Stable, high power, high efficiency picosecond ultraviolet generation at 355 nm in K3B6O10 Br crystal

NASA Astrophysics Data System (ADS)

Hou, Z. Y.; Wang, L. R.; Xia, M. J.; Yan, D. X.; Zhang, Q. L.; Zhang, L.; Liu, L. J.; Xu, D. G.; Zhang, D. X.; Wang, X. Y.; Li, R. K.; Chen, C. T.

2018-06-01

We demonstrate a high efficiency and high power picosecond ultraviolet source at 355 nm with stable output by sum frequency generation from a Nd:YAG laser using a type-I critically phase matched K3B6O10 Br crystal as nonlinear optical material. Conversion efficiency as high as 30.8% was achieved using a 25 ps laser at 1064 nm operated at 10 Hz. Similar work is done by using a 35 W 10 ps laser at 1064 nm as the pump source with a repetition rate of 80 MHz, and the highest average output power obtained was up to 5.3 W. In addition, the power stability of the 355 nm output power measurement shows that the standard deviation fluctuations of the average power are ±0.69% and ±0.91% at 3.0 W and 3.5 W, respectively.

The relationship between wind power, electricity demand and winter weather patterns in Great Britain

NASA Astrophysics Data System (ADS)

Thornton, Hazel E.; Scaife, Adam A.; Hoskins, Brian J.; Brayshaw, David J.

2017-06-01

Wind power generation in Great Britain has increased markedly in recent years. However due to its intermittency its ability to provide power during periods of high electricity demand has been questioned. Here we characterise the winter relationship between electricity demand and the availability of wind power. Although a wide range of wind power capacity factors is seen for a given demand, the average capacity factor reduces by a third between low and high demand. However, during the highest demand average wind power increases again, due to strengthening easterly winds. The nature of the weather patterns affecting Great Britain are responsible for this relationship. High demand is driven by a range of high pressure weather types, each giving cold conditions, but variable wind power availability. Offshore wind power is sustained at higher levels and offers a more secure supply compared to that onshore. However, during high demand periods in Great Britain neighbouring countries may struggle to provide additional capacity due to concurrent low temperatures and low wind power availability.

Measured radiofrequency exposure during various mobile-phone use scenarios.

PubMed

Kelsh, Michael A; Shum, Mona; Sheppard, Asher R; McNeely, Mark; Kuster, Niels; Lau, Edmund; Weidling, Ryan; Fordyce, Tiffani; Kühn, Sven; Sulser, Christof

2011-01-01

Epidemiologic studies of mobile phone users have relied on self reporting or billing records to assess exposure. Herein, we report quantitative measurements of mobile-phone power output as a function of phone technology, environmental terrain, and handset design. Radiofrequency (RF) output data were collected using software-modified phones that recorded power control settings, coupled with a mobile system that recorded and analyzed RF fields measured in a phantom head placed in a vehicle. Data collected from three distinct routes (urban, suburban, and rural) were summarized as averages of peak levels and overall averages of RF power output, and were analyzed using analysis of variance methods. Technology was the strongest predictor of RF power output. The older analog technology produced the highest RF levels, whereas CDMA had the lowest, with GSM and TDMA showing similar intermediate levels. We observed generally higher RF power output in rural areas. There was good correlation between average power control settings in the software-modified phones and power measurements in the phantoms. Our findings suggest that phone technology, and to a lesser extent, degree of urbanization, are the two stronger influences on RF power output. Software-modified phones should be useful for improving epidemiologic exposure assessment.

High-energy ultra-short pulse thin-disk lasers: new developments and applications

NASA Astrophysics Data System (ADS)

Michel, Knut; Klingebiel, Sandro; Schultze, Marcel; Tesseit, Catherine Y.; Bessing, Robert; Häfner, Matthias; Prinz, Stefan; Sutter, Dirk; Metzger, Thomas

2016-03-01

We report on the latest developments at TRUMPF Scientific Lasers in the field of ultra-short pulse lasers with highest output energies and powers. All systems are based on the mature and industrialized thin-disk technology of TRUMPF. Thin Yb:YAG disks provide a reliable and efficient solution for power and energy scaling to Joule- and kW-class picosecond laser systems. Due to its efficient one dimensional heat removal, the thin-disk exhibits low distortions and thermal lensing even when pumped under extremely high pump power densities of 10kW/cm². Currently TRUMPF Scientific Lasers develops regenerative amplifiers with highest average powers, optical parametric amplifiers and synchronization schemes. The first few-ps kHz multi-mJ thin-disk regenerative amplifier based on the TRUMPF thindisk technology was developed at the LMU Munich in 20081. Since the average power and energy have continuously been increased, reaching more than 300W (10kHz repetition rate) and 200mJ (1kHz repetition rate) at pulse durations below 2ps. First experiments have shown that the current thin-disk technology supports ultra-short pulse laser solutions >1kW of average power. Based on few-picosecond thin-disk regenerative amplifiers few-cycle optical parametric chirped pulse amplifiers (OPCPA) can be realized. These systems have proven to be the only method for scaling few-cycle pulses to the multi-mJ energy level. OPA based few-cycle systems will allow for many applications such as attosecond spectroscopy, THz spectroscopy and imaging, laser wake field acceleration, table-top few-fs accelerators and laser-driven coherent X-ray undulator sources. Furthermore, high-energy picosecond sources can directly be used for a variety of applications such as X-ray generation or in atmospheric research.

High power passive mode-locked L-band fiber laser based on microfiber topological insulator saturable absorber

NASA Astrophysics Data System (ADS)

Semaan, Georges; Meng, Yichang; Salhi, Mohamed; Niang, Alioune; Guesmi, Khmaies; Luo, Zhi-Chao; Sanchez, Francois

2016-04-01

In this communication, we demonstrate a passive mode-locked Er:Yb co-doped double-clad fiber laser using a tapered microfiber topological insulator (Bi2Se3) saturable absorber (TISA). The topological insulator is drop-casted onto the tapered fiber and optically deposited by optical tweezer effect. We use a ring laser setup including the fabricated TISA. By carefully optimizing the cavity losses and output coupling ratio, the mode-locked laser can operate in L-band with a high average output power. At a maximum pump power of 5 W, we obtain the 91st harmonic mode-locking of soliton bunches with a 3dB spectral bandwidth of 1.06nm, a repetition rate of 640.9 MHz and an average output power of 308mW. As far as we know, this is the highest output power yet reported of a mode-locked fiber laser operating with a TISA.

PAVE PAWS Early Warning Radar Operation Cape Cod Air Force Station, MA. Record of Decision

DTIC Science & Technology

2009-06-01

Electrical and Electronics Engineers (IEEE) C95.1-1999. Accordingly, the highest measurement was obtained directly in front of the feedhorn (i.e...waveform characterization of the Cape Cod AFS Pave PAWS radar. The data acquired during the Phase IV survey indicated that the electric fields produced...level observed among the ambient sites. During this survey, peak/average power density measurements and peak/average electric field measurements

Nonlinear pulse compression stage delivering 43-W few-cycle pulses with GW peak-power at 2-μm wavelength

NASA Astrophysics Data System (ADS)

Gebhardt, Martin; Gaida, Christian; Heuermann, T.; Stutzki, F.; Jauregui, C.; Antonio-Lopez, J.; Schüuzgen, A.; Amezcua-Correa, R.; Tünnermann, A.; Limpert, J.

2018-02-01

In this contribution we demonstrate the nonlinear pulse compression of an ultrafast thulium-doped fiber laser down to 14 fs FWHM duration (sub-3 optical cycles) at a record average power of 43 W and 34.5 μJ pulse energy. To the best of our knowledge, we present the highest average power few-cycle laser source at 2 μm wavelength. This performance level in combination with GW-class peak power makes our laser source extremely interesting for driving high-harmonic generation or for generating mid-infrared frequency combs via intra-pulse frequency down-conversion at an unprecedented average power. The experiments were enabled by an ultrafast thulium-doped fiber laser delivering 110 fs pulses at high repetition rates, and an argon gas-filled antiresonant hollow-core fiber (ARHCF) with excellent transmission and weak anomalous dispersion, leading to the self-compression of the pulses. We have shown that ARHCFs are well-suited for nonlinear pulse compression around 2 μm wavelength and that this concept features excellent power handling capabilities. Based on this result, we discuss the next steps for energy and average power scaling including upscaling the fiber dimensions in order to fully exploit the capabilities of our laser system, which can deliver several GW of peak power. This way, a 100 W-class laser source with mJ-level few-cycle pulses at 2 μm wavelength is feasible in the near future.

A cladding-pumped, tunable holmium doped fiber laser.

PubMed

Simakov, Nikita; Hemming, Alexander; Clarkson, W Andrew; Haub, John; Carter, Adrian

2013-11-18

We present a tunable, high power cladding-pumped holmium doped fiber laser. The laser generated >15 W CW average power across a wavelength range of 2.043 - 2.171 μm, with a maximum output power of 29.7 W at 2.120 μm. The laser also produced 18.2 W when operating at 2.171 µm. To the best of our knowledge this is the highest power operation of a holmium doped laser at a wavelength >2.15 µm. We discuss the significance of background losses and fiber design for achieving efficient operation in holmium doped fibers.

Passively mode-locked Nd:YVO4 laser operating at 1073 nm and 1085 nm

NASA Astrophysics Data System (ADS)

Waritanant, Tanant; Major, Arkady

2018-02-01

A passively mode-locked Nd:YVO4 laser operating at 1073 nm and 1085 nm was demonstrated with an intracavity birefringent filter as the wavelength selecting element. The average output powers achieved were 2.17 W and 2.18 W with optical-to-optical efficiency of 19.6% and 19.7%, respectively. The slope efficiencies were more than 31% at both output wavelengths. The pulse durations at the highest average output power were 10.3 ps and 8.4 ps, respectively. We believe that this is the first report of mode locking of a Nd:YVO4 laser operating at 1073 nm or 1085 nm lines.

Ruthenium Oxide Electrochemical Super Capacitor Optimization for Pulse Power Applications

NASA Technical Reports Server (NTRS)

Merryman, Stephen A.; Chen, Zheng

2000-01-01

Electrical actuator systems are being pursued as alternatives to hydraulic systems to reduce maintenance time, weight and costs while increasing reliability. Additionally, safety and environmental hazards associated with the hydraulic fluids can be eliminated. For most actuation systems, the actuation process is typically pulsed with high peak power requirements but with relatively modest average power levels. The power-time requirements for electrical actuators are characteristic of pulsed power technologies where the source can be sized for the average power levels while providing the capability to achieve the peak requirements. Among the options for the power source are battery systems, capacitor systems or battery-capacitor hybrid systems. Battery technologies are energy dense but deficient in power density; capacitor technologies are power dense but limited by energy density. The battery-capacitor hybrid system uses the battery to supply the average power and the capacitor to meet the peak demands. It has been demonstrated in previous work that the hybrid electrical power source can potentially provide a weight savings of approximately 59% over a battery-only source. Electrochemical capacitors have many properties that make them well-suited for electrical actuator applications. They have the highest demonstrated energy density for capacitive storage (up to 100 J/g), have power densities much greater than most battery technologies (greater than 30kW/kg), are capable of greater than one million charge-discharge cycles, can be charged at extremely high rates, and have non-explosive failure modes. Thus, electrochemical capacitors exhibit a combination of desirable battery and capacitor characteristics.

A Co2+-doped alumina-rich Mg0.4Al2.4O4 spinel crystal as saturable absorber for a LD pumped Er: glass microchip laser at 1535 nm

NASA Astrophysics Data System (ADS)

Jiang, D. P.; Zou, Y. Q.; Su, L. B.; Tang, H. L.; Wu, F.; Zheng, L. H.; Li, H. J.; Xu, J.

2011-05-01

Co2+-doped Mg0.4Al2.4O4 single crystal up to varnothing28×40 mm3 was successfully grown by the Czochralski method. By using this crystal as saturable absorber, we have demonstrated a diode-end-pumped passively Q-switched Er:glass microchip laser operating at 1535 nm for the first time to the best of our knowledge. The dependences of average output power, repetition rate and pulse energy on the incident pump power were investigated. In the passive Q-switching regime, a maximum average output power of 22.12 mW was obtained at the incident pump power of 410 mW. The narrowest pulse width, the largest pulse energy and the highest peak power were obtained to be about 3.5 ns, 4.8 μJ, and 1.37 kW, respectively.

Tissue refractometry using Hilbert phase microscopy.

PubMed

Lue, Niyom; Bewersdorf, Joerg; Lessard, Mark D; Badizadegan, Kamran; Dasari, Ramachandra R; Feld, Michael S; Popescu, Gabriel

2007-12-15

We present, for the first time to our knowledge, quantitative phase images associated with unstained 5 mum thick tissue slices of mouse brain, spleen, and liver. The refractive properties of the tissue are retrieved in terms of the average refractive index and its spatial variation. We find that the average refractive index varies significantly with tissue type, such that the brain is characterized by the lowest value and the liver by the highest. The spatial power spectra of the phase images reveal power law behavior with different exponents for each tissue type. This approach opens a new possibility for stain-free characterization of tissues, where the diagnostic power is provided by the intrinsic refractive properties of the biological structure. We present results obtained for liver tissue affected by a lysosomal storage disease and show that our technique can quantify structural changes during this disease development.

OMI air-quality monitoring over the Middle East

NASA Astrophysics Data System (ADS)

Barkley, Michael P.; González Abad, Gonzalo; Kurosu, Thomas P.; Spurr, Robert; Torbatian, Sara; Lerot, Christophe

2017-04-01

Using Ozone Monitoring Instrument (OMI) trace gas vertical column observations of nitrogen dioxide (NO2), formaldehyde (HCHO), sulfur dioxide (SO2), and glyoxal (CHOCHO), we have conducted a robust and detailed time series analysis to assess changes in local air quality for over 1000 locations (focussing on urban, oil refinery, oil port, and power plant targets) over the Middle East for 2005-2014. Apart from NO2, which is highest over urban locations, average tropospheric column levels of these trace gases are highest over oil ports and refineries. The highest average pollution levels over urban settlements are typically in Bahrain, Kuwait, Qatar, and the United Arab Emirates. We detect 278 statistically significant and real linear NO2 trends in total. Over urban areas NO2 increased by up to 12 % yr-1, with only two locations showing a decreasing trend. Over oil refineries, oil ports, and power plants, NO2 increased by about 2-9 % yr-1. For HCHO, 70 significant and real trends were detected, with HCHO increasing by 2-7 % yr-1 over urban settlements and power plants and by about 2-4 % yr-1 over refineries and oil ports. Very few SO2 trends were detected, which varied in direction and magnitude (23 increasing and 9 decreasing). Apart from two locations where CHOCHO is decreasing, we find that glyoxal tropospheric column levels are not changing over the Middle East. Hence, for many locations in the Middle East, OMI observes a degradation in air quality over 2005-2014. This study therefore demonstrates the capability of OMI to generate long-term air-quality monitoring at local scales over this region.

Oahu wind power survey, first report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramage, C.S.; Daniels, P.A.; Schroeder, T.A.

1977-05-01

A wind power survey has been conducted on Oahu since summer 1975. At seventeen potentially windy sites, calibrated anemometers and wind vanes were installed and recordings made on computer-processable magnetic tape cassettes. From monthly mean wind speeds--normalized by comparing with Honolulu Airport means winds--it was concluded that about 23 mi/hr represented the highest average annual wind speed likely to be attained on Oahu and that the Koko Head and Kahuku areas gave the most promise for wind energy generation. Diurnal variation of the wind in these areas roughly parallels diurnal variation of electric power demand.

Ultrafast disk technology enables next generation micromachining laser sources

NASA Astrophysics Data System (ADS)

Heckl, Oliver H.; Weiler, Sascha; Luzius, Severin; Zawischa, Ivo; Sutter, Dirk

2013-02-01

Ultrashort pulsed lasers based on thin disk technology have entered the 100 W regime and deliver several tens of MW peak power without chirped pulse amplification. Highest uptime and insensitivity to back reflections make them ideal tools for efficient and cost effective industrial micromachining. Frequency converted versions allow the processing of a large variety of materials. On one hand, thin disk oscillators deliver more than 30 MW peak power directly out of the resonator in laboratory setups. These peak power levels are made possible by recent progress in the scaling of the pulse energy in excess of 40 μJ. At the corresponding high peak intensity, thin disk technology profits from the limited amount of material and hence the manageable nonlinearity within the resonator. Using new broadband host materials like for example the sesquioxides will eventually reduce the pulse duration during high power operation and further increase the peak power. On the other hand industry grade amplifier systems deliver even higher peak power levels. At closed-loop controlled 100W, the TruMicro Series 5000 currently offers the highest average ultrafast power in an industry proven product, and enables efficient micromachining of almost any material, in particular of glasses, ceramics or sapphire. Conventional laser cutting of these materials often requires UV laser sources with pulse durations of several nanoseconds and an average power in the 10 W range. Material processing based on high peak power laser sources makes use of multi-photon absorption processes. This highly nonlinear absorption enables micromachining driven by the fundamental (1030 nm) or frequency doubled (515 nm) wavelength of Yb:YAG. Operation in the IR or green spectral range reduces the complexity and running costs of industrial systems initially based on UV light sources. Where UV wavelength is required, the TruMicro 5360 with a specified UV crystal life-time of more than 10 thousand hours of continues operation at 15W is an excellent choice. Currently this is the world's most powerful industrial sub-10 ps UV laser.

Tissue refractometry using Hilbert phase microscopy

PubMed Central

Lue, Niyom; Bewersdorf, Joerg; Lessard, Mark D.; Badizadegan, Kamran; Dasari, Ramachandra R.; Feld, Michael S.; Popescu, Gabriel

2009-01-01

We present, for the first time to our knowledge, quantitative phase images associated with unstained 5 μm thick tissue slices of mouse brain, spleen, and liver. The refractive properties of the tissue are retrieved in terms of the average refractive index and its spatial variation. We find that the average refractive index varies significantly with tissue type, such that the brain is characterized by the lowest value and the liver by the highest. The spatial power spectra of the phase images reveal power law behavior with different exponents for each tissue type. This approach opens a new possibility for stain-free characterization of tissues, where the diagnostic power is provided by the intrinsic refractive properties of the biological structure. We present results obtained for liver tissue affected by a lysosomal storage disease and show that our technique can quantify structural changes during this disease development. PMID:18087529

Possibilities and limitations of wind energy utilisation

NASA Astrophysics Data System (ADS)

Feustel, J.

1981-10-01

The existing wind resource, the most favorable locations, applications, and designs of windpowered generators are reviewed, along with descriptions of current and historic wind turbines and lines of research. Coastal regions, plains, hill summits, and mountains with funneling regions are noted to have the highest annual wind averages, with energy densities exceeding the annual solar insolation at average wind speeds of 5-7.9 m/sec. Applications for utility-grade power production, for irrigation, for mechanical heat production, and for pumped storage in water towers or reservoirs are mentioned, as well as electrical power production in remote areas and for hydrogen production by electrolysis. Power coefficients are discussed, with attention given to the German Growian 3 MW machine. It is shown that the least economically sound wind turbines, the machines with outputs below 100 kW, can vie with diesel plant economics in a good wind regime if the wind turbine operates for 15 yr.

Compact high-efficiency 100-W-level diode-side-pumped Nd:YAG laser with linearly polarized TEM00 mode output.

PubMed

Xu, Yi-Ting; Xu, Jia-Lin; Guo, Ya-Ding; Yang, Feng-Tu; Chen, Yan-Zhong; Xu, Jian; Xie, Shi-Yong; Bo, Yong; Peng, Qin-Jun; Cui, Dafu; Xu, Zu-Yan

2010-08-20

We present a compact high-efficiency and high-average-power diode-side-pumped Nd:YAG rod laser oscillator operated with a linearly polarized fundamental mode. The oscillator resonator is based on an L-shaped convex-convex cavity with an improved module and a dual-rod configuration for birefringence compensation. Under a pump power of 344 W, a linearly polarized average output power of 101.4 W at 1064 nm is obtained, which corresponds to an optical-to-optical conversion efficiency of 29.4%. The laser is operated at a repetition rate of 400 Hz with a beam quality factor of M(2)=1.14. To the best of our knowledge, this is the highest optical-to-optical efficiency for a side-pumped TEM(00) Nd:YAG rod laser oscillator with a 100-W-level output ever reported.

An unexpected rise in strontium-90 in US deciduous teeth in the 1990s.

PubMed

Mangano, Joseph J; Gould, Jay M; Sternglass, Ernest J; Sherman, Janette D; McDonnell, William

2003-12-30

For several decades, the United States has been without an ongoing program measuring levels of fission products in the body. Strontium-90 (Sr-90) concentrations in 2089 deciduous (baby) teeth, mostly from persons living near nuclear power reactors, reveal that average levels rose 48.5% for persons born in the late 1990s compared to those born in the late 1980s. This trend represents the first sustained increase since the early 1960s, before atmospheric weapons tests were banned. The trend was consistent for each of the five states for which at least 130 teeth are available. The highest averages were found in southeastern Pennsylvania, and the lowest in California (San Francisco and Sacramento), neither of which is near an operating nuclear reactor. In each state studied, the average Sr-90 concentration is highest in counties situated closest to nuclear reactors. It is likely that, 40 years after large-scale atmospheric atomic bomb tests ended, much of the current in-body radioactivity represents nuclear reactor emissions.

High-precision laser microcutting and laser microdrilling using diffractive beam-splitting and high-precision flexible beam alignment

NASA Astrophysics Data System (ADS)

Zibner, F.; Fornaroli, C.; Holtkamp, J.; Shachaf, Lior; Kaplan, Natan; Gillner, A.

2017-08-01

High-precision laser micro machining gains more importance in industrial applications every month. Optical systems like the helical optics offer highest quality together with controllable and adjustable drilling geometry, thus as taper angle, aspect ratio and heat effected zone. The helical optics is based on a rotating Dove-prism which is mounted in a hollow shaft engine together with other optical elements like wedge prisms and plane plates. Although the achieved quality can be interpreted as extremely high the low process efficiency is a main reason that this manufacturing technology has only limited demand within the industrial market. The objective of the research studies presented in this paper is to dramatically increase process efficiency as well as process flexibility. During the last years, the average power of commercial ultra-short pulsed laser sources has increased significantly. The efficient utilization of the high average laser power in the field of material processing requires an effective distribution of the laser power onto the work piece. One approach to increase the efficiency is the application of beam splitting devices to enable parallel processing. Multi beam processing is used to parallelize the fabrication of periodic structures as most application only require a partial amount of the emitted ultra-short pulsed laser power. In order to achieve highest flexibility while using multi beam processing the single beams are diverted and re-guided in a way that enables the opportunity to process with each partial beam on locally apart probes or semimanufactures.

Characterization of plasma parameters in shaped PBX-M discharges

NASA Astrophysics Data System (ADS)

England, A. C.; Bell, R. E.; Hirshman, S. P.; Kaita, R.; Kugel, H. W.; LeBlanc, B. L.; Lee, D. K.; Okabayashi, M.; Sun, Y.-C.; Takahashi, H.

1997-09-01

The Princeton Beta Experiment-Modification (PBX-M) was run both with elliptical and with bean-shaped plasmas during the 1992 and 1993 operating periods. Two deuterium-fed neutral beams were used for auxiliary heating, and during 1992 the average power was 0741-3335/39/9/008/img13. This will be referred to as the lower neutral-beam power (LNBP) period. As many as four deuterium-fed neutral beams were used during 1993, and the average power was 0741-3335/39/9/008/img14. This will be referred to as the medium neutral-beam power (MNBP) period. The neutron source strength, Sn, showed a scaling with injected power 0741-3335/39/9/008/img15, 0741-3335/39/9/008/img16 for both the LMBP and MNBP periods. A much wider range of shaping parameters was studied during the MNBP as compared with the LNBP period. A weak positive dependence on bean shaping was observed for the LNBP, and a stronger positive dependence on shaping was observed for MNBP, viz 0741-3335/39/9/008/img17. High values of Sn were obtained in bean-shaped plasmas for the highest values of 0741-3335/39/9/008/img18 at 0741-3335/39/9/008/img19 for the LNBP. For the MNBP the highest values of Sn and stored energy were obtained at 0741-3335/39/9/008/img19, and the highest values of 0741-3335/39/9/008/img18 were obtained at 0741-3335/39/9/008/img22. The achievement of high Sn is aided by high neutral-beam power, high toroidal field, strong shaping, high electron temperature, and broad profiles. The achievement of high 0741-3335/39/9/008/img18 is aided by low toroidal field, high density, less shaping, broad profiles, and access to the H-mode, viz 0741-3335/39/9/008/img24. The achievement of high 0741-3335/39/9/008/img25 is aided by strong shaping, high density, broad profiles, and access to the H-mode, viz 0741-3335/39/9/008/img26. Some comparisons with the previous higher neutral-beam (HNBP) period in 1989 are also made.

Laser-diode pumped 40-W Yb:YAG ceramic laser.

PubMed

Hao, Qiang; Li, Wenxue; Pan, Haifeng; Zhang, Xiaoyi; Jiang, Benxue; Pan, Yubai; Zeng, Heping

2009-09-28

We demonstrated a high-power continuous-wave (CW) polycrystalline Yb:YAG ceramic laser pumped by fiber-pigtailed laser diode at 968 nm with 400 mum fiber core. The Yb:YAG ceramic laser performance was compared for different Yb(3+) ion concentrations in the ceramics by using a conventional end-pump laser cavity consisting of two flat mirrors with output couplers of different transmissions. A CW laser output of 40 W average power with M(2) factor of 5.8 was obtained with 5 mol% Yb concentration under 120 W incident pump power. This is to the best of our knowledge the highest output power in end-pumped bulk Yb:YAG ceramic laser.

Comparison of the biometric formulas used for applanation A-scan ultrasound biometry.

PubMed

Özcura, Fatih; Aktaş, Serdar; Sağdık, Hacı Murat; Tetikoğlu, Mehmet

2016-10-01

The purpose of the study was to compare the accuracy of various biometric formulas for predicting postoperative refraction determined using applanation A-scan ultrasound. This retrospective comparative study included 485 eyes that underwent uneventful phacoemulsification with intraocular lens (IOL) implantation. Applanation A-scan ultrasound biometry and postoperative manifest refraction were obtained in all eyes. Biometric data were entered into each of the five IOL power calculation formulas: SRK-II, SRK/T, Holladay I, Hoffer Q, and Binkhorst II. All eyes were divided into three groups according to axial length: short (≤22.0 mm), average (22.0-25.0 mm), and long (≥25.0 mm) eyes. The postoperative spherical equivalent was calculated and compared with the predicted refractive error using each biometric formula. The results showed that all formulas had significantly lower mean absolute error (MAE) in comparison with Binkhorst II formula (P < 0.01). The lowest MAE was obtained with the SRK-II for average (0.49 ± 0.40 D) and short (0.67 ± 0.54 D) eyes and the SRK/T for long (0.61 ± 0.50 D) eyes. The highest postoperative hyperopic shift was seen with the SRK-II for average (46.8 %), short (28.1 %), and long (48.4 %) eyes. The highest postoperative myopic shift was seen with the Holladay I for average (66.4 %) and long (71.0 %) eyes and the SRK/T for short eyes (80.6 %). In conclusion, the SRK-II formula produced the lowest MAE in average and short eyes and the SRK/T formula produced the lowest MAE in long eyes. The SRK-II has the highest postoperative hyperopic shift in all eyes. The highest postoperative myopic shift is with the Holladay I for average and long eyes and SRK/T for short eyes.

Actively mode-locked Tm-Ho:LiYF4 and Tm-Ho:BaY2F8 lasers

NASA Astrophysics Data System (ADS)

Gatti, D.; Galzerano, G.; Toncelli, A.; Tonelli, M.; Laporta, P.

2007-01-01

We report on the generation of mode-locking pulse trains with high average output powers from diode-pumped Tm-Ho:LiYF4 and Tm-Ho:BaY2F8 lasers emitting at around 2 μm. The highest output power of 365 mW was obtained with the Tm-Ho:YLF4 laser, whereas the shortest pulse duration of 120 ps and the widest tunability range of 59 nm was achieved with the Tm-Ho:BaY2F8 laser.

A highly efficient and compact long pulse Nd:YAG rod laser with 540 J of pulse energy for welding application.

PubMed

Choubey, Ambar; Vishwakarma, S C; Misra, Pushkar; Jain, R K; Agrawal, D K; Arya, R; Upadhyaya, B N; Oak, S M

2013-07-01

We have developed an efficient and high average power flash lamp pumped long pulse Nd:YAG laser capable of generating 1 kW of average output power with maximum 540 J of single pulse energy and 20 kW of peak power. The laser pulse duration can be varied from 1 to 40 ms and repetition rate from 1 to 100 Hz. A compact and robust laser pump chamber and resonator was designed to achieve this high average and peak power. It was found that this laser system provides highest single pulse energy as compared to other long pulsed Nd:YAG laser systems of similar rating. A slope efficiency of 5.4% has been achieved, which is on higher side for typical lamp pumped solid-state lasers. This system will be highly useful in laser welding of materials such as aluminium and titanium. We have achieved 4 mm deep penetration welding of these metals under optimized conditions of output power, pulse energy, and pulse duration. The laser resonator was optimized to provide stable operation from single shot to 100 Hz of repetition rate. The beam quality factor was measured to be M(2) ~ 91 and pulse-to-pulse stability of ±3% for the multimode operation. The laser beam was efficiently coupled through an optical fiber of 600 μm core diameter and 0.22 numerical aperture with power transmission of 90%.

Double spacing multi-wavelength Brillouin Raman fiber laser of eight-shaped structure utilizing Raman amplifier

NASA Astrophysics Data System (ADS)

Madin, M. Sya'aer; Ahmad Hambali, N. A. M.; Shahimin, M. M.; Wahid, M. H. A.; Roshidah, N.; Azaidin, M. A. M.

2017-02-01

In this paper, double frequency spacing of multi-wavelength Brillouin Raman fiber laser utilizing eight-shaped structure in conjunction with Raman amplifier is simulated and demonstrated using Optisys software. Double frequency multiwavelength Brillouin Raman fiber laser is one of the solution for single frequency spacing channel de-multiplexing from narrow single spacing in the communication systems. The eight-shaped structure has the ability to produce lower noise and double frequency spacing. The 7 km of single mode fiber acting as a nonlinear medium for the generation of Stimulated Brillouin Scattering and Stimulated Raman Scattering. As a results, the optimum results are recorded at 1450 nm of RP power at 22 dBm and 1550 nm of BP power at 20 dBm. These parameters provide a high output peak power, gain and average OSNR. The highest peak power of Stokes 1 is recorded at 90% of coupling ratio which is 29.88 dBm. It is found that the maximum gain and average OSNR of about 1.23 dB and 63.74 dB.

Short-term load forecasting of power system

NASA Astrophysics Data System (ADS)

Xu, Xiaobin

2017-05-01

In order to ensure the scientific nature of optimization about power system, it is necessary to improve the load forecasting accuracy. Power system load forecasting is based on accurate statistical data and survey data, starting from the history and current situation of electricity consumption, with a scientific method to predict the future development trend of power load and change the law of science. Short-term load forecasting is the basis of power system operation and analysis, which is of great significance to unit combination, economic dispatch and safety check. Therefore, the load forecasting of the power system is explained in detail in this paper. First, we use the data from 2012 to 2014 to establish the partial least squares model to regression analysis the relationship between daily maximum load, daily minimum load, daily average load and each meteorological factor, and select the highest peak by observing the regression coefficient histogram Day maximum temperature, daily minimum temperature and daily average temperature as the meteorological factors to improve the accuracy of load forecasting indicators. Secondly, in the case of uncertain climate impact, we use the time series model to predict the load data for 2015, respectively, the 2009-2014 load data were sorted out, through the previous six years of the data to forecast the data for this time in 2015. The criterion for the accuracy of the prediction is the average of the standard deviations for the prediction results and average load for the previous six years. Finally, considering the climate effect, we use the BP neural network model to predict the data in 2015, and optimize the forecast results on the basis of the time series model.

Coordination of multiple appendages in drag-based swimming.

PubMed

Alben, Silas; Spears, Kevin; Garth, Stephen; Murphy, David; Yen, Jeannette

2010-11-06

Krill are aquatic crustaceans that engage in long distance migrations, either vertically in the water column or horizontally for 10 km (over 200,000 body lengths) per day. Hence efficient locomotory performance is crucial for their survival. We study the swimming kinematics of krill using a combination of experiment and analysis. We quantify the propulsor kinematics for tethered and freely swimming krill in experiments, and find kinematics that are very nearly metachronal. We then formulate a drag coefficient model which compares metachronal, synchronous and intermediate motions for a freely swimming body with two legs. With fixed leg velocity amplitude, metachronal kinematics give the highest average body speed for both linear and quadratic drag laws. The same result holds for five legs with the quadratic drag law. When metachronal kinematics is perturbed towards synchronous kinematics, an analysis shows that the velocity increase on the power stroke is outweighed by the velocity decrease on the recovery stroke. With fixed time-averaged work done by the legs, metachronal kinematics again gives the highest average body speed, although the advantage over synchronous kinematics is reduced.

Energy gain calculations in Penning fusion systems using a bounce-averaged Fokker-Planck model

NASA Astrophysics Data System (ADS)

Chacón, L.; Miley, G. H.; Barnes, D. C.; Knoll, D. A.

2000-11-01

In spherical Penning fusion devices, a spherical cloud of electrons, confined in a Penning-like trap, creates the ion-confining electrostatic well. Fusion energy gains for these systems have been calculated in optimistic conditions (i.e., spherically uniform electrostatic well, no collisional ion-electron interactions, single ion species) using a bounce-averaged Fokker-Planck (BAFP) model. Results show that steady-state distributions in which the Maxwellian ion population is dominant correspond to lowest ion recirculation powers (and hence highest fusion energy gains). It is also shown that realistic parabolic-like wells result in better energy gains than square wells, particularly at large well depths (>100 kV). Operating regimes with fusion power to ion input power ratios (Q-value) >100 have been identified. The effect of electron losses on the Q-value has been addressed heuristically using a semianalytic model, indicating that large Q-values are still possible provided that electron particle losses are kept small and well depths are large.

Nonlinear mirror modelocking of a bounce geometry laser.

PubMed

Thomas, G M; Bäuerle, A; Farrell, D J; Damzen, M J

2010-06-07

We present the investigation of nonlinear mirror modelocking (NLM) of a bounce amplifier laser. This technique, a potential rival to SESAM modelocking, uses a nonlinear crystal and a dichroic mirror to passively modelock a Nd:GdVO(4) slab bounce amplifier operating at 1063nm. At 11.3W, we present the highest power achieved using the NLM technique, using type-II phase-matched KTP, with a pulse duration of 57ps. Using type-I phase-matched BiBO, modelocking was achieved with a shorter pulse duration of 5.7ps at an average power of 7.1W.

High average/peak power linearly polarized all-fiber picosecond MOPA seeded by mode-locked noise-like pulses

NASA Astrophysics Data System (ADS)

Yu, H. L.; Ma, P. F.; Tao, R. M.; Wang, X. L.; Zhou, P.; Chen, J. B.

2015-06-01

The characteristics of mode-locked noise-like pulses generated from a passively mode-locked fiber oscillator are experimentally investigated. By carefully adjusting the two polarization controllers, stable mode-locked noise-like pulse emission with a high radio frequency signal/noise ratio of  >55 dB is successfully achieved, ensuring the safety and possibility of high power amplification. To investigate the amplification characteristics of such pulses, one all-fiber master oscillator power amplifier (MOPA) is built to boost the power and energy of such pulses. Amplified noise-like pulses with average output power of 423 W, repetition rate of 18.71 MHz, pulse energy of 22.61 μJ, pulse duration of 72.1 ps and peak power of 314 kW are obtained. Near diffraction-limited beam is also demonstrated with M2 factor measured at full power operation of ~1.2 in the X and Y directions. The polarization extinction ratio at output power of 183 W is measured to be ~13 dB. To the best of our knowledge, this is the first demonstration of high-power amplification of noise-like pulses and the highest peak power ever reported in all-fiber picosecond MOPAs. The temporal self-compression process of such pulses and high peak power when amplified make it an ideal pump source for generation of high-power supercontinuum. Other potential applications, such as material processing and optical coherent tomography, could also be foreseen.

An inter-lighting interference cancellation scheme for MISO-VLC systems

NASA Astrophysics Data System (ADS)

Kim, Kyuntak; Lee, Kyujin; Lee, Kyesan

2017-08-01

In this paper, we propose an inter-lighting interference cancellation (ILIC) scheme to reduce the interference between adjacent light-emitting diodes (LEDs) and enhance the transmission capacity of multiple-input-single-output (MISO)-visible light communication (VLC) systems. In indoor environments, multiple LEDs have normally been used as lighting sources, allowing the design of MISO-VLC systems. To enhance the transmission capacity, different data should be simultaneously transmitted from each LED; however, that can lead to interference between adjacent LEDs. In that case, relatively low-received power signals are subjected to large interference because wireless optical systems generally use intensity modulation and direct detection. Thus, only the signal with the highest received power can be detected, while the other received signals cannot be detected. To solve this problem, we propose the ILIC scheme for MISO-VLC systems. The proposed scheme preferentially detects the highest received power signal, and this signal is referred as interference signal by an interference component generator. Then, relatively low-received power signal can be detected by cancelling the interference signal from the total received signals. Therefore, the performance of the proposed scheme can improve the total average bit error rate and throughput of a MISO-VLC system.

Can Facebook pages be a mode of blended learning to supplement in-class teaching in Saudi Arabia?

PubMed

Anwar, Khurshid; Sajid, Muhammad Raihan; Cahusac, Peter; Shaikh, Abdul Ahad; Elgammal, Ahmad; Alshedoukhy, Ahlam; Kashir, Junaid

2017-09-01

The aim of this study was to examine the potential of a self-designed Facebook page on Neuroscience, to supplement in-class teaching as a mode of blended learning. Posts were split into multiple choice questions (MCQs), general interest articles, neuroscience-related external links and resources, and lecture notes and PowerPoint presentations. The study was divided into three distinct phases: before, during, and after the Neuroscience block. Student responses were evaluated via a self-developed questionnaire. Grades achieved by students undertaking the block in 2015 and 2014 were recorded, as were the grades achieved by the same cohort in concurrent blocks in the same year of study. Results showed that ~80% of students reported that use of the page enhanced their overall subject knowledge and exam preparation. Highest page activity occurred during the Neuroscience block. Peak activity occurred directly before summative assessments, with MCQ posts having the highest impact. The cohort of students with access to the Facebook page achieved better grades in the block compared with the previous cohort, despite similar average performance in other subjects. We demonstrate the utility of Facebook as a powerful tool for undergraduate education, supplementing in-class teaching, and assisting in exam preparation, potentially increasing average student performance. Copyright © 2017 the American Physiological Society.

LD-pumped actively Q-switched c-cut Nd:GdVO4 self-Raman laser operating at 1166 and 1176 nm

NASA Astrophysics Data System (ADS)

Sun, Xinzhi; Zhang, Xihe; Li, Shutao; Dong, Yuan

2017-12-01

A laser diode pumped actively Q-switched c-cut Nd:GdVO4 self-Raman laser is experimentally investigated. Simultaneous pulse outputs at 1166 nm and 1176 nm corresponding to the Raman shifts of 807 and 882 cm-1 are acquired. At the pulse repetition frequency (PRF) of 20 kHz, the maximum output power is 103 mW at 1166 nm with the incident pump power of 2.31 W, while 1176 nm output power reaches 530 mW with the incident pump power of 4.11 W. The maximum output power of Raman laser is 570 mW with the incident pump power of 4.11 W and the PRF of 30 kHz. With the incident pump power of 3.67 W and the PRF of 30 kHz, the highest diode-to-Stokes optical conversion efficiency of 14.9% is obtained with the corresponding average output power of 547 mW.

Femtosecond solid-state laser based on a few-layered black phosphorus saturable absorber.

PubMed

Su, Xiancui; Wang, Yiran; Zhang, Baitao; Zhao, Ruwei; Yang, Kejian; He, Jingliang; Hu, Qiangqiang; Jia, Zhitai; Tao, Xutang

2016-05-01

In this Letter, a high-quality, few-layered black phosphorus (BP) saturable absorber (SA) was fabricated successfully, and a femtosecond solid-state laser modulated by BP-SA was experimentally demonstrated for the first time, to the best of our knowledge. Pulses as short as 272 fs were achieved with an average output power of 0.82 W, corresponding to the pulse energy of 6.48 nJ and peak power of 23.8 MW. So far, these represent the shortest pulse duration and highest output power ever obtained with a BP-based mode-locked solid-state laser. The results indicate the promising potential of few-layered BP-SA for applications in solid-state femtosecond mode-locked lasers.

A novel comparator featured with input data characteristic

NASA Astrophysics Data System (ADS)

Jiang, Xiaobo; Ye, Desheng; Xu, Xiangmin; Zheng, Shuai

2016-03-01

Two types of low-power asynchronous comparators featured with input data statistical characteristic are proposed in this article. The asynchronous ripple comparator stops comparing at the first unequal bit but delivers the result to the least significant bit. The pre-stop asynchronous comparator can completely stop comparing and obtain results immediately. The proposed and contrastive comparators were implemented in SMIC 0.18 μm process with different bit widths. Simulation shows that the proposed pre-stop asynchronous comparator features the lowest power consumption, shortest average propagation delay and highest area efficiency among the comparators. Data path of low-density parity check decoder using the proposed pre-stop asynchronous comparators are most power efficient compared with other data paths with synthesised, clock gating and bitwise competition logic comparators.

Fabrication of a saturable absorber WS2 and its mode locking in solid-state laser

NASA Astrophysics Data System (ADS)

Zhang, Chun-Yu; Zhang, Ling; Tang, Xiao-Ying; Yang, Ying-Ying

2018-04-01

We report on a passively mode-locked Nd : LuVO4 laser using a type saturable absorber of tungsten disulfide (WS2) fabricated by chemical vapor deposition method. At the pump power of 3.3 W, 1.18-W average output power of continuous-wave mode-locked laser with optical conversion efficiency of 36% was achieved. To the best of our knowledge, this is the highest output power of passively mode-locked solid-state laser based on WS2. The repetition rate of passively mode-locked pulse was 80 MHz with the pulse energy of 14.8 nJ. Our experimental results show that WS2 is an excellent type of saturable absorber.

Aerosol particles generated by diesel-powered school buses at urban schools as a source of children’s exposure

PubMed Central

Hochstetler, Heather A.; Yermakov, Mikhail; Reponen, Tiina; Ryan, Patrick H.; Grinshpun, Sergey A.

2015-01-01

Various heath effects in children have been associated with exposure to traffic-related particulate matter (PM), including emissions from school buses. In this study, the indoor and outdoor aerosol at four urban elementary schools serviced by diesel-powered school buses was characterized with respect to the particle number concentrations and size distributions as well as the PM2.5 mass concentrations and elemental compositions. It was determined that the presence of school buses significantly affected the outdoor particle size distribution, specifically in the ultrafine fraction. The time-weighted average of the total number concentration measured outside the schools was significantly associated with the bus and the car counts. The concentration increase was consistently observed during the morning drop-off hours and in most of the days during the afternoon pick-up period (although at a lower degree). Outdoor PM2.5 mass concentrations measured at schools ranged from 3.8 to 27.6 µg m−3. The school with the highest number of operating buses exhibited the highest average PM2.5 mass concentration. The outdoor mass concentrations of elemental carbon (EC) and organic carbon (OC) were also highest at the school with the greatest number of buses. Most (47/55) correlations between traffic-related elements identified in the outdoor PM2.5 were significant with elements identified in the indoor PM2.5. Significant associations were observed between indoor and outdoor aerosols for EC, EC/OC, and the total particle number concentration. Day-to-day and school-to-school variations in Indoor/Outdoor (I/O) ratios were related to the observed differences in opening windows and doors, which enhanced the particle penetration, as well as indoor activities at schools. Overall, the results on I/O ratio obtained in this study reflect the sizes of particles emitted by diesel-powered school bus engines (primarily, an ultrafine fraction capable of penetrating indoors). PMID:25904818

Aerosol particles generated by diesel-powered school buses at urban schools as a source of children's exposure

NASA Astrophysics Data System (ADS)

Hochstetler, Heather A.; Yermakov, Mikhail; Reponen, Tiina; Ryan, Patrick H.; Grinshpun, Sergey A.

2011-03-01

Various heath effects in children have been associated with exposure to traffic-related particulate matter (PM), including emissions from school buses. In this study, the indoor and outdoor aerosol at four urban elementary schools serviced by diesel-powered school buses was characterized with respect to the particle number concentrations and size distributions as well as the PM2.5 mass concentrations and elemental compositions. It was determined that the presence of school buses significantly affected the outdoor particle size distribution, specifically in the ultrafine fraction. The time-weighted average of the total number concentration measured outside the schools was significantly associated with the bus and the car counts. The concentration increase was consistently observed during the morning drop-off hours and in most of the days during the afternoon pick-up period (although at a lower degree). Outdoor PM2.5 mass concentrations measured at schools ranged from 3.8 to 27.6 μg m-3. The school with the highest number of operating buses exhibited the highest average PM2.5 mass concentration. The outdoor mass concentrations of elemental carbon (EC) and organic carbon (OC) were also highest at the school with the greatest number of buses. Most (47/55) correlations between traffic-related elements identified in the outdoor PM2.5 were significant with elements identified in the indoor PM2.5. Significant associations were observed between indoor and outdoor aerosols for EC, EC/OC, and the total particle number concentration. Day-to-day and school-to-school variations in Indoor/Outdoor (I/O) ratios were related to the observed differences in opening windows and doors, which enhanced the particle penetration, as well as indoor activities at schools. Overall, the results on I/O ratio obtained in this study reflect the sizes of particles emitted by diesel-powered school bus engines (primarily, an ultrafine fraction capable of penetrating indoors).

Aerosol particles generated by diesel-powered school buses at urban schools as a source of children's exposure.

PubMed

Hochstetler, Heather A; Yermakov, Mikhail; Reponen, Tiina; Ryan, Patrick H; Grinshpun, Sergey A

2011-03-01

Various heath effects in children have been associated with exposure to traffic-related particulate matter (PM), including emissions from school buses. In this study, the indoor and outdoor aerosol at four urban elementary schools serviced by diesel-powered school buses was characterized with respect to the particle number concentrations and size distributions as well as the PM2.5 mass concentrations and elemental compositions. It was determined that the presence of school buses significantly affected the outdoor particle size distribution, specifically in the ultrafine fraction. The time-weighted average of the total number concentration measured outside the schools was significantly associated with the bus and the car counts. The concentration increase was consistently observed during the morning drop-off hours and in most of the days during the afternoon pick-up period (although at a lower degree). Outdoor PM2.5 mass concentrations measured at schools ranged from 3.8 to 27.6 µg m -3 . The school with the highest number of operating buses exhibited the highest average PM2.5 mass concentration. The outdoor mass concentrations of elemental carbon (EC) and organic carbon (OC) were also highest at the school with the greatest number of buses. Most (47/55) correlations between traffic-related elements identified in the outdoor PM2.5 were significant with elements identified in the indoor PM2.5. Significant associations were observed between indoor and outdoor aerosols for EC, EC/OC, and the total particle number concentration. Day-to-day and school-to-school variations in Indoor/Outdoor (I/O) ratios were related to the observed differences in opening windows and doors, which enhanced the particle penetration, as well as indoor activities at schools. Overall, the results on I/O ratio obtained in this study reflect the sizes of particles emitted by diesel-powered school bus engines (primarily, an ultrafine fraction capable of penetrating indoors).

Movement-related beta oscillations show high intra-individual reliability.

PubMed

Espenhahn, Svenja; de Berker, Archy O; van Wijk, Bernadette C M; Rossiter, Holly E; Ward, Nick S

2017-02-15

Oscillatory activity in the beta frequency range (15-30Hz) recorded from human sensorimotor cortex is of increasing interest as a putative biomarker of motor system function and dysfunction. Despite its increasing use in basic and clinical research, surprisingly little is known about the test-retest reliability of spectral power and peak frequency measures of beta oscillatory signals from sensorimotor cortex. Establishing that these beta measures are stable over time in healthy populations is a necessary precursor to their use in the clinic. Here, we used scalp electroencephalography (EEG) to evaluate intra-individual reliability of beta-band oscillations over six sessions, focusing on changes in beta activity during movement (Movement-Related Beta Desynchronization, MRBD) and after movement termination (Post-Movement Beta Rebound, PMBR). Subjects performed visually-cued unimanual wrist flexion and extension. We assessed Intraclass Correlation Coefficients (ICC) and between-session correlations for spectral power and peak frequency measures of movement-related and resting beta activity. Movement-related and resting beta power from both sensorimotor cortices was highly reliable across sessions. Resting beta power yielded highest reliability (average ICC=0.903), followed by MRBD (average ICC=0.886) and PMBR (average ICC=0.663). Notably, peak frequency measures yielded lower ICC values compared to the assessment of spectral power, particularly for movement-related beta activity (ICC=0.386-0.402). Our data highlight that power measures of movement-related beta oscillations are highly reliable, while corresponding peak frequency measures show greater intra-individual variability across sessions. Importantly, our finding that beta power estimates show high intra-individual reliability over time serves to validate the notion that these measures reflect meaningful individual differences that can be utilised in basic research and clinical studies. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

Experimental study of efficiency of solar panel by phase change material cooling

NASA Astrophysics Data System (ADS)

Wei, Nicholas Tan Jian; Nan, Wong Jian; Guiping, Cheng

2017-07-01

The dependence of efficiency of photovoltaic panels on their temperature during operation is a major concern for developers and users. In this paper, a phase change material (PCM) cooling system was designed for a 60W mono-crystalline solar panel. Tealights candle was selected as the cooling medium. The solar irradiance was recorded using Kipp & Zonen CMP3 pyranometer and Meteon data logger. Temperature distribution on the surface of solar panel, output voltage and output current of solar panel were measured. The average irradiance throughout data collection was found to be 705W/m2 and highest irradiance was 1100 W/m2. The average solar panel temperature was 43.6°C and a maximum temperature of 53°C was at the center of solar panel. Results showed that average power output and efficiency of the solar panel were 44.4W and 15%, respectively. It was found that the higher the solar irradiance, the lower the efficiency of solar panel and the higher the temperature and power output of solar panel. This is due to the fact that high irradiance results in high power input and high solar panel temperature. But high PV panel temperature reduces its power output. Therefore, the increase of power input outweighs that of power output, which leads to the decrease of efficiency of solar panel with the increase of solar irradiance. Compared with solar panel without cooling, the power output and efficiency of solar panel did not increase with PCM cooling. It indicates that Tealights candle as PCM cooling is not efficient in improving the efficiency of solar panel in this study.

High-power noise-like pulse generation using a 1.56-µm all-fiber laser system.

PubMed

Lin, Shih-Shian; Hwang, Sheng-Kwang; Liu, Jia-Ming

2015-07-13

We demonstrated an all-fiber, high-power noise-like pulse laser system at the 1.56-µm wavelength. A low-power noise-like pulse train generated by a ring oscillator was amplified using a two-stage amplifier, where the performance of the second-stage amplifier determined the final output power level. The optical intensity in the second-stage amplifier was managed well to avoid not only the excessive spectral broadening induced by nonlinearities but also any damage to the device. On the other hand, the power conversion efficiency of the amplifier was optimized through proper control of its pump wavelength. The pump wavelength determines the pump absorption and therefore the power conversion efficiency of the gain fiber. Through this approach, the average power of the noise-like pulse train was amplified considerably to an output of 13.1 W, resulting in a power conversion efficiency of 36.1% and a pulse energy of 0.85 µJ. To the best of our knowledge, these amplified pulses have the highest average power and pulse energy for noise-like pulses in the 1.56-µm wavelength region. As a result, the net gain in the cascaded amplifier reached 30 dB. With peak and pedestal widths of 168 fs and 61.3 ps, respectively, for the amplified pulses, the pedestal-to-peak intensity ratio of the autocorrelation trace remains at the value of 0.5 required for truly noise-like pulses.

Realization of a mW-level 10.7-eV (λ = 115.6 nm) laser by cascaded third harmonic generation of a Yb:fiber CPA laser at 1-MHz.

PubMed

Zhao, Zhigang; Kobayashi, Yohei

2017-06-12

We demonstrate a 10.7-eV (λ = 115.6 nm) laser with mW levels of average power and a 1-MHz repetition rate, which was driven by the third harmonic radiation (THG), at 347 nm, of an Yb:fiber chirped pulse amplifier (CPA) laser. The 347 nm ultraviolet radiation was obtained by frequency conversion of the high power output of a 1-MHz Yb:fiber CPA, using beta barium borate (BBO) nonlinear crystals. The frequency converted output was focused down into a gas cell filled with a mixture of Ar and Xe, and was subjected to a second THG frequency conversion. The generated 10.7-eV laser was separated from the fundamental beam using a LiF prism and no further separation from other harmonic waves was required. The highest measured output power was ~80 μW, which corresponded to an average power of ~1.25 mW inside the gas cell when the transmission coefficients of the LiF optics were taken into account. The corresponding conversion efficiency from 347 nm down to 115.6 nm was ~2.5 × 10 -4 .

The effect of low-level laser irradiation on dog spermatozoa motility is dependent on laser output power.

PubMed

Corral-Baqués, M I; Rivera, M M; Rigau, T; Rodríguez-Gil, J E; Rigau, J

2009-09-01

Biological tissues respond to low-level laser irradiation and so do dog spermatozoa. Among the main parameters to be considered when a biological tissue is irradiated is the output power. We have studied the effects on sperm motility of 655 nm continuous wave diode laser irradiation at different output powers with 3.34 J (5.97 J/cm(2)). The second fraction of fresh dog sperm was divided into five groups: control, and four to be irradiated with an average output power of 6.8 mW, 15.4 mW, 33.1 mW and 49.7 mW, respectively. At 0 min and 45 min after irradiation, pictures were taken and a computer aided sperm analysis (CASA) performed to analyse different motility parameters. The results showed that different output powers affected dog semen motility parameters differently. The highest output power showed the most intense effects. Significant changes in the structure of the motile sperm subpopulation were linked to the different output powers used.

Compact diode-pumped continuous-wave and passively Q-switched Nd:GYSO laser at 1.07 μm

NASA Astrophysics Data System (ADS)

Lin, Zhi; Huang, Xiaoxu; Lan, Jinglong; Cui, Shengwei; Wang, Yi; Xu, Bin; Luo, Zhengqian; Xu, Huiying; Cai, Zhiping; Xu, Xiaodong; Zhang, Xiaoyan; Wang, Jun; Xu, Jun

2016-08-01

We report diode-pumped continuous-wave (CW) and Q-switched Nd:GYSO lasers using a compact two-mirror linear laser cavity. Single-wavelength laser emissions at 1074.11 nm with 4.1-W power and at 1058.27 nm with 1.47-W power have been obtained in CW mode. The slope efficiencies with respect to the absorbed pump powers are 48.5% and 22.9%, respectively. Wavelength tunability is also demonstrated with range of about 8 nm. Using a MoS2 saturable absorber, maximum average output power up to 410 mW at 1074 nm can be yielded with absorbed pump power 6.41 W and the maximum pulse energy reaches 1.20 μJ with pulse repetition rate of 342.5 kHz and shortest pulse width of 810 ns. The CW laser results represent the best laser performance and the Q-switching also present the highest output power for Q-switched Nd3+ lasers with MoS2 as saturable absorber.

MW peak power Er/Yb-doped fiber femtosecond laser amplifier at 1.5 µm center wavelength

NASA Astrophysics Data System (ADS)

Han, Seongheum; Jang, Heesuk; Kim, Seungman; Kim, Young-Jin; Kim, Seung-Woo

2017-08-01

An erbium (Er)/ytterbium (Yb) co-doped double-clad fiber is configured to amplify single-mode pulses with a high average power of 10 W at a 1.5 µm center wavelength. The pulse duration at the exit of the Er/Yb fiber amplifier is measured to be ~440 fs after grating-based compression. The whole single-mode operation of the amplifier system permits the M 2-value of the output beam quality to be evaluated better than 1.05. By tuning the repetition rate from 100 MHz down to 600 kHz, the pulse peak power is scaled up to 19.1 MW to be the highest ever reported using an Er/Yb single-mode fiber. The proposed amplifier system is well suited for strong-power applications such as free-space LIDAR, non-thermal machining and medical surgery.

High power all-polarization-maintaining photonic crystal fiber monolithic femtosecond nonlinear chirped-pulse amplifier

NASA Astrophysics Data System (ADS)

Lv, Zhiguo; Yang, Zhi; Li, Feng; Yang, Xiaojun; Li, Qianglong; Zhang, Xin; Wang, Yishan; Zhao, Wei

2018-03-01

We report on an experimental study on fully fusion spliced high power all-polarization-maintaining Yb-doped photonic crystal fiber (PCF) femtosecond nonlinear chirped-pulse amplifier (CPA), which features large values of the positive third-order dispersion (TOD) superposed from the single-mode fiber stretcher (SMFs) and grating-pair compressor. Compensation of the TOD is realized by means of self-phase modulation (SPM) induced nonlinear phase shift during amplification. Up to 9.8 W of compressed average power at 275 kHz repetition rates with 36 μJ pulse energy and 495 fs pulse width has been obtained. To the best of our knowledge, this is the highest output power generated from the strictly all-fiber nonlinear CPA amplifier in femtosecond domain, which provides a possibility for the industrialized promotion and development of the high energy femtosecond fiber laser.

Advancements in high-power diode laser stacks for defense applications

NASA Astrophysics Data System (ADS)

Pandey, Rajiv; Merchen, David; Stapleton, Dean; Patterson, Steve; Kissel, Heiko; Fassbender, Wilhlem; Biesenbach, Jens

2012-06-01

This paper reports on the latest advancements in vertical high-power diode laser stacks using micro-channel coolers, which deliver the most compact footprint, power scalability and highest power/bar of any diode laser package. We present electro-optical (E-O) data on water-cooled stacks with wavelengths ranging from 7xx nm to 9xx nm and power levels of up to 5.8kW, delivered @ 200W/bar, CW mode, and a power-conversion efficiency of >60%, with both-axis collimation on a bar-to-bar pitch of 1.78mm. Also, presented is E-O data on a compact, conductively cooled, hardsoldered, stack package based on conventional CuW and AlN materials, with bar-to-bar pitch of 1.8mm, delivering average power/bar >15W operating up to 25% duty cycle, 10ms pulses @ 45C. The water-cooled stacks can be used as pump-sources for diode-pumped alkali lasers (DPALs) or for more traditional diode-pumped solid-state lasers (DPSSL). which are power/brightness scaled for directed energy weapons applications and the conductively-cooled stacks as illuminators.

An Electrochemical Capacitor with Applicable Energy Density of 7.4 Wh/kg at Average Power Density of 3000 W/kg.

PubMed

Zhai, Teng; Lu, Xihong; Wang, Hanyu; Wang, Gongming; Mathis, Tyler; Liu, Tianyu; Li, Cheng; Tong, Yexiang; Li, Yat

2015-05-13

Electrochemical capacitors represent a new class of charge storage devices that can simultaneously achieve high energy density and high power density. Previous reports have been primarily focused on the development of high performance capacitor electrodes. Although these electrodes have achieved excellent specific capacitance based on per unit mass of active materials, the gravimetric energy densities calculated based on the weight of entire capacitor device were fairly small. This is mainly due to the large mass ratio between current collector and active material. We aimed to address this issue by a 2-fold approach of minimizing the mass of current collector and increasing the electrode performance. Here we report an electrochemical capacitor using 3D graphene hollow structure as current collector, vanadium sulfide and manganese oxide as anode and cathode materials, respectively. 3D graphene hollow structure provides a lightweight and highly conductive scaffold for deposition of pseudocapacitive materials. The device achieves an excellent active material ratio of 24%. Significantly, it delivers a remarkable energy density of 7.4 Wh/kg (based on the weight of entire device) at the average power density of 3000 W/kg. This is the highest gravimetric energy density reported for asymmetric electrochemical capacitors at such a high power density.

Thermoelectric energy harvesting from diurnal heat flow in the upper soil layer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Whalen, Scott A.; Dykhuizen, Ronald C.

2012-09-26

We built and tested a subterranean thermoelectric power source that converts diurnal heat flow through the upper soil layer into electricity. This paper describes the operation, design, and performance of the device. Key features of the power source include the use of bismuth-telluride thermopiles optimized for small ΔT and aerogel insulation to minimize thermal losses. The device weighs 0.24 kg and was designed with a flat form factor measuring 12 × 12 × 1.7 cm to facilitate modularity, packing, and assembly into larger arrays. One full year of field testing was performed between June 2009 and May 2010 in Albuquerque,more » New Mexico where the device generated an average power output of 1.1 mW. The season with the highest performance was spring (March–May) while the season of lowest performance was winter (November–January). During May 2010, the device generated an average power of 1.5 mW and a peak power of 9.8 mW at 9.3 V. Ten years of continuous operation at 1.1 mW would yield an energy density and specific energy of 1384 W h/L and 1430 W h/kg respectively, which is competitive with chemical batteries and is orders of magnitude greater than published subterranean and ambient thermoelectric harvesters. Numerical simulations show that performance is sensitive to the thermal properties of the soil and environmental conditions. This class of energy harvester may provide an option for supplemental power, or possibly primary power, for low power remote sensing applications.« less

Highly efficient, versatile, self-Q-switched, high-repetition-rate microchip laser generating Ince-Gaussian modes for optical trapping

NASA Astrophysics Data System (ADS)

Dong, Jun; He, Yu; Zhou, Xiao; Bai, Shengchuang

2016-03-01

Lasers operating in the Ince-Gaussian (IG) mode have potential applications for optical manipulation of microparticles and formation of optical vortices, as well as for optical trapping and optical tweezers. Versatile, self-Q-switched, high-peak-power, high-repetition-rate Cr, Nd:YAG microchip lasers operating in the IG mode are implemented under tilted, tightly focused laser-diode pumping. An average output power of over 2 W is obtained at an absorbed pump power of 6.4 W. The highest optical-to-optical efficiency of 33.2% is achieved at an absorbed pump power of 3.9 W. Laser pulses with a pulse energy of 7.5 μJ, pulse width of 3.5 ns and peak power of over 2 kW are obtained. A repetition rate up to 335 kHz is reached at an absorbed pump power of 5.8 W. Highly efficient, versatile, IG-mode lasers with a high repetition rate and a high peak power ensure a better flexibility in particle manipulation and optical trapping.

2 µm high-power dissipative soliton resonance in a compact σ-shaped Tm-doped double-clad fiber laser

NASA Astrophysics Data System (ADS)

Du, Tuanjie; Li, Weiwei; Ruan, Qiujun; Wang, Kaijie; Chen, Nan; Luo, Zhengqian

2018-05-01

We report direct generation of a high-power, large-energy dissipative soliton resonance (DSR) in a 2 µm Tm-doped double-clad fiber laser. A compact σ-shaped cavity is formed by a fiber Bragg grating and a 10/90 fiber loop mirror (FLM). The 10/90 FLM is not only used as an output mirror, but also acts as a nonlinear optical loop mirror for initiating mode locking. The mode-locked laser can deliver high-power, nanosecond DSR pulses at 2005.9 nm. We further perform a comparison study of the effect of the FLM’s loop length on the mode-locking threshold, peak power, pulse energy, and optical spectrum of the DSR pulses. We achieve a maximum average output power as high as 1.4 W, a maximum pulse energy of 353 nJ, and a maximum peak power of 84 W. This is, to the best of our knowledge, the highest power for 2 µm DSR pulses obtained in a mode-locked fiber laser.

Highly efficient, versatile, self-Q-switched, high-repetition-rate microchip laser generating Ince–Gaussian modes for optical trapping

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jun Dong; Yu He; Xiao Zhou

2016-03-31

Lasers operating in the Ince-Gaussian (IG) mode have potential applications for optical manipulation of microparticles and formation of optical vortices, as well as for optical trapping and optical tweezers. Versatile, self-Q-switched, high-peak-power, high-repetition-rate Cr, Nd:YAG microchip lasers operating in the IG mode are implemented under tilted, tightly focused laser-diode pumping. An average output power of over 2 W is obtained at an absorbed pump power of 6.4 W. The highest optical-to-optical efficiency of 33.2% is achieved at an absorbed pump power of 3.9 W. Laser pulses with a pulse energy of 7.5 μJ, pulse width of 3.5 ns and peakmore » power of over 2 kW are obtained. A repetition rate up to 335 kHz is reached at an absorbed pump power of 5.8 W. Highly efficient, versatile, IG-mode lasers with a high repetition rate and a high peak power ensure a better flexibility in particle manipulation and optical trapping. (control of laser radiation parameters)« less

The Pine-Popple River basin--Hydrology of a wild river area, northeastern Wisconsin

USGS Publications Warehouse

Oakes, Edward L.; Field, Stephen J.; Seeger, Lawrence P.

1973-01-01

The Pine and Popple Rivers, virtually unaltered by man, flow through a semiprimitive area of forests, lakes, and glacial hills. White-water streams, natural lakes, fish and animal life, and abundant vegetation contribute to the unique recreational and aesthetic characteristics of the area. Resource planning or development should recognize the interrelationships within the hydrologic system and the possible effects of water and land-use changes upon the wild nature of the area. The basin covers about 563 square miles in northeastern Wisconsin. Swamps and wetlands cover nearly 110 square miles, and the 70 lakes cover about 11 square miles. The undulating topography is formed by glacial deposits overlying an irregular, resistant surface of bedrock. An annual average of 30 inches of precipitation, highest from late spring to early autumn, falls on the basin. Of this amount, evapotranspiration, highest in mid summer and late summer, averages 19 inches; the remaining 11 inches is runoff, which is highest in spring and early summer. Ground water from the glacial drift is the source of water for the minor withdrawal use in the basin. Ground-water movement is to streams and lakes and regionally follows the slope of topography and the bedrock surface, which is generally west to east. Ground water is of good quality, although locally high in iron. The major uses of water are for recreation and power generation. Domestic use is slight. No water is withdrawn from lakes or streams, and no sewage or industrial wastes are added to lakes or streams. Most of the flow of the Pine River is used for power generation. The main stems of the Pine and Popple Rivers contain 114 canoeable miles, of which 95 percent is without such major obstructions as falls or large rapids. In general streams support cold-water fish, and lakes support warm-water fish. Trout is the principal stream and game fish in the basin. The basin has no significant water problems. Future development between the Pine River power plant and the mouth of the Pine River should have little effect on the western two-thirds of the basin, already largely protected by public ownership or development planning agreements.

Retrospective exposure assessment to airborne asbestos among power industry workers

PubMed Central

2010-01-01

Background A method of individually assessing former exposure to asbestos fibres is a precondition of risk-differentiated health surveillance. The main aims of our study were to assess former levels of airborne asbestos exposure in the power industry in Germany and to propose a basic strategy for health surveillance and the early detection of asbestos related diseases. Methods Between March 2002 and the end of 2006, we conducted a retrospective questionnaire based survey of occupational tasks and exposures with airborne asbestos fibres in a cohort of 8632 formerly asbestos exposed power industry workers. The data on exposure and occupation were entered into a specially designed computer programme, based on ambient monitoring of airborne asbestos fibre concentrations. The cumulative asbestos exposure was expressed as the product of the eight-hour time weighted average and the total duration of exposure in fibre years (fibres/cubic centimetre-years). Results Data of 7775 (90% of the total) participants working in installations for power generation, power distribution or gas supply could be evaluated. The power generation group (n = 5284) had a mean age of 56 years, were exposed for 20 years and had an average cumulative asbestos exposure of 42 fibre years. The occupational group of "metalworkers" (n = 1600) had the highest mean value of 79 fibre years. The corresponding results for the power distribution group (n = 2491) were a mean age of 45 years, a mean exposure duration of 12 years and an average cumulative asbestos exposure of only 2.5 fibre years. The gas supply workers (n = 512) had a mean age of 54 years and a mean duration of exposure of 15 years. Conclusions While the surveyed cohort as a whole was heavily exposed to asbestos dust, the power distribution group had a mean cumulative exposure of only 6% of that found in the power generation group. Based on the presented data, risk-differentiated disease surveillance focusing on metalworkers and electricians from the power generating industry seems justified. That combined with a sensitive examination technique would allow detecting asbestos related diseases early and efficiently. PMID:20579364

Characteristics and distributions of atmospheric mercury ...

EPA Pesticide Factsheets

Continuous measurements of speciated atmospheric mercury (Hg), including gaseous elemental mercury (GEM), particulate mercury (PHg), and reactive gaseous mercury (RGM) were conducted in Guizhou Province, southwestern China. Guiyang Power Plant (GPP), Guiyang Wujiang Cement Plant, Guizhou Aluminum Plant (GAP), and Guiyang Forest Park (GFP) in Guiyang were selected as study sites. Automatic Atmospheric Mercury Speciation Analyzers (Tekran 2537A) were used for GEM analysis. PHg and RGM were simultaneously collected by a manual sampling system, including elutriator, coupler/impactor, KCl-coated annular denuder, and a filter holder. Results show that different emission sources dominate different species of Hg. The highest average GEM value was 22.2 ± 28.3 ng·m−3 and the lowest 6.1 ± 3.9 ng·m−3, from samples collected at GPP and GAP, respectively. The maximum average PHg was 1984.9 pg·m−3 and the minimum average 55.9 pg·m−3, also from GPP and GAP, respectively. Similarly, the highest average RGM of 68.8 pg·m−3 was measured at GPP, and the lowest level of 20.5 pg·m−3 was found at GAP. We conclude that coal combustion sources are still playing a key role in GEM; traffic contributes significantly to PHg; and domestic pollution dominates RGM. Mercury (Hg) is a persistent hazardous pollutant with adverse effects on human health and wildlife due mainly to bioaccumulation and biomagnification in aquatic food webs (Lindqvist et al. 1991; Schroeder and Munt

White syndrome on massive corals: A case study in Paiton power plant, East Java

NASA Astrophysics Data System (ADS)

Muzaki, Farid Kamal; Saptarini, Dian; Riznawati, Aida Efrini

2017-06-01

As a stenothermal organism, coral easily affected by high-temperature cooling water discharged by a power plant into surrounding waters; which may lead to a rapid spread and transmission of coral disease, including White Syndrome. This study aimed to measure the prevalence of WS on massive corals in Paiton Power Plant waters. Research was conductedduring May 2015 at three observation stations; west and east side of water discharge canal (DB and DT) and water intake canal (WI). Observed parameters including ambient environmental variables (sea surface and bottom temperature, salinity, dissolved oxygen/DO, pH, and visibility); the cover of life corals (percent and genera composition) and prevalence of coral disease at 5 m depth. One-way ANOVA (analysis of variance, p=0.05) was performed to test the difference of coral disease prevalence from different observation stations. As the results, Coral coverage percentage in WI (85.75%), DB (60.75%), and DT (40.8%). Prevalence of WS in DB was highest (40.49±2.12% in DB, 13.53±11.5% in DT and 6.44±3.6 %, respectively). It can be assumed that prevalence of White Syndrome in those locations may be correlated to temperature which highest average temperature occurred in DB stations.

Water-soluble ions in atmospheric aerosols measured in Xi'an, China: Seasonal variations and sources

NASA Astrophysics Data System (ADS)

Zhang, T.; Cao, J. J.; Tie, X. X.; Shen, Z. X.; Liu, S. X.; Ding, H.; Han, Y. M.; Wang, G. H.; Ho, K. F.; Qiang, J.; Li, W. T.

2011-10-01

Daily PM 2.5 and water-soluble inorganic ions (Na +, NH 4+, K +, Mg 2+, Ca 2+, Cl -, NO 3- and SO 42-) were collected in Xi'an (34.23°N, 108.88°E), China from March 2006 to March 2007. PM 2.5 was collected using battery-powered mini-volume samplers. And the ions were determined by ion chromatography from the measured aerosol mass. The annual average mass concentration of PM 2.5 was found to be 194.1 ± 78.6 μg m - 3 , which exceeded substantially the international guidelines for health concerns. The seasonal average mass concentration of PM 2.5 was highest in winter (266.8 μg m - 3 ) and lowest in summer (138.6 μg m - 3 ). The three highest abundant ions were SO 42-, NO 3-, and NH 4+, with average concentrations of 35.6 ± 19.5 μg m - 3 , 16.4 ± 10.1 μg m - 3 , and 11.4 ± 6.8 μg m - 3 , which were accounted for 18.7%, 8.0%, and 5.7% of the PM 2.5 mass, respectively. The major ions were in the species of (NH 4) 2SO 4, NH 4HSO 4 and NH 4NO 3, and their concentrations were highest in winter, due to high coal combustion. The concentrations of Ca 2+ were higher in spring than other seasons, due to the higher mineral dust concentrations. Ca 2+ was strongly correlated with CO 32-, which was calculated as the difference in the measured cations minus anions. Ion balance calculations indicate that the PM 2.5 was acidic, and this result is consistent with the measurement of pH values. Sulfur oxidation ratio was higher in summer and autumn, which implies that the formation of secondary sulfate-rich particles is favored by warm and relatively moist weather. Nitrogen oxidation ratio was highest in autumn.

Evaluation of Dynamic Channel and Power Assignment for Cognitive Networks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Syed A. Ahmad; Umesh Shukla; Ryan E. Irwin

2011-03-01

In this paper, we develop a unifying optimization formulation to describe the Dynamic Channel and Power Assignment (DCPA) problem and evaluation method for comparing DCPA algorithms. DCPA refers to the allocation of transmit power and frequency channels to links in a cognitive network so as to maximize the total number of feasible links while minimizing the aggregate transmit power. We apply our evaluation method to five algorithms representative of DCPA used in literature. This comparison illustrates the tradeoffs between control modes (centralized versus distributed) and channel/power assignment techniques. We estimate the complexity of each algorithm. Through simulations, we evaluate themore » effectiveness of the algorithms in achieving feasible link allocations in the network, as well as their power efficiency. Our results indicate that, when few channels are available, the effectiveness of all algorithms is comparable and thus the one with smallest complexity should be selected. The Least Interfering Channel and Iterative Power Assignment (LICIPA) algorithm does not require cross-link gain information, has the overall lowest run time, and highest feasibility ratio of all the distributed algorithms; however, this comes at a cost of higher average power per link.« less

Global Positioning System Use in the Community to Evaluate Improvements in Walking After Revascularization

PubMed Central

Gernigon, Marie; Le Faucheur, Alexis; Fradin, Dominique; Noury-Desvaux, Bénédicte; Landron, Cédric; Mahe, Guillaume; Abraham, Pierre

2015-01-01

Abstract Revascularization aims at improving walking ability in patients with arterial claudication. The highest measured distance between 2 stops (highest-MDCW), the average walking speed (average-WSCW), and the average stop duration (average-DSCW) can be measured by global positioning system, but their evolution after revascularization is unknown. We included 251 peripheral artery diseased patients with self-reported limiting claudication. The patients performed a 1-hour stroll, recorded by a global positioning system receiver. Patients (n = 172) with confirmed limitation (highest-MDCW <2000m) at inclusion were reevaluated after 6 months. Patients revascularized during the follow-up period were compared with reference patients (ie, with unchanged lifestyle medical or surgical status). Other patients (lost to follow-up or treatment change) were excluded (n = 89). We studied 44 revascularized and 39 reference patients. Changes in highest-MDCW (+442 vs. +13 m) and average-WSCW (+0.3 vs. −0.2 km h−1) were greater in revascularized than in reference patients (both P < 0.01). In contrast, no significant difference in average-DSCW changes was found between the groups. Among the revascularized patients, 13 (29.5%) had a change in average-WSCW, but not in highest-MDCW, greater than the mean + 1 standard deviation of the change observed for reference patients. Revascularization may improve highest-MDCW and/or average-WSCW. This first report of changes in community walking ability in revascularized patients suggests that, beyond measuring walking distances, average-WSCW measurement is essential to monitor these changes. Applicability to other surgical populations remains to be evaluated. Registration: http://www.clinicaltrials.gov/ct2/show/NCT01141361 PMID:25950694

Global positioning system use in the community to evaluate improvements in walking after revascularization: a prospective multicenter study with 6-month follow-up in patients with peripheral arterial disease.

PubMed

Gernigon, Marie; Le Faucheur, Alexis; Fradin, Dominique; Noury-Desvaux, Bénédicte; Landron, Cédric; Mahe, Guillaume; Abraham, Pierre

2015-05-01

Revascularization aims at improving walking ability in patients with arterial claudication. The highest measured distance between 2 stops (highest-MDCW), the average walking speed (average-WSCW), and the average stop duration (average-DSCW) can be measured by global positioning system, but their evolution after revascularization is unknown.We included 251 peripheral artery diseased patients with self-reported limiting claudication. The patients performed a 1-hour stroll, recorded by a global positioning system receiver. Patients (n = 172) with confirmed limitation (highest-MDCW <2000m) at inclusion were reevaluated after 6 months. Patients revascularized during the follow-up period were compared with reference patients (ie, with unchanged lifestyle medical or surgical status). Other patients (lost to follow-up or treatment change) were excluded (n = 89).We studied 44 revascularized and 39 reference patients. Changes in highest-MDCW (+442 vs. +13 m) and average-WSCW (+0.3 vs. -0.2 km h) were greater in revascularized than in reference patients (both P < 0.01). In contrast, no significant difference in average-DSCW changes was found between the groups. Among the revascularized patients, 13 (29.5%) had a change in average-WSCW, but not in highest-MDCW, greater than the mean + 1 standard deviation of the change observed for reference patients.Revascularization may improve highest-MDCW and/or average-WSCW. This first report of changes in community walking ability in revascularized patients suggests that, beyond measuring walking distances, average-WSCW measurement is essential to monitor these changes. Applicability to other surgical populations remains to be evaluated. http://www.clinicaltrials.gov/ct2/show/NCT01141361.

A diode-pumped Tm:CaYAlO4 laser at 1851 nm

NASA Astrophysics Data System (ADS)

Lan, Jinglong; Guan, Xiaofeng; Xu, Bin; Moncorgé, Richard; Xu, Huiying; Cai, Zhiping

2017-07-01

Laser emission at ~1850 nm is of great interest for neural stimulation applications. In this letter, we report on the diode-pumped continuous-wave (CW) and Q-switched (QS) laser operation of Tm:CaYAlO4 at 1851 nm, for the first time to our knowledge. In the CW regime, a maximum output power up to 0.62 W is obtained with a laser slope efficiency of about 18.0%. Using a Cr:ZnSe saturable absorber, QS laser operation is achieved with a maximum average output power of 0.25 W, the narrowest pulse width of 107 ns and the highest repetition rate of 5.85 kHz. The corresponding pulse peak power and pulse energy are about 388 W and 42.8 µJ, respectively. In this Q-switched mode, wavelength tuning is also realized over about 3 nm by slightly tilting the saturable absorber.

Direct growth of graphene on quartz substrate as saturable absorber for femtosecond solid-state laser

NASA Astrophysics Data System (ADS)

Xu, S. C.; Man, B. Y.; Jiang, S. Z.; Chen, C. S.; Liu, M.; Yang, C.; Gao, S. B.; Feng, D. J.; Hu, G. D.; Huang, Q. J.; Chen, X. F.; Zhang, C.

2014-08-01

We present a novel method for the direct metal-free growth of graphene on quartz substrate. The direct-grown graphene yields excellent nonlinear saturable absorption properties and is demonstrated to be suitable as a saturable absorber (SA) for an ultrafast solid-state laser. Nearly Fourier-limited 367 fs was obtained at a central wavelength of 1048 nm with a repetition rate of 105.7 MHz. At a pump power of 7.95 W, the average output power was 1.93 W and the highest pulse energy reached 18.3 nJ, with a peak power of 49.8 kW. Our work opens an easy route for making a reliable graphene SA with a mode-locking technique and also displays an exciting prospect in making low-cost and ultrafast lasers.

Double Q-switch Ho:Sc2SiO5 laser by acousto-optic modulator combined with Cr2+:ZnSe saturable absorber

NASA Astrophysics Data System (ADS)

Yang, Xiao-tao; Zhang, Peng; Xie, Wen-qiang; Li, Lin-jun

2018-01-01

A double Q-switch (DQS) Ho:Sc2SiO5 laser modulated by a acousto-optic modulators (AOM) combined with a Cr2+:ZnSe saturable absorber (SA) was reported for the first time. The actively Q-switch (AQS) and passively Q-switch (PQS) were also studied. For the DQS mode, a maximum average output power of 2.49 W under the incident pump power of 12.5 W was obtained, corresponding to a slope efficiency of 24%. The characteristics of the DQS Ho:SSO laser versus different repetition frequencies (RF) of the AOM were researched. The maximum single-pulse energy of the DQS Ho:SSO laser was calculated to 1.98 mJ. The maximum peak power of the DQS Ho:SSO laser was 49.5 kW. The output beam quality factor M2 of DQS Ho:SSO laser was measured to be 1.15 with the highest peak power by knife-edge method at different positions.

S – C – L triple wavelength superluminescent source based on an ultra-wideband SOA and FBGs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ahmad, H; Zulkifli, M Z; Hassan, N A

2013-10-31

We propose and demonstrate a wide-band semiconductor optical amplifier (SOA) based triple-wavelength superluminescent source with the output in the S-, C- and L-band regions. The proposed systems uses an ultra-wideband SOA with an amplification range from 1440 to 1620 nm as the linear gain medium. Three fibre Bragg gratings (FBGs) with centre wavelengths of 1500, 1540 and 1580 nm are used to generate the lasing wavelengths in the S-, Cand L-bands respectively, while a variable optical attenuator is used to finely balance the optical powers of the lasing wavelengths. The ultra-wideband SOA generates an amplified spontaneous emission (ASE) spectrum withmore » a peak power of -33 dBm at the highest SOA drive current, and also demonstrates a down-shift in the centre wavelength of the generated spectrum due to the spatial distribution of the carrier densities. The S-band wavelength is the dominant wavelength at high drive currents, with an output power of -6 dBm as compared to the C- and L-bands, which only have powers of -11 and -10 dBm, respectively. All wavelengths have a high average signal-to-noise ratio more than 60 dB at the highest drive current of 390 mA, and the system also shows a high degree of stability, with power fluctuations of less than 3 dB within 70 min. The proposed system can find many applications where a wide-band and stable laser source is crucial, such as in communications and sensing. (control of laser radiation parameters)« less

Performance study of highly efficient 520 W average power long pulse ceramic Nd:YAG rod laser

NASA Astrophysics Data System (ADS)

Choubey, Ambar; Vishwakarma, S. C.; Ali, Sabir; Jain, R. K.; Upadhyaya, B. N.; Oak, S. M.

2013-10-01

We report the performance study of a 2% atomic doped ceramic Nd:YAG rod for long pulse laser operation in the millisecond regime with pulse duration in the range of 0.5-20 ms. A maximum average output power of 520 W with 180 J maximum pulse energy has been achieved with a slope efficiency of 5.4% using a dual rod configuration, which is the highest for typical lamp pumped ceramic Nd:YAG lasers. The laser output characteristics of the ceramic Nd:YAG rod were revealed to be nearly equivalent or superior to those of high-quality single crystal Nd:YAG rod. The laser pump chamber and resonator were designed and optimized to achieve a high efficiency and good beam quality with a beam parameter product of 16 mm mrad (M2˜47). The laser output beam was efficiently coupled through a 400 μm core diameter optical fiber with 90% overall transmission efficiency. This ceramic Nd:YAG laser will be useful for various material processing applications in industry.

Shock waves on complex networks

NASA Astrophysics Data System (ADS)

Mones, Enys; Araújo, Nuno A. M.; Vicsek, Tamás; Herrmann, Hans J.

2014-05-01

Power grids, road maps, and river streams are examples of infrastructural networks which are highly vulnerable to external perturbations. An abrupt local change of load (voltage, traffic density, or water level) might propagate in a cascading way and affect a significant fraction of the network. Almost discontinuous perturbations can be modeled by shock waves which can eventually interfere constructively and endanger the normal functionality of the infrastructure. We study their dynamics by solving the Burgers equation under random perturbations on several real and artificial directed graphs. Even for graphs with a narrow distribution of node properties (e.g., degree or betweenness), a steady state is reached exhibiting a heterogeneous load distribution, having a difference of one order of magnitude between the highest and average loads. Unexpectedly we find for the European power grid and for finite Watts-Strogatz networks a broad pronounced bimodal distribution for the loads. To identify the most vulnerable nodes, we introduce the concept of node-basin size, a purely topological property which we show to be strongly correlated to the average load of a node.

Laser fiber cleaving techniques: effects on tip morphology and power output.

PubMed

Vassantachart, Janna M; Lightfoot, Michelle; Yeo, Alexander; Maldonado, Jonathan; Li, Roger; Alsyouf, Muhannad; Martin, Jacob; Lee, Michael; Olgin, Gaudencio; Baldwin, D Duane

2015-01-01

Proper cleaving of reusable laser fibers is needed to maintain optimal functionality. This study quantifies the effect of different cleaving tools on power output of the holmium laser fiber and demonstrates morphologic changes using microscopy. The uncleaved tips of new 272 μm reusable laser fibers were used to obtain baseline power transmission values at 3 W (0.6 J, 5 Hz). Power output for each of four cleaving techniques-11-blade scalpel, scribe pen cleaving tool, diamond cleaving wheel, and suture scissors-was measured in a single-blinded fashion. Dispersion of light from the fibers was compared with manufacturer specifications and rated as "ideal," "acceptable," or "unacceptable" by blinded reviewers. The fiber tips were also imaged using confocal and scanning electron microscopy. Independent samples Kruskal-Wallis test and chi square were used for statistical analysis (α<0.05). New uncleaved fiber tips transmitted 3.04 W of power and were used as a reference (100%). The scribe pen cleaving tool produced the next highest output (97.1%), followed by the scalpel (83.4%), diamond cleaving wheel (77.1%), and suture scissors (61.7%), a trend that was highly significant (P<0.001). On pairwise comparison, no difference in power output was seen between the uncleaved fiber tips and those cleaved with the scribe pen (P=1.0). The rating of the light dispersion patterns from the different cleaving methods followed the same trend as the power output results (P<0.001). Microscopy showed that the scribe pen produced small defects along the fiber cladding but maintained a smooth, flat core surface. The other cleaving techniques produced defects on both the core and cladding. Cleaving techniques produce a significant effect on the initial power transmitted by reusable laser fibers. The scribe pen cleaving tool produced the most consistent and highest average power output.

1.2 MW peak power, all-solid-state picosecond laser with a microchip laser seed and a high gain single-passing bounce geometry amplifier

NASA Astrophysics Data System (ADS)

Wang, Chunhua; Shen, Lifeng; Zhao, Zhiliang; Liu, Bin; Jiang, Hongbo; Chen, Jun; Liu, Chong

2016-11-01

A semiconductor saturable absorber mirror (SESAM) based passively Q-switched microchip Nd:YVO4 seed laser with pulse duration of 90 ps at repetition rate of 100 kHz is amplified by single-passing a Nd:YVO4 bounce amplifier with varying seed input power from 20 μW to 10 mW. The liquid pure metal greasy thermally conductive material is used to replace the traditional thin indium foil as the thermal contact material for better heat load transfer of the Nd:YVO4 bounce amplifier. Temperature distribution at the pump surface is measured by an infrared imager to compare with the numerically simulated results. A highest single-passing output power of 11.3 W is obtained for 10 mW averaged seed power, achieving a pulse peak power of ~1.25 MW and pulse energy of ~113 μJ. The beam quality is well preserved with M2 ≤1.25. The simple configuration of this bounce laser amplifier made the system flexible, robust and cost-effective, showing attractive potential for further applications.

Defining and measuring cyberbullying within the larger context of bullying victimization

PubMed Central

Ybarra, Michele; boyd, danah; Korchmaros, Josephine; Oppenheim, Jay (Koby)

2012-01-01

Methods Two split-form surveys were conducted online among 6–17 year olds (n=1,200 each) to inform recommendations for cyberbullying measurement. Results Measures that use the word ‘bully’ result in prevalence rates similar to each other whether or not a definition is included, whereas measures not using the word ‘bully’ are similar to each other whether or not a definition is included. A behavioral list of bullying experiences without either a definition or the word ‘bully’ results in higher prevalence rates and likely measures experiences that are beyond the definition of ‘bullying’. Follow-up questions querying differential power, repetition, and bullying over time were used to examine misclassification. The measure using a definition but not the word ‘bully’ appeared to have the highest rate of false positives and, therefore, the highest rate of misclassification. Across two studies, an average of 25% reported being bullied at least monthly in person compared with an average of 10% bullied online, 7% via telephone (cell or landline), and 8% via text messaging. Conclusions Measures of bullying among English-speaking samples in the US should include the word ‘bully’ when possible. The definition may be a useful tool for researchers, but results suggest that it does not necessarily yield a more rigorous measure of bullying victimization. Directly measuring aspects of bullying (i.e., differential power, repetition, over time) reduces misclassification. To prevent double counting across categories, we conceptualize cyberbullying as bullying communicated through the online mode; type (e.g., verbal, relational), and environment (e.g., school, home) are additional domains of bullying. PMID:22727077

40 CFR 60.58b - Compliance and performance testing.

Code of Federal Regulations, 2010 CFR

2010-07-01

... demonstrated municipal waste combustor unit load shall be the highest 4-hour arithmetic average load achieved... shall be the highest 4-hour arithmetic average temperature achieved at the particulate matter control...

Local Impacts of Mercury Emissions from the Three Pennsylvania Coal Fired Power Plants.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sullivan,T.; Adams,J.; Bender, M.

2008-02-01

The Clean Air Interstate Rule (CAIR) and the Clean Air Mercury Rule (CAMR) as proposed by the U.S. Environmental Protection Agency (EPA) when fully implemented will lead to reduction in mercury emissions from coal-fired power plants by 70 percent to fifteen tons per year by 2018. The EPA estimates that mercury deposition would be reduced 8 percent on average in the Eastern United States. The CAMR permits cap-and-trade approach that requires the nationwide emissions to meet the prescribed level, but do not require controls on each individual power plant. This has led to concerns that there may be hot-spots ofmore » mercury contamination near power plants. Partially because of this concern, many states including Pennsylvania have implemented, or are considering, state regulations that are stricter on mercury emissions than those in the CAMR. This study examined the possibility that coal-fired power plants act as local sources leading to mercury 'hot spots'. Soil and oak leaf samples from around three large U.S. coal-fired power plants in Western Pennsylvania were collected and analyzed for evidence of 'hot spots'. These three plants (Conemaugh, Homer City, and Keystone) are separated by a total distance of approximately 30 miles. Each emits over 500 pounds of mercury per year which is well above average for mercury emissions from coal plants in the U.S. Soil and oak leaf sampling programs were performed around each power plant. Sampling rings one-mile apart were used with eight or nine locations on each ring. The prevailing winds in the region are from the west. For this reason, sampling was conducted out to 10 miles from the Conemaugh plant which is southeast of the others. The other plants were sampled to a distance of five miles. The objectives were to determine if local mercury hot spots exist, to determine if they could be attributed to deposition of coal-fired power plant emissions, and to determine if they correlated with wind patterns. The study found the following: (1) There was some correlation between the prevailing wind direction and measured soil and oak leaf concentrations. This correlation was not statistically significant, but higher soil concentrations were generally found in the east and southeast from the plants and lower soil concentrations were found west/southwest from the plants. The prevailing winds are to the east. The Conemaugh plant which was the most southeast of the three plants did have the highest average oak leaf and soil mercury concentrations. Based on emissions, the Keystone plant would be expected to see the highest concentrations as it emitted about 25% more mercury than the other two plants. (2) The results of this study did not turn up strong evidence for large areas (several square miles) of elevated mercury concentrations around the three coal-fired power plants that were tested. This does not mean that there is no effect, there was some evidence of increasing mercury content to the east and south of these plants, however, the trends were not statistically significant suggesting that if the effects exist, they are small.« less

The region makes the difference: disparities in management of acute myocardial infarction within Switzerland.

PubMed

Insam, Charlène; Paccaud, Fred; Marques-Vidal, Pedro

2014-05-01

In Switzerland, health policies are decided at the local level, but little is known regarding their impact on the management of acute myocardial infarction (AMI). In this study, we assessed geographical differences within Switzerland regarding management of AMI. Cross-sectional study. Swiss hospital discharge database for period 2007-2008 (26,204 discharges from AMI). Seven Swiss regions (Leman, Mittelland, Northwest, Zurich, Central, Eastern, and Ticino) were analysed. Almost 53.7% of discharges from AMI were managed in a single hospital, ranging from 62.1% (Leman) to 31.6% (Ticino). The highest intensive care unit admission rate was in Leman (69.4%), the lowest (16.9%) in Ticino (Swiss average: 36.0%). Intracoronary revascularization rates were highest in Leman (51.1%) and lowest (30.9%) in Central Switzerland (average: 41.0%). Bare (non-drug-eluting) stent use was highest in Leman (61.4%) and lowest (16.9%) in Ticino (average: 42.1%), while drug-eluting stent use was highest (83.2%) in Ticino and lowest (38.6%) in Leman (average: 57.9%). Coronary artery bypass graft rates were highest (4.8%) in Ticino and lowest (0.5%) in Eastern Switzerland (average: 2.8%). Mechanical circulatory assistance rates were highest (4.2%) in Zurich and lowest (0.5%) in Ticino (average: 1.8%). The differences remained after adjusting for age, single or multiple hospital management, and gender. In Switzerland, significant geographical differences in management and revascularization procedures for AMI were found.

Improving optical properties of silicon nitride films to be applied in the middle infrared optics by a combined high-power impulse/unbalanced magnetron sputtering deposition technique.

PubMed

Liao, Bo-Huei; Hsiao, Chien-Nan

2014-02-01

Silicon nitride films are prepared by a combined high-power impulse/unbalanced magnetron sputtering (HIPIMS/UBMS) deposition technique. Different unbalance coefficients and pulse on/off ratios are applied to improve the optical properties of the silicon nitride films. The refractive indices of the Si3N4 films vary from 2.17 to 2.02 in the wavelength ranges of 400-700 nm, and all the extinction coefficients are smaller than 1×10(-4). The Fourier transform infrared spectroscopy and x-ray diffractometry measurements reveal the amorphous structure of the Si3N4 films with extremely low hydrogen content and very low absorption between the near IR and middle IR ranges. Compared to other deposition techniques, Si3N4 films deposited by the combined HIPIMS/UBMS deposition technique possess the highest refractive index, the lowest extinction coefficient, and excellent structural properties. Finally a four-layer coating is deposited on both sides of a silicon substrate. The average transmittance from 3200 to 4800 nm is 99.0%, and the highest transmittance is 99.97% around 4200 nm.

Effect of Cr3+ substitution on AC susceptibility of Ba hexaferrite nanoparticles

NASA Astrophysics Data System (ADS)

Slimani, Y.; Baykal, A.; Manikandan, A.

2018-07-01

In this study, nano-sized particles of BaCrxFe12-xO19 (0.0 ≤ x ≤ 1.0) hexaferrite were fabricated through citrate auto gel combustion process and the impact of Cr-ion substitution on ac magnetic susceptibility properties of Ba-hexaferrite were explored. X-ray powder diffraction (XRD) measurements approved the purity of prepared samples and showed a reduction of the average crystallite size with increasing the content of Cr. Transmission electron microscopy (TEM) observation indicated the hexagonal morphology of all samples. AC susceptibility measurements displayed a frequency dependence of the magnetic responses. These measurements indicated that there are strong magnetic interactions (which is the highest for BaCr0.3Fe11.7O19 NP) between particles which cause a superspin glass-like (SSG) behavior at low temperatures. Estimating the values of loss power density revealed an increase of loss power density with increasing Cr-substitution element. The relative sensitivity of the prepared MNPs to the variation of applied frequency is very influenced by Cr-substitution and is highest in BaCr0.3Fe11.7O19 MNPs, suggesting that this sample can be considered as magnetic nanomaterial for hyperthermia and for many other applications.

AIRBORNE MICROORGANISMS IN BROILER PROCESSING PLANTS.

PubMed

KOTULA, A W; KINNER, J A

1964-05-01

Concentrations of total aerobic bacteria, molds, yeasts, coliforms, enterococci, and psychrophiles were determined in the air of two poultry processing plants with Andersen samplers and a mobile power supply. Total aerobic bacterial counts were highest in the dressing room, with diminishing numbers in the shackling, eviscerating, and holding rooms, when sampling was carried out during plant operation. The average counts per ft(3) of air in these four rooms were 2,200; 560; 230; and 62, respectively. (Each value is the average of 36 observations.) The number of organisms increased in the shackling and dressing rooms once processing was begun. Average total aerobic bacterial counts increased from 70 to 870 to 3,000 in the shackling room and from 310 to 4,900 to 7,000 in the dressing room when sampling was carried out at 5:00 am (before plant operations), 9:00 am, and 2:00 pm, respectively. (Each value is the mean of 12 observations.) Airborne molds might originate from a source other than the poultry being processed.

Airborne Microorganisms in Broiler Processing Plants

PubMed Central

Kotula, Anthony W.; Kinner, Jack A.

1964-01-01

Concentrations of total aerobic bacteria, molds, yeasts, coliforms, enterococci, and psychrophiles were determined in the air of two poultry processing plants with Andersen samplers and a mobile power supply. Total aerobic bacterial counts were highest in the dressing room, with diminishing numbers in the shackling, eviscerating, and holding rooms, when sampling was carried out during plant operation. The average counts per ft3 of air in these four rooms were 2,200; 560; 230; and 62, respectively. (Each value is the average of 36 observations.) The number of organisms increased in the shackling and dressing rooms once processing was begun. Average total aerobic bacterial counts increased from 70 to 870 to 3,000 in the shackling room and from 310 to 4,900 to 7,000 in the dressing room when sampling was carried out at 5:00 am (before plant operations), 9:00 am, and 2:00 pm, respectively. (Each value is the mean of 12 observations.) Airborne molds might originate from a source other than the poultry being processed. Images FIG. 3 PMID:14170951

Improved lifetime of chitosan film in converting water vapor to electrical power by adding carboxymethyl cellulose

NASA Astrophysics Data System (ADS)

Nasution, T. I.; Balyan, M.; Nainggolan, I.

2018-02-01

A Water vapor cell based on chitosan film has been successfully fabricated in film form to convert water vapor to electrical power. In order to improve the lifetime of water vapor cell, Carboxymethyl Cellulose (CMC) was added into 1% chitosan solution within concentration variations of 0.01, 0.05, 0.1 and 0.5%. The result showed that the lifetime of water vapor cell increased higher by adding the higher concentration of Carboxymethyl cellulose. The highest lifetime was evidenced by adding 0.5%CMC which maintained for 48 weeks. However, the average electrical power became lower to 4.621 µW. This electrical power lower than the addition of 0.1%CMC which maintained for 5.167 µW. While, the lifetime of chitosan-0.1%CMC film of 44 weeks is shorter compared to chitosan-0.5%CMC film. Based on FTIR characterization, it was founded that the chitosan structure did not change until the addition of 0.1%CMC. This caused the electrical power of water vapor cell degenerated. Therefore, chitosan-0.5%CMC film has excellent lifetime in converting water vapor to electrical power.

Resonantly diode-pumped continuous-wave and Q-switched Er:YAG laser at 1645 nm.

PubMed

Chang, N W H; Simakov, N; Hosken, D J; Munch, J; Ottaway, D J; Veitch, P J

2010-06-21

We describe an efficient Er:YAG laser that is resonantly pumped using continuous-wave (CW) laser diodes at 1470 nm. For CW lasing, it emits 6.1 W at 1645 nm with a slope efficiency of 36%, the highest efficiency reported for an Er:YAG laser that is pumped in this manner. In Q-switched operation, the laser produces diffraction-limited pulses with an average power of 2.5 W at 2 kHz PRF. To our knowledge this is the first Q-switched Er:YAG laser resonantly pumped by CW laser diodes.

Vibration characteristics of OH-58A helicopter main rotor transmission

NASA Technical Reports Server (NTRS)

Lewicki, David G.; Coy, John J.

1987-01-01

Experimental vibration tests covering a range of torque and speed conditions were performed on the OH-58A helicopter main rotor transmission at the NASA Lewis Research Center. Signals from accelerometers located on the transmission housing were analyzed by using Fourier spectra, power spectral density functions, and averaging techniques. Most peaks of the Fourier spectra occurred at the spiral bevel and planetary gear mesh harmonics. The highest level of vibration occurred at the spiral bevel meshing frequency. Transmission speed and vibration measurement location had a significant effect on measured vibration; transmission torque and measurement direction had a small effect.

Physical fitness, injuries, and team performance in soccer.

PubMed

Arnason, Arni; Sigurdsson, Stefan B; Gudmundsson, Arni; Holme, Ingar; Engebretsen, Lars; Bahr, Roald

2004-02-01

To investigate the relationship between physical fitness and team success in soccer, and to test for differences in physical fitness between different player positions. Participants were 306 male soccer players from 17 teams in the two highest divisions in Iceland. Just before the start of the 1999 soccer season, the following variables were tested: height and weight, body composition, flexibility, leg extension power, jump height, and peak O2 uptake. Injuries and player participation in matches and training were recorded through the 4-month competitive season. Team average physical fitness was compared with team success (final league standing) using a linear regression model. Physical fitness was also compared between players in different playing positions. A significant relationship was found between team average jump height (countermovement jump and standing jump) and team success (P = 0.009 and P = 0.012, respectively). The same trend was also found for leg extension power (P = 0.097), body composition (% body fat, P = 0.07), and the total number of injury days per team (P = 0.09). Goalkeepers demonstrated different fitness characteristics from outfield players. They were taller and heavier, more flexible in hip extension and knee flexion, and had higher leg extension power and a lower peak O2 uptake. However, only minor differences were observed between defenders, midfield players, and attackers. Coaches and medical support teams should pay more attention to jump and power training, as well as preventive measures and adequate rehabilitation of previous injuries to increase team success.

Temperature and water-quality conditions of the Patuxent River estuary, Maryland, January 1966 through December 1967

USGS Publications Warehouse

Cory, Robert L.; Nauman, Jon W.

1970-01-01

The effect of power plant cooling water in raising natural water temperatures at a location near the power plant on the Patuxent River estuary is clearly evident from thermograph records. Surface temperature at a station 333 m (1,000 ft) downstream from the discharge canal was raised an average of about 4 C, and at times by as much as 8 C. Temperature rises were greatest during the winter. Infrared imagery showed that elevated surface temperatures could be detected about 5.5 km (3 nautical miles) upstream at flood tide. Temperature profiles obtained from airborne radiation equipment revealed a complicated surface temperature pattern and also showed the effects of density differences and wind action on the steam-electric station (S.E.S.) effluent plume. Mean annual salinity for a 5-year period (1963–1967) was highest in 1966, about 12.3 ‰, and lowest in 1967, about 9.9‰. Dissolved oxygen values for 1966–1967 ranged from 3.2 to 15.6 mg/l, and saturation ranged from 55 to 152%. Turbidity levels were inversely related to salinity, with the highest annual, mean of 28 JCU (Jackson Candle Units) occurring in 1967, the lowest salinity year. The extreme tide range was 2.1 m (6.7 ft); mean water levels at the Patuxent Bridge were highest in summer and lowest in winter. Water stages are more affected by wind speed and direction than by flow in the river.

Seasonal abundance of eggplant leafminer Liriomyza sativae (Blanchard, 1938) (Diptera, Agromyzidae) in plastic-house

NASA Astrophysics Data System (ADS)

Kathiar, S. A.; Flaih, S. K.; Al-Khazraji, H. I.; Ismael, S. K.

2018-05-01

The eggplant Solanum melongena L. crop is attacked by one of the most common pests which is the leafminer Liriomyza sativae (Blanchard, 1938); therefore, this investigation was conducted to study the seasonal abundance of the eggplant leafminer in eggplant Plastic-house. The results showed that the highest average of infested leaves was 6.67 leaf, the highest average of tunnels by leaf miner was 9.87 tunnels and the highest percent of infestation was recorded 30.5% in 23. April. 2017. This study showed the parasitoid Diglyphus isaea (Walker, 1838) (Hymenoptera, Eulophidae) was recorded as a natural enemy to control the pest and the highest incidence of parasitism was 32.2 parasites on average in 16. April. 2017.

76 FR 79579 - Approval and Promulgation of Implementation Plans and Designation of Areas for Air Quality...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-22

... posting of the availability of the submittal on EPA's Adequacy Web site (at http://www.epa.gov/otaq... average annual fourth-highest daily maximum 8-hour average ozone concentration), if it had a 1-hour design... ozone standard is attained when the three-year average of the annual fourth-highest daily maximum 8-hour...

RESIDENTIAL EXPOSURE TO EXTREMELY LOW FREQUENCY ELECTRIC AND MAGNETIC FIELDS IN THE CITY OF RAMALLAH-PALESTINE.

PubMed

Abuasbi, Falastine; Lahham, Adnan; Abdel-Raziq, Issam Rashid

2018-04-01

This study was focused on the measurement of residential exposure to power frequency (50-Hz) electric and magnetic fields in the city of Ramallah-Palestine. A group of 32 semi-randomly selected residences distributed amongst the city were under investigations of fields variations. Measurements were performed with the Spectrum Analyzer NF-5035 and were carried out at one meter above ground level in the residence's bedroom or living room under both zero and normal-power conditions. Fields' variations were recorded over 6-min and some times over few hours. Electric fields under normal-power use were relatively low; ~59% of residences experienced mean electric fields <10 V/m. The highest mean electric field of 66.9 V/m was found at residence R27. However, electric field values were log-normally distributed with geometric mean and geometric standard deviation of 9.6 and 3.5 V/m, respectively. Background electric fields measured under zero-power use, were very low; ~80% of residences experienced background electric fields <1 V/m. Under normal-power use, the highest mean magnetic field (0.45 μT) was found at residence R26 where an indoor power substation exists. However, ~81% of residences experienced mean magnetic fields <0.1 μT. Magnetic fields measured inside the 32 residences showed also a log-normal distribution with geometric mean and geometric standard deviation of 0.04 and 3.14 μT, respectively. Under zero-power conditions, ~7% of residences experienced average background magnetic field >0.1 μT. Fields from appliances showed a maximum mean electric field of 67.4 V/m from hair dryer, and maximum mean magnetic field of 13.7 μT from microwave oven. However, no single result surpassed the ICNIRP limits for general public exposures to ELF fields, but still, the interval 0.3-0.4 μT for possible non-thermal health impacts of exposure to ELF magnetic fields, was experienced in 13% of the residences.

A MEMS turbine prototype for respiration harvesting

NASA Astrophysics Data System (ADS)

Goreke, U.; Habibiabad, S.; Azgin, K.; Beyaz, M. I.

2015-12-01

The design, manufacturing, and performance characterization of a MEMS-scale turbine prototype is reported. The turbine is designed for integration into a respiration harvester that can convert normal human breathing into electrical power through electromagnetic induction. The device measures 10 mm in radius, and employs 12 blades located around the turbine periphery along with ball bearings around the center. Finite element simulations showed that an average torque of 3.07 μNm is induced at 12 lpm airflow rate, which lies in normal breathing levels. The turbine and a test package were manufactured using CNC milling on PMMA. Tests were performed at respiration flow rates between 5-25 lpm. The highest rotational speed was measured to be 9.84 krpm at 25 lpm, resulting in 8.96 mbar pressure drop across the device and 370 mW actuation power.

Excess Capacity in China’s Power Systems: A Regional Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, Jiang; Liu, Xu; Karl, Fredrich

2016-11-01

This paper examines China’s regional electricity grids using a reliability perspective, which is commonly measured in terms of a reserve margin. Our analysis shows that at the end of 2014, the average reserve margin for China as a whole was roughly 28%, almost twice as high as a typical planning reserve margin in the U.S. However, this national average masks huge variations in reserve margins across major regional power grid areas: the northeastern region has the highest reserve margin of over 60%, followed by the northwestern region at 49%, and the southern grid area at 35%. In this analysis, wemore » also examined future reserve margins for regional electricity grids in China under two scenarios: 1) a low scenario of national annual electricity consumption growth rates of 1.5% between 2015 and 2020 and 1.0% between 2020 and 2025, and 2) a high scenario of annual average growth rates of 3.0% and 2.0%, respectively. Both scenarios suggest that the northeastern, northwestern, and southern regions have significant excess generation capacity, and that this excess capacity situation will continue over the next decade without regulatory intervention. The northern and central regions could have sufficient generation capacity to 2020, but may require additional resources in a higher growth scenario. The eastern region requires new resources by 2020 in both scenarios.« less

Physiology response of fourth generation saline resistant soybean (Glycine max (L.) Merrill) with application of several types of antioxidants

NASA Astrophysics Data System (ADS)

Manurung, I. R.; Rosmayati; Rahmawati, N.

2018-02-01

Antioxidant applications are expected to reduce the adverse effects of soil saline. This research was conducted in plastic house, Plant Tissue Laboratory Faculty of Agriculture and Plant Physiology Laboratory Faculty of Mathematic and Natural Science, Universitas Sumatera Utara, Medan also in Research Centers and Industry Standardization, Medan from July-December 2016. The objective of the research was to know the effect of various antioxidant treatments with different concentrations (control, ascorbic acid 250, 500 and 750 ppm; salicylic acid 250, 500 and 750 ppm; α-tocopherol 250, 500 and 750 ppm) on fourth generation soybean physiology in saline condition (Electric Conductivity 5-6 dS/m). The results of this research showed that the antioxidant type and concentration affected not significantly to physiology of fourth generation soybean. Descriptively the highest average of superoxide dismutase and peroxide dismutase was showed on ascorbic acid 250 ppm. The highest average of ascorbate peroxidase was showed on α-tocopherol 750 ppm. The highest average of carotenoid content was showed on ascorbic acid 500 ppm. The highest average of chlorophyll content was showed on α-tocopherol 250 ppm. The highest average of ratio of K/Na was showed on salicylic acid 250 ppm.

The Japanese Positron Factory

NASA Astrophysics Data System (ADS)

Okada, S.; Sunaga, H.; Kaneko, H.; Takizawa, H.; Kawasuso, A.; Yotsumoto, K.; Tanaka, R.

1999-06-01

The Positron Factory has been planned at Japan Atomic Energy Research Institute (JAERI). The factory is expected to produce linac-based monoenergetic positron beams having world-highest intensities of more than 1010e+/sec, which will be applied for R&D of materials science, biotechnology and basic physics & chemistry. In this article, results of the design studies are demonstrated for the following essential components of the facilities: 1) Conceptual design of a high-power electron linac with 100 MeV in beam energy and 100 kW in averaged beam power, 2) Performance tests of the RF window in the high-power klystron and of the electron beam window, 3) Development of a self-driven rotating electron-to-positron converter and the performance tests, 4) Proposal of multi-channel beam generation system for monoenergetic positrons, with a series of moderator assemblies based on a newly developed Monte Carlo simulation and the demonstrative experiment, 5) Proposal of highly efficient moderator structures, 6) Conceptual design of a local shield to suppress the surrounding radiation and activation levels.

Turbulent heat transfer and nanofluid flow in a protruded ribbed square passage

NASA Astrophysics Data System (ADS)

Kumar, Sunil; Kothiyal, Alok Darshan; Bisht, Mangal Singh; Kumar, Anil

In this article, turbulent heat transfer of nanofluid flow in square passage with protruded rib shape is numerically and experimentally studied over Reynolds number ranges of 4000-18000. Different nanoparticles (Al2O3, CuO, and ZnO), with different concentration (φ) range of 1-4% and different nanoparticle diameter (dnp) range of 30-45 nm are disperse in water (base fluid). Several parameters such as stream wise distance (Xs /dp) range of 1.4-2.6, span wise distance (Ys /dp) range of 1.4-2.6, ratio of protruded height to print diameter (ep /dp) range of 0.83-1.67 also studied to find the consequence on thermal and hydrodynamic characteristics. Simulations were carried out to obtain heat and fluid flow behaviour of smooth and ribbed square channel using commercial CFD software, ANSYS 15.0 (Fluent). Renormalization k - ε model was employed to assess the influence of protruded ribs on turbulent flow and velocity field. The outcome indicates that Al2O3 nanofluid has the highest value of average Nusselt number as compare to other nanofluids. The average Nusselt number increases as the concentration increases and it decreases as nanoparticle diameter increases. The thermal hydrodynamic performance parameter based on equal pumping power, average Nusselt number and average friction factor were found to be highest for Al2O3, φ = 0.04, dnp = 30 nm, Xs /dp = 1.8, Ys /dp = 1.8 and ep /dp = 1.0 . The numerical data are compared with the corresponding experimental data. Comparison between CFD and experimental analysis results showed that good agreement as the data fell within ±7.0% error band.

75 FR 43069 - Approval of One-Year Extension for Attaining the 1997 8-Hour Ozone Standard in the Baltimore...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-23

... standard (NAAQS). This extension is based in part on air quality data for the 4th highest daily 8-hour... attainment date if: (a) For the first one-year extension, the area's 4th highest daily 8-hour average in the... 4th highest daily 8-hour value, averaged over both the original attainment year and the first...

Defining and measuring cyberbullying within the larger context of bullying victimization.

PubMed

Ybarra, Michele L; Boyd, Danah; Korchmaros, Josephine D; Oppenheim, Jay Koby

2012-07-01

To inform the scientific debate about bullying, including cyberbullying, measurement. Two split-form surveys were conducted online among 6-17-year-olds (n = 1,200 each) to inform recommendations for cyberbullying measurement. Measures that use the word "bully" result in prevalence rates similar to each other, irrespective of whether a definition is included, whereas measures not using the word "bully" are similar to each other, irrespective of whether a definition is included. A behavioral list of bullying experiences without either a definition or the word "bully" results in higher prevalence rates and likely measures experiences that are beyond the definition of "bullying." Follow-up questions querying differential power, repetition, and bullying over time were used to examine misclassification. The measure using a definition but not the word "bully" appeared to have the highest rate of false positives and, therefore, the highest rate of misclassification. Across two studies, an average of 25% reported being bullied at least monthly in person compared with an average of 10% bullied online, 7% via telephone (cell or landline), and 8% via text messaging. Measures of bullying among English-speaking individuals in the United States should include the word "bully" when possible. The definition may be a useful tool for researchers, but results suggest that it does not necessarily yield a more rigorous measure of bullying victimization. Directly measuring aspects of bullying (i.e., differential power, repetition, over time) reduces misclassification. To prevent double counting across domains, we suggest the following distinctions: mode (e.g., online, in-person), type (e.g., verbal, relational), and environment (e.g., school, home). We conceptualize cyberbullying as bullying communicated through the online mode. Copyright © 2012 Society for Adolescent Health and Medicine. Published by Elsevier Inc. All rights reserved.

Measurements of ultrafine particles and other vehicular pollutants inside school buses in South Texas

NASA Astrophysics Data System (ADS)

Zhang, Qunfang; Zhu, Yifang

2010-01-01

Increasing evidence has demonstrated toxic effects of vehicular emitted ultrafine particles (UFPs, diameter < 100 nm), with the highest human exposure usually occurring on and near roadways. Children are particularly at risk due to immature respiratory systems and faster breathing rates. In this study, children's exposure to in-cabin air pollutants, especially UFPs, was measured inside four diesel-powered school buses. Two 1990 and two 2006 model year diesel-powered school buses were selected to represent the age extremes of school buses in service. Each bus was driven on two routine bus runs to study school children's exposure under different transportation conditions in South Texas. The number concentration and size distribution of UFPs, total particle number concentration, PM 2.5, PM 10, black carbon (BC), CO, and CO 2 levels were monitored inside the buses. The average total particle number concentrations observed inside the school buses ranged from 7.3 × 10 3 to 3.4 × 10 4 particles cm -3, depending on engine age and window position. When the windows were closed, the in-cabin air pollutants were more likely due to the school buses' self-pollution. The 1990 model year school buses demonstrated much higher air pollutant concentrations than the 2006 model year ones. When the windows were open, the majority of in-cabin air pollutants came from the outside roadway environment with similar pollutant levels observed regardless of engine ages. The highest average UFP concentration was observed at a bus transfer station where approximately 27 idling school buses were queued to load or unload students. Starting-up and idling generated higher air pollutant levels than the driving state. Higher in-cabin air pollutant concentrations were observed when more students were on board.

Spatial distribution of topsoil magnetic susceptibility in Sawahlunto City, West Sumatera

NASA Astrophysics Data System (ADS)

Afdal; Wahyuni, E. S.

2018-03-01

A research to determine the spatial distribution of top soil magnetic suceptibility at Sawahlunto City, West Sumatra has been conducted. The top soil samples were taken at four locations ie the downtown area, the steam power plant area, the agricultural area, and coal mine area. At each location, the soil samples were taken at 10 points at a depth of 20 cm. Magnetic susceptibility were measured using Bartington MS2B Magnetic Susceptibility Meter. The topsoil samples from Sawahlunto city have relatively low average value of the magnetic susceptibility that is 67.0×10-8 m3/kg. The magnetic susceptibility of topsoil samples from downtown area have the average and the highest value of magnetic susceptibility (100.6×10-8 and 259.9×10-8 m3/kg), and followed by sample from the steam power plant area (98.4×10-8 and 258.0×10-8 m3/kg), the agricultural area (56.2×10-8 and 83.7×10-8 m3/kg), and coal mine area (12.9×10-8 and 26.8×10-8 m3/kg). Soil samples from the steam power plant area have the widest range of magnetic susceptibility value range from 0.3 × 10-8 to 258.0 × 10-8 m3/kg.

[Water-soluble anions of atmosphere on Tianwan nuclear power station].

PubMed

Zhao, Heng-Qiang; He, Ying; Zheng, Xiao-Ling; Chen, Fa-Rong; Pang, Shi-Ping; Wang, Cai-Xia; Wang, Xiao-Ru

2010-11-01

Three major water-soluble anions (Cl-, SO4(2-) and NO3-) in the atmosphere of the Tianwan nuclear power station in Lianyungang were determined by ion chromatography from June 2005 to May 2006. The results showed that the annual average concentration of Cl-, SO4(2-) and NO3- in the atmosphere of Tianwan nuclear power station was (33.12 +/- 53.63) microg x m(-3), (53.34 +/- 30.34) microg x m(-3) and (8.34 +/- 4.47) microg x m(-3), respectively. The concentrations of the three water-soluble anions showed evident trend of seasonal variation. The concentrations of Cl-, SO4(2-) reached the highest level in summer and the lowest level in winter, while the concentration of NO3- in autumn and winter was higher than those in summer and spring. Meteorological parameters such as wind direction, wind speed, temperature and relative humidity were studied and showed definite influence to the anions concentration of the atmosphere. This is the first simultaneous monitoring of corrosive anions in the atmosphere of Chinese coastal nuclear power plant, and it will provide basis for the prevention of marine atmospheric corrosion, which will ensure the safely operating of our nuclear power industry.

Dissolved Copper, Nickel and Lead in Tampamachoco Lagoon and Tuxpan River Estuary in the SW Gulf of Mexico.

PubMed

Garduño Ruiz, E P; Rosales Hoz, L; Carranza Edwards, A

2016-10-01

In order to estimate the effects of a thermal power plant, physicochemical parameters and the concentrations of copper, nickel and lead were evaluated in water from both Tampamachoco Lagoon and the estuary of the Tuxpan River. Average salinities were 33.66 ups in the lagoon area, 32.77 ups in the channel that joins the lagoon and the river, and 24.74 ups in the river estuary. Total average metal concentrations were 21.95 for Cu, 29.67 for Ni and 4.31 µ/L for Pb. Sampling point 1 and samples from the bottom water of the lagoon present the highest salinities and concentrations of suspended matter, TOC, Cu, Ni and Pb.These high values may be associated with the infiltration of sea water either from plant operation or from the channel that connects the lagoon with the sea.

40 CFR 51.907 - For an area that fails to attain the 8-hour NAAQS by its attainment date, how does EPA interpret...

Code of Federal Regulations, 2011 CFR

2011-07-01

... to 1-year extensions of the attainment date if: (a) For the first 1-year extension, the area's 4th... extension, the area's 4th highest daily 8-hour value, averaged over both the original attainment year and... section, the area's 4th highest daily 8-hour average shall be from the monitor with the highest 4th...

40 CFR 51.907 - For an area that fails to attain the 8-hour NAAQS by its attainment date, how does EPA interpret...

Code of Federal Regulations, 2013 CFR

2013-07-01

... to 1-year extensions of the attainment date if: (a) For the first 1-year extension, the area's 4th... extension, the area's 4th highest daily 8-hour value, averaged over both the original attainment year and... section, the area's 4th highest daily 8-hour average shall be from the monitor with the highest 4th...

40 CFR 51.907 - For an area that fails to attain the 8-hour NAAQS by its attainment date, how does EPA interpret...

Code of Federal Regulations, 2012 CFR

2012-07-01

... to 1-year extensions of the attainment date if: (a) For the first 1-year extension, the area's 4th... extension, the area's 4th highest daily 8-hour value, averaged over both the original attainment year and... section, the area's 4th highest daily 8-hour average shall be from the monitor with the highest 4th...

[Simulation study of air quality health index in 5 cities in China: 2013-2015].

PubMed

Wang, W T; Sun, Q H; Qin, J; Li, T T; Shi, X M

2017-03-10

Objective: To construct the air quality health index (AQHI) by inclusion of air pollutants PM(2.5) and O(3) in Guangzhou, Shanghai, Xi' an, Beijing, Shenyang, and explore scientificity and feasibility of its application in China. Methods: The daily average concentrations of PM(2.5) and O(3) in air, and daily average mortality from 2013 to 2015 in the 5 cities in China, the exposure-response coefficients of PM(2.5) and O(3) and total mortality from Meta studies in China were used to construct local AQHI. The health risk levels of air pollution in the 5 cities were calculated and compared with the characteristics of single pollutant concentrationof PM(2.5) or O(3). Results: In the 5 cities, the average concentration of PM(2.5) was highest in Beijing (82 μg/m(3)) and lowest in Guangzhou (46 μg/m(3)). And the average concentration of O(3) was highest in Shanghai (72 μg/m(3)) and lowest in Xi' an (45 μg/m(3)). In all the cities, the average concentration of PM(2.5) was highest in winter and lowest in summer. In summer, the average concentration of O(3) was lowest. But the health risk level of AQHI showed that the 5 cities had higher frequency of low or medium risk averagely. And Beijing had the highest frequency of high risk in summer (5.69%). Xi' an had the highest frequency of extremely high risk in winter (1.63%). Conclusions: In this study, AQHI could be constructed by using air PM(2.5) and O(3) concentration data which can be obtained in many areas in China. The application of this index is scientific and feasible in China.

Integrated modelling of H-mode pedestal and confinement in JET-ILW

NASA Astrophysics Data System (ADS)

Saarelma, S.; Challis, C. D.; Garzotti, L.; Frassinetti, L.; Maggi, C. F.; Romanelli, M.; Stokes, C.; Contributors, JET

2018-01-01

A pedestal prediction model Europed is built on the existing EPED1 model by coupling it with core transport simulation using a Bohm-gyroBohm transport model to self-consistently predict JET-ILW power scan for hybrid plasmas that display weaker power degradation than the IPB98(y, 2) scaling of the energy confinement time. The weak power degradation is reproduced in the coupled core-pedestal simulation. The coupled core-pedestal model is further tested for a 3.0 MA plasma with the highest stored energy achieved in JET-ILW so far, giving a prediction of the stored plasma energy within the error margins of the measured experimental value. A pedestal density prediction model based on the neutral penetration is tested on a JET-ILW database giving a prediction with an average error of 17% from the experimental data when a parameter taking into account the fuelling rate is added into the model. However the model fails to reproduce the power dependence of the pedestal density implying missing transport physics in the model. The future JET-ILW deuterium campaign with increased heating power is predicted to reach plasma energy of 11 MJ, which would correspond to 11-13 MW of fusion power in equivalent deuterium-tritium plasma but with isotope effects on pedestal stability and core transport ignored.

Analysis of mobile phone design features affecting radiofrequency power absorbed in a human head phantom.

PubMed

Kuehn, Sven; Kelsh, Michael A; Kuster, Niels; Sheppard, Asher R; Shum, Mona

2013-09-01

The US FCC mandates the testing of all mobile phones to demonstrate compliance with the rule requiring that the peak spatial SAR does not exceed the limit of 1.6 W/kg averaged over any 1 g of tissue. These test data, measured in phantoms with mobile phones operating at maximum antenna input power, permitted us to evaluate the variation in SARs across mobile phone design factors such as shape and antenna design, communication technology, and test date (over a 7-year period). Descriptive statistical summaries calculated for 850 MHz and 1900 MHz phones and ANOVA were used to evaluate the influence of the foregoing factors on SARs. Service technology accounted for the greatest variability in compliance test SARs that ranged from AMPS (highest) to CDMA, iDEN, TDMA, and GSM (lowest). However, the dominant factor for SARs during use is the time-averaged antenna input power, which may be much less than the maximum power used in testing. This factor is largely defined by the communication system; e.g., the GSM phone average output can be higher than CDMA by a factor of 100. Phone shape, antenna type, and orientation of a phone were found to be significant but only on the order of up to a factor of 2 (3 dB). The SAR in the tilt position was significantly smaller than for touch. The side of the head did not affect SAR levels significantly. Among the remaining factors, external antennae produced greater SARs than internal ones, and brick and clamshell phones produced greater SARs than slide phones. Assuming phone design and usage patterns do not change significantly over time, we have developed a normalization procedure and formula that permits reliable prediction of the relative SAR between various communication systems. This approach can be applied to improve exposure assessment in epidemiological research. Copyright © 2013 Wiley Periodicals, Inc.

The influence of wheelchair propulsion technique on upper extremity muscle demand: a simulation study.

PubMed

Rankin, Jeffery W; Kwarciak, Andrew M; Richter, W Mark; Neptune, Richard R

2012-11-01

The majority of manual wheelchair users will experience upper extremity injuries or pain, in part due to the high force requirements, repetitive motion and extreme joint postures associated with wheelchair propulsion. Recent studies have identified cadence, contact angle and peak force as important factors for reducing upper extremity demand during propulsion. However, studies often make comparisons between populations (e.g., able-bodied vs. paraplegic) or do not investigate specific measures of upper extremity demand. The purpose of this study was to use a musculoskeletal model and forward dynamics simulations of wheelchair propulsion to investigate how altering cadence, peak force and contact angle influence individual muscle demand. Forward dynamics simulations of wheelchair propulsion were generated to emulate group-averaged experimental data during four conditions: 1) self-selected propulsion technique, and while 2) minimizing cadence, 3) maximizing contact angle, and 4) minimizing peak force using biofeedback. Simulations were used to determine individual muscle mechanical power and stress as measures of muscle demand. Minimizing peak force and cadence had the lowest muscle power requirements. However, minimizing peak force increased cadence and recovery power, while minimizing cadence increased average muscle stress. Maximizing contact angle increased muscle stress and had the highest muscle power requirements. Minimizing cadence appears to have the most potential for reducing muscle demand and fatigue, which could decrease upper extremity injuries and pain. However, altering any of these variables to extreme values appears to be less effective; instead small to moderate changes may better reduce overall muscle demand. Copyright © 2012 Elsevier Ltd. All rights reserved.

2016 Wind Technologies Market Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wiser, Ryan H.; Bolinger, Mark

The U.S. Department of Energy (DOE)’s Wind Technologies Market Report provides an annual overview of trends in the U.S. wind power market. You can find the report, a presentation, and a data file on the Files tab, below. Additionally, several data visualizations are available in the Data Visualizations tab. Highlights of this year’s report include: -Wind power additions continued at a rapid clip in 2016: $13 billion was invested in new wind power plants in 2016. In 2016, wind energy contributed 5.6% of the nation’s electricity supply, more than 10% of total electricity generation in fourteen states, and 29% tomore » 37% in three of those states—Iowa, South Dakota, and Kansas. -Bigger turbines are enhancing wind project performance: Increased blade lengths, in particular, have dramatically increased wind project capacity factors, one measure of project performance. For example, the average 2016 capacity factor among projects built in 2014 and 2015 was 42.6%, compared to an average of 32.1% among projects built from 2004 to 2011 and 25.4% among projects built from 1998 to 2001. -Low wind turbine pricing continues to push down installed project costs: Wind turbine prices have fallen from their highs in 2008, to $800–$1,100/kW. Overall, the average installed cost of wind projects in 2016 was $1,590/kW, down $780/kW from the peak in 2009 and 2010. -Wind energy prices remain low: After topping out at nearly 7¢/kWh for power purchase agreements (PPAs) executed in 2009, the national average price of wind PPAs has dropped to around 2¢/kWh—though this nationwide average is dominated by projects that hail from the lowest-priced Interior region of the country (such as Texas, Iowa, Oklahoma). These prices, which are possible in part due to federal tax support, compare favorably to the projected future fuel costs of gas-fired generation. -The supply chain continued to adjust to swings in domestic demand for wind equipment: Wind sector employment reached a new high of more than 101,000 full-time workers at the end of 2016. For wind projects recently installed in the U.S., domestically manufactured content is highest for nacelle assembly (>90%), towers (65-80%), and blades and hubs (50-70%), but is much lower (<20%) for most components internal to the turbine. -Continued strong growth in wind capacity is anticipated in the near term: With federal tax incentives still available, though declining, various forecasts for the domestic market show expected wind power capacity additions averaging more than 9,000 MW/year from 2017 to 2020.« less

Robustness of Controllability for Networks Based on Edge-Attack

PubMed Central

Nie, Sen; Wang, Xuwen; Zhang, Haifeng; Li, Qilang; Wang, Binghong

2014-01-01

We study the controllability of networks in the process of cascading failures under two different attacking strategies, random and intentional attack, respectively. For the highest-load edge attack, it is found that the controllability of Erdős-Rényi network, that with moderate average degree, is less robust, whereas the Scale-free network with moderate power-law exponent shows strong robustness of controllability under the same attack strategy. The vulnerability of controllability under random and intentional attacks behave differently with the increasing of removal fraction, especially, we find that the robustness of control has important role in cascades for large removal fraction. The simulation results show that for Scale-free networks with various power-law exponents, the network has larger scale of cascades do not mean that there will be more increments of driver nodes. Meanwhile, the number of driver nodes in cascading failures is also related to the edges amount in strongly connected components. PMID:24586507

Robustness of controllability for networks based on edge-attack.

PubMed

Nie, Sen; Wang, Xuwen; Zhang, Haifeng; Li, Qilang; Wang, Binghong

2014-01-01

We study the controllability of networks in the process of cascading failures under two different attacking strategies, random and intentional attack, respectively. For the highest-load edge attack, it is found that the controllability of Erdős-Rényi network, that with moderate average degree, is less robust, whereas the Scale-free network with moderate power-law exponent shows strong robustness of controllability under the same attack strategy. The vulnerability of controllability under random and intentional attacks behave differently with the increasing of removal fraction, especially, we find that the robustness of control has important role in cascades for large removal fraction. The simulation results show that for Scale-free networks with various power-law exponents, the network has larger scale of cascades do not mean that there will be more increments of driver nodes. Meanwhile, the number of driver nodes in cascading failures is also related to the edges amount in strongly connected components.

Losses in chopper-controlled DC series motors

NASA Technical Reports Server (NTRS)

Hamilton, H. B.

1982-01-01

Motors for electric vehicle (EV) applications must have different features than dc motors designed for industrial applications. The EV motor application is characterized by the following requirements: (1) the need for highest possible efficiency from light load to overload, for maximum EV range, (2) large short time overload capability (The ratio of peak to average power varies from 5/1 in heavy city traffic to 3/1 in suburban driving situations) and (3) operation from power supply voltage levels of 84 to 144 volts (probably 120 volts maximum). A test facility utilizing a dc generator as a substitute for a battery pack was designed and utilized. Criteria for the design of such a facility are presented. Two motors, differing in design detail, commercially available for EV use were tested. Losses measured are discussed, as are waves forms and their harmonic content, the measurements of resistance and inductance, EV motor/chopper application criteria, and motor design considerations.

NASA electrothermal auxiliary propulsion technology

NASA Technical Reports Server (NTRS)

Stone, J. R.

1986-01-01

Electrothermal auxiliary propulsion systems provide high performance options which can have major mission benefits. There are several electrothermal concepts which offer a range of characteristics and benefits. Resistojets are the highest thrust to power option and are currently operational at mission average values of specific impulse, I sub sp approximately 295 sec. Long life, multipropellant resistojets are being developed for the space station, and resistojet technology advancements are being pursued to improve the I sub sp by more than 20 percent for resistojets used in satellite applications. Direct current arcjets have the potential of I sub sp over 400 sec with storable propellants and should provide over 1000 sec with hydrogen. Advanced concepts are being investigated to provide high power density options and possible growth to primary propulsion applications. Broad based experimental and analytical research and technology programs of NASA are summarized and recent significant advances are reviewed.

High β produced by neutral beam injection in the START (Small Tight Aspect Ratio Tokamak) spherical tokamak

NASA Astrophysics Data System (ADS)

Sykes, Alan

1997-05-01

The world's first high-power auxiliary heating experiments in a tight aspect ratio (or spherical) tokamak have been performed on the Small Tight Aspect Ratio Tokomak (START) device [Sykes et al., Nucl. Fusion 32, 694 (1992)] at Culham Laboratory, using the 40 keV, 0.5 MW Neutral Beam Injector loaned by the Oak Ridge National Laboratory. Injection has been mainly of hydrogen into hydrogen or deuterium target plasmas, with a one-day campaign to explore D→D operation. In each case injection provides a combination of higher density operation and effective heating of both ions and electrons. The highest β values achieved to date in START are volume average βT˜11.5% and central beta βO˜50%. Already high, these values are expected to increase further with the use of higher beam power.

Distribution of the Crystalline Lens Power In Vivo as a Function of Age.

PubMed

Jongenelen, Sien; Rozema, Jos J; Tassignon, Marie-José

2015-11-01

To observe the age-related changes in crystalline lens power in vivo in a noncataractous European population. Data were obtained though Project Gullstrand, a multicenter population study with data from healthy phakic subjects between 20 and 85 years old. One randomly selected eye per subject was used. Lens power was calculated using the modified Bennett-Rabbetts method, using biometry data from an autorefractometer, Oculus Pentacam, and Haag-Streit Lenstar. The study included 1069 Caucasian subjects (490 men, 579 women) with a mean age of 44.2 ± 14.2 years and mean lens power of 24.96 ± 2.18 diopters (D). The average lens power showed a statistically significant decrease as a function of age, with a steeper rate of decrease after the age of 55. The highest crystalline lens power was found in emmetropic eyes and eyes with a short axial length. The correlation of lens power with different refractive components was statistically significant for axial length (r = -0.523, P < 0.01) and anterior chamber depth (r = -0.161, P < 0.01), but not for spherical equivalent and corneal power (P > 0.05). This in vivo study showed a monotonous decrease in crystalline lens power with age, with a steeper decline after 55 years. While this finding fundamentally concurs with previous in vivo studies, it is at odds with studies performed on donor eyes that reported lens power increases after the age of 55.

40 CFR 63.2263 - Initial compliance demonstration for a dry rotary dryer.

Code of Federal Regulations, 2010 CFR

2010-07-01

... operate a dry rotary dryer, you must demonstrate that your dryer processes furnish with an inlet moisture.... You must record the inlet furnish moisture content (dry basis) and inlet dryer operating temperature... highest recorded 24-hour average inlet furnish moisture content and the highest recorded 24-hour average...

40 CFR 63.2263 - Initial compliance demonstration for a dry rotary dryer.

Code of Federal Regulations, 2011 CFR

2011-07-01

... operate a dry rotary dryer, you must demonstrate that your dryer processes furnish with an inlet moisture.... You must record the inlet furnish moisture content (dry basis) and inlet dryer operating temperature... highest recorded 24-hour average inlet furnish moisture content and the highest recorded 24-hour average...

Determination of concentration factors for Cs-137 and Ra-226 in the mullet species Chelon labrosus (Mugilidae) from the South Adriatic Sea.

PubMed

Antovic, Ivanka; Antovic, Nevenka M

2011-07-01

Concentration factors for Cs-137 and Ra-226 transfer from seawater, and dried sediment or mud with detritus, have been determined for whole, fresh weight, Chelon labrosus individuals and selected organs. Cesium was detected in 5 of 22 fish individuals, and its activity ranged from 1.0 to 1.6 Bq kg(-1). Radium was detected in all fish, and ranged from 0.4 to 2.1 Bq kg(-1), with an arithmetic mean of 1.0 Bq kg(-1). In regards to fish organs, cesium activity concentration was highest in muscles (maximum - 3.7 Bq kg(-1)), while radium was highest in skeletons (maximum - 25 Bq kg(-1)). Among cesium concentration factors, those for muscles were the highest (from seawater - an average of 47, from sediment - an average of 3.3, from mud with detritus - an average of 0.8). Radium concentration factors were the highest for skeleton (from seawater - an average of 130, from sediment - an average of 1.8, from mud with detritus - an average of 1.5). Additionally, annual intake of cesium and radium by human adults consuming muscles of this fish species has been estimated to provide, in aggregate, an effective dose of about 4.1 μSv y(-1). 2011 Elsevier Ltd. All rights reserved.

Pulsed counter-current ultrasound-assisted extraction and characterization of polysaccharides from Boletus edulis.

PubMed

You, Qinghong; Yin, Xiulian; Ji, Chaowen

2014-01-30

Four methods for extracting polysaccharides from Boletus edulis, namely, hot-water extraction, ultrasonic clearer extraction, static probe ultrasonic extraction, and pulsed counter-current probe ultrasonic extraction (CCPUE), were studied. Results showed that CCPUE has the highest extraction efficiency among the methods studied. Under optimal CCPUE conditions, a B. edulis polysaccharide (BEP) yield of 8.21% was obtained. Three purified fractions, BEP-I, BEP-II, and BEP-III, were obtained through sequential purification by DEAE-52 and Sephadex G-75 chromatography. The average molecular weights of BEP-I, BEP-II, and BEP-III were 10,278, 23,761, and 42,736 Da, respectively. The polysaccharides were mainly composed of xylose, mannose, galactose, and glucose; of these, mannose contents were the highest. The antioxidant activities of the BEPs were further investigated by measurement of their ability to scavenge DPPH and hydroxyl radicals as well as their reducing power. The results indicated that the BEPs have good antioxidant activity. Copyright © 2013 Elsevier Ltd. All rights reserved.

Benthic microbial fuel cell as direct power source for an acoustic modem and seawater oxygen/temperature sensor system.

PubMed

Gong, Yanming; Radachowsky, Sage E; Wolf, Michael; Nielsen, Mark E; Girguis, Peter R; Reimers, Clare E

2011-06-01

Supported by the natural potential difference between anoxic sediment and oxic seawater, benthic microbial fuel cells (BMFCs) promise to be ideal power sources for certain low-power marine sensors and communication devices. In this study a chambered BMFC with a 0.25 m(2) footprint was used to power an acoustic modem interfaced with an oceanographic sensor that measures dissolved oxygen and temperature. The experiment was conducted in Yaquina Bay, Oregon over 50 days. Several improvements were made in the BMFC design and power management system based on lessons learned from earlier prototypes. The energy was harvested by a dynamic gain charge pump circuit that maintains a desired point on the BMFC's power curve and stores the energy in a 200 F supercapacitor. The system also used an ultralow power microcontroller and quartz clock to read the oxygen/temperature sensor hourly, store data with a time stamp, and perform daily polarizations. Data records were transmitted to the surface by the acoustic modem every 1-5 days after receiving an acoustic prompt from a surface hydrophone. After jump-starting energy production with supplemental macroalgae placed in the BMFC's anode chamber, the average power density of the BMFC adjusted to 44 mW/m(2) of seafloor area which is better than past demonstrations at this site. The highest power density was 158 mW/m(2), and the useful energy produced and stored was ≥ 1.7 times the energy required to operate the system.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lentine, Anthony L.; Cox, Jonathan Albert

Methods and systems for stabilizing a resonant modulator include receiving pre-modulation and post-modulation portions of a carrier signal, determining the average power from these portions, comparing an average input power to the average output power, and operating a heater coupled to the modulator based on the comparison. One system includes a pair of input structures, one or more processing elements, a comparator, and a control element. The input structures are configured to extract pre-modulation and post-modulation portions of a carrier signal. The processing elements are configured to determine average powers from the extracted portions. The comparator is configured to comparemore » the average input power and the average output power. The control element operates a heater coupled to the modulator based on the comparison.« less

Co-digestion of domestic kitchen waste and night soil sludge in a full-scale sludge treatment plant.

PubMed

Yoneyama, Y; Takeno, K

2002-01-01

A study was made on the domestic kitchen waste and night soil treatment performance of a full-scale sludge treatment plant. The sludge treatment at this plant was by thermophilic methane fermentation. The initial treatment, mesophilic to thermophilic fermentation, was able to be started up within a short time by adjusting the amount of influent waste. Thermophilic methane fermentation was carried out for five months (May-October) and the performance under a mean residual time of 22 days indicated a VTS decomposition of 42%, gas generation of 54-1,610 m3/day (average: 755 m3/day), and a mean methane concentration of 60%. The methane gas was used to generate power in the plant and the amount of power generated by methane gas was highest in October (average of 1,200 kWh/day). This was equivalent to about 7% of the power consumed at the entire sludge treatment plant. The BOD/NH4-N of the activated sludge influent water was lower, compared to a case where there is no recycle flow, due to the recycle flow from the methane fermentation process. There was, therefore, a tendency for an increase in the amount of methanol charged into the secondary denitrification tank. However, the quality of the effluent was satisfactory (BOD< 10 mg/L, SS< 5 mg/L, and T-N< 25 mg/L). Study results indicated that it was possible to implement a full-scale plant for recovering organic waste.

Evaluation of the quality of the college library websites in Iranian medical Universities based on the Stover model.

PubMed

Nasajpour, Mohammad Reza; Ashrafi-Rizi, Hasan; Soleymani, Mohammad Reza; Shahrzadi, Leila; Hassanzadeh, Akbar

2014-01-01

Today, the websites of college and university libraries play an important role in providing the necessary services for clients. These websites not only allow the users to access different collections of library resources, but also provide them with the necessary guidance in order to use the information. The goal of this study is the quality evaluation of the college library websites in Iranian Medical Universities based on the Stover model. This study uses an analytical survey method and is an applied study. The data gathering tool is the standard checklist provided by Stover, which was modified by the researchers for this study. The statistical population is the college library websites of the Iranian Medical Universities (146 websites) and census method was used for investigation. The data gathering method was a direct access to each website and filling of the checklist was based on the researchers' observations. Descriptive and analytical statistics (Analysis of Variance (ANOVA)) were used for data analysis with the help of the SPSS software. The findings showed that in the dimension of the quality of contents, the highest average belonged to type one universities (46.2%) and the lowest average belonged to type three universities (24.8%). In the search and research capabilities, the highest average belonged to type one universities (48.2%) and the lowest average belonged to type three universities. In the dimension of facilities provided for the users, type one universities again had the highest average (37.2%), while type three universities had the lowest average (15%). In general the library websites of type one universities had the highest quality (44.2%), while type three universities had the lowest quality (21.1%). Also the library websites of the College of Rehabilitation and the College of Paramedics, of the Shiraz University of Medical Science, had the highest quality scores. The results showed that there was a meaningful difference between the quality of the college library websites and the university types, resulting in college libraries of type one universities having the highest average score and the college libraries of type three universities having the lowest score.

Evaluation of the quality of the college library websites in Iranian medical Universities based on the Stover model

PubMed Central

Nasajpour, Mohammad Reza; Ashrafi-rizi, Hasan; Soleymani, Mohammad Reza; Shahrzadi, Leila; Hassanzadeh, Akbar

2014-01-01

Introduction: Today, the websites of college and university libraries play an important role in providing the necessary services for clients. These websites not only allow the users to access different collections of library resources, but also provide them with the necessary guidance in order to use the information. The goal of this study is the quality evaluation of the college library websites in Iranian Medical Universities based on the Stover model. Material and Methods: This study uses an analytical survey method and is an applied study. The data gathering tool is the standard checklist provided by Stover, which was modified by the researchers for this study. The statistical population is the college library websites of the Iranian Medical Universities (146 websites) and census method was used for investigation. The data gathering method was a direct access to each website and filling of the checklist was based on the researchers’ observations. Descriptive and analytical statistics (Analysis of Variance (ANOVA)) were used for data analysis with the help of the SPSS software. Findings: The findings showed that in the dimension of the quality of contents, the highest average belonged to type one universities (46.2%) and the lowest average belonged to type three universities (24.8%). In the search and research capabilities, the highest average belonged to type one universities (48.2%) and the lowest average belonged to type three universities. In the dimension of facilities provided for the users, type one universities again had the highest average (37.2%), while type three universities had the lowest average (15%). In general the library websites of type one universities had the highest quality (44.2%), while type three universities had the lowest quality (21.1%). Also the library websites of the College of Rehabilitation and the College of Paramedics, of the Shiraz University of Medical Science, had the highest quality scores. Discussion: The results showed that there was a meaningful difference between the quality of the college library websites and the university types, resulting in college libraries of type one universities having the highest average score and the college libraries of type three universities having the lowest score. PMID:25540794

Public Health and Social Desirability in Kazakhstan: Methodological Considerations

PubMed Central

Craig, Brett J.; Engstrom, Martha C.

2015-01-01

Background: As the Republic of Kazakhstan undertakes new public health efforts to promote healthy lifestyles among its citizens, the local perceptions of health and health behaviors need to be examined and understood from the sociocultural and historical perspectives. The primary aim of this study is to examine the association between perception of control on one’s health and engagement in good and bad health behaviors. Methods: Students enrolled in a health communication course surveyed 310 citizens of Kazakhstan on their perceptions of control over their own health and multiple health behaviors (i.e. smoking status, physical activity, etc.). Twenty-seven students were divided into groups and approached every third passerby as a potential participant during common shopping hours in nine popular marketplaces in Astana, Kazakhstan. Perception of control on one’s health was measured using a validated measure of health control: the multidimensional health locus of control scale (MHLC), developed by Wallston and colleagues. The MHLC measures three separate loci of control: internal, chance, and powerful others. Results: Participants perceived themselves as having highest control over their health (MHLC subscale internal: 29.70±0.64), powerful others had second highest control (MHLC subscale power others: 23.72±0.77), and chance had the lowest but still some control on their health (MHLC subscale chance: 20.82±0.85). Most participants rated their current health as very good (18.1%), good (45.0%), or moderate (32.3%). Approximately 23.4% of participants were smokers, and 22.2% consumed alcohol. Physical activity averaged 3.63 days in the past week, and fruit and vegetable consumption averaged 2 servings of each per day. Tobacco and the powerful others subscale were significantly negatively correlated (r=−0.17, p<0.05). Conclusions: Participant reports regarding personal health behaviors and lifestyle did not reflect the national reports regarding lifestyle behaviors. The relationship between powerful others subscale and tobacco smoking indicate that using healthcare providers may open up avenues to lowering tobacco use through patient education; however, social desirability is a notable concern for public health interventions. More importantly, the surveys uncovered future questions for conducting public health research with the general public, including issues of trust in the healthcare system and social desirability bias. Additional factors such as distrust in healthcare and government also may play a role in the public’s participation in social scientific research. The students who conducted the surveys reported a general skepticism from the public ranging from unfamiliarity with survey research to explicit distrust in the intentions and purpose of the research itself. PMID:29138719

Hydrodynamic Trails Produced by Daphnia: Size and Energetics

PubMed Central

Wickramarathna, Lalith N.; Noss, Christian; Lorke, Andreas

2014-01-01

This study focuses on quantifying hydrodynamic trails produced by freely swimming zooplankton. We combined volumetric tracking of swimming trajectories with planar observations of the flow field induced by Daphnia of different size and swimming in different patterns. Spatial extension of the planar flow field along the trajectories was used to interrogate the dimensions (length and volume) and energetics (dissipation rate of kinetic energy and total dissipated power) of the trails. Our findings demonstrate that neither swimming pattern nor size of the organisms affect the trail width or the dissipation rate. However, we found that the trail volume increases with increasing organism size and swimming velocity, more precisely the trail volume is proportional to the third power of Reynolds number. This increase furthermore results in significantly enhanced total dissipated power at higher Reynolds number. The biggest trail volume observed corresponds to about 500 times the body volume of the largest daphnids. Trail-averaged viscous dissipation rate of the swimming daphnids vary in the range of to and the observed magnitudes of total dissipated power between and , respectively. Among other zooplankton species, daphnids display the highest total dissipated power in their trails. These findings are discussed in the context of fluid mixing and transport by organisms swimming at intermediate Reynolds numbers. PMID:24671019

Muscle fibre conduction velocity during a 30-s Wingate anaerobic test.

PubMed

Stewart, David; Farina, Dario; Shen, Chao; Macaluso, Andrea

2011-06-01

Ten male volunteers (age 29.2 ± 5.2 years, mean ± SD) were recruited to test the hypothesis that muscle fibre conduction velocity (MFCV) would decrease with power output during a 30-s Wingate test on a mechanically-braked cycle ergometer. Prior to the main test, the optimal pre-fixed load corresponding to the highest power output was selected following a random series of six 10-s sprints. Surface electromyographic (EMG) signals were detected from the right vastus lateralis with linear adhesive arrays of eight electrodes. Power output decreased significantly from 6-s until the end of the test (860.9 ± 207.8 vs. 360.9 ± 11.4 W, respectively) and was correlated with MFCV (R=0.543, P<0.01), which also declined significantly by 26.8 ± 11% (P<0.05). There was a tendency for the mean frequency of the EMG power spectrum (MNF) to decrease, but average rectified values (ARV) remained unchanged throughout the test. The parallel decline of MFCV with power output suggests changes in fibre membrane properties. The unaltered ARV, together with the declined MFCV, would indicate either a decrease in discharge rate, de-recruitment of fatigued motor units or elongation of still present motor unit action potentials. Copyright © 2011 Elsevier Ltd. All rights reserved.

Single mode low-NA step index Yb-doped fiber design for output powers beyond 4kW (Conference Presentation)

NASA Astrophysics Data System (ADS)

Beier, Franz; Proske, Fritz; Hupel, Christian; Kuhn, Stefan; Hein, Sigrun; Sattler, Bettina; Nold, Johannes; Haarlammert, Nicoletta; Schreiber, Thomas; Eberhardt, Ramona; Tünnermann, Andreas

2017-03-01

Fiber amplifiers are representing one of the most promising solid state laser concepts, due to the compact setup size, a simple thermal management and furthermore excellent beam quality. In this contribution, we report on the latest results from a low-NA, large mode area single mode fiber with a single mode output power beyond 4 kW without any indication of mode instabilities or nonlinear effects and high slope efficiency. Furthermore, we quantify the influence of the bending diameter of our manufactured low NA fiber on the average core loss by an OFDR measurement and determine the optimal bending diameter in comparison to a second fiber with a slightly changed NA. The fibers used in the experiments were fabricated by MCVD technology combined with the solution doping technique. The investigation indicates the limitation of the step index fiber design and its influence on the use in high power fiber amplifiers. We demonstrate, that even a slightly change in the core NA crucially influences the minimum bending diameter of the fiber and has to be taken into account in applications. The measured output power represents to the best of our knowledge the highest single mode output power of an amplifier fiber ever reported on.

Performance ‘S’ Type Savonius Wind Turbine with Variation of Fin Addition on Blade

NASA Astrophysics Data System (ADS)

Pamungkas, S. F.; Wijayanto, D. S.; Saputro, H.; Widiastuti, I.

2018-01-01

Wind power has been receiving attention as the new energy resource in addressing the ecological problems of burning fossil fuels. Savonius wind rotor is a vertical axis wind turbines (VAWT) which has relatively simple structure and low operating speed. These characteristics make it suitable for areas with low average wind speed as in Indonesia. To identify the performance of Savonius rotor in generating electrical energy, this research experimentally studied the effect of fin addition for the ‘S’ shape of Savonius VAWT. The fin is added to fill the space in the blade in directing the wind flow. This rotor has two turbine blades, a rotor diameter of 1.1 m and rotor height of 1.4 m, used pulley transmission system with 1:4.2 multiplication ratio, and used a generator type PMG 200 W. The research was conducted during dry season by measuring the wind speed in the afternoon. The average wind speed in the area is 2.3 m/s with the maximum of 4.5 m/s. It was found that additional fin significantly increase the ability of Savonius rotor VAWT to generate electrical energy shown by increasing of electrical power. The highest power generated is 13.40 Watt at a wind speed of 4.5 m/s by adding 1 (one) fin in the blade. It increased by 22.71% from the rotor blade with no additional fin. However, increasing number of fins in the blade was not linearly increase the electrical power generated. The wind rotor blade with 4 additional fins is indicated has the lowest performance, generating only 10.80 Watt electrical power, accounted lower than the one generated by no fin-rotor blade. By knowing the effect of the rotor shape, the rotor dimension, the addition of fin, transmission, and generator used, it is possible to determine alternative geometry design in increasing the electrical power generated by Savonius wind turbine.

RS-25 Engines Powered to Highest Level Ever During Stennis Test

NASA Image and Video Library

2018-02-21

Operators powered NASA’s Space Launch System (SLS) engine to 113 percent thrust level, the highest RS-25 power level yet achieved, for 50 seconds of a 260-second test on February 21 at Stennis Space Center. This was the third full-duration test conducted on the A-1 Test Stand at Stennis this year.

RS-25 Engines Powered to Highest Level Ever during Stennis Test

NASA Image and Video Library

2018-02-21

Operators powered NASA’s Space Launch System (SLS) engine to 113 percent thrust level, the highest RS-25 power level yet achieved, for 50 seconds of a 260-second test on February 21 at Stennis Space Center. This was the third full-duration test conducted on the A-1 Test Stand at Stennis this year.

Large-area tungsten disulfide for ultrafast photonics.

PubMed

Yan, Peiguang; Chen, Hao; Yin, Jinde; Xu, Zihan; Li, Jiarong; Jiang, Zike; Zhang, Wenfei; Wang, Jinzhang; Li, Irene Ling; Sun, Zhipei; Ruan, Shuangchen

2017-02-02

Two-dimensional (2D) layered transition metal dichalcogenides (TMDs) have attracted significant interest in various optoelectronic applications due to their excellent nonlinear optical properties. One of the most important applications of TMDs is to be employed as an extraordinary optical modulation material (e.g., the saturable absorber (SA)) in ultrafast photonics. The main challenge arises while embedding TMDs into fiber laser systems to generate ultrafast pulse trains and thus constraints their practical applications. Herein, few-layered WS 2 with a large-area was directly transferred on the facet of the pigtail and acted as a SA for erbium-doped fiber laser (EDFL) systems. In our study, WS 2 SA exhibited remarkable nonlinear optical properties (e.g., modulation depth of 15.1% and saturable intensity of 157.6 MW cm -2 ) and was used for ultrafast pulse generation. The soliton pulses with remarkable performances (e.g., ultrashort pulse duration of 1.49 ps, high stability of 71.8 dB, and large pulse average output power of 62.5 mW) could be obtained in a telecommunication band. To the best of our knowledge, the average output power of the mode-locked pulse trains is the highest by employing TMD materials in fiber laser systems. These results indicate that atomically large-area WS 2 could be used as excellent optical modulation materials in ultrafast photonics.

Estimation of Bid Curves in Power Exchanges using Time-varying Simultaneous-Equations Models

NASA Astrophysics Data System (ADS)

Ofuji, Kenta; Yamaguchi, Nobuyuki

Simultaneous-equations model (SEM) is generally used in economics to estimate interdependent endogenous variables such as price and quantity in a competitive, equilibrium market. In this paper, we have attempted to apply SEM to JEPX (Japan Electric Power eXchange) spot market, a single-price auction market, using the publicly available data of selling and buying bid volumes, system price and traded quantity. The aim of this analysis is to understand the magnitude of influences to the auctioned prices and quantity from the selling and buying bids, than to forecast prices and quantity for risk management purposes. In comparison with the Ordinary Least Squares (OLS) estimation where the estimation results represent average values that are independent of time, we employ a time-varying simultaneous-equations model (TV-SEM) to capture structural changes inherent in those influences, using State Space models with Kalman filter stepwise estimation. The results showed that the buying bid volumes has that highest magnitude of influences among the factors considered, exhibiting time-dependent changes, ranging as broad as about 240% of its average. The slope of the supply curve also varies across time, implying the elastic property of the supply commodity, while the demand curve remains comparatively inelastic and stable over time.

Survey of electromagnetic field exposure in bedrooms of residences in lower Austria.

PubMed

Tomitsch, Johannes; Dechant, Engelbert; Frank, Wilhelm

2010-04-01

Previous investigations of exposure to electric, magnetic, or electromagnetic fields (EMF) in households were either about electricity supply EMFs or radio frequency EMFs (RF-EMFs). We report results from spot measurements at the bedside that comprise electrostatic fields, extremely low-frequency electric fields (ELF-EFs), extremely low-frequency magnetic fields (ELF-MFs), and RF-EMFs. Measurements were taken in 226 households throughout Lower Austria. In addition, effects of simple reduction measures (e.g., removal of clock radios or increasing their distance from the bed, turning off Digital Enhanced Cordless Telecommunication (DECT) telephone base stations) were assessed. All measurements were well below International Commission on Non-Ionizing Radiation Protection (ICNIRP) guideline levels. Average night-time ELF-MFs (long-term measurement from 10 pm to 6 am, geometric mean over households) above 100 nT were obtained in 2.3%, and RF-EMFs above 1000 microW/m(2) in 7.1% of households. Highest ELF-EFs were primarily due to lamps beside the bed (max = 166 V/m), and highest ELF-MFs because of transformers of devices (max = 1030 nT) or high current of power lines (max = 380 nT). The highest values of RF-EMFs were caused by DECT telephone base stations (max = 28979 microW/m(2)) and mobile phone base stations (max = 4872 microW/m(2)). Simple reduction measures resulted in an average decrease of 23 nT for ELF-MFs, 23 V/m for ELF-EFs, and 246 microW/m(2) for RF-EMFs. A small but statistically significant correlation between ELF-MF exposure and overall RF-EMF levels of R = 0.16 (P = 0.008) was computed that was independent of type (flat, single family) and location (urban, rural) of houses. (c) 2009 Wiley-Liss, Inc.

Long-term variations of aerosol optical depth and aerosol radiative forcing over Iran based on satellite and AERONET data.

PubMed

Arkian, F; Nicholson, S E

2017-12-01

In this study, three different sensors of satellites including the Moderate Resolution Imaging Spectroradiometer (MODIS), Multi-angle Imaging SpectroRadiometer (MISR), and Total Ozone Mapping Spectrometer (TOMS) were used to study spatial and temporal variations of aerosols over ten populated cities in Iran. Also, the Hybrid Single-Particle Lagrangian Integrated Trajectory (HYSPLIT) model was used for analyzing the origins of air masses and their trajectory in the area. An increasing trend in aerosol concentration was observed in the most studied cities in Iran during 1979-2016. The cities in the western part of Iran had the highest annual mean of aerosol concentration. The highest aerosol optical depth (AOD) value (0.76 ± 0.51) was recorded in May 2012 over Ahvaz, and the lowest value (0.035 ± 0.27) was recorded in December 2013 over Tabriz. After Ahvaz, the highest AOD value was found over Tehran (annual mean 0.11 ± 0.20). The results show that AOD increases with increasing industrial activities, but the increased frequency of aerosols due to land degradation and desertification is more powerful in Iran. The trajectory analysis by the HYSPLIT model showed that the air masses come from Egypt, Syria, and Lebanon and passed over the Iraq and then reached to Iran during summer. Aerosol radiative forcing (ARF) has been analyzed for Zanjan (Aerosol Robotic Network site) during 2010-2013. The ARF at surface and top of the atmosphere was found to be ranging from - 79 to - 10W m -2 (average - 33.45 W m -2 ) and from - 25 to 6 W m -2 (average - 12.80 W m -2 ), respectively.

Development of an Energy Harvesting Device using Piezoceramic Materials

NASA Astrophysics Data System (ADS)

Kulkarni, Vainatey

Piezoelectric energy harvesters are increasingly being pursued for their potential to replace finite-life batteries in wireless sensor modules and for their potential to create self-powered devices. This work presents the development of a novel piezoelectric harvester that attempts to improve upon the power output limitations of current piezoelectric harvesting technology. This novel harvester uses the concept of torsion on a tube to produce shear stresses and hence uses improved piezoelectric properties of the shear mode of piezoceramics to generate higher power outputs. This concept is first presented in this work and a proof-of-concept prototype is utilized to experimentally demonstrate the validity of this novel device. After this, the behaviour of the novel harvester is explored through an investigation into three cross-section geometries of the torsion tube and varying geometries of the eccentric mass using three different comparison metrics. Through this, it is observed that configurations with higher torsional compliance and high eccentric mass inertias have the potential for the highest power output and highest harvester effectiveness. However, the mechanical damping in the system is also found to significantly impact the harvester output resulting in prototypes of the various configurations not performing as expected. As a result of this discrepancy, the factors affecting the performance of the harvester are analyzed in greater detail through the development of a mathematical model that is then used to develop a set of guidelines to direct the design of a torsion harvester for a desired application. These guidelines are then used to develop an improved torsion harvester with a demonstrated ability to produce 1.2 mW of output power at its resonant frequency to power a wireless sensor module. Finally, the use of alternative materials such as single crystals of PMN-PT in the torsion harvester is also examined. Through finite element simulations and with material properties reported in the literature, the torsion harvester used with the sensor module is found to significantly benefit with the addition of the single crystal materials and ultimately generate 300% improvements in average output power while converting 11% of the input energy into usable electrical energy.

Photo-induced second-order nonlinearity in stoichiometric silicon nitride waveguides

NASA Astrophysics Data System (ADS)

Porcel, Marco A. G.; Mak, Jesse; Taballione, Caterina; Schermerhorn, Victoria K.; Epping, Jörn P.; van der Slot, Peter J. M.; Boller, Klaus-J.

2017-12-01

We report the observation of second-harmonic generation in stoichiometric silicon nitride waveguides grown via low-pressure chemical vapour deposition. Quasi-rectangular waveguides with a large cross section were used, with a height of 1 {\\mu}m and various different widths, from 0.6 to 1.2 {\\mu}m, and with various lengths from 22 to 74 mm. Using a mode-locked laser delivering 6-ps pulses at 1064 nm wavelength with a repetition rate of 20 MHz, 15% of the incoming power was coupled through the waveguide, making maximum average powers of up to 15 mW available in the waveguide. Second-harmonic output was observed with a delay of minutes to several hours after the initial turn-on of pump radiation, showing a fast growth rate between 10$^{-4}$ to 10$^{-2}$ s$^{-1}$, with the shortest delay and highest growth rate at the highest input power. After this first, initial build-up, the second-harmonic became generated instantly with each new turn-on of the pump laser power. Phase matching was found to be present independent of the used waveguide width, although the latter changes the fundamental and second-harmonic phase velocities. We address the presence of a second-order nonlinearity and phase matching, involving an initial, power-dependent build-up, to the coherent photogalvanic effect. The effect, via the third-order nonlinearity and multiphoton absorption leads to a spatially patterned charge separation, which generates a spatially periodic, semi-permanent, DC-field-induced second-order susceptibility with a period that is appropriate for quasi-phase matching. The maximum measured second-harmonic conversion efficiency amounts to 0.4% in a waveguide with 0.9 x 1 {\\mu}m$^2$ cross section and 36 mm length, corresponding to 53 {\\mu}W at 532 nm with 13 mW of IR input coupled into the waveguide. The according $\\chi^{(2)}$ amounts to 3.7 pm/V, as retrieved from the measured conversion efficiency.

Multi-Watt Average Power Nanosecond Microchip Laser and Power Scalability Estimates

NASA Technical Reports Server (NTRS)

Konoplev, Oleg A.; Vasilyev, Alexey A.; Seas, Antonios A.; Yu, Anthony W.; Li, Steven X.; Shaw, George B.; Stephen, Mark A.; Krainak, Michael A.

2011-01-01

We demonstrated up to 2 W average power, CW-pumped, passively- Q-switched, 1.5 ns monolithic MCL with single-longitudinal mode-operation. We discuss laser design issues to bring the average power to 5-1 OW and beyond.

Graphene saturable absorber mirror for ultra-fast-pulse solid-state laser.

PubMed

Xu, Jin-Long; Li, Xian-Lei; Wu, Yong-Zhong; Hao, Xiao-Peng; He, Jing-Liang; Yang, Ke-Jian

2011-05-15

High-quality graphene sheets with lateral size over 20 μm have been obtained by bath sonicating after subjecting the wormlike graphite marginally to mixed oxidizer. To date, to our knowledge, they are the largest graphene sheets prepared by exfoliation in the liquid phase. A saturable absorber mirror was fabricated based on these sheets. We exploited it to realize mode-locking operation in a diode-pumped Nd:GdVO(4) laser. A pulse duration of 16 ps was produced with an average power of 360 mW and a highest pulse energy of 8.4 nJ for a graphene mode-locked laser. © 2011 Optical Society of America

Objective criteria ranking framework for renewable energy policy decisions in Nigeria

NASA Astrophysics Data System (ADS)

K, Nwofor O.; N, Dike V.

2016-08-01

We present a framework that seeks to improve the objectivity of renewable energy policy decisions in Nigeria. It consists of expert ranking of resource abundance, resource efficiency and resource environmental comfort in the choice of renewable energy options for large scale power generation. The rankings are converted to a more objective function called Resource Appraisal Function (RAF) using dependence operators derived from logical relationships amongst the various criteria. The preferred option is that with the highest average RAF coupled with the least RAF variance. The method can be extended to more options, more criteria, and more opinions and can be adapted for similar decisions in education, environment and health sectors.

A study of the relationship between micropulsations and solar wind properties

NASA Technical Reports Server (NTRS)

Yedidia, B. A.; Lazarus, A. J.; Vellante, M.; Villante, U.

1991-01-01

A year-long comparison between daily averages of solar wind parameters obtained from the MIT experiment on IMP-8 and micropulsation measurements made by the Universita dell'Aquila has shown a correlation between solar wind speed and micropulsation power with peaks of the correlation coefficient greater than 0.8 in the period range from 20 to 40 s. Different behavior observed for different period bands suggests that the shorter period activity tends to precede the highest values of the solar wind speed while the longer period activity tends to persist for longer intervals within high velocity solar wind streams. A comparison with simultaneous interplanetary magnetic field measurements supports the upstream origin of the observed ground pulsations.

The application of pulse modulated plasma to the plasma enhanced chemical vapor deposition of dielectric materials

NASA Astrophysics Data System (ADS)

Qi, Yu

This dissertation work applied the pulse modulated plasma to the plasma enhanced chemical vapor deposition (PECVD) of two types of dielectric materials: SiO2-like coatings and Teflon-like coatings. SiO2-like coatings were firstly implemented with continuous plasma. It was proven that three different precursors: hexamethyldisiloxane (HMDSO), 1, 3, 5, 7-tetramethylcyclotetrasiloxane (TMCTS) and octamethylcyclotetrasiloxane (OMCTS) can be used to generate hard, clear and high density SiO2 deposition with coupled high growth rate and low processing temperature via PECVD. Under similar conditions, HMDSO has the lowest growth rate, lowest hardness and highest carbon content; TMCTS has the highest growth rate and hardness, and lowest carbon content; and OMCTS has moderate rates of these deposition qualities, but the best corrosion resistance. Substrate bias seems to have no effect on any deposition quality. High chamber pressure can significantly lower the carbon content in the thin films but does not affect any other qualities; the O2/precursor ratio is the most influential factor among all variables considered in this experiment. The deposition hardness and O:Si ratio always increase with this ratio while the carbon content always decreases. However, different precursors require different optimal ratios to achieve the highest growth rate. Pulse modulation was introduced into PECVD of SiO2-like coatings and OMCTS was selected as the precursor. It was demonstrated that pulse frequency, duty ratio and peak power have significant effects on deposition qualities. The proper combination of the pulse parameters and other traditional plasma parameters can significantly lower the processing temperature while retaining or even improving other deposition qualities, such as growth rate, corrosion resistance and elemental composition. Hardness is the only sacrifice of the lower time-average power caused by pulsing. Therefore, pulse modulation can effectively expand the possible range of combinations of desired deposition qualities. Finally, the pulsed plasma was used to implement PECVD of teflon-like coatings. An important discovery in this application is that in addition to pulse period, on-time and on-time peak power, the power level during the off-time is an important factor. The density of CF2 is a function of all these pulse parameters. The best result obtained is up to 67.2% CF2 and a 1.87:1 of F:C ratio when the off-time power level is ˜100--130 W the frequency is several Hz, the on-time peak power is ˜1000 W and the duty ratio is ˜7--10%.

Episodic air quality impacts of plug-in electric vehicles

NASA Astrophysics Data System (ADS)

Razeghi, Ghazal; Carreras-Sospedra, Marc; Brown, Tim; Brouwer, Jack; Dabdub, Donald; Samuelsen, Scott

2016-07-01

In this paper, the Spatially and Temporally Resolved Energy and Environment Tool (STREET) is used in conjunction with University of California Irvine - California Institute of Technology (UCI-CIT) atmospheric chemistry and transport model to assess the impact of deploying plug-in electric vehicles and integrating wind energy into the electricity grid on urban air quality. STREET is used to generate emissions profiles associated with transportation and power generation sectors for different future cases. These profiles are then used as inputs to UCI-CIT to assess the impact of each case on urban air quality. The results show an overall improvement in 8-h averaged ozone and 24-h averaged particulate matter concentrations in the South Coast Air Basin (SoCAB) with localized increases in some cases. The most significant reductions occur northeast of the region where baseline concentrations are highest (up to 6 ppb decrease in 8-h-averaged ozone and 6 μg/m3 decrease in 24-h-averaged PM2.5). The results also indicate that, without integration of wind energy into the electricity grid, the temporal vehicle charging profile has very little to no effect on urban air quality. With the addition of wind energy to the grid mix, improvement in air quality is observed while charging at off-peak hours compared to the business as usual scenario.

Validity of four approaches of using repeaters' MCAT scores in medical school admissions to predict USMLE Step 1 total scores.

PubMed

Zhao, Xiaohui; Oppler, Scott; Dunleavy, Dana; Kroopnick, Marc

2010-10-01

This study investigated the validity of four approaches (the average, most recent, highest-within-administration, and highest-across-administration approaches) of using repeaters' Medical College Admission Test (MCAT) scores to predict Step 1 scores. Using the differential predication method, this study investigated the magnitude of differences in the expected Step 1 total scores between MCAT nonrepeaters and three repeater groups (two-time, three-time, and four-time test takers) for the four scoring approaches. For the average score approach, matriculants with the same MCAT average are expected to achieve similar Step 1 total scores regardless of whether the individual attempted the MCAT exam one or multiple times. For the other three approaches, repeaters are expected to achieve lower Step 1 scores than nonrepeaters; for a given MCAT score, as the number of attempts increases, the expected Step 1 decreases. The effect was strongest for the highest-across-administration approach, followed by the highest-within-administration approach, and then the most recent approach. Using the average score is the best approach for considering repeaters' MCAT scores in medical school admission decisions.

Sensitivity of a phase-sensitive optical time-domain reflectometer with a semiconductor laser source

NASA Astrophysics Data System (ADS)

Alekseev, A. E.; Tezadov, Ya A.; Potapov, V. T.

2018-06-01

In the present paper we perform, for the first time, an analysis of the average sensitivity of a coherent phase-sensitive optical time-domain reflectometer (phase-OTDR) with a semiconductor laser source to external actions. The sensitivity of this OTDR can be defined in a conventional manner via average SNR at its output, which in turn is defined by the average useful signal power and the average intensity noise power in the OTDR spatial channels in the bandwidth defined by the OTDR sampling frequency. The average intensity noise power is considered in detail in a previous paper. In the current paper we examine the average useful signal power at the output of a phase-OTDR. The analysis of the average useful signal power of a phase-OTDR is based on the study of a fiber scattered-light interferometer (FSLI) which is treated as a constituent part of a phase- OTDR. In the analysis, one of the conventional phase-OTDR schemes with a rectangular dual-pulse probe signal is considered. The FSLI which corresponds to this OTDR scheme has two scattering fiber segments with additional time delay, introduced between backscattered fields. The average useful signal power and the resulting average SNR at the output of this FSLI are determined by the degree of coherence of the semiconductor laser source, the length of the scattering fiber segments, and by the additional time delay between the scattering fiber segments. The average useful signal power characteristic of the corresponding phase-OTDR is determined by analogous parameters: the source coherence, the time durations of the parts constituting the dual-pulse, and the time interval which separates these parts. In the paper an expression for the average useful signal power of a phase-OTDR is theoretically derived and experimentally verified. Based on the found average useful signal power of a phase-OTDR and the average intensity noise power, derived in the previous paper, the average SNR of a phase-OTDR is defined. Setting the average signal SNR to 1, at a defined spectral band the minimum detectable external action amplitude for our particular phase-OTDR setup is determined. We also derive a simple relation for the average useful signal power and the average SNR which results when making the assumption that the laser source coherence is high. The results of the paper can serve as the basis for further development of the concept of phase-OTDR sensitivity.

Detection of recurrent activation patterns across focal seizures: Application to seizure onset zone identification.

PubMed

Vila-Vidal, Manel; Principe, Alessandro; Ley, Miguel; Deco, Gustavo; Tauste Campo, Adrià; Rocamora, Rodrigo

2017-06-01

We introduce a method that quantifies the consistent involvement of intracranially monitored regions in recurrent focal seizures. We evaluated the consistency of two ictal spectral activation patterns (mean power change and power change onset time) in intracranial recordings across focal seizures from seven patients with clinically marked seizure onset zone (SOZ). We examined SOZ discrimination using both patterns in different frequency bands and periods of interest. Activation patterns were proved to be consistent across more than 80% of recurrent ictal epochs. In all patients, whole-seizure mean activations were significantly higher for SOZ than non-SOZ regions (P<0.05) while activation onset times were significantly lower for SOZ than for non-SOZ regions (P<0.001) in six patients. Alpha-beta bands (8-20Hz) achieved the highest patient-average effect size on the whole-seizure period while gamma band (20-70Hz) achieved the highest discrimination values between SOZ and non-SOZ sites near seizure onset (0-5s). Consistent spectral activation patterns in focal epilepsies discriminate the SOZ with high effect sizes upon appropriate selection of frequency bands and activation periods. The present method may be used to improve epileptogenic identification as well as pinpoint additional regions that are functionally altered during ictal events. Copyright © 2017 International Federation of Clinical Neurophysiology. Published by Elsevier B.V. All rights reserved.

Overview of Alcator C-Mod Research

NASA Astrophysics Data System (ADS)

White, A. E.

2017-10-01

Alcator C-Mod, a compact (R =0.68m, a =0.21m), high magnetic field, Bt <= 8T, tokamak accesses a variety of naturally ELM-suppressed high confinement regimes that feature extreme power density into the divertor, q|| <= 3 GW/m2, with SOL heat flux widths λq <0.5mm, exceeding conditions expected in ITER and approaching those foreseen in power plants. The unique parameter range provides much of the physics basis of a high-field, compact tokamak reactor. Research spans the topics of core transport and turbulence, RF heating and current drive, pedestal physics, scrape-off layer, divertor and plasma wall interactions. In the last experimental campaign, Super H-mode was explored and featured the highest pedestal pressures ever recorded, pped 90 kPa (90% of ITER target), consistent with EPED predictions. Optimization of naturally ELM-suppressed EDA H-modes accessed the highest volume averaged pressures ever achieved (〈p〉>2 atm), with pped 60 kPa. The SOL heat flux width has been measured at Bpol = 1.25T, confirming the Eich scaling over a broader poloidal field range than before. Multi-channel transport studies focus on the relationship between momentum transport and heat transport with perturbative experiments and new multi-scale gyrokinetic simulation validation techniques were developed. U.S. Department of Energy Grant No. DE-FC02-99ER54512.

Effect of timing of hip extension assistance during loaded walking with a soft exosuit.

PubMed

Ding, Ye; Panizzolo, Fausto A; Siviy, Christopher; Malcolm, Philippe; Galiana, Ignacio; Holt, Kenneth G; Walsh, Conor J

2016-10-03

Recent advances in wearable robotic devices have demonstrated the ability to reduce the metabolic cost of walking by assisting the ankle joint. To achieve greater gains in the future it will be important to determine optimal actuation parameters and explore the effect of assisting other joints. The aim of the present work is to investigate how the timing of hip extension assistance affects the positive mechanical power delivered by an exosuit and its effect on biological joint power and metabolic cost during loaded walking. In this study, we evaluated 4 different hip assistive profiles with different actuation timings: early-start-early-peak (ESEP), early-start-late-peak (ESLP), late-start-early-peak (LSEP), late-start-late-peak (LSLP). Eight healthy participants walked on a treadmill at a constant speed of 1.5 m · s -1 while carrying a 23 kg backpack load. We tested five different conditions: four with the assistive profiles described above and one unpowered condition where no assistance was provided. We evaluated participants' lower limb kinetics, kinematics, metabolic cost and muscle activation. The variation of timing in the hip extension assistance resulted in a different amount of mechanical power delivered to the wearer across conditions; with the ESLP condition providing a significantly higher amount of positive mechanical power (0.219 ± 0.006 W · kg -1 ) with respect to the other powered conditions. Biological joint power was significantly reduced at the hip (ESEP and ESLP) and at the knee (ESEP, ESLP and LSEP) with respect to the unpowered condition. Further, all assistive profiles significantly reduced the metabolic cost of walking compared to the unpowered condition by 5.7 ± 1.5 %, 8.5 ± 0.9 %, 6.3 ± 1.4 % and 7.1 ± 1.9 % (mean ± SE for ESEP, ESLP, LSEP, LSLP, respectively). The highest positive mechanical power delivered by the soft exosuit was reported in the ESLP condition, which showed also a significant reduction in both biological hip and knee joint power. Further, the ESLP condition had the highest average metabolic reduction among the powered conditions. Future work on autonomous hip exoskeletons may incorporate these considerations when designing effective control strategies.

Fully utilizing high power diode lasers by synergizing diode laser light sources and beam shaping micro-optics

NASA Astrophysics Data System (ADS)

Fan, Yingmin; Wang, Jingwei; Cai, Lei; Mitra, Thomas; Hauschild, Dirk; Zah, Chung-En; Liu, Xingsheng

2018-02-01

High power diode lasers (HPDLs) offer the highest wall-plug efficiency, highest specific power (power-to-weight ratio), arguably the lowest cost and highest reliability among all laser types. However, the poor beam quality of commercially HPDLs is the main bottleneck limiting their direct applications requiring high brightness at least in one dimension. In order to expand the applications of HPDLs, beam shaping and optical design are essential. In this work, we report the recent progresses on maximizing applications of HPDLs by synergizing diode laser light source and beam shaping micro-optics. Successful examples of matching of diode laser light sources and beam shaping micro-optics driving new applications are presented.

Agreement between child self-reported and parent-reported scores for chronic pain secondary to specific pediatric diseases.

PubMed

Díez Rodriguez-Labajo, A; Castarlenas, E; Miró, J; Reinoso-Barbero, F

2017-03-01

Parental report on a child's secondary chronic pain is commonly requested by anesthesiologists when the child cannot directly provide information. Daily pain intensity is reported as highest, average and lowest. However, it is unclear whether the parents' score is a valid indicator of the child's pain experience. Nineteen children (aged 6-18years) with secondary chronic pain attending our anesthesiologist-run pediatric pain unit participated in this study. Identification of highest, average and lowest pain intensity levels were requested during initial screening interviews with the child and parents. Pain intensity was scored on a 0-10 numerical rating scale. Agreement was examined using: (i) intraclass correlation coefficient (ICC), and (ii) the Bland-Altman method. The ICC's between the children and the parents' pain intensity reports were: 0.92 for the highest, 0.68 for the average, and 0.50 for the lowest pain intensity domains. The limits of agreement set at 95% between child and parental reports were respectively +2.19 to -2.07, +3.17 to -3.88 and +5.15 to -5.50 for the highest, average and lowest pain domains. For the highest pain intensity domain, agreement between parents and children was excellent. If replicated this preliminary finding would suggest the highest pain intensity is the easiest domain for reporting pain intensity when a child cannot directly express him or herself. Copyright © 2016 Sociedad Española de Anestesiología, Reanimación y Terapéutica del Dolor. Publicado por Elsevier España, S.L.U. All rights reserved.

Overweight and pregnancy complications.

PubMed

Abrams, B; Parker, J

1988-01-01

The association between increased prepregnancy weight for height and seven pregnancy complications was studied in a multi-racial sample of more than 4100 recent deliveries. Body mass indices were calculated and used to classify women as average weight (90-119 percent of ideal or BMI 19.21-25.60), moderately overweight (120-135 percent ideal or BMI 25.61-28.90), and very overweight (greater than 135 percent ideal or BMI greater than 28.91) prior to pregnancy. Compared to women of average weight for height, very overweight women had a higher risk of diabetes, hypertension, pregnancy-induced hypertension and primary cesarean section delivery. Moderately overweight women were also at higher risk than average for diabetes, pregnancy-induced hypertension and primary cesarean deliveries but the relative risks were of a smaller magnitude than for very overweight women. With women of average prepregnancy body mass as reference, moderately elevated, but not significant relative risks were found for perinatal mortality in the very overweight group, for urinary tract infections in both overweight groups, and a decreased risk for anemia was found in the very overweight group. However, post-hoc power analyses indicated that the number of overweight women in the sample did not allow adequate statistical power to detect these small differences in risk. To overcome limitations associated with low statistical power, the results of three recent studies of these outcomes in very overweight pregnant women were combined and summarized using Mantel-Haenzel techniques. This second, larger analysis suggested that very overweight women are at significantly higher risk for all seven outcomes studied. Summary results for moderately overweight women could not be calculated, since only two of the studies had evaluated moderately overweight women separately. These latter results support other findings that both moderate overweight and very overweight are risk factors during pregnancy, with the highest risk occurring in the heaviest group. Although these results indicate that moderate overweight is a risk factor during pregnancy, additional studies are needed to confirm the impact of being 20-35 percent above ideal weight prior to pregnancy. The results of this analysis also imply that since the baseline incidence of many perinatal complications is low, studies relating overweight and pregnancy complications should include large enough samples of overweight women so that there is adequate statistical power to reliably detect differences in complication rates.

Less Physician Practice Competition Is Associated With Higher Prices Paid For Common Procedures.

PubMed

Austin, Daniel R; Baker, Laurence C

2015-10-01

Concentration among physician groups has been steadily increasing, which may affect prices for physician services. We assessed the relationship in 2010 between physician competition and prices paid by private preferred provider organizations for fifteen common, high-cost procedures to understand whether higher concentration of physician practices and accompanying increased market power were associated with higher prices for services. Using county-level measures of the concentration of physician practices and county average prices, and statistically controlling for a range of other regional characteristics, we found that physician practice concentration and prices were significantly associated for twelve of the fifteen procedures we studied. For these procedures, counties with the highest average physician concentrations had prices 8-26 percent higher than prices in the lowest counties. We concluded that physician competition is frequently associated with prices. Policies that would influence physician practice organization should take this into consideration. Project HOPE—The People-to-People Health Foundation, Inc.

Numerical study of a cryogen-free vuilleumier type pulse tube cryocooler operating below 10 K

NASA Astrophysics Data System (ADS)

Wang, Y. N.; Wang, X. T.; Dai, W.; Luo, E. C.

2017-12-01

This paper presents a numerical investigation on a Vuilleumier (VM) type pulse tube cooler. Different from previous systems that use liquid nitrogen, Stirling type pre-coolers are used to provide the cooling power for the thermal compressor, which leads to a convenient cryogen-free system and offers the flexibility of changing working temperature range of the thermal compressor to obtain an optimum efficiency. Firstly, main component dimensions were optimized with lowest no-load temperature as the target. Then the dependence of system performance on average pressure, frequency, displacer displacement amplitude and thermal compressor pre-cooling temperature were studied. Finally, the effect of pre-cooling temperature on overall cooling efficiency at 5 K was studied. A highest relative Carnot efficiency of 0.82 % was predicted with an average pressure of 2.5 MPa, a frequency of 3 Hz, a displacer displacement amplitude of 6.5 mm, ambient end temperature 300 K and pre-cooling temperature 65 K, respectively.

Socioeconomic factors and mortality in urban settings: the case of Barcelona, Spain.

PubMed Central

Borrell, C; Arias, A

1995-01-01

STUDY OBJECTIVE--This study aimed to describe the relationship between health and socioeconomic indicators in the 38 neighbourhoods of the city of Barcelona, Spain. DESIGN--Mortality data for 1983-89 and socioeconomic data for each of the 38 neighbourhoods of Barcelona were used. Mortality indicators used were the comparative mortality figure, the ratio of potential years of life lost, and life expectancy at birth. Socioeconomic indicators were the percentage of unemployed, the percentage of illiteracy, monthly telephone usage, the average power and age of cars, and the average rateable value of buildings and of land. The statistical correlation between socioeconomic indicators and mortality indicators was studied by Spearman's rank correlation coefficient. SETTING--The 38 neighbourhoods of Barcelona, Spain. MEASUREMENTS AND MAIN RESULTS--The comparative mortality figure ranged from 87.41-152.43 and the ratio of potential years of life lost from 74.94-237.31 in both sexes. Both the absolute difference and the ratio of the value for the neighbourhood with lowest mortality and that with highest mortality were larger when premature mortality was examined. Life expectancy at birth ranged from 64.77-75.32 years in men and 75.04-81.51 in women. All correlations between mortality and socioeconomic indicators were high and statistically significant: the higher the unemployment and illiteracy levels and the older the cars, the greater the comparative mortality figure and ratio of potential years of life lost, and the lower the life expectancy (negative correlations). Conversely, the higher the telephone use, the more powerful the cars, and the greater the rateable value, the lower the mortality (negative correlations) and the greater the life expectancy. These correlations were greater in males than in females. The highest correlations were with illiteracy. CONCLUSIONS--This study has detected significant differences in mortality in a large town in the Mediterranean region of Europe. Images PMID:7499987

Numerical study of a confined slot impinging jet with nanofluids

PubMed Central

2011-01-01

Background Heat transfer enhancement technology concerns with the aim of developing more efficient systems to satisfy the increasing demands of many applications in the fields of automotive, aerospace, electronic and process industry. A solution for obtaining efficient cooling systems is represented by the use of confined or unconfined impinging jets. Moreover, the possibility of increasing the thermal performances of the working fluids can be taken into account, and the introduction of nanoparticles in a base fluid can be considered. Results In this article, a numerical investigation on confined impinging slot jet working with a mixture of water and Al2O3 nanoparticles is described. The flow is turbulent and a constant temperature is applied on the impinging. A single-phase model approach has been adopted. Different geometric ratios, particle volume concentrations and Reynolds number have been considered to study the behavior of the system in terms of average and local Nusselt number, convective heat transfer coefficient and required pumping power profiles, temperature fields and stream function contours. Conclusions The dimensionless stream function contours show that the intensity and size of the vortex structures depend on the confining effects, given by H/W ratio, Reynolds number and particle concentrations. Furthermore, for increasing concentrations, nanofluids realize increasing fluid bulk temperature, as a result of the elevated thermal conductivity of mixtures. The local Nusselt number profiles show the highest values at the stagnation point, and the lowest at the end of the heated plate. The average Nusselt number increases for increasing particle concentrations and Reynolds numbers; moreover, the highest values are observed for H/W = 10, and a maximum increase of 18% is detected at a concentration equal to 6%. The required pumping power as well as Reynolds number increases and particle concentrations grow, which is almost 4.8 times greater than the values calculated in the case of base fluid. List of symbols PMID:21711743

Total mercury in canned tuna sold in Canada in 2006.

PubMed

Dabeka, Robert W; Mckenzie, Arthur D; Forsyth, Donald S

2014-01-01

Total mercury was measured in 156 composites prepared from 936 samples of canned tuna sold in Canada in 2006. Each composite comprised a single brand. Yellowfin tuna contained the lowest concentrations, averaging 0.066 mg/kg. Skipjack tuna contained slightly higher concentrations, averaging 0.132 mg/kg. The highest average concentration was found in the Albacore tuna: mean 0.325 mg/kg, range 0.174-0.507 mg/kg. The second highest concentration among the 49 albacore composites was 0.469 mg/kg. There were 72 composites for which the type of tuna was not specified. The mercury in these averaged 0.095 mg/kg and ranged from 0.016 to 0.237 mg/kg.

338-GHz Semiconductor Amplifier Module

NASA Technical Reports Server (NTRS)

Samoska, Lorene A.; Gaier, Todd C.; Soria, Mary M.; Fung, King Man; Rasisic, Vesna; Deal, William; Leong, Kevin; Mei, Xiao Bing; Yoshida, Wayne; Liu, Po-Hsin;

The application of photovoltaic roof shingles to residential and commercial buildings

NASA Technical Reports Server (NTRS)

Shepard, N. F., Jr.; Sanchez, L. E.

1978-01-01

The recent development of a shingle-type solar-cell module makes it possible to incorporate easily photovoltaic power generation into the sloping roofs of residential or commercial buildings. These modules, which use a closely packed array of nineteen 53-mm-diameter circular solar cells, are capable of producing 101 watts/sq m of module area under standard operating conditions. This module performance is achievable by the use of solar cells with an average efficiency of 13.3 percent at 1 kW/sq m air-mass-1.5 insolation and at a cell temperature of 28 C. When these modules are mounted on a sloping south-facing roof which is insulated on the rear surface, the annual energy generated at the maximum power operating point will vary from 255.6 to 137.3 kWh/sq m of module area depending on the site location, with Albuquerque, NM, and Seattle, WA, representing the highest and lowest values of the thirteen sites considered.

Aging analysis of high performance FinFET flip-flop under Dynamic NBTI simulation configuration

NASA Astrophysics Data System (ADS)

Zainudin, M. F.; Hussin, H.; Halim, A. K.; Karim, J.

2018-03-01

A mechanism known as Negative-bias Temperature Instability (NBTI) degrades a main electrical parameters of a circuit especially in terms of performance. So far, the circuit design available at present are only focussed on high performance circuit without considering the circuit reliability and robustness. In this paper, the main circuit performances of high performance FinFET flip-flop such as delay time, and power were studied with the presence of the NBTI degradation. The aging analysis was verified using a 16nm High Performance Predictive Technology Model (PTM) based on different commands available at Synopsys HSPICE. The results shown that the circuit under the longer dynamic NBTI simulation produces the highest impact in the increasing of gate delay and decrease in the average power reduction from a fresh simulation until the aged stress time under a nominal condition. In addition, the circuit performance under a varied stress condition such as temperature and negative stress gate bias were also studied.

Semiconductor saturable absorber mirror passively Q-switched 2.97 μm fluoride fiber laser

NASA Astrophysics Data System (ADS)

Li, Jianfeng; Luo, Hongyu; He, Yulian; Liu, Yong; Luo, Binbin; Sun, Zhongyuan; Zhang, Lin; Turitsyn, Sergei K.

2014-05-01

A diode-cladding-pumped mid-infrared passively Q-switched Ho3+-doped fluoride fiber laser using a reverse designed broad band semiconductor saturable mirror (SESAM) was demonstrated. Nonlinear reflectivity of the SESAM was measured using an in-house Yb3+-doped mode-locked fiber laser at 1062 nm. Stable pulse train was produced at a slope efficient of 12.1% with respect to the launched pump power. Maximum pulse energy of 6.65 μJ with a pulse width of 1.68 μs and signal to noise ratio (SNR) of ~50 dB was achieved at a repetition rate of 47.6 kHz and center wavelength of 2.971 μm. To the best of our knowledge, this is the first 3 μm region SESAM based Q-switched fiber laser with the highest average power and pulse energy, as well as the longest wavelength from mid-infrared passively Q-switched fluoride fiber lasers.

Semiconductor saturable absorber mirror passively Q-switched 2.97 μm fluoride fiber laser

NASA Astrophysics Data System (ADS)

Li, J. F.; Luo, H. Y.; He, Y. L.; Liu, Y.; Zhang, L.; Zhou, K. M.; Rozhin, A. G.; Turistyn, S. K.

2014-06-01

A diode-cladding-pumped mid-infrared passively Q-switched Ho3+-doped fluoride fiber laser using a reverse designed broad band semiconductor saturable mirror (SESAM) was demonstrated. Nonlinear reflectivity of the SESAM was measured using an in-house Yb3+-doped mode-locked fiber laser at 1062 nm. Stable pulse train was produced at a slope efficient of 12.1% with respect to the launched pump power. Maximum pulse energy of 6.65 µJ with a pulse width of 1.68 µs and signal-to-noise ratio (SNR) of ~50 dB was achieved at a repetition rate of 47.6 kHz and center wavelength of 2.971 µm. To the best of our knowledge, this is the first 3 µm region SESAM-based Q-switched fiber laser with the highest average power and pulse energy, as well as the longest wavelength from mid-infrared passively Q-switched fluoride fiber lasers.

Evaluation of Wind Energy Production in Texas using Geographic Information Systems (GIS)

NASA Astrophysics Data System (ADS)

Ferrer, L. M.

2017-12-01

Texas has the highest installed wind capacity in the United States. The purpose of this research was to estimate the theoretical wind turbine energy production and the utilization ratio of wind turbines in Texas. Windfarm data was combined applying Geographic Information System (GIS) methodology to create an updated GIS wind turbine database, including location and technical specifications. Applying GIS diverse tools, the windfarm data was spatially joined with National Renewable Energy Laboratory (NREL) wind data to calculate the wind speed at each turbine hub. The power output for each turbine at the hub wind speed was evaluated by the GIS system according the respective turbine model power curve. In total over 11,700 turbines are installed in Texas with an estimated energy output of 60 GWh per year and an average utilization ratio of 0.32. This research indicates that applying GIS methodologies will be crucial in the growth of wind energy and efficiency in Texas.

Physiological characteristics of an aging Olympic athlete.

PubMed

Nybo, Lars; Schmidt, Jakob F; Fritzdorf, Stephen; Nordsborg, Nikolai B

2014-11-01

To investigate the physiological basis of continued world-class performance of a world-class rower who won medals (three gold and two bronze) at five consecutive Olympic Games. From the age of 19 to 40 yr, maximal oxygen uptake (VO2 max), peak HR, blood lactate, and rowing ergometer performance were assessed annually. During the first years of his elite career (from age 19 to 24), VO2 max increased from 5.5 to approximately 5.9 L · min(-1) (78 mL · min(-1) · kg(-1)) and his average power during 6-min maximal rowing increased from 420 to approximately 460 W. Although his HRmax declined by approximately 20 bpm during the 20-yr period, maximal aerobic power, evaluated both as VO2 max and 6-min test performance, was maintained until the age of 40. Furthermore, peak lactate levels remained unchanged and average power outputs during 10-s, 60-s, and 60-min ergometer tests were all maintained at approximately 800 W, approximately 700 W, and approximately 350 W, respectively, indicating that he was able to preserve both aerobic and anaerobic exercise performances. Echocardiographic analyses revealed a left ventricular mass of 198 g and left ventricular end-diastolic diameter of 5.8 cm. This longitudinal case indicates that until the age of 40 yr, a steady increase in the oxygen pulse may have compensated for the significant decline in the maximal heart frequency. Furthermore, the maintenance of aerobic and anaerobic exercise capacities allowed this Olympic athlete to compete at the highest level for almost two decades.

High power infrared QCLs: advances and applications

NASA Astrophysics Data System (ADS)

Patel, C. Kumar N.

2012-01-01

QCLs are becoming the most important sources of laser radiation in the midwave infrared (MWIR) and longwave infrared (LWIR) regions because of their size, weight, power and reliability advantages over other laser sources in the same spectral regions. The availability of multiwatt RT operation QCLs from 3.5 μm to >16 μm with wall plug efficiency of 10% or higher is hastening the replacement of traditional sources such as OPOs and OPSELs in many applications. QCLs can replace CO2 lasers in many low power applications. Of the two leading groups in improvements in QCL performance, Pranalytica is the commercial organization that has been supplying the highest performance QCLs to various customers for over four year. Using a new QCL design concept, the non-resonant extraction [1], we have achieved CW/RT power of >4.7 W and WPE of >17% in the 4.4 μm - 5.0 μm region. In the LWIR region, we have recently demonstrated QCLs with CW/RT power exceeding 1 W with WPE of nearly 10 % in the 7.0 μm-10.0 μm region. In general, the high power CW/RT operation requires use of TECs to maintain QCLs at appropriate operating temperatures. However, TECs consume additional electrical power, which is not desirable for handheld, battery-operated applications, where system power conversion efficiency is more important than just the QCL chip level power conversion efficiency. In high duty cycle pulsed (quasi-CW) mode, the QCLs can be operated without TECs and have produced nearly the same average power as that available in CW mode with TECs. Multiwatt average powers are obtained even in ambient T>70°C, with true efficiency of electrical power-to-optical power conversion being above 10%. Because of the availability of QCLs with multiwatt power outputs and wavelength range covering a spectral region from ~3.5 μm to >16 μm, the QCLs have found instantaneous acceptance for insertion into multitude of defense and homeland security applications, including laser sources for infrared countermeasures for protecting aircraft from MANPADS, testing of infrared countermeasures, MWIR and LWIR lasers for identify-friend-or-foe (IFF) personnel beacons, infrared target illuminators and designators and tunable QCL applications including in-situ and standoff detection of chemical warfare agents (CWAs) and explosives. The last of these applications addresses a very important and timely need for detection of improvised explosive devices (IEDs) in combat environments like Iraq and Afghanistan.

Focus on Teacher Salaries: What Teacher Salary Averages Don't Show.

ERIC Educational Resources Information Center

Gaines, Gale

Traditional comparisons of teacher salary averages fail to consider factors beyond pay raises that affect those averages. Salary averages do not show: regional and national variations among states' average salaries; the variation of salaries within an individual state; variations in the cost of living; the highest degree earned by teachers and the…

Ultrastable, high efficiency picosecond green light generation using K3B6O10Br series nonlinear optical crystals

NASA Astrophysics Data System (ADS)

Hou, Z. Y.; Xia, M. J.; Wang, L. R.; Xu, B.; Yan, D. X.; Meng, L. P.; Liu, L. J.; Xu, D. G.; Zhang, L.; Wang, X. Y.; Li, R. K.; Chen, C. T.

2017-09-01

Two perovskite-structure K3B6O10Br1-x Cl x (x  =  0 and 0.5) series nonlinear optical crystals were thoroughly investigated for their picosecond 532 nm laser pulses abilities and high power outputs were achieved via second harmonic generation (SHG) technique for the first time. SHG conversion efficiency of 57.3% with a 13.2 mm length K3B6O10Br (KBB) crystal was achieved using a laser source of pulse repetition rate of 10 Hz and pulse width of 25 ps, which is the highest conversion efficiency of ps visible laser based on KBB crystal. And by employing an 80 MHz, 10 ps fundamental laser beam, maximum power outputs of 12 W with K3B6O10Br0.5Cl0.5 (KBBC) and 11.86 W with KBB crystals were successfully demonstrated. Furthermore, the standard deviation jitters of the average power outputs are less than 0.6% and 1.17% by KBB and KBBC, respectively, showing ultrastable power stabilities favorable for practical applications. In addition, the other optical parameters including acceptance angle and temperature bandwidth were also investigated.

An OFDM System Using Polyphase Filter and DFT Architecture for Very High Data Rate Applications

NASA Technical Reports Server (NTRS)

Kifle, Muli; Andro, Monty; Vanderaar, Mark J.

2001-01-01

This paper presents a conceptual architectural design of a four-channel Orthogonal Frequency Division Multiplexing (OFDM) system with an aggregate information throughput of 622 megabits per second (Mbps). Primary emphasis is placed on the generation and detection of the composite waveform using polyphase filter and Discrete Fourier Transform (DFT) approaches to digitally stack and bandlimit the individual carriers. The four-channel approach enables the implementation of a system that can be both power and bandwidth efficient, yet enough parallelism exists to meet higher data rate goals. It also enables a DC power efficient transmitter that is suitable for on-board satellite systems, and a moderately complex receiver that is suitable for low-cost ground terminals. The major advantage of the system as compared to a single channel system is lower complexity and DC power consumption. This is because the highest sample rate is half that of the single channel system and synchronization can occur at most, depending on the synchronization technique, a quarter of the rate of a single channel system. The major disadvantage is the increased peak-to-average power ratio over the single channel system. Simulation results in a form of bit-error-rate (BER) curves are presented in this paper.

Analysis of micromineral contents of school meals.

PubMed

Shin, Dongsoon

2014-08-01

Korean ordinary diets are referred to be good for human health in worldwide. However it is uncertain whether they provide microminerals enough for growth and health of teenagers. A main purpose of this study was to identify micromineral contents in school meals. The fifty cuisines were collected from elementary schools and middle schools in Gyeongnam area. The contents of Fe, Zn, Cu and Mn among microminerals were analyzed by using ICP-OES method. Data were expressed as mean, standard deviation and range value and linear regression analysis performed. Fe level of Pangibuseotpaprika-salad was the highest among side-dishes (average 346.6 µg) and Zn level of Sullung-tang was highest among soups (average 229.1 µg). Cu level of Buchu-kimchi was the highest among kimchies (average 217.5 µg) and Mn level of Gumeunkongyangnyum-gui was highest among side-dishes (average 198.4 µg). Generally cooked-rices as main dish had relative smaller amounts of microminerals than the other cuisines. The results showed that the ratio of Cu : Fe : Zn was approximately 12 : 4 : 1 and the relationship between Fe versus Zn or Fe versus Cu was significantly positive. Comparing to Korean Dietary Recommended Intakes (KDRI) level, school meals provided not sufficient amount (<25% DRI) of Fe, Zn or Mn, while they did excessive amount (>125% DRI) of Cu.

Hydrodynamic trails produced by Daphnia: size and energetics.

PubMed

Wickramarathna, Lalith N; Noss, Christian; Lorke, Andreas

2014-01-01

This study focuses on quantifying hydrodynamic trails produced by freely swimming zooplankton. We combined volumetric tracking of swimming trajectories with planar observations of the flow field induced by Daphnia of different size and swimming in different patterns. Spatial extension of the planar flow field along the trajectories was used to interrogate the dimensions (length and volume) and energetics (dissipation rate of kinetic energy and total dissipated power) of the trails. Our findings demonstrate that neither swimming pattern nor size of the organisms affect the trail width or the dissipation rate. However, we found that the trail volume increases with increasing organism size and swimming velocity, more precisely the trail volume is proportional to the third power of Reynolds number. This increase furthermore results in significantly enhanced total dissipated power at higher Reynolds number. The biggest trail volume observed corresponds to about 500 times the body volume of the largest daphnids. Trail-averaged viscous dissipation rate of the swimming daphnids vary in the range of 1.8 x 10(-6) W/kg to 3.4 x 10(-6) W/kg and the observed magnitudes of total dissipated power between 1.3 x 10(-9) W and 1 x 10(-8) W, respectively. Among other zooplankton species, daphnids display the highest total dissipated power in their trails. These findings are discussed in the context of fluid mixing and transport by organisms swimming at intermediate Reynolds numbers.

Selective effects of different fatigue protocols on the function of upper body muscles assessed through the force-velocity relationship.

PubMed

García-Ramos, Amador; Torrejón, Alejandro; Feriche, Belén; Morales-Artacho, Antonio J; Pérez-Castilla, Alejandro; Padial, Paulino; Jaric, Slobodan

2018-02-01

This study explored the feasibility of the force-velocity relationship (F-V) to detect the acute effects of different fatigue protocols on the selective changes of the maximal capacities of upper body muscles to produce force, velocity, and power. After determining the bench press one-repetition maximum (1RM), participants' F-V relationships were assessed during the bench press throw exercise on five separate sessions after performing one of the following fatiguing protocols: 60%1RM failure, 60%1RM non-failure, 80%1RM failure, 80%1RM non-failure, and no-fatigue. In the non-failure protocols, participants performed half the maximum number of repetitions than in their respective failure protocols. The main findings revealed that (1) all F-V relationships were highly linear (median r = 0.997 and r = 0.982 for averaged across participants and individual data, respectively), (2) the fatiguing protocols were ranked based on the magnitude of power loss as follows: 60%1RM failure > 80%1RM failure > 60%1RM non-failure > 80%1RM non-failure, while (3) the assessed maximum force and velocity outputs showed a particularly prominent reduction in the protocols based on the lowest and highest levels of fatigue (i.e., 80%1RM non-failure and 60%1RM failure), respectively. The results support the use of F-V to assess the effects of fatigue on the distinctive capacities of the muscles to produce force, velocity, and power output while performing multi-joint tasks, while the assessed maximum force and velocity capacities showed a particularly prominent reduction in the protocols based on the lowest and highest levels of fatigue (i.e., 80%1RM non-failure and 60%1RM failure), respectively.

Concerns and perceptions immediately following Superstorm Sandy: ratings for property damage were higher than for health issues

PubMed Central

Burger, Joanna; Gochfeld, Michael

2015-01-01

Governmental officials, health and safety professionals, early responders, and the public are interested in the perceptions and concerns of people faced with a crisis, especially during and immediately after a disaster strikes. Reliable information can lead to increased individual and community preparedness for upcoming crises. The objective of this research was to evaluate concerns of coastal and central New Jersey residents within the first 100 days of Superstorm Sandy’s landfall. Respondents living in central New Jersey and Jersey shore communities were differentially impacted by the storm, with shore residents having higher evacuation rates (47% vs. 13%), more flood waters in their homes, longer power outages (average 23 vs. 6 days), and longer periods without Internet (29 vs. 6 days). Ratings of concerns varied both among and within categories as a function of location (central vs. coastal New Jersey), stressor level (ranging from 1 to 3 for combinations of power outages, high winds, and flooding), and demographics. Respondents were most concerned about property damage, health, inconveniences, ecological services, and nuclear power plants in that order. Respondents from the shore gave higher ratings to the concerns within each major category, compared to those from central Jersey. Four findings have implications for understanding future risk, recovery, and resiliency: (1) respondents with the highest stressor level (level 3) were more concerned about water damage than others, (2) respondents with flood damage were more concerned about water drainage and mold than others, (3) respondents with the highest stressor levels rated all ecological services higher than others, and (4) shore respondents rated all ecological services higher than central Jersey residents. These data provide information to design future preparedness plans, improve resiliency for future severe weather events, and reduce public health risk. PMID:27011757

Entropy production and optimization of geothermal power plants

NASA Astrophysics Data System (ADS)

Michaelides, Efstathios E.

2012-09-01

Geothermal power plants are currently producing reliable and low-cost, base load electricity. Three basic types of geothermal power plants are currently in operation: single-flashing, dual-flashing, and binary power plants. Typically, the single-flashing and dual-flashing geothermal power plants utilize geothermal water (brine) at temperatures in the range of 550-430 K. Binary units utilize geothermal resources at lower temperatures, typically 450-380 K. The entropy production in the various components of the three types of geothermal power plants determines the efficiency of the plants. It is axiomatic that a lower entropy production would improve significantly the energy utilization factor of the corresponding power plant. For this reason, the entropy production in the major components of the three types of geothermal power plants has been calculated. It was observed that binary power plants generate the lowest amount of entropy and, thus, convert the highest rate of geothermal energy into mechanical energy. The single-flashing units generate the highest amount of entropy, primarily because they re-inject fluid at relatively high temperature. The calculations for entropy production provide information on the equipment where the highest irreversibilities occur, and may be used to optimize the design of geothermal processes in future geothermal power plants and thermal cycles used for the harnessing of geothermal energy.

Flavanols, proanthocyanidins and antioxidant activity changes during cocoa (Theobroma cacao L.) roasting as affected by temperature and time of processing.

PubMed

Ioannone, F; Di Mattia, C D; De Gregorio, M; Sergi, M; Serafini, M; Sacchetti, G

2015-05-01

The effect of roasting on the content of flavanols and proanthocyanidins and on the antioxidant activity of cocoa beans was investigated. Cocoa beans were roasted at three temperatures (125, 135 and 145 °C), for different times, to reach moisture contents of about 2 g 100 g(-1). Flavanols and proanthocyanidins were determined, and the antioxidant activity was tested by total phenolic index (TPI), ferric reducing antioxidant power (FRAP) and total radical trapping antioxidant parameter (TRAP) methods. The rates of flavanol and total proanthocyanidin loss increased with roasting temperatures. Moisture content of the roasted beans being equal, high temperature-short time processes minimised proanthocyanidins loss. Moisture content being equal, the average roasting temperature (135 °C) determined the highest TPI and FRAP values and the highest temperature (145 °C) determined the lowest TPI values. Moisture content being equal, low temperature-long time roasting processes maximised the chain-breaking activity, as determined by the TRAP method. Copyright © 2014 Elsevier Ltd. All rights reserved.

Low flows and water temperature risks to Asian coal power plants in a warming world

NASA Astrophysics Data System (ADS)

Wang, Y.; Byers, E.; Parkinson, S.; Wanders, N.; Wada, Y.; Bielicki, J. M.

2017-12-01

Thermoelectric power generation requires cooling, normally provided by wet cooling systems. The withdrawal and discharge of cooling water are subject to regulation. Therefore, operation of power plants may be vulnerable to changes in streamflow and rises in water temperatures. In Asia, about 489 GW of coal-fired power plants are currently under construction, permitted, or announced. Using a comprehensive dataset of these planned coal power plants (PCPPs) and cooling water use models, we investigated whether electricity generation at these power plants will be limited by streamflow and water temperature. Daily streamflow and water temperature time series are from the high-resolution (0.08ox0.08o) runs of the PCRGLOBWB hydrological model, driven by downscaled meteorological forcing from five global climate models. We compared three climate change scenarios (1.5oC, 2oC, and 3oC warming in global mean temperature) and three cooling system choice scenarios (freshwater once-through, freshwater cooling tower, and "business-as-usual" - where a PCPP uses the same cooling system as the nearest existing coal power plant). The potential available capacity of the PCPPs increase slightly from the 1.5oC to the 2oC and 3oC warming scenario due to increase in streamflow. The once-through cooling scenario results in virtually zero available capacity at the PCPPs. The other two cooling scenarios result in about 20% of the planned capacity being unavailable under all warming scenarios. Hotspots of the most water-limited PCPPs are in Pakistan, northwestern India, northwestern and north-central China, and northern Vietnam, where most of the PCPPs will face 30% to 90% unavailable nameplate capacity on annual average. Since coal power plants cannot operate effectively when the capacity factor falls below a minimum load level (about 20% to 50%), the actual limitation on generation capacity would be larger. In general, the PCPPs that will have the highest limitation on annual average capacity will also have the most frequent and longest periods of interrupted operation. These results suggest that to ensure security of energy supply and avoid over-withdrawing water resources, the water-limited PCPPs should implement adaptation measures such as dry-cooling, combined heat- and power, or using recycled wastewater.

Geometrical analysis on cap-shaped coils for power optimization of the vibration-based electromagnetic harvesting system

NASA Astrophysics Data System (ADS)

Hasbullah Mohd Isa, Wan; Fikri Muhammad, Khairul; Mohd Khairuddin, Ismail; Ishak, Ismayuzri; Razlan Yusoff, Ahmad

2016-02-01

This paper presents the new form of coils for electromagnetic energy harvesting system based on topology optimization method which look-liked a cap to maximize the power output. It could increase the number of magnetic flux linkage interception of a cylindrical permanent magnet which in this case is of 10mm diameter. Several coils with different geometrical properties have been build and tested on a vibration generator with frequency of 100Hz. The results showed that the coil with lowest number of winding transduced highest power output of 680μW while the highest number of windings generated highest voltage output of 0.16V.

High efficiency pump combiner fabricated by CO2 laser splicing system

NASA Astrophysics Data System (ADS)

Zhu, Gongwen

2018-02-01

High power combiners are of great interest for high power fiber lasers and fiber amplifiers. With the advent of CO2 laser splicing system, power combiners are made possible with low manufacturing cost, low loss, high reliability and high performance. Traditionally fiber optical components are fabricated with flame torch, electrode arc discharge or filament heater. However, these methods can easily leave contamination on the fiber, resulting inconsistent performance or even catching fire in high power operations. The electrodes or filaments also degrade rapidly during the combiner manufacturing process. The rapid degradation will lead to extensive maintenance, making it unpractical or uneconomic for volume production. By contrast, CO2 laser is the cleanest heating source which provides reliable and repeatable process for fabricating fiber optic components including high power combiners. In this paper we present an all fiber end pumped 7x1 pump combiner fabricated by CO2 laser splicing system. The input pump fibers are 105/125 (core/clad diameters in μm) fibers with a core NA of 0.22. The output fiber is a 300/320 fiber with a core NA of 0.22. The average efficiency is 99.4% with all 7 ports more than 99%. The process is contamination-free and highly repeatable. To our best knowledge, this is the first report in the literature on power combiners fabricated by CO2 laser splicing system. It also has the highest reported efficiency of its kind.

Phase-stable, multi-µJ femtosecond pulses from a repetition-rate tunable Ti:Sa-oscillator-seeded Yb-fiber amplifier

NASA Astrophysics Data System (ADS)

Saule, T.; Holzberger, S.; De Vries, O.; Plötner, M.; Limpert, J.; Tünnermann, A.; Pupeza, I.

2017-01-01

We present a high-power, MHz-repetition-rate, phase-stable femtosecond laser system based on a phase-stabilized Ti:Sa oscillator and a multi-stage Yb-fiber chirped-pulse power amplifier. A 10-nm band around 1030 nm is split from the 7-fs oscillator output and serves as the seed for subsequent amplification by 54 dB to 80 W of average power. The µJ-level output is spectrally broadened in a solid-core fiber and compressed to 30 fs with chirped mirrors. A pulse picker prior to power amplification allows for decreasing the repetition rate from 74 MHz by a factor of up to 4 without affecting the pulse parameters. To compensate for phase jitter added by the amplifier to the feed-forward phase-stabilized seeding pulses, a self-referencing feed-back loop is implemented at the system output. An integrated out-of-loop phase noise of less than 100 mrad was measured in the band from 0.4 Hz to 400 kHz, which to the best of our knowledge corresponds to the highest phase stability ever demonstrated for high-power, multi-MHz-repetition-rate ultrafast lasers. This system will enable experiments in attosecond physics at unprecedented repetition rates, it offers ideal prerequisites for the generation and field-resolved electro-optical sampling of high-power, broadband infrared pulses, and it is suitable for phase-stable white light generation.

Probability density functions of power-in-bucket and power-in-fiber for an infrared laser beam propagating in the maritime environment.

PubMed

Nelson, Charles; Avramov-Zamurovic, Svetlana; Korotkova, Olga; Malek-Madani, Reza; Sova, Raymond; Davidson, Frederic

2013-11-01

Irradiance fluctuations of an infrared laser beam from a shore-to-ship data link ranging from 5.1 to 17.8 km are compared to lognormal (LN), gamma-gamma (GG) with aperture averaging, and gamma-Laguerre (GL) distributions. From our data analysis, the LN and GG probability density function (PDF) models were generally in good agreement in near-weak to moderate fluctuations. This was also true in moderate to strong fluctuations when the spatial coherence radius was smaller than the detector aperture size, with the exception of the 2.54 cm power-in-bucket (PIB) where the LN PDF model fit best. For moderate to strong fluctuations, the GG PDF model tended to outperform the LN PDF model when the spatial coherence radius was greater than the detector aperture size. Additionally, the GL PDF model had the best or next to best overall fit in all cases with the exception of the 2.54 cm PIB where the scintillation index was highest. The GL PDF model also appears to be robust for off-of-beam center laser beam applications.

Properties of nanostructured undoped ZrO{sub 2} thin film electrolytes by plasma enhanced atomic layer deposition for thin film solid oxide fuel cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cho, Gu Young; Noh, Seungtak; Lee, Yoon Ho

2016-01-15

Nanostructured ZrO{sub 2} thin films were prepared by thermal atomic layer deposition (ALD) and by plasma-enhanced atomic layer deposition (PEALD). The effects of the deposition conditions of temperature, reactant, plasma power, and duration upon the physical and chemical properties of ZrO{sub 2} films were investigated. The ZrO{sub 2} films by PEALD were polycrystalline and had low contamination, rough surfaces, and relatively large grains. Increasing the plasma power and duration led to a clear polycrystalline structure with relatively large grains due to the additional energy imparted by the plasma. After characterization, the films were incorporated as electrolytes in thin film solidmore » oxide fuel cells, and the performance was measured at 500 °C. Despite similar structure and cathode morphology of the cells studied, the thin film solid oxide fuel cell with the ZrO{sub 2} thin film electrolyte by the thermal ALD at 250 °C exhibited the highest power density (38 mW/cm{sup 2}) because of the lowest average grain size at cathode/electrolyte interface.« less

Effect of ultrasound on oil recovery from crude oil containing sludge.

PubMed

He, Shilong; Tan, Xicheng; Hu, Xin; Gao, Yingxin

2018-01-16

To recover oil from crude oil containing sludge is still a research hot topic from the view of sustainability, in which ultrasonic has been proven to be an efficient and environment friendly technique. However, the effect of sludge characteristic on ultrasonic-assisted oil recovery efficiency is little known. In this study, the analysis of variance (ANOVA) was conducted based on six types of crude oily sludge with hydrophilicity and lipophilicity separately and five different ultrasonic operation factors (ultrasonic power (A), frequency (B), time (C), initial temperature (D) and pH (E)). The results showed that the oil recovery efficiency was mainly affected by the ultrasonic power and hydrophilicity of sludge (the highest 92% of oil recovery rate was achieved with the ultrasonic power of 240 W and hydrophilic sludge). Moreover, the wettability, decreased average particle size and increased specific surface area of sludge were found after ultrasonic treatment. Besides, changes in the oil component, such as the decrease of asphaltenes along with an increase of saturates, were also further observed. Therefore, the findings in this study can provide technical support for the practical application of ultrasonic technology in different kinds of oily sludge treatment.

152 W average power Tm-doped fiber CPA system.

PubMed

Stutzki, Fabian; Gaida, Christian; Gebhardt, Martin; Jansen, Florian; Wienke, Andreas; Zeitner, Uwe; Fuchs, Frank; Jauregui, Cesar; Wandt, Dieter; Kracht, Dietmar; Limpert, Jens; Tünnermann, Andreas

2014-08-15

A high-power thulium (Tm)-doped fiber chirped-pulse amplification system emitting a record compressed average output power of 152 W and 4 MW peak power is demonstrated. This result is enabled by utilizing Tm-doped photonic crystal fibers with mode-field diameters of 35 μm, which mitigate detrimental nonlinearities, exhibit slope efficiencies of more than 50%, and allow for reaching a pump-power-limited average output power of 241 W. The high-compression efficiency has been achieved by using multilayer dielectric gratings with diffraction efficiencies higher than 98%.

Analysis and design of high-power and efficient, millimeter-wave power amplifier systems using zero degree combiners

NASA Astrophysics Data System (ADS)

Tai, Wei; Abbasi, Mortez; Ricketts, David S.

2018-01-01

We present the analysis and design of high-power millimetre-wave power amplifier (PA) systems using zero-degree combiners (ZDCs). The methodology presented optimises the PA device sizing and the number of combined unit PAs based on device load pull simulations, driver power consumption analysis and loss analysis of the ZDC. Our analysis shows that an optimal number of N-way combined unit PAs leads to the highest power-added efficiency (PAE) for a given output power. To illustrate our design methodology, we designed a 1-W PA system at 45 GHz using a 45 nm silicon-on-insulator process and showed that an 8-way combined PA has the highest PAE that yields simulated output power of 30.6 dBm and 31% peak PAE.

Standard-Cell, Open-Architecture Power Conversion Systems

DTIC Science & Technology

2005-10-01

TLmax Maximum junction temperature 423 OK Table 5. 9. PEBB average model description in VTB. Terminal Type Name - 4 -, A Power DC Bus + B Power AC Pole...5 A. Switching models ........................................................................................ 5 B. Average ...11-6 IV. Average Modeling of PEBB-Based Converters...................................................... 11-10 0 IV. 1.Voltage

High-Average Power Broadband 18-Beam Klystron Circuit and Collector Designs

DTIC Science & Technology

2008-04-01

high -average power S - band multiple-beam klystron are presented. The klystron will be powered by the recently completed 41.6 A, 42...al., “ High - power Four-cavity S - band multiple-beam klystron design,” IEEE Trans. Plasma Science, vol. 33, pp. 1119-1135, April 2005. [3] D.K Abe, et...APR 2008 2. REPORT TYPE 3. DATES COVERED 00-00-2008 to 00-00-2008 4. TITLE AND SUBTITLE High -average Power Broadband 18-beam

Time Averaged Transmitter Power and Exposure to Electromagnetic Fields from Mobile Phone Base Stations

PubMed Central

Bürgi, Alfred; Scanferla, Damiano; Lehmann, Hugo

2014-01-01

Models for exposure assessment of high frequency electromagnetic fields from mobile phone base stations need the technical data of the base stations as input. One of these parameters, the Equivalent Radiated Power (ERP), is a time-varying quantity, depending on communication traffic. In order to determine temporal averages of the exposure, corresponding averages of the ERP have to be available. These can be determined as duty factors, the ratios of the time-averaged power to the maximum output power according to the transmitter setting. We determine duty factors for UMTS from the data of 37 base stations in the Swisscom network. The UMTS base stations sample contains sites from different regions of Switzerland and also different site types (rural/suburban/urban/hotspot). Averaged over all regions and site types, a UMTS duty factor F ≈ 0.32 ± 0.08 for the 24 h-average is obtained, i.e., the average output power corresponds to about a third of the maximum power. We also give duty factors for GSM based on simple approximations and a lower limit for LTE estimated from the base load on the signalling channels. PMID:25105551

Single frequency 1560nm Er:Yb fiber amplifier with 207W output power and 50.5% slope efficiency

NASA Astrophysics Data System (ADS)

Creeden, Daniel; Pretorius, Herman; Limongelli, Julia; Setzler, Scott D.

2016-03-01

High power fiber lasers/amplifiers in the 1550nm spectral region have not scaled as rapidly as Yb-, Tm-, or Ho-doped fibers. This is primarily due to the low gain of the erbium ion. To overcome the low pump absorption, Yb is typically added as a sensitizer. Although this helps the pump absorption, it also creates a problem with parasitic lasing of the Yb ions under strong pumping conditions, which generally limits output power. Other pump schemes have shown high efficiency through resonant pumping of erbium only without the need for Yb as a sensitizer [1-2]. Although this can enable higher power scaling due to a decrease in the thermal loading, resonant pumping methods require long fiber lengths due to pump bleaching, which may limit the power scaling which can be achieved for single frequency output. By using an Er:Yb fiber and pumping in the minima of the Yb pump absorption at 940nm, we have been able to simultaneously generate high power, single frequency output at 1560nm while suppressing the 1-micron ASE and enabling higher efficiency compared to pumping at the absorption peak at 976nm. We have demonstrated single frequency amplification (540Hz linewidth) to 207W average output power with 49.3% optical efficiency (50.5% slope efficiency) in an LMA Er:Yb fiber. We believe this is the highest reported efficiency from a high power 9XXnm pumped Er:Yb-doped fiber amplifier. This is significantly more efficient that the best-reported efficiency for high power Er:Yb doped fibers, which, to-date, has been limited to ~41% slope efficiency [3].

Approximating lens power.

PubMed

Kaye, Stephen B

2009-04-01

To provide a scalar measure of refractive error, based on geometric lens power through principal, orthogonal and oblique meridians, that is not limited to the paraxial and sag height approximations. A function is derived to model sections through the principal meridian of a lens, followed by rotation of the section through orthogonal and oblique meridians. Average focal length is determined using the definition for the average of a function. Average univariate power in the principal meridian (including spherical aberration), can be computed from the average of a function over the angle of incidence as determined by the parameters of the given lens, or adequately computed from an integrated series function. Average power through orthogonal and oblique meridians, can be similarly determined using the derived formulae. The widely used computation for measuring refractive error, the spherical equivalent, introduces non-constant approximations, leading to a systematic bias. The equations proposed provide a good univariate representation of average lens power and are not subject to a systematic bias. They are particularly useful for the analysis of aggregate data, correlating with biological treatment variables and for developing analyses, which require a scalar equivalent representation of refractive power.

Focus on Teacher Salaries: An Update on Average Salaries and Recent Legislative Actions in the SREB States.

ERIC Educational Resources Information Center

Gaines, Gale F.

Focused state efforts have helped teacher salaries in Southern Regional Education Board (SREB) states move toward the national average. Preliminary 2000-01 estimates put SREB's average teacher salary at its highest point in 22 years compared to the national average. The SREB average teacher salary is approximately 90 percent of the national…

Estimation of average annual streamflows and power potentials for Alaska and Hawaii

DOE Office of Scientific and Technical Information (OSTI.GOV)

Verdin, Kristine L.

2004-05-01

This paper describes the work done to develop average annual streamflow estimates and power potential for the states of Alaska and Hawaii. The Elevation Derivatives for National Applications (EDNA) database was used, along with climatic datasets, to develop flow and power estimates for every stream reach in the EDNA database. Estimates of average annual streamflows were derived using state-specific regression equations, which were functions of average annual precipitation, precipitation intensity, drainage area, and other elevation-derived parameters. Power potential was calculated through the use of the average annual streamflow and the hydraulic head of each reach, which is calculated from themore » EDNA digital elevation model. In all, estimates of streamflow and power potential were calculated for over 170,000 stream segments in the Alaskan and Hawaiian datasets.« less

Efficient determination of vehicle emission factors by fuel use category using on-road measurements: downward trends on Los Angeles freight corridor I-710

PubMed Central

Hudda, N.; Fruin, S.; Delfino, R. J.; Sioutas, C.

2013-01-01

To evaluate the success of vehicle emissions regulations, trends in both fleet-wide average emissions as well as high-emitter emissions are needed, but it is challenging to capture the full spread of vehicle emission factors (EFs) with chassis dynamometer or tunnel studies, and remote sensing studies cannot evaluate particulate compounds. We developed an alternative method that links real-time on-road pollutant measurements from a mobile platform with real-time traffic data, and allows efficient calculation of both the average and the spread of EFs for light-duty gasoline-powered vehicles (LDG) and heavy-duty diesel-powered vehicles (HDD). This is the first study in California to report EFs under a full range of real-world driving conditions on multiple freeways. Fleet average LDG EFs were in agreement with most recent studies and an order of magnitude lower than observed HDD EFs. HDD EFs reflected the relatively rapid decreases in diesel emissions that have recently occurred in Los Angeles/California, and on I-710, a primary route used for goods movement and a focus of additional truck fleet turnover incentives, HDD EFs were often lower than on other freeways. When freeway emission rates (ER) were quantified as the product of EF and vehicle miles traveled (VMT) per time per mile of freeway, despite a twoto three-fold difference in HDD fractions between freeways, ERs were found to be generally similar in magnitude. Higher LDG VMT on low HDD fraction freeways largely offset the difference. Therefore, the conventional assumption that free ways with the highest HDD fractions are significantly worse sources of total emissions in Los Angeles may no longer be true. PMID:24244208

Efficient determination of vehicle emission factors by fuel use category using on-road measurements: downward trends on Los Angeles freight corridor I-710.

PubMed

Hudda, N; Fruin, S; Delfino, R J; Sioutas, C

2013-01-11

To evaluate the success of vehicle emissions regulations, trends in both fleet-wide average emissions as well as high-emitter emissions are needed, but it is challenging to capture the full spread of vehicle emission factors (EFs) with chassis dynamometer or tunnel studies, and remote sensing studies cannot evaluate particulate compounds. We developed an alternative method that links real-time on-road pollutant measurements from a mobile platform with real-time traffic data, and allows efficient calculation of both the average and the spread of EFs for light-duty gasoline-powered vehicles (LDG) and heavy-duty diesel-powered vehicles (HDD). This is the first study in California to report EFs under a full range of real-world driving conditions on multiple freeways. Fleet average LDG EFs were in agreement with most recent studies and an order of magnitude lower than observed HDD EFs. HDD EFs reflected the relatively rapid decreases in diesel emissions that have recently occurred in Los Angeles/California, and on I-710, a primary route used for goods movement and a focus of additional truck fleet turnover incentives, HDD EFs were often lower than on other freeways. When freeway emission rates (ER) were quantified as the product of EF and vehicle miles traveled (VMT) per time per mile of freeway, despite a twoto three-fold difference in HDD fractions between freeways, ERs were found to be generally similar in magnitude. Higher LDG VMT on low HDD fraction freeways largely offset the difference. Therefore, the conventional assumption that free ways with the highest HDD fractions are significantly worse sources of total emissions in Los Angeles may no longer be true.

Real-world energy use and emission rates for idling long-haul trucks and selected idle reduction technologies.

PubMed

Frey, H Christopher; Kuo, Po-Yao

2009-07-01

Long-haul freight trucks typically idle for 2000 or more hours per year, motivating interest in reducing idle fuel use and emissions using auxiliary power units (APUs) and shore-power (SP). Fuel-use rates are estimated based on electronic control unit (ECU) data for truck engines and measurements for APU engines. Engine emission factors were measured using a portable emission measurement system. Indirect emissions from SP were based on average utility grid emission factors. Base engine fuel use and APU and SP electrical load were analyzed for 20 trucks monitored for more than 1 yr during 2.76 million mi of activity within 42 U.S. states. The average base engine fuel use varied from 0.46 to 0.65 gal/hr. The average APU fuel use varied from 0.24 to 0.41 gal/hr. Fuel-use rates are typically lowest in mild weather, highest in hot or cold weather, and depend on engine speed (revolutions per minute [RPM]). Compared with the base engine, APU fuel use and emissions of carbon dioxide (CO2) and sulfur dioxide (SO2) are lower by 36-47%. Oxides of nitrogen (NO(x)) emissions are lower by 80-90%. Reductions in particulate matter (PM), carbon monoxide (CO), and hydrocarbon emissions vary from approximately 10 to over 50%. SP leads to more substantial reductions, except for SO2. The actual achievable reductions will be lower because only a fraction of base engine usage will be replaced by APUs, SP, or both. Recommendations are made for reducing base engine fuel use and emissions, accounting for variability in fuel use and emissions reductions, and further work to quantify real-world avoided fuel use and emissions.

Optimal Padding for the Two-Dimensional Fast Fourier Transform

NASA Technical Reports Server (NTRS)

Dean, Bruce H.; Aronstein, David L.; Smith, Jeffrey S.

2011-01-01

One-dimensional Fast Fourier Transform (FFT) operations work fastest on grids whose size is divisible by a power of two. Because of this, padding grids (that are not already sized to a power of two) so that their size is the next highest power of two can speed up operations. While this works well for one-dimensional grids, it does not work well for two-dimensional grids. For a two-dimensional grid, there are certain pad sizes that work better than others. Therefore, the need exists to generalize a strategy for determining optimal pad sizes. There are three steps in the FFT algorithm. The first is to perform a one-dimensional transform on each row in the grid. The second step is to transpose the resulting matrix. The third step is to perform a one-dimensional transform on each row in the resulting grid. Steps one and three both benefit from padding the row to the next highest power of two, but the second step needs a novel approach. An algorithm was developed that struck a balance between optimizing the grid pad size with prime factors that are small (which are optimal for one-dimensional operations), and with prime factors that are large (which are optimal for two-dimensional operations). This algorithm optimizes based on average run times, and is not fine-tuned for any specific application. It increases the amount of times that processor-requested data is found in the set-associative processor cache. Cache retrievals are 4-10 times faster than conventional memory retrievals. The tested implementation of the algorithm resulted in faster execution times on all platforms tested, but with varying sized grids. This is because various computer architectures process commands differently. The test grid was 512 512. Using a 540 540 grid on a Pentium V processor, the code ran 30 percent faster. On a PowerPC, a 256x256 grid worked best. A Core2Duo computer preferred either a 1040x1040 (15 percent faster) or a 1008x1008 (30 percent faster) grid. There are many industries that can benefit from this algorithm, including optics, image-processing, signal-processing, and engineering applications.

Analytical expressions for maximum wind turbine average power in a Rayleigh wind regime

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carlin, P.W.

Average or expectation values for annual power of a wind turbine in a Rayleigh wind regime are calculated and plotted as a function of cut-out wind speed. This wind speed is expressed in multiples of the annual average wind speed at the turbine installation site. To provide a common basis for comparison of all real and imagined turbines, the Rayleigh-Betz wind machine is postulated. This machine is an ideal wind machine operating with the ideal Betz power coefficient of 0.593 in a Rayleigh probability wind regime. All other average annual powers are expressed in fractions of that power. Cases consideredmore » include: (1) an ideal machine with finite power and finite cutout speed, (2) real machines operating in variable speed mode at their maximum power coefficient, and (3) real machines operating at constant speed.« less

Green Power Markets

EPA Pesticide Factsheets

The U.S. EPA's Green Power Partnership defines Green power is a subset of renewable energy and represents those renewable energy resources and technologies that provide the highest environmental benefit.

Disabling and fatal occupational claim rates, risks, and costs in the Oregon construction industry 1990-1997.

PubMed

Horwitz, Irwin B; McCall, Brian P

2004-10-01

This study estimated injury and illness rates, risk factors, and costs associated with construction work in Oregon from 1990-1997 using all accepted workers' compensation claims by Oregon construction employees (N = 20,680). Claim rates and risk estimates were estimated using a baseline calculated from Current Population Survey data of the Oregon workforce. The average annual rate of lost-time claims was 3.5 per 100 workers. More than 50% of claims were by workers under 35 years and with less than 1 year of tenure. The majority of claimants (96.1%) were male. There were 52 total fatalities reported over the period examined, representing an average annual death rate of 8.5 per 100,000 construction workers. Average claim cost was $10,084 and mean indemnity time was 57.3 days. Structural metal workers had the highest average days of indemnity of all workers (72. 1), highest average costs per claim ($16,472), and highest odds ratio of injury of all occupations examined. Sprains were the most frequently reported injury type, constituting 46.4% of all claims. The greatest accident risk occurred during the third hour of work. Training interventions should be extensively utilized for inexperienced workers, and prework exercises could potentially reduce injury frequency and severity.

Splash dispersal of Phyllosticta citricarpa conidia from infected citrus fruit

PubMed Central

Perryman, S. A. M.; Clark, S. J.; West, J. S.

2014-01-01

Rain-splash dispersal of Phyllosticta citricarpa (syn. Guignardia citricarpa) conidia (pycnidiospores) from infected oranges was studied in still air and combined with wind. High power microscopy demonstrated the presence of conidia in splash droplets from diseased oranges, which exuded conidia for over one hour during repeated wetting. The largest (5 mm) incident drops produced the highest splashes (up to 41.0 cm). A linear-by-quadratic surface model predicted highest splashes to be 41.91 cm at a horizontal distance of 25.97 cm from the target orange. Large splash droplets contained most conidia (4–5.5 mm splashes averaged 308 conidia), but were splashed <30 cm horizontal distance. Most (80–90%) splashes were <1 mm diameter but carried only 0–4 conidia per droplet. In multiple splash experiments, splashes combined to reach higher maxima (up to 61.7 cm; linear-by-quadratic surface model prediction, 62.1 cm) than in the single splash experiments. In combination with wind, higher wind speeds carried an increasing proportion of splashes downwind travelling horizontally at least 8 m at the highest wind speed tested (7 m/s), due to a small proportion of droplets (<1 mm) being aerosolised. These experiments suggest that P. citricarpa conidia can be dispersed from infected oranges by splashes of water in rainfall events. PMID:25298272

Splash dispersal of Phyllosticta citricarpa conidia from infected citrus fruit.

PubMed

Perryman, S A M; Clark, S J; West, J S

2014-10-09

Rain-splash dispersal of Phyllosticta citricarpa (syn. Guignardia citricarpa) conidia (pycnidiospores) from infected oranges was studied in still air and combined with wind. High power microscopy demonstrated the presence of conidia in splash droplets from diseased oranges, which exuded conidia for over one hour during repeated wetting. The largest (5 mm) incident drops produced the highest splashes (up to 41.0 cm). A linear-by-quadratic surface model predicted highest splashes to be 41.91 cm at a horizontal distance of 25.97 cm from the target orange. Large splash droplets contained most conidia (4-5.5 mm splashes averaged 308 conidia), but were splashed <30 cm horizontal distance. Most (80-90%) splashes were <1 mm diameter but carried only 0-4 conidia per droplet. In multiple splash experiments, splashes combined to reach higher maxima (up to 61.7 cm; linear-by-quadratic surface model prediction, 62.1 cm) than in the single splash experiments. In combination with wind, higher wind speeds carried an increasing proportion of splashes downwind travelling horizontally at least 8 m at the highest wind speed tested (7 m/s), due to a small proportion of droplets (<1 mm) being aerosolised. These experiments suggest that P. citricarpa conidia can be dispersed from infected oranges by splashes of water in rainfall events.

40 CFR 60.145a - Compliance provisions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... data sets shall be determined accordingly. (e) To determine compliance with § 60.142a(a)(1), select the data sets yielding the highest and second highest 3-minute average opacities for each steel production...

40 CFR 60.145a - Compliance provisions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... data sets shall be determined accordingly. (e) To determine compliance with § 60.142a(a)(1), select the data sets yielding the highest and second highest 3-minute average opacities for each steel production...

40 CFR 60.145a - Compliance provisions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... data sets shall be determined accordingly. (e) To determine compliance with § 60.142a(a)(1), select the data sets yielding the highest and second highest 3-minute average opacities for each steel production...

40 CFR 60.145a - Compliance provisions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... data sets shall be determined accordingly. (e) To determine compliance with § 60.142a(a)(1), select the data sets yielding the highest and second highest 3-minute average opacities for each steel production...

40 CFR 60.145a - Compliance provisions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... data sets shall be determined accordingly. (e) To determine compliance with § 60.142a(a)(1), select the data sets yielding the highest and second highest 3-minute average opacities for each steel production...

Ambient air metallic pollutant study at HAF areas during 2013-2014

NASA Astrophysics Data System (ADS)

Fang, Guor-Cheng; Kuo, Yu-Chen; Zhuang, Yuan-Jie

2015-05-01

This study characterized diurnal variations of the total suspended particulate (TSP) concentrations, dry deposition flux and dry deposition velocity of metallic elements at Taichung Harbor (Harbor), Gong Ming Junior High School (Airport) and Sha lu Farmland (Farmland) sampling sites in central Taiwan between August, 2013 and July, 2014 in this study. The result indicated that: 1) the ambient air particulate concentrations, dry depositions were displayed as Harbor > Farmland > Airport during the day time sampling period. However, dry deposition velocities were shown as Airport > Harbor > Farmland for this study. 2) The ambient air particulate concentrations, dry depositions were displayed as Airport > Harbor > Farmland during the night time sampling period. However, dry deposition velocities were shown as Farmland > Harbor > Airport for this study. 3) The metallic element Zn has the average highest concentrations at Airport, Harbor and Farmland among all the metallic elements during the day time sampling period in this study. 4) There were significant differences for the metallic elements (Cr, Cu, Zn and Pb) in dry depositions at these three characteristic sampling sites (HAF) for the night time sampling period. The only exception is metallic element Cd. It displayed that there were no significant differences for the metallic element Cd at the Airport and Farmland sampling sites during the night time sampling period. 5) The average highest values for the metallic element Cu in TSP among the three characteristic sampling sites occurred during the fall and winter seasons for this study. As for the dry depositions, the average highest values in dry deposition among the three characteristic sampling sites occurred during the spring and summer seasons for this study. 6) The average highest values for the metallic element Cd in TSP among the three characteristic sampling sites occurred during the spring and summer seasons for this study. As for the dry depositions, the average highest values in dry deposition among the three characteristic sampling sites occurred during fall and winter for this study.

What Is Green Power?

EPA Pesticide Factsheets

The U.S. EPA's Green Power Partnership defines Green power is a subset of renewable energy and represents those renewable energy resources and technologies that provide the highest environmental benefit.

National-level infrastructure and economic effects of switchgrass cofiring with coal in existing power plants for carbon mitigation.

PubMed

Morrow, William R; Griffin, W Michael; Matthews, H Scott

2008-05-15

We update a previously presented Linear Programming (LP) methodology for estimating state level costs for reducing CO2 emissions from existing coal-fired power plants by cofiring switchgrass, a biomass energy crop, and coal. This paper presents national level results of applying the methodology to the entire portion of the United States in which switchgrass could be grown without irrigation. We present incremental switchgrass and coal cofiring carbon cost of mitigation curves along with a presentation of regionally specific cofiring economics and policy issues. The results show that cofiring 189 million dry short tons of switchgrass with coal in the existing U.S. coal-fired electricity generation fleet can mitigate approximately 256 million short tons of carbon-dioxide (CO2) per year, representing a 9% reduction of 2005 electricity sector CO2 emissions. Total marginal costs, including capital, labor, feedstock, and transportation, range from $20 to $86/ton CO2 mitigated,with average costs ranging from $20 to $45/ton. If some existing power plants upgrade to boilers designed for combusting switchgrass, an additional 54 million tons of switchgrass can be cofired. In this case, total marginal costs range from $26 to $100/ton CO2 mitigated, with average costs ranging from $20 to $60/ton. Costs for states east of the Mississippi River are largely unaffected by boiler replacement; Atlantic seaboard states represent the lowest cofiring cost of carbon mitigation. The central plains states west of the Mississippi River are most affected by the boiler replacement option and, in general, go from one of the lowest cofiring cost of carbon mitigation regions to the highest. We explain the variation in transportation expenses and highlight regional cost of mitigation variations as transportation overwhelms other cofiring costs.

Measurements and predictors of on-road ultrafine particle concentrations and associated pollutants in Los Angeles

NASA Astrophysics Data System (ADS)

Fruin, S.; Westerdahl, D.; Sax, T.; Sioutas, C.; Fine, P. M.

Motor vehicles are the dominant source of oxides of nitrogen (NO x), particulate matter (PM), and certain air toxics (e.g., benzene, 1,3-butadiene) in urban areas. On roadways, motor vehicle-related pollutant concentrations are typically many times higher than ambient concentrations. Due to high air exchange rates typical of moving vehicles, this makes time spent in vehicles on roadways a major source of exposure. This paper presents on-road measurements for Los Angeles freeways and arterial roads taken from a zero-emission electric vehicle outfitted with real-time instruments. The objective was to characterize air pollutant concentrations on roadways and identify the factors associated with the highest concentrations. Our analysis demonstrated that on freeways, concentrations of ultrafine particles (UFPs), black carbon, nitric oxide, and PM-bound polycyclic aromatic hydrocarbons (PM-PAH) are generated primarily by diesel-powered vehicles, despite the relatively low fraction (˜6%) of diesel-powered vehicles on Los Angeles freeways. However, UFP concentrations on arterial roads appeared to be driven primarily by proximity to gasoline-powered vehicles undergoing hard accelerations. Concentrations were roughly one-third of those on freeways. By using a multiple regression model for the freeway measurements, we were able to explain 60-70% of the variability in concentrations of UFP, black carbon, nitric oxide, and PM-PAH using measures of diesel truck density and hour of day (as an indicator of wind speed). Freeway concentrations of these pollutants were also well correlated with readily available annual average daily truck counts, potentially allowing improved population exposure estimates for epidemiology studies. Based on these roadway measurements and average driving time, it appears that 33-45% of total UFP exposure for Los Angeles residents occurs due to time spent traveling in vehicles.

Integrated unaligned resonant modulator tuning

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zortman, William A.; Lentine, Anthony L.

Methods and systems for tuning a resonant modulator are disclosed. One method includes receiving a carrier signal modulated by the resonant modulator with a stream of data having an approximately equal number of high and low bits, determining an average power of the modulated carrier signal, comparing the average power to a predetermined threshold, and operating a tuning device coupled to the resonant modulator based on the comparison of the average power and the predetermined threshold. One system includes an input structure, a plurality of processing elements, and a digital control element. The input structure is configured to receive, frommore » the resonant modulator, a modulated carrier signal. The plurality of processing elements are configured to determine an average power of the modulated carrier signal. The digital control element is configured to operate a tuning device coupled to the resonant modulator based on the average power of the modulated carrier signal.« less

Module failure isolation circuit for paralleled inverters. [preventing system failure during power conditioning for spacecraft applications

NASA Technical Reports Server (NTRS)

Nagano, S. (Inventor)

1979-01-01

A module failure isolation circuit is described which senses and averages the collector current of each paralled inverter power transistor and compares the collector current of each power transistor the average collector current of all power transistors to determine when the sensed collector current of a power transistor in any one inverter falls below a predetermined ratio of the average collector current. The module associated with any transistor that fails to maintain a current level above the predetermined radio of the average collector current is then shut off. A separate circuit detects when there is no load, or a light load, to inhibit operation of the isolation circuit during no load or light load conditions.

Analytical Assessment of the Relationship between 100MWp Large-scale Grid-connected Photovoltaic Plant Performance and Meteorological Parameters

NASA Astrophysics Data System (ADS)

Sheng, Jie; Zhu, Qiaoming; Cao, Shijie; You, Yang

2017-05-01

This paper helps in study of the relationship between the photovoltaic power generation of large scale “fishing and PV complementary” grid-tied photovoltaic system and meteorological parameters, with multi-time scale power data from the photovoltaic power station and meteorological data over the same period of a whole year. The result indicates that, the PV power generation has the most significant correlation with global solar irradiation, followed by diurnal temperature range, sunshine hours, daily maximum temperature and daily average temperature. In different months, the maximum monthly average power generation appears in August, which related to the more global solar irradiation and longer sunshine hours in this month. However, the maximum daily average power generation appears in October, this is due to the drop in temperature brings about the improvement of the efficiency of PV panels. Through the contrast of monthly average performance ratio (PR) and monthly average temperature, it is shown that, the larger values of monthly average PR appears in April and October, while it is smaller in summer with higher temperature. The results concluded that temperature has a great influence on the performance ratio of large scale grid-tied PV power system, and it is important to adopt effective measures to decrease the temperature of PV plant properly.

Longer Hospice Stays Associated With Decreased End-Of-Life Spending For Patients In Regions With High Expenditures

PubMed Central

Wang, Shi-Yi; Hsu, Sylvia H.; Huang, Siwan; Soulos, Pamela R.; Gross, Cary P.

2018-01-01

Hospice is expected to decrease end-of-life care expenditures yet evidence for its financial impact remains inconclusive. One potential explanation is that hospice enrollment may produce differential cost saving effects by region, due to geographic variation in end-of-life care spending patterns. Accordingly, we examined 103,745 elderly Medicare fee-for-service beneficiaries in the Surveillance, Epidemiology, and End Results-Medicare database who died from cancer in 2004–2011. We created quintiles by the mean end-of-life expenditure per hospital referral region (HRR), and examined HRR-level variation in the associations between length of hospice enrollment and expenditures among quintiles. Results showed that longer hospice stays were associated with decreased end-of-life expenditures for patients residing in regions of high average expenditures, but not for those in regions with low average expenditures. Hospice use accounted for 8.0% of the expenditure variation between the highest and lowest quintile areas, demonstrating the powers and limitations of hospice use for cost saving. PMID:28167723

QCL as a game changer in MWIR and LWIR military and homeland security applications

NASA Astrophysics Data System (ADS)

Patel, C. Kumar N.; Lyakh, Arkadiy; Maulini, Richard; Tsekoun, Alexei; Tadjikov, Boris

2012-06-01

QCLs represent an important advance in MWIR and LWIR laser technology. With the demonstration of CW/RT QCLs, large number applications for QCLs have opened up, some of which represent replacement of currently used laser sources such as OPOs and OPSELs, and others being new uses which were not possible using earlier MWIR/LWIR laser sources, namely OPOs, OPSELs and CO2 lasers. Pranalytica has made significant advances in CW/RT power and WPE of QCLs and through its invention of a new QCL structure design, the non-resonant extraction, has demonstrated single emitter power of >4.7 W and WPE of >17% in the 4.4μm-5.0μm region. Pranalytica has also been commercially supplying the highest power MWIR QCLs with high WPEs. The NRE design concept now has been extended to the shorter wavelengths (3.8μm-4.2μm) with multiwatt power outputs and to longer wavelengths (7μm-10μm) with >1 W output powers. The high WPE of the QCLs permits RT operation of QCLs without using TECs in quasi-CW mode where multiwatt average powers are obtained even in ambient T>70°C. The QCW uncooled operation is particularly attractive for handheld, battery-operated applications where electrical power is limited. This paper describes the advances in QCL technology and applications of the high power MWIR and LWIR QCLs for defense applications, including protection of aircraft from MANPADS, standoff detection of IEDs, insitu detection of CWAs and explosives, infrared IFF beacons and target designators. We see that the SWaP advantages of QCLs are game changers.

47 CFR 15.403 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... power control level. Power must be summed across all antennas and antenna elements. The average must not... symbols, during which the average symbol envelope power is constant. (q) RLAN. Radio Local Area Network. (r) Transmit Power Control (TPC). A feature that enables a U-NII device to dynamically switch between...

Identify the ability to purchase a house in the five major cities of Java for the Indonesian middle class using correspondence analysis

NASA Astrophysics Data System (ADS)

Ginanjar, Irlandia; Indratno, Sapto W.

2015-12-01

Ministry of Housing Republic of Indonesia explained that the Constitution mandates that every citizen has the right to reside. Jakarta, Surabaya, Bandung, Semarang, and Yogyakarta are five of Java's major cities with high population and investment opportunities, so the housing needs in that five cities is very high. Market sentiment analysis recorded the average of property purchasing power for Indonesian society around Rp 250 million, which the author assumes that the highest price for Indonesian middle class. Based on the fact, does the Indonesian middle class have the ability to purchase a house in the five major cities of Java? What facilities do they get? Both questions can be answered using the results of correspondence analysis.

Decadal emission estimates of carbon dioxide, sulfur dioxide, and nitric oxide emissions from coal burning in electric power generation plants in India.

PubMed

Mittal, Moti L; Sharma, Chhemendra; Singh, Richa

2014-10-01

This study aims to estimate the emissions of carbon dioxide (CO₂), sulfur dioxide (SO₂), and nitric oxide (NO) for coal combustion in thermal power plants in India using plant-specific emission factors during the period of 2001/02 to 2009/10. The mass emission factors have been theoretically calculated using the basic principles of combustion under representative prevailing operating conditions in the plants and fuel composition. The results show that from 2001/02 to 2009/10 period, total CO₂ emissions have increased from 324 to 499 Mt/year; SO₂ emissions have increased from 2,519 to 3,840 kt/year; and NO emissions have increased from 948 to 1,539 kt/year from the Indian coal-fired power plants. National average emissions per unit of electricity from the power plants do not show a noticeable improvement during this period. Emission efficiencies for new plants that use improved technology are found to be better than those of old plants. As per these estimates, the national average of CO₂ emissions per unit of electricity varies between 0.91 and 0.95 kg/kWh while SO₂ and NO emissions vary in the range of 6.9 to 7.3 and 2.8 to 2.9 g/kWh, respectively. Yamunagar plant in Haryana state showed the highest emission efficiencies with CO₂ emissions as 0.58 kg/kWh, SO₂ emissions as 3.87 g/kWh, and NO emissions as 1.78 g/kWh, while the Faridabad plant has the lowest emission efficiencies with CO₂ emissions as 1.5 kg/kWh, SO₂ emissions as 10.56 g/kWh, and NO emissions as 4.85 g/kWh. Emission values at other plants vary between the values of these two plants.

Mitigation of multipacting, enhanced by gas condensation on the high power input coupler of a superconducting RF module, by comprehensive warm aging

NASA Astrophysics Data System (ADS)

Wang, Chaoen; Chang, Lung-Hai; Chang, Mei-Hsia; Chen, Ling-Jhen; Chung, Fu-Tsai; Lin, Ming-Chyuan; Liu, Zong-Kai; Lo, Chih-Hung; Tsai, Chi-Lin; Yeh, Meng-Shu; Yu, Tsung-Chi

2017-11-01

Excitation of multipacting, enhanced by gas condensation on cold surfaces of the high power input coupler in a SRF module poses the highest challenge for reliable SRF operation under high average RF power. This could prevent the light source SRF module from being operated with a desired high beam current. Off-line long-term reliability tests have been conducted for the newly constructed 500-MHz SRF KEKB type modules at an accelerating RF voltage of 1.6-MV to enable prediction of their operational reliability in the 3-GeV Taiwan Photon Source (TPS), since prediction from mere production performance by conventional horizontal test is presently unreliable. As expected, operational difficulties resulting from multipacting, enhanced by gas condensation, have been identified in the course of long-term reliability test. Our present hypothesis is that gas condensation can be slowed down by preserving the vacuum pressure at the power coupler close to that reached just after its cool down to liquid helium temperatures. This is achievable by reduction of the power coupler out-gassing rate through comprehensive warm aging. Its feasibility and effectiveness has been experimentally verified in a second long term reliability test. Our success opens the possibility to operate the SRF module free of multipacting trouble and opens a new direction to improve the operational performance of next generation SRF modules in light sources with high beam currents.

High-power linearly polarized diode-side-pumped a-cut Nd:GdVO4 rod laser

NASA Astrophysics Data System (ADS)

Li, Xiaowen; Qian, Jianqiang; Zhang, Baitao

2017-03-01

An efficiently high-power diode-side-pumped Nd:GdVO4 rod laser system was successfully demonstrated, operating in continuous wave (CW) and acousto-optically (AO) Q-switched regime. With a 65 mm-long a-cut Nd:GdVO4 crystal, a maximum linearly polarized CW output power of 60 W at 1063.2 nm was obtained under an absorbed pump power of 180 W, corresponding to a slope efficiency of 50.6%. The output laser beam was linearly polarized with a degree of polarization of 98%. In AO Q-switched operation, the highest output power, minimum pulse width, and highest peak power were achieved to be 42 W, 36 ns, and 58 kW at the pulse repetition frequency of 20 kHz.

Spatially and Temporally Resolved Analysis of Environmental Trade-Offs in Electricity Generation.

PubMed

Peer, Rebecca A M; Garrison, Jared B; Timms, Craig P; Sanders, Kelly T

2016-04-19

The US power sector is a leading contributor of emissions that affect air quality and climate. It also requires a lot of water for cooling thermoelectric power plants. Although these impacts affect ecosystems and human health unevenly in space and time, there has been very little quantification of these environmental trade-offs on decision-relevant scales. This work quantifies hourly water consumption, emissions (i.e., carbon dioxide, nitrogen oxides, and sulfur oxides), and marginal heat rates for 252 electricity generating units (EGUs) in the Electric Reliability Council of Texas (ERCOT) region in 2011 using a unit commitment and dispatch model (UC&D). Annual, seasonal, and daily variations, as well as spatial variability are assessed. When normalized over the grid, hourly average emissions and water consumption intensities (i.e., output per MWh) are found to be highest when electricity demand is the lowest, as baseload EGUs tend to be the most water and emissions intensive. Results suggest that a large fraction of emissions and water consumption are caused by a small number of power plants, mainly baseload coal-fired generators. Replacing 8-10 existing power plants with modern natural gas combined cycle units would result in reductions of 19-29%, 51-55%, 60-62%, and 13-27% in CO2 emissions, NOx emissions, SOx emissions, and water consumption, respectively, across the ERCOT region for two different conversion scenarios.

Exploring the meteorological potential for planning a high performance European electricity super-grid: optimal power capacity distribution among countries

NASA Astrophysics Data System (ADS)

Santos-Alamillos, Francisco J.; Brayshaw, David J.; Methven, John; Thomaidis, Nikolaos S.; Ruiz-Arias, José A.; Pozo-Vázquez, David

2017-11-01

The concept of a European super-grid for electricity presents clear advantages for a reliable and affordable renewable power production (photovoltaics and wind). Based on the mean-variance portfolio optimization analysis, we explore optimal scenarios for the allocation of new renewable capacity at national level in order to provide to energy decision-makers guidance about which regions should be mostly targeted to either maximize total production or reduce its day-to-day variability. The results show that the existing distribution of renewable generation capacity across Europe is far from optimal: i.e. a ‘better’ spatial distribution of resources could have been achieved with either a ~31% increase in mean power supply (for the same level of day-to-day variability) or a ~37.5% reduction in day-to-day variability (for the same level of mean productivity). Careful planning of additional increments in renewable capacity at the European level could, however, act to significantly ameliorate this deficiency. The choice of where to deploy resources depends, however, on the objective being pursued—if the goal is to maximize average output, then new capacity is best allocated in the countries with highest resources, whereas investment in additional capacity in a north/south dipole pattern across Europe would act to most reduce daily variations and thus decrease the day-to-day volatility of renewable power supply.

Apertured averaged scintillation of fully and partially coherent Gaussian, annular Gaussian, flat toped and dark hollow beams

NASA Astrophysics Data System (ADS)

Eyyuboğlu, Halil T.

2015-03-01

Apertured averaged scintillation requires the evaluation of rather complicated irradiance covariance function. Here we develop a much simpler numerical method based on our earlier introduced semi-analytic approach. Using this method, we calculate aperture averaged scintillation of fully and partially coherent Gaussian, annular Gaussian flat topped and dark hollow beams. For comparison, the principles of equal source beam power and normalizing the aperture averaged scintillation with respect to received power are applied. Our results indicate that for fully coherent beams, upon adjusting the aperture sizes to capture 10 and 20% of the equal source power, Gaussian beam needs the largest aperture opening, yielding the lowest aperture average scintillation, whilst the opposite occurs for annular Gaussian and dark hollow beams. When assessed on the basis of received power normalized aperture averaged scintillation, fixed propagation distance and aperture size, annular Gaussian and dark hollow beams seem to have the lowest scintillation. Just like the case of point-like scintillation, partially coherent beams will offer less aperture averaged scintillation in comparison to fully coherent beams. But this performance improvement relies on larger aperture openings. Upon normalizing the aperture averaged scintillation with respect to received power, fully coherent beams become more advantageous than partially coherent ones.

High-Power Growth-Robust InGaAs/InAlAs Terahertz Quantum Cascade Lasers

PubMed Central

2017-01-01

We report on high-power terahertz quantum cascade lasers based on low effective electron mass InGaAs/InAlAs semiconductor heterostructures with excellent reproducibility. Growth-related asymmetries in the form of interface roughness and dopant migration play a crucial role in this material system. These bias polarity dependent phenomena are studied using a nominally symmetric active region resulting in a preferential electron transport in the growth direction. A structure based on a three-well optical phonon depletion scheme was optimized for this bias direction. Depending on the sheet doping density, the performance of this structure shows a trade-off between high maximum operating temperature and high output power. While the highest operating temperature of 155 K is observed for a moderate sheet doping density of 2 × 1010 cm–2, the highest peak output power of 151 mW is found for 7.3 × 1010 cm–2. Furthermore, by abutting a hyperhemispherical GaAs lens to a device with the highest doping level a record output power of 587 mW is achieved for double-metal waveguide structures. PMID:28470028

High-Power Growth-Robust InGaAs/InAlAs Terahertz Quantum Cascade Lasers.

PubMed

Deutsch, Christoph; Kainz, Martin Alexander; Krall, Michael; Brandstetter, Martin; Bachmann, Dominic; Schönhuber, Sebastian; Detz, Hermann; Zederbauer, Tobias; MacFarland, Donald; Andrews, Aaron Maxwell; Schrenk, Werner; Beck, Mattias; Ohtani, Keita; Faist, Jérôme; Strasser, Gottfried; Unterrainer, Karl

2017-04-19

We report on high-power terahertz quantum cascade lasers based on low effective electron mass InGaAs/InAlAs semiconductor heterostructures with excellent reproducibility. Growth-related asymmetries in the form of interface roughness and dopant migration play a crucial role in this material system. These bias polarity dependent phenomena are studied using a nominally symmetric active region resulting in a preferential electron transport in the growth direction. A structure based on a three-well optical phonon depletion scheme was optimized for this bias direction. Depending on the sheet doping density, the performance of this structure shows a trade-off between high maximum operating temperature and high output power. While the highest operating temperature of 155 K is observed for a moderate sheet doping density of 2 × 10 10 cm -2 , the highest peak output power of 151 mW is found for 7.3 × 10 10 cm -2 . Furthermore, by abutting a hyperhemispherical GaAs lens to a device with the highest doping level a record output power of 587 mW is achieved for double-metal waveguide structures.

Electron- and photon-impact ionization of furfural

NASA Astrophysics Data System (ADS)

Jones, D. B.; Ali, E.; Nixon, K. L.; Limão-Vieira, P.; Hubin-Franskin, M.-J.; Delwiche, J.; Ning, C. G.; Colgan, J.; Murray, A. J.; Madison, D. H.; Brunger, M. J.

2015-11-01

The He(i) photoelectron spectrum of furfural has been investigated, with its vibrational structure assigned for the first time. The ground and excited ionized states are assigned through ab initio calculations performed at the outer-valence Green's function level. Triple differential cross sections (TDCSs) for electron-impact ionization of the unresolved combination of the 4a″ + 21a' highest and next-highest occupied molecular orbitals have also been obtained. Experimental TDCSs are recorded in a combination of asymmetric coplanar and doubly symmetric coplanar kinematics. The experimental TDCSs are compared to theoretical calculations, obtained within a molecular 3-body distorted wave framework that employed either an orientation average or proper TDCS average. The proper average calculations suggest that they may resolve some of the discrepancies regarding the angular distributions of the TDCS, when compared to calculations employing the orbital average.

Modeling the oxidative capacity of the atmosphere of the south coast air basin of California. 1. Ozone formation metrics.

PubMed

Griffin, Robert J; Revelle, Meghan K; Dabdub, Donald

2004-02-01

Metrics associated with ozone (O3) formation are investigated using the California Institute of Technology (CIT) three-dimensional air-quality model. Variables investigated include the O3 production rate (P(O3)), O3 production efficiency (OPE), and total reactivity (the sum of the reactivity of carbon monoxide (CO) and all organic gases that react with the hydroxyl radical). Calculations are spatially and temporally resolved; surface-level and vertically averaged results are shown for September 9, 1993 for three Southern California locations: Central Los Angeles, Azusa, and Riverside. Predictions indicate increasing surface-level O3 concentrations with distance downwind, in line with observations. Surface-level and vertically averaged P(O3) values peak during midday and are highest downwind; surface P(O3) values are greater than vertically averaged values. Surface OPEs generally are highest downwind and peak during midday in downwind locations. In contrast, peaks occur in early morning and late afternoon in the vertically averaged case. Vertically averaged OPEs tend to be greater than those for the surface. Total reactivities are highest in upwind surface locations and peak during rush hours; vertically averaged reactivities are smaller and tend to be more uniform temporally and spatially. Total reactivity has large contributions from CO, alkanes, alkenes, aldehydes, unsubstituted monoaromatics, and secondary organics. Calculations using estimated emissions for 2010 result in decreases in P(O3) values and reactivities but increases in OPEs.

26 CFR 1.411(d)-3 - Section 411(d)(6) protected benefits.

Code of Federal Regulations, 2011 CFR

2011-04-01

... an annual benefit of 2% of career average pay times years of service commencing at normal retirement... an annual benefit of 1.3% of final pay times years of service, with final pay computed as the average... has 16 years of service, M's career average pay is $37,500, and the average of M's highest 3...

Broadband turbulent spectra in gamma-ray burst light curves

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van Putten, Maurice H. P. M.; Guidorzi, Cristiano; Frontera, Filippo, E-mail: mvp@sejong.ac.kr

2014-05-10

Broadband power density spectra offer a window to understanding turbulent behavior in the emission mechanism and, at the highest frequencies, in the putative inner engines powering long gamma-ray bursts (GRBs). We describe a chirp search method alongside Fourier analysis for signal detection in the Poisson noise-dominated, 2 kHz sampled, BeppoSAX light curves. An efficient numerical implementation is described in O(Nnlog n) operations, where N is the number of chirp templates and n is the length of the light-curve time series, suited for embarrassingly parallel processing. For the detection of individual chirps over a 1 s duration, the method is onemore » order of magnitude more sensitive in signal-to-noise ratio than Fourier analysis. The Fourier-chirp spectra of GRB 010408 and GRB 970816 show a continuation of the spectral slope with up to 1 kHz of turbulence identified in low-frequency Fourier analysis. The same continuation is observed in an average spectrum of 42 bright, long GRBs. An outlook on a similar analysis of upcoming gravitational wave data is included.« less

All-fiber mode-locked laser oscillator with pulse energy of 34 nJ using a single-walled carbon nanotube saturable absorber.

PubMed

Jeong, Hwanseong; Choi, Sun Young; Rotermund, Fabian; Cha, Yong-Ho; Jeong, Do-Young; Yeom, Dong-Il

2014-09-22

We demonstrate a dissipative soliton fiber laser with high pulse energy (>30 nJ) based on a single-walled carbon nanotube saturable absorber (SWCNT-SA). In-line SA that evanescently interacts with the high quality SWCNT/polymer composite film was fabricated under optimized conditions, increasing the damage threshold of the saturation fluence of the SA to 97 mJ/cm(2). An Er-doped mode-locked all-fiber laser operating at net normal intra-cavity dispersion was built including the fabricated in-line SA. The laser stably delivers linearly chirped pulses with a pulse duration of 12.7 ps, and exhibits a spectral bandwidth of 12.1 nm at the central wavelength of 1563 nm. Average power of the laser output is measured as 335 mW at an applied pump power of 1.27 W. The corresponding pulse energy is estimated to be 34 nJ at the fundamental repetition rate of 9.80 MHz; this is the highest value, to our knowledge, reported in all-fiber Er-doped mode-locked laser using an SWCNT-SA.

Deep geothermal resources in the Yangbajing Field, Tibet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao Ping; Jin Jian; Duo Ji

1997-12-31

Since the first well was bored in July 1997 in the Yangbajing geothermal field, more than 80 wells have been drilled. The total of installed capacity is 25.18MWe for geothermal power plant that has generated about 1.0 x 10{sup 9} kWh electricity in all. Temperatures inside shallow reservoir are in the range from 150{degrees}C to 165{degrees}C. No high-temperature field if found below the shallow reservoir in the southern part. In order to enlarge the installed capacity and solve pressure decline in current productive wells, an exploration project of deep geothermal resources has been carried out in the northern part. Themore » highest temperature of 329{degrees}C was detected in well ZK4002 at 1850m depth in 1994. Well ZK4001 drilled in 1996 flows out high-enthalpy thermal fluid at the wellhead, in which the average temperature is 248{degrees}C in the feeding zones. There is a great potential for power generation in the northern part. The exploitation of deep geothermal resources would effect the production of existing wells.« less

Health hazard evaluation report HETA 96-0137-2607, Yankee Atomic Electric Company, Rowe, Massachusetts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sylvain, D.C.

1996-10-01

In response to a request from the Health and Safety Supervisor at the Yankee Nuclear Power Station (SIC-4911), Rowe, Massachusetts, an investigation was begun into ozone (10028156) exposure during plasma arc cutting and welding. Welders had reported chest tightness, dry cough, and throat and bronchial irritation. The nuclear power station was in the process of being decommissioned, and workers were dismantling components using welding and cutting methods. Of the operations observed during the site visit, the highest ozone concentrations were generated during plasma arc cutting, followed by metal inert gas (MIG) welding and arc welding. During plasma arc cutting themore » average and peak concentrations exceeded the NIOSH ceiling recommended exposure limit of 0.1 part per million. The author concludes that ozone exposure during plasma arc cutting and MIG welding presented a health hazard to welders. The author recommends that improvements be made in the local exhaust ventilation, that nitrogen-dioxide levels be monitored during hot work, and that many exposed workers wear protective clothing, use ultraviolet blocking lotion, and continue the use appropriate shade of eye protection.« less

Assessment of risk factors for death in electrical injury.

PubMed

Dokov, William

2009-02-01

Fatal high-voltage injuries present a problem which has not yet been studied sufficiently in the context of interaction between the human body and electricity, as a technical, anthropogenic and natural phenomenon. The forensic medicine records of 291 cases of death caused by high-voltage current for a 41-year-long period (1965-2006) were examined in retrospect. The descriptive statistical analyses were made using the SPSS 11.0 software. Death was found to result most commonly from contact between the deceased and elements of the power transmission and distribution grid: (41.24%), and from the action of lightning: (32.3%), the difference in their relative share being insignificant. Much more rarely, death was due to contact with construction and repair electrical devices: (7.56%), or with elements of the power transport railway infrastructure: (6.87%). Death resulting from contact with agricultural electrical devices was only occasional: (0.68%). The victims' average age was 36.19 years. Our analysis indicates that the relative share (43.98%) of the victims is the highest in the age period between 25 and 44. The ratio between women and men is 1:21.38.

Do Low-Income Students Have Equal Access to the Highest-Performing Teachers? NCEE Evaluation Brief. NCEE 2011-4016

ERIC Educational Resources Information Center

Glazerman, Steven; Max, Jeffrey

2011-01-01

This brief describes the prevalence of highest-performing teachers in ten purposely selected districts across seven states. The overall patterns indicate that low-income students have unequal access, on average, to the district's highest-performing teachers at the middle school level but not at the elementary level. However, there is evidence of…

Tidal Energy Resource Assessment for McMurdo Station, Antarctica

DTIC Science & Technology

2016-12-01

highest power coefficient possible, only to provide a high- fidelity data set for a simple geometry turbine model at reasonably high blade chord Reynolds...highest power coefficient possible, only to provide a high-fidelity data set for a simple geometry turbine model at reasonably high blade chord...Reynolds numbers. Tip speed ratio, , is defined as = where is the anglular velocity of the blade and is the

High-Average-Power Diffraction Pulse-Compression Gratings Enabling Next-Generation Ultrafast Laser Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alessi, D.

Pulse compressors for ultrafast lasers have been identified as a technology gap in the push towards high peak power systems with high average powers for industrial and scientific applications. Gratings for ultrashort (sub-150fs) pulse compressors are metallic and can absorb a significant percentage of laser energy resulting in up to 40% loss as well as thermal issues which degrade on-target performance. We have developed a next generation gold grating technology which we have scaled to the petawatt-size. This resulted in improvements in efficiency, uniformity and processing as compared to previous substrate etched gratings for high average power. This new designmore » has a deposited dielectric material for the grating ridge rather than etching directly into the glass substrate. It has been observed that average powers as low as 1W in a compressor can cause distortions in the on-target beam. We have developed and tested a method of actively cooling diffraction gratings which, in the case of gold gratings, can support a petawatt peak power laser with up to 600W average power. We demonstrated thermo-mechanical modeling of a grating in its use environment and benchmarked with experimental measurement. Multilayer dielectric (MLD) gratings are not yet used for these high peak power, ultrashort pulse durations due to their design challenges. We have designed and fabricated broad bandwidth, low dispersion MLD gratings suitable for delivering 30 fs pulses at high average power. This new grating design requires the use of a novel Out Of Plane (OOP) compressor, which we have modeled, designed, built and tested. This prototype compressor yielded a transmission of 90% for a pulse with 45 nm bandwidth, and free of spatial and angular chirp. In order to evaluate gratings and compressors built in this project we have commissioned a joule-class ultrafast Ti:Sapphire laser system. Combining the grating cooling and MLD technologies developed here could enable petawatt laser systems to operate at 50kW average power.« less

[Effects of training of human intestinal parasitic diseases for basic health staff in Jiangsu Province].

PubMed

Jiang, Wen-cai; Li, Jian; Xu, Xiang-zhen; Shen, Ming-xue; Jin, Xiao-lin

2013-08-01

To evaluate the effect of the training of human intestinal parasitic diseases for basic health staff. A workshop including theory courses and practical operations was carried out. At the end of the workshop, the effects were evaluated through the examinations of theory and film-reading. The total score of film-reading was one hundred including reading ten modified thick Kato-Katz slides in five minutes per slide. The results were analyzed statistically with SAS 9.0. There were 162 trainees from 13 cities. All of them took part in the final examination. The highest score of theory test was 99 and the lowest was 60 with the average of 86.3. The average score of the female was higher than that of the male, and the average score of 30-40 years' age group was higher than that of the other groups. The average score of the staff in Northern Jiangsu Province was higher than that of the staff in southern area and middle area of Jiangsu Province (P < 0.05). The highest score of film-reading was 100 and the lowest score was 20 with the average of 73.4. Among the total 9 species, the egg detection rates of five species were more than 60.00%. The detection rate of Trichuris trichiura was highest (88.17%) and the rate of Taenia was only 14.7%. The total average score of the staff in Nanjing City was highest (181.3) and the score of the staff in Changzhou City was lowest (138.3). There were significant differences among different regions (P < 0.05). The technical capability of examining the human intestinal parasitic diseases of basic health staff is different among the different regions of Jiangsu Province. We still need to strengthen the capability of pathogen detection for basic health staff.

Concurrent validity, discriminatory power and feasibility of the instrument for Identification of Parents At Risk for child Abuse and Neglect (IPARAN)

PubMed Central

Horrevorts, Esther M B; van Grieken, Amy; Mieloo, Cathelijne L; Hafkamp-de Groen, Esther; Bannink, Rienke; Bouwmeester-Landweer, Merian B R; Broeren, Suzanne; Raat, Hein

2017-01-01

Objectives To determine the feasibility, concurrent validity and discriminatory power of the instrument for Identification of Parents At Risk for child Abuse and Neglect (IPARAN) among Dutch parents with a newborn child. Setting Community paediatrics. Participants Data from a controlled trial were used. In total, 2659 Dutch parents with a newborn child were invited to participate. Of the 2659 parents, 759 parents filled in the consent form and participated in the study. Primary and secondary outcome measures Concurrent validity was determined by calculating correlations—using the Pearson’s correlation (r)—between the IPARAN score and related constructs from the following instruments: the Empowerment Questionnaire 2.0, the Family Functioning Questionnaire and the Parenting Stress Questionnaire. Discriminatory power was determined by calculating receiver operating characteristic (ROC) curves between high-risk mothers and low-risk mothers according to their scores on the related constructs. Feasibility was determined by examining the percentage of missing answers. Results In terms of concurrent validity, we found that 3 out of 12 correlations between the IPARAN score and related constructs were strong (ie, r>0.50) and 4 out of 12 were medium (ie, r=0.30–0.49). In terms of discriminatory power, mothers with a score in the borderline/clinical range or lowest 10 percent (P10) range of the related constructs (high-risk mothers) had a higher IPARAN score than mothers with a score in the normal range or highest 90 percent (P90) range of the related constructs (low-risk mothers). Effect sizes varied from d=0.37 to d=1.93, and the area under the ROC curve varied from 0.62 to 0.93. Regarding feasibility, the part of the IPARAN filled in by the mother had on average 0.7% missing answers, whereas the part of the IPARAN filled in by the father had on average 1.7% missing answers. Conclusion The results of this study support the concurrent validity, discriminatory power and feasibility of the IPARAN among a population of Dutch parents with a newborn child. PMID:28838892

Comparison of Medical and Consumer Wireless EEG Systems for Use in Clinical Trials.

PubMed

Ratti, Elena; Waninger, Shani; Berka, Chris; Ruffini, Giulio; Verma, Ajay

2017-01-01

Objectives: To compare quantitative EEG signal and test-retest reliability of medical grade and consumer EEG systems. Methods: Resting state EEG was acquired by two medical grade (B-Alert, Enobio) and two consumer (Muse, Mindwave) EEG systems in five healthy subjects during two study visits. EEG patterns, power spectral densities (PSDs) and test/retest reliability in eyes closed and eyes open conditions were compared across the four systems, focusing on Fp1, the only common electrode. Fp1 PSDs were obtained using Welch's modified periodogram method and averaged for the five subjects for each visit. The test/retest results were calculated as a ratio of Visit 1/Visit 2 Fp1 channel PSD at each 1 s epoch. Results: B-Alert, Enobio, and Mindwave Fp1 power spectra were similar. Muse showed a broadband increase in power spectra and the highest relative variation across test-retest acquisitions. Consumer systems were more prone to artifact due to eye blinks and muscle movement in the frontal region. Conclusions: EEG data can be successfully collected from all four systems tested. Although there was slightly more time required for application, medical systems offer clear advantages in data quality, reliability, and depth of analysis over the consumer systems. Significance: This evaluation provides evidence for informed selection of EEG systemsappropriate for clinical trials.

MHD mixed convection analysis of non-Newtonian power law fluid in an open channel with round cavity

NASA Astrophysics Data System (ADS)

Bose, Pritom; Rakib, Tawfiqur; Das, Sourav; Rabbi, Khan Md.; Mojumder, Satyajit

2017-06-01

In this study, magneto-hydrodynamic (MHD) mixed convection flow through a channel with a round cavity at bottom wall using non-Newtonian power law fluid is analysed numerically. The cavity is kept at uniformly high temperature whereas rest of the bottom wall is insulated and top wall of the channel is maintained at a temperature lower than cavity temperature. Grid independency test and code validation are performed to justify the computational accuracy before solving the present problem. Galerkin weighted residual method is appointed to solve the continuity, momentum and energy equations. The problem is solved for wide range of pertinent parameters like Rayleigh number (Ra= 103 - 105), Hartmann number (Ha= 0 - 60) and power law index (n= 0.5 - 1.5) at constant Richardson number Ri= 1.0. The flow and thermal field have been thoroughly discussed through streamline and isothermal lines respectively. The heat transfer performance of the given study is illustrated by average Nusselt number plots. Result of this investigation indicates that heat transfer is highest for dilatant fluids at this configuration and they perform better (47% more heat transfer) in absence of magnetic field. The retardation of heat transfer is offset by shear thickening nature of non-Newtonian fluid.

Applications of high average power nonlinear optics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Velsko, S.P.; Krupke, W.F.

1996-02-05

Nonlinear optical frequency convertors (harmonic generators and optical parametric oscillators are reviewed with an emphasis on high average power performance and limitations. NLO materials issues and NLO device designs are discussed in reference to several emerging scientific, military and industrial commercial applications requiring {approx} 100 watt average power level in the visible and infrared spectral regions. Research efforts required to enable practical {approx} 100 watt class NLO based laser systems are identified.

High average power pockels cell

DOEpatents

Daly, Thomas P.

1991-01-01

A high average power pockels cell is disclosed which reduces the effect of thermally induced strains in high average power laser technology. The pockels cell includes an elongated, substantially rectangular crystalline structure formed from a KDP-type material to eliminate shear strains. The X- and Y-axes are oriented substantially perpendicular to the edges of the crystal cross-section and to the C-axis direction of propagation to eliminate shear strains.

14 CFR 29.1049 - Hovering cooling test procedures.

Code of Federal Regulations, 2010 CFR

2010-01-01

... minutes after the occurrence of the highest temperature recorded; and (b) With maximum continuous power... five minutes after the occurrence of the highest temperature recorded. Induction System ...

14 CFR 29.1049 - Hovering cooling test procedures.

Code of Federal Regulations, 2014 CFR

2014-01-01

... minutes after the occurrence of the highest temperature recorded; and (b) With maximum continuous power... five minutes after the occurrence of the highest temperature recorded. Induction System ...

14 CFR 29.1049 - Hovering cooling test procedures.

Code of Federal Regulations, 2012 CFR

2012-01-01

... minutes after the occurrence of the highest temperature recorded; and (b) With maximum continuous power... five minutes after the occurrence of the highest temperature recorded. Induction System ...

14 CFR 29.1049 - Hovering cooling test procedures.

Code of Federal Regulations, 2011 CFR

2011-01-01

... minutes after the occurrence of the highest temperature recorded; and (b) With maximum continuous power... five minutes after the occurrence of the highest temperature recorded. Induction System ...

14 CFR 29.1049 - Hovering cooling test procedures.

Code of Federal Regulations, 2013 CFR

2013-01-01

... minutes after the occurrence of the highest temperature recorded; and (b) With maximum continuous power... five minutes after the occurrence of the highest temperature recorded. Induction System ...

Frequencies of chromosomal inversions in Drosophila melanogaster in Fukushima after the nuclear power plant accident.

PubMed

Itoh, Masanobu; Kajihara, Ryutaro; Kato, Yasuko; Takano-Shimizu, Toshiyuki; Inoue, Yutaka

2018-01-01

In order to investigate genetic impact of a large amount of radionuclides released by the Fukushima Dai-ichi Nuclear Power Plant accident in 2011, we surveyed 2,304 haploid genomes of Drosophila melanogaster collected in three localities in Fukushima in 2012 and 2013 for chromosomal inversions. No unique inversion was found in 298 genomes in 2012 and only two in 2,006 genomes in 2013. The observed frequencies were even lower than the long-term average frequency of unique inversions in Japan. The common cosmopolitan inversions were also examined in Fukushima, Kyoto, and Iriomote (Okinawa) in 2012. Among three samples in Fukushima, the flies in Iizaka, where environmental radiation level was the highest, showed the lowest frequency of In(2L)t, but the highest frequency of In(3R)P, contrary to the expectation of decreasing of their frequencies in higher polluted areas. These results suggest that, at this level of genetic analysis, Fukushima populations of D. melanogaster would not have been negatively impacted following the release of radionuclides. Transposable P-element mobility was not likely to induce DNA damage solely or synergistically with radioactivity, because their transposition activity was totally repressed in the Fukushima strains. However, it should be noted that, because of limitations in access to the exclusion zone, we could only sample the populations in areas of relatively low radioactive contamination (0.39-0.63 μSv/h). Therefore, the present study is likely to be underpowered to detect any effects that might be expected in heavily contaminated areas.

Displacement cascades and defects annealing in tungsten, Part I: Defect database from molecular dynamics simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Setyawan, Wahyu; Nandipati, Giridhar; Roche, Kenneth J.

Molecular dynamics simulations have been used to generate a comprehensive database of surviving defects due to displacement cascades in bulk tungsten. Twenty-one data points of primary knock-on atom (PKA) energies ranging from 100 eV (sub-threshold energy) to 100 keV (~780 × Ed, where Ed = 128 eV is the average displacement threshold energy) have been completed at 300 K, 1025 K and 2050 K. Within this range of PKA energies, two regimes of power-law energy-dependence of the defect production are observed. A distinct power-law exponent characterizes the number of Frenkel pairs produced within each regime. The two regimes intersect atmore » a transition energy which occurs at approximately 250 × Ed. The transition energy also marks the onset of the formation of large self-interstitial atom (SIA) clusters (size 14 or more). The observed defect clustering behavior is asymmetric, with SIA clustering increasing with temperature, while the vacancy clustering decreases. This asymmetry increases with temperature such that at 2050 K (~0.5 Tm) practically no large vacancy clusters are formed, meanwhile large SIA clusters appear in all simulations. The implication of such asymmetry on the long-term defect survival and damage accumulation is discussed. In addition, <100> {110} SIA loops are observed to form directly in the highest energy cascades, while vacancy <100> loops are observed to form at the lowest temperature and highest PKA energies, although the appearance of both the vacancy and SIA loops with Burgers vector of <100> type is relatively rare.« less

Frequencies of chromosomal inversions in Drosophila melanogaster in Fukushima after the nuclear power plant accident

PubMed Central

Kajihara, Ryutaro; Kato, Yasuko; Takano-Shimizu, Toshiyuki; Inoue, Yutaka

2018-01-01

In order to investigate genetic impact of a large amount of radionuclides released by the Fukushima Dai-ichi Nuclear Power Plant accident in 2011, we surveyed 2,304 haploid genomes of Drosophila melanogaster collected in three localities in Fukushima in 2012 and 2013 for chromosomal inversions. No unique inversion was found in 298 genomes in 2012 and only two in 2,006 genomes in 2013. The observed frequencies were even lower than the long-term average frequency of unique inversions in Japan. The common cosmopolitan inversions were also examined in Fukushima, Kyoto, and Iriomote (Okinawa) in 2012. Among three samples in Fukushima, the flies in Iizaka, where environmental radiation level was the highest, showed the lowest frequency of In(2L)t, but the highest frequency of In(3R)P, contrary to the expectation of decreasing of their frequencies in higher polluted areas. These results suggest that, at this level of genetic analysis, Fukushima populations of D. melanogaster would not have been negatively impacted following the release of radionuclides. Transposable P-element mobility was not likely to induce DNA damage solely or synergistically with radioactivity, because their transposition activity was totally repressed in the Fukushima strains. However, it should be noted that, because of limitations in access to the exclusion zone, we could only sample the populations in areas of relatively low radioactive contamination (0.39–0.63 μSv/h). Therefore, the present study is likely to be underpowered to detect any effects that might be expected in heavily contaminated areas. PMID:29420572

Resonantly cladding-pumped Yb-free Er-doped LMA fiber laser with record high power and efficiency.

PubMed

Zhang, Jun; Fromzel, Viktor; Dubinskii, Mark

2011-03-14

We report the results of our power scaling experiments with resonantly cladding-pumped Er-doped eye-safe large mode area (LMA) fiber laser. While using commercial off-the-shelf LMA fiber we achieved over 88 W of continuous-wave (CW) single transverse mode power at ~1590 nm while pumping at 1532.5 nm. Maximum observed optical-to-optical efficiency was 69%. This result presents, to the best of our knowledge, the highest power reported from resonantly-pumped Yb-free Er-doped LMA fiber laser, as well as the highest efficiency ever reported for any cladding-pumped Er-doped laser, either Yb-co-doped or Yb-free.

75 FR 68733 - Approval and Promulgation of One-Year Extension for Attaining the 1997 8-Hour Ozone Standard for...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-09

... Philadelphia Area's 4th highest daily 8-hour monitored ozone value during the 2009 ozone season at each monitor...-year extensions of the attainment date if: (a) For the first 1-year extension, the area's 4th highest... second 1-year extension, the area's 4th highest daily 8-hour value, averaged over both the original...

Expected indoor 222Rn levels in counties with very high and very low lung cancer rates.

PubMed

Cohen, B L

1989-12-01

Counties in the U.S. with high lung cancer rates should have higher average 222Rn levels than counties with low lung cancer rates, assuming the average 222Rn level in a county is not correlated with other factors that cause lung cancer. The magnitude of this effect was calculated, using the absolute risk model, the relative risk model, and an intermediate model, for females who died in 1950-1969. The results were similar for all three models. We concluded that, ignoring migration, the average Rn level in the highest lung cancer counties should be about three times higher than in the lowest lung cancer counties according to the theory. Preliminary data are presented indicating that the situation is quite the opposite: The average Rn level in the highest lung cancer counties was only about one-half that in the lowest lung cancer counties.

Effect of the target power density on high-power impulse magnetron sputtering of copper

NASA Astrophysics Data System (ADS)

Kozák, Tomáš

2012-04-01

We present a model analysis of high-power impulse magnetron sputtering of copper. We use a non-stationary global model based on the particle and energy conservation equations in two zones (the high density plasma ring above the target racetrack and the bulk plasma region), which makes it possible to calculate time evolutions of the averaged process gas and target material neutral and ion densities, as well as the fluxes of these particles to the target and substrate during a pulse period. We study the effect of the increasing target power density under conditions corresponding to a real experimental system. The calculated target current waveforms show a long steady state and are in good agreement with the experimental results. For an increasing target power density, an analysis of the particle densities shows a gradual transition to a metal dominated discharge plasma with an increasing degree of ionization of the depositing flux. The average fraction of target material ions in the total ion flux onto the substrate is more than 90% for average target power densities higher than 500 W cm-2 in a pulse. The average ionized fraction of target material atoms in the flux onto the substrate reaches 80% for a maximum average target power density of 3 kW cm-2 in a pulse.

Hazelwood Interim Storage Site: Annual site environment report, Calendar year 1985

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1986-11-01

The Hazelwood Interim Storage Site (HISS) is presently used for the storage of low-level radioactively contaminated soils. Monitoring results show that the HISS is in compliance with DOE Derived Concentration Guides (DCGs) and radiation protection standards. During 1985, annual average radon concentrations ranged from 10 to 23% of the DCG. The highest external dose rate at the HISS was 287 mrem/yr. The measured background dose rate for the HISS area is 99 mrem/yr. The highest average annual concentration of uranium in surface water monitored in the vicinity of the HISS was 0.7% of the DOE DCG; for /sup 226/Ra itmore » was 0.3% of the applicable DCG, and for /sup 230/Th it was 1.7%. In groundwater, the highest annual average concentration of uranium was 12% of the DCG; for /sup 226/Ra it was 3.6% of the applicable DCG, and for /sup 230/Th it was 1.8%. While there are no concentration guides for stream sediments, the highest concentration of total uranium was 19 pCi/g, the highest concentration of /sup 226/Ra was 4 pCi/g, and the highest concentration of /sup 230/Th was 300 pCi/g. Radon concentrations, external gamma dose rates, and radionuclide concentrations in groundwater at the site were lower than those measured in 1984; radionuclide concentrations in surface water were roughly equivalent to 1984 levels. For sediments, a meaningful comparison with 1984 concentrations cannot be made since samples were obtained at only two locations and were only analyzed for /sup 230/Th. The calculated radiation dose to the maximally exposed individual at the HISS, considering several exposure pathways, was 5.4 mrem, which is 5% of the radiation protection standard.« less

Average focal length and power of a section of any defined surface.

PubMed

Kaye, Stephen B

2010-04-01

To provide a method to allow calculation of the average focal length and power of a lens through a specified meridian of any defined surface, not limited to the paraxial approximations. University of Liverpool, Liverpool, United Kingdom. Functions were derived to model back-vertex focal length and representative power through a meridian containing any defined surface. Average back-vertex focal length was based on the definition of the average of a function, using the angle of incidence as an independent variable. Univariate functions allowed determination of average focal length and power through a section of any defined or topographically measured surface of a known refractive index. These functions incorporated aberrations confined to the section. The proposed method closely approximates the average focal length, and by inference power, of a section (meridian) of a surface to a single or scalar value. It is not dependent on the paraxial and other nonconstant approximations and includes aberrations confined to that meridian. A generalization of this method to include all orthogonal and oblique meridians is needed before a comparison with measured wavefront values can be made. Copyright (c) 2010 ASCRS and ESCRS. Published by Elsevier Inc. All rights reserved.

High Power Broadband Millimeter Wave TWTs

NASA Astrophysics Data System (ADS)

James, Bill G.

1998-04-01

In the early 1980's the requirement for high power broadband millimeter wave sources encouraged the development of microwave vacuum device amplifiers for radar and communication systems. Many government funded programs were implemented for the development of high power broadband millimeter wave amplifiers that would meet the needs of the high power community. The tube design capable of meeting these goals was the slow wave coupled cavity traveling wave device, which had a proven technology base at the lower frequencies (X Band). However scaling this technology to the millimeter frequencies had severe shortcomings in both thermal and manufacturing design. These shortcomings were overcome with the development of the Ladder Circuit technology. In conjunction with the circuit development high power electron beam systems had to be developed for the generation of high rf powers. These beam systems had to be capable of many megawatts of beam power density and high current densities. The cathode technology required to be capable of operating at current densities of 10 amperes per square centimeter at long pulse lengths and high duty cycle. Since the introduction of the Ladder Circuit technology a number of high power broadband millimeter wave amplifiers have been developed and deployed in operating radar and communication systems. Broadband millimeter wave sources have been manufactured in the frequency range from 27 GHz to 100 GHz with power levels ranging from 100 watts CW to 10 kilowatts Peak at W band over a 2 GHz bandwidth. Also a 50 kW peak power and 10 kW average power device at Ka band with 2 GHz bandwidth has been developed. Today the power levels achieved by these devices are nearing the limits of this technology; therefore to gain a significant increase in power at the millimeter wave frequencies, other technologies will have to be considered, particularly fast wave devices. This paper will briefly review the ladder circuit technology and present the designs of a number of broadband high power devices developed at Ka and W band. The discussion will include the beam systems employed in these devices which are the highest power density linear beams generated to date. In conclusion the limits of the power generating capability of this technology will be presented.

Heat profiling of phacoemulsification tip using a thermal scanning camera.

PubMed

Ngo, Wei Kiong; Lim, Louis W; Tan, Colin S H; Heng, Wee Jin

2013-12-01

An experimental study to measure the heat profile of the phacoemulsification (phaco) tip using standard continuous phaco and hyperpulse phaco with and without waveform power modulation in the Millennium Microsurgical System with Custom Control Software (CCS). The phaco tip was imaged in air using a thermal camera. The highest temperature was measured 15 s after application of phaco power. Continuous, hyperpulse and waveform power modulations of the Millennium Microsurgical System were used with different power settings (20, 50 and 100 %) and duty cycles (40, 60 and 90 %), with the irrigation turned on and off. Using continuous phaco with the irrigation on, the phaco tip temperature remains <28.0 °C. With irrigation off, the temperature is higher compared to irrigation on but still remains <45.0 °C. Comparing the temperatures for all three power modulations when irrigation is on, at each phaco power and duty cycle setting, the temperature of the phaco tip is highest with continuous phaco, followed by hyperpulse with rise time 1, then hyperpulse with rise time 2. When irrigation is off, the highest temperatures are recorded using the hyperpulse with rise time 2, followed by continuous phaco, then hyperpulse with rise time 1. Hyperpulse and waveform modulations reduce heat generation compared to the continuous mode when irrigation is turned on. Lower duty cycles and lower ultrasound power produce less heat at the phaco tip.

Investigation of the Loads on a Conventional Front and Rear Sliding Canopy

NASA Technical Reports Server (NTRS)

Dexter, Howard E.; Rickey, Edward A.

1947-01-01

As one phase of a comprehensive canopy load investigation, conventional front and rear sliding canopies which are typified by installation on the SB2C-4E airplane, were tested in the Langley full-scale tunnel to determine the pressure distributions and the aerodynamic loads on the canopies. A preliminary analysis of the results of these tests is presented in this report. Plots are presented that show the distribution of pressure at four longitudinal stations through each canopy for a range of conditions selected to determine the effects of varying canopy position, yaw, lift coefficient, and power. The results indicate that the maximum loads, based on the external-internal pressure differential, for the front and rear canopies were obtained with the airplane simulating the high speed flight condition. The highest loading on the front canopy was in the exploding direction for the configuration with the front and rear canopies closed. The highest loads on the rear canopy were in the crushing direction with the front canopy open and the rear canopy closed. For most of the simulated flight conditions, the highest loads on the front canopy, per unit area, were over twice as great as the highest loads on the rear canopy when the comparison was made for the most critical canopy configuration in each case. The external pressure distribution over the front and rear canopies, which were fairly symmetrical to 0 degree angle of yaw, were greatly distorted at other yaw attitudes, particularly for the propeller operating conditions. These distorted pressure distributions resulted in local exploding and crushing loads on both canopies which were often considerably higher than the average canopy loads.

Optoelectronic studies on heterocyclic bases of deoxyribonucleic acid for DNA photonics.

PubMed

El-Diasty, Fouad; Abdel-Wahab, Fathy

2015-10-01

The optoelectronics study of large molecules, particularly π-stacking molecules, such as DNA is really an extremely difficult task. We perform first electronic structure calculations on the heterocyclic bases of 2'-deoxyribonucleic acid based on Lorentz-Fresnel dispersion theory. In the UV-VIS range of spectrum, many of the optoelectronic parameters for DNA four bases namely adenine, guanine, cytosine and thymine are calculated and discussed. The results demonstrate that adenine has the highest hyperpolarizability, whereas thymine has the lowest hyperpolarizability. Cytosine has the lower average oscillator energy and the higher lattice energy. Thymine infers the most stable nucleic base with the lower phonon energy. Thymine also has the highest average oscillator energy and the lower lattice energy. Moreover, the four nucleic acid bases have large band gap energies less than 5 eV with a semiconducting behavior. Guanine shows the smallest band gap and the highest Fermi level energy, whereas adenine elucidates the highest band gap energy. Copyright © 2015. Published by Elsevier B.V.

Impact of boiling on free and bound phenolic profile and antioxidant activity of commercial gluten-free pasta.

PubMed

Rocchetti, Gabriele; Lucini, Luigi; Chiodelli, Giulia; Giuberti, Gianluca; Montesano, Domenico; Masoero, Francesco; Trevisan, Marco

2017-10-01

Cooking by boiling dry pasta could have varying degrees of influence on nutritional and functional components. In the present study, its effect on total phenolic content and antioxidant capacity, as well as on the comprehensive profile of free and bound phenolics, was investigated in six commercial gluten-free (GF) pasta products. Overall, the heat treatment caused a significant reduction (P<0.01) of the total phenolic content as well as FRAP reducing power and ORAC radical scavenging, with significant differences among the pasta samples considered. The highest values were recorded in free phenolic fraction remaining in black rice (41mggallic acid equivalents100g -1 and 25mmolTrolox Equivalents100g -1 ) and quinoa (24mggallic acid equivalents100g -1 and 14mmolTrolox Equivalents100g -1 ) cooked GF pasta. Significant correlations (P<0.01) could be found between total phenolics and both the antioxidant capacity assays performed. UHPLC-ESI/QTOF-MS mass profiling allowed confirming the spectrophotometric results, while identifying the amount of free and bound fractions. Among phenolic classes, lignans exhibited the highest decrease during the cooking process, followed by stilbenes and flavonoids. However, phenolic acids and other phenolics showed the highest stability. Furthermore, cooking by boiling strongly lowered the bound-to-free ratio of phenolic compounds, by an averaged factor ranging from 14-folds for flavonoids to 5-folds for other classes of phenolics. Copyright © 2017 Elsevier Ltd. All rights reserved.

High-average-power 2 μm few-cycle optical parametric chirped pulse amplifier at 100 kHz repetition rate.

PubMed

Shamir, Yariv; Rothhardt, Jan; Hädrich, Steffen; Demmler, Stefan; Tschernajew, Maxim; Limpert, Jens; Tünnermann, Andreas

2015-12-01

Sources of long wavelengths few-cycle high repetition rate pulses are becoming increasingly important for a plethora of applications, e.g., in high-field physics. Here, we report on the realization of a tunable optical parametric chirped pulse amplifier at 100 kHz repetition rate. At a central wavelength of 2 μm, the system delivered 33 fs pulses and a 6 W average power corresponding to 60 μJ pulse energy with gigawatt-level peak powers. Idler absorption and its crystal heating is experimentally investigated for a BBO. Strategies for further power scaling to several tens of watts of average power are discussed.

Single and Multi-Pulse Low-Energy Conical Theta Pinch Inductive Pulsed Plasma Thruster Performance

NASA Technical Reports Server (NTRS)

Hallock, A. K.; Martin, A. K.; Polzin, K. A.; Kimberlin, A. C.; Eskridge, R. H.

2013-01-01

Impulse bits produced by conical theta-pinch inductive pulsed plasma thrusters possessing cone angles of 20deg, 38deg, and 60deg, were quantified for 500J/pulse operation by direct measurement using a hanging-pendulum thrust stand. All three cone angles were tested in single-pulse mode, with the 38deg model producing the highest impulse bits at roughly 1 mN-s operating on both argon and xenon propellants. A capacitor charging system, assembled to support repetitively-pulsed thruster operation, permitted testing of the 38deg thruster at a repetition-rate of 5 Hz at power levels of 0.9, 1.6, and 2.5 kW. The average thrust measured during multiple-pulse operation exceeded the value obtained when the single-pulse impulse bit is multiplied by the repetition rate.

Hyperbolicity measures democracy in real-world networks

NASA Astrophysics Data System (ADS)

Borassi, Michele; Chessa, Alessandro; Caldarelli, Guido

2015-09-01

In this work, we analyze the hyperbolicity of real-world networks, a geometric quantity that measures if a space is negatively curved. We provide two improvements in our understanding of this quantity: first of all, in our interpretation, a hyperbolic network is "aristocratic", since few elements "connect" the system, while a non-hyperbolic network has a more "democratic" structure with a larger number of crucial elements. The second contribution is the introduction of the average hyperbolicity of the neighbors of a given node. Through this definition, we outline an "influence area" for the vertices in the graph. We show that in real networks the influence area of the highest degree vertex is small in what we define "local" networks (i.e., social or peer-to-peer networks), and large in "global" networks (i.e., power grid, metabolic networks, or autonomous system networks).

[Application of regression tree in analyzing the effects of climate factors on NDVI in loess hilly area of Shaanxi Province].

PubMed

Liu, Yang; Lü, Yi-he; Zheng, Hai-feng; Chen, Li-ding

2010-05-01

Based on the 10-day SPOT VEGETATION NDVI data and the daily meteorological data from 1998 to 2007 in Yan' an City, the main meteorological variables affecting the annual and interannual variations of NDVI were determined by using regression tree. It was found that the effects of test meteorological variables on the variability of NDVI differed with seasons and time lags. Temperature and precipitation were the most important meteorological variables affecting the annual variation of NDVI, and the average highest temperature was the most important meteorological variable affecting the inter-annual variation of NDVI. Regression tree was very powerful in determining the key meteorological variables affecting NDVI variation, but could not build quantitative relations between NDVI and meteorological variables, which limited its further and wider application.

Pulse compression of a high-power thin disk laser using rod-type fiber amplifiers.

PubMed

Saraceno, C J; Heckl, O H; Baer, C R E; Südmeyer, T; Keller, U

2011-01-17

We report on two pulse compressors for a high-power thin disk laser oscillator using rod-type fiber amplifiers. Both systems are seeded by a standard SESAM modelocked thin disk laser that delivers 16 W of average power at a repetition rate of 10.6 MHz with a pulse energy of 1.5 μJ and a pulse duration of 1 ps. We discuss two results with different fiber parameters with different trade-offs in pulse duration, average power, damage and complexity. The first amplifier setup consists of a Yb-doped fiber amplifier with a 2200 μm2 core area and a length of 55 cm, resulting in a compressed average power of 55 W with 98-fs pulses at a repetition rate of 10.6 MHz. The second system uses a shorter 36-cm fiber with a larger core area of 4500 μm2. In a stretcher-free configuration we obtained 34 W of compressed average power and 65-fs pulses. In both cases peak powers of > 30 MW were demonstrated at several μJ pulse energies. The power scaling limitations due to damage and self-focusing are discussed.

18 CFR 301.7 - Average System Cost methodology functionalization.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 18 Conservation of Power and Water Resources 1 2014-04-01 2014-04-01 false Average System Cost methodology functionalization. 301.7 Section 301.7 Conservation of Power and Water Resources FEDERAL ENERGY... ACT § 301.7 Average System Cost methodology functionalization. (a) Functionalization of each Account...

18 CFR 301.7 - Average System Cost methodology functionalization.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 18 Conservation of Power and Water Resources 1 2012-04-01 2012-04-01 false Average System Cost methodology functionalization. 301.7 Section 301.7 Conservation of Power and Water Resources FEDERAL ENERGY... ACT § 301.7 Average System Cost methodology functionalization. (a) Functionalization of each Account...

18 CFR 301.7 - Average System Cost methodology functionalization.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 18 Conservation of Power and Water Resources 1 2013-04-01 2013-04-01 false Average System Cost methodology functionalization. 301.7 Section 301.7 Conservation of Power and Water Resources FEDERAL ENERGY... ACT § 301.7 Average System Cost methodology functionalization. (a) Functionalization of each Account...

18 CFR 301.7 - Average System Cost methodology functionalization.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 18 Conservation of Power and Water Resources 1 2011-04-01 2011-04-01 false Average System Cost methodology functionalization. 301.7 Section 301.7 Conservation of Power and Water Resources FEDERAL ENERGY... ACT § 301.7 Average System Cost methodology functionalization. (a) Functionalization of each Account...

Computationally Efficient Resampling of Nonuniform Oversampled SAR Data

DTIC Science & Technology

2010-05-01

noncoherently . The resample data is calculated using both a simple average and a weighted average of the demodulated data. The average nonuniform...trials with randomly varying accelerations. The results are shown in Fig. 5 for the noncoherent power difference and Fig. 6 for and coherent power...simple average. Figure 5. Noncoherent difference between SAR imagery generated with uniform sampling and nonuniform sampling that was resampled

RF Design of a High Average Beam-Power SRF Electron Source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sipahi, Nihan; Biedron, Sandra; Gonin, Ivan

2016-06-01

There is a significant interest in developing high-average power electron sources, particularly in the area of electron sources integrated with Superconducting Radio Frequency (SRF) systems. For these systems, the electron gun and cathode parts are critical components for stable intensity and high-average powers. In this initial design study, we will present the design of a 9-cell accelerator cavity having a frequency of 1.3 GHz and the corresponding field optimization studies.

76 FR 13289 - Approval of One-Year Extension for Attaining the 1997 8-Hour Ozone Standard in the Baltimore...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-11

...). This extension is based on the air quality data for the 4th highest daily 8-hour monitored value during... first one-year extension, the area's 4th highest daily 8-hour average in the attainment year is 0.084 parts per million (ppm) or less. (b) For the second one-year extension, the area's 4th highest daily 8...

75 FR 68736 - Approval of One-Year Extension for Attaining the 1997 8-Hour Ozone Standard for the Delaware...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-09

... 4th highest daily 8-hour monitored ozone value during the 2009 ozone season is 0.084 parts per million... extensions of the attainment date if: (a) For the first 1-year extension, the area's 4th highest daily 8...'s 4th highest daily 8-hour value, averaged over both the original attainment year and the first...

Satellite chlorophyll off the British Columbia Coast, 1997-2010

NASA Astrophysics Data System (ADS)

Jackson, Jennifer M.; Thomson, Richard E.; Brown, Leslie N.; Willis, Peter G.; Borstad, Gary A.

2015-07-01

We examine the spatial and temporal variability of satellite-sensed sea surface chlorophyll off the west coast of North America from 1997 to 2010, with focus on coastal British Columbia. The variability in surface chlorophyll is complex. Whereas the spring bloom generates the highest phytoplankton concentration for coastal Alaska, the north and east coasts of Haida Gwaii, Queen Charlotte Sound, the Strait of Georgia, and coastal Oregon and California, it is the fall bloom that normally generates the highest concentration for the west coast of Vancouver Island, Juan de Fuca Strait, and the west coast of Washington. The highest satellite-sensed chlorophyll concentrations occur in the Strait of Georgia, where mean values are at least 2 times higher than elsewhere in the northeast Pacific. Moreover, the annual average surface chlorophyll concentration increased significantly in the Strait of Georgia during this period, with highest concentration observed during the near neutral ENSO conditions of the spring of 2007. The next highest concentrations occur off southwest Vancouver Island but have no statistically significant trend. The lowest average peak chlorophyll concentration is observed off Southern California. The timing of the highest chlorophyll concentration is latest off the coast of Washington and earliest off the coast of Southern California. Small increasing concentration trends are observed off the Washington and California coasts.

Dynamic Changes in Spectral and Spatial Signatures of High Frequency Oscillations in Rat Hippocampi during Epileptogenesis in Acute and Chronic Stages.

PubMed

Song, Pan-Pan; Xiang, Jing; Jiang, Li; Chen, Heng-Sheng; Liu, Ben-Ke; Hu, Yue

2016-01-01

To analyze spectral and spatial signatures of high frequency oscillations (HFOs), which include ripples and fast ripples (FRs, >200 Hz) by quantitatively assessing average and peak spectral power in a rat model of different stages of epileptogenesis. The lithium-pilocarpine model of temporal lobe epilepsy was used. The acute phase of epilepsy was assessed by recording intracranial electroencephalography (EEG) activity for 1 day after status epilepticus (SE). The chronic phase of epilepsy, including spontaneous recurrent seizures (SRSs), was assessed by recording EEG activity for 28 days after SE. Average and peak spectral power of five frequency bands of EEG signals in CA1, CA3, and DG regions of the hippocampus were analyzed with wavelet and digital filter. FRs occurred in the hippocampus in the animal model. Significant dynamic changes in the spectral power of FRS were identified in CA1 and CA3. The average spectral power of ripples increased at 20 min before SE ( p  < 0.05), peaked at 10 min before diazepam injection. It decreased at 10 min after diazepam ( p  < 0.05) and returned to baseline after 1 h. The average spectral power of FRs increased at 30 min before SE ( p  < 0.05) and peaked at 10 min before diazepam. It decreased at 10 min after diazepam ( p  < 0.05) and returned to baseline at 2 h after injection. The dynamic changes were similar between average and peak spectral power of FRs. Average and peak spectral power of both ripples and FRs in the chronic phase showed a gradual downward trend compared with normal rats 14 days after SE. The spectral power of HFOs may be utilized to distinguish between normal and pathologic HFOs. Ictal average and peak spectral power of FRs were two parameters for predicting acute epileptic seizures, which could be used as a new quantitative biomarker and early warning marker of seizure. Changes in interictal HFOs power in the hippocampus at the chronic stage may be not related to seizure occurrence.

Determinants of mobile phone output power in a multinational study: implications for exposure assessment.

PubMed

Vrijheid, M; Mann, S; Vecchia, P; Wiart, J; Taki, M; Ardoino, L; Armstrong, B K; Auvinen, A; Bédard, D; Berg-Beckhoff, G; Brown, J; Chetrit, A; Collatz-Christensen, H; Combalot, E; Cook, A; Deltour, I; Feychting, M; Giles, G G; Hepworth, S J; Hours, M; Iavarone, I; Johansen, C; Krewski, D; Kurttio, P; Lagorio, S; Lönn, S; McBride, M; Montestrucq, L; Parslow, R C; Sadetzki, S; Schüz, J; Tynes, T; Woodward, A; Cardis, E

2009-10-01

The output power of a mobile phone is directly related to its radiofrequency (RF) electromagnetic field strength, and may theoretically vary substantially in different networks and phone use circumstances due to power control technologies. To improve indices of RF exposure for epidemiological studies, we assessed determinants of mobile phone output power in a multinational study. More than 500 volunteers in 12 countries used Global System for Mobile communications software-modified phones (GSM SMPs) for approximately 1 month each. The SMPs recorded date, time, and duration of each call, and the frequency band and output power at fixed sampling intervals throughout each call. Questionnaires provided information on the typical circumstances of an individual's phone use. Linear regression models were used to analyse the influence of possible explanatory variables on the average output power and the percentage call time at maximum power for each call. Measurements of over 60,000 phone calls showed that the average output power was approximately 50% of the maximum, and that output power varied by a factor of up to 2 to 3 between study centres and network operators. Maximum power was used during a considerable proportion of call time (39% on average). Output power decreased with increasing call duration, but showed little variation in relation to reported frequency of use while in a moving vehicle or inside buildings. Higher output powers for rural compared with urban use of the SMP were observed principally in Sweden where the study covered very sparsely populated areas. Average power levels are substantially higher than the minimum levels theoretically achievable in GSM networks. Exposure indices could be improved by accounting for average power levels of different telecommunications systems. There appears to be little value in gathering information on circumstances of phone use other than use in very sparsely populated regions.

Buparvaquone Nanostructured Lipid Carrier: Development of an Affordable Delivery System for the Treatment of Leishmaniases.

PubMed

Monteiro, Lis Marie; Löbenberg, Raimar; Cotrim, Paulo Cesar; Barros de Araujo, Gabriel Lima; Bou-Chacra, Nádia

2017-01-01

Buparvaquone (BPQ), a veterinary drug, was formulated as nanostructured lipid carriers (NLC) for leishmaniases treatment. The formulation design addressed poor water solubility of BPQ and lack of human drug delivery system. The DSC/TG and microscopy methods were used for solid lipids screening. Softisan® 154 showed highest BPQ solubility in both methods. The BPQ solubility in liquid lipids using HPLC revealed Miglyol® 812 as the best option. Response surface methodology (RSM) was used to identify the optimal Softisan154 : Miglyol 812 ratios (7 : 10 to 2 : 1) and Kolliphor® P188 and Tween® 80 concentration (>3.0% w/w) aiming for z -average in the range of 100-300 nm for macrophage delivery. The NLC obtained by high-pressure homogenization showed low z -averages (<350 nm), polydispersity (<0.3), and encapsulation efficiency close to 100%. DSC/TG and microscopy in combination proved to be a powerful tool to select the solid lipid. The relationship among the variables, demonstrated by a linear mathematical model using RSM, allowed generating a design space. This design space showed the limits in which changes in the variables influenced the z -average. Therefore, these drug delivery systems have the potential to improve the availability of affordable medicines due to the low cost of raw materials, using well established, reliable, and feasible scale-up technology.

A multitracer approach to assess the spatial contamination pattern of hake (Merluccius merluccius) in the French Mediterranean.

PubMed

Cresson, Pierre; Bouchoucha, Marc; Morat, Fabien; Miralles, Francoise; Chavanon, Fabienne; Loizeau, Veronique; Cossa, Daniel

2015-11-01

Chemical contamination levels and stable isotope ratios provide integrated information about contaminant exposure, trophic position and also biological and environmental influences on marine organisms. By combining these approaches with otolith shape analyses, the aim of the present study was to document the spatial variability of Hg and PCB contamination of the European hake (Merluccius merluccius) in the French Mediterranean, hypothesizing that local contaminant sources, environmental conditions and biological specificities lead to site-specific contamination patterns. High Hg concentrations discriminated Corsica (average: 1.36 ± 0.80 μg g(-1) dm) from the Gulf of Lions (average values<0.5 μg g(-1) dm), where Rhône River input caused high PCB burdens. CB 153 average concentrations ranged between 4.00 ± 0.64 and 18.39 ± 12.38 ng g(-1) dm in the Gulf of Lions, whatever the sex of the individuals, whereas the highest values in Corsica were 6.75 ± 4.22 ng g(-1) dm. Otolith shape discriminated juveniles and adults, due to their different habitats. The use of combined ecotracers was revealed as a powerful tool to discriminate between fish populations at large and small spatial scale, and to enable understanding of the environmental and biological influences on contamination patterns. Copyright © 2015 Elsevier B.V. All rights reserved.

A minimally invasive methodology based on morphometric parameters for day 2 embryo quality assessment.

PubMed

Molina, Inmaculada; Lázaro-Ibáñez, Elisa; Pertusa, Jose; Debón, Ana; Martínez-Sanchís, Juan Vicente; Pellicer, Antonio

2014-10-01

The risk of multiple pregnancy to maternal-fetal health can be minimized by reducing the number of embryos transferred. New tools for selecting embryos with the highest implantation potential should be developed. The aim of this study was to evaluate the ability of morphological and morphometric variables to predict implantation by analysing images of embryos. This was a retrospective study of 135 embryo photographs from 112 IVF-ICSI cycles carried out between January and March 2011. The embryos were photographed immediately before transfer using Cronus 3 software. Their images were analysed using the public program ImageJ. Significant effects (P < 0.05), and higher discriminant power to predict implantation were observed for the morphometric embryo variables compared with morphological ones. The features for successfully implanted embryos were as follows: four cells on day 2 of development; all blastomeres with circular shape (roundness factor greater than 0.9), an average zona pellucida thickness of 13 µm and an average of 17695.1 µm² for the embryo area. Embryo size, which is described by its area and the average roundness factor for each cell, provides two objective variables to consider when predicting implantation. This approach should be further investigated for its potential ability to improve embryo scoring. Copyright © 2014 Reproductive Healthcare Ltd. Published by Elsevier Ltd. All rights reserved.

47 CFR 15.403 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... between several transmission power levels in the data transmission process. (s) U-NII devices. Intentional... bridge in a peer-to-peer connection or as a connector between the wired and wireless segments of the... the presence of a radar. (c) Average Symbol Envelope Power. The average symbol envelope power is the...

High Performance and Economic Supercapacitors for Energy Storage Based on Carbon Nanomaterials

NASA Astrophysics Data System (ADS)

Samuilov, Vladimir; Farshid, Behzad; Frenkel, Alexander; Sensor CAT at Stony Brook Team

2015-03-01

We designed and manufactured very inexpensive prototypes of supercapacitors for energy storage based on carbon nanomaterials comprised of: reduced graphene oxide (RGOs) and carbon nanotubes (CNTs) as electrodes filled with polymer gel electrolytes. The electrochemical properties of supercapacitors made using these materials were compared and analyzed. A significant tradeoff between the energy density and the power density was determined; RGO electrodes demonstrated the highest energy density, while composite RGO/CNT electrodes showed the highest power density. The thickness of the RGO electrode was varied to determine its effect on the power density of the supercapacitor and results showed that with decreasing electrode thickness power density would increase. The specific capacitances of over 600 F/g were observed.

Protection of Hardware: Powering Systems (Power Converter, Normal Conducting, and Superconducting Magnets)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pfeffer, H.; Flora, B.; Wolff, D.

2016-01-01

Along with the protection of magnets and power converters, we have added a section on personnel protection because this is our highest priority in the design and operation of power systems. Thus, our topics are the protection of people, power converters, and magnet loads (protected from the powering equipment), including normal conducting magnets and superconducting magnets.

The capacity credit of grid-connected photovoltaic systems

NASA Astrophysics Data System (ADS)

Alsema, E. A.; van Wijk, A. J. M.; Turkenburg, W. C.

The capacity credit due photovoltaic (PV) power plants if integrated into the Netherlands grid was investigated, together with an estimate of the total allowable penetration. An hourly simulation was performed based on meteorological data from five stations and considering tilted surfaces, the current grid load pattern, and the load pattern after PV-power augmentation. The reliability of the grid was assessed in terms of a loss of load probability analysis, assuming power drops were limited to 1 GW. A projected tolerance for 2.5 GW of PV power was calculated. Peak demands were determined to be highest in winter, contrary to highest insolation levels; however, daily insolation levels coincided with daily peak demands. Combining the PV input with an equal amount of wind turbine power production was found to augment the capacity credit for both at aggregate outputs of 2-4 GW.

Environmental impact efficiency of natural gas combined cycle power plants: A combined life cycle assessment and dynamic data envelopment analysis approach.

PubMed

Martín-Gamboa, Mario; Iribarren, Diego; Dufour, Javier

2018-02-15

The energy sector is still dominated by the use of fossil resources. In particular, natural gas represents the third most consumed resource, being a significant source of electricity in many countries. Since electricity production in natural gas combined cycle (NGCC) plants provides some benefits with respect to other non-renewable technologies, it is often seen as a transitional solution towards a future low‑carbon power generation system. However, given the environmental profile and operational variability of NGCC power plants, their eco-efficiency assessment is required. In this respect, this article uses a novel combined Life Cycle Assessment (LCA) and dynamic Data Envelopment Analysis (DEA) approach in order to estimate -over the period 2010-2015- the environmental impact efficiencies of 20 NGCC power plants located in Spain. A three-step LCA+DEA method is applied, which involves data acquisition, calculation of environmental impacts through LCA, and the novel estimation of environmental impact efficiency (overall- and term-efficiency scores) through dynamic DEA. Although only 1 out of 20 NGCC power plants is found to be environmentally efficient, all plants show a relatively good environmental performance with overall eco-efficiency scores above 60%. Regarding individual periods, 2011 was -on average- the year with the highest environmental impact efficiency (95%), accounting for 5 efficient NGCC plants. In this respect, a link between high number of operating hours and high environmental impact efficiency is observed. Finally, preliminary environmental benchmarks are presented as an additional outcome in order to further support decision-makers in the path towards eco-efficiency in NGCC power plants. Copyright © 2017 Elsevier B.V. All rights reserved.

Validity and reliability of the Hawaii anaerobic run test.

PubMed

Kimura, Iris F; Stickley, Christopher D; Lentz, Melissa A; Wages, Jennifer J; Yanagi, Kazuhiko; Hetzler, Ronald K

2014-05-01

This study examined the reliability and validity of the Hawaii anaerobic run test (HART) by comparing anaerobic capacity measures obtained to those during the Wingate Anaerobic Test (WAnT). Ninety-six healthy physically active volunteers (age, 22.0 ± 2.8 years; height, 163.9 ± 9.5 cm; body mass, 70.6 ± 14.7 kg; body fat %, 19.29 ± 5.39%) participated in this study. Each participant performed 2 anaerobic capacity tests: the WAnT and the HART by random assignment on separate days. The reliability of the HART was calculated from 2 separate trials of the test and then determined through intraclass correlation coefficients (ICCs). Blood samples were collected, and lactate was analyzed both pretest and posttest for each of the 2 exercise modes. Heart rate and rate of perceived exertion were also measured pre- and post-exercise. Hawaii anaerobic run test peak and mean momentum were calculated as body mass times highest or average split velocity, respectively. Intraclass correlation coefficients between trials of the HART for peak and mean momentum were 0.98 and 0.99, respectively (SEM = 18.8 and 25.7, respectively). Validity of the HART was established through comparison of momentum on the HART with power on the WAnT. High correlations were found between peak power and peak momentum (r = 0.88), as well as mean power and mean momentum (r = 0.94). The HART was considered to be a reliable test of anaerobic power. The HART was also determined to be a valid test of anaerobic power when compared with the WAnT. When testing healthy college-aged individuals, the HART offers an easy and inexpensive alternative maximal effort anaerobic power test to other established tests.

Single-mode single-frequency high peak power all-fiber MOPA at 1550 nm

NASA Astrophysics Data System (ADS)

Kotov, L. V.; Likhachev, M. E.; Bubnov, M. M.; Paramonov, V. M.; Belovolov, M. I.; Lipatov, D. S.; Guryanov, A. N.

2014-10-01

In this Report, we present a record-high-peak-power single-frequency master oscillator power amplifier (MOPA) system based on a newly developed double-clad large-mode-area Yb-free Er-doped fiber (DC-LMA-EDF). A fiber Bragg grating wavelength-stabilized fiber-coupled diode laser at λ=1551 nm with ~2 MHz spectral width was used as the master oscillator. Its radiation was externally modulated with a 5 kHz repetition rate and 92 ns pulse duration and then amplified in a core-pumped Er-doped fiber amplifier up to an average power of 4 mW. The amplified spontaneous emission (ASE) generated at the last preamplifier stage was suppressed by a narrow-band (0.7 nm) DWDM filter. The last MOPA stage was based on the recently developed single-mode DC-LMA-EDF with a mode field diameter of 25 microns and pump clad-absorption of 3 dB/m at λ=980 nm. The pump and the signal were launched into this fiber through a commercial pump combiner in a co-propagating amplifier scheme. At first, we used a 3-m long DC-LMAEDF. In such configuration, a peak power of 800 W was achieved at the output of the amplifier together with a ~ 12 % pump conversion slope efficiency. Further power scaling was limited by SBS. After that we shortened the fiber length to 1 m. As a result, owing to large unabsorbed pump power, the efficiency decreased to ~5 %. However, a peak power of more than 3.5 kW was obtained before the SBS threshold. In this case, the pulse shape changed and its duration decreased to ~60 ns owing to inversion depletion after propagation of the forward front of the pulse. To the best of our knowledge, the peak power of more than 3.5 kW reported here is the highest value ever published for a single-frequency single-mode silica-based fiber laser system operating near λ=1550 nm.

From Supercomputer Modeling to Highest Mass Resolution in FT-ICR.

PubMed

N Nikolaev, Evgene; N Vladimirov, Gleb; Jertz, Roland; Baykut, Gökhan

2013-01-01

Understanding of behavior of ion ensembles inside FT-ICR cell based on the computer simulation of ion motion gives rise to the new ideas of cell designs. The recently introduced novel FT-ICR cell based on a Penning ion trap with specially shaped excitation and detection electrodes prevents distortion of ion cyclotron motion phases (normally caused by non-ideal electric trapping fields) by averaging the trapping DC electric field during the ion motion in the ICR cell. Detection times of 5 min resulting in resolving power close to 40,000,000 have been reached for reserpine at m/z 609 at a magnetic field of only 7 Tesla. Fine structures of resolved 13Cn isotopic cluster groups could be measured for molecular masses up to 5.7 kDa (insulin) with resolving power of 4,000,000 at 7 Tesla. Based on resolved fine structure patterns atomic compositions can be directly determined using a new developed algorithm for fine structure processing. Mass spectra of proteins and multimers of proteins reaching masses up to 186 kDa (enolase tetramer) could be measured with isotopic resolution. For instance, at 7 Tesla resolving power of 800,000 was achieved for enolase dimer (96 kDa) and 500,000 for molecular masses above 100 kDa. Experimental data indicate that there is practically no limit for the resolving power of this ICR cell except by collisional damping in the ultrahigh vacuum chamber.

Conceptual design of a 10 to the 8th power bit magnetic bubble domain mass storage unit and fabrication, test and delivery of a feasibility model

NASA Technical Reports Server (NTRS)

1972-01-01

The conceptual design of a highly reliable 10 to the 8th power-bit bubble domain memory for the space program is described. The memory has random access to blocks of closed-loop shift registers, and utilizes self-contained bubble domain chips with on-chip decoding. Trade-off studies show that the highest reliability and lowest power dissipation is obtained when the memory is organized on a bit-per-chip basis. The final design has 800 bits/register, 128 registers/chip, 16 chips/plane, and 112 planes, of which only seven are activated at a time. A word has 64 data bits +32 checkbits, used in a 16-adjacent code to provide correction of any combination of errors in one plane. 100 KHz maximum rotational frequency keeps power low (equal to or less than, 25 watts) and also allows asynchronous operation. Data rate is 6.4 megabits/sec, access time is 200 msec to an 800-word block and an additional 4 msec (average) to a word. The fabrication and operation are also described for a 64-bit bubble domain memory chip designed to test the concept of on-chip magnetic decoding. Access to one of the chip's four shift registers for the read, write, and clear functions is by means of bubble domain decoders utilizing the interaction between a conductor line and a bubble.

Nitrates, chlorates and trihalomethanes in swimming pool water.

PubMed Central

Beech, J A; Diaz, R; Ordaz, C; Palomeque, B

1980-01-01

Water from swimming pools in the Miami area was analyzed for nitrates, chlorates and trihalomethanes. The average concentrations of nitrate and chlorate found in freshwater pools were 8.6 mg/liter and 16 mg/liter respectively, with the highest concentrations being 54.9 mg/liter and 124 mg/liter, respectively. The average concentration of total trihalomethanes found in freshwater pools was 125 micrograms/liter (mainly chloroform) and in saline pools was 657 micrograms/liter (mainly bromoform); the highest concentration was 430 micrograms/liter (freshwater) and 1287 micrograms/liter (saltwater). The possible public health significance of these results is briefly discussed. PMID:7350831

An Approach to Average Modeling and Simulation of Switch-Mode Systems

ERIC Educational Resources Information Center

Abramovitz, A.

2011-01-01

This paper suggests a pedagogical approach to teaching the subject of average modeling of PWM switch-mode power electronics systems through simulation by general-purpose electronic circuit simulators. The paper discusses the derivation of PSPICE/ORCAD-compatible average models of the switch-mode power stages, their software implementation, and…

18 CFR 301.5 - Changes in Average System Cost methodology.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 18 Conservation of Power and Water Resources 1 2012-04-01 2012-04-01 false Changes in Average System Cost methodology. 301.5 Section 301.5 Conservation of Power and Water Resources FEDERAL ENERGY... ACT § 301.5 Changes in Average System Cost methodology. (a) The Administrator, at his or her...

18 CFR 301.5 - Changes in Average System Cost methodology.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 18 Conservation of Power and Water Resources 1 2014-04-01 2014-04-01 false Changes in Average System Cost methodology. 301.5 Section 301.5 Conservation of Power and Water Resources FEDERAL ENERGY... ACT § 301.5 Changes in Average System Cost methodology. (a) The Administrator, at his or her...

18 CFR 301.5 - Changes in Average System Cost methodology.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 18 Conservation of Power and Water Resources 1 2013-04-01 2013-04-01 false Changes in Average System Cost methodology. 301.5 Section 301.5 Conservation of Power and Water Resources FEDERAL ENERGY... ACT § 301.5 Changes in Average System Cost methodology. (a) The Administrator, at his or her...

18 CFR 301.5 - Changes in Average System Cost methodology.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 18 Conservation of Power and Water Resources 1 2011-04-01 2011-04-01 false Changes in Average System Cost methodology. 301.5 Section 301.5 Conservation of Power and Water Resources FEDERAL ENERGY... ACT § 301.5 Changes in Average System Cost methodology. (a) The Administrator, at his or her...

Synoptic observations of Jupiter's radio emissions: Average Statistical properties observed by Voyager

NASA Technical Reports Server (NTRS)

Alexander, J. K.; Carr, T. D.; Thieman, J. R.; Schauble, J. J.; Riddle, A. C.

1980-01-01

Observations of Jupiter's low frequency radio emissions collected over one month intervals before and after each Voyager encounter were analyzed. Compilations of occurrence probability, average power flux density and average sense of circular polarization are presented as a function of central meridian longitude, phase of Io, and frequency. The results are compared with ground based observations. The necessary geometrical conditions are preferred polarization sense for Io-related decametric emission observed by Voyager from above both the dayside and nightside hemispheres are found to be essentially the same as are observed in Earth based studies. On the other hand, there is a clear local time dependence in the Io-independent decametric emission. Io appears to have an influence on average flux density of the emission down to below 2 MHz. The average power flux density spectrum of Jupiter's emission has a broad peak near 9MHz. Integration of the average spectrum over all frequencies gives a total radiated power for an isotropic source of 4 x 10 to the 11th power W.

Resting state cortical oscillations of patients with Parkinson disease and with and without subthalamic deep brain stimulation: a magnetoencephalography study.

PubMed

Cao, Chunyan; Li, Dianyou; Jiang, Tianxiao; Ince, Nuri Firat; Zhan, Shikun; Zhang, Jing; Sha, Zhiyi; Sun, Bomin

2015-04-01

In this study, we investigate the modification to cortical oscillations of patients with Parkinson disease (PD) by subthalamic deep brain stimulation (STN-DBS). Spontaneous cortical oscillations of patients with PD were recorded with magnetoencephalography during on and off subthalamic nucleus deep brain stimulation states. Several features such as average frequency, average power, and relative subband power in regions of interest were extracted in the frequency domain, and these features were correlated with Unified Parkinson Disease Rating Scale III evaluation. The same features were also investigated in patients with PD without surgery and healthy controls. Patients with Parkinson disease without surgery compared with healthy controls had a significantly lower average frequency and an increased average power in 1 to 48 Hz range in whole cortex. Higher relative power in theta and simultaneous decrease in beta and gamma over temporal and occipital were also observed in patients with PD. The Unified Parkinson Disease Rating Scale III rigidity score correlated with the average frequency and with the relative power of beta and gamma in frontal areas. During subthalamic nucleus deep brain stimulation, the average frequency increased significantly when stimulation was on compared with off state. In addition, the relative power dropped in delta, whereas it rose in beta over the whole cortex. Through the course of stimulation, the Unified Parkinson Disease Rating Scale III rigidity and tremor scores correlated with the relative power of alpha over left parietal. Subthalamic nucleus deep brain stimulation improves the symptoms of PD by suppressing the synchronization of alpha rhythm in somatomotor region.

The metabolic power and energetic demands of elite Gaelic football match play.

PubMed

Malone, Shane; Solan, Barry; Collins, Kieran; Doran, Dominic

2017-05-01

Metabolic power has not yet been investigated within elite Gaelic football. The aim of the current investigation was to compare the metabolic power demands between positional groups and examine the temporal profile of elite Gaelic football match play. Global positional satellite system (GPS) data were collected from 50 elite Gaelic football players from 4 inter-county teams during 35 elite competitive matches over a three season period. A total of 351 complete match samples were obtained for final analysis. Players were categorized based on positional groups; full-back, half-back, midfield, half-forward and full-forward. Instantaneous raw velocity data was obtained from the GPS and exported to a customized spreadsheet which provided estimations of both speed based, derived metabolic power and energy expenditure variables (total distance, high speed distance, average metabolic power, high power distance and total energy expenditure). Match mean distance was 9222±1588 m, reflective of an average metabolic power of 9.5-12.5 W·kg-1, with an average energy expenditure of 58-70 Kj·kg-1 depending on position. There were significant differences between positional groups for both speed-based and metabolic power indices. Midfielders covered more total and high-speed distance, as well as greater average and overall energy expenditure compared to other positions (P<0.001). A reduction in total, high-speed, and high-power distance, as well as average metabolic power throughout the match (P<0.001) was observed. Positional differences exist for both metabolic power and traditional running based variables. The middle three positions (midfield, half-back and half-forward) possess greater activity profiles when compared to other positional groups. The reduction in metabolic power and traditional running based variables are comparable across match play. The current study demonstrates that metabolic power may contribute to our understanding of Gaelic football match-play.

[Trends in mortality by assault in women in selected countries of Latin America, 2001-2011].

PubMed

Molinatti, Florencia; Acosta, Laura Débora

2015-05-01

Describe the trend in deaths by assault in women in Argentina, Brazil, Chile, Colombia, and Mexico between 2001 and 2011. Descriptive study. Mortality from assaults and undetermined intentional acts was calculated, adjusted for age, using the direct method and the World Health Organization's standard population. Joinpoint regression models were used to identify statistically significant changes. The male:female mortality ratio was compared and trends in the rates were calculated and adjusted for each of the two causes of death and the specific rates of mortality by assault in women by age group. The highest rates of assault of women were reported in Brazil, followed by Colombia, Mexico, Argentina, and Chile. Between 2001 and 2011, decreases were reported from Argentina and Colombia; in Brazil and Mexico the rates increased; and in Chile they remained stable. The highest specific rates were found in young women (15-29 years) and adults (30-44 and 45-59 years). In Colombia the rates declined in all groups, while in Mexico they increased in women aged 15 to 59 years. Only Colombia showed a decrease in mortality from undetermined intentional acts; in Argentina and Mexico there was a decrease at the beginning of the period with a later increase; in Brazil no variations were observed. Mortality from assaults on women in Brazil, Colombia, and Mexico between 2001 and 2011 was higher than the world average and the Latin American average; rates were lower in Argentina and Chile, with minor differences between the sexes. Progress must be made in terms of understanding the power relationships that underlie femicide, which should be included in national criminal legislation.

Greenhouse gas emissions of different waste treatment options for sector-specific commercial and industrial waste in Germany.

PubMed

Helftewes, Markus; Flamme, Sabine; Nelles, Michael

2012-04-01

This article investigates greenhouse gas (GHG) emissions from commercial and industrial (C&I) waste treatment considering five sector-specific waste compositions and four different treatment scenarios in Germany. Results show that the highest share of CO₂-equivalent emissions can be avoided in each of the analysed industrial sectors if solid recovered fuel (SRF) is produced for co-incineration in cement kilns. Across all industries, emissions of approximately 680 kg CO₂-eq. Mg⁻¹ C&I waste can be avoided on average under this scenario. The combustion of C&I waste in waste incineration plants without any previous mechanical treatment generates the lowest potential to avoid GHG emissions with a value of approximately 50 kg CO₂-eq. Mg⁻¹ C&I waste on average in all industries. If recyclables are sorted, this can save emissions of approximately 280 kg CO₂-eq. Mg⁻¹ C&I waste while the treatment in SRF power plants amounts to savings of approximately 210 kg CO₂-eq. Mg⁻¹ C&I waste. A comparison of the treatment scenarios of the waste from these five sectors shows that waste treatment of the craft sector leads to the lowest CO₂-equivalent reduction rates of all scenarios. In contrast, the treatment of waste from catering sector leads to the highest CO₂-equivalent reduction rates except for direct incineration in waste incineration plants. The sensitivity analysis of the different scenarios for this paper shows that the efficiency and the substitution factor of energy have a relevant influence on the result. Changes in the substitution factor of 10% can result in changes in emissions of approximately 55 to 75 kg CO₂-eq. Mg⁻¹ in waste incineration plants and approximately 90 kg CO₂-eq. Mg⁻¹ in the case of cement kilns.

Extreme Winds in the Pampa del Castillo Plateau, Patagonia, Argentina, with Reference to Wind Farm Settlement.

NASA Astrophysics Data System (ADS)

Labraga, Juan C.

1994-01-01

Wind farm settlement in Argentina is likely to be initiated in the extended and uniform Pampa del Castillo tablelands (5100 km2) in central cast Patagonia, due to its suitable wind regime and local economic factors. The magnitude of these investments requires not only a detailed wind energy assessment and optimum site selection but also a comprehensive evaluation of the extreme winds experienced in the region.Statistical results, with emphasis on severe winds, of two regional programs of one-year observations at four levels above the ground are presented in this paper. The highest frequencies of hourly mean wind velocities above 40, 60, and 80 km h1 are observed during November and December. The spring power spectrum shows a considerable amount of energy in components with a periodicity ranging from 2.5 to 4 days. Severe wind episodes are usually related to the displacement of low pressure systems from the Atlantic to the Pacific Ocean through the Drake Passage with a periodicity consistent with spectral results. The highest hourly mean wind speed registered in each experimental period (at 60 m AGL) is about 25 m s1. The estimated modal value of the theoretical probability distribution of annual extreme values is in good agreement with observed values. The annual peak gust for an averaging time of 240 s is about 27 m s. The gust factor was computed for different averaging intervals and compared with empirical formulations. Its variation with height and time of year was also analyzed. The general form of the vertical wind profile and its dependence on stability conditions was characterized and compared with that of typical episodes of severe winds.

Development of microsatellite loci exhibiting reverse ascertainment bias and a sexing marker for use in Emperor Geese (Chen canagica)

USGS Publications Warehouse

Gravley, Megan C.; Sage, George K.; Schmutz, Joel A.; Talbot, Sandra L.

2017-01-01

The Alaskan population of Emperor Geese (Chen canagica) nests on the Yukon–Kuskokwim Delta in western Alaska. Numbers of Emperor Geese in Alaska declined from the 1960s to the mid-1980s and since then, their numbers have slowly increased. Low statistical power of microsatellite loci developed in other waterfowl species and used in previous studies of Emperor Geese are unable to confidently assign individual identity. Microsatellite loci for Emperor Goose were therefore developed using shotgun amplification and next-generation sequencing technology. Forty-one microsatellite loci were screened and 14 were found to be polymorphic in Emperor Geese. Only six markers – a combination of four novel loci and two loci developed in other waterfowl species – are needed to identify an individual from among the Alaskan Emperor Goose population. Genetic markers for identifying sex in Emperor Geese were also developed. The 14 novel variable loci and 15 monomorphic loci were screened for polymorphism in four other Arctic-nesting goose species, Black Brant (Branta bernicla nigricans), Greater White-fronted (Anser albifrons), Canada (B. canadensis) and Cackling (B. hutchinsii) Goose. Emperor Goose exhibited the smallest average number of alleles (3.3) and the lowest expected heterozygosity (0.467). Greater White-fronted Geese exhibited the highest average number of alleles (4.7) and Cackling Geese the highest expected heterozygosity (0.599). Six of the monomorphic loci were variable and able to be characterised in the other goose species assayed, a predicted outcome of reverse ascertainment bias. These findings fail to support the hypothesis of ascertainment bias due to selection of microsatellite markers.

Improvement of two-photon microscopic imaging in deep regions of living mouse brains by utilizing a light source based on an electrically controllable gain-switched laser diode

NASA Astrophysics Data System (ADS)

Sawada, Kazuaki; Kawakami, Ryosuke; Fang, Yi-Cheng; Hung, Jui-Hung; Kozawa, Yuichi; Otomo, Kohei; Sato, Shunichi; Yokoyama, Hiroyuki; Nemoto, Tomomi

2018-02-01

In vivo two-photon microscopy is an advantageous technique for observing living mouse brains at high spatial resolutions. We previously used a 1064 nm high-power light source based on an electrically controllable gain-switched laser diode (maximum power: 4 W, repetition rate: 10 MHz, pulse width: 7.5 picoseconds) and successfully visualized EYFP expressing neurons at deeper regions in H-line mouse brains under living conditions. However, severe damages were frequently observed when the laser power after the objective lens was over 600 mW, suggesting that a higher average power might not be suitable for visualizing neural structures and functions at deep regions. To increase fluorescent signals as a strategy to avoid such invasions, here, we evaluated the effects of the excitation laser parameters such as the repetition rate (5 - 10 MHz), or the peak power, at the moderate average powers (10 - 500 mW), by taking the advantage that this electrically controllable light source could be used to change the repetition rate independently from the average power or the pulse width. The fluorescent signals of EYFP at layer V of the cerebral cortex were increased by approximately twofold when the repetition rate was decreased from 10 MHz to 5 MHz at the same average power. We also confirmed similar effects in the EYFP solution (335 μM) and fixed brain slices. These results suggest that in vivo two-photon microscopic imaging might be improved by increasing the peak power at the same average power while avoiding the severe damages in living brains.

Effect of the Low-Temperature Annealing on Zn-Doped Indium-Tin-Oxide Films for Silicon Heterojunction Solar Cells

NASA Astrophysics Data System (ADS)

Lee, Seunghun; Lee, Jong-Han; Tark, Sung Ju; Choi, Suyoung; Kim, Chan Seok; Lee, Jeong Chul; Kim, Won Mok; Kim, Donghwan

2012-10-01

The effects of the low-temperature annealing on Zn-doped indium-tin-oxide (ITO) films such as the electrical, optical and structural properties were investigated. Zn-doped ITO films were fabricated by rf magnetron sputtering of ITO and Al-doped ZnO (AZO) targets on corning glass at room temperature. The content of Zn increased with increasing the power of AZO target. The carrier concentration of films shows the decreasing behaviour with increasing the content of Zn, due to a carrier compensation originating from the substitution of a doped Zn for an In or interstitial site. After the low-temperature annealing at 180 °C in vacuum, all films were slightly decreased a carrier concentration and increased the hall mobility because of the absorption of oxygen on the surface films. In addition, the average transmittance did not show a considerable change and had a high values over 80%. Especially, the Zn-doped ITO with atomic ratio of Zn/(In+Zn) of 6.8 at. % had the resistivity of 4×10-4 Ω cm, the highest hall mobility of 41 cm2 V-1 s-1, and the average transmittance of 82%.

Foreign exchange market data analysis reveals statistical features that predict price movement acceleration.

PubMed

Nacher, Jose C; Ochiai, Tomoshiro

2012-05-01

Increasingly accessible financial data allow researchers to infer market-dynamics-based laws and to propose models that are able to reproduce them. In recent years, several stylized facts have been uncovered. Here we perform an extensive analysis of foreign exchange data that leads to the unveiling of a statistical financial law. First, our findings show that, on average, volatility increases more when the price exceeds the highest (or lowest) value, i.e., breaks the resistance line. We call this the breaking-acceleration effect. Second, our results show that the probability P(T) to break the resistance line in the past time T follows power law in both real data and theoretically simulated data. However, the probability calculated using real data is rather lower than the one obtained using a traditional Black-Scholes (BS) model. Taken together, the present analysis characterizes a different stylized fact of financial markets and shows that the market exceeds a past (historical) extreme price fewer times than expected by the BS model (the resistance effect). However, when the market does, we predict that the average volatility at that time point will be much higher. These findings indicate that any Markovian model does not faithfully capture the market dynamics.

Foreign exchange market data analysis reveals statistical features that predict price movement acceleration

NASA Astrophysics Data System (ADS)

Nacher, Jose C.; Ochiai, Tomoshiro

2012-05-01

Increasingly accessible financial data allow researchers to infer market-dynamics-based laws and to propose models that are able to reproduce them. In recent years, several stylized facts have been uncovered. Here we perform an extensive analysis of foreign exchange data that leads to the unveiling of a statistical financial law. First, our findings show that, on average, volatility increases more when the price exceeds the highest (or lowest) value, i.e., breaks the resistance line. We call this the breaking-acceleration effect. Second, our results show that the probability P(T) to break the resistance line in the past time T follows power law in both real data and theoretically simulated data. However, the probability calculated using real data is rather lower than the one obtained using a traditional Black-Scholes (BS) model. Taken together, the present analysis characterizes a different stylized fact of financial markets and shows that the market exceeds a past (historical) extreme price fewer times than expected by the BS model (the resistance effect). However, when the market does, we predict that the average volatility at that time point will be much higher. These findings indicate that any Markovian model does not faithfully capture the market dynamics.

Upper-Bound Radiation Dose Assessment for Military Personnel at McMurdo Station, Antarctica, between 1962 and 1979, Revision 1

DTIC Science & Technology

2016-07-29

using Equation 2 (DTRA, 2010, ED01): Dmonitor highest average HT TLD D = (2) where: TLDhighest = Highest TLD measurement during environmental...the processing of administrative claims or litigation. For use by Agency officials, employees, and authorized contractors . ROUTINE USES

Theoretical study of enhancing the piezoelectric nanogenerator's output power by optimizing the external force's shape

NASA Astrophysics Data System (ADS)

Xu, Qi; Qin, Yong

2017-07-01

The average power is one of the key parameters of piezoelectric nanogenerators (PENGs). In this paper, we demonstrate that the PENG's output can be gigantically improved by choosing driving force with an appropriate shape. When the load resistance is 100 MΩ and the driven forces have a magnitude of 19.6 nN, frequency of 10 Hz, the average power of PENG driven by square shaped force is six orders of magnitude higher than that driven by triangular shaped and sinusoidal shaped forces. These results are of importance for optimizing the average power of the PENGs in practical applications.

High average power scaleable thin-disk laser

DOEpatents

Beach, Raymond J.; Honea, Eric C.; Bibeau, Camille; Payne, Stephen A.; Powell, Howard; Krupke, William F.; Sutton, Steven B.

2002-01-01

Using a thin disk laser gain element with an undoped cap layer enables the scaling of lasers to extremely high average output power values. Ordinarily, the power scaling of such thin disk lasers is limited by the deleterious effects of amplified spontaneous emission. By using an undoped cap layer diffusion bonded to the thin disk, the onset of amplified spontaneous emission does not occur as readily as if no cap layer is used, and much larger transverse thin disks can be effectively used as laser gain elements. This invention can be used as a high average power laser for material processing applications as well as for weapon and air defense applications.

Pilot study for quantifying driving characteristics during power wheelchair soccer.

PubMed

Kumar, Amit; Karmarkar, Amol M; Collins, Diane M; Souza, Ana; Oyster, Michelle L; Cooper, Rosemarie; Cooper, Rory A

2012-01-01

This study determined the driving characteristics of wheelchair users during power wheelchair soccer games. Data for this study were collected at the 28th and 29th National Veterans Wheelchair Games. Nineteen veterans who were 18 years or older and power wheelchair soccer players completed a brief demographic survey and provided information about their power wheelchairs. A customized data-logging device was placed on each participant's wheelchair before power soccer game participation. The data logger was removed at the end of the final game for each participant. The average distance traveled during the games was 899.5 +/- 592.5 m, and the average maximum continuous distance traveled was 256.0 +/- 209.4 m. The average wheelchair speed was 0.8 +/- 0.2 m/s, and the average duration of driving time was 17.6 +/- 8.3 min. Average proportion of time spent at a speed >1 m/s was 30.7% +/- 33.8%, between 0.5 and 1 m/s was 16.2% +/- 34.4%, and <0.5 m/s was 21.4% +/- 24.3%. The information from this descriptive study provides insight for future research in the field of adapted sports for people with high levels of impairments who use power wheelchairs for their mobility.

Econophysics of adaptive power markets: When a market does not dampen fluctuations but amplifies them

NASA Astrophysics Data System (ADS)

Krause, Sebastian M.; Börries, Stefan; Bornholdt, Stefan

2015-07-01

The average economic agent is often used to model the dynamics of simple markets, based on the assumption that the dynamics of a system of many agents can be averaged over in time and space. A popular idea that is based on this seemingly intuitive notion is to dampen electric power fluctuations from fluctuating sources (as, e.g., wind or solar) via a market mechanism, namely by variable power prices that adapt demand to supply. The standard model of an average economic agent predicts that fluctuations are reduced by such an adaptive pricing mechanism. However, the underlying assumption that the actions of all agents average out on the time axis is not always true in a market of many agents. We numerically study an econophysics agent model of an adaptive power market that does not assume averaging a priori. We find that when agents are exposed to source noise via correlated price fluctuations (as adaptive pricing schemes suggest), the market may amplify those fluctuations. In particular, small price changes may translate to large load fluctuations through catastrophic consumer synchronization. As a result, an adaptive power market may cause the opposite effect than intended: Power demand fluctuations are not dampened but amplified instead.

Average power scaling of UV excimer lasers drives flat panel display and lidar applications

NASA Astrophysics Data System (ADS)

Herbst, Ludolf; Delmdahl, Ralph F.; Paetzel, Rainer

2012-03-01

Average power scaling of 308nm excimer lasers has followed an evolutionary path over the last two decades driven by diverse industrial UV laser microprocessing markets. Recently, a new dual-oscillator and beam management concept for high-average power upscaling of excimer lasers has been realized, for the first time enabling as much as 1.2kW of stabilized UV-laser average output power at a UV wavelength of 308nm. The new dual-oscillator concept enables low temperature polysilicon (LTPS) fabrication to be extended to generation six glass substrates. This is essential in terms of a more economic high-volume manufacturing of flat panel displays for the soaring smartphone and tablet PC markets. Similarly, the cost-effective production of flexible displays is driven by 308nm excimer laser power scaling. Flexible displays have enormous commercial potential and can largely use the same production equipment as is used for rigid display manufacturing. Moreover, higher average output power of 308nm excimer lasers aids reducing measurement time and improving the signal-to-noise ratio in the worldwide network of high altitude Raman lidar stations. The availability of kW-class 308nm excimer lasers has the potential to take LIDAR backscattering signal strength and achievable altitude to new levels.

High sustained average power cw and ultrafast Yb:YAG near-diffraction-limited cryogenic solid-state laser.

PubMed

Brown, David C; Singley, Joseph M; Kowalewski, Katie; Guelzow, James; Vitali, Victoria

2010-11-22

We report what we believe to be record performance for a high average power Yb:YAG cryogenic laser system with sustained output power. In a CW oscillator-single-pass amplifier configuration, 963 W of output power was measured. In a second configuration, a two amplifier Yb:YAG cryogenic system was driven with a fiber laser picosecond ultrafast oscillator at a 50 MHz repetition rate, double-passed through the first amplifier and single-passed through the second, resulting in 758 W of average power output. Pulses exiting the system have a FWHM pulsewidth of 12.4 ps, an energy/pulse of 15.2 μJ, and a peak power of 1.23 MW. Both systems are force convection-cooled with liquid nitrogen and have been demonstrated to run reliably over long time periods.

Development of high-average-power DPSSL with high beam quality

NASA Astrophysics Data System (ADS)

Nakai, Sadao; Kanabe, Tadashi; Kawashima, Toshiyuki; Yamanaka, Masanobu; Izawa, Yasukazu; Nakatuka, Masahiro; Kandasamy, Ranganathan; Kan, Hirofumi; Hiruma, Teruo; Niino, Masayuki

2000-08-01

The recent progress of high power diode laser is opening new fields of laser and its application. We are developing high average power diode pumped solid state laser DPSSL for laser fusion power plant, for space propulsion and for various applications in industry. The common features or requirements of our High Average-power Laser for Nuclear-fusion Application (HALNA) are large pulse energy with relatively low repetition of few tens Hz, good beam quality of order of diffraction limit and high efficiency more than 10%. We constructed HALNA 10 (10J X 10 Hz) and tested the performance to clarify the scalability to higher power system. We have obtained in a preliminary experiment a 8.5 J output energy at 0.5 Hz with beam quality of 2 times diffraction limited far-field pattern.

Trends in Personal Belief Exemption Rates Among Alternative Private Schools: Waldorf, Montessori, and Holistic Kindergartens in California, 2000–2014

PubMed Central

Bednarczyk, Robert A.; Richards, Jennifer L.; Allen, Kristen E.; Warraich, Gohar J.; Omer, Saad B.

2017-01-01

Objectives. To evaluate trends in rates of personal belief exemptions (PBEs) to immunization requirements for private kindergartens in California that practice alternative educational methods. Methods. We used California Department of Public Health data on kindergarten PBE rates from 2000 to 2014 to compare annual average increases in PBE rates between schools. Results. Alternative schools had an average PBE rate of 8.7%, compared with 2.1% among public schools. Waldorf schools had the highest average PBE rate of 45.1%, which was 19 times higher than in public schools (incidence rate ratio = 19.1; 95% confidence interval = 16.4, 22.2). Montessori and holistic schools had the highest average annual increases in PBE rates, slightly higher than Waldorf schools (Montessori: 8.8%; holistic: 7.1%; Waldorf: 3.6%). Conclusions. Waldorf schools had exceptionally high average PBE rates, and Montessori and holistic schools had higher annual increases in PBE rates. Children in these schools may be at higher risk for spreading vaccine-preventable diseases if trends are not reversed. PMID:27854520

Trends in Personal Belief Exemption Rates Among Alternative Private Schools: Waldorf, Montessori, and Holistic Kindergartens in California, 2000-2014.

PubMed

Brennan, Julia M; Bednarczyk, Robert A; Richards, Jennifer L; Allen, Kristen E; Warraich, Gohar J; Omer, Saad B

2017-01-01

To evaluate trends in rates of personal belief exemptions (PBEs) to immunization requirements for private kindergartens in California that practice alternative educational methods. We used California Department of Public Health data on kindergarten PBE rates from 2000 to 2014 to compare annual average increases in PBE rates between schools. Alternative schools had an average PBE rate of 8.7%, compared with 2.1% among public schools. Waldorf schools had the highest average PBE rate of 45.1%, which was 19 times higher than in public schools (incidence rate ratio = 19.1; 95% confidence interval = 16.4, 22.2). Montessori and holistic schools had the highest average annual increases in PBE rates, slightly higher than Waldorf schools (Montessori: 8.8%; holistic: 7.1%; Waldorf: 3.6%). Waldorf schools had exceptionally high average PBE rates, and Montessori and holistic schools had higher annual increases in PBE rates. Children in these schools may be at higher risk for spreading vaccine-preventable diseases if trends are not reversed.

Measuring radio-signal power accurately

NASA Technical Reports Server (NTRS)

Goldstein, R. M.; Newton, J. W.; Winkelstein, R. A.

1979-01-01

Absolute value of signal power in weak radio signals is determined by computer-aided measurements. Equipment operates by averaging received signal over several-minute period and comparing average value with noise level of receiver previously calibrated.

The hard X-ray continuum of Cen a observed with INTEGRAL SPI

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burke, Mark J.; Jourdain, Elisabeth; Roques, Jean-Pierre

2014-05-20

We revisit the average hard X-ray spectrum from the active galactic nucleus (AGN) of Centaurus A (Cen A) using 10 yr worth of observations with INTEGRAL SPI. This source has the highest flux observed from any AGNs in the SPI bandpass (23 keV-8 MeV). The 10 year light curve of Cen A is presented, and hardness ratios confirm that the spectral shape changes very little despite the luminosity varying by a factor of a few. Primarily, we establish the presence of a reflection component in the average spectrum by demonstrating an excess between 20 and 60 keV, from extending themore » spectral shape observed at low energy to the SPI regime. The excess in Chandra HETGS and INTEGRAL SPI data is well described by reflection of the dominant power-law spectrum from a neutral, optically thick atmosphere. We find that the reprocessed emission contributes 20%-25% of the 23-100 keV flux. The existence of a cutoff at tens to hundreds of kiloelectron volts remains controversial. Using simulated spectra, we demonstrate that a high energy cutoff reproduces the observed spectral properties of Cen A more readily than a simple power law. However, we also show that such a cutoff is probably underestimated when neglecting (even modest) reflection, and for Cen A would be at energies >700 keV, with a confidence of >95%. This is atypically high for thermal Comptonizing plasmas observed in AGNs, and we propose that we are in fact modeling the more gradual change in spectral shape expected of synchrotron self-Compton spectra.« less

[Analysis About Spatial and Temporal Distribution of SO2 and An Ambient SO2 Pollution Process in Beijing During 2000-2014].

PubMed

Cheng, Nian-liang; Zhang, Da-wei; Li, Yun-ting; Chen, Tian; Li, Jin-xiang; Dong, Xin; Sun, Rui-wen; Meng, Fan

2015-11-01

Spatial and temporal distribution of SO2 during 2000-2014 was all analyzed based on the SO2 monitoring data that Beijing Municipal Environmental Monitoring Center released and the formation mechanism of a typical air pollution episode in January 2014 was also investigated by combining numerical model CAM(x). Analysis results showed that mass concentration of ρ(SO2) in Beijing in 2014 decreased 69% compared to that in 2000 with an annual gradient from 2000 to 2014 of - 3.5 μg x (m3 x a)(-1). Monthly average concentration of SO2 changed in a U shape curve and from the lowest to the highest, and seasonal variations of SO2 concentrations were as follows: winter > spring > autumn > summer; concentration of SO2 in heating season was significantly higher than that in non heating season. Annual average concentration of SO2 was lower in northern and western regions while higher in six city area and southern area. Concentrations of SO2 at Shijingshan, Dongsi, Tongzhou monitoring sites were significantly decreased related to SO2 emission reduction measures. During a heavy air pollution process in January 14 - 18th 2014 there was obviously SO2 regional transportation and model simulation analysis based on PAST showed that the contribution of SO2 regional transport to Beijing was 83% with elevated power plants surrounding Beijing accounting for 21% and the four major Beijing power plants contributing about 3.5% to the SO2 concentration during this heavy air pollution process.

22 W average power multiterawatt femtosecond laser chain enabling 1019 W/cm2 at 100 Hz

NASA Astrophysics Data System (ADS)

Clady, R.; Azamoum, Y.; Charmasson, L.; Ferré, A.; Utéza, O.; Sentis, M.

2018-05-01

We measure the wavefront distortions of a high peak power ultrashort (23 fs) laser system under high average power load. After 6 min—100 Hz operation of the laser at full average power (> 22 W after compression), the thermally induced wavefront distortions reach a steady state and the far-field profile of the laser beam no longer changes. By means of a deformable mirror located after the vacuum compressor, we apply a static pre-compensation to correct those aberrations allowing us to demonstrate a dramatic improvement of the far-field profile at 100 Hz with the reduction of the residual wavefront distortions below λ/16 before focusing. The applied technique provides 100 Hz operation of the femtosecond laser chain with stable pulse characteristics, corresponding to peak intensity above 1019 W/cm2 and average power of 19 W on target, which enables the study of relativistic optics at high repetition rate using a moderate f-number focusing optics ( f/4.5).

Power System Mass Analysis for Hydrogen Reduction Oxygen Production on the Lunar Surface

NASA Technical Reports Server (NTRS)

Colozza, Anthony J.

2009-01-01

The production of oxygen from the lunar regolith requires both thermal and electrical power in roughly similar proportions. This unique power requirement is unlike most applications on the lunar surface. To efficiently meet these requirements, both solar PV array and solar concentrator systems were evaluated. The mass of various types of photovoltaic and concentrator based systems were calculated to determine the type of power system that provided the highest specific power. These were compared over a range of oxygen production rates. Also a hybrid type power system was also considered. This system utilized a photovoltaic array to produce the electrical power and a concentrator to provide the thermal power. For a single source system the three systems with the highest specific power were a flexible concentrator/Stirling engine system, a rigid concentrator/Stirling engine system and a tracking triple junction solar array system. These systems had specific power values of 43, 34, and 33 W/kg, respectively. The hybrid power system provided much higher specific power values then the single source systems. The best hybrid combinations were the triple junction solar array with the flexible concentrator and the rigid concentrator. These systems had a specific power of 81 and 68 W/kg, respectively.

Stochastic Growth Theory of Spatially-Averaged Distributions of Langmuir Fields in Earth's Foreshock

NASA Technical Reports Server (NTRS)

Boshuizen, Christopher R.; Cairns, Iver H.; Robinson, P. A.

2001-01-01

Langmuir-like waves in the foreshock of Earth are characteristically bursty and irregular, and are the subject of a number of recent studies. Averaged over the foreshock, it is observed that the probability distribution is power-law P(bar)(log E) in the wave field E with the bar denoting this averaging over position, In this paper it is shown that stochastic growth theory (SGT) can explain a power-law spatially-averaged distributions P(bar)(log E), when the observed power-law variations of the mean and standard deviation of log E with position are combined with the log normal statistics predicted by SGT at each location.

Monitoring of perchlorate in diverse foods and its estimated dietary exposure for Korea populations.

PubMed

Lee, Ji-Woo; Oh, Sung-Hee; Oh, Jeong-Eun

2012-12-01

The perchlorate concentrations in various Korean food samples were monitored, and 663 samples belonging to 39 kinds of food were analyzed. The analysis results revealed that dairy products contain the highest average concentration of 6.34 μg/kg and high detection frequency of over 85%. Fruit and vegetables showed the next highest perchlorate concentration with an average of 6.17 μg/kg. Especially, with its average concentration of 39.9 μg/kg, spinach showed the highest perchlorate level among all target food samples studied. Tomato was followed by spinach, which showed a high perchlorate average concentration of 19.8 μg/kg, and over 7 μg/kg was detected in ham and sausage (avg. 7.31 μg/kg) and in instant noodles (avg. 7.58 μg/kg). Less than 2 μg/kg was detected in fishes, meats and beverages. The exposure dose of perchlorate in Korean by food intake was calculated on the basis of the analyzed perchlorate levels in this study. The daily perchlorate dose to which Korean adults are exposed is 0.04 μg/kg bw/day, which is lower than the RfD (0.7 μg/kg bw/day) value suggested by US NAS. This result indicates that Korean people's current exposure to perchlorate from domestic food consumption is evaluated as safe. Copyright © 2012 Elsevier B.V. All rights reserved.

A PEMS study of the emissions of gaseous pollutants and ultrafine particles from gasoline- and diesel-fueled vehicles

NASA Astrophysics Data System (ADS)

Huang, Cheng; Lou, Diming; Hu, Zhiyuan; Feng, Qian; Chen, Yiran; Chen, Changhong; Tan, Piqiang; Yao, Di

2013-10-01

On-road emission measurements of gasoline- and diesel-fueled vehicles were conducted by a portable emission measurement system (PEMS) in Shanghai, China. Horiba OBS 2200 and TSI EEPS 3090 were employed to detect gaseous and ultrafine particle emissions during the tests. The driving-based emission factors of gaseous pollutants and particle mass and number were obtained on various road types. The average NOx emission factors of the diesel bus, diesel car, and gasoline car were 8.86, 0.68, and 0.17 g km-1, all of which were in excess of their emission limits. The particle number emission factors were 7.06 × 1014, 6.08 × 1014, and 1.57 × 1014 km-1, generally higher than the results for similar vehicle types reported in the previous studies. The size distributions of the particles emitted from the diesel vehicles were mainly concentrated in the accumulation mode, while those emitted from the gasoline car were mainly distributed in the nucleation mode. Both gaseous and particle emission rates exhibit significant correlations with the change in vehicle speed and power demand. The lowest emission rates for each vehicle type were produced during idling. The highest emission rates for each vehicle type were generally found in high-VSP bins. The particle number emission rates of the gasoline car show the strongest growth trend with increasing VSP and speed. The particle number emission for the gasoline car increased by 3 orders of magnitude from idling to the highest VSP and driving speed conditions. High engine power caused by aggressive driving or heavy loads is the main contributor to high emissions for these vehicles in real-world situations.

Simulations of thermal lensing of a Ti:Sapphire crystal end-pumped with high average power

NASA Astrophysics Data System (ADS)

Wagner, Gerd; Shiler, Max; Wulfmeyer, Volker

2005-10-01

A detailed 3-dimensional calculation of the temperature field of a laser crystal pumped with high average power is presented. The pump configuration, the anisotropy of a Brewster-angle-cut Ti:Sapphire crystal, and the temperature dependence of the thermal conductivity are taken into account. The corresponding focal length of the thermal lens is calculated for pump levels up to 100 W. This refined thermal model is the basis for a optimized resonator design of a high-average power differential absorption lidar system transmitter.

Simulations of thermal lensing of a Ti:Sapphire crystal end-pumped with high average power.

PubMed

Wagner, Gerd; Shiler, Max; Wulfmeyer, Volker

2005-10-03

A detailed 3-dimensional calculation of the temperature field of a laser crystal pumped with high average power is presented. The pump configuration, the anisotropy of a Brewster-angle-cut Ti:Sapphire crystal, and the temperature dependence of the thermal conductivity are taken into account. The corresponding focal length of the thermal lens is calculated for pump levels up to 100 W. This refined thermal model is the basis for a optimized resonator design of a high-average power differential absorption lidar system transmitter.

Power tiller: vibration magnitudes and intervention development for vibration reduction.

PubMed

Chaturvedi, Varun; Kumar, Adarsh; Singh, J K

2012-09-01

The operators of power tiller are exposed to a high level of vibration originating from the dynamic interaction between the soil and the machine. The vibration from the power tiller is transmitted from the handle to hands, arms and shoulders. In the present study, experiments were conducted in three operational conditions i.e. transportation on farm roads, tilling with cultivator and rota-tilling with rota-vator. The highest vibration values were observed in x-direction in all the experiments. The maximum vibration rms values for x-direction were 5.96, 6.81 and 8.00 ms(-2) in tilling with cultivator, transportation and rota-tilling respectively. Three materials were used for intervention development to reduce vibration magnitude. The maximum reduction of 25.30, 31.21 and 30.45% in transportation; 23.50, 30.64 and 20.86% in tilling with cultivator and 24.03, 29.18 and 25.52% in rota-tilling were achieved with polyurethane (PU), rubber and combination of PU and rubber intervention. It was found that the maximum vibration reductions were achieved with the rubber in all three operational conditions. The average exposure time for occurrence of white finger syndrome increased by 28-50% with incorporation of intervention in different operations. Physiological and postural parameters also improved with incorporation of interventions. Copyright © 2012 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Enhanced Charge Extraction of Li-Doped TiO₂ for Efficient Thermal-Evaporated Sb₂S₃ Thin Film Solar Cells.

PubMed

Lan, Chunfeng; Luo, Jingting; Lan, Huabin; Fan, Bo; Peng, Huanxin; Zhao, Jun; Sun, Huibin; Zheng, Zhuanghao; Liang, Guangxing; Fan, Ping

2018-02-28

We provided a new method to improve the efficiency of Sb₂S₃ thin film solar cells. The TiO₂ electron transport layers were doped by lithium to improve their charge extraction properties for the thermal-evaporated Sb₂S₃ solar cells. The Mott-Schottky curves suggested a change of energy band and faster charge transport in the Li-doped TiO₂ films. Compared with the undoped TiO₂, Li-doped mesoporous TiO₂ dramatically improved the photo-voltaic performance of the thermal-evaporated Sb₂S₃ thin film solar cells, with the average power conversion efficiency ( PCE ) increasing from 1.79% to 4.03%, as well as the improved open-voltage ( V oc ), short-circuit current ( J sc ) and fill factors. The best device based on Li-doped TiO₂ achieved a power conversion efficiency up to 4.42% as well as a V oc of 0.645 V, which are the highest values among the reported thermal-evaporated Sb₂S₃ solar cells. This study showed that Li-doping on TiO₂ can effectively enhance the charge extraction properties of electron transport layers, offering a new strategy to improve the efficiency of Sb₂S₃-based solar cells.

Population data and mutation rates of 20 autosomal STR loci in a Chinese Han population from Yunnan Province, Southwest China.

PubMed

Zhang, Xiufeng; Liu, Linlin; Xie, Runfang; Wang, Guiyi; Shi, Yuan; Gu, Tao; Hu, Liping; Nie, Shengjie

2018-07-01

The genetic polymorphisms of 20 autosomal short tandem repeat (STR) loci included in the PowerPlex® 21 kit were evaluated from 2068 unrelated, healthy individuals from the Chinese Han population of Yunnan Province in southwest China. All of the loci reached Hardy-Weinberg equilibrium. These loci were examined to determine allele frequencies and forensic statistical parameters. The genetic relationships among the Yunnan Han and other Chinese populations were also estimated. The combined discrimination power and probability of excluding paternity of the 20 STR loci were 0.99999999999999999999999126 and 0.999999975, respectively. In addition, mutation rates from 4363 parentage cases (2215 trios and 2148 duos) were investigated in this study. A total of 164 mutations were observed in 6578 meioses from the 20 loci. The highest mutation rate was observed in D12S391 (0.30%), and the lowest mutation rates were observed in D13S317 (0.03%) and TPOX (0.03%). The average mutation rate for the 20 loci was estimated to be 1.246 × 10 -3 per meiosis. The mutations were primarily single-step and paternal mutations.

Evaluation of performance of select fusion experiments and projected reactors

NASA Technical Reports Server (NTRS)

Miley, G. H.

1978-01-01

The performance of NASA Lewis fusion experiments (SUMMA and Bumpy Torus) is compared with other experiments and that necessary for a power reactor. Key parameters cited are gain (fusion power/input power) and the time average fusion power, both of which may be more significant for real fusion reactors than the commonly used Lawson parameter. The NASA devices are over 10 orders of magnitude below the required powerplant values in both gain and time average power. The best experiments elsewhere are also as much as 4 to 5 orders of magnitude low. However, the NASA experiments compare favorably with other alternate approaches that have received less funding than the mainline experiments. The steady-state character and efficiency of plasma heating are strong advantages of the NASA approach. The problem, though, is to move ahead to experiments of sufficient size to advance in gain and average power parameters.

Parameter optimization for reproducible cardiac 1 H-MR spectroscopy at 3 Tesla.

PubMed

de Heer, Paul; Bizino, Maurice B; Lamb, Hildo J; Webb, Andrew G

2016-11-01

To optimize data acquisition parameters in cardiac proton MR spectroscopy, and to evaluate the intra- and intersession variability in myocardial triglyceride content. Data acquisition parameters at 3 Tesla (T) were optimized and reproducibility measured using, in total, 49 healthy subjects. The signal-to-noise-ratio (SNR) and the variance in metabolite amplitude between averages were measured for: (i) global versus local power optimization; (ii) static magnetic field (B 0 ) shimming performed during free-breathing or within breathholds; (iii) post R-wave peak measurement times between 50 and 900 ms; (iv) without respiratory compensation, with breathholds and with navigator triggering; and (v) frequency selective excitation, Chemical Shift Selective (CHESS) and Multiply Optimized Insensitive Suppression Train (MOIST) water suppression techniques. Using the optimized parameters intra- and intersession myocardial triglyceride content reproducibility was measured. Two cardiac proton spectra were acquired with the same parameters and compared (intrasession reproducibility) after which the subject was removed from the scanner and placed back in the scanner and a third spectrum was acquired which was compared with the first measurement (intersession reproducibility). Local power optimization increased SNR on average by 22% compared with global power optimization (P = 0.0002). The average linewidth was not significantly different for pencil beam B 0 shimming using free-breathing or breathholds (19.1 Hz versus 17.5 Hz; P = 0.15). The highest signal stability occurred at a cardiac trigger delay around 240 ms. The mean amplitude variation was significantly lower for breathholds versus free-breathing (P = 0.03) and for navigator triggering versus free-breathing (P = 0.03) as well as for navigator triggering versus breathhold (P = 0.02). The mean residual water signal using CHESS (1.1%, P = 0.01) or MOIST (0.7%, P = 0.01) water suppression was significantly lower than using frequency selective excitation water suppression (7.0%). Using the optimized parameters an intrasession limits of agreement of the myocardial triglyceride content of -0.11% to +0.04%, and an intersession of -0.15% to +0.9%, were achieved. The coefficient of variation was 5% for the intrasession reproducibility and 6.5% for the intersession reproducibility. Using approaches designed to optimize SNR and minimize the variation in inter-average signal intensities and frequencies/phases, a protocol was developed to perform cardiac MR spectroscopy on a clinical 3T system with high reproducibility. J. Magn. Reson. Imaging 2016;44:1151-1158. © 2016 International Society for Magnetic Resonance in Medicine.

Power Amplifier Module with 734-mW Continuous Wave Output Power

NASA Technical Reports Server (NTRS)

Fung, King Man; Samoska, Lorene A.; Kangaslahti, Pekka P.; Lamgrigtsen, Bjorn H.; Goldsmith, Paul F.; Lin, Robert H.; Soria, Mary M.; Cooperrider, Joelle T.; Micovic, Moroslav; Kurdoghlian, Ara

2010-01-01

Research findings were reported from an investigation of new gallium nitride (GaN) monolithic millimeter-wave integrated circuit (MMIC) power amplifiers (PAs) targeting the highest output power and the highest efficiency for class-A operation in W-band (75-110 GHz). W-band PAs are a major component of many frequency multiplied submillimeter-wave LO signal sources. For spectrometer arrays, substantial W-band power is required due to the passive lossy frequency multipliers-to generate higher frequency signals in nonlinear Schottky diode-based LO sources. By advancing PA technology, the LO system performance can be increased with possible cost reductions compared to current GaAs PAs. High-power, high-efficiency GaN PAs are cross-cutting and can enable more efficient local oscillator distribution systems for new astrophysics and planetary receivers and heterodyne array instruments. It can also allow for a new, electronically scannable solid-state array technology for future Earth science radar instruments and communications platforms.

Mode-locked Yb:YAG thin-disk oscillator with 41 µJ pulse energy at 145 W average infrared power and high power frequency conversion.

PubMed

Bauer, Dominik; Zawischa, Ivo; Sutter, Dirk H; Killi, Alexander; Dekorsy, Thomas

2012-04-23

We demonstrate the generation of 1.1 ps pulses containing more than 41 µJ of energy directly out of an Yb:YAG thin-disk without any additional amplification stages. The laser oscillator operates in ambient atmosphere with a 3.5 MHz repetition rate and 145 W of average output power at a fundamental wavelength of 1030 nm. An average output power of 91.5 W at 515 nm was obtained by frequency doubling with a conversion efficiency exceeding 65%. Third harmonic generation resulted in 34 W at 343 nm at 34% efficiency. © 2012 Optical Society of America

Student Discipline in New Hampshire Schools

ERIC Educational Resources Information Center

Wauchope, Barbara

2009-01-01

A new analysis of student discipline in New Hampshire schools in the 2007-2008 school year shows that out-of-school suspension rates are higher and statewide expulsion rates are lower than the national average. Schools reporting the highest rates of suspensions and expulsions are the smallest in the state and have the highest percentage of…

40 CFR 63.11647 - What are my monitoring requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... temperature limit is the highest temperature measured during any run of the initial compliance test or 10... either the highest reading during the test or at 10 °F higher than the average temperature measured... least 11 days apart from other consecutive tests. The mercury concentration must be maintained below the...

40 CFR 63.11647 - What are my monitoring requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

... temperature limit is the highest temperature measured during any run of the initial compliance test or 10... either the highest reading during the test or at 10 °F higher than the average temperature measured... least 11 days apart from other consecutive tests. The mercury concentration must be maintained below the...

40 CFR 63.11647 - What are my monitoring requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

... temperature limit is the highest temperature measured during any run of the initial compliance test or 10... either the highest reading during the test or at 10 °F higher than the average temperature measured... least 11 days apart from other consecutive tests. The mercury concentration must be maintained below the...

40 CFR 63.11647 - What are my monitoring requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

... temperature limit is the highest temperature measured during any run of the initial compliance test or 10... either the highest reading during the test or at 10 °F higher than the average temperature measured... least 11 days apart from other consecutive tests. The mercury concentration must be maintained below the...

Characterization of particulate matter and gaseous emissions of a C-130H aircraft.

PubMed

Corporan, Edwin; Quick, Adam; DeWitt, Matthew J

2008-04-01

The gaseous and nonvolatile particulate matter (PM) emissions of two T56-A-15 turboprop engines of a C-130H aircraft stationed at the 123rd Airlift Wing in the Kentucky Air National Guard were characterized. The emissions campaign supports the Strategic Environmental Research and Development Program (SERDP) project WP-1401 to determine emissions factors from military aircraft. The purpose of the project is to develop a comprehensive emissions measurement program using both conventional and advanced techniques to determine emissions factors of pollutants, and to investigate the spatial and temporal evolutions of the exhaust plumes from fixed and rotating wing military aircraft. Standard practices for the measurement of gaseous emissions from aircraft have been well established; however, there is no certified methodology for the measurement of aircraft PM emissions. In this study, several conventional instruments were used to physically characterize and quantify the PM emissions from the two turboprop engines. Emissions samples were extracted from the engine exit plane and transported to the analytical instrumentation via heated lines. Multiple sampling probes were used to assess the spatial variation and obtain a representative average of the engine emissions. Particle concentrations, size distributions, and mass emissions were measured using commercially available aerosol instruments. Engine smoke numbers were determined using established Society of Automotive Engineers (SAE) practices, and gaseous species were quantified via a Fourier-transform infrared-based gas analyzer. The engines were tested at five power settings, from idle to take-off power, to cover a wide range of operating conditions. Average corrected particle numbers (PNs) of (6.4-14.3) x 10(7) particles per cm3 and PN emission indices (EI) from 3.5 x 10(15) to 10.0 x 10(15) particles per kg-fuel were observed. The highest PN EI were observed for the idle power conditions. The mean particle diameter varied between 50 nm at idle to 70 nm at maximum engine power. PM mass EI ranged from 1.6 to 3.5 g/kg-fuel for the conditions tested, which are in agreement with previous T56 engine measurements using other techniques. Additional PM data, smoke numbers, and gaseous emissions will be presented and discussed.

Exposure assessment in front of a multi-band base station antenna.

PubMed

Kos, Bor; Valič, Blaž; Kotnik, Tadej; Gajšek, Peter

2011-04-01

This study investigates occupational exposure to electromagnetic fields in front of a multi-band base station antenna for mobile communications at 900, 1800, and 2100 MHz. Finite-difference time-domain method was used to first validate the antenna model against measurement results published in the literature and then investigate the specific absorption rate (SAR) in two heterogeneous, anatomically correct human models (Virtual Family male and female) at distances from 10 to 1000 mm. Special attention was given to simultaneous exposure to fields of three different frequencies, their interaction and the additivity of SAR resulting from each frequency. The results show that the highest frequency--2100 MHz--results in the highest spatial-peak SAR averaged over 10 g of tissue, while the whole-body SAR is similar at all three frequencies. At distances > 200 mm from the antenna, the whole-body SAR is a more limiting factor for compliance to exposure guidelines, while at shorter distances the spatial-peak SAR may be more limiting. For the evaluation of combined exposure, a simple summation of spatial-peak SAR maxima at each frequency gives a good estimation for combined exposure, which was also found to depend on the distribution of transmitting power between the different frequency bands. Copyright © 2010 Wiley-Liss, Inc.

Optimization of calcium carbonate content on synthesis of aluminum foam and its compressive strength characteristic

NASA Astrophysics Data System (ADS)

Sutarno, Nugraha, Bagja; Kusharjanto

2017-01-01

One of the most important characteristic of aluminum foam is compressive strength, which is reflected by its impact energy and Young's modulus. In the present research, optimization of calcium carbonate (CaCO3) content in the synthesized aluminum foam in order to obtain the highest compressive strength was carried out. The results of this study will be used to determine the CaCO3 content synthesis process parameter in pilot plant scale production of an aluminum foam. The experiment was performed by varying the concentration of calcium carbonate content, which was used as foaming agent, at constant alumina concentration (1.5 wt%), which was added as stabilizer, and temperature (725°C). It was found that 4 wt% CaCO3 gave the lowest relative density, which was 0.15, and the highest porosity, which was 85.29%, and compressive strength of as high as 0.26 Mpa. The pore morphology of the obtained aluminum foam at such condition was as follow: the average pore diameter was 4.42 mm, the wall thickness minimum of the pore was 83.24 µm, roundness of the pore was 0.91. Based on the fractal porosity, the compressive strength was inversely proportional to the porosity and huddled on a power law value of 2.91.

Extraction and characterization of three polysaccharides extracted from Opuntia ficus indica cladodes.

PubMed

Bayar, Nadia; Kriaa, Mouna; Kammoun, Radhouane

2016-11-01

The chemical extraction and the characterization of polysaccharides from mucilage (MC), pectin (PC) and total pectic mucilage fraction (TFC) of Opuntia ficus indica cladodes as well as the evaluation of their antioxidant activities was investigated. The FTIR spectroscopic analysis revealed the presence of carboxyl and hydroxyl groups corresponding to polysaccharides. Uronic acid and the total sugar contents of PC were higher than those of TFC and MC whereas ash content of MC was considerably more important. In addition, the findings showed that all the samples had little protein content and low average molecular weight compared to the results mentioned in literature. Furthermore, MC reached not only the highest water (WHC) and oil holding (OHC) capacities (7.81g/g and 1.34g/g, respectively) but also the highest antioxidant properties (DPPH and ABTS scavenging activities, β-carotene bleaching inhibition activity and reducing power). However, PC had the strongest emulsifying and foaming properties. As for TFC, it had low WHC, OHC and emulsifying properties whereas it had higher foaming properties than MC and greater antioxidant properties compared to PC. These outcomes can encourage the use of PC as a surfactant and MC and TFC as natural antioxidants in food and pharmaceutical industries. Copyright © 2016 Elsevier B.V. All rights reserved.

Determination of tricresyl phosphate air contamination in aircraft.

PubMed

Denola, G; Hanhela, P J; Mazurek, W

2011-08-01

Monitoring of tricresyl phosphate (TCP) contamination of cockpit air was undertaken in three types of military aircraft [fighter trainer (FT), fighter bomber (FB), and cargo transport (CT) aircraft]. The aircraft had a previous history of pilot complaints about cockpit air contamination suspected to originate from the engine bleed air supply through the entry of aircraft turbine engine oil (ATO) into the engine compressor. Air samples were collected in flight and on the ground during engine runs using sorbent tubes packed with Porapak Q and cellulose filters. A total of 78 air samples were analysed, from 46 different aircraft, and 48 samples were found to be below the limit of detection. Nine incidents of smoke/odour were identified during the study. The concentrations of toxic o-cresyl phosphate isomers were below the level of detection in all samples. The highest total TCP concentration was 51.3 μg m(-3), while most were generally found to be <5 μg m(-3) compared with the 8-h time-weighted average exposure limit of 100 μg m(-3) for tri-o-cresyl phosphate. The highest concentrations were found at high engine power. Although TCP contamination of cabin/cockpit air has been the subject of much concern in aviation, quantitative data are sparse.

Single-pass high harmonic generation at high repetition rate and photon flux

NASA Astrophysics Data System (ADS)

Hädrich, Steffen; Rothhardt, Jan; Krebs, Manuel; Demmler, Stefan; Klenke, Arno; Tünnermann, Andreas; Limpert, Jens

2016-09-01

Sources of short wavelength radiation with femtosecond to attosecond pulse durations, such as synchrotrons or free electron lasers, have already made possible numerous, and will facilitate more, seminal studies aimed at understanding atomic and molecular processes on fundamental length and time scales. Table-top sources of coherent extreme ultraviolet to soft x-ray radiation enabled by high harmonic generation (HHG) of ultrashort pulse lasers have also gained significant attention in the last few years due to their enormous potential for addressing a plethora of applications, therefore constituting a complementary source to large-scale facilities (synchrotrons and free electron lasers). Ti:sapphire based laser systems have been the workhorses for HHG for decades, but are limited in repetition rate and average power. On the other hand, it has been widely recognized that fostering applications in fields such as photoelectron spectroscopy and microscopy, coincidence detection, coherent diffractive imaging and frequency metrology requires a high repetition rate and high photon flux HHG sources. In this article we will review recent developments in realizing the demanding requirement of producing a high photon flux and repetition rate at the same time. Particular emphasis will be put on suitable ultrashort pulse and high average power lasers, which directly drive harmonic generation without the need for external enhancement cavities. To this end we describe two complementary schemes that have been successfully employed for high power fiber lasers, i.e. optical parametric chirped pulse amplifiers and nonlinear pulse compression. Moreover, the issue of phase-matching in tight focusing geometries will be discussed and connected to recent experiments. We will highlight the latest results in fiber laser driven high harmonic generation that currently produce the highest photon flux of all existing sources. In addition, we demonstrate the first promising applications and discuss the future direction and challenges of this new type of HHG source.

Recent GE BWR fuel experience and design evolution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wood, J.E.; Potts, G.A.; Proebstle, R.A.

1992-01-01

Reliable fuel operation is essential to the safe, reliable, and economic power production by today's commercial nuclear reactors. GE Nuclear Energy is committed to maximize fuel reliability through the progressive development of improved fuel design features and dedication to provide the maximum quality of the design features and dedication to provide the maximum quality of the design, fabrication, and operation of GE BWR fuel. Over the last 35 years, GE has designed, fabricated, and placed in operation over 82,000 BWR fuel bundles containing over 5 million fuel rods. This experience includes successful commercial reactor operation of fuel assemblies to greatermore » than 45000 MWd/MTU bundle average exposure. This paper reports that this extensive experience base has enabled clear identification and characterization of the active failure mechanisms. With this failure mechanism characterization, mitigating actions have been developed and implemented by GE to provide the highest reliability BWR fuel bundles possible.« less

High-performance radio frequency transistors based on diameter-separated semiconducting carbon nanotubes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cao, Yu; Che, Yuchi; Zhou, Chongwu, E-mail: chongwuz@usc.edu

In this paper, we report the high-performance radio-frequency transistors based on the single-walled semiconducting carbon nanotubes with a refined average diameter of ∼1.6 nm. These diameter-separated carbon nanotube transistors show excellent transconductance of 55 μS/μm and desirable drain current saturation with an output resistance of ∼100 KΩ μm. An exceptional radio-frequency performance is also achieved with current gain and power gain cut-off frequencies of 23 GHz and 20 GHz (extrinsic) and 65 GHz and 35 GHz (intrinsic), respectively. These radio-frequency metrics are among the highest reported for the carbon nanotube thin-film transistors. This study provides demonstration of radio frequency transistors based on carbon nanotubes with tailoredmore » diameter distributions, which will guide the future application of carbon nanotubes in radio-frequency electronics.« less

Ultrahigh capacity 2 × 2 MIMO RoF system at 60  GHz employing single-sideband single-carrier modulation.

PubMed

Lin, Chun-Ting; Ho, Chun-Hung; Huang, Hou-Tzu; Cheng, Yu-Hsuan

2014-03-15

This article proposes and experimentally demonstrates a radio-over-fiber system employing single-sideband single-carrier (SSB-SC) modulation at 60 GHz. SSB-SC modulation has a lower peak-to-average-power ratio than orthogonal frequency division multiplex (OFDM) modulation; therefore, the SSB-SC signals provide superior nonlinear tolerance, compared to OFDM signals. Moreover, multiple-input multiple-output (MIMO) technology was used extensively to enhance spectral efficiency. A least-mean-square-based equalizer was implemented, including MIMO channel estimation, frequency response equalization, and I/Q imbalance compensation to recover the MIMO signals. Thus, using 2×2 MIMO technology and 64-QAM SSB-SC signals, we achieved the highest data rate of 84 Gbps with 12  bit/s/Hz spectral efficiency using the 7-GHz license-free band at 60 GHz.

High-Efficiency Polycrystalline Thin Film Tandem Solar Cells.

PubMed

Kranz, Lukas; Abate, Antonio; Feurer, Thomas; Fu, Fan; Avancini, Enrico; Löckinger, Johannes; Reinhard, Patrick; Zakeeruddin, Shaik M; Grätzel, Michael; Buecheler, Stephan; Tiwari, Ayodhya N

2015-07-16

A promising way to enhance the efficiency of CIGS solar cells is by combining them with perovskite solar cells in tandem devices. However, so far, such tandem devices had limited efficiency due to challenges in developing NIR-transparent perovskite top cells, which allow photons with energy below the perovskite band gap to be transmitted to the bottom cell. Here, a process for the fabrication of NIR-transparent perovskite solar cells is presented, which enables power conversion efficiencies up to 12.1% combined with an average sub-band gap transmission of 71% for photons with wavelength between 800 and 1000 nm. The combination of a NIR-transparent perovskite top cell with a CIGS bottom cell enabled a tandem device with 19.5% efficiency, which is the highest reported efficiency for a polycrystalline thin film tandem solar cell. Future developments of perovskite/CIGS tandem devices are discussed and prospects for devices with efficiency toward and above 27% are given.

Planar waveguide concentrator used with a seasonal tracker.

PubMed

Bouchard, Sébastien; Thibault, Simon

2012-10-01

Solar concentrators offer good promise for reducing the cost of solar power. Planar waveguides equipped with a microlens slab have already been proposed as an excellent approach to produce medium to high concentration levels. Instead, we suggest the use of a cylindrical microlens array to get useful concentration without tracking during the day. To use only a seasonal tracking system and get the highest possible concentration, cylindrical microlenses are placed in the east-west orientation. Our new design has an acceptance angle in the north-south direction of ±9° and ±54° in the east-west axis. Simulation of our optimized system achieves a 4.6× average concentration level from 8:30 to 16:30 with a maximum of 8.1× and 80% optical efficiency. The low-cost advantage of waveguide-based solar concentrators could support their use in roof-mounted solar panels and eliminate the need for an expensive and heavy active tracker.

Passively Q-switched 1.6 µm Er:YAG laser with a γ-Ga2O3:Co-based glass-ceramics as a saturable absorber

NASA Astrophysics Data System (ADS)

Shi, Yang; Gao, Chunqing; Ye, Qing; Wang, Shuo; Wang, Qing; Gao, Mingwei; Loiko, Pavel; Skoptsov, Nikolai; Dymshits, Olga; Zhilin, Alexander; Zapalova, Svetlana; Tsenter, Marina; Vitkin, Vladimir; Mateos, Xavier; Yumashev, Konstantin

2018-04-01

A resonantly pumped passively Q-switched Er:YAG laser operating at 1.617 and 1.645 µm is reported with γ-Ga2O3:Co2+-based glass-ceramics (GCs) as a saturable absorber. The maximum average output power achieved from this laser was 273 mW; the highest pulse energy was 5.9 µJ, corresponding to a pulse duration of 3.0 µs at a repetition frequency of 31 kHz. To the best of our knowledge, this is the first time to use the γ-Ga2O3:Co2+-based GC as a passive Q-switcher for Er:YAG lasers and this is also the first time to obtain 1.617 µm and 1.645 µm pulses with a GC-based saturable absorber.

Joint Patch and Multi-label Learning for Facial Action Unit Detection

PubMed Central

Zhao, Kaili; Chu, Wen-Sheng; De la Torre, Fernando; Cohn, Jeffrey F.; Zhang, Honggang

2016-01-01

The face is one of the most powerful channel of nonverbal communication. The most commonly used taxonomy to describe facial behaviour is the Facial Action Coding System (FACS). FACS segments the visible effects of facial muscle activation into 30+ action units (AUs). AUs, which may occur alone and in thousands of combinations, can describe nearly all-possible facial expressions. Most existing methods for automatic AU detection treat the problem using one-vs-all classifiers and fail to exploit dependencies among AU and facial features. We introduce joint-patch and multi-label learning (JPML) to address these issues. JPML leverages group sparsity by selecting a sparse subset of facial patches while learning a multi-label classifier. In four of five comparisons on three diverse datasets, CK+, GFT, and BP4D, JPML produced the highest average F1 scores in comparison with state-of-the art. PMID:27382243

Aqueous-Containing Precursor Solutions for Efficient Perovskite Solar Cells.

PubMed

Liu, Dianyi; Traverse, Christopher J; Chen, Pei; Elinski, Mark; Yang, Chenchen; Wang, Lili; Young, Margaret; Lunt, Richard R

2018-01-01

Perovskite semiconductors have emerged as competitive candidates for photovoltaic applications due to their exceptional optoelectronic properties. However, the impact of moisture instability on perovskite films is still a key challenge for perovskite devices. While substantial effort is focused on preventing moisture interaction during the fabrication process, it is demonstrated that low moisture sensitivity, enhanced crystallization, and high performance can actually be achieved by exposure to high water content (up to 25 vol%) during fabrication with an aqueous-containing perovskite precursor. The perovskite solar cells fabricated by this aqueous method show good reproducibility of high efficiency with average power conversion efficiency (PCE) of 18.7% and champion PCE of 20.1% under solar simulation. This study shows that water-perovskite interactions do not necessarily negatively impact the perovskite film preparation process even at the highest efficiencies and that exposure to high contents of water can actually enable humidity tolerance during fabrication in air.

Phylogenetic relationships of chrysanthemums in Korea based on novel SSR markers.

PubMed

Khaing, A A; Moe, K T; Hong, W J; Park, C S; Yeon, K H; Park, H S; Kim, D C; Choi, B J; Jung, J Y; Chae, S C; Lee, K M; Park, Y J

2013-11-07

Chrysanthemums are well known for their esthetic and medicinal values. Characterization of chrysanthemums is vital for their conservation and management as well as for understanding their genetic relationships. We found 12 simple sequence repeat markers (SSRs) of 100 designed primers to be polymorphic. These novel SSR markers were used to evaluate 95 accessions of chrysanthemums (3 indigenous and 92 cultivated accessions). Two hundred alleles were identified, with an average of 16.7 alleles per locus. KNUCRY-77 gave the highest polymorphic information content value (0.879), while KNUCRY-10 gave the lowest (0.218). Similar patterns of grouping were observed with a distance-based dendrogram developed using PowerMarker and model-based clustering with Structure. Three clusters with some admixtures were identified by model-based clustering. These newly developed SSR markers will be useful for further studies of chrysanthemums, such as taxonomy and marker-assisted selection breeding.

Fluorination-enabled optimal morphology leads to over 11% efficiency for inverted small-molecule organic solar cells

PubMed Central

Deng, Dan; Zhang, Yajie; Zhang, Jianqi; Wang, Zaiyu; Zhu, Lingyun; Fang, Jin; Xia, Benzheng; Wang, Zhen; Lu, Kun; Ma, Wei; Wei, Zhixiang

2016-01-01

Solution-processable small molecules for organic solar cells have attracted intense attention for their advantages of definite molecular structures compared with their polymer counterparts. However, the device efficiencies based on small molecules are still lower than those of polymers, especially for inverted devices, the highest efficiency of which is <9%. Here we report three novel solution-processable small molecules, which contain π-bridges with gradient-decreased electron density and end acceptors substituted with various fluorine atoms (0F, 1F and 2F, respectively). Fluorination leads to an optimal active layer morphology, including an enhanced domain purity, the formation of hierarchical domain size and a directional vertical phase gradation. The optimal morphology balances charge separation and transfer, and facilitates charge collection. As a consequence, fluorinated molecules exhibit excellent inverted device performance, and an average power conversion efficiency of 11.08% is achieved for a two-fluorine atom substituted molecule. PMID:27991486

Antioxidant and antibacterial activity of six edible wild plants (Sonchus spp.) in China.

PubMed

Xia, Dao-Zong; Yu, Xin-Fen; Zhu, Zhuo-Ying; Zou, Zhuang-Dan

2011-12-01

The total phenolic and flavonoid, antioxidant and antibacterial activities of six Sonchus wild vegetables (Sonchus oleraceus L., Sonchus arvensis L., Sonchus asper (L.) Hill., Sonchus uliginosus M.B., Sonchus brachyotus DC. and Sonchus lingianus Shih) in China were investigated. The results revealed that S. arvensis extract and S. oleraceus extract contained the highest amount of phenolic and flavonoid, respectively. Among the methanol extracts of six Sonchus species, S. arvensis extract exhibited the highest radical (DPPH and ABTS+ scavenging power and lipid peroxidation inhibitory power. It also exhibited the highest reducing power at 500 µg mL⁻¹ by A (700) = 0.80. The results of antibacterial test indicated that the S. oleraceus extract showed higher activity than the other five Sonchus wild vegetables extracts, both in Gram-negative bacteria (Escherichia coli, Salmonella enterica and Vibrio parahaemolyticus) and in a Gram-positive bacterium (Staphylococcus aureus). These results indicate that Sonchus wild food plants might be applicable in natural medicine and healthy food.

Physicochemical properties and digestibility of common bean (Phaseolus vulgaris L.) starches.

PubMed

Du, Shuang-Kui; Jiang, Hongxin; Ai, Yongfeng; Jane, Jay-Lin

2014-08-08

Physicochemical properties and digestibility of pinto bean, red kidney bean, black bean and navy bean starches were analyzed. All the common bean starches had oval and spherical granules with average diameter of 25.3-27.4 μm. Amylose contents were 32.0-45.4%. Black bean starch showed the highest peak viscosity, breakdown, final viscosity and setback, whereas red kidney bean starch showed the lowest pasting temperature, peak viscosity, breakdown, and setback. Pinto bean starch showed the highest onset and peak gelatinization temperatures, and the lowest gelatinization temperature range; whereas navy bean starch exhibited the lowest values. Amylopectin of red kidney bean had the highest molecular weight (Mw) and z-average gyration radius (Rz), whereas black bean amylopectin had the lowest values of Mw and Rz. The proportions of DP 6-12, DP 13-24, DP 25-36, and DP ≥ 37 and average branch-chain lengths were 23.30-35.21%, 47.79-53.53%, 8.99-12.65%, 6.39-13.49%, and 17.91-21.56, respectively. All the native bean starches were highly resistant to enzyme digestion. Copyright © 2014 Elsevier Ltd. All rights reserved.

On the averaging area for incident power density for human exposure limits at frequencies over 6 GHz

NASA Astrophysics Data System (ADS)

Hashimoto, Yota; Hirata, Akimasa; Morimoto, Ryota; Aonuma, Shinta; Laakso, Ilkka; Jokela, Kari; Foster, Kenneth R.

2017-04-01

Incident power density is used as the dosimetric quantity to specify the restrictions on human exposure to electromagnetic fields at frequencies above 3 or 10 GHz in order to prevent excessive temperature elevation at the body surface. However, international standards and guidelines have different definitions for the size of the area over which the power density should be averaged. This study reports computational evaluation of the relationship between the size of the area over which incident power density is averaged and the local peak temperature elevation in a multi-layer model simulating a human body. Three wave sources are considered in the frequency range from 3 to 300 GHz: an ideal beam, a half-wave dipole antenna, and an antenna array. 1D analysis shows that averaging area of 20 mm  ×  20 mm is a good measure to correlate with the local peak temperature elevation when the field distribution is nearly uniform in that area. The averaging area is different from recommendations in the current international standards/guidelines, and not dependent on the frequency. For a non-uniform field distribution, such as a beam with small diameter, the incident power density should be compensated by multiplying a factor that can be derived from the ratio of the effective beam area to the averaging area. The findings in the present study suggest that the relationship obtained using the 1D approximation is applicable for deriving the relationship between the incident power density and the local temperature elevation.

Au generation centres doped n+-Si: hole-injection adjustable anode for efficient organic light emission

NASA Astrophysics Data System (ADS)

Li, Y. Z.; Ran, G. Z.; Zhao, W. Q.; Qin, G. G.

2008-08-01

An organic light-emitting diode (OLED) with an n-Si-anode usually has an efficiency evidently lower than the OLED with the same structure with a p-Si-anode due to insufficient hole injection from the n-Si anode compared with the p-Si-anode. In this study, we find that introducing Au as generation centres with a suitable concentration into the n+-Si anode can enhance hole injection to match electron injection and then considerably promote the power efficiency. With optimizing Au generation centre concentration in the n+-Si anode, the OLED with a structure of n+-Si: Au/NPB/AlQ/Sm/Au reaches a highest power efficiency of 1.0 lm W-1, evidently higher than the reported highest power efficiency of 0.2 lm W-1 for its p-Si-anode counterpart. Furthermore, when the electron injection is enhanced by adopting BPhen:Cs2CO3 partly instead of AlQ as the electron transport material, and the Au generation centre concentration in the n+-Si anode is promoted correspondingly, then a highest power efficiency of 1.8 lm W-1 is reached. The role of Au generation centres in the n+-Si anode is discussed.

Applications of Multivariate Statistical Techniques for Computer Performance Evaluation.

DTIC Science & Technology

1983-12-01

parameters has on another parameter. VII-f1 *T-. . . . . . . -,z X 71 .7 . V - AFIT/GCS/EE/83D-4 CHAPTER VIII CLUSTER ANALYSIS In data analysis the study...their highest, with bnchmk being 50% greater than the overall average of . 318 seconds and nuprocs being 147% greater than its overall average of 30.8...overall average of . 318 seconds and nuprocs being 147% greater than its overall average of 30.8. These increased values of bnchmk indicate that during

Plasma core power exhaust in ELMy H-Mode in JET with ITER-Like Wall

NASA Astrophysics Data System (ADS)

Guillemaut, C.; Metzger, C.; Appel, L.; Drewelow, P.; Horvath, L.; Matthews, G. F.; Szepesi, G.; Solano, E. R.; contributors, JET

2018-07-01

The mitigation of target heat load in future steady state fusion devices will require dissipation of a significant amount of power through radiation. Plasma operations relying on ELMy H-modes could be problematic since ELMs may transport substantial amounts of power to the target without significant dissipation. Therefore, estimation of the average ELM power exhaust from the plasma core is crucial to evaluate the potential limitation on the power dissipation in ELMy H-mode regime. A series of more than 50 Type-I ELMy H-mode discharges in JET with ITER-Like Wall (JET-ILW) with a wide range of conditions has been used here to compare the average ELM power to the average input power. The effect of input power, ELM frequency, plasma current, confinement and radiation on ELM power exhaust has been studied and reported in this paper. Good agreement has been found here with previous studies made in carbon machines. This work suggests that it should not be possible to dissipate more than 70%–80% of the input power in Type-I ELMy H-modes in JET-ILW which is consistent with the maximum radiative fraction found experimentally.

Calculated power distribution of a thermionic, beryllium oxide reflected, fast-spectrum reactor

NASA Technical Reports Server (NTRS)

Mayo, W.; Lantz, E.

1973-01-01

A procedure is developed and used to calculate the detailed power distribution in the fuel elements next to a beryllium oxide reflector of a fast-spectrum, thermionic reactor. The results of the calculations show that, although the average power density in these outer fuel elements is not far from the core average, the power density at the very edge of the fuel closest to the beryllium oxide is about 1.8 times the core avearge.

Technical options for high average power free electron milimeter-wave and laser devices

NASA Technical Reports Server (NTRS)

Swingle, James C.

1989-01-01

Many of the potential space power beaming applications require the generation of directed energy beams with respectable amounts of average power (MWs). A tutorial summary is provided here on recent advances in the laboratory aimed at producing direct conversion of electrical energy to electromagnetic radiation over a wide spectral regime from microwaves to the ultraviolet.

Compact Tunable Narrowband Terahertz-Wave Source Based on Difference Frequency Generation Pumped by Dual Fiber Lasers in MgO:LiNbO3

NASA Astrophysics Data System (ADS)

Wada, Yoshio; Satoh, Takumi; Higashi, Yasuhiro; Urata, Yoshiharu

2017-12-01

We demonstrate a high-average-power, single longitudinal-mode, and tunable terahertz (THz)-wave source based on difference frequency generation (DFG) in a MgO:LiNbO3 (MgO:LN) crystal. The waves for DFG are generated using a pair of Yb-doped pulsed fiber lasers with a master oscillator power fiber amplifier configuration. The average power of the THz-wave output reaches 450 μW at 1.07 THz (280 μm) at a linewidth of 7.2 GHz, and the tunability ranges from 0.35 to 1.07 THz under the pulse repetition frequency of 500 kHz. A short burn-in test of the THz wave is also carried out, and the output power stability is within ± 5% of the averaged power without any active stabilizing technique. The combination of MgO:LN-DFG and stable and robust fiber laser sources is highly promising for the development of high-average-power THz-wave sources, particularly in the high transmission sub-THz region. This approach may enable new applications of THz-wave spectroscopy in imaging and remote sensing.

The predictive power of local properties of financial networks

NASA Astrophysics Data System (ADS)

Caraiani, Petre

2017-01-01

The literature on analyzing the dynamics of financial networks has focused so far on the predictive power of global measures of networks like entropy or index cohesive force. In this paper, I show that the local network properties have similar predictive power. I focus on key network measures like average path length, average degree or cluster coefficient, and also consider the diameter and the s-metric. Using Granger causality tests, I show that some of these measures have statistically significant prediction power with respect to the dynamics of aggregate stock market. Average path length is most robust relative to the frequency of data used or specification (index or growth rate). Most measures are found to have predictive power only for monthly frequency. Further evidences that support this view are provided through a simple regression model.

Pulsed power systems for environmental and industrial applications

NASA Astrophysics Data System (ADS)

Neau, E. L.

1994-10-01

The development of high peak power simulators, laser drivers, free electron lasers, and Inertial Confinement Fusion drivers is being extended to high average power short-pulse machines with the capabilities of performing new roles in environmental cleanup and industrial manufacturing processes. We discuss a new class of short-pulse, high average power accelerator that achieves megavolt electron and ion beams with 10's of kiloamperes of current and average power levels in excess of 100 kW. Large treatment areas are possible with these systems because kilojoules of energy are available in each output pulse. These systems can use large area x-ray converters for applications requiring grater depth of penetration such as food pasteurization and waste treatment. The combined development of this class of accelerators and applications, and Sandia National Laboratories, is called Quantum Manufacturing.

Performance assessment of individual and ensemble data-mining techniques for gully erosion modeling.

PubMed

Pourghasemi, Hamid Reza; Yousefi, Saleh; Kornejady, Aiding; Cerdà, Artemi

2017-12-31

Gully erosion is identified as an important sediment source in a range of environments and plays a conclusive role in redistribution of eroded soils on a slope. Hence, addressing spatial occurrence pattern of this phenomenon is very important. Different ensemble models and their single counterparts, mostly data mining methods, have been used for gully erosion susceptibility mapping; however, their calibration and validation procedures need to be thoroughly addressed. The current study presents a series of individual and ensemble data mining methods including artificial neural network (ANN), support vector machine (SVM), maximum entropy (ME), ANN-SVM, ANN-ME, and SVM-ME to map gully erosion susceptibility in Aghemam watershed, Iran. To this aim, a gully inventory map along with sixteen gully conditioning factors was used. A 70:30% randomly partitioned sets were used to assess goodness-of-fit and prediction power of the models. The robustness, as the stability of models' performance in response to changes in the dataset, was assessed through three training/test replicates. As a result, conducted preliminary statistical tests showed that ANN has the highest concordance and spatial differentiation with a chi-square value of 36,656 at 95% confidence level, while the ME appeared to have the lowest concordance (1772). The ME model showed an impractical result where 45% of the study area was introduced as highly susceptible to gullying, in contrast, ANN-SVM indicated a practical result with focusing only on 34% of the study area. Through all three replicates, the ANN-SVM ensemble showed the highest goodness-of-fit and predictive power with a respective values of 0.897 (area under the success rate curve) and 0.879 (area under the prediction rate curve), on average, and correspondingly the highest robustness. This attests the important role of ensemble modeling in congruently building accurate and generalized models which emphasizes the necessity to examine different models integrations. The result of this study can prepare an outline for further biophysical designs on gullies scattered in the study area. Copyright © 2017 Elsevier B.V. All rights reserved.

Characterization of advanced electric propulsion systems

NASA Technical Reports Server (NTRS)

Ray, P. K.

1982-01-01

Characteristics of several advanced electric propulsion systems are evaluated and compared. The propulsion systems studied are mass driver, rail gun, MPD thruster, hydrogen free radical thruster and mercury electron bombardment ion engine. These are characterized by specific impulse, overall efficiency, input power, average thrust, power to average thrust ratio and average thrust to dry weight ratio. Several important physical characteristics such as dry system mass, accelerator length, bore size and current pulse requirement are also evaluated in appropriate cases. Only the ion engine can operate at a specific impulse beyond 2000 sec. Rail gun, MPD thruster and free radical thruster are currently characterized by low efficiencies. Mass drivers have the best performance characteristics in terms of overall efficiency, power to average thrust ratio and average thrust to dry weight ratio. But, they can only operate at low specific impulses due to large power requirements and are extremely long due to limitations of driving current. Mercury ion engines have the next best performance characteristics while operating at higher specific impulses. It is concluded that, overall, ion engines have somewhat better characteristics as compared to the other electric propulsion systems.

The Physiological Profile of Junior Soccer Players at SSBB Surabaya Bhakti

NASA Astrophysics Data System (ADS)

Nashirudin, M.; Kusnanik, N. W.

2018-01-01

Soccer players are required to have good physical fitness in order to achieve optimum accomplishment; physical fitness stands as the foundation of technical and tactical proficiency as well as the mental maturity during the matches. The purpose of this study was to identify the physiological profile of junior soccer players of SSB Surabaya Bhakti age 16-17. The research was conducted at 20 junior soccer players. This research was quantitative with descriptive analysis. Data were collected by testing of physiological (anaerobic power and capacity including explosive leg power, speed, agility; aerobic capacity: cardiovascular endurance). Data was analyzed using percentage. The result showed that the percentage of explosive leg power of junior soccer players were 30% (good category), speed was 85% (average category), right agility was 90% (average category), left agility was 75% (average category). On the other hand, the aerobic power and capacity of the junior soccer players in this study was 50% (average category). The conclusion of this research is that the physiological profile of junior soccer players at SSB Surabaya Bhakti age 16-17 was majority in average category.

Competition and Cooperation of Distributed Generation and Power System

NASA Astrophysics Data System (ADS)

Miyake, Masatoshi; Nanahara, Toshiya

Advances in distributed generation technologies together with the deregulation of an electric power industry can lead to a massive introduction of distributed generation. Since most of distributed generation will be interconnected to a power system, coordination and competition between distributed generators and large-scale power sources would be a vital issue in realizing a more desirable energy system in the future. This paper analyzes competitions between electric utilities and cogenerators from the viewpoints of economic and energy efficiency based on the simulation results on an energy system including a cogeneration system. First, we examine best response correspondence of an electric utility and a cogenerator with a noncooperative game approach: we obtain a Nash equilibrium point. Secondly, we examine the optimum strategy that attains the highest social surplus and the highest energy efficiency through global optimization.

Concurrent validity, discriminatory power and feasibility of the instrument for Identification of Parents At Risk for child Abuse and Neglect (IPARAN).

PubMed

Horrevorts, Esther M B; van Grieken, Amy; Mieloo, Cathelijne L; Hafkamp-de Groen, Esther; Bannink, Rienke; Bouwmeester-Landweer, Merian B R; Broeren, Suzanne; Raat, Hein

2017-08-23

To determine the feasibility, concurrent validity and discriminatory power of the instrument for Identification of Parents At Risk for child Abuse and Neglect (IPARAN) among Dutch parents with a newborn child. Community paediatrics. Data from a controlled trial were used. In total, 2659 Dutch parents with a newborn child were invited to participate. Of the 2659 parents, 759 parents filled in the consent form and participated in the study. Concurrent validity was determined by calculating correlations-using the Pearson's correlation (r)-between the IPARAN score and related constructs from the following instruments: the Empowerment Questionnaire 2.0, the Family Functioning Questionnaire and the Parenting Stress Questionnaire. Discriminatory power was determined by calculating receiver operating characteristic (ROC) curves between high-risk mothers and low-risk mothers according to their scores on the related constructs. Feasibility was determined by examining the percentage of missing answers. In terms of concurrent validity, we found that 3 out of 12 correlations between the IPARAN score and related constructs were strong (ie, r>0.50) and 4 out of 12 were medium (ie, r=0.30-0.49). In terms of discriminatory power, mothers with a score in the borderline/clinical range or lowest 10 percent (P10) range of the related constructs (high-risk mothers) had a higher IPARAN score than mothers with a score in the normal range or highest 90 percent (P90) range of the related constructs (low-risk mothers). Effect sizes varied from d=0.37 to d=1.93, and the area under the ROC curve varied from 0.62 to 0.93. Regarding feasibility, the part of the IPARAN filled in by the mother had on average 0.7% missing answers, whereas the part of the IPARAN filled in by the father had on average 1.7% missing answers. The results of this study support the concurrent validity, discriminatory power and feasibility of the IPARAN among a population of Dutch parents with a newborn child. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Fundamental formulae for wave-energy conversion.

PubMed

Falnes, Johannes; Kurniawan, Adi

2015-03-01

The time-average wave power that is absorbed from an incident wave by means of a wave-energy conversion (WEC) unit, or by an array of WEC units-i.e. oscillating immersed bodies and/or oscillating water columns (OWCs)-may be mathematically expressed in terms of the WEC units' complex oscillation amplitudes, or in terms of the generated outgoing (diffracted plus radiated) waves, or alternatively, in terms of the radiated waves alone. Following recent controversy, the corresponding three optional expressions are derived, compared and discussed in this paper. They all provide the correct time-average absorbed power. However, only the first-mentioned expression is applicable to quantify the instantaneous absorbed wave power and the associated reactive power. In this connection, new formulae are derived that relate the 'added-mass' matrix, as well as a couple of additional reactive radiation-parameter matrices, to the difference between kinetic energy and potential energy in the water surrounding the immersed oscillating WEC array. Further, a complex collective oscillation amplitude is introduced, which makes it possible to derive, by a very simple algebraic method, various simple expressions for the maximum time-average wave power that may be absorbed by the WEC array. The real-valued time-average absorbed power is illustrated as an axisymmetric paraboloid defined on the complex collective-amplitude plane. This is a simple illustration of the so-called 'fundamental theorem for wave power'. Finally, the paper also presents a new derivation that extends a recently published result on the direction-average maximum absorbed wave power to cases where the WEC array's radiation damping matrix may be singular and where the WEC array may contain OWCs in addition to oscillating bodies.

Assessment of genetic diversity, population structure and relationships in Indian and non-Indian genotypes of finger millet (Eleusine coracana (L.) Gaertn) using genomic SSR markers.

PubMed

Ramakrishnan, M; Antony Ceasar, S; Duraipandiyan, V; Al-Dhabi, N A; Ignacimuthu, S

2016-01-01

We evaluated the genetic variation and population structure in Indian and non-Indian genotypes of finger millet using 87 genomic SSR primers. The 128 finger millet genotypes were collected and genomic DNA was isolated. Eighty-seven genomic SSR primers with 60-70 % GC contents were used for PCR analysis of 128 finger millet genotypes. The PCR products were separated and visualized on a 6 % polyacrylamide gel followed by silver staining. The data were used to estimate major allele frequency using Power Marker v3.0. Dendrograms were constructed based on the Jaccard's similarity coefficient. Statistical fitness and population structure analyses were performed to find the genetic diversity. The mean major allele frequency was 0.92; the means of polymorphic alleles were 2.13 per primer and 1.45 per genotype; the average polymorphism was 59.94 % per primer and average PIC value was 0.44 per primer. Indian genotypes produced an additional 0.21 allele than non-Indian genotypes. Gene diversity was in the range from 0.02 to 0.35. The average heterozygosity was 0.11, close to 100 % homozygosity. The highest inbreeding coefficient was observed with SSR marker UGEP67. The Jaccard's similarity coefficient value ranged from 0.011 to 0.836. The highest similarity value was 0.836 between genotypes DPI009-04 and GPU-45. Indian genotypes were placed in Eleusine coracana major cluster (EcMC) 1 along with 6 non-Indian genotypes. AMOVA showed that molecular variance in genotypes from various geographical regions was 4 %; among populations it was 3 % and within populations it was 93 %. PCA scatter plot analysis showed that GPU-28, GPU-45 and DPI009-04 were closely dispersed in first component axis. In structural analysis, the genotypes were divided into three subpopulations (SP1, SP2 and SP3). All the three subpopulations had an admixture of alleles and no pure line was observed. These analyses confirmed that all the genotypes were genetically diverse and had been grouped based on their geographic regions.

Average Faculty Salary Reaches $41,650, Up 6.1% in a Year, AAUP Survey Finds.

ERIC Educational Resources Information Center

Evangelauf, Jean

1990-01-01

This study shows that by type of institution, salaries are highest at doctorate-granting public and private universities. By sector, faculty members at private, independent institutions continue to have the highest earnings. The salary gap between men and women persists, with women earning less than men at every rank. (MLW)

What is the Impact of Utility Demand Charges on a DCFC host

DOE Office of Scientific and Technical Information (OSTI.GOV)

Francfort, James Edward

The PEV Electric Vehicle Supply Equipment (EVSE) delivered by The EV Project included both AC Level 2 and DCFC units. Over 100 of these dual-port Blink DC fast chargers were deployed by The EV Project. These DCFCs were installed in workplaces and in publicly accessible locations near traffic hubs, retail centers, parking lots, restaurants, and similar locations. The Blink DCFC is capable of charging at power up to 60 kW. Its dual-port design sequences the charge from one port to the other, delivering power to only one of two vehicles connected at a time. The actual power delivered through amore » port is determined by the PEV’s on-board battery management system (BMS). Both the power and the total energy used to recharge a PEV can represent a significant cost for the charging site host. Many electric utilities impose fees for power demand as part of their commercial rate structure. The demand charge incurred by a customer is related to the peak power used during a monthly billing cycle. This is in contrast to the cumulative total energy usage that is the more familiar utility charge seen for most residential services. A demand charge is typically assessed for the highest average power over any 15 minute interval during the monthly billing cycle. One objective of The EV Project was to identify and elucidate the motivations and barriers to potential DCFC site hosts. The application of electric utility demand charges is one such potential barrier. This subject was introduced in the paper: DC Fast Charge - Demand Charge Reduction1. It discussed demand charge impact in general terms in order to focus on potential mitigation actions. This paper identifies specific cases in order to quantify the impact of demand charges on EV Project DCFC hosts.« less

Operational frequency stability of rubidium and cesium frequency standards

NASA Technical Reports Server (NTRS)

Lavery, J. E.

1973-01-01

The frequency stabilities under operational conditions of several commercially available rubidium and cesium frequency standards were determined from experimental data for frequency averaging times from 10 to the 7th power s and are presented in table and graph form. For frequency averaging times between 10 to the 5th power and 10 to the 7th power s, the rubidium standards tested have a stability of between 10 to the minus 12th power and 5 x 10 to the minus 12th power, while the cesium standards have a stability of between 2 x 10 to the minus 13th power and 5 x 10 to the minus 13th power.

Limitations of oxygen uptake and leg muscle activity during ascending evacuation in stairways.

PubMed

Halder, Amitava; Kuklane, Kalev; Gao, Chuansi; Miller, Michael; Delin, Mattias; Norén, Johan; Fridolf, Karl

2018-01-01

Stair ascending performance is critical during evacuation from buildings and underground infrastructures. Healthy subjects performed self-paced ascent in three settings: 13 floor building, 31 floor building, 33 m stationary subway escalator. To investigate leg muscle and cardiorespiratory capacities and how they constrain performance, oxygen uptake (VO 2 ), heart rate (HR) and ascending speed were measured in all three; electromyography (EMG) in the first two. The VO 2 and HR ranged from 89 to 96% of the maximum capacity reported in the literature. The average highest VO 2 and HR ranged from 39 to 41 mL·kg -1 ·min -1 and 162 to 174 b·min -1 , respectively. The subjects were able to sustain their initial preferred maximum pace for a short duration, while the average step rate was 92-95 steps·min -1 . In average, VO 2 reached relatively stable values at ≈37 mL·kg -1 ·min -1 . EMG amplitudes decreased significantly and frequencies were unchanged. Speed reductions indicate that climbing capacity declined in the process of fatigue development. In the two buildings, the reduction of muscle power allowed the subjects to extend their tolerance and complete ascents in the 48 m and 109 m high stairways in 2.9 and 7.8 min, respectively. Muscle activity interpretation squares were developed and proved advantageous to observe fatigue and recovery over time. Copyright © 2017 Elsevier Ltd. All rights reserved.

Buparvaquone Nanostructured Lipid Carrier: Development of an Affordable Delivery System for the Treatment of Leishmaniases

PubMed Central

Löbenberg, Raimar; Cotrim, Paulo Cesar

2017-01-01

Buparvaquone (BPQ), a veterinary drug, was formulated as nanostructured lipid carriers (NLC) for leishmaniases treatment. The formulation design addressed poor water solubility of BPQ and lack of human drug delivery system. The DSC/TG and microscopy methods were used for solid lipids screening. Softisan® 154 showed highest BPQ solubility in both methods. The BPQ solubility in liquid lipids using HPLC revealed Miglyol® 812 as the best option. Response surface methodology (RSM) was used to identify the optimal Softisan154 : Miglyol 812 ratios (7 : 10 to 2 : 1) and Kolliphor® P188 and Tween® 80 concentration (>3.0% w/w) aiming for z-average in the range of 100–300 nm for macrophage delivery. The NLC obtained by high-pressure homogenization showed low z-averages (<350 nm), polydispersity (<0.3), and encapsulation efficiency close to 100%. DSC/TG and microscopy in combination proved to be a powerful tool to select the solid lipid. The relationship among the variables, demonstrated by a linear mathematical model using RSM, allowed generating a design space. This design space showed the limits in which changes in the variables influenced the z-average. Therefore, these drug delivery systems have the potential to improve the availability of affordable medicines due to the low cost of raw materials, using well established, reliable, and feasible scale-up technology. PMID:28255558

Automation in the Space Station module power management and distribution Breadboard

NASA Technical Reports Server (NTRS)

Walls, Bryan; Lollar, Louis F.

1990-01-01

The Space Station Module Power Management and Distribution (SSM/PMAD) Breadboard, located at NASA's Marshall Space Flight Center (MSFC) in Huntsville, Alabama, models the power distribution within a Space Station Freedom Habitation or Laboratory module. Originally designed for 20 kHz ac power, the system is now being converted to high voltage dc power with power levels on a par with those expected for a space station module. In addition to the power distribution hardware, the system includes computer control through a hierarchy of processes. The lowest level process consists of fast, simple (from a computing standpoint) switchgear, capable of quickly safing the system. The next level consists of local load center processors called Lowest Level Processors (LLP's). These LLP's execute load scheduling, perform redundant switching, and shed loads which use more than scheduled power. The level above the LLP's contains a Communication and Algorithmic Controller (CAC) which coordinates communications with the highest level. Finally, at this highest level, three cooperating Artificial Intelligence (AI) systems manage load prioritization, load scheduling, load shedding, and fault recovery and management. The system provides an excellent venue for developing and examining advanced automation techniques. The current system and the plans for its future are examined.

Femtosecond Cr:LiSAF and Cr:LiCAF lasers pumped by tapered diode lasers.

PubMed

Demirbas, Umit; Schmalz, Michael; Sumpf, Bernd; Erbert, Götz; Petrich, Gale S; Kolodziejski, Leslie A; Fujimoto, James G; Kärtner, Franz X; Leitenstorfer, Alfred

2011-10-10

We report compact, low-cost and efficient Cr:Colquiriite lasers that are pumped by high brightness tapered laser diodes. The tapered laser diodes provided 1 to 1.2 W of output power around 675 nm, at an electrical-to-optical conversion efficiency of about 30%. Using a single tapered diode laser as the pump source, we have demonstrated output powers of 500 mW and 410 mW together with slope efficiencies of 47% and 41% from continuous wave (cw) Cr:LiSAF and Cr:LiCAF lasers, respectively. In cw mode-locked operation, sub-100-fs pulse trains with average power between 200 mW and 250 mW were obtained at repetition rates around 100 MHz. Upon pumping the Cr:Colquiriite lasers with two tapered laser diodes (one from each side of the crystal), we have observed scaling of cw powers to 850 mW in Cr:LiSAF and to 650 mW in Cr:LiCAF. From the double side pumped Cr:LiCAF laser, we have also obtained ~220 fs long pulses with 5.4 nJ of pulse energy at 77 MHz repetition rate. These are the highest energy levels reported from Cr:Colquiriite so far at these repetition rates. Our findings indicate that tapered diodes in the red spectral region are likely to become the standard pump source for Cr:Colquiriite lasers in the near future. Moreover, the simplified pumping scheme might facilitate efficient commercialization of Cr:Colquiriite systems, bearing the potential to significantly boost applications of cw and femtosecond lasers in this spectral region (750-1000 nm).

Design and characterisation of a phased antenna array for intact breast hyperthermia.

PubMed

Curto, Sergio; Garcia-Miquel, Aleix; Suh, Minyoung; Vidal, Neus; Lopez-Villegas, Jose M; Prakash, Punit

2018-05-01

Currently available hyperthermia technology is not well suited to treating cancer malignancies in the intact breast. This study investigates a microwave applicator incorporating multiple patch antennas, with the goal of facilitating controllable power deposition profiles for treating lesions at diverse locations within the intact breast. A 3D-computational model was implemented to assess power deposition profiles with 915 MHz applicators incorporating a hemispheric groundplane and configurations of 2, 4, 8, 12, 16 and 20 antennas. Hemispheric breast models of 90 mm and 150 mm diameter were considered, where cuboid target volumes of 10 mm edge length (1 cm 3 ) and 30 mm edge length (27 cm 3 ) were positioned at the centre of the breast, and also located 15 mm from the chest wall. The average power absorption (αPA) ratio expressed as the ratio of the PA in the target volume and in the full breast was evaluated. A 4-antenna proof-of-concept array was fabricated and experimentally evaluated. Computational models identified an optimal inter-antenna spacing of 22.5° along the applicator circumference. Applicators with 8 and 12 antennas excited with constant phase presented the highest αPA at centrally located and deep-seated targets, respectively. Experimental measurements with a 4-antenna proof-of-concept array illustrated the potential for electrically steering power deposition profiles by adjusting the relative phase of the signal at antenna inputs. Computational models and experimental results suggest that the proposed applicator may have potential for delivering conformal thermal therapy in the intact breast.

Temporal and spatial variations in road traffic noise for different frequency components in metropolitan Taichung, Taiwan.

PubMed

Wang, Ven-Shing; Lo, Ei-Wen; Liang, Chih-Hsiang; Chao, Keh-Ping; Bao, Bo-Ying; Chang, Ta-Yuan

2016-12-01

Road traffic noise exposure has been associated with auditory and non-auditory health effects, but few studies report noise characteristics. This study determines 24-h noise levels and analyzes their frequency components to investigate associations between seasons, meteorology, land-use types, and traffic. We set up 50 monitoring stations covering ten different land-use types and conducted measurements at three times of the year to obtain 24-h-average A-weighted equivalent noise levels (L Aeq , 24h ) and frequency analyses from 2013 to 2014 in Taichung, Taiwan. Information on land-use types, road parameters, traffic flow rates, and meteorological variables was also collected for analysis with the annual averages of road traffic noise and its frequency components. The annual average L Aeq , 24h in Taichung was 66.4 ± 4.7 A-weighed decibels (dBA). Significant differences in L Aeq , 24h and frequency components were observed between land-use types (all p-values < 0.001), but not between seasons, with the highest two noise levels of 71.2 ± 1.0 dBA and 70.0 ± 2.6 dBA measured in stream-channel and commercial areas, with the highest component being 61.4 ± 5.3 dBA at 1000 Hz. Road width, traffic flow rates, and land-use types were significantly associated with annual average L Aeq , 24h (all p-values < 0.050). Noise levels at 125 Hz had the highest correlation with total traffic (Spearman's coefficient = 0.795) and the highest prediction in the multiple linear regression (R 2  = 0.803; adjusted R 2  = 0.765). These findings reveal the spatial variation in road traffic noise exposure in Taichung. The highest correlation and predictive capacity was observed between this variation and noise levels at 125 Hz. We recommend that governmental agencies should take actions to reduce noise levels from traffic vehicles. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effect of prepubertal and postpubertal growth and age at first calving on production and reproduction traits during the first 3 lactations in Holstein dairy cattle.

PubMed

Krpálková, L; Cabrera, V E; Vacek, M; Stípková, M; Stádník, L; Crump, P

2014-05-01

The objective of this study was to evaluate the effect of body condition score (BCS), body weight (BW), average daily weight gain (ADG), and age at first calving (AFC) of Holstein heifers on production and reproduction parameters in the 3 subsequent lactations. The data set consisted of 780 Holstein heifers calved at 2 dairy farms in the Czech Republic from 2007 to 2011. Their BW and BCS were measured at monthly intervals during the rearing period (5 to 18 mo of age), and the milk production and reproduction data of the first 3 lactations were collected over an 8-yr period (2005 to 2012). The highest milk yield in the first lactation was found in the group with medium ADG (5 to 14 mo of age; 0.949 to 0.850 kg of ADG). The highest average milk yield over lifetime performance was detected in heifers with the highest total ADG (≥ 0.950 kg/d). The difference in milk yield between the evaluated groups of highest ADG (in total and postpubertal growth ≥ 0.950 kg/d and in prepubertal growth ≥ 0.970 kg/d) and the lowest ADG (≤ 0.849 kg/d) was approximately 1,000 kg/305 d per cow. The highest milk yield in the first lactation was found in the group with the highest AFC ≥ 751 d, for which fat and protein content in the milk was not reduced. Postpubertal growth (11 to 14 mo of age) had the greatest effect on AFC. The group with lowest AFC ≤ 699 d showed a negative effect on milk yield but only in the first 100 d of the first parity. The highest ADG was detrimental to reproduction parameters in the first lactation. The highest BW at 14 mo (≥ 420 kg) led to lower AFC. Groups according to BCS at 14 mo showed no differences in AFC or milk yield in the first lactation or lifetime average production per lactation. We concluded that low AFC ≤ 699 d did not show a negative effect on subsequent production and reproduction parameters. Therefore, a shorter rearing period is recommended for dairy herds with suitable management. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Combined Effects of Lignosus rhinocerotis Supplementation and Resistance Training on Isokinetic Muscular Strength and Power, Anaerobic and Aerobic Fitness Level, and Immune Parameters in Young Males.

PubMed

Chen, Chee Keong; Hamdan, Nor Faeiza; Ooi, Foong Kiew; Wan Abd Hamid, Wan Zuraida

2016-01-01

This study investigated the effects of Lignosus rhinocerotis (LRS) supplementation and resistance training (RT) on isokinetic muscular strength and power, anaerobic and aerobic fitness, and immune parameters in young males. Participants were randomly assigned to four groups: Control (C), LRS, RT, and combined RT-LRS (RT-LRS). Participants in the LRS and RT-LRS groups consumed 500 mg of LRS daily for 8 weeks. RT was conducted 3 times/week for 8 weeks for participants in the RT and RT-LRS groups. The following parameters were measured before and after the intervention period: Anthropometric data, isokinetic muscular strength and power, and anaerobic and aerobic fitness. Blood samples were also collected to determine immune parameters. Isokinetic muscular strength and power were increased ( P < 0.05) in participants of both RT and RT-LRS groups. RT-LRS group had shown increases ( P < 0.05) in shoulder extension peak torque, shoulder flexion and extension average power, knee flexion peak torque, and knee flexion and extension average power. There were also increases ( P < 0.05) in anaerobic power and capacity and aerobic fitness in this group. Similarly, RT group had increases ( P < 0.05) in shoulder flexion average power, knee flexion and extension peak torque, and knee flexion and extension average power. In addition, increases ( P < 0.05) in anaerobic power and capacity, aerobic fitness, T lymphocytes (CD3 and CD4), and B lymphocytes (CD19) counts were observed in the RT group. RT elicited increased isokinetic muscular strength and power, anaerobic and aerobic fitness, and immune parameters among young males. However, supplementation with LRS during RT did not provide additive benefits.

Combined Effects of Lignosus rhinocerotis Supplementation and Resistance Training on Isokinetic Muscular Strength and Power, Anaerobic and Aerobic Fitness Level, and Immune Parameters in Young Males

PubMed Central

Chen, Chee Keong; Hamdan, Nor Faeiza; Ooi, Foong Kiew; Wan Abd Hamid, Wan Zuraida

2016-01-01

Background: This study investigated the effects of Lignosus rhinocerotis (LRS) supplementation and resistance training (RT) on isokinetic muscular strength and power, anaerobic and aerobic fitness, and immune parameters in young males. Methods: Participants were randomly assigned to four groups: Control (C), LRS, RT, and combined RT-LRS (RT-LRS). Participants in the LRS and RT-LRS groups consumed 500 mg of LRS daily for 8 weeks. RT was conducted 3 times/week for 8 weeks for participants in the RT and RT-LRS groups. The following parameters were measured before and after the intervention period: Anthropometric data, isokinetic muscular strength and power, and anaerobic and aerobic fitness. Blood samples were also collected to determine immune parameters. Results: Isokinetic muscular strength and power were increased (P < 0.05) in participants of both RT and RT-LRS groups. RT-LRS group had shown increases (P < 0.05) in shoulder extension peak torque, shoulder flexion and extension average power, knee flexion peak torque, and knee flexion and extension average power. There were also increases (P < 0.05) in anaerobic power and capacity and aerobic fitness in this group. Similarly, RT group had increases (P < 0.05) in shoulder flexion average power, knee flexion and extension peak torque, and knee flexion and extension average power. In addition, increases (P < 0.05) in anaerobic power and capacity, aerobic fitness, T lymphocytes (CD3 and CD4), and B lymphocytes (CD19) counts were observed in the RT group. Conclusions: RT elicited increased isokinetic muscular strength and power, anaerobic and aerobic fitness, and immune parameters among young males. However, supplementation with LRS during RT did not provide additive benefits. PMID:27833721

Discriminating ability of Cirrus and RTVue optical coherence tomography in different stages of glaucoma

PubMed Central

Mittal, Deepti; Dubey, Suneeta; Gandhi, Monica; Pegu, Julie; Bhoot, Madhu; Gupta, Yadunandan Prasad

2018-01-01

Purpose: The aim of this study is to determine which parameter of Cirrus and RTVue optical coherence tomography (OCT) has the highest ability to discriminate between early, moderate, and advanced glaucoma. Simultaneously, to compare the performance of the two OCT devices in terms of their ability to differentiate the three stages of glaucoma. Further, to analyze the macular parameters of both devices and compare them with the conventional retinal nerve fiber layer (RNFL) parameters. Methods: One hundred and twenty eyes (30 healthy and 90 glaucomatous [30 mild, 30 moderate, and 30 advanced glaucoma]) of 65 participants (15 healthy, 50 glaucomatous [15 mild, 15 moderate, and 20 advanced glaucoma]) underwent Cirrus and RTVue OCT scanning on a single visit. Results: Average RNFL thickness and superior RNFL thickness of both the devices and inferior (ganglion cell complex [GCC] of RTVue device best differentiated normals from all stage glaucomatous eyes (P > 0.05). Cirrus average RNFL thickness and superior RNFL thickness performed better than other parameters (P < 0.05) in differentiating early glaucoma from moderate and advanced. In differentiating advanced from early and moderate glaucoma, RTVue average, superior, and inferior RNFL thickness and inferior GCC parameters had the highest discriminating ability (P < 0.05). Conclusion: Overall, average RNFL thickness had the highest ability to distinguish different stages of the disease. No significant difference was found between RTVue and Cirrus OCT device in different severity levels. No significant difference was observed between RNFL and macular parameters in different stages of glaucoma. PMID:29676314

A measurement of summertime dry deposition of ambient air particulates and associated metallic pollutants in Central Taiwan.

PubMed

Fang, Guor-Cheng; Chiang, Hung-Che; Chen, Yu-Cheng; Xiao, You-Fu; Wu, Chia-Ming; Kuo, Yu-Chen

2015-04-01

The purpose of this study is to characterize metallic elements associated with atmospheric particulate matter in the dry deposition plate, total suspended particulate, fine particles, and coarse particles at Taichung Harbor and Gong Ming Junior High School (airport) in central Taiwan at a sampling site from June 2013 to August 2013. The results indicated that: (1) the average concentrations of the metallic elements Cr and Cd were highest at the Gong Ming Junior High School (airport), and the average concentrations of the metallic elements Ni, Cu, and Pb were highest at the Taichung Harbor sampling site. (2) The high smelting industry density and export/import rate of heavily loaded cargos were the main reasons leading to these findings. (3) The average metallic element dry deposition and metallic element PM(2.5-10) all followed the order of Pb > Cr > Cu > Ni > Cd at the two sampling sites. However, the average metallic elements Cu and Pb were found to have the highest dry deposition velocities and concentrations in PM(2.5) for the two sampling sites in this study. (4) The correlation coefficients of ambient air particle dry deposition and concentration with wind speed at the airport were higher than those from the harbor sampling site. The wind and broad open spaces at Taichung Airport were the possible reasons for the increasing correlation coefficients for ambient air particle concentration and dry deposition with wind speed at the Taichung Airport sampling site.

Discriminating ability of Cirrus and RTVue optical coherence tomography in different stages of glaucoma.

PubMed

Mittal, Deepti; Dubey, Suneeta; Gandhi, Monica; Pegu, Julie; Bhoot, Madhu; Gupta, Yadunandan Prasad

2018-05-01

The aim of this study is to determine which parameter of Cirrus and RTVue optical coherence tomography (OCT) has the highest ability to discriminate between early, moderate, and advanced glaucoma. Simultaneously, to compare the performance of the two OCT devices in terms of their ability to differentiate the three stages of glaucoma. Further, to analyze the macular parameters of both devices and compare them with the conventional retinal nerve fiber layer (RNFL) parameters. One hundred and twenty eyes (30 healthy and 90 glaucomatous [30 mild, 30 moderate, and 30 advanced glaucoma]) of 65 participants (15 healthy, 50 glaucomatous [15 mild, 15 moderate, and 20 advanced glaucoma]) underwent Cirrus and RTVue OCT scanning on a single visit. Average RNFL thickness and superior RNFL thickness of both the devices and inferior (ganglion cell complex [GCC] of RTVue device best differentiated normals from all stage glaucomatous eyes (P > 0.05). Cirrus average RNFL thickness and superior RNFL thickness performed better than other parameters (P < 0.05) in differentiating early glaucoma from moderate and advanced. In differentiating advanced from early and moderate glaucoma, RTVue average, superior, and inferior RNFL thickness and inferior GCC parameters had the highest discriminating ability (P < 0.05). Overall, average RNFL thickness had the highest ability to distinguish different stages of the disease. No significant difference was found between RTVue and Cirrus OCT device in different severity levels. No significant difference was observed between RNFL and macular parameters in different stages of glaucoma.

Evaluation of Techniques Used to Estimate Cortical Feature Maps

PubMed Central

Katta, Nalin; Chen, Thomas L.; Watkins, Paul V.; Barbour, Dennis L.

2011-01-01

Functional properties of neurons are often distributed nonrandomly within a cortical area and form topographic maps that reveal insights into neuronal organization and interconnection. Some functional maps, such as in visual cortex, are fairly straightforward to discern with a variety of techniques, while other maps, such as in auditory cortex, have resisted easy characterization. In order to determine appropriate protocols for establishing accurate functional maps in auditory cortex, artificial topographic maps were probed under various conditions, and the accuracy of estimates formed from the actual maps was quantified. Under these conditions, low-complexity maps such as sound frequency can be estimated accurately with as few as 25 total samples (e.g., electrode penetrations or imaging pixels) if neural responses are averaged together. More samples are required to achieve the highest estimation accuracy for higher complexity maps, and averaging improves map estimate accuracy even more than increasing sampling density. Undersampling without averaging can result in misleading map estimates, while undersampling with averaging can lead to the false conclusion of no map when one actually exists. Uniform sample spacing only slightly improves map estimation over nonuniform sample spacing typical of serial electrode penetrations. Tessellation plots commonly used to visualize maps estimated using nonuniform sampling are always inferior to linearly interpolated estimates, although differences are slight at higher sampling densities. Within primary auditory cortex, then, multiunit sampling with at least 100 samples would likely result in reasonable feature map estimates for all but the highest complexity maps and the highest variability that might be expected. PMID:21889537

The rate of transient beta frequency events predicts behavior across tasks and species

PubMed Central

Law, Robert; Tsutsui, Shawn; Moore, Christopher I; Jones, Stephanie R

2017-01-01

Beta oscillations (15-29Hz) are among the most prominent signatures of brain activity. Beta power is predictive of healthy and abnormal behaviors, including perception, attention and motor action. In non-averaged signals, beta can emerge as transient high-power 'events'. As such, functionally relevant differences in averaged power across time and trials can reflect changes in event number, power, duration, and/or frequency span. We show that functionally relevant differences in averaged beta power in primary somatosensory neocortex reflect a difference in the number of high-power beta events per trial, i.e. event rate. Further, beta events occurring close to the stimulus were more likely to impair perception. These results are consistent across detection and attention tasks in human magnetoencephalography, and in local field potentials from mice performing a detection task. These results imply that an increased propensity of beta events predicts the failure to effectively transmit information through specific neocortical representations. PMID:29106374

Adaptive pitch control for variable speed wind turbines

DOEpatents

Johnson, Kathryn E [Boulder, CO; Fingersh, Lee Jay [Westminster, CO

2012-05-08

An adaptive method for adjusting blade pitch angle, and controllers implementing such a method, for achieving higher power coefficients. Average power coefficients are determined for first and second periods of operation for the wind turbine. When the average power coefficient for the second time period is larger than for the first, a pitch increment, which may be generated based on the power coefficients, is added (or the sign is retained) to the nominal pitch angle value for the wind turbine. When the average power coefficient for the second time period is less than for the first, the pitch increment is subtracted (or the sign is changed). A control signal is generated based on the adapted pitch angle value and sent to blade pitch actuators that act to change the pitch angle of the wind turbine to the new or modified pitch angle setting, and this process is iteratively performed.

Power scaling of supercontinuum seeded megahertz-repetition rate optical parametric chirped pulse amplifiers.

PubMed

Riedel, R; Stephanides, A; Prandolini, M J; Gronloh, B; Jungbluth, B; Mans, T; Tavella, F

2014-03-15

Optical parametric chirped-pulse amplifiers with high average power are possible with novel high-power Yb:YAG amplifiers with kW-level output powers. We demonstrate a compact wavelength-tunable sub-30-fs amplifier with 11.4 W average power with 20.7% pump-to-signal conversion efficiency. For parametric amplification, a beta-barium borate crystal is pumped by a 140 W, 1 ps Yb:YAG InnoSlab amplifier at 3.25 MHz repetition rate. The broadband seed is generated via supercontinuum generation in a YAG crystal.

Cigarette Prices and Community Price Comparisons in US Military Retail Stores

PubMed Central

Poston, Walker S.C.; Haddock, Christopher K.; Jahnke, Sara A.; Smith, Elizabeth; Malone, Ruth E.; Jitnarin, Nattinee

2016-01-01

BACKGROUND Tobacco pricing impacts use, yet military retailers sell discounted cigarettes. No systematic research has examined how military retail stores use internal community comparisons to set prices. We analyzed data obtained through a Freedom of Information Act request on community price comparisons used by military retail to set cigarette prices. METHODS Data on cigarette prices were obtained directly from military retailers (exchanges) from January 2013–March 2014. Complete pricing data was provided from exchanges on 114 military installations. RESULTS The average price for a pack of Marlboro cigarettes in military exchanges was $5.51, which was similar to the average lowest community price ($5.45; Mean Difference=−0.06; p=0.104) and almost a $1.00 lower than the average highest price ($6.44). Military retail prices were 2.1%, 6.2%, and 13.7% higher than the lowest, average, and highest community comparisons and 18.2% of exchange prices violated pricing instructions. There was a negative correlation (r = −.21, p = 0.02) between the number of community stores surveyed and exchange cigarette prices. CONCLUSIONS There was no significant difference between prices for cigarettes on military installations and the lowest average community comparison, and in some locations the prices violated DoD policy. US Marine Corps exchanges had the lowest prices, which is of concern given that the Marines also have the highest rates of tobacco use in the DoD. Given the relationship between tobacco product prices and demand, a common minimum (or floor) shelf price for tobacco products should be set for all exchanges and discount coupon redemptions should be prohibited. PMID:27553357

Generation of switchable domain wall and Cubic-Quintic nonlinear Schrödinger equation dark pulse

NASA Astrophysics Data System (ADS)

Tiu, Z. C.; Suthaskumar, M.; Zarei, A.; Tan, S. J.; Ahmad, H.; Harun, S. W.

2015-10-01

A switchable domain-wall (DW) and Cubic-Quintic nonlinear Schrödinger equation (CQNLSE) dark soliton pulse generation are demonstrated in Erbium-doped fiber laser (EDFL) for the first time. The DW pulse train operates at 1575 nm with a fundamental repetition rate of 1.52 MHz and pulse width of 203 ns as the pump power is increased above the threshold pump power of 80 mW. The highest pulse energy of 2.24 nJ is obtained at the maximum pump power of 140 mW. CQNLSE pulse can also be realized from the same cavity by adjusting the polarization state but at a higher threshold pump power of 104 mW. The repetition rate and pulse width of the CQNLSE dark pulses are obtained at 1.52 MHz and 219 ns, respectively. The highest energy of 0.58 nJ is obtained for the CQNLSE pulse at pump power of 140 mW.

Low statistical power in biomedical science: a review of three human research domains.

PubMed

Dumas-Mallet, Estelle; Button, Katherine S; Boraud, Thomas; Gonon, Francois; Munafò, Marcus R

2017-02-01

Studies with low statistical power increase the likelihood that a statistically significant finding represents a false positive result. We conducted a review of meta-analyses of studies investigating the association of biological, environmental or cognitive parameters with neurological, psychiatric and somatic diseases, excluding treatment studies, in order to estimate the average statistical power across these domains. Taking the effect size indicated by a meta-analysis as the best estimate of the likely true effect size, and assuming a threshold for declaring statistical significance of 5%, we found that approximately 50% of studies have statistical power in the 0-10% or 11-20% range, well below the minimum of 80% that is often considered conventional. Studies with low statistical power appear to be common in the biomedical sciences, at least in the specific subject areas captured by our search strategy. However, we also observe evidence that this depends in part on research methodology, with candidate gene studies showing very low average power and studies using cognitive/behavioural measures showing high average power. This warrants further investigation.

Low statistical power in biomedical science: a review of three human research domains

PubMed Central

Dumas-Mallet, Estelle; Button, Katherine S.; Boraud, Thomas; Gonon, Francois

2017-01-01

Studies with low statistical power increase the likelihood that a statistically significant finding represents a false positive result. We conducted a review of meta-analyses of studies investigating the association of biological, environmental or cognitive parameters with neurological, psychiatric and somatic diseases, excluding treatment studies, in order to estimate the average statistical power across these domains. Taking the effect size indicated by a meta-analysis as the best estimate of the likely true effect size, and assuming a threshold for declaring statistical significance of 5%, we found that approximately 50% of studies have statistical power in the 0–10% or 11–20% range, well below the minimum of 80% that is often considered conventional. Studies with low statistical power appear to be common in the biomedical sciences, at least in the specific subject areas captured by our search strategy. However, we also observe evidence that this depends in part on research methodology, with candidate gene studies showing very low average power and studies using cognitive/behavioural measures showing high average power. This warrants further investigation. PMID:28386409

Heterodyne laser diagnostic system

DOEpatents

Globig, Michael A.; Johnson, Michael A.; Wyeth, Richard W.

1990-01-01

The heterodyne laser diagnostic system includes, in one embodiment, an average power pulsed laser optical spectrum analyzer for determining the average power of the pulsed laser. In another embodiment, the system includes a pulsed laser instantaneous optical frequency measurement for determining the instantaneous optical frequency of the pulsed laser.

18 CFR 301.6 - Appendix 1 instructions.

Code of Federal Regulations, 2013 CFR

2013-04-01

..., DEPARTMENT OF ENERGY REGULATIONS FOR FEDERAL POWER MARKETING ADMINISTRATIONS AVERAGE SYSTEM COST METHODOLOGY... 4: Average System Cost (f) The filing Utility must reference and attach work papers, documentation... 18 Conservation of Power and Water Resources 1 2013-04-01 2013-04-01 false Appendix 1 instructions...

18 CFR 301.6 - Appendix 1 instructions.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., DEPARTMENT OF ENERGY REGULATIONS FOR FEDERAL POWER MARKETING ADMINISTRATIONS AVERAGE SYSTEM COST METHODOLOGY... 4: Average System Cost (f) The filing Utility must reference and attach work papers, documentation... 18 Conservation of Power and Water Resources 1 2011-04-01 2011-04-01 false Appendix 1 instructions...

18 CFR 301.6 - Appendix 1 instructions.

Code of Federal Regulations, 2014 CFR

2014-04-01

..., DEPARTMENT OF ENERGY REGULATIONS FOR FEDERAL POWER MARKETING ADMINISTRATIONS AVERAGE SYSTEM COST METHODOLOGY... 4: Average System Cost (f) The filing Utility must reference and attach work papers, documentation... 18 Conservation of Power and Water Resources 1 2014-04-01 2014-04-01 false Appendix 1 instructions...

18 CFR 301.6 - Appendix 1 instructions.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., DEPARTMENT OF ENERGY REGULATIONS FOR FEDERAL POWER MARKETING ADMINISTRATIONS AVERAGE SYSTEM COST METHODOLOGY... 4: Average System Cost (f) The filing Utility must reference and attach work papers, documentation... 18 Conservation of Power and Water Resources 1 2012-04-01 2012-04-01 false Appendix 1 instructions...

Distinguished Lecture Series - Balancing the Energy & Climate Budget

ScienceCinema

None

2017-12-09

The average American uses 11400 Watts of power continuously. This is the equivalent of burning 114 x100 Watt light bulbs, all the time. The average person globally uses 2255 Watts of power, or a little less than 23 x100 Watt light bulbs.

1.5-μm high-average power laser amplifier using a Er,Yb:glass planar waveguide for coherent Doppler lidar

NASA Astrophysics Data System (ADS)

Sakimura, Takeshi; Watanabe, Yojiro; Ando, Toshiyuki; Kameyama, Shumpei; Asaka, Kimio; Tanaka, Hisamichi; Yanagisawa, Takayuki; Hirano, Yoshihito; Inokuchi, Hamaki

2012-11-01

We have developed a 1.5-μm eye-safe wavelength high average power laser amplifier using an Er,Yb:glass planar waveguide for coherent Doppler LIDAR. Large cooling surface of the planar waveguide enabled high average power pumping for Er,Yb:glass which has low thermal fracture limit. Nonlinear effects are suppressed by the large beam size which is designed by the waveguide thickness and the beam width of the planar direction. Multi-bounce optical path configuration and high-intensity pumping provide high-gain and high-efficient operation using three-level laser material. With pulsed operation, the maximum pulse energy of 1.9 mJ was achieved at the repetition rate of 4 kHz. Output average power of the amplified signal was 7.6W with the amplified gain of more than 20dB. This amplifier is suitable for coherent Doppler LIDAR to enhance the measurable range.

Geomagnetism during solar cycle 23: Characteristics.

PubMed

Zerbo, Jean-Louis; Amory-Mazaudier, Christine; Ouattara, Frédéric

2013-05-01

On the basis of more than 48 years of morphological analysis of yearly and monthly values of the sunspot number, the aa index, the solar wind speed and interplanetary magnetic field, we point out the particularities of geomagnetic activity during the period 1996-2009. We especially investigate the last cycle 23 and the long minimum which followed it. During this period, the lowest values of the yearly averaged IMF (3 nT) and yearly averaged solar wind speed (364 km/s) are recorded in 1996, and 2009 respectively. The year 2003 shows itself particular by recording the highest value of the averaged solar wind (568 km/s), associated to the highest value of the yearly averaged aa index (37 nT). We also find that observations during the year 2003 seem to be related to several coronal holes which are known to generate high-speed wind stream. From the long time (more than one century) study of solar variability, the present period is similar to the beginning of twentieth century. We especially present the morphological features of solar cycle 23 which is followed by a deep solar minimum.

Retinal specializations and visual ecology in an animal with an extremely elaborate pupil shape: The Little skate Leucoraja (Raja) erinacea Mitchell, 1825.

PubMed

Jinson, S Terrell; Liebich, Jan; Senft, Stephen L; Mäthger, Lydia M

2018-05-14

Investigating retinal specializations offers insights into eye functionality. Using retinal wholemount techniques, we investigated the distribution of retinal ganglion cells in the Little skate Leucoraja erinacea by (1) dye-backfilling into the optic nerve prior to retinal wholemounting; (2) Nissl-staining of retinal wholemounts. Retinas were examined for regional specializations (higher numbers) of ganglion cells that would indicate higher visual acuity in those areas. Total ganglion cell number were low compared to other elasmobranchs (backfilled: average 49,713 total ganglion cells, average peak cell density 1,315 ganglion cells mm -2 ; Nissl-stained: average 47,791 total ganglion cells, average peak cell density 1,319 ganglion cells mm -2 ). Ganglion cells fit into three size categories: small (5-20µm); medium (20-30µm); large: (≥ 30µm), and they were not homogeneously distributed across the retina. There was a dorsally located horizontal visual streak with increased ganglion cell density; additionally, there were approximately 3 local maxima in ganglion cell distribution (potential areae centrales) within this streak in which densities were highest. Using computerized tomography (CT) and micro-CT, geometrical dimensions of the eye were obtained. Combined with ganglion cell distributions, spatial resolving power was determined to be between 1.21 to 1.37 cycles per degree. Additionally, photoreceptor sizes across different retinal areas varied; photoreceptors were longest within the horizontal visual streak. Variations in the locations of retinal specializations appear to be related to the animal's anatomy: shape of the head and eyes, position of eyes, location of tapetum, and shape of pupil, as well as the visual demands associated with lifestyle and habitat type. This article is protected by copyright. All rights reserved. © 2018 Wiley Periodicals, Inc.

Development of on-line laser power monitoring system

NASA Astrophysics Data System (ADS)

Ding, Chien-Fang; Lee, Meng-Shiou; Li, Kuan-Ming

2016-03-01

Since the laser was invented, laser has been applied in many fields such as material processing, communication, measurement, biomedical engineering, defense industries and etc. Laser power is an important parameter in laser material processing, i.e. laser cutting, and laser drilling. However, the laser power is easily affected by the environment temperature, we tend to monitor the laser power status, ensuring there is an effective material processing. Besides, the response time of current laser power meters is too long, they cannot measure laser power accurately in a short time. To be more precisely, we can know the status of laser power and help us to achieve an effective material processing at the same time. To monitor the laser power, this study utilize a CMOS (Complementary metal-oxide-semiconductor) camera to develop an on-line laser power monitoring system. The CMOS camera captures images of incident laser beam after it is split and attenuated by beam splitter and neutral density filter. By comparing the average brightness of the beam spots and measurement results from laser power meter, laser power can be estimated. Under continuous measuring mode, the average measuring error is about 3%, and the response time is at least 3.6 second shorter than thermopile power meters; under trigger measuring mode which enables the CMOS camera to synchronize with intermittent laser output, the average measuring error is less than 3%, and the shortest response time is 20 millisecond.

High-efficiency, 154  W CW, diode-pumped Raman fiber laser with brightness enhancement.

PubMed

Glick, Yaakov; Fromzel, Viktor; Zhang, Jun; Ter-Gabrielyan, Nikolay; Dubinskii, Mark

2017-01-20

We demonstrate a high-power, high-efficiency Raman fiber laser pumped directly by laser diode modules at 978 nm. 154 W of CW power were obtained at a wavelength of 1023 nm with an optical to optical efficiency of 65%. A commercial graded-index (GRIN) core fiber acts as the Raman fiber in a power oscillator configuration, which includes spectral selection to prevent generation of the second Stokes. In addition, brightness enhancement of the pump beam by a factor of 8.4 is attained due to the Raman gain distribution profile in the GRIN fiber. To the best of our knowledge this is the highest power and highest efficiency Raman fiber laser demonstrated in any configuration allowing brightness enhancement (i.e., in either cladding-pumped configuration or with GRIN fibers, excluding step-index core pumped), regardless of pumping scheme (i.e., either diode pumped or fiber laser pumped).

High power eye-safe Er3+:YVO4 laser diode-pumped at 976 nm and emitting at 1603 nm

NASA Astrophysics Data System (ADS)

Newburgh, G. A.; Dubinskii, M.

2016-02-01

We report on the performance of an eye-safe laser based on a Er:YVO4 single crystal, diode-pumped at 976 nm (4I15/2-->4I11/2 transition) and operating at 1603 nm (4I13/2-->4I15/2 transition) with good beam quality. A 10 mm long Er3+:YVO4 slab, cut with its c-axis perpendicular to the laser cavity axis, was pumped in σ-polarization and lased in π-polarization. The laser operated in a quasi-continuous wave (Q-CW) regime with nearly 9 W output power, and with a slope efficiency of about 39% with respect to absorbed power. This is believed to be the highest efficiency and highest power achieved from an Er3+:YVO4 laser pumped in the 970-980 nm absorption band.

High-average-power CTH:YAG for the medical environment

NASA Astrophysics Data System (ADS)

Wright, Sidney P.; Adamkiewicz, Edward J.; Moulton, Peter F.

1992-06-01

Medical procedures such as arthroscopy have placed increasing demands on the output performance of the CTH:YAG laser at 2.1 micrometers . Intensive research has been conducted to improve the average power, pulse energies, and rep rates while reducing any failure mechanisms. The results of this work is reported along with a discussion of the important engineering parameters concerning the design of a high power medical CTH:YAG laser.

137Cs contamination over Transylvania region (Romania) after Chernobyl Nuclear Power Plant Accident.

PubMed

Begy, R Cs; Simon, H; Vasilache, D; Kelemen, Sz; Cosma, C

2017-12-01

Following the radionuclide releases due to Chernobyl Nuclear Power Plant accident, various studies were completed by researchers all over the world in order to measure the surface contaminations by artificial radionuclides. The aim of this study was to evaluate 137 Cs surface contamination and to create an inventory distribution for Transylvania region (Romania) after the Chernobyl event using γ spectrometric measurements on soil samples collected from 153 locations. The results were compared to measured data from the Danube Delta and Moldova Republic, as well as to 137 Cs concentrations from the rest of Europe reported by literature. The 137 Cs surface concentrations in soil samples ranged between 0.4±0.1kBqm -2 and 301.1±3.0kBqm -2 , having an average of 8.3±0.2kBqm -2 , with more elevated values in the mountain areas (18.3±0.6kBqm -2 ) compared to the hills and plains (2.6±0.1kBqm -2 ). Taking into consideration the cardinal regions, the northern and western regions received the least amount of 137 Cs (2.9±0.1kBqm -2 ), while the southern part received 16.3±0.6kBqm -2 . Sampling points with eastern slope exposure received the highest average (27.8±0.5kBqm -2 ), while southern, north-western and north-eastern ones received less than 8kBqm -2 . Two hotspots are reported at Iezer-Ighiel (72.7±5.9kBqm -2 ) and Tulgheș areas (51.5±0.6kBqm -2 ). Copyright © 2017 Elsevier B.V. All rights reserved.

Development and characterization of a high yield transportable pulsed neutron source with efficient and compact pulsed power system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Verma, Rishi, E-mail: rishiv9@gmail.com, E-mail: rishiv@barc.gov.in; Mishra, Ekansh; Dhang, Prosenjit

2016-09-15

The results of characterization experiments carried out on a newly developed dense plasma focus device based intense pulsed neutron source with efficient and compact pulsed power system are reported. Its high current sealed pseudospark switch based low inductance capacitor bank with maximum stored energy of ∼10 kJ is segregated into four modules of ∼2.5 kJ each and it cumulatively delivers peak current in the range of 400 kA–600 kA (corresponding to charging voltage range of 14 kV–18 kV) in a quarter time period of ∼2 μs. The neutron yield performance of this device has been optimized by discretely varying deuteriummore » filling gas pressure in the range of 6 mbar–11 mbar at ∼17 kV/550 kA discharge. At ∼7 kJ/8.5 mbar operation, the average neutron yield has been measured to be in the order of ∼4 × 10{sup 9} neutrons/pulse which is the highest ever reported neutron yield from a plasma focus device with the same stored energy. The average forward to radial anisotropy in neutron yield is found to be ∼2. The entire system is contained on a moveable trolley having dimensions 1.5 m × 1 m × 0.7 m and its operation and control (up to the distance of 25 m) are facilitated through optically isolated handheld remote console. The overall compactness of this system provides minimum proximity to small as well as large samples for irradiation. The major intended application objective of this high neutron yield dense plasma focus device development is to explore the feasibility of active neutron interrogation experiments by utilization of intense pulsed neutron sources.« less

Development and characterization of a high yield transportable pulsed neutron source with efficient and compact pulsed power system.

PubMed

Verma, Rishi; Mishra, Ekansh; Dhang, Prosenjit; Sagar, Karuna; Meena, Manraj; Shyam, Anurag

2016-09-01

The results of characterization experiments carried out on a newly developed dense plasma focus device based intense pulsed neutron source with efficient and compact pulsed power system are reported. Its high current sealed pseudospark switch based low inductance capacitor bank with maximum stored energy of ∼10 kJ is segregated into four modules of ∼2.5 kJ each and it cumulatively delivers peak current in the range of 400 kA-600 kA (corresponding to charging voltage range of 14 kV-18 kV) in a quarter time period of ∼2 μs. The neutron yield performance of this device has been optimized by discretely varying deuterium filling gas pressure in the range of 6 mbar-11 mbar at ∼17 kV/550 kA discharge. At ∼7 kJ/8.5 mbar operation, the average neutron yield has been measured to be in the order of ∼4 × 10 9 neutrons/pulse which is the highest ever reported neutron yield from a plasma focus device with the same stored energy. The average forward to radial anisotropy in neutron yield is found to be ∼2. The entire system is contained on a moveable trolley having dimensions 1.5 m × 1 m × 0.7 m and its operation and control (up to the distance of 25 m) are facilitated through optically isolated handheld remote console. The overall compactness of this system provides minimum proximity to small as well as large samples for irradiation. The major intended application objective of this high neutron yield dense plasma focus device development is to explore the feasibility of active neutron interrogation experiments by utilization of intense pulsed neutron sources.

Fiber-based tunable repetition rate source for deep tissue two-photon fluorescence microscopy.

PubMed

Charan, Kriti; Li, Bo; Wang, Mengran; Lin, Charles P; Xu, Chris

2018-05-01

Deep tissue multiphoton imaging requires high peak power to enhance signal and low average power to prevent thermal damage. Both goals can be advantageously achieved through laser repetition rate tuning instead of simply adjusting the average power. We show that the ideal repetition rate for deep two-photon imaging in the mouse brain is between 1 and 10 MHz, and we present a fiber-based source with an arbitrarily tunable repetition rate within this range. The performance of the new source is compared to a mode-locked Ti:Sapphire (Ti:S) laser for in vivo imaging of mouse brain vasculature. At 2.5 MHz, the fiber source requires 5.1 times less average power to obtain the same signal as a standard Ti:S laser operating at 80 MHz.

Investigation of strongyle EPG values in horse mares relative to known age, number positive, and level of egg shedding in field studies on 26 farms in Central Kentucky (2010-2011).

PubMed

Lyons, E T; Tolliver, S C; Kuzmina, T A

2012-06-01

A parasite study was done in 1,300 horse mares on 26 farms in Central Kentucky over a 5-month period in 2010 and 2011. The mares included 1,114 Thoroughbreds (TB) on 24 farms, 64 Standardbreds (SB) on 1 farm, and 122 mixed light horse types (MLH) on 1 farm. The objective of this research was to determine strongyle eggs per gram of feces (EPG) counts for evaluation by known age, number positive, and level of egg shedding by the mares. This was done to establish strongyle EPG profiles for the mares to aid in determining whether antiparasitic treatment was necessary. Eggs found were considered those of small strongyles. (A) For the Thoroughbred mares, (1) 362 (32%) were EPG-positive, and (2) the average (percentage) of EPG-positive mares by year of age was 3-5 (54%), 6-10 (36%), 11-15 (24%), 16-20 (17%), and >20 (21%); (3) EPG average counts were similar for all age categories except for the 6- to 10-year-olds, which were higher; (4) and the average (percentage) of positive mares by 100 units of EPG counts was ≤100 (50%), ≤200 (62%), ≤300 (70%), ≤400 (76%), ≤500 (80%), and >500 (20%). (B) For the Standardbred mares, 31 (48%) were EPG-positive; (2) the average (percentage) of EPG-positive mares by year of age (no >20 sampled) was lowest for the 3-5 and 16-20 categories and highest for the 6-10 and 11-15 groups; (3) EPG average counts by years of age were lowest for 3-5, 11-15, and 16-20 groups and highest for the 6-10 group; and (4) the average (percentage) of positive mares by 100 units of EPGs was 62% for the ≤100 category, 71-84% for ≤200 to ≤400 units, and the highest (97%) for the ≤500 unit. (C) For the mixed light horse type mares: (1) 94 (77%) were EPG-positive, (2) the average (percentage) of EPG-positive mares by age was lowest for the two oldest age groups, higher for the 11 to 15-year-old age group, and highest for the two youngest age groups; (3) EPG average counts by year of age were lowest for the 16-20 group, higher for the 6-10 and >20 groups, and highest for 3-5 and 11-15 groups; (4) the average (percentage) of positive mares by 100 units of EPG counts was lowest for the ≤100 category (23%), increasing about 10% progressively in ≤200 to ≤500 categories, but lower (37%) for the >500 category. (D) For all the three mare types (TB, SB, and MLH), 37% of the mares were EPG-positive, and 63% of the mares were EPG-negative; for the age (years) of positive mares, about one half belonged to the 3-5 category and a progressive decrease was seen for the 6-10, 11-15, and 16-20 groups, and 36% for the >20-year-olds; the mean strongyle EPGs highest range was seen in the 11- to 15-year-olds; the highest mean was in the 6- to 10-year-olds, and the lowest mean in the 3- to 5- and 16- to 20-year-olds. For the grouping of the strongyle EPG values by units of 100, three-fourths were in the ≤500 category, and the lowest percentage was for the >500 category. This research showed the value of strongyle EPG profiling for the mares. It was most useful for TBs where data from a large number of horses showed that over two-thirds were EPG-negative, indicating that there would be no known problem in deciding not to deworm them. While data were not as clear-cut on the SB and MLH mares, several of those which were negative and with "low" EPG values could be excluded from antiparasitic treatment.

A Comparative Study of Scientific Publications in Health Care Sciences and Services from Mainland China, Taiwan, Japan, and India (2007–2014)

PubMed Central

Lv, Yipeng; Tang, Bihan; Liu, Xu; Xue, Chen; Liu, Yuan; Kang, Peng; Zhang, Lulu

2015-01-01

In this study, we aimed to compare the quantity and quality of publications in health care sciences and services journals from the Chinese mainland, Taiwan, Japan, and India. Journals in this category of the Science Citation Index Expanded were included in the study. Scientific papers were retrieved from the Web of Science online database. Quality was measured according to impact factor, citation of articles, number of articles published in top 10 journals, and the 10 most popular journals by country (area). In the field of health care sciences and services, the annual incremental rates of scientific articles published from 2007 to 2014 were higher than rates of published scientific articles in all fields. Researchers from the Chinese mainland published the most original articles and reviews and had the highest accumulated impact factors, highest total article citations, and highest average citation. Publications from India had the highest average impact factor. In the field of health care sciences and services, China has made remarkable progress during the past eight years in the annual number and percentage of scientific publications. Yet, there is room for improvement in the quantity and quality of such articles. PMID:26712774

A Comparative Study of Scientific Publications in Health Care Sciences and Services from Mainland China, Taiwan, Japan, and India (2007-2014).

PubMed

Lv, Yipeng; Tang, Bihan; Liu, Xu; Xue, Chen; Liu, Yuan; Kang, Peng; Zhang, Lulu

2015-12-24

In this study, we aimed to compare the quantity and quality of publications in health care sciences and services journals from the Chinese mainland, Taiwan, Japan, and India. Journals in this category of the Science Citation Index Expanded were included in the study. Scientific papers were retrieved from the Web of Science online database. Quality was measured according to impact factor, citation of articles, number of articles published in top 10 journals, and the 10 most popular journals by country (area). In the field of health care sciences and services, the annual incremental rates of scientific articles published from 2007 to 2014 were higher than rates of published scientific articles in all fields. Researchers from the Chinese mainland published the most original articles and reviews and had the highest accumulated impact factors, highest total article citations, and highest average citation. Publications from India had the highest average impact factor. In the field of health care sciences and services, China has made remarkable progress during the past eight years in the annual number and percentage of scientific publications. Yet, there is room for improvement in the quantity and quality of such articles.

Seasonality of tuberculosis in Israel, 2001-2011.

PubMed

Margalit, I; Block, C; Mor, Z

2016-12-01

Several studies have suggested that the incidence of tuberculosis (TB) varies with the seasons. To determine the seasonality of TB in Israel and to explore possible associations with climatic variables. Laboratory-confirmed TB cases reported between 2001 and 2011 in individuals resident in Israel for at least 1 year before diagnosis were included in the study. Climatic variables included average temperature and average ultraviolet radiation. The mean serum 25-hydroxyvitamin D level of the population was also recorded. Of all 2653 TB cases, incidence peaked during spring (n = 712) and reached its nadir during the fall (n = 577), with a case proportion amplitude (CPA) of 5.1% (P = 0.036). Individuals born in the Horn of Africa exhibited a CPA of 9.5% (P = 0.077). Mean population 25-hydroxyvitamin D level was significantly correlated with the seasonal pattern of the disease. Southern Israel had the highest global radiation and, counter-instinctively, the highest TB incidence. TB exhibited a seasonal tendency in Israel, with the spring peak/fall nadir pattern found elsewhere. Vitamin D is suspected to be an explanatory variable for this seasonal phenomenon. The finding that the highest incidence is in the area receiving the highest global radiation suggests population-related vulnerability to vitamin D deficiency.

An Evaluation of Functional Sit-to-Stand Power in Cohorts of Healthy Adults Aged 18-97 Years.

PubMed

Glenn, Jordan M; Gray, Michelle; Vincenzo, Jennifer; Paulson, Sally; Powers, Melissa

2017-04-01

This investigation examined differences in functional sit-to-stand power/velocity between cohorts of adults aged 18-97 years. This study included 264 healthy adults classified into four cohorts (18-40, C1; 60-69, C2; 70-79, C2; ≥ 80, C4). Participants completed the sit-to-stand task five times. Power and velocity were measured via the TENDO power analyzer. Absolute average power was maintained from C1-C3, but decreased (p < .01) in C4. Absolute peak power decreased between C1-C2 (p < .01), was similar between C2-C3, and decreased in C4 (p < .01). Relative (to body weight) average and peak power decreased between C1-C2 (p < .01), was similar between C2-C3, and decreased in C4 (p < .01). Average velocity was similar between C1 and C2, but decreased in C3 (p < .01) and C4 (p < .01), respectively. Peak velocity was significantly different between all cohorts (p < .01). Declines in functional power may plateau during the seventh and eighth decades, accelerating after 80 years.

Medical expenditures in division I collegiate athletics: an analysis by sport and gender.

PubMed

Kaeding, Christopher C; Borchers, James; Oman, Janine; Pedroza, Angela

2014-09-01

Medical expenses for collegiate athletics include providing a training room with its supplies, equipment, personnel costs, and insurance coverage. Additional expenses beyond the training room include imaging, diagnostic testing, specialty consultations, and surgeries. We hypothesized that there would be no difference in average expenses or number of claims between male and female athletes over a 5-year period. Prospective patient cohort. A sports medicine center serving athletes in Big 10 Conference intercollegiate sports. All medical claims and charges for 36 varsity teams were analyzed from 2005 to 2010. The teams were categorized into 3 groups: female-only teams, male-only teams, and coed teams. Analysis of sports with corresponding male and female teams was also performed. Claims and charges for medical care for 36 intercollegiate athletic teams over 5 years. Individual team claims and charges were stable over the study period. In 11 of the 14 sex-matched sports, the female teams had higher average annual charges. After normalizing for roster size in the sex-matched sports, females had 0.97 more average annual claims (P < 0.01) and $1459 higher annual charges (P = 0.001) than their male counterparts. The charges per claim were similar between the sexes. The 5 teams with the highest average annual charges were football, wrestling, softball, women's crew, and men's lacrosse. When normalized for roster size, the 5 sports with the highest average annual charges per athlete were softball, women's diving, men's basketball, wrestling, and men's gymnastics. Charges per claim were similar between the sex-matched sports, but the female sports had a higher number of annual claims per athlete and thus higher total charges per athlete/year. Football had the highest average annual total charges as a team, but when normalized for roster size football charges per athlete/year were similar to those of other sports.

Recent trends in power system reliability and implications for evaluating future investments in resiliency

DOE PAGES

Larsen, Peter H.; LaCommare, Kristina H.; Eto, Joseph H.; ...

2016-10-27

Here, this study examines the relationship between annual changes in electricity reliability reported by a large cross-section of U.S. electricity distribution utilities over a period of 13 years and a broad set of potential explanatory variables, including weather and utility characteristics. We find statistically significant correlations between the average number of power interruptions experienced annually and above average wind speeds, precipitation, lightning strikes, and a measure of population density: customers per line mile. We also find significant relationships between the average number of minutes of power interruptions experienced and above average wind speeds, precipitation, cooling degree-days, and one strategy usedmore » to mitigate the impacts of severe weather: the amount of underground transmission and distribution line miles. Perhaps most importantly, we find a significant time trend of increasing annual average number of minutes of power interruptions over time—especially when interruptions associated with extreme weather are included. Lastly, the research method described in this analysis can provide a basis for future efforts to project long-term trends in reliability and the associated benefits of strategies to improve grid resiliency to severe weather—both in the U.S. and abroad.« less

Wider income gaps, wider waistbands? An ecological study of obesity and income inequality

PubMed Central

Pickett, K.; Kelly, S.; Brunner, E.; Lobstein, T.; Wilkinson, R.

2005-01-01

Objectives: To see if obesity, deaths from diabetes, and daily calorie intake are associated with income inequality among developed countries. Design: Ecological study of 21 developed countries. Countries: Countries were eligible for inclusion if they were among the top 50 countries with the highest gross national income per capita by purchasing power parity in 2002, had a population over 3 million, and had available data on income inequality and outcome measures. Main outcome measures: Percentage of obese (body mass index >30) adult men and women, diabetes mortality rates, and calorie consumption per capita per day. Results: Adjusting for gross national per capita income, income inequality was positively correlated with the percentage of obese men (r = 0.48, p = 0.03), the percentage of obese women (r = 0.62, p = 0.003), diabetes mortality rates per 1 million people (r = 0.46, p = 0.04), and average calories per capita per day (r = 0.50, p = 0.02). Correlations were stronger if analyses were weighted for population size. The effect of income inequality on female obesity was independent of average calorie intake. Conclusions: Obesity, diabetes mortality, and calorie consumption were associated with income inequality in developed countries. Increased nutritional problems may be a consequence of the psychosocial impact of living in a more hierarchical society. PMID:16020644

Wider income gaps, wider waistbands? An ecological study of obesity and income inequality.

PubMed

Pickett, Kate E; Kelly, Shona; Brunner, Eric; Lobstein, Tim; Wilkinson, Richard G

2005-08-01

To see if obesity, deaths from diabetes, and daily calorie intake are associated with income inequality among developed countries. Ecological study of 21 developed countries.Countries: Countries were eligible for inclusion if they were among the top 50 countries with the highest gross national income per capita by purchasing power parity in 2002, had a population over 3 million, and had available data on income inequality and outcome measures. Percentage of obese (body mass index >30) adult men and women, diabetes mortality rates, and calorie consumption per capita per day. Adjusting for gross national per capita income, income inequality was positively correlated with the percentage of obese men (r = 0.48, p = 0.03), the percentage of obese women (r = 0.62, p = 0.003), diabetes mortality rates per 1 million people (r = 0.46, p = 0.04), and average calories per capita per day (r = 0.50, p = 0.02). Correlations were stronger if analyses were weighted for population size. The effect of income inequality on female obesity was independent of average calorie intake. Obesity, diabetes mortality, and calorie consumption were associated with income inequality in developed countries. Increased nutritional problems may be a consequence of the psychosocial impact of living in a more hierarchical society.

Exposure to PM2.5 and PAHs from the Tong Liang, China epidemiological study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chow, J.C.; Watson, J.G.; Chen, L.W.A.

2006-07-01

Chemically speciated PM2.5 and particle-bound polycyclic aromatic hydrocarbon (PAH) measurements were made at three sites near urban Tong Liang, Chongqing, a Chinese inland city where coal combustion is used for electricity generation and residential purposes outside of the central city. Ambient sampling was based on 72-hr averages between 3/2/2002 and 2/26/2003. Elevated PM2.5 and PAH concentrations were observed at all three sites, with the highest concentrations found in winter and the lowest in summer. This reflects a coupling effect of source variability and meteorological conditions. The PM2.5 mass estimated from sulfate, nitrate, ammonium, organics, elemental carbon, crustal material, and saltmore » corresponded with the annual average gravimetric mass within 10%. Carbonaceous aerosol was the dominant species, while positive correlations between organic carbon and trace elements (e.g., As, Se, Br, Pb, and Zn) were consistent with coal-burning and motor vehicle contributions. Ambient particle-bound PAHs of molecular weight 168-266 were enriched by 1.5 to 3.5 times during the coal-fired power plant operational period. However, further investigation is needed to determine the relative contribution from residential and utility coal combustion and vehicular activities.« less

Microstructure optimization for high-performance PrBa0.5Sr0.5Co1.5Fe0.5O5+δ-La2NiO4+δ core-shell cathode of solid oxide fuel cells

NASA Astrophysics Data System (ADS)

Li, Jin; Qiu, Peng; Xia, Meng; Jia, Lichao; Chi, Bo; Pu, Jian; Li, Jian

2018-03-01

Four PrBa0.5Sr0.5Co1.5Fe0.5O5+δ (PBSCF)-La2NiO4+δ (LN) core-shell cathodes, designated as PL-0, PL-1, PL-3 and PL-5, are prepared by infiltrating LN solution into PBSCF scaffold, and they are investigated in terms of the effect of LN thickness on their electrochemical performance. PL-3 with a continuous LN coating of a moderate average thickness (∼9 nm) demonstrates the lowest initial polarization resistance (0.51 Ω cm2) and highest power density (0.71 W cm-2) among all the cathodes. Polarized at 400 mA cm-2 and 700 °C for up to 40 h, the polarization resistance of all the prepared cathodes increases to approach a stable level after early stage decrease due to current activation, and PL-3 exhibits a slower average rate of performance degradation (25%). The electrochemical performance improvement is mainly attributed to that LN has a relatively high oxygen surface exchange coefficient and continuous LN coating depresses Sr segregation at PBSCF/LN interface.

Fundamental formulae for wave-energy conversion

PubMed Central

Falnes, Johannes; Kurniawan, Adi

2015-01-01

The time-average wave power that is absorbed from an incident wave by means of a wave-energy conversion (WEC) unit, or by an array of WEC units—i.e. oscillating immersed bodies and/or oscillating water columns (OWCs)—may be mathematically expressed in terms of the WEC units' complex oscillation amplitudes, or in terms of the generated outgoing (diffracted plus radiated) waves, or alternatively, in terms of the radiated waves alone. Following recent controversy, the corresponding three optional expressions are derived, compared and discussed in this paper. They all provide the correct time-average absorbed power. However, only the first-mentioned expression is applicable to quantify the instantaneous absorbed wave power and the associated reactive power. In this connection, new formulae are derived that relate the ‘added-mass’ matrix, as well as a couple of additional reactive radiation-parameter matrices, to the difference between kinetic energy and potential energy in the water surrounding the immersed oscillating WEC array. Further, a complex collective oscillation amplitude is introduced, which makes it possible to derive, by a very simple algebraic method, various simple expressions for the maximum time-average wave power that may be absorbed by the WEC array. The real-valued time-average absorbed power is illustrated as an axisymmetric paraboloid defined on the complex collective-amplitude plane. This is a simple illustration of the so-called ‘fundamental theorem for wave power’. Finally, the paper also presents a new derivation that extends a recently published result on the direction-average maximum absorbed wave power to cases where the WEC array's radiation damping matrix may be singular and where the WEC array may contain OWCs in addition to oscillating bodies. PMID:26064612

Harnessing Solar Energy Using Photosynthetic and Organic Pigments

NASA Astrophysics Data System (ADS)

Fitzsimons, Toby Ryan

Fossil fuels are a finite energy resource that must be supplemented or replaced by more stable forms of electrical energy. Solar technology research strives to supplement and provide eventual replacement for fossil fuel technology. This experiment focused on the use of natural pigments as photo-sensitizers in the current generation of solar cells called dye sensitized solar cells (DSSCs). Pigments from purified chlorophyll a, chlorophyll b, chlorophyll a/b, crude spinach (Spinacia oleracea) extract, phycocyanin, and chlorophyllin were used to construct DSSCs and evaluated, along with a control containing no pigment, for solar energy conversion. The anode of the solar cells consisted of titanium dioxide (TiO2) plates soaked in pigment solutions for twenty-four hours. The plates were assembled, along with an electrolyte sandwiched between cells, and a platinum-coated counter plate that functioned as the cathode. A gasket seal was placed between the plates and held together with rubber bands. The DSSCs were each tested for a maximum power (Pmax) point and a resistor was selected that corresponded to the resistance at that point. The cells were randomly placed into a power block assembly located in an environmental chamber with lighting that provided an average of 27,590 lumens at the surface of DSSCs. With appropriate resistors in place, the cells were subjected to twelve-hour days and twelve-hour nights for ten days, and measurements were recorded every ten minutes. Data were collected to obtain values for voltage in millivolts (mV), current in microamps (microA), and power in microwatts (microW), as well as beginning and ending efficiencies in converting light to usable energy. Voltages were substantially higher during the day than at night for all pigments, except for the control, indicating that the pigments functioned as DSSCs. Hence, only daytime values were used for data analysis. Voltage during the ten-day experiment ranged from 3.99 to 274 mV; current ranged from 0.0180 to 41.9 microA, and power ranged from 0.00 to 11.3 microW. Chlorophyllin had the highest peak and least voltage (274 and 161 mV), highest peak and least current (41.9 and 21.8 microA), and highest peak and least power (11.3 and 4.84 microW). The ranking of the pigments for peak voltage was: Chlorophyllin = Crude Extract ≥ Chlorophyll a = Chlorophyll a/b ≥ Phycocyanin = Chlorophyll b > Control. The ranking for least voltage was: Chlorophyllin > Phycocyanin ≥ Chlorophyll a/b ≥ Crude Extract ≥ Chlorophyll b ≥ Chlorophyll a ≥ Control. Ranking for peak and least values were similar for current and power. Solar energy conversion (efficiency in converting light energy to usable energy in watts per square meter) for all treatments ranged from 0.000595 to 0.0217% at the beginning of the experiment, and was highest in cells constructed with chlorophyllin. Based on rankings from peak and ending voltage values, as well as other measurements, it was concluded that DSSCs constructed with chlorophyllin performed the best and lasted the longest as photo-sensitizers, compared to other pigments used in this investigation. The DSSCs constructed with crude extract performed almost as well as those constructed with chlorophyllin at the beginning of the experiment, but degradation of this naturally-made pigment may have prevented these cells from sustaining solar energy conversion for more than a few days. Other pigments demonstrated conversion values higher than those of control DSSCs which contained no pigments. The results from this project provide evidence that DSSCs can produce useable energy. More research is needed to enhance and prolong the efficiency of DSSCs in solar energy conversion.

Comparative study of plasma-deposited fluorocarbon coatings on different substrates

NASA Astrophysics Data System (ADS)

Farsari, E.; Kostopoulou, M.; Amanatides, E.; Mataras, D.; Rapakoulias, D. E.

2011-05-01

The deposition of hydrophobic fluorocarbon coatings from C2F6 and C2F6-H2 rf discharges on different substrates was examined. Polyester textile, glass and two different ceramic compounds were used as substrates. The effect of the total gas pressure, the rf power dissipation and the deposition time on the hydrophobic character of the samples was investigated. Films deposited on polyester textiles at low pressure (0.03 mbar) and power consumption (16 mW cm-2) using pure C2F6 presented the highest water contact angles (~150°). On the other hand, the addition of hydrogen was necessary in order to deposit stable hydrophobic coatings on glass and ceramic substrates. Coatings deposited on glass at intermediate deposition rates (~100 Å min-1) and pressures presented the highest angles (~105°). Concerning the heavy clay ceramics, samples treated in low-pressure (0.05 mbar) and low-power (16 mW cm-2) discharges showed the highest contact angles. The deposition time was found to play an important role in the hydrophobicity and long-term behaviour of porous and rough substrates.

Steady-State Thermal-Hydraulics Analyses for the Conversion of BR2 to Low Enriched Uranium Fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Licht, J.; Bergeron, A.; Dionne, B.

The code PLTEMP/ANL version 4.2 was used to perform the steady-state thermal-hydraulic analyses of the BR2 research reactor for conversion from Highly-Enriched to Low Enriched Uranium fuel (HEU and LEU, respectively). Calculations were performed to evaluate different fuel assemblies with respect to the onset of nucleate boiling (ONB), flow instability (FI), critical heat flux (CHF) and fuel temperature at beginning of cycle conditions. The fuel assemblies were characteristic of fresh fuel (0% burnup), highest heat flux (16% burnup), highest power (32% burnup) and highest burnup (46% burnup). Results show that the high heat flux fuel element is limiting for ONB,more » FI, and CHF, for both HEU and LEU fuel, but that the high power fuel element produces similar margin in a few cases. The maximum fuel temperature similarly occurs in both the high heat flux and high power fuel assemblies for both HEU and LEU fuel. A sensitivity study was also performed to evaluate the variation in fuel temperature due to uncertainties in the thermal conductivity degradation associated with burnup.« less

Signal voter

DOEpatents

Goodwin, Roy L.

1981-01-01

A voter for providing a single accurate output signal that is derived from the closest two signal levels of three input signals, each of which signals represents a measurement of the same phenomena. By means of the voting circuit, the signals are first sorted by level of amplitude and then ranked as highest, middle or lowest. The highest or lowest signal that is furthest from the middle signal is rejected, while the other highest or lowest signal is selected for processing. The selected high or low signal is then averaged with the middle signal to provide the output signal.

Environmental effects of interstate power trading on electricity consumption mixes.

PubMed

Marriott, Joe; Matthews, H Scott

2005-11-15

Although many studies of electricity generation use national or state average generation mix assumptions, in reality a great deal of electricity is transferred between states with very different mixes of fossil and renewable fuels, and using the average numbers could result in incorrect conclusions in these studies. We create electricity consumption profiles for each state and for key industry sectors in the U.S. based on existing state generation profiles, net state power imports, industry presence by state, and an optimization model to estimate interstate electricity trading. Using these "consumption mixes" can provide a more accurate assessment of electricity use in life-cycle analyses. We conclude that the published generation mixes for states that import power are misleading, since the power consumed in-state has a different makeup than the power that was generated. And, while most industry sectors have consumption mixes similar to the U.S. average, some of the most critical sectors of the economy--such as resource extraction and material processing sectors--are very different. This result does validate the average mix assumption made in many environmental assessments, but it is important to accurately quantify the generation methods for electricity used when doing life-cycle analyses.

Adult physiological response to infant cries: effects of temperament of infant, parental status, and gender.

PubMed

Boukydis, C F; Burgess, R L

1982-10-01

This article describes research on adult physiological and self-report response to audiotapes of infants' cries. 3 groups were studied: nonparents, primiparous parents, and multiparous parents. The tapes consisted of cries ordered (difficult, average, easy) according to sound spectrographic features and infant temperament ratings. While nonparents and multiparous parents showed the expected order in arousal levels (difficult infant cries highest, easy infant cries lowest), primiparous parents had highest levels to average infant cries. Overall, primiparous parents had highest levels of arousal, nonparents next, and multiparous parents least. There were no gender differences in arousal. Difficult infant cries received higher irritation and spoiled ratings; were rated as more grating, arousing, piercing, etc.; were less similar to own infants' cries; and were said to be caused more frequently by frustration, etc., rather than routine physical discomfort. Fathers had higher irritation and spoiled ratings, and lower care for ratings, than mothers. The relationship of these data to own infant temperament ratings was also assessed.

SELF BLOOD GLUCOSE MONITORING UNDERESTIMATES HYPERGLYCEMIA AND HYPOGLYCEMIA AS COMPARED TO CONTINUOUS GLUCOSE MONITORING IN TYPE 1 AND TYPE 2 DIABETES.

PubMed

Mangrola, Devna; Cox, Christine; Furman, Arianne S; Krishnan, Sridevi; Karakas, Sidika E

2018-01-01

When glucose records from self blood glucose monitoring (SBGM) do not reflect estimated average glucose from glycosylated hemoglobin (HgBA1) or when patients' clinical symptoms are not explained by their SBGM records, clinical management of diabetes becomes a challenge. Our objective was to determine the magnitude of differences in glucose values reported by SBGM versus those documented by continuous glucose monitoring (CGM). The CGM was conducted by a clinical diabetes educator (CDE)/registered nurse by the clinic protocol, using the Medtronic iPRO2 ™ system. Patients continued SBGM and managed their diabetes without any change. Data from 4 full days were obtained, and relevant clinical information was recorded. De-identified data sets were provided to the investigators. Data from 61 patients, 27 with type 1 diabetes (T1DM) and 34 with T2DM were analyzed. The lowest, highest, and average glucose recorded by SBGM were compared to the corresponding values from CGM. The lowest glucose values reported by SBGM were approximately 25 mg/dL higher in both T1DM ( P = .0232) and T2DM ( P = .0003). The highest glucose values by SBGM were approximately 30 mg/dL lower in T1DM ( P = .0005) and 55 mg/dL lower in T2DM ( P<.0001). HgBA1c correlated with the highest and average glucose by SBGM and CGM. The lowest glucose values were seen most frequently during sleep and before breakfast; the highest were seen during the evening and postprandially. SBGM accurately estimates the average glucose but underestimates glucose excursions. CGM uncovers glucose patterns that common SBGM patterns cannot. CDE = certified diabetes educator; CGM = continuous glucose monitoring; HgBA1c = glycosylated hemoglobin; MAD = mean absolute difference; SBGM = self blood glucose monitoring; T1DM = type 1 diabetes; T2DM = type 2 diabetes.

The first countrywide monitoring of selected POPs: Polychlorinated biphenyls (PCBs), polybrominated diphenyl ethers (PBDEs) and selected organochlorine pesticides (OCPs) in the atmosphere of Turkey

NASA Astrophysics Data System (ADS)

Kurt-Karakus, Perihan Binnur; Ugranli-Cicek, Tugba; Sofuoglu, Sait C.; Celik, Halil; Gungormus, Elif; Gedik, Kadir; Sofuoglu, Aysun; Okten, Hatice Eser; Birgul, Askın; Alegria, Henry; Jones, Kevin C.

2018-03-01

Atmospheric levels of 43 PCBs, 22 OCPs, and 14 PBDEs were determined in 16 cities at urban and rural sites by passive sampling to generate the first large-scale nationwide dataset of POP residues in Turkey's atmosphere. Sampling campaign was performed from May 2014 to April 2015 with three-month sampling periods at locations on east-west and north-south transects through the country to investigate seasonal and spatial variations, including long range atmospheric transport (LRAT). Factor analysis was conducted to infer on the potential sources. Overall average Σ43PCBs concentration was 108 ± 132 pg/m3. PCB-118 (26.3 ± 44.6 pg/m3) was the top congener, and penta-CBs had the highest contribution with 54.3%. ΣDDTs had the highest annual mean concentration with 134 ± 296 pg/m3 among the OCP groups among which the highest concentration compound was p'p-DDE (97.6 ± 236 pg/m3). Overall average concentration of Σ14PBDEs was 191 ± 329 pg/m3 with the highest contribution from BDE-190 (42%). Comparison of OCPs and PCBs concentrations detected at temperatures which were above and below annual average temperature indicated higher concentrations in the warmer periods, hence significance of secondary emissions for several OCPs and Σ43PCBs, as well as inference as LRAT from secondary emissions. The first nationwide POPs database constructed in this study, point to current use, local secondary emissions, and LRAT for different individual compounds, and indicate the need for regular monitoring.

Grid regulation services for energy storage devices based on grid frequency

DOEpatents

Pratt, Richard M; Hammerstrom, Donald J; Kintner-Meyer, Michael C.W.; Tuffner, Francis K

2013-07-02

Disclosed herein are representative embodiments of methods, apparatus, and systems for charging and discharging an energy storage device connected to an electrical power distribution system. In one exemplary embodiment, a controller monitors electrical characteristics of an electrical power distribution system and provides an output to a bi-directional charger causing the charger to charge or discharge an energy storage device (e.g., a battery in a plug-in hybrid electric vehicle (PHEV)). The controller can help stabilize the electrical power distribution system by increasing the charging rate when there is excess power in the electrical power distribution system (e.g., when the frequency of an AC power grid exceeds an average value), or by discharging power from the energy storage device to stabilize the grid when there is a shortage of power in the electrical power distribution system (e.g., when the frequency of an AC power grid is below an average value).

Grid regulation services for energy storage devices based on grid frequency

DOEpatents

Pratt, Richard M.; Hammerstrom, Donald J.; Kintner-Meyer, Michael C. W.; Tuffner, Francis K.

2017-09-05

Disclosed herein are representative embodiments of methods, apparatus, and systems for charging and discharging an energy storage device connected to an electrical power distribution system. In one exemplary embodiment, a controller monitors electrical characteristics of an electrical power distribution system and provides an output to a bi-directional charger causing the charger to charge or discharge an energy storage device (e.g., a battery in a plug-in hybrid electric vehicle (PHEV)). The controller can help stabilize the electrical power distribution system by increasing the charging rate when there is excess power in the electrical power distribution system (e.g., when the frequency of an AC power grid exceeds an average value), or by discharging power from the energy storage device to stabilize the grid when there is a shortage of power in the electrical power distribution system (e.g., when the frequency of an AC power grid is below an average value).

Grid regulation services for energy storage devices based on grid frequency

DOEpatents

Pratt, Richard M; Hammerstrom, Donald J; Kintner-Meyer, Michael C.W.; Tuffner, Francis K

2014-04-15

Disclosed herein are representative embodiments of methods, apparatus, and systems for charging and discharging an energy storage device connected to an electrical power distribution system. In one exemplary embodiment, a controller monitors electrical characteristics of an electrical power distribution system and provides an output to a bi-directional charger causing the charger to charge or discharge an energy storage device (e.g., a battery in a plug-in hybrid electric vehicle (PHEV)). The controller can help stabilize the electrical power distribution system by increasing the charging rate when there is excess power in the electrical power distribution system (e.g., when the frequency of an AC power grid exceeds an average value), or by discharging power from the energy storage device to stabilize the grid when there is a shortage of power in the electrical power distribution system (e.g., when the frequency of an AC power grid is below an average value).

Point-ahead limitation on reciprocity tracking. [in earth-space optical link

NASA Technical Reports Server (NTRS)

Shapiro, J. H.

1975-01-01

The average power received at a spacecraft from a reciprocity-tracking transmitter is shown to be the free-space diffraction-limited result times a gain-reduction factor that is due to the point-ahead requirement. For a constant-power transmitter, the gain-reduction factor is approximately equal to the appropriate spherical-wave mutual-coherence function. For a constant-average-power transmitter, an exact expression is obtained for the gain-reduction factor.

Output power distributions of terminals in a 3G mobile communication network.

PubMed

Persson, Tomas; Törnevik, Christer; Larsson, Lars-Eric; Lovén, Jan

2012-05-01

The objective of this study was to examine the distribution of the output power of mobile phones and other terminals connected to a 3G network in Sweden. It is well known that 3G terminals can operate with very low output power, particularly for voice calls. Measurements of terminal output power were conducted in the Swedish TeliaSonera 3G network in November 2008 by recording network statistics. In the analysis, discrimination was made between rural, suburban, urban, and dedicated indoor networks. In addition, information about terminal output power was possible to collect separately for voice and data traffic. Information from six different Radio Network Controllers (RNCs) was collected during at least 1 week. In total, more than 800000 h of voice calls were collected and in addition to that a substantial amount of data traffic. The average terminal output power for 3G voice calls was below 1 mW for any environment including rural, urban, and dedicated indoor networks. This is <1% of the maximum available output power. For data applications the average output power was about 6-8 dB higher than for voice calls. For rural areas the output power was about 2 dB higher, on average, than in urban areas. Copyright © 2011 Wiley Periodicals, Inc.

49 CFR 250.5 - General instructions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... to the effect that he is familiar with the corporate powers of the carrier applicant and the orders... obligations of the Trustee will be treated as an expense of administration and receive the highest lien on the... be treated as an expense of administration and receive the highest lien on the railroad's property...

47 CFR 15.403 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... or below its maximum level. (p) Pulse. A pulse is a continuous transmission of a sequence of... bridge in a peer-to-peer connection or as a connector between the wired and wireless segments of the... the presence of a radar. (c) Average Symbol Envelope Power. The average symbol envelope power is the...

Nonimaging concentrators for diode-pumped slab lasers

NASA Astrophysics Data System (ADS)

Lacovara, Philip; Gleckman, Philip L.; Holman, Robert L.; Winston, Roland

1991-10-01

Diode-pumped slab lasers require concentrators for high-average power operation. We detail the properties of diode lasers and slab lasers which set the concentration requirements and the concentrator design methodologies that are used, and describe some concentrator designs used in high-average power slab lasers at Lincoln Laboratory.

Energy production estimation for Kosh-Agach grid-tie photovoltaic power plant for different photovoltaic module types

NASA Astrophysics Data System (ADS)

Gabderakhmanova, T. S.; Kiseleva, S. V.; Frid, S. E.; Tarasenko, A. B.

2016-11-01

This paper is devoted to calculation of yearly energy production, demanded area and capital costs for first Russian 5 MW grid-tie photovoltaic (PV) plant in Altay Republic that is named Kosh-Agach. Simple linear calculation model, involving average solar radiation and temperature data, grid-tie inverter power-efficiency dependence and PV modules parameters is proposed. Monthly and yearly energy production, equipment costs and demanded area for PV plant are estimated for mono-, polycrystalline and amorphous modules. Calculation includes three types of initial radiation and temperature data—average day for every month from NASA SSE, average radiation and temperature for each day of the year from NASA POWER and typical meteorology year generated from average data for every month. The peculiarities for each type of initial data and their influence on results are discussed.

Average BER analysis of SCM-based free-space optical systems by considering the effect of IM3 with OSSB signals under turbulence channels.

PubMed

Lim, Wansu; Cho, Tae-Sik; Yun, Changho; Kim, Kiseon

2009-11-09

In this paper, we derive the average bit error rate (BER) of subcarrier multiplexing (SCM)-based free space optics (FSO) systems using a dual-drive Mach-Zehnder modulator (DD-MZM) for optical single-sideband (OSSB) signals under atmospheric turbulence channels. In particular, we consider the third-order intermodulation (IM3), a significant performance degradation factor, in the case of high input signal power systems. The derived average BER, as a function of the input signal power and the scintillation index, is employed to determine the optimum number of SCM users upon the designing FSO systems. For instance, when the user number doubles, the input signal power decreases by almost 2 dBm under the log-normal and exponential turbulence channels at a given average BER.

Depth distribution of microbial production and oxidation of methane in northern boreal peatlands.

PubMed

Sundh, I; Nilsson, M; Granberg, G; Svensson, B H

1994-05-01

The depth distributions of anaerobic microbial methane production and potential aerobic microbial methane oxidation were assessed at several sites in both Sphagnum- and sedge-dominated boreal peatlands in Sweden, and compared with net methane emissions from the same sites. Production and oxidation of methane were measured in peat slurries, and emissions were measured with the closed-chamber technique. Over all eleven sites sampled, production was, on average, highest 12 cm below the depth of the average water table. On the other hand, highest potential oxidation of methane coincided with the depth of the average water table. The integrated production rate in the 0-60 cm interval ranged between 0.05 and 1.7 g CH4 m (-2) day(-) and was negatively correlated with the depth of the average water table (linear regression: r (2) = 0.50, P = 0.015). The depth-integrated potential CH4-oxidation rate ranged between 3.0 and 22.1 g CH4 m(-2) day(-1) and was unrelated to the depth of the average water table. A larger fraction of the methane was oxidized at sites with low average water tables; hence, our results show that low net emission rates in these environments are caused not only by lower methane production rates, but also by conditions more favorable for the development of CH4-oxidizing bacteria in these environments.

Electric vehicle drive systems

NASA Astrophysics Data System (ADS)

Appleyard, M.

1992-01-01

New legislation in the State of California requires that 2% of vehicles sold there from 1998 will be 'zero-emitting'. This provides a unique market opportunity for developers of electric vehicles but substantial improvements in the technology are probably required if it is to be successfully exploited. There are around a dozen types of battery that are potentially relevant to road vehicles but, at the present, lead/acid and sodium—sulphur come closest to combining acceptable performance, life and cost. To develop an efficient, lightweight electric motor system requires up-to-date techniques of magnetics design, and the latest power-electronic and microprocessor control methods. Brushless machines, coupled with solid-state inverters, offer the most economical solution for mass production, even though their development costs are higher than for direct-current commutator machines. Fitted to a small car, even the highest energy-density batteries will only provide around 200 km average range before recharging. Therefore, some form of supplementary on-board power generation will probably be needed to secure widespread acceptance by the driving public. Engine-driven generators of quite low power can achieve useful increases in urban range but will fail to qualify as 'zero-emitting'. On the other hand, if the same function could be economically performed by a small fuel-cell using hydrogen derived from a methanol reformer, then most of the flexibility provided by conventional vehicles would be retained. The market prospects for electric cars would then be greatly enhanced and their dependence on very advanced battery technology would be reduced.

Associations Between Balance and Muscle Strength, Power Performance in Male Youth Athletes of Different Maturity Status.

PubMed

Hammami, Raouf; Chaouachi, Anis; Makhlouf, Issam; Granacher, Urs; Behm, David G

2016-11-01

Balance, strength and power relationships may contain important information at various maturational stages to determine training priorities. The objective was to examine maturity-specific relationships of static/dynamic balance with strength and power measures in young male athletes. Soccer players (N = 130) aged 10-16 were assessed with the Stork and Y balance (YBT) tests. Strength/power measures included back extensor muscle strength, standing long jump (SLJ), countermovement jump (CMJ), and 3-hop jump tests. Associations between balance with strength/power variables were calculated according to peak-height-velocity (PHV). There were significant medium-large sized correlations between all balance measures with back extensor strength (r = .486-.791) and large associations with power (r = .511-.827). These correlation coefficients were significantly different between pre-PHV and circa PHV as well as pre-PHV and post-PHV with larger associations in the more mature groups. Irrespective of maturity-status, SLJ was the best strength/power predictor with the highest proportion of variance (12-47%) for balance (i.e., Stork eyes opened) and the YBT was the best balance predictor with the highest proportion of variance (43-78%) for all strength/power variables. The associations between balance and muscle strength/power measures in youth athletes that increase with maturity may imply transfer effects from balance to strength/power training and vice versa in youth athletes.

Discussions On Worst-Case Test Condition For Single Event Burnout

NASA Astrophysics Data System (ADS)

Liu, Sandra; Zafrani, Max; Sherman, Phillip

2011-10-01

This paper discusses the failure characteristics of single- event burnout (SEB) on power MOSFETs based on analyzing the quasi-stationary avalanche simulation curves. The analyses show the worst-case test condition for SEB would be using the ion that has the highest mass that would result in the highest transient current due to charge deposition and displacement damage. The analyses also show it is possible to build power MOSFETs that will not exhibit SEB even when tested with the heaviest ion, which have been verified by heavy ion test data on SEB sensitive and SEB immune devices.

Study on Safety Monitoring System for Submarine Power Cable on the Basis of AIS and Radar Technology

NASA Astrophysics Data System (ADS)

Jie, Wang; Yao-Tian, Fan

Through analyzing the risks of submarine power cable, the highest risk to damage the cable identified is from ship. Based on concept of Vessel Traffic Management Information Systems, the three core sub-systems of safety monitoring system for submarine power cable were studied and described, also some suggestions were given.

Phytoplankton Abundance and Contributions to Suspended Particulate Matter in the Ohio, Upper Mississippi and Missouri Rivers.

EPA Science Inventory

A survey of the Ohio, Missouri and Upper Mississippi Rivers revealed large (five-fold) differences in summer average chlorophyll a (CHLa). Average concentrations were highest in the Mississippi (32.3 + 1.8 µg L-1) with lower values in the Missouri (19.7 + 1.1 µg L-1) and Ohio (6...

75 FR 46952 - Prescription Drug User Fee Rates for Fiscal Year 2011

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-04

... average change in pay per FTE (4.53 percent) is the highest of the three factors, it becomes the inflation... pay change for the previous fiscal year for Federal employees stationed in the Washington, DC metropolitan area; or (3) the average annual change in cost, per full time equivalent (FTE) FDA position, of...

High-Achieving and Average Students' Reading Growth: Contrasting School and Summer Trajectories

ERIC Educational Resources Information Center

Rambo-Hernandez, Karen E.; McCoach, D. Betsy

2015-01-01

Much is unknown about how initially high-achieving students grow academically, especially given the measurement issues inherent in assessing growth for the highest performing students. This study compared initially high-achieving and average students' growth in reading (in a cohort of third-grade students from 2,000 schools) over 3 years.…

High-Power Hall Thruster Technology Evaluated for Primary Propulsion Applications

NASA Technical Reports Server (NTRS)

Manzella, David H.; Jankovsky, Robert S.; Hofer, Richard R.

2003-01-01

High-power electric propulsion systems have been shown to be enabling for a number of NASA concepts, including piloted missions to Mars and Earth-orbiting solar electric power generation for terrestrial use (refs. 1 and 2). These types of missions require moderate transfer times and sizable thrust levels, resulting in an optimized propulsion system with greater specific impulse than conventional chemical systems and greater thrust than ion thruster systems. Hall thruster technology will offer a favorable combination of performance, reliability, and lifetime for such applications if input power can be scaled by more than an order of magnitude from the kilowatt level of the current state-of-the-art systems. As a result, the NASA Glenn Research Center conducted strategic technology research and development into high-power Hall thruster technology. During program year 2002, an in-house fabricated thruster, designated the NASA-457M, was experimentally evaluated at input powers up to 72 kW. These tests demonstrated the efficacy of scaling Hall thrusters to high power suitable for a range of future missions. Thrust up to nearly 3 N was measured. Discharge specific impulses ranged from 1750 to 3250 sec, with discharge efficiencies between 46 and 65 percent. This thruster is the highest power, highest thrust Hall thruster ever tested.

Fiber-based tunable repetition rate source for deep tissue two-photon fluorescence microscopy

PubMed Central

Charan, Kriti; Li, Bo; Wang, Mengran; Lin, Charles P.; Xu, Chris

2018-01-01

Deep tissue multiphoton imaging requires high peak power to enhance signal and low average power to prevent thermal damage. Both goals can be advantageously achieved through laser repetition rate tuning instead of simply adjusting the average power. We show that the ideal repetition rate for deep two-photon imaging in the mouse brain is between 1 and 10 MHz, and we present a fiber-based source with an arbitrarily tunable repetition rate within this range. The performance of the new source is compared to a mode-locked Ti:Sapphire (Ti:S) laser for in vivo imaging of mouse brain vasculature. At 2.5 MHz, the fiber source requires 5.1 times less average power to obtain the same signal as a standard Ti:S laser operating at 80 MHz. PMID:29760989

Survey of U.S. Ancillary Services Markets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Zhi; Levin, Todd; Conzelmann, Guenter

In addition to providing energy to end-consumers, power system operators are also responsible for ensuring system reliability. To this end, power markets maintain an array of ancillary services to ensure that it is always possible to balance the supply and demand for energy in real-time. A subset of these ancillary services are commonly procured through market-based mechanisms: namely, Regulation, Spinning, and Non-spinning Reserves. Regulation Reserves are maintained to respond to supply/demand imbalances over short time frames, typically on the order of several seconds to one minute. Resources that provide Regulation Reserves adjust their generation or load levels in response tomore » automatic generation control (AGC) signals provided by the system operator. Contingency reserves are maintained to provide additional generation capacity in the event that load increases substantially or supply side resources reduce their output or are taken offline. The reserves are typically segmented into two categories, 1) Spinning or Synchronized Reserves that are provided by generation units that are actively generating and have the ability to increase or decrease their output, 2) Non-spinning or Non-synchronized Reserves that are provided by generation resources that are not actively generating, but are able to start up and provide generation within a specified timeframe. Contingency reserves typically have response times on the order of ten to 30 minutes and can also be provided by demand-side resources that are capable of reducing their load. There are seven distinct power markets in the United States, each operated by a Regional Transmission Operator (RTO) or Independent System Operator (ISO) that operates the transmission system in its territory, operates markets for energy and ancillary services, and maintains system reliability. Each power market offers its own set of ancillary services, and precise definitions, requirements, and market mechanisms differ between markets. Despite the differences between markets, both in terms of services offered and system requirements, some broad trends generally apply. Regulation Reserves typically have the highest market prices, followed by Spinning Reserves and Non-spinning Reserves. Prices for Regulation Reserves have been the highest in the PJM market, since it opened in October 2012. This is partially because PJM experienced large price spikes during the period of extreme weather conditions in early 2014. ERCOT has traditionally had the highest prices for Spinning Reserves (called Responsive Reserves in ERCOT), including several periods of sustained high prices between 2010 and 2012. This can be explained in part by the relatively high penetration of variable wind resources and a similarly high requirement relative to peak load. ERCOT has also traditionally had the highest price for Non-spinning Reserves, followed by the NYISO East region. Both have experienced several periods of prolonged high prices since their inception, an occurrence that has not been regularly seen in other markets. In ISO-NE and PJM for example, the market clearing price for Non-spinning Reserves is typically $0/MWh more than 95% of the time. Market volume (in terms of the average amount of capacity of each service that is provided to a system) typically follows the reverse order of prices, as systems maintain the most Non-spinning Reserves capacity followed by Spinning Reserves and Regulation Reserves. PJM generally has the largest market for Regulation Reserves both in terms of capacity. The size of most Regulation Reserves markets in terms of capacity stay relatively constant year-to-year, as this is dictated largely by system requirements. PJM also generally has the largest Spinning Reserves market in terms of capacity. SPP, MISO, ISO-NE and SPP (beginning in 2014) all have Spinning Reserve markets with similar average capacity levels. When combined, the markets for Non-spinning and Operating reserves in ISO-NE have a comparable capacity to the market for Primary Reserves 1 in PJM. SPP, MISO, and CAISO all have smaller markets for their respective Non-spinning Reserves products that are roughly the same size as each other in terms of capacity.« less

High-power picosecond laser with 400W average power for large scale applications

NASA Astrophysics Data System (ADS)

Du, Keming; Brüning, Stephan; Gillner, Arnold

2012-03-01

Laser processing is generally known for low thermal influence, precise energy processing and the possibility to ablate every type of material independent on hardness and vaporisation temperature. The use of ultra-short pulsed lasers offers new possibilities in the manufacturing of high end products with extra high processing qualities. For achieving a sufficient and economical processing speed, high average power is needed. To scale the power for industrial uses the picosecond laser system has been developed, which consists of a seeder, a preamplifier and an end amplifier. With the oscillator/amplifier system more than 400W average power and maximum pulse energy 1mJ was obtained. For study of high speed processing of large embossing metal roller two different ps laser systems have been integrated into a cylinder engraving machine. One of the ps lasers has an average power of 80W while the other has 300W. With this high power ps laser fluencies of up to 30 J/cm2 at pulse repetition rates in the multi MHz range have been achieved. Different materials (Cu, Ni, Al, steel) have been explored for parameters like ablation rate per pulse, ablation geometry, surface roughness, influence of pulse overlap and number of loops. An enhanced ablation quality and an effective ablation rate of 4mm3/min have been achieved by using different scanning systems and an optimized processing strategy. The max. achieved volume rate is 20mm3/min.

Continuous-wave and quasi-continuous wave thulium-doped all-fiber laser: implementation on kidney stone fragmentations.

PubMed

Pal, Debasis; Ghosh, Aditi; Sen, Ranjan; Pal, Atasi

2016-08-10

A continuous-wave (CW) as well as quasi-continuous wave (QCW) thulium-doped all-fiber laser at 1.94 μm has been designed for targeting applications in urology. The thulium-doped active fiber with an octagonal-shaped inner cladding is pumped at 793 nm to achieve stable CW laser power of 10 W with 32% lasing efficiency (against launched pump power). The linear variation of laser power with pump offers a scope of further power scaling. A QCW operation with variation of duty cycle from 0.5% to 90%, repetition rate from 0.1 Hz to 1 kHz, and pulse width from 40 μs to 2 s has been presented. Laser power of 9.5 W in CW mode of operation and average power of 5.2 W with energy range of 10.4-104 mJ in QCW mode of operation has been employed to fragment calcium oxalate monohydrate kidney stones (size of 1.5-4 cm) having different colors and composition. Dependence of ablation threshold, ablation rate, and average fragmented particle size on the average power and energy has been studied. One minute of laser exposure results in fragmentation of a stone surface with ablation rate of 8  mg/min having minimum particle size of 6.54 μm with an average size of 20-100 μm ensuring the natural removal of fragmented parts through the urethra.

Aerodynamic performance of two-dimensional, chordwise flexible flapping wings at fruit fly scale in hover flight.

PubMed

Sridhar, Madhu; Kang, Chang-kwon

2015-05-06

Fruit flies have flexible wings that deform during flight. To explore the fluid-structure interaction of flexible flapping wings at fruit fly scale, we use a well-validated Navier-Stokes equation solver, fully-coupled with a structural dynamics solver. Effects of chordwise flexibility on a two dimensional hovering wing is studied. Resulting wing rotation is purely passive, due to the dynamic balance between aerodynamic loading, elastic restoring force, and inertial force of the wing. Hover flight is considered at a Reynolds number of Re = 100, equivalent to that of fruit flies. The thickness and density of the wing also corresponds to a fruit fly wing. The wing stiffness and motion amplitude are varied to assess their influences on the resulting aerodynamic performance and structural response. Highest lift coefficient of 3.3 was obtained at the lowest-amplitude, highest-frequency motion (reduced frequency of 3.0) at the lowest stiffness (frequency ratio of 0.7) wing within the range of the current study, although the corresponding power required was also the highest. Optimal efficiency was achieved for a lower reduced frequency of 0.3 and frequency ratio 0.35. Compared to the water tunnel scale with water as the surrounding fluid instead of air, the resulting vortex dynamics and aerodynamic performance remained similar for the optimal efficiency motion, while the structural response varied significantly. Despite these differences, the time-averaged lift scaled with the dimensionless shape deformation parameter γ. Moreover, the wing kinematics that resulted in the optimal efficiency motion was closely aligned to the fruit fly measurements, suggesting that fruit fly flight aims to conserve energy, rather than to generate large forces.

Variation in Weed Seed Fate Fed to Different Holstein Cattle Groups.

PubMed

Rahimi, Salman; Mashhadi, Hamid Rahimian; Banadaky, Mehdi Dehghan; Mesgaran, Mohsen Beheshtian

2016-01-01

Weed seeds may maintain their viability when passing through the digestive tract of cattle and can be therefore dispersed by animal movement or the application of manure. Whether different cattle types of the same species can cause differential weed seed fate is largely unknown to us particularly under non-grazed systems similar to Holstein-Friesian dairy farming. We investigated the effect on the seed survival of four weed species in the digestive tracts of four groups of Holstein cattle: lactating cows, feedlot male calves, dry cows and growing heifers. The weed species used were Cuscuta campestris, Polygonum aviculare, Rumex crispus and Sorghum halepense. Cattle excretion was sampled for recovery and viability of seeds at four 24 hourly intervals after seed intake. The highest seed recovery occurred two days after seed intake in all cattle groups. Averaged over weed species, dry and lactating cows had the lowest and highest seed recovery of 36.4% and 74.4% respectively. No significant differences were observed in seed recovery of the four weed species when their seeds were fed to dry cows. Based on a power model fitted to seed viability data, the estimated time to 50% viability loss after seed intake, over all cattle groups ranged from 65 h (R. crispus) to 76 h (P. aviculare). Recovered seeds from the dung of feedlot male calves showed the highest mortality among cattle groups. Significant correlation was found between seed viability and ruminal pH (r = 0.86; P<0.05). This study shows that management programs aiming to minimize weed infestation caused by livestock should account for the variation amongst cattle groups in seed persistence. Our findings can be used as a guideline for evaluating the potential risk of the spread of weeds via the application of cattle manure.

Diamond Raman laser emitting at 1194, 1419, and 597 nm

NASA Astrophysics Data System (ADS)

Pashinin, V. P.; Ralchenko, V. G.; Bolshakov, A. P.; Ashkinazi, E. E.; Konov, V. I.

2018-03-01

A Raman laser based on a synthetic diamond crystal pumped by nanosecond pulses of a 1030-nm Yb : YAG laser and emitting in the IR region at the first and second Stokes wavelengths of 1194 and 1419 nm, respectively, was developed. The conversion efficiency was 34% with a slope efficiency of 50% and an average power of 1.1 W at a wavelength of 1194 nm; the average power at 1419 nm was 0.52 W. Frequency doubling of the first Stokes component in a nonlinear BBO crystal resulted in orange (597.3 nm) radiation with a pulse energy of 0.15 mJ, an average power of 0.22 W, and a maximum efficiency of 20%.

Enhanced Charge Extraction of Li-Doped TiO2 for Efficient Thermal-Evaporated Sb2S3 Thin Film Solar Cells

PubMed Central

Lan, Chunfeng; Luo, Jingting; Lan, Huabin; Fan, Bo; Peng, Huanxin; Zhao, Jun; Sun, Huibin; Zheng, Zhuanghao; Liang, Guangxing; Fan, Ping

2018-01-01

We provided a new method to improve the efficiency of Sb2S3 thin film solar cells. The TiO2 electron transport layers were doped by lithium to improve their charge extraction properties for the thermal-evaporated Sb2S3 solar cells. The Mott-Schottky curves suggested a change of energy band and faster charge transport in the Li-doped TiO2 films. Compared with the undoped TiO2, Li-doped mesoporous TiO2 dramatically improved the photo-voltaic performance of the thermal-evaporated Sb2S3 thin film solar cells, with the average power conversion efficiency (PCE) increasing from 1.79% to 4.03%, as well as the improved open-voltage (Voc), short-circuit current (Jsc) and fill factors. The best device based on Li-doped TiO2 achieved a power conversion efficiency up to 4.42% as well as a Voc of 0.645 V, which are the highest values among the reported thermal-evaporated Sb2S3 solar cells. This study showed that Li-doping on TiO2 can effectively enhance the charge extraction properties of electron transport layers, offering a new strategy to improve the efficiency of Sb2S3-based solar cells. PMID:29495612

Pt and PtRu catalyst bilayers increase efficiencies for ethanol oxidation in proton exchange membrane electrolysis and fuel cells

NASA Astrophysics Data System (ADS)

Altarawneh, Rakan M.; Pickup, Peter G.

2017-10-01

Polarization curves, product distributions, and reaction stoichiometries have been measured for the oxidation of ethanol at anodes consisting of Pt and PtRu bilayers and a homogeneous mixture of the two catalysts. These anode structures all show synergies between the two catalysts that can be attributed to the oxidation of acetaldehyde produced at the PtRu catalyst by the Pt catalyst. The use of a PtRu layer over a Pt layer produces the strongest effect, with higher currents than a Pt on PtRu bilayer, mixed layer, or either catalyst alone, except for Pt at high potentials. Reaction stoichiometries (average number of electrons transferred per ethanol molecule) were closer to the values for Pt alone for both of the bilayer configurations but much lower for PtRu and mixed anodes. Although Pt alone would provide the highest overall fuel cell efficiency at low power densities, the PtRu on Pt bilayer would provide higher power densities without a significant loss of efficiency. The origin of the synergy between the Pt and PtRu catalysts was elucidated by separation of the total current into the individual components for generation of carbon dioxide and the acetaldehyde and acetic acid byproducts.

Effect of hang cleans or squats paired with countermovement vertical jumps on vertical displacement.

PubMed

Andrews, Tedi R; Mackey, Theresa; Inkrott, Thomas A; Murray, Steven R; Clark, Ida E; Pettitt, Robert W

2011-09-01

Complex training is characterized by pairing resistance exercise with plyometric exercise to exploit the postactivation potentiation (PAP) phenomenon, thereby promising a better training effect. Studies on PAP as measured by human power performances are equivocal. One issue may be the lack of analyses across multiple sets of paired exercises, a common practice used by athletes. We evaluated countermovement vertical jump (CMJ) performance in 19 women, collegiate athletes in 3 of the following trials: (a) CMJs-only, where 1 set of CMJs served as a conditioning exercise, (b) heavy-load, back squats paired with CMJs, and (c) hang cleans paired with CMJs. The CMJ vertical displacement (3-attempt average), as measured with digital video, served as the dependent variable of CMJ performance. Across 3 sets of paired-exercise regimens, CMJ-only depreciated 1.6 cm and CMJ paired with back squats depreciated 2.0 cm (main effect, p < 0.05). Conversely, CMJ paired with hang cleans depreciated 0.30 cm (interaction, p < 0.05). Thus, the best complex training scheme was achieved by pairing CMJs with hang cleans in comparison to back squats or CMJs in and of themselves. Future research on exercise modes of complex training that best help athletes preserve and train with the highest power possible, in a given training session, is warranted.

Air exchange rates and migration of VOCs in basements and residences

PubMed Central

Du, Liuliu; Batterman, Stuart; Godwin, Christopher; Rowe, Zachary; Chin, Jo-Yu

2015-01-01

Basements can influence indoor air quality by affecting air exchange rates (AERs) and by the presence of emission sources of volatile organic compounds (VOCs) and other pollutants. We characterized VOC levels, AERs and interzonal flows between basements and occupied spaces in 74 residences in Detroit, Michigan. Flows were measured using a steady-state multi-tracer system, and 7-day VOC measurements were collected using passive samplers in both living areas and basements. A walkthrough survey/inspection was conducted in each residence. AERs in residences and basements averaged 0.51 and 1.52 h−1, respectively, and had strong and opposite seasonal trends, e.g., AERs were highest in residences during the summer, and highest in basements during the winter. Air flows from basements to occupied spaces also varied seasonally. VOC concentration distributions were right-skewed, e.g., 90th percentile benzene, toluene, naphthalene and limonene concentrations were 4.0, 19.1, 20.3 and 51.0 μg m−3, respectively; maximum concentrations were 54, 888, 1117 and 134 μg m−3. Identified VOC sources in basements included solvents, household cleaners, air fresheners, smoking, and gasoline-powered equipment. The number and type of potential VOC sources found in basements are significant and problematic, and may warrant advisories regarding the storage and use of potentially strong VOCs sources in basements. PMID:25601281

Citrate- and Succinate-Modified Carbonate Apatite Nanoparticles with Loaded Doxorubicin Exhibit Potent Anticancer Activity against Breast Cancer Cells

PubMed Central

Mehbuba Hossain, Sultana; Chowdhury, Ezharul Hoque

2018-01-01

Biodegradable inorganic apatite-based particle complex is popular for its pH-sensitivity at the endosomal acidic environment to facilitate drug release following cellular uptake. Despite being a powerful anticancer drug, doxorubicin shows severe off-target effects and therefore would need a carrier for the highest effectiveness. We aimed to chemically modify carbonate apatite (CA) with Krebs cycle intermediates, such as citrate and succinate in order to control the growth of the resultant particles to more efficiently carry and transport the anticancer drug into the cancer cells. Citrate- or succinate-modified CA particles were synthesized with different concentrations of sodium citrate or sodium succinate, respectively, in the absence or presence of doxorubicin. The drug loading efficiency of the particles and their cellular uptake were observed by quantifying fluorescence intensity. The average diameter and surface charge of the particles were determined using Zetasizer. Cell viability was assessed by MTT assay. Citrate-modified carbonate apatite (CMCA) exhibited the highest (31.38%) binding affinity for doxorubicin and promoted rapid cellular uptake of the drug, leading to the half-maximal inhibitory concentration 1000 times less than that of the free drug in MCF-7 cells. Hence, CMCA nanoparticles with greater surface area enhance cytotoxicity in different breast cancer cells by enabling higher loading and more efficient cellular uptake of the drug. PMID:29534497

Large-scale synthesis of lead telluride (PbTe) nanotube-based nanocomposites with tunable morphology, crystallinity and thermoelectric properties

NASA Astrophysics Data System (ADS)

Park, Kee-Ryung; Cho, Hong-Baek; Song, Yoseb; Kim, Seil; Kwon, Young-Tae; Ryu, Seung Han; Lim, Jae-Hong; Lee, Woo-Jin; Choa, Yong-Ho

2018-04-01

A few millimeter-long lead telluride (PbTe) hollow nanofibers with thermoelectric properties was synthesized for the first time with high through manner via three-step sequential process of electrospinning, electrodeposition and cationic exchange reaction. As-synthesized electrospun Ag nanofibers with ultra-long aspect ratio of 10,000 were Te electrodeposited to obtain silver telluride nanotubes and underwent cationic exchange reaction in Pb(NO3)2 solution to obtain polycrystalline PbTe nanotubes with average diameter of 100 nm with 20 nm of wall thickness. Variation of the Ag-to-Pb ratio in the AgxTey-PbTe nanocomposites during the cationic exchange reaction enabled to control the thermoelectric properties of resulting 1D hollow nanofibers. The diameter of Ag nanofiber is the key factor to determine the final dimension of the PbTe nanotubes in the topotactic transformation and the content of Ag ion leads to the enhancement of thermoelectric properties in the AgxTey-PbTe nanocomposites. The synthesized 1D nanocomposite mats showed the highest value of Seebeck coefficient of 433 μV/K (at 300 K) when the remained Ag content was 30%, while the power factor reached highest to 0.567 μW/mK2 for the pure PbTe nanotubes. The enhancement of thermoelectric properties and the composite crystallinity are elucidated with relation to Ag contents in the resulting 1D nanocomposites.

Detection of bronchial breathing caused by pneumonia.

PubMed

Gross, V; Fachinger, P; Penzel, Th; Koehler, U; von Wichert, P; Vogelmeier, C

2002-06-01

The classic auscultation with stethoscope is the established clinical method for the detection of lung diseases. The interpretation of the sounds depends on the experience of the investigating physician. Therefore, a new computer-based method has been developed to classify breath sounds from digital lung sound recordings. Lung sounds of 11 patients with one-sided pneumonia and bronchial breathing were recorded on both the pneumonia side and on contralateral healthy side simultaneously using two microphones. The spectral power for the 300-600 Hz frequency band was computed for four respiratory cycles and normalized. For each breath, the ratio R between the time-segments (duration = 0.1 s) with the highest inspiratory and highest expiratory flow was calculated and averaged. We found significant differences in R between the pneumonia side (R = 1.4 +/- 1.3) and the healthy side (R = 0.5 +/- 0.5; p = 0.003 Wilcoxon-test) of lung. In 218 healthy volunteers we found R = 0.3 +/- 0.2 as a reference-value. The differences of ratio R (delta R) between the pneumonia side and the healthy side (delta R = 1.0 +/- 0.9) were significantly higher compared to follow-up studies after recovery (delta R = 0.0 +/- 0.1, p = 0.005 Wilcoxon-test). The computer based detection of bronchial breathing can be considered useful as part of a quantitative monitoring of patients at risk to develop pneumonia.

Influence of carbon electrode material on energy recovery from winery wastewater using a dual-chamber microbial fuel cell.

PubMed

Penteado, Eduardo D; Fernandez-Marchante, Carmen M; Zaiat, Marcelo; Gonzalez, Ernesto R; Rodrigo, Manuel A

2017-06-01

The aim of this work was to evaluate three carbon materials as anodes in microbial fuel cells (MFCs), clarifying their influence on the generation of electricity and on the treatability of winery wastewater, a highly organic-loaded waste. The electrode materials tested were carbon felt, carbon cloth and carbon paper and they were used at the same time as anode and cathode in the tests. The MFC equipped with carbon felt reached the highest voltage and power (72 mV and 420 mW m -2 , respectively), while the lowest values were observed when carbon paper was used as electrode (0.2 mV and 8.37·10 -6  mW m -2 , respectively). Chemical oxygen demand (COD) removal from the wastewater was observed to depend on the electrode material, as well. When carbon felt was used, the MFC showed the highest average organic matter consumption rate (650 mg COD L -1  d -1 ), whereas by using carbon paper the rate decreased to 270 mg COD L -1  d -1 . Therefore, both electricity generation and organic matter removal are strongly related not to the chemical composition of the electrode (which was graphite carbon in the three electrodes), but to its surface features and, consequently, to the amount of biomass adhered to the electrode surface.

High-power picosecond pulse delivery through hollow core photonic band gap fibers

NASA Astrophysics Data System (ADS)

Michieletto, Mattia; Johansen, Mette M.; Lyngsø, Jens K.; Lægsgaard, Jesper; Bang, Ole; Alkeskjold, Thomas T.

2016-03-01

We demonstrated robust and bend insensitive fiber delivery of high power laser with diffraction limited beam quality for two different kinds of hollow core band gap fibers. The light source for this experiment consists of ytterbium-doped double clad fiber aeroGAIN-ROD-PM85 in a high power amplifier setup. It provided 22ps pulses with a maximum average power of 95W, 40MHz repetition rate at 1032nm (~2.4μJ pulse energy), with M2 <1.3. We determined the facet damage threshold for a 7-cells hollow core photonic bandgap fiber and showed up to 59W average power output for a 5 meters fiber. The damage threshold for a 19-cell hollow core photonic bandgap fiber exceeded the maximum power provided by the light source and up to 76W average output power was demonstrated for a 1m fiber. In both cases, no special attention was needed to mitigate bend sensitivity. The fibers were coiled on 8 centimeters radius spools and even lower bending radii were present. In addition, stimulated rotational Raman scattering arising from nitrogen molecules was measured through a 42m long 19 cell hollow core fiber.

Environmentally Powered Yarn Arrays that Sense, Actuate, Harvest, and Store Energy (NBIT III)

DTIC Science & Technology

2016-11-15

than the gravimetric power generation capability of a cars combustion engine and (2) functioned as a torsional artificial muscle to rotate a heavy...rotor to over 90,000 rpm. By driving this torsional actuation using 19.6C fluctuations in air temperature, we obtained an average output electrical ...rpm. By driving this torsional actuation using 19.6°C fluctuations in air temperature, we obtained an average output electrical power of 124 W per

Wind Power Potential at Abandoned Mines in Korea

NASA Astrophysics Data System (ADS)

jang, M.; Choi, Y.; Park, H.; Go, W.

2013-12-01

This study performed an assessment of wind power potential at abandoned mines in the Kangwon province by analyzing gross energy production, greenhouse gas emission reduction and economic effects estimated from a 600 kW wind turbine. Wind resources maps collected from the renewable energy data center in Korea Institute of Energy Research(KIER) were used to determine the average wind speed, temperature and atmospheric pressure at hub height(50 m) for each abandoned mine. RETScreen software developed by Natural Resources Canada(NRC) was utilized for the energy, emission and financial analyses of wind power systems. Based on the results from 5 representative mining sites, we could know that the average wind speed at hub height is the most critical factor for assessing the wind power potential. Finally, 47 abandoned mines that have the average wind speed faster than 6.5 m/s were analyzed, and top 10 mines were suggested as relatively favorable sites with high wind power potential in the Kangwon province.

76 FR 65616 - Energy Conservation Program for Consumer Products: Test Procedures for Residential Central Air...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-24

... measure the energy efficiency, energy use or estimated annual operating cost of a covered product over an... the June 2010 NOPR would be used to determine the average power consumption of a residential central... residential central air conditioners, the unit's average power consumption during the heating season...

Power Management for Space Advanced Life Support

NASA Technical Reports Server (NTRS)

Jones, Harry

2001-01-01

Space power systems include the power source, storage, and management subsystems. In current crewed spacecraft, solar cells are the power source, batteries provide storage, and the crew performs any required load scheduling. For future crewed planetary surface systems using Advanced Life Support, we assume that plants will be grown to produce much of the crew's food and that nuclear power will be employed. Battery storage is much more costly than nuclear power capacity and so is not likely to be used. We investigate the scheduling of power demands by the crew or automatic control, to reduce the peak power load and the required generating capacity. The peak to average power ratio is a good measure of power use efficiency. We can easily schedule power demands to reduce the peak power from its maximum, but simple scheduling approaches may not find the lowest possible peak to average power ratio. An initial power scheduling example was simple enough for a human to solve, but a more complex example with many intermittent load demands required automatic scheduling. Excess power is a free resource and can be used even for minor benefits.

Design and fabrication of vibration based energy harvester using microelectromechanical system piezoelectric cantilever for low power applications.

PubMed

Kim, Moonkeun; Lee, Sang-Kyun; Yang, Yil Suk; Jeong, Jaehwa; Min, Nam Ki; Kwon, Kwang-Ho

2013-12-01

We fabricated dual-beam cantilevers on the microelectromechanical system (MEMS) scale with an integrated Si proof mass. A Pb(Zr,Ti)O3 (PZT) cantilever was designed as a mechanical vibration energy-harvesting system for low power applications. The resonant frequency of the multilayer composition cantilevers were simulated using the finite element method (FEM) with parametric analysis carried out in the design process. According to simulations, the resonant frequency, voltage, and average power of a dual-beam cantilever was 69.1 Hz, 113.9 mV, and 0.303 microW, respectively, at optimal resistance and 0.5 g (gravitational acceleration, m/s2). Based on these data, we subsequently fabricated cantilever devices using dual-beam cantilevers. The harvested power density of the dual-beam cantilever compared favorably with the simulation. Experiments revealed the resonant frequency, voltage, and average power density to be 78.7 Hz, 118.5 mV, and 0.34 microW, respectively. The error between the measured and simulated results was about 10%. The maximum average power and power density of the fabricated dual-beam cantilever at 1 g were 0.803 microW and 1322.80 microW cm(-3), respectively. Furthermore, the possibility of a MEMS-scale power source for energy conversion experiments was also tested.

Cadmium recovery by coupling double microbial fuel cells.

PubMed

Choi, Chansoo; Hu, Naixu; Lim, Bongsu

2014-10-01

Cr(VI)-MFC of the double microbial fuel cell (d-MFC) arrangement could successfully complement the insufficient voltage and power needed to recover cadmium metal from Cd(II)-MFC, which operated as a redox-flow battery. It was also possible to drain electrical energy from the d-MFC by an additional passage. The highest maximum utilization power density (22.5Wm(-2)) of Cr(VI)-MFC, with the cathode optimized with sulfate buffer, was 11.3times higher than the highest power density directly supplied to Cd(II)-MFC (2.0Wm(-2)). Cr(VI)-MFC could generate 3times higher power with the additional passage than without it; and the current density for the former was 4.2times higher than the latter at the same maximum power point (38.0Am(-2) vs. 9.0Am(-2)). This boosting phenomenon could be explained by the Le Chatelier's principle, which addresses the rate of electron-hole pair formation that can be accelerated by quickly removing electrons generated by microorganisms. Copyright © 2014 Elsevier Ltd. All rights reserved.

Medium power amplifiers covering 90 - 130 GHz for telescope local oscillators

NASA Technical Reports Server (NTRS)

Samoska, Lorene A.; Bryerton, Eric; Pukala, David; Peralta, Alejandro; Hu, Ming; Schmitz, Adele

2005-01-01

This paper describes a set of power amplifier (PA) modules containing InP High Electron Mobility Transistor (HEMT) Monolithic Millimeter-wave Integrated Circuit (MMIC) chips. The chips were designed and optimized for local oscillator sources in the 90-130 GHz band for the Atacama Large Millimeter Array telescope. The modules feature 20-45 mW of output power, to date the highest power from solid state HEMT MMIC modules above 110 GHz.

Power conditioning system modelling for nuclear electric propulsion

NASA Astrophysics Data System (ADS)

Metcalf, Kenneth J.

1993-11-01

NASA LeRC is currently developing a Fortran based model of a complete nuclear electric propulsion (NEP) vehicle that would be used for piloted and cargo missions to the Moon or Mars. The proposed vehicle design will use either a Brayton or K-Rankine power conversion cycle to drive a turbine coupled with a rotary alternator. Two thruster types are also being studied, ion and magnetoplasmadynamic (MPD). In support of this NEP model, Rocketdyne developed a power management and distribution (PMAD) subroutine that provides parametric outputs for selected alternator operating voltages and frequencies, thruster types, system power levels, and electronics coldplate temperatures. The end-to-end PMAD model described is based on the direct use of the alternator voltage and frequency for transmitting power to either ion or MPD thrusters. This low frequency transmission approach was compared with dc and high frequency ac designs, and determined to have the lowest mass, highest efficiency, highest reliability and lowest development costs. While its power quality is not as good as that provided by a high frequency system, it was considered adequate for both ion and MPD engine applications. The low frequency architecture will be used as the reference in future NEP PMAD studies.

Power Conditioning System Modelling for Nuclear Electric Propulsion

NASA Technical Reports Server (NTRS)

Metcalf, Kenneth J.

1993-01-01

NASA LeRC is currently developing a Fortran based model of a complete nuclear electric propulsion (NEP) vehicle that would be used for piloted and cargo missions to the Moon or Mars. The proposed vehicle design will use either a Brayton or K-Rankine power conversion cycle to drive a turbine coupled with a rotary alternator. Two thruster types are also being studied, ion and magnetoplasmadynamic (MPD). In support of this NEP model, Rocketdyne developed a power management and distribution (PMAD) subroutine that provides parametric outputs for selected alternator operating voltages and frequencies, thruster types, system power levels, and electronics coldplate temperatures. The end-to-end PMAD model described is based on the direct use of the alternator voltage and frequency for transmitting power to either ion or MPD thrusters. This low frequency transmission approach was compared with dc and high frequency ac designs, and determined to have the lowest mass, highest efficiency, highest reliability and lowest development costs. While its power quality is not as good as that provided by a high frequency system, it was considered adequate for both ion and MPD engine applications. The low frequency architecture will be used as the reference in future NEP PMAD studies.

PM2.5 and gaseous pollutants in New York State during 2005-2016: Spatial variability, temporal trends, and economic influences

NASA Astrophysics Data System (ADS)

Squizzato, Stefania; Masiol, Mauro; Rich, David Q.; Hopke, Philip K.

2018-06-01

Over the past decades, mitigation strategies have been adopted both by federal and state agencies in the United States (US) to improve air quality. Between 2007 and 2009, the US faced a financial/economic crisis that lowered activity and reduced emissions. At the same time, changes in the prices of coal and natural gas drove a shift in fuels used for electricity generation. Seasonal patterns, diel cycles, spatial gradients, and trends in PM2.5 and gaseous pollutants concentrations (NOx, SO2, CO and O3) monitored in New York State (NYS) from 2005 to 2016 were examined. Relationships between ambient concentrations, changes in NYS emissions retrieved from the US EPA trends inventory, and economic indicators were studied. PM2.5 and primary gaseous pollutants concentrations decreased across NYS. By 2016, PM2.5 and SO2 attained relatively homogeneous concentrations across the state. PM2.5 concentrations decreased significantly at all sites. Similarly, SO2 concentrations declined at all sites within this period, with the highest slopes observed at the urban sites. Reductions in NOx emissions likely contributed to summertime average ozone reductions. NOx and VOCs controls reduced O3 peak concentrations as seen in significant relationships between the annual O3 4th-highest daily maximum 8-h concentrations and estimated NOx emissions at rural and suburban sites (r2 ∼ 0.7). Spring maxima were not reduced with most sites showing insignificant slopes or significant positive slopes (e.g., +2.6% y-1 and +2% y-1, at CCNY and PFI, respectively). Increases in autumn and winter ozone concentrations were found (e,g., 6.6 ± 0.4% y-1 on average in New York City). Significant relationships were observed between PM2.5, primary pollutants, and economic indicators. Overall, a decrease in electricity generation with coal, and the simultaneous increase in natural gas consumption for power generation, led to a decrease in PM2.5 and gaseous pollutants concentrations.

Thermal effects in high average power optical parametric amplifiers.

PubMed

Rothhardt, Jan; Demmler, Stefan; Hädrich, Steffen; Peschel, Thomas; Limpert, Jens; Tünnermann, Andreas

2013-03-01

Optical parametric amplifiers (OPAs) have the reputation of being average power scalable due to the instantaneous nature of the parametric process (zero quantum defect). This Letter reveals serious challenges originating from thermal load in the nonlinear crystal caused by absorption. We investigate these thermal effects in high average power OPAs based on beta barium borate. Absorption of both pump and idler waves is identified to contribute significantly to heating of the nonlinear crystal. A temperature increase of up to 148 K with respect to the environment is observed and mechanical tensile stress up to 40 MPa is found, indicating a high risk of crystal fracture under such conditions. By restricting the idler to a wavelength range far from absorption bands and removing the crystal coating we reduce the peak temperature and the resulting temperature gradient significantly. Guidelines for further power scaling of OPAs and other nonlinear devices are given.

Test techniques for model development of repetitive service energy storage capacitors

NASA Astrophysics Data System (ADS)

Thompson, M. C.; Mauldin, G. H.

1984-03-01

The performance of the Sandia perfluorocarbon family of energy storage capacitors was evaluated. The capacitors have a much lower charge noise signature creating new instrumentation performance goals. Thermal response to power loading and the importance of average and spot heating in the bulk regions require technical advancements in real time temperature measurements. Reduction and interpretation of thermal data are crucial to the accurate development of an intelligent thermal transport model. The thermal model is of prime interest in the high repetition rate, high average power applications of power conditioning capacitors. The accurate identification of device parasitic parameters has ramifications in both the average power loss mechanisms and peak current delivery. Methods to determine the parasitic characteristics and their nonlinearities and terminal effects are considered. Meaningful interpretations for model development, performance history, facility development, instrumentation, plans for the future, and present data are discussed.

Capacity of MIMO free space optical communications using multiple partially coherent beams propagation through non-Kolmogorov strong turbulence.

PubMed

Deng, Peng; Kavehrad, Mohsen; Liu, Zhiwen; Zhou, Zhou; Yuan, Xiuhua

2013-07-01

We study the average capacity performance for multiple-input multiple-output (MIMO) free-space optical (FSO) communication systems using multiple partially coherent beams propagating through non-Kolmogorov strong turbulence, assuming equal gain combining diversity configuration and the sum of multiple gamma-gamma random variables for multiple independent partially coherent beams. The closed-form expressions of scintillation and average capacity are derived and then used to analyze the dependence on the number of independent diversity branches, power law α, refractive-index structure parameter, propagation distance and spatial coherence length of source beams. Obtained results show that, the average capacity increases more significantly with the increase in the rank of MIMO channel matrix compared with the diversity order. The effect of the diversity order on the average capacity is independent of the power law, turbulence strength parameter and spatial coherence length, whereas these effects on average capacity are gradually mitigated as the diversity order increases. The average capacity increases and saturates with the decreasing spatial coherence length, at rates depending on the diversity order, power law and turbulence strength. There exist optimal values of the spatial coherence length and diversity configuration for maximizing the average capacity of MIMO FSO links over a variety of atmospheric turbulence conditions.

Environmental effects of interstate power trading on electricity consumption mixes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joe Marriott; H. Scott Matthews

2005-11-15

Although many studies of electricity generation use national or state average generation mix assumptions, in reality a great deal of electricity is transferred between states with very different mixes of fossil and renewable fuels, and using the average numbers could result in incorrect conclusions in these studies. The authors create electricity consumption profiles for each state and for key industry sectors in the U.S. based on existing state generation profiles, net state power imports, industry presence by state, and an optimization model to estimate interstate electricity trading. Using these 'consumption mixes' can provide a more accurate assessment of electricity usemore » in life-cycle analyses. It is concluded that the published generation mixes for states that import power are misleading, since the power consumed in-state has a different makeup than the power that was generated. And, while most industry sectors have consumption mixes similar to the U.S. average, some of the most critical sectors of the economy - such as resource extraction and material processing sectors - are very different. This result does validate the average mix assumption made in many environmental assessments, but it is important to accurately quantify the generation methods for electricity used when doing life-cycle analyses. 16 refs., 7 figs., 2 tabs.« less

General Cognitive Ability Predicts Job Performance

DTIC Science & Technology

1992-01-01

of criteria has been and remains the center of controversy. Early intelligence test developers such as Binet and Simon were proponents of g but...Vocational Behavior ( Gottfredson , 1986) documen --,d the renewed interest as did the evidence emerging from validity generalization studies (Hunter, 1983...Among the jobs with highest average estimated intelligence were accounting, engineering, and medicine. Jobs with middling average estimated intelligence

Interpreting seasonal changes of low-tropospheric CO2 over China based on SCIAMACHY observations during 2003-2011

NASA Astrophysics Data System (ADS)

Xi, Wang; Xingying, Zhang; Liyang, Zhang; Ling, Gao; Lin, Tian

2015-02-01

The atmospheric carbon dioxide (CO2) concentration exhibits a strong seasonal variation. Analyzing the regional seasonal cycle could help to improve the interpretation of the sources and sinks of CO2 over certain areas. Based on a long-term (2003-2011) retrieved dataset from the SCanning Imaging Absorption spectroMeter for Atmospheric CHartographY (SCIAMACHY), the seasonal cycle and inter-annual variations of column-averaged dry air mole fraction of atmospheric carbon dioxide (XCO2) over China have been analyzed. The result shows that XCO2 over China increases by about 4.2% from 2003 to 2011, but the seasonal fluctuation keeps the similar pattern with the average peak-to-peak amplitude of 9.35 ppm. The highest concentration appears in spring, and the lowest value always occurs in summer. Based on the multi-year averages, it can be discerned that the seasonal signal of XCO2 increases during colder seasons with a drop during the period from December to February of the following year. The potential affecting factors are also discussed in this manuscript, including Normalized Difference Vegetation Index (NDVI), air temperature, and industrial productions in Thermal Power Generation (TPG) and cement that are relative main contributors for the anthropogenic CO2 of China. The seasonal variations of CO2 are highly connected with the changes of NDVI and air temperature. While the increase of the anthropogenic CO2 emission over China since 2003 is probably caused by the rapid growth of coal combustion and cement manufacture.

5-year analysis of background surface ozone and carbon dioxide variations during summer seasons at Terra Nova Bay (Antarctica)

NASA Astrophysics Data System (ADS)

Cristofanelli, Paolo; Bonasoni, Paolo; Bonafe', Ubaldo; Calzolari, Frencescopiero; Duchi, Rocco; Lanconelli, Christian; Lupi, Angelo; Vitale, Vito; Colombo, Tiziano

2010-05-01

Carbon dioxide (CO2) and tropospheric ozone (O3) play important roles in determining the radiative budget of the atmosphere. While CO2 is considered the most important anthropogenic greenhouse gas, O3 is evaluated as the third most powerful greenhouse gas since pre-industrial ages and, by influencing the lifetime of others greenhouse gases, it provides also an indirect impact on climate. Within the framework of the Italian National Programme of Antarctic Researches (PNRA), continuous measurements of CO2, O3 as well as meteorological parameters have been conducted at the clean-air facility of Icaro Camp at the "Mario Zucchelli" Station (74.7 S, 164.1 E, 41 m a.s.l., hereinafter MZS-IC) during five experimental summer campaigns from November 2001 to February 2006. At MZS-IC, average O3 background concentrations ranged from 18.5 +/- 4.6 ppbv (summer 2005 - 2006) to 22.0 +/- 4.3 ppbv (summer 2003 - 2004). For CO2, in good agreement with the global trend observed for the period 2001-2006, background concentrations showed an average growth rate of 2.12 ppmv/year ranging from 369.28 +/- 0.18 ppmv during the summer 2001 - 2002 to 377.76 +/- 0.26 ppmv during the summer 2005 - 2006. On average, over the five summer campaigns, the O3 behaviour showed a decreasing trend with highest values in November and a minimum in January, while a broad December-January minimum characterised CO2, well tracing the typical O3 and CO2 high-latitude seasonal cycles in the Southern Hemisphere.

Evaluating the Feasibility of Five Candidate DNA Barcoding Loci for Philippine Lasianthus Jack (Lasiantheae: Rubiaceae).

PubMed

Arshed, Muhammad Jefte C; Valdez, Marcos B; Alejandro, Grecebio Jonathan D

2017-01-01

The pantropical genus Lasianthus Jack is identified for high phenotypic plasticity making traditional taxonomic identification difficult. Having some members with important medicinal properties, a precise complimentary identification through DNA barcoding is needed for species delineation. In this study, 12 samples representing six Philippine Lasianthus species were used to determine the most efficient barcoding loci among the cpDNA markers ( mat K, rbc L, rps 16, and trn T-F) and nrDNA (ITS) based on the criteria of universality, discriminatory power, and resolution of species. The results revealed that ITS has the recommended primer universality, greatest interspecific divergences, and average resolution of species. Among the cpDNA markers, mat K and rbc L are recommended but with minimal resolution of species. While trn T-F showed moderate interspecific variations and resolution of Lasianthus species, rps 16 has the lowest interspecific divergence and resolution of species. Consequently, ITS is the potential ideal DNA barcode for Lasianthus species. ITS, mat K, and rps 16 markers have the excellent amplification and sequence qualityITS marker has the highest interspecific divergence with the maximum values, followed by mat K, rbc L, trn T-F, and rps 16, respectivelyAll markers except rps 16 yielded average resolution to Lasianthus speciesITS marker is the most ideal locus in terms of excellent universality, high interspecific discriminatory ability, and average species resolution. Abbreviations used: ITS: Internal Transcribe Spacer, mat K: maturase K, rbc L: ribulose-1,5-biphospahte-carboxylase, rps 16: ribosomal protein 16 small subunit gene.

Geomagnetism during solar cycle 23: Characteristics

PubMed Central

Zerbo, Jean-Louis; Amory-Mazaudier, Christine; Ouattara, Frédéric

2012-01-01

On the basis of more than 48 years of morphological analysis of yearly and monthly values of the sunspot number, the aa index, the solar wind speed and interplanetary magnetic field, we point out the particularities of geomagnetic activity during the period 1996–2009. We especially investigate the last cycle 23 and the long minimum which followed it. During this period, the lowest values of the yearly averaged IMF (3 nT) and yearly averaged solar wind speed (364 km/s) are recorded in 1996, and 2009 respectively. The year 2003 shows itself particular by recording the highest value of the averaged solar wind (568 km/s), associated to the highest value of the yearly averaged aa index (37 nT). We also find that observations during the year 2003 seem to be related to several coronal holes which are known to generate high-speed wind stream. From the long time (more than one century) study of solar variability, the present period is similar to the beginning of twentieth century. We especially present the morphological features of solar cycle 23 which is followed by a deep solar minimum. PMID:25685427

Indonesia sea surface temperature from TRMM Microwave Imaging (TMI) sensor

NASA Astrophysics Data System (ADS)

Marini, Y.; Setiawan, K. T.

2018-05-01

We analysis the Tropical Rainfall Measuring Mission's (TRMM) Microwave Imager (TMI) data to monitor the sea surface temperature (SST) of Indonesia waters for a decade of 2005-2014. The TMI SST data shows the seasonal and interannual SST in Indonesian waters. In general, the SST average was highest in March-May period with SST average was 29.4°C, and the lowest was in June – August period with the SST average was 28.5°C. The monthly SST average fluctuation of Indonesian waters for 10 years tends to increase. The lowest SST average of Indonesia occurred in August 2006 with the SST average was 27.6° C, while the maximum occurred in May 2014 with the monthly SST average temperature was 29.9 ° C.