Optimization of the Microwave-Assisted Ethanosolv Extraction of Lignocellulosic Compounds from the Bagasse of Agave angustifolia Haw Using the Response Methodology.

PubMed

Hernández, Yuliana Rosas; García Serrano, Luz Arcelia; Maruri, Daniel Tapia; Jiménez Aparicio, Antonio Ruperto; Camacho Díaz, Brenda Hildeliza; Arenas Ocampo, Martha Lucía

2018-04-04

The main objective of this work was to optimize the process of fractionation of the bagasse of Agave angustifolia Haw, applying organosolv assisted with microwaves. The DCC was used to evaluate the effect of independent variables such as ethanol concentration (40, 50, and 60%) and reaction time (1, 1.5, and 2 h) on yield, cellulose and lignin percentages. Lignocellulosic fractions (F1 and F2) were obtained by means of organosolv assisted with microwave in an open system (atmospheric pressure) and a closed system (controlled pressure). The lignocellulosic fractions were microstructurally characterized. The highest extraction yields (70.39%) were reached in the open system at 50% ethanol for 1.5 h. The highest percentages of LK (5.05%) were obtained in the closed system at 60% ethanol for 2 h. The SEM photomicrograph showed that the microstructure of F1 was retained even after treatment with 60% ethanol for 2 h, and the exposure of the fibrillar part was observed obtaining the disposition of pectin.

Simultaneous Hydrogen and Methane Production Through Multi-Phase Anaerobic Digestion of Paperboard Mill Wastewater Under Different Operating Conditions.

PubMed

Farghaly, Ahmed; Tawfik, Ahmed

2017-01-01

Multi-phase anaerobic reactor for H 2 and CH 4 production from paperboard mill wastewater was studied. The reactor was operated at hydraulic retention times (HRTs) of 12, 18, 24, and 36 h, and organic loading rates (OLRs) of 2.2, 1.5, 1.1, and 0.75 kg chemical oxygen demand (COD)/m 3  day, respectively. HRT of 12 h and OLR of 2.2 kg COD/m 3  day provided maximum hydrogen yield of 42.76 ± 14.5 ml/g COD removed and volumetric substrate uptake rate (-rS) of 16.51 ± 4.43 mg COD/L h. This corresponded to the highest soluble COD/total COD (SCOD/TCOD) ratio of 56.25 ± 3.3 % and the maximum volatile fatty acid (VFA) yield (Y VFA ) of 0.21 ± 0.03 g VFA/g COD, confirming that H 2 was mainly produced through SCOD conversion. The highest methane yield (18.78 ± 3.8 ml/g COD removed ) and -rS of 21.74 ± 1.34 mgCOD/L h were achieved at an HRT of 36 h and OLR of 0.75 kg COD/m 3  day. The maximum hydrogen production rate (HPR) and methane production rate (MPR) were achieved at carbon to nitrogen (C/N) ratio of 47.9 and 14.3, respectively. This implies the important effect of C/N ratio on the distinction between the dominant microorganism bioactivities responsible for H 2 and CH 4 production.

Succinic Acid Production from Cheese Whey using Actinobacillus succinogenes 130 Z

NASA Astrophysics Data System (ADS)

Wan, Caixia; Li, Yebo; Shahbazi, Abolghasem; Xiu, Shuangning

Actinobacillus succinogenes 130 Z was used to produce succinic acid from cheese whey in this study. At the presence of external CO2 supply, the effects of initial cheese whey concentration, pH, and inoculum size on the succinic acid production were studied. The by-product formation during the fermentation process was also analyzed. The highest succinic acid yield of 0.57 was obtained at initial cheese whey concentration of 50 g/L, while the highest succinic acid productivity of 0.58 g h-1 L-1 was obtained at initial cheese whey concentration of 100 g/L. Increase in pH and inoculum size caused higher succinic acid yield and productivity. At the preferred fermentation condition of pH 6.8, inoculum size of 5% and initial cheese whey concentration of 50 g/L, succinic acid yield of 0.57, and productivity of 0.44 g h-1 L-1 were obtained. Acetic acid and formic acid were the main by-products throughout the fermentation run of 48 h. It is feasible to produce succinic acid using lactose from cheese whey as carbon resource by A. succinogenes 130 Z.

Effects of operational parameters on dark fermentative hydrogen production from biodegradable complex waste biomass.

PubMed

Ghimire, Anish; Sposito, Fabio; Frunzo, Luigi; Trably, Eric; Escudié, Renaud; Pirozzi, Francesco; Lens, Piet N L; Esposito, Giovanni

2016-04-01

This work aimed to investigate the effect of the initial pH, combination of food to microorganism ratio (F/M) and initial pH, substrate pre-treatment and different inoculum sources on the dark fermentative biohydrogen (H2) yields. Three model complex waste biomasses (food waste, olive mill wastewater (OMWW) and rice straw) were used to assess the effect of the aforementioned parameters. The effect of the initial pH between 4.5 and 7.0 was investigated in batch tests carried out with food waste. The highest H2 yields were shown at initial pH 4.5 (60.6 ± 9.0 mL H2/g VS) and pH 5.0 (50.7 ± 0.8 mL H2/g VS). Furthermore, tests carried out with F/M ratios of 0.5, 1.0 and 1.5 at initial pH 5.0 and 6.5 revealed that a lower F/M ratio (0.5 and 1.0) favored the H2 production at an initial pH 5.0 compared to pH 6.5. Alkaline pre-treatment of raw rice straw using 4% and 8% NaOH at 55°C for 24h, increased the H2 yield by 26 and 57-fold, respectively. In the dark fermentation of OMWW, the H2 yield was doubled when heat-shock pre-treated activated sludge was used as inoculum in comparison to anaerobic sludge. Overall, this study shows that the application of different operating parameters to maximize the H2 yields strongly depends on the biodegradability of the substrate. Copyright © 2016 Elsevier Ltd. All rights reserved.

Ammonia Formation by the Reduction of Nitrite/Nitrate by FeS: Ammonia Formation Under Acidic Conditions

NASA Technical Reports Server (NTRS)

Summers, David P.; DeVincenzi, Donald (Technical Monitor)

2000-01-01

FeS reduces nitrite to, ammonia at pHs lower than the corresponding reduction by aqueous Fe+2. The reduction follows a reasonable first order decay, in nitrite concentration, with a half life of about 150 min (room temperature, CO2, pH 6.25). The highest ammonia product yield measured was 53%. Under CO2, the product yield decreases from pH 5.0 to pH 6.9. The increasing concentration of bicarbonate at higher pH interferes with the reaction. Bicarbonate interference is shown by comparing runs under N2 and CO2. The reaction proceeds well in the presence of such species as chloride, sulfate, and phosphate though the yield drops significantly with phosphate. FeS also reduces nitrate and, unlike with Fe+2, the reduction shows more reproducibility. Again, the product yield decreases with increasing pH, from 7% at pH 4.7 to 0% at pH 6.9. It appears as if nitrate is much more sensitive to the presence of added species, perhaps not competing as well for binding sites on the FeS surface. This may be the cause of the lack of reproducibility of nitrate reduction by Fe+2 (which also can be sensitive to binding by certain species).

Acid extraction of molybdenum, nickel and cobalt from mineral sludge generated by rainfall water at a metal recycling plant.

PubMed

Vemic, M; Bordas, F; Guibaud, G; Comte, S; Joussein, E; Lens, P N L; Van Hullebusch, E D

2016-01-01

This study investigated the leaching yields of Mo, Ni and Co from a mineral sludge of a metal recycling plant generated by rainfalls. The investigated mineral sludge had a complex heterogeneous composition, consisting of particles of settled soil combined with metal-bearing particles (produced by catalysts, metallic oxides and battery recycling). The leaching potential of different leaching reagents (stand-alone strong acids (HNO3 (68%), H2SO4 (98%) and HCl (36%)) and acid mixtures (aqua regia (nitric + hydrochloric (1:3)), nitric + sulphuric (1:1) and nitric + sulphuric + hydrochloric (2:1:1)) was investigated at changing operational parameters (solid-liquid (S/L) ratio, leaching time and temperature), in order to select the leaching reagent which achieves the highest metal leaching yields. Sulphuric acid (98% H2SO4) was found to be the leachant with the highest metal leaching potential. The optimal leaching conditions were a three-stage successive leaching at 80 °C with a leaching time of 2 h and S/L ratio of 0.25 g L(-1). Under these conditions, the achieved mineral sludge sample leaching yields were 85.5%, 40.5% and 93.8% for Mo, Ni and Co, respectively. The higher metal leaching potential of H2SO4 in comparison with the other strong acids/acid mixtures is attributed to the fact that H2SO4 is a diacidic compound, thus it has more H(+) ions, resulting in its stronger oxidizing power and corrosiveness.

Syngas production by chemical-looping gasification of wheat straw with Fe-based oxygen carrier.

PubMed

Hu, Jianjun; Li, Chong; Guo, Qianhui; Dang, Jiatao; Zhang, Quanguo; Lee, Duu-Jong; Yang, Yunlong

2018-05-03

The iron-based oxygen carriers (OC's), Fe 2 O 3 /support (Al 2 O 3 , TiO 2 , SiO 2 and ZrO 2 ), for chemical looping gasification of wheat straw were prepared using impregnation method. The surface morphology, crystal structure, carbon deposition potential, lattice oxygen activity and selectivity of the yielded OCs were examined. The Fe 2 O 3 /Al 2 O 3 OCs at 60% loading has the highest H 2 yield, H 2 /CO ratio, gas yield, and carbon conversion amongst the tested OC's. Parametric studies revealed that an optimal loading Fe 2 O 3 of 60%, steam-to-biomass ratio of 0.8 and oxygen carrier-to-biomass ratio of 1.0 led to the maximum H 2 /CO ratio, gas yield, H 2  + CO ratio, and carbon conversion from the gasified wheat straw. High temperature, up to 950 °C, enhanced the gasification performance. A kinetic network interpreted the noted experimental results. The lattice oxygen provided by the prepared Fe 2 O 3 /Al 2 O 3 oxygen carriers promotes chemical looping gasification efficiencies from wheat straw. Copyright © 2018 Elsevier Ltd. All rights reserved.

Comparison of Seven Chemical Pretreatments of Corn Straw for Improving Methane Yield by Anaerobic Digestion

PubMed Central

Song, Zilin; GaiheYang; Liu, Xiaofeng; Yan, Zhiying; Yuan, Yuexiang; Liao, Yinzhang

2014-01-01

Agriculture straw is considered a renewable resource that has the potential to contribute greatly to bioenergy supplies. Chemical pretreatment prior to anaerobic digestion can increase the anaerobic digestibility of agriculture straw. The present study investigated the effects of seven chemical pretreatments on the composition and methane yield of corn straw to assess their effectiveness of digestibility. Four acid reagents (H2SO4, HCl, H2O2, and CH3COOH) at concentrations of 1%, 2%, 3%, and 4% (w/w) and three alkaline reagents (NaOH, Ca(OH)2, and NH3·H2O) at concentrations of 4%, 6%, 8%, and 10% (w/w) were used for the pretreatments. All pretreatments were effective in the biodegradation of the lignocellulosic straw structure. The straw, pretreated with 3% H2O2 and 8% Ca(OH)2, acquired the highest methane yield of 216.7 and 206.6 mL CH4 g VS −1 in the acid and alkaline pretreatments, which are 115.4% and 105.3% greater than the untreated straw. H2O2 and Ca(OH)2 can be considered as the most favorable pretreatment methods for improving the methane yield of straw because of their effectiveness and low cost. PMID:24695485

Comparison of seven chemical pretreatments of corn straw for improving methane yield by anaerobic digestion.

PubMed

Song, Zilin; GaiheYang; Liu, Xiaofeng; Yan, Zhiying; Yuan, Yuexiang; Liao, Yinzhang

2014-01-01

Agriculture straw is considered a renewable resource that has the potential to contribute greatly to bioenergy supplies. Chemical pretreatment prior to anaerobic digestion can increase the anaerobic digestibility of agriculture straw. The present study investigated the effects of seven chemical pretreatments on the composition and methane yield of corn straw to assess their effectiveness of digestibility. Four acid reagents (H2SO4, HCl, H2O2, and CH3COOH) at concentrations of 1%, 2%, 3%, and 4% (w/w) and three alkaline reagents (NaOH, Ca(OH)2, and NH3·H2O) at concentrations of 4%, 6%, 8%, and 10% (w/w) were used for the pretreatments. All pretreatments were effective in the biodegradation of the lignocellulosic straw structure. The straw, pretreated with 3% H2O2 and 8% Ca(OH)2, acquired the highest methane yield of 216.7 and 206.6 mL CH4 g VS(-1) in the acid and alkaline pretreatments, which are 115.4% and 105.3% greater than the untreated straw. H2O2 and Ca(OH)2 can be considered as the most favorable pretreatment methods for improving the methane yield of straw because of their effectiveness and low cost.

Ozone dose-response relationships for spring oilseed rape and broccoli

NASA Astrophysics Data System (ADS)

De Bock, Maarten; Op de Beeck, Maarten; De Temmerman, Ludwig; Guisez, Yves; Ceulemans, Reinhart; Vandermeiren, Karine

2011-03-01

Tropospheric ozone is an important air pollutant with known detrimental effects for several crops. Ozone effects on seed yield, oil percentage, oil yield and 1000 seed weight were examined for spring oilseed rape ( Brassica napus cv. Ability). For broccoli ( Brassica oleracea L. cv. Italica cv. Monaco) the effects on fresh marketable weight and total dry weight were studied. Current ozone levels were compared with an increase of 20 and 40 ppb during 8 h per day, over the entire growing season. Oilseed rape seed yield was negatively correlated with ozone dose indices calculated from emergence until harvest. This resulted in an R2 of 0.24 and 0.26 ( p < 0.001) for the accumulated hourly O 3 exposure over a threshold of 40 ppb (AOT40) and the phytotoxic ozone dose above a threshold of 6 nmol m -2 s -1 (POD 6) respectively. Estimated critical levels, above which 5% yield reduction is expected, were 3.7 ppm h and 4.4 mmol m -2 respectively. Our results also confirm that a threshold value of 6 nmol s -1 m -2 projected leaf area, as recommended for agricultural crops (UNECE, Mills, 2004), can indeed be applied for spring oilseed rape. The reduction of oilseed rape yield showed the highest correlation with the ozone uptake during the vegetative growth stage: when only the first 47 days after emergence were used to calculate POD 6, R2 values increased up to 0.476 or even 0.545 when the first 23 days were excluded. The highest ozone treatments, corresponding to the future ambient level by 2100 (IPCC, Meehl et al., 2007), led to a reduction of approximately 30% in oilseed rape seed yield in comparison to the current ozone concentrations. Oil percentage was also significantly reduced in response to ozone ( p < 0.001). As a consequence oil yield was even more severely affected by elevated ozone exposure compared to seed yield: critical levels for oil yield dropped to 3.2 ppm h and 3.9 mmol m -2. For broccoli the applied ozone doses had no effect on yield.

Effect of yeast extract addition to a mineral salts medium containing hydrolyzed plant xylan on fungal pullulan production.

PubMed

Kennedy Ii, Daniel E; West, Thomas P

2018-05-16

The ability of the fungus Aureobasidium pullulans ATCC 42023 to produce pullulan from yeast extract-supplemented xylan hydrolysates of the prairie grass prairie cordgrass was examined relative to polysaccharide and cell biomass production, yield, and pullulan content of the polysaccharide. A pullulan concentration of 11.2 g L-1 and yield of 0.79 g g-1 was produced by ATCC 42023 when grown for 168 h at 30°C on the phosphate-buffered hydrolysate supplemented with yeast extract. The highest biomass level being 8.8 g L-1 was produced by ATCC 42023 after 168 h on a yeast extract-supplemented, hydrolysate-containing complete medium lacking sodium chloride. The highest pullulan content of the polysaccharide produced by ATCC 42023 after 168 h on the hydrolysate medium supplemented with yeast extract and ammonium sulfate was 70%. The findings indicate that a polysaccharide with a high pullulan content can be produced at a relatively high yield by the fungus grown on a yeast extract-supplemented xylan hydrolysate, suggesting that pullulan could be produced using a biomass-based process.

γ-Dodecelactone production from safflower oil via 10-hydroxy-12(Z)-octadecenoic acid intermediate by whole cells of Candida boidinii and Stenotrophomonas nitritireducens.

PubMed

Jo, Ye-Seul; An, Jung-Ung; Oh, Deok-Kun

2014-07-16

Candida boidinii was selected as a γ-dodecelactone producer because of the highest production of γ-dodecelactone from 10-hydroxy-12(Z)-octadecenoic acid among the 11 yeast strains tested. Under the reaction conditions of pH 5.5 and 25 °C with 5 g/L 10-hydroxy-12(Z)-octadecenoic acid and 30 g/L cells, whole C. boidinii cells produced 2.1 g/L γ-dodecelactone from 5 g/L 10-hydroxy-12(Z)-octadecenoic acid after 6 h, with a conversion yield of 64% (mol/mol) and a volumetric productivity of 350 mg/L/h. The production of γ-dodecelactone from safflower oil was performed by lipase hydrolysis reaction and two-step whole-cell biotransformation using Stenotrophomonas nitritireducens and C. boidinii. γ-Dodecelactone at 1.88 g/L was produced from 7.5 g/L safflower oil via 5 g/L 10-hydroxy-12(Z)-octadecenoic acid intermediate by these reactions after 8 h of reaction time, with a volumetric productivity of 235 mg/L/h and a conversion yield of 25% (w/w). To the best of the authors' knowledge, this is the highest volumetric productivity and conversion yield reported to date for the production of γ-lactone from natural oils.

Electro-peroxone degradation of diethyl phthalate: Cathode selection, operational parameters, and degradation mechanisms.

PubMed

Hou, Meifang; Chu, Yaofei; Li, Xiang; Wang, Huijiao; Yao, Weikun; Yu, Gang; Murayama, Seiichi; Wang, Yujue

2016-12-05

This study compares the degradation of diethyl phthalate (DEP) by the electro-peroxone (E-peroxone) process with three different carbon-based cathodes, namely, carbon-polytetrafluorethylene (carbon-PTFE), carbon felt, and reticulated vitreous carbon (RVC). Results show that the three cathodes had different electrocatalytic activity for converting sparged O2 to H2O2, which increased in order of carbon felt, RVC, and carbon-PTFE. The in-situ generated H2O2 then reacts with sparged O3 to yield OH, which can in turn oxidize ozone-refractory DEP toward complete mineralization. In general, satisfactory total organic carbon removal yields (76.4-91.8%) could be obtained after 60min of the E-peroxone treatment with the three carbon-based cathodes, and the highest yield was obtained with the carbon-PTFE cathode due to its highest activity for H2O2 generation. In addition, the carbon-PTFE and carbon felt cathodes exhibited excellent stability over six cycles of the E-peroxone treatment of DEP solutions. Based on the intermediates (e.g., monoethyl phthalate, phthalic acid, phenolics, and carboxylic acids) identified by HPLC-UV, plausible reaction pathways were proposed for DEP mineralization by the E-peroxone process. The results of this study indicate that carbon-based cathodes generally have good electrocatalytic activity and stability for application in extended E-peroxone operations to effectively remove phthalates from water. Copyright © 2015 Elsevier B.V. All rights reserved.

Automobile shredded residue valorisation by hydrometallurgical metal recovery.

PubMed

Granata, Giuseppe; Moscardini, Emanuela; Furlani, Giuliana; Pagnanelli, Francesca; Toro, Luigi

2011-01-15

The aim of this work was developing a hydrometallurgical process to recover metals from automobile shredded residue (or car fluff). Automobile shredded residue (ASR) was characterised by particle size distribution, total metal content and metal speciation in order to guide the choice of target metals and the operating conditions of leaching. Characterisation results showed that Fe is the most abundant metal in the waste, while Zn was the second abundant metal in the fraction with diameter lower than 500 μm. Sequential extractions denoted that Zn was easily extractable by weak acid attack, while Fe and Al required a strong acid attack to be removed. In order to recover zinc from <500 μm fraction leaching tests were operated using acetic acid, sulphuric acid and sodium hydroxide at different concentrations. Sulphuric acid determined the highest zinc extraction yield, while acetic acid determined the highest zinc extractive selectivity. Sodium hydroxide promoted an intermediate situation between sulphuric and acetic acid. Zn recovery by electro winning using acetic leach liquor determined 95% of Zn electro deposition yield in 1h, while using sulphuric leach liquor 40% yield in 1h and 50% yield in 2h were obtained. Simulation results showed that the sulphuric leaching process was more attractive than acetic leaching process. Copyright © 2010 Elsevier B.V. All rights reserved.

Analysis of microbial community adaptation in mesophilic hydrogen fermentation from food waste by tagged 16S rRNA gene pyrosequencing.

PubMed

Laothanachareon, Thanaporn; Kanchanasuta, Suwimon; Mhuanthong, Wuttichai; Phalakornkule, Chantaraporn; Pisutpaisal, Nipon; Champreda, Verawat

2014-11-01

Dark fermentation is an attractive process for generation of biohydrogen, which involves complex microbial processes on decomposition of organic wastes and subsequent conversion of metabolic intermediates to hydrogen. The microbes present in an upflow anaerobic sludge blanket (UASB) reactor for waste water treatment were tested for application in batch dark fermentation of food waste at varying ratios of feedstock to heat-treated microbial inoculum (F/M) of 1-8 (g TVS/g TVS). Biohydrogen yields between 0.39 and 2.68 mol H2/mol hexose were obtained, indicating that the yields were highly dependent on the starting F/M ratio. The highest H2 purity of 66% was obtained from the first 8 h of fermentation at the F/M ratio of 2, whereas the highest H2 production was obtained after 35 h of fermentation at the F/M ratio of 5. Tagged 16S rRNA gene pyrosequencing showed that the seed culture comprised largely of uncultured bacteria with various Proteobacteria, Bacteroidetes, and Firmicutes, while the starting food waste contained mainly lactic acid bacteria. Enrichment of Firmicutes, particularly Clostridia and lactic acid bacteria occurred within 8 h of the dark fermentation and the H2 producing microcosm at 35 h was dominated >80% by Clostridium spp. The major H2 producer was identified as a Clostridial strain related to Clostridium frigidicarnis. This work demonstrated the adaption of the microbial community during the dark fermentation of complex food waste and revealed the major roles of Clostridia in both substrate degradation and biohydrogen production. Copyright © 2014 Elsevier Ltd. All rights reserved.

Characterization of Hanwoo Bovine By-products by Means of Yield, Physicochemical and Nutritional Compositions

PubMed Central

Moon, Sung Sil

2014-01-01

Though the edible bovine by-products are widely used for human consumption in most countries worldwide but the scientific information regarding the nutritional quality of these by-products is scarce. In the present study, the basic information regarding the yields, physicochemical and nutritional compositions of edible Hanwoo bovine by-products was studied. Our results showed that the yields, physicochemical and nutritional composition widely varied between the by-products examined. The highest pH values were found in rumen, reticulum, omasum and reproductive organ. Heart, liver, kidney and spleen had the lowest CIE L* values and highest CIE a* values. Liver had the highest vitamin A, B2 and niacin contents whereas the highest B1 and B5 contents were found in kidney. The highest Ca content was found in rumen, reticulum, omasum, head and leg while the highest Mn and Fe contents were found in rumen, omasum and spleen, respectively. Liver had the highest Cu content. Total essential amino acids (EAA)/amino acids (AA) ratios ranged between the by-products from 38.37% to 47.41%. Total polyunsaturated fatty acids (PUFA) levels ranged between the by-products from 2.26% to 26.47%, and most by-products showed favorable PUFA/SFA ratios. It is concluded that most of by-products examined are good sources of essential nutrients and these data will be of great importance for promotion of consumption and utilization of beef by-products in future. PMID:26761281

Organic loading rate impact on biohydrogen production and microbial communities at anaerobic fluidized thermophilic bed reactors treating sugarcane stillage.

PubMed

Santos, Samantha Christine; Rosa, Paula Rúbia Ferreira; Sakamoto, Isabel Kimiko; Varesche, Maria Bernadete Amâncio; Silva, Edson Luiz

2014-05-01

This study aimed to evaluate the effect of high organic loading rates (OLR) (60.0-480.00 kg COD m(-3)d(-1)) on biohydrogen production at 55°C, from sugarcane stillage for 15,000 and 20,000 mg CODL(-1), in two anaerobic fluidized bed reactors (AFBR1 and AFBR2). It was obtained, for H2 yield and content, a decreasing trend by increasing the OLR. The maximum H2 yield was observed in AFBR1 (2.23 mmol g COD added(-1)). The volumetric H2 production was proportionally related to the applied hydraulic retention time (HRT) of 6, 4, 2 and 1h and verified in AFBR1 the highest value (1.49 L H2 h(-1)L(-1)). Among the organic acids obtained, there was a predominance of lactic acid (7.5-22.5%) and butyric acid (9.4-23.8%). The microbial population was set with hydrogen-producing fermenters (Megasphaera sp.) and other organisms (Lactobacillus sp.). Copyright © 2014 Elsevier Ltd. All rights reserved.

Light response of sunflower and canola as affected by plant density, plant genotype and N fertilization.

PubMed

Soleymani, A

2017-08-01

Crop response to light is an important parameter determining crop growth. Three field (split plots) experiments were conducted to investigate the effects of plant density, plant genotype and N fertilization on the light absorption and light extinction of sunflower (Helianthus annuus L.) and canola (Brassica napus L.). A detailed set of plant growth, light absorption and crop yield and oil related parameters were determined. Light was measured at noon during the sunny days with clear sky. In experiment I, although the plant density (PD) of 14 resulted in the highest rate of sunflower light absorption (31.37%) and light extinction (0.756), the highest rate of grain yield and grain oil yield was resulted at PD12 at 3639 and 1457.9kg/ha, respectively; as well as by genotype SUP.A. In experiment II (canola), PD80 resulted in the highest rate of light absorption (13.13%), light extinction (0.63), grain yield (2189.4kg/ha) and grain oil yield (556.54kg/ha). This was also the case for Genotype H. In experiment III (canola), although N150 resulted in the highest rate of light absorption (10.74%) and light extinction (0.48), the highest rate of grain yield (3413.6kg/ha) and grain oil yield (891.86kg/ha) was resulted at N100 as well as by Genotype H401. Results indicate how light properties, crop growth and yield of sunflower and canola can be affected by plant and environmental parameters, which are also of practical use by farmers. Copyright © 2017 Elsevier B.V. All rights reserved.

Optimization of Supercritical CO2 Extraction of Fish Oil from Viscera of African Catfish (Clarias gariepinus)

PubMed Central

Sarker, Mohamed Zaidul Islam; Selamat, Jinap; Habib, Abu Sayem Md. Ahsan; Ferdosh, Sahena; Akanda, Mohamed Jahurul Haque; Jaffri, Juliana Mohamed

2012-01-01

Fish oil was extracted from the viscera of African Catfish using supercritical carbon dioxide (SC-CO2). A Central Composite Design of Response Surface methodology (RSM) was employed to optimize the SC-CO2 extraction parameters. The oil yield (Y) as response variable was executed against the four independent variables, namely pressure, temperature, flow rate and soaking time. The oil yield varied with the linear, quadratic and interaction of pressure, temperature, flow rate and soaking time. Optimum points were observed within the variables of temperature from 35 °C to 80 °C, pressure from 10 MPa to 40 MPa, flow rate from 1 mL/min to 3 mL/min and soaking time from 1 h to 4 h. However, the extraction parameters were found to be optimized at temperature 57.5 °C, pressure 40 MPa, flow rate 2.0 mL/min and soaking time 2.5 h. At this optimized condition, the highest oil yields were found to be 67.0% (g oil/100 g sample on dry basis) in the viscera of catfish which was reasonable to the yields of 78.0% extracted using the Soxhlet method. PMID:23109854

Characterization of protease from bacillus sp. on medium containing FeCl3 exposed to magnetic field 0.2 mt

NASA Astrophysics Data System (ADS)

Sumardi; Agustrina, Rochmah; Nugroho Ekowati, Christina; Selvie Pasaribu, Yovita

2018-03-01

This purpose of this research is to determine the character of the protease enzymes from Bacillus sp. on media content of FeCl3 exposed to 0.2 mT magnetic field. The data obtained were analyzed descriptively. The result showed that protease enzyme without Fe resulted in the highest activity at pH 8, temperature. 30°C with the addition of activator Mn2+, and Vmax of 0.28 U/ml, and Km of 4.60 U/ml. The protease enzyme on media without magnetic field exposure and containing Fe yielded the highest activity at pH 8, temperature 30°C with the addition of activator Mn2+, and Vmax of 0.33 U/ml, and Km of 5.64 U/ml. The protease enzyme on medium with magnetic field exposure and use Fe as inductors have the highest activity at pH 9, the temperature of 55° C with the addition of activator Mn2+, and Vmax of 0.35 U/ml, and Km 10.04 U/ml.

Diversity and physiological characterization of D-xylose-fermenting yeasts isolated from the Brazilian Amazonian Forest.

PubMed

Cadete, Raquel M; Melo, Monaliza A; Dussán, Kelly J; Rodrigues, Rita C L B; Silva, Silvio S; Zilli, Jerri E; Vital, Marcos J S; Gomes, Fátima C O; Lachance, Marc-André; Rosa, Carlos A

2012-01-01

This study is the first to investigate the Brazilian Amazonian Forest to identify new D-xylose-fermenting yeasts that might potentially be used in the production of ethanol from sugarcane bagasse hemicellulosic hydrolysates. A total of 224 yeast strains were isolated from rotting wood samples collected in two Amazonian forest reserve sites. These samples were cultured in yeast nitrogen base (YNB)-D-xylose or YNB-xylan media. Candida tropicalis, Asterotremella humicola, Candida boidinii and Debaryomyces hansenii were the most frequently isolated yeasts. Among D-xylose-fermenting yeasts, six strains of Spathaspora passalidarum, two of Scheffersomyces stipitis, and representatives of five new species were identified. The new species included Candida amazonensis of the Scheffersomyces clade and Spathaspora sp. 1, Spathaspora sp. 2, Spathaspora sp. 3, and Candida sp. 1 of the Spathaspora clade. In fermentation assays using D-xylose (50 g/L) culture medium, S. passalidarum strains showed the highest ethanol yields (0.31 g/g to 0.37 g/g) and productivities (0.62 g/L · h to 0.75 g/L · h). Candida amazonensis exhibited a virtually complete D-xylose consumption and the highest xylitol yields (0.55 g/g to 0.59 g/g), with concentrations up to 25.2 g/L. The new Spathaspora species produced ethanol and/or xylitol in different concentrations as the main fermentation products. In sugarcane bagasse hemicellulosic fermentation assays, S. stipitis UFMG-XMD-15.2 generated the highest ethanol yield (0.34 g/g) and productivity (0.2 g/L · h), while the new species Spathaspora sp. 1 UFMG-XMD-16.2 and Spathaspora sp. 2 UFMG-XMD-23.2 were very good xylitol producers. This study demonstrates the promise of using new D-xylose-fermenting yeast strains from the Brazilian Amazonian Forest for ethanol or xylitol production from sugarcane bagasse hemicellulosic hydrolysates.

Possible correlation between levansucrase production and probiotic activity of Bacillus sp. isolated from honey and honey bee.

PubMed

Hamdy, Abdelhamid A; Elattal, Nouran A; Amin, Magdy A; Ali, Amal E; Mansour, Nahla M; Awad, Ghada E A; Awad, Hassan M; Esawy, Mona A

2017-04-01

Five bacterial isolates from honey and bee gut were selected based on their high levansucrase activity and levan yield which were strongly positively correlated. All isolates showed good tolerance to temperature up to 70 °C, to NaCl up to 3 M and to 0.1% H 2 O 2 . They maintained over 59 and 64% survival at pH 9.0 and 2.0 respectively, but showed varying tolerance to 0.1% bile salts and pancreatic enzymes. Most isolates were susceptible to widely used antibiotics, but demonstrated diverse antimicrobial activity. Non hemolytic isolates were identified on the basis of 16S rRNA sequencing as Bacillus subtilis HMNig-2 and B. subtilis MENO2 with 97% homology. They exhibited promising probiotic characteristics and achieved highest levansucrase activity of 94.1 and 81.5 U/mL respectively. Both exhibited highest biofilm formation ability in static microtiter plate assay. Also, they achieved 34 and 26% adhesion respectively to Caco-2cells and had highest free radical scavenging activity of 30.8 and 26.2% respectively. The levans of the two isolates showed good antimicrobial activity against some pathogens and exhibited positive prebiotic effect (prebiotic index >1) with Lactobacillus casei and Lactobacillus reuteri. Results suggest a correlation between levansucrase production, levan yield and pre-probiotic activities of the studied strains.

Optimization of pH, temperature and CaCl2 concentrations for Ricotta cheese production from Buffalo cheese whey using Response Surface Methodology.

PubMed

Rashid, Abdul Ahid; Huma, Nuzhat; Zahoor, Tahir; Asgher, Muhammad

2017-02-01

The recovery of milk constituents from cheese whey is affected by various processing conditions followed during production of Ricotta cheese. The objective of the present investigation was to optimize the temperature (60-90 °C), pH (3-7) and CaCl2 concentration (2·0-6·0 mm) for maximum yield/recovery of milk constituents. The research work was carried out in two phases. In 1st phase, the influence of these processing conditions was evaluated through 20 experiments formulated by central composite design (CCD) keeping the yield as response factor. The results obtained from these experiments were used to optimize processing conditions for maximum yield using response surface methodology (RSM). The three best combinations of processing conditions (90 °C, pH 7, CaCl2 6 mm), (100 °C, pH 5, CaCl2 4 mm) and (75 °C, pH 8·4, CaCl2 4 mm) were exploited in the next phase for Ricotta cheese production from a mixture of Buffalo cheese whey and skim milk (9 : 1) to determine the influence of optimized conditions on the cheese composition. Ricotta cheeses were analyzed for various physicochemical (moisture, fat, protein, lactose, total solids, pH and acidity indicated) parameters during storage of 60 d at 4 ± 2 °C after every 15 d interval. Ricotta cheese prepared at 90 °C, pH 7 and CaCl2 6 mm exhibited the highest cheese yield, proteins and total solids, while high fat content was recorded for cheese processed at 100 °C, pH 5 and 4 mm CaCl2 concentration. A significant storage-related increase in acidity and NPN was recorded for all cheese samples.

Effects of associated bacteria on the pathogenicity and reproduction of the insect-parasitic nematode Rhabditis blumi (Nematoda: Rhabditida).

PubMed

Park, Hae Woong; Kim, Yong Ook; Ha, Jae-Seok; Youn, Sung Hun; Kim, Hyeong Hwan; Bilgrami, Anwar L; Shin, Chul Soo

2011-09-01

Three bacteria, Alcaligenes faecalis , Flavobacterium sp., and Providencia vermicola , were isolated from dauer juveniles of Rhabditis blumi . The pathogenic effects of the bacteria against 4th instar larvae of Galleria mellonella were investigated. Providencia vermicola and Flavobacterium sp. showed 100% mortality at 48 h after haemocoelic injection, whereas A. faecalis showed less than 30% mortality. Dauer juveniles showed 100% mortality against G. mellonella larvae, whereas axenic juveniles, which do not harbor associated bacteria, exhibited little mortality. All of the associated bacteria were used as a food source for nematode growth, and nematode yield differed with bacterial species. Among the bacterial species, P. vermicola was most valued for nematode yield, showing the highest yield of 5.2 × 10(4) nematodes/mL in the plate. In bacterial cocultures using two of the three associated bacteria, one kind stimulated the other. The highest total bacterial yield of 12.6 g/L was obtained when the inoculum ratio of P. vermicola to A. faecalis was 10:1. In air-lift bioreactors, the nematode growth rate increased with an increasing level of dissolved oxygen. The maximum nematode yield of 1.75 × 10(5) nematodes/mL was obtained at 192 h with an aeration rate of 6 vvm.

Subcritical ethanol extraction of flavonoids from Moringa oleifera leaf and evaluation of antioxidant activity.

PubMed

Wang, Yongqiang; Gao, Yujie; Ding, Hui; Liu, Shejiang; Han, Xu; Gui, Jianzhou; Liu, Dan

2017-03-01

A large-scale process to extract flavonoids from Moringa oleifera leaf by subcritical ethanol was developed and HPLC-MS analysis was conducted to qualitatively identify the compounds in the extracts. To optimize the effects of process parameters on the yield of flavonoids, a Box-Behnken design combined with response surface methodology was conducted in the present work. The results indicated that the highest extraction yield of flavonoids by subcritical ethanol extraction could reach 2.60% using 70% ethanol at 126.6°C for 2.05h extraction. Under the optimized conditions, flavonoids yield was substantially improved by 26.7% compared with the traditional ethanol reflux method while the extraction time was only 2h, and obvious energy saving was observed. FRAP and DPPH assays showed that the extracts had strong antioxidant and free radical scavenging activities. Copyright © 2016 Elsevier Ltd. All rights reserved.

Two-stage anaerobic digestion of sugar beet silage: The effect of the pH-value on process parameters and process efficiency.

PubMed

Kumanowska, Elzbieta; Uruñuela Saldaña, Mariana; Zielonka, Simon; Oechsner, Hans

2017-12-01

The study investigated the influence of the target pH-values 4.5, 5, 5.5 and 6 in the acidification reactor on process parameters, such as substrate-specific methane yield and the intermediates, in the two-stage anaerobic digestion of sugar beet silage. The total specific methane yield (Nlkg -1 CODd -1 ) increased with an increase in the pH (pH 4.5: 140.58±70.08, pH 5: 181.21±55.71, pH 5.5: 218.32±51.01, pH 6: 256.47±28.78). The pH-value also had an effect on the dominant intermediate in hydrolysate. At the pH-value of 4.5, almost no acidification and microbial activity was observed. At pH 5 and 5.5, butyric acid production dominated, guided by H 2 production. At pH 6 acetic acid was the main product. The absence of H 2 and the highest SMY makes it favorable under practical aspects. Copyright © 2017 Elsevier Ltd. All rights reserved.

Liquid smoke characteristics from the pyrolysis of oil palm fronds

NASA Astrophysics Data System (ADS)

Maulina, S.; Silia, F.

2018-02-01

This study was conducted as means to characterize the pyrolysis of oil palm fronds into more economical products. In particular, this study was focused on pyrolysis of oil palm fronds, which could generate products such as liquid smoke, tar and char. Four characteristics of liquid smoke were examined in this study, namely the yield of liquid smoke, phenolic content, total acid content and pH. These characteristics were examined in a temperature of 150 °C, 200 °C and 250 °C with processing time of 60 minutes, 90 minutes and 120 minutes. This study revealed that the highest yield of liquid smoke was equal to 43.47% at a temperature of 150 °C for approximately 2 hours, while the highest level of phenolic was obtained at a temperature of 250 °C for approximately 1 hour. Moreover, the highest total acid content obtained was 11.23% at a temperature of 150 °C with a time of 1 hour. In addition, all operating conditions has produced liquid smoke with an average pH value of 3.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sievers, David A.; Kuhn, Erik M.; Tucker, Melvin P.

In this study, the reaction conditions used during dilute-acid pretreatment of lignocellulosic biomass control the carbohydrate digestion yield and also hydrolyzate properties. Depending on the conversion route of interest, solid-liquid separation (SLS) may be required to split the hemicellulose-rich liquor from the cellulose-rich insoluble solids, and slurry properties are important for SLS. Corn stover was pretreated at different reaction conditions and the slurries were assessed for conversion yield and filtration performance. Increasing pretreatment temperature reduced the solids mean particle size and resulted in slower slurry filtration rates when vacuum filtered or pressure filtered. Corn stover pretreated at 165 °C formore » 10 min and with 1% H 2SO 4 exhibited the highest xylose yield and best filtration performance with a no-wash filtration rate of 80 kg/h m 2 and cake permeability of 15 x 10 -15.« less

Biohydrogen from thermophilic co-fermentation of swine manure with fruit and vegetable waste: maximizing stable production without pH control.

PubMed

Tenca, A; Schievano, A; Perazzolo, F; Adani, F; Oberti, R

2011-09-01

Hydrogen production by dark fermentation may suffer of inhibition or instability due to pH deviations from optimality. The co-fermentation of promptly degradable feedstock with alkali-rich materials, such as livestock wastes, may represent a feasible and easy to implement approach to avoid external adjustments of pH. Experiments were designed to investigate the effect of the mixing ratio of fruit-vegetable waste with swine manure with the aim of maximizing biohydrogen production while obtaining process stability through the endogenous alkalinity of manure. Fruit-vegetable/swine manure ratio of 35/65 and HRT of 2d resulted to give the highest production rate of 3.27 ± 0.51 L(H2)L(-1)d(-1), with a corresponding hydrogen yield of 126 ± 22 mL(H2)g(-1)(VS-added) and H2 content in the biogas of 42 ± 5%. At these operating conditions the process exhibited also one of the highest measured stability, with daily productions deviating for less than 14% from the average. Copyright © 2011 Elsevier Ltd. All rights reserved.

Formation of pyrophosphate on hydroxyapatite with thioesters as condensing agents

NASA Technical Reports Server (NTRS)

Weber, A. L.

1982-01-01

'Energy-rich' thioesters are shown to act as condensing agents in the formation of pyrophosphate on hydroxyapatite in the presence of water at ambient temperature. The yield of pyrophosphate based on thioester ranges from 2.5% to 11.4% and depends upon the pH and concentration of reactants. Reaction of 0.130 M hydroxyapatite suspended in a solution of 0.08 M sodium phosphate and 0.20 M imidazole hydrochloride (pH 7.0) with 0.10 M N,S-diacetylcysteamine for 6 days gives the highest yield of pyrophosphate (11.4%). Pyrophosphate formation requires the presence of hydroxyapatite, sodium phosphate and the thioester, N,S-diacetylcysteamine. The related thioester, N,S-diacetylcysteine, also yields pyrophosphate in reactions on hydroxyapatite.

Blowpipe Mineralogy for Physics/Environment: Highest-Possible-Tc SC Quest; BOTH PERMANENT FOREVER Carb-IDES SOLID-State Sequestration AND Drought(s)-Elimination

NASA Astrophysics Data System (ADS)

Segler, Kurt; Williams, W.; Siegel, E.

2010-03-01

Detailed are old blowpipe[Kraus,Hunt,Ramsdell, Mineralogy (1936)] new applications:charcoal-block reduction of borates to yield (``N-NW'' of MgB2) Overhauser-[PR 35,1,411(1987); Intl.J.Mod.Phys.1,2 & 4,927(1987)]-``land'' predicted high-EST- POSSIBLE Tc SC ˜ ``LiD2''; very-early: Siegel[Phys.Stat.Sol.(a) 11,45(1972);Semiconductors & Insulators 5: 39,47,62(1979)] carb- IDES SOLID-state phase-TRANSITIONED CHEMICALLY-REDOX"-REACTED STABLE PERMANENT LONG-term STRATEGY, NOT ``CO2" BUT NON-gas Carbon-``ELEMENT"-sequestration: PROFITABLE MARKETABLE SALEABLE VALUABLE USEFUL ``Grab and Sell" TRUMPS ``cap and trade"!!!; Mott alloying/vertical metal-insulator transitions in ``borax-(GLASS)- beads"; and very-early Siegel [3rd Intl.Conf.Alt.Energy,Hemi- sphere/Springer(1980)-vol.5/p.459] ``FLYING-WATER" ``Hindenberg- effect"(H2-UP;H2O-DOWN) via H2-maximal-Archimedes-buoyancy ``chemical-rain-in-piplines", only via Siegel GMR enabled diffusive-magnetoresistance(DMR)enabled Siegel proprietary ``magnetic-H-valve": Renewables-H2-H2O purposely flexible versatile agile scaleable retrofitable integrated operating- system for PERMANENT drought(s)-elimination FOREVER!!!

Production of volatile fatty acids from sewage organic matter by combined bioflocculation and alkaline fermentation.

PubMed

Khiewwijit, Rungnapha; Temmink, Hardy; Labanda, Alvaro; Rijnaarts, Huub; Keesman, Karel J

2015-12-01

This study explored the potential of volatile fatty acids (VFA) production from sewage by a combined high-loaded membrane bioreactor and sequencing batch fermenter. VFA production was optimized with respect to SRT and alkaline pH (pH 8-10). Application of pH shock to a value of 9 at the start of a sequencing batch cycle, followed by a pH uncontrolled phase for 7days, gave the highest VFA yield of 440mgVFA-COD/g VSS. This yield was much higher than at fermentation without pH control or at a constant pH between 8 and 10. The high yield in the pH 9 shocked system could be explained by (1) a reduction of methanogenic activity, or (2) a high degree of solids degradation or (3) an enhanced protein hydrolysis and fermentation. VFA production can be further optimized by fine-tuning pH level and longer operation, possibly allowing enrichment of alkalophilic and alkali-tolerant fermenting microorganisms. Copyright © 2015 Elsevier Ltd. All rights reserved.

High liquid fuel yielding biofuel processes and a roadmap for the future transportation

NASA Astrophysics Data System (ADS)

Singh, Navneet R.

In a fossil-fuel deprived world when crude oil will be scarce and transportation need cannot be met with electricity and transportation liquid fuel must be produced, biomass derived liquid fuels can be a natural replacement. However, the carbon efficiency of the currently known biomass to liquid fuel conversion processes ranges from 35-40%, yielding 90 ethanol gallon equivalents (ege) per ton of biomass. This coupled with the fact that the efficiency at which solar energy is captured by biomass (<1%) is significantly lower than H 2 (10-27%) and electricity (20-42%), implies that sufficient land area is not available to meet the need for the entire transportation sector. To counter this dilemma, a number of processes have been proposed in this work: a hybrid hydrogen-carbon (H2CAR) process based on biomass gasification followed by the Fischer-Tropsch process such that 100% carbon efficiency is achieved yielding 330 ege/ton biomass using hydrogen derived from a carbon-free energy. The hydrogen requirement for the H2CAR process is 0.33 kg/liter of diesel. To decrease the hydrogen requirement associated with the H2CAR process, a hydrogen bio-oil (H2Bioil) process based on biomass fast-hydropyrolysis/hydrodeoxygenation is proposed which can achieve liquid fuel yield of 215 ege/ton consuming 0.11 kg hydrogen per liter of oil. Due to the lower hydrogen consumption of the H2Bioil process, synergistically integrated transition pathways are feasible where hot syngas derived from coal gasification (H2Bioil-C) or a natural gas reformer (H 2Bioil-NG) is used to supply the hydrogen and process heat for the biomass fast-hydropyrolysis/hydrodeoxygenation. Another off-shoot of the H2Bioil process is the H2Bioil-B process, where hydrogen required for the hydropyrolysis is obtained from gasification of a fraction of the biomass. H2Bioil-B achieves the highest liquid fuel yield (126-146 ege/ton of biomass) reported in the literature for any self-contained conversion of biomass to biofuel. Finally, an integration of the H2Bioil process with the H2CAR process is suggested which can achieve 100% carbon efficiency (330 ege/ton of biomass) at the expense of 0.24 kg hydrogen/liter of oil. A sun-to-fuel efficiency analysis shows that extracting CO2 from air and converting it to liquid fuel is at least two times more efficient than growing dedicated fuel crops and converting them to liquid fuel even for the highest biomass growth rates feasible by algae. This implies that liquid fuel should preferably be produced from sustainably available waste (SAW) biomass first and if the SAW biomass is unable to meet the demand for liquid fuel, then, CO2 should be extracted from air and converted to liquid fuel, rather than growing biomass. Furthermore, based on the Sun-to-Wheels recovery for different transportation pathways, synergistic and complementary use of electricity, hydrogen and biomass, all derived from solar energy, is presented in an energy efficient roadmap to successfully propel the entire future transportation sector.

Synthesis and spectroscopic properties of some new difluoroboron bis-β-diketonate derivatives.

PubMed

Pi, Yan; Wang, Dun-Jia; Liu, Hua; Hu, Yan-Jun; Wei, Xian-Hong; Zheng, Jing

2014-10-15

Six new bis-β-diketones (RCOCH2CO-C7H7N-COCH2COR) were synthesized from 3,5-diacetyl-2,6-dimethylpyridine via Claisen condensation with the corresponding esters, and then reacted with boron trifluoride etherate to afford difluoroboron bis-β-diketonate derivatives. Their spectroscopic properties were investigated by UV-vis, FTIR, (1)H NMR and fluorescence spectroscopic techniques. It was found that these boron complexes exhibited violet or blue fluorescence emission at 422-445nm and possessed high extinction coefficients. The results indicate that the extending π-conjugation can increase the fluorescence intensity and quantum yield for these boron complexes. Especially, the compound 2b displayed the stronger fluorescence intensity and the highest fluorescence quantum yield (Φu=0.94) in these boron compounds. However, compounds 2c and 2d had the lower fluorescence intensity and quantum yield as a result of the heavy atom effect of the chlorine atom in the molecules. Copyright © 2014 Elsevier B.V. All rights reserved.

Synthesis and spectroscopic properties of some new difluoroboron bis-β-diketonate derivatives

NASA Astrophysics Data System (ADS)

Pi, Yan; Wang, Dun-Jia; Liu, Hua; Hu, Yan-Jun; Wei, Xian-Hong; Zheng, Jing

2014-10-01

Six new bis-β-diketones (RCOCH2CO-C7H7N-COCH2COR) were synthesized from 3,5-diacetyl-2,6-dimethylpyridine via Claisen condensation with the corresponding esters, and then reacted with boron trifluoride etherate to afford difluoroboron bis-β-diketonate derivatives. Their spectroscopic properties were investigated by UV-vis, FTIR, 1H NMR and fluorescence spectroscopic techniques. It was found that these boron complexes exhibited violet or blue fluorescence emission at 422-445 nm and possessed high extinction coefficients. The results indicate that the extending π-conjugation can increase the fluorescence intensity and quantum yield for these boron complexes. Especially, the compound 2b displayed the stronger fluorescence intensity and the highest fluorescence quantum yield (Φu = 0.94) in these boron compounds. However, compounds 2c and 2d had the lower fluorescence intensity and quantum yield as a result of the heavy atom effect of the chlorine atom in the molecules.

The effect of pre-treatments to the nickel limonite leaching using dissolved gaseous SO2-air

NASA Astrophysics Data System (ADS)

Wulandari, W.; Soerawidjaja, T. H.; Alifiani, D.; Rangga, D. A.

2018-01-01

Nickel limonite leaching has been subjected to a number of studies, one of the method is by using dissolved gaseous SO2-air. The selectivity of nickel over iron extracted from leaching using dissolved gaseous SO2-air is advantageous, however the nickel that can be recovered is limited. This paper studies pre-treatments that is applied to the nickel ore prior leaching in order to increase the recovery of dissolved nickel from nickel limonite ore. There two pre-treatments that were carried out in this research, roasting and alkali-roasting using Na2CO3. The extraction was carried out for 180 min with pH 2, 3, 4, and 5 and temperature 30, 55, and 80 °C. It is found that the highest yield is achieved at pH 2 and 80 °C with nickel recovery of 61.39%. At pH 2, for alkali-roasting pre-treatment, the nickel yield raised from 28.17% to 100% and for roasting pre-treatment the nickel yield increased from 20.42% to 61.39%. However, at pH 2, the nickel to iron selectivity decreased from 96272 to 534 for roasting pre-treatment and from 1.8 to 1 for alkali-roasting pre-treatment.

Evaluation of pretreatment methods on mixed inoculum for both batch and continuous thermophilic biohydrogen production from cassava stillage.

PubMed

Luo, Gang; Xie, Li; Zou, Zhonghai; Wang, Wen; Zhou, Qi

2010-02-01

Anaerobic sludges, pretreated by chloroform, base, acid, heat and loading-shock, as well as untreated sludge were evaluated for their thermophilic fermentative hydrogen-producing characters from cassava stillage in both batch and continuous experiments. Results showed that the highest hydrogen production was obtained by untreated sludge and there were significant differences (p<0.05) in hydrogen yields (varied from 32.9 to 65.3mlH(2)/gVS) among the tested pretreatment methods in batch experiments. However, the differences in hydrogen yields disappeared in continuous experiments, which indicated the pretreatment methods had only short-term effects on the hydrogen production. Further study showed that alkalinity was a crucial parameter influencing the fermentation process. When the influent was adjusted to pH 6 by NaHCO(3) instead of NaOH, the hydrogen yield increased from about 40 to 52mlH(2)/gVS in all the experiments. Therefore, pretreatment of anaerobic sludge is unnecessary for practical thermophilic fermentative hydrogen production from cassava stillage.

Synthesis of furfural from xylose, xylan, and biomass using AlCl3·6H2O in biphasic media via xylose isomerization to xylulose.

PubMed

Yang, Yu; Hu, Chang-Wei; Abu-Omar, Mahdi M

2012-02-13

Furfural was prepared in high yields (75 %) from the reaction of xylose in a water-tetrahydrofuran biphasic medium containing AlCl(3)·6H2O and NaCl under microwave heating at 140 °C. The reaction profile revealed the formation of xylulose as an intermediate en route to the dehydration product (furfural). The reaction under these conditions reached completion in 45 min. The aqueous phase containing AlCl(3)·6H(2)O and NaCl could be recycled multiple times (>5) without any loss of activity or selectivity for furfural. Extension of this biphasic reaction system to include xylan as the starting material afforded furfural in 64 % yield. The use of corn stover, pinewood, switchgrass, and poplar gave furfural in 55, 38, 56, and 64 % yield, respectively, at 160 °C. Even though AlCl(3)·6H(2)O did not affect the conversion of crystalline cellulose, moderate yields of the by-product 5-hydroxymethylfurfural (HMF) were noted. The highest HMF yield of 42 % was obtained from pinewood. The coproduction of HMF and furfural from biomass was attributed to the weakening of the cellulose network in the biomass, as a result of hemicellulose hydrolysis. The multifunctional capacity of AlCl(3)·6H(2)O (hemicellulose hydrolysis, xylose isomerization, and xylulose dehydration) in combination with its ease of recyclability make it an attractive candidate/catalyst for the selective synthesis of furfural from various biomass feedstocks. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The impact of particle size and initial solid loading on thermochemical pretreatment of wheat straw for improving sugar recovery.

PubMed

Rojas-Rejón, Oscar A; Sánchez, Arturo

2014-07-01

This work studies the effect of initial solid load (4-32 %; w/v, DS) and particle size (0.41-50 mm) on monosaccharide yield of wheat straw subjected to dilute H(2)SO(4) (0.75 %, v/v) pretreatment and enzymatic saccharification. Response surface methodology (RSM) based on a full factorial design (FFD) was used for the statistical analysis of pretreatment and enzymatic hydrolysis. The highest xylose yield obtained during pretreatment (ca. 86 %; of theoretical) was achieved at 4 % (w/v, DS) and 25 mm. The solid fraction obtained from the first set of experiments was subjected to enzymatic hydrolysis at constant enzyme dosage (17 FPU/g); statistical analysis revealed that glucose yield was favored with solids pretreated at low initial solid loads and small particle sizes. Dynamic experiments showed that glucose yield did not increase after 48 h of enzymatic hydrolysis. Once established pretreatment conditions, experiments were carried out with several initial solid loading (4-24 %; w/v, DS) and enzyme dosages (5-50 FPU/g). Two straw sizes (0.41 and 50 mm) were used for verification purposes. The highest glucose yield (ca. 55 %; of theoretical) was achieved at 4 % (w/v, DS), 0.41 mm and 50 FPU/g. Statistical analysis of experiments showed that at low enzyme dosage, particle size had a remarkable effect over glucose yield and initial solid load was the main factor for glucose yield.

Optimization of antioxidant activity by response surface methodology in hydrolysates of jellyfish (Rhopilema esculentum) umbrella collagen.

PubMed

Zhuang, Yong-liang; Zhao, Xue; Li, Ba-fang

2009-08-01

To optimize the hydrolysis conditions to prepare hydrolysates of jellyfish umbrella collagen with the highest hydroxyl radical scavenging activity, collagen extracted from jellyfish umbrella was hydrolyzed with trypsin, and response surface methodology (RSM) was applied. The optimum conditions obtained from experiments were pH 7.75, temperature (T) 48.77 degrees C, and enzyme-to-substrate ratio ([E]/[S]) 3.50%. The analysis of variance in RSM showed that pH and [E]/[S] were important factors that significantly affected the process (P<0.05 and P<0.01, respectively). The hydrolysates of jellyfish umbrella collagen were fractionated by high performance liquid chromatography (HPLC), and three fractions (HF-1>3000 Da, 1000 Da

Optimization of antioxidant activity by response surface methodology in hydrolysates of jellyfish (Rhopilema esculentum) umbrella collagen*

PubMed Central

Zhuang, Yong-liang; Zhao, Xue; Li, Ba-fang

2009-01-01

To optimize the hydrolysis conditions to prepare hydrolysates of jellyfish umbrella collagen with the highest hydroxyl radical scavenging activity, collagen extracted from jellyfish umbrella was hydrolyzed with trypsin, and response surface methodology (RSM) was applied. The optimum conditions obtained from experiments were pH 7.75, temperature (T) 48.77 °C, and enzyme-to-substrate ratio ([E]/[S]) 3.50%. The analysis of variance in RSM showed that pH and [E]/[S] were important factors that significantly affected the process (P<0.05 and P<0.01, respectively). The hydrolysates of jellyfish umbrella collagen were fractionated by high performance liquid chromatography (HPLC), and three fractions (HF-1>3000 Da, 1000 Da

Effect of medium components on the production of a biosurfactant from Candida tropicalis applied to the removal of hydrophobic contaminants in soil.

PubMed

Batista, Ranielly M; Rufino, Raquel D; Luna, Juliana M; de Souza, José Edson G; Sarubbo, Leonie A

2010-05-01

The influence of medium constituents on the production of biosurfactants by Candida tropicalis cultivated in waste frying oil was investigated according to a fractional factorial 2(5-1) design. The combined effect of the C/N(inorganic), C/Fe, C/Mg, and C/P ratios and yeast extract on surface tension reduction, biosurfactant yield, emulsification activity, and biomass were studied. The highest biosurfactant yield was reached when low C/Mg and low C/P ratio variables were combined, while the cell growth was favored by increasing the nitrogen concentration. The highest surface tension net decrease, on the other hand, was observed at low yeast extract concentration, low C/Fe, and high C/P ratios. Emulsification indices against lubrication and automobile waste oil of approximately 65 to 95% were observed. The crude biosurfactant produced in the medium--formulated with 2% waste frying oil, 0.067% NH4Cl, 0.025% MgSO4.7H2O, 0.067% KH2PO4, and 0.0026% FeCl3.6H2O--removed approximately 78 to 97% of the petroleum and motor oil adsorbed in sand samples.

Acidogenic digestion of food waste in a thermophilic leach bed reactor: Effect of pH and leachate recirculation rate on hydrolysis and volatile fatty acid production.

PubMed

Hussain, Abid; Filiatrault, Mélissa; Guiot, Serge R

2017-12-01

The effect of pH control (4, 5, 6, 7) on volatile fatty acids (VFA) production from food waste was investigated in a leach bed reactor (LBR) operated at 50°C. Stabilisation of pH at 7 resulted in hydrolysis yield of 530g soluble chemical oxygen demand (sCOD)/kg total volatile solids (TVS) added and VFA yield of 247gCOD/kg TVS added, which were highest among all pH tested. Butyric acid dominated the VFA mix (49-54%) at pH of 7 and 6, while acetate composed the primary VFA (41-56%) at pH of 4 and 5. A metabolic shift towards lactic acid production was observed at pH of 5. Improving leachate recirculation rate further improved the hydrolysis and degradation efficiency by 10-16% and the acidification yield to 340gCOD/kgTVS added. The butyric acid concentration of 16.8g/L obtained at neutral pH conditions is among the highest reported in literature. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

Factors affecting the formation of iodo-trihalomethanes during oxidation with chlorine dioxide.

PubMed

Guo, Wanhong; Shan, Yingchun; Yang, Xin

2014-01-15

Effects of water characteristics, reaction time, temperature, bromide and iodide ion concentrations, oxidant doses, and pH on formation of iodinated trihalomethanes (I-THM) during oxidation of iodide-containing water with chlorine dioxide (ClO2) were investigated. Among the water samples collected from ten water sources, iodoform (CHI3) was the predominant I-THM and trace amount of chlorodiiodomethane (CHClI2) was occasionally found. CHI3 yields correlated moderately with specific UV absorbance (SUVA) (R(2)=0.79), indicating that hydrophobic aromatic content were important precursors. Longer reaction time led to continued formation of CHI3. I-THM containing bromide was also found in waters containing both bromide and iodide, but CHI3 was dominant. The formation of CHI3 was higher at 25°C than 5°C and 35°C. CHI3 formation showed an increase followed by a decrease trend with increasing ClO2 doses and iodide concentrations and the highest yields occurred at iodide to ClO2 molar ratios of 1-2. pH 8 resulted in the highest CHI3 formation. It should be noted that a high iodide concentration was spiked to waters before adding ClO2 and the results may not reflect the formation yields of iodinated THMs in real conditions, but they provide information about formation trend of I-THM during oxidation of ClO2. Copyright © 2013 Elsevier B.V. All rights reserved.

Application of a novel enzymatic pretreatment using crude hydrolytic extracellular enzyme solution to microalgal biomass for dark fermentative hydrogen production.

PubMed

Yun, Yeo-Myeong; Kim, Dong-Hoon; Oh, You-Kwan; Shin, Hang-Sik; Jung, Kyung-Won

2014-05-01

In this study, a novel enzymatic pretreatment of Chlorella vulgaris for dark fermentative hydrogen production (DFHP) was performed using crude hydrolytic extracellular enzyme solution (CHEES) extracted from the H2 fermented effluent of food waste. It was found that the enzyme extracted at 52 h had the highest hydrolysis efficiency of microalgal biomass, resulting in the highest H2 yield of 43.1 mL H2/g dry cell weight along with shorter lag periods. Even though a high amount of VFAs was accumulated in CHEES, especially butyrate, the fermentative bacteria on the DFHP was not affected from product inhibition. It also appears that the presence of organic acids, especially lactate and acetate, contained in the CHEES facilitated enhancement of H2 production acted as a co-substrate. Therefore, all of the experimental results suggest that the enhancement of DFHP performance caused by CHEES has a dual role as the hydrolysis enhancer and the co-substrate supplier. Copyright © 2014 Elsevier Ltd. All rights reserved.

Pretreatment of spent mushroom substrate for enhancing the conversion of fermentable sugar.

PubMed

Wu, Songqing; Lan, Yanjiao; Wu, Zhimao; Peng, Yan; Chen, Siqi; Huang, Zhipeng; Xu, Lei; Gelbič, Ivan; Guan, Xiong; Zhang, Lingling; Zou, Shuangquan

2013-11-01

To develop a cost-effective biopesticide, spent mushroom substrate (SMS) extract was studied as a potential carbon source for cultivating Bacillus thuringiensis (Bt). Several pretreatments were compared to determine the optimal method for degrading cellulose to produce reducing sugars, including dilute sulfuric acid (0.5-2.0% v/v, 50-121°C, 1h), sodium hydroxide (0.5-2% w/v, 50-121°C, 1h), calcium hydroxide (0.2-4% w/v, 50-121°C, 1h), and hot water (50-121°C, 1h). Pretreatment was followed by standard enzymatic hydrolysis and fermentation. Results showed that the highest cellulose degradation was obtained using 2% dilute sulfuric acid pretreatment at 121°C for 1h, resulting in a high yield of reducing sugar (284.24 g/kg SMS). Sporulation was also highest using the same pretreatment. Use of SMS is not only an alternative way to commercialize Bt-based biopesticide, but also a potential solution for the environmental pollution associated with accumulation of the spent substrate of the mushroom industry. Copyright © 2013 Elsevier Ltd. All rights reserved.

Extraction of aucubin from seeds of Eucommia ulmoides Oliv. using supercritical carbon dioxide.

PubMed

Li, Hui; Hu, Jiangyu; Ouyang, Hui; Li, Yanan; Shi, Hui; Ma, Chengjin; Zhang, Yongkang

2009-01-01

Supercritical CO2 was used as solvent for the extraction of aucubin from the seeds of Eucommia ulmoides Oliv. The co-solvent composition was tested and extraction conditions were optimized. Results showed that the best co-solvent was a water-ethanol mixture (1 + 3, v/v), and the highest yield was obtained when the extraction was performed under 26 MPa at extraction and separation temperatures of 55 and 30 degrees C for 120 min, using 6 mL co-solvent/g material at a CO2 flow rate of 20 L/h. In a comparison of the supercritical CO2 and Soxhlet extraction methods, the Soxhlet method needed 3 h to extract 10 g material, whereas the supercritical CO2 extraction technique needed only 2 h to extract 100 g material, thus showing a high extraction capability. The supercritical CO2 extraction produced a higher yield, with a lower cost for the extraction. Owing to the advantages of low extraction temperature, high yield, and ease of separating the product from the solvent, supercritical CO2 extraction is likely to be developed into an ideal technique for the extraction of aucubin, a compound with thermal instability, from the seeds of this plant.

Biomass fast pyrolysis in a fluidized bed reactor under N2, CO2, CO, CH4 and H2 atmospheres.

PubMed

Zhang, Huiyan; Xiao, Rui; Wang, Denghui; He, Guangying; Shao, Shanshan; Zhang, Jubing; Zhong, Zhaoping

2011-03-01

Biomass fast pyrolysis is one of the most promising technologies for biomass utilization. In order to increase its economic potential, pyrolysis gas is usually recycled to serve as carrier gas. In this study, biomass fast pyrolysis was carried out in a fluidized bed reactor using various main pyrolysis gas components, namely N(2), CO(2), CO, CH(4) and H(2), as carrier gases. The atmosphere effects on product yields and oil fraction compositions were investigated. Results show that CO atmosphere gave the lowest liquid yield (49.6%) compared to highest 58.7% obtained with CH(4). CO and H(2) atmospheres converted more oxygen into CO(2) and H(2)O, respectively. GC/MS analysis of the liquid products shows that CO and CO(2) atmospheres produced less methoxy-containing compounds and more monofunctional phenols. The higher heating value of the obtained bio-oil under N(2) atmosphere is only 17.8 MJ/kg, while that under CO and H(2) atmospheres increased to 23.7 and 24.4 MJ/kg, respectively. Copyright © 2010 Elsevier Ltd. All rights reserved.

Effect of dilution and ash supplement on the bio-methane potential of palm oil mill effluent (POME)

NASA Astrophysics Data System (ADS)

Jijai, Sunwanee; Muleng, Saina; Siripatana, Chairat

2017-08-01

This study aimed to evaluate the bio-methane potential of POME at different dilutions (100, 80, 60, 40, and 20 percent of initial POME) and different pH dues to different levels of ash supplement. Five different amounts of ash were added to digesters (0, 2, 4, 6, and 8 grams of ash were added to 170 ml of POME respectively). The digesters were operated in batch anaerobic digestion systems at room temperature (28-30 °C) and the experiments were performed in duplicate manner. The results showed that POME without dilution gave highest cumulative biogas (950 ml). However, 80% dilution from original POME gave the highest methane yield (45.83 mL CH4/ gCODadded or 103.13 mL CH4/ gCODremoved). Finally, the results of experiment 2, this adding ash into POME increased pH as well as enhanced the biogas production. It was found that adding ash at the ash:POME ratio of 2 g: 170 ml gave the highest both the cumulative biogas and methane yield (1,520 mL and 218.79 mL CH4/ gCODremoved respectively). The addition of ash in the raw waste of POME gave the pH in the range of criteria and highest bio-methane potential. The modified Gompertz equation, Schnute as well as Monod kinetic models were used to compare the data from the experiments. It was found that the factors that affected included, the bio-methane production and the kinetic parameters (the maximum specific methane production rates (Rm ml/day) and the methane production potential (P, mL)), initial COD, nutrients, levels of dilution, and initial pH (by adding different level of ash). However, λ (lag phase period) was not affected by initial COD and other factors. While Monod kinetics provides valuable insight in explaining what could happen behind the systematic trends.

[Effects of different irrigation treatments during heading and flowering stage on cold resis-tance, yield and physiological characteristics of late rice].

PubMed

Cao, Na; Chen, Xiao Rong; He, Hao Hua; Zhu, Chang Lan; Cai, Shuo; Xu, Tao; Xie, Heng Wang; Liu, Fang Ping

2017-12-01

Taking super hybrid rice variety 'Wufengyou T025' as test material, the effects of different irrigation methods and water layer depth on physiological characteristics and yield in double-season late rice under low temperature conditions during heading and flowering stage were investigated. Three treatments were set, i.e., draining during day and containing 4-5 cm water layer during night (H 1 ), draining during day and containing 8-10 cm water layer during night (H 2 ), and containing 8-10 cm water layer day and night (H 3 ), with the 0-1 cm water layer day and night was as the control (CK). The results showed that rice leaf temperature, soil layer temperature and canopy temperature under the different irrigation treatments were higher than that of CK, and the warming effect of treatment H 2 was the best during the low temperature period. Leaf chlorophyll content, net photosynthetic rate, transpiration rate, leaf stomatal conductance and intercellular CO 2 concentration of rice plants decreased gradually under the low temperature, while the smallest reduction occurred in H 2 . The increase ranges of malondialdehyde and proline content in H 2 were lower, while its soluble protein content was the highest compared with other irrigation treatments. The increase ranges for the activities of superoxide dismutase and peroxidase in H 2 were lower, while its decrease range for the activity of catalase was the lowest. Irrigation for heat preservation could increase the yield, and H 2 performed best. Yield of H 2 at the second sowing date in 2014 and 2015 encountering low temperature increased by 12.9% and 13.5% respectively compared to CK. The yield components including the effective panicle numbers per plant, panicle length, seed setting rate and 1000-grain mass were improved in all irrigation treatments compared to CK. Draining during day and containing 8-10 cm water layer during night (H 2 ) was the most effective agronomic measure to enhance the tolerance to low temperature during heading and flowering stage for double-season hybrid late rice.

Characteristics of Pyrolytic Topping in Fluidized Bed for Different Volatile Coals

NASA Astrophysics Data System (ADS)

Xiong, R.; Dong, L.; Xu, G. W.

Coal is generally combusted or gasified directly to destroy completely the chemical structures, such as aromatic rings containing in volatile coals including bituminite and lignite. Coal topping refers to a process that extracts chemicals with aromatic rings from such volatile coals in advance of combustion or gasification and thereby takes advantage of the value of coal as a kind of chemical structure resource. CFB boiler is the coal utilization facility that can be easily retrofitted to implement coal topping. A critical issue for performing coal topping is the choice of the pyrolytic reactor that can be different types. The present study concerns fluidized bed reactor that has rarely been tested for use in coal topping. Two different types of coals, one being Xiaolongtan (XLT) lignite and the other Shanxi (SX) bituminous, were tested to clarify the yield and composition of pyrolysis liquid and gas under conditions simulating actual operations. The results showed that XLT lignite coals had the maximum tar yield in 823-873K and SX bituminite realized its highest tar yield in 873-923K. Overall, lignite produced lower tar yield than bituminous coal. The pyrolysis gas from lignite coals contained more CO and CO2 and less CH4, H2 and C2+C3 (C2H4, C2H6, C3H6, C3H8) components comparing to that from bituminous coal. TG-FTIR analysis of tars demonstrated that for different coals there are different amounts of typical chemical species. Using coal ash of CFB boiler, instead of quartz sand, as the fluidized particles decreased the yields of both tar and gas for all the tested coals. Besides, pyrolysis in a reaction atmosphere simulating the pyrolysis gas (instead of N2) resulted also in higher production of pyrolysis liquid.

Effects of dilute-acid pretreatment conditions on filtration performance of corn stover hydrolyzate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sievers, David A.; Kuhn, Erik M.; Tucker, Melvin P.

In this study, the reaction conditions used during dilute-acid pretreatment of lignocellulosic biomass control the carbohydrate digestion yield and also hydrolyzate properties. Depending on the conversion route of interest, solid-liquid separation (SLS) may be required to split the hemicellulose-rich liquor from the cellulose-rich insoluble solids, and slurry properties are important for SLS. Corn stover was pretreated at different reaction conditions and the slurries were assessed for conversion yield and filtration performance. Increasing pretreatment temperature reduced the solids mean particle size and resulted in slower slurry filtration rates when vacuum filtered or pressure filtered. Corn stover pretreated at 165 °C formore » 10 min and with 1% H 2SO 4 exhibited the highest xylose yield and best filtration performance with a no-wash filtration rate of 80 kg/h m 2 and cake permeability of 15 x 10 -15.« less

Effects of dilute-acid pretreatment conditions on filtration performance of corn stover hydrolyzate

DOE PAGES

Sievers, David A.; Kuhn, Erik M.; Tucker, Melvin P.; ...

2017-06-28

In this study, the reaction conditions used during dilute-acid pretreatment of lignocellulosic biomass control the carbohydrate digestion yield and also hydrolyzate properties. Depending on the conversion route of interest, solid-liquid separation (SLS) may be required to split the hemicellulose-rich liquor from the cellulose-rich insoluble solids, and slurry properties are important for SLS. Corn stover was pretreated at different reaction conditions and the slurries were assessed for conversion yield and filtration performance. Increasing pretreatment temperature reduced the solids mean particle size and resulted in slower slurry filtration rates when vacuum filtered or pressure filtered. Corn stover pretreated at 165 °C formore » 10 min and with 1% H 2SO 4 exhibited the highest xylose yield and best filtration performance with a no-wash filtration rate of 80 kg/h m 2 and cake permeability of 15 x 10 -15.« less

Formation of glycosidases in batch and continuous culture of Bacteroides fragilis.

PubMed Central

Berg, J O; Nord, C E; Wadström, T

1978-01-01

Nine strains of bacteroides fragilis were cultivated in stirred fermentors and tested for their ability to produce glycosidases. B. fragilis subsp. vulgatus B70 was used for optimizing the production of glycosidases. The highest bacterial yield was obtained in proteose peptone-yeast extract medium. The optimum pH for maximal bacterial yield was 7.0, and the optimum temperature for growth was 37 degrees C. The formation of glycosidases was optimal between pH 6.5 and 7.5, and the optimum temperature for synthesis of glycosidases was between 33 and 37 degrees C. Culture under controlled conditions in fermentors gave more reproducible production of glycosidases than static cultures in bottles. The strain was also grown in continuous culture at a dilution rate of 0.1 liter/h at pH 7.0 and 37 degrees C with a yield of 2.0 mg of dry weight per ml in the complex medium. The formation of glycosidases remained constant during the entire continuous process. PMID:25044

The modeling of ethanol production by Kluyveromyces marxianus using whey as substrate in continuous A-Stat bioreactors.

PubMed

Gabardo, Sabrina; Pereira, Gabriela Feix; Rech, Rosane; Ayub, Marco Antônio Záchia

2015-09-01

We investigated the kinetics of whey bioconversion into ethanol by Kluyveromyces marxianus in continuous bioreactors using the "accelerostat technique" (A-stat). Cultivations using free and Ca-alginate immobilized cells were evaluated using two different acceleration rates (a). The kinetic profiles of these systems were modeled using four different unstructured models, differing in the expressions for the specific growth (μ) and substrate consumption rates (r s), taking into account substrate limitation and product inhibition. Experimental data showed that the dilution rate (D) directly affected cell physiology and metabolism. The specific growth rate followed the dilution rate (μ≈D) for the lowest acceleration rate (a = 0.0015 h(-2)), condition in which the highest ethanol yield (0.52 g g(-1)) was obtained. The highest acceleration rate (a = 0.00667 h(-2)) led to a lower ethanol yield (0.40 g g(-1)) in the system where free cells were used, whereas with immobilized cells ethanol yields increased by 23 % (0.49 g g(-1)). Among the evaluated models, Monod and Levenspiel combined with Ghose and Tyagi models were found to be more appropriate for describing the kinetics of whey bioconversion into ethanol. These results may be useful in scaling up the process for ethanol production from whey.

Biodegradation of pesticide triclosan by A. versicolor in simulated wastewater and semi-synthetic media.

PubMed

Ertit Taştan, Burcu; Dönmez, Gönül

2015-02-01

Triclosan is known as an antimicrobial agent, a powerful bacteriostat and an important pesticide. In this paper biodegradation of triclosan by Aspergillus versicolor was investigated. Effects of simulated wastewater and semi-synthetic media on fungal triclosan degradation process were detected. HPLC analysis showed that fungal triclosan biodegradation yield was 71.91% at about 7.5 mg/L concentration in semi-synthetic medium and was 37.47% in simulated wastewater. Fungus could be able to tolerate the highest triclosan concentration (15.69 mg/L). The biodegradation yield was 29.81% and qm was 2.22 mg/g at this concentration. Some of the parameters, such as pH, culture media, increasing triclosan and biomass concentrations were optimized in order to achieve the effective triclosan biodegradation process. The highest triclosan biodegradation yields of all microorganisms were achieved by A. versicolor. Copyright © 2014 Elsevier Inc. All rights reserved.

Dilute alkali pretreatment of softwood pine: A biorefinery approach.

PubMed

Safari, Ali; Karimi, Keikhosro; Shafiei, Marzieh

2017-06-01

Dilute alkali pretreatment was performed on softwood pine to maximize ethanol and biogas production via a biorefinery approach. Alkali pretreatments were performed with 0-2% w/v NaOH at 100-180°C for 1-5h. The liquid fraction of the pretreated substrates was subjected to anaerobic digestion. The solid fraction of the pretreatment was used for separate enzymatic hydrolysis and fermentation. High ethanol yields of 76.9‒78.0% were achieved by pretreatment with 2% (w/v) NaOH at 180°C. The highest biogas yield of 244mL/g volatile solid (at 25°C, 1bar) was achieved by the pretreatment with 1% (w/v) NaOH at 180°C. The highest gasoline equivalent (sum of ethanol and methane) of 197L per ton of pinewood and the lowest ethanol manufacturing cost of 0.75€/L was obtained after pretreatment with 1% NaOH at 180°C for 5h. The manufacturing cost of ethanol from untreated wood was 4.12€/L. Copyright © 2017 Elsevier Ltd. All rights reserved.

Delignification of disposable wooden chopsticks waste for fermentative hydrogen production by an enriched culture from a hot spring.

PubMed

Phummala, Kanthima; Imai, Tsuyoshi; Reungsang, Alissara; Chairattanamanokorn, Prapaipid; Sekine, Masahiko; Higuchi, Takaya; Yamamoto, Koichi; Kanno, Ariyo

2014-06-01

Hydrogen (H2) production from lignocellulosic materials may be enhanced by removing lignin and increasing the porosity of the material prior to enzymatic hydrolysis. Alkaline pretreatment conditions, used to delignify disposable wooden chopsticks (DWC) waste, were investigated. The effects of NaOH concentration, temperature and retention time were examined and it was found that retention time had no effect on lignin removal or carbohydrate released in enzymatic hydrolysate. The highest percentage of lignin removal (41%) was obtained with 2% NaOH at 100°C, correlated with the highest carbohydrate released (67 mg/g pretreated DWC) in the hydrolysate. An enriched culture from a hot spring was used as inoculum for fermentative H2 production, and its optimum initial pH and temperature were determined to be 7.0 and 50°C, respectively. Furthermore, enzymatic hydrolysate from pretreated DWC was successfully demonstrated as a substrate for fermentative H2 production by the enriched culture. The maximum H2 yield and production rate were achieved at 195 mL H2/g total sugars consumed and 116 mL H2/(L·day), respectively. Copyright © 2014 The Research Centre for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

Behaviors of glucose decomposition during acid-catalyzed hydrothermal hydrolysis of pretreated Gelidium amansii.

PubMed

Jeong, Tae Su; Choi, Chang Ho; Lee, Ji Ye; Oh, Kyeong Keun

2012-07-01

Acid-catalyzed hydrothermal hydrolysis is one path to cellulosic glucose and subsequently to its dehydration end products such as hydroxymethyl furfural (HMF), formic acid and levulinic acid. The effect of sugar decomposition not only lowers the yield of fermentable sugars but also forms decomposition products that inhibit subsequent fermentation. The present experiments were conducted with four different acid catalysts (H(2)SO(4), HNO(3), HCl, and H(3)PO(4)) at various acid normalities (0.5-2.1N) in batch reactors at 180-210 °C. From the results, H(2)SO(4) was the most suitable catalyst for glucose production, but glucose decomposition occurred during the hydrolysis. The glucose production was maximized at 160.7 °C, 2.0% (w/v) H(2)SO(4), and 40 min, but resulted in a low glucan yield of 33.05% due to the decomposition reactions, which generated formic acid and levulinic acid. The highest concentration of levulinic acid, 7.82 g/L, was obtained at 181.2 °C, 2.0% (w/v) H(2)SO(4), and 40 min. Copyright © 2012 Elsevier Ltd. All rights reserved.

Impact of pH and butyric acid on butanol production during batch fermentation using a new local isolate of Clostridium acetobutylicum YM1.

PubMed

Al-Shorgani, Najeeb Kaid Nasser; Kalil, Mohd Sahaid; Yusoff, Wan Mohtar Wan; Hamid, Aidil Abdul

2018-02-01

The effect of pH and butyric acid supplementation on the production of butanol by a new local isolate of Clostridium acetobutylicum YM1 during batch culture fermentation was investigated. The results showed that pH had a significant effect on bacterial growth and butanol yield and productivity. The optimal initial pH that maximized butanol production was pH 6.0 ± 0.2. Controlled pH was found to be unsuitable for butanol production in strain YM1, while the uncontrolled pH condition with an initial pH of 6.0 ± 0.2 was suitable for bacterial growth, butanol yield and productivity. The maximum butanol concentration of 13.5 ± 1.42 g/L was obtained from cultures grown under the uncontrolled pH condition, resulting in a butanol yield ( Y P / S ) and productivity of 0.27 g/g and 0.188 g/L h, respectively. Supplementation of the pH-controlled cultures with 4.0 g/L butyric acid did not improve butanol production; however, supplementation of the uncontrolled pH cultures resulted in high butanol concentrations, yield and productivity (16.50 ± 0.8 g/L, 0.345 g/g and 0.163 g/L h, respectively). pH influenced the activity of NADH-dependent butanol dehydrogenase, with the highest activity obtained under the uncontrolled pH condition. This study revealed that pH is a very important factor in butanol fermentation by C. acetobutylicum YM1.

One-pot, one-step synthesis of 2,5-diformylfuran from carbohydrates over Mo-containing Keggin heteropolyacids.

PubMed

Liu, Yu; Zhu, Liangfang; Tang, Jinqiang; Liu, Mingyang; Cheng, Ruodi; Hu, Changwei

2014-12-01

In this work, a one-pot strategy for directly converting fructose into 2,5-diformylfuran (DFF) over Mo-containing Keggin heteropolyacids (HPAs) in open air is developed. H3 PMo12 O40 HPA is found to show high activity and selectivity to the formation of DFF owing to its higher Brønsted acidity and moderate redox potential. The partial substitution of the H(+) in H3 PMo12 O40 with Cs(+) leads to the heterogenization of the HPA by forming its cesium salts Csx H3-x PMo12 (x=0.5, 1.5, and 2.5). A satisfactory yield of 69.3% to DFF is obtained over Cs0.5 H2.5 PMo12 polyoxometalate after deliberate optimization of the reaction conditions. The heterogenized polyoxometalate could be recycled and reused without significant loss of catalytic activity for five runs. The produced DFF could be separated from the resulting mixture by an adsorption-desorption method using activated carbon as the adsorbent and furfural as the desorbent. A highest isolated yield of 58.2% is obtained. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Production and Characterization of Highly Thermostable β-Glucosidase during the Biodegradation of Methyl Cellulose by Fusarium oxysporum

PubMed Central

Olajuyigbe, Folasade M.; Nlekerem, Chidinma M.; Ogunyewo, Olusola A.

2016-01-01

Production of β-glucosidase from Fusarium oxysporum was investigated during degradation of some cellulosic substrates (Avicel, α-cellulose, carboxymethyl cellulose (CMC), and methylcellulose). Optimized production of β-glucosidase using the cellulosic substrate that supported highest yield of enzyme was examined over 192 h fermentation period and varied pH of 3.0–11.0. The β-glucosidase produced was characterized for its suitability for industrial application. Methyl cellulose supported the highest yield of β-glucosidase (177.5 U/mg) at pH 6.0 and 30°C at 96 h of fermentation with liberation of 2.121 μmol/mL glucose. The crude enzyme had optimum activity at pH 5.0 and 70°C. The enzyme was stable over broad pH range of 4.0–7.0 with relative residual activity above 60% after 180 min of incubation. β-glucosidase demonstrated high thermostability with 83% of its original activity retained at 70°C after 180 min of incubation. The activity of β-glucosidase was enhanced by Mn2+ and Fe2+ with relative activities of 167.67% and 205.56%, respectively, at 5 mM and 360% and 315%, respectively, at 10 mM. The properties shown by β-glucosidase suggest suitability of the enzyme for industrial applications in the improvement of hydrolysis of cellulosic compounds into fermentable sugars that can be used in energy generation and biofuel production. PMID:26977320

Catalytic EGR-Loop Reforming for High Efficiency in a Stoichiometric SI Engine through TCR and Dilution Limit Extension. 1. Catalyst Performance and Fuel Effects

DOE PAGES

Chang, Yan; Szybist, James P.; Pihl, Josh A.; ...

2017-12-19

The use of fuel reformate from catalytic processes is known to have beneficial effects on the spark-ignited (SI) combustion process through enhanced dilution tolerance and decreased combustion duration, but in many cases reformate generation can incur a significant fuel penalty. Here, in this two-part investigation, we demonstrate that efficient catalytic fuel reforming can result in improved brake engine efficiency while maintaining stoichiometric exhaust under the right conditions. In part one of this investigation, we used a combination of thermodynamic equilibrium calculations and experimental fuel catalytic reforming measurements on an engine to characterize the best possible reforming performance and energetics overmore » a range of equivalence ratios and O 2 concentrations. Ideally, one might expect the highest levels of thermochemical recuperation for the highest catalyst equivalence ratios. However, reforming under these conditions is highly endothermic, and the available enthalpy for reforming is constrained. Thus for relatively high equivalence ratios, more methane and less H 2 and CO are produced. Our experiments revealed that this suppression of H 2 and CO could be countered by adding small amounts of O 2, yielding as much as 15 vol % H 2 at the catalyst outlet for 4 < Φ catalyst < 7 under quasi-steady-state conditions. Under these conditions the H 2 and CO yields were highest and there was significant water consumption, confirming the presence of steam reforming reactions. Analyses of the experimental catalyst measurements indicated the possibility of both endothermic and exothermic reaction stages and global reaction rates sufficient to enable the utilization of higher space velocities than those employed in our experiments. Finally, in a companion paper detailing part two of this investigation, we present results for the engine dilution tolerance and brake engine efficiency impacts of the reforming levels achieved.« less

Catalytic EGR-Loop Reforming for High Efficiency in a Stoichiometric SI Engine through TCR and Dilution Limit Extension. 1. Catalyst Performance and Fuel Effects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chang, Yan; Szybist, James P.; Pihl, Josh A.

The use of fuel reformate from catalytic processes is known to have beneficial effects on the spark-ignited (SI) combustion process through enhanced dilution tolerance and decreased combustion duration, but in many cases reformate generation can incur a significant fuel penalty. Here, in this two-part investigation, we demonstrate that efficient catalytic fuel reforming can result in improved brake engine efficiency while maintaining stoichiometric exhaust under the right conditions. In part one of this investigation, we used a combination of thermodynamic equilibrium calculations and experimental fuel catalytic reforming measurements on an engine to characterize the best possible reforming performance and energetics overmore » a range of equivalence ratios and O 2 concentrations. Ideally, one might expect the highest levels of thermochemical recuperation for the highest catalyst equivalence ratios. However, reforming under these conditions is highly endothermic, and the available enthalpy for reforming is constrained. Thus for relatively high equivalence ratios, more methane and less H 2 and CO are produced. Our experiments revealed that this suppression of H 2 and CO could be countered by adding small amounts of O 2, yielding as much as 15 vol % H 2 at the catalyst outlet for 4 < Φ catalyst < 7 under quasi-steady-state conditions. Under these conditions the H 2 and CO yields were highest and there was significant water consumption, confirming the presence of steam reforming reactions. Analyses of the experimental catalyst measurements indicated the possibility of both endothermic and exothermic reaction stages and global reaction rates sufficient to enable the utilization of higher space velocities than those employed in our experiments. Finally, in a companion paper detailing part two of this investigation, we present results for the engine dilution tolerance and brake engine efficiency impacts of the reforming levels achieved.« less

Thermodynamical and structural insights of orange II adsorption by Mg{sub R}AlNO{sub 3} layered double hydroxides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mustapha Bouhent, Mohamed; Laboratoire des Materiaux Inorganiques, UMR CNRS 6002, Universite Blaise Pascal, F-63177 Aubiere Cedex; Derriche, Zoubir, E-mail: derriche_zoubir@yahoo.co

2011-05-15

[Mg{sub 1-x} Al{sub x}(OH){sub 2}][(NO{sub 3}){sub x}, nH{sub 2}O] Layered Double Hydroxide (LDH) sorbents with variable Mg/Al molar (R=(1-x)/x) ratios were investigated for adsorption of azo dye, orange II (OII) at various pH and temperature conditions. Mg{sub 2}AlNO{sub 3} displays the highest adsorption capacity with 3.611 mmol of OII per gram of Mg{sub 2}AlNO{sub 3} at 40 {sup o}C. Adsorption isotherms have been fitted using the Langmuir model and free energy of adsorption ({Delta}G{sup o}), enthalpy ({Delta}H{sup o}) and entropy ({Delta}S{sup o}) were calculated. The experimental values for {Delta}G{sup o} in temperature range between 10 and 40 {sup o}C weremore » found to be negative indicating that a spontaneous process occurred. Positive calculated enthalpy values, characteristic of an endothermic process were found. Characterization of solids (PXRD, FTIR, UV-vis, TGA/DTA, adsorption isotherm BET analysis, SEM and Zetametry) before and after adsorption showed that adsorption proceeds in two steps. First, adsorption occurs at the LDH surface, followed by intercalation via anion exchange. -- Graphical Abstract: Structural and thermodynamical insight of adsorption/Intercalation of OII in Mg{sub R}Al LDH Display Omitted Highlights: {yields} The nitrate containing hydrotalcite-like compounds (Mg{sub R}AlNO{sub 3} LDH) were prepared by the coprecipitation method. {yields} Adsorption of anionic orange dye(OII) is studied on LDHs at different temperatures. {yields} The adsorption process is well described by the Langmuir isotherm model. {yields} Mg{sub 2}AlNO{sub 3} displays the highest adsorption capacity with 3.611 mmol of OII per gram of Mg{sub 2}AlNO{sub 3} at 40 {sup o}C. {yields} Adsorption process does not occur on the surface of the LDH only but an intercalation process is also occurring concomitantly according to the thermodynamical values.« less

Phenotypic Stability of Zea mays Grain Yield and Its Attributing Traits under Drought Stress

PubMed Central

Ali, Fawad; Ahsan, Muhammad; Ali, Qurban; Kanwal, Naila

2017-01-01

Phenotypic stability under stress environment facilitate the fitness of genotype and opens new horizons to explore the cryptic genetic variation. Variation in tolerance to drought stress, a major grain yield constraint to global maize production, was identified, at the phenotypic and genotypic level. Here we found a prominent hybrid H9 that showed fitness over four growing seasons for grain yield under water stress conditions. Genotypic and phenotypic correlation of yield attributing traits over four seasons demonstrated that cobs per plant, 100 seed weight, number of grains rows per cob, total dry matter, cob diameter had positive association (r2 = 0.3–0.9) to grain yield. The perturbation was found for chlorophyll content as it showed moderate to strong association (P < 0.01) over four seasons, might be due to environment or genotype dependent. Highest heritability (95%) and genetic advance (79%) for grain yield was found in H9 over four consecutive crop growing seasons. Combined analysis over four seasons showed that studied variables together explained 85% of total variation in dependent structure (grain yield) obtained by Principal component analysis. This significant finding is the best example of phenotypic stability of grain yield in H9 and made it best fitted for grain yield under drought stress scenario. Detailed genetic analysis of H9 will help us to identify significant loci and alleles that made H9 the best fitted and it could serve as a potential source to generate novel transgressive levels of tolerance for drought stress in arid/semiarid regions. PMID:28878785

Phenotypic Stability of Zea mays Grain Yield and Its Attributing Traits under Drought Stress.

PubMed

Ali, Fawad; Ahsan, Muhammad; Ali, Qurban; Kanwal, Naila

2017-01-01

Phenotypic stability under stress environment facilitate the fitness of genotype and opens new horizons to explore the cryptic genetic variation. Variation in tolerance to drought stress, a major grain yield constraint to global maize production, was identified, at the phenotypic and genotypic level. Here we found a prominent hybrid H 9 that showed fitness over four growing seasons for grain yield under water stress conditions. Genotypic and phenotypic correlation of yield attributing traits over four seasons demonstrated that cobs per plant, 100 seed weight, number of grains rows per cob, total dry matter, cob diameter had positive association ( r 2 = 0.3-0.9) to grain yield. The perturbation was found for chlorophyll content as it showed moderate to strong association ( P < 0.01) over four seasons, might be due to environment or genotype dependent. Highest heritability (95%) and genetic advance (79%) for grain yield was found in H 9 over four consecutive crop growing seasons. Combined analysis over four seasons showed that studied variables together explained 85% of total variation in dependent structure (grain yield) obtained by Principal component analysis. This significant finding is the best example of phenotypic stability of grain yield in H 9 and made it best fitted for grain yield under drought stress scenario. Detailed genetic analysis of H 9 will help us to identify significant loci and alleles that made H 9 the best fitted and it could serve as a potential source to generate novel transgressive levels of tolerance for drought stress in arid/semiarid regions.

2-Thiophenecarboxylic acid hydrazide Derivatives: Synthesis and Anti-Tuberculosis Studies

NASA Astrophysics Data System (ADS)

Fahmi, M. R. G.; Khumaidah, L.; Ilmiah, T. K.; Fadlan, A.; Santoso, M.

2018-04-01

One of the most frequent and widespread infectious diseases especially in developing countries is tuberculosis (TB). The number of TB drug resistant tend to increase, and there has been no new TB drug introduce since the 1960s. Six 2-Thiophenecarboxylic acid hydrazide derivatives were synthesized in 90-97% yields, and 2-thiophenecarbonylhydrazone-5, 7-dibromoisatin showed the highest activity in inhibiting M. tuberculosis H37Rv.

Conversion of acid hydrolysate of oil palm empty fruit bunch to L-lactic acid by newly isolated Bacillus coagulans JI12.

PubMed

Ye, Lidan; Hudari, Mohammad Sufian Bin; Zhou, Xingding; Zhang, Dongxu; Li, Zhi; Wu, Jin Chuan

2013-06-01

Cost-effective conversion of lignocellulose hydrolysate to optically pure lactic acid is commercially attractive but very challenging. Bacillus coagulans JI12 was isolated from natural environment and used to produce L-lactic acid (optical purity > 99.5 %) from lignocellulose sugars and acid hydrolysate of oil palm empty fruit bunch (EFB) at 50 °C and pH 6.0 without sterilization of the medium. In fed-batch fermentation with 85 g/L initial xylose and 55 g/L xylose added after 7.5 h, 137.5 g/L lactic acid was produced with a yield of 98 % and a productivity of 4.4 g/L h. In batch fermentation of a sugar mixture containing 8.5 % xylose, 1 % glucose, and 1 % L-arabinose, the lactic acid yield and productivity reached 98 % and 4.8 g/L h, respectively. When EFB hydrolysate was used, 59.2 g/L of lactic acid was produced within 9.5 h at a yield of 97 % and a productivity of 6.2 g/L h, which are the highest among those ever reported from lignocellulose hydrolysates. These results indicate that B. coagulans JI12 is a promising strain for industrial production of L-lactic acid from lignocellulose hydrolysate.

Generation of Oxidants From the Reaction of Nanoparticulate Zero-Valent Iron and Oxygen for the use in Contaminant Remediation

NASA Astrophysics Data System (ADS)

Keenan, C. R.; Lee, C.; Sedlak, D. L.

2007-12-01

The reaction of zero-valent iron (ZVI) with oxygen can lead to the formation of oxidants, which may be used to transform recalcitrant contaminants including non-polar organics and certain metals. Nanoparticulate iron might provide a practical mechanism of remediating oxygen-containing groundwater and contaminated soil. To gain insight into the reaction mechanism and to quantify the yield of oxidants, experiments were performed with model organic compounds in the presence of nanoparticulate zero-valent iron and oxygen. At pH values below 5, ZVI nanoparticles were oxidized within 30 minutes with a stoichiometry of approximately two Fe0 oxidized per O2 consumed. Using the oxidation of methanol and ethanol to formaldehyde and acetaldehyde, respectively, we found that less than 2% of the consumed oxygen was converted to reactive oxidants under acidic conditions. The yield of aldehydes increased with pH up to pH 7, with maximum oxidant yields of around 5% relative to the mass of ZVI added. The increase of aldehyde yield with pH was attributable to changes in the processes responsible for oxidant production. At pH values below 5, the corrosion of ZVI by oxygen produces hydrogen peroxide, which subsequently reacts with ferrous iron [Fe(II)] via the Fenton reaction. At higher pH values, the aldehydes are produced when Fe(II), the initial product of ZVI oxidation, reacts with oxygen. The decrease in oxidant yield at pH values above 7 may be attributable to precipitation of Fe(II). The oxidation of benzoic acid and 2-propanol to para-hydroxybenzoic acid and acetone, respectively, followed a very different trend compared to the primary alcohols. In both cases, the highest product yields (approximately 2% with respect to ZVI added) were observed at pH 3. Yields decreased with increasing pH, with no oxidized product detected at neutral pH. These results suggest that two different oxidants may be produced by the system: hydroxyl radical (OH-·) at acidic pH and a more selective oxidant such as the ferryl ion [Fe(IV)] at neutral pH. This provides insight into the type of compounds that may be oxidized using the zero-valent iron and oxygen system. The addition of certain compounds such as oxalate and polyoxometalate (POM) may improve contaminant remediation efficiencies by enhancing oxidant yields. The introduction of 1 mM oxalate improved the formaldehyde yield by approximately 20% at neutral pH. Oxalate accelerates the Fenton reaction and limits the passivation of the ZVI surface by increasing iron solubility. The presence of excess POM greatly enhanced the yield of formaldehyde, with maximum yields of 60 and 35% with respect to ZVI added at pH 2 and 7, respectively. The mechanism of POM enhancement is a function of solution pH. At acidic pH, POM acts an electron shuttle by directly transferring electrons from ZVI to oxygen to increase the hydrogen peroxide production. At neutral pH, POM may act by forming soluble iron-complexes and preventing the build-up of an iron oxide layer on the ZVI surface.

Pretreatment of Dried Distiller Grains with Solubles by Soaking in Aqueous Ammonia and Subsequent Enzymatic/Dilute Acid Hydrolysis to Produce Fermentable Sugars.

PubMed

Nghiem, Nhuan P; Montanti, Justin; Kim, Tae Hyun

2016-05-01

Dried distillers grains with solubles (DDGS), a co-product of corn ethanol production in the dry-grind process, was pretreated by soaking in aqueous ammonia (SAA) using a 15 % w/w NH4OH solution at a solid/liquid ratio of 1:10. The effect of pretreatment on subsequent enzymatic hydrolysis was studied at two temperatures (40 and 60 °C) and four reaction times (6, 12, 24, and 48 h). Highest glucose yield of 91 % theoretical was obtained for the DDGS pretreated at 60 °C and 24 h. The solubilized hemicellulose in the liquid fraction was further hydrolyzed with dilute H2SO4 to generate fermentable monomeric sugars. The conditions of acid hydrolysis included 1 and 4 wt% acid, 60 and 120 °C, and 0.5 and 1 h. Highest yields of xylose and arabinose were obtained at 4 wt% acid, 120 °C, and 1 h. The fermentability of the hydrolysate obtained by enzymatic hydrolysis of the SAA-pretreated DDGS was demonstrated in ethanol fermentation by Saccharomyces cerevisiae. The fermentability of the hydrolysate obtained by consecutive enzymatic and dilute acid hydrolysis was demonstrated using a succinic acid-producing microorganism, strain Escherichia coli AFP184. Under the fermentation conditions, complete utilization of glucose and arabinose was observed, whereas only 47 % of xylose was used. The succinic acid yield was 0.60 g/g total sugar consumed.

Preparation of reactive oxygen scavenging peptides from tilapia (Oreochromis niloticus) skin gelatin: optimization using response surface methodology.

PubMed

Zhuang, Yongliang; Sun, Liping

2011-04-01

Gelatin extracted from tilapia skin was hydrolyzed with Properase E. Response surface methodology (RSM) was applied to optimize the hydrolysis condition (temperature [T], enzyme-to-substrate ratio [E/S], pH and reaction time [t]), to obtain the hydrolysate with the highest hydroxyl radical (•OH) scavenging activity. The optimum conditions obtained were T of 44.2 °C, E/S of 2.2%, pH of 9.2, and t of 3.4 h. The predicted •OH scavenging activity of the hydrolysate under the optimum conditions was 60.7%, and the actually experimental scavenging activity was 60.8%. The hydrolysate was fractionated by ultrafiltration, and 4 fractions were collected. The fraction TSGH4 (MW<2000 Da) showed the strongest •OH scavenging activity with the highest yield. Furthermore, reactive oxygen species (ROS) scavenging activities of TSGH4 with different concentrations were investigated in 5 model systems, including superoxide anion radical (•O2), •OH, hydrogen peroxide (H2O2), peroxynitrite (ONOO-), and nitric oxide (NO•), compared with reduced glutathione (GSH). The results showed that TSGH4 significantly scavenged these ROS, and could be used as a functional ingredient in medicine and food industries.

The efficacy of Beauveria bassiana, jasmonic acid and chlorantraniliprole on larval populations of Helicoverpa armigera in chickpea crop ecosystems.

PubMed

Younas, Aneela; Wakil, Waqas; Khan, Zaeema; Shaaban, Muhammad; Prager, Sean Michael

2017-02-01

A robust integrated pest management (IPM) programme is needed to reduce the use of insecticides in controlling Helicoverpa armigera. Therefore, a 2 year field study was conducted to evaluate the use of alternative control measures (biochemical use) for H. armigera relative to exclusively using chemical insecticides. The entomopathogenic fungus Beauveria bassiana, jasmonic acid and the insecticide chlorantraniliprole were each applied twice during the chickpea growing season. All three applied materials (either alone or combined) significantly (P ≤ 0.05) reduced the larval population of H. armigera and pod infestation. Effects increased with time, and the maximum difference was observed 7 days after the second application in each year. The lowest numbers of larvae per plant and pod infestation were in the B. bassiana 3.21 × 10 6 + chlorantraniliprole treatment in both 2009/2010 and 2010/2011 year. The reduction in the larval population and pod infestation increased chickpea yield and the highest yield in both seasons, and the maximum yield was obtained in the B. bassiana 3.21 × 10 6 + chlorantraniliprole treatment. The populations of natural enemies were highest in the jasmonic acid treatment. The results suggest that B. bassiana, jasmonic acid and chlorantraniliprole may be useful components for the H. armigera IPM strategy. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Environmental conditions affecting exopolysaccharide production by Pseudomonas aeruginosa, Micrococcus sp., and Ochrobactrum sp.

PubMed

Kiliç, Nur Koçberber; Dönmez, Gönül

2008-06-15

Three different chromium-resistant microorganisms (Pseudomonas aeruginosa, Micrococcus sp., and Ochrobactrum sp.) were tested with regard to their EPS production at different pH levels, temperatures, Cr(VI) concentrations, and incubation periods. The optimum pH level was 7 for P. aeruginosa and Micrococcus sp., while it was 8 for Ochrobactrum sp. according to the highest EPS amount at 100 mg/L Cr(VI) concentration. The highest production of EPSs by the three bacteria was obtained under different environmental conditions. P. aeruginosa produced the highest EPS (863.3 mg/L) after incubation for 96 h on media with 50 mg/L Cr(VI) at 20 degrees C, Micrococcus sp. gave the highest yield (444.6 mg/L) after incubation for 72 h on media with 100 mg/L Cr(VI) at the same temperature, and Ochrobactrum sp. had the highest production (430.5 mg/L) on media with 150 mg/L Cr(VI) at 30 degrees C at the end of 48 h of incubation.

Antioxidant Effect and Functional Properties of Hydrolysates Derived from Egg-White Protein

PubMed Central

Cho, Dae-Yeon; Jo, Kyungae; Cho, So Young; Kim, Jin Man; Lim, Kwangsei; Suh, Hyung Joo

2014-01-01

This study utilized commercially available proteolytic enzymes to prepare egg-white protein hydrolysates (EPHs) with different degrees of hydrolysis. The antioxidant effect and functionalities of the resultant products were then investigated. Treatment with Neutrase yielded the most α-amino groups (6.52 mg/mL). Alcalase, Flavourzyme, Protamex, and Ficin showed similar degrees of α-amino group liberation (3.19-3.62 mg/mL). Neutrase treatment also resulted in the highest degree of hydrolysis (23.4%). Alcalase and Ficin treatment resulted in similar degrees of hydrolysis. All hydrolysates, except for the Flavourzyme hydrolysate, had greater radical scavenging activity than the control. The Neutrase hydrolysate showed the highest 2,2-azino-bis-(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) radical scavenging activity (IC50=3.6mg/mL). Therefore, Neutrase was identified as the optimal enzyme for hydrolyzing egg-white protein to yield antioxidant peptides. During Neutrase hydrolysis, the reaction rate was rapid over the first 4 h, and then subsequently declined. The IC50 value was lowest after the first hour (2.99 mg/mL). The emulsifying activity index (EAI) of EPH treated with Neutrase decreased, as the pH decreased. The EPH foaming capacity was maximal at pH 3.6, and decreased at an alkaline pH. Digestion resulted in significantly higher 1,1-diphenyl-2-picrylhydrazyl (DPPH) and ABTS radical scavenging activity. The active peptides released from egg-white protein showed antioxidative activities on ABTS and DHHP radical. Thus, this approach may be useful for the preparation of potent antioxidant products. PMID:26761178

Ammonia formation by the reduction of nitrite/nitrate by FeS: ammonia formation under acidic conditions.

PubMed

Summers, David P

2005-08-01

One issue for the origin of life under a non-reducing atmosphere is the availability of the reduced nitrogen necessary for amino acids, nucleic acids, etc. One possible source of this nitrogen is the formation of ammonia from the reduction of nitrates and nitrites produced by the shock heating of the atmosphere and subsequent chemistry. Ferrous ions will reduce these species to ammonium, but not under acidic conditions. We wish to report results on the reduction of nitrite and nitrate by another source of iron (II), ferrous sulfide, FeS. FeS reduces nitrite to ammonia at lower pHs than the corresponding reduction by aqueous Fe+ 2. The reduction follows a first order decay, in nitrite concentration, with a half-life of about 150 min (room temperature, CO2, pH 6.25). The highest product yield of ammonia measured was 53%. Under CO2, the product yield decreases from pH 5.0 to pH 6.9. The increasing concentration of bicarbonate, at higher pH, interferes with the reaction. Comparing experiments under N2 CO2 shows the interference of bicarbonate. The reaction proceeds well in the presence of such species as chloride, sulfate, and phosphate, though the yield drops significantly with phosphate. FeS also reduces nitrate and, unlike with Fe+ 2, the reduction shows more reproducibility. Again, the product yield decreases with increasing pH, from 7% at pH 4.7 to 0% at pH 6.9. It appears that nitrate is much more sensitive to the presence of added species, perhaps not competing as well for binding sites on the FeS surface. This may be the cause of the lack of reproducibility of nitrate reduction by Fe+ 2 (which also can be sensitive to binding by certain species).

Ammonia Formation By The Reduction Of Nitrite/Nitrate By Fes: Ammonia Formation Under Acidic Conditions

NASA Astrophysics Data System (ADS)

Summers, David P.

2005-08-01

One issue for the origin of life under a non-reducing atmosphere is the availability of the reduced nitrogen necessary for amino acids, nucleic acids, etc. One possible source of this nitrogen is the formation of ammonia from the reduction of nitrates and nitrites produced by the shock heating of the atmosphere and subsequent chemistry. Ferrous ions will reduce these species to ammonium, but not under acidic conditions. We wish to report results on the reduction of nitrite and nitrate by another source of iron (II), ferrous sulfide, FeS. FeS reduces nitrite to ammonia at lower pHs than the corresponding reduction by aqueous Fe+ 2. The reduction follows a first order decay, in nitrite concentration, with a half-life of about 150 min (room temperature, CO2, pH 6.25). The highest product yield of ammonia measured was 53%. Under CO2, the product yield decreases from pH 5.0 to pH 6.9. The increasing concentration of bicarbonate, at higher pH, interferes with the reaction. Comparing experiments under N2 CO2 shows the interference of bicarbonate. The reaction proceeds well in the presence of such species as chloride, sulfate, and phosphate, though the yield drops significantly with phosphate. FeS also reduces nitrate and, unlike with Fe+ 2, the reduction shows more reproducibility. Again, the product yield decreases with increasing pH, from 7% at pH 4.7 to 0% at pH 6.9. It appears that nitrate is much more sensitive to the presence of added species, perhaps not competing as well for binding sites on the FeS surface. This may be the cause of the lack of reproducibility of nitrate reduction by Fe+ 2 (which also can be sensitive to binding by certain species)

Rapid synthesis of propyl caffeate in ionic liquid using a packed bed enzyme microreactor under continuous-flow conditions.

PubMed

Wang, Jun; Gu, Shuang-Shuang; Cui, Hong-Sheng; Yang, Liu-Qing; Wu, Xiang-Yang

2013-12-01

Propyl caffeate has the highest antioxidant activity among caffeic acid alkyl esters, but its industrial production via enzymatic transesterification in batch reactors is hindered by a long reaction time (24h). To develop a rapid process for the production of propyl caffeate in high yield, a continuous-flow microreactor composed of a two-piece PDMS in a sandwich-like microchannel structure was designed for the transesterification of methyl caffeate and 1-propanol catalyzed by Novozym 435 in [B mim][CF3SO3]. The maximum yield (99.5%) in the microreactor was achieved in a short period of time (2.5h) with a flow rate of 2 μL/min, which kinetic constant Km was 16 times lower than that of a batch reactor. The results indicated that the use of a continuous-flow packed bed enzyme microreactor is an efficient method of producing propyl caffeate with an overall yield of 84.0%. Copyright © 2013 Elsevier Ltd. All rights reserved.

Efficient whole cell biocatalyst for formate-based hydrogen production.

PubMed

Kottenhahn, Patrick; Schuchmann, Kai; Müller, Volker

2018-01-01

Molecular hydrogen (H 2 ) is an attractive future energy carrier to replace fossil fuels. Biologically and sustainably produced H 2 could contribute significantly to the future energy mix. However, biological H 2 production methods are faced with multiple barriers including substrate cost, low production rates, and low yields. The C1 compound formate is a promising substrate for biological H 2 production, as it can be produced itself from various sources including electrochemical reduction of CO 2 or from synthesis gas. Many microbes that can produce H 2 from formate have been isolated; however, in most cases H 2 production rates cannot compete with other H 2 production methods. We established a formate-based H 2 production method utilizing the acetogenic bacterium Acetobacterium woodii . This organism can use formate as sole energy and carbon source and possesses a novel enzyme complex, the hydrogen-dependent CO 2 reductase that catalyzes oxidation of formate to H 2 and CO 2 . Cell suspensions reached specific formate-dependent H 2 production rates of 71 mmol g protein -1 h -1 (30.5 mmol g CDW -1 h -1 ) and maximum volumetric H 2 evolution rates of 79 mmol L -1 h -1 . Using growing cells in a two-step closed batch fermentation, specific H 2 production rates reached 66 mmol g CDW -1 h -1 with a volumetric H 2 evolution rate of 7.9 mmol L -1  h -1 . Acetate was the major side product that decreased the H 2 yield. We demonstrate that inhibition of the energy metabolism by addition of a sodium ionophore is suitable to completely abolish acetate formation. Under these conditions, yields up to 1 mol H 2 per mol formate were achieved. The same ionophore can be used in cultures utilizing formate as specific switch from a growing phase to a H 2 production phase. Acetobacterium woodii reached one of the highest formate-dependent specific H 2 productivity rates at ambient temperatures reported so far for an organism without genetic modification and converted the substrate exclusively to H 2 . This makes this organism a very promising candidate for sustainable H 2 production and, because of the reversibility of the A. woodii enzyme, also a candidate for reversible H 2 storage.

Adsorptive removal of fermentation inhibitors from concentrated acid hydrolyzates of lignocellulosic biomass.

PubMed

Sainio, Tuomo; Turku, Irina; Heinonen, Jari

2011-05-01

Adsorptive purification of concentrated acid hydrolyzate of lignocellulose was investigated. Cation exchange resin (CS16GC), neutral polymer adsorbent (XAD-16), and granulated activated carbon (GAC) were studied to remove furfural, HMF, and acetic acid from a synthetic hydrolyzate containing 20 wt.% H(2)SO(4). Adsorption isotherms were determined experimentally. Loading and regeneration were investigated in a laboratory scale column. GAC has the highest adsorption capacity, but regeneration with water was not feasible. XAD-16 and CS16GC had lower adsorption capacities but also shorter cycle times due to easier regeneration. Productivity increased when regenerating with 50 wt.% EtOH(aq) solution. To compare adsorbents, process performance was quantified by productivity and fraction of inhibitors removed. GAC yields highest performance when high purity is required and ethanol can be used in regeneration. For lower purities, XAD-16 and GAC yield approximately equal performance. When using ethanol must be avoided, CS16GC offers highest productivity. Copyright © 2011 Elsevier Ltd. All rights reserved.

Catalytic cracking of non-edible sunflower oil over ZSM-5 for hydrocarbon bio-jet fuel.

PubMed

Zhao, Xianhui; Wei, Lin; Julson, James; Qiao, Qiquan; Dubey, Ashish; Anderson, Gary

2015-03-25

Non-edible sunflower oils that were extracted from sunflower residual wastes were catalytically cracked over a ZSM-5 catalyst in a fixed-bed reactor at three different reaction temperatures: 450°C, 500°C and 550°C. The catalyst was characterized using XRD, FT-IR, BET and SEM. Characterizations of the upgraded sunflower oils, hydrocarbon fuels, distillation residues and non-condensable gases were carried out. The effect of the reaction temperature on the yield and quality of liquid products was discussed. The results showed that the reaction temperature affected the hydrocarbon fuel yield but had a minor influence on its properties. The highest conversion efficiency from sunflower oils to hydrocarbon fuels was 30.1%, which was obtained at 550°C. The reaction temperature affected the component content of the non-condensable gases. The non-condensable gases generated at 550°C contained the highest content of light hydrocarbons (C1-C5), CO, CO2 and H2. Compared to raw sunflower oils, the properties of hydrocarbon fuels including the dynamic viscosity, pH, moisture content, density, oxygen content and heating value were improved. Copyright © 2015 Elsevier B.V. All rights reserved.

Calculation of total free energy yield as an alternative approach for predicting the importance of potential chemolithotrophic reactions in geothermal springs.

PubMed

Dodsworth, Jeremy A; McDonald, Austin I; Hedlund, Brian P

2012-08-01

To inform hypotheses regarding the relative importance of chemolithotrophic metabolisms in geothermal environments, we calculated free energy yields of 26 chemical reactions potentially supporting chemolithotrophy in two US Great Basin hot springs, taking into account the effects of changing reactant and product activities on the Gibbs free energy as each reaction progressed. Results ranged from 1.2 × 10(-5) to 3.6 J kg(-1) spring water, or 3.7 × 10(-5) to 11.5 J s(-1) based on measured flow rates, with aerobic oxidation of CH(4) or NH4 + giving the highest average yields. Energy yields calculated without constraining pH were similar to those at constant pH except for reactions where H(+) was consumed, which often had significantly lower yields when pH was unconstrained. In contrast to the commonly used normalization of reaction chemical affinities per mole of electrons transferred, reaction energy yields for a given oxidant varied by several orders of magnitude and were more sensitive to differences in the activities of products and reactants. The high energy yield of aerobic ammonia oxidation is consistent with previous observations of significant ammonia oxidation rates and abundant ammonia-oxidizing archaea in sediments of these springs. This approach offers an additional lens through which to view the thermodynamic landscape of geothermal springs. © 2012 Federation of European Microbiological Societies. Published by Blackwell Publishing Ltd. All rights reserved.

Study on the influence of various factors in the hydrometallurgical processing of waste printed circuit boards for copper and gold recovery.

PubMed

Birloaga, Ionela; De Michelis, Ida; Ferella, Francesco; Buzatu, Mihai; Vegliò, Francesco

2013-04-01

The present lab-scale experimental study presents the process of leaching waste printed circuit boards (WPCBs) in order to recover gold by thioureation. Preliminary tests have shown that copper adversely affects gold extraction; therefore an oxidative leaching pre-treatment was performed in order to remove base metals. The effects of sulfuric acid concentration, hydrogen peroxide volume and temperature on the metal extraction yield were studied by analysis of variance (ANOVA). The highest copper extraction yields were 76.12% for sample A and 18.29% for sample D, after leaching with 2M H2SO4, 20 ml of 30% H2O2 at 30°C for 3h. In order to improve Cu removal, a second leaching was performed only on sample A, resulting in a Cu extraction yield of 90%. Other experiments have shown the negative effect of the stirring rate on copper dissolution. The conditions used for the process of gold extraction by thiourea were: 20 g/L thiourea, 6g/L ferric ion, 10 g/L sulfuric acid, 600 rpm stirring rate. To study the influence of temperature and particle size, this process was tested on pins manually removed from computer central processing units (CPUs) and on waste CPU for 3½ h. A gold extraction yield of 69% was obtained after 75% of Cu was removed by a double oxidative leaching treatment of WPCBs with particle sizes smaller than 2 mm. Copyright © 2013 Elsevier Ltd. All rights reserved.

Exploring the effects of cell seeding density on the differentiation of human pluripotent stem cells to brain microvascular endothelial cells.

PubMed

Wilson, Hannah K; Canfield, Scott G; Hjortness, Michael K; Palecek, Sean P; Shusta, Eric V

2015-05-21

Brain microvascular-like endothelial cells (BMECs) derived from human pluripotent stem cells (hPSCs) have significant promise as tools for drug screening and studying the structure and function of the BBB in health and disease. The density of hPSCs is a key factor in regulating cell fate and yield during differentiation. Prior reports of hPSC differentiation to BMECs have seeded hPSCs in aggregates, leading to non-uniform cell densities that may result in differentiation heterogeneity. Here we report a singularized-cell seeding approach compatible with hPSC-derived BMEC differentiation protocols and evaluate the effects of initial hPSC seeding density on the subsequent differentiation, yield, and blood-brain barrier (BBB) phenotype. A range of densities of hPSCs was seeded and differentiated, with the resultant endothelial cell yield quantified via VE-cadherin flow cytometry. Barrier phenotype of purified hPSC-derived BMECs was measured via transendothelial electrical resistance (TEER), and purification protocols were subsequently optimized to maximize TEER. Expression of characteristic vascular markers, tight junction proteins, and transporters was confirmed by immunocytochemistry and quantified by flow cytometry. P-glycoprotein and MRP-family transporter activity was assessed by intracellular accumulation assay. The initial hPSC seeding density of approximately 30,000 cells/cm(2) served to maximize the yield of VE-cadherin+ BMECs per input hPSC. BMECs displayed the highest TEER (>2,000 Ω × cm(2)) within this same range of initial seeding densities, although optimization of the BMEC purification method could minimize the seeding density dependence for some lines. Localization and expression levels of tight junction proteins as well as efflux transporter activity were largely independent of hPSC seeding density. Finally, the utility of the singularized-cell seeding approach was demonstrated by scaling the differentiation and purification process down from 6-well to 96-well culture without impacting BBB phenotype. Given the yield and barrier dependence on initial seeding density, the singularized-cell seeding approach reported here should enhance the reproducibility and scalability of hPSC-derived BBB models, particularly for the application to new pluripotent stem cell lines.

Natural red dyes extraction on roselle petals

NASA Astrophysics Data System (ADS)

Inggrid, H. M.; Jaka; Santoso, H.

2016-11-01

Roselle (Hibiscus sabdariffa L.) has a high quantity of anthocyanin pigment and is a good colorant. The anthocyanin pigment can be used as a natural colorant and antioxidant. An antioxidant is an organic compound that has the ability to inhibit free radical reactions in the human body. The objective of this research is to study the effect of pH and temperature on total anthocyanin and antioxidant activity in roselle extract, and to evaluate the effect of temperature and sunlight on the stability of the red color from roselle. Dried roselle petals were extracted with solid liquid extraction method using water as solvent. The variables in this study are temperature (5°C, 30°C, and 55°C) and pH (2, 7, and 12). Total anthocyanin was analysed using the pH differential method. The antioxidant activities were determined using the DPPH method. The highest total anthocyanin in the roselle petals was 80.4 mg/L at a temperature of 5°C and pH 2. The highest antioxidant activity and yield content in the roselle were 90.4% and 71.6 % respectively, obtained at 55°C and pH 2.

Enhanced coproduction of hydrogen and methane from cornstalks by a three-stage anaerobic fermentation process integrated with alkaline hydrolysis.

PubMed

Cheng, Xi-Yu; Liu, Chun-Zhao

2012-01-01

A three-stage anaerobic fermentation process including H(2) fermentation I, H(2) fermentation II, methane fermentation was developed for the coproduction of hydrogen and methane from cornstalks. Hydrogen production from cornstalks using direct microbial conversion by Clostridium thermocellum 7072 was markedly enhanced in the two-stage thermophilic hydrogen fermentation process integrated with alkaline treatment. The highest total hydrogen yield from cornstalks in the two-stage fermentation process reached 74.4 mL/g-cornstalk. The hydrogen fermentation effluents and alkaline hydrolyzate were further used for methane fermentation by anaerobic granular sludge, and the total methane yield reached 205.8 mL/g-cornstalk. The total energy recovery in the three-stage anaerobic fermentation process integrated with alkaline hydrolysis reached 70.0%. Copyright © 2011 Elsevier Ltd. All rights reserved.

Recovery of yttrium from fluorescent powder of cathode ray tube, CRT: Zn removal by sulphide precipitation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Innocenzi, Valentina, E-mail: valentina.innocenzi1@univaq.it; De Michelis, Ida; Ferella, Francesco

2013-11-15

Highlights: • Treatment of fluorescent powder of CRT waste. • Factorial experimental designs to study acid leaching of fluorescent powder and the purification of leach liquors. • Recover of yttrium by precipitation using oxalic acid. • Suitable flowsheet to recover yttrium from fluorescent powder. - Abstract: This work is focused on the recovery of yttrium and zinc from fluorescent powder of cathode ray tube (CRT). Metals are extracted by sulphuric acid in the presence of hydrogen peroxide. Leaching tests are carried out according to a 2{sup 2} full factorial plan and the highest extraction yields for yttrium and zinc equalmore » to 100% are observed under the following conditions: 3 M of sulphuric acid, 10% v/v of H{sub 2}O{sub 2} concentrated solution at 30% v/v, 10% w/w pulp density, 70 °C and 3 h of reaction. Two series of precipitation tests for zinc are carried out: a 2{sup 2} full factorial design and a completely randomized factorial design. In these series the factors investigated are pH of solution during the precipitation and the amount of sodium sulphide added to precipitate zinc sulphide. The data of these tests are used to describe two empirical mathematical models for zinc and yttrium precipitation yields by regression analysis. The highest precipitation yields for zinc are obtained under the following conditions: pH equal to 2–2.5% and 10–12% v/v of Na{sub 2}S concentrated solution at 10% w/v. In these conditions the coprecipitation of yttrium is of 15–20%. Finally further yttrium precipitation experiments by oxalic acid on the residual solutions, after removing of zinc, show that yttrium could be recovered and calcined to obtain the final product as yttrium oxide. The achieved results allow to propose a CRT recycling process based on leaching of fluorescent powder from cathode ray tube and recovery of yttrium oxide after removing of zinc by precipitation. The final recovery of yttrium is 75–80%.« less

Higher biomolecules yield in phytoplankton under copper exposure.

PubMed

Silva, Jaqueline Carmo; Echeveste, Pedro; Lombardi, Ana Teresa

2018-05-30

Copper is an important metal for industry, and its toxic threshold in natural ecosystems has increased since the industrial revolution. As an essential nutrient, it is required in minute amounts, being toxic in slightly increased concentrations, causing great biochemical transformation in microalgae. This study aimed at investigating the physiology of Scenedesmus quadricauda, a cosmopolitan species, exposed to copper concentrations including those that trigger intracellular biochemical modifications. The Cu exposure concentrations tested ranged from 0.1 to 25 µM, thus including environmentally important levels. Microalgae cultures were kept under controlled environmental conditions and monitored daily for cell density, in vivo chlorophyll a, and photosynthetic quantum yield (Φ M ). After 24 h growth, free Cu 2+ ions were determined, and after 96 h, cellular Cu concentration, total carbohydrates, proteins, lipids, and cell volume were determined. The results showed that both free Cu 2+ ions and cellular Cu increased with Cu increase in culture medium. Microalgae cell abundance and in vivo chlorophyll a were mostly affected at 2.5 µM Cu exposure (3.8 pg Cu cell -1 ) and above. Approximately 31% decrease of photosynthetic quantum yield was obtained at the highest Cu exposure concentration (25 µM; 25 pg Cu cell -1 ) in comparison with the control. However, at environmentally relevant copper concentrations (0.5 µM Cu; 0.4 pg Cu cell -1 ) cell volume increased in comparison with the control. Considering biomolecules accumulation per unit cell volume, the highest carbohydrates and proteins yield was obtained at 1.0 µM Cu (1.1 pg Cu cell -1 ), while for lipids higher Cu was necessary (2.5 µM Cu; 3.8 pg Cu cell -1 ). This study is a contribution to the understanding of the effects of environmentally significant copper concentrations in the physiology of S. quadricauda, as well as to biotechnological approach to increase biomolecule yield in microalgae production. Copyright © 2018 Elsevier Inc. All rights reserved.

Supercritical Extraction of Scopoletin from Helichrysum italicum (Roth) G. Don Flowers.

PubMed

Jokić, Stela; Rajić, Marina; Bilić, Blanka; Molnar, Maja

2016-09-01

The increasing popularity of immortelle (Helichrysum italicum (Roth) G. Don) and its products, particularly in the cosmetic industry, is evident nowadays. This plant is a source of coumarins, especially scopoletin, which are highly soluble in supercritical CO2 . The objective of this study was to perform the supercritical CO2 extraction process of Helichrysum italicum flowers at different values of pressure and temperature and to optimise the extraction process using response surface methodology in terms of obtaining the highest extraction yield and yield of extracted scopoletin. Extraction was performed in a supercritical extraction system under different extraction conditions of pressure and temperature determined by central composite rotatable design. The mass of flowers in the extractor of 40 g, extraction time of 90 min and CO2 mass flow rate of 1.94 kg/h were kept constant during experiments. Antioxidant activity was determined using the DPPH (1,1-diphenyl-2-picrylhydrazyl) free radical scavenging assay method. Scopoletin concentration was determined by HPLC. Changes in extraction conditions affect the extracting results remarkably. The greatest extraction yield (6.31%) and the highest yield of scopoletin (1.933 mg/100 g) were obtained under extraction conditions of 20 MPa and 40°C. Extracts have also proven to possess antioxidant activity (44.0-58.1% DPPH scavenging activity) influenced by both temperature and pressure applied within the investigated parameters. The extraction conditions, especially pressure, exhibited significant influence on the extraction yield as well as the yield of extracted scopoletin and antioxidant activity of extracts. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Isolation and identification of a novel Candida sp. H2 producing D-arabitol and optimization of D-arabitol production.

PubMed

Song, Weibin; Lin, Yanqing; Hu, Haiyan; Xie, Zhipeng; Zhang, Jianguo

2011-03-01

To isolate a new osmophilic yeast for producing D-arabitol and research its optimal fermentation conditions for highest yield of D-arabitol from glucose. The isolated strain was characterized by electron microscopy, Biolog (GN) test, G + C content measurement and 26S rDNA D1/D2 domain sequences analysis. The purified fermentation product was identified by IR, 1H-NMR, 13C-NMR, MS and optical rotation analysis. Then the fermentation conditions for D-arabitol production were optimized. A new osmophilic yeast was isolated and identified as Candida sp. H2. Through the single factor experiment,the optimum conditions of 250 g/L glucose,10 g/L yeast extract, initial pH 6.0, 35 degrees C of culture temperature, 200 r/min of agitation, 200 mL medium in a 1000 mL flask of broth content, 1% (v/v) of inoculum size, 96 h of fermentation time were achieved. Based on the conditions above,weight yield of 35% (86.55 g D-arabitol from 250 g glucose) was obtained and 10% higher than the conditions not optimized. Candida sp. H2 was a novel strain for producing D-arabitol and valuable for further study.

Effect of the temperature, pH and irradiance on the photosynthetic activity by Scenedesmus obtusiusculus under nitrogen replete and deplete conditions.

PubMed

Cabello, Juan; Toledo-Cervantes, Alma; Sánchez, León; Revah, Sergio; Morales, Marcia

2015-04-01

This paper evaluates the effect of the irradiance, pH and temperature on the photosynthetic activity (PA) of Scenedesmus obtusiusculus under N-replete and N-deplete conditions through oxygen measurements. The highest PA values were 160 mgO2 gb(-1) h(-1) at 620 μmol m(-2) s(-1), 35 °C and pH of 8 under N-replete conditions and 3.3 mgO2 gb(-1) h(-1) at 100 μmol m(-2) s(-1), 28.5 °C and pH of 5.5 for N-deplete conditions. Those operation conditions were tested in a flat-panel photobioreactor. The biomass productivity was 0.97 gb L(-1) d(-1) under N-replete conditions with a photosynthetic efficiency (PE) of 4.4% yielding 0.85 gb mol photon(-1). Similar biomass productivity was obtained under N-deplete condition; and the lipid productivity was 0.34 gL L(-1) d(-1) with a PE of 7.8% yielding 0.39 gL mol photon(-1). The apparent activation and deactivation energies were 16.1 and 30 kcal mol(-1), and 11.9 and 15.3 kcal mol(-1), for N-replete and N-deplete conditions, respectively. Copyright © 2015 Elsevier Ltd. All rights reserved.

Optimization of growth and bacteriocin production by Lactobacillus sakei subsp. sakei2a.

PubMed

Malheiros, Patrícia S; Sant'Anna, Voltaire; Todorov, Svetoslav D; Franco, Bernadette D G M

2015-01-01

Lactobacillus sakei subsp. sakei 2a is a bacteriocinogenic lactic acid bacterium isolated from Brazilian pork sausage, capable of inhibiting the growth of microbial pathogens, mainly Listeria monocytogenes. In order to optimize bacteriocin production for industrial applications, this study evaluated the effect of supplementation of MRS broth with glucose, Tween 20, Tween 80, sodium citrate, potassium chloride and cysteine, and effect of the initial pH and temperature of incubation of the medium on production of bacteriocins by L. sakei 2a. Adding glucose and Tween 20 to the medium, an initial pH of 5.0 or 5.5, and incubation temperatures of 25 °C or 30 °C resulted to the highest bacteriocin yields. Thus, a 2(4) factorial design with the four variables was performed, and statistical analysis showed that it was an adequate model (R (2) = 0.8296). In the studied range, the four parameters significantly influenced bacteriocin production, with the maximum yield produced at an initial pH between 5.5 and 7.0, a temperature between 25 and 30 °C and supplementation of the MRS broth with glucose from 3.25 to 6.0 g L(-1) and Tween 20 from 0.575 to 1.15% (v/v). Response Surface Methodology analysis indicated that the highest bacteriocin production (12800 AU mL(-1)) occurred in the MRS broth supplemented with 5.5 g L(-1) glucose and 1.05% Tween 20 at an initial pH of 6.28 and an incubation temperature of 25 °C. The amount of bacteriocin produced in commercial MRS broths under the same conditions was only 5600AU mL(-1).

Mild chemical pretreatments are sufficient for complete saccharification of steam-exploded residues and high ethanol production in desirable wheat accessions.

PubMed

Zahoor; Tu, Yuanyuan; Wang, Lingqiang; Xia, Tao; Sun, Dan; Zhou, Shiguang; Wang, Yanting; Li, Ying; Zhang, Heping; Zhang, Tong; Madadi, Meysam; Peng, Liangcai

2017-11-01

In this study, a combined pretreatment was performed in four wheat accessions using steam explosion followed with different concentrations of H 2 SO 4 or NaOH, leading to increased hexoses yields by 3-6 folds from enzymatic hydrolysis. Further co-supplied with 1% Tween-80, Talq90 and Talq16 accessions exhibited an almost complete enzymatic saccharification of steam-exploded (SE) residues after 0.5% H 2 SO 4 or 1% NaOH pretreatment, with the highest bioethanol yields at 18.5%-19.4%, compared with previous reports about wheat bioethanol yields at 11%-17% obtained under relatively strong pretreatment conditions. Furthermore, chemical analysis indicated that much enhanced saccharification in Talq90 and Talq16 may be partially due to their relatively low cellulose CrI and DP values and high hemicellulose Ara and H-monomer levels in raw materials and SE residues. Hence, this study has not only demonstrated a mild pretreatment technology for a complete saccharification, but it has also obtained the high ethanol production in desirable wheat accessions. Copyright © 2017 Elsevier Ltd. All rights reserved.

Analysis of Biomethanation Process from market waste to generate bio energy

NASA Astrophysics Data System (ADS)

Sathish, S.; Parthiban, A.; Vinod kumar, T.; Chandrasekaran, M.

2017-03-01

In this study was to incur that the biogas production from traditional market wastes which were represented by cabbage stem and carrot peeling, white mustard were under taken in a laboratory experiment. To produce biogas, the raw material such as cabbage stem and carrot peeling, white mustard and carrot peeling were mixed until C/N ratio close 30:1. Inoculums starter cow dung is put into digester then water is added until 500 liters. The initial pH is measured at throughout the experiments. The anaerobic digestion process is conducted at temperature of 30ºC and the volumes, pH of the biogas yield were observed daily. Biogas yield and cumulative biogas, total solids were analyzed 35 days. The cumulative biogas yield at the 32th day of digestion for cabbage stem and carrot peeling (exp1), white mustard and carrot peeling (exp2) were 2140 liters and 2421 liters respectively. The highest daily biogas yield is achieved on the 22st day of digestion which is found 123 liters and 141 liters respectively. In the first 10 days, the pH level is observed decrease and increase after the day of 21. Although at the end of digestion period the pH will fall down.

A scanning probe investigation of the role of surface motifs in the behavior of p-WSe 2 photocathodes

DOE PAGES

Velazquez, Jesus M.; John, Jimmy; Esposito, Daniel V.; ...

2015-10-08

The spatial variation in the photoelectrochemical performance for the reduction of an aqueous one-electron redox couple, Ru(NH 3) 6 3+/2+, and for the evolution of H 2(g) from 0.5 M H 2SO 4(aq) at the surface of bare or Pt-decorated p-type WSe 2 photocathodes has been investigated in situ using scanning photocurrent microscopy (SPCM). The measurements revealed significant differences in the charge-collection performance (quantified by the values of external quantum yields, Φ ext) on various macroscopic terraces. Local spectral response measurements indicated a variation in the local electronic structure among the terraces, which was consistent with a non-uniform spatial distributionmore » of sub-band-gap states within the crystals. The photoconversion efficiencies of Pt-decorated p-WSe2 photocathodes were greater for the evolution of H 2(g) from 0.5 M H 2SO 4 than for the reduction of Ru(NH 3) 6 3+/2+, and terraces that exhibited relatively low values of Φext for the reduction of Ru(NH 3) 6 3+/2+ could in some cases yield values of Φ ext for the evolution of H 2(g) comparable to the values of Φ ext yielded by the highest-performing terraces. In conclusion, although the spatial resolution of the techniques used in this work frequently did not result in observation of the effect of edge sites on photocurrent efficiency, some edge effects were observed in the measurements; however the observed edge effects differed among edges, and did not appear to determine the performance of the electrodes.« less

Facile high-yield synthesis of polyaniline nanosticks with intrinsic stability and electrical conductivity.

PubMed

Li, Xin-Gui; Li, Ang; Huang, Mei-Rong

2008-01-01

Chemical oxidative polymerization at 15 degrees C was used for the simple and productive synthesis of polyaniline (PAN) nanosticks. The effect of polymerization media on the yield, size, stability, and electrical conductivity of the PAN nanosticks was studied by changing the concentration and nature of the acid medium and oxidant and by introducing organic solvent. Molecular and supramolecular structure, size, and size distribution of the PAN nanosticks were characterized by UV/Vis and IR spectroscopy, X-ray diffraction, laser particle-size analysis, and transmission electron microscopy. Introduction of organic solvent is advantageous for enhancing the yield of PAN nanosticks but disadvantageous for formation of PAN nanosticks with small size and high conductivity. The concentration and nature of the acid medium have a major influence on the polymerization yield and conductivity of the nanosized PAN. The average diameter and length of PAN nanosticks produced with 2 M HNO(3) and 0.5 M H(2)SO(4) as acid media are about 40 and 300 nm, respectively. The PAN nanosticks obtained in an optimal medium (i.e., 2 M HNO(3)) exhibit the highest conductivity of 2.23 S cm(-1) and the highest yield of 80.7 %. A mechanism of formation of nanosticks instead of nanoparticles is proposed. Nanocomposite films of the PAN nanosticks with poly(vinyl alcohol) show a low percolation threshold of 0.2 wt %, at which the film retains almost the same transparency and strength as pure poly(vinyl alcohol) but 262 000 times the conductivity of pure poly(vinyl alcohol) film. The present synthesis of PAN nanosticks requires no external stabilizer and provides a facile and direct route for fabrication of PAN nanosticks with high yield, controllable size, intrinsic self-stability, strong redispersibility, high purity, and optimizable conductivity.

Phase transformations and equation of state of praseodymium metal to 103 GPa

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chesnut, Gary N.; Vohra, Yogesh K.

2000-08-01

Pressure-induced structural phase transformations in a trivalent rare-earth metal praseodymium (Pr) were studied at room temperature in a diamond anvil cell to 103 GPa by energy dispersive x-ray diffraction using a synchrotron source. Our x-ray diffraction studies document the following crystal structure sequence: dhcp{yields}fcc{yields}distorted fcc(hR24 type){yields}monoclinic(C2/m){yields}{alpha}-uranium with increasing pressure. We measure a 16.7% volume collapse at the transition to the {alpha}-uranium phase at 20 GPa. The high-pressure {alpha}-uranium phase in Pr was found to be stable to the highest pressure of 103 GPa, which corresponds to a volume compression V/V{sub 0}=0.407. (c) 2000 The American Physical Society.

Low pressure catalytic co-conversion of biogenic waste (rapeseed cake) and vegetable oil.

PubMed

Giannakopoulou, Kanellina; Lukas, Michael; Vasiliev, Aleksey; Brunner, Christoph; Schnitzer, Hans

2010-05-01

Zeolite catalysts of three types (H-ZSM-5, Fe-ZSM-5 and H-Beta) were tested in the catalytic co-conversion of rapeseed cake and safflower oil into bio-fuel. This low pressure process was carried out at the temperatures of 350 and 400 degrees Celsius. The yields and compositions of the product mixtures depended on the catalyst nature and the process temperatures. The produced organic phases consisted mainly of hydrocarbons, fatty acids and nitriles. This mixture possessed improved characteristics (e.g. heating value, water content, density, viscosity, pH) compared with the bio-oils, making possible its application as a bio-fuel. The most effective catalyst, providing the highest yield of organic liquid phase, was the highly acidic/wide-pore H-Beta zeolite. The products obtained on this catalyst demonstrated the highest degree of deoxygenation and the higher HHV (Higher Heating Value). The aqueous liquid phase contained water-soluble carboxylic acids, phenols and heterocyclic compounds. Copyright 2009 Elsevier Ltd. All rights reserved.

Preparation of Chiral Triacylglycerols, sn-POO and sn-OOP, via Lipase-mediated Acidolysis Reaction.

PubMed

Yamamoto, Yukihiro; Yoshida, Hiroki; Nagai, Toshiharu; Hara, Setsuko

2018-02-01

It is well known that lipases are useful tools for preparing various structured triacylglycerols (TAGs). However, the lipase-mediated preparation of chiral TAGs has never been reported. This study aimed to prepare chiral TAGs (viz., 1-palmitoyl-2,3-dioleoyl-sn-glycerol (sn-POO) or 1,2-dioleoyl-3-palmitoyl-sn-glycerol (sn-OOP)) via lipase mediated acidolysis, using triolein (TO) and palmitic acid (P) as substrates. Three commercially available lipases (viz., Lipozyme RM-IM ® , Lipozyme TL-IM ® , and Lipase OF ® ) were used. Lipozyme RM-IM ® resulted in an increase 1P-2O (sn-POO + sn-OOP + 1,3-dioleoyl-2-palmitoyl-sn-glycerol) content with reaction time, which plateaued at 2~24 h (max. yield 47.1% at 4 h). The highest sn-POO/sn-OOP ratio of ca. 9 was obtained at 0.25 h, and the rate got close to 1 with reaction time (sn-POO/sn-OOP = 1.3 at 24 h). Lipozyme TL-IM ® resulted in a lower 1P-2O synthesis rate than Lipozyme RM-IM ® , where its highest sn-POO/sn-OOP ratio of ca. 2 was obtained at 0.25 h and did not vary much further with reaction time. In the case of Lipase OF ® , its reaction rate for 1P-2O synthesis was lower than that of the other two lipases, and the highest sn-POO/sn-OOP ratio of ca. 1.4 was obtained at 0.5 h, reaching closer to 1 with a longer reaction time. Reaction solvents (viz., hexane, acetone, and benzene) also affected the 1P-2O preparation, where the highest 1P-2O content was obtained with the solvent-free system. Furthermore, the solvent-free system showed a higher reaction rate for 1P-2O synthesis than did the hexane system, with no effect on chiral specificity of the lipase for the TAG molecules. These results suggested that among three types of commercial lipase, Lipozyme RM-IM ® is the most useful for the preparation of chiral TAGs by acidolysis reaction.

Optimization of growth and bacteriocin production by Lactobacillus sakei subsp. sakei2a

PubMed Central

Malheiros, Patrícia S.; Sant’Anna, Voltaire; Todorov, Svetoslav D.; Franco, Bernadette D.G.M.

2015-01-01

Lactobacillus sakei subsp. sakei 2a is a bacteriocinogenic lactic acid bacterium isolated from Brazilian pork sausage, capable of inhibiting the growth of microbial pathogens, mainly Listeria monocytogenes. In order to optimize bacteriocin production for industrial applications, this study evaluated the effect of supplementation of MRS broth with glucose, Tween 20, Tween 80, sodium citrate, potassium chloride and cysteine, and effect of the initial pH and temperature of incubation of the medium on production of bacteriocins by L. sakei 2a. Adding glucose and Tween 20 to the medium, an initial pH of 5.0 or 5.5, and incubation temperatures of 25 °C or 30 °C resulted to the highest bacteriocin yields. Thus, a 24 factorial design with the four variables was performed, and statistical analysis showed that it was an adequate model (R 2 = 0.8296). In the studied range, the four parameters significantly influenced bacteriocin production, with the maximum yield produced at an initial pH between 5.5 and 7.0, a temperature between 25 and 30 °C and supplementation of the MRS broth with glucose from 3.25 to 6.0 g L−1 and Tween 20 from 0.575 to 1.15% (v/v). Response Surface Methodology analysis indicated that the highest bacteriocin production (12800 AU mL−1) occurred in the MRS broth supplemented with 5.5 g L−1 glucose and 1.05% Tween 20 at an initial pH of 6.28 and an incubation temperature of 25 °C. The amount of bacteriocin produced in commercial MRS broths under the same conditions was only 5600AU mL−1. PMID:26413066

Ultrasound-assisted production of biodiesel and ethanol from spent coffee grounds.

PubMed

Rocha, Maria Valderez Ponte; de Matos, Leonardo José Brandão Lima; Lima, Larissa Pinto de; Figueiredo, Pablo Marciano da Silva; Lucena, Izabelly Larissa; Fernandes, Fabiano André Narciso; Gonçalves, Luciana Rocha Barros

2014-09-01

This study evaluates the production of biodiesel and ethanol from spent coffee grounds (SCG). The extraction of oil from SCG, biodiesel production and ethanol production processes were studied. The liquid-to-solid ratio and temperature were evaluated in the ultrasound-assisted extraction of the oil from SCG. The highest yield (12%) was obtained using 4 mL g(-1) liquid-to-solid ratio at 60°C for 45 min. The process to produce biodiesel showed a yield of 97% into fatty acid methyl esters (FAME). The highest glucose yield (192 mg g SCG(-1)) was obtained by hydrolysis with 0.4 mol L(-1) sulfuric acid at 121°C for 15 min. The hydrolysate was used as fermentation medium for ethanol production by Saccharomyces cerevisiae obtaining 19.0 g L(-1) at 10h of process of ethanol with a yield of ethanol and productivity of 0.50 g g(-1) and 1.90 g L(-1)h(-1), respectively. Spent coffee grounds were considered a potential feedstock for biodiesel and ethanol production. Copyright © 2014 Elsevier Ltd. All rights reserved.

Synthesis, characterisation, electrical and optical properties of copper borate compounds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kipcak, Azmi Seyhun; Senberber, Fatma Tugce; Aydin Yuksel, Sureyya

2015-10-15

Highlights: • Cu(BO{sub 2}){sub 2} was synthesized at the form of with pdf number of “00-001-0472”. • Particle sizes were found between 162.72 and 56.44 nm and 195.76 and 75.73 nm at CuSNaH. • Reaction yields were 90.4 ± 0.84, 96.9 ± 0.78 and 78.9 ± 0.76% for CuST, CuSB and CuSNaH. • The resistivity of CuST, CuSB and CuSNaH are 1.10 × 10{sup 7}, 7.02 × 10{sup 6} and 8.62 × 10{sup 5} Ωm. • The optical energy gap was 3.76 eV. - Abstract: The hydrothermal synthesis of copper borate compounds [Cu(BO{sub 2}){sub 2}] was studied, and several parametersmore » were found to affect the synthesis. Raw materials, including CuSO{sub 4}·5H{sub 2}O, Na{sub 2}B{sub 4}O{sub 7}·5H{sub 2}O, Na{sub 2}B{sub 4}O{sub 7}·10H{sub 2}O, NaOH and H{sub 3}BO{sub 3}, were used. Reaction temperatures and reaction times between 40 °C and 100 °C and 15 and 240 min, respectively, were used. The as-synthesised copper borate was analysed using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR) and scanning electron microscopy (SEM). The yields of the reactions were also calculated. Single-phase, nanoparticulate copper borate compounds (Cu(BO{sub 2}){sub 2}) possessing high XRD crystal scores were obtained; the reactions used to obtain these materials were highly efficient. Electrical resistivity and optical absorbance measurements were carried out on the compounds obtained from the highest yielding reactions. The results of this study showed that even using a reaction time of 15 min, copper borate formation was successfully achieved.« less

Pyrolysis and gasification of landfilled plastic wastes with Ni-Mg-La/Al2O3 catalyst.

PubMed

Kaewpengkrow, Prangtip; Atong, Duangduen; Sricharoenchaikul, Viboon

2012-12-01

Pyrolysis and gasification processes were utilized to study the feasibility of producing fuels from landfilled plastic wastes. These wastes were converted in a gasifier at 700-900 degrees C. The equivalence ratio (ER) was varied from 0.4-0.6 with or without addition ofa Ni-Mg-La/Al2O3 catalyst. The pyrolysis and gasification of plastic wastes without catalyst resulted in relatively low H2, CO and other fuel gas products with methane as the major gaseous species. The highest lower heating value (LHV) was obtained at 800 degrees C and for an ER of 0.4, while the maximum cold gas efficiency occurred at 700 degrees C and for an ER of 0.4. The presence of the Ni-Mg-La/Al2O3 catalyst significantly enhanced H2 and CO production as well as increasing the gas energy content to 15.76-19.26 MJ/m3, which is suitable for further usage as quality fuel gas. A higher temperature resulted in more H2 and CO and other product gas yields, while char and liquid (tars) decreased. The maximum gas yield, gas calorific value and cold gas efficiency were achieved when the Ni-Mg-La/Al2O3 catalyst was used at 900 degrees C. In general, addition of prepared catalyst resulted in greater H2, CO and other light hydrocarbon yields from superior conversion of wastes to these gases. Thus, thermochemical treatment of these problematic wastes using pyrolysis and gasification processes is a very attractive alternative for sustainable waste management.

Two-stage conversion of crude glycerol to energy using dark fermentation linked with microbial fuel cell or microbial electrolysis cell.

PubMed

Chookaew, Teera; Prasertsan, Poonsuk; Ren, Zhiyong Jason

2014-03-25

Crude glycerol is a main byproduct of the biodiesel industry, and the beneficial use of waste glycerol has been a major challenge. This study characterises the conversion of crude glycerol into bioenergy such as H2 and electricity using a two-stage process linking dark fermentation with a microbial fuel cell (MFC) or microbial electrolysis cell (MEC). The results showed that fermentation achieved a maximum H2 rate of 332 mL/L and a yield of 0.55 mol H2/mol glycerol, accompanied by 20% of organic removal. Fed with the raw fermentation products with an initial COD of 7610 mg/L, a two-chamber MFC produced 92 mW/m(2) in power density and removed 50% of COD. The Columbic efficiency was 14%. When fed with 50% diluted fermentation product, a similar power output (90m W/m(2)) and COD removal (49%) were obtained, but the CE doubled to 27%. Similar substrates were used to produce H2 in two-chamber MECs, and the diluted influent had a higher performance, with the highest yield at 106 mL H2/g COD and a CE of 24%. These results demonstrate that dark fermentation linked with MFC/MEC can be a feasible option for conversion of waste glycerol into bioenergy. Copyright © 2013 Elsevier B.V. All rights reserved.

Enhancement of hydrolysis of Chlorella vulgaris by hydrochloric acid.

PubMed

Park, Charnho; Lee, Ja Hyun; Yang, Xiaoguang; Yoo, Hah Young; Lee, Ju Hun; Lee, Soo Kweon; Kim, Seung Wook

2016-06-01

Chlorella vulgaris is considered as one of the potential sources of biomass for bio-based products because it consists of large amounts of carbohydrates. In this study, hydrothermal acid hydrolysis with five different acids (hydrochloric acid, nitric acid, peracetic acid, phosphoric acid, and sulfuric acid) was carried out to produce fermentable sugars (glucose, galactose). The hydrothermal acid hydrolysis by hydrochloric acid showed the highest sugar production. C. vulgaris was hydrolyzed with various concentrations of hydrochloric acid [0.5-10 % (w/w)] and microalgal biomass [20-140 g/L (w/v)] at 121 °C for 20 min. Among the concentrations examined, 2 % hydrochloric acid with 100 g/L biomass yielded the highest conversion of carbohydrates (92.5 %) into reducing sugars. The hydrolysate thus produced from C. vulgaris was fermented using the yeast Brettanomyces custersii H1-603 and obtained bioethanol yield of 0.37 g/g of algal sugars.

Comparative Thermal Aging Effects on PM-HIP and Forged Inconel 690

NASA Astrophysics Data System (ADS)

Bullens, Alexander L.; Bautista, Esteban; Jaye, Elizabeth H.; Vas, Nathaniel L.; Cain, Nathan B.; Mao, Keyou; Gandy, David W.; Wharry, Janelle P.

2018-03-01

This study compares thermal aging effects in Inconel 690 (IN690) produced by forging and powder metallurgy with hot isostatic pressing (PM-HIP). Isothermal aging is carried out over 400-800°C for up to 1000 h and then metallography and nanoindentation are utilized to relate grain microstructure with hardness and yield strength. The PM-HIP IN690 maintains a constant grain size through all aging conditions, while the forged IN690 exhibits limited grain growth at the highest aging temperature and longest aging time. The PM-HIP IN690 exhibits comparable mechanical integrity as the forged material throughout aging: hardness and yield strength are unchanged with 100 h aging, but increase after 1000 h aging at all temperatures. In both the PM-HIP and forged IN690, the Hall-Petch relationship for Ni-based superalloys predicts yield strength for 0-100 h aged specimens, but underestimates yield strength in the 1000 h aged specimens because of thermally induced precipitation.

Corn Yield and Soil Nitrous Oxide Emission under Different Fertilizer and Soil Management: A Three-Year Field Experiment in Middle Tennessee.

PubMed

Deng, Qi; Hui, Dafeng; Wang, Junming; Iwuozo, Stephen; Yu, Chih-Li; Jima, Tigist; Smart, David; Reddy, Chandra; Dennis, Sam

2015-01-01

A three-year field experiment was conducted to examine the responses of corn yield and soil nitrous oxide (N2O) emission to various management practices in middle Tennessee. The management practices include no-tillage + regular applications of urea ammonium nitrate (NT-URAN); no-tillage + regular applications of URAN + denitrification inhibitor (NT-inhibitor); no-tillage + regular applications of URAN + biochar (NT-biochar); no-tillage + 20% applications of URAN + chicken litter (NT-litter), no-tillage + split applications of URAN (NT-split); and conventional tillage + regular applications of URAN as a control (CT-URAN). Fertilizer equivalent to 217 kg N ha(-1) was applied to each of the experimental plots. Results showed that no-tillage (NT-URAN) significantly increased corn yield by 28% over the conventional tillage (CT-URAN) due to soil water conservation. The management practices significantly altered soil N2O emission, with the highest in the CT-URAN (0.48 mg N2O m(-2) h(-1)) and the lowest in the NT-inhibitor (0.20 mg N2O m(-2) h(-1)) and NT-biochar (0.16 mg N2O m(-2) h(-1)) treatments. Significant exponential relationships between soil N2O emission and water filled pore space were revealed in all treatments. However, variations in soil N2O emission among the treatments were positively correlated with the moisture sensitivity of soil N2O emission that likely reflects an interactive effect between soil properties and WFPS. Our results indicated that improved fertilizer and soil management have the potential to maintain highly productive corn yield while reducing greenhouse gas emissions.

Corn Yield and Soil Nitrous Oxide Emission under Different Fertilizer and Soil Management: A Three-Year Field Experiment in Middle Tennessee

PubMed Central

Deng, Qi; Hui, Dafeng; Wang, Junming; Iwuozo, Stephen; Yu, Chih-Li; Jima, Tigist; Smart, David; Reddy, Chandra; Dennis, Sam

2015-01-01

Background A three-year field experiment was conducted to examine the responses of corn yield and soil nitrous oxide (N2O) emission to various management practices in middle Tennessee. Methodology/Principal Findings The management practices include no-tillage + regular applications of urea ammonium nitrate (NT-URAN); no-tillage + regular applications of URAN + denitrification inhibitor (NT-inhibitor); no-tillage + regular applications of URAN + biochar (NT-biochar); no-tillage + 20% applications of URAN + chicken litter (NT-litter), no-tillage + split applications of URAN (NT-split); and conventional tillage + regular applications of URAN as a control (CT-URAN). Fertilizer equivalent to 217 kg N ha-1 was applied to each of the experimental plots. Results showed that no-tillage (NT-URAN) significantly increased corn yield by 28% over the conventional tillage (CT-URAN) due to soil water conservation. The management practices significantly altered soil N2O emission, with the highest in the CT-URAN (0.48 mg N2O m-2 h-1) and the lowest in the NT-inhibitor (0.20 mg N2O m-2 h-1) and NT-biochar (0.16 mg N2O m-2 h-1) treatments. Significant exponential relationships between soil N2O emission and water filled pore space were revealed in all treatments. However, variations in soil N2O emission among the treatments were positively correlated with the moisture sensitivity of soil N2O emission that likely reflects an interactive effect between soil properties and WFPS. Conclusion/Significance Our results indicated that improved fertilizer and soil management have the potential to maintain highly productive corn yield while reducing greenhouse gas emissions. PMID:25923716

Bioconversion of D-galactose to D-tagatose: continuous packed bed reaction with an immobilized thermostable L-arabinose isomerase and efficient purification by selective microbial degradation.

PubMed

Liang, Min; Chen, Min; Liu, Xinying; Zhai, Yafei; Liu, Xian-wei; Zhang, Houcheng; Xiao, Min; Wang, Peng

2012-02-01

The continuous enzymatic conversion of D-galactose to D-tagatose with an immobilized thermostable L-arabinose isomerase in packed-bed reactor and a novel method for D-tagatose purification were studied. L-arabinose isomerase from Thermoanaerobacter mathranii (TMAI) was recombinantly overexpressed and immobilized in calcium alginate. The effects of pH and temperature on D-tagatose production reaction catalyzed by free and immobilized TMAI were investigated. The optimal condition for free enzyme was pH 8.0, 60°C, 5 mM MnCl(2). However, that for immobilized enzyme was pH 7.5, 75°C, 5 mM MnCl(2). In addition, the catalytic activity of immobilized enzyme at high temperature and low pH was significantly improved compared with free enzyme. The optimum reaction yield with immobilized TMAI increased by four percentage points to 43.9% compared with that of free TMAI. The highest productivity of 10 g/L h was achieved with the yield of 23.3%. Continuous production was performed at 70°C; after 168 h, the reaction yield was still above 30%. The resultant syrup was then incubated with Saccharomyces cerevisiae L1 cells. The selective degradation of D-galactose was achieved, obtaining D-tagatose with the purity above 95%. The established production and separation methods further potentiate the industrial production of D-tagatose via bioconversion and biopurification processes.

Characterization of a newly synthesized carbonyl reductase and construction of a biocatalytic process for the synthesis of ethyl (S)-4-chloro-3-hydroxybutanoate with high space-time yield.

PubMed

You, Zhong-Yu; Liu, Zhi-Qiang; Zheng, Yu-Guo

2014-02-01

A carbonyl reductase (SCR2) gene was synthesized and expressed in Escherichia coli after codon optimization to investigate its biochemical properties and application in biosynthesis of ethyl (S)-4-chloro-3-hydroxybutanoate ((S)-CHBE), which is an important chiral synthon for the side chain of cholesterol-lowering drug. The recombinant SCR2 was purified and characterized using ethyl 4-chloro-3-oxobutanoate (COBE) as substrate. The specific activity of purified enzyme was 11.9 U mg(-1). The optimum temperature and pH for enzyme activity were 45 °C and pH 6.0, respectively. The half-lives of recombinant SCR2 were 16.5, 7.7, 2.2, 0.41, and 0.05 h at 30 °C, 35 °C, 40 °C, 45 °C, and 50 °C, respectively, and it was highly stable in acidic environment. This SCR2 displayed a relatively narrow substrate specificity. The apparent K m and V max values of purified enzyme for COBE are 6.4 mM and 63.3 μmol min(-1) mg(-1), respectively. The biocatalytic process for the synthesis of (S)-CHBE was constructed by this SCR2 in an aqueous-organic solvent system with a substrate fed-batch strategy. At the final COBE concentration of 1 M, (S)-CHBE with yield of 95.3% and e.e. of 99% was obtained after 6-h reaction. In this process, the space-time yield per gram of biomass (dry cell weight, DCW) and turnover number of NADP(+) to (S)-CHBE were 26.5 mmol L(-1) h(-1) g(-1) DCW and 40,000 mol/mol, respectively, which were the highest values as compared with other works.

Efficient acetone-butanol-ethanol production by Clostridium beijerinckii from sugar beet pulp.

PubMed

Bellido, Carolina; Infante, Celia; Coca, Mónica; González-Benito, Gerardo; Lucas, Susana; García-Cubero, María Teresa

2015-08-01

Sugar beet pulp (SBP) has been investigated as a promising feedstock for ABE fermentation by Clostridium beijerinckii. Although lignin content in SBP is low, a pretreatment is needed to enhance enzymatic hydrolysis and fermentation yields. Autohydrolysis at pH 4 has been selected as the best pretreatment for SBP in terms of sugars release and acetone and butanol production. The best overall sugars release yields from raw SBP ranged from 66.2% to 70.6% for this pretreatment. The highest ABE yield achieved was 0.4g/g (5.1g/L of acetone and 6.6g/L butanol) and 143.2g ABE/kg SBP (62.3g acetone and 80.9g butanol) were obtained when pretreated SBP was enzymatically hydrolyzed at 7.5% (w/w) solid loading. Higher solid loadings (10%) offered higher acetone and butanol titers (5.8g/L of acetone and 7.8g/L butanol). All the experiments were carried out under not-controlling pH conditions reaching about 5.3 in the final samples. Copyright © 2015 Elsevier Ltd. All rights reserved.

Enantioconvergent hydrolysis of racemic styrene oxide at high concentration by a pair of novel epoxide hydrolases into (R)-phenyl-1,2-ethanediol.

PubMed

Wang, Rui; Hu, Die; Zong, Xuncheng; Li, Jinping; Ding, Lei; Wu, Minchen; Li, Jianfang

2017-12-01

To prepare (R)-phenyl-1,2-ethanediol ((R)-PED) with high enantiomeric excess (ee p ) and yield from racemic styrene oxide (rac-SO) at high concentration by bi-enzymatic catalysis. The bi-enzymatic catalysis was designed for enantioconvergent hydrolysis of rac-SO by a pair of novel epoxide hydrolases (EHs), a Vigna radiata EH3 (VrEH3) and a variant (AuEH2 A250I ) of Aspergillus usamii EH2. The simultaneous addition mode of VrEH3 and AuEH2 A250I , exhibiting the highest average turnover frequency (aTOF) of 0.12 g h -1 g -1 , was selected, by which rac-SO (10 mM) was converted into (R)-PED with 92.6% ee p and 96.3% yield. Under the optimized reaction conditions: dry weight ratio 14:1 of VrEH3-expressing E. coli/vreh3 to AuEH2 A250I -expressing E. coli/Aueh2 A250I and reaction at 20 °C, rac-SO (10 mM) was completely hydrolyzed in 2.3 h, affording (R)-PED with 98% ee p . At the weight ratio 0.8:1 of rac-SO to two mixed dry cells, (R)-PED with 97.4% ee p and 98.7% yield was produced from 200 mM (24 mg/ml) rac-SO in 10.5 h. Enantioconvergent hydrolysis of rac-SO at high concentration catalyzed by both VrEH3 and AuEH2 A250I is an effective method for preparing (R)-PED with high ee p and yield.

Experimental determination of positron-related surface characteristics of 6H-SiC

NASA Astrophysics Data System (ADS)

Nangia, A.; Kim, J. H.; Weiss, A. H.; Brauer, G.

2002-03-01

The positron work function of 6H-SiC was determined to be -2.1±0.1 eV from an analysis of the energy spectrum of positrons reemitted from the surface. The positron reemission yield, highest in the sample inserted into vacuum after atmospheric exposure and cleaning with ethanol, was significantly reduced after sputtering with 3 keV, 125 μA min Ne+ ions. The yield was not recovered even after annealing at 900 °C, presumably due to the stability of sputter induced defects. Sputtering at lower energies caused a smaller decrease in the reemission yield that was largely recovered after annealing at 850 °C. Analysis using electron induced Auger electron spectroscopy and positron-annihilation-induced Auger electron spectroscopy indicated that the surface was Si enriched after sputtering and C enriched after subsequent annealing. Values of positron diffusion length and mobility in the unsputtered material were extracted from the dependence of the reemission yield on the beam energy. The application of SiC as a field-assisted positron moderator is discussed.

Microwave assisted alkaline pretreatment to enhance enzymatic saccharification of catalpa sawdust.

PubMed

Jin, Shuguang; Zhang, Guangming; Zhang, Panyue; Li, Fan; Wang, Siqi; Fan, Shiyang; Zhou, Shuqiong

2016-12-01

Catalpa sawdust, a promising biofuel production biomass, was pretreated by microwave-water, -NaOH, and -Ca(OH) 2 to enhance enzymatic digestibility. After 48h enzymatic hydrolysis, microwave-Ca(OH) 2 pretreated sample showed the highest reducing sugar yield. The content of hemicellulose and lignin in catalpa sawdust decreased after microwave-alkali pretreatment. SEM observation showed that the catalpa sawdust surface with microwave-Ca(OH) 2 pretreatment suffered the most serious erosion. Crystallinity index of catalpa sawdust increased after all three kinds of pretreatment. The optimum conditions of microwave-Ca(OH) 2 pretreatment were particle size of 40mesh, Ca(OH) 2 dosage of 2.25% (w/v), microwave power of 400W, pretreatment time of 6min, enzyme loading of 175FPU/g, and hydrolysis time of 96h, and the reducing sugar yield of microwave-Ca(OH) 2 pretreated catalpa sawdust reached 402.73mg/g, which increased by 682.15% compared with that of raw catalpa sawdust. The catalpa sawdust with microwave-Ca(OH) 2 pretreatment is promising for biofuel production with great potential. Copyright © 2016 Elsevier Ltd. All rights reserved.

Fermentative hydrogen production from liquid swine manure with glucose supplement using an anaerobic sequencing batch reactor

NASA Astrophysics Data System (ADS)

Wu, Xiao

2009-12-01

The idea of coupling renewable energy production and agricultural waste management inspired this thesis. The production of an important future fuel---hydrogen gas---from high strength waste stream-liquid swine manure---using anaerobic treatment processes makes the most sustainable sense for both wastewater utilization and energy generation. The objectives of this thesis were to develop a fermentation process for converting liquid swine manure to hydrogen and to maximize hydrogen productivity. Anaerobic sequencing batch reactor (ASBR) systems were constructed to carry out this fermentation process, and seed sludge obtained from a dairy manure anaerobic digester and pretreated by nutrient acclimation, heat and pH treatment was used as inoculum. High system stability was indicated by a short startup period of 12 days followed by stable hydrogen production, and successful sludge granulation occurred within 23 days of startup at a hydraulic retention time (HRT) of 24 hours. Operation at a progressively decreasing HRT from 24 to 8h gave rise to an increasing biogas production rate from 15.2-34.4L/d, while good linear relationships were observed between both total biogas and hydrogen production rates correlated to HRT, with R2 values of 0.993 and 0.997, respectively. The maximum hydrogen yield of 1.63 mol-H 2/mol-hexose-feed occurred at HRT of 16h, while the HRT of 12h was highly suggested to achieve both high production rate and efficient yield. Hexose utilization efficiencies over 98%, considerable hydrogen production rate up to 14.3 L/d and hydrogen percentage of off-gas up to 43% (i.e., a CO 2/H2 ratio of 1.2) with the absence of CH4 production throughout the whole course of experiment at a pH of 5.0 strongly validated the feasibility of the fermentative H2 production from liquid swine manure using an ASBR system. Ethanol as well as acetic, butyric and valeric acids were produced in the system accompanying the hydrogen production, with acetic acid being the dominant one, which contributed to 56-58% of the total soluble metabolite production, indicative of an acetic acid fermentation system, and acetate-to-butyrate ratio was found to be closely related to hydrogen yield. pH level influenced every aspect of the ASBR performance for hydrogen production. ASBR operation at five pHs ranging from 4.4 to 5.6 (4.4, 4.7, 5.0, 5.3, 5.6) showed distinct dynamic profiles of both biogas production and the changes of H2 and CH4 percentage in the biogas during a running period of 22 days. The H2 content in biogas, H 2 production rate and H2 yield were all pH-dependent, in the range of 5.1-36.9 %, 0.71-8.97 L/d and 0.12-1.50 mol-H2/mol-glucose, respectively, and maximum values for all three responses were simultaneously achieved at pH 5.0. Methanogens appeared to be significantly activated at pH of 5.3 or higher since significant CH4 evolution and concurrent reduction in H2 production was observed at pH 5.3 and 5.6. Acetate, propionate, butyrate, valerate, and ethanol were main aqueous products in all pH tests and their distribution was influenced by pH. Analysis of kinetic models developed from modified Gompertz equations for batch experiments showed that pH had a profound effect on all kinetic parameters for hydrogen production including hydrogen potential, maximum hydrogen production rate and the length of the lag phase, as well as the maximum substrate utilization rate. The low pH of 4.4 gave the highest hydrogen production potential but with the lowest hydrogen production rate. A contrast experiment was conducted with an initial pH of 5.3 but not controlled, came up with a rapid pH decline, leading to a low hexose degradation efficiency of 33.2% and a significantly suppressed H2 production, indicating the importance of pH control and the effect of pH on H2 production and substrate consumption. pH 5.0 was verified as the optimal for the proposed fermentation system by kinetic models. An extremely linear relationship (R2= 0.993) between the maximum H2 production rate and the maximum hexose degradation rate suggested that the pH inhibition on H2 production was a result of the suppression on the bacterial activity for substrate utilization due to an unfavorable pH level. System optimization was realized through experiments conducted according to a response surface methodology, with a central composite design and empirical quadratic response equations obtained for three responses including the hydrogen content in the biogas, hydrogen evolution rate and hydrogen yield, against three independent variables, pH (4.4-5.6), HRT (8-24h) and substrate glucose concentrations (Cg, 0-20 g/L). Contour plots revealed that all three responses were significantly impacted by the variable and squared pH. Furthermore, pH and Cg had a significant interaction effect on H2 production rate, while HRT and glucose concentration were interdependent, or they had a mildly significant interaction effect on H2 production rate. The hydrogen content decreased when pH was greater than 5.0 or less than 4.6 and a largest value of 42.7% could be obtained at pH 4.8, HRT 8 h, and Cg of 18.7 g/L. The highest hydrogen production rate of 26.1 L/d happened under a pH of 4.6, HRT of 8h, and Cg of 20 g/L; Lower HRT and higher Cg was found to benefit the H2 production rate because they provide elevated organic loading and food to microorganism ratio for the system. HRT shorter than 17h resulted in declined hydrogen yield, while the glucose concentration up to 20 g/L did not cause suppression on hydrogen yield. The revised optimal condition of pH 4.8, HRT 11h, and Cg of 20 g/L, which could achieve 85% of the maximum values of all three hydrogen productivity responses, was determined by surface response methodology. Highly reproducible results from confirming experiments at the optimal condition indicated that the results modeled in this study possessed a high reliability, while the results of H2 content, H2 production rate and yield were obtained as 40.3%, 23.16 L/d, and 1.36mol H2/mol hexose, respectively. Results obtained in this study indicated that ASBR system using swine manure based substrate had significant potential of fermentative hydrogen production. Key words: biohydrogen production, hydrogen fermentation, liquid swine manure, anaerobic sequencing batch reactor (ASBR), hydrogen content, hydrogen production rate, hydrogen yield

Identifying yield-optimizing environments for two cowpea breeding lines by manipulating photoperiod and harvest scenario

NASA Technical Reports Server (NTRS)

Ohler, T. A.; Mitchell, C. A.

1996-01-01

Photoperiod and harvest scenario of cowpea (Vigna unguiculata L. Walp) canopies were manipulated to optimize productivity for use in future controlled ecological life-support systems. Productivity was measured by edible yield rate (EYR:g m-2 day-1), shoot harvest index (SHI: g edible biomass [g total shoot dry weight]), and yield-efficiency rate (YER:g edible biomass m-2 day-1 per[g nonedible shoot dry weight]). Breeding lines 'IT84S-2246' (S-2246) and "IT82D-889' (D-889) were grown in a greenhouse under 8-, 12-, or 24-h photoperiods. S-2246 was short-day and D-889 was day-neutral for flowering. Under each photoperiod, cowpeas were harvested either for leaves only, seeds only, or leaves plus seeds (mixed harvest). Photoperiod did not affect EYR of either breeding line for any harvest scenario tested. Averaged over both breeding lines, seed harvest gave the highest EYR at 6.7 g m-2 day-1. The highest SHI (65%) and YER (94 mg m-2 day-1 g-1) were achieved for leaf-only harvest of D-889 under an 8-h photoperiod. For leaf-only harvest of S-2246, both SHI and YER increased with increasing photoperiod, but declined for seed-only and mixed harvests. However, photoperiod had no effect on SHI or YER for D-889 for any harvest scenario. A second experiment utilized the short-day cowpea breeding line 'IT89KD-288' (D-288) and the day-neutral breeding line 'IT87D-941-1' (D-941) to compare yield parameters using photoperiod extension under differing lamp types. This experiment confirmed the photoperiod responses of D-889 and S-2246 to a mixed-harvest scenario and indicated that daylength extension with higher irradiance from high pressure sodium lamps further suppressed EYR, SHI, and YER of the short-day breeding line D-288.

Large-moment antiferromagnetic order in overdoped high-Tc superconductor 154SmFeAsO1-xDx

NASA Astrophysics Data System (ADS)

Iimura, Soshi; Okanishi, Hiroshi; Matsuishi, Satoru; Hiraka, Haruhiro; Honda, Takashi; Ikeda, Kazutaka; Hansen, Thomas C.; Otomo, Toshiya; Hosono, Hideo

2017-05-01

In iron-based superconductors, high critical temperature (Tc) superconductivity over 50 K has only been accomplished in electron-doped hREFeAsO (hRE is heavy rare earth (RE) element). Although hREFeAsO has the highest bulk Tc (58 K), progress in understanding its physical properties has been relatively slow due to difficulties in achieving high-concentration electron doping and carrying out neutron experiments. Here, we present a systematic neutron powder diffraction study of 154SmFeAsO1-xDx, and the discovery of a long-range antiferromagnetic ordering with x ≥ 0.56 (AFM2) accompanying a structural transition from tetragonal to orthorhombic. Surprisingly, the Fe magnetic moment in AFM2 reaches a magnitude of 2.73 μB/Fe, which is the largest in all nondoped iron pnictides and chalcogenides. Theoretical calculations suggest that the AFM2 phase originates in kinetic frustration of the Fe-3dxy orbital, in which the nearest-neighbor hopping parameter becomes zero. The unique phase diagram, i.e., highest-Tc superconducting phase adjacent to the strongly correlated phase in electron-overdoped regime, yields important clues to the unconventional origins of superconductivity.

Benzofuranyl Esters: Synthesis, Crystal Structure Determination, Antimicrobial and Antioxidant Activities.

PubMed

Kumar, C S Chidan; Then, Li Yee; Chia, Tze Shyang; Chandraju, Siddegowda; Win, Yip-Foo; Sulaiman, Shaida Fariza; Hashim, Nurul Shafiqah; Ooi, Kheng Leong; Quah, Ching Kheng; Fun, Hoong-Kun

2015-09-11

A series of five new 2-(1-benzofuran-2-yl)-2-oxoethyl 4-(un/substituted)benzoates 4(a-e), with the general formula of C₈H₅O(C=O)CH₂O(C=O)C₆H₄X, X = H, Cl, CH₃, OCH₃ or NO₂, was synthesized in high purity and good yield under mild conditions. The synthesized products 4(a-e) were characterized by FTIR, ¹H-, (13)C- and ¹H-(13)C HMQC NMR spectroscopic analysis and their 3D structures were confirmed by single-crystal X-ray diffraction studies. These compounds were screened for their antimicrobial and antioxidant activities. The tested compounds showed antimicrobial ability in the order of 4b < 4a < 4c < 4d < 4e and the highest potency with minimum inhibition concentration (MIC) value of 125 µg/mL was observed for 4e. The results of antioxidant activities revealed the highest activity for compound 4e (32.62% ± 1.34%) in diphenyl-2-picrylhydrazyl (DPPH) radical scavenging, 4d (31.01% ± 4.35%) in ferric reducing antioxidant power (FRAP) assay and 4a (27.11% ± 1.06%) in metal chelating (MC) activity.

Efficient mannitol production by wild-type Lactobacillus reuteri CRL 1101 is attained at constant pH using a simplified culture medium.

PubMed

Ortiz, Maria Eugenia; Raya, Raúl R; Mozzi, Fernanda

2015-10-01

Mannitol is a natural polyol with multiple industrial applications. In this work, mannitol production by Lactobacillus reuteri CRL 1101 was studied at free- and controlled-pH (6.0-4.8) fermentations using a simplified culture medium containing yeast and beef extracts and sugarcane molasses. The activity of mannitol 2-dehydrogenase (MDH), the enzyme responsible for mannitol synthesis, was determined. The effect of the initial biomass concentration was further studied. Mannitol production (41.5 ± 1.1 g/l), volumetric productivity (Q Mtl 1.73 ± 0.05 g/l h), and yield (Y Mtl 105 ± 11 %) were maximum at pH 5.0 after 24 h while the highest MDH activity (1.66 ± 0.09 U/mg protein) was obtained at pH 6.0. No correlation between mannitol production and MDH activity was observed when varying the culture pH. The increase (up to 2000-fold) in the initial biomass concentration did not improve mannitol formation after 24 h although a 2-fold higher amount was produced at 8 h using 1 or 2 g cell dry weight/l comparing to the control (0.001 g cell dry weight/l). Finally, mannitol isolation under optimum fermentation conditions was achieved. The mannitol production obtained in this study is the highest reported so far by a wild-type L. reuteri strain and, more interestingly, using a simplified culture medium.

Synthesis of renewable high-density fuel with isophorone.

PubMed

Wang, Wei; Liu, Yanting; Li, Ning; Li, Guangyi; Wang, Wentao; Wang, Aiqin; Wang, Xiaodong; Zhang, Tao

2017-07-21

1,1,3-Trimethyl-5-(2,4,4-trimethylcyclohexyl)cyclohexane, a renewable high density fuel, was first produced in a high overall carbon yield (~70%) with isophorone which can be derived from hemicellulose. The synthetic route used this work contains three steps. In the first step, 3,3,5-trimethylcyclohexanone was synthesized by the selective hydrogenation of isophorone. Among the investigated catalysts, the Pd/C exhibited the highest activity and selectivity. Over this catalyst, a high carbon yield (99.0%) of 3,3,5-trimethylcyclohexanone was achieved under mild conditions (298 K, 2 MPa H 2 , 1 h). In the second step, 3,5,5-trimethyl-2-(3,3,5-trimethylcyclohexylidene)cyclohexanone was produced in a high carbon yield (76.4%) by the NaOH catalyzed self-aldol condensation of 3,3,5-trimethylcyclohexanone which was carried out in a round bottom flask attached to the Dean-Stark apparatus. In the third step, the 3,5,5-trimethyl-2-(3,3,5-trimethylcyclohexylidene)cyclohexanone was hydrodeoxygenated under solvent-free conditions. High carbon yield (93.4%) of 1,1,3-trimethyl-5-(2,4,4-trimethylcyclohexyl)cyclohexane was obtained over the Ni/SiO 2 catalyst. The 1,1,3-trimethyl-5-(2,4,4-trimethylcyclohexyl)cyclohexane as obtained has a density of 0.858 g mL -1 and a freezing point of 222.2 K. As a potential application, it can be blended into conventional fuels (such as RP-1, RG-1, etc.) for rocket propulsion.

Modeling the effects of light, carbon dioxide, and temperature on the growth of potato

NASA Technical Reports Server (NTRS)

Yandell, B. S.; Najar, A.; Wheeler, R.; Tibbitts, T. W.

1988-01-01

This study examined the effects of light, temperature and carbon dioxide on the growth of potato (Solanum tuberosum L.) in a controlled environment in order to ascertain the best growing conditions for potato in life support systems in space. 'Norland' and 'Russet Burbank' were grown in 6-L pots of peat-vermiculite for 56 d in growth chambers at the University of Wisconsin Biotron. Environmental factor levels included continuous light (24-h photoperiod) at 250, 400, and 550 micromoles m-2 s-1 PPF; constant temperature at 16, 20, and 24 degrees C; and CO2 at approximately 400, 1000, and 1600 microliters L-1. Separate effects analysis and ridge analysis provided a means to examine the effects of individual environmental factors and to determine combinations of factors that are expected to give the best increases in yields over the central design point. The response surface of Norland indicated that tuber yields were highest with moderately low temperature (18.7 degrees C), low CO2 (400 microliters L-1) and high light (550 micromoles m-2 s-1 PPF). These conditions also favored shorter stem growth. Russet Burbank tuber yields were highest at moderately low temperature (17.5 degrees C), high CO2 (1600 microliters L-1) and medium analyses will be used to project the most efficient conditions for growth of potatoes in closed ecological life support systems (CELSS) in space colonies.

Improving the yield from fermentative hydrogen production.

PubMed

Kraemer, Jeremy T; Bagley, David M

2007-05-01

Efforts to increase H(2) yields from fermentative H(2) production include heat treatment of the inoculum, dissolved gas removal, and varying the organic loading rate. Although heat treatment kills methanogens and selects for spore-forming bacteria, the available evidence indicates H(2) yields are not maximized compared to bromoethanesulfonate, iodopropane, or perchloric acid pre-treatments and spore-forming acetogens are not killed. Operational controls (low pH, short solids retention time) can replace heat treatment. Gas sparging increases H(2) yields compared to un-sparged reactors, but no relationship exists between the sparging rate and H(2) yield. Lower sparging rates may improve the H(2) yield with less energy input and product dilution. The reasons why sparging improves H(2) yields are unknown, but recent measurements of dissolved H(2) concentrations during sparging suggest the assumption of decreased inhibition of the H(2)-producing enzymes is unlikely. Significant disagreement exists over the effect of organic loading rate (OLR); some studies show relatively higher OLRs improve H(2) yield while others show the opposite. Discovering the reasons for higher H(2) yields during dissolved gas removal and changes in OLR will help improve H(2) yields.

Ultrasonication and steam-explosion as chitin pretreatments for chitin oligosaccharide production by chitinases of Lecanicillium lecanii.

PubMed

Villa-Lerma, Guadalupe; González-Márquez, Humberto; Gimeno, Miquel; López-Luna, Alberto; Bárzana, Eduardo; Shirai, Keiko

2013-10-01

In this study, chitin oligosaccharides have been successfully produced using chitinases from submerged fermentation of Lecanicillium lecanii. The highest Hex, Chit and Prot production was 0.14, 0.26 and 2.05 U/mg of protein, respectively, which were attained varying pH from 5 to 8 after 96 h. Culture conditions conducted at constant pH of 6 resulted in significantly lower enzyme production. The crude enzyme was partially purified by salting out with (NH4)2SO4 followed by size exclusion chromatography to isolate the chitinase mixture for further chitin hydrolysis assays. In this regard, chitin substrates were pretreated with sonication and steam explosion prior to enzymatic reaction. Structural changes were observed with steam explosion with 11.28% reduction of the crystallinity index attained with the lowest chitin/water ratio (0.1g/mL). Pretreated chitins reached the highest production of reducing sugars (0.37 mg/mL) and GlcNAc (0.59 mg/mL) in 23.6% yield. Copyright © 2013 Elsevier Ltd. All rights reserved.

Catalytic Ethanol Dehydration over Different Acid-activated Montmorillonite Clays.

PubMed

Krutpijit, Chadaporn; Jongsomjit, Bunjerd

2016-01-01

In the present study, the catalytic dehydration of ethanol to obtain ethylene over montmorillonite clays (MMT) with mineral acid activation including H2SO4 (SA-MMT), HCl (HA-MMT) and HNO3 (NA-MMT) was investigated at temperature range of 200 to 400°C. It revealed that HA-MMT exhibited the highest catalytic activity. Ethanol conversion and ethylene selectivity were found to increase with increased reaction temperature. At 400°C, the HA-MMT yielded 82% of ethanol conversion having 78% of ethylene yield. At lower temperature (i.e. 200 to 300°C), diethyl ether (DEE) was a major product. The highest activity obtained from HA-MMT can be attributed to an increase of weak acid sites and acid density by the activation of MMT with HCl. It can be also proven by various characterization techniques that in most case, the main structure of MMT did not alter by acid activation (excepted for NA-MMT). Upon the stability test for 72 h during the reaction, the MMT and HA-MMT showed only slight deactivation due to carbon deposition. Hence, the acid activation of MMT by HCl is promising to enhance the catalytic dehydration of ethanol.

Effects of Carbonization Parameters of Moso-Bamboo-Based Porous Charcoal on Capturing Carbon Dioxide

PubMed Central

Jhan, Jhih-Wei; Cheng, Yi-Ming; Cheng, Hau-Hsein

2014-01-01

This study experimentally analyzed the carbon dioxide adsorption capacity of Moso-bamboo- (Phyllostachys edulis-) based porous charcoal. The porous charcoal was prepared at various carbonization temperatures and ground into powders with 60, 100, and 170 meshes, respectively. In order to understand the adsorption characteristics of porous charcoal, its fundamental properties, namely, charcoal yield, ash content, pH value, Brunauer-Emmett-Teller (BET) surface area, iodine number, pore volume, and powder size, were analyzed. The results show that when the carbonization temperature was increased, the charcoal yield decreased and the pH value increased. Moreover, the bamboo carbonized at a temperature of 1000°C for 2 h had the highest iodine sorption value and BET surface area. In the experiments, charcoal powders prepared at various carbonization temperatures were used to adsorb 1.854% CO2 for 120 h. The results show that the bamboo charcoal carbonized at 1000°C and ground with a 170 mesh had the best adsorption capacity, significantly decreasing the CO2 concentration to 0.836%. At room temperature and atmospheric pressure, the Moso-bamboo-based porous charcoal exhibited much better CO2 adsorption capacity compared to that of commercially available 350-mesh activated carbon. PMID:25225639

The Coupled Photochemistry of Ammonia and Acetylene: Applications to the Atmospheric Chemistry on Jupiter

NASA Astrophysics Data System (ADS)

Keane, Thomas Christopher

1995-01-01

The existence of hydrogen cyanide (HCN) in the highly reducing atmosphere of Jupiter was a surprising discovery (Tokunaga et al., 1981). Previous studies that tested the theoretical proposal of Kaye and Strobel (1983a) that the HCN observed on Jupiter is the result of NH _3 photolysis in the presence of C _2H_2 established that acetonitrile (CH_3CN) and acetaldazine (CH _3CH=NN=CHCH_3) are important intermediates in HCN formation (Ferris and Ishikawa, 1988). In this study the rates of formation of these compounds, and of other recently detected intermediates, have been determined in static photolysis experiments at 296 K and at temperatures which are closer to those found in the Jovian atmosphere. Experiments were also performed, using a photochemical flow reactor, that allowed for a better approximation of the mixing ratios of reactant gases (8 times 10^{ -4} for NH_3 and 1 times 10^{-5} for C_2H_2) and the process of advection in the Jovian atmosphere. An overall reaction pathway for HCN formation is proposed. Major intermediates and products found in these laboratory simulations that have not yet been observed on Jupiter are acetonitrile (CH_3CN), acetaldazine (CH_3CH=NN=CHCH _3), acetaldehyde hydrazone (CH_3 CH=NNH_2), N-ethylethylideneimine (CH_3CH=NC_2H _5), ethylamine (C_2H _5NH_2) and methylamine (CH _3NH_2). HCN is formed by the photolysis of NH_3/C _2H_2 mixtures (40:5 torr) at 296 K and at low temperature (208 K, 195 K and 180 K) with the highest quantum efficiency for HCN formation observed at 180 K. In static experiments using a high partial pressure of H_2 the quantum yield for HCN formation decreased three-fold relative to the 296 K photolyses when no H_2 was used. An additional ten-fold decrease in the quantum yield for HCN formation occurred when using the flow system. The quantum yields for acetaldazine and acetaldehyde hydrazone formation were found to vary inversely to that for HCN formation. For those static experiments which best simulate Jovian reaction conditions (H_2: NH_3 : C_2H_2 = 600: 7.5: 5 torr, 180 K) the following products and their quantum yields for formation were obtained: C_2H_4 (0.129), CH_3 CH=NN=CHCH_3 (0.079), CH _3CH=NNH_2 (0.049), C_2H_5NH_2 (0.038), CH_3NH_2 (0.003), CH_3CN (0.002), HCN (0.001) and CH_3CH=NC _2H_5 (0.001).

Enhanced bioprocessing of lignocellulose: Wood-rot fungal saccharification and fermentation of corn fiber to ethanol

NASA Astrophysics Data System (ADS)

Shrestha, Prachand

This research aims at developing a biorefinery platform to convert corn-ethanol coproduct, corn fiber, into fermentable sugars at a lower temperature with minimal use of chemicals. White-rot (Phanerochaete chrysosporium), brown-rot (Gloeophyllum trabeum) and soft-rot (Trichoderma reesei) fungi were used in this research to biologically break down cellulosic and hemicellulosic components of corn fiber into fermentable sugars. Laboratory-scale simultaneous saccharification and fermentation (SSF) process proceeded by in-situ cellulolytic enzyme induction enhanced overall enzymatic hydrolysis of hemi/cellulose from corn fiber into simple sugars (mono-, di-, tri-saccharides). The yeast fermentation of hydrolyzate yielded 7.1, 8.6 and 4.1 g ethanol per 100 g corn fiber when saccharified with the white-, brown-, and soft-rot fungi, respectively. The highest corn-to-ethanol yield (8.6 g ethanol/100 g corn fiber) was equivalent to 42 % of the theoretical ethanol yield from starch and cellulose in corn fiber. Cellulase, xylanase and amylase activities of these fungi were also investigated over a week long solid-substrate fermentation of corn fiber. G. trabeum had the highest activities for starch (160 mg glucose/mg protein.min) and on day three of solid-substrate fermentation. P. chrysosporium had the highest activity for xylan (119 mg xylose/mg protein.min) on day five and carboxymethyl cellulose (35 mg glucose/mg protein.min) on day three of solid-substrate fermentation. T. reesei showed the highest activity for Sigma cell 20 (54.8 mg glucose/mg protein.min) on day 5 of solid-substrate fermentation. The effect of different pretreatments on SSF of corn fiber by fungal processes was examined. Corn fiber was treated at 30 °C for 2 h with alkali [2% NaOH (w/w)], alkaline peroxide [2% NaOH (w/w) and 1% H2O 2 (w/w)], and by steaming at 100 °C for 2 h. Mild pretreatment resulted in improved ethanol yields for brown- and soft-rot SSF, while white-rot and Spezyme CP SSFs showed no improvement in ethanol yields. We showed that saccharification of lignocellulosic material with a wood-rot fungal process is quite feasible. Corn fiber from wet milling was best degraded to sugars using aerobic solid state fermentation with the soft-rot fungus T. reesei. However, it was shown that both the white-rot fungus P. chrysosporium and brown-rot fungus G. trabeum had the ability to produce additional consortia of hemi/cellulose degrading enzymes. It is likely that a consortium of enzymes from these fungi would be the best approach in saccharification of lignocellulose. In all cases, a subsequent anaerobic yeast process under submerged conditions is required to ferment the released sugars to ethanol. To our knowledge, this is the first time report on production of cellulolytic enzymes from wet-milled corn fiber using white- and brown-rot fungi for sequential fermentation of corn fiber hydrolyzate to ethanol. Keywords: lignocellulose, ethanol, biofuel, bioeconomy, biomass, renewable resources, corn fiber, pretreatment, solid-substrate fermentation, simultaneous saccharification and fermentation (SSF), white-rot fungus, brown-rot fungus, soft-rot fungus, fermentable sugars, enzyme activities, cellulytic enzymes Phanerochaete chrysosporium, Gloleophyllum trabeum, Trichoderma reesei, Saccharomyces cerevisiae.

Low-energy-electron interactions with DNA: approaching cellular conditions with atmospheric experiments

NASA Astrophysics Data System (ADS)

Alizadeh, Elahe; Sanche, Léon

2014-04-01

A novel technique has been developed to investigate low energy electron (LEE)-DNA interactions in the presence of small biomolecules (e.g., N2, O2, H2O) found near DNA in the cell nucleus, in order to simulate cellular conditions. In this technique, LEEs are emitted from a metallic surface exposed by soft X-rays and interact with DNA thin films at standard ambient temperature and pressure (SATP). Whereas atmospheric N2 had little effect on the yields of LEE-induced single and double strand breaks, both O2 and H2O considerably modified and increased such damage. The highest yields were obtained when DNA is embedded in a combined O2 and H2O atmosphere. In this case, the amount of additional double strand breaks was supper-additive. The effect of modifying the chemical and physical stability of DNA by platinum-based chemotherapeutic agents (Pt-drugs) including cisplatin, carboplatin and oxaliplatin was also investigated with this technique. The results obtained provide information on the role played by subexcitation-energy electrons and dissociative electron attachment in the radiosensitization of DNA by Pt-drugs, which is an important step to unravel the mechanisms of radiosensitisation of these agents in chemoradiation cancer therapy.

Formate production through carbon dioxide hydrogenation with recombinant whole cell biocatalysts.

PubMed

Alissandratos, Apostolos; Kim, Hye-Kyung; Easton, Christopher J

2014-07-01

The biological conversion of CO2 and H2 into formate offers a sustainable route to a valuable commodity chemical through CO2 fixation, and a chemical form of hydrogen fuel storage. Here we report the first example of CO2 hydrogenation utilising engineered whole-cell biocatalysts. Escherichia coli JM109(DE3) cells transformed for overexpression of either native formate dehydrogenase (FDH), the FDH from Clostridium carboxidivorans, or genes from Pyrococcus furiosus and Methanobacterium thermoformicicum predicted to express FDH based on their similarity to known FDH genes were all able to produce levels of formate well above the background, when presented with H2 and CO2, the latter in the form of bicarbonate. In the case of the FDH from P. furiosus the yield was highest, reaching more than 1 g L(-1)h(-1) when a hydrogen-sparging reactor design was used. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effect of Varying Acid Hydrolysis Condition in Gracilaria Sp. Fermentation Using Sasad

NASA Astrophysics Data System (ADS)

Mansuit, H.; Samsuri, M. D. C.; Sipaut, C. S.; Yee, C. F.; Yasir, S. M.; Mansa, R.

2015-04-01

Macroalgae or seaweed is being considered as promising feedstock for bioalcohol production due to high polysaccharides content. Polysaccharides can be converted into fermentable sugar through acid hydrolysis pre-treatment. In this study, the potential of using carbohydrate-rich macroalgae, Gracilaria sp. as feedstock for bioalcohol production via various acid hydrolysis conditions prior to the fermentation process was investigated and evaluated. The seaweed used in this research was from the red algae group, using species of Gracilaria sp. which was collected from Sg. Petani Kedah, Malaysia. Pre-treatment of substrate was done using H2SO4 and HCl with molarity ranging from 0.2M to 0.8M. The pretreatment time were varied in the range of 15 to 30 minutes. Fermentation was conducted using Sasad, a local Sabahan fermentation agent as a starter culture. Alcohol extraction was done using a distillation unit. Reducing sugar analysis was done by Benedict test method. Alcohol content analysis was done using specific gravity test. After hydrolysis, it was found out that acid hydrolysis at 0.2M H2SO4 and pre-treated for 20 minutes at 121°C has shown the highest reducing sugar content which has yield (10.06 mg/g) of reducing sugar. It was followed by other samples hydrolysis using 0.4M HCl with 30 minutes pre-treatment and 0.2M H2SO4, 15 minutes pre-treatment with yield of 8.06 mg/g and 5.75 mg/g reducing sugar content respectively. In conclusion, acid hydrolysis of Gracilaria sp. can produce higher reducing sugar yield and thus it can further enhance the bioalcohol production yield. Hence, acid hydrolysis of Gracilaria sp. should be studied more as it is an important step in the bioalcohol production and upscaling process.

In-situ biodiesel and sugar production from rice bran under subcritical condition

NASA Astrophysics Data System (ADS)

Zullaikah, Siti; Rahkadima, Yulia Tri

2015-12-01

An integrated method of producing biodiesel and sugar using subcritical water and methanol has been employed as a potential way to reduce the high cost of single biofuel production from rice bran. The effects of temperature, methanol to water ratio and reaction time on the biodiesel yield and purity, and the concentration of sugar in hydrolysate were investigated systematically. Biodiesel with yield and purity of 65.21%and 73.53%, respectively, was obtained from rice bran with initial free fatty acid (FFA) content of 37.64% under the following conditions: T= 200 oC, P= 4.0 MPa (using CO2 as pressurizing gas), ratio of rice bran/water/methanol of 1/2/6 (g/mL/mL), and 3 h of reaction time. FFAs level was reduced to 10.00% with crude biodiesel recovery of 88.69%. However, the highest biodiesel yield (67.39%) and crude biodiesel recovery (100.00%) were obtained by decreasing the amount of methanol so that the ratio of rice bran/water/methanol became 1/4/4, g/mL/mL. In addition, the highest sugar concentration of 0.98 g/L was obtained at 180 oC and 4.0 MPa with ratio of rice bran/water/methanol of 1/4/4 (g/mL/mL) and reaction time of 3 h. Since no catalyst was employed and the biodiesel and reducing sugar were produced directly from rice bran with high water and FFA contents, the process was simple and environmentally friendly, which would make the production of biofuel more economical and sustainable.

Factors affecting the formation of nitrogenous disinfection by-products during chlorination of aspartic acid in drinking water.

PubMed

Chen, Wei; Liu, Zhigang; Tao, Hui; Xu, Hang; Gu, Yanmei; Chen, Zhaolin; Yu, Jingjing

2017-01-01

The formation of emerging nitrogenous disinfection by-products (N-DBPs) from the chlorination of aspartic acid (Asp) was investigated. The yield of dichloroacetonitrile (DCAN) was higher than other N-DBPs, such as dichloroacetamide(DCAcAm) and chloropicrin (TCNM) during the chlorination of Asp. The formation of DCAN, DCAcAm, and TCNM all showed a trend of first increasing and then decreasing during the chlorination of Asp with increasing contact time. The dosage of chlorine had an impact on the formation of DCAN, DCAcAm, and TCNM. The highest yields of DCAN and DCAcAm appeared when the Cl 2 /Asp molar ratio was about 20, the yield of TCNM increased with increasing the Cl 2 /Asp molar ratio from 5 to 30 and TCNM was not produced when the ratio was less than 5. Cyanogen chloride (CNCl) was detected when the Cl 2 /Asp molar ratio was lower than 5. N-DBPs formation was influenced by pH. DCAN formation increased with increasing pH from 5 to 6 and then decreased with increasing pH from 6 to 9, but DCAcAm and TCNM increased with increasing pH from 5 to 8 and then decreased. Higher temperatures reduced the formation of DCAN and DCAcAm, but increased TCNM formation. DCAN and DCAcAm formation decreased, and relatively stable TCNM formation increased, with increasing free chlorine contact time during chloramination. N-nitrosodimethylamine (NDMA) was produced during chloramination of Asp and increased with prolonged chloramination contact time. The presence of bromide ions enhanced the yields of haloacetonitriles and shifted N-DBPs to more brominated species. Copyright © 2016 Elsevier B.V. All rights reserved.

Dilute sulfuric acid fractionation of Korean food waste for ethanol and lactic acid production by yeast.

PubMed

Kim, Yong Seon; Jang, Ji Yeon; Park, Seong Jik; Um, Byung Hwan

2018-04-01

Fermentation of food waste biomass can be used to produce biochemicals such as lactic acid and ethanol in a cost-effective manner. Korean food waste (KFW) dewatered by a screw press contains 23.1% glucan on a dry basis and is a potential raw material for the production of ethanol and lactic acid through fermentation. This study was conducted to optimize the dilute acid fractionation conditions for KFW fermentation with respect to the H 2 SO 4 concentration (0-0.8% w/v), temperature (130-190 °C), and residence time (1-128 min) using response surface methodology. Dilute sulfuric acid fractionation was carried out using a 30-mL stainless steel reactor under conditions, and then the dilute acid fractionation was scaled-up in 1-L and 7-L stainless steel reactors under the optimal conditions. The hydrolysate was concentrated, liquid-liquid extracted and neutralized for lactic acid and ethanol production. The highest concentration of glucose obtained from the KFW was 26.4 g/L using fractionation with 0.37% w/v H 2 SO 4 at 156 °C for 123.6 min. Using recombinant Saccharomyces cerevisiae containing a codon-optimized lactate dehydrogenase, the yield of lactic acid and ethanol was 77% of the theoretical yield for 17.4 g/L of fermentable sugar at pH 5.5. Additionally, the yield of ethanol produced by Issatchenkia orientalis was 89% of the theoretical yield for 25 g/L of fermentable sugar at pH 3. Copyright © 2018 Elsevier Ltd. All rights reserved.

The energy dependence of CO(v,J) produced from H2CO via the transition state, roaming, and triple fragmentation channels.

PubMed

Quinn, Mitchell S; Andrews, Duncan U; Nauta, Klaas; Jordan, Meredith J T; Kable, Scott H

2017-07-07

The dynamics of CO production from photolysis of H 2 CO have been explored over a 8000 cm -1 energy range (345 nm-266 nm). Two-dimensional ion imaging, which simultaneously measures the speed and angular momentum distribution of a photofragment, was used to characterise the distribution of rotational and translational energy and to quantify the branching fraction of roaming, transition state (TS), and triple fragmentation (3F) pathways. The rotational distribution for the TS channel broadens significantly with increasing energy, while the distribution is relatively constant for the roaming channel. The branching fraction from roaming is also relatively constant at 20% of the observed CO. Above the 3F threshold, roaming decreases in favour of triple fragmentation. Combining the present data with our previous study on the H-atom branching fractions and published quantum yields for radical and molecular channels, absolute quantum yields were determined for all five dissociation channels for the entire S 1 ←S 0 absorption band, covering almost 8000 cm -1 of excitation energy. The S 0 radical and TS molecular channels are the most important over this energy range. The absolute quantum yield of roaming is fairly constant ∼5% at all energies. The T 1 radical channel is important (20%-40%) between 1500 and 4000 cm -1 above the H + HCO threshold, but becomes unimportant at higher energy. Triple fragmentation increases rapidly above its threshold reaching a maximum of 5% of the total product yield at the highest energy.

Cyclolinear Oligo- and Poly(iminoborane)s: The Missing Link in Inorganic Main-Group Macromolecular Chemistry.

PubMed

Ayhan, Ozan; Riensch, Nicolas A; Glasmacher, Clemens; Helten, Holger

2018-04-17

The reaction of n-C 8 H 17 B[N(Me)SiMe 3 ] 2 (1) with n-C 8 H 17 BCl 2 (2 a) yielded, instead of a linear poly(iminoborane), the aminoborane n-C 8 H 17 B(Cl)N(Me)SiMe 3 (4) and after cyclotrimerization the borazine cyclo-(n-C 8 H 17 BNMe) 3 (6). Side reactions that result in borazine formation were effectively suppressed if 1,3-bis(trimethylsilyl)-1,3,2-diazaborolidines 7 were employed as co-monomers in combination with dichloro- or dibromoboranes 2 or 8, respectively. Silicon/boron exchange polycondensation led to oligo(iminoborane)s 11 a,b,ac,d. Alternative synthetic routes to such species involve Sn/B exchange of 1,3-bis(trimethylstannyl)-2-n-octyl-1,3,2-diazaborolidine (16) and n-C 8 H 17 BBr 2 (8 a), and the initiated polycondensation of the dormant monomer 14 in the presence of a Brønsted acid (HCl, HOTf, or HNTf 2 ; Tf=trifluoromethylsulfonyl). Although an attempt to obtain an oligo-/poly(iminoborane) with phenyl side groups yielded only insoluble material, the incorporation of aryl groups was proven for a derivative with both phenyl and n-octyl boron substituents (11 ac), as well as for a derivative with 4-n-butylphenyl side groups (11 d). The highest-molecular-weight sample obtained was 11 ac. Featuring about 18 catenated BN units, on average, this is the closest approach to a poly(iminoborane) known. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Succinic acid-producing biofilms of Actinobacillus succinogenes: reproducibility, stability and productivity.

PubMed

Maharaj, K; Bradfield, M F A; Nicol, W

2014-09-01

Continuous anaerobic fermentations were performed in a biofilm reactor packed with Poraver® beads. Dilution rates (D) varied between 0.054 and 0.72 h(-1), and D-glucose and CO2 gas were used as carbon substrates. Steady-state conditions were shown to be repeatable and independent of the operational history. Production stability was achieved over periods exceeding 80 h at values of D below 0.32 h(-1). In these situations, steady-state variation (expressed as fluctuations in NaOH neutralisation flow rates) exhibited a standard deviation of less than 5 % while no indication of biofilm deactivation was detected. The total biomass amount was found to be independent of the dilution rate with an average dry concentration of 23.8 ± 2.9 g L(-1) obtained for all runs. This suggests that the attachment area controls the extent of biofilm accumulation. Specific succinic acid (SA) productivities, based on the total biomass amount, exhibited a substantial decrease with decreasing D. An SA volumetric productivity of 10.8 g L(-1) h(-1) was obtained at D = 0.7 h(-1)-the highest value reported to date in Actinobacillus succinogenes fermentations. SA yields on glucose increased with decreasing D, with a yield of 0.90 ± 0.01 g g(-1) obtained at a D of 0.054 h(-1). Production of formic acid approached zero with decreasing D, while the succinic to acetic acid ratio increased with decreasing D, resulting in an increasing SA yield on glucose.

Preparation and Storage of High-Titer Lactic Streptococcus Bacteriophages1

PubMed Central

Nyiendo, J.; Seidler, Ramon J.; Sandine, W. E.; Elliker, P. R.

1974-01-01

Various techniques were employed for preparation of high-titer bacteriophage lysates of Streptococcus lactis, S. cremoris, and S. diacetilactis strains. Infection of a 4-h host culture in litmus milk at 30 C yielded the highest titers (2 × 109 to 4 × 1011 plaque-forming units/ml) for most phages. Host infection in lactose-containing broth produced similar virus numbers only when 0.1 M tris(hydroxymethyl)aminomethane buffer stabilized the pH. The pH at the time of infection as well as the inoculum phage titer were critical in obtaining high titers. Optimum conditions for infection in broth were coupled with a polyethylene glycol concentration procedure to routinely produce milligram quantities of phage from 1 liter of lysate. Neutralization of whey lysates, as a means of storage, offered no survival advantage over unneutralized samples. Storage of phage lysates in a 15% glycerol whey solution at -22 C yielded a high rate of survival in most cases, even with repeated freezing and thawing, over a period of 24 months. PMID:16349981

Catalytic Transfer Hydrogenation of Furfural to 2-Methylfuran and 2-Methyltetrahydrofuran over Bimetallic Copper-Palladium Catalysts.

PubMed

Chang, Xin; Liu, An-Feng; Cai, Bo; Luo, Jin-Yue; Pan, Hui; Huang, Yao-Bing

2016-12-08

The catalytic transfer hydrogenation of furfural to the fuel additives 2-methylfuran (2-MF) and 2-methyltetrahydrofuran (2-MTHF) was investigated over various bimetallic catalysts in the presence of the hydrogen donor 2-propanol. Of all the as-prepared catalysts, bimetallic Cu-Pd catalysts showed the highest catalytic activities towards the formation of 2-MF and 2-MTHF with a total yield of up to 83.9 % yield at 220 °C in 4 h. By modifying the Pd ratios in the Cu-Pd catalyst, 2-MF or 2-MTHF could be obtained selectively as the prevailing product. The other reaction conditions also had a great influence on the product distribution. Mechanistic studies by reaction monitoring and intermediate conversion revealed that the reaction proceeded mainly through the hydrogenation of furfural to furfuryl alcohol, which was followed by deoxygenation to 2-MF in parallel to deoxygenation/ring hydrogenation to 2-MTHF. Finally, the catalyst showed a high reactivity and stability in five catalyst recycling runs, which represents a significant step forward toward the catalytic transfer hydrogenation of furfural. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Acid Lipase from Candida viswanathii: Production, Biochemical Properties, and Potential Application

PubMed Central

de Almeida, Alex Fernando; Carmona, Eleonora Cano

2013-01-01

Influences of environmental variables and emulsifiers on lipase production of a Candida viswanathii strain were investigated. The highest lipase activity (101.1 U) was observed at 210 rpm, pH 6.0, and 27.5°C. Other fermentation parameters analyzed showed considerable rates of biomass yield (Y L/S = 1.381 g/g), lipase yield (Y L/S = 6.892 U/g), and biomass productivity (P X = 0.282 g/h). Addition of soybean lecithin increased lipase production in 1.45-fold, presenting lipase yield (Y L/S) of 10.061 U/g. Crude lipase presented optimal activity at acid pH of 3.5, suggesting a new lipolytic enzyme for this genus and yeast in general. In addition, crude lipase presented high stability in acid conditions and temperature between 40 and 45°C, after 24 h of incubation in these temperatures. Lipase remained active in the presence of organic solvents maintaining above 80% activity in DMSO, methanol, acetonitrile, ethanol, acetone, 1-propanol, isopropanol, and 2-propanol. Effectiveness for the hydrolysis of a wide range of natural triglycerides suggests that this new acid lipase has high potential application in the oleochemical and food industries for hydrolysis and/or modification of triacylglycerols to improve the nutritional properties. PMID:24350270

Mono- and tri-ester hydrogenolysis using tandem catalysis. Scope and mechanism.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lohr, Tracy L.; Li, Zhi; Assary, Rajeev S.

The scope and mechanism of thermodynamically leveraged ester RC(O)O-R' bond hydrogenolysis by tandem metal triflate + supported Pd catalysts are investigated both experimentally and theoretically by DFT and energy span analysis. This catalytic system has a broad scope, with relative cleavage rates scaling as, tertiary 4 secondary 4 primary ester at 1 bar H-2, yielding alkanes and carboxylic acids with high conversion and selectivity. Benzylic and allylic esters display the highest activity. The rate law is nu = k[M(OTf )(n)](1)[ester](0)[H-2](0) with an H/D kinetic isotope effect = 6.5 +/- 0.5, implying turnover-limiting C-H scission following C-O cleavage, in agreement withmore » theory. Intermediate alkene products are then rapidly hydrogenated. Applying this approach with the very active Hf(OTf)(4) catalyst to bio-derived triglycerides affords near-quantitative yields of C-3 hydrocarbons rather than glycerol. From model substrates, it is found that RC(O)O-R' cleavage rates are very sensitive to steric congestion and metal triflate identity. For triglycerides, primary/external glyceryl CH2-O cleavage predominates over secondary/internal CH-O cleavage, with the latter favored by less acidic or smaller ionic radius metal triflates, raising the diester selectivity to as high as 48% with Ce(OTf)(3).« less

A study on pyrolysis of Canada thistle (Cirsium arvense) with titania based catalysts for bio-fuel production.

PubMed

Aysu, Tevfik

2016-11-01

The catalytic pyrolysis of Cirsium arvense was performed with titania supported catalysts under the operating conditions of 500°C, 40°C/min heating rate, 100mL/min N2 flow rate in a fixed bed reactor for biofuel production. The effect of catalysts on product yields was investigated. The amount of pyrolysis products (bio-char, bio-oil, gas) and the composition of the produced bio-oils were determined by proton nuclear magnetic resonance ((1)H NMR), Fourier transform infrared spectroscopy (FT-IR), gas chromatography/mass spectrometry (GC-MS) and elemental analysis (EA) techniques. Thistle bio-oils had lower O/C and H/C molar ratios compared to feedstock. The highest bio-char and bio-oil yields of 29.32wt% and 36.71wt% were obtained in the presence of Ce/TiO2 and Ni/TiO2 catalysts respectively. GC-MS identified 97 different compounds in the bio-oils obtained from thistle pyrolysis. (1)H NMR analysis showed that the bio-oils contained ∼55-77% aliphatic and ∼6-19% aromatic structural units. Copyright © 2016 Elsevier Ltd. All rights reserved.

Bio-oil production from hydrothermal liquefaction of Pteris vittata L.: Effects of operating temperatures and energy recovery.

PubMed

Chen, Jinbo

2018-06-14

Hyper-accumulator biomass, Pteris vittata L., was hydrothermally converted into bio-oils via hydrothermal liquefaction (HTL) in sub-supercritical water. The distributions and characterizations of various products as well as energy recovery under different temperatures (250-390 °C) were investigated. The highest bio-oil yield of 16.88% was obtained at 350 °C with the hydrothermal conversion of 61.79%, where the bio-oil was dominated by alcohols, esters, phenols, ketones and acidic compounds. The higher heating values of bio-oil were in the range of 19.93-35.45 MJ/kg with a H/C ratio of 1.26-1.46, illustrating its high energy density and potential for use as an ideal liquid fuel. The main gaseous products were CO 2 , H 2 , CO, and CH 4 with the H 2 yield peaking at 22.94%. The total energy recovery from bio-oils and solid residues fell within the range of 37.72-45.10%, highlighting the potential of HTL to convert hyper-accumulator biomass into valuable fuels with high conversion efficiency. Copyright © 2018 Elsevier Ltd. All rights reserved.

Saccharification of sunflower stalks using lignocellulases from a fungal consortium comprising Pholiota adiposa and Armillaria gemina.

PubMed

Ramachandran, Priyadharshini; Kim, Tae-Su; Dhiman, Saurabh Sudha; Li, Jinglin; Park, Ji-Hyun; Choi, Joon-Ho; Kim, Jae Young; Kim, Dongwook; Lee, Jung-Kul

2015-09-01

Lignocellulases from Armillaria gemina and Pholiota adiposa are efficient in hydrolyzing aspen and poplar biomass, respectively. In the present study, lignocellulosic enzymes obtained from a fungal consortium comprising P. adiposa and A. gemina were used for the saccharification of sunflower stalks. Sunflower stalks were thermochemically pretreated using 2 % NaOH at 50 °C for 24 h. The saccharification process parameters including substrate concentration, enzyme loading, pH, and temperature were optimized using response surface methodology to improve the saccharification yield. The highest enzymatic hydrolysis (84.3 %) was obtained using the following conditions: enzyme loading 10 FPU/g-substrate, substrate 5.5 %, temperature 50 °C, and pH 4.5. The hydrolysis yield obtained using the enzymes from the fungal consortium was equivalent to that obtained using a mixture of commercial enzymes Celluclast and Novozyme β-glucosidase. Addition of up to 500 ppm of heavy metal ions (As, Cu, Fe, Mn, Ni, Pb, and Zn) during saccharification did not significantly affect the saccharification yield. Thus, the biomass grown for phytoremediation of heavy metals can be used for the production of reducing sugars followed by ethanol fermentation.

Thermogravimetric analysis and fast pyrolysis of Milkweed.

PubMed

Kim, Seung-Soo; Agblevor, Foster A

2014-10-01

Pyrolysis of Milkweed was carried out in a thermogravimetric analyzer and a bubbling fluidized bed reactor. Total liquid yield of Milkweed pyrolysis was between 40.74% and 44.19 wt% between 425 °C and 550 °C. The gas yield increased from 27.90 wt% to 33.33 wt% with increasing reaction temperature. The higher heating values (HHV) of the Milkweed bio-oil were relatively high (30.33-32.87 MJ/kg) and varied with reaction temperature, feeding rate and fluidization velocity. The selectivity for CO2 was highest within non-condensable gases, and the molar ratio of CO2/CO was about 3 at the different reaction conditions. The (13)C NMR analysis, of the bio-oil showed that the relative concentration carboxylic group and its derivatives was higher at 425 °C than 475 °C, which resulted in slightly higher oxygen content in bio-oil. The pH of aqueous phase obtained at 475 °C was 7.37 which is the highest reported for any lignocellulosic biomass pyrolysis oils. Copyright © 2014 Elsevier Ltd. All rights reserved.

Broiler performance, body weight variance, feed and water intake, and carcass quality at different stocking densities.

PubMed

Feddes, J J R; Emmanuel, E J; Zuidhoft, M J

2002-06-01

The effects of four stocking and water nipple densities on broiler performance and carcass traits were measured in two trials. The stocking densities of 23.8, 17.9, 14.3, and 11.9 birds/m2 corresponded to 260, 195, 156, and 130 birds per pen, respectively. The water nipple densities were 5, 10, 15, and 20 birds per water nipple. Birds in Trial 1 were processed at Day 39 and those in Trial 2 were processed at Day 42. Water and feed were provided ad libitum and light was provided 23 h/ d. Water nipple density had no effect on broiler performance or carcass quality. Birds grown at 23.8 birds/m2 had lower BW (1,898 g) and carcass weights (1,334 g), whereas birds grown at 14.3 birds/m2 had the highest BW (1,985 g) and carcass weights (1,432 g). Although the treatment with 23.8 birds/m2 gave the lowest BW, the yield of broilers per unit of floor space was highest (46.0 kg/m2). The coefficient of variation for BW was higher in the treatment with 11.9 birds/m2 (15.3 %) than in the other treatments (13.0%). The birds in the treatment with 11.9 birds/m2 consumed the least feed (2,993 g/bird) and those in the 14.3 birds/m2 treatment consumed the most feed (3,183 g/bird). The amount of water consumed and the water to feed ratio was highest in the 23.8 birds/m2 treatment (5,546 mL/bird and 1.85 mL/g, respectively). Stocking density had no effect on mortality, breast yield, carcass grading, incidence of scratches, or carcass quality. It was concluded high yield per unit area with good carcass quality could be achieved when ventilation rate and air circulation were adequate.

Response of rice genotypes to weed competition in dry direct-seeded rice in India.

PubMed

Mahajan, Gulshan; Ramesha, Mugalodi S; Chauhan, Bhagirath S

2014-01-01

The differential weed-competitive abilities of eight rice genotypes and the traits that may confer such attributes were investigated under partial weedy and weed-free conditions in naturally occurring weed flora in dry direct-seeded rice during the rainy seasons of 2011 and 2012 at Ludhiana, Punjab, India. The results showed genotypic differences in competitiveness against weeds. In weed-free plots, grain yield varied from 6.6 to 8.9 t ha(-1) across different genotypes; it was lowest for PR-115 and highest for the hybrid H-97158. In partial weedy plots, grain yield and weed biomass at flowering varied from 3.6 to 6.7 t ha(-1) and from 174 to 419 g m(-2), respectively. In partial weedy plots, grain yield was lowest for PR-115 and highest for PR-120. Average yield loss due to weed competition ranged from 21 to 46% in different rice genotypes. The study showed that early canopy closure, high leaf area index at early stage, and high root biomass and volume correlated positively with competitiveness. This study suggests that some traits (root biomass, leaf area index, and shoot biomass at the early stage) could play an important role in conferring weed competitiveness and these traits can be explored for dry-seeded rice.

Response of Rice Genotypes to Weed Competition in Dry Direct-Seeded Rice in India

PubMed Central

Mahajan, Gulshan; Ramesha, Mugalodi S.; Chauhan, Bhagirath S.

2014-01-01

The differential weed-competitive abilities of eight rice genotypes and the traits that may confer such attributes were investigated under partial weedy and weed-free conditions in naturally occurring weed flora in dry direct-seeded rice during the rainy seasons of 2011 and 2012 at Ludhiana, Punjab, India. The results showed genotypic differences in competitiveness against weeds. In weed-free plots, grain yield varied from 6.6 to 8.9 t ha−1 across different genotypes; it was lowest for PR-115 and highest for the hybrid H-97158. In partial weedy plots, grain yield and weed biomass at flowering varied from 3.6 to 6.7 t ha−1 and from 174 to 419 g m−2, respectively. In partial weedy plots, grain yield was lowest for PR-115 and highest for PR-120. Average yield loss due to weed competition ranged from 21 to 46% in different rice genotypes. The study showed that early canopy closure, high leaf area index at early stage, and high root biomass and volume correlated positively with competitiveness. This study suggests that some traits (root biomass, leaf area index, and shoot biomass at the early stage) could play an important role in conferring weed competitiveness and these traits can be explored for dry-seeded rice. PMID:25093205

Batch dark fermentation from enzymatic hydrolyzed food waste for hydrogen production.

PubMed

Han, Wei; Ye, Min; Zhu, Ai Jun; Zhao, Hong Ting; Li, Yong Feng

2015-09-01

A combination bioprocess of solid-state fermentation (SSF) and dark fermentative hydrogen production from food waste was developed. Aspergillus awamori and Aspergillus oryzae were utilized in SSF from food waste to generate glucoamylase and protease which were used to hydrolyze the food waste suspension to get the nutrients-rich (glucose and free amino nitrogen (FAN)) hydrolysate. Both glucose and FAN increased with increasing of food waste mass ratio from 4% to 10% (w/v) and the highest glucose (36.9 g/L) and FAN (361.3mg/L) were observed at food waste mass ratio of 10%. The food waste hydrolysates were then used as the feedstock for dark fermentative hydrogen production by heat pretreated sludge. The best hydrogen yield of 39.14 ml H2/g food waste (219.91 ml H2/VSadded) was achieved at food waste mass ratio of 4%. The proposed combination bioprocess could effectively accelerate the hydrolysis rate, improve raw material utilization and enhance hydrogen yield. Copyright © 2015 Elsevier Ltd. All rights reserved.

Soil Fertility Status, Nutrient Uptake, and Maize (Zea mays L.) Yield Following Organic Matters and P Fertilizer Application on Andisol

NASA Astrophysics Data System (ADS)

Minardi, S.; Harieni, S.; Anasrullah, A.; Purwanto, H.

2017-04-01

Objective of this study were to elucidate effects of organic matters and P fertilizer application on soil fertility status, nutrient uptake and maize yield in the Andisol. This experiment consisted of two factors. The first factor comprised of four levels of organic matters input (without organic matter, manure, rice straw, and Gliricidia sepium leaves), with the application dosage 10 t.ha-1 and the second factor comprised of three levels of P fertilizer application (without P addition (control), 50 kg P2O5 ha-1, 100 kg P2O5 ha-1). Results of this study showed that organic matters and P fertilizer application improved soil fertility status, especially pH, soil organic C, cation exchange capacity (CEC), available P which resulted in an increase in P uptake that improve yield of maize. The highest yield of maize (corn cob) was obtained through application Gliricida sepium (8.40 t.ha-1), followed by manure (6.02 t.ha-1) and rice straw (5.87 t.ha-1). Application of 50 kg P2O5 Ha-1 yield was (5.76 t.ha-1) and application of 100 Kg P2O5 Ha-1 yield was (6.12 t.ha-1).

Bioreactors configured with distributors and carriers enhance the performance of continuous dark hydrogen fermentation.

PubMed

Lo, Yung-Chung; Lee, Kuo-Shing; Lin, Ping-Jei; Chang, Jo-Shu

2009-10-01

Anaerobic granular sludge bed (AnGSB) bioreactors were supplemented with activated carbon carriers and combined with distributors (e.g., acrylic resin board, stainless steel net and plastic net) installed at different locations to investigate the effect of distributor/carrier on biohydrogen production efficiency. The results show that plastic net stimulated the substrate/microorganisms contact and sludge granulation, thereby leading to a much better H(2) production performance when compared with those obtained from traditional CSTR. The highest H(2) production rate (7.89 L/h/L) and yield (3.42 mol H(2)/mol sucrose) were obtained when two pieces of plastic nets were installed at both 4 cm and 16 cm from the bottom of AnGSB without carrier addition and the bioreactor was operated at a HRT of 0.5h. For the AnGSB installed with two pieces of plastic net distributors, addition of carriers led to significant improvement on the H(2) production efficiency at a longer HRT (1-4h) when compared with the carrier-absent system.

Halocarbon emissions by selected tropical seaweeds: species-specific and compound-specific responses under changing pH.

PubMed

Mithoo-Singh, Paramjeet Kaur; Keng, Fiona S-L; Phang, Siew-Moi; Leedham Elvidge, Emma C; Sturges, William T; Malin, Gill; Abd Rahman, Noorsaadah

2017-01-01

Five tropical seaweeds, Kappaphycus alvarezii (Doty) Doty ex P.C. Silva, Padina australis Hauck, Sargassum binderi Sonder ex J. Agardh (syn. S. aquifolium (Turner) C. Agardh), Sargassum siliquosum J. Agardh and Turbinaria conoides (J. Agardh) Kützing, were incubated in seawater of pH 8.0, 7.8 (ambient), 7.6, 7.4 and 7.2, to study the effects of changing seawater pH on halocarbon emissions. Eight halocarbon species known to be emitted by seaweeds were investigated: bromoform (CHBr 3 ), dibro-momethane (CH 2 Br 2 ), iodomethane (CH 3 I), diiodomethane (CH 2 I 2 ), bromoiodomethane (CH 2 BrI), bromochlorometh-ane (CH 2 BrCl), bromodichloromethane (CHBrCl 2 ), and dibro-mochloromethane (CHBr 2 Cl). These very short-lived halocarbon gases are believed to contribute to stratospheric halogen concentrations if released in the tropics. It was observed that the seaweeds emit all eight halocarbons assayed, with the exception of K. alvarezii and S. binderi for CH 2 I 2 and CH 3 I respectively, which were not measurable at the achievable limit of detection. The effect of pH on halocarbon emission by the seaweeds was shown to be species-specific and compound specific. The highest percentage changes in emissions for the halocarbons of interest were observed at the lower pH levels of 7.2 and 7.4 especially in Padina australis and Sargassum spp., showing that lower seawater pH causes elevated emissions of some halocarbon compounds. In general the seaweed least affected by pH change in terms of types of halocarbon emission, was P. australis . The commercially farmed seaweed K. alvarezii was very sensitive to pH change as shown by the high increases in most of the compounds in all pH levels relative to ambient. In terms of percentage decrease in maximum quantum yield of photosynthesis ( F v ∕ F m ) prior to and after incubation, there were no significant correlations with the various pH levels tested for all seaweeds. The correlation between percentage decrease in the maximum quantum yield of photosynthesis ( F v ∕ F m ) and halocarbon emission rates, was significant only for CH 2 BrCl emission by P. australis ( r  = 0.47; p  ≤ 0.04), implying that photosynthesis may not be closely linked to halocarbon emissions by the seaweeds studied. Bromine was the largest contributor to the total mass of halogen emitted for all the seaweeds at all pH. The highest total amount of bromine emitted by K. alvarezii (an average of 98% of total mass of halogens) and the increase in the total amount of chlorine with decreasing seawater pH fuels concern for the expanding seaweed farming activities in the ASEAN region.

Halocarbon emissions by selected tropical seaweeds: species-specific and compound-specific responses under changing pH

PubMed Central

Leedham Elvidge, Emma C.; Sturges, William T.; Malin, Gill; Abd Rahman, Noorsaadah

2017-01-01

Five tropical seaweeds, Kappaphycus alvarezii (Doty) Doty ex P.C. Silva, Padina australis Hauck, Sargassum binderi Sonder ex J. Agardh (syn. S. aquifolium (Turner) C. Agardh), Sargassum siliquosum J. Agardh and Turbinaria conoides (J. Agardh) Kützing, were incubated in seawater of pH 8.0, 7.8 (ambient), 7.6, 7.4 and 7.2, to study the effects of changing seawater pH on halocarbon emissions. Eight halocarbon species known to be emitted by seaweeds were investigated: bromoform (CHBr3), dibro­momethane (CH2Br2), iodomethane (CH3I), diiodomethane (CH2I2), bromoiodomethane (CH2BrI), bromochlorometh­ane (CH2BrCl), bromodichloromethane (CHBrCl2), and dibro­mochloromethane (CHBr2Cl). These very short-lived halocarbon gases are believed to contribute to stratospheric halogen concentrations if released in the tropics. It was observed that the seaweeds emit all eight halocarbons assayed, with the exception of K. alvarezii and S. binderi for CH2I2 and CH3I respectively, which were not measurable at the achievable limit of detection. The effect of pH on halocarbon emission by the seaweeds was shown to be species-specific and compound specific. The highest percentage changes in emissions for the halocarbons of interest were observed at the lower pH levels of 7.2 and 7.4 especially in Padina australis and Sargassum spp., showing that lower seawater pH causes elevated emissions of some halocarbon compounds. In general the seaweed least affected by pH change in terms of types of halocarbon emission, was P. australis. The commercially farmed seaweed K. alvarezii was very sensitive to pH change as shown by the high increases in most of the compounds in all pH levels relative to ambient. In terms of percentage decrease in maximum quantum yield of photosynthesis (Fv∕Fm) prior to and after incubation, there were no significant correlations with the various pH levels tested for all seaweeds. The correlation between percentage decrease in the maximum quantum yield of photosynthesis (Fv∕Fm) and halocarbon emission rates, was significant only for CH2BrCl emission by P. australis (r = 0.47; p ≤ 0.04), implying that photosynthesis may not be closely linked to halocarbon emissions by the seaweeds studied. Bromine was the largest contributor to the total mass of halogen emitted for all the seaweeds at all pH. The highest total amount of bromine emitted by K. alvarezii (an average of 98% of total mass of halogens) and the increase in the total amount of chlorine with decreasing seawater pH fuels concern for the expanding seaweed farming activities in the ASEAN region. PMID:28149690

Effect of torrefaction pretreatment and catalytic pyrolysis on the pyrolysis poly-generation of pine wood.

PubMed

Chen, Dengyu; Li, Yanjun; Deng, Minsi; Wang, Jiayang; Chen, Miao; Yan, Bei; Yuan, Qiqiang

2016-08-01

Torrefaction of pine wood was performed in a tube furnace at three temperatures (220, 250, and 280°C) for 30min. Then catalytic pyrolysis of raw and torrefied pine wood was performed using HZSM-5 catalyst in a fixed-bed pyrolysis reactor at 550°C for 15min. Torrefaction pretreatment and catalytic pyrolysis have an very important effect on the yield, property, and energy distribution of pyrolysis products. The results showed that the yield of biochar rapidly increased, while that of bio-oil decreased with increasing torrefaction temperature. The oxy-compound content of bio-oil, such as acids and aldehydes, sharply decreased. However, the aromatic hydrocarbon content not only increased but also further promoted by HZSM-5 catalyst. With highest mass yields and energy yields, biochar was also the very important product of pyrolysis. The oxygen content in biomass was mainly removed in the form of CO2 and H2O, leading to increasing CO2 content in non-condensable gas. Copyright © 2016 Elsevier Ltd. All rights reserved.

Production, purification and application of extracellular chitinase from Cellulosimicrobium cellulans 191

PubMed Central

Fleuri, Luciana F.; Kawaguti, Haroldo Y.; Sato, Hélia H.

2009-01-01

This study concerned the production, purification and application of extracellular chitinase from Cellulosimicrobium cellulans strain 191. In shaken flasks the maximum yield of chitinase was 6.9 U/mL after 72 h of cultivation at 25°C and 200 rpm. In a 5 L fermenter with 1.5 vvm aeration, the highest yield obtained was 4.19 U/mL after 168 h of fermentation at 25°C and 200 rpm, and using 3 vvm, it was 4.38 U/mL after 144 h of fermentation. The chitinase (61 KDa) was purified about 6.65 times by Sepharose CL 4B 200 gel filtration with a yield of 46.61%. The purified enzyme was able to lyse the cell walls of some fungi and to form protoplasts. PMID:24031407

Bioethanol production from microwave-assisted acid or alkali-pretreated agricultural residues of cassava using separate hydrolysis and fermentation (SHF).

PubMed

Pooja, N S; Sajeev, M S; Jeeva, M L; Padmaja, G

2018-01-01

The effect of microwave (MW)-assisted acid or alkali pretreatment (300 W, 7 min) followed by saccharification with a triple enzyme cocktail (Cellic, Optimash BG and Stargen) with or without detoxification mix on ethanol production from three cassava residues (stems, leaves and peels) by Saccharomyces cerevisiae was investigated. Significantly higher fermentable sugar yields (54.58, 47.39 and 64.06 g/L from stems, leaves and peels, respectively) were obtained after 120 h saccharification from MW-assisted alkali-pretreated systems supplemented (D+) with detoxification chemicals (Tween 20 + polyethylene glycol 4000 + sodium borohydride) compared to the non-supplemented (D0) or MW-assisted acid-pretreated systems. The percentage utilization of reducing sugars during fermentation (48 h) was also the highest (91.02, 87.16 and 89.71%, respectively, for stems, leaves and peels) for the MW-assisted alkali-pretreated (D+) systems. HPLC sugar profile indicated that glucose was the predominant monosaccharide in the hydrolysates from this system. Highest ethanol yields ( Y E , g/g), fermentation efficiency (%) and volumetric ethanol productivity (g/L/h) of 0.401, 78.49 and 0.449 (stems), 0.397, 77.71 and 0.341 (leaves) and 0.433, 84.65 and 0.518 (peels) were also obtained for this system. The highest ethanol yields (ml/kg dry biomass) of ca. 263, 200 and 303, respectively, for stems, leaves and peels from the MW-assisted alkali pretreatment (D+) indicated that this was the most effective pretreatment for cassava residues.

Biohydrogen production by dark fermentation of glycerol using Enterobacter and Citrobacter Sp.

PubMed

Maru, Biniam T; Constanti, Magda; Stchigel, Alberto M; Medina, Francesc; Sueiras, Jesus E

2013-01-01

Glycerol is an attractive substrate for biohydrogen production because, in theory, it can produce 3 mol of hydrogen per mol of glycerol. Moreover, glycerol is produced in substantial amounts as a byproduct of producing biodiesel, the demand for which has increased in recent years. Therefore, hydrogen production from glycerol was studied by dark fermentation using three strains of bacteria: namely, Enterobacter spH1, Enterobacter spH2, and Citrobacter freundii H3 and a mixture thereof (1:1:1). It was found that, when an initial concentration of 20 g/L of glycerol was used, all three strains and their mixture produced substantial amounts of hydrogen ranging from 2400 to 3500 mL/L, being highest for C. freundii H3 (3547 mL/L) and Enterobacter spH1 (3506 mL/L). The main nongaseous fermentation products were ethanol and acetate, albeit in different ratios. For Enterobacter spH1, Enterobacter spH2, C. freundii H3, and the mixture (1:1:1), the ethanol yields (in mol EtOH/mol glycerol consumed) were 0.96, 0.67, 0.31, and 0.66, respectively. Compared to the individual strains, the mixture (1:1:1) did not show a significantly higher hydrogen level, indicating that there was no synergistic effect. Enterobacter spH1 was selected for further investigation because of its higher yield of hydrogen and ethanol. Copyright © 2012 American Institute of Chemical Engineers (AIChE).

Large-moment antiferromagnetic order in overdoped high-Tc superconductor 154SmFeAsO1-x D x .

PubMed

Iimura, Soshi; Okanishi, Hiroshi; Matsuishi, Satoru; Hiraka, Haruhiro; Honda, Takashi; Ikeda, Kazutaka; Hansen, Thomas C; Otomo, Toshiya; Hosono, Hideo

2017-05-30

In iron-based superconductors, high critical temperature ( T c ) superconductivity over 50 K has only been accomplished in electron-doped hRE FeAsO ( hRE is heavy rare earth ( RE ) element). Although hRE FeAsO has the highest bulk T c (58 K), progress in understanding its physical properties has been relatively slow due to difficulties in achieving high-concentration electron doping and carrying out neutron experiments. Here, we present a systematic neutron powder diffraction study of 154 SmFeAsO 1- x D x , and the discovery of a long-range antiferromagnetic ordering with x ≥ 0.56 (AFM2) accompanying a structural transition from tetragonal to orthorhombic. Surprisingly, the Fe magnetic moment in AFM2 reaches a magnitude of 2.73 μ B /Fe, which is the largest in all nondoped iron pnictides and chalcogenides. Theoretical calculations suggest that the AFM2 phase originates in kinetic frustration of the Fe-3 d xy orbital, in which the nearest-neighbor hopping parameter becomes zero. The unique phase diagram, i.e., highest- T c superconducting phase adjacent to the strongly correlated phase in electron-overdoped regime, yields important clues to the unconventional origins of superconductivity.

Fermentation pH Modulates the Size Distributions and Functional Properties of Gluconobacter albidus TMW 2.1191 Levan

PubMed Central

Ua-Arak, Tharalinee; Jakob, Frank; Vogel, Rudi F.

2017-01-01

Bacterial levan has gained an increasing interest over the last decades due to its unique characteristics and multiple possible applications. Levan and other exopolysaccharides (EPSs) production are usually optimized to obtain the highest concentration or yield while a possible change of the molecular size and mass during the production process is mostly neglected. In this study, the molar mass and radius of levan samples were monitored during fermentations with the food-grade, levan-producing acetic acid bacterium Gluconobacter (G.) albidus TMW 2.1191 in shake flasks (without pH control) and bioreactors (with pH control at 4.5, 5.5 and 6.5, respectively). In uncontrolled fermentations, the levan size/molar mass continuously decreased concomitantly with the continuous acidification of the nutrient medium. On the contrary, the amount, molar mass and size of levan could be directly influenced by controlling the pH during fermentation. Using equal initial substrate amounts, the largest weight average molar mass and geometric radius of levan were observed at constant pH 6.5, while the highest levan concentration was obtained at constant pH 4.5. Since there is a special demand to find suitable hydrocolloids from food-grade bacteria to develop novel gluten-free (GF) products, these differently produced levans were used for baking of GF breads, and the best quality improvement was obtained by addition of levan with the highest mass and radius. This work, therefore, demonstrates for the first time that one bacterial strain can produce specific high molecular weight fractions of one EPS type, which differ in properties and sizes among each other in dependence of the controllable production conditions. PMID:28522999

Lactation curves of dairy camels in an intensive system.

PubMed

Musaad, Abdelgadir; Faye, Bernard; Nikhela, Abdelmoneim Abu

2013-04-01

Weekly milk records of 47 she-camels in a multibreed dairy camel herd were collected for over a period of 5 years. A total of 72 lactation curves were defined, and relationships with parity, calving season, lactation length, milk production level, following lactations, and dam weight were analyzed. Overall mean values were milk yield up to 12 months, 1,970 ± 790 l; lactation length, 12.5 months; persistency, 94.7 %; weekly peak yield, 50.7 l; monthly peak yield, 220 ± 90 l; and the number of weeks to reach peak yield, 28. The highest productivity was recorded in summer with a weekly mean of 48.2 ± 19.4 l, compared with 34.1 ± 16.3 l in winter. The highest average yield recorded was for camels at sixth parity, whereas the highest weekly peak was at eighth parity, and highest persistency at fifth parity. Camels that calved during the cold months (November to February) were most productives, with the highest persistency, peak yield, and longest lactation length. Four types of curves were identified corresponding to different parities and milk yield levels. Based on these data, specific models for camels are proposed.

Significance of Herbaspirillum seropedicae inoculation and/or straw amendment on growth and dinitrogen fixation of wheat using 15N-dilution method.

PubMed

el-Komy, H M; Saad, O A; Hetta, A M

2003-01-01

The effect of Herbaspirillum seropedicae inoculation and/or maize straw (0, 5 and 10 Mg/hm2) amendment on the growth and N2 fixation of wheat was determined in pot experiments using 15N-dilution method. Inoculation resulted in accumulation of fixed nitrogen, and % N from atmosphere being 24.6 and 26.5% in wheat shoot and grain, respectively. Straw amendment reduced % Natm to 16.1 and 20.2% at high straw level (10 Mg/hm2). Rational nitrogen fertilization (180 kg N/hm2) completely inhibited N2 fixation by H. seropedicae inoculation. Bacterial inoculation increased dry shoot and grain yield up to 23 and 31%, respectively. The highest levels of shoot and grain dry mass (46.5 and 42.4%) were obtained by N-fertilization in both inoculated and uninoculated plants. Total shoot and grain N-yield increased irrespective of organic matter amendment by inoculation up to 9 and 25%, respectively. N-fertilized plants recorded a maximum increase in N-yield (57 and 51%). H. seropedicae was reisolated from inoculated wheat histosphere after harvesting (90 d from sowing). Neither organic matter nor mineral nitrogen applications had any marked effect on bacterial total counts colonizing wheat histosphere. Moreover, no symptoms of mottled stripe disease were observed on leaves and stems of inoculated plants.

Ridge sowing of sunflower (Helianthus annuus L.) in a minimum till system improves the productivity, oil quality, and profitability on a sandy loam soil under an arid climate.

PubMed

Sher, Ahmad; Suleman, Muhammad; Qayyum, Abdul; Sattar, Abdul; Wasaya, Allah; Ijaz, Muhammad; Nawaz, Ahmad

2018-04-01

Sunflower (Helianthus annuus L.) is a major oilseed crop grown for its edible oil across the globe including Pakistan. In Pakistan, the production of edible oil is less than the required quantity; the situation is being worsened with the increasing population. Thus, there is dire need to grow those sunflower genotypes which perform better under a given set of agronomic practices. In this 2-year study, we compared four sunflower genotypes, viz., Armoni, Kundi, Sinji, and S-278 for their yield potential, oil contents, fatty acid composition, and profitability under three sowing methods, viz., bed sowing, line sowing, and ridge sowing and two tillage system, viz., plow till and minimum till. Among the sunflower genotypes, the genotype Armoni produced the highest plant height, number of leaves, head diameter, 1000-achene weight, and achene yield; the oil contents and oleic acid were the highest in genotype Sinji. Among the sowing methods, the highest number of leaves per plant, head diameter, number of achenes per head, achene yield, and oil contents were recorded in ridge sowing. Among the tillage systems, the highest head diameter 16. 2 cm, 1000-achene weight (57.2 g), achene yield (1.8 t ha -1 ), oil contents (35.2%), and oleic acid (15.2%) were recorded in minimum till sunflower. The highest net benefits and benefit to cost ratio were recorded in minimum till ridge sown Armoni genotype. In conclusion, the genotype Armoni should be grown on ridges to achieve the highest achene yield, oil contents, and net profitability.

Effect of copper oxide concentration on the formation and persistency of environmentally persistent free radicals (EPFRs) in particulates.

PubMed

Kiruri, Lucy W; Khachatryan, Lavrent; Dellinger, Barry; Lomnicki, Slawo

2014-02-18

Environmentally persistent free radicals (EPFRs) are formed by the chemisorption of substituted aromatics on metal oxide surfaces in both combustion sources and superfund sites. The current study reports the dependency of EPFR yields and their persistency on metal loading in particles (0.25, 0.5, 0.75, 1, 2, and 5% CuO/silica). The EPFRs were generated through exposure of particles to three adsorbate vapors at 230 °C: phenol, 2-monochlorophenol (2-MCP), and dichlorobenzene (DCBz). Adsorption resulted in the formation of surface-bound phenoxyl- and semiquinoine-type radicals with characteristic EPR spectra displaying a g value ranging from ∼ 2.0037 to 2.006. The highest EPFR yield was observed for CuO concentrations between 1 and 3% in relation to MCP and phenol adsorption. However, radical density, which is expressed as the number of radicals per copper atom, was highest at 0.75-1% CuO loading. For 1,2-dichlorobenzene adsorption, radical concentration increased linearly with decreasing copper content. At the same time, a qualitative change in the radicals formed was observed--from semiquinone to chlorophenoxyl radicals. The two longest lifetimes, 25 and 23 h, were observed for phenoxyl-type radicals on 0.5% CuO and chlorophenoxyl-type radicals on 0.75% CuO, respectively.

Current lipid extraction methods are significantly enhanced adding a water treatment step in Chlorella protothecoides.

PubMed

Ren, Xiaojie; Zhao, Xinhe; Turcotte, François; Deschênes, Jean-Sébastien; Tremblay, Réjean; Jolicoeur, Mario

2017-02-11

Microalgae have the potential to rapidly accumulate lipids of high interest for the food, cosmetics, pharmaceutical and energy (e.g. biodiesel) industries. However, current lipid extraction methods show efficiency limitation and until now, extraction protocols have not been fully optimized for specific lipid compounds. The present study thus presents a novel lipid extraction method, consisting in the addition of a water treatment of biomass between the two-stage solvent extraction steps of current extraction methods. The resulting modified method not only enhances lipid extraction efficiency, but also yields a higher triacylglycerols (TAG) ratio, which is highly desirable for biodiesel production. Modification of four existing methods using acetone, chloroform/methanol (Chl/Met), chloroform/methanol/H 2 O (Chl/Met/H 2 O) and dichloromethane/methanol (Dic/Met) showed respective lipid extraction yield enhancement of 72.3, 35.8, 60.3 and 60.9%. The modified acetone method resulted in the highest extraction yield, with 68.9 ± 0.2% DW total lipids. Extraction of TAG was particularly improved with the water treatment, especially for the Chl/Met/H 2 O and Dic/Met methods. The acetone method with the water treatment led to the highest extraction level of TAG with 73.7 ± 7.3 µg/mg DW, which is 130.8 ± 10.6% higher than the maximum value obtained for the four classical methods (31.9 ± 4.6 µg/mg DW). Interestingly, the water treatment preferentially improved the extraction of intracellular fractions, i.e. TAG, sterols, and free fatty acids, compared to the lipid fractions of the cell membranes, which are constituted of phospholipids (PL), acetone mobile polar lipids and hydrocarbons. Finally, from the 32 fatty acids analyzed for both neutral lipids (NL) and polar lipids (PL) fractions, it is clear that the water treatment greatly improves NL-to-PL ratio for the four standard methods assessed. Water treatment of biomass after the first solvent extraction step helps the subsequent release of intracellular lipids in the second extraction step, thus improving the global lipids extraction yield. In addition, the water treatment positively modifies the intracellular lipid class ratios of the final extract, in which TAG ratio is significantly increased without changes in the fatty acids composition. The novel method thus provides an efficient way to improve lipid extraction yield of existing methods, as well as selectively favoring TAG, a lipid of the upmost interest for biodiesel production.

Production of Sterilizing Agents from Calendula officinalis Extracts Optimized by Response Surface Methodology

PubMed Central

Goktas, Fatih Mehmet; Sahin, Bilgesu; Yigitarslan, Sibel

2015-01-01

The aim of this study was to produce hand sterilizing liquid and wet wipes with the extracts of Calendula officinalis. Since this plant has well known antimicrobial activity due to its phytochemical constituents, the increase in the extraction yield was chosen as the principle part of the production process. To achieve the maximum yield, parameters of solid-to-liquid ratio, extraction temperature, and time were studied. The optimum conditions were determined by response surface methodology as 41°C, 7 h, and 3.3 g/200 mL for temperature, time, and solid-to-liquid ratio, respectively. The yield achieved at those conditions was found to be 90 percent. The highest amounts of flavonoids were detected at optimum, whereas the highest triterpene and saponin constituents were determined at different design points. The microbial efficiencies of extracts were determined by the inhibition of the growth of selected microorganisms. Different dilution rates and interaction times were used as parameters of inhibition. Not any of the constituent but symbiotic relation in-between reached the highest inhibition of 90 percent. The pH values of the extracts were 5.1 to 5.4. As a result, the extraction of Calendula officinalis at the optimum conditions can be used effectively in the production of wet wipes and hand sterilizing liquid. PMID:26064122

Biogas production from anaerobic codigestion of cowdung and elephant grass (Pennisetum Purpureum) using batch digester

NASA Astrophysics Data System (ADS)

Haryanto, Agus; Hasanudin, Udin; Afrian, Chandra; Zulkarnaen, Iskandar

2018-03-01

This study aimed at determining biogas production from codigestion of Elephant grass and cowdung using batch digester. Fresh grass was manually chopped with a maximum length of 3 cm. Chopped grass (25 kg) was perfectly mixed with fresh cowdung (25 kg). The mixture was introduced into a 220-liter batch drum digester. The substrate was diluted with water at different rates (P1 = 50 L, P2 = 75 L, and P3 = 100 L) and was stirred thoroughly. Six digesters were prepared as duplicate for each treatment. Two other digesters containing only 25 kg cowdung diluted with 25 L water were also provided as control treatment (P0). The digesters were air tightly sealed for 70 days. Observation was conducted on daily temperature, substrate pH (initial and final), TS and VS content, biogas yield and biogas composition. Results showed that final pH of grass containing substrate was in the acidic range, namely 4.50, 4.62, 6.82, whereas that of control (P0) was normal with pH of 7.30. Digester with substrate composition 25:25:100 (cowdung:grass:water) produced the highest biogas total (524.3 L). Biogas yield of codigestion, however, was much lower as compared to that of control, namely 7.35, 16.75, and 111.72 L/kg VS r respectively for treatment P1, P2, P3. with dilution rate of 50, 75, and 100 L. Biogas produced from control digester had methane content of 53.88%. In contrast, biogas resulted from all treatments contained low methane (the highest was 31.37%). Methane yield of 39.3 L/kg TS removal was achieved from digester with dilution 100 L (P3). Mechanical pretreatment is suggested to break Elephant grass down into smaller particles prior to introducing it into the digestion process.

Yield of Echocardiogram and Predictors of Positive Yield in Pediatric Patients: A Study in an Urban, Community-Based Outpatient Pediatric Cardiology Clinic.

PubMed

Billa, Ramya Deepthi; Szpunar, Susan; Zeinali, Lida; Anne, Premchand

2018-01-01

The yield of outpatient echocardiograms varies based on the indication for the echocardiogram and the age of the patient. The purpose of this study was to determine the cumulative yield of outpatient echocardiograms by age group and reason for the test. A secondary aim was to determine the predictors of a positive echocardiogram in an outpatient cardiology clinic at a large community teaching hospital. We retrospectively reviewed the charts of 891 patients who had a first-time echocardiogram between 2011 and 2015. Positive yield was defined as echocardiographic findings that explained the reason for the echocardiogram. The overall positive yield was 8.2%. Children between birth and 3 months of age had the highest yield (34.2%), and children between 12 and 18 years of age had the lowest yield (1%). Patients with murmurs (18.1%) had the highest yield compared with patients with other signs or symptoms. By age group and reason, the highest yields were as follows: 0 to 3 months of age, murmur (39.2%); 4 to 11 months of age, >1 symptom (50%); and 1 to 5 years of age, shortness of breath (66.7%). Based on our study, the overall yield of echocardiograms in the outpatient pediatric setting is low. Age and symptoms should be considered before ordering an echocardiogram.

Isolation of endophytic fungi from Dioscorea zingiberensis C. H. Wright and application for diosgenin production by solid-state fermentation.

PubMed

Xiang, Haibo; Zhang, Tao; Pang, Xu; Wei, Yuzhen; Liu, Hongyu; Zhang, Yuqin; Ma, Baiping; Yu, Liyan

2018-05-03

In this study, endophytic fungi were isolated from Dioscorea zingiberensis C.H. Wright (DZW), and a novel clean process to prepare diosgenin from DZW was developed. A total of 123 strains of endophytic fungi were isolated from different plant tissues of DZW. Among them, the strain Fusarium sp. (CPCC 400709) showed the best activity of hydrolyzing steroidal saponins in DZW into diosgenin. Thus, this strain was used to prepare diosgenin from DZW by solid-state fermentation. The fermentation parameters were optimized using response surface methodology, and a high yield of diosgenin (2.16%) was obtained at 14.5% ammonium sulfate, an inoculum size of 12.3%, and 22 days of fermentation. Furthermore, the highest diosgenin yield (2.79%) was obtained by co-fermentation with Fusarium sp. (CPCC 400709) and Curvularia lunata (CPCC 400737), which was 98.9% of that obtained by β-glucosidase pretreated acid hydrolysis (2.82%). This process is acid-free and wastewater-free, and shows promise as an effective and clean way to prepare diosgenin for use in industrial applications from DZW.

Ethanol production from a biomass mixture of furfural residues with green liquor-peroxide saccarified cassava liquid.

PubMed

Ji, Li; Zheng, Tianran; Zhao, Pengxiang; Zhang, Weiming; Jiang, Jianxin

2016-06-01

As the most abundant renewable resources, lignocellulosic materials are ideal candidates as alternative feedstock for bioethanol production. Cassava residues (CR) are byproducts of the cassava starch industry which can be mixed with lignocellulosic materials for ethanol production. The presence of lignin in lignocellulosic substrates can inhibit saccharification by reducing the cellulase activity. Simultaneous saccharification and fermentation (SSF) of furfural residues (FR) pretreated with green liquor and hydrogen peroxide (GL-H2O2) with CR saccharification liquid was investigated. The final ethanol concentration, yield, initial rate, number of live yeast cells, and the dead yeast ratio were compared to evaluate the effectiveness of combining delignificated lignocellulosic substrates and starchy substrates for ethanol production. Our results indicate that 42.0 % of FR lignin removal was achieved on FR using of 0.06 g H2O2/g-substrate and 9 mL GL/g-substrate at 80 °C. The highest overall ethanol yield was 93.6 % of the theoretical. When the ratio of 0.06 g/g-H2O2-GL-pretreated FR to CR was 5:1, the ethanol concentration was the same with that ratio of untreated FR to CR of 1:1. Using 0.06 g/g-H2O2-GL-pretreated FR with CR at a ratio of 2:1 resulted in 51.9 g/L ethanol concentration. Moreover, FR pretreated with GL-H2O2 decreased the concentration of byproducts in SSF compared with that obtained in the previous study. The lignin in FR would inhibit enzyme activity and GL-H2O2 is an advantageous pretreatment method to treat FR and high intensity of FR pretreatment increased the final ethanol concentration. The efficiency of ethanol fermentation of was improved when delignification increased. GL-H2O2 is an advantageous pretreatment method to treat FR. As the pretreatment dosage of GL-H2O2 on FR increased, the proportion of lignocellulosic substrates was enhanced in the SSF of the substrate mixture of CR and FR as compared with untreated FR. Moreover, the final ethanol concentration was increased with a high ethanol yield and lower byproduct concentrations.

Increase of protein extraction yield from rapeseed meal through a pretreatment with phytase.

PubMed

Rodrigues, Ivo M; Carvalho, M Graça Vs; Rocha, Jorge Ms

2017-06-01

Rapeseed meal is a good source of high-quality vegetal protein but contains antinutritional compounds that limit its use for human and animal feed. The aim of this study was to develop a methodology to enhance alkaline protein extraction of rapeseed meal and to produce protein-rich products with low levels of phytic acid. Different phytase dosages and operating conditions were used for rapeseed meal pretreatment followed by alkaline extraction at different temperatures, time, pH and solid/liquid ratios (S/L). The highest protein extraction yield attained was 72.1%, for 2 h at 55 °C, with a phytase dosage of 0.8 U g -1 when the alkaline extraction was performed at 75 °C, pH 12.5 and 60 min for an S/L ratio of 10 g 100 mL -1 water. The extraction yields were higher than those previously obtained without enzymatic pretreatment. Phytase pretreatment enhanced alkaline extraction yield of proteins from rapeseed meal. This procedure allowed also the production of rapeseed protein concentrates with very low levels of phytic acid, ∼1 g kg -1 , improving their nutritional properties and commercial value. Moreover, after the pretreatment, the amount of phytic acid in the remaining rapeseed meal decreases about 25%. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Photo-induced CO2 reduction by CH4/H2O to fuels over Cu-modified g-C3N4 nanorods under simulated solar energy

NASA Astrophysics Data System (ADS)

Tahir, Beenish; Tahir, Muhammad; Amin, Nor Aishah Saidina

2017-10-01

Copper modified polymeric graphitic carbon nitride (Cu/g-C3N4) nanorods for photo-induced CO2 conversion with methane (CH4) and water (H2O) as reducing system under simulated solar energy has been investigated. The nanocatalysts, synthesized by pyrolysis and sonication, were characterized by XRD, FTIR, Raman analysis, XPS, SEM, N2 adsorption-desorption and PL spectroscopy. The presence of Cu2+ ions over the g-C3N4 structure inhibited charge carriers recombination process. The results indicated that photo-activity and selectivity of Cu/g-C3N4 photo-catalyst for CO2 reduction greatly dependent on the type of CO2-reduction system. CO2 was efficiently converted to CH4 and CH3OH with traces of C2H4 and C2H6 hydrocarbons in the CO2-water system. The yield of the main product, CH4 over 3 wt.% Cu/g-C3N4 was 109 μmole g-cata.-1 h-1 under visible light irradiation, significantly higher than the pure g-C3N4 catalyst (60 μmole/g.cat). In photo-induced CO2-CH4 reaction, CO and H2 were detected as the main products with smaller amount of hydrocarbons. The highest efficiency was detected over 3 wt.%Cu-loading of g-C3N4 and at optimal CH4/CO2 feed ratio of 1.0. The maximum yield of CO and H2 detected were 142 and 76 μmole g-catal.-1 h-1, respectively at selectivity 66.6% and 32.5%, respectively. Significantly enhanced CO2/CH4 reduction over Cu/g-C3N4 was attributed to its polymeric structure with efficient charge transfer property and inhibited charges recombination rate. A proposed photo-induced reaction mechanism, corroborated with the experimental data, was also deliberated.

A series of inorganic solid nitrogen sources for the synthesis of metal nitride clusterfullerenes: the dependence of production yield on the oxidation state of nitrogen and counter ion.

PubMed

Liu, Fupin; Guan, Jian; Wei, Tao; Wang, Song; Jiao, Mingzhi; Yang, Shangfeng

2013-04-01

A series of nitrogen-containing inorganic solid compounds with variable oxidation states of nitrogen and counter ions have been successfully applied as new inorganic solid nitrogen sources toward the synthesis of Sc-based metal nitride clusterfullerenes (Sc-NCFs), including ammonium salts [(NH4)xH(3-x)PO4 (x = 0-2), (NH4)2SO4, (NH4)2CO3, NH4X (X = F, Cl), NH4SCN], thiocyanate (KSCN), nitrates (Cu(NO3)2, NaNO3), and nitrite (NaNO2). Among them, ammonium phosphates ((NH4)xH(3-x)PO4, x = 1-3) and ammonium thiocyanate (NH4SCN) are revealed to behave as better nitrogen sources than others, and the highest yield of Sc-NCFs is achieved when NH4SCN was used as a nitrogen source. The optimum molar ratio of Sc2O3:(NH4)3PO4·3H2O:C and Sc2O3:NH4SCN:C has been determined to be 1:2:15 and 1:3:15, respectively. The thermal decomposition products of these 12 inorganic compounds have been discussed in order to understand their different performances toward the synthesis of Sc-NCFs, and accordingly the dependence of the production yield of Sc-NCFs on the oxidation state of nitrogen and counter ion is interpreted. The yield of Sc3N@C80 (I(h) + D(5h)) per gram Sc2O3 by using the N2-based group of nitrogen sources (thiocyanate, nitrates, and nitrite) is overall much lower than those by using gaseous N2 and NH4SCN, indicating the strong dependence of the yield of Sc-NCFs on the oxidation state of nitrogen, which is attributed to the "in-situ" redox reaction taking place for the N2-based group of nitrogen sources during discharging. For NH3-based group of nitrogen sources (ammonium salts) which exhibits a (-3) oxidation states of nitrogen, their performance as nitrogen sources is found to be sensitively dependent on the anion, and this is understood by considering their difference on the thermal stability and/or decomposition rate. Contrarily, for the N2-based group of nitrogen sources, the formation of Sc-NCFs is independent to both the oxidation state of nitrogen (+3 or +5) and the cation.

Simultaneous removal of 2,4,6-tribromophenol from water and bromate ion minimization by ozonation.

PubMed

Gounden, Asogan N; Singh, Sooboo; Jonnalagadda, Sreekantha B

2018-06-02

The study investigates the degradation of 2,4,6-tribromophenol (2,4,6-TBP) and the influence of solution pH, alkalinity, H 2 O 2 and O 3 dosage. Debromination efficiency of 2,4,6-TBP was the highest in basic water (pH = 10.61). The extent of TOC removal compared favourably with the amount of substrate converted, suggesting favourable mineralization of oxygenated by-products (OBPs). Ozonation in basic water favoured the formation of toxicBrO 3 - , while in acidic water (pH = 2.27) BrO 3 - yield was lowest. In acidic water the presence of CO 3 2- showed negligible effect on conversion, TOC and  BrO 3 - yield compared to ozonation alone. In basic water both 2,4,6-TBP conversion and TOC removal decreased with an increase in CO 3 2- , hence minimizing BrO 3 - formation. The O 3 /H 2 O 2 process showed an improvement in the debromination efficiency and TOC data revealed that total mineralization of OBP's was achieved. However, only 10% H 2 O 2 was able to effectively decrease BrO 3 - formation. Increasing the ozone concentration from 20 to 100 ppm enhanced the conversion of 2,4,6-TBP and TOC removal. At low ozone concentrations poor mineralization of OBP's occurred, while complete mineralization was achieved at higher ozone dose. The reaction pathways for ozone degradation of 2,4,6-TBP in acidic and basic waters is proposed. Copyright © 2018 Elsevier B.V. All rights reserved.

Evaluation of process performance, energy consumption and microbiota characterization in a ceramic membrane bioreactor for ex-situ biomethanation of H2 and CO2.

PubMed

Alfaro, Natalia; Fdz-Polanco, María; Fdz-Polanco, Fernando; Díaz, Israel

2018-06-01

The performance of a pilot ceramic membrane bioreactor for the bioconversion of H 2 and CO 2 to bioCH 4 was evaluated in thermophilic conditions. The loading rate was between 10 and 30 m 3  H 2 /m 3 reactor  d and the system transformed 95% of H 2 fed. The highest methane yield found was 0.22 m 3  CH 4 /m 3  H 2 , close to the maximum stoichiometric value (0.25 m 3  CH 4 /m 3  H 2 ) thus indicating that archaeas employed almost all H 2 transferred to produce CH 4 . k L a value of 268 h -1 was reached at 30 m 3  H 2 /m 3 reactor  d. DGGE and FISH revealed a remarkable archaeas increase related to the selection-effect of H 2 on community composition over time. Methanothermobacter thermautotrophicus was the archaea found with high level of similarity. This study verified the successful application of membrane technology to efficiently transfer H 2 from gas to the liquid phase, the development of a hydrogenotrophic community from a conventional thermophilic sludge and the technical feasibility of the bioconversion. Copyright © 2018 Elsevier Ltd. All rights reserved.

Hydrogen and polyhydroxybutyrate producing abilities of microbes from diverse habitats by dark fermentative process.

PubMed

Porwal, Shalini; Kumar, Tarika; Lal, Sadhana; Rani, Asha; Kumar, Sushil; Cheema, Simrita; Purohit, Hemant J; Sharma, Rakesh; Singh Patel, Sanjay Kumar; Kalia, Vipin Chandra

2008-09-01

Thirty five bacterial isolates from diverse environmental sources such as contaminated food, nitrogen rich soil, activated sludges from pesticide and oil refineries effluent treatment plants were found to belong to Bacillus, Bordetella, Enterobacter, Proteus, and Pseudomonas sp. on the basis of 16S rRNA gene sequence analysis. Under dark fermentative conditions, maximum hydrogen (H(2)) yields (mol/mol of glucose added) were recorded to be 0.68 with Enterobacter aerogenes EGU16 followed by 0.63 with Bacillus cereus EGU43 and Bacillus thuringiensis EGU45. H(2) constituted 63-69% of the total biogas evolved. Out of these 35 microbes, 18 isolates had the ability to produce polyhydroxybutyrate (PHB), which varied up to 500 mg/l of medium, equivalent to a yield of 66.6%. The highest PHB yield was recorded with B. cereus strain EGU3. Nine strains had high hydrolytic activities (zone of hydrolysis): lipase (34-38 mm) -Bacillus sphaericus strains EGU385, EGU399 and EGU542; protease (56-62 mm) -Bacillus sp. strains EGU444, EGU447 and EGU445; amylase (23 mm) -B. thuringiensis EGU378, marine bacterium strain EGU409 and Pseudomonas sp. strain EGU448. These strains with high hydrolytic activities had relatively low H(2) producing abilities in the range of 0.26-0.42 mol/mol of glucose added and only B. thuringiensis strain EGU378 had the ability to produce PHB. This is the first report among the non-photosynthetic microbes, where the same organism(s) -B. cereus strain EGU43 and B. thuringiensis strain EGU45, have been shown to produce H(2) - 0.63 mol/mol of glucose added and PHB - 420-435 mg/l medium.

Lactic acid fermentation from food waste with indigenous microbiota: Effects of pH, temperature and high OLR.

PubMed

Tang, Jialing; Wang, Xiaochang; Hu, Yisong; Zhang, Yongmei; Li, Yuyou

2016-06-01

The effects of pH, temperature and high organic loading rate (OLR) on lactic acid production from food waste without extra inoculum addition were investigated in this study. Using batch experiments, the results showed that although the hydrolysis rate increased with pH adjustment, the lactic acid concentration and productivity were highest at pH 6. High temperatures were suitable for solubilization but seriously restricted the acidification processes. The highest lactic acid yield (0.46g/g-TS) and productivity (278.1mg/Lh) were obtained at 37°C and pH 6. In addition, the lactic acid concentration gradually increased with the increase in OLR, and the semi-continuous reactor could be stably operated at an OLR of 18g-TS/Ld. However, system instability, low lactic acid yield and a decrease in VS removal were noticed at high OLRs (22g-TS/Ld). The concentrations of volatile fatty acids (VFAs) in the fermentation mixture were relatively low but slightly increased with OLR, and acetate was the predominant VFA component. Using high-throughput pyrosequencing, Lactobacillus from the raw food waste was found to selectively accumulate and become dominant in the semi-continuous reactor. Copyright © 2016 Elsevier Ltd. All rights reserved.

Isolation, Fractionation and Characterization of Catalase from Neurospora crassa (InaCC F226)

NASA Astrophysics Data System (ADS)

Suryani; Ambarsari, L.; Lindawati, E.

2017-03-01

Catalase from Indigenous isolate Neurospora crassa InaCC F226 has been isolated, fractionated and characterized. Production of catalase by Neurospora crassa was done by using PDA medium (Potato Dextrosa Agar) and fractionated with ammonium sulphate with 20-80% saturation. Fraction 60% was optimum saturation of ammonium sulphate and had highest specific activity 3339.82 U/mg with purity 6.09 times, total protein 0.920 mg and yield 88.57%. The optimum pH and temperature for catalase activity were at 40°C and pH 7.0, respectively. The metal ions that stimulated catalase activity acted were Ca2+, Mn2+ and Zn2+, and inhibitors were EDTA, Mg2+ and Cu2+. Based on Km and Vmax values were 0.2384 mM and 13.3156 s/mM.

Synthesis of K2O/Zeolite catalysts by KOH impregnation for biodiesel production from waste frying oil

NASA Astrophysics Data System (ADS)

Fitriana, N.; Husin, H.; Yanti, D.; Pontas, K.; Alam, P. N.; Ridho, M.; Iskandar

2018-03-01

K2O/Zeolite compounds were successfully synthesized using KOH as starting material and natural zeolite as support. The catalysts were calcined at 500°C for 3 h and then characterized by X-Ray Diffractometer (XRD) and Scanning Electron Microscopy (SEM). The SEM images reveal that the zeolite and K2O/zeolite particles are irregular in shape (100 to 400 nm). The independent variables were impregnated amounts of KOH (15 - 25%), catalyst to oil ratios of 1.0 - 6.0 wt.%, and reaction time of 2 h. The highest biodiesel yield of 95% was produced from the reaction with 2.1 wt.% catalyst of 25% KOH impregnated. The properties of produced biodiesel complied with SNI. The catalytic stability test showed that the 25% KOH impregnated catalyst was stable.

Effect of human gonadotropins on spermiation and androgen biosynthesis in the testis of the toad Bufo arenarum (Amphibia, Anura).

PubMed

Pozzi, Andrea Gabriela; Rosemblit, Cinthia; Ceballos, Nora Raquel

2006-01-01

This paper analyzes, in the toad Bufo arenarum, the effect on spermiation and androgen secretion of two human recombinant gonadotropins, human recombinant LH (hrLH) and human recombinant FSH (hrFSH) as well as the well-known spermiation-inducing hormone, human chorionic gonadotropin (hCG). For this purpose, testes were incubated with different concentrations of hrLH (0.01-2.5 microg/ml) and hrFSH (0.05-5 microg/ml), and results were compared with those obtained with 2.5 microg/ml hCG. Spermiation was most efficiently stimulated by hrFSH, which elicited a higher response than either hrLH or hCG. Both hrFSH and hrLH produced a bell-shaped dose-response curve, with a 50% inhibition on spermiation at a concentration twice higher than that necessary to get the highest response. However, none of the gonadotropins yielded a biphasic response on androgen secretion, hrLH producing the highest response at a concentration that evoked a 70% inhibition in the spermiation test. Regarding steroidogenesis, hrLH and hrFSH were more active than hCG. Taken together, the results described in this paper suggest that, in B. arenarum, spermiation and androgen secretion are mediated by different receptors. After comparing the effects of recombinant hormones, we conclude that hrFSH has a greater effect on spermiation than hCG or hrLH.

Sedimentary Catalysis of Radiolytic Hydrogen Production - A Global Perspective

NASA Astrophysics Data System (ADS)

Sauvage, J.; Spivack, A. J.; Smith, D. C.; Anderson, C. H.; Murray, R. W.; D'Hondt, S.

2016-12-01

Constraining rates of various energy- producing metabolic reactions is central to our understanding of subsurface microbial ecosystems. Radiolytic hydrogen (H2), produced by the radioactive splitting of water due to the natural decay of elements in the sediment, has been proposed to be a significant electron donor in sediment of oligothrophic oceanic regions. However accurate constraints of in situ production rates are required to test this hypothesis. We experimentally quantified radiolytic H2 yields (H2 produced per unit of absorbed energy in solution) due to γ radiation (Cs-137) and α radiation (Po-210) in marine sediment by exposing seawater slurries of sediment to radiation and measuring the production of H2. We selected 28 samples from different ocean basins and depositional environments aiming to capture the range of representative lithologies found across the global ocean. These experiments demonstrate that marine sediment greatly amplifies the production of radiolytic H2 production compared to pure water, with seawater-saturated abyssal clay exhibiting the highest yield. South Pacific Gyre [SPG], North Atlantic [NA] and North Pacific Gyre [NPG] abyssal clays amplify H2 production by factors of 13, 16 and 33, respectively. Calcareous ooze amplifies radiolytic H2 production by an average factor of 5. Despite continual production, dissolved H2 concentrations are generally below detection in oxic subseafloor sediment of the SPG, NPG and NA. This suggests that the aerobic H2 oxidation rate (Knallgas reaction) is essentially equal to its production rate in these environments. We assess the relative importance of buried organic matter and radiolytic H2 in terms of electron donor availability by comparing rates of radiolytic H2 production to rates of net O2 respiration (inferred to equal rates of organic oxidation). For NA, SPG and NPG abyssal clay older than a few million years, radiolytic H2 production rates are respectively factors of 20, 30 and 49 higher than rates of organic-fueled respiration rates. Extrapolating these results, we infer that radiolytic H2 is likely to be the predominant electron donor for subseafloor sedimentary communities throughout 37% of the global ocean.

Starbon/High-Amylose Corn Starch-Supported N-Heterocyclic Carbene-Iron(III) Catalyst for Conversion of Fructose into 5-Hydroxymethylfurfural.

PubMed

Matharu, Avtar S; Ahmed, Suleiman; Almonthery, Badriya; Macquarrie, Duncan J; Lee, Yoon-Sik; Kim, Yohan

2018-02-22

Iron-N-heterocyclic carbene complexes (Fe-NHCs) have come to prominence because of their applicability in diverse catalytic reactions, ranging from C-C cross-coupling and C-X bond formation to substitution, reduction, polymerization, and dehydration reactions. The detailed synthesis, characterization, and application of novel heterogeneous Fe-NHC catalysts immobilized on mesoporous expanded high-amylose corn starch (HACS) and Starbon 350 (S350) for facile fructose conversion into 5-hydroxymethylfurfural (HMF) is reported. Both catalyst types showed good performance for the dehydration of fructose to HMF when the reaction was tested at 100 °C with varying time (10 min, 20 min, 0.5 h, 1 h, 3 h and 6 h). For Fe-NHC/S350, the highest HMF yield was 81.7 % (t=0.5 h), with a TOF of 169 h -1 , fructose conversion of 95 %, and HMF selectivity of 85.7 %, whereas for Fe-NHC/expanded HACS, the highest yield was 86 % (t=0.5 h), with a TOF of 206 h -1 , fructose conversion of 87 %, and HMF selectivity of 99 %. Iron loadings of 0.26 and 0.30 mmol g -1 were achieved for Fe-NHC/expanded starch and Fe-NHC/S350, respectively. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Screening of liquid media and fermentation of an endophytic Beauveria bassiana strain in a bioreactor

PubMed Central

2014-01-01

A novel approach for biological control of insect pests could be the use of the endophytic entomopathogenic Beauveria bassiana isolate ATP-02. For the utilization of the endophyte as a commercial biocontrol agent, the fungus has to be mass-produced. B. bassiana was raised in shake flask cultures to produce high concentrations of total spores (TS), which include blastospores (BS) and submerged conidiospores (SCS). The highest concentration of 1.33×109 TS/mL and the highest yield of 5.32×1010 TS/g sucrose was obtained in the TKI broth with 5% sugar beet molasses which consists of 50% sucrose as a carbon source. In spite of the lower sugar concentration (2.5%) the amount of TS could be increased up to 11-times in contrast to the cultivation with 5% sucrose. The scale-up to a 2 L stirred tank reactor was carried out at 25°C, 200–600 rpm and 1 vvm at pH 5.5. A TS yield of 5.2×1010 TS/g sucrose corresponding to a SCS yield of 0.2×1010 SCS/g sucrose was obtained after 216 h. With regards to the culture medium the cost of 1012 TS amounts to 0.24 €. Plutella xylostella larvae, which were fed with oilseed rape leaves treated with spores from fermentation resulted in 77 ± 5% mortality. Moreover, spores from submerged cultivation were able to colonize oilseed rape leaves via leaf application. This is the first report of fermentation of an endophytic B. bassiana strain in a low-cost culture medium to very high yields of TS. PMID:24949278

Purification and Properties of a New L-Sorbose Dehydrogenase Accelerative Protein from Bacillus megaterium Bred by Ion-Beam Implantation

NASA Astrophysics Data System (ADS)

Zhao, Shiguang; Yao, Liming; Su, Caixin; Wang, Tao; Wang, Jun; Tang, Mingli; Yu, Zengliang

2008-06-01

Bacillus megaterium BM302 bred by ion-beam implantation produces L-sorbose dehydrogenase accelerative protein (SAP) to accelerate the activity of L-sorbose dehydrogenase (SDH) of Gluconobacter oxydans in the 2-keto-L-gulonic acid (2KLG) fermentation from L-sorbose by the mixed culture of B. megaterium BM302 and G. oxydans. The SAP purified by three chromatographic steps gave 35-fold purification with a yield of 13% and a specific activity of 5.21 units/mg protein. The molecular weight of the purified SAP was about 58 kDa. The SDH accelerative activity of SAP at pH 7 and 50°C was the highest. Additionally, it retained 60% activity at a pH range of 6.5 ~ 10 and was stable at 20°C ~ 60°C. After 0.32-unit SAP was added to the single cultured G. oxydans strains, the SDH activity was apparently accelerated and the 2KLG yield of GO29, GO112, G0 and GI13 was enhanced 2.1, 3.3, 3.5 and 2.9 folds respectively over that of the strains without the addition of SAP.

Effects of dissolved oxygen concentration on photosynthetic bacteria wastewater treatment: Pollutants removal, cell growth and pigments production.

PubMed

Meng, Fan; Yang, Anqi; Zhang, Guangming; Wang, Hangyao

2017-10-01

Dissolved oxygen (DO) is an important parameter in photosynthetic bacteria (PSB) wastewater treatment. This study set different DO levels and detected the pollutants removal, PSB growth and pigments production. Results showed that DO significantly influenced the performances of PSB wastewater treatment process. The highest COD (93%) and NH 3 -N removal (83%) was achieved under DO of 4-8mg/L, but DO of 2-4mg/L was recommended considering the aeration cost. PSB biomass reached 1645mg/L under DO of 4-8mg/L with satisfying co-enzyme Q10 content. The biomass yield was relatively stable at all DO levels. For bacteriochlorophyll and carotenoids, DO>1mg/L could satisfy their production. On the other hand, DO<0.5mg/L led to the highest dehydrogenase activity. According to the different purposes, the optimal treatment time was different. The most pigments production occurred at 24h; biomass reached peak at 48h; and the optimal time for pollutants removal was 72h. Copyright © 2017 Elsevier Ltd. All rights reserved.

Improved expression of recombinant plant-made hEGF.

PubMed

Thomas, David Rhys; Walmsley, Amanda Maree

2014-11-01

The yield of recombinant hEGF was increased approximately tenfold through a range of optimisations. Further, the recombinant protein was found to have biological activity comparable to commercial hEGF. Human epidermal growth factor (hEGF) is a powerful mitogen that can enhance the healing of a wide range of injuries, including burns, cuts, diabetic ulcers and gastric ulcers. However, despite its clinical value, hEGF is only consistently used for the treatment of chronic diabetic ulcers due to its high cost. In this study, hEGF was transiently expressed in Nicotiana benthamiana plants and targeted to the apoplast, ER and vacuole. Several other approaches were also included in a stepwise fashion to identify the optimal conditions for the expression of recombinant hEGF. Expression was found to be highest in the vacuole, while targeting hEGF to the ER caused a decrease in total soluble protein (TSP). Using a codon optimised sequence was found to increase vacuolar targeted hEGF yield by ~34 %, while it was unable to increase the yield of ER targeted hEGF. The use of the P19 silencing inhibitor was able to further increase expression by over threefold, and using 5-week-old plants significantly increased expression compared to 4- or 6-week-old-plants. The combined effect of these optimisations increased expression tenfold over the initial apoplast targeted construct to an average yield of 6.24 % of TSP. The plant-made hEGF was then shown to be equivalent to commercial E. coli derived hEGF in its ability to promote the proliferation of mouse keratinocytes. This study supports the potential for plants to be used for the commercial production of hEGF, and identifies a potential limitation for the further improvement of recombinant protein yields.

Bioconversion of α-chitin into N-acetyl-glucosamine using chitinases produced by marine-derived Aeromonas caviae isolates.

PubMed

Cardozo, Flávio Augusto; Gonzalez, Juan Miguel; Feitosa, Valker Araujo; Pessoa, Adalberto; Rivera, Irma Nelly Gutierrez

2017-10-27

N-Acetyl-D-glucosamine (GlcNAc) is a monosaccharide with great application potential in the food, cosmetic, pharmaceutical, and biomaterial areas. GlcNAc is currently produced by chemical hydrolysis of chitin, but the current processes are environmentally unfriendly, have low yield and high cost. This study demonstrates the potential to produce GlcNAc from α-chitin using chitinases of ten marine-derived Aeromonas isolates as a sustainable alternative to the current chemical process. The isolates were characterized as Aeromonas caviae by multilocus sequence analysis (MLSA) using six housekeeping genes (gltA, groL, gyrB, metG, ppsA, and recA), not presented the virulence genes verified (alt, act, ast, ahh1, aer, aerA, hlyA, ascV and ascFG), but showed hemolytic activity on blood agar. GlcNAc was produced at 37 °C, pH 5.0, 2% (w/v) colloidal chitin and crude chitinase extracts (0.5 U mL -1 ) by all the isolates with yields from 14 to 85% at 6 h, 17-89% at 12 h and 19-93% after 24 h. The highest yield of GlcNAc was observed by A. caviae CH129 (93%). This study demonstrates one of the most efficient chitin enzymatic hydrolysis procedures and A. caviae isolates with great potential for chitinases expression and GlcNAc production.

Nitrification inhibitors mitigated reactive gaseous nitrogen intensity in intensive vegetable soils from China.

PubMed

Fan, Changhua; Li, Bo; Xiong, Zhengqin

2018-01-15

Nitrification inhibitors, a promising tool for reducing nitrous oxide (N 2 O) losses and promoting nitrogen use efficiency by slowing nitrification, have gained extensive attention worldwide. However, there have been few attempts to explore the broad responses of multiple reactive gaseous nitrogen emissions of N 2 O, nitric oxide (NO) and ammonia (NH 3 ) and vegetable yield to nitrification inhibitor applications across intensive vegetable soils in China. A greenhouse pot experiment with five consecutive vegetable crops was performed to assess the efficacies of two nitrification inhibitors, namely, nitrapyrin and dicyandiamide on reactive gaseous nitrogen emissions, vegetable yield and reactive gaseous nitrogen intensity in four typical vegetable soils representing the intensive vegetable cropping systems across mainland China: an Acrisol from Hunan Province, an Anthrosol from Shanxi Province, a Cambisol from Shandong Province and a Phaeozem from Heilongjiang Province. The results showed soil type had significant influences on reactive gaseous nitrogen intensity, with reactive gaseous nitrogen emissions and yield mainly driven by soil factors: pH, nitrate, C:N ratio, cation exchange capacity and microbial biomass carbon. The highest reactive gaseous nitrogen emissions and reactive gaseous nitrogen intensity were in Acrisol while the highest vegetable yield occurred in Phaeozem. Nitrification inhibitor applications decreased N 2 O and NO emissions by 1.8-61.0% and 0.8-79.5%, respectively, but promoted NH 3 volatilization by 3.2-44.6% across all soils. Furthermore, significant positive correlations were observed between inhibited N 2 O+NO and stimulated NH 3 emissions with nitrification inhibitor additions across all soils, indicating that reduced nitrification posed the threat of NH 3 losses. Additionally, reactive gaseous nitrogen intensity was significantly reduced in the Anthrosol and Cambisol due to the reduced reactive gaseous nitrogen emissions and increased yield, respectively. Our findings highlight the benefits of nitrification inhibitors for integrating environment and agronomy in intensive vegetable ecosystems in China. Copyright © 2017. Published by Elsevier B.V.

Acid etching of titanium for bonding with veneering composite resins.

PubMed

Ban, Seiji; Taniki, Toshio; Sato, Hideo; Kono, Hiroshi; Iwaya, Yukari; Miyamoto, Motoharu

2006-06-01

Commercially pure titanium (cpTi) was etched using three concentrated acids: 18% HCl, 43% H3PO4, and 48% H2SO4. The bond strengths between five types of veneering composite resin and eight cpTi treatments (involving combinations of sandblasting, acid etching in 48% H2SO4, and vacuum firing) were determined before and after 10,000 and 20,000 thermal cycles. There were no significant differences in the bond strength of resin to cpTi after etching in 48% H2SO4 at 90 degrees C for 15 minutes, at 60 degrees C for 15, 30, or 60 minutes, and after sandblasting with and without vacuum firing (p > 0.05); moreover, these treatments yielded the highest values. As for vacuum firing, it had no significant effect on resin bond strength to cpTi before or after 10,000 and 20,000 thermal cycles. We therefore concluded that acid etching in concentrated H2SO4 is a simple and effective surface modification method of titanium for bonding to veneering composite resins.

Investigation of morphological, structural, and mechanical characteristics of Zircaloy-4 irradiated with 3.5 MeV hydrogen ions beam

NASA Astrophysics Data System (ADS)

Rafique, Mohsin; Butt, M. Z.; Ahmad, Sajjad

2017-09-01

Zircaloy-4 specimens were irradiated with 3.5 MeV hydrogen ions (dose range: 1  ×  1013 H+1 cm-2 to 1  ×  1015 H+1 cm-2) using a Pelletron accelerator. FESEM studies reveal formation of hydrogen micro-bubbles, bubbles induced blisters of irregular shapes, and development of cracks on the specimen surface, as in the case of pure zirconium. However, for the highest irradiation dose of 1  ×  1015 H+1 cm-2, agglomeration of flower-shape blisters is observed. XRD analysis shows that the most preferentially oriented crystallographic plane is (0 0 4) with texture coefficient values 1.832-2.308 depending on the ions dose. Its diffraction peak intensity first decreases with the increase in ions dose up to 5  ×  1013 H+1 cm-2 and later increases up to 1  ×  1015 H+1 cm-2. Opposite is found in case of diffraction peak width. Crystallite size and lattice strain determined by Williamson-Hall analysis display a linear relationship between the two with positive slope. Mechanical strength, namely yield stress (YS), ultimate tensile strength (UTS), and fracture stress (FS), increases sharply with ions dose up to 5  ×  1013 H+1 cm-2. For 1  ×  1014 H+1 cm-2 dose there is a sudden drop of stress to a lowest value and then a slow steady increase in stress up to the highest dose 1  ×  1015 H+1 cm-2. Same pattern is followed by uniform elongation and total elongation. All three stress parameters YS, UTS, and FS follow Inverse Hall-Petch relation.

Development of large diameter carbon monofilament

NASA Technical Reports Server (NTRS)

Jacob, B.; Neltri, R. D.

1973-01-01

A process for preparing large diameter carbon-boron monofilament was developed. The process involves chemical vapor depositing a carbon-boron alloy monofilament from a BCl3, CH4, and H2 gas mixture onto a carbon substrate. Amorphous alloys were formed when gaseous mixtures containing greater than 20 percent methane (80 percent BCl3) were used. The longest uninterrupted lengths of carbon-boron monofilament were produced using a CH4/BCl3 gas ratio of 2.34. It was found that the properties of the carbon-boron alloy monofilament improved when the carbon substrate was precleaned in chlorine. The highest strength monofilament was attained when a CH4/BCl3 gas volume ratio of 0.44 was 28 million N/sq cm (40 million psi). While the highest strengths were attained in this run, the 0.44 gas ratio and other CH4/BCl3 ratios less than 2.34 would not yield long runs. Runs using these ratios were usually terminated because of a break in the monofilament within the reactor. It is felt better process control could probably be achieved by varying the amount of hydrogen; the BCl3/H2 ratio was kept constant in these studies.

Temperature affects long-term productivity and quality attributes of day-neutral strawberry for a space life-support system

NASA Astrophysics Data System (ADS)

Massa, Gioia D.; Chase, Elaine; Santini, Judith B.; Mitchell, Cary A.

2015-04-01

Strawberry (Fragaria x ananassa L.) is a promising candidate crop for space life-support systems with desirable sensory quality and health attributes. Day-neutral cultivars such as 'Seascape' are adaptable to a range of photoperiods, including short days that would save considerable energy for crop lighting without reductions in productivity or yield. Since photoperiod and temperature interact to affect strawberry growth and development, several diurnal temperature regimes were tested under a short photoperiod of 10 h per day for effects on yield and quality attributes of 'Seascape' strawberry during production cycles longer than 270 days. The coolest day/night temperature regime, 16°/8 °C, tended to produce smaller numbers of larger fruit than did the intermediate temperature range of 18°/10 °C or the warmest regime, 20°/12 °C, both of which produced similar larger numbers of smaller fruit. The intermediate temperature regime produced the highest total fresh mass of berries over an entire production cycle. Independent experiments examined either organoleptic or physicochemical quality attributes. Organoleptic evaluation indicated that fruit grown under the coolest temperature regime tended to score the highest for both hedonic preference and descriptive evaluation of sensory attributes related to sweetness, texture, aftertaste, and overall approval. The physicochemical quality attributes Brix, pH, and sugar/acid ratio were highest for fruits harvested from the coolest temperature regime and lower for those from the warmer temperature regimes. The cool-regime fruits also were lowest in titratable acidity. The yield parameters fruit number and size oscillated over the course of a production cycle, with a gradual decline in fruit size under all three temperature regimes. Brix and titratable acidity both decreased over time for all three temperature treatments, but sugar/acid ratio remained highest for the cool temperature regime over the entire production period. Periodic rejuvenation or replacement of strawberry propagules may be needed to maintain both quality and quantity of strawberry yield in space.

Structural elucidation of sorghum lignins from an integrated biorefinery process based on hydrothermal and alkaline treatments.

PubMed

Sun, Shao-Long; Wen, Jia-Long; Ma, Ming-Guo; Sun, Run-Cang

2014-08-13

An integrated process based on hydrothermal pretreatment (HTP) (i.e., 110-230 °C, 0.5-2.0 h) and alkaline post-treatment (2% NaOH at 90 °C for 2.0 h) has been performed for the production of xylooligosaccharide, lignin, and digestible substrate from sweet sorghum stems. The yield, purity, dissociation mechanisms, structural features, and structural transformations of alkali lignins obtained from the integrated process were investigated. It was found that the HTP process facilitated the subsequent alkaline delignification, releasing lignin with the highest yield (79.3%) and purity from the HTP residue obtained at 190 °C for 0.5 h. All of the results indicated that the cleavage of the β-O-4 linkages and degradation of β-β and β-5 linkages occurred under the harsh HTP conditions. Depolymerization and condensation reactions simultaneously occurred at higher temperatures (≥ 170 °C). Moreover, the thermostability of lignin was positively related to its molecular weight, but was also affected by the inherent structures, such as β-O-4 linkages and condensed units. These findings will enhance the understanding of structural transformations of the lignins during the integrated process and maximize the potential utilizations of the lignins in a current biorefinery process.

Mannitol production by lactic acid bacteria grown in supplemented carob syrup.

PubMed

Carvalheiro, Florbela; Moniz, Patrícia; Duarte, Luís C; Esteves, M Paula; Gírio, Francisco M

2011-01-01

Detailed kinetic and physiological characterisation of eight mannitol-producing lactic acid bacteria, Leuconostoc citreum ATCC 49370, L. mesenteroides subsp. cremoris ATCC19254, L. mesenteroides subsp. dextranicum ATCC 19255, L. ficulneum NRRL B-23447, L. fructosum NRRL B-2041, L. lactis ATCC 19256, Lactobacillus intermedius NRRL 3692 and Lb. reuteri DSM 20016, was performed using a carob-based culture medium, to evaluate their different metabolic capabilities. Cultures were thoroughly followed for 30 h to evaluate consumption of sugars, as well as production of biomass and metabolites. All strains produced mannitol at high yields (>0.70 g mannitol/g fructose) and volumetric productivities (>1.31 g/l h), and consumed fructose and glucose simultaneously, but fructose assimilation rate was always higher. The results obtained enable the studied strains to be divided mainly into two groups: one for which glucose assimilation rates were below 0.78 g/l h (strains ATCC 49370, ATCC 19256 and ATCC 19254) and the other for which they ranged between 1.41 and 1.89 g/l h (strains NRRL B-3692, NRRL B-2041, NRRL B-23447 and DSM 20016). These groups also exhibited different mannitol production rates and yields, being higher for the strains with faster glucose assimilation. Besides mannitol, all strains also produced lactic acid and acetic acid. The best performance was obtained for L. fructosum NRRL B-2041, with maximum volumetric productivity of 2.36 g/l h and the highest yield, stoichiometric conversion of fructose to mannitol.

Comparison of bio-hydrogen production yield capacity between asynchronous and simultaneous saccharification and fermentation processes from agricultural residue by mixed anaerobic cultures.

PubMed

Li, Yameng; Zhang, Zhiping; Zhu, Shengnan; Zhang, Huan; Zhang, Yang; Zhang, Tian; Zhang, Quanguo

2018-01-01

Taken common agricultural residues as substrate, dark fermentation bio-hydrogen yield capacity from asynchronous saccharification and fermentation (ASF) and simultaneous saccharification and fermentation (SSF) was investigated. The highest hydrogen yield of 472.75mL was achieved with corncob using ASF. Hydrogen yield from corn straw, rice straw, corncob and sorghum stalk by SSF were 20.54%,10.31%,13.99% and 5.92% higher than ASF, respectively. The experimental data fitted well to the modified Gompertz model. SSF offered a distinct advantage over ASF with respect to reducing overall process time (60h of SSF, 108h of ASF). Meanwhile, SSF performed better than SSF with respect to shortening the lag-stage. The major metabolites of anaerobic fermentation hydrogen production by ASF and SSF were butyric acid and acetic acid. Copyright © 2017 Elsevier Ltd. All rights reserved.

Influence of oxidative stress and grains on sclerotial biomass and carotenoid yield of Penicillium sp. PT95.

PubMed

Chen, Shu-Jun; Wang, Qi; Han, Jian-Rong

2010-08-01

Oxidative stress and grains were evaluated for carotenoid production by solid-state fermentation using Penicillium sp. PT95. When the fungus was grown at high oxidative stress, its sclerotial biomass and carotenoid content in sclerotia increased significantly with respect to low oxidative stress (P < 0.01). High oxidative stress also caused a statistically significant increase in carotenoid yield as compared with low oxidative stress (P < 0.01). Both the sclerotial biomass and the amount of carotenoid accumulated in sclerotia of strain PT95 were strongly dependent on the grain medium used. Among the grain media tested under high oxidative stress, buckwheat medium gave the highest content of carotenoid in sclerotia (828 microg/g dry sclerotia), millet medium gave respectively the highest sclerotial biomass (12.69 g/100 g grain) and carotenoid yield (10.152 mg/100 g grain). Copyright 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

Characterization of dross and its recovery by sulphuric acid leaching

NASA Astrophysics Data System (ADS)

Rahmani, S. A.; Meidianto, A.; Amal, M. I.; Wismogroho, A. S.; Widayatno, W. B.

2018-03-01

This paper reports the characterization of dross from galvanizing process and its recovery using acidic leaching method. The diffraction profile of dross showed identical peaks with that of ZnO. The X-ray Fluorescence (XRF) analysis identified the content of following metals: Zn, Fe, Mn, Ga, Co, and W. The thermal behaviour examination revealed the existence of some volatiles within the initial sample. The acidic leaching at various concentrations of sulphuric acid was conducted to determine the optimum concentration for zinc recovery and the highest yield of zinc sulphate. It is concluded that the optimum concentration of H2SO4 for this kind of dross is 4 M with 71.9% yield of ZnSO4. The result of leaching process was confirmed by infrared spectrum, where various absorptions corresponding to SO4 2- and Zn-O bands were observed.

Effect of various factors on ethanol yields from lignocellulosic biomass by Thermoanaerobacterium AK₁₇.

PubMed

Almarsdottir, Arnheidur Ran; Sigurbjornsdottir, Margret Audur; Orlygsson, Johann

2012-03-01

The ethanol production capacity from sugars and lignocellulosic biomass hydrolysates (HL) by Thermoanaerobacterium strain AK(17) was studied in batch cultures. The strain converts various carbohydrates to, acetate, ethanol, hydrogen, and carbon dioxide. Ethanol yields on glucose and xylose were 1.5 and 1.1 mol/mol sugars, respectively. Increased initial glucose concentration inhibited glucose degradation and end product formation leveled off at 30 mM concentrations. Ethanol production from 5 g L(-1) of complex biomass HL (grass, hemp, wheat straw, newspaper, and cellulose) (Whatman paper) pretreated with acid (0.50% H(2) SO(4)), base (0.50% NaOH), and without acid/base (control) and the enzymes Celluclast and Novozyme 188 (0.1 mL g(-1) dw; 70 and 25 U g(-1) of Celluclast and Novozyme 188, respectively) was investigated. Highest ethanol yields (43.0 mM) were obtained on cellulose but lowest on hemp leafs (3.6 mM). Chemical pretreatment increased ethanol yields substantially from lignocellulosic biomass but not from cellulose. The influence of various factors (HL, enzyme, and acid/alkaline concentrations) on end-product formation from 5 g L(-1) of grass and cellulose was further studied to optimize ethanol production. Highest ethanol yields (5.5 and 8.6 mM ethanol g(-1) grass and cellulose, respectively) were obtained at very low HL concentrations (2.5 g L(-1)); with 0.25% acid/alkali (v/v) and 0.1 mL g(-1) enzyme concentrations. Inhibitory effects of furfural and hydroxymethylfurfural during glucose fermentation, revealed a total inhibition in end product formation from glucose at 4 and 6 g L(-1), respectively. Copyright © 2011 Wiley Periodicals, Inc.

Effects of organic fertilizers on soil physicochemistry and on the yield and botanical composition of forage over 3 years.

PubMed

Matos-Moreira, Mariana; López-Mosquera, M Elvira; Cunha, Mario; Sáinz Osés, María Jesús; Rodríguez, Teresa; Carral, Emilio V

2011-07-01

Organic wastes have been reported to reduce saturation of the exchange complex by Al in Al-rich acid soils. For 3 years, the main soil fertility properties were studied in plots sown with mixed pasture species. These plots were fertilized with cattle slurry, dairy sludge (DS), or granulated broiler litter (BL) in comparison with mineral fertilizer. Al saturation levels were low after the initial inorganic liming treatment (19.00-33.71%) but tended to rise under all treatments (21.09-61.37%) except BL (8.45-30.98%), which was also associated with the highest average soil pH and the highest average levels of exchangeable Ca2+, Mg2+, and K+. Treatment DS performed similarly to mineral fertilizer in most respects, but it led to greater available P levels. Under the dry conditions of the second and third years of the study, BL and DS treatments were associated with significantly greater forage yields than the other treatments. Under DS treatment, available P levels were too low to allow the maintenance of mixed pasture, clover being eliminated by the less P-dependent species.

Effects of Organic Fertilizers on Soil Physicochemistry and on the Yield and Botanical Composition of Forage over 3 Years.

PubMed

Matos-Moreira, Mariana; Elvira López-Mosquera, M; Cunha, Mario; Jesús Sáinz Osés, María; Rodríguez, Teresa; Carral, Emilio V

2011-07-01

Organic wastes have been reported to reduce saturation of the exchange complex by Al in Al-rich acid soils. For 3 years, the main soil fertility properties were studied in plots sown with mixed pasture species. These plots were fertilized with cattle slurry, dairy sludge (DS), or granulated broiler litter (BL) in comparison with mineral fertilizer. Al saturation levels were low after the initial inorganic liming treatment (19.00-33.71%) but tended to rise under all treatments (21.09-61.37%) except BL (8.45-30.98%), which was also associated with the highest average soil pH and the highest average levels of exchangeable Ca 2+ , Mg 2+ , and K + . Treatment DS performed similarly to mineral fertilizer in most respects, but it led to greater available P levels. Under the dry conditions of the second and third years of the study, BL and DS treatments were associated with significantly greater forage yields than the other treatments. Under DS treatment, available P levels were too low to allow the maintenance of mixed pasture, clover being eliminated by the less P-dependent species. [Box: see text].

Characterization of aspartame-cyclodextrin complexation.

PubMed

Sohajda, Tamás; Béni, Szabolcs; Varga, Erzsébet; Iványi, Róbert; Rácz, Akos; Szente, Lajos; Noszál, Béla

2009-12-05

The inclusion complex formation of aspartame (guest) and various cyclodextrins (host) were examined using 1H NMR titration and capillary electrophoresis. Initially the protonation constants of aspartame were determined by NMR-pH titration with in situ pH measurement to yield log K1=7.83 and log K2=2.96. Based on these values the stability of the complexes formed by aspartame and 21 different cyclodextrins (CDs) were studied at pH 2.5, pH 5.2 and pH 9.0 values where aspartame exists predominantly in monocationic, zwitterionic and monoanionic form, respectively. The host cyclodextrin derivatives differed in various sidechains, degree of substitution, charge and purity so that the effect of these properties could be examined systematically. Concerning size, the seven-membered beta-cyclodextrin and its derivatives have been found to be the most suitable host molecules for complexation. Highest stability was observed for the acetylated derivative with a degree of substitution of 7. The purity of the CD enhanced the complexation while the degree of substitution did not provide obvious consequences. Finally, geometric aspects of the inclusion complex were assessed by 2D ROESY NMR and molecular modelling which proved that the guest's aromatic ring enters the wider end of the host cavity.

Electron-stimulated reactions in nanoscale water films adsorbed on α-Al 2O 3 (0001)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Petrik, Nikolay G.; Kimmel, Gregory A.

The radiation-induced decomposition and desorption of nanoscale amorphous solid water (D2O) films adsorbed on -Al2O3(0001) surface was studied at low temperature in ultrahigh vacuum using temperature programmed desorption (TPD) and electron stimulated desorption (ESD) with a mono-energetic, low energy electron source. ESD yields of molecular products ( D2, O2 and D¬2O) and the total sputtering yield increased with increasing D2O coverage up to ~15 water monolayers (i.e. ~15 1015 cm-2) to a coverage-independent level for thicker water films. Experiments with isotopically-layered water films (D2O and H2O) demonstrated that the highest water decomposition yields occurred at the interfaces of the nanoscalemore » water films with the alumina substrate and vacuum. However, the increased reactivity of the water/alumina interface is relatively small compared to the enhancements in the non-thermal reactions previously observed at the water/Pt(111) and water/TiO2(110) interfaces. We propose that the relatively low activity of Al2O3(0001) for the radiation-induced production of molecular hydrogen is associated with lower reactivity of this surface with hydrogen atoms, which are likely precursors for the molecular hydrogen.100 eV electrons are stopped in the H 2O portion of the isotopically-layered nanoscale film on α-Al 2O 3(0001) but D 2is produced at the D 2O/alumina interface by mobile electronic excitations and/or hydronium ions.« less

Cardboard proportions and total solids contents as driving factors in dry co-fermentation of food waste.

PubMed

Capson-Tojo, Gabriel; Trably, Eric; Rouez, Maxime; Crest, Marion; Bernet, Nicolas; Steyer, Jean-Philippe; Delgenès, Jean-Philippe; Escudié, Renaud

2018-01-01

This study evaluated the influence of the co-substrate proportions (0-60% of cardboard in dry basis) and the initial total solid contents (20-40%) on the batch fermentation performance. Maximum hydrogen yields were obtained when mono-fermenting food waste at high solids contents (89mlH 2 ·gVS -1 ). The hydrogen yields were lower when increasing the proportions of cardboard. The lower hydrogen yields at higher proportions of cardboard were translated into higher yields of caproic acid (up to 70.1gCOD·kgCOD bio -1 ), produced by consumption of acetic acid and hydrogen. The highest substrate conversions were achieved at low proportions of cardboard, indicating a stabilization effect due to higher buffering capacities in co-fermentation. Clostridiales were predominant in all operational conditions. This study opens up new possibilities for using the cardboard proportions for controlling the production of high added-value products in dry co-fermentation of food waste. Copyright © 2017 Elsevier Ltd. All rights reserved.

Performances of different protocols for exocellular polysaccharides extraction from milk acid gels: Application to yogurt.

PubMed

Nguyen, An Thi-Binh; Nigen, Michaël; Jimenez, Luciana; Ait-Abderrahim, Hassina; Marchesseau, Sylvie; Picart-Palmade, Laetitia

2018-01-15

Dextran or xanthan were used as model exocellular polysaccharides (EPS) to compare the extraction efficiency of EPS from skim milk acid gels using three different protocols. Extraction yields, residual protein concentrations and the macromolecular properties of extracted EPS were determined. For both model EPS, the highest extraction yield (∼80%) was obtained when samples were heated in acidic conditions at the first step of extraction (Protocol 1). Protocols that contained steps of acid/ethanol precipitation without heating (Protocols 2 and 3) show lower extraction yields (∼55%) but allow a better preservation of the EPS macromolecular properties. Changing the pH of acid gels up to 7 before extraction (Protocol 3) improved the extraction yield of anionic EPS without effect on the macromolecular properties of EPS. Protocol 1 was then applied for the quantification of EPS produced during the yogurt fermentation, while Protocol 3 was dedicated to their macromolecular characterization. Copyright © 2017 Elsevier Ltd. All rights reserved.

Quantum yield measurements of light-induced H₂ generation in a photosystem I-[FeFe]-H₂ase nanoconstruct.

PubMed

Applegate, Amanda M; Lubner, Carolyn E; Knörzer, Philipp; Happe, Thomas; Golbeck, John H

2016-01-01

The quantum yield for light-induced H2 generation was measured for a previously optimized bio-hybrid cytochrome c 6-crosslinked PSI(C13G)-1,8-octanedithiol-[FeFe]-H2ase(C97G) (PSI-H2ase) nanoconstruct. The theoretical quantum yield for the PSI-H2ase nanoconstruct is 0.50 molecules of H2 per photon absorbed, which equates to a requirement of two photons per H2 generated. Illumination of the PSI-H2ase nanoconstruct with visible light between 400 and 700 nm resulted in an average quantum yield of 0.10-0.15 molecules of H2 per photon absorbed, which equates to a requirement of 6.7-10 photons per H2 generated. A possible reason for the difference between the theoretical and experimental quantum yield is the occurrence of non-productive PSI(C13G)-1,8-octanedithiol-PSIC13G (PSI-PSI) conjugates, which would absorb light without generating H2. Assuming the thiol-Fe coupling is equally efficient at producing PSI-PSI conjugates as well as in producing PSI-H2ase nanoconstructs, the theoretical quantum yield would decrease to 0.167 molecules of H2 per photon absorbed, which equates to 6 photons per H2 generated. This value is close to the range of measured values in the current study. A strategy that purifies the PSI-H2ase nanoconstructs from the unproductive PSI-PSI conjugates or that incorporates different chemistries on the PSI and [FeFe]-H2ase enzyme sites could potentially allow the PSI-H2ase nanoconstruct to approach the expected theoretical quantum yield for light-induced H2 generation.

Enhanced catalytic efficiency of endo-β-agarase I by fusion of carbohydrate-binding modules for agar prehydrolysis.

PubMed

Alkotaini, Bassam; Han, Nam Soo; Kim, Beom Soo

2016-11-01

Recently, Microbulbifer thermotolerans JAMB-A94 endo-β-agarase I was expressed as catalytic domain (GH16) without a carbohydrate-binding module (CBM). In this study, we successfully constructed different fusions of GH16 with its original CBM6 and CBM13 derived from Catenovulum agarivorans. The optimum temperature and pH for fusions GH16-CBM6, GH16-CBM13, GH16-CBM6-CBM13 and GH16-CBM13-CBM6 were similar to GH16, at 55°C and pH 7. All the constructed fusions significantly enhanced the GH16 affinity (Km) and the catalytic efficiency (Kcat/Km) toward agar. Among them, GH16-CBM6-CBM13 exhibited the highest agarolytic activity, for which Km decreased from 3.67 to 2.11mg/mL and Kcat/Km increased from 98.6 (mg/mL) -1 sec -1 to 400.6 (mg/mL) -1 sec -1 . Moreover, all fusions selectively increased GH16 binding ability to agar, in which the highest binding ability of 95% was obtained with fusion GH16-CBM6-CBM13. Melted agar was prehydrolyzed with GH16-CBM6-CBM13, resulting in a degree of liquefaction of 45.3% and reducing sugar yield of 14.2%. Further addition of Saccharophagus degradans agarolytic enzymes resulted in mono-sugar yields of 35.4% for galactose and 31.5% for 3,6-anhydro-l-galactose. There was no pH neutralization step required and no 5-hydroxymethylfurfural detected, suggesting the potential of a new enzymatic prehydrolysis process for efficient production of bio-products such as biofuels. Copyright © 2016 Elsevier Inc. All rights reserved.

Characterization of cellulose production by a Gluconacetobacter xylinus strain from Kombucha.

PubMed

Nguyen, Vu Tuan; Flanagan, Bernadine; Gidley, Michael J; Dykes, Gary A

2008-11-01

The aims of this work were to characterize and improve cellulose production by a Gluconoacetobacter xylinus strain isolated from Kombucha and determine the purity and some structural features of the cellulose from this strain. Cellulose yield in tea medium with both black tea and green tea and in Hestrin and Schramm (HS) medium under both static and agitated cultures was compared. In the tea medium, the highest cellulose yield was obtained with green tea (approximately 0.20 g/L) rather than black tea (approximately 0.14 g/L). Yield in HS was higher (approximately 0.28 g/L) but did not differ between static and agitated incubation. (1)H-NMR and (13)C-NMR spectroscopy indicated that the cellulose is pure (free of acetan) and has high crystallinity, respectively. Cellulose yield was improved by changing the type and level of carbon and nitrogen source in the HS medium. A high yield of approximately 2.64 g/L was obtained with mannitol at 20 g/L and corn steep liquor at 40 g/L in combination. In the tea medium, tea at a level of 3 g/L gave the highest cellulose yield and the addition of 3 g/L of tea to the HS medium increased cellulose yield to 3.34 g/L. In conclusion, the G. xylinus strain from Kombucha had different cellulose-producing characteristics than previous strains isolated from fruit. Cellulose was produced in a pure form and showed high potential applicability. Our studies extensively characterized cellulose production from a G. xylinus strain from Kombucha for the first time, indicating both similarities and differences to strains from different sources.

Enhancing the production of eicosapentaenoic acid (EPA) from Nannochloropsis oceanica CY2 using innovative photobioreactors with optimal light source arrangements.

PubMed

Chen, Chun-Yen; Chen, Yu-Chun; Huang, Hsiao-Chen; Ho, Shih-Hsin; Chang, Jo-Shu

2015-09-01

Binary combinations of LEDs with four different colors were used as light sources to identify the effects of multiple wavelengths on the production of eicosapentaenoic acid (EPA) by an isolated microalga Nannochloropsis oceanica CY2. Combining LED-Blue and LED-Red could give the highest EPA productivity of 13.24 mg L(-1) d(-1), which was further enhanced to 14.4 mg L(-1) d(-1) when using semi-batch operations at a 40% medium replacement ratio. A novel photobioreactor with additional immersed light sources improved light penetration efficiency and led to an 38% (0.170-0.235 g L(-1) d(-1)) increase in the microalgae biomass productivity and a 9% decrease in electricity consumption yield of EPA (10.15-9.33 kW-h (g EPA)(-1)) when compared with the control (i.e., without immersed light sources). Operating the immersed LEDs at a flashing-frequency of 9 Hz further lowered the energy consumption yield to 8.87 kW-h (g EPA)(-1). Copyright © 2015 Elsevier Ltd. All rights reserved.

Production of biohythane from food waste via an integrated system of continuously stirred tank and anaerobic fixed bed reactors.

PubMed

Yeshanew, Martha M; Frunzo, Luigi; Pirozzi, Francesco; Lens, Piet N L; Esposito, Giovanni

2016-11-01

The continuous production of biohythane (mixture of biohydrogen and methane) from food waste using an integrated system of a continuously stirred tank reactor (CSTR) and anaerobic fixed bed reactor (AFBR) was carried out in this study. The system performance was evaluated for an operation period of 200days, by stepwise shortening the hydraulic retention time (HRT). An increasing trend of biohydrogen in the CSTR and methane production rate in the AFBR was observed regardless of the HRT shortening. The highest biohydrogen yield in the CSTR and methane yield in the AFBR were 115.2 (±5.3)L H2/kgVSadded and 334.7 (±18.6)L CH4/kgCODadded, respectively. The AFBR presented a stable operation and excellent performance, indicated by the increased methane production rate at each shortened HRT. Besides, recirculation of the AFBR effluent to the CSTR was effective in providing alkalinity, maintaining the pH in optimal ranges (5.0-5.3) for the hydrogen producing bacteria. Copyright © 2016 Elsevier Ltd. All rights reserved.

Increase of ethanol productivity by cell-recycle fermentation of flocculating yeast.

PubMed

Wang, F Z; Xie, T; Hui, M

2011-01-01

Using the recombinant flocculating Angel yeast F6, long-term repeated batch fermentation for ethanol production was performed and a high volumetric productivity resulted from half cells not washed and the optimum opportunity of residual glucose 20 g l(-1) of last medium. The obtained highest productivity was 2.07 g l-(1) h(-1), which was improved by 75.4% compared with that of 1.18 g l(-1) h(-1) in the first batch fermentation. The ethanol concentration reached 8.4% corresponding to the yield of 0.46 g g(-1). These results will contribute greatly to the industrial production of fuel ethanol using the commercial method with the flocculating yeast.

Continuous ethanol production from cheese whey fermentation by Candida pseudotropicalis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghaly, A.E.; El-Taweel, A.A.

1997-12-01

Three pilot-scale continuous mix reactors of 5-L volume each were used to study the effects of retention time (18--42 hours) and initial substrate concentration (50--150 g/L) on the cell yield, lactose consumption, and maximum ethanol concentration during continuous fermentation of cheese whey using the yeast Candida pseudotropicalis. A microaeration rate of 480 mL/min and a nutrient supplement (yeast extract) concentration of 0.1% vol/vol were used. The results indicated that the dissolved oxygen concentration, temperature, cell concentration, lactose utilization rate, and ethanol concentration were affected by hydraulic retention time and initial substrate concentration. The highest cell concentration of 5.46 g/L andmore » the highest ethanol concentration of 57.96 g/L (with a maximum ethanol yield of 99.6% from the theoretical yield) were achieved at the 42-hour hydraulic retention time and the 150 g/L initial substrate concentration, whereas the highest cell yield was observed at the 50 g/L initial substrate concentration and the 36-hour hydraulic retention time. Lactose utilizations of 98, 91, and 83% were obtained with 50, 100, and 150 g/L initial substrate concentrations at the 42-hour hydraulic retention time. A pH control system was found unnecessary.« less

Effects of pH-Shift Processing and Microbial Transglutaminase on the Gel and Emulsion Characteristics of Porcine Myofibrillar System

PubMed Central

Hong, Geun-Pyo; Chun, Ji-Yeon; Jo, Yeon-Ji

2014-01-01

This study investigated the effects of microbial transglutaminase (MTGase) and pH-shift processing on the functional properties of porcine myofibrillar proteins (MP). The pH-shift processing was carried out by decreasing the pH of MP suspension to 3.0, followed by re-adjustment to pH 6.2. The native (CM) and pH-shifted MP (PM) was reacted with and without MTGase, and the gelling and emulsion characteristics were compared. To compare the pH-shifted MTGase-treated MP (PT), deamidation (DM) was conducted by reacting MTGase with MP at pH 3.0. Rigid thermal gel was produced by MTGase-treated native MP (CT) and PT. PM and DM showed the lowest storage modulus (G') at the end of thermal scanning. Both MTGase and pH-shifting produced harder MP gel, and the highest gel strength was obtained in PT. All treatments yielded lower than CM, and CT showed significantly higher yield than PM and DM treatments. For emulsion characteristics, pH-shifting improved the emulsifying ability of MP-stabilized emulsion, while the treatments had lower emulsion stability. PM-stabilized emulsion exhibited the lowest creaming stability among all treatments. The emulsion stability could be improved by the usage of MTGase. The results indicated that pH-shifting combined with MTGase had a potential application to modify or improve functional properties of MP in manufacturing of meat products. PMID:26760940

Electrocatalytic reduction of CO2 with CCC-NHC pincer nickel complexes.

PubMed

Cope, James D; Liyanage, Nalaka P; Kelley, Paul J; Denny, Jason A; Valente, Edward J; Webster, Charles Edwin; Delcamp, Jared H; Hollis, T Keith

2017-08-22

A CCC-NHC pincer Ni(ii)Cl complex was prepared according to the metallation/transmetallation methodology. It was fully characterized by electrochemical, NMR spectroscopic, theoretical, and X-ray crystallographic methods. The complex and its cation were evaluated for electrocatalytic reduction of CO 2 under a variety of conditions and found to provide some of the fastest catalytic rates and highest substrate selectivities (CO 2 vs. H + ) reported. Rates improved in the presence of water and, significantly, catalysis occurred at the first reduction potential, presumably at the Ni(i) state. Controlled potential electrolysis (CPE) was found to yield CO at 34% and formate at 47% Faradaic efficiency (FE).

Effect of Copper Oxide Concentration on the Formation and Persistency of Environmentally Persistent Free Radicals (EPFRs) in Particulates

PubMed Central

2015-01-01

Environmentally persistent free radicals (EPFRs) are formed by the chemisorption of substituted aromatics on metal oxide surfaces in both combustion sources and superfund sites. The current study reports the dependency of EPFR yields and their persistency on metal loading in particles (0.25, 0.5, 0.75, 1, 2, and 5% CuO/silica). The EPFRs were generated through exposure of particles to three adsorbate vapors at 230 °C: phenol, 2-monochlorophenol (2-MCP), and dichlorobenzene (DCBz). Adsorption resulted in the formation of surface-bound phenoxyl- and semiquinoine-type radicals with characteristic EPR spectra displaying a g value ranging from ∼2.0037 to 2.006. The highest EPFR yield was observed for CuO concentrations between 1 and 3% in relation to MCP and phenol adsorption. However, radical density, which is expressed as the number of radicals per copper atom, was highest at 0.75–1% CuO loading. For 1,2-dichlorobenzene adsorption, radical concentration increased linearly with decreasing copper content. At the same time, a qualitative change in the radicals formed was observed—from semiquinone to chlorophenoxyl radicals. The two longest lifetimes, 25 and 23 h, were observed for phenoxyl-type radicals on 0.5% CuO and chlorophenoxyl-type radicals on 0.75% CuO, respectively. PMID:24437381

Effects of Eliminating Pyruvate Node Pathways and of Coexpression of Heterogeneous Carboxylation Enzymes on Succinate Production by Enterobacter aerogenes

PubMed Central

Yamamoto, Yoko; Fukui, Keita; Nishio, Yousuke; Hashiguchi, Kenichi; Usuda, Yoshihiro; Sode, Koji

2014-01-01

Lowering the pH in bacterium-based succinate fermentation is considered a feasible approach to reduce total production costs. Newly isolated Enterobacter aerogenes strain AJ110637, a rapid carbon source assimilator under weakly acidic (pH 5.0) conditions, was selected as a platform for succinate production. Our previous work showed that the ΔadhE/PCK strain, developed from AJ110637 with inactivated ethanol dehydrogenase and introduced Actinobacillus succinogenes phosphoenolpyruvate carboxykinase (PCK), generated succinate as a major product of anaerobic mixed-acid fermentation from glucose under weakly acidic conditions (pH <6.2). To further improve the production of succinate by the ΔadhE/PCK strain, metabolically engineered strains were designed based on the elimination of pathways that produced undesirable products and the introduction of two carboxylation pathways from phosphoenolpyruvate and pyruvate to oxaloacetate. The highest production of succinate was observed with strain ES04/PCK+PYC, which had inactivated ethanol, lactate, acetate, and 2,3-butanediol pathways and coexpressed PCK and Corynebacterium glutamicum pyruvate carboxylase (PYC). This strain produced succinate from glucose with over 70% yield (gram per gram) without any measurable formation of ethanol, lactate, or 2,3-butanediol under weakly acidic conditions. The impact of lowering the pH from 7.0 to 5.5 on succinate production in this strain was evaluated under pH-controlled batch culture conditions and showed that the lower pH decreased the succinate titer but increased its yield. These findings can be applied to identify additional engineering targets to increase succinate production. PMID:25416770

Coupling Glucose Dehydrogenation with CO2 Hydrogenation by Hydrogen Transfer in Aqueous Media at Room Temperature.

PubMed

Ding, Guodong; Su, Ji; Zhang, Cheng; Tang, Kan; Yang, Lisha; Lin, Hongfei

2018-05-08

Conversion of carbon dioxide into value-added chemicals and fuels provides a direct solution to reduce excessive CO2 in the atmosphere. Herein, a novel catalytic reaction system is presented by coupling the dehydrogenation of glucose with the hydrogenation of a CO2 derived salt, ammonium carbonate, in the ethanol-water mixture. For the first time, the hydrogenation of CO2 into formate by glucose has been achieved under ambient conditions. Under the optimal reaction conditions, the highest yield of formate reached ~ 46 %. We find that the apparent pH value in the ethanol-water mixture plays a central role in determining the performance of the hydrogen transfer reaction. Based on the 13C NMR and ESI-MS results, a possible pathway of the coupled glucose dehydrogenation and CO2 hydrogenation reactions was proposed. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Enterobacter aerogenes metabolites enhance Microcystis aeruginosa biomass recovery for sustainable bioflocculant and biohydrogen production.

PubMed

Xu, Liang; Zhou, Mo; Ju, Hanyu; Zhang, Zhenxing; Zhang, Jiquan; Sun, Caiyun

2018-09-01

We report a recycling bioresource involving harvesting of Microcystis aeruginosa using the bioflocculant (MBF-32) produced by Enterobacter aerogenes followed by the recovery of the harvested M. aeruginosa as the main substrate for the sustainable production of MBF-32 and biohydrogen. The experimental results indicate that the efficiency of bioflocculation exceeded 90% under optimal conditions. The harvested M. aeruginosa was further recycled as the main substrate for the supply of necessary elements. The highest yield (3.6±0.1g/L) of MBF-32 could be obtained from 20g/L of wet biomass of M. aeruginosa with an additional 20g/L of glucose as the extra carbon source. The highest yield of biohydrogen was 35mL of H 2 /g (dw) algal biomass, obtained from 20g/L of wet biomass of M. aeruginosa with an additional 10g/L of glycerol. Transcriptome analyses indicated that MBF-32 was mainly composed of polysaccharide and tyrosine/tryptophan proteins. Furthermore, NADH synthase and polysaccharide export-related genes were found to be up-regulated. Copyright © 2018 Elsevier B.V. All rights reserved.

Study of KOH/Al2O3 as heterogeneous catalyst for biodiesel production via in situ transesterification from microalgae.

PubMed

Ma, Guixia; Hu, Wenrong; Pei, Haiyan; Jiang, Liqun; Ji, Yan; Mu, Ruimin

2015-01-01

Heterogeneous KOH/Al2O3 catalysts, synthesized by the wet impregnation method with different KOH loadings (20-40 wt%) and calcination temperatures from 400°C to 800°C, were used to produce biodiesel from Chlorella vulgaris biomass by in situ transesterification. The highest yield of biodiesel of 89.53±1.58% was achieved at calcination temperature of 700°C for 2 h and 35 wt% loading of KOH, and at the optimal reaction condition of 10 wt% of catalyst content, 8 mL/g of methanol to biomass ratio and at 60°C for 5 h. The characteristics of the catalysts were analysed by X-ray diffraction, scanning electron microscopy and Brunauer-Emmett-Teller.

Characterization of an immobilized cell, trickle bed reactor during long term butanol (ABE) fermentation.

PubMed

Park, C H; Okos, M R; Wankat, P C

1990-06-20

Acetone-butanol-ethanol (ABE) fermentation was performed continuously in an immobilized cell, trickle bed reactor for 54 days without, degeneration by maintaining the pH above 4.3. Column clogging was minimized by structured packing of immobilization matrix. The reactor contained two serial glass columns packed with Clostridium acetobutylicum adsorbed on 12- and 20-in.-long polyester sponge strips at total flow rates between 38 and 98.7 mL/h. Cells were initially grown at 20 g/L glucose resulting in low butanol (1.15 g/L) production encouraging cell growth. After the initial cell growth phase a higher glucose concentration (38.7 g/L) improved solvent yield from 13.2 to 24.1 wt%, and butanol production rate was the best. Further improvement in solvent yield and butanol production rate was not observed with 60 g/L of glucose. However, when the fresh nutrient supply was limited to only the first column, solvent yield increased to 27.3 wt% and butanol selectivity was improved to 0.592 as compared to 0.541 when fresh feed was fed to both columns. The highest butanol concentration of 5.2 g/L occurred at 55% conversion of the feed with 60 g/L glucose. Liquid product yield of immobilized cells approached the theoretical value reported in the literature. Glucose and product concentration profiles along the column showed that the columns can be divided into production and inhibition regions. The length of each zone was dependent upon the feed glucose concentration and feed pattern. Unlike batch fermentation, there was no clear distinction between acid and solvent production regions. The pH dropped, from 6.18-6.43 to 4.50-4.90 in the first inch of the reactor. The pH dropped further to 4.36-4.65 by the exit of the column. The results indicate that the strategy for long term stable operation with high solvent yield requires a structured packing of biologically stable porous matrix such as polyester sponge, a pH maintenance above 4.3, glucose concentrations up to 60 g/L and nutrient supply only to the inlet of the reactor.

Ethanol and Acetic Acid Production from Carbon Monoxide in a Clostridium Strain in Batch and Continuous Gas-Fed Bioreactors

PubMed Central

Nalakath Abubackar, Haris; Veiga, María C.; Kennes, Christian

2015-01-01

The effect of different sources of nitrogen as well as their concentrations on the bioconversion of carbon monoxide to metabolic products such as acetic acid and ethanol by Clostridium autoethanogenum was studied. In a first set of assays, under batch conditions, either NH4Cl, trypticase soy broth or yeast extract (YE) were used as sources of nitrogen. The use of YE was found statistically significant (p < 0.05) on the product spectrum in such batch assays. In another set of experiments, three bioreactors were operated with continuous CO supply, in order to estimate the effect of running conditions on products and biomass formation. The bioreactors were operated under different conditions, i.e., EXP1 (pH = 5.75, YE 1g/L), EXP2 (pH = 4.75, YE 1 g/L) and EXP3 (pH = 5.75, YE 0.2 g/L). When compared to EXP2 and EXP3, it was found that EXP1 yielded the maximum biomass accumulation (302.4 mg/L) and products concentrations, i.e., acetic acid (2147.1 mg/L) and ethanol (352.6 mg/L). This can be attributed to the fact that the higher pH and higher YE concentration used in EXP1 stimulated cell growth and did, consequently, also enhance metabolite production. However, when ethanol is the desired end-product, as a biofuel, the lower pH used in EXP2 was more favourable for solventogenesis and yielded the highest ethanol/acetic acid ratio, reaching a value of 0.54. PMID:25608591

Ethanol and acetic acid production from carbon monoxide in a Clostridium strain in batch and continuous gas-fed bioreactors.

PubMed

Abubackar, Haris Nalakath; Veiga, María C; Kennes, Christian

2015-01-20

The effect of different sources of nitrogen as well as their concentrations on the bioconversion of carbon monoxide to metabolic products such as acetic acid and ethanol by Clostridium autoethanogenum was studied. In a first set of assays, under batch conditions, either NH4Cl, trypticase soy broth or yeast extract (YE) were used as sources of nitrogen. The use of YE was found statistically significant (p < 0.05) on the product spectrum in such batch assays. In another set of experiments, three bioreactors were operated with continuous CO supply, in order to estimate the effect of running conditions on products and biomass formation. The bioreactors were operated under different conditions, i.e., EXP1 (pH = 5.75, YE 1g/L), EXP2 (pH = 4.75, YE 1 g/L) and EXP3 (pH = 5.75, YE 0.2 g/L). When compared to EXP2 and EXP3, it was found that EXP1 yielded the maximum biomass accumulation (302.4 mg/L) and products concentrations, i.e., acetic acid (2147.1 mg/L) and ethanol (352.6 mg/L). This can be attributed to the fact that the higher pH and higher YE concentration used in EXP1 stimulated cell growth and did, consequently, also enhance metabolite production. However, when ethanol is the desired end-product, as a biofuel, the lower pH used in EXP2 was more favourable for solventogenesis and yielded the highest ethanol/acetic acid ratio, reaching a value of 0.54.

Estimating climate change, CO2 and technology development effects on wheat yield in northeast Iran

NASA Astrophysics Data System (ADS)

Bannayan, M.; Mansoori, H.; Rezaei, E. Eyshi

2014-04-01

Wheat is the main food for the majority of Iran's population. Precise estimation of wheat yield change in future is essential for any possible revision of management strategies. The main objective of this study was to evaluate the effects of climate change, CO2 concentration, technology development and their integrated effects on wheat production under future climate change. This study was performed under two scenarios of the IPCC Special Report on Emission Scenarios (SRES): regional economic (A2) and global environmental (B1). Crop production was projected for three future time periods (2020, 2050 and 2080) in comparison with a baseline year (2005) for Khorasan province located in the northeast of Iran. Four study locations in the study area included Mashhad, Birjand, Bojnourd and Sabzevar. The effect of technology development was calculated by fitting a regression equation between the observed wheat yields against historical years considering yield potential increase and yield gap reduction as technology development. Yield relative increase per unit change of CO2 concentration (1 ppm-1) was considered 0.05 % and was used to implement the effect of elevated CO2. The HadCM3 general circulation model along with the CSM-CERES-Wheat crop model were used to project climate change effects on wheat crop yield. Our results illustrate that, among all the factors considered, technology development provided the highest impact on wheat yield change. Highest wheat yield increase across all locations and time periods was obtained under the A2 scenario. Among study locations, Mashhad showed the highest change in wheat yield. Yield change compared to baseline ranged from -28 % to 56 % when the integration of all factors was considered across all locations. It seems that achieving higher yield of wheat in future may be expected in northeast Iran assuming stable improvements in production technology.

Estimating climate change, CO2 and technology development effects on wheat yield in northeast Iran.

PubMed

Bannayan, M; Mansoori, H; Rezaei, E Eyshi

2014-04-01

Wheat is the main food for the majority of Iran's population. Precise estimation of wheat yield change in future is essential for any possible revision of management strategies. The main objective of this study was to evaluate the effects of climate change, CO2 concentration, technology development and their integrated effects on wheat production under future climate change. This study was performed under two scenarios of the IPCC Special Report on Emission Scenarios (SRES): regional economic (A2) and global environmental (B1). Crop production was projected for three future time periods (2020, 2050 and 2080) in comparison with a baseline year (2005) for Khorasan province located in the northeast of Iran. Four study locations in the study area included Mashhad, Birjand, Bojnourd and Sabzevar. The effect of technology development was calculated by fitting a regression equation between the observed wheat yields against historical years considering yield potential increase and yield gap reduction as technology development. Yield relative increase per unit change of CO2 concentration (1 ppm(-1)) was considered 0.05 % and was used to implement the effect of elevated CO2. The HadCM3 general circulation model along with the CSM-CERES-Wheat crop model were used to project climate change effects on wheat crop yield. Our results illustrate that, among all the factors considered, technology development provided the highest impact on wheat yield change. Highest wheat yield increase across all locations and time periods was obtained under the A2 scenario. Among study locations, Mashhad showed the highest change in wheat yield. Yield change compared to baseline ranged from -28 % to 56 % when the integration of all factors was considered across all locations. It seems that achieving higher yield of wheat in future may be expected in northeast Iran assuming stable improvements in production technology.

Simultaneous Biohydrogen and Bioethanol Production from Anaerobic Fermentation with Immobilized Sludge

PubMed Central

Han, Wei; Wang, Zhanqing; Chen, Hong; Yao, Xin; Li, Yongfeng

2011-01-01

The effects of organic loading rates (OLRs) on fermentative productions of hydrogen and ethanol were investigated in a continuous stirred tank reactor (CSTR) with attached sludge using molasses as substrate. The CSTR reactor with attached sludge was operated under different OLRs, ranging from 8 to 24 kg/m3·d. The H2 and ethanol production rate essentially increased with increasing OLR. The highest H2 production rate (10.74 mmol/h·L) and ethanol production rate (11.72 mmol/h·L) were obtained both operating at OLR = 24 kg/m3·d. Linear regression results show that ethanol production rate (y) and H2 production rate (x) were proportionately correlated and can be expressed as y = 1.5365x − 5.054 (r2 = 0.9751). The best energy generation rate was 19.08 kJ/h·L, which occurred at OLR = 24 kg/m3·d. In addition, the hydrogen yield was affected by the presence of ethanol and acetic acid in the liquid phase, and the maximum hydrogen production rate occurred while the ratio of ethanol to acetic acid was close to 1. PMID:21799660

Chemical looping coal gasification with calcium ferrite and barium ferrite via solid--solid reactions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Siriwardane, Ranjani; Riley, Jarrett; Tian, Hanjing

Coal gasification to produce synthesis gas by chemical looping was investigated with two oxygen carriers, barium ferrite (BaFe2O4) and calcium ferrite (CaFe2O4). Thermo-gravimetric analysis (TGA) and fixed-bed flow reactor data indicated that a solid–solid interaction occurred between oxygen carriers and coal to produce synthesis gas. Both thermodynamic analysis and experimental data indicated that BaFe2O4 and CaFe2O4 have high reactivity with coal but have a low reactivity with synthesis gas, which makes them very attractive for the coal gasification process. Adding steam increased the production of hydrogen (H2) and carbon monoxide (CO), but carbon dioxide (CO2) remained low because these oxygenmore » carriers have minimal reactivity with H2 and CO. Therefore, the combined steam–oxygen carrier produced the highest quantity of synthesis gas. It appeared that neither the water–gas shift reaction nor the water splitting reaction promoted additional H2 formation with the oxygen carriers when steam was present. Wyodak coal, which is a sub-bituminous coal, had the best gasification yield with oxygen carrier–steam while Illinois #6 coal had the lowest. The rate of gasification and selectivity for synthesis gas production was significantly higher when these oxygen carriers were present during steam gasification of coal. The rates and synthesis gas yields during the temperature ramps of coal–steam with oxygen carriers were better than with gaseous oxygen.« less

Development of Hospitalization Resource Intensity Scores for Kids (H-RISK) and Comparison across Pediatric Populations.

PubMed

Richardson, Troy; Rodean, Jonathan; Harris, Mitch; Berry, Jay; Gay, James C; Hall, Matt

2018-04-25

In the Medicare population, measures of relative severity of illness (SOI) for hospitalized patents have been used in prospective payment models. Similar measures for pediatric populations have not been fully developed. To develop hospitalization resource intensity scores for kids (H-RISK) using pediatric relative weights (RWs) for SOI and to compare hospital types on case-mix index (CMI). Using the 2012 Kids' Inpatient Database (KID), we developed RWs for each All Patient Refined Diagnosis Related Group (APR-DRG) and SOI level. RW corresponded to the ratio of the adjusted mean cost for discharges in an APR-DRG SOI combination over adjusted mean cost of all discharges in the dataset. RWs were applied to every discharge from 3,117 hospitals in the database with at least 20 discharges. RWs were then averaged at the hospital level to provide each hospital's CMI. CMIs were compared by hospital type using Kruskal- Wallis tests. The overall adjusted mean cost of weighted discharges in Healthcare Cost and Utilization Project KID 2012 was $6,135 per discharge. Solid organ and bone marrow transplantations represented 4 of the 10 highest procedural RWs (range: 35.5 to 91.7). Neonatal APRDRG SOIs accounted for 8 of the 10 highest medical RWs (range: 19.0 to 32.5). Free-standing children's hospitals yielded the highest median (interquartile range [IQR]) CMI (2.7 [2.2-3.1]), followed by urban teaching hospitals (1.8 [1.3-2.6]), urban nonteaching hospitals (1.1 [0.9-1.5]), and rural hospitals (0.8 [0.7-0.9]; P < .001). H-RISK for populations of pediatric admissions are sensitive to detection of substantial differences in SOI by hospital type. © 2018 Society of Hospital Medicine.

Microplate-Based Evaluation of the Sugar Yield from Giant Reed, Giant Miscanthus and Switchgrass after Mild Chemical Pre-Treatments and Hydrolysis with Tailored Trichoderma Enzymatic Blends.

PubMed

Cianchetta, Stefano; Bregoli, Luca; Galletti, Stefania

2017-11-01

Giant reed, miscanthus, and switchgrass are considered prominent lignocellulosic feedstocks to obtain fermentable sugars for biofuel production. The bioconversion into sugars requires a delignifying pre-treatment step followed by hydrolysis with cellulase and other accessory enzymes like xylanase, especially in the case of alkali pre-treatments, which retain the hemicellulose fraction. Blends richer in accessory enzymes than commercial mix can be obtained growing fungi on feedstock-based substrates, thus ten selected Trichoderma isolates, including the hypercellulolytic strain Trichoderma reesei Rut-C30, were grown on giant reed, miscanthus, or switchgrass-based substrates. The produced enzymes were used to saccharify the corresponding feedstocks, compared to a commercial enzymatic mix (6 FPU/g). Feedstocks were acid (H 2 SO 4 0.2-2%, w/v) or alkali (NaOH 0.02-0.2%, w/v) pre-treated. A microplate-based approach was chosen for most of the experimental steps due to the large number of samples. The highest bioconversion was generally obtained with Trichoderma harzianum Or4/99 enzymes (78, 89, and 94% final sugar yields at 48 h for giant reed, miscanthus, and switchgrass, respectively), with significant increases compared to the commercial mix, especially with alkaline pre-treatments. The differences in bioconversion yields were only partially caused by xylanases (maximum R 2  = 0.5), indicating a role for other accessory enzymes.

Rice: Characterizing the Environmental Response of a Gibberellic Acid-Deficient Rice for Use as a Model Crop

NASA Technical Reports Server (NTRS)

Frantz, Jonathan M.; Pinnock, Derek; Klassen, Steve; Bugbee, Bruce

2004-01-01

Rice (Oryza sativa L.) is a useful model crop plant. Rice was the first crop plant to have its complete genome sequenced. Unfortunately, even semi-dwarf rice cultivars are 60 to 90 an tail, and large plant populations cannot be grown in the confined volumes of greenhouses and growth chambers. We recently identified an extremely short (20 em tall) rice line, which is an ideal model for larger rice cultivars. We called this line "Super Dwarf rice." Here we report the response of Super Dwarf to temperature, photoperiod, photosynthetic photon flux (PPF), and factors that can affect time to head emergence. Vegetative biomass increased 6% per degree Celsius, with increasing temperature from 27 to 31 C. Seed yield decreased by 2% per degree Celsius rise in temperature, and as a result, harvest index decreased from 60 to 54%. The time to heading increased by 2 d for every hour above a 12-h photoperiod. Yield increased with increasing PPF up to the highest level tested at 1800 micro-mol/sq m/s (12-h photoperiod; 77.8 mol/sq m/d). Yield efficiency (grams per mole of photons) increased to 900 micro-mol/sq m/s and then slightly decreased at 1800 micro-mol/sq m/s . Heading was delayed by addition of gibberellic acid 3 (GA,) to the root zone but was hastened under mild N stress. Overall, short stature, high yield, high harvest index, and no extraordinary environmental requirements make Super Dwarf rice an excellent model plant for yield studies in controlled environments.

High Temperature Silicides and Refractory Alloys Symposium Held in Boston, Massachusetts on November 29 -December 2, 1993. Volume 322

DTIC Science & Technology

1993-12-02

determined by Leco* analysis with the highest impurity being C (< 91 wt. ppm) followed by 0 (< 39 ppm) and H (< 5 ppm). Results The yield stress of single... Analysis The slip trace analyses made after deformation along [0011, J021), and 17711 are summarized in Table 1. The characteristics of the slip traces...elastic recovery of the material as the indenter is removed. Following their analysis , we used the unloading portion of the curve to estimate the

Effect of pH on H2O2 production in the radiolysis of water.

PubMed

Roth, Olivia; LaVerne, Jay A

2011-02-10

The yields of hydrogen peroxide have been measured in the radiolysis of aqueous solutions of acrylamide, bromide, nitrate, and air in the pH range of 1-13. Hydrogen peroxide is the main stable oxidizing species formed in the radiolysis of water, and its long-term yield is found to be very sensitive to the system used in the measurements. Experiments with γ-irradiation combined with model calculations show that the primary yields of hydrogen peroxide are nearly independent of pH in the range of 2-12. Slightly higher primary yields are suggested at very low pH in particular when O(2) is present, while the yields seem to decrease at very high pH. Irradiations were performed with 5 MeV H ions, 5 MeV He ions, and 10 MeV C ions to evaluate the intratrack and homogeneous kinetic contributions to H(2)O(2) formation with different ions. Many of the trends in hydrogen peroxide yields with pH observed with γ-irradiations are observed with irradiation by the heavy ions. The lower yields of radicals in the homogeneous phase with the heavier ions tend to minimize the effects of radicals on the hydrogen peroxide yields at long times.

Simultaneous saccharification and fermentation of Eastern redcedar heartwood and sapwood using a novel size reduction technique.

PubMed

Ramachandriya, Karthikeyan D; Wilkins, Mark; Pardo-Planas, Oscar; Atiyeh, Hasan K; Dunford, Nurhan T; Hiziroglu, Salim

2014-06-01

This study investigated the effect of two wood zones (sapwood versus heartwood) and size reduction techniques [Crumbles® (Crumbles® is a registered trademark of Forest Concepts, LLC, Auburn, WA, USA) particles versus ground particles] on wood glucan-to-ethanol yield after acid bisulfite pretreatment and simultaneous saccharification and fermentation (SSF) of Eastern redcedar. SSFs were conducted at 8% solids loading (w/w dry basis) using Accellerase® 1500 at a loading of 46FPU/g glucan and Saccharomyces cerevisiae D5A for ethanol fermentation. The size reduction technique had no effect on ethanol yield. However, sapwood glucan-to-ethanol yields were significantly greater than heartwood yields. The highest wood glucan-to-ethanol yield of 187L/dryMg (95% of theoretical) was achieved with sapwood crumbled particles in 240h. Ground sapwood, crumbled heartwood and ground heartwood achieved ethanol yields of 89%, 81% and 80% of theoretical in 240h, respectively. Preliminary mass balances showed 100% glucan recovery with crumbled sapwood and extensive (72%) delignification. Copyright © 2014 Elsevier Ltd. All rights reserved.

Red cabbage yield, heavy metal content, water use and soil chemical characteristics under wastewater irrigation.

PubMed

Tunc, Talip; Sahin, Ustun

2016-04-01

The objective of this 2-year field study was to evaluate the effects of drip irrigation with urban wastewaters reclaimed using primary (filtration) and secondary (filtration and aeration) processes on red cabbage growth and fresh yield, heavy metal content, water use and efficiency and soil chemical properties. Filtered wastewater (WW1), filtered and aerated wastewater (WW2), freshwater and filtered wastewater mix (1:1 by volume) (WW3) and freshwater (FW) were investigated as irrigation water treatments. Crop evapotranspiration decreased significantly, while water use efficiency increased under wastewater treatments compared to FW. WW1 treatment had the lowest value (474.2 mm), while FW treatments had the highest value (556.7 mm). The highest water use efficiency was found in the WW1 treatment as 8.41 kg m(-3), and there was a twofold increase with regard to the FW. Wastewater irrigation increased soil fertility and therefore red cabbage yield. WW2 treatment produced the highest total fresh yield (40.02 Mg ha(-1)). However, wastewater irrigation increased the heavy metal content in crops and soil. Cd content in red cabbage heads was above the safe limit, and WW1 treatment had the highest value (0.168 mg kg(-1)). WW3 treatment among wastewater treatments is less risky in terms of soil and crop heavy metal pollution and faecal coliform contamination. Therefore, WW3 wastewater irrigation for red cabbage could be recommended for higher yield and water efficiency with regard to freshwater irrigation.

Effect of supercritical carbon dioxide on the enzymatic production of biodiesel from waste animal fat using immobilized Candida antarctica lipase B variant.

PubMed

Pollardo, Aldricho Alpha; Lee, Hong-Shik; Lee, Dohoon; Kim, Sangyong; Kim, Jaehoon

2017-09-09

Waste animal fat is a promising feedstock to replace vegetable oil that widely used in commercial biodiesel process, however the high content of free fatty acid in waste fat makes it unfeasible to be processed with commercial base-catalytic process. Enzymatic process is preferable to convert waste fat into biodiesel since enzyme can catalyze both esterification of free fatty acid and transesterification of triglyceride. However, enzymatic reaction still has some drawbacks such as lower reaction rates than base-catalyzed transesterification and the limitation of reactant concentration due to the enzyme inhibition of methanol. Supercritical CO 2 is a promising reaction media for enzyme-catalyzed transesterification to overcome those drawbacks. The transesterification of waste animal fat was carried out in supercritical CO 2 with varied concentration of feedstock and methanol in CO 2 . The CO 2 to feedstock mass ratio of 10:1 showed the highest yield compared to other ratios, and the highest FAME yield obtained from waste animal fat was 78%. The methanol concentration effect was also observed with variation 12%, 14%, and 16% of methanol to feedstock ratio. The best yield was 87% obtained at the CO 2 to feedstock ratio of 10: 1 and at the methanol to feedstock ratio of 14% after 6 h of reaction. Enzymatic transesterification to produce biodiesel from waste animal fat in supercritical fluid media is a potential method for commercialization since it could enhance enzyme activity due to supercritical fluid properties to remove mass transfer limitation. The high yield of FAME when using high mass ratio of CO 2 to oil showed that supercritical CO 2 could increase the reaction and mass transfer rate while reducing methanol toxicity to enzyme activity. The increase of methanol concentration also increased the FAME yield because it might shift the reaction equilibrium to FAME production. This finding describes that the application of supercritical CO 2 in the enzymatic reaction enables the application of simple process such as a packed-bed reactor.

Statistical key factors optimization of conditions for hydrogen production from S-TE (solubilization by thermophilic enzyme) waste sludge.

PubMed

Guo, Liang; Zhao, Jun; She, Zonglian; Lu, Mingmin; Zong, Yan

2013-06-01

Waste sludge can be solubilized after S-TE (solubilization by thermophilic enzyme) pretreatment as the cryptic growth occurs at the expense of the cell lysate. The hydrogen production from S-TE sludge is greatly influenced by many factors. In this study, factors including pH, C/N, C/P, and Fe(2+) affecting hydrogen production from S-TE sludge were optimized using uniform design. The optimum condition for maximum hydrogen yield of 68.4 ml H2/g VSS (volatile suspended solid) could be predicted from regression model, and the optimum conditions were pH of 6.4, C/N ratio of 38, C/P ratio of 265, and Fe(2+) concentration of 85 mg/L. There was interaction effect of factors on hydrogen production from S-TE sludge. Different pH, C/N, C/P and Fe(2+) conditions could influence the VSS removal rate, carbohydrate and protein utilization. When the highest compositions of acetate and ethanol and lowest propionate were observed in metabolites, effective hydrogen production was also achieved. Copyright © 2013 Elsevier Ltd. All rights reserved.

High level extracellular production of a recombinant alkaline catalase in E. coli BL21 under ethanol stress and its application in hydrogen peroxide removal after cotton fabrics bleaching.

PubMed

Yu, Zhenxiao; Zheng, Hongchen; Zhao, Xingya; Li, Shufang; Xu, Jianyong; Song, Hui

2016-08-01

The effects of induction parameters, osmolytes and ethanol stress on the productivity of the recombinant alkaline catalase (KatA) in Escherichia coli BL21 (pET26b-KatA) were investigated. The yield of soluble KatA was significantly enhanced by 2% ethanol stress. And a certain amount of Triton X-100 supplementation could markedly improved extracellular ratio of KatA. A total soluble catalase activity of 78,762U/mL with the extracellular ratio of 92.5% was achieved by fed-batch fermentation in a 10L fermentor, which was the highest yield so far. The purified KatA showed high stability at 50°C and pH 6-10. Application of KatA for elimination of H2O2 after cotton fabrics bleaching led to less consumption of water, steam and electric power by 25%, 12% and 16.7% respectively without productivity and quality losing of cotton fabrics. Thus, the recombinant KatA is a promising candidate for industrial production and applications. Copyright © 2016 Elsevier Ltd. All rights reserved.

Supply of avocado starch (Persea americana mill) as bioplastic material

NASA Astrophysics Data System (ADS)

Ginting, M. H. S.; Hasibuan, R.; Lubis, M.; Alanjani, F.; Winoto, F. A.; Siregar, R. C.

2018-02-01

The purpose of this study was to determine the effect of time precipitation of avocado slurry seed to yield of starch. Starch analysis included starch content, moisture content, amylose content, amylopectin content, ash content, protein content, fat content, Fourier transform infra red analysis and rapid visco analyzer. Supply of starch from avocado seeds was used by extraction method. Every one hundred grams of avocado slurry was precipitated by gravity with variations for 4 hours, 8 hours, 12 hours, 16 hours, 20 hours and 24 hours. The Starch yield was washed, and dried using oven at 70°C for 30 minutes. Starch yield was the highest as 24.20 gram at 24 hours. The result of starch characterization was 73.62%, water content 16.6%, amylose 0.07%, amylopectin 73.55%, ash content 0.23%, protein content 2.16%, fat content 1.09%. Rapid visco analyzer obtained at 91.33°C of gelatinization temperature. Scanning electron microscopy analyzes obtained 20 μm oval-shaped starch granules. Fourier Transform Infra Red analysis of starch obtained the peak spectrum of O-H group of alcohols, C-H alkanes and C-O ether.

Microwave-assisted extraction of three bioactive alkaloids from Peganum harmala L. and their acaricidal activity against Psoroptes cuniculi in vitro.

PubMed

Shang, Xiaofei; Guo, Xiao; Li, Bing; Pan, Hu; Zhang, Jiyu; Zhang, Yu; Miao, Xiaolou

2016-11-04

Peganum harmala L. is a perennial herbaceous, glabrous plant that grows in semi-arid conditions, steppe areas and sandy soils. It is used to treat fever, diarrhoea, subcutaneous tumours, arthralgia, rheumatism, cough, amnesia and parasitic diseases in folk medicines. In this paper, we aimed to develop a simpler and faster method for the extraction of three alkaloids from Peganum harmala L. than other conventional methods by optimizing the parameters of a microwave-assisted extraction (MAE) method, and to investigate the acaricidal activities of three compounds against Psoroptes cuniculi. After optimizing the operating parameters with the single factor experiment and a Box-Behnken design combined with a response-surface methodology, a MAE method was developed for extracting the alkaloids from the seeds, and a high-performance liquid chromatography was used to quantify these compounds. An in vitro experiments were used to study the acaricidal activities. The optimal conditions of MAE method were as follows: liquid-to-solid ratio 31.3:1mL/g, ethanol concentration 75.5%, extraction time 10.1min, temperature 80.7°C, and microwave power 600W. Compared to the heat reflux extraction (HRE, 60min) and the ultrasonic-assisted extraction (UAE, 30min) methods, MAE method require the shortest time (10min) and obtain the highest yield of three compounds (61.9mg/g). Meanwhile, the LT 50 values for the vasicine (1.25 and 2.5mg/mL), harmaline (1.25 and 2.5mg/mL), harmine (1.25 and 2.5mg/mL) and MAE extract (100mg/mL) against Psoroptes cuniculi were 12.188h, 9.791h, 11.994h, 10.095h, 11.293h, 9.273h and 17.322h, respectively. The MAE method developed exhibited the highest extraction yield within the shortest time and thus could be used to extract the active compounds from Peganum harmala L. on an industrial basis. As the active compounds of Peganum harmala L., vasicine, harmalin and harmine presented the marked acaricidal activities against Psoroptes cuniculi, and could be widely applied for the treatments of acariasis in animals. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Biosurfactant-enhanced hydrogen production from organic fraction of municipal solid waste using co-culture of E. coli and Enterobacter aerogenes.

PubMed

Sharma, Preeti; Melkania, Uma

2017-11-01

The effect of biosurfactants (surfactin and saponin) on the hydrogen production from organic fraction of municipal solid waste (OFMSW) was investigated using co-culture of facultative anaerobes Enterobacter aerogenes and E. coli. The biosurfactants were applied in the concentration ranges of 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5 and 5.0% each. Cumulative hydrogen production (P), maximum hydrogen production rate (Rmax) and lag phases (λ) were analyzed using modified Gompertz model. Results revealed that both the biosurfactants were effective in hydrogen production enhancement. The maximum cumulative hydrogen production of 743.5±14.4ml and 675.6±12.1ml and volumetric hydrogen production of 2.12L H2 /L substrate and 1.93L H2 /L substrate was recorded at 3.5% surfactin and 3.0% saponin respectively. Corresponding highest hydrogen yields were 79.2mlH 2 /gCarbo initial and 72.0mlH 2 /gCarbo initial respectively. Lag phase decreased from 12.5±2.0h at control to a minimum of 9.0±2.8h and 9.5±2.1h at 3.5% surfactin and 3.0% saponin respectively. Volatile fatty acid generation was increased with biosurfactants addition. Copyright © 2017 Elsevier Ltd. All rights reserved.

Measurement and significance of the equilibrium reaction C-13/+/ + /C-12/O yields C-12/+/ + /C-13/O for alteration of the C-13/C-12 ratio in interstellar molecules

NASA Technical Reports Server (NTRS)

Watson, W. D.; Anicich, V. G.; Huntress, W. T., Jr.

1976-01-01

Laboratory measurements using the ion-cyclotron resonance technique yield a rate constant of 2 by 10 to the -10th power cu cm/sec at 300 K for the isotope exchange C-13(+) + (C-12)O yields C-12(+) + (C-13)O. According to the usual ideas about ion-molecule reactions, this rate constant should also be appropriate at temperatures not exceeding about 100 K. Then the observed C-13/C-12 ratio obtained from radio observation of interstellar molecules may be either larger or smaller than the actual value in the interstellar medium by factors of 2 or so. If the ratio is altered from the actual interstellar value, it will not be the same in all molecules, and CO will tend to have the highest value. The chief astronomical uncertainty for the occurrence of this isotope fractionation is the abundance of 'unobservable' molecules which can react rapidly with C(+): e.g., O2, H2O, CO2, and CH4. If their abundance is greater than about one-tenth that of CO, the isotope fractionation will be inhibited.

The synthesis and characterization of 7-hydroxy-4-methylcoumarin and the investigation of the fluorescence properties of its 7-hydroxy-4-methylcoumarin-chitosan films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wahyuningrum, Deana, E-mail: deana@chem.itb.ac.id; Zulqarnaen, Muhammad; Suendo, Veinardi

Chitosan fluorescent films containing 7-hydroxy-4-methylcoumarin (7H4MC) have been successfully prepared. Used chitosan was obtained from chitin isolated from skin of tiger prawns (Penaeus monodon) through the deproteination, demineralization, and deacetylation process. The yields of chitin and chitosan are 10.66% and 23.83%, respectively. The chitosan has 55.00% degree of deacetylation based on FTIR spectroscopy. Average molecular mass of chitosan which was determined by Ostwald viscometry method is 8.55 × 10{sup 6} g/mol. The 7H4MC was synthesized from resorcinol and ethyl acetoacetate using amberlyst-15 as catalyst based on Pechmann reaction with chemical yields of 90.01% and the melting point of 189–190°C. Themore » FTIR, {sup 1}H–NMR, and {sup 13}C–NMR spectroscopies confirmed the structure which corresponds to the structure of 7H4MC. The films of chitosan containing 7H4MC were prepared by solvent evaporation method in 2% (v/v) acetic acid. The 7H4MC content in each film was 0% (blank), 0.2%, 0.4%, 0.6%, and 0.8% (w/w). The UV-Vis spectrum of 7H4MC in methanol showed λ{sub max} at 235 and 337 nm. The observed fluorescence is the fluorescence color of cyan. The excitation wavelengths are 200, 235, 275, 337, and 365 nm. The highest intensity of cyan color fluorescence of chitosan containing 7H4MC films was obtained at the concentration of 0.2% of 7-hydroxy-4-methylcoumarin at the excitation wavelength of 275 nm.« less

Sequential Elution of Essential Oil Constituents during Steam Distillation of Hops (Humulus lupulus L.) and Influence on Oil Yield and Antimicrobial Activity.

PubMed

Jeliazkova, Ekaterina; Zheljazkov, Valtcho D; Kačániova, Miroslava; Astatkie, Tess; Tekwani, Babu L

2018-06-07

The profile and bioactivity of hops (Humulus lupulus L.) essential oil, a complex natural product extracted from cones via steam distillation, depends on genetic and environmental factors, and may also depend on extraction process. We hypothesized that compound mixtures eluted sequentially and captured at different timeframes during the steam distillation process of whole hop cones would have differential chemical and bioactivity profiles. The essential oil was collected sequentially at 8 distillation time (DT) intervals: 0-2, 2-5, 5-10, 10-30, 30-60, 60-120, 120-180, and 180-240 min. The control was a 4-h non-interrupted distillation. Nonlinear regression models described the DT and essential oil compounds relationship. Fractions yielded 0.035 to 0.313% essential oil, while control yielded 1.47%. The oil eluted during the first hour was 83.2%, 9.6% during the second hour, and only 7.2% during the second half of the distillation. Essential oil (EO) fractions had different chemical profile. Monoterpenes were eluted early, while sequiterpenes were eluted late. Myrcene and linalool were the highest in 0-2 min fraction, β-caryophyllene, β-copaene, β-farnesene, and α-humulene were highest in fractions from middle of distillation, whereas α- bergamotene, γ-muurolene, β- and α-selinene, γ- and δ-cadinene, caryophyllene oxide, humulne epoxide II, τ-cadinol, and 6-pentadecen-2-one were highest in 120-180 or 180-240 min fractions. The Gram-negative Escherichia coli was strongly inhibited by essential oil fractions from 2-5 min and 10-30 min, followed by oil fraction from 0-2 min. The strongest inhibition activity against Gram-negative Yersinia enterocolitica, and Gram-positive Clostridium perfringens, Enterococcus faecalis, and Staphylococcus aureus subs. aureus was observed with the control essential oil. This is the first study to describe significant activity of hops essential oils against Trypanosoma brucei, a parasitic protozoan that causes African trypanosomiasis (sleeping sickness in humans and nagana in other animals). Hops essential oil fractions or whole oil may be used as antimicrobial agents or for the development of new drugs.

Degradation of 2-chloroallylalcohol by a Pseudomonas sp.

PubMed Central

van der Waarde, J J; Kok, R; Janssen, D B

1993-01-01

Three Pseudomonas strains capable of utilizing 2-chloroallylalcohol (2-chloropropenol) as the sole carbon source for growth were isolated from soil. The fastest growth was observed with strain JD2, with a generation time of 3.6 h. Degradation of 2-chloroallylalcohol was accompanied by complete dehalogenation. Chloroallylalcohols that did not support growth were dechlorinated by resting cells; the dechlorination level was highest if an alpha-chlorine substituent was present. Crude extracts of strain JD2 contained inducible alcohol dehydrogenase activity that oxidized mono- and dichloroallylalcohols but not trichloroallylalcohol. The enzyme used phenazine methosulfate as an artificial electron acceptor. Further oxidation yielded 2-chloroacrylic acid. The organism also produced hydrolytic dehalogenases converting 2-chloroacetic acid and 2-chloropropionic acid. PMID:8434917

Conversion of secondary pulp/paper sludge powder to liquid oil products for energy recovery by direct liquefaction in hot-compressed water.

PubMed

Xu, Chunbao; Lancaster, Jody

2008-03-01

The present work demonstrated that secondary pulp/paper sludge powder, with a higher heating value of 18.3MJ/kg on a dry basis, could be effectively converted into liquid oil products by direct liquefaction in hot-compressed water with and without catalyst. Treatments of secondary pulp/paper sludge in water at 250-380 degrees C for 15-120min in the presence of N(2) atmosphere resulted in yields of water-soluble oils at 20-45wt% and yields of heavy oils at 15-25wt%, with higher heating values of 10-15 and >35MJ/kg, respectively. The higher caloric values for the heavy oil products were accounted for by their compositions of long-chain carboxylic acids, heterocyclic nitrogen compounds and phenolic compounds and derivatives as evidenced by the gas chromatograph (GC)/MS measurements. The liquefaction product yields were significantly influenced by the liquefaction temperature, the residence time, the initial biomass concentration, catalysts and the liquefaction atmosphere (inert or reducing). Within the temperature range (250-380 degrees C) tested, the lowest temperature produced the highest yield of total oils (at 60wt%), while the greatest yield of heavy oil (at about 24wt%) was obtained at 350 degrees C. If the temperature was fixed at 280 degrees C, a greater yield of heavy oil (reaching as high as 25wt% for 120min) was obtained as the length of reaction time increased. Similarly, a higher initial biomass concentration produced a greater yield of heavy oil but a reduced yield of water-soluble oil. The presence of 0.1M K(2)CO(3) dramatically enhanced organic conversion, but suppressed the formation of both heavy oil and water-soluble oil. The use of the two alkaline earth metal catalysts, i.e., Ca(OH)(2) and Ba(OH)(2), did not alter organic conversion, but it catalyzed the formation of water-soluble oil and produced higher yields of total oil products. It was also demonstrated that the reducing atmosphere (i.e., H(2)) in the liquefaction process promoted the heavy oil formation while suppressing the water-soluble oil formation. With the presence of 0.1M Ca(OH)(2) and 2MPa H(2), liquefaction of the sludge powder in water at 280 degrees C for 60min produced a higher yield of heavy oil (26wt%), almost two times as high as that in N(2) (13.6wt%), resulting in a greater net energy efficiency. It was thus suggested that direct liquefaction of secondary pulp/paper sludge in hot-compressed water with Ca(OH)(2) catalyst and in the presence of H(2) could be an effective approach to recovering energy from the waste for production of liquid oil products.

The effect of the labile organic fraction in food waste and the substrate/inoculum ratio on anaerobic digestion for a reliable methane yield.

PubMed

Kawai, Minako; Nagao, Norio; Tajima, Nobuaki; Niwa, Chiaki; Matsuyama, Tatsushi; Toda, Tatsuki

2014-04-01

Influence of the labile organic fraction (LOF) on anaerobic digestion of food waste was investigated in different S/I ratio of 0.33, 0.5, 1.0, 2.0 and 4.0g-VSsubstrate/g-VSinoculum. Two types of substrate, standard food waste (Substrate 1) and standard food waste with the supernatant (containing LOF) removed (Substrate 2) were used. Highest methane yield of 435ml-CH4g-VS(-1) in Substrate 1 was observed in the lowest S/I ratio, while the methane yield of the other S/I ratios were 38-73% lower than the highest yield due to acidification. The methane yields in Substrate 2 were relatively stable in all S/I conditions, although the maximum methane yield was low compared with Substrate 1. These results showed that LOF in food waste causes acidification, but also contributes to high methane yields, suggesting that low S/I ratio (<0.33) is required to obtain a reliable methane yield from food waste compared to other organic substrates. Copyright © 2014 Elsevier Ltd. All rights reserved.

A rational approach to improving productivity in recombinant Pichia pastoris fermentation.

PubMed

d'Anjou, M C; Daugulis, A J

2001-01-05

A Mut(S) Pichia pastoris strain that had been genetically modified to produce and secrete sea raven antifreeze protein was used as a model system to demonstrate the implementation of a rational, model-based approach to improve process productivity. A set of glycerol/methanol mixed-feed continuous stirred-tank reactor (CSTR) experiments was performed at the 5-L scale to characterize the relationship between the specific growth rate and the cell yield on methanol, the specific methanol consumption rate, the specific recombinant protein formation rate, and the productivity based on secreted protein levels. The range of dilution rates studied was 0. 01 to 0.10 h(-1), and the residual methanol concentration was kept constant at approximately 2 g/L (below the inhibitory level). With the assumption that the cell yield on glycerol was constant, the cell yield on methanol increased from approximately 0.5 to 1.5 over the range studied. A maximum specific methanol consumption rate of 20 mg/g. h was achieved at a dilution rate of 0.06 h(-1). The specific product formation rate and the volumetric productivity based on product continued to increase over the range of dilution rates studied, and the maximum values were 0.06 mg/g. h and 1.7 mg/L. h, respectively. Therefore, no evidence of repression by glycerol was observed over this range, and operating at the highest dilution rate studied maximized productivity. Fed-batch mass balance equations, based on Monod-type kinetics and parameters derived from data collected during the CSTR work, were then used to predict cell growth and recombinant protein production and to develop an exponential feeding strategy using two carbon sources. Two exponential fed-batch fermentations were conducted according to the predicted feeding strategy at specific growth rates of 0.03 h(-1) and 0.07 h(-1) to verify the accuracy of the model. Cell growth was accurately predicted in both fed-batch runs; however, the model underestimated recombinant product concentration. The overall volumetric productivity of both runs was approximately 2.2 mg/L. h, representing a tenfold increase in the productivity compared with a heuristic feeding strategy. Copyright 2001 John Wiley & Sons, Inc.

Harvesting of freshwater microalgae biomass by Scenedesmus sp. as bioflocculant

NASA Astrophysics Data System (ADS)

Rinanti, A.; Purwadi, R.

2018-01-01

This study is particularly expected to provide information on the diversity of microalgae as the flocculant agent that gives the highest biomass yield. Bioflocculation was done by using one of the flocculating microalgae i.e. Scenedesmus obliquus to concentrate on non-flocculating microalgae Chlorella vulgaris. The freshwater microalgae S. obliquus tested it ability to harvest other non-flocculating microalgae, increased sedimentation rate in the flocculation process and increased biomass yield. The flocculation of biomass microalgae with chemical flocculant as comparison was done by adding alum (K2SO4·Al2 (SO4)3·24H2O). The addition of alum (K2SO4·Al2 (SO4)3·24H2O) as flocculant at pH 11 and S. obliquus sp. as bioflocculant caused significant alteration of nutrition of microalgae. Overall, the essential content produced by flocculation method with addition of alum or with bioflocculation (%, mg/100 mg dry weight) are lipid 31,64; 38,69, protein 30,79; 38.50%, and chlorophyll 0.6253; 0.8420). Harvesting with bioflocculation methods conducted at the end of the cultivation period increase the amount of biomass significantly and can accelerate the settling time of biomass. Harvesting microalgae cells by bioflocculation method becomes an economically competitive harvesting method compared to alum as a chemical flocculant because of the cheaper cost of flocculant, not toxic so it does not require further water treatment after harvesting due to the use of alum as chemical flocculants.

Electron-stimulated reactions in nanoscale water films adsorbed on (alpha)-Al2O3(0001)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Petrik, Nikolay G.; Kimmel, Gregory A.

2018-05-11

The radiation-induced decomposition and desorption of nanoscale amorphous solid water (D2O) films adsorbed on -Al2O3(0001) surface was studied at low temperature in ultrahigh vacuum using temperature programmed desorption (TPD) and electron stimulated desorption (ESD) with a mono-energetic, low energy electron source. ESD yields of molecular products ( D2, O2 and D¬2O) and the total sputtering yield increased with increasing D2O coverage up to ~15 water monolayers (i.e. ~15 1015 cm-2) to a coverage-independent level for thicker water films. Experiments with isotopically-layered water films (D2O and H2O) demonstrated that the highest water decomposition yields occurred at the interfaces of the nanoscalemore » water films with the alumina substrate and vacuum. However, the increased reactivity of the water/alumina interface is relatively small compared to the enhancements in the non-thermal reactions previously observed at the water/Pt(111) and water/TiO2(110) interfaces. We propose that the relatively low activity of Al2O3(0001) for the radiation-induced production of molecular hydrogen is associated with lower reactivity of this surface with hydrogen atoms, which are likely precursors for the molecular hydrogen.« less

Electron-stimulated reactions in nanoscale water films adsorbed on α-Al 2 O 3 (0001)

DOE PAGES

Petrik, Nikolay G.; Kimmel, Greg A.

2018-04-11

The radiation-induced decomposition and desorption of nanoscale amorphous solid water (D 2O) films adsorbed on an α-Al 2O 3(0001) surface was studied at low temperature in ultrahigh vacuum using temperature programmed desorption (TPD) and electron stimulated desorption (ESD) with a mono-energetic, low energy electron source. ESD yields of molecular products (D 2, O 2 and D 2O) and the total sputtering yield increased with increasing D 2O coverage up to ~15 water monolayers (i.e. ~15 x 10 15 cm -2) to a coverage-independent level for thicker water films. Experiments with isotopically-layered water films (D 2O and H 2O) demonstrated thatmore » the highest water decomposition yields occurred at the interfaces of the nanoscale water films with the alumina substrate and vacuum. However, the increased reactivity of the water/alumina interface is relatively small compared to the enhancements in the non-thermal reactions previously observed at the water/Pt(111) and water/TiO 2(110) interfaces. Here, we propose that the relatively low activity of Al 2O 3(0001) for the radiation-induced production of molecular hydrogen is associated with lower reactivity of this surface with hydrogen atoms, which are likely precursors for the formation of molecular hydrogen.« less

Electron-stimulated reactions in nanoscale water films adsorbed on α-Al 2 O 3 (0001)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Petrik, Nikolay G.; Kimmel, Greg A.

The radiation-induced decomposition and desorption of nanoscale amorphous solid water (D 2O) films adsorbed on an α-Al 2O 3(0001) surface was studied at low temperature in ultrahigh vacuum using temperature programmed desorption (TPD) and electron stimulated desorption (ESD) with a mono-energetic, low energy electron source. ESD yields of molecular products (D 2, O 2 and D 2O) and the total sputtering yield increased with increasing D 2O coverage up to ~15 water monolayers (i.e. ~15 x 10 15 cm -2) to a coverage-independent level for thicker water films. Experiments with isotopically-layered water films (D 2O and H 2O) demonstrated thatmore » the highest water decomposition yields occurred at the interfaces of the nanoscale water films with the alumina substrate and vacuum. However, the increased reactivity of the water/alumina interface is relatively small compared to the enhancements in the non-thermal reactions previously observed at the water/Pt(111) and water/TiO 2(110) interfaces. Here, we propose that the relatively low activity of Al 2O 3(0001) for the radiation-induced production of molecular hydrogen is associated with lower reactivity of this surface with hydrogen atoms, which are likely precursors for the formation of molecular hydrogen.« less

Ultrasound-assisted extraction of pectins from grape pomace using citric acid: a response surface methodology approach.

PubMed

Minjares-Fuentes, R; Femenia, A; Garau, M C; Meza-Velázquez, J A; Simal, S; Rosselló, C

2014-06-15

An ultrasound-assisted procedure for the extraction of pectins from grape pomace with citric acid as the extracting agent was established. A Box-Behnken design (BBD) was employed to optimize the extraction temperature (X1: 35-75°C), extraction time (X2: 20-60 min) and pH (X3: 1.0-2.0) to obtain a high yield of pectins with high average molecular weight (MW) and degree of esterification (DE) from grape pomace. Analysis of variance showed that the contribution of a quadratic model was significant for the pectin extraction yield and for pectin MW whereas the DE of pectins was more influenced by a linear model. An optimization study using response surface methodology was performed and 3D response surfaces were plotted from the mathematical model. According to the RSM model, the highest pectin yield (∼32.3%) can be achieved when the UAE process is carried out at 75°C for 60 min using a citric acid solution of pH 2.0. These pectic polysaccharides, composed mainly by galacturonic acid units (<97% of total sugars), have an average MW of 163.9 kDa and a DE of 55.2%. Close agreement between experimental and predicted values was found. These results suggest that ultrasound-assisted extraction could be a good option for the extraction of functional pectins with citric acid from grape pomace at industrial level. Copyright © 2014 Elsevier Ltd. All rights reserved.

Fluorene-Based Conjugated Microporous Polymers: Preparation and Chemical Sensing Application.

PubMed

Zhang, Qiujing; Yu, Sen; Wang, Qian; Xiao, Qin; Yue, Yong; Ren, Shijie

2017-12-01

Conjugated microporous polymers (CMPs) with strong fluorescence are great candidates for optoelectronic applications such as photocatalysis and chemical sensing. A series of novel fluorene-based conjugated microporous polymers (FCMPs) with different electronic structures are prepared by Yamamoto coupling reactions using rationally designed monomers. The FCMPs show a high degree of microporosity, decent specific surface areas, and variable fluorescence. FCMP3, which possesses a triazine knot in the network, exhibits the highest specific surface area of 489 m 2 g -1 , the largest pore volume of 0.30 cm 3 g -1 , and the highest solid-state photoluminescence quantum yield of 11.46%. Chemical sensing performance of FCMPs is studied using a range of nitroaromatic compounds as the analytes. Among the FCMPs, FCMP3 exhibits the highest Stern-Volmer constants of 2541, 4708, and 5241 m -1 for the detection of nitrobenzene, 4-nitrotoluene, 2,4-dinitrotoluene, respectively, which are comparable to the detecting efficiency of the state-of-the-art CMP-based sensing agents. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Simultaneous Production and Recovery of Fumaric Acid from Immobilized Rhizopus oryzae with a Rotary Biofilm Contactor and an Adsorption Column

PubMed Central

Cao, N.; Du, J.; Gong, C. S.; Tsao, G. T.

1996-01-01

An integrated system of simultaneous fermentation-adsorption for the production and recovery of fumaric acid from glucose by Rhizopus oryzae was investigated. The system was constructed such that growing Rhizopus mycelia were self-immobilized on the plastic discs of a rotary biofilm contactor during the nitrogen-rich growth phase. During the nongrowth, production phase, the biofilm was alternately exposed to liquid medium and air upon rotation of the discs in the horizontal fermentation vessel. The product of fermentation, fumaric acid, was removed simultaneously and continuously by a coupled adsorption column, thereby moderating inhibition, enhancing the fermentation rate, and sustaining cell viability. Another beneficial effect of the removal of fumaric acid is release of hydroxyl ions from a polyvinyl pyridine adsorbent into the circulating fermentation broth. This moderates the decrease in pH that would otherwise occur. Polyvinyl pyridine and IRA-900 gave the highest loading for this type of fermentation. This fermentation system is capable of producing fumaric acid with an average yield of 85 g/liter from 100 g of glucose per liter within 20 h under repetitive fed-batch cycles. On a weight yield basis, 91% of the theoretical maximum was obtained with a productivity of 4.25 g/liter/h. This is in contrast to stirred-tank fermentation supplemented with calcium carbonate, whose average weight yield was 65% after 72 h with a productivity of 0.9 g/liter/h. The immobilized reactor was operated repetitively for 2 weeks without loss of biological activity. PMID:16535381

A Phenylurea Cytokinin, CPPU, Elevated Reducing Sugar and Correlated to Andrographolide Contents in Leaves of Andrographis paniculata (Burm. F.) Wall. Ex Nees.

PubMed

Worakan, Phapawee; Karaket, Netiya; Maneejantra, Nuchada; Supaibulwatana, Kanyaratt

2017-02-01

Cytokinins are phytohormones that play multiple roles to control plant growth and development. In this study, leaf biomass and the production of andrographolide compounds in a medicinal plant Andrographis paniculata were significantly increased after exogenously treating with the synthetic cytokinin cytokinin-1-(2-chloro-4-pyridyl)-3-phenylurea (CPPU) at 0 (water), 5, or 10 mg L -1 and observed the results for 24 h, 48 h, and 7 days of treatment. It was found that CPPU could significantly enhance new axillary bud formation and further promote branching 4.6-5.6-fold higher, resulting in higher fresh weight (FW) and dry weight (DW) than the control. Application of CPPU at 5 mg L -1 significantly promoted the highest contents of total reducing sugar at 2.5-fold in leaves and at 1.5-fold in roots. Although treatments of CPPU significantly affected the increasing contents of chlorophyll and carotenoid (1.2-1.6-fold), CPPU at 10 mg L -1 slightly caused leaf stress and chlorophyll reduction. Interestingly, 5 mg L -1 CPPU could enhance andrographolide content, an active anti-infectious compound in Andrographis paniculata (2.2-fold higher than the control) that reached the highest content at 24 h after treatment. This study suggested that CPPU should be suitable for field application to promote leaf yields and induce the production of useful pharmaceutical compounds in Andrographis paniculata.

Optimized Extraction of Resveratrol from Arachis repens Handro by Ultrasound and Microwave: A Correlation Study with the Antioxidant Properties and Phenol Contents

PubMed Central

Garcia, Leonardo; Garcia, Renata; Sutili, Felipe; Souza, Rodrigo De

2016-01-01

The vegetal species Arachis repens, commonly known as peanut grass, was studied and, for the first time, we detected the presence of the bioactive compound trans-resveratrol (t-RSV). We compared the efficiency of three different methodologies (conventional maceration [CM], ultrasound-assisted extractions [UAE], and microwave-assisted extractions [MAE]) concerning total phenolics (TP) and resveratrol (t-RSV) content, followed by antioxidant activity (AA) evaluation. By CM, at 1 h, the highest RSV content (1.024 ± 0.036 mg/L) and, correspondingly, the highest DPPH capture (23.90 ± 0.04%) were found. The TP contents, at 1 h, presented the highest value (27.26 ± 0.26 mg/g GAE). By the UAE, the maximum yields of TP (357.18 mg/g GAE) and RSV (2.14 mg/L), as well as, the highest AA (70.95%), were obtained by 5 min after a maceration pretreatment, on the solid-solvent ratio 1 : 40 w/v. For MAE, a central composite rotatable design (CCRD) was applied followed by the FFD design in order to evaluate the statistical effects of four independent variables on the extraction of RSV. The optimal conditions established for obtaining the highest recovery (2.516 mg/g) were 20 min; 90% MeOH aq.; 120 rpm; 60°C; and solid-solvent ratio: 1 : 35 w/v. Relevant correlations were established considering the TP and RSV contents, as well as the AA, corroborating obvious advantages of such techniques in terms of high extraction efficiency in shorter times. PMID:28116343

Optimized Extraction of Resveratrol from Arachis repens Handro by Ultrasound and Microwave: A Correlation Study with the Antioxidant Properties and Phenol Contents.

PubMed

Garcia, Leonardo; Garcia, Renata; Pacheco, Georgia; Sutili, Felipe; Souza, Rodrigo De; Mansur, Elisabeth; Leal, Ivana

2016-01-01

The vegetal species Arachis repens , commonly known as peanut grass, was studied and, for the first time, we detected the presence of the bioactive compound trans- resveratrol ( t -RSV). We compared the efficiency of three different methodologies (conventional maceration [CM], ultrasound-assisted extractions [UAE], and microwave-assisted extractions [MAE]) concerning total phenolics (TP) and resveratrol ( t -RSV) content, followed by antioxidant activity (AA) evaluation. By CM, at 1 h, the highest RSV content (1.024 ± 0.036 mg/L) and, correspondingly, the highest DPPH capture (23.90 ± 0.04%) were found. The TP contents, at 1 h, presented the highest value (27.26 ± 0.26 mg/g GAE). By the UAE, the maximum yields of TP (357.18 mg/g GAE) and RSV (2.14 mg/L), as well as, the highest AA (70.95%), were obtained by 5 min after a maceration pretreatment, on the solid-solvent ratio 1 : 40 w/v. For MAE, a central composite rotatable design (CCRD) was applied followed by the FFD design in order to evaluate the statistical effects of four independent variables on the extraction of RSV. The optimal conditions established for obtaining the highest recovery (2.516 mg/g) were 20 min; 90% MeOH aq.; 120 rpm; 60°C; and solid-solvent ratio: 1 : 35 w/v. Relevant correlations were established considering the TP and RSV contents, as well as the AA, corroborating obvious advantages of such techniques in terms of high extraction efficiency in shorter times.

Enhanced production of natural yellow pigments from Monascus purpureus by liquid culture: The relationship between fermentation conditions and mycelial morphology.

PubMed

Lv, Jun; Zhang, Bo-Bo; Liu, Xiao-Dong; Zhang, Chan; Chen, Lei; Xu, Gan-Rong; Cheung, Peter Chi Keung

2017-10-01

Natural yellow pigments produced by submerged fermentation of Monascus purpureus have potential economic value and application in the food industry. In the present study, the relationships among fermentation conditions (in terms of pH and shaking/agitation speed), mycelial morphology and the production of Monascus yellow pigments were investigated in both shake-flask and scale-up bioreactor experiments. In the shake-flask fermentation, the highest yield of the Monascus yellow pigments was obtained at pH 5.0 and a shaking speed of 180 rpm. Microscopic images revealed that these results were associated with the formation of freely dispersed small mycelial pellets with shorter, thicker and multi-branched hyphae. Further investigation indicated that the hyphal diameter was highly correlated with the biosynthesis of the Monascus yellow pigments. In a scaled-up fermentation experiment, the yield of yellow pigments (401 U) was obtained in a 200-L bioreactor, which is the highest yield to the best of our knowledge. The present findings can advance our knowledge on the conditions used for enhancing the production of Monascus yellow pigments in submerged fermentation and facilitate large-scale production of these natural pigments. Copyright © 2017 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Effect of bioconversion conditions on vanillin production by Amycolatopsis sp. ATCC 39116 through an analysis of competing by-product formation.

PubMed

Ma, Xiao-kui; Daugulis, Andrew J

2014-05-01

This study investigated the effects of transformation conditions such as initial pH, the initial concentration of glucose and yeast extract in the medium, and the separate addition of ferulic acid and vanillic acid, on the production of vanillin through an analysis of competing by-product formation by Amycolatopsis sp. ATCC 39116. The extent and nature of by-product formation and vanillin yield were affected by initial pH and different initial concentrations of glucose and yeast extract in the medium, with a high yield of vanillin and high cell density obtained at pH 8.0, 10 g/l glucose, and 8 g/l yeast extract. High concentrations of ferulic acid were found to negatively affect cell density. Additional supplementation of 100 mg/l vanillic acid, a metabolically linked by-product, was found to result in a high concentration of vanillin and guaiacol, an intermediate of vanillin. Via an analysis of the effect of these transformation conditions on competing by-product formation, high concentrations of ferulic acid were transformed with a molar yield to vanillin of 96.1 and 95.2 %, by Amycolatopsis sp. ATCC 39116 and Streptomyces V1, respectively, together with a minor accumulation of by-products. These are among the highest performance values reported in the literature to date for Streptomyces in batch cultures.

Raman spectra from very concentrated aqueous NaOH and from wet and dry, solid, and anhydrous molten, LiOH, NaOH, and KOH.

PubMed

Walrafen, George E; Douglas, Rudolph T W

2006-03-21

High-temperature, high-pressure Raman spectra were obtained from aqueous NaOH solutions up to 2NaOHH2O, with X(NaOH)=0.667 at 480 K. The spectra corresponding to the highest compositions, X(NaOH)> or =0.5, are dominated by H3O2-. An IR xi-function dispersion curve for aqueous NaOH, at 473 K and 1 kbar, calculated from the data of Franck and Charuel indicates that the OH- ion forms H3O2- by preferential H bonding with nonhydrogen-bonded OH groups. Raman spectra from wet to anhydrous, solid LiOH, NaOH, and KOH yield sharp, symmetric OH- stretching peaks at 3664, 3633, and 3596 cm(-1), respectively, plus water-related, i.e., H3O2-, peaks near LiOH, 3562 cm(-1), NaOH, 3596 cm(-1), and, KOH, 3500 cm(-1). Absence of H3O2- peaks from the solid assures that the corresponding melt is anhydrous. Raman spectra from the anhydrous melts yield OH- stretching peak frequencies: LiOH, 3614+/-4 cm(-1), 873 K; NaOH, 3610+/-2 cm(-1), 975 K; and, KOH, 3607+/-2 cm(-1), 773 K, but low-frequency asymmetry due to ion-pair interactions is present which is centered near 3550 cm(-1). The ion-pair-related asymmetry corresponds to the sole IR maximum near 3550 cm(-1) from anhydrous molten NaOH, at 623 K. Bose-Einstein correction of published low-frequency Raman data from molten LiOH revealed an acoustic phonon, near 205 cm(-1), related to restricted translation of OH- versus Li+, and an optical phonon, at 625 cm(-1) and tau approximately 0.05 ps, due to protonic precession and/or pendular motion. Strong H bonding between water and the O atom of OH- forms H3O2-, but the proton of OH- does not bond with H significantly. Large Raman bandwidths (aqueous solutions) are explained in terms of inhomogeneous broadening due to proton transfer in a double well. Vibrational assignments are presented for H3O2-.

Influence of the Extractive Method on the Recovery of Phenolic Compounds in Different Parts of Hymenaea martiana Hayne

PubMed Central

Oliveira, Fernanda Granja da Silva; de Lima-Saraiva, Sarah Raquel Gomes; Oliveira, Ana Paula; Rabêlo, Suzana Vieira; Rolim, Larissa Araújo; Almeida, Jackson Roberto Guedes da Silva

2016-01-01

Background: Popularly known as “jatobá,” Hymenaea martiana Hayne is a medicinal plant widely used in the Brazilian Northeast for the treatment of various diseases. Objective: The aim of this study was to evaluate the influence of different extractive methods in the production of phenolic compounds from different parts of H. martiana. Materials and Methods: The leaves, bark, fruits, and seeds were dried, pulverized, and submitted to maceration, ultrasound, and percolation extractive methods, which were evaluated for yield, visual aspects, qualitative phytochemical screening, phenolic compound content, and total flavonoids. Results: The highest results of yield were obtained from the maceration of the leaves, which may be related to the contact time between the plant drug and solvent. The visual aspects of the extracts presented some differences between the extractive methods. The phytochemical screening showed consistent data with other studies of the genus. Both the vegetal part as the different extractive methods influenced significantly the levels of phenolic compounds, and the highest content was found in the maceration of the barks, even more than the content found previously. No differences between the levels of total flavonoids were significant. The highest concentration of total flavonoids was found in the ultrasound of the barks, followed by maceration on this drug. According to the results, the barks of H. martiana presented the highest total flavonoid contents. Conclusion: The results demonstrate that both the vegetable and the different extractive methods influenced significantly various parameters obtained in the various extracts, demonstrating the importance of systematic comparative studies for the development of pharmaceuticals and cosmetics. SUMMARY The phytochemical screening showed consistent data with other studies of the genus HymenaeaBoth the vegetable part and the different extractive methods influenced significantly various parameters obtained in the various extracts, including the levels of phenolic compoundsThe barks of H. martiana presented the highest total phenolic and flavonoid contents. PMID:27695267

Aqueous Biphasic Systems for the Synthesis of Formates by Catalytic CO2 Hydrogenation: Integrated Reaction and Catalyst Separation for CO2 -Scrubbing Solutions.

PubMed

Scott, Martin; Blas Molinos, Beatriz; Westhues, Christian; Franciò, Giancarlo; Leitner, Walter

2017-03-22

Aqueous biphasic systems were investigated for the production of formate-amine adducts by metal-catalyzed CO 2 hydrogenation, including typical scrubbing solutions as feedstocks. Different hydrophobic organic solvents and ionic liquids could be employed as the stationary phase for cis-[Ru(dppm) 2 Cl 2 ] (dppm=bis-diphenylphosphinomethane) as prototypical catalyst without any modification or tagging of the complex. The amines were found to partition between the two phases depending on their structure, whereas the formate-amine adducts were nearly quantitatively extracted into the aqueous phase, providing a favorable phase behavior for the envisaged integrated reaction/separation sequence. The solvent pair of methyl isobutyl carbinol (MIBC) and water led to the most practical and productive system and repeated use of the catalyst phase was demonstrated. The highest single batch activity with a TOF av of approximately 35 000 h -1 and an initial TOF of approximately 180 000 h -1 was achieved in the presence of NEt 3 . Owing to higher stability, the highest productivities were obtained with methyl diethanolamine (Aminosol CST 115) and monoethanolamine (MEA), which are used in commercial scale CO 2 -scrubbing processes. Saturated aqueous solutions (CO 2 overpressure 5-10 bar) of MEA could be converted into the corresponding formate adducts with average turnover frequencies up to 14×10 3  h -1 with an overall yield of 70 % based on the amine, corresponding to a total turnover number of 150 000 over eleven recycling experiments. This opens the possibility for integrated approaches to carbon capture and utilization. © 2017 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Electrostatic Self-Assembled Chitosan-Pectin Nano- and Microparticles for Insulin Delivery.

PubMed

Maciel, Vinicius B V; Yoshida, Cristiana M P; Pereira, Susana M S S; Goycoolea, Francisco M; Franco, Telma T

2017-10-12

A polyelectrolyte complex system of chitosan-pectin nano- and microparticles was developed to encapsulate the hormone insulin. The aim of this work was to obtain small particles for oral insulin delivery without chemical crosslinkers based on natural and biodegradable polysaccharides. The nano- and microparticles were developed using chitosans (with different degrees of acetylation: 15.0% and 28.8%) and pectin solutions at various charge ratios (n⁺/n - given by the chitosan/pectin mass ratio) and total charge. Nano- and microparticles were characterized regarding particle size, zeta potential, production yield, encapsulation efficiency, stability in different media, transmission electron microscopy and cytotoxicity assays using Caco-2 cells. The insulin release was evaluated in vitro in simulated gastric and intestinal media. Small-sized particles (~240-~1900 nm) with a maximum production yield of ~34.0% were obtained. The highest encapsulation efficiency (~62.0%) of the system was observed at a charge ratio (n⁺/n - ) 5.00. The system was stable in various media, particularly in simulated gastric fluid (pH 1.2). Transmission electron microscopy (TEM) analysis showed spherical shape particles when insulin was added to the system. In simulated intestinal fluid (pH 6.8), controlled insulin release occurred over 2 h. In vitro tests indicated that the proposed system presents potential as a drug delivery for oral administration of bioactive peptides.

QTL mapping of root traits in phosphorus-deficient soils reveals important genomic regions for improving NDVI and grain yield in barley.

PubMed

Gong, Xue; McDonald, Glenn

2017-09-01

Major QTLs for root rhizosheath size are not correlated with grain yield or yield response to phosphorus. Important QTLs were found to improve phosphorus efficiency. Root traits are important for phosphorus (P) acquisition, but they are often difficult to characterize and their breeding values are seldom assessed under field conditions. This has shed doubts on using seedling-based criteria of root traits to select and breed for P efficiency. Eight root traits were assessed under controlled conditions in a barley doubled-haploid population in soils differing in P levels. The population was also phenotyped for grain yield, normalized difference vegetation index (NDVI), grain P uptake and P utilization efficiency at maturity (PutE GY ) under field conditions. Several quantitative traits loci (QTLs) from the root screening and the field trials were co-incident. QTLs for root rhizosheath size and root diameter explained the highest phenotypic variation in comparison to QTLs for other root traits. Shared QTLs were found between root diameter and grain yield, and total root length and PutE GY . A common major QTL for rhizosheath size and NDVI was mapped to the HvMATE gene marker on chromosome 4H. Collocations between major QTLs for NDVI and grain yield were detected on chromosomes 6H and 7H. When results from BIP and MET were combined, QTLs detected for grain yield were also those QTLs found for NDVI. QTLs qGY5H, qGY6H and qGY7Hb on 7H were robust QTLs in improving P efficiency. A selection of multiple loci may be needed to optimize the breeding outcomes due to the QTL x Environment interaction. We suggest that rhizosheath size alone is not a reliable trait to predict P efficiency or grain yield.

Dark fermentation of complex waste biomass for biohydrogen production by pretreated thermophilic anaerobic digestate.

PubMed

Ghimire, Anish; Frunzo, Luigi; Pontoni, Ludovico; d'Antonio, Giuseppe; Lens, Piet N L; Esposito, Giovanni; Pirozzi, Francesco

2015-04-01

The Biohydrogen Potential (BHP) of six different types of waste biomass typical for the Campania Region (Italy) was investigated. Anaerobic sludge pre-treated with the specific methanogenic inhibitor sodium 2-bromoethanesulfonic acid (BESA) was used as seed inoculum. The BESA pre-treatment yielded the highest BHP in BHP tests carried out with pre-treated anaerobic sludge using potato and pumpkin waste as the substrates, in comparison with aeration or heat shock pre-treatment. The BHP tests carried out with different complex waste biomass showed average BHP values in a decreasing order from potato and pumpkin wastes (171.1 ± 7.3 ml H2/g VS) to buffalo manure (135.6 ± 4.1 ml H2/g VS), dried blood (slaughter house waste, 87.6 ± 4.1 ml H2/g VS), fennel waste (58.1 ± 29.8 ml H2/g VS), olive pomace (54.9 ± 5.4 ml H2/g VS) and olive mill wastewater (46.0 ± 15.6 ml H2/g VS). The digestate was analyzed for major soluble metabolites to elucidate the different biochemical pathways in the BHP tests. These showed the H2 was produced via mixed type fermentation pathways. Copyright © 2015 Elsevier Ltd. All rights reserved.

H2S and volatile fatty acids elimination by biofiltration: clean-up process for biogas potential use.

PubMed

Ramírez-Sáenz, D; Zarate-Segura, P B; Guerrero-Barajas, C; García-Peña, E I

2009-04-30

In the present work, the main objective was to evaluate a biofiltration system for removing hydrogen sulfide (H(2)S) and volatile fatty acids (VFAs) contained in a gaseous stream from an anaerobic digestor (AD). The elimination of these compounds allowed the potential use of biogas while maintaining the methane (CH(4)) content throughout the process. The biodegradation of H(2)S was determined in the lava rock biofilter under two different empty bed residence times (EBRT). Inlet loadings lower than 200 g/m(3)h at an EBRT of 81 s yielded a complete removal, attaining an elimination capacity (EC) of 142 g/m(3)h, whereas at an EBRT of 31 s, a critical EC of 200 g/m(3)h was reached and the EC obtained exhibited a maximum value of 232 g/m(3)h. For 1500 ppmv of H(2)S, 99% removal was maintained during 90 days and complete biodegradation of VFAs was observed. A recovery of 60% as sulfate was obtained due to the constant excess of O(2) concentration in the system. Acetic and propionic acids as a sole source of carbon were also evaluated in the bioreactor at different inlet loadings (0-120 g/m(3)h) obtaining a complete removal (99%) for both. Microcosms biodegradation experiments conducted with VFAs demonstrated that acetic acid provided the highest biodegradation rate.

Tagatose production by immobilized recombinant Escherichia coli cells containing Geobacillus stearothermophilus l-arabinose isomerase mutant in a packed-bed bioreactor.

PubMed

Jung, Eun-Sook; Kim, Hye-Jung; Oh, Deok-Kun

2005-01-01

Using immobilized recombinant Escherichia coli cells containing Geobacillus stearothermophilus l-arabinose isomerase mutant (Gali 152), we found that the galactose isomerization reaction was maximal at 70 degrees C and pH 7.0. Manganese ion enhanced galactose isomerization to tagatose. The immobilized cells were most stable at 60 degrees C and pH 7.0. The cell and substrate concentrations and dilution rate were optimal at 34 g/L, 300 g/L, and 0.05 h(-1), respectively. Under the optimum conditions, the immobilized cell reactor with Mn2+ produced an average of 59 g/L tagatose with a productivity of 2.9 g/L.h and a conversion yield of 19.5% for the first 20 days. The operational stability of immobilized cells with Mn2+ was demonstrated, and their half-life for tagatose production was 34 days. Tagatose production was compared for free and immobilized enzymes and free and immobilized cells using the same mass of cells. Immobilized cells produced the highest tagatose concentration, indicating that cell immobilization was more efficient for tagatose production than enzyme immobilization.

Biomass and pigments production in photosynthetic bacteria wastewater treatment: effects of light sources.

PubMed

Zhou, Qin; Zhang, Panyue; Zhang, Guangming

2015-03-01

This study is aimed at enhancing biomass and pigments production together with pollution removal in photosynthetic bacteria (PSB) wastewater treatment via different light sources. Red, yellow, blue, white LED and incandescent lamp were used. Results showed different light sources had great effects on the PSB. PSB had the highest biomass production, COD removal and biomass yield with red LED. The corresponding biomass, COD removal and biomass yield reached 2580 mg/L, 88.6% and 0.49 mg-biomass/mg-COD-removal, respectively. The hydraulic retention time of wastewater treatment could be shortened to 72 h with red LED. Mechanism analysis showed higher ATP was produced with red LED than others. Light sources could significantly affect the pigments production. The pigments productions were greatly higher with LED than incandescent lamp. Yellow LED had the highest pigments production while red LED produced the highest carotenoid/bacteriochlorophyll ratio. Considering both efficiency and energy cost, red LED was the optimal light source. Copyright © 2014 Elsevier Ltd. All rights reserved.

Aqueous Phase Non Enzymatic Chemistry of Cyanide, Formaldehyde and RNH2

NASA Technical Reports Server (NTRS)

Lerner, Narcinda R.; Chang, Sherwood (Technical Monitor)

1994-01-01

It is postulated that amino acids were produced on the early earth from dilute aqueous solution of cyanide, carbonyls and ammonia (the Strecker synthesis RNH2 + R"R""C=O + KCN yields H-N(R)-C(R")(R"")-CO2H. We have studied the products obtained from dilute aqueous solutions of cyanide, formaldehyde (R"=R""=H), ammonia (R=H) and amino acids. Solutions in the pH range from 8 to 10. at room temperature and at reactant concentrations from 0.001 M to 0.3 M have been studied. With R= H product yields were low (less than 3%). Only with R"=R""=H and R represented by the following: CH2CO2H (glycine); CH(CH3)CO2H (alanine); CH(CH2CH3)CO2H (a-amino n=butyric acids); C(CH3)2(CO2H) (a-aminoisobutyric acid); CH(CH(CH3)2)CO2H (valine); and CH(CH2CO2H)CO2H (aspartic acid), were product yields high (greater than 10%). The yields of glycine were larger with R not equal to H. The prebiotic implications of these findings will be discussed.

Effects of nutrient ratios and carbon dioxide bio-sequestration on biomass growth of Chlorella sp. in bubble column photobioreactor.

PubMed

Vo, Hoang-Nhat-Phong; Bui, Xuan-Thanh; Nguyen, Thanh-Tin; Nguyen, Dinh Duc; Dao, Thanh-Son; Cao, Ngoc-Dan-Thanh; Vo, Thi-Kim-Quyen

2018-08-01

Photobioreactor technology, especially bubble column configuration, employing microalgae cultivation (e.g., Chlorella sp.), is an ideal man-made environment to achieve sufficient microalgae biomass through its strictly operational control. Nutrients, typically N and P, are necessary elements in the cultivation process, which determine biomass yield and productivity. Specifically, N:P ratios have certain effects on microalgae's biomass growth. It is also attractive that microalgae can sequester CO 2 by using that carbon source for photosynthesis and, subsequently, reducing CO 2 emission. Therefore, this study aims to investigate the effect of N:P ratios on Chlorella sp.'s growth, and to study the dynamic of CO 2 fixation in the bubble column photobioreactor. According to our results, N:P ratio of 15:1 could produce the highest biomass yield (3568 ± 158 mg L -1 ). The maximum algae concentration was 105 × 10 6  cells mL -1 , receiving after 92 h. Chlorella sp. was also able to sequester CO 2 at 28 ± 1.2%, while the specific growth rate and carbon fixation rate were observed at 0.064 h -1 and 68.9 ± 1.91 mg L -1  h -1 , respectively. The types of carbon sources (e.g., organic and inorganic carbon) possessed potential impact on microalgae's cultivation. Copyright © 2018 Elsevier Ltd. All rights reserved.

Combined Extraction Processes of Lipid from Chlorella vulgaris Microalgae: Microwave Prior to Supercritical Carbon Dioxide Extraction

PubMed Central

Dejoye, Céline; Vian, Maryline Abert; Lumia, Guy; Bouscarle, Christian; Charton, Frederic; Chemat, Farid

2011-01-01

Extraction yields and fatty acid profiles from freeze-dried Chlorella vulgaris by microwave pretreatment followed by supercritical carbon dioxide (MW-SCCO2) extraction were compared with those obtained by supercritical carbon dioxide extraction alone (SCCO2). Work performed with pressure range of 20–28 Mpa and temperature interval of 40–70 °C, gave the highest extraction yield (w/w dry weight) at 28 MPa/40 °C. MW-SCCO2 allowed to obtain the highest extraction yield (4.73%) compared to SCCO2 extraction alone (1.81%). Qualitative and quantitative analyses of microalgae oil showed that palmitic, oleic, linoleic and α-linolenic acid were the most abundant identified fatty acids. Oils obtained by MW-SCCO2 extraction had the highest concentrations of fatty acids compared to SCCO2 extraction without pretreatment. Native form, and microwave pretreated and untreated microalgae were observed by scanning electronic microscopy (SEM). SEM micrographs of pretreated microalgae present tearing wall agglomerates. After SCCO2, microwave pretreated microalgae presented several micro cracks; while native form microalgae wall was slightly damaged. PMID:22272135

Carbon dioxide hydrogenation catalysed by well-defined Mn(i) PNP pincer hydride complexes.

PubMed

Bertini, Federica; Glatz, Mathias; Gorgas, Nikolaus; Stöger, Berthold; Peruzzini, Maurizio; Veiros, Luis F; Kirchner, Karl; Gonsalvi, Luca

2017-07-01

The catalytic reduction of carbon dioxide is of great interest for its potential as a hydrogen storage method and to use carbon dioxide as C-1 feedstock. In an effort to replace expensive noble metal-based catalysts with efficient and cheap earth-abundant counterparts, we report the first example of Mn(i)-catalysed hydrogenation of CO 2 to HCOOH. The hydride Mn(i) catalyst [Mn(PNP NH - i Pr)(H)(CO) 2 ] showed higher stability and activity than its Fe(ii) analogue. TONs up to 10 000 and quantitative yields were obtained after 24 h using DBU as the base at 80 °C and 80 bar total pressure. At catalyst loadings as low as 0.002 mol%, TONs greater than 30 000 could be achieved in the presence of LiOTf as the co-catalyst, which are among the highest activities reported for base-metal catalysed CO 2 hydrogenations to date.

Alkaline-sulfite pretreatment and use of surfactants during enzymatic hydrolysis to enhance ethanol production from sugarcane bagasse.

PubMed

Mesquita, Jéssica Faria; Ferraz, André; Aguiar, André

2016-03-01

Sugarcane bagasse is a by-product from the sugar and ethanol industry which contains approximately 70 % of its dry mass composed by polysaccharides. To convert these polysaccharides into fuel ethanol it is necessary a pretreatment step to increase the enzymatic digestibility of the recalcitrant raw material. In this work, sugarcane bagasse was pretreated by an alkaline-sulfite chemithermomechanical process for increasing its enzymatic digestibility. Na2SO3 and NaOH ratios were fixed at 2:1, and three increasing chemical loads, varying from 4 to 8 % m/m Na2SO3, were used to prepare the pretreated materials. The increase in the alkaline-sulfite load decreased the lignin content in the pretreated material up to 35.5 % at the highest chemical load. The pretreated samples presented enhanced glucose yields during enzymatic hydrolysis as a function of the pretreatment severity. The maximum glucose yield (64 %) was observed for the samples pretreated with the highest chemical load. The use of 2.5 g l(-1) Tween 20 in the hydrolysis step further increased the glucose yield to 75 %. Semi-simultaneous hydrolysis and fermentation of the pretreated materials indicated that the ethanol yield was also enhanced as a function of the pretreatment severity. The maximum ethanol yield was 56 ± 2 % for the sample pretreated with the highest chemical load. For the sample pretreated with the lowest chemical load (2 % m/m NaOH and 4 % m/m Na2SO3), adding Tween 20 during the hydrolysis process increased the ethanol yield from 25 ± 3 to 39.5 ± 1 %.

Phosphoesterification of soybean and peanut proteins with sodium trimetaphosphate (STMP): Changes in structure to improve functionality for food applications.

PubMed

Sánchez-Reséndiz, Aidee; Rodríguez-Barrientos, Sayra; Rodríguez-Rodríguez, José; Barba-Dávila, Bertha; Serna-Saldívar, Sergio O; Chuck-Hernández, Cristina

2018-09-15

Soybean and peanut protein isolates underwent phosphorylation using sodium trimetaphosphate (STMP). Changes in functional properties and the influence of STMP (1, 2 or 3% w/w), pH (11.5 or 12.5), temperature (35 or 55 °C) and time (3 or 5 h) were evaluated. The highest degree of phosphorylation was achieved at 2% of STMP and pH 12.5. The best specific conditions varied according to the raw material: in soybean, 25% phosphorylation was achieved at 55 °C and 5 h whereas in peanut, 30% was reached at 35 °C and 3 h. The modified proteins showed an improved emulsifying activity (27.3% for soybean and 6.6% for peanut), whereas NSI for soybean increased more than three times and for peanut decreased by half. In vitro digestibility improved in both isolates around 1.5%. These results showed that phosphorylation with STMP of peanut and soybean proteins yielded isolates with a wide array of potential applications in food systems. Copyright © 2018 Elsevier Ltd. All rights reserved.

Removal Efficiency of the Heavy Metals Zn(II), Pb(II) and Cd(II) by Saprolegnia delica and Trichoderma viride at Different pH Values and Temperature Degrees

PubMed Central

Hashem, Mohamed

2007-01-01

The removal efficiency of the heavy metals Zn, Pb and Cd by the zoosporic fungal species Saprolegnia delica and the terrestrial fungus Trichoderma viride, isolated from polluted water drainages in the Delta of Nile in Egypt, as affected by various ranges of pH values and different temperature degrees,was extensively investigated. The maximum removal efficiency of S. delica for Zn(II) and Cd(II) was obtained at pH 8 and for Pb(II) was at pH 6 whilst the removal efficiency of T. viride was found to be optimum at pH 6 for the three applied heavy metals. Regardless the median lethal doses of the three heavy metals, Zn recorded the highest bioaccumulation potency by S. delica at all pH values except at pH 4, followed by Pb whereas Cd showed the lowest removal potency by the fungal species and vice versa in case of T. viride. The optimum biomass dry weight production by S. delica was found when the fungus was grown in the medium treated with the heavy metal Pb at pH 6, followed by Zn at pH 8 and Cd at pH 8. The optimum biomass dry weight yield by T. viride amended with Zn,Pb and Cd was obtained at pH 6 for the three heavy metals with the maximum value at Zn. The highest yield of biomass dry weight was found when T. viride treated with Cd at all different pH values followed by Pb whilst Zn output was the lowest and this result was reversed in case of S. delica. The maximum removal efficiency and the biomass dry weight production for the three tested heavy metals was obtained at the incubation temperature 20℃ in case of S. delica while it was 25℃ for T. viride. Incubation of T. viride at higher temperatures (30℃ and 35℃) enhanced the removal efficiency of Pb and Cd than low temperatures (15℃ and 20℃) and vice versa in case of Zn removal. At all tested incubation temperatures, the maximum yield of biomass dry weight was attained at Zn treatment by the two tested fungal species. The bioaccumulation potency of S. delica for Zn was higher than that for Pb at all temperature degrees of incubation and Cd bioaccumulation was the lowest whereas T. viride showed the highest removal efficiency for Pb followed by Cd and Zn was the minor of the heavy metals. PMID:24015084

Ethanol production from lignocellulosic hydrolysates using engineered Saccharomyces cerevisiae harboring xylose isomerase-based pathway.

PubMed

Ko, Ja Kyong; Um, Youngsoon; Woo, Han Min; Kim, Kyoung Heon; Lee, Sun-Mi

2016-06-01

The efficient co-fermentation of glucose and xylose is necessary for the economically feasible bioethanol production from lignocellulosic biomass. Even with xylose utilizing Saccharomyces cerevisiae, the efficiency of the lignocellulosic ethanol production remains suboptimal mainly due to the low conversion yield of xylose to ethanol. In this study, we evaluated the co-fermentation performances of SXA-R2P-E, a recently engineered isomerase-based xylose utilizing strain, in mixed sugars and in lignocellulosic hydrolysates. In a high-sugar fermentation with 70g/L of glucose and 40g/L of xylose, SXA-R2P-E produced 50g/L of ethanol with an yield of 0.43gethanol/gsugars at 72h. From dilute acid-pretreated hydrolysates of rice straw and hardwood (oak), the strain produced 18-21g/L of ethanol with among the highest yield of 0.43-0.46gethanol/gsugars ever reported. This study shows a highly promising potential of a xylose isomerase-expressing strain as an industrially relevant ethanol producer from lignocellulosic hydrolysates. Copyright © 2016 Elsevier Ltd. All rights reserved.

Extraction optimization of mucilage from Basil (Ocimum basilicum L.) seeds using response surface methodology.

PubMed

Nazir, Sadaf; Wani, Idrees Ahmed; Masoodi, Farooq Ahmad

2017-05-01

Aqueous extraction of basil seed mucilage was optimized using response surface methodology. A Central Composite Rotatable Design (CCRD) for modeling of three independent variables: temperature (40-91 °C); extraction time (1.6-3.3 h) and water/seed ratio (18:1-77:1) was used to study the response for yield. Experimental values for extraction yield ranged from 7.86 to 20.5 g/100 g. Extraction yield was significantly ( P  < 0.05) affected by all the variables. Temperature and water/seed ratio were found to have pronounced effect while the extraction time was found to have minor possible effects. Graphical optimization determined the optimal conditions for the extraction of mucilage. The optimal condition predicted an extraction yield of 20.49 g/100 g at 56.7 °C, 1.6 h, and a water/seed ratio of 66.84:1. Optimal conditions were determined to obtain highest extraction yield. Results indicated that water/seed ratio was the most significant parameter, followed by temperature and time.

Effects of eliminating pyruvate node pathways and of coexpression of heterogeneous carboxylation enzymes on succinate production by Enterobacter aerogenes.

PubMed

Tajima, Yoshinori; Yamamoto, Yoko; Fukui, Keita; Nishio, Yousuke; Hashiguchi, Kenichi; Usuda, Yoshihiro; Sode, Koji

2015-02-01

Lowering the pH in bacterium-based succinate fermentation is considered a feasible approach to reduce total production costs. Newly isolated Enterobacter aerogenes strain AJ110637, a rapid carbon source assimilator under weakly acidic (pH 5.0) conditions, was selected as a platform for succinate production. Our previous work showed that the ΔadhE/PCK strain, developed from AJ110637 with inactivated ethanol dehydrogenase and introduced Actinobacillus succinogenes phosphoenolpyruvate carboxykinase (PCK), generated succinate as a major product of anaerobic mixed-acid fermentation from glucose under weakly acidic conditions (pH <6.2). To further improve the production of succinate by the ΔadhE/PCK strain, metabolically engineered strains were designed based on the elimination of pathways that produced undesirable products and the introduction of two carboxylation pathways from phosphoenolpyruvate and pyruvate to oxaloacetate. The highest production of succinate was observed with strain ES04/PCK+PYC, which had inactivated ethanol, lactate, acetate, and 2,3-butanediol pathways and coexpressed PCK and Corynebacterium glutamicum pyruvate carboxylase (PYC). This strain produced succinate from glucose with over 70% yield (gram per gram) without any measurable formation of ethanol, lactate, or 2,3-butanediol under weakly acidic conditions. The impact of lowering the pH from 7.0 to 5.5 on succinate production in this strain was evaluated under pH-controlled batch culture conditions and showed that the lower pH decreased the succinate titer but increased its yield. These findings can be applied to identify additional engineering targets to increase succinate production. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

Screening of Six Medicinal Plant Extracts Obtained by Two Conventional Methods and Supercritical CO₂ Extraction Targeted on Coumarin Content, 2,2-Diphenyl-1-picrylhydrazyl Radical Scavenging Capacity and Total Phenols Content.

PubMed

Molnar, Maja; Jerković, Igor; Suknović, Dragica; Bilić Rajs, Blanka; Aladić, Krunoslav; Šubarić, Drago; Jokić, Stela

2017-02-24

Six medicinal plants Helichrysum italicum (Roth) G. Don, Angelica archangelica L., Lavandula officinalis L., Salvia officinalis L., Melilotus officinalis L., and Ruta graveolens L. were used. The aim of the study was to compare their extracts obtained by Soxhlet (hexane) extraction, maceration with ethanol (EtOH), and supercritical CO₂ extraction (SC-CO₂) targeted on coumarin content (by high performance liquid chromatography with ultraviolet detection, HPLC-UV), 2,2-diphenyl-1-picrylhydrazyl radical (DPPH) scavenging capacity, and total phenols (TPs) content (by Folin-Ciocalteu assay). The highest extraction yields were obtained by EtOH, followed by hexane and SC-CO₂. The highest coumarin content (316.37 mg/100 g) was found in M. officinalis EtOH extracts, but its SC-CO₂ extraction yield was very low for further investigation. Coumarin was also found in SC-CO₂ extracts of S. officinalis , R. graveolens , A. archangelica , and L. officinalis . EtOH extracts of all plants exhibited the highest DPPH scavenging capacity. SC-CO₂ extracts exhibited antiradical capacity similar to hexane extracts, while S. officinalis SC-CO₂ extracts were the most potent (95.7%). EtOH extracts contained the most TPs (up to 132.1 mg gallic acid equivalents (GAE)/g from H. italicum ) in comparison to hexane or SC-CO₂ extracts. TPs content was highly correlated to the DPPH scavenging capacity of the extracts. The results indicate that for comprehensive screening of different medicinal plants, various extraction techniques should be used in order to get a better insight into their components content or antiradical capacity.

The Broken Ring: Reduced Aromaticity in Lys-Trp Cations and High pH Tautomer Correlates with Lower Quantum Yield and Shorter Lifetimes

PubMed Central

2015-01-01

Several nonradiative processes compete with tryptophan fluorescence emission. The difficulty in spectral interpretation lies in associating specific molecular environmental features with these processes and thereby utilizing the fluorescence spectral data to identify the local environment of tryptophan. Here, spectroscopic and molecular modeling study of Lys-Trp dipeptide charged species shows that backbone-ring interactions are undistinguished. Instead, quantum mechanical ground state isosurfaces reveal variations in indole π electron distribution and density that parallel charge (as a function of pK1, pK2, and pKR) on the backbone and residues. A pattern of aromaticity-associated quantum yield and fluorescence lifetime changes emerges. Where quantum yield is high, isosurfaces have a charge distribution similar to the highest occupied molecular orbital (HOMO) of indole, which is the dominant fluorescent ground state of the 1La transition dipole moment. Where quantum yield is low, isosurface charge distribution over the ring is uneven, diminished, and even found off ring. At pH 13, the indole amine is deprotonated, and Lys-Trp quantum yield is extremely low due to tautomer structure that concentrates charge on the indole amine; the isosurface charge distribution bears scant resemblance to the indole HOMO. Such greatly diminished fluorescence has been observed for proteins where the indole nitrogen is hydrogen bonded, lending credence to the association of aromaticity changes with diminished quantum yield in proteins as well. Thus tryptophan ground state isosurfaces are an indicator of indole aromaticity, signaling the partition of excitation energy between radiative and nonradiative processes. PMID:24882092

Arsenic release from Fe/Mn oxide-rich (model) soils/sediments - A comparison of single extraction procedures

NASA Astrophysics Data System (ADS)

Vanek, A.; Komarek, M.; Galuskova, I.

2012-04-01

Arsenic extractability in As-modified Fe(III) and Mn(III,IV) oxide-coated sands was tested using five widely used 2-h single extraction procedures: deionised water, 0.01 M CaCl2, 1 M NH4NO3, 0.1 M Na2HPO4 and 0.005 DTPA. In general, the highest As recoveries reaching 39-50% of total As concentration were observed for all extracting media in the birnessite (delta-MnO2) system, indicating relatively weak adsorption of As onto the Mn oxides. The Na2HPO4 extracts from the Fe oxide systems (i.e., associated with ferrihydrite and goethite) were highest in As, accounting for up to 34% of total As amount. Surprisingly, comparable recoveries of As (14-20%) yielded deionised water, CaCl2, NH4NO3, DTPA as extracting media for both ferrihydrite and goethite coatings. Deionised water and Na2HPO4 extractions are suggested for quick estimation of easily soluble, exchangeable and/or specifically adsorbed As in real soil/sediment samples.

Activating and optimizing MoS 2 basal planes for hydrogen evolution through the formation of strained sulphur vacancies

DOE PAGES

Li, Hong; Tsai, Charlie; Koh, Ai Leen; ...

2015-11-09

As a promising non-precious catalyst for the hydrogen evolution reaction, molybdenum disulphide (MoS 2) is known to contain active edge sites and an inert basal plane. Activating the MoS 2 basal plane could further enhance its HER activity but is not often a strategy for doing so. Herein, we report the first activation and optimization of the basal plane of monolayer 2H-MoS 2 for HER by introducing sulphur (S) vacancies and strain. Our theoretical and experimental results show that the S-vacancies are new catalytic sites in the basal plane, where gap states around the Fermi level allow hydrogen to bindmore » directly to exposed Mo atoms. The hydrogen adsorption free energy (ΔG H) can be further manipulated by straining the surface with S-vacancies, which fine-tunes the catalytic activity. Furthermore, proper combinations of S-vacancy and strain yield the optimal ΔG H = 0 eV, which allows us to achieve the highest intrinsic HER activity among molybdenum-sulphide-based catalysts.« less

Identification of conjugate adducts formed in the reactions of malonaldehyde-acetaldehyde and malonaldehyde-formaldehyde with cytidine.

PubMed

Pluskota-Karwatka, Donata; Le Curieux, Frank; Munter, Tony; Sjöholm, Rainer; Kronberg, Leif

2002-02-01

Malonaldehyde was reacted with cytidine in buffered aqueous solutions in the presence of acetaldehyde or formaldehyde. The reaction mixtures were analyzed by HPLC, and the products were isolated by preparative C18 chromatography and structurally characterized by UV absorbance, fluorescence emission, (1)H and (13)C NMR spectroscopy, and mass spectrometry. The major adducts formed in the reaction of malonaldehyde and acetaldehyde were identified as 7-(beta-D-ribofuranosyl)-4-methyl-6-oxo-6,7-dihydro-4H-pyrimido[1,6-a]pyrimidine-3-carbaldehyde (M(1)AA-Cyd) and 1-(beta-D-ribofuranosyl)-4-(3,5-diformyl-4-methyl-1,4-dihydro-1-pyridyl)pyrimidine (M(2)AA-Cyd). In the reaction of malonaldehyde and formaldehyde, the major product was identified as 7-(beta-D-ribofuranosyl)-6-oxo-6,7-dihydro-4H-pyrimido[1,6-a]pyrimidine-3-carbaldehyde (M(1)FA-Cyd). The highest yields of M(1)AA-Cyd and M(2)AA-Cyd, 3.2 and 0.5 mol %, respectively, were obtained in the reaction performed at pH 4.6 and 37 degrees C for 8 days, while M(1)FA-Cyd was produced at a yield of 0.3 mol % after 3 days of reaction at pH 4.0 and 37 degrees C. The products consist of units derived from malonaldehyde and acetaldehyde (M(1)AA-Cyd and M(2)AA-Cyd) or from malonaldehyde and formaldehyde (M(1)FA-Cyd), and are thus further examples of nucleoside modifications containing structural elements derived from aldehyde condensation reactions. Trace amounts of the adducts may be formed at physiological conditions and may be involved in the mutagenicity of the studied aldehydes.

Performance, carotenoids yield and microbial population dynamics in a photobioreactor system treating acidic wastewater: Effect of hydraulic retention time (HRT) and organic loading rate (OLR).

PubMed

Liu, Shuli; Zhang, Guangming; Zhang, Jie; Li, Xiangkun; Li, Jianzheng

2016-01-01

Effects of hydraulic retention time (HRT) and influent organic loading rate (OLR) were investigated in a photobioreactor containing PNSB (Rhodopseudomonas palustris)-chemoheterotrophic bacteria to treat volatile fatty acid wastewater. Pollutants removal, biomass production and carotenoids yield in different phases were investigated in together with functional microbial population dynamics. The results indicated that properly decreasing HRT and increasing OLR improved the nutrient removal performance as well as the biomass and carotenoids productions. 85.7% COD, 89.9% TN and 91.8% TP removals were achieved under the optimal HRT of 48h and OLR of 2.51g/L/d. Meanwhile, the highest biomass production and carotenoids yield were 2719.3mg/L and 3.91mg/g-biomass respectively. In addition, HRT and OLR have obvious impacts on PNSB and total bacteria dynamics. Statistical analyses indicated that the COD removal exhibited a positive relationship with OLR, biomass and carotenoids production. PNSB/total bacteria ratio had a positive correlation with the carotenoids yield. Copyright © 2015 Elsevier Ltd. All rights reserved.

Production of bacterial cellulose using different carbon sources and culture media.

PubMed

Mohammadkazemi, Faranak; Azin, Mehrdad; Ashori, Alireza

2015-03-06

In this work, the effects of carbon sources and culture media on the production and structural properties of bacterial cellulose (BC) have been studied. BC nanofibers were synthesized using Gluconacetobacter xylinus strain PTCC 1734. Media used were Hestrin-Schramm (H), Yamanaka (Y), and Zhou (Z). Five different carbon sources, namely date syrup, glucose, mannitol, sucrose, and food-grade sucrose were used in these media. All the produced BC pellicles were characterized in terms of dry weight production, biomass yield, thermal stability, crystallinity and morphology by thermogravimetric analysis (TGA), x-ray diffraction (XRD), and field emission scanning electron microscopy (FE-SEM). The obtained results showed that mannitol lead to the highest yield, followed by sucrose. The highest production efficiency of mannitol might be due to the nitrogen source, which plays an important role. The maximum improvement on the thermal stability of the composites was achieved when mannitol was used in H medium. In addition, the crystallinity was higher in BC formed in H medium compared to other media. FE-SEM micrographs illustrated that the BC pellicles, synthesized in the culture media H and Z, were stable, unlike those in medium Y that were unstable. The micrographs of BC produced in media containing mannitol and sucrose provided evidence of the strong interfacial adhesion between the BC fibers without noticeable aggregates. Copyright © 2014 Elsevier Ltd. All rights reserved.

The products of the thermal decomposition of CH{sub 3}CHO

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vasiliou, AnGayle; National Renewable Energy Laboratory, 1617 Cole Blvd., Golden, Colorado 80401; Piech, Krzysztof M.

2011-07-07

We have used a heated 2 cm x 1 mm SiC microtubular ({mu}tubular) reactor to decompose acetaldehyde: CH{sub 3}CHO +{Delta}{yields} products. Thermal decomposition is followed at pressures of 75-150 Torr and at temperatures up to 1675 K, conditions that correspond to residence times of roughly 50-100 {mu}s in the {mu}tubular reactor. The acetaldehyde decomposition products are identified by two independent techniques: vacuum ultraviolet photoionization mass spectroscopy (PIMS) and infrared (IR) absorption spectroscopy after isolation in a cryogenic matrix. Besides CH{sub 3}CHO, we have studied three isotopologues, CH{sub 3}CDO, CD{sub 3}CHO, and CD{sub 3}CDO. We have identified the thermal decomposition productsmore » CH{sub 3} (PIMS), CO (IR, PIMS), H (PIMS), H{sub 2} (PIMS), CH{sub 2}CO (IR, PIMS), CH{sub 2}=CHOH (IR, PIMS), H{sub 2}O (IR, PIMS), and HC{identical_to}CH (IR, PIMS). Plausible evidence has been found to support the idea that there are at least three different thermal decomposition pathways for CH{sub 3}CHO; namely, radical decomposition: CH{sub 3}CHO +{Delta}{yields} CH{sub 3}+[HCO]{yields} CH{sub 3}+ H + CO; elimination: CH{sub 3}CHO +{Delta}{yields} H{sub 2}+ CH{sub 2}=C=O; isomerization/elimination: CH{sub 3}CHO +{Delta}{yields}[CH{sub 2}=CH-OH]{yields} HC{identical_to}CH + H{sub 2}O. An interesting result is that both PIMS and IR spectroscopy show compelling evidence for the participation of vinylidene, CH{sub 2}=C:, as an intermediate in the decomposition of vinyl alcohol: CH{sub 2}=CH-OH +{Delta}{yields}[CH{sub 2}=C:]+ H{sub 2}O {yields} HC{identical_to}CH + H{sub 2}O.« less

Influence of Water on the H2SO4 Yield from the Ozonolysis of 2,3-dimethyl-butene (TME) in Presence of SO2

NASA Astrophysics Data System (ADS)

Véronique, D.; Kukui, A.; Chen, H.; Mellouki, A.

2016-12-01

The influence of the water vapor content on the yield of H2SO4 from the ozonolysis of 2,3-dimethyl-butene (TME) in presence of SO2 was studied using laminar flow reactor coupled with Chemical Ionisation Mass Spectrometer (CIMS) for the H2SO4 monitoring within the range of H2O from 10 ppmv to 3×104 ppmv at different concentrations of TME, O3, SO2. The observed dependences of the H2SO4 yield on H2O concentration can be interpreted by assuming two different paths of the H2SO4 formation: 1) via the formation of SO3 in the reaction of Stabilized Criegee Intermediate (SCI) with SO2 (2a) followed by the reaction of SO3 with H2O (3) and 2) via the formation of stabilized secondary ozonide (SOZ) (2b) producing H2SO4 in the reaction with H2O (4a) in competition with the SOZ decomposition to other products (5): O3+TME => (CH3)2COO (1) (CH3)2COO + SO2 => SO3 (2a) => SOZ (2b) SO3 + H2O => H2SO4 (3) SOZ + H2O => H2SO4 (or SO3) (4a) SOZ + M => products (5) The yield of the SCI, SOZ and the rates of the SCI and SOZ decomposition relative to their reactions with SO2 and H2O, respectively, were estimated from the dependencies of the H2SO4 yield on the concentrations of the reactants.

Comparison of different liquid anaerobic digestion effluents as inocula and nitrogen sources for solid-state batch anaerobic digestion of corn stover

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu Fuqing; Shi Jian; Lv Wen

2013-01-15

Highlights: Black-Right-Pointing-Pointer Compared methane production of solid AD inoculated with different effluents. Black-Right-Pointing-Pointer Food waste effluent (FWE) had the largest population of acetoclastic methanogens. Black-Right-Pointing-Pointer Solid AD inoculated with FWE produced the highest methane yield at F/E ratio of 4. Black-Right-Pointing-Pointer Dairy waste effluent (DWE) was rich of cellulolytic and xylanolytic bacteria. Black-Right-Pointing-Pointer Solid AD inoculated with DWE produced the highest methane yield at F/E ratio of 2. - Abstract: Effluents from three liquid anaerobic digesters, fed with municipal sewage sludge, food waste, or dairy waste, were evaluated as inocula and nitrogen sources for solid-state batch anaerobic digestion of cornmore » stover in mesophilic reactors. Three feedstock-to-effluent (F/E) ratios (i.e., 2, 4, and 6) were tested for each effluent. At an F/E ratio of 2, the reactor inoculated by dairy waste effluent achieved the highest methane yield of 238.5 L/kgVS{sub feed}, while at an F/E ratio of 4, the reactor inoculated by food waste effluent achieved the highest methane yield of 199.6 L/kgVS{sub feed}. The microbial population and chemical composition of the three effluents were substantially different. Food waste effluent had the largest population of acetoclastic methanogens, while dairy waste effluent had the largest populations of cellulolytic and xylanolytic bacteria. Dairy waste also had the highest C/N ratio of 8.5 and the highest alkalinity of 19.3 g CaCO{sub 3}/kg. The performance of solid-state batch anaerobic digestion reactors was closely related to the microbial status in the liquid anaerobic digestion effluents.« less

Bioconversion of glycerol to 1,3-propanediol in thin stillage-based media by engineered Lactobacillus panis PM1.

PubMed

Kang, Tae Sun; Korber, Darren R; Tanaka, Takuji

2014-04-01

Thin stillage (TS) is a waste residue that remains after bioethanol production, and its disposal reflects the high costs of bioethanol production. Thus, the development of cost-effective ways to process TS is a pending issue in bioethanol plants. The aim of this study was to evaluate the utilization of TS for the production of the valuable chemical, 1,3-propanediol (1,3-PDO), by Lactobacillus panis PM1. Different fermentation parameters, including temperature, pH and strains [wild-type and a recombinant strain expressing a NADPH-dependent aldehyde reductase (YqhD) gene] were tested in batch and fed-batch cultivations. The highest 1,3-PDO concentration (12.85 g/L) and yield (0.84 g/g) were achieved by batch fermentation at pH-4.5/30 °C by the YqhD recombinant strain. Furthermore, pH-controlled batch fermentation reduced the total fermentation period, resulting in the maximal 1,3-PDO concentration of 16.23 g/L and yield of 0.72 g/g in TS without an expensive nutrient or nitrogen (e.g., yeast extract, beef extract, and peptone) supplementation. The addition of two trace elements, Mg(2+) and Mn(2+), in TS increased 1,3-PDO yield (0.74 g/g) without 3-hydroxypropionaldehyde production, the only intermediate of 1,3-PDO biosynthetic pathway in L. panis PM1. Our results suggest that L. panis PM1 can offer a cost-effective process that utilizes the TS to produce a value-added chemical, 1,3-PDO.

Impacts of industrial waste resources on maize (Zea mays L.) growth, yield, nutrients uptake and soil properties.

PubMed

Singh, Satnam; Young, Li-Sen; Shen, Fo-Ting; Young, Chiu-Chung

2014-10-01

Discharging untreated highly acidic (pH<4.0), organic and nutrients rich monosodium glutamate wastewater (MW), and highly alkaline (pH>10.0) paper-mill wastewater (PW) causes environmental pollution. When acidity of MW neutralized (pH 6.5±0.1) with PW and lime (treatments represented as MW+PW and MW+Lime), then MW may be utilized as a potential source of nutrients and organic carbon for sustainable food production. Objectives of this study were to compare the effects of PW and lime neutralized MW and chemical fertilizers on maize (Zea mays L. cv. Snow Jean) plant growth, yield, nutrients uptake, soil organic matter and humic substances. The field experiment was carried out on maize using MW at 6000 L ha(-1). Impacts of the MW application on maize crop and soil properties were evaluated at different stages. At harvest, plant height, and plant N and K uptake were higher in MW treatment. Leaf area index at 60 days after sowing, plant dry matter accumulation at harvest, and kernels ear(-1) and 100-kernel weight were higher in MW+Lime treatment. Kernel N, P, K, Mn, Fe and Zn, and plant Zn uptake were highest in MW+Lime. Plant Fe uptake, and soil organic matter and humic substances were highest in MW+PW. The MW+PW and MW+Lime treatments exhibited comparable results with chemically fertilized treatment. The MW acidity neutralized with lime showed positive impacts on growth, yield and nutrients uptake; nevertheless, when MW pH neutralized with PW has an additional benefit on increase in soil organic matter and humic substances. Copyright © 2014. Published by Elsevier Ltd.

Pressurized entrained-flow pyrolysis of microalgae: Enhanced production of hydrogen and nitrogen-containing compounds.

PubMed

Maliutina, Kristina; Tahmasebi, Arash; Yu, Jianglong

2018-05-01

Pressurized entrained-flow pyrolysis of Chlorella vulgaris microalgae was investigated. The impact of pressure on the yield and composition of pyrolysis products were studied. The results showed that the concentration of H 2 in bio-gas increased sharply with increasing pyrolysis pressure, while those of CO, CO 2 , CH 4 , and C 2 H 6 were dramatically decreased. The concentration of H 2 reached 88.01 vol% in bio-gas at 900 °C and 4 MPa. Higher pressures promoted the hydrogen transfer to bio-gas. The bio-oils derived from pressurized pyrolysis were rich in nitrogen-containing compounds and PAHs. The highest concentration of nitrogen-containing compounds in bio-oil was achieved at 800 °C and 1 MPa. Increasing pyrolysis pressure promoted the formation of nitrogen-containing compounds such as indole, quinoline, isoquinoline and phenanthridine. Higher pyrolysis pressures led to increased sphericity, enhanced swelling, and higher carbon order of bio-chars. Pressurized pyrolysis of biomass has a great potential for poly-generation of H 2 , nitrogen containing compounds and bio-char. Copyright © 2018 Elsevier Ltd. All rights reserved.

Reaction engineering analysis of Scenedesmus ovalternus in a flat-plate gas-lift photobioreactor.

PubMed

Koller, Anja Pia; Wolf, Lara; Weuster-Botz, Dirk

2017-02-01

Microalgal strains of the genus Scenedesmus are a promising resource for commercial biotechnological applications. The temperature-, pH- and light-dependent growth of Scenedesmus ovalternus has been investigated on a laboratory scale. Best batch process performance was obtained at 30°C, pH 8.0 and an incident photon flux density of 1300μmolphotonsm -2 s -1 using a flat-plate gas-lift photobioreactor. Highest growth rate (0.11h -1 ) and space-time yield (1.7±0.1g CDW L -1 d -1 ) were observed when applying these reaction conditions. Biomass concentrations of up to 7.5±0.1g CDW L -1 were achieved within six days (25.0±0.5g CDW m -2 d -1 ). The light-dependent growth kinetics of S. ovalternus was identified using Schuster's light transfer model and Andrews' light inhibition model (K S =545μmolphotonsm -2 s -1 ; K I =2744μmolphotonsm -2 s -1 ; μ max =0.21h -1 ). The optimal mean integral photon flux density for growth of S. ovalternus was estimated to be 1223μmolphotonsm -2 s -1 . Copyright © 2016 Elsevier Ltd. All rights reserved.

Factors affecting emulsion stability and quality of oil recovered from enzyme-assisted aqueous extraction of soybeans.

PubMed

Jung, S; Maurer, D; Johnson, L A

2009-11-01

The objectives of the present study were to assess how the stability of the emulsion recovered from aqueous extraction processing of soybeans was affected by characteristics of the starting material and extraction and demulsification conditions. Adding endopeptidase Protex 6L during enzyme-assisted aqueous extraction processing (EAEP) of extruded soybean flakes was vital to obtaining emulsions that were easily demulsified with enzymes. Adding salt (up to 1.5 mM NaCl or MgCl(2)) during extraction and storing extruded flakes before extraction at 4 and 30 degrees C for up to 3 months did not affect the stabilities of emulsions recovered from EAEP of soy flour, flakes and extruded flakes. After demulsification, highest free oil yield was obtained with EAEP of extruded flakes, followed by flour and then flakes. The same protease used for the extraction step was used to demulsify the EAEP cream emulsion from extruded full-fat soy flakes at concentrations ranging from 0.03% to 2.50% w/w, incubation times ranging from 2 to 90 min, and temperatures of 25, 50 or 65 degrees C. Highest free oil recoveries were achieved at high enzyme concentrations, mild temperatures, and short incubation times. Both the nature of enzyme (i.e., protease and phospholipase), added alone or as a cocktail, concentration of enzymes (0.5% vs. 2.5%) and incubation time (1 vs. 3 h), use during the extraction step, and nature of enzyme added for demulsifying affected free oil yield. The free oil recovered from EAEP of extruded flakes contained less phosphorus compared with conventional hexane-extracted oil. The present study identified conditions rendering the emulsion less stable, which is critical to increasing free oil yield recovered during EAEP of soybeans, an environmentally friendly alternative processing method to hexane extraction.

Succinic acid production by Actinobacillus succinogenes from batch fermentation of mixed sugars.

PubMed

Almqvist, Henrik; Pateraki, Chrysanthi; Alexandri, Maria; Koutinas, Apostolis; Lidén, Gunnar

2016-08-01

Succinic acid production from the monosaccharides xylose, arabinose, glucose, mannose and galactose was studied using the bacterium Actinobacillus succinogenes. In Duran bottle cultures, containing 10 g/L of each of sugar, succinic acid was produced from all sugars except for galactose. The highest succinate yield, 0.56 g/g, was obtained with glucose, whereas the succinate yield was 0.42, 0.38 and 0.44 g/g for xylose, mannose and arabinose, respectively. The specific succinate productivity was 0.7 g/g h for glucose, but below 0.2 g/g h for the other sugars. Batch bioreactor fermentations were carried out using a sugar mixture of the five sugars giving a total concentration of 50 g/L, mimicking the distribution of sugars in spent sulfite liquor (SSL) from Eucalyptus which is rich in xylose. In this mixture, an almost complete conversion of all sugars (except galactose) was achieved resulting in a final succinate concentration of 21.8-26.8 g/L and a total yield of 0.59-0.68 g/g. There was evidence of co-consumption of glucose and xylose, whereas mannose was consumed after glucose. The main by-products were acetate 0.14-0.20 g/g and formate 0.08-0.13 g/g. NADH balance calculations suggested that NADH required for succinate production was not met solely from formate and acetate production, but other means of NADH production was necessary. Results from mixed sugar fermentations were verified using SSL as substrate resulting in a succinate yield of 0.60 g/g. In addition, it was found that CO2 sparging could replace carbonate supply in the form of MgCO3 without affecting the succinate yield.

Synthesis of fatty acid methyl ester from used vegetable cooking oil by solid reusable Mg 1-x Zn 1+x O2 catalyst.

PubMed

Olutoye, M A; Hameed, B H

2011-02-01

Fatty acid methyl ester was produced from used vegetable cooking oil using Mg(1-)(x) Zn(1+)(x)O(2) solid catalyst and the performance monitored in terms of ester content obtained. Used vegetable cooking oil was employed to reduce operation cost of biodiesel. The significant operating parameters which affect the overall yield of the process were studied. The highest ester content, 80%, was achieved with the catalyst during 4h 15 min reaction at 188°C with methanol to oil ratio of 9:1 and catalyst loading of 2.55 wt% oil. Also, transesterification of virgin oil gave higher yield with the heterogeneous catalyst and showed high selectivity towards ester production. The used vegetable cooking oil did not require any rigorous pretreatment. Catalyst stability was examined and there was no leaching of the active components, and its performance was as good at the fourth as at the first cycle. Copyright © 2010 Elsevier Ltd. All rights reserved.

The role and fate of inorganic nitrogen species during UVA/TiO₂ disinfection.

PubMed

Zuo, XiaoJun; Hu, Jiangyong; Chen, MinDong

2015-09-01

Inorganic nitrogen species have three states including ammonia nitrogen (NH4(+)/NH3), nitrite (NO2(-)) and nitrate (NO3(-)) and are often found in the disinfection system. However, no available literature could be found on their role and fate in photocatalytic disinfection systems. In this study, batch experiments were conducted to investigate bacteria inactivation, H2O2 generated and inorganic nitrogen variation to understand the role and fate of inorganic nitrogen species during UVA/TiO2 disinfection and evaluate effects of initial pH and bacteria levels on the role and fate. NH4(+)/NH3 and NO2(-) inhibited the photocatalytic disinfection process obviously. It could be confirmed through that H2O2 yield used for pathogen inactivation was dependent on NH4(+)/NH3 and NO2(-) levels. The NH4(+)/NH3 remaining, NH4(+) remaining and NO3(-) yields in only NH4(+)/NH3 photocatalytic oxidation experiments were obviously different from the corresponding values in the photocatalytic disinfection experiments with NH4(+)/NH3, which confirmed that photocatalytic disinfection had an obvious effect on the fate of NH4(+)/NH3. However, photocatalytic disinfection had slight effects on the fate of NO2(-) and NO3(-). Escherischia coli inactivation rate was the highest in neutral solutions (Initial pH 7) while the lowest in alkaline solutions (Initial pH 8.5). The decrease of NH4(+)/NH3 in alkaline solutions was the most significant. In turn, the photocatalysis of NO2(-) was more evident in acidic solutions. E. coli inactivation was reduced with the increase of initial E. coli concentrations. The initial bacteria concentrations significantly influenced the increase of NH4(+)/NH3, NH4(+) and NO3(-), but slightly impacted the decrease of NO2(-). Copyright © 2015 Elsevier Ltd. All rights reserved.

Emission Analysis Of Pr{sup 3+}: PVP And Nd{sup 3+}: PVP Films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sivaiah, K.; Buddhudu, S.

Here we report on the results concerning the absorption and emission spectra of RE{sup 3+} (Pr{sup 3+} or Nd{sup 3+}) doped PVP polymer films. The absorption spectrum of Pr{sup 3+}: PVP polymer film has shown three absorption bands at 444 nm ({sup 3}H{sub 4{yields}}{sup 3}P{sub 2}), 469nm ({sup 3}H{sub 4{yields}}{sup 3}P{sub 1}) and 481nm ({sup 3}H{sub 4{yields}}{sup 3}P{sub 0}). From the Pr{sup 3+}: PVP polymer film, an emission at 603 nm ({sup 1}D{sub 2{yields}}{sup 3}H{sub 4}) has been observed with an excitation at 443 nm ({sup 3}H{sub 4{yields}}{sup 3}P{sub 2}). The absorption spectrum of Nd{sup 3+}: PVP polymer film hasmore » exhibited eleven absorption bands at 324 nm, 383 nm, 432 nm, 462 nm, 511 nm, 526 nm, 580 nm, 686 nm, 746 nm, 799 nm, and 869 nm which are assigned to the electronic transitions of {sup 4}I{sub 9/2{yields}}{sup 4}D{sub 7/2}, {sup 4}I{sub 9/2{yields}}{sup 2}D{sub 3/2}, {sup 4}I{sub 9/2{yields}}{sup 4}P{sub 1/2}, {sup 4}I{sub 9/2{yields}}{sup 4}G{sub 11/2}, {sup 4}I{sub 9/2{yields}}{sup 4}G{sub 9/2}, {sup 4}I{sub 9/2{yields}}{sup 4}G{sub 7/2}, {sup 4}I{sub 9/2{yields}}{sup 4}G{sub 5/2}, {sup 4}I{sub 9/2{yields}}{sup 2}F{sub 9/2}, {sup 4}I{sub 9/2{yields}}{sup 2}F{sub 7/2}, {sup 4}I{sub 9/2{yields}}{sup 2}H{sub 9/2} and {sup 4}I{sub 9/2{yields}}{sup 4}F{sub 3/2} respectively. From the Nd{sup 3+}: PVP polymer film, an emission transition has been measured at 1055 nm ({sup 4}F{sub 3/2{yields}}{sup 4}I{sub 11/2}) with an excitation at 324 nm ({sup 4}I{sub 9/2{yields}}{sup 4}D{sub 7/2}). For the host polymer film, structural properties have been studied from the measurement of XRD, FTIR, Raman spectra. For this film thermal properties have also been investigated from the measured profiles of TGA-DTA.« less

Effect of temperature on short chain fatty acids (SCFAs) accumulation and microbiological transformation in sludge alkaline fermentation with Ca(OH)₂ adjustment.

PubMed

Li, XiaoLing; Peng, YongZhen; Ren, NanQi; Li, BaiKun; Chai, TongZhi; Zhang, Liang

2014-09-15

The effects of temperatures (15-55 °C) on the alkaline fermentation of sewage sludge were investigated in semi-continuous stirred tank reactors (semi - CSTR) at the pH of 10. The highest soluble chemical oxygen demand (SCOD) yield was obtained at 55 °C (764.2 mg/(gVS L d)), while the highest short chain fatty acids (SCFAs) yield was observed at 35 °C (319.8 mg/(gVS L d)), 1.5 times higher than SCFAs yield at 55 °C (209.5 mg/(gVS L d)). The proportion of the intercellular organic substances being transferred to the slime layer of sludge flocs increased from 29% at 15 °C to 54% at 55 °C. But only a small part of soluble organic substances in the slime layers was converted to SCFAs at 55 °C. The dewaterability of sludge was better at 35 °C than that at 55 °C. Microbiological community analysis showed the acid-producing microorganisms at the medium temperatures (25 °C and 35 °C) were more diverse and abundant than those at the low (15 °C) and high temperatures (55 °C). Clodtridium and Bacillus in Firmicutes and Gamma proteobacterium in Proteobacteria were the dominant functional bacterial species for high SCFA accumulation. Copyright © 2014. Published by Elsevier Ltd.

Short communication: Nutrient consumption patterns of Lactobacillus acidophilus KLDS 1.0738 in controlled pH batch fermentations.

PubMed

Lv, Xuepeng; Liu, Gefei; Sun, Xiaomei; Chen, Hongyu; Sun, Jiahui; Feng, Zhen

2017-07-01

This work focused on elucidating the nutrient consumption patterns of Lactobacillus acidophilus to guide the design of media for high-cell-density culture. We investigated the nutrient consumption patterns of L. acidophilus KLDS 1.0738 in chemically defined media in controlled pH batch fermentations. The most abundantly consumed amino acids, vitamins, ions, and purines and pyrimidines were Glu and Gly, pyridoxine and nicotinamide, K + and PO 4 3- , and guanine and uracil, respectively. The highest consumption rates for amino acids, vitamins, ions, and purines and pyrimidines were Asp and Arg, folic acid and pyridoxine, Fe 2+ and Mn 2+ , and uracil and thymine, respectively. Furthermore, most of the amino acids, as well as guanine, thymine, pyridoxine, folic acid, nicotinamide, Mg 2+ , PO 4 3- , and K + had the highest bioavailability from the end of the lag growth phase to the mid-exponential growth phase. The overall consumption of glucose, adenine nucleotides, 2'-deoxyguanosine monohydrate, calcium pantothenate, Fe 2+ and Mn 2+ decreased with increasing average growth rate, indicating more effective use of these nutritional components at a higher average growth rate, as biomass yield based on nutritional component consumption increased. Our findings help to formulate complex media for high-cell-density cultivation and provide a theoretical basis for L. acidophilus feeding strategies. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Camellia oleifera shell as an alternative feedstock for furfural production using a high surface acidity solid acid catalyst.

PubMed

Zhang, Luxin; He, Yunfei; Zhu, Yujie; Liu, Yuting; Wang, Xiaochang

2018-02-01

This paper focuses on the high-value transformation of camellia oleifera shell, which is an agricultural waste enriched in hemicellulose. An efficient catalytic route employing sulfonated swelling mesoporous polydivinylbenzene (PDVB-SO 3 H) as catalyst in monophasic or biphasic solvents was developed for the conversion of raw camellia oleifera shell into furfural. The reaction parameters were evaluated and optimized for improving the furfural yield. It was found that the solvent greatly influenced the hydrolysis of camellia oleifera shells, and the highest furfural yield of 61.3% was obtained in "γ-butyrolactone + water" system when the feedstock-to-catalyst ratio was 2 for 30 min at 443 K. Camellia oleifera shell exhibited a high potential as feedstock to produce furfural in high yields. The outcome of this study provides an attractive utilization option to camellia oleifera shell, which is currently burned or discarded for producing a bio-based chemical. Copyright © 2017 Elsevier Ltd. All rights reserved.

The effect of electrical lighting power and irradiance on indoor-grown cannabis potency and yield.

PubMed

Potter, David J; Duncombe, Paul

2012-05-01

The floral development and potencies [Δ(9) -tetrahydrocannabinol (THC) contents] of cannabis plants were compared when grown indoors under high-pressure sodium lamps consuming electrical power at three densities (270, 400, and 600 W/m(2)). After a 3-week vegetative phase, plants were grown for 8 weeks, with lamps maintaining an artificial day length of 12 h. Foliar and floral yields were measured. Gas chromatography was used to measure the content of the psychoactive cannabinoid THC. Mean yields per unit of electrical power in each lighting regime ranged from 0.9 to 1.6 g/W, the highest being achieved in the lowest irradiance regime. The individual potencies of the separated leaf and flower materials were not affected by increasing irradiance. However, there was a corresponding increase in the overall potency of the aerial plant tissue. This was because of the plants in brighter conditions producing a higher proportion of floral material. © 2011 American Academy of Forensic Sciences.

Palm-based medium-and-long-chain triacylglycerol (P-MLCT): production via enzymatic interesterification and optimization using response surface methodology (RSM).

PubMed

Lee, Yee-Ying; Tang, Teck-Kim; Phuah, Eng-Tong; Karim, Nur Azwani Ab; Alwi, Siti Maslina Mohd; Lai, Oi-Ming

2015-02-01

Structured lipid such as medium-and long-chain triacylglycerol (MLCT) is claimed to be able to suppress body fat accumulation and be used to manage obesity. Response surface methodology (RSM) with four factors and three levels (+1,0,-1) faced centered composite design (FCCD) was employed for optimization of the enzymatic interesterification conditions of palm-based MLCT (P-MLCT) production. The effect of the four variables namely: substrate ratio palm kernel oil: palm oil, PKO:PO (40:60-100:0 w/w), temperature (50-70 °C), reaction time (0.5-7.5 h) and enzyme load (5-15 % w/w) on the P-MLCT yield (%) and by products (%) produced were investigated. The responses were determined via acylglycerol composition obtained from high performance liquid chromatography. Well-fitted models were successfully established for both responses: P-MLCT yield (R (2) = 0.9979) and by-products (R (2) = 0.9892). The P-MLCT yield was significantly (P < 0.05) affected by substrate ratio, reaction time and reaction temperature but not enzyme load (P > 0.05). Substrate ratio PKO: PO (100:0 w/w) gave the highest yield of P-MLCT (61 %). Nonetheless, substrate ratio of PKO: PO (90:10w/w) was chosen to improve the fatty acid composition of the P-MLCT. The optimized conditions for substrate ratio PKO: PO (90:10 w/w) was 7.26 h, 50 °C and 5 % (w/w) Lipozyme TLIM lipase, which managed to give 60 % yields of P-MLCT. Up scaled results in stirred tank batch reactor gave similar yields as lab scale. A 20 % increase in P-MLCT yield was obtained via RSM. The effect of enzymatic interesterification on the physicochemical properties of PKO:PO (90:10 w/w) were also studied. Thermoprofile showed that the P-MLCT oil melted below body temperature of 37 °C.

Removal of Mercury by Foam Fractionation Using Surfactin, a Biosurfactant

PubMed Central

Chen, Hau-Ren; Chen, Chien-Cheng; Reddy, A. Satyanarayana; Chen, Chien-Yen; Li, Wun Rong; Tseng, Min-Jen; Liu, Hung-Tsan; Pan, Wei; Maity, Jyoti Prakash; Atla, Shashi B.

2011-01-01

The separation of mercury ions from artificially contaminated water by the foam fractionation process using a biosurfactant (surfactin) and chemical surfactants (SDS and Tween-80) was investigated in this study. Parameters such as surfactant and mercury concentration, pH, foam volume, and digestion time were varied and their effects on the efficiency of mercury removal were investigated. The recovery efficiency of mercury ions was highly sensitive to the concentration of the surfactant. The highest mercury ion recovery by surfactin was obtained using a surfactin concentration of 10 × CMC, while recovery using SDS required < 10 × CMC and Tween-80 >10 × CMC. However, the enrichment of mercury ions in the foam was superior with surfactin, the mercury enrichment value corresponding to the highest metal recovery (10.4%) by surfactin being 1.53. Dilute solutions (2-mg L−1 Hg2+) resulted in better separation (36.4%), while concentrated solutions (100 mg L−1) enabled only a 2.3% recovery using surfactin. An increase in the digestion time of the metal solution with surfactin yielded better separation as compared with a freshly-prepared solution, and an increase in the airflow rate increased bubble production, resulting in higher metal recovery but low enrichment. Basic solutions yielded higher mercury separation as compared with acidic solutions due to the precipitation of surfactin under acidic conditions. PMID:22174661

Removal of mercury by foam fractionation using surfactin, a biosurfactant.

PubMed

Chen, Hau-Ren; Chen, Chien-Cheng; Reddy, A Satyanarayana; Chen, Chien-Yen; Li, Wun Rong; Tseng, Min-Jen; Liu, Hung-Tsan; Pan, Wei; Maity, Jyoti Prakash; Atla, Shashi B

2011-01-01

The separation of mercury ions from artificially contaminated water by the foam fractionation process using a biosurfactant (surfactin) and chemical surfactants (SDS and Tween-80) was investigated in this study. Parameters such as surfactant and mercury concentration, pH, foam volume, and digestion time were varied and their effects on the efficiency of mercury removal were investigated. The recovery efficiency of mercury ions was highly sensitive to the concentration of the surfactant. The highest mercury ion recovery by surfactin was obtained using a surfactin concentration of 10 × CMC, while recovery using SDS required < 10 × CMC and Tween-80 >10 × CMC. However, the enrichment of mercury ions in the foam was superior with surfactin, the mercury enrichment value corresponding to the highest metal recovery (10.4%) by surfactin being 1.53. Dilute solutions (2-mg L(-1) Hg(2+)) resulted in better separation (36.4%), while concentrated solutions (100 mg L(-1)) enabled only a 2.3% recovery using surfactin. An increase in the digestion time of the metal solution with surfactin yielded better separation as compared with a freshly-prepared solution, and an increase in the airflow rate increased bubble production, resulting in higher metal recovery but low enrichment. Basic solutions yielded higher mercury separation as compared with acidic solutions due to the precipitation of surfactin under acidic conditions.

Combined alkaline hydrolysis and ultrasound-assisted extraction for the release of nonextractable phenolics from cauliflower (Brassica oleracea var. botrytis) waste.

PubMed

Gonzales, Gerard Bryan; Smagghe, Guy; Raes, Katleen; Van Camp, John

2014-04-16

Cauliflower waste contains high amounts phenolic compounds, but conventional solvent extraction misses high amounts of nonextractable phenolics (NEP), which may contribute more to the valorization of these waste streams. In this study, the NEP content and composition of cauliflower waste were investigated. The ability of alkaline hydrolysis, sonication, and their combination to release NEP was assessed. Alkaline hydrolysis with sonication was found to extract the highest NEP content (7.3 ± 0.17 mg gallic acid equivalents (GAE)/g dry waste), which was higher than the extractable fraction. The highest yield was obtained after treatment of 2 M NaOH at 60 °C for 30 min of sonication. Quantification and identification were done using U(H)PLC-DAD and U(H)PLC-ESI-MS(E). Kaempferol and quercetin glucosides along with several phenolic acids were found. The results of the study show that there are higher amounts of valuable health-promoting compounds from cauliflower waste than what is currently described in the literature.

Co-composting of palm oil mill sludge-sawdust.

PubMed

Yaser, Abu Zahrim; Abd Rahman, Rakmi; Kalil, Mohd Sahaid

2007-12-15

Composting of Palm Oil Mill Sludge (POMS) with sawdust was conducted in natural aerated reactor. Composting using natural aerated reactor is cheap and simple. The goal of this study is to observe the potential of composting process and utilizing compost as media for growing Cymbopogun citratus, one of Malaysia herbal plant. The highest maximum temperature achieved is about 40 degrees C and to increase temperature bed, more biodegradable substrate needs to be added. The pH value decrease along the process with final pH compost is acidic (pH 5.7). The highest maximum organic losses are about 50% with final C/N ratio of the compost is about 19. Final compost also showed some fertilizing value but need to be adjusted to obtain an ideal substrate. Addition of about 70% sandy soil causes highest yield and excellent root development for C. citratus in potted media. Beside that, compost from POMS-sawdust also found to have fertilizer value and easy to handle. Composting of POMS with sawdust shows potential as an alternative treatment to dispose and recycle waste components.

Characterization of Edible Pork By-products by Means of Yield and Nutritional Composition

PubMed Central

Moon, Sung Sil

2014-01-01

Basic information regarding the yield and nutritional composition of edible pork by-products, namely heart, liver, lung, stomach, spleen, uterus, pancreas, and small and large intestines, was studied. Our results revealed that the yields varied widely among the pork by-products examined; in particular, liver had the highest yield (1.35%); whereas, spleen had the lowest yield (0.16%). The approximate composition range (minimum to maximum) of these by-products was found to be: moisture 71.59-82.48%; fat 0.28-19.54%; ash 0.155-1.34%, and protein 8.45-22.05%. The highest protein, vitamin A, B2, B6, and total essential amino acid (EAA) contents were found in liver. Large intestine had the highest fat content and lowest EAA content. Heart had the highest vitamin B1 content, whereas pancreas had the highest niacin and vitamin B3 contents. The concentrations of Fe and Zn were highest in liver and pancreas. Total saturated fatty acids (SFA) levels and polyunsaturated fatty acids (PUFA) levels between the by-products ranged from 43.15-50.48%, and 14.92-30.16%, respectively. Furthermore, with the exception of large intestine, all the by-products showed favorable PUFA/SFA ratios. The study indicated that almost all of the pork by-products examined were good sources of important nutrients, and that these data will be of great importance in the promotion of the consumption of edible pork by-products, as well as their utilization in meat processing. PMID:26761170

Rate contants for CF{sub 3} + H{sub 2} {yields} CF{sub 3}H + H and CF{sub 3}H + H {yields} CF{sub 3} + H{sub 2} reactions in the temperature range 1100-1600 K.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hranisavljevic, J.; Michael, V.; Chemistry

1998-09-24

The shock tube technique coupled with H-atom atomic resonance absorption spectrometry has been used to study the reactions (1) CF{sub 3} + H{sub 2} {yields} CF{sub 3}H + H and (2) CF{sub 3}H + H{yields} CF{sub 3} + H{sub 2} over the temperature ranges 1168-1673 K and 1111-1550 K, respectively. The results can be represented by the Arrhenius expressions k1 = 2.56 x 10{sup -11} exp(-8549K/T) and k2 = 6.13 x 10{sup -11} exp(-7364K/T), both in cm3 molecule-1 s-1. Equilibrium constants were calculated from the two Arrhenius expressions in the overlapping temperature range, and good agreement was obtained with themore » literature values. The rate constants for reaction 2 were converted into rate constants for reaction 1 using literature equilibrium constants. These data are indistinguishable from direct k1 measurements, and an Arrhenius fit for the joint set is k{sub 1} = 1.88 x 10{sup -11} exp(-8185K/T) cm3 molecule-1 s-1. The CF{sub 3} + H{sub 2} {yields} CF{sub 3}H + H reaction was further modeled using conventional transition-state theory, which included ab initio electronic structure determinations of reactants, transition state, and products.« less

Studies on the key aroma compounds in raw (unheated) and heated Japanese soy sauce.

PubMed

Kaneko, Shu; Kumazawa, Kenji; Nishimura, Osamu

2013-04-10

An investigation using the aroma extract dilution analysis (AEDA) technique of the aroma concentrate from a raw Japanese soy sauce and the heated soy sauce revealed 40 key aroma compounds including 7 newly identified compounds. Among them, 5(or 2)-ethyl-4-hydroxy-2(or 5)-methyl-3(2H)-furanone and 3-hydroxy-4,5-dimethyl-2(5H)-furanone exhibited the highest flavor dilution (FD) factor of 2048, followed by 3-(methylthio)propanal, 4-ethyl-2-methoxyphenol, and 4-hydroxy-2,5-dimethyl-3(2H)-furanone having FD factors from 128 to 512 in the raw soy sauce. Furthermore, comparative AEDAs, a quantitative analysis, and a sensory analysis demonstrated that whereas most of the key aroma compounds in the raw soy sauce were common in the heated soy sauce, some of the Strecker aldehydes and 4-vinylphenols contributed less to the raw soy sauce aroma. The model decarboxylation reactions of the phenolic acids during heating of the raw soy sauce revealed that although all reactions resulted in low yields, the hydroxycinnamic acid derivatives were much more reactive than the hydroxybenzoic acid derivatives due to the stable reaction intermediates. Besides the quantitative analyses of the soy sauces, the estimation of the reaction yields of the phenolic compounds in the heated soy sauce revealed that although only the 4-vinylphenols increased during heating of the raw soy sauce, they might not mainly be formed as decarboxylation products from the corresponding hydroxycinnamic acids but from the other proposed precursors, such as lignin, shakuchirin, and esters with arabinoxylan.

Influence of quantum dot's quantum yield to chemiluminescent resonance energy transfer.

PubMed

Wang, Hai-Qiao; Li, Yong-Qiang; Wang, Jian-Hao; Xu, Qiao; Li, Xiu-Qing; Zhao, Yuan-Di

2008-03-03

The resonance energy transfer between chemiluminescence donor (luminol-H2O2 system) and quantum dots (QDs, emission at 593 nm) acceptors (CRET) was investigated. The resonance energy transfer efficiencies were compared while the oil soluble QDs, water soluble QDs (modified with thioglycolate) and QD-HRP conjugates were used as acceptor. The fluorescence of QD can be observed in the three cases, indicating that the CRET occurs while QD acceptor in different status was used. The highest CRET efficiency (10.7%) was obtained in the case of oil soluble QDs, and the lowest CRET efficiency (2.7%) was observed in the QD-HRP conjugates case. This result is coincident with the quantum yields of the acceptors (18.3% and 0.4%). The same result was observed in another similar set of experiment, in which the amphiphilic polymer modified QDs (emission at 675 nm) were used. It suggests that the quantum yield of the QD in different status is the crucial factor to the CRET efficiency. Furthermore, the multiplexed CRET between luminol donor and three different sizes QD acceptors was observed simultaneously. This work will offer useful support for improving the CRET studies based on quantum dots.

Passage of stable isotope-labeled grass silage fiber and fiber-bound protein through the gastrointestinal tract of dairy cows.

PubMed

Warner, D; Dijkstra, J; Hendriks, W H; Pellikaan, W F

2013-01-01

Fractional passage rates are required to predict nutrient absorption in ruminants but data on nutrient-specific passage kinetics are largely lacking. With the use of the stable isotope ratio (δ) as an internal marker, we assessed passage kinetics of fiber and fiber-bound nitrogen (N) of intrinsically labeled grass silage from fecal and omasal excretion patterns of δ(13)C and δ(15)N. In a 6×6 Latin square, lactating dairy cows received grass silages [455 g/kg of total diet dry matter (DM) ] in a 2×3 factorial arrangement from ryegrass swards fertilized at low (45 kg of N/ha) or high (90 kg of N/ha) levels of N and harvested at 3 maturity stages. Feed intake (16.7±0.48 kg of DM/d; mean ± standard error of the mean) and milk yield (26.7±0.92 kg/d) increased at the high level of N fertilization and at decreasing maturity. Nutrient digestibility decreased with increasing plant maturity, particularly at the high level of N fertilization, essentially reflecting dietary treatment effects on the nutritional composition of the grass silage. Fractional rumen passage rates (K1) were highest and total mean retention time in the gastrointestinal tract (TMRT) was lowest when based on the external marker chromium mordanted fiber (Cr-NDF; 0.047/h and 38.0 h, respectively). Fecal δ(13)C in the acid detergent fiber fraction ((13)CADF) provided the lowest K1 (0.023/h) and the highest TMRT (61.1 h) and highest peak concentration time (PCT; 24.3h) among markers. In comparison, fecal fiber-bound N ((15)NADF) had a considerably higher K1 (0.032/h) and lower TMRT (46.4 h) than (13)CADF. Total N (measured with (15)NDM) had a comparable K1 (0.034/h) to that of (15)NADF but provided the highest fractional passage rates from the proximal colon-cecum (K2; 0.37/h) and lowest PCT (17.4 h) among markers. A literature review indicated unclear effects of grass silage maturity on K1 and unknown effects of N fertilization on K1. Our study indicated no effect of advancing maturity on fecal K1 and a trend for K1 to increase with the high level of N fertilization. Parameter K2 increased, whereas PCT and TMRT generally decreased with the high level of N fertilization. Omasal digesta sampling largely confirmed results based on fecal sampling. Results indicate that the use of δ(13)C and δ(15)N can describe fiber-specific passage kinetics of forage. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

A comparison of three pH control methods for revealing effects of undissociated butyric acid on specific butanol production rate in batch fermentation of Clostridium acetobutylicum.

PubMed

Yang, Xuepeng; Tu, Maobing; Xie, Rui; Adhikari, Sushil; Tong, Zhaohui

2013-01-07

pH control has been essential for butanol production with Clostridium acetobutylicum. However, it is not very clear at what pH level the acid crash will occur, at what pH level butanol production will be dominant, and at what pH level butyric acid production will be prevailing. Furthermore, contradictory results have been reported about required acidic conditions for initiation of solventogenesis. In this study, with the aim of further understanding the role of undissociated butyric acid in butanol production, we investigated the correlation between undissociated butyric acid concentration and specific butanol production rate in batch fermentation of Clostridium acetobutylicum by comparing three pH control approaches: NaOH neutralization (at 12, 24 or 36 h), CaCO3 supplementation (2, 5, or 8 g/l) and NaOAc buffering (pH 4.6, 5.0 or 5.6). By neutralizing the fermentation pH to ~5.0 at different time, we observed that neutralization should take place at the beginning of exponential phase (12 h), and otherwise resulting in lower concentrations of undissociated butyric acid, cell biomass and final butanol. CaCO3 supplementation extended cell growth to 36 h and resulted in higher butyrate yield under 8 g/L of CaCO3. In the NaOAc buffering, the highest specific butanol rate (0.58 h-1) was associated with the highest undissociated butyric acid (1.92 g/L). The linear correlation of the undissociated butyric acid with the specific butanol production rates suggested the undissociated butyric acid could be the major driving force for butanol production.

Hot-boning enhances cook yield of boneless skinless chicken thighs.

PubMed

Zhuang, H; Bowker, B C; Buhr, R J; Brambila, G Sanchez

2014-06-01

Three experiments were conducted to evaluate the effects of postmortem deboning time on cook yield of boneless skinless chicken thighs. In experiment 1, chicken thigh meat was deboned at 0.75 (hot-bone), 2, and 24 h postmortem (PM) and trimmed to obtain mainly iliotibialis muscle. Samples were cooked directly from a frozen state. Cook yield of the muscle was significantly influenced by PM deboning time. Hot-boned thighs exhibited a 7% greater cook yield than the samples deboned at 24 h. In experiment 2, boneless skinless chicken thighs were deboned at 0.3, 2, and 24 h PM and cooked directly from a fresh, never-frozen state at 24 h PM. Cook yield of the hot-boned thighs was significantly higher than those of the 2 and 24 h deboned samples, which did not differ from each other. In experiment 3, whole legs (thigh + drumstick) were cut from the carcass backbone at 0.3 (hot-cut), 2, and 24 h PM. Thighs were separated from the legs (drumsticks) at either the same time the whole legs were removed from the carcasses or at 24 h PM. Intact thighs (bone in) were cooked fresh at 24 h PM. Color of fresh thigh muscles, cook yield, and Warner-Bratzler shear force of cooked samples were measured. Cook yield of the thighs cut from the backbone before chilling was significantly higher than those cut from the carcasses at 2 and 24 h PM, which did not differ from each other. The PM time at which intact thighs were separated from the leg (drumstick) did not influence cook yield. These results demonstrate that postmortem deboning time can significantly affect cook yield of boneless skinless chicken thigh products. Deboning chicken thighs after chilling reduces the cook yield. Differences in the cook yield of thighs may also result from the removal of whole chicken legs from the carcass backbone. Poultry Science Association Inc.

Extracellular Alkaline Lipase from a Novel Fungus
Curvularia sp. DHE 5: Optimisation of Physicochemical Parameters, Partial Purification and Characterisation

PubMed Central

2017-01-01

Summary Thirty isolated fungal strains were screened for lipase production using Phenol Red plates, containing tributyrin as lipidic substrate, and a novel fungus identified genetically as Curvularia sp. DHE 5 was found as the most prominent strain. Various agro-industrial substrates were evaluated as inert supports for lipase production in solid-state fermentation. The highest yield of lipase ((83.4±2.2) U/g on dry mass basis) was reported with wheat bran medium after seven days of fermentation at pH=7.0, temperature of 30 °C, 70% moisture content, inoculum size of 1.27·107 spore/mL and 2% olive oil as an inducer. Supplementation of the medium with 0.05% KCl as an ion source further increased lipase production to (88.9±1.2) U/g on dry mass basis. The enzyme was partially purified through ammonium sulphate fractionation (40%) followed by dialysis, and its optimum pH and temperature were reported at 8.0 and 50 °C, respectively, with remarkable pH and thermal stability. PMID:28867950

Oxygen-Centered Hexatantalum Tetradecaimido Cluster Complexes

PubMed Central

Krinsky, Jamin L.; Anderson, Laura L.; Arnold, John; Bergman, Robert G.

2008-01-01

The syntheses and characterization of several octahedral hexatantalum cluster compounds of formula (ArN)14Ta6O are described (Ar = Ph, p-MeC6H4, p-MeOC6H4, p-t-BuC6H4, p-BrC6H4, m-ClC6H4). Treatment of Bn3Ta=N-t-Bu (Bn = CH2C6H5) or pentakis(dimethylamido)tantalum with an excess of the appropriate aniline and stoichiometric water or tantalum oxide afforded varying yields of arylimido clusters. The structures of two species were confirmed by X-ray diffraction (XRD), while the identity of the central oxygen atom was elucidated by electrospray mass spectrometry (MS) using 17O/18O-enriched material. The title species are very air- and moisture-sensitive but quite thermally stable in solution. Experimentally determined optical properties and oxidation/reduction potentials, as well as some computational results, indicate that they possess an electronic structure wherein the highest occupied molecular orbitals are ligand-centered, while the lowest unoccupied orbitals are metal-centered and delocalized throughout the tantalum cage. Whereas chemical oxidation resulted in cluster decomposition, reduction with decamethylcobaltocene yielded stable salts of formula [Cp*2Co][(ArN)14Ta6O] (Ar = Ph, Ar = p-MeC6H4). Small-molecule reactivity studies on one of these clusters showed that its imido functionalities are moderately reactive toward oxide donors but inert with respect to metallaheterocycle-forming processes. Clean imido/oxo exchange was observed with aldehydes and ketones, leading cleanly to organic imines with no soluble byproducts being observed. This exchange was also observed with a rhenium oxo compound (generating an imidorhenium complex as the only soluble species). All 14 imido groups were transferred in these reactions, and no mixed-ligand cluster intermediates were ever observed. PMID:18163614

The pH dependency of N-converting enzymatic processes, pathways and microbes: effect on net N2 O production.

PubMed

Blum, Jan-Michael; Su, Qingxian; Ma, Yunjie; Valverde-Pérez, Borja; Domingo-Félez, Carlos; Jensen, Marlene Mark; Smets, Barth F

2018-05-01

Nitrous oxide (N 2 O) is emitted during microbiological nitrogen (N) conversion processes, when N 2 O production exceeds N 2 O consumption. The magnitude of N 2 O production vs. consumption varies with pH and controlling net N 2 O production might be feasible by choice of system pH. This article reviews how pH affects enzymes, pathways and microorganisms that are involved in N-conversions in water engineering applications. At a molecular level, pH affects activity of cofactors and structural elements of relevant enzymes by protonation or deprotonation of amino acid residues or solvent ligands, thus causing steric changes in catalytic sites or proton/electron transfer routes that alter the enzymes' overall activity. Augmenting molecular information with, e.g., nitritation or denitrification rates yields explanations of changes in net N 2 O production with pH. Ammonia oxidizing bacteria are of highest relevance for N 2 O production, while heterotrophic denitrifiers are relevant for N 2 O consumption at pH > 7.5. Net N 2 O production in N-cycling water engineering systems is predicted to display a 'bell-shaped' curve in the range of pH 6.0-9.0 with a maximum at pH 7.0-7.5. Net N 2 O production at acidic pH is dominated by N 2 O production, whereas N 2 O consumption can outweigh production at alkaline pH. Thus, pH 8.0 may be a favourable pH set-point for water treatment applications regarding net N 2 O production. © 2018 Society for Applied Microbiology and John Wiley & Sons Ltd.

Improvement of the respiration efficiency of Lactococcus lactis by decreasing the culture pH.

PubMed

Shi, Weijia; Li, Yu; Gao, Xueling; Fu, Ruiyan

2016-03-01

The growth characteristics and intracellular hemin concentrations of Lactococcus lactis grown under different culture pH and aeration conditions were examined to investigate the effect of culture pH on the respiration efficiency of L. lactis NZ9000 (pZN8148). Cell biomass and biomass yield of L. lactis grown with 4 μg hemin/ml and O2 were higher than those without aeration when the culture pH was controlled at 5-6.5. The culture pH affected the respiratory efficiency in the following order of pH: 5 > 5.5 > 6 > 6.5; the lag phase increased as the culture pH decreased. Hemin accumulation was sensitive to culture pH. Among the four pH conditions, pH 5.5 was optimal for hemin accumulation in the cells. The highest intracellular hemin level in L. lactis resting cells incubated at different pH saline levels (5-6.5) was at pH 5.5. The respiration efficiency of L. lactis under respiration-permissive conditions increases markedly as the culture pH decreases. These results may help develop high cell-density L. lactis cultures. Thus, this microorganism may be used for industrial applications.

Harnessing fertilizer potential of human urine in a mesocosm system: a novel test case for linking the loop between sanitation and aquaculture.

PubMed

Rana, Sukanta; Biswas, Jayanta Kumar; Rinklebe, Jörg; Meers, Erik; Bolan, Nanthi

2017-12-01

Human urine (HU) is a biogenic fertilizer which has raised immense interest owing to its capacity of combining sanitation and nutrient recovery. In search of an alternative organic fertilizer for fish culture, the nutrient potential of HU was evaluated. Fries of Indian carps and larvae of freshwater prawn were reared for 120 days under six conditions: (a) aerated and (b) non-aerated fresh HU (0.01%), (c) cattle manure (CM; 1.8 kg tank -1 ), mixed treatment with CM and HU under (d) iso-phosphorus and (e) iso-nitrogenous condition and (f) control. Monitoring of water quality and biological parameters revealed that total fish yield was the highest in CM (621.5 g tank -1 ) followed by mixed treatments under iso-nitrogenous (428 g tank -1 ) and iso-phosphorus (333 g tank -1 ) conditions, aerated HU (321 g tank -1 ) and HU (319 g tank -1 ). The gross primary productivity (GPP) in HU was satisfactory (601.8 mg C m -2  h -1 ) and superior to all but CM treatment. The abundance of heterotrophic bacteria (HB) was highest in CM and lowest in HU. Both GPP and HB population were correlated positively with fish yield per tank. Although pH in all treatments remained high (pH 8.4-8.9), no ammonia toxicity was observed. No E. coli infestation in any fish muscle was encountered. The concentrations of cadmium and lead in fish muscle were within respective safe level. The study established that high fertilizer potential of HU could be exploited as an alternative organic fertilizer or as a candidate to be blended with cattle manure.

CVD of SiC and AlN using cyclic organometallic precursors

NASA Technical Reports Server (NTRS)

Interrante, L. V.; Larkin, D. J.; Amato, C.

1992-01-01

The use of cyclic organometallic molecules as single-source MOCVD precursors is illustrated by means of examples taken from our recent work on AlN and SiC deposition, with particular focus on SiC. Molecules containing (AlN)3 and (SiC)2 rings as the 'core structure' were employed as the source materials for these studies. The organoaluminum amide, (Me2AlNH2)3, was used as the AlN source and has been studied in a molecular beam sampling apparatus in order to determine the gas phase species present in a hot-wall CVD reactor environment. In the case of SiC CVD, a series of disilacyclobutanes (Si(XX')CH2)2 (with X and X' = H, CH3, and CH2SiH2CH3), were examined in a cold-wall, hot-stage CVD reactor in order to compare their relative reactivities and prospective utility as single-source CVD precursors. The parent compound, disilacyclobutane, (SiH2CH2)2, was found to exhibit the lowest deposition temperature (ca. 670 C) and to yield the highest purity SiC films. This precursor gave a highly textured, polycrystalline film on the Si(100) substrates.

Optimized conditions for chelation of yttrium-90-DOTA immunoconjugates.

PubMed

Kukis, D L; DeNardo, S J; DeNardo, G L; O'Donnell, R T; Meares, C F

1998-12-01

Radioimmunotherapy (RIT) with 90Y-labeled immunoconjugates has shown promise in clinical trials. The macrocyclic chelating agent 1,4,7,10-tetraazacyclododecane-N,N',N",N"'-tetraacetic acid (DOTA) binds 90Y with extraordinary stability, minimizing the toxicity of 90Y-DOTA immunoconjugates arising from loss of 90Y to bone. However, reported 90Y-DOTA immunoconjugate product yields have been typically only < or =50%. Improved yields are needed for RIT with 90Y-DOTA immunoconjugates to be practical. (S) 2-[p-(bromoacetamido)benzyl]-DOTA (BAD) was conjugated to the monoclonal antibody Lym-1 via 2-iminothiolane (2IT). The immunoconjugate product, 2IT-BAD-Lym-1, was labeled in excess yttrium in various buffers over a range of concentrations and pH. Kinetic studies were performed in selected buffers to estimate radiolabeling reaction times under prospective radiopharmacy labeling conditions. The effect of temperature on reaction kinetics was examined. Optimal radiolabeling conditions were identified and used in eight radiolabeling experiments with 2IT-BAD-Lym-1 and a second immunoconjugate, DOTA-peptide-chimeric L6, with 248-492 MBq (6.7-13.3 mCi) of 90Y. Ammonium acetate buffer (0.5 M) was associated with the highest uptake of yttrium. On the basis of kinetic data, the time required to chelate 94% of 90Y (four half-times) under prospective radiopharmacy labeling conditions in 0.5 M ammonium acetate was 17-148 min at pH 6.5, but it was only 1-10 min at pH 7.5. Raising the reaction temperature from 25 degrees C to 37 degrees C markedly increased the chelation rate. Optimal radiolabeling conditions were identified as: 30-min reaction time, 0.5 M ammonium acetate buffer, pH 7-7.5 and 37 degrees C. In eight labeling experiments under optimal conditions, a mean product yield (+/- s.d.) of 91%+/-8% was achieved, comparable to iodination yields. The specific activity of final products was 74-130 MBq (2.0-3.5 mCi) of 90Y per mg of monoclonal antibody. The immunoreactivity of 90Y-labeled immunoconjugates was 100%+/-11%. The optimization of 90Y-DOTA chelation conditions represents an important advance in 90Y RIT because it facilitates the dependable and cost-effective preparation of 90Y-DOTA pharmaceuticals.

Surfactant assisted disperser pretreatment on the liquefaction of Ulva reticulata and evaluation of biodegradability for energy efficient biofuel production through nonlinear regression modelling.

PubMed

Kumar, M Dinesh; Tamilarasan, K; Kaliappan, S; Banu, J Rajesh; Rajkumar, M; Kim, Sang Hyoun

2018-05-01

The present study aimed to increase the disintegration potential of marine macroalgae, (Ulva reticulata) through chemo mechanical pretreatment (CMP) in an energy efficient manner. By combining surfactant with disperser, the specific energy input was considerably reduced from 437.1 kJ/kg TS to 264.9 kJ/kg TS to achieve 10.7% liquefaction. A disperser rpm (10,000), pretreatment time (30 min) and tween 80 dosage (21.6 mg/L) were considered as an optimum for effective liquefaction of algal biomass. CMP was designated as an appropriate pretreatment resulting in a higher soluble organic release 1250 mg/L, respectively. Anaerobic fermentation results revealed that the volatile fatty acid (VFA) concentration was doubled (782 mg/L) in CMP when compared to mechanical pretreatment (MP) (345 mg/L). CMP pretreated algal biomass was considered as the suitable for biohydrogen production with highest H 2 yield of about 63 mL H 2 /g COD than (MP) (45 mL H 2 /g COD) and control (10 mL H 2 /g COD). Copyright © 2018 Elsevier Ltd. All rights reserved.

Rate Coefficients for Reactions of Ethynyl Radical (C2H) With HCN and CH3CN: Implications for the Formation of Comples Nitriles on Titan

NASA Technical Reports Server (NTRS)

Hoobler, Ray J.; Leone, Stephen R.

1997-01-01

Rate coefficients for the reactions of C2H + HCN yields products and C2H + CH3CN yields products have been measured over the temperature range 262-360 K. These experiments represent an ongoing effort to accurately measure reaction rate coefficients of the ethynyl radical, C2H, relevant to planetary atmospheres such as those of Jupiter and Saturn and its satellite Titan. Laser photolysis of C2H2 is used to produce C2H, and transient infrared laser absorption is employed to measure the decay of C2H to obtain the subsequent reaction rates in a transverse flow cell. Rate constants for the reaction C2H + HCN yields products are found to increase significantly with increasing temperature and are measured to be (3.9-6.2) x 10(exp 13) cm(exp 3) molecules(exp -1) s(exp -1) over the temperature range of 297-360 K. The rate constants for the reaction C2H + CH3CN yields products are also found to increase substantially with increasing temperature and are measured to be (1.0-2.1) x 10(exp -12) cm(exp 3) molecules(exp -1) s(exp -1) over the temperature range of 262-360 K. For the reaction C2H + HCN yields products, ab initio calculations of transition state structures are used to infer that the major products form via an addition/elimination pathway. The measured rate constants for the reaction of C2H + HCN yields products are significantly smaller than values currently employed in photochemical models of Titan, which will affect the HC3N distribution.

Preparation of CaO/Fly ash as a catalyst inhibitor for transesterification process off palm oil in biodiesel production

NASA Astrophysics Data System (ADS)

Helwani, Z.; Fatra, W.; Saputra, E.; Maulana, R.

2018-03-01

A palm fly ash supported calcium oxide (CaO) catalyst was prepared and used in transesterification from off-grade palm oil for biodiesel production. The catalyst synthesized by loading CaO of calcium nitrate tetrahydrate (Ca(NO3)2.4H2O) into fly ash through impregnation method. The optimum catalyst preparation conditions were determined by influence of calcination temperature and weight ratio of Ca(NO3)2.4H2O and fly ash. Catalyst with highest catalytic activity was achieved when calcined at 800 °C and proportion of Ca(NO3)2.4H2O to fly ash is 80:20. Under the conditions of oil : methanol ratio of 1:6, catalyst dosage of 6 wt% and temperature of 70 °C for 2 h, the biodiesel yield reaches to 71.77%. CaO, SiO2, Ca(OH)2 and Ca2SiO4 were found in the catalyst through X-ray diffraction (XRD) while the basic strength of the catalyst H_ in the range 9.3 – 11. Surface area of the developed catalyst is 24.342 m2/g through Brunauer-Emmett-Teller (BET). Characteristics of biodiesel such as density, kinematic viscosity, acid value, flash point has been matched with standard for biodiesel specification of Indonesia.

Effect of the length of the cycle on biodegradable polymer production and microbial community selection in a sequencing batch reactor.

PubMed

Dionisi, Davide; Majone, Mauro; Vallini, Giovanni; Gregorio, Simona Di; Beccari, Mario

2007-01-01

The effect of the length of the cycle on the enrichment and selection of mixed cultures in sequencing batch reactors (SBRs) has been studied, with the aim of biodegradable polymers (namely, polyhydroxyalkanoates (PHAs)) production from organic wastes. At a fixed feed concentration (20 gCOD/L) and organic loading rate (20 gCOD/L/day), the SBR was operated at different lengths of the cycle, in the range 1-8 h. Process performance was measured by considering the rates and yields of polymer storage and of the competing phenomenon of growth. The selected biomass was enriched with microorganisms that were able to store PHAs at high rates and yields only when the length of the cycle was 2 or 4 h, even though in these conditions the process was unstable. On the other hand, when the length of the cycle was 1 or 8 h, the dynamic response of the selected microorganisms was dominated by growth. The best process performance was characterized by storage rates in the range 500-600 mgCOD/gCOD/h and storage yields of 0.45-0.55 COD/COD. The corresponding productivity of the process was in the range 0.25-0.30 gPHA/L/h, the highest values obtained until now for mixed cultures. The microbial composition of the selected biomasses was analyzed through denaturing gradient gel electrophoresis (DGGE) and reverse-transcriptase denaturing gradient gel electrophoresis (RT-DGGE). The instability of the runs characterized by high storage rate was associated with a higher microbial heterogeneity compared to the runs with a stable growth response.

A continental scale model for dissolved silica mobilization in North America

NASA Astrophysics Data System (ADS)

Jansen, N.; Lauerwald, R.; Hartmann, J.; Dürr, H. H.; Loos, S.; Kempe, S.; Middelkoop, H.

2009-04-01

Silicon is one of the few elements that link to both the organic and inorganic carbon cycles. Dissolved silicon (DSi) is an important nutrient in terrestrial and aquatic ecosystems. Cations accompanying the release of DSi by chemical silicate rock weathering are generally balanced by soil/atmospheric CO2. Chemical weathering is the major source of "new" bioavailable DSi for continental aquatic systems to compensate for the loss of DSi by outflow or organic precipitation and burial. We use river water chemistry data from 164 monitoring stations from the conterminous United States (WQN and NAWQA networks). Selected stations are characterized by low population density and low influence of water bodies to minimize human and DSi retention impact. Observed DSi yield in these catchments is assumed to represent natural DSi mobilization by chemical weathering. The catchments have an average size of 4400 km2 (Median: 991 km2) with a discharge weighted average DSi yield of 4.34 t SiO2 km-2a-1. To predict mobilization of DSi from chemical weathering a lumped non-linear empirical model is developed, considering control factors such as climate, morphology, hydrology, land cover, soil and lithology. A multi-lithological model approach is chosen because only very few mono-lithological catchments were identified in the dataset. The model is then extrapolated to the conterminous United States to regionally quantify the amount of DSi that is released into the river systems by chemical weathering. Small outcrops of certain lithological classes characterized by a high DSi yield are not represented on previously available small scale lithological maps. Because such localities may have a major influence on DSi fluxes from small catchments (Hartmann et al., 2009) a new high resolution lithological vector-map for North America is developed and applied in the introduced model. In accordance with previous studies, runoff and lithology are identified as the major predictors for specific DSi flux (Bluth and Kump, 1994; Hartmann et al., 2009). Only in relation to some lithological classes, temperature and terrain slope constitute significant predictors. An influence of land cover, soil properties or other predictors is not observed. This is partly attributed to geodata resolution and classification. Lithological classes "Basic Volcanics and Pyroclastics" and "Basic and Intermediate Plutonics" show the highest DSi yields, with respect to a given discharge. The lithological class "Siliciclastic Sedimentary Rocks" is characterized by the lowest DSi yield. The model explains 89% of the DSi yield variance; the average yield of catchments employed in model calibration is 4.32 t SiO2 km-2a-1, somewhat above the global average yield of 3.3 t SiO2 km-2a-1 (Dürr et al., 2009). The model quantifies DSi fluxes from the terrestrial into the continental aquatic systems. This helps to estimate DSi retention within fluvial systems (Lauerwald et al., submitted) and improves understanding of this part of the silicon cycle. References: Bluth, G.J.S., and Kump, L.R., 1994, Lithologic and Climatologic Controls of River Chemistry: Geochimica Cosmochimica Acta, 58, 2341-2359. Dürr, H.H., Meybeck, M., Hartmann, J., Laruelle, G.G., and Roubeix, V., 2009, Global Spatial distribution of natural riverine silica inputs to the coastal zone: Biogeosciences, (in review), bgd-2008-0173. Hartmann, J., Jansen, N., Dürr, H.H., Harashima, A., Okubo, K., and Kempe, S., 2009, Predicting riverine dissolved silica fluxes into coastal zones from a hyperactive region and analysis of their first order controls: International Journal of Earth Sciences, (DOI 10.1007/s00531-008-0381-5). Lauerwald, R., Jansen N., Hartmann, J., Dürr, H.H., Loos, S., Kempe, S., Middelkoop, H., submitted, Modeling dissolved silica retention in the limnic system of North America. (Submitted to this session).

Spectrophotometric evaluation of selenium binding by Saccharomyces cerevisiae ATCC MYA-2200 and Candida utilis ATCC 9950 yeast.

PubMed

Kieliszek, Marek; Błażejak, Stanisław; Płaczek, Maciej

2016-05-01

In this study, the ability of selenium binding the biomas of Saccharomyces cerevisiae ATCC MYA-2200 and Candida utilis ATCC 9950 was investigated. Sodium selenite(IV) salts were added to the experimental media at concentrations of 10, 20, 40, and 60 mg Se(4+) L(-1). In the tested concentration range, one concentration reported a significant reduction in the biomass yield of both yeast strains. Intense growth was observed for C. utilis yeast, which reached the highest biomass yield of 15 gd.w.L(-1) after 24h cultivation in the presence of 10mg Se(4+) L(-1). Based on the use of spectrophotometric method for the determination of selenium content by using Variamine Blue as a chromogenic agent, efficient accumulation of this element in the biomass of the investigated yeast was observed. The highest amount of selenium, that is, 5.64 mg Se(4+)gd.w.(-1), was bound from the environment by S. cerevisiae ATCC MYA-2200 cultured in the presence of 60 mg Se(4+) L(-1) medium 72h Slightly less amount, 5.47 mg Se(4+) gd.w.(-1), was absorbed by C. utilis ATCC 9950 during similar cultural conditions. Based on the results of the biomass yield and the use of selenium from the medium, it can be observed that yeasts of the genus Candida are more efficient in binding this element, and this property finds practical application in the production of selenium-enriched yeast. Copyright © 2016 Elsevier GmbH. All rights reserved.

A comparison of three pH control methods for revealing effects of undissociated butyric acid on specific butanol production rate in batch fermentation of Clostridium acetobutylicum

PubMed Central

2013-01-01

pH control has been essential for butanol production with Clostridium acetobutylicum. However, it is not very clear at what pH level the acid crash will occur, at what pH level butanol production will be dominant, and at what pH level butyric acid production will be prevailing. Furthermore, contradictory results have been reported about required acidic conditions for initiation of solventogenesis. In this study, with the aim of further understanding the role of undissociated butyric acid in butanol production, we investigated the correlation between undissociated butyric acid concentration and specific butanol production rate in batch fermentation of Clostridium acetobutylicum by comparing three pH control approaches: NaOH neutralization (at 12, 24 or 36 h), CaCO3 supplementation (2, 5, or 8 g/l) and NaOAc buffering (pH 4.6, 5.0 or 5.6). By neutralizing the fermentation pH to ~5.0 at different time, we observed that neutralization should take place at the beginning of exponential phase (12 h), and otherwise resulting in lower concentrations of undissociated butyric acid, cell biomass and final butanol. CaCO3 supplementation extended cell growth to 36 h and resulted in higher butyrate yield under 8 g/L of CaCO3. In the NaOAc buffering, the highest specific butanol rate (0.58 h−1) was associated with the highest undissociated butyric acid (1.92 g/L). The linear correlation of the undissociated butyric acid with the specific butanol production rates suggested the undissociated butyric acid could be the major driving force for butanol production. PMID:23294525

Beta-glucan production by Botryosphaeria rhodina in different bench-top bioreactors.

PubMed

Selbmann, L; Crognale, S; Petruccioli, M

2004-01-01

Evaluation of the technical feasibility of transferring beta-glucan production by Botryosphaeria rhodina DABAC-P82 from shaken flasks to bench-top bioreactors. Three different bioreactors were used: 3 l stirred tank reactor (STR-1) equipped with two different six-blade turbines; STR as above but equipped with a three-blade marine propeller plus draft-tube (STR-2); 2 l air-lift column reactor (ALR) equipped with an external loop. STR-1, tested at three different stirrer speeds (300, 500 and 700 rev min(-1)) appeared to be less suitable for beta-glucan production by the fungus, being maximum production (19.4 g l(-1)), productivity (0.42 g l(-1) h(-1)) and yield (0.48 g g(-1) of glucose consumed) markedly lower than those obtained in shaken culture (29.7 g l(-1), 1.23 g l(-1) h(-1) and 0.61 g g(-1), respectively). Better performances were obtained with both STR-2 and ALR. With the latter, in particular, the increase of production was accompanied by reduced fermentation time (25.7 g l(-1) after only 22 h); productivity and yield were highest (1.17 g l(-1) h(-1) and 0.62 g g(-1) of glucose consumed, respectively). Using an air-lift reactor with external loop, the scaling up from shaken flasks to bench-top bioreactor of the beta-glucan production by B. rhodina DABAC-P82 is technically feasible. Although culture conditions are still to be optimized, the results obtained using the ARL are highly promising.

Calculational and Experimental Investigations of the Pressure Effects on Radical - Radical Cross Combinations Reactions: C2H5 + C2H3

NASA Technical Reports Server (NTRS)

Fahr, Askar; Halpern, Joshua B.; Tardy, Dwight C.

2007-01-01

Pressure-dependent product yields have been experimentally determined for the cross-radical reaction C2H5 + C2H3. These results have been extended by calculations. It is shown that the chemically activated combination adduct, 1-C4H8*, is either stabilized by bimolecular collisions or subject to a variety of unimolecular reactions including cyclizations and decompositions. Therefore the "apparent" combination/disproportionation ratio exhibits a complex pressure dependence. The experimental studies were performed at 298 K and at selected pressures between about 4 Torr (0.5 kPa) and 760 Torr (101 kPa). Ethyl and vinyl radicals were simultaneously produced by 193 nm excimer laser photolysis of C2H5COC2H3 or photolysis of C2H3Br and C2H5COC2H5. Gas chromatograph/mass spectrometry/flame ionization detection (GC/MS/FID) were used to identify and quantify the final reaction products. The major combination reactions at pressures between 500 (66.5 kPa) and 760 Torr are (1c) C2H5 + C2H3 yields 1-butene, (2c) C2H5 + C2H5 yields n-butane, and (3c) C2H3 + C2H3 yields 1,3-butadiene. The major products of the disproportionation reactions are ethane, ethylene, and acetylene. At moderate and lower pressures, secondary products, including propene, propane, isobutene, 2-butene (cis and trans), 1-pentene, 1,4-pentadiene, and 1,5-hexadiene are also observed. Two isomers of C4H6, cyclobutene and/or 1,2-butadiene, were also among the likely products. The pressure-dependent yield of the cross-combination product, 1-butene, was compared to the yield of n-butane, the combination product of reaction (2c), which was found to be independent of pressure over the range of this study. The [ 1-C4H8]/[C4H10] ratio was reduced from approx.1.2 at 760 Torr (101 kPa) to approx.0.5 at 100 Torr (13.3 kPa) and approx.0.1 at pressures lower than about 5 Torr (approx.0.7 kPa). Electronic structure and RRKM calculations were used to simulate both unimolecular and bimolecular processes. The relative importance of C-C and C-H bond ruptures, cyclization, decyclization, and complex decompositions are discussed in terms of energetics and structural properties. The pressure dependence of the product yields were computed and dominant reaction paths in this chemically activated system were determined. Both modeling and experiment suggest that the observed pressure dependence of [1-C4H8]/[C4H10] is due to decomposition of the chemically activated combination adduct 1-C4H8* in which the weaker allylic C-C bond is broken: H2C=CHCH2CH3 yields C3H5 + CH3. This reaction occurs even at moderate pressures of approx.200 Torr (26 kPa) and becomes more significant at lower pressures. The additional products detected at lower pressures are formed from secondary radical-radical reactions involving allyl, methyl, ethyl, and vinyl radicals. The modeling studies have extended the predictions of product distributions to different temperatures (200-700 K) and a wider range of pressures (10(exp -3) - 10(exp 5) Torr). These calculations indicate that the high-pressure [1-C4H8]/[C4H10] yield ratio is 1.3 +/- 0.1.

High-level expression and efficient purification of bioactive swollenin in Aspergillus oryzae.

PubMed

Wang, Meihua; Cai, Jin; Huang, Lei; Lv, Zhengbin; Zhang, Yaozhou; Xu, Zhinan

2010-11-01

The bioactivity of swollenin is beneficial to cellulose decomposition by cellulase despite the lack of hydrolytic activity itself. In order to improve the productivity of swollenin, the effects of culture conditions on the expression level in recombinant Aspergillus oryzae were investigated systematically. With regard to the bioactivity of swollenin, glycerin and peanut meal were the optimal carbon or nitrogen source, respectively. The highest level production of swollenin (50 mg L(-1)) was attained after 88 h cultivation with the initial pH of 5.6 in the culture medium. Then the soluble swollenin was effectively purified from the cultural supernatant by ammonium sulfate precipitation and cationic exchange chromatography with recovery yield of 53.2%. The purified swollenin was fully bioactive due to its strong synergistic activity with cellulose.

The importance of measuring toothpaste abrasivity in both a quantitative and qualitative way.

PubMed

Johannsen, Gunnar; Tellefsen, Georg; Johannsen, Annsofi; Liljeborg, Anders

2013-01-01

To evaluate the relative abrasivity of different toothpastes and polishing pastes both qualitatively and quantitatively. Acrylic plates were exposed to brushing in a brushing machine with a toothpaste/water slurry for 1 and 6 h. Twelve different toothpastes were used and also four different polishing pastes. The results were evaluated using a profilometer after 1 and 6 h of brushing (corresponding to 2000 and 12 000 double strokes, respectively). A surface roughness value (Ra-value) and also a volume loss value were calculated from the profilometer measurements. These values were then correlated to each other. An unpaired t-test for the difference in the abrasion values between the toothpastes and the abrasion values over time was used. The polishing paste RDA® 170 yielded higher Ra-values than RDA 250®, both after 1 and 6 h of brushing (1.01 ± 0.22 and 8.99 ± 1.55 compared to 0.63 ± 0.26 and 7.83 ± 5.89, respectively) as well as volume loss values (3.71 ± 0.17 and 20.20 ± 2.41 compared to 2.15 ± 1.41 and 14.79 ± 11.76, respectively), thus poor correlations between the RDA and Ra and Volume loss values were shown. Among the toothpastes, Apotekets® showed the highest Ra value after 1 h of brushing and Pepsodent® whitening after 6 h of brushing. Pepsodent® whitening also showed the highest volume loss values, both after 1 and 6 h of brushing. This study emphasizes the importance of not only considering the RDA value, but also a roughness value, when describing the abrasivity of a toothpaste. Furthermore, it can be concluded that so called 'whitening' toothpastes do not necessarily have a higher abrasive effect than other toothpastes.

Deep blue exciplex organic light-emitting diodes with enhanced efficiency; P-type or E-type triplet conversion to singlet excitons?

PubMed

Jankus, Vygintas; Chiang, Chien-Jung; Dias, Fernando; Monkman, Andrew P

2013-03-13

Simple trilayer, deep blue, fluorescent exciplex organic light-emitting diodes (OLEDs) are reported. These OLEDs emit from an exciplex state formed between the highest occupied molecular orbital (HOMO) of N,N'-bis(1-naphthyl)N,N'-diphenyl-1,1'-biphenyl-4,4'-diamine (NPB) and lowest unoccupied molecular orbital (LUMO) of 1,3,5-tri(1-phenyl-1H-benzo[d]imidazol-2-yl)phenyl (TPBi) and the NPB singlet manifold, yielding 2.7% external quantum efficiency at 450 nm. It is shown that the majority of the delayed emission in electroluminescence arises from P-type triplet fusion at NPB sites not E-type reverse intersystem crossing because of the presence of the NPB triplet state acting as a deep trap. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Process Performances of 2 ns Pulsed Discharge Plasma

NASA Astrophysics Data System (ADS)

Matsumoto, Takao; Wang, Douyan; Namihira, Takao; Akiyama, Hidenori

2011-08-01

Pulsed discharge plasmas have been used to treat exhaust gases. Since pulse duration and the rise time of applied voltage to the discharge electrode has a strong influence on the energy efficiency of pollutant removal, the development of a short-pulse generator is of paramount importance for practical applications. In this work, it is demonstrated that the non thermal plasma produced by the 2 ns pulsed discharge has a higher energy efficiency than the 5 ns pulsed discharge plasma for NO removal and ozone generation. Typically, the NO removal efficiency was 1.0 mol kW-1 h-1 for 70% NO removal (initial NO concentration = 200 ppm, gas flow = 10 L/min). Meanwhile, the ozone yield was 500 g kW-1 h-1 for 20 g/m3 ozone concentration in the case of oxygen feeding. These energy efficiencies are the highest in the literature.

Molecular and functional properties of gelatin from the skin of unicorn leatherjacket as affected by extracting temperatures.

PubMed

Kaewruang, Phanngam; Benjakul, Soottawat; Prodpran, Thummanoon

2013-06-01

Gelatins extracted from the skin of unicorn leatherjacket at different temperatures (45, 55, 65 and 75°C) in the presence and the absence of soybean trypsin inhibitor (SBTI; 100 units/g pretreated skin) for 12h were characterised. In general, the addition of SBTI resulted in the lower yield, regardless of extraction temperature. Higher yield was obtained when higher extraction temperature was used (P<0.05). Gelatin from skin extracted at 75°C in the absence of SBTI showed the highest yield (10.66 ± 0.41%) (based on dry weight). The highest α-amino group content was observed in gelatin extracted at 55°C without SBTI incorporated. The band intensity of β-chain and α-chains increased as the extraction temperature increased, particularly above 55°C. Gelatin extracted at 65°C with and without SBTI incorporation exhibited the highest gel strength (178.00 ± 7.50 g and 170.47 ± 1.30 g, respectively). FTIR spectra indicated that a greater loss of molecular order of triple helix with a higher degradation was found in gelatin extracted at 55°C in the absence SBTI. Gelatin extracted at 65°C, either with or without SBTI, had the highest EAI and ESI with high foam expansion and stability. Thus, the extraction of gelatin from the skin of unicorn leatherjacket at temperature sufficiently high could render the gelatin with less degradation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Characterization of H2 photoproduction by marine green alga Tetraselmis subcordiformis integrated with an alkaline fuel cell.

PubMed

Guo, Zhen; Li, Ying; Guo, Haiyan

2016-03-01

To investigate the feasibility of coupling carbonyl cyanide m-chlorophenylhydrazone-regulated photohydrogen production by Tetraselmis subcordiformis in a photobioreactor to an alkaline fuel cell (AFC). H2 evolution kinetics in the AFC integrated process was characterized. The duration of H2 evolution was prolonged and its yield was improved about 1.5-fold (to 78 ± 5 ml l(-1)) compared with that of the process without AFC. Improved H2 yield was possibly caused by removal of H2 feedback inhibition by H2 consumption in situ. Decreases in the H2 production rate correlated with the gradual deactivation of PSII and hydrogenase activities. The H2 yield was closely associated with catabolism of starch and protein. A marine green algal CO2-supplemented culture integrated with in situ H2-consumption by an AFC system was developed as a viable protocol for the H2 production.

Measuring oxygen yields of a thermal conversion/elemental analyzer-isotope ratio mass spectrometer for organic and inorganic materials through injection of CO.

PubMed

Yin, Xijie; Chen, Zhigang

2014-12-01

The thermal conversion/elemental analyzer-isotope ratio mass spectrometer (TC/EA-IRMS) is widely used to measure the δ(18) O value of various substances. A premise for accurate δ(18) O measurement is that the oxygen in the sample can be converted into carbon monoxide (CO) quantitatively or at least proportionally. Therefore, a precise method to determine the oxygen yield of TC/EA-IRMS measurements is needed. Most studies have used the CO peak area obtained from a known amount of a solid reference material (for example, benzoic acid) to calibrate the oxygen yield of the sample. Although it was assumed that the oxygen yield of the solid reference material is 100%, no direct evidence has been provided. As CO is the analyte gas for δ(18) O measurement by IRMS, in this study, we use a six-port valve to inject CO gas into the TC/EA. The CO is carried to the IRMS by the He carrier gas and the CO peak area is measured by the IRMS. The CO peak area thus obtained from a known amount of the injected CO is used to calibrate the oxygen yield of the sample. The oxygen yields of commonly used organic and inorganic reference materials such as benzoic acid (C6 H5 COOH), silver phosphate (Ag3 PO4 ), calcium carbonate (CaCO3 ) and silicon dioxide (SiO2 ) are investigated at different reactor temperatures and sample sizes. We obtained excellent linear correlation between the peak area for the injected CO and its oxygen atom amount. C6 H5 COOH has the highest oxygen yield, followed by Ag3 PO4 , CaCO3 and SiO2 . The oxygen yields of TC/EA-IRMS are less than 100% for both organic and inorganic substances, but the yields are relatively stable at the specified reactor temperature and for a given quantity of sample. Copyright © 2014 John Wiley & Sons, Ltd.

Effect of fortification with various types of milk proteins on the rheological properties and permeability of nonfat set yogurt.

PubMed

Peng, Y; Serra, M; Horne, D S; Lucey, J A

2009-01-01

Yogurt base was prepared from reconstituted skim milk powder (SMP) with 2.5% protein and fortified with additional 1% protein (wt/wt) from 4 different milk protein sources: SMP, milk protein isolate (MPI), micellar casein (MC), and sodium caseinate (NaCN). Heat-treated yogurt mixes were fermented at 40 degrees C with a commercial yogurt culture until pH 4.6. During fermentation pH was monitored, and storage modulus (G') and loss tangent (LT) were measured using dynamic oscillatory rheology. Yield stress (sigma(yield)) and permeability of gels were analyzed at pH 4.6. Addition of NaCN significantly reduced buffering capacity of yogurt mix by apparently solubilizing part of the indigenous colloidal calcium phosphate (CCP) in reconstituted SMP. Use of different types of milk protein did not affect pH development except for MC, which had the slowest fermentation due to its very high buffering. NaCN-fortified yogurt had the highest G' and sigma(yield) values at pH 4.6, as well as maximum LT values. Partial removal of CCP by NaCN before fermentation may have increased rearrangements in yogurt gel. Soluble casein molecules in NaCN-fortified milks may have helped to increase G' and LT values of yogurt gels by increasing the number of cross-links between strands. Use of MC increased the CCP content but resulted in low G' and sigma(yield) at pH 4.6, high LT and high permeability. The G' value at pH 4.6 of yogurts increased in the order: SMP = MC < MPI < NaCN. Type of milk protein used to standardize the protein content had a significant impact on physical properties of yogurt. Practical Application: In yogurt processing, it is common to add additional milk solids to improve viscosity and textural attributes. There are many different types of milk protein powders that could potentially be used for fortification purposes. This study suggests that the type of milk protein used for fortification impacts yogurt properties and sodium caseinate gave the best textural results.

Anaerobic digestion of autoclaved and untreated food waste

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tampio, Elina, E-mail: elina.tampio@mtt.fi; Ervasti, Satu; Paavola, Teija

2014-02-15

Highlights: • Autoclaving decreased the formation of NH4-N and H{sub 2}S during food waste digestion. • Stable digestion was achieved with untreated and autoclaved FW at OLR 6 kg VS/m{sup 3}day. • Use of acclimated inoculum allowed very rapid increases in OLR. • Highest CH{sub 4} yields were observed at OLR 3 kg VS/m{sup 3}day with untreated FW. • Autoclaved FW produced highest CH{sub 4} yields during OLR 4 kgVS/m{sup 3}day. - Abstract: Anaerobic digestion of autoclaved (160 °C, 6.2 bar) and untreated source segregated food waste (FW) was compared over 473 days in semi-continuously fed mesophilic reactors with tracemore » elements supplementation, at organic loading rates (OLRs) of 2, 3, 4 and 6 kg volatile solids (VS)/m{sup 3} d. Methane yields at all OLR were 5–10% higher for untreated FW (maximum 0.483 ± 0.013 m{sup 3} CH{sub 4}/kg VS at 3 kg VS/m{sup 3} d) than autoclaved FW (maximum 0.439 ± 0.020 m{sup 3} CH{sub 4}/kg VS at 4 kg VS/m{sup 3} d). The residual methane potential of both digestates at all OLRs was less than 0.110 m{sup 3} CH{sub 4}/kg VS, indicating efficient methanation in all cases. Use of acclimated inoculum allowed very rapid increases in OLR. Reactors fed on autoclaved FW showed lower ammonium and hydrogen sulphide concentrations, probably due to reduced protein hydrolysis as a result of formation of Maillard compounds. In the current study this reduced biodegradability appears to outweigh any benefit due to thermal hydrolysis of ligno-cellulosic components.« less

Induction of Defense-Related Physiological and Antioxidant Enzyme Response against Powdery Mildew Disease in Okra (Abelmoschus esculentus L.) Plant by Using Chitosan and Potassium Salts.

PubMed

Soliman, Mona H; El-Mohamedy, Riad S R

2017-12-01

Foliar sprays of three plant resistance inducers, including chitosan (CH), potassium sorbate (PS) (C 6 H 7 kO 2 ), and potassium bicarbonates (PB) (KHCO 3 ), were used for resistance inducing against Erysiphe cichoracearum DC (powdery mildew) infecting okra plants. Experiments under green house and field conditions showed that, the powdery mildew disease severity was significantly reduced with all tested treatments of CH, PS, and PB in comparison with untreated control. CH at 0.5% and 0.75% (w/v) plus PS at 1.0% and 2.0% and/or PB at 2.0% or 3.0% recorded as the most effective treatments. Moreover, the highest values of vegetative studies and yield were observed with such treatments. CH and potassium salts treatments reflected many compounds of defense singles which leading to the activation power defense system in okra plant. The highest records of reduction in powdery mildew were accompanied with increasing in total phenolic, protein content and increased the activity of polyphenol oxidase, peroxidase, chitinase, and β-1,3-glucanase in okra plants. Meanwhile, single treatments of CH, PS, and PB at high concentration (0.75%, 2.0%, and/or 3.0%) caused considerable effects. Therefore, application of CH and potassium salts as natural and chemical inducers by foliar methods can be used to control of powdery mildew disease at early stages of growth and led to a maximum fruit yield in okra plants.

Transition Metal Phosphide Nanoparticles Supported on SBA-15 as Highly Selective Hydrodeoxygenation Catalysts for the Production of Advanced Biofuels.

PubMed

Yang, Yongxing; Ochoa-Hernández, Cristina; de la Peña O'Shea, Víctor A; Pizarro, Patricia; Coronado, Juan M; Serrano, David P

2015-09-01

A series of catalysts constituted by nanoparticles of transition metal (M = Fe, Co, Ni and Mo) phosphides (TMP) dispersed on SBA-15 were synthesized by reduction of the corresponding metal phosphate precursors previously impregnated on the mesostructured support. All the samples contained a metal-loading of 20 wt% and with an initial M/P mole ratio of 1, and they were characterized by X-ray diffraction (XRD), N2 sorption, H2-TPR and transmission electron microscopy (TEM). Metal phosphide nanocatalysts were tested in a high pressure continuous flow reactor for the hydrodeoxygenation (HDO) of a methyl ester blend containing methyl oleate (C17H33-COO-CH3) as main component (70%). This mixture constitutes a convenient surrogate of triglycerides present in vegetable oils, and following catalytic hydrotreating yields mainly n-alkanes. The results of the catalytic assays indicate that Ni2P/SBA-15 catalyst presents the highest ester conversion, whereas the transformation rate is about 20% lower for MoP/SBA-15. In contrast, catalysts based on Fe and Co phosphides show a rather limited activity. Hydrocarbon distribution in the liquid product suggests that both hydrodeoxygenation and decarboxylation/decarbonylation reactions occur simultaneously over the different catalysts, although MoP/SBA-15 possess a selectivity towards hydrodeoxygenation exceeding 90%. Accordingly, the catalyst based on MoP affords the highest yield of n-octadecane, which is the preferred product in terms of carbon atom economy. Subsequently, in order to conjugate the advantages of both Ni and Mo phosphides, a series of catalysts containing variable proportions of both metals were prepared. The obtained results reveal that the mixed phosphides catalysts present a catalytic behavior intermediate between those of the monometallic phosphides. Accordingly, only marginal enhancement of the yield of n-octadecane is obtained for the catalysts with a Mo/Ni ratio of 3. Nevertheless, owing to this high selectivity for hydrodeoxygenation MoP/SBA-15 appears as a very promising catalyst for the production of advanced biofuels.

Assessing relative abundance and reproductive success of shrubsteppe raptors

USGS Publications Warehouse

Lehman, Robert N.; Carpenter, L.B.; Steenhof, Karen; Kochert, Michael N.

1998-01-01

From 1991-1994, we quantified relative abundance and reproductive success of the Ferruginous Hawk (Buteo regalis), Northern Harrier (Circus cyaneus), Burrowing Owl (Speotytoc unicularia), and Short-eared Owl (Asio flammeus) on the shrubsteppe plateaus (benchlands) in and near the Snake River Birds of Prey National Conservation Area in southwestern Idaho. To assess relative abundance, we searched randomly selected plots using four sampling methods: point counts, line transects, and quadrats of two sizes. On a persampling-effort basis, transects were slightly more effective than point counts and quadrats for locating raptor nests (3.4 pairs detected/100 h of effort vs. 2.2-3.1 pairs). Random sampling using quadrats failed to detect a Short-eared Owl population increase from 1993 to 1994. To evaluate nesting success, we tried to determine reproductive outcome for all nesting attempts located during random, historical, and incidental nest searches. We compared nesting success estimates based on all nesting attempts, on attempts found during incubation, and the Mayfield model. Most pairs used to evaluate success were pairs found incidentally. Visits to historical nesting areas yielded the highest number of pairs per sampling effort (14.6/100 h), but reoccupancy rates for most species decreased through time. Estimates based on all attempts had the highest sample sizes but probably overestimated success for all species except the Ferruginous Hawk. Estimates of success based on nesting attempts found during incubation had the lowest sample sizes. All three methods yielded biased nesting snccess estimates for the Northern Harrier and Short-eared Owl. The estimate based on pairs found during incubation probably provided the least biased estimate for the Burrowing Owl. Assessments of nesting success were hindered by difficulties in confirming egg laying and nesting success for all species except the Ferruginous hawk.

Production of uridine 5'-monophosphate by Corynebacterium ammoniagenes ATCC 6872 using a statistically improved biocatalytic process.

PubMed

Wang, Xing; Wang, Xiuwen; Yin, Mengxin; Xiao, Zijun; Ma, Cuiqing; Lin, Zhixin; Wang, Peng George; Xu, Ping

2007-08-01

Attempts were made with success to develop a two-step biocatalytic process for uridine 5'-monophosphate (UMP) production from orotic acid by Corynebacterium ammoniagenes ATCC 6872: the strain was first cultivated in a high salt mineral medium, and then cells were harvested and used as the catalyst in the UMP production reaction. Effects of cultivation and reaction conditions on UMP production were investigated. The cells exhibited the highest biocatalytic ability when cultivated in a medium containing corn steep liquor at pH 7.0 for 15 h in the exponential phase of growth. To optimize the reaction, both "one-factor-at-a-time" method and statistical method were performed. By "one-factor-at-a-time" optimization, orotic acid, glucose, phosphate ion (equimolar KH(2)PO(4) and K(2)HPO(4)), MgCl(2), Triton X-100 were shown to be the optimum components for the biocatalytic reaction. Phosphate ion and C. ammoniagenes cell were furthermore demonstrated as the most important main effects on UMP production by Plackett-Burman design, indicating that 5-phosphoribosyl-1-pyrophosphate (PRPP) synthesis was the rate-limiting step for pyrimidine nucleotides production. Optimization by a central composition design (CCD) was then performed, and up to 32 mM (10.4 g l(-1)) UMP was accumulated in 24 h from 38.5 mM (6 g l(-1)) orotic acid. The yield was threefold higher than the original UMP yield before optimization.

Effects of temperature, pH and NaCl content on in vitro putrescine and cadaverine production through the growth of Serratia marcescens CCM 303.

PubMed

Bubelová, Zuzana; Buňka, František; Taťáková, Monika; Štajnochová, Kateřina; Purevdorj, Khatantuul; Buňková, Leona

2015-01-01

The aim of this study was to evaluate the combined effect of temperature (10, 20 and 37°C), pH (4, 5, 6, 7 and 8), and NaCl content (0, 1, 3, 4, 5 and 6% w/v) on the growth and putrescine and cadaverine production of Serratia marcescens CCM 303 under model conditions. The decarboxylase activity of S. marcescens was monitored in broth after cultivation. The cultivation medium was enriched with selected amino acids (ornithine, arginine and lysine; 0.2% w/v each) serving as precursors of biogenic amines. Levels of putrescine and cadaverine in broth were analysed by high-performance liquid chromatography after pre-column derivatisation with o-phthalaldehyde reagent. S. marcescens produced higher amounts of putrescine (up to 2096.8 mg L(-1)) compared to cadaverine content (up to 343.3 mg L(-1)) in all cultivation media. The highest putrescine and cadaverine concentrations were reached during cultivation at 10-20°C, pH 5-7 and NaCl content 1-3% w/v. On the other hand, the highest BAs production of individual cell (recalculated based on a cell; so called "yield factor") was observed at 10°C, pH 4 and salt concentration 3-5% w/v as a response to environmental stress.

Classical trajectory studies of gas phase reaction dynamics and kinetics using ab initio potential energy surfaces

NASA Technical Reports Server (NTRS)

Jaffe, Richard L.; Pattengill, Merle D.; Schwenke, David W.

1989-01-01

Strategies for constructing global potential energy surfaces from a limited number of accurate ab initio electronic energy calculations are discussed. Generally, these data are concentrated in small regions of configuration space (e.g., in the vicinity of saddle points and energy minima) and difficulties arise in generating a potential function that is globally well-behaved. Efficient computer codes for carrying out classical trajectory calculations on vector and parallel processors are also described. Illustrations are given from recent work on the following chemical systems: Ca + HF yields CaF + H, H + H + H2 yields H2 + H2, N + O2 yields NO + O and O + N2 yields NO + N. The dynamics and kinetics of metathesis, dissociation, recombination, energy transfer and complex formation processes will be discussed.

Optimized formation of detergent micelles of beta-carotene and retinal production using recombinant human beta,beta-carotene 15,15'-monooxygenase.

PubMed

Kim, Nam-Hee; Kim, Yeong-Su; Kim, Hye-Jung; Oh, Deok-Kun

2008-01-01

The formation of beta-carotene detergent micelles and their conversion into retinal by recombinant human beta,beta-carotene 15,15'-monooxygenase was optimized under aqueous conditions. Toluene was the most hydrophobic among the organic solvents tested; thus, it was used to dissolve beta-carotene, which is a hydrophobic compound. Tween 80 was selected as the detergent because it supported the highest level of retinal production among all of the detergents tested. The maximum production of retinal was achieved in detergent micelles containing 200 mg/L of beta-carotene and 2.4% (w/v) Tween 80. Under these conditions, the recombinant enzyme produced 97 mg/L of retinal after 16 h with a conversion yield of 48.5% (w/w). The amount of retinal produced, which is the highest ever reported, is a result of the ability of our system to dissolve large amounts of beta-carotene.

Synthesis of CuInSe2 nanocrystals using a continuous hot-injection microreactor

NASA Astrophysics Data System (ADS)

Jin, Hyung Dae; Chang, Chih-Hung

2012-10-01

A very rapid and simple synthesis of CuInSe2 nanocrystals (NCs) was successfully performed using a continuous hot-injection microreactor with a high throughput per reactor volume. It was found that copper-rich CuInSe2 with a sphalerite structure was formed initially followed by the formation of more ordered CuInSe2 at longer reaction times along with the formation of Cu2Se and In2Se3. Binary syntheses were performed and the results show a much faster formation rate of Cu2Se than In2Se3. The rate limiting step in the formation of CuInSe2 is forming the In2Se3 intermediate. Rapid synthesis of stoichiometric CuInSe2 NCs using a continuous-flow microreactor was accomplished by properly adjusting the Cu/In precursor ratio. Tuning the ratio of coordinating solvents can cause size differences from 2.6 to 4.1 nm, bandgaps from 1.1 to 1.3 eV, and different production yields of NCs. The highest production yield as determined by weight was achieved up to 660 mg/h using a microreactor with a small volume of 3.2 cm3.

Development of parmesan cheese production from local cow milk

NASA Astrophysics Data System (ADS)

Aliwarga, Lienda; Christianti, Elisabeth Novi; Lazarus, Chrisella

2017-05-01

Parmesan cheese is one of the dairy products which is used in various foods, such as pasta, bakery product, and pizza. It has a hard texture due to aging process for at least two years. Long aging period inhibited the production of parmesan cheese while consumer demands were increasing gradually. This research was conducted to figure out the effect of starter culture and rennet dose to the production of parmesan cheese. This research consists of (1) pasteurization of 1,500 ml milk at 73°C; and (2) main cheese making process that comprised of fermentation process and the addition of rennet. In latter stage, milk was converted into curd. Variations were made for the dose of bacteria culture and rennet. Both variables correlated to the fermentation time and characteristics of the produced cheese. The analysis of the produced cheese during testing stage included measured protein and cheese yield, whey pH, water activity, and moisture content. Moreover, an organoleptic test was done in a qualitative manner. The results showed that the dose of bacteria culture has a significant effect to the fermentation time, protein yield, and cheese yield. Meanwhile, rennet dose significantly affected cheese yield, pH of whey, and water activity. The highest protein yield (93.1%) was obtained at 0.6 ml of culture and 0.5 ml of rennet while the maximum cheese yield (6.81%) was achieved at 0.4 ml of culture and 0.1 ml of rennet. The water activity of produced cheeses was lower compared to the water activity of common parmesan cheese (ca. 0.6). For the organoleptic test, 0.4 ml of bacterial culture and 0.5 ml of rennet produced the most preferred cheese flavor compared to other variations.

High-titer and productivity of l-(+)-lactic acid using exponential fed-batch fermentation with Bacillus coagulans arr4, a new thermotolerant bacterial strain.

PubMed

Coelho, Luciana Fontes; Beitel, Susan Michelz; Sass, Daiane Cristina; Neto, Paulo Marcelo Avila; Contiero, Jonas

2018-04-01

Bacillus coagulans arr4 is a thermotolerant microorganism with great biotechnological potential for l-(+)-lactic acid production from granulated sugar and yeast extract. The highest l-(+)-lactic acid production was obtained with Ca(OH) 2 . The maximum production of l-(+)-lactic acid (206.81 g/L) was observed in exponential feeding using granulated sugar solution (900 g/L) and yeast extract (1%) at 50 °C, pH 6.5, and initial granulated sugar concentration of 100 g/L at 39 h. 5.3 g/L h productivity and 97% yield were observed, and no sugar remained. Comparing the simple batch with exponential fed-batch fermentation, the l(+) lactic acid production was improved in 133.22% and dry cell weight was improved in 83.29%, using granulated sugar and yeast extract. This study presents the highest productivity of lactic acid ever observed in the literature, on the fermentation of thermotolerant Bacillus sp. as well as an innovative and high-efficiency purification technology, using low-cost substances as Celite and charcoal. The recovery of lactic acid was 86%, with 100% protein removal, and the fermentation medium (brown color) became a colorless solution.

FeCl3-catalyzed ethanol pretreatment of sugarcane bagasse boosts sugar yields with low enzyme loadings and short hydrolysis time.

PubMed

Zhang, Hongdan; Zhang, Shuaishuai; Yuan, Hongyou; Lyu, Gaojin; Xie, Jun

2018-02-01

An organosolv pretreatment system consisting of 60% ethanol and 0.025 mol·L -1 FeCl 3 under various temperatures was developed in this study. During the pretreatment, the highest xylose yield was 11.4 g/100 g raw material, representing 49.8% of xylose in sugarcane bagasse. Structural features of raw material and pretreated substrates were characterized to better understand how hemicellulose removal and delignification affected subsequent enzymatic hydrolysis. The 160 °C pretreated solid presented a remarkable glucose yield of 93.8% for 72 h. Furthermore, the influence of different additives on the enzymatic hydrolysis of pretreated solid was investigated. The results indicated that the addition of Tween 80 shortened hydrolysis time to 6 h and allowed a 50% reduction of enzyme loading to achieve the same level of glucose yield. This work suggested that FeCl 3 -catalyzed organosolv pretreatment could improve the enzymatic hydrolysis significantly and reduce the hydrolysis time and enzyme dosage with the addition of Tween 80. Copyright © 2017 Elsevier Ltd. All rights reserved.

Optimization of Ultrasound Assisted Extraction of Functional Ingredients from Stevia Rebaudiana Bertoni Leaves

NASA Astrophysics Data System (ADS)

Šic Žlabur, Jana; Voća, Sandra; Dobričević, Nadica; Brnčić, Mladen; Dujmić, Filip; Rimac Brnčić, Suzana

2015-04-01

The aim of the present study was to reveal an effective extraction procedure for maximization of the yield of steviol glycosides and total phenolic compounds as well as antioxidant activity in stevia extracts. Ultrasound assisted extraction was compared with conventional solvent extraction. The examined solvents were water (100°C/24 h) and 70% ethanol (at 70°C for 30 min). Qualitative and quantitative analyses of steviol glycosides in the extracts obtained were performed using high performance liquid chromatography. Total phenolic compounds, flavonoids, and radical scavenging capacity by 2, 2-azino-di-3-ethylbenzothialozine- sulphonic acid) assay were also determined. The highest content of steviol glycosides, total phenolic compounds, and flavonoids in stevia extracts were obtained when ultrasound assisted extraction was used. The antioxidant activity of the extracts was correlated with the total amount of phenolic compounds. The results indicated that the examined sonication parameters represented as the probe diameter (7 and 22 mm) and treatment time (2, 4, 6, 8, and 10 min) significantly contributed to the yield of steviol glycosides, total phenolic compounds, and flavonoids. The optimum conditions for the maximum yield of steviol glycosides, total phenolic compounds, and flavonoids were as follows: extraction time 10 min, probe diameter 22 mm, and temperature 81.2°C.

Transesterification of edible, non-edible and used cooking oils for biodiesel production using calcined layered double hydroxides as reusable base catalysts.

PubMed

Sankaranarayanan, Sivashunmugam; Antonyraj, Churchil A; Kannan, S

2012-04-01

Fatty acid methyl esters (FAME) were produced from edible, non-edible and used cooking oils with different fatty acid contents by transesterification with methanol using calcined layered double hydroxides (LDHs) as solid base catalysts. Among the catalysts, calcined CaAl2-LDH (hydrocalumite) showed the highest activity with >90% yield of FAME using low methanol:oil molar ratio (<6:1) at 65 °C in 5 h. The activity of the catalyst was attributed to its high basicity as supported by Hammett studies and CO(2)-TPD measurements. The catalyst was successfully reused in up to four cycles. Some of the properties such as density, viscosity, neutralization number and glycerol content of the obtained biodiesel matched well with the standard DIN values. It is concluded that a scalable heterogeneously catalyzed process for production of biodiesel in high yields from a wide variety of triglyceride oils including used oils is possible using optimized conditions. Copyright © 2012 Elsevier Ltd. All rights reserved.

Influence of body condition score on carcass characteristics and subprimal yield from cull beef cows.

PubMed

Apple, J K; Davis, J C; Stephenson, J; Hankins, J E; Davis, J R; Beaty, S L

1999-10-01

Mature beef cows (n = 83) were slaughtered to measure the influence of body condition score (BCS) on carcass characteristics and subprimal yields. All cows were weighed and assigned BCS, based on a 9-point scale, 24 h before slaughter. Cows were slaughtered, and, after a 48-h chilling period, quality and yield grade data were collected on the left side of each carcass. The right side was quartered, fabricated into primal cuts, and weighed. Each primal cut was further processed into boneless subprimal cuts, minor cuts, lean trim, fat, and bone. Cuts were progressively trimmed to 6.4 and 0 mm of external and visible seam fat. Weights were recorded at all stages of fabrication, and subprimal yields were calculated as a percentage of the chilled carcass weight. Live weight, carcass weight, dressing percentage, fat thickness, longissimus muscle area, muscle:bone ratio, and numerical yield grade increased linearly (P = .0001) and predicted cutability and actual muscle-to-fat ratio decreased linearly (P = .0001) as BCS increased from 2 to 8. Carcasses from BCS-8 cows had the most (P<.05) marbling. The percentage of carcasses grading U.S. Utility, or higher, was 16.7, 20.0, 63.6, 43.3, 73.3, 100.0, and 100.0% for cows assigned a BCS of 2, 3, 4, 5, 6, 7, and 8, respectively. At 6.4 mm of fat trim, carcasses from BCS-5 cows had higher (P<.05) shoulder clod yields than carcasses from cows having a BCS of 6, 7, and 8. Carcasses of BCS-2 cows had lower (P<.05) strip loin yields than carcasses from BCS-3, 4, 5, 6, and 7 cows. Top sirloin butt yields were higher (P<.05) for carcasses of BCS-2, 3, 4, and 5 cows than those of BCS-6, 7, or 8 cows. Carcasses from BCS-7 and 8 cows had lower (P<.05) tenderloin and inside round yields than carcasses of BCS-5, or less, cows. At both fat-trim levels, carcasses from BCS-5 cows had higher (P<.05) eye of round yields than cows assigned BCS of 2, 7, or 8. When subprimal cuts were trimmed to 6.4 mm of visible fat, carcasses from BCS-5 cows had higher (P<.05) total lean product yields than cows assigned a BCS of 2, 4, 7, and 8. Regardless of fat trim, total fat yields increased (P = .0001) and total bone yields decreased (P = .0001) linearly as BCS increased from 2 to 8. Although carcasses from BCS-5 and 6 cows had the highest yields of lean product, cattle producers and packers may benefit most by marketing and(or) purchasing BCS-6 cows because a higher percentage of their carcasses had quality characteristics deemed desirable for fabrication into boneless subprimal cuts.

Water Ice Radiolytic O2, H2, and H2O2 Yields for Any Projectile Species, Energy, or Temperature: A Model for Icy Astrophysical Bodies

NASA Astrophysics Data System (ADS)

Teolis, B. D.; Plainaki, C.; Cassidy, T. A.; Raut, U.

2017-10-01

O2, H2, and H2O2 radiolysis from water ice is pervasive on icy astrophysical bodies, but the lack of a self-consistent, quantitative model of the yields of these water products versus irradiation projectile species and energy has been an obstacle to estimating the radiolytic oxidant sources to the surfaces and exospheres of these objects. A major challenge is the wide variation of O2 radiolysis yields between laboratory experiments, ranging over 4 orders of magnitude from 5 × 10-7 to 5 × 10-3 molecules/eV for different particles and energies. We revisit decades of laboratory data to solve this long-standing puzzle, finding an inverse projectile range dependence in the O2 yields, due to preferential O2 formation from an 30 Å thick oxygenated surface layer. Highly penetrating projectile ions and electrons with ranges ≳30 Å are therefore less efficient at producing O2 than slow/heavy ions and low-energy electrons (≲ 400 eV) which deposit most energy near the surface. Unlike O2, the H2O2 yields from penetrating projectiles fall within a comparatively narrow range of (0.1-6) × 10-3 molecules/eV and do not depend on range, suggesting that H2O2 forms deep in the ice uniformly along the projectile track, e.g., by reactions of OH radicals. We develop an analytical model for O2, H2, and H2O2 yields from pure water ice for electrons and singly charged ions of any mass and energy and apply the model to estimate possible O2 source rates on several icy satellites. The yields are upper limits for icy bodies on which surface impurities may be present.

Polyhydroxyalkanoate recovery and effect of in situ extracellular polymeric substances removal from aerobic granules.

PubMed

Gobi, K; Vadivelu, V M

2015-01-01

Polyhydroxyalkanoate (PHA) recovery from aerobic granules was investigated using four cell digestion agents, namely, sodium hypochlorite, sodium hydroxide, acetone and sodium chloride. Simultaneously, the removal of extracellular polymeric substances (EPS) and its effect on PHA yield were investigated. The highest PHA recovery yield was obtained using sodium hypochlorite, accounting for 89% cell dry weight (CDW). The highest PHA was recovered after the sodium hypochlorite completely removed the EPS from the aerobic granules. The average molecular weight (Mw) of the PHA recovered using sodium hypochlorite was 5.31 × 10(5)g/mol with only 1.8% molecular weight degradation. The energy and duration analysis for PHA recovery revealed that the sodium hypochlorite method required the least amount of energy and time at 0.0561 MJ/g PHA and 26 h, respectively. The PHA that was recovered was a P3(HB-co-HV) co-polymer. Copyright © 2015 Elsevier Ltd. All rights reserved.

Application of bacteriophages specific to hydrogen sulfide-producing bacteria in raw poultry by-products.

PubMed

Gong, Chao; Liu, Xiaohua; Jiang, Xiuping

2014-03-01

Hydrogen sulfide-producing bacteria (SPB) can spoil raw animal materials and release harmful hydrogen sulfide (H2S) gas. The objective of this study was to apply a SPB-specific bacteriophage cocktail to control H2S production by SPB in different raw poultry by-products in the laboratory (20, 30, and 37°C) and greenhouse (average temperature 29 to 31°C, humidity 34.8 to 59.8%, and light intensity 604.8 Wm(2)) by simulating transportation and a rendering facility. The amount of H2S production was determined using either test strips impregnated with lead acetate or a H2S monitor. In the laboratory, phage treatment applied to fresh chicken meat inoculated with SPB, spoiled chicken meat, chicken guts, and chicken feathers reduced H2S production by approximately 25 to 69% at temperatures from 20 to 37°C. In the greenhouse, phage treatment achieved approximately a 30 to 85% reduction of H2S yield in chicken offal and feathers. Among all phage treatments, multiplicity of infection (MOI) of 100 exhibited the highest inhibitory activities against SPB on H2S production. Several factors such as initial SPB level, temperature, and MOI affect lytic activities of bacteriophages. Our study demonstrated that the phage cocktail is effective to reduce the production of H2S by SPB significantly in raw animal materials. This biological control method can control SPB in raw poultry by-products at ambient temperatures, leading to a safer working environment and high quality product with less nutrient degradation for the rendering industry.

Molecular Identification of a Newly Isolated Bacillus subtilis BI19 and Optimization of Production Conditions for Enhanced Production of Extracellular Amylase

PubMed Central

Dash, Biplab Kumar; Rahman, M. Mizanur; Sarker, Palash Kumar

2015-01-01

A study was carried out with a newly isolated bacterial strain yielding extracellular amylase. The phylogenetic tree constructed on the basis of 16S rDNA gene sequences revealed this strain as clustered with the closest members of Bacillus sp. and identified as Bacillus subtilis BI19. The effect of various fermentation conditions on amylase production through shake-flask culture was investigated. Rice flour (1.25%) as a cheap natural carbon source was found to induce amylase production mostly. A combination of peptone and tryptone as organic and ammonium sulfate as inorganic nitrogen sources gave highest yield. Maximum production was obtained after 24 h of incubation at 37°C with an initial medium pH 8.0. Addition of surfactants like Tween 80 (0.25 g/L) and sodium lauryl sulfate (0.2 g/L) resulted in 28% and 15% increase in enzyme production, respectively. Amylase production was 3.06 times higher when optimized production conditions were used. Optimum reaction temperature and pH for crude amylase activity were 50°C and 6.0, respectively. The crude enzyme showed activity and stability over a fair range of temperature and pH. These results suggest that B. subtilis BI19 could be exploited for production of amylase at relatively low cost and time. PMID:26180814

Integration of whole-cell reaction and product isolation: Highly hydrophobic solvents promote in situ substrate supply and simplify extractive product isolation.

PubMed

Leis, Dorothea; Lauß, Bernhard; Macher-Ambrosch, Robert; Pfennig, Andreas; Nidetzky, Bernd; Kratzer, Regina

2017-09-10

Product isolation from aqueous-organic reaction mixtures that contain high concentrations of whole cells constitutes a challenging task in bioprocessing. Stirring of the biphasic reaction media leads to the formation of solvent droplets coated by cells and other surface active components and an emulsion forms. We used an early focus on phase separation to simplify a whole-cell bioreduction. Octanol, heptanol, hexanol, hexane and dipropylether were tested as co-solvents in the E. coli catalyzed reduction of o-chloroacetophenone. All solvents showed very similar performance in bioreductions and highest yields were obtained with low organic-to-aqueous phase ratios. Reaction mixtures were directly investigated for organic-phase recovery. Phase separation was optimized in small-scale settling experiments and confirmed by the isolation of 20.4g (S)-1-(2-chlorophenyl)ethanol from a 0.5L batch reduction containing 40g CDW /L whole-cell catalyst. Solvent consumption during product isolation could be halved by the simple addition of sodium hydroxide prior to product extraction. Basification to pH 13.5 and three extraction steps with a total of 1.2v/v hexane led to an isolated yield of 87% (97% reduction yield). A general emulsion destabilizing effect under harsh conditions, as extreme pH values and presence of toxic reactants, was observed. Copyright © 2016 The Authors. Published by Elsevier B.V. All rights reserved.

[Effects of different colored plastic film mulching and planting density on dry matter accumulation and yield of spring maize.

PubMed

Zhang, Lin Lin; Sun, Shi Jun; Chen, Zhi Jun; Jiang, Hao; Zhang, Xu Dong; Chi, Dao Cai

2018-01-01

In order to investigate the effect of different colored plastic film mulching and planting density on spring maize dry matter accumulation and yield in the rain-fed area of the Northeast China, a complete combination field experiment which was comprised by three types of mulching (non-mulching, transparent plastic film mulching and black plastic film mulching) and five densities (60000, 67500, 75000, 82500 and 90000 plants·hm -2 ), was conducted to analyze the water and heat effect, dry matter accumulation and yield of spring maize (Liangyu 99). The results showed that, compared with the other mulching treatments, the black plastic film mulching treatment significantly increased the maize dry matter accumulation and maize biomass by 3.2%-8.2%. In mature stage, the biomass increased firstly and then decreased with the increasing plant density. When planting density was 82500 plants·hm -2 , the biomass was the highest, which was 5.2%-28.3% higher than that of other plant density treatments. The mean soil temperature in prophase of transparent plastic film mulching treatment was 0.4-2.7 ℃ higher than that of other treatments, which accelerated the maize growth process and augmented the dry matter transportation amount (T), dry matter transportation efficiency (TE) and contribution rate of dry matter transportation to the grain yield (TC) of maize stalk and leaf. The T, TE, TC of leaf and leaf-stalk under 60000 plants·hm -2 treatment were the highest. The highest T, TE, TC of stalk were observed under 75000 plants·hm -2 treatment. In heading period, the water consumption and daily water consumption intensity of maize under the treatment of black film mulching were the largest, which were 9.4%-10.6% and 10.6%-24.5% higher than that of other mulching treatments, respectively. The highest water consumption and daily water consumption intensity were both obtained under 90000 plants·hm -2 treatment, which increased by 6.8%-15.7% and 7.0%-20.0% compared with other plant density treatments. The combination of black film mulching and density of 82500 plants·hm -2 significantly improved the water use efficiency of maize, which increased by 4.6%-40.9% compared with other treatments. In addition, it increased yield by 3.0%-39.7% compared with other treatments. At heading stage, the correlation between the dry matter amount of stalk and leaf and the yield and yield components was the biggest. Decreasing 1 kg·hm -2 dry matter amount of stalk and leaf would decrease the population yield by almost 0.79 kg·hm -2 . Decreasing 10% dry matter amount of stalk and leaf would decrease the yield by almost 10%. Based on increasing plant density, black film mulching was beneficial for increasing the dry matter accumulation and improving grain yield and water use efficiency of spring maize.

Kinetic and Mechanistic Aspects of the Reactions of Iodide and Hypoiodous Acid with Permanganate: Oxidation and Disproportionation.

PubMed

Zhao, Xiaodan; Salhi, Elisabeth; Liu, Huiling; Ma, Jun; von Gunten, Urs

2016-04-19

Oxidation kinetics of iodide and HOI/OI(-) by permanganate were studied in the pH range of 5.0-10.0. Iodide oxidation and iodate formation were faster at lower pH. The apparent second-order rate constants (k(obs)) for iodide oxidation by permanganate decrease with increasing pH from 29 M(-1) s(-1) at pH 5.0 and 6.9 M(-1) s(-1) at pH 7.0 to 2.7 M(-1) s(-1) at pH 10.0. k(obs) for HOI abatement are 56 M(-1) s(-1) at pH 5.0, 2.5 M(-1) s(-1) at pH 7.0, and 173 M(-1) s(-1) at pH 10.0. Iodate yields over HOI abatement decrease from 98% at pH 6.0 to 33% for pH ≥ 9.5, demonstrating that HOI disproportionation dominates HOI transformation by permanganate at pH ≥ 8.0. MnO2 formed as a product from permanganate reduction, oxidizes HOI to iodate for pH < 8.0, and promotes HOI disproportionation for pH ≥ 8.0. The rate of HOI oxidation or disproportionation induced by MnO2 is much lower than for permanganate. During treatment of iodide-containing waters, the potential for iodinated disinfection byproducts (I-DBPs) formation is highest at pH 7.0-8.0 due to the long lifetime of HOI. For pH < 6.0, HOI/I2 is quickly oxidized by permanganate to iodate, whereas for pH ≥ 8.0, HOI/OI(-) undergoes a fast permanganate-mediated disproportionation.

Catalytic properties of a CoMo/Al[sub 2]O[sub 3] catalyst presulfided with alkyl polysulfides: Comparison with conventional sulfiding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gestel, J. van; Leglise, J.; Duchet, J.C.

1994-02-01

A CoMo/Al[sub 2]O[sub 3] hydrotreating catalyst has been sulfided in different ways: (i) by conventional in situ sulfiding in a high-pressure reactor with a H[sub 2]S/H[sub 2] or dimethyldisulfide (DMDS)/H[sub 2] mixture at 350[degrees]C and 4 MPa; or (ii) by a preliminary presulfidation with di-tert-nonyl or di-tert-dodecyl pentasulfides followed by one of the above conventional in situ sulfidations. The presulfidation was performed in two steps: impregnation of the oxidic catalyst with the polysulfide and then thermal treatment under flowing nitrogen at 130[degrees]C. The catalysts were evaluated for their catalytic properties at 280-350[degrees]C and 4 MPa for the simultaneous hydrodesulfurization ofmore » thiophene and hydrogenation of cyclohexene. Compared to H[sub 2]S/H[sub 2], in situ DMDS/H[sub 2] sulfiding of the CoMo/Al[sub 2]O[sub 3] catalyst enhanced the C-S hydrogenolysis at 280[degrees]C but not the hydrogenation; however, the apparent activation energy for hydrogenation was markedly increased. The presulfidation with the polysulfides following by H[sub 2]S/H[sub 2] sulfidation yielded improved activities at 280[degrees]C for both hydrogenation and C-S bond breakage and did not influence the apparent activation energies. The highest activities were obtained by combining presulfiding and DMDS/H[sub 2] sulfidation. These results are discussed in terms of the genesis of the supported sulfide phase with various sulfur species. 40 refs., 2 figs., 2 tabs.« less

Simultaneous removal of NO and SO2 using vacuum ultraviolet light (VUV)/heat/peroxymonosulfate (PMS).

PubMed

Liu, Yangxian; Wang, Yan; Wang, Qian; Pan, Jianfeng; Zhang, Jun

2018-01-01

Simultaneous removal process of SO 2 and NO from flue gas using vacuum ultraviolet light (VUV)/heat/peroxymonosulfate (PMS) in a VUV spraying reactor was proposed. The key influencing factors, active species, reaction products and mechanism of SO 2 and NO simultaneous removal were investigated. The results show that vacuum ultraviolet light (185 nm) achieves the highest NO removal efficiency and yield of and under the same test conditions. NO removal is enhanced at higher PMS concentration, light intensity and oxygen concentration, and is inhibited at higher NO concentration, SO 2 concentration and solution pH. Solution temperature has a double impact on NO removal. CO 2 concentration has no obvious effect on NO removal. and produced from VUV-activation of PMS play a leading role in NO removal. O 3 and ·O produced from VUV-activation of O 2 also play an important role in NO removal. SO 2 achieves complete removal under all experimental conditions due to its very high solubility in water and good reactivity. The highest simultaneous removal efficiency of SO 2 and NO reaches 100% and 91.3%, respectively. Copyright © 2017 Elsevier Ltd. All rights reserved.

Microbial and nutritional regulation of high-solids anaerobic mono-digestion of fruit and vegetable wastes.

PubMed

Mu, Hui; Li, Yan; Zhao, Yuxiao; Zhang, Xiaodong; Hua, Dongliang; Xu, Haipeng; Jin, Fuqiang

2018-02-01

The anaerobic digestion of single fruit and vegetable wastes (FVW) can be easily interrupted by rapid acidogenesis and inhibition of methanogen, and the digestion system tends to be particularly unstable at high solid content. In this study, the anaerobic digestion of FVW in batch experiments under mesophilic condition at a high solid concentration of 10% was successfully conducted to overcome the acidogenesis problem through several modifications. Firstly, compared with the conventional anaerobic sludge (CAS), the acclimated anaerobic granular sludge (AGS) was found to be a better inoculum due to its higher Archaea abundance. Secondly, waste activated sludge (WAS) was chosen to co-digest with FVW, because WAS had abundant proteins that could generate intermediate ammonium. The ammonium could neutralize the accumulated volatile fatty acids (VFAs) and prevent the pH value of the digestion system from rapidly decreasing. Co-digestion of FVW and WAS with TS ratio of 60:40 gave the highest biogas yield of 562 mL/g-VS and the highest methane yield of 362 mL/g-VS. Key parameters in the digestion process, including VFAs concentration, pH, enzyme activity, and microbial activity, were also examined.

Composted oyster shell as lime fertilizer is more effective than fresh oyster shell.

PubMed

Lee, Young Han; Islam, Shah Md Asraful; Hong, Sun Joo; Cho, Kye Man; Math, Renukaradhya K; Heo, Jae Young; Kim, Hoon; Yun, Han Dae

2010-01-01

Physio-chemical changes in oyster shell were examined, and fresh and composted oyster shell meals were compared as lime fertilizers in soybean cultivation. Structural changes in oyster shell were observed by AFM and FE-SEM. We found that grains of the oyster shell surface became smoother and smaller over time. FT-IR analysis indicated the degradation of a chitin-like compound of oyster shell. In chemical analysis, pH (12.3+/-0.24), electrical conductivity (4.1+/-0.24 dS m(-1)), and alkaline powder (53.3+/-1.12%) were highest in commercial lime. Besides, pH was higher in composted oyster shell meal (9.9+/-0.53) than in fresh oyster shell meal (8.4+/-0.32). The highest organic matter (1.1+/-0.08%), NaCl (0.54+/-0.03%), and moisture (15.1+/-1.95%) contents were found in fresh oyster shell meal. A significant higher yield of soybean (1.33 t ha(-1)) was obtained by applying composted oyster shell meal (a 21% higher yield than with fresh oyster shell meal). Thus composting of oyster shell increases the utility of oyster shell as a liming material for crop cultivation.

Reducing the photo-bleaching effect of a new europium complex embedded in styrene butadiene copolymer

NASA Astrophysics Data System (ADS)

Jiménez, G. Lesly; Reyes-Rodríguez, J. L.; Padilla, Isela; Alarcón-Flores, G.; Falcony, C.

2018-02-01

A highly luminescent europium complex obtained with two different ligands, succinimide (SI) and 2-thenoyltrifluoroacetone (TTA) , was synthetized with different TTA concentrations. The photoluminescence (PL) emission from these materials corresponds to the characteristic inter-electronic energy level transitions of the Eu3+ ions. However, the excitation spectrum is strongly dependent on the presence of TTA, having an optimum response when 0.75 mmol of this compound is added to the EuL3(H2O)3 complex. The quantum yield obtained by these powders were around 72 % ± 1.7 % indicating an optimum sensitization of these complex. The EuL3 TTA complex with the best PL properties was embedded in a styrene butadiene copolymer (SBC) film, produced by the drop casting method, obtaining similar PL behavior at different concentrations, the highest intensity was observed at 1.2% (w/v) of EuL3 TTA complex and the quantum yield of these composite films was 60.5 % ± 2 % . These films were exposed to continuous UV irradiation and after 141 h no photo-bleaching effect was observed in contrast with the EuL3 TTA complex that exhibited a noticeable photoluminescence intensity degradation at much shorter exposure times. Both the Eu-complexes and the composite films were characterized by FT-IR, XRD, SEM and fluorescence spectroscopy.

A flash photolysis-resonance fluorescence study of the formation of O(D-1) in the photolysis of water and reaction of O(D-1) with H2, Ar and He

NASA Technical Reports Server (NTRS)

Stief, L. J.; Payne, W. A.; Klemm, R. B.

1974-01-01

The relative importance of two primary processes in the photolyis of water: (1) H2O + h (nu) yields H + OH, and (2) H2O + h (nu) yields H2 + OD-1 were determined in a direct manner by time resolved detection (via resonance fluorescence) of H and O formed in processes 1 and 2 respectively. The initially formed OD-1 was deactivated to ground state OP-3 prior to detection via resonance fluorescence. The relative quantum yields for processes 1 and 2 are 0.89 and 0.11 for the wavelength interval 105 to 145nm and = to or greater than 0.99, and = to or less than 0.01 for the wavelength interval 145 to 185nm. Rate constants at 300 K for the reactions OD-1 + H2, + Ar, and + He are presented.

Comparison of macrocyclic and acyclic chelators for gallium-68 radiolabelling.

PubMed

Tsionou, Maria Iris; Knapp, Caroline E; Foley, Calum A; Munteanu, Catherine R; Cakebread, Andrew; Imberti, Cinzia; Eykyn, Thomas R; Young, Jennifer D; Paterson, Brett M; Blower, Philip J; Ma, Michelle T

2017-10-24

Gallium-68 ( 68 Ga) is a positron-emitting isotope used for clinical PET imaging of peptide receptor expression. 68 Ga radiopharmaceuticals used in molecular PET imaging consist of disease-targeting biomolecules tethered to chelators that complex 68 Ga 3+ . Ideally, the chelator will rapidly, quantitatively and stably coordinate 68 Ga 3+ at room temperature, near neutral pH and low chelator concentration, allowing for simple routine radiopharmaceutical formulation. Identification of chelators that fulfil these requirements will facilitate development of kit-based 68 Ga radiopharmaceuticals. Herein the reaction of a range of widely used macrocyclic and acyclic chelators with 68 Ga 3+ is reported. Radiochemical yields have been measured under conditions of varying chelator concentrations, pH (3.5 and 6.5) and temperature (25 and 90 °C). These chelators are: 1,4,7,10-tetraazacyclododecane-1,4,7,10-tetraacetic acid (DOTA), 1,4,7-triazacyclononane-1,4,7-triacetic acid (NOTA), 1,4,7-triazacyclononane macrocycles substituted with phosphonic (NOTP) and phosphinic (TRAP) groups at the amine, bis(2-hydroxybenzyl)ethylenediaminediacetic acid (HBED), a tris(hydroxypyridinone) containing three 1,6-dimethyl-3-hydroxypyridin-4-one groups (THP) and the hexadentate tris(hydroxamate) siderophore desferrioxamine-B (DFO). Competition studies have also been undertaken to assess relative complexation efficiencies of each chelator for 68 Ga 3+ under different pH and temperature conditions. Performing radiolabelling reactions at pH 6.5, 25 °C and 5-50 μM chelator concentration resulted in near quantitative radiochemical yields for all chelators, except DOTA. Radiochemical yields either decreased or were not substantially improved when the reactions were undertaken at lower pH or at higher temperature, except in the case of DOTA. THP and DFO were the most effective 68 Ga 3+ chelators at near-neutral pH and 25 °C, rapidly providing near-quantitative radiochemical yields at very low chelator concentrations. NOTP and HBED were only slightly less effective under these conditions. In competition studies with all other chelators, THP demonstrated highest reactivity for 68 Ga 3+ complexation under all conditions. These data point to THP possessing ideal properties for rapid, one-step kit-based syntheses of 68 Ga-biomolecules for molecular PET imaging. LC-MS and 1 H, 13 C{ 1 H} and 71 Ga NMR studies of HBED complexes of Ga 3+ showed that under the analytical conditions employed in this study, multiple HBED-bound Ga complexes exist. X-ray diffraction data indicated that crystals isolated from these solutions contained octahedral [Ga(HBED)(H 2 O)], with HBED coordinated in a pentadentate N 2 O 3 mode, with only one phenolic group coordinated to Ga 3+ , and the remaining coordination site occupied by a water molecule.

Hydrogen-Rich Gas Production by Cogasification of Coal and Biomass in an Intermittent Fluidized Bed

PubMed Central

Wang, Li-Qun; Chen, Zhao-Sheng

2013-01-01

This paper presents the experimental results of cogasification of coal and biomass in an intermittent fluidized bed reactor, aiming to investigate the influences of operation parameters such as gasification temperature (T), steam to biomass mass ratio (SBMR), and biomass to coal mass ratio (BCMR) on hydrogen-rich (H2-rich) gas production. The results show that H2-rich gas free of N2 dilution is produced and the H2 yield is in the range of 18.25~68.13 g/kg. The increases of T, SBMR, and BCMR are all favorable for promoting the H2 production. Higher temperature contributes to higher CO and H2 contents, as well as H2 yield. The BCMR has a weak influence on gas composition, but the yield and content of H2 increase with BCMR, reaching a peak at the BCMR of 4. The H2 content and yield in the product gas increase with SBMR, whilst the content of CO increases first and then decreases correspondingly. At a typical case, the relative linear sensitivity coefficients of H2 production efficiency to T, SBMR, and BCMR were calculated. The results reveal that the order of the influence of the operation parameters on H2 production efficiency is T > SBMR > BCMR. PMID:24174911

Broiler responsiveness (Ross x 708) to diets varying in amino acid density.

PubMed

Kidd, M T; Corzo, A; Hoehler, D; Miller, E R; Dozier, W A

2005-09-01

Sex-separate male and female broilers (2,592 broilers; Ross x 708) were placed in 144 floor pens (12 replications per treatment) and fed diets containing high (H) and moderate (M) amino acid density from 1 to 55 d of age. Diets were formulated using ileal digestible amino acid ratios to Lys. Six dietary treatment combinations (MMMMM, HMMMM, HHMMM, HHHMM, HHHHM, and HHHHH) were implemented in 5 diet phases (1 to 5, 6 to 14, 15 to 35, 36 to 45, and 46 to 55 d of age). Male birds were heavier (P < or = 0.05) and had lower (P < or = 0.05) feed conversion, abdominal fat, and breast yield than female birds. Birds fed H diets in the first 3 phases had optimal (P < or = 0.05) BW and feed conversion (d 35, and 45), but optimal (P < or = 0.05) feed conversion at d 55 warranted H diets in all phases. Breast meat (d 35) and carcass (d 55) relative to BW were highest (P < or = 0.05) in birds fed H diets in the first 3 phases; however, differences in 55 d breast meat yield did not occur. Results indicate that amino acid needs of Ross x 708 broilers are most critical from 1 to 35 d of age. Predicted economic margins were advantageous in birds fed H diets resulting in dollar 0.12 and dollar 0.05/bird more income over feed costs at 35 and 55 d, respectively, in comparison with birds fed M diets.

Carbon source pulsed feeding to attain high yield and high productivity in poly(3-hydroxybutyrate) (PHB) production from soybean oil using Cupriavidus necator.

PubMed

Pradella, José Geraldo da Cruz; Ienczak, Jaciane Lutz; Delgado, Cecília Romero; Taciro, Marilda Keico

2012-06-01

Poly(3-hydroxybutyrate) (PHB) biosynthesis from soybean oil by Cupriavidus necator was studied using a bench scale bioreactor. The highest cell concentration (83 g l(-1)) was achieved using soybean oil at 40 g l(-1) and a pulse of the same concentration. The PHB content was 81% (w/w), PHB productivity was 2.5 g l(-1) h(-1), and the calculated Y(p/s) value was 0.85 g g(-1). Growth limitation and the onset of PHB biosynthesis took place due to exhaustion of P, and probably also Cu, Ca, and Fe.

Bioethanol produced from Moringa oleifera seeds husk

NASA Astrophysics Data System (ADS)

Ali, E. N.; Kemat, S. Z.

2017-06-01

This paper presents the potential of bioethanol production from Moringa oleifera seeds husk which contains lignocellulosic through Simultaneous Saccharification and Fermentation (SSF) process by using Saccharomyces cerevisiae. This paper investigates the parameters which produce optimum bioethanol yield. The husk was hydrolyzed using NaOH and fermented using Saccharomyces cerevisiae yeast. Batch fermentation was performed with different yeast dosage of 1, 3, and 5 g/L, pH value was 4.5, 5.0 and 5.5, and fermentation time of 3, 6, 9 and 12 hours. The temperature of fermentation process in incubator shaker is kept constant at 32ºC. The samples are then filtered using a 0.20 μm nylon filter syringe. The yield of bioethanol produced was analysed using High Performance Liquid Chromatography (HPLC). The results showed that the highest yield of 29.69 g/L was obtained at 3 hours of fermentation time at pH of 4.5 and using 1g/L yeast. This research work showed that Moringa oleifera seeds husk can be considered to produce bioethanol.

Effect of Electric Field on CO2 Photoreduction by TiO2 Film

NASA Astrophysics Data System (ADS)

Huang, Zhengfeng; Cheng, Xudong; Dong, Peimei; Zhang, Xiwen

2017-02-01

To mitigate the greenhouse effect, many studies have been carried out to improve the CO2 conversion efficiency of TiO2. Modification of TiO2 has been intensively investigated, but the influence of an electric field on photoreduction by this material remains largely unknown. Accordingly, in this study, we explored the effect of an electric field on the photoreduction process using a porous TiO2-Ti material. The results indicated that the CO yield improved 85-fold (equivalent to 4772 μmol/g h) when a 30-kV voltage was applied during the reduction process. To make the electric field effect fully functional, we also explored the effect of water on the photoreduction process, finding that TiO2 showed the highest conversion rate when the humidity was controlled at 50% relative humidity (RH).

Toward Homosuccinate Fermentation: Metabolic Engineering of Corynebacterium glutamicum for Anaerobic Production of Succinate from Glucose and Formate

PubMed Central

Litsanov, Boris; Brocker, Melanie

2012-01-01

Previous studies have demonstrated the capability of Corynebacterium glutamicum for anaerobic succinate production from glucose under nongrowing conditions. In this work, we have addressed two shortfalls of this process, the formation of significant amounts of by-products and the limitation of the yield by the redox balance. To eliminate acetate formation, a derivative of the type strain ATCC 13032 (strain BOL-1), which lacked all known pathways for acetate and lactate synthesis (Δcat Δpqo Δpta-ackA ΔldhA), was constructed. Chromosomal integration of the pyruvate carboxylase gene pycP458S into BOL-1 resulted in strain BOL-2, which catalyzed fast succinate production from glucose with a yield of 1 mol/mol and showed only little acetate formation. In order to provide additional reducing equivalents derived from the cosubstrate formate, the fdh gene from Mycobacterium vaccae, coding for an NAD+-coupled formate dehydrogenase (FDH), was chromosomally integrated into BOL-2, leading to strain BOL-3. In an anaerobic batch process with strain BOL-3, a 20% higher succinate yield from glucose was obtained in the presence of formate. A temporary metabolic blockage of strain BOL-3 was prevented by plasmid-borne overexpression of the glyceraldehyde 3-phosphate dehydrogenase gene gapA. In an anaerobic fed-batch process with glucose and formate, strain BOL-3/pAN6-gap accumulated 1,134 mM succinate in 53 h with an average succinate production rate of 1.59 mmol per g cells (dry weight) (cdw) per h. The succinate yield of 1.67 mol/mol glucose is one of the highest currently described for anaerobic succinate producers and was accompanied by a very low level of by-products (0.10 mol/mol glucose). PMID:22389371

Two-hour post-challenge glucose is a better predictor of adverse outcome after myocardial infarction than fasting or admission glucose in patients without diabetes.

PubMed

Chattopadhyay, Sudipta; George, Anish; John, Joseph; Sathyapalan, Thozhukat

2018-05-01

We evaluate prevalence of new abnormal glucose tolerance (AGT) in post-MI survivors without known diabetes (DM) if guidelines are followed and compare the ability of admission (APG), fasting (FPG) and 2-h post-load plasma glucose (2h-PG) to predict prognosis. A total of 674 patients were followed up for 4 years for incidence of major adverse cardiovascular events (MACE) of cardiovascular death, non-fatal re-infarction or non-haemorrhagic stroke. Ability of models including APG, FPG and 2h-PG to predict MACE was compared. Of the total, 93-96% of impaired glucose tolerance and 64-75% of DM would be missed with current guidelines. MACE was higher in the upper quartiles of 2h-PG. When 2h-PG and FPG were included simultaneously in models, only 2h-PG predicted MACE (HR 1.12, CI 1.04-1.20, p = 0.0012), all cause mortality (HR 1.17, CI 1.05-1.30, p = 0.0039), cardiovascular mortality (HR 1.17, CI 1.02-1.33, p = 0.0205) and non-fatal MI (HR 1.10, CI 1.01-1.20, p = 0.0291). Adding 2h-PG significantly improved ability of models including FPG (χ 2  = 16.01, df = 1, p = 0.0001) or FPG and APG (χ 2  = 17.36, df = 1, p = 0.000) to predict MACE. Model including 2h-PG only had the lowest Akaike's information criteria and highest Akaike weights suggesting that this was the best in predicting events. Adding 2h-PG to models including FPG or APG with other co-variates yielded continuous net reclassification improvement (NRI) of 0.22 (p = 0.026) and 0.27 (p = 0.005) and categorical NRI of 0.09 (p = 0.032) and 0.12 (p = 0.014), respectively. Adding 2 h-PG to models including only FPG, only APG and both yielded integrated discrimination improvement of 0.012 (p = 0.015), 0.022 (p = 0.001) and 0.013 (p = 0.014), respectively. AGT is under-diagnosed on current guidelines. 2h-PG is a better predictor of prognosis compared to APG and FPG.

Preparation and characterisation of the oligosaccharides derived from Chinese water chestnut polysaccharides.

PubMed

Wu, Sheng-Jun; Yu, Lin

2015-08-15

Hydrogen peroxide (H2O2) is a strong oxidant that cleaves glycosidic bonds in polysaccharides. In this study, the oligosaccharides were prepared by removing the starch from Chinese water chestnuts through hydrolysis using α-amylase and then hydrolysing the remaining polysaccharides with H2O2, during which the oligosaccharide yield was monitored. The yield of oligosaccharide was affected by reaction time, temperature, and H2O2 concentration. Extended reaction times, high temperatures, and high H2O2 concentrations decreased oligosaccharide yield. Under optimum conditions (i.e., reaction time of 4h, reaction temperature of 80°C, and 2.5% H2O2 concentration), the maximum oligosaccharide yield was 3.91%. The oligosaccharides derived from Chinese water chestnuts polysaccharides exhibited strong hydroxyl and 2,2-diphenyl-β-picrylhydrazyl radical scavenging activity when applied at a concentration of 100 μg/mL. The results indicate that the oligosaccharides derived from Chinese water chestnuts polysaccharides possessed good antioxidant properties and can be developed as a new dietary supplement and functional food. Copyright © 2015 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yusa, Kazuyuki; Yamamoto, Osamu; Fukuda, Masayuki

Highlights: {yields} We isolated the Zn{sup 2+} ions (eluted Zn{sup 2+} ion; EZ) from zinc-incorporated titanium implant. {yields} The EZ promoted the cell viability in hBMCs. {yields} The EZ stimulated preosteoblast and osteoblast marker gene expression in hBMCs. {yields} The hBMCs supplemented with EZ showed typically cell morphology when osteoblast maturing. {yields} It is revealed that the EZ also stimulates the calcium deposition of hBMCs. -- Abstract: Zinc is one of the trace elements which induce the proliferation and the differentiation of the osteoblast. In the previous study, we found that zinc ions (Zn{sup 2+} ion)-releasing titanium implants had excellentmore » bone fixation using a rabbit femurs model. In this study, we isolated the Zn{sup 2+} ions (eluted Zn{sup 2+} ion; EZ) released from the implant surface, and evaluated the effect of EZ on the osteogenesis of human bone marrow-derived mesenchymal cells (hBMCs). In the result, it was found that the EZ stimulated cell viability, osteoblast marker gene (type I collagen, osteocalcin (OC), alkaline phosphatase (ALP) and bone sialoprotein (BSP)) expressions and calcium deposition in hBMCs.« less

TiO2 films photocatalytic activity improvements by swift heavy ions irradiation

NASA Astrophysics Data System (ADS)

Rafik, Hazem; Mahmoud, Izerrouken; Mohamed, Trari; Abdenacer, Benyagoub

2014-08-01

TiO2 thin films synthesized by sol-gel on glass substrates are irradiated by 90 MeV Xe ions at various fluences and room temperature under normal incidence. The structural, electrical, optical and surface topography properties before and after Xe ions irradiation are investigated. X-ray diffraction (XRD) reveals that the crystallinity is gradually destroyed, and the films become amorphous above 5×1012 ions/cm2. The band gap is not affected by Xe ions irradiation as evidenced from the optical measurements. By contrast, the conductivity increases with raising Xe fluence. The energy band diagram established from the electrochemical characterization shows the feasibility of TiO2 films for the photo-electrochemical chromate reduction. Xe ion irradiation results in enhanced photocatalytic activity in aquatic medium, evaluated by the reduction of Cr(VI) into trivalent state. TiO2 films irradiated at 1013 Xe/cm2 exhibit the highest photoactivity; 69% of chromate (10 ppm) is reduced at pH 3 after 4 h of exposure to sunlight (1120 mW cm-2) with a quantum yield of 0.06%.

Blowpipe Mineralogy for Physics/Environment: Highest-Possible-Tc SuperConductor (Beyond: (but via!!!) MgB2, Cuprates, Pnictides) Quest; BOTH PERMANENT FOREVER Carb-IDES SOLID-State Sequestration AND Drought(s)-Elimination

NASA Astrophysics Data System (ADS)

Segler, Kurt; Williams, Wendell; Siegel, Edward

2011-03-01

Detailed are old blowpipe new applications: charcoal-block reduction of borates to yield ("N-NW" of MgB2) Overhauser-[PR 35,1,411(1987); Intl.J.Mod.Phys.1, 2 & 4, 927(1987)]-"land" predicted high-EST-POSSIBLE Tc SC "LiD2"; very-early: Siegel[Phys.Stat.Sol.(a)11,45(1972);Semiconductors.and Insulators 5: 39,47,62(1979)] carb-IDES SOLID-state phase-TRANSITIONED CHEMICALLY-REDOX"-REACTED STABLE PERMANENT LONG-term NOT "CO2" BUT C-sequestration: PROFITABLE "Grab and Sell" TRUMPS "cap and trade"!!!; Mott alloying/vertical metal-insulator transitions in "borax-(GLASS)-beads"; and very-earlySiegel [{3rd Intl.Conf.Alt.Energy }(1980)-vol.5/p.459!!!] "FLYING-WATER" Hindenberg-effect (H2-UP;H2O-DOWN) via Hydrogen-maximal-Archimedes-buoyancy "chemical-rain-in-pipelines", only via Siegel proprietary "magnetic-hydrogen-valve"(MHV): Renewables-Hydrogen-Water flexible versatile agile scaleable retrofitable integrated operating-system for PERMANENT drought(s)-elimination FOREVER!!!

Boosting subsurface life: is subseafloor sediment a natural catalyst for radiolytic hydrogen production?

NASA Astrophysics Data System (ADS)

Sauvage, J.; Graham, D.; Spivack, A. J.; Dunlea, A. G.; Murray, R. W.; D'Hondt, S.

2014-12-01

Naturally occurring production of molecular hydrogen (H2) by water radiolysis may be a fundamentally important source of electron donors (energy) for life in subsurface environments where organic matter is scarce. Previous studies with very high gamma radiation rates and wet mineral phases have reported high H2 production relative to production from water radiolysis in the absence of solid phases. Numerical calculations by other previous studies have predicted enhanced H2 production from seawater radiolysis relative to pure water radiolysis, due to the interaction of anions with hydroxyl radicals. Given these reports, the potential catalytic influences of solid and dissolved chemical phases on radiolytic H2 production need to be carefully quantified in order to fully evaluate the role of radiolytic H2 as a microbial energy source. For such quantification, we undertook gamma-irradiation experiments with pure water, deep ocean water and mixtures (slurries, φ = 0.85) of seawater with: North Pacific abyssal clay and calcareous oozes, coastal sediment, zirconium dioxide, and zeolite. We carried out our experiments at the Rhode Island Nuclear Science Center using a 37Cesium source at low dose rates (up to 0.1 Gy/hr). Our results to date include the following. First, the per-dose radiolytic H2 yield of pure water at low dose rates is directly comparable to the per-dose yield at much higher dose rates (ca. 1 kGy/hr); this result indicates that H2 production rate is linearly related to radiation dose rate across four orders of magnitude. Second, there is no statistically significant difference (90% confidence limit) between the radiolytic H2 yield from pure water and that from seawater; this result rules out influence of abundant seawater salts on H2 yield from water radiolysis. Third, H2 production from a mixture of abyssal clay and seawater is 25% higher than the yield from pure water. This enhanced yield is consistent with catalysis of radiolytic H2 production by zeolite.

Mixed culture polyhydroxyalkanoate (PHA) synthesis from nutrient rich wet oxidation liquors.

PubMed

Wijeyekoon, Suren; Carere, Carlo R; West, Mark; Nath, Shresta; Gapes, Daniel

2018-09-01

Organic waste residues can be hydrothermally treated to produce organic acid rich liquors. These hydrothermal liquors are a potential feedstock for polyhydroxyalkanoate (PHA) production. We investigated the effect of dissolved oxygen concentration and substrate feeding regimes on PHA accumulation and yield using two hydrothermal liquors derived from a mixture of primary and secondary municipal wastewater treatment sludge and food waste. The enriched culture accumulated a maximum of 41% PHA of cell dry weight within 7 h; which is among the highest reported for N and P rich hydrothermal liquors. Recovered PHA was 77% polyhydroxybutyrate and 23% polyhydroxyvalerate by mass. The families Rhodocyclaceae (84%) and Saprospiraceae (20.5%) were the dominant Proteobacteria (73%) in the enriched culture. The third most abundant bacterial genus, Bdellovibrio, includes species of known predators of PHA producers which may lead to suboptimal PHA accumulation. The PHA yield was directly proportional to DO concentration for ammonia stripped liquor (ASL) and inversely proportional to DO concentration for low strength liquor (LSL). The highest yield of 0.50 Cmol PHA/Cmol substrate was obtained for ASL at 25% DO saturation. A progressively increasing substrate feeding regime resulted in increased PHA yields. These findings demonstrate that substrate feeding regime and oxygen concentration can be used to control the PHA yield and accumulation rate thereby enhancing PHA production viability from nutrient rich biomass streams. Copyright © 2018 Elsevier Ltd. All rights reserved.

Growth and yield responses of field-grown sweetpotato to elevated carbon dioxide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Biswas, P.K.; Hileman, D.R.; Ghosh, P.P.

1996-09-01

Root crops are important in developing countries, where food supplies are frequently marginal. Increases in atmospheric CO{sub 2} usually lead to increases in plant growth and yield, but little is known about the response of root crops to CO{sub 2} enrichment under field conditions. This experiment was conducted to investigate the effects of CO{sub 2} enrichment on growth and yield of field-grown sweetpotato. Plants were grown in open-top chambers in the field at four CO{sub 2} levels ranging from 354 (ambient) to 665 {mu}mol mol{sup {minus}1} in two growing seasons. Shoot growth was not affected significantly by elevated CO{sub 2}.more » Yield of storage roots increased 46 and 75% at the highest CO{sub 2} level in the 2 yr. The yield enhancement occurred through increases in the number of storage roots in the second year. Storage-root/shoot ratios increased 44% and leaf nitrogen concentrations decreased by 24% at the highest CO{sub 2} level. A comparison of plants grown in the open field to plants grown in open-top chambers at ambient CO{sub 2} concentrations indicated that open-top chambers reduced shoot growth in the first year and storage-root yield in both years. These results are consistent with the majority of CO{sub 2}-enrichment studies done on pot-grown sweetpotato. 37 refs., 2 figs., 5 tabs.« less

Induction of high mitotic index in Petunia suspension cultures by sequential treatment with aphidicolin and colchicine.

PubMed

Guri, A; Zelcer, A; Izhar, S

1984-12-01

Significantly higher than normal mitotic index (MI) values were induced in Petunia cell suspensions following treatments with colchicine, aphidicolin, drastic medium replacement, or a sequential application of aphidicolin and colchicine. This last treatment yielded the highest MI values: cells incubated with 30 μg/ml aphidicolin for 18 h, then cultured in drug-free medium for 8 h and finally exposed to 0.1% colchicine for 8 additional hours exhibited MI of 62.8% and 65.7% respectively, for the two cell lines in study.

Local structure in solid solutions of stabilised zirconia with actinide dioxides (UO{sub 2}, NpO{sub 2})

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walter, Marcus, E-mail: marcus.walter@vkta.d; Somers, Joseph; Bouexiere, Daniel

2011-04-15

The local structure of (Zr,Lu,U)O{sub 2-x} and (Zr,Y,Np)O{sub 2-x} solid solutions has been investigated by extended X-ray absorption fine structure (EXAFS). Samples were prepared by mixing reactive (Zr,Lu)O{sub 2-x} and (Zr,Y)O{sub 2-x} precursor materials with the actinide oxide powders, respectively. Sintering at 1600 {sup o}C in Ar/H{sub 2} yields a fluorite structure with U(IV) and Np(IV). As typical for stabilised zirconia the metal-oxygen and metal-metal distances are characteristic for the different metal ions. The bond lengths increase with actinide concentration, whereas highest adaptation to the bulk stabilised zirconia structure was observed for U---O and Np---O bonds. The Zr---O bond showsmore » only a slight increase from 2.14 A at 6 mol% actinide to 2.18 A at infinite dilution in UO{sub 2} and NpO{sub 2}. The short interatomic distance between Zr and the surrounding oxygen and metal atoms indicate a low relaxation of Zr with respect to the bulk structure, i.e. a strong Pauling behaviour. -- Graphical abstract: Metal-oxygen bond distances in (Zr,Lu,U)O{sub 2-x} solid solutions with different oxygen vacancy concentrations (Lu/Zr=1 and Lu/Zr=0.5). Display Omitted Research Highlights: {yields} EXAFS indicates high U and Np adaption to the bulk structure of stabilised zirconia. {yields} Zr---O bond length is 2.18 A at infinite Zr dilution in UO{sub 2} and NpO{sub 2}. {yields} Low relaxation (strong Pauling behaviour) of Zr explains its low solubility in UO{sub 2}.« less

Collection of gametes from live axolotl, Ambystoma mexicanum, and standardization of in vitro fertilization.

PubMed

Mansour, N; Lahnsteiner, F; Patzner, R A

2011-01-15

This study established the first protocol for collection of gametes from live axolotl, Ambystoma mexicanum, by gentle abdominal massage and in vitro fertilization. To stimulate spermiation and ovulation, human chorionic gonadotrophin (hCG) and Ovopel pellets, which are commercially used to stimulate spawning in fish, were tested. The hCG was more effective than Ovopel pellets and yielded a higher semen volume in the injected males and a shorter response time in the females. Collected semen by this method was already motile and fertile. Fertile eggs could be collected in 3-4 successive collection times after the female has started the typical spawning behaviour. The fertilization condition that yielded the highest hatching rate was mixing semen with eggs before the addition of a fertilization saline solution (20 mmol/l NaCl, 1 mmol/l KCl, 1 mmol/l Mg(2)SO(4), 1 mmol Ca(2)Cl, 3 mmol NaHCO(3), 10 mmol/l Tris, pH 8.5 - Osmolality = 65 mosmol/kg). When the pH of the fertilization solution was increased to ≥ 10, the hatching rate was significantly increased. The use of fertilization solutions with osmolalities of ≥ 150 and ≥ 182 were accompanied with a significant decrease in hatching rates and the appearance of deformed larvae, respectively. In conclusion, a reliable protocol for gamete collection from live axolotl is established as a laboratory model of in vitro fertilization for urodele amphibians. This protocol may be transferable to endangered urodeles. Copyright © 2011 Elsevier Inc. All rights reserved.

Many light Higgs bosons in the next-to-minimal supersymmetric model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dermisek, Radovan; Gunion, John F.

2009-03-01

The next-to-minimal supersymmetric model with a light doubletlike CP-odd Higgs boson and small tan{beta} can satisfy all experimental limits on Higgs bosons even with light superpartners. In these scenarios, the two lightest CP-even Higgs bosons, h{sub 1} and h{sub 2}, and the charged Higgs boson, h{sup +}, can all be light enough to be produced at CERN LEP and yet have decays that have not been looked for or are poorly constrained by existing collider experiments. The channel h{sub 1}{yields}a{sub 1}a{sub 1} with a{sub 1}{yields}{tau}{sup +}{tau}{sup -} or 2j is still awaiting LEP constraints for m{sub h{sub 1}}>86 or 82more » GeV, respectively. LEP data may also contain e{sup +}e{sup -}{yields}h{sub 2}a{sub 1} events where h{sub 2}{yields}Za{sub 1} is the dominant decay, a channel that was never examined. Decays of the charged Higgs bosons are often dominated by H{sup {+-}}{yields}W{sup {+-}}{sup (}*{sup )}a{sub 1} with a{sub 1}{yields}gg, cc, and {tau}{sup +}{tau}{sup -}. This is a channel that has so far been ignored in the search for t{yields}h{sup +}b decays at the Tevatron. A specialized analysis might reveal a signal. The light a{sub 1} might be within the reach of B factories via {upsilon}{yields}{gamma}a{sub 1} decays. We study typical mass ranges and branching ratios of Higgs bosons in this scenario and compare these scenarios where the a{sub 1} has a large doublet component to the more general scenarios with arbitrary singlet component for the a{sub 1}.« less

Heavy metal phytoextraction by Sedum alfredii is affected by continual clipping and phosphorus fertilization amendment.

PubMed

Huang, Huagang; Li, Tingqiang; Gupta, D K; He, Zhenli; Yang, Xiao-E; Ni, Bingnan; Li, Mao

2012-01-01

Improving the efficacy of phytoextraction is critical for its successful application in metal contaminated soils. Mineral nutrition affects plant growth and metal absorption and subsequently the accumulation of heavy metal through hyper-accumulator plants. This study assessed the effects of di-hydrogen phosphates (KH2PO4, Ca(H2PO4)2, NaH2PO4 and NH4H2PO4) application at three levels (22, 88 and 352 mg P/kg soil) on Sedum alfredii growth and metal uptake by three consecutive harvests on aged and Zn/Cd combined contaminated paddy soil. The addition of phosphates (P) significantly increased the amount of Zn taken up by S. alfredii due to increased shoot Zn concentration and dry matter yield (DMY) (P < 0.05). The highest phytoextraction of Zn and Cd was observed in KH2PO4 and NH4H2PO4 treatment at 352 mg P/kg soil. The amount of Zn removed by phytoextraction increased in the order of 1st clipping < 2nd clipping < 3rd clipping, and for Cd extraction the order was 2nd clipping < 1st clipping < 3rd clipping. These results indicate that the application of P fertilizers coupled with multiple cuttings can enhance the removal of Zn and Cd from contaminated soils by S. alfredii, thus shortening the time needed for accomplishing remediation goals.

Analyses of the Post-reflux Swallow-induced Peristaltic Wave Index and Nocturnal Baseline Impedance Parameters Increase the Diagnostic Yield of Impedance-pH Monitoring of Patients With Reflux Disease.

PubMed

Frazzoni, Marzio; Savarino, Edoardo; de Bortoli, Nicola; Martinucci, Irene; Furnari, Manuele; Frazzoni, Leonardo; Mirante, Vincenzo Giorgio; Bertani, Helga; Marchi, Santino; Conigliaro, Rita; Savarino, Vincenzo

2016-01-01

Analyses of impedance parameters such as the post-reflux swallow-induced peristaltic wave (PSPW) index and the mean nocturnal baseline impedance (MNBI) have been proposed to increase the accuracy of diagnosis of reflux disease. We assessed whether these improve the diagnostic yield of impedance pH monitoring of reflux disease. We performed a prospective study of consecutive patients with proton pump inhibitor-responsive heartburn who underwent 24-hour impedance pH monitoring at hospitals in Italy from January 2011 through December 2013. Reviewers blindly analyzed off-therapy impedance pH tracings from 289 patients with proton pump inhibitor-responsive heartburn, 68 with erosive reflux disease and 221 with non-erosive reflux disease (NERD), along with 50 healthy individuals (controls). The PSPW index, the MNBI, the esophageal acid exposure time, the number of total refluxes, and the bolus exposure were calculated, as well as the symptom association probability (SAP) and the symptom index (SI). In receiver operating characteristic analysis, the area under curve of the PSPW index (0.977; 95% confidence interval, 0.961-0.993) was significantly greater than that of the other impedance pH parameters in identifying patients with reflux disease (P < .001). The PSPW index and the MNBI identified patients with erosive reflux disease with the highest level of sensitivity (100% and 91%, respectively), as well as the 118 pH-positive (99% and 86%) and 103 pH-negative (77% and 56%) cases of NERD. The PSPW index and the MNBI identified pH-negative NERD with the highest level of sensitivity; values were 82% and 52% for the 65 SAP-positive and/or SI-positive cases and 68% and 63% for the 38 SAP-negative and SI-negative cases. Diagnoses of NERD were confirmed by pH-only criteria, including those that were positive on the basis of the SAP or SI, for 165 of 221 cases (75%) and by impedance pH criteria for 216 of 221 cases (98%) (P = .001). The PSPW index and the MNBI increase the diagnostic yield of impedance pH monitoring of patients with reflux disease. Analysis of impedance pH data by calculating the PSPW index and the MNBI can increase the accuracy of diagnosis of patients with reflux disease, compared with pH-only data. Copyright © 2016 AGA Institute. Published by Elsevier Inc. All rights reserved.

The prevalence and potential fisheries consequences of Heterosporis sutherlandae in a Minnesota lake.

PubMed

Tomamichel, Megan M; Hodgins, Nathaniel C; Venturelli, Paul A; Phelps, Nicholas B D

2018-01-01

Heterosporis sutherlandae is an emerging microsporidian fish parasite in the Great Lakes region. H. sutherlandae forms lesions in the muscle tissue of fishes important to aquaculture and sport fishing. These lesions render the filet inedible and may have fitness consequences. We evaluated the prevalence and severity of H. sutherlandae among yellow perch (Perca flavescens) in a known-positive Minnesota lake, and used an equilibrium yield model to evaluate impacts on harvest. Twenty-eight percent of the 400 yellow perch sampled were infected with H. sutherlandae. Males were 1.5 times more likely to be infected than females and were more severely infected. The presence of the parasite did not vary with relative weight or age, but infection severity was highest among older individuals that were in better condition. These results suggest that males are more susceptible to infection, and that infection is not associated with maturity or a gape-limiting food source. These results also suggest that heterosporosis increases in severity with time or by increased exposure. Our equilibrium yield model found that a 10% increase in mortality due to H. sutherlandae could result in 30% and 10% reductions in yield and mean catch weight, respectively. The results of this study direct future field sampling and laboratory experiments to further understand and predict the impacts of this parasite.

Effect of agitation rate on ethanol production from sugar maple hemicellulosic hydrolysate by Pichia stipitis.

PubMed

Shupe, Alan M; Liu, Shijie

2012-09-01

Concentrated dilute acid hydrolysate was obtained from hot water extracts of Acer saccharum (sugar maple) and was fermented to ethanol by Pichia stipitis in a 1.3-L-benchtop bioreactor. The conditions under which the highest ethanol yield was achieved were when the air flow rate was set to 100 cm(3) and the agitation rate was set to 150 rpm resulting in an overall mass transfer coefficient (K(L)a) of 0.108 min(-1). A maximum ethanol concentration of 29.7 g/L was achieved after 120 h of fermentation; however, after 90 h of fermentation, the ethanol concentration was only slightly lower at 29.1 g/L with a yield of 0.39 g ethanol per gram of sugar consumed. Using the same air flow rate and adjusting the agitation rate resulted in lower ethanol yields of 0.25 g/g at 50 rpm and 0.30 g/g at 300 rpm. The time it takes to reach the maximum ethanol concentration was also affected by the agitation rate. The ethanol concentration continued to increase even after 130 h of fermentation when the agitation rate was set at 50 rpm, whereas the maximum ethanol concentration was reached after only 68.5 h at 300 rpm.

Enzyme-assisted extraction of stabilized chlorophyll from spinach.

PubMed

Özkan, Gülay; Ersus Bilek, Seda

2015-06-01

Zinc complex formation with chlorophyll derivatives in spinach pulp was studied by adding 300ppm Zn(2+) for production of stable food colorant, followed by the heating at 110°C for 15min. Zinc complex formation increased at pH values of 7.0 or greater. Pectinex Ultra SP-L was selected for enzyme-assisted release of zinc-chlorophyll derivatives from spinach pulp. Effect of enzyme concentration (1-9%), treatment temperature (30-60°C), and time (30-210min) on total chlorophyll content (TCC) were optimized using response surface methodology. A quadratic regression model (R(2)=0.9486) was obtained from the experimental design. Optimum treatment conditions were 8% enzyme concentration, 45°C, and 30min, which yielded a 50.747mgTCC/100g spinach pulp. Enzymatic treatment was followed by solvent extraction with ethanol at a solvent-to-sample ratio of 2.5:1 at 60°C for 45min for the highest TCC recovery. Pretreatment with enzyme and extraction in ethanol resulted in 39% increase in Zn-chlorophyll derivative yield. Copyright © 2014 Elsevier Ltd. All rights reserved.

Direct transformation of xylan-type hemicelluloses to furfural via SnCl₄ catalysts in aqueous and biphasic systems.

PubMed

Wang, Wenju; Ren, Junli; Li, Huiling; Deng, Aojie; Sun, Runcang

2015-05-01

Direct catalytic transformation of xylan-type hemicelluloses to furfural in the aqueous system and the biphasic system were comparatively investigated under mild conditions. Screening of several promising chlorides for conversion of beech xylan in the aqueous system revealed the Lewis acid SnCl4 was the most effective catalyst. Comparing to the single aqueous system, the bio-based 2-methyltetrahydrofuran (2-MTHF)/H2O biphasic system was more conducive to the synthesis of furfural, in which the highest furfural yield of 78.1% was achieved by using SnCl4 as catalysts under the optimized reaction conditions (150°C, 120 min). Additionally, the influences of xylan-type hemicelluloses with different chemical and structural features from beech, corncob and bagasse on the furfural production were studied. It was found that furfural yield to some extent was determined by the xylose content in hemicelluloses and also had relationships with the molecular weight of hemicelluloses and the degree of crystallization. Copyright © 2015 Elsevier Ltd. All rights reserved.

Panax ginseng Fraction F3 Extracted by Supercritical Carbon Dioxide Protects against Oxidative Stress in ARPE-19 Cells

PubMed Central

Yang, Chao-Chin; Chen, Chiu-Yuan; Wu, Chun-Chi; Koo, Malcolm; Yu, Zer-Ran; Wang, Be-Jen

2016-01-01

In our previous work, the ethanolic extract of Panax ginseng C. A. Meyer was successively partitioned using supercritical carbon dioxide at pressures in series to yield residue (R), F1, F2, and F3 fractions. Among them, F3 contained the highest deglycosylated ginsenosides and exerted the strongest antioxidant and anti-inflammatory activities. The aim of this study was to investigate the protective effects of P. ginseng fractions against cellular oxidative stress induced by hydrogen peroxide (H2O2). Viability of adult retinal pigment epithelium-19 (ARPE-19) cells was examined after treatments of different concentrations of fractions followed by exposure to H2O2. Oxidative levels (malondialdehyde (MDA), 8-hydroxydeoxyguanosine (8-OHdG), and reactive oxygen species (ROS)) and levels of activity of antioxidant enzymes were assessed. Results showed that F3 could dose-dependently protected ARPE-19 cells against oxidative injury induced by H2O2. F3 at a level of 1 mg/mL could restore the cell death induced by H2O2 of up to 60% and could alleviate the increase in cellular oxidation (MDA, 8-OHdG, and ROS) induced by H2O2. Moreover, F3 could restore the activities of antioxidant enzymes suppressed by H2O2. In conclusion, F3 obtained using supercritical carbon dioxide fractionation could significantly increase the antioxidant capacity of P. ginseng extract. The antioxidant capacity was highly correlated with the concentration of F3. PMID:27754362

Effect of forms of selenium on the accumulation of selenium, sulfur, and forms of nitrogen and phosphorus in forage cowpea (Vigna sinensis)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Singh, M.; Singh, N.

1979-05-01

The effects of forms of selenium on the accumulation of sulfur, selenium, and forms of nitrogen and phosphorus in cowpea (Vigna sinensis) were studied in pots in the greenhouse at Haryana Agricultural University, Hissar, India. The soil used was sandy, and forms of selenium added were Na/sub 2/SeO/sub 4/ 10H/sub 2/O, Na/sub 2/SeO/sub 3/ 5H/sub 2/O, H/sub 2/SeO/sub 3/, and elemental selenium at the rate of 0, 1, 2.5 and 5 ppM. Dry matter yield and sulfur content decreased with increased selenium application. This inhibition in plants, attributable to applied selenium, was in the order SeO/sub 4/ > H/sub 2/SeO/submore » 3/ > SeO/sub 3/ > elemental selenium. Plant selenium increased with increasing application of all forms of selenium. The highest plant selenium (11.58 ppM) was in the plants treated with SeO/sub 4/, followed by the plants treated with H/sub 2/SeO/sub 3/, SeO/sub 3/, and elemental selenium. The total plant phosphorus increased with increased selenium application in any form, but maximum phosphorus occurred in SeO/sub 3/-treated plants. The inorganic phosphorus increased similarly, the largest amount occurring in SeO/sub 4/-treated plants. Organic phosphorus decreased with selenium application; minimum concentration was recorded in SeO/sub 4/-treated plants. Soluble nitrogen decreased, relative to the control, with applications of 2.5 and 5 ppM selenium. This decrease was minimal for elemental selenium and maximum for SeO/sub 4/. Soluble nitrogen, in the case of SeO/sub 3/ was higher than for H/sub 2/SeO/sub 3/. Total plant nitrogen and protein also decreased. Amino N, amide N, and ammoniacal and nitrate N increased, compared to the control. The largest amount of all these forms was noted in SeO/sub 4/-treated plants. Overall, among the forms of selenium normally reported in soils, the SeO/sub 4/ form showed the highest inhibition, whereas SeO/sub 3/ showed less than both SeO/sub 4/ and H/sub 2/SeO/sub 3/.« less

Optimization of synthesis of the nickel-cobalt oxide based anode electrocatalyst and of the related membrane-electrode assembly for alkaline water electrolysis

NASA Astrophysics Data System (ADS)

Chanda, Debabrata; Hnát, Jaromir; Bystron, Tomas; Paidar, Martin; Bouzek, Karel

2017-04-01

In this work, the Ni-Co spinel oxides are synthesized via different methods and using different calcination temperatures. Properties of the prepared materials are compared. The best route is selected and used to prepare a Ni1+xCo2-xO4 (-1 ≤ x ≤ 1) series of materials in order to investigate their catalytic activity towards the oxygen evolution reaction (OER). The results show that hydroxide preparation yields NiCo2O4 oxide with the highest activity. 325 °C is identified as the optimum calcination temperature. Subsequently, the catalysts are tested in an electrolysis cell. To prepare an anode catalyst layer based on NiCo2O4 catalyst on top of a nickel foam substrate for membrane electrode assembly (MEA) construction, following polymer binders are used: anion-selective quaternized polyphenylene oxide (qPPO), inert polytetrafluoroethylene (PTFE®), and cation-selective Nafion®. qPPO ionomer containing MEA exhibited highest OER activity. The current density obtained using a MEA containing qPPO binder attains a value of 135 mA cm-2 at a cell voltage of 1.85 V. After 7 h chronopotentiometric experiment at a constant current density of 225 mA cm-2, the MEA employing PTFE® binder shows higher stability than the other binders in alkaline water electrolysis at 50 °C. Under similar conditions, stability of the PTFE®-binding MEA is examined for 135 h.

Characterization of Chemical Compounds with Antioxidant and Cytotoxic Activities in Bougainvillea x buttiana Holttum and Standl, (var. Rose) Extracts

PubMed Central

Abarca-Vargas, Rodolfo; Peña Malacara, Carlos F.; Petricevich, Vera L.

2016-01-01

Bougainvillea is widely used in traditional Mexican medicine to treat several diseases. This study was designed to characterize the chemical constituents of B. x buttiana extracts with antioxidant and cytotoxic activities using different solvents. The extraction solvents used were as follows: distilled water (dH2O), methanol (MeOH), acetone (DMK), ethanol (EtOH), ethyl acetate (EtOAc), dichloromethane (DCM), and hexane (Hex) (100%) at an extraction temperature of 26 °C. Analysis of bioactive compounds present in the B. x buttiana extracts included the application of common phytochemical screening assays, GC-MS analysis, and cytotoxicity and antioxidant assays. The results show that the highest extraction yield was observed with water and methanol. The maximum total phenolic content amount and highest antioxidant potential were obtained when extraction with methanol was used. With the exceptions of water and ethanol extractions, all other extracts showed cytotoxicity ranging between 31% and 50%. The prevailing compounds in water, methanol, ethanol, and acetone solvents were as follows: 4H-pyran-4-one, 2,3-dihydro-3, 5-dihydroxy-6-methyl (2), 2-propenoic acid, 3-(2-hydrophenyl)-(E)- (3), and 3-O-methyl-d-glucose (6). By contrast, the major components in the experiments using solvents such as EtOH, DMK, EtOAc, DCM, and Hex were n-hexadecanoic acid (8), 9,12-octadecadienoic acid (Z,Z) (12); 9-octadecenoic acid (E)- (13), and stigmasta-5,22-dien-3-ol (28). PMID:27918436

Influence of silica–alumina support ratio on H2 production and catalyst carbon deposition from the Ni-catalytic pyrolysis/reforming of waste tyres

PubMed Central

Zhang, Yeshui; Tao, Yongwen; Huang, Jun; Williams, Paul

2017-01-01

The influence of catalyst support alumina–silica in terms of different Al2O3 to SiO2 mole ratios containing 20 wt.% Ni on the production of hydrogen and catalyst coke formation from the pyrolysis-catalysis of waste tyres is reported. A two-stage reactor system was used with pyrolysis of the tyres followed by catalytic reaction. There was only a small difference in the total gas yield and hydrogen yield by changing the Al2O3 to SiO2 mole ratios in the Ni-Al2O3/SiO2 catalyst. The 1:1 ratio of Al2O3:SiO2 ratio produced the highest gas yield of 27.3 wt.% and a hydrogen production of 14.0 mmol g-1tyre. Catalyst coke formation decreased from 19.0 to 13.0 wt.% as the Al2O3:SiO2 ratio was changed from 1:1 to 2:1, with more than 95% of the coke being filamentous-type carbon, a large proportion of which was multi-walled carbon nanotubes. Further experiments introduced steam to the second-stage reactor to investigate hydrogen production for the pyrolysis-catalytic steam reforming of the waste tyres using the 1:1 Al2O3/SiO2 nickel catalyst. The introduction of steam produced a marked increase in total gas yield from ~27 wt. % to ~58 wt.%; in addition, hydrogen production was increased to 34.5 mmol g-1 and there was a reduction in catalyst coke formation to 4.6 wt.%. PMID:28789599

Influence of silica-alumina support ratio on H2 production and catalyst carbon deposition from the Ni-catalytic pyrolysis/reforming of waste tyres.

PubMed

Zhang, Yeshui; Tao, Yongwen; Huang, Jun; Williams, Paul

2017-10-01

The influence of catalyst support alumina-silica in terms of different Al 2 O 3 to SiO 2 mole ratios containing 20 wt.% Ni on the production of hydrogen and catalyst coke formation from the pyrolysis-catalysis of waste tyres is reported. A two-stage reactor system was used with pyrolysis of the tyres followed by catalytic reaction. There was only a small difference in the total gas yield and hydrogen yield by changing the Al 2 O 3 to SiO 2 mole ratios in the Ni-Al 2 O 3 /SiO 2 catalyst. The 1:1 ratio of Al 2 O 3 :SiO 2 ratio produced the highest gas yield of 27.3 wt.% and a hydrogen production of 14.0 mmol g -1 tyre . Catalyst coke formation decreased from 19.0 to 13.0 wt.% as the Al 2 O 3 :SiO 2 ratio was changed from 1:1 to 2:1, with more than 95% of the coke being filamentous-type carbon, a large proportion of which was multi-walled carbon nanotubes. Further experiments introduced steam to the second-stage reactor to investigate hydrogen production for the pyrolysis-catalytic steam reforming of the waste tyres using the 1:1 Al 2 O 3 /SiO 2 nickel catalyst. The introduction of steam produced a marked increase in total gas yield from ~27 wt. % to ~58 wt.%; in addition, hydrogen production was increased to 34.5 mmol g -1 and there was a reduction in catalyst coke formation to 4.6 wt.%.

Synthesis, characterization, conductivity and antimicrobial study of a novel thermally stable polyphenol containing azomethine group

NASA Astrophysics Data System (ADS)

Yılmaz Baran, Nuray; Karakışla, Meral; Demir, Hacı Ökkeş; Saçak, Mehmet

2016-11-01

Poly(4-[[(4-methylphenyl)methylene]amino]phenol) (P(4-MMAP)), which is a Schiff base polymer, was synthesized by an oxidative polycondensation reaction of 4-[[(4-methylphenyl)methylene]amino]phenol (4-MMAP) with the oxidants NaOCl, H2O2 and O2 in an aqueous alkaline medium. The polymerizations were carried out at various temperatures and times, and the highest polymer yield could be obtained when using 37% with NaOCl oxidant. The structures of the monomer and polymer were characterized by UV-Vis, FTIR 1H NMR and X-ray diffraction techniques. The thermal behaviors of the monomer and polymer were identified by the TG and DTG techniques. The thermal degradation of the polymer which was observed thermally stable up to 1000 °C, was also supported by the Thermo-IR spectra recorded in the temperature range of 25-800 °C. The number average molecular weight (Mn), weight average molecular weight (Mw) and polydispersity index (PDI) of the polymer were found to be 16682, 57796 g/mol and 3.4, respectively. The highest electrical conductivity value of P(4-MMAP) doped with iodine vapor at different temperatures and times was measured to be 7.8 × 10-5 Scm-1 after doping for 48 h at 60 °C. The antibacterial and antifungal activities of 4-MMAP and P(4-MMAP) were also assayed against the bacteria Sarcina lutea, Enterobacter aerogenes, Escherichia coli, Enterococcus faecalis, Klebsiella pneumoniae, Bacillus subtilis and the fungi Candida albicans, Saccharomyces cerevisiae, respectively.

Adsorption of Cd2+ on carboxyl-terminated superparamagnetic iron oxide nanoparticles.

PubMed

Feng, Zhange; Zhu, Shun; Martins de Godoi, Denis Ricardo; Samia, Anna Cristina S; Scherson, Daniel

2012-04-17

The affinity of Cd(2+) toward carboxyl-terminated species covalently bound to monodisperse superparamagnetic iron oxide nanoparticles, Fe(3)O(4)(np)-COOH, was investigated in situ in aqueous electrolytes using rotating disk electrode techniques. Strong evidence that the presence of dispersed Fe(3)O(4)(np)-COOH does not affect the diffusion limiting currents was obtained using negatively and positively charged redox active species in buffered aqueous media (pH = 7) devoid of Cd(2+). This finding made it possible to determine the concentration of unbound Cd(2+) in solutions containing dispersed Fe(3)O(4)(np)-COOH, 8 and 17 nm in diameter, directly from the Levich equation. The results obtained yielded Cd(2+) adsorption efficiencies of ~20 μg of Cd/mg of Fe(3)O(4)(np)-COOH, which are among the highest reported in the literature employing ex situ methods. Desorption of Cd(2+) from Fe(3)O(4)(np)-COOH, as monitored by the same forced convection method, could be accomplished by lowering the pH, a process found to be highly reversible.

Novel Halomonas sp. B15 isolated from Larnaca Salt Lake in Cyprus that generates vanillin and vanillic acid from ferulic acid.

PubMed

Vyrides, Ioannis; Agathangelou, Maria; Dimitriou, Rodothea; Souroullas, Konstantinos; Salamex, Anastasia; Ioannou, Aristostodimos; Koutinas, Michalis

2015-08-01

Vanillin is a high value added product with many applications in the food, fragrance and pharmaceutical industries. A natural and low-cost method to produce vanillin is by microbial bioconversions through ferulic acid. Until now, limited microorganisms have been found capable of bioconverting ferulic acid to vanillin at high yield. This study aimed to screen halotolerant strains of bacteria from Larnaca Salt Lake which generate vanillin and vanillic acid from ferulic acid. From a total of 50 halotolenant/halophilic strains 8 grew in 1 g/L ferulic acid and only 1 Halomonas sp. B15 and 3 Halomonas elognata strains were capable of bioconverting ferulic acid to vanillic acid at 100 g NaCl/L. The highest vanillic acid (365 mg/L) at these conditions generated by Halomonas sp. B15 which corresponds to ferulic acid bioconversion yield of 36.5%. Using the resting cell technique with an initial ferulic acid concentration of 0.5 g/L at low salinity, the highest production of vanillin (245 mg/L) took place after 48 h, corresponding to a bioconversion yield of 49%. This is the first reported Halomonas sp. with high yield of vanillin production from ferulic acid at low salinity.

Optimisation of novel method for the extraction of steviosides from Stevia rebaudiana leaves.

PubMed

Puri, Munish; Sharma, Deepika; Barrow, Colin J; Tiwary, A K

2012-06-01

Stevioside, a diterpene glycoside, is well known for its intense sweetness and is used as a non-caloric sweetener. Its potential widespread use requires an easy and effective extraction method. Enzymatic extraction of stevioside from Stevia rebaudiana leaves with cellulase, pectinase and hemicellulase, using various parameters, such as concentration of enzyme, incubation time and temperature, was optimised. Hemicellulase was observed to give the highest stevioside yield (369.23±0.11μg) in 1h in comparison to cellulase (359±0.30μg) and pectinases (333±0.55μg). Extraction from leaves under optimised conditions showed a remarkable increase in the yield (35 times) compared with a control experiment. The extraction conditions were further optimised using response surface methodology (RSM). A central composite design (CCD) was used for experimental design and analysis of the results to obtain optimal extraction conditions. Based on RSM analysis, temperature of 51-54°C, time of 36-45min and the cocktail of pectinase, cellulase and hemicellulase, set at 2% each, gave the best results. Under the optimised conditions, the experimental values were in close agreement with the prediction model and resulted in a three times yield enhancement of stevioside. The isolated stevioside was characterised through 1 H-NMR spectroscopy, by comparison with a stevioside standard. Copyright © 2011 Elsevier Ltd. All rights reserved.

Supersaturation of dissolved H(2) and CO (2) during fermentative hydrogen production with N(2) sparging.

PubMed

Kraemer, Jeremy T; Bagley, David M

2006-09-01

Dissolved H(2) and CO(2) were measured by an improved manual headspace-gas chromatographic method during fermentative H(2) production with N(2) sparging. Sparging increased the yield from 1.3 to 1.8 mol H(2)/mol glucose converted, although H(2) and CO(2) were still supersaturated regardless of sparging. The common assumption that sparging increases the H(2) yield because of lower dissolved H(2) concentrations may be incorrect, because H(2) was not lowered into the range necessary to affect the relevant enzymes. More likely, N(2) sparging decreased the rate of H(2) consumption via lower substrate concentrations.

Optimizing Phosphoric Acid plus Hydrogen Peroxide (PHP) Pretreatment on Wheat Straw by Response Surface Method for Enzymatic Saccharification.

PubMed

Qiu, Jingwen; Wang, Qing; Shen, Fei; Yang, Gang; Zhang, Yanzong; Deng, Shihuai; Zhang, Jing; Zeng, Yongmei; Song, Chun

2017-03-01

Wheat straw was pretreated by phosphoric acid plus hydrogen peroxide (PHP), in which temperature, time, and H 3 PO 4 proportion for pretreatment were investigated by using response surface method. Results indicated that hemicellulose and lignin removal positively responded to the increase of pretreatment temperature, H 3 PO 4 proportion, and time. H 3 PO 4 proportion was the most important variable to control cellulose recovery, followed by pretreatment temperature and time. Moreover, these three variables all negatively related to cellulose recovery. Increasing H 3 PO 4 proportion can improve enzymatic hydrolysis; however, reduction on cellulose recovery results in decrease of glucose yield. Extra high temperature or long time for pretreatment was not beneficial to enzymatic hydrolysis and glucose yield. Based on the criterion for minimizing H 3 PO 4 usage and maximizing glucose yield, the optimized pretreatment conditions was 40 °C, 2.0 h, and H 3 PO 4 proportion of 70.2 % (H 2 O 2 proportion of 5.2 %), by which glucose yielded 299 mg/g wheat straw (946.2 mg/g cellulose) after 72-h enzymatic hydrolysis.

[Effects of different patterns surface mulching on soil properties and fruit trees growth and yield in an apple orchard].

PubMed

Zhang, Yi; Xie, Yong-Sheng; Hao, Ming-De; She, Xiao-Yan

2010-02-01

Taking a nine-year-old Fuji apple orchard in Loess Plateau as test object, this paper studied the effects of different patterns surface mulching (clean tillage, grass cover, plastic film mulch, straw mulch, and gravel mulch) on the soil properties and fruit trees growth and yield in this orchard. Grass cover induced the lowest differentiation of soil moisture profile, while gravel mulch induced the highest one. In treatment gravel mulch, the soil moisture content in apple trees root zone was the highest, which meant that there was more water available to apple trees. Surface mulching had significant effects on soil temperature, and generally resulted in a decrease in the maximum soil temperature. The exception was treatment plastic film mulch, in which, the soil temperature in summer exceeded the maximum allowable temperature for continuous root growth and physiological function. With the exception of treatment plastic film mulch, surface mulching increased the soil CO2 flux, which was the highest in treatment grass cover. Surface mulching also affected the proportion of various branch types and fruit yield. The proportion of medium-sized branches and fruit yield were the highest in treatment gravel mulch, while the fruit yield was the lowest in treatment grass cover. Factor analysis indicated that among the test surface mulching patterns, gravel mulch was most suitable for the apple orchards in gully region of Loess Plateau.

Middle atmosphere heating by exothermic chemical reactions involving odd-hydrogen species

NASA Technical Reports Server (NTRS)

Mlynczak, Martin G.; Solomon, Susan

1991-01-01

The rate of heating which occurs in the middle atmosphere due to four exothermic reactions involving members of the odd-hydrogen family is calculated. The following reactions are considered: O + OH yields O2 + H; H + O2 + M yields HO2 + M; H + O3 yields OH + O2; and O + HO2 yields OH + O2. It is shown that the heating rates due to these reactions rival the oxygen-related heating rates conventionally considered in middle-atmosphere models. The conversion of chemical potential energy into molecular translational energy (heat) by these odd-hydrogen reactions is shown to be a significant energy source in the middle atmosphere that has not been previously considered.

Experiments with planar inductive ion source meant for creation of H+ beams.

PubMed

Vainionpaa, J H; Kalvas, T; Hahto, S K; Reijonen, J

2007-06-01

In this article the effects of different engineering parameters of rf-driven ion sources with an external spiral antenna and a quartz rf window are studied. This article consists of three main topics: the effect of source geometry on the operation gas pressure, the effect of source materials and magnetic confinement on extracted current density and ion species, and the effect of different antenna geometries on the extracted current density. The effect of source geometry was studied using three cylindrical plasma chambers with different inner diameters. The chamber materials were studied using two materials, aluminum (Al) and alumina (Al(2)O(3)). The removable 14 magnet multicusp confinement arrangement enabled us to compare the effects of the two wall materials with and without the magnetic confinement. The highest measured proton fractions were measured using Al(2)O(3) plasma chamber and no multicusp confinement. For the compared ion sources the source with multicusp confinement and Al(2)O(3) plasma chamber yields the highest current densities. Multicusp confinement increased the maximum extracted current by up to a factor of 2. Plasma production with different antenna geometries were also studied. The highest current density was achieved using 4.5 loop solenoid antenna with 6.0 cm diameter. A slightly lower current density with lower pressure was achieved using a tightly wound 3 loop spiral antenna with 3.3 cm inner diameter and 6 cm outer diameter.

Yield and seed oil content response of dwarf, rapid-cycling Brassica to nitrogen treatments, planting density, and carbon dioxide enrichment

NASA Technical Reports Server (NTRS)

Frick, J.; Nielsen, S. S.; Mitchell, C. A.

1994-01-01

Effects of N level (15 to 30 mM), time of N increase (14 to 28 days after planting), and planting density (1163 to 2093 plants/m2) were determined for crop yield responses of dwarf, rapid-cycling brassica (Brassica napus L., CrGC 5-2, Genome: ACaacc). Crops were grown in solid-matrix hydroponic systems and under controlled-environment conditions, including nonsupplemented (ambient) or elevated CO2 concentrations (998 +/- 12 micromoles mol-1). The highest seed yield rate obtained (4.4 g m-2 day-1) occurred with the lowest N level (15 mM) applied at the latest treatment time (day 28). In all trials, CO2 enrichment reduced seed yield rate and harvest index by delaying the onset of flowering and senescence and stimulating vegetative shoot growth. The highest shoot biomass accumulation rate (55.5 g m-2 day-1) occurred with the highest N level (30 mM) applied at the earliest time (day 14). Seed oil content was not significantly affected by CO2 enrichment. Maximum seed oil content (30% to 34%, dry weight basis) was obtained using the lowest N level (15 mM) initiated at the latest treatment time (day 28). In general, an increase in seed oil content was accompanied by a decrease in seed protein. Seed carbohydrate, moisture, and ash contents did not vary significantly in response to experimental treatments. Effects of N level and time of N increase were consistently significant for most crop responses. Planting density was significant only under elevated CO2 conditions.

Evaluation of the integrated hydrothermal carbonization-algal cultivation process for enhanced nitrogen utilization in Arthrospira platensis production.

PubMed

Yao, Changhong; Wu, Peichun; Pan, Yanfei; Lu, Hongbin; Chi, Lei; Meng, Yingying; Cao, Xupeng; Xue, Song; Yang, Xiaoyi

2016-09-01

Sustainable microalgal cultivation at commercial scale requires nitrogen recycling. This study applied hydrothermal carbonization to recover N of hot-water extracted Arthrospira platensis biomass residue into aqueous phase (AP) under different operation conditions and evaluated the N utilization, biomass yield and quality of A. platensis cultures using AP as the sole N source. With the increase of temperature at 190-210°C or reaction time of 2-3h, the N recovery rate decreased under nitrogen-repletion (+N) cultivation, while contrarily increased under nitrogen-limitation (-N) cultivation. Under +N biomass accumulation in the cultures with AP under 190°C was enhanced by 41-67% compared with that in NaNO3, and the highest protein content of 51.5%DW achieved under 200°C-2h was also 22% higher. Carbohydrate content of 71.4%DW under -N cultivation achieved under 210°C-3h was 14% higher than that in NaNO3. HTC-algal cultivation strategy under -N mode could save 60% of conventional N. Copyright © 2016 Elsevier Ltd. All rights reserved.

High-level conversion of L-lysine into 5-aminovalerate that can be used for nylon 6,5 synthesis.

PubMed

Park, Si Jae; Oh, Young Hoon; Noh, Won; Kim, Hye Young; Shin, Jae Ho; Lee, Eun Gyo; Lee, Seungwoon; David, Yokimiko; Baylon, Mary Grace; Song, Bong Keun; Jegal, Jonggeon; Lee, Sang Yup; Lee, Seung Hwan

2014-10-01

L-Lysine is a potential feedstock for the production of bio-based precursors for engineering plastics. In this study, we developed a microbial process for high-level conversion of L-lysine into 5-aminovalerate (5AVA) that can be used as a monomer in nylon 6,5 synthesis. Recombinant Escherichia coli WL3110 strain expressing Pseudomonas putida delta-aminovaleramidase (DavA) and lysine 2-monooxygenase (DavB) was grown to high density in fed-batch culture and used as a whole cell catalyst. High-density E. coli WL3110 expressing DavAB, grown to an optical density at 600 nm (OD600 ) of 30, yielded 36.51 g/L 5AVA from 60 g/L L-lysine in 24 h. Doubling the cell density of E. coli WL3110 improved the conversion yield to 47.96 g/L 5AVA from 60 g/L of L-lysine in 24 h. 5AVA production was further improved by doubling the L-lysine concentration from 60 to 120 g/L. The highest 5AVA titer (90.59 g/L; molar yield 0.942) was obtained from 120 g/L L-lysine by E. coli WL3110 cells grown to OD600 of 60. Finally, nylon 6,5 was synthesized by bulk polymerization of ϵ-caprolactam and δ-valerolactam prepared from microbially synthesized 5AVA. The hybrid system demonstrated here has promising possibilities for application in the development of industrial bio-nylon production processes. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

High-yield hydrogen production from biomass by in vitro metabolic engineering: Mixed sugars coutilization and kinetic modeling.

PubMed

Rollin, Joseph A; Martin del Campo, Julia; Myung, Suwan; Sun, Fangfang; You, Chun; Bakovic, Allison; Castro, Roberto; Chandrayan, Sanjeev K; Wu, Chang-Hao; Adams, Michael W W; Senger, Ryan S; Zhang, Y-H Percival

2015-04-21

The use of hydrogen (H2) as a fuel offers enhanced energy conversion efficiency and tremendous potential to decrease greenhouse gas emissions, but producing it in a distributed, carbon-neutral, low-cost manner requires new technologies. Herein we demonstrate the complete conversion of glucose and xylose from plant biomass to H2 and CO2 based on an in vitro synthetic enzymatic pathway. Glucose and xylose were simultaneously converted to H2 with a yield of two H2 per carbon, the maximum possible yield. Parameters of a nonlinear kinetic model were fitted with experimental data using a genetic algorithm, and a global sensitivity analysis was used to identify the enzymes that have the greatest impact on reaction rate and yield. After optimizing enzyme loadings using this model, volumetric H2 productivity was increased 3-fold to 32 mmol H2⋅L(-1)⋅h(-1). The productivity was further enhanced to 54 mmol H2⋅L(-1)⋅h(-1) by increasing reaction temperature, substrate, and enzyme concentrations--an increase of 67-fold compared with the initial studies using this method. The production of hydrogen from locally produced biomass is a promising means to achieve global green energy production.

High-yield hydrogen production from biomass by in vitro metabolic engineering: Mixed sugars coutilization and kinetic modeling

DOE PAGES

Rollin, Joseph A.; Martin del Campo, Julia; Myung, Suwan; ...

2015-04-06

The use of hydrogen (H 2) as a fuel offers enhanced energy conversion efficiency and tremendous potential to decrease greenhouse gas emissions, but producing it in a distributed, carbon-neutral, low-cost manner requires new technologies. Herein we demonstrate the complete conversion of glucose and xylose from plant biomass to H 2 and CO 2 based on an in vitro synthetic enzymatic pathway. Glucose and xylose were simultaneously converted to H 2 with a yield of two H 2 per carbon, the maximum possible yield. Parameters of a nonlinear kinetic model were fitted with experimental data using a genetic algorithm, and amore » global sensitivity analysis was used to identify the enzymes that have the greatest impact on reaction rate and yield. After optimizing enzyme loadings using this model, volumetric H 2 productivity was increased 3-fold to 32 mmol H 2∙L ₋1∙h ₋1. The productivity was further enhanced to 54 mmol H 2∙L ₋1∙h ₋1 by increasing reaction temperature, substrate, and enzyme concentrations—an increase of 67-fold compared with the initial studies using this method. The production of hydrogen from locally produced biomass is a promising means to achieve global green energy production.« less

Optimisation of Microwave-Assisted Extraction of Pomegranate (Punica granatum L.) Seed Oil and Evaluation 
of Its Physicochemical and Bioactive Properties.

PubMed

Çavdar, Hasene Keskin; Yanık, Derya Koçak; Gök, Uğur; Göğüş, Fahrettin

2017-03-01

Pomegranate seed oil was extracted in a closed-vessel high-pressure microwave system. The characteristics of the obtained oil, such as fatty acid composition, free fatty acidity, total phenolic content, antioxidant activity and colour, were compared to those of the oil obtained by cold solvent extraction. Response surface methodology was applied to optimise extraction conditions: power (176-300 W), time (5-20 min), particle size ( d =0.125-0.800 mm) and solvent to sample ratio (2:1, 6:1 and 10:1, by mass). The predicted highest extraction yield (35.19%) was obtained using microwave power of 220 W, particle size in the range of d =0.125-0.450 mm and solvent-to-sample ratio of 10:1 (by mass) in 5 min extraction time. Microwave-assisted solvent extraction (MASE) resulted in higher extraction yield than that of Soxhlet (34.70% in 8 h) or cold (17.50% in 8 h) extraction. The dominant fatty acid of pomegranate seed oil was punicic acid (86%) irrespective of the extraction method. Oil obtained by MASE had better physicochemical properties, total phenolic content and antioxidant activity than the oil obtained by cold solvent extraction.

Cloning, expression and characterization of a new ι-carrageenase from marine bacterium, Cellulophaga sp.

PubMed

Ma, Su; Tan, Yu-Long; Yu, Wen-Gong; Han, Feng

2013-10-01

The purpose of this study is to report a ι-carrageenase which degrades ι-carrageenan yielding neo-ι-carratetraose as the main product in the absence of NaCl. The gene for a new ι-carrageenase, CgiB_Ce, from Cellulophaga sp. QY3 was cloned and sequenced. It comprised an ORF of 1,386 bp encoding for a protein of 461 amino acid residues. From its sequence analysis, CgiB_Ce is a new member of GH family 82 and shared the highest identity of 32% in amino acids with ι-carrageenase CgiA2 from Zobellia galactanovorans indicating that it is a hitherto uncharacterized protein. The recombinant CgiB_Ce had maximum specific activity (1,870 U/mg) at 45 °C and pH 6.5. It was stable between pH 6.0-9.6 and below 40 °C. Although its activity was enhanced by NaCl, the enzyme was active in the absence of NaCl. CgiB_Ce is an endo-type ι-carrageenase that hydrolyzes β-1,4-linkages of ι-carrageenan, yielding neo-ι-carratetraose as the main product (more than 80% of the total product).

Peroxisomal fatty acid oxidation as detected by H2O2 production in intact perfused rat liver.

PubMed Central

Foerster, E C; Fährenkemper, T; Rabe, U; Graf, P; Sies, H

1981-01-01

1. H2O2 formation associated with the metabolism of added fatty acids was quantitatively determined in isolated haemoglobin-free perfused rat liver (non-recirculating system) by two different methods. 2. Organ spectrophotometry of catalase Compound I [Sies & Chance (1970) FEBS Lett. 11, 172-176] was used to detect H2O2 formation (a) by steady-state titration with added hydrogen donor, methanol or (b) by comparison of fatty-acid responses with those of the calibration compound, urate. 3. In the use of the peroxidatic reaction of catalase, [14C]methanol was added as hydrogen donor at an optimal concentration of 1 mM in the presence of 0.2 mM-L-methionine, and 14CO2 production rates were determined. 4. Results obtained by the different methods were similar. 5. The yield of H2O2 formation, expressed as the rate of H2O2 formation in relation to the rate of fatty-acid supply, was less than 1.0 in all cases, indicating that, regardless of chain length, less than one acetyl unit was formed per mol of added fatty acid by the peroxisomal system. In particular, the standard substrate used with isolated peroxisomal preparations (C16:0 fatty acid) gave low yield (close to zero). Long-chain monounsaturated fatty acids exhibit a relatively high yield of H2O2 formation. 6. The hypolipidaemic agent bezafibrate led to slightly increased yields for most of the acids tested, but the yield with oleate was decreased to one-half the original yield. 7. It is concluded that in the intact isolated perfused rat liver the assayable capacity for peroxisomal beta-oxidation is used to only a minor degree. However, the observed rates of H2O2 production with fatty acids can account for a considerable share of the endogenous H2O2 production found in the intact animal. PMID:7317011

Influence of cooling rates and addition of Equex pasta on cooled and frozen-thawed semen of generic gray (Canis lupus) and Mexican gray wolves (C. l. baileyi).

PubMed

Zindl, C; Asa, C S; Günzel-Apel, A-R

2006-10-01

A current priority for the preservation of the endangered Mexican gray wolf (Canis lupus baileyi) is the development of a sperm-based genome resource bank for subsequent use in artificial insemination. To optimize the quality of cryopreserved sperm, the procedures involved in processing semen before and during freezing need to be improved. The aim of this study were to examine the effects of: (i) different cooling periods before freezing and (ii) addition of Equex pasta (Minitüb, Tübingen, Germany) on the characteristics of sperm from the generic gray wolf and the Mexican gray wolf after cooling and cryopreservation. For Mexican wolf sperm, cooling for 0.5 and 1.0 h had a less detrimental effect on cell morphology than cooling for 2.5 h, whereas the slower cooling rate (2.5 h) had a less detrimental effect on functional parameters and seemed to cause less damage to plasma membrane and acrosome integrity than 0.5 and 1.0 h. For the generic gray wolf, cooling semen for 2.5 h had less detrimental effect on plasma membrane integrity and viability; together with the 0.5 h cooling time, it yielded the highest percentages of intact acrosomes. As previously shown in the domestic dog, Equex pasta had no beneficial effect on sperm characteristics in either wolf species.

Influence of pretreatment with Fenton's reagent on biogas production and methane yield from lignocellulosic biomass.

PubMed

Michalska, Karina; Miazek, Krystian; Krzystek, Liliana; Ledakowicz, Stanisław

2012-09-01

Biomass from Miscanthus giganteus, Sida hermaphrodita and Sorghum Moensch was treated with Fenton's reagent for 2 hours under optimal conditions (pH=3, mass ratio of [Fe(2+)]:[H(2)O(2)] equals 1:25 for Miscanthus and Sorghum and 1:15 for Sida). The degrees of delignification were 30.3%, 62.3% and 48.1% for the three plant species, respectively. The volatile fatty acids concentration after chemical pretreatment was high enough for production of biogas with a high methane content. Combined chemical oxidation and enzymatic hydrolysis with cellulase and cellobiase led to glucose contents of above 4 g/L. Among the tested plants, the highest biogas production (25.2 Ndm(3)/kg TS fed) with a 75% methane content was obtained with Sorghum Moensch. The results of the three-step process of biomass degradation show the necessity of applying a chemical pretreatment such as oxidation with Fenton's reagent. Moreover, the coagulation of residual Fe(3+) ions is not required for high biogas production. Copyright © 2012 Elsevier Ltd. All rights reserved.

Optimization of pH and nitrogen for enhanced hydrogen production by Synechocystis sp. PCC 6803 via statistical and machine learning methods.

PubMed

Burrows, Elizabeth H; Wong, Weng-Keen; Fern, Xiaoli; Chaplen, Frank W R; Ely, Roger L

2009-01-01

The nitrogen (N) concentration and pH of culture media were optimized for increased fermentative hydrogen (H(2)) production from the cyanobacterium, Synechocystis sp. PCC 6803. The optimization was conducted using two procedures, response surface methodology (RSM), which is commonly used, and a memory-based machine learning algorithm, Q2, which has not been used previously in biotechnology applications. Both RSM and Q2 were successful in predicting optimum conditions that yielded higher H(2) than the media reported by Burrows et al., Int J Hydrogen Energy. 2008;33:6092-6099 optimized for N, S, and C (called EHB-1 media hereafter), which itself yielded almost 150 times more H(2) than Synechocystis sp. PCC 6803 grown on sulfur-free BG-11 media. RSM predicted an optimum N concentration of 0.63 mM and pH of 7.77, which yielded 1.70 times more H(2) than EHB-1 media when normalized to chlorophyll concentration (0.68 +/- 0.43 micromol H(2) mg Chl(-1) h(-1)) and 1.35 times more when normalized to optical density (1.62 +/- 0.09 nmol H(2) OD(730) (-1) h(-1)). Q2 predicted an optimum of 0.36 mM N and pH of 7.88, which yielded 1.94 and 1.27 times more H(2) than EHB-1 media when normalized to chlorophyll concentration (0.77 +/- 0.44 micromol H(2) mg Chl(-1) h(-1)) and optical density (1.53 +/- 0.07 nmol H(2) OD(730) (-1) h(-1)), respectively. Both optimization methods have unique benefits and drawbacks that are identified and discussed in this study. (c) 2009 American Institute of Chemical Engineers Biotechnol. Prog., 2009.

Selective nickel-catalyzed conversion of model and lignin-derived phenolic compounds to cyclohexanone-based polymer building blocks.

PubMed

Schutyser, Wouter; Van den Bosch, Sander; Dijkmans, Jan; Turner, Stuart; Meledina, Maria; Van Tendeloo, Gustaaf; Debecker, Damien P; Sels, Bert F

2015-05-22

Valorization of lignin is essential for the economics of future lignocellulosic biorefineries. Lignin is converted into novel polymer building blocks through four steps: catalytic hydroprocessing of softwood to form 4-alkylguaiacols, their conversion into 4-alkylcyclohexanols, followed by dehydrogenation to form cyclohexanones, and Baeyer-Villiger oxidation to give caprolactones. The formation of alkylated cyclohexanols is one of the most difficult steps in the series. A liquid-phase process in the presence of nickel on CeO2 or ZrO2 catalysts is demonstrated herein to give the highest cyclohexanol yields. The catalytic reaction with 4-alkylguaiacols follows two parallel pathways with comparable rates: 1) ring hydrogenation with the formation of the corresponding alkylated 2-methoxycyclohexanol, and 2) demethoxylation to form 4-alkylphenol. Although subsequent phenol to cyclohexanol conversion is fast, the rate is limited for the removal of the methoxy group from 2-methoxycyclohexanol. Overall, this last reaction is the rate-limiting step and requires a sufficient temperature (>250 °C) to overcome the energy barrier. Substrate reactivity (with respect to the type of alkyl chain) and details of the catalyst properties (nickel loading and nickel particle size) on the reaction rates are reported in detail for the Ni/CeO2 catalyst. The best Ni/CeO2 catalyst reaches 4-alkylcyclohexanol yields over 80 %, is even able to convert real softwood-derived guaiacol mixtures and can be reused in subsequent experiments. A proof of principle of the projected cascade conversion of lignocellulose feedstock entirely into caprolactone is demonstrated by using Cu/ZrO2 for the dehydrogenation step to produce the resultant cyclohexanones (≈80 %) and tin-containing beta zeolite to form 4-alkyl-ε-caprolactones in high yields, according to a Baeyer-Villiger-type oxidation with H2 O2 . © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Deviation between the chemistry of Ce(IV) and Pu(IV) and routes to ordered and disordered heterobimetallic 4f/5f and 5f/5f phosphonates.

PubMed

Diwu, Juan; Wang, Shuao; Good, Justin J; DiStefano, Victoria H; Albrecht-Schmitt, Thomas E

2011-06-06

The heterobimetallic actinide compound UO(2)Ce(H(2)O)[C(6)H(4)(PO(3)H)(2)](2)·H(2)O was prepared via the hydrothermal reaction of U(VI) and Ce(IV) in the presence of 1,2-phenylenediphosphonic acid. We demonstrate that this is a kinetic product that is not stable with respect to decomposition to the monometallic compounds. Similar reactions have been explored with U(VI) and Ce(III), resulting in the oxidation of Ce(III) to Ce(IV) and the formation of the Ce(IV) phosphonate, Ce[C(6)H(4)(PO(3)H)(PO(3)H(2))][C(6)H(4)(PO(3)H)(PO(3))]·2H(2)O, UO(2)Ce(H(2)O)[C(6)H(4)(PO(3)H)(2)](2)·H(2)O, and UO(2)[C(6)H(4)(PO(3)H)(2)](H(2)O)·H(2)O. In comparison, the reaction of U(VI) with Np(VI) only yields Np[C(6)H(4)(PO(3)H)(2)](2)·2H(2)O and aqueous U(VI), whereas the reaction of U(VI) with Pu(VI) yields the disordered U(VI)/Pu(VI) compound, (U(0.9)Pu(0.1))O(2)[C(6)H(4)(PO(3)H)(2)](H(2)O)·H(2)O, and the Pu(IV) phosphonate, Pu[C(6)H(4)(PO(3)H)(PO(3)H(2))][C(6)H(4)(PO(3)H)(PO(3))]·2H(2)O. The reactions of Ce(IV) with Np(VI) yield disordered heterobimetallic phosphonates with both M[C(6)H(4)(PO(3)H)(PO(3)H(2))][C(6)H(4)(PO(3)H)(PO(3))]·2H(2)O (M = Ce, Np) and M[C(6)H(4)(PO(3)H)(2)](2)·2H(2)O (M = Ce, Np) structures, as well as the Ce(IV) phosphonate Ce[C(6)H(4)(PO(3)H)(PO(3)H(2))][C(6)H(4)(PO(3)H)(PO(3))]·2H(2)O. Ce(IV) reacts with Pu(IV) to yield the Pu(VI) compound, PuO(2)[C(6)H(4)(PO(3)H)(2)](H(2)O)·3H(2)O, and a disordered heterobimetallic Pu(IV)/Ce(IV) compound with the M[C(6)H(4)(PO(3)H)(PO(3)H(2))][C(6)H(4)(PO(3)H)(PO(3))]·2H(2)O (M = Ce, Pu) structure. Mixtures of Np(VI) and Pu(VI) yield disordered heterobimetallic Np(IV)/Pu(IV) phosphonates with both the An[C(6)H(4)(PO(3)H)(PO(3)H(2))][C(6)H(4)(PO(3)H)(PO(3))]·2H(2)O (M = Np, Pu) and An[C(6)H(4)(PO(3)H)(2)](2)·2H(2)O (M = Np, Pu) formulas. © 2011 American Chemical Society

Electron-stimulated desorption study of hydrogen-exposed aluminum films

NASA Technical Reports Server (NTRS)

Park, CH.; Bujor, M.; Poppa, H.

1984-01-01

H2 adsorption of evaporated clean and H2-exposed aluminum films is investigated by using the electron-stimulated desorption (ESD) method. A strong H(+)ESD signal is observed on a freshly evaporated aluminum surface which is clean according to previously proposed cleanlines criteria. An increased H(+) yield on H2 exposure is also observed. However, the increasing rate of H(+) emission could be directly correlated with small increases in H2O partial pressure during H2 exposure. It is proposed that the oxidation of aluminum by water vapor and subsequent adsorption of H2 or water is the primary process of the enhanced high H(+) yield during H2 exposure.

Strongly lensed neutral hydrogen emission: detection predictions with current and future radio interferometers

NASA Astrophysics Data System (ADS)

Deane, R. P.; Obreschkow, D.; Heywood, I.

2015-09-01

Strong gravitational lensing provides some of the deepest views of the Universe, enabling studies of high-redshift galaxies only possible with next-generation facilities without the lensing phenomenon. To date, 21-cm radio emission from neutral hydrogen has only been detected directly out to z ˜ 0.2, limited by the sensitivity and instantaneous bandwidth of current radio telescopes. We discuss how current and future radio interferometers such as the Square Kilometre Array (SKA) will detect lensed H I emission in individual galaxies at high redshift. Our calculations rely on a semi-analytic galaxy simulation with realistic H I discs (by size, density profile and rotation), in a cosmological context, combined with general relativistic ray tracing. Wide-field, blind H I surveys with the SKA are predicted to be efficient at discovering lensed H I systems, increasingly so at z ≳ 2. This will be enabled by the combination of the magnification boosts, the steepness of the H I luminosity function at the high-mass end, and the fact that the H I spectral line is relatively isolated in frequency. These surveys will simultaneously provide a new technique for foreground lens selection and yield the highest redshift H I emission detections. More near term (and existing) cm-wave facilities will push the high-redshift H I envelope through targeted surveys of known lenses.

Neural network-based brain tissue segmentation in MR images using extracted features from intraframe coding in H.264

NASA Astrophysics Data System (ADS)

Jafari, Mehdi; Kasaei, Shohreh

2012-01-01

Automatic brain tissue segmentation is a crucial task in diagnosis and treatment of medical images. This paper presents a new algorithm to segment different brain tissues, such as white matter (WM), gray matter (GM), cerebral spinal fluid (CSF), background (BKG), and tumor tissues. The proposed technique uses the modified intraframe coding yielded from H.264/(AVC), for feature extraction. Extracted features are then imposed to an artificial back propagation neural network (BPN) classifier to assign each block to its appropriate class. Since the newest coding standard, H.264/AVC, has the highest compression ratio, it decreases the dimension of extracted features and thus yields to a more accurate classifier with low computational complexity. The performance of the BPN classifier is evaluated using the classification accuracy and computational complexity terms. The results show that the proposed technique is more robust and effective with low computational complexity compared to other recent works.

Neural network-based brain tissue segmentation in MR images using extracted features from intraframe coding in H.264

NASA Astrophysics Data System (ADS)

Jafari, Mehdi; Kasaei, Shohreh

2011-12-01

Automatic brain tissue segmentation is a crucial task in diagnosis and treatment of medical images. This paper presents a new algorithm to segment different brain tissues, such as white matter (WM), gray matter (GM), cerebral spinal fluid (CSF), background (BKG), and tumor tissues. The proposed technique uses the modified intraframe coding yielded from H.264/(AVC), for feature extraction. Extracted features are then imposed to an artificial back propagation neural network (BPN) classifier to assign each block to its appropriate class. Since the newest coding standard, H.264/AVC, has the highest compression ratio, it decreases the dimension of extracted features and thus yields to a more accurate classifier with low computational complexity. The performance of the BPN classifier is evaluated using the classification accuracy and computational complexity terms. The results show that the proposed technique is more robust and effective with low computational complexity compared to other recent works.

Interrelationships of somatic cell count, mastitis, and milk yield in a low somatic cell count herd.

PubMed

Deluyker, H A; Gay, J M; Weaver, L D

1993-11-01

In a high yielding low SCC herd, changes in milk yield associated with SCC and occurrence of clinical mastitis and differences in SCC with parity, clinical mastitis, and DIM were investigated. Milk yield data were obtained at every milking, and SCC was measured once every 48 h in 117 cows during the first 119 d postpartum. Effects of SCC and clinical mastitis on cumulative milk yield in the first 119 d postpartum were evaluated with least squares linear regression. Repeated measures ANOVA was used to detect changes in SCC. The SCC was highest at lactation onset, and cows with clinical mastitis had significantly higher SCC. During the 10 d prior to onset of clinical mastitis, SCC was higher in affected cows than in matched unaffected controls and surged just prior to diagnosis. During the 10-d period following a mastitis treatment, SCC differences between treated and control cows remained significant but became smaller with time and returned to the premastitis differences. Occurrence of clinical mastitis was associated with 5% milk yield loss. Cows with mean SCC > 245,000 cells/ml over the 119 d showed 6.2% yield loss compared with cows with SCC < or = 90,000 cells/ml. Cows with clinical mastitis had higher SCC prior to and following the end of treatment for mastitis than did controls. Clinical mastitis and SCC were associated with significant yield loss. Milk yield loss attributed to clinical mastitis was greater than that associated with elevated SCC (> 245,000 cells/ml) because a greater percentage of cows (26%) had clinical mastitis than elevated SCC (12.5%).

Synthesis of high-quality diesel with furfural and 2-methylfuran from hemicellulose.

PubMed

Li, Guangyi; Li, Ning; Wang, Zhiqiang; Li, Changzhi; Wang, Aiqin; Wang, Xiaodong; Cong, Yu; Zhang, Tao

2012-10-01

Hydroxyalkylation-alkylation (HAA) coupled with hydrodeoxygenation is a promising route for the synthesis of renewable high-quality diesel or jet fuel. In this work, a series of solid-acid catalysts were firstly used for HAA between lignocellulose-derived furan and carbonyl compounds. Among the investigated catalysts, Nafion-212 resin demonstrated the highest activity and stability. Owing to the high activity of the reactants and the advantage in industrial integration, the HAA of 2-methylfuran (2-MF) and furfural can be considered as a prospective route in future applications. Catalyst loading, reaction temperature, and time had evident effects on the HAA of 2-MF and furfural over Nafion-212 resin. Finally, the HAA product of 2-MF and furfural was hydrogenated over a Pd/C catalyst and hydrodeoxygenated over Pt-loaded solid-acid catalysts. Pt/zirconium phosphate (Pt/ZrP) was found to be the best catalyst for hydrodeoxygenation. Over the 4 % Pt/ZrP catalyst, a 94 % carbon yield of diesel and 75 % carbon yield of C15 hydrocarbons (with 6-butylundecane as the major component) was achieved. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Polymer-assisted iron oxide magnetic nanoparticle immobilized keratinase

NASA Astrophysics Data System (ADS)

Konwarh, Rocktotpal; Karak, Niranjan; Rai, Sudhir Kumar; Mukherjee, Ashis Kumar

2009-06-01

Nanotechnology holds the prospect for avant-garde changes to improve the performance of materials in various sectors. The domain of enzyme biotechnology is no exception. Immobilization of industrially important enzymes onto nanomaterials, with improved performance, would pave the way to myriad application-based commercialization. Keratinase produced by Bacillus subtilis was immobilized onto poly(ethylene glycol)-supported Fe3O4 superparamagnetic nanoparticles. The optimization process showed that the highest enzyme activity was noted when immobilized onto cyanamide-activated PEG-assisted MNP prepared under conditions of 25 °C and pH 7.2 of the reaction mixture before addition of H2O2 (3% w/w), 2% (w/v) PEG6000 and 0.062:1 molar ratio of PEG to FeCl2·4H2O. Further statistical optimization using response surface methodology yielded an R2 value that could explain more than 94% of the sample variations. Along with the magnetization studies, the immobilization of the enzyme onto the PEG-assisted MNP was characterized by UV, XRD, FTIR and TEM. The immobilization process had resulted in an almost fourfold increase in the enzyme activity over the free enzyme. Furthermore, the immobilized enzyme exhibited a significant thermostability, storage stability and recyclability. The leather-industry-oriented application of the immobilized enzyme was tested for the dehairing of goat-skin.

Isomerization of 7-oxabenzonorbornadienes into naphthols catalyzed by [RuCl(2)(CO)(3)](2).

PubMed

Ballantine, Melissa; Menard, Michelle L; Tam, William

2009-10-02

Ruthenium-catalyzed isomerization of 7-oxanorbornadienes into naphthols was investigated. Among the various ruthenium catalysts tested, [RuCl(2)(CO)(3)](2) gave the highest yields in the isomerization, and various substituted naphthols were synthesized in moderate to excellent yields. Both symmetrical and unsymmetrical 7-oxanorbornadienes were employed in the study, and moderate to excellent regioselectivities were observed.

Preparation of 7-hydroxy-2-oxoindolin-3-ylacetic acid and its [13C2], [5-n-3H], and [5-n-3H]-7-O-glucosyl analogues for use in the study of indol-3-ylacetic acid catabolism

NASA Technical Reports Server (NTRS)

Lewer, P.; Bandurski, R. S. (Principal Investigator)

1987-01-01

An improved synthesis of 7-hydroxy-2-oxoindolin-3-ylacetic acid via the base-induced condensation reaction between oxalate esters and 7-benzyloxyindolin-2-one is described. 7-Benzyloxyindolin-2-one was prepared in four steps and 50% overall yield from 3-hydroxy-2-nitrotoluene. The yield of the title compound from 7-benzyloxyindolin-2-one was 56%. This route was used to prepare 7-hydroxy-2-oxoindolin-3-yl[13C2]acetic acid in 30% yield from [13C2]oxalic acid dihydrate. The method could not be extended to the preparation of the corresponding [14C2]-compound. However, an enzyme preparation from Zea mays roots catalysed the conversion of carrier-free [5-n-3H]indol-3-ylacetic acid with a specific activity of 16.7 Ci mmol-1 to a mixture of 7-hydroxy-2-oxo[5-n-3H]indolin-3-ylacetic acid and its [5-n-3H]-7-O-glucoside in ca. 3 and 40% radiochemical yield respectively. The glucoside was converted into the 7-hydroxy compound in 80% yield by means of beta-glucosidase.

Quantitative trait loci for yield and grain plumpness relative to maturity in three populations of barley (Hordeum vulgare L.) grown in a low rain-fall environment

PubMed Central

Obsa, Bulti Tesso; Eglinton, Jason; Coventry, Stewart; March, Timothy; Guillaume, Maxime; Le, Thanh Phuoc; Hayden, Matthew; Langridge, Peter

2017-01-01

Identifying yield and grain plumpness QTL that are independent of developmental variation or phenology is of paramount importance for developing widely adapted and stable varieties through the application of marker assisted selection. The current study was designed to dissect the genetic basis of yield performance and grain plumpness in southern Australia using three doubled haploid (DH) populations developed from crosses between adapted parents that are similar in maturity and overall plant development. Three interconnected genetic populations, Commander x Fleet (CF), Commander x WI4304 (CW), and Fleet x WI4304 (FW) developed from crossing of Australian elite barley genotypes, were used to map QTL controlling yield and grain plumpness. QTL for grain plumpness and yield were analysed using genetic linkage maps made of genotyping-by-sequencing markers and major phenology genes, and field trials at three drought prone environments for two growing seasons. Seventeen QTL were detected for grain plumpness. Eighteen yield QTL explaining from 1.2% to 25.0% of the phenotypic variation were found across populations and environments. Significant QTL x environment interaction was observed for all grain plumpness and yield QTL, except QPlum.FW-4H.1 and QYld.FW-2H.1. Unlike previous yield QTL studies in barley, none of the major developmental genes, including Ppd-H1, Vrn-H1, Vrn-H2 and Vrn-H3, that drive barley adaption significantly affected grain plumpness and yield here. Twenty-two QTL controlled yield or grain plumpness independently of known maturity QTL or genes. Adjustment for maturity effects through co-variance analysis had no major effect on these yield QTL indicating that they control yield per se. PMID:28542571

Quantitative trait loci for yield and grain plumpness relative to maturity in three populations of barley (Hordeum vulgare L.) grown in a low rain-fall environment.

PubMed

Obsa, Bulti Tesso; Eglinton, Jason; Coventry, Stewart; March, Timothy; Guillaume, Maxime; Le, Thanh Phuoc; Hayden, Matthew; Langridge, Peter; Fleury, Delphine

2017-01-01

Identifying yield and grain plumpness QTL that are independent of developmental variation or phenology is of paramount importance for developing widely adapted and stable varieties through the application of marker assisted selection. The current study was designed to dissect the genetic basis of yield performance and grain plumpness in southern Australia using three doubled haploid (DH) populations developed from crosses between adapted parents that are similar in maturity and overall plant development. Three interconnected genetic populations, Commander x Fleet (CF), Commander x WI4304 (CW), and Fleet x WI4304 (FW) developed from crossing of Australian elite barley genotypes, were used to map QTL controlling yield and grain plumpness. QTL for grain plumpness and yield were analysed using genetic linkage maps made of genotyping-by-sequencing markers and major phenology genes, and field trials at three drought prone environments for two growing seasons. Seventeen QTL were detected for grain plumpness. Eighteen yield QTL explaining from 1.2% to 25.0% of the phenotypic variation were found across populations and environments. Significant QTL x environment interaction was observed for all grain plumpness and yield QTL, except QPlum.FW-4H.1 and QYld.FW-2H.1. Unlike previous yield QTL studies in barley, none of the major developmental genes, including Ppd-H1, Vrn-H1, Vrn-H2 and Vrn-H3, that drive barley adaption significantly affected grain plumpness and yield here. Twenty-two QTL controlled yield or grain plumpness independently of known maturity QTL or genes. Adjustment for maturity effects through co-variance analysis had no major effect on these yield QTL indicating that they control yield per se.

Integrated production of lactic acid and biomass on distillery stillage.

PubMed

Djukić-Vuković, Aleksandra P; Mojović, Ljiljana V; Vukašinović-Sekulić, Maja S; Nikolić, Svetlana B; Pejin, Jelena D

2013-09-01

The possibilities of parallel lactic acid and biomass production in batch and fed-batch fermentation on distillery stillage from bioethanol production were studied. The highest lactic acid yield and productivity of 92.3 % and 1.49 g L(-1) h(-1) were achieved in batch fermentation with initial sugar concentration of 55 g L(-1). A significant improvement of the process was achieved in fed-batch fermentation where the concentration of lactic acid was increased to 47.6 % and volumetric productivity for 21 % over the batch process. A high number of Lactobacillus rhamnosus ATCC 7469 viable cells of 10(9) CFU ml(-1) was attained at the end of fed-batch fermentation. The survival of 92.9 % of L. rhamnosus cells after 3 h of incubation at pH 2.5 validated that the fermentation media remained after lactic acid removal could be used as a biomass-enriched animal feed thus making an additional value to the process.

Water absorption and moisture permeation properties of chitosan/poly(acrylamide-co-itaconic acid) IPC films.

PubMed

Bajpai, M; Bajpai, S K; Jyotishi, Pooja

2016-03-01

In this work, aqueous solutions of chitosan (Ch) and [poly(acrylamide(AAm)-co-itaconicacid(IA)] have been mixed to yield Ch/poly(AAm-co-IA) Inter-polyelectrolyte complex (IPC) films. The films were characterized by FTIR, X-ray diffraction (XRD) and thermo gravimetric analysis (TGA). There was remarkable increase in the crystalline nature of IPC films. The films were investigated for their water absorption capacity in the physiological fluid (PF) of pH 7.4 at 37 °C. The amount of IA present in the film forming solutions affected the water absorption behavior of the resulting films. The dynamic water uptake data were interpreted by various kinetic models. The effect of pH on the swelling ratio (SR) indicated that the films showed highest swelling in lower as well as higher pH media. The water vapor transmission rates (WVTR) were obtained in the range of 6000-6645 g/m(2)/day. Copyright © 2015 Elsevier B.V. All rights reserved.

Exploring the limits of crop productivity: beyond the limits of tipburn in lettuce

NASA Technical Reports Server (NTRS)

Frantz, Jonathan M.; Ritchie, Glen; Cometti, Nilton N.; Robinson, Justin; Bugbee, Bruce

2004-01-01

The productivity of lettuce in a combination of high light, high temperature, and elevated CO2 has not been commonly studied because rapid growth usually causes a calcium deficiency in meristems called tipburn, which greatly reduces quality and marketability. We eliminated tipburn by blowing air directly onto the meristem, which allowed us to increase the photosynthetic photon flux (PPF) to 1000 micromoles m-2 s-1 (57.6 mol m-2 d-1); two to three times higher than normally used for lettuce. Eliminating tipburn doubled edible yield at the highest PPF level. In addition to high PPF, CO2 was elevated to 1200 micromoles m-2 mol-1, which increased the temperature optimum from 25 to 30 degrees C. The higher temperature increased leaf expansion rate, which improved radiation capture and more than doubled yield. Photosynthetic efficiency, measured as canopy quantum yield in a whole-plant gas exchange system, steadily increased up to the highest temperature of 32 degrees C in high CO2. The highest productivity was 19 g m-2 d-1 of dry biomass (380 g d-1 fresh mass) averaged over the 23 days the plants received light. Without the limitation of tipburn, the combination of high PPF, high temperature, and elevated CO2 resulted in a 4-fold increase in growth rate over productivity in conventional environments.

Relation of Land Use to Streamflow and Water Quality at Selected Sites in the City of Charlotte and Mecklenburg County, North Carolina, 1993-98

USGS Publications Warehouse

Bales, Jerad D.; Weaver, J. Curtis; Robinson, Jerald B.

1999-01-01

Streamflow and water-quality data were collected at nine sites in the city of Charlotte and Mecklenburg County, North Carolina, during 1993–97. Six of the basins drained areas having relatively homogeneous land use and were less than 0.3 square mile in size; the other three basins had mixed land use. Atmospheric wet-deposition data were collected in three of the basins during 1997–98.Streamflow yield varied by a factor of six among the sites, despite the fact that sites were in close proximity to one another. The lowest yield occurred in a residential basin having no curbs and gutters. The variability in mean flow from these small, relatively homogeneous basins is much greater than is found in streams draining basins that are 10 square miles in size or larger. The ratio of runoff to rainfall in the developing basin appears to have increased during the study period.Low-flow suspended-sediment concentrations in the study basins were about the same magnitude as median stormflow concentrations in Piedmont agricultural basins. Sediment concentrations were higher in the mixed land-use basins and in the developing basin. Median suspended-sediment concentrations in these basins generally were an order of magnitude greater than median concentrations in the other five basins, which had stable land use.Some of the highest total nitrogen concentrations occurred in residential basins. Total nitrogen concentrations detected in this study were about twice as high as concentrations in small Piedmont streams affected by agriculture and urbanization. Most of the total nitrogen consisted of organic nitrogen at all of the sites except in two residential land- use basins. The high ammonia content of lawn fertilizer may explain the higher ammonia concentration in stormflow from residential basins.The two basins with the highest median suspended-sediment concentrations also had the highest total phosphorus concentrations. Median total phosphorus concentrations measured in this study were several times greater than median concentrations in small Piedmont streams but almost an order of magnitude less than total phosphorus concentrations in Charlotte streams during the late 1970's.Bacteria concentrations are not correlated to streamflow. The highest bacteria levels were found in 'first-flush' samples. Higher fecal coliform concentrations were associated with residential land use.Chromium, copper, lead, and zinc occurred at all sites in concentrations that exceeded the North Carolina ambient water-quality standards. The median chromium concentration in the developing basin was more than double the median concentration at any other site. As with chromium, the maximum copper concentration in the developing basin was almost an order of magnitude greater than maximum concentrations at other sites. The highest zinc concentration also occurred in the developing basin. Samples were analyzed for 121 organic compounds and 57 volatile organic compounds. Forty-five organic compounds and seven volatile organic compounds were detected. At least five compounds were detected at all sites, and 15 or more compounds were detected at all sites except two mixed land-use basins. Atrazine, carbaryl, and metolachlor were detected at eight sites, and 90 percent of all samples had measurable amounts of atrazine. About 60 percent of the samples had detectable levels of carbaryl and metolachlor. Diazinon and malathion were measured in samples from seven sites, and methyl parathion, chlorpyrifos, alachlor, and 2,4-D were detected at four or more sites. The fewest compounds were detected in the larger, mixed land-use basins. Residential basins and the developing basin had the greatest number of detections of organic compounds.The pH of wet atmospheric deposition in three Charlotte basins was more variable than the pH measured at a National Atmospheric Deposition Program (NADP)site in Rowan County. Summer pH values were significantly lower than pH measured during the remainder of the year, probably as a result of poorer air quality and different weather patterns during the summer.Concentrations of ammonia and nitrate at the Charlotte sites generally were lower than those measured at the NADP site. Summer concentrations of ammonia and nitrate at both the Charlotte and the NADP sites were significantly greater than concentrations measured during the remainder of the year, again probably reflecting poorer summertime air-quality conditions.Sediment yields at the nine sites ranged from 77 tons per square mile per year in a residential basin to 4,700 tons per square mile per year at the developing basin. Residential areas that have been built-out for several years and industrial areas appear, in general, to have the lowest sediment yields for the Charlotte study sites.Average annual yields of total nitrogen loads ranged from about 1.7 tons per square mile to 6.6 tons per square mile. Average annual total phosphorus yields for all sites except the developing basin were less than 1.4 tons per square mile. Phosphorus yield at the developing basin was 13 .4 tons per square mile per year.Biochemical oxygen demand loading in 1993 from all of the permitted wastewater-treatment facilities in Charlotte and Mecklenburg County was about 1.5 tons per day or 548 tons per year. Converting this point-source loading to an annual yield for the 528 square-mile area of Mecklenburg County is equivalent to 1.03 tons per square mile per year, or a yield much lower than any of the yields measured at the nine study sites. In other words, biochemical oxygen demand loading from nonpoint sources in Mecklenburg County probably exceeds loading from all point sources by a large amount.Loads and average annual yields were computed for five metals-chromium, copper, lead, nickel, and zinc. The highest annual average yields for all five of these metals were in the developing basin, which also had the highest annual average suspended-sediment yield of all the sites. Estimated wet-deposition watershed loadings suggest that atmospheric deposition may be an important source of some metals, including chromium, copper, lead, and zinc, in Charlotte storm water.Storm water from residential land-use basins has higher concentrations of total nitrogen, fecal coliform bacteria, and organic compounds than do other land-use types. Reductions in suspended-sediment concentrations should generally result in reduced export of phosphorus and metals. Stable land uses, such as industrial areas and built-out residential basins, have lower sediment concentrations in stormwater than do mixed land use and developing basins. Finally, atmospheric deposition may be an important source of nitrogen and some metals in Charlotte stormwater.

Comparative study of alkaline hydrogen peroxide and organosolv pretreatments of sugarcane bagasse to improve the overall sugar yield.

PubMed

Yu, Hailong; You, Yanzhi; Lei, Fuhou; Liu, Zuguang; Zhang, Weiming; Jiang, Jianxin

2015-01-01

Green liquor (GL) combined with H2O2 (GL-H2O2) and green liquor (GL) combined with ethanol (GL-ethanol) were chosen for treating sugarcane bagasse. Results showed that the glucose yield (calculated from the glucose content as a percentage of the theoretical glucose available in the substrates)of sugarcane bagasse from GL-ethanol pretreatment (97.7%) was higher than that from GL-H2O2 pretreatment (41.7%) after 72h hydrolysis with 18 filter paper unit (FPU)/g-cellulose for cellulase, 27,175 cellobiase units (CBU)/g-cellulose for β-glucosidase. Furthermore, about 94.1% of xylan was converted to xylose after GL-ethanol pretreatment without additional xylanase, while the xylose yield was only 29.2% after GL-H2O2 pretreatment. Scanning electron microscopy showed that GL-ethanol pretreatment could break up the fiber severely. Moreover, GL-ethanol pretreated substrate was more accessible to cellulase and more hydrophilic than that of GL-H2O2 pretreated. Therefore, GL-ethanol pretreatment is a promising method for improving the overall sugar (glucose and xylan) yield of sugarcane bagasse. Copyright © 2015 Elsevier Ltd. All rights reserved.

[Anaerobic co-digestion of corn stalk and vermicompost].

PubMed

Chen, Guang-yin; Zheng, Zheng; Zou, Xing-xing; Fang, Cai-xia; Luo, Yan

2010-02-01

The characteristics of corn stalk digested alone at different total solid (TS) loading rates and co-digestion of various proportions of corn stalk and vermicompost were investigated by batch model at 35 degrees C +/- 1 degrees C. The organic loading rates (OLRs) studied were in the range of 1.2%-6.0% TS and increasing proportions of vermicompost from 20% to 80% TS. A maximum methane yield of corn stalk digested alone was 217.60 mL/g obtained at the TS loading rate of 4.8%. However, when the TS loading rate was 6.0%, the anaerobic system was acidified and the lowest pH value was 5.10 obtained on day 4 and the biogas productivity decreased. Furthermore, co-digestion of vermicompost and corn stalk in varying proportions were investigated at constant of 6.0% TS. Co-digestion with vermicompost improved the biodegradability of corn stalk and the methane yield was improved by 4.42%-58.61%, and led to higher pH values, higher volatile fatty acids (VFAs) concentration and lower alkalinity content compared with corn stalk digested alone. The maximum biogas yield and methane yield of 410.30 mL/g and 259. 35 mL/g were obtained for 40% vermicompost and 60% corn stalk respectively. Compared with corn stalk digested alone, co-digested with vermicompost didn' t affect methane content and the fermentation type, but promoted the destruction of crystalline of cellulose and the highest destruction rate was 29.36% for 40% vermicompost and 60% corn stalk. Therefore, adding vermicompost was beneficial for the decomposition and increasing the biotransformation rate of corn stalk.

Comparison of supercritical fluid and Soxhlet extractions for the quantification of hydrocarbons from Euphorbia macroclada.

PubMed

Ozcan, Adnan; Ozcan, Asiye Safa

2004-10-08

This study compares conventional Soxhlet extraction and analytical scale supercritical fluid extraction (SFE) for their yields in extracting of hydrocarbons from arid-land plant Euphorbia macroclada. The plant material was firstly sequentially extracted with supercritical carbon dioxide, modified with 10% methanol (v/v) in the optimum conditions that is a pressure of 400atm and a temperature of 50 degrees C and then it was sonicated in methylene chloride for an additional 4h. E. macroclada was secondly extracted by using a Soxhlet apparatus at 30 degrees C for 8h in methylene chloride. The validated SFE was then compared to the extraction yield of E. macroclada with a Soxhlet extraction by using the Student's t-test at the 95% confidence level. All of extracts were fractionated with silica-gel in a glass column to get better hydrocarbon yields. Thus, the highest hydrocarbons yield from E. macroclada was achieved with SFE (5.8%) when it compared with Soxhlet extractions (1.1%). Gas chromatography (GC) analysis was performed to determine the quantitative hydrocarbons from plant material. The greatest quantitative hydrocarbon recovery from GC was obtained by supercritical carbon dioxide extract (0.6mgg(-1)).

Preparation of Egg White Liquid Hydrolysate (ELH) and Its Radical-Scavenging Activity

PubMed Central

Noh, Dong Ouk; Suh, Hyung Joo

2015-01-01

In the present study, an optimum protease was selected to hydrolyze the egg white liquid protein for the antioxidant peptides. Alcalase treatment yielded the highest amount of α-amino groups (15.27 mg/mL), while the control (no enzymatic hydrolysis) showed the lowest amount of α-amino groups (1.53 mg/mL). Alcalase also gave the highest degree of hydrolysis (DH) value (43.2%) and was more efficient for egg white liquid hydrolysis than the other enzymes. The Alcalase hydrolysate had the highest radical-scavenging activity (82.5%) at a concentration of 5.0 mg/mL. The conditions for enzymatic hydrolysis of egg white liquid with Alcalase were selected as substrate : water ratio of 2:1. Five percent Alacalse treatment did not show significant (P>0.05) increases of DH and α-amino nitrogen content after 24 h-hydrolysis. Thirty two hour-hydrolysis with 5% Alcalase is sufficient to make antioxidative egg white liquid hydrolysate from egg white liquid. DPPH and ABTS radical-scavenging activities were significantly (P<0.05) higher after enzymatic digestion. These results suggest that active peptides released from egg-white protein are effective radical-scavengers. Thus, this approach may be useful for the preparation of potent antioxidant products. PMID:26451355

Critical body-residues for lethal and sublethal effects of sediment-associated PAH on benthic copepods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lotufo, G.R.

1995-12-31

Adult females of the meiobenthic copepod Schizopera knabeni were exposed to sediment-associated fluoranthene for 3, 6, 12, 24, 96, and 240 h. Sediment concentrations ranged from 25 to 1,661 nmol (5--336 {micro}g)/gdw and the TOC was 1.5%. Body burden increased to an apparent steady state after only 6 h. Elimination half-lives were 4.6 and 3.2 h in uncontaminated water and sediment, respectively. Toxic effects were only detected after 240 h as increased mortality and decreased offspring production. Significant mortality was observed only at the highest concentration; the LC50 was 1,011 nmol (204 {micro}g)/dgw. In contrast, offspring production was decreased atmore » much lower concentrations, yielding an IC25 value of 148 nmol (30 {micro}g)/dgw. Lethal critical body residue (CBR) was determined as a 10-d LD50 of 15.5 {micro}mol/g dry tissue. By measuring PAH concentrations in the body and eggs of females, CBRs for reproductive output were determined as IC25 values of 2 and 3.1 {micro}mol/gdw, respectively. PAH sublethal effects on feeding rate were also investigated Adult copepods were exposed to {sup 14}C sediment-associated fluoranthene for 24 h were fed {sup 3}H-labeled algae for 3 h. Ingestion rate was significantly decreased at tissue concentrations as low as 1 {micro}mol/gdw and yielded an IC25 value of 0.6 {micro}mol/gdw. Similar findings were obtained using another species of estuarine copepod, Coullana sp. Non-polar narcotic compounds such as PAH cause a nonspecific disturbance of the functioning of cell membrane which results in decreased overall activity. Measurement of CBR associated with decreased feeding is proposed as a direct method to quantify sublethal narcotizing effects of organic compounds.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benjamin, Doug; /Tufts U.

We combine results from searches by the CDF and D0 Collaborations for a standard model Higgs boson (H) in the processes gg {yields} H {yields} W{sup +}W{sup -} and gg {yields} H {yields} ZZ in p{bar p} collisions at the Fermilab Tevatron Collider at {radical}s = 1.96 TeV. With 8.2 fb{sup -1} of integrated luminosity analyzed at CDF and 8.1 fb{sup -1} at D0, the 95% C.L. upper limit on {sigma}(gg {yields} H) x {Beta}(H {yields} W{sup +}W{sup -}) is 1.01 pb at m{sub H} = 120 GeV, 0.40 pb at m{sub H} = 165 GeV, and 0.47 pb atmore » m{sub H} = 200 GeV. Assuming the presence of a fourth sequential generation of fermions with large masses, we exclude at the 95% Confidence Level a standard-model-like Higgs boson with a mass between 124 and 286 GeV.« less

Effect of prepubertal and postpubertal growth and age at first calving on production and reproduction traits during the first 3 lactations in Holstein dairy cattle.

PubMed

Krpálková, L; Cabrera, V E; Vacek, M; Stípková, M; Stádník, L; Crump, P

2014-05-01

The objective of this study was to evaluate the effect of body condition score (BCS), body weight (BW), average daily weight gain (ADG), and age at first calving (AFC) of Holstein heifers on production and reproduction parameters in the 3 subsequent lactations. The data set consisted of 780 Holstein heifers calved at 2 dairy farms in the Czech Republic from 2007 to 2011. Their BW and BCS were measured at monthly intervals during the rearing period (5 to 18 mo of age), and the milk production and reproduction data of the first 3 lactations were collected over an 8-yr period (2005 to 2012). The highest milk yield in the first lactation was found in the group with medium ADG (5 to 14 mo of age; 0.949 to 0.850 kg of ADG). The highest average milk yield over lifetime performance was detected in heifers with the highest total ADG (≥ 0.950 kg/d). The difference in milk yield between the evaluated groups of highest ADG (in total and postpubertal growth ≥ 0.950 kg/d and in prepubertal growth ≥ 0.970 kg/d) and the lowest ADG (≤ 0.849 kg/d) was approximately 1,000 kg/305 d per cow. The highest milk yield in the first lactation was found in the group with the highest AFC ≥ 751 d, for which fat and protein content in the milk was not reduced. Postpubertal growth (11 to 14 mo of age) had the greatest effect on AFC. The group with lowest AFC ≤ 699 d showed a negative effect on milk yield but only in the first 100 d of the first parity. The highest ADG was detrimental to reproduction parameters in the first lactation. The highest BW at 14 mo (≥ 420 kg) led to lower AFC. Groups according to BCS at 14 mo showed no differences in AFC or milk yield in the first lactation or lifetime average production per lactation. We concluded that low AFC ≤ 699 d did not show a negative effect on subsequent production and reproduction parameters. Therefore, a shorter rearing period is recommended for dairy herds with suitable management. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

31 CFR 356.21 - How are awards at the high yield or discount rate calculated?

Code of Federal Regulations, 2010 CFR

2010-07-01

... discount rate calculated? 356.21 Section 356.21 Money and Finance: Treasury Regulations Relating to Money... high yield or discount rate calculated? (a) Awards to submitters. We generally prorate bids at the highest accepted yield or discount rate under § 356.20(a)(2) of this part. For example, if 80.15% is the...

Effective conversion of maize straw wastes into bio-hydrogen by two-stage process integrating H2 fermentation and MECs.

PubMed

Li, Yan-Hong; Bai, Yan-Xia; Pan, Chun-Mei; Li, Wei-Wei; Zheng, Hui-Qin; Zhang, Jing-Nan; Fan, Yao-Ting; Hou, Hong-Wei

2015-12-01

The enhanced H2 production from maize straw had been achieved through the two-stage process of integrating H2 fermentation and microbial electrolysis cells (MECs) in the present work. Several key parameters affecting hydrolysis of maize straw through subcritical H2O were optimized by orthogonal design for saccharification of maize straw followed by H2 production through H2 fermentation. The maximum reducing sugar (RS) content of maize straw reached 469.7 mg/g-TS under the optimal hydrolysis condition with subcritical H2O combining with dilute HCl of 0.3% at 230 °C. The maximum H2 yield, H2 production rate, and H2 content was 115.1 mL/g-TVS, 2.6 mL/g-TVS/h, and 48.9% by H2 fermentation, respectively. In addition, the effluent from H2 fermentation was used as feedstock of MECs for additional H2 production. The maximum H2 yield of 1060 mL/g-COD appeared at an applied voltage of 0.8 V, and total COD removal reached about 35%. The overall H2 yield from maize straw reached 318.5 mL/g-TVS through two-stage processes. The structural characterization of maize straw was also carefully investigated by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and X-ray diffraction (XRD) spectra.

Sub-supercritical liquefaction of rice stalk for the production of bio-oil: Effect of solvents.

PubMed

Li, Rundong; Li, Bingshuo; Yang, Tianhua; Kai, Xingping; Wang, Weidan; Jie, Yefei; Zhang, Yang; Chen, Guanyi

2015-12-01

The effect of solvents (water and ethanol) on liquefaction characteristics of rice stalk (RS) was investigated in an autoclave. The highest conversion and liquid yield in water and ethanol were 84.95 wt%, 72.62 wt% and 78.93wt%, 63.84 wt%, respectively. FTIR and GC-MS of the bio-oils obtained from subcritical water (SubH2O, 300°C) and supercritical ethanol (scEtOH, 300°C) indicated that the behavior of RS liquefaction depended on solvents used. The major components of bio-oil produced in SubH2O were ketones and phenols, while esters and phenols dominated in scEtOH. ICP-OES analysis showed that the concentrations of potassium (K) and sodium (Na) in the bio-oil obtained from scEtOH were 14-15 times higher than that obtained from SubH2O. Ethanol gave rise to an improvement in the bio-oil properties including water content, density, acidity and HHV. It was concluded that the bio-oil from RS can be effectively upgraded in scEtOH. Copyright © 2015 Elsevier Ltd. All rights reserved.

Aerobic Oxidation of Xylose to Xylaric acid in Water over Pt Catalysts.

PubMed

Saha, Basudeb; Sadula, Sunitha

2018-05-02

Energy-efficient catalytic conversion of biomass intermediates to functional chemicals can enable bio-products viable. Herein, we report an efficient and low temperature aerobic oxidation of xylose to xylaric acid, a promising bio-based chemical for the production of glutaric acid, over commercial catalysts in water. Among several heterogeneous catalysts investigated, Pt/C exhibits the best activity. Systematic variation of reaction parameters in the pH range of 2.5 to 10 suggests that the reaction is fast at higher temperatures but high C-C scission of intermediate C5-oxidized products to low carbon carboxylic acids undermines xylaric acid selectivity. The C-C cleavage is also high in basic solution. The oxidation at neutral pH and 60 C achieves the highest xylaric acid yield (64%). O2 pressure and Pt-amount have significant influence on the reactivity. Decarboxylation of short chain carboxylic acids results in formation of CO2, causing some carbon loss; however such decarboxylation is slow in the presence of xylose. The catalyst retained comparable activity, in terms of product selectivity, after five cycles with no sign of Pt leaching. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Impact of holding and equilibration time on post-thaw quality of shipped boar semen.

PubMed

Schäfer, J; Waberski, D; Jung, M; Schulze, M

2017-12-01

Cryopreservation of boar semen is of growing interest for breeding companies. Overnight-shipping of pre-diluted ejaculates to specialized laboratories offers a practicable method, but requires fine-tuned protocols. In this study, the impact of holding post shipping at 17°C for 2 or 24h (n=10 samples) and of equilibration in lactose-egg yolk extender without glycerol at 5°C for 2, 4, 24 or 48h (n=11 samples) before freezing was investigated. Sperm-rich fractions of ejaculates from 21 mature Pietrain boars were collected at a single boar stud. After pre-dilution (1+1, v:v) with Beltsville thawing solution, samples were sent to the laboratory. Temperature profiles during transport and initial equilibration time were recorded. Semen quality post-thaw (PT) was evaluated using CASA and flow cytometry. Holding of 2h after shipping resulted in higher sperm motility (P=0.013) and beat cross frequency (BCF; P=0.047) compared to 24h. Differences between both groups vanished with prolonged incubation at 38°C PT. Equilibration at 5°C for 4h yielded the highest motility and BCF, whereas the equilibration for 48h impaired sperm motility. Membrane integrity, mitochondrial activity and DNA fragmentation index were not affected by any protocol modification. In conclusion, processing of pre-diluted boar semen shipped overnight within 2h after arrival at the laboratory is preferred to 24h of additional holding at 17°C. Extending the equilibration period in lactose-egg yolk extender without glycerol at 5°C from 2h to 4h before freezing is recommended. Copyright © 2017 Elsevier B.V. All rights reserved.

Biogas production from rice straw by solid-state anaerobic digestion

NASA Astrophysics Data System (ADS)

Shitophyta, Lukhi Mulia; Budiyono, Fuadi, Ahmad M.

2015-12-01

Biogas production from lignocellulosic biomass can be used as an alternative fuel to replace fossil fuels. Lignocellulose can be obtained from agricultural crop residues, such as rice straw. The aims of this study were to determine the effects of F/I ratio, total solid content, and physical pretreatment on biogas production by solid-state anaerobic digestion. The kinetics of biogas production were also examined in this study. The results showed that the biogas yield decreased by the increasing of F/I ratio. Meanwhile, the increase TS content of 22% to 24% also decreased the biogas yield. Physical pretreatment had no a significant effect on biogas yield (p > 0.05). The highest biogas yield of 248.4 L/kg VS was obtained at an F/I ratio of 2, TS content of 22%, and particle size of 2 mm. The kinetics of biogas production from rice straw followed the first-order kinetic model with the highest rate constant (k) of 0.0861 day-1.

Optimization of enzymes-microwave-ultrasound assisted extraction of Lentinus edodes polysaccharides and determination of its antioxidant activity.

PubMed

Yin, Chaomin; Fan, Xiuzhi; Fan, Zhe; Shi, Defang; Gao, Hong

2018-05-01

Enzymes-microwave-ultrasound assisted extraction (EMUE) method had been used to extract Lentinus edodes polysaccharides (LEPs). The enzymatic temperature, enzymatic pH, microwave power and microwave time were optimized by response surface methodology. The yields, properties and antioxidant activities of LEPs from EMUE and other extraction methods including hot-water extraction, enzymes-assisted extraction, microwave-assisted extraction and ultrasound-assisted extraction were evaluated. The results showed that the highest LEPs yield of 9.38% was achieved with enzymatic temperature of 48°C, enzymatic pH of 5.0, microwave power of 440W and microwave time of 10min, which correlated well with the predicted value of 9.79%. Additionally, LEPs from different extraction methods possessed typical absorption peak of polysaccharides, which meant different extraction methods had no significant effects on type of glycosidic bonds and sugar ring of LEPs. However, SEM images of LEPs from different extraction methods were significantly different. Moreover, the different LEPs all showed antioxidant activities, but LEPs from EMUE showed the highest reducing power when compared to other LEPs. The results indicated LEPs from EMUE can be used as natural antioxidant component in the pharmaceutical and functional food industries. Copyright © 2018 Elsevier B.V. All rights reserved.

Primordial synthesis of amines and amino acids in a 1958 Miller H2S-rich spark discharge experiment

PubMed Central

Parker, Eric T.; Cleaves, Henderson J.; Dworkin, Jason P.; Glavin, Daniel P.; Callahan, Michael; Aubrey, Andrew; Lazcano, Antonio; Bada, Jeffrey L.

2011-01-01

Archived samples from a previously unreported 1958 Stanley Miller electric discharge experiment containing hydrogen sulfide (H2S) were recently discovered and analyzed using high-performance liquid chromatography and time-of-flight mass spectrometry. We report here the detection and quantification of primary amine-containing compounds in the original sample residues, which were produced via spark discharge using a gaseous mixture of H2S, CH4, NH3, and CO2. A total of 23 amino acids and 4 amines, including 7 organosulfur compounds, were detected in these samples. The major amino acids with chiral centers are racemic within the accuracy of the measurements, indicating that they are not contaminants introduced during sample storage. This experiment marks the first synthesis of sulfur amino acids from spark discharge experiments designed to imitate primordial environments. The relative yield of some amino acids, in particular the isomers of aminobutyric acid, are the highest ever found in a spark discharge experiment. The simulated primordial conditions used by Miller may serve as a model for early volcanic plume chemistry and provide insight to the possible roles such plumes may have played in abiotic organic synthesis. Additionally, the overall abundances of the synthesized amino acids in the presence of H2S are very similar to the abundances found in some carbonaceous meteorites, suggesting that H2S may have played an important role in prebiotic reactions in early solar system environments. PMID:21422282

Primordial Synthesis of Amines and Amino Acids in a 1958 Miller H2S-Rich Spark Discharge Experiment

NASA Technical Reports Server (NTRS)

Parker, Eric T.; Cleaves, Henderson J.; Dworkin, Jason P.; Glavin, Daniel P.; Callahan, Michael; Aubrey, Andrew; Lazcano, Antonio; Bada, Jeffrey L.

2011-01-01

Archived samples from a previously unreported 1958 Stanley Miller electric discharge experiment containing hydrogen sulfide (H2S) were recently discovered and analyzed using high-performance liquid chromatography and time-of-flight mass spectrometry. We report here the detection and quantification of primary amine-containing compounds in the original sample residues, which were produced via spark discharge using a gaseous mixture of H2S, CH4, NH3, and CO2. A total of 23 amino acids and 4 amines, including 7 organosulfur compounds, were detected in these samples. The major amino acids with chiral centers are racemic within the accuracy of the measurements, indicating that they are not contaminants introduced during sample storage. This experiment marks the first synthesis of sulfur amino acids from spark discharge experiments designed to imitate primordia! environments. The relative yield of some amino acids, in particular the isomers of aminobutyric acid, are the highest ever found in a spark discharge experiment. The simulated primordial conditions used by Miller may serve as a model for early volcanic plume chemistry and provide insight to the possible roles such plumes may have played in abiotic organic synthesis. Additionally, the overall abundances of the synthesized amino acids in the presence of H2S are very similar to the abundances found in some carbonaceous meteorites, suggesting that H2S may have played an important role in prebiotic reactions in early solar system environments.

Understanding the Relationship Between Kinetics and Thermodynamics in CO 2 Hydrogenation Catalysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jeletic, Matthew S.; Hulley, Elliott B.; Helm, Monte L.

Linear free-energy relationships have been identified that link the kinetic activity for catalytic hydrogenation of CO2 to formate with the thermodynamic driving force for the rate-limiting steps of catalysis. Cobalt and rhodium bis(diphosphine) complexes with different hydricities (G°H-), acidities (pKa), and free energies for H2 addition (G°H2) were examined. Catalytic CO2 hydrogenation was studied under 1.8 and 20 atm of pressure (1:1 CO2:H2) at room temperature in tetrahydrofuran with a spread of turnover frequencies (TOF) ranging from 0 to 74,000 h-1. The catalysis was followed by 1H and 31P NMR in real time under all conditions to yield information aboutmore » the rate determining step. Catalysts exhibiting the highest activities were found to have hydride transfer and hydrogen addition steps that were each downhill by approximately 6 to 7 kcal/mol, and the deprotonation step was thermoneutral. The research by M.S.J., A.M.A., E.S.W., and J.C.L. was supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences, and Biosciences. The research by E.B.H., M.L.H., and M.T.M. (X-ray crystallography, synthesis) was supported as part of the Center for Molecular Electrocatalysis, an Energy Frontier Research Center funded by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences. The authors thank Dr. Samantha A. Burgess for assistance in collecting cyclic voltammetry data. Pacific Northwest National Laboratory is operated by Battelle for the U.S. Department of Energy.« less

Complete factorial design to adjust pH and sugar concentrations in the inoculum phase of Ralstonia solanacearum to optimize P(3HB) production

PubMed Central

Alves, Mariane Igansi; Rodrigues, Amanda Ávila; Furlan, Lígia; da Silva Rodrigues, Rosane; Diaz de Oliveira, Patrícia; Vendruscolo, Claire Tondo; da Silveira Moreira, Angelita

2017-01-01

Poly(3-hydroxybutyrate) (P(3HB)) is a biodegradable plastic biopolymer that accumulates as lipophilic inclusions in the cytoplasm of some microorganisms. The biotechnological process by which P(3HB) is synthesized occurs in two phases. The first phase involves cell growth in a complex culture medium, while the second phase involves polymer accumulation in the presence of excess carbon sources. As such, the efficiency of the second phase depends on the first phase. The aim of this study was to evaluate culture media with different concentrations of sucrose and glucose and different pH values in the inoculum phase of Ralstonia solanacearum RS with the intention of identifying methods by which the biomass yield could be increased, subsequently enhancing the yield of P(3HB). The culture medium was formulated according to the experimental planning type of central composite rotational design 22. The independent variables were pH and sugar concentration (sucrose and glucose), and the dependent variables were OD600nm, dry cell weight (DCW), and P(3HB) yield. The highest cell growth, estimated by the OD600nm (20.6) and DCW (5.35) values, was obtained when sucrose was used in the culture medium at a concentration above 35 g.L-1 in combination with an acidic pH. High polymer (45%) accumulation was also achieved under these conditions. Using glucose, the best results for OD600nm (12.5) and DCW (2.74) were also obtained at acidic pH but with a sugar concentration at the minimum values evaluated. Due to the significant accumulation of polymer in the cells that were still in the growth phase, the accumulating microorganism P(3HB) Ralstonia solanacearum RS can be classified as having type II metabolism in relation to the polymer accumulation phase, which is different from other Ralstonia spp. studied until this time. PMID:28704411

Supercritical fluid extraction of ginger (Zingiber Officinale Var. Amarum) : Global yield and composition study

NASA Astrophysics Data System (ADS)

Fitriady, Muhammad Arifuddin; Sulaswatty, Anny; Agustian, Egi; Salahuddin, Aditama, Deska Prayoga Fauzi

2017-11-01

An experiment to observe the effect of temperature and time process in ginger rhizome-Supercritical Fluid Extraction (SFE) using CO2 as the solvent has been conducted. The ginger rhizome (Zingiber Officinale Var. Amarum) was washed, drained, sliced, sun-dried, and then stored in a sealed bag prior to usage. The temperature and time process variables are each 35, 40, 45°C and 2, 4, 6 hours respectively with the pressure variable are 3500, 4000, and 4500 psi. It is found that the highest yield (2.9%) was achieved using temperature of 40°C and pressure of 4500 psiwith the process time of 4 hours. However, using the curve-fitting method, it is suggested to use 42°C as the temperature and 5 hours, 7 minutes, and 30 seconds (5.125 Hours) as the time process to obtain the highest yield. The temperature changes will affect both solvent and vapor pressure of diluted compounds of the ginger which will influence the global yield and the composition of the extract. The three major components of the extract are curcumene, zingiberene, and β - sesquipellandrene,

Hydrology of area 2, Eastern Coal Province, Pennsylvania and New York

USGS Publications Warehouse

Herb, W.J.; Brown, D.E.; Shaw, L.C.; Stoner, J.E.; Felbinger, J.K.

1983-01-01

Provisions of the Surface Mining Control and Reclamation Act of 1977 recognized a nationwide need for hydrologic information in mined and potentially mined areas. This report is designed to be useful to mine owners, operators, regulatory authorities, citizens groups, and others by presenting information on existing hydrologic conditions and by identifying additional sources of hydrologic information. General hydrologic information is presented in a brief text accompanied by a map, chart, graph, or other illustration for each of a series of water-resourcesrelated topics. The summation of the topical discussions provides a description of the hydrology of the area. The Eastern Coal Province has been divided into 24 hydrologic study areas which are shown on the cover of this report. The divisions are based on hydrologic factors, location, and size. Hydrologic units (surface drainage basins) or parts of units are combined to form each study area. Study Area 2 covers northwestern Pennsylvania and a small part of southwestern New York. Most exposed bedrock is of Pennsylvanian, Mi;;sissippian, or Devonian ages. Glacial drift covers most of the bedrock in the northwestern part of the area. During 1979, more than 7 million tons of bituminous coal was produced from about 230 mines in Area 2 counties. Over 99 percent of the area's coal production is from surface mining. Streamflow data are available for 18 continuousrecord stations; 1 crest-stage, partial-record station; 1 low-flow, partial-record station; and 65 miscellaneous sites. Water-quality data are available for 78 locations. Streams having the highest median specific conductance, highest median dissolved-solids concentrations, lowest median pH, highest median total-iron concentration, highest median total-manganese concentration, and highest dissolved-sulfate concentrations were found in Clarion County, the leading coal-producing county in the area. Statistics on low flow, mean flow, peak flow, and flow duration for gaging stations can be computed from recorded mean daily flows. Similar statistics can be estimated for ungaged streams by regression and graphical techniques. Five ground-water observation wells are being operated in Area 2. Ground-water levels fluctuate seasonally. Depth to water increases with well depth in upland areas and decreases with well depth in valleys. Well yields in the area range from less than 1 to more than 2,000 gallons per minute. Wells in unconsolidated materials usually have higher yields. Ground-water quality is adequate for most domestic purposes, except locally. Additional water-data information are available through: (1) The National Water Data Exchange, (2) The National Water Data Storage and Retrieva

Streamflow and estimated loads of phosphorus and dissolved and suspended solids from selected tributaries to Lake Ontario, New York, water years 2012–14

USGS Publications Warehouse

Hayhurst, Brett A.; Fisher, Benjamin N.; Reddy, James E.

2016-07-20

This report presents results of the evaluation and interpretation of hydrologic and water-quality data collected as part of a cooperative program between the U.S. Geological Survey and the U.S. Environmental Protection Agency. Streamflow, phosphorus, and solids dissolved and suspended in stream water were the focus of monitoring by the U.S. Geological Survey at 10 sites on 9 selected tributaries to Lake Ontario during the period from October 2011 through September 2014. Streamflow yields (flow per unit area) were the highest from the Salmon River Basin due to sustained yields from the Tug Hill aquifer. The Eighteenmile Creek streamflow yields also were high as a result of sustained base flow contributions from a dam just upstream of the U.S. Geological Survey monitoring station at Burt. The lowest streamflow yields were measured in the Honeoye Creek Basin, which reflects a decrease in flow because of withdrawals from Canadice and Hemlock Lakes for the water supply of the City of Rochester. The Eighteenmile Creek and Oak Orchard Creek Basins had relatively high yields due in part to groundwater contributions from the Niagara Escarpment and seasonal releases from the New York State Barge Canal.Annual constituent yields (load per unit area) of suspended solids, phosphorus, orthophosphate, and dissolved solids were computed to assess the relative contributions and allow direct comparison of loads among the monitored basins. High yields of total suspended solids were attributed to agricultural land use in highly erodible soils at all sites. The Genesee River, Irondequoit Creek, and Honeoye Creek had the highest concentrations and largest mean yields of total suspended solids (165 short tons per square mile [t/mi2], 184 t/mi2, and 89.7 t/mi2, respectively) of the study sites.Samples from Eighteenmile Creek, Oak Orchard Creek at Kenyonville, and Irondequoit Creek had the highest concentrations and largest mean yields of phosphorus (0.27 t/mi2, 0.26 t/mi2, and 0.20 t/mi2, respectively) and orthophosphate (0.17 t/mi2, 0.13 t/mi2, and 0.04 t/mi2, respectively) of the study sites. These results were attributed to a combination of sources, including discharges from wastewater treatment plants, diversions from the New York State Barge Canal, and manure and fertilizers applied to agricultural land. Yields of phosphorus also were high in the Genesee River Basin (0.17 t/mi2) and were presumably associated with nutrient and sediment transport from agricultural land and from streambank erosion. The Salmon and Black Rivers, which drain a substantial amount of forested land and are influenced by large groundwater discharges, had the lowest concentrations and yields of phosphorus and orthophosphate of the study sites.Mean annual yields of dissolved solids were the highest in Irondequoit Creek due to a high percentage of urbanized area in the basin and in Oak Orchard Creek at Kenyonville and in Eighteenmile Creek due to groundwater contributions from the Niagara Escarpment. High yields of dissolved solids of 840 t/mi2, 829 t/mi2, and 715 t/mi2, respectively, from these basins can be attributed to seasonal chloride yields associated with use of road deicing salts. The Niagara Escarpment can produce large amounts of dissolved solids from the dissolution of minerals (a continual process reflected in base flow samples). Groundwater inflows in the Salmon River have very low concentrations of dissolved solids due to minimal bedrock interaction along the Tug Hill Plateau and discharge from the Tug Hill sand and gravel aquifer, which has minimal mineralization.

[Effects of irrigation amount and various fertigation methods on yield and quality of cucumber in greenhouse].

PubMed

Fang, Dong-ping; Zhang, Fu-cang; Li, Jing; Wang, Hai-dong; Xiang, You-zhen; Zhang, Yan

2015-06-01

Taking cucumber as experimental plant, an experiment was conducted to study the effects of irrigation amount and fertigation methods on growth, yield and quality of cucumber in greenhouse. The experiment had designed two irrigation levels, i.e. 100% ET0 (W1) and 75% ET0 (W2), and four fertigation fertilization ratios, i.e. 100%, 66.6%, 33.3% and 0% (Z100, Z66 , Z33, Z0) fertigation of a total amount of (360:180:540 kg · hm(-2)) (N:P2O5:K2O) by 8 times with the corresponding remainders (0%, 33.3%, 66.6% and 100%) were applied to soil as basic fertilization before the planting according to the recommended fertilization rate, and no fertilizer treatment was set up as the control (CK). Results showed that irrigation and fertilization levels had positive correlations with plant height, leaf areas, dry mass, yield and quality of cucumber. Yield at W1Z100 was the highest, reaching 67760 kg · hm(-2). W2 treatment increased the mean water use efficiency (WUE) by 9.4% compared to W1. W2Z100 treatment had the highest WUE, reaching 47.13 kg · m(-3). Yield at W2Z100 was only 3.4% lower than the maximum, but saved 25% of water. Yield and dry matter at Z100 were 15.3% and 16.8% higher than at Z0, respectively, the cucumber fruit vitamin C, soluble protein and soluble sugar contents were increased, and the water use efficiency was increased by 19.1%. W2Z100 treatment was the best treatment which could enable cucumber to obtain both the high-yield and the high-quality.

Synthesis of fatty acid methyl ester from palm oil (Elaeis guineensis) with Ky(MgCa)2xO3 as heterogeneous catalyst.

PubMed

Olutoye, M A; Lee, S C; Hameed, B H

2011-12-01

Fatty acid methyl esters (FAME) were produced from palm oil using eggshell modified with magnesium and potassium nitrates to form a composite, low-cost heterogeneous catalyst for transesterification. The catalyst, prepared by the combination of impregnation/co-precipitation was calcined at 830 °C for 4 h. Transesterification was conducted at a constant temperature of 65 °C in a batch reactor. Design of experiment (DOE) was used to optimize the reaction parameters, and the conditions that gave highest yield of FAME (85.8%) was 5.35 wt.% catalyst loading at 4.5 h with 16:1 methanol/oil molar ratio. The results revealed that eggshell, a solid waste, can be utilized as low-cost catalyst after modification with magnesium and potassium nitrates for biodiesel production. Copyright © 2011 Elsevier Ltd. All rights reserved.

Effect of water treatment sludge on growth and elemental composition of tomato (Lycopersicon esculentum) shoots

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elliott, H.A.; Singer, L.M.

The impact of a water treatment sludge on the fertility of a silt loam soil was assessed by monitoring the yield and elemental composition of tomato (Lycopersicon esculentum) shoots in a greenhouse study. Application of sludge at rates from 2-10% (air dry weight basis) raised the soil pH from 5.3 to 8.0 which enhanced plant growth. A substantial reduction in metal (Cd, Zn, Cu, Ni) uptake was observed with sludge amendments, even at the highest rates. The alkaline nature of this sludge (pH=9.3, calcium carbonate equivalence=53%) suggest its potential use as a liming material for agricultural soils. Overly alkaline conditionsmore » should be avoided however, as high application rates combined with ammonia fertilization had an antagonistic effect on plant growth, possibly from P deficiency induced by struvite (MgNH{sub 4}PO{sub 4}) formation.« less

A new method for the simultaneous enhancement of methane yield and reduction of hydrogen sulfide production in the anaerobic digestion of waste activated sludge.

PubMed

Dai, Xiaohu; Hu, Chongliang; Zhang, Dong; Chen, Yinguang

2017-11-01

The biogas generated from anaerobic digestion (AD) also includes undesirable by-product such as hydrogen sulfide (H 2 S), which must be removed before the biogas can be used as a clean energy source. Therefore, it is necessary to find an appropriate strategy to simultaneously enhance the methane yield and reduce H 2 S production. An efficient strategy-pretreating sludge at pH 10 for 8d and adjusting the system at neutral pH to produce methane for 20d-is reported for the synchronous enhancement of methane production and reduction of H 2 S production during AD. The experimental results showed that the cumulative methane yield was 861.2±6.1mL/g volatile solids (VS) of sludge pretreated at pH 10 in semi-continuous stirred anaerobic reactors for 84d, an increase of 49.6% over the yield in the control. Meanwhile, the cumulative production of H 2 S was 144.1×10 -4 mL/g VS, 54.2% lower than that in the control. Copyright © 2017 Elsevier Ltd. All rights reserved.

Single, binary and multi-component adsorption of some anions and heavy metals on environmentally friendly Carpobrotus edulis plant.

PubMed

Chiban, Mohamed; Soudani, Amina; Sinan, Fouad; Persin, Michel

2011-02-01

A low-cost adsorbent and environmentally friendly adsorbent from Carpobrotus edulis plant was used for the removal of NO(3)(-), H(2)PO(4)(-), Pb(2+) and Cd(2+) ions from single, binary and multi-component systems. The efficiency of the adsorbent was studied using batch adsorption technique under different experimental conditions by varying parameters such as pH, initial concentration and contact time. In single component systems, the dried C. edulis has the highest affinity for Pb(2+), followed by NO(3)(-), Cd(2+) and H(2)PO(4)(-), with adsorption capacities of 175mg/g, 125mg/g, 28mg/g and 26mg/g, respectively. These results showed that the adsorption of NO(3)(-) and H(2)PO(4)(-) ions from single and binary component systems can be successfully described by Langmuir and Freundlich isotherms. Freundlich adsorption model, showed the best fit to the single and binary experimental adsorption data. These results also indicated that the adsorption yield of Pb(2+) ion was reduced by the presence of Cd(2+) ion in binary metal mixture. The competitive adsorption of NO(3)(-), H(2)PO(4)(-), Pb(2+) and Cd(2+) ions on dried C. edulis plant shows that NO(3)(-) and H(2)PO(4)(-) anions are able to adsorb on different free binding sites and Pb(2+) and Cd(2+) cations are able to adsorb on the same active sites of C. edulis particles. The dried C. edulis was found to be efficient in removing nitrate, phosphate, cadmium and lead from aqueous solution as compared to other adsorbents already used for the removal of these ions. Copyright © 2010 Elsevier B.V. All rights reserved.

Effect of total solid content and pretreatment on the production of lactic acid from mixed culture dark fermentation of food waste.

PubMed

Yousuf, Ahasa; Bastidas-Oyanedel, Juan-Rodrigo; Schmidt, Jens Ejbye

2018-04-28

Food waste landfilling causes environmental degradation, and this work assesses a sustainable food valorization technique. In this study, food waste is converted into lactic acid in a batch assembly by dark fermentation without pH control and without the addition of external inoculum at 37 °C. The effect of total solid (TS), enzymatic and aeration pretreatment was investigated on liquid products concentration and product yield. The maximum possible TS content was 34% of enzymatic pretreated waste, and showed the highest lactic acid concentration of 52 g/L, with a lactic acid selectivity of 0.6 g lactic /g totalacids . The results indicated that aeration pretreatment does not significantly improve product concentration or yield. Non-pretreated waste in a 29% TS system showed a lactic acid concentration of 31 g/L. The results showed that enzymatic pretreated waste at TS of 34% results in the highest production of lactic acid. Copyright © 2018 Elsevier Ltd. All rights reserved.

Tunneling chemical reactions D+H{sub 2}{yields}DH+H and D+DH{yields}D{sub 2}+H in solid D{sub 2}-H{sub 2} and HD-H{sub 2} mixtures: An electron-spin-resonance study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumada, Takayuki

2006-03-07

Tunneling chemical reactions D+H{sub 2}{yields}DH+H and D+DH{yields}D{sub 2}+H in solid HD-H{sub 2} and D{sub 2}-H{sub 2} mixtures were studied in the temperature range between 4 and 8 K. These reactions were initiated by UV photolysis of DI molecules doped in these solids for 30 s and followed by measuring the time course of electron-spin-resonance (ESR) intensities of D and H atoms. ESR intensity of D atoms produced by the photolysis decreases but that of H atoms increases with time. Time course of the D and H intensities has the fast and slow processes. The fast process, which finishes within {approx}300more » s after the photolysis, is assigned to the reaction of D atom with one of its nearest-neighboring H{sub 2} molecules, D(H{sub 2}){sub n}(HD){sub 12-n}{yields}H(H{sub 2}){sub n-1}(HD){sub 13-n} or D(H{sub 2}){sub n}(D{sub 2}){sub 12-n}{yields}H(HD)(H{sub 2}){sub n-1}(D{sub 2}){sub 12-n} for 12{>=}n{>=}1. Rate constant for the D+H{sub 2} reaction between neighboring D atom-H{sub 2} molecule pair is determined to be (7.5{+-}0.7)x10{sup -3} s{sup -1} in solid HD-H{sub 2} and (1.3{+-}0.3)x10{sup -2} s{sup -1} in D{sub 2}-H{sub 2} at 4.1 K, which is very close to that calculated based on the theory of chemical reaction in gas phase by Hancock et al. [J. Chem. Phys. 91, 3492 (1989)] and Takayanagi and Sato [J. Chem. Phys. 92, 2862 (1990)]. This rate constant was found to be independent of temperature up to 7 K within experimental error of {+-}30%. The slow process is assigned to the reaction of D atom produced in a cage fully surrounded by HD or D{sub 2} molecules, D(HD){sub 12} or D(D{sub 2}){sub 12}. This D atom undergoes the D+DH reaction with one of its nearest-neighboring HD molecules in solid HD-H{sub 2} or diffuses to the neighbor of H{sub 2} molecules to allow the D+H{sub 2} reaction in solid HD-H{sub 2} and D{sub 2}-H{sub 2}. The former is the main channel in solid HD-H{sub 2} below 6 K where D atoms diffuse very slowly, whereas the latter dominates over the former above 6 K. Rate for the reactions in the slow process is independent of temperature below 6 K but increases with the increase in temperature above 6 K. We found that the increase is due to the increase in hopping rate of D atoms to the neighbor of H{sub 2} molecules. Rate constant for the D+DH reaction was found to be independent of temperature up to 7 K as well.« less

High-level production of β-1,3-1,4-glucanase by Rhizomucor miehei under solid-state fermentation and its potential application in the brewing industry.

PubMed

Yang, S Q; Xiong, H; Yang, H Y; Yan, Q J; Jiang, Z Q

2015-01-01

To improve the β-1,3-1,4-glucanase production by Rhizomucor miehei under solid-state fermentation (SSF) for industrial application. The fermentation conditions for β-1,3-1,4-glucanase production by R. miehei CAU432 under SSF were optimized using a 'one-factor-at-a-time' method. Under the optimized fermentation conditions, viz. oatmeal (0·45-0·9 mm) as sole carbon source, 5% (w/w) peptone as sole nitrogen source, initial moisture of 80% (w/w), initial culture pH of 5·0, incubation temperature of 50°C and incubation time of 6 days, the highest β-1,3-1,4-glucanase activity of 20,025 U g(-1) dry substrate was achieved, which represents the highest yield for β-1,3-1,4-glucanase production ever reported. The crude enzyme was extracted and purified to homogeneity with a purification fold of 4·6 and a recovery yield of 9·0%. The addition of the purified β-1,3-1,4-glucanase in mash obviously reduced its filtration time (24·6%) and viscosity (2·61%). The optimal fermentation conditions for maximal β-1,3-1,4-glucanase production under SSF was obtained, and the enzyme was suitable for application in the malting process. The high production yield and excellent capability of the enzyme may enable it great potential in industries, especially in brewing industry. © 2014 The Society for Applied Microbiology.

Comparison of artificial maturation of lignite in hydrous and nonhydrous conditions

USGS Publications Warehouse

Behar, F.; Lewan, M.D.; Lorant, F.; Vandenbroucke, M.

2003-01-01

The objectives of the study are to compare product compositions and yields generated from lignite artificially matured by open nonhydrous pyrolysis, closed nonhydrous pyrolysis, and hydrous pyrolysis. The pyrolysis products were fractionated into CO2, H2O, CH4, C2-C5, C8-C14, C14+ saturates, C14+ aromatics and NSOs (resins+asphaltenes). All three methods generated high and similar quantities of water during pyrolysis that ranged between 14.6 and 15.2 wt.% of the original lignite. As a result of this high water content generated by the lignite, the experiments with no added water are referred to as nonhydrous rather than anhydrous. Rock-Eval pyrolysis and elemental analyses were conducted on the recovered lignite after solvent extraction to determine their residual hydrocarbon generation potential and to plot their position in a van Krevelen diagram, respectively. Residual lignite from the closed nonhydrous and hydrous experiments showed relationships between vitrinite reflectance (%Ro) values and atomic H/C ratios that occurred within the fields observed for natural maturation of coal. Although no significant differences in the atomic H/C ratios were observed between closed nonhydrous and hydrous pyrolysis, the vitrinite reflectance values were on the average 0.2% Ro lower in the residual lignite from the nonhydrous experiments. The remaining hydrocarbon generation potential as determined by Rock-Eval pyrolysis of the residual lignite showed that the nonhydrous residuals had on the average 16 mg more hydrocarbon potential per gram of original lignite than the hydrous residuals. This suggests there is a better release of the pyrolysis products from the lignite network in the hydrous experiments once generation occurs. For gas generation, at maximum yields, open nonhydrous pyrolysis generates the most hydrocarbon gas (21.0 mg/g original lignite), which is 20% more than closed nonhydrous pyrolysis and 29% more than hydrous pyrolysis. Closed nonhydrous pyrolysis generates on the average 14% more gas than hydrous pyrolysis, but the proportionality of the generated hydrocarbon gases is essentially the same for both pyrolysis methods. At maximum yields, CO2 generation is greatest in hydrous pyrolysis (99.5 mg/g original lignite), with yields being 37 percent higher than closed nonhydrous pyrolysis and 26% higher than open nonhydrous pyrolysis. The maximum yields of C14+ products are highest and similar for open nonhydrous pyrolysis and hydrous pyrolysis (125.6 and 125.9 mg/g lignite, respectively), and are more than 70% higher than closed nonhydrous pyrolysis. This difference in the maximum yields of C14+ products can be explained by differences in the proportionality between either cracking reactions that result in liquid product and char formation or trapping of generated products within the coal network (cross-linking reactions). Maximum yields of C14+ aliphatics from hydrous experiments may not have been attained, but the maximums that were observed and their GC traces are similar for the three pyrolysis systems.

Hepatitis A Virus Disinfection in Water by Solar Photo-Fenton Systems.

PubMed

Polo, David; García-Fernández, Irene; Fernández-Ibañez, Pilar; Romalde, Jesús L

2018-06-01

This study evaluates and compares the effectiveness of solar photo-Fenton systems for the inactivation of hepatitis A virus (HAV) in water. The effect of solar irradiance, dark- Fenton reaction and three different reactant concentrations (2.5/5, 5/10 and 10/20 mg/L of Fe 2+ /H 2 O 2 ) on the photo-Fenton process were tested in glass bottle reactors (200 mL) during 6 h under natural sunlight. Disinfection kinetics were determined both by RT-qPCR and infectivity assays. Mean water temperatures ranged from 25 to 27.3 °C, with a maximum local noon UV irradiances of 22.36 W/m 2 . Photo-Fenton systems yielded increased viral reduction rates in comparison with the isolated effect under the Fenton reaction in darkness (negligible viral reduction) or the solar radiation (0.25 Log of RNA reduction). With the highest concentration employed (10-20 mg/L Fe 2+ -H 2 O 2 ), an average RNA reduction rate of ~ 1.8 Log (initial concentration of 10 5 pfu/mL) and a reduction of 80% in the infectivity capacity were reached. Results showed a strong synergistic effect between Fe 2+ /H 2 O 2 and sunlight, demonstrating that significant disinfection rates of HAV under photo-Fenton systems may occur with relatively higher efficiency at middle environmental temperatures and without the need for an energy-intensive light source.

In silico aided metabolic engineering of Klebsiella oxytoca and fermentation optimization for enhanced 2,3-butanediol production.

PubMed

Park, Jong Myoung; Song, Hyohak; Lee, Hee Jong; Seung, Doyoung

2013-09-01

Klebsiella oxytoca naturally produces a large amount of 2,3-butanediol (2,3-BD), a promising bulk chemical with wide industrial applications, along with various byproducts. In this study, the in silico gene knockout simulation of K. oxytoca was carried out for 2,3-BD overproduction by inhibiting the formation of byproducts. The knockouts of ldhA and pflB genes were targeted with the criteria of maximization of 2,3-BD production and minimization of byproducts formation. The constructed K. oxytoca ΔldhA ΔpflB strain showed higher 2,3-BD yields and higher final concentrations than those obtained from the wild-type and ΔldhA strains. However, the simultaneous deletion of both genes caused about a 50 % reduction in 2,3-BD productivity compared with K. oxytoca ΔldhA strain. Based on previous studies and in silico investigation that the agitation speed during 2,3-BD fermentation strongly affected cell growth and 2,3-BD synthesis, the effect of agitation speed on 2,3-BD production was investigated from 150 to 450 rpm in 5-L bioreactors containing 3-L culture media. The highest 2,3-BD productivity (2.7 g/L/h) was obtained at 450 rpm in batch fermentation. Considering the inhibition of acetoin for 2,3-BD production, fed-batch fermentations were performed using K. oxytoca ΔldhA ΔpflB strain to enhance 2,3-BD production. Altering the agitation speed from 450 to 350 rpm at nearly 10 g/L of acetoin during the fed-batch fermentation allowed for the production of 113 g/L 2,3-BD, with a yield of 0.45 g/g, and for the production of 2.1 g/L/h of 2,3-BD.

Efficient solar-to-fuels production from a hybrid microbial-water-splitting catalyst system.

PubMed

Torella, Joseph P; Gagliardi, Christopher J; Chen, Janice S; Bediako, D Kwabena; Colón, Brendan; Way, Jeffery C; Silver, Pamela A; Nocera, Daniel G

2015-02-24

Photovoltaic cells have considerable potential to satisfy future renewable-energy needs, but efficient and scalable methods of storing the intermittent electricity they produce are required for the large-scale implementation of solar energy. Current solar-to-fuels storage cycles based on water splitting produce hydrogen and oxygen, which are attractive fuels in principle but confront practical limitations from the current energy infrastructure that is based on liquid fuels. In this work, we report the development of a scalable, integrated bioelectrochemical system in which the bacterium Ralstonia eutropha is used to efficiently convert CO2, along with H2 and O2 produced from water splitting, into biomass and fusel alcohols. Water-splitting catalysis was performed using catalysts that are made of earth-abundant metals and enable low overpotential water splitting. In this integrated setup, equivalent solar-to-biomass yields of up to 3.2% of the thermodynamic maximum exceed that of most terrestrial plants. Moreover, engineering of R. eutropha enabled production of the fusel alcohol isopropanol at up to 216 mg/L, the highest bioelectrochemical fuel yield yet reported by >300%. This work demonstrates that catalysts of biotic and abiotic origin can be interfaced to achieve challenging chemical energy-to-fuels transformations.

Chrysanthemum morphology, photosynthetic efficiency and antioxidant capacity are differentially modified by light quality.

PubMed

Zheng, Liang; Van Labeke, Marie-Christine

2017-06-01

The effect of light quality on leaf morphology, photosynthetic efficiency and antioxidant capacity of leaves that fully developed under a specific spectrum was investigated in Chrysanthemum cv. Four light treatments were applied at 100μmolm -2 s -1 and a photoperiod of 14h using light-emitting diodes, which were 100% red (R), 100% blue (B), 75% red with 25% blue (RB) and white (W), respectively. Intraspecific variation was investigated by studying the response of eight cultivars. Overall, red light significantly decreased the leaf area while the thinnest leaves were observed for W. Chlorophyll content and Chl a/b ratio was highest for W and lowest under R. B and RB resulted in the highest maximum quantum yield (F v /F m ) and quantum efficiency (Φ PSII ). A negative correlation between heat dissipation (NPQ) and Φ PSII was found. Blue light induced the highest hydrogen peroxide content, which is a proxy for total ROS generation, followed by W and RB while low contents were found under R. The antioxidative response was not always correlated with hydrogen content and differed depending on the light quality treatment. Blue light enhanced the proline levels, while carotenoids, total flavonoid and phenolic compounds were higher under W. Intraspecific variation in the responses were observed for most parameters with exception of leaf thickness; this intraspecific variation was most pronounced for total phenolic and flavonoid compounds. Copyright © 2017 Elsevier GmbH. All rights reserved.

Supplementary effects of higher levels of various disaccharides on processing yield, quality properties and sensory attributes of Chinese - style pork jerky.

PubMed

Chen, Chih-Ming; Lin, Hsien-Tang

2017-12-01

This study evaluated the supplementary effect of higher concentrations of various disaccharides on processing yield, major physicochemical properties, and sensory attributes of Chinese-style pork jerky (CSPJ). CSPJ samples were prepared by marinating sliced ham (4 mm) with three dissaccharides, including sucrose, lactose, and maltose, at 0%, 15%, 18%, 21%, and 24%. Subsequently, the CSPJ samples were dried and roasted. The moisture content, water activity, crude protein, moisture-to-protein ratio, pH, processing yield, shear force, color, and sensory attributes of the CSPJ samples were evaluated. The quality characteristics of CSPJ samples prepared with sucrose were more acceptable. By contrast, CSPJ samples prepared with lactose showed the lowest scores. However, the processing yield and moisture content were the highest for CSPJ samples prepared with lactose, which may be associated with improved benefits for cost reduction. Furthermore, sucrose and lactose supplementation resulted in contrasting quality characteristics; for example, CSPJ samples with sucrose and maltose supplementation had higher sensory scores for color than samples with lactose supplementation. Additionally, most quality characteristics of CSPJ samples with sucrose supplementation contrasted with those of the samples with lactose supplementation; for example, the samples with sucrose supplementation had higher scores for sensory attributes than those with lactose supplementation. Sucrose supplementation up to 21% to 24% was associated with the highest overall acceptability scores (5.19 to 5.80), enhanced quality characteristics, increased processing yield, and reduced production cost.

Sensitivity of wheat and rice to low levels of atmospheric ethylene

NASA Technical Reports Server (NTRS)

Klassen, Stephen P.; Bugbee, Bruce

2002-01-01

Ethylene (C2H4) gas is produced throughout the life cycle of plants and can accumulate in closed growth chambers to levels 100 times higher than in outside environments. Elevated atmospheric C2H4 can cause a variety of abnormal responses, but the sensitivity to elevated C2H4 is not well characterized. We evaluated the C2H4 sensitivity of wheat (Triticum aestivum L.) and rice (Oryza sativa L.) in five studies. The first three studies compared the effects of continuous C2H4 levels ranging from 0 to 1000 nmol mol-1 (ppb) in a growth chamber throughout the life cycle of the plants. A short-term 1000 nmol mol-1 treatment was included in which exposure was stopped at anthesis. Yield was reduced by 36% in wheat and 63% in rice at 50 nmol mol-1 and both species were virtually sterile when continuously exposed to 1000 nmol mol-1. However, the yield reductions were much less with exposure that stopped at anthesis, suggesting the detrimental effect of C2H4 on yield was greatest around the time of seed set. Two additional studies evaluated the differential sensitivity of two wheat cultivars (Super Dwarf and USU-Apogee) to 50 nmol mol-1 C2H4 at three CO2 levels [350, 1200, 5000 micromoles mol-1 (ppm)] in a greenhouse. Yield of USU-Apogee was not significantly reduced by C2H4 but the yield of Super Dwarf was reduced by 60%. Elevated CO2 did not influence the sensitivity to C2H4. A difference in the C2H4 sensitivity of USU-Apogee between greenhouse and growth chamber trials suggests that C2H4 sensitivity is dependent on the environment. Collectively, the data suggest that relatively low levels of C2H4 could induce anomalous plant responses by accumulation in greenhouses and growth chambers with inadequate ventilation. The data also suggest that C2H4 sensitivity can be reduced by both genetic and environmental manipulations. 2002 Crop Science Society of America.

Cell foundry with high product specificity and catalytic activity for 21-deoxycortisol biotransformation.

PubMed

Xiong, Shuting; Wang, Ying; Yao, Mingdong; Liu, Hong; Zhou, Xiao; Xiao, Wenhai; Yuan, Yingjin

2017-06-13

21-deoxycortisol (21-DF) is the key intermediate to manufacture pharmaceutical glucocorticoids. Recently, a Japan patent has realized 21-DF production via biotransformation of 17-hydroxyprogesterone (17-OHP) by purified steroid 11β-hydroxylase CYP11B1. Due to the less costs on enzyme isolation, purification and stabilization as well as cofactors supply, whole-cell should be preferentially employed as the biocatalyst over purified enzymes. No reports as so far have demonstrated a whole-cell system to produce 21-DF. Therefore, this study aimed to establish a whole-cell biocatalyst to achieve 21-DF transformation with high catalytic activity and product specificity. In this study, Escherichia coli MG1655(DE3), which exhibited the highest substrate transportation rate among other tested chassises, was employed as the host cell to construct our biocatalyst by co-expressing heterologous CYP11B1 together with bovine adrenodoxin and adrenodoxin reductase. Through screening CYP11B1s (with mutagenesis at N-terminus) from nine sources, Homo sapiens CYP11B1 mutant (G25R/G46R/L52 M) achieved the highest 21-DF transformation rate at 10.6 mg/L/h. Furthermore, an optimal substrate concentration of 2.4 g/L and a corresponding transformation rate of 16.2 mg/L/h were obtained by screening substrate concentrations. To be noted, based on structural analysis of the enzyme-substrate complex, two types of site-directed mutations were designed to adjust the relative position between the catalytic active site heme and the substrate. Accordingly, 1.96-fold enhancement on 21-DF transformation rate (to 47.9 mg/L/h) and 2.78-fold improvement on product/by-product ratio (from 0.36 to 1.36) were achieved by the combined mutagenesis of F381A/L382S/I488L. Eventually, after 38-h biotransformation in shake-flask, the production of 21-DF reached to 1.42 g/L with a yield of 52.7%, which is the highest 21-DF production as known. Heterologous CYP11B1 was manipulated to construct E. coli biocatalyst converting 17-OHP to 21-DF. Through the strategies in terms of (1) screening enzymes (with N-terminal mutagenesis) sources, (2) optimizing substrate concentration, and most importantly (3) rational design novel mutants aided by structural analysis, the 21-DF transformation rate was stepwise improved by 19.5-fold along with 4.67-fold increase on the product/byproduct ratio. Eventually, the highest 21-DF reported production was achieved in shake-flask after 38-h biotransformation. This study highlighted above described methods to obtain a high efficient and specific biocatalyst for the desired biotransformation.

The importance of measuring toothpaste abrasivity in both a quantitative and qualitative way

PubMed Central

Tellefsen, Georg; Johannsen, Annsofi; Liljeborg, Anders

2013-01-01

Objective. To evaluate the relative abrasivity of different toothpastes and polishing pastes both qualitatively and quantitatively. Materials and methods. Acrylic plates were exposed to brushing in a brushing machine with a toothpaste/water slurry for 1 and 6 h. Twelve different toothpastes were used and also four different polishing pastes. The results were evaluated using a profilometer after 1 and 6 h of brushing (corresponding to 2000 and 12 000 double strokes, respectively). A surface roughness value (Ra-value) and also a volume loss value were calculated from the profilometer measurements. These values were then correlated to each other. An unpaired t-test for the difference in the abrasion values between the toothpastes and the abrasion values over time was used. Results. The polishing paste RDA® 170 yielded higher Ra-values than RDA 250®, both after 1 and 6 h of brushing (1.01 ± 0.22 and 8.99 ± 1.55 compared to 0.63 ± 0.26 and 7.83 ± 5.89, respectively) as well as volume loss values (3.71 ± 0.17 and 20.20 ± 2.41 compared to 2.15 ± 1.41 and 14.79 ± 11.76, respectively), thus poor correlations between the RDA and Ra and Volume loss values were shown. Among the toothpastes, Apotekets® showed the highest Ra value after 1 h of brushing and Pepsodent® whitening after 6 h of brushing. Pepsodent® whitening also showed the highest volume loss values, both after 1 and 6 h of brushing. Conclusion. This study emphasizes the importance of not only considering the RDA value, but also a roughness value, when describing the abrasivity of a toothpaste. Furthermore, it can be concluded that so called ‘whitening' toothpastes do not necessarily have a higher abrasive effect than other toothpastes. PMID:22746180

An NMR study of cobalt-catalyzed hydroformylation using para-hydrogen induced polarisation.

PubMed

Godard, Cyril; Duckett, Simon B; Polas, Stacey; Tooze, Robert; Whitwood, Adrian C

2009-04-14

The syntheses of Co(eta3-C3H5)(CO)2PR2R' (R, R' = Ph, Me; R, R' = Me, Ph; R = R' = Ph, Cy, CH2Ph) and Co(eta3-C3H5)(CO)(L) (L = dmpe and dppe) are described, and X-ray structures for Co(eta3-C3H5)(CO)(dppe) and the PPh2Me, PCy3 derivatives reported. The relative ability of Co(eta3-C3H5)(CO)2(PR2R') to exchange phosphine for CO follows the trend PMe2Ph < PPh2Me < PCy3 < P(CH2Ph)3 < PPh3. Reactions of the allyl complexes with para-hydrogen (p-H2) lead to the observation of para-hydrogen induced polarisation (PHIP) in both liberated propene and propane. Reaction of these complexes with both CO and H2 leads to the detection of linear acyl containing species Co(COCH2CH2CH3)(CO)3(PR2R') and branched acyl complexes Co(COCH(CH3)2)(CO)3(PR2R') via the PHIP effect. In the case of PPh2Me, additional signals for Co(COCH2CH2CH3)(CO)2(PPh2Me)(propene) and Co(COCH(CH3)2)(CO)2(PPh2Me)(propene) are also detected. When the reactions of H2 and diphenylacetylene are studied with the same precursor, Co(CO)3(PPh2Me)(CHPhCH2Ph) is seen. Studies on how the appearance and ratio, of the PHIP enhanced signals vary as a function of reaction temperature and H2 : CO ratio are reported. These profiles are used to learn about the mechanism of catalysis and reveal how the rates of key steps leading to linear and branched hydroformylation products vary with the phosphine. These data also reveal that the PMe2Ph and PPh2Me based systems yield the highest selectivity for linear hydroformylation products.

Oligonucleofide Imprinting in Aqueous Environment

DTIC Science & Technology

2002-04-05

C j (Scheme 1) [8]. The coupling of individually protected nucleotides H 0 1 using a phosphoramidite linkage yields phosphite 2. This linkage is later...4 2As, As` Telrazole OBz •- DMTrOJ-O- " DMT P- OBzOR 70% OR 6 R = CH2 CH2CN 7 8 Phosphite 8 was then oxidized using 12 to yield phosphate 9[ 10]. The...Monomer Monomer(s) Yields P1 P10 1""’k% ,,"" Q 95/573 S~95/5 P1i P10 -XH MeOH/H 20 P2 P20 J.ýN.y 95/5 40 %P2 P20 H20/MeOH P3 P30 >.N. MeOH/H20 60 % P4* P40

Statistical optimization of medium components for avilamycin production by Streptomyces viridochromogenes Tü57-1 using response surface methodology.

PubMed

Zhu, Chuan-He; Lu, Fu-Ping; He, Ya-Nan; Zhang, Juan-Kun; Du, Lian-Xiang

2007-04-01

A fermentation medium for avilamycin production by Streptomyces viridochromogenes Tü57-1 has been optimized. Important components and their concentrations were investigated using fractional factorial design and Box-Behnken Design. The results showed that soybean flour, soluble starch, MgSO4.7H2O and CaCl2.2H2O are important for avilamycin production. A polynomial model related to medium components and avilamycin yield had been established. A high coefficient of determination (R2 = 0.92) was obtained that indicated good agreement between the experimental and predicted values of avilamycin yield. Student's T-test of each coefficient showed that all the linear and quadratic terms had significant effect (P > |T| < 0.05) on avilamycin yield. The significance of tested components was related to MgSO4.7H2O (0.37 g/L), CaCl2.2H2O (0.39 g/L), soybean flour (21.97 g/L) and soluble starch (37.22 g/L). The yield of avilamycin reached 88.33 +/- 0.94 mg/L (p < 0.05) that was 2.8-fold the initial yield.

Design, synthesis and biological evaluation of novel quinazoline-2,4-diones conjugated with different amino acids as potential chitin synthase inhibitors.

PubMed

Noureldin, Nada A; Kothayer, Hend; Lashine, El-Sayed M; Baraka, Mohamed M; Huang, Yanrong; Li, Bing; Ji, Qinggang

2018-05-25

A series of (2-(1-methyl-2,4-dioxo-1,2-dihydroquinazolin-3(4H)-yl) acetamido) acids) (6 a-m), (7) has been designed to inhibit the action of fungus chitin synthase enzyme (CHS). The synthesis of the designed compounds was carried out in four steps starting from the reaction between 1-methylquinazoline-2,4(1H,3H)-dione and ethyl chloroacetate to yield the ethyl acetate derivative. This ester was hydrolyzed to the corresponding carboxylic acid derivative that was then utilized to couple several amino acids getting the final designed compounds. The synthesized compounds were tested for their inhibition against CHS. Compound 7 showed the highest potency among others with minimum inhibitory concentration (IC 50 ) of 0.166 mmol/L, while polyoxin B (the positive control) had IC 50 of 0.17 mmol/L. The synthesized compounds were also evaluated for their in vitro antifungal activity using Aspergillus fumigates, Aspergillus flavus, Crytococcus neoformans and Candida albicans. Unfortunately, the 14 synthesized compounds showed lower in vitro activity compared to the used active controls. However, compound 6m and fluconazole have synergistic effect on Aspergillus flavus; Compounds 7 and fluconazole have synergistic effects on Aspergillus fumigates. Copyright © 2018 Elsevier Masson SAS. All rights reserved.

High-yield hydrogen production from biomass by in vitro metabolic engineering: Mixed sugars coutilization and kinetic modeling

PubMed Central

Rollin, Joseph A.; Martin del Campo, Julia; Myung, Suwan; Sun, Fangfang; You, Chun; Bakovic, Allison; Castro, Roberto; Chandrayan, Sanjeev K.; Wu, Chang-Hao; Adams, Michael W. W.; Senger, Ryan S.; Zhang, Y.-H. Percival

2015-01-01

The use of hydrogen (H2) as a fuel offers enhanced energy conversion efficiency and tremendous potential to decrease greenhouse gas emissions, but producing it in a distributed, carbon-neutral, low-cost manner requires new technologies. Herein we demonstrate the complete conversion of glucose and xylose from plant biomass to H2 and CO2 based on an in vitro synthetic enzymatic pathway. Glucose and xylose were simultaneously converted to H2 with a yield of two H2 per carbon, the maximum possible yield. Parameters of a nonlinear kinetic model were fitted with experimental data using a genetic algorithm, and a global sensitivity analysis was used to identify the enzymes that have the greatest impact on reaction rate and yield. After optimizing enzyme loadings using this model, volumetric H2 productivity was increased 3-fold to 32 mmol H2⋅L−1⋅h−1. The productivity was further enhanced to 54 mmol H2⋅L−1⋅h−1 by increasing reaction temperature, substrate, and enzyme concentrations—an increase of 67-fold compared with the initial studies using this method. The production of hydrogen from locally produced biomass is a promising means to achieve global green energy production. PMID:25848015

Evaluation of clinical methods for diagnosing bacterial vaginosis.

PubMed

Gutman, Robert E; Peipert, Jeffrey F; Weitzen, Sherry; Blume, Jeffrey

2005-03-01

To determine whether the current clinical criteria for diagnosing bacterial vaginosis can be simplified by using 2 clinical criteria rather than the standard 3 of 4 criteria (Amsel's criteria). This was a prospective observational study of 269 women undergoing a vaginal examination in the Women's Primary Care Center, Division of Research, or Colposcopy Clinic at Women & Infants Hospital. All 4 clinical criteria for diagnosing bacterial vaginosis were collected, and Gram stain was used as the gold standard. Sensitivity and specificity were calculated for each individual criterion, combinations of criteria, and a colorimetric pH and amine card. Receiver operating characteristic curve was generated to estimate the preferred pH and percentage of clue cells for diagnosing bacterial vaginosis. The prevalence of bacterial vaginosis in our study population was 38.7%. Vaginal pH was the most sensitive of all the criteria, at 89%, and a positive amine odor was the individual criteria with the highest specificity, at 93%. Similar specificity was seen with combinations of 2 criteria and Amsel's criteria. Receiver operating characteristic curve analysis yielded a preferred pH and percentage of clue cells of 5.0 and 20%, respectively. However, a pH of 4.5 or greater improves sensitivity with minimal loss of specificity. The clinical criteria for diagnosing bacterial vaginosis can be simplified to 2 clinical criteria without loss of sensitivity and specificity.

Electricity and H2 generation from hemicellulose by sequential fermentation and microbial fuel/electrolysis cell

NASA Astrophysics Data System (ADS)

Yan, Di; Yang, Xuewei; Yuan, Wenqiao

2015-09-01

Electricity and hydrogen generation by bacteria Geobacter sulfurreducens in a dual-chamber microbial fuel/electrolysis cell following the fermentation of hemicellulose by bacteria Moorella thermoacetica was investigated. Experimental results showed that 10 g l-1 xylose under 60 °C was appropriate for the fermentation of xylose by M. thermoacetica, yielding 0.87 g-acetic acid per gram of xylose consumed. Corncob hydrolysate could also be fermented to produce acetic acid, but with lower yield (0.74 g-acid per g-xylose). The broths of xylose and corncob hydrolysate fermented by M. thermoacetica containing acetic acid were fed to G. sulfurreducens in a dual-chamber microbial fuel/electrolysis cell for electricity and hydrogen generation. The highest open-circuit cell voltages generated were 802 and 745 mV, and hydrogen yields were 41.7 and 23.3 mmol per mol-acetate, in xylose and corncob hydrolysate fermentation broth media, respectively. The internal resistance of the microbial fuel/electrolysis cell fed with corncob hydrolysate fermentation broth (3472 Ω) was much higher than that with xylose fermentation broth (1993 Ω) or sodium acetate medium (467 Ω), which was believed to be the main cause of the variation in hydrogen yield of the three feeding media.

Effect of adding brewery wastewater to pulp and paper mill effluent to enhance the photofermentation process: wastewater characteristics, biohydrogen production, overall performance, and kinetic modeling.

PubMed

Hay, Jacqueline Xiao Wen; Wu, Ta Yeong; Juan, Joon Ching; Md Jahim, Jamaliah

2017-04-01

Although a significant amount of brewery wastewater (BW) is generated during beer production, the nutrients in the BW could be reused as a potential bio-resource for biohydrogen production. Therefore, improvements in photofermentative biohydrogen production due to a combination of BW and pulp and paper mill effluent (PPME) as a mixed production medium were investigated comprehensively in this study. The experimental results showed that both the biohydrogen yield and the chemical oxygen demand removal were improved through the combination of BW and PPME. The best biohydrogen yield of 0.69 mol H 2 /L medium was obtained using the combination of 10 % BW + 90 % PPME (10B90P), while the reuse of the wastewater alone (100 % BW and 100 % PPME) resulted in 42.3 and 44.0 % less biohydrogen yields than the highest yield, respectively. The greatest light efficiency was 1.97 % and was also achieved using the combination of both wastewaters at 10B90P. This study revealed the potential of reusing and combining two different effluents together, in which the combination of BW and PPME improved the nutrients and light penetration into the mixed production medium.

Influence of Nutritional Conditions on Production of l-Glutamine by Flavobacterium rigense

PubMed Central

Nabe, Koichi; Ujimaru, Toshihiko; Yamada, Shigeki; Chibata, Ichiro

1981-01-01

The nutritional conditions for the production of l-glutamine by Flavobacterium rigense strain 703 were investigated. The optimum concentration of ammonia for achieving the highest yield of l-glutamine (25 mg/ml of broth) was relatively broad, from 0.9 to 1.6%, whereas fumaric acid had a narrow optimum range, near 5.5%. High concentration of inorganic ions such as chloride or sulfate ion clearly inhibited cell growth. Therefore, ammonium salts other than (NH4)2-fumarate were unsuitable for the highest production. The optimum concentration of (NH4)2-fumarate was 7%. To reduce the concentration of fumaric acid in the medium, many substances were evaluated as substitutes. The fumaric acid concentration required for highest l-glutamine yield could not be replaced by any one of the compounds tested. However, part of fumaric acid could be replaced with succinic acid and cupric ion; 4% (NH4)2-fumarate plus 2.5% succinic acid or 5% (NH4)2-fumarate plus 1 mM cupric ion produced results similar to 7% (NH4)2-fumarate in the fermentation medium. PMID:16345682

Effect of dose rate on residual γ-H2AX levels and frequency of micronuclei in X-irradiated mouse lymphocytes.

PubMed

Turner, H C; Shuryak, I; Taveras, M; Bertucci, A; Perrier, J R; Chen, C; Elliston, C D; Johnson, G W; Smilenov, L B; Amundson, S A; Brenner, D J

2015-03-01

The biological risks associated with low-dose-rate (LDR) radiation exposures are not yet well defined. To assess the risk related to DNA damage, we compared the yields of two established biodosimetry end points, γ-H2AX and micronuclei (MNi), in peripheral mouse blood lymphocytes after prolonged in vivo exposure to LDR X rays (0.31 cGy/min) vs. acute high-dose-rate (HDR) exposure (1.03 Gy/min). C57BL/6 mice were total-body irradiated with 320 kVP X rays with doses of 0, 1.1, 2.2 and 4.45 Gy. Residual levels of total γ-H2AX fluorescence in lymphocytes isolated 24 h after the start of irradiation were assessed using indirect immunofluorescence methods. The terminal deoxynucleotidyl transferase dUTP nick end labeling (TUNEL) assay was used to determine apoptotic cell frequency in lymphocytes sampled at 24 h. Curve fitting analysis suggested that the dose response for γ-H2AX yields after acute exposures could be described by a linear dependence. In contrast, a linear-quadratic dose-response shape was more appropriate for LDR exposure (perhaps reflecting differences in repair time after different LDR doses). Dose-rate sparing effects (P < 0.05) were observed at doses ≤2.2 Gy, such that the acute dose γ-H2AX and TUNEL-positive cell yields were significantly larger than the equivalent LDR yields. At the 4.45 Gy dose there was no difference in γ-H2AX expression between the two dose rates, whereas there was a two- to threefold increase in apoptosis in the LDR samples compared to the equivalent 4.45 Gy acute dose. Micronuclei yields were measured at 24 h and 7 days using the in vitro cytokinesis-blocked micronucleus (CBMN) assay. The results showed that MNi yields increased up to 2.2 Gy with no further increase at 4.45 Gy and with no detectable dose-rate effect across the dose range 24 h or 7 days post exposure. In conclusion, the γ-H2AX biomarker showed higher sensitivity to measure dose-rate effects after low-dose LDR X rays compared to MNi formation; however, confounding factors such as variable repair times post exposure, increased cell killing and cell cycle block likely contributed to the yields of MNi with accumulating doses of ionizing radiation.

Combinations of Aromatic and Aliphatic Radiolysis.

PubMed

LaVerne, Jay A; Dowling-Medley, Jennifer

2015-10-08

The production of H(2) in the radiolysis of benzene, methylbenzene (toluene), ethylbenzene, butylbenzene, and hexylbenzene with γ-rays, 2-10 MeV protons, 5-20 MeV helium ions, and 10-30 MeV carbon ions is used as a probe of the overall radiation sensitivity and to determine the relative contributions of aromatic and aliphatic entities in mixed hydrocarbons. The addition of an aliphatic side chain with progressively from one to six carbon lengths to benzene increases the H(2) yield with γ-rays, but the yield seems to reach a plateau far below that found from a simple aliphatic such as cyclohexane. There is a large increase in H(2) with LET (linear energy transfer) for all of the substituted benzenes, which indicates that the main process for H(2) formation is a second-order process and dominated by the aromatic entity. The addition of a small amount of benzene to cyclohexane can lower the H(2) yield from the value expected from a simple mixture law. A 50:50% volume mixture of benzene-cyclohexane has essentially the same H(2) yield as cyclohexylbenzene at a wide variation in LET, suggesting that intermolecular energy transfer is as efficient as intramolecular energy transfer.

Effects of p-chlorophenoxyisobutyric acid, arabinogalactan, and activated charcoal on microspore embryogenesis in kale.

PubMed

Niu, R Q; Zhang, Y; Tong, Y; Liu, Z Y; Wang, Y H; Feng, H

2015-04-27

To improve embryogenesis in microspore cultures of kale (Brassica oleracea L. var. acephala DC.), 6-benzylaminopurine (6-BA), naphthaleneacetic acid (NAA), arabinogalactan (AG), p-chlorophenoxyisobutyric acid (PCIB), and activated charcoal (AC) were added to the medium using four varieties of kale. The results showed that the addition of AG (0.1-0.2 g/L), AC (0.1-0.2 g/L) or a combination of 6-BA (0.1-0.2 mg/L) and NAA (0.1-0.2 mg/L) promoted embryo-genesis. Adding 40 μM PCIB or a combination of 40 μM PCIB and 0.2 g/L AC to NLN-13 medium at pH 5.8 effectively enhanced embryogenesis. Treatment with a combination of 40 μM PCIB and 10 mg/L AG gave the highest rate of embryonic induction, especially in genotype "Y007," which showed a twelve-fold increase in yield.

2,3-Butanediol recovery from fermentation broth by alcohol precipitation and vacuum distillation.

PubMed

Jeon, Sangjun; Kim, Duk-Ki; Song, Hyohak; Lee, Hee Jong; Park, Sunghoon; Seung, Doyoung; Chang, Yong Keun

2014-04-01

This study presents a new and effective downstream process to recover 2,3-butanediol (2,3-BD) from fermentation broth which is produced by a recombinant Klebsiella pneumoniae strain. The ldhA-deficient K. pneumoniae strain yielded about 90 g/L of 2,3-BD, along with a number of by-products, such as organic acids and alcohols, in a 65 h fed-batch fermentation. The pH-adjusted cell-free fermentation broth was firstly concentrated until 2,3-BD reached around 500 g/L by vacuum evaporation at 50°C and 50 mbar vacuum pressure. The concentrated solution was further treated using light alcohols, including methanol, ethanol, and isopropanol, for the precipitation of organic acids and inorganic salts. Isopropanol showed the highest removal efficiency, in which 92.5% and 99.8% of organic acids and inorganic salts were precipitated, respectively. At a final step, a vacuum distillation process enabled the recovery of 76.2% of the treated 2,3-BD, with 96.1% purity, indicating that fermentatively produced 2,3-BD is effectively recovered by a simple alcohol precipitation and vacuum distillation. Copyright © 2013 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.