Urban Pollutant Transport and Infiltration into Buildings Using Perfluorocarbon Tracers.

PubMed

Matthews, James C; Bacak, Asan; Khan, M Anwar H; Wright, Matthew D; Priestley, Michael; Martin, Damien; Percival, Carl J; Shallcross, Dudley E

2017-02-21

People spend the majority of their time indoors and therefore the quality of indoor air is worthy of investigation; indoor air quality is affected by indoor sources of pollutants and from pollutants entering buildings from outdoors. In this study, unique perfluorocarbon tracers were released in five experiments at a 100 m and ~2 km distance from a large university building in Manchester, UK and tracer was also released inside the building to measure the amount of outdoor material penetrating into buildings and the flow of material within the building itself. Air samples of the tracer were taken in several rooms within the building, and a CO₂ tracer was used within the building to estimate air-exchange rates. Air-exchange rates were found to vary between 0.57 and 10.90 per hour. Indoor perfluorocarbon tracer concentrations were paired to outdoor tracer concentrations, and in-out ratios were found to vary between 0.01 and 3.6. The largest room with the lowest air-exchange rate exhibited elevated tracer concentrations for over 60 min after the release had finished, but generally had the lowest concentrations, the room with the highest ventilation rates had the highest concentration over 30 min, but the peak decayed more rapidly. Tracer concentrations indoors compared to outdoors imply that pollutants remain within buildings after they have cleared outside, which must be considered when evaluating human exposure to outdoor pollutants.

Urban Pollutant Transport and Infiltration into Buildings Using Perfluorocarbon Tracers

PubMed Central

Matthews, James C.; Bacak, Asan; Khan, M. Anwar H.; Wright, Matthew D.; Priestley, Michael; Martin, Damien; Percival, Carl J.; Shallcross, Dudley E.

2017-01-01

People spend the majority of their time indoors and therefore the quality of indoor air is worthy of investigation; indoor air quality is affected by indoor sources of pollutants and from pollutants entering buildings from outdoors. In this study, unique perfluorocarbon tracers were released in five experiments at a 100 m and ~2 km distance from a large university building in Manchester, UK and tracer was also released inside the building to measure the amount of outdoor material penetrating into buildings and the flow of material within the building itself. Air samples of the tracer were taken in several rooms within the building, and a CO2 tracer was used within the building to estimate air-exchange rates. Air-exchange rates were found to vary between 0.57 and 10.90 per hour. Indoor perfluorocarbon tracer concentrations were paired to outdoor tracer concentrations, and in-out ratios were found to vary between 0.01 and 3.6. The largest room with the lowest air-exchange rate exhibited elevated tracer concentrations for over 60 min after the release had finished, but generally had the lowest concentrations, the room with the highest ventilation rates had the highest concentration over 30 min, but the peak decayed more rapidly. Tracer concentrations indoors compared to outdoors imply that pollutants remain within buildings after they have cleared outside, which must be considered when evaluating human exposure to outdoor pollutants. PMID:28230812

[Effects of nitrogen application rates and straw returning on nutrient balance and grain yield of late sowing wheat in rice-wheat rotation].

PubMed

Zhang, Shan; Shi, Zu-liang; Yang, Si-jun; Gu, Ke-jun; Dai, Ting-bo; Wang, Fei; Li, Xiang; Sun, Ren-hua

2015-09-01

Field experiments were conducted to study the effects of nitrogen application rates and straw returning on grain yield, nutrient accumulation, nutrient release from straw and nutrient balance in late sowing wheat. The results showed that straw returning together with appropriate application of nitrogen fertilizer improved the grain yield. Dry matter, nitrogen, phosphorus and potassium accumulation increased significantly as the nitrogen application rate increased. At the same nitrogen application rate (270 kg N · hm(-2)), the dry matter, phosphorus and potassium accumulation of the treatment with straw returning were higher than that without straw returning, but the nitrogen accumulation was lower. Higher-rate nitrogen application promoted straw decomposition and nutrient release, and decreased the proportion of the nutrient released from straw after jointing. The dry matter, phosphorus and potassium release from straw showed a reverse 'N' type change with the wheat growing, while nitrogen release showed a 'V' type change. The nutrient surplus increased significantly with the nitrogen application rate. At the nitrogen application rate for the highest grain yield, nitrogen and potassium were surplus significantly, and phosphorus input could keep balance. It could be concluded that as to late sowing wheat with straw returning, applying nitrogen at 257 kg · hm(-2) and reducing potassium fertilizer application could improve grain yield and reduce nutrients loss.

Development and characterization of different black raspberry confection matrices designed for delivery of phytochemicals.

PubMed

Gu, Junnan; Ahn-Jarvis, Jennifer H; Vodovotz, Yael

2015-03-01

Three forms of confections containing black raspberries (BRB) powder were developed to provide controlled release of phytochemicals for oral disease prevention. Our objective was to investigate the impact of varying confection matrices on the release rate of BRB phytochemicals. Confections were developed and prepared. Textural properties of confections were analyzed, compared and correlated with the release rate of phytochemicals from BRB confections with in vitro dissolution test. In the results, BRB content reached 22% in hard candy and pectin-based confections and 40% in starch-based confections, respectively. Pectin- and starch-based confections retained >93% of its original anthocyanins after processing while hard candy had 59%. Starch confections showed higher G' in rheological analysis and higher hardness but lower cohesiveness and springiness in textural profile analysis than pectin confections (P < 0.05). The confection types showed different microstructure with scanning electronic microscopy (SEM). Corresponding to their physicochemical properties, confections showed fast (hard candy), intermediate (pectin confections), and slow (starch confections) release rates with a final releasing time of 90, 150, and 540 min in dissolution studies. Three confections were rated between neither like nor dislike to like slightly (n = 60). Pectin confections had the highest overall acceptance (like slightly) and 62% of subjects rated this type of confection as the most liked ones. These results indicate that delivery matrix could modulate the phytochemical release rate from BRB confection and also influence sensory preference. © 2015 Institute of Food Technologists®

The effect of methylcellulose on metronidazole release from polyacrylic acid hydrogels.

PubMed

Musial, Witold

2007-08-01

Topical treatment of acne rosacea, a chronic condition characterized by recurrent course for many years, is primarily based on metronidazole preparations. The aim of this study was to evaluate the effect of various acrylic acid polymers, in composition with methylcellulose on metronidazole release rate from hydrogels proposed for the treatment of acne rosacea. Viscosity and release studies using "Paddle over Disk" system with semipermeable membrane of MWCO 3500 were performed. Compositions of Carbopol 971P and methylcellulose revealed an increase in viscosity with increasing concentration of methylcellulose in the range of 17200-26166 mPa.s. In all the examined formulations, the release process was characterized by a two-stage course. Among bipolymeric formulations, the highest first-stage release rate of 9.18 x 10(-3) min(-1) was determined for the gel consisting of 2.00% Carbopol 980NF with 1.00% methylcellulose. The second-stage release rates ranged between 2.88 x 10(-3) and 8.00 x 10(-3) min(-1). Two-stage release course can thus be attributed to metronidazole distribution into two compartments of hydrogel matrix. Proposed gels, with similar rheological properties, may be used for ex vivo and in vivo studies to obtain a suitable drug activity of metronidazole in the treatment of acne rosacea.

[The effects of various factors on the in vitro velocity of drug release from repository tablets. Part 4: Isoniazid (Rimicid) respository tablets (author's transl)].

PubMed

Tomassini, L; Michailova, D; Naplatanova, D; Slavtschev, P

1979-12-01

The authors investigated the release of isoniazid from repository tablets as related to form, processing technology, strength constant and storage for 5 years. On determining the diffusion coefficient (D), the initial dissolution rate (Vo) and the time required for the diffusion of the releasing medium to the middle of the tablet (t1/2), it was found that the difference in release rate between the flat and the biconvex tablets is small. Furthermore, it was stated that the three-layer tablets have very high D and Vo values and very low t1/2 values, for what reason they are unsuited for repository tablets of the composition under investigation. Moreover, it was found that an increase of the strength constant does not affect the D, t1/2 and Vo values, and that the release of isoniazid is retarded only in flat tablets with the highest strength constant. Storage exerts no effect on the drug release from these tablets. The industrial production of these tablets is under way.

Release of paclitaxel from polylactide-co-glycolide (PLGA) microparticles and discs under irradiation.

PubMed

Wang, J; Ng, C W; Win, K Y; Shoemakers, P; Lee, T K Y; Feng, S S; Wang, C H

2003-01-01

Paclitaxel is a promising anti-cancer drug as well as a radiosensitizer for chemotherapy and radiotherapy applications. Because of the poor solubility of paclitaxel in water and most pharmaceutical reagents, it is usually formulated with an adjuvant called Cremophor EL, which causes severe side effects. This work develops new dosage forms of paclitaxel for controlled release application, which do not require the adjuvant and, thus, can avoid its associated side effects. Paclitaxel was encapsulated into the PLGA matrix with various additives such as polyethylene glycol (PEG), isopropyl myristate (IPM) and d-alpha tocopheryl polyethylene glycol (Vitamin E TPGS). These additives were used to enhance the release rate of paclitaxel from the polymer matrix. Spray-drying and an hydraulic press were used to prepare paclitaxel-PLGA microspheres and discs. The microspheres and discs were given different irradiation doses to investigate their effects on the surface morphology (characterized by SEM, AFM and XPS) and in vitro release properties. There seems to be a small effect of the ionizing radiation on various formulations. Although the irradiation did not cause observable changes on the morphology of the polymer matrix, the release rate can be enhanced by a few per cent. It was found that PEG has the highest enhancement effect for release rate among all the additives investigated in this study.

Passive air sampling using semipermeable membrane devices at different wind-speeds in situ calibrated by performance reference compounds.

PubMed

Söderström, Hanna S; Bergqvist, Per-Anders

2004-09-15

Semipermeable membrane devices (SPMDs) are passive samplers used to measure the vapor phase of organic pollutants in air. This study tested whether extremely high wind-speeds during a 21-day sampling increased the sampling rates of polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs), and whether the release of performance reference compounds (PRCs) was related to the uptakes at different wind-speeds. Five samplers were deployed in an indoor, unheated, and dark wind tunnel with different wind-speeds at each site (6-50 m s(-1)). In addition, one sampler was deployed outside the wind tunnel and one outside the building. To test whether a sampler, designed to reduce the wind-speeds, decreased the uptake and release rates, each sampler in the wind tunnel included two SPMDs positioned inside a protective device and one unprotected SPMD outside the device. The highest amounts of PAHs and PCBs were found in the SPMDs exposed to the assumed highest wind-speeds. Thus, the SPMD sampling rates increased with increasing wind-speeds, indicating that the uptake was largely controlled by the boundary layer at the membrane-air interface. The coefficient of variance (introduced by the 21-day sampling and the chemical analysis) for the air concentrations of three PAHs and three PCBs, calculated using the PRC data, was 28-46%. Thus, the PRCs had a high ability to predict site effects of wind and assess the actual sampling situation. Comparison between protected and unprotected SPMDs showed that the sampler design reduced the wind-speed inside the devices and thereby the uptake and release rates.

Release of lysosomal enzymes in Candida albicans phagocytosis by rat peritoneal macrophages.

PubMed

Fontenla de Petrino, S E; Sirena, A

1984-02-15

The present paper reports the in vitro release of lysosomal enzymes in the supernatant of cultures of rat peritoneal macrophages, with the addition of Candida albicans cells. Macrophages were taken from the rat peritoneal cavity 72 hr after non-specific activation with Brain-Heart-Infusion (B.H.I.) broth containing 10% proteose-peptone No. 3. They were then cultured in Parker medium No. 199 (TC 199). After 24 hr a suspension of Candida albicans cells, in a determined concentration, was added to the peritoneal macrophage cultures. At that time, and during pre-determined periods, the following enzymes in the culture supernatants were studied using colorimetric methods: beta-glucuronidase, beta-galactosidase and acid phosphatase. It is concluded that, under identical conditions, the release of beta-galactosidase and acid phosphatase is higher than for beta-glucuronidase. The release rate of all three enzymes is the highest at a 6 hr incubation period, after which, a gradual decrease leads to the rate down to 50% at 24 hr.

Effect of water-column pH on sediment-phosphorus release rates in Upper Klamath Lake, Oregon, 2001

USGS Publications Warehouse

Fisher, Lawrence H.; Wood, Tamara M.

2004-01-01

Sediment-phosphorus release rates as a function of pH were determined in laboratory experiments for sediment and water samples collected from Shoalwater Bay in Upper Klamath Lake, Oregon, in 2001. Aerial release rates for a stable sediment/water interface that is representative of the sediment surface area to water column volume ratio (1:3) observed in the lake and volumetric release rates for resuspended sediment events were determined at three different pH values (8.1, 9.2, 10.2). Ambient water column pH (8.1) was maintained by sparging study columns with atmospheric air. Elevation of the water column pH to 9.2 was achieved through the removal of dissolved carbon dioxide by sparging with carbon dioxide-reduced air, partially simulating water chemistry changes that occur during algal photosynthesis. Further elevation of the pH to 10.2 was achieved by the addition of sodium hydroxide, which doubled average alkalinities in the study columns from about 1 to 2 milliequivalents per liter. Upper Klamath Lake sediments collected from the lake bottom and then placed in contact with lake water, either at a stable sediment/water interface or by resuspension, exhibited an initial capacity to take up soluble reactive phosphorus (SRP) from the water column rather than release phosphorus to the water column. At a higher pH this initial uptake of phosphorus is slowed, but not stopped. This initial phase was followed by a reversal in which the sediments began to release SRP back into the water column. The release rate of phosphorus 30 to 40 days after suspension of sediments in the columns was 0.5 mg/L/day (micrograms per liter per day) at pH 8, and 0.9 mg/L/day at pH 10, indicating that the higher pH increased the rate of phosphorus release by a factor of about two. The highest determined rate of release was approximately 10% (percent) of the rate required to explain the annual internal loading to Upper Klamath Lake from the sediments as calculated from a lake-wide mass balance and observed in total phosphorus data collected at individual locations.

Growth, smoltification, and smolt-to-adult return of spring chinook salmon from hatcheries on the Deschutes river, Oregon

USGS Publications Warehouse

Beckman, B.R.; Dickhoff, Walton W.; Zaugg, W.S.; Sharpe, C.; Hirtzel, S.; Schrock, R.; Larsen, D.A.; Ewing, R.D.; Palmisano, A.; Schreck, C.B.; Mahnken, C.V.W.

1999-01-01

The relationship between smoltification and smolt-to-adult return (SAR) of spring chinook salmon Oncorhynchus tshawytscha from the Deschutes River, Oregon, was examined for four release groups in each of three successive years. Fish were reared, marked with coded wire tags, and released from Round Butte Hatchery, Pelton Ladder rearing facility, and Warm Springs National Fish Hatchery. Smolt releases occurred in nearly the same place at similar times, allowing a direct comparison of SAR to several characters representing smolt quality. Return rates varied significantly among facilities, varying over an order of magnitude each year. The highest average SAR was from Pelton Ladder, the lowest was from Warm Springs. Each of the characters used as metrics of smoltification - fish size, spring growth rate (February-April), condition factor, plasma hormone concentration (thyroxine, cortisol, and insulin-like growth factor-I [IGF-I]), stress challenge, gill Na+,K+-ATPase activity, and liver glycogen concentration - varied significantly among facilities and seasonally within hatchery groups. However, only spring growth rate, gill ATPase activity, and plasma IGF-I concentration showed significant relationships to SAR. These characters and SAR itself were consistently lower for fish released from Warm Springs Hatchery than for fish from Round Butte Hatchery and Pelton Ladder. This demonstrates that differences in the quality of fish released by facilities may have profound effects on subsequent survival and suggests that manipulations of spring growth rate may be used to influence the quality of smolts released from facilities.

Characterizing and comparing seismicity at Cascade Range (USA) volcanoes

NASA Astrophysics Data System (ADS)

Moran, S. C.; Thelen, W. A.

2010-12-01

The Cascade Range includes 13 volcanic systems across Washington, Oregon, and northern California that are considered to have the potential to erupt at any time, including two that have erupted in the last 100 years (Mount St. Helens (MSH) and Lassen Peak). We investigated how seismicity compares among these volcanoes, and whether the character of seismicity (rate, type, style of occurrence over time, etc.) is related to eruptive activity at the surface. Seismicity at Cascade volcanoes has been monitored by seismic networks of variable apertures, station densities, and lengths of operation, which makes a direct comparison of seismicity among volcanoes somewhat problematic. Here we present results of two non-network-dependent approaches to making such seismicity comparisons. In the first, we used network geometry and a grid-search method to compute the minimum magnitude required for a network to locate an earthquake (“theoretical location threshold”, defined as an event recorded on at least 4 stations with gap of <135o) for each volcano out to 7 km. We then selected earthquakes with magnitudes greater than the highest theoretical location threshold determined for any Cascade volcano. To account for improving network densities with time, we used M 2.1 (location threshold for the Three Sisters 1980s-90s network) for 1987-1999 and M 1.6 (threshold for the Crater Lake 2000s network) for 2000-2010. In order to include only background seismicity, we excluded earthquakes occurring at any volcano during the 2004-2008 MSH eruption. We found that Mount Hood, Lassen Peak, and MSH had the three highest seismicity rates over that period, with Mount Hood, Medicine Lake volcano, and MSH having the three highest cumulative seismic energy releases. The Medicine Lake energy release is dominated by a single swarm in September 1988; if that swarm is removed, then Lassen would have the third-highest cumulative seismic energy release. For the second comparison, we determined the degree of “swarminess” for seismicity at each volcano. We first determined the background rate of locatable earthquakes (no selection criteria were applied) within 7 km of each volcanic center, and then identified days during which the rate of seismicity was 2σ or more above the background rate. Above-background days were linked together into one swarm if they occurred within 5 days of each other. We found that seismicity dominantly occurs in swarms (>60% of located earthquakes) at Mount Hood, Three Sisters, Medicine Lake, and Lassen Peak, is mixed at Mount Rainier (46%), and dominantly does not occur in swarms (<40%) at MSH (non-eruptive periods only) and Mount Shasta. These comparisons show no obvious relationship with recency of eruptive activity, with the possible exception that volcanoes with the most recent eruptions have the highest background seismicity levels.

Enhancement of the release of azelaic acid through the synthetic membranes by inclusion complex formation with hydroxypropyl-beta-cyclodextrin.

PubMed

Manosroi, Jiradej; Apriyani, Maria Goretti; Foe, Kuncoro; Manosroi, Aranya

2005-04-11

The aim of this study was to investigate the release rates of azelaic acid and azelaic acid-hydroxypropyl-beta-cyclodextrin (HPbetaCD) inclusion complex through three types of synthetic membranes, namely cellophane, silicone and elastomer membranes. Solid inclusion complexes of azelaic acid-HPbetaCD at the molar ratio of 1:1 were prepared by coevaporation and freeze-drying methods, subsequently characterized by differential scanning calorimetry, X-ray diffractometry and dissolution studies. Solid inclusion complex obtained by coevaporation method which exhibited the inclusion of azelaic acid in the HPbetaCD cavity and gave the highest dissolution rate of azelaic acid was selected for the release study. Release studies of azelaic acid and this complex through the synthetic membranes were conducted using vertical Franz diffusion cells at 30 degrees C for 6 days. The release rates of azelaic acid through the synthetic membranes were enhanced by the formation of inclusion complex with HPbetaCD at the molar ratio of 1:1, with the increasing fluxes of about 41, 81 and 28 times of the uncomplexed system in cellophane, silicone and elastomer membranes, respectively. The result from this study can be applied for the development of azelaic acid for topical use.

Preparation and Characterization of Amylose Inclusion Complexes for Drug Delivery Applications.

PubMed

Carbinatto, Fernanda M; Ribeiro, Tatiana S; Colnago, Luiz Alberto; Evangelista, Raul Cesar; Cury, Beatriz S F

2016-01-01

Amylose complexes with nimesulide (NMS) and praziquantel (PZQ) were prepared by a simple and low cost method, so that high yield (>57%) and drug content (up to 68.16%) were achieved. The influence of drug:polymer ratio, temperature, and presence of palmitic acid on the complexes properties was evaluated. Differential scanning calorimetry, X-ray diffraction, and nuclear magnetic resonance data evidenced the drug-polymer interaction and the formation of inclusion complexes with semi-crystalline structures related to type II complexes. The drug release rates from complexes were lowered in acid media (pH 1.2) and phosphate buffer (pH 6.9). The presence of pancreatin promoted a significant acceleration of the release rates of both drugs, evidencing the enzymatic degradability of these complexes. The highest enzymatic resistance of PZQ1:30PA60°C complex makes the release time longer and the full release of PZQ in phosphate buffer with pancreatin occurred at 240 min, whereas the complexes with NMS and PZQ1:5PA90°C did it in 60 min. According to the Weibull model, the drug release process in media without enzyme occurred by complex mechanisms involving diffusion, swelling, and erosion. In media containing pancreatin, generally, the better correlation was with the first order, evidencing the acceleration of the release rates of drugs in the early stages of the test, due to enzymatic degradation.

Models to describe the thermal development rates of Cycloneda sanguinea L. (Coleoptera: Coccinelidae).

PubMed

Pachú, Jéssica Ks; Malaquias, José B; Godoy, Wesley Ac; de S Ramalho, Francisco; Almeida, Bruna R; Rossi, Fabrício

2018-04-01

Precise estimates of the lower (T min ) and higher (T max ) thermal thresholds as well as the temperature range that provides optimum performance (T opt ) enable to obtain the desired number of individuals in conservation systems, rearing and release of natural enemies. In this study, the relationship between the development rates of Cycloneda sanguinea L. (Coleoptera: Coccinelidae) and temperature was described using non-linear models developed by Analytis, Brière, Lactin, Lamb, Logan and Sharpe & DeMichele. There were differences between the models, considering the estimates of the parameters T min , T max , and T opt . All of the tested models were able to describe non-linear responses involving the development rates of C. sanguinea at constant temperatures. Lactin and Lamb gave the highest z weight for egg, while Analytis, Sharpe & DeMichele and Brière gave the highest values for larvae and pupae. The more realistic T opt estimated by the models varied from 29° to 31°C for egg, 27-28 °C for larvae and 28-29 °C for pupae. The Logan, Lactin and Analytis models estimated the T max for egg, larvae and pupae to be approximately 34 °C, while the T min estimated by the Analytis model was 16 °C for larvae and pupae. The information generated by our research will contribute towards improving the rearing and release of C. sanguinea in biological control programs, accurately controlling the rate of development in laboratory conditions or even scheduling the most favourable this species' release. Copyright © 2018 Elsevier Ltd. All rights reserved.

Effect of composition in the development of carbamazepine hot-melt extruded solid dispersions by application of mixture experimental design.

PubMed

Djuris, Jelena; Ioannis, Nikolakakis; Ibric, Svetlana; Djuric, Zorica; Kachrimanis, Kyriakos

2014-02-01

This study investigates the application of hot-melt extrusion for the formulation of carbamazepine (CBZ) solid dispersions, using polyethyleneglycol-polyvinyl caprolactam-polyvinyl acetate grafted copolymer (Soluplus, BASF, Germany) and polyoxyethylene-polyoxypropylene block copolymer (Poloxamer 407). In agreement with the current Quality by Design principle, formulations of solid dispersions were prepared according to a D-optimal mixture experimental design, and the influence of formulation composition on the properties of the dispersions (CBZ heat of fusion and release rate) was estimated. Prepared solid dispersions were characterized using differential scanning calorimetry, attenuated total reflectance infrared spectroscopy and hot stage microscopy, as well as by determination of the dissolution rate of CBZ from the hot-melt extrudates. Solid dispersions of CBZ can be successfully prepared using the novel copolymer Soluplus. Inclusion of Poloxamer 407 as a plasticizer facilitated the processing and decreased the hardness of hot-melt extrudates. Regardless of their composition, all hot-melt extrudates displayed an improvement in the release rate compared to the pure CBZ, with formulations having the ratio of CBZ : Poloxamer 407 = 1 : 1 showing the highest increase in CBZ release rate. Interactions between the mixture components (CBZ and polymers), or quadratic effects of the components, play a significant role in overall influence on the CBZ release rate. © 2013 Royal Pharmaceutical Society.

Iron oxide nanoparticle-based magnetic resonance method to monitor release kinetics from polymeric particles with high resolution.

PubMed

Chan, Minnie; Schopf, Eric; Sankaranarayanan, Jagadis; Almutairi, Adah

2012-09-18

A new method to precisely monitor rapid release kinetics from polymeric particles using super paramagnetic iron oxide nanoparticles, specifically by measuring spin-spin relaxation time (T(2)), is reported. Previously, we have published the formulation of logic gate particles from an acid-sensitive poly-β-aminoester ketal-2 polymer. Here, a series of poly-β-aminoester ketal-2 polymers with varying hydrophobicities were synthesized and used to formulate particles. We attempted to measure fluorescence of released Nile red to determine whether the structural adjustments could finely tune the release kinetics in the range of minutes to hours; however, this standard technique did not differentiate each release rate of our series. Thus, a new method based on encapsulation of iron oxide nanoparticles was developed, which enabled us to resolve the release kinetics of our particles. Moreover, the kinetics matched the relative hydrophobicity order determined by octanol-water partition coefficients. To the best of our knowledge, this method provides the highest resolution of release kinetics to date.

Summertime Acute Heat Illness in U.S. Emergency Departments from 2006 through 2010: Analysis of a Nationally Representative Sample

PubMed Central

Saha, Shubhayu; Luber, George

2014-01-01

Background: Patients with acute heat illness present primarily to emergency departments (EDs), yet little is known regarding these visits. Objective: We aimed to describe acute heat illness visits to U.S. EDs from 2006 through 2010 and identify factors associated with hospital admission or with death in the ED. Methods: We extracted ED case-level data from the Nationwide Emergency Department Sample (NEDS) for 2006–2010, defining cases as ED visits from May through September with any heat illness diagnosis (ICD-9-CM 992.0–992.9). We correlated visit rates and temperature anomalies, analyzed demographics and ED disposition, identified risk factors for adverse outcomes, and examined ED case fatality rates (CFR). Results: There were 326,497 (95% CI: 308,372, 344,658) cases, with 287,875 (88.2%) treated and released, 38,392 (11.8%) admitted, and 230 (0.07%) died in the ED. Heat illness diagnoses were first-listed in 68%. 74.7% had heat exhaustion, 5.4% heat stroke. Visit rates were highly correlated with annual temperature anomalies (Pearson correlation coefficient 0.882, p = 0.005). Treat-and-release rates were highest for younger adults (26.2/100,000/year), whereas hospitalization and death-in-the-ED rates were highest for older adults (6.7 and 0.03/100,000/year, respectively); all rates were highest in rural areas. Heat stroke had an ED CFR of 99.4/10,000 (95% CI: 78.7, 120.1) visits and was diagnosed in 77.0% of deaths. Adjusted odds of hospital admission or death in the ED were higher among elders, males, urban and low-income residents, and those with chronic conditions. Conclusions: Heat illness presented to the ED frequently, with highest rates in rural areas. Case definitions should include all diagnoses. Visit rates were correlated with temperature anomalies. Heat stroke had a high ED CFR. Males, elders, and the chronically ill were at greatest risk of admission or death in the ED. Chronic disease burden exponentially increased this risk. Citation: Hess JJ, Saha S, Luber G. 2014. Summertime acute heat illness in U.S. emergency departments from 2006 through 2010: analysis of a nationally representative sample. Environ Health Perspect 122:1209–1215; http://dx.doi.org/10.1289/ehp.1306796 PMID:24937159

Automated remote cameras for monitoring alluvial sandbars on the Colorado River in Grand Canyon, Arizona

USGS Publications Warehouse

Grams, Paul E.; Tusso, Robert B.; Buscombe, Daniel

2018-02-27

Automated camera systems deployed at 43 remote locations along the Colorado River corridor in Grand Canyon National Park, Arizona, are used to document sandbar erosion and deposition that are associated with the operations of Glen Canyon Dam. The camera systems, which can operate independently for a year or more, consist of a digital camera triggered by a separate data controller, both of which are powered by an external battery and solar panel. Analysis of images for categorical changes in sandbar size show deposition at 50 percent or more of monitoring sites during controlled flood releases done in 2012, 2013, 2014, and 2016. The images also depict erosion of sandbars and show that erosion rates were highest in the first 3 months following each controlled flood. Erosion rates were highest in 2015, the year of highest annual dam release volume. Comparison of the categorical estimates of sandbar change agree with sandbar change (erosion or deposition) measured by topographic surveys in 76 percent of cases evaluated. A semiautomated method for quantifying changes in sandbar area from the remote-camera images by rectifying the oblique images and segmenting the sandbar from the rest of the image is presented. Calculation of sandbar area by this method agrees with sandbar area determined by topographic survey within approximately 8 percent and allows quantification of sandbar area monthly (or more frequently).

Variation in Results Release and Patient Portal Access to Diagnostic Test Results at an Academic Medical Center

PubMed Central

Krasowski, Matthew D.; Grieme, Caleb V.; Cassady, Brian; Dreyer, Nicholas R.; Wanat, Karolyn A.; Hightower, Maia; Nepple, Kenneth G.

2017-01-01

Background: Electronic health records (EHRs) are commonplace in industrialized countries. Many hospitals are granting their patients access to their medical information through online patient portals. In this report, we describe a retrospective analysis of patient access to diagnostic test results released through the patient portal (MyChart; Epic, Inc.) at a state academic medical center. Methods: We analyzed 6 months of data for anatomic pathology, clinical laboratory, and radiology test results to evaluate variations in results release (automated vs. manual) and subsequent patient access to the institutional patient portal. During this period, diagnostic test results were released for all patient encounters including inpatient units, outpatient clinics, and the emergency department. Results: Manual results release by providers before automated release time occurred most commonly in the outpatient setting. The highest rates of access of diagnostic test results occurred for outpatients (about 30% overall view rate), females (two times or more compared to males in nearly every age bracket), and 20–45-year-old. Access rates of diagnostic tests in the emergency department or inpatient units were <10% across all populations. Access of diagnostic test results was very low for 12–17-year-old, likely influenced by institutional policies limiting parental proxy access within this pediatric age range. Approximately 20% of outpatient laboratory results were viewed by patients within 8 h of release from the EHR to the patient portal and 10% within 2 h of release. Conclusions: Patient accessing of diagnostic test results were generally higher for females, outpatients, and 20–45-year-old. Approximately, 20% of outpatient results were viewed quickly by patients after release to the EHR. PMID:29226008

Variation in Results Release and Patient Portal Access to Diagnostic Test Results at an Academic Medical Center.

PubMed

Krasowski, Matthew D; Grieme, Caleb V; Cassady, Brian; Dreyer, Nicholas R; Wanat, Karolyn A; Hightower, Maia; Nepple, Kenneth G

2017-01-01

Electronic health records (EHRs) are commonplace in industrialized countries. Many hospitals are granting their patients access to their medical information through online patient portals. In this report, we describe a retrospective analysis of patient access to diagnostic test results released through the patient portal (MyChart; Epic, Inc.) at a state academic medical center. We analyzed 6 months of data for anatomic pathology, clinical laboratory, and radiology test results to evaluate variations in results release (automated vs. manual) and subsequent patient access to the institutional patient portal. During this period, diagnostic test results were released for all patient encounters including inpatient units, outpatient clinics, and the emergency department. Manual results release by providers before automated release time occurred most commonly in the outpatient setting. The highest rates of access of diagnostic test results occurred for outpatients (about 30% overall view rate), females (two times or more compared to males in nearly every age bracket), and 20-45-year-old. Access rates of diagnostic tests in the emergency department or inpatient units were <10% across all populations. Access of diagnostic test results was very low for 12-17-year-old, likely influenced by institutional policies limiting parental proxy access within this pediatric age range. Approximately 20% of outpatient laboratory results were viewed by patients within 8 h of release from the EHR to the patient portal and 10% within 2 h of release. Patient accessing of diagnostic test results were generally higher for females, outpatients, and 20-45-year-old. Approximately, 20% of outpatient results were viewed quickly by patients after release to the EHR.

Illuminating pathways of forest nutrient provision: relative release from soil mineral and organic pools

NASA Astrophysics Data System (ADS)

Hauser, E.; Billings, S. A.

2017-12-01

Depletion of geogenic nutrients during soil weathering can prompt vegetation to rely on other sources, such as organic matter (OM) decay, to meet growth requirements. Weathered soils also tend to permit deep rooting, a phenomenon sometimes attributed to vegetation foraging for geogenic nutrients. This study examines the extent to which OM recycling provides nutrients to vegetation growing in soils with diverse weathering states. We thus address the fundamental problem of how forest vegetation obtains sufficient nutrition to support productivity despite wide variation in soils' nutrient contents. We hypothesized that vegetation growing on highly weathered soils relies on nutrients released from OM decay to a greater extent than vegetation growing on less weathered, more nutrient-rich substrates. For four mineralogically diverse Critical Zone Observatories (CZO) and Critical Zone Exploratory Network sites, we calculated weathering indices and approximated vegetation nutrient demand and nutrient release from OM decay. We also measured nutrient release rates from OM decay at each site. We then assessed the relationship between degree of soil weathering and the estimated fraction of nutrient demand satisfied by OM derived nutrients. Results are consistent with our hypothesis. The chemical index of alteration (CIA), a weathering index that increases in value with mineral depletion, varies predictably from 90 at the highly weathered Calhoun CZO to 60 at the Catalina CZO, where soils are more recently developed. Estimates of rates of K release from OM decay increase with CIA values. The highest release rate is 2.4 gK m-2 y-1 at Calhoun, accounting for 30% of annual vegetation K uptake; at Catalina, less than 0.5 gm-2 y-1 K is released, meeting 14% of vegetation demand. CIA also co-varies with rooting depth across sites: the deepest roots at the Calhoun sites are growing in soils with the highest CIA values, while the deepest roots at Catalina sites are growing in soils with much lower CIA values. Thus, provision of plant-available nutrients from OM decay appears greater at more weathered sites, and dominant nutrient sources accessed by deep roots (OM- vs. rock-derived) may vary predictably with soil weathering stage. On-going incubations will permit us to assess these relationships for multiple geogenic nutrients.

Assessment of commercially available pheromone lures for monitoring diamondback moth (Lepidoptera: Plutellidae) in canola.

PubMed

Evenden, M L; Gries, R

2010-06-01

Sex pheromone monitoring lures from five different commercial sources were compared for their attractiveness to male diamondback moth, Plutella xylostella L. (Lepidoptera: Plutellidae) in canola, Brassica napus L., fields in western Canada. Lures that had the highest pheromone release rate, as determined by aeration analyses in the laboratory, were the least attractive in field tests. Lures from all the commercial sources tested released more (Z)-11-hexadecenal than (Z)-11-hexadecenyl acetate and the most attractive lures released a significantly higher aldehyde to acetate ratio than less attractive lures. Traps baited with sex pheromone lures from APTIV Inc. (Portland, OR) and ConTech Enterprises Inc. (Delta, BC, Canada) consistently captured more male diamondback moths than traps baited with lures from the other sources tested. In two different lure longevity field trapping experiments, older lures were more attractive to male diamondback moths than fresh lures. Pheromone release from aged lures was constant at very low release rates. The most attractive commercially available sex pheromone lures tested attracted fewer diamondback moth males than calling virgin female moths suggesting that research on the development of a more attractive synthetic sex pheromone lure is warranted.

Alteration of belowground carbon dynamics by nitrogen addition in southern California mixed conifer forests

Treesearch

N.S. Nowinski; S.E. Trumbore; G. Jimenez; M.E. Fenn

2009-01-01

Nitrogen deposition rates in southern California are the highest in North America and have had substantial effects on ecosystem functioning. We document changes in the belowground C cycle near ponderosa pine trees experiencing experimental nitrogen (N) addition (50 and 150 kg N ha−1 a−1 as slow release urea since 1997) at two end‐member...

Risk of fentanyl-involved overdose among those with past year incarceration: Findings from a recent outbreak in 2014 and 2015.

PubMed

Brinkley-Rubinstein, Lauren; Macmadu, Alexandria; Marshall, Brandon D L; Heise, Andrew; Ranapurwala, Shabbar I; Rich, Josiah D; Green, Traci C

2018-04-01

Overdose is the leading cause of unintentional injury-related death. Rhode Island (RI) has the highest rate of illicit drug use nationally and the 5th highest overdose mortality rate. RI has experienced an outbreak of fentanyl-related overdoses. In incarcerated populations, risk of overdose is greatly elevated. However, little is known about fentanyl-related overdose post-release. In the current analyses, we identify changes in fentanyl-related fatal overdose among those who died in 2014 and 2015 who were incarcerated in the year before death. We linked data from the RI Office of the Medical Examiner with records from the RI Department of Corrections. We calculated risk ratios and 95% confidence intervals using log-binomial regression to compare risk of fentanyl-involved overdose death. We also compared median time to death since release, median sentence length, and median number of incarcerations in 2014 and 2015. Results indicate that the risk of dying of a fentanyl-related overdose increased (RR: 1.99 (95% CI: 1.11-3.57, p = 0.014)) from 2014 to 2015 among those with past year incarceration. This study is one of the first to describe fentanyl-related fatal overdose among those with past year incarceration. In 2015 the median sentence was longer among those with a fentanyl-related overdose death and the median time from release to death among all who had past year incarceration extended past 90 days. Access to medications for addiction treatment, overdose education, and naloxone should be available during community re-entry and extended beyond the early post-release period. Copyright © 2018. Published by Elsevier B.V.

Effect of ball milling on structures and properties of dispersed-type dental amalgam.

PubMed

Chern Lin, Jiin-Huey; Chen, Fred Ying-Yi; Chiang, Hui-Ju; Ju, Chien-Ping

2011-04-01

The purpose of the present study was to investigate the effect of ball milling on the initial mercury vapor release rate and mechanical properties such as compressive strength, diametral tensile strength and creep value, of the dispersed-type dental amalgam, and comparison was made with respect to two commercial amalgam alloys. Ball milling was employed to modify the configuration of the originally spherical-shaped Ag-Cu-Pd dispersant alloy particles. Improvement in mechanical properties while maintaining a low early-stage mercury vapor release rate of the amalgam is attempted. The experimental results show that the amalgam (AmB10) which was made from Ag-Cu-Pd dispersant alloy particles that were ball-milled for 10 min and heat-treated at 300 °C for 2 days exhibited a low initial mercury vapor release rate of 69 pg/mm(2)/s, which was comparable with that of commercial amalgam alloy Tytin (68 pg/mm(2)/s), and was lower than that of Dispersalloy (73 pg/mm(2)/s). As for mechanical properties, amalgam AmB10 exhibited the highest 1h compressive strength (228 MPa), which was higher than that of commercial amalgam alloy Dispersalloy by 72%; while its 24h diametral tensile strength was also the highest (177 MPa), and was higher than that of Dispersalloy by 55%. Furthermore, the creep value of the amalgams made from Ag-Cu-Pd alloy particles with 10 min ball-milling and heat treatment at 300 °C for 2 days was measured to be 0.12%, which was about 20% that of Dispersalloy. It is found that ball milling of the dispersant Ag-Cu-Pd alloy particles for 10 min was able to modify the configuration of the alloy particles into irregular-shapes. Subsequently, heat treatment at 300 °C significantly lowered the initial mercury vapor release rate, increased its 1h compressive strength and 1h diametral tensile strength, and lowered its creep value. Copyright © 2010 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Ball flight kinematics, release variability and in-season performance in elite baseball pitching.

PubMed

Whiteside, D; McGinnis, R S; Deneweth, J M; Zernicke, R F; Goulet, G C

2016-03-01

The purpose of this study was to quantify ball flight kinematics (ball speed, spin rate, spin axis orientation, seam orientation) and release location variability in the four most common pitch types in baseball and relate them to in-season pitching performance. Nine NCAA Division I pitchers threw four pitching variations (fastball, changeup, curveball, and slider) while a radar gun measured ball speed and a 600-Hz video camera recorded the ball trajectory. Marks on the ball were digitized to measure ball flight kinematics and release location. Ball speed was highest in the fastball, though spin rate was similar in the fastball and breaking pitches. Two distinct spin axis orientations were noted: one characterizing the fastball and changeup, and another, the curveball and slider. The horizontal release location was significantly more variable than the vertical release location. In-season pitching success was not correlated to any of the measured variables. These findings are instructive for inferring appropriate hand mechanics and spin types in each of the four pitches. Coaches should also be aware that ball flight kinematics might not directly relate to pitching success at the collegiate level. Therefore, talent identification and pitching evaluations should encompass other (e.g., cognitive, psychological, and physiological) factors. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Influence of eggs on the aroma composition of a sponge cake and on the aroma release in model studies on flavored sponge cakes.

PubMed

Pozo-Bayón, Maria Angeles; Ruíz-Rodríguez, Alejandro; Pernin, Karine; Cayot, Nathalie

2007-02-21

The use of solvent-assisted flavor evaporation extraction (SAFE) and purge and trap in Tenax allowed the identification of more than 100 volatile compounds in a sponge cake (SC-e). Gas chromatography-olfactometry (GC-O) of the SAFE extracts of crumb and crust were achieved in order to determine the most potent odorants of SC-e. The change in the traditional dough formulation of SC-e in which eggs were substituted by baking powder (SC-b) as the leavening agent produced important changes in some key aroma compounds. The release curves of some aroma compounds-some of them generated during baking and others added in the dough-were followed by cumulative headspace analysis. In the flavored SC-b, the aroma release curves showed a plateau after 15 min of purge, while the release increased proportionally with the purge time in the flavored SC-e. In general, except for some of the aroma compounds with the highest log P values, the rate of release of most of the added and generated aroma compounds was significantly influenced by the changes in the cake formulation. The higher rates of release found for the aroma compounds in SC-b could contribute to explain its rapid exhaustion of aroma compounds in the purge and trap experiments and might lead to poorer sensorial characteristics of this cake during storage.

Enhanced rectal absorption of amphotericin B lyophilized with glycyrrhizinate in rabbits.

PubMed

Tanaka, M; Kuwahara, E; Takahashi, M; Koyama, O; Takahashi, N; Yotsuyanagi, T

1998-08-01

The influence of bases and additives in the formulation for rectal absorption of amphotericin B (AMB) lyophilized with dipotassium glycyrrhizinate (GLYK) was investigated using rabbits in relation to an in vitro release test. The release of AMB from the fatty base of Witepsol or a medium chain triglyceride (MCT) was markedly faster than that from the hydrophilic base of macrogol. The addition of polyoxyethylene (2) lauryl ether (POE(2)LE) into the fatty bases led to a marked increase in the release rate, whereas POE(9)LE or sodium lauryl sulfate resulted in a significantly lower release rate. Animals received rectally each of seven AMB formulations of Witepsol H-15, macrogol, MCT with surfactants and aqueous solution. The absorption of the AMB lyophilized mixture with GLYK at a 1:9 molar ratio from a MCT base was significantly superior to that from macrogol. The addition of POE(2)LE into the MCT base resulted in a marked increase in bioavailability, showing the highest bioavailability of 4.9%. High serum levels of over 100 ng/ml of serum were maintained for 24 h following administration. The lowest bioavailability was 0.32% for the macrogol suppository. There was a good correlation between the release rate of AMB from the formulations and bioavailability. These results suggest that an AMB rectal formulation may provide a promising therapeutic alternative to infusion, taking into account the serum level of AMB exceeding the minimal inhibitory concentration of the infecting organism.

Effect of chronic d-fenfluramine administration on rat hypothalamic serotonin levels and release

NASA Technical Reports Server (NTRS)

Schaechter, Judith D.; Wurtman, Richard J.

1988-01-01

D-fenfluramine, an anorectic agent in rats and man, was administered daily at doses 1.25, 2.5, 5, or 10 mg/kg/day for 10 days, and sacrificed 6 days later. Hypothalamic serotonin (5-HT) levels were unchanged in rats receiving 1.25-5 mg/kg/day of d-fenfluramine but reduced by 22 percent (p less than 0.01) at the highest drug dose (10 mg/kg/day); hypothalamic 5-hydroxyindole acetic acid (5-HIAA) levels were reduced by 15 percent (p less than 0.05) or 28 percent (p less than 0.01) in rats receiving 5 or 10 mg/kg/day of the drug, respectively. Hypothalamic slices prepared from rats which were previously treated with any of the drug doses spontaneously released endogenous 5-HT at rates that did not differ from those of vehicle-treated rats. 5-HT released with electrical field-stimulation was unaffected by prior d-fenfluramine treatment at doses of 1.25-5 mg/kg/day, and was reduced by 20 percent (p less than 0.05) from slices prepared from rats which received 10 mg/kg/day. 5-HIAA efflux was also attenuated by the highest drug dose. These data indicate that chronic administration to rats of customary anorectic doses of d-fenfluramine (i.e. 0.06-1.25 mg/kg) fail to cause long-lasting reductions in brain 5-HT release.

Role of seagrass photosynthesis in root aerobic processes.

PubMed

Smith, R D; Dennison, W C; Alberte, R S

1984-04-01

The role of shoot photosynthesis as a means of supporting aerobic respiration in the roots of the seagrass Zostera marina was examined. O(2) was transported rapidly (10-15 minutes) from the shoots to the root-rhizome tissues upon shoot illumination. The highest rates of transport were in shoots possessing the greatest biomass and leaf area. The rates of O(2) transport do not support a simple gas phase diffusion mechanism. O(2) transport to the root-rhizome system supported aerobic root respiration and in many cases exceeded respiratory requirements leading to O(2) release from the subterranean tissue. Release of O(2) can support aerobic processes in reducing sediments typical of Z. marina habitats. Since the root-rhizome respiration is supported primarily under shoot photosynthetic conditions, then the daily period of photosynthesis determines the diurnal period of root aerobiosis.

Oleic Acid enhances all-trans retinoic Acid loading in nano-lipid emulsions.

PubMed

Chinsriwongkul, Akhayachatra; Opanasopit, Praneet; Ngawhirunpat, Tanasait; Rojanarata, Theerasak; Sila-On, Warisada; Ruktanonchai, Uracha

2010-01-01

The aim of this study was to investigate the enhancement of all-trans retinoic acid (ATRA) loading in nano-lipid emulsions and stability by using oleic acid. The effect of formulation factors including initial ATRA concentration and the type of oil on the physicochemical properties, that is, percentage yield, percentage drug release, and photostability of formulations, was determined. The solubility of ATRA was increased in the order of oleic acid > MCT > soybean oil > water. The physicochemical properties of ATRA-loaded lipid emulsion, including mean particle diameter and zeta potential, were modulated by changing an initial ATRA concentration as well as the type and mixing ratio of oil and oleic acid as an oil phase. The particles of lipid emulsions had average sizes of less than 250 nm and negative zeta potential. The addition of oleic acid in lipid emulsions resulted in high loading capacity. The photodegradation rate was found to be dependent on the initial drug concentration but independent of the type of oily phase used in this study. The release rates were not affected by initial ATRA concentration but were affected by the type of oil, where oleic acid showed the highest release rate of ATRA from lipid emulsions.

A long-term retrospective study on rehabilitation of seabirds in Gran Canaria Island, Spain (2003-2013).

PubMed

Montesdeoca, Natalia; Calabuig, Pascual; Corbera, Juan A; Orós, Jorge

2017-01-01

The aims of this study were to analyze the causes of morbidity and mortality in a large population of seabirds admitted to the Tafira Wildlife Rehabilitation Center (TWRC) in Gran Canaria Island, Spain, from 2003 to 2013, and to analyze the outcomes of the rehabilitation process. We included 1,956 seabirds (133 dead on admission and 1,823 admitted alive) in this study. Causes of morbidity were classified into nine categories: light pollution (fallout), fishing gear interaction, crude oil, poisoning/intoxication, other traumas, metabolic/nutritional disorder, orphaned young birds, other causes, and unknown/undetermined. The crude and stratified (by causes of admission) rates of the three final disposition categories (euthanasia Er, unassisted mortality Mr, and release Rr), the time until death, and the length of stay were also studied for the seabirds admitted alive. Yellow-legged Gull (Larus michahellis) was the species most frequently admitted (46.52%), followed by Cory's Shearwater (Calonectris diomedea borealis) (20.09%). The most frequent causes of morbidity were light pollution (fallout) (25.81%), poisoning/intoxication (24.69%), and other traumas (18.14%). The final disposition rates were: Er = 15.35%, Mr = 16.29%, and Rr = 68.34%. The highest Er was observed in the 'other traumas' category (58.08%). Seabirds admitted due to metabolic/nutritional disorder had the highest Mr (50%). The highest Rr was observed in the light pollution (fallout) category (99.20%). This survey provides useful information for the conservation of several seabird species. We suggest that at least the stratified analysis by causes of admission of the three final disposition rates, and the parameters time until death and length of stay at the center should be included in the outcome research of the rehabilitation of seabirds. The high release rate for seabirds (68.34%) achieved at the TWRC emphasizes the importance of wildlife rehabilitation centers for the conservation of seabirds.

A long-term retrospective study on rehabilitation of seabirds in Gran Canaria Island, Spain (2003-2013)

PubMed Central

Montesdeoca, Natalia; Calabuig, Pascual; Corbera, Juan A.

2017-01-01

Aims The aims of this study were to analyze the causes of morbidity and mortality in a large population of seabirds admitted to the Tafira Wildlife Rehabilitation Center (TWRC) in Gran Canaria Island, Spain, from 2003 to 2013, and to analyze the outcomes of the rehabilitation process. Methods We included 1,956 seabirds (133 dead on admission and 1,823 admitted alive) in this study. Causes of morbidity were classified into nine categories: light pollution (fallout), fishing gear interaction, crude oil, poisoning/intoxication, other traumas, metabolic/nutritional disorder, orphaned young birds, other causes, and unknown/undetermined. The crude and stratified (by causes of admission) rates of the three final disposition categories (euthanasia Er, unassisted mortality Mr, and release Rr), the time until death, and the length of stay were also studied for the seabirds admitted alive. Results Yellow-legged Gull (Larus michahellis) was the species most frequently admitted (46.52%), followed by Cory’s Shearwater (Calonectris diomedea borealis) (20.09%). The most frequent causes of morbidity were light pollution (fallout) (25.81%), poisoning/intoxication (24.69%), and other traumas (18.14%). The final disposition rates were: Er = 15.35%, Mr = 16.29%, and Rr = 68.34%. The highest Er was observed in the ‘other traumas’ category (58.08%). Seabirds admitted due to metabolic/nutritional disorder had the highest Mr (50%). The highest Rr was observed in the light pollution (fallout) category (99.20%). Conclusions This survey provides useful information for the conservation of several seabird species. We suggest that at least the stratified analysis by causes of admission of the three final disposition rates, and the parameters time until death and length of stay at the center should be included in the outcome research of the rehabilitation of seabirds. The high release rate for seabirds (68.34%) achieved at the TWRC emphasizes the importance of wildlife rehabilitation centers for the conservation of seabirds. PMID:28475653

Natural ageing process accelerates the release of Ag from functional textile in various exposure scenarios

PubMed Central

Ding, Dahu; Chen, Lulu; Dong, Shaowei; Cai, Hao; Chen, Jifei; Jiang, Canlan; Cai, Tianming

2016-01-01

Natural ageing process occurs throughout the life cycle of textile products, which may possess influences on the release behavior of additives such as silver nanoparticles (Ag NPs). In this study, we assessed the releasability of Ag NPs from a Ag NPs functionalized textile in five different exposure scenarios (i.e. tap water (TW), pond water (PW), rain water (RW), artificial sweat (AS), and detergent solution (DS) along with deionized water (DW) as reference), which were very likely to occur throughout the life cycle of the textile. For the pristine textile, although the most remarkable release was found in DW (6–15 μg Ag/g textile), the highest release rate was found in RW (around 7 μg Ag/(g textile·h)). After ageing treatment, the total released Ag could be increased by 75.7~386.0% in DW, AS and DS. Morphological analysis clearly showed that the Ag NPs were isolated from the surface of the textile fibre due to the ageing treatment. This study provides useful information for risk assessment of nano-enhanced textile products. PMID:27869136

Natural ageing process accelerates the release of Ag from functional textile in various exposure scenarios

NASA Astrophysics Data System (ADS)

Ding, Dahu; Chen, Lulu; Dong, Shaowei; Cai, Hao; Chen, Jifei; Jiang, Canlan; Cai, Tianming

2016-11-01

Natural ageing process occurs throughout the life cycle of textile products, which may possess influences on the release behavior of additives such as silver nanoparticles (Ag NPs). In this study, we assessed the releasability of Ag NPs from a Ag NPs functionalized textile in five different exposure scenarios (i.e. tap water (TW), pond water (PW), rain water (RW), artificial sweat (AS), and detergent solution (DS) along with deionized water (DW) as reference), which were very likely to occur throughout the life cycle of the textile. For the pristine textile, although the most remarkable release was found in DW (6-15 μg Ag/g textile), the highest release rate was found in RW (around 7 μg Ag/(g textile·h)). After ageing treatment, the total released Ag could be increased by 75.7~386.0% in DW, AS and DS. Morphological analysis clearly showed that the Ag NPs were isolated from the surface of the textile fibre due to the ageing treatment. This study provides useful information for risk assessment of nano-enhanced textile products.

Effects of water temperature and substrate type on spore production and release in eastern Tubifex tubifex worms infected with Myxobolus cerebralis

USGS Publications Warehouse

Blazer, V.S.; Waldrop, T.B.; Schill, W.B.; Densmore, Christine L.; Smith, D.

2003-01-01

Eastern Tubifex tubifex worms were exposed to Myxobolus cerebralis spores at 9, 13, 17, and 20 C in 1-L jars that contained sand, mud, or leaf litter as substrata. Beginning 60 days after exposure, water from each jar was filtered daily and examined for the presence of waterborne triactinomyxon spores (TAMs). On discovering a single TAM from an experimental jar, 48 T. tubifex worms from that jar were placed individually into 24-well plates. Spores released from individual infected T. tubifex worms were quantified to determine the first day of TAM release from infected worms, the infection rate, the total number of TAMs released per worm, and the duration of release. No TAMs were found in any of the jars incubated at 20 C or in uninfected, control worms at any temperature. The total number of TAMs released by infected worms in mud and sand was highest at 13 C compared with other temperatures. Infection rates among individual worms increased with temperature between 9 and 17 C. Higher temperatures (up to 17 C) induced earlier TAM releases among infected worms, and substratum did not influence this production parameter. The average duration of TAM release decreased as the temperature increased from 9 to 17 C, and there was a significant effect of substratum in the groups maintained at 13 and 17 C. In all temperature treatments between 9 and 17 C, the duration of release was least in the worms maintained in leaf litter, as was the total number of TAMs released during the experimental period and the median number of TAMs per production day.

Seasonal arsenic accumulation in stream sediments at a groundwater discharge zone.

PubMed

MacKay, Allison A; Gan, Ping; Yu, Ran; Smets, Barth F

2014-01-21

Seasonal changes in arsenic and iron accumulation rates were examined in the sediments of a brook that receives groundwater discharges of arsenic and reduced iron. Clean glass bead columns were deployed in sediments for known periods over the annual hydrologic cycle to monitor changes in arsenic and iron concentrations in bead coatings. The highest accumulation rates occurred during the dry summer period (July-October) when groundwater discharges were likely greatest at the sample locations. The intermediate flow period (October-March), with higher surface water levels, was associated with losses of arsenic and iron from bead column coatings at depths below 2-6 cm. Batch incubations indicated iron releases from solids to be induced by biological reduction of iron (oxy)hydroxide solids. Congruent arsenic releases during incubation were limited by the high arsenic sorption capacity (0.536 mg(As)/mg(Fe)) of unreacted iron oxide solids. The flooded spring (March-June) with high surface water flows showed the lowest arsenic and iron accumulation rates in the sediments. Comparisons of accumulation rates across a shoreline transect were consistent with greater rates at regions exposed above surface water levels for longer times and greater losses at locations submerged below surface water. Iron (oxy)hydroxide solids in the shallowest sediments likely serve as a passive barrier to sorb arsenic released to pore water at depth by biological iron reduction.

Social Environment and Hospitalisation after Release from Prison: A Prospective Cohort Study

PubMed Central

2017-01-01

This study examined the association between remoteness and area disadvantage, and the rate of subsequent hospitalisation, in a cohort of adults released from prisons in Queensland. A baseline survey of 1267 adult prisoners within 6 weeks of expected release was prospectively linked with hospital, mortality and reincarceration records. Postcodes were used to assign remoteness and area disadvantage categories. Multivariate Andersen–Gill regression models were fitted to test for associations between remoteness, area disadvantage and hospitalisation after release from prison. Over a total of 3090.9 person-years of follow-up, the highest crude incidence rates were observed in areas characterised by remoteness and area disadvantage (crude incidence rate (IR) = 649; 95%CI: 526–791), followed by remoteness only (IR = 420; 95%CI: 349–501), severe area disadvantage only (IR = 403; 95%CI: 351–461), and neither of these factors (IR = 361; 95%CI: 336–388). Unadjusted analyses indicated that remoteness (hazard ratio (HR) = 1.32; 95%CI: 1.04–1.69; p = 0.024) was associated with increased risk of hospitalisation; however, this attenuated to the null after adjustment for covariate factors. The incidence of hospitalisation for those who live in remote or socio-economically disadvantaged areas is increased compared to their counterparts in more urban and less socio-economically disadvantaged areas. Experiencing both these factors together may compound the hospitalisation in the community. PMID:29149091

Seasonal dynamics of nitrate and ammonium ion concentrations in soil solutions collected using MacroRhizon suction cups.

PubMed

Kabala, Cezary; Karczewska, Anna; Gałka, Bernard; Cuske, Mateusz; Sowiński, Józef

2017-07-01

The aims of the study were to analyse the concentration of nitrate and ammonium ions in soil solutions obtained using MacroRhizon miniaturized composite suction cups under field conditions and to determine potential nitrogen leaching from soil fertilized with three types of fertilizers (standard urea, slow-release urea, and ammonium nitrate) at the doses of 90 and 180 kg ha -1 , applied once or divided into two rates. During a 3-year growing experiment with sugar sorghum, the concentration of nitrate and ammonium ions in soil solutions was the highest with standard urea fertilization and the lowest in variants fertilized with slow-release urea for most of the months of the growing season. Higher concentrations of both nitrogen forms were noted at the fertilizer dose of 180 kg ha -1 . One-time fertilization, at both doses, resulted in higher nitrate concentrations in June and July, while dividing the dose into two rates resulted in higher nitrate concentrations between August and November. The highest potential for nitrate leaching during the growing season was in July. The tests confirmed that the miniaturized suction cups MacroRhizon are highly useful for routine monitoring the concentration of nitrate and ammonium ions in soil solutions under field conditions.

An investigation into the characteristics and drug release properties of multiple W/O/W emulsion systems containing low concentration of lipophilic polymeric emulsifier.

PubMed

Vasiljevic, Dragana; Parojcic, Jelena; Primorac, Marija; Vuleta, Gordana

2006-02-17

Multiple W/O/W emulsions with high content of inner phase (Phi1=Phi2=0.8) were prepared using relatively low concentrations of lipophilic polymeric primary emulsifier, PEG 30-dipolyhydroxystearate, and diclofenac diethylamine (DDA) as a model drug. The investigated formulations were characterized and their stability over the time was evaluated by dynamic and oscillatory rheological measurements, microscopic analysis and in vitro drug release study. In vitro release profiles of the selected model drug were evaluated in terms of the effective diffusion coefficients and flux of the released drug. The multiple emulsion samples exhibited good stability during the ageing time. Concentration of the lipophilic primary emulsifier markedly affected rheological behaviour as well as the droplet size and in vitro drug release kinetics of the investigated systems. The multiple emulsion systems with highest concentration (2.4%, w/w) of the primary emulsifier had the lowest droplet size and the highest apparent viscosity and highest elastic characteristics. Drug release data indicated predominately diffusional drug release mechanism with sustained and prolonged drug release accomplished with 2.4% (w/w) of lipophilic emulsifier employed.

Atmospheric modeling of Mars CH4 subsurface clathrates releases mimicking SAM and 2003 Earth-based detections

NASA Astrophysics Data System (ADS)

Pla-García, J.; Rafkin, S. C.

2017-12-01

The aim of this work is to establish the amount of mixing during all martian seasons to test whether CH4 releases inside or outside of Gale crater are consistent with MSL-SAM observations. Several modeling scenarios were configured, including instantaneous and steady releases, both inside and outside the crater. A simulation to mimic the 2003 Earth-based detections (Mumma et al. 2009 or M09) was also performed. In the instantaneous release inside Gale experiments, Ls270 was shown to be the faster mixing season when air within and outside the crater was well mixed: all tracer mass inside the crater is diluted after just 8 hours. The mixing of near surface crater air with the external environment in the rest of the year is potentially rapid but slower than Ls270.In the instantaneous release outside Gale (NW) experiment, in just 12 hours the CH4 that makes it to the MSL landing location is diluted by six orders of magnitude. The timescale of mixing in MRAMS experiments is on the order of 1 sol regardless of season. The duration of the CH4 peak observed by SAM is 100 sols. Therefore there is a steady release inside the crater, or there is a very large magnitude steady release outside the crater. In the steady release Gale experiments, CH4 flux rate from ground is 1.8 kg m-2 s-1 (derived from Gloesener et al. 2017 clathrates fluxes) and it is not predictive. In these experiments, 200 times lower CH4 values detected by SAM are modeled around MSL location. There are CH4 concentration variations of orders of magnitude depending on the hour, so timing of SAM measurements is important. With a larger (but further away) outside crater release area compared to inside, similar CH4 values around MSL are modeled, so distance to source is important. In the steady experiments mimicking M09 detection release area, only 12 times lower CH4 values detected by SAM are modeled around MSL. The highest value in the M09 modeled scenario (0.6 ppbv) is reached in Ls270. This value is the highest of all modeled experiments. With our initial conditions (flux rates, release area size and distance to MSL), SAM should not be able (or very difficult) to detect CH4, but if we multiply flux by 12, increase the release area or move it closer to MSL (or all of above), it may be possible to get CH4 values that SAM could detect regardless where it comes from: inside, outside (close to) or far away from Gale.

[Fluoride release and recharge properties of six restorative materials].

PubMed

Gui, Yajie; Zhao, Xinyi; Li, Shibao; Tang, Lihui; Gong, Xu

2015-01-01

To evaluate the F(-) releasing and recharging properties of six dental restorative materials. Disc specimens 10 mm in diameter and 1 mm in thickness were prepared from 6 different dental restorative materials: Fuji VII [glass ionomer cement (GIC)], Fuji II LC (light-curing, GIC), Beautifil (giomer), Compoglass F (compomer), Charisma (composite) and Experimental I (a fluoride releasing composite), with 10 discs for each material. Specimens were dipped in 5 ml deionized water and F(-) release was detected using a fluoride-specific ion electrode every day from 1-7 days and every three days from 8-28 days. On day 28, specimens were exposed to a fluoride foam for 4 min and then dipped in water, then the F(-) concentration was detected every day for a week. The specimens were exposed to fluoride foam and fluoride release was detected repeatedly for three times. All materials presented the highest F(-) release on the first day after dipping and the F(-) release sharply decreased after 24 h and slowly decreased after 3 days. On the first day, Fuji VII presented the highest F(-) release[(99.68±15.21) µg×cm(-2)×d(-1)], followed by Fuji II LC [(37.12±1.67) µg×cm(-2)×d(-1)], Experimental I [(22.93±1.53) µg×cm(-2)×d(-1)], Compoglass F[(15.28±0.70) µg×cm(-2)×d(-1)], Beautifil[(2.40±0.52) µg×cm(-2)×d(-1)] and Charisma[(0.11±0.02) µg×cm(-2)×d(-1)]. Within 28 days of dipping, both Fuji VII and Fuji II LC released more F(-) than other materials did(P < 0.05), followed by Compoglass F and Experimental I, and Beautifil and Charisma released the least F(-)(P < 0.01). After F(-) uptake, all materials released the highest F- on the first day and presented sharply decrease after 24 h and slowly decrease after 2 days. On the first day after F(-) uptake, Fuji VII presented the highest F(-) release (>40 µg×cm(-2) ×d(-1)), much more than other materials(P < 0.01), followed by Fuji II LC(>25 µg×cm(-2) ×d(-1)). Beautifil, Compoglass F and Experimental I were close in F(-) release value(15- 20 µg × cm(-2) × d(-1)), and Charisma showed the lowest F(-) release. Two glass ionomers were shown to have highest capacity in F(-) release and uptake, followed by compomer and fluoride releasing composite. Composite demonstrated the lowest F(-) release and uptake and Giomer was comparable to composite in F(-) release and to compomer and fluoride releasing composite in F(-) uptake.

Development of a sustained fluoride delivery system.

PubMed

Baturina, Olga; Tufekci, Eser; Guney-Altay, Ozge; Khan, Shadeed M; Wnek, Gary E; Lindauer, Steven J

2010-11-01

To develop a novel delivery system by which fluoride incorporated into elastomeric rings, such as those used to ligate orthodontic wires, will be released in a controlled and constant manner. Polyethylene co-vinyl acetate (PEVA) was used as the model elastomer. Samples (N = 3) were prepared by incorporating 0.02 to 0.4 g of sodium fluoride (NaF) into previously prepared PEVA solution. Another group of samples prepared in the same manner were additionally dip-coated in PEVA to create an overcoat. Fluoride release studies were conducted in vitro using an ion selective electrode over a period of 45 days. The amount of fluoride released was compared to the optimal therapeutic dose of 0.7 microg F(-)/ring/d. Only coated samples with the highest fluoride content (group D, 0.4 g of NaF) were able to release fluoride at therapeutic levels. When fluoride release from coated and uncoated samples with the same amount of NaF were compared, it was shown that the dip-coating technique resulted in a fluoride release in a controlled manner while eliminating the initial burst effect. This novel fluoride delivery matrix provided fluoride release at a therapeutically effective rate and profile.

The Effect of Single, Binary and Ternary Anions of Chloride, Carbonate and Phosphate on the Release of 2,4-Dichlorophenoxyacetate Intercalated into the Zn-Al-layered Double Hydroxide Nanohybrid

NASA Astrophysics Data System (ADS)

Hussein, Mohd Zobir; Jaafar, Adila Mohamad; Yahaya, Asmah Hj.; Zainal, Zulkarnain

2009-11-01

Intercalation of beneficial anion into inorganic host has lead to an opportunity to synthesize various combinations of new organic-inorganic nanohybrids with various potential applications; especially, for the controlled release formulation and storage purposes. Investigation on the release behavior of 2,4-dichlorophenoxyacetate (2,4-D) intercalated into the interlayer of Zn-Al-layered double hydroxide (ZAN) have been carried out using single, binary and ternary aqueous systems of chloride, carbonate and phosphate. The release behavior of the active agent 2,4-D from its double-layered hydroxide nanohybrid ZANDI was found to be of controlled manner governed by pseudo-second order kinetics. It was found that carbonate medium yielded the highest accumulated release of 2,4-D, while phosphate in combination with carbonate and/or nitrate speeds up the release rate of 2,4-D. These results indicate that it is possible to design and develop new delivery system of latex stimulant compound with controlled release property based on 2,4-D that is known as a substance to increase latex production of rubber tree, Hevea brasiliensis.

Characterization of elemental release during microbe granite interactions at T = 28 °C

NASA Astrophysics Data System (ADS)

Wu, Lingling; Jacobson, Andrew D.; Hausner, Martina

2008-02-01

This study used batch reactors to characterize the mechanisms and rates of elemental release (Al, Ca, K, Mg, Na, F, Fe, P, Sr, and Si) during interaction of a single bacterial species ( Burkholderia fungorum) with granite at T = 28 °C for 35 days. The objective was to evaluate how actively metabolizing heterotrophic bacteria might influence granite weathering on the continents. We supplied glucose as a C source, either NH 4 or NO 3 as N sources, and either dissolved PO 4 or trace apatite in granite as P sources. Cell growth occurred under all experimental conditions. However, solution pH decreased from ˜7 to 4 in NH 4-bearing reactors, whereas pH remained near-neutral in NO 3-bearing reactors. Measurements of dissolved CO 2 and gluconate together with mass-balances for cell growth suggest that pH lowering in NH 4-bearing reactors resulted from gluconic acid release and H + extrusion during NH 4 uptake. In NO 3-bearing reactors, B. fungormum likely produced gluconic acid and consumed H + simultaneously during NO 3 utilization. Over the entire 35-day period, NH 4-bearing biotic reactors yielded the highest release rates for all elements considered. However, chemical analyses of biomass show that bacteria scavenged Na, P, and Sr during growth. Abiotic control reactors followed different reaction paths and experienced much lower elemental release rates compared to biotic reactors. Because release rates inversely correlate with pH, we conclude that proton-promoted dissolution was the dominant reaction mechanism. Solute speciation modeling indicates that formation of Al-F and Fe-F complexes in biotic reactors may have enhanced mineral solubilities and release rates by lowering Al and Fe activities. Mass-balances further reveal that Ca-bearing trace phases (calcite, fluorite, and fluorapatite) provided most of the dissolved Ca, whereas more abundant phases (plagioclase) contributed negligible amounts. Our findings imply that during the incipient stages of granite weathering, heterotrophic bacteria utilizing glucose and NH 4 only moderately elevate silicate weathering reactions that consume atmospheric CO 2. However, by enhancing the dissolution of non-silicate, Ca-bearing trace minerals, they could contribute to high Ca/Na ratios commonly observed in granitic watersheds.

Predator response to releases of American shad larvae in the Susquehanna River basin

USGS Publications Warehouse

Johnson, James H.; Ringler, N.H.

1998-01-01

Predation on American shad (Alosa sapidissima) larvae within the first two hours of release was examined from 1989 to 1992 on 31 occasions at stocking sites in the Susquehanna River basin. Twenty-two fish species consumed shad larvae; the dominant predators were spotfin shiner (Cyprinella spiloptera), mimic shiner (Notropis volucellus) and juvenile smallmouth bass (Micropterus dolomieu). The number of shad larvae found in predator stomachs ranged from 0 to 900. Mortality of shad larvae at the stocking site was usually less than 2%. The greatest mortality (9.6%) occurred at the highest stocking level (1.5 million larvae). Highly variable predation rates and release levels of shad insufficient to achieve predator satiation hindered the ability to determine a specific type of functional response of predators. Predator numbers increased with stocking density, indicating short-term aggregation at the release site. Because of practical problems associated with releasing the large numbers of larvae that would be required to satiate predators, routine stocking at these levels is probably unreasonable. Releases of 400,000 to 700,000 larvae may reduce predation by offsetting depensatory mechanisms that operate on small releases and the effects of increased predation due to predator aggregation on large releases. Night stocking may reduce predation on larval shad at the release site.

Release and diffusional modeling of metronidazole lipid matrices.

PubMed

Ozyazici, Mine; Gökçe, Evren H; Ertan, Gökhan

2006-07-01

In this study, the first aim was to investigate the swelling and relaxation properties of lipid matrix on diffusional exponent (n). The second aim was to determine the desired release profile of metronidazole lipid matrix tablets. We prepared metronidazole lipid matrix granules using Carnauba wax, Beeswax, Stearic acid, Cutina HR, Precirol ATO 5, and Compritol ATO 888 by hot fusion method and pressed the tablets of these granules. In vitro release test was performed using a standard USP dissolution apparatus I (basket method) with a stirring rate of 100 rpm at 37 degrees C in 900 ml of 0.1 N hydrochloric acid, adjusted to pH 1.2, as medium for the formulations' screening. Hardness, diameter-height ratio, friability, and swelling ratio were determined. Target release profile of metronidazole was also drawn. Stearic acid showed the highest and Carnauba wax showed the lowest release rates in all formulations used. Swelling ratios were calculated after the dissolution of tablets as 9.24%, 6.03%, 1.74%, and 1.07% for Cutina HR, Beeswax, Precirol ATO 5, and Compritol ATO 888, respectively. There was erosion in Stearic acid, but neither erosion nor swelling in Carnauba wax, was detected. According to the power law analysis, the diffusion mechanism was expressed as pure Fickian for Stearic acid and Carnauba wax and the coupling of Fickian and relaxation contributions for other Cutina HR, Beeswax, Compritol ATO 888, and Precirol ATO 5 tablets. It was found that Beeswax (kd=2.13) has a very close drug release rate with the target profile (kt=1.95). Our results suggested that swelling and relaxation properties of lipid matrices should be examined together for a correct evaluation on drug diffusion mechanism of insoluble matrices.

Methane and Carbon Dioxide Production Rates in Lake Sediments from Sub-Arctic Sweden

NASA Astrophysics Data System (ADS)

DeStasio, J.; Halloran, M.; Erickson, L. M.; Varner, R. K.; Johnson, J. E.; Setera, J.; Prado, M. F.; Wik, M.; Crill, P. M.

2013-12-01

Ecosystems at high latitudes are undergoing rapid change due to amplified arctic warming. Lakes in these regions are sources of both methane (CH4) and carbon dioxide (CO2) to the atmosphere and will likely be impacted by elevated temperatures. Because of the potential increase in the release of organic carbon due to thawing permafrost, it is believed that methanogenesis rates within neighboring fresh water sediments will display a positive feedback response, by increasing CH4 emission to the atmosphere. We studied CH4 production potential of sediments using cores from three lakes in the Stordalen Mire complex in sub-Arctic, Sweden: Inre Harrsjön, Mellan Harrsjön, and Villasjön. Sediment cores were incubated to determine CO2 and CH4 production rates and were analyzed for CH4 concentrations, dissolved inorganic carbon (DIC) concentrations, total organic carbon (TOC) concentrations, as well as carbon, nitrogen and sulfur content. Our results from the Villasjön cores indicate that CH4 production rates were highest at the same sediment depths as peak dissolved CH4 concentrations, with maximum values between depths of approximately 10cm and 30cm. Additionally, the highest observed CH4 production rates were in sediments from areas within Villasjön known to have the highest rates of CH4 ebullition. CO2 production rates were generally highest within surface sediments ranging from about 4cm to 11cm in depth, with production rates displaying a steady decrease below 11cm. Additionally, observed CO2 production rates correlated with total organic carbon (TOC) concentrations with respect to sediment depth, but displayed no relationship with dissolved inorganic carbon (DIC). Further analysis will be conducted to determine how CH4 and CO2 production characteristics vary between sediment core samples, as well as isotopic analysis of select samples taken from each lake.

Preparation of fast response superabsorbent hydrogels by radiation polymerization and crosslinking of N-isopropylacrylamide in solution

NASA Astrophysics Data System (ADS)

Abd El-Mohdy, H. L.; Safrany, Agnes

2008-03-01

Macroporous temperature-responsive poly( N-isopropylacrylamide) (PNIPAAm) hydrogels with high equilibrium swelling and fast response rates were obtained by a 60Co γ- and electron beam (EB) irradiation of aqueous N-isopropylacrylamide (NIPAAm) monomer solutions. The effect of irradiation temperatures, the dose, the addition of a pore-forming agent on the swelling ratio, and the kinetics of swelling and shrinking of the PNIPAAm gels was studied. The gels synthesized above the LCST exhibited the highest equilibrium swelling (300-400) and fastest response rate measured by minutes. Scanning electron microscope (SEM) pictures revealed that the gels synthesized above the LCST have larger pores than those prepared at temperatures below the LCST. The gels showed a reversible response to cyclical changes in temperature and might be used in a pulsed drug delivery device. The gels synthesized above the LCST exhibited the highest testosterone propionate release.

Elastic interactions between single microcrack and single osteon microstructure of human femur cortical bone

NASA Astrophysics Data System (ADS)

Mansor, N. N.; Daud, R.; Basaruddin, K. S.; Mat, F.; Bajuri, Y.; Ariffin, A. K.

2017-09-01

Inmultiscale Haversian system of cortical bone fracture, a homogenous bone modeling consideration is limited to only one Young modulus was significant for each cortex without having any constituents in that bone. A two dimension model of human femur cortical bone is presented by considering the anatomical positions of four cortices, e.g anterior, posterior, medial and lateral. The Haversian system is modeled under tensile loading by considering the interstitial matrix, osteon and cement line mechanical properties. The interaction between single microcrack and single osteon is evaluated using linear elastic fracture mechanics theory, and was determined using of stress intensity factor, strain energy release rate, and the critical stress intensity factor and critical strain energy release rate parameter. The results indicate that the medial cortex has the highest SIFs while the lowest was posterior cortex. The Young modulus of material was greatly influence the fracture parameters. More stiff the material, the SIF was reduced.

Selection of a computer code for Hanford low-level waste engineered-system performance assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

McGrail, B.P.; Mahoney, L.A.

Planned performance assessments for the proposed disposal of low-level waste (LLW) glass produced from remediation of wastes stored in underground tanks at Hanford, Washington will require calculations of radionuclide release rates from the subsurface disposal facility. These calculations will be done with the aid of computer codes. Currently available computer codes were ranked in terms of the feature sets implemented in the code that match a set of physical, chemical, numerical, and functional capabilities needed to assess release rates from the engineered system. The needed capabilities were identified from an analysis of the important physical and chemical process expected tomore » affect LLW glass corrosion and the mobility of radionuclides. The highest ranked computer code was found to be the ARES-CT code developed at PNL for the US Department of Energy for evaluation of and land disposal sites.« less

Volatile trace compounds released from municipal solid waste at the transfer stage: Evaluation of environmental impacts and odour pollution.

PubMed

Zhao, Yan; Lu, Wenjing; Wang, Hongtao

2015-12-30

Odour pollution caused by municipal solid waste is a public concern. This study quantitatively evaluated the concentration, environmental impacts, and olfaction of volatile trace compounds released from a waste transfer station. Seventy-six compounds were detected, and ethanol presented the highest releasing rate and ratio of 14.76 kg/d and 12.30 g/t of waste, respectively. Life cycle assessment showed that trichlorofluoromethane and dichlorodifluoromethane accounted for more than 99% of impact potentials to global warming and approximately 70% to human toxicity (non-carcinogenic). The major contributor for both photochemical ozone formation and ecotoxicity was ethanol. A detection threshold method was also used to evaluate odour pollution. Five compounds including methane thiol, hydrogen sulphide, ethanol, dimethyl disulphide, and dimethyl sulphide, with dilution multiples above one, were considered the critical compounds. Methane thiol showed the highest contribution to odour pollution of more than 90%, as indicated by its low threshold. Comparison of the contributions of the compounds to different environmental aspects indicated that typical pollutants varied based on specific evaluation targets and therefore should be comprehensively considered. This study provides important information and scientific methodology to elucidate the impacts of odourant compounds to the environment and odour pollution. Copyright © 2015 Elsevier B.V. All rights reserved.

Impact of functional properties and release kinetics on antioxidant activity of biopolymer active films and coatings.

PubMed

Benbettaïeb, Nasreddine; Tanner, Cadhla; Cayot, Philippe; Karbowiak, Thomas; Debeaufort, Frédéric

2018-03-01

This work deals with the study of the release kinetics of some natural antioxidants (ferulic acid, caffeic acid and tyrosol) from chitosan-fish gelatin edible films immersed ethanol at 96%, as well as the kinetics of their antioxidant activity using the DPPH assay. The aim was to determine how film functional properties influence the release kinetic and antioxidant activity. The addition of antioxidants to chitosan-fish gelatin matrix decreased the water vapour permeability by more than 30%. The tensile strength (TS) increased up to 50% after the incorporation of antioxidants. Some molecular interactions between polymer chains and antioxidants were confirmed by FTIR where spectra displayed a shift of the amide-III peak. Films containing caffeic acid or a caffeic-ferulic acid mixture exhibited the highest radical scavenging activity, leading to a 90% antioxidant activity at equilibrium but the release rate controlled the efficacy of the system. Copyright © 2017 Elsevier Ltd. All rights reserved.

Energy spectrum and kinetics of the fusing particles

NASA Astrophysics Data System (ADS)

Ryutov, D. D.; Putvinski, s. V.; Yushmanov, P. N.; TAE Team

2017-10-01

The fusing particles (e.g., D and T, or p and 11B) contribution to the reaction rate can be found by the integration of the fusion reactivity over the particle distribution functions. The distribution function (e.g., Maxwellian) is depleted in the energy range determined by the highest reactivity and has to be replenished by particle collisions. The kinetics of the replenishment process may affect the rate of fusion energy release. We present a simple analysis of the corresponding kinetic problems for the conditions typical for the standard and advanced-fuel fusion reactions and assess the possible effect on the reaction yield.

Biphasic insulin-releasing effect of BTS 67 582 in rats.

PubMed

Storey, D A; Bailey, C J

1998-12-01

BTS 67 582 (1,1-dimethyl-2(2-morpholinophenyl)guanidine fumarate) is being developed as a short-acting anti-diabetic insulin secretagogue. The effect of BTS 67 582 on the phasic pattern of insulin release was assessed in anaesthetized normal rats by measuring arterial plasma insulin concentrations while arterial glucose concentrations were fixed at 6, 8.5 and 12.5 mM. Intravenous BTS 67 582 (10 mg kg(-1)) induced an immediate but transient increase in insulin concentrations which declined by 10 min (first phase). This was followed by a smaller but sustained increase in insulin concentrations (second phase). The increment from basal to peak insulin release (0-2 min) was independent of glucose, but the first phase was maintained for longer and the second phase was greater at the highest concentration of glucose (12.5 mM). BTS 67 582 also extended the first-phase insulin response to a standard intravenous glucose challenge and enhanced the rate of glucose disappearance by approximately 12%. Thus BTS 67 582 causes biphasic stimulation of insulin release and augments the insulin-releasing effect of glucose.

Survival of hatchery Gulf sturgeon (Acipenser oxyrinchus desotoi Mitchill, 1815) in the Suwannee River, Florida: a 19-year evaluation

USGS Publications Warehouse

Sulak, Kenneth J.; Randall, Michael T.; Clugston, James P.

2014-01-01

An experimental release of 1192 hatchery-reared, individually PIT tagged, 220 days old (296–337 mm TL) Gulf sturgeon, Acipenser oxyrinchus desotoi, was undertaken in 1992 in the Suwannee River, Florida. The original objectives of the 1992 release experiment were to: (1) evaluate survival rate of cultured Gulf sturgeon in the wild vs survival rate of their wild 1992 cohort counterparts, (2) determine the differential effect of release site within the river upon long-term survival, and (3) evaluate comparative growth rates of recaptured hatchery vs captured wild 1992 cohort Gulf sturgeon. The present investigation addressed those original objectives, plus an additional fourth objective: (4) evaluation of hatchery fish recapture rate change over the 19-year experiment. The primary objective was to determine efficacy of potential conservation aquaculture for this species in terms of long-term survival in the wild. Follow-up 1993–2011 gill net sampling in freshwater reaches (rkm 4–237) and the estuarine river mouth (rkm −6 to 4) yielded recaptures representing 13.0% of the total released. Mean annual hatchery fish mortality (including emigration) rate estimated for the 19-year period (1993–2011) was more than twice that for same cohort wild fish. Mark-recapture survival probability (phi) for hatchery fish, 1993–2011, was substantially lower (0.733) than for their wild counterparts (0.888). Mean annual hatchery fish recapture rate, as a percentage of all 1992 cohort fish recaptures, declined significantly after age-7, coinciding with age of onset of migration into the open Gulf of Mexico. Hypothesized causal factors may be differentially lower fitness in the marine habitat or permanent outmigration due to natal river imprinting failure. Hatchery fish recapture rates varied significantly for fish from the ten release sites, being highest near the river mouth, and lowest for the furthest upriver sites in the Suwannee River and its Santa Fe River tributary. Hatchery fish also displayed a significantly lower growth rate than their wild counterparts through age 3000 days. Cumulative hatchery fish mortality of 99.87% over 19 years predicts <3 individuals would have survived through 2011. From the results of the 1992 release experiment, hatchery supplementation as a Gulf sturgeon conservation measure does not appear to be an effective option.

Release modeling and comparison of nanoarchaeosomal, nanoliposomal and pegylated nanoliposomal carriers for paclitaxel.

PubMed

Movahedi, Fatemeh; Ebrahimi Shahmabadi, Hasan; Alavi, Seyed Ebrahim; Koohi Moftakhari Esfahani, Maedeh

2014-09-01

Breast cancer is the most prevalent cancer among women. Recently, delivering by nanocarriers has resulted in a remarkable evolution in treatment of numerous cancers. Lipid nanocarriers are important ones while liposomes and archaeosomes are common lipid nanocarriers. In this work, paclitaxel was used and characterized in nanoliposomal and nanoarchaeosomal form to improve efficiency. To increase stability, efficiency and solubility, polyethylene glycol 2000 (PEG 2000) was added to some samples. MTT assay confirmed effectiveness of nanocarriers on MCF-7 cell line and size measuring validated nano-scale of particles. Nanoarchaeosomal carriers demonstrated highest encapsulation efficiency and lowest release rate. On the other hand, pegylated nanoliposomal carrier showed higher loading efficiency and less release compared with nanoliposomal carrier which verifies effect of PEG on improvement of stability and efficiency. Additionally, release pattern was modeled using artificial neural network (ANN) and genetic algorithm (GA). Using ANN modeling for release prediction, resulted in R values of 0.976, 0.989 and 0.999 for nanoliposomal, pegylated nanoliposomal and nanoarchaeosomal paclitaxel and GA modeling led to values of 0.954, 0.951 and 0.976, respectively. ANN modeling was more successful in predicting release compared with the GA strategy.

Contraceptive use in the Nordic countries.

PubMed

Lindh, Ingela; Skjeldestad, Finn E; Gemzell-Danielsson, Kristina; Heikinheimo, Oskari; Hognert, Helena; Milsom, Ian; Lidegaard, Øjvind

2017-01-01

The aim was to compare contraceptive use in the Nordic countries and to assess compliance with recommendations from the European Medicines Agency regarding the use of combined oral contraception containing low-dose estrogen and levonorgestrel, norethisterone or norgestimate. Data on hormonal contraceptive prescriptions and sales figures for copper intrauterine devices were obtained from national databases and manufacturers in Denmark, Finland, Iceland, Norway and Sweden in 2010-2013. Contraceptive use was highest in Denmark (42%) and Sweden (41%), followed by Finland (40%). Combined oral contraception was the most used method in all countries, with the highest use in Denmark (26%). The second most used method was the levonorgestrel-releasing intrauterine system, with the highest use in Finland (15%) and ≈10% in the other countries. Copper intrauterine devices (7%) and the progestin-only pill (7%) were most often used in Sweden. Combined oral contraception use decreased with increasing age and levonorgestrel-releasing intrauterine system and progestin-only pills use increased. The use of long-acting reversible methods of contraception (=levonorgestrel-releasing intrauterine system, copper intrauterine devices, and implants) increased with time and was highest in Sweden (20%) and Finland (18%). The highest use of European Medicines Agency recommended combined oral contraception was in Denmark, increasing from 13 to 50% between 2010 and 2013. In Finland, recommended combined oral contraception remained below 1%. Contraceptive use was highest in Denmark and Sweden, levonorgestrel-releasing intrauterine system use was highest in Finland and all long-acting methods were most common in Sweden. The use of combined oral contraception recommended by the European Medicines Agency was highest in Denmark. © 2016 Nordic Federation of Societies of Obstetrics and Gynecology.

Formulation and evaluation of novel controlled release of topical pluronic lecithin organogel of mefenamic acid.

PubMed

Jhawat, Vikas; Gupta, Sumeet; Saini, Vipin

2016-11-01

In the present study, pluronic lecithin based organogels (PLO gels) were formulated as topical carrier for controlled delivery of mefenamic acid. Ten organogel formulations were prepared by a method employing lecithin as lipophilic phase and pluronic F-127 as hydrophilic phase in varying concentrations to study various parameters using in vitro diffusion study and in vivo studies. All formulations were found to be off-white, homogenous, and reluctant to be washed easily and have pH value within the range of 5.56-5.80 which is nonirritant. Polymer concentration increased in formulations of F1 to F5 (lecithin) and F6 to F10 (pluronic) resulted in decrease of the gelation temperature, increase of viscosity and reduction of spreadability of gels having polymer tendency to form rigid 3D network. Organogels with higher viscosity were found to be more stable and retard the drug release from the gel. The formulations of F2 and F3 were selected for kinetic studies and stability studies, as they found to have all physical parameters within acceptable limits, highest percent drug content and exhibited highest drug release in eight hours. The order of drug release from various formulations was found to be F2 > F3 > F10 > F4 > F1 > F9 > F8 > F5 > F7 > F6. The optimized formulation F2 was found to follow zero order rate kinetics showing controlled release of the drug from the formulations. In vivo anti-inflammatory activity of optimized mefenamic acid organogel (F2) against a standard marketed preparation (Volini gel) was found satisfactory and significant.

Poverty and Education Report: Students Are Not to Blame--Understanding the Structural Causes of Family Poverty. BCTF Research Report. Section XII. 2009-EI-01

ERIC Educational Resources Information Center

White, Margaret

2009-01-01

In 2006, there were an estimated 181,000 low-income children in the province, with British Columbia (BC) reporting the highest before-tax child poverty rate (21.9%) in Canada (15.8%) for the fifth year in a row. This was the news in the "2008 Child Poverty Report Card" recently released by the First Call: BC Child and Youth Advocacy…

Greenhouse gas emissions from oilfield-produced water in Shengli Oilfield, Eastern China.

PubMed

Yang, Shuang; Yang, Wei; Chen, Guojun; Fang, Xuan; Lv, Chengfu; Zhong, Jiaai; Xue, Lianhua

2016-08-01

Greenhouse gas (GHG) emissions from oil and gas systems are an important component of the GHG emission inventory. To assess the carbon emissions from oilfield-produced water under atmospheric conditions correctly, in situ detection and simulation experiments were developed to study the natural release of GHG into the atmosphere in the Shengli Oilfield, the second largest oilfield in China. The results showed that methane (CH4) and carbon dioxide (CO2) were the primary gases released naturally from the oilfield-produced water. The atmospheric temperature and release time played important roles in determining the CH4 and CO2 emissions under atmospheric conditions. Higher temperatures enhanced the carbon emissions. The emissions of both CH4 and CO2 from oilfield-produced water were highest at 27°C and lowest at 3°C. The bulk of CH4 and CO2 was released from the oilfield-produced water during the first release period, 0-2hr, for each temperature, with a maximum average emission rate of 0.415gCH4/(m(3)·hr) and 3.934gCO2/(m(3)·hr), respectively. Then the carbon emissions at other time periods gradually decreased with the extension of time. The higher solubility of CO2 in water than CH4 results in a higher emission rate of CH4 than CO2 over the same release duration. The simulation proved that oilfield-produced water is one of the potential emission sources that should be given great attention in oil and gas systems. Copyright © 2016. Published by Elsevier B.V.

Effects of Holocene climate change on mercury deposition in Elk Lake, Minnesota: The importance of eolain transport in the mercury cycle

USGS Publications Warehouse

Cannon, W.F.; Dean, W.E.; Bullock, J.H.

2003-01-01

Sediments in Elk Lake, Minnesota, consist of 10,400 varve layers that provide a precise chronology for Holocene fluctuations in climate and biota recorded in the strata. Progressively greater concentrations and accumulation rates of mercury since ca. A.D. 1875 reflect deposition of anthropogenic mercury additions to the atmosphere. Within the Holocene record are numerous short intervals in which mercury concentrations and accumulation rates exceed the modern values. The highest mercury concentrations formed ca. 8 ka, coincident with a rapid change from cool, moist conditions to warm, dry conditions. A related change in flora from pine forest to prairie caused destruction of organic forest soils and the release of mercury that had been sequestered in them, resulting in a short- lived pulse of mercury to the lake. Accumulation rates of mercury were highest during the 4 k.y. mid-Holocene dry interval and show a correlation with periods of rapid deposition of eolian dust. The mercury was probably bound to wind-borne mineral particles, which were derived from an unidentified mercury-rich source region west of Elk Lake.

Protein S-glutathionylation lowers superoxide/hydrogen peroxide release from skeletal muscle mitochondria through modification of complex I and inhibition of pyruvate uptake.

PubMed

Gill, Robert M; O'Brien, Marisa; Young, Adrian; Gardiner, Danielle; Mailloux, Ryan J

2018-01-01

Protein S-glutathionylation is a reversible redox modification that regulates mitochondrial metabolism and reactive oxygen species (ROS) production in liver and cardiac tissue. However, whether or not it controls ROS release from skeletal muscle mitochondria has not been explored. In the present study, we examined if chemically-induced protein S-glutathionylation could alter superoxide (O2●-)/hydrogen peroxide (H2O2) release from isolated muscle mitochondria. Disulfiram, a powerful chemical S-glutathionylation catalyst, was used to S-glutathionylate mitochondrial proteins and ascertain if it can alter ROS production. It was found that O2●-/H2O2 release rates from permeabilized muscle mitochondria decreased with increasing doses of disulfiram (100-500 μM). This effect was highest in mitochondria oxidizing succinate or palmitoyl-carnitine, where a ~80-90% decrease in the rate of ROS release was observed. Similar effects were detected in intact mitochondria respiring under state 4 conditions. Incubation of disulfiram-treated mitochondria with DTT (2 mM) restored ROS release confirming that these effects were associated with protein S-glutathionylation. Disulfiram treatment also inhibited phosphorylating and proton leak-dependent respiration. Radiolabelled substrate uptake experiments demonstrated that disulfiram inhibited pyruvate import but had no effect on carnitine uptake. Immunoblot analysis of complex I revealed that it contained several protein S-glutathionylation targets including NDUSF1, a subunit required for NADH oxidation. Taken together, these results demonstrate that O2●-/H2O2 release from muscle mitochondria can be altered by protein S-glutathionylation. We attribute these changes to the protein S-glutathionylation complex I and inhibition of mitochondrial pyruvate carrier.

Protein S-glutathionylation lowers superoxide/hydrogen peroxide release from skeletal muscle mitochondria through modification of complex I and inhibition of pyruvate uptake

PubMed Central

Young, Adrian; Gardiner, Danielle

2018-01-01

Protein S-glutathionylation is a reversible redox modification that regulates mitochondrial metabolism and reactive oxygen species (ROS) production in liver and cardiac tissue. However, whether or not it controls ROS release from skeletal muscle mitochondria has not been explored. In the present study, we examined if chemically-induced protein S-glutathionylation could alter superoxide (O2●-)/hydrogen peroxide (H2O2) release from isolated muscle mitochondria. Disulfiram, a powerful chemical S-glutathionylation catalyst, was used to S-glutathionylate mitochondrial proteins and ascertain if it can alter ROS production. It was found that O2●-/H2O2 release rates from permeabilized muscle mitochondria decreased with increasing doses of disulfiram (100–500 μM). This effect was highest in mitochondria oxidizing succinate or palmitoyl-carnitine, where a ~80–90% decrease in the rate of ROS release was observed. Similar effects were detected in intact mitochondria respiring under state 4 conditions. Incubation of disulfiram-treated mitochondria with DTT (2 mM) restored ROS release confirming that these effects were associated with protein S-glutathionylation. Disulfiram treatment also inhibited phosphorylating and proton leak-dependent respiration. Radiolabelled substrate uptake experiments demonstrated that disulfiram inhibited pyruvate import but had no effect on carnitine uptake. Immunoblot analysis of complex I revealed that it contained several protein S-glutathionylation targets including NDUSF1, a subunit required for NADH oxidation. Taken together, these results demonstrate that O2●-/H2O2 release from muscle mitochondria can be altered by protein S-glutathionylation. We attribute these changes to the protein S-glutathionylation complex I and inhibition of mitochondrial pyruvate carrier. PMID:29444156

Formulation, characterization and pharmacokinetics of Morin hydrate niosomes prepared from various non-ionic surfactants.

PubMed

Waddad, Ayman Y; Abbad, Sarra; Yu, Fan; Munyendo, Were L L; Wang, Jing; Lv, Huixia; Zhou, Jianping

2013-11-18

Morin hydrate (MH), a bioflavonoid with antioxidant and anticancer activity as well as the ability to improve the bioavailability of other drugs on their concurrent use. Three differently optimized niosomal formulations using three different non-ionic surfactants (Span 60, Span 80 and Tween 60) were achieved by (L9 (3(4))) Taguchi orthogonal array (TOA). The analysis of TOA revealed that Tween 60 Niosomes had the highest entrapment efficiency (93.4%) compared to other optimized Niosomal formulations (71-79%). In terms of MH remaining %, Tween 60 Niosomes were found to be the most stable (89%) at 4 °C over one month compared to Span 60 (56%) and Span 80 (57%) Niosomes. The release pattern in all Niosomal formulations was found to follow the Weibull model and Tween 60 Niosomes had the highest release rate. The molecular modeling simulation explained the binding of MH to the human serum albumin (HSA) by hydrogen bonds during the in vitro release process. As for the bioavailability, the AUC0-8 showed 1.3-2.7 fold increase compared to the MH solution. Ex vivo images of the excised organs showed that MH could accumulate in brain which indicates that MH-Tween 60 Niosomes might be a possible candidate to deliver hydrophobic drugs and overcome the blood-brain barrier (BBB) penetration. Copyright © 2013 Elsevier B.V. All rights reserved.

Application of fuzzy c-means clustering to PRTR chemicals uncovering their release and toxicity characteristics.

PubMed

Xue, Mianqiang; Zhou, Liang; Kojima, Naoya; Dos Muchangos, Leticia Sarmento; Machimura, Takashi; Tokai, Akihiro

2018-05-01

Increasing manufacture and usage of chemicals have not been matched by the increase in our understanding of their risks. Pollutant release and transfer register (PRTR) is becoming a popular measure for collecting chemical data and enhancing the public right to know. However, these data are usually in high dimensionality which restricts their wider use. The present study partitions Japanese PRTR chemicals into five fuzzy clusters by fuzzy c-mean clustering (FCM) to explore the implicit information. Each chemical with membership degrees belongs to each cluster. Cluster I features high releases from non-listed industries and the household sector and high environmental toxicity. Cluster II is characterized by high reported releases and transfers from 24 listed industries above the threshold, mutagenicity, and high environmental toxicity. Chemicals in cluster III have characteristics of high releases from non-listed industries and low toxicity. Cluster IV is characterized by high reported releases and transfers from 24 listed industries above the threshold and extremely high environmental toxicity. Cluster V is characterized by low releases yet mutagenicity and high carcinogenicity. Chemicals with the highest membership degree were identified as representatives for each cluster. For the highest membership degree, half of the chemicals have a value higher than 0.74. If we look at both the highest and the second highest membership degrees simultaneously, about 94% of the chemicals have a value higher than 0.5. FCM can serve as an approach to uncover the implicit information of highly complex chemical dataset, which subsequently supports the strategy development for efficient and effective chemical management. Copyright © 2017 Elsevier B.V. All rights reserved.

Kinetic Studies of Calcium-Induced Calcium Release in Cardiac Sarcoplasmic Reticulum Vesicles

PubMed Central

Sánchez, Gina; Hidalgo, Cecilia; Donoso, Paulina

2003-01-01

Fast Ca2+ release kinetics were measured in cardiac sarcoplasmic reticulum vesicles actively loaded with Ca2+. Release was induced in solutions containing 1.2 mM free ATP and variable free [Ca2+] and [Mg2+]. Release rate constants (k) were 10-fold higher at pCa 6 than at pCa 5 whereas Ryanodine binding was highest at pCa ≤5. These results suggest that channels respond differently when exposed to sudden [Ca2+] changes than when exposed to Ca2+ for longer periods. Vesicles with severalfold different luminal calcium contents exhibited double exponential release kinetics at pCa 6, suggesting that channels undergo time-dependent activity changes. Addition of Mg2+ produced a marked inhibition of release kinetics at pCa 6 (K0.5 = 63 μM) but not at pCa 5. Coexistence of calcium activation and inhibition sites with equally fast binding kinetics is proposed to explain this behavior. Thimerosal activated release kinetics at pCa 5 at all [Mg2+] tested and increased at pCa 6 the K0.5 for Mg2+ inhibition, from 63 μM to 136 μM. We discuss the possible relevance of these results, which suggest release through RyR2 channels is subject to fast regulation by Ca2+ and Mg2+ followed by time-dependent regulation, to the physiological mechanisms of cardiac channel opening and closing. PMID:12668440

Preparation and pharmaceutical evaluation of glibenclamide slow release mucoadhesive buccal film

PubMed Central

Bahri-Najafi, R.; Tavakoli, N.; Senemar, M.; Peikanpour, M.

2014-01-01

Buccal mucoadhesive systems among novel drug delivery systems have attracted great attention in recent years due to their ability to adhere and remain on the oral mucosa and to release their drug content gradually. Buccal mucoadhesive films can improve the drug therapeutic effect by enhancement of drug absorption through oral mucosa increasing the drug bioavailability via reducing the hepatic first pass effect. The aim of the current study was to formulate the drug as buccal bioadhesive film, which releases the drug at sufficient concentration with a sustain manner reducing the frequency of the dosage form administration. One of the advantagees of this formulation is better patient compliances due to the ease of administration with no water to swallow the product. The mucoadhesive films of glibenclamide were prepared using hydroxypropyl methylcellulose (HPMC) K4M, K15M and Eudragit RL100 polymers and propylene glycol as plasticizer and co-solvent. Films were prepared using solvent casting method, and were evaluated with regard to drug content, thickness, weight variations, swelling index, tensile strength, ex vivo adhesion force and percentage of in vitro drug release. Films with high concentrations of HPMC K4M and K15M did not have favorable appearance and uniformity. The formulations prepared from Eudragit were transparent, uniform, flexible, and without bubble. The highest and the lowest percentages of swelling were observed for the films containing HPMC K15M and Eudragit RL100, respectively. Films made of HPMC K15M had adhesion force higher than those containing Eudragit RL100. Formulations with Eudragit RL100 showed the highest mean dissolution time (MDT). Drug release kinetics of all formulations followed Higuchi's model and the mechanism of diffusion was considered non-Fickian type. It was concluded that formulations containing Eudragit RL100 were more favorable than others with regard to uniformity, flexibility, rate and percentage of drug release. PMID:25657792

Feasibility of Using Gluconolactone, Trehalose and Hydroxy-Propyl Gamma Cyclodextrin to Enhance Bendroflumethiazide Dissolution Using Lyophilisation and Physical Mixing Techniques.

PubMed

Saleh, Ashraf; McGarry, Kenneth; Chaw, Cheng Shu; Elkordy, Amal Ali

2018-02-01

Hydrophobic drugs are facing a major challenge in dissolution rate enhancement and solubility in aqueous solutions; therefore, a variety of methods have been used to improve dissolution rate and/or solubility of bendroflumethiazide as a model hydrophobic drug. In this study, two main methods (physical mixing and lyophilisation) were used with gluconolactone, hydroxyl propyl γ-ccyclodextrin, and trehalose to explore this challenge. Bendroflumethiazide, practically insoluble in water, was mixed with one of the three excipients gluconolactone, hydroxyl propyl γ-cyclodextrin, and trehalose in three different ratios 1:1, 1:2, 1:5. To the best of our knowledge, the dissolution of the drug has not been previously enhanced by using either these methods or any of the used excipients. Samples containing drug and each of the excipients were characterized via dissolution testing, Fourier Transform infra-red spectroscopy, differential scanning calorimetry, and scanning electron microscopy. The used methods showed a significant enhancement in dug dissolution rate; physical mixing significantly, p < 0.05, increased the percentage of the drug released with time; for example, bendroflumethiazide dissolution in distilled water was improved from less than 20% to 99.79% within 90 min for physically mixed drug-cyclodextrin 1:5. The lyophilisation process was enhanced and the drug dissolution rate and the highest drug dissolution was achieved for (drug-gluconolactone 1:1) with 98.98% drug release within 90 min. the physical mixing and freeze drying processes significantly increased the percentage of drug release with time.

7 CFR Appendix B to Subpart E of... - Federal Reserve Statistical Release

Code of Federal Regulations, 2010 CFR

2010-01-01

....91 6.88 6.88 6.58 6.82 6.86 7.02 Finance paper placed directly 3,4,6 1-Month 6.76 6.85 6.83 6.83 6.55...) 14 8.29 8.26 8.29 8.27 8.15 8.25 8.28 8.33 Corporate bonds Moody's Seasoned AAA 9.03 9.01 9.00 8.99 8... directly placed by finance companies. 7 Representative closing yields for acceptances of the highest rated...

PEG-PE/clay composite carriers for doxorubicin: Effect of composite structure on release, cell interaction and cytotoxicity.

PubMed

Kohay, Hagay; Sarisozen, Can; Sawant, Rupa; Jhaveri, Aditi; Torchilin, Vladimir P; Mishael, Yael G

2017-06-01

A novel drug delivery system for doxorubicin (DOX), based on organic-inorganic composites was developed. DOX was incorporated in micelles (M-DOX) of polyethylene glycol-phosphatidylethanolamine (PEG-PE) which in turn were adsorbed by the clay, montmorillonite (MMT). The nano-structures of the PEG-PE/MMT composites of LOW and HIGH polymer loadings were characterized by XRD, TGA, FTIR, size (DLS) and zeta measurements. These measurements suggest that for the LOW composite a single layer of polymer intercalates in the clay platelets and the polymer only partially covers the external surface, while for the HIGH composite two layers of polymer intercalate and a bilayer may form on the external surface. These nanostructures have a direct effect on formulation stability and on the rate of DOX release. The release rate was reversely correlated with the degree of DOX interaction with the clay and followed the sequence: M-DOX>HIGH formulation>LOW formulation>DOX/MMT. Despite the slower release from the HIGH formulation, its cytotoxicity effect on sensitive cells was as high as the "free" DOX. Surprisingly, the LOW formulation, with the slowest release, demonstrated the highest cytotoxicity in the case of Adriamycin (ADR) resistant cells. Confocal microscopy images and association tests provided an insight into the contribution of formulation-cell interactions vs. the contribution of DOX release rate. Internalization of the formulations was suggested as a mechanism that increases DOX efficiency, particularly in the ADR resistant cell line. The employment of organic-inorganic hybrid materials as drug delivery systems, has not reached its full potential, however, its functionality as an efficient tunable release system was demonstrated. DOX PEG-PE/clay formulations were design as an efficient drug delivery system. The main aim was to develop PEG-PE/clay formulations of different structures based on various PEG-PE/clay ratios in order to achieve tunable release rates, to control the external surface characteristics and formulation stability. The formulations showed significantly higher toxicity in comparison to "free" DOX, explained by formulation internalization. For each cell line tested, sensitive and ADR resistant, a different formulation structure was found most efficient. The potential of PEG-PE/clay-DOX formulations to improve DOX administration efficacy was demonstrated and should be further explored and implemented for other cancer drugs and cells. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Compact drilling and sample system

NASA Technical Reports Server (NTRS)

Gillis-Smith, Greg R.; Petercsak, Doug

1998-01-01

The Compact Drilling and Sample System (CDSS) was developed to drill into terrestrial, cometary, and asteroid material in a cryogenic, vacuum environment in order to acquire subsurface samples. Although drills were used by the Apollo astronauts some 20 years ago, this drill is a fraction of the mass and power and operates completely autonomously, able to drill, acquire, transport, dock, and release sample containers in science instruments. The CDSS has incorporated into its control system the ability to gather science data about the material being drilled by measuring drilling rate per force applied and torque. This drill will be able to optimize rotation and thrust in order to achieve the highest drilling rate possible in any given sample. The drill can be commanded to drill at a specified force, so that force imparted on the rover or lander is limited. This paper will discuss the cryo dc brush motors, carbide gears, cryogenic lubrication, quick-release interchangeable sampling drill bits, percussion drilling and the control system developed to achieve autonomous, cryogenic, vacuum, lightweight drilling.

Effects of reaction conditions on the emission behaviors of arsenic, cadmium and lead during sewage sludge pyrolysis.

PubMed

Han, Hengda; Hu, Song; Syed-Hassan, Syed Shatir A; Xiao, Yiming; Wang, Yi; Xu, Jun; Jiang, Long; Su, Sheng; Xiang, Jun

2017-07-01

Sewage sludge is an important class of bioresources whose energy content could be exploited using pyrolysis technology. However, some harmful trace elements in sewage sludge can escape easily to the gas phase during pyrolysis, increasing the potential of carcinogenic material emissions to the atmosphere. This study investigates emission characteristics of arsenic, cadmium and lead under different pyrolysis conditions for three different sewage sludge samples. The increased temperature (within 723-1123K) significantly promoted the cadmium and lead emissions, but its influence on arsenic emission was not pronounced. The releasing rate order of the three trace elements is volatile arsenic compounds>cadmium>lead in the beginning of pyrolysis. Fast heating rates promoted the emission of trace elements for the sludge containing the highest amount of ash, but exhibited an opposite effect for other studied samples. Overall, the high ash sludge released the least trace elements almost under all reaction conditions. Copyright © 2017 Elsevier Ltd. All rights reserved.

A novel chitosan-polyethylene oxide nanofibrous mat designed for controlled co-release of hydrocortisone and imipenem/cilastatin drugs.

PubMed

Fazli, Yousef; Shariatinia, Zahra; Kohsari, Iraj; Azadmehr, Amirreza; Pourmortazavi, Seied Mahdi

2016-11-20

Antimicrobial chitosan-polyethylene oxide (CS-PEO) nanofibrous mats containing ZnO nanoparticles (NPs) and hydrocortisone-imipenem/cilastatin-loaded ZnO NPs were produced by electrospinning technique. The FE-SEM images displayed that the spherical ZnO NPs were ∼70-200nm in size and the CS-PEO nanofibers were very uniform and free of any beads which had average diameters within the range of ∼20-130nm. For all of the nanofibrous mats, the water uptakes were the highest in acidic medium but they were decreased in the buffer and the least swellings were obtained in the alkaline environment. The drug incorporated mat preserved its bactericidal activity even after it was utilized in the release experiment for 8days in the PBS buffer. The hydrocortisone release was increased to 82% within first 12h while the release rate of imipenem/cilastatin was very much slower so that 20% of the drug was released during this period of time suggesting this nanofibrous mat is very suitable to inhibit inflammation (by hydrocortisone) and infection (using imipenem/cilastatin antibiotic and ZnO NPs) principally for the wound dressing purposes. Copyright © 2016 Elsevier B.V. All rights reserved.

Rheological behavior and Ibuprofen delivery applications of pH responsive composite alginate hydrogels.

PubMed

Jabeen, Suraya; Maswal, Masrat; Chat, Oyais Ahmad; Rather, Ghulam Mohammad; Dar, Aijaz Ahmad

2016-03-01

Synthesis and structural characterization of hydrogels composed of sodium alginate, polyethylene oxide and acrylic acid with cyclodextrin as the hydrocolloid prepared at different pH values is presented. The hydrogels synthesized show significant variations in rheological properties, drug encapsulation capability and release kinetics. The hydrogels prepared at lower pH (pH 1) are more elastic, have high tensile strength and remain almost unaffected by varying temperature or frequency. Further, their Ibuprofen encapsulation capacity is low and releases it slowly. The hydrogel prepared at neutral pH (pH 7) is viscoelastic, thermo-reversible and also exhibits sol-gel transition on applying frequency and changing temperature. It shows highest Ibuprofen encapsulation capacity and also optimum drug release kinetics. The hydrogel prepared at higher pH (pH 12) is more viscous, has low tensile strength, is unstable to change in temperature and has fast drug release rate. The study highlights the pH responsiveness of three composite alginate hydrogels prepared under different conditions to be employed in drug delivery applications. Copyright © 2015 Elsevier B.V. All rights reserved.

Spall response of single-crystal copper

NASA Astrophysics Data System (ADS)

Turley, W. D.; Fensin, S. J.; Hixson, R. S.; Jones, D. R.; La Lone, B. M.; Stevens, G. D.; Thomas, S. A.; Veeser, L. R.

2018-02-01

We performed a series of systematic spall experiments on single-crystal copper in an effort to determine and isolate the effects of crystal orientation, peak stress, and unloading strain rate on the tensile spall strength. Strain rates ranging from 0.62 to 2.2 × 106 s-1 and peak shock stresses in the 5-14 GPa range, with one additional experiment near 50 GPa, were explored as part of this work. Gun-driven impactors, called flyer plates, generated flat top shocks followed by spall. This work highlights the effect of crystal anisotropy on the spall strength by showing that the spall strength decreases in the following order: [100], [110], and [111]. Over the range of stresses and strain rates explored, the spall strength of [100] copper depends strongly on both the strain rate and shock stress. Except at the very highest shock stress, the results for the [100] orientation show linear relationships between the spall strength and both the applied compressive stress and the strain rate. In addition, hydrodynamic computer code simulations of the spall experiments were performed to calculate the relationship between the strain rate near the spall plane in the target and the rate of free surface velocity release during the pullback. As expected, strain rates at the spall plane are much higher than the strain rates estimated from the free surface velocity release rate. We have begun soft recovery experiments and molecular dynamics calculations to understand the unusual recompression observed in the spall signature for [100] crystals.

Iron and copper release in drinking-water distribution systems.

PubMed

Shi, Baoyou; Taylor, James S

2007-09-01

A large-scale pilot study was carried out to evaluate the impacts of changes in water source and treatment process on iron and copper release in water distribution systems. Finished surface waters, groundwaters, and desalinated waters were produced with seven different treatment systems and supplied to 18 pipe distribution systems (PDSs). The major water treatment processes included lime softening, ferric sulfate coagulation, reverse osmosis, nanofiltration, and integrated membrane systems. PDSs were constructed from PVC, lined cast iron, unlined cast iron, and galvanized pipes. Copper pipe loops were set up for corrosion monitoring. Results showed that surface water after ferric sulfate coagulation had low alkalinity and high sulfates, and consequently caused the highest iron release. Finished groundwater treated by conventional method produced the lowest iron release but the highest copper release. The iron release of desalinated water was relatively high because of the water's high chloride level and low alkalinity. Both iron and copper release behaviors were influenced by temperature.

Comparison of catch and lake trout bycatch in commercial trap nets and gill nets targeting lake whitefish in northern Lake Huron

USGS Publications Warehouse

Johnson, James E.; Ebener, Mark P.; Gebhardt, Kenneth; Bergstedt, Roger

2004-01-01

We compared seasonal lake whitefish catch rates, lake trout bycatch, and gearinduced lake trout mortality between commercial trap nets and gill nets in north-central Lake Huron. Onboard monitors recorded catches from 260 gill net and 96 trap net lifts from October 1998 through December 1999. Catch rates for lake whitefish were highest in fall for both gear types, reflecting proximity of spawning sites to the study area. Lake whitefish catch rates were also relatively high in spring but low in both gear types in summer. Lake trout were the principal bycatch species in both gears. The lake trout bycatch was lowest in both gear types in fall, highest in gill nets in spring, and highest in trap nets in summer. The ratio of lake trout to legal whitefish (the target species) was highest in summer and lowest in fall in both gear types. The high lake trout ratio in summer was due principally to low catch rates of lake whitefish. All but 3 of 186 live lake trout removed from trap net pots survived for at least two days of observation in laboratory tanks. Therefore, we estimated that post-release survival of trap netted lake trout that had not been entangled in the mesh was 98.4%. In addition, we accounted for stress-induced mortality for lake trout that were live at capture but entangled in the mesh of either gear type. Resulting estimates of lake trout survival were higher in trap nets (87.8%) than in gill nets (39.6%). The number of lake trout killed per lift was highest during summer in trap nets and during spring in gill nets. In trap nets, 85% of dead lake trout were observed to be entangled in the mesh of the pot or tunnels. Survival rates of lake trout in gill nets were higher in our study than reported by others, probably because our nets were hand lifted in a small boat. Our trap net-induced mortality estimates on lake trout were higher than those reported by others because we adjusted our estimates to account for post-release mortality caused by handling and injury. Studies such as ours should prove useful to managers developing harvest allocation options that are consistent with the need to protect nontarget populations. For example, applying our seasonal lake trout-whitefish catch ratios to a hypothetical small-boat gill net fishery, the lake trout bycatch from harvest of 100,000 kg of whitefish would equal the estimated lake trout production available for harvest in the study area for year 2002. The two trap net fisheries may have incidentally killed half this number of lake trout annually from 1995-99. Bycatch estimates are also important inputs to catch-at-age decision models used in developing rehabilitation and harvest strategies for target and bycatch species.

Detailed source term estimation of atmospheric release during the Fukushima Dai-ichi nuclear power plant accident by coupling atmospheric and oceanic dispersion models

NASA Astrophysics Data System (ADS)

Katata, Genki; Chino, Masamichi; Terada, Hiroaki; Kobayashi, Takuya; Ota, Masakazu; Nagai, Haruyasu; Kajino, Mizuo

2014-05-01

Temporal variations of release amounts of radionuclides during the Fukushima Dai-ichi Nuclear Power Plant (FNPP1) accident and their dispersion process are essential to evaluate the environmental impacts and resultant radiological doses to the public. Here, we estimated a detailed time trend of atmospheric releases during the accident by combining environmental monitoring data and coupling atmospheric and oceanic dispersion simulations by WSPEEDI-II (Worldwide version of System for Prediction of Environmental Emergency Dose Information) and SEA-GEARN developed by the authors. New schemes for wet, dry, and fog depositions of radioactive iodine gas (I2 and CH3I) and other particles (I-131, Te-132, Cs-137, and Cs-134) were incorporated into WSPEEDI-II. The deposition calculated by WSPEEDI-II was used as input data of ocean dispersion calculations by SEA-GEARN. The reverse estimation method based on the simulation by both models assuming unit release rate (1 Bq h-1) was adopted to estimate the source term at the FNPP1 using air dose rate, and air sea surface concentrations. The results suggested that the major release of radionuclides from the FNPP1 occurred in the following periods during March 2011: afternoon on the 12th when the venting and hydrogen explosion occurred at Unit 1, morning on the 13th after the venting event at Unit 3, midnight on the 14th when several openings of SRV (steam relief valve) were conducted at Unit 2, morning and night on the 15th, and morning on the 16th. The modified WSPEEDI-II using the newly estimated source term well reproduced local and regional patterns of air dose rate and surface deposition of I-131 and Cs-137 obtained by airborne observations. Our dispersion simulations also revealed that the highest radioactive contamination areas around FNPP1 were created from 15th to 16th March by complicated interactions among rainfall (wet deposition), plume movements, and phase properties (gas or particle) of I-131 and release rates associated with reactor pressure variations in Units 2 and 3.

Reservoir water level drawdown as a novel, substantial, and manageable control on methane release to the atmosphere

NASA Astrophysics Data System (ADS)

Harrison, J.; Deemer, B. R.; Birchfield, M. K.

2014-12-01

Reservoirs constitute a globally important source of atmospheric methane (CH4). Although it is reasonably well-established that hydrostatic and barometric pressure can influence rates of CH4 release from lake and tidal sediments, the relationship between water-level manipulation and CH4 release from man-made impoundments has not been quantified or characterized. Furthermore, cross-system controls on CH4 production and release to the atmosphere have not been established. We collected CH4 emission (diffusion and ebullition) data for 8 reservoirs in the U.S. Pacific Northwest that are subject to a range of trophic conditions and water level management regimes. Our aim was to: (1) characterize CH4 emissions from these systems, and (2) quantify effects of water level management and eutrophication on CH4 fluxes. Results indicate very high fluxes, in some cases the highest reported reservoir emission rates, and a strong correspondence between lake level reduction and CH4 emissions, including quantitatively important bursts of CH4 bubbling. In one reservoir, drawdown-associated CH4 fluxes accounted for over 25% of annual CH4 emissions in a period of just 16 days (4% of the year). Average CH4 ebullition rates in a reservoir managed for hydropower peaking were nearly three-fold higher than in a paired upstream reservoir managed to maintain a constant water level (528 mg CH4 m-2 d-1 and 187 mg CH4 m-2 d-1 respectively). Highest gas fluxes were observed during the water level drawdown component of the hydropower peaking cycle (14.3 g CH4 m-2 d-1). In addition we observe a strong, positive relationship between eutrophication (as indicated by surface Chl a concentrations) and CH4 production (r2 = 0.88; P<0.001) and between eutrophication and the sensitivity of CH4 emissions to drawdown (r2 = 0.84; P<0.001). This work suggests that manipulation of water levels can significantly affect CH4 emissions from reservoirs to the atmosphere, and that sampling programs that miss drawdown periods may substantially underestimate CH4 fluxes. It also suggests that controlling nutrient loading may reduce greenhouse gas fluxes from surface waters to the atmosphere.

Ion release from dental casting alloys as assessed by a continuous flow system: Nutritional and toxicological implications.

PubMed

López-Alías, José F; Martinez-Gomis, Jordi; Anglada, Josep M; Peraire, Maria

2006-09-01

The aims of this study were to quantify the metallic ions released by various dental alloys subjected to a continuous flow of saliva and to estimate the nutritional and toxicological implications of such a release. Four pieces of three nickel-based, one noble, one high-noble and two copper-aluminum alloys were cast and then immersed in a continuous flow of artificial saliva for 15 days. To simulate three meals a day, casts were subjected to thrice-daily episodes, lasting 30 min each and consisting of pH decreases and salinity increases. After 15 days, the metallic ions in the artificial saliva were analyzed. Data were expressed as averaged release rate: microg/cm2/day of ion released for each alloy. The highest value of 95% Cl of each ion was adapted to a hypothetical worst scenario of a subject with 100 cm2 of exposed metal surface. The results were compared with the tolerable upper daily intake level of each ion. The copper-aluminum alloys released copper, aluminum, nickel, manganese and iron. The nickel-based alloys essentially released nickel and chromium, while the beryllium-containing alloy released beryllium and significantly more nickel. The noble and high-noble alloys were very resistant to corrosion. The amount of ions released remained far below the upper tolerable intake level, with the exception of nickel, released by beryllium-containing nickel-based alloy, whose levels approach 50% of this threshold. The daily amount of ions released seems to be far below the tolerable upper intake levels for each ion.

Efficacy of the Levonorgestrel-Releasing Intrauterine System on IVF-ET Outcomes in PCOS With Simple Endometrial Hyperplasia.

PubMed

Bian, Jiang; Shao, Hongfang; Liu, Hua; Li, Hui; Fang, Lu; Xing, Changying; Wang, Lihong; Tao, Minfang

2015-06-01

This study investigated the in vitro fertilization (IVF) outcome of levonorgestrel-releasing intrauterine system (LNG-IUS) pretreatment for simple endometrial hyperplasia (EH) in patients with polycystic ovary syndrome (PCOS) undergoing IVF embryo transfer (IVF-ET). One hundred ninety patients with PCOS and simple EH without cytologic atypia were allocated randomly to 2 independent arms, that is, the LNG-IUS group (90 patients) and the non-LNG-IUS group (100 patients). Four hundred fourteen patients with PCOS without endometrial disease comprised the control group. Each patient was reevaluated by transvaginal ultrasonography (TVS) and endometrial biopsy after 6 months. For each patient, IVF outcome measures, such as number of recombinant follicle-stimulating hormone, endometrial thickness on human chorionic gonadotropin (HCG) day, hormone levels (progesterone, luetinizing hormone, and serum estradiol) on HCG day, number of oocytes, fertilization rate, clinical pregnancy rate, and miscarriage rate were compared among the 3 groups. In general, the 3 groups did not differ with respect to the main clinical and biochemical data. After 6 months, patients in LNG-IUS group had an EH resolution rate of 87.77%. In the non-LNG-IUS group, the resolution rate was 15.00%, and 3% of these patients showed progression of EH. The clinical pregnancy rates in the non-LNG-IUS group were significantly lower (28.04%) than that in the LNG-IUS group (46.06%) and the control group (44.65%). The miscarriage rate was highest in the non-LNG-IUS group, but no significant difference in miscarriage rate existed among the 3 groups. The study illustrates that the LNG-IUS can be safely used for 6 months as a treatment for patients with PCOS and simple EH. Additionally, use of the LNG-IUS can increase the clinical pregnancy rates and implantation rates of patients with PCOS and simple EH who undergo gonadotropin-releasing hormone agonist IVF-ET protocols. © The Author(s) 2014.

Thai Silk Fibroin/Gelatin Sponges for the Dual Controlled Release of Curcumin and Docosahexaenoic Acid for Anticancer Treatment.

PubMed

Lerdchai, Kantarat; Kitsongsermthon, Jutarat; Ratanavaraporn, Juthamas; Kanokpanont, Sorada; Damrongsakkul, Siriporn

2016-01-01

In this study, curcumin and/or docosahexaenoic acid (DHA) were encapsulated in Thai silk fibroin/gelatin (SF/G) sponges, prepared at different blending ratios, aimed to be applied as a controlled release system for localized cancer therapy. The SF/G sponges were fabricated by freeze-drying and glutaraldehyde cross-linking techniques. Physicochemical properties of the SF/G sponges were characterized. Then, curcumin and/or DHA were loaded in the sponges by physical adsorption. The encapsulation efficiency and the in vitro release of curcumin and/or DHA from the sponges were evaluated. SF/G sponges could encapsulate curcumin and/or DHA at high encapsulation efficiency. The highly cross-linked and slowly degrading SF/G (50/50) sponge released curcumin and/or DHA at the slowest rate. The in vitro cytotoxicity of the sponges against noncancer cells (L929 mouse fibroblast) and anticancer of curcumin and/or DHA released from the sponges against cervical cancer cells (CaSki) were tested. All sponges were not toxic to L929 mouse fibroblast. The mixed curcumin–DHA at the ratio of 1:4 had the highest inhibiting effect on the growth of CaSki, comparing with the release of curcumin or DHA alone. SF/G sponges could be a potential carrier for dual release of curcumin and DHA for anticancer effect.

Release of Oxidized Bromine Species From Diatoms: Implication for the Polar Troposphere and Oceanic Polyhalomethane Production

NASA Astrophysics Data System (ADS)

Manley, S. L.; Hill, V. L.

2006-12-01

Marine and ice diatoms are known producers of polybromomethanes. These trace gases produced from ice algae have been implicated as a source of photochemically active bromine involved in polar surface ozone depletion events. A more dominant source of reactive bromine, however, has been attributed to the reaction on ice particles and in sea spray aerosols of atmospherically derived HOBr with bromide and chloride to produce the dihalogens Br2 and BrCl. We have measured the release of oxidized bromine species (Brox = HOBr, Br2, Br3-1) from polar and temperate diatoms. The highest rates were measured from Porosira glaciales (CCMP 651). Release rates are range from 0.84 to 180 fmoles bromine/hour/cell depending on the species or an approximate maximum of 950 nmoles bromine/mg chl a/hr (P. glaciales). The flux from the diatoms is 0.1 to 7.5 nmoles bromine/cm2 diatom surface/hr. This release occurs from an extracellular bromoperoxidase when a suitable organic substrate is absent. At 0.84 mM bromide (average seawater concentration), the optimal pH for Brox release is 6.5, which is the putative pH of the apoplastic space, and the optimal H2O2 concentration is 250 nM. Based on these results, it is estimated that the amount of bromine released from ice algae as Brox is 10 to 200 times greater than the release of bromine as bromoform from ice algae. The Brox so produced could participate in the abiotic formation of dihalogens in sea ice. Also, Brox released from diatoms may react with specific components of DOC, if present, to indirectly produce polybromomethanes both in sea ice and seawater. The amount of polyhalomethanes produced is not only dependent on the algal species present but also on the composition of DOC.

Galantamine-ER for the treatment of mild-to-moderate Alzheimer’s disease

PubMed Central

Seltzer, Ben

2010-01-01

An extended release form of the cholinesterase inhibitor (ChEI) drug galantamine (galantamine-ER) was developed, chiefly to increase adherence to medication regimes in patients with mild-to-moderate Alzheimer’s disease (AD). Except for predicted differences in (Cmax) and tmax, comparable doses of once daily galantamine-ER and regular, immediate release galantamine, (galantamine-IR), are pharmacologically equivalent. A 24-week randomized, double-blind, placebo-and active-controlled, multicenter phase III trial, which compared galantamine-IR, galantamine-ER and placebo in subjects with mild to moderate AD (mini-mental state examination [MMSE] score range, 10 to 24) showed that both formulations of galantamine were significantly better than placebo in terms of cognition, although not with regard to global change. There was no difference in drug-related adverse events between galantamine-ER and galantamine-IR. Since its release onto the market galantamine-ER has enjoyed wide popularity and a recent surveillance study suggests that it has the highest 1-year persistence rate of all the ChEIs. PMID:20169037

Microencapsulation of essential oil for insect repellent in food packaging system.

PubMed

Chung, Seong Kyun; Seo, Ji Yeon; Lim, Jung Hoon; Park, Hyung Hwan; Yea, Myeong Jai; Park, Hyun Jin

2013-05-01

Microcapsules containing thyme oil were prepared by in situ polymerization, using melamine-formaldehyde prepolymer as a wall material and 3 different emulsifiers (pluronic F-127, tween 80, and sodium lauryl sulfate [SLS]). The general characteristics and release behavior of microcapsules, and their repellent effect against insects were investigated. The morphology of microcapsules using SLS was spherical shape with smooth surface. Microcapsules began to degrade at 150 °C. The particle size ranged from 1 to 10 μm and the loading efficiency of thyme oil was clearly affected by the emulsifier type. The highest loading efficiency appeared in microcapsules using SLS, which have good thermal resistance and smooth surface. The release rate of thyme oil from microcapsules was not only dependent on the storage temperature but also emulsifier type and microcapsules showed the sustained release properties for a long time. Diets, which were mixed with encapsulated thyme oil, expressed high insect repellent efficacy over 90% for 4 wk. © 2013 Institute of Food Technologists®

Atmospheric contribution of gas emissions from Augustine volcano, Alaska during the 2006 eruption

USGS Publications Warehouse

McGee, K.A.; Doukas, M.P.; McGimsey, R.G.; Neal, C.A.; Wessels, R.L.

2008-01-01

Airborne surveillance of gas emissions from Augustine for SO2, CO2 and H2S showed no evidence of anomalous degassing from 1990 through May 2005. By December 20, 2005, Augustine was degassing 660 td-1 of SO2, and ten times that by January 4, 2006. The highest SO2 emission rate measured during the 2006 eruption was 8650 td-1 (March 1); for CO2, 13000 td-1 (March 9), and H2S, 8 td-1 (January 19). Thirty-four SO2 measurements were made from December 2005 through 2006, with 9 each for CO2 and H2S. Augustine released 1 ?? 106 tonnes of CO2 to the atmosphere during 2006, a level similar to the output of a medium-sized natural gas-fired power plant, and thus was not a significant contributor of greenhouse gas to the atmosphere compared to anthropogenic sources. Augustine released about 5 ?? 105 tonnes of SO2 during 2006, similar to that released in 1976 and 1986.

Downstream migration and multiple dam passage by Atlantic Salmon smolts

USGS Publications Warehouse

Nyqvist, D.; McCormick, Stephen; Greenberg, L.; Ardren, W.R.; Bergman, E.; Calles, O.; Castro-Santos, Theodore R.

2017-01-01

The purpose of this study was to investigate behavior and survival of radio-tagged wild and hatchery-reared landlocked Atlantic Salmon Salmo salar smolts as they migrated past three hydropower dams equipped with fish bypass solutions in the Winooski River, Vermont. Among hatchery-reared smolts, those released early were more likely to initiate migration and did so after less delay than those released late. Once migration was initiated, however, the late-released hatchery smolts migrated at greater speeds. Throughout the river system, hatchery-reared fish performed similarly to wild fish. Dam passage rates varied between the three dams and was highest at the dam where unusually high spill levels occurred throughout the study period. Of the 50 fish that did migrate downstream, only 10% managed to reach the lake. Migration success was low despite the presence of bypass solutions, underscoring the need for evaluations of remedial measures; simply constructing a fishway is not synonymous with providing fish passage.

Operational level for unconditional release of contaminated property from affected areas around Fukushima Daiichi nuclear power plant

PubMed Central

Ogino, Haruyuki; Hattori, Takatoshi

2013-01-01

This paper focuses on the surface contamination control of slightly contaminated property after the Fukushima nuclear accident. The operational level for the unconditional release of contaminated properties is calculated in counts per minute (cpm) to enable the use of a typical Geiger-Muller (GM) survey meter with a 50-mm bore, on the basis of the surficial clearance level of 10 Bq cm−2 for 134Cs and 137Cs derived in the previous studies of the authors. By applying a factor for the conversion of the unit surface contamination to the count rate of a survey meter widely used after the Fukushima accident, the operational level for the unconditional release of contaminated properties was calculated to be 2300 cpm on average and 23 000 cpm at the highest-contamination part. The calculated numerical values of the operational levels are effective as long as the typical GM survey meter is used in the radiation measurement. PMID:23778575

A Multifunctional Coating for Autonomous Corrosion Control

NASA Technical Reports Server (NTRS)

Calle, L. M.; Hintze, P. E.; Li, W.; Buhrow, J. W.; Jolley, S. T.

2011-01-01

This slide presentation reviews the effects of corrosion on various structures at the Kennedy Space Center, and the work to discover a corrosion control coating that will be autonomous and will indicate corrosion at an early point in the process. Kennedy Space Center has many environmental conditions that are corrosive: ocean salt spray, heat, humidity, sunlight and acidic exhaust from the Solid Rocket Boosters (SRBs). Presented is a chart which shows the corrosion rates of carbon steel at various locations. KSC has the highest corrosion rates with 42.0 mils/yr, leading the next highest Galeta Point Beach, in the Panama Canal Zone with 27 mils/yr corrosion. A chart shows the changes in corrosion rate with the distance from the ocean. The three types of corrosion protective coatings are described: barrier (passive), Barrier plus active corrosion inhibiting components, and smart. A smart coating will detect and respond actively to changes in its environment in a functional and predictable manner and is capable of adapting its properties dynamically. The smart coating uses microcapsules, particles or liquid drops coated in polymers, that can detect and control the corrosion caused by the environment. The mechanism for a pH sensitive microcapsule and the hydrophobic core microcapsule are demonstrated and the chemistry is reviewed. When corrosion begins, the microcapsule will release the contents of the core (indicator, inhibitor, and self healing agent) in close proximity to the corrosion. The response to a pH increase is demonstrated by a series of pictures that show the breakdown of the microcapsule and the contents release. An example of bolt corrosion is used, as an example of corrosion in places that are difficult to ascertain. A comparison of various coating systems is shown.

The Risk of Opioid Intoxications or Related Events and the Effect of Alcohol-Related Disorders: A Retrospective Cohort Study in German Patients Treated with High-Potency Opioid Analgesics.

PubMed

Jobski, K; Kollhorst, B; Schink, T; Garbe, Edeltraut

2015-09-01

Intoxications involving prescription opioids are a major public health problem in many countries. When taken with opioids, alcohol can enhance the effects of opioids, particularly in the central nervous system. However, data quantifying the impact of alcohol involvement in opioid-related intoxications are limited. Using claims data from the German Pharmacoepidemiological Research Database (GePaRD), we conducted a retrospective cohort study based on users of high-potency opioid (HPO) analgesics during the years 2005-2009. HPO use was classified as extended-release, immediate-release or both. We calculated incidence rates (IRs) for opioid intoxications or related events as well as adjusted IR ratios (aIRR) comparing HPO-treated patients with alcohol-related disorders (ARDs) to those without ARDs overall and within each HPO category. During the study period, 308,268 HPO users were identified with an overall IR of 340.4 per 100,000 person-years [95 % confidence interval (CI) 325.5-355.7]. The risk was highest when patients received concomitant treatment with extended- and immediate-release HPOs (IR 1093.8; 95 % CI 904.6-1310.9). ARDs increased the risk during HPO use by a factor of 1.7 and the highest aIRR was seen when comparing patients simultaneously exposed to extended- and immediate-release HPOs with ARDs to those without ARD also after excluding patients with potential improper/non-medical HPO use. Physicians should be aware of these elevated risks in HPO patients with ARDs. Active patient education by healthcare providers regarding the risk of opioid intoxications or related events due to alcohol in conjunction with HPOs is warranted.

Kinetic characterization of a novel endo-β-N-acetylglucosaminidase on concentrated bovine colostrum whey to release bioactive glycans.

PubMed

Karav, Sercan; Parc, Annabelle Le; de Moura Bell, Juliana Maria Leite Nobrega; Rouquié, Camille; Mills, David A; Barile, Daniela; Block, David E

2015-09-01

EndoBI-1 is a recently isolated endo-β-N-acetylglucosaminidase, which cleaves the N-N'-diacetyl chitobiose moiety found in the N-glycan core of high mannose, hybrid and complex N-glycans. These N-glycans have selective prebiotic activity for a key infant gut microbe, Bifidobacterium longum subsp. infantis. The broad specificity of EndoBI-1 suggests the enzyme may be useful for many applications, particularly for deglycosylating milk glycoproteins in dairy processing. To facilitate its commercial use, we determined kinetic parameters for EndoBI-1 on the model substrates ribonuclease B and bovine lactoferrin, as well as on concentrated bovine colostrum whey. Km values ranging from 0.25 to 0.49, 0.43 to 1.00 and 0.90 to 3.18 mg/mL and Vmax values ranging from 3.5×10(-3) to 5.09×10(-3), 4.5×10(-3) to 7.75×10(-3) and 1.9×10(-2)to 5.2×10(-2) mg/mL×min were determined for ribonuclease B, lactoferrin and whey, respectively. In general, EndoBI-1 showed the highest apparent affinity for ribonuclease B, while the maximum reaction rate was the highest for concentrated whey. EndoBI-1-released N-glycans were quantified by a phenol-sulphuric total carbohydrate assay and the resultant N-glycan structures monitored by nano-LC-Chip-Q-TOF MS. The kinetic parameters and structural characterization of glycans released suggest EndoBI-1 can facilitate large-scale release of complex, bioactive glycans from a variety of glycoprotein substrates. Moreover, these results suggest that whey, often considered as a waste product, can be used effectively as a source of prebiotic N-glycans. Copyright © 2015. Published by Elsevier Inc.

Physicochemical Characteristics and Slow Release Performances of Chlorpyrifos Encapsulated by Poly(butyl acrylate-co-styrene) with the Cross-Linker Ethylene Glycol Dimethacrylate.

PubMed

Wang, Yu; Gao, Zideng; Shen, Feng; Li, Yang; Zhang, Sainan; Ren, Xueqin; Hu, Shuwen

2015-06-03

Chlorpyrifos' application and delivery to the target substrate needs to be controlled to improve its use. Herein, poly(butyl acrylate-co-styrene) (poly(BA/St)) and poly(BA/St/ethylene glycol dimethacrylate (EGDMA)) microcapsules loaded with chlorpyrifos as a slow release formulation were prepared by emulsion polymerization. The effects of structural characteristics on the chlorpyrifos microcapsule particle size, entrapment rate (ER), pesticide loading (PL), and release behaviors in ethyl alcohol were investigated. Fourier transform infrared and thermogravimetric analysis confirmed the successful entrapment of chlorpyrifos. The ER and PL varied with the BA/St monomer ratio, chlorpyrifos/monomer core-to-shell ratio, and EGDMA cross-linker content with consequence that suitable PL was estimated to be smaller than 3.09% and the highest ER was observed as 96.74%. The microcapsule particle size (88.36-101.8 nm) remained mostly constant. The extent of sustainable release decreased with increasing content of BA, St, or chlorpyrifos in the oil phase. Specifically, an adequate degree of cross-linking with EGMDA (0.5-2.5%) increased the extent of sustainable release considerably. However, higher levels of cross-linking with EGDMA (5-10%) reduced the extent of sustainable release. Chlorpyrifos release from specific microcapsules (monomer ratio 1:2 with 0.5% EGDMA or 5 g chlopyrifos) tended to be a diffusion-controlled process, while for others, the kinetics probably indicated the initial rupture release.

Evaluation of hydrophobic materials as matrices for controlled-release drug delivery.

PubMed

Quadir, Mohiuddin Abdul; Rahman, M Sharifur; Karim, M Ziaul; Akter, Sanjida; Awkat, M Talat Bin; Reza, Md Selim

2003-07-01

The present study was undertaken to evaluate the effect of different insoluble and erodable wax-lipid based materials and their content level on the release profile of drug from matrix systems. Matrix tablets of theophylline were prepared using carnauba wax, bees wax, stearic acid, cetyl alcohol, cetostearyl alcohol and glyceryl monostearate as rate-retarding agents by direct compression process. The release of theophylline from these hydrophobic matrices was studied over 8-hours in buffer media of pH 6.8. Statistically significant difference was found among the drug release profile from different matrices. The release kinetics was found to be governed by the type and content of hydrophobic materials in the matrix. At lower level of wax matrices (25%), a potential burst release was observed with all the materials being studied. Bees wax could not exert any sustaining action while an extensive burst release was found with carnauba wax at this hydrophobic load. Increasing the concentration of fat-wax materials significantly decreased the burst effect of drug from the matrix. At higher hydrophobic level (50% of the matrix), the rate and extent of drug release was significantly reduced due to increased tortuosity and reduced porosity of the matrix. Cetostearyl alcohol imparted the strongest retardation of drug release irrespective of fat-wax level. Numerical fits indicate that the Higuchi square root of time model was the most appropriate one for describing the release profile of theophylline from hydrophobic matrices. The release mechanism was also explored and explained with biexponential equation. Application of this model indicates that Fickian or case I kinetics is the predominant mechanism of drug release from these wax-lipid matrices. The mean dissolution time (MDT) was calculated for all the formulations and the highest MDT value was obtained with cetostearyl matrix. The greater sustaining activity of cetostearyl alcohol can be attributed to some level of swelling and erosion within this matrix at lower fat-wax level which is also supported by release exponent values and Fickian fraction release against time profile of this agent. The results generated in this study showed that proper selection of these hydrophobic materials based on their physico-chemical properties is important in designing wax matrix tablets with desired dissolution profile.

Silver nanoparticle release from commercially available plastic food containers into food simulants

NASA Astrophysics Data System (ADS)

Mackevica, Aiga; Olsson, Mikael Emil; Hansen, Steffen Foss

2016-01-01

Silver nanoparticles (AgNPs) are currently being used in many different kinds of consumer products in order to take advantage of their antimicrobial properties. However, the potential migration of silver nanoparticles into food and subsequent consumer exposure has hardly been addressed. In the current study, we investigated four brands of commercially available plastic food storage containers and measured the total amount of silver, particle size and number concentration, and the migration rates into three different food simulants (Milli-Q grade water, 10 % ethanol, and 3 % acetic acid) for 10 days at 40 °C. The experimental setup was made according to the European Commission Directive (EU 10/2011) for articles intended to be in contact with food. The total amount of silver in plastic containers and migration solutions was quantified by ICP-MS analysis, and the size of the migrated particles was investigated by single particle ICP-MS and TEM-EDS. The total mass and median size of released particulate Ag were generally highest in 3 % acetic acid for three out of four food container brands. The total content of silver in the containers varied from 13 to 42 µg/g. The highest migration was observed in the 3 % acetic acid food simulant for all four brands of containers, with total silver release up to 3.1 ng/cm2 after 10 days. In conclusion, the experimental results show that silver has the potential of migrating into food, especially when in contact with more acidic substances.

Atmospheric modeling of Mars CH4 subsurface clathrates releases mimicking SAM and 2003 Earth-based detections

NASA Astrophysics Data System (ADS)

Pla-Garcia, Jorge

2017-10-01

The aim of this work is to establish the amount of mixing during all martian seasons to test whether CH4 releases inside or outside of Gale crater are consistent with MSL-SAM observations. Several modeling scenarios were configured, including instantaneous and steady releases, both inside and outside the crater. A simulation to mimic the 2003 Earth-based detections (Mumma et al. 2009 or M09) was also performed. In the instantaneous release inside Gale experiments, Ls270 was shown to be the faster mixing season when air within and outside the crater was well mixed: all tracer mass inside the crater is diluted after just 8 hours. The mixing of near surface crater air with the external environment in the rest of the year is potentially rapid but slower than Ls270. In the instantaneous release outside Gale (NW) experiment, in just 12 hours the CH4 that makes it to the MSL landing location is diluted by six orders of magnitude. The timescale of mixing in the model is on the order of 1 sol regardless of season. The duration of the CH4 peak observed by SAM is 100 sols. Therefore there is a steady release inside the crater, or there is a large magnitude steady release outside the crater. In the steady release Gale experiments, CH4 flux rate from ground is 1.8 kg m-2 s-1 (Gloesener et al. 2017) and it is not predictive. In these experiments, ~200 times lower CH4 values detected by SAM are modeled around MSL location. There are CH4 concentration variations of orders of magnitude depending on the hour, so timing of SAM measurements is important. With a larger (but further away) outside crater release area compared to inside, similar CH4 values around MSL are modeled, so distance to source is important. In the steady experiments mimicking M09 detection release area, only 12 times lower CH4 values detected by SAM are modeled around MSL. The highest value in the M09 modeled scenario (0.6 ppbv) is reached in Ls270. This value is the highest of all modeled experiments. With our initial conditions, SAM should not be able to detect CH4, but if we multiply flux by 12, increase the release area or move it closer to MSL (or all of above), it may be possible to get CH4 values that SAM could detect regardless where it comes from.

Chitosan-functionalised poly(2-hydroxyethyl methacrylate) core-shell microgels as drug delivery carriers: salicylic acid loading and release.

PubMed

Mahattanadul, Natshisa; Sunintaboon, Panya; Sirithip, Piyawan; Tuchinda, Patoomratana

2016-09-01

This work presents the evaluation of chitosan-functionalised poly(2-hydroxyethyl methacrylate) (CS/PHEMA) core-shell microgels as drug delivery carriers. CS/PHEMA microgels were prepared by emulsifier-free emulsion polymerisation with N,N '-methylenebisacrylamide (MBA) as a crosslinker. The study on drug loading, using salicylic acid (SA) as a model drug, was performed. The results showed that the encapsulation efficiency (EE) increased as drug-to-microgel ratio was increased. Higher EE can be achieved with the increase in degree of crosslinking, by increasing the amount of MBA from 0.01 g to 0.03 g. In addition, the highest EE (61.1%) was observed at pH 3. The highest release of SA (60%) was noticed at pH 2.4, while the lowest one (49.4%) was obtained at pH 7.4. Moreover, the highest release of SA was enhanced by the presence of 0.2 M NaCl. The pH- and ionic-sensitivity of CS/PHEMA could be useful as a sustained release delivery device, especially for oral delivery.

The effect of rearing methods on survival of reintroduced black-footed ferrets

USGS Publications Warehouse

Biggins, D.E.; Godbey, J.L.; Hanebury, L.R.; Luce, B.; Marinari, P.E.; Matchett, M.R.; Vargas, A.

1998-01-01

We estimated minimum survival rates for 282 young-of-year, captive-reared, black-footed ferrets (Mustela nigripes) reintroduced into prairie dog (Cynomys spp.) colonies in Wyoming, Montana, and South Dakota. We used night surveys with spotlights to locate ferrets about 1 month and 9 months postrelease. We modeled minimum survival rates using gender, year, site, and 4 rearing methods. Minimum survival rates were highest (30% for 1 month, 20% for 9 months) for ferrets reared from early ages in outdoor pens with simulated prairie dog habitat; survival was lowest for cage-reared ferrets released without pen experience (11% for 1 month, 2% for 9 months). Rearing method and year influenced 1-month survival in a comparison of 3 levels of pen experience (pen rearing as defined above, transfer of kits from zoos to pen facilities at age 60-90 days, transfer at age >90 days) during releases in 1994-95 in Montana. Higher survival was associated with intensive management of coyotes (Canis latrans) in 1995. Survival was not different (P > 0.05) between sites or sexes, regardless of model. We recommend routine use of outdoor pens for prerelease conditioning of black-footed ferret kits.

Environmental risks of radioactive discharges from a low-level radioactive waste disposal site at Dessel, Belgium.

PubMed

Batlle, J Vives I; Sweeck, L; Wannijn, J; Vandenhove, H

2016-10-01

The potential radiological impact of releases from a low-level radioactive waste (Category A waste) repository in Dessel, Belgium on the local fauna and flora was assessed under a reference scenario for gradual leaching. The potential impact situations for terrestrial and aquatic fauna and flora considered in this study were soil contamination due to irrigation with contaminated groundwater from a well at 70 m from the repository, contamination of the local wetlands receiving the highest radionuclide flux after migration through the aquifer and contamination of the local river receiving the highest radionuclide flux after migration through the aquifer. In addition, an exploratory study was carried out for biota residing in the groundwater. All impact assessments were performed using the Environmental Risk from Ionising Contaminants: Assessment and Management (ERICA) tool. For all scenarios considered, absorbed dose rates to biota were found to be well below the ERICA 10 μGy h -1 screening value. The highest dose rates were observed for the scenario where soil was irrigated with groundwater from the vicinity of the repository. For biota residing in the groundwater well, a few dose rates were slightly above the screening level but significantly below the dose rates at which the smallest effects are observed for those relevant species or groups of species. Given the conservative nature of the assessment, it can be concluded that manmade radionuclides deposited into the environment by the near surface disposal of category A waste at Dessel do not have a significant radiological impact to wildlife. Copyright © 2016 Elsevier Ltd. All rights reserved.

A Comparative Evaluation of the Amount of Fluoride Release and Re-Release after Recharging from Aesthetic Restorative Materials: An in vitro Study.

PubMed

Bansal, Ruchika; Bansal, Tajinder

2015-08-01

To measure the amount of fluoride released and re released after recharging from various restorative materials: Conventional Glass Ionomer Cement (Fuji II), Light Cure Resin Modified GIC (Fuji II LC), Giomer (Beautifil II), Compomer (Dyract). Fifteen cylindrical specimens were prepared from each material. The specimens were immersed in 20 ml of deionized water. The amount of released fluoride was measured during the 1(st) day, 7(th) day and on the day15 by using specific fluoride electrode and an ion-analyser. After 15 days each material was divided into three Sub Groups of five samples each. Sub Group A served as control, Sub Group B was exposed to 2% NaF solution, Sub Group C to 1000ppm F toothpaste. The amount of fluoride re-released was measured during the 1(st) day, 7(th) day and on the day15 by using specific fluoride electrode and an ion-analyser. The results were statistically analysed using analysis of variance (one-way ANOVA) and Tukey Kramer multiple comparison tests (p≤0.05). Independent of the observation time period of the study the Conventional GIC released the highest amount of fluoride followed by RMGIC, Giomer and Compomer. The initial burst effect was seen with GIC'S but not with Giomer and Compomer. After topical fluoride application fluoride re release was highest in Sub Group B and GIC had a greater recharging ability followed by RMGIC, Giomer and Compomer. The fluoride re release was greatest on 1(st) day followed by rapid return to near exposure levels. From the study it was concluded that, the initial Fluoride release was highest from Conventional GIC followed by Resin Modified GIC, Giomer and Compomer. The Fluoride re release was high when recharging with professional regime (2% NaF) as compared to home regime (Toothpaste). Conventional GIC had a greater recharging ability followed by Resin Modified GIC, Giomer and Compomer.

Ion release and cytotoxicity of stainless steel wires.

PubMed

Oh, Keun-Taek; Kim, Kyoung-Nam

2005-12-01

Heat treatment is generally applied to orthodontic stainless steel (SS) wires to relieve the stresses that result from their manipulation by orthodontists. The quality and thickness of the oxide films formed on the surface of heat-treated wires can vary, and it is believed that these oxide films can influence the properties of heat-treated wires. The aim of this study was to investigate the influence of heat treatment and cooling methods on the amount of metal ions released and to examine the cytotoxicity of heat-treated wires. In this study, four types of SS wires (Remanium, Permachrome, Colboloy and Orthos) with a cross-sectional area of 0.41 x 0.56 mm were investigated. These wires were heat-treated in a vacuum, air, or argon environment, and were cooled in either a furnace or a water bath. Four control groups and 24 experimental groups were classified according to the type of wires, heat treatment conditions and cooling methods. In each group, the amount of nickel released as well as its cytotoxicity was investigated. The concentration of dissolved nickel ions in artificial saliva was measured for a period of up to 12 weeks. In all groups, the concentration of dissolved nickel ions in artificial saliva was lowest for the vacuum heat treatment-furnace cooling group and a significant difference was shown compared with the other experimental groups. The concentration of dissolved nickel ions in artificial saliva was highest in the groups heat-treated in air (P < 0.05), while the amount of nickel released was highest in the Remanium and Colboloy (P < 0.05). The cytotoxicity was mild in all the experimental groups but the response index of the air groups was slightly higher than in the other groups. According to these results, SS wires retain their high corrosion resistance and low ion release rate when heat-treated in a vacuum and cooled in a furnace.

Formulation and in vitro characterization of protein-loaded liposomes

NASA Astrophysics Data System (ADS)

Kuzimski, Lauren

Background/Objective: Protein-based drugs are increasingly used to treat a variety of conditions including cancer and cardio-vascular disease. Due to the immune system's innate ability to degrade the foreign particles quickly, protein-based treatments are generally short-lived. To address this limitation, the objective of the study was to: 1) develop protein-loaded liposomes; 2) characterize size, stability, encapsulation efficiency and rate of protein release; and 3) determine intracellular uptake and distribution; and 4) protein structural changes. Method: Liposomes were loaded with a fluorescent-albumin using freeze-thaw (F/T) methodology. Albumin encapsulation and release were quantified by fluorescence spectroscopic techniques. Flow cytometry was used to determine liposome uptake by macrophages. Epifluorescence microscopy was used to determine cellular distribution of liposomes. Stability was determined using dynamic light scattering by measuring liposome size over one month period. Protein structure was determined using circular dichroism (CD). Result: Encapsulation of albumin in liposome was ˜90% and was dependent on F/T rates, with fifteen cycles yielding the highest encapsulation efficacy (p < 0.05). Albumin-loaded liposomes demonstrated consistent size (<300nm). Release of encapsulated albumin in physiological buffer at 25°C was ˜60% in 72 h. Fluorescence imaging suggested an endosomal route of cellular entry for the FITC-albumin liposome with maximum uptake rates in immune cells (30% at 2hour incubation). CD suggested protein structure is minimally impacted by freeze-thaw methodology. Conclusion: Using F/T as a loading method, we were able to successfully achieve a protein-loaded liposome that was under 300nm, had encapsulation of ˜90%. Synthesized liposomes demonstrated a burst release of encapsulate protein (60%) at 72 hours. Cellular trafficking confirmed endosomal uptake, and minimal protein damage was noticed in CD.

pH and calcium ion release evaluation of pure and calcium hydroxide-containing Epiphany for use in retrograde filling

PubMed Central

TANOMARU-FILHO, Mário; SAÇAKI, Juliana Nogueira; FALEIROS, Frederico Bordini Chaves; GUERREIRO-TANOMARU, Juliane Maria

2011-01-01

Objective Hydroxyl (OH-) and calcium (Ca++) ion release was evaluated in six materials: G1) Sealer 26, G2) White mineral trioxide aggregate (MTA), G3) epiphany, G4) epiphany + 10% calcium hydroxide (CH), G5) epiphany + 20% CH, and G6) zinc oxide and eugenol. Material and Methods Specimens were placed in polyethylene tubes and immersed in distilled water. After 3, 6, 12, 24, and 48 h, 7, 14, and 28 days, the water was assessed for pH with a pH meter and for Ca++ release by atomic absorption spectrophotometry. Results G1, G2, G4, and G5 had the highest pH until 14 days (p<0.05). G1 presented the highest Ca++ release until 6 h, and G4 and G5, from 12 h through 14 days. Ca++ release was greater for G1 and G2 at 28 days. G6 released the least Ca++. Conclusion MTA, Sealer 26, epiphany, and epiphany + CH release OH - and Ca++ ions. Epiphany + CH may be an alternative as retrofilling material. PMID:21437461

Nitrogen release from rock and soil under simulated field conditions

USGS Publications Warehouse

Holloway, J.M.; Dahlgren, R.A.; Casey, W.H.

2001-01-01

A laboratory study was performed to simulate field weathering and nitrogen release from bedrock in a setting where geologic nitrogen has been suspected to be a large local source of nitrate. Two rock types containing nitrogen, slate (1370 mg N kg-1) and greenstone (480 mg N kg-1), were used along with saprolite and BC horizon sand from soils derived from these rock types. The fresh rock and weathered material were used in batch reactors that were leached every 30 days over 6 months to simulate a single wet season. Nitrogen was released from rock and soil materials at rates between 10-20 and 10-19 mo1 N cm-2 s-1. Results from the laboratory dissolution experiments were compared to in situ soil solutions and available mineral nitrogen pools from the BC horizon of both soils. Concentrations of mineral nitrogen (NO3- + NH4+) in soil solutions reached the highest levels at the beginning of the rainy season and progressively decreased with increased leaching. This seasonal pattern was repeated for the available mineral nitrogen pool that was extracted using a KCl solution. Estimates based on these laboratory release rates bracket stream water NO3-N fluxes and changes in the available mineral nitrogen pool over the active leaching period. These results confirm that geologic nitrogen, when present, may be a large and reactive pool that may contribute as a non-point source of nitrate contamination to surface and ground waters. ?? 2001 Elsevier Science B.V. All rights reserved.

Release of metals from metal-amended soil treated with a sulfosuccinamate surfactant: effects of surfactant concentration, soil/solution ratio, and pH.

PubMed

Hernández-Soriano, Maria del Carmen; Peña, Aránzazu; Dolores Mingorance, Ma

2010-01-01

Anionic surfactants, mainly sulfosuccinamates, can be found in soils as the result of sludge application, wastewater irrigation, and remediation processes. Relatively high concentrations of surfactants together with multimetals can represent an environmental risk. A study was performed to assess the potential of the anionic surfactant Aerosol 22 (A22) for release of Cd, Cu, Pb, and Zn from a metal-amended soil representative of a Mediterranean area. Metal desorption was performed by batch experiments and release kinetics were assessed. Response surface methodology was applied to determine the influence of A22 concentration and the surfactant/soil ratio, as extraction key factors. An increase in solution/soil ratio to 100 (mL g(-1)) caused higher metal release. Leaching predictions found Pb to have the lowest and Cd the highest hazard. Metal release was highly dependent on pH. When extraction was made at pH less than 7, low or negligible amounts of metals were leached, whereas an increase to pH 7 caused desorption rates of 50 to 55% for Cd, Cu, and Zn but only 35% for Pb. Complexed metal-carboxylic groups from A22 were mainly responsible for its higher extractive capacity, especially of Cd and Cu.

Development of Long-Circulating pH-Sensitive Liposomes to Circumvent Gemcitabine Resistance in Pancreatic Cancer Cells.

PubMed

Xu, Hongtao; Paxton, James W; Wu, Zimei

2016-07-01

To develop pH-sensitive liposomes (PSL) containing a high content of gemcitabine; and to investigate whether drug loading (DL) would alter the in vitro and pharmacokinetic properties. PSL with a high DL were obtained using a modified small-volume incubation method. The DL effects on drug release rate and in vitro cytotoxicity of PSL were evaluated using MIA PaCa-2 pancreatic cancer cells and their pharmacokinetics investigated in rats. The highest DL of 4.5 ± 0.1% was achieved for gemcitabine in PSL with 145 ± 5 nm diameter. DL did not alter the in vitro release rate from PSL. The IC50 (48 h) of PSL (DL 0.5 and 4.5%) and non pH-sensitive liposomes (NPSL, DL 4.2%) were 1.1 ± 0.1, 0.7 ± 0.1 and 37.0 ± 7.5 μM, respectively. The PSL resulted in a 4.2-fold increase in its elimination half-life (6.2 h) compared to gemcitabine solution (1.4 h) in rats. No significant difference in pharmacokinetic parameters was observed between the two PSL (DL 0.5 and 4.5%). The PSL offered advantages over NPSL in restoring the sensitivity of pancreatic cancer cells to gemcitabine without requiring a high DL. DL in the PSL did not alter release rate, cytotoxicity or their long-circulating properties. Graphical Abstract ᅟ.

High birth rates despite easy access to contraception and abortion: a cross-sectional study.

PubMed

Hognert, Helena; Skjeldestad, Finn E; Gemzell-Danielsson, Kristina; Heikinheimo, Oskari; Milsom, Ian; Lidegaard, Øjvind; Lindh, Ingela

2017-12-01

The aim of this study was to describe and compare contraceptive use, fertility, birth, and abortion rates in the Nordic countries. National data on births, abortions, fertility rate (1975-2013), redeemed prescriptions of hormonal contraceptives and sales figures of copper intrauterine devices (2008-2013) among women 15-49 years of age in the Nordic countries were collected and analyzed. Use of hormonal contraceptives and copper intrauterine devices varied between 31 and 44%. The highest use was in Denmark (39-44%) and Sweden (40-42%). Combined hormonal contraception followed by the levonorgestrel-releasing intrauterine system were the most common methods. During 1975-2013 abortion rates decreased in Denmark (from 27/1000 women to 15/1000 women aged 15-44/1000 women) and Finland (from 20 to 10/1000 women), remained stable in Norway (≈16) and Sweden (≈20) and increased in Iceland (from 6 to 15/1000 women). Birth rates remained stable around 60/1000 women aged 15-44 in all countries except for Iceland where the birth rate decreased from 95 to 65/1000 women. Abortion rates were highest in the age group 20-24 years. In the same age group, Sweden had a lower contraceptive use (51%) compared with Denmark (59%) and Norway (56%) and a higher abortion rate 33/1000 compared with Denmark (25/1000) and Norway (27/1000). In contrast to the declining average fertility and birth rates in Europe, rates in the Nordic countries remain high and stable despite high contraceptive use and liberal access to abortion on women's request. © 2017 Nordic Federation of Societies of Obstetrics and Gynecology.

Development of an Extended-Release Formulation for Apremilast and a Level A in Vitro-in Vivo Correlation Study in Beagle Dogs.

PubMed

Tang, Meiqiong; Hu, Ping; Huang, Shigui; Zheng, Qiang; Yu, Hao; He, Yun

2016-11-01

The primary objective of the present study was to develop extended-release matrix formulations of apremilast for the oral delivery and to study their in vitro and in vivo correlation. Five extended-release formulations containing hydroxypropylmethylcellulose (HPMC) as the retarding excipient with different release rate of apremilast were prepared. Dissolution tests of all the formulated tablets were performed in water, pH 4.0 and 6.8 buffer solutions. The in vitro release kinetics was studied and supported by Korsmeyer-Peppas's equation as it presented highest values of correlation coefficients (r 2 up to 0.966). Among all formulated tablets, F2 (HPMC 25%) and F4 (HPMC 35%) were selected to perform an in vivo study in beagle dogs to obtain various pharmacokinetic parameters, i.e., peak plasma concentration (C max ), time to peak plasma concentration (t max ), area under the plasma-concentration vs. time curve (AUC). Higher t max and t 1/2 , lower C max and elimination coefficient (K e ) were observed for both extended formulations compared to marketed immediate-release products (Otezla ® ). Level A in vitro-in vivo correlations were created with the help of Wagner-Nelson and numeric deconvolution methods. Both formulations showed good in vitro-in vivo correlations whose accuracies were further verified by an internal validation.

Determination of etching parameters for pulsed XeF2 etching of silicon using chamber pressure data

NASA Astrophysics Data System (ADS)

Sarkar, Dipta; Baboly, M. G.; Elahi, M. M.; Abbas, K.; Butner, J.; Piñon, D.; Ward, T. L.; Hieber, Tyler; Schuberth, Austin; Leseman, Z. C.

2018-04-01

A technique is presented for determination of the depletion of the etchant, etched depth, and instantaneous etch rate for Si etching with XeF2 in a pulsed etching system in real time. The only experimental data required is the pressure data collected temporally. Coupling the pressure data with the knowledge of the chemical reactions allows for the determination of the etching parameters of interest. Using this technique, it is revealed that pulsed etching processes are nonlinear, with the initial etch rate being the highest and monotonically decreasing as the etchant is depleted. With the pulsed etching system introduced in this paper, the highest instantaneous etch rate of silicon was recorded to be 19.5 µm min-1 for an initial pressure of 1.2 Torr for XeF2. Additionally, the same data is used to determine the rate constant for the reaction of XeF2 with Si; the reaction is determined to be second order in nature. The effect of varying the exposed surface area of Si as well as the effect that pressure has on the instantaneous etch rate as a function of time is shown applying the same technique. As a proof of concept, an AlN resonator is released using XeF2 pulses to remove a sacrificial poly-Si layer.

A novel system to diagnose cutaneous adverse drug reactions employing the cellscan--comparison with histamine releasing test and Inf-gamma Releasing Test.

PubMed

Goldberg, Ilan; Gilburd, Boris; Kravitz, Martine Szyper; Kivity, Shmuel; Chaim, Berta Ben; Klein, Tirza; Schiffenbauer, Yael; Trubniykovr, Ela; Brenner, Sarah; Shoenfeld, Yehuda

2005-03-01

There are several mechanisms to describe allergic drug reactions yet the methods to diagnose them are limited. To compare several conventional clinical and laboratory methods to diagnose skin reactions to drugs to a new method of diagnosing drug reactions by the CellScan system. The study entailed 21 patients who were diagnosed as suffering from drug eruptions, and 105 healthy controls with no history of drug allergy. The drugs were classified into two groups according to suspicion of causing drug allergy: high and low. Most of the patients were on more than one drug, leading to 41 patient-drug interactions (assays). Histamine releasing test (HRT), interferon (INF)-gamma releasing test and CellScan examination were performed on lymphocytes of the patients and controls. The HRTwas interpreted as positive in 9 out of 18 (50%) patients and in 13 out of 35 (37%) assays. Based on the INF-gamma releasing test, positive results were observed in 16 out of 21 (76%) patients and in 24 out of 41 (59%) assays. In the CellScan test (CST), positive results were observed in 17 out of 21 (81%) patients and in 29 out of 41 (71%) assays. The rate of identifying the drug for eruption in the high suspicion level drugs was 9 out of 22 (41%) assays in the HRT, 20 out of 24 (83%) assays in the INF-gamma releasing test, and 21 out of 24 (87%) studies with the CellScan method. The rate of determining of the drug that caused the eruption in the low suspicion level drugs was 4 out of 13 (31 %) in the HRT, 4 out of 17 (24%) assays in the INF-gamma releasing test, and 8 out of 17 (47%) analyses in the CST. When examined in the CellScan, 99 out of 105 (94%) controls were interpreted as negative. This preliminary study indicates that the CellScan seems to be an easy and promising method for the detection of drugs responsible for adverse skin reactions. In contrast to the HRT and to the Interferon-gamma secretion test, the CellScan method is characterized by its ability to track and monitor the reaction of individual cells. By measuring the kinetic parameters of selected cells before and after adding the suspected drug, we were able to identify the culprit drug. The CellScan method had the highest sensitivity, and the interferon-gamma secretion test had the highest specificity for detection of the culprit drug. In contrast, the analysis of 105 normal control sera disclosed a high specificity of 94% for the CellScan method.

Effects of Coral Reef Benthic Primary Producers on Dissolved Organic Carbon and Microbial Activity

PubMed Central

Haas, Andreas F.; Nelson, Craig E.; Wegley Kelly, Linda; Carlson, Craig A.; Rohwer, Forest; Leichter, James J.; Wyatt, Alex; Smith, Jennifer E.

2011-01-01

Benthic primary producers in marine ecosystems may significantly alter biogeochemical cycling and microbial processes in their surrounding environment. To examine these interactions, we studied dissolved organic matter release by dominant benthic taxa and subsequent microbial remineralization in the lagoonal reefs of Moorea, French Polynesia. Rates of photosynthesis, respiration, and dissolved organic carbon (DOC) release were assessed for several common benthic reef organisms from the backreef habitat. We assessed microbial community response to dissolved exudates of each benthic producer by measuring bacterioplankton growth, respiration, and DOC drawdown in two-day dark dilution culture incubations. Experiments were conducted for six benthic producers: three species of macroalgae (each representing a different algal phylum: Turbinaria ornata – Ochrophyta; Amansia rhodantha – Rhodophyta; Halimeda opuntia – Chlorophyta), a mixed assemblage of turf algae, a species of crustose coralline algae (Hydrolithon reinboldii) and a dominant hermatypic coral (Porites lobata). Our results show that all five types of algae, but not the coral, exuded significant amounts of labile DOC into their surrounding environment. In general, primary producers with the highest rates of photosynthesis released the most DOC and yielded the greatest bacterioplankton growth; turf algae produced nearly twice as much DOC per unit surface area than the other benthic producers (14.0±2.8 µmol h−1 dm−2), stimulating rapid bacterioplankton growth (0.044±0.002 log10 cells h−1) and concomitant oxygen drawdown (0.16±0.05 µmol L−1 h−1 dm−2). Our results demonstrate that benthic reef algae can release a significant fraction of their photosynthetically-fixed carbon as DOC, these release rates vary by species, and this DOC is available to and consumed by reef associated microbes. These data provide compelling evidence that benthic primary producers differentially influence reef microbial dynamics and biogeochemical parameters (i.e., DOC and oxygen availability, bacterial abundance and metabolism) in coral reef communities. PMID:22125645

Changes in CO2 diffuse degassing induced by the passing of seismic waves

NASA Astrophysics Data System (ADS)

Gresse, M.; Vandemeulebrouck, J.; Byrdina, S.; Chiodini, G.; Bruno, P. P.

2016-06-01

Solfatara crater, located in the Campi Flegrei caldera, is a volcano with one of the highest degassing rates on Earth, more than 1500 t of CO2 released by diffusion or through vents. Here, we investigated how this gas release can be disrupted by the passage of seismic waves. We performed continuous soil CO2 flux measurements during the propagation of seismic vibrations in the range of 5 Hz to 200 Hz induced by a vibroseis truck. The CO2 flux was continuously recorded using the accumulation chamber method. The data show a temporary and drastic (up to two-fold) increase in CO2 flux exclusively during the vibrations, before returning to the initial flux values. These transient variations are interpreted as fluidization of the surficial granular layer that releases the stored gas. Similar degassing processes might occur at a larger scale during earthquakes, to cause temporary increases in the total gas outflow in volcanic or tectonic areas. Our findings are useful to better assess and monitor the potential hazard from sudden CO2 flux release during earthquakes as several cases of intoxication or death have already been related to volcanic degassing.

Ultrasound stimulated release of gallic acid from chitin hydrogel matrix.

PubMed

Jiang, Huixin; Kobayashi, Takaomi

2017-06-01

Ultrasound (US) stimulated drug release was examined in this study using a chitin hydrogel matrix loaded with gallic acid (GA), a drug used for wound healing and anticancer. Using phase inversion, GA-chitin hydrogels were prepared from chitin-dimethylacetamide (DMAc)/lithium chloride (LiCl) solution in the presence of GA, with 24h exposure of the solution to water vapor. The GA release from the GA-chitin hydrogel was examined under different US powers of 0-30W at 43kHz. The effects of GA loading amounts in the hydrogels (0.54, 0.43, and 0.25mg/cm 3 ) and chitin concentrations (0.1, 0.5, and 1wt%) on the release behaviors were recorded under 43kHz US exposure at 30W. Results show that US accelerated the release efficiencies for all samples. Furthermore, the release efficiency increased concomitantly with increasing US power, GA loading amount, and decrease of the chitin concentration. The highest release rate of 0.74μg/mL·min was obtained from 0.54mg/cm 3 of GA-loaded hydrogel fabricated from a 0.1wt% chitin mixture solution under 43kHz US exposure at 30W: nine times higher than that of the sample without US exposure. The hydrogel viscoelasticity demonstrated that the US irradiation rigidified the material. FT-IR showed that US can break the hydrogen bonds in the GA-chitin hydrogels. Copyright © 2017 Elsevier B.V. All rights reserved.

Rapid mineralisation of the Organic Fraction of Municipal Solid Waste.

PubMed

Martínez-Valdez, F J; Martínez-Ramírez, C; Martínez-Montiel, L; Favela-Torres, E; Soto-Cruz, N O; Ramírez-Vives, F; Saucedo-Castañeda, G

2015-03-01

The effect of pH, C/N ratio, addition of a microbial consortium (MC) and temperature upon mineralisation of Organic Fraction of Municipal Solid Waste (OFMSW) was studied; mineralisation was measured through the CO2 production rate and total CO2 formation. Through this process up to 432.9mg of CO2g(-1) initial dry matter (IDM) after 2days of treatment was obtained. It was found that under a slightly acidic pH (5-6) and C/N of 30, the mineralisation process was accelerated. Moreover, temperature (27-50°C) had no effect on the total CO2 produced. The highest CO2 production rate (5.28d(-1)) was observed at 27°C, C/N ratio of 30 and 8% of microbial consortium; it is at least 3.52 times higher than that reported (1.5d(-1)). The highest release of reducing sugars was determined at 50°C, possibly due to an increase in hydrolytic enzymes. Results suggest the potential use of rapid mineralisation of OFMSW for further friendly environmental processes. Copyright © 2014 Elsevier Ltd. All rights reserved.

Steam explosion distinctively enhances biomass enzymatic saccharification of cotton stalks by largely reducing cellulose polymerization degree in G. barbadense and G. hirsutum.

PubMed

Huang, Yu; Wei, Xiaoyang; Zhou, Shiguang; Liu, Mingyong; Tu, Yuanyuan; Li, Ao; Chen, Peng; Wang, Yanting; Zhang, Xuewen; Tai, Hongzhong; Peng, Liangcai; Xia, Tao

2015-04-01

In this study, steam explosion pretreatment was performed in cotton stalks, leading to 5-6 folds enhancements on biomass enzymatic saccharification distinctive in Gossypium barbadense and Gossypium hirsutum species. Sequential 1% H2SO4 pretreatment could further increase biomass digestibility of the steam-exploded stalks, and also cause the highest sugar-ethanol conversion rates probably by releasing less inhibitor to yeast fermentation. By comparison, extremely high concentration alkali (16% NaOH) pretreatment with raw stalks resulted in the highest hexoses yields, but it had the lowest sugar-ethanol conversion rates. Characterization of wall polymer features indicated that biomass saccharification was enhanced with steam explosion by largely reducing cellulose DP and extracting hemicelluloses. It also showed that cellulose crystallinity and arabinose substitution degree of xylans were the major factors on biomass digestibility in cotton stalks. Hence, this study has provided the insights into cell wall modification and biomass process technology in cotton stalks and beyond. Copyright © 2015 Elsevier Ltd. All rights reserved.

Fluoride-containing nanoporous calcium-silicate MTA cements for endodontics and oral surgery: early fluorapatite formation in a phosphate-containing solution.

PubMed

Gandolfi, M G; Taddei, P; Siboni, F; Modena, E; Ginebra, M P; Prati, C

2011-10-01

To test the chemical-physical properties and apatite-forming ability of experimental fluoride-doped calcium silicate cements designed to create novel bioactive materials for use in endodontics and oral surgery. A thermally treated calcium silicate cement (wTC) containing CaCl(2) 5%wt was modified by adding NaF 1%wt (FTC) or 10%wt (F10TC). Cements were analysed by environmental scanning electron microscopy with energy-dispersive X-ray analysis, IR and micro-Raman spectroscopy in wet conditions immediately after preparation or after ageing in a phosphate-containing solution (Dulbecco's phosphate-buffered saline). Calcium and fluoride release and pH of the storage solution were measured. The results obtained were analysed statistically (Tukey's HSD test and two-way anova). The formation of calcium phosphate precipitates (spherulites) was observed on the surface of 24 h-aged cements and the formation of a thick bone-like B-type carbonated apatite layer (biocoating) on 28 day-aged cements. The rate of apatite formation was FTC>F10TC>wTC. Fluorapatite was detected on FTC and F10TC after 1 day of ageing, with a higher fluoride content on F10TC. All the cements released calcium ions. At 5 and 24 h, the wTC had the significantly highest calcium release (P<0.001) that decreased significantly over the storage time. At 3-28 days, FTC and F10TC had significantly higher calcium release than wTC (P<0.05). The F10TC had the significantly highest fluoride release at all times (P<0.01) that decreased significantly over storage time. No significant differences were observed between FTC and wTC. All the cements had a strong alkalinizing activity (OH(-) release) that remained after 28 days of storage. The addition of sodium fluoride accelerated apatite formation on calcium silicate cements. Fluoride-doped calcium silicate cements had higher bioactivity and earlier formation of fluorapatite. Sodium fluoride may be introduced in the formulation of mineral trioxide aggregate cements to enhance their biological behaviour. F-doped calcium silicate cements are promising bone cements for clinical endodontic use. © 2011 International Endodontic Journal.

Mortality of Siberian polecats and black-footed ferrets released onto prairie dog colonies

USGS Publications Warehouse

Biggins, D.E.; Miller, B.J.; Hanebury, L.R.; Powell, R.A.

2011-01-01

Black-footed ferrets (Mustela nigripes) likely were extirpated from the wild in 19851986, and their repatriation depends on captive breeding and reintroduction. Postrelease survival of animals can be affected by behavioral changes induced by captivity. We released neutered Siberian polecats (M. eversmanii), close relatives of ferrets, in 19891990 on black-tailed prairie dog (Cynomys ludovicianus) colonies in Colorado and Wyoming initially to test rearing and reintroduction techniques. Captive-born polecats were reared in cages or cages plus outdoor pens, released from elevated cages or into burrows, and supplementally fed or not fed. We also translocated wild-born polecats from China in 1990 and released captive-born, cage-reared black-footed ferrets in 1991, the 1st such reintroduction of black-footed ferrets. We documented mortality for 55 of 92 radiotagged animals in these studies, mostly due to predation (46 cases). Coyotes (Canis latrans) killed 31 ferrets and polecats. Supplementally fed polecats survived longer than nonprovisioned polecats. With a model based on deaths per distance moved, survival was highest for wild-born polecats, followed by pen-experienced, then cage-reared groups. Indexes of abundance (from spotlight surveys) for several predators were correlated with mortality rates of polecats and ferrets due to those predators. Released black-footed ferrets had lower survival rates than their ancestral population in Wyoming, and lower survival than wild-born and translocated polecats, emphasizing the influence of captivity. Captive-born polecats lost body mass more rapidly postrelease than did captive-born ferrets. Differences in hunting efficiency and prey selection provide further evidence that these polecats and ferrets are not ecological equivalents in the strict sense. ?? 2011 American Society of Mammalogists.

[Effects of selective cutting disturbance on soil phosphorus adsorption and desorption in a Korean pine and broad-leaved mixed forest in the Xiaoxing'an Mountains, China.

PubMed

Zhang, Xin; Gu, Hui Yan; Chen, Xiang Wei

2018-01-01

This study examined the characteristics of phosphorus (P) adsorption and desorption in surface soil (0-10 cm) of a secondary forest after selective cutting disturbance at three levels of intensity (low, medium, high) in order to reveal the effects of different disturbance intensities on soil P adsorption and desorption. Maximum adsorption amount (Q m ), adsorption intensity factor, maximum buffer capacity, maximum desorption amount, average desorption rate and readily desorptable phosphorus were measured. Q m in the focal forests was 1383.93-1833.34 mg·kg -1 , and Q m in forests with middle and high disturbance intensities was significantly higher than that in forests with low disturbance intensity and in primary forests. P adsorption intensity was 0.024-0.059 L·mg -1 , and forests with high and low disturbance intensities increased the P adsorption intensity significantly. The maximum buffer capacity varied from 35.68 to 97.97 L·kg -1 , with the highest value found in the forest with the highest disturbance intensity. Selective cutting significantly reduced the potential for phosphorus supply in the forest soils. The maximum desorption amount, average desorption rate and readily desorptable phosphorus content in the focal forests were 526.32-797.54 mg·kg -1 , 14.7%-25.5% and 1.79-5.41 mg·kg -1 , respectively, indicating that the ability of soil to release phosphorus significantly decreased with increasing disturbance intensity. Selective cutting changed the phosphorus adsorption and desorption characteristics by reducing the supply and release of soil phosphorus.

Effects of egg yolk, glycerol and the freezing rate on the viability and acrosomal structures of frozen ram spermatozoa.

PubMed

Watson, P F; Martin, I C

1975-04-01

The influence of egg yolk, glycerol and the freezing rate on the survival of ram spermatozoa and on the structure of their acrosomes after freezing was investigated. Egg yolk was shown to be beneficial not only during chilling but also during freezing; of the levels examined, 1-5% gave the greatest protection. Although the presence of glycerol in the diluent improved the survival of spermatozoa, increasing concentrations produced significant deterioration of the acrosomes. With closely controlled linear cooling rates, no overall difference was detected in the survival of spermatozoa frozen at rates between 6 and 24 degrees C per min. However, a significant interaction between freezing rate and the inclusion of glycerol in the diluent showed that glycerol was less important at the highest freezing rate. A sudden cooling phase near to the freezing point following the release of the latent heat of fusion was not detrimental to spermatozoa.

[Effects of fluridone, gibberellin acid and germination temperature on dormancy-breaking for Epimedium wushanense].

PubMed

Su, He; Wang, Yue; Yang, Yang; Dong, Xue-Hui

2016-07-01

We introduced Epimedium wushanense seed which has been stratified for 90 days at 10/20 ℃ as experimental materials, with which we studied the effects of fluridone, gibberellin acid and temperature on E. wushanense germination. The results were suggested as shown below. ①Temperature, fluridone and gibberellin acid can both solely or jointly affect germination energy, germination rate significantly. Among those factors, fluridone affect germination rate and germination energy the most, followed by gibberellin acid and temperature. The highest germination rate under 4 ℃ and 10/20 ℃ stratification are 79.3%, 72.0% respectively, which resulted from treatment of F10GA300 and F20GA200 respectively. The highest germination energy under 4 ℃ and 10/20 ℃ stratification are 52.7%, 52.0%, respectively, which both resulted from F20GA200. ②Compared with 4 ℃ germination, seed could not germinate at 10/20 ℃ germination. Nontheless, application of fluridone can lead E. wushanense seeds to germinating.③The effects of gibberellin acid and interaction between gibberellin acid and fluridone significantly affect seed rotten rate during germination. In addition, soaking is another remarkable factor which increased seed rotten rate. As a result, it is feasible to promote E. wushanense dormancy releasing with gibberellin acid and fluridone associating with a proper germination temperature. Further, it is necessary taking actions to avoid seed rotten rate for saving E. wushanense nurseries'cost. Copyright© by the Chinese Pharmaceutical Association.

A comparative study on the effects of amphiphilic and hydrophilic polymers on the release profiles of a poorly water-soluble drug.

PubMed

Irwan, Anastasia W; Berania, Jacqueline E; Liu, Xueming

2016-03-01

This paper reports the use of two crystalline polymers, an amphiphilic Pluronic® F-127 (PF-127) and a hydrophilic poly(ethylene glycol) (PEG6000) as drug delivery carriers for improving the drug release of a poorly water-soluble drug, fenofibrate (FEN), via micelle formation and formation of a solid dispersion (SD). In 10% PF-127 (aq.), FEN showed an equilibrium solubility of ca. 0.6 mg/mL, due to micelle formation. In contrast, in 10% PEG6000 (aq.), FEN only exhibited an equilibrium solubility of 0.0037 mg/mL. FEN-loaded micelles in PF-127 were prepared by direct dissolution and membrane dialysis. Both methods only yielded a highest drug loading (DL) of 0.5%. SDs of FEN in PF-127 and PEG6000, at DLs of 5-80%, were prepared by solvent evaporation. In-vitro dissolution testing showed that both micelles and SDs significantly improved FEN's release rate. The SDs of FEN in PF-127 showed significantly faster release than crystalline FEN, when the DL was as high as 50%, whereas SDs of PEG6000 showed similar enhancement in the release rate when the DL was not more than 20%. The DSC thermograms of SDs of PF-127 exhibited a single phase transition peak at ca. 55-57 °C when the DL was not more than 50%, whereas those in PEG6000 exhibited a similar peak at ca. 61-63 °C when the DL was not more than 35%. When the DL exceeded 50% for SDs of PF-127 and 35% for SDs of PEG6000, DSC thermograms showed two melting peaks for the carrier polymer and FEN, respectively. FT-IR studies revealed that PF-127 has a stronger hydrophobic-hydrophobic interaction with FEN than PEG6000. It is likely that both dispersion and micelle formation contributed to the stronger effect of PF-127 on enhancing the release rate of FEN in its SDs.

Effect of temperature and high pressure on the activity and mode of action of fungal pectin methyl esterase.

PubMed

Duvetter, Thomas; Fraeye, Ilse; Sila, Daniel N; Verlent, Isabel; Smout, Chantal; Clynen, Elke; Schoofs, Liliane; Schols, Henk; Hendrickx, Marc; Van Loey, Ann

2006-01-01

Pectin was de-esterified with purified recombinant Aspergillus aculeatus pectin methyl esterase (PME) during isothermal-isobaric treatments. By measuring the release of methanol as a function of treatment time, the rate of enzymatic pectin conversion was determined. Elevated temperature and pressure were found to stimulate PME activity. The highest rate of PME-catalyzed pectin de-esterification was obtained when combining pressures in the range 200-300 MPa with temperatures in the range 50-55 degrees C. The mode of pectin de-esterification was investigated by characterizing the pectin reaction products by enzymatic fingerprinting. No significant effect of increasing pressure (300 MPa) and/or temperature (50 degrees C) on the mode of pectin conversion was detected.

Processing Ti-25Ta-5Zr Bioalloy via Anodic Oxidation Procedure at High Voltage

NASA Astrophysics Data System (ADS)

Ionita, Daniela; Grecu, Mihaela; Dilea, Mirela; Cojocaru, Vasile Danut; Demetrescu, Ioana

2011-12-01

The current paper reports the processing of Ti-25Ta-5Zr bioalloy via anodic oxidation in NH4BF4 solution under constant potentiostatic conditions at high voltage to obtain more suitable properties for biomedical application. The maximum efficiency of the procedure is reached at highest applied voltage, when the corrosion rate in Hank's solution is decreased approxomately six times. The topography of the anodic layer has been studied using atomic force microscopy (AFM), and the results indicated that the anodic oxidation process increases the surface roughness. The AFM images indicated a different porosity for the anodized surfaces as well. After anodizing, the hydrophilic character of Ti-25Ta-5Zr samples has increased. A good correlation between corrosion rate obtained from potentiodynamic curves and corrosion rate from ions release analysis was obtained.

Delignification of disposable wooden chopsticks waste for fermentative hydrogen production by an enriched culture from a hot spring.

PubMed

Phummala, Kanthima; Imai, Tsuyoshi; Reungsang, Alissara; Chairattanamanokorn, Prapaipid; Sekine, Masahiko; Higuchi, Takaya; Yamamoto, Koichi; Kanno, Ariyo

2014-06-01

Hydrogen (H2) production from lignocellulosic materials may be enhanced by removing lignin and increasing the porosity of the material prior to enzymatic hydrolysis. Alkaline pretreatment conditions, used to delignify disposable wooden chopsticks (DWC) waste, were investigated. The effects of NaOH concentration, temperature and retention time were examined and it was found that retention time had no effect on lignin removal or carbohydrate released in enzymatic hydrolysate. The highest percentage of lignin removal (41%) was obtained with 2% NaOH at 100°C, correlated with the highest carbohydrate released (67 mg/g pretreated DWC) in the hydrolysate. An enriched culture from a hot spring was used as inoculum for fermentative H2 production, and its optimum initial pH and temperature were determined to be 7.0 and 50°C, respectively. Furthermore, enzymatic hydrolysate from pretreated DWC was successfully demonstrated as a substrate for fermentative H2 production by the enriched culture. The maximum H2 yield and production rate were achieved at 195 mL H2/g total sugars consumed and 116 mL H2/(L·day), respectively. Copyright © 2014 The Research Centre for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

Effect of temperature-driven phase transition on energy-storage and -release properties of Pb0.97La0.02[Zr0.55Sn0.30Ti0.15]O3 ceramics

NASA Astrophysics Data System (ADS)

Xu, Ran; Tian, Jingjing; Zhu, Qingshan; Feng, Yujun; Wei, Xiaoyong; Xu, Zhuo

2017-07-01

Temperature-driven phase transition of Pb0.97La0.02[Zr0.55Sn0.30Ti0.15]O3 ceramics was studied, and the consecutive ferroelectric-antiferroelectric-paraelectric (FE-AFE-PE) switching was confirmed. The materials have better dielectric tunability (-82% to 50%) in the AFE state than in the FE state. Also, the phase transition influences the energy-storage and -release performance significantly. A sharp increase in releasable energy density and efficiency was observed due to the temperature-driven FE-AFE transition. Highest releasable energy density, current density, and peak power density were achieved at 130 °C, which was attributed to the highest backward transition field. The stored charge was released completely in AFE and PE states in the microseconds scale, while only a small part of it was released in the FE state. The above results indicate the huge impact of temperature-driven phase transition on dielectrics' performance, which is significant when developing AFE materials working in a wide temperature range.

Perfluorocarbon Tracer Experiments on a 2 km Scale in Manchester Showing Ingress of Pollutants into a Building

NASA Astrophysics Data System (ADS)

Matthews, James; Wright, Matthew; Bacak, Asan; Silva, Hugo; Priestley, Michael; Martin, Damien; Percival, Carl; Shallcross, Dudley

2016-04-01

Cyclic perfluorocarbons (PFCs) have been used to measure the passage of air in urban and rural settings as they are chemically inert, non-toxic and have low background concentrations. The use of pre-concentrators and chemical ionisation gas chromatography enables concentrations of a few parts per quadrillion (ppq) to be measured in bag samples. Three PFC tracers were used in Manchester, UK in the summer of 2015 to map airflow in the city and ingress into buildings: perfluomethylcyclohexane (PMCH), perfluoro-2-4-dimethylcyclohexane (mPDMCH) and perfluoro-2-methyl-3-ethylpentene (PMEP). A known quantity of each PFC was released for 15 minutes from steel canisters using pre-prepared PFC mixtures. Release points were chosen to be upwind of the central sampling location (Simon Building, University of Manchester) and varied in distance up to 2.2 km. Six releases using one or three tracers in different configurations and under different conditions were undertaken in the summer. Three further experiments were conducted in the Autumn, to more closely investigate the rate of ingress and decay of tracer indoors. In each experiment, 10 litre samples were made over 30 minutes into Tedlar bags, starting at the same time the as PFC release. Samples were taken in 11 locations chosen from 15 identified areas including three in public parks, three outside within the University of Manchester area, seven inside and five outside of the Simon building and two outside a building nearby. For building measurements, receptors were placed inside the buildings on different floors; outside measurements were achieved through a sample line out of the window. Three of the sample positions inside the Simon building were paired with samplers outside to allow indoor-outdoor comparisons. PFC concentrations varied depending on location and height. The highest measured concentrations occurred when the tracer was released at sunrise; up to 330 ppq above background (11 ppq) of PMCH was measured at the 6th floor of the Simon Building from a release 1.9 km away. One experiment sampled for an additional two 30 minute periods in four locations inside and one location outside the Simon Building in order to investigate how long it took for air to enter and leave the building. For this measurement, 1.3 g of PMCH was released 1.9 km away and average roof level wind speed was 7.8 m/s. The highest measurement of PMCH outside was 54 ppq above background, and 46 ppq inside. After the first 30 minutes, the PFC concentration returned to background levels outside, but other internal rooms still had elevated PFC concentrations between 10 and 16 ppq above background an hour after release demonstrating that pollutants may persist within buildings having passed outside. In the final experiment, the wind direction changed so the sampling locations were not directly downwind of the release point, but nevertheless a small amount of PFC tracer above background was detected at the highest sampling point on the 6th floor of the Simon Building (14 ppq above background), and a smaller amount at street level.

Enhanced biological phosphorus removal in a sequencing batch reactor using propionate as the sole carbon source.

PubMed

Pijuan, M; Saunders, A M; Guisasola, A; Baeza, J A; Casas, C; Blackall, L L

2004-01-05

An enhanced biological phosphorus removal (EBPR) system was developed in a sequencing batch reactor (SBR) using propionate as the sole carbon source. The microbial community was followed using fluorescence in situ hybridization (FISH) techniques and Candidatus 'Accumulibacter phosphatis' were quantified from the start up of the reactor until steady state. A series of SBR cycle studies was performed when 55% of the SBR biomass was Accumulibacter, a confirmed polyphosphate accumulating organism (PAO) and when Candidatus 'Competibacter phosphatis', a confirmed glycogen-accumulating organism (GAO), was essentially undetectable. These experiments evaluated two different carbon sources (propionate and acetate), and in every case, two different P-release rates were detected. The highest rate took place while there was volatile fatty acid (VFA) in the mixed liquor, and after the VFA was depleted a second P-release rate was observed. This second rate was very similar to the one detected in experiments performed without added VFA.A kinetic and stoichiometric model developed as a modification of Activated Sludge Model 2 (ASM2) including glycogen economy, was fitted to the experimental profiles. The validation and calibration of this model was carried out with the cycle study experiments performed using both VFAs. The effect of pH from 6.5 to 8.0 on anaerobic P-release and VFA-uptake and aerobic P-uptake was also studied using propionate. The optimal overall working pH was around 7.5. This is the first study of the microbial community involved in EBPR developed with propionate as a sole carbon source along with detailed process performance investigations of the propionate-utilizing PAOs. Copyright 2003 Wiley Periodicals, Inc.

Possible role of substance P in the ischemia-reperfusion injury in the isolated rabbit lung.

PubMed

Arreola, José L; Vargas, Mario H; Segura, Patricia; Chávez, Jaime; Sommer, Bettina; Carvajal, Verónica; Montaño, Luis M

2004-07-27

The origin of the endothelial damage leading to the ischemia-reperfusion injury after lung transplantation has not been elucidated. We postulated that neurotransmitters released during the preservation of the donor lung might explain this vascular derangement. Thus, in isolated rabbit lungs preserved over 24 hours, we evaluated the release of acetylcholine (ACh) and substance P (SP), the activity of their major degrading enzymes, acetylcholinesterase (AChE) and neutral endopeptidase (NEP), and changes in the capillary permeability. Both neurotransmitters showed the highest release rate in the first 15 minutes, followed by a sharp exponential decrement at 1, 6, 12 and 24 hours. AChE and NEP activities showed no variation at these time intervals. Basal capillary permeability significantly increased (P<0.01) after 24 hours preservation with saline. This increased permeability was avoided (P<0.01) by the SP fragment 4-11 (an SP receptors antagonist), but not by atropine. These results suggest for the first time a pathogenic role of SP in the ischemia-reperfusion injury, and thus the potential usefulness of SP antagonists as additives in the lung preservation solutions should be explored.

Plastic debris retention and exportation by a mangrove forest patch.

PubMed

Ivar do Sul, Juliana A; Costa, Monica F; Silva-Cavalcanti, Jacqueline S; Araújo, Maria Christina B

2014-01-15

An experiment observed the behavior of selected tagged plastic items deliberately released in different habitats of a tropical mangrove forest in NE Brazil in late rainy (September) and late dry (March) seasons. Significant differences were not reported among seasons. However, marine debris retention varied among habitats, according to characteristics such as hydrodynamic (i.e., flow rates and volume transported) and relative vegetation (Rhizophora mangle) height and density. The highest grounds retained significantly more items when compared to the borders of the river and the tidal creek. Among the used tagged items, PET bottles were more observed and margarine tubs were less observed, being easily transported to adjacent habitats. Plastic bags were the items most retained near the releasing site. The balance between items retained and items lost was positive, demonstrating that mangrove forests tend to retain plastic marine debris for long periods (months-years). Copyright © 2013 Elsevier Ltd. All rights reserved.

Chlorotoxin-conjugated graphene oxide for targeted delivery of an anticancer drug

PubMed Central

Wang, Hao; Gu, Wei; Xiao, Ning; Ye, Ling; Xu, Qunyuan

2014-01-01

Current chemotherapy for glioma is rarely satisfactory due to low therapeutic efficiency and systemic side effects. We have developed a glioma-targeted drug delivery system based on graphene oxide. Targeted peptide chlorotoxin-conjugated graphene oxide (CTX-GO) sheets were successfully synthesized and characterized. Doxorubicin was loaded onto CTX-GO (CTX-GO/DOX) with high efficiency (570 mg doxorubicin per gram CTX-GO) via noncovalent interactions. Doxorubicin release was pH-dependent and showed sustained-release properties. Cytotoxicity experiments demonstrated that CTX-GO/DOX mediated the highest rate of death of glioma cells compared with free doxorubicin or graphene oxide loaded with doxorubicin only. Further, conjugation with chlorotoxin enhanced accumulation of doxorubicin within glioma cells. These findings indicate that CTX-GO is a promising platform for drug delivery and provide a rationale for developing a glioma-specific drug delivery system. PMID:24672236

Prioritization of Louisiana Parishes based on Industrial Releases of Known or Suspected Carcinogens.

PubMed

Katner, Adrienne

2015-01-01

This investigation evaluated the geographic distribution of carcinogen releases by Louisiana industries to prioritize areas for regulatory oversight, research and monitoring, and to promote clinician awareness and vigilance. Data on estimated industry releases for the period between 1996 and 2011 were obtained from the US Environmental Protection Agency's Toxics Release Inventory. Chemicals associated with cancers of the prostate, lung, bladder, kidney, breast and non-Hodgkin lymphoma were identified. The Risk Screening Environmental Indicators model was used to derive measures or model scores based on chemical toxicity, fate and transport, and population characteristics. Parishes, chemicals, industries and media generating the highest model scores were identified. Parishes with the highest model scores were East Baton Rouge, Calcasieu, Caddo and St. John the Baptist. Clinicians should carefully monitor cancer cases in these areas, and if patients reside near or work in industry, an occupational and environmental history should be considered.

Emissions of volatile organic compounds from new carpets measured in a large-scale environmental chamber

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hodgson, A.T.; Wooley, J.D.; Daisey, J.M.

1993-03-01

This study was undertaken to quantify the emissions of volatile organic compounds (VOCs) released by new carpets. Samples of four typical carpets, including two with styrene-butadiene rubber (SBR) latex adhesive and two with different backings, were collected from the finish lines at manufacturers' mills. Individual VOCs released from these samples were identified, and their concentrations, emission rates and mass emissions were measured under simulated indoor conditions in a 20 m[sup 3] environmental chamber over one week periods. Concentrations and emission rates of VOCs emitted by a new SBR carpet were also measured in a house. The carpets emitted a varietymore » of VOCs. The two SBR carpets primarily emitted 4-phenylcyclohexene (4-PCH), the source of [open quotes]new carpet[close quotes] odor, and styrene. The concentrations and emission rates of 4-PCH were similar for the two carpets, while the styrene values varied significantly. The carpet with a polyvinyl chloride backing emitted formaldehyde, vinyl acetate, isooctane, 1,2-propanediol, and 2-ethyl-1-hexanol. Of these, vinyl acetate and propanediol had the highest concentrations and emission rates. The carpet with a polyurethane backing primarily emitted butylated hydroxytoluene. With the exception of formaldehyde, little is known about the health effects of these VOCs at low concentrations. 23 refs., 3 figs., 6 tabs.« less

Dispersal of Warren root collar weevils (Coleoptera: Curculionidae) in three types of habitat.

PubMed

Machial, Laura A; Lindgren, B Staffan; Steenweg, Robin W; Aukema, Brian H

2012-06-01

Warren root collar weevil, Hylobius warreni Wood, is a native, flightless insect distributed throughout the boreal forest of North America. It is an emerging problem in young plantings of lodgepole pine, Pinus contorta variety latifolia, in western Canada, where larval feeding can kill young trees by girdling the root collar. Susceptible plantings are becoming more abundant following salvage harvesting and replanting activities in the wake of an ongoing epidemic of mountain pine beetle, Dendroctonus ponderosae (Hopkins). Previous studies using mark-trap-recapture methods found that movement rates of adult H. warreni were elevated in areas with high numbers of dead trees, consistent with a hypothesis that the insects immigrate from stands with high mountain pine beetle-caused tree mortality to young plantings in search of live hosts. Sampling methods were necessarily biased to insects captured in traps; however, potentially missing individuals that had died, left the study area, or simply remained stationary. Here, we used harmonic radar to examine weevil movement in three different habitats: open field, forest edge, and within a forest. We were able to reliably monitor all but two of 36 insects initially released, over 96 h (4 d). Weevils released in the open field had the highest rates of movement, followed by weevils released at the forest edge, then weevils released within the forest. Movement declined with decreasing ambient air temperature. Our results suggest that weevils tend to be relatively stationary in areas of live hosts, and hence may concentrate in a suitable area once such habitat is found.

Thyroid Cancer Detection by Ultrasound Among Residents Ages 18 Years and Younger in Fukushima, Japan: 2011 to 2014

PubMed Central

Tokinobu, Akiko; Yamamoto, Eiji; Suzuki, Etsuji

2016-01-01

Background: After the Great East Japan Earthquake and Tsunami in March 2011, radioactive elements were released from the Fukushima Daiichi Nuclear Power Plant. Based on prior knowledge, concern emerged about whether an increased incidence of thyroid cancer among exposed residents would occur as a result. Methods: After the release, Fukushima Prefecture performed ultrasound thyroid screening on all residents ages ≤18 years. The first round of screening included 298,577 examinees, and a second round began in April 2014. We analyzed the prefecture results from the first and second round up to December 31, 2014, in comparison with the Japanese annual incidence and the incidence within a reference area in Fukushima Prefecture. Results: The highest incidence rate ratio, using a latency period of 4 years, was observed in the central middle district of the prefecture compared with the Japanese annual incidence (incidence rate ratio = 50; 95% confidence interval [CI] = 25, 90). The prevalence of thyroid cancer was 605 per million examinees (95% CI = 302, 1,082) and the prevalence odds ratio compared with the reference district in Fukushima Prefecture was 2.6 (95% CI = 0.99, 7.0). In the second screening round, even under the assumption that the rest of examinees were disease free, an incidence rate ratio of 12 has already been observed (95% CI = 5.1, 23). Conclusions: An excess of thyroid cancer has been detected by ultrasound among children and adolescents in Fukushima Prefecture within 4 years of the release, and is unlikely to be explained by a screening surge. PMID:26441345

Risk analysis for dry snow slab avalanche release by skier triggering

NASA Astrophysics Data System (ADS)

McClung, David

2013-04-01

Risk analysis is of primary importance for skier triggering of avalanches since human triggering is responsible for about 90% of deaths from slab avalanches in Europe and North America. Two key measureable quantities about dry slab avalanche release prior to initiation are the depth to the weak layer and the slope angle. Both are important in risk analysis. As the slope angle increases, the probability of avalanche release increases dramatically. As the slab depth increases, the consequences increase if an avalanche releases. Among the simplest risk definitions is (Vick, 2002): Risk = (Probability of failure) x (Consequences of failure). Here, these two components of risk are the probability or chance of avalanche release and the consequences given avalanche release. In this paper, for the first time, skier triggered avalanches were analyzed from probability theory and its relation to risk for both the D and . The data consisted of two quantities : (,D) taken from avalanche fracture line profiles after an avalanche has taken place. Two data sets from accidentally skier triggered avalanches were considered: (1) 718 for and (2) a set of 1242 values of D which represent average values along the fracture line. The values of D were both estimated (about 2/3) and measured (about 1/3) by ski guides from Canadian Mountain Holidays CMH). I also analyzed 1231 accidentally skier triggered avalanches reported by CMH ski guides for avalanche size (representing destructive potential) on the Canadian scale. The size analysis provided a second analysis of consequences to verify that using D. The results showed that there is an intermediate range of both D and with highest risk. ForD, the risk (product of consequences and probability of occurrence) is highest for D in the approximate range 0.6 m - 1.0 m. The consequences are low for lower values of D and the chance of release is low for higher values of D. Thus, the highest product is in the intermediate range. For slope angles, the risk analysis showed there are two ranges: ˜ 320; × 460for which risk is lowest. In this case, both the range of and the consequences vary by about a factor of two so the probability of release dominates the risk analysis to yield low risk at the tails of the distribution of with highest risk in the middle (330 - 450) of the expected range (250 - 550).

Highly variable acquisition rates of Ixodes scapularis (Acari: Ixodidae) by birds on an Atlantic barrier island.

PubMed

Mitra, S S; Buckley, P A; Buckley, F G; Ginsberg, H S

2010-11-01

Acquisition of ticks by bird hosts is a central process in the transmission cycles of many tick-borne zoonoses, but tick recruitment by birds has received little direct study. We documented acquisition of Ixodes scapularis Say on birds at Fire Island, NY, by removing ticks from mist-netted birds, and recording the number of ticks on birds recaptured within 4 d of release. Eight bird species acquired at least 0.8 ticks bird(-1) day(-1) during the seasonal peak for at least one age class of I. scapularis. Gray Catbirds, Eastern Towhees, Common Yellowthroats, and Northern Waterthrushes collectively accounted for 83% of all tick acquisitions; and six individuals apportioned among Black-billed Cuckoo, Gray Catbird, Eastern Towhee, and Common Yellowthroat were simultaneously infested with both larvae and nymphs. Bird species with the highest acquisition rates were generally ground foragers, whereas birds that did not acquire ticks in our samples generally foraged above the ground. Tick acquisition by birds did not differ between deciduous and coniferous forests. Among the 15 bird species with the highest recruitment rates, acquisition of nymphs was not correlated with acquisition of larvae. Tick acquisition rates by individual bird species were not correlated with the reservoir competence of those species for Lyme borreliae. However, birds with high tick acquisition rates can contribute large numbers of infected ticks, and thus help maintain the enzootic cycle, even if their levels of reservoir competence are relatively low.

[Decomposition and nutrient release of root with different diameters of three subalpine dominant trees in western area of Sichuan Province, China].

PubMed

Tang, Shi-shan; Yang, Wan-qin; Wang, Hai-peng; Xiong, Li; Nie, Fu-yu; Xu, Shen-feng

2015-10-01

In this study, a buried bag experiment was used to investigate mass loss and C, N and P release patterns of fine (≤2 mm), medium (2-5 mm) and coarse (≥ 5 mm) roots of 3 subalpine dominant trees, i. e., Betula albosinensis, Abies faxoniana and Picea asperata in the growing and non-growing seasons. In general, the remaining mass of B. albosinensis was lower than that of A. faxoniana and P. asperata. In addition, root remaining mass increased with the increase of root diameter for the same species. The mass losing rate in the non-growing season was 52.1%-64.4% of a year. The C release of B. albosinensis was the highest, but that of A. faxoniana was the lowest. Also, C release decreased with the increase of root diameter. N of A. faxoniana and P. asperata were enriched in the non-growing season but released in the growing season. However, the opposite pattern was found for B. albosinensis. During the non-growing season, the amount of N enrichment increased with the increase of root diameter. The P release of 3 species was characterized as the enrichment-release pattern. P enrichment of A. faxoniana was significantly greater than that of P. asperata and B. albosinensis. Nevertheless, no significant difference was observed between diameter sizes. In conclusion, diameter size had significant effect on root decomposition in the subalpine forests of western Sichuan, and the diameter effect was dependent on tree species and season.

Release of nickel and chromium ions from orthodontic wires following the use of teeth whitening mouthwashes.

PubMed

Mirhashemi, AmirHossein; Jahangiri, Sahar; Kharrazifard, MohammadJavad

2018-02-05

Corrosion resistance is an important requirement for orthodontic appliances. Nickel and chromium may be released from orthodontic wires and can cause allergic reactions and cytotoxicity when patients use various mouthwashes to whiten their teeth. Our study aimed to assess the release of nickel and chromium ions from nickel titanium (NiTi) and stainless steel (SS) orthodontic wires following the use of four common mouthwashes available on the market. This in vitro, experimental study was conducted on 120 orthodontic appliances for one maxillary quadrant including five brackets, one band and half of the required length of SS, and NiTi wires. The samples were immersed in Oral B, Oral B 3D White Luxe, Listerine, and Listerine Advance White for 1, 6, 24, and 168 h. The samples immersed in distilled water served as the control group. Atomic absorption spectroscopy served to quantify the amount of released ions. Nickel ions were released from both wires at all time-points; the highest amount was in Listerine and the lowest in Oral B mouthwashes. The remaining two solutions were in-between this range. The process of release of chromium from the SS wire was the same as that of nickel. However, the release trend in NiTi wires was not uniform. Listerine caused the highest release of ions. Listerine Advance White, Oral B 3D White Luxe, and distilled water were the same in terms of ion release. Oral B showed the lowest amount of ion release.

SRTM Data Release for Africa, Colored Height

NASA Image and Video Library

2004-06-17

Elevation data at the highest possible resolution from NASA SRTM mission in February 2000 are being released for the first time for most of the African continent. This color shaded relief image shows the extent of SRTM digital elevation data for Africa.

Thermogravimetric-mass spectrometric analysis on combustion of lignocellulosic biomass.

PubMed

López-González, D; Fernandez-Lopez, M; Valverde, J L; Sanchez-Silva, L

2013-09-01

Combustion characteristics of biomass main components and three lignocellulosic biomass (fir wood, eucalyptus wood and pine bark) were investigated by thermogravimetric analysis coupled with mass spectrometry. The combustion of biomass was divided into two main steps, devolatilization and char oxidation stage. Heating rate effect was also studied. Generally, the higher the heating rate, the higher the decomposition temperature. Furthermore, the weight loss rate decreased due to particle temperature gradients. Combustion kinetics were studied. Models based on reaction order (Oi), nucleation (Ni) and diffusion (Di) achieved the best fitting to the experimental data. Cellulose oxidation presented the highest activation energies. CO, CO2 and H2O were the main components evolved from combustion. Additionally, light hydrocarbons (CH4 and C2H5) were also present. Finally, nitrogen compounds were in a higher proportion than sulfur compounds being released as primary amines and NOx. Copyright © 2013 Elsevier Ltd. All rights reserved.

Utilization of starch films plasticized with urea as fertilizer for improvement of plant growth.

PubMed

Rychter, Piotr; Kot, Marta; Bajer, Krzysztof; Rogacz, Diana; Šišková, Alena; Kapuśniak, Janusz

2016-02-10

The utilization of starch films, obtained by extrusion of potato starch with urea as plasticizer, for the fertilization of plants has been undertaken. Release rate of urea from the starch films was conducted in water conditions. The molecular weight distribution, surface erosion and weight loss of the starch samples have been determined. The evaluation of efficiency of urea as a fertilizer in the process of release from the starch films was performed under laboratory conditions based on the plant growth test proposed by OECD 208 Guideline and the PN-ISO International Standard using oat and common radish. Although among extruded starch-based films, those that contain the highest amount of fertilizer hold the most promise for a delayed release system, the time of release of fertilizer from obtained films in undertaken study was not satisfactory. All the same, in the present study effort has been made to utilize extruded samples as a fertilizer for agriculture or horticulture purposes. Urea-plasticized starch was successfully used as a fertilizer. Plant growth assessment, including determination of such parameters as fresh and dry matter of plants and their visual evaluation, has proved the stimulating effect of using extruded films on the growth and development of cultivated plants. Copyright © 2015 Elsevier Ltd. All rights reserved.

Catch and post-release mortalities of deep-water sharks caught by bottom longlines in the Cantabrian Sea (NE Atlantic)

NASA Astrophysics Data System (ADS)

Rodríguez-Cabello, Cristina; Sánchez, Francisco

2017-12-01

The majority of deep-water fish have very low capacity to survive discarding as fishery bycatch due to their biological characteristics and adaptation to depth. This study explores the catch and post-release mortalities of several deep-water shark species caught by bottom longline in the El Cachucho (Le Danois Bank) MPA in northern Spanish waters (NE Atlantic). Survivorship was qualitatively evaluated according to health condition and responses of individuals after capture and subsequent release. A total of 15 species were caught, of which the most abundant were leafscale gulper shark Centrophorus squamosus (39%), birdbeak dogfish Deania calcea (39%) and Portuguese dogfish Centroscymnus coelolepis (10%). Catch or at-vessel mortality (AVM) for these species was lower than expected, 1.2%, 8.8% and 4.5%, respectively but 18.9%, 37.4% and 38.6% including both those specimens dead on retrieval and those scored in poor condition). The species with the highest vitality rate was C. squamosus (37.3% in good condition; 43.8% in moderate condition), followed by D. calcea (22.8% in good condition; 39.8% in moderate condition) and C. coelolepis (6.8% and 54.5%). Post-release mortality (PRM) was examined using electronic tags (PSATs, n = 14). Of the nine C. squamosus tagged successfully, three died within 5-10 weeks after release, whereas the other six survived for periods of at least 45-120 days, when tags were programmed to release). In the case of C. coelolepis, two of the four tagged specimens died almost immediately after release, whereas the other two tags indicated that the fish survived immediate release, but data were too limited to gauge survival due to tag failure.

Low frequency ultrasonic-assisted hydrolysis of starch in the presence of α-amylase.

PubMed

Gaquere-Parker, Anne; Taylor, Tamera; Hutson, Raihannah; Rizzo, Ashley; Folds, Aubrey; Crittenden, Shastina; Zahoor, Neelam; Hussein, Bilal; Arruda, Aaron

2018-03-01

Hydrolysis of starch is an important process in the food industry and in the production of bioethanol or smaller carbohydrate molecules that can be used as starting blocks for chemical synthesis. Such hydrolysis can be enhanced by lowering the pH, heating the reaction mixture or catalyzing the reaction with enzymes. This study reports the effect of sonication on the reaction rate of starch hydrolysis at different temperatures, in the presence or absence of alpha-amylase. Starch Azure, a commercially available potato starch covalently linked with Remazol Brilliant Blue, has been chosen since its hydrolysis releases a blue dye, which concentration can be monitored by UV Vis spectroscopy. Ultrasounds, regardless of experimental conditions, provide the highest reaction rate for such hydrolysis. Copyright © 2017 Elsevier B.V. All rights reserved.

Investigations on phosphorus recovery and reuse as soil amendment from electric arc furnace slag filters.

PubMed

Bird, Simon C; Drizo, Aleksandra

2009-11-01

Electric arc furnace (EAF) steel slag has been identified as an effective filter material for the removal of phosphorus (P) from both point and non-point sources. To determine the feasibility of land-applying P saturated EAF steel slag this study was undertaken to investigate (i) saturated EAF steel slag material's potential as a P fertilizer or soil amendment and (ii) P desorption and metals leachate from saturated EAF steel slag material to surface runoff. Medicago sativa (alfalfa) was planted in a nutrient depleted washed sand media. Phosphorus was added either as saturated EAF steel slag or as a standard commercial phosphate fertilizer in order to assess the plant availability of the P from saturated EAF steel slag. Four different P application levels were tested: a low (20 lbs acre furrow slice(-1) (5.5 g P m(-3))) two medium (40 and 60 lbs. acre f.s.(-1) (11 and 16.5 g P m(-3))) and a high (120 lbs. acre f.s.(-1) (33 g P m(-3))). The above-ground biomass of half of the plants was harvested after 5 weeks and the second half at 10 weeks. All treatments regardless of the P source used showed high rates of germination. At the first harvest period (5 weeks) significantly higher above-ground biomass (p < 0.01) was seen at the 3 highest P amendment rates in treatments with triple super phosphate fertilizer (TSP) than with EAF steel slag. However, by the second harvest (10 weeks) only the highest amendment rate of TSP showed a significantly higher amount of biomass (p < 0.01), suggesting that EAF steel slag might be an effective slow release P source. In a second experiment, a rain simulator was used to assess desorption of DRP, TP and metals from a saturated and semi-saturated EAF steel slag. The results revealed that the total amounts of DRP and TP released to surface runoff from EAF steel slag were negligible when compared to the total quantities of P retained by this material. Overall the results from this study demonstrated that once the EAF steel slag filter reaches its saturation point, the material could be re-used as soil amendment for the slow release of bioavailable P with minimal risk for loss of P to surface runoff, bringing further benefits to the environment.

Characterization of elemental release during microbe basalt interactions at T = 28 °C

NASA Astrophysics Data System (ADS)

Wu, Lingling; Jacobson, Andrew D.; Chen, Hsin-Chieh; Hausner, Martina

2007-05-01

This study used batch reactors to characterize the rates and mechanisms of elemental release during the interaction of a single bacterial species ( Burkholderia fungorum) with Columbia River Flood Basalt at T = 28 °C for 36 days. We primarily examined the release of Ca, Mg, P, Si, and Sr under a variety of biotic and abiotic conditions with the aim of evaluating how actively metabolizing bacteria might influence basalt weathering on the continents. Four days after inoculating P-limited reactors (those lacking P in the growth medium), the concentration of viable planktonic cells increased from ˜10 4 to 10 8 CFU (Colony Forming Units)/mL, pH decreased from ˜7 to 4, and glucose decreased from ˜1200 to 0 μmol/L. Mass-balance and acid-base equilibria calculations suggest that the lowered pH resulted from either respired CO 2, organic acids released during biomass synthesis, or H + extrusion during NH4+ uptake. Between days 4 and 36, cell numbers remained constant at ˜10 8 CFU/mL and pH increased to ˜5. Purely abiotic control reactors as well as control reactors containing inert cells (˜10 8 CFU/mL) showed constant glucose concentrations, thus confirming the absence of biological activity in these experiments. The pH of all control reactors remained near-neutral, except for one experiment where the pH was initially adjusted to 4 but rapidly rose to 7 within 2 days. Over the entire 36 day period, P-limited reactors containing viable bacteria yielded the highest Ca, Mg, Si, and Sr release rates. Release rates inversely correlate with pH, indicating that proton-promoted dissolution was the dominant reaction mechanism. Both biotic and abiotic P-limited reactors displayed low P concentrations. Chemical analyses of bacteria collected at the end of the experiments, combined with mass-balances between the biological and fluid phases, demonstrate that the absence of dissolved P in the biotic reactors resulted from microbial P uptake. The only P source in the basalt is a small amount of apatite (˜1.2%), which occurs as needles within feldspar grains and glass. We therefore conclude that B. fungorum utilized apatite as a P source for biomass synthesis, which stimulated elemental release from coexisting mineral phases via pH lowering. The results of this study suggest that actively metabolizing bacteria have the potential to influence elemental release from basalt in continental settings.

Diurnal and Seasonal Variations of Eddy-Covariance Carbon Dioxide Fluxes Above an Urban Wetland, Partitioned by Vegetation Cover

NASA Astrophysics Data System (ADS)

Schafer, K. V.; Duman, T.

2017-12-01

The New Jersey Meadowlands are an urban brackish marsh with a long history of human activity causing disturbances and alterations. Carbon emissions were measured from two sites in the Meadowlands, a natural site and a restored site, using eddy-covariance (EC) from 2014 to 2016. At each site, the EC towers were placed at the interface of two vegetation covers, allowing capturing this aspect of the wetland's heterogeneity. Using footprint modeling and light response curves we were able to partition measured fluxes between vegetation cover types and compare CO2 fluxes from patches of invasive versus native wetland vegetation communities. We show that further separating the data into seasonal and diurnal fluxes reveals patterns in CO2 fluxes that allow determining the nature of each vegetation cover as a source or sink for CO2. Our results also show that CO2 emissions from the restored wetland are significantly higher than the natural wetland. Areas of invasive Phragmites australis at the natural site had the lowest CO2 release rates during winter. These were consistently lower in magnitude than summer daytime uptake, therefore making this part of the wetland a CO2 sink. Areas planted with native Spartina alterniflora at the restored site had the largest uptake during daytime, therefore seemingly justifying restoration activities. However, they also had the highest emission rates during summer nighttime, and therefore the daily summer net uptake was not the highest compared with other vegetation covers. Furthermore, emissions from the restored site during winter were larger compared to the natural site, indicating that restoration activities might have led to a significant increase of carbon release from the wetland. Thus, during the study period the restored wetland acted as a carbon source.

Fluoride release from glass ionomer restorative materials and the effects of surface coating.

PubMed

Hattab, F N; Amin, W M

2001-06-01

This in vitro study on fluoride (F) release from conventional and metal-reinforced glass ionomer investigated the following: (1) the release of F in deionized water compared to artificial saliva, (2) the effect of various surface coatings on F release, (3) the uptake of released F by hydroxyapatite, (4) the expression of the release data in a mathematical model, (5) F content in the powders and set materials, and (6) surface morphology of varnished and resin-coated specimens. Glass ionomer Ketac-Fil (KF), Fuji II (FJ), and Ketac-Silver (KS) were mixed according to the manufacturers' instructions, and prepared into specimens of 137.8 mm2 surface area. All three specimens were suspended in 50 ml of deionized water, artificial saliva, or aqueous solution of hydroxyapatite and submitted to constant agitation at 37 degrees C. In a separate experiment, the specimens were coated with varnish or light-cured bonding resin and tested for F release in solutions similar to those for uncoated specimens. The release of F occurred for 28 days. The concentration of F was measured with F-ion-specific electrode. All tested products showed a strong initial rate of F release which decreased with time until it reached a relatively steady rate after two weeks. The F released from KF and FJ was comparable in both pattern and magnitude. They released approximately four times more F than KS. In all cases, the release of F in artificial saliva was significantly (p < 0.001) less than in deionized water. Surface coating the specimens significantly reduced the F release ( p < 0.05 top < 0.001, depending on the product and type of coating). The inhibitory effect of coating markedly decreased with time. Resin coating reduced F release more than varnish in KF and KS, but not for FJ. Essentially, all F released in aqueous solution was taken up by the hydroxyapatite, with FJ ranking the highest in increasing hydroxyapatite F concentration. Over the 28 days, the quantities of F released from FJ, KF, and KS were, respectively, 3.8, 2.3, and 1.0% of the total F content in the specimens. The F concentration in the set KS was 53.9 and 72.5% of that found in KF and FJ, respectively. The release data as a function of time were best described by the power curve. Micromorphological examinations revealed remnants of surface coatings on specimens after 14 days storage in artificial saliva. Glass ionomer cements released significantly less F in artificial saliva than in deionized water. Surface coating the specimens substantially reduced F release. These clinically relevant factors were not considered by many in vitro release studies which overestimate the F availability from glass ionomers. A recall appointment 24 h after the placement of glass ionomer restoration should be given for surface finishing.

The simulated air flow pattern around a moving animal transport vehicle as the basis for a prospective biosecurity risk assessment.

PubMed

Seedorf, Jens; Schmidt, Ralf-Gunther

2017-08-01

Research that investigates bioaerosol emissions from animal transport vehicles (ATVs) and their importance in the spread of harmful airborne agents while the ATVs travel on roads is limited. To investigate the dynamical behaviour of theoretically released particles from a moving ATV, the open-source computational fluid dynamics (CFD) software OpenFOAM was used to calculate the external and internal air flow fields with passive and forced ventilated openings of a common ATV moving at a speed of 80 km/h. In addition to a computed flow rate of approximately 40,000 m 3 /h crossing the interior of the ATV, the visualization of the trajectories has demonstrated distinct patterns of the spatial distribution of potentially released bioaerosols in the vicinity of the ATV. Although the front openings show the highest air flow to the outside, the recirculations of air masses between the interior of the ATV and the atmosphere also occur, which complicate the emission and the dispersion characterizations. To specify the future emission rates of ATVs, a database of bioaerosol concentrations within the ATV is necessary in conjunction with high-performance computing resources to simulate the potential dispersion of bioaerosols in the environment.

Effect of the Ethanol Injection Moment During Compression Stroke on the Combustion of Ethanol - Diesel Dual Direct Injection Engine

NASA Astrophysics Data System (ADS)

Liang, Yu; Zhou, Liying; Huang, Haomin; Xu, Mingfei; Guo, Mei; Chen, Xin

2018-01-01

A set of GDI system is installed on a F188 single-cylinder, air-cooled and direct injection diesel engine, which is used for ethanol injection, with the injection time controlled by the crank angle signal collected by AVL angle encoder. The injection of ethanol amounts to half of the thermal equivalent of an original diesel fuel. A 3D combustion model is established for the ethanol - diesel dual direct injection engine. Diesel was injected from the original fuel injection system, with a fuel supply advance angle of 20°CA. The ethanol was injected into the cylinder during compression process. Diesel injection began after the completion of ethanol injection. Ethanol injection starting point of 240°CA, 260°CA, 280°CA, 300°CA and 319.4°CA were simulated and analyzed. Due to the different timing of ethanol injection, the ignition of the ethanol mixture when diesel fires, results in non-uniform ignition distribution and flame propagation rate, since the distribution and concentration gradients of the ethanol mixture in the cylinder are different, thus affecting the combustion process. The results show that, when ethanol is injected at 319.4°CA, the combustion heat release rate and the pressure rise rate during the initial stage are the highest. Also, the maximum combustion pressure, with a relatively advance phase, is the highest. In case of later initial ethanol injection, the average temperature in the cylinder during the initial combustion period will have a faster rise. In case of initial injection at 319.4°CA, the average temperature in the cylinder is the highest, followed by 240°CA ethanol injection. In the post-combustion stage, the earlier ethanol injection will result in higher average temperature in the cylinder and more complete fuel combustion. The injection of ethanol at 319.4°CA produces earlier and highest NOX emissions.

Postrelease monitoring of radio-instrumented sea otters in Prince William Sound

USGS Publications Warehouse

Monnett, C.; Rotterman, L.M.; Stack, C.; Monson, Daniel H.; Bayha, Keith; Kormendy, Jennifer

1990-01-01

Sea otters (Enhydra lutris) that were captured in western Prince William Sound (PWS) or the Gulf of Alaska, treated, and held in captivity at the temporary rehabilitation centers established in response to the T/V Exxon Valdez oil spill were instrumented with radio transmitters, released into eastern PWS, and monitored by radiotelemetry. We undertook the present study to gain information for guiding the release of the remaining captive otters and evaluating the efficacy of sea otter rehabilitation after exposure to crude oil. Radio transmitters were attached to the flippers of seven sea otters released in May 1989 and monitored for periods of a few hours to more than 60 days. However, little was learned about the fate of these animals because the radio transmitters used proved unreliable. Forty-five additional sea otters from the rehabilitation centers were implanted with radio transmitters, released into northeastern PWS and monitored for 8 months. During the first 20 days after the first release of these implanted otters (n = 21), they were more mobile than wild-caught and released sea otters studied in PWS, from 1984 through 1990. All were alive and vigorous at the end of the 20-day period. Tracking of all 45 implanted sea otters during the 8-month period showed that the otters remained highly mobile. Many (46.6%) crossed into western PWS. However, by the end of the 8 months, 12 of the instrumented otters were dead and 9 were missing. One radio failed. These mortality and missing rates are much higher than those normally observed for adult sea otters in PWS. The death rate was highest in winter. These data suggest that, despite the tremendous amount of money and energy directed toward the treatment and care of these animals, the sea otters released from the centers were not completely rehabilitated, that is, not returned to a normal state. We recommend that future policies focus on preventing otters from becoming oiled, rather than attempting to treat them after oiling has occurred. This focus is especially recommended because of stress and disease risks associated with bringing wild animals into captivity.

Sexual Violence Inside Prisons: Rates of Victimization

PubMed Central

Blitz, Cynthia L.; Shi, Jing; Bachman, Ronet; Siegel, Jane A.

2006-01-01

People in prison are exposed to and experience sexual violence inside prisons, further exposing them to communicable diseases and trauma. The consequences of sexual violence follow the individual into the community upon release. This paper estimates the prevalence of sexual victimization within a state prison system. A total of 6,964 men and 564 women participated in a survey administered using audio-CASI. Weighted estimates of prevalence were constructed by gender and facility size. Rates of sexual victimization varied significantly by gender, age, perpetrator, question wording, and facility. Rates of inmate-on-inmate sexual victimization in the previous 6 months were highest for female inmates (212 per 1,000), more than four times higher than male rates (43 per 1,000). Abusive sexual conduct was more likely between inmates and between staff and inmates than nonconsensual sexual acts. Sexual violence inside prison is an urgent public health issue needing targeted interventions to prevent and ameliorate its health and social consequences, which spatially concentrate in poor inner-city areas where these individuals ultimately return. PMID:16937087

Impact of Soil Heavy Metal Pollution on Food Safety in China.

PubMed

Zhang, Xiuying; Zhong, Taiyang; Liu, Lei; Ouyang, Xiaoying

2015-01-01

Food safety is a major concern for the Chinese public. This study collected 465 published papers on heavy metal pollution rates (the ratio of the samples exceeding the Grade II limits for Chinese soils, the Soil Environmental Quality Standard-1995) in farmland soil throughout China. The results showed that Cd had the highest pollution rate of 7.75%, followed by Hg, Cu, Ni and Zn, Pb and Cr had the lowest pollution rates at lower than 1%. The total pollution rate in Chinese farmland soil was 10.18%, mainly from Cd, Hg, Cu, and Ni. The human activities of mining and smelting, industry, irrigation by sewage, urban development, and fertilizer application released certain amounts of heavy metals into soil, which resulted in the farmland soil being polluted. Considering the spatial variations of grain production, about 13.86% of grain production was affected due to the heavy metal pollution in farmland soil. These results many provide valuable information for agricultural soil management and protection in China.

Impact of Soil Heavy Metal Pollution on Food Safety in China

PubMed Central

Zhang, Xiuying; Zhong, Taiyang; Liu, Lei; Ouyang, Xiaoying

2015-01-01

Food safety is a major concern for the Chinese public. This study collected 465 published papers on heavy metal pollution rates (the ratio of the samples exceeding the Grade II limits for Chinese soils, the Soil Environmental Quality Standard-1995) in farmland soil throughout China. The results showed that Cd had the highest pollution rate of 7.75%, followed by Hg, Cu, Ni and Zn, Pb and Cr had the lowest pollution rates at lower than 1%. The total pollution rate in Chinese farmland soil was 10.18%, mainly from Cd, Hg, Cu, and Ni. The human activities of mining and smelting, industry, irrigation by sewage, urban development, and fertilizer application released certain amounts of heavy metals into soil, which resulted in the farmland soil being polluted. Considering the spatial variations of grain production, about 13.86% of grain production was affected due to the heavy metal pollution in farmland soil. These results many provide valuable information for agricultural soil management and protection in China. PMID:26252956

Annual variation in condition, respiration and remineralisation of Mytilus edulis L. in the Sound, Denmark

NASA Astrophysics Data System (ADS)

Schlüter, L.; Josefsen, S. B.

1994-12-01

By means of monthly in situ incubations, variations in oxygen uptake, nutrient release and C/N-ratio were monitored during a period of 14 months of a mussel population ( Mytilus edulis L.) located on an exposed beach. A condition index calculated as weight/length3 showed that the condition of the mussels was highest in the spring. Specific oxygen uptake and nutrient release had separate maxima, with high oxygen uptake in the spring coinciding with a period of growth, and high nutrient release during summer when the temperature was highest. Oxygen uptake was significantly correlated with both the condition of the mussels and the temperature, while ammonium release was significantly correlated only with the temperature. Except in spring, the oxygen uptake, condition index and O/N-ratio were low, indicating a poor condition of the mussels. The mussels suffered from suboptimal conditions caused by inadequate food supply and failed to accumulate glycogen reserves essential for the development of mature gametes.

Effect of ozonolysis pretreatment parameters on the sugar release, ozone consumption and ethanol production from sugarcane bagasse.

PubMed

Travaini, Rodolfo; Barrado, Enrique; Bolado-Rodríguez, Silvia

2016-08-01

A L9(3)(4) orthogonal array (OA) experimental design was applied to study the four parameters considered most important in the ozonolysis pretreatment (moisture content, ozone concentration, ozone/oxygen flow and particle size) on ethanol production from sugarcane bagasse (SCB). Statistical analysis highlighted ozone concentration as the highest influence parameter on reaction time and sugars release after enzymatic hydrolysis. The increase on reaction time when decreasing the ozone/oxygen flow resulted in small differences of ozone consumptions. Design optimization for sugars release provided a parameters combination close to the best experimental run, where 77.55% and 56.95% of glucose and xylose yields were obtained, respectively. When optimizing the grams of sugar released by gram of ozone, the highest influence parameter was moisture content, with a maximum yield of 2.98gSUGARS/gO3. In experiments on hydrolysates fermentation, Saccharomyces cerevisiae provided ethanol yields around 80%, while Pichia stipitis was completely inhibited. Copyright © 2016 Elsevier Ltd. All rights reserved.

Community-specific biogeochemical responses to atmospheric nitrogen deposition in subalpine meadow ecosystems of the Cascade Range

NASA Astrophysics Data System (ADS)

Poinsatte, J. P.; Rochefort, R.; Evans, R. D.

2014-12-01

Elevated anthropogenic nitrogen (N) emissions result in higher rates of atmospheric N deposition (Ndep) that can saturate sensitive ecosystems. Consequences of increased Ndep include higher emissions of greenhouse gases, eutrophication of watersheds, and deterioration of vegetation communities. Most of the annual N deposition at higher elevations in the Cascades is stored in snowpack until spring snowmelt when it is released as a pulse that can be assimilated by plant and microbial communities, or lost as gaseous emissions or leachate. The relative magnitude of these fluxes is unknown, particularly with accelerated rates of snowpack loss due to climate change. We quantified storage of Ndep in winter snowpack and determined impacts of Ndep on biogeochemical processes in a lush-herbaceous community characterized by Valeriana sitchensis and Lupinus latifolius, a heath-shrub community characterized by Phyllodoce empetriformis and Cassiope mertensiana, and a wet-sedge community dominated by Carex nigricans. These communities were selected to represent early, mid, and late snowmelt vegetation regimes prevalent throughout the Cascades. Ammonium (NH4+) was the dominant form of Ndep in winter snowpack and Ndep rates were higher than anticipated based on nearby National Atmospheric Deposition Program (NADP) measurements. Vegetation N uptake was the dominant N sink in the ecosystem, with the highest growing season uptake occurring in the lush-herbaceous community, while soil N leaching was the dominant N loss, with the lush-herbaceous also having the highest rates. Microbial biomass N fluctuated substantially across the growing season, with high biomass N immediately after snowmelt and again 30 days following snow release. Soil nitrous oxide (N2O) emissions peaked 30 days following snowmelt for all three communities and were greatest in the wet sedge community. These results indicate that subalpine communities have unique responses to Ndep that vary throughout the growing season. Thus, biogeochemical modeling efforts to simulate ecosystem responses to Ndep should be parameterized at a community-specific level to fully capture this variability. Ultimately, this study will provide insight to land managers on the fate of N emissions and how Ndep affects ecosystem services in high-elevation ecosystems.

Mapping the Spatial Distribution of CO2 release from Kīlauea Volcano, Hawaii, USA

NASA Astrophysics Data System (ADS)

Elias, T.; Werner, C. A.; Kern, C.; Sutton, A. J.; Hauri, E. H.; Kelly, P. J.

2014-12-01

Kīlauea Volcano is a large emitter of volcanic CO2 with emission rates ranging from 7500-30,000 t/d. However, Kīlauea presents a challenging situation for CO2 emission rate measurement in that the main source of SO2 is the active vent in Halema'uma'u Crater, whereas CO2 emits mainly from a large (> 1km2) diffuse region east of the vent. Previous researchers recognized this issue and advocated for the use of a plume-integrated concentration ratio paired with the SO2 emission to determine CO2 emission rates; however, this worked best prior to the opening of the summit vent in 2008, or when SO2emission was still diffuse as opposed to focused degassing from the vent. We used two techniques to study the spatial distribution and temporal variability of CO2 release from the summit caldera in July, 2014. Eddy covariance measurements made at 14 locations in the area of diffuse emission resulted in elevated fluxes that generally ranged from 500 to > 5000 g/m2d, or typical of other volcanic and hydrothermal areas worldwide. MultiGas measurements of the CO2 and SO2 concentration in air at 1-m above the ground identified approximately seven areas of elevated area of CO2 degassing in the caldera. The CO2 concentrations in air were spatially well correlated to approximately 100 m and displayed anisotropy that was consistent with the measured wind direction. Areas of highest CO2 concentration correlated with the areas of highest flux using the eddy covariance method and were found near the middle of the caldera approximately 1 km NE of the active vent. This area overlies the inferred location of the shallow summit reservoir, and is characterized by linear fractures with adhered sublimate deposits at the surface. A few of the fractures are visibly fuming, but much of the degassing in the area is not apparent. Future work includes monitoring the fluxes in this area over time, and attempting to quantify emission rates from the areas of measured flux.

Detailed source term estimation of the atmospheric release for the Fukushima Daiichi Nuclear Power Station accident by coupling simulations of an atmospheric dispersion model with an improved deposition scheme and oceanic dispersion model

NASA Astrophysics Data System (ADS)

Katata, G.; Chino, M.; Kobayashi, T.; Terada, H.; Ota, M.; Nagai, H.; Kajino, M.; Draxler, R.; Hort, M. C.; Malo, A.; Torii, T.; Sanada, Y.

2015-01-01

Temporal variations in the amount of radionuclides released into the atmosphere during the Fukushima Daiichi Nuclear Power Station (FNPS1) accident and their atmospheric and marine dispersion are essential to evaluate the environmental impacts and resultant radiological doses to the public. In this paper, we estimate the detailed atmospheric releases during the accident using a reverse estimation method which calculates the release rates of radionuclides by comparing measurements of air concentration of a radionuclide or its dose rate in the environment with the ones calculated by atmospheric and oceanic transport, dispersion and deposition models. The atmospheric and oceanic models used are WSPEEDI-II (Worldwide version of System for Prediction of Environmental Emergency Dose Information) and SEA-GEARN-FDM (Finite difference oceanic dispersion model), both developed by the authors. A sophisticated deposition scheme, which deals with dry and fog-water depositions, cloud condensation nuclei (CCN) activation, and subsequent wet scavenging due to mixed-phase cloud microphysics (in-cloud scavenging) for radioactive iodine gas (I2 and CH3I) and other particles (CsI, Cs, and Te), was incorporated into WSPEEDI-II to improve the surface deposition calculations. The results revealed that the major releases of radionuclides due to the FNPS1 accident occurred in the following periods during March 2011: the afternoon of 12 March due to the wet venting and hydrogen explosion at Unit 1, midnight of 14 March when the SRV (safety relief valve) was opened three times at Unit 2, the morning and night of 15 March, and the morning of 16 March. According to the simulation results, the highest radioactive contamination areas around FNPS1 were created from 15 to 16 March by complicated interactions among rainfall, plume movements, and the temporal variation of release rates. The simulation by WSPEEDI-II using the new source term reproduced the local and regional patterns of cumulative surface deposition of total 131I and 137Cs and air dose rate obtained by airborne surveys. The new source term was also tested using three atmospheric dispersion models (Modèle Lagrangien de Dispersion de Particules d'ordre zéro: MLDP0, Hybrid Single Particle Lagrangian Integrated Trajectory Model: HYSPLIT, and Met Office's Numerical Atmospheric-dispersion Modelling Environment: NAME) for regional and global calculations, and the calculated results showed good agreement with observed air concentration and surface deposition of 137Cs in eastern Japan.

Terbinafine-loaded wound dressing for chronic superficial fungal infections.

PubMed

Paskiabi, Farnoush Asghari; Bonakdar, Shahin; Shokrgozar, Mohammad Ali; Imani, Mohammad; Jahanshiri, Zahra; Shams-Ghahfarokhi, Masoomeh; Razzaghi-Abyaneh, Mehdi

2017-04-01

In spite of developing new drugs and modern formulations, the treatments of chronic fungal infections are still challenging. Fibrous wound dressings are new suggestions for the treatment of chronic superficial infections. In the present study, we formulated an antifungal agent, terbinafine hydrochloride (TFH), which is a hydrophobic drug, in wound dressings prepared by electrospun polycaprolactone, polycaprolactone/gelatin (50:50 w/w) and gelatin. To obtain more water-stable meshes, the preparations were treated by glutaraldehyde and their properties were determined before and after treatment. The morphology of fibrous meshes was observed by scanning electron microscopy. Drug loading efficiency and release rate were measured by high performance liquid chromatography (HPLC) and the release rate was monitored for 144h. Antifungal tests were performed on Trichophyton mentagrophytes, Aspergillus fumigatus and Candida albicans cultured on Muller-Hinton agar. The toxicity of the meshes was measured after 24h and 14days by MTT assay. Terbinafine loading of polycaprolactone/gelatin (50:50) was 100% and it released the highest amount of TFH too. In antifungal tests, all samples were able to hinderT. mentagrophytes and A. fumigatus but not C. albicans growth among them, polycaprolactone fibers made the largest inhibition zone. In MTT assay, none of prepared samples showed toxicity against L929 cells. Teken together, the prepared TFH-loaded PCL/gelatin electrospun meshes were able to release TFH slowly and in a steady state in time. With respect to no obvious cytotoxicity in MTT assay and stong antifungal activity toward T. mentagrophytesin vitro, these TFH-based meshes could be considered as potential candidates in clinical application as wound dressing for treatment of chronic dermatophytosis. Copyright © 2016 Elsevier B.V. All rights reserved.

Hydraulic architecture and photosynthetic capacity as constraints on release from suppression in Douglas-fir and western hemlock.

PubMed

Renninger, Heidi J; Meinzer, Frederick C; Gartner, Barbara L

2007-01-01

We compared hydraulic architecture, photosynthesis and growth in Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco), a shade-intolerant species, and western hemlock (Tsuga heterophylla (Raf.) Sarg.), a shade-tolerant species, to study the temporal pattern of release from suppressive shade. In particular, we sought to determine whether hydraulic architecture or photosynthetic capacity is most important in constraining release. The study was conducted at two sites with mixed stands of 10- to 20-year-old Douglas-fir and western hemlock. At one site, the stand had been thinned allowing release of the understory trees, whereas at the other site, the stand remained unthinned. Douglas-fir had lower height growth (from 1998-2003) and lower relative height growth (height growth from 1998 to 2003/height in 1998) than western hemlock. However, relative height growth of released versus suppressed trees was higher in Douglas-fir (130%) than in western hemlock (65%), indicating that, although absolute height growth was less, Douglas-fir did release from suppression. Release seemed to be constrained initially by a limited photosynthetic capacity in both species. Five years after release, Douglas-fir trees had 14 times the leaf area and 1.5 times the leaf nitrogen concentration (N (area)) of suppressed trees. Needles of released western hemlock trees had about twice the maximum assimilation rate (A (max)) at ambient [CO(2)] as needles of suppressed trees and exhibited no photoinhibition at the highest irradiances. After release, trees increased in leaf area, leaf N concentration and overall photosynthetic capacity. Subsequently, hydraulic architecture appeared to constrain release in Douglas-fir and, to a lesser extent, in western hemlock. Released trees had significantly less negative foliar delta(13)C values than suppressed trees and showed a positive relationship between leaf area:sapwood area ratio (A (L)/A (S)) and delta(13)C, suggesting that trees with more leaf area for a given sapwood area experienced a stomatal limitation on carbon gain. Nonetheless, these changes had no significant effects on leaf specific conductivities of suppressed versus released trees of either species, but leaf specific root conductance was significantly lower in released Douglas-fir.

Process relevant screening of cellulolytic organisms for consolidated bioprocessing.

PubMed

Antonov, Elena; Schlembach, Ivan; Regestein, Lars; Rosenbaum, Miriam A; Büchs, Jochen

2017-01-01

Although the biocatalytic conversion of cellulosic biomass could replace fossil oil for the production of various compounds, it is often not economically viable due to the high costs of cellulolytic enzymes. One possibility to reduce costs is consolidated bioprocessing (CBP), integrating cellulase production, hydrolysis of cellulose, and the fermentation of the released sugars to the desired product into one process step. To establish such a process, the most suitable cellulase-producing organism has to be identified. Thereby, it is crucial to evaluate the candidates under target process conditions. In this work, the chosen model process was the conversion of cellulose to the platform chemical itaconic acid by a mixed culture of a cellulolytic fungus with Aspergillus terreus as itaconic acid producer. Various cellulase producers were analyzed by the introduced freeze assay that measures the initial carbon release rate, quantifying initial cellulase activity under target process conditions. Promising candidates were then characterized online by monitoring their respiration activity metabolizing cellulose to assess the growth and enzyme production dynamics. The screening of five different cellulase producers with the freeze assay identified Trichoderma   reesei and Penicillium   verruculosum as most promising. The measurement of the respiration activity revealed a retarded induction of cellulase production for P.   verruculosum but a similar cellulase production rate afterwards, compared to T.   reesei . The freeze assay measurement depicted that P.   verruculosum reaches the highest initial carbon release rate among all investigated cellulase producers. After a modification of the cultivation procedure, these results were confirmed by the respiration activity measurement. To compare both methods, a correlation between the measured respiration activity and the initial carbon release rate of the freeze assay was introduced. The analysis revealed that the different initial enzyme/cellulose ratios as well as a discrepancy in cellulose digestibility are the main differences between the two approaches. With two complementary methods to quantify cellulase activity and the dynamics of cellulase production for CBP applications, T.   reesei and P.   verruculosum were identified as compatible candidates for the chosen model process. The presented methods can easily be adapted to screen for suitable cellulose degrading organisms for various other applications.

Reformulation of controlled-release oxycodone and pharmacy dispensing patterns near the US-Canada border.

PubMed

Gomes, Tara; Paterson, J Michael; Juurlink, David N; Dhalla, Irfan A; Mamdani, Muhammad M

2012-01-01

In August 2010, a tamper-resistant formulation of controlled-release oxycodone (OxyContin-OP) was introduced in the United States but not in Canada. Our objective was to determine whether introduction of OxyContin-OP in the United States influenced prescription volumes for the original controlled-release oxycodone formulation (OxyContin) at Canadian pharmacies near the international border. We conducted a population-based, serial, cross-sectional study of prescriptions dispensed from pharmacies in the 3 cities with the highest volume of US-Canada border crossings in Ontario: Niagara Falls, Windsor and Sarnia. We analyzed data on all outpatient prescriptions for OxyContin dispensed by Canadian pharmacies near each border crossing between 2010 Apr. 1 and 2012 Feb. 29. We calculated and compared monthly prescription rates, adjusted per 1000 population and stratified by tablet strength. The number of tablets dispensed near 4 border crossings in the 3 Canadian cities remained stable over the study period. However, the rate of dispensing at pharmacies near the Detroit-Windsor Tunnel increased roughly 4-fold between August 2010 and February 2011, from 505 to 1969 tablets per 1000 population. By April 2011, following warnings to prescribers and pharmacies regarding drug-seeking behaviour, the dispensing rate declined to 1683 tablets per 1000 population in this area. By November 2011, the rate had returned to levels observed in early 2010. Our analyses suggest that 242 075 excess OxyContin tablets were dispensed near the Detroit-Windsor Tunnel between August 2010 and October 2011. Prescribing of the original formulation of controlled-release oxycodone rose substantially near a major international border crossing following the introduction of a tamper-resistant formulation in the United States. It is possible that the restriction of this finding to the area surrounding the Detroit-Windsor Tunnel reflects specific characteristics of this border crossing, including its high traffic volume, direct access to the downtown core and drug-trafficking patterns in the Detroit area. Our findings highlight the potential impact of cross-border differences in medication availability on drug-seeking behaviour.

Effects of crosslinking on the mechanical properties, drug release and cytocompatibility of protein polymers.

PubMed

Martinez, Adam W; Caves, Jeffrey M; Ravi, Swathi; Li, Wehnsheng; Chaikof, Elliot L

2014-01-01

Recombinant elastin-like protein polymers are increasingly being investigated as component materials of a variety of implantable medical devices. This is chiefly a result of their favorable biological properties and the ability to tailor their physical and mechanical properties. In this report, we explore the potential of modulating the water content, mechanical properties, and drug release profiles of protein films through the selection of different crosslinking schemes and processing strategies. We find that the selection of crosslinking scheme and processing strategy has a significant influence on all aspects of protein polymer films. Significantly, utilization of a confined, fixed volume, as well as vapor-phase crosslinking strategies, decreased protein polymer equilibrium water content. Specifically, as compared to uncrosslinked protein gels, water content was reduced for genipin (15.5%), glutaraldehyde (GTA, 24.5%), GTA vapor crosslinking (31.6%), disulfide (SS, 18.2%) and SS vapor crosslinking (25.5%) (P<0.05). Distinct crosslinking strategies modulated protein polymer stiffness, strain at failure and ultimate tensile strength (UTS). In all cases, vapor-phase crosslinking produced the stiffest films with the highest UTS. Moreover, both confined, fixed volume and vapor-phase approaches influenced drug delivery rates, resulting in decreased initial drug burst and release rates as compared to solution phase crosslinking. Tailored crosslinking strategies provide an important option for modulating the physical, mechanical and drug delivery properties of protein polymers. Copyright © 2013 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Response ofMeteorus leviventris, (Hymenoptera: Braconidae) to mustard oils in field trapping experiments.

PubMed

Pivnick, K A

1993-09-01

Trapping experiments were carried out near Saskatoon, Canada, from May through August 1990 to assess the response of the braconid wasp,Meteorus leviventris, to four selected mustard oils or isothiocyanates (IC) at a release rate of 4 mg/day, and for allyl IC only, at 40 mg/day. Only allyl IC at 4 mg/day was significantly attractive when trap captures were compared to the captures in the control traps. The others (n-propyl IC, 2-phenylethyl IC., and ethyl IC) were not attractive, nor was allyl IC at the higher dose, although trap captures with the latter bait were the second highest.

Controlled release of metformin from chitosan-based nanocomposite films containing mesoporous MCM-41 nanoparticles as novel drug delivery systems.

PubMed

Shariatinia, Zahra; Zahraee, Zahra

2017-09-01

Biocompatible nanocomposite films based on blended chitosan and poly(ethylene glycol)-block-poly(propylene glycol)-block-poly(ethylene glycol) (BP) polymers containing metformin (MET) drug and MCM-41 or MCM-41-APS (APS=aminopropylsilane) nanoparticles (NPs) were designed and fabricated in order to prepare novel drug delivery systems which are useful for controlled drug release purposes. The total pore volume and mesopore volume of MCM-41 were measured equal to 1.08 and 1.05 cm 3 /g but those of MCM-41-APS were 0.54 and 0.26 cm 3 /g indicating smaller values for the APS functionalized material. The film thickness was the highest for CS-BP-G-10%MET (70μm) but it was the smallest for the CS-BP-G-4%MCM-41 (49μm). For all of the films, the swelling percent was the highest in acidic medium but it was decreased in PBS and the least water uptake occurred in the alkaline environment. The lowest and the highest water uptake was observed for the films incorporated with 4%MCM-41NPs and 4%MCM-41-APS-10%MET, respectively. The SEM micrographs of the films after three days water uptake in pH=4 medium exhibited that all of the films were stable against cracking and/or tearing. It was found that increasing the MCM-41 or MCM-41-APS amount within the films decreased the elongation at break but enhanced the tensile stress. The release of the MET was sharply increased within ∼22-24h (burst release) but after that the drug release was slowly enhanced during 15days (sustained release). Finally, it was concluded that the film 4% MCM-41-APS-10%MET NPs was the most promising drug delivery system because it had improved hydrophilicity, hydrolytic stability, biocompatibility, mechanical and drug release properties. Copyright © 2017 Elsevier Inc. All rights reserved.

Impact of Release Rates on the Effectiveness of Augmentative Biological Control Agents

PubMed Central

Crowder, David W.

2007-01-01

To access the effect of augmentative biological control agents, 31 articles were reviewed that investigated the impact of release rates of 35 augmentative biological control agents on the control of 42 arthropod pests. In 64% of the cases, the release rate of the biological control agent did not significantly affect the density or mortality of the pest insect. Results where similar when parasitoidsor predators were utilized as the natural enemy. Within any order of natural enemy, there were more cases where release rates did not affect augmentative biological control than cases where release rates were significant. There were more cases in which release rates did not affect augmentative biological control when pests were from the orders Hemiptera, Acari, or Diptera, but not with pests from the order Lepidoptera. In most cases, there was an optimal release rate that produced effective control of a pest species. This was especially true when predators were used as a biological control agent. Increasing the release rate above the optimal rate did not improve control of the pest and thus would be economically detrimental. Lower release rates were of ten optimal when biological control was used in conjunction with insecticides. In many cases, the timing and method of biological control applications were more significant factors impacting the effectiveness of biological control than the release rate. Additional factors that may limit the relative impact of release rates include natural enemy fecundity, establishment rates, prey availability, dispersal, and cannibalism. PMID:20307240

Arsenic release and speciation during the oxidative dissolution of arsenopyrite by O2 in the absence and presence of EDTA.

PubMed

Wang, Shaofeng; Jiao, BeiBei; Zhang, Mingmei; Zhang, Guoqing; Wang, Xin; Jia, Yongfeng

2018-03-15

The oxidative decomposition of arsenopyrite is an important source of As in surface environment. This study investigated the oxidative dissolution of arsenopyrite by O 2 and aqueous arsenic transformation at different pHs, dissolved oxygen (DO) contents, and temperatures in the absence and presence of EDTA. The oxidative dissolution was greatly inhibited at neutral and alkaline pH in the absence of EDTA. However, in the presence of EDTA, the oxidative dissolution rate increased linearly from pH 4 to 7. The highest dissolution rate was 3-4 times higher than that at pH 4 and 1-2 orders of magnitude higher than that at pH 7 in the absence of EDTA. This is possibly due to the lack of Fe oxyhydroxides on the surface of arsenopyrite. In the pH range of 7-10, the oxidative dissolution rate decreased linearly, possibly due to the formation of goethite and/or hematite coating. The oxidation of released arsenite (As III ) to arsenate (As V ) took place simultaneously during the oxidative dissolution of arsenopyrite in the presence of dissolved Fe without EDTA, while no obvious aqueous As III oxidation was observed in the presence of EDTA, indicating that aqueous Fe species play an important role in As III oxidation. Copyright © 2017 Elsevier B.V. All rights reserved.

ENERGY EFFICIENT VAPOR PHASE OXIDATION OF METHANOL USING OZONE AND CATALYTIC REACTOR

EPA Science Inventory

The pulp and paper industry releases more than 144 million tons of Volatile Organic Compounds (VOCs) per year. A big portion of this effluent, 66+% is released to air making it the fourth highest contributor of VOC emissions to the atmosphere by industry sector [1]. The current...

Suppression of GHS-R in AgRP neurons mitigates diet-induced obesity by activating thermogenesis

USDA-ARS?s Scientific Manuscript database

Ghrelin, an orexigenic hormone released primarily from the gut, signals the hypothalamus to stimulate growth hormone release, enhance appetite and promote weight gain. The ghrelin receptor, aka Growth Hormone Secretagogue Receptor (GHS-R), is highly expressed in the brain, with highest expression in...

Marijuana, phytocannabinoids, the endocannabinoid system, and male fertility.

PubMed

du Plessis, Stefan S; Agarwal, Ashok; Syriac, Arun

2015-11-01

Marijuana has the highest consumption rate among all of the illicit drugs used in the USA, and its popularity as both a recreational and medicinal drug is increasing especially among men of reproductive age. Male factor infertility is on the increase, and the exposure to the cannabinoid compounds released by marijuana could be a contributing cause. The endocannabinoid system (ECS) is deeply involved in the complex regulation of male reproduction through the endogenous release of endocannabinoids and binding to cannabinoid receptors. Disturbing the delicate balance of the ECS due to marijuana use can negatively impact reproductive potential. Various in vivo and in vitro studies have reported on the empirical role that marijuana plays in disrupting the hypothalamus-pituitary-gonadal axis, spermatogenesis, and sperm function such as motility, capacitation, and the acrosome reaction. In this review, we highlight the latest evidence regarding the effect of marijuana use on male fertility and also provide a detailed insight into the ECS and its significance in the male reproductive system.

The modulatory role of cytokines IL-4 and IL-17 in the functional activity of phagocytes in diabetic pregnant women.

PubMed

Fagundes, Danny L G; França, Eduardo L; Gonzatti, Michelangelo B; Rugde, Marilza V C; Calderon, Iracema M P; Honorio-França, Adenilda C

2018-01-01

The study investigated the role of cytokines IL-4 and IL-17 in the modulation of the functional activity of mononuclear phagocytes in diabetic pregnant women with hyperglycemia. Sixty pregnant women were assigned to the following groups: nondiabetic (ND), mild gestational hyperglycemia (MGH), gestational diabetes mellitus (GDM), or type 2 diabetes mellitus (DM2). The functional activity of phagocytes from maternal blood, cord blood, and colostrum was assessed by determining their superoxide release, phagocytosis, microbicidal activity, and intracellular Ca 2+ release. Irrespective of glycemic status, colostrum and blood cells treated with IL-4 and IL-17 increased superoxide release in the presence of enteropathogenic Escherichia coli (EPEC). The highest phagocytosis rate was observed in cells from the DM2 group treated with IL-4. In all the groups, phagocytes from colostrum, maternal blood, and cord blood exhibited higher microbicidal activity against EPEC when treated with cytokines. IL-17 increased intracellular Ca 2+ release by colostrum phagocytes in diabetic groups. The results indicate that the IL-4 and IL-17 modulate the functional activity of phagocytes in the maternal blood, cord blood, and colostrum of diabetic mother. The natural immunity resulting from the interaction between the cells and cytokines tested may be an alternative procedure to improve the prognosis of maternal and newborn infections. © 2017 APMIS. Published by John Wiley & Sons Ltd.

Results of 2 decades of injury surveillance and public release of data in the Australian Football League.

PubMed

Orchard, John W; Seward, Hugh; Orchard, Jessica J

2013-04-01

Injuries are common in all professional football codes (including soccer, rugby league and union, American football, Gaelic football, and Australian football). To report the epidemiology of injuries in the Australian Football League (AFL) from 1992-2012 and to identify changes in injury patterns during that period. Descriptive epidemiology study. The AFL commenced surveying injuries in 1992, with all teams and players included since 1996. An injury was defined as "any physical or medical condition that causes a player to miss a match in the regular season or finals (playoffs)." Administrative records of injury payments (which are compulsory as part of salary cap compliance) to players who do not play matches determined the occurrence of an injury. The seasonal incidence was measured in units of new injuries per club (of 40 players) per season (of 22 matches). There were 4492 players listed over the 21-year period who suffered 13,606 new injuries/illnesses and 1965 recurrent injuries/illnesses, which caused 51,919 matches to be missed. The lowest seasonal incidence was 30.3 new injuries per club per season recorded in 1993, and the highest was 40.3 recorded in 1998. The injury prevalence (missed matches through injury per club per season) varied from a low of 116.3 in 1994 to a high of 157.1 in 2011. The recurrence rate of injuries was highest at 25% in 1992 and lowest at 9% in 2012 and has steadily fallen across the 21 years (P < .01). The most frequent and prevalent injury was hamstring strain (average of 6 injuries per club per season, resulting in 20 missed matches per club per season; recurrence rate, 26%), although the rate of hamstring injuries has fallen in the past 2 seasons after a change to the structure of the interchange bench (P < .05). The rate of knee posterior cruciate ligament injuries fell in the years after a rule change to prevent knee-to-knee collisions in ruckmen (P < .01). Annual public reporting (by way of media release and reports available freely online) of injury rates, using units easily understood by laypeople, has been well received. It has also paved the way for rule changes with the primary goal of improving player safety.

Morbidity, outcomes and cost-benefit analysis of wildlife rehabilitation in Catalonia (Spain)

PubMed Central

Molina-López, Rafael Angel; Mañosa, Santi; Torres-Riera, Alex; Pomarol, Manel

2017-01-01

Background There are few studies of careful examination of wildlife casualties in Wildlife Rehabilitation Centers. These studies are essential for detecting menaces to wild species and providing objective criteria about cost-benefit of treatments in those centers. The release rate is considered the main outcome indicator, but other parameters such as length of stay at the center and a cost-benefit index expressed as number of released animals per euro and day, could be used as reliable estimators of the rehabilitation costs. Methodology A retrospective study based on 54772 admissions recorded from 1995–2013 in the database of the Wildlife Rehabilitation Center of Torreferrussa (Catalonia, NW Spain) assessed the morbidity, outcomes and cost-benefits of the rehabilitation practices. Results Three hundred and two species were included: 232 birds (n = 48633), 37 mammals (n = 3293), 20 reptiles (n = 2705) and 13 amphibians (n = 141). The most frequent causes of admission were: 39.8% confiscation of protected species (89.4% passerines), 31.8% orphaned young animals (35.3% swifts, 21.7% diurnal raptors and owls) and 17.4% trauma casualties (46.7% raptors and owls). The highest proportion of releases was found in the captivity confiscation category [87.4% passerines (median time of stay: 12 days)], followed by the orphaned category [78% owls (66 days), 76.5% diurnal birds of prey (43 days), 75.6% hedgehogs (49 days), 52.7% swifts (19 days) and 52% bats (55 days)]. For the trauma group, 46.8% of releases were hedgehogs (44 days) and 25.6% owls (103 days). As regards the cost-benefit index, the trauma casualties and infectious diseases had the worse values with 1.3 and 1.4 released animals/euro/day respectively, and were particularly low in raptors, waders, marine birds and chiroptera. On the contrary, captivity (4.6) and misplacement (4.1) had the best index, particulary in amphibian, reptiles and passerines. Conclusions/significance Cost-benefit studies including the release rate, the time of stay at the center and the cost-benefit index should be implemented for improving management efficiency of the Wildlife Rehabilitation Centers. PMID:28719647

Release of chemical permeation enhancers from drug-in-adhesive transdermal patches.

PubMed

Qvist, Michael H; Hoeck, Ulla; Kreilgaard, Bo; Madsen, Flemming; Frokjaer, Sven

2002-01-14

There is only limited knowledge of how chemical permeation enhancers release from transdermal drug delivery systems of the drug-in-adhesive type. In this study, the release of eight commonly known enhancers from eight types of polymer adhesives was evaluated using Franz diffusion cells. It was shown that all the enhancers released completely from the adhesives and followed a square root of time kinetic (Higuchi law). Using a statistical analysis it was shown that the release rate was more dependent on the type of enhancer than on the type of polymers. The mean release rates were in the range from 2.2 to 11.1%/ radical t for the slowest and fastest releasing enhancers, which correspond to a 50% release within 500 and 20 min, respectively. Furthermore, the release rates were inversely proportional to the cube root of the molal volumes of the enhancers and to their logarithmic partition coefficients between the polymer adhesive and the receptor fluid. It was found that the observed release rates were probably due to a high diffusion coefficient of the enhancers rather than due to an inhomogeneous embedment of the enhancers in the adhesives. The type of adhesive showed minor influence on the release rate, especially among the acrylic polymers no difference was seen. However, compared to the acrylic adhesives, the polyisobutylene adhesive showed slower release rates, while the silicone adhesive showed slightly faster release rates.

Effects of solubilizing surfactants and loading of antiviral, antimicrobial, and antifungal drugs on their release rates from ethylene vinyl acetate copolymer

PubMed Central

Tallury, Padmavathy; Randall, Marcus K; Thaw, Khin L; Preisser, John S.; Kalachandra, Sid

2013-01-01

Objectives This study investigates the effects of surfactants and drug loading on the drug release rate from ethylene vinyl acetate (EVA) copolymer. The release rate of nystatin from EVA was studied with addition of non-ionic surfactants Tween 60 and Cremophor RH 40. In addition, the effect of increasing drug load on the release rates of nystatin, chlorhexidine diacetate and acyclovir is also presented. Method Polymer casting solutions were prepared by stirring EVA copolymer and nystatin (2.5 wt %) in dichloromethane. Nystatin and surfactants were added in ratios of (1:1), (1:2) and (1:3). Drug loading was studied with 2.5, 5.0, 7.5, and 10.0% wt. proportions of nystatin, chlorhexidine diacetate and acyclovir incorporated into a separate polymer. Three drug loaded polymer square films (3cm × 3cm × 0.08 cm) were cut from dry films to follow the kinetics of drug release at 37°C. 10 ml of either distilled water or PBS was used as the extracting medium that was replaced daily. PBS was used for nystatin release with addition of surfactants and water was used for the study on drug loading and surfactant release. The rate of drug release was measured by UV-spectrophotometer. The amount of surfactant released was determined by HPLC. Results The release of nystatin was low in PBS and its release rate increased with the addition of surfactants. Also, increasing surfactant concentrations resulted in increased drug release rates. The release rates of chlorhexidine diacetate (p<0.0001), acyclovir (p<0.0003) and nystatin (p<0.0017) linearly increased with increasing drug loads. The amount of surfactants released was above the CMC. Significance This study demonstrates that the three therapeutic agents show a sustained rate of drug release from EVA copolymer over extended periods of time. Nystatin release in PBS is low owing to its poor solubility. Its release rate is enhanced by addition of surfactants and increasing the drug load as well. PMID:17049593

Human prolactin - 24-hour pattern with increased release during sleep.

NASA Technical Reports Server (NTRS)

Sassin, J. F.; Weitzman, E. D.; Kapen, S.; Frantz, A. G.

1972-01-01

Human prolactin was measured in plasma by radioimmunoassay at 20-minute intervals for a 24-hour period in each of six normal adults, whose sleep-wake cycles were monitored polygraphically. A marked diurnal variation in plasma concentrations was demonstrated, with highest values during sleep. Periods of episodic release occurred throughout the 24 hours.

In situ release rates of Cu and Zn from commercial antifouling paints at different salinities.

PubMed

Lagerström, Maria; Lindgren, J Fredrik; Holmqvist, Albin; Dahlström, Mia; Ytreberg, Erik

2018-02-01

Antifouling paints are environmentally risk assessed based on their biocidal release rates to the water phase. In situ release rates of copper (Cu) and zinc (Zn) were derived for five commercial paints in two recreational marinas with different salinities (5 and 14 PSU) using an X-Ray Fluorescence spectrometer (XRF). Salinity was found to significantly affect the Cu release, with twice the amount of Cu released at the higher salinity, while its influence on the Zn release was paint-specific. Site-specific release rates for water bodies with salinity gradients, e.g. the Baltic Sea, are therefore necessary for more realistic risk assessments of antifouling paints. Furthermore, the in situ release rates were up to 8 times higher than those generated using standardized laboratory or calculation methods. The environmental risk assessment repeated with the field release rates concludes that it is questionable whether the studied products should be allowed on the Swedish market. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Swelling, erosion and drug release characteristics of salbutamol sulfate from hydroxypropyl methylcellulose-based matrix tablets.

PubMed

Chaibva, Faith A; Khamanga, Sandile M M; Walker, Roderick B

2010-12-01

Hydrophilic matrix formulations are important and simple technologies that are used to manufacture sustained release dosage forms. Hydroxypropyl methylcellulose-based matrix tablets, with and without additives, were manufactured to investigate the rate of hydration, rate of erosion, and rate and mechanism of drug release. Scanning electron microscopy was used to assess changes in the microstructure of the tablets during drug release testing and whether these changes could be related to the rate of drug release from the formulations. The results revealed that the rate of hydration and erosion was dependent on the polymer combination(s) used, which in turn affected the rate and mechanism of drug release from these formulations. It was also apparent that changes in the microstructure of matrix tablets could be related to the different rates of drug release that were observed from the test formulations. The use of scanning electron microscopy provides useful information to further understand drug release mechanisms from matrix tablets.

Potential differentiation ability of gingiva originated human mesenchymal stem cell in the presence of tacrolimus

PubMed Central

Ha, Dong-Ho; Pathak, Shiva; Yong, Chul Soon; Kim, Jong Oh; Jeong, Jee-Heon; Park, Jun-Beom

2016-01-01

The aim of the present study is to evaluate the potential differentiation ability of gingiva originated human mesenchymal stem cell in the presence of tacrolimus. Tacrolimus-loaded poly(lactic-co-glycolic acid) microspheres were prepared using electrospraying technique. In vitro release study of tacrolimus-loaded poly(lactic-co-glycolic acid) microspheres was performed in phosphate-buffered saline (pH 7.4). Gingiva-derived stem cells were isolated and incubated with tacrolimus or tacrolimus-loaded microspheres. Release study of the microspheres revealed prolonged release profiles of tacrolimus without any significant initial burst release. The microsphere itself did not affect the morphology of the mesenchymal stem cells, and cell morphology was retained after incubation with microspheres loaded with tacrolimus at 1 μg/mL to 10 μg/mL. Cultures grown in the presence of microspheres loaded with tacrolimus at 1 μg/mL showed the highest mineralization. Alkaline phosphatase activity increased with an increase in incubation time. The highest expression of pSmad1/5 was achieved in the group receiving tacrolimus 0.1 μg/mL every third day, and the highest expression of osteocalcin was achieved in the group receiving 1 μg/mL every third day. Biodegradable poly(lactic-co-glycolic acid)-based microspheres loaded with tacrolimus promoted mineralization. Microspheres loaded with tacrolimus may be applied for increased osteoblastic differentiation. PMID:27721434

Water- and Fertilizer-Integrated Hydrogel Derived from the Polymerization of Acrylic Acid and Urea as a Slow-Release N Fertilizer and Water Retention in Agriculture.

PubMed

Cheng, Dongdong; Liu, Yan; Yang, Guiting; Zhang, Aiping

2018-05-31

To reduce the preparation cost of superabsorbent and improve the N release rate at the same time, a novel low-cost superabsorbent (SA) with the function of N slow release was prepared by chemical synthesis with neutralized acrylic acid (AA), urea, potassium persulfate (KPS), and N, N'-methylenebis(acrylamide) (MBA). The order of influence factors on the water absorbency property was determined by an orthogonal L 18 (3) 7 experiment. On the basis of the optimization results of the orthogonal experiment, the effects of a single factor on the water absorption were investigated, and the highest water absorbency (909 g/g) was achieved for the conditions of 1.0 mol urea/mol AA ratio, 100% of AA neutralized, K + , 1.5% KPS to AA mass fraction, 0.02% MBA to AA mass fraction, 45 °C reaction temperature, and 4.0 h reaction time. The optimal sample was characterized by scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR). Swelling behaviors of the superabsorbent were investigated in distilled water and various soil and salt solutions. The water-release kinetics of SA in different negative pressures and soils were systematically investigated. Additionally, the maize seed germination in various types of soil with different amounts of SA was proposed, and the N could release 3.71% after being incubated in distilled water for 40 days. After 192 h, the relative water content of SA-treated sandy loam, loam, and paddy soil were 42, 56, and 45%, respectively. All of the results in this work showed that SA had good water retention and slow N-release properties, which are expected to have potential applications in sustainable modern agriculture.

Life Cycle Assessment and Release Studies for 15 Nanosilver-Enabled Consumer Products: Investigating Hotspots and Patterns of Contribution.

PubMed

Pourzahedi, Leila; Vance, Marina; Eckelman, Matthew J

2017-06-20

Increasing use of silver nanoparticles (AgNPs) in consumer products as antimicrobial agents has prompted extensive research toward the evaluation of their potential release to the environment and subsequent ecotoxicity to aquatic organisms. It has also been shown that AgNPs can pose significant burdens to the environment from life cycle emissions associated with their production, but these impacts must be considered in the context of actual products that contain nanosilver. Here, a cradle-to-gate life cycle assessment for the production of 15 different AgNP-enabled consumer products was performed, coupled with release studies of those same products, thus providing a consistent analytical platform for investigation of potential nanosilver impacts across a range of product types and concentrations. Environmental burdens were assessed over multiple impact categories defined by the United States Environmental Protection Agency's Tool for the Reduction and Assessment of Chemical and Other Environmental Impacts (TRACI 2.1) method. Depending on the product composition and silver loading, the contribution of AgNP synthesis to the overall impacts was seen to vary over a wide range from 1% to 99%. Release studies found that solid polymeric samples lost more silver during wash compared to fibrous materials. Estimates of direct ecotoxicity impacts of AgNP releases from those products with the highest leaching rates resulted in lower impact levels compared to cradle-to-gate ecotoxicity from production for those products. Considering both cradle-to-gate production impacts and nanoparticle release studies, in conjunction with estimates of life cycle environmental and health benefits of nanoparticle incorporation, can inform sustainable nanoenabled product design.

The proteome of exudates from germinating Lupinus albus seeds is secreted through a selective dual-step process and contains proteins involved in plant defence.

PubMed

Scarafoni, Alessio; Ronchi, Alessandro; Prinsi, Bhakti; Espen, Luca; Assante, Gemma; Venturini, Giovanni; Duranti, Marcello

2013-03-01

The general knowledge of defence activity during the first steps of seed germination is still largely incomplete. The present study focused on the proteins released in the exudates of germinating white lupin seeds. During the first 24 h, a release of proteins was observed. Initially (i.e. during the first 12 h), the proteins found in exudates reflected the composition of the seed, indicating a passive extrusion of pre-formed proteins. Subsequently, when the rate of protein release was at its highest, the composition of the released proteome changed drastically. This transition occurred in a short time, indicating that more selective and regulated events, such as secretory processes, took place soon after the onset of germination. The present study considered: (a) the characterization of the proteome accumulated in the germinating medium collected after the appearance of the post-extrusion events; (b) the biosynthetic origin and the modalities that are the basis of protein release outside the seeds; and (c) an assessment of antifungal activity of these exudates. The most represented protein in the exudate was chitinase, which was synthesized de novo. The other proteins are involved in the cellular mechanisms responding to stress events, including biotic ones. This exudate was effectively able to inhibit fungal growth. The results of the present study indicate that seed exudation is a dual-step process that leads to the secretion of selected proteins and thus is not a result of passive leakage. The released proteome is involved in protecting the spermosphere environment and thus may act as first defence against pathogens. © 2013 The Authors Journal compilation © 2013 FEBS.

Bringing it all back home: Understanding the medical difficulties encountered by newly released prisoners in New Orleans, Louisiana - a qualitative study.

PubMed

Vail, William Lee; Niyogi, Anjali; Henderson, Norris; Wennerstrom, Ashley

2017-07-01

Formerly incarcerated persons (FIPs) face a disproportionate risk of death and serious illness in the immediate post-release period. Therefore, it is a critical time to initiate community-based care for chronic illnesses and behavioural disorders. Little is known about the unique transitional health and social support needs of FIPs in Louisiana, which has the highest incarceration rate in the world. As the average age of prisoners in the United States rises, the release of older prisoners with chronic conditions will become increasingly common. The aim of this study was to explore the healthcare experiences of FIPs in Louisiana in order to inform delivery of services tailored to this population. This research was done in partnership with a community organisation that advocates for restoration of voting rights to FIPs and helps newly released individuals transition back into society. This organisation identified FIPs in the Greater New Orleans area, and from January to May 2015, we conducted 24 semi-structured, in-person, audio-recorded interviews at the community organisation's transitional living facility. The interviews assessed FIPs' experiences with and barriers to receiving healthcare during and after incarceration. These discussions also explored FIPs' desires for services and attitudes towards health and healthcare. Interviews were transcribed and independently coded by two researchers. Interviewees reported negative experiences with healthcare during incarceration, and limited health guidance during the pre-release process. Post-release concerns included lack of insurance, difficulty accessing care and medication, and interest in learning about healthy lifestyles. Results suggest a need for a formalised system of transitional healthcare for FIPs. Findings are being used to inform a pilot transitional care clinic in New Orleans, Louisiana. © 2017 John Wiley & Sons Ltd.

Sustained release of stromal cell derived factor-1 from an antioxidant thermoresponsive hydrogel enhances dermal wound healing in diabetes.

PubMed

Zhu, Yunxiao; Hoshi, Ryan; Chen, Siyu; Yi, Ji; Duan, Chongwen; Galiano, Robert D; Zhang, Hao F; Ameer, Guillermo A

2016-09-28

Diabetic foot ulcers (DFUs) are a severe complication of diabetes mellitus. Altered cell migration due to microcirculatory deficiencies as well as excessive and prolonged reactive oxygen species production are implicated in the delayed healing of DFUs. The goal of this research was to assess whether sustained release of SDF-1, a chemokine that promotes endothelial progenitor cell homing and angiogenesis, from a citrate-based antioxidant thermoresponsive polymer would significantly improve impaired dermal wound healing in diabetes. Poly (polyethylene glycol citrate-co-N-isopropylacrylamide) (PPCN) was synthesized via sequential polycondensation and free radical polymerization reactions. SDF-1 was entrapped via gelation of the PPCN+SDF-1 solution above its lower critical solution temperature (LCST) and its release and bioactivity was measured. The effect of sustained release of SDF-1 from PPCN (PPCN+SDF-1) versus a bolus application of SDF-1 in phosphate buffered saline (PBS) on wound healing was evaluated in a diabetic murine splinted excisional dermal wound model using gross observation, histology, immunohistochemistry, and optical coherence tomography microangiography. Increasing PPCN concentration decreased SDF-1 release rate. The time to 50% wound closure was 11days, 16days, 14days, and 17days for wounds treated with PPCN+SDF-1, SDF-1 only, PPCN only, and PBS, respectively. Wounds treated with PPCN+SDF-1 had the shortest time for complete healing (24days) and exhibited accelerated granulation tissue production, epithelial maturation, and the highest density of perfused blood vessels. In conclusion, sustained release of SDF-1 from PPCN is a promising and easy to use therapeutic strategy to improve the treatment of chronic non-healing DFUs. Copyright © 2016 Elsevier B.V. All rights reserved.

Phosphorus retention and sorption by constructed wetland soils in Southeast Ireland.

PubMed

Dunne, E J; Culleton, N; O'Donovan, G; Harrington, R; Daly, K

2005-11-01

It may be necessary to use constructed wetlands as a land use practice to mitigate phosphorus (P) loss from agriculture in Ireland. The objectives of this study were to determine the ability of two constructed wetland site soils to retain and sorb P. Intact soil/water column studies were used to determine P release/retention rates during a 30-day incubation period. Soil columns flooded with distilled water released P during the first 2 days; however, soluble reactive P (SRP) concentrations in overlying floodwaters decreased thereafter. Soils with overlying floodwaters spiked at 5 and 15 mg SRP L(-1) retained highest amounts of P (p < 0.05) with retention at these concentrations controlled by SRP in overlying waters. Retention rates by soils ranged between 0.3 and 60.9 mg Pm(-2) d(-1). Maximum P sorption capacity (Smax) was higher for wetland soils at Dunhill, Waterford (1464 mg P kg(-1)) in comparison to soils at Johnstown Castle, Wexford (618 mg P kg(-1)). Equilibrium P concentrations (EPC0) were low (in the microg SRP L(-1) range), indicating a high capacity of these soils to sorb P. Phosphorus sorption parameters were significantly related to ammonium oxalate extractable aluminium (Al) and iron (Fe) content of soils.

Acetoclastic methane formation from Eucalyptus detritus in pristine hydrocarbon-rich river sediments by Methanosarcinales.

PubMed

Beckmann, Sabrina; Manefield, Mike

2014-12-01

Pristine hydrocarbon-rich river sediments in the Greater Blue Mountains World Heritage Area (Australia) release substantial amounts of methane. The present study aimed to unravel for the first time the active methanogens mediating methane formation and exploiting the bacterial diversity potentially involved in the trophic network. Quantitative PCR of 16S rRNA gene and functional genes as well as 454 pyrosequencing were used to address the unknown microbial diversity and abundance. Methane-releasing sediment cores derived from three different river sites of the Tootie River. Highest methane production rates of 10.8 ± 0.5 μg g(-1)(wet weight) day(-1) were detected in 40 cm sediment depth being in congruence with the detection of the highest abundances of the archaeal 16S rRNA gene and the methyl-coenzyme M reductase (mcrA) genes. Stable carbon and hydrogen isotopic signatures of the produced methane indicated an acetoclastic origin. Long-term enrichment cultures amended with either acetate or H2/CO2 revealed acetoclastic methanogenesis as key methane-formation process mediated by members of the order Methanosarcinales. Conditions prevailing in the river sediments might be suitable for hydrocarbon-degrading bacteria observed in the river sediments that were previously unclassified or closely related to the Bacteroidetes/Chlorobi group, the Firmicutes and the Chloroflexi group fuelling acetoclastic methanogensis in pristine river sediments. © 2014 Federation of European Microbiological Societies. Published by John Wiley & Sons Ltd. All rights reserved.

Improved estimates of environmental copper release rates from antifouling products.

PubMed

Finnie, Alistair A

2006-01-01

The US Navy Dome method for measuring copper release rates from antifouling paint in-service on ships' hulls can be considered to be the most reliable indicator of environmental release rates. In this paper, the relationship between the apparent copper release rate and the environmental release rate is established for a number of antifouling coating types using data from a variety of available laboratory, field and calculation methods. Apart from a modified Dome method using panels, all laboratory, field and calculation methods significantly overestimate the environmental release rate of copper from antifouling coatings. The difference is greatest for self-polishing copolymer antifoulings (SPCs) and smallest for certain erodible/ablative antifoulings, where the ASTM/ISO standard and the CEPE calculation method are seen to typically overestimate environmental release rates by factors of about 10 and 4, respectively. Where ASTM/ISO or CEPE copper release rate data are used for environmental risk assessment or regulatory purposes, it is proposed that the release rate values should be divided by a correction factor to enable more reliable generic environmental risk assessments to be made. Using a conservative approach based on a realistic worst case and accounting for experimental uncertainty in the data that are currently available, proposed default correction factors for use with all paint types are 5.4 for the ASTM/ISO method and 2.9 for the CEPE calculation method. Further work is required to expand this data-set and refine the correction factors through correlation of laboratory measured and calculated copper release rates with the direct in situ environmental release rate for different antifouling paints under a range of environmental conditions.

Nickel Ion Release from Three Types of Nickel-titanium-based Orthodontic Archwires in the As-received State and After Oral Simulation

PubMed Central

Ramazanzadeh, Barat Ali; Ahrari, Farzaneh; Sabzevari, Berahman; Habibi, Samaneh

2014-01-01

Background and aims. This study aimed to investigate release of nickel ion from three types of nickel-titanium-based wires in the as-received state and after immersion in a simulated oral environment. Materials and methods. Forty specimens from each of the single-strand NiTi (Rematitan "Lite"), multi-strand NiTi (SPEED Supercable) and Copper NiTi (Damon Copper NiTi) were selected. Twenty specimens from each type were used in the as-received state and the others were kept in deflected state at 37ºC for 2 months followed by autoclave sterilization. The as-received and recycled wire specimens were immersed in glass bottles containing 1.8 mL of artificial saliva for 28 days and the amount of nickel ion released into the electrolyte was determined using atomic absorption spectrophotometry. Results. The single-strand NiTi released the highest quantity of nickel ion in the as-received state and the multi-strand NiTi showed the highest ion release after oral simulation. The quantity of nickelion released from Damon Copper NiTi was the lowest in both conditions. Oral simulation followed by sterilization did not have a significant influence on nickel ion release from multi-strand NiTi and Damon Copper NiTi wires, but single-strand NiTi released statistically lower quantities of nickel ion after oral simulation. Conclusion. The multi-strand nature of Supercable did not enhance the potential of corrosion after immersion in the simulated oral environment. In vitro use of nickel-titanium-based archwires followed by sterilization did not significantly increase the amount of nickel ion released from these wires. PMID:25093049

Harvest and reporting rates of game-farm ring-necked pheasants

USGS Publications Warehouse

Diefenbach, D.R.; Riegner, C.F.; Hardisky, T.S.

2000-01-01

Many state natural resource agencies release ring-necked pheasants (Phasianus colchicus) for hunting, but the effectiveness of these programs has never been evaluated on a statewide basis. We conducted a reward-band study to estimate harvest, reporting, and survival rates of pheasants raised and released by the Pennsylvania Game Commission (PGC) for the fall 1998 hunting season. We banded 6,770 of 199,613 released pheasants with leg bands worth $0-$400. Rewards >$75 produced 100% reporting rates. Hunters reported 71.0% of harvested pheasants banded with standard bands (no reward). Cocks had an estimated 62.3% harvest rate when released on public land and a 46.8% harvest rate on private land. Hens had an estimated 50.4% harvest rate when released on public land and a 31.1% harvest rate on private land. Estimated harvest rate for hen pheasants released in September in the either-sex zone was 15.5%. In the late season, pheasants released on public land had a 33.6% harvest rate and a 23.5% harvest rate on private land. We found that few pheasants (30 days and birds released on public land had reduced survival rates primarily because of greater harvest rates. In fiscal year 1998-99, the net cost to raise and release 199,613 pheasants was $2,813,138 ($14.09 per bird). The average cost per harvested pheasant was $29.10, but ranged from $22.63 to $90.74 depending on the date and location of release. We estimated that 49.9% (82,017 birds) of pheasants stocked immediately prior to and during the regular and late seasons (excluding September releases of hens) were harvested by hunters. Percentage of pheasants harvested by hunters could be increased by expanding the either-sex zone in Pennsylvania so that more hens could be legally killed by hunters and by allocating releases to seasons and locations with greater harvest rates. However, before such changes are implemented, we recommend a survey of Pennsylvania pheasant hunters to ascertain their opinions and desires regarding releases of game-farm pheasants.

Bionomics of Asian Citrus Psyllid (Hemiptera: Liviidae) Associated with Orange Jasmine Hedges in Southeast Central Florida, with Special Reference to Biological Control by Tamarixia radiata.

PubMed

Hall, David G; Rohrig, Eric

2015-06-01

The Asian citrus psyllid, Diaphorina citri Kuwayama, is an important pest in Florida because it transmits bacteria responsible for citrus huanglongbing disease. In addition to infesting citrus, orange jasmine (Murraya exotica L.) is one of Asian citrus psyllid's preferred host plants and is widely grown as an ornamental hedge. We report on Asian citrus psyllid bionomics over three years at five urban plantings of orange jasmine and on biological control of Asian citrus psyllid by a parasitoid Tamarixia radiata (Waterston). T. radiata had been released in Florida shortly after Asian citrus psyllid was first found, and the parasitoid was known to be established at each planting. Additionally, three new T. radiata haplotypes were released every 3 wk at three plantings during the first study year (one haplotype per planting, over all releases an average of 17 parasitoids per linear meter of hedge); all three haplotypes were released at a fourth planting beginning midway through the study (over all releases, an average combined total of 202 parasitoids per linear meter of hedge). Asian citrus psyllid populations were present year-round at each planting, often at large levels. Such plantings may pose risk to commercial citrus as Asian citrus psyllid reservoirs. Releases of the new haplotypes did not cause any measurable reduction in Asian citrus psyllid population levels during the study, and ironically percentage parasitism was generally highest at a planting where no releases were made. Higher release rates might have been more effective. The probability is discussed that repetitive pruning of orange jasmine reduced the full potential of T. radiata against Asian citrus psyllid in this study. Published by Oxford University Press on behalf of Entomological Society of America 2015. This work is written by US Government employees and is in the public domain in the US.

Risk Associated with the Release of Wolbachia-Infected Aedes aegypti Mosquitoes into the Environment in an Effort to Control Dengue.

PubMed

Murray, Justine V; Jansen, Cassie C; De Barro, Paul

2016-01-01

In an effort to eliminate dengue, a successful technology was developed with the stable introduction of the obligate intracellular bacteria Wolbachia pipientis into the mosquito Aedes aegypti to reduce its ability to transmit dengue fever due to life shortening and inhibition of viral replication effects. An analysis of risk was required before considering release of the modified mosquito into the environment. Expert knowledge and a risk assessment framework were used to identify risk associated with the release of the modified mosquito. Individual and group expert elicitation was performed to identify potential hazards. A Bayesian network (BN) was developed to capture the relationship between hazards and the likelihood of events occurring. Risk was calculated from the expert likelihood estimates populating the BN and the consequence estimates elicited from experts. The risk model for "Don't Achieve Release" provided an estimated 46% likelihood that the release would not occur by a nominated time but generated an overall risk rating of very low. The ability to obtain compliance had the greatest influence on the likelihood of release occurring. The risk model for "Cause More Harm" provided a 12.5% likelihood that more harm would result from the release, but the overall risk was considered negligible. The efficacy of mosquito management had the most influence, with the perception that the threat of dengue fever had been eliminated, resulting in less household mosquito control, and was scored as the highest ranked individual hazard (albeit low risk). The risk analysis was designed to incorporate the interacting complexity of hazards that may affect the release of the technology into the environment. The risk analysis was a small, but important, implementation phase in the success of this innovative research introducing a new technology to combat dengue transmission in the environment.

Chromosome behavior of heat shock induced triploid in Fenneropenaeus chinensis

NASA Astrophysics Data System (ADS)

Zhang, Xiaojun; Li, Fuhua; Xiang, Jianhai

2003-09-01

Triploidy was induced in Chinese shrimp Fenneropenaeus chinensis by 30±0.5°C heat shock treatment (initiated at 20 min after fertilization) for 10 min to inhibit the release of PB2 at 18.0°C. The highest triploid rate obtained was 84.5% in nauplius stage. The effect of heat shock treatment on meiosis and cleavage of eggs was investigated in this work aimed to establish efficient procedures for triploid induction and to gain understanding of the mechanism of triploid production. Three pronuclei that could be observed in the treated eggs under fluorescence microscope developed into triploid embryos. Some abnormal chromosome behavior was observed in heat shocked eggs.

State variation in rates of cesarean and VBAC delivery: 1989 and 1993.

PubMed

Clarke, S C; Taffel, S M

1996-01-01

There is wide variation among states in rates of cesarean and vaginal births after cesarean (VBAC) deliveries. In general, states in the South have the highest cesarean rates, states in the West have the lowest, and states in the Northeast and Midwest are intermediate. Louisiana had the highest overall rate in 1993 (27.7 per 100 births) while Alaska had the lowest rate (15.2). The majority of states had declines in their cesarean rate between 1989 and 1993. Patterns in primary cesarean rates are similar to those of the overall rate-states in the South generally have the highest rates while states in the West have the lowest rates. Primary cesarean rates ranged between a high of 19.6 in Louisiana to a low of 10.6 in Wisconsin. In general, states with low cesarean rates have among the highest rates of VBAC delivery. Alaska had the highest VBAC rate (40.0), which was almost quadruple the rate of Louisiana (11.2), the state with the lowest rate. Most states had substantial increases in VBAC rates between 1989 and 1993. When examining cesarean rates by maternal age and birth order, states with the highest overall rates also have among the highest age/birth order-specific rates. Cesarean rates were lowest for mothers under 25 years of age having a second or higher order birth in Alaska, 10.4, and highest for mothers 35 years of age or over having a first birth in Mississippi, 51.3. Standardized cesarean rates which were adjusted for differences between states in maternal age and birth order distributions did not diminish the variation among areas.

Spatially resolved heat release rate measurements in turbulent premixed flames

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ayoola, B.O.; Kaminski, C.F.; Balachandran, R.

Heat release rate is a fundamental property of great importance for the theoretical and experimental elucidation of unsteady flame behaviors such as combustion noise, combustion instabilities, and pulsed combustion. Investigations of such thermoacoustic interactions require a reliable indicator of heat release rate capable of resolving spatial structures in turbulent flames. Traditionally, heat release rate has been estimated via OH or CH radical chemiluminescence; however, chemiluminescence suffers from being a line-of-sight technique with limited capability for resolving small-scale structures. In this paper, we report spatially resolved two-dimensional measurements of a quantity closely related to heat release rate. The diagnostic technique usesmore » simultaneous OH and CH{sub 2}O planar laser-induced fluorescence (PLIF), and the pixel-by-pixel product of the OH and CH{sub 2}O PLIF signals has previously been shown to correlate well with local heat release rates. Results from this diagnostic technique, which we refer to as heat release rate imaging (HR imaging), are compared with traditional OH chemiluminescence measurements in several flames. Studies were performed in lean premixed ethylene flames stabilized between opposed jets and with a bluff body. Correlations between bulk strain rates and local heat release rates were obtained and the effects of curvature on heat release rate were investigated. The results show that the heat release rate tends to increase with increasing negative curvature for the flames investigated for which Lewis numbers are greater than unity. This correlation becomes more pronounced as the flame gets closer to global extinction.« less

Effect of binary organic solvents together with emulsifier on particle size and in vitro behavior of paclitaxel-encapsulated polymeric lipid nanoparticles.

PubMed

Qin, Shuzhi; Sun, Xiangshi; Li, Feng; Yu, Kongtong; Zhou, Yulin; Liu, Na; Zhao, Chengguo; Teng, Lesheng; Li, Youxin

2017-12-21

Biodegradable nanoparticles with diameters between 100 nm and 500 nm are of great interest in the contexts of targeted delivery. The present work provides a review concerning the effect of binary organic solvents together with emulsifier on particle size as well as the influence of particle size on the in vitro drug release and uptake behavior. The polymeric lipid nanoparticles (PLNs) with different particle sizes were prepared by using binary solvent dispersion method. Various formulation parameters such as binary organic solvent composition and emulsifier types were evaluated on the basis of their effects on particle size and size distribution. PLNs had a strong dependency on the surface tension, intrinsic viscosity and volatilization rate of binary organic solvents and the hydrophilicity/hydrophobicity of emulsifiers. Acetone-methanol system together with pluronic F68 as emulsifier was proved to obtain the smallest particle size. Then the PLNs with different particle sizes were used to investigate how particle size at nanoscale affects interacted with tumor cells. As particle size got smaller, cellular uptake increased in tumor cells and PLNs with particle size of ~120 nm had the highest cellular uptake and fastest release rate. The paclitaxel (PTX)-loaded PLNs showed a size-dependent inhibition of tumor cell growth, which was commonly influenced by cellular uptake and PTX release. The PLNs would provide a useful means to further elucidate roles of particle size on delivery system of hydrophobic drugs. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Bioavailability of modified-release methylphenidate: influence of high-fat breakfast when administered intact and when capsule content sprinkled on applesauce.

PubMed

Lee, Lucy; Kepple, Joanne; Wang, Yibin; Freestone, Stephen; Bakhtiar, Ray; Wang, Yanfeng; Hossain, Mohammad

2003-09-01

Ritalin, an immediate release form of racemic methylphenidate hydrochloride, has been available in the USA since 1955 and is used for the treatment of ADHD. The objective of this study was to evaluate the pharmacokinetics of modified-release methylphenidate (highest single dose), Ritalin LA, when administered under fasting condition, with a high-fat breakfast, and when sprinkled on applesauce in healthy adult subjects. Blood samples were drawn for 24 h following a 40 mg oral administration. Most subjects appeared to produce a bimodal methylphenidate plasma concentration profile. In all three treatment groups, methylphenidate was rapidly absorbed with an initial average t(max(0-4)) of 1.3-2.4 h and an average peak plasma concentration [C(max(abs))] of 14.4-15.2 ng/ml. On average, both the rate [C(max(abs)) and t(max(abs))] and the extent of absorption (AUC(0- infinity)) of methylphenidate were similar when the capsule was given with a high fat breakfast and when the capsule contents were sprinkled onto applesauce, compared with the fasting state. No dose dumping was observed when the capsule was given with a high fat breakfast or when sprinkled onto applesauce. The dose was safe and generally well tolerated. Coadministration of a single oral dose of 40 mg methylphenidate capsule whether administered intact with a high-fat breakfast or sprinkled on applesauce did not affect the overall rate or extent of absorption of methylphenidate compared with the fasted condition. Copyright 2003 John Wiley & Sons, Ltd.

Gauging interest of the general public in laser-assisted in situ keratomileusis eye surgery.

PubMed

Stein, Joshua D; Childers, David M; Nan, Bin; Mian, Shahzad I

2013-07-01

To assess interest among members of the general public in laser-assisted in situ keratomileusis (LASIK) surgery and how levels of interest in this procedure have changed over time in the United States and other countries. Using the Google Trends Web site, we determined the weekly frequency of queries involving the term "LASIK" from January 1, 2007, through January 1, 2011, in the United States, United Kingdom, Canada, and India. We fit separate regression models for each of the countries to assess whether residents of these countries differed in their querying rates on specific dates and over time. Similar analyses were performed to compare 4 US states. Additional regression models compared general public interest in LASIK surgery before and after the release of a 2008 Food and Drug Administration report describing complaints associated with this procedure. During 2007 to 2011, the Google query rate for "LASIK" was highest among persons residing in India, followed by the United Kingdom, Canada, and the United States. During this time period, the query rate declined by 40% in the United States, 24% in India, and 22% in the United Kingdom, and it increased by 8% in Canada. In all 4 of the US states examined, the query rate declined-by 52% in Florida, 56% in New York, 54% in Texas, and 42% in California. Interest in LASIK declined further among US citizens after the Food and Drug Administration report release. Interest among the general public in LASIK surgery has been waning in recent years.

pH responsive cross-linked polymeric matrices based on natural polymers: effect of process variables on swelling characterization and drug delivery properties.

PubMed

Naeem, Fahad; Khan, Samiullah; Jalil, Aamir; Ranjha, Nazar Muhammad; Riaz, Amina; Haider, Malik Salman; Sarwar, Shoaib; Saher, Fareha; Afzal, Samrin

2017-01-01

Introduction: The current work was aimed to design and synthesize novel crosslinked pH-sensitive gelatin/pectin (Ge/Pec) hydrogels using different polymeric ratios and to explore the effect of polymers and degree of crosslinking on dynamic, equilibrium swelling and in vitro release behavior of the model drug (Mannitol). Methods: The Ge/Pec based hydrogels were prepared using glutaraldehyde as the crosslinker. Various structural parameters that affect their release behavior were determined, including swelling study, porosity, sol-gel analysis, average molecular weight between crosslinks (Mc), volume fraction of polymer (V2,s), solvent interaction parameter (χ) and diffusion coefficient. The synthesized hydrogels were subjected to various characterization tools like Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and DSC differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). Results: The hydrogels show highest water uptake and release at lower pH values. The FTIR spectra showed an interaction between Ge and Pec, and the drug-loaded samples also showed the drug-related peaks, indicating proper loading of the drug. DSC and TGA studies confirmed the thermal stability of hydrogel samples, while SEM showed the porous nature of hydrogels. The drug release followed non-Fickian diffusion or anomalous mechanism. Conclusion: Aforementioned characterizations reveal the successful formation of copolymer hydrogels. The pH-sensitive swelling ability and drug release behavior suggest that the rate of polymer chain relaxation and drug diffusion from these hydrogels are comparable which also predicts their possible use for site-specific drug delivery.

pH responsive cross-linked polymeric matrices based on natural polymers: effect of process variables on swelling characterization and drug delivery properties

PubMed Central

Naeem, Fahad; Khan, Samiullah; Jalil, Aamir; Ranjha, Nazar Muhammad; Riaz, Amina; Haider, Malik Salman; Sarwar, Shoaib; Saher, Fareha; Afzal, Samrin

2017-01-01

Introduction: The current work was aimed to design and synthesize novel crosslinked pH-sensitive gelatin/pectin (Ge/Pec) hydrogels using different polymeric ratios and to explore the effect of polymers and degree of crosslinking on dynamic, equilibrium swelling and in vitro release behavior of the model drug (Mannitol). Methods: The Ge/Pec based hydrogels were prepared using glutaraldehyde as the crosslinker. Various structural parameters that affect their release behavior were determined, including swelling study, porosity, sol-gel analysis, average molecular weight between crosslinks (Mc), volume fraction of polymer (V2,s), solvent interaction parameter (χ) and diffusion coefficient. The synthesized hydrogels were subjected to various characterization tools like Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and DSC differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). Results:The hydrogels show highest water uptake and release at lower pH values. The FTIR spectra showed an interaction between Ge and Pec, and the drug-loaded samples also showed the drug-related peaks, indicating proper loading of the drug. DSC and TGA studies confirmed the thermal stability of hydrogel samples, while SEM showed the porous nature of hydrogels. The drug release followed non-Fickian diffusion or anomalous mechanism. Conclusion: Aforementioned characterizations reveal the successful formation of copolymer hydrogels. The pH-sensitive swelling ability and drug release behavior suggest that the rate of polymer chain relaxation and drug diffusion from these hydrogels are comparable which also predicts their possible use for site-specific drug delivery. PMID:29159145

Fission-gas release from uranium nitride at high fission rate density

NASA Technical Reports Server (NTRS)

Weinstein, M. B.; Kirchgessner, T. A.; Tambling, T. N.

1973-01-01

A sweep gas facility has been used to measure the release rates of radioactive fission gases from small UN specimens irradiated to 8-percent burnup at high fission-rate densities. The measured release rates have been correlated with an equation whose terms correspond to direct recoil release, fission-enhanced diffusion, and atomic diffusion (a function of temperature). Release rates were found to increase linearly with burnups between 1.5 and 8 percent. Pore migration was observed after operation at 1550 K to over 6 percent burnup.

Optimization of outgassing bake-out temperatures and duration of space systems

NASA Technical Reports Server (NTRS)

Scialdone, J. J.

1986-01-01

Satellite components, e.g., solar panels, were subjected to bake-out tests to model outgassing characteristics and to identify methods for minimizing the bake-out time. Bake-out removes gases and particulates that are trapped at the surfaces of components during manufacture, storage, transit and handling. The tests covered temperatures from 45-85 C for up to 200 hr. Measurements of the mass loss rates were used to model the process as a function of the temperature, time and mass. Data sampling with a quartz crystal microbalance was found to be an effective means for ascertaining the mass loss rate and the activation energy of the release. The tests showed that the duration of the bake-out depends on the amount of material which must be removed and the type of outgassing which occurs. Materials which are resistant to high temperatures can be baked at the highest feasible temperatures to accelerate the outgassing process.

Leukocyte- and platelet-rich fibrin (L-PRF) for long-term delivery of growth factor in rotator cuff repair: review, preliminary results and future directions.

PubMed

Zumstein, Matthias A; Berger, Simon; Schober, Martin; Boileau, Pascal; Nyffeler, Richard W; Horn, Michael; Dahinden, Clemens A

2012-06-01

Surgical repair of the rotator cuff repair is one of the most common procedures in orthopedic surgery. Despite it being the focus of much research, the physiological tendon-bone insertion is not recreated following repair and there is an anatomic non-healing rate of up to 94%. During the healing phase, several growth factors are upregulated that induce cellular proliferation and matrix deposition. Subsequently, this provisional matrix is replaced by the definitive matrix. Leukocyte- and platelet-rich fibrin (L-PRF) contain growth factors and has a stable dense fibrin matrix. Therefore, use of LPRF in rotator cuff repair is theoretically attractive. The aim of the present study was to determine 1) the optimal protocol to achieve the highest leukocyte content; 2) whether L-PRF releases growth factors in a sustained manner over 28 days; 3) whether standard/gelatinous or dry/compressed matrix preparation methods result in higher growth factor concentrations. 1) The standard L-PRF centrifugation protocol with 400 x g showed the highest concentration of platelets and leukocytes. 2) The L-PRF clots cultured in medium showed a continuous slow release with an increase in the absolute release of growth factors TGF-β1, VEGF and MPO in the first 7 days, and for IGF1, PDGF-AB and platelet activity (PF4=CXCL4) in the first 8 hours, followed by a decrease to close to zero at 28 days. Significantly higher levels of growth factor were expressed relative to the control values of normal blood at each culture time point. 3) Except for MPO and the TGFβ-1, there was always a tendency towards higher release of growth factors (i.e., CXCL4, IGF-1, PDGF-AB, and VEGF) in the standard/gelatinous- compared to the dry/compressed group. L-PRF in its optimal standard/gelatinous-type matrix can store and deliver locally specific healing growth factors for up to 28 days and may be a useful adjunct in rotator cuff repair.

Melting mountains of Appalachia: exceptionally high weathering rates in mined watersheds

NASA Astrophysics Data System (ADS)

Ross, M. R.; Nippgen, F.; Hassett, B.; McGlynn, B. L.; Bernhardt, E. S.

2016-12-01

Mountaintop mining operations excavate ridges as deep as 200 m and bury adjacent valleys and streams beneath fractured bedrock and coal residues. Post-mining, landscapes have lower slopes, greatly increased water storage potential, and an abundance of acid-generating pyrite, which is intentionally mixed with neutralizing calcareous bedrock. Together these design features of mountaintop mined lands create ideal conditions for long water residence times and rapid weathering rates, leading to widely documented and substantial increases in streamwater ion concentrations. To date, these concentration changes have not been linked to rates of watershed scale element flux. In a paired catchment study, we documented a 4,000% increase in the export of total dissolved solids from a mined watershed, and estimate that pyrite and carbonate weathering in reclaimed mines can export 9,000 kg ha-1 y-1 of dissolved rock to receiving streams. Such high rates of element flux after a disturbance are not only much higher than other watershed disturbances, but are among the highest rates of weathering ever reported globally. Sulfuric acid weathering of carbonate rock drives these patterns of chemical erosion. This strong acid weathering changes Appalachian geology from a slight net geologic CO2 sink-sequestering 800-1,500 kg CO2 km-2 yr-1 through carbonic acid weathering of carbonates-to a substantial net geologic source of CO2, releasing 170,000 kg CO2 km-2 yr-1. Over the more than 4,000 km2 area of Central Appalachia that has undergone mountaintop mining, this rapid weathering represents 4 million tons of dissolved rock being delivered to the streams of West Virginia, potentially releasing 680,000 tons of CO2 in the process.

Snake River Sockeye Salmon Captive Broodstock Program Research Elements : 2007 Annual Project Progess Report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peterson, Mike; Plaster, Kurtis; Redfield, Laura

2008-12-17

On November 20, 1991, the National Oceanic Atmospheric Administration listed Snake River sockeye salmon Oncorhynchus nerka as endangered under the Endangered Species Act of 1973. In 1991, the Shoshone-Bannock Tribes (SBT) and Idaho Department of Fish and Game (IDFG) initiated the Snake River Sockeye Salmon Captive Broodstock Program to conserve and rebuild populations in Idaho. Restoration efforts are focused on Redfish, Pettit, and Alturas lakes within the Sawtooth Valley. The first release of hatchery-produced adults occurred in 1993. The first release of juvenile sockeye salmon from the captive broodstock program occurred in 1994. In 1999, the first anadromous adult returnsmore » from the captive broodstock program were recorded when six jacks and one jill were captured at the IDFG Sawtooth Fish Hatchery. In 2007, progeny from the captive broodstock program were released using four strategies: (1) eyed-eggs were planted in Pettit Lake in November; (2) age-0 presmolts were released to Alturas, Pettit, and Redfish lakes in October; (3) age-1 smolts were released into Redfish Lake Creek and the upper Salmon River in May; and (4) hatchery-produced adult sockeye salmon were released to Redfish Lake for volitional spawning in September. Oncorhynchus nerka population monitoring was conducted on Redfish, Alturas, and Pettit lakes using a midwater trawl in September 2007. Population abundances were estimated at 73,702 fish for Redfish Lake, 124,073 fish for Alturas Lake, and 14,746 fish for Pettit Lake. Angler surveys were conducted from May 26 through August 7, 2007 on Redfish Lake to estimate kokanee harvest. On Redfish Lake, we interviewed 102 anglers and estimated that 56 kokanee were harvested. The calculated kokanee catch rate was 0.03 fish/hour for each kokanee kept. The juvenile out-migrant trap on Redfish Lake Creek was operated from April 14 to June 13, 2007. We estimated that 5,280 natural origin and 14,256 hatchery origin sockeye salmon smolts out-migrated from Redfish Lake in 2007. The hatchery origin component originated from a 2006 fall presmolt direct-release. The juvenile out-migrant traps on Alturas Lake Creek and Pettit Lake Creek were operated by the SBT from April 19 to May 23, 2007 and April 18 to May 29, 2007, respectively. The SBT estimated 1,749 natural origin and 4,695 hatchery origin sockeye salmon smolts out-migrated from Pettit Lake and estimated 8,994 natural origin and 6,897 hatchery origin sockeye salmon smolts out-migrated from Alturas Lake in 2007. The hatchery origin component of sockeye salmon out-migrants originated from fall presmolt direct-releases made to Pettit and Alturas lakes in 2006. In 2007, the Stanley Basin Sockeye Technical Oversight Committee (SBSTOC) chose to have all Snake River sockeye salmon juveniles (tagged and untagged) transported due to potential enhanced survival. Therefore, mainstem survival evaluations were only conducted to Lower Granite Dam. Unique PIT tag interrogations from Sawtooth Valley juvenile out-migrant traps to Lower Granite Dam were utilized to estimate survival rates for out-migrating sockeye salmon smolts. Survival rate comparisons were made between smolts originating from Redfish, Alturas, and Pettit lakes and the various release strategies. Alturas Lake hatchery origin smolts tagged at the out-migrant trap recorded the highest survival rate of 78.0%. In 2007, 494 hatchery origin adult sockeye salmon were released to Redfish Lake for natural spawning. We observed 195 areas of excavation in the lake from spawning events. This was the highest number of redds observed in Redfish Lake since the program was initiated. Suspected redds were approximately 3 m x 3 m in size and were constructed by multiple pairs of adults. To monitor the predator population found within the lakes, we monitored bull trout spawning in Fishhook Creek, a tributary to Redfish Lake; and in Alpine Creek, a tributary to Alturas Lake. This represented the tenth consecutive year that the index reaches have been surveyed on these two streams. Adult counts (41 adults) and redd counts (22 redds) in Fishhook Creek increased compared to counts conducted since monitoring began in 1998. Beginning in 2007, we also surveyed an additional trend site in Fishhook Creek resulting in observing 43 adult bull trout and 30 additional redds. Bull trout numbers (13 adults) and the number of redds observed (18 redds) have gradually increased in Alpine Creek compared to counts from initial monitoring.« less

Final disposition and quality auditing of the rehabilitation process in wild raptors admitted to a Wildlife Rehabilitation Centre in Catalonia, Spain, during a twelve year period (1995-2007).

PubMed

Molina-López, Rafael A; Casal, Jordi; Darwich, Laila

2013-01-01

Variability in reporting and classification methods in previous published data of the final dispositions in the rehabilitation of wild raptors makes use of this data limited in trying to audit the quality of the rehabilitation process. Crude as well as stratified disposition rates are needed if quality auditing of the rehabilitation process is to be adequately performed. Final dispositions of 6221 hospitalized wild raptors admitted at a wildlife rehabilitation centre (WRC) of Catalonia during 1995-2007 were analyzed. These dispositions were calculated as the euthanasia (Er), unassisted mortality (Mr), release (Rr) and captivity rates (Cr)., time to death (Td) for dead and euthanized raptors, and length of stay for released (Tr) raptors was estimated. Stratified analyses by main causes of admission and clinical signs were performed. THE DISPOSITION FOR THE TOTAL POPULATION WERE: Er = 30.6%, Mr = 19.1%, Rr = 47.2%, and Cr = 3%. By main causes of admission, Er was higher in the trauma category (34.2%), whereas Mr was found similar between trauma (37.4%) and non-trauma categories (34.8%). The highest Rr was observed for the orphaned group (77.9%). Furthermore, Cr was low in all the categories (<4%). By clinical signs, the highest Er was found in animals suffering musculoskeletal (37.9%) or skin (32.3%) lesions; Mr was high in infectious/parasitic diseases (66.7%) and in case of neurological symptoms (64.5%). The euthanized birds had a median Td = 1 day (P10 = 0-P90 = 59) for both trauma and non-trauma categories, and Td = 36 days for the orphaned young group (P10 = 0; P90 = 596). The median Td in the unassisted dead birds was 2 days for all the categories (P10 = 0-P90 = 31). Finally, the median Tr in the centre was variable among categories. Reporting of final dispositions in wildlife rehabilitation should include the crude and stratified rates (Er, Mr, Rr, and Cr), by causes and clinical presentation, as well as Td and Tr, to allow meaningful auditing of the rehabilitation process quality.

Occurrence and transport of tetracycline, sulfonamide, quinolone, and macrolide antibiotics in the Haihe River Basin, China.

PubMed

Luo, Yi; Xu, Lin; Rysz, Michal; Wang, Yuqiu; Zhang, Hao; Alvarez, Pedro J J

2011-03-01

The occurrence and transport of 12 antibiotics (from the tetracycline, sulfonamide, quinolone, and macrolide families) was studied in a 72-km stretch of the Haihe River, China, and in six of its tributaries. Aqueous and sediment samples were analyzed by HPLC-MS/MS. Sulfonamides were detected at the highest concentrations (24-385 ng/L) and highest frequencies (76-100%). Eight of the 12 antibiotics likely originated from veterinary applications in swine farms and fishponds, and concentrations at these sources (0.12-47 μg/L) were 1-2 orders of magnitude higher than in the effluent of local wastewater treatment plants. Sulfachloropyridazine (SCP) was detected in all swine farm and fishpond samples (maximum concentration 47 μg/L), which suggests its potential usefulness to indicate livestock source pollution in the Haihe River basin. Hydrological and chemical factors that may influence antibiotic distribution in the Haihe River were considered by multiple regression analysis. River flow rate exerted the most significant effect on the first-order attenuation coefficient (K) for sulfonamides, quinolones, and macrolides, with higher flow rates resulting in higher K, probably due to dilution. For tetracyclines, sediment total organic matter and cation exchange capacity exerted a greater impact on K than flow rate, indicating that adsorption to sediments plays an important role in attenuating tetracycline migration. Overall, the predominance of sulfonamides in the Haihe River underscores the need to consider regulating their veterinary use and improving the management and treatment of associated releases.

Seasonal occurrence and degradation of 2-methylisoborneol in water supply reservoirs.

PubMed

Westerhoff, Paul; Rodriguez-Hernandez, M; Baker, Larry; Sommerfeld, Milton

2005-12-01

Methylisoborneol (MIB) and geosmin are cyanobacterial metabolites that occur at nanograms per liter levels in surface water supplies and are responsible for many taste and odor complaints about the aesthetics of drinking water. This study evaluated three water supply reservoirs with bottom-release (hypolimnion) outlet structures in Arizona. MIB concentrations were always higher than geosmin concentrations, but both followed similar seasonal trends. MIB concentrations increased from spring to late summer, and stratified vertically with depth in the water column; the highest concentrations were always in the upper 10 m of the water column. Thermal destratification in the autumn increased MIB concentrations released from the outlet of reservoirs and impacted downstream utilities for several months. By winter of each year MIB concentrations were non-detectable. Mass balance analyses on MIB indicated that in-reservoir reactions were more important in changing MIB concentrations than conservative hydraulic "flushing" of the reservoir. Maximum net loss rates for MIB in the field (R(F,max)) were on the order of 0.23-1.7 ng/L-day, and biodegradation appeared more important than volatilization, photolysis or adsorption. Using lake water in laboratory experiments, bacterial biodegradation rates (R(L)) ranged from 0.5-1 ng/L-day and were comparable to R(F,max) values. Based upon these rates, MIB concentrations in a reservoir would decrease by approximately 30 ng/L over a period of 1 month. This was the magnitude change in MIB concentrations commonly observed after autumn thermal destratification of the reservoirs.

Bioleaching mechanism of Co and Li from spent lithium-ion battery by the mixed culture of acidophilic sulfur-oxidizing and iron-oxidizing bacteria.

PubMed

Xin, Baoping; Zhang, Di; Zhang, Xian; Xia, Yunting; Wu, Feng; Chen, Shi; Li, Li

2009-12-01

The bioleaching mechanism of Co and Li from spent lithium-ion batteries by mixed culture of sulfur-oxidizing and iron-oxidizing bacteria was investigated. It was found that the highest release of Li occurred at the lowest pH of 1.54 with elemental sulfur as an energy source, the lowest occurred at the highest pH of 1.69 with FeS(2). In contrast, the highest release of Co occurred at higher pH and varied ORP with S + FeS(2), the lowest occurred at almost unchanged ORP with S. It is suggested that acid dissolution is the main mechanism for Li bioleaching independent of energy matters types, however, apart from acid dissolution, Fe(2+) catalyzed reduction takes part in the bioleaching process as well. Co(2+) was released by acid dissolution after insoluble Co(3+) was reduced into soluble Co(2+) by Fe(2+) in both FeS(2) and FeS(2) + S systems. The proposed bioleaching mechanism mentioned above was confirmed by the further results obtained from the experiments of bioprocess-stimulated chemical leaching and from the changes in structure and component of bioleaching residues characterized by XPS, SEM and EDX.

Metal release from stainless steel particles in vitro-influence of particle size.

PubMed

Midander, K; Pan, J; Wallinder, I Odnevall; Leygraf, C

2007-01-01

Human inhalation of airborne metallic particles is important for health risk assessment. To study interactions between metallic particles and the human body, metal release measurements of stainless steel powder particles were performed in two synthetic biological media simulating lung-like environments. Particle size and media strongly influence the metal release process. The release rate of Fe is enhanced compared with Cr and Ni. In artificial lysosomal fluid (ALF, pH 4.5), the accumulated amounts of released metal per particle loading increase drastically with decreasing particle size. The release rate of Fe per unit surface area increases with decreasing particle size. Compared with massive sheet metal, fine powder particles (<4 microm) show similar release rates of Cr and Ni, but a higher release rate of Fe. Release rates in Gamble's solution (pH 7.4), for all powders investigated, are significantly lower compared to ALF. No clear trend is seen related to particle size in Gamble's solution.

Mechanistic approach for nitride fuel evolution and fission product release under irradiation

NASA Astrophysics Data System (ADS)

Dolgodvorov, A. P.; Ozrin, V. D.

2017-01-01

A model for describing uranium-plutonium mixed nitride fuel pellet burning was developed. Except fission products generating, the model includes impurities of oxygen and carbon. Nitrogen behaviour in nitride fuel was analysed and the nitrogen chemical potential in solid solution with uranium-plutonium nitride was constructed. The chemical program module was tested with the help of thermodynamic equilibrium phase distribution calculation. Results were compared with analogous data in literature, quite good agreement was achieved, especially for uranium sesquinitride, metallic species and some oxides. Calculation of a process of nitride fuel burning was also conducted. Used mechanistic approaches for fission product evolution give the opportunity to find fission gas release fractions and also volumes of intergranular secondary phases. Calculations present that the most massive secondary phases are the oxide and metallic phases. Oxide phase contain approximately 1 % wt of substance over all time of burning with slightly increasing of content. Metallic phase has considerable rising of mass and by the last stage of burning it contains about 0.6 % wt of substance. Intermetallic phase has less increasing rate than metallic phase and include from 0.1 to 0.2 % wt over all time of burning. The highest element fractions of released gaseous fission products correspond to caesium and iodide.

Factors influencing lead and iron release from some Egyptian drinking water pipes.

PubMed

Lasheen, M R; Sharaby, C M; El-Kholy, N G; Elsherif, I Y; El-Wakeel, S T

2008-12-30

The major objective of this study is to assess the effect of stagnation time, pipe age, pipes material and water quality parameters such as pH, alkalinity and chloride to sulfate mass ratio on lead and iron release from different types of water pipes used in Egypt namely polyvinyl chloride (PVC), polypropylene (PP) and galvanized iron (GI), by using fill and dump method. Low pH increased lead and iron release from pipes. Lead and iron release decreased as pH and alkalinity increased. Lead and iron release increased with increasing chloride to sulfate mass ratio in all pipes. EDTA was used as an example of natural organic matter which may be influence metals release. It is found that lead and iron release increased then this release decreased with time. In general, GI pipes showed to be the most effected by water quality parameters tested and the highest iron release. PVC pipes are the most lead releasing pipes while PP pipes are the least releasing.

Reversible covalent binding of neratinib to human serum albumin in vitro.

PubMed

Chandrasekaran, Appavu; Shen, Li; Lockhead, Susan; Oganesian, Aram; Wang, Jianyao; Scatina, JoAnn

2010-12-01

Neratinib (HKI-272), an irreversible inhibitor of Her 2 tyrosine kinase, is currently in development as an alternative for first and second line therapy in metastatic breast cancer patients who overexpress Her 2. Following incubation of [(14)C]neratinib in control human plasma at 37°C for 6 hours, about 60% to 70% of the radioactivity was not extractable, due to covalent binding to albumin. In this study, factors that could potentially affect the covalent binding of neratinib to plasma proteins, specifically to albumin were investigated. When [(14)C]neratinib was incubated at 10 μg/mL in human serum albumin (HSA) or control human plasma, the percent binding increased with time; the highest percentages of binding (46 and 67%, respectively) were observed at 6 hours, the longest duration of incubation examined. Binding increased with increasing temperature; the highest percentages of binding to HSA or human plasma (59 and 78%) were observed at 45°C, the highest temperature tested. The binding also increased with increasing pH of incubation; the highest percentages of binding (56 and 65%) were observed at pH 8.5, the highest pH value tested. The percentages of binding were similar (53% to 57%) when a wide range of concentrations of [(14)C]neratinib (50 ng/mL to 10 μg/mL) were incubated with human plasma at 37°C for 6 hours, indicating that the binding was independent of the substrate concentration, especially in the therapeutic range (50 to 200 ng/mL). When human plasma proteins containing covalently bound [(14)C]neratinb were suspended in a 10 fold volume of phosphate buffer at pH 4.0, 6.0, 7.4, and 8.5, and further incubated at 37°C for ~ 16 hours, about 45%, 44%, 32%, and 12% of the total radioactivity, respectively, was released as unchanged [(14)C]neratinib, indicating that the binding is reversible in nature, with more released at pH 7.4 and below. In conclusion, the covalent binding of neratinib to serum albumin is pH, time and temperature dependent, but not substrate concentration dependent, especially in the therapeutic range. Acidification and incubation of human plasma proteins that contained covalently bound [(14)C]neratinib leads to the release of the drug, indicating that the binding is reversible in nature. It is reasonable to speculate that the release of neratinib from human serum albumin provides a transport system leading to release of neratinib in the more acidic environment of the tumor.

Soil carbon stocks in Sarawak, Malaysia.

PubMed

Padmanabhan, E; Eswaran, H; Reich, P F

2013-11-01

The relationship between greenhouse gas emission and climate change has led to research to identify and manage the natural sources and sinks of the gases. CO2, CH4, and N2O have an anthropic source and of these CO2 is the least effective in trapping long wave radiation. Soil carbon sequestration can best be described as a process of removing carbon dioxide from the atmosphere and relocating into soils in a form that is not readily released back into the atmosphere. The purpose of this study is to estimate carbon stocks available under current conditions in Sarawak, Malaysia. SOC estimates are made for a standard depth of 100 cm unless the soil by definition is less than this depth, as in the case of lithic subgroups. Among the mineral soils, Inceptisols tend to generally have the highest carbon contents (about 25 kg m(-2) m(-1)), while Oxisols and Ultisols rate second (about 10-15 kg m(-2) m(-1)). The Oxisols store a good amount of carbon because of an appreciable time-frame to sequester carbon and possibly lower decomposition rates for the organic carbon that is found at 1m depths. Wet soils such as peatlands tend to store significant amounts of carbon. The highest values estimated for such soils are about 114 kg m(-2) m(-1). Such appreciable amounts can also be found in the Aquepts. In conclusion, it is pertinent to recognize that degradation of the carbon pool, just like desertification, is a real process and that this irreversible process must be addressed immediately. Therefore, appropriate soil management practices should be instituted to sequester large masses of soil carbon on an annual basis. This knowledge can be used effectively to formulate strategies to prevent forest fires and clearing: two processes that can quickly release sequestered carbon to the atmosphere in an almost irreversible manner. Copyright © 2013 Elsevier B.V. All rights reserved.

The effect of platform switching on the levels of metal ion release from different implant–abutment couples

PubMed Central

Alrabeah, Ghada O; Knowles, Jonathan C; Petridis, Haralampos

2016-01-01

The improved peri-implant bone response demonstrated by platform switching may be the result of reduced amounts of metal ions released to the surrounding tissues. The aim of this study was to compare the levels of metal ions released from platform-matched and platform-switched implant–abutment couples as a result of accelerated corrosion. Thirty-six titanium alloy (Ti-6Al-4V) and cobalt–chrome alloy abutments were coupled with titanium cylinders forming either platform-switched or platform-matched groups (n=6). In addition, 18 unconnected samples served as controls. The specimens were subjected to accelerated corrosion by static immersion in 1% lactic acid for 1 week. The amount of metal ions ion of each test tube was measured using inductively coupled plasma mass spectrometry. Scanning electron microscope (SEM) images and energy dispersive spectroscopy X-ray analyses were performed pre- and post-immersion to assess corrosion at the interface. The platform-matched groups demonstrated higher ion release for vanadium, aluminium, cobalt, chrome, and molybdenum compared with the platform-switched groups (P<0.05). Titanium was the highest element to be released regardless of abutment size or connection (P<0.05). SEM images showed pitting corrosion prominent on the outer borders of the implant and abutment platform surfaces. In conclusion, implant–abutment couples underwent an active corrosion process resulting in metal ions release into the surrounding environment. The highest amount of metal ions released was recorded for the platform-matched groups, suggesting that platform-switching concept has a positive effect in reducing the levels of metal ion release from the implant–abutment couples. PMID:27357323

Levonorgestrel release rates over 5 years with the Liletta® 52-mg intrauterine system.

PubMed

Creinin, Mitchell D; Jansen, Rolf; Starr, Robert M; Gobburu, Joga; Gopalakrishnan, Mathangi; Olariu, Andrea

2016-10-01

To understand the potential duration of action for Liletta®, we conducted this study to estimate levonorgestrel (LNG) release rates over approximately 5½years of product use. Clinical sites in the U.S. Phase 3 study of Liletta collected the LNG intrauterine systems (IUSs) from women who discontinued the study. We randomly selected samples within 90-day intervals after discontinuation of IUS use through 900days (approximately 2.5years) and 180-day intervals for the remaining duration through 5.4years (1980days) to evaluate residual LNG content. We also performed an initial LNG content analysis using 10 randomly selected samples from a single lot. We calculated the average ex vivo release rate using the residual LNG content over the duration of the analysis. We analyzed 64 samples within 90-day intervals (range 6-10 samples per interval) through 900days and 36 samples within 180-day intervals (6 samples per interval) for the remaining duration. The initial content analysis averaged 52.0±1.8mg. We calculated an average initial release rate of 19.5mcg/day that decreased to 17.0, 14.8, 12.9, 11.3 and 9.8mcg/day after 1, 2, 3, 4 and 5years, respectively. The 5-year average release rate is 14.7mcg/day. The estimated initial LNG release rate and gradual decay of the estimated release rate are consistent with the target design and function of the product. The calculated LNG content and release rate curves support the continued evaluation of Liletta as a contraceptive for 5 or more years of use. Liletta LNG content and release rates are comparable to published data for another LNG 52-mg IUS. The release rate at 5years is more than double the published release rate at 3years with an LNG 13.5-mg IUS, suggesting continued efficacy of Liletta beyond 5years. Copyright © 2016 Elsevier Inc. All rights reserved.

Impact of Saccharomyces cerevisiae strains on traditional sparkling wines production.

PubMed

Di Gianvito, Paola; Perpetuini, Giorgia; Tittarelli, Fabrizia; Schirone, Maria; Arfelli, Giuseppe; Piva, Andrea; Patrignani, Francesca; Lanciotti, Rosalba; Olivastri, Lino; Suzzi, Giovanna; Tofalo, Rosanna

2018-07-01

Sparkling wine fermentation is a challenge for yeasts due to the hostile conditions. A phenotype sought in starters is flocculation, because it reduces riddling time. For this reason, six flocculent Saccharomyces cerevisiae wine strains with different flocculation degree and autolytic activity and two commercial strains were tested for traditional sparkling wine production in a winery. Yeast viability, free aminoacids and high molecular weight nitrogen release and physico-chemical composition of sparkling wines were evaluated. Moreover, strains were tested for their aromatic potential. Obtained data revealed that flocculent yeasts presented oenological performances (in terms of fermentation rate, maximum pressure reached, free aminoacids - AAN and high molecular weight nitrogen - HMWN release) similar to the commercial strains. All considered strains were able to complete fermentation and viable cells of all strains were detected in all sparkling wines produced even after 6 months. F6789 and F10471 strains showed slow fermentation kinetics reaching the maximum of pressure at 180 days. Regarding nitrogen compounds release, FI strain was characterized by the highest amount of AAN and HMWN released, followed by F6789. Strains showed a considerable diversification in terms of number and amount of aroma molecules produced and sparkling wines obtained with autochthonous flocculent strains presented a higher amount of alcohols and esters already after 3 months. Further studies are necessary to select starter strains to improve traditional sparkling wines production. Copyright © 2018 Elsevier Ltd. All rights reserved.

Development of Polyethylene Glycol and Hard Fat-Based Mucoadhesive Tablets Containing Various Types of Polyvinyl Alcohols as Mucoadhesive Polymers for Buccal Application.

PubMed

Ikeuchi-Takahashi, Yuri; Kobayashi, Ayaka; Onishi, Hiraku

2017-06-01

Topical drug application has the advantage of avoiding systemic side effects. We attempted to develop a long-acting matrix-type tablet containing indomethacin (IM) with low physical stimulus and potent mucoadhesive force to treat pain caused by oral aphtha. A mixture of polyethylene glycol (PEG) and hard fat was used as the tablet base. Ethylcellulose was added to the base in an attempt to control drug release. Tablets with PEG as a base were also prepared for comparison. Polyvinyl alcohols (PVAs) with various degrees of saponification were added to increase the mucoadhesive force. From the optical microscopic observations, formulations using PEG and hard fat exhibit PEG/hard fat dispersions caused by the stabilizing effects of PVA. Although the tablets using PEG and hard fat showed sufficient adhesiveness and sustained drug release, those using PEG as the base did not. Drug release was controlled by the amount of hard fat and the saponification degree of PVA. The drug release rate was most increased in a tablet containing PVA with an intermediate degree of saponification, PEG and hard fat. From differential scanning calorimetry and powder X-ray diffraction, IM was considered to exist in the molecular phase. From the results of buccal administration of tablets to rats, highest tissue concentrations were observed in the tablet containing PVA with the intermediate degree of saponification using PEG and hard fat, and the plasma concentrations were sufficiently low in comparison.

Pharmacokinetics and analgesic effect of ketorolac floating delivery system.

PubMed

Radwan, Mahasen A; Abou El Ela, Amal El Sayeh F; Hassan, Maha A; El-Maraghy, Dalia A

2015-05-01

The efficacy of ketorolac tromethamine (KT) floating alginate beads as a drug delivery system for better control of KT release was investigated. The formulation with the highest drug loading, entrapment efficiency, swelling, buoyancy, and in vitro release would be selected for further in vivo analgesic effect in the mice and pharmacokinetics study in rats compared to the tablet dosage form. KT floating alginate beads were prepared by extrusion congealing technique. KT in plasma samples was analyzed using a UPLC MS/MS assay. The percentage yield, drug loading and encapsulation efficiency were increased proportionally with the hydroxypropylmethyl cellulose (HPMC) polymer amount in the KT floating beads. A reverse relationship was observed between HPMC amount in the beads and the KT in vitro release rate. F3-floating beads were selected, due to its better in vitro results (continued floating for >8 h) than others. A longer analgesic effect was observed for F3 in fed mice as compared to the tablets. After F3 administration to rats, the Cmax (2.2 ± 0.3 µg/ml) was achieved at ∼2 h and the decline in KT concentration was slower. F3 showed a significant increase in the AUC (1.89 fold) in rats as compared to the tablets. KT was successfully formulated as floating beads with prolonged in vitro release extended to a better in vivo characteristic with higher bioavailability in rats. KT in floating beads shows a superior analgesic effect over tablets, especially in fed mice.

Phase composition of lipoprotein SM/cholesterol/PtdCho affects FA specificity of sPLA2s.

PubMed

Kuksis, Arnis; Pruzanski, Waldemar

2008-10-01

We have previously reported preferential release of polyunsaturated FAs during hydrolysis of lipoprotein phosphatidylcholine (PtdCho) by group X secretory phospholipase A2 (sPLA2) and preferential release of oligounsaturated FAs during hydrolysis of lipoprotein PtdCho by group V sPLA2, but the mechanism of this selectivity has remained unknown. We now show that the rate and specificity of hydrolysis are affected by relative increases in endogenous SM and free cholesterol (FC) during the lipase digestion. The highest preference for arachidonate release from LDL and HDL by group X sPLA2 was observed for residual SM/PtdCho molar ratio of 1.2 and 0.4, compared with the respective starting ratios of 0.4 and 0.2, as measured by liquid chromatography/electrospray ionization-mass spectrometry. Group V sPLA2 showed preferential release of linoleate from LDL and HDL at SM/PtdCho ratio 1.5 and 0.6, respectively. We have attributed the change in FA specificity to segregation of molecular species of PtdCho and of sPLA2s between disordered and ordered SM/FC/PtdCho lipid phases. The increases in SM and FC during digestion with group IIA sPLA2 were more limited, and a preferential hydrolysis of any FAs was not observed. The significance of SM and FC SM and FC accumulation during sPLA2 hydrolysis of lipoprotein PtdCho has been previously overlooked.

Development of an osmotic pump system for controlled delivery of diclofenac sodium.

PubMed

Emara, L H; Taha, N F; Badr, R M; Mursi, N M

2012-10-01

Based on an elementary osmotic pump, controlled release systems of diclofenac sodium (DS) were designed to deliver the drug in a zero-order release pattern. Osmotic pump tablets containing 100 mg DS were prepared and coated with either semipermeable (SPM) or microporous (PM) membranes. The tablet coats were composed of hydrophobic triacetin (TA) or hydrophilic polyethylene glycol 400 (PEG 400) incorporated in cellulose acetate (CA) solution, for SPM and PM, respectively. Variable tablet core compositions such as swelling polymers (PEO and HPMC) and osmotic agents (lactose, NaCl, and KCl) were studied. An optimized, sensitive and well controlled in vitro release design, based on the flow-through cell (FTC), was utilized to discriminate between preparations. The results revealed that the presence of PEG 400 in the coating membrane accelerated the drug release rate, while TA suppressed the release rate of DS. In the case of SPM, the amount of DS released was inversely proportional to the membrane thickness, where 5% (w/w) weight gain gave a higher DS release rate than 10% (w/w). Results of different tablet core compositions revealed that the release rate of DS decreased as PEO molecular weight increased. HPMC K15M showed the lowest DS release rate. The presence of lactose, KCl, or NaCl pronouncedly affected DS release rate depending on polymer type in the core. Scanning electron microscopy (SEM) confirmed formation of pores in the membrane that accounts for faster DS release rate. These results revealed that DS could be formulated as an osmotic pump system with a prolonged, zero-order release pattern.

Metal release rate from AISI 316L stainless steel and pure Fe, Cr and Ni into a synthetic biological medium--a comparison.

PubMed

Herting, G; Wallinder, I Odnevall; Leygraf, C

2008-09-01

Metal release rates from stainless steel grade 316L were investigated in artificial lysosomal fluid (ALF), simulating a human inflammatory cell response. The main focus was placed on release rates of main alloying elements using graphite furnace atomic absorption spectroscopy, and changes in surface oxide composition by means of X-ray photoelectron spectroscopy. To emphasise that alloys and pure metals possess totally different intrinsic properties, comparative studies were performed on the pure alloying constituents: iron, nickel and chromium. Significant differences in release rates were observed due to the presence of a passive surface film on stainless steel. Iron and nickel were released at rates more than 300 times lower from the 316L alloy compared with the pure metals whereas the release rate of chromium was similar. Iron was preferentially released compared with nickel and chromium. Immersion in ALF resulted in the gradual enrichment of chromium in the surface film, a small increase of nickel, and the reduction of oxidized iron with decreasing release rates of alloy constituents as a result. As expected, released metals from stainless steel grade 316L were neither in proportion to the bulk alloy composition nor to the surface film composition.

Effect of biochar and digestate on microbial respiration and pesticide degradation

NASA Astrophysics Data System (ADS)

Mukherjee, Santanu; Tappe, Wolfgang; Hofmann, Diana; Köppchen, Stephan; Disko, Ulrich; Weihermüller, Lutz; Burauel, Peter; Vereecken, Harry

2014-05-01

To overcome the problem of on farm point sources of pollution stemming from improper handling, spillages, and leakages of pesticides during filling and cleaning of spraying equipment, environmental friendly and low cost technology filter systems are currently under development. Based on a laboratory screening approach, where different biomixtures (soil, with biochar and/or digestate) are tested a full scale outdoor system will be developed. Therefore, different fundamental processes like pesticide mineralization, metabolization, sorption-desorption, and transport behavior of three radiolabelled pesticides (Bentazone, Boscalid and Pyrimethanil) will be investigated. Biochar and digestate mixtures with two contrasting soils (sandy and silt loam) had been used as a novel biofilter material for respiration study instead of conventional soil and straw mixtures. To analyze the pesticide degradation potential and to gain information about the temporal evolution of the degradation process of the biochar and digestate soil mixtures microbial respiration was measured over the course of three month. As expected, digestate acts as an easily available C-source leading to highest release of CO2 compared to other biomixtures used. In contrast, the addition of even small amounts (1 %) of biochar caused a profound suppression in the CO2 release from digestate based mixtures. The exact driving mechanism for this suppression can be manifold likes negative priming or chemisorption of CO2 on biochar or NH3 toxicity induced by the large amount of digestate applied in the experiment (30 %) or can be combination of all effects. Surprisingly, a repeated experiment with same but aged digestate did not show such negative priming. On the other hand, the fate of applied organic contaminants to biomixtures depends on several factors like soil properties and climatic conditions as well as biological degradation. To analyze the degradation potential of the different soil/amendment mixtures a degradation study was performed to determine the effects of biochar and digestate in different mixing rates on the metabolization behavior of the studied pesticides, and to identify and quantify the metabolites derived during the degradation process. The results from the 14C Bentazone study indicate that 5 % digestate and 5 % biochar mixture showed highest (nearly~ 15 %) and 1 % biochar lowest rate of mineralization (~1 %), whereby highest microbial activity was measured in the soil/digestate mixture.

Comparison of elastic properties of nickel-titanium orthodontic archwires.

PubMed

Sarul, Michał; Kowala, Beata; Antoszewska, Joanna

2013-01-01

Cognizance of the mechanical properties of nickel-titanium archwires is necessary for the management of orthodontic therapy with fixed appliances. Acting on the periodontium with forces that are too heavy may lead to such complications as: pain, tooth root resorption and destruction of the alveolar bone and may also lead to retardation in tooth movement. The aim of the study was to assess the activation and deactivation forces of nickel-titanium archwires: Titanol Superelastic, Copper NiTi 35oC and NeoSentalloy. The examined material was 90 samples of Titanol Superelastic, Copper NiTi 35oC and NeoSentalloy with diameters of 0.016 and 0.016 x 0.022. All tests were carried out on the Zwick mechanical tests machine at a temperature of 30o C. In the group of archwires with diameters 0.016, the levels of deactivation forces were, respectively, from highest to lowest: Titanol Supertelastic, NeoSentalloy, Copper NiTi 35oC. In the group of rectangular archwires 0.016 x 0.022, the highest deactivation forces were released in Titanol Superelastic. With the high levels of deflection, 0.016 x 0.022 NeoSentalloy archwires released statistically significantly higher levels of force than 0.016 x 0.022 Copper NiTi 35o C, but this force diminished rapidly with lower deflection and below 3 mm of deflection, the highest forces were released by Copper NiTi 35o C. Testing the mechanical properties of the nickel-titanium wires of various diameters, it was found that round section wires release forces which fall within the range of optimal forces.

78 FR 37176 - Addition of Nonylphenol Category; Community Right-to-Know Toxic Chemical Release Reporting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-20

...]g/L. Nearly all larvae were abnormal at the two highest exposure concentrations (>= 53 [micro]g/L... was delayed at the two highest concentrations (14 and 23 [micro]g/L). Fathead minnow survival was... [micro]g/L (Ref. 35). 2. In Vivo Responses in Fish. The protein vitellogenin, which is produced in the...

Nanostructured lipid carriers: effect of solid phase fraction and distribution on the release of encapsulated materials.

PubMed

Dan, Nily

2014-11-25

Emulsions, solid lipid nanoparticles (SLN), and nanostructured lipid carriers (NLC) containing a mix of liquid and solid domains are of interest as encapsulation vehicles for hydrophobic compounds. Studies of the release rate from these particles yield contradictory results: Some find that increasing the fraction of solid phase increases the rate of release and others the opposite. In this paper we study the release of encapsulated materials from lipid-based nanoparticles using Monte Carlo simulations. We find that, quite surprisingly, the release rate is largely insensitive to the size of solid domains or the fraction of solid phase. However, the distribution of the domains significantly affects the rate of release: Solid domains located at the interface with the surrounding solution inhibit transport, while nanoparticles where the solid domains are concentrated in the center enhance it. The latter can lead to release rates in NLCs that are faster than in the equivalent emulsions. We conclude that controlling the release rate from NLCs requires the ability to determine the location and distribution of the solid phase, which may be achieved through choice of the surfactants stabilizing the particles, incorporation of nucleation sites, and/or the cooling rates and temperatures.

Waste activated sludge fermentation: effect of solids retention time and biomass concentration.

PubMed

Yuan, Q; Sparling, R; Oleszkiewicz, J A

2009-12-01

Laboratory scale, room temperature, semi-continuous reactors were set-up to investigate the effect of solids retention time (SRT, equal to HRT hydraulic retention time) and biomass concentration on generation of volatile fatty acids (VFA) from the non-methanogenic fermentation of waste activated sludge (WAS) originating from an enhanced biological phosphorus removal process. It was found that VFA yields increased with SRT. At the longest SRT (10d), improved biomass degradation resulted in the highest soluble to total COD ratio and the highest VFA yield from the influent COD (0.14g VFA-COD/g TCOD). It was also observed that under the same SRT, VFA yields increased when the biomass concentration decreased. At a 10d SRT the VFA yield increased by 46%, when the biomass concentration decreased from 13g/L to 4.8g/L. Relatively high nutrient release was observed during fermentation. The average phosphorus release was 17.3mg PO(4)-P/g TCOD and nitrogen release was 25.8mg NH(4)-N/g TCOD.

Starch and antioxidant compound release during in vitro gastrointestinal digestion of gluten-free pasta.

PubMed

Camelo-Méndez, Gustavo A; Agama-Acevedo, Edith; Rosell, Cristina M; de J Perea-Flores, Maria; Bello-Pérez, Luis A

2018-10-15

The microstructure of cooked gluten-free pasta depends on the ingredients used, and this microstructure affects the starch hydrolysis (SH), the release of phenolic compounds (PC) and their antioxidant capacity (AC). The aim of this study was to evaluate the SD and bioaccessibility of PC during in vitro gastrointestinal digestion of gluten-free pasta and its relationship with the microstructure. The highest SH was during the intestinal phase (≈60%), but pasta with the highest content of unripe plantain and chickpea presented the lowest release of PC (≈60%). The insoluble dietary fibre could be responsible (≈12.5%) for these effects. The cooked pasta showed high AC in the intestinal phase. Regions with gelatinized starch granules in a less dense protein network and other regions with intact or swollen granules surrounded by a protein network were observed. The starch digestion and bioaccessibility of PC were related to the structure of the matrix. Copyright © 2018 Elsevier Ltd. All rights reserved.

Effect of gonadotropin-releasing hormone II receptor (GnRHR-II) knockdown on testosterone secretion in the boar

USDA-ARS?s Scientific Manuscript database

Unlike the classical gonadotropin-releasing hormone (GnRH-I), the second mammalian GnRH isoform (GnRH-II; His5, Trp7, Tyr8) is a poor stimulator of gonadotropin secretion. In addition, GnRH-II is ubiquitously expressed, with transcript levels highest in tissues outside of the brain. A receptor speci...

Worker productivity and herbicide usage for pine release with manual application methods

Treesearch

James H. Miller; G.R. Glover

1993-01-01

Abstract. Productivity, herbicide usage, and costs of manually-applied pine release treatments were examined with linear regression analysis and compared. Data came from a replicated study in a 3-year-old loblolly pine plantation in Alabama’s Piedmont. Brush sawing had the highest labor costs but lowest total treatment costs. While of the...

Reduction of Tribocorrosion Products When using the Platform-Switching Concept.

PubMed

Alrabeah, G O; Knowles, J C; Petridis, H

2018-03-01

The reduced marginal bone loss observed when using the platform-switching concept may be the result of reduced amounts of tribocorrosion products released to the peri-implant tissues. Therefore, the purpose of this study was to compare the tribocorrosion product release from various platform-matched and platform-switched implant-abutment couplings under cyclic loading. Forty-eight titanium implants were coupled with pure titanium, gold alloy, cobalt-chrome alloy, and zirconia abutments forming either platform-switched or platform-matched groups ( n = 6). The specimens were subjected to cyclic occlusal forces in a wet acidic environment for 24 h followed by static aqueous immersion for 6 d. The amount of metal ions released was measured using inductively coupled plasma mass spectrometry. Microscopic evaluations were performed pre- and postimmersion under scanning electron microscope (SEM) equipped with energy-dispersive spectroscopy X-ray for corrosion assessment at the interface and wear particle characterization. All platform-switched groups showed less metal ion release compared with their platform-matched counterparts within each abutment material group ( P < 0.001). Implants connected to platform-matched cobalt-chrome abutments demonstrated the highest total mean metal ion release (218 ppb), while the least total mean ion release (11 ppb) was observed in the implants connected to platform-switched titanium abutments ( P ≤ 0.001). Titanium was released from all test groups, with its highest mean release (108 ppb) observed in the implants connected to platform-matched gold abutments ( P < 0.001). SEM images showed surface tribocorrosion features such as pitting and bands of fretting scars. Wear particles were mostly titanium, ranging from submicron to 48 µm in length. The platform-matched groups demonstrated a higher amount of metal ion release and more surface damage. These findings highlight the positive effect of the platform-switching concept in the reduction of tribocorrosion products released from dental implants, which consequently may minimize the adverse tissue reactions that lead to peri-implant bone loss.

Screening and evaluation of the glucoside hydrolase activity in Saccharomyces and Brettanomyces brewing yeasts.

PubMed

Daenen, L; Saison, D; Sterckx, F; Delvaux, F R; Verachtert, H; Derdelinckx, G

2008-02-01

The aim of this study was to select and examine Saccharomyces and Brettanomyces brewing yeasts for hydrolase activity towards glycosidically bound volatile compounds. A screening for glucoside hydrolase activity of 58 brewing yeasts belonging to the genera Saccharomyces and Brettanomyces was performed. The studied Saccharomyces brewing yeasts did not show 1,4-beta-glucosidase activity, but a strain dependent beta-glucanase activity was observed. Some Brettanomyces species did show 1,4-beta-glucosidase activity. The highest constitutive activity was found in Brettanomyces custersii. For the most interesting strains the substrate specificity was studied and their activity was evaluated in fermentation experiments with added hop glycosides. Fermentations with Br. custersii led to the highest release of aglycones. Pronounced exo-beta-glucanase activity in Saccharomyces brewing yeasts leads to a higher release of certain aglycones. Certain Brettanomyces brewing yeasts, however, are more interesting for hydrolysis of glycosidically bound volatiles of hops. The release of flavour active compounds from hop glycosides opens perspectives for the bioflavouring and product diversification of beverages like beer. The release can be enhanced by using Saccharomyces strains with high exo-beta-glucanase activity. Higher activities can be found in Brettanomyces species with beta-glucosidase activity.

Proteolytic enzyme activities in Cheddar cheese juice made using lactococcal starters of differing autolytic properties.

PubMed

Sheehan, A; Cuinn, G O'; Fitzgerald, R J; Wilkinson, M G

2006-04-01

To determine proteolytic enzyme activities released in Cheddar cheese juice manufactured using lactococcal starter strains of differing autolytic properties. The activities of residual chymosin, cell envelope proteinase and a range of intracellular proteolytic enzymes were determined during the first 70 days of ripening when starter lactococci predominate the microbial flora. In general, in cell free extracts (CFE) of the strains, the majority of proteolytic activities was highest for Lactococcus lactis HP, intermediate for L. lactis AM2 and lowest for L. lactis 303. However, in cheese juice, as ripening progressed, released proteolytic activities were highest for the highly autolytic strain L. lactis AM2, intermediate for L. lactis 303 and lowest for L. lactis HP. These results indicate that strain related differences in autolysis influence proteolytic enzyme activities released into Cheddar cheese during ripening. No correlation was found between proteolytic potential of the starter strains measured in CFE prior to cheese manufacture and levels of activities released in cheese juice. The findings further support the importance of autolysis of lactococcal starters in determining the levels of proteolytic activities present in cheese during initial stages of ripening.

Fine-scale hydrodynamics influence the spatio-temporal distribution of harbour porpoises at a coastal hotspot

NASA Astrophysics Data System (ADS)

Jones, A. R.; Hosegood, P.; Wynn, R. B.; De Boer, M. N.; Butler-Cowdry, S.; Embling, C. B.

2014-11-01

The coastal Runnelstone Reef, off southwest Cornwall (UK), is characterised by complex topography and strong tidal flows and is a known high-density site for harbour porpoise (Phocoena phocoena); a European protected species. Using a multidisciplinary dataset including: porpoise sightings from a multi-year land-based survey, Acoustic Doppler Current Profiling (ADCP), vertical profiling of water properties and high-resolution bathymetry; we investigate how interactions between tidal flow and topography drive the fine-scale porpoise spatio-temporal distribution at the site. Porpoise sightings were distributed non-uniformly within the survey area with highest sighting density recorded in areas with steep slopes and moderate depths. Greater numbers of sightings were recorded during strong westward (ebbing) tidal flows compared to strong eastward (flooding) flows and slack water periods. ADCP and Conductivity Temperature Depth (CTD) data identified fine-scale hydrodynamic features, associated with cross-reef tidal flows in the sections of the survey area with the highest recorded densities of porpoises. We observed layered, vertically sheared flows that were susceptible to the generation of turbulence by shear instability. Additionally, the intense, oscillatory near surface currents led to hydraulically controlled flow that transitioned from subcritical to supercritical conditions; indicating that highly turbulent and energetic hydraulic jumps were generated along the eastern and western slopes of the reef. The depression and release of isopycnals in the lee of the reef during cross-reef flows revealed that the flow released lee waves during upslope currents at specific phases of the tidal cycle when the highest sighting rates were recorded. The results of this unique, fine-scale field study provide new insights into specific hydrodynamic features, produced through tidal forcing, that may be important for creating predictable foraging opportunities for porpoises at a local scale. Information on the functional mechanisms linking porpoise distribution to static and dynamic physical habitat variables is extremely valuable to the monitoring and management of the species within the context of European conservation policies and marine renewable energy infrastructure development.

Modelling and assessment of accidental oil release from damaged subsea pipelines.

PubMed

Li, Xinhong; Chen, Guoming; Zhu, Hongwei

2017-10-15

This paper develops a 3D, transient, mathematical model to estimate the oil release rate and simulate the oil dispersion behavior. The Euler-Euler method is used to estimate the subsea oil release rate, while the Eulerian-Lagrangian method is employed to track the migration trajectory of oil droplets. This model accounts for the quantitative effect of backpressure and hole size on oil release rate, and the influence of oil release rate, oil density, current speed, water depth and leakage position on oil migration is also investigated in this paper. Eventually, the results, e.g. transient release rate of oil, the rise time of oil and dispersion distance are determined by above-mentioned model, and the oil release and dispersion behavior under different scenarios is revealed. Essentially, the assessment results could provide a useful guidance for detection of leakage positon and placement of oil containment boom. Copyright © 2017 Elsevier Ltd. All rights reserved.

The influence of litter quality and micro-habitat on litter decomposition and soil properties in a silvopasture system

NASA Astrophysics Data System (ADS)

Tripathi, G.; Deora, R.; Singh, G.

2013-07-01

Studies to understand litter processes and soil properties are useful for maintaining pastureland productivity as animal husbandry is the dominant occupation in the hot arid region. We aimed to quantify how micro-habitats and combinations of litters of the introduced leguminous tree Colophospermum mopane with the grasses Cenchrus ciliaris or Lasiurus sindicus influence decomposition rate and soil nutrient changes in a hot desert silvopasture system. Litter bags with tree litter alone (T), tree + C. ciliaris in 1:1 ratio (TCC) and tree + L. sindicus 1:1 ratio (TLS) litter were placed inside and outside of the C. mopane canopy and at the surface, 3-7 cm and 8-12 cm soil depths. We examined litter loss, soil fauna abundance, organic carbon (SOC), total (TN), ammonium (NH4-N) and nitrate (NO3-N) nitrogen, phosphorus (PO4-P), soil respiration (SR) and dehydrogenase activity (DHA) in soil adjacent to each litter bag. After 12 months exposure, the mean residual litter was 40.2% of the initial value and annual decomposition rate constant (k) was 0.98 (0.49-1.80). Highest (p < 0.01) litter loss was in the first four months, when faunal abundance, SR, DHA and humidity were highest but it decreased with time. These variables and k were highest under the tree canopies. The litter loss and k were highest (p < 0.01) in TLS under the tree canopy, but the reverse trend was found for litter outside the canopy. Faunal abundance, litter loss, k, nutrient release and biochemical activities were highest (p < 0.01) in the 3-7 cm soil layer. Positive correlations of litter loss and soil fauna abundance with soil nutrients, SR and DHA demonstrated the interactions of litter quality and micro-habitats together with soil fauna on increased soil fertility. These results suggest that a Colophospermum mopane and L. sindicus silvopasture system best promotes faunal abundance, litter decomposition and soil fertility. The properties of these species and the associated faunal resources may be utilised as an ecosystem-restoration strategy in designing a silvopasture system. This may help to control land degradation and increase productivity sustainably in this environment.

5 CFR 532.405 - Use of highest previous rate.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Use of highest previous rate. 532.405 Section 532.405 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS PREVAILING RATE SYSTEMS Pay Administration § 532.405 Use of highest previous rate. (a)(1) Subject to the...

Efficient Anaerobic Digestion of Microalgae Biomass: Proteins as a Key Macromolecule.

PubMed

Magdalena, Jose Antonio; Ballesteros, Mercedes; González-Fernandez, Cristina

2018-05-06

Biogas generation is the least complex technology to transform microalgae biomass into bioenergy. Since hydrolysis has been pointed out as the rate limiting stage of anaerobic digestion, the main challenge for an efficient biogas production is the optimization of cell wall disruption/hydrolysis. Among all tested pretreatments, enzymatic treatments were demonstrated not only very effective in disruption/hydrolysis but they also revealed the impact of microalgae macromolecular composition in the anaerobic process. Although carbohydrates have been traditionally recognized as the polymers responsible for the low microalgae digestibility, protease addition resulted in the highest organic matter solubilization and the highest methane production. However, protein solubilization during the pretreatment can result in anaerobic digestion inhibition due to the release of large amounts of ammonium nitrogen. The possible solutions to overcome these negative effects include the reduction of protein biomass levels by culturing the microalgae in low nitrogen media and the use of ammonia tolerant anaerobic inocula. Overall, this review is intended to evidence the relevance of microalgae proteins in different stages of anaerobic digestion, namely hydrolysis and methanogenesis.

Capturing CD4 cells using a functionalized circular microfluidic device and glutaraldehyde as biolinker for tuberculosis detection and diagnosis

NASA Astrophysics Data System (ADS)

Shih, Yeu-Farn; Huang, Nien-Tsu; Lee, Chih-Kung

2015-03-01

It is estimated that about one-third of the world's population has already been infected by tuberculosis. Mycobacterium tuberculosis, in general, can result in an active case of tuberculosis in approximately 5%-10% of those who suffer from latent tuberculosis and the chance of becoming ill is the highest within one of year of getting the disease. Although a newly developed methods called interferon gamma release assay (IGRA) can monitor CD4 cells secreted cytokine to diagnose tuberculosis (TB) condition. However, it is difficult to count total numbers of cytokine secreted CD4 cells, which make the diagnosis less accurate. Therefore, we develop a functionalized polydimethylsiloxane (PDMS) device using glutaraldehyde to capture CD4 cells. To enhance the capture efficiency, we use COMSOL simulation to optimize the arrangement of PDMS micro pillars to make cells uniformly distributed in the device. Our preliminary data showed the microfluidic configuration in a circular shape with HCP patterned micro pillars turned 30 degrees offers the highest cell capture rate.

Influence of mastication rate on dynamic flavour release analysed by combined model mouth/proton transfer reaction-mass spectrometry

NASA Astrophysics Data System (ADS)

van Ruth, Saskia M.; Buhr, Katja

2004-12-01

The influence of mastication rate on the dynamic release of seven volatile flavour compounds from sunflower oil was evaluated by combined model mouth/proton transfer reaction-mass spectrometry (PTR-MS). Air/oil partition coefficients were measured by static headspace gas chromatography. The dynamic release of the seven volatile flavour compounds from sunflower oil was significantly affected by the compounds' hydrophobicity and the mastication rate employed in the model mouth. The more hydrophobic compounds were released at a higher rate than their hydrophilic counterparts. Increase in mastication rate increased the maximum concentration measured by 36% on average, and the time to reach this maximum by 35% on average. Mastication affected particularly the release of the hydrophilic compounds. The maximum concentration of the compounds correlated significantly with the compounds' air/oil partition coefficients. The initial release rates over the first 15 s were affected by the type of compound, but not by the mastication rate. During the course of release, the proportions of the hydrophilic compounds to the overall flavour mixture in air decreased. The contribution of the hydrophobic compounds increased. Higher mastication rates, however, increased the proportions of the hydrophilic compounds and decreased those of the hydrophobic compounds.

Heat release rate of wood-plastic composites

Treesearch

N. M. Stark; R. H. White; C. M. Clemons

1997-01-01

Wood-plastic composites are becoming more important as a material that fulfills recycling needs. In this study, fire performance tests were conducted on several compositions of wood and plastic materials using the Ohio State University rate of heat release apparatus. Test results included five-minute average heat release rate in kW/m2 (HRR avg) and maximum heat release...

Encapsulation of lemongrass oil with cyclodextrins by spray drying and its controlled release characteristics.

PubMed

Phunpee, Sarunya; Ruktanonchai, Uracha Rangsadthong; Yoshii, Hidefumi; Assabumrungrat, Suttichai; Soottitantawat, Apinan

2017-04-01

Inclusion of the two isomers of citral (E-citral and Z-citral), components of lemongrass oil, was investigated within the confines of various cyclodextrin (α-CD, β-CD and γ-CD) host molecules. Aqueous complex formation constants for E-citral with α-CD, β-CD and γ-CD were determined to be 123, 185, and 204 L/mol, respectively, whereas Z-citral exhibited stronger affinities (157, 206, and 253 L/mol, respectively). The binding trend γ-CD > β-CD > α-CD is a reflection of the more favorable geometrical accommodation of the citral isomers with increasing cavity size. Encapsulation of lemongrass oil within CDs was undertaken through shaking citral:CD (1:1, 1.5:1, and 2:1 molar ratio) mixtures followed by spray drying. Maximum citral retention occurred at a 1:1 molar ratio with β-CD and α-CD demonstrating the highest levels of total E-citral and Z-citral retention, respectively. Furthermore, the β-CD complex demonstrated the slowest release rate of all inclusion complex powders.

Photopheresis with UV-A light and 8-methoxypsoralen leads to cell death and to release of blebs with anti-inflammatory phenotype in activated and non-activated lymphocytes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stadler, K.; Frey, B.; Munoz, L.E.

2009-08-14

Background: Extracorporeal photopheresis is a therapy for treatment of autoimmune diseases, cutaneous T-cell lymphoma, organ graft rejection as well as graft-versus-host diseases. The exact mechanism how the combination of 8-methoxypsoralen plus UV-A irradiation (PUVA) acts is still unclear. We investigated the cell death of activated and non-activated lymphocytes after PUVA treatment as well as the rate of released blebs and their antigen composition. Results: In presence of 8-MOP, UV-A light highly significantly increased the cell death of activated lymphocytes. The same was observed to a lesser extent in non-activated cells. Blebs derived from activated lymphocytes after PUVA treatment showed themore » highest surface exposition of phosphatidylserine. These blebs also displayed a high exposure of the antigens CD5 and CD8 as well as a low exposure of CD28 and CD86. Conclusion: PUVA treatment exerts anti-inflammatory effects by inducing apoptosis and apoptotic cell-derived blebs with immune suppressive surface composition.« less

Burning rate of solid wood measured in a heat release rate calorimeter

Treesearch

H. C. Tran; R. H. White

1992-01-01

Burning rate is a key factor in modeling fire growth and fire endurance of wood structures. This study investigated the burning rate of selected wood materials as determined by heat release, mass loss and charring rates. Thick samples of redwood, southern pine, red oak and basswood were tested in a heat release rate calorimeter. Results on ignitability and average beat...

Comparison of the Kinetic Rate Law Parameters for the Dissolution of Natural and Synthetic Autunite in the Presence of Aqueous Bicarbonate Ions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gudavalli, Ravi; Katsenovich, Yelena; Wellman, Dawn M.

2013-08-02

Bicarbonate is one of the most significant components within the uranium geochemical cycle. In aqueous solutions, bicarbonate forms strong complexes with uranium. As such, aqueous bicarbonate may significantly increase the rate of uranium release from uranium minerals. Quantifying the relationship of aqueous bicarbonate concentration to the rate of uranium release during dissolution is critical to understanding the long-term fate of uranium within the environment. Single-pass flow-through (SPTF) experiments were conducted to estimate the rate of uranium release from Na meta-autunite as a function of bicarbonate (0.0005-0.003 M) under the pH range of 6-11 and a temperature range of 5-60oC. Consistentmore » with the results of previous investigation, the rate of uranium release exhibited minimal dependency on temperature; but were strongly dependent on pH. Increasing aqueous bicarbonate concentrations afforded comparable increases in the rate of release of uranium. Most notably under low pH conditions the aqueous bicarbonate resulted in up to 370 fold increases in the rate of uranium release in relative to the rate of uranium release in the absence of bicarbonate. However, the effect of aqueous bicarbonate on the release of uranium was significantly less under higher pH conditions. It is postulated that at high pH values, surface sites are saturated with carbonate, thus the addition of more bicarbonate would have less effect on uranium release.« less

Monomer Release from Resin Based Dental Materials Cured With LED and Halogen Lights

PubMed Central

Ak, Asli Topaloglu; Alpoz, A. Riza; Bayraktar, Oguz; Ertugrul, Fahinur

2010-01-01

Objectives: To measure the release of TEGDMA and BisGMA from two commercially available composite resins; Filtek Z 250 (3M ESPE, Germany), Leaddent (Leaddent, Germany) and two fissure sealants; Helioseal F (3M ESPE, Germany) Enamel Loc (Premiere Rev, USA) over 1, 3 and 7 days after polymerization with standard quartz-tungsten halogen Coltolux II (QHL) (Coltene Switzerland) and a standard blue light emitting diode Elipar Freelight 2 (3M ESPE, Germany). Methods: 9 samples of each material were placed in disc shaped specimens in 1 mm of thickness and 10 mm in diameter (n=36). Each material was polymerized using LED for 20 s (n=12), 40 s (n=12) and halogen for 40 s (n=12), respectively. High Performance Liquid Chromatography (HPLC) was used to measure the amount of monomers released over 1, 3 and 7 days. Data was analyzed using one way ANOVA and Bonferroni test for multiple comparisons with a significance level of .05. Results: LED 20 sec group showed the highest release of monomers at 1, 3 and 7 days in sealant groups. Halogen 40 sec group resulted highest release of monomers for Leaddent at all time intervals (P<.05) Conclusions: Efficiency of the curing unit and applying the recommended curing time of the light activated resin based dental materials is very important to protect the patient from potential hazards of residual monomers. PMID:20046478

Copper Corrosion and Biocorrosion Events in Premise Plumbing

PubMed Central

Fischer, Diego A.; Alsina, Marco A.; Pastén, Pablo A.

2017-01-01

Corrosion of copper pipes may release high amounts of copper into the water, exceeding the maximum concentration of copper for drinking water standards. Typically, the events with the highest release of copper into drinking water are related to the presence of biofilms. This article reviews this phenomenon, focusing on copper ingestion and its health impacts, the physicochemical mechanisms and the microbial involvement on copper release, the techniques used to describe and understand this phenomenon, and the hydrodynamic effects. A conceptual model is proposed and the mathematical models are reviewed. PMID:28872628

Copper Corrosion and Biocorrosion Events in Premise Plumbing.

PubMed

Vargas, Ignacio T; Fischer, Diego A; Alsina, Marco A; Pavissich, Juan P; Pastén, Pablo A; Pizarro, Gonzalo E

2017-09-05

Corrosion of copper pipes may release high amounts of copper into the water, exceeding the maximum concentration of copper for drinking water standards. Typically, the events with the highest release of copper into drinking water are related to the presence of biofilms. This article reviews this phenomenon, focusing on copper ingestion and its health impacts, the physicochemical mechanisms and the microbial involvement on copper release, the techniques used to describe and understand this phenomenon, and the hydrodynamic effects. A conceptual model is proposed and the mathematical models are reviewed.

The relationship between functional sciatic nerve block duration and the rate of release of lidocaine from a controlled-release matrix.

PubMed

Gerner, Peter; Wang, Chi-Fei; Lee, Byung-Sang; Suzuki, Suzuko; Degirolami, Umberto; Gandhi, Ankur; Knaack, David; Strichartz, Gary

2010-07-01

Nerve blocks of long duration are often desirable in perioperative and postoperative situations. The relationship between the duration of such blocks and the rate at which a local anesthetic is released is important to know for developing a localized drug delivery system that will optimize block duration. Lidocaine concentration was varied in 1 series of formulations (OSB-L) containing a constant amount of release rate modifier. In another series (OST-R), the release rate modifier was varied while the lidocaine content was held constant. Release kinetics were measured in vitro and correlated to the in vivo duration of antinociceptive and motor block effects when the formulation was implanted next to the rat sciatic nerve. In parallel studies, rats receiving different formulations of slow-release lidocaine were fixed by intracardiac perfusion with 4% paraformaldehyde and nerve-muscle tissue taken for histopathological analysis. In this study, we have demonstrated that the most important variable for effecting functional nerve block, i.e., the blockade of impulses in the relevant fibers of the sciatic nerve, is the rate of lidocaine release at that time. For the OSB-L formulations (lidocaine concentrations of 1.875%, 3.75%, 7.5%, and 15% at a constant release rate modifier of 5%), the average in vitro release rates at 50% recovery of motor block and nociceptive block were 0.91 +/- 0.28 and 1.75 +/- 0.61 mg/h, respectively. For the OST-R formulations (16% lidocaine with release rate modifier concentrations of 1.875%, 3.75%, 7.5%, and 15%), the average in vitro release rates at 50% recovery of motor block and nociceptive block were 2.33 +/- 1.39 and 4.34 +/- 1.09 mg/h, respectively. The OSB-L formulations showed a dose-dependent increase in block duration proportional to an increase in initial lidocaine concentration, whereas the OST-R formulations showed a nonmonotonic relationship between release rate modifier concentration and block duration. The histopathological studies at 24 hours, 3, 5, or 7 days, and 4 weeks after the implantation revealed inflammatory reactions with degrees correlated with lidocaine content, but limited to the connective tissue and muscle immediately surrounding the implanted material. Despite these observed inflammatory reactions, nociceptive and motor block function returned to normal, preimplantation values in all animals. Increasing initial lidocaine content proportionately increased the duration of functional sciatic nerve block. However, decreasing the release rate per se does not give a proportional increase in block duration. Instead, there seems to be an optimal, intermediate release rate for achieving the maximum duration of block.

Exocrine and endocrine release of kallikrein after reflex-induced salivary secretion.

PubMed

Berg, T; Johansen, L; Poulsen, K

1990-05-01

Exocrine and endocrine release of rat submandibular gland kallikrein has been shown to be low after parasympathetic and beta-adrenergic stimulation but greatly increased after alpha-adrenergic stimulation. In the present study, release of glandular kallikrein was investigated under conditions known to give a reflex-induced salivary gland response. Heat stress induced a rich flow of saliva originating in the submandibular glands. Salivary kallikrein secretory rate was higher than after parasympathetic stimulation but lower than after sympathetic stimulation (P less than 0.005). Only heat stress increased circulating glandular kallikrein (12.7 +/- 0.8 ng ml-1 before heat exposure and 53.3 +/- 14.1 ng ml-1 40 min afterwards, P less than 0.005). There were no indications that the endocrine release of kallikrein was due to non-specific leakage. Atropine abolished heat-induced salivation and endocrine kallikrein secretion, possibly through interference with central pathways (P less than 0.05). However, phentolamine did not, which may indicate as an yet unidentified mediator of endogenous kallikrein release. The salivary gland response to acid and ether was comparable to that observed after parasympathetic nerve stimulation and was abolished by atropine (P less than 0.005). Stimuli known to influence other salivary gland ductal cells, such as aggression and starvation followed by drinking, also did not increase the plasma concentration of glandular kallikrein. The fact that various conditions which induce salivation did not increase circulating glandular kallikrein, coupled with the fact that kallikrein concentration was the highest in animals that died from heat stress, may suggest that the increase in circulating glandular kallikrein seen after heat stress may be pathological and could contribute to the development of heat shock.

Novel chronotherapeutic rectal aminophylline delivery system for therapy of asthma.

PubMed

Shiohira, Hideo; Fujii, Makiko; Koizumi, Naoya; Kondoh, Masuo; Watanabe, Yoshiteru

2009-09-08

The aim of this study was to develop a new chronotherapeutic pharmaceutical preparation as a sustained-release suppository for prevention and therapeutic use against bronchial asthma in the early morning. Sustained-release hollow-type (SR-HT) suppositories using sodium alginate (Alg-Na), sodium polyacrylate (PANa) or polyacrylate-PANa co-polymer (PA-PANa) as gelling polymers (gel agent) were prepared and pharmaceutical characteristics of these suppositories were investigated. Type A SR-HT suppositories comprised a suppository shell prepared with oleaginous base and containing aminophylline only or aminophylline with Alg-Na or PANa in the cavity (hollow space). Type B SR-HT suppositories comprised a suppository shell prepared with oleaginous base and gel agent (30%), with aminophylline in the hollow space. In drug-release studies, the acrylate polymer-containing suppositories showed linearity of delayed release rate, providing significantly decreased the highest concentration of theophylline in plasma (C(max)) and delayed the time required to reach C(max) (t(max)) and the mean residence time (MRT) after rectal administrated in rabbits. In particular, suppositories containing PA-PANa maintained significantly higher theophylline concentrations than control suppositories at 12h after rectal administration. Furthermore, histopathological examination indicated that these suppositories using acrylate polymers did not result in rectal lesions. The SR-HT suppository, particularly using PA-PANa as a gel agent, may thus be useful against nocturnal symptoms of asthma. In this study, we confirmed new formulation of sustained-release suppository for chronotherapy of theophylline using oily base material in combination with polymer such as PA-PANa. The hollow-type suppository containing oleaginous base and hydrophilic polymer in the shell could be useful device for rectal administration of various drugs with prolongation of plasma concentration.

Effect of loading force on the dissolution behavior and surface properties of nickel-titanium orthodontic archwires in artificial saliva.

PubMed

Liu, Jia-Kuang; Lee, Tzer-Min; Liu, I-Hua

2011-08-01

For orthodontic applications, equiatomic nickel-titanium (NiTi) wires are used to level and align the teeth under bending conditions in the oral environment for long periods. The aim of study was to investigate the influence of bending stress on the nickel release of commercial NiTi orthodontic wires in vitro, simulating the intraoral environment as realistically as possible. Two types of as-received orthodontic NiTi wires, free of performed internal stress, were immersed in artificial saliva. Half of the NiTi wires were exposed to continuous bending stress throughout the 14-day experimental period. The stressed NiTi wires exhibited substantial increases in the nickel release compared with the unstressed specimens during all experimental periods. The highest dissolution rate during the 0 to 1 day incubation period was observed for all stressed specimens. However, a slight increase of nickel released as a function of time was observed in the 3 groups of stressed specimens after 3 days of immersion. For the stressed specimens, it was hypothesized that the bending stress would induce buckling or cracking of the protective oxide film of the NiTi wires. In this study, the mechanism of nickel release was the underlying metal surface reacting with the surrounding environment. The results indicated that bending stress influences the nickel release of NiTi wires. The factor of loading condition with respect to corrosion behavior and passive film should be considered in view of the widespread use of NiTi wires for dental devices. Copyright © 2011 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Role of cellulose ether polymers on ibuprofen release from matrix tablets.

PubMed

Vueba, M L; Batista de Carvalho, L A E; Veiga, F; Sousa, J J; Pina, Maria Eugénia

2005-08-01

Cellulose derivatives are the most frequently used polymers in formulations of pharmaceutical products for controlled drug delivery. The main aim of the present work was to evaluate the effect of different cellulose substitutions on the release rate of ibuprofen (IBP) from hydrophilic matrix tablets. Thus, the release mechanism of IBP with methylcellulose (MC25), hydroxypropylcellulose (HPC), and hydroxypropylmethylcellulose (HPMC K15M or K100M) was studied. In addition, the influence of the diluents lactose monohydrate (LAC) and beta-cyclodextrin (beta-CD) was evaluated. Distinct test formulations were prepared containing: 57.14% of IBP, 20.00% of polymer, 20.29% of diluent, 1.71% of talc lubricants, and 0.86% of magnesium stearate as lubricants. Although non-negligible drug-excipient interactions were detected from DSC studies, these were found not to constitute an incompatibility effect. Tablets were examined for their drug content, weight uniformity, hardness, thickness, tensile strength, friability, porosity, swelling, and dissolution performance. Polymers MC25 and HPC were found to be unsuitable for the preparation of this kind of solid dosage form, while HPMC K15M and K100M showed to be advantageous. Dissolution parameters such as the area under the dissolution curve (AUC), the dissolution efficiency (DE(20 h)), dissolution time (t 50%), and mean dissolution time (MDT) were calculated for all the formulations, and the highest MDT values were obtained with HPMC indicating that a higher value of MDT signifies a higher drug retarding ability of the polymer and vice-versa. The analysis of the drug release data was performed in the light of distinct kinetic mathematical models-Kosmeyer-Peppas, Higuchi, zero-, and first-order. The release process was also found to be slightly influenced by the kind of diluent used.

Effective sampling range of food-based attractants for female Anastrepha suspensa (Diptera: Tephritidae).

PubMed

Kendra, Paul E; Epsky, Nancy D; Heath, Robert R

2010-04-01

Release-recapture studies were conducted with both feral and sterile females of the Caribbean fruit fly, Anastrepha suspensa (Loew) (Diptera: Tephritidae), to determine sampling range for a liquid protein bait (torula yeast/borax) and for a two-component synthetic lure (ammonium acetate and putrescine). Tests were done in a guava, Psidium guajava L., grove and involved releasing flies at a central point and recording the numbers captured after 7 h and 1, 2, 3, and 6 d in an array of 25 Multilure traps located 9-46 m from the release point. In all tests, highest rate of recapture occurred within the first day of release, so estimations of sampling range were based on a 24-h period. Trap distances were grouped into four categories (<10, 10-20, 20-30, and >30 m from release point) and relative trapping efficiency (percentage of capture) was determined for each distance group. Effective sampling range was defined as the maximum distance at which relative trapping efficiency was > or = 25%. This corresponded to the area in which 90% of the recaptures occured. Contour analysis was also performed to document spatial distribution of fly dispersal. In tests with sterile flies, immature females dispersed farther and were recovered in higher numbers than mature females, regardless of attractant, and recapture of both cohorts was higher with torula yeast. For mature feral flies, range of the synthetic lure was determined to be 30 m. With sterile females, effective range of both attractants was 20 m. Contour maps indicated that wind direction had a strong influence on the active space of attractants, as reflected by distribution of captured flies.

[Release and supplement of carbon, nitrogen and phosphorus from jellyfish (Nemopilema nomurai) decomposition in seawater].

PubMed

Qu, Chang-feng; Song, Jin-ming; Li, Ning; Li, Xue-gang; Yuan, Hua-mao; Duan, Li-qin

2016-01-01

Abstract: Jellyfish bloom has been increasing in Chinese seas and decomposition after jellyfish bloom has great influences on marine ecological environment. We conducted the incubation of Nemopilema nomurai decomposing to evaluate its effect on carbon, nitrogen and phosphorus recycling of water column by simulated experiments. The results showed that the processes of jellyfish decomposing represented a fast release of biogenic elements, and the release of carbon, nitrogen and phosphorus reached the maximum at the beginning of jellyfish decomposing. The release of biogenic elements from jellyfish decomposition was dominated by dissolved matter, which had a much higher level than particulate matter. The highest net release rates of dissolved organic carbon and particulate organic carbon reached (103.77 ± 12.60) and (1.52 ± 0.37) mg · kg⁻¹ · h⁻¹, respectively. The dissolved nitrogen was dominated by NH₄⁺-N during the whole incubation time, accounting for 69.6%-91.6% of total dissolved nitrogen, whereas the dissolved phosphorus was dominated by dissolved organic phosphorus during the initial stage of decomposition, being 63.9%-86.7% of total dissolved phosphorus and dominated by PO₄³⁻-P during the late stage of decomposition, being 50.4%-60.2%. On the contrary, the particulate nitrogen was mainly in particulate organic nitrogen, accounting for (88.6 ± 6.9) % of total particulate nitrogen, whereas the particulate phosphorus was mainly in particulate. inorganic phosphorus, accounting for (73.9 ±10.5) % of total particulate phosphorus. In addition, jellyfish decomposition decreased the C/N and increased the N/P of water column. These indicated that jellyfish decomposition could result in relative high carbon and nitrogen loads.

Attenuation of fluorocarbons released from foam insulation in landfills.

PubMed

Scheutz, Charlotte; Dote, Yutaka; Fredenslund, Anders M; Mosbaek, Hans; Kjeldsen, Peter

2007-11-15

Chlorofluorocarbons (CFCs), hydrochlorofluorocarbons (HCFCs), and hydrofluorocarbons (HFCs) have been used as blowing agents (BAs) for foam insulation in home appliances and building materials, which after the end of their useful life are disposed of in landfills. The objective of this project was to evaluate the potential for degradation of BAs in landfills, and to develop a landfill model, which could simulate the fate of BAs in landfills. The investigation was performed by use of anaerobic microcosm studies using different types of organic waste and anaerobic digested sludge as inoculum. The BAs studied were CFC-11, CFC-12, HCFC-141b, HFC-134a, and HFC-245fa. Experiments considering the fate of some of the expected degradations products of CFC-11 and CFC-12 were included like HCFC-21, HCFC-22, HCFC-31, HCFC-32, and HFC-41. Degradation of all studied CFCs and HCFCs was observed regardless the type of waste used. In general, the degradation followed first-order kinetics. CFC-11 was rapidly degraded from 590 microg L(-1) to less than 5 microg L(-1) within 15-20 days. The degradation pattern indicated a sequential production of HCFC-21, HCFC-31, and HFC-41. However, the production of degradation products did not correlate with a stoichiometric removal of CFC-11 indicating that other degradation products were produced. HCFC-21 and HCFC-31 were further degraded whereas no further degradation of HFC-41 was observed. The degradation rate coefficient was directly correlated with the number of chlorine atoms attached to the carbon. The highest degradation rate coefficient was obtained for CFC-11, whereas lower rates were seen for HCFC-21 and HCFC-31. Equivalent results were obtained for CFC-12. HCFC-141b was also degraded with rates comparable to HCFC-21 and CFC-12. Anaerobic degradation of the studied HFCs was not observed in any of the experiments within a run time of up to 200 days. The obtained degradation rate coefficients were used as input for an extended version of an existing landfill fate model incorporating a time dependent BA release from co-disposed foam insulation waste. Predictions with the model indicate that the emission of foam released BAs may be strongly attenuated by microbial degradation reactions. Sensitivity analysis suggests that there is a need for determination of degradation rates under more field realistic scenarios.

Fission-gas-release rates from irradiated uranium nitride specimens

NASA Technical Reports Server (NTRS)

Weinstein, M. B.; Kirchgessner, T. A.; Tambling, T. N.

1973-01-01

Fission-gas-release rates from two 93 percent dense UN specimens were measured using a sweep gas facility. Specimen burnup rates averaged .0045 and .0032 percent/hr, and the specimen temperatures ranged from 425 to 1323 K and from 552 to 1502 K, respectively. Burnups up to 7.8 percent were achieved. Fission-gas-release rates first decreased then increased with burnup. Extensive interconnected intergranular porosity formed in the specimen operated at over 1500 K. Release rate variation with both burnup and temperature agreed with previous irradiation test results.

Microbial degradation at a shallow coastal site: Long-term spectra and rates of exoenzymatic activities in the NE Adriatic Sea

NASA Astrophysics Data System (ADS)

Celussi, Mauro; Del Negro, Paola

2012-12-01

The degradation of organic matter along the water column is mediated by enzymes released into the environment by planktonic organisms. Variations in enzymes profiles (types and levels of activity) reflect the trophic status of the environment and could be caused by shifts in the dominant species or in the level of enzyme expression by the same species in response to changes in the spectrum of organic substrates. To explore this issue, we examined the maximum rates of hydrolysis of 6 different enzymes (protease, α-glucosidase, β-glucosidase, β-galactosidase, alkaline phosphatase and lipase) along the water column (4 depths) at a coastal station in the Gulf of Trieste (northern Adriatic Sea), from 2000 to 2005. Most of the studied enzymes exhibited a pronounced seasonal variability with winter minima and maxima from April to October. During summer, alkaline phosphatase, lipase and protease reached the highest activities, while polysaccharide degradation prevailed in spring and autumn, associated to phytoplankton blooms. Phosphatase/protease activities ratio was generally low, indicating that microbial communities were rarely P-limited, possibly because of the use of organic P sources. A pronounced interannual variability of degradation patterns was found, with maximum rates of protease being the highest in most of the samples, followed by the alkaline phosphatase's ones. Water column features greatly affected hydrolysis rates, being degradation of linear polysaccharides, lipids, phosphorilated compounds and polypeptides significantly different at different depths during stratified condition. Mixing processes affected especially α-glucosidase activity, possibly as a consequence of resuspension of organic matter from the seabed. Large-impact phenomena such as the 2003 heat wave and mucilage influenced the degradation of specific substrates. Mucilage enhanced lipase, phosphatase and protease, whereas a pronounced inhibition characterised phosphatase and protease during summer 2003.

The Effect of Calcium Phosphate Particle Shape and Size on their Antibacterial and Osteogenic Activity in the Delivery of Antibiotics in vitro

PubMed Central

Uskoković, Vuk; Batarni, Samir Shariff; Schweicher, Julien; King, Andrew; Desai, Tejal A.

2013-01-01

Powders composed of four morphologically different calcium phosphate particles were prepared by precipitation from aqueous solutions: flaky, brick-like, elongated orthogonal, and spherical. The particles were then loaded with either clindamycin phosphate as the antibiotic of choice, or fluorescein, a model molecule used to assess the drug release properties. A comparison was carried out of the comparative effect of such antibiotic-releasing materials on: sustained drug release profiles; Staphylococcus aureus growth inhibition; and osteogenic propensities in vitro. Raman spectroscopic analysis indicated the presence of various calcium phosphate phases, including monetite (flaky and elongated orthogonal particles), octacalcium phosphate (brick-shaped particles) and hydroxyapatite (spherical particles). Testing the antibiotic-loaded calcium phosphate powders for bacterial growth inhibition demonstrated satisfying antibacterial properties both in broths and on agar plates. All four calcium-phosphate-fluorescein powders exhibited sustained drug release over 21 days. The calcium phosphate sample with the highest specific surface area and the smallest, spherical particle size was the most effective in both drug loading and release, consequently having the highest antibacterial efficiency. Moreover, the highest cell viability, the largest gene expression upregulation of three different osteogenic markers – osteocalcin, osteopontin and Runx2 - as well as the least disrupted cell cytoskeleton and cell morphologies were also noticed for the calcium phosphate powder composed of smallest, spherical nanosized particles. Still, all four powders exerted a viable effect on osteoblastic MC3T3-E1 cells in vitro, as evidenced by both morphological assessments on fluorescently stained cells and measurements of their mitochondrial activity. The obtained results suggest that the nanoscale particle size and the corresponding coarseness of the surface of particle conglomerates as the cell attachment points may present a favorable starting point for the development of calcium-phosphate-based osteogenic drug delivery devices. PMID:23484624

Linking behavior, physiology, and survival of Atlantic Salmon smolts during estuary migration

USGS Publications Warehouse

Stich, Daniel S.; Zydlewski, Gayle B.; Kocik, John F.; Zydlewski, Joseph D.

2015-01-01

Decreased marine survival is identified as a component driver of continued declines of Atlantic Salmon Salmo salar. However, estimates of marine mortality often incorporate loss incurred during estuary migration that may be mechanistically distinct from factors affecting marine mortality. We examined movements and survival of 941 smolts (141 wild and 800 hatchery-reared fish) released in freshwater during passage through the Penobscot River estuary, Maine, from 2005 to 2013. We related trends in estuary arrival date, movement rate, and survival to fish characteristics, migratory history, and environmental conditions in the estuary. Fish that experienced the warmest thermal history arrived in the estuary 8 d earlier than those experiencing the coolest thermal history during development. Estuary arrival date was 10 d later for fish experiencing high flow than for fish experiencing low flow. Fish released furthest upstream arrived in the estuary 3 d later than those stocked further downstream but moved 0.5 km/h faster through the estuary. Temporally, movement rate and survival in the estuary both peaked in mid-May. Spatially, movement rate and survival both decreased from freshwater to the ocean. Wild smolts arrived in the estuary later than hatchery fish, but we observed no change in movement rate or survival attributable to rearing history. Fish with the highest gill Na+, K+-ATPase activity incurred 25% lower mortality through the estuary than fish with the lowest gill Na+, K+-ATPase activity. Smolt survival decreased (by up to 40%) with the increasing number of dams passed (ranging from two to nine) during freshwater migration. These results underscore the importance of physiological preparedness on performance and the delayed, indirect effects of dams on survival of Atlantic Salmon smolts during estuary migration, ultimately affecting marine survival estimates.

Variation in decomposition rates in the fynbos biome, South Africa: the role of plant species and plant stoichiometry.

PubMed

Bengtsson, Jan; Janion, Charlene; Chown, Steven L; Leinaas, Hans Petter

2011-01-01

Previous studies in the fynbos biome of the Western Cape, South Africa, have suggested that biological decomposition rates in the fynbos vegetation type, on poor soils, may be so low that fire is the main factor contributing to litter breakdown and nutrient release. However, the fynbos biome also comprises vegetation types on more fertile soils, such as the renosterveld. The latter is defined by the shrub Elytropappus rhinocerotis, while the shrub Galenia africana may become dominant in overgrazed areas. We examined decomposition of litter of these two species and the geophyte Watsonia borbonica in patches of renosterveld in an agricultural landscape. In particular, we sought to understand how plant species identity affects litter decomposition rates, especially through variation in litter stoichiometry. Decomposition (organic matter mass loss) varied greatly among the species, and was related to litter N and P content. G. africana, with highest nutrient content, lost 65% of its original mass after 180 days, while E. rhinocerotis had lost ca. 30%, and the very nutrient poor W. borbonica <10%. Litter placed under G. africana decomposed slightly faster than when placed under E. rhinocerotis. Over the course of the experiment, G. africana and E. rhinocerotis lost N and P, while W. borbonica showed strong accumulation of these elements. Decomposition rates of G. africana and E. rhinocerotis were substantially higher than those previously reported from fynbos vegetation, and variation among the species investigated was considerable. Our results suggest that fire may not always be the main factor contributing to litter breakdown and nutrient release in the fynbos biome. Thus, biological decomposition has likely been underestimated and, along with small-scale variation in ecosystem processes, would repay further study.

Effect of mean diameter and polydispersity of PLG microspheres on drug release: experiment and theory.

PubMed

Berchane, N S; Carson, K H; Rice-Ficht, A C; Andrews, M J

2007-06-07

The need to tailor release rate profiles from polymeric microspheres is a significant problem. Microsphere size, which has a significant effect on drug release rate, can potentially be varied to design a controlled drug delivery system with desired release profile. In this work the effects of microspheres mean diameter, polydispersity, and polymer degradation on drug release rate from poly(lactide-co-glycolide) (PLG) microspheres are described. Piroxicam containing PLG microspheres were fabricated at 20% loading, and at three different impeller speeds. A portion of the microspheres was then sieved giving five different size distributions. In vitro release kinetics were determined for each preparation. Based on these experimental results, a suitable mathematical theory has been developed that incorporates the effect of microsphere size distribution and polymer degradation on drug release. We show from in vitro release experiments that microsphere size has a significant effect on drug release rate. The initial release rate decreased with an increase in microsphere size. In addition, the release profile changed from first order to concave-upward (sigmoidal) as the microsphere size was increased. The mathematical model gave a good fit to the experimental release data. For highly polydisperse populations (polydispersity parameter b<3), incorporating the microsphere size distribution into the mathematical model gave a better fit to the experimental results than using the representative mean diameter. The validated mathematical model can be used to predict small-molecule drug release from PLG microsphere populations.

Effects of phosphorus supply on growth, phosphate concentration and cluster-root formation in three Lupinus species

PubMed Central

Abdolzadeh, Ahmad; Wang, Xing; Veneklaas, Erik J.; Lambers, Hans

2010-01-01

Background and Aims In some lupin species, phosphate deficiency induces cluster-root formation, which enhances P uptake by increasing root surface area and, more importantly, the release of root exudates which enhances P availability. Methods Three species of Lupinus, L. albus, L. atlanticus and L. micranthus, with inherently different relative growth rates were cultivated under hydroponics in a greenhouse at four phosphate concentrations (1, 10, 50 and 150 µm) to compare the role of internal P in regulating cluster-root formation. Key Results The highest growth rate was observed in L. atlanticus, followed by L. albus and L. micranthus. At 1 µm P, cluster-root formation was markedly induced in all three species. The highest P uptake and accumulation was observed in L. micranthus, followed by L. atlanticus and then L. albus. Inhibition of cluster-root formation was severe at 10 µm P in L. atlanticus, but occurred stepwise with increasing P concentration in the root medium in L. albus. Conclusions In L. atlanticus and L. albus cluster-root formation was suppressed by P treatments above 10 µm, indicating a P-inducible regulating system for cluster-root formation, as expected. By contrast, production of cluster roots in L. micranthus, in spite of a high internal P concentration, indicated a lower sensitivity to P status, which allowed P-toxicity symptoms to develop. PMID:20037142

Effect of Quaternary Ammonium Carboxymethylchitosan on Release Rate In-vitro of Aspirin Sustained-release Matrix Tablets

PubMed Central

Meng, Lingbin; Teng, Zhongqiu; Zheng, Nannan; Meng, Weiwei; Dai, Rongji; Deng, Yulin

2013-01-01

The aim of this study was to develop a derivative of chitosan as pharmaceutical excipient used in sustained-release matrix tablets of poorly soluble drugs. A water-soluble quaternary ammonium carboxymethylchitosan was synthesized by a two-step reaction with carboxymethylchitosan (CMCTS), decylalkyl dimethyl ammonium and epichlorohydrin. The elemental analysis showed that the target product with 10.27% of the maximum grafting degree was obtained. To assess the preliminary safety of this biopolymer, cell toxicity assay was employed. In order to further investigate quaternary ammonium carboxymethylchitosan application as pharmaceutical excipient, aspirin was chosen as model drug. The effect of quaternary ammonium CMCTS on aspirin release rate from sustained-release matrix tablets was examined by in-vitro dissolution experiments. The results showed that this biopolymer had a great potential in increasing the dissolution of poorly soluble drug. With the addition of CMCTS-CEDA, the final cumulative release rate of drug rose up to 90%. After 12 h, at the grade of 10, 20 and 50 cps, the drug release rate increased from 58.1 to 90.7%, from 64.1 to 93.9%, from 69.3 to 96.1%, respectively. At the same time, aspirin release rate from sustainedrelease model was found to be related to the amount of quaternary ammonium CMCTS employed. With the increase of CMCTS-CEDA content, the accumulated release rate increased from 69.1% to 86.7%. The mechanism of aspirin release from sustained-release matrix tablets was also preliminary studied to be Fick diffusion. These data demonstrated that the chitosan derivative has positive effect on drug release from sustained-release matrix tablets. PMID:24250627

Characterizing pollutant emissions from mosquito repellents incenses and implications in risk assessment of human health.

PubMed

Wang, Lina; Zheng, Xinran; Stevanovic, Svetlana; Xiang, Zhiyuan; Liu, Jing; Shi, Huiwen; Liu, Jing; Yu, Mingzhou; Zhu, Chun

2018-01-01

Mosquito-repellent incense is one of the most popular products used for dispelling mosquitos during summer in China. It releases large amounts of particulate and gaseous pollutants which constitute a potential hazard to human health. We conducted chamber experiment to characterize major pollutants from three types of mosquito-repellent incenses, further assessed the size-fractionated deposition in human respiratory system, and evaluated the indoor removing efficiency by fresh air. Results showed that the released pollutant concentrations were greater than permissible levels in regulations in GB3095-2012, as well as suggested by the World Health Organization (WHO). Formaldehyde accounted for 10-20% of the total amount of pollutants. Fine particles dominated in the total particulate concentrations. Geometric standard deviation (GSD) of particle number size distributions was in the range of 1.45-1.93. Count median diameter (CMD) ranged from 100 to 500 nm. Emission rates, burning rates and emission factors of both particulate and gaseous pollutants were compared and discussed. The deposition fractions in pulmonary airway from the disc solid types reached up to 52.7% of the total deposition, and the largest deposition appeared on juvenile group. Computational Fluid Dynamics (CFD) modellings indicated air-conditioner on and windows closed was the worst case. The highest concentration was 180-200 times over the standard limit. Copyright © 2017 Elsevier Ltd. All rights reserved.

Preparation and characterisation of alendronate-loaded chitosan microparticles obtained through the spray drying technique.

PubMed

Ochiuz, Lacramioara; Peris, José-Esteban

2009-03-01

Microparticles of chitosan (CHT) containing alendronate sodium (AL) were prepared in four drug:polymer ratios (1:1, 1:2, 1:4, 1:6) using the spray drying technique. The efficiency of the method was evaluated by determining production yield (about 70 %) and microencapsulation efficiency, which was almost 100 % in the case of all four of the formulations studied. Particles had a mean size of between 3.6 and 4.6 microm, and a near-spherical shape. The formulations with the highest content of AL (drug:polymer ratio 1:1 and 1:2) showed an asymmetrical distribution of particles, which were larger in size, and had a higher proportion of irregular particles than the other formulations. FT-IR analysis revealed an ionic interaction between AL and CHT. Differential scanning calorimetry and thermogravimetric analysis confirmed the microencapsulation of AL and the increased thermal stability of encapsulated AL. The dissolution profiles of AL from CHT microspheres, at pH values of 1.2 and 6.8, showed a delayed release of AL from microspheres, and the dissolution rate was dependent on the pH and the drug:polymer ratio. It can be concluded that spray drying is a suitable technique for preparing AL-loaded CHT microspheres, and that the drug:polymer ratio can be used to control the rate of AL release from microspheres.

Comparative Studies on Thermal, Mechanical, and Flame Retardant Properties of PBT Nanocomposites via Different Oxidation State Phosphorus-Containing Agents Modified Amino-CNTs.

PubMed

Zhu, San-E; Wang, Li-Li; Chen, Hao; Yang, Wei; Yuen, Anthony Chun-Yin; Chen, Timothy Bo-Yuan; Luo, Cheng; Bi, Wen-Mei; Hu, En-Zhu; Zhang, Jian; Si, Jing-Yu; Lu, Hong-Dian; Hu, Kun-Hong; Chan, Qing Nian; Yeoh, Guan Heng

2018-01-26

High-performance poly(1,4-butylene terephthalate) (PBT) nanocomposites have been developed via the consideration of phosphorus-containing agents and amino-carbon nanotube (A-CNT). One-pot functionalization method has been adopted to prepare functionalized CNTs via the reaction between A-CNT and different oxidation state phosphorus-containing agents, including chlorodiphenylphosphine (DPP-Cl), diphenylphosphinic chloride (DPP(O)-Cl), and diphenyl phosphoryl chloride (DPP(O₃)-Cl). These functionalized CNTs, DPP(O x )-A-CNTs ( x = 0, 1, 3), were, respectively, mixed with PBT to obtain the CNT-based polymer nanocomposites through a melt blending method. Scanning electron microscope observations demonstrated that DPP(O x )-A-CNT nanoadditives were homogeneously distributed within PBT matrix compared to A-CNT. The incorporation of DPP(O x )-A-CNT improved the thermal stability of PBT. Moreover, PBT/DPP(O₃)-A-CNT showed the highest crystallization temperature and tensile strength, due to the superior dispersion and interfacial interactions between DPP(O₃)-A-CNT and PBT. PBT/DPP(O)-A-CNT exhibited the best flame retardancy resulting from the excellent carbonization effect. The radicals generated from decomposed polymer were effectively trapped by DPP(O)-A-CNT, leading to the reduction of heat release rate, smoke production rate, carbon dioxide and carbon monoxide release during cone calorimeter tests.

Seed dormancy and germination of Halophila ovalis mediated by simulated seasonal temperature changes

NASA Astrophysics Data System (ADS)

Statton, John; Sellers, Robert; Dixon, Kingsley W.; Kilminster, Kieryn; Merritt, David J.; Kendrick, Gary A.

2017-11-01

The seagrass, Halophila ovalis plays an important ecological and sediment stability role in estuarine systems in Australia with the species in decline in many sites. Halophila ovalis is a facultative annual, relying mainly on recruitment from the sediment seed bank for the annual regeneration of meadows. Despite this, there is little understanding of seed dormancy releasing mechanisms and germination cues. Using H. ovalis seed from the warm temperate Swan River Estuary in Western Australia, the germination ecology of H. ovalis was investigated by simulating the natural seasonal variation in water temperatures. The proportion of germinating seeds was found to be significantly different among temperature treatments (p < 0.001). The treatment with the longest period of cold exposure at 15 °C followed by an increase in temperature to 20-25 °C (i.e. cold stratification) had the highest final mean germination of 32% and the fastest germination rate. Seeds exposed to constant mean winter temperatures of 15 °C had the slowest germination rate with less than two seeds germinating over 118 days. Thus temperature is a key germination cue for H. ovalis seeds and these data infer that cold stratification is an important dormancy releasing mechanism. This finding has implications for recruitment in facultative annual species like H. ovalis under global warming since the trend for increasing water temperatures in the region may limit seed-based recruitment in the future.

Circadian egg production by Echinostoma caproni (Digenea: Echinostomatidae) in ICR mice.

PubMed

Platt, Thomas R; Hussey, Gabrielle L; Zelmer, Derek A

2013-04-01

Circadian egg production by Echinostoma caproni was investigated in ICR mice. Four female mice were infected with 25 E. caproni metacercariae, maintained in individual cages on a 12:12 light:dark cycle, and provided food and water ad libitum. Twenty-eight, 51, and 58 days post-infection, mice were transferred to individual, wire-bottomed cages and feces were collected every 2 hr for 24 hr. The feces were weighed and processed immediately to estimate the number of eggs present. Fecal output and egg production were standardized to unit maxima for analysis. Standardized egg count and standardized fecal output followed distinctly circadian patterns and covaried. Egg production was highest from 2200 to 0200 hr and lowest from 1000 to 1800 hr. These correspond to the highest and lowest fecal production, and highest and lowest periods of host activity, respectively. Egg density (eggs/g of feces) covaried weakly with fecal output with an additional peak at 0800-1000 hr, suggesting E. caproni is responding to changes in host physiology in timing of the production and release of eggs into the intestine. The continuous production and release of eggs during the patent period, coupled with the circadian pattern of daily egg release by E. caproni , would result in the widest dispersal of eggs in the host environment and enhance transmission to the first intermediate host.

Strain Rate Dependency of Fracture Toughness, Energy Release Rate and Geomechanical Attributes of Select Indian Shales

NASA Astrophysics Data System (ADS)

Mahanta, B.; Vishal, V.; Singh, T. N.; Ranjith, P.

2016-12-01

In addition to modern improved technology, it requires detailed understanding of rock fractures for the purpose of enhanced energy extraction through hydraulic fracturing of gas shales and geothermal energy systems. The understanding of rock fracture behavior, patterns and properties such as fracture toughness; energy release rate; strength and deformation attributes during fracturing hold significance. Environmental factors like temperature, pressure, humidity, water vapor and experimental condition such as strain rate influence the estimation of these properties. In this study, the effects of strain rates on fracture toughness, energy release rate as well as geomechanical properties like uniaxial compressive strength, Young's modulus, failure strain, tensile strength, and brittleness index of gas shales were investigated. In addition to the rock-mechanical parameters, the fracture toughness and the energy release rates were measured for three different modes viz. mode I, mixed mode (I-II) and mode II. Petrographic and X-ray diffraction (XRD) analyses were performed to identify the mineral composition of the shale samples. Scanning electron microscope (SEM) analyses were conducted to have an insight about the strain rate effects on micro-structure of the rock. The results suggest that the fracture toughness; the energy release rate as well as other geomechanical properties are a function of strain rates. At high strain rates, the strength and stiffness of shale increases which in turn increases the fracture toughness and the energy release rate of shale that may be due to stress redistribution during grain fracturing. The fracture toughness and the strain energy release rates for all the modes (I/I-II/II) are comparable at lower strain rates, but they vary considerably at higher strain rates. In all the cases, mode I and mode II fracturing requires minimum and maximum applied energy, respectively. Mode I energy release rate is maximum, compared to the other modes.

Prednisolone Delivery Platforms: Capsules and Beads Combination for a Right Timing Therapy

PubMed Central

Cerciello, Andrea; Auriemma, Giulia; Morello, Silvana; Aquino, Rita P.; Del Gaudio, Pasquale

2016-01-01

In this work, a platform of alginate beads loaded with Prednisolone in hypromellose/gellan gum capsules (F6/Cps) able to delay steroidal anti-inflammatory drug (SAID) release as needed for chronotherapy of rheumatoid arthritis is proposed. Rheumatoid arthritis, showing a worsening in symptoms in the morning upon waking, is a pathology that can benefit from chronotherapy. With the aim to maximize prednisolone therapeutic action allowing the right timing of glucocorticoid therapy, different engineered microparticles (gel-beads) were manufactured using prilling (laminar jet break-up) as micro-encapsulation technique and Zn-alginate as gastroresistant carrier. Starting from various feed solutions and process parameters, the effect of the variables on particles size, morphology, solid state properties and drug release was studied. The optimization of operative and prilling/ionotropic gelation variables led to microspheres with almost spherical shape and a narrow dimensional range. The feed solution with the highest alginate (2.5% w/v) amount and drug/polymer ratio (1:5 w/w) gave rise to the highest encapsulation efficiency (78.5%) as in F6 formulation. As to drug release, F6 exhibited an interesting dissolution profile, releasing about 24% of the drug in simulated gastric fluid followed by a more sustained profile in simulated intestinal fluid. #F6, acting as a gastro-resistant and delayed release formulation, was selected for in vivo studies on male Wistar rats by means of a carrageenan-induced oedema model. Finally, this efficacious formulation was used as core material for the development of a final dosage form: F6/Cps allowed to significantly reduce prednisolone release in simulated gastric fluid (12.6%) and delayed drug release up to about 390 minutes. PMID:27472446

In Vitro Parallel Evaluation of Antibacterial Activity and Cytotoxicity of Commercially Available Silver-Containing Wound Dressings.

PubMed

Yunoki, Shunji; Kohta, Masushi; Ohyabu, Yoshimi; Iwasaki, Tetsuji

2015-01-01

This study evaluated the in vitro antibacterial activity and cytotoxicity of various commercially available silver-containing dressings (Ag dressing). Biohesive Ag (hydrocolloid, silver sulfadiazine), Aquacel® Ag (nonwoven fabric, ionic silver [Ag]), Algisite™ Ag (nonwoven fabric, Ag), Mepilex® Ag (foam, silver sulfate), and PolyMem® Ag (foam, nanocrystalline silver) were tested for characteristics of Ag release, antibacterial activity, and cytotoxicity. The release of Ag was investigated in cell culture medium at immersion periods of 6, 24, and 48 hours. The antibacterial activity against Staphylococcus aureus and Pseudomonas aeruginosa were accessed by a disc diffusion test. The cytotoxicity was evaluated using V79 cells, by an extraction method. The cytotoxicity was not a monotonic function of the antibacterial activity among the Ag dressings and could not be simply explained by Ag-release properties. Biohesive Ag was regarded as a slow-release Ag dressing, showing the lowest cytotoxicity, while the antibacterial activity was classified as "strong" or "significant" against the two species of bacteria. Aquacel Ag and Algisite Ag showed higher antibacterial activity and cytotoxic effects, which were supported by the higher Ag release. Mepilex Ag showed the highest release of Ag, and the cytotoxicity was the highest among the Ag dressings. However, the antibacterial activity was classified as "significant" or "no activity" for P. aeruginosa and S. aureus, respectively. PolyMem Ag showed the lowest Ag release, and the antibacterial activity classified as "significant" or "no activity" for S. aureus and P. aeruginosa, respectively, whereas the cytotoxicity was similar to those of Aquacel Ag and Algisite Ag. The efficacy and adverse effects of the Ag dressings revealed differences that should be considered by clinicians during wound management.

Hindered disulfide bonds to regulate release rate of model drug from mesoporous silica.

PubMed

Nadrah, Peter; Maver, Uroš; Jemec, Anita; Tišler, Tatjana; Bele, Marjan; Dražić, Goran; Benčina, Mojca; Pintar, Albin; Planinšek, Odon; Gaberšček, Miran

2013-05-01

With the advancement of drug delivery systems based on mesoporous silica nanoparticles (MSNs), a simple and efficient method regulating the drug release kinetics is needed. We developed redox-responsive release systems with three levels of hindrance around the disulfide bond. A model drug (rhodamine B dye) was loaded into MSNs' mesoporous voids. The pore opening was capped with β-cyclodextrin in order to prevent leakage of drug. Indeed, in absence of a reducing agent the systems exhibited little leakage, while the addition of dithiothreitol cleaved the disulfide bonds and enabled the release of cargo. The release rate and the amount of released dye were tuned by the level of hindrance around disulfide bonds, with the increased hindrance causing a decrease in the release rate as well as in the amount of released drug. Thus, we demonstrated the ability of the present mesoporous systems to intrinsically control the release rate and the amount of the released cargo by only minor structural variations. Furthermore, an in vivo experiment on zebrafish confirmed that the present model delivery system is nonteratogenic.

Release from or through a wax matrix system. I. Basic release properties of the wax matrix system.

PubMed

Yonezawa, Y; Ishida, S; Sunada, H

2001-11-01

Release properties from a wax matrix tablet was examined. To obtain basic release properties, the wax matrix tablet was prepared from a physical mixture of drug and wax powder (hydrogenated caster oil) at a fixed mixing ratio. Properties of release from the single flat-faced surface or curved side surface of the wax matrix tablet were examined. The applicability of the square-root time law and of Higuchi equations was confirmed. The release rate constant obtained as g/min(1/2) changed with the release direction. However, the release rate constant obtained as g/cm2 x min(1/2) was almost the same. Hence it was suggested that the release property was almost the same and the wax matrix structure was uniform independent of release surface or direction at a fixed mixing ratio. However, these equations could not explain the entire release process. The applicability of a semilogarithmic equation was not as good compared with the square-root time law or Higuchi equation. However, it was revealed that the semilogarithmic equation was available to simulate the entire release process, even though the fit was somewhat poor. Hence it was suggested that the semilogarithmic equation was sufficient to describe the release process. The release rate constant was varied with release direction. However, these release rate constants were expressed by a function of the effective surface area and initial amount, independent of the release direction.

Reconviction and revocation rates in Flanders after medium security treatment.

PubMed

Jeandarme, Inge; Habets, Petra; Oei, T I; Bogaerts, Stefan

2016-01-01

To examine the criminal outcome of Flemish forensic psychiatric patients ('internees') after medium security treatment. Also, the effect of conditional release on recidivism of two subgroups (internees under conditional release and internees who received unconditional release) was examined. Reconviction rates and revocation rates were collected for all participants. Kaplan-Meier survival analyses were used to investigate recidivism rates while controlling for time at risk. During the 10-year period, 502 offenders were discharged from medium security treatment. Over a follow-up period averaging 3.6years, 7.4% of discharged patients were reconvicted or received a new 'not guilty by reason of insanity' (NGRI) verdict for a violent offence. One-quarter of the population had their conditional release revoked. Part of the study population was granted unconditional release. Reconviction rates were higher after unconditional release in comparison to conditional release. The results of this study suggest that the court supervision of NGRI patients in Flanders is effective in protecting the community from further offending. Copyright © 2016 Elsevier Ltd. All rights reserved.

Development of extended release dosage forms using non-uniform drug distribution techniques.

PubMed

Huang, Kuo-Kuang; Wang, Da-Peng; Meng, Chung-Ling

2002-05-01

Development of an extended release oral dosage form for nifedipine using the non-uniform drug distribution matrix method was conducted. The process conducted in a fluid bed processing unit was optimized by controlling the concentration gradient of nifedipine in the coating solution and the spray rate applied to the non-pareil beads. The concentration of nifedipine in the coating was controlled by instantaneous dilutions of coating solution with polymer dispersion transported from another reservoir into the coating solution at a controlled rate. The USP dissolution method equipped with paddles at 100 rpm in 0.1 N hydrochloric acid solution maintained at 37 degrees C was used for the evaluation of release rate characteristics. Results indicated that (1) an increase in the ethyl cellulose content in the coated beads decreased the nifedipine release rate, (2) incorporation of water-soluble sucrose into the formulation increased the release rate of nifedipine, and (3) adjustment of the spray coating solution and the transport rate of polymer dispersion could achieve a dosage form with a zero-order release rate. Since zero-order release rate and constant plasma concentration were achieved in this study using the non-uniform drug distribution technique, further studies to determine in vivo/in vitro correlation with various non-uniform drug distribution dosage forms will be conducted.

Interaction between fed gastric media (Ensure Plus®) and different hypromellose based caffeine controlled release tablets: comparison and mechanistic study of caffeine release in fed and fasted media versus water using the USP dissolution apparatus 3.

PubMed

Franek, Frans; Holm, Per; Larsen, Frank; Steffansen, Bente

2014-01-30

The aim of the study was to investigate caffeine release in fed and fasted state media from three controlled release matrix tablets containing different HPMC viscosity grades. The biorelevant in vitro dissolution methods utilize the USP 3 dissolution apparatus and biorelevant media to simulate fed and fasted gastro-intestinal dissolution conditions. The effect of tablet reciprocation rate (dip speed) in dissolution media (10 and 15 dips per minute) and media (water, fed and fasted) on caffeine release rate from - and erosion rate of - 100, 4000 and 15,000 mPa s HPMC viscosity tablets was investigated using factorial designed experiments. Furthermore, the mechanism of release in Ensure Plus(®), a nutrition drink similar in composition to the FDA standard meal, was investigated by studying tablet swelling using texture analysis. Altering dip speed has negligible effect on release and erosion rates. Using fasted media instead of water slightly decreases caffeine release from 100 and 4000 mPa s HPMC viscosity tablets as well as erosion rates, while 15,000 mPa s tablets remain unaffected. Fed compared to fasted media decreases caffeine release rate, and the food effect is greater for the 100 mPa s viscosity tablets compared to the 4000 and 15,000 mPa s viscosity tablets. The investigation using texture analysis indicates that Ensure Plus(®) becomes rate-limiting for caffeine release from HPMC tablets by forming a hydrophobic barrier around the tablets. The barrier decreases tablet water permeation, which decreases erosion rate in 100 mPa s viscosity tablets, swelling in 15,000 mPa s viscosity tablets and caffeine release from both tablets. This observed interaction between Ensure Plus(®) and the HPMC tablets may translate into decreased drug release rate in the fed stomach, which may decrease the amount of drug available for absorption in the small intestine and thus reduce systemic drug exposure and maximum plasma concentration. Copyright © 2013 Elsevier B.V. All rights reserved.

Benthic metabolism over the emersion - immersion alternation in sands colonized by the invasive Manila clam Ruditapes philippinarum

NASA Astrophysics Data System (ADS)

Migné, Aline; Trigui, Rima Jihane; Davoult, Dominique; Desroy, Nicolas

2018-01-01

The effect of an invasive infaunal suspension-feeding bivalve, the Manila clam Ruditapes philippinarum, on benthic inorganic carbon and nutrient fluxes was examined through in situ incubations. Measurements were performed in spring and summer on a tidal sandflat of the Rance estuary (south part of the Western English Channel) colonized by the Manila clam after its deliberate introduction in the 1990's. Benthic inorganic carbon fluxes were measured using light and dark benthic chambers both at emersion and immersion. Benthic nutrient fluxes were measured using dark benthic chambers at immersion. Inorganic carbon (IC) and ammonium sediment release under darkness at immersion reached 5.60 mmol m-2 h-1 and 441 μmol m-2 h-1 respectively for a clam density of 291 ind m-2. The sediment IC-release under darkness was lower during emersion than during immersion, probably due to the reduced activity of infauna at low tide. Under ambient light, a sediment IC-uptake was systematically measured at emersion, indicating a net autotrophy under the condition of measurements (125 < surface PAR < 1670 μmol m-2 s-1), while either sediment IC-uptake or release was measured at immersion according to light variation (20 < underwater PAR < 990 μmol m-2 s-1). The highest gross community primary production, calculated from highest IC-fluxes at light (i.e. net community production) and highest IC-fluxes at dark (i.e. community respiration), was similar at emersion and immersion and reached 6.2 mmolC m-2 h-1. These results suggest that the metabolic activity of the invasive Manila clam Ruditapes philippinarum contributes to increase inorganic C and ammonium sediment release. These regenerated nutrients may support microphytobenthic production which appeared particularly high on this intertidal sand flat.

Elevational change in woody tissue CO2 efflux in a tropical mountain rain forest in southern Ecuador.

PubMed

Zach, Alexandra; Horna, Viviana; Leuschner, Christoph

2008-01-01

Much uncertainty exists about the magnitude of woody tissue respiration and its environmental control in highly diverse tropical moist forests. In a tropical mountain rain forest in southern Ecuador, we measured the apparent diurnal gas exchange of stems and coarse roots (diameter 1-4 cm) of trees from representative families along an elevational transect with plots at 1050, 1890 and 3050 m a.s.l. Mean air temperatures were 20.8, 17.2 and 10.6 degrees C, respectively. Stem and root CO(2) efflux of 13 to 21 trees per stand from dominant families were investigated with an open gas exchange system while stand microclimate was continuously monitored. Substantial variation in respiratory activity among and within species was found at all sites. Mean daily CO(2) release rates from stems declined 6.6-fold from 1.38 micromol m(-2) s(-1) at 1050 m to 0.21 micromol m(-2) s(-1) at 3050 m. Mean daily CO(2) release from coarse roots decreased from 0.35 to 0.20 micromol m(-2) s(-1) with altitude, but the differences were not significant. There was, thus, a remarkable shift from a high ratio of stem to coarse root respiration rates at the lowest elevation to an apparent equivalence of stem and coarse root CO(2) efflux rates at the highest elevation. We conclude that stem respiration, but not root respiration, greatly decreases with elevation in this transect, coinciding with a substantial decrease in relative stem diameter increment and a large increase in fine and coarse root biomass production with elevation.

Decreased diversion by doctor-shopping for a reformulated extended release oxycodone product (OxyContin).

PubMed

Chilcoat, Howard D; Coplan, Paul M; Harikrishnan, Venkatesh; Alexander, Louis

2016-08-01

Doctor-shopping (obtaining prescriptions from multiple prescribers/pharmacies) for opioid analgesics produces a supply for diversion and abuse, and represents a major public health issue. An open cohort study assessed changes in doctor-shopping in the U.S. for a brand extended release (ER) oxycodone product (OxyContin) and comparator opioids before (July, 2009 to June, 2010) versus after (January, 2011 to June, 2013) introduction of reformulated brand ER oxycodone with abuse-deterrent properties, using IMS LRx longitudinal data covering >150 million patients and 65% of retail U.S. prescriptions. After its reformulation, the rate of doctor-shopping decreased 50% (for 2+ prescribers/3+ pharmacies) for brand ER oxycodone, but not for comparators. The largest decreases in rates occurred among young adults (73%), those paying with cash (61%) and those receiving the highest available dose (62%), with a 90% decrease when stratifying by all three characteristics. The magnitude of doctor-shopping reductions increased with increasing number of prescribers/pharmacies (e.g., 75% reduction for ≥2 prescribers/≥4 pharmacies). The rate of doctor-shopping for brand ER oxycodone decreased substantially after its reformulation, which did not occur for other prescription opioids. The largest reductions in doctor-shopping occurred with characteristics associated with higher abuse risk such as youth, cash payment and high dose, and with more specific thresholds of doctor-shopping. A higher prescriber and/or pharmacy threshold also increased the magnitude of the decrease, suggesting that it better captured the effect of the reformulation on actual doctor-shoppers. Copyright © 2016 The Authors. Published by Elsevier Ireland Ltd.. All rights reserved.

Residual thermal and moisture influences on the strain energy release rate analysis of edge delamination

NASA Technical Reports Server (NTRS)

Obrien, T. K.; Raju, I. S.; Garber, D. P.

1985-01-01

A laminated plate theory analysis is developed to calculate the strain energy release rate associated with edge delamination growth in a composite laminate. The analysis includes the contribution of residual thermal and moisture stresses to the strain energy released. The strain energy release rate, G, increased when residual thermal effects were combined with applied mechanical strains, but then decreased when increasing moisture content was included. A quasi-three-dimensional finite element analysis indicated identical trends and demonstrated these same trends for the individual strain energy release rate components, G sub I and G sub II, associated with interlaminar tension and shear. An experimental study indicated that for T300/5208 graphite-epoxy composites, the inclusion of residual thermal and moisture stresses did not significantly alter the calculation of interlaminar fracture toughness from strain energy release rate analysis of edge delamination data taken at room temperature, ambient conditions.

Quantification of Energy Release in Composite Structures

NASA Technical Reports Server (NTRS)

Minnetyan, Levon

2003-01-01

Energy release rate is usually suggested as a quantifier for assessing structural damage tolerance. Computational prediction of energy release rate is based on composite mechanics with micro-stress level damage assessment, finite element structural analysis and damage progression tracking modules. This report examines several issues associated with energy release rates in composite structures as follows: Chapter I demonstrates computational simulation of an adhesively bonded composite joint and validates the computed energy release rates by comparison with acoustic emission signals in the overall sense. Chapter II investigates the effect of crack plane orientation with respect to fiber direction on the energy release rates. Chapter III quantifies the effects of contiguous constraint plies on the residual stiffness of a 90 ply subjected to transverse tensile fractures. Chapter IV compares ICAN and ICAN/JAVA solutions of composites. Chapter V examines the effects of composite structural geometry and boundary conditions on damage progression characteristics.

Quantification of Energy Release in Composite Structures

NASA Technical Reports Server (NTRS)

Minnetyan, Levon; Chamis, Christos C. (Technical Monitor)

2003-01-01

Energy release rate is usually suggested as a quantifier for assessing structural damage tolerance. Computational prediction of energy release rate is based on composite mechanics with micro-stress level damage assessment, finite element structural analysis and damage progression tracking modules. This report examines several issues associated with energy release rates in composite structures as follows: Chapter I demonstrates computational simulation of an adhesively bonded composite joint and validates the computed energy release rates by comparison with acoustic emission signals in the overall sense. Chapter II investigates the effect of crack plane orientation with respect to fiber direction on the energy release rates. Chapter III quantifies the effects of contiguous constraint plies on the residual stiffness of a 90 deg ply subjected to transverse tensile fractures. Chapter IV compares ICAN and ICAN/JAVA solutions of composites. Chapter V examines the effects of composite structural geometry and boundary conditions on damage progression characteristics.

Controlling the Release of Indomethacin from Glass Solutions Layered with a Rate Controlling Membrane Using Fluid-Bed Processing. Part 2: The Influence of Formulation Parameters on Drug Release.

PubMed

Dereymaker, Aswin; Pelgrims, Jirka; Engelen, Frederik; Adriaensens, Peter; Van den Mooter, Guy

2017-04-03

This study aimed to investigate the pharmaceutical performance of an indomethacin-polyvinylpyrrolidone (PVP) glass solution applied using fluid bed processing as a layer on inert sucrose spheres and subsequently top-coated with a release rate controlling membrane consisting of either ethyl cellulose or Eudragit RL. The implications of the addition of a pore former (PVP) and the coating medium (ethanol or water) on the diffusion and release behavior were also considered. In addition, the role of a charge interaction between drug and controlled release polymer on the release was investigated. Diffusion experiments pointed to the influence of pore former concentration, rate controlling polymer type, and coating solvent on the permeability of the controlled release membranes. This can be translated to drug release tests, which show the potential of diffusion tests as a preliminary screening test and that diffusion is the main factor influencing release. Drug release tests also showed the effect of coating layer thickness. A charge interaction between INDO and ERL was demonstrated, but this had no negative effect on drug release. The higher diffusion and release observed in ERL-based rate controlling membranes was explained by a higher hydrophilicity, compared to EC.

CIDR

Science.gov Websites

Statistics Quality Control Statistics CIDR is dedicated to producing the highest quality data for our investigators. These cumulative quality control statistics are based on data from 419 released CIDR Program

77 FR 47918 - Information Collection Activities (Released Rates)

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-10

... decision in Released Rates of Motor Common Carriers of Household Goods, Docket No. RR 999 (Amendment No. 5... loss or damage that occurs during interstate household-good moves. See Safe, Accountable, Flexible... elects anything other than full-value protection. See Released Rates of Motor Common Carriers of...

High speed 2-dimensional temperature measurements of nanothermite composites: Probing thermal vs. Gas generation effects

NASA Astrophysics Data System (ADS)

Jacob, Rohit J.; Kline, Dylan J.; Zachariah, Michael R.

2018-03-01

This work investigates the reaction dynamics of metastable intermolecular composites through high speed spectrometry, pressure measurements, and high-speed color camera pyrometry. Eight mixtures including Al/CuO and Al/Fe2O3/xWO3 (x being the oxidizer mol. %) were reacted in a constant volume pressure cell as a means of tuning gas release and adiabatic temperature. A direct correlation between gas release, peak pressure, and pressurization rate was observed, but it did not correlate with temperature. When WO3 was varied as part of the stoichiometric oxidizer content, it was found that Al/Fe2O3/70% WO3 achieved the highest pressures and shortest burn time despite a fairly constant temperature between mixtures, suggesting an interplay between the endothermic Fe2O3 decomposition and the higher adiabatic flame temperature sustained by the Al/WO3 reaction in the composite. It is proposed that the lower ignition temperature of Al/WO3 leads to the initiation of the composite and its higher flame temperature enhances the gasification of Fe2O3, thus improving advection and propagation as part of a feedback loop that drives the reaction. Direct evidence of such gas release promoting reactivity was obtained through high speed pyrometry videos of the reaction. These results set the stage for nanoenergetic materials that can be tuned for specific applications through carefully chosen oxidizer mixtures.

Effect of Alcohol on Diesel Engine Combustion Operating with Biodiesel-Diesel Blend at Idling Conditions

NASA Astrophysics Data System (ADS)

Mahmudul, H. M.; Hagos, Ftwi. Y.; A, M. Mukhtar N.; Mamat, Rizalman; Abdullah, A. Adam

2018-03-01

Biodiesel is a promising alternative fuel to run the automotive engine. However, its blends have not been properly investigated during idling as it is the main problem to run the vehicles in a big city. The purpose of this study is to evaluate the impact of alcohol additives such as butanol and ethanol on combustion parameters under idling conditions when a single cylinder diesel engine operates with diesel, diesel-biodiesel blends, and diesel biodiesel-alcohol blends. The engine combustion parameters such as peak pressure, heat release rate and ignition delay were computed. This investigation has revealed that alcohol blends with diesel and biodiesel, BU20 blend yield higher maximum peak cylinder pressure than diesel. B5 blend was found with the lowest energy release among all. B20 was slightly lower than diesel. BU20 blend was seen with the highest peak energy release where E20 blend was found advance than diesel. Among all, the blends alcohol component revealed shorter ignition delay. B5 and B20 blends were influenced by biodiesel interference and the burning fraction were found slightly slower than conventional diesel where BU20 and E20 blends was found slightly faster than diesel So, based on the result, it can be said that among the alcohol blends butanol and ethanol can be promising alternative at idling conditions and can be used without any engine modifications.

Comparison of short-term in vitro fluoride release and recharge from four different types of pit-and-fissure sealants.

PubMed

Koga, Hiroshi; Kameyama, Atsushi; Matsukubo, Takashi; Hirai, Yoshito; Takaesu, Yoshinori

2004-08-01

The purpose of this in vitro study was to assess the effects of four commercial fluoride-containing pit-and-fissure sealants on caries prevention. Four sealants containing fluoride, Fuji III, Fuji III LC (GC Co., Tokyo), Teethmate F-1 (Kuraray Medical Co., Osaka) and Helioseal F (Vivadent Co., Liechtenstein) were used to investigate fluoride release and recharge. Disk-shaped specimens prepared from each material were immersed in distilled water at a temperature of 37 degrees C. After seven days, acidulated phosphate fluoride solution (APF) was applied to each specimen, and it was then again immersed in distilled water for 14 days. We then determined how much fluoride had been released into the immersing water. Fuji III LC was used with APF solution to investigate the fluoride uptake. Fuji III had the highest fluoride release, and Fuji III LC had the highest fluoride recharge. Helioseal F and Teethmate F-1 had almost no fluoride recharge. Fuji III LC/APF had a higher fluoride uptake to enamel than Fuji III LC. These results suggest that GIC-sealants in the oral cavity can serve as a fluoride reservoir and contribute to retaining a low fluoride level in oral fluids, thereby preventing caries.

Effects of density on growth, metamorphosis, and survivorship in tadpoles of Scaphiopus holbrooki

DOE Office of Scientific and Technical Information (OSTI.GOV)

Semlitsch, R.D.; Caldwell, J.P.

1982-08-01

Density-dependent aspects of growth, metamorphosis, and survivorship of Scaphiopus holbrooki tadpoles were examined in the laboratory under two experimental regimes. In the first density experiment, the growth index (W) of tadpoles decreased exponentially with density. Mean growth rate varied from 0.023 mL/d at the lowest density to 0.006 mL/d at the highest density. The mean number of days to metamorphic climax was positively associated with the initial density treatment: 27 d at the lowest density to 86 d at the highest density. The body size of tadpoles at metamorphosis showed a concave curvilinear relationship to initial density, indicating tadpoles atmore » the highest densities are apparently capable to growth recovery once released from density stress. The survival of tadpoles decreased exponentially with initial density, from 90% at the lowest density to 20% at the highest initial density. In the second experiment a cross-classified design was used to examine the effects of density and duration of treatment (time) on growth and metamorphosis. Density and time had significant effects on body size at metamorphosis and days to metamorphosis. There was no significant interaction between density and time. These results indicate that the inhibitory effect of density stress varies with the duration of the stress. Scaphiopus holbrooki tadpoles exhibit developmental traits (rapid growth, short larval period, small body size at metamorphosis) that should be favored by natural selection in high density habitats. Dispersability may be a mechanism whereby S. holbrooki can minimize the detrimental effects of density stress.« less

Expert assessment of vulnerability of permafrost carbon to climate change

USGS Publications Warehouse

Schuur, E.A.G.; Abbott, B.W.; Bowden, W.B.; Brovkin, V.; Camill, P.; Canadell, J.G.; Chanton, J.P.; Chapin, F. S.; Christensen, T.R.; Ciais, P.; Crosby, B.T.; Czimczik, C.I.; Grosse, G.; Harden, J.; Hayes, D.J.; Hugelius, G.; Jastrow, J.D.; Jones, J.B.; Kleinen, T.; Koven, C.D.; Krinner, G.; Kuhry, P.; Lawrence, D.M.; McGuire, A.D.; Natali, Susan M.; O'Donnell, J. A.; Ping, C.-L.; Riley, W.J.; Rinke, A.; Romanovsky, V.E.; Sannel, A.B.K.; Schädel, C.; Schaefer, K.; Sky, J.; Subin, Z.M.; Tarnocai, C.; Turetsky, M.R.; Waldrop, M.P.; Anthony, K.M. Walter; Wickland, K.P.; Wilson, C.J.; Zimov, S.A.

2013-01-01

Approximately 1700 Pg of soil carbon (C) are stored in the northern circumpolar permafrost zone, more than twice as much C than in the atmosphere. The overall amount, rate, and form of C released to the atmosphere in a warmer world will influence the strength of the permafrost C feedback to climate change. We used a survey to quantify variability in the perception of the vulnerability of permafrost C to climate change. Experts were asked to provide quantitative estimates of permafrost change in response to four scenarios of warming. For the highest warming scenario (RCP 8.5), experts hypothesized that C release from permafrost zone soils could be 19–45 Pg C by 2040, 162–288 Pg C by 2100, and 381–616 Pg C by 2300 in CO2 equivalent using 100-year CH4 global warming potential (GWP). These values become 50 % larger using 20-year CH4 GWP, with a third to a half of expected climate forcing coming from CH4 even though CH4 was only 2.3 % of the expected C release. Experts projected that two-thirds of this release could be avoided under the lowest warming scenario (RCP 2.6). These results highlight the potential risk from permafrost thaw and serve to frame a hypothesis about the magnitude of this feedback to climate change. However, the level of emissions proposed here are unlikely to overshadow the impact of fossil fuel burning, which will continue to be the main source of C emissions and climate forcing.

Expert assessment of vulnerability of permafrost carbon to climate change

DOE PAGES

Schuur, E. A. G.; Abbott, B. W.; Bowden, W. B.; ...

2013-03-26

Approximately 1700 Pg of soil carbon (C) are stored in the northern circumpolar permafrost zone, more than twice as much C than in the atmosphere. The overall amount, rate, and form of C released to the atmosphere in a warmer world will influence the strength of the permafrost C feedback to climate change. We used a survey to quantify variability in the perception of the vulnerability of permafrost C to climate change. Experts were asked to provide quantitative estimates of permafrost change in response to four scenarios of warming. For the highest warming scenario (RCP 8.5), experts hypothesized that Cmore » release from permafrost zone soils could be 19–45 Pg C by 2040, 162–288 Pg C by 2100, and 381–616 Pg C by 2300 in CO 2 equivalent using 100-year CH 4 global warming potential (GWP). These values become 50% larger using 20-year CH 4 GWP, with a third to a half of expected climate forcing coming from CH 4 even though CH 4 was only 2.3 % of the expected C release. Experts projected that two-thirds of this release could be avoided under the lowest warming scenario (RCP 2.6). These results highlight the potential risk from permafrost thaw and serve to frame a hypothesis about the magnitude of this feedback to climate change. However, the level of emissions proposed here are unlikely to overshadow the impact of fossil fuel burning, which will continue to be the main source of C emissions and climate forcing.« less

Dextran-coated superparamagnetic nanoparticles as potential cancer drug carriers in vivo

NASA Astrophysics Data System (ADS)

Peng, Mingli; Li, Houli; Luo, Zhiyi; Kong, Jian; Wan, Yinsheng; Zheng, Lemin; Zhang, Qinlu; Niu, Hongxin; Vermorken, Alphons; van de Ven, Wim; Chen, Chao; Zhang, Xikun; Li, Fuqiang; Guo, Lili; Cui, Yali

2015-06-01

Dextran-coated superparamagnetic iron oxide nanoparticles (DSPIONs) have gained considerable interest, because of their biocompatibility and biosafety in clinics. Doxorubicin (Dox), a widely used chemotherapeutic drug, always has limited applications in clinical therapy due to its serious side effects of dose-limiting irreversible cardiotoxicity and myelo suppression. Herein, DSPIONs were synthesized and developed as magnetic carriers for doxorubicin. The Dox-DSPION conjugates were evaluated in the in vitro test of Dox release, which showed pH-dependence with the highest release percentage of 50.3% at pH 5.0 and the lowest release percentage of 11.8% in a physiological environment. The cytotoxicity of DSPIONs and Dox-DSPIONs evaluated by the MTT assay indicated that DSPIONs had no cytotoxicity and the conjugates had significantly reduced the toxicity (IC50 = 1.36 μg mL-1) compared to free Dox (IC50 = 0.533 μg mL-1). Furthermore, confocal microscopic data of cell uptake suggest that less cytotoxicity of Dox-DSPIONs may be attributed to the cellular internalization of the conjugates and sustainable release of Dox from the formulation in the cytoplasm. More importantly, the results from the rabbit VX2 liver tumor model test under an external magnetic field showed that the conjugates had approximately twice the anti-tumor activity and two and a half times the animal survival rate, respectively, compared to free Dox. Collectively, our data have demonstrated that Dox-DSPIONs have less toxicity with better antitumor effectiveness in in vitro and in vivo applications, suggesting that the conjugates have potential to be developed into chemo-therapeutic formulations.

Syngas formation in methane flames and carbon monoxide release during quenching

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weinberg, Felix; Carleton, Fred; Houdmont, Raphael

Following a recent investigation into chemi-ionization and chemiluminescence during gradual aeration of small, laminar methane flames, we proposed that partial oxidation products, or syngas constituents, formed in the pre-flame zone well below the luminous region, were responsible for the observed effects. We therefore map temperature, CO, and H{sub 2} for geometries and conditions relevant to burners in domestic boiler systems, to assess the potential hazard of CO release into the ambient atmosphere, should any partial quenching occur. CO concentrations peaks of 5.5 volume % are recorded in the core surrounding the axis. Appreciable CO concentrations are also found in themore » absence of added air. Experiments on various burner port geometries and temperatures suggest that this is not due to air entrainment at the flame base but to diffusion from zones closer to the flame. Next, quenching surfaces such as grids, perforated plates and flame trap matrices of different metals are progressively lowered into the flame. To avoid flow line distortion, suction aspirates the quenched products. The highest emission rate occurs with the quenching plane some 4 mm above the burner; further lowering of the quenching surface causes flame extinction. The maximum CO release is close to converting 10% of the CH{sub 4} feed, with some variation with quenching material. Expressing this potential release in terms of, e.g. boiler power, predicts a potentially serious hazard. Results of numerical simulations adequately parallel the experimental sampling profiles and provide insights into local concentrations, as well as the spatially resolved CO flux, which is calculated for a parabolic inlet flow profile. Integration across the stream implies, on the basis of the simulation, a possible tripling of the experimental CO release, were quenching simply to release the local gas composition into the atmosphere. Comparison with experiment suggests some chemical interaction with the quenching surface. (author)« less

Measurement of semiochemical release rates with a dedicated environmental control system

Treesearch

Heping Zhu; Harold W. Thistle; Christopher M. Ranger; Hongping Zhou; Brian L. Strom

2015-01-01

Insect semiochemical dispensers are commonly deployed under variable environmental conditions over a specified period. Predictions of their longevity are hampered by a lack of methods to accurately monitor and predict how primary variables affect semiochemical release rate. A system was constructed to precisely determine semiochemical release rates under...

40 CFR 302.8 - Continuous releases.

Code of Federal Regulations, 2010 CFR

2010-07-01

... that the release is continuous and stable in quantity and rate; (2) Change in the normal range. If... section, continuous and stable in quantity and rate. (b) Definitions. The following definitions apply to... conditions during the preceding year. Only releases that are both continuous and stable in quantity and rate...

Miniature bulge test and energy release rate in HIPed aluminum/aluminum interfacial fracture

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, C.; Lovato, M. L.; Clarke, K. D.

We summarize the development of a technique of using miniature bulge test combined with three-dimensional digital image correlation (3D-DIC) for measuring energy release rate or fracture toughness of bimaterial interface of thin metal foils. Furthermore, the energy release rate associated with the HIPed aluminum/aluminum interfacial delamination is determined experimentally using the proposed technique. Detailed discussions of the schemes of preparing and conducting the bulge test, and computing various quantities required for the determination of the energy release rate are presented.

Miniature bulge test and energy release rate in HIPed aluminum/aluminum interfacial fracture

DOE PAGES

Liu, C.; Lovato, M. L.; Clarke, K. D.; ...

2017-10-13

We summarize the development of a technique of using miniature bulge test combined with three-dimensional digital image correlation (3D-DIC) for measuring energy release rate or fracture toughness of bimaterial interface of thin metal foils. Furthermore, the energy release rate associated with the HIPed aluminum/aluminum interfacial delamination is determined experimentally using the proposed technique. Detailed discussions of the schemes of preparing and conducting the bulge test, and computing various quantities required for the determination of the energy release rate are presented.

Rates of zinc and trace metal release from dissolving sphalerite at pH 2.0-4.0

USGS Publications Warehouse

Stanton, M.R.; Gemery-Hill, P. A.; Shanks, Wayne C.; Taylor, C.D.

2008-01-01

High-Fe and low-Fe sphalerite samples were reacted under controlled pH conditions to determine nonoxidative rates of release of Zn and trace metals from the solid-phase. The release (solubilization) of trace metals from dissolving sphalerite to the aqueous phase can be characterized by a kinetic distribution coefficient, (Dtr), which is defined as [(Rtr/X(tr)Sph)/(RZn/X(Zn) Sph)], where R is the trace metal or Zn release rate, and X is the mole fraction of the trace metal or Zn in sphalerite. This coefficient describes the relationship of the sphalerite dissolution rate to the trace metal mole fraction in the solid and its aqueous concentration. The distribution was used to determine some controls on metal release during the dissolution of sphalerite. Departures from the ideal Dtr of 1.0 suggest that some trace metals may be released via different pathways or that other processes (e.g., adsorption, solubility of trace minerals such as galena) affect the observed concentration of metals. Nonoxidative sphalerite dissolution (mediated by H+) is characterized by a "fast" stage in the first 24-30 h, followed by a "slow" stage for the remainder of the reaction. Over the pH range 2.0-4.0, and for similar extent of reaction (reaction time), sphalerite composition, and surface area, the rates of release of Zn, Fe, Cd, Cu, Mn and Pb from sphalerite generally increase with lower pH. Zinc and Fe exhibit the fastest rates of release, Mn and Pb have intermediate rates of release, and Cd and Cu show the slowest rates of release. The largest variations in metal release rates occur at pH 2.0. At pH 3.0 and 4.0, release rates show less variation and appear less dependent on the metal abundance in the solid. For the same extent of reaction (100 h), rates of Zn release range from 1.53 ?? 10-11 to 5.72 ?? 10-10 mol/m2/s; for Fe, the range is from 4.59 ?? 10-13 to 1.99 ?? 10-10 mol/m2/s. Trace metal release rates are generally 1-5 orders of magnitude slower than the Zn or Fe rates. Results indicate that the distributions of Fe and Cd are directly related to the rate of sphalerite dissolution throughout the reaction at pH 3.0 and 4.0 because these two elements substitute readily into sphalerite. These two metals are likely to be more amenable to usage in predictive acid dissolution models because of this behavior. The Pb distribution shows no strong relation to sphalerite dissolution and appears to be controlled by pH-dependent solubility, most likely related to trace amounts of galena. The distribution of Cu is similar to that of Fe but is the most-dependent of all metals on its mole fraction ratio (Zn:Cu) in sphalerite. The Mn distributions suggest an increase in the rate of Mn release relative to sphalerite dissolution occurs in low Mn samples as pH increases. The Mn distribution in high Mn samples is nearly independent of pH and sphalerite dissolution at pH 2.0 but shows a dependence on these two parameters at higher pH (3.0-4.0).

Investigation on formaldehyde release from preservatives in cosmetics.

PubMed

Lv, C; Hou, J; Xie, W; Cheng, H

2015-10-01

To understand formaldehyde residue in cosmetics, an investigation on formaldehyde release from eight preservatives (methenamine - MA, paraformaldehyde - PF, poly(p-toluenesulfonamide-co-formaldehyde) -PTSAF, quaternium-15 - QU, imidazolidinyl urea - IU, diazolidinyl urea - DU, dimethyloldimethyl hydantoin - DMDM and bronopol - BP) under various conditions was performed. The concentration of released formaldehyde was determined by high-performance liquid chromatography with photodiode array detection after derivatization with 2,4-dinitrophenylhydrazine. The amounts of formaldehyde release were in the order of PF > DU > DMDM ≈ QU ≈ IU > MA > BP > PTSAF. The releasing amounts of formaldehyde were the highest in the presence of aqueous matrices for the releasers except QU and IU, and the releasing effect was also relative to pH. More formaldehyde was released with longer storage time and higher temperature. Furthermore, all preservatives in cosmetic matrices released fewer amounts of formaldehyde than in pure aqueous or organic matrices, and the formaldehyde-releasing amounts were also cosmetic specific. Formaldehyde release was dependent on the matrix, pH, time and mainly temperature, and the releasing effect was also cosmetic specific. © 2015 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

A novel bio electro active alginate-aniline tetramer/ agarose scaffold for tissue engineering: synthesis, characterization, drug release and cell culture study.

PubMed

Atoufi, Zhale; Zarrintaj, Payam; Motlagh, Ghodratollah Hashemi; Amiri, Anahita; Bagher, Zohreh; Kamrava, Seyed Kamran

2017-10-01

In this study, synthesis of a novel biocompatible stimuli-responsive conducting hydrogel based on agarose/alginate-aniline tetramer with the capability of a tailored electrically controlled drug-release for neuroregeneration is investigated. First, aniline tetramer is synthesized and grafted onto sodium alginate. Then, this material is added to agarose as an electrical conductivity modifier to obtain Agarose/alginate-aniline tetramer hydrogel. The synthesized materials are characterized by H NMR and FTIR. The hydrogels are prepared with varying content of aniline tetramer and their swelling-deswelling and shape memory behavior is evaluated. The electroactivity and ionic conductivity of hydrogels against temperature is measured. The sample with 10% aniline tetramer (AT10) reveals the highest ionic conductivity. In MTT and SEM assays, AT10 shows the best cell viability and cell proliferation due to its highest ionic conductivity highlighting the fact that electrical stimuli cell signaling. Hydrogels also represent great potentials for passive and electro-stimulated dexamethasone release. These results demonstrate that the newly developed conducting hydrogels are promising materials for neuroregenerative medicine.

Digging into the Public's Astronomy Interests

NASA Astrophysics Data System (ADS)

Miller, Scott; Simpson, R.; Gay, P.

2009-05-01

The astronomy community is good at sharing what we feel is most important or most interesting to the public via press releases, and we can get a sense of what the media wants from what they select to publish. Understanding exactly what the public most enjoys, however, was until recently mostly a matter of guesswork. Social networking sites, however, provide a place for people to publicly indicate what they like. For instance, the site http://www.digg.com allows people to submit links to interesting content on any subject and people can add "Diggs" to that linked in page. As articles gain more and more Diggs, they rise through the ranks, with the overall highest ranked sites appearing on the Digg homepage, and the highest ranked in a variety of topics, including both "Science" and the sub-topic "Space." In this poster we look at 1 month of data from Digg and study what astronomy subjects the public selects to Digg, what items have the most staying power, and compare what is Dugg to what is released via press releases during the same period.

[Soil biological activities at maize seedling stage under application of slow/controlled release nitrogen fertilizers].

PubMed

Li, Dongpo; Wu, Zhijie; Chen, Lijun; Liang, Chenghua; Zhang, Lili; Wang, Weicheng; Yang, Defu

2006-06-01

With pot experiment and simulating field ecological environment, this paper studied the effects of different slow/ controlled release N fertilizers on the soil nitrate - reductase and urease activities and microbial biomass C and N at maize seedling stage. The results showed that granular urea amended with dicyandiamide (DCD) and N-(n-bultyl) thiophosphoric triamide (NBPT) induced the highest soil nitrate-reductase activity, granular urea brought about the highest soil urease activity and microbial biomass C and N, while starch acetate (SA)-coated granular urea, SA-coated granular urea amended with DCD, methyl methacrylate (MMA) -coated granular urea amended with DCD, and no N fertilization gave a higher soil urease activity. Soil microbial C and N had a similar variation trend after applying various kinds of test slow/controlled release N fertilizers, and were the lowest after applying SA-coated granular urea amended with DCD and NBPT. Coated granular urea amended with inhibitors had a stronger effect on soil biological activities than coated granular urea, and MMA-coating had a better effect than SA-coating.

Setting accelerated dissolution test for PLGA microspheres containing peptide, investigation of critical parameters affecting drug release rate and mechanism.

PubMed

Tomic, I; Vidis-Millward, A; Mueller-Zsigmondy, M; Cardot, J-M

2016-05-30

The objective of this study was development of accelerated in vitro release method for peptide loaded PLGA microspheres using flow-through apparatus and assessment of the effect of dissolution parameters (pH, temperature, medium composition) on drug release rate and mechanism. Accelerated release conditions were set as pH 2 and 45°C, in phosphate buffer saline (PBS) 0.02M. When the pH was changed from 2 to 4, diffusion controlled phases (burst and lag) were not affected, while release rate during erosion phase decreased two-fold due to slower ester bonds hydrolyses. Decreasing temperature from 45°C to 40°C, release rate showed three-fold deceleration without significant change in release mechanism. Effect of medium composition on drug release was tested in PBS 0.01M (200 mOsm/kg) and PBS 0.01M with glucose (380 mOsm/kg). Buffer concentration significantly affected drug release rate and mechanism due to the change in osmotic pressure, while ionic strength did not have any effect on peptide release. Furthermore, dialysis sac and sample-and-separate techniques were used, in order to evaluate significance of dissolution technique choice on the release process. After fitting obtained data to different mathematical models, flow-through method was confirmed as the most appropriate for accelerated in vitro dissolution testing for a given formulation. Copyright © 2016 Elsevier B.V. All rights reserved.

FIELD-SCALE LEACHING OF ARSENIC, CHROMIUM AND COPPER FROM WEATHERED TREATED WOOD

PubMed Central

Hasan, A. Rasem; Hu, Ligang; Solo-Gabriele, Helena M.; Fieber, Lynne; Cai, Yong; Townsend, Timothy G.

2010-01-01

Earlier studies documented the loss of wood preservatives from new wood. The objective of this study was to evaluate losses from weathered treated wood under field conditions by collecting rainfall leachate from 5 different wood types, all with a surface area of 0.21 m2. Wood samples included weathered chromate copper arsenate (CCA) treated wood at low (2.7 kg/m3), medium (4.8 kg/m3) and high (35.4 kg/m3) retention levels, new alkaline copper quat (ACQ) treated wood (1.1 kg/m3 as CuO) and new untreated wood. Arsenic was found to leach at a higher rate (100 mg in 1 year for low retention) than chromium and copper (<40 mg) in all CCA treated wood samples. Copper leached at the highest rate from the ACQ sample (670 mg). Overall results suggest that metals’ leaching is a continuous process driven by rainfall, and that the mechanism of release from the wood matrix changes as wood weathers. PMID:20053493

Comparative evaluation of nickel discharge from brackets in artificial saliva at different time intervals.

PubMed

Jithesh, C; Venkataramana, V; Penumatsa, Narendravarma; Reddy, S N; Poornima, K Y; Rajasigamani, K

2015-08-01

To determine and compare the potential difference of nickel release from three different orthodontic brackets, in different artificial pH, in different time intervals. Twenty-seven samples of three different orthodontic brackets were selected and grouped as 1, 2, and 3. Each group was divided into three subgroups depending on the type of orthodontic brackets, salivary pH and the time interval. The Nickel release from each subgroup were analyzed by using inductively coupled plasma-Atomic Emission Spectrophotometer (Perkin Elmer, Optima 2100 DV, USA) model. Quantitative analysis of nickel was performed three times, and the mean value was used as result. ANOVA (F-test) was used to test the significant difference among the groups at 0.05 level of significance (P < 0.05). The descriptive method of statistics was used to calculate the mean, standard deviation, minimum and maximum. SPSS 18 software ((SPSS.Ltd, Quarry bay, Hong Kong, PASW-statistics 18) was used to analyze the study. The analysis shows a significant difference between three groups. The study shows that the nickel releases from the recycled stainless steel brackets have the highest at all 4.2 pH except in 120 h. The study result shows that the nickel release from the recycled stainless steel brackets is highest. Metal slot ceramic bracket release significantly less nickel. So, recycled stainless steel brackets should not be used for nickel allergic patients. Metal slot ceramic brackets are advisable.

Comparative evaluation of nickel discharge from brackets in artificial saliva at different time intervals

PubMed Central

Jithesh, C.; Venkataramana, V.; Penumatsa, Narendravarma; Reddy, S. N.; Poornima, K. Y.; Rajasigamani, K.

2015-01-01

Objectives: To determine and compare the potential difference of nickel release from three different orthodontic brackets, in different artificial pH, in different time intervals. Materials and Methods: Twenty-seven samples of three different orthodontic brackets were selected and grouped as 1, 2, and 3. Each group was divided into three subgroups depending on the type of orthodontic brackets, salivary pH and the time interval. The Nickel release from each subgroup were analyzed by using inductively coupled plasma-Atomic Emission Spectrophotometer (Perkin Elmer, Optima 2100 DV, USA) model. Quantitative analysis of nickel was performed three times, and the mean value was used as result. ANOVA (F-test) was used to test the significant difference among the groups at 0.05 level of significance (P < 0.05). The descriptive method of statistics was used to calculate the mean, standard deviation, minimum and maximum. SPSS 18 software ((SPSS.Ltd, Quarry bay, Hong Kong, PASW-statistics 18) was used to analyze the study. Result: The analysis shows a significant difference between three groups. The study shows that the nickel releases from the recycled stainless steel brackets have the highest at all 4.2 pH except in 120 h. Conclusion: The study result shows that the nickel release from the recycled stainless steel brackets is highest. Metal slot ceramic bracket release significantly less nickel. So, recycled stainless steel brackets should not be used for nickel allergic patients. Metal slot ceramic brackets are advisable. PMID:26538924

Drug Release Studies from Caesalpinia pulcherrima Seed Polysaccharide.

PubMed

Jeevanandham, Somasundaram; Dhachinamoorthi, Duraiswamy; Bannoth Chandra Sekhar, Kothapalli

2011-01-01

This study examines the controlled release behavior of both water-soluble (acetaminophen, caffeine, theophylline and salicylic acid) and water insoluble (indomethacin) drugs derived from Caesalpinia pulcherrima seed Gum isolated from Caesalpinia pulcherrima kernel powder. It further investigates the effect of incorporating diluents such as microcrystalline cellulose and lactose on caffeine release. In addition the effect the gum's (polysaccharide) partial cross-linking had on release of acetaminophen was examined. Applying the exponential equation, the soluble drugs mechanism of release was found to be anomalous. The insoluble drugs showed a near case II or zero order release mechanism. The rate of release in descending order was caffeine, acetaminophen, theophylline, salicylic acid and indomethacin. An increase in the release kinetics of the drug was observed on blending with diluents. However, the rate of release varied with the type and amount of blend within the matrix. The mechanism of release due to effect of diluents was found to be anomalous. The rate of drug release decreased upon partial cross-linking and the mechanism of release was found to be of super case II.

Mechanism involved in Danshen-induced fluid secretion in salivary glands

PubMed Central

Wei, Fei; Wei, Mu-Xin; Murakami, Masataka

2015-01-01

AIM: Danshen’s capability to induce salivary fluid secretion and its mechanisms were studied to determine if it could improve xerostomia. METHODS: Submandibular glands were isolated from male Wistar rats under systemic anesthesia with pentobarbital sodium. The artery was cannulated and vascularly perfused at a constant rate. The excretory duct was also cannulated and the secreted saliva was weighed in a cup on an electronic balance. The weight of the accumulated saliva was measured every 3 s and the salivary flow rate was calculated. In addition, the arterio-venous difference in the partial oxygen pressure was measured as an indicator of oxygen consumption. In order to assess the mechanism involved in Danshen-induced fluid secretion, either ouabain (an inhibitor of Na+/K+ ATPase) or bumetanide (an inhibitor of NKCC1) was additionally applied during the Danshen stimulation. In order to examine the involvement of the main membrane receptors, atropine was added to block the M3 muscarinic receptors, or phentolamine was added to block the α1 adrenergic receptors. In order to examine the requirement for extracellular Ca2+, Danshen was applied during the perfusion with nominal Ca2+ free solution. RESULTS: Although Danshen induced salivary fluid secretion, 88.7 ± 12.8 μL/g-min, n = 9, (the highest value around 20 min from start of DS perfusion was significantly high vs 32.5 ± 5.3 μL/g-min by carbamylcholine, P = 0.00093 by t-test) in the submandibular glands, the time course of that secretion differed from that induced by carbamylcholine. There was a latency associated with the fluid secretion induced by Danshen, followed by a gradual increase in the secretion to its highest value, which was in turn followed by a slow decline to a near zero level. The application of either ouabain or bumetanide inhibited the fluid secretion by 85% or 93%, and suppressed the oxygen consumption by 49% or 66%, respectively. These results indicated that Danshen activates Na+/K+ ATPase and NKCC1 to maintain Cl- release and K+ release for fluid secretion. Neither atropine or phentolamine inhibited the fluid secretion induced by Danshen (263% ± 63% vs 309% ± 45%, 227% ± 63% vs 309% ± 45%, P = 0.899, 0.626 > 0.05 respectively, by ANOVA). Accordingly, Danshen does not bind with M3 or α1 receptors. These characteristics suggested that the mechanism involved in DS-induced salivary fluid secretion could be different from that induced by carbamylcholine. Carbamylcholine activates the M3 receptor to release inositol trisphosphate (IP3) and quickly releases Ca2+ from the calcium stores. The elevation of [Ca2+]i induces chloride release and quick osmosis, resulting in an onset of fluid secretion. An increase in [Ca2+]i is essential for the activation of the luminal Cl- and basolateral K+ channels. The nominal removal of extracellular Ca2+ totally abolished the fluid secretion induced by Danshen (1.8 ± 0.8 μL/g-min vs 101.9 ± 17.2 μL/g-min, P = 0.00023 < 0.01, by t-test), suggesting the involvement of Ca2+ in the activation of these channels. Therefore, IP3-store Ca2+ release signalling may not be involved in the secretion induced by Danshen, but rather, there may be a distinct signalling process. CONCLUSION: The present findings suggest that Danshen can be used in the treatment of xerostomia, to avoid the systemic side effects associated with muscarinic drugs. PMID:25663764

Effect of injection pressure on performance, emission, and combustion characteristics of diesel-acetylene-fuelled single cylinder stationary CI engine.

PubMed

Srivastava, Anmesh Kumar; Soni, Shyam Lal; Sharma, Dilip; Jain, Narayan Lal

2018-03-01

In this paper, the effect of injection pressure on the performance, emission, and combustion characteristics of a diesel-acetylene fuelled single cylinder, four-stroke, direct injection (DI) diesel engine with a rated power of 3.5 kW at a rated speed of 1500 rpm was studied. Experiments were performed in dual-fuel mode at four different injection pressures of 180, 190, 200, and 210 bar with a flow rate of 120 LPH of acetylene and results were compared with that of baseline diesel operation. Experimental results showed that highest brake thermal efficiency of 27.57% was achieved at injection pressure of 200 bar for diesel-acetylene dual-fuel mode which was much higher than 23.32% obtained for baseline diesel. Carbon monoxide, hydrocarbon, and smoke emissions were also measured and found to be lower, while the NO x emissions were higher at 200 bar in dual fuel mode as compared to those in other injection pressures in dual fuel mode and also for baseline diesel mode. Peak cylinder pressure, net heat release rate, and rate of pressure rise were also calculated and were higher at 200 bar injection pressure in dual fuel mode.

Characteristics, location and origin of flare activity in a complex active region

NASA Technical Reports Server (NTRS)

Machado, M. E.; Gary, G. A.; Hagyard, M. J.; Hernandez, A. M.; Rovira, M. G.

1986-01-01

The observational characteristics of series of multiple-loop flares from a complex active region are summarized. The location of the highest observed photospheric magnetic shear is found to be the commonly observed site of flare onset, but not, in many cases, the magnetic region where the largest time-integrated energy release is observed. The observations thus reveal a consistent pattern of energy-release processes related to the magnetic-field topology.

Propheromones that release pheromonal carbonyl compounds in light.

PubMed

Liu, X; Macaulay, E D; Pickett, J A

1984-05-01

Pheromonal carbonyl compounds; (Z)-11-hexadecanal, (E)-citral, and 2-heptanone were treated with six alcohols to give acetals or ketals, some of which acted as propheromones by releasing the pheromonal carbonyl compounds in ultraviolet or simulated sunlight. Highest yields of pheromone were obtained from adducts prepared witho-nitrobenzyl alcohol ando-nitrophenylethane-1,2-diol. Adducts from (Z)-11-hexadecenal and these two alcohols were employed in lures to catch diamondback moths,Plutella xylostella (L.).

Final Disposition and Quality Auditing of the Rehabilitation Process in Wild Raptors Admitted to a Wildlife Rehabilitation Centre in Catalonia, Spain, during a Twelve Year Period (1995–2007)

PubMed Central

Molina-López, Rafael A.; Casal, Jordi; Darwich, Laila

2013-01-01

Background Variability in reporting and classification methods in previous published data of the final dispositions in the rehabilitation of wild raptors makes use of this data limited in trying to audit the quality of the rehabilitation process. Crude as well as stratified disposition rates are needed if quality auditing of the rehabilitation process is to be adequately performed. Methodology Final dispositions of 6221 hospitalized wild raptors admitted at a wildlife rehabilitation centre (WRC) of Catalonia during 1995–2007 were analyzed. These dispositions were calculated as the euthanasia (Er), unassisted mortality (Mr), release (Rr) and captivity rates (Cr)., time to death (Td) for dead and euthanized raptors, and length of stay for released (Tr) raptors was estimated. Stratified analyses by main causes of admission and clinical signs were performed. Results The disposition for the total population were: Er  = 30.6%, Mr = 19.1%, Rr  = 47.2%, and Cr  = 3%. By main causes of admission, Er was higher in the trauma category (34.2%), whereas Mr was found similar between trauma (37.4%) and non-trauma categories (34.8%). The highest Rr was observed for the orphaned group (77.9%). Furthermore, Cr was low in all the categories (<4%). By clinical signs, the highest Er was found in animals suffering musculoskeletal (37.9%) or skin (32.3%) lesions; Mr was high in infectious/parasitic diseases (66.7%) and in case of neurological symptoms (64.5%). The euthanized birds had a median Td  = 1 day (P10 = 0-P90 = 59) for both trauma and non-trauma categories, and Td  = 36 days for the orphaned young group (P10 = 0; P90 = 596). The median Td in the unassisted dead birds was 2 days for all the categories (P10 = 0-P90 = 31). Finally, the median Tr in the centre was variable among categories. Conclusions/Significance Reporting of final dispositions in wildlife rehabilitation should include the crude and stratified rates (Er, Mr, Rr, and Cr), by causes and clinical presentation, as well as Td and Tr, to allow meaningful auditing of the rehabilitation process quality. PMID:23613722

Residual thermal and moisture influences on the strain energy release rate analysis of local delaminations from matrix cracks

NASA Technical Reports Server (NTRS)

Obrien, T. K.

1991-01-01

An analysis utilizing laminated plate theory is developed to calculate the strain energy release rate associated with local delaminations originating at off-axis, single ply, matrix cracks in laminates subjected to uniaxial loads. The analysis includes the contribution of residual thermal and moisture stresses to the strain energy released. Examples are calculated for the strain energy release rate associated with local delaminations originating at 90 degrees and angle-ply (non-90 degrees) matrix ply cracks in glass epoxy and graphite epoxy laminates. The solution developed may be used to assess the relative contribution of mechanical, residual thermal, and moisture stresses on the strain energy release rate for local delamination for a variety of layups and materials.

Spatial Variability of Salt Marsh Vertical Accretion and Carbon Burial Rates along the Gulf of Mexico at Local and Regional Scales

NASA Astrophysics Data System (ADS)

Arriola, J.; Cable, J. E.

2017-12-01

Many studies quantifying salt marsh vertical accretion and carbon burial have been conducted along the Gulf of Mexico over the past several decades. These results are often used in conjunction with sea level rise estimates to evaluate the long term storage, and potential release, of carbon as salt marshes are overtaken by rising waters. However, results from these studies are not always comparable because of diverse sampling and analytical methods, which may skew regional averages. In addition, salt marsh vertical accretion and carbon burial rates can be highly variable on local scales depending on sampling locations within the marsh, e.g. levee vs marsh plain, and methods to determine carbon quantity, such as utilizing linear relationships between % organic matter and % carbon from other studies. Anthropogenic impacts on accretion and carbon burial may also influence interpretation of results. Utilizing consistent methods for local and regional marsh research will improve the accuracy of accretion and burial rates which is fundamental to our ability to predict responses to climate change. Our study examined sediment cores extracted from 6 salt marshes - 5 marshes along Texas to Florida coasts and 1 marsh on the Florida Atlantic coast. These marshes were selected for minimal human influence and consistent sampling and analytical methodologies were employed to compare vertical accretion and carbon burial variability on local and regional scales. Total organic carbon (TOC) and total nitrogen were determined via direct measurement and accretion rates were calculated based on 210Pb via 210Po alpha spectrometry. The lowest TOC inventory was found at Mission-Aransas, TX (18.57 g OC), whereas the highest was found at Apalachicola, FL (35.05 g OC). Anahuac, TX, was found to have the highest modern vertical accretion rates of all 6 sites, whereas Guana Tolomato-Matanzas, FL, has the lowest. This research yields regional carbon burial estimates for the Gulf of Mexico using comparable analyses to improve climate change and sea level rise predictions.

38 CFR 4.30 - Convalescent ratings.

Code of Federal Regulations, 2010 CFR

2010-07-01

... RATING DISABILITIES General Policy in Rating § 4.30 Convalescent ratings. A total disability rating (100... by report at hospital discharge (regular discharge or release to non-bed care) or outpatient release... total ratings will not be subject to § 3.105(e) of this chapter. Such total rating will be followed by...

Doctor shopping of opioid analgesics relative to benzodiazepines: A pharmacoepidemiological study among 11.7 million inhabitants in the French countries.

PubMed

Ponté, Camille; Lepelley, Marion; Boucherie, Quentin; Mallaret, Michel; Lapeyre Mestre, Maryse; Pradel, Vincent; Micallef, Joëlle

2018-06-01

The abuse of prescription opioids and its subsequent consequences is an important public concern particularly in the USA. The literature on opioid analgesic abuse is scarce. We assess the extent and risk of opioid analgesics abuse relative to benzodiazepines (BZD) using the doctor shopping method, taken into account the pharmacological characteristics (dosage, route of administration, extended or immediate release). We used SNIIRAM database covering 11.7 million inhabitants. All individuals with at least one reimbursement for non-injectable opioid analgesic or BZD in 2013 were included. Opioids for mild to moderate pain and for moderately severe to severe pain were studied. The Doctor Shopping Quantity (DSQ) is the quantity obtained by overlapping prescriptions from several prescribers. The Doctor Shopping Indicator (DSI) is the DSQ divided by the total dispensed quantity. The strong opioid analgesics have the highest DSI (2.79%) versus 2.06% for BZD hypnotics. Flunitrazepam ranked first according to its DSI (13.2%), followed by morphine (4%), and zolpidem (2.2%). The three-strong opioids having the highest DSI were morphine, oxycodone and fentanyl (respectively 4%, 1.7% and 1.5%). The highest DSI was observed for the highest dosages of morphine (DSI = 8.4% for 200 mg) and oxycodone (DSI = 2.8% for 80 mg). The highest DSI for fentanyl was described with nasal and transmucosal forms (4.1% and 3.3% respectively). The highest DSI for morphine was described for extended-release (4.1%). There is a need to reinforce surveillance systems to track opioid misuse and to increase awareness of healthcare professionals. Copyright © 2018 Elsevier B.V. All rights reserved.

Consequence assessment for Airborne Releases of SO{sub 2} from the Y-12 Pilot Dechlorination Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pendergrass, W.R.

The Atmospheric Turbulence and Diffusion Division was requested by the Department of Energy`s Oak Ridge Operations Office to conduct a consequence assessment for potential atmospheric releases of SO{sub 2} from the Y-12 Pilot Dechlorination Facility. The focus of the assessment was to identify ``worst`` case meteorology which posed the highest concentration exposure potential for both on-site as well as off-site populations. A series of plausible SO{sub 2} release scenarios were provided by Y-12 for the consequence assessment. Each scenario was evaluated for predictions of downwind concentration, estimates of a five-minute time weighted average, and estimate of the dimension of themore » puff. The highest hazard potential was associated with Scenario 1, in which a total of eight SO{sub 2} cylinders are released internally to the Pilot Facility and exhausted through the emergency venting system. A companion effort was also conducted to evaluate the potential for impact of releases of SO{sub 2} from the Pilot Facility on the population of Oak Ridge. While specific transport trajectory data is not available for the Pilot Facility, extrapolations based on the Oak Ridge Site Survey and climatological records from the Y-12 meteorological program does not indicate the potential for impact on the city of Oak Ridge. Steering by the local topographical features severely limits the potential impact ares. Due to the lack of specific observational data, both tracer and meteorological, only inferences can be made concerning impact zones. It is recommended tat the Department of Energy Oak Ridge Operations examine the potential for off-site impact and develop the background data to prepare impact zones for releases of hazardous materials from the Y-12 facility.« less

Drug release through liposome pores.

PubMed

Dan, Nily

2015-02-01

Electrical, ultrasound and other types of external fields are known to induce the formation of pores in cellular and model membranes. This paper examines drug release through field induced liposome pores using Monte Carlo simulations. We find that drug release rates vary as a function of pore size and spacing, as well as the overall fraction of surface area covered by pores: The rate of release from liposomes is found to increase rapidly with pore surface coverage, approaching that of the fully ruptured liposome at fractional pore areas. For a given pore surface coverage, the pore size affects the release rate in the limit of low coverage, but not when the pores cover a relatively high fraction of the liposome surface area. On the other hand, for a given pore size and surface coverage, the distribution of pores significantly affects the release in the limit of high surface coverage: The rate of release from a liposome covered with a regularly spaced array of pores is, in this limit, higher than the release rate from (most) systems where the pores are distributed randomly on the liposome surface. In contrast, there is little effect of the pore distribution on release when the pore surface coverage is low. The simulation results are in good agreement with the predictions of detailed diffusion models. Copyright © 2014 Elsevier B.V. All rights reserved.

Quantification of Kinetic Rate Law Parameters of Uranium Release from Sodium Autunite as a Function of Aqueous Bicarbonate Concentrations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gudavalli, Ravi; Katsenovich, Yelena; Wellman, Dawn M.

2013-09-05

ABSTRACT: Hydrogen carbonate is one of the most significant components within the uranium geochemical cycle. In aqueous solutions, hydrogen carbonate forms strong complexes with uranium. As such, aqueous bicarbonate may significantly increase the rate of uranium release from uranium minerals. Quantifying the relationship of aqueous hydrogen carbonate solutions to the rate of uranium release during dissolution is critical to understanding the long-term fate of uranium within the environment. Single-pass flow-through (SPTF) experiments were conducted to estimate the rate of uranium release from Na meta-autunite as a function of bicarbonate solutions (0.0005-0.003 M) under the pH range of 6-11 and temperaturesmore » of 5-60oC. Consistent with the results of previous investigation, the rate of uranium release from sodium autunite exhibited minimal dependency on temperature; but were strongly dependent on pH and increasing concentrations of bicarbonate solutions. Most notably at pH 7, the rate of uranium release exhibited 370 fold increases relative to the rate of uranium release in the absence of bicarbonate. However, the effect of increasing concentrations of bicarbonate solutions on the release of uranium was significantly less under higher pH conditions. It is postulated that at high pH values, surface sites are saturated with carbonate, thus the addition of more bicarbonate would have less effect on uranium release. Results indicate the activation energies were unaffected by temperature and bicarbonate concentration variations, but were strongly dependent on pH conditions. As pH increased from 6 to 11, activation energy values were observed to decrease from 29.94 kJ mol-1 to 13.07 kJ mol-1. The calculated activation energies suggest a surface controlled dissolution mechanism.« less

Controlled release of insect sex pheromones from paraffin wax and emulsions.

PubMed

Atterholt, C A; Delwiche, M J; Rice, R E; Krochta, J M

1999-02-22

Paraffin wax and aqueous paraffin emulsions can be used as controlled release carriers for insect sex pheromones for mating disruption of orchard pests. Paraffin can be applied at ambient temperature as an aqueous emulsion, adheres to tree bark or foliage, releases pheromone for an extended period of time, and will slowly erode from bark and biodegrade in soil. Pheromone emulsions can be applied with simple spray equipment. Pheromone release-rates from paraffin were measured in laboratory flow-cell experiments. Pheromone was trapped from an air stream with an adsorbent, eluted periodically, and quantified by gas chromatography. Pheromone release from paraffin was partition-controlled, providing a constant (zero-order) release rate. A typical paraffin emulsion consisted of 30% paraffin, 4% pheromone, 4% soy oil, 1% vitamin E, 2% emulsifier, and the balance water. Soy oil and vitamin E acted as volatility suppressants. A constant release of oriental fruit moth pheromone from paraffin emulsions was observed in the laboratory for more than 100 days at 27 degreesC, with release-rates ranging from 0.4 to 2 mg/day, depending on the concentration and surface area of the dried emulsion. The use of paraffin emulsions is a viable method for direct application of insect pheromones for mating disruption. Sprayable formulations can be designed to release insect pheromones to the environment at a rate necessary for insect control by mating disruption. At temperatures below 38 degreesC, zero-order release was observed. At 38 degreesC and higher, pheromone oxidation occurred. A partition-controlled release mechanism was supported by a zero-order pheromone release-rate, low air/wax partition coefficients, and pheromone solubility in paraffin.

Liquid-Phase Heat-Release Rates of the Systems Hydrazine-Nitric Acid and Unsymmetrical Dimethylhydrazine-Nitric Acid

NASA Technical Reports Server (NTRS)

Somogyi, Dezso; Feiler, Charles E.

1960-01-01

The initial rates of heat release produced by the reactions of hydrazine and unsymmetrical dimethylhydrazine with nitric acid were determined in a bomb calorimeter under conditions of forced mixing. Fuel-oxidant weight ratio and injection velocity were varied. The rate of heat release apparently depended on the interfacial area between the propellants. Above a narrow range of injection velocities representing a critical amount of interfacial area, the rates reached a maximum and were almost constant with injection velocity. The maximum rate for hydrazine was about 70 percent greater than that for unsymmetrical dimethylhydrazine. The total heat released did not vary with mixture ratio over the range studied.

Transit losses and traveltimes for water-supply releases Marion Lake during drought conditions, Cottonwood River, east-central Kansas

USGS Publications Warehouse

Jordan, P.R.; Hart, R.J.

1985-01-01

A streamflow routing model was used to calculate the transit losses and traveltimes. Channel and aquifer characteristics, and the model control parameters, were estimated from available data and then verified to the extent possible by comparing model simulated streamflow to observed streamflow at streamflow gaging stations. Transit losses and traveltimes for varying reservoir release rates and durations then were simulated for two different antecedent streamflow (drought) conditions. For the severe-drought antecedent-streamflow condition, it was assumed that only the downstream water use requirement would be released from the reservoir. For a less severe drought (LSD) antecedent streamflow condition, it was assumed than any releases from Marion Lake for water supply use downstream, would be in addition to a nominal dry weather release of 5 cu ft/sec. Water supply release rates of 10 and 25 cu ft/sec for the severe drought condition and 5, 10, and 25 cu ft/sec for the less severe drought condition were simulated for periods of 28 and 183 days commencing on July 1. Transit losses for the severe drought condition for all reservoir release rates and durations ranged from 12% to 78% of the maximum downstream flow rate and from 27% to 91% of the total volume of reservoir storage released. For the LSD condition, transit losses ranged from 7% to 29% of the maximum downstream flow rate and from 10% to 48% of the total volume of release. The 183-day releases had larger total transit losses, but losses on a percentage basis were less than the losses for the 28-day release period for both antecedent streamflow conditions. Traveltimes to full response (80% of the maximum downstream flow rate), however, showed considerable variation. For the release of 5 cu ft/sec during LSD conditions, base flow exceeded 80% of the maximum flow rate near the confluence; the traveltime to full response was undefined for those simulations. For the releases of 10 and 25 cu ft/sec during the same drought condition, traveltimes to full response ranged from 4.4 to 6.5 days. For releases of 10 and 25 cu ft/sec during severe drought conditions, traveltimes to full response near the confluence with the Neosho River ranged from 8.3 to 93 days. (Lantz-PTT)

Effects of pH, Temperature, Dissolved Oxygen, and Flow Rate on Phosphorus Release Processes at the Sediment and Water Interface in Storm Sewer

PubMed Central

Li, Haiyan; Li, Mingyi; Zhang, Xiaoran

2013-01-01

The effects of pH, temperature, dissolved oxygen (DO), and flow rate on the phosphorus (P) release processes at the sediment and water interface in rainwater pipes were investigated. The sampling was conducted in a residential storm sewer of North Li Shi Road in Xi Cheng District of Beijing on August 3, 2011. The release rate of P increased with the increase of pH from 8 to 10. High temperature is favorable for the release of P. The concentration of total phosphorus (TP) in the overlying water increased as the concentration of DO decreased. With the increase of flow rate from 0.7 m s−1 to 1.1 m s−1, the concentration of TP in the overlying water increased and then tends to be stable. Among all the factors examined in the present study, the flow rate is the primary influence factor on P release. The cumulative amount of P release increased with the process of pipeline runoff in the rainfall events with high intensities and shorter durations. Feasible measures such as best management practices and low-impact development can be conducted to control the P release on urban sediments by slowing down the flow rate. PMID:24349823

Rate of Heat Release in Diesel Engines

DOT National Transportation Integrated Search

1977-10-01

In this report, the concept of heat release in diesel engines is compared with reaction rates in petrol engines as a means of describing combustion. The intimate relationships between heat release, cylinder pressure development and cylinder pressure ...

Optimization and development of a core-in-cup tablet for modulated release of theophylline in simulated gastrointestinal fluids.

PubMed

Danckwerts, M P

2000-07-01

A triple-layer core-in-cup tablet that can release theophylline in simulated gastrointestinal (GI) fluids at three distinct rates has been developed. The first layer is an immediate-release layer; the second layer is a sustained-release layer; and the last layer is a boost layer, which was designed to coincide with a higher nocturnal dose of theophylline. The study consisted of two stages. The first stage optimized the sustained-release layer of the tablet to release theophylline over a period of 12 hr. Results from this stage indicated that 30% w/w acacia gum was the best polymer and concentration to use when compressed to a hardness of 50 N/m2. The second stage of the study involved the investigation of the final triple-layer core-in-cup tablet to release theophylline at three different rates in simulated GI fluids. The triple-layer modulated core-in-cup tablet successfully released drug in simulated fluids at an initial rate of 40 mg/min, followed by a rate of 0.4085 mg/min, in simulated gastric fluid TS, 0.1860 mg/min in simulated intestinal fluid TS, and finally by a boosted rate of 0.6952 mg/min.

Effect of detention basin release rates on flood flows - Application of a model to the Blackberry Creek Watershed in Kane County, Illinois

USGS Publications Warehouse

Soong, David T.; Murphy, Elizabeth A.; Straub, Timothy D.

2009-01-01

The effects of stormwater detention basins with specified release rates are examined on the watershed scale with a Hydrological Simulation Program - FORTRAN (HSPF) continuous-simulation model. Modeling procedures for specifying release rates from detention basins with orifice and weir discharge configurations are discussed in this report. To facilitate future detention modeling as a tool for watershed management, a chart relating watershed impervious area to detention volume is presented. The report also presents a case study of the Blackberry Creek watershed in Kane County, Ill., a rapidly urbanizing area seeking to avoid future flood damages from increased urbanization, to illustrate the effects of various detention basin release rates on flood peaks and volumes and flood frequencies. The case study compares flows simulated with a 1996 land-use HSPF model to those simulated with four different 2020 projected land-use HSPF model scenarios - no detention, and detention basins with release rates of 0.08, 0.10, and 0.12 cubic feet per second per acre (ft3/s-acre), respectively. Results of the simulations for 15 locations, which included the downstream ends of all tributaries and various locations along the main stem, showed that a release rate of 0.10 ft3/s-acre, in general, can maintain postdevelopment 100-year peak-flood discharge at a similar magnitude to that of 1996 land-use conditions. Although the release rate is designed to reduce the 100-year peak flow, reduction of the 2-year peak flow is also achieved for a smaller proportion of the peak. Results also showed that the 0.10 ft3/s-acre release rate was less effective in watersheds with relatively high percentages of preexisting (1996) development than in watersheds with less preexisting development.

Phosphorus fraction and phosphate sorption-release characteristics of the wetland sediments in the Yellow River Delta

NASA Astrophysics Data System (ADS)

Cui, Yuan; Xiao, Rong; Xie, Ying; Zhang, Mingxiang

2018-02-01

The aim of this study was to investigate phosphorus (P) fractions and phosphate sorption-release characteristics of the surface sediments regarding the wetland restoration in the Yellow River Delta (YRD). Sediments samples were collected from three typical sample plots: Phragmites australis community (p), Suaeda salsa community (s), and bare land (b) both in natural wetland (N) and restored wetland (R). The results showed that the mean content of TP was 541.58 mg/kg, and the rank order of P fractions were: inorganic phosphorus (IP) (65.6%) > residual phosphorus (RP) (24.9%) > organic phosphorus (OP) (9.5%). For sediments under the same land cover, TP and OP contents were significantly higher in natural wetlands than those in restored wetlands. This indicated that the restoration project really made a difference in TP content of sediments, and the decreased TP might result from decreased OP. For P kinetics sorption, a quick sorption mainly occurred within 0.5 h. The maximum phosphorus adsorption capacities (Qmax) ranging from 139.40 mg/kg to 224.06 mg/kg and the bonding energy constant (K) ranging from 0.33 mg/L to 1.37 mg/L were both obtained using a Langmuir model. In addition, Qmax, P release (Pr) and P release rates (Prr) were in the order of Nb > Np > Ns > Rb > Rp > Rs, Np > Rp > Ns > Rs = Nb > Rb and Rp > Ns > Rs > Rb > Np > Nb, respectively. This indicated that sediments from natural wetland could adsorb more P as well as release more P into overlying water, moreover, more content of P were left in sediments comparing to restored wetland. Sediments from bare land were more likely to retain P as a pool because of the highest sorption capacity while lowest release potential. Our study showed that P sorption-release and the quick sorption processes were mainly affected by sediment moisture, amorphous iron and aluminum oxides (Feox and Alox). Besides, Qmax was related to background value of sediments P. OP was the major P fraction adsorbed by sediments, and the P adsorbed by sediments was mainly adsorbed on Feox and Alox.

[Effect on iron release in drinking water distribution systems].

PubMed

Niu, Zhang-bin; Wang, Yang; Zhang, Xiao-jian; Chen, Chao; Wang, Sheng-hui

2007-10-01

Batch-scale experiments were done to quantitatively study the effect of inorganic chemical parameters on iron release in drinking water distribution systems. The parameters include acid-base condition, oxidation-reduction condition, and neutral ion condition. It was found that the iron release rate decreased with pH, alkalinity, the concentration of dissolved oxygen increasing, and the iron release rate increased with the concentration of chloride increasing. The theoretical critical formula of iron release rate was elucidated. According to the formula, the necessary condition for controlling iron release is that pH is above 7.6, the concentration of alkalinity and dissolved oxygen is more than 150 mg/L and 2 mg/L, and the concentration of chloride is less than 150 mg/L of distributed water.

Development and evaluation of N-naphthyl-N,O-succinyl chitosan micelles containing clotrimazole for oral candidiasis treatment.

PubMed

Tonglairoum, Prasopchai; Woraphatphadung, Thisirak; Ngawhirunpat, Tanasait; Rojanarata, Theerasak; Akkaramongkolporn, Prasert; Sajomsang, Warayuth; Opanasopit, Praneet

2017-03-01

Clotrimazole (CZ)-loaded N-naphthyl-N,O-succinyl chitosan (NSCS) micelles have been developed as an alternative for oral candidiasis treatment. NSCS was synthesized by reductive N-amination and N,O-succinylation. CZ was incorporated into the micelles using various methods, including the dropping method, the dialysis method, and the O/W emulsion method. The size and morphology of the CZ-loaded micelles were characterized using dynamic light scattering measurements (DLS) and a transmission electron microscope (TEM), respectively. The drug entrapment efficiency, loading capacity, release characteristics, and antifungal activity against Candida albicans were also evaluated. The CZ-loaded micelles prepared using different methods differed in the size of micelles. The micelles ranged in size from 120 nm to 173 nm. The micelles prepared via the O/W emulsion method offered the highest percentage entrapment efficiency and loading capacity. The CZ released from the CZ-loaded micelles at much faster rate compared to CZ powder. The CZ-loaded NSCS micelles can significantly hinder the growth of Candida cells after contact. These CZ-loaded NSCS micelles offer great antifungal activity and might be further developed to be a promising candidate for oral candidiasis treatment.

Effect of decreasing temperature on the strobilation of Aurelia sp.1

NASA Astrophysics Data System (ADS)

Shi, Yan; Yu, Zhigang; Zhen, Yu; Wang, Guoshan; Wang, Xungong; Mi, Tiezhu

2018-03-01

The worldwide proliferation of marine jellyfish has become a crucial ecological and social issue, and as a cosmopolitan species, Aurelia spp. have received increasing scientific attentions. In the present study, the responses of strobilation in Aurelia sp.1 to decreasing temperature were illuminated through the expression levels of the retinoid x receptor (RxR) gene and the gene encoding a secreted protein, CL390. We observed that a higher final temperature decreased the strobilation prophase and strobilation interphase periods, and the growth rate of the strobilae ratio increased with increasing CL390 gene expression. The ratio of strobilae at 12°C was highest, and the strobilae showed the higher releasing ratios at both 12°C and 16°C compared with those at 4°C and 8°C. Furthermore, more ephyrae were released at the higher final temperature. Additionally, up-regulation and down-regulation of the CL390 gene were observed in response to the four decreasing temperatures. Although the four CL390 gene transcript levels increased more significantly than the transcript levels of the RxR gene, similar trends were observed in both genes.

Tidal pulsing alters nitrous oxide fluxes in a temperate intertidal mudflat.

PubMed

Vieillard, A M; Fulweiler, R W

2014-07-01

Environmental pulses, or sudden, marked changes to the conditions within an ecosystem, can be important drivers of resource availability in many systems. In this study, we investigated the effect of tidal pulsing on the fluxes of nitrous oxide (N2O), a powerful greenhouse gas, from a marine intertidal mudflat on the north shore of Massachusetts, USA. We found these tidal flat sediments to be a sink of N2O at low tide with an average uptake rate of -6.7 +/- 2 micromol x m(-2) x h(-1). Further, this N20 sink increased the longer sediments were tidally exposed. These field measurements, in conjunction with laboratory nutrient additions, revealed that this flux appears to be driven primarily by sediment denitrification. Additionally, N2O uptake was most responsive to dissolved inorganic nitrogen with phosphorus (DIN + DIP) addition, suggesting that the N2O consumption process may be P limited. Furthermore, nutrient addition experiments suggest that dissimilatory nitrate reduction to ammonium (DNRA) releases N20 at the highest levels of nitrate fertilization. Our findings indicate that tidal flats are important sinks of N2O, potentially capable of offsetting the release of this potent greenhouse gas by other, nearby ecosystems.

Polyethylenimine-modified curcumin-loaded mesoporus silica nanoparticle (MCM-41) induces cell death in MCF-7 cell line.

PubMed

Harini, Lakshminarasimhan; Karthikeyan, Bose; Srivastava, Sweta; Suresh, Srinag Bangalore; Ross, Cecil; Gnanakumar, Georgepeter; Rajagopal, Srinivasan; Sundar, Krishnan; Kathiresan, Thandavarayan

2017-02-01

Breast cancer accounts for the first highest mortality rate in India and second in world. Though current treatment strategies are effectively killing cancer cells, they also end in causing severe side effects and drug resistance. Curcumin is a nutraceutical with multipotent activity but its insolubility in water limits its therapeutic potential as an anti-cancer drug. The hydrophilicity of curcumin could be increased by nanoformulation or changing its functional groups. In this study, curcumin is loaded on mesoporous silica nanoparticle and its anti-cancer activity is elucidated with MCF-7 cell death. Structural characteristics of Mobil Composition of Matter - 41(MCM-41) as determined by high-resolution transmission electron microscopy (HR-TEM) shows that MCM-41 size ranges from 100 to 200 nm diameters with pore size 2-10 nm for drug adsorption. The authors found 80-90% of curcumin is loaded on MCM-41 and curcumin is released efficiently at pH 3.0. The 50 µM curcumin-loaded MCM-41 induced 50% mortality of MCF-7 cells. Altogether, their results suggested that increased curcumin loading and sustained release from MCM-41 effectively decreased cell survival of MCF-7 cells in vitro.

Antimicrobial paper based on a soy protein isolate or modified starch coating including carvacrol and cinnamaldehyde.

PubMed

Arfa, Afef Ben; Preziosi-Belloy, Laurence; Chalier, Pascale; Gontard, Nathalie

2007-03-21

Soy protein isolates (SPI) and octenyl-succinate (OSA) modified starch were used as paper coating and inclusion matrices of two antimicrobial compounds: cinnamaldehyde and carvacrol. Antimicrobial compound losses from the coated papers were evaluated after the coating and drying process, and the two matrices demonstrated retention ability that depended on the compound nature and concentration. Whereas carvacrol losses ranged between 12 and 45%, cinnamaldehyde losses varied from 43 to 76%. The losses were always higher from OSA-starch-coated papers than from SPI-coated papers. During storage in accelerated conditions, at 30 degrees C and 60% relative humidity, carvacrol retention from coated papers was found to be similar whatever the coating matrices and the carvacrol rate. In contrast, the retention from SPI-coated papers was particularly high for the cinnamaldehyde concentration of 30% (w/w) compared to the lowest (10% w/w) or highest concentration (60% w/w). Compared to carvacrol, faster release was observed, particurlarly when OSA-starch was used. The antimicrobial properties of the coated papers were shown against Escherichia coli and Botrytis cinerea and explained by favorable conditions of total release of the antimicrobial agents.

Increased skin permeation efficiency of imperatorin via charged ultradeformable lipid vesicles for transdermal delivery

PubMed Central

Lin, Hongwei; Xie, Qingchun; Huang, Xin; Ban, Junfeng; Wang, Bo; Wei, Xing

2018-01-01

Aim The aim of this work was to develop a novel vesicular carrier, ultradeformable liposomes (UDLs), to expand the applications of the Chinese herbal medicine, imperatorin (IMP), and increase its transdermal delivery. Methods In this study, we prepared IMP-loaded UDLs using the thin-film hydration method and evaluated their encapsulation efficiency, vesicle deformability, skin permeation, and the amounts accumulated in different depths of the skin in vitro. The influence of different charged surfactants on the properties of the UDLs was also investigated. Results The results showed that the UDLs containing cationic surfactants had high entrapment efficiency (60.32%±2.82%), an acceptable particle size (82.4±0.65 nm), high elasticity, and prolonged drug release. The penetration rate of IMP in cationic-UDLs was 3.45-fold greater than that of IMP suspension, which was the highest value among the vesicular carriers. UDLs modified with cationic surfactant also showed higher fluorescence intensity in deeper regions of the epidermis. Conclusion The results of our study suggest that cationic surfactant-modified UDLs could increase the transdermal flux, prolong the release of the drug, and serve as an effective dermal delivery system for IMP. PMID:29467573

Increased skin permeation efficiency of imperatorin via charged ultradeformable lipid vesicles for transdermal delivery.

PubMed

Lin, Hongwei; Xie, Qingchun; Huang, Xin; Ban, Junfeng; Wang, Bo; Wei, Xing; Chen, Yanzhong; Lu, Zhufen

2018-01-01

The aim of this work was to develop a novel vesicular carrier, ultradeformable liposomes (UDLs), to expand the applications of the Chinese herbal medicine, imperatorin (IMP), and increase its transdermal delivery. In this study, we prepared IMP-loaded UDLs using the thin-film hydration method and evaluated their encapsulation efficiency, vesicle deformability, skin permeation, and the amounts accumulated in different depths of the skin in vitro. The influence of different charged surfactants on the properties of the UDLs was also investigated. The results showed that the UDLs containing cationic surfactants had high entrapment efficiency (60.32%±2.82%), an acceptable particle size (82.4±0.65 nm), high elasticity, and prolonged drug release. The penetration rate of IMP in cationic-UDLs was 3.45-fold greater than that of IMP suspension, which was the highest value among the vesicular carriers. UDLs modified with cationic surfactant also showed higher fluorescence intensity in deeper regions of the epidermis. The results of our study suggest that cationic surfactant-modified UDLs could increase the transdermal flux, prolong the release of the drug, and serve as an effective dermal delivery system for IMP.

Wax-based sustained release matrix pellets prepared by a novel freeze pelletization technique II. In vitro drug release studies and release mechanisms.

PubMed

Cheboyina, Sreekhar; Wyandt, Christy M

2008-07-09

A novel freeze pelletization technique was evaluated for the preparation of wax-based sustained release matrix pellets. Pellets containing water-soluble drugs were successfully prepared using a variety of waxes. The drug release significantly depended on the wax type used and the aqueous drug solubility. The drug release decreased as the hydrophobicity of wax increased and the drug release increased as the aqueous drug solubility increased. In glyceryl monostearate (GMS) pellets, drug release rate decreased as the loading of theophylline increased. On the contrary, the release rate increased as the drug loading of diltiazem HCl increased in Precirol pellets. Theophylline at low drug loads existed in a dissolved state in GMS pellets and the release followed desorption kinetics. At higher loads, theophylline existed in a crystalline state and the release followed dissolution-controlled constant release for all the waxes studied. However, with the addition of increasing amounts of Brij 76, theophylline release rate increased and the release mechanism shifted to diffusion-controlled square root time kinetics. But the release of diltiazem HCl from Precirol pellets at all drug loads, followed diffusion-controlled square root time kinetics. Therefore, pellets capable of providing a variety of release profiles for different drugs can be prepared using this freeze pelletization technique by suitably modifying the pellet forming matrix compositions.

Release kinetics of vanadium from vanadium (III, IV and V) oxides: Effect of pH, temperature and oxide dose.

PubMed

Hu, Xingyun; Yue, Yuyan; Peng, Xianjia

2018-05-01

Batch experiments were performed to derive the rate laws for the proton-promoted dissolution of the main vanadium (III, IV and V) oxides at pH 3.1-10.0. The release rates of vanadium are closely related to the aqueous pH, and several obvious differences were observed in the release behavior of vanadium from the dissolution of V 2 O 5 and vanadium(III, IV) oxides. In the first 2hr, the release rates of vanadium from V 2 O 3 were r=1.14·([H + ]) 0.269 at pH 3.0-6.0 and r=0.016·([H + ]) -0.048 at pH 6.0-10.0; the release rates from VO 2 were r=0.362·([H + ]) 0.129 at pH 3.0-6.0 and r=0.017·([H + ]) -0.097 at pH 6.0-10.0; and the release rates from V 2 O 5 were r=0.131·([H + ]) -0.104 at pH 3.1-10.0. The release rates of vanadium from the three oxides increased with increasing temperature, and the effect of temperature was different at pH 3.8, pH 6.0 and pH 7.7. The activation energies of vanadium (III, IV and V) oxides (33.4-87.5kJ/mol) were determined at pH 3.8, pH6.0 and pH 7.7, showing that the release of vanadium from dissolution of vanadium oxides follows a surface-controlled reaction mechanism. The release rates of vanadium increased with increasing vanadium oxides dose, albeit not proportionally. This study, as part of a broader study of the release behavior of vanadium, can help to elucidate the pollution problem of vanadium and to clarify the fate of vanadium in the environment. Copyright © 2017. Published by Elsevier B.V.

Fetal Heart Rate Monitoring during Intrauterine Open Surgery for Myelomeningocele Repair.

PubMed

Santana, Eduardo Félix Martins; Moron, Antônio Fernandes; Barbosa, Maurício Mendes; Milani, Herbene Jose Figuinha; Sarmento, Stephanno Gomes Pereira; Araujo Júnior, Edward; Rolo, Liliam Cristine; Cavalheiro, Sérgio

2016-01-01

The aim of this study was to assess fetal hemodynamics during intrauterine open surgery for myelomeningocele (MMC) repair by describing fetal heart rate (FHR) monitoring in detail related to each part of the procedure. A study was performed with 57 fetuses submitted to intrauterine MMC repair between the 24th and 27th week of gestation. Evaluations of FHR were made in specific periods: before anesthesia, after anesthesia, at the beginning of laparotomy, during uterus abdominal withdrawal, hysterotomy, neurosurgery (before incision, during early skin manipulation, spinal cord releasing, and at the end of neurosurgery), abdominal cavity reintroduction, and abdominal closure, and at the end of surgery. Means ± standard deviations of FHR were established for each period, and analysis of variance with repeated measures was used to assess differences between these periods. The mean differences were assessed with 95% confidence intervals and were analyzed by Tukey's multiple comparison test. The mean FHR during the specific periods mentioned above was 140.2, 140, 139.2, 138.8, 135.1, 133.9, 123.1, 134.0, 134.5, 137.9, and 139.9 bpm, respectively (p < 0.0001). Comparing the different periods, the highest frequencies were observed in the initial and final moments. The neurosurgery stage presents lower frequencies, especially during the release of the spinal cord. FHR monitoring revealed interesting findings in terms of physiological fetal changes during MMC repair, especially during neurosurgery, which was the most critical period. © 2015 S. Karger AG, Basel.

Personal Breathing Zone Exposures among Hot-Mix Asphalt Paving Workers; Preliminary Analysis for Trends and Analysis of Work Practices That Resulted in the Highest Exposure Concentrations

PubMed Central

Osborn, Linda V.; Snawder, John E.; Kriech, Anthony J.; Cavallari, Jennifer M.; McClean, Michael D.; Herrick, Robert F.; Blackburn, Gary R.; Olsen, Larry D.

2015-01-01

An exposure assessment of hot-mix asphalt (HMA) paving workers was conducted to determine which of four exposure scenarios impacted worker exposure and dose. Goals of this report are to present the personal-breathing zone (PBZ) data, discuss the impact of substituting the releasing/cleaning agent, and discuss work practices that resulted in the highest exposure concentration for each analyte. One-hundred-seven PBZ samples were collected from HMA paving workers on days when diesel oil was used as a releasing/cleaning agent. An additional 36 PBZ samples were collected on days when B-100 (100% biodiesel, containing no petroleum-derived products) was used as a substitute releasing/cleaning agent. Twenty-four PBZ samples were collected from a reference group of concrete workers, who also worked in outdoor construction but had no exposure to asphalt emissions. Background and field blank samples were also collected daily. Total particulates and the benzene soluble fraction were determined gravimetrically. Total organic matter was determined using gas chromatography (GC) with flame ionization detection and provided qualitative information about other exposure sources contributing to worker exposure besides asphalt emissions. Thirty-three individual polycyclic aromatic compounds (PACs) were determined using GC with time-offlight mass spectrometry; results were presented as either the concentration of an individual PAC or a summation of the individual PACs containing either 2- to 3-rings or 4- to 6-rings. Samples were also screened for PACs containing 4- to 6-rings using fluorescence spectroscopy. Arithmetic means, medians, and box plots of the PBZ data were used to evaluate trends in the data. Box plots illustrating the diesel oil results were more variable than the B-100. Also, the highest diesel oil results were much higher in concentration than the highest B-100 results. An analysis of the highest exposure results and field notes revealed a probable association between these exposures and the use of diesel oil, use of a diesel-powered screed, elevated HMA paving application temperatures, lubricating and working on broken-down equipment, and operation of a broom machine. PMID:24195533

Personal breathing zone exposures among hot-mix asphalt paving workers; preliminary analysis for trends and analysis of work practices that resulted in the highest exposure concentrations.

PubMed

Osborn, Linda V; Snawder, John E; Kriech, Anthony J; Cavallari, Jennifer M; McClean, Michael D; Herrick, Robert F; Blackburn, Gary R; Olsen, Larry D

2013-01-01

An exposure assessment of hot-mix asphalt (HMA) paving workers was conducted to determine which of four exposure scenarios impacted worker exposure and dose. Goals of this report are to present the personal-breathing zone (PBZ) data, discuss the impact of substituting the releasing/cleaning agent, and discuss work practices that resulted in the highest exposure concentration for each analyte. One-hundred-seven PBZ samples were collected from HMA paving workers on days when diesel oil was used as a releasing/cleaning agent. An additional 36 PBZ samples were collected on days when B-100 (100% biodiesel, containing no petroleum-derived products) was used as a substitute releasing/cleaning agent. Twenty-four PBZ samples were collected from a reference group of concrete workers, who also worked in outdoor construction but had no exposure to asphalt emissions. Background and field blank samples were also collected daily. Total particulates and the benzene soluble fraction were determined gravimetrically. Total organic matter was determined using gas chromatography (GC) with flame ionization detection and provided qualitative information about other exposure sources contributing to worker exposure besides asphalt emissions. Thirty-three individual polycyclic aromatic compounds (PACs) were determined using GC with time-of-flight mass spectrometry; results were presented as either the concentration of an individual PAC or a summation of the individual PACs containing either 2- to 3-rings or 4- to 6-rings. Samples were also screened for PACs containing 4- to 6-rings using fluorescence spectroscopy. Arithmetic means, medians, and box plots of the PBZ data were used to evaluate trends in the data. Box plots illustrating the diesel oil results were more variable than the B-100. Also, the highest diesel oil results were much higher in concentration than the highest B-100 results. An analysis of the highest exposure results and field notes revealed a probable association between these exposures and the use of diesel oil, use of a diesel-powered screed, elevated HMA paving application temperatures, lubricating and working on broken-down equipment, and operation of a broom machine.

A primary estimate of global PCDD/F release based on the quantity and quality of national economic and social activities.

PubMed

Wang, Bin; Fiedler, Heidelore; Huang, Jun; Deng, Shubo; Wang, Yujue; Yu, Gang

2016-05-01

The correlations between polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) releases and factors relevant to human social-economic activities (HSEAs) were analyzed. The multiple linear regression model was successfully developed to estimate the total global PCDD/F release. The PCDD/F releases significantly correlated with population, area, GDP and GNI, suggesting that "quantity" of HSEAs have significantly contributed to the PCDD/F releases. On another aspect, advanced technologies are usually adopted in developed countries/regions, and hence reduce the PCDD/F release. The significant correlation between PCDD/F release and CO2 emission implies the potential of simultaneous reduction of CO2 emission and PCDD/F release. The total global PCDD/F release from 196 countries/regions was estimated to be 100.4 kg-TEQ yr(-1). The estimated annual PCDD/F release per unit area ranged from 0.007 to 28 mg-TEQ km(-2). Asia is estimated to have the highest PCDD/F release of 47.1 kg-TEQ yr(-1), almost half of the total world release. Oceania is estimated to have the smallest total release but the largest per-capita release. For the developed areas, such as Europe and North America, the PCDD/F release per unit GDP is lower, while for Africa, it is much higher. Copyright © 2016 Elsevier Ltd. All rights reserved.

Differential effects of buffer pH on Ca2+-induced ROS emission with inhibited mitochondrial complexes I and III

PubMed Central

Lindsay, Daniel P.; Camara, Amadou K. S.; Stowe, David F.; Lubbe, Ryan; Aldakkak, Mohammed

2015-01-01

Excessive mitochondrial reactive oxygen species (ROS) emission is a critical component in the etiology of ischemic injury. Complex I and complex III of the electron transport chain are considered the primary sources of ROS emission during cardiac ischemia and reperfusion (IR) injury. Several factors modulate ischemic ROS emission, such as an increase in extra-matrix Ca2+, a decrease in extra-matrix pH, and a change in substrate utilization. Here we examined the combined effects of these factors on ROS emission from respiratory complexes I and III under conditions of simulated IR injury. Guinea pig heart mitochondria were suspended in experimental buffer at a given pH and incubated with or without CaCl2. Mitochondria were then treated with either pyruvate, a complex I substrate, followed by rotenone, a complex I inhibitor, or succinate, a complex II substrate, followed by antimycin A, a complex III inhibitor. H2O2 release rate and matrix volume were compared with and without adding CaCl2 and at pH 7.15, 6.9, or 6.5 with pyruvate + rotenone or succinate + antimycin A to simulate conditions that may occur during in vivo cardiac IR injury. We found a large increase in H2O2 release with high [CaCl2] and pyruvate + rotenone at pH 6.9, but not at pHs 7.15 or 6.5. Large increases in H2O2 release rate also occurred at each pH with high [CaCl2] and succinate + antimycin A, with the highest levels observed at pH 7.15. The increases in H2O2 release were associated with significant mitochondrial swelling, and both H2O2 release and swelling were abolished by cyclosporine A, a desensitizer of the mitochondrial permeability transition pore (mPTP). These results indicate that ROS production by complex I and by complex III is differently affected by buffer pH and Ca2+ loading with mPTP opening. The study suggests that changes in the levels of cytosolic Ca2+ and pH during IR alter the relative amounts of ROS produced at mitochondrial respiratory complex I and complex III. PMID:25805998

Prevalence and direct costs of emergency department visits and hospitalizations for selected diseases that can be transmitted by water, United States.

PubMed

Adam, E A; Collier, S A; Fullerton, K E; Gargano, J W; Beach, M J

2017-10-01

National emergency department (ED) visit prevalence and costs for selected diseases that can be transmitted by water were estimated using large healthcare databases (acute otitis externa, campylobacteriosis, cryptosporidiosis, Escherichia coli infection, free-living ameba infection, giardiasis, hepatitis A virus (HAV) infection, Legionnaires' disease, nontuberculous mycobacterial (NTM) infection, Pseudomonas-related pneumonia or septicemia, salmonellosis, shigellosis, and vibriosis or cholera). An estimated 477,000 annual ED visits (95% CI: 459,000-494,000) were documented, with 21% (n = 101,000, 95% CI: 97,000-105,000) resulting in immediate hospital admission. The remaining 376,000 annual treat-and-release ED visits (95% CI: 361,000-390,000) resulted in $194 million in annual direct costs. Most treat-and-release ED visits (97%) and costs ($178 million/year) were associated with acute otitis externa. HAV ($5.5 million), NTM ($2.3 million), and salmonellosis ($2.2 million) were associated with next highest total costs. Cryptosporidiosis ($2,035), campylobacteriosis ($1,783), and NTM ($1,709) had the highest mean costs per treat-and-release ED visit. Overall, the annual hospitalization and treat-and-release ED visit costs associated with the selected diseases totaled $3.8 billion. As most of these diseases are not solely transmitted by water, an attribution process is needed as a next step to determine the proportion of these visits and costs attributable to waterborne transmission.

Causes of Stranding and Mortality, and Final Disposition of Loggerhead Sea Turtles (Caretta caretta) Admitted to a Wildlife Rehabilitation Center in Gran Canaria Island, Spain (1998-2014): A Long-Term Retrospective Study

PubMed Central

Orós, Jorge; Montesdeoca, Natalia; Camacho, María; Arencibia, Alberto; Calabuig, Pascual

2016-01-01

Aims The aims of this study were to analyze the causes of stranding of 1,860 loggerhead turtles (Caretta caretta) admitted at the Tafira Wildlife Rehabilitation Center in Gran Canaria Island, Spain, from 1998 to 2014, and to analyze the outcomes of the rehabilitation process to allow meaningful auditing of its quality. Methods Primary causes of morbidity were classified into seven categories: entanglement in fishing gear and/or plastics, ingestion of hooks and monofilament lines, trauma, infectious disease, crude oil, other causes, and unknown/undetermined. Final dispositions were calculated as euthanasia (Er), unassisted mortality (Mr), and release (Rr) rates. Time to death (Td) for euthanized and dead turtles, and length of stay for released (Tr) turtles were evaluated. Results The most frequent causes of morbidity were entanglement in fishing gear and/or plastics (50.81%), unknown/undetermined (20.37%), and ingestion of hooks (11.88%). The final disposition of the 1,634 loggerhead turtles admitted alive were: Er = 3.37%, Mr = 10.34%, and Rr = 86.29%. Er was significantly higher in the trauma category (18.67%) compared to the other causes of admission. The highest Mr was observed for turtles admitted due to trauma (30.67%). The highest Rr was observed in the crude oil (93.87%) and entanglement (92.38%) categories. The median Tr ranged from 12 days (unknown) to 70 days (trauma). Conclusions This survey is the first large-scale epidemiological study on causes of stranding and mortality of Eastern Atlantic loggerheads and demonstrates that at least 71.72% of turtles stranded due to anthropogenic causes. The high Rr (86.29%) emphasizes the importance of marine rehabilitation centers for conservation purposes. The stratified analysis by causes of admission of the three final disposition rates, and the parameters Td and Tr should be included in the outcome research of the rehabilitation process of sea turtles in order to allow comparative studies between marine rehabilitation centers around the world. PMID:26901623

Causes of Stranding and Mortality, and Final Disposition of Loggerhead Sea Turtles (Caretta caretta) Admitted to a Wildlife Rehabilitation Center in Gran Canaria Island, Spain (1998-2014): A Long-Term Retrospective Study.

PubMed

Orós, Jorge; Montesdeoca, Natalia; Camacho, María; Arencibia, Alberto; Calabuig, Pascual

2016-01-01

The aims of this study were to analyze the causes of stranding of 1,860 loggerhead turtles (Caretta caretta) admitted at the Tafira Wildlife Rehabilitation Center in Gran Canaria Island, Spain, from 1998 to 2014, and to analyze the outcomes of the rehabilitation process to allow meaningful auditing of its quality. Primary causes of morbidity were classified into seven categories: entanglement in fishing gear and/or plastics, ingestion of hooks and monofilament lines, trauma, infectious disease, crude oil, other causes, and unknown/undetermined. Final dispositions were calculated as euthanasia (Er), unassisted mortality (Mr), and release (Rr) rates. Time to death (Td) for euthanized and dead turtles, and length of stay for released (Tr) turtles were evaluated. The most frequent causes of morbidity were entanglement in fishing gear and/or plastics (50.81%), unknown/undetermined (20.37%), and ingestion of hooks (11.88%). The final disposition of the 1,634 loggerhead turtles admitted alive were: Er = 3.37%, Mr = 10.34%, and Rr = 86.29%. Er was significantly higher in the trauma category (18.67%) compared to the other causes of admission. The highest Mr was observed for turtles admitted due to trauma (30.67%). The highest Rr was observed in the crude oil (93.87%) and entanglement (92.38%) categories. The median Tr ranged from 12 days (unknown) to 70 days (trauma). This survey is the first large-scale epidemiological study on causes of stranding and mortality of Eastern Atlantic loggerheads and demonstrates that at least 71.72% of turtles stranded due to anthropogenic causes. The high Rr (86.29%) emphasizes the importance of marine rehabilitation centers for conservation purposes. The stratified analysis by causes of admission of the three final disposition rates, and the parameters Td and Tr should be included in the outcome research of the rehabilitation process of sea turtles in order to allow comparative studies between marine rehabilitation centers around the world.

A MODEL FOR FISSION-GAS RELEASE FROM POROUS FUELS IN LOW-PERMEABILITY CONTAINERS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prados, J.W.

1961-08-25

A simple mathematical model was developed to describe the steady-state release rate of gaseous fission products from porous ceramic fuels in low- permeability containers. The resulting equations are used to analyze experimental release rate results obtained from a UC/sub 2/-fueled graphite fuel body enclosed in a low-permeability impregnated graphite container. The relative release rates of the fission-product species Kr/sup 85m/, Kr/sup 88/, and Xe/sup 133/ were predicted with reasonable success. Absolute-rate predictions were not possible due to lack of information on true permeability and porosity profiles in the graphite container. (auth)

Diffusion Performance of Fertilizer Nutrient through Polymer Latex Film.

PubMed

An, Di; Yang, Ling; Liu, Boyang; Wang, Ting-Jie; Kan, Chengyou

2017-12-20

Matching the nutrient release rate of coated fertilizer with the nutrient uptake rate of the crop is the best way to increase the utilization efficiency of nutrients and reduce environmental pollution from the fertilizer. The diffusion property and mechanism of nutrients through the film are the theoretical basis for the product pattern design of coated fertilizers. For the coated fertilizer with a single-component nutrient, an extended solution-diffusion model was used to describe the difference of nutrient release rate, and the release rate is proportional to the permeation coefficient and the solubility of the nutrient. For the double- and triple-component fertilizer of N-K, N-P, and N-P-K, because of the interaction among nutrient molecules and ions, the release rates of different nutrients were significantly affected by the components in the composite fertilizer. Coating the single-component fertilizer (i.e., nitrogen fertilizer, phosphate fertilizer, and potash fertilizer) first and subsequently bulk blending is expected to be a promising way to adjust flexibly the nutrient release rate to meet the nutrient uptake rate of the crop.

Controlled release of silyl ether camptothecin from thiol-ene click chemistry-functionalized mesoporous silica nanoparticles.

PubMed

Yan, Yue; Fu, Jie; Wang, Tianfu; Lu, Xiuyang

2017-03-15

As efficient drug carriers, stimuli-responsive mesoporous silica nanoparticles are at the forefront of research on drug delivery systems. An acid-responsive system based on silyl ether has been applied to deliver a hybrid prodrug. Thiol-ene click chemistry has been successfully utilized for tethering this prodrug to mesoporous silica nanoparticles. Here, by altering the steric bulk of the substituent on the silicon atom, the release rate of a model drug, camptothecin, was controlled. The synthesized drug delivery system was investigated by analytical methods to confirm the functionalization and conjugation of the mesoporous silica nanoparticles. Herein, trimethyl silyl ether and triethyl silyl ether were selected to regulate the release rate. Under normal plasma conditions (pH 7.4), both types of camptothecin-loaded mesoporous silica nanoparticles (i.e., MSN-Me-CPT and MSN-Et-CPT) did not release the model drug. However, under in vitro acidic conditions (pH 4.0), based on a comparison of the release rates, camptothecin was released from MSN-Me-CPT more rapidly than from MSN-Et-CPT. To determine the biocompatibility of the modified mesoporous silica nanoparticles and the in vivo camptothecin uptake behavior, MTT assays with cancer cells and confocal microscopy observations were conducted, with positive results. These functionalized nanoparticles could be useful in clinical treatments requiring controlled drug release. As the release rate of drug from drug-carrier plays important role in therapy effects, trimethyl silyl ether (TMS) and triethyl silyl ether (TES) were selected as acid-sensitive silanes to control the release rates of model drugs conjugated from MSNs by thiol-ene click chemistry. The kinetic profiles of TMS and TES materials have been studied. At pH 4.0, the release of camptothecin from MSN-Et-CPT occurred after 2h, whereas MSN-Me-CPT showed immediate drug release. The results showed that silyl ether could be used to control release rates of drugs from MSNs under acid environment, which could be useful in clinical treatments requiring controlled drug release. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Field evaluation of plant odor and pheromonal combinations for attracting plum curculios.

PubMed

Piñero, Jaime C; Prokopy, Ronald J

2003-12-01

The attractiveness of different synthetic host odors and a synthetic aggregation pheromone (grandisoic acid [GA]) to overwintered adult plum curculios (PCs), Conotrachelus nenuphar (Herbst) (Coleoptera: Curculionidae), was examined using two types of traps (sticky panels and black pyramids) placed in border areas surrounding an unsprayed section of an apple orchard in Massachusetts. In 2001, we evaluated the response of PCs to three synthetic fruit volatiles (benzaldehyde [BEN], ethyl isovalerate [EIV], and limonene [LIM]) assessed alone and in combination with GA, as well as the response to GA alone and a no-odor (control) treatment. BEN was the only host volatile that synergized the response of PCs to GA for both trap types. For both trap types, GA was as attractive to PCs as a single component as when in combination with either EIV or LIM. In 2002, four release rates of BEN (0, 2.5, 10, and 40 mg/day) and two release rates of GA (1 and 2 mg/day) were evaluated for attractiveness to PCs using panel and pyramid traps. For panel traps, an increase in amount of GA released (from 1 to 2 mg/day) was associated with a 35% increase in captures. However, PC captures by pyramid traps were similar regardless of the amount of GA released. For panel traps, 10 and 40 mg/day of BEN were the most attractive release rates regardless of the amount of GA released. For pyramid traps baited with GA. PC captures were enhanced by the presence of BEN, regardless of release rate. In 2003, GA at 1 mg/day + BEN at 80 mg/day of release did not enhance PC captures by panel traps relative to lower release rates of BEN. Pyramid traps releasing GA at 1 mg/day performed best when baited with BEN at 10 mg/day of release; a release rate of 80 mg/day of BEN decreased the attractiveness of the binary combination of BEN + GA. Combined results suggest that BEN at 10 mg/day + GA at 1 mg/day of release constitutes an attractive lure that may improve the effectiveness of monitoring traps for PCs.

Soil respiration in the cold desert environment of the Colorado Plateau (USA): Abiotic regulators and thresholds

USGS Publications Warehouse

Fernandez, D.P.; Neff, J.C.; Belnap, J.; Reynolds, R.L.

2006-01-01

Decomposition is central to understanding ecosystem carbon exchange and nutrient-release processes. Unlike mesic ecosystems, which have been extensively studied, xeric landscapes have received little attention; as a result, abiotic soil-respiration regulatory processes are poorly understood in xeric environments. To provide a more complete and quantitative understanding about how abiotic factors influence soil respiration in xeric ecosystems, we conducted soil- respiration and decomposition-cloth measurements in the cold desert of southeast Utah. Our study evaluated when and to what extent soil texture, moisture, temperature, organic carbon, and nitrogen influence soil respiration and examined whether the inverse-texture hypothesis applies to decomposition. Within our study site, the effect of texture on moisture, as described by the inverse texture hypothesis, was evident, but its effect on decomposition was not. Our results show temperature and moisture to be the dominant abiotic controls of soil respiration. Specifically, temporal offsets in temperature and moisture conditions appear to have a strong control on soil respiration, with the highest fluxes occurring in spring when temperature and moisture were favorable. These temporal offsets resulted in decomposition rates that were controlled by soil moisture and temperature thresholds. The highest fluxes of CO2 occurred when soil temperature was between 10 and 16??C and volumetric soil moisture was greater than 10%. Decomposition-cloth results, which integrate decomposition processes across several months, support the soil-respiration results and further illustrate the seasonal patterns of high respiration rates during spring and low rates during summer and fall. Results from this study suggest that the parameters used to predict soil respiration in mesic ecosystems likely do not apply in cold-desert environments. ?? Springer 2006.

An evaluation of the Motion Picture Association of America's treatment of violence in PG-, PG-13-, and R-rated films.

PubMed

Jenkins, Lucille; Webb, Theresa; Browne, Nick; Afifi, A A; Kraus, Jess

2005-05-01

The purpose of this study was to determine whether the Motion Picture Association of America's ratings system distinguishes among the 3 primary rating categories (PG, PG-13, and R) with respect to violence based on a study of the 100 top-grossing films of 1994. The Motion Picture Association of America assigns age-based ratings for every film that is released in the United States accompanied by the reasons for the rating. A data abstraction instrument was designed to code each act of violence within the sample of 100 films. A series of Poisson regression models were used to examine the association among rating, seriousness of violence, and primary reason for the rating assignment. The total average number of violent acts within each film by rating category increased from PG (14) to PG-13 (20) to R (32). However, using results from the Poisson models, it is clear that the rating does not predict the frequency of violence in films. For all 3 rating categories, the predicted number of violent acts is almost identical for films with violence as a primary descriptor and films with the highest level of seriousness (R = 62.4 acts, PG-13 = 55.2 acts, and PG = 56.1 acts). The regression analysis shows that the rating does not predict the frequency of violence that occurs in films. Frequency of violence alone is not the most important criterion for the assignment of rating. The content descriptors and average seriousness of films are better measures of the violence than rating assignment.

The assessment of ionising radiation impact on the cooling pond freshwater ecosystem non-human biota from the Ignalina NPP operation beginning to shut down and initial decommissioning.

PubMed

Mazeika, J; Marciulioniene, D; Nedveckaite, T; Jefanova, O

2016-01-01

The radiological doses to non-human biota of freshwater ecosystem in the Ignalina NPP cooling pond - Lake Druksiai were evaluated for several cases including the plant's operation period and initial decommissioning activities, using the ERICA 1.2 code with IAEA SRS-19 models integrated approach and tool. Among the Lake Druksiai freshwater ecosystem reference organisms investigated the highest exposure dose rate was determined for bottom fauna - benthic organisms (mollusc-bivalves, crustaceans, mollusc-gastropods, insect larvae), and among the other reference organisms - for vascular plants. The mean and maximum total dose rate values due to anthropogenic radionuclide ionising radiation impact in all investigated cases were lower than the ERICA screening dose rate value of 10 μGy/h. The main exposure of reference organisms as a result of Ignalina NPP former effluent to Lake Druksiai is due to ionizing radiation of radionuclides (60)Co and (137)Cs, of predicted releases to Lake Druksiai during initial decommissioning period - due to radionuclides (60)Co, (134)Cs and (137)Cs, and as a result of predicted releases to Lake Druksiai from low- and intermediate-level short-lived radioactive waste disposal site in 30-100 year period - due to radionuclides (99)Tc and (3)H. The risk quotient expected values in all investigated cases were <1, and therefore the risk to non-human biota can be considered negligible with the exception of a conservative risk quotient for insect larvae. Radiological protection of non-human biota in Lake Druksiai, the Ignalina NPP cooling pond, is both feasible and acceptable. Copyright © 2015 Elsevier Ltd. All rights reserved.

Influence of rock composition on the geochemistry of stream and spring waters from mountainous watersheds in the Gunnison, Uncompahgre, and Grand Mesa National Forests, Colorado

USGS Publications Warehouse

Miller, William Roger

2002-01-01

The ranges of geochemical baselines for stream and spring waters were determined and maps were constructed showing acid-neutralizing capacity and potential release of total dissolved solids for streams and spring waters for watersheds underlain by each of ten different rock composition types in the Gunnison, Uncompahgre, and Grand Mesa National Forests, Colorado (GMUG). Water samples were collected in mountainous headwater watersheds that have comparatively high precipitation and low evapotranspiration rates and that generally lack extensive ground-water reservoirs. Mountainous headwaters react quickly to changes in input of water from rain and melting snow and they are vulnerable to anthropogenic impact. Processes responsible for the control and mobility of elements in the watersheds were investigated. The geochemistry of water from the sampled watersheds in the GMUG, which are underlain by rocks that are relatively unmineralized, is compared to the geochemistry of water from the mineralized Redcloud Peak area. The water with the highest potential for release of total dissolved solids is from watersheds that are underlain by Paleozoic sedimentary rocks; that high potential is caused primarily by gypsum in those rocks. Water that has the highest acid-neutralizing capacity is from watersheds that are underlain by Paleozoic sedimentary rocks. The water from watersheds underlain by the Mancos Shale has the next highest acid-neutralizing capacity. Water that has the lowest acid-neutralizing capacity is from watersheds that are underlain by Tertiary ash-flow tuff. Tertiary sedimentary rocks containing oil shale, the Mesavede Formation containing coal, and the Mancos Shale all contain pyrite with elevated metal contents. In these mountainous head-water areas, water from watersheds underlain by these rock types is only slightly impacted by oxidation of pyrite, and over-all it is of good chemical quality. These geochemical baselines demonstrate the importance of rock composition in determining the types of waters that are in the headwater areas. The comparison of these geochemical baselines to later geochemical base-lines will allow recognition of any significant changes in water quality that may occur in the future.

Ferulic Acid-Based Polymers with Glycol Functionality as a Versatile Platform for Topical Applications.

PubMed

Ouimet, Michelle A; Faig, Jonathan J; Yu, Weiling; Uhrich, Kathryn E

2015-09-14

Ferulic acid-based polymers with aliphatic linkages have been previously synthesized via solution polymerization methods, yet they feature relatively slow ferulic acid release rates (∼11 months to 100% completion). To achieve a more rapid release rate as required in skin care formulations, ferulic acid-based polymers with ethylene glycol linkers were prepared to increase hydrophilicity and, in turn, increase ferulic acid release rates. The polymers were characterized using nuclear magnetic resonance and Fourier transform infrared spectroscopies to confirm chemical composition. The molecular weights, thermal properties (e.g., glass transition temperature), and contact angles were also obtained and the polymers compared. Polymer glass transition temperature was observed to decrease with increasing linker molecule length, whereas increasing oxygen content decreased polymer contact angle. The polymers' chemical structures and physical properties were shown to influence ferulic acid release rates and antioxidant activity. In all polymers, ferulic acid release was achieved with no bioactive decomposition. These polymers demonstrate the ability to strategically release ferulic acid at rates and concentrations relevant for topical applications such as skin care products.

Distribution, behavior, and transport of inorganic and methylmercury in a high gradient stream

USGS Publications Warehouse

Flanders, J.R.; Turner, R.R.; Morrison, T.; Jensen, R.; Pizzuto, J.; Skalak, K.; Stahl, R.

2010-01-01

Concentrations of Hg remain elevated in physical and biological media of the South River (Virginia, USA), despite the cessation of the industrial use of Hg in its watershed nearly six decades ago, and physical characteristics that would not seem to favor Hg(II)-methylation. A 3-a study of inorganic Hg (IHg) and methylmercury (MeHg) was conducted in physical media (soil, sediment, surface water, porewater and soil/sediment extracts) to identify non-point sources, transport mechanisms, and potential controls on Hg(II)-methylation. Data collected from surface water and sediment indicate that the majority of the non-point sources of IHg to the South River are within the first 14. km downstream from the historic point source. Partitioning data indicate that particle bound IHg is introduced in this reach, releasing dissolved and colloidal bound IHg, which is transported downstream. Extraction experiments revealed that floodplain soils released a higher fraction of their IHg content in aqueous extractions than fine-grained sediment (FGS). Based on ultrafiltration [<5000 nominal molecular weight cutoff (NMWC)] the majority of soil IHg released was colloidal in nature, providing evidence for the continued evolution of IHg for Hg(II)-methylation from soil. Strong seasonal patterns in MeHg concentrations were observed in surface water and sediment. The highest concentrations of MeHg in surface water were observed at moderate temperatures, suggesting that other factors limit net Hg(II)-methylation. Seasonal changes in sediment organic content and the fraction of 1. N KOH-extractable THg were also observed and may be important factors in controlling net Hg(II)-methylation rates. Sulfate concentrations in surface water are low and the evidence suggests that Fe reduction may be an important Hg(II)-methylation process. The highest sediment MeHg concentrations were observed in habitats with large amounts of FGS, which are more prevalent in the upper half of the study area due to the lower hydrologic gradient and agricultural impacts. Past and present land use practices and other geomorphologic controls contribute to the erosion of banks and accumulation of fine-grained sediment in this section of the river, acting as sources of IHg. ?? 2010 Elsevier Ltd.

The effect of radiopacifiers agents on pH, calcium release, radiopacity, and antimicrobial properties of different calcium hydroxide dressings.

PubMed

Ordinola-Zapata, Ronald; Bramante, Clovis Monteiro; García-Godoy, Franklin; Moldauer, Bertram Ivan; Gagliardi Minotti, Paloma; Tercília Grizzo, Larissa; Duarte, Marco Antonio Hungaro

2015-07-01

The aim of this study was to evaluate the antimicrobial activity, pH level, calcium ion release, and radiopacity of calcium hydroxide pastes associated with three radiopacifying agents (iodoform, zinc oxide, and barium sulfate). For the pH and calcium release tests, 45 acrylic teeth were utilized and immersed in ultrapure water. After 24 h, 72 h, and 7 days the solution was analyzed by using a pH meter and an atomic absorption spectrophotometer. Polyethylene tubes filled with the pastes were used to perform the radiopacity test. For the antimicrobial test, 25 dentin specimens were infected intraorally in order to induce the biofilm colonization and treated with the pastes for 7 days. The Live/Dead technique and a confocal microscope were used to obtain the ratio of live cells. Parametric and nonparametric statistical tests were performed to show differences among the groups (P < 0.05). The pH analysis at 7 days showed significant differences (P < 0.05) among the groups. No differences among the pastes were found in the calcium release test on the 7th day (P > 0.05). The calcium hydroxide/iodoform samples had the highest radiopacity and antimicrobial activity against the biofilm-infected dentin in comparison to the other pastes (P < 0.05). Calcium hydroxide mixed with 17% iodoform and 35% propylene glycol into a paste had the highest pH, calcium ion release, radiopacity, and the greatest antimicrobial action versus similar samples mixed with BaSO4 or ZnO. © 2015 Wiley Periodicals, Inc.

Hydration of dicalcium silicate and diffusion through neo-formed calcium-silicate-hydrates at weathered surfaces control the long-term leaching behaviour of basic oxygen furnace (BOF) steelmaking slag.

PubMed

Stewart, Douglas I; Bray, Andrew W; Udoma, Gideon; Hobson, Andrew J; Mayes, William M; Rogerson, Mike; Burke, Ian T

2018-04-01

Alkalinity generation and toxic trace metal (such as vanadium) leaching from basic oxygen furnace (BOF) steel slag particles must be properly understood and managed by pre-conditioning if beneficial reuse of slag is to be maximised. Water leaching under aerated conditions was investigated using fresh BOF slag at three different particle sizes (0.5-1.0, 2-5 and 10 × 10 × 20 mm blocks) and a 6-month pre-weathered block. There were several distinct leaching stages observed over time associated with different phases controlling the solution chemistry: (1) free-lime (CaO) dissolution (days 0-2); (2) dicalcium silicate (Ca 2 SiO 4 ) dissolution (days 2-14) and (3) Ca-Si-H and CaCO 3 formation and subsequent dissolution (days 14-73). Experiments with the smallest size fraction resulted in the highest Ca, Si and V concentrations, highlighting the role of surface area in controlling initial leaching. After ~2 weeks, the solution Ca/Si ratio (0.7-0.9) evolved to equal those found within a Ca-Si-H phase that replaced dicalcium silicate and free-lime phases in a 30- to 150-μm altered surface region. V release was a two-stage process; initially, V was released by dicalcium silicate dissolution, but V also isomorphically substituted for Si into the neo-formed Ca-Si-H in the alteration zone. Therefore, on longer timescales, the release of V to solution was primarily controlled by considerably slower Ca-Si-H dissolution rates, which decreased the rate of V release by an order of magnitude. Overall, the results indicate that the BOF slag leaching mechanism evolves from a situation initially dominated by rapid hydration and dissolution of primary dicalcium silicate/free-lime phases, to a slow diffusion limited process controlled by the solubility of secondary Ca-Si-H and CaCO 3 phases that replace and cover more reactive primary slag phases at particle surfaces.

Do nitric oxide donors mimic endogenous NO-related response in plants?

PubMed

Floryszak-Wieczorek, J; Milczarek, G; Arasimowicz, M; Ciszewski, A

2006-11-01

Huge advances achieved recently in elucidating the role of NO in plants have been made possible by the application of NO donors. However, the application of NO to plants in various forms and doses should be subjected to detailed verification criteria. Not all metabolic responses induced by NO donors are reliable and reproducible in other experimental designs. The aim of the presented studies was to investigate the half-life of the most frequently applied donors (SNP, SNAP and GSNO), the rate of NO release under the influence of light and reducing agents. At a comparable donor concentration (500 microM) and under light conditions the highest rate of NO generation was found for SNAP, followed by GSNO and SNP. The measured half-life of the donor in the solution was 3 h for SNAP, 7 h for GSNO and 12 h for SNP. A temporary lack of light inhibited NO release from SNP, both in the solution and SNP-treated leaf tissue, which was measured by the electrochemical method. Also a NO, selective fluorescence indicator DAF-2DA in leaves supplied with different donors showed green fluorescence spots in the epidermal cells mainly in the light. SNP as a NO donor was the most photosensitive. The activity of PAL, which plays an important role in plant defence, was also activated by SNP in the light, not in the dark. S-nitrosothiols (SNAP and GSNO) also underwent photodegradation, although to a lesser degree than SNP. Additionally, NO generation capacity from S-nitrosothiols was shown in the presence of reducing agents, i.e. ascorbic acid and GSH, and the absence of light. The authors of this paper would like to polemicize with the commonly cited statement that "donors are compounds that spontaneously break down to release NO" and wish to point out the fact that the process of donor decomposition depends on the numerous external factors. It may be additionally stimulated or inhibited by live plant tissue, thus it is necessary to take into consideration these aspects and monitor the amount of NO released by the donor.

Comparative drug release measurements in limited amounts of liquid: a suppository formulation study.

PubMed

Welch, Ken; Ek, Ragnar; Strømme, Maria

2006-07-01

A novel method for the investigation of drug formulations in limited liquid volumes is presented. The experimental setup consists of a measurement cell containing an absorbent sponge cloth placed between two parallel electrodes. Conductivity measurements are used to monitor the drug release from the dosage form. By varying the amount of water contained in the absorbent cloth surrounding the dosage form, it is possible to measure the drug release performance of the dosage form in very limited amounts of water. The method was employed to test four different tablet formulations consisting of the model drug NaCl incorporated in excipient matrices of hard fat, polyethylene glycol, microcrystalline cellulose and a mixture of microcrystalline cellulose and croscarmellose sodium (Ac-Di-Sol). The drug release rates of the different formulations in limited water volumes differed markedly from the release rates in an excess of water. Whereas the release rates from all tablet types in an excess of water showed only minor differences among the tablet types, the release rates from the tablets formulated with disintegrating excipients were clearly superior in limited water volumes. The developed method for drug release in limited volumes of liquid should be suitable for evaluation of rectal dosage forms.

Release of antioxidant capacity from five plant foods during a multistep enzymatic digestion protocol.

PubMed

Papillo, Valentina Azzurra; Vitaglione, Paola; Graziani, Giulia; Gokmen, Vural; Fogliano, Vincenzo

2014-05-07

This study aimed at elucidating the influence of food matrix on the release of antioxidant activity from five plant foods (apple, spinach, walnut, red bean, and whole wheat). To this purpose a protocol based on sequential enzymatic digestion was adopted. The total antioxidant capacity (TAC) of both solubilized and insoluble materials was measured at each step. Results showed that the overall TAC obtained by enzyme treatments was usually higher than that obtained by chemical extraction-based methods. In apple most of the TAC was released upon water washing and after pepsin treatment, whereas in spinach, beans, and whole wheat the TAC released by treatments with bacterial enzymes was prominent. Walnut had the highest TAC value, which was mainly released after pancreatin treatment. Therefore, the enzyme treatment is fundamental to estimate the overall potential TAC of foods having a high amount of polyphenols bound to dietary fiber or entrapped in the food matrix.

MR-DTI and PET multimodal imaging of dopamine release within subdivisions of basal ganglia

NASA Astrophysics Data System (ADS)

Tziortzi, A.; Searle, G.; Tsoumpas, C.; Long, C.; Shotbolt, P.; Rabiner, E.; Jenkinson, M.; Gunn, R. N.

2011-09-01

The basal ganglia is a group of anatomical nuclei, functionally organised into limbic, associative and sensorimotor regions, which plays a central role in dopamine related neurological and psychiatric disorders. In this study, we combine two imaging modalities to enable the measurement of dopamine release in functionally related subdivisions of the basal ganglia. [11C]-(+)-PHNO Positron Emission Tomography (PET) measurements in the living human brain pre- and post-administration of amphetamine allow for the estimation of regional dopamine release. Combined Magnetic Resonance Diffusion Tensor Imaging (MR-DTI) data allows for the definition of functional territories of the basal ganglia from connectivity information. The results suggest that there is a difference in dopamine release among the connectivity derived functional subdivisions. Dopamine release is highest in the limbic area followed by the sensorimotor and then the associative area with this pattern reflected in both striatum and pallidum.

Low-molecular-weight organoiodine and organobromine compounds released by polar macroalgae--the influence of abiotic factors.

PubMed

Laturnus, F; Giese, B; Wiencke, C; Adams, F C

2000-01-01

The influence of temperature, light, salinity and nutrient availability on the release of volatile halogenated hydrocarbons was investigated in the Antarctic red macroalgal species Gymnogongrus antarcticus Skottsberg. Compared to standard culture condition, an increase in the release rates of iodocompounds was generally found for the exposure of the alga to altered environmental conditions. Macroalgae exhibited higher release rates after adaptation for two months to the changed factors, than after short-term exposure. Monitoring the release rates during a 24 h incubation period (8.25 h light, 15.75 h darkness) showed that changes between light and dark periods had no influence on the release of volatile halocarbons. Compounds like bromoform and 1-iodobutane exhibited constant release rates during the 24 h period. The formation mechanisms and biological role of volatile organohalogens are discussed. Although marine macroalgae are not considered to be the major source of biogenically-produced volatile organohalogens, they contribute significantly to the bromine and iodine cycles in the environment. Under possible environmental changes like global warming and uncontrolled entrophication of the oceans their significance may be increase.

Surveillance of Diversion and Nonmedical Use of Extended-Release Prescription Amphetamine and Oral Methylphenidate in the United States

PubMed Central

Sembower, Mark A.; Ertischek, Michelle D.; Buchholtz, Chloe; Dasgupta, Nabarun; Schnoll, Sidney H.

2013-01-01

This article examines rates of nonmedical use and diversion of extended-release amphetamine and extended-release oral methylphenidate in the United States. Prescription dispensing data were sourced from retail pharmacies. Nonmedical use data were collected from the Researched Abuse, Diversion and Addiction-Related Surveillance (RADARS) System Drug Diversion Program and Poison Center Program. Drug diversion trends nearly overlapped for extended-release amphetamine and extended-release oral methylphenidate. Calls to poison centers were generally similar; however, calls regarding extended-release amphetamine trended slightly lower than those for extended-release oral methylphenidate. Data suggest similar diversion and poison center call rates for extended-release amphetamine and extended-release oral methylphenidate. PMID:23480245

Estimations of direct release rate of 137Cs and 90Sr to the ocean from the Fukushima Dai-ichi Nuclear Power Plant for five-and-a-half years

NASA Astrophysics Data System (ADS)

Tsumune, Daisuke; Aoyama, Michio; Tsubono, Takaki; Misumi, Kazuhiro; Tateda, Yutaka

2017-04-01

A series of accidents at the Fukushima Dai-ichi Nuclear Power Plant (1F NPP) following the earthquake and tsunami of 11 March 2011 resulted in the release of radioactive materials to the ocean by two major pathways, direct release from the accident site and atmospheric deposition. Additional release pathways by river input and runoff from 1F NPP site with precipitation and were also effective for coastal zone in the specific periods before starting direct release on March 26 2011. Direct release from 1F NPP site is dominant one year after the accident. We estimated the direct release rate of 137Cs and 90Sr for more than five-and-a-half years after the accident by the Regional Ocean Model System (ROMS). Direct release rate of 137Cs were estimated for five-and-a-half years after the accident by comparing simulated results and measured activities adjacent to the 1F NPP site(at 5,6 discharge and south discharge). Directly release rate of 137Cs was estimated to be the order of magnitude of 1014 Bq/day and decreased exponentially with time to be the order of magnitude of 109 Bq/day by the end of September 2016. Estimated direct release rate have exponentially reduced with constant rate since November 2011. Apparent half-life of direct release rate was estimated to be 346 days. The estimated total amounts of directly released 137Cs was 3.7±0.7 PBq for five and a half years. Simulated 137Cs activities attributable to direct release were in good agreement with observed activities, a result that implies the estimated direct release rate was reasonable. Simulated 137Cs activity affected off coast in the Fukushima prefecture. We used the measured 137Cs activities by the Tokyo Electric Power Company (TEPCO) for the estimation of direct release. The sea water samples were corrected from the coast. The averaged 137Cs activities from November 2013 to June 2016 were 391 and 383 Bq/m3 at 5,6 discharge and south discharge, respectively. The averaged 137Cs activities measured by the Nuclear Regulation Agency (NRA) is about five times smaller than the one by the TEPCO because the NRA corrected seawater samples at 300-500m offshore by ship. Horizontal resolution of the model was 1km x 1km, therefore it is important to consider the difference of activities in the sub-grid scale for the detailed estimations of direct release. 90Sr/137Cs activity ratio measured adjacent to the 1F NPP is variable with time. The 90Sr/137Cs activity ratio was 0.62 due to the global fallout before the accident. The 90Sr/137Cs activity ratio decreased to 0.01 after the accident before April 2011. And the ratio increased to 1 by September 2013. And then the ratio decreased to 0.1-1. After October 2015, the ratio decreased to 0.1-0.2. Directly release rate of 90Sr was estimated to be the order of magnitude of 1012 Bq/day and decreased to the order of magnitude of 108 Bq/day by the end of September 2016. The estimated total amounts of directly released 90Sr was 35 ± 7 TBq.

Stress and preterm labor and birth in Black women.

PubMed

Gennaro, Susan; Shults, Justine; Garry, David J

2008-01-01

To examine (a) 3 commonly used measures of stress during pregnancy, (b) changes in stress over time to determine when stress is highest, and (c) whether any of the stress measures predict who will deliver preterm in pregnant Black women. Prospective descriptive study. Perinatal evaluation center and outpatient clinics of a teaching hospital in the northeast. Fifty-nine Black women: 39 were recruited in preterm labor from a Perinatal Evaluation Center, and 20 experiencing healthy pregnancies were recruited from the prenatal clinic. Stress was measured using 2 paper and pencil tests (the Prenatal Distress Questionnaire and the Perceived Stress Scale) and corticotropin-releasing hormone. There was not a high correlation between stress measures. Stress at 28 weeks as measured by Prenatal Distress Questionnaire and Perceived Stress Scale was at its highest, but corticotropin-releasing hormone increased to 32 weeks and then decreased. Perceived stress, prenatal distress, and corticotropin-releasing hormone do not all appear to be measuring the same phenomenon. Screening for stress in Black women at 28 weeks requires further research as perceived stress levels in Black women experiencing preterm labor around 28 weeks differentiated women who delivered preterm infants from Black women who delivered at term.

Pretreatment and hydrolysis methods for recovery of fermentable sugars from de-oiled Jatropha waste.

PubMed

Kumar, Gopalakrishnan; Sen, Biswarup; Lin, Chiu-Yue

2013-10-01

The release of reducing sugars (RS) upon various pretreatments and hydrolysis methods from de-oiled Jatropha waste (DJW) was studied. The highest RS concentration of 12.9 g/L was observed at 10% enzyme hydrolysis. The next highest RS of 8.0 g/L and 7.8 g/L were obtained with 10% HCl and 2.5% H2SO4, respectively. The NaOH (2.5%), ultrasonication and heat (90°C for 60 min) treatments showed the RS concentration of 2.5 g/L, 1.1 g/L and 2.0 g/L, respectively. Autoclave treatment slightly enhanced the sugar release (0.9 g/L) compared to no treatment (0.7 g/L). Glucose release (11.4 g/L) peaked in enzyme hydrolysis. Enzyme treated acid unhydrolysed biomass showed 11.1 g/L RS. HCl and H2SO4 pretreatment gave maximal xylose (6.89 g/L and 6.16 g/L, respectively). Combined (acid and enzyme) hydrolysis employed was efficient and its subsequent batch hydrogen fermentation showed a production 3.1 L H2/L reactor. Copyright © 2013 Elsevier Ltd. All rights reserved.

Radionuclide observables for the Platte underground nuclear explosive test on 14 April 1962

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burnett, Jonathan L.; Milbrath, Brian D.

2016-11-01

Past nuclear weapons tests provide invaluable information for understanding the radionuclide observables and data quality objectives expected during an On-site Inspection (OSI) for the Comprehensive Nuclear-Test-Ban Treaty (CTBT). These radioactive signatures are complex and subject to spatial and temporal variability. The Platte Underground Nuclear Test on 14 April 1962 provides extensive environmental monitoring data that can be modelled and used to assess an OSI. The 1.6 kT test is especially useful as it released the highest amounts of recorded activity during Operation Nougat at the Nevada Test Site – now known as the Nevada National Security Site (NNSS). It hasmore » been estimated that 0.36% of the activity was released, and dispersed in a northerly direction. The deposition ranged from 1 x 10-11 to 1 x 10-9 of the atmospheric release (per m2), and has been used to evaluate a hypothetical OSI at 1 week to 2 years post-detonation. Radioactive decay reduces the activity of the 17 OSI relevant radionuclides by 99.7%, such that detection throughout the inspection is only achievable close to the explosion where deposition was highest.« less

Evaluating the combined effects of source zone mass release rates and aquifer heterogeneity on solute discharge uncertainty

NASA Astrophysics Data System (ADS)

de Barros, Felipe P. J.

2018-07-01

Quantifying the uncertainty in solute mass discharge at an environmentally sensitive location is key to assess the risks due to groundwater contamination. Solute mass fluxes are strongly affected by the spatial variability of hydrogeological properties as well as release conditions at the source zone. This paper provides a methodological framework to investigate the interaction between the ubiquitous heterogeneity of the hydraulic conductivity and the mass release rate at the source zone on the uncertainty of mass discharge. Through the use of perturbation theory, we derive analytical and semi-analytical expressions for the statistics of the solute mass discharge at a control plane in a three-dimensional aquifer while accounting for the solute mass release rates at the source. The derived solutions are limited to aquifers displaying low-to-mild heterogeneity. Results illustrate the significance of the source zone mass release rate in controlling the mass discharge uncertainty. The relative importance of the mass release rate on the mean solute discharge depends on the distance between the source and the control plane. On the other hand, we find that the solute release rate at the source zone has a strong impact on the variance of the mass discharge. Within a risk context, we also compute the peak mean discharge as a function of the parameters governing the spatial heterogeneity of the hydraulic conductivity field and mass release rates at the source zone. The proposed physically-based framework is application-oriented, computationally efficient and capable of propagating uncertainty from different parameters onto risk metrics. Furthermore, it can be used for preliminary screening purposes to guide site managers to perform system-level sensitivity analysis and better allocate resources.

Environmental Impacts by Fragments Released from Nanoenabled Products: A Multiassay, Multimaterial Exploration by the SUN Approach.

PubMed

Amorim, Mónica J B; Lin, Sijie; Schlich, Karsten; Navas, José M; Brunelli, Andrea; Neubauer, Nicole; Vilsmeier, Klaus; Costa, Anna L; Gondikas, Andreas; Xia, Tian; Galbis, Liliana; Badetti, Elena; Marcomini, Antonio; Hristozov, Danail; Kammer, Frank von der; Hund-Rinke, Kerstin; Scott-Fordsmand, Janeck J; Nel, André; Wohlleben, Wendel

2018-02-06

Nanoenabled products (NEPs) have numerous outdoor uses in construction, transportation or consumer scenarios, and there is evidence that their fragments are released in the environment at low rates. We hypothesized that the lower surface availability of NEPs fragment reduced their environmental effects with respect to pristine nanomaterials. This hypothesis was explored by testing fragments generated by intentional micronisation ("the SUN approach"; Nowack et al. Meeting the Needs for Released Nanomaterials Required for Further Testing: The SUN Approach. Environmental Science & Technology, 2016 (50), 2747). The NEPs were composed of four matrices (epoxy, polyolefin, polyoxymethylene, and cement) with up to 5% content of three nanomaterials (carbon nanotubes, iron oxide, and organic pigment). Regardless of the type of nanomaterial or matrix used, it was observed that nanomaterials were only partially exposed at the NEP fragment surface, indicating that mostly the intrinsic and extrinsic properties of the matrix drove the NEP fragment toxicity. Ecotoxicity in multiple assays was done covering relevant media from terrestrial to aquatic, including sewage treatment plant (biological activity), soil worms (Enchytraeus crypticus), and fish (zebrafish embryo and larvae and trout cell lines). We designed the studies to explore the possible modulation of ecotoxicity by nanomaterial additives in plastics/polymer/cement, finding none. The results support NEPs grouping by the matrix material regarding ecotoxicological effect during the use phase. Furthermore, control results on nanomaterial-free polymer fragments representing microplastic had no significant adverse effects up to the highest concentration tested.

Formulation and in vitro evaluation of theophylline matrix tablets prepared by direct compression: Effect of polymer blends

PubMed Central

El-Bagory, Ibrahim; Barakat, Nahla; Ibrahim, Mohamed A.; El-Enazi, Fouza

2011-01-01

The deformation mechanism of pharmaceutical powders, used in formulating directly compressed matrix tablets, affects the characteristics of the formed tablets. Three polymers of different deformation mechanisms were tested for their impact on theophylline directly compressed tablets namely Kollidon SR (KL SR, plastic deformation), Ethylcellulose (EC, elastic deformation) and Carnauba wax (CW, brittle deformation) at different compression forces. However, tablets based mainly on KL SR, the plastically deformed polymer (TN1) exhibited the highest hardness values compared to the other formulae which are based on either blends of KL SR with CW, the very brittle deformed polymer. The upper detected force for TN formulae and the lower punch force were found to dependent mainly on the powder deformation. This difference is attributed to the work done during the compression phase as well as the work lost during the decompression phase. Furthermore, the release profiles of TN from formulae TN2 and TN4 that are based on the composition (2KL SR:1EC) and (1KL SR:2EC), respectively, were consistent with different deformation mechanisms of KL SR and EC and on the physicochemical properties like the water absorptive capacity of EC. Upon increasing the weight ratio of KL SR (TN2), the release rate was greatly retarded (39.4%, 37.1%, 35.0% and 33.6% released after 8 h at 5, 10, 15 and 20 kN. PMID:24115902

Intelligent anticancer drug delivery performances of two poly(N-isopropylacrylamide)-based magnetite nanohydrogels.

PubMed

Poorgholy, Nahid; Massoumi, Bakhshali; Ghorbani, Marjan; Jaymand, Mehdi; Hamishehkar, Hamed

2018-08-01

This article evaluates the anticancer drug delivery performances of two nanohydrogels composed of poly(N-isopropylacrylamide-co-itaconic anhydride) [P(NIPAAm-co-IA)], poly(ethylene glycol) (PEG), and Fe 3 O 4 nanoparticles. For this purpose, the magnetite nanohydrogels (MNHGs) were loaded with doxorubicin hydrochloride (DOX) as a universal anticancer drug. The morphologies and magnetic properties of the DOX-loaded MNHGs were investigated using transmission electron microscopy (TEM) and vibrating-sample magnetometer (VSM), respectively. The sizes and zeta potentials (ξ) of the MNHGs and their corresponding DOX-loaded nanosystems were also investigated. The DOX-loaded MNHGs showed the highest drug release values at condition of 41 °C and pH 5.3. The drug-loaded MNHGs at physiological condition (pH 7.4 and 37 °C) exhibited negligible drug release values. In vitro cytotoxic effects of the DOX-loaded MNHGs were extensively evaluated through the assessing survival rate of HeLa cells using the MTT assay, and there in vitro cellular uptake into the mentioned cell line were examined using fluorescent microscopy and fluorescence-activated cell sorting (FACS) flow cytometry analyses. As the results, the DOX-loaded MNHG1 exhibited higher anticancer drug delivery performance in the terms of cytotoxic effect and in vitro cellular uptake. Thus, the developed MNHG1 can be considered as a promising de novo drug delivery system, in part due to its pH and thermal responsive drug release behavior as well as proper magnetite character toward targeted drug delivery.

Improvement of succinate production by release of end-product inhibition in Corynebacterium glutamicum.

PubMed

Chung, Soon-Chun; Park, Joon-Song; Yun, Jiae; Park, Jin Hwan

2017-03-01

Succinate is a renewable-based platform chemical that may be used to produce a wide range of chemicals including 1,4-butanediol, tetrahydrofurane, and γ-butyrolactone. However, industrial fermentation of organic acids is often subject to end-product inhibition, which significantly retards cell growth and limits metabolic activities and final productivity. In this study, we report the development of metabolically engineered Corynebacterium glutamicum for high production of succinate by release of end-product inhibition coupled with an increase of key metabolic flux. It was found that the rates of glucose consumption and succinate production were significantly reduced by extracellular succinate in an engineered strain, S003. To understand the mechanism underlying the inhibition by succinate, comparative transcriptome analysis was performed. Among the downregulated genes, overexpression of the NCgl0275 gene was found to suppress the inhibition of glucose consumption and succinate production, resulting in a 37.7% increase in succinate production up to 55.4g/L in fed-batch fermentation. Further improvement was achieved by increasing the metabolic flux from PEP to OAA. The final engineered strain was able to produce 152.2g/L succinate, the highest production reported to date, with a yield of 1.1g/g glucose under anaerobic condition. These results suggest that the release of end-product inhibition coupled with an increase in key metabolic flux is a promising strategy for enhancing production of succinate. Copyright © 2017. Published by Elsevier Inc.

Solubility and disintegration of new calcium aluminate cement (EndoBinder) containing different radiopacifying agents.

PubMed

Garcia, Lucas da Fonseca Roberti; Chinelatti, Michelle Alexandra; Rossetto, Hebert Luis; Pires-de-Souza, Fernanda de Carvalho Panzeri

2014-02-01

The aim of this study was to evaluate the solubility and disintegration of EndoBinder (EB) containing 3 different radiopacifying agents, bismuth oxide (Bi2O3), zinc oxide (ZnO), or zirconium oxide (ZrO2), in comparison with gray mineral trioxide aggregate (GMTA) and white MTA (WMTA). Ten specimens of each cement were made in a stainless steel matrix (20 × 1.5 mm) according to Specification no. 57 of American National Standards Institute/American Dental Association: EB + Bi2O3, EB + ZrO, EB + ZnO, WMTA, and GMTA. The specimens were weighed on an accurate analytical scale and immersed in 50 mL distilled and deionized water at 37°C for 7 days. Afterwards, specimens were dried and weighed again to determine mass loss (%). Resulting solutions were analyzed in an atomic absorption spectrophotometer for identification and quantification of chemical elements released. All cements presented mean values of solubility and disintegration above the American National Standards Institute/American Dental Association Specification no. 57. EB + Bi2O3 presented the lowest mass loss (5.08%) and WMTA (6.65%) the highest, with no statistically significant difference (P > .05). The release of several chemical elements was observed, mostly metal ions. Only GMTA and EB + Bi2O3 showed the presence of Cr, with significant difference (P < .05). EB + ZnO presented the highest levels of Pb, followed by WMTA (P < .05). For As, the cements presented different release levels, with EB + ZnO showing the highest and GMTA the lowest levels (P < .05). However, the amounts of As and Pb released were lower than the safe limit proposed by ISO 9917-1. Irrespective of the radiopacifying agents used, EndoBinder presented similar behavior to MTA. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Biological denitrification in marine aquaculture systems: A multiple electron donor microcosm study.

PubMed

He, Qiaochong; Zhang, Dongqing; Main, Kevan; Feng, Chuanping; Ergas, Sarina J

2018-05-08

There is a lack of information on denitrification of saline wastewaters, such as those from marine recirculating aquaculture systems (RAS), ion exchange brines and wastewater in areas where sea water is used for toilet flushing. In this study, side-by-side microcosms were used to compare methanol, fish waste (FW), wood chips, elemental sulfur (S 0 ) and a combination of wood chips and sulfur for saline wastewater denitrification. The highest denitrification rate was obtained with methanol (23.4 g N/(m 3 ·d)), followed by FW (4.5 g N/(m 3 ·d)), S 0 (3.5 g N/(m 3 ·d)), eucalyptus mulch (2.6 g N/(m 3 ·d)), and eucalyptus mulch with sulfur (2.2 g N/(m 3 ·d)). Significant differences were observed in denitrification rate for different wood species (pine > oak ≫ eucalyptus) due to differences in readily biodegradable organic carbon released. A pine wood-sulfur heterotrophic-autotrophic denitrification (P-WSHAD) process provided a high denitrification rate (7.2-11.9 g N/(m 3 ·d)), with lower alkalinity consumption and sulfate generation than sulfur alone. Copyright © 2018 Elsevier Ltd. All rights reserved.

Solid lipid nanoparticles as carrier for sunscreens: in vitro release and in vivo skin penetration.

PubMed

Wissing, S A; Müller, R H

2002-06-17

The aim of this study was the comparison of two different formulations (solid lipid nanoparticles (SLN) and conventional o/w emulsion) as carrier systems for the molecular sunscreen oxybenzone. The influence of the carrier on the rate of release was studied in vitro with a membrane-free model. The release rate could be decreased by up to 50% with the SLN formulation. Further in vitro measurements with static Franz diffusion cells were performed. In vivo, penetration of oxybenzone into stratum corneum on the forearm was investigated by the tape stripping method. It was shown that the rate of release is strongly dependent upon the formulation and could be decreased by 30-60% in SLN formulations. In all test models, oxybenzone was released and penetrated into human skin more quickly and to a greater extent from the emulsions. The rate of release also depends upon the total concentration of oxybenzone in the formulation. In vitro-in vivo correlations could be made qualitatively.

Sustained release of methotrexate through liquid-crystalline folate nanoparticles.

PubMed

Misra, Rahul; Mohanty, Sanat

2014-09-01

To make chemotherapy more effective, sustained release of the drug is desirable. By controlling the release rates, constant therapeutic levels can be achieved which can avoid re-administration of drug. This helps to combat tumors more effectively with minimal side effects. The present study reports the control release of methotrexate through liquid-crystalline folate nanoparticles. These nanoparticles are composed of highly ordered folate self-assembly which encapsulate methotrexate molecules. These drug molecules can be released in a controlled manner by disrupting this assembly in the environment of monovalent cations. The ordered structure of folate nanoparticles offers low drug losses of about 4-5%, which is significant in itself. This study reports the size-control method of forming methotrexate encapsulated folate nanoparticles as well as the release of methotrexate through these nanoparticles. It has been demonstrated that methotrexate release rates can be controlled by controlling the size of the nanoparticles, cross-linking cation and cross-linking concentration. The effect of different factors like drug loading, release medium, and pH of the medium on methotrexate release rates was also studied.

Matrix resin effects in composite delamination - Mode I fracture aspects

NASA Technical Reports Server (NTRS)

Hunston, Donald L.; Moulton, Richard J.; Johnston, Norman J.; Bascom, Willard D.

1987-01-01

A number of thermoset, toughened thermoset, and thermoplastic resin matrix systems were characterized for Mode I critical strain energy release rates, and their composites were tested for interlaminar critical strain energy release rates using the double cantilever beam method. A clear correlation is found between the two sets of data. With brittle resins, the interlaminar critical strain energy release rates are somewhat larger than the neat resin values due to a full transfer of the neat resin toughness to the composite and toughening mechanisms associated with crack growth. With tougher matrices, the higher critical strain energy release rates are only partially transferred to the composites, presumably because the fibers restrict the crack-tip deformation zones.

The psychology of perpetrators of 'political' violence in South Africa--a personal experience.

PubMed

Fourie, J A

2000-01-01

My journey embarks with our daughter Lyndi's death at the Heidelberg Massacre in December 1993 and follows the tortuous route of the criminal trial at the end of 1994, through the Truth and Reconciliation Commission (TRC) Hearings in October 1997, to the discovery that there is no formal provision made by the TRC for counselling of Amnesty Seekers. My concern is for those who have received a militarist socialisation and are now being released into a society already burdened with one of the highest 'political' death rates in the world. What is the way forward? Current local models of dealing with trauma for survivors may be helpful in debriefing for those granted amnesty. However, a large-scale effort is necessary to bring about reconciliation and healing in our broken society, some suggestions are made in this regard.

Radioactive release during nuclear accidents in Chernobyl and Fukushima

NASA Astrophysics Data System (ADS)

Nur Ain Sulaiman, Siti; Mohamed, Faizal; Rahim, Ahmad Nabil Ab

2018-01-01

Nuclear accidents that occurred in Chernobyl and Fukushima have initiated many research interests to understand the cause and mechanism of radioactive release within reactor compound and to the environment. Common types of radionuclide release are the fission products from the irradiated fuel rod itself. In case of nuclear accident, the focus of monitoring will be mostly on the release of noble gases, I-131 and Cs-137. As these are the only accidents have been rated within International Nuclear Events Scale (INES) Level 7, the radioactive release to the environment was one of the critical insights to be monitored. It was estimated that the release of radioactive material to the atmosphere due to Fukushima accident was approximately 10% of the Chernobyl accident. By referring to the previous reports using computational code systems to model the release rate, the release activity of I-131 and Cs-137 in Chernobyl was significantly higher compare to Fukushima. The simulation code also showed that Chernobyl had higher release rate of both radionuclides on the day of accident. Other factors affecting the radioactive release for Fukushima and Chernobyl accidents such as the current reactor technology and safety measures are also compared for discussion.

Suicide after release from prison - a population-based cohort study from Sweden

PubMed Central

Haglund, Axel; Tidemalm, Dag; Jokinen, Jussi; Långström, Niklas; Liechtenstein, Paul; Fazel, Seena; Runeson, Bo

2015-01-01

Objective Released prisoners have high suicide rates compared with the general population, but little is known about risk factors and possible causal pathways. We conducted a population-based cohort study to investigate rates and risk factors for suicide in people previously imprisoned. Methods We identified individuals released from prison in Sweden between January 1, 2005 and December 31, 2009 through linkage of national population-based registers. Released prisoners were followed from the day of release until death, emigration, new incarceration, or December 31, 2009. Survival analyses were conducted to compare incidence rates and psychiatric morbidity with non-convicted population controls matched on gender and year of birth. Results We identified 38,995 releases among 26,953 prisoners (7.6% females) during 2005-2009. Overall, 127 suicides occurred, accounting for 14% of all deaths after release (n=920). The mean suicide rate was 204 per 100,000 person years yielding an incidence rate ratio of 18.2 (95% CI 13.9-23.8) compared with general population controls. Previous substance use disorder (Hazard Ratio [HR]=2.1, 1.4-3.2), suicide attempt (HR=2.5, 1.7-3.7), and being born in Sweden vs. abroad (HR=2.1, 1.2-3.6) were independent risk factors for suicide after release. Conclusions Released prisoners are at high suicide risk and with a slightly different pattern of psychiatric risk factors for suicide compared with the general population. Results suggest appropriate allocation of resources to facilitate transition to life outside prison and increased attention to prisoners with both a previous suicide attempt and substance use disorder. PMID:25373114

[Characteristics of ammonia volatilization and nitrous oxide emission from a paddy soil under continuous application of different slow/controlled release urea.

PubMed

Sun, Xiang Xin; Li, Dong Po; Wu, Zhi Jie; Cui, Ya Lan; Han, Mei; Li, Yong Hua; Yang, De Fu; Cui, Yong Kun

2016-06-01

The characteristics of ammonia volatilization and nitrous oxide emission from a paddy soil were examined under 9-year application of different slow/controlled release urea with the common large granule urea (U) as the control. The results showed that compared with the control, all slow/controlled release urea treatments, except 25.8% increase of ammonia volatilization under 1% 3,4-dimethylpyrazole phosphate (DMPP)+U, could decrease the ammonia volatilization. Polymer coated urea (PCU) dominated the highest reduction of 73.4% compared to U, followed by sulfur coated urea (SCU) (72.2%), 0.5% N-(N-butyl) thiophosphoric triamide (NBPT)+1% DMPP+U (71.9%), 1% hydroquinone (HQ)+3% dicyandiamide (DCD)+U (46.9%), 0.5% NBPT+U (43.2%), 1% HQ +U (40.2%), 3% DCD+U (25.5%), and the ammonia volatilization under different slow/controlled release urea treatments were statistically lower than that of U (P<0.05). 1% DMPP+U caused the lowest emission of N 2 O under different slow/controlled release urea treatments. The slow/controlled release urea also had a significant potential of N 2 O emission reduction: 1% DMPP+U showed the highest reduction of 74.9% compared to U, followed by PCU (62.1%), 1% HQ+3% DCD+U (54.7%), 0.5% NBPT+1% DMPP+U (42.2%), 3% DCD+U (35.9%), 1% HQ +U (28.9%), 0.5% NBPT+U (17.7%), SCU (14.5%), and N 2 O emissions under different slow/controlled release urea treatments were statistically lower than that of U (P<0.05). The comprehensive analysis showed that 0.5% NBPT+1% DMPP+U, SCU and PCU had similar effects on decreasing the ammonia volatilization and N 2 O emission and were remarkably better than the other treatments. The slow release urea with the combination of urease and nitrification inhibitors should be the first choice for reducing N loss and environmental pollution in paddy field, in view of the higher costs of coated urea fertilizers.

Preparation and release study of Triclosan in polyethylene/Triclosan anti-bacterial blend.

PubMed

Kamalipour, Jamshid; Masoomi, Mahmood; Khonakdar, Hossein Ali; Razavi, Seyed Mohammad Reza

2016-09-01

In this study, medium density polyethylene (MDPE) incorporated with Triclosan antibacterial substance has been prepared and Triclosan release rate was investigated. The crystallinity level and matrix polarity, as two significant parameters in antibacterial release control, were studied. Triclosan, a well-established widespread antibacterial agent, was incorporated into medium density polyethylene (MDPE) and Maleic anhydride grafted polyethylene (PE-g-MA) was used to change the polarity of the MDPE matrix. A masterbatch of 10wt% Triclosan incorporated with the MDPE and various PE-g-MA concentrations were prepared using an internal mixer. Then the masterbatch was diluted in the MDPE matrix to produce compounds with 0.1, 0.5, and1wt% Triclosan via twin screw extruder. The compounds were molded by compression molding method and then were cooled in three different cooling rate methods: isothermal cooling (I), quenching (Q),and moderate 5-10°C/min cooling rate (M). Cooling rate effects on crystallinity level were investigated applying sample density measurement. UV-vis absorption spectroscopy was used to probe the release of Triclosan. Antibacterial properties of the compounds against Escherichia coli, Klebsiella pneumoniae, and Staphylococcus aureus were measured. The results showed that by addition of PE-g-MA, Triclosan release rate was increased. It was confirmed that the sample crystallinity was decreased by the cooling rate enhancement. The results also showed that quenched samples indicated higher release of Triclosan. Cooling rate reduction and raising the polarity increased the release of Triclosan and improved the antibacterial properties of the compounds. Copyright © 2016 Elsevier B.V. All rights reserved.

The release rate of environmental DNA from juvenile and adult fish.

PubMed

Maruyama, Atsushi; Nakamura, Keisuke; Yamanaka, Hiroki; Kondoh, Michio; Minamoto, Toshifumi

2014-01-01

The environmental DNA (eDNA) technique is expected to become a powerful, non-invasive tool for estimating the distribution and biomass of organisms. This technique was recently shown to be applicable to aquatic vertebrates by collecting extraorganismal DNA floating in the water or absorbed onto suspended particles. However, basic information on eDNA release rate is lacking, despite it being essential for practical applications. In this series of experiments with bluegill sunfish (Lepomis macrochirus), we examined the effect of fish developmental stage on eDNA release rate. eDNA concentration reached equilibrium 3 days after the individual fish were introduced into the separate containers, enabling calculation of the eDNA release rate (copies h-1) from individual fish on the assumption that the number of eDNA released from the fish per unit time equals total degradation in the container (copies h-1). The eDNA release rate was 3-4 times higher in the adult (body weight: 30-75 g) than in the juvenile group (0.5-2.0 g). Such positive relationship between fish size and eDNA release rate support the possibility of biomass rather than density estimation using eDNA techniques. However, the eDNA release rate per fish body weight (copies h-1 g-1) was slightly higher in the juvenile than the adult group, which is likely because of the ontogenetic reduction in metabolic activity. Therefore, quantitative eDNA data should be carefully interpreted to avoid overestimating biomass when the population is dominated by juveniles, because the age structure of the focal population is often variable and unseen in the field. eDNA degradation rates (copies l-1 h-1), calculated by curve fitting of time-dependent changes in eDNA concentrations after fish removal, were 5.1-15.9% per hour (half-life: 6.3 h). This suggests that quantitative eDNA data should be corrected using a degradation curve attained in the target field.

Influence of factors on release of antimicrobials from antimicrobial packaging materials.

PubMed

Wu, Yu-Mei; Wang, Zhi-Wei; Hu, Chang-Ying; Nerín, Cristina

2018-05-03

Antimicrobial packaging materials (films or coatings) (APMs) have aroused great interest among the scientists or the experts specialized in material science, food science, packaging engineering, biology and chemistry. APMs have been used to package the food, such as dairy products, poultry, meat (e.g., beef), salmon muscle, pastry dough, fresh pasta, bakery products, fruits, vegetables and beverages. Some materials have been already commercialized. The ability of APMs to extend the shelf-life of the food depends on the release rate of the antimicrobials (AMs) from the materials to the food. The optimum rate is defined as target release rate (TRR). To achieve TRR, the influencing factors of the release rate should be considered. Herein we reviewed for the first time these factors and their influence on the release. These factors mainly include the AMs, food (or food simulant), packaging materials, the interactions among them, the temperature and environmental relative humidity (RH).

Effect of calcium on fatty acid bioaccessibility during in vitro digestion of Cheddar-type cheeses prepared with different milk fat fractions.

PubMed

Ayala-Bribiesca, Erik; Turgeon, Sylvie L; Britten, Michel

2017-04-01

Calcium plays an important role in intestinal lipid digestion by increasing the lipolysis rate, but also limits fatty acid bioaccessibility by producing insoluble Ca soaps with long-chain fatty acids at intestinal pH conditions. The aim of this study was to better understand the effect of Ca on the bioaccessibility of milk fat from Cheddar-type cheeses. Three anhydrous milk fats (AMF) with different fatty acid profiles (olein, stearin, or control AMF) were used to prepare Cheddar-type cheeses, which were then enriched or not with Ca using CaCl 2 during the salting step. The cheeses were digested in vitro, and their disintegration and lipolysis rates were monitored during the process. At the end of digestion, lipids were extracted under neutral and acidic pH conditions to compare free fatty acids under intestinal conditions in relation to total fatty acids released during the digestion process. The cheeses prepared with the stearin (the AMF with the highest ratio of long-chain fatty acids) were more resistant to disintegration than the other cheeses, owing to the high melting temperature of that AMF. The Ca-enriched cheeses had faster lipolysis rates than the regular Ca cheeses. Chromatographic analysis of the digestion products showed that Ca interacted with long-chain fatty acids, producing Ca soaps, whereas no interaction with shorter fatty acids was detected. Although higher Ca levels resulted in faster lipolysis rates, driven by the depletion of reaction products as Ca soaps, such insoluble compounds are expected to reduce the bioavailability of fatty acids by hindering their absorption. These effects on lipid digestion and absorption are of interest for the design of food matrices for the controlled release of fat-soluble nutrients or bioactive molecules. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Variation among states in prescribing of opioid pain relievers and benzodiazepines--United States, 2012.

PubMed

Paulozzi, Leonard J; Mack, Karin A; Hockenberry, Jason M

2014-12-01

Overprescribing of opioid pain relievers (OPR) can result in multiple adverse health outcomes, including fatal overdoses. Interstate variation in rates of prescribing OPR and other prescription drugs prone to abuse, such as benzodiazepines, might indicate areas where prescribing patterns need further evaluation. CDC analyzed a commercial database (IMS Health) to assess the potential for improved prescribing of OPR and other drugs. CDC calculated state rates and measures of variation for OPR, long-acting/extended-release (LA/ER) OPR, high-dose OPR, and benzodiazepines. In 2012, prescribers wrote 82.5 OPR and 37.6 benzodiazepine prescriptions per 100 persons in the United States. State rates varied 2.7-fold for OPR and 3.7-fold for benzodiazepines. For both OPR and benzodiazepines, rates were higher in the South census region, and three Southern states were two or more standard deviations above the mean. Rates for LA/ER and high-dose OPR were highest in the Northeast. Rates varied 22-fold for one type of OPR, oxymorphone. Factors accounting for the regional variation are unknown. Such wide variations are unlikely to be attributable to underlying differences in the health status of the population. High rates indicate the need to identify prescribing practices that might not appropriately balance pain relief and patient safety. State policy makers might reduce the harms associated with the abuse of prescription drugs by implementing changes that will make the prescribing of these drugs more cautious and more consistent with clinical recommendations. Published by Elsevier Ltd.

Microencapsulation of citronella oil for mosquito-repellent application: formulation and in vitro permeation studies.

PubMed

Solomon, B; Sahle, F F; Gebre-Mariam, T; Asres, K; Neubert, R H H

2012-01-01

Citronella oil (CO) has been reported to possess a mosquito-repellent action. However, its application in topical preparations is limited due to its rapid volatility. The objective of this study was therefore to reduce the rate of evaporation of the oil via microencapsulation. Microcapsules (MCs) were prepared using gelatin simple coacervation method and sodium sulfate (20%) as a coacervating agent. The MCs were hardened with a cross-linking agent, formaldehyde (37%). The effects of three variables, stirring rate, oil loading and the amount of cross-linking agent, on encapsulation efficiency (EE, %) were studied. Response surface methodology was employed to optimize the EE (%), and a polynomial regression model equation was generated. The effect of the amount of cross-linker was insignificant on EE (%). The response surface plot constructed for the polynomial equation provided an optimum area. The MCs under the optimized conditions provided EE of 60%. The optimized MCs were observed to have a sustained in vitro release profile (70% of the content was released at the 10th hour of the study) with minimum initial burst effect. Topical formulations of the microencapsulated oil and non-microencapsulated oil were prepared with different bases, white petrolatum, wool wax alcohol, hydrophilic ointment (USP) and PEG ointment (USP). In vitro membrane permeation of CO from the ointments was evaluated in Franz diffusion cells using cellulose acetate membrane at 32 °C, with the receptor compartment containing a water-ethanol solution (50:50). The receptor phase samples were analyzed with GC/MS, using citronellal as a reference standard. The results showed that microencapsulation decreased membrane permeation of the CO by at least 50%. The amount of CO permeated was dependent on the type of ointment base used; PEG base exhibited the highest degree of release. Therefore, microencapsulation reduces membrane permeation of CO while maintaining a constant supply of the oil. Copyright © 2011 Elsevier B.V. All rights reserved.

Topical nanoparticulate formulation of drugs for ocular keratitis

NASA Astrophysics Data System (ADS)

Yang, Xiaoyan

The primary objective of this project is to develop drug-loaded polymeric nanoparticles suspended in a biocompatible gel for topical delivery of therapeutic agents commonly employed in the treatment of ocular viral/bacterial keratitis. PART 1: Poly(D,L-lactic-co-glycolic acid) (PLGA) nanoparticles (NP) of dipeptide monoester prodrugs of ganciclovir (GCV) including L-Val-L-Val-GCV (LLGCV), L-Val-D-Val-GCV (LDGCV), D-Val-L-Val-GCV (DLGCV) were formulated and dispersed in thermosensitive PLGA-PEG-PLGA polymer gel for the treatment of herpes simplex virus type 1 (HSV-1) induced viral corneal keratitis. NP containing prodrugs of GCV were prepared by a double-emulsion solvent evaporation technique using various PLGA polymers with different drug/polymer ratios. Cytotoxicity studies suggested that all NP formulations are non-toxic. In vitro release of prodrugs from NP showed a biphasic release pattern with an initial burst phase followed by a sustained phase. Such burst effect was completely eliminated when NP were suspended in thermosensitive gels with near zero-order release kinetics. Prodrugs-loaded PLGA NP dispersed in thermosensitive gels can thus serve as a promising drug delivery system for the treatment of anterior eye diseases. Maximum uptake (around 60%) was noted at 3 h for NP. Cellular uptake and intracellular accumulation of prodrugs are significantly different among three stereoisomeric dipeptide prodrugs. The microscopic images show that NP are avidly internalized by HCEC cells and distributed throughout the cytoplasm instead of being localized on the cell surface. Following cellular uptake, prodrugs released from NP gradually bioreversed into parent drug GCV. LLGCV showed the highest degradation rate, followed by LDGCV and DLGCV. LLGCV, LDGCV and DLGCV released from NP exhibited superior uptake and bioreversion in corneal cells. PART 2: PLGA NP of hydrocortisone butyrate (HB) suspended in thermosensitive PLGA-PEG-PLGA gel were developed for the treatment of bacterial corneal keratitis. Experimental designs were employed in order to investigate specific effects of independent variables during preparation of HB-loaded PLGA NP and corresponding responses in optimizing the formulation. NP containing HB were prepared by an oil-in-water (O/W) emulsion evaporation technique with different surfactants including polyvinyl alcohol (PVA), pluronic F-108 and chitosan. NP were characterized with respect to particle size, entrapment efficiency, polydispersity, drug loading, surface morphology, zeta potential and crystallinity. In vitro release of HB from NP showed a biphasic release pattern with an initial burst phase followed by a sustained phase. Such burst effect was completely eliminated when NP were suspended in thermosensitive gels and zero-order release kinetics was observed. Percentage of uptake in HCEC after 4 h was 59.09+/-6.21% for PVA-emulsified NP relative to 55.74+/-6.26% for pluronic-emulsified NP, and 62.54+/-3.30% for chitosan-emulsified NP, respectively. In HCEC cell line, chitosan-emulsified NP with chitosan showed highest cellular uptake efficiency over PVA- and pluronic-emulsified NP. However, NP with chitosan indicated significant cytotoxicity under 200 and 500 ?g/mL after 48 h, while NP with PVA and pluronic showed no significant cytotoxicity. PLGA NP dispersed in thermosensitive gels can be considered as a promising drug delivery system for the treatment of anterior eye diseases.

Radon Release and Its Simulated Effect on Radiation Doses.

PubMed

Orabi, Momen

2017-03-01

One of the main factors that affect the uncertainty in calculating the gamma-radiation absorbed dose rate inside a room is the variation in the degree of secular equilibrium of the considered radioactive series. A component of this factor, considered in this paper, is the release of radon (Rn) from building materials to the living space of the room. This release takes place through different steps. These steps are represented and mathematically formulated. The diffusion of radon inside the material is described by Fick's second law. Some of the factors affecting the radon release rate (e.g. covering walls, moisture, structure of the building materials, etc.) are discussed. This scheme is used to study the impact of radon release on the gamma-radiation absorbed dose rate inside a room. The investigation is carried out by exploiting the MCNP simulation software. Different building materials are considered with different radon release rates. Special care is given to Rn due to its relatively higher half-life and higher indoor concentration than the other radon isotopes. The results of the presented model show that the radon release is of a significant impact in some building materials.

Subsidence in tropical peatlands: Estimating CO2 fluxes from peatlands in Southeast Asia

NASA Astrophysics Data System (ADS)

Hoyt, A.; Harvey, C. F.; Seppalainen, S. S.; Chaussard, E.

2017-12-01

Tropical peatlands of Southeast Asia are an important global carbon stock. However, they are being rapidly deforested and drained. Peatland drainage facilitates peat decomposition, releases sequestered peat carbon to the atmosphere as CO2, and leads to subsidence of the peat surface. As a result, subsidence measurements can be used to monitor peatland carbon loss over time. Until now, subsidence measurements have been primarily limited to ground-based point measurements using subsidence poles. Here we demonstrate a powerful method to measure peatland subsidence rates across much larger areas than ever before. Using remotely sensed InSAR data, we map subsidence rates across thousands of square kilometers in Southeast Asia and validate our results against ground-based subsidence measurements. The method allows us to monitor subsidence in remote locations, providing unprecedented spatial information, and the first comprehensive survey of land uses such as degraded peatlands, burnt and open areas, shrub lands, and smallholder farmlands. Strong spatial patterns emerged, with the highest subsidence rates occurring at the centers of peat domes, where the peat is thickest and drainage depths are likely to be largest. Peatland subsidence rates were also strongly dependent on current and historical land use, with typical subsidence rates ranging from 2-4 cm/yr. Finally, we scaled up our results to calculate total annual emissions from peat decomposition in degraded peatlands.

Impact of heat release on strain rate field in turbulent premixed Bunsen flames

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coriton, Bruno Rene Leon; Frank, Jonathan H.

2016-08-10

The effects of combustion on the strain rate field are investigated in turbulent premixed CH 4/air Bunsen flames using simultaneous tomographic PIV and OH LIF measurements. Tomographic PIV provides three-dimensional velocity measurements, from which the complete strain rate tensor is determined. The OH LIF measurements are used to determine the position of the flame surface and the flame-normal orientation within the imaging plane. This combination of diagnostic techniques enables quantification of divergence as well as flame-normal and tangential strain rates, which are otherwise biased using only planar measurements. Measurements are compared in three lean-to-stoichiometric flames that have different amounts ofmore » heat release and Damköhler numbers greater than unity. The effects of heat release on the principal strain rates and their alignment relative to the local flame normal are analyzed. The extensive strain rate preferentially aligns with the flame normal in the reaction zone, which has been indicated by previous studies. The strength of this alignment increases with increasing heat release and, as a result, the flame-normal strain rate becomes highly extensive. These effects are associated with the gas expansion normal to the flame surface, which is largest for the stoichiometric flame. In the preheat zone, the compressive strain rate has a tendency to align with the flame normal. Away from the flame front, the flame – strain rate alignment is arbitrary in both the reactants and products. The flame-tangential strain rate is on average positive across the flame front, and therefore the turbulent strain rate field contributes to the enhancement of scalar gradients as in passive scalar turbulence. As a result, increases in heat release result in larger positive values of the divergence as well as flame-normal and tangential strain rates, the tangential strain rate has a weaker dependence on heat release than the flame-normal strain rate and the divergence.« less

Connecting nitrogen deposition and ecosystem services

EPA Science Inventory

There are tremendous human health and well-being consequences of nitrogen release to the atmosphere, land and water. The effects on human health are related to the fundamental ecosystem services providing clean air and water for human consumption. Among the highest available da...

A comparison of video review and feedback device measurement of chest compressions quality during pediatric cardiopulmonary resuscitation.

PubMed

Hsieh, Ting-Chang; Wolfe, Heather; Sutton, Robert; Myers, Sage; Nadkarni, Vinay; Donoghue, Aaron

2015-08-01

To describe chest compression (CC) rate, depth, and leaning during pediatric cardiopulmonary resuscitation (CPR) as measured by two simultaneous methods, and to assess the accuracy and reliability of video review in measuring CC quality. Resuscitations in a pediatric emergency department are videorecorded for quality improvement. Patients aged 8-18 years receiving CPR under videorecording were eligible for inclusion. CPR was recorded by a pressure/accelerometer feedback device and tabulated in 30-s epochs of uninterrupted CC. Investigators reviewed videorecorded CPR and measured rate, depth, and release by observation. Raters categorized epochs as 'meeting criteria' if 80% of CCs in an epoch were done with appropriate depth (>45 mm) and/or release (<2.5 kg leaning). Comparison between device measurement and video was made by Spearman's ρ for rate and by κ statistic for depth and release. Interrater reliability for depth and release was measured by κ statistic. Five patients underwent videorecorded CPR using the feedback device. 97 30-s epochs of CCs were analyzed. CCs met criteria for rate in 74/97 (76%) of epochs; depth in 38/97 (39%); release in 82/97 (84%). Agreement between video and feedback device for rate was good (ρ = 0.77); agreement was poor for depth and release (κ 0.04-0.41). Interrater reliability for depth and release measured by video was poor (κ 0.04-0.49). Video review measured CC rate accurately; depth and release were not reliably or accurately assessed by video. Future research should focus on the optimal combination of methods for measuring CPR quality. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Polyamidoamine (PAMAM) dendrimers as potential release modulators and oral bioavailability enhancers of vardenafil hydrochloride.

PubMed

Tawfik, Mai Ahmed; Tadros, Mina Ibrahim; Mohamed, Magdy Ibrahim

2018-05-21

Vardenafil hydrochloride (VAR) is an erectile dysfunction treating drug. VAR has a short elimination half-life (4-5 h) and suffers low oral bioavailability (15%). This work aimed to explore the dual potential of VAR-dendrimer complexes as drug release modulators and oral bioavailability enhancers. VAR-dendrimer complexes were prepared by solvent evaporation technique using four dendrimer generations (G4.5, G5, G5.5 and G6) at three concentrations (190 nM, 380 nM and 950 nM). The systems were evaluated for intermolecular interactions, particle size, zeta potential, drug entrapment efficiency percentages (EE%) and drug released percentages after 2 h (Q 2h ) and 24 h (Q 24h ). The results were statistically analyzed, and the system showing the highest desirability was selected for further pharmacokinetic studies in rabbits, in comparison to Levitra ® tablets. The highest desirability (0.82) was achieved with D10 system comprising VAR (10 mg) and G6 (190 nM). It possessed small particle size (113.85 nm), low PDI (0.19), positive zeta potential (+21.53), high EE% (75.24%), promising Q 2 h (41.45%) and Q 24 h (74.05%). Compared to Levitra ® tablets, the significantly (p < 0.01) delayed T max , prolonged MRT (0-∞) and higher relative bioavailability (3.7-fold) could clarify the dual potential of D10 as a sustained release system capable of enhancing VAR oral bioavailability.

Effect of Sarcoplasmic Reticulum (SR) Calcium Content on SR Calcium Release Elicited by Small Voltage-Clamp Depolarizations in Frog Cut Skeletal Muscle Fibers Equilibrated with 20 mM EGTA

PubMed Central

Pape, Paul C.; Carrier, Nicole

1998-01-01

Cut muscle fibers from Rana temporaria (sarcomere length, 3.5–3.9 μm; 14–16°C) were mounted in a double Vaseline-gap chamber and equilibrated with an external solution that contained tetraethyl ammonium– gluconate and an internal solution that contained Cs as the principal cation, 20 mM EGTA, and 0 Ca. Fibers were stimulated with a voltage-clamp pulse protocol that consisted of pulses to −70, −65, −60, −45, and −20 mV, each separated by 400-ms periods at −90 mV. The change in total Ca that entered into the myoplasm (Δ[CaT]) and the Ca content of the SR ([CaSR]) were estimated with the EGTA/phenol red method (Pape, P.C., D.-S. Jong, and W.K. Chandler. 1995. J. Gen. Physiol. 106:259–336). Fibers were stimulated with the pulse protocol, usually every 5 min, so that the resting value of [CaSR] decreased from its initial value of 1,700–2,300 μM to values near or below 100 μM after 18–30 stimulations. Three main findings for the voltage pulses to −70, −65, and −60 mV are: (a) the depletion-corrected rate of Ca release (release permeability) showed little change when [CaSR] decreased from its highest level (>1,700 μM) to ∼1,000 μM; (b) as [CaSR] decreased below 1,000 μM, the release permeability increased to a maximum level when [CaSR] was near 300 μM that was on average about sevenfold larger than the values observed for [CaSR] > 1,000 μM; and (c) as [CaSR] decreased from ∼300 μM to <100 μM, the release permeability decreased, reaching half its maximum value when [CaSR] was ∼110 μM on average. It was concluded that finding b was likely due to a decrease in Ca inactivation, while finding c was likely due to a decrease in Ca-induced Ca release. PMID:9689025

Effect of Irrigation Time of Antiseptic Solutions on Bone Cell Viability and Growth Factor Release.

PubMed

Sawada, Kosaku; Nakahara, Ken; Haga-Tsujimura, Maiko; Fujioka-Kobayashi, Masako; Iizuka, Tateyuki; Miron, Richard J

2018-03-01

Antiseptic solutions are commonly utilized to treat local infection in the oral and maxillofacial region. However, surrounding vital bone is also exposed to antiseptic agents during irrigation and may have a potential negative impact on bone survival. The aim of the present study was therefore to investigate the effect of rinsing time with various antiseptic solutions on bone cell viability, as well as their subsequent release of growth factors important for bone regeneration. The bone samples collected from porcine mandible were rinsed in the following commonly utilized antiseptic solutions; povidone-iodine (0.5%), chlorhexidine digluconate (CHX, 0.2%), hydrogen peroxide (1%), and sodium hypochlorite (0.25%) for 1, 5, 10, 20, 30, or 60 minutes and assessed for cell viability and release of growth factors including vascular endothelial growth factor, transforming growth factor beta 1, bone morphogenetic protein 2, receptor activator of nuclear factor kappa-B ligand, and interleukin-1 beta by enzyme-linked immunosorbent assay. It was found in all the tested groups that the long exposure of any of the tested antiseptic solutions drastically promoted higher cell death. Sodium hypochlorite demonstrated the significantly highest cell death and at all time points. Interestingly, bone cell viability was highest in the CHX group post short-term rinsing of 1, 5, or 10 minutes when compared with the other 4 tested groups. A similar trend was also observed in subsequent growth factor release. The present study demonstrated that of the 4 tested antiseptic solutions, short-term CHX rinsing (ideally within 1 minute) favored bone cell viability and growth factor release. Clinical protocols should be adapted accordingly.

Development of a novel osmotically driven drug delivery system for weakly basic drugs.

PubMed

Guthmann, C; Lipp, R; Wagner, T; Kranz, H

2008-06-01

The drug substance SAG/ZK has a short biological half-life and because of its weakly basic nature a strong pH-dependent solubility was observed. The aim of this study was to develop a controlled release (cr) multiple unit pellet formulation for SAG/ZK with pH-independent drug release. Pellets with a drug load of 60% were prepared by extrusion/spheronization followed by cr-film coating with an extended release polyvinyl acetate/polyvinyl pyrrolidone dispersion (Kollidon SR 30 D). To overcome the problem of pH-dependent drug release the pellets were then coated with a second layer of an enteric methacrylic acid and ethyl acrylate copolymer (Kollicoat MAE 30 DP). To increase the drug release rates from the double layered cr-pellets different osmotically active ionic (sodium and potassium chloride) and nonionic (sucrose) additives were incorporated into the pellet core. Drug release studies were performed in media of different osmotic pressure to clarify the main release mechanism. Extended release coated pellets of SAG/ZK demonstrated pH-dependent drug release. Applying a second enteric coat on top of the extended release film coat failed in order to achieve pH-independent drug release. Already low enteric polymer levels on top of the extended release coated pellets decreased drug release rates at pH 1 drastically, thus resulting in a reversal of the pH-dependency (faster release at pH 6.8 than in 0.1N HCl). The addition of osmotically active ingredients (sodium and potassium chloride, and sucrose) increased the imbibing of aqueous fluids into the pellet cores thus providing a saturated drug solution inside the beads and increasing drug concentration gradients. In addition, for these pellets increased formation of pores and cracks in the polymer coating was observed. Hence drug release rates from double layered beads increased significantly. Therefore, pH-independent osmotically driven SAG/ZK release was achieved from pellets containing osmotically active ingredients and coated with an extended and enteric polymer. In contrast, with increasing osmotic pressure of the dissolution medium the in vitro drug release rates decreased significantly.

Enhanced desorption of persistent organic pollutants from microplastics under simulated physiological conditions.

PubMed

Bakir, Adil; Rowland, Steven J; Thompson, Richard C

2014-02-01

Microplastics have the potential to uptake and release persistent organic pollutants (POPs); however, subsequent transfer to marine organisms is poorly understood. Some models estimating transfer of sorbed contaminants to organisms neglect the role of gut surfactants under differing physiological conditions in the gut (varying pH and temperature), examined here. We investigated the potential for polyvinylchloride (PVC) and polyethylene (PE) to sorb and desorb (14)C-DDT, (14)C-phenanthrene (Phe), (14)C-perfluorooctanoic acid (PFOA) and (14)C-di-2-ethylhexyl phthalate (DEHP). Desorption rates of POPs were quantified in seawater and under simulated gut conditions. Influence of pH and temperature was examined in order to represent cold and warm blooded organisms. Desorption rates were faster with gut surfactant, with a further substantial increase under conditions simulating warm blooded organisms. Desorption under gut conditions could be up to 30 times greater than in seawater alone. Of the POP/plastic combinations examined Phe with PE gave the highest potential for transport to organisms. Copyright © 2013 Elsevier Ltd. All rights reserved.

Computational Studies of Drug Release, Transport and Absorption in the Human Intestines

NASA Astrophysics Data System (ADS)

Behafarid, Farhad; Brasseur, J. G.; Vijayakumar, G.; Jayaraman, B.; Wang, Y.

2016-11-01

Following disintegration of a drug tablet, a cloud of particles 10-200 μm in diameter enters the small intestine where drug molecules are absorbed into the blood. Drug release rate depends on particle size, solubility and hydrodynamic enhancements driven by gut motility. To quantify the interrelationships among dissolution, transport and wall permeability, we apply lattice Boltzmann method to simulate the drug concentration field in the 3D gut released from polydisperse distributions of drug particles in the "fasting" vs. "fed" motility states. Generalized boundary conditions allow for both solubility and gut wall permeability to be systematically varied. We apply a local 'quasi-steady state' approximation for drug dissolution using a mathematical model generalized for hydrodynamic enhancements and heterogeneity in drug release rate. We observe fundamental differences resulting from the interplay among release, transport and absorption in relationship to particle size distribution, luminal volume, motility, solubility and permeability. For example, whereas smaller volume encourages higher bulk concentrations and reduced release rate, it also encourages higher absorption rate, making it difficult to generalize predictions. Supported by FDA.

Banks Lake Fishery Evaluation Project Annual Report : Fiscal Year 2008 (March 1, 2008 to February 1, 2009).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Polacek, Matt

2009-07-15

The Washington Department of Fish and Wildlife implemented the Banks Lake Fishery Evaluation Project (BLFEP) in September 2001 with funds from the Bonneville Power Administration, and continued project tasks in 2008. The objective was to evaluate factors that could limit kokanee in Banks Lake, including water quality, prey availability, harvest, and acute predation during hatchery releases. Water quality parameters were collected twice monthly from March through November. Banks Lake water temperatures began to increase in May and stratification was apparent by July. By late August, the thermocline had dropped to 15 meters deep, with temperatures of 21-23 C in themore » epilimnion and 16-19 C in the hypolimnion. Dissolved oxygen levels were generally above 8 mg/L until August when they dropped near or below 5 mg/L deeper than 20-meters. Secchi depths ranged from 3.2 to 6.2 meters and varied spatially and temporally. Daphnia and copepod densities were the highest in May and June, reaching densities of 26 copepods/liter and 9 Daphnia/liter. Fish surveys were conducted in July and October 2008 using boat electrofishing, gill netting, and hydroacoustic surveys. Lake whitefish (71%) and yellow perch (16%) dominated the limnetic fish assemblage in the summer, while lake whitefish (46%) and walleye (22%) were the most abundant in gill net catch during the fall survey. Piscivore diets switched from crayfish prior to the release of rainbow trout to crayfish and rainbow trout following the release. The highest angling pressure occurred in May, when anglers were primarily targeting walleye and smallmouth bass. Boat anglers utilized Steamboat State Park more frequently than any other boat ramp on Banks Lake. Shore anglers used the rock jetty at Coulee City Park 45% of the time, with highest use occurring from November through April. Ice fishing occurred in January and February at the south end of the lake. An estimated total of 4,397 smallmouth bass, 11,106 walleye, 371 rainbow trout, and 509 yellow perch were harvested from Banks Lake in 2008. No kokanee were reported in the creel; however, local reports indicated that anglers were targeting and catching kokanee. The economic benefit of the Banks Lake fishery was estimated at $2,288,005 during 2008. Abundance estimates from the hydroacoustic survey in July were 514,435 lake whitefish and 10,662 kokanee, with an overall abundance estimate of 626,061 limnetic fish greater than 100 mm. When comparing spring fry, fall fingerling and yearling net pen release strategies of kokanee, 95% were of hatchery origin, with the highest recaptures coming from the fall fingerling release group.« less

Development of near zero-order release dosage forms using three-dimensional printing (3-DP) technology.

PubMed

Wang, Chen-Chao; Tejwani Motwani, Monica R; Roach, Willie J; Kay, Jennifer L; Yoo, Jaedeok; Surprenant, Henry L; Monkhouse, Donald C; Pryor, Timothy J

2006-03-01

Three near zero-order controlled-release pseudoephedrine hydrochloride (PEH) formulations demonstrating proportional release rates were developed using 3-Dimensional Printing (3-DP) technology. Mixtures of Kollidon SR and hydroxypropylmethyl cellulose (HPMC) were used as drug carriers. The release rates were adjusted by varying the Kollidon SR-HPMC ratio while keeping fabrication parameters constant. The dosage forms were composed of an immediate release core and a release rate regulating shell, fabricated with an aqueous PEH and an ethanolic triethyl citrate (TEC) binder, respectively. The dosage form design called for the drug to be released via diffusional pathways formed by HPMC in the shell matrix. The release rate was shown to increase correspondingly with the fraction of HPMC contained in the polymer blend. The designed formulations resulted in dosage forms that were insensitive to changes in pH of the dissolution medium, paddle stirring rate, and the presence/absence of a sinker. The near zero-order release properties were unchanged regardless of the dissolution test being performed on either single cubes or on a group of eight cubes encased within a gelatin capsule shell. The chemical and dissolution properties of the three formulations remained unchanged following 1 month's exposure to 25 degrees C/60% RH or 40 degrees C/75% RH environment under open container condition. The in vivo performance of the three formulations was evaluated using a single-dose, randomized, open-label, four-way crossover clinical study composed of 10 fasted healthy volunteers. The pharmacokinetic parameters were analyzed using a noncompartmental model. Qualitative rank order linear correlations between in vivo absorption profiles and in vitro dissolution parameters (with slope and intercept close to unity and origin, respectively) were obtained for all three formulations, indicating good support for a Level A in vivo/in vitro correlation.

Use of proteins to minimize the physical aging of EUDRAGIT sustained release films.

PubMed

Kucera, Shawn A; McGinity, James W; Zheng, Weijia; Shah, Navnit H; Malick, A Waseem; Infeld, Martin H

2007-07-01

The objective of this study was to investigate the influence of two proteins, albumin and type B gelatin, on the physical aging of EUDRAGIT RS 30 D and RL 30 D coated theophylline pellets. The physicomechanical properties of sprayed films, thermal properties of cast films, influence of proteins on the zeta potential and particle size of the dispersion, and the release of proteins from cast films under simulated dissolution conditions were investigated. The release rate of theophylline decreased significantly over time from pellets coated with an acrylic dispersion containing 10% albumin when there was no acidification of the acrylic dispersion; however, when pellets were coated with an acidified EUDRAGIT/albumin dispersion, the theophylline release rate was stable for dosage forms stored in the absence of humidity. The drug release rate was faster for pellets coated with acrylic dispersions containing 10% gelatin compared to the albumin-containing formulations. When sprayed films were stored at 40 degrees C/75% RH, the water vapor permeability decreased significantly for both EUDRAGIT films and those containing EUDRAGIT and albumin; however, there was no significant change in this parameter when 10% gelatin was present. Albumin was released from the acrylic films when the pH of the dissolution media was below the isoelectric point of the protein while no quantitative release of gelatin was observed in pH 1.2 or 7.4 media. The effect of gelatin to prevent the decrease in drug release rate was due to stabilization in water vapor permeability of the film. Acidification of the polymeric dispersion resulted in electrostatic repulsive forces between albumin and the acrylic polymer, which stabilized the drug release rate when the dosage forms were stored in aluminum induction sealed containers at both 40 degrees C/75% RH and 25 degrees C/60% RH.

Role of glycogen availability in sarcoplasmic reticulum Ca2+ kinetics in human skeletal muscle

PubMed Central

Ørtenblad, Niels; Nielsen, Joachim; Saltin, Bengt; Holmberg, Hans-Christer

2011-01-01

Little is known about the precise mechanism that relates skeletal muscle glycogen to muscle fatigue. The aim of the present study was to examine the effect of glycogen on sarcoplasmic reticulum (SR) function in the arm and leg muscles of elite cross-country skiers (n= 10, 72 ± 2 ml kg−1 min−1) before, immediately after, and 4 h and 22 h after a fatiguing 1 h ski race. During the first 4 h recovery, skiers received either water or carbohydrate (CHO) and thereafter all received CHO-enriched food. Immediately after the race, arm glycogen was reduced to 31 ± 4% and SR Ca2+ release rate decreased to 85 ± 2% of initial levels. Glycogen noticeably recovered after 4 h recovery with CHO (59 ± 5% initial) and the SR Ca2+ release rate returned to pre-exercise levels. However, in the absence of CHO during the first 4 h recovery, glycogen and the SR Ca2+ release rate remained unchanged (29 ± 2% and 77 ± 8%, respectively), with both parameters becoming normal after the remaining 18 h recovery with CHO. Leg muscle glycogen decreased to a lesser extent (71 ± 10% initial), with no effects on the SR Ca2+ release rate. Interestingly, transmission electron microscopy (TEM) analysis revealed that the specific pool of intramyofibrillar glycogen, representing 10–15% of total glycogen, was highly significantly correlated with the SR Ca2+ release rate. These observations strongly indicate that low glycogen and especially intramyofibrillar glycogen, as suggested by TEM, modulate the SR Ca2+ release rate in highly trained subjects. Thus, low glycogen during exercise may contribute to fatigue by causing a decreased SR Ca2+ release rate. PMID:21135051

Adsorption and release of biocides with mesoporous silica nanoparticles

NASA Astrophysics Data System (ADS)

Popat, Amirali; Liu, Jian; Hu, Qiuhong; Kennedy, Michael; Peters, Brenton; Lu, Gao Qing (Max); Qiao, Shi Zhang

2012-01-01

In this proof-of-concept study, an agricultural biocide (imidacloprid) was effectively loaded into the mesoporous silica nanoparticles (MSNs) with different pore sizes, morphologies and mesoporous structures for termite control. This resulted in nanoparticles with a large surface area, tunable pore diameter and small particle size, which are ideal carriers for adsorption and controlled release of imidacloprid. The effect of pore size, surface area and mesoporous structure on uptake and release of imidacloprid was systematically studied. It was found that the adsorption amount and release profile of imidacloprid were dependent on the type of mesoporous structure and surface area of particles. Specifically, MCM-48 type mesoporous silica nanoparticles with a three dimensional (3D) open network structure and high surface area displayed the highest adsorption capacity compared to other types of silica nanoparticles. Release of imidacloprid from these nanoparticles was found to be controlled over 48 hours. Finally, in vivo laboratory testing on termite control proved the efficacy of these nanoparticles as delivery carriers for biopesticides. We believe that the present study will contribute to the design of more effective controlled and targeted delivery for other biomolecules.In this proof-of-concept study, an agricultural biocide (imidacloprid) was effectively loaded into the mesoporous silica nanoparticles (MSNs) with different pore sizes, morphologies and mesoporous structures for termite control. This resulted in nanoparticles with a large surface area, tunable pore diameter and small particle size, which are ideal carriers for adsorption and controlled release of imidacloprid. The effect of pore size, surface area and mesoporous structure on uptake and release of imidacloprid was systematically studied. It was found that the adsorption amount and release profile of imidacloprid were dependent on the type of mesoporous structure and surface area of particles. Specifically, MCM-48 type mesoporous silica nanoparticles with a three dimensional (3D) open network structure and high surface area displayed the highest adsorption capacity compared to other types of silica nanoparticles. Release of imidacloprid from these nanoparticles was found to be controlled over 48 hours. Finally, in vivo laboratory testing on termite control proved the efficacy of these nanoparticles as delivery carriers for biopesticides. We believe that the present study will contribute to the design of more effective controlled and targeted delivery for other biomolecules. Electronic supplementary information (ESI) available. See DOI: 10.1039/c2nr11691j

Timing of translocation influences birth rate and population dynamics in a forest carnivore

USGS Publications Warehouse

Facka, Aaron N; Lewis, Jeffrey C.; Happe, Patricia; Jenkins, Kurt J.; Callas, Richard; Powell, Roger A.

2016-01-01

Timing can be critical for many life history events of organisms. Consequently, the timing of management activities may affect individuals and populations in numerous and unforeseen ways. Translocations of organisms are used to restore or expand populations but the timing of translocations is largely unexplored as a factor influencing population success. We hypothesized that the process of translocation negatively influences reproductive rates of individuals that are moved just before their birthing season and, therefore, the timing of releases could influence translocation success. Prior to reintroducing fishers (Pekania pennanti) into northern California and onto the Olympic Peninsula of Washington, we predicted that female fishers released in November and December (early) would have a higher probability of giving birth to kits the following March or April than females released in January, February, and March (late), just prior to or during the period of blastocyst implantation and gestation. Over four winters (2008–2011), we translocated 56 adult female fishers that could have given birth in the spring immediately after release. Denning rates, an index of birth rate, for females released early were 92% in California and 38% in Washington. In contrast, denning rates for females released late were 40% and 11%, in California and Washington, a net reduction in denning rate of 66% across both sites. To understand how releasing females nearer to parturition could influence population establishment and persistence, we used stochastic population simulations using three-stage Lefkovitch matrices. These simulations showed that translocating female fishers early had long-term positive influences on the mean population size and on quasi-extinction thresholds compared to populations where females were released late. The results from both empirical data and simulations show that the timing of translocation, with respect to life history events, should be considered during planning of translocations and implemented before the capture, movement, and release of organisms for translocation.

Effect of Stitching on Debonding in Composite Structural Elements

NASA Technical Reports Server (NTRS)

Raju, I. S.; Glaessgen, E. H.

2001-01-01

Stitched multiaxial warp knit materials have been suggested as viable alternatives to laminated prepreg materials for large aircraft structures such as wing skins. Analyses have been developed to quantify the effectiveness of stitching for reducing strain energy release rates in skin-stiffener debond, lap joint and sandwich debond configurations. Strain energy release rates were computed using the virtual crack closure technique. In all configurations, the stitches were shown to significantly reduce the strain energy release rate.

Chloride retention and release in a boreal forest soil: effects of soil water residence time and nitrogen and chloride loads.

PubMed

Bastviken, David; Sandén, Per; Svensson, Teresia; Ståhlberg, A Carina; Magounakis, Malin; Oberg, Gunilla

2006-05-01

The common assumption that chloride (Cl-) is conservative in soils and can be used as a groundwater tracer is currently being questioned, and an increasing number of studies indicate that Cl- can be retained in soils. We performed lysimeter experiments with soil from a coniferous forest in southeast Sweden to determine whether pore water residence time and nitrogen and Cl- loads affected Cl- retention. Over the first 42 days there was a net retention of Cl- with retention rates averaging 3.1 mg CI- m(-2) d(-1) (68% of the added Cl- retained over 42 days). Thereafter, a net release of Cl- at similar rates was observed for the remaining experimental period (85 d). Longer soil water residence time and higher Cl- load gave higher initial retention and subsequent release rates than shorter residence time and lower Cl- load did. Nitrogen load did not affect Cl transformation rates. This study indicates that simultaneous retention and release of Cl- can occur in soils, and that rates may be considerable relative to the load. The retention of Cl- observed was probably due to chlorination of soil organic matter or ion exchange. The cause of the shift between net retention and net release is unclear, but we hypothesize that the presence of O2 or the presence of microbially available organic matter regulates Cl- retention and release rates.

Influence of Finite Element Software on Energy Release Rates Computed Using the Virtual Crack Closure Technique

NASA Technical Reports Server (NTRS)

Krueger, Ronald; Goetze, Dirk; Ransom, Jonathon (Technical Monitor)

2006-01-01

Strain energy release rates were computed along straight delamination fronts of Double Cantilever Beam, End-Notched Flexure and Single Leg Bending specimens using the Virtual Crack Closure Technique (VCCT). Th e results were based on finite element analyses using ABAQUS# and ANSYS# and were calculated from the finite element results using the same post-processing routine to assure a consistent procedure. Mixed-mode strain energy release rates obtained from post-processing finite elem ent results were in good agreement for all element types used and all specimens modeled. Compared to previous studies, the models made of s olid twenty-node hexahedral elements and solid eight-node incompatible mode elements yielded excellent results. For both codes, models made of standard brick elements and elements with reduced integration did not correctly capture the distribution of the energy release rate acr oss the width of the specimens for the models chosen. The results suggested that element types with similar formulation yield matching results independent of the finite element software used. For comparison, m ixed-mode strain energy release rates were also calculated within ABAQUS#/Standard using the VCCT for ABAQUS# add on. For all specimens mod eled, mixed-mode strain energy release rates obtained from ABAQUS# finite element results using post-processing were almost identical to re sults calculated using the VCCT for ABAQUS# add on.

Reproduction and Development of the Released Przewalski’s Horses (Equus przewalskii) in Xinjiang, China

PubMed Central

CHEN, Jinliang; WENG, Qiang; CHAO, Jie; HU, Defu; TAYA, Kazuyoshi

2008-01-01

In China, the first Przewalski’s horse (Equus przewalskii) group was released in Kalamaili Ungulate Protected Area in Xinjiang, in August 2001. The objective of this study was to investigate reproduction and development of released Przewalski’s horses in Xinjiang, China from 2002 to 2006. Twenty-four descendants were naturally born, average reproduction rate was 38.7%, and average survival rate of foals was 69.1% in this interim. Frequent alternation of the leading stallion and infertility in female horses due to environmental factors were main causes for the low reproduction rate. The infant mortality rate of released Przewalski’s horses was 25.0%, and 83.3% of death in infants was due to the leading stallion infanticide. The released Przewalski’s horses exhibited seasonal breeding, 70.8% of infants were born in May and June. The fertility rates were 8.3% in April and 37.5% in May, which were lower compared to those of the captive Przewalski’s horse groups (18.3% and 44.3%, respectively). Furthermore, the fertility rate in June was 33.3% and higher than the captive groups (18.3%). These findings showed that the breeding peak of the released Przewalski’s horse groups was later than the captive groups, and suggested that the altered survival environment and food supplies were the main reasons contributing to the delayed breeding peak. PMID:24833949

Effect of sodium tripolyphosphate concentration and simulated gastrointestinal fluids on release profile of paracetamol from chitosan microsphere

NASA Astrophysics Data System (ADS)

Mulia, Kamarza; Andrie; Krisanti, Elsa A.

2018-03-01

The problem to overcome in oral drug administration is the significant pH changes present in the human digestive system. In this study, ionotropic gelation method employing 2-8% (w/v) tripolyphosphate solutions were used to crosslink chitosan microspheres for a controlled release of paracetamol as a model drug. The release profiles of paracetamol from chitosan microspheres were determined using simulated gastrointestinal fluids having pH values of 1.2, 6.8, and 7.4. The results showed that the paracetamol loading and the encapsulation efficiency values increased with increasing concentration of tripolyphosphate solutions used in the preparation step. Paracetamol released at pH 1.2 and 6.8 buffer solutions was significantly higher than that at pH 7.4; also, more paracetamol was released in the presence of α-amylase and β-glucosidase enzymes. The release profiles showed zero-order release behaviour up to 8 hours where the highest drug release was 39% of the paracetamol loaded in the chitosan microspheres, indicating a strong crosslinking between chitosan and TPP anions. The relatively low accumulated drug release could be compensated by employing suitable enzymes, lower TPP solution concentration, and addition of other biodegradable polymer to reduce the TPP crosslink.

Medium pH, carbon and nitrogen concentrations modulate the phosphate solubilization efficiency of Penicillium purpurogenum through organic acid production.

PubMed

Scervino, J M; Papinutti, V L; Godoy, M S; Rodriguez, M A; Della Monica, I; Recchi, M; Pettinari, M J; Godeas, A M

2011-05-01

To study phosphate solubilization in Penicillium purpurogenum as function of medium pH, and carbon and nitrogen concentrations. Tricalcium phosphate (CP) solubilization efficiency of P. purpurogenum was evaluated at acid or alkaline pH using different C and N sources. Glucose- and (NH(4) )(2) SO(4) -based media showed the highest P solubilization values followed by fructose. P. purpurogenum solubilizing ability was higher in cultures grown at pH 6·5 than cultures at pH 8·5. Organic acids were detected in both alkaline and neutral media, but the relative percentages of each organic acid differed. Highest P release coincided with the highest organic acids production peak, especially gluconic acid. When P. purpurogenum grew in alkaline media, the nature and concentration of organic acids changed at different N and C concentrations. A factorial categorical experimental design showed that the highest P-solubilizing activity, coinciding with the highest organic acid production, corresponded to the highest C concentration and lowest N concentration. The results described in the present study show that medium pH and carbon and nitrogen concentrations modulate the P solubilization efficiency of P. purpurogenum through the production of organic acids and particularly that of gluconic acid. In the P solubilization optimization studies, glucose and (NH(4) )(2) SO(4) as C and N sources allowed a higher solubilization efficiency at high pH. This organism is a potentially proficient soil inoculant, especially in P-poor alkaline soils where other P solubilizers fail to release soluble P. Further work is necessary to elucidate whether these results can be extrapolated to natural soil ecosystems, where different pH values are present. Penicillium purpurogenum could be used to develop a bioprocess for the manufacture of phosphatic fertilizer with phosphate calcium minerals. © 2011 The Authors. Journal of Applied Microbiology © 2011 The Society for Applied Microbiology.

Exploring virus release as a bottleneck for the spread of influenza A virus infection in vitro and the implications for antiviral therapy with neuraminidase inhibitors

PubMed Central

Kowal, Szymon; Cardenas, Daniel A.; Beauchemin, Catherine A. A.

2017-01-01

Mathematical models (MMs) have been used to study the kinetics of influenza A virus infections under antiviral therapy, and to characterize the efficacy of antivirals such as neuraminidase inhibitors (NAIs). NAIs prevent viral neuraminidase from cleaving sialic acid receptors that bind virus progeny to the surface of infected cells, thereby inhibiting their release, suppressing infection spread. When used to study treatment with NAIs, MMs represent viral release implicitly as part of viral replication. Consequently, NAIs in such MMs do not act specifically and exclusively on virus release. We compared a MM with an explicit representation of viral release (i.e., distinct from virus production) to a simple MM without explicit release, and investigated whether parameter estimation and the estimation of NAI efficacy were affected by the use of a simple MM. Since the release rate of influenza A virus is not well-known, a broad range of release rates were considered. If the virus release rate is greater than ∼0.1 h−1, the simple MM provides accurate estimates of infection parameters, but underestimates NAI efficacy, which could lead to underdosing and the emergence of NAI resistance. In contrast, when release is slower than ∼0.1 h−1, the simple MM accurately estimates NAI efficacy, but it can significantly overestimate the infectious lifespan (i.e., the time a cell remains infectious and producing free virus), and it will significantly underestimate the total virus yield and thus the likelihood of resistance emergence. We discuss the properties of, and a possible lower bound for, the influenza A virus release rate. PMID:28837615

[In vitro drug release behavior of carrier made of porous glass ceramics].

PubMed

Wang, De-ping; Huang, Wen-hai; Zhou, Nai

2002-09-01

To conduct the in vitro test on drug release of rifampin encapsulated in a carrier made of porous phosphate glass ceramics and to analyze main factors which affect the drug release rate. A certain quantitative of rifampin was sealed in a hollow cylindrical capsule which consisted of chopped calcium phosphate crystal fiber obtained from glass crystallization. The rifampin concentration was measured in the simulated physiological solution in which the capsule soaked. Rifampin could be released in a constant rate from the porous glass ceramic carrier in a long time. The release rate was dependent on the size of crystal fiber and the wall thickness of the capsule. This kind of calcium phosphate glass ceramics can be a candidate of the carrier materials used as long term drug therapy after osteotomy surgery.

Does infection tilt the scales? Disease effects on the mass balance of an invertebrate nutrient recycler.

PubMed

Narr, Charlotte F; Frost, Paul C

2015-12-01

While parasites are increasingly recognized as important components of ecosystems, we currently know little about how they alter ecosystem nutrient availability via host-mediated nutrient cycling. We examined whether infection alters the flow of nutrients through hosts and whether such effects depend upon host diet quality. To do so, we compared the mass specific nutrient (i.e., nitrogen and phosphorus) release rates, ingestion rates, and elemental composition of uninfected Daphnia to those infected with a bacterial parasite, P. ramosa. N and P release rates were increased by infection when Daphnia were fed P-poor diets, but we found no effect of infection on the nutrient release of individuals fed P-rich diets. Calculations based on the first law of thermodynamics indicated that infection should increase the nutrient release rates of Daphnia by decreasing nutrient accumulation rates in host tissues. Although we found reduced nutrient accumulation rates in infected Daphnia fed all diets, this reduction did not increase the nutrient release rates of Daphnia fed the P-rich diet because infected Daphnia fed this diet ingested nutrients more slowly than uninfected hosts. Our results thus indicate that parasites can significantly alter the nutrient use of animal consumers, which could affect the availability of nutrients in heavily parasitized environments.

Mating competitiveness of male Anopheles arabiensis mosquitoes irradiated with a partially or fully sterilizing dose in small and large laboratory cages.

PubMed

Helinski, M E H; Knols, B G J

2008-07-01

Male mating competitiveness is a crucial parameter in many genetic control programs including the sterile insect technique (SIT). We evaluated competitiveness of male Anopheles arabiensis Patton as a function of three experimental variables: (1) small or large cages for mating, (2) the effects of either a partially sterilizing (70 Gy) or fully sterilizing (120 Gy) dose, and (3) pupal or adult irradiation. Irradiated males competed for females with an equal number of unirradiated males. Competitiveness was determined by measuring hatch rates of individually laid egg batches. In small cages, pupal irradiation with the high dose resulted in the lowest competitiveness, whereas adult irradiation with the low dose gave the highest, with the latter males being equal in competitiveness to unirradiated males. In the large cage, reduced competitiveness of males irradiated in the pupal stage was more pronounced compared with the small cage; the males irradiated as adults at both doses performed similarly to unirradiated males. Unexpectedly, males irradiated with the high dose performed better in a large cage than in a small one. A high proportion of intermediate hatch rates was observed for eggs collected in the large cage experiments with males irradiated at the pupal stage. It is concluded that irradiation of adult An. arabiensis with the partially sterilizing dose results in the highest competitiveness for both cage designs. Cage size affected competitiveness for some treatments; therefore, competitiveness determined in laboratory experiments must be confirmed by releases into simulated field conditions. The protocols described are readily transferable to evaluate male competitiveness for other genetic control techniques.

Peat accumulation in drained thermokarst lake basins in continuous, ice-rich permafrost, northern Seward Peninsula, Alaska

USGS Publications Warehouse

Jones, Miriam C.; Grosse, Guido; Jones, Benjamin M.; Anthony, Katey Walter

2012-01-01

Thermokarst lakes and peat-accumulating drained lake basins cover a substantial portion of Arctic lowland landscapes, yet the role of thermokarst lake drainage and ensuing peat formation in landscape-scale carbon (C) budgets remains understudied. Here we use measurements of terrestrial peat thickness, bulk density, organic matter content, and basal radiocarbon age from permafrost cores, soil pits, and exposures in vegetated, drained lake basins to characterize regional lake drainage chronology, C accumulation rates, and the role of thermokarst-lake cycling in carbon dynamics throughout the Holocene on the northern Seward Peninsula, Alaska. Most detectable lake drainage events occurred within the last 4,000 years with the highest drainage frequency during the medieval climate anomaly. Peat accumulation rates were highest in young (50–500 years) drained lake basins (35.2 g C m−2 yr−1) and decreased exponentially with time since drainage to 9 g C m−2 yr−1 in the oldest basins. Spatial analyses of terrestrial peat depth, basal peat radiocarbon ages, basin geomorphology, and satellite-derived land surface properties (Normalized Difference Vegetation Index (NDVI); Minimum Noise Fraction (MNF)) from Landsat satellite data revealed significant relationships between peat thickness and mean basin NDVI or MNF. By upscaling observed relationships, we infer that drained thermokarst lake basins, covering 391 km2 (76%) of the 515 km2 study region, store 6.4–6.6 Tg organic C in drained lake basin terrestrial peat. Peat accumulation in drained lake basins likely serves to offset greenhouse gas release from thermokarst-impacted landscapes and should be incorporated in landscape-scale C budgets.

Dissolution kinetics of iron-, manganese-, and copper-containing synthetic hydroxyapatites

NASA Technical Reports Server (NTRS)

Sutter, B.; Hossner, L. R.; Ming, D. W.

2005-01-01

Micronutrient-substituted synthetic hydroxyapatite (SHA) is being evaluated by the National Aeronautics and Space Administration's (NASA) Advanced Life Support (ALS) Program for crop production on long-duration human missions to the International Space Station or for future Lunar or Martian outposts. The stirred-flow technique was utilized to characterize Ca, P, Fe, Mn, and Cu release characteristics from Fe-, Mn-, and Cu-containing SHA in deionized (DI) water, citric acid, and diethylene-triamine-pentaacetic acid (DTPA). Initially, Ca and P release rates decreased rapidly with time and were controlled by a non-SHA calcium phosphate phase(s) with low Ca/P solution molar ratios (0.91-1.51) relative to solid SHA ratios (1.56-1.64). At later times, Ca/P solution molar ratios (1.47-1.79) were near solid SHA ratios and release rates decreased slowly indicating that SHA controlled Ca and P release. Substituted SHA materials had faster dissolution rates relative to unsubstituted SHA. The initial metal release rate order was Mn >> Cu > Fe which followed metal-oxide/phosphate solubility suggesting that poorly crystalline metal-oxides/phosphates were dominating metal release. Similar metal release rates for all substituted SHA (approximately 0.01 cmol kg-1 min-1) at the end of the DTPA experiment indicated that SHA dissolution was supplying the metals into solution and that poorly crystalline metal-oxide/phosphates were not controlling metal release. Results indicate that non-SHA Ca-phosphate phases and poorly crystalline metal-oxide/phosphates will contribute Ca, P, and metals. After these phases have dissolved, substituted SHA will be the source of Ca, P, and metals for plants.

Plant litter decomposition and nutrient release in peatlands

NASA Astrophysics Data System (ADS)

Bragazza, Luca; Buttler, Alexandre; Siegenthaler, Andy; Mitchell, Edward A. D.

Decomposition of plant litter is a crucial process in controlling the carbon balance of peatlands. Indeed, as long as the rate of litter decomposition remains lower than the rate of above- and belowground litter production, a net accumulation of peat and, thus, carbon will take place. In addition, decomposition controls the release of important nutrients such as nitrogen, phosphorus, and potassium, the availability of which affects the structure and the functioning of plant communities. This chapter describes the role of the main drivers in affecting mass loss and nutrient release from recently deposited plant litter. In particular, the rate of mass loss of Sphagnum litter and vascular plant litter is reviewed in relation to regional climatic conditions, aerobic/anaerobic conditions, and litter chemistry. The rate of nutrient release is discussed in relation to the rate of mass loss and associated litter chemistry by means of a specific case study.

3D DNS of Turbulent Premixed Flame with over 50 Species and 300 Elementary Reactions

NASA Astrophysics Data System (ADS)

Shimura, Masayasu; Yenerdag, Basmil; Naka, Yoshitsugu; Nada, Yuzuru; Tanahashi, Mamoru

2014-11-01

Three-dimensional direct numerical simulation of methane-air premixed planar flame propagating in homogenous isotropic turbulence is conducted to investigate local flame structure in thin reaction zones. Detailed kinetic mechanism, GRI-Mech 3.0 which includes 53 species and 325 elementary reactions, is used to represent methane-air reaction, and temperature dependences of transport and thermal properties are considered. For a better understanding of the local flame structure in thin reaction zones regime, distributions of mass fractions of major species, heat release rate, temperature and turbulent structures are investigated. Characteristic flame structures, such as radical fingering and multi-layered-like flame structures, are observed. The most expected maximum heat release rate in flame elements is lower than that of laminar flame with same mixture. To clarify mechanism of the decrease in local heat release rate, effects of strain rates tangential to flame front on local heat release rate are investigated.

Adult Survivorship of the Dengue Mosquito Aedes aegypti Varies Seasonally in Central Vietnam

PubMed Central

Hugo, Leon E.; Jeffery, Jason A. L.; Trewin, Brendan J.; Wockner, Leesa F.; Thi Yen, Nguyen; Le, Nguyen Hoang; Nghia, Le Trung; Hine, Emma; Ryan, Peter A.; Kay, Brian H.

2014-01-01

The survival characteristics of the mosquito Aedes aegypti affect transmission rates of dengue because transmission requires infected mosquitoes to survive long enough for the virus to infect the salivary glands. Mosquito survival is assumed to be high in tropical, dengue endemic, countries like Vietnam. However, the survival rates of wild populations of mosquitoes are seldom measured due the difficulty of predicting mosquito age. Hon Mieu Island in central Vietnam is the site of a pilot release of Ae. aegypti infected with a strain of Wolbachia pipientis bacteria (wMelPop) that induces virus interference and mosquito life-shortening. We used the most accurate mosquito age grading approach, transcriptional profiling, to establish the survival patterns of the mosquito population from the population age structure. Furthermore, estimations were validated on mosquitoes released into a large semi-field environment consisting of an enclosed house, garden and yard to incorporate natural environmental variability. Mosquito survival was highest during the dry/cool (January-April) and dry/hot (May-August) seasons, when 92 and 64% of Hon Mieu mosquitoes had survived to an age that they were able to transmit dengue (12 d), respectively. This was reduced to 29% during the wet/cool season from September to December. The presence of Ae. aegypti older than 12 d during each season is likely to facilitate the observed continuity of dengue transmission in the region. We provide season specific Ae. aegypti survival models for improved dengue epidemiology and evaluation of mosquito control strategies that aim to reduce mosquito survival to break the dengue transmission cycle. PMID:24551251

Dust release rates and dust-to-gas mass ratios of eight comets

NASA Technical Reports Server (NTRS)

Singh, P. D.; De Almeida, A. A.; Huebner, W. F.

1992-01-01

Mass release rates of dust and mass ratios of dust-to-gas release rates of Comets Thiele (1985m), Wilson (1986l), P/Borrelly (1987p), Liller (1988a), Bradfield (1987s), Hartley-Good (1985l), P/Giacobini-Zinner (1984e), and P/Halley (1982i) are estimated from the analysis of continuum flux measurements at optical wavelengths. An attempt is made to estimate the size of each comet nucleus on the basis of water-ice sublimation (vaporization), assuming that the nucleus is spherical and only a fraction of its surface area is active. Where possible, the dust mass release rates are compared with those obtained by other investigators in the optical and IR wavelength regions. Good agreement with results based on IR observations is found.

Gas Release as a Deformation Signal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bauer, Stephen J.

Radiogenic noble gases are contained in crustal rock at inter and intra granular sites. The gas composition depends on lithology, geologic history, fluid phases, and the aging effect by decay of U, Th, and K. The isotopic signature of noble gases found in rocks is vastly different than that of the atmosphere which is contributed by a variety of sources. When rock is subjected to stress conditions exceeding about half its yield strength, micro-cracks begin to form. As rock deformation progresses a fracture network evolves, releasing trapped noble gases and changing the transport properties to gas migration. Thus, changes inmore » gas emanation and noble gas composition from rocks could be used to infer changes in stress-state and deformation. The purpose of this study has been to evaluate the effect of deformation/strain rate upon noble gas release. Four triaxial experiments were attempted for a strain rate range of %7E10-8 /s (180,000s) to %7E 10-4/s (500s); the three fully successful experiments (at the faster strain rates) imply the following: (1) helium is measurably released for all strain rates during deformation, this release is in amounts 1-2 orders of magnitude greater than that present in the air, and (2) helium gas release increases with decreasing strain rate.« less

Effect of amine functionalization of spherical MCM-41 and SBA-15 on controlled drug release

DOE Office of Scientific and Technical Information (OSTI.GOV)

Szegedi, A., E-mail: szegedi@chemres.h; Popova, M.; Goshev, I.

2011-05-15

MCM-41 and SBA-15 silica materials with spherical morphology and different particle sizes were synthesized and modified by post-synthesis method with 3-aminopropyltriethoxysilane (APTES). A comparative study of the adsorption and release of a model drug, ibuprofen, were carried out. The modified and drug loaded mesoporous materials were characterized by XRD, TEM, N{sub 2} physisorption, thermal analysis, elemental analysis and FT-IR spectroscopy. Surface modification with amino groups resulted in high degree of ibuprofen loading and slow rate of release for MCM-41, whereas it was the opposite for SBA-15. The adsorbed drug content and the delivery rate can be predetermined by the choicemore » of mesoporous material with the appropriate structural characteristics and surface functionality. -- Graphical Abstract: Ibuprofen delivery from the parent and amino-modified spherical MCM-41 materials with 100 nm (small) and 500 nm (large) particle sizes. Display Omitted Highlights: {yields} Spherical type MCM-41 and SBA-15 with different particle sizes were modified by APTES. {yields} Adsorption and release rate of ibuprofen were compared. {yields} High degree of ibuprofen loading, slow release rate for MCM-41, the opposite for SBA-15. {yields} MCM-41 with 100 nm particles was more stable and showed slower release rate« less

Sexual content in video games: an analysis of the Entertainment Software Rating Board classification from 1994 to 2013.

PubMed

Vidaña-Pérez, Dèsirée; Braverman-Bronstein, Ariela; Basto-Abreu, Ana; Barrientos-Gutierrez, Inti; Hilscher, Rainer; Barrientos-Gutierrez, Tonatiuh

2018-01-11

Background: Video games are widely used by children and adolescents and have become a significant source of exposure to sexual content. Despite evidence of the important role of media in the development of sexual attitudes and behaviours, little attention has been paid to monitor sexual content in video games. Methods: Data was obtained about sexual content and rating for 23722 video games from 1994 to 2013 from the Entertainment Software Rating Board database; release dates and information on the top 100 selling video games was also obtained. A yearly prevalence of sexual content according to rating categories was calculated. Trends and comparisons were estimated using Joinpoint regression. Results: Sexual content was present in 13% of the video games. Games rated 'Mature' had the highest prevalence of sexual content (34.5%) followed by 'Teen' (30.7%) and 'E10+' (21.3%). Over time, sexual content decreased in the 'Everyone' category, 'E10+' maintained a low prevalence and 'Teen' and 'Mature' showed a marked increase. Both top and non-top video games showed constant increases, with top selling video games having 10.1% more sexual content across the period of study. Conclusion: Over the last 20 years, the prevalence of sexual content has increased in video games with a 'Teen' or 'Mature' rating. Further studies are needed to quantify the potential association between sexual content in video games and sexual behaviour in children and adolescents.

14 CFR 121.312 - Materials for compartment interiors.

Code of Federal Regulations, 2011 CFR

2011-01-01

... prior to August 20, 1990, must comply with the heat release rate testing provisions of § 25.853(d) in...), except that the total heat release over the first 2 minutes of sample exposure must not exceed 100 kilowatt minutes per square meter and the peak heat release rate must not exceed 100 kilowatts per square...

14 CFR 121.312 - Materials for compartment interiors.

Code of Federal Regulations, 2010 CFR

2010-01-01

... prior to August 20, 1990, must comply with the heat release rate testing provisions of § 25.853(d) in...), except that the total heat release over the first 2 minutes of sample exposure must not exceed 100 kilowatt minutes per square meter and the peak heat release rate must not exceed 100 kilowatts per square...

14 CFR 121.312 - Materials for compartment interiors.

Code of Federal Regulations, 2012 CFR

2012-01-01

... prior to August 20, 1990, must comply with the heat release rate testing provisions of § 25.853(d) in...), except that the total heat release over the first 2 minutes of sample exposure must not exceed 100 kilowatt minutes per square meter and the peak heat release rate must not exceed 100 kilowatts per square...

14 CFR 135.170 - Materials for compartment interiors.

Code of Federal Regulations, 2011 CFR

2011-01-01

... August 20, 1990, must comply with the heat release rate testing provisions of § 25.853(d) in effect March 6, 1995 (formerly § 25.853(a-1) in effect on August 20, 1986), except that the total heat release... and the peak heat release rate must not exceed 100 kilowatts per square meter. (ii) Each airplane with...

14 CFR 135.170 - Materials for compartment interiors.

Code of Federal Regulations, 2012 CFR

2012-01-01

... August 20, 1990, must comply with the heat release rate testing provisions of § 25.853(d) in effect March 6, 1995 (formerly § 25.853(a-1) in effect on August 20, 1986), except that the total heat release... and the peak heat release rate must not exceed 100 kilowatts per square meter. (ii) Each airplane with...

14 CFR 121.312 - Materials for compartment interiors.

Code of Federal Regulations, 2013 CFR

2013-01-01

... prior to August 20, 1990, must comply with the heat release rate testing provisions of § 25.853(d) in...), except that the total heat release over the first 2 minutes of sample exposure must not exceed 100 kilowatt minutes per square meter and the peak heat release rate must not exceed 100 kilowatts per square...

14 CFR 135.170 - Materials for compartment interiors.

Code of Federal Regulations, 2014 CFR

2014-01-01

... August 20, 1990, must comply with the heat release rate testing provisions of § 25.853(d) in effect March 6, 1995 (formerly § 25.853(a-1) in effect on August 20, 1986), except that the total heat release... and the peak heat release rate must not exceed 100 kilowatts per square meter. (ii) Each airplane with...

14 CFR 135.170 - Materials for compartment interiors.

Code of Federal Regulations, 2013 CFR

2013-01-01

... August 20, 1990, must comply with the heat release rate testing provisions of § 25.853(d) in effect March 6, 1995 (formerly § 25.853(a-1) in effect on August 20, 1986), except that the total heat release... and the peak heat release rate must not exceed 100 kilowatts per square meter. (ii) Each airplane with...

14 CFR 121.312 - Materials for compartment interiors.

Code of Federal Regulations, 2014 CFR

2014-01-01

... prior to August 20, 1990, must comply with the heat release rate testing provisions of § 25.853(d) in...), except that the total heat release over the first 2 minutes of sample exposure must not exceed 100 kilowatt minutes per square meter and the peak heat release rate must not exceed 100 kilowatts per square...

14 CFR 135.170 - Materials for compartment interiors.

Code of Federal Regulations, 2010 CFR

2010-01-01

... August 20, 1990, must comply with the heat release rate testing provisions of § 25.853(d) in effect March 6, 1995 (formerly § 25.853(a-1) in effect on August 20, 1986), except that the total heat release... and the peak heat release rate must not exceed 100 kilowatts per square meter. (ii) Each airplane with...

The Relationship between Toxics Release Inventory Discharges and Mortality Rates in Rural and Urban Areas of the United States

ERIC Educational Resources Information Center

Hendryx, Michael; Fedorko, Evan

2011-01-01

Background: Potential environmental exposures from chemical manufacturing or industrial sites have not been well studied for rural populations. The current study examines whether chemical releases from facilities monitored through the Toxics Release Inventory (TRI) program are associated with population mortality rates for both rural and urban…

Encapsulation of Ethylene Gas into Granular Cold-Water-Soluble Starch: Structure and Release Kinetics.

PubMed

Shi, Linfan; Fu, Xiong; Tan, Chin Ping; Huang, Qiang; Zhang, Bin

2017-03-15

Ethylene gas was introduced into granular cold-water-soluble (GCWS) starches using a solid encapsulation method. The morphological and structural properties of the novel inclusion complexes (ICs) were characterized using scanning electron microscopy, X-ray diffractometry, and Raman spectroscopy. The V-type single helix of GCWS starches was formed through controlled gelatinization and ethanol precipitation and was approved to host ethylene gas. The controlled release characteristics of ICs were also investigated at various temperature and relative humidity conditions. Avrami's equation was fitted to understand the release kinetics and showed that the release of ethylene from the ICs was accelerated by increasing temperature or RH and was decelerated by increased degree of amylose polymerization. The IC of Hylon-7 had the highest ethylene concentration (31.8%, w/w) among the five starches, and the IC of normal potato starch showed the best controlled release characteristics. As a renewable and inexpensive material, GCWS starch is a desirable solid encapsulation matrix with potential in agricultural and food applications.

The sludge loading rate regulates the growth and release of heterotrophic bacteria resistant to six types of antibiotics in wastewater activated sludge.

PubMed

Yuan, Qing-Bin; Guo, Mei-Ting; Yang, Jian

2015-01-01

Wastewater treatment plants are considered as hot reservoirs of antimicrobial resistance. However, the fates of antibiotic-resistant bacteria during biological treatment processes and relevant influencing factors have not been fully understood. This study evaluated the effects of the sludge loading rate on the growth and release of six kinds of antibiotic-resistant bacteria in an activated sludge system. The results indicated that higher sludge loading rates amplified the growth of all six types of antibiotic resistant bacteria. The release of most antibiotic-resistant bacteria through both the effluent and biosolids was amplified with increased sludge loading rate. Biosolids were the main pattern for all antibiotic-resistant bacteria release in an activated sludge system, which was determined primarily by their growth in the activated sludge. A higher sludge loading rate reactor tended to retain more antibiotic resistance. An activated sludge system with lower sludge loading rates was considered more conducive to the control of antibiotic resistance.

Reduction of calcium inactivation of sarcoplasmic reticulum calcium release by fura-2 in voltage-clamped cut twitch fibers from frog muscle

PubMed Central

1993-01-01

Cut fibers from Rana temporaria and Rana pipiens (striation spacing, 3.9-4.2 microns) were mounted in a double Vaseline-gap chamber and studied at 14 degrees C. The Ca indicator purpurate-3,3' diacetic acid (PDAA) was introduced into the end pools and allowed to diffuse into the optical recording site. When the concentration at the site exceeded 2 mM, step depolarizations to 10 mV were applied and the [Ca] transient measured with PDAA was used to estimate Ca release from the sarcoplasmic reticulum (SR) (Baylor, S. M., W. K. Chandler, and M. W. Marshall. 1983. Journal of Physiology. 344:625-666). With depolarization, the rate of SR Ca release increased to an early peak and then rapidly decreased several-fold to a quasi-steady level. The total amount of Ca released from the SR at the time of peak rate of release appeared to be independent of SR Ca content, consistent with the idea that a single activated channel might pass, on average, a fixed number of ions, independent of the magnitude of the single channel flux. A possible explanation of this property is given in terms of locally induced Ca inactivation of Ca release. The solution in the end pools was then changed to one with PDAA plus fura-2. SR Ca release was estimated from the [Ca] transient, as before, and from the delta [Cafura-2] signal. On average, 2-3 mM fura-2 increased the quasi-steady level of the rate of SR Ca release by factors of 6.6 and 3.8, respectively, in three fibers from Rana temporaria and three fibers from Rana pipiens. The peak rate of release was increased in five of the six fibers but to a lesser extent than the quasi-steady level. In all fibers, the amplitude of the free [Ca] transient was markedly reduced. These increases in the rate of SR Ca release are consistent with the idea that Ca inactivation of Ca release develops during a step depolarization to 10 mV and that 2-3 mM fura-2 is able to reduce this inactivation by complexing Ca and thereby reducing free [Ca]. Once the concentration of fura-2 becomes sufficiently large, a further increase reduces the rate of SR Ca release. On average, 5-6 mM fura-2 increased the quasi-steady rate of release, compared with 0 mM fura-2, by 6.5 and 2.9, respectively, in four fibers from Rana temporaria and three from Rana pipiens.(ABSTRACT TRUNCATED AT 400 WORDS) PMID:8228914

The impact of a parkinsonian lesion on dynamic striatal dopamine transmission depends on nicotinic receptor activation

PubMed Central

Jennings, Katie A.; Platt, Nicola J.; Cragg, Stephanie J.

2015-01-01

Dopamine function is disturbed in Parkinson's disease (PD), but whether and how release of dopamine from surviving neurons is altered has long been debated. Nicotinic acetylcholine receptors (nAChRs) on dopamine axons powerfully govern dopamine release and could be critical contributing factors. We revisited whether fundamental properties of dopamine transmission are changed in a parkinsonian brain and tested the potentially profound masking effects of nAChRs. Using real-time detection of dopamine in mouse striatum after a partial 6-hydroxydopamine lesion and under nAChR inhibition, we reveal that dopamine signals show diminished sensitivity to presynaptic activity. This effect manifested as diminished contrast between DA release evoked by the lowest versus highest frequencies. This reduced activity-dependence was underpinned by loss of short-term facilitation of dopamine release, consistent with an increase in release probability (Pr). With nAChRs active, the reduced activity-dependence of dopamine release after a parkinsonian lesion was masked. Consequently, moment-by-moment variation in activity of nAChRs may lead to dynamic co-variation in dopamine signal impairments in PD. PMID:26117304

Algal antifouling and fouling-release properties of metal surfaces coated with a polymer inspired by marine mussels.

PubMed

Statz, Andrea; Finlay, John; Dalsin, Jeffrey; Callow, Maureen; Callow, James A; Messersmith, Phillip B

2006-01-01

The marine antifouling and fouling-release performance of titanium surfaces coated with a bio-inspired polymer was investigated. The polymer consisted of methoxy-terminated poly(ethylene glycol) (mPEG) conjugated to the adhesive amino acid l-3,4-dihydroxyphenylalanine (DOPA) and was chosen based on its successful resistance to protein and mammalian cell fouling. Biofouling assays for the settlement and release of the diatom Navicula perminuta and settlement, growth and release of zoospores and sporelings (young plants) of the green alga Ulva linza were carried out. Results were compared to glass, a poly(dimethylsiloxane) elastomer (Silastic T2) and uncoated Ti. The mPEG-DOPA3 modified Ti surfaces exhibited a substantial decrease in attachment of both cells of N. perminuta and zoospores of U. linza as well as the highest detachment of attached cells under flow compared to control surfaces. The superior performance of this polymer over a standard silicone fouling-release coating in diatom assays and approximately equivalent performance in zoospore assays suggests that this bio-inspired polymer may be effective in marine antifouling and fouling-release applications.

Correlates to colonizations of new patches by translocated populations of bighorn sheep

USGS Publications Warehouse

Singer, F.J.; Moses, M.E.; Bellew, S.; Sloan, W.

2000-01-01

By 1950, bighorn sheep were extirpated from large areas of their range. Most extant populations of bighorn sheep (Ovis canadensis) in the Intermountain West consist of <100 individuals occurring in a fragmented distribution across the landscape. Dispersal and successful colonizations of unoccupied habitat patches has been rarely reported, and, in particular, translocated populations have been characterized by limited population growth and limited dispersal rates. Restoration of the species is greatly assisted by dispersal and successful colonization of new patches within a metapopulation structure versus the existing scenario of negligible dispersal and fragmented, small populations. We investigated the correlates for the rate of colonizations of 79 suitable, but unoccupied, patches by 31 translocated populations of bighorn sheep released into nearby patches of habitat. Population growth rates of bighorn sheep in the release patches were correlated to Ne of the founder group, and early contact with a second released population in a nearby release patch (logistic regression, p = 0.08). Largest population size of all extant released populations in 1994 was correlated to potential Ne of the founder group, the number of different source populations represented in the founder, and early contact with a second released population (p = 0.016). Dispersal rates were 100% higher in rams than ewes (p = 0.001). Successful colonizations of unoccupied patches (n = 24 of 79 were colonized) were associated with rapid growth rates in the released population, years since release, larger area of suitable habitat in the release patch, larger population sizes, and a seasonal migratory tendency in the released population (p = 0.05). Fewer water barriers, more open vegetation and more rugged, broken terrain in the intervening habitat were also associated with colonizations (p = <0.05). We concluded that high dispersal rates and rapid reoccupation of large areas could occur if bighorn sheep are placed in large patches of habitat with few barriers to movements to other patches and with no domestic sheep present. Many restorations in the past that did not meet these criteria may have contributed to an insular population structure of bighorn sheep with limited observations of dispersal.

Correlates to colonizations of new patches by translocated populations of bighorn sheep

USGS Publications Warehouse

Singer, F.J.; Moses, M.E.; Bellew, S.; Sloan, W.

2000-01-01

By 1950, bighorn sheep were extirpated from large areas of their range. Most extant populations of bighorn sheep (Ovis canadensis) in the Intermountain West consist of <100 individuals occurring in a fragmented distribution across the landscape. Dispersal and successful colonizations of unoccupied habitat patches has been rarely reported, and, in particular, translocated populations have been characterized by limited population growth and limited dispersal rates. Restoration of the species is greatly assisted by dispersal and successful colonization of new patches within a metapopulation structure versus the existing scenario of negligible dispersal and fragmented, small populations. We investigated the correlates for the rate of colonizations of 79 suitable, but unoccupied, patches by 31 translocated populations of bighorn sheep released into nearby patches of habitat. Population growth rates of bighorn sheep in the release patches were correlated to Ne of the founder group, and early contact with a second released population in a nearby release patch (logistic regression, p = 0.08). Largest population size of all extant released populations in 1994 was correlated to potential Ne of the founder group, the number of different source populations represented in the founder, and early contact with a second released population (p = 0.016). Dispersal rates were 100% higher in rams than ewes (p = 0.001). Successful colonizations of unoccupied patches (n = 24 of 79 were colonized) were associated with rapid growth rates in the released population, years since release, larger area of suitable habitat in the release patch, larger population sizes, and a seasonal migratory tendency in the released population (p = 0.05). Fewer water barriers, more open vegetation and more rugged, broken terrain in the intervening habitat were also associated with colonizations (p = <0.05). We concluded that high dispersal rates and rapid reoccupation of large areas could occur if bighorn sheep are placed in large patches of habitat with few barriers to movements to other patches and with no domestic sheep present. Many restorations in the past that did not meet these criteria may have contributed to an insular population structure of bighorn sheep with limited observations of dispersal.

Release of Water Soluble Drugs from Dynamically Swelling POLY(2-HYDROXYETHYL Methacrylate - CO - Methacrylic Acid) Hydrogels.

NASA Astrophysics Data System (ADS)

Kou, Jim Hwai-Cher

In this study, ionizable copolymers of HEMA and methacrylic acid (MA) are investigated for their potential use in developing pH dependent oral delivery systems. Because of the MA units, these gels swell extensively at high pH. Since solute diffusion in the hydrophilic polymers depends highly on the water content of the matrix, it is anticipated that the release rate will be modulated by this pH induced swelling. From a practical point of view, the advantage of the present system is that one can minimize drug loss in the stomach and achieve a programmed release in intestine. This approach is expected to improve delivery of acid labile drugs or drugs that cause severe gastrointestinal side effects. This work mainly focuses on the basic understanding of the mechanism involved in drug release from the poly(HEMA -co- MA) gels, especially under dynamic swelling conditions. Equilibrium swelling is first characterized since water content is the major determinant of transport properties in these gels. Phenylpropanolamine (PPA) is chosen as the model drug for the release study and its diffusion characteristics in the gel matrix determined. The data obtained show that the PPA diffusivity follows the free volume theory of Yasuda, which explains the accelerating effect of swelling on drug release. A mathematical model based on a diffusion mechanism has been developed to describe PPA release from the swelling gels. Based on this model, several significant conclusions can be drawn. First, the release rate can be modulated by the aspect ratio of the cylindrical geometry, and this has a practical implication in dosage form design. Second, the release rate can be lowered quite considerably if the dimensional increase due to swelling is significant. Consequently, it is the balance between the drug diffusivity increase and the gel dimensional growth that determines the release rate from the swelling matrix. Third, quasi-steady release kinetics, which are characteristic of swelling release systems, can also be predicted by this model. PPA release from initially dry poly(HEMA -co- MA) gels has also been studied. The data show that the release rate is mainly controlled by the PPA loading level and quite insensitive to the methacrylic acid composition of the gels. These phenomena can be adequately explained by analyzing the transport resistances in the gels. The overall time scale of release from these gels were shown to be in the range which was suitable for oral controlled release applications. (Abstract shortened with permission of author.).

Controlling Stimulated Brillouin/Raman Scattering in High Power Fiber Lasers

DTIC Science & Technology

2017-08-09

inversion curve (green)……………….……….40 Figure 22: A schematic of the counter-pumped amplifier is shown above………….…..41 Figure 23: A temporal response of...excites electrons to the upper state, N2, and provides inversion for all other signals. The laser 6 Approved for public release. Distribution is...as is the case below, the Stokes light will have its highest fields present at the z = 0 boundary of the fiber where the highest levels of inversion

The Dynamics of Pheromone Gland Synthesis and Release: a Paradigm Shift for Understanding Sex Pheromone Quantity in Female Moths.

PubMed

Foster, Stephen P; Anderson, Karin G; Casas, Jérôme

2018-05-10

Moths are exemplars of chemical communication, especially with regard to specificity and the minute amounts they use. Yet, little is known about how females manage synthesis and storage of pheromone to maintain release rates attractive to conspecific males and why such small amounts are used. We developed, for the first time, a quantitative model, based on an extensive empirical data set, describing the dynamical relationship among synthesis, storage (titer) and release of pheromone over time in a moth (Heliothis virescens). The model is compartmental, with one major state variable (titer), one time-varying (synthesis), and two constant (catabolism and release) rates. The model was a good fit, suggesting it accounted for the major processes. Overall, we found the relatively small amounts of pheromone stored and released were largely a function of high catabolism rather than a low rate of synthesis. A paradigm shift may be necessary to understand the low amounts released by female moths, away from the small quantities synthesized to the (relatively) large amounts catabolized. Future research on pheromone quantity should focus on structural and physicochemical processes that limit storage and release rate quantities. To our knowledge, this is the first time that pheromone gland function has been modeled for any animal.

An Indirect Role for Ethylene in Shoot-inversion Release of Apical Dominance in Pharbitis Nil

NASA Technical Reports Server (NTRS)

Cline, M. G.

1985-01-01

Evidence is presented which indicated that ethylene does not play a direct role in promoting or inhibiting bud outgrowth as a gravity response. It is concluded that the treatment of inactive or induced lateral buds with ethylene inhibitors or ethrel has no significant effect on bud outgrowth and that no changes occur in ethylene emanation in the Highest Lateral Bud (HLB) or HLB node following shoot inversion. Possible mechanisms by which ethylene released by shoot inversion may indirectly promote outgrowth of the HLB is presented.

Optimization of Eisenia fetida stocking density for the bioconversion of rock phosphate enriched cow dung-waste paper mixtures.

PubMed

Unuofin, F O; Mnkeni, P N S

2014-11-01

Vermitechnology is gaining recognition as an environmental friendly waste management strategy. Its successful implementation requires that the key operational parameters like earthworm stocking density be established for each target waste/waste mixture. One target waste mixture in South Africa is waste paper mixed with cow dung and rock phosphate (RP) for P enrichment. This study sought to establish optimal Eisenia fetida stocking density for maximum P release and rapid bioconversion of RP enriched cow dung-paper waste mixtures. E. fetida stocking densities of 0, 7.5, 12.5, 17.5 and 22.5 g-worms kg(-1) dry weight of cow dung-waste paper mixtures were evaluated. The stocking density of 12.5 g-worms kg(-1) resulted in the highest earthworm growth rate and humification of the RP enriched waste mixture as reflected by a C:N ratio of <12 and a humic acid/fulvic acid ratio of >1.9 in final vermicomposts. A germination test revealed that the resultant vermicompost had no inhibitory effect on the germination of tomato, carrot, and radish. Extractable P increased with stocking density up to 22.5 g-worm kg(-1) feedstock suggesting that for maximum P release from RP enriched wastes a high stocking density should be considered. Copyright © 2014. Published by Elsevier Ltd.

Antimatter propulsion, status and prospects

NASA Technical Reports Server (NTRS)

Howe, Steven D.; Hynes, Michael V.

1986-01-01

The use of advanced propulsion techniques must be considered if the currently envisioned launch date of the manned Mars mission were delayed until 2020 or later. Within the next thirty years, technological advances may allow such methods as beaming power to the ship, inertial-confinement fusion, or mass-conversion of antiprotons to become feasible. A propulsion system with an ISP of around 5000 s would allow the currently envisioned mission module to fly to Mars in 3 months and would require about one million pounds to be assembled in Earth orbit. Of the possible methods to achieve this, the antiproton mass-conversion reaction offers the highest potential, the greatest problems, and the most fascination. Increasing the production rates of antiprotons is a high priority task at facilities around the world. The application of antiprotons to propulsion requires the coupling of the energy released in the mass-conversion reaction to thrust-producing mechanisms. Recent proposals entail using the antiprotons to produce inertial confinement fusion or to produce negative muons which can catalyze fusion. By increasing the energy released per antiproton, the effective cost, (dollars/joule) can be reduced. These proposals and other areas of research can be investigated now. These short term results will be important in assessing the long range feasibility of an antiproton powered engine.

Bacterial production and their role in the removal of dissolved organic matter from tributaries of drinking water reservoirs.

PubMed

Kamjunke, Norbert; Oosterwoud, Marieke R; Herzsprung, Peter; Tittel, Jörg

2016-04-01

Enhanced concentrations of dissolved organic matter (DOM) in freshwaters are an increasing problem in drinking water reservoirs. In this study we investigated bacterial DOM degradation rates in the tributaries of the reservoirs and tested the hypotheses that (1) DOM degradation is high enough to decrease DOM loads to reservoirs considerably, (2) DOM degradation is affected by stream hydrology, and (3) phosphorus addition may stimulate bacterial DOM degradation. Bacterial biomass production, which was used as a measure of DOM degradation, was highest in summer, and was usually lower at upstream than at downstream sites. An important proportion of bacterial production was realized in epilithic biofilms. Production of planktonic and biofilm bacteria was related to water temperature. Planktonic production weakly correlated to DOM quality and to total phosphorus concentration. Addition of soluble reactive phosphorus did not stimulate bacterial DOM degradation. Overall, DOM was considerably degraded in summer at low discharge levels, whereas degradation was negligible during flood events (when DOM load in reservoirs was high). The ratio of DOM degradation to total DOM release was negatively related to discharge. On annual average, only 0.6-12% of total DOM released by the catchments was degraded within the tributaries. Copyright © 2016 Elsevier B.V. All rights reserved.

[Physicopharmaceutical characteristics of ulinastatin vaginal suppositories prepared in a hospital].

PubMed

Satake, Kiyoshi; Nakajima, Takanori; Iwata, Masanori; Fujikake, Yoshio; Kimura, Masayuki

2011-01-01

We studied a locally applied vaginal preparation (vaginal suppositories) of ulinastatin (urinary trypsin inhibitor, UTI), designed to threatened premature delivery and maintain pregnancy. Witepsol S55 was chosen as the basic component of the vaginal suppositories based on the physical pharmaceutical characteristics of three kinds of hard fats. The average particle size of the UTI aqueous injection was approximately 70% as compared with that of the UTI lyophilized product, used as the base material for the preparation of UTI vaginal suppositories. We compared the physical pharmaceutical properties of UTI vaginal suppositories with water contents of 2.5%, 5.0%, and 7.5%, respectively. Preparation strength negatively correlated with the water content. The coefficient of viscosity positively correlated with the water content of the preparation. UTI vaginal suppositories with a water content of 5.0% had the highest average drug release rate on moment analysis. A comprehensive evaluation of the properties of UTI vaginal suppositories, including high strength due to disintegration resistance, the coefficient of viscosity and its influence on local retention, and drug release and its influence on the duration of effect, indicated that a 5.0% UTI aqueous solution for injection combined with Witepsol S55 as the base was the optimal formulation for the hospital preparation of vaginal suppositories.

Increased nitrous oxide emissions from Arctic peatlands after permafrost thaw

PubMed Central

Marushchak, Maija E.; Lamprecht, Richard E.; Jackowicz-Korczyński, Marcin; Lindgren, Amelie; Mastepanov, Mikhail; Granlund, Lars; Christensen, Torben R.; Tahvanainen, Teemu; Martikainen, Pertti J.; Biasi, Christina

2017-01-01

Permafrost in the Arctic is thawing, exposing large carbon and nitrogen stocks for decomposition. Gaseous carbon release from Arctic soils due to permafrost thawing is known to be substantial, but growing evidence suggests that Arctic soils may also be relevant sources of nitrous oxide (N2O). Here we show that N2O emissions from subarctic peatlands increase as the permafrost thaws. In our study, the highest postthaw emissions occurred from bare peat surfaces, a typical landform in permafrost peatlands, where permafrost thaw caused a fivefold increase in emissions (0.56 ± 0.11 vs. 2.81 ± 0.6 mg N2O m−2 d−1). These emission rates match those from tropical forest soils, the world’s largest natural terrestrial N2O source. The presence of vegetation, known to limit N2O emissions in tundra, did decrease (by ∼90%) but did not prevent thaw-induced N2O release, whereas waterlogged conditions suppressed the emissions. We show that regions with high probability for N2O emissions cover one-fourth of the Arctic. Our results imply that the Arctic N2O budget will depend strongly on moisture changes, and that a gradual deepening of the active layer will create a strong noncarbon climate change feedback. PMID:28559346

Worldwide prevalence and incidence of osteoporotic vertebral fractures.

PubMed

Ballane, G; Cauley, J A; Luckey, M M; El-Hajj Fuleihan, G

2017-05-01

We investigated the prevalence and incidence of vertebral fractures worldwide. We used a systematic Medline search current to 2015 and updated as per authors' libraries. A total of 62 articles of fair to good quality and comparable methods for vertebral fracture identification were considered. The prevalence of morphometric vertebral fractures in European women is highest in Scandinavia (26%) and lowest in Eastern Europe (18%). Prevalence rates in North America (NA) for White women ≥50 are 20-24%, with a White/Black ratio of 1.6. Rates in women ≥50 years in Latin America are overall lower than Europe and NA (11-19%). In Asia, rates in women above ≥65 are highest in Japan (24%), lowest in Indonesia (9%), and in the Middle East, Lebanon, rates are 20%. The highest-lowest ratio between countries, within and across continents, varied from 1.4-2.6. Incidence data is less abundant and more heterogeneous. Age-standardized rates in studies combining hospitalized and ambulatory vertebral fractures are highest in South Korea, USA, and Hong Kong and lowest in the UK. Neither a North-South gradient nor a relation to urbanization is evident. Conversely, the incidence of hospitalized vertebral fractures in European patients ≥50 shows a North-South gradient with 3-3.7-fold variability. In the USA, rates in Whites are approximately 4-fold higher than in Blacks. Vertebral fractures variation worldwide is lower than observed with hip fractures, and some of highest rates are unexpectedly from Asia. Better quality representative studies are needed. We investigate the occurrence of vertebral fractures, worldwide, using published data current until the present. Worldwide, the variation in vertebral fractures is lower than observed for hip fractures. Some of the highest rates are from North America and unexpectedly Asia. The highest-lowest ratio between countries, within and across continents, varied from 1.4-2.6. Better quality representative data is needed.

Ethnic and Racial Inequalities in Notified Cases of Tuberculosis in Brazil

PubMed Central

Viana, Paulo Victor de Sousa; Gonçalves, Maria Jacirema Ferreira; Basta, Paulo Cesar

2016-01-01

Objective This study analysed clinical and sociodemographic aspects and follow-up for notified cases of tuberculosis (TB) and explored inequalities in incidence rates and outcome by colour or race and the geographic macro-regions of Brazil. Methods This paper reports the results of a population-based descriptive epidemiological study of all notified cases of TB in Brazil during the period from 01/01/2008 to 31/12/2011. We analysed sociodemographic and clinical variables according to colour or race (white, black, Asian, mixed, and indigenous) and geographic macro-regions of the country (North, Northeast, Central-West, South, and Southeast). Results During the study period, the average incidence of TB in Brazil was 36.7 cases per 100,000 inhabitants, with the highest rates occurring in the North and Southeast regions. The analysis of TB notifications by colour or race revealed that the indigenous population presented the highest incidence rates in all macro-regions except the South, where higher rates were reported in black patients. ‘Cured’ was the most frequently reported treatment outcome for all skin colour categories. The highest cure rate occurred among the indigenous population (76.8%), while the lowest cure rate occurred among the black population (70.7%). Rates of treatment default were highest among blacks (10.5%) and lowest among the indigenous population (6.9%). However, the fatality rate was similar across race categories, varying between 2.8% and 3.8% for whites and the indigenous population, respectively. The lowest cure rates were observed when follow-up was inadequate (58.3%), and the highest was observed when the follow-up was classified as excellent (96.8%). Conclusions This study revealed that—apart from the heterogeneous distribution of TB among the Brazilian macro-regions—ethnic-racial inequalities exist in terms of clinical-epidemiological characteristics and incidence rates as well as follow-up for cases undergoing treatment. The highest rates of TB occurred among the indigenous people. PMID:27176911

International trends in liver cancer incidence, overall and by histologic subtype, 1978-2007.

PubMed

Petrick, Jessica L; Braunlin, Megan; Laversanne, Mathieu; Valery, Patricia C; Bray, Freddie; McGlynn, Katherine A

2016-10-01

Primary liver cancer, the most common histologic types of which are hepatocellular carcinoma (HCC) and intrahepatic cholangiocarcinoma (ICC), is the second leading cause of cancer death worldwide. While rising incidence of liver cancer in low-risk areas and decreasing incidence in some high-risk areas has been reported, trends have not been thoroughly explored by country or by histologic type. We examined liver cancer incidence overall and by histology by calendar time and birth cohort for selected countries between 1978 and 2007. For each successive 5-year period, age-standardized incidence rates were calculated from volumes V-IX of the Cancer Incidence in Five Continents electronic database (CI5plus) and the newly released CI5X (volume X) database. Wide global variations persist in liver cancer incidence. Rates of liver cancer remain highest in Asian countries, specifically Eastern and South-Eastern Asian countries. While rates in most of these high-risk countries have been decreasing in recent years, rates in India and several low-risk countries of Africa, Europe, the Americas, and Oceania have been on the rise. Liver cancer rates by histologic type tend to convey a similar temporal profile. However, in Thailand, France, and Italy, ICC rates have increased while HCC rates have declined. We expect rates in high-risk countries to continue to decrease, as the population seroprevalence of hepatitis B virus (HBV) continues to decline. In low-risk countries, targeted screening and treatment of the hepatitis C virus (HCV), treatment of diabetes and primary prevention of obesity, will be key in reducing future liver cancer incidence. © 2016 UICC.

Forest soil mineral weathering rates: use of multiple approaches

Treesearch

Randy K. Kolka; D.F. Grigal; E.A. Nater

1996-01-01

Knowledge of rates of release of base cations from mineral dissolution (weathering) is essential to understand ecosystem elemental cycling. Although much studied, rates remain enigmatic. We compared the results of four methods to determine cation (Ca + Mg + K) release rates at five forested soils/sites in the northcentral U.S.A. Our premise was that multiple...

Induced abortion in Italy: levels, trends and characteristics.

PubMed

Bettarini, S S; D'Andrea, S S

1996-01-01

Subsequent to the legalization of abortion in Italy in 1978, abortion; rates among Italian women first rose and then declined steadily, from a peak of 16.9 abortions per 1,000 women of reproductive age in 1983 to 9.8 per 1,000 in 1993. Abortion rates vary considerably by geographic region, with rates typically highest in the more secular and modernized regions and lowest in regions where traditional values predominate. Data from 1981 and 1991 indicate that age-specific abortion rates decreased during the 1980s for all age-groups, with the largest declines occurring in regions with the highest levels of abortion. Moreover, a shift in the age distribution of abortion rates occurred during the 1980s, with women aged 30-34 registering the highest abortion rate in 1991, whereas in 1981 the highest level of abortion occurred among those aged 25-29. The abortion rate among adolescent women was low at both times (7.6 per 1,000 in 1981 and 4.6 per 1,000 in 1991). These data are based only on reported legal abortions; the number of clandestine abortions remains unknown.

The association between male-biased sex ratio and indicators of stress in red-spotted newts.

PubMed

Aspbury, Andrea S; Grayson, Kristine L; Fantaye, Selamawit; Nichols, Ian; Myers-Burton, Miranda; Ortiz-Mangual, Xavier; Gabor, Caitlin R

2017-05-01

In populations with a male-biased operational sex ratio, coercive mating by males can have fitness consequences for females. One component of reduced fitness for females in populations with a male-biased OSR may be greater activation of the stress response, resulting in higher corticosterone release rates (CORT; a glucocorticoid stress hormone in amphibians). We test the hypothesis that a male-biased sex ratio affects female activity and release rates of CORT and testosterone (T) in male and female red-spotted newts (Notophthalmus viridescens). First, we evaluated if chemical cues from a male-biased sex ratio affect activity and CORT release rates in females. We predicted that females exposed to chemical cues of three males would be less active and have higher CORT release rates than those exposed to chemical cues of one male. Second, we measured CORT release rates of red-spotted newts in field enclosures with either a male-biased or a female-biased sex ratio. We predicted that females in the male-biased treatment would have higher CORT and T release rates than those in a female-biased treatment, owing to higher levels of male harassment. We also predicted that males would have higher CORT and T release rates in male-biased treatments due to higher levels of male-male competition. Females were not less active in response to chemical cues from more males over fewer males, but there was a positive relationship between female activity and CORT when they were exposed to the cues of three males. We also found that females, but not males, in the male-biased sex ratio treatment had higher CORT and T release rates than those in the female-biased treatment. Our results support the hypothesis that a male-biased sex ratio leads to a higher stress response, which may underlie the observed decrease in immune function and body condition in previous work exposing female red-spotted newts to a male-biased sex ratio. This study furthers our understanding of the mechanistic basis for costs associated with a male-biased sex ratio in a pond-breeding amphibian. Copyright © 2017 Elsevier Inc. All rights reserved.

Metal release from coffee machines and electric kettles.

PubMed

Müller, Frederic D; Hackethal, Christin; Schmidt, Roman; Kappenstein, Oliver; Pfaff, Karla; Luch, Andreas

2015-01-01

The release of elemental ions from 8 coffee machines and 11 electric kettles into food simulants was investigated. Three different types of coffee machines were tested: portafilter espresso machines, pod machines and capsule machines. All machines were tested subsequently on 3 days before and on 3 days after decalcification. Decalcification of the machines was performed with agents according to procedures as specified in the respective manufacturer's manuals. The electric kettles showed only a low release of the elements analysed. For the coffee machines decreasing concentrations of elements were found from the first to the last sample taken in the course of 1 day. Metal release on consecutive days showed a decreasing trend as well. After decalcification a large increase in the amounts of elements released was encountered. In addition, the different machine types investigated clearly differed in their extent of element release. By far the highest leaching, both quantitatively and qualitatively, was found for the portafilter machines. With these products releases of Pb, Ni, Mn, Cr and Zn were in the range and beyond the release limits as proposed by the Council of Europe. Therefore, a careful rinsing routine, especially after decalcification, is recommended for these machines. The comparably lower extent of release of one particular portafilter machine demonstrates that metal release at levels above the threshold that triggers health concerns are technically avoidable.

On use of CO{sub 2} chemiluminescence for combustion metrics in natural gas fired reciprocating engines.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gupta, S. B.; Bihari, B.; Biruduganti, M.

Flame chemiluminescence is widely acknowledged to be an indicator of heat release rate in premixed turbulent flames that are representative of gas turbine combustion. Though heat release rate is an important metric for evaluating combustion strategies in reciprocating engine systems, its correlation with flame chemiluminescence is not well studied. To address this gap an experimental study was carried out in a single-cylinder natural gas fired reciprocating engine that could simulate turbocharged conditions with exhaust gas recirculation. Crank angle resolved spectra (266-795 nm) of flame luminosity were measured for various operational conditions by varying the ignition timing for MBT conditions andmore » by holding the speed at 1800 rpm and Brake Mean effective Pressure (BMEP) at 12 bar. The effect of dilution on CO*{sub 2}chemiluminescence intensities was studied, by varying the global equivalence ratio (0.6-1.0) and by varying the exhaust gas recirculation rate. It was attempted to relate the measured chemiluminescence intensities to thermodynamic metrics of importance to engine research -- in-cylinder bulk gas temperature and heat release rate (HRR) calculated from measured cylinder pressure signals. The peak of the measured CO*{sub 2} chemiluminescence intensities coincided with peak pressures within {+-}2 CAD for all test conditions. For each combustion cycle, the peaks of heat release rate, spectral intensity and temperature occurred in that sequence, well separated temporally. The peak heat release rates preceded the peak chemiluminescent emissions by 3.8-9.5 CAD, whereas the peak temperatures trailed by 5.8-15.6 CAD. Such a temporal separation precludes correlations on a crank-angle resolved basis. However, the peak cycle heat release rates and to a lesser extent the peak cycle temperatures correlated well with the chemiluminescent emission from CO*{sub 2}. Such observations point towards the potential use of flame chemiluminescence to monitor peak bulk gas temperatures as well as peak heat release rates in natural gas fired reciprocating engines.« less

Martian Multimedia: The Agony and Ecstasy of Communicating Real-Time, Authentic Science During the Phoenix Mars Mission

NASA Astrophysics Data System (ADS)

Bitter, C.; Buxner, S. R.

2009-03-01

The Phoenix Mars Mission faced robust communication challenges requiring real-time solutions. Managing the message from Mars and ensuring the highest quality of science data and news releases were our top priorities during mission surface operations.

30 CFR 7.502 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the combined effects of air movement, heat, and humidity on the human body. Breathable oxygen. Oxygen.... Noncombustible material. Material, such as concrete or steel, that will not ignite, burn, support combustion, or release flammable vapors when subjected to fire or heat. Overpressure. The highest pressure over the...

30 CFR 7.502 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the combined effects of air movement, heat, and humidity on the human body. Breathable oxygen. Oxygen.... Noncombustible material. Material, such as concrete or steel, that will not ignite, burn, support combustion, or release flammable vapors when subjected to fire or heat. Overpressure. The highest pressure over the...

30 CFR 7.502 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the combined effects of air movement, heat, and humidity on the human body. Breathable oxygen. Oxygen.... Noncombustible material. Material, such as concrete or steel, that will not ignite, burn, support combustion, or release flammable vapors when subjected to fire or heat. Overpressure. The highest pressure over the...

30 CFR 7.502 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the combined effects of air movement, heat, and humidity on the human body. Breathable oxygen. Oxygen.... Noncombustible material. Material, such as concrete or steel, that will not ignite, burn, support combustion, or release flammable vapors when subjected to fire or heat. Overpressure. The highest pressure over the...

30 CFR 7.502 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the combined effects of air movement, heat, and humidity on the human body. Breathable oxygen. Oxygen.... Noncombustible material. Material, such as concrete or steel, that will not ignite, burn, support combustion, or release flammable vapors when subjected to fire or heat. Overpressure. The highest pressure over the...

Detection and Evaluation of Elevated Lead Release from Service Lines: A Field Study

EPA Science Inventory

Comparative stagnation sampling conducted in 32 homes in Chicago, Illinois with lead service (LSLs) demonstrated that the existing regulatory sampling protocol under the U. S. Lead and Copper Rule (LCR) systematically underestimated lead corrosion. Lead levels were highest within...

Composite poly(vinyl alcohol)/poly(vinyl acetate) electrospun nanofibrous mats as a novel wound dressing matrix for controlled release of drugs

PubMed Central

Jannesari, Marziyeh; Varshosaz, Jaleh; Morshed, Mohammad; Zamani, Maedeh

2011-01-01

The aim of this study was to develop novel biomedicated nanofiber electrospun mats for controlled drug release, especially drug release directly to an injury site to accelerate wound healing. Nanofibers of poly(vinyl alcohol) (PVA), poly(vinyl acetate) (PVAc), and a 50:50 composite blend, loaded with ciprofloxacin HCl (CipHCl), were successfully prepared by an electrospinning technique for the first time. The morphology and average diameter of the electrospun nanofibers were investigated by scanning electron microscopy. X-ray diffraction studies indicated an amorphous distribution of the drug inside the nanofiber blend. Introducing the drug into polymeric solutions significantly decreased solution viscosities as well as nanofiber diameter. In vitro drug release evaluations showed that both the kind of polymer and the amount of drug loaded greatly affected the degree of swelling, weight loss, and initial burst and rate of drug release. Blending PVA and PVAc exhibited a useful and convenient method for electrospinning in order to control the rate and period of drug release in wound healing applications. Also, the thickness of the blend nanofiber mats strongly influenced the initial release and rate of drug release. PMID:21720511

[Carcinogenic N-nitrosamines in the tire industry].

PubMed

Sokol?kaia, N N; Krivosheeva, L V; Khesing, A Ia; Piven, V A; Kavun, S M

1993-01-01

The level of volatile carcinogenic N-nitrosamines (NA) was studied in the air of various technological sites of tyre production. Reported total levels of NA in air exceeded MACs set in certain countries for the same enterprises. For example, German total MAC for 12 carcinogenic NA is 1 g/m3. N-nitrosomorpholine appeared to have the highest level (91 g/m3), probably, because its derivatives are used as raw material for technological process. Relative rate of volatile NA release from rubber samples containing 4-nitrosodiphenylamine (modifier) was studied. The parameter was reported to have no influence on NA outlet in conditions simulating technological process. NA was detected by means of gas chromatography with thermal energy detector TEA 502A provided by Thermo Electron Corporation, USA. The article necessitates regulation of NA in tyre production and better rubber mixtures to control the pollution of atmosphere.

Optimization of Dissolution Compartments in a Biorelevant Dissolution Apparatus Golem v2, Supported by Multivariate Analysis.

PubMed

Stupák, Ivan; Pavloková, Sylvie; Vysloužil, Jakub; Dohnal, Jiří; Čulen, Martin

2017-11-23

Biorelevant dissolution instruments represent an important tool for pharmaceutical research and development. These instruments are designed to simulate the dissolution of drug formulations in conditions most closely mimicking the gastrointestinal tract. In this work, we focused on the optimization of dissolution compartments/vessels for an updated version of the biorelevant dissolution apparatus-Golem v2. We designed eight compartments of uniform size but different inner geometry. The dissolution performance of the compartments was tested using immediate release caffeine tablets and evaluated by standard statistical methods and principal component analysis. Based on two phases of dissolution testing (using 250 and 100 mL of dissolution medium), we selected two compartment types yielding the highest measurement reproducibility. We also confirmed a statistically ssignificant effect of agitation rate and dissolution volume on the extent of drug dissolved and measurement reproducibility.

Oral Disintegration Tablets of Stavudine for HIV Management: A New Technological Approach

PubMed Central

Sankar, V.; Ramakrishna, B.; Devi, P. Shalini; Karthik, S.

2012-01-01

Stavudine oral disintegration tablets were formulated to minimize the bitter taste and to reduce the first-pass hepatic metabolism. The various precompression parameters like the angle of repose, bulk density, compressibility index and Hausner's ratio were determined for the powder blend. In this study, 14 formulations of stavudine oral disintegration tablet were prepared by direct compression method. The tablets were evaluated for weight variation, percentage friability, disintegration time, hardness, wetting time and water absorption ratio. The in vitro dissolution study results of the batch S1 (stavudine+crospovidone+sodium starch glycollate) are encouraging as highest dissolution rate (99.2% in 100 min) and lowest time of disintegration (56 s) was achieved. The in vivo drug release studies were carried out in rabbits and the relative bioavailability of formulation S1 was found to be 2.83 times greater than that of conventional tablets. PMID:23798782

Assessing geomorphic change along the Trinity River downstream from Lewiston Dam, California, 1980-2011

USGS Publications Warehouse

Curtis, Jennifer A.; Wright, Scott A.; Minear, Justin T.; Flint, Lorraine E.

2015-01-01

The highest rates of change in the areal extents of channel and riparian features were observed during the pre‑2001 period, which was longer and relatively wetter than the post-2001 period. A series of tributary floods in 1997, 1998, and 2006 increased channel complexity and floodplain connectivity. During the post-2006 period, managed-flow releases, in the absence of tributary flooding, combined with gravel augmentation and mechanical restoration, caused localized increases in sediment supply and transport capacity that led to smaller, but measurable, increases in channel complexity and floodplain connectivity in the upper river near Lewiston Dam. Extensive pre-2001 channel widening and the muted geomorphic response of channel rehabilitation sites to post-2001 managed flows highlight the need for continued monitoring and assessment of the magnitude, duration, and timing of prescriptive flows and associated geomorphic responses.

Oral Disintegration Tablets of Stavudine for HIV Management: A New Technological Approach.

PubMed

Sankar, V; Ramakrishna, B; Devi, P Shalini; Karthik, S

2012-11-01

Stavudine oral disintegration tablets were formulated to minimize the bitter taste and to reduce the first-pass hepatic metabolism. The various precompression parameters like the angle of repose, bulk density, compressibility index and Hausner's ratio were determined for the powder blend. In this study, 14 formulations of stavudine oral disintegration tablet were prepared by direct compression method. The tablets were evaluated for weight variation, percentage friability, disintegration time, hardness, wetting time and water absorption ratio. The in vitro dissolution study results of the batch S1 (stavudine+crospovidone+sodium starch glycollate) are encouraging as highest dissolution rate (99.2% in 100 min) and lowest time of disintegration (56 s) was achieved. The in vivo drug release studies were carried out in rabbits and the relative bioavailability of formulation S1 was found to be 2.83 times greater than that of conventional tablets.

Measurement of vertical stability metrics in KSTAR

NASA Astrophysics Data System (ADS)

Hahn, Sang-Hee; Humphreys, D. A.; Mueller, D.; Bak, J. G.; Eidietis, N. W.; Kim, H.-S.; Ko, J. S.; Walker, M. L.; Kstar Team

2017-10-01

The paper summarizes results of multi-year ITPA experiments regarding measurement of the vertical stabilization capability of KSTAR discharges, including most recent measurements at the highest achievable elongation (κ 2.0 - 2.1). The measurements of the open-loop growth rate of VDE (γz) and the maximum controllable vertical displacement (ΔZmax) are done by the release-and-catch method. The dynamics of the vertical movement of the plasma is verified by both relevant magnetic reconstructions and non-magnetic diagnostics. The measurements of γz and ΔZmax were done for different plasma currents, βp, internal inductances, elongations and different configurations of the vessel conductors that surround the plasma as the first wall. Effects of control design choice and diagnostics noise are discussed, and comparison with the axisymmetric plasma response model is given for partial accounting for the measured control capability. This work supported by Ministry of Science, ICT, and Future Planning under KSTAR project.

Increasing resistant coagulase negative staphylococci in bovine clinical mastitis.

PubMed

Moniri, R; Dastehgoli, K; Akramian, A

2007-08-01

The aim of this study was to determine Coagulase Negative Staphylococci (CNS) and other bacteria for their resistance to antimicrobial agents approved for the control of pathogens involved in clinical bovine mastitis. This descriptive study was done on 106 milk samples obtained from clinical mastitis in dairy cattle husbandry from April 2006 through August 2006 in Kashan, Iran. From the total of 106 milk samples collected from clinical mastitis, 96 (90.6%) lead to positive culture. Coagulase negative Staphylococci isolated in 51 out of 96 samples (53.1%), Staphylococcus aureus isolated in 21 out of 96 (21.9%), gram negative bacilli isolated in 14 out of 96 (14.6%) and Enterococci isolated in 4 (4.2%). The highest rate of resistant CNS observed to penicillin (56.6%) and the highest rate of sensitivity to enrofloxacin 100%, followed by kanamycin, streptomycin and neomycin, 92.2, 82.3 and 82.3%, respectively. The highest rate of resistance S. aureus exhibited to penicillin (66.6%); while the highest rate of sensitivity showed to trimethoprim-sulphamethoxasole (81%), followed by kanamycin and enrofloxacin both at 76.2%. The highest rate of resistance gram negative bacilli exhibited to ampicillin and erythromycin at 71.4%. Their highest rate of sensitivity observed to enrofloxacin (78.6%), followed by kanamycin, (71.4%). In recent years, CNS is emerging as important minor mastitis pathogens and can be the cause of substantial economic losses. The high resistance rate to penicillin and other antibiotics found in this study emphasize the importance of identification of CNS when a bovine clinical mastitis is present.

Study of the influence of fuel load and slope on a fire spreading across a bed of pine needles by using oxygen consumption calorimetry

NASA Astrophysics Data System (ADS)

Tihay, V.; Morandini, F.; Santoni, P. A.; Perez-Ramirez, Y.; Barboni, T.

2012-11-01

A set of experiments using a Large Scale Heat Release Rate Calorimeter was conducted to test the effects of slope and fuel load on the fire dynamics. Different parameters such as the geometry of the flame front, the rate of spread, the mass loss rate and the heat release rate were investigated. Increasing the fuel load or the slope modifies the fire behaviour. As expected, the flame length and the rate of spread increase when fuel load or slope increases. The heat release rate does not reach a quasi-steady state when the propagation takes place with a slope of 20° and a high fuel load. This is due to an increase of the length of the fire front leading to an increase of fuel consumed. These considerations have shown that the heat release can be estimated with the mass loss rate by considering the effective heat of combustion. This approach can be a good alternative to estimate accurately the fireline intensity when the measure of oxygen consumption is not possible.

Sustained Release Drug Delivery Applications of Polyurethanes.

PubMed

Lowinger, Michael B; Barrett, Stephanie E; Zhang, Feng; Williams, Robert O

2018-05-09

Since their introduction over 50 years ago, polyurethanes have been applied to nearly every industry. This review describes applications of polyurethanes to the development of modified release drug delivery. Although drug delivery research leveraging polyurethanes has been ongoing for decades, there has been renewed and substantial interest in the field in recent years. The chemistry of polyurethanes and the mechanisms of drug release from sustained release dosage forms are briefly reviewed. Studies to assess the impact of intrinsic drug properties on release from polyurethane-based formulations are considered. The impact of hydrophilic water swelling polyurethanes on drug diffusivity and release rate is discussed. The role of pore formers in modulating drug release rate is examined. Finally, the value of assessing mechanical properties of the dosage form and approaches taken in the literature are described.

Floating tablets for controlled release of ofloxacin via compression coating of hydroxypropyl cellulose combined with effervescent agent.

PubMed

Qi, Xiaole; Chen, Haiyan; Rui, Yao; Yang, Fengjiao; Ma, Ning; Wu, Zhenghong

2015-07-15

To prolong the residence time of dosage forms within gastrointestinal trace until all drug released at desired rate was one of the real challenges for oral controlled-release drug delivery system. Herein, we developed a fine floating tablet via compression coating of hydrophilic polymer (hydroxypropyl cellulose) combined with effervescent agent (sodium bicarbonate) to achieve simultaneous control of release rate and location of ofloxacin. Sodium alginate was also added in the coating layer to regulate the drug release rate. The effects of the weight ratio of drug and the viscosity of HPC on the release profile were investigated. The optimized formulations were found to immediately float within 30s and remain lastingly buoyant over a period of 12 h in simulated gastric fluid (SGF, pH 1.2) without pepsin, indicating a satisfactory floating and zero-order drug release profile. In addition, the oral bioavailability experiment in New Zealand rabbits showed that, the relative bioavailability of the ofloxacin after administrated of floating tablets was 172.19%, compared to marketed common release tablets TaiLiBiTuo(®). These results demonstrated that those controlled-released floating tables would be a promising gastro-retentive delivery system for drugs acting in stomach. Copyright © 2015 Elsevier B.V. All rights reserved.

Release of feruloylated oligosaccharides from wheat bran through submerged fermentation by edible mushrooms.

PubMed

Xie, Chunyan; Wu, Zhiyan; Guo, Hongzhen; Gu, Zhenxin

2014-07-01

Wheat bran, a by-product of the flour industry, is believed to be a raw material for the production of feruloylated oligosaccharides (FOs) because of its high content of conjiont ferulic acid (FA). Studies were carried out to identify edible mushrooms that are able to release FOs from wheat bran. All the six tested mushrooms (Pleurotus ostreatus, Hericium erinaceum, Auricularia auricula, Cordyceps militaris, Agrocybe chaxingu, and Ganoderma lucium) were found to release FOs, and Agrocybe chaxingu had the highest yield, reaching 35.4 µM in wheat bran broth. Enzymes detection showed that these species secreted extracellular enzymes during fermentation, including cellulase and xylanase. Agrocybe chaxingu secreted the significant amount of xylanase (180 mU ml(-1) ), which was responsible for the release of FOs from wheat bran, while Hericium erinaceum secreted FA esterase which could disassemble FOs. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Smart release of doxorubicin loaded on polyetheretherketone (PEEK) surface with 3D porous structure.

PubMed

Ouyang, Liping; Sun, Zhenjie; Wang, Donghui; Qiao, Yuqin; Zhu, Hongqin; Ma, Xiaohan; Liu, Xuanyong

2018-03-01

It is important to fabricate an implant possessing environment sensitive drug delivery. In this work, the construction of 3D porous structure on polyetheretherketone (PEEK) surface and pH sensitive polymer, chitosan, was introduced. The smart release of doxorubicin can be realized on the 3D porous surface of PEEK loading chitosan. We give a feasible explanation for the effect of chitosan on smart drug release according to Henderson-Hasselbalch equation. Furthermore, the intracellular drug content of the cell cultured on the samples with highest chitosan is significantly higher at pH 4.0, whereas lower at pH 7.4 than other samples. The smart release of doxorubicin via modification with chitosan onto 3D porous PEEK surface paves the way for the application of PEEK in drug loading platform for recovering bone defect caused by malignant bone tumor. Copyright © 2017 Elsevier B.V. All rights reserved.