Harmonic analysis of electrified railway based on improved HHT

NASA Astrophysics Data System (ADS)

Wang, Feng

2018-04-01

In this paper, the causes and harms of the current electric locomotive electrical system harmonics are firstly studied and analyzed. Based on the characteristics of the harmonics in the electrical system, the Hilbert-Huang transform method is introduced. Based on the in-depth analysis of the empirical mode decomposition method and the Hilbert transform method, the reasons and solutions to the endpoint effect and modal aliasing problem in the HHT method are explored. For the endpoint effect of HHT, this paper uses point-symmetric extension method to extend the collected data; In allusion to the modal aliasing problem, this paper uses the high frequency harmonic assistant method to preprocess the signal and gives the empirical formula of high frequency auxiliary harmonic. Finally, combining the suppression of HHT endpoint effect and modal aliasing problem, an improved HHT method is proposed and simulated by matlab. The simulation results show that the improved HHT is effective for the electric locomotive power supply system.

Estimating regression to the mean and true effects of an intervention in a four-wave panel study.

PubMed

Gmel, Gerhard; Wicki, Matthias; Rehm, Jürgen; Heeb, Jean-Luc

2008-01-01

First, to analyse whether a taxation-related decrease in spirit prices had a similar effect on spirit consumption for low-, medium- and high-level drinkers. Secondly, as the relationship between baseline values and post-intervention changes is confounded with regression to the mean (RTM) effects, to apply different approaches for estimating the RTM effect and true change. Consumption of spirits and total alcohol consumption were analysed in a four-wave panel study (one pre-intervention and three post-intervention measurements) of 889 alcohol consumers sampled from the general population of Switzerland. Two correlational methods, one method quantitatively estimating the RTM effect and one growth curve approach based on hierarchical linear models (HLM), were used to estimate RTM effects among low-, medium- and high-level drinkers. Adjusted for RTM effects, high-level drinkers increased consumption more than lighter drinkers in the short term, but this was not a persisting effect. Changes in taxation affected mainly light and moderate drinkers in the long term. All methods concurred that RTM effects were present to a considerable degree, and methods quantifying the RTM effect or adjusting for it yielded similar estimates. Intervention studies have to consider RTM effects both in the study design and in the evaluation methods. Observed changes can be adjusted for RTM effects and true change can be estimated. The recommended method, particularly if the aim is to estimate change not only for the sample as a whole, but for groups of drinkers with different baseline consumption levels, is growth curve modelling. If reliability of measurement instruments cannot be increased, the incorporation of more than one pre-intervention measurement point may be a valuable adjustment of the study design.

Rosenberg's Self-Esteem Scale: Two Factors or Method Effects.

ERIC Educational Resources Information Center

Tomas, Jose M.; Oliver, Amparo

1999-01-01

Results of a study with 640 Spanish high school students suggest the existence of a global self-esteem factor underlying responses to Rosenberg's (M. Rosenberg, 1965) Self-Esteem Scale, although the inclusion of method effects is needed to achieve a good model fit. Method effects are associated with item wording. (SLD)

Needs of the Learning Effect on Instructional Website for Vocational High School Students

ERIC Educational Resources Information Center

Lo, Hung-Jen; Fu, Gwo-Liang; Chuang, Kuei-Chih

2013-01-01

The purpose of study was to understand the correlation between the needs of the learning effect on instructional website for the vocational high school students. Our research applied the statistic methods of product-moment correlation, stepwise regression, and structural equation method to analyze the questionnaire with the sample size of 377…

Herpin effective media resonant underlayers and resonant overlayer designs for ultra-high NA interference lithography.

PubMed

Bourke, Levi; Blaikie, Richard J

2017-12-01

Dielectric waveguide resonant underlayers are employed in ultra-high NA interference photolithography to effectively double the depth of field. Generally a single high refractive index waveguiding layer is employed. Here multilayer Herpin effective medium methods are explored to develop equivalent multilayer waveguiding layers. Herpin equivalent resonant underlayers are shown to be suitable replacements provided at least one layer within the Herpin trilayer supports propagating fields. In addition, a method of increasing the intensity incident upon the photoresist using resonant overlayers is also developed. This method is shown to greatly enhance the intensity within the photoresist making the use of thicker, safer, non-absorbing, low refractive index matching liquids potentially suitable for large-scale applications.

Optimization of air gap for two-dimensional imaging system using synchrotron radiation

NASA Astrophysics Data System (ADS)

Zeniya, Tsutomu; Takeda, Tohoru; Yu, Quanwen; Hyodo, Kazuyuki; Yuasa, Tetsuya; Aiyoshi, Yuji; Hiranaka, Yukio; Itai, Yuji; Akatsuka, Takao

2000-11-01

Since synchrotron radiation (SR) has several excellent properties such as high brilliance, broad continuous energy spectrum and small divergence, we can obtain x-ray images with high contrast and high spatial resolution by using of SR. In 2D imaging using SR, air gap method is very effective to reduce the scatter contamination. However, to use air gap method, the geometrical effect of finite source size of SR must be considered because spatial resolution of image is degraded by air gap. For 2D x-ray imaging with SR, x-ray mammography was chosen to examine the effect of air gap method. We theoretically discussed the optimization of air gap distance suing effective scatter point source model proposed by Muntz, and executed experiment with a newly manufactured monochromator with asymmetrical reflection and an imaging plate.

Clouds in the atmospheres of extrasolar planets. IV. On the scattering greenhouse effect of CO2 ice particles: Numerical radiative transfer studies

NASA Astrophysics Data System (ADS)

Kitzmann, D.; Patzer, A. B. C.; Rauer, H.

2013-09-01

Context. Owing to their wavelength-dependent absorption and scattering properties, clouds have a strong impact on the climate of planetary atmospheres. The potential greenhouse effect of CO2 ice clouds in the atmospheres of terrestrial extrasolar planets is of particular interest because it might influence the position and thus the extension of the outer boundary of the classic habitable zone around main sequence stars. Such a greenhouse effect, however, is a complicated function of the CO2 ice particles' optical properties. Aims: We study the radiative effects of CO2 ice particles obtained by different numerical treatments to solve the radiative transfer equation. To determine the effectiveness of the scattering greenhouse effect caused by CO2 ice clouds, the radiative transfer calculations are performed over the relevant wide range of particle sizes and optical depths, employing different numerical methods. Methods: We used Mie theory to calculate the optical properties of particle polydispersion. The radiative transfer calculations were done with a high-order discrete ordinate method (DISORT). Two-stream radiative transfer methods were used for comparison with previous studies. Results: The comparison between the results of a high-order discrete ordinate method and simpler two-stream approaches reveals large deviations in terms of a potential scattering efficiency of the greenhouse effect. The two-stream methods overestimate the transmitted and reflected radiation, thereby yielding a higher scattering greenhouse effect. For the particular case of a cool M-type dwarf, the CO2 ice particles show no strong effective scattering greenhouse effect by using the high-order discrete ordinate method, whereas a positive net greenhouse effect was found for the two-stream radiative transfer schemes. As a result, previous studies of the effects of CO2 ice clouds using two-stream approximations overrated the atmospheric warming caused by the scattering greenhouse effect. Consequently, the scattering greenhouse effect of CO2 ice particles seems to be less effective than previously estimated. In general, higher order radiative transfer methods are needed to describe the effects of CO2 ice clouds accurately as indicated by our numerical radiative transfer studies.

A compressible multiphase framework for simulating supersonic atomization

NASA Astrophysics Data System (ADS)

Regele, Jonathan D.; Garrick, Daniel P.; Hosseinzadeh-Nik, Zahra; Aslani, Mohamad; Owkes, Mark

2016-11-01

The study of atomization in supersonic combustors is critical in designing efficient and high performance scramjets. Numerical methods incorporating surface tension effects have largely focused on the incompressible regime as most atomization applications occur at low Mach numbers. Simulating surface tension effects in high speed compressible flow requires robust numerical methods that can handle discontinuities caused by both material interfaces and shocks. A shock capturing/diffused interface method is developed to simulate high-speed compressible gas-liquid flows with surface tension effects using the five-equation model. This includes developments that account for the interfacial pressure jump that occurs in the presence of surface tension. A simple and efficient method for computing local interface curvature is developed and an acoustic non-dimensional scaling for the surface tension force is proposed. The method successfully captures a variety of droplet breakup modes over a range of Weber numbers and demonstrates the impact of surface tension in countering droplet deformation in both subsonic and supersonic cross flows.

Bridgman growth of large-aperture yttrium calcium oxyborate crystal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Anhua, E-mail: wuanhua@mail.sic.ac.cn; Jiang, Linwen; Qian, Guoxing

2012-09-15

Highlights: ► YCOB is a novel non-linear optical crystal possessing good thermal, mechanical and nonlinear optical properties. ► Large size crystal growth is key technology question for YCOB crystal. ► YCOB crystals 3 in. in diameter were grown with modified vertical Bridgman method. ► It is a more effective growth method to obtain large size and high quality YCOB crystal. -- Abstract: Large-aperture yttrium calcium oxyborate YCa{sub 4}O(BO{sub 3}){sub 3} (YCOB) crystals with 3 in. in diameter were grown with modified vertical Bridgman method, and the large crystal plate (63 mm × 68 mm × 20 mm) was harvested formore » high-average power frequency conversion system. The crack, facet growth and spiral growth can be effectively controlled in the as-grown crystal, and Bridgman method displays more effective in obtain large size and high quality YCOB crystal plate than Czochralski technique.« less

An enhanced data visualization method for diesel engine malfunction classification using multi-sensor signals.

PubMed

Li, Yiqing; Wang, Yu; Zi, Yanyang; Zhang, Mingquan

2015-10-21

The various multi-sensor signal features from a diesel engine constitute a complex high-dimensional dataset. The non-linear dimensionality reduction method, t-distributed stochastic neighbor embedding (t-SNE), provides an effective way to implement data visualization for complex high-dimensional data. However, irrelevant features can deteriorate the performance of data visualization, and thus, should be eliminated a priori. This paper proposes a feature subset score based t-SNE (FSS-t-SNE) data visualization method to deal with the high-dimensional data that are collected from multi-sensor signals. In this method, the optimal feature subset is constructed by a feature subset score criterion. Then the high-dimensional data are visualized in 2-dimension space. According to the UCI dataset test, FSS-t-SNE can effectively improve the classification accuracy. An experiment was performed with a large power marine diesel engine to validate the proposed method for diesel engine malfunction classification. Multi-sensor signals were collected by a cylinder vibration sensor and a cylinder pressure sensor. Compared with other conventional data visualization methods, the proposed method shows good visualization performance and high classification accuracy in multi-malfunction classification of a diesel engine.

An Enhanced Data Visualization Method for Diesel Engine Malfunction Classification Using Multi-Sensor Signals

PubMed Central

Li, Yiqing; Wang, Yu; Zi, Yanyang; Zhang, Mingquan

2015-01-01

The various multi-sensor signal features from a diesel engine constitute a complex high-dimensional dataset. The non-linear dimensionality reduction method, t-distributed stochastic neighbor embedding (t-SNE), provides an effective way to implement data visualization for complex high-dimensional data. However, irrelevant features can deteriorate the performance of data visualization, and thus, should be eliminated a priori. This paper proposes a feature subset score based t-SNE (FSS-t-SNE) data visualization method to deal with the high-dimensional data that are collected from multi-sensor signals. In this method, the optimal feature subset is constructed by a feature subset score criterion. Then the high-dimensional data are visualized in 2-dimension space. According to the UCI dataset test, FSS-t-SNE can effectively improve the classification accuracy. An experiment was performed with a large power marine diesel engine to validate the proposed method for diesel engine malfunction classification. Multi-sensor signals were collected by a cylinder vibration sensor and a cylinder pressure sensor. Compared with other conventional data visualization methods, the proposed method shows good visualization performance and high classification accuracy in multi-malfunction classification of a diesel engine. PMID:26506347

Emerging technologies for the prevention of dental caries. Are current methods of prevention sufficient for the high risk patient?

PubMed Central

Bretz, Walter A; Rosa, Odila P S

2011-01-01

Fluorides and chlorhexidine are technologies that are 65 and 40 yeas old, respectively. This overview argues that current methods of caries prevention are not effective for the high caries risk patient. In this review examples, arguments and recommendations are provided to address the high caries risk patient that include: failure of comprehensive chemical modalities treatments to address the high caries risk patient; ecological alteration - would this be an effective approach?; and biomaterials and oral microbiome research to address the high caries risk patient. PMID:21726223

Female Leadership at High-Poverty, High-Performing Schools: Four Case Studies

ERIC Educational Resources Information Center

Reynolds, Shirley Ann

2009-01-01

This mixed methods study examined the leadership abilities of four African American female principals in an urban setting. The purpose of the mixed methods study was to observe, describe and analyze how the principals have been effective leaders in their respective high-poverty, high-performing elementary schools (K-5). The qualitative methodology…

Comparison of High-Order and Low-Order Methods for Large-Eddy Simulation of a Compressible Shear Layer

NASA Technical Reports Server (NTRS)

Mankbadi, M. R.; Georgiadis, N. J.; DeBonis, J. R.

2015-01-01

The objective of this work is to compare a high-order solver with a low-order solver for performing large-eddy simulations (LES) of a compressible mixing layer. The high-order method is the Wave-Resolving LES (WRLES) solver employing a Dispersion Relation Preserving (DRP) scheme. The low-order solver is the Wind-US code, which employs the second-order Roe Physical scheme. Both solvers are used to perform LES of the turbulent mixing between two supersonic streams at a convective Mach number of 0.46. The high-order and low-order methods are evaluated at two different levels of grid resolution. For a fine grid resolution, the low-order method produces a very similar solution to the high-order method. At this fine resolution the effects of numerical scheme, subgrid scale modeling, and filtering were found to be negligible. Both methods predict turbulent stresses that are in reasonable agreement with experimental data. However, when the grid resolution is coarsened, the difference between the two solvers becomes apparent. The low-order method deviates from experimental results when the resolution is no longer adequate. The high-order DRP solution shows minimal grid dependence. The effects of subgrid scale modeling and spatial filtering were found to be negligible at both resolutions. For the high-order solver on the fine mesh, a parametric study of the spanwise width was conducted to determine its effect on solution accuracy. An insufficient spanwise width was found to impose an artificial spanwise mode and limit the resolved spanwise modes. We estimate that the spanwise depth needs to be 2.5 times larger than the largest coherent structures to capture the largest spanwise mode and accurately predict turbulent mixing.

Evaluating and addressing the effects of regression to the mean phenomenon in estimating collision frequencies on urban high collision concentration locations.

PubMed

Lee, Jinwoo; Chung, Koohong; Kang, Seungmo

2016-12-01

Two different methods for addressing the regression to the mean phenomenon (RTM) were evaluated using empirical data: Data from 110 miles of freeway located in California were used to evaluate the performance of the EB and CRP methods in addressing RTM. CRP outperformed the EB method in estimating collision frequencies in selected high collision concentration locations (HCCLs). Findings indicate that the performance of the EB method can be markedly affected when SPF is biased, while the performance of CRP remains much less affected. The CRP method was more effective in addressing RTM. Published by Elsevier Ltd.

The Implementation of PAIKEM (Active, Innovative, Creative, Effective, and Exciting Learning) and Conventional Learning Method to Improve Student Learning Results

ERIC Educational Resources Information Center

Priyono

2018-01-01

The research aims to find the differences in students' learning results by implementing both PAIKEM (Active, Innovative, Creative, Effective, and Exciting Learning) and conventional learning methods for students with high and low motivation. This research used experimental design on two groups, a group of high motivation students and a group of…

Nodal Diffusion Burnable Poison Treatment for Prismatic Reactor Cores

DOE Office of Scientific and Technical Information (OSTI.GOV)

A. M. Ougouag; R. M. Ferrer

2010-10-01

The prismatic block version of the High Temperature Reactor (HTR) considered as a candidate Very High Temperature Reactor (VHTR)design may use burnable poison pins in locations at some corners of the fuel blocks (i.e., assembly equivalent structures). The presence of any highly absorbing materials, such as these burnable poisons, within fuel blocks for hexagonal geometry, graphite-moderated High Temperature Reactors (HTRs) causes a local inter-block flux depression that most nodal diffusion-based method have failed to properly model or otherwise represent. The location of these burnable poisons near vertices results in an asymmetry in the morphology of the assemblies (or blocks). Hencemore » the resulting inadequacy of traditional homogenization methods, as these “spread” the actually local effect of the burnable poisons throughout the assembly. Furthermore, the actual effect of the burnable poison is primarily local with influence in its immediate vicinity, which happens to include a small region within the same assembly as well as similar regions in the adjacent assemblies. Traditional homogenization methods miss this artifact entirely. This paper presents a novel method for treating the local effect of the burnable poison explicitly in the context of a modern nodal method.« less

A new method for weakening the combined effect of residual errors on multibeam bathymetric data

NASA Astrophysics Data System (ADS)

Zhao, Jianhu; Yan, Jun; Zhang, Hongmei; Zhang, Yuqing; Wang, Aixue

2014-12-01

Multibeam bathymetric system (MBS) has been widely applied in the marine surveying for providing high-resolution seabed topography. However, some factors degrade the precision of bathymetry, including the sound velocity, the vessel attitude, the misalignment angle of the transducer and so on. Although these factors have been corrected strictly in bathymetric data processing, the final bathymetric result is still affected by their residual errors. In deep water, the result usually cannot meet the requirements of high-precision seabed topography. The combined effect of these residual errors is systematic, and it's difficult to separate and weaken the effect using traditional single-error correction methods. Therefore, the paper puts forward a new method for weakening the effect of residual errors based on the frequency-spectrum characteristics of seabed topography and multibeam bathymetric data. Four steps, namely the separation of the low-frequency and the high-frequency part of bathymetric data, the reconstruction of the trend of actual seabed topography, the merging of the actual trend and the extracted microtopography, and the accuracy evaluation, are involved in the method. Experiment results prove that the proposed method could weaken the combined effect of residual errors on multibeam bathymetric data and efficiently improve the accuracy of the final post-processing results. We suggest that the method should be widely applied to MBS data processing in deep water.

High correlations between MRI brain volume measurements based on NeuroQuant® and FreeSurfer.

PubMed

Ross, David E; Ochs, Alfred L; Tate, David F; Tokac, Umit; Seabaugh, John; Abildskov, Tracy J; Bigler, Erin D

2018-05-30

NeuroQuant ® (NQ) and FreeSurfer (FS) are commonly used computer-automated programs for measuring MRI brain volume. Previously they were reported to have high intermethod reliabilities but often large intermethod effect size differences. We hypothesized that linear transformations could be used to reduce the large effect sizes. This study was an extension of our previously reported study. We performed NQ and FS brain volume measurements on 60 subjects (including normal controls, patients with traumatic brain injury, and patients with Alzheimer's disease). We used two statistical approaches in parallel to develop methods for transforming FS volumes into NQ volumes: traditional linear regression, and Bayesian linear regression. For both methods, we used regression analyses to develop linear transformations of the FS volumes to make them more similar to the NQ volumes. The FS-to-NQ transformations based on traditional linear regression resulted in effect sizes which were small to moderate. The transformations based on Bayesian linear regression resulted in all effect sizes being trivially small. To our knowledge, this is the first report describing a method for transforming FS to NQ data so as to achieve high reliability and low effect size differences. Machine learning methods like Bayesian regression may be more useful than traditional methods. Copyright © 2018 Elsevier B.V. All rights reserved.

Extractions of High Quality RNA from the Seeds of Jerusalem Artichoke and Other Plant Species with High Levels of Starch and Lipid.

PubMed

Mornkham, Tanupat; Wangsomnuk, Preeya Puangsomlee; Fu, Yong-Bi; Wangsomnuk, Pinich; Jogloy, Sanun; Patanothai, Aran

2013-04-29

Jerusalem artichoke (Helianthus tuberosus L.) is an important tuber crop. However, Jerusalem artichoke seeds contain high levels of starch and lipid, making the extraction of high-quality RNA extremely difficult and the gene expression analysis challenging. This study was aimed to improve existing methods for extracting total RNA from Jerusalem artichoke dry seeds and to assess the applicability of the improved method in other plant species. Five RNA extraction methods were evaluated on Jerusalem artichoke seeds and two were modified. One modified method with the significant improvement was applied to assay seeds of diverse Jerusalem artichoke accessions, sunflower, rice, maize, peanut and marigold. The effectiveness of the improved method to extract total RNA from seeds was assessed using qPCR analysis of four selected genes. The improved method of Ma and Yang (2011) yielded a maximum RNA solubility and removed most interfering substances. The improved protocol generated 29 to 41 µg RNA/30 mg fresh weight. An A260/A280 ratio of 1.79 to 2.22 showed their RNA purity. Extracted RNA was effective for downstream applications such as first-stranded cDNA synthesis, cDNA cloning and qPCR. The improved method was also effective to extract total RNA from seeds of sunflower, rice, maize and peanut that are rich in polyphenols, lipids and polysaccharides.

Determination of Cluster Distances from Chandra Imaging Spectroscopy and Sunyaev-Zeldovich Effect Measurements. I; Analysis Methods and Initial Results

NASA Technical Reports Server (NTRS)

Bonamente, Massimiliano; Joy, Marshall K.; Carlstrom, John E.; LaRoque, Samuel J.

2004-01-01

X-ray and Sunyaev-Zeldovich Effect data ca,n be combined to determine the distance to galaxy clusters. High-resolution X-ray data are now available from the Chandra Observatory, which provides both spatial and spectral information, and interferometric radio measurements of the Sunyam-Zeldovich Effect are available from the BIMA and 0VR.O arrays. We introduce a Monte Carlo Markov chain procedure for the joint analysis of X-ray and Sunyaev-Zeldovich Effect data. The advantages of this method are the high computational efficiency and the ability to measure the full probability distribution of all parameters of interest, such as the spatial and spectral properties of the cluster gas and the cluster distance. We apply this technique to the Chandra X-ray data and the OVRO radio data for the galaxy cluster Abell 611. Comparisons with traditional likelihood-ratio methods reveal the robustness of the method. This method will be used in a follow-up paper to determine the distance of a large sample of galaxy clusters for which high-resolution Chandra X-ray and BIMA/OVRO radio data are available.

An Optimal Control Modification to Model-Reference Adaptive Control for Fast Adaptation

NASA Technical Reports Server (NTRS)

Nguyen, Nhan T.; Krishnakumar, Kalmanje; Boskovic, Jovan

2008-01-01

This paper presents a method that can achieve fast adaptation for a class of model-reference adaptive control. It is well-known that standard model-reference adaptive control exhibits high-gain control behaviors when a large adaptive gain is used to achieve fast adaptation in order to reduce tracking error rapidly. High gain control creates high-frequency oscillations that can excite unmodeled dynamics and can lead to instability. The fast adaptation approach is based on the minimization of the squares of the tracking error, which is formulated as an optimal control problem. The necessary condition of optimality is used to derive an adaptive law using the gradient method. This adaptive law is shown to result in uniform boundedness of the tracking error by means of the Lyapunov s direct method. Furthermore, this adaptive law allows a large adaptive gain to be used without causing undesired high-gain control effects. The method is shown to be more robust than standard model-reference adaptive control. Simulations demonstrate the effectiveness of the proposed method.

A novel automatic quantification method for high-content screening analysis of DNA double strand-break response.

PubMed

Feng, Jingwen; Lin, Jie; Zhang, Pengquan; Yang, Songnan; Sa, Yu; Feng, Yuanming

2017-08-29

High-content screening is commonly used in studies of the DNA damage response. The double-strand break (DSB) is one of the most harmful types of DNA damage lesions. The conventional method used to quantify DSBs is γH2AX foci counting, which requires manual adjustment and preset parameters and is usually regarded as imprecise, time-consuming, poorly reproducible, and inaccurate. Therefore, a robust automatic alternative method is highly desired. In this manuscript, we present a new method for quantifying DSBs which involves automatic image cropping, automatic foci-segmentation and fluorescent intensity measurement. Furthermore, an additional function was added for standardizing the measurement of DSB response inhibition based on co-localization analysis. We tested the method with a well-known inhibitor of DSB response. The new method requires only one preset parameter, which effectively minimizes operator-dependent variations. Compared with conventional methods, the new method detected a higher percentage difference of foci formation between different cells, which can improve measurement accuracy. The effects of the inhibitor on DSB response were successfully quantified with the new method (p = 0.000). The advantages of this method in terms of reliability, automation and simplicity show its potential in quantitative fluorescence imaging studies and high-content screening for compounds and factors involved in DSB response.

Introduction and Effectiveness of New Methods of Instruction Using Literature in a Japanese High School Setting

ERIC Educational Resources Information Center

Richings, Vicky Ann; Nishimuro, Masateru

2017-01-01

This paper reports on findings from a classroom study on the introduction and effectiveness of new methods of instruction using English literature in a Japanese high school setting. It is based on data compiled during a two-year research project. In this paper, we will detail the investigation and findings from an analysis of student questionnaire…

Effect of severing method and stump height on coppice growth

Treesearch

John B. Crist; James A. Mattson; Sharon A. Winsauer

1983-01-01

In this study we evaluated the effect of stem severing method and stump height on coppice growth in a short-rotation intensively cultured Populus plantation 1, 2, and 3 years after cutting. Initially, stumps 46 cm high had smaller and significantly more sprouts than either 8 or 15 cm high stumps. However, the dominant sprouts were not affected by the stump height....

An Exploration into the Potential Career Effects from Middle and High School Mathematics Experiences: A Mixed Methods Investigation into STEM Career Choice

ERIC Educational Resources Information Center

DeThomas, Elizabeth M.

2017-01-01

This mixed methods research study examined the effects of middle and high school mathematics experiences on students' choice of college major, particularly whether students decided to major in a STEM field. Social cognitive career theory was used to examine potential influences of mathematics self-efficacy and how those influences and mathematics…

Vacuum lamination approach to fabrication of high-performance single-crystal organic field-effect transistors.

PubMed

Yi, H T; Chen, Y; Czelen, K; Podzorov, V

2011-12-22

A novel vacuum lamination approach to fabrication of high-performance single-crystal organic field-effect transistors has been developed. The non-destructive nature of this method allows a direct comparison of field-effect mobilities achieved with various gate dielectrics using the same single-crystal sample. The method also allows gating delicate systems, such as n -type crystals and SAM-coated surfaces, without perturbation. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A comparison of methods to assess the antimicrobial activity of nanoparticle combinations on bacterial cells.

PubMed

Bankier, Claire; Cheong, Yuen; Mahalingam, Suntharavathanan; Edirisinghe, Mohan; Ren, Guogang; Cloutman-Green, Elaine; Ciric, Lena

2018-01-01

Bacterial cell quantification after exposure to antimicrobial compounds varies widely throughout industry and healthcare. Numerous methods are employed to quantify these antimicrobial effects. With increasing demand for new preventative methods for disease control, we aimed to compare and assess common analytical methods used to determine antimicrobial effects of novel nanoparticle combinations on two different pathogens. Plate counts of total viable cells, flow cytometry (LIVE/DEAD BacLight viability assay) and qPCR (viability qPCR) were used to assess the antimicrobial activity of engineered nanoparticle combinations (NPCs) on Gram-positive (Staphylococcus aureus) and Gram-negative (Pseudomonas aeruginosa) bacteria at different concentrations (0.05, 0.10 and 0.25 w/v%). Results were analysed using linear models to assess the effectiveness of different treatments. Strong antimicrobial effects of the three NPCs (AMNP0-2) on both pathogens could be quantified using the plate count method and flow cytometry. The plate count method showed a high log reduction (>8-log) for bacteria exposed to high NPC concentrations. We found similar antimicrobial results using the flow cytometry live/dead assay. Viability qPCR analysis of antimicrobial activity could not be quantified due to interference of NPCs with qPCR amplification. Flow cytometry was determined to be the best method to measure antimicrobial activity of the novel NPCs due to high-throughput, rapid and quantifiable results.

Assessment of methods for methyl iodide emission reduction and pest control using a simulation model

USDA-ARS?s Scientific Manuscript database

Various methods have been developed to reduce atmospheric emissions from the agricultural use of highly volatile pesticides and mitigate their adverse environmental effects. The effectiveness of various methods on emissions reduction and pest control was assessed using simulation model in this study...

Evaluation of a High Intensity Focused Ultrasound-Immobilized Trypsin Digestion and 18O-Labeling Method for Quantitative Proteomics

PubMed Central

López-Ferrer, Daniel; Hixson, Kim K.; Smallwood, Heather; Squier, Thomas C.; Petritis, Konstantinos; Smith, Richard D.

2009-01-01

A new method that uses immobilized trypsin concomitant with ultrasonic irradiation results in ultra-rapid digestion and thorough 18O labeling for quantitative protein comparisons. The reproducible and highly efficient method provided effective digestions in <1 min with a minimized amount of enzyme required compared to traditional methods. This method was demonstrated for digestion of both simple and complex protein mixtures, including bovine serum albumin, a global proteome extract from the bacteria Shewanella oneidensis, and mouse plasma, as well as 18O labeling of such complex protein mixtures, which validated the application of this method for differential proteomic measurements. This approach is simple, reproducible, cost effective, rapid, and thus well-suited for automation. PMID:19555078

Comparison of High-Order and Low-Order Methods for Large-Eddy Simulation of a Compressible Shear Layer

NASA Technical Reports Server (NTRS)

Mankbadi, Mina R.; Georgiadis, Nicholas J.; DeBonis, James R.

2015-01-01

The objective of this work is to compare a high-order solver with a low-order solver for performing Large-Eddy Simulations (LES) of a compressible mixing layer. The high-order method is the Wave-Resolving LES (WRLES) solver employing a Dispersion Relation Preserving (DRP) scheme. The low-order solver is the Wind-US code, which employs the second-order Roe Physical scheme. Both solvers are used to perform LES of the turbulent mixing between two supersonic streams at a convective Mach number of 0.46. The high-order and low-order methods are evaluated at two different levels of grid resolution. For a fine grid resolution, the low-order method produces a very similar solution to the highorder method. At this fine resolution the effects of numerical scheme, subgrid scale modeling, and filtering were found to be negligible. Both methods predict turbulent stresses that are in reasonable agreement with experimental data. However, when the grid resolution is coarsened, the difference between the two solvers becomes apparent. The low-order method deviates from experimental results when the resolution is no longer adequate. The high-order DRP solution shows minimal grid dependence. The effects of subgrid scale modeling and spatial filtering were found to be negligible at both resolutions. For the high-order solver on the fine mesh, a parametric study of the spanwise width was conducted to determine its effect on solution accuracy. An insufficient spanwise width was found to impose an artificial spanwise mode and limit the resolved spanwise modes. We estimate that the spanwise depth needs to be 2.5 times larger than the largest coherent structures to capture the largest spanwise mode and accurately predict turbulent mixing.

Characteristics of Highly Effective Cooperating Teachers: A Study of Their Backgrounds and Preparation

ERIC Educational Resources Information Center

Killian, Joyce E.; Wilkins, Elizabeth A.

2009-01-01

This study used interviews and other artifacts collected during student teaching as the basis for rating 13 elementary cooperating teachers on their supervisory effectiveness. Once highly effective cooperating teachers were differentiated from their less effective peers, researchers used ex post facto methods to identify background and…

Characteristics of High School Students' and Science Teachers' Cognitive Frame about Effective Teaching Method for High School Science Subject

NASA Astrophysics Data System (ADS)

Chung, Duk Ho; Park, Kyeong-Jin; Cho, Kyu Seong

2016-04-01

We investigated the cognitive frame of high school students and inservice high school science teachers about effective teaching method, and we also explored how they understood about the teaching methods suggested by the 2009 revised Science Curriculum. Data were collected from 275 high school science teachers and 275 high school students. We analyzed data in terms of the words and the cognitive frame using the Semantic Network Analysis. The results were as follows. First, the teachers perceived that an activity oriented class was the effective science class that helped improve students'' problem-solving abilities and their inquiry skills. The students had the cognitive frame that their teacher had to present relevant and enough teaching materials to students, and that they should also receive assistance from teachers in science class to better prepare for college entrance exam. Second, both students and teachers retained the cognitive frame about the efficient science class that was not reflected 2009 revised Science Curriculum exactly. Especially, neither groups connected the elements of ''convergence'' as well as ''integration'' embedded across science subject areas to their cognitive frame nor cognized the fact that many science learning contents were closed related to one another. Therefore, various professional development opportunities should be offered so that teachers succinctly comprehend the essential features and the intents of the 2009 revised Science Curriculum and thereby implement it in their science lessons effectively. Keywords : semantic network analysis, cognitive frame, teaching method, science lesson

High-quality Health Information Provision for Stroke Patients.

PubMed

Du, Hong-Sheng; Ma, Jing-Jian; Li, Mu

2016-09-05

High-quality information provision can allow stroke patients to effectively participate in healthcare decision-making, better manage the stroke, and make a good recovery. In this study, we reviewed information needs of stroke patients, methods for providing information to patients, and considerations needed by the information providers. The literature concerning or including information provision for patients with stroke in English was collected from PubMed published from 1990 to 2015. We included all the relevant articles on information provision for stroke patients in English, with no limitation of study design. Stroke is a major public health concern worldwide. High-quality and effective health information provision plays an essential role in helping patients to actively take part in decision-making and healthcare, and empowering them to effectively self-manage their long-standing chronic conditions. Different methods for providing information to patients have their relative merits and suitability, and as a result, the effective strategies taken by health professionals may include providing high-quality information, meeting patients' individual needs, using suitable methods in providing information, and maintaining active involvement of patients. It is suggested that to enable stroke patients to access high-quality health information, greater efforts need to be made to ensure patients to receive accurate and current evidence-based information which meets their individual needs. Health professionals should use suitable information delivery methods, and actively involve stroke patients in information provision.

Highly anisotropic mobility in solution processed TIPS-pentacene film studied by independently driven four GaIn probes

NASA Astrophysics Data System (ADS)

Yoshimoto, Shinya; Takahashi, Kohtaro; Suzuki, Mitsuharu; Yamada, Hiroko; Miyahara, Ryosuke; Mukai, Kozo; Yoshinobu, Jun

2017-08-01

We have studied in-plane anisotropy in the field-effect mobility of solution-processed organic semiconductor 6,13-bis(triisopropylsilylethynyl)pentacene by using independently driven four gallium indium (Ga-In) probes. Liquid-metal Ga-In probes are highly effective for reproducible conductivity measurements of organic thin films. We demonstrated that a high mobility anisotropy of 44 was obtained by using a square four-probe method and a feedback circuit to keep the channel potential constant. The present method minimized the influences of the contact resistance and the insensitivity of anisotropy in a linear arrangement in two-dimensional field-effect transistors.

Triple effect absorption chiller utilizing two refrigeration circuits

DOEpatents

DeVault, Robert C.

1988-01-01

A triple effect absorption method and apparatus having a high coefficient of performance. Two single effect absorption circuits are combined with heat exchange occurring between a condenser and absorber of a high temperature circuit, and a generator of a low temperature circuit. The evaporators of both the high and low temperature circuits provide cooling to an external heat load.

Informing the introduction of contraceptive implants in the Pacific: a mixed methods study of contraceptive beliefs and behaviours in Tonga.

PubMed

Winn-Dix, Edward A; Nathan, Sally A; Rawstorne, Patrick

2016-04-01

To explore the knowledge and attitudes underlying contraceptive use and non-use among Tongan adults and investigate the potential acceptability of contraceptive implants. A mixed methods study was conducted that used two focus groups and a short self-completed survey (n=109). Participants were recruited from a Tongan non-governmental sexual and reproductive health clinic. Contraceptive method discontinuation was high among the study group, with reasons for discontinuation often relating to misconceptions circulating in the community about the side effects of contraceptives. A high proportion (38%) reported using 'natural' contraceptive methods. A total of 47% of survey participants reported having heard of implants and 37% indicated they would be willing to try them. Current Tongan contraceptive uptake and continuation is hampered by misconceptions about side effects of methods and their risks, particularly among long-acting and reversible methods. Contraceptive implants may be acceptable to Tongans given their arm placement, reversibility and long-lasting effect. Efforts to improve contraceptive continuation in Tonga should focus on improving counselling on potential side effects for all methods. The introduction of contraceptive implants as an additional long-acting reversible method should be considered. © 2015 Public Health Association of Australia.

Application of seismic interferometric migration for shallow seismic high precision data processing: A case study in the Shenhu area

NASA Astrophysics Data System (ADS)

Wei, Jia; Liu, Huaishan; Xing, Lei; Du, Dong

2018-02-01

The stability of submarine geological structures has a crucial influence on the construction of offshore engineering projects and the exploitation of seabed resources. Marine geologists should possess a detailed understanding of common submarine geological hazards. Current marine seismic exploration methods are based on the most effective detection technologies. Therefore, current research focuses on improving the resolution and precision of shallow stratum structure detection methods. In this article, the feasibility of shallow seismic structure imaging is assessed by building a complex model, and differences between the seismic interferometry imaging method and the traditional imaging method are discussed. The imaging effect of the model is better for shallow layers than for deep layers because coherent noise produced by this method can result in an unsatisfactory imaging effect for deep layers. The seismic interference method has certain advantages for geological structural imaging of shallow submarine strata, which indicates continuous horizontal events, a high resolution, a clear fault, and an obvious structure boundary. The effects of the actual data applied to the Shenhu area can fully illustrate the advantages of the method. Thus, this method has the potential to provide new insights for shallow submarine strata imaging in the area.

Simple fluorescence-based high throughput cell viability assay for filamentous fungi.

PubMed

Chadha, S; Kale, S P

2015-09-01

Filamentous fungi are important model organisms to understand the eukaryotic process and have been frequently exploited in research and industry. These fungi are also causative agents of serious diseases in plants and humans. Disease management strategies include in vitro susceptibility testing of the fungal pathogens to environmental conditions and antifungal agents. Conventional methods used for antifungal susceptibilities are cumbersome, time-consuming and are not suitable for a large-scale analysis. Here, we report a rapid, high throughput microplate-based fluorescence method for investigating the toxicity of antifungal and stress (osmotic, salt and oxidative) agents on Magnaporthe oryzae and compared it with agar dilution method. This bioassay is optimized for the resazurin reduction to fluorescent resorufin by the fungal hyphae. Resazurin bioassay showed inhibitory rates and IC50 values comparable to the agar dilution method and to previously reported IC50 or MICs for M. oryzae and other fungi. The present method can screen range of test agents from different chemical classes with different modes of action for antifungal activities in a simple, sensitive, time and cost effective manner. A simple fluorescence-based high throughput method is developed to test the effects of stress and antifungal agents on viability of filamentous fungus Magnaporthe oryzae. This resazurin fluorescence assay can detect inhibitory effects comparable to those obtained using the growth inhibition assay with added advantages of simplicity, time and cost effectiveness. This high throughput viability assay has a great potential in large-scale screening of the chemical libraries of antifungal agents, for evaluating the effects of environmental conditions and hyphal kinetic studies in mutant and natural populations of filamentous fungi. © 2015 The Society for Applied Microbiology.

Quartz-Seq2: a high-throughput single-cell RNA-sequencing method that effectively uses limited sequence reads.

PubMed

Sasagawa, Yohei; Danno, Hiroki; Takada, Hitomi; Ebisawa, Masashi; Tanaka, Kaori; Hayashi, Tetsutaro; Kurisaki, Akira; Nikaido, Itoshi

2018-03-09

High-throughput single-cell RNA-seq methods assign limited unique molecular identifier (UMI) counts as gene expression values to single cells from shallow sequence reads and detect limited gene counts. We thus developed a high-throughput single-cell RNA-seq method, Quartz-Seq2, to overcome these issues. Our improvements in the reaction steps make it possible to effectively convert initial reads to UMI counts, at a rate of 30-50%, and detect more genes. To demonstrate the power of Quartz-Seq2, we analyzed approximately 10,000 transcriptomes from in vitro embryonic stem cells and an in vivo stromal vascular fraction with a limited number of reads.

High degree reduction and restoration of graphene oxide on SiO2 at low temperature via remote Cu-assisted plasma treatment.

PubMed

Obata, Seiji; Sato, Minoru; Akada, Keishi; Saiki, Koichiro

2018-06-15

A high throughput synthesis method of graphene has been required for a long time to apply graphene to industrial applications. Of the various synthesis methods, the chemical exfoliation of graphite via graphene oxide (GO) is advantageous as far as productivity is concerned; however, the quality of the graphene produced by this method is far inferior to that synthesized by other methods, such as chemical vapor deposition on metals. Developing an effective reduction and restoration method for GO on dielectric substrates has been therefore a key issue. Here, we present a method for changing GO deposited on a dielectric substrate into high crystallinity graphene at 550 °C; this method uses CH 4 /H 2 plasma and a Cu catalyst. We found that Cu remotely catalyzed the high degree reduction and restoration of GO on SiO 2 and the effect ranged over at least 8 mm. With this method, field-effect transistor devices can be fabricated without any post treatment such as a transfer process. This plasma treatment increased electron and hole mobilities of GO to 480 cm 2 V -1 s -1 and 460 cm 2 V -1 s -1 respectively; these values were more than 50 times greater than that of conventional reduced GO. Furthermore, the on-site conversion ensured that the shape of the GO sheets remained unchanged after the treatment. This plasma treatment realizes the high throughput synthesis of a desired shaped graphene on any substrate without any residue and damage being caused by the transfer process; as such, it expands the potential applicability of graphene.

High degree reduction and restoration of graphene oxide on SiO2 at low temperature via remote Cu-assisted plasma treatment

NASA Astrophysics Data System (ADS)

Obata, Seiji; Sato, Minoru; Akada, Keishi; Saiki, Koichiro

2018-06-01

A high throughput synthesis method of graphene has been required for a long time to apply graphene to industrial applications. Of the various synthesis methods, the chemical exfoliation of graphite via graphene oxide (GO) is advantageous as far as productivity is concerned; however, the quality of the graphene produced by this method is far inferior to that synthesized by other methods, such as chemical vapor deposition on metals. Developing an effective reduction and restoration method for GO on dielectric substrates has been therefore a key issue. Here, we present a method for changing GO deposited on a dielectric substrate into high crystallinity graphene at 550 °C this method uses CH4/H2 plasma and a Cu catalyst. We found that Cu remotely catalyzed the high degree reduction and restoration of GO on SiO2 and the effect ranged over at least 8 mm. With this method, field-effect transistor devices can be fabricated without any post treatment such as a transfer process. This plasma treatment increased electron and hole mobilities of GO to 480 cm2 V‑1 s‑1 and 460 cm2 V‑1 s‑1 respectively; these values were more than 50 times greater than that of conventional reduced GO. Furthermore, the on-site conversion ensured that the shape of the GO sheets remained unchanged after the treatment. This plasma treatment realizes the high throughput synthesis of a desired shaped graphene on any substrate without any residue and damage being caused by the transfer process; as such, it expands the potential applicability of graphene.

Promoted combustion of nine structural metals in high-pressure gaseous oxygen - A comparison of ranking methods

NASA Technical Reports Server (NTRS)

Steinberg, Theodore A.; Rucker, Michelle A.; Beeson, Harold D.

1989-01-01

The 316, 321, 440C, and 17-4 PH stainless steels, as well as Inconel 600, Inconel 718, Waspaloy, Monel 400, and Al 2219, have been evaluated for relative nonflammability in a high-pressure oxygen environment with a view to the comparative advantages of four different flammability-ranking methods. The effects of changes in test pressure, sample diameter, promoter type, and sample configuration on ranking method results are evaluated; ranking methods employing velocity as the primary ranking criterion are limited by diameter effects, while those which use extinguishing pressure are nonselective for metals with similar flammabilities.

Selective detection of cavitation bubbles by triplet pulse sequence in high-intensity focused ultrasound treatment

NASA Astrophysics Data System (ADS)

Iwasaki, Ryosuke; Nagaoka, Ryo; Yoshizawa, Shin; Umemura, Shin-ichiro

2018-07-01

Acoustic cavitation bubbles are known to enhance the heating effect in high-intensity focused ultrasound (HIFU) treatment. The detection of cavitation bubbles with high sensitivity and selectivity is required to predict the therapeutic and side effects of cavitation, and ensure the efficacy and safety of the treatment. A pulse inversion (PI) technique has been widely used for imaging microbubbles through enhancing the second-harmonic component of echo signals. However, it has difficulty in separating the nonlinear response of microbubbles from that due to nonlinear propagation. In this study, a triplet pulse (3P) method was investigated to specifically image cavitation bubbles by extracting the 1.5th fractional harmonic component. The proposed 3P method depicted cavitation bubbles with a contrast ratio significantly higher than those in conventional imaging methods with and without PI. The results suggest that the 3P method is effective for specifically detecting microbubbles in cavitation-enhanced HIFU treatment.

An improved AE detection method of rail defect based on multi-level ANC with VSS-LMS

NASA Astrophysics Data System (ADS)

Zhang, Xin; Cui, Yiming; Wang, Yan; Sun, Mingjian; Hu, Hengshan

2018-01-01

In order to ensure the safety and reliability of railway system, Acoustic Emission (AE) method is employed to investigate rail defect detection. However, little attention has been paid to the defect detection at high speed, especially for noise interference suppression. Based on AE technology, this paper presents an improved rail defect detection method by multi-level ANC with VSS-LMS. Multi-level noise cancellation based on SANC and ANC is utilized to eliminate complex noises at high speed, and tongue-shaped curve with index adjustment factor is proposed to enhance the performance of variable step-size algorithm. Defect signals and reference signals are acquired by the rail-wheel test rig. The features of noise signals and defect signals are analyzed for effective detection. The effectiveness of the proposed method is demonstrated by comparing with the previous study, and different filter lengths are investigated to obtain a better noise suppression performance. Meanwhile, the detection ability of the proposed method is verified at the top speed of the test rig. The results clearly illustrate that the proposed method is effective in detecting rail defects at high speed, especially for noise interference suppression.

Effectiveness of E-Learning for Students Vocational High School Building Engineering Program

NASA Astrophysics Data System (ADS)

Soeparno; Muslim, Supari

2018-04-01

Implementation of vocational learning in accordance with the 2013 curriculum must meet the criteria, one of which is learning to be consistent with advances in technology and information. Technology-based learning in vocational commonly referred to as E-Learning, online (in the network) and WBL (Web-Based Learning). Facts on the ground indicate that based learning technology and information on Vocational High School of Building Engineering is still not going well. The purpose of this research is to know: advantages and disadvantages of learning with E-Learning, conformity of learning with E-Learning with characteristics of students on Vocational High School of Building Engineering and effective learning method based on E-Learning for students on Vocational High School of Building Engineering. Research done by literature method, get the following conclusion as follow: the advantages of E-Learning is learning can be done anywhere and anytime, efficient in accessing materials and tasks, ease of communication and discussion; while the shortage is the need for additional costs for good internet access and lack of social interaction between teachers and students. E-learning is appropriate to basic knowledge competencies, and not appropriate at the level of advanced competencies and skills. Effective E-Learning Based Learning Method on Vocational High School of Building Engineering is a Blended method that is a mix between conventional method and e-learning.

Rugged passively cooled high power laser fiber optic connectors and methods of use

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rinzler, Charles C.; Gray, William C.; Fraze, Jason D.

2016-06-07

There are provided high power laser connectors and couplers and methods that are capable of providing high laser power without the need for active cooling to remote, harsh and difficult to access locations and under difficult and harsh conditions and to manage and mitigate the adverse effects of back reflections.

The effects of modeling instruction on high school physics academic achievement

NASA Astrophysics Data System (ADS)

Wright, Tiffanie L.

The purpose of this study was to explore whether Modeling Instruction, compared to traditional lecturing, is an effective instructional method to promote academic achievement in selected high school physics classes at a rural middle Tennessee high school. This study used an ex post facto , quasi-experimental research methodology. The independent variables in this study were the instructional methods of teaching. The treatment variable was Modeling Instruction and the control variable was traditional lecture instruction. The Treatment Group consisted of participants in Physical World Concepts who received Modeling Instruction. The Control Group consisted of participants in Physical Science who received traditional lecture instruction. The dependent variable was gains scores on the Force Concepts Inventory (FCI). The participants for this study were 133 students each in both the Treatment and Control Groups (n = 266), who attended a public, high school in rural middle Tennessee. The participants were administered the Force Concepts Inventory (FCI) prior to being taught the mechanics of physics. The FCI data were entered into the computer-based Statistical Package for the Social Science (SPSS). Two independent samples t-tests were conducted to answer the research questions. There was a statistically significant difference between the treatment and control groups concerning the instructional method. Modeling Instructional methods were found to be effective in increasing the academic achievement of students in high school physics. There was no statistically significant difference between FCI gains scores for gender. Gender was found to have no effect on the academic achievement of students in high school physics classes. However, even though there was not a statistically significant difference, female students' gains scores were higher than male students' gains scores when Modeling Instructional methods of teaching were used. Based on these findings, it is recommended that high school science teachers should use Modeling Instructional methods of teaching daily in their classrooms. A recommendation for further research is to expand the Modeling Instructional methods of teaching into different content areas, (i.e., reading and language arts) to explore academic achievement gains.

Effective donor cell fusion conditions for production of cloned dogs by somatic cell nuclear transfer.

PubMed

Park, JungEun; Oh, HyunJu; Hong, SoGun; Kim, MinJung; Kim, GeonA; Koo, OkJae; Kang, SungKeun; Jang, Goo; Lee, ByeongChun

2011-03-01

As shown by the birth of the first cloned dog 'Snuppy', a protocol to produce viable cloned dogs has been reported. In order to evaluate optimum fusion conditions for improving dog cloning efficiency, in vivo matured oocytes were reconstructed with adult somatic cells from a female Pekingese using different fusion conditions. Fusion with needle vs chamber methods, and with low vs high pulse strength was compared by evaluating fusion rate and in vivo development of canine cloned embryos. The fusion rates in the high voltage groups were significantly higher than in the low voltage groups regardless of fusion method (83.5 vs 66.1% for the needle fusion method, 67.4 vs 37.9% for the fusion chamber method). After embryo transfer, one each pregnancy was detected after using the needle fusion method with high and low voltage and in the chamber fusion method with high voltage, whereas no pregnancy was detected using the chamber method with low voltage. However, only the pregnancy from the needle fusion method with high voltage was maintained to term and one healthy puppy was delivered. The results of the present study demonstrated that two DC pulses of 3.8 to 4.0 kV/cm for 15 μsec using the needle fusion method were the most effective method for the production of cloned dogs under the conditions of this experiment. Copyright © 2011 Elsevier Inc. All rights reserved.

Method to estimate the effective temperatures of late-type giants using line-depth ratios in the wavelength range 0.97-1.32 μm

NASA Astrophysics Data System (ADS)

Taniguchi, Daisuke; Matsunaga, Noriyuki; Kobayashi, Naoto; Fukue, Kei; Hamano, Satoshi; Ikeda, Yuji; Kawakita, Hideyo; Kondo, Sohei; Sameshima, Hiroaki; Yasui, Chikako

2018-02-01

The effective temperature, one of the most fundamental atmospheric parameters of a star, can be estimated using various methods; here, we focus on a method using line-depth ratios (LDRs). This method combines low- and high-excitation lines and makes use of relations between LDRs of these line pairs and the effective temperature. It has an advantage, for example, of being minimally affected by interstellar reddening, which changes stellar colours. We report 81 relations between LDRs and effective temperature established with high-resolution, λ/Δλ ∼ 28 000, spectra of nine G- to M-type giants in the Y and J bands. Our analysis gives the first comprehensive set of LDR relations for this wavelength range. The combination of all these relations can be used to determine the effective temperatures of stars that have 3700 < Teff < 5400 K and -0.5 < [Fe/H] < +0.3 dex, to a precision of ±10 K in the best cases.

On the transmit field inhomogeneity correction of relaxation‐compensated amide and NOE CEST effects at 7 T

PubMed Central

Windschuh, Johannes; Siero, Jeroen C.W.; Zaiss, Moritz; Luijten, Peter R.; Klomp, Dennis W.J.; Hoogduin, Hans

2017-01-01

High field MRI is beneficial for chemical exchange saturation transfer (CEST) in terms of high SNR, CNR, and chemical shift dispersion. These advantages may, however, be counter‐balanced by the increased transmit field inhomogeneity normally associated with high field MRI. The relatively high sensitivity of the CEST contrast to B 1 inhomogeneity necessitates the development of correction methods, which is essential for the clinical translation of CEST. In this work, two B 1 correction algorithms for the most studied CEST effects, amide‐CEST and nuclear Overhauser enhancement (NOE), were analyzed. Both methods rely on fitting the multi‐pool Bloch‐McConnell equations to the densely sampled CEST spectra. In the first method, the correction is achieved by using a linear B 1 correction of the calculated amide and NOE CEST effects. The second method uses the Bloch‐McConnell fit parameters and the desired B 1 amplitude to recalculate the CEST spectra, followed by the calculation of B 1‐corrected amide and NOE CEST effects. Both algorithms were systematically studied in Bloch‐McConnell equations and in human data, and compared with the earlier proposed ideal interpolation‐based B 1 correction method. In the low B 1 regime of 0.15–0.50 μT (average power), a simple linear model was sufficient to mitigate B 1 inhomogeneity effects on a par with the interpolation B 1 correction, as demonstrated by a reduced correlation of the CEST contrast with B 1 in both the simulations and the experiments. PMID:28111824

Magselectofection: an integrated method of nanomagnetic separation and genetic modification of target cells.

PubMed

Sanchez-Antequera, Yolanda; Mykhaylyk, Olga; van Til, Niek P; Cengizeroglu, Arzu; de Jong, J Henk; Huston, Marshall W; Anton, Martina; Johnston, Ian C D; Pojda, Zygmunt; Wagemaker, Gerard; Plank, Christian

2011-04-21

Research applications and cell therapies involving genetically modified cells require reliable, standardized, and cost-effective methods for cell manipulation. We report a novel nanomagnetic method for integrated cell separation and gene delivery. Gene vectors associated with magnetic nanoparticles are used to transfect/transduce target cells while being passaged and separated through a high gradient magnetic field cell separation column. The integrated method yields excellent target cell purity and recovery. Nonviral and lentiviral magselectofection is efficient and highly specific for the target cell population as demonstrated with a K562/Jurkat T-cell mixture. Both mouse and human enriched hematopoietic stem cell pools were effectively transduced by lentiviral magselectofection, which did not affect the hematopoietic progenitor cell number determined by in vitro colony assays. Highly effective reconstitution of T and B lymphocytes was achieved by magselectofected murine wild-type lineage-negative Sca-1(+) cells transplanted into Il2rg(-/-) mice, stably expressing GFP in erythroid, myeloid, T-, and B-cell lineages. Furthermore, nonviral, lentiviral, and adenoviral magselectofection yielded high transfection/transduction efficiency in human umbilical cord mesenchymal stem cells and was fully compatible with their differentiation potential. Upscaling to a clinically approved automated cell separation device was feasible. Hence, once optimized, validated, and approved, the method may greatly facilitate the generation of genetically engineered cells for cell therapies.

Apparatus and method for magnetically processing a specimen

DOEpatents

Ludtka, Gerard M; Ludtka, Gail M; Wilgen, John B; Kisner, Roger A; Jaramillo, Roger A

2013-09-03

An apparatus for magnetically processing a specimen that couples high field strength magnetic fields with the magnetocaloric effect includes a high field strength magnet capable of generating a magnetic field of at least 1 Tesla and a magnetocaloric insert disposed within a bore of the high field strength magnet. A method for magnetically processing a specimen includes positioning a specimen adjacent to a magnetocaloric insert within a bore of a magnet and applying a high field strength magnetic field of at least 1 Tesla to the specimen and to the magnetocaloric insert. The temperature of the specimen changes during the application of the high field strength magnetic field due to the magnetocaloric effect.

Research study on high energy radiation effect and environment solar cell degradation methods

NASA Technical Reports Server (NTRS)

Horne, W. E.; Wilkinson, M. C.

1974-01-01

The most detailed and comprehensively verified analytical model was used to evaluate the effects of simplifying assumptions on the accuracy of predictions made by the external damage coefficient method. It was found that the most serious discrepancies were present in heavily damaged cells, particularly proton damaged cells, in which a gradient in damage across the cell existed. In general, it was found that the current damage coefficient method tends to underestimate damage at high fluences. An exception to this rule was thick cover-slipped cells experiencing heavy degradation due to omnidirectional electrons. In such cases, the damage coefficient method overestimates the damage. Comparisons of degradation predictions made by the two methods and measured flight data confirmed the above findings.

An Efficient Variable Screening Method for Effective Surrogate Models for Reliability-Based Design Optimization

DTIC Science & Technology

2014-04-01

surrogate model generation is difficult for high -dimensional problems, due to the curse of dimensionality. Variable screening methods have been...a variable screening model was developed for the quasi-molecular treatment of ion-atom collision [16]. In engineering, a confidence interval of...for high -level radioactive waste [18]. Moreover, the design sensitivity method can be extended to the variable screening method because vital

Highly Effective Birth Control Use Before and After Women's Incarceration.

PubMed

Ramaswamy, Megha; Chen, Hsiang-Feng; Cropsey, Karen L; Clarke, Jennifer G; Kelly, Patricia J

2015-06-01

We examined factors associated with women's use of highly effective birth control before and after incarceration, since women with ongoing criminal justice involvement bear a disproportionate burden of sexual and reproductive health problems, including high rates of unintended pregnancy and inconsistent contraceptive use. Using a longitudinal study design, we conducted surveys with 102 women in an urban midwestern jail and then followed up with 66 of them 6 months after incarceration. We used stepwise logistic regression to assess individual, interpersonal, resource-based, organizational, and environmental factors associated with utilizing highly effective birth control. Forty-two percent of women reported utilizing highly effective birth control (e.g., sterilization or other highly effective reversible methods) prior to incarceration, and 54% reported using these methods after release from jail (p<0.001). Ninety percent of women reported not wanting to get pregnant. Consistent use of birth control (p=0.001) and alcohol problems (p=0.027) were associated with utilization of highly effective birth control prior to incarceration. Previous pregnancies (p=0.012) were the only factor associated with utilization of highly effective birth control after release from jail. Clinicians and public health practitioners can use findings from this study to develop clinical and intervention efforts aimed at improving unintended-pregnancy prevention among incarcerated women both during their confinement and during the tumultuous period after their release from jail.

Effects of Comprehensive, Multiple High-Risk Behaviors Prevention Program on High School Students

ERIC Educational Resources Information Center

Collier, Crystal

2013-01-01

The purpose of this mixed methods study was to examine the effect of a multiple high-risk behaviors prevention program applied comprehensively throughout an entire school-system involving universal, selective, and indicated levels of students at a local private high school during a 4-year period. The prevention program was created based upon the…

Comparison of Effective Medium Schemes For Seismic Velocities in Cracked Anisotropic Rock

NASA Astrophysics Data System (ADS)

Morshed, S.; Chesnokov, E.

2017-12-01

Understanding of elastic properties of reservoir rock is necessary for meaningful interpretation and analysis of seismic measurements. The elastic properties of a rock are controlled by the microstructural properties such as mineralogical composition, pore and crack distribution, texture and pore connectivity. However, seismic scale is much larger than microstructure scale. Understanding of macroscopic properties at relevant seismic scale (e.g. borehole sonic data) comes from effective medium theory (EMT). However, most of the effective medium theories fail at high crack density as the interactions of strain fields of the cracks can't be ignored. We compare major EMT schemes from low to high crack density. While at low crack density all method gives similar results, at high crack density they differ significantly. Then, we focus on generalized singular approximation (GSA) and effective field (EF) method as they allow cracks beyond the limit of dilute concentrations. Additionally, we use grain contact (GC) method to examine the stiffness constants of the rock matrix. We prepare simple models of a multiphase media containing low to high concentrations of isolated pores. Randomly oriented spherical pores and horizontally oriented ellipsoidal (aspect ratio =0.1) pores have been considered. For isolated spherical pores, all the three methods show exactly same or similar results. However, inclusion interactions are different in different directions in case of horizontal ellipsoidal pores and individual stiffness constants differ greatly from one method to another at different crack density. Stiffness constants remain consistent in GSA method whereas some components become unusual in EF method at a higher crack density (>0.15). Finally, we applied GSA method to interpret ultrasonic velocities of core samples. Mineralogical composition from X-ray diffraction (XRD) data and lab measured porosity data have been utilized. Both compressional and shear wave velocities from GSA method show good fit with the lab measured velocities.

The Effect of the Computer Assisted Teaching and 7e Model of the Constructivist Learning Methods on the Achievements and Attitudes of High School Students

ERIC Educational Resources Information Center

Gönen, Selahattin; Kocakaya, Serhat; Inan, Cemil

2006-01-01

This study provides a comparative effect study of the Computer Assisted Teaching and the 7E model of the Constructivist Learning methods on attitudes and achievements of the students in physics classes. The experiments have been carried out in a private high school in Diyarbakir/Turkey on groups of first year students whose pre-test scores of…

[Genome editing of industrial microorganism].

PubMed

Zhu, Linjiang; Li, Qi

2015-03-01

Genome editing is defined as highly-effective and precise modification of cellular genome in a large scale. In recent years, such genome-editing methods have been rapidly developed in the field of industrial strain improvement. The quickly-updating methods thoroughly change the old mode of inefficient genetic modification, which is "one modification, one selection marker, and one target site". Highly-effective modification mode in genome editing have been developed including simultaneous modification of multiplex genes, highly-effective insertion, replacement, and deletion of target genes in the genome scale, cut-paste of a large DNA fragment. These new tools for microbial genome editing will certainly be applied widely, and increase the efficiency of industrial strain improvement, and promote the revolution of traditional fermentation industry and rapid development of novel industrial biotechnology like production of biofuel and biomaterial. The technological principle of these genome-editing methods and their applications were summarized in this review, which can benefit engineering and construction of industrial microorganism.

Evaluation of a new modified QuEChERS method for the monitoring of carbamate residues in high-fat cheeses by using UHPLC-MS/MS.

PubMed

Hamed, Ahmed M; Moreno-González, David; Gámiz-Gracia, Laura; García-Campaña, Ana M

2017-01-01

A simple and efficient method for the determination of 28 carbamates in high-fat cheeses is proposed. The methodology is based on a modified quick, easy, cheap, effective, rugged, and safe procedure as sample treatment using a new sorbent (Z-Sep + ) followed by ultra-high performance liquid chromatography with tandem mass spectrometry determination. The method has been validated in different kinds of cheese (Gorgonzola, Roquefort, and Camembert), achieving recoveries of 70-115%, relative standard deviations lower than 13% and limits of quantification lower than 5.4 μg/kg, below the maximum residue levels tolerated for these compounds by the European legislation. The matrix effect was lower than ±30% for all the studied pesticides. The combination of ultra-high performance liquid chromatography and tandem mass spectrometry with this modified quick, easy, cheap, effective, rugged, and safe procedure using Z-Sep + allowed a high sample throughput and an efficient cleaning of extracts for the control of these residues in cheeses with a high fat content. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Pressure Self-focusing Effect and Novel Methods for Increasing the Maximum Pressure in Traditional and Rotational Diamond Anvil Cells.

PubMed

Feng, Biao; Levitas, Valery I

2017-04-21

The main principles of producing a region near the center of a sample, compressed in a diamond anvil cell (DAC), with a very high pressure gradient and, consequently, with high pressure are predicted theoretically. The revealed phenomenon of generating extremely high pressure gradient is called the pressure self-focusing effect. Initial analytical predictions utilized generalization of a simplified equilibrium equation. Then, the results are refined using our recent advanced model for elastoplastic material under high pressures in finite element method (FEM) simulations. The main points in producing the pressure self-focusing effect are to use beveled anvils and reach a very thin sample thickness at the center. We find that the superposition of torsion in a rotational DAC (RDAC) offers drastic enhancement of the pressure self-focusing effect and allows one to reach the same pressure under a much lower force and deformation of anvils.

An Organic Vertical Field-Effect Transistor with Underside-Doped Graphene Electrodes.

PubMed

Kim, Jong Su; Kim, Beom Joon; Choi, Young Jin; Lee, Moo Hyung; Kang, Moon Sung; Cho, Jeong Ho

2016-06-01

High-performance vertical field-effect transistors are developed, which are based on graphene electrodes doped using the underside doping method. The underside doping method enables effective tuning of the graphene work function while maintaining the surface properties of the pristine graphene. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Food, Fun and Fitness Internet program for girls: influencing log-on rate

USDA-ARS?s Scientific Manuscript database

Internet-based interventions hold promise as an effective channel for reaching large numbers of youth. However, log-on rates, a measure of program dose, have been highly variable. Methods to enhance log-on rate are needed. Incentives may be an effective method. This paper reports the effect of reinf...

Comparison of various RNA extraction methods, cDNA preparation and isolation of calmodulin gene from a highly melanized isolate of apple leaf blotch fungus Marssonina coronaria.

PubMed

Chauhan, Arjun; Sharma, J N; Modgil, Manju; Siddappa, Sundaresha

2018-05-29

Marssonina coronaria causes apple blotch disease resulting in severe premature defoliation, and is distributed in many leading apple-growing areas in the world. Effective, reliable and high-quality RNA extraction is an indispensable procedure in any molecular biology study. No method currently exists for RNA extraction from M. coronaria that produces a high quantity of melanin-free RNA. Therefore, we evaluated eight RNA extraction methods including manual and commercial kits, to yield a sufficient quantity of high-quality and melanin-free RNA. Manual methods used here resulted in low quality and black colored RNA pellets showing the presence of melanin, despite all the modifications employed to original procedures. However, these methods when coupled with clean up resulted in melanin-free RNA. On the other hand, all commercial kits used were able to yield high-quality melanin-free RNA having variable yields. TRIzol™ Reagent + RNA Clean & Concentrator™-5 and Ambion-PureLink® RNA Mini Kit were found to be the best methods as the RNA extracted with these methods from 15 day old fungal culture grown on solid medium were free of melanin with good yield. RNA extracted by this improved methodology was applied for RT-PCR, subsequent PCR amplification, and isolation of calmodulin gene sequences from M. coronaria and infected apple leaf pieces. These methods are more time effective than traditional methods and take only an hour to complete. To our knowledge, this is the first report on the method of isolation of high-quality RNA for cDNA synthesis as well as isolation of the calmodulin gene sequence from this fungus. Copyright © 2018 Elsevier B.V. All rights reserved.

A rough set-based measurement model study on high-speed railway safety operation.

PubMed

Hu, Qizhou; Tan, Minjia; Lu, Huapu; Zhu, Yun

2018-01-01

Aiming to solve the safety problems of high-speed railway operation and management, one new method is urgently needed to construct on the basis of the rough set theory and the uncertainty measurement theory. The method should carefully consider every factor of high-speed railway operation that realizes the measurement indexes of its safety operation. After analyzing the factors that influence high-speed railway safety operation in detail, a rough measurement model is finally constructed to describe the operation process. Based on the above considerations, this paper redistricts the safety influence factors of high-speed railway operation as 16 measurement indexes which include staff index, vehicle index, equipment index and environment. And the paper also provides another reasonable and effective theoretical method to solve the safety problems of multiple attribute measurement in high-speed railway operation. As while as analyzing the operation data of 10 pivotal railway lines in China, this paper respectively uses the rough set-based measurement model and value function model (one model for calculating the safety value) for calculating the operation safety value. The calculation result shows that the curve of safety value with the proposed method has smaller error and greater stability than the value function method's, which verifies the feasibility and effectiveness.

Rayleigh-wave mode separation by high-resolution linear radon transform

USGS Publications Warehouse

Luo, Y.; Xia, J.; Miller, R.D.; Xu, Y.; Liu, J.; Liu, Q.

2009-01-01

Multichannel analysis of surface waves (MASW) method is an effective tool for obtaining vertical shear wave profiles from a single non-invasive measurement. One key step of the MASW method is generation of a dispersion image and extraction of a reliable dispersion curve from raw multichannel shot records. Because different Rayleigh-wave modes normally interfere with each other in the time and space domain, it is necessary to perform mode separation and reconstruction to increase the accuracy of phase velocities determined from a dispersion image. In this paper, we demonstrate the effectiveness of high-resolution linear Radon transform (LRT) as a means of separating and reconstructing multimode, dispersive Rayleigh-wave energy. We first introduce high-resolution LRT methods and Rayleigh-wave mode separation using high-resolution LRT. Next, we use synthetic data and a real-world example to demonstrate the effectiveness of Rayleigh-wave mode separation using high-resolution LRT. Our synthetic and real-world results demonstrate that (1) high-resolution LRT successfully separates and reconstructs multimode dispersive Rayleigh-wave energy with high resolution allowing the multimode energy to be more accurately determined. The horizontal resolution of the Rayleigh-wave method can be increased by extraction of dispersion curves from a pair of traces in the mode-separated shot gather and (2) multimode separation and reconstruction expand the usable frequency range of higher mode dispersive energy, which increases the depth of investigation and provides a means for accurately determining cut-off frequencies. ?? 2009 The Authors Journal compilation ?? 2009 RAS.

A simple, rapid, high-fidelity and cost-effective PCR-based two-step DNA synthesis method for long gene sequences.

PubMed

Xiong, Ai-Sheng; Yao, Quan-Hong; Peng, Ri-He; Li, Xian; Fan, Hui-Qin; Cheng, Zong-Ming; Li, Yi

2004-07-07

Chemical synthesis of DNA sequences provides a powerful tool for modifying genes and for studying gene function, structure and expression. Here, we report a simple, high-fidelity and cost-effective PCR-based two-step DNA synthesis (PTDS) method for synthesis of long segments of DNA. The method involves two steps. (i) Synthesis of individual fragments of the DNA of interest: ten to twelve 60mer oligonucleotides with 20 bp overlap are mixed and a PCR reaction is carried out with high-fidelity DNA polymerase Pfu to produce DNA fragments that are approximately 500 bp in length. (ii) Synthesis of the entire sequence of the DNA of interest: five to ten PCR products from the first step are combined and used as the template for a second PCR reaction using high-fidelity DNA polymerase pyrobest, with the two outermost oligonucleotides as primers. Compared with the previously published methods, the PTDS method is rapid (5-7 days) and suitable for synthesizing long segments of DNA (5-6 kb) with high G + C contents, repetitive sequences or complex secondary structures. Thus, the PTDS method provides an alternative tool for synthesizing and assembling long genes with complex structures. Using the newly developed PTDS method, we have successfully obtained several genes of interest with sizes ranging from 1.0 to 5.4 kb.

Application of finite-element methods to dynamic analysis of flexible spatial and co-planar linkage systems, part 2

NASA Technical Reports Server (NTRS)

Dubowsky, Steven

1989-01-01

An approach is described to modeling the flexibility effects in spatial mechanisms and manipulator systems. The method is based on finite element representations of the individual links in the system. However, it should be noted that conventional finite element methods and software packages will not handle the highly nonlinear dynamic behavior of these systems which results form their changing geometry. In order to design high-performance lightweight systems and their control systems, good models of their dynamic behavior which include the effects of flexibility are required.

Highly transparent cerium doped gadolinium gallium aluminum garnet ceramic prepared with precursors fabricated by ultrasonic enhanced chemical co-precipitation.

PubMed

Zhang, Ji-Yun; Luo, Zhao-Hua; Jiang, Hao-Chuan; Jiang, Jun; Chen, Chun-Hua; Zhang, Jing-Xian; Gui, Zhen-Zhen; Xiao, Na

2017-11-01

Cerium doped gadolinium gallium aluminum garnet (GGAG:Ce) ceramic precursors have been synthesized with an ultrasonic chemical co-precipitation method (UCC) and for comparison with a traditional chemical co-precipitation method (TCC). The effect of ultra-sonication on the morphology of powders and the transmittance of GGAG:Ce ceramics are studied. The results indicate that the UCC method can effectively improve the homogenization and sinterability of GGAG:Ce powders, which contribute to obtain high transparent GGAG ceramic with the highest transmittance of 81%. Copyright © 2017 Elsevier B.V. All rights reserved.

Analysis of multi lobe journal bearings with surface roughness using finite difference method

NASA Astrophysics Data System (ADS)

PhaniRaja Kumar, K.; Bhaskar, SUdaya; Manzoor Hussain, M.

2018-04-01

Multi lobe journal bearings are used for high operating speeds and high loads in machines. In this paper symmetrical multi lobe journal bearings are analyzed to find out the effect of surface roughnessduring non linear loading. Using the fourth order RungeKutta method, time transient analysis was performed to calculate and plot the journal centre trajectories. Flow factor method is used to evaluate the roughness and the finite difference method (FDM) is used to predict the pressure distribution over the bearing surface. The Transient analysis is done on the multi lobe journal bearings for threedifferent surface roughness orientations. Longitudinal surface roughness is more effective when compared with isotopic and traverse surface roughness.

3D highly heterogeneous thermal model of pineal gland in-vitro study for electromagnetic exposure using finite volume method

NASA Astrophysics Data System (ADS)

Cen, Wei; Hoppe, Ralph; Lu, Rongbo; Cai, Zhaoquan; Gu, Ning

2017-08-01

In this paper, the relationship between electromagnetic power absorption and temperature distributions inside highly heterogeneous biological samples was accurately determinated using finite volume method. An in-vitro study on pineal gland that is responsible for physiological activities was for the first time simulated to illustrate effectiveness of the proposed method.

Improved Filon-type asymptotic methods for highly oscillatory differential equations with multiple time scales

NASA Astrophysics Data System (ADS)

Wang, Bin; Wu, Xinyuan

2014-11-01

In this paper we consider multi-frequency highly oscillatory second-order differential equations x″ (t) + Mx (t) = f (t , x (t) ,x‧ (t)) where high-frequency oscillations are generated by the linear part Mx (t), and M is positive semi-definite (not necessarily nonsingular). It is known that Filon-type methods are effective approach to numerically solving highly oscillatory problems. Unfortunately, however, existing Filon-type asymptotic methods fail to apply to the highly oscillatory second-order differential equations when M is singular. We study and propose an efficient improvement on the existing Filon-type asymptotic methods, so that the improved Filon-type asymptotic methods can be able to numerically solving this class of multi-frequency highly oscillatory systems with a singular matrix M. The improved Filon-type asymptotic methods are designed by combining Filon-type methods with the asymptotic methods based on the variation-of-constants formula. We also present one efficient and practical improved Filon-type asymptotic method which can be performed at lower cost. Accompanying numerical results show the remarkable efficiency.

Comparative estimation of the effectiveness of laser and other methods of stomatological disease treatment

NASA Astrophysics Data System (ADS)

Kunin, Anatoly A.; Erina, Stanislava V.; Pankova, Svetlana N.; Buerger, Friedhelm R.; Baumert, R.; Stepanov, Nicolay N.; Malinovskaya, L. A.; Sokolova, Irina A.; Podolskaya, Elana E.; Kazmina, Svetlana G.; Dergunova, Elvira I.; Mozhaev, N. N.

1996-11-01

A perspective trend in the perfection of laser methods of stomatological diseases treatment is the application of low intensity laser radiation having a wide range of the therapeutic effect. Thus, laser radiation has various, pathogenetic effect. Patients with carries, pulpits, periodontitis, diseases of parodontium and oral mucous membranes were treated. Traditional examination methods were used, i.e. biochemical, visual pulp examination, immunological and macrohistological ones. The obtained results prove high effectiveness of laser therapy in the treatment of a number of stomatological disease in comparison with traditional methods and can be recommended to be used in practice.

Implementation of a sliding-mode-based position sensorless drive for high-speed micro permanent-magnet synchronous motors.

PubMed

Chi, Wen-Chun; Cheng, Ming-Yang

2014-03-01

Due to issues such as limited space, it is difficult if it is not impossible to employ a position sensor in the drive control of high-speed micro PMSMs. In order to alleviate this problem, this paper analyzes and implements a simple and robust position sensorless field-oriented control method of high-speed micro PMSMs based on the sliding-mode observer. In particular, the angular position and velocity of the rotor of the high-speed micro PMSM are estimated using the sliding-mode observer. This observer is able to accurately estimate rotor position in the low speed region and guarantee fast convergence of the observer in the high speed region. The proposed position sensorless control method is suitable for electric dental handpiece motor drives where a wide speed range operation is essential. The proposed sensorless FOC method is implemented using a cost-effective 16-bit microcontroller and tested in a prototype electric dental handpiece motor. Several experiments are performed to verify the effectiveness of the proposed method. © 2013 ISA. Published by Elsevier Ltd. All rights reserved.

The Contextual Effect of School Satisfaction on Health-Risk Behaviors in Japanese High School Students

ERIC Educational Resources Information Center

Takakura, Minoru; Wake, Norie; Kobayashi, Minoru

2010-01-01

Background: The importance of school contextual effects on health and well-being among young people is currently recognized. This study examines the contextual effects of school satisfaction as well as the effects of individual-level school satisfaction on health-risk behaviors in Japanese high school students. Methods: Self-administered…

METHODS FOR MONITORING THE EFFECTS OF ENVIRONMENTAL TOXINS ON THE VISUAL SYSTEM.

EPA Science Inventory

A high percentage of neurotoxic compounds adversely effect the visual system. Our goal is to apply the tools of vision science to problems of toxicological import, exposure-related alterations in visual physiology, psychophysical function, and ocular development. Methods can ...

Dual energy approach for cone beam artifacts correction

NASA Astrophysics Data System (ADS)

Han, Chulhee; Choi, Shinkook; Lee, Changwoo; Baek, Jongduk

2017-03-01

Cone beam computed tomography systems generate 3D volumetric images, which provide further morphological information compared to radiography and tomosynthesis systems. However, reconstructed images by FDK algorithm contain cone beam artifacts when a cone angle is large. To reduce the cone beam artifacts, two-pass algorithm has been proposed. The two-pass algorithm considers the cone beam artifacts are mainly caused by high density materials, and proposes an effective method to estimate error images (i.e., cone beam artifacts images) by the high density materials. While this approach is simple and effective with a small cone angle (i.e., 5 - 7 degree), the correction performance is degraded as the cone angle increases. In this work, we propose a new method to reduce the cone beam artifacts using a dual energy technique. The basic idea of the proposed method is to estimate the error images generated by the high density materials more reliably. To do this, projection data of the high density materials are extracted from dual energy CT projection data using a material decomposition technique, and then reconstructed by iterative reconstruction using total-variation regularization. The reconstructed high density materials are used to estimate the error images from the original FDK images. The performance of the proposed method is compared with the two-pass algorithm using root mean square errors. The results show that the proposed method reduces the cone beam artifacts more effectively, especially with a large cone angle.

Multiscale Simulation Framework for Coupled Fluid Flow and Mechanical Deformation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hou, Thomas; Efendiev, Yalchin; Tchelepi, Hamdi

2016-05-24

Our work in this project is aimed at making fundamental advances in multiscale methods for flow and transport in highly heterogeneous porous media. The main thrust of this research is to develop a systematic multiscale analysis and efficient coarse-scale models that can capture global effects and extend existing multiscale approaches to problems with additional physics and uncertainties. A key emphasis is on problems without an apparent scale separation. Multiscale solution methods are currently under active investigation for the simulation of subsurface flow in heterogeneous formations. These procedures capture the effects of fine-scale permeability variations through the calculation of specialized coarse-scalemore » basis functions. Most of the multiscale techniques presented to date employ localization approximations in the calculation of these basis functions. For some highly correlated (e.g., channelized) formations, however, global effects are important and these may need to be incorporated into the multiscale basis functions. Other challenging issues facing multiscale simulations are the extension of existing multiscale techniques to problems with additional physics, such as compressibility, capillary effects, etc. In our project, we explore the improvement of multiscale methods through the incorporation of additional (single-phase flow) information and the development of a general multiscale framework for flows in the presence of uncertainties, compressible flow and heterogeneous transport, and geomechanics. We have considered (1) adaptive local-global multiscale methods, (2) multiscale methods for the transport equation, (3) operator-based multiscale methods and solvers, (4) multiscale methods in the presence of uncertainties and applications, (5) multiscale finite element methods for high contrast porous media and their generalizations, and (6) multiscale methods for geomechanics.« less

Multiscale analysis and computation for flows in heterogeneous media

DOE Office of Scientific and Technical Information (OSTI.GOV)

Efendiev, Yalchin; Hou, T. Y.; Durlofsky, L. J.

Our work in this project is aimed at making fundamental advances in multiscale methods for flow and transport in highly heterogeneous porous media. The main thrust of this research is to develop a systematic multiscale analysis and efficient coarse-scale models that can capture global effects and extend existing multiscale approaches to problems with additional physics and uncertainties. A key emphasis is on problems without an apparent scale separation. Multiscale solution methods are currently under active investigation for the simulation of subsurface flow in heterogeneous formations. These procedures capture the effects of fine-scale permeability variations through the calculation of specialized coarse-scalemore » basis functions. Most of the multiscale techniques presented to date employ localization approximations in the calculation of these basis functions. For some highly correlated (e.g., channelized) formations, however, global effects are important and these may need to be incorporated into the multiscale basis functions. Other challenging issues facing multiscale simulations are the extension of existing multiscale techniques to problems with additional physics, such as compressibility, capillary effects, etc. In our project, we explore the improvement of multiscale methods through the incorporation of additional (single-phase flow) information and the development of a general multiscale framework for flows in the presence of uncertainties, compressible flow and heterogeneous transport, and geomechanics. We have considered (1) adaptive local-global multiscale methods, (2) multiscale methods for the transport equation, (3) operator-based multiscale methods and solvers, (4) multiscale methods in the presence of uncertainties and applications, (5) multiscale finite element methods for high contrast porous media and their generalizations, and (6) multiscale methods for geomechanics. Below, we present a brief overview of each of these contributions.« less

UTILIZING THE PAKS METHOD FOR MEASURING ACROLEIN AND OTHER ALDEHYDES IN DEARS

EPA Science Inventory

Acrolein is a hazardous air pollutant of high priority due to its high irritation potency and other potential adverse health effects. However, a reliable method is currently unavailable for measuring airborne acrolein at typical environmental levels. In the Detroit Exposure and A...

Signal Processing Methods for Removing the Effects of Whole Body Vibration upon Speech

NASA Technical Reports Server (NTRS)

Bitner, Rachel M.; Begault, Durand R.

2014-01-01

Humans may be exposed to whole-body vibration in environments where clear speech communications are crucial, particularly during the launch phases of space flight and in high-performance aircraft. Prior research has shown that high levels of vibration cause a decrease in speech intelligibility. However, the effects of whole-body vibration upon speech are not well understood, and no attempt has been made to restore speech distorted by whole-body vibration. In this paper, a model for speech under whole-body vibration is proposed and a method to remove its effect is described. The method described reduces the perceptual effects of vibration, yields higher ASR accuracy scores, and may significantly improve intelligibility. Possible applications include incorporation within communication systems to improve radio-communication systems in environments such a spaceflight, aviation, or off-road vehicle operations.

Charge carrier mobility in thin films of organic semiconductors by the gated van der Pauw method

PubMed Central

Rolin, Cedric; Kang, Enpu; Lee, Jeong-Hwan; Borghs, Gustaaf; Heremans, Paul; Genoe, Jan

2017-01-01

Thin film transistors based on high-mobility organic semiconductors are prone to contact problems that complicate the interpretation of their electrical characteristics and the extraction of important material parameters such as the charge carrier mobility. Here we report on the gated van der Pauw method for the simple and accurate determination of the electrical characteristics of thin semiconducting films, independently from contact effects. We test our method on thin films of seven high-mobility organic semiconductors of both polarities: device fabrication is fully compatible with common transistor process flows and device measurements deliver consistent and precise values for the charge carrier mobility and threshold voltage in the high-charge carrier density regime that is representative of transistor operation. The gated van der Pauw method is broadly applicable to thin films of semiconductors and enables a simple and clean parameter extraction independent from contact effects. PMID:28397852

Characteristics of holey fibers fabricated at different drawing speeds

NASA Astrophysics Data System (ADS)

Seraji, Faramarz E.; Rashidi, Mahnaz; Karimi, Maryam

2007-03-01

The effects of high drawing speeds on parameters of holey fibers are presented. A holey fiber preform structure was made by using tube-in-tube method and was drawn at high speeds with an aim of mass production to meet the demand of next generation communication systems. Transmission parameters such as numerical aperture and normalized frequency of the fabricated holey fibers have been measured and compared with theoretical values based on effective index method. Although the fabricated holey fibers were not of high quality, the analyses of the parameters have shown promising outlook for fabrication of such fibers.

Frequency of data extraction errors and methods to increase data extraction quality: a methodological review.

PubMed

Mathes, Tim; Klaßen, Pauline; Pieper, Dawid

2017-11-28

Our objective was to assess the frequency of data extraction errors and its potential impact on results in systematic reviews. Furthermore, we evaluated the effect of different extraction methods, reviewer characteristics and reviewer training on error rates and results. We performed a systematic review of methodological literature in PubMed, Cochrane methodological registry, and by manual searches (12/2016). Studies were selected by two reviewers independently. Data were extracted in standardized tables by one reviewer and verified by a second. The analysis included six studies; four studies on extraction error frequency, one study comparing different reviewer extraction methods and two studies comparing different reviewer characteristics. We did not find a study on reviewer training. There was a high rate of extraction errors (up to 50%). Errors often had an influence on effect estimates. Different data extraction methods and reviewer characteristics had moderate effect on extraction error rates and effect estimates. The evidence base for established standards of data extraction seems weak despite the high prevalence of extraction errors. More comparative studies are needed to get deeper insights into the influence of different extraction methods.

[Application of three risk assessment models in occupational health risk assessment of dimethylformamide].

PubMed

Wu, Z J; Xu, B; Jiang, H; Zheng, M; Zhang, M; Zhao, W J; Cheng, J

2016-08-20

Objective: To investigate the application of United States Environmental Protection Agency (EPA) inhalation risk assessment model, Singapore semi-quantitative risk assessment model, and occupational hazards risk assessment index method in occupational health risk in enterprises using dimethylformamide (DMF) in a certain area in Jiangsu, China, and to put forward related risk control measures. Methods: The industries involving DMF exposure in Jiangsu province were chosen as the evaluation objects in 2013 and three risk assessment models were used in the evaluation. EPA inhalation risk assessment model: HQ=EC/RfC; Singapore semi-quantitative risk assessment model: Risk= (HR×ER) 1/2 ; Occupational hazards risk assessment index=2 Health effect level ×2 exposure ratio ×Operation condition level. Results: The results of hazard quotient (HQ>1) from EPA inhalation risk assessment model suggested that all the workshops (dry method, wet method and printing) and work positions (pasting, burdening, unreeling, rolling, assisting) were high risk. The results of Singapore semi-quantitative risk assessment model indicated that the workshop risk level of dry method, wet method and printing were 3.5 (high) , 3.5 (high) and 2.8 (general) , and position risk level of pasting, burdening, unreeling, rolling, assisting were 4 (high) , 4 (high) , 2.8 (general) , 2.8 (general) and 2.8 (general) . The results of occupational hazards risk assessment index method demonstrated that the position risk index of pasting, burdening, unreeling, rolling, assisting were 42 (high) , 33 (high) , 23 (middle) , 21 (middle) and 22 (middle) . The results of Singapore semi-quantitative risk assessment model and occupational hazards risk assessment index method were similar, while EPA inhalation risk assessment model indicated all the workshops and positions were high risk. Conclusion: The occupational hazards risk assessment index method fully considers health effects, exposure, and operating conditions and can comprehensively and accurately evaluate occupational health risk caused by DMF.

Reflective and refractive objects for mixed reality.

PubMed

Knecht, Martin; Traxler, Christoph; Winklhofer, Christoph; Wimmer, Michael

2013-04-01

In this paper, we present a novel rendering method which integrates reflective or refractive objects into a differential instant radiosity (DIR) framework usable for mixed-reality (MR) applications. This kind of objects are very special from the light interaction point of view, as they reflect and refract incident rays. Therefore they may cause high-frequency lighting effects known as caustics. Using instant-radiosity (IR) methods to approximate these high-frequency lighting effects would require a large amount of virtual point lights (VPLs) and is therefore not desirable due to real-time constraints. Instead, our approach combines differential instant radiosity with three other methods. One method handles more accurate reflections compared to simple cubemaps by using impostors. Another method is able to calculate two refractions in real-time, and the third method uses small quads to create caustic effects. Our proposed method replaces parts in light paths that belong to reflective or refractive objects using these three methods and thus tightly integrates into DIR. In contrast to previous methods which introduce reflective or refractive objects into MR scenarios, our method produces caustics that also emit additional indirect light. The method runs at real-time frame rates, and the results show that reflective and refractive objects with caustics improve the overall impression for MR scenarios.

Identification Method of Mud Shale Fractures Base on Wavelet Transform

NASA Astrophysics Data System (ADS)

Xia, Weixu; Lai, Fuqiang; Luo, Han

2018-01-01

In recent years, inspired by seismic analysis technology, a new method for analysing mud shale fractures oil and gas reservoirs by logging properties has emerged. By extracting the high frequency attribute of the wavelet transform in the logging attribute, the formation information hidden in the logging signal is extracted, identified the fractures that are not recognized by conventional logging and in the identified fracture segment to show the “cycle jump”, “high value”, “spike” and other response effect is more obvious. Finally formed a complete wavelet denoising method and wavelet high frequency identification fracture method.

Method For Testing Properties Of Corrosive Lubricants

DOEpatents

Ohi, James; De La Cruz, Jose L.; Lacey, Paul I.

2006-01-03

A method of testing corrosive lubricating media using a wear testing apparatus without a mechanical seal. The wear testing apparatus and methods are effective for testing volatile corrosive lubricating media under pressure and at high temperatures.

In situ flash x-ray high-speed computed tomography for the quantitative analysis of highly dynamic processes

NASA Astrophysics Data System (ADS)

Moser, Stefan; Nau, Siegfried; Salk, Manfred; Thoma, Klaus

2014-02-01

The in situ investigation of dynamic events, ranging from car crash to ballistics, often is key to the understanding of dynamic material behavior. In many cases the important processes and interactions happen on the scale of milli- to microseconds at speeds of 1000 m s-1 or more. Often, 3D information is necessary to fully capture and analyze all relevant effects. High-speed 3D-visualization techniques are thus required for the in situ analysis. 3D-capable optical high-speed methods often are impaired by luminous effects and dust, while flash x-ray based methods usually deliver only 2D data. In this paper, a novel 3D-capable flash x-ray based method, in situ flash x-ray high-speed computed tomography is presented. The method is capable of producing 3D reconstructions of high-speed processes based on an undersampled dataset consisting of only a few (typically 3 to 6) x-ray projections. The major challenges are identified, discussed and the chosen solution outlined. The application is illustrated with an exemplary application of a 1000 m s-1 high-speed impact event on the scale of microseconds. A quantitative analysis of the in situ measurement of the material fragments with a 3D reconstruction with 1 mm voxel size is presented and the results are discussed. The results show that the HSCT method allows gaining valuable visual and quantitative mechanical information for the understanding and interpretation of high-speed events.

Contraceptive practices of women with epilepsy: Findings of the epilepsy birth control registry.

PubMed

Herzog, Andrew G; Mandle, Hannah B; Cahill, Kaitlyn E; Fowler, Kristen M; Hauser, W Allen; Davis, Anne R

2016-04-01

To report the contraceptive practices of women with epilepsy (WWE) in the community, predictors of highly effective contraception use, and reasons WWE provide for the selection of a particular method. These cross-sectional data come from the Epilepsy Birth Control Registry (EBCR) web-based survey regarding the contraceptive practices of 1,144 WWE in the community, ages 18-47 years. We report demographic, epilepsy, and antiepileptic drug (AED) characteristics as well as contraceptive use. We determined the frequency of use of highly effective contraception use, that is, methods with failure rate <10%/year, and conducted binary logistic regression analysis to determine predictors of highly effective contraception use. We report frequencies of WWE who consult various health care providers regarding the selection of a method and the reasons cited for selection. Of the 796 WWE at risk of unintended pregnancy, 69.7% use what is generally considered to be highly effective contraception (hormonal, intrauterine device [IUD], tubal, vasectomy). Efficacy in WWE, especially for the 46.6% who use hormonal contraception, remains to be proven. Significant predictors of highly effective contraception use are insurance (insured 71.6% vs. noninsured 56.0%), race/ethnicity (Caucasian 71.3% vs. minority 51.0%), and age (38-47, 77.5%; 28-37, 71.8%; 18-27, 67.0%). Of the 87.2% who have a neurologist, only 25.4% consult them regarding selection of a method, although AED interaction is cited as the top reason for selection. The EBCR web-based survey is the first large-scale study of the contraceptive practices of WWE in the community. The findings suggest a need for the development of evidence-based guidelines that address the efficacy and safety of contraceptive methods in this special population, and for greater discourse between neurologists and WWE regarding contraception. Wiley Periodicals, Inc. © 2016 International League Against Epilepsy.

High-throughput genotyping of hop (Humulus lupulus L.) utilising diversity arrays technology (DArT)

USDA-ARS?s Scientific Manuscript database

Implementation of molecular methods in hop breeding is dependent on the availability of sizeable numbers of polymorphic markers and a comprehensive understanding of genetic variation. Diversity Arrays Technology (DArT) is a high-throughput cost-effective method for the discovery of large numbers of...

Pretreatment of Biomass by Aqueous Ammonia for Bioethanol Production

NASA Astrophysics Data System (ADS)

Kim, Tae Hyun; Gupta, Rajesh; Lee, Y. Y.

The methods of pretreatment of lignocellulosic biomass using aqueous ammonia are described. The main effect of ammonia treatment of biomass is delignification without significantly affecting the carbohydrate contents. It is a very effective pretreatment method especially for substrates that have low lignin contents such as agricultural residues and herbaceous feedstock. The ammonia-based pretreatment is well suited for simultaneous saccharification and co-fermentation (SSCF) because the treated biomass retains cellulose as well as hemicellulose. It has been demonstrated that overall ethanol yield above 75% of the theoretical maximum on the basis of total carbohydrate is achievable from corn stover pretreated with aqueous ammonia by way of SSCF. There are two different types of pretreatment methods based on aqueous ammonia: (1) high severity, low contact time process (ammonia recycle percolation; ARP), (2) low severity, high treatment time process (soaking in aqueous ammonia; SAA). Both of these methods are described and discussed for their features and effectiveness.

A kinetic method for the determination of thiourea by its catalytic effect in micellar media

NASA Astrophysics Data System (ADS)

Abbasi, Shahryar; Khani, Hossein; Gholivand, Mohammad Bagher; Naghipour, Ali; Farmany, Abbas; Abbasi, Freshteh

2009-03-01

A highly sensitive, selective and simple kinetic method was developed for the determination of trace levels of thiourea based on its catalytic effect on the oxidation of janus green in phosphoric acid media and presence of Triton X-100 surfactant without any separation and pre-concentration steps. The reaction was monitored spectrophotometrically by tracing the formation of the green-colored oxidized product of janus green at 617 nm within 15 min of mixing the reagents. The effect of some factors on the reaction speed was investigated. Following the recommended procedure, thiourea could be determined with linear calibration graph in 0.03-10.00 μg/ml range. The detection limit of the proposed method is 0.02 μg/ml. Most of foreign species do not interfere with the determination. The high sensitivity and selectivity of the proposed method allowed its successful application to fruit juice and industrial waste water.

Quantitative measurement of pass-by noise radiated by vehicles running at high speeds

NASA Astrophysics Data System (ADS)

Yang, Diange; Wang, Ziteng; Li, Bing; Luo, Yugong; Lian, Xiaomin

2011-03-01

It has been a challenge in the past to accurately locate and quantify the pass-by noise source radiated by the running vehicles. A system composed of a microphone array is developed in our current work to do this work. An acoustic-holography method for moving sound sources is designed to handle the Doppler effect effectively in the time domain. The effective sound pressure distribution is reconstructed on the surface of a running vehicle. The method has achieved a high calculation efficiency and is able to quantitatively measure the sound pressure at the sound source and identify the location of the main sound source. The method is also validated by the simulation experiments and the measurement tests with known moving speakers. Finally, the engine noise, tire noise, exhaust noise and wind noise of the vehicle running at different speeds are successfully identified by this method.

Failure mode and effects analysis: a comparison of two common risk prioritisation methods.

PubMed

McElroy, Lisa M; Khorzad, Rebeca; Nannicelli, Anna P; Brown, Alexandra R; Ladner, Daniela P; Holl, Jane L

2016-05-01

Failure mode and effects analysis (FMEA) is a method of risk assessment increasingly used in healthcare over the past decade. The traditional method, however, can require substantial time and training resources. The goal of this study is to compare a simplified scoring method with the traditional scoring method to determine the degree of congruence in identifying high-risk failures. An FMEA of the operating room (OR) to intensive care unit (ICU) handoff was conducted. Failures were scored and ranked using both the traditional risk priority number (RPN) and criticality-based method, and a simplified method, which designates failures as 'high', 'medium' or 'low' risk. The degree of congruence was determined by first identifying those failures determined to be critical by the traditional method (RPN≥300), and then calculating the per cent congruence with those failures designated critical by the simplified methods (high risk). In total, 79 process failures among 37 individual steps in the OR to ICU handoff process were identified. The traditional method yielded Criticality Indices (CIs) ranging from 18 to 72 and RPNs ranging from 80 to 504. The simplified method ranked 11 failures as 'low risk', 30 as medium risk and 22 as high risk. The traditional method yielded 24 failures with an RPN ≥300, of which 22 were identified as high risk by the simplified method (92% agreement). The top 20% of CI (≥60) included 12 failures, of which six were designated as high risk by the simplified method (50% agreement). These results suggest that the simplified method of scoring and ranking failures identified by an FMEA can be a useful tool for healthcare organisations with limited access to FMEA expertise. However, the simplified method does not result in the same degree of discrimination in the ranking of failures offered by the traditional method. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Solving the Capacitive Effect in the High-Frequency sweep for Langmuir Probe in SYMPLE

NASA Astrophysics Data System (ADS)

Pramila; Patel, J. J.; Rajpal, R.; Hansalia, C. J.; Anitha, V. P.; Sathyanarayana, K.

2017-04-01

Langmuir Probe based measurements need to be routinely carried out to measure various plasma parameters such as the electron density (ne), the electron temperature (Te), the floating potential (Vf), and the plasma potential (Vp). For this, the diagnostic electronics along with the biasing power supplies is installed in standard industrial racks with a 2KV isolation transformer. The Signal Conditioning Electronics (SCE) system is populated inside the 4U-chassis based system with the front-end electronics, designed using high common mode differential amplifiers which can measure small differential signal in presence of high common mode dc- bias or ac ramp voltage used for biasing the probes. DC-biasing of the probe is most common method for getting its I-V characteristic but method of biasing the probe with a sweep at high frequency encounters the problem of corruption of signal due to capacitive effect specially when the sweep period and the discharge time is very fast and die down in the order of μs or lesser. This paper presents and summarises the method of removing such effects encountered while measuring the probe current.

Comparing 2 Adhesive Methods on Skin Integrity in the High-Risk Neonate.

PubMed

Boswell, Nicole; Waker, Cheryl L

2016-12-01

Nurses have a primary role in promoting neonatal skin integrity and skin care management of the critically ill neonate. Adhesive products are essential to secure needed medical devices but can be a significant factor contributing to skin breakdown. Current literature does not offer a definitive answer regarding which products most safely and effectively work to secure needed devices in the high-risk neonatal population. To determine which adhesive method is best practice to safely and effectively secure lines/tubes in the high-risk neonate population. The only main effect that was significant was age group with mean skin scores. Subjects in the younger group (24-28 weeks) had higher skin scores than in the older group (28-34 weeks), validating that younger gestations are at higher risk of breakdown with the use of adhesives. The findings did not clearly identify which product was superior to secure tubes and lines, or was the least injurious to skin of the high-risk neonate. Neither a transparent dressing only or transparent dressing over hydrocolloid method clearly demonstrated an advantage in the high-risk, preterm neonate. Anecdotal comments suggested staff preferred the transparent dressing over hydrocolloid method as providing better adhesive while protecting skin integrity. The findings validated that younger gestations are at higher risk of breakdown with the use of adhesives and therefore require close vigilance to maintain skin integrity.

A demonstration of the antimicrobial effectiveness of various copper surfaces

PubMed Central

2013-01-01

Background Bacterial contamination on touch surfaces results in increased risk of infection. In the last few decades, work has been done on the antimicrobial properties of copper and its alloys against a range of micro-organisms threatening public health in food processing, healthcare and air conditioning applications; however, an optimum copper method of surface deposition and mass structure has not been identified. Results A proof-of-concept study of the disinfection effectiveness of three copper surfaces was performed. The surfaces were produced by the deposition of copper using three methods of thermal spray, namely, plasma spray, wire arc spray and cold spray The surfaces were then inoculated with meticillin-resistant Staphylococcus aureus (MRSA). After a two hour exposure to the surfaces, the surviving MRSA were assayed and the results compared. The differences in the copper depositions produced by the three thermal spray methods were examined in order to explain the mechanism that causes the observed differences in MRSA killing efficiencies. The cold spray deposition method was significantly more effective than the other methods. It was determined that work hardening caused by the high velocity particle impacts created by the cold spray technique results in a copper microstructure that enhances ionic diffusion, and copper ions are principally responsible for antimicrobial activity. Conclusions This test showed significant microbiologic differences between coatings produced by different spray techniques and demonstrates the importance of the copper application technique. The cold spray technique shows superior anti-microbial effectiveness caused by the high impact velocity imparted to the sprayed particles which results in high dislocation density and high ionic diffusivity. PMID:23537176

Deterministic ion beam material adding technology for high-precision optical surfaces.

PubMed

Liao, Wenlin; Dai, Yifan; Xie, Xuhui; Zhou, Lin

2013-02-20

Although ion beam figuring (IBF) provides a highly deterministic method for the precision figuring of optical components, several problems still need to be addressed, such as the limited correcting capability for mid-to-high spatial frequency surface errors and low machining efficiency for pit defects on surfaces. We propose a figuring method named deterministic ion beam material adding (IBA) technology to solve those problems in IBF. The current deterministic optical figuring mechanism, which is dedicated to removing local protuberances on optical surfaces, is enriched and developed by the IBA technology. Compared with IBF, this method can realize the uniform convergence of surface errors, where the particle transferring effect generated in the IBA process can effectively correct the mid-to-high spatial frequency errors. In addition, IBA can rapidly correct the pit defects on the surface and greatly improve the machining efficiency of the figuring process. The verification experiments are accomplished on our experimental installation to validate the feasibility of the IBA method. First, a fused silica sample with a rectangular pit defect is figured by using IBA. Through two iterations within only 47.5 min, this highly steep pit is effectively corrected, and the surface error is improved from the original 24.69 nm root mean square (RMS) to the final 3.68 nm RMS. Then another experiment is carried out to demonstrate the correcting capability of IBA for mid-to-high spatial frequency surface errors, and the final results indicate that the surface accuracy and surface quality can be simultaneously improved.

FOEHN: The critical experiment for the Franco-German High Flux Reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scharmer, K.; Eckert, H. G.

1991-01-01

A critical experiment for the Franco-German High Flux Reactor was carried out in the French reactor EOLE (CEN Cadarache). The purpose of the experiment was to check the calculation methods in a realistic geometry and to measure effects that can only be calculated imprecisely (e.g. beam hole effects). The structure of the experiment and the measurement and calculation methods are described. A detailed comparison between theoretical and experimental results was performed. 30 refs., 105 figs.

A parameter identification method for the rotordynamic coefficients of a high Reynolds number hydrostatic bearing

NASA Technical Reports Server (NTRS)

Rouvas, C.; Childs, D. W.

1993-01-01

In identifying the rotordynamic coefficients of a high-Reynolds-number hydrostatic bearing, fluid-flow induced forces present a unique problem, in that they provide an unmeasureable and uncontrollable excitation to the bearing. An analysis method is developed that effectively eliminates the effects of fluid-flow induced excitation on the estimation of the bearing rotordynamic coefficients, by using power spectral densities. In addition to the theoretical development, the method is verified experimentally by single-frequency testing, and repeatability tests. Results obtained for a bearing are the twelve rotordynamic coefficients (stiffness, damping, and inertia coefficients) as functions of eccentricity ratio, speed, and supply pressure.

Oil seal effects and subsynchronous vibrations in high-speed compressors

NASA Technical Reports Server (NTRS)

Allaire, P. E.; Kocur, J. A., Jr.

1985-01-01

Oil seals are commonly used in high speed multistage compressors. If the oil seal ring becomes locked up against the fixed portion of the seal, high oil film crosscoupled stiffnesses can result. A method of analysis for determining if the oil seals are locked up or not is discussed. The method is then applied to an oil seal in a compressor with subsynchronous vibration problems.

Time-frequency domain SNR estimation and its application in seismic data processing

NASA Astrophysics Data System (ADS)

Zhao, Yan; Liu, Yang; Li, Xuxuan; Jiang, Nansen

2014-08-01

Based on an approach estimating frequency domain signal-to-noise ratio (FSNR), we propose a method to evaluate time-frequency domain signal-to-noise ratio (TFSNR). This method adopts short-time Fourier transform (STFT) to estimate instantaneous power spectrum of signal and noise, and thus uses their ratio to compute TFSNR. Unlike FSNR describing the variation of SNR with frequency only, TFSNR depicts the variation of SNR with time and frequency, and thus better handles non-stationary seismic data. By considering TFSNR, we develop methods to improve the effects of inverse Q filtering and high frequency noise attenuation in seismic data processing. Inverse Q filtering considering TFSNR can better solve the problem of amplitude amplification of noise. The high frequency noise attenuation method considering TFSNR, different from other de-noising methods, distinguishes and suppresses noise using an explicit criterion. Examples of synthetic and real seismic data illustrate the correctness and effectiveness of the proposed methods.

Development of an Effective School-Based Financial Management Profile in Malaysia: The Delphi Method Application

ERIC Educational Resources Information Center

Radzi, Norfariza Mohd; Ghani, Muhammad Faizal A.; Siraj, Saedah

2015-01-01

The agenda for national development requires a persistent improvement in education as a tool for creating knowledgeable human capital, highly skilled labour, a high technology society and ultimately a highly civilized nation for the future challenging world. It requires considerable financial and technical investment as well as effective and…

An Investigation of the Life Experiences and Beliefs of High School Teachers Exhibiting Effective Classroom Management Behaviors

ERIC Educational Resources Information Center

Miller, Byron

2012-01-01

The purpose of this qualitative study was to explore the life experiences and beliefs of high school teachers exhibiting highly effective classroom management skills. The research for this phenomenological study utilized the narrative inquiry method of data collection. This study investigates the life experiences and beliefs of nine teachers…

The Impact of Mobility on Student Performance and Teacher Practice

ERIC Educational Resources Information Center

Isernhagen, Jody C.; Bulkin, Nadia

2011-01-01

This article examines the effects that high mobility can have on highly mobile students, non-mobile students, teachers, and schools, with particular focus on the effect of high mobility on academic achievement. A mixed-methods study with data collected from public schools in Nebraska during the 2007-2008 and 2008-2009 school years finds that…

Comparison Between Prospectively Electrocardiogram-Gated High-Pitch Mode and Retrospectively Electrocardiogram-Gated Mode for Dual-Source CT Coronary Angiography.

PubMed

Koplay, Mustafa; Celik, Mahmut; Avcı, Ahmet; Erdogan, Hasan; Demir, Kenan; Sivri, Mesut; Nayman, Alaaddin

2015-01-01

We aimed to report the image quality, relationship between heart rate and image quality, amount of contrast agent given to the patients and radiation doses in coronary CT angiography (CTA) obtained by using high-pitch prospectively ECG-gated "Flash Spiral" technique (method A) or retrospectively ECG-gated technique (method B) using 128×2-slice dual-source CT. A total of 110 patients who were evaluated with method A and method B technique with a 128×2-detector dual-source CT device were included in the study. Patients were divided into three groups based on their heart rates during the procedure, and a relationship between heart rate and image quality were evaluated. The relationship between heart rate, gender and radiation dose received by the patients was compared. A total of 1760 segments were evaluated in terms of image quality. Comparison of the relationship between heart rate and image quality revealed a significant difference between heart rate <60 beats/min group and >75 beats/min group whereas <60 beats/min and 60-75 beats/min groups did not differ significantly. The average effective dose for coronary CTA was calculated as 1.11 mSv (0.47-2.01 mSv) for method A and 8.22 mSv (2.19-12.88 mSv) for method B. Method A provided high quality images with doses as low as <1 mSv in selected patients who have low heart rates with a high negative predictive value to rule out coronary artery disease. Although method B increases the amount of effective dose, it provides high diagnostic quality images for patients who have a high heart rate and arrhythmia which makes it is difficult to obtain images.

Fuzzy Comprehensive Evaluation Method Applied in the Real Estate Investment Risks Research

NASA Astrophysics Data System (ADS)

ML(Zhang Minli), Zhang; Wp(Yang Wenpo), Yang

Real estate investment is a high-risk and high returned of economic activity, the key of real estate analysis is the identification of their types of investment risk and the risk of different types of effective prevention. But, as the financial crisis sweeping the world, the real estate industry also faces enormous risks, how effective and correct evaluation of real estate investment risks becomes the multitudinous scholar concern[1]. In this paper, real estate investment risks were summarized and analyzed, and comparative analysis method is discussed and finally presented fuzzy comprehensive evaluation method, not only in theory has the advantages of science, in the application also has the reliability, for real estate investment risk assessment provides an effective means for investors in real estate investing guidance on risk factors and forecasts.

Simulated Data for High Temperature Composite Design

NASA Technical Reports Server (NTRS)

Chamis, Christos C.; Abumeri, Galib H.

2006-01-01

The paper describes an effective formal method that can be used to simulate design properties for composites that is inclusive of all the effects that influence those properties. This effective simulation method is integrated computer codes that include composite micromechanics, composite macromechanics, laminate theory, structural analysis, and multi-factor interaction model. Demonstration of the method includes sample examples for static, thermal, and fracture reliability for a unidirectional metal matrix composite as well as rupture strength and fatigue strength for a high temperature super alloy. Typical results obtained for a unidirectional composite show that the thermal properties are more sensitive to internal local damage, the longitudinal properties degrade slowly with temperature, the transverse and shear properties degrade rapidly with temperature as do rupture strength and fatigue strength for super alloys.

Analysis and Correction of Diffraction Effect on the B/A Measurement at High Frequencies

NASA Astrophysics Data System (ADS)

Zhang, Dong; Gong, Xiu-Fen; Liu, Xiao-Zhou; Kushibiki, Jun-ichi; Nishino, Hideo

2004-01-01

A numerical method is developed to analyse and to correct the diffraction effect in the measurement of acoustic nonlinearity parameter B/A at high frequencies. By using the KZK nonlinear equation and the superposition approach of Gaussian beams, an analytical model is derived to describe the second harmonic generation through multi-layer medium SiO2/liquid specimen/SiO2. Frequency dependence of the nonlinear characterization curve for water in 110-155 MHz is numerically and experimentally investigated. With the measured dip position and the new model, values of B/A for water are evaluated. The results show that the present method can effectively correct the diffraction effect in the measurement.

Modal Ring Method for the Scattering of Electromagnetic Waves

NASA Technical Reports Server (NTRS)

Baumeister, Kenneth J.; Kreider, Kevin L.

1993-01-01

The modal ring method for electromagnetic scattering from perfectly electric conducting (PEC) symmetrical bodies is presented. The scattering body is represented by a line of finite elements (triangular) on its outer surface. The infinite computational region surrounding the body is represented analytically by an eigenfunction expansion. The modal ring method effectively reduces the two dimensional scattering problem to a one-dimensional problem similar to the method of moments. The modal element method is capable of handling very high frequency scattering because it has a highly banded solution matrix.

Instruction via Web-Based Modules in Early Childhood Personnel Preparation: A Mixed-Methods Study of Effectiveness and Learner Perspectives

ERIC Educational Resources Information Center

Hollingsworth, Heidi L.; Lim, Chih-Ing

2015-01-01

Effective personnel preparation is critical to the development of a high quality early childhood workforce that provides optimal care and education for young children. This mixed-methods study examined the effectiveness of, and learner perspectives on, instruction via web-based modules within face-to-face early childhood personnel preparation…

[Examination of upper abdominal region in high spatial resolution diffusion-weighted imaging using 3-Tesla MRI].

PubMed

Terada, Masaki; Matsushita, Hiroki; Oosugi, Masanori; Inoue, Kazuyasu; Yaegashi, Taku; Anma, Takeshi

2009-03-20

The advantage of the higher signal-to-noise ratio (SNR) of 3-Tesla magnetic resonance imaging (3-Tesla) has the possibility of contributing to the improvement of high spatial resolution without causing image deterioration. In this study, we compared SNR and the apparent diffusion coefficient (ADC) value with 3-Tesla as the condition in the diffusion-weighted image (DWI) parameter of the 1.5-Tesla magnetic resonance imaging (1.5-Tesla) and we examined the high spatial resolution images in the imaging method [respiratory-triggering (RT) method and breath free (BF) method] and artifact (motion and zebra) in the upper abdominal region of DWI at 3-Tesla. We have optimized scan parameters based on phantom and in vivo study. As a result, 3-Tesla was able to obtain about 1.5 times SNR in comparison with the 1.5-Tesla, ADC value had few differences. Moreover, the RT method was effective in correcting the influence of respiratory movement in comparison with the BF method, and image improvement by the effective acquisition of SNR and reduction of the artifact were provided. Thus, DWI of upper abdominal region was a useful sequence for the high spatial resolution in 3-Tesla.

The Effect of Communication Skills Training by Video Feedback Method on Clinical Skills of Interns of Isfahan University of Medical Sciences Compared to Didactic Methods

ERIC Educational Resources Information Center

Managheb, S. E.; Zamani, A.; Shams, B.; Farajzadegan, Z.

2012-01-01

Background: Effective communication is essential to the practice of high-quality medicine. There are methodological challenges in communication skills training. This study was performed in order to assess the educational benefits of communication skills training by video feedback method versus traditional formats such as lectures on clinical…

Effects of Manufacturing Methods on Dissolution and Absorption of Ketoconazole in the Presence of Organic Acid as a pH Modifier.

PubMed

Adachi, Masashi; Hinatsu, Yuta; Kusamori, Kosuke; Katsumi, Hidemasa; Sakane, Toshiyasu; Nakatani, Manabu; Wada, Koichi; Yamamoto, Akira

2017-05-01

Poorly water-soluble compounds have a potential risk of low and variable bioavailability caused by incomplete dissolution. Incorporation of organic acids as pH modifiers is effective method for solubility enhancement of basic compounds and requires no special technique and equipment. The purpose of this study was to evaluate the effect of manufacturing method on the extent of drug solubility enhancement. We successfully prepared the granules and tablets containing ketoconazole (KZ), which is weakly basic, as a model compound and citric acid as a pH modifier using conventional wet and dry granulations. KZ solubility under non-sink condition was enhanced with supersaturation using both wet and dry granulations. High-shear granulation was the most effective method in terms of KZ dissolution enhancement, because both an intimate contact and strong bonding between KZ and incorporated acid were achieved. KZ dissolved amount from the granules prepared by high-shear granulation was about eight times higher than that from the granules without the acid. The granulation involved to suppress a diffusion of acid dissolved, leading to the effectively maintained supersaturation state. The bioavailability of KZ after oral administration to rats was improved by applying high-shear granulation with citric acid independent of gastrointestinal pH. The granules prepared by high-shear granulation showed the bioavailability about 1.7-fold higher than that of the physical mixture in rats with and without neutralization of stomach. As a result, both the dissolution and absorption rates of KZ after oral administration were enhanced using conventional manufacturing technology.

Self-Explanation in the Domain of Statistics: An Expertise Reversal Effect

ERIC Educational Resources Information Center

Leppink, Jimmie; Broers, Nick J.; Imbos, Tjaart; van der Vleuten, Cees P. M.; Berger, Martijn P. F.

2012-01-01

This study investigated the effects of four instructional methods on cognitive load, propositional knowledge, and conceptual understanding of statistics, for low prior knowledge students and for high prior knowledge students. The instructional methods were (1) a reading-only control condition, (2) answering open-ended questions, (3) answering…

An Effective Method for Detecting Potential Woodland Vernal Pools Using High-Resolution LiDAR Data and Aerial Imagery

EPA Science Inventory

Effective conservation of woodland vernal pools – important components of regional amphibian diversity and ecosystem services – depends on locating and mapping these pools accurately. Current methods for identifying potential vernal pools are primarily based on visual interpretat...

Investigation of synergistic effects of warm mix asphalt and high fractionated reclaimed asphalt for safe, environmentally sustainable highway.

DOT National Transportation Integrated Search

2013-11-01

To increase RAP materials by up to 75% by binder replacement, a fractionation method was applied to the RAP stockpile by : discarding RAP materials passing No. 16 sieve. This fractionation method was effective in improving volumetric properties : of ...

Study on photoelectric parameter measurement method of high capacitance solar cell

NASA Astrophysics Data System (ADS)

Zhang, Junchao; Xiong, Limin; Meng, Haifeng; He, Yingwei; Cai, Chuan; Zhang, Bifeng; Li, Xiaohui; Wang, Changshi

2018-01-01

The high efficiency solar cells usually have high capacitance characteristic, so the measurement of their photoelectric performance usually requires long pulse width and long sweep time. The effects of irradiance non-uniformity, probe shielding and spectral mismatch on the IV curve measurement are analyzed experimentally. A compensation method for irradiance loss caused by probe shielding is proposed, and the accurate measurement of the irradiance intensity in the IV curve measurement process of solar cell is realized. Based on the characteristics that the open circuit voltage of solar cell is sensitive to the junction temperature, an accurate measurement method of the temperature of solar cell under continuous irradiation condition is proposed. Finally, a measurement method with the characteristic of high accuracy and wide application range for high capacitance solar cell is presented.

Unmet Demand for Highly Effective Postpartum Contraception in Texas

PubMed Central

Potter, Joseph E.; Hopkins, Kristine; Aiken, Abigail R. A.; Lopez, Celia Hubert; Stevenson, Amanda J.; White, Kari; Grossman, Daniel

2014-01-01

Objectives We aimed to assess women's contraceptive preferences and use in the first 6 months after delivery. The postpartum period represents a key opportunity for women to learn about and obtain effective contraception, especially since 50% of unintended pregnancies to parous women occur within 2 years of a previous birth. Methods We conducted a prospective cohort study of 800 postpartum women recruited from three hospitals in Austin and El Paso, TX. Women aged 18–44 who wanted to delay childbearing for at least 24 months were eligible for the study and completed interviews following delivery and at 3 and 6 months postpartum. Participants were asked about the contraceptive method they were currently using and the method they would prefer to use at 6 months after delivery. Results At 6 months postpartum, 13% of women were using an IUD or implant, and 17% were sterilized or had a partner who had had a vasectomy. Twenty-four percent were using hormonal methods, and 45% relied on less effective methods, mainly condoms and withdrawal. Yet 44% reported that they would prefer to be using sterilization, and 34% would prefer to be using LARC. Conclusions This study shows a considerable preference for LARC and permanent methods at six months postpartum. However, there is a marked discordance between women's method preference and actual use, indicating substantial unmet demand for highly effective methods of contraception. PMID:25129329

A Robust Method of Measuring Other-Race and Other-Ethnicity Effects: The Cambridge Face Memory Test Format

PubMed Central

McKone, Elinor; Stokes, Sacha; Liu, Jia; Cohan, Sarah; Fiorentini, Chiara; Pidcock, Madeleine; Yovel, Galit; Broughton, Mary; Pelleg, Michel

2012-01-01

Other-race and other-ethnicity effects on face memory have remained a topic of consistent research interest over several decades, across fields including face perception, social psychology, and forensic psychology (eyewitness testimony). Here we demonstrate that the Cambridge Face Memory Test format provides a robust method for measuring these effects. Testing the Cambridge Face Memory Test original version (CFMT-original; European-ancestry faces from Boston USA) and a new Cambridge Face Memory Test Chinese (CFMT-Chinese), with European and Asian observers, we report a race-of-face by race-of-observer interaction that was highly significant despite modest sample size and despite observers who had quite high exposure to the other race. We attribute this to high statistical power arising from the very high internal reliability of the tasks. This power also allows us to demonstrate a much smaller within-race other ethnicity effect, based on differences in European physiognomy between Boston faces/observers and Australian faces/observers (using the CFMT-Australian). PMID:23118912

Regional Diversity and Diversification in Mammals.

PubMed

Machac, Antonin; Graham, Catherine H

2017-01-01

The effects of regional diversity on diversification remain controversial. The classic hypothesis that diversification decelerates as regional diversity increases has been recently revived. Yet, there is little geographic evidence for slower diversification across regions of high diversity, and diversity is often thought to promote diversification through its effects on ecological divergence and speciation. Here, we use the newest phylogeny for mammals (4,990 species) and two different methods to test the effects of regional diversity on diversification. We find that regions of high diversity are dominated by expanding clades that are far from their estimated carrying capacities. Regions of low diversity host clades that are small and mostly saturated. These results were supported across mammals and their six largest orders. They were corroborated by the two methods when controlling for clade relatedness, clade nestedness, and clade size. Together, these results reject the hypothesis that high geographic concentration of mammals effectively suppresses their further diversification. Instead, highly diverse regions (especially the tropics) seem to act as the engine of mammalian richness.

Oil leakage detection for electric power equipment based on ultraviolet fluorescence effect

NASA Astrophysics Data System (ADS)

Zhang, Jing; Wang, Jian-hui; Xu, Bin; Huang, Zhi-dong; Huang, Lan-tao

2018-03-01

This paper presents a method to detect the oil leakage of high voltage power equipment based on ultraviolet fluorescence effect. The method exploits the principle that the insulating oil has the fluorescent effect under the irradiation of specific ultraviolet light. The emission spectrum of insulating oil under excitation light with different wavelengths is measured and analyzed first. On this basis, a portable oil leakage detective device for high voltage power equipment is designed and developed with a selected 365 nm ultraviolet as the excitation light and the low light level camera as the fluorescence image collector. Then, the feasibility of the proposed method and device in different conditions is experimentally verified in the laboratory environment. Finally, the developed oil leakage detective device is applied to 500 kV Xiamen substation and Quanzhou substation. And the results show that the device can detect the oil leakage of high voltage electrical equipment quickly and conveniently even under the condition of a slight oil leakage especially in the low light environment.

High-Temperature-Short-Time Annealing Process for High-Performance Large-Area Perovskite Solar Cells.

PubMed

Kim, Minjin; Kim, Gi-Hwan; Oh, Kyoung Suk; Jo, Yimhyun; Yoon, Hyun; Kim, Ka-Hyun; Lee, Heon; Kim, Jin Young; Kim, Dong Suk

2017-06-27

Organic-inorganic hybrid metal halide perovskite solar cells (PSCs) are attracting tremendous research interest due to their high solar-to-electric power conversion efficiency with a high possibility of cost-effective fabrication and certified power conversion efficiency now exceeding 22%. Although many effective methods for their application have been developed over the past decade, their practical transition to large-size devices has been restricted by difficulties in achieving high performance. Here we report on the development of a simple and cost-effective production method with high-temperature and short-time annealing processing to obtain uniform, smooth, and large-size grain domains of perovskite films over large areas. With high-temperature short-time annealing at 400 °C for 4 s, the perovskite film with an average domain size of 1 μm was obtained, which resulted in fast solvent evaporation. Solar cells fabricated using this processing technique had a maximum power conversion efficiency exceeding 20% over a 0.1 cm 2 active area and 18% over a 1 cm 2 active area. We believe our approach will enable the realization of highly efficient large-area PCSs for practical development with a very simple and short-time procedure. This simple method should lead the field toward the fabrication of uniform large-scale perovskite films, which are necessary for the production of high-efficiency solar cells that may also be applicable to several other material systems for more widespread practical deployment.

Comparison effectiveness of cooperative learning type STAD with cooperative learning type TPS in terms of mathematical method of Junior High School students

NASA Astrophysics Data System (ADS)

Wahyuni, A.

2018-05-01

This research is aimed to find out whether the model of cooperative learning type Student Team Achievement Division (STAD) is more effective than cooperative learning type Think-Pair-Share in SMP Negeri 7 Yogyakarta. This research was a quasi-experimental research, using two experimental groups. The population of research was all students of 7thclass in SMP Negeri 7 Yogyakarta that consists of 5 Classes. From the population were taken 2 classes randomly which used as sample. The instrument to collect data was a description test. Measurement of instrument validity use content validity and construct validity, while measuring instrument reliability use Cronbach Alpha formula. To investigate the effectiveness of cooperative learning type STAD and cooperative learning type TPS on the aspect of student’s mathematical method, the datas were analyzed by one sample test. Comparing the effectiveness of cooperative learning type STAD and TPS in terms of mathematical communication skills by using t-test. Normality test was not conducted because the sample of research more than 30 students, while homogeneity tested by using Kolmogorov Smirnov test. The analysis was performed at 5% confidence level.The results show as follows : 1) The model of cooperative learning type STAD and TPS are effective in terms of mathematical method of junior high school students. 2). STAD type cooperative learning model is more effective than TPS type cooperative learning model in terms of mathematical methods of junior high school students.

Protecting against both pregnancy and disease: predictors of dual method use among a sample of women.

PubMed

Harvey, S Marie; Henderson, Jillian T; Branch, Meredith Roberts

2004-01-01

Although male condoms are the best form of protection against HIV/STDs, they are not the most effective method for preventing unintended pregnancy. Consequently, use of condoms and a highly effective contraceptive-referred to as dual use-is recommended as the optimal protection against both disease and pregnancy. However, little is known about the factors that promote dual use. This study examined associations of dual method use with women's background characteristics, intrapersonal factors, and relationship characteristics. Data are from a random sample of women selected from a large managed care organization in the Pacific Northwest. The analytic sample contained 371 women who completed a telephone survey and reported use of contraceptives in the past 3 months. Three mutually exclusive method use groups were constructed: effective contraceptive only (hormonal methods, intrauterine device, surgical sterilization) (59%), condom only (24%), and dual use (18%). Variables hypothesized to influence dual use were compared across the three groups in bivariate and multivariate analyses. Findings indicate that women who were younger, reported more than one sexual partner in the past year, and were highly motivated to avoid HIV/STDs--were more likely to use dual methods rather than condoms only or an effective contraceptive method. Women confident about using condoms without feeling embarrassed or breaking the sexual mood were more likely to use dual methods rather than a single effective method. Finally, women with confidence in their ability to use condoms correctly are more likely to rely solely on condoms. Policy and practice implications are discussed.

High-Modulation-Speed LEDs Based on III-Nitride

NASA Astrophysics Data System (ADS)

Chen, Hong

III-nitride InGaN light-emitting diodes (LEDs) enable wide range of applications in solid-state lighting, full-color displays, and high-speed visible-light communication. Conventional InGaN quantum well LEDs grown on polar c-plane substrate suffer from quantum confined Stark effect due to the large internal polarization-related fields, leading to a reduced radiative recombination rate and device efficiency, which limits the performance of InGaN LEDs in high-speed communication applications. To circumvent these negative effects, non-trivial-cavity designs such as flip-chip LEDs, metallic grating coated LEDs are proposed. This oral defense will show the works on the high-modulation-speed LEDs from basic ideas to applications. Fundamental principles such as rate equations for LEDs/laser diodes (LDs), plasmonic effects, Purcell effects will be briefly introduced. For applications, the modal properties of flip-chip LEDs are solved by implementing finite difference method in order to study the modulation response. The emission properties of highly polarized InGaN LEDs coated by metallic gratings are also investigated by finite difference time domain method.

Case-Study of the High School Student's Family Values Formation

ERIC Educational Resources Information Center

Valeeva, Roza A.; Korolyeva, Natalya E.; Sakhapova, Farida Kh.

2016-01-01

The aim of the research is the theoretical justification and experimental verification of content, complex forms and methods to ensure effective development of the high school students' family values formation. 93 lyceum students from Kazan took part in the experiment. To study students' family values we have applied method of studying personality…

Conducting High Cycle Fatigue Strength Step Tests on Gamma TiAl

NASA Technical Reports Server (NTRS)

Lerch, Brad; Draper, Sue; Pereira, J. Mike

2002-01-01

High cycle fatigue strength testing of gamma TiAl by the step test method is investigated. A design of experiments was implemented to determine if the coaxing effect occurred during testing. Since coaxing was not observed, step testing was deemed a suitable method to define the fatigue strength at 106 cycles.

Some Factors That Affecting the Performance of Mathematics Teachers in Junior High School in Medan

ERIC Educational Resources Information Center

Manullang, Martua; Rajagukguk, Waminton

2016-01-01

Some Factor's That Affecting The Mathematic Teacher Performance For Junior High School In Medan. This research will examine the effect of direct and indirect of the Organizational Knowledge towards the achievement motivation, decision making, organizational commitment, the performance of mathematics teacher. The research method is a method of…

Drying of Pigment-Cellulose Nanofibril Substrates

PubMed Central

Timofeev, Oleg; Torvinen, Katariina; Sievänen, Jenni; Kaljunen, Timo; Kouko, Jarmo; Ketoja, Jukka A.

2014-01-01

A new substrate containing cellulose nanofibrils and inorganic pigment particles has been developed for printed electronics applications. The studied composite structure contains 80% fillers and is mechanically stable and flexible. Before drying, the solids content can be as low as 20% due to the high water binding capacity of the cellulose nanofibrils. We have studied several drying methods and their effects on the substrate properties. The aim is to achieve a tight, smooth surface keeping the drying efficiency simultaneously at a high level. The methods studied include: (1) drying on a hot metal surface; (2) air impingement drying; and (3) hot pressing. Somewhat surprisingly, drying rates measured for the pigment-cellulose nanofibril substrates were quite similar to those for the reference board sheets. Very high dewatering rates were observed for the hot pressing at high moisture contents. The drying method had significant effects on the final substrate properties, especially on short-range surface smoothness. The best smoothness was obtained with a combination of impingement and contact drying. The mechanical properties of the sheets were also affected by the drying method and associated temperature. PMID:28788220

Proximity correction of high-dosed frame with PROXECCO

NASA Astrophysics Data System (ADS)

Eisenmann, Hans; Waas, Thomas; Hartmann, Hans

1994-05-01

Usefulness of electron beam lithography is strongly related to the efficiency and quality of methods used for proximity correction. This paper addresses the above issue by proposing an extension to the new proximity correction program PROXECCO. The combination of a framing step with PROXECCO produces a pattern with a very high edge accuracy and still allows usage of the fast correction procedure. Making a frame with a higher dose imitates a fine resolution correction where the coarse part is disregarded. So after handling the high resolution effect by means of framing, an additional coarse correction is still needed. Higher doses have a higher contribution to the proximity effect. This additional proximity effect is taken into account with the help of the multi-dose input of PROXECCO. The dose of the frame is variable, depending on the deposited energy coming from backscattering of the proximity. Simulation proves the very high edge accuracy of the applied method.

Advanced Fabrication Method for the Preparation of MOF Thin Films: Liquid-Phase Epitaxy Approach Meets Spin Coating Method.

PubMed

Chernikova, Valeriya; Shekhah, Osama; Eddaoudi, Mohamed

2016-08-10

Here, we report a new and advanced method for the fabrication of highly oriented/polycrystalline metal-organic framework (MOF) thin films. Building on the attractive features of the liquid-phase epitaxy (LPE) approach, a facile spin coating method was implemented to generate MOF thin films in a high-throughput fashion. Advantageously, this approach offers a great prospective to cost-effectively construct thin-films with a significantly shortened preparation time and a lessened chemicals and solvents consumption, as compared to the conventional LPE-process. Certainly, this new spin-coating approach has been implemented successfully to construct various MOF thin films, ranging in thickness from a few micrometers down to the nanometer scale, spanning 2-D and 3-D benchmark MOF materials including Cu2(bdc)2·xH2O, Zn2(bdc)2·xH2O, HKUST-1, and ZIF-8. This method was appraised and proved effective on a variety of substrates comprising functionalized gold, silicon, glass, porous stainless steel, and aluminum oxide. The facile, high-throughput and cost-effective nature of this approach, coupled with the successful thin film growth and substrate versatility, represents the next generation of methods for MOF thin film fabrication. Therefore, paving the way for these unique MOF materials to address a wide range of challenges in the areas of sensing devices and membrane technology.

Tracking of Indels by DEcomposition is a Simple and Effective Method to Assess Efficiency of Guide RNAs in Zebrafish.

PubMed

Etard, Christelle; Joshi, Swarnima; Stegmaier, Johannes; Mikut, Ralf; Strähle, Uwe

2017-12-01

A bottleneck in CRISPR/Cas9 genome editing is variable efficiencies of in silico-designed gRNAs. We evaluated the sensitivity of the TIDE method (Tracking of Indels by DEcomposition) introduced by Brinkman et al. in 2014 for assessing the cutting efficiencies of gRNAs in zebrafish. We show that this simple method, which involves bulk polymerase chain reaction amplification and Sanger sequencing, is highly effective in tracking well-performing gRNAs in pools of genomic DNA derived from injected embryos. The method is equally effective for tracing INDELs in heterozygotes.

Detecting and removing multiplicative spatial bias in high-throughput screening technologies.

PubMed

Caraus, Iurie; Mazoure, Bogdan; Nadon, Robert; Makarenkov, Vladimir

2017-10-15

Considerable attention has been paid recently to improve data quality in high-throughput screening (HTS) and high-content screening (HCS) technologies widely used in drug development and chemical toxicity research. However, several environmentally- and procedurally-induced spatial biases in experimental HTS and HCS screens decrease measurement accuracy, leading to increased numbers of false positives and false negatives in hit selection. Although effective bias correction methods and software have been developed over the past decades, almost all of these tools have been designed to reduce the effect of additive bias only. Here, we address the case of multiplicative spatial bias. We introduce three new statistical methods meant to reduce multiplicative spatial bias in screening technologies. We assess the performance of the methods with synthetic and real data affected by multiplicative spatial bias, including comparisons with current bias correction methods. We also describe a wider data correction protocol that integrates methods for removing both assay and plate-specific spatial biases, which can be either additive or multiplicative. The methods for removing multiplicative spatial bias and the data correction protocol are effective in detecting and cleaning experimental data generated by screening technologies. As our protocol is of a general nature, it can be used by researchers analyzing current or next-generation high-throughput screens. The AssayCorrector program, implemented in R, is available on CRAN. makarenkov.vladimir@uqam.ca. Supplementary data are available at Bioinformatics online. © The Author (2017). Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com

A Fast and Effective Microfluidic Spraying-Plunging Method for High-Resolution Single-Particle Cryo-EM.

PubMed

Feng, Xiangsong; Fu, Ziao; Kaledhonkar, Sandip; Jia, Yuan; Shah, Binita; Jin, Amy; Liu, Zheng; Sun, Ming; Chen, Bo; Grassucci, Robert A; Ren, Yukun; Jiang, Hongyuan; Frank, Joachim; Lin, Qiao

2017-04-04

We describe a spraying-plunging method for preparing cryoelectron microscopy (cryo-EM) grids with vitreous ice of controllable, highly consistent thickness using a microfluidic device. The new polydimethylsiloxane (PDMS)-based sprayer was tested with apoferritin. We demonstrate that the structure can be solved to high resolution with this method of sample preparation. Besides replacing the conventional pipetting-blotting-plunging method, one of many potential applications of the new sprayer is in time-resolved cryo-EM, as part of a PDMS-based microfluidic reaction channel to study short-lived intermediates on the timescale of 10-1,000 ms. Published by Elsevier Ltd.

Evaluation and Comparison of the Processing Methods of Airborne Gravimetry Concerning the Errors Effects on Downward Continuation Results: Case Studies in Louisiana (USA) and the Tibetan Plateau (China).

PubMed

Zhao, Qilong; Strykowski, Gabriel; Li, Jiancheng; Pan, Xiong; Xu, Xinyu

2017-05-25

Gravity data gaps in mountainous areas are nowadays often filled in with the data from airborne gravity surveys. Because of the errors caused by the airborne gravimeter sensors, and because of rough flight conditions, such errors cannot be completely eliminated. The precision of the gravity disturbances generated by the airborne gravimetry is around 3-5 mgal. A major obstacle in using airborne gravimetry are the errors caused by the downward continuation. In order to improve the results the external high-accuracy gravity information e.g., from the surface data can be used for high frequency correction, while satellite information can be applying for low frequency correction. Surface data may be used to reduce the systematic errors, while regularization methods can reduce the random errors in downward continuation. Airborne gravity surveys are sometimes conducted in mountainous areas and the most extreme area of the world for this type of survey is the Tibetan Plateau. Since there are no high-accuracy surface gravity data available for this area, the above error minimization method involving the external gravity data cannot be used. We propose a semi-parametric downward continuation method in combination with regularization to suppress the systematic error effect and the random error effect in the Tibetan Plateau; i.e., without the use of the external high-accuracy gravity data. We use a Louisiana airborne gravity dataset from the USA National Oceanic and Atmospheric Administration (NOAA) to demonstrate that the new method works effectively. Furthermore, and for the Tibetan Plateau we show that the numerical experiment is also successfully conducted using the synthetic Earth Gravitational Model 2008 (EGM08)-derived gravity data contaminated with the synthetic errors. The estimated systematic errors generated by the method are close to the simulated values. In addition, we study the relationship between the downward continuation altitudes and the error effect. The analysis results show that the proposed semi-parametric method combined with regularization is efficient to address such modelling problems.

Evaluation and Comparison of the Processing Methods of Airborne Gravimetry Concerning the Errors Effects on Downward Continuation Results: Case Studies in Louisiana (USA) and the Tibetan Plateau (China)

PubMed Central

Zhao, Qilong; Strykowski, Gabriel; Li, Jiancheng; Pan, Xiong; Xu, Xinyu

2017-01-01

Gravity data gaps in mountainous areas are nowadays often filled in with the data from airborne gravity surveys. Because of the errors caused by the airborne gravimeter sensors, and because of rough flight conditions, such errors cannot be completely eliminated. The precision of the gravity disturbances generated by the airborne gravimetry is around 3–5 mgal. A major obstacle in using airborne gravimetry are the errors caused by the downward continuation. In order to improve the results the external high-accuracy gravity information e.g., from the surface data can be used for high frequency correction, while satellite information can be applying for low frequency correction. Surface data may be used to reduce the systematic errors, while regularization methods can reduce the random errors in downward continuation. Airborne gravity surveys are sometimes conducted in mountainous areas and the most extreme area of the world for this type of survey is the Tibetan Plateau. Since there are no high-accuracy surface gravity data available for this area, the above error minimization method involving the external gravity data cannot be used. We propose a semi-parametric downward continuation method in combination with regularization to suppress the systematic error effect and the random error effect in the Tibetan Plateau; i.e., without the use of the external high-accuracy gravity data. We use a Louisiana airborne gravity dataset from the USA National Oceanic and Atmospheric Administration (NOAA) to demonstrate that the new method works effectively. Furthermore, and for the Tibetan Plateau we show that the numerical experiment is also successfully conducted using the synthetic Earth Gravitational Model 2008 (EGM08)-derived gravity data contaminated with the synthetic errors. The estimated systematic errors generated by the method are close to the simulated values. In addition, we study the relationship between the downward continuation altitudes and the error effect. The analysis results show that the proposed semi-parametric method combined with regularization is efficient to address such modelling problems. PMID:28587086

Evaluation and Comparison of the Processing Methods of Airborne Gravimetry Concerning the Errors Effects on Downward Continuation Results: Case Studies in Louisiana (USA) and the Tibetan Plateau (China)

NASA Astrophysics Data System (ADS)

Zhao, Q.

2017-12-01

Gravity data gaps in mountainous areas are nowadays often filled in with the data from airborne gravity surveys. Because of the errors caused by the airborne gravimeter sensors, and because of rough flight conditions, such errors cannot be completely eliminated. The precision of the gravity disturbances generated by the airborne gravimetry is around 3-5 mgal. A major obstacle in using airborne gravimetry are the errors caused by the downward continuation. In order to improve the results the external high-accuracy gravity information e.g., from the surface data can be used for high frequency correction, while satellite information can be applying for low frequency correction. Surface data may be used to reduce the systematic errors, while regularization methods can reduce the random errors in downward continuation. Airborne gravity surveys are sometimes conducted in mountainous areas and the most extreme area of the world for this type of survey is the Tibetan Plateau. Since there are no high-accuracy surface gravity data available for this area, the above error minimization method involving the external gravity data cannot be used. We propose a semi-parametric downward continuation method in combination with regularization to suppress the systematic error effect and the random error effect in the Tibetan Plateau; i.e., without the use of the external high-accuracy gravity data. We use a Louisiana airborne gravity dataset from the USA National Oceanic and Atmospheric Administration (NOAA) to demonstrate that the new method works effectively. Furthermore, and for the Tibetan Plateau we show that the numerical experiment is also successfully conducted using the synthetic Earth Gravitational Model 2008 (EGM08)-derived gravity data contaminated with the synthetic errors. The estimated systematic errors generated by the method are close to the simulated values. In addition, we study the relationship between the downward continuation altitudes and the error effect. The analysis results show that the proposed semi-parametric method combined with regularization is efficient to address such modelling problems.

[Medical Equipment Maintenance Methods].

PubMed

Liu, Hongbin

2015-09-01

Due to the high technology and the complexity of medical equipment, as well as to the safety and effectiveness, it determines the high requirements of the medical equipment maintenance work. This paper introduces some basic methods of medical instrument maintenance, including fault tree analysis, node method and exclusive method which are the three important methods in the medical equipment maintenance, through using these three methods for the instruments that have circuit drawings, hardware breakdown maintenance can be done easily. And this paper introduces the processing methods of some special fault conditions, in order to reduce little detours in meeting the same problems. Learning is very important for stuff just engaged in this area.

High-quality compressive ghost imaging

NASA Astrophysics Data System (ADS)

Huang, Heyan; Zhou, Cheng; Tian, Tian; Liu, Dongqi; Song, Lijun

2018-04-01

We propose a high-quality compressive ghost imaging method based on projected Landweber regularization and guided filter, which effectively reduce the undersampling noise and improve the resolution. In our scheme, the original object is reconstructed by decomposing of regularization and denoising steps instead of solving a minimization problem in compressive reconstruction process. The simulation and experimental results show that our method can obtain high ghost imaging quality in terms of PSNR and visual observation.

Read count-based method for high-throughput allelic genotyping of transposable elements and structural variants.

PubMed

Kuhn, Alexandre; Ong, Yao Min; Quake, Stephen R; Burkholder, William F

2015-07-08

Like other structural variants, transposable element insertions can be highly polymorphic across individuals. Their functional impact, however, remains poorly understood. Current genome-wide approaches for genotyping insertion-site polymorphisms based on targeted or whole-genome sequencing remain very expensive and can lack accuracy, hence new large-scale genotyping methods are needed. We describe a high-throughput method for genotyping transposable element insertions and other types of structural variants that can be assayed by breakpoint PCR. The method relies on next-generation sequencing of multiplex, site-specific PCR amplification products and read count-based genotype calls. We show that this method is flexible, efficient (it does not require rounds of optimization), cost-effective and highly accurate. This method can benefit a wide range of applications from the routine genotyping of animal and plant populations to the functional study of structural variants in humans.

Effect of synthesis methods with different annealing temperatures on micro structure, cations distribution and magnetic properties of nano-nickel ferrite

NASA Astrophysics Data System (ADS)

El-Sayed, Karimat; Mohamed, Mohamed Bakr; Hamdy, Sh.; Ata-Allah, S. S.

2017-02-01

Nano-crystalline NiFe2O4 was synthesized by citrate and sol-gel methods at different annealing temperatures and the results were compared with a bulk sample prepared by ceramic method. The effect of methods of preparation and different annealing temperatures on the crystallize size, strain, bond lengths, bond angles, cations distribution and degree of inversions were investigated by X-ray powder diffraction, high resolution transmission electron microscope, Mössbauer effect spectrometer and vibrating sample magnetometer. The cations distributions were determined at both octahedral and tetrahedral sites using both Mössbauer effect spectroscopy and a modified Bertaut method using Rietveld method. The Mössbauer effect spectra showed a regular decrease in the hyperfine field with decreasing particle size. Saturation magnetization and coercivity are found to be affected by the particle size and the cations distribution.

Application of High-Resolution Magic-Angle Spinning NMR Spectroscopy to Define the Cell Uptake of MRI Contrast Agents

NASA Astrophysics Data System (ADS)

Calabi, Luisella; Alfieri, Goffredo; Biondi, Luca; De Miranda, Mario; Paleari, Lino; Ghelli, Stefano

2002-06-01

A new method, based on proton high-resolution magic-angle spinning ( 1H HR-MAS) NMR spectroscopy, has been employed to study the cell uptake of magnetic resonance imaging contrast agents (MRI-CAs). The method was tested on human red blood cells (HRBC) and white blood cells (HWBC) by using three gadolinium complexes, widely used in diagnostics, Gd-BOPTA, Gd-DTPA, and Gd-DOTA, and the analogous complexes obtained by replacing Gd(III) with Dy(III), Nd(III), and Tb(III) (i.e., complexes isostructural to the ones of gadolinium but acting as shift agents). The method is based on the evaluation of the magnetic effects, line broadening, or induced lanthanide shift (LIS) caused by these complexes on NMR signals of intra- and extracellular water. Since magnetic effects are directly linked to permeability, this method is direct. In all the tests, these magnetic effects were detected for the extracellular water signal only, providing a direct proof that these complexes are not able to cross the cell membrane. Line broadening effects (i.e., the use of gadolinium complexes) only allow qualitative evaluations. On the contrary, LIS effects can be measured with high precision and they can be related to the concentration of the paramagnetic species in the cellular compartments. This is possible because the HR-MAS technique provides the complete elimination of bulk magnetic susceptibility (BMS) shift and the differentiation of extra- and intracellular water signals. Thus with this method, the rapid quantification of the MRI-CA amount inside and outside the cells is actually feasible.

Physical therapy methods in the treatment and rehabilitation of cancer patients

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kucherova, T. Ya., E-mail: nii@oncology.tomsk.ru; Choinzonov, E. L., E-mail: nii@oncology.tomsk.ru; Tuzikov, S. A., E-mail: TuzikovSA@oncology.tomsk.ru

The results of the effective use of magnetic laser therapy in the treatment and rehabilitation of cancer patients were presented. The effect of magnetic-laser therapy in the treatment of radiation-induced reactions in the patients with head and neck cancer and in the patients with breast cancer was analyzed. High efficiency of lymphedema and lymphorrhea treatment in the postoperative period in the patients with breast cancer was proved. The results of rehabilitation of the patients with gastric cancer after surgical treatment were presented. These data indicate a high effectiveness of different physical methods of treatment and rehabilitation of cancer patients.

Physical therapy methods in the treatment and rehabilitation of cancer patients

NASA Astrophysics Data System (ADS)

Kucherova, T. Ya.; Velikaya, V. V.; Gribova, O. V.; Startseva, Zh. A.; Choinzonov, E. L.; Tuzikov, S. A.; Vusik, M. V.; Doroshenko, A. V.

2016-08-01

The results of the effective use of magnetic laser therapy in the treatment and rehabilitation of cancer patients were presented. The effect of magnetic-laser therapy in the treatment of radiation-induced reactions in the patients with head and neck cancer and in the patients with breast cancer was analyzed. High efficiency of lymphedema and lymphorrhea treatment in the postoperative period in the patients with breast cancer was proved. The results of rehabilitation of the patients with gastric cancer after surgical treatment were presented. These data indicate a high effectiveness of different physical methods of treatment and rehabilitation of cancer patients.

Multi-focus image fusion algorithm using NSCT and MPCNN

NASA Astrophysics Data System (ADS)

Liu, Kang; Wang, Lianli

2018-04-01

Based on nonsubsampled contourlet transform (NSCT) and modified pulse coupled neural network (MPCNN), the paper proposes an effective method of image fusion. Firstly, the paper decomposes the source image into the low-frequency components and high-frequency components using NSCT, and then processes the low-frequency components by regional statistical fusion rules. For high-frequency components, the paper calculates the spatial frequency (SF), which is input into MPCNN model to get relevant coefficients according to the fire-mapping image of MPCNN. At last, the paper restructures the final image by inverse transformation of low-frequency and high-frequency components. Compared with the wavelet transformation (WT) and the traditional NSCT algorithm, experimental results indicate that the method proposed in this paper achieves an improvement both in human visual perception and objective evaluation. It indicates that the method is effective, practical and good performance.

Effective data validation of high-frequency data: time-point-, time-interval-, and trend-based methods.

PubMed

Horn, W; Miksch, S; Egghart, G; Popow, C; Paky, F

1997-09-01

Real-time systems for monitoring and therapy planning, which receive their data from on-line monitoring equipment and computer-based patient records, require reliable data. Data validation has to utilize and combine a set of fast methods to detect, eliminate, and repair faulty data, which may lead to life-threatening conclusions. The strength of data validation results from the combination of numerical and knowledge-based methods applied to both continuously-assessed high-frequency data and discontinuously-assessed data. Dealing with high-frequency data, examining single measurements is not sufficient. It is essential to take into account the behavior of parameters over time. We present time-point-, time-interval-, and trend-based methods for validation and repair. These are complemented by time-independent methods for determining an overall reliability of measurements. The data validation benefits from the temporal data-abstraction process, which provides automatically derived qualitative values and patterns. The temporal abstraction is oriented on a context-sensitive and expectation-guided principle. Additional knowledge derived from domain experts forms an essential part for all of these methods. The methods are applied in the field of artificial ventilation of newborn infants. Examples from the real-time monitoring and therapy-planning system VIE-VENT illustrate the usefulness and effectiveness of the methods.

An Efficient Method for the Isolation of Highly Purified RNA from Seeds for Use in Quantitative Transcriptome Analysis.

PubMed

Kanai, Masatake; Mano, Shoji; Nishimura, Mikio

2017-01-11

Plant seeds accumulate large amounts of storage reserves comprising biodegradable organic matter. Humans rely on seed storage reserves for food and as industrial materials. Gene expression profiles are powerful tools for investigating metabolic regulation in plant cells. Therefore, detailed, accurate gene expression profiles during seed development are required for crop breeding. Acquiring highly purified RNA is essential for producing these profiles. Efficient methods are needed to isolate highly purified RNA from seeds. Here, we describe a method for isolating RNA from seeds containing large amounts of oils, proteins, and polyphenols, which have inhibitory effects on high-purity RNA isolation. Our method enables highly purified RNA to be obtained from seeds without the use of phenol, chloroform, or additional processes for RNA purification. This method is applicable to Arabidopsis, rapeseed, and soybean seeds. Our method will be useful for monitoring the expression patterns of low level transcripts in developing and mature seeds.

Relationship between Geography-Tourism and Tourism's Effects According to High School Students

ERIC Educational Resources Information Center

Koca, Nusret; Yildirim, Ramazan

2018-01-01

This research was designed in the screening model to determine the opinions of high school students on tourism effects and geography-tourism relations. The data were gathered from 760 students who were educated in high schools in the central district of Kütahya, identified by cluster sampling method. The data were collected with the help of a…

Determination of skeleton and sign map for phase obtaining from a single ESPI image

NASA Astrophysics Data System (ADS)

Yang, Xia; Yu, Qifeng; Fu, Sihua

2009-06-01

A robust method of determining the sign map and skeletons for ESPI images is introduced in this paper. ESPI images have high speckle noise which makes it difficult to obtain the fringe information, especially from a single image. To overcome the effects of high speckle noise, local directional computing windows are designed according to the fringe directions. Then by calculating the gradients from the filtered image in directional windows, sign map and good skeletons can be determined robustly. Based on the sign map, single image phase-extracting methods such as quadrature transform can be improved. And based on skeletons, fringe phases can be obtained directly by normalization methods. Experiments show that this new method is robust and effective for extracting phase from a single ESPI fringe image.

Life prediction for high temperature low cycle fatigue of two kinds of titanium alloys based on exponential function

NASA Astrophysics Data System (ADS)

Mu, G. Y.; Mi, X. Z.; Wang, F.

2018-01-01

The high temperature low cycle fatigue tests of TC4 titanium alloy and TC11 titanium alloy are carried out under strain controlled. The relationships between cyclic stress-life and strain-life are analyzed. The high temperature low cycle fatigue life prediction model of two kinds of titanium alloys is established by using Manson-Coffin method. The relationship between failure inverse number and plastic strain range presents nonlinear in the double logarithmic coordinates. Manson-Coffin method assumes that they have linear relation. Therefore, there is bound to be a certain prediction error by using the Manson-Coffin method. In order to solve this problem, a new method based on exponential function is proposed. The results show that the fatigue life of the two kinds of titanium alloys can be predicted accurately and effectively by using these two methods. Prediction accuracy is within ±1.83 times scatter zone. The life prediction capability of new methods based on exponential function proves more effective and accurate than Manson-Coffin method for two kinds of titanium alloys. The new method based on exponential function can give better fatigue life prediction results with the smaller standard deviation and scatter zone than Manson-Coffin method. The life prediction results of two methods for TC4 titanium alloy prove better than TC11 titanium alloy.

Treatment of addiction and addiction-related behavior

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dewey, S.L.; Brodie, J.D.; Ashby, C.R. Jr.

2000-05-02

The present invention provides a highly efficient method for treating substance addiction and for changing addiction-related behavior of a primate suffering from substance addiction. The method includes administering to a primate an effective amount of a pharmaceutical composition including gamma vinylGABA. The present invention also provides a method of treatment of nicotine addiction by treating a patient with an effective amount of a composition including gamma vinylGABA.

Treatment of addiction and addiction-related behavior

DOEpatents

Dewey, Stephen L.; Brodie, Jonathan D.; Ashby, Jr., Charles R.

2000-01-01

The present invention provides a highly efficient method for treating substance addiction and for changing addiction-related behavior of a primate suffering from substance addiction. The method includes administering to a primate an effective amount of a pharmaceutical composition including gamma vinylGABA. The present invention also provides a method of treatment of nicotine addiction by treating a patient with an effective amount of a composition including gamma vinylGABA.

Derek Vigil-Fowler | NREL

Science.gov Websites

simulation methods for materials physics and chemistry, with particular expertise in post-DFT, high accuracy methods such as the GW approximation for electronic structure and random phase approximation (RPA) total the art in computational methods, including efficient methods for including the effects of substrates

High throughput selection of antibiotic-resistant transgenic Arabidopsis plants.

PubMed

Nagashima, Yukihiro; Koiwa, Hisashi

2017-05-15

Kanamycin resistance is the most frequently used antibiotic-resistance marker for Arabidopsis transformations, however, this method frequently causes escape of untransformed plants, particularly at the high seedling density during the selection. Here we developed a robust high-density selection method using top agar for Arabidopsis thaliana. Top agar effectively suppressed growth of untransformed wild-type plants on selection media at high density. Survival of the transformed plants during the selection were confirmed by production of green true leaves and expression of a firefly luciferase reporter gene. Top agar method allowed selection using a large amount of seeds in Arabidopsis transformation. Copyright © 2017 Elsevier Inc. All rights reserved.

A high-throughput multiplex method adapted for GMO detection.

PubMed

Chaouachi, Maher; Chupeau, Gaëlle; Berard, Aurélie; McKhann, Heather; Romaniuk, Marcel; Giancola, Sandra; Laval, Valérie; Bertheau, Yves; Brunel, Dominique

2008-12-24

A high-throughput multiplex assay for the detection of genetically modified organisms (GMO) was developed on the basis of the existing SNPlex method designed for SNP genotyping. This SNPlex assay allows the simultaneous detection of up to 48 short DNA sequences (approximately 70 bp; "signature sequences") from taxa endogenous reference genes, from GMO constructions, screening targets, construct-specific, and event-specific targets, and finally from donor organisms. This assay avoids certain shortcomings of multiplex PCR-based methods already in widespread use for GMO detection. The assay demonstrated high specificity and sensitivity. The results suggest that this assay is reliable, flexible, and cost- and time-effective for high-throughput GMO detection.

Unified pipe network method for simulation of water flow in fractured porous rock

NASA Astrophysics Data System (ADS)

Ren, Feng; Ma, Guowei; Wang, Yang; Li, Tuo; Zhu, Hehua

2017-04-01

Rock masses are often conceptualized as dual-permeability media containing fractures or fracture networks with high permeability and porous matrix that is less permeable. In order to overcome the difficulties in simulating fluid flow in a highly discontinuous dual-permeability medium, an effective unified pipe network method is developed, which discretizes the dual-permeability rock mass into a virtual pipe network system. It includes fracture pipe networks and matrix pipe networks. They are constructed separately based on equivalent flow models in a representative area or volume by taking the advantage of the orthogonality of the mesh partition. Numerical examples of fluid flow in 2-D and 3-D domain including porous media and fractured porous media are presented to demonstrate the accuracy, robustness, and effectiveness of the proposed unified pipe network method. Results show that the developed method has good performance even with highly distorted mesh. Water recharge into the fractured rock mass with complex fracture network is studied. It has been found in this case that the effect of aperture change on the water recharge rate is more significant in the early stage compared to the fracture density change.

Star tracking method based on multiexposure imaging for intensified star trackers.

PubMed

Yu, Wenbo; Jiang, Jie; Zhang, Guangjun

2017-07-20

The requirements for the dynamic performance of star trackers are rapidly increasing with the development of space exploration technologies. However, insufficient knowledge of the angular acceleration has largely decreased the performance of the existing star tracking methods, and star trackers may even fail to track under highly dynamic conditions. This study proposes a star tracking method based on multiexposure imaging for intensified star trackers. The accurate estimation model of the complete motion parameters, including the angular velocity and angular acceleration, is established according to the working characteristic of multiexposure imaging. The estimation of the complete motion parameters is utilized to generate the predictive star image accurately. Therefore, the correct matching and tracking between stars in the real and predictive star images can be reliably accomplished under highly dynamic conditions. Simulations with specific dynamic conditions are conducted to verify the feasibility and effectiveness of the proposed method. Experiments with real starry night sky observation are also conducted for further verification. Simulations and experiments demonstrate that the proposed method is effective and shows excellent performance under highly dynamic conditions.

High-throughput determination of vancomycin in human plasma by a cost-effective system of two-dimensional liquid chromatography.

PubMed

Sheng, Yanghao; Zhou, Boting

2017-05-26

Therapeutic drug monitoring (TDM) is one of the most important services of clinical laboratories. Two main techniques are commonly used: the immunoassay and chromatography method. We have developed a cost-effective system of two-dimensional liquid chromatography with ultraviolet detection (2D-LC-UV) for high-throughput determination of vancomycin in human plasma that combines the automation and low start-up costs of the immunoassay with the high selectivity and sensitivity of the liquid chromatography coupled with mass spectrometric detection without incurring their disadvantages, achieving high cost-effectiveness. This 2D-LC system offers a large volume injection to provide sufficient sensitivity and uses simulated gradient peak compression technology to control peak broadening and to improve peak shape. A middle column was added to reduce the analysis cycle time and make it suitable for high-throughput routine clinical assays. The analysis cycle time was 4min and the peak width was 0.8min. Compared with other chromatographic methods that have been developed, the analysis cycle time and peak width for vancomycin was reduced significantly. The lower limit of quantification was 0.20μg/mL for vancomycin, which is the same as certain LC-MS/MS methods that have been recently developed and validated. The method is rapid, automated, and low-cost and has high selectivity and sensitivity for the quantification of vancomycin in human plasma, thus making it well-suited for use in hospital clinical laboratories. Copyright © 2017 Elsevier B.V. All rights reserved.

An implicit spatial and high-order temporal finite difference scheme for 2D acoustic modelling

NASA Astrophysics Data System (ADS)

Wang, Enjiang; Liu, Yang

2018-01-01

The finite difference (FD) method exhibits great superiority over other numerical methods due to its easy implementation and small computational requirement. We propose an effective FD method, characterised by implicit spatial and high-order temporal schemes, to reduce both the temporal and spatial dispersions simultaneously. For the temporal derivative, apart from the conventional second-order FD approximation, a special rhombus FD scheme is included to reach high-order accuracy in time. Compared with the Lax-Wendroff FD scheme, this scheme can achieve nearly the same temporal accuracy but requires less floating-point operation times and thus less computational cost when the same operator length is adopted. For the spatial derivatives, we adopt the implicit FD scheme to improve the spatial accuracy. Apart from the existing Taylor series expansion-based FD coefficients, we derive the least square optimisation based implicit spatial FD coefficients. Dispersion analysis and modelling examples demonstrate that, our proposed method can effectively decrease both the temporal and spatial dispersions, thus can provide more accurate wavefields.

The Effect of Computer Games on Students' Critical Thinking Disposition and Educational Achievement

ERIC Educational Resources Information Center

Seifi, Mohammad; Derikvandi, Zahra; Moosavipour, Saeed; Khodabandelou, Rouhollah

2015-01-01

The main aim of this research was to investigate the effect of computer games on student' critical thinking disposition and educational achievement. The research method was descriptive, and its type was casual-comparative. The sample included 270 female high school students in Andimeshk town selected by multistage cluster method. Ricketts…

Markov Chain Monte Carlo Joint Analysis of Chandra X-Ray Imaging Spectroscopy and Sunyaev-Zel'dovich Effect Data

NASA Technical Reports Server (NTRS)

Bonamente, Massimillano; Joy, Marshall K.; Carlstrom, John E.; Reese, Erik D.; LaRoque, Samuel J.

2004-01-01

X-ray and Sunyaev-Zel'dovich effect data can be combined to determine the distance to galaxy clusters. High-resolution X-ray data are now available from Chandra, which provides both spatial and spectral information, and Sunyaev-Zel'dovich effect data were obtained from the BIMA and Owens Valley Radio Observatory (OVRO) arrays. We introduce a Markov Chain Monte Carlo procedure for the joint analysis of X-ray and Sunyaev- Zel'dovich effect data. The advantages of this method are the high computational efficiency and the ability to measure simultaneously the probability distribution of all parameters of interest, such as the spatial and spectral properties of the cluster gas and also for derivative quantities such as the distance to the cluster. We demonstrate this technique by applying it to the Chandra X-ray data and the OVRO radio data for the galaxy cluster A611. Comparisons with traditional likelihood ratio methods reveal the robustness of the method. This method will be used in follow-up paper to determine the distances to a large sample of galaxy cluster.

Analysis of thermal stresses in HfO2/SiO2 high reflective optical coatings for high power laser applications

NASA Astrophysics Data System (ADS)

Gao, Chunxue; Zhao, Zhiwei; Zhu, Zhuoya; Li, Shuang; Mi, Changwen

2015-02-01

HfO2/SiO2 high reflective optical coatings are widely used in high power laser applications because of their high laser damage resistance and appropriate spectral performance. The residual stresses strongly influence the performance and longevity of the optical coatings. Thermal stresses are the primary components of the residual stresses. In the present work, the distribution of thermal stresses in HfO2/SiO2 high reflective optical coatings was investigated using two different computational methods: finite element method (FEM) and an analytical method based on force and moment balances and classical beam bending theory. The results by these two methods were compared and found to be in agreement with each other, demonstrating that these two methods are effective and accurate ways to predict the thermal stresses in HfO2/SiO2 optical coatings. In addition, these two methods were also used to obtain the thermal stresses in HfO2/SiO2 optical coatings with different layer number to investigate the effect of the layer number on the thermal stresses of the HfO2/SiO2 optical coatings. The results show that with the increase of the layer number, the stresses in the substrate increase, while the stresses in the respective SiO2 and HfO2 layers decrease. Besides, it was also found that the radius of curvature of the coating system decreases as the layer number increases, leading to larger bending curvature in the system.

Comparison of lifetime-based methods for 2D phosphor thermometry in high-temperature environment

NASA Astrophysics Data System (ADS)

Peng, Di; Liu, Yingzheng; Zhao, Xiaofeng; Kim, Kyung Chun

2016-09-01

This paper discusses the currently available techniques for 2D phosphor thermometry, and compares the performance of two lifetime-based methods: high-speed imaging and the dual-gate. High-speed imaging resolves luminescent decay with a fast frame rate, and has become a popular method for phosphor thermometry in recent years. But it has disadvantages such as high equipment cost and long data processing time, and it would fail at sufficiently high temperature due to a low signal-to-noise ratio and short lifetime. The dual-gate method only requires two images on the decay curve and therefore greatly reduces cost in hardware and processing time. A dual-gate method for phosphor thermometry has been developed and compared with the high-speed imaging method through both calibration and a jet impingement experiment. Measurement uncertainty has been evaluated for a temperature range of 473-833 K. The effects of several key factors on uncertainty have been discussed, including the luminescent signal level, the decay lifetime and temperature sensitivity. The results show that both methods are valid for 2D temperature sensing within the given range. The high-speed imaging method shows less uncertainty at low temperatures where the signal level and the lifetime are both sufficient, but its performance is degraded at higher temperatures due to a rapidly reduced signal and lifetime. For T  >  750 K, the dual-gate method outperforms the high-speed imaging method thanks to its superiority in signal-to-noise ratio and temperature sensitivity. The dual-gate method has great potential for applications in high-temperature environments where the high-speed imaging method is not applicable.

Stress Management Strategies for Students: The Immediate Effects of Yoga, Humor, and Reading on Stress

ERIC Educational Resources Information Center

Rizzolo, Denise; Zipp, Genevieve Pinto; Stiskal, Doreen; Simpkins, Susan

2009-01-01

Background: Health science programs can be demanding and difficult for many students, leading to high levels of stress. High levels of stress can have a negative effect on students and subsequently the practicing clinician. Research suggests that yoga, humor, and reading are simple, effective methods to help reduce stress. To date no research…

The Michigan Public High School Context and Performance Report Card

ERIC Educational Resources Information Center

Van Beek, Michael; Bowen, Daniel; Mills, Jonathan

2012-01-01

Assessing a high school's effectiveness is not straightforward. Comparing a school's standardized test scores to those of other schools is one approach to measuring effectiveness, but a major objection to this method is that students' test scores tend to be related to students' "socioeconomic" status--family household income, for…

Laser heat puncturing as highly effective method of post-tuberculous cystalgia treatment

NASA Astrophysics Data System (ADS)

Koultchavenia, Ekaterina V.; Krasnov, Vladimir A.

1999-09-01

The tuberculosis of an urine bladder in men develops less often, and recovery is authentic more often, than in women. In 39.1% of the female patients with nephrotuberculosis, a specific cystitis is finished in postturberculous cystalgia. One of starting mechanisms of disuria after urocystis tuberculosis in the women in menopause is hormonal insufficiency. The method of laserheatpuncturing, developed by us, for the treatment this complication is highly effective, does not require additional introduction of medicines, can be executed as in hospitals, and in out-patient.

Alternate methods for high level pyrotechnic shock simulation

NASA Astrophysics Data System (ADS)

Gray, Phillip J., Sr.

Two effective methods to recreate a realistic pyrotechnic shock are presented. The first method employs a resonant beam and is used for SRS levels of 12,000 G or more. The test unit is at one end of the beam and a hammer strikes the opposite end causing a shock to be transmitted to the other end of the fixture. The second method is based on a standard shaker system with a resonant beam to amplify the input signal. The engineer defines the duration of the shock signal induced to the vibration amplifier using the GenRad 2514 controller. The shock signal is then input via the shaker to the resonant beam, which amplifies the signal to produce the desired response at the end of the fixture. The shock response spectrum stays within a +/-6 dB tolerance with levels as high as 3000 G peak. These methods are repeatable, reliable, cost-effective, and consistent with a real pyroevent.

Algorithms for image recovery calculation in extended single-shot phase-shifting digital holography

NASA Astrophysics Data System (ADS)

Hasegawa, Shin-ya; Hirata, Ryo

2018-04-01

The single-shot phase-shifting method of image recovery using an inclined reference wave has the advantages of reducing the effects of vibration, being capable of operating in real time, and affording low-cost sensing. In this method, relatively low reference angles compared with that in the conventional method using phase shift between three or four pixels has been required. We propose an extended single-shot phase-shifting technique which uses the multiple-step phase-shifting algorithm and the corresponding multiple pixels which are the same as that of the period of an interference fringe. We have verified the theory underlying this recovery method by means of Fourier spectral analysis and its effectiveness by evaluating the visibility of the image using a high-resolution pattern. Finally, we have demonstrated high-contrast image recovery experimentally using a resolution chart. This method can be used in a variety of applications such as color holographic interferometry.

Adjoint Fokker-Planck equation and runaway electron dynamics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Chang; Brennan, Dylan P.; Bhattacharjee, Amitava

2016-01-15

The adjoint Fokker-Planck equation method is applied to study the runaway probability function and the expected slowing-down time for highly relativistic runaway electrons, including the loss of energy due to synchrotron radiation. In direct correspondence to Monte Carlo simulation methods, the runaway probability function has a smooth transition across the runaway separatrix, which can be attributed to effect of the pitch angle scattering term in the kinetic equation. However, for the same numerical accuracy, the adjoint method is more efficient than the Monte Carlo method. The expected slowing-down time gives a novel method to estimate the runaway current decay timemore » in experiments. A new result from this work is that the decay rate of high energy electrons is very slow when E is close to the critical electric field. This effect contributes further to a hysteresis previously found in the runaway electron population.« less

Effects of improved process for CuO-doped NKN lead-free ceramics on high-power piezoelectric transformers.

PubMed

Yang, Song-Ling; Tsai, Cheng-Che; Liou, Yi-Cheng; Hong, Cheng-Shong; Li, Bing-Jing; Chu, Sheng-Yuan

2011-12-01

In this paper, the effects of the electrical proper- ties of CuO-doped (Na(0.5)K(0.5))NbO(3) (NKN) ceramics prepared separately using the B-site oxide precursor method (BO method) and conventional mixed-oxide method (MO method) on high-power piezoelectric transformers (PTs) were investigated. The performances of PTs made with these two substrates were compared. Experimental results showed that the output power and temperature stability of PTs could be enhanced because of the lower resonant impedance of the ceramics prepared using the BO method. In addition, the output power of PTs was more affected by the resonant impedance than by the mechanical quality factor (Q(m)) of the ceramics. The PTs fabricated with ceramics prepared using the BO method showed a high efficiency of more than 94% and a maximum output power of 8.98 W (power density: 18.3 W/cm(3)) with temperature increase of 3°C under the optimum load resistance (5 kΩ) and an input voltage of 150 V(pp). This output power of the lead-free disk-type PTs is the best reported so far.

Young women's attitudes towards, and experiences of, long-acting reversible contraceptives.

PubMed

Bracken, Jennifer; Graham, Cynthia A

2014-08-01

To identify factors involved in women's decisions to choose particular contraceptive methods and more specifically, incentives and disincentives to use three long-acting reversible contraceptive (LARC) methods: injectables, implants, and intrauterine devices/systems (IUDs/IUSs). A total of 502 women aged 18 to 30 completed a cross-sectional online questionnaire. The three most important factors in choosing a contraceptive method were: high efficacy at preventing pregnancy, protection against sexually transmitted infections, and non-interference with sexual intercourse. The most common incentives for LARC use were the high efficacy and long duration of action. Disincentives included the possibility of irregular bleeding and concerns about effects on fertility; fear of needles and pain was a particular disincentive for IUD/IUS use. Only 93 (18%) of the participants reported ever having used a LARC. Reported disincentives to LARC use (e.g., concern about effects on future fertility) indicated that many young women hold inaccurate beliefs about these methods. The relatively high proportions of women who held neutral attitudes about LARCs (21-40%, depending on the method) highlight the importance of education and contraceptive counselling to improve knowledge about the advantages of these methods.

Sharpening method of satellite thermal image based on the geographical statistical model

NASA Astrophysics Data System (ADS)

Qi, Pengcheng; Hu, Shixiong; Zhang, Haijun; Guo, Guangmeng

2016-04-01

To improve the effectiveness of thermal sharpening in mountainous regions, paying more attention to the laws of land surface energy balance, a thermal sharpening method based on the geographical statistical model (GSM) is proposed. Explanatory variables were selected from the processes of land surface energy budget and thermal infrared electromagnetic radiation transmission, then high spatial resolution (57 m) raster layers were generated for these variables through spatially simulating or using other raster data as proxies. Based on this, the local adaptation statistical relationship between brightness temperature (BT) and the explanatory variables, i.e., the GSM, was built at 1026-m resolution using the method of multivariate adaptive regression splines. Finally, the GSM was applied to the high-resolution (57-m) explanatory variables; thus, the high-resolution (57-m) BT image was obtained. This method produced a sharpening result with low error and good visual effect. The method can avoid the blind choice of explanatory variables and remove the dependence on synchronous imagery at visible and near-infrared bands. The influences of the explanatory variable combination, sampling method, and the residual error correction on sharpening results were analyzed deliberately, and their influence mechanisms are reported herein.

Novel high speed fiber-optic pressure sensor systems.

DOT National Transportation Integrated Search

2014-03-01

The goal of this project is to develop a complete test of this technology for high-speed, high-accuracy applications, specifically cost-effective data acquisition techniques and practical mounting methods tailored for the subject environment. The sec...

Kic size effect study on two high-strength steels using notched bend specimens

NASA Technical Reports Server (NTRS)

Stonesifer, F. R.

1974-01-01

Five methods are used to calculate plane strain fracture toughness (K sub Q) values for bend-specimens of various sizes from two high-strength steels. None of the methods appeared to satisfactorily predict valid stress intensity factor (K sub IC) values from specimens of sizes well below that required by E399 standard tests.

Online Reading Comprehension among Seventh Grade Students with High Incidence Disabilities in Inclusive Settings: A Mixed Methods Study

ERIC Educational Resources Information Center

Robbins, Katherine R.

2010-01-01

Because research exploring how students with disabilities read and comprehend on the Internet is scarce, a mixed methods study was implemented to determine if Internet Reciprocal Teaching (IRT) is an effective intervention for improving online reading comprehension among seventh grade students with high-incidence disabilities in inclusive…

Randomized Controlled Trial of Teaching Methods: Do Classroom Experiments Improve Economic Education in High Schools?

ERIC Educational Resources Information Center

Eisenkopf, Gerald; Sulser, Pascal A.

2016-01-01

The authors present results from a comprehensive field experiment at Swiss high schools in which they compare the effectiveness of teaching methods in economics. They randomly assigned classes into an experimental and a conventional teaching group, or a control group that received no specific instruction. Both teaching treatments improve economic…

An Evaluation of Three Methods of Saying "No" to Avoid an Escalating Response Class Hierarchy

ERIC Educational Resources Information Center

Mace, F. Charles; Pratt, Jamie L.; Prager, Kevin L.; Pritchard, Duncan

2011-01-01

We evaluated the effects of three different methods of denying access to requested high-preference activities on escalating problem behavior. Functional analysis and response class hierarchy (RCH) assessment results indicated that 4 topographies of problem behaviors displayed by a 13-year-old boy with high-functioning autism constituted an RCH…

Identifying High Academic Potential in Australian Aboriginal Children Using Dynamic Testing

ERIC Educational Resources Information Center

Chaffey, Graham W.; Bailey, Stan B.; Vine, Ken W.

2015-01-01

The primary purpose of this study was to determine the effectiveness of dynamic testing as a method for identifying high academic potential in Australian Aboriginal children. The 79 participating Aboriginal children were drawn from Years 3-5 in rural schools in northern New South Wales. The dynamic testing method used in this study involved a…

Preparation of Sesquiterpenoids from Tussilago farfara L. by High-speed Counter-current Chromatography

PubMed Central

Cao, Kun; Xu, Yi; Zhao, Tian-Ming; Zhang, Qing

2016-01-01

Background: Sesquiterpenoids, such as tussilagone, has effects of raising blood pressure, antiplatelet aggregation, and anti-inflammation activities, which is regarded as index compound for quality control of Tussilago farfara L. Objective: This study was aimed to obtain an effective method for fast isolation of sesquiterpenoids from T. farfara L. by high-speed counter-current chromatography (HSCCC). Materials and Methods: A solvent optimization method for HSCCC was presented, i.e., the separation factors of compounds after the K values of solvent system should be investigated. Results: A ternary solvent system of n-hexane:methanol:water (5:8:2, v/v/v) was selected and applied for the HSCCC, and 56 mg of tussilagone (2) was isolated from T. farfara L., along with two other sesquiterpenoids 5.6 mg of 2,2-dimethyl-6-acetylchromanone (1) and 22 mg of 14-acetoxy-7 β-(3’-ethyl cis-crotonoyloxy)-lα-(2’-methylbutyryloxy)-notonipetranone (3) by HSCCC with high purities. Their chemical structures were elucidated by liquid chromatography-mass spectrometry and nuclear magnetic resonance experiments. Conclusion: These results offered an efficient strategy for preparation of potentially health-relevant phytochemicals from T. farfara L., which might be used for further chemical research and pharmacological studies by preparative HSCCC. SUMMARY The real separation efficiency has been verified by analytical HSCCC.A solvent optimization method for HSCCC was presented and applied to separate and prepare active compounds.A method for rapid and effective separation of target compound Tussilagone with high yield and purity from the flower buds of Tussilago farfara.Two other compounds 2,2-Dimethyl-6-acetylchromanone and 14-acetoxy-7β-(3’-ethyl cis-crotonoyloxy) -lα- (2’-methylbutyryloxy). notonipetranone hasbeen obtained with high purities from flower buds of Tussilago farfara. Abbreviations used: HSCCC: High-Speed Counter-Current Chromatography; LC-MS: Liquid Chromatograph-Mass Spectrometer; NMR: Nuclear Magnetic Resonance; TCM: Traditional Chinese Medicine; HPLC: High Performance Liquid Chromatography; ESI-MS: Electrospray Ionization Mass Spectrometry; PE: petroleum ether PMID:27867270

Characterisation of a new, highly effective method for detecting nematode eggs (Ascaris spp., Toxocara spp., Trichuris spp.) in sewage sludge containing flocculants.

PubMed

Zdybel, Jolanta; Karamon, Jacek; Różycki, Mirosław; Bilska-Zając, Ewa; Kłapeć, Teresa; Cencek, Tomasz

2016-11-01

Because traditional methods used for sewage sludge parasitological examinations have low sensitivity, a new, highly effective method (own method - OM) was devised. The principle of this method is to eliminate the flocculent effect on the structure of sewage sludge by mechanically damaging floccules in the presence of surfactants and to increase the effectiveness of egg isolation processes in large volumes of liquids. The objective of this study was to estimate the effectiveness of the OM in detecting nematode eggs in sewage sludge samples containing flocculants. In the first stage, the effectiveness of the OM was compared to 4 other methods routinely used in parasitological examinations of dehydrated sewage sludge. Next, method standardisation was performed using sewage sludge samples supplemented with eggs from 3 parasite species (Ascaris suum, Toxocara canis and Trichuris vulpis). The study demonstrated that OM efficiency was 6-65 times greater than other methods, depending on the method and type of detected eggs. Limit of detection (LOD) calculations for the OM were performed on samples supplemented with a known number of parasite eggs resulting in 10, 5 and 3 eggs/50 g of sample for A. suum, T. vulpis and T. canis eggs, respectively. The limits of quantification (LOQ) of the OM were established as 200 eggs/50 g of sample for A. suum and T. vulpis eggs and 50 eggs/50 g of sample for T. canis eggs. The rectilinear regression functions, which determined the relationship between the number of eggs detected in OM measurements and the number of eggs contained in the samples, were characterised by high and statistically significant coefficients of determination (r 2 ). The slopes of the trend lines were 0.3188, 0.3821 and 0.3276, and the intercepts were -11.223, -9.0261 and -23.15 for A. suum, T. canis and T. vulpis eggs, respectively. Method sensitivity, calculated as the slope coefficient of the regression function and expressed as a percentage, ranged from 32% to 38% depending on egg type. The study confirmed that the OM may be applied to quantify parasite eggs in dehydrated sewage sludge containing polyelectrolytes. Copyright © 2016 Elsevier Inc. All rights reserved.

AN APPROACH TO METHODS DEVELOPMENT FOR HUMAN EXPOSURE ASSESSMENT STUDIES

EPA Science Inventory

Human exposure assessment studies require methods that are rapid, cost-effective and have a high sample through-put. The development of analytical methods for exposure studies should be based on specific information for individual studies. Human exposure studies suggest that di...

Quench Detection and Protection for High Temperature Superconducting Transformers by Using the Active Power Method

NASA Astrophysics Data System (ADS)

Nanato, N.; Kobayashi, Y.

AC high temperature superconducting (HTS) coils have been developed for transformers, motors and so on. Quench detection and protection system are essential for safety operations of the AC HTS facilities. The balance voltage method is universally used for the quench detection and protection, however especially for AC operations, the method has risks in terms of high voltage sparks. Because the method needs a voltage tap soldered to a midpoint of the coil winding and the AC HTS facilities generally operate at high voltages and therefore high voltage sparks may occur at the midpoint with no insulation. We have proposed the active power method for the quench detection and protection. The method requires no voltage tap on the midpoint of the coil winding and therefore it has in-built effectiveness for the AC HTS facilities. In this paper, we show that the method can detect the quench in an HTS transformer and moreover our proposed quench protection circuits which consist of thyristors are simple and useful for the AC HTS facilities.

EPS-LASSO: Test for High-Dimensional Regression Under Extreme Phenotype Sampling of Continuous Traits.

PubMed

Xu, Chao; Fang, Jian; Shen, Hui; Wang, Yu-Ping; Deng, Hong-Wen

2018-01-25

Extreme phenotype sampling (EPS) is a broadly-used design to identify candidate genetic factors contributing to the variation of quantitative traits. By enriching the signals in extreme phenotypic samples, EPS can boost the association power compared to random sampling. Most existing statistical methods for EPS examine the genetic factors individually, despite many quantitative traits have multiple genetic factors underlying their variation. It is desirable to model the joint effects of genetic factors, which may increase the power and identify novel quantitative trait loci under EPS. The joint analysis of genetic data in high-dimensional situations requires specialized techniques, e.g., the least absolute shrinkage and selection operator (LASSO). Although there are extensive research and application related to LASSO, the statistical inference and testing for the sparse model under EPS remain unknown. We propose a novel sparse model (EPS-LASSO) with hypothesis test for high-dimensional regression under EPS based on a decorrelated score function. The comprehensive simulation shows EPS-LASSO outperforms existing methods with stable type I error and FDR control. EPS-LASSO can provide a consistent power for both low- and high-dimensional situations compared with the other methods dealing with high-dimensional situations. The power of EPS-LASSO is close to other low-dimensional methods when the causal effect sizes are small and is superior when the effects are large. Applying EPS-LASSO to a transcriptome-wide gene expression study for obesity reveals 10 significant body mass index associated genes. Our results indicate that EPS-LASSO is an effective method for EPS data analysis, which can account for correlated predictors. The source code is available at https://github.com/xu1912/EPSLASSO. hdeng2@tulane.edu. Supplementary data are available at Bioinformatics online. © The Author (2018). Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com

Relevant Feature Set Estimation with a Knock-out Strategy and Random Forests

PubMed Central

Ganz, Melanie; Greve, Douglas N.; Fischl, Bruce; Konukoglu, Ender

2015-01-01

Group analysis of neuroimaging data is a vital tool for identifying anatomical and functional variations related to diseases as well as normal biological processes. The analyses are often performed on a large number of highly correlated measurements using a relatively smaller number of samples. Despite the correlation structure, the most widely used approach is to analyze the data using univariate methods followed by post-hoc corrections that try to account for the data’s multivariate nature. Although widely used, this approach may fail to recover from the adverse effects of the initial analysis when local effects are not strong. Multivariate pattern analysis (MVPA) is a powerful alternative to the univariate approach for identifying relevant variations. Jointly analyzing all the measures, MVPA techniques can detect global effects even when individual local effects are too weak to detect with univariate analysis. Current approaches are successful in identifying variations that yield highly predictive and compact models. However, they suffer from lessened sensitivity and instabilities in identification of relevant variations. Furthermore, current methods’ user-defined parameters are often unintuitive and difficult to determine. In this article, we propose a novel MVPA method for group analysis of high-dimensional data that overcomes the drawbacks of the current techniques. Our approach explicitly aims to identify all relevant variations using a “knock-out” strategy and the Random Forest algorithm. In evaluations with synthetic datasets the proposed method achieved substantially higher sensitivity and accuracy than the state-of-the-art MVPA methods, and outperformed the univariate approach when the effect size is low. In experiments with real datasets the proposed method identified regions beyond the univariate approach, while other MVPA methods failed to replicate the univariate results. More importantly, in a reproducibility study with the well-known ADNI dataset the proposed method yielded higher stability and power than the univariate approach. PMID:26272728

Fluorine-free preparation of titanium carbide MXene quantum dots with high near-infrared photothermal performances for cancer therapy.

PubMed

Yu, Xinghua; Cai, Xingke; Cui, Haodong; Lee, Seung-Wuk; Yu, Xue-Feng; Liu, Bilu

2017-11-23

Titanium carbide MXene quantum dots (QDs) were synthesized using an effective fluorine-free method as a biocompatible and highly efficient nanoagent for photothermal therapy (PTT) applications. In contrast to the traditional, hazardous and time-consuming process of HF pretreatment, our fluorine-free method is safe and simple. More importantly, abundant Al oxoanions were found to be modified on the MXene QD surface by the fluorine-free method, which endowed the QDs with strong and broad absorption in the NIR region. As a result, the as-prepared MXene QDs exhibited an extinction coefficient as large as 52.8 Lg -1 cm -1 at 808 nm and a photothermal conversion efficiency as high as 52.2%. Both the values are among the best reported so far. The as-prepared MXene QDs achieved simultaneous photoacoustic (PA) imaging and the remarkable PTT effect of tumors. Moreover, MXene QDs showed great biocompatibility without causing noticeable toxicity in vitro and in vivo, indicating their high potential for clinical applications.

System and method for generating a displacement with ultra-high accuracy using a fabry-perot interferometer

DOEpatents

McIntyre, Timothy J.

1994-01-01

A system and method for generating a desired displacement of an object, i.e., a target, from a reference position with ultra-high accuracy utilizes a Fabry-Perot etalon having an expandable tube cavity for resolving, with an Iodine stabilized laser, displacements with high accuracy and for effecting (as an actuator) displacements of the target. A mechanical amplifier in the form of a micropositioning stage has a platform and a frame which are movable relative to one another, and the tube cavity of the etalon is connected between the platform and frame so that an adjustment in length of the cavity effects a corresponding, amplified movement of the frame relative to the cavity. Therefore, in order to provide a preselected magnitude of displacement of the stage frame relative to the platform, the etalon tube cavity is adjusted in length by a corresponding amount. The system and method are particularly well-suited for use when calibrating a high accuracy measuring device.

High performance computation of residual stress and distortion in laser welded 301L stainless sheets

DOE PAGES

Huang, Hui; Tsutsumi, Seiichiro; Wang, Jiandong; ...

2017-07-11

Transient thermo-mechanical simulation of stainless plate laser welding process was performed by a highly efficient and accurate approach-hybrid iterative substructure and adaptive mesh method. Especially, residual stress prediction was enhanced by considering various heat effects in the numerical model. The influence of laser welding heat input on residual stress and welding distortion of stainless thin sheets were investigated by experiment and simulation. X-ray diffraction (XRD) and contour method were used to measure the surficial and internal residual stress respectively. Effect of strain hardening, annealing and melting on residual stress prediction was clarified through a parametric study. It was shown thatmore » these heat effects must be taken into account for accurate prediction of residual stresses in laser welded stainless sheets. Reasonable agreement among residual stresses by numerical method, XRD and contour method was obtained. Buckling type welding distortion was also well reproduced by the developed thermo-mechanical FEM.« less

High performance computation of residual stress and distortion in laser welded 301L stainless sheets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Hui; Tsutsumi, Seiichiro; Wang, Jiandong

Transient thermo-mechanical simulation of stainless plate laser welding process was performed by a highly efficient and accurate approach-hybrid iterative substructure and adaptive mesh method. Especially, residual stress prediction was enhanced by considering various heat effects in the numerical model. The influence of laser welding heat input on residual stress and welding distortion of stainless thin sheets were investigated by experiment and simulation. X-ray diffraction (XRD) and contour method were used to measure the surficial and internal residual stress respectively. Effect of strain hardening, annealing and melting on residual stress prediction was clarified through a parametric study. It was shown thatmore » these heat effects must be taken into account for accurate prediction of residual stresses in laser welded stainless sheets. Reasonable agreement among residual stresses by numerical method, XRD and contour method was obtained. Buckling type welding distortion was also well reproduced by the developed thermo-mechanical FEM.« less

Rietveld analysis using powder diffraction data with anomalous scattering effect obtained by focused beam flat sample method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tanaka, Masahiko, E-mail: masahiko@spring8.or.jp; Katsuya, Yoshio, E-mail: katsuya@spring8.or.jp; Sakata, Osami, E-mail: SAKATA.Osami@nims.go.jp

2016-07-27

Focused-beam flat-sample method (FFM) is a new trial for synchrotron powder diffraction method, which is a combination of beam focusing optics, flat shape powder sample and area detectors. The method has advantages for X-ray diffraction experiments applying anomalous scattering effect (anomalous diffraction), because of 1. Absorption correction without approximation, 2. High intensity X-rays of focused incident beams and high signal noise ratio of diffracted X-rays 3. Rapid data collection with area detectors. We applied the FFM to anomalous diffraction experiments and collected synchrotron X-ray powder diffraction data of CoFe{sub 2}O{sub 4} (inverse spinel structure) using X-rays near Fe K absorptionmore » edge, which can distinguish Co and Fe by anomalous scattering effect. We conducted Rietveld analyses with the obtained powder diffraction data and successfully determined the distribution of Co and Fe ions in CoFe{sub 2}O{sub 4} crystal structure.« less

Treatment of addiction to ethanol and addictive-related behavior

DOEpatents

Dewey, Stephen L.; Brodie, Jonathan D.; Ashby, Jr., Charles R.

2001-01-01

The present invention provides a highly efficient method for treating alcohol addiction and for changing addiction-related behavior of a mammal suffering from alcohol addiction. The method includes administering to a mammal an effective amount of gamma vinylGABA or a pharmaceutically acceptable salt thereof. In one embodiment, the method of the present invention includes administering to the mammal an effective amount of a composition which increase central nervous system GABA levels wherein the effective amount is sufficient to diminish, inhibit or eliminate behavior associated with craving or use of alcohol.

Analysis of fuel using the Direct LSC method determination of bio-originated fuel in the presence of quenching

DOE PAGES

Doll, Charles G.; Wright, Cherylyn W.; Morley, Shannon M.; ...

2017-02-01

In this paper, a modified version of the Direct LSC method to correct for quenching effect was investigated for the determination of bio-originated fuel content in fuel samples produced from multiple biological starting materials. The modified method was found to be accurate in determining the percent bio-originated fuel to within 5% of the actual value for samples with quenching effects ≤43%. Finally, analysis of highly quenched samples was possible when diluted with the exception of one sample with a 100% quenching effect.

Analysis of fuel using the Direct LSC method determination of bio-originated fuel in the presence of quenching

DOE Office of Scientific and Technical Information (OSTI.GOV)

Doll, Charles G.; Wright, Cherylyn W.; Morley, Shannon M.

A modified version of the Direct LSC method to correct for quenching effect was investigated for the determination of bio-originated fuel content in fuel samples produced from multiple biological starting materials. The modified method was found to be accurate in determining the percent bio-originated fuel to within 5% of the actual value for samples with quenching effects ≤43%. Analysis of highly quenched samples was possible when diluted with the exception of one sample with a 100% quenching effect.

Numerical method of carbon-based material ablation effects on aero-heating for half-sphere

NASA Astrophysics Data System (ADS)

Wang, Jiang-Feng; Li, Jia-Wei; Zhao, Fa-Ming; Fan, Xiao-Feng

2018-05-01

A numerical method of aerodynamic heating with material thermal ablation effects for hypersonic half-sphere is presented. A surface material ablation model is provided to analyze the ablation effects on aero-thermal properties and structural heat conduction for thermal protection system (TPS) of hypersonic vehicles. To demonstrate its capability, applications for thermal analysis of hypersonic vehicles using carbonaceous ceramic ablators are performed and discussed. The numerical results show the high efficiency and validation of the method developed in thermal characteristics analysis of hypersonic aerodynamic heating.

Analysis of fuel using the Direct LSC method determination of bio-originated fuel in the presence of quenching

DOE Office of Scientific and Technical Information (OSTI.GOV)

Doll, Charles G.; Wright, Cherylyn W.; Morley, Shannon M.

In this paper, a modified version of the Direct LSC method to correct for quenching effect was investigated for the determination of bio-originated fuel content in fuel samples produced from multiple biological starting materials. The modified method was found to be accurate in determining the percent bio-originated fuel to within 5% of the actual value for samples with quenching effects ≤43%. Finally, analysis of highly quenched samples was possible when diluted with the exception of one sample with a 100% quenching effect.

Global transcriptomic profiling using small volumes of whole blood: a cost-effective method for translational genomic biomarker identification in small animals.

PubMed

Fricano, Meagan M; Ditewig, Amy C; Jung, Paul M; Liguori, Michael J; Blomme, Eric A G; Yang, Yi

2011-01-01

Blood is an ideal tissue for the identification of novel genomic biomarkers for toxicity or efficacy. However, using blood for transcriptomic profiling presents significant technical challenges due to the transcriptomic changes induced by ex vivo handling and the interference of highly abundant globin mRNA. Most whole blood RNA stabilization and isolation methods also require significant volumes of blood, limiting their effective use in small animal species, such as rodents. To overcome these challenges, a QIAzol-based RNA stabilization and isolation method (QSI) was developed to isolate sufficient amounts of high quality total RNA from 25 to 500 μL of rat whole blood. The method was compared to the standard PAXgene Blood RNA System using blood collected from rats exposed to saline or lipopolysaccharide (LPS). The QSI method yielded an average of 54 ng total RNA per μL of rat whole blood with an average RNA Integrity Number (RIN) of 9, a performance comparable with the standard PAXgene method. Total RNA samples were further processed using the NuGEN Ovation Whole Blood Solution system and cDNA was hybridized to Affymetrix Rat Genome 230 2.0 Arrays. The microarray QC parameters using RNA isolated with the QSI method were within the acceptable range for microarray analysis. The transcriptomic profiles were highly correlated with those using RNA isolated with the PAXgene method and were consistent with expected LPS-induced inflammatory responses. The present study demonstrated that the QSI method coupled with NuGEN Ovation Whole Blood Solution system is cost-effective and particularly suitable for transcriptomic profiling of minimal volumes of whole blood, typical of those obtained with small animal species.

A novel method to prepare L-Arabinose from xylose mother liquor by yeast-mediated biopurification

PubMed Central

2011-01-01

Background L-arabinose is an important intermediate for anti-virus drug synthesis and has also been used in food additives for diets-controlling in recent years. Commercial production of L-arabinose is a complex progress consisting of acid hydrolysis of gum arabic, followed by multiple procedures of purification, thus making high production cost. Therefore, there is a biotechnological and commercial interest in the development of new cost-effective and high-performance methods for obtaining high purity grade L-arabinose. Results An alternative, economical method for purifying L-arabinose from xylose mother liquor was developed in this study. After screening 306 yeast strains, a strain of Pichia anomala Y161 was selected as it could effectively metabolize other sugars but not L-arabinose. Fermentation in a medium containing xylose mother liquor permitted enrichment of L-arabinose by a significant depletion of other sugars. Biochemical analysis of this yeast strain confirmed that its poor capacity for utilizing L-arabinose was due to low activities of the enzymes required for the metabolism of this sugar. Response surface methodology was employed for optimization the fermentation conditions in shake flask cultures. The optimum conditions were: 75 h fermentation time, at 32.5°C, in a medium containing 21% (v/v) xylose mother liquor. Under these conditions, the highest purity of L-arabinose reached was 86.1% of total sugar, facilitating recovery of white crystalline L-arabinose from the fermentation medium by simple methods. Conclusion Yeast-mediated biopurification provides a dynamic method to prepare high purity of L-arabinose from the feedstock solution xylose mother liqour, with cost-effective and high-performance properties. PMID:21649890

Dent detection method by high gradation photometric stereo

NASA Astrophysics Data System (ADS)

Hasebe, Akihisa; Kato, Kunihito; Tanahashi, Hideki; Kubota, Naoki

2017-03-01

This paper describes an automatic detection method for small dents on a metal plate. We adopted the photometric stereo as a three-dimensional measurement method, which has advantages in terms of low cost and short measurement time. In addition, a high precision measurement system was realized by using an 18bit camera. Furthermore, the small dent on the surface of the metal plate is detected by the inner product of the measured normal vectors using photometric stereo. Finally, the effectiveness of our method was confirmed by detection experiments.

Effects of High School Students' Perceptions of School Life Quality on Their Academic Motivation Levels

ERIC Educational Resources Information Center

Akin Kösterelioglu, Meltem; Kösterelioglu, Ilker

2015-01-01

This study aims to identify the effects of high school students' perceptions of school life quality on their academic motivation levels. The study was conducted on a sample of high school students (n = 2371) in Amasya Province in the fall semester of 2013-2014 academic year. Study sample was selected with the help of cluster sampling method. Data…

[Rational method of obtaining sera with a high titre of virus-neutralizing antibodies. Report 2].

PubMed

Kravchenko, A T; Omel'chenko, T N; Tsetlin, E M

1978-02-01

In addition to report I (ZHMEI, 1977, No. 1) a study was made of 9 more schemes of rabbit immunization with the poliomyelitis virus, type I, for the purpose of obtaining the neutralizing sera of high titre. Vitamins A and C were used in the experiments in the capacity of the activators of the organism reaction; Freund's adjuvant of different make was tested; different reimmunization periods and different amounts of the adjuvant were administered. Titration of rabbit sera in the process of immunization and reimmunization showed immunization into the lymph nodes with the subsequent single reimmunization in one month to be the most effective and economical method of obtaining high effective sera.

Comparison of the effects on dynamic balance and aerobic capacity between objective and subjective methods of high-intensity robot-assisted gait training in chronic stroke patients: a randomized controlled trial.

PubMed

Bae, Young-Hyeon; Lee, Suk Min; Ko, Mansoo

2017-05-01

Robot-assisted gait training (RAGT) is effective for improving dynamic balance and aerobic capacity, but previous RAGT method does not set suitable training intensity. Recently, high-intensity treadmill gait training at 70% of heart rate reserve (HRR) was used for improving aerobic capacity and dynamic balance. This study was designed to compare the effectiveness between objective and subjective methods of high-intensity RAGT for improving dynamic balance and aerobic capacity in chronic stroke. Subjects were randomly allocated into experimental (n = 17) and control (n = 17) groups. The experimental group underwent high-intensity RAGT at 70% of HRR, whereas the control group underwent high-intensity RAGT at an RPE of 15. Both groups received their assigned training for 30 min per session, 3 days per week for 6 weeks. All subjects also received an additional 30 min of conventional physical therapy. Before and after each of the 18 sessions, the dynamic balance and aerobic capacity of all subjects were evaluated by a blinded examiner. After training, Berg Balance Scale (BBS) and Timed Up and Go Test scores, VO 2 max, and VO 2 max/kg were significantly increased in both groups (p < 0.05). These variables in experimental group were significantly greater than control group. However, the BBS score was not significantly different between both groups. All subjects completed high-intensity RAGT. No adverse effect of training was observed in both groups. High-intensity RAGT at 70% of HRR significantly improved dynamic balance and aerobic capacity more than RAGT at RPE of 15. These results suggest that high-intensity RAGT at 70% of HRR is safe and effective for improving dynamic balance and aerobic capacity in chronic stroke.

Investigation into shrinkage of high-performance concrete used for Iowa bridge decks and overlays.

DOT National Transportation Integrated Search

2013-09-01

High-performance concrete (HPC) overlays have been used increasingly as an effective and economical method for bridge decks in Iowa and other states. However, due to its high cementitious material content, HPC often displays high shrinkage cracking p...

Application of a Dense Gas Technique for Sterilizing Soft Biomaterials

PubMed Central

Karajanagi, Sandeep S.; Yoganathan, Roshan; Mammucari, Raffaella; Park, Hyoungshin; Cox, Julian; Zeitels, Steven M.; Langer, Robert; Foster, Neil R.

2017-01-01

Sterilization of soft biomaterials such as hydrogels is challenging because existing methods such as gamma irradiation, steam sterilization, or ethylene oxide sterilization, while effective at achieving high sterility assurance levels (SAL), may compromise their physicochemical properties and biocompatibility. New methods that effectively sterilize soft biomaterials without compromising their properties are therefore required. In this report, a dense-carbon dioxide (CO2)-based technique was used to sterilize soft polyethylene glycol (PEG)-based hydrogels while retaining their structure and physicochemical properties. Conventional sterilization methods such as gamma irradiation and steam sterilization severely compromised the structure of the hydrogels. PEG hydrogels with high water content and low elastic shear modulus (a measure of stiffness) were deliberately inoculated with bacteria and spores and then subjected to dense CO2. The dense CO2-based methods effectively sterilized the hydrogels achieving a SAL of 10−7 without compromising the viscoelastic properties, pH, water-content, and structure of the gels. Furthermore, dense CO2-treated gels were biocompatible and non-toxic when implanted subcutaneously in ferrets. The application of novel dense CO2-based methods to sterilize soft biomaterials has implications in developing safe sterilization methods for soft biomedical implants such as dermal fillers and viscosupplements. PMID:21337339

The multi-line slope method for measuring the effective magnetic field of cool stars: an application to the solar-like cycle of ɛ Eri

NASA Astrophysics Data System (ADS)

Scalia, C.; Leone, F.; Gangi, M.; Giarrusso, M.; Stift, M. J.

2017-12-01

One method for the determination of integrated longitudinal stellar fields from low-resolution spectra is the so-called slope method, which is based on the regression of the Stokes V signal against the first derivative of Stokes I. Here we investigate the possibility of extending this technique to measure the magnetic fields of cool stars from high-resolution spectra. For this purpose we developed a multi-line modification to the slope method, called the multi-line slope method. We tested this technique by analysing synthetic spectra computed with the COSSAM code and real observations obtained with the high-resolution spectropolarimeters Narval, HARPSpol and the Catania Astrophysical Observatory Spectropolarimeter (CAOS). We show that the multi-line slope method is a fast alternative to the least squares deconvolution technique for the measurement of the effective magnetic fields of cool stars. Using a Fourier transform on the effective magnetic field variations of the star ε Eri, we find that the long-term periodicity of the field corresponds to the 2.95-yr period of the stellar dynamo, revealed by the variation of the activity index.

A review of traditional and current methods used to potentially reduce toxicity of Aconitum roots in Traditional Chinese Medicine.

PubMed

Liu, Shuai; Li, Fei; Li, Yan; Li, Weifei; Xu, Jinkai; Du, Hong

2017-07-31

Aconitum species are well-known for their medicinal value and high lethal toxicity in many Asian countries, notably China, India and Japan. The tubers are only used after processing in Traditional Chinese Medicine (TCM). They can be used safely and effectively with the methods of decoction, rational compatibility, and correct processing based on traditional experiences and new technologies. However, high toxicological risks still remain due to improper preparation and usage in China and other countries. Therefore, there is a need to clarify the methods of processing and compatibility to ensure their effectiveness and minimize the potential risks. The aim of this paper is to provide a review of traditional and current methods used to potentially reduce toxicity of Aconitum roots in TCM. The use of Aconitum has been investigated and the methods of processing and compatibility throughout history, including recent research, have been reviewed. Using of the methods of rational preparation, reasonable compatibility, and proper processing based on traditional experiences and new technologies, can enable Aconitum to be used safely and effectively. Copyright © 2017 Elsevier Ireland Ltd. All rights reserved.

Collaborative simulation method with spatiotemporal synchronization process control

NASA Astrophysics Data System (ADS)

Zou, Yisheng; Ding, Guofu; Zhang, Weihua; Zhang, Jian; Qin, Shengfeng; Tan, John Kian

2016-10-01

When designing a complex mechatronics system, such as high speed trains, it is relatively difficult to effectively simulate the entire system's dynamic behaviors because it involves multi-disciplinary subsystems. Currently,a most practical approach for multi-disciplinary simulation is interface based coupling simulation method, but it faces a twofold challenge: spatial and time unsynchronizations among multi-directional coupling simulation of subsystems. A new collaborative simulation method with spatiotemporal synchronization process control is proposed for coupling simulating a given complex mechatronics system across multiple subsystems on different platforms. The method consists of 1) a coupler-based coupling mechanisms to define the interfacing and interaction mechanisms among subsystems, and 2) a simulation process control algorithm to realize the coupling simulation in a spatiotemporal synchronized manner. The test results from a case study show that the proposed method 1) can certainly be used to simulate the sub-systems interactions under different simulation conditions in an engineering system, and 2) effectively supports multi-directional coupling simulation among multi-disciplinary subsystems. This method has been successfully applied in China high speed train design and development processes, demonstrating that it can be applied in a wide range of engineering systems design and simulation with improved efficiency and effectiveness.

Residual vibration control based on a global search method in a high-speed white light scanning interferometer.

PubMed

Song, Zhenyuan; Guo, Tong; Fu, Xing; Hu, Xiaotang

2018-05-01

To achieve high-speed measurements using white light scanning interferometers, the scanning devices used need to have high feedback gain in closed-loop operations. However, flexure hinges induce a residual vibration that can cause a misidentification of the fringe order. The reduction of this residual vibration is crucial because the highly nonlinear distortions in interferograms lead to clearly incorrect measured profiles. Input shaping can be used to control the amplitude of the residual vibration. The conventional method uses continuous wavelet transform (CWT) to estimate parameters of the scanning device. Our proposed method extracts equivalent modal parameters using a global search algorithm. Due to its simplicity, ease of implementation, and response speed, this global search method outperforms CWT. The delay time is shortened by searching, because fewer modes are needed for the shaper. The effectiveness of the method has been confirmed by the agreement between simulated shaped responses and experimental displacement information from the capacitive sensor inside the scanning device, and the intensity profiles of the interferometer have been greatly improved. An experiment measuring the surface of a silicon wafer is also presented. The method is shown to be effective at improving the intensity profiles and recovering accurate surface topography. Finally, frequency localizations are found to be almost stable with different proportional gains, but their energy distributions change.

Dietary maifanite supplementation did not affect the apparent total tract digestibility of calcium and phosphorus in growing pigs

PubMed Central

Bai, Li Li; Ming, Dong Xu; Dong, Shu Ren; Yang, Zhong Yue; Wang, Wen Hui; Zhang, Shuai; Piao, Xiang Shu

2018-01-01

Objective This study was conducted to determine the effects of dietary maifanite supplementation and fecal collection method on the apparent total tract digestibility (ATTD) of calcium (Ca) and phosphorus (P) and blood parameters in growing pigs. Methods Thirty-six growing barrows (Duroc×Landrace×Yorkshire; 27.0±2.6 kg) were allotted to six dietary treatments with 6 pigs per treatment according to body weight in a completely randomized design. The experimental treatments were: i) Low Ca+cornstarch (2.25%), ii) Low Ca+maifanite (2.25%), iii) Medium Ca+cornstarch (1.42%), iv) Medium Ca+maifanite (1.42%), v) High Ca+cornstarch (0.64%), and vi) High Ca+maifanite (0.64%). Feces were collected by the total collection (TC) and indicator method (IM). At the beginning and the end of the experiment, blood samples were collected from each pig. Results For the TC method, there were no difference in Ca intake, fecal Ca output, Ca retention and the ATTD of Ca between cornstarch and maifanite diets at the same dietary Ca level. However, urinary Ca excretion was lower (p = 0.01) in pigs fed low Ca diets without maifanite supplementation compared with other dietary treatments. Dietary maifanite supplementation had no effect on the P metabolism in growing pigs. For the IM method, there was no difference in Ca digestibility between cornstarch and maifanite diets at the same dietary Ca level. The ATTD of P was greater (p<0.01) in pigs fed the high Ca diet with maifanite supplementation compared with the high Ca diet with cornstarch treatment. Dietary inclusion of maifanite had no effect on blood parameters in growing pigs. Conclusion Dietary maifanite supplementation had no effect on the ATTD of Ca and P and serum parameters in growing pigs. The IM resulted in lower digestibility values than the TC method. PMID:28728391

A Selective Overview of Variable Selection in High Dimensional Feature Space

PubMed Central

Fan, Jianqing

2010-01-01

High dimensional statistical problems arise from diverse fields of scientific research and technological development. Variable selection plays a pivotal role in contemporary statistical learning and scientific discoveries. The traditional idea of best subset selection methods, which can be regarded as a specific form of penalized likelihood, is computationally too expensive for many modern statistical applications. Other forms of penalized likelihood methods have been successfully developed over the last decade to cope with high dimensionality. They have been widely applied for simultaneously selecting important variables and estimating their effects in high dimensional statistical inference. In this article, we present a brief account of the recent developments of theory, methods, and implementations for high dimensional variable selection. What limits of the dimensionality such methods can handle, what the role of penalty functions is, and what the statistical properties are rapidly drive the advances of the field. The properties of non-concave penalized likelihood and its roles in high dimensional statistical modeling are emphasized. We also review some recent advances in ultra-high dimensional variable selection, with emphasis on independence screening and two-scale methods. PMID:21572976

Characterization of matrix effects in developing rugged high-throughput LC-MS/MS methods for bioanalysis.

PubMed

Li, Fumin; Wang, Jun; Jenkins, Rand

2016-05-01

There is an ever-increasing demand for high-throughput LC-MS/MS bioanalytical assays to support drug discovery and development. Matrix effects of sofosbuvir (protonated) and paclitaxel (sodiated) were thoroughly evaluated using high-throughput chromatography (defined as having a run time ≤1 min) under 14 elution conditions with extracts from protein precipitation, liquid-liquid extraction and solid-phase extraction. A slight separation, in terms of retention time, between underlying matrix components and sofosbuvir/paclitaxel can greatly alleviate matrix effects. High-throughput chromatography, with proper optimization, can provide rapid and effective chromatographic separation under 1 min to alleviate matrix effects and enhance assay ruggedness for regulated bioanalysis.

Design method of high-efficient 
LED headlamp lens.

PubMed

Chen, Fei; Wang, Kai; Qin, Zong; Wu, Dan; Luo, Xiaobing; Liu, Sheng

2010-09-27

Low optical efficiency of light-emitting diode (LED) based headlamp is one of the most important issues to obstruct applications of LEDs in headlamp. An effective high-efficient LED headlamp freeform lens design method is introduced in this paper. A low-beam lens and a high-beam lens for LED headlamp are designed according to this method. Monte Carlo ray tracing simulation results demonstrate that the LED headlamp with these two lenses can fully comply with the ECE regulation without any other lens or reflector. Moreover, optical efficiencies of both these two lenses are more than 88% in theory.

Quantitative digital image analysis of chromogenic assays for high throughput screening of alpha-amylase mutant libraries.

PubMed

Shankar, Manoharan; Priyadharshini, Ramachandran; Gunasekaran, Paramasamy

2009-08-01

An image analysis-based method for high throughput screening of an alpha-amylase mutant library using chromogenic assays was developed. Assays were performed in microplates and high resolution images of the assay plates were read using the Virtual Microplate Reader (VMR) script to quantify the concentration of the chromogen. This method is fast and sensitive in quantifying 0.025-0.3 mg starch/ml as well as 0.05-0.75 mg glucose/ml. It was also an effective screening method for improved alpha-amylase activity with a coefficient of variance of 18%.

Modelling cost-effectiveness of different vasectomy methods in India, Kenya, and Mexico

PubMed Central

Seamans, Yancy; Harner-Jay, Claudia M

2007-01-01

Background Vasectomy is generally considered a safe and effective method of permanent contraception. The historical effectiveness of vasectomy has been questioned by recent research results indicating that the most commonly used method of vasectomy – simple ligation and excision (L and E) – appears to have a relatively high failure rate, with reported pregnancy rates as high as 4%. Updated methods such as fascial interposition (FI) and thermal cautery can lower the rate of failure but may require additional financial investments and may not be appropriate for low-resource clinics. In order to better compare the cost-effectiveness of these different vasectomy methods, we modelled the costs of different vasectomy methods using cost data collected in India, Kenya, and Mexico and effectiveness data from the latest published research. Methods The costs associated with providing vasectomies were determined in each country through interviews with clinic staff. Costs collected were economic, direct, programme costs of fixed vasectomy services but did not include large capital expenses or general recurrent costs for the health care facility. Estimates of the time required to provide service were gained through interviews and training costs were based on the total costs of vasectomy training programmes in each country. Effectiveness data were obtained from recent published studies and comparative cost-effectiveness was determined using cost per couple years of protection (CYP). Results In each country, the labour to provide the vasectomy and follow-up services accounts for the greatest portion of the overall cost. Because each country almost exclusively used one vasectomy method at all of the clinics included in the study, we modelled costs based on the additional material, labour, and training costs required in each country. Using a model of a robust vasectomy program, more effective methods such as FI and thermal cautery reduce the cost per CYP of a vasectomy by $0.08 – $0.55. Conclusion Based on the results presented, more effective methods of vasectomy – including FI, thermal cautery, and thermal cautery combined with FI – are more cost-effective than L and E alone. Analysis shows that for a programme in which a minimum of 20 clients undergo vasectomies per month, the cost per CYP is reduced in all three countries by updated vasectomy methods. PMID:17629921

Radio spectra of bright compact sources at z > 4.5

NASA Astrophysics Data System (ADS)

Coppejans, Rocco; van Velzen, Sjoert; Intema, Huib T.; Müller, Cornelia; Frey, Sándor; Coppejans, Deanne L.; Cseh, Dávid; Williams, Wendy L.; Falcke, Heino; Körding, Elmar G.; Orrú, Emanuela; Paragi, Zsolt; Gabányi, Krisztina É.

2017-05-01

High-redshift quasars are important to study galaxy and active galactic nuclei evolution, test cosmological models and study supermassive black hole growth. Optical searches for high-redshift sources have been very successful, but radio searches are not hampered by dust obscuration and should be more effective at finding sources at even higher redshifts. Identifying high-redshift sources based on radio data is, however, not trivial. Here we report on new multifrequency Giant Metrewave Radio Telescope observations of eight z > 4.5 sources previously studied at high angular resolution with very long baseline interferometry (VLBI). Combining these observations with those from the literature, we construct broad-band radio spectra of all 30 z > 4.5 sources that have been observed with VLBI. In the sample we found flat, steep and peaked spectra in approximately equal proportions. Despite several selection effects, we conclude that the z > 4.5 VLBI (and likely also non-VLBI) sources have diverse spectra and that only about a quarter of the sources in the sample have flat spectra. Previously, the majority of high-redshift radio sources were identified based on their ultrasteep spectra. Recently, a new method has been proposed to identify these objects based on their megahertz-peaked spectra. No method would have identified more than 18 per cent of the high-redshift sources in this sample. More effective methods are necessary to reliably identify complete samples of high-redshift sources based on radio data.

Research on fusion algorithm of polarization image in tetrolet domain

NASA Astrophysics Data System (ADS)

Zhang, Dexiang; Yuan, BaoHong; Zhang, Jingjing

2015-12-01

Tetrolets are Haar-type wavelets whose supports are tetrominoes which are shapes made by connecting four equal-sized squares. A fusion method for polarization images based on tetrolet transform is proposed. Firstly, the magnitude of polarization image and angle of polarization image can be decomposed into low-frequency coefficients and high-frequency coefficients with multi-scales and multi-directions using tetrolet transform. For the low-frequency coefficients, the average fusion method is used. According to edge distribution differences in high frequency sub-band images, for the directional high-frequency coefficients are used to select the better coefficients by region spectrum entropy algorithm for fusion. At last the fused image can be obtained by utilizing inverse transform for fused tetrolet coefficients. Experimental results show that the proposed method can detect image features more effectively and the fused image has better subjective visual effect

Digital micromirror device camera with per-pixel coded exposure for high dynamic range imaging.

PubMed

Feng, Wei; Zhang, Fumin; Wang, Weijing; Xing, Wei; Qu, Xinghua

2017-05-01

In this paper, we overcome the limited dynamic range of the conventional digital camera, and propose a method of realizing high dynamic range imaging (HDRI) from a novel programmable imaging system called a digital micromirror device (DMD) camera. The unique feature of the proposed new method is that the spatial and temporal information of incident light in our DMD camera can be flexibly modulated, and it enables the camera pixels always to have reasonable exposure intensity by DMD pixel-level modulation. More importantly, it allows different light intensity control algorithms used in our programmable imaging system to achieve HDRI. We implement the optical system prototype, analyze the theory of per-pixel coded exposure for HDRI, and put forward an adaptive light intensity control algorithm to effectively modulate the different light intensity to recover high dynamic range images. Via experiments, we demonstrate the effectiveness of our method and implement the HDRI on different objects.

Wind Turbine Diagnosis under Variable Speed Conditions Using a Single Sensor Based on the Synchrosqueezing Transform Method.

PubMed

Guo, Yanjie; Chen, Xuefeng; Wang, Shibin; Sun, Ruobin; Zhao, Zhibin

2017-05-18

The gearbox is one of the key components in wind turbines. Gearbox fault signals are usually nonstationary and highly contaminated with noise. The presence of amplitude-modulated and frequency-modulated (AM-FM) characteristics compound the difficulty of precise fault diagnosis of wind turbines, therefore, it is crucial to develop an effective fault diagnosis method for such equipment. This paper presents an improved diagnosis method for wind turbines via the combination of synchrosqueezing transform and local mean decomposition. Compared to the conventional time-frequency analysis techniques, the improved method which is performed in non-real-time can effectively reduce the noise pollution of the signals and preserve the signal characteristics, and hence is suitable for the analysis of nonstationary signals with high noise. This method is further validated by simulated signals and practical vibration data measured from a 1.5 MW wind turbine. The results confirm that the proposed method can simultaneously control the noise and increase the accuracy of time-frequency representation.

Wind Turbine Diagnosis under Variable Speed Conditions Using a Single Sensor Based on the Synchrosqueezing Transform Method

PubMed Central

Guo, Yanjie; Chen, Xuefeng; Wang, Shibin; Sun, Ruobin; Zhao, Zhibin

2017-01-01

The gearbox is one of the key components in wind turbines. Gearbox fault signals are usually nonstationary and highly contaminated with noise. The presence of amplitude-modulated and frequency-modulated (AM-FM) characteristics compound the difficulty of precise fault diagnosis of wind turbines, therefore, it is crucial to develop an effective fault diagnosis method for such equipment. This paper presents an improved diagnosis method for wind turbines via the combination of synchrosqueezing transform and local mean decomposition. Compared to the conventional time-frequency analysis techniques, the improved method which is performed in non-real-time can effectively reduce the noise pollution of the signals and preserve the signal characteristics, and hence is suitable for the analysis of nonstationary signals with high noise. This method is further validated by simulated signals and practical vibration data measured from a 1.5 MW wind turbine. The results confirm that the proposed method can simultaneously control the noise and increase the accuracy of time-frequency representation. PMID:28524090

Effect of Forced Sexual Intercourse on Associations between Early Sexual Debut and Other Health Risk Behaviors among US High School Students

ERIC Educational Resources Information Center

Lowry, Richard; Robin, Leah; Kann, Laura

2017-01-01

Background: Previous research on associations between early sexual debut and other health risk behaviors has not examined the effect of forced sexual intercourse on those associations. Methods: We analyzed data from a nationally representative sample of 19,240 high school students in the United States, age =16 years, to describe the effect of…

High quality x-ray absorption spectroscopy measurements with long energy range at high pressure using diamond anvil cell.

PubMed

Hong, Xinguo; Newville, Matthew; Prakapenka, Vitali B; Rivers, Mark L; Sutton, Stephen R

2009-07-01

We describe an approach for acquiring high quality x-ray absorption fine structure (XAFS) spectroscopy spectra with wide energy range at high pressure using diamond anvil cell (DAC). Overcoming the serious interference of diamond Bragg peaks is essential for combining XAFS and DAC techniques in high pressure research, yet an effective method to obtain accurate XAFS spectrum free from DAC induced glitches has been lacking. It was found that these glitches, whose energy positions are very sensitive to the relative orientation between DAC and incident x-ray beam, can be effectively eliminated using an iterative algorithm based on repeated measurements over a small angular range of DAC orientation, e.g., within +/-3 degrees relative to the x-ray beam direction. Demonstration XAFS spectra are reported for rutile-type GeO2 recorded by traditional ambient pressure and high pressure DAC methods, showing similar quality at 440 eV above the absorption edge. Accurate XAFS spectra of GeO2 glass were obtained at high pressure up to 53 GPa, providing important insight into the structural polymorphism of GeO2 glass at high pressure. This method is expected be applicable for in situ XAFS measurements using a diamond anvil cell up to ultrahigh pressures.

High quality x-ray absorption spectroscopy measurements with long energy range at high pressure using diamond anvil cell

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hong, X.; Newville, M.; Prakapenka, V.B.

We describe an approach for acquiring high quality x-ray absorption fine structure (XAFS) spectroscopy spectra with wide energy range at high pressure using diamond anvil cell (DAC). Overcoming the serious interference of diamond Bragg peaks is essential for combining XAFS and DAC techniques in high pressure research, yet an effective method to obtain accurate XAFS spectrum free from DAC induced glitches has been lacking. It was found that these glitches, whose energy positions are very sensitive to the relative orientation between DAC and incident x-ray beam, can be effectively eliminated using an iterative algorithm based on repeated measurements over amore » small angular range of DAC orientation, e.g., within {+-}3{sup o} relative to the x-ray beam direction. Demonstration XAFS spectra are reported for rutile-type GeO{sub 2} recorded by traditional ambient pressure and high pressure DAC methods, showing similar quality at 440 eV above the absorption edge. Accurate XAFS spectra of GeO{sub 2} glass were obtained at high pressure up to 53 GPa, providing important insight into the structural polymorphism of GeO{sub 2} glass at high pressure. This method is expected be applicable for in situ XAFS measurements using a diamond anvil cell up to ultrahigh pressures.« less

Systematic Assessment of Seven Solvent and Solid-Phase Extraction Methods for Metabolomics Analysis of Human Plasma by LC-MS

NASA Astrophysics Data System (ADS)

Sitnikov, Dmitri G.; Monnin, Cian S.; Vuckovic, Dajana

2016-12-01

The comparison of extraction methods for global metabolomics is usually executed in biofluids only and focuses on metabolite coverage and method repeatability. This limits our detailed understanding of extraction parameters such as recovery and matrix effects and prevents side-by-side comparison of different sample preparation strategies. To address this gap in knowledge, seven solvent-based and solid-phase extraction methods were systematically evaluated using standard analytes spiked into both buffer and human plasma. We compared recovery, coverage, repeatability, matrix effects, selectivity and orthogonality of all methods tested for non-lipid metabolome in combination with reversed-phased and mixed-mode liquid chromatography mass spectrometry analysis (LC-MS). Our results confirmed wide selectivity and excellent precision of solvent precipitations, but revealed their high susceptibility to matrix effects. The use of all seven methods showed high overlap and redundancy which resulted in metabolite coverage increases of 34-80% depending on LC-MS method employed as compared to the best single extraction protocol (methanol/ethanol precipitation) despite 7x increase in MS analysis time and sample consumption. The most orthogonal methods to methanol-based precipitation were ion-exchange solid-phase extraction and liquid-liquid extraction using methyl-tertbutyl ether. Our results help facilitate rational design and selection of sample preparation methods and internal standards for global metabolomics.

Systematic Assessment of Seven Solvent and Solid-Phase Extraction Methods for Metabolomics Analysis of Human Plasma by LC-MS

PubMed Central

Sitnikov, Dmitri G.; Monnin, Cian S.; Vuckovic, Dajana

2016-01-01

The comparison of extraction methods for global metabolomics is usually executed in biofluids only and focuses on metabolite coverage and method repeatability. This limits our detailed understanding of extraction parameters such as recovery and matrix effects and prevents side-by-side comparison of different sample preparation strategies. To address this gap in knowledge, seven solvent-based and solid-phase extraction methods were systematically evaluated using standard analytes spiked into both buffer and human plasma. We compared recovery, coverage, repeatability, matrix effects, selectivity and orthogonality of all methods tested for non-lipid metabolome in combination with reversed-phased and mixed-mode liquid chromatography mass spectrometry analysis (LC-MS). Our results confirmed wide selectivity and excellent precision of solvent precipitations, but revealed their high susceptibility to matrix effects. The use of all seven methods showed high overlap and redundancy which resulted in metabolite coverage increases of 34–80% depending on LC-MS method employed as compared to the best single extraction protocol (methanol/ethanol precipitation) despite 7x increase in MS analysis time and sample consumption. The most orthogonal methods to methanol-based precipitation were ion-exchange solid-phase extraction and liquid-liquid extraction using methyl-tertbutyl ether. Our results help facilitate rational design and selection of sample preparation methods and internal standards for global metabolomics. PMID:28000704

An Improved Method of AGM for High Precision Geolocation of SAR Images

NASA Astrophysics Data System (ADS)

Zhou, G.; He, C.; Yue, T.; Huang, W.; Huang, Y.; Li, X.; Chen, Y.

2018-05-01

In order to take full advantage of SAR images, it is necessary to obtain the high precision location of the image. During the geometric correction process of images, to ensure the accuracy of image geometric correction and extract the effective mapping information from the images, precise image geolocation is important. This paper presents an improved analytical geolocation method (IAGM) that determine the high precision geolocation of each pixel in a digital SAR image. This method is based on analytical geolocation method (AGM) proposed by X. K. Yuan aiming at realizing the solution of RD model. Tests will be conducted using RADARSAT-2 SAR image. Comparing the predicted feature geolocation with the position as determined by high precision orthophoto, results indicate an accuracy of 50m is attainable with this method. Error sources will be analyzed and some recommendations about improving image location accuracy in future spaceborne SAR's will be given.

A high order semi-Lagrangian discontinuous Galerkin method for Vlasov-Poisson simulations without operator splitting

NASA Astrophysics Data System (ADS)

Cai, Xiaofeng; Guo, Wei; Qiu, Jing-Mei

2018-02-01

In this paper, we develop a high order semi-Lagrangian (SL) discontinuous Galerkin (DG) method for nonlinear Vlasov-Poisson (VP) simulations without operator splitting. In particular, we combine two recently developed novel techniques: one is the high order non-splitting SLDG transport method (Cai et al. (2017) [4]), and the other is the high order characteristics tracing technique proposed in Qiu and Russo (2017) [29]. The proposed method with up to third order accuracy in both space and time is locally mass conservative, free of splitting error, positivity-preserving, stable and robust for large time stepping size. The SLDG VP solver is applied to classic benchmark test problems such as Landau damping and two-stream instabilities for VP simulations. Efficiency and effectiveness of the proposed scheme is extensively tested. Tremendous CPU savings are shown by comparisons between the proposed SL DG scheme and the classical Runge-Kutta DG method.

A novel wide-field-of-view display method with higher central resolution for hyper-realistic head dome projector

NASA Astrophysics Data System (ADS)

Hotta, Aira; Sasaki, Takashi; Okumura, Haruhiko

2007-02-01

In this paper, we propose a novel display method to realize a high-resolution image in a central visual field for a hyper-realistic head dome projector. The method uses image processing based on the characteristics of human vision, namely, high central visual acuity and low peripheral visual acuity, and pixel shift technology, which is one of the resolution-enhancing technologies for projectors. The projected image with our method is a fine wide-viewing-angle image with high definition in the central visual field. We evaluated the psychological effects of the projected images with our method in terms of sensation of reality. According to the result, we obtained 1.5 times higher resolution in the central visual field and a greater sensation of reality by using our method.

The spa typing of methicillin-resistant Staphylococcus aureus isolates by High Resolution Melting (HRM) analysis.

PubMed

Fasihi, Yasser; Fooladi, Saba; Mohammadi, Mohammad Ali; Emaneini, Mohammad; Kalantar-Neyestanaki, Davood

2017-09-06

Molecular typing is an important tool for control and prevention of infection. A suitable molecular typing method for epidemiological investigation must be easy to perform, highly reproducible, inexpensive, rapid and easy to interpret. In this study, two molecular typing methods including the conventional PCR-sequencing method and high resolution melting (HRM) analysis were used for staphylococcal protein A (spa) typing of 30 Methicillin-resistant Staphylococcus aureus (MRSA) isolates recovered from clinical samples. Based on PCR-sequencing method results, 16 different spa types were identified among the 30 MRSA isolates. Among the 16 different spa types, 14 spa types separated by HRM method. Two spa types including t4718 and t2894 were not separated from each other. According to our results, spa typing based on HRM analysis method is very rapid, easy to perform and cost-effective, but this method must be standardized for different regions, spa types, and real-time machinery.

Optical characterization of high speed microscanners based on static slit profiling method

NASA Astrophysics Data System (ADS)

Alaa Elhady, A.; Sabry, Yasser M.; Khalil, Diaa

2017-01-01

Optical characterization of high-speed microscanners is a challenging task that usually requires special high speed, extremely expensive camera systems. This paper presents a novel simple method to characterize the scanned beam spot profile and size in high-speed optical scanners under operation. It allows measuring the beam profile and the spot sizes at different scanning angles. The method is analyzed theoretically and applied experimentally on the characterization of a Micro Electro Mechanical MEMS scanner operating at 2.6 kHz. The variation of the spot size versus the scanning angle, up to ±15°, is extracted and the dynamic bending curvature effect of the micromirror is predicted.

The Effective Practices and Beliefs of School Principals in High Achieving Hispanic Majority Mid-Level Schools

ERIC Educational Resources Information Center

Briseno, Johnny

2010-01-01

This qualitative phenomenological research study used narrative inquiry to investigate the effective practices and beliefs of 10 Texas principals in high achieving majority Hispanic mid-level schools. Participant interviews were analyzed using the Creswell (2007) six step method for analyzing phenomenological studies. Findings from this study…

An Investigation of Highly Effective Leaders in Outdoor Adventure Programs Using a Multi-Method Approach

ERIC Educational Resources Information Center

Hobbs, William D.

2009-01-01

Research on leadership in outdoor adventure programs has focused primarily on Educational and Outdoor Skills. Anecdotal and practical experience has suggested that the performance of highly effective leaders may depend instead on distinctive qualities and components closely tied to individual character--a perspective of transformational…

The Progressive Discipline Matrix and Its Effects on Discipline in High Schools

ERIC Educational Resources Information Center

Jones, Vincent L.

2017-01-01

The purpose of this mixed-method case study was to determine the effectiveness of the progressive discipline matrix in high schools in one Tennessee school district. The further intent was to investigate how discipline practices influenced the perceptions of teachers and administrators. Findings from quantitative data stated that progressive…

Optimized method for manufacturing large aspheric surfaces

NASA Astrophysics Data System (ADS)

Zhou, Xusheng; Li, Shengyi; Dai, Yifan; Xie, Xuhui

2007-12-01

Aspheric optics are being used more and more widely in modern optical systems, due to their ability of correcting aberrations, enhancing image quality, enlarging the field of view and extending the range of effect, while reducing the weight and volume of the system. With optical technology development, we have more pressing requirement to large-aperture and high-precision aspheric surfaces. The original computer controlled optical surfacing (CCOS) technique cannot meet the challenge of precision and machining efficiency. This problem has been thought highly of by researchers. Aiming at the problem of original polishing process, an optimized method for manufacturing large aspheric surfaces is put forward. Subsurface damage (SSD), full aperture errors and full band of frequency errors are all in control of this method. Lesser SSD depth can be gained by using little hardness tool and small abrasive grains in grinding process. For full aperture errors control, edge effects can be controlled by using smaller tools and amendment model with material removal function. For full band of frequency errors control, low frequency errors can be corrected with the optimized material removal function, while medium-high frequency errors by using uniform removing principle. With this optimized method, the accuracy of a K9 glass paraboloid mirror can reach rms 0.055 waves (where a wave is 0.6328μm) in a short time. The results show that the optimized method can guide large aspheric surface manufacturing effectively.

Global high-frequency source imaging accounting for complexity in Green's functions

NASA Astrophysics Data System (ADS)

Lambert, V.; Zhan, Z.

2017-12-01

The general characterization of earthquake source processes at long periods has seen great success via seismic finite fault inversion/modeling. Complementary techniques, such as seismic back-projection, extend the capabilities of source imaging to higher frequencies and reveal finer details of the rupture process. However, such high frequency methods are limited by the implicit assumption of simple Green's functions, which restricts the use of global arrays and introduces artifacts (e.g., sweeping effects, depth/water phases) that require careful attention. This motivates the implementation of an imaging technique that considers the potential complexity of Green's functions at high frequencies. We propose an alternative inversion approach based on the modest assumption that the path effects contributing to signals within high-coherency subarrays share a similar form. Under this assumption, we develop a method that can combine multiple high-coherency subarrays to invert for a sparse set of subevents. By accounting for potential variability in the Green's functions among subarrays, our method allows for the utilization of heterogeneous global networks for robust high resolution imaging of the complex rupture process. The approach also provides a consistent framework for examining frequency-dependent radiation across a broad frequency spectrum.

Preparation of nano-hydroxyapatite particles with different morphology and their response to highly malignant melanoma cells in vitro

NASA Astrophysics Data System (ADS)

Li, Bo; Guo, Bo; Fan, Hongsong; Zhang, Xingdong

2008-11-01

To investigate the effects of nano-hydroxyapatite (HA) particles with different morphology on highly malignant melanoma cells, three kinds of HA particles with different morphology were synthesized and co-cultured with highly malignant melanoma cells using phosphate-buffered saline (PBS) as control. A precipitation method with or without citric acid addition as surfactant was used to produce rod-like hydroxyapatite (HA) particles with nano- and micron size, respectively, and a novel oil-in-water emulsion method was employed to prepare ellipse-like nano-HA particles. Particle morphology and size distribution of the as prepared HA powders were characterized by transmission electron microscope (TEM) and dynamic light scattering technique. The nano- and micron HA particles with different morphology were co-cultured with highly malignant melanoma cells. Immunofluorescence analysis and MTT assay were employed to evaluate morphological change of nucleolus and proliferation of tumour cells, respectively. To compare the effects of HA particles on cell response, the PBS without HA particles was used as control. The experiment results indicated that particle nanoscale effect rather than particle morphology of HA was more effective for the inhibition on highly malignant melanoma cells proliferation.

Effects of High Intensity Interval Training on Increasing Explosive Power, Speed, and Agility

NASA Astrophysics Data System (ADS)

Fajrin, F.; Kusnanik, N. W.; Wijono

2018-01-01

High Intensity Interval Training (HIIT) is a type of exercise that combines high-intensity exercise and low intensity exercise in a certain time interval. This type of training is very effective and efficient to improve the physical components. The process of improving athletes achievement related to how the process of improving the physical components, so the selection of a good practice method will be very helpful. This study aims to analyze how is the effects of HIIT on increasing explosive power, speed, and agility. This type of research is quantitative with quasi-experimental methods. The design of this study used the Matching-Only Design, with data analysis using the t-test (paired sample t-test). After being given the treatment for six weeks, the results showed there are significant increasing in explosive power, speed, and agility. HIIT in this study used a form of exercise plyometric as high-intensity exercise and jogging as mild or moderate intensity exercise. Increase was due to the improvement of neuromuscular characteristics that affect the increase in muscle strength and performance. From the data analysis, researchers concluded that, Exercises of High Intensity Interval Training significantly effect on the increase in Power Limbs, speed, and agility.

Effect of Chemistry Triangle Oriented Learning Media on Cooperative, Individual and Conventional Method on Chemistry Learning Result

NASA Astrophysics Data System (ADS)

Latisma D, L.; Kurniawan, W.; Seprima, S.; Nirbayani, E. S.; Ellizar, E.; Hardeli, H.

2018-04-01

The purpose of this study was to see which method are well used with the Chemistry Triangle-oriented learning media. This quasi experimental research involves first grade of senior high school students in six schools namely each two SMA N in Solok city, in Pasaman and two SMKN in Pariaman. The sampling technique was done by Cluster Random Sampling. Data were collected by test and analyzed by one-way anova and Kruskall Wallish test. The results showed that the high school students in Solok learning taught by cooperative method is better than the results of student learning taught by conventional and Individual methods, both for students who have high initial ability and low-ability. Research in SMK showed that the overall student learning outcomes taught by conventional method is better than the student learning outcomes taught by cooperative and individual methods. Student learning outcomes that have high initial ability taught by individual method is better than student learning outcomes that are taught by cooperative method and for students who have low initial ability, there is no difference in student learning outcomes taught by cooperative, individual and conventional methods. Learning in high school in Pasaman showed no significant difference in learning outcomes of the three methods undertaken.

Influence of Mentoring on African American and Hispanic Males in High School

ERIC Educational Resources Information Center

Smith, Jacqueline A.

2016-01-01

The mixed method research study was designed to evaluate the effects on a mentoring initiative on 40 African American and Hispanic males in an urban high school. The study took place over a three-month period in a traditional public school with 2,000 students. Data collection methods used included individual interview with student mentees, surveys…

Non-parametric methods for cost-effectiveness analysis: the central limit theorem and the bootstrap compared.

PubMed

Nixon, Richard M; Wonderling, David; Grieve, Richard D

2010-03-01

Cost-effectiveness analyses (CEA) alongside randomised controlled trials commonly estimate incremental net benefits (INB), with 95% confidence intervals, and compute cost-effectiveness acceptability curves and confidence ellipses. Two alternative non-parametric methods for estimating INB are to apply the central limit theorem (CLT) or to use the non-parametric bootstrap method, although it is unclear which method is preferable. This paper describes the statistical rationale underlying each of these methods and illustrates their application with a trial-based CEA. It compares the sampling uncertainty from using either technique in a Monte Carlo simulation. The experiments are repeated varying the sample size and the skewness of costs in the population. The results showed that, even when data were highly skewed, both methods accurately estimated the true standard errors (SEs) when sample sizes were moderate to large (n>50), and also gave good estimates for small data sets with low skewness. However, when sample sizes were relatively small and the data highly skewed, using the CLT rather than the bootstrap led to slightly more accurate SEs. We conclude that while in general using either method is appropriate, the CLT is easier to implement, and provides SEs that are at least as accurate as the bootstrap. (c) 2009 John Wiley & Sons, Ltd.

Hybrid RANS-LES using high order numerical methods

NASA Astrophysics Data System (ADS)

Henry de Frahan, Marc; Yellapantula, Shashank; Vijayakumar, Ganesh; Knaus, Robert; Sprague, Michael

2017-11-01

Understanding the impact of wind turbine wake dynamics on downstream turbines is particularly important for the design of efficient wind farms. Due to their tractable computational cost, hybrid RANS/LES models are an attractive framework for simulating separation flows such as the wake dynamics behind a wind turbine. High-order numerical methods can be computationally efficient and provide increased accuracy in simulating complex flows. In the context of LES, high-order numerical methods have shown some success in predictions of turbulent flows. However, the specifics of hybrid RANS-LES models, including the transition region between both modeling frameworks, pose unique challenges for high-order numerical methods. In this work, we study the effect of increasing the order of accuracy of the numerical scheme in simulations of canonical turbulent flows using RANS, LES, and hybrid RANS-LES models. We describe the interactions between filtering, model transition, and order of accuracy and their effect on turbulence quantities such as kinetic energy spectra, boundary layer evolution, and dissipation rate. This work was funded by the U.S. Department of Energy, Exascale Computing Project, under Contract No. DE-AC36-08-GO28308 with the National Renewable Energy Laboratory.

Effect of seabed roughness on tidal current turbines

NASA Astrophysics Data System (ADS)

Gupta, Vikrant; Wan, Minping

2017-11-01

Tidal current turbines are shown to have potential to generate clean energy for a negligible environmental impact. These devices, however, operate in high to moderate current regions where the flow is highly turbulent. It has been shown in flume tank experiments at IFREMER in Boulogne-Sur-Mer (France) and NAFL in the University of Minnesota (US) that the level of turbulence and boundary layer profile affect a turbine's power output and wake characteristics. A major factor that determines these marine flow characteristics is the seabed roughness. Experiments, however, cannot simulate the high Reynolds number conditions of real marine flows. For that, we rely on numerical simulations. High accuracy numerical methods, such as DNS, of wall-bounded flows are very expensive, where the number of grid-points needed to resolve the flow varies as (Re) 9 / 4 (where Re is the flow Reynolds number). While numerically affordable RANS methods compromise on accuracy. Wall-modelled LES methods, which provide both accuracy and affordability, have been improved tremendously in the recent years. We discuss the application of such numerical methods for studying the effect of seabed roughness on marine flow features and their impact on turbine power output and wake characteristics. NSFC, Project Number 11672123.

Design of conduction cooling system for a high current HTS DC reactor

NASA Astrophysics Data System (ADS)

Dao, Van Quan; Kim, Taekue; Le Tat, Thang; Sung, Haejin; Choi, Jongho; Kim, Kwangmin; Hwang, Chul-Sang; Park, Minwon; Yu, In-Keun

2017-07-01

A DC reactor using a high temperature superconducting (HTS) magnet reduces the reactor’s size, weight, flux leakage, and electrical losses. An HTS magnet needs cryogenic cooling to achieve and maintain its superconducting state. There are two methods for doing this: one is pool boiling and the other is conduction cooling. The conduction cooling method is more effective than the pool boiling method in terms of smaller size and lighter weight. This paper discusses a design of conduction cooling system for a high current, high temperature superconducting DC reactor. Dimensions of the conduction cooling system parts including HTS magnets, bobbin structures, current leads, support bars, and thermal exchangers were calculated and drawn using a 3D CAD program. A finite element method model was built for determining the optimal design parameters and analyzing the thermo-mechanical characteristics. The operating current and inductance of the reactor magnet were 1,500 A, 400 mH, respectively. The thermal load of the HTS DC reactor was analyzed for determining the cooling capacity of the cryo-cooler. The study results can be effectively utilized for the design and fabrication of a commercial HTS DC reactor.

Research on the winding losses based on finite element method for transformer

NASA Astrophysics Data System (ADS)

Li, Wenpeng; Lai, Wenqing; Ye, Ligang; Luo, Hanwu; Luo, Changjiang; Cui, Shigang; Wang, Yongqiang

2018-04-01

Transformer loss can cause the transformer to overheat. Under the action of high frequency current, the loss of transformer windings will be aggravated due to proximity effect and skin effect. In this paper, a three-dimensional model of high frequency transformer windings is established. Considering of the proximity effect and skin effect, the eddy current effects loss in the transformer windings are simulated based on finite element method. And the winding losses of the transformer windings are obtained under different arrangements. The influence of the winding layout on the winding losses is given. Finally, the trend of winding loss with current frequency, winding thickness and inter layer spacing is obtained through calculation. The winding loss initially decreases as the thickness of the winding increases, but when it reaches a certain level, this reduction becomes insignificant.

Structural optimisation of cage induction motors using finite element analysis

NASA Astrophysics Data System (ADS)

Palko, S.

The current trend in motor design is to have highly efficient, low noise, low cost, and modular motors with a high power factor. High torque motors are useful in applications like servo motors, lifts, cranes, and rolling mills. This report contains a detailed review of different optimization methods applicable in various design problems. Special attention is given to the performance of different methods, when they are used with finite element analysis (FEA) as an objective function, and accuracy problems arising from the numerical simulations. Also an effective method for designing high starting torque and high efficiency motors is presented. The method described in this work utilizes FEA combined with algorithms for the optimization of the slot geometry. The optimization algorithm modifies the position of the nodal points in the element mesh. The number of independent variables ranges from 14 to 140 in this work.

Reducing fischer-tropsch catalyst attrition losses in high agitation reaction systems

DOEpatents

Singleton, Alan H.; Oukaci, Rachid; Goodwin, James G.

2001-01-01

A method for reducing catalyst attrition losses in hydrocarbon synthesis processes conducted in high agitation reaction systems; a method of producing an attrition-resistant catalyst; a catalyst produced by such method; a method of producing an attrition-resistant catalyst support; and a catalyst support produced by such method. The inventive method of reducing catalyst attrition losses comprises the step of reacting a synthesis gas in a high agitation reaction system in the presence of a catalyst. In one aspect, the catalyst preferably comprises a .gamma.-alumina support including an amount of titanium effective for increasing the attrition resistance of the catalyst. In another aspect, the catalyst preferably comprises a .gamma.-alumina support which has been treated, after calcination, with an acidic, aqueous solution. The acidic aqueous solution preferably has a pH of not more than about 5. In another aspect, the catalyst preferably comprises cobalt on a .gamma.-alumina support wherein the cobalt has been applied to the .gamma.-alumina support by totally aqueous, incipient wetness-type impregnation. In another aspect, the catalyst preferably comprises cobalt on a .gamma.-alumina support with an amount of a lanthana promoter effective for increasing the attrition resistance of the catalyst. In another aspect, the catalyst preferably comprises a .gamma.-alumina support produced from boehmite having a crystallite size, in the 021 plane, in the range of from about 30 to about 55 .ANG.ngstrons. In another aspect, the inventive method of producing an attrition-resistant catalyst comprises the step of treating a .gamma.-alumina support, after calcination of and before adding catalytic material to the support, with an acidic solution effective for increasing the attrition resistance of the catalyst. In another aspect, the inventive method of producing an attrition-resistant catalyst support comprises the step of treating calcined .gamma.-alumina with an acidic, aqueous solution effective for increasing the attrition resistance of the .gamma.-alumina.

Biological Matrix Effects in Quantitative Tandem Mass Spectrometry-Based Analytical Methods: Advancing Biomonitoring

PubMed Central

Panuwet, Parinya; Hunter, Ronald E.; D’Souza, Priya E.; Chen, Xianyu; Radford, Samantha A.; Cohen, Jordan R.; Marder, M. Elizabeth; Kartavenka, Kostya; Ryan, P. Barry; Barr, Dana Boyd

2015-01-01

The ability to quantify levels of target analytes in biological samples accurately and precisely, in biomonitoring, involves the use of highly sensitive and selective instrumentation such as tandem mass spectrometers and a thorough understanding of highly variable matrix effects. Typically, matrix effects are caused by co-eluting matrix components that alter the ionization of target analytes as well as the chromatographic response of target analytes, leading to reduced or increased sensitivity of the analysis. Thus, before the desired accuracy and precision standards of laboratory data are achieved, these effects must be characterized and controlled. Here we present our review and observations of matrix effects encountered during the validation and implementation of tandem mass spectrometry-based analytical methods. We also provide systematic, comprehensive laboratory strategies needed to control challenges posed by matrix effects in order to ensure delivery of the most accurate data for biomonitoring studies assessing exposure to environmental toxicants. PMID:25562585

Use of Reversible Contraceptive Methods Among U.S. Women with Physical or Sensory Disabilities.

PubMed

Wu, Justine P; McKee, Kimberly S; McKee, Michael M; Meade, Michelle A; Plegue, Melissa A; Sen, Ananda

2017-09-01

Women with disabilities experience a higher rate of adverse pregnancy outcomes than women without disabilities. Preventing or delaying pregnancy when that is the best choice for a woman is a critical strategy to reducing pregnancy-related disparities, yet little is known about current contraceptive use among women with disabilities. A cohort of 545 reproductive-age women with physical disabilities (i.e., difficulty walking, climbing, dressing or bathing) or sensory disabilities (i.e., difficulty with vision or hearing) was identified from among participants in the 2011-2013 National Survey of Family Growth. Those at risk for unplanned pregnancy were categorized by whether they were using highly effective reversible contraceptive methods (IUD, implant), moderately effective ones (pill, patch, ring, injectable), less effective ones (condoms, withdrawal, spermicides, diaphragm, natural family planning) or no method. Multinomial regression was conducted to examine the association between disability and type of contraceptive used. Some 39% of women with disabilities were at risk of unplanned pregnancy, and 27% of those at risk were not using contraceptives. The presence of disability was associated with decreased odds of using highly effective methods or moderately effective methods, rather than less effective ones (odds ratio, 0.6 for each), but had no association with using no method. There is a significant need to reduce contraceptive disparities related to physical or sensory disabilities. Future research should explore the extent to which contraceptive use differs by type and severity of disability, as well as identify contextual factors that contribute to any identified differences. Copyright © 2017 by the Guttmacher Institute.

Effect of contrast enhancement prior to iteration procedure on image correction for soft x-ray projection microscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jamsranjav, Erdenetogtokh, E-mail: ja.erdenetogtokh@gmail.com; Shiina, Tatsuo, E-mail: shiina@faculity.chiba-u.jp; Kuge, Kenichi

2016-01-28

Soft X-ray microscopy is well recognized as a powerful tool of high-resolution imaging for hydrated biological specimens. Projection type of it has characteristics of easy zooming function, simple optical layout and so on. However the image is blurred by the diffraction of X-rays, leading the spatial resolution to be worse. In this study, the blurred images have been corrected by an iteration procedure, i.e., Fresnel and inverse Fresnel transformations repeated. This method was confirmed by earlier studies to be effective. Nevertheless it was not enough to some images showing too low contrast, especially at high magnification. In the present study,more » we tried a contrast enhancement method to make the diffraction fringes clearer prior to the iteration procedure. The method was effective to improve the images which were not successful by iteration procedure only.« less

Synthesis and characterization of transparent conductive zinc oxide thin films by sol-gel spin coating method

NASA Astrophysics Data System (ADS)

Winarski, David

Zinc oxide has been given much attention recently as it is promising for various semiconductor device applications. ZnO has a direct band gap of 3.3 eV, high exciton binding energy of 60 meV and can exist in various bulk powder and thin film forms for different applications. ZnO is naturally n-type with various structural defects, which sparks further investigation into the material properties. Although there are many potential applications for this ZnO, an overall lack of understand and control of intrinsic defects has proven difficult to obtain consistent, repeatable results. This work studies both synthesis and characterization of zinc oxide in an effort to produce high quality transparent conductive oxides. The sol-gel spin coating method was used to obtain highly transparent ZnO thin films with high UV absorbance. This research develops a new more consistent method for synthesis of these thin films, providing insight for maintaining quality control for each step in the procedure. A sol-gel spin coating technique is optimized, yielding highly transparent polycrystalline ZnO thin films with tunable electrical properties. Annealing treatment in hydrogen and zinc atmospheres is researched in an effort to increase electrical conductivity and better understand intrinsic properties of the material. These treatment have shown significant effects on the properties of ZnO. Characterization of doped and undoped ZnO synthesized by the sol-gel spin coating method was carried out using scanning electron microscopy, UV-Visible range absorbance, X-ray diffraction, and the Hall Effect. Treatment in hydrogen shows an overall decrease in the number of crystal phases and visible absorbance while zinc seems to have the opposite effect. The Hall Effect has shown that both annealing environments increase the n-type conductivity, yielding a ZnO thin film with a carrier concentration as high as 3.001 x 1021 cm-3.

The effects of nutrient solution sterilization on the growth and yield of hydroponically grown lettuce

NASA Technical Reports Server (NTRS)

Schwartzkopf, S. H.; Dudzinski, D.; Minners, R. S.

1987-01-01

Two methods of removing bacteria from hydroponic nutrient solution [ultraviolet (UV) radiation and submicronic filter] were evaluated for efficiency and for their effects on lettuce (Lactuca sativa L.) production. Both methods were effective in removing bacteria; but, at high intensity, the ultraviolet sterilizer significantly inhibited the production of plants grown in the treated solution. Bacterial removal by lower intensity UV or a submicronic filter seemed to promote plant growth slightly, but showed no consistent, statistically significant effect.

Effect of sample stratification on dairy GWAS results

PubMed Central

2012-01-01

Background Artificial insemination and genetic selection are major factors contributing to population stratification in dairy cattle. In this study, we analyzed the effect of sample stratification and the effect of stratification correction on results of a dairy genome-wide association study (GWAS). Three methods for stratification correction were used: the efficient mixed-model association expedited (EMMAX) method accounting for correlation among all individuals, a generalized least squares (GLS) method based on half-sib intraclass correlation, and a principal component analysis (PCA) approach. Results Historical pedigree data revealed that the 1,654 contemporary cows in the GWAS were all related when traced through approximately 10–15 generations of ancestors. Genome and phenotype stratifications had a striking overlap with the half-sib structure. A large elite half-sib family of cows contributed to the detection of favorable alleles that had low frequencies in the general population and high frequencies in the elite cows and contributed to the detection of X chromosome effects. All three methods for stratification correction reduced the number of significant effects. EMMAX method had the most severe reduction in the number of significant effects, and the PCA method using 20 principal components and GLS had similar significance levels. Removal of the elite cows from the analysis without using stratification correction removed many effects that were also removed by the three methods for stratification correction, indicating that stratification correction could have removed some true effects due to the elite cows. SNP effects with good consensus between different methods and effect size distributions from USDA’s Holstein genomic evaluation included the DGAT1-NIBP region of BTA14 for production traits, a SNP 45kb upstream from PIGY on BTA6 and two SNPs in NIBP on BTA14 for protein percentage. However, most of these consensus effects had similar frequencies in the elite and average cows. Conclusions Genetic selection and extensive use of artificial insemination contributed to overlapped genome, pedigree and phenotype stratifications. The presence of an elite cluster of cows was related to the detection of rare favorable alleles that had high frequencies in the elite cluster and low frequencies in the remaining cows. Methods for stratification correction could have removed some true effects associated with genetic selection. PMID:23039970

New Cogging Torque Reduction Methods for Permanent Magnet Machine

NASA Astrophysics Data System (ADS)

Bahrim, F. S.; Sulaiman, E.; Kumar, R.; Jusoh, L. I.

2017-08-01

Permanent magnet type motors (PMs) especially permanent magnet synchronous motor (PMSM) are expanding its limbs in industrial application system and widely used in various applications. The key features of this machine include high power and torque density, extending speed range, high efficiency, better dynamic performance and good flux-weakening capability. Nevertheless, high in cogging torque, which may cause noise and vibration, is one of the threat of the machine performance. Therefore, with the aid of 3-D finite element analysis (FEA) and simulation using JMAG Designer, this paper proposed new method for cogging torque reduction. Based on the simulation, methods of combining the skewing with radial pole pairing method and skewing with axial pole pairing method reduces the cogging torque effect up to 71.86% and 65.69% simultaneously.

A study of prediction methods for the high angle-of-attack aerodynamics of straight wings and fighter aircraft

NASA Technical Reports Server (NTRS)

Mcmillan, O. J.; Mendenhall, M. R.; Perkins, S. C., Jr.

1984-01-01

Work is described dealing with two areas which are dominated by the nonlinear effects of vortex flows. The first area concerns the stall/spin characteristics of a general aviation wing with a modified leading edge. The second area concerns the high-angle-of-attack characteristics of high performance military aircraft. For each area, the governing phenomena are described as identified with the aid of existing experimental data. Existing analytical methods are reviewed, and the most promising method for each area used to perform some preliminary calculations. Based on these results, the strengths and weaknesses of the methods are defined, and research programs recommended to improve the methods as a result of better understanding of the flow mechanisms involved.

The Effect of High Pressure Techniques on the Stability of Anthocyanins in Fruit and Vegetables

PubMed Central

Marszałek, Krystian; Woźniak, Łukasz; Kruszewski, Bartosz; Skąpska, Sylwia

2017-01-01

Anthocyanins are a group of phenolic compounds responsible for red, blue and violet colouration of many fruits, vegetables and flowers. The high content of these pigments is important as it influences directly their health promoting properties as well as the sensory quality of the product; however they are prone to degradation by, inter alia, elevated temperature and tissue enzymes. The traditional thermal methods of food preservation cause significant losses of these pigments. Thus, novel non-thermal techniques such as high pressure processing, high pressure carbon dioxide and high pressure homogenization are under consideration. In this review, the authors attempted to summarize the current knowledge of the impact of high pressure techniques on the stability of anthocyanins during processing and storage of fruit and vegetable products. Furthermore, the effect of the activity of enzymes involved in the degradation of these compounds has been described. The conclusions including comparisons of pressure-based methods with high temperature preservation techniques were presented. PMID:28134807

The Effect of High Pressure Techniques on the Stability of Anthocyanins in Fruit and Vegetables.

PubMed

Marszałek, Krystian; Woźniak, Łukasz; Kruszewski, Bartosz; Skąpska, Sylwia

2017-01-27

Anthocyanins are a group of phenolic compounds responsible for red, blue and violet colouration of many fruits, vegetables and flowers. The high content of these pigments is important as it influences directly their health promoting properties as well as the sensory quality of the product; however they are prone to degradation by, inter alia, elevated temperature and tissue enzymes. The traditional thermal methods of food preservation cause significant losses of these pigments. Thus, novel non-thermal techniques such as high pressure processing, high pressure carbon dioxide and high pressure homogenization are under consideration. In this review, the authors attempted to summarize the current knowledge of the impact of high pressure techniques on the stability of anthocyanins during processing and storage of fruit and vegetable products. Furthermore, the effect of the activity of enzymes involved in the degradation of these compounds has been described. The conclusions including comparisons of pressure-based methods with high temperature preservation techniques were presented.

Accurate prediction of protein-protein interactions by integrating potential evolutionary information embedded in PSSM profile and discriminative vector machine classifier.

PubMed

Li, Zheng-Wei; You, Zhu-Hong; Chen, Xing; Li, Li-Ping; Huang, De-Shuang; Yan, Gui-Ying; Nie, Ru; Huang, Yu-An

2017-04-04

Identification of protein-protein interactions (PPIs) is of critical importance for deciphering the underlying mechanisms of almost all biological processes of cell and providing great insight into the study of human disease. Although much effort has been devoted to identifying PPIs from various organisms, existing high-throughput biological techniques are time-consuming, expensive, and have high false positive and negative results. Thus it is highly urgent to develop in silico methods to predict PPIs efficiently and accurately in this post genomic era. In this article, we report a novel computational model combining our newly developed discriminative vector machine classifier (DVM) and an improved Weber local descriptor (IWLD) for the prediction of PPIs. Two components, differential excitation and orientation, are exploited to build evolutionary features for each protein sequence. The main characteristics of the proposed method lies in introducing an effective feature descriptor IWLD which can capture highly discriminative evolutionary information from position-specific scoring matrixes (PSSM) of protein data, and employing the powerful and robust DVM classifier. When applying the proposed method to Yeast and H. pylori data sets, we obtained excellent prediction accuracies as high as 96.52% and 91.80%, respectively, which are significantly better than the previous methods. Extensive experiments were then performed for predicting cross-species PPIs and the predictive results were also pretty promising. To further validate the performance of the proposed method, we compared it with the state-of-the-art support vector machine (SVM) classifier on Human data set. The experimental results obtained indicate that our method is highly effective for PPIs prediction and can be taken as a supplementary tool for future proteomics research.

Rapid detection of Ganoderma-infected oil palms by microwave ergosterol extraction with HPLC and TLC.

PubMed

Muniroh, M S; Sariah, M; Zainal Abidin, M A; Lima, N; Paterson, R R M

2014-05-01

Detection of basal stem rot (BSR) by Ganoderma of oil palms was based on foliar symptoms and production of basidiomata. Enzyme-Linked Immunosorbent Assays-Polyclonal Antibody (ELISA-PAB) and PCR have been proposed as early detection methods for the disease. These techniques are complex, time consuming and have accuracy limitations. An ergosterol method was developed which correlated well with the degree of infection in oil palms, including samples growing in plantations. However, the method was capable of being optimised. This current study was designed to develop a simpler, more rapid and efficient ergosterol method with utility in the field that involved the use of microwave extraction. The optimised procedure involved extracting a small amount of Ganoderma, or Ganoderma-infected oil palm suspended in low volumes of solvent followed by irradiation in a conventional microwave oven at 70°C and medium high power for 30s, resulting in simultaneous extraction and saponification. Ergosterol was detected by thin layer chromatography (TLC) and quantified using high performance liquid chromatography with diode array detection. The TLC method was novel and provided a simple, inexpensive method with utility in the field. The new method was particularly effective at extracting high yields of ergosterol from infected oil palm and enables rapid analysis of field samples on site, allowing infected oil palms to be treated or culled very rapidly. Some limitations of the method are discussed herein. The procedures lend themselves to controlling the disease more effectively and allowing more effective use of land currently employed to grow oil palms, thereby reducing pressure to develop new plantations. Copyright © 2014 Elsevier B.V. All rights reserved.

Deformation effect simulation and optimization for double front axle steering mechanism

NASA Astrophysics Data System (ADS)

Wu, Jungang; Zhang, Siqin; Yang, Qinglong

2013-03-01

This paper research on tire wear problem of heavy vehicles with Double Front Axle Steering Mechanism from the flexible effect of Steering Mechanism, and proposes a structural optimization method which use both traditional static structural theory and dynamic structure theory - Equivalent Static Load (ESL) method to optimize key parts. The good simulated and test results show this method has high engineering practice and reference value for tire wear problem of Double Front Axle Steering Mechanism design.

Characterization of non-conductive materials using field emission scanning electron microscopy

NASA Astrophysics Data System (ADS)

Cao, Cong; Gao, Ran; Shang, Huayan; Peng, Tingting

2016-01-01

With the development of science and technology, field emission scanning electron microscope (FESEM) plays an important role in nano-material measurements because of its advantages of high magnification, high resolution and easy operation. A high-quality secondary electron image is a significant prerequisite for accurate and precise length measurements. In order to obtain high-quality secondary electron images, the conventional treatment method for non-conductive materials is coating conductive films with gold, carbon or platinum to reduce charging effects, but this method will cover real micro structures of materials, change the sample composition properties and meanwhile introduce a relatively big error to nano-scale microstructure measurements. This paper discusses how to reduce or eliminate the impact of charging effects on image quality to the greatest extent by changing working conditions, such as voltage, stage bias, scanning mode and so on without treatment of coating, to obtain real and high-quality microstructure information of materials.

Design of matching layers for high-frequency ultrasonic transducers

PubMed Central

Fei, Chunlong; Ma, Jianguo; Chiu, Chi Tat; Williams, Jay A.; Fong, Wayne; Chen, Zeyu; Zhu, BenPeng; Xiong, Rui; Shi, Jing; Hsiai, Tzung K.; Shung, K. Kirk; Zhou, Qifa

2015-01-01

Matching the acoustic impedance of high-frequency (≥100 MHz) ultrasound transducers to an aqueous loading medium remains a challenge for fabricating high-frequency transducers. The traditional matching layer design has been problematic to establish high matching performance given requirements on both specific acoustic impedance and precise thickness. Based on both mass-spring scheme and microwave matching network analysis, we interfaced metal-polymer layers for the matching effects. Both methods hold promises for guiding the metal-polymer matching layer design. A 100 MHz LiNbO3 transducer was fabricated to validate the performance of the both matching layer designs. In the pulse-echo experiment, the transducer echo amplitude increased by 84.4% and its −6dB bandwidth increased from 30.2% to 58.3% comparing to the non-matched condition, demonstrating that the matching layer design method is effective for developing high-frequency ultrasonic transducers. PMID:26445518

Effective screen of CRISPR/Cas9-induced mutants in rice by single-strand conformation polymorphism.

PubMed

Zheng, Xuelian; Yang, Shixin; Zhang, Dengwei; Zhong, Zhaohui; Tang, Xu; Deng, Kejun; Zhou, Jianping; Qi, Yiping; Zhang, Yong

2016-07-01

A method based on DNA single-strand conformation polymorphism is demonstrated for effective genotyping of CRISPR/Cas9-induced mutants in rice. Clustered regularly interspaced short palindromic repeats (CRISPR)/CRISPR-associated 9 (Cas9) has been widely adopted for genome editing in many organisms. A large proportion of mutations generated by CRISPR/Cas9 are very small insertions and deletions (indels), presumably because Cas9 generates blunt-ended double-strand breaks which are subsequently repaired without extensive end-processing. CRISPR/Cas9 is highly effective for targeted mutagenesis in the important crop, rice. For example, homozygous mutant seedlings are commonly recovered from CRISPR/Cas9-treated calli. However, many current mutation detection methods are not very suitable for screening homozygous mutants that typically carry small indels. In this study, we tested a mutation detection method based on single-strand conformational polymorphism (SSCP). We found it can effectively detect small indels in pilot experiments. By applying the SSCP method for CRISRP-Cas9-mediated targeted mutagenesis in rice, we successfully identified multiple mutants of OsROC5 and OsDEP1. In conclusion, the SSCP analysis will be a useful genotyping method for rapid identification of CRISPR/Cas9-induced mutants, including the most desirable homozygous mutants. The method also has high potential for similar applications in other plant species.

Modelling cost-effectiveness of different vasectomy methods in India, Kenya, and Mexico.

PubMed

Seamans, Yancy; Harner-Jay, Claudia M

2007-07-13

Vasectomy is generally considered a safe and effective method of permanent contraception. The historical effectiveness of vasectomy has been questioned by recent research results indicating that the most commonly used method of vasectomy--simple ligation and excision (L and E)--appears to have a relatively high failure rate, with reported pregnancy rates as high as 4%. Updated methods such as fascial interposition (FI) and thermal cautery can lower the rate of failure but may require additional financial investments and may not be appropriate for low-resource clinics. In order to better compare the cost-effectiveness of these different vasectomy methods, we modelled the costs of different vasectomy methods using cost data collected in India, Kenya, and Mexico and effectiveness data from the latest published research. The costs associated with providing vasectomies were determined in each country through interviews with clinic staff. Costs collected were economic, direct, programme costs of fixed vasectomy services but did not include large capital expenses or general recurrent costs for the health care facility. Estimates of the time required to provide service were gained through interviews and training costs were based on the total costs of vasectomy training programmes in each country. Effectiveness data were obtained from recent published studies and comparative cost-effectiveness was determined using cost per couple years of protection (CYP). In each country, the labour to provide the vasectomy and follow-up services accounts for the greatest portion of the overall cost. Because each country almost exclusively used one vasectomy method at all of the clinics included in the study, we modelled costs based on the additional material, labour, and training costs required in each country. Using a model of a robust vasectomy program, more effective methods such as FI and thermal cautery reduce the cost per CYP of a vasectomy by $0.08-$0.55. Based on the results presented, more effective methods of vasectomy--including FI, thermal cautery, and thermal cautery combined with FI--are more cost-effective than L and E alone. Analysis shows that for a programme in which a minimum of 20 clients undergo vasectomies per month, the cost per CYP is reduced in all three countries by updated vasectomy methods.

Brief Report: Dapivirine Vaginal Ring Use Does Not Diminish the Effectiveness of Hormonal Contraception.

PubMed

Balkus, Jennifer E; Palanee-Phillips, Thesla; Reddy, Krishnaveni; Siva, Samantha; Harkoo, Ishana; Nakabiito, Clemensia; Kintu, Kenneth; Nair, Gonasangrie; Chappell, Catherine; Kiweewa, Flavia Matovu; Kabwigu, Samuel; Naidoo, Logashvari; Jeenarain, Nitesha; Marzinke, Mark; Soto-Torres, Lydia; Brown, Elizabeth R; Baeten, Jared M

2017-10-01

To evaluate the potential for a clinically relevant drug-drug interaction with concomitant use of a dapivirine vaginal ring, a novel antiretroviral-based HIV-1 prevention strategy, and hormonal contraception by examining contraceptive efficacies with and without dapivirine ring use. A secondary analysis of women participating in MTN-020/ASPIRE, a randomized, double-blind, placebo-controlled trial of the dapivirine vaginal ring for HIV-1 prevention. Use of a highly effective method of contraception was an eligibility criterion for study participation. Urine pregnancy tests were performed monthly. Pregnancy incidence by arm was calculated separately for each hormonal contraceptive method and compared using an Andersen-Gill proportional hazards model stratified by site and censored at HIV-1 infection. Of 2629 women enrolled, 2310 women returned for follow-up and reported using a hormonal contraceptive method at any point during study participation (1139 in the dapivirine arm and 1171 in the placebo arm). Pregnancy incidence in the dapivirine arm versus placebo among women using injectable depot medroxyprogesterone acetate was 0.43% vs. 0.54%, among women using injectable norethisterone enanthate was 1.15% vs. 0%, among women using hormonal implants was 0.22% vs. 0.69%, and among women using oral contraceptive pills was 32.26% vs. 28.01%. Pregnancy incidence did not differ by study arm for any of the hormonal contraceptive methods. Use of the dapivirine ring does not reduce the effectiveness of hormonal contraceptives for pregnancy prevention. Oral contraceptive pill use was associated with high pregnancy incidence, potentially because of poor pill adherence. Injectable and implantable methods were highly effective in preventing pregnancy.

Estimation of genetic effects in the presence of multicollinearity in multibreed beef cattle evaluation.

PubMed

Roso, V M; Schenkel, F S; Miller, S P; Schaeffer, L R

2005-08-01

Breed additive, dominance, and epistatic loss effects are of concern in the genetic evaluation of a multibreed population. Multiple regression equations used for fitting these effects may show a high degree of multicollinearity among predictor variables. Typically, when strong linear relationships exist, the regression coefficients have large SE and are sensitive to changes in the data file and to the addition or deletion of variables in the model. Generalized ridge regression methods were applied to obtain stable estimates of direct and maternal breed additive, dominance, and epistatic loss effects in the presence of multicollinearity among predictor variables. Preweaning weight gains of beef calves in Ontario, Canada, from 1986 to 1999 were analyzed. The genetic model included fixed direct and maternal breed additive, dominance, and epistatic loss effects, fixed environmental effects of age of the calf, contemporary group, and age of the dam x sex of the calf, random additive direct and maternal genetic effects, and random maternal permanent environment effect. The degree and the nature of the multicollinearity were identified and ridge regression methods were used as an alternative to ordinary least squares (LS). Ridge parameters were obtained using two different objective methods: 1) generalized ridge estimator of Hoerl and Kennard (R1); and 2) bootstrap in combination with cross-validation (R2). Both ridge regression methods outperformed the LS estimator with respect to mean squared error of predictions (MSEP) and variance inflation factors (VIF) computed over 100 bootstrap samples. The MSEP of R1 and R2 were similar, and they were 3% less than the MSEP of LS. The average VIF of LS, R1, and R2 were equal to 26.81, 6.10, and 4.18, respectively. Ridge regression methods were particularly effective in decreasing the multicollinearity involving predictor variables of breed additive effects. Because of a high degree of confounding between estimates of maternal dominance and direct epistatic loss effects, it was not possible to compare the relative importance of these effects with a high level of confidence. The inclusion of epistatic loss effects in the additive-dominance model did not cause noticeable reranking of sires, dams, and calves based on across-breed EBV. More precise estimates of breed effects as a result of this study may result in more stable across-breed estimated breeding values over the years.

Corpus-based Statistical Screening for Phrase Identification

PubMed Central

Kim, Won; Wilbur, W. John

2000-01-01

Purpose: The authors study the extraction of useful phrases from a natural language database by statistical methods. The aim is to leverage human effort by providing preprocessed phrase lists with a high percentage of useful material. Method: The approach is to develop six different scoring methods that are based on different aspects of phrase occurrence. The emphasis here is not on lexical information or syntactic structure but rather on the statistical properties of word pairs and triples that can be obtained from a large database. Measurements: The Unified Medical Language System (UMLS) incorporates a large list of humanly acceptable phrases in the medical field as a part of its structure. The authors use this list of phrases as a gold standard for validating their methods. A good method is one that ranks the UMLS phrases high among all phrases studied. Measurements are 11-point average precision values and precision-recall curves based on the rankings. Result: The authors find of six different scoring methods that each proves effective in identifying UMLS quality phrases in a large subset of MEDLINE. These methods are applicable both to word pairs and word triples. All six methods are optimally combined to produce composite scoring methods that are more effective than any single method. The quality of the composite methods appears sufficient to support the automatic placement of hyperlinks in text at the site of highly ranked phrases. Conclusion: Statistical scoring methods provide a promising approach to the extraction of useful phrases from a natural language database for the purpose of indexing or providing hyperlinks in text. PMID:10984469

Hypothesis test of mediation effect in causal mediation model with high-dimensional continuous mediators.

PubMed

Huang, Yen-Tsung; Pan, Wen-Chi

2016-06-01

Causal mediation modeling has become a popular approach for studying the effect of an exposure on an outcome through a mediator. However, current methods are not applicable to the setting with a large number of mediators. We propose a testing procedure for mediation effects of high-dimensional continuous mediators. We characterize the marginal mediation effect, the multivariate component-wise mediation effects, and the L2 norm of the component-wise effects, and develop a Monte-Carlo procedure for evaluating their statistical significance. To accommodate the setting with a large number of mediators and a small sample size, we further propose a transformation model using the spectral decomposition. Under the transformation model, mediation effects can be estimated using a series of regression models with a univariate transformed mediator, and examined by our proposed testing procedure. Extensive simulation studies are conducted to assess the performance of our methods for continuous and dichotomous outcomes. We apply the methods to analyze genomic data investigating the effect of microRNA miR-223 on a dichotomous survival status of patients with glioblastoma multiforme (GBM). We identify nine gene ontology sets with expression values that significantly mediate the effect of miR-223 on GBM survival. © 2015, The International Biometric Society.

An overview of computational simulation methods for composite structures failure and life analysis

NASA Technical Reports Server (NTRS)

Chamis, Christos C.

1993-01-01

Three parallel computational simulation methods are being developed at the LeRC Structural Mechanics Branch (SMB) for composite structures failure and life analysis: progressive fracture CODSTRAN; hierarchical methods for high-temperature composites; and probabilistic evaluation. Results to date demonstrate that these methods are effective in simulating composite structures failure/life/reliability.

Method for double-sided processing of thin film transistors

DOEpatents

Yuan, Hao-Chih; Wang, Guogong; Eriksson, Mark A.; Evans, Paul G.; Lagally, Max G.; Ma, Zhenqiang

2008-04-08

This invention provides methods for fabricating thin film electronic devices with both front- and backside processing capabilities. Using these methods, high temperature processing steps may be carried out during both frontside and backside processing. The methods are well-suited for fabricating back-gate and double-gate field effect transistors, double-sided bipolar transistors and 3D integrated circuits.

A GIHS-based spectral preservation fusion method for remote sensing images using edge restored spectral modulation

NASA Astrophysics Data System (ADS)

Zhou, Xiran; Liu, Jun; Liu, Shuguang; Cao, Lei; Zhou, Qiming; Huang, Huawen

2014-02-01

High spatial resolution and spectral fidelity are basic standards for evaluating an image fusion algorithm. Numerous fusion methods for remote sensing images have been developed. Some of these methods are based on the intensity-hue-saturation (IHS) transform and the generalized IHS (GIHS), which may cause serious spectral distortion. Spectral distortion in the GIHS is proven to result from changes in saturation during fusion. Therefore, reducing such changes can achieve high spectral fidelity. A GIHS-based spectral preservation fusion method that can theoretically reduce spectral distortion is proposed in this study. The proposed algorithm consists of two steps. The first step is spectral modulation (SM), which uses the Gaussian function to extract spatial details and conduct SM of multispectral (MS) images. This method yields a desirable visual effect without requiring histogram matching between the panchromatic image and the intensity of the MS image. The second step uses the Gaussian convolution function to restore lost edge details during SM. The proposed method is proven effective and shown to provide better results compared with other GIHS-based methods.

Ultraviolet, visible, and infrared laser delivery using laser-to-fiber coupling via a grazing-incidence-based hollow taper

NASA Astrophysics Data System (ADS)

Ilev, Ilko K.; Waynant, Ronald W.

2001-01-01

We present a novel all-optical-waveguide method for ultraviolet (UV), visible (VIS) and infrared (IR) laser delivery including a lens-free method of laser-to-fiber coupling using a simple uncoated glass hollow taper. Based on the grazing incidence effect, the hollow taper provides a way of direct launching, without any intermediate focusing elements, high power laser radiation into delivery fibers. Because of the mutual action of the nearly parallel laser excitation, the mode coupling process, and mode filtering effect, the hollow taper serves as a mode converter that transforms the highly multimode profile of the input laser emission into a high-quality Gaussian-shaped profile at the taper output. When the grazing incidence effect of the taper is applied to laser delivery, the maintenance of high reflectance coefficients in a wide spectral region allows to utilize the same uncoated hollow taper for laser radiation in the UV, VIS and IR ranges. Applying the experimental hollow-taper based delivery systems, we obtain high laser- to-taper and taper-to-fiber coupling efficiencies.

Thermal, High Pressure, and Electric Field Processing Effects on Plant Cell Membrane Integrity and Relevance to Fruit and Vegetable Quality

PubMed Central

Gonzalez, Maria E; Barrett, Diane M

2010-01-01

Advanced food processing methods that accomplish inactivation of microorganisms but minimize adverse thermal exposure are of great interest to the food industry. High pressure (HP) and pulsed electric field (PEF) processing are commercially applied to produce high quality fruit and vegetable products in the United States, Europe, and Japan. Both microbial and plant cell membranes are significantly altered following exposure to heat, HP, or PEF. Our research group sought to quantify the degree of damage to plant cell membranes that occurs as a result of exposure to heat, HP, or PEF, using the same analytical methods. In order to evaluate whether new advanced processing methods are superior to traditional thermal processing methods, it is necessary to compare them. In this review, we describe the existing state of knowledge related to effects of heat, HP, and PEF on both microbial and plant cells. The importance and relevance of compartmentalization in plant cells as it relates to fruit and vegetable quality is described and various methods for quantification of plant cell membrane integrity are discussed. These include electrolyte leakage, cell viability, and proton nuclear magnetic resonance (1H-NMR). PMID:20492210

Pile-up correction algorithm based on successive integration for high count rate medical imaging and radiation spectroscopy

NASA Astrophysics Data System (ADS)

Mohammadian-Behbahani, Mohammad-Reza; Saramad, Shahyar

2018-07-01

In high count rate radiation spectroscopy and imaging, detector output pulses tend to pile up due to high interaction rate of the particles with the detector. Pile-up effects can lead to a severe distortion of the energy and timing information. Pile-up events are conventionally prevented or rejected by both analog and digital electronics. However, for decreasing the exposure times in medical imaging applications, it is important to maintain the pulses and extract their true information by pile-up correction methods. The single-event reconstruction method is a relatively new model-based approach for recovering the pulses one-by-one using a fitting procedure, for which a fast fitting algorithm is a prerequisite. This article proposes a fast non-iterative algorithm based on successive integration which fits the bi-exponential model to experimental data. After optimizing the method, the energy spectra, energy resolution and peak-to-peak count ratios are calculated for different counting rates using the proposed algorithm as well as the rejection method for comparison. The obtained results prove the effectiveness of the proposed method as a pile-up processing scheme designed for spectroscopic and medical radiation detection applications.

Thermal, high pressure, and electric field processing effects on plant cell membrane integrity and relevance to fruit and vegetable quality.

PubMed

Gonzalez, Maria E; Barrett, Diane M

2010-09-01

Advanced food processing methods that accomplish inactivation of microorganisms but minimize adverse thermal exposure are of great interest to the food industry. High pressure (HP) and pulsed electric field (PEF) processing are commercially applied to produce high quality fruit and vegetable products in the United States, Europe, and Japan. Both microbial and plant cell membranes are significantly altered following exposure to heat, HP, or PEF. Our research group sought to quantify the degree of damage to plant cell membranes that occurs as a result of exposure to heat, HP, or PEF, using the same analytical methods. In order to evaluate whether new advanced processing methods are superior to traditional thermal processing methods, it is necessary to compare them. In this review, we describe the existing state of knowledge related to effects of heat, HP, and PEF on both microbial and plant cells. The importance and relevance of compartmentalization in plant cells as it relates to fruit and vegetable quality is described and various methods for quantification of plant cell membrane integrity are discussed. These include electrolyte leakage, cell viability, and proton nuclear magnetic resonance (¹H-NMR).

Growth and Photovoltaic Properties of High-Quality GaAs Nanowires Prepared by the Two-Source CVD Method.

PubMed

Wang, Ying; Yang, Zaixing; Wu, Xiaofeng; Han, Ning; Liu, Hanyu; Wang, Shuobo; Li, Jun; Tse, WaiMan; Yip, SenPo; Chen, Yunfa; Ho, Johnny C

2016-12-01

Growing high-quality and low-cost GaAs nanowires (NWs) as well as fabricating high-performance NW solar cells by facile means is an important development towards the cost-effective next-generation photovoltaics. In this work, highly crystalline, dense, and long GaAs NWs are successfully synthesized using a two-source method on non-crystalline SiO2 substrates by a simple solid-source chemical vapor deposition method. The high V/III ratio and precursor concentration enabled by this two-source configuration can significantly benefit the NW growth and suppress the crystal defect formation as compared with the conventional one-source system. Since less NW crystal defects would contribute fewer electrons being trapped by the surface oxides, the p-type conductivity is then greatly enhanced as revealed by the electrical characterization of fabricated NW devices. Furthermore, the individual single NW and high-density NW parallel arrays achieved by contact printing can be effectively fabricated into Schottky barrier solar cells simply by employing asymmetric Ni-Al contacts, along with an open circuit voltage of ~0.3 V. All these results indicate the technological promise of these high-quality two-source grown GaAs NWs, especially for the realization of facile Schottky solar cells utilizing the asymmetric Ni-Al contact.

Unmet demand for highly effective postpartum contraception in Texas.

PubMed

Potter, Joseph E; Hopkins, Kristine; Aiken, Abigail R A; Hubert, Celia; Stevenson, Amanda J; White, Kari; Grossman, Daniel

2014-11-01

We aimed to assess women's contraceptive preferences and use in the first 6 months after delivery. The postpartum period represents a key opportunity for women to learn about and obtain effective contraception, especially since 50% of unintended pregnancies to parous women occur within 2 years of a previous birth. We conducted a prospective cohort study of 800 postpartum women recruited from three hospitals in Austin and El Paso, TX. Women aged 18-44 who wanted to delay childbearing for at least 24 months were eligible for the study and completed interviews following delivery and at 3 and 6 months postpartum. Participants were asked about the contraceptive method they were currently using and the method they would prefer to use at 6 months after delivery. At 6 months postpartum, 13% of women were using an intrauterine device or implant, and 17% were sterilized or had a partner who had had a vasectomy. Twenty-four percent were using hormonal methods, and 45% relied on less effective methods, mainly condoms and withdrawal. Yet 44% reported that they would prefer to be using sterilization, and 34% would prefer to be using long-acting reversible contraception (LARC). This study shows a considerable preference for LARC and permanent methods at 6 months postpartum. However, there is a marked discordance between women's method preference and actual use, indicating substantial unmet demand for highly effective methods of contraception. In two Texas cities, many more women preferred long-acting and permanent contraceptive methods (LAPM) than were able to access these methods at 6 months postpartum. Women's contraceptive needs could be better met by counseling about all methods, by reducing cost barriers and by making LAPM available at more sites. Copyright © 2014 Elsevier Inc. All rights reserved.

Variable-mesh method of solving differential equations

NASA Technical Reports Server (NTRS)

Van Wyk, R.

1969-01-01

Multistep predictor-corrector method for numerical solution of ordinary differential equations retains high local accuracy and convergence properties. In addition, the method was developed in a form conducive to the generation of effective criteria for the selection of subsequent step sizes in step-by-step solution of differential equations.

Evaluation of hydrate-screening methods.

PubMed

Cui, Yong; Yao, Erica

2008-07-01

The purpose of this work is to evaluate the effectiveness and reliability of several common hydrate-screening techniques, and to provide guidelines for designing hydrate-screening programs for new drug candidates. Ten hydrate-forming compounds were selected as model compounds and six hydrate-screening approaches were applied to these compounds in an effort to generate their hydrate forms. The results prove that no screening approach is universally effective in finding hydrates for small organic compounds. Rather, a combination of different methods should be used to improve screening reliability. Among the approaches tested, the dynamic water vapor sorption/desorption isotherm (DVI) method and storage under high humidity (HH) yielded 60-70% success ratios, the lowest among all techniques studied. The risk of false negatives arises in particular for nonhygroscopic compounds. On the other hand, both slurry in water (Slurry) and temperature cycling of aqueous suspension (TCS) showed high success rates (90%) with some exceptions. The mixed solvent systems (MSS) procedure also achieved high success rates (90%), and was found to be more suitable for water-insoluble compounds. For water-soluble compounds, MSS may not be the best approach because recrystallization is difficult in solutions with high water activity. Finally, vapor diffusion (VD) yielded a reasonably high success ratio in finding hydrates (80%). However, this method suffers from experimental difficulty and unreliable results for either highly water-soluble or water-insoluble compounds. This study indicates that a reliable hydrate-screening strategy should take into consideration the solubility and hygroscopicity of the compounds studied. A combination of the Slurry or TCS method with the MSS procedure could provide a screening strategy with reasonable reliability.

Large-scale wind-tunnel investigation of a close-coupled canard-delta-wing fighter model through high angles of attack

NASA Technical Reports Server (NTRS)

Stoll, F.; Koenig, D. G.

1983-01-01

Data obtained through very high angles of attack from a large-scale, subsonic wind-tunnel test of a close-coupled canard-delta-wing fighter model are analyzed. The canard delays wing leading-edge vortex breakdown, even for angles of attack at which the canard is completely stalled. A vortex-lattice method was applied which gave good predictions of lift and pitching moment up to an angle of attack of about 20 deg, where vortex-breakdown effects on performance become significant. Pitch-control inputs generally retain full effectiveness up to the angle of attack of maximum lift, beyond which, effectiveness drops off rapidly. A high-angle-of-attack prediction method gives good estimates of lift and drag for the completely stalled aircraft. Roll asymmetry observed at zero sideslip is apparently caused by an asymmetry in the model support structure.

Propulsion integration for military aircraft

NASA Technical Reports Server (NTRS)

Henderson, William P.

1989-01-01

The transonic aerodynamic characteristics for high-performance aircraft are significantly affected by shock-induced flow interactions as well as other local flow interference effects which usually occur at transonic speeds. These adverse interactions can not only cause high drag, but can cause unusual aerodynamic loadings and/or severe stability and control problems. Many new programs are underway to develop methods for reducing the adverse effects, as well as to develop an understanding of the basic flow conditions which are the primary contributors. It is anticipated that these new programs will result in technologies which can reduce the aircraft cruise drag through improved integration as well as increased aircraft maneuverability throughh the application of thrust vectoring. This paper will identify some of the primary propulsion integration problems for high performance aircraft at transonic speeds, and demonstrate several methods for reducing or eliminating the undesirable characteristics, while enhancing configuration effectiveness.

Small-signal modeling with direct parameter extraction for impact ionization effect in high-electron-mobility transistors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guan, He; Lv, Hongliang; Guo, Hui, E-mail: hguan@stu.xidian.edu.cn

2015-11-21

Impact ionization affects the radio-frequency (RF) behavior of high-electron-mobility transistors (HEMTs), which have narrow-bandgap semiconductor channels, and this necessitates complex parameter extraction procedures for HEMT modeling. In this paper, an enhanced small-signal equivalent circuit model is developed to investigate the impact ionization, and an improved method is presented in detail for direct extraction of intrinsic parameters using two-step measurements in low-frequency and high-frequency regimes. The practicability of the enhanced model and the proposed direct parameter extraction method are verified by comparing the simulated S-parameters with published experimental data from an InAs/AlSb HEMT operating over a wide frequency range. The resultsmore » demonstrate that the enhanced model with optimal intrinsic parameter values that were obtained by the direct extraction approach can effectively characterize the effects of impact ionization on the RF performance of HEMTs.« less

Antiplane shear wave propagation in fiber-reinforced composites.

PubMed

Kim, Jin-Yeon

2003-05-01

A self-consistent method for analyzing antiplane shear wave propagation in two-dimensional inhomogeneous media is presented. For applications in the high-frequency range, the self-consistent condition for the effective medium is solved being supplemented with the theory of quasidynamic effective density. Comparisons with other theoretical calculations and experimental data for fiber-reinforced composites demonstrate the merits of using the present method.

The Effect of Language Teaching Methods on Academic Success in Turkey

ERIC Educational Resources Information Center

Ökmen, Burcu; Kilic, Abdurrahman

2016-01-01

The aim of this research is to observe the effect of language teaching methods on students' TEOG foreign language exams, the exam which is necessary to pass from secondary school to high school, administered by the Ministry of Education. The research sample consisted of 95 English teachers who taught in secondary schools in Duzce in 2013-2014, and…

Effects of Learning Style and Training Method on Computer Attitude and Performance in World Wide Web Page Design Training.

ERIC Educational Resources Information Center

Chou, Huey-Wen; Wang, Yu-Fang

1999-01-01

Compares the effects of two training methods on computer attitude and performance in a World Wide Web page design program in a field experiment with high school students in Taiwan. Discusses individual differences, Kolb's Experiential Learning Theory and Learning Style Inventory, Computer Attitude Scale, and results of statistical analyses.…

A Review of Analytical Methods for p-Coumaric Acid in Plant-Based Products, Beverages, and Biological Matrices.

PubMed

Ferreira, Paula Scanavez; Victorelli, Francesca Damiani; Fonseca-Santos, Bruno; Chorilli, Marlus

2018-05-14

p-Coumaric acid (p-CA), also known as 4-hydroxycinnamic acid, is a phenolic acid, which has been widely studied due to its beneficial effects against several diseases and its wide distribution in the plant kingdom. This phenolic compound can be found in the free form or conjugated with other molecules; therefore, its bioavailability and the pathways via which it is metabolized change according to its chemical structure. p-CA has potential pharmacological effects because it has high free radical scavenging, anti-inflammatory, antineoplastic, and antimicrobial activities, among other biological properties. It is therefore essential to choose the most appropriate and effective analytical method for qualitative and quantitative determination of p-CA in different matrices, such as plasma, urine, plant extracts, and drug delivery systems. The most-reported analytical method for this purpose is high-performance liquid chromatography, which is mostly coupled with some type of detectors, such as UV/Vis detector. However, other analytical techniques are also used to evaluate this compound. This review presents a summary of p-CA in terms of its chemical and pharmacokinetic properties, pharmacological effects, drug delivery systems, and the analytical methods described in the literature that are suitable for its quantification.

Analysis of fuel using the Direct LSC method determination of bio-originated fuel in the presence of quenching.

PubMed

Doll, Charles G; Wright, Cherylyn W; Morley, Shannon M; Wright, Bob W

2017-04-01

A modified version of the Direct LSC method to correct for quenching effect was investigated for the determination of bio-originated fuel content in fuel samples produced from multiple biological starting materials. The modified method was found to be accurate in determining the percent bio-originated fuel to within 5% of the actual value for samples with quenching effects ≤43%. Analysis of highly quenched samples was possible when diluted with the exception of one sample with a 100% quenching effect. Copyright © 2017. Published by Elsevier Ltd.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schaeffel, J.A.; Mullinix, B.R.; Ranson, W.F.

An experimental technique to simulate and evaluate the effects of high concentrations of x-rays resulting from a nuclear detonation on missile structures is presented. Data from 34 tests are included to demonstrate the technique. The effects of variations in the foil thickness, capacitor voltage, and plate thickness on the total impulse and maximum strain in the structure were determined. The experimental technique utilizes a high energy capacitor discharge unit to explode an aluminum foil on the surface of the structure. The structural response is evaluated by optical methods using the grid slope deflection method. The fringe patterns were recorded usingmore » a high-speed framing camera. The data were digitized using an optical comparator with an x-y table. The analysis was performed on a CDC 6600 computer.« less

COPE Method Implementation Program to Reduce Communication Apprehension Level in Full Day Yunior High School Students

NASA Astrophysics Data System (ADS)

Prasetyo, A. R.

2017-02-01

This study was aimed to explore the effect of COPE method to reduce communication apprehension level of students in Early Adolescence who become Full Day Junior High School students. Full Day Junior High School students, especially in Surabaya coastal area, have more demands to develop the communication aspects such as group discussions and presentations and extracurricular activities. Higher demands to develop such aspects of communication may cause them to experience communication apprehension. The subject was Full Day School students totaling 31 students. The design of the research was experimental design. The experimental method used was a non-randomized pretest posttest control group design and purposive sampling was also used. COPE method is a process that consists of four main stages where people are trying to deal with and control of stressful situations as a result of the problem being faced by conducting cognitive and behavioral changes. Four main stages COPE method is Calming the nervous system, Originating an imaginative plan, Persisting in the face of obstacles and failure, and Evaluating and adjusting the plan. Results of quantitative analysis based on U-Mann Whitney Test shows significant effect on the COPE Method to decrease anxiety levels of communication (0.000 <0.005).

Axial resonance of periodic patterns by using a Fresnel biprism.

PubMed

Doblas, Ana; Saavedra, Genaro; Martinez-Corral, Manuel; Barreiro, Juan C; Sanchez-Ortiga, Emilio; Llavador, Anabel

2013-01-01

This paper proposes a method for the generation of high-contrast localized sinusoidal fringes with spatially noncoherent illumination and relatively high light throughput. The method, somehow similar to the classical Lau effect, is based on the use of a Fresnel biprism. It has some advantages over previous methods for the noncoherent production of interference fringes. One is the flexibility of the method, which allows the control of the fringe period by means of a simple axial shift of the biprism. Second is the rapid axial fall-off in visibility around the high-contrast fringe planes. And third is the possibility of creating fringes with increasing or with constant period as the light beam propagates. Experimental verifications of the theoretical statements are also provided.

Proximity Effect Correction by Pattern Modified Stencil Mask in Large-Field Projection Electron-Beam Lithography

NASA Astrophysics Data System (ADS)

Kobinata, Hideo; Yamashita, Hiroshi; Nomura, Eiichi; Nakajima, Ken; Kuroki, Yukinori

1998-12-01

A new method for proximity effect correction, suitable for large-field electron-beam (EB) projection lithography with high accelerating voltage, such as SCALPEL and PREVAIL in the case where a stencil mask is used, is discussed. In this lithography, a large-field is exposed by the same dose, and thus, the dose modification method, which is used in the variable-shaped beam and the cell projection methods, cannot be used in this case. In this study, we report on development of a new proximity effect correction method which uses a pattern modified stencil mask suitable for high accelerating voltage and large-field EB projection lithography. In order to obtain the mask bias value, we have investigated linewidth reduction, due to the proximity effect, in the peripheral memory cell area, and found that it could be expressed by a simple function and all the correction parameters were easily determined from only the mask pattern data. The proximity effect for the peripheral array pattern could also be corrected by considering the pattern density. Calculated linewidth deviation was 3% or less for a 0.07-µm-L/S memory cell pattern and 5% or less for a 0.14-µm-line and 0.42-µm-space peripheral array pattern, simultaneously.

The effects of guided inquiry instruction on student achievement in high school biology

NASA Astrophysics Data System (ADS)

Vass, Laszlo

The purpose of this quantitative, quasi-experimental study was to measure the effect of a student-centered instructional method called guided inquiry on the achievement of students in a unit of study in high school biology. The study used a non-random sample of 109 students, the control group of 55 students enrolled in high school one, received teacher centered instruction while the experimental group of 54 students enrolled at high school two received student-centered, guided inquiry instruction. The pretest-posttest design of the study analyzed scores using an independent t-test, a dependent t-test (p = <.001), an ANCOVA (p = .007), mixed method ANOVA (p = .024) and hierarchical linear regression (p = <.001). The experimental group that received guided inquiry instruction had statistically significantly higher achievement than the control group.

Implementation of an effective hybrid GA for large-scale traveling salesman problems.

PubMed

Nguyen, Hung Dinh; Yoshihara, Ikuo; Yamamori, Kunihito; Yasunaga, Moritoshi

2007-02-01

This correspondence describes a hybrid genetic algorithm (GA) to find high-quality solutions for the traveling salesman problem (TSP). The proposed method is based on a parallel implementation of a multipopulation steady-state GA involving local search heuristics. It uses a variant of the maximal preservative crossover and the double-bridge move mutation. An effective implementation of the Lin-Kernighan heuristic (LK) is incorporated into the method to compensate for the GA's lack of local search ability. The method is validated by comparing it with the LK-Helsgaun method (LKH), which is one of the most effective methods for the TSP. Experimental results with benchmarks having up to 316228 cities show that the proposed method works more effectively and efficiently than LKH when solving large-scale problems. Finally, the method is used together with the implementation of the iterated LK to find a new best tour (as of June 2, 2003) for a 1904711-city TSP challenge.

Present and future contraception: does discovery of targets lead to new contraceptives?

PubMed

Jensen, Jeffrey T

2015-01-01

Although many highly effective methods of reversible contraception are available, high rates of unintended pregnancy and abortion provide evidence that current methods do not meet the needs of all couples. In recent years, a number of highly specific targets have been identified in key pathways that regulate the development of male and female gametes. Support for development of novel approaches has moved from industry to governmental and foundation funders. Continued public funding will be needed to move promising leads into clinical trials.

Probing cellular mechanics with Acoustic Force Spectroscopy.

PubMed

Sorkin, Raya; Bergamaschi, Giulia; Kamsma, Douwe; Brand, Guy; Dekel, Elya; Ofir-Birin, Yifat; Rudik, Ariel; Gironella, Marta; Ritort, Felix; Regev-Rudzki, Neta; Roos, Wouter; Wuite, Gijs J L

2018-06-21

A large number of studies demonstrate that cell mechanics and pathology are intimately linked. In particular, Red Blood Cell (RBC) deformability is key to their function, and is dramatically altered in the time course of diseases such as anemia and malaria. Due to the physiological importance of cell mechanics, many methods for cell mechanical probing have been developed. While single cell methods provide very valuable information, they are often technically challenging and lack high data throughput needed to distinguish differences in heterogeneous populations, while fluid flow high throughput methods miss the accuracy to detect subtle differences. Here, we present a new method for multiplexed single-cell mechanical probing using Acoustic Force Spectroscopy (AFS). We demonstrate that mechanical differences induced by chemical treatments of known effect can be measured and quantified. Furthermore, we explore the effect of extracellular-vesicles (EVs) uptake on RBC mechanics and demonstrate that EVs uptake increases RBC deformability. Our findings demonstrate the ability of AFS to manipulate cells with high stability and precision, and pave the way to further new insights into cellular mechanics and mechanobiology in health and disease, as well as potential biomedical applications.

Examination of the Measurement of Absorption Using the Reverberant Room Method for Highly Absorptive Acoustic Foam

NASA Technical Reports Server (NTRS)

Hughes, William O.; McNelis, Anne M.; Chris Nottoli; Eric Wolfram

2015-01-01

The absorption coefficient for material specimens are needed to quantify the expected acoustic performance of that material in its actual usage and environment. The ASTM C423-09a standard, "Standard Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberant Room Method" is often used to measure the absorption coefficient of material test specimens. This method has its basics in the Sabine formula. Although widely used, the interpretation of these measurements are a topic of interest. For example, in certain cases the measured Sabine absorption coefficients are greater than 1.0 for highly absorptive materials. This is often attributed to the diffraction edge effect phenomenon. An investigative test program to measure the absorption properties of highly absorbent melamine foam has been performed at the Riverbank Acoustical Laboratories. This paper will present and discuss the test results relating to the effect of the test materials' surface area, thickness and edge sealing conditions. A follow-on paper is envisioned that will present and discuss the results relating to the spacing between multiple piece specimens, and the mounting condition of the test specimen.

An Investigation of High-Order Shock-Capturing Methods for Computational Aeroacoustics

NASA Technical Reports Server (NTRS)

Casper, Jay; Baysal, Oktay

1997-01-01

Topics covered include: Low-dispersion scheme for nonlinear acoustic waves in nonuniform flow; Computation of acoustic scattering by a low-dispersion scheme; Algorithmic extension of low-dispersion scheme and modeling effects for acoustic wave simulation; The accuracy of shock capturing in two spatial dimensions; Using high-order methods on lower-order geometries; and Computational considerations for the simulation of discontinuous flows.

Transfer of a Mycobacterium tuberculosis genotyping method, Spoligotyping, from a reverse line-blot hybridization, membrane-based assay to the Luminex multianalyte profiling system.

PubMed

Cowan, Lauren S; Diem, Lois; Brake, Mary Catherine; Crawford, Jack T

2004-01-01

Spoligotyping using Luminex technology was shown to be a highly reproducible method suitable for high-throughput analysis. Spoligotyping of 48 isolates using the traditional membrane-based assay and the Luminex assay yielded concordant results for all isolates. The Luminex platform provides greater flexibility and cost effectiveness than the membrane-based assay.

The Problem of Reading and Reading Culture Improvement of Students-Bachelors of Elementary Education in Modern High Institution

ERIC Educational Resources Information Center

Kamalova, Lera A.; Koletvinova, Natal'ya D.

2016-01-01

This article is aimed to study the problems of reading and improve reading culture of students-bachelors of elementary education in modern high institutions and development of the most effective methods and techniques for improving of reading culture of students in the study of Humanities disciplines. The leading method to the study of this…

Teaching the Reading and Study Skills Needed in Junior High School Social Studies Classes.

ERIC Educational Resources Information Center

Davis, E. Dale

This study sought to identify effective methods that select, junior high school, social studies teachers found useful in promoting the reading and studying of printed materials. In the course of the research, 78 teachers identified specific procedures they had used to increase seventh, eighth, and ninth grade students' effectiveness in studying…

Effects of GO FASTER on Morpheme Definition Fluency for High School Students with High-Incidence Disabilities

ERIC Educational Resources Information Center

Fishley, Katelyn M.; Konrad, Moira; Hessler, Terri; Keesey, Susan

2012-01-01

Although vocabulary plays an important role in literacy and content instruction, there is a paucity of research identifying effective methods for teaching vocabulary. One promising strategy is morphemic analysis, which involves breaking words into morphemes, the smallest meaningful parts of words, and teaching students the meanings of those parts.…

Network Centric Warfare and the Changing Role of the Signal Corps

DTIC Science & Technology

2004-03-19

Internet; accessed 8 November 2003, A1-A2. 26 Steven R. Covey, 7 Habits of Highly Effective People , (New York, NY: Simon and Schuster, 1989), 98. 27...Methods, ed. Douglas V. Johnson “n.p.”, 2000. Covey, Steven R. 7 Habits of Highly Effective People . New York, NY: Simon and Schuster, 1989. French

Twelve-Month Effects of the COPE Healthy Lifestyles TEEN Program on Overweight and Depressive Symptoms in High School Adolescents

ERIC Educational Resources Information Center

Melnyk, Bernadette M.; Jacobson, Diana; Kelly, Stephanie A.; Belyea, Michael J.; Shaibi, Gabriel Q.; Small, Leigh; O'Haver, Judith A.; Marsiglia, Flavio F.

2015-01-01

Background: We evaluated the 12-month effects of the COPE (Creating Opportunities for Personal Empowerment) Healthy Lifestyles TEEN (Thinking, Emotions, Exercise, Nutrition) program versus an attention control program (Healthy Teens) on overweight/obesity and depressive symptoms in high school adolescents. Methods: A cluster randomized controlled…

Influence of the Level Density Parametrization on the Effective GDR Width at High Spins

NASA Astrophysics Data System (ADS)

Mazurek, K.; Matejska, M.; Kmiecik, M.; Maj, A.; Dudek, J.

Parameterizations of the nucleonic level densities are tested by computing the effective GDR strength-functions and GDR widths at high spins. Calculations are based on the thermal shape fluctuation method with the Lublin-Strasbourg Drop (LSD) model. Results for 106Sn, 147Eu, 176W, 194Hg are compared to the experimental data.

The New Hampshire High School Career Education Model. Final Report.

ERIC Educational Resources Information Center

Keene State Coll., NH.

The purpose of this project was to improve the quality and demonstrate the most effective methods and techniques of career education in four high schools in the state of New Hampshire. The focus was to effect change at two points: the first was the academic curriculum, where committees in each of the project schools reviewed their existing…

Effects of Printed, Pocket Electronic, and Online Dictionaries on High School Students' English Vocabulary Retention

ERIC Educational Resources Information Center

Chiu, Li-Ling; Liu, Gi-Zen

2013-01-01

This study obtained empirical evidence regarding the effects of using printed dictionaries (PD), pocket electronic dictionaries (PED), and online type-in dictionaries (OTID) on English vocabulary retention at a junior high school. A mixed-methods research methodology was adopted in this study. Thirty-three seventh graders were asked to use all…

In Search of the Reason for the Breathing Effect of MIL53 Metal-Organic Framework: An ab Initio Multiconfigurational Study.

PubMed

Weser, Oskar; Veryazov, Valera

2017-01-01

Multiconfigurational methods are applied to study electronic properties and structural changes in the highly flexible metal-organic framework MIL53(Cr). Via calculated bending potentials of angles, that change the most during phase transition, it is verified that the high flexibility of this material is not a question about special electronic properties in the coordination chemistry, but about overall linking of the framework. The complex posseses a demanding electronic structure with delocalized spin density, antifferomagnetic coupling and high multi-state character requiring multiconfigurational methods. Calculated properties are in good agreement with known experimental values confirming our chosen methods.

A study of high density bit transition requirements versus the effects on BCH error correcting coding

NASA Technical Reports Server (NTRS)

Ingels, F.; Schoggen, W. O.

1981-01-01

Several methods for increasing bit transition densities in a data stream are summarized, discussed in detail, and compared against constraints imposed by the 2 MHz data link of the space shuttle high rate multiplexer unit. These methods include use of alternate pulse code modulation waveforms, data stream modification by insertion, alternate bit inversion, differential encoding, error encoding, and use of bit scramblers. The psuedo-random cover sequence generator was chosen for application to the 2 MHz data link of the space shuttle high rate multiplexer unit. This method is fully analyzed and a design implementation proposed.

Computational Issues in Damping Identification for Large Scale Problems

NASA Technical Reports Server (NTRS)

Pilkey, Deborah L.; Roe, Kevin P.; Inman, Daniel J.

1997-01-01

Two damping identification methods are tested for efficiency in large-scale applications. One is an iterative routine, and the other a least squares method. Numerical simulations have been performed on multiple degree-of-freedom models to test the effectiveness of the algorithm and the usefulness of parallel computation for the problems. High Performance Fortran is used to parallelize the algorithm. Tests were performed using the IBM-SP2 at NASA Ames Research Center. The least squares method tested incurs high communication costs, which reduces the benefit of high performance computing. This method's memory requirement grows at a very rapid rate meaning that larger problems can quickly exceed available computer memory. The iterative method's memory requirement grows at a much slower pace and is able to handle problems with 500+ degrees of freedom on a single processor. This method benefits from parallelization, and significant speedup can he seen for problems of 100+ degrees-of-freedom.

Method of multi-mode vibration control for the carbody of high-speed electric multiple unit trains

NASA Astrophysics Data System (ADS)

Gong, Dao; Zhou, Jinsong; Sun, Wenjing; Sun, Yu; Xia, Zhanghui

2017-11-01

A method of multi-mode vibration control for the carbody of high-speed electric multiple unit (EMU) trains by using the onboard and suspended equipments as dynamic vibration absorbers (DVAs) is proposed. The effect of the multi-mode vibration on the ride quality of a high-speed EMU train was studied, and the target modes of vibration control were determined. An equivalent mass identification method was used to determine the equivalent mass for the target modes at the device installation positions. To optimize the vibration acceleration response of the carbody, the natural frequencies and damping ratios of the lateral and vertical vibration were designed based on the theory of dynamic vibration absorption. In order to realize the optimized design values of the natural frequencies for the lateral and vertical vibrations simultaneously, a new type of vibration absorber was designed in which a belleville spring and conventional rubber parts are connected in parallel. This design utilizes the negative stiffness of the belleville spring. Results show that, as compared to rigid equipment connections, the proposed method effectively reduces the multi-mode vibration of a carbody in a high-speed EMU train, thereby achieving the control objectives. The ride quality in terms of the lateral and vertical vibration of the carbody is considerably improved. Moreover, the optimal value of the damping ratio is effective in dissipating the vibration energy, which reduces the vibration of both the carbody and the equipment.

High temperature 1 MHz capacitance-voltage method for evaluation of border traps in 4H-SiC MOS system

NASA Astrophysics Data System (ADS)

Peng, Zhao-Yang; Wang, Sheng-Kai; Bai, Yun; Tang, Yi-Dan; Chen, Xi-Ming; Li, Cheng-Zhan; Liu, Ke-An; Liu, Xin-Yu

2018-04-01

In this work, border traps located in SiO2 at different depths in 4H-SiC MOS system are evaluated by a simple and effective method based on capacitance-voltage (C-V) measurements. This method estimates the border traps between two adjacent depths through C-V measurement at various frequencies at room and elevated temperatures. By comparison of these two C-V characteristics, the correlation between time constant of border traps and temperatures is obtained. Then the border trap density is determined by integration of capacitance difference against gate voltage at the regions where border traps dominate. The results reveal that border trap concentration a few nanometers away from the interface increases exponentially towards the interface, which is in good agreement with previous work. It has been proved that high temperature 1 MHz C-V method is effective for border trap evaluation.

Removal of central obscuration and spider arm effects with beam-shaping coronagraphy

NASA Astrophysics Data System (ADS)

Abe, L.; Murakami, N.; Nishikawa, J.; Tamura, M.

2006-05-01

This paper describes a method for removing the effect of a centrally obscured aperture with additional spider arms in arbitrary geometrical configurations. The proposed method is based on a two-stage process where the light beam is first shaped to remove the central obscuration and spider arms, in order to feed a second, highly efficient coronagraph. The beam-shaping stage is a combination of a diffraction mask in the first focal plane and a complex amplitude filter located in the conjugate pupil. This paper specifically describes the case of using Lyot occulting masks and circular phase-shifting masks as diffracting components. The basic principle of the method is given along with an analytical description and numerical simulations. Substantial improvement in the performance of high-contrast coronagraphs can be obtained with this method, even if the beam-shaping filter is not perfectly manufactured.

A novel approach to generating CER hypotheses based on mining clinical data.

PubMed

Zhang, Shuo; Li, Lin; Yu, Yiqin; Sun, Xingzhi; Xu, Linhao; Zhao, Wei; Teng, Xiaofei; Pan, Yue

2013-01-01

Comparative effectiveness research (CER) is a scientific method of investigating the effectiveness of alternative intervention methods. In a CER study, clinical researchers typically start with a CER hypothesis, and aim to evaluate it by applying a series of medical statistical methods. Traditionally, the CER hypotheses are defined manually by clinical researchers. This makes the task of hypothesis generation very time-consuming and the quality of hypothesis heavily dependent on the researchers' skills. Recently, with more electronic medical data being collected, it is highly promising to apply the computerized method for discovering CER hypotheses from clinical data sets. In this poster, we proposes a novel approach to automatically generating CER hypotheses based on mining clinical data, and presents a case study showing that the approach can facilitate clinical researchers to identify potentially valuable hypotheses and eventually define high quality CER studies.

Isolation of high quality RNA from cereal seeds containing high levels of starch.

PubMed

Wang, Guifeng; Wang, Gang; Zhang, Xiaowei; Wang, Fang; Song, Rentao

2012-01-01

Cereals are an important source of food, feed and fuel with a rapidly increasing global demand. However, cereal seeds contain high levels of starch and polysaccharides, making the isolation of high quality RNA extremely difficult. To develop a novel method for extracting high quality total RNA from various starch- and polysaccharides-rich cereal seeds, such as maize, rice, sorghum and wheat. We developed a modified sodium dodecyl sulphate (SDS)/TRIzol method. The combined use of a Tris buffer (pH 9.0) and SDS before TRIzol extraction effectively resolved the problem of seed homogenate solidification in such a buffer. A high concentration of SDS was used separately, not only to promote cell lysis but also to effectively dissolve seed sample containing high levels of starch. Moreover, acid phenol saturated with 0.1  M citrate buffer (pH 4.3) was used to separate RNA from DNAs, proteins and high levels of starch. This rapid protocol was compared with other RNA isolation methods preferentially used for plants rich in polysaccharides and secondary metabolites. Gel electrophoresis analysis indicated that the extracted total RNA had good integrity without apparent DNA contamination. Furthermore, an A₂₆₀/₂₈₀ ratio of approximately 2.0, an A₂₆₀/₂₃₀ ratio of more than 2.0 and RIN values of more than 8.6 indicated that the isolated RNA was of high purity. The isolated RNA was suitable for subsequent molecular manipulations, such as reverse-transcription polymerase chain reaction (PCR), rapid amplification of cDNA ends (RACE) and real-time PCR. The study has described an easy, efficient and highly reproducible method for RNA isolation from various cereal seeds. Copyright © 2011 John Wiley & Sons, Ltd.

Cross-correlation photothermal optical coherence tomography with high effective resolution.

PubMed

Tang, Peijun; Liu, Shaojie; Chen, Junbo; Yuan, Zhiling; Xie, Bingkai; Zhou, Jianhua; Tang, Zhilie

2017-12-01

We developed a cross-correlation photothermal optical coherence tomography (CC-PTOCT) system for photothermal imaging with high lateral and axial resolution. The CC-PTOCT system consists of a phase-sensitive OCT system, a modulated pumping laser, and a digital cross-correlator. The pumping laser was used to induce the photothermal effect in the sample, causing a slight phase modulation of the OCT signals. A spatial phase differentiation method was employed to reduce phase accumulation. The noise brought by the phase differentiation method and the strong background noise were suppressed efficiently by the cross-correlator, which was utilized to extract the photothermal signals from the modulated signals. Combining the cross-correlation technique with spatial phase differentiation can improve both lateral and axial resolution of the PTOCT imaging system. Clear photothermal images of blood capillaries of a mouse ear in vivo were successfully obtained with high lateral and axial resolution. The experimental results demonstrated that this system can enhance the effective transverse resolution, effective depth resolution, and contrast of the PTOCT image effectively, aiding the ongoing development of the accurate 3D functional imaging.

Based on the CSI regional segmentation indoor localization algorithm

NASA Astrophysics Data System (ADS)

Zeng, Xi; Lin, Wei; Lan, Jingwei

2017-08-01

To solve the problem of high cost and low accuracy, the method of Channel State Information (CSI) regional segmentation are proposed in the indoor positioning. Because Channel State Information (CSI) stability, and effective against multipath effect, we used the Channel State Information (CSI) to segment location area. The method Acquisition CSI the influence of different link to pinpoint the location of the area. Then the method can improve the accuracy of positioning, and reduce the cost of the fingerprint localization algorithm.

Methods for producing reinforced carbon nanotubes

DOEpatents

Ren, Zhifen [Newton, MA; Wen, Jian Guo [Newton, MA; Lao, Jing Y [Chestnut Hill, MA; Li, Wenzhi [Brookline, MA

2008-10-28

Methods for producing reinforced carbon nanotubes having a plurality of microparticulate carbide or oxide materials formed substantially on the surface of such reinforced carbon nanotubes composite materials are disclosed. In particular, the present invention provides reinforced carbon nanotubes (CNTs) having a plurality of boron carbide nanolumps formed substantially on a surface of the reinforced CNTs that provide a reinforcing effect on CNTs, enabling their use as effective reinforcing fillers for matrix materials to give high-strength composites. The present invention also provides methods for producing such carbide reinforced CNTs.

The convolutional differentiator method for numerical modelling of acoustic and elastic wavefields

NASA Astrophysics Data System (ADS)

Zhang, Zhong-Jie; Teng, Ji-Wen; Yang, Ding-Hui

1996-02-01

Based on the techniques of forward and inverse Fourier transformation, the authors discussed the design scheme of ordinary differentiator used and applied in the simulation of acoustic and elastic wavefields in isotropic media respectively. To compress Gibbs effects by truncation effectively, Hanning window is introduced in. The model computation shows that, the convolutional differentiator method has the advantages of rapidity, low requirements of computer’s inner storage and high precision, which is a potential method of numerical simulation.

Application of virtual phase-shifting speckle-interferometry for detection of polymorphism in the Chlamydia trachomatis omp1 gene

NASA Astrophysics Data System (ADS)

Feodorova, Valentina A.; Saltykov, Yury V.; Zaytsev, Sergey S.; Ulyanov, Sergey S.; Ulianova, Onega V.

2018-04-01

Method of phase-shifting speckle-interferometry has been used as a new tool with high potency for modern bioinformatics. Virtual phase-shifting speckle-interferometry has been applied for detection of polymorphism in the of Chlamydia trachomatis omp1 gene. It has been shown, that suggested method is very sensitive to natural genetic mutations as single nucleotide polymorphism (SNP). Effectiveness of proposed method has been compared with effectiveness of the newest bioinformatic tools, based on nucleotide sequence alignment.

Treatment of addiction and addiction-related behavior

DOEpatents

Dewey, Stephen L.; Brodie, Jonathan D.; Ashby, Jr., Charles R.

2004-12-07

The present invention provides a highly efficient method for treating substance addiction and for changing addiction-related behavior of a mammal suffering from substance addiction. The method includes administering to a mammal an effective amount of gamma vinylGABA or a pharmaceutically acceptable salt thereof. The present invention also provides a method of treatment of cocaine, morphine, heroin, nicotine, amphetamine, methamphetamine, or ethanol addiction by treating a mammal with an effective amount of gamma vinylGABA or a pharmaceutically acceptable salt thereof.

Method for extracting relevant electrical parameters from graphene field-effect transistors using a physical model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boscá, A., E-mail: alberto.bosca@upm.es; Dpto. de Ingeniería Electrónica, E.T.S.I. de Telecomunicación, Universidad Politécnica de Madrid, Madrid 28040; Pedrós, J.

2015-01-28

Due to its intrinsic high mobility, graphene has proved to be a suitable material for high-speed electronics, where graphene field-effect transistor (GFET) has shown excellent properties. In this work, we present a method for extracting relevant electrical parameters from GFET devices using a simple electrical characterization and a model fitting. With experimental data from the device output characteristics, the method allows to calculate parameters such as the mobility, the contact resistance, and the fixed charge. Differentiated electron and hole mobilities and direct connection with intrinsic material properties are some of the key aspects of this method. Moreover, the method outputmore » values can be correlated with several issues during key fabrication steps such as the graphene growth and transfer, the lithographic steps, or the metalization processes, providing a flexible tool for quality control in GFET fabrication, as well as a valuable feedback for improving the material-growth process.« less

Computer Reconstruction of Plant Growth and Chlorophyll Fluorescence Emission in Three Spatial Dimensions

PubMed Central

Bellasio, Chandra; Olejníčková, Julie; Tesař, Radek; Šebela, David; Nedbal, Ladislav

2012-01-01

Plant leaves grow and change their orientation as well their emission of chlorophyll fluorescence in time. All these dynamic plant properties can be semi-automatically monitored by a 3D imaging system that generates plant models by the method of coded light illumination, fluorescence imaging and computer 3D reconstruction. Here, we describe the essentials of the method, as well as the system hardware. We show that the technique can reconstruct, with a high fidelity, the leaf size, the leaf angle and the plant height. The method fails with wilted plants when leaves overlap obscuring their true area. This effect, naturally, also interferes when the method is applied to measure plant growth under water stress. The method is, however, very potent in capturing the plant dynamics under mild stress and without stress. The 3D reconstruction is also highly effective in correcting geometrical factors that distort measurements of chlorophyll fluorescence emission of naturally positioned plant leaves. PMID:22368511

Computer reconstruction of plant growth and chlorophyll fluorescence emission in three spatial dimensions.

PubMed

Bellasio, Chandra; Olejníčková, Julie; Tesař, Radek; Sebela, David; Nedbal, Ladislav

2012-01-01

Plant leaves grow and change their orientation as well their emission of chlorophyll fluorescence in time. All these dynamic plant properties can be semi-automatically monitored by a 3D imaging system that generates plant models by the method of coded light illumination, fluorescence imaging and computer 3D reconstruction. Here, we describe the essentials of the method, as well as the system hardware. We show that the technique can reconstruct, with a high fidelity, the leaf size, the leaf angle and the plant height. The method fails with wilted plants when leaves overlap obscuring their true area. This effect, naturally, also interferes when the method is applied to measure plant growth under water stress. The method is, however, very potent in capturing the plant dynamics under mild stress and without stress. The 3D reconstruction is also highly effective in correcting geometrical factors that distort measurements of chlorophyll fluorescence emission of naturally positioned plant leaves.

Effects of different drying methods on the product quality and volatile compounds of whole shiitake mushrooms.

PubMed

Tian, Yuting; Zhao, Yingting; Huang, Jijun; Zeng, Hongliang; Zheng, Baodong

2016-04-15

Various drying methods play important roles in the preservation of foods. However, how the different drying methods affect the quality of some foods is not clear. This paper evaluates the effects of hot air, vacuum, microwave, and microwave vacuum drying techniques on important qualities and volatile compounds of whole shiitake (Lentinus edodes) mushrooms. These four drying methods resulted in a significantly (p<0.05) increase in the content of total free amino acids and the relative content of sulfur compounds of dried products. Microwave vacuum drying helped to maintain larger amounts of taste-active amino acids, and improved nutrient retention and color attributes. Furthermore, the uniform honeycomb network created by microwave vacuum drying along with a less collapsed structure of dried samples can be used to explain the observed high rehydration ratio. Therefore, microwave vacuum drying should be a potential method for obtaining high-quality dried mushrooms. Copyright © 2015 Elsevier Ltd. All rights reserved.

Contact resistance extraction methods for short- and long-channel carbon nanotube field-effect transistors

NASA Astrophysics Data System (ADS)

Pacheco-Sanchez, Anibal; Claus, Martin; Mothes, Sven; Schröter, Michael

2016-11-01

Three different methods for the extraction of the contact resistance based on both the well-known transfer length method (TLM) and two variants of the Y-function method have been applied to simulation and experimental data of short- and long-channel CNTFETs. While for TLM special CNT test structures are mandatory, standard electrical device characteristics are sufficient for the Y-function methods. The methods have been applied to CNTFETs with low and high channel resistance. It turned out that the standard Y-function method fails to deliver the correct contact resistance in case of a relatively high channel resistance compared to the contact resistances. A physics-based validation is also given for the application of these methods based on applying traditional Si MOSFET theory to quasi-ballistic CNTFETs.

A path planning method used in fluid jet polishing eliminating lightweight mirror imprinting effect

NASA Astrophysics Data System (ADS)

Li, Wenzong; Fan, Bin; Shi, Chunyan; Wang, Jia; Zhuo, Bin

2014-08-01

With the development of space technology, the design of optical system tends to large aperture lightweight mirror with high dimension-thickness ratio. However, when the lightweight mirror PV value is less than λ/10 , the surface will show wavy imprinting effect obviously. Imprinting effect introduced by head-tool pressure has become a technological barrier in high-precision lightweight mirror manufacturing. Fluid jet polishing can exclude outside pressure. Presently, machining tracks often used are grating type path, screw type path and pseudo-random path. On the edge of imprinting error, the speed of adjacent path points changes too fast, which causes the machine hard to reflect quickly, brings about new path error, and increases the polishing time due to superfluous path. This paper presents a new planning path method to eliminate imprinting effect. Simulation results show that the path of the improved grating path can better eliminate imprinting effect compared to the general path.

Increasing Medicaid child health screenings: the effectiveness of mailed pamphlets, phone calls, and home visits.

PubMed Central

Selby-Harrington, M; Sorenson, J R; Quade, D; Stearns, S C; Tesh, A S; Donat, P L

1995-01-01

OBJECTIVES. A randomized controlled trial was conducted to test the effectiveness and cost effectiveness of three outreach interventions to promote well-child screening for children on Medicaid. METHODS. In rural North Carolina, a random sample of 2053 families with children due or overdue for screening was stratified according to the presence of a home phone. Families were randomly assigned to receive a mailed pamphlet and letter, a phone call, or a home visit outreach intervention, or the usual (control) method of informing at Medicaid intake. RESULTS. All interventions produced more screenings than the control method, but increases were significant only for families with phones. Among families with phones, a home visit was the most effective intervention but a phone call was the most cost-effective. However, absolute rates of effectiveness were low, and incremental costs per effect were high. CONCLUSIONS. Pamphlets, phone calls, and home visits by nurses were minimally effective for increasing well-child screenings. Alternate outreach methods are needed, especially for families without phones. PMID:7573627

Characterization of Bacterial Cellulose by Gluconacetobacter hansenii CGMCC 3917.

PubMed

Feng, Xianchao; Ullah, Niamat; Wang, Xuejiao; Sun, Xuchun; Li, Chenyi; Bai, Yun; Chen, Lin; Li, Zhixi

2015-10-01

In this study, comprehensive characterization and drying methods on properties of bacterial cellulose were analyzed. Bacterial cellulose was prepared by Gluconacetobacter hansenii CGMCC 3917, which was mutated by high hydrostatic pressure (HHP) treatment. Bacterial cellulose is mainly comprised of cellulose Iα with high crystallinity and purity. High-water holding and absorption capacity were examined by reticulated structure. Thermogravimetric analysis showed high thermal stability. High tensile strength and Young's modulus indicated its mechanical properties. The rheological analysis showed that bacterial cellulose had good consistency and viscosity. These results indicated that bacterial cellulose is a potential food additive and also could be used for a food packaging material. The high textural stability during freeze-thaw cycles makes bacterial cellulose an effective additive for frozen food products. In addition, the properties of bacterial cellulose can be affected by drying methods. Our results suggest that the bacterial cellulose produced from HHP-mutant strain has an effective characterization, which can be used for a wide range of applications in food industry. © 2015 Institute of Food Technologists®

Development and Evaluation of EPA Method 1615 for Detection of Enterovirus and Norovirus in Water

PubMed Central

Brinkman, Nichole E.; Griffin, Shannon M.; McMinn, Brian R.; Rhodes, Eric R.; Varughese, Eunice A.; Grimm, Ann C.; Parshionikar, Sandhya U.; Wymer, Larry; Fout, G. Shay

2013-01-01

The U.S. EPA developed a sample concentration and preparation assay in conjunction with the total culturable virus assay for concentrating and measuring culturable viruses in source and drinking waters as part of the Information Collection Rule (ICR) promulgated in 1996. In an effort to improve upon this method, the U.S. EPA recently developed Method 1615: Measurement of Enterovirus and Norovirus Occurrence in Water by Culture and RT-qPCR. Method 1615 uses a culturable virus assay with reduced equipment and labor costs compared to the costs associated with the ICR virus method and introduces a new molecular assay for the detection of enteroviruses and noroviruses by reverse transcription-quantitative PCR. In this study, we describe the optimization of several new components of the molecular assay and examine virus recovery from ground, reagent-grade, and surface water samples seeded with poliovirus type 3 and murine norovirus. For the culturable virus and molecular assays, mean poliovirus recovery using the complete method was 58% and 20% in groundwater samples, 122% and 39% using low-titer spikes in reagent-grade water, 42% and 48% using high-titer spikes in reagent-grade water, and 11% and 10% in surface water with high turbidity, respectively. Murine norovirus recovery by the molecular assay was 30% in groundwater samples, less than 8% in both low- and high-titer spikes in reagent-grade water, and 6% in surface water with high turbidity. This study demonstrates the effectiveness of Method 1615 for use with groundwater samples and highlights the need for further research into its effectiveness with surface water. PMID:23087037

Color calibration and fusion of lens-free and mobile-phone microscopy images for high-resolution and accurate color reproduction

NASA Astrophysics Data System (ADS)

Zhang, Yibo; Wu, Yichen; Zhang, Yun; Ozcan, Aydogan

2016-06-01

Lens-free holographic microscopy can achieve wide-field imaging in a cost-effective and field-portable setup, making it a promising technique for point-of-care and telepathology applications. However, due to relatively narrow-band sources used in holographic microscopy, conventional colorization methods that use images reconstructed at discrete wavelengths, corresponding to e.g., red (R), green (G) and blue (B) channels, are subject to color artifacts. Furthermore, these existing RGB colorization methods do not match the chromatic perception of human vision. Here we present a high-color-fidelity and high-resolution imaging method, termed “digital color fusion microscopy” (DCFM), which fuses a holographic image acquired at a single wavelength with a color-calibrated image taken by a low-magnification lens-based microscope using a wavelet transform-based colorization method. We demonstrate accurate color reproduction of DCFM by imaging stained tissue sections. In particular we show that a lens-free holographic microscope in combination with a cost-effective mobile-phone-based microscope can generate color images of specimens, performing very close to a high numerical-aperture (NA) benchtop microscope that is corrected for color distortions and chromatic aberrations, also matching the chromatic response of human vision. This method can be useful for wide-field imaging needs in telepathology applications and in resource-limited settings, where whole-slide scanning microscopy systems are not available.

Object Manifold Alignment for Multi-Temporal High Resolution Remote Sensing Images Classification

NASA Astrophysics Data System (ADS)

Gao, G.; Zhang, M.; Gu, Y.

2017-05-01

Multi-temporal remote sensing images classification is very useful for monitoring the land cover changes. Traditional approaches in this field mainly face to limited labelled samples and spectral drift of image information. With spatial resolution improvement, "pepper and salt" appears and classification results will be effected when the pixelwise classification algorithms are applied to high-resolution satellite images, in which the spatial relationship among the pixels is ignored. For classifying the multi-temporal high resolution images with limited labelled samples, spectral drift and "pepper and salt" problem, an object-based manifold alignment method is proposed. Firstly, multi-temporal multispectral images are cut to superpixels by simple linear iterative clustering (SLIC) respectively. Secondly, some features obtained from superpixels are formed as vector. Thirdly, a majority voting manifold alignment method aiming at solving high resolution problem is proposed and mapping the vector data to alignment space. At last, all the data in the alignment space are classified by using KNN method. Multi-temporal images from different areas or the same area are both considered in this paper. In the experiments, 2 groups of multi-temporal HR images collected by China GF1 and GF2 satellites are used for performance evaluation. Experimental results indicate that the proposed method not only has significantly outperforms than traditional domain adaptation methods in classification accuracy, but also effectively overcome the problem of "pepper and salt".

Color calibration and fusion of lens-free and mobile-phone microscopy images for high-resolution and accurate color reproduction

PubMed Central

Zhang, Yibo; Wu, Yichen; Zhang, Yun; Ozcan, Aydogan

2016-01-01

Lens-free holographic microscopy can achieve wide-field imaging in a cost-effective and field-portable setup, making it a promising technique for point-of-care and telepathology applications. However, due to relatively narrow-band sources used in holographic microscopy, conventional colorization methods that use images reconstructed at discrete wavelengths, corresponding to e.g., red (R), green (G) and blue (B) channels, are subject to color artifacts. Furthermore, these existing RGB colorization methods do not match the chromatic perception of human vision. Here we present a high-color-fidelity and high-resolution imaging method, termed “digital color fusion microscopy” (DCFM), which fuses a holographic image acquired at a single wavelength with a color-calibrated image taken by a low-magnification lens-based microscope using a wavelet transform-based colorization method. We demonstrate accurate color reproduction of DCFM by imaging stained tissue sections. In particular we show that a lens-free holographic microscope in combination with a cost-effective mobile-phone-based microscope can generate color images of specimens, performing very close to a high numerical-aperture (NA) benchtop microscope that is corrected for color distortions and chromatic aberrations, also matching the chromatic response of human vision. This method can be useful for wide-field imaging needs in telepathology applications and in resource-limited settings, where whole-slide scanning microscopy systems are not available. PMID:27283459

Chemical Differentiation of Dendrobium officinale and Dendrobium devonianum by Using HPLC Fingerprints, HPLC-ESI-MS, and HPTLC Analyses

PubMed Central

Ye, Zi; Dai, Jia-Rong; Zhang, Cheng-Gang; Lu, Ye; Wu, Lei-Lei; Gong, Amy G. W.; Wang, Zheng-Tao

2017-01-01

The stems of Dendrobium officinale Kimura et Migo (Dendrobii Officinalis Caulis) have a high medicinal value as a traditional Chinese medicine (TCM). Because of the limited supply, D. officinale is a high priced TCM, and therefore adulterants are commonly found in the herbal market. The dried stems of a closely related Dendrobium species, Dendrobium devonianum Paxt., are commonly used as the substitute; however, there is no effective method to distinguish the two Dendrobium species. Here, a high performance liquid chromatography (HPLC) method was successfully developed and applied to differentiate D. officinale and D. devonianum by comparing the chromatograms according to the characteristic peaks. A HPLC coupled with electrospray ionization multistage mass spectrometry (HPLC-ESI-MS) method was further applied for structural elucidation of 15 flavonoids, 5 phenolic acids, and 1 lignan in D. officinale. Among these flavonoids, 4 flavonoid C-glycosides were firstly reported in D. officinale, and violanthin and isoviolanthin were identified to be specific for D. officinale compared with D. devonianum. Then, two representative components were used as chemical markers. A rapid and reliable high performance thin layer chromatography (HPTLC) method was applied in distinguishing D. officinale from D. devonianum. The results of this work have demonstrated that these developed analytical methods can be used to discriminate D. officinale and D. devonianum effectively and conveniently. PMID:28769988

Color calibration and fusion of lens-free and mobile-phone microscopy images for high-resolution and accurate color reproduction.

PubMed

Zhang, Yibo; Wu, Yichen; Zhang, Yun; Ozcan, Aydogan

2016-06-10

Lens-free holographic microscopy can achieve wide-field imaging in a cost-effective and field-portable setup, making it a promising technique for point-of-care and telepathology applications. However, due to relatively narrow-band sources used in holographic microscopy, conventional colorization methods that use images reconstructed at discrete wavelengths, corresponding to e.g., red (R), green (G) and blue (B) channels, are subject to color artifacts. Furthermore, these existing RGB colorization methods do not match the chromatic perception of human vision. Here we present a high-color-fidelity and high-resolution imaging method, termed "digital color fusion microscopy" (DCFM), which fuses a holographic image acquired at a single wavelength with a color-calibrated image taken by a low-magnification lens-based microscope using a wavelet transform-based colorization method. We demonstrate accurate color reproduction of DCFM by imaging stained tissue sections. In particular we show that a lens-free holographic microscope in combination with a cost-effective mobile-phone-based microscope can generate color images of specimens, performing very close to a high numerical-aperture (NA) benchtop microscope that is corrected for color distortions and chromatic aberrations, also matching the chromatic response of human vision. This method can be useful for wide-field imaging needs in telepathology applications and in resource-limited settings, where whole-slide scanning microscopy systems are not available.

Probabilistic analysis of wind-induced vibration mitigation of structures by fluid viscous dampers

NASA Astrophysics Data System (ADS)

Chen, Jianbing; Zeng, Xiaoshu; Peng, Yongbo

2017-11-01

The high-rise buildings usually suffer from excessively large wind-induced vibrations, and thus vibration control systems might be necessary. Fluid viscous dampers (FVDs) with nonlinear power law against velocity are widely employed. With the transition of design method from traditional frequency domain approaches to more refined direct time domain approaches, the difficulty of time integration of these systems occurs sometimes. In the present paper, firstly the underlying reason of the difficulty is revealed by identifying that the equations of motion of high-rise buildings installed with FVDs are sometimes stiff differential equations. Thus, an approach effective for stiff differential systems, i.e., the backward difference formula (BDF), is then introduced, and verified to be effective for the equation of motion of wind-induced vibration controlled systems. Comparative studies are performed among some methods, including the Newmark method, KR-alpha method, energy-based linearization method and the statistical linearization method. Based on the above results, a 20-story steel frame structure is taken as a practical example. Particularly, the randomness of structural parameters and of wind loading input is emphasized. The extreme values of the responses are examined, showing the effectiveness of the proposed approach, and also necessitating the refined probabilistic analysis in the design of wind-induced vibration mitigation systems.

Nanoscale zero-valent metals: a review of synthesis, characterization, and applications to environmental remediation.

PubMed

Li, Lingyun; Hu, Jiwei; Shi, Xuedan; Fan, Mingyi; Luo, Jin; Wei, Xionghui

2016-09-01

Engineered nanoscale zero-valent metals (NZVMs) representing the forefront of technologies have been considered as promising materials for environmental remediation and antimicrobial effect, due to their high reducibility and strong adsorption capability. This review is focused on the methodology for synthesis of bare NZVMs, supported NZVMs, modified NZVMs, and bimetallic systems with both traditional and green methods. Recent studies have demonstrated that self-assembly methods can play an important role for obtaining ordered, controllable, and tunable NZVMs. In addition to common characterization methods, the state-of-the-art methods have been developed to obtain the properties of NZVMs (e.g., granularity, size distribution, specific surface area, shape, crystal form, and chemical bond) with the resolution down to subnanometer scale. These methods include spherical aberration corrected scanning transmission electron microscopy (Cs-corrected STEM), electron energy-loss spectroscopy (EELS), and near edge X-ray absorption fine structure (NEXAFS). A growing body of experimental data has proven that nanoscale zero-valent iron (NZVI) is highly effective and versatile. This article discusses the applications of NZVMs to treatment of heavy metals, halogenated organic compounds, polycyclic aromatic hydrocarbons, nutrients, radioelements, and microorganisms, using both ex situ and in situ methods. Furthermore, this paper briefly describes the ecotoxicological effects for NZVMs and the research prospects related to their synthesis, modification, characterization, and applications.

Broadband metamaterial lens antennas with special properties by controlling both refractive-index distribution and feed directivity

NASA Astrophysics Data System (ADS)

Ma, Qian; Shi, Chuan Bo; Chen, Tian Yi; Qing Qi, Mei; Li, Yun Bo; Cui, Tie Jun

2018-04-01

A new method is proposed to design gradient refractive-index metamaterial lens antennas by optimizing both the refractive-index distribution of the lens and the feed directivity. Comparing to the conventional design methods, source optimization provides a new degree of freedom to control aperture fields effectively. To demonstrate this method, two lenses with special properties based on this method are designed, to emit high-efficiency plane waves and fan-shaped beams, respectively. Both lenses have good performance and wide frequency band from 12 to 18 GHz, verifying the validity of the proposed method. The plane-wave emitting lens realized a high aperture efficiency of 75%, and the fan-beam lens achieved a high gain of 15 dB over board bandwidth. The experimental results have good agreement with the design targets and full-wave simulations.

Navier-Stokes Analysis of a High Wing Transport High-Lift Configuration with Externally Blown Flaps

NASA Technical Reports Server (NTRS)

Slotnick, Jeffrey P.; An, Michael Y.; Mysko, Stephen J.; Yeh, David T.; Rogers, Stuart E.; Roth, Karlin; Baker, M.David; Nash, S.

2000-01-01

Insights and lessons learned from the aerodynamic analysis of the High Wing Transport (HWT) high-lift configuration are presented. Three-dimensional Navier-Stokes CFD simulations using the OVERFLOW flow solver are compared with high Reynolds test data obtained in the NASA Ames 12 Foot Pressure Wind Tunnel (PWT) facility. Computational analysis of the baseline HWT high-lift configuration with and without Externally Blown Flap (EBF) jet effects is highlighted. Several additional aerodynamic investigations, such as nacelle strake effectiveness and wake vortex studies, are presented. Technical capabilities and shortcomings of the computational method are discussed and summarized.

Development of a high sensitivity pinhole type gamma camera using semiconductors for low dose rate fields

NASA Astrophysics Data System (ADS)

Ueno, Yuichiro; Takahashi, Isao; Ishitsu, Takafumi; Tadokoro, Takahiro; Okada, Koichi; Nagumo, Yasushi; Fujishima, Yasutake; Yoshida, Akira; Umegaki, Kikuo

2018-06-01

We developed a pinhole type gamma camera, using a compact detector module of a pixelated CdTe semiconductor, which has suitable sensitivity and quantitative accuracy for low dose rate fields. In order to improve the sensitivity of the pinhole type semiconductor gamma camera, we adopted three methods: a signal processing method to set the discriminating level lower, a high sensitivity pinhole collimator and a smoothing image filter that improves the efficiency of the source identification. We tested basic performances of the developed gamma camera and carefully examined effects of the three methods. From the sensitivity test, we found that the effective sensitivity was about 21 times higher than that of the gamma camera for high dose rate fields which we had previously developed. We confirmed that the gamma camera had sufficient sensitivity and high quantitative accuracy; for example, a weak hot spot (0.9 μSv/h) around a tree root could be detected within 45 min in a low dose rate field test, and errors of measured dose rates with point sources were less than 7% in a dose rate accuracy test.

Comparison of three protein extraction procedures from toxic and non-toxic dinoflagellates for proteomics analysis.

PubMed

Jiang, Xi-Wen; Wang, Jing; Chan, Leo Lai; Lam, Paul Kwan Sing; Gu, Ji-Dong

2015-08-01

Three methods for extraction and preparation of high-quality proteins from both toxic and non-toxic dinoflagellates for proteomics analysis, including Trizol method, Lysis method and Tris method, were compared with the subsequent protein separation profiles using 2-D differential gel electrophoresis (2-D DIGE), Coomassie Blue and silver staining. These methods showed suitability for proteins with different pIs and molecular weights. Tris method was better for low molecular weight and low pI protein isolation; whereas both Lysis and Trizol method were better for high-molecular weight and high pI protein purification. Trizol method showed good results with Alexandrium species and Gynodinium species, and the background in gel was much clearer than the other two methods. At the same time, only Lysis method caused breaking down of the target proteins. On the other hand, Trizol method obtained higher concentration of ribulose-1,5-bisphosphate carboxylase/oxygenase proteins by Western-blotting, while Tris method was the best for peridinin-chlorophyll-protein complexes protein and T1 protein preparation. DIGE was better than Coomassie Blue and silver staining, except for some limitations, such as the high cost of the dyes, relatively short shelf life and the requirements for extensive and special image capturing equipment. Some proteins related to PSTs synthesis in dinoflagellates are hydrophobic with high molecular weight or binding on membranes and Trizol method performed better than Tris method for these proteins. The Trizol method and 2-D DIGE were effective combination for proteomics investigations of dinoflagellates. This procedure allows reliable and high recovery efficiency of proteins from dinoflagellates for better understanding on their occurrence and toxin-production for physiological and biochemical information.

Effects of assumed tow architecture on the predicted moduli and stresses in woven composites

NASA Technical Reports Server (NTRS)

Chapman, Clinton Dane

1994-01-01

This study deals with the effect of assumed tow architecture on the elastic material properties and stress distributions of plain weave woven composites. Specifically, the examination of how a cross-section is assumed to sweep-out the tows of the composite is examined in great detail. The two methods studied are extrusion and translation. This effect is also examined to determine how sensitive this assumption is to changes in waviness ratio. 3D finite elements were used to study a T300/Epoxy plain weave composite with symmetrically stacked mats. 1/32nd of the unit cell is shown to be adequate for analysis of this type of configuration with the appropriate set of boundary conditions. At low waviness, results indicate that for prediction of elastic properties, either method is adequate. At high waviness, certain elastic properties become more sensitive to the method used. Stress distributions at high waviness ratio are shown to vary greatly depending on the type of loading applied. At low waviness, both methods produce similar results.

High-Throughput Quantitation of Neonicotinoids in Lyophilized Surface Water by LC-APCI-MS/MS.

PubMed

Morrison, Lucas M; Renaud, Justin B; Sabourin, Lyne; Sumarah, Mark W; Yeung, Ken K C; Lapen, David R

2018-05-21

Background : Neonicotinoids are among the most widely used insecticides. Recently, there has been concern associated with unintended adverse effects on honeybees and aquatic invertebrates at low parts-per-trillion levels. Objective : There is a need for LC-MS/MS methods that are capable of high-throughput measurements of the most widely used neonicotinoids at environmentally relevant concentrations in surface water. Methods : This method allows for quantitation of acetamiprid, clothianidin, imidacloprid, dinotefuran, nitenpyram, thiacloprid, and thiamethoxam in surface water. Deuterated internal standards are added to 20 mL environmental samples, which are concentrated by lyophilisation and reconstituted with methanol followed by acetonitrile. Results : A large variation of mean recovery efficiencies across five different surface water sampling sites within this study was observed, ranging from 45 to 74%. This demonstrated the need for labelled internal standards to compensate for these differences. Atmospheric pressure chemical ionization (APCI) performed better than electrospray ionization (ESI) with limited matrix suppression, achieving 71-110% of the laboratory fortified blank signal. Neonicotinoids were resolved on a C18 column using a 5 min LC method, in which MQL ranged between 0.93 and 4.88 ng/L. Conclusions : This method enables cost effective, accurate, and reproducible monitoring of these pesticides in the aquatic environment. Highlights : Lyophilization is used for high throughput concentration of neonicotinoids in surface water. Variations in matrix effects between samples was greatly reduced by using APCI compared with ESI. Clothianidin and thiamethoxam were detected in all samples with levels ranging from below method quantitation limit to 65 ng/L.

Resonance tube phonation in water: High-speed imaging, electroglottographic and oral pressure observations of vocal fold vibrations--a pilot study.

PubMed

Granqvist, Svante; Simberg, Susanna; Hertegård, Stellan; Holmqvist, Sofia; Larsson, Hans; Lindestad, Per-Åke; Södersten, Maria; Hammarberg, Britta

2015-10-01

Phonation into glass tubes ('resonance tubes'), keeping the free end of the tube in water, has been a frequently used voice therapy method in Finland and more recently also in other countries. The purpose of this exploratory study was to investigate what effects tube phonation with and without water has on the larynx. Two participants were included in the study. The methods used were high-speed imaging, electroglottographic observations of vocal fold vibrations, and measurements of oral pressure during tube phonation. Results showed that the fluctuation in the back pressure during tube phonation in water altered the vocal fold vibrations. In the high-speed imaging, effects were found in the open quotient and amplitude variation of the glottal opening. The open quotient increased with increasing water depth (from 2 cm to 6 cm). A modulation effect by the water bubbles on the vocal fold vibrations was seen both in the high-speed glottal area tracings and in the electroglottography signal. A second experiment revealed that the increased average oral pressure was largely determined by the water depth. The increased open quotient can possibly be explained by an increased abduction of the vocal folds and/or a reduced transglottal pressure. The back pressure of the bubbles also modulates glottal vibrations with a possible 'massage' effect on the vocal folds. This effect and the well-defined average pressure increase due to the known water depth are different from those of other methods using a semi-occluded vocal tract.

Microelectrode array recordings of cardiac action potentials as a high throughput method to evaluate pesticide toxicity.

PubMed

Natarajan, A; Molnar, P; Sieverdes, K; Jamshidi, A; Hickman, J J

2006-04-01

The threat of environmental pollution, biological warfare agent dissemination and new diseases in recent decades has increased research into cell-based biosensors. The creation of this class of sensors could specifically aid the detection of toxic chemicals and their effects in the environment, such as pyrethroid pesticides. Pyrethroids are synthetic pesticides that have been used increasingly over the last decade to replace other pesticides like DDT. In this study we used a high-throughput method to detect pyrethroids by using multielectrode extracellular recordings from cardiac cells. The data from this cell-electrode hybrid system was compared to published results obtained with patch-clamp electrophysiology and also used as an alternative method to further understand pyrethroid effects. Our biosensor consisted of a confluent monolayer of cardiac myocytes cultured on microelectrode arrays (MEA) composed of 60 substrate-integrated electrodes. Spontaneous activity of these beating cells produced extracellular field potentials in the range of 100 microV to nearly 1200 microV with a beating frequency of 0.5-4 Hz. All of the tested pyrethroids; alpha-Cypermethrin, Tetramethrin and Tefluthrin, produced similar changes in the electrophysiological properties of the cardiac myocytes, namely reduced beating frequency and amplitude. The sensitivity of our toxin detection method was comparable to earlier patch-clamp studies, which indicates that, in specific applications, high-throughput extracellular methods can replace single-cell studies. Moreover, the similar effect of all three pyrethroids on the measured parameters suggests, that not only detection of the toxins but, their classification might also be possible with this method. Overall our results support the idea that whole cell biosensors might be viable alternatives when compared to current toxin detection methods.

Comparison of two hardware-based hit filtering methods for trackers in high-pileup environments

NASA Astrophysics Data System (ADS)

Gradin, J.; Mårtensson, M.; Brenner, R.

2018-04-01

As experiments in high energy physics aim to measure increasingly rare processes, the experiments continually strive to increase the expected signal yields. In the case of the High Luminosity upgrade of the LHC, the luminosity is raised by increasing the number of simultaneous proton-proton interactions, so-called pile-up. This increases the expected yields of signal and background processes alike. The signal is embedded in a large background of processes that mimic that of signal events. It is therefore imperative for the experiments to develop new triggering methods to effectively distinguish the interesting events from the background. We present a comparison of two methods for filtering detector hits to be used for triggering on particle tracks: one based on a pattern matching technique using Associative Memory (AM) chips and the other based on the Hough transform. Their efficiency and hit rejection are evaluated for proton-proton collisions with varying amounts of pile-up using a simulation of a generic silicon tracking detector. It is found that, while both methods are feasible options for a track trigger with single muon efficiencies around 98–99%, the AM based pattern matching produces a lower number of hit combinations with respect to the Hough transform whilst keeping more of the true signal hits. We also present the effect on the two methods of increasing the amount of support material in the detector and of introducing inefficiencies by deactivating detector modules. The increased support material has negligable effects on the efficiency for both methods, while dropping 5% (10%) of the available modules decreases the efficiency to about 95% (87%) for both methods, irrespective of the amount of pile-up.

The Effects of Problem-Solving Teaching on Creative Thinking among District 2 High School Students in Sari City.

PubMed

Nozari, Ali Yazdanpanah; Siamian, Hasan

2014-12-01

Nowadays, regarding the learners' needs and social conditions, it is obviously needed to revise and reconsider the traditional methods and approaches in teaching. The problem solving approach is one of the new ways in Teaching and learning process. This study aimed at studying and examining the effect of "problem-solving" approach on creative thinking of high school female students. An experimental method is used for this research. In this research, 342 out of 3047 female-students from Sari high schools were randomly selected. These 342 students were divided into two groups (experimental and control) in which there were seven classrooms. The total number of students in every group was about 171. After testing them with Jamal Abedi creativity test, it was revealed that two groups were equal in creativity score. The tests were done through Requirements. The experimental group was taught by problem solving method for three months while the control group was taught by traditional method. The research results showed that using descriptive indices and t-test for the two independent sample groups in which problem solving teaching method was used in teaching processes had an effect on creativity level in comparison with traditional method used in the control group. Considering the results of this study, the application of problem-solving teaching methods increased the creativity and its components (fluidity, expansion, originality and flexibility) in learners, therefore, it is recommended that students be encouraged to take classes on frequent responses on various topics (variability) and draw attention on different issues, and expand their analysis on elements in particular courses like art (expansion). To enhance the learner's mental flexibility and attention to various aspects, they are encouraged to provide a variety of responses.

Reconciling Data from Different Sources: Practical Realities of Using Mixed Methods to Identify Effective High School Practices

ERIC Educational Resources Information Center

Smith, Thomas M.; Cannata, Marisa; Haynes, Katherine Taylor

2016-01-01

Background/Context: Mixed methods research conveys multiple advantages to the study of complex phenomena and large organizations or systems. The benefits are derived from drawing on the strengths of qualitative methods to answer questions about how and why a phenomenon occurs and those of quantitative methods to examine how often a phenomenon…

Concerns regarding 24-h sampling for formaldehyde, acetaldehyde, and acrolein using 2,4-dinitrophenylhydrazine (DNPH)-coated solid sorbents

NASA Astrophysics Data System (ADS)

Herrington, Jason S.; Hays, Michael D.

2012-08-01

There is high demand for accurate and reliable airborne carbonyl measurement methods due to the human and environmental health impacts of carbonyls and their effects on atmospheric chemistry. Standardized 2,4-dinitrophenylhydrazine (DNPH)-based sampling methods are frequently applied for measuring gaseous carbonyls in the atmospheric environment. However, there are multiple short-comings associated with these methods that detract from an accurate understanding of carbonyl-related exposure, health effects, and atmospheric chemistry. The purpose of this brief technical communication is to highlight these method challenges and their influence on national ambient monitoring networks, and to provide a logical path forward for accurate carbonyl measurement. This manuscript focuses on three specific carbonyl compounds of high toxicological interest—formaldehyde, acetaldehyde, and acrolein. Further method testing and development, the revision of standardized methods, and the plausibility of introducing novel technology for these carbonyls are considered elements of the path forward. The consolidation of this information is important because it seems clear that carbonyl data produced utilizing DNPH-based methods are being reported without acknowledgment of the method short-comings or how to best address them.

Sparse Additive Ordinary Differential Equations for Dynamic Gene Regulatory Network Modeling.

PubMed

Wu, Hulin; Lu, Tao; Xue, Hongqi; Liang, Hua

2014-04-02

The gene regulation network (GRN) is a high-dimensional complex system, which can be represented by various mathematical or statistical models. The ordinary differential equation (ODE) model is one of the popular dynamic GRN models. High-dimensional linear ODE models have been proposed to identify GRNs, but with a limitation of the linear regulation effect assumption. In this article, we propose a sparse additive ODE (SA-ODE) model, coupled with ODE estimation methods and adaptive group LASSO techniques, to model dynamic GRNs that could flexibly deal with nonlinear regulation effects. The asymptotic properties of the proposed method are established and simulation studies are performed to validate the proposed approach. An application example for identifying the nonlinear dynamic GRN of T-cell activation is used to illustrate the usefulness of the proposed method.

Evaluation of three different methods of distance learning for postgraduate diagnostic imaging education: A pilot study.

PubMed

Poirier, Jean-Nicolas; Cooley, Jeffrey R; Wessely, Michelle; Guebert, Gary M; Petrocco-Napuli, Kristina

2014-10-01

Objective : The purpose of this study was to evaluate the perceived effectiveness and learning potential of 3 Web-based educational methods in a postgraduate radiology setting. Methods : Three chiropractic radiology faculty from diverse geographic locations led mini-courses using asynchronous discussion boards, synchronous Web conferencing, and asynchronous voice-over case presentations formatted for Web viewing. At the conclusion of each course, participants filled out a 14-question survey (using a 5-point Likert scale) designed to evaluate the effectiveness of each method in achieving specified course objectives and goals and their satisfaction when considering the learning potential of each method. The mean, standard deviation, and percentage agreements were tabulated. Results : Twenty, 15, and 10 participants completed the discussion board, Web conferencing, and case presentation surveys, respectively. All educational methods demonstrated a high level of agreement regarding the course objective (total mean rating >4.1). The case presentations had the highest overall rating for achieving the course goals; however, all but one method still had total mean ratings >4.0 and overall agreement levels of 70%-100%. The strongest potential for interactive learning was found with Web conferencing and discussion boards, while case presentations rated very low in this regard. Conclusions : The perceived effectiveness in achieving the course objective and goals was high for each method. Residency-based distance education may be a beneficial adjunct to current methods of training, allowing for international collaboration. When considering all aspects tested, there does not appear to be a clear advantage to any one method. Utilizing various methods may be most appropriate.

Detecting and treating occlusal caries lesions: a cost-effectiveness analysis.

PubMed

Schwendicke, F; Stolpe, M; Meyer-Lueckel, H; Paris, S

2015-02-01

The health gains and costs resulting from using different caries detection strategies might not only depend on the accuracy of the used method but also the treatment emanating from its use in different populations. We compared combinations of visual-tactile, radiographic, or laser-fluorescence-based detection methods with 1 of 3 treatments (non-, micro-, and invasive treatment) initiated at different cutoffs (treating all or only dentinal lesions) in populations with low or high caries prevalence. A Markov model was constructed to follow an occlusal surface in a permanent molar in an initially 12-y-old male German patient over his lifetime. Prevalence data and transition probabilities were extracted from the literature, while validity parameters of different methods were synthesized or obtained from systematic reviews. Microsimulations were performed to analyze the model, assuming a German health care setting and a mixed public-private payer perspective. Radiographic and fluorescence-based methods led to more overtreatments, especially in populations with low prevalence. For the latter, combining visual-tactile or radiographic detection with microinvasive treatment retained teeth longest (mean 66 y) at lowest costs (329 and 332 Euro, respectively), while combining radiographic or fluorescence-based detections with invasive treatment was the least cost-effective (<60 y, >700 Euro). In populations with high prevalence, combining radiographic detection with microinvasive treatment was most cost-effective (63 y, 528 Euro), while sensitive detection methods combined with invasive treatments were again the least cost-effective (<59 y, >690 Euro). The suitability of detection methods differed significantly between populations, and the cost-effectiveness was greatly influenced by the treatment initiated after lesion detection. The accuracy of a detection method relative to a "gold standard" did not automatically convey into better health or reduced costs. Detection methods should be evaluated not only against their criterion validity but also the long-term effects resulting from their use in different populations. © International & American Associations for Dental Research 2014.

Dual-circuit, multiple-effect refrigeration system and method

DOEpatents

DeVault, Robert C.

1995-01-01

A dual circuit absorption refrigeration system comprising a high temperature single-effect refrigeration loop and a lower temperature double-effect refrigeration loop separate from one another and provided with a double-condenser coupling therebetween. The high temperature condenser of the single-effect refrigeration loop is double coupled to both of the generators in the double-effect refrigeration loop to improve internal heat recovery and a heat and mass transfer additive such as 2-ethyl-1-hexanol is used in the lower temperature double-effect refrigeration loop to improve the performance of the absorber in the double-effect refrigeration loop.

Analysis on the effectiveness of gifted education by studying perceptions of science gifted education recipients

NASA Astrophysics Data System (ADS)

Jung, Hyun-Chul; Ryu, Chun-Ryol; Choi, Jinsu; Park, Kyeong-Jin

2016-04-01

The necessity of science gifted education is persistently emphasized in the aspect of developing individuals' potential abilities and enhancing national competitiveness. In the case of Korea, gifted education has been conducted on a national level ever since the country established legal and institutional strategies for gifted education in 2000. Even though 15 years has passed since a full-scale implementation of gifted education has started, there are few researches on the effectiveness of gifted education. Therefore, considering the splashdown effect, that a long period of time is needed to obtain reliable assessments on education effectiveness, this research surveyed gifted education recipients to study the effectiveness of gifted education. For this cause, we developed an questionnaire and conducted a survey of university students who had experience of receiving science gifted education. We deduced the following from the analysis. First, generally the recipients were satisfied with their gifted education experiences, but thought that not enough opportunities were provided on problem solving ability enhancement and career related aspects. Second, schools considered 'experiments' as the most effective teaching method, regardless to the stage of education. In addition, they perceived 'discussions and presentations' as effective education methods for elementary school students; 'theme investigating classes' for middle school students; and lectures for high school students. It could be seen that various experiences were held important for elementary school students and as students went into high school education, more emphasis was placed on the importance of understanding mathematical and scientific facts. Third, on gifted education teaching staffs, satisfaction of professionalism on specialities were high but satisfaction of variety of teaching methods were relatively low. In this research, to encourage science gifted students to meet their potentials, we propose the following: a variety of gifted education programs which could not be provided in regular curriculums, expansion in career education programs on finding careers in science technology, and the necessity of teacher training to enhance gifted education teaching method professionalism. Keywords : science gifted education, recipients, effectiveness of education, education program, teaching method, teacher professionalism

[Effect of high-intensity interval training on the reduction of glycosylated hemoglobin in type-2 diabetic adult patients].

PubMed

Aguilera Eguía, Raúl Alberto; Russell Guzmán, Javier Antonio; Soto Muñoz, Marcelo Enrique; Villegas González, Bastián Eduardo; Poblete Aro, Carlos Emilio; Ibacache Palma, Alejandro

2015-03-05

Type 2 diabetes mellitus is one of the major non-communicable chronic diseases in the world. Its prevalence in Chile is significant, and complications associated with this disease involve great costs, which is why prevention and treatment of this condition are essential. Physical exercise is an effective means for prevention and treatment of type 2 diabetes mellitus. The emergence of new forms of physical training, such as "high intensity interval training", presents novel therapeutic alternatives for patients and health care professionals. To assess the validity and applicability of the results regarding the effectiveness of high intensity interval training in reducing glycosylated hemoglobin in adult patients with type 2 diabetes mellitus and answer the following question: In subjects with type 2 diabetes, can the method of high intensity interval training compared to moderate intensity exercise decrease glycosylated hemoglobin? We performed a critical analysis of the article "Feasibility and preliminary effectiveness of high intensity interval training in type 2 diabetes". We found no significant differences in the amount of glycosylated hemoglobin between groups of high intensity interval training and moderate-intensity exercise upon completion of the study (p>0.05). In adult patients with type 2 diabetes mellitus, high intensity interval training does not significantly improve glycosylated hemoglobin levels. Despite this, the high intensity interval training method shows as much improvement in body composition and physical condition as the moderate intensity exercise program.

Ultra-sensitive, stable isotope assisted quantification of multiple urinary mycotoxin exposure biomarkers.

PubMed

Šarkanj, Bojan; Ezekiel, Chibundu N; Turner, Paul C; Abia, Wilfred A; Rychlik, Michael; Krska, Rudolf; Sulyok, Michael; Warth, Benedikt

2018-08-17

There is a critical need to better understand the patterns, levels and combinatory effects of exposures we are facing through our diet and environment. Mycotoxin mixtures are of particular concern due to chronic low dose exposures caused by naturally contaminated food. To facilitate new insights into their role in chronic disease, mycotoxins and their metabolites are quantified in bio-fluids as biomarkers of exposure. Here, we describe a highly sensitive urinary assay based on ultra-high performance liquid chromatography - tandem mass spectrometer (UHPLC-MS/MS) and 13 C-labelled or deuterated internal standards covering the most relevant regulated and emerging mycotoxins. Utilizing enzymatic pre-treatment, solid phase extraction and UHPLC separation, the sensitivity of the method was significantly higher (10-160x lower LODs) than in a previously described method used for comparison purpose, and stable isotopes provided compensation for challenging matrix effects. This method was in-house validated and applied to re-assess mycotoxin exposure in urine samples obtained from Nigerian children, adolescent and adults, naturally exposed through their regular diet. Owing to the methods high sensitivity, biomarkers were detected in all samples. The mycoestrogen zearalenone was the most frequently detected contaminant (82%) but also ochratoxin A (76%), aflatoxin M 1 (73%) and fumonisin B 1 (71%) were quantified in a large share of urines. Overall, 57% of 120 urines were contaminated with both, aflatoxin M 1 and fumonisin B 1 , and other co-exposures were frequent. These results clearly demonstrate the advanced performance of the method to assess lowest background exposures (pg mL -1 range) using a single, highly robust assay that will allow for the systematic investigation of low dose effects on human health. Copyright © 2018 The Authors. Published by Elsevier B.V. All rights reserved.

Quantifying the effectiveness of ecological restoration projects on long-term vegetation dynamics in the karst regions of Southwest China

NASA Astrophysics Data System (ADS)

Tong, Xiaowei; Wang, Kelin; Yue, Yuemin; Brandt, Martin; Liu, Bo; Zhang, Chunhua; Liao, Chujie; Fensholt, Rasmus

2017-02-01

To alleviate the severe rocky desertification and improve the ecological degradation conditions in Southwest China, the national and local Chinese governments have implemented a series of Ecological Restoration Projects (ERPs) since the late 1990s. This study proposed a remote sensing based approach to evaluate the long-term efforts of the ERPs started in 2000. The method applies a time-series trend analysis of satellite based vegetation data corrected for climatic influences to reveal human induced vegetation changes. The improved residual method is combined with statistics on the invested project funds to derive an index, Project Effectiveness Index (PEI), measuring the project effectiveness at county scale. High effectiveness is detected in the Guangxi Province, moderate effectiveness in the Guizhou Province, and low and no effectiveness in the Yunnan Province. Successful implementations are closely related to the combined influences from climatic conditions and human management. The landforms of Peak Forest Plain and Peak Cluster Depression regions in the Guangxi Province are characterized by temperate climate with sufficient rainfall generally leading to a high effectiveness. For the karst regions of the Yunnan and Guizhou Provinces with rough terrain and lower rainfall combined with poor management practices (unsuitable species selection, low compensation rate for peasants), only low or even no effect of project implementations can be observed. However, the effectiveness distribution is not homogeneous and counties with high project effectiveness in spite of complex natural conditions were identified, while counties with negative vegetation trends despite relatively favorable conditions and high investments were also distinguished. The proposed framework is expected to be of high relevance in general monitoring of the successfulness of ecological conservation projects in relation to invested funds.

Inferring probabilistic stellar rotation periods using Gaussian processes

NASA Astrophysics Data System (ADS)

Angus, Ruth; Morton, Timothy; Aigrain, Suzanne; Foreman-Mackey, Daniel; Rajpaul, Vinesh

2018-02-01

Variability in the light curves of spotted, rotating stars is often non-sinusoidal and quasi-periodic - spots move on the stellar surface and have finite lifetimes, causing stellar flux variations to slowly shift in phase. A strictly periodic sinusoid therefore cannot accurately model a rotationally modulated stellar light curve. Physical models of stellar surfaces have many drawbacks preventing effective inference, such as highly degenerate or high-dimensional parameter spaces. In this work, we test an appropriate effective model: a Gaussian Process with a quasi-periodic covariance kernel function. This highly flexible model allows sampling of the posterior probability density function of the periodic parameter, marginalizing over the other kernel hyperparameters using a Markov Chain Monte Carlo approach. To test the effectiveness of this method, we infer rotation periods from 333 simulated stellar light curves, demonstrating that the Gaussian process method produces periods that are more accurate than both a sine-fitting periodogram and an autocorrelation function method. We also demonstrate that it works well on real data, by inferring rotation periods for 275 Kepler stars with previously measured periods. We provide a table of rotation periods for these and many more, altogether 1102 Kepler objects of interest, and their posterior probability density function samples. Because this method delivers posterior probability density functions, it will enable hierarchical studies involving stellar rotation, particularly those involving population modelling, such as inferring stellar ages, obliquities in exoplanet systems, or characterizing star-planet interactions. The code used to implement this method is available online.

Distortion correction in EPI at ultra-high-field MRI using PSF mapping with optimal combination of shift detection dimension.

PubMed

Oh, Se-Hong; Chung, Jun-Young; In, Myung-Ho; Zaitsev, Maxim; Kim, Young-Bo; Speck, Oliver; Cho, Zang-Hee

2012-10-01

Despite its wide use, echo-planar imaging (EPI) suffers from geometric distortions due to off-resonance effects, i.e., strong magnetic field inhomogeneity and susceptibility. This article reports a novel method for correcting the distortions observed in EPI acquired at ultra-high-field such as 7 T. Point spread function (PSF) mapping methods have been proposed for correcting the distortions in EPI. The PSF shift map can be derived either along the nondistorted or the distorted coordinates. Along the nondistorted coordinates more information about compressed areas is present but it is prone to PSF-ghosting artifacts induced by large k-space shift in PSF encoding direction. In contrast, shift maps along the distorted coordinates contain more information in stretched areas and are more robust against PSF-ghosting. In ultra-high-field MRI, an EPI contains both compressed and stretched regions depending on the B0 field inhomogeneity and local susceptibility. In this study, we present a new geometric distortion correction scheme, which selectively applies the shift map with more information content. We propose a PSF-ghost elimination method to generate an artifact-free pixel shift map along nondistorted coordinates. The proposed method can correct the effects of the local magnetic field inhomogeneity induced by the susceptibility effects along with the PSF-ghost artifact cancellation. We have experimentally demonstrated the advantages of the proposed method in EPI data acquisitions in phantom and human brain using 7-T MRI. Copyright © 2011 Wiley Periodicals, Inc.

Spatial analysis on human brucellosis incidence in mainland China: 2004–2010

PubMed Central

Zhang, Junhui; Yin, Fei; Zhang, Tao; Yang, Chao; Zhang, Xingyu; Feng, Zijian; Li, Xiaosong

2014-01-01

Objectives China has experienced a sharply increasing rate of human brucellosis in recent years. Effective spatial monitoring of human brucellosis incidence is very important for successful implementation of control and prevention programmes. The purpose of this paper is to apply exploratory spatial data analysis (ESDA) methods and the empirical Bayes (EB) smoothing technique to monitor county-level incidence rates for human brucellosis in mainland China from 2004 to 2010 by examining spatial patterns. Methods ESDA methods were used to characterise spatial patterns of EB smoothed incidence rates for human brucellosis based on county-level data obtained from the China Information System for Disease Control and Prevention (CISDCP) in mainland China from 2004 to 2010. Results EB smoothed incidence rates for human brucellosis were spatially dependent during 2004–2010. The local Moran test identified significantly high-risk clusters of human brucellosis (all p values <0.01), which persisted during the 7-year study period. High-risk counties were centred in the Inner Mongolia Autonomous Region and other Northern provinces (ie, Hebei, Shanxi, Jilin and Heilongjiang provinces) around the border with the Inner Mongolia Autonomous Region where animal husbandry was highly developed. The number of high-risk counties increased from 25 in 2004 to 54 in 2010. Conclusions ESDA methods and the EB smoothing technique can assist public health officials in identifying high-risk areas. Allocating more resources to high-risk areas is an effective way to reduce human brucellosis incidence. PMID:24713215

Interactive laboratory classes enhance neurophysiological knowledge in Thai medical students.

PubMed

Wongjarupong, Nicha; Niyomnaitham, Danai; Vilaisaktipakorn, Pitchamol; Suksiriworaboot, Tanawin; Qureshi, Shaun Peter; Bongsebandhu-Phubhakdi, Saknan

2018-03-01

Interactive laboratory class (ILC) is a two-way communication teaching method that encourages students to correlate laboratory findings with materials from lectures. In Thai medical education, active learning methods are uncommon. This paper aims to establish 1) if ILCs would effectively promote physiology learning; 2) if effectiveness would be found in both previously academically high-performing and low-performing students; and 3) the acceptability of ILCs to Thai medical students as a novel learning method. Two hundred seventy-eight second-year medical students were recruited to this study. We conducted three ILC sessions, which followed corresponding lectures. We carried out multiple-choice pre- and post-ILC assessments of knowledge and compared by repeated-measures ANOVA and unpaired t-test. Subgroup analysis was performed to compare high-performance (HighP) and low-performance (LowP) students. After the ILCs, participants self-rated their knowledge and satisfaction. Post-ILC test scores increased significantly compared with pre-ILC test scores in all three sessions. Mean scores of each post-ILC test increased significantly from pre-ILC test in both LowP and HighP groups. More students self-reported a "very high" and "high" level of knowledge after ILCs. Most students agreed that ILCs provided more discussion opportunity, motivated their learning, and made lessons more enjoyable. As an adjunct to lectures, ILCs can enhance knowledge in medical students, regardless of previous academic performance. Students perceived ILC as useful and acceptable. This study supports the active learning methods in physiology education, regardless of cultural context.

Significant Returns in Engagement and Performance with a Free Teaching App

ERIC Educational Resources Information Center

Green, Alan

2016-01-01

Pedagogical research shows that teaching methods other than traditional lectures may result in better outcomes. However, lecture remains the dominant method in economics, likely due to high implementation costs of methods shown to be effective in the literature. In this article, the author shows significant benefits of using a teaching app for…

Method for improving fuel cell performance

DOEpatents

Uribe, Francisco A.; Zawodzinski, Thomas

2003-10-21

A method is provided for operating a fuel cell at high voltage for sustained periods of time. The cathode is switched to an output load effective to reduce the cell voltage at a pulse width effective to reverse performance degradation from OH adsorption onto cathode catalyst surfaces. The voltage is stepped to a value of less than about 0.6 V to obtain the improved and sustained performance.

Integrated Methods for Pupils To Reinforce Occupational and Verbal Effectiveness (Project IMPROVE). Final Evaluation Report, 1992-93. OREA Report.

ERIC Educational Resources Information Center

Guadalupe, Deana R.

Integrated Methods for Pupils to Reinforce Occupational and Vocational Effectiveness (Project IMPROVE) was a federally funded project in its second year of operation in two Manhattan (New York) high schools in 1992-93. It served limited-English-proficient students, 186 Latino and 13 Asian-American, in grades 9-12. Students received instruction in…

Direct immersion single drop micro-extraction method for multi-class pesticides analysis in mango using GC-MS.

PubMed

Pano-Farias, Norma S; Ceballos-Magaña, Silvia G; Muñiz-Valencia, Roberto; Jurado, Jose M; Alcázar, Ángela; Aguayo-Villarreal, Ismael A

2017-12-15

Due the negative effects of pesticides on environment and human health, more efficient and environmentally friendly methods are needed. In this sense, a simple, fast, free from memory effects and economical direct-immersion single drop micro-extraction (SDME) method and GC-MS for multi-class pesticides determination in mango samples was developed. Sample pre-treatment using ultrasound-assisted solvent extraction and factors affecting the SDME procedure (extractant solvent, drop volume, stirring rate, ionic strength, time, pH and temperature) were optimized using factorial experimental design. This method presented high sensitive (LOD: 0.14-169.20μgkg -1 ), acceptable precision (RSD: 0.7-19.1%), satisfactory recovery (69-119%) and high enrichment factors (20-722). Several obtained LOQs are below the MRLs established by the European Commission; therefore, the method could be applied for pesticides determination in routing analysis and custom laboratories. Moreover, this method has shown to be suitable for determination of some of the studied pesticides in lime, melon, papaya, banana, tomato, and lettuce. Copyright © 2017 Elsevier Ltd. All rights reserved.

Competencies Used to Evaluate High School Coaches.

ERIC Educational Resources Information Center

Gratto, John

1983-01-01

Studies of how to evaluate high school coaches' effectiveness found that most respondents felt that principals, athletic directors, and coaches should jointly arrive at a method of evaluation. Coaching competencies rated most highly included prevention and care of athletic injuries, supervision, and consistent discipline. Other valued competencies…

School Counsellors' Perceptions on Working with Student High-Risk Behaviour

ERIC Educational Resources Information Center

Harris, Gregory E.; Jeffery, Gary

2010-01-01

The current exploratory-descriptive study used a survey design method to examine guidance counsellors' and educational psychologists' perceptions of their preparation, motivation, and effectiveness in preventing, assessing, and intervening into student high-risk behaviour. The study also explored training associated with addressing high-risk…

Advanced Computational Methods for High-accuracy Refinement of Protein Low-quality Models

NASA Astrophysics Data System (ADS)

Zang, Tianwu

Predicting the 3-dimentional structure of protein has been a major interest in the modern computational biology. While lots of successful methods can generate models with 3˜5A root-mean-square deviation (RMSD) from the solution, the progress of refining these models is quite slow. It is therefore urgently needed to develop effective methods to bring low-quality models to higher-accuracy ranges (e.g., less than 2 A RMSD). In this thesis, I present several novel computational methods to address the high-accuracy refinement problem. First, an enhanced sampling method, named parallel continuous simulated tempering (PCST), is developed to accelerate the molecular dynamics (MD) simulation. Second, two energy biasing methods, Structure-Based Model (SBM) and Ensemble-Based Model (EBM), are introduced to perform targeted sampling around important conformations. Third, a three-step method is developed to blindly select high-quality models along the MD simulation. These methods work together to make significant refinement of low-quality models without any knowledge of the solution. The effectiveness of these methods is examined in different applications. Using the PCST-SBM method, models with higher global distance test scores (GDT_TS) are generated and selected in the MD simulation of 18 targets from the refinement category of the 10th Critical Assessment of Structure Prediction (CASP10). In addition, in the refinement test of two CASP10 targets using the PCST-EBM method, it is indicated that EBM may bring the initial model to even higher-quality levels. Furthermore, a multi-round refinement protocol of PCST-SBM improves the model quality of a protein to the level that is sufficient high for the molecular replacement in X-ray crystallography. Our results justify the crucial position of enhanced sampling in the protein structure prediction and demonstrate that a considerable improvement of low-accuracy structures is still achievable with current force fields.

A Protocol for Functional Assessment of Whole-Protein Saturation Mutagenesis Libraries Utilizing High-Throughput Sequencing.

PubMed

Stiffler, Michael A; Subramanian, Subu K; Salinas, Victor H; Ranganathan, Rama

2016-07-03

Site-directed mutagenesis has long been used as a method to interrogate protein structure, function and evolution. Recent advances in massively-parallel sequencing technology have opened up the possibility of assessing the functional or fitness effects of large numbers of mutations simultaneously. Here, we present a protocol for experimentally determining the effects of all possible single amino acid mutations in a protein of interest utilizing high-throughput sequencing technology, using the 263 amino acid antibiotic resistance enzyme TEM-1 β-lactamase as an example. In this approach, a whole-protein saturation mutagenesis library is constructed by site-directed mutagenic PCR, randomizing each position individually to all possible amino acids. The library is then transformed into bacteria, and selected for the ability to confer resistance to β-lactam antibiotics. The fitness effect of each mutation is then determined by deep sequencing of the library before and after selection. Importantly, this protocol introduces methods which maximize sequencing read depth and permit the simultaneous selection of the entire mutation library, by mixing adjacent positions into groups of length accommodated by high-throughput sequencing read length and utilizing orthogonal primers to barcode each group. Representative results using this protocol are provided by assessing the fitness effects of all single amino acid mutations in TEM-1 at a clinically relevant dosage of ampicillin. The method should be easily extendable to other proteins for which a high-throughput selection assay is in place.

Objective evaluation of the knocking sound of a diesel engine considering the temporal and frequency masking effect simultaneously

NASA Astrophysics Data System (ADS)

Yun, Dong-Un; Lee, Sang-Kwon

2017-06-01

In this paper, we present a novel method for an objective evaluation of knocking noise emitted by diesel engines based on the temporal and frequency masking theory. The knocking sound of a diesel engine is a vibro-acoustic sound correlated with the high-frequency resonances of the engine structure and a periodic impulsive sound with amplitude modulation. Its period is related to the engine speed and includes specific frequency bands related to the resonances of the engine structure. A knocking sound with the characteristics of a high-frequency impulsive wave can be masked by low-frequency sounds correlated with the harmonics of the firing frequency and broadband noise. The degree of modulation of the knocking sound signal was used for such objective evaluations in previous studies, without considering the masking effect. However, the frequency masking effect must be considered for the objective evaluation of the knocking sound. In addition to the frequency masking effect, the temporal masking effect occurs because the period of the knocking sound changes according to the engine speed. Therefore, an evaluation method considering the temporal and frequency masking effect is required to analyze the knocking sound objectively. In this study, an objective evaluation method considering the masking effect was developed based on the masking theory of sound and signal processing techniques. The method was applied successfully for the objective evaluation of the knocking sound of a diesel engine.

Unstructured High-Order Galerkin-Temporal- Boundary Methods for the Klein-Gordon Equation with Non-Reflecting Boundary Conditions

DTIC Science & Technology

2010-06-01

9 C. Conservation of Momentum . . . . . . . . . . . . . . . . . . . . . 11 1. Gravity Effects . . . . . . . . . . . . . . . . . . . . . . . . . 12 2...describe the high-order spectral element method used to discretize the problem in space (up to 16th order polynomials ) in Chapter IV. Chapter V discusses...inertial frame. Body forces are those acting on the fluid volume that are proportional to the mass. The body forces considered here are gravity and

Laser light-scattering spectroscopy: a new application in the study of ciliary activity.

PubMed Central

Lee, W I; Verdugo, P

1976-01-01

A uniquely precise and simple method to study ciliary activity by laser light-scattering spectroscopy has been developed and validated. A concurrent study of the effect of Ca2+ on ciliary activity in vitro by laser scattering spectroscopy and high speed cinematography has demonstrated that this new method is simpler and as accurate and reproducible as the high speed film technique. PMID:963208

Method and apparatus for cooling high temperature superconductors with neon-nitrogen mixtures

DOEpatents

Laverman, Royce J.; Lai, Ban-Yen

1993-01-01

Apparatus and methods for cooling high temperature superconducting materials (HTSC) to superconductive temperatures within the range of 27.degree. K. to 77.degree. K. using a mixed refrigerant consisting of liquefied neon and nitrogen containing up to about ten mole percent neon by contacting and surrounding the HTSC material with the mixed refrigerant so that free convection or forced flow convection heat transfer can be effected.

Flows about a rotating circular cylinder by the discrete-vortex method

NASA Astrophysics Data System (ADS)

Kimura, Takeyoshi; Tsutahara, Michihisa

1987-01-01

A numerical study has been conducted for flows past a rotating circular cylinder at high Reynolds numbers, using the discrete-vortex method. It is noted that the reverse Magnus effect is caused by the retreat of the separation point on the acceleration side. At high rotating speed, the nascent vortices of opposite directions are mixed faster, the wake becomes narrower, and predominating frequencies in the lift force disappear.

A review of surface energy balance models for estimating actual evapotranspiration with remote sensing at high spatiotemporal resolution over large extents

Treesearch

Ryan R. McShane; Katelyn P. Driscoll; Roy Sando

2017-01-01

Many approaches have been developed for measuring or estimating actual evapotranspiration (ETa), and research over many years has led to the development of remote sensing methods that are reliably reproducible and effective in estimating ETa. Several remote sensing methods can be used to estimate ETa at the high spatial resolution of agricultural fields and the large...

Transfer of a Mycobacterium tuberculosis Genotyping Method, Spoligotyping, from a Reverse Line-Blot Hybridization, Membrane-Based Assay to the Luminex Multianalyte Profiling System

PubMed Central

Cowan, Lauren S.; Diem, Lois; Brake, Mary Catherine; Crawford, Jack T.

2004-01-01

Spoligotyping using Luminex technology was shown to be a highly reproducible method suitable for high-throughput analysis. Spoligotyping of 48 isolates using the traditional membrane-based assay and the Luminex assay yielded concordant results for all isolates. The Luminex platform provides greater flexibility and cost effectiveness than the membrane-based assay. PMID:14715809

Simulation of thermal transpiration flow using a high-order moment method

NASA Astrophysics Data System (ADS)

Sheng, Qiang; Tang, Gui-Hua; Gu, Xiao-Jun; Emerson, David R.; Zhang, Yong-Hao

2014-04-01

Nonequilibrium thermal transpiration flow is numerically analyzed by an extended thermodynamic approach, a high-order moment method. The captured velocity profiles of temperature-driven flow in a parallel microchannel and in a micro-chamber are compared with available kinetic data or direct simulation Monte Carlo (DSMC) results. The advantages of the high-order moment method are shown as a combination of more accuracy than the Navier-Stokes-Fourier (NSF) equations and less computation cost than the DSMC method. In addition, the high-order moment method is also employed to simulate the thermal transpiration flow in complex geometries in two types of Knudsen pumps. One is based on micro-mechanized channels, where the effect of different wall temperature distributions on thermal transpiration flow is studied. The other relies on porous structures, where the variation of flow rate with a changing porosity or pore surface area ratio is investigated. These simulations can help to optimize the design of a real Knudsen pump.

The Nature, Causes and Effects of School Violence in South African High Schools

ERIC Educational Resources Information Center

Ncontsa, Vusumzi Nelson; Shumba, Almon

2013-01-01

We sought to investigate the nature, causes and effects of school violence in four South African high schools. A purposive sample of five principals, 80 learners and 20 educators was selected from the four schools used in the study. A sequential mixed method approach was used in this study; both questionnaires and interviews were used. The design…

Effect of a Sport Education Program on Motivation for Physical Education and Leisure-Time Physical Activity

ERIC Educational Resources Information Center

Wallhead, Tristan L.; Garn, Alex C.; Vidoni, Carla

2014-01-01

Purpose: The purpose of this study was to examine the effect of a high school sport education curriculum program on students' motivation for physical education and leisure-time physical activity. Method: Participants were 568 high school students enrolled in the required physical education programs at 2 schools, 1 taught using sport education and…

The Effects of Math Acceleration in Middle School at the High School Level

ERIC Educational Resources Information Center

Dossenbach, Chris Payton

2017-01-01

The purpose of this mixed-methods capstone is to investigate the effectiveness of the math acceleration initiative that began in the studied school district in 2009 and the impact the initiative has had on mathematics enrollment at the high school level. This research project followed cohorts of students during the 2012-2013 and 2013-2014 school…

High- and Low-Level Dissonance-Based Eating Disorder Prevention Programs with Young Women with Body Image Concerns: An Experimental Trial

ERIC Educational Resources Information Center

McMillan, Whitney; Stice, Eric; Rohde, Paul

2011-01-01

Objective: As cognitive dissonance is theorized to contribute to the effects of dissonance-based eating disorder prevention programs, we evaluated a high-dissonance version of this program against a low-dissonance version and a wait-list control condition to provide an experimental test of the mechanism of intervention effects. Method: Female…

Procedural Adaptations for Use of Constant Time Delay to Teach Highly Motivating Words to Beginning Braille Readers

ERIC Educational Resources Information Center

Ivy, Sarah E.; Guerra, Jennifer A.; Hatton, Deborah D.

2017-01-01

Introduction: Constant time delay is an evidence-based practice to teach sight word recognition to students with a variety of disabilities. To date, two studies have documented its effectiveness for teaching braille. Methods: Using a multiple-baseline design, we evaluated the effectiveness of constant time delay to teach highly motivating words to…

A Study of Principals' Instructional Leadership Behaviors and Beliefs of Good Pedagogical Practice among Effective California High Schools Serving Socioeconomically Disadvantaged and English Learners

ERIC Educational Resources Information Center

Peariso, Jamon Frederick

2011-01-01

This mixed methods descriptive and causal-comparative study investigates what instructional leadership behaviors effective California high school principals have and what their beliefs are in regards to pedagogy, related issues, and professional issues, either constructivist or instructivist in nature, in the environment of the current NCLB…

Fuzzy method of recognition of high molecular substances in evidence-based biology

NASA Astrophysics Data System (ADS)

Olevskyi, V. I.; Smetanin, V. T.; Olevska, Yu. B.

2017-10-01

Nowadays modern requirements to achieving reliable results along with high quality of researches put mathematical analysis methods of results at the forefront. Because of this, evidence-based methods of processing experimental data have become increasingly popular in the biological sciences and medicine. Their basis is meta-analysis, a method of quantitative generalization of a large number of randomized trails contributing to a same special problem, which are often contradictory and performed by different authors. It allows identifying the most important trends and quantitative indicators of the data, verification of advanced hypotheses and discovering new effects in the population genotype. The existing methods of recognizing high molecular substances by gel electrophoresis of proteins under denaturing conditions are based on approximate methods for comparing the contrast of electrophoregrams with a standard solution of known substances. We propose a fuzzy method for modeling experimental data to increase the accuracy and validity of the findings of the detection of new proteins.

High-Fidelity Roadway Modeling and Simulation

NASA Technical Reports Server (NTRS)

Wang, Jie; Papelis, Yiannis; Shen, Yuzhong; Unal, Ozhan; Cetin, Mecit

2010-01-01

Roads are an essential feature in our daily lives. With the advances in computing technologies, 2D and 3D road models are employed in many applications, such as computer games and virtual environments. Traditional road models were generated by professional artists manually using modeling software tools such as Maya and 3ds Max. This approach requires both highly specialized and sophisticated skills and massive manual labor. Automatic road generation based on procedural modeling can create road models using specially designed computer algorithms or procedures, reducing the tedious manual editing needed for road modeling dramatically. But most existing procedural modeling methods for road generation put emphasis on the visual effects of the generated roads, not the geometrical and architectural fidelity. This limitation seriously restricts the applicability of the generated road models. To address this problem, this paper proposes a high-fidelity roadway generation method that takes into account road design principles practiced by civil engineering professionals, and as a result, the generated roads can support not only general applications such as games and simulations in which roads are used as 3D assets, but also demanding civil engineering applications, which requires accurate geometrical models of roads. The inputs to the proposed method include road specifications, civil engineering road design rules, terrain information, and surrounding environment. Then the proposed method generates in real time 3D roads that have both high visual and geometrical fidelities. This paper discusses in details the procedures that convert 2D roads specified in shape files into 3D roads and civil engineering road design principles. The proposed method can be used in many applications that have stringent requirements on high precision 3D models, such as driving simulations and road design prototyping. Preliminary results demonstrate the effectiveness of the proposed method.

Resonance Rayleigh scattering method for highly sensitive detection of chitosan using aniline blue as probe

NASA Astrophysics Data System (ADS)

Zhang, Weiai; Ma, Caijuan; Su, Zhengquan; Bai, Yan

2016-11-01

This paper describes a highly sensitive and accurate approach using aniline blue (AB) (water soluble) as a probe to determine chitosan (CTS) through Resonance Rayleigh scattering (RRS). Under optimum experimental conditions, the intensities of RRS were linearly proportional to the concentration of CTS in the range from 0.01 to 3.5 μg/mL, and the limit of detection (LOD) was 6.94 ng/mL. Therefore, a new and highly sensitive method based on RRS for the determination of CTS has been developed. Furthermore, the effect of molecular weight of CTS and the effect of the degree of deacetylation of CTS on the accurate quantification of CTS was studied. The experimental data was analyzed by linear regression analysis, which indicated that the molecular weight and the degree of deacetylation of CTS had no statistical significance and this method could be used to determine CTS accurately. Meanwhile, this assay was applied for CTS determination in health products with satisfactory results.

Highly precise acoustic calibration method of ring-shaped ultrasound transducer array for plane-wave-based ultrasound tomography

NASA Astrophysics Data System (ADS)

Terada, Takahide; Yamanaka, Kazuhiro; Suzuki, Atsuro; Tsubota, Yushi; Wu, Wenjing; Kawabata, Ken-ichi

2017-07-01

Ultrasound computed tomography (USCT) is promising for a non-invasive, painless, operator-independent and quantitative system for breast-cancer screening. Assembly error, production tolerance, and aging-degradation variations of the hardwire components, particularly of plane-wave-based USCT systems, may hamper cost effectiveness, precise imaging, and robust operation. The plane wave is transmitted from a ring-shaped transducer array for receiving the signal at a high signal-to-noise-ratio and fast aperture synthesis. There are four signal-delay components: response delays in the transmitters and receivers and propagation delays depending on the positions of the transducer elements and their directivity. We developed a highly precise calibration method for calibrating these delay components and evaluated it with our prototype plane-wave-based USCT system. Our calibration method was found to be effective in reducing delay errors. Gaps and curves were eliminated from the plane wave, and echo images of wires were sharpened in the entire imaging area.

Effect of amylose content and nanoclay incorporation order in physicochemical properties of starch/montmorillonite composites.

PubMed

Romero-Bastida, C A; Tapia-Blácido, D R; Méndez-Montealvo, G; Bello-Pérez, L A; Velázquez, G; Alvarez-Ramirez, J

2016-11-05

The effects of the amylose content and the preparation sequence in physicochemical properties of starch/montmorillonite (MMT) composites were studied in this work. Native (30%) and high amylose Hylon VII (70%) starches were considered for assessing the effects of amylose content. Glycerol and MMT were used as additives to evaluate the effects of the former as plasticizer and the latter as reinforcer. The glycerol was incorporated before (Method M1) and after (Method M2) the addition of MMT. FTIR studies indicated that water bonding was affected by amylose content. Sorption isotherms indicated that method M2 favoured water adsorption and method M1 reduced water adsorption due to competition for active sites for interaction. TGA showed that method M1 induced a higher degradation rate than method M2. Wettability analysis by contact angle measurements showed that plasticizer promoted the hydrophilicity of the film, whereas MMT promoted a hydrophobic surface for both cases of amylose content. Copyright © 2016. Published by Elsevier Ltd.

A high-order multiscale finite-element method for time-domain acoustic-wave modeling

NASA Astrophysics Data System (ADS)

Gao, Kai; Fu, Shubin; Chung, Eric T.

2018-05-01

Accurate and efficient wave equation modeling is vital for many applications in such as acoustics, electromagnetics, and seismology. However, solving the wave equation in large-scale and highly heterogeneous models is usually computationally expensive because the computational cost is directly proportional to the number of grids in the model. We develop a novel high-order multiscale finite-element method to reduce the computational cost of time-domain acoustic-wave equation numerical modeling by solving the wave equation on a coarse mesh based on the multiscale finite-element theory. In contrast to existing multiscale finite-element methods that use only first-order multiscale basis functions, our new method constructs high-order multiscale basis functions from local elliptic problems which are closely related to the Gauss-Lobatto-Legendre quadrature points in a coarse element. Essentially, these basis functions are not only determined by the order of Legendre polynomials, but also by local medium properties, and therefore can effectively convey the fine-scale information to the coarse-scale solution with high-order accuracy. Numerical tests show that our method can significantly reduce the computation time while maintain high accuracy for wave equation modeling in highly heterogeneous media by solving the corresponding discrete system only on the coarse mesh with the new high-order multiscale basis functions.

A high-order multiscale finite-element method for time-domain acoustic-wave modeling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gao, Kai; Fu, Shubin; Chung, Eric T.

Accurate and efficient wave equation modeling is vital for many applications in such as acoustics, electromagnetics, and seismology. However, solving the wave equation in large-scale and highly heterogeneous models is usually computationally expensive because the computational cost is directly proportional to the number of grids in the model. We develop a novel high-order multiscale finite-element method to reduce the computational cost of time-domain acoustic-wave equation numerical modeling by solving the wave equation on a coarse mesh based on the multiscale finite-element theory. In contrast to existing multiscale finite-element methods that use only first-order multiscale basis functions, our new method constructsmore » high-order multiscale basis functions from local elliptic problems which are closely related to the Gauss–Lobatto–Legendre quadrature points in a coarse element. Essentially, these basis functions are not only determined by the order of Legendre polynomials, but also by local medium properties, and therefore can effectively convey the fine-scale information to the coarse-scale solution with high-order accuracy. Numerical tests show that our method can significantly reduce the computation time while maintain high accuracy for wave equation modeling in highly heterogeneous media by solving the corresponding discrete system only on the coarse mesh with the new high-order multiscale basis functions.« less

Pose measurement method and experiments for high-speed rolling targets in a wind tunnel.

PubMed

Jia, Zhenyuan; Ma, Xin; Liu, Wei; Lu, Wenbo; Li, Xiao; Chen, Ling; Wang, Zhengqu; Cui, Xiaochun

2014-12-12

High-precision wind tunnel simulation tests play an important role in aircraft design and manufacture. In this study, a high-speed pose vision measurement method is proposed for high-speed and rolling targets in a supersonic wind tunnel. To obtain images with high signal-to-noise ratio and avoid impacts on the aerodynamic shape of the rolling targets, a high-speed image acquisition method based on ultrathin retro-reflection markers is presented. Since markers are small-sized and some of them may be lost when the target is rolling, a novel markers layout with which markers are distributed evenly on the surface is proposed based on a spatial coding method to achieve highly accurate pose information. Additionally, a pose acquisition is carried out according to the mentioned markers layout after removing mismatching points by Case Deletion Diagnostics. Finally, experiments on measuring the pose parameters of high-speed targets in the laboratory and in a supersonic wind tunnel are conducted to verify the feasibility and effectiveness of the proposed method. Experimental results indicate that the position measurement precision is less than 0.16 mm, the pitching and yaw angle precision less than 0.132° and the roll angle precision 0.712°.

A high-order multiscale finite-element method for time-domain acoustic-wave modeling

DOE PAGES

Gao, Kai; Fu, Shubin; Chung, Eric T.

2018-02-04

Accurate and efficient wave equation modeling is vital for many applications in such as acoustics, electromagnetics, and seismology. However, solving the wave equation in large-scale and highly heterogeneous models is usually computationally expensive because the computational cost is directly proportional to the number of grids in the model. We develop a novel high-order multiscale finite-element method to reduce the computational cost of time-domain acoustic-wave equation numerical modeling by solving the wave equation on a coarse mesh based on the multiscale finite-element theory. In contrast to existing multiscale finite-element methods that use only first-order multiscale basis functions, our new method constructsmore » high-order multiscale basis functions from local elliptic problems which are closely related to the Gauss–Lobatto–Legendre quadrature points in a coarse element. Essentially, these basis functions are not only determined by the order of Legendre polynomials, but also by local medium properties, and therefore can effectively convey the fine-scale information to the coarse-scale solution with high-order accuracy. Numerical tests show that our method can significantly reduce the computation time while maintain high accuracy for wave equation modeling in highly heterogeneous media by solving the corresponding discrete system only on the coarse mesh with the new high-order multiscale basis functions.« less

Pose Measurement Method and Experiments for High-Speed Rolling Targets in a Wind Tunnel

PubMed Central

Jia, Zhenyuan; Ma, Xin; Liu, Wei; Lu, Wenbo; Li, Xiao; Chen, Ling; Wang, Zhengqu; Cui, Xiaochun

2014-01-01

High-precision wind tunnel simulation tests play an important role in aircraft design and manufacture. In this study, a high-speed pose vision measurement method is proposed for high-speed and rolling targets in a supersonic wind tunnel. To obtain images with high signal-to-noise ratio and avoid impacts on the aerodynamic shape of the rolling targets, a high-speed image acquisition method based on ultrathin retro-reflection markers is presented. Since markers are small-sized and some of them may be lost when the target is rolling, a novel markers layout with which markers are distributed evenly on the surface is proposed based on a spatial coding method to achieve highly accurate pose information. Additionally, a pose acquisition is carried out according to the mentioned markers layout after removing mismatching points by Case Deletion Diagnostics. Finally, experiments on measuring the pose parameters of high-speed targets in the laboratory and in a supersonic wind tunnel are conducted to verify the feasibility and effectiveness of the proposed method. Experimental results indicate that the position measurement precision is less than 0.16 mm, the pitching and yaw angle precision less than 0.132° and the roll angle precision 0.712°. PMID:25615732

A proven and highly cost-effective method of early detection of breast cancer for developing countries.

PubMed

Rebentisch, D P; Rebentisch, H D; Thomas, K; Karat, S; Jadhav, A J

1995-12-01

Carcinoma of the breast is the third most common cancer in Indian women. With rapid industrialization and effective control of communicable diseases, better diagnostic and treatment facilities, cancer is emerging as a major health problem. Since early detection is the only way to reduce morbidity and mortality from breast cancer, we undertook a pilot project to evaluate efficacy of using existing manpower and resources for screening women in the high risk group. Methodology pros and cons, results, and recommendations are presented. Our method can be adopted by any developing country interested in a screening programme for malignant disease.

Laser-heat puncturing as highly effective method of post-tuberculous cystalgia treatment

NASA Astrophysics Data System (ADS)

Koultchavenia, Ekaterina V.

1999-07-01

The tuberculosis of an urine bladder in men develops is authentic less often, and recovery is authentic more often, than in the women. In 39,1 percent of the women with nephrotuberculosis and urocystis and urocystis tuberculosis a specific cystitides is finished in development of post- tuberculous cystalgia. One of starting mechanism of dysuria after the transferred urocystis tuberculosis in the women in menopause is hormonal insufficiency. The method of laser heat puncturing, developed by us, for the treatment this complication is highly effective, does not require additional introduction of medicines, can be executed as in hospitals, and in our-patient.

Fast generation of spin-squeezed states in bosonic Josephson junctions

NASA Astrophysics Data System (ADS)

Juliá-Díaz, B.; Torrontegui, E.; Martorell, J.; Muga, J. G.; Polls, A.

2012-12-01

We describe methods for the fast production of highly coherent-spin-squeezed many-body states in bosonic Josephson junctions. We start from the known mapping of the two-site Bose-Hubbard (BH) Hamiltonian to that of a single effective particle evolving according to a Schrödinger-like equation in Fock space. Since, for repulsive interactions, the effective potential in Fock space is nearly parabolic, we extend recently derived protocols for shortcuts to adiabatic evolution in harmonic potentials to the many-body BH Hamiltonian. A comparison with current experiments shows that our methods allow for an important reduction in the preparation times of highly squeezed spin states.

Using risk elasticity to prioritize risk reduction strategies for geographical areas and industry sectors.

PubMed

Li, Pei-Chiun; Ma, Hwong-Wen

2016-01-25

The total quantity of chemical emissions does not take into account their chemical toxicity, and fails to be an accurate indicator of the potential impact on human health. The sources of released contaminants, and therefore, the potential risk, also differ based on geography. Because of the complexity of the risk, there is no integrated method to evaluate the effectiveness of risk reduction. Therefore, this study developed a method to incorporate the spatial variability of emissions into human health risk assessment to evaluate how to effectively reduce risk using risk elasticity analysis. Risk elasticity analysis, the percentage change in risk in response to the percentage change in emissions, was adopted in this study to evaluate the effectiveness and efficiency of risk reduction. The results show that the main industry sectors are different in each area, and that high emission in an area does not correspond to high risk. Decreasing the high emissions of certain sectors in an area does not result in efficient risk reduction in this area. This method can provide more holistic information for risk management, prevent the development of increased risk, and prioritize the risk reduction strategies. Copyright © 2015 Elsevier B.V. All rights reserved.

Nitrogen-doped micropore-dominant carbon derived from waste pine cone as a promising metal-free electrocatalyst for aqueous zinc/air batteries

NASA Astrophysics Data System (ADS)

Lei, Xiaoke; Wang, Mengran; Lai, Yanqing; Hu, Langtao; Wang, Hao; Fang, Zhao; Li, Jie; Fang, Jing

2017-10-01

The exploitation for highly effective and low-cost metal-free catalysts with facile and environmental friendly method for oxygen reduction reaction is still a great challenge. To find an effective method for catalyst synthesis, in this manuscript, waste biomass pine cone is employed as raw material and nitrogen-doped micropore-dominant carbon material with excellent ORR catalytic activity is successfully synthesized. The as-prepared N-doped micropore-dominant carbon possesses a high surface area of 1556 m2 g-1. In addition, this carbon electrocatalyst loaded electrode exhibits a high discharge voltage 1.07 V at the current density of 50 mA cm-2, which can be ascribed to the rich micropores and high content of pyridinic N of the prepared carbon, indicative of great potential in the application of zinc/air batteries.

Application of supercritical fluid carbon dioxide to the extraction and analysis of lipids.

PubMed

Lee, Jae Won; Fukusaki, Eiichiro; Bamba, Takeshi

2012-10-01

Supercritical carbon dioxide (SCCO(2)) is an ecofriendly supercritical fluid that is chemically inert, nontoxic, noninflammable and nonpolluting. As a green material, SCCO(2) has desirable properties such as high density, low viscosity and high diffusivity that make it suitable for use as a solvent in supercritical fluid extraction, an effective and environment-friendly analytical method, and as a mobile phase for supercritical fluid chromatography, which facilitates high-throughput, high-resolution analysis. Furthermore, the low polarity of SCCO(2) is suitable for the extraction and analysis of hydrophobic compounds. The growing concern surrounding environmental pollution has triggered the development of green analysis methods based on the use of SCCO(2) in various laboratories and industries. SCCO(2) is becoming an effective alternative to conventional organic solvents. In this review, the usefulness of SCCO(2) in supercritical fluid extraction and supercritical fluid chromatography for the extraction and analysis of lipids is described.

Mild-temperature thermochemical pretreatment of green macroalgal biomass: Effects on solubilization, methanation, and microbial community structure.

PubMed

Jung, Heejung; Baek, Gahyun; Kim, Jaai; Shin, Seung Gu; Lee, Changsoo

2016-01-01

The effects of mild-temperature thermochemical pretreatments with HCl or NaOH on the solubilization and biomethanation of Ulva biomass were assessed. Within the explored region (0-0.2M HCl/NaOH, 60-90°C), both methods were effective for solubilization (about 2-fold increase in the proportion of soluble organics), particularly under high-temperature and high-chemical-dose conditions. However, increased solubilization was not translated into enhanced biogas production for both methods. Response surface analysis statistically revealed that HCl or NaOH addition enhances the solubilization degree while adversely affects the methanation. The thermal-only treatment at the upper-limit temperature (90°C) was estimated to maximize the biogas production for both methods, suggesting limited potential of HCl/NaOH treatment for enhanced Ulva biomethanation. Compared to HCl, NaOH had much stronger positive and negative effects on the solubilization and methanation, respectively. Methanosaeta was likely the dominant methanogen group in all trials. Bacterial community structure varied among the trials according primarily to HCl/NaOH addition. Copyright © 2015 Elsevier Ltd. All rights reserved.

Crocin loaded nano-emulsions: Factors affecting emulsion properties in spontaneous emulsification.

PubMed

Mehrnia, Mohammad-Amin; Jafari, Seid-Mahdi; Makhmal-Zadeh, Behzad S; Maghsoudlou, Yahya

2016-03-01

Spontaneous emulsification may be used for encapsulating bioactive compounds in food and pharmaceutical industry. It has several advantages over high energy and other low energy methods including, protecting sensitive compounds against severe conditions of high energy method and its ability to minimize surfactant, removal of cosurfactant and thermal stability compared with other low energy methods. In this study, we examined possibility of encapsulating highly soluble crocin in W/O micro-emulsions using spontaneous method which further could be used for making double emulsions. Nonionic surfactants of Span 80 and polyglycerol polyricinoleate (PGPR) were used for making micro-emulsions that showed the high potential of PGPR for spontaneous method. Surfactant to water ratio (SWR%) was evaluated to find the highest amount of aqueous phase which can be dispersed in organic phase. Droplet size decreased by increasing SWR toward the SWR=100% which had the smallest droplet size and then increased at higher levels of surfactant. By increasing SWR, shear viscosity increased which showed the high effect of PGPR on rheological properties. This study shows in addition to W/O micro-emulsions, spontaneous method could be used for preparing stable O/W micro-emulsions. Copyright © 2015 Elsevier B.V. All rights reserved.

Air-assisted liquid-liquid microextraction integrated with QuEChERS for determining endocrine-disrupting compounds in fish by high-performance liquid chromatography-tandem mass spectrometry.

PubMed

Luo, Zhoufei; Lu, Jing; Li, Haipu; Tu, Yi; Wan, Yuehao; Yang, Zhaoguang

2018-09-15

A new, sensitive, and rapid method based on the Quick, Easy, Cheap, Effective, Rugged and Safe (QuEChERS) approach and air-assisted liquid-liquid microextraction (AALLME) technology was developed for the determination of 20 endocrine-disrupting compounds (EDCs) in fish by high-performance liquid chromatography-tandem mass spectrometry. The method first integrates AALLME into QuEChERS to achieve clean-up and enrichment of the EDCs in one step. A self-made glass tube was enfolded with plasticine to withstand the high centrifugal force. The established method was developed by optimization of the parameters. High linearities (R 2  > 0.9924) and recoveries (78.2-118.6%) at three spiked levels (5, 10, and 20 ng g -1 ), and low relative standard deviation values (1.1-14.5%) and limits of detection (0.03-0.80 ng g -1 ) were obtained. The method comparison shows that the proposed method is superior as it involves less organic solvent usage, simple operation and high efficiency. This method was successfully applied to different fishes for analyzing EDCs. Copyright © 2018 Elsevier Ltd. All rights reserved.

Is traditional contraceptive use in Moldova associated with poverty and isolation?

PubMed

Lyons-Amos, Mark J; Durrant, Gabriele B; Padmadas, Sabu S

2011-05-01

This study investigates the correlates of traditional contraceptive use in Moldova, a poor country in Europe with one of the highest proportions of traditional contraceptive method users. The high reliance on traditional methods, particularly in the context of sub-replacement level fertility rate, has not been systematically evaluated in demographic research. Using cross-sectional data on a sub-sample of 6039 sexually experienced women from the 2005 Moldovan Demographic and Health Survey, this study hypothesizes that (a) economic and spatial disadvantages increase the likelihood of traditional method use, and (b) high exposure to family planning/reproductive health (FP/RH) programmes increases the propensity to modern method use. Multilevel multinomial models are used to examine the correlates of traditional method use controlling for exposure to sexual activity, socioeconomic and demographic characteristics and data structure. The results show that economic disadvantage increases the probability of traditional method use, but the overall effect is small. Although higher family planning media exposure decreases the reliance on traditional methods among younger women, it has only a marginal effect in increasing modern method use among older women. Family planning programmes designed to encourage women to switch from traditional to modern methods have some success--although the effect is considerably reduced in regions outside of the capital Chisinau. The study concludes that FP/RH efforts directed towards the poorest may have limited impact, but interventions targeted at older women could reduce the burden of unwanted pregnancies and abortions. Addressing differentials in accessing modern methods could improve uptake in rural areas.

Analysis and feasibility of asphalt pavement performance-based specifications for WisDOT.

DOT National Transportation Integrated Search

2016-12-25

Literature review of most recent methods used for effective characterization of asphalt mixtures resulted in selecting aset of test methods for measuring mixture resistance for rutting and moisture damage at high temperature, fatigue cracking at inte...

Common Effects Methodology for Pesticides

EPA Pesticide Factsheets

EPA is exploring how to build on the substantial high quality science developed under both OPP programs to develop additional tools and approaches to support a consistent and common set of effects characterization methods using best available information.

A high-order multi-zone cut-stencil method for numerical simulations of high-speed flows over complex geometries

NASA Astrophysics Data System (ADS)

Greene, Patrick T.; Eldredge, Jeff D.; Zhong, Xiaolin; Kim, John

2016-07-01

In this paper, we present a method for performing uniformly high-order direct numerical simulations of high-speed flows over arbitrary geometries. The method was developed with the goal of simulating and studying the effects of complex isolated roughness elements on the stability of hypersonic boundary layers. The simulations are carried out on Cartesian grids with the geometries imposed by a third-order cut-stencil method. A fifth-order hybrid weighted essentially non-oscillatory scheme was implemented to capture any steep gradients in the flow created by the geometries and a third-order Runge-Kutta method is used for time advancement. A multi-zone refinement method was also utilized to provide extra resolution at locations with expected complex physics. The combination results in a globally fourth-order scheme in space and third order in time. Results confirming the method's high order of convergence are shown. Two-dimensional and three-dimensional test cases are presented and show good agreement with previous results. A simulation of Mach 3 flow over the logo of the Ubuntu Linux distribution is shown to demonstrate the method's capabilities for handling complex geometries. Results for Mach 6 wall-bounded flow over a three-dimensional cylindrical roughness element are also presented. The results demonstrate that the method is a promising tool for the study of hypersonic roughness-induced transition.

Synthetic carbohydrate research based on organic electrochemistry.

PubMed

Nokami, Toshiki; Saito, Kodai; Yoshida, Jun-Ichi

2012-12-01

Development of a novel method for generating glycosyl cations or their equivalents is highly desired, because such intermediates are crucial for developing stereoselective glycosylations in oligosaccharide syntheses. In this review we focus on electrochemical methods that we have recently developed. The anodic oxidation of thioglycosides is effective for generating glycosyl triflate pools, which react with glycosyl acceptors. The reaction of glycosyl triflate pools with diorganosulfides gives glycosyl sulfonium ions, which also serve as effective glycosylation intermediates. The indirect electrochemical method is effective for the generation of glycosyl cations or their equivalents and the use of a flow-microreactor system enables glycosylation using such intermediates. Copyright © 2012 Elsevier Ltd. All rights reserved.

Effective description of a 3D object for photon transportation in Monte Carlo simulation

NASA Astrophysics Data System (ADS)

Suganuma, R.; Ogawa, K.

2000-06-01

Photon transport simulation by means of the Monte Carlo method is an indispensable technique for examining scatter and absorption correction methods in SPECT and PET. The authors have developed a method for object description with maximum size regions (maximum rectangular regions: MRRs) to speed up photon transport simulation, and compared the computation time with that for conventional object description methods, a voxel-based (VB) method and an octree method, in the simulations of two kinds of phantoms. The simulation results showed that the computation time with the proposed method became about 50% of that with the VD method and about 70% of that with the octree method for a high resolution MCAT phantom. Here, details of the expansion of the MRR method to three dimensions are given. Moreover, the effectiveness of the proposed method was compared with the VB and octree methods.

Analysis of laser pumping and thermal effects based on element analysis

NASA Astrophysics Data System (ADS)

Cui, Li; Liu, Zhijia; Zhang, Yizhuo; Han, Juan

2018-03-01

Thermal effect is a plateau that limits the output of high-power, high beam quality laser, and thermal effects become worse with the increase of pump power. We can reduce the effects caused by thermal effects from pumping, laser medium shape, cooling method and other aspects. In this article, by using finite element analysis software, the thermal effects between Nd:Glass and Nd:YAG laser crystal was analyzed and compared. The causes of generation for thermal effects, and factors that influence the distribution in laser medium were analyzed, including the light source, the laser medium shape and the working mode. Nd:Glass is more suitable for low repetition frequency, high energy pulsed laser output, due to its large size, line width and so on, and Nd:YAG is more suitable for continue or high repetition rate laser output, due to its higher thermal conductivity.

The Positive Effect of Resilience on Stress and Business Outcomes in Difficult Work Environments

PubMed Central

Shatté, Andrew; Perlman, Adam; Smith, Brad; Lynch, Wendy D.

2017-01-01

Objective: To examine whether resilience has a protective effect in difficult work environments. Methods: A survey of 2063 individuals measured individual resilience, stress, burnout, sleep problems, likelihood of depression, job satisfaction, intent to quit, absences, and productivity. It also measured work characteristics: job demands, job influence, and social support. Multivariate and logistic regression models examined the main effects and interactions of resilience and job characteristics. Results: High strain work environments (high demand, low influence, and low support) have an unfavorable effect on all outcomes. Resilience has a protective effect on all outcomes. For stress, burnout, and sleep, higher resilience has a more protective effect under low-strain conditions. For depression, absence and productivity, resilience has a more protective effect when job strain is high. Conclusions: Workers with high resilience have better outcomes in difficult work environments. PMID:28002352

High-efficient and high-content cytotoxic recording via dynamic and continuous cell-based impedance biosensor technology.

PubMed

Hu, Ning; Fang, Jiaru; Zou, Ling; Wan, Hao; Pan, Yuxiang; Su, Kaiqi; Zhang, Xi; Wang, Ping

2016-10-01

Cell-based bioassays were effective method to assess the compound toxicity by cell viability, and the traditional label-based methods missed much information of cell growth due to endpoint detection, while the higher throughputs were demanded to obtain dynamic information. Cell-based biosensor methods can dynamically and continuously monitor with cell viability, however, the dynamic information was often ignored or seldom utilized in the toxin and drug assessment. Here, we reported a high-efficient and high-content cytotoxic recording method via dynamic and continuous cell-based impedance biosensor technology. The dynamic cell viability, inhibition ratio and growth rate were derived from the dynamic response curves from the cell-based impedance biosensor. The results showed that the biosensors has the dose-dependent manners to diarrhetic shellfish toxin, okadiac acid based on the analysis of the dynamic cell viability and cell growth status. Moreover, the throughputs of dynamic cytotoxicity were compared between cell-based biosensor methods and label-based endpoint methods. This cell-based impedance biosensor can provide a flexible, cost and label-efficient platform of cell viability assessment in the shellfish toxin screening fields.

Matrix form of Legendre polynomials for solving linear integro-differential equations of high order

NASA Astrophysics Data System (ADS)

Kammuji, M.; Eshkuvatov, Z. K.; Yunus, Arif A. M.

2017-04-01

This paper presents an effective approximate solution of high order of Fredholm-Volterra integro-differential equations (FVIDEs) with boundary condition. Legendre truncated series is used as a basis functions to estimate the unknown function. Matrix operation of Legendre polynomials is used to transform FVIDEs with boundary conditions into matrix equation of Fredholm-Volterra type. Gauss Legendre quadrature formula and collocation method are applied to transfer the matrix equation into system of linear algebraic equations. The latter equation is solved by Gauss elimination method. The accuracy and validity of this method are discussed by solving two numerical examples and comparisons with wavelet and methods.

Improving Cardiac Action Potential Measurements: 2D and 3D Cell Culture.

PubMed

Daily, Neil J; Yin, Yue; Kemanli, Pinar; Ip, Brian; Wakatsuki, Tetsuro

2015-11-01

Progress in the development of assays for measuring cardiac action potential is crucial for the discovery of drugs for treating cardiac disease and assessing cardiotoxicity. Recently, high-throughput methods for assessing action potential using induced pluripotent stem cell (iPSC) derived cardiomyocytes in both two-dimensional monolayer cultures and three-dimensional tissues have been developed. We describe an improved method for assessing cardiac action potential using an ultra-fast cost-effective plate reader with commercially available dyes. Our methods improve dramatically the detection of the fluorescence signal from these dyes and make way for the development of more high-throughput methods for cardiac drug discovery and cardiotoxicity.

Noise suppressed partial volume correction for cardiac SPECT/CT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chan, Chung; Liu, Chi, E-mail: chi.liu@yale.edu

Purpose: Partial volume correction (PVC) methods typically improve quantification at the expense of increased image noise and reduced reproducibility. In this study, the authors developed a novel voxel-based PVC method that incorporates anatomical knowledge to improve quantification while suppressing noise for cardiac SPECT/CT imaging. Methods: In the proposed method, the SPECT images were first reconstructed using anatomical-based maximum a posteriori (AMAP) with Bowsher’s prior to penalize noise while preserving boundaries. A sequential voxel-by-voxel PVC approach (Yang’s method) was then applied on the AMAP reconstruction using a template response. This template response was obtained by forward projecting a template derived frommore » a contrast-enhanced CT image, and then reconstructed using AMAP to model the partial volume effects (PVEs) introduced by both the system resolution and the smoothing applied during reconstruction. To evaluate the proposed noise suppressed PVC (NS-PVC), the authors first simulated two types of cardiac SPECT studies: a {sup 99m}Tc-tetrofosmin myocardial perfusion scan and a {sup 99m}Tc-labeled red blood cell (RBC) scan on a dedicated cardiac multiple pinhole SPECT/CT at both high and low count levels. The authors then applied the proposed method on a canine equilibrium blood pool study following injection with {sup 99m}Tc-RBCs at different count levels by rebinning the list-mode data into shorter acquisitions. The proposed method was compared to MLEM reconstruction without PVC, two conventional PVC methods, including Yang’s method and multitarget correction (MTC) applied on the MLEM reconstruction, and AMAP reconstruction without PVC. Results: The results showed that the Yang’s method improved quantification, however, yielded increased noise and reduced reproducibility in the regions with higher activity. MTC corrected for PVE on high count data with amplified noise, although yielded the worst performance among all the methods tested on low-count data. AMAP effectively suppressed noise and reduced the spill-in effect in the low activity regions. However it was unable to reduce the spill-out effect in high activity regions. NS-PVC yielded superior performance in terms of both quantitative assessment and visual image quality while improving reproducibility. Conclusions: The results suggest that NS-PVC may be a promising PVC algorithm for application in low-dose protocols, and in gated and dynamic cardiac studies with low counts.« less

Creating high yield water soluble luminescent graphene quantum dots via exfoliating and disintegrating carbon nanotubes and graphite flakes.

PubMed

Lin, Liangxu; Zhang, Shaowei

2012-10-21

We have developed an effective method to exfoliate and disintegrate multi-walled carbon nanotubes and graphite flakes. With this technique, high yield production of luminescent graphene quantum dots with high quantum yield and low oxidization can be achieved.

EVALUATION OF THE HIGH VOLUME COLLECTION SYSTEM (HVCS) FOR QUANTIFYING FUGITIVE ORGANIC VAPOR LEAKS

EPA Science Inventory

The report discusses a recently developed measurements technique that offers the potential for providing an easy-to-use and cost effective means to directly measure organic vapor leaks. The method, called High Volume Collection System (HVCS), uses a high volume sampling device an...

Mass Media Strategies Targeting High Sensation Seekers: What Works and Why

ERIC Educational Resources Information Center

Stephenson, Michael T.

2003-01-01

Objectives: To examine strategies for using the mass media effectively in drug prevention campaigns targeting high sensation seekers. Methods: Both experimental lab and field studies were used to develop a comprehensive audience segmentation strategy targeting high sensation seekers. Results: A 4-pronged targeting strategy employed in an…

Cyber High School Students' Transition to a Traditional University

ERIC Educational Resources Information Center

Gracey, Dorothy M.

2010-01-01

This mixed-method study identifies cyber high school graduates' perceptions of the effect of a cyber high school education on successful transition to a traditional university. The study examined students' perceptions of the advantages and disadvantages their cyber education experience contributed to their academic and social transition to…

Cultivating the Academic Integrity of Urban Adolescents with Ethical Philosophy Programming

ERIC Educational Resources Information Center

Seider, Scott; Novick, Sarah; Gomez, Jessica

2013-01-01

This mixed-methods study considered the effects of ethical philosophy programming at a high-performing, high-poverty urban high school upon the academic integrity of participating adolescents ("n" = 279). Analyses of pre-post survey data revealed that participating adolescents reported significantly higher levels of academic integrity…

Potential climate engineering effectiveness and side effects during a high carbon dioxide-emission scenario

PubMed Central

Keller, David P.; Feng, Ellias Y.; Oschlies, Andreas

2014-01-01

The realization that mitigation efforts to reduce carbon dioxide emissions have, until now, been relatively ineffective has led to an increasing interest in climate engineering as a possible means of preventing the potentially catastrophic consequences of climate change. While many studies have addressed the potential effectiveness of individual methods there have been few attempts to compare them. Here we use an Earth system model to compare the effectiveness and side effects of afforestation, artificial ocean upwelling, ocean iron fertilization, ocean alkalinization and solar radiation management during a high carbon dioxide-emission scenario. We find that even when applied continuously and at scales as large as currently deemed possible, all methods are, individually, either relatively ineffective with limited (<8%) warming reductions, or they have potentially severe side effects and cannot be stopped without causing rapid climate change. Our simulations suggest that the potential for these types of climate engineering to make up for failed mitigation may be very limited. PMID:24569320

High-frequency ultrasonic methods for determining corrosion layer thickness of hollow metallic components.

PubMed

Liu, Hongwei; Zhang, Lei; Liu, Hong Fei; Chen, Shuting; Wang, Shihua; Wong, Zheng Zheng; Yao, Kui

2018-05-16

Corrosion in internal cavity is one of the most common problems occurs in many hollow metallic components, such as pipes containing corrosive fluids and high temperature turbines in aircraft. It is highly demanded to non-destructively detect the corrosion inside hollow components and determine the corrosion extent from the external side. In this work, we present two high-frequency ultrasonic non-destructive testing (NDT) technologies, including piezoelectric pulse-echo and laser-ultrasonic methods, for detecting corrosion of Ni superalloy from the opposite side. The determination of corrosion layer thickness below ∼100 µm has been demonstrated by both methods, in comparison with X-CT and SEM. With electron microscopic examination, it is found that with multilayer corrosion structure formed over a prolonged corrosion time, the ultrasonic NDT methods can only reliably reveal outer corrosion layer thickness because of the resulting acoustic contrast among the multiple layers due to their respective different mechanical parameters. A time-frequency signal analysis algorithm is employed to effectively enhance the high frequency ultrasonic signal contrast for the piezoelectric pulse-echo method. Finally, a blind test on a Ni superalloy turbine blade with internal corrosion is conducted with the high frequency piezoelectric pulser-receiver method. Copyright © 2018 Elsevier B.V. All rights reserved.

Adolescent contraception: review and guidance for pediatric clinicians.

PubMed

Potter, J; Santelli, J S

2015-02-01

The majority of adolescents initiate sexual activity during their teenage years, making contraception an important aspect of routine adolescent health care. Despite common misperceptions, all available methods of reversible contraception are appropriate for adolescent use. Contraceptive side effects profiles and barriers to use of certain methods should be considered when providing contraceptives to adolescents. In particular, ease of use, confidentiality, and menstrual effects are main concerns of adolescents. Contraceptive counseling with adolescents should describe method efficacy, discuss user preferences, explore barriers to use, counsel regarding sexually transmitted infection prevention, and consider what to do if contraception fails. Emergency contraception should be widely discussed with adolescents, as it is appropriate for use during gaps in other contraceptive use, method failure, and adolescents who are not using another form of contraception. Dual method use (condom plus a highly effective method of contraception) is the gold standard for prevention of both pregnancy and sexually transmitted infections.

Uncertainty of quantitative microbiological methods of pharmaceutical analysis.

PubMed

Gunar, O V; Sakhno, N G

2015-12-30

The total uncertainty of quantitative microbiological methods, used in pharmaceutical analysis, consists of several components. The analysis of the most important sources of the quantitative microbiological methods variability demonstrated no effect of culture media and plate-count techniques in the estimation of microbial count while the highly significant effect of other factors (type of microorganism, pharmaceutical product and individual reading and interpreting errors) was established. The most appropriate method of statistical analysis of such data was ANOVA which enabled not only the effect of individual factors to be estimated but also their interactions. Considering all the elements of uncertainty and combining them mathematically the combined relative uncertainty of the test results was estimated both for method of quantitative examination of non-sterile pharmaceuticals and microbial count technique without any product. These data did not exceed 35%, appropriated for a traditional plate count methods. Copyright © 2015 Elsevier B.V. All rights reserved.

Remote sensing of Sonoran Desert vegetation structure and phenology with ground-based LiDAR

USGS Publications Warehouse

Sankey, Joel B.; Munson, Seth M.; Webb, Robert H.; Wallace, Cynthia S.A.; Duran, Cesar M.

2015-01-01

Long-term vegetation monitoring efforts have become increasingly important for understanding ecosystem response to global change. Many traditional methods for monitoring can be infrequent and limited in scope. Ground-based LiDAR is one remote sensing method that offers a clear advancement to monitor vegetation dynamics at high spatial and temporal resolution. We determined the effectiveness of LiDAR to detect intra-annual variability in vegetation structure at a long-term Sonoran Desert monitoring plot dominated by cacti, deciduous and evergreen shrubs. Monthly repeat LiDAR scans of perennial plant canopies over the course of one year had high precision. LiDAR measurements of canopy height and area were accurate with respect to total station survey measurements of individual plants. We found an increase in the number of LiDAR vegetation returns following the wet North American Monsoon season. This intra-annual variability in vegetation structure detected by LiDAR was attributable to a drought deciduous shrub Ambrosia deltoidea, whereas the evergreen shrub Larrea tridentata and cactus Opuntia engelmannii had low variability. Benefits of using LiDAR over traditional methods to census desert plants are more rapid, consistent, and cost-effective data acquisition in a high-resolution, 3-dimensional context. We conclude that repeat LiDAR measurements can be an effective method for documenting ecosystem response to desert climatology and drought over short time intervals and at detailed-local spatial scale.

Hot issues in female and male hormonal contraception.

PubMed

Gava, Giulia; Lantadilla, Claudia; Martelli, Valentina; Fattorini, Anna; Seracchioli, Renato; Meriggiola, Maria C

2016-02-01

In recent years a number of significant developments in the field of female hormonal contraception have been made which have produced new formulations and delivery systems providing high efficacy, safety and important non-contraceptive benefits. In particular long-acting reversible contraception (LARC) formulations have been demonstrated to ensure extremely high efficacy in typical use, minimal contraindications, optimal safety in all women thereby representing the best option for most women of all ages. Their effectiveness is not reliant upon user adherence and their ability to reduce unintended pregnancies and abortions has been proven. Unfortunately the same considerations cannot be made for male hormonal contraception. Although a large number of men are interested and would welcome the opportunity to use male contraceptive methods, no safe, effective and reversible methods are available on the market. Current methods available for men are limited to condoms and vasectomy. Highly effective prototype regimens have been developed but the pharmaceutical industry is unwilling to pursue further development and market these products. Of all new approaches to male contraception, hormonal methods are the closest to clinical application. These are based on the reversible suppression of luteinizing hormone and follicle stimulating hormone with subsequent reversible inhibition of spermatogenesis and consequent replacement to maintain androgen dependent physiological functions. Most approaches tested combination regimens such as testosterone and a progestin or testosterone and a GnRH analog.

Evaluation of positively charged alumina nanofibre cartridge filters for the primary concentration of noroviruses, adenoviruses and male-specific coliphages from seawater.

PubMed

Gibbons, C D; Rodríguez, R A; Tallon, L; Sobsey, M D

2010-08-01

To evaluate the electropositive, alumina nanofibre (NanoCeram) cartridge filter as a primary concentration method for recovering adenovirus, norovirus and male-specific coliphages from natural seawater. Viruses were concentrated from 40 l of natural seawater using a NanoCeram cartridge filter and eluted from the filter either by soaking the filter in eluent or by recirculating the eluent continuously through the filter using a peristaltic pump. The elution solution consisted of 3% beef extract and 0.1 mol l(-1) of glycine. The method using a peristaltic pump was more effective in removing the viruses from the filter. High recoveries of norovirus and male-specific coliphages (>96%) but not adenovirus (<3%) were observed from seawater. High adsorption to the filter was observed for adenovirus and male-specific coliphages (>98%). The adsorption and recovery of adenovirus and male-specific coliphages were also determined for fresh finished water and source water. The NanoCeram cartridge filter was an effective primary concentration method for the concentration of norovirus and male-specific coliphages from natural seawater, but not for adenovirus, in spite of the high adsorption of adenovirus to the filter. This study demonstrates that NanoCeram cartridge filter is an effective primary method for concentrating noroviruses and male-specific coliphages from seawater, thereby simplifying collection and processing of water samples for virus recovery.

Multi-exposure high dynamic range image synthesis with camera shake correction

NASA Astrophysics Data System (ADS)

Li, Xudong; Chen, Yongfu; Jiang, Hongzhi; Zhao, Huijie

2017-10-01

Machine vision plays an important part in industrial online inspection. Owing to the nonuniform illuminance conditions and variable working distances, the captured image tends to be over-exposed or under-exposed. As a result, when processing the image such as crack inspection, the algorithm complexity and computing time increase. Multiexposure high dynamic range (HDR) image synthesis is used to improve the quality of the captured image, whose dynamic range is limited. Inevitably, camera shake will result in ghost effect, which blurs the synthesis image to some extent. However, existed exposure fusion algorithms assume that the input images are either perfectly aligned or captured in the same scene. These assumptions limit the application. At present, widely used registration based on Scale Invariant Feature Transform (SIFT) is usually time consuming. In order to rapidly obtain a high quality HDR image without ghost effect, we come up with an efficient Low Dynamic Range (LDR) images capturing approach and propose a registration method based on ORiented Brief (ORB) and histogram equalization which can eliminate the illumination differences between the LDR images. The fusion is performed after alignment. The experiment results demonstrate that the proposed method is robust to illumination changes and local geometric distortion. Comparing with other exposure fusion methods, our method is more efficient and can produce HDR images without ghost effect by registering and fusing four multi-exposure images.

A wavelet-based adaptive fusion algorithm of infrared polarization imaging

NASA Astrophysics Data System (ADS)

Yang, Wei; Gu, Guohua; Chen, Qian; Zeng, Haifang

2011-08-01

The purpose of infrared polarization image is to highlight man-made target from a complex natural background. For the infrared polarization images can significantly distinguish target from background with different features, this paper presents a wavelet-based infrared polarization image fusion algorithm. The method is mainly for image processing of high-frequency signal portion, as for the low frequency signal, the original weighted average method has been applied. High-frequency part is processed as follows: first, the source image of the high frequency information has been extracted by way of wavelet transform, then signal strength of 3*3 window area has been calculated, making the regional signal intensity ration of source image as a matching measurement. Extraction method and decision mode of the details are determined by the decision making module. Image fusion effect is closely related to the setting threshold of decision making module. Compared to the commonly used experiment way, quadratic interpolation optimization algorithm is proposed in this paper to obtain threshold. Set the endpoints and midpoint of the threshold searching interval as initial interpolation nodes, and compute the minimum quadratic interpolation function. The best threshold can be obtained by comparing the minimum quadratic interpolation function. A series of image quality evaluation results show this method has got improvement in fusion effect; moreover, it is not only effective for some individual image, but also for a large number of images.

Robust gene selection methods using weighting schemes for microarray data analysis.

PubMed

Kang, Suyeon; Song, Jongwoo

2017-09-02

A common task in microarray data analysis is to identify informative genes that are differentially expressed between two different states. Owing to the high-dimensional nature of microarray data, identification of significant genes has been essential in analyzing the data. However, the performances of many gene selection techniques are highly dependent on the experimental conditions, such as the presence of measurement error or a limited number of sample replicates. We have proposed new filter-based gene selection techniques, by applying a simple modification to significance analysis of microarrays (SAM). To prove the effectiveness of the proposed method, we considered a series of synthetic datasets with different noise levels and sample sizes along with two real datasets. The following findings were made. First, our proposed methods outperform conventional methods for all simulation set-ups. In particular, our methods are much better when the given data are noisy and sample size is small. They showed relatively robust performance regardless of noise level and sample size, whereas the performance of SAM became significantly worse as the noise level became high or sample size decreased. When sufficient sample replicates were available, SAM and our methods showed similar performance. Finally, our proposed methods are competitive with traditional methods in classification tasks for microarrays. The results of simulation study and real data analysis have demonstrated that our proposed methods are effective for detecting significant genes and classification tasks, especially when the given data are noisy or have few sample replicates. By employing weighting schemes, we can obtain robust and reliable results for microarray data analysis.

Analysis of Fiber Clustering in Composite Materials Using High-Fidelity Multiscale Micromechanics

NASA Technical Reports Server (NTRS)

Bednarcyk, Brett A.; Aboudi, Jacob; Arnold, Steven M.

2015-01-01

A new multiscale micromechanical approach is developed for the prediction of the behavior of fiber reinforced composites in presence of fiber clustering. The developed method is based on a coupled two-scale implementation of the High-Fidelity Generalized Method of Cells theory, wherein both the local and global scales are represented using this micromechanical method. Concentration tensors and effective constitutive equations are established on both scales and linked to establish the required coupling, thus providing the local fields throughout the composite as well as the global properties and effective nonlinear response. Two nondimensional parameters, in conjunction with actual composite micrographs, are used to characterize the clustering of fibers in the composite. Based on the predicted local fields, initial yield and damage envelopes are generated for various clustering parameters for a polymer matrix composite with both carbon and glass fibers. Nonlinear epoxy matrix behavior is also considered, with results in the form of effective nonlinear response curves, with varying fiber clustering and for two sets of nonlinear matrix parameters.

Energetics using the single point IMOMO (integrated molecular orbital+molecular orbital) calculations: Choices of computational levels and model system

NASA Astrophysics Data System (ADS)

Svensson, Mats; Humbel, Stéphane; Morokuma, Keiji

1996-09-01

The integrated MO+MO (IMOMO) method, recently proposed for geometry optimization, is tested for accurate single point calculations. The principle idea of the IMOMO method is to reproduce results of a high level MO calculation for a large ``real'' system by dividing it into a small ``model'' system and the rest and applying different levels of MO theory for the two parts. Test examples are the activation barrier of the SN2 reaction of Cl-+alkyl chlorides, the C=C double bond dissociation of olefins and the energy of reaction for epoxidation of benzene. The effects of basis set and method in the lower level calculation as well as the effects of the choice of model system are investigated in detail. The IMOMO method gives an approximation to the high level MO energetics on the real system, in most cases with very small errors, with a small additional cost over the low level calculation. For instance, when the MP2 (Møller-Plesset second-order perturbation) method is used as the lower level method, the IMOMO method reproduces the results of very high level MO method within 2 kcal/mol, with less than 50% of additional computer time, for the first two test examples. When the HF (Hartree-Fock) method is used as the lower level method, it is less accurate and depends more on the choice of model system, though the improvement over the HF energy is still very significant. Thus the IMOMO single point calculation provides a method for obtaining reliable local energetics such as bond energies and activation barriers for a large molecular system.

Forming high efficiency silicon solar cells using density-graded anti-reflection surfaces

DOEpatents

Yuan, Hao-Chih; Branz, Howard M.; Page, Matthew R.

2014-09-09

A method (50) is provided for processing a graded-density AR silicon surface (14) to provide effective surface passivation. The method (50) includes positioning a substrate or wafer (12) with a silicon surface (14) in a reaction or processing chamber (42). The silicon surface (14) has been processed (52) to be an AR surface with a density gradient or region of black silicon. The method (50) continues with heating (54) the chamber (42) to a high temperature for both doping and surface passivation. The method (50) includes forming (58), with a dopant-containing precursor in contact with the silicon surface (14) of the substrate (12), an emitter junction (16) proximate to the silicon surface (14) by doping the substrate (12). The method (50) further includes, while the chamber is maintained at the high or raised temperature, forming (62) a passivation layer (19) on the graded-density silicon anti-reflection surface (14).

Forming high-efficiency silicon solar cells using density-graded anti-reflection surfaces

DOEpatents

Yuan, Hao-Chih; Branz, Howard M.; Page, Matthew R.

2015-07-07

A method (50) is provided for processing a graded-density AR silicon surface (14) to provide effective surface passivation. The method (50) includes positioning a substrate or wafer (12) with a silicon surface (14) in a reaction or processing chamber (42). The silicon surface (14) has been processed (52) to be an AR surface with a density gradient or region of black silicon. The method (50) continues with heating (54) the chamber (42) to a high temperature for both doping and surface passivation. The method (50) includes forming (58), with a dopant-containing precursor in contact with the silicon surface (14) of the substrate (12), an emitter junction (16) proximate to the silicon surface (14) by doping the substrate (12). The method (50) further includes, while the chamber is maintained at the high or raised temperature, forming (62) a passivation layer (19) on the graded-density silicon anti-reflection surface (14).

An updated ciguatoxin extraction method and silica cleanup for use with HPLC-MS/MS for the analysis of P-CTX-1, PCTX-2 and P-CTX-3.

PubMed

Meyer, Lauren; Carter, Steve; Capper, Angela

2015-12-15

Ciguatera fish poisoning is a debilitating human neuro-intoxication caused by consumption of tropical marine organisms, contaminated with bioaccumulated ciguatoxins (CTXs). The growing number of cases coupled with the high toxicity of CTXs makes their reliable detection and quantification of paramount importance. Three commonly occurring ciguatoxins, P-CTX-1, 2 and 3 from five different ciguatoxic Spanish mackerel (Scomberomorus commerson), were used to assess the effectiveness of different extraction techniques: homogenization (high powered blending vs. ultrasonication); C-18 column sizes (500 mg vs. 900 mg); and a novel HILIC SPE cleanup. Despite minor differences, blending and sonication proved equally effective. Larger 900 mg columns offered a greater extraction efficiency, increasing detected P-CTX-1 by 37% (P < 0.001). The newly adapted cleanup was highly effective at reducing co-eluting phospholipids thereby reducing matrix effects and increasing detectable CTXs by HPLC-MS/MS. Silica cleanup extraction efficiencies were also compared between the highly effective and validated ciguatoxin rapid extraction method (CREM) and current best practice extraction method employed by Queensland Health (QH). Overall, the QH protocol proved more effective, especially when paired with the newly adapted cleanup, as this increased the amount of extracted P-CTX-1 by 46% (P < 0.01), P-CTX-2 by 10% and P-CTX-3 by 71% (P = 0.001). This study suggests the QH protocol utilizing a 900 mg C-18 column and newly adapted HILIC SPE cleanup was most effective at extracting P-CTX-1, -2, -3. Specifically P-CTX-1, the primary ciguatoxin congener of concern due to its extremely high potency and an ability to cause CFP at 0.1 μg/kg following consumption of carnivorous fish flesh. Despite being more time intensive (an additional 85 min per batch of 12 samples), this will be especially effective for assessing lower toxin burdens, which may be near the limit of detection. Copyright © 2015 Elsevier Ltd. All rights reserved.

An effective method of UV-oxidation of dissolved organic carbon in natural waters for radiocarbon analysis by accelerator mass spectrometry

NASA Astrophysics Data System (ADS)

Xue, Yuejun; Ge, Tiantian; Wang, Xuchen

2015-12-01

Radiocarbon (14C) measurement of dissolved organic carbon (DOC) is a very powerful tool to study the sources, transformation and cycling of carbon in the ocean. The technique, however, remains great challenges for complete and successful oxidation of sufficient DOC with low blanks for high precision carbon isotopic ratio analysis, largely due to the overwhelming proportion of salts and low DOC concentrations in the ocean. In this paper, we report an effective UV-Oxidation method for oxidizing DOC in natural waters for radiocarbon analysis by accelerator mass spectrometry (AMS). The UV-oxidation system and method show 95%±4% oxidation efficiency and high reproducibility for DOC in both river and seawater samples. The blanks associated with the method was also low (about 3 µg C) that is critical for 14C analysis. As a great advantage of the method, multiple water samples can be oxidized at the same time so it reduces the sample processing time substantially compared with other UV-oxidation method currently being used in other laboratories. We have used the system and method for 14C studies of DOC in rivers, estuaries, and oceanic environments and have received promise results.

Optimization of macropore evolution towards high photocatalytic activity enhancement in meso/macro porous Anatase TiO2

NASA Astrophysics Data System (ADS)

Nair, Radhika V.; Gayathri, P. K.; Siva Gummaluri, Venkata; Vijayan, C.

2017-01-01

We report on an optimization strategy for macro pore evolution leading to the design of highly photocatalytic 3D hierarchical meso/macroporous TiO2 via much simpler, faster and cost effective synthesis scheme. Meso/macro porous TiO2 is an excellent candidate material for photocatalytic applications owing to the availability of internal surfaces as active sites for redox reactions. The current research scenario focuses on the design of highly efficient photocatalytic systems as well as rapid, facile and cost effective methods of synthesis and optimization of parameters. The present report is on the gradual evolution of macropores in anatase TiO2 by the effective control of pH of the solvent, reaction time, temperature, solvent ratio and reactant concentration via a facile hydrothermal method in this regard. 3D hierarchical macroporous structures are obtained at pH 7 within a comparatively short reaction time of 5 h and demonstrated to be highly photocatalytic (with rate constant four times that of P25 nanoparticles) through photodegradation of Rhodamine B dye.

The fabrication of ZnO nanowire field-effect transistors by roll-transfer printing

NASA Astrophysics Data System (ADS)

Chang, Yi-Kuei; Hong, Franklin Chau-Nan

2009-05-01

A method with the potential to fabricate large-area nanowire field-effect transistors (NW-FETs) was demonstrated in this study. Using a high-speed roller (20-80 cm min-1), transfer printing was successfully employed to transfer vertically aligned zinc oxide (ZnO) nanowires grown on a donor substrate to a polydimethylsiloxane (PDMS) stamp and then print the ordered ZnO nanowire arrays on the received substrate for the fabrication of NW-FETs. ZnO NW-FETs fabricated by this method exhibit high performances with a threshold voltage of around 0.25 V, a current on/off ratio as high as 105, a subthreshold slope of 360 mV/dec, and a field-effect mobility of around 90 cm2 V-1 s-1. The excellent device characteristics suggest that the roll-transfer printing technique, which is compatible with the roll-to-roll (R2R) process and operated in atmosphere, has a good potential for the high-speed fabrication of large-area nanowire transistors for flexible devices and flat panel displays.

The fabrication of ZnO nanowire field-effect transistors by roll-transfer printing.

PubMed

Chang, Yi-Kuei; Hong, Franklin Chau-Nan

2009-05-13

A method with the potential to fabricate large-area nanowire field-effect transistors (NW-FETs) was demonstrated in this study. Using a high-speed roller (20-80 cm min(-1)), transfer printing was successfully employed to transfer vertically aligned zinc oxide (ZnO) nanowires grown on a donor substrate to a polydimethylsiloxane (PDMS) stamp and then print the ordered ZnO nanowire arrays on the received substrate for the fabrication of NW-FETs. ZnO NW-FETs fabricated by this method exhibit high performances with a threshold voltage of around 0.25 V, a current on/off ratio as high as 10(5), a subthreshold slope of 360 mV/dec, and a field-effect mobility of around 90 cm(2) V(-1) s(-1). The excellent device characteristics suggest that the roll-transfer printing technique, which is compatible with the roll-to-roll (R2R) process and operated in atmosphere, has a good potential for the high-speed fabrication of large-area nanowire transistors for flexible devices and flat panel displays.

The influence of the application of personal response systems on the effects of teaching and learning physics at the high school level

NASA Astrophysics Data System (ADS)

Binek, Sławomir; Kimla, Damian; Jarosz, Jerzy

2017-01-01

We report on the effectiveness of using interactive personal response systems in teaching physics in secondary schools. Our research were conducted over the period of 2013-2016 using the system called clickers. The idea is based on a reciprocal interaction allowing one to ask questions and receive immediate responses from all the students simultaneously. Our investigation has confirmed this method to be highly effective and powerful. In particular, students’ ability to acquire knowledge increased with the time spent using clickers. We have successfully applied the system also to entire physics courses. As a result, a positive feedback from students has been observed: not only did they learn more but also the teachers were able to improve their own methods.

Per-Pixel Coded Exposure for High-Speed and High-Resolution Imaging Using a Digital Micromirror Device Camera

PubMed Central

Feng, Wei; Zhang, Fumin; Qu, Xinghua; Zheng, Shiwei

2016-01-01

High-speed photography is an important tool for studying rapid physical phenomena. However, low-frame-rate CCD (charge coupled device) or CMOS (complementary metal oxide semiconductor) camera cannot effectively capture the rapid phenomena with high-speed and high-resolution. In this paper, we incorporate the hardware restrictions of existing image sensors, design the sampling functions, and implement a hardware prototype with a digital micromirror device (DMD) camera in which spatial and temporal information can be flexibly modulated. Combined with the optical model of DMD camera, we theoretically analyze the per-pixel coded exposure and propose a three-element median quicksort method to increase the temporal resolution of the imaging system. Theoretically, this approach can rapidly increase the temporal resolution several, or even hundreds, of times without increasing bandwidth requirements of the camera. We demonstrate the effectiveness of our method via extensive examples and achieve 100 fps (frames per second) gain in temporal resolution by using a 25 fps camera. PMID:26959023

Per-Pixel Coded Exposure for High-Speed and High-Resolution Imaging Using a Digital Micromirror Device Camera.

PubMed

Feng, Wei; Zhang, Fumin; Qu, Xinghua; Zheng, Shiwei

2016-03-04

High-speed photography is an important tool for studying rapid physical phenomena. However, low-frame-rate CCD (charge coupled device) or CMOS (complementary metal oxide semiconductor) camera cannot effectively capture the rapid phenomena with high-speed and high-resolution. In this paper, we incorporate the hardware restrictions of existing image sensors, design the sampling functions, and implement a hardware prototype with a digital micromirror device (DMD) camera in which spatial and temporal information can be flexibly modulated. Combined with the optical model of DMD camera, we theoretically analyze the per-pixel coded exposure and propose a three-element median quicksort method to increase the temporal resolution of the imaging system. Theoretically, this approach can rapidly increase the temporal resolution several, or even hundreds, of times without increasing bandwidth requirements of the camera. We demonstrate the effectiveness of our method via extensive examples and achieve 100 fps (frames per second) gain in temporal resolution by using a 25 fps camera.

Assessing Cost-Effectiveness in Obesity (ACE-Obesity): an overview of the ACE approach, economic methods and cost results

PubMed Central

2009-01-01

Background The aim of the ACE-Obesity study was to determine the economic credentials of interventions which aim to prevent unhealthy weight gain in children and adolescents. We have reported elsewhere on the modelled effectiveness of 13 obesity prevention interventions in children. In this paper, we report on the cost results and associated methods together with the innovative approach to priority setting that underpins the ACE-Obesity study. Methods The Assessing Cost Effectiveness (ACE) approach combines technical rigour with 'due process' to facilitate evidence-based policy analysis. Technical rigour was achieved through use of standardised evaluation methods, a research team that assembles best available evidence and extensive uncertainty analysis. Cost estimates were based on pathway analysis, with resource usage estimated for the interventions and their 'current practice' comparator, as well as associated cost offsets. Due process was achieved through involvement of stakeholders, consensus decisions informed by briefing papers and 2nd stage filter analysis that captures broader factors that influence policy judgements in addition to cost-effectiveness results. The 2nd stage filters agreed by stakeholders were 'equity', 'strength of the evidence', 'feasibility of implementation', 'acceptability to stakeholders', 'sustainability' and 'potential for side-effects'. Results The intervention costs varied considerably, both in absolute terms (from cost saving [6 interventions] to in excess of AUD50m per annum) and when expressed as a 'cost per child' estimate (from

DOE Office of Scientific and Technical Information (OSTI.GOV)

Unkelbach, Jan, E-mail: junkelbach@mgh.harvard.edu; Botas, Pablo; Faculty of Physics, Ruprecht-Karls-Universität Heidelberg, Heidelberg

Purpose: We describe a treatment plan optimization method for intensity modulated proton therapy (IMPT) that avoids high values of linear energy transfer (LET) in critical structures located within or near the target volume while limiting degradation of the best possible physical dose distribution. Methods and Materials: To allow fast optimization based on dose and LET, a GPU-based Monte Carlo code was extended to provide dose-averaged LET in addition to dose for all pencil beams. After optimizing an initial IMPT plan based on physical dose, a prioritized optimization scheme is used to modify the LET distribution while constraining the physical dosemore » objectives to values close to the initial plan. The LET optimization step is performed based on objective functions evaluated for the product of LET and physical dose (LET×D). To first approximation, LET×D represents a measure of the additional biological dose that is caused by high LET. Results: The method is effective for treatments where serial critical structures with maximum dose constraints are located within or near the target. We report on 5 patients with intracranial tumors (high-grade meningiomas, base-of-skull chordomas, ependymomas) in whom the target volume overlaps with the brainstem and optic structures. In all cases, high LET×D in critical structures could be avoided while minimally compromising physical dose planning objectives. Conclusion: LET-based reoptimization of IMPT plans represents a pragmatic approach to bridge the gap between purely physical dose-based and relative biological effectiveness (RBE)-based planning. The method makes IMPT treatments safer by mitigating a potentially increased risk of side effects resulting from elevated RBE of proton beams near the end of range.« less

Reliable Exfoliation of Large-Area High-Quality Flakes of Graphene and Other Two-Dimensional Materials.

PubMed

Huang, Yuan; Sutter, Eli; Shi, Norman N; Zheng, Jiabao; Yang, Tianzhong; Englund, Dirk; Gao, Hong-Jun; Sutter, Peter

2015-11-24

Mechanical exfoliation has been a key enabler of the exploration of the properties of two-dimensional materials, such as graphene, by providing routine access to high-quality material. The original exfoliation method, which remained largely unchanged during the past decade, provides relatively small flakes with moderate yield. Here, we report a modified approach for exfoliating thin monolayer and few-layer flakes from layered crystals. Our method introduces two process steps that enhance and homogenize the adhesion force between the outermost sheet in contact with a substrate: Prior to exfoliation, ambient adsorbates are effectively removed from the substrate by oxygen plasma cleaning, and an additional heat treatment maximizes the uniform contact area at the interface between the source crystal and the substrate. For graphene exfoliation, these simple process steps increased the yield and the area of the transferred flakes by more than 50 times compared to the established exfoliation methods. Raman and AFM characterization shows that the graphene flakes are of similar high quality as those obtained in previous reports. Graphene field-effect devices were fabricated and measured with back-gating and solution top-gating, yielding mobilities of ∼4000 and 12,000 cm(2)/(V s), respectively, and thus demonstrating excellent electrical properties. Experiments with other layered crystals, e.g., a bismuth strontium calcium copper oxide (BSCCO) superconductor, show enhancements in exfoliation yield and flake area similar to those for graphene, suggesting that our modified exfoliation method provides an effective way for producing large area, high-quality flakes of a wide range of 2D materials.

Performance Sensitivity Studies on the PIAA Implementation of the High-Contrast Imaging Testbed

NASA Technical Reports Server (NTRS)

Sidick, Erkin; Lou, John; Shaklan, Stuart; Levine, Marie

2010-01-01

This slide presentation reviews the sensitivity studies on the Phase-Induced Amplitude Apodization (PIAA), or pupil mapping using the High-Contrast Imaging Testbed (HCIT). PIAA is a promising technique in high-dynamic range stellar coronagraph. This presentation reports on the investigation of the effects of the phase and rigid-body errors of various optics on the narrowband contrast performance of the PIAA/HCIT hybrid system. The results have shown that the 2-step wavefront control method utilizing 2-DMs is quite effective in compensating the effects of realistic phase and rigid-body errors of various optics

The research on the mean shift algorithm for target tracking

NASA Astrophysics Data System (ADS)

CAO, Honghong

2017-06-01

The traditional mean shift algorithm for target tracking is effective and high real-time, but there still are some shortcomings. The traditional mean shift algorithm is easy to fall into local optimum in the tracking process, the effectiveness of the method is weak when the object is moving fast. And the size of the tracking window never changes, the method will fail when the size of the moving object changes, as a result, we come up with a new method. We use particle swarm optimization algorithm to optimize the mean shift algorithm for target tracking, Meanwhile, SIFT (scale-invariant feature transform) and affine transformation make the size of tracking window adaptive. At last, we evaluate the method by comparing experiments. Experimental result indicates that the proposed method can effectively track the object and the size of the tracking window changes.

A literature review on fatigue and creep interaction

NASA Technical Reports Server (NTRS)

Chen, W. C.

1978-01-01

Life-time prediction methods, which are based on a number of empirical and phenomenological relationships, are presented. Three aspects are reviewed: effects of testing parameters on high temperature fatigue, life-time prediction, and high temperature fatigue crack growth.

Engineering and Characterizing Light-Matter Interactions in Photonic Crystals

DTIC Science & Technology

2010-01-01

photonic crystal effects would occur at wavelengths in the infrared spectrum. These effects would not be easily measured by our available...spectrometers which operate in the visible and near- infrared , at wavelengths shorter than 1.6 microns. Similarly, the majority of interesting luminescent...periodicity of the photonic crystal is defined by the high -throughput method while the low-throughput method performs the complementary task of adding a

Time-Dependent Traveling Wave Tube Model for Intersymbol Interference Investigations

DTIC Science & Technology

2001-06-01

band is 5.7 degrees. C. Differences between broadband and single-tone excitations The TWT characteristics are compared when excited by single-tones...direct description of the effects of the TWT on modulated digital signals. The TWT model comprehensively takes into account the effects of frequency...of the high power amplifier and the operational digital signal. This method promises superior predictive fidelity compared to methods using TWT

Examining the Implementation of a Problem-Based Learning and Traditional Hybrid Model of Instruction in Remedial Mathematics Classes Designed for State Testing Preparation of Eleventh Grade Students

ERIC Educational Resources Information Center

Rodgers, Lindsay D.

2011-01-01

The following paper examined the effects of a new method of teaching for remedial mathematics, named the hybrid model of instruction. Due to increasing importance of high stakes testing, the study sought to determine if this method of instruction, that blends traditional teaching and problem-based learning, had different learning effects on…

Magnetic fields end-face effect investigation of HTS bulk over PMG with 3D-modeling numerical method

NASA Astrophysics Data System (ADS)

Qin, Yujie; Lu, Yiyun

2015-09-01

In this paper, the magnetic fields end-face effect of high temperature superconducting (HTS) bulk over a permanent magnetic guideway (PMG) is researched with 3D-modeling numerical method. The electromagnetic behavior of the bulk is simulated using finite element method (FEM). The framework is formulated by the magnetic field vector method (H-method). A superconducting levitation system composed of one rectangular HTS bulk and one infinite long PMG is successfully investigated using the proposed method. The simulation results show that for finite geometrical HTS bulk, even the applied magnetic field is only distributed in x-y plane, the magnetic field component Hz which is along the z-axis can be observed interior the HTS bulk.

The algorithm for duration acceleration of repetitive projects considering the learning effect

NASA Astrophysics Data System (ADS)

Chen, Hongtao; Wang, Keke; Du, Yang; Wang, Liwan

2018-03-01

Repetitive project optimization problem is common in project scheduling. Repetitive Scheduling Method (RSM) has many irreplaceable advantages in the field of repetitive projects. As the same or similar work is repeated, the proficiency of workers will be correspondingly low to high, and workers will gain experience and improve the efficiency of operations. This is learning effect. Learning effect is one of the important factors affecting the optimization results in repetitive project scheduling. This paper analyzes the influence of the learning effect on the controlling path in RSM from two aspects: one is that the learning effect changes the controlling path, the other is that the learning effect doesn't change the controlling path. This paper proposes corresponding methods to accelerate duration for different types of critical activities and proposes the algorithm for duration acceleration based on the learning effect in RSM. And the paper chooses graphical method to identity activities' types and considers the impacts of the learning effect on duration. The method meets the requirement of duration while ensuring the lowest acceleration cost. A concrete bridge construction project is given to verify the effectiveness of the method. The results of this study will help project managers understand the impacts of the learning effect on repetitive projects, and use the learning effect to optimize project scheduling.

Statistical methods for analysing responses of wildlife to human disturbance.

Treesearch

Haiganoush K. Preisler; Alan A. Ager; Michael J. Wisdom

2006-01-01

1. Off-road recreation is increasing rapidly in many areas of the world, and effects on wildlife can be highly detrimental. Consequently, we have developed methods for studying wildlife responses to off-road recreation with the use of new technologies that allow frequent and accurate monitoring of human-wildlife interactions. To illustrate these methods, we studied the...

A Guideline of Using Case Method in Software Engineering Courses

ERIC Educational Resources Information Center

Zainal, Dzulaiha Aryanee Putri; Razali, Rozilawati; Shukur, Zarina

2014-01-01

Software Engineering (SE) education has been reported to fall short in producing high quality software engineers. In seeking alternative solutions, Case Method (CM) is regarded as having potential to solve the issue. CM is a teaching and learning (T&L) method that has been found to be effective in Social Science education. In principle,…

Front and backside processed thin film electronic devices

DOEpatents

Yuan, Hao-Chih; Wang, Guogong; Eriksson, Mark A.; Evans, Paul G.; Lagally, Max G.; Ma, Zhenqiang

2010-10-12

This invention provides methods for fabricating thin film electronic devices with both front- and backside processing capabilities. Using these methods, high temperature processing steps may be carried out during both frontside and backside processing. The methods are well-suited for fabricating back-gate and double-gate field effect transistors, double-sided bipolar transistors and 3D integrated circuits.

Semi-automatic sparse preconditioners for high-order finite element methods on non-uniform meshes

NASA Astrophysics Data System (ADS)

Austin, Travis M.; Brezina, Marian; Jamroz, Ben; Jhurani, Chetan; Manteuffel, Thomas A.; Ruge, John

2012-05-01

High-order finite elements often have a higher accuracy per degree of freedom than the classical low-order finite elements. However, in the context of implicit time-stepping methods, high-order finite elements present challenges to the construction of efficient simulations due to the high cost of inverting the denser finite element matrix. There are many cases where simulations are limited by the memory required to store the matrix and/or the algorithmic components of the linear solver. We are particularly interested in preconditioned Krylov methods for linear systems generated by discretization of elliptic partial differential equations with high-order finite elements. Using a preconditioner like Algebraic Multigrid can be costly in terms of memory due to the need to store matrix information at the various levels. We present a novel method for defining a preconditioner for systems generated by high-order finite elements that is based on a much sparser system than the original high-order finite element system. We investigate the performance for non-uniform meshes on a cube and a cubed sphere mesh, showing that the sparser preconditioner is more efficient and uses significantly less memory. Finally, we explore new methods to construct the sparse preconditioner and examine their effectiveness for non-uniform meshes. We compare results to a direct use of Algebraic Multigrid as a preconditioner and to a two-level additive Schwarz method.

Method for the substantial reduction of quenching effects in luminescence spectrometry

DOEpatents

Demas, James N.; Jones, Wesley M.; Keller, Richard A.

1989-01-01

Method for reducing quenching effects in analytical luminescence measurements. Two embodiments of the present invention are described which relate to a form of time resolution based on the amplitudes and phase shifts of modulated emission signals. In the first embodiment, the measured modulated emission signal is substantially independent of sample quenching at sufficiently high frequenices. In the second embodiment, the modulated amplitude and the phase shift between the emission signal and the excitation source are simultaneously measured. Using either method, the observed modulated amplitude may reduced to tis unquenched value.

PA03.13. Effect of triphaladi rasayana along with yoga therapy on low grade non hodgkins lymphoma and resistant intermediate and high grade non hodgkins lymphoma

PubMed Central

Soumya, MS Surya; Sarasa, TP

2013-01-01

Purpose: 1. To find out the effect of Thriphaladi Rasayana along with Yoga Therapy on low grade Non Hodgkins Lymphoma and resistant intermediate and high grade NonHodgkins Lymphoma. 2. To apply a less costly, less morbid, well accepted method of treatment on NHL. 3.To find a simple method to increase the immunity. 4.To try a drug which is easy to prepare? Method: Purposive sampling technique was used for the study. Sample of 30 patients age range 25 75 years with histologicaly proven NonHodgkins lymphoma, attending the M.O.I.O.P of the regional cancer centre during a period of 18 months. Groups1) Low grade NonHodgkins Lymphoma 2) Resistant intermediate &High grade NonHodgkins lymphoma (failed chemotherapy) were taken. Procedure : 2 groups were given Triphaladhi Rasayana (15 grams of powder with ghee and honey) twice dailymorning& at bed time with milk as anupana for period of 1month along with selected yoga asanas and niyama? Result: Symptoms included were fever, night sweats, weight loss, lymph nodes enlargement, splenomegaly, and hepatomegaly. In low grade symptom relief was noted in almost all cases. Lymph node changes notedLow grade5 2% (complete remission), 38% (partial remission), 10% (no change), intermediate35% (CR), 52% (PR) & 13% (NC), High grade67% (CR), 33%(PR). Hepatomegaly changes :ve in low grade92.86%, intermediate 90.9% & high grade100%. Splenomegaly changes :ve in low grade92.86%, intermediate72.72% & high grade80% Over all remission status of 30 patientscomplete remission30%, partial remission 30% & no change30%? Conclusion: Thriphaladirasayana along with Yoga therapy is very effective in Low grade NonHodgkins lymphoma and resistant intermediate and high grade Non hodgkins Lymphoma?

Hardness Assurance for Low-Energy Proton-Induced Single-Event Effects: Final report for LDRD Project 173134

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dodds, Nathaniel Anson

2015-08-01

This report briefly summarizes three publications that resulted from a two-year LDRD. The three publications address a recently emerging reliability issue: namely, that low-energy protons (LEPs) can cause single-event effects (SEEs) in highly scaled microelectronics. These publications span from low to high technology readiness levels. In the first, novel experiments were used to prove that proton direct ionization is the dominant mechanism for LEP-induced SEEs. In the second, a simple method was developed to calculate expected on-orbit error rates for LEP effects. This simplification was enabled by creating (and characterizing) an accelerated space-like LEP environment in the laboratory. In themore » third publication, this new method was applied to many memory circuits from the 20-90 nm technology nodes to study the general importance of LEP effects, in terms of their contribution to the total on-orbit SEE rate.« less

Academic Vocabulary Learning in First through Third Grade in Low-Income Schools: Effects of Automated Supplemental Instruction

ERIC Educational Resources Information Center

Goldstein, Howard; Ziolkowski, Robyn A.; Bojczyk, Kathryn E.; Marty, Ana; Schneider, Naomi; Harpring, Jayme; Haring, Christa D.

2017-01-01

Purpose: This study investigated cumulative effects of language learning, specifically whether prior vocabulary knowledge or special education status moderated the effects of academic vocabulary instruction in high-poverty schools. Method: Effects of a supplemental intervention targeting academic vocabulary in first through third grades were…

Infrared fix pattern noise reduction method based on Shearlet Transform

NASA Astrophysics Data System (ADS)

Rong, Shenghui; Zhou, Huixin; Zhao, Dong; Cheng, Kuanhong; Qian, Kun; Qin, Hanlin

2018-06-01

The non-uniformity correction (NUC) is an effective way to reduce fix pattern noise (FPN) and improve infrared image quality. The temporal high-pass NUC method is a kind of practical NUC method because of its simple implementation. However, traditional temporal high-pass NUC methods rely deeply on the scene motion and suffer image ghosting and blurring. Thus, this paper proposes an improved NUC method based on Shearlet Transform (ST). First, the raw infrared image is decomposed into multiscale and multi-orientation subbands by ST and the FPN component mainly exists in some certain high-frequency subbands. Then, high-frequency subbands are processed by the temporal filter to extract the FPN due to its low-frequency characteristics. Besides, each subband has a confidence parameter to determine the degree of FPN, which is estimated by the variance of subbands adaptively. At last, the process of NUC is achieved by subtracting the estimated FPN component from the original subbands and the corrected infrared image can be obtained by the inverse ST. The performance of the proposed method is evaluated with real and synthetic infrared image sequences thoroughly. Experimental results indicate that the proposed method can reduce heavily FPN with less roughness and RMSE.

Evaluation of a Cubature Kalman Filtering-Based Phase Unwrapping Method for Differential Interferograms with High Noise in Coal Mining Areas

PubMed Central

Liu, Wanli; Bian, Zhengfu; Liu, Zhenguo; Zhang, Qiuzhao

2015-01-01

Differential interferometric synthetic aperture radar has been shown to be effective for monitoring subsidence in coal mining areas. Phase unwrapping can have a dramatic influence on the monitoring result. In this paper, a filtering-based phase unwrapping algorithm in combination with path-following is introduced to unwrap differential interferograms with high noise in mining areas. It can perform simultaneous noise filtering and phase unwrapping so that the pre-filtering steps can be omitted, thus usually retaining more details and improving the detectable deformation. For the method, the nonlinear measurement model of phase unwrapping is processed using a simplified Cubature Kalman filtering, which is an effective and efficient tool used in many nonlinear fields. Three case studies are designed to evaluate the performance of the method. In Case 1, two tests are designed to evaluate the performance of the method under different factors including the number of multi-looks and path-guiding indexes. The result demonstrates that the unwrapped results are sensitive to the number of multi-looks and that the Fisher Distance is the most suitable path-guiding index for our study. Two case studies are then designed to evaluate the feasibility of the proposed phase unwrapping method based on Cubature Kalman filtering. The results indicate that, compared with the popular Minimum Cost Flow method, the Cubature Kalman filtering-based phase unwrapping can achieve promising results without pre-filtering and is an appropriate method for coal mining areas with high noise. PMID:26153776

Diffusion length measurements using the scanning electron microscope. [in semiconductor devices

NASA Technical Reports Server (NTRS)

Weizer, V. G.

1975-01-01

A measurement technique employing the scanning electron microscope is described in which values of the true bulk diffusion length are obtained. It is shown that surface recombination effects can be eliminated through the application of highly doped surface field layers. The influence of high injection level effects and low-high junction current generation on the resulting measurement was investigated. Close agreement is found between the diffusion lengths measured by this method and those obtained using a penetrating radiation technique.

High intensity focused ultrasound (HIFU) in tumor therapy.

PubMed

Sequeiros, Roberto Blanco; Joronen, Kirsi; Komar, Gaber; Koskinen, Seppo K

HIFU (high intensity focused ultrasound) is a method in which high-frequency ultrasound is focused on a tissue in order to achieve a thermal effect and the subsequent percutaneously ablation, or tissue modulation. HIFU is non-invasive and results in an immediate tissue destruction effect corresponding to surgery, either percutaneously or through body cavities. HIFU can be utilized in the treatment of both benign and malignant tumors. In neurological diseases, focused HIFU can be used in the treatment of disorders of the basal ganglia.

The Effect of Parenting Stress on Child Behavior Problems in High-Risk Children with Prenatal Drug Exposure

ERIC Educational Resources Information Center

Bagner, Daniel M.; Sheinkopf, Stephen J.; Miller-Loncar, Cynthia; LaGasse, Linda L.; Lester, Barry M.; Liu, Jing; Bauer, Charles R.; Shankaran, Seetha; Bada, Henrietta; Das, Abhik

2009-01-01

Objective: To examine the relationship between early parenting stress and later child behavior in a high-risk sample and measure the effect of drug exposure on the relationship between parenting stress and child behavior. Methods: A subset of child-caregiver dyads (n = 607) were selected from the Maternal Lifestyle Study (MLS), which is a large…

Efficacy Trial of a Brief Cognitive-Behavioral Depression Prevention Program for High-Risk Adolescents: Effects at 1- and 2-Year Follow-Up

ERIC Educational Resources Information Center

Stice, Eric; Rohde, Paul; Gau, Jeff M.; Wade, Emily

2010-01-01

Objective: To evaluate the effects of a brief group cognitive-behavioral (CB) depression prevention program for high-risk adolescents with elevated depressive symptoms at 1- and 2-year follow-up. Method: In this indicated prevention trial, 341 at-risk youths were randomized to a group CB intervention, group supportive expressive intervention, CB…

Effects of an Intellectually Caring Model on Urban African American Alternative High School Students' Conceptual Change and Achievement in Chemistry

ERIC Educational Resources Information Center

Wood, Lynda C.; Ebenezer, Jazlin; Boone, Relena

2013-01-01

The purpose of this article is to study the effects of an intellectually caring model of teaching and learning on alternative African American high school students' conceptual change and achievement in a chemistry unit on acids and bases. A mixed-methods approach using retrospective data was utilized. Data secured from the teacher were the…

Effect of revised high-heeled shoes on foot pressure and static balance during standing.

PubMed

Bae, Young-Hyeon; Ko, Mansoo; Park, Young-Soul; Lee, Suk-Min

2015-04-01

[Purpose] The purpose of this study was to investigate the effects of revised high-heeled shoes on the foot pressure ratio and static balance during standing. [Subjects and Methods] A single-subject design was used, 15 healthy women wearing revised high-heeled shoes and general high-heeled shoes in a random order. The foot pressure ratio and static balance scores during standing were measured using a SpaceBalance 3D system. [Results] Forefoot and rearfoot pressures were significantly different between the 2 types of high-heeled shoes. Under the 3 conditions tested, the static balance score was higher for the revised high-heeled shoes than for the general high-heeled shoes, but this difference was not statistically significant. [Conclusion] Revised high-heeled shoes are preferable to general high-heeled shoes, as they result in normalization of normalized foot pressure and a positive effect on static balance.

Effect of revised high-heeled shoes on foot pressure and static balance during standing

PubMed Central

Bae, Young-Hyeon; Ko, Mansoo; Park, Young-Soul; Lee, Suk-Min

2015-01-01

[Purpose] The purpose of this study was to investigate the effects of revised high-heeled shoes on the foot pressure ratio and static balance during standing. [Subjects and Methods] A single-subject design was used, 15 healthy women wearing revised high-heeled shoes and general high-heeled shoes in a random order. The foot pressure ratio and static balance scores during standing were measured using a SpaceBalance 3D system. [Results] Forefoot and rearfoot pressures were significantly different between the 2 types of high-heeled shoes. Under the 3 conditions tested, the static balance score was higher for the revised high-heeled shoes than for the general high-heeled shoes, but this difference was not statistically significant. [Conclusion] Revised high-heeled shoes are preferable to general high-heeled shoes, as they result in normalization of normalized foot pressure and a positive effect on static balance. PMID:25995572

Exploiting jet binning to identify the initial state of high-mass resonances

NASA Astrophysics Data System (ADS)

Ebert, Markus A.; Liebler, Stefan; Moult, Ian; Stewart, Iain W.; Tackmann, Frank J.; Tackmann, Kerstin; Zeune, Lisa

2016-09-01

If a new high-mass resonance is discovered at the Large Hadron Collider, model-independent techniques to identify the production mechanism will be crucial to understand its nature and effective couplings to Standard Model particles. We present a powerful and model-independent method to infer the initial state in the production of any high-mass color-singlet system by using a tight veto on accompanying hadronic jets to divide the data into two mutually exclusive event samples (jet bins). For a resonance of several hundred GeV, the jet binning cut needed to discriminate quark and gluon initial states is in the experimentally accessible range of several tens of GeV. It also yields comparable cross sections for both bins, making this method viable already with the small event samples available shortly after a discovery. Theoretically, the method is made feasible by utilizing an effective field theory setup to compute the jet cut dependence precisely and model independently and to systematically control all sources of theoretical uncertainties in the jet binning, as well as their correlations. We use a 750 GeV scalar resonance as an example to demonstrate the viability of our method.

A family-based probabilistic method for capturing de novo mutations from high-throughput short-read sequencing data.

PubMed

Cartwright, Reed A; Hussin, Julie; Keebler, Jonathan E M; Stone, Eric A; Awadalla, Philip

2012-01-06

Recent advances in high-throughput DNA sequencing technologies and associated statistical analyses have enabled in-depth analysis of whole-genome sequences. As this technology is applied to a growing number of individual human genomes, entire families are now being sequenced. Information contained within the pedigree of a sequenced family can be leveraged when inferring the donors' genotypes. The presence of a de novo mutation within the pedigree is indicated by a violation of Mendelian inheritance laws. Here, we present a method for probabilistically inferring genotypes across a pedigree using high-throughput sequencing data and producing the posterior probability of de novo mutation at each genomic site examined. This framework can be used to disentangle the effects of germline and somatic mutational processes and to simultaneously estimate the effect of sequencing error and the initial genetic variation in the population from which the founders of the pedigree arise. This approach is examined in detail through simulations and areas for method improvement are noted. By applying this method to data from members of a well-defined nuclear family with accurate pedigree information, the stage is set to make the most direct estimates of the human mutation rate to date.

Sterilization of beehive material with a double inductively coupled low pressure plasma

NASA Astrophysics Data System (ADS)

Priehn, M.; Denis, B.; Aumeier, P.; Kirchner, W. H.; Awakowicz, P.; Leichert, L. I.

2016-09-01

American Foulbrood is a severe, notifiable disease of the honey bee. It is caused by infection of bee larvae with spores of the gram-positive bacterium Paenibacillus larvae. Spores of this organism are found in high numbers in an infected hive and are highly resistant to physical and chemical inactivation methods. The procedures to rehabilitate affected apiaries often result in the destruction of beehive material. In this study we assess the suitability of a double inductively coupled low pressure plasma as a non-destructive, yet effective alternative inactivation method for bacterial spores of the model organism Bacillus subtilis on beehive material. Plasma treatment was able to effectively remove spores from wax, which, under protocols currently established in veterinary practice, normally is destroyed by ignition or autoclaved for sterilization. Spores were removed from wooden surfaces with efficacies significantly higher than methods currently used in veterinary practice, such as scorching by flame treatment. In addition, we were able to non-destructively remove spores from the highly delicate honeycomb wax structures, potentially making treatment of beehive material with double inductively coupled low pressure plasma part of a fast and reliable method to rehabilitate infected bee colonies with the potential to re-use honeycombs.

Sparse representations via learned dictionaries for x-ray angiogram image denoising

NASA Astrophysics Data System (ADS)

Shang, Jingfan; Huang, Zhenghua; Li, Qian; Zhang, Tianxu

2018-03-01

X-ray angiogram image denoising is always an active research topic in the field of computer vision. In particular, the denoising performance of many existing methods had been greatly improved by the widely use of nonlocal similar patches. However, the only nonlocal self-similar (NSS) patch-based methods can be still be improved and extended. In this paper, we propose an image denoising model based on the sparsity of the NSS patches to obtain high denoising performance and high-quality image. In order to represent the sparsely NSS patches in every location of the image well and solve the image denoising model more efficiently, we obtain dictionaries as a global image prior by the K-SVD algorithm over the processing image; Then the single and effectively alternating directions method of multipliers (ADMM) method is used to solve the image denoising model. The results of widely synthetic experiments demonstrate that, owing to learned dictionaries by K-SVD algorithm, a sparsely augmented lagrangian image denoising (SALID) model, which perform effectively, obtains a state-of-the-art denoising performance and better high-quality images. Moreover, we also give some denoising results of clinical X-ray angiogram images.

High accurate interpolation of NURBS tool path for CNC machine tools

NASA Astrophysics Data System (ADS)

Liu, Qiang; Liu, Huan; Yuan, Songmei

2016-09-01

Feedrate fluctuation caused by approximation errors of interpolation methods has great effects on machining quality in NURBS interpolation, but few methods can efficiently eliminate or reduce it to a satisfying level without sacrificing the computing efficiency at present. In order to solve this problem, a high accurate interpolation method for NURBS tool path is proposed. The proposed method can efficiently reduce the feedrate fluctuation by forming a quartic equation with respect to the curve parameter increment, which can be efficiently solved by analytic methods in real-time. Theoretically, the proposed method can totally eliminate the feedrate fluctuation for any 2nd degree NURBS curves and can interpolate 3rd degree NURBS curves with minimal feedrate fluctuation. Moreover, a smooth feedrate planning algorithm is also proposed to generate smooth tool motion with considering multiple constraints and scheduling errors by an efficient planning strategy. Experiments are conducted to verify the feasibility and applicability of the proposed method. This research presents a novel NURBS interpolation method with not only high accuracy but also satisfying computing efficiency.

Effects of two educational method of lecturing and role playing on knowledge and performance of high school students in first aid at emergency scene

PubMed Central

Hassanzadeh, Akbar; Vasili, Arezu; Zare, Zahra

2010-01-01

BACKGROUND: This study aimed to investigate the effects of two educational methods on students' knowledge and performance regarding first aid at emergency scenes. METHODS: In this semi-experimental study, the sample was selected randomly among male and female public high school students of Isfahan. Each group included 60 students. At first the knowledge and performance of students in first aid at emergency scene was assessed using a researcher-made questionnaire. Then necessary education was provided to the students within 10 sessions of two hours by lecturing and role playing. The students' knowledge and performance was as-sessed again and the results were compared. RESULTS: It was no significant relationship between the frequency distribution of students' age, major and knowledge and performance before the educational course in the two groups. The score of knowledge in performing CPR, using proper way to bandage, immobilizing the injured area, and proper ways of carrying injured person after the education was significantly increased in both groups. Moreover, the performance in proper way to bandage, immobilizing injured area and proper ways of carrying injured person after educational course was significantly higher in playing role group compared to lecturing group after education. CONCLUSIONS: Iran is a developing country with a young generation and it is a country with high risk of natural disasters; so, providing necessary education with more effective methods can be effective in reducing mortality and morbidity due to lack of first aid care in crucial moments. Training with playing role is suggested for this purpose. PMID:21589743

Adaptive temperature-accelerated dynamics

NASA Astrophysics Data System (ADS)

Shim, Yunsic; Amar, Jacques G.

2011-02-01

We present three adaptive methods for optimizing the high temperature Thigh on-the-fly in temperature-accelerated dynamics (TAD) simulations. In all three methods, the high temperature is adjusted periodically in order to maximize the performance. While in the first two methods the adjustment depends on the number of observed events, the third method depends on the minimum activation barrier observed so far and requires an a priori knowledge of the optimal high temperature T^{opt}_{high}(E_a) as a function of the activation barrier Ea for each accepted event. In order to determine the functional form of T^{opt}_{high}(E_a), we have carried out extensive simulations of submonolayer annealing on the (100) surface for a variety of metals (Ag, Cu, Ni, Pd, and Au). While the results for all five metals are different, when they are scaled with the melting temperature Tm, we find that they all lie on a single scaling curve. Similar results have also been obtained for (111) surfaces although in this case the scaling function is slightly different. In order to test the performance of all three methods, we have also carried out adaptive TAD simulations of Ag/Ag(100) annealing and growth at T = 80 K and compared with fixed high-temperature TAD simulations for different values of Thigh. We find that the performance of all three adaptive methods is typically as good as or better than that obtained in fixed high-temperature TAD simulations carried out using the effective optimal fixed high temperature. In addition, we find that the final high temperatures obtained in our adaptive TAD simulations are very close to our results for T^{opt}_{high}(E_a). The applicability of the adaptive methods to a variety of TAD simulations is also briefly discussed.

Blanking Method with Aid of Scrap to Reduce Tensile Residual Stress on Sheared Edge

NASA Astrophysics Data System (ADS)

Yasutomi, T.; Yonemura, S.; Yoshida, T.; Mizumura, M.; Hiwatashi, S.

2017-09-01

A simple shearing method to reduce tensile residual stress on a sheared edge is highly desired in the automotive industry because this type of stress deteriorates the fatigue property of automotive parts. In this study, the effect of a coining method with a shearing scrap material on a sheared edge was investigated. The scrap part of a sheared plate has a fracture surface shape similar to that of the product part since these parts are generated by separation of a single plate with crack propagation. Therefore, it is possible to impose plastic strain over the entire fracture surface by using the scrap part as a coining tool. Effectiveness of this method was investigated for high-tensile-strength steel. Using this method, the tensile residual stress on the sheared surface was significantly reduced and work hardening was slightly increased. The effects of shearing clearance and coining stroke were also investigated. Tensile residual stress decreased as the coining stroke increased; however, it saturated at a certain stroke. The stroke at which tensile residual stress saturated was relatively small at a large clearance. In particular, the amount of plastic deformation on fracture surface increased when coining stroke became large. These tendencies could be explained by the conditions of contact, which were investigated using finite element analysis.

Contamination mitigation strategies for scanning transmission electron microscopy.

PubMed

Mitchell, D R G

2015-06-01

Modern scanning transmission electron microscopy (STEM) enables imaging and microanalysis at very high magnification. In the case of aberration-corrected STEM, atomic resolution is readily achieved. However, the electron fluxes used may be up to three orders of magnitude greater than those typically employed in conventional STEM. Since specimen contamination often increases with electron flux, specimen cleanliness is a critical factor in obtaining meaningful data when carrying out high magnification STEM. A range of different specimen cleaning methods have been applied to a variety of specimen types. The contamination rate has been measured quantitatively to assess the effectiveness of cleaning. The methods studied include: baking, cooling, plasma cleaning, beam showering and UV/ozone exposure. Of the methods tested, beam showering is rapid, experimentally convenient and very effective on a wide range of specimens. Oxidative plasma cleaning is also very effective and can be applied to specimens on carbon support films, albeit with some care. For electron beam-sensitive materials, cooling may be the method of choice. In most cases, preliminary removal of the bulk of the contamination by methods such as baking or plasma cleaning, followed by beam showering, where necessary, can result in a contamination-free specimen suitable for extended atomic scale imaging and analysis. Copyright © 2015 Elsevier Ltd. All rights reserved.

Wavelet filter analysis of local atmospheric pressure effects in the long-period tidal bands

NASA Astrophysics Data System (ADS)

Hu, X.-G.; Liu, L. T.; Ducarme, B.; Hsu, H. T.; Sun, H.-P.

2006-11-01

It is well known that local atmospheric pressure variations obviously affect the observation of short-period Earth tides, such as diurnal tides, semi-diurnal tides and ter-diurnal tides, but local atmospheric pressure effects on the long-period Earth tides have not been studied in detail. This is because the local atmospheric pressure is believed not to be sufficient for an effective pressure correction in long-period tidal bands, and there are no efficient methods to investigate local atmospheric effects in these bands. The usual tidal analysis software package, such as ETERNA, Baytap-G and VAV, cannot provide detailed pressure admittances for long-period tidal bands. We propose a wavelet method to investigate local atmospheric effects on gravity variations in long-period tidal bands. This method constructs efficient orthogonal filter bank with Daubechies wavelets of high vanishing moments. The main advantage of the wavelet filter bank is that it has excellent low frequency response and efficiently suppresses instrumental drift of superconducting gravimeters (SGs) without using any mathematical model. Applying the wavelet method to the 13-year continuous gravity observations from SG T003 in Brussels, Belgium, we filtered 12 long-period tidal groups into eight narrow frequency bands. Wavelet method demonstrates that local atmospheric pressure fluctuations are highly correlated with the noise of SG measurements in the period band 4-40 days with correlation coefficients higher than 0.95 and local atmospheric pressure variations are the main error source for the determination of the tidal parameters in these bands. We show the significant improvement of long-period tidal parameters provided by wavelet method in term of precision.

Pregnancy desire and dual method contraceptive use among people living with HIV attending clinical care in Kenya, Namibia and Tanzania.

PubMed

Antelman, Gretchen; Medley, Amy; Mbatia, Redempta; Pals, Sherri; Arthur, Gilly; Haberlen, Sabina; Ackers, Marta; Elul, Batya; Parent, Julie; Rwebembera, Anath; Wanjiku, Lucy; Muraguri, Nicholas; Gweshe, Justice; Mudhune, Sandra; Bachanas, Pamela

2015-01-01

To describe factors associated with pregnancy desire and dual method use among people living with HIV in clinical care in sub-Saharan Africa. Sexually active HIV-positive adults were enrolled in 18 HIV clinics in Kenya, Namibia and Tanzania. Demographic, clinical and reproductive health data were captured by interview and medical record abstraction. Correlates of desiring a pregnancy within the next 6 months, and dual method use [defined as consistent condom use together with a highly effective method of contraception (hormonal, intrauterine device (IUD), permanent)], among those not desiring pregnancy, were identified using logistic regression. Among 3375 participants (median age 37 years, 42% male, 64% on antiretroviral treatment), 565 (17%) desired a pregnancy within the next 6 months. Of those with no short-term fertility desire (n=2542), 686 (27%) reported dual method use, 250 (10%) highly effective contraceptive use only, 1332 (52%) condom use only, and 274 (11%) no protection. Respondents were more likely to desire a pregnancy if they were from Namibia and Tanzania, male, had a primary education, were married/cohabitating, and had fewer children. Factors associated with increased likelihood of dual method use included being female, being comfortable asking a partner to use a condom, and communication with a health care provider about family planning. Participants who perceived that their partner wanted a pregnancy were less likely to report dual method use. There was low dual method use and low use of highly effective contraception. Contraceptive protection was predominantly through condom-only use. These findings demonstrate the importance of integrating reproductive health services into routine HIV care. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Investigation on Effect of Material Hardness in High Speed CNC End Milling Process.

PubMed

Dhandapani, N V; Thangarasu, V S; Sureshkannan, G

2015-01-01

This research paper analyzes the effects of material properties on surface roughness, material removal rate, and tool wear on high speed CNC end milling process with various ferrous and nonferrous materials. The challenge of material specific decision on the process parameters of spindle speed, feed rate, depth of cut, coolant flow rate, cutting tool material, and type of coating for the cutting tool for required quality and quantity of production is addressed. Generally, decision made by the operator on floor is based on suggested values of the tool manufacturer or by trial and error method. This paper describes effect of various parameters on the surface roughness characteristics of the precision machining part. The prediction method suggested is based on various experimental analysis of parameters in different compositions of input conditions which would benefit the industry on standardization of high speed CNC end milling processes. The results show a basis for selection of parameters to get better results of surface roughness values as predicted by the case study results.

Piezoresistive effect in p-type 3C-SiC at high temperatures characterized using Joule heating

PubMed Central

Phan, Hoang-Phuong; Dinh, Toan; Kozeki, Takahiro; Qamar, Afzaal; Namazu, Takahiro; Dimitrijev, Sima; Nguyen, Nam-Trung; Dao, Dzung Viet

2016-01-01

Cubic silicon carbide is a promising material for Micro Electro Mechanical Systems (MEMS) applications in harsh environ-ments and bioapplications thanks to its large band gap, chemical inertness, excellent corrosion tolerance and capability of growth on a Si substrate. This paper reports the piezoresistive effect of p-type single crystalline 3C-SiC characterized at high temperatures, using an in situ measurement method. The experimental results show that the highly doped p-type 3C-SiC possesses a relatively stable gauge factor of approximately 25 to 28 at temperatures varying from 300 K to 573 K. The in situ method proposed in this study also demonstrated that, the combination of the piezoresistive and thermoresistive effects can increase the gauge factor of p-type 3C-SiC to approximately 20% at 573 K. The increase in gauge factor based on the combination of these phenomena could enhance the sensitivity of SiC based MEMS mechanical sensors. PMID:27349378