Geometric and kinematic analysis of structural elements along north front of Bagharan Kuh Mountain, NE Iran

NASA Astrophysics Data System (ADS)

Samimi, S.; Gholami, E.

2017-03-01

At the end of the western part of Bagharan Kuh Mountain in the northeast of Iran, mountain growth has been stopped toward the west because of the stress having been consumed by the thrusting movements and region rising instead of shear movement. Chahkand fault zone is situated at the western part of this mountain; this fault zone includes several thrust sheets that caused upper cretaceous ophiolite rocks up to younger units, peridotite exposure and fault related fold developing in the surface. In transverse perpendicular to the mountain toward the north, reduction in the parameters like faults dip, amount of deformation, peridotite outcrops show faults growth sequence and thrust sheets growth from mountain to plain, thus structural vergence is toward the northeast in this fault zone. Deformation in the east part of the region caused fault propagation fold with axial trend of WNW-ESE that is compatible with trending of fault plane. In the middle part, two types of folds is observed; in the first type, folding occurred before faulting and folds was cut by back thrust activity; in the second type, faults activity caused fault related folds with N60-90W axial trend. In order to hanging wall strain balance, back thrusts have been developed in the middle and western part which caused popup and fault bend folds with N20-70E trend. Back thrusts activity formed footwall synclines, micro folds, foliations, and uplift in this part of the region. Kinematic analysis of faults show stress axis σ1 = N201.6, 7, σ2 = N292.6, 7.1, σ3 = N64.8, 79.5; stress axis obtained by fold analysis confirm that minimum stress (σ3) is close to vertical so it is compatible with fault analysis. Based on the results, deformation in this region is controlled by compressional stress regime. This stress state is consistent with the direction of convergence between the Arabian and Eurasian plates. Also study of transposition, folded veins, different movements on the fault planes and back thrusts confirm the progressive deformation is dominant in this region that it increases from the east to the west.

'Passive-roof' duplex geometry in the frontal structures of the Kirthar and Sulaiman mountain belts, Pakistan

NASA Astrophysics Data System (ADS)

Banks, C. J.; Warburton, J.

Exploration for hydrocarbons over the past few years has greatly improved our understanding of the geometry of frontal mountain belt structures. In this study we introduce and discuss the concept of the 'Passive-roof duplex', using as the main example the Kirthar and Sulaiman Ranges in the Baluchistan Province of Pakistan. Structures similar to those described here have been recognized previously in other mountain belts, and they appear to exist as a common feature in many more frontal regions of mountain belts. Our example of a Passive-roof duplex which we describe from Pakistan is compared briefly with similar structures reported by others. The Passive-roof duplex is here defined as a duplex whose roof thrust has backthrust sense ( Passive-roof thrust) and whose roof sequence (those rocks lying above the roof thrust) remains relatively 'stationary' during foreland directed piggy-back style propagation of horses within the duplex.

Transverse tectonic structural elements across Himalayan mountain front, eastern Arunachal Himalaya, India: Implication of superposed landform development on analysis of neotectonics

NASA Astrophysics Data System (ADS)

Bhakuni, S. S.; Luirei, Khayingshing; Kothyari, Girish Ch.; Imsong, Watinaro

2017-04-01

Structural and morphotectonic signatures in conjunction with the geomorphic indices are synthesised to trace the role of transverse tectonic features in shaping the landforms developed along the frontal part of the eastern Arunachal sub-Himalaya. Mountain front sinuosity (Smf) index values close to one are indicative of the active nature of the mountain front all along the eastern Arunachal Himalaya, which can be directly attributed to the regional uplift along the Himalayan Frontal Thrust (HFT). However, the mountain front is significantly sinusoidal around junctions between HFT/MBT (Main Boundary Thrust) and active transverse faults. The high values of stream length gradient (SL) and stream steepness (Ks) indices together with field evidence of fault scarps, offset of terraces, and deflection of streams are markers of neotectonic uplift along the thrusts and transverse faults. This reactivation of transverse faults has given rise to extensional basins leading to widening of the river courses, providing favourable sites for deposition of recent sediments. Tectonic interactions of these transverse faults with the Himalayan longitudinal thrusts (MBT/HFT) have segmented the mountain front marked with varying sinuosity. The net result is that a variety of tectonic landforms recognized along the mountain front can be tracked to the complex interactions among the transverse and longitudinal tectonic elements. Some distinctive examples are: in the eastern extremity of NE Himalaya across the Dibang River valley, the NW-SE trending mountain front is attenuated by the active Mishmi Thrust that has thrust the Mishmi crystalline complex directly over the alluvium of the Brahmaputra plains. The junction of the folded HFT and Mishmi Thrust shows a zone of brecciated and pulverized rocks along which transverse axial planar fracture cleavages exhibit neotectonic activities in a transverse fault zone coinciding with the Dibang River course. Similarly, the transverse faults cut the mountain front along the Sesseri, Siluk, Siku, Siang, Mingo, Sileng, Dikari, and Simen rivers. At some such junctions, landforms associated with the active right-lateral strike-slip faults are superposed over the earlier landforms formed by transverse normal faults. In addition to linear transverse features, we see evidence that the fold-thrust belt of the frontal part of the Arunachal Himalaya has also been affected by the neotectonically active NW-SE trending major fold known as the Siang antiform that again is aligned transverse to the mountain front. The folding of the HFT and MBT along this antiform has reshaped the landscape developed between its two western and eastern limbs running N-S and NW-SE, respectively. The transverse faults are parallel to the already reported deep-seated transverse seismogenic strike-slip fault. Therefore, a single take home message is that any true manifestation of the neotectonics and seismic hazard assessment in the Himalayan region must take into account the role of transverse tectonics.

Constraints on the tectonics of the Mule Mountains thrust system, southeast California and southwest Arizona

USGS Publications Warehouse

Tosdal, R.M.

1990-01-01

The Mule Mountains thrust system crops out discontinuously over a 100-km-strike length in this Blythe-Quartzsite region. Along the thrust system, middle and upper crustal metamorphic and plutonic rocks of Proterozoic and Mesozoic age are thrust N-NE (015??-035??) over a lower plate metamorphic terrane. Stratigraphic, petrologic, and Pb isotopic ties for Jurassic granitoids and for Jurassic(?) and Cretaceous sedimentary rocks across the various parts of the thrust system indicate that related crustal blocks are superposed and preclude it from having large displacements. Deformation occurred under low greenschist facies metamorphic conditions in the upper crust. Movement along the thrust system was probably limited to no more than a few tens of kilometers and occurred between 79??2 Ma and 70??4 Ma. Results suggest that the thrust system forms the southern boundary of the narow zone of Cretaceous intracratonic deformation, and it is one of the last tectonic events in the zone prior to regional cooling. -from Author

The age of the Keystone thrust: laser-fusion 40Ar/39Ar dating of foreland basin deposits, southern Spring Mountains, Nevada

USGS Publications Warehouse

Fleck, R.J.; Carr, M.D.

1990-01-01

Nonmarine sedimentary and volcaniclastic foreland-basin deposits in the Spring Mountains are cut by the Contact and Keystone thrusts. These synorogenic deposits, informally designated the Lavinia Wash sequence by Carr (1980), previously were assigned a Late Jurassic to Early Cretaceous(?) age. New 40Ar.39Ar laser-fusion and incremental-heating studies of a tuff bed in the Lavinia Wash sequence support a best estimate age of 99.0 ?? 0.4 Ma, indicating that the Lavinia Wash sequence is actually late Early Cretaceous in age and establishing a maximum age for final emplacement of the Contact and Keystone thrust plates consistent with the remainder of the Mesozoic foreland thrust belt. -from Authors

Duplex development and abandonment during evolution of the Lewis thrust system, southern Glacier National Park, Montana

NASA Astrophysics Data System (ADS)

Yin, An; Kelty, Thomas K.; Davis, Gregory A.

1989-09-01

Geologic mapping in southern Glacier National Park, Montana, reveals the presence of two duplexes sharing the same floor thrust fault, the Lewis thrust. The westernmost duplex (Brave Dog Mountain) includes the low-angle Brave Dog roof fault and Elk Mountain imbricate system, and the easternmost (Rising Wolf Mountain) duplex includes the low-angle Rockwell roof fault and Mt. Henry imbricate system. The geometry of these duplexes suggests that they differ from previously described geometric-kinematic models for duplex development. Their low-angle roof faults were preexisting structures that were locally utilized as roof faults during the formation of the imbricate systems. Crosscutting of the Brave Dog fault by the Mt. Henry imbricate system indicates that the two duplexes formed at different times. The younger Rockwell-Mt. Henry duplex developed 20 km east of the older Brave Dog-Elk Mountain duplex; the roof fault of the former is at a higher structural level. Field relations confirm that the low-angle Rockwell fault existed across the southern Glacier Park area prior to localized formation of the Mt. Henry imbricate thrusts beneath it. These thrusts kinematically link the Rockwell and Lewis faults and may be analogous to P shears that form between two synchronously active faults bounding a simple shear system. The abandonment of one duplex and its replacement by another with a new and higher roof fault may have been caused by (1) warping of the older and lower Brave Dog roof fault during the formation of the imbricate system (Elk Mountain) beneath it, (2) an upward shifting of the highest level of a simple shear system in the Lewis plate to a new decollement level in subhorizontal belt strata (= the Rockwell fault) that lay above inclined strata within the first duplex, and (3) a reinitiation of P-shear development (= Mt. Henry imbricate faults) between the Lewis thrust and the subparallel, synkinematic Rockwell fault.

Limited fluid in carbonate-shale hosted thrust faults of the Rocky Mountain Fold-and-Thrust Belt (Sun River Canyon, Montana)

NASA Astrophysics Data System (ADS)

OBrien, V. J.; Kirschner, D. L.

2001-12-01

It is widely accepted that fluids play a fundamental role in the movement of thrust faults in foreland fold-and-thrust belts. We have begun a combined structure-geochemistry study of faults in the Rocky Mountain fold-and-thrust belt in order to provide more insight into the occurrence and role(s) of fluid in the deformation of thrust faults. We focus on faults exposed in the Sun River Canyon of Montana, an area that contains some of the best exposures of the Rocky Mountain fold-and-thrust belt in the U.S. Samples were collected from two well exposed thrusts in the Canyon -- the Diversion and French thrusts. Both faults have thrust Mississippian dolostones over Cretaceous shales. Displacement exceeds several kilometers. Numerous small-displacement, subsidiary faults characterize the deformation in the hanging wall carbonates. The footwall shales accommodated more penetrative deformation, resulting in well developed foliation and small-scale folds. Stable isotope data have been obtained from host rock samples and veins from these faults. The data delimit an arcuate trend in oxygen-carbon isotope space. Approximately 50 host rock carbonate samples from the hanging walls have carbon and oxygen isotope values ranging from +3 to 0 and 28 to 19 per mil, respectively. There is no apparent correlation between isotopic values and distance from thrust fault at either locality. Fifteen samples of fibrous slickensides on small-displacement faults in the hanging walls have similar carbon and lower oxygen isotope values (down to 16 per mil). And 15 veins that either post-date thrusting or are of indeterminate origin have carbon and oxygen isotope values down to -3 and12 per mil, respectively. The isotopic data collected during the initial stages of this project are similar to some results obtained several hundred kilometers north in the Front Ranges of the Canadian Rockies (Kirschner and Kennedy, JGR 2000) and in carbonate fold-thrust belts of the Swiss Helvetic Alps and Italian Apennines. These data are consistent with limited infiltration of fluid through fractures and minor faults into hanging walls of large-displacement thrust faults.

Understanding continental megathrust earthquake potential through geological mountain building processes: an example in Nepal Himalaya

NASA Astrophysics Data System (ADS)

Zhang, Huai; Zhang, Zhen; Wang, Liangshu; Leroy, Yves; shi, Yaolin

2017-04-01

How to reconcile continent megathrust earthquake characteristics, for instances, mapping the large-great earthquake sequences into geological mountain building process, as well as partitioning the seismic-aseismic slips, is fundamental and unclear. Here, we scope these issues by focusing a typical continental collisional belt, the great Nepal Himalaya. We first prove that refined Nepal Himalaya thrusting sequences, with accurately defining of large earthquake cycle scale, provide new geodynamical hints on long-term earthquake potential in association with, either seismic-aseismic slip partition up to the interpretation of the binary interseismic coupling pattern on the Main Himalayan Thrust (MHT), or the large-great earthquake classification via seismic cycle patterns on MHT. Subsequently, sequential limit analysis is adopted to retrieve the detailed thrusting sequences of Nepal Himalaya mountain wedge. Our model results exhibit apparent thrusting concentration phenomenon with four thrusting clusters, entitled as thrusting 'families', to facilitate the development of sub-structural regions respectively. Within the hinterland thrusting family, the total aseismic shortening and the corresponding spatio-temporal release pattern are revealed by mapping projection. Whereas, in the other three families, mapping projection delivers long-term large (M<8)-great (M>8) earthquake recurrence information, including total lifespans, frequencies and large-great earthquake alternation information by identifying rupture distances along the MHT. In addition, this partition has universality in continental-continental collisional orogenic belt with identified interseismic coupling pattern, while not applicable in continental-oceanic megathrust context.

Reinterpretation of Mesozoic and Cenozoic tectonic events, Mountain Pass area, northeastern San Bernardino County, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nance, M.A.

1993-04-01

Detailed mapping, stratigraphic structural analysis in the Mountain Pass area has resulted in a reinterpretation of Mesozoic and Cenozoic tectonic events in the area. Mesozoic events are characterized by north vergent folds and thrust faults followed by east vergent thrusting. Folding created two synclines and an anticline which were than cut at different stratigraphic levels by subsequent thrust faults. Thrusting created composite tectono-stratigraphic sections containing autochthonous, para-autothonous, and allochthonous sections. Normal faults cutting these composite sections including North, Kokoweef, White Line, and Piute fault must be post-thrusting, not pre-thrusting as in previous interpretations. Detailed study of these faults results inmore » differentiation of at least three orders of faults and suggest they represent Cenozoic extension correlated with regional extensional events between 11 and 19 my. Mesozoic stratigraphy reflects regional orogenic uplift, magmatic activity, and thrusting. Inclusion of Kaibab clasts in the Chinle, Kaibab and Chinle clasts in the Aztec, and Chinle, Aztec, and previously deposited Delfonte Volcanics clasts in the younger members of the Delfonte Volcanics suggest regional uplift prior to the thrusting of Cambrian Bonanza King over Delfonte Volcanics by the Mescal Thrust fault. The absence of clasts younger than Kaibab argues against pre-thrusting activity for the Kokoweef fault.« less

Coseismic and blind fault of the 2015 Pishan Mw 6.5 earthquake: Implications for the sedimentary-tectonic framework of the western Kunlun Mountains, northern Tibetan Plateau

NASA Astrophysics Data System (ADS)

Lu, Renqi; Xu, Xiwei; He, Dengfa; Liu, Bo; Tan, Xibin; Wang, Xiaoshan

2016-04-01

On 3 July 2015, the Mw 6.5 Pishan earthquake occurred in the western Kunlun Mountains front, at the northern margin of the Tibetan Plateau. To reveal the sedimentary-tectonic framework of the seismically active structure, three high-resolution seismic reflection profiles and well drilling data were collected for seismic interpretation. The western Kunlun Mountains and Tarim Basin have two gypseous detachments and one basement detachment that control the tectonic framework and structural deformation. The upper gypseous detachment (D1) is in the lower Paleocene, and the middle gypseous detachment (D2) is in the Middle to Lower Cambrian. A Neogene shallow thrust system is developing above D1 and includes the Zepu fault (F2) and Mazar Tagh fault (F3). A deep thrust system is developing between D1 and D2 and forms a large-scale structural wedge beneath the western Kunlun Mountains front. The Pishan Mw 6.5 earthquake was triggered on a frontal blind fault of this deep thrust system. The lower detachment is in the Proterozoic basement (D3), which extends into the Tarim Basin and develops another deep thrust (F4) beneath the F3 belt. D1, D2, D3, and the Tiekelike fault (F1) merge together at depth. Crustal shortening of the western Kunlun Mountains front continues for approximately 54 km. Two tectonic evolutionary stages have occurred since the Miocene according to sedimentary unconformity, axial analysis, and fault interpretation. The results of this study indicate a regime of episodic growth of the western Kunlun Mountains and Tarim Basin during the Cenozoic.

Hazard evaluation of inorganics, singly and in mixtures, to Flannelmouth Sucker Catostomus latipinnis in the San Juan River, New Mexico

USGS Publications Warehouse

Hamilton, S.J.; Buhl, K.J.

1997-01-01

Larval flannelmouth sucker (Catostomus latipinnis) were exposed to arsenate, boron, copper, molybdenum, selenate, selenite, uranium, vanadium, and zinc singly, and to five mixtures of five to nine inorganics. The exposures were conducted in reconstituted water representative of the San Juan River near Shiprock, New Mexico. The mixtures simulated environmental ratios reported for sites along the San Juan River (San Juan River backwater, Fruitland marsh, Hogback East Drain, Mancos River, and McElmo Creek). The rank order of the individual inorganics, from most to least toxic, was: copper > zinc > vanadium > selenite > selenate > arsenate > uranium > boron > molybdenum. All five mixtures exhibited additive toxicity to flannelmouth sucker. In a limited number of tests, 44-day-old and 13-day-old larvae exhibited no difference in sensitivity to three mixtures. Copper was the major toxic component in four mixtures (San Juan backwater, Hogback East Drain, Mancos River, and McElmo Creek), whereas zinc was the major toxic component in the Fruitland marsh mixture, which did not contain copper. The Hogback East Drain was the most toxic mixture tested. Comparison of 96-h LC50values with reported environmental water concentrations from the San Juan River revealed low hazard ratios for arsenic, boron, molybdenum, selenate, selenite, uranium, and vanadium, moderate hazard ratios for zinc and the Fruitland marsh mixture, and high hazard ratios for copper at three sites and four environmental mixtures representing a San Juan backwater, Hogback East Drain, Mancos River, and McElmo Creek. The high hazard ratios suggest that inorganic contaminants could adversely affect larval flannelmouth sucker in the San Juan River at four sites receiving elevated inorganics.

Steady evolution of hillslopes in layered landscapes: self-organization of a numerical hogback

NASA Astrophysics Data System (ADS)

Glade, R.; Anderson, R. S.

2017-12-01

Landscapes developed in layered sedimentary or igneous rocks are common across Earth, as well as on other planets. Features such as hogbacks, exposed dikes, escarpments and mesas exhibit resistant rock layers in tilted, vertical, or horizontal orientation­s adjoining more erodible rock. Hillslopes developed in the erodible rock are typically characterized by steep, linear-to-concave slopes or "ramps" mantled with material derived from the resistant layers, often in the form of large blocks. Our previous work on hogbacks has shown that feedbacks between weathering and transport of the blocks and underlying soft rock are fundamental to their formation; our numerical model incorporating these feedbacks explain the development of commonly observed concave-up slope profiles in the absence of rilling processes. Here we employ an analytic approach to describe the steady behavior of our model, in which hillslope form and erosion rates remain constant in the reference frame of the retreating feature. We first revisit a simple geometric analysis that relates structural dip to erosion rates. We then explore the mechanisms by which our numerical model of hogback evolution self-organizes to meet these geometric expectations. Autogenic adjustment of soil depth, slope and erosion rates enables efficient transport of resistant blocks; this allows erosion of the resistant layer to keep up with base level fall rate, leading to steady evolution of the feature. Analytic solutions relate easily measurable field quantities such as ramp length, slope, block size and resistant layer dip angle to local incision rate, block velocity, and block weathering rate. These equations provide a framework for exploring the evolution of layered landscapes, and pinpoint the processes for which we require a more thorough understanding to predict the evolution of such signature landscapes over time.

The Junction of Hellenic and Cyprus Arcs: a Detailed Study of the Morphology and Neogene Tectonic Evolution of the Anaximander Mountains

NASA Astrophysics Data System (ADS)

Cranshaw, J.; Aksu, A.; Hall, J.; Cifci, G.; Dondurur, D.; Yaltirak, C.

2009-05-01

The Anaximander Mountains are enigmatic highs located at the complex corner that links the Cyprus and Hellenic Arcs in the eastern Mediterranean. They are made up of several different highs: Anaximander (sensu stricto), Anaxagoras and Anaximenes. Previous work had shown that rock samples from the Anaximander Mountain have affinity with rocks exposed on land nearby in southern Turkey. This had been explained by rifting of the Mountain away from Turkey. In contrast to that, our interpretation of around 1750 km of high-resolution multi-channel seismic reflection data acquired in 2001 showed that Anaximander Mountain is part of a broadly south-verging Miocene thrust system associated with relative southward motion of the Tauride Mountains in southern Turkey. Post-Miocene motion also involves thrusting but is accompanied by transpression and rotation. The 3-dimensional nature of the geology makes mapping of the linkage of structures difficult, so we collected an additional 500 km of multi-channel seismic reflection data acquired in 2007, extending our 2001 survey further southwards into the Mediterranean Ridge. These new profiles are shot in a grid oblique to that obtained in 2001, such that the new profile intersections provide a basis for better correlation of the earlier data. We are testing our earlier interpretation through processing and interpretation of these new profiles. Here, we present examples of the new profiles and give first indications of how our earlier interpretation is broadly corroborated by the new data, but with minor adjustments. Anaximenes Mountain is imaged to the south of our previously- mapped area and is characterized as a large south-verging thrust lifting pre-Messinian strata by up to 2 km in a 12-km wide pop-up structure. Internally, Anaximenes is dissected by several splays from the bounding thrusts.

The junction of Hellenic and Cyprus arcs: a detailed study of the morphology and Neogene tectonic evolution of the Anaximander Mountains

NASA Astrophysics Data System (ADS)

Cranshaw, J.; Aksu, A.; Hall, J.; Çifçi, G.; Dondurur, D.; Yaltırak, C.

2009-04-01

The Anaximander Mountains are enigmatic highs located at the complex corner that links the Cyprus and Hellenic Arcs in the eastern Mediterranean. They are made up of several different highs: Anaximander (sensu stricto), Anaxagoras and Anaximenes. Previous work had shown that rock samples from the Anaximander Mountain have affinity with rocks exposed on land nearby in southern Turkey. This had been explained by rifting of the Mountain away from Turkey. In contrast to that, our interpretation of around 1750 km of high-resolution multi-channel seismic reflection data acquired in 2001 showed that Anaximander Mountain is part of a broadly south-verging Miocene thrust system associated with relative southward motion of the Tauride Mountains in southern Turkey. Post-Miocene motion also involves thrusting but is accompanied by transpression and rotation. The 3-dimensional nature of the geology makes mapping of the linkage of structures difficult, so we collected an additional 500 km of multi-channel seismic reflection data acquired in 2007, extending our 2001 survey further southwards into the Mediterranean Ridge. These new profiles are shot in a grid oblique to that obtained in 2001, such that the new profile intersections provide a basis for better correlation of the earlier data. We are testing our earlier interpretation through processing and interpretation of these new profiles. Here, we present examples of the new profiles and give first indications of how our earlier interpretation is broadly corroborated by the new data, but with minor adjustments. Anaximenes Mountain is imaged to the south of our previously-mapped area and is characterized as a large south-verging thrust lifting pre-Messinian strata by up to 2 km in a 12-km wide pop-up structure. Internally, Anaximenes is dissected by several splays from the bounding thrusts.

Paleomagnetic, structural, and seismological evidence for oblique-slip deformation in fault-related folds in the Rocky Mountain Foreland, Colorado Plateau, and central Coast Ranges

NASA Astrophysics Data System (ADS)

Tetreault, Joya Liana

The two geologic questions I address in this research are: do fault-related folds accommodate oblique-slip shortening, and how is oblique-slip deformation absorbed within the folded strata? If the strata is deforming as a strike-slip shear zone, then we should be able to observe material rotations produced by strike-slip shear by measuring paleomagnetic vertical-axis rotations. I have approached these problems by applying paleomagnetic vertical-axis rotations, minor fault analyses, and focal mechanism strain inversions to identify evidence of strike-slip shear and to quantify oblique-slip deformation within fault-related folds in the Rocky Mountain Foreland, Colorado Plateau, and the central Coast Ranges. Clockwise paleomagnetic vertical-axis rotations and compressive paleostress rotations of 15-40º in the forelimb of the Grayback Monocline, northeastern Front Range Colorado, indicate that this Laramide fold is absorbing right-lateral shear from a N90E regional shortening direction. This work shows that paleomagnetic vertical-axis rotations in folded strata can be used to identify strike-slip motion on an underlying fault, and that oblique-slip deformation is localized in the forelimb of the fold. I applied the same paleomagnetic methods to identify oblique-slip on the underlying faults of the Nacimiento, East Kaibab, San Rafael, and Grand Hogback monoclines of the Colorado Plateau. The absence of paleomagnetic rotations and structural evidence for small displacements at the Nacimiento and East Kaibab monoclines indicate minor (<1km) right-lateral slip is being accommodated in these folds. Paleomagnetic vertical-axis rotations are found in the forelimbs of the San Rafael and Grand Hogback monoclines, yielding strike-slip displacements of ˜5km within these two folds. These results are consistent with a northeast Laramide compressive stress direction. In the Coalinga anticline, central Coast Ranges, California, clockwise paleomagnetic rotations and an 8º counterclockwise deflection of the maximum shortening direction (derived from focal mechanisms strain inversions of the upper 7km) are compatible with right-lateral shear. The maximum shortening direction in the area of the mainshock rupture is fold-normal, indicating that strike-slip displacement is confined to the main fault plane and not distributed to the hanging wall. The San Andreas Fault is therefore partitioning a small amount of strike-slip to the Coalinga anticline.

New Insight into the Role of Tectonics versus Gravitational Deformation in Development of Surface Ruptures along the Ragged Mountain Fault, Katalla, Alaska USA: Applications of High-Resolution Three-Dimensional Terrain Models

NASA Astrophysics Data System (ADS)

Heinlein, S. N.; Pavlis, T. L.; Bruhn, R. L.; McCalpin, J. P.

2017-12-01

This study evaluates a surface structure using 3D visualization of LiDAR and aerial photography then analyzes these datasets using structure mapping techniques. Results provide new insight into the role of tectonics versus gravitational deformation. The study area is located in southern Alaska in the western edge of the St. Elias Orogen where the Yakutat microplate is colliding into Alaska. Computer applications were used to produce 3D terrain models to create a kinematic assessment of the Ragged Mountain fault which trends along the length of the east flank of Ragged Mountain. The area contains geomorphic and structural features which are utilize to determine the type of displacement on the fault. Previous studies described the Ragged Mountain fault as a very shallow (8°), west-dipping thrust fault that reactivated in the Late Holocene by westward-directed gravity sliding and inferred at least 180 m of normal slip, in a direction opposite to the (relative) eastward thrust transport of the structure inferred from stratigraphic juxtaposition. More recently this gravity sliding hypothesis has been questioned and this study evaluates one of these alternative hypotheses; that uphill facing normal fault-scarps along the Ragged Mountain fault trace represent extension above a buried ramp in a thrust and is evaluated with a fault-parallel flow model of hanging-wall folding and extension. Profiles across the scarp trace were used to illustrate the curvature of the topographic surfaces adjacent to the scarps system and evaluate their origin. This simple kinematic model tests the hypothesis that extensional fault scarps at the surface are produced by flexure above a deeper ramp in a largely blind thrust system. The data in the context of this model implies that the extensional scarp structures previously examined represent a combination of erosionally modified features overprinted by flexural extension above a thrust system. Analyses of scarp heights along the structure are combined with the model to suggest a decrease in Holocene slip from south to north along the Ragged Mountain fault from 11.3 m to 0.2 m, respectively.

Formation of fold-and-thrust belts on Venus by thick-skinned deformation

NASA Astrophysics Data System (ADS)

Zuber, M. T.; Parmentier, E. M.

1995-10-01

ON Venus, fold-and-thrust belts—which accommodate large-scale horizontal crustal convergence—are often located at the margins of kilometre-high plateaux1-5. Such mountain belts, typically hundreds of kilometres long and tens to hundreds of kilometres wide, surround the Lakshmi Planum plateau in the Ishtar Terra highland (Fig. 1). In explaining the origin of fold-and-thrust belts, it is important to understand the relative importance of thick-skinned deformation of the whole lithosphere and thin-skinned, large-scale overthrusting of near-surface layers. Previous quantitative analyses of mountain belts on Venus have been restricted to thin-skinned models6-8, but this style of deformation does not account for the pronounced topographic highs at the plateau edge. We propose that the long-wavelength topography of these venusian fold-and-thrust belts is more readily explained by horizontal shortening of a laterally heterogeneous lithosphere. In this thick-skinned model, deformation within the mechanically strong outer layer of Venus controls mountain building. Our results suggest that lateral variations in either the thermal or mechanical structure of the interior provide a mechanism for focusing deformation due to convergent, global-scale forces on Venus.

Geologic map of the Storm King Mountain quadrangle, Garfield County, Colorado

USGS Publications Warehouse

Bryant, Bruce; Shroba, Ralph R.; Harding, Anne E.; Murray, Kyle E.

2002-01-01

New 1:24,000-scale geologic mapping in the Storm King Mountain 7.5' quadrangle, in support of the USGS Western Colorado I-70 Corridor Cooperative Geologic Mapping Project, provides new data on the structure on the south margin of the White River uplift and the Grand Hogback and on the nature, history, and distribution of surficial geologic units. Rocks ranging from Holocene to Proterozoic in age are shown on the map. The Canyon Creek Conglomerate, a unit presently known to only occur in this quadrangle, is interpreted to have been deposited in a very steep sided local basin formed by dissolution of Pennsylvanian evaporite late in Tertiary time. At the top of the Late Cretaceous Williams Fork Formation is a unit of sandstone, siltstone, and claystone from which Late Cretaceous palynomorphs were obtained in one locality. This interval has been mapped previously as Ohio Creek Conglomerate, but it does not fit the current interpretation of the origin of the Ohio Creek. Rocks previously mapped as Frontier Sandstone and Mowry Shale are here mapped as the lower member of the Mancos Shale and contain beds equivalent to the Juana Lopez Member of the Mancos Shale in northwestern New Mexico. The Pennsylvanian Eagle Valley Formation in this quadrangle grades into Eagle Valley Evaporite as mapped by Kirkham and others (1997) in the Glenwood Springs area. The Storm King Mountain quadrangle spans the south margin of the White River uplift and crosses the Grand Hogback monocline into the Piceance basin. Nearly flat lying Mississippian through Cambrian sedimentary rocks capping the White River uplift are bent into gentle south dips and broken by faults at the edge of the uplift. South of these faults the beds dip moderately to steeply to the south and are locally overturned. These dips are interrupted by a structural terrace on which are superposed numerous gentle minor folds and faults. This terrace has an east-west extent similar to that of the Canyon Creek Conglomerate to the north. We interpret that the terrace formed by movement of Eagle Evaporite from below in response to dissolution and diapirism in the area underlain by the conglomerate. A low-angle normal fault dipping gently north near the north margin of the quadrangle may have formed also in response to diapirism and dissolution in the area of the Canyon Creek Conglomerate. Along the east edge of the quadrangle Miocene basalt flows are offset by faults along bedding planes in underlying south-dipping Cretaceous rocks, probably because of diapiric movement of evaporite into the Cattle Creek anticline (Kirkham and Widmann, 1997). Steep topography and weak rocks combine to produce a variety of geologic hazards in the quadrangle.

Geologic map of the Skull Creek Quadrangle, Moffat County Colorado

USGS Publications Warehouse

Van Loenen, R. E.; Selner, Gary; Bryant, W.A.

1999-01-01

The Skull Creek quadrangle is in northwestern Colorado a few miles north of Rangely. The prominent structural feature of the Skull Creek quadrangle is the Skull Creek monocline. Pennsylvanian rocks are exposed along the axis of the monocline while hogbacks along its southern flank expose rocks that are from Permian to Upper Cretaceous in age. The Wolf Creek monocline and the Wolf Creek thrust fault, which dissects the monocline, are salient structural features in the northern part of the quadrangle. Little or no mineral potential exists within the quadrangle. A geologic map of the Lazy Y Point quadrangle, which is adjacent to the Skull Creek quadrangle on the west, is also available (Geologic Investigations Series I-2646). This companian map shows similar geologic features, including the western half of the Skull Creek monocline. The geology of this quadrangle was mapped because of its proximity to Dinosaur National Monument. It is adjacent to quadrangles previously mapped to display the geology of this very scenic and popular National Monument. The Skull Creek quadrangle includes parts of the Skull Creek Wilderness Study Area, which was assessed for its mineral resource potential.

Constraints on the tectonics of the Mule Mountains Thrust System, southeast California and southwest Arizona

NASA Astrophysics Data System (ADS)

Tosdal, Richard M.

1990-11-01

The Mule Mountains thrust system crops out discontinuously over a 100-km-strike length in the Blythe-Quartzsite region of southeast California and southwest Arizona. Along the thrust system, middle and upper crustal metamorphic and plutonic rocks of Proterozoic and Mesozoic age are thrust north-northeastward (015° to 035°) over a lower plate metamorphic terrane that formed part of the Proterozoic North American craton, its Paleozoic sedimentary rock cover, overlying Mesozoic volcanic and sedimentary rocks, and the intruding Jurassic and Cretaceous granitic rocks. Stratigraphic, petrologic, and Pb isotopic ties for Jurassic granitoids and for Jurassic(?) and Cretaceous sedimentary rocks across the various parts of the thrust system indicate that related crustal blocks are superposed and preclude it from having large displacements. The thick-skinned thrust system is structurally symmetrical along its length with a central domain of synmetamorphic thrust faults that are flanked by western and eastern domains where lower plate synclines underlie the thrusts. Deformation occurred under low greenschist facies metamorphic conditions in the upper crust. Movement along the thrust system was probably limited to no more than a few tens of kilometers and occurred between 79±2 Ma and 70±4 Ma. The superposition of related rocks and the geometry of the thrust system preclude it from being a major tectonic boundary of post-Middle Jurassic age, as has been previously proposed. Rather, the thrust system forms the southern boundary of the narrow zone of Cretaceous intracratonic deformation, and it is one of the last tectonic events in the zone prior to regional cooling.

Structural framework of a major intracontinental orogenic termination zone: The easternmost Tien Shan, China

USGS Publications Warehouse

Cunningham, D.; Owen, L.A.; Snee, L.W.; Li, Ji

2003-01-01

The Barkol Tagh and Karlik Tagh ranges of the easternmost Tien Shan are a natural laboratory for studying the fault architecture of an active termination zone of a major intracontinental mountain range. Barkol and Karlik Tagh and lesser ranges to the north are bounded by active thrust faults that locally deform Quaternary sediments. Major thrusts in Karlik Tagh connect along strike to the east with the left-lateral Gobi-Tien Shan Fault System in SW Mongolia. From a Mongolian perspective. Karlik Tagh represents a large restraining bend for this regional strike-slip fault system, and the entire system of thrusts and strike-slip faults in the Karlik Tagh region defines a horsetail splay fault geometry. Regionally, there appears to be a kinematic transition from thrust-dominated deformation in the central Tien Shan to left-lateral transpressional deformation in the easternmost Tien Shan. This transition correlates with a general eastward decrease in mountain belt width and average elevation and a change in the angular relationship between the NNE-directed maximum horizontal stress in the region and the pre-existing basement structural grain, which is northwesterly in the central Tien Shan (orthogonal to SHmax) but more east-west in the eastern Tien Shan (acute angular relationship with SHmax . Ar-Ar ages indicate that major range-bounding thrusts in Barkol and Karlik Tagh are latest Permian-Triassic ductile thrust zones that underwent brittle reactivation in the Late Cenozoic. It is estimated that the modern mountain ranges of the extreme easternmost Tien Shan could have been constructed by only 10-15 km of Late Cenozoic horizontal shortening.

Intrinsic And Extrinsic Controls On Unsteady Deformation Rates, Northern Apennine Mountains, Italy

NASA Astrophysics Data System (ADS)

Anastasio, D. J.; Gunderson, K. L.; Pazzaglia, F. J.; Kodama, K. P.

2017-12-01

The slip rates of faults in the Northern Apennine Mountains were unsteady at 104-105 year timescales during the Neogene and Quaternary. Fault slip rates were recovered from growth strata and uplifted fluvial terraces associated with the Salsomaggiore, Quatto Castella, and Castevetro fault-related folds, sampled along the Stirone, Enza, and Panaro Rivers, respectively. The forelimb stratigraphy of each anticline was dated using rock magnetic-based cyclostratigraphy, which varies with Milankovitch periodicity, multispecies biostratigraphy, magnetostratigraphy, OSL luminescence dating, TCN burial dating, and radiocarbon dating of uplifted and folded fluvial terraces. Fault slip magnitudes were constrained with trishear forward models. We observed decoupled deformation and sediment accumulation rates at each structure. From 3.5Ma deformation of a thick and thin-skinned thrusts was temporally variable and controlled by intrinsic rock processes, whereas, the more regional Pede-Apenninic thrust fault, a thick-skinned thrust underlying the mountain front, was likely activated because of extrinsic forcing from foreland basin sedimentation rate accelerations since 1.4Ma. We found that reconstructed slip rate variability increased as the time resolution increased. The reconstructed slip history of the thin-skinned thrust faults was characterized relatively long, slow fold growth and associated fault slip, punctuated by shorter, more rapid periods limb rotation, and slip on the underlying thrust fault timed asynchronously. Thrust fault slip rates slip rates were ≤ 0.1 to 6 mm/yr at these intermediate timescales. The variability of slip rates on the thrusts is likely related to strain partitioning neighboring faults within the orogenic wedge. The studied structures slowed down at 1Ma when there was a switch to slower synchronous fault slip coincident with orogenic wedge thickening due to the emplacement of the out of sequence Pene-Apenninic thrust fault that was emplaced at 1.4±0.7 mm/yr. Both tectonic control and climate controlled variability on syntectonic sedimentation was observed in the growth sections.

Effects of structural heterogeneity on frictional heating from biomarker thermal maturity analysis of the Muddy Mountain thrust, Nevada, USA

NASA Astrophysics Data System (ADS)

Coffey, G. L.; Savage, H. M.; Polissar, P. J.; Rowe, C. D.

2017-12-01

Faults are generally heterogeneous along-strike, with changes in thickness and structural complexity that should influence coseismic slip. However, observational limitations (e.g. limited outcrop or borehole samples) can obscure this complexity. Here we investigate the heterogeneity of frictional heating determined from biomarker thermal maturity and microstructural observations along a well-exposed fault to understand whether coseismic stress and frictional heating are related to structural complexity. We focus on the Muddy Mountain thrust, Nevada, a Sevier-age structure that has continuous exposure of its fault core and considerable structural variability for up to 50 m, to explore the distribution of earthquake slip and temperature rise along strike. We present new biomarker thermal maturity results that capture the heating history of fault rocks. Biomarkers are organic molecules produced by living organisms and preserved in the rock record. During heating, their structure is altered systematically with increasing time and temperature. Preliminary results show significant variability in thermal maturity along-strike at the Muddy Mountain thrust, suggesting differences in coseismic temperature rise on the meter- scale. Temperatures upwards of 500°C were generated in the principal slip zone at some locations, while in others, no significant temperature rise occurred. These results demonstrate that stress or slip heterogeneity occurred along the Muddy Mountain thrust at the meter-scale and considerable along-strike complexity existed, highlighting the importance of careful interpretation of whole-fault behavior from observations at a single point on a fault.

Constraints on the tectonics of the Mule Mountains thrust system, southeast California and southwest Arizona

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tosdal, R.M.

1990-11-10

The Mule Mountains thrust system crops out discontinuously over a 100-km-strike length in the Blythe-Quartzsite region of southeast California and southwest Arizona. Along the thrust system, middle and upper crustal metamorphic and plutonic rocks of Proterozoic and Mesozoic age are thrust north-northeastward (015{degree} to 035{degree}) over a lower plate metamorphic terrane that formed part of the Proterozoic North American craton, its Paleozoic sedimentary rock cover, overlying Mesozoic volcanic and sedimentary rocks, and the intruding Jurassic and Cretaceous granitic rocks. Stratigraphic, petrologic, and Pb isotopic ties for Jurassic granitoids and for Jurassic( ) and Cretaceous sedimentary rocks across the various partsmore » of the thrust system indicate that related crustal blocks are superposed and preclude it from having large displacements. The thick-skinned thrust system is structurally symmetrical along its length with a central domain of synmetamorphic thrust faults that are flanked by western and eastern domains where lower plate domains where lower plate synclines underlie the thrusts. Deformation occurred under low greenschist facies metamorphic conditions in the upper crust. Movement along the thrust system was probably limited to no more than a few tens of kilometers and occurred between 79{plus minus}2 Ma and 70{plus minus}4 Ma. The superposition of related rocks and the geometry of the thrust system preclude it from being a major tectonic boundary of post-Middle Jurassic age, as has been previously proposed. Rather, the thrust system forms the southern boundary of the narrow zone of Cretaceous intracratonic deformation, and it is one of the last tectonic events in the zone prior to regional cooling.« less

Boundary element analysis of active mountain building and stress heterogeneity proximal to the 2015 Nepal earthquake

NASA Astrophysics Data System (ADS)

Thompson, T. B.; Meade, B. J.

2015-12-01

The Himalayas are the tallest mountains on Earth with ten peaks exceeding 8000 meters, including Mt. Everest. The geometrically complex fault system at the Himalayan Range Front produces both great relief and great earthquakes, like the recent Mw=7.8 Nepal rupture. Here, we develop geometrically accurate elastic boundary element models of the fault system at the Himalayan Range Front including the Main Central Thrust, South Tibetan Detachment, Main Frontal Thrust, Main Boundary Thrust, the basal detachment, and surface topography. Using these models, we constrain the tectonic driving forces and frictional fault strength required to explain Quaternary fault slip rate estimates. These models provide a characterization of the heterogeneity of internal stress in the region surrounding the 2015 Nepal earthquake.

Integration of new geologic mapping and satellite-derived quartz mapping yields insights into the structure of the Roberts Mountains allochthon applicable to assessments for concealed Carlin-type gold deposits

USGS Publications Warehouse

Holm-Denoma, Christopher S.; Hofstra, Albert H.; Rockwell, Barnaby W.; Noble, Paula J.

2012-01-01

Geologic mapping and remote sensing across north-central Nevada enable recognition of a thick sheet of Middle and Upper Ordovician Valmy Formation quartzite that structurally overlies folded and faulted Ordovician through Devonian stratigraphic units of the Roberts Mountains allochthon. In the northern Independence Mountains and nearby Double Mountain area, the Valmy Formation is in fault contact with Ordovician through Silurian, predominantly clastic, sedimentary rocks of the Roberts Mountains allochthon that were deformed prior to, or during, emplacement of the Valmy thrust sheet. Similar structural relations are recognized discontinuously for 200 kilometers along the strike of the Roberts Mountains allochthon in mapping guided by regional remote-sensing-based (ASTER) quartz maps. Overall thicknesses of deformed Roberts Mountains allochthon units between the base of the Valmy and the top of underlying carbonate rocks that host large Carlin-type gold deposits varies on the order of hundreds of meters but is not known to exceed 700 meters. The base of the Valmy thrust sheet is a complimentary datum in natural resource exploration and mineral resource assessment for concealed Carlin-type gold deposits.

Foreland structure - Beartooth Mountains, Montana and Wyoming

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clark, D.M.

1996-06-01

Analysis of public drilling records from the AMOCO Beartooth Number 1 and 1 A sidetrack boreholes (SW1/4, SE1/4, Section 19, T.8 S., R.20 E., Carbon County, Montana) continues. Several additional inferences are made about this large foreland structure, and subsequent interpretation of the structural model of the northeast corner of the Beartooth Mountain Block and structural relationship with the Big Horn Basin. The structure is described as a large recumbent to sub-horizontal, synclinal fold with the overturned upper limb out diagonally by the Beartooth Thrust or Thrust Zone and a complex thrust fault zone below the Beartooth Thrust. The singlemore » recorded dip angle and direction of the Beartooth Thrust at depth was 19 degrees to the northwest(?). The dipmeter dip angle on the Beartooth Thrust, 19 degrees, validates foreland structural theory of decreasing dip angles at a vertical depth of 8,232 feet (2,509 m), in the Precambrian crystalline basement. The northwest dip direction may be attributable to secondary structural folding. The record of northwest, southeast, and southwest dip of bedding surfaces and faults in sections of the overturned upper limb, in both boreholes, suggests possible, less intense secondary folding, after thrust fault deformation. Given the overall geometry of this large foreland structure, there is little doubt that the average direction of maximum principal stress (sigma 1) was oriented in a northeast - southwest direction.« less

A geochemical investigation of selected areas in Greenville and Laurens counties, South Carolina--implications for mineral resources

USGS Publications Warehouse

Jackson, John C.

1992-01-01

The purpose of this study is to geochemically evaluate three areas within the Greenville 1° x 2° quadrangle (see index map) that have been shown by previous studies to contain anomalously high amounts of tin. Jackson and Moore (1992) reported the presence of cassiterite (SnO2)-bearing heavy-mineral concentrates from stream sediment samples that were collected during a regional geochemical reconnaissance of the Greenville 1° x 2° quadrangle. The data reported here confirm identified in selected heavy-mineral concentrate samples. In addition, anomalously high concentrations of barium, beryllium, lanthanum, and thorium are also reported for parts of the same areas. No significant mineral deposits are known to occur in the study areas. There was, however, minor production of monazite from several nearby localities (Sloan, 1908), and gold was produced from deposits in the northeastern part of Greenville County and nearby Spartanburg County (McCauley and Butler, 1966). The three areas selected for resampling are located in the Inner Piedmont physiographic province of South Carolina (see index map). The generalized tectonic setting of the region and the locations of the study is just north of Greenville, S.C. Much of it is within the moderately to steeply sloped terrane of Paris Mountain State Park where elevations reach approximately 600 m. Simpsonville, S.C., is neat the center of the second study area, and the southernmost study area is near Hickory Tavern, S.C. Both the Simpsonville and Hickory Tavern study areas are in more gently rolling Piedmont terrane. Each of the sampled areas is drained by tributaries of the Enoree and Reedy Rivers. Parts of three different thrust sheets underlie the region covered by this study (fig. 1); in ascending structural position, they are the Six Mile, Paris Mountain, and Laurens thrust sheets (Nelson and others, 1987). Nelson (1988, p. 7) described the contacts between these sheets as being along unnamed faults. The rocks in and around the study areas have undergone sillimanite-muscovite-grade metamorphism (Nelson, 1988, p. 9). Nelson (1988, p. 13) reports that the Six Mile thrust sheet was metamorphosed about 344 Ma. The geology of these sheets as described in this study, including geologic contacts, rock descriptions, and unit names, generally follows that of Nelson and others (1987, 1989). Within the Paris Mountain study area, rocks of the Paris Mountain thrust sheet predominate (fig. 2) and consist of a biotite-muscovite-sillimanite schist (EZsp) that has extensive lenses of fine- to medium- grained biotite granite gneiss (Pzgp). Areas of biotite granite gneiss that occur in the southern part of the Paris Mountain study area contain extensive pegmatitic and leucogranitic phases. These pegmatitic zones consist mostly of coarse-grained microcline feldspar and quartz with minor amounts of muscovite, biotite, and garnet. Smaller pegmatite lenses (<0.5 m thick) that occur within the biotite-muscovite-sillimanite schist of the Paris Mountain study area are generally of similar mineralogy, although some contain tourmaline crystals up to 5 cm in length. The Six Mile thrust sheet underlies the northern edge of the Paris Mountain study area, where it is composed of gneissic biotitic granites of the Caesars Head Granite (figs. 1 and 2). The northwestern part of the Simpsonville study area (figs. 1 and 3), within the Paris Mountain thrust sheet, is underlain by a biotite-muscovite-sillimanite schist (EZsp) that contains lenses of biotite granite gneiss (Pzgp). In the southeastern part of the Simpsonville study area, within the Laurens thrust sheet, biotite gneiss (EZgl), biotite granite gneiss (Pzgf), and minor amphibolite (EZal) are interlayered biotite (EZgl), granite gneiss (Dgg), and amphibolite (EZal) of the Laurens thrust sheet (fig. 4).

The role of Mesozoic sedimentary basin tapers on the formation of Cenozoic crustal shortening structures and foredeep in the western Sichuan Basin, China

NASA Astrophysics Data System (ADS)

Wang, M.

2017-12-01

The foreland basin records important clues of tectonic and sedimentary process of mountain-building, thus to explore its dynamic mechanism on the formation is an important issue of the mountain-basin interaction. The Longmen Shan fold-and-thrust belt and its adjacent Sichuan basin located in the eastern margin of Tibetan Plateau, are one of the most-concerned regions of studying modern mountain-building and seismic process, and are also a natural laboratory of studying the dynamics of the formation and development of foreland basin. However, it still need further explore on the mechanics of the development of the Cenozoic foreland basin and thrust-belts in the western Sichuan Basin. The Longmen Shan thrust belt has experienced multi-stages of tectonics evolution, foreland basin formation and topography growth since Late Triassic, and whether the early formed basin architecture and large Mesozoic sedimentary basin taper can influence the formation and development of the Cenozoic foreland basin and thrust belts? To solve these issues, this project aim to focus on the Cenozoic foreland basin and internal crustal shortening structures in the western Sichuan basin, on the basis of growth critical wedge taper theory. We will reconstruct the shape of multi-phases of sedimentary basin tapers, the temporal-spatial distribution of crustal shortening and thrusting sequences, and analyze the control mechanism of Mesozoic sedimentary basin taper on the formation of Cenozoic foreland basins, and final explore the interaction between the tectonics geomorphology, stress field and dynamic propagation of foreland basin.

Geology of the Mount Rogers area, revisited: Evidence of Neoproterozoic continental rifting, glaciation, and the opening and closing of the Iapetus ocean, Blue Ridge, VA–NC–TN

USGS Publications Warehouse

Merschat, Arthur J.; Southworth, C. Scott; Holm-Denoma, Christopher S.; McAleer, Ryan J.; Merschat, Arthur J.

2016-01-01

Recent field and geochronological studies in eight 7.5-minute quadrangles near Mount Rogers in Virginia, North Carolina and Tennessee recognize important stratigraphic and structural relationships for the Neoproterozoic Mount Rogers and Konnarock formations, the northeast end of the Mountain City window, the separation of Mesoproterozoic rocks of the Blue Ridge into three age groups, and timing and emplacement of the Blue Ridge thrust sheet. The study area includes folded and faulted Paleozoic strata of the Valley and Ridge to metamorphic and igneous rocks of the Blue Ridge. In the Valley and Ridge, Cambrian to Middle Ordovician carbonate and clastic rocks are exposed in a syncline on the Pulaski thrust sheet; these rocks are overridden by the Blue Ridge thrust sheet. The northeast end of the Mountain City window is interpreted as a simple window; the Stone Mountain fault is folded and continues as the Iron Mountain fault on the NW-side of the window. The Stone Mountain fault does not exist to the NE near the Razor Ridge volcanic center. Instead a continuous section of Proterozoic gneisses, Mount Rogers Formation, Konnarock Formation and Chilhowee Group is now recognized. Rhyolites of the Mount Rogers Formation range from 760–749Ma, with detrital zircon age populations from associated volcaniclastic rocks indicating magmatism and rifting began by ~780 Ma. Rhyolite blocks in the Konnarock Formation and a change from rift-related clastic rocks of the Mount Rogers Formation transitioning to maroon laminites and laminites with dropstones, suggest that the Konnarock Formation may be as old as ~749 Ma. Mesoproterozoic crystalline rocks of the Blue Ridge, previously referred to as the Cranberry Gneiss, are separated based on field relationships and SHRIMP U–Pb geochronology: (1) pre-Grenvillian crust,1.33 Ga; (2) 1190–1140 Ma granitoids; and (3) 1075–1030 Ma granitoids. Multiple greenschist-facies high-strain zones, including the 2–11 km wide Fries high-strain zone, occur in the Blue Ridge thrust sheet. Fabrics across the Fries and Gossan Lead faults have similar orientations and NW–directed contractional deformation. 40Ar/39Ar hornblende, muscovite, and K-feldspar ages indicate the western and eastern Blue Ridge had different thermal histories. The eastern Blue Ridge (Gossan Lead thrust sheet) experienced a 360–340 Ma amphibolite facies event prior to juxtaposition with the western Blue Ridge. 40Ar/39Ar muscovite ages in western Blue Ridge rocks document greenschist facies metamorphism and deformation and emplacement of the Blue Ridge thrust sheet at ~340 Ma; the Catface and Fries faults are tentatively interpreted to be contemporaneous. After initial emplacement of the Blue Ridge thrust sheet at ~340 Ma, shortening was accommodated by westward translation along the basal decollement, which carried the Blue Ridge thrust sheet to its final position.

Crustal structure and tectonics of the Hidaka Collision Zone, Hokkaido (Japan), revealed by vibroseis seismic reflection and gravity surveys

NASA Astrophysics Data System (ADS)

Arita, Kazunori; Ikawa, Takashi; Ito, Tanio; Yamamoto, Akihiko; Saito, Matsuhiko; Nishida, Yasunori; Satoh, Hideyuki; Kimura, Gaku; Watanabe, Teruo; Ikawa, Takeshi; Kuroda, Toru

1998-05-01

This study is the first integrated geological and geophysical investigation of the Hidaka Collision Zone in southern Central Hokkaido, Japan, which shows complex collision tectonics with a westward vergence. The Hidaka Collision Zone consists of the Idon'nappu Belt (IB), the Poroshiri Ophiolite Belt (POB) and the Hidaka Metamorphic Belt (HMB) with the Hidaka Belt from west to east. The POB (metamorphosed ophiolites) is overthrust by the HMB (steeply eastward-dipping palaeo-arc crust) along the Hidaka Main Thrust (HMT), and in turn, thrusts over the Idon'nappu Belt (melanges) along the Hidaka Western Thrust (HWT). Seismic reflection and gravity surveys along a 20-km-long traverse across the southern Hidaka Mountains revealed hitherto unknown crustal structures of the collision zone such as listric thrusts, back thrusts, frontal thrust-and-fold structures, and duplex structures. The main findings are as follows. (1) The HMT, which dips steeply at the surface, is a listric fault dipping gently at a depth of ˜7 km beneath the eastern end of the HMB, and cutting across the lithological boundaries and schistosity of the Hidaka metamorphic rocks. (2) A second reflector is detected 1 km below the HMT reflector. The intervening part between these two reflectors is inferred to be the POB, which is only little exposed at the surface. This inference is supported by the high positive Bouguer anomalies along the Hidaka Mountains. (3) The shallow portion of the IB at the front of the collision zone has a number of NNE-dipping reflectors, indicative of imbricated fold-and-thrust structures. (4) Subhorizontal reflectors at a depth of 14 km are recognized intermittently at both sides of the seismic profile. These reflectors may correspond to the velocity boundary (5.9-6.6 km/s) previously obtained from seismic refraction profiling in the northern Hidaka Mountains. (5) These crustal structures as well as the back thrust found in the eastern end of the traverse represent characteristics of collisional tectonics resulting from the two collisional events since the Early Tertiary.

The thrust belt in Southwest Montana and east-central Idaho

USGS Publications Warehouse

Ruppel, Edward T.; Lopez, David A.

1984-01-01

The leading edge of the Cordilleran fold and thrust in southwest Montana appears to be a continuation of the edge of the Wyoming thrust belt, projected northward beneath the Snake River Plain. Trces of the thrust faults that form the leading edge of the thrust belts are mostly concealed, but stratigraphic and structural evidence suggests that the belt enters Montana near the middle of the Centennial Mountains, continues west along the Red Rock River valley, and swings north into the Highland Mountains near Butte. The thrust belt in southwest Montana and east-central Idaho includes at least two major plates -- the Medicine Lodge and Grasshopper thrust plates -- each of which contains a distinctive sequence of rocks, different in facies and structural style from those of the cratonic region east of the thrust belt. The thrust plates are characterized by persuasive, open to tight and locally overturned folds, and imbricate thrust faults, structural styles unusual in Phanerozoic cratonic rocks. The basal decollement zones of the plates are composed of intensely sheared, crushed, brecciated, and mylonitized rocks, the decollement at the base of the Medicine Lodge plate is as much as 300 meters thick. The Medicine Lodge and Grasshopper thrust plates are fringed on the east by a 10- to 50-kilometer-wide zone of tightly folded rocks cut by imbricate thrust fauls, a zone that forms the eastern margin of the thrust belt in southwest Montana. The frontal fold and thrust zone includes rocks that are similar to those of the craton, even though they differ in details of thickness, composition, or stratigraphic sequence. The zone is interpreted to be one of terminal folding and thrusting in cratonic rocks overridden by the major thrust plates from farther west. The cratonic rocks were drape-folded over rising basement blocks that formed a foreland bulge in front of the thrust belt. The basement blocks are bounded by steep faults of Proterozoic ancestry, which also moved as tear faults during thrusting, and seem to have controlled the curving patterns of salients and reentrants at the leading edge of the thrust belt. Radiometric and stratiographic evidence shows that the thrust belt was in its present position by about 75 million year go.

Reprocessing and Interpretation of Vintage Seismic Reflection Data: Evidence for the Tectonic History of the Rocky Mountain Trench, Northwest Montana.

NASA Astrophysics Data System (ADS)

Porter, M.; Speece, M. A.; Rutherford, B. S.; Constenius, K. N.

2014-12-01

In 1983 Techno, Inc. collected five seismic reflection profiles in the region between Whitefish, Montana and the United States-Canada border. The poulter method was used to gather four of these profiles and one profile was collected using a vibroseis source. We are currently reprocessing these data in order to construct a regional geological interpretation. The profiles cover a key position in the hinterland of the Cordillera in the lee of the Lewis thrust salient where the east-northeast verging Lewis thrust fault system translated (horizontal displacement >100 km) and inverted a thick, strong slab of primarily Belt-Purcell rocks out of a deep Precambrian depositional basin onto a cratonic platform. In this event, Belt-Purcell rocks were thrust over complexly imbricated Phanerozoic strata in the foreland. Late Mesozoic compressional deformation was followed by Cenozoic extensional collapse of the over-thickened Cordillera and subsequent basin and range style deformation that produced an array of northwest trending grabens. Three of the seismic profiles cross the Rocky Mountain Trench; the Trench is a linear structure of regional dimension that is an expression of the extensional fragmentation of the Cordillera. Strong reflections, interpreted as sills encased within Lower Belt rocks (encountered in the Arco-Marathon 1 Paul Gibbs borehole), outline the complexly folded and faulted structure of the eastern limb of the Purcell anticlinorium. East of the Rocky Mountain Trench stratified reflections within Belt rocks clearly outline the Wigwam Thrust. Beneath the Whitefish Range, an apparent inflection in the strongly reflective basal Cambrian veneer marks the westerly increase in dip of the Rocky Mountain Basal Detachment. The dip contrast between the foreland and hinterland might be a manifestation of the tectonic loading of the Belt basin margin and the loading might have localized extension across the Rocky Mountain Trench.

The sup 40 Ar/ sup 39 Ar geochronology of the Pelona schist and related rocks, southern California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jacobson, C.E.

1990-01-10

Seventeen {sup 40}Ar/{sup 39}Ar ages for hornblende, celadonitic muscovite, and biotite from the Pelona, Orocopia, Rand, and Portal Ridge (POR) schists range from 39 to 85 Ma. Two muscovites and one hornblende from the Rand Schist have ages of 72 to 74 Ma, indistinguishable from the K-Ar age of 74 Ma for hornblende from a posttectonic granodiorite that intrudes the schist, but younger than the 70 Ma U-Pb age of the intrusion. Four muscovite and two hornblende ages for schist and mylonite from the East Fork area of the San Gabriel Mountains range from 55 to 61 Ma. Concordance ofmore » schist and upper plate ages confirms structural and metamorphic evidence that the Vincent thrust in the San Gabriel Mountains has not undergone significant postmetamorphic disruption. Ages from the Orocopia Mountains are 75 Ma for hornblende from nonmylonitic upper plate, 52 Ma for muscovite from structurally high Orocopia Schist that is mylonitic, and 41 Ma for muscovite from nonmylonitic Orocopia Schist. These are consistent with field evidence that the Orocopia thrust is a postmetamorphic normal fault. Muscovite and hornblende from the Gavilan Hills have ages of 48 to 50 Ma, younger than ages from the San Gabriel Mountains but similar to schist ages from the Orocopia Mountains. The geochronologic and structural complexities of the Vincent, Chocolate Mountains, Orocopia, and Rand thrusts imply that previously cited northeastward vergence may not relate to prograde metamorphism (subduction) of the POR schists. The data indicate substantial uplift of the POR schists prior to middle Tertiary detachment faulting, which confirms other geochronologic evidence of uplift in southern California and southern Arizona during the Late Cretaceous-early Tertiary.« less

Co-seismic ruptures of the 12 May 2008, Ms 8.0 Wenchuan earthquake, Sichuan: East-west crustal shortening on oblique, parallel thrusts along the eastern edge of Tibet

USGS Publications Warehouse

Liu-Zeng, J.; Zhang, Z.; Wen, L.; Tapponnier, P.; Sun, Jielun; Xing, X.; Hu, G.; Xu, Q.; Zeng, L.; Ding, L.; Ji, C.; Hudnut, K.W.; van der Woerd, J.

2009-01-01

The Ms 8.0, Wenchuan earthquake, which devastated the mountainous western rim of the Sichuan basin in central China, produced a surface rupture over 200??km-long with oblique thrust/dextral slip and maximum scarp heights of ~ 10??m. It thus ranks as one of the world's largest continental mega-thrust events in the last 150??yrs. Field investigation shows clear surface breaks along two of the main branches of the NE-trending Longmen Shan thrust fault system. The principal rupture, on the NW-dipping Beichuan fault, displays nearly equal amounts of thrust and right-lateral slip. Basin-ward of this rupture, another continuous surface break is observed for over 70??km on the parallel, more shallowly NW-dipping Pengguan fault. Slip on this latter fault was pure thrusting, with a maximum scarp height of ~ 3.5??m. This is one of the very few reported instances of crustal-scale co-seismic slip partitioning on parallel thrusts. This out-of-sequence event, with distributed surface breaks on crustal mega-thrusts, highlights regional, ~ EW-directed, present day crustal shortening oblique to the Longmen Shan margin of Tibet. The long rupture and large offsets with strong horizontal shortening that characterize the Wenchuan earthquake herald a re-evaluation of tectonic models anticipating little or no active shortening of the upper crust along this edge of the plateau, and require a re-assessment of seismic hazard along potentially under-rated active faults across the densely populated western Sichuan basin and mountains. ?? 2009 Elsevier B.V.

The Lewis thrust fault and related structures in the Disturbed Belt, northwestern Montana

USGS Publications Warehouse

Mudge, Melville Rhodes; Earhart, Robert L.

1980-01-01

The classical Lewis thrust fault in Glacier National Park has now been mapped 125 km south of the park to Steamboat Mountain, where the trace dies out in folded middle Paleozoic rocks. The known length of the fault is 452 km, extending northward from Steamboat Mountain to a point 225 km into Canada, where the fault also dies out in Paleozoic rocks. At the south end, the surface expression of the Lewis thrust begins in a shear zone in folded Mississippian rocks. To the north, the thrust progressively cuts downsection into Proterozoic Y (Belt) rocks near Glacier National Park. Displacement on the Lewis plate increases northward from approximately 3 km on an easterly trending hinge line at the West Fork of the Sun River to a postulated 65 km at the southern edge of the park, where the stratigraphic throw is about 6,500 m. Present data indicate the thrust formed during very late Paleocene to very early Eocene time. The Lewis thrust and related structures, the Hoadley thrust and the Continental Divide syncline, probably formed concurrently under the same stress field. The northern limit of the trace of the Hoadley thrust is within the lower portion of the Lewis plate, about 28 km north of where the Lewis thrust develops, and the Hoadley extends for at least 125 km to the south. Displacement of the Hoadley increases southward from about 1 km at the hinge line to an inferred 70 km near its known southern extent. If our inference is correct, the Hoadley is nearly the southern mirror image of the Lewis to the north. The Continental Divide syncline, a doubly plunging, broad, northerly trending open fold that is about 120 km long, is a major fold within the Lewis plate.

Correlation, sedimentology, structural setting, chemical composition, and provenance of selected formations in Mesoproterozoic Lemhi Group, central Idaho

USGS Publications Warehouse

Tysdal, Russell G.; Lindsey, David A.; Taggart, Joseph E.

2003-01-01

A unit of the Mesoproterozoic Apple Creek Formation of the Lemhi Range previously was correlated with part of the lower subunit of the Mesoproterozoic Yellowjacket Formation in the Salmon River Mountains. Strata currently assigned to the middle subunit of the Yellowjacket Formation lie conformably above the Apple Creek unit in the Salmon River Mountains, and are here renamed the banded siltite unit and reassigned to the Apple Creek Formation. Almost all of the banded siltite unit is preserved within the Salmon River Mountains, where it grades upward into clastic rocks that currently are assigned to the upper subunit of the Yellowjacket Formation and that here are reassigned to the Gunsight Formation. The banded siltite unit of the Apple Creek Formation is composed of a turbidite sequence, as recognized by previous workers. Uppermost strata of the unit were reworked by currents, possibly storm generated, and adjusted to a high water content by developing abundant soft-sediment deformation features. Basal strata of the overlying Gunsight Formation in the Salmon River Mountains display abundant hummocky crossbeds, storm-generated features deposited below fair-weather wave base, that are conformable above the storm-reworked deposits. The hummocky crossbedded strata grade upward into marine shoreface strata deposited above fair-weather wave base, which in turn are succeeded by fluvial strata. Hummocky and shoreface strata are absent from the Gunsight Formation in the Lemhi Range. The major thickness of the Gunsight Formation in both the Salmon River Mountains and the Lemhi Range is composed of fluvial rocks, transitional in the upper part into marine rocks of the Swauger Formation. The fluvial strata are mainly characterized by stacked sheets of metasandstone and coarse siltite; they are interpreted as deposits of braided rivers. The Poison Creek thrust fault of the Lemhi Range extends northwestward through the study area in the east-central part of the Salmon River Mountains. The Apple Creek and Gunsight Formations on the southwest side of the thrust fault were transported to the northeast as part of the Poison Creek thrust sheet. A segment of the thrust fault within the Gunsight Formation in the Salmon River Mountains subsequently underwent normal displacement. Along this segment, lower Gunsight strata on the southwest were juxtaposed against upper Gunsight and Swauger strata on the northeast.

Geologic map of the Lazy Y Point Quadrangle, Moffat County Colorado

USGS Publications Warehouse

Van Loenen, R. E.; Selner, G.I.; Bryant, W.A.

1999-01-01

The Lazy Y Point quadrangle is in northwestern Colorado a few miles north of Rangely. The prominent structural feature of the Lazy Y Point quadrangle is the Skull Creek monocline. Pennsylvanian rocks are exposed along the axis of the monocline while hogbacks along its southern flank expose rocks that are from Permian to Upper Cretaceous in age. The Wolf Creek monocline and the Wolf Creek thrust fault, which dissects the monocline, are salient structural features in the northern part of the quadrangle. Little or no mineral potential exists within the quadrangle. A geologic map of the Skull Creek quadrangle, which is adjacent to the Lazy Y Point quadrangle on the east, is also available (Geologic Investigations Series I-2647). This companian map shows similar geologic features, including the eastern half of the Skull Creek monocline. The geology of this quadrangle was mapped because of its proximity to Dinosaur National Monument. It is adjacent to quadrangles previously mapped to display the geology of this very scenic and popular National Monument. The Lazy Y Point quadrangle includes parts of the Willow and Skull Creek Wilderness Study Areas, which were assessed for their mineral resource potential.

Thrust-ridge paleodepositional model for the Upper Freeport coal bed and associated clastic facies, Upper Potomac coal field, Appalachian Basin, U.S.A.

USGS Publications Warehouse

Belt, Edward S.; Lyons, P.C.

1990-01-01

Two differential depositional sequences are recognized within a 37-m-thick lowermost section of the Conemaugh Group of Late Pennsylvanian (Westphalian D) age in the southern part of the Upper Potomac coal field (panhandle of Maryland and adjacent West Virginia). The first sequence is dominated by the Upper Freeport coal bed and zone (UF); the UF consists of a complex of interfingered thick coal beds and mudrocks. The UF underlies the entire 500 km2 study area (approximately 40 km in a NE-SW direction). The second sequence is dominated by medium- to coarse-grained sandstone and pebbly sandstone. They were deposited in channel belts that cut into and interfingered laterally with mudrock and fine- to medium-grained sandstone facies of floodbasin and crevasse-lobe origin. Thin lenticular coals occur in the second sequence. Nowhere in the study area does coarse-grained sandstone similar to the sandstone of the channel belts of the second sequence occur within the UF. However, 20 km north of the study area, coarse channel belts are found that are apparently synchronous with the UF (Lyons et al., 1984). The southeastern margin of the study are is bounded by the Allegheny Front. Between it and the North Mountain thrust (75 km to the southeast), lie at least eight other thrusts of unknown extent (Wilson, 1887). All these thrusts are oriented northwest; Devonian and older strata are exposed at the surface between the Allegheny Front and the North Mountain thrust. A blind-thrust ridge model is proposed to explain the relation of the two markedly depositional sequences to the thrusts that lie to the southeast of the Upper Potomac coal field. This model indicates that thrust ridges diverted coarse clastics from entering the swamp during a period when the thick Upper Freeport peat accumulated. Anticlinal thrust ridges and associated depressions are envisioned to have developed parallel to the Appalachian orogen during Middle and early Late Pennsylvanian time. A blind thrust developed from one of the outboard ridges, and it was thrust farther outboard ahead of the main body of the orogen. Sediment derived from the orogen was diverted into a sediment trap inboard of the ridge (Fig. 1). The ridge prevented sediment from entering the main peat-forming swamp. Sediment shed from the orogen accumulated in the sediment trap was carried out of the ends of the trap by steams that occupied the shear zone at the ends of the blind-thrust ridge (Fig. 1). Remnants of blind-thrust ridges occurs in the Sequatchie Valley thrust and the Pine Mountain thrust of the southern Appalachians. The extent, parallel to the orogen, of the thick areally extensive UF coal is related to the length of the blind-thrust ridge that, in turn, controlled the spacing of the river-derived coarse clastics that entered the main basin from the east. Further tectonism caused the thrust plane to emerge to the surface of the blind-thrust ridge. Peat accumulation was then terminated by the rapid erosion of the blind-thrust ridge and by the release of trapped sediment behind it. The peat was buried by sediments from streams from closely spaced channel belts] with intervening floodbasins. The model was implications for widespread peat (coal) deposits that developed in tropical regions, a few hundred kilometers inland from the sea during Pennsylvanian time (Belt and Lyons, 1989). ?? 1990.

Biostratigraphy and structure of paleozoic host rocks and their relationship to Carlin-type gold deposits in the Jerritt Canyon mining district, Nevada

USGS Publications Warehouse

Peters, S.G.; Armstrong, A.K.; Harris, A.G.; Oscarson, R.L.; Noble, P.J.

2003-01-01

The Jerritt Canyon mining district in the northern Independence Range, northern Nevada, contains multiple, nearly horizontal, thrust masses of platform carbonate rocks that are exposed in a series of north- to northeast-elongated, tectonic windows through rocks of the Roberts Mountains allochthon. The Roberts Mountains allochthon was emplaced during the Late Devonian to Early Mississippian Antler orogeny. These thrust masses contain structurally and stratigraphically controlled Carlin-type gold deposits. The gold deposits are hosted in tectonically truncated units of the Silurian to Devonian Hanson Creek and Roberts Mountains Formations that lie within structural slices of an Eastern assemblage of Cambrian to Devonian carbonate rocks. In addition, these multiply thrust-faulted and folded host rocks are structurally interleaved with Mississippian siliciclastic rocks and are overlain structurally by Cambrian to Devonian siliciclastic units of the Roberts Mountains allochthon. All sedimentary rocks were involved in thrusting, high-angle faulting, and folding, and some of these events indicate substantial late Paleozoic and/or Mesozoic regional shortening. Early Pennsylvanian and late Eocene dikes also intrude the sedimentary rocks. These rocks all were uplifted into a northeast-trending range by subsequent late Cenozoic Basin and Range faulting. Eocene sedimentary and volcanic rocks flank part of the range. Pathways of hydrothermal fluid flow and locations of Carlin-type gold orebodies in the Jerritt Canyon mining district were controlled by structural and host-rock geometries within specific lithologies of the stacked thrust masses of Eastern assemblage rocks. The gold deposits are most common proximal to intersections of northeast-striking faults, northwest-striking dikes, and thrust planes that lie adjacent to permeable stratigraphic horizons. The host stratigraphic units include carbonate sequences that contained primary intercrystalline permeability, which provided initial pathways for fluid flow and later served as precipitation sites for ore minerals. Alteration, during, and perhaps prior to mineralization, enhanced primary permeability by dissolution, by removal of calcite, and by formation of dolomite. Ore-stage sulfide minerals and alteration minerals commonly precipitated in pore spaces among dolomite grains. Microveinlets and microbrecciation in zones of intense alteration also provided networks of secondary permeability that further enhanced fluid flux and produced additional sites for ore deposition.

Laramide structure of the central Sangre de Cristo Mountains and adjacent Raton Basin, southern Colorado

USGS Publications Warehouse

Lindsey, D.A.

1998-01-01

Laramide structure of the central Sangre de Cristo Mountains (Culebra Range) is interpreted as a system of west-dipping, basement-involved thrusts and reverse faults. The Culebra thrust is the dominant structure in the central part of the range; it dips 30 -55?? west and brings Precambrian metamorphic base-ment rocks over unmetamorphosed Paleozoic rocks. East of the Culebra thrust, thrusts and reverse faults break the basement and overlying cover rocks into north-trending fault blocks; these boundary faults probably dip 40-60?? westward. The orientation of fault slickensides indicates oblique (northeast) slip on the Culebra thrust and dip-slip (ranging from eastward to northward) movement on adjacent faults. In sedimentary cover rocks, east-vergent anticlines overlie and merge with thrusts and reverse faults; these anticlines are interpreted as fault-propagation folds. Minor east-dipping thrusts and reverse faults (backthrusts) occur in both the hanging walls and footwalls of thrusts. The easternmost faults and folds of the Culebra Range form a continuous structural boundary between the Laramide Sangre de Cristo highland and the Raton Basin. Boundary structures consist of west-dipping frontal thrusts flanked on the basinward side by poorly exposed, east-dipping backthrusts. The backthrusts are interpreted to overlie structural wedges that have been emplaced above blind thrusts in the basin margin. West-dipping frontal thrusts and blind thrusts are interpreted to involve basement, but backthrusts are rooted in basin-margin cover rocks. At shallow structural levels where erosion has not exposed a frontal thrust, the structural boundary of the basin is represented by an anticline or monocline. Based on both regional and local stratigraphic evidence, Laramide deformation in the Culebra Range and accompanying synorogenic sedimentation in the western Raton Basin probably took place from latest Cretaceous through early Eocene time. The earliest evidence of uplift and erosion of a highland is the appearance of abundant feldspar in the Late Cretaceous Vermejo Formation. Above the Vermejo, unconformities overlain by conglomerate indicate continued thrusting and erosion of highlands from late Cretaceous (Raton) through Eocene (Cuchara) time. Eocene alluvial-fan conglomerates in the Cuchara Formation may represent erosion of the Culebra thrust block. Deposition in the Raton Basin probably shifted north from New Mexico to southern Colorado from Paleocene to Eocene time as movement on individual thrusts depressed adjacent segments of the basin.

Quasi-Steady Evolution of Hillslopes in Layered Landscapes: An Analytic Approach

NASA Astrophysics Data System (ADS)

Glade, R. C.; Anderson, R. S.

2018-01-01

Landscapes developed in layered sedimentary or igneous rocks are common on Earth, as well as on other planets. Features such as hogbacks, exposed dikes, escarpments, and mesas exhibit resistant rock layers adjoining more erodible rock in tilted, vertical, or horizontal orientations. Hillslopes developed in the erodible rock are typically characterized by steep, linear-to-concave slopes or "ramps" mantled with material derived from the resistant layers, often in the form of large blocks. Previous work on hogbacks has shown that feedbacks between weathering and transport of the blocks and underlying soft rock can create relief over time and lead to the development of concave-up slope profiles in the absence of rilling processes. Here we employ an analytic approach, informed by numerical modeling and field data, to describe the quasi-steady state behavior of such rocky hillslopes for the full spectrum of resistant layer dip angles. We begin with a simple geometric analysis that relates structural dip to erosion rates. We then explore the mechanisms by which our numerical model of hogback evolution self-organizes to meet these geometric expectations, including adjustment of soil depth, erosion rates, and block velocities along the ramp. Analytical solutions relate easily measurable field quantities such as ramp length, slope, block size, and resistant layer dip angle to local incision rate, block velocity, and block weathering rate. These equations provide a framework for exploring the evolution of layered landscapes and pinpoint the processes for which we require a more thorough understanding to predict their evolution over time.

JPRS Report, Soviet Union, Aviation and Cosmonautics, No. 7, July 1987.

DTIC Science & Technology

1988-01-14

CONTENTS u JANUARY ms Improvement in Elements of Combat Potential Traced [I. Sviridov] 1 More Realistic Pilot Training Under Mountain Conditions Urged...training commenced. The arriv- ing Soviet aviators became familiar with a new flight area for them and improved their skills in mountain flights...withstand the thrust of the units of the Edelweiss Division which had been specially trained for fighting in mountain areas. But they firmly

Late Oligocene to present contractional structure in and around the Susitna basin, Alaska—Geophysical evidence and geological implications

USGS Publications Warehouse

Saltus, Richard W.; Stanley, Richard G.; Haeussler, Peter J.; Jones, James V.; Potter, Christopher J.; Lewis, Kristen A.

2016-01-01

The Cenozoic Susitna basin lies within an enigmatic lowland surrounded by the Central Alaska Range, Western Alaska Range (including the Tordrillo Mountains), and Talkeetna Mountains in south-central Alaska. Some previous interpretations show normal faults as the defining structures of the basin (e.g., Kirschner, 1994). However, analysis of new and existing geophysical data shows predominantly (Late Oligocene to present) thrust and reverse fault geometries in the region, as previously proposed by Hackett (1978). A key example is the Beluga Mountain fault where a 50-mGal gravity gradient, caused by the density transition from the igneous bedrock of Beluga Mountain to the >4-km-thick Cenozoic sedimentary section of Susitna basin, spans a horizontal distance of ∼40 km and straddles the topographic front. The location and shape of the gravity gradient preclude a normal fault geometry; instead, it is best explained by a southwest-dipping thrust fault, with its leading edge located several kilometers to the northeast of the mountain front, concealed beneath the shallow glacial and fluvial cover deposits. Similar contractional fault relationships are observed for other basin-bounding and regional faults as well. Contractional structures are consistent with a regional shortening strain field inferred from differential offsets on the Denali and Castle Mountain right-lateral strike-slip fault systems.

Geologic Map of the Eastern Three-Quarters of the Cuyama 30' x 60' Quadrangle, California

USGS Publications Warehouse

Kellogg, Karl S.; Minor, Scott A.; Cossette, Pamela M.

2008-01-01

The map area encompasses a large part of the western Transverse Ranges and southern Coast Ranges of southern California. The San Andreas fault (SAF) cuts the northern part of the map. The area south of the SAF, about 80 percent of the map area, encompasses several distinct tectonic blocks bounded by major thrust or reverse faults, including the Santa Ynez fault, Big Pine fault (and structurally continuous Pine Mountain fault), Tule Creek fault, Nacimiento fault, Ozena fault, Munson Creek fault, Morales fault, and Frazier Mountain Thrust System. Movement on these faults is as old as Miocene and some faults may still be active. In addition, the Paleocene Sawmill Mountain Thrust south of the SAF and the Pastoria Thrust north of the SAF place Cretaceous and older crystalline rocks above Pelona Schist (south of the SAF) and Rand Schist (north of the SAF). South of the SAF, each tectonic block contains a unique stratigraphy, reflecting either large-scale movement on bounding faults or different depositional environments within each block. On Mount Pinos and Frazier Mountain, intrusive and metamorphic rocks as old as Mesoproterozoic, but including voluminous Cretaceous granitoid rocks, underlie or are thrust above non-marine sedimentary rocks as old as Miocene. Elsewhere, marine and non-marine sedimentary rocks are as old as Cretaceous, dominated by thick sequences of both Eocene and Cretaceous marine shales and sandstones. Middle Miocene to early Oligocene volcanic rocks crop out in the Caliente Hills (part of Caliente Formation) and south of Mount Pinos (part of the Plush Ranch Formation). Fault-bounded windows of Jurassic Franciscan Complex ophiolitic rocks are evident in the southwest corner of the area. North of the SAF, marine and non-marine sedimentary rocks as old as Eocene and Miocene volcanic rocks overlie a crystalline basement complex. Basement rocks include Cretaceous intrusive rocks that range from monzogranite to diorite, and Jurassic to late Paleozoic intrusive and metamorphic rocks. The Jurassic to late Paleozoic intrusive rocks include diorite, gabbro, and ultramafic rocks, and the metasedimentary rocks include marble, quartzite, schist, and gneiss.

Flower-strucutre deformation pattern of theTian Shan mountains as revealed by Late Quaternary geological and modern Geodesy slip rates

NASA Astrophysics Data System (ADS)

Wu, C.; Zhang, P.; Zheng, W.; Wang, H.; Zhang, Z.; Ren, Z.; Zheng, D.; Yu, J.; Wu, G.

2017-12-01

The deformation pattern and strain distribution of the Tian Shan is a hot issue.Previous studies mainly focus on the thrust-fold systems on both sides of Tian Shan, the strike-slip faults within the mountains are rarely reported. The understanding about the deformation characteristics of Tian Shan is not complete for lacking information of these strike-slip faults.Our studies show the NEE trending structures of Maidan fault and Nalati fault in the southwestern Tian Shan are all active during the Holence. These faults are characterized by sinistral strike-slip and thrust movement. The minimum average sinistral strike-slip rate of the Maidan fault is 1.07 ± 0.13 mm/yr. During the late Quaternary, the average shortening rate and sinistral strike-slip rate of the Nalati fault are 2.1 ±0.4 mm/yr and 2.56 ±0.25 mm/yr, respectively . In the interior of the Tian Shan area, two groups of strike-slip faults were developed. The NEE trending faults with sinistral strike-slipmovement, and the NWW trending faults with dextral strike-slip movement show the shape of "X"in geometrical structure. The piedmont thrust faults and the thrust strike-slip faults in the interior mountain constitute the tectonic framework of Tian Shan. Threegroups of active fault systems are the main seismogenic and geological structures, which control the current tectonic deformation pattern of Tian Shan (Figure 1). GPS observation data also showthe similar deformation characteristics with the geological results (Figures 2, 3). In addition to the crustal shortening, there is a certain strike-slip shear movement in the interior of the Tian Shan.The strike-slip rate defined by the geological and GPS data is approximately consistent with each other near the same longitude. We suggest the two groups of strike-slip faults in the interior of mountains is a set of conjugate structures. The whole Tian Shan forms a large flower-structure in a profile view. The complete tectonic deformation of the Tian Shan mountains consists ofthe shortening deformationof the N-S direction and the lateral extrusion of the E-W direction (Figure 2). The late Cenozoic deformation of the Tian Shan mountains is due to the northward subduction of Tarim Block. Although the activedeformation of the Tian Shan decrease eastward, the geological sturcutrein eastern Tian Shan is similar.

Fold-to-fault progression of a major thrust zone revealed in horses of the North Mountain fault zone, Virginia and West Virginia, USA

USGS Publications Warehouse

Orndorff, Randall C.

2012-01-01

The method of emplacement and sequential deformation of major thrust zones may be deciphered by detailed geologic mapping of these important structures. Thrust fault zones may have added complexity when horse blocks are contained within them. However, these horses can be an important indicator of the fault development holding information on fault-propagation folding or fold-to-fault progression. The North Mountain fault zone of the Central Appalachians, USA, was studied in order to better understand the relationships of horse blocks to hanging wall and footwall structures. The North Mountain fault zone in northwestern Virginia and eastern panhandle of West Virginia is the Late Mississippian to Permian Alleghanian structure that developed after regional-scale folding. Evidence for this deformation sequence is a consistent progression of right-side up to overturned strata in horses within the fault zone. Rocks on the southeast side (hinterland) of the zone are almost exclusively right-side up, whereas rocks on the northwest side (foreland) of the zone are almost exclusively overturned. This suggests that the fault zone developed along the overturned southeast limb of a syncline to the northwest and the adjacent upright limb of a faulted anticline to the southeast.

Interseismic Strain Accumulation Across Metropolitan Los Angeles: Puente Hills Thrust

NASA Astrophysics Data System (ADS)

Argus, D.; Liu, Z.; Heflin, M. B.; Moore, A. W.; Owen, S. E.; Lundgren, P.; Drake, V. G.; Rodriguez, I. I.

2012-12-01

Twelve years of observation of the Southern California Integrated GPS Network (SCIGN) are tightly constraining the distribution of shortening across metropolitan Los Angeles, providing information on strain accumulation across blind thrust faults. Synthetic Aperture Radar Interferometry (InSAR) and water well records are allowing the effects of water and oil management to be distinguished. The Mojave segment of the San Andreas fault is at a 25° angle to Pacific-North America plate motion. GPS shows that NNE-SSW shortening due to this big restraining bend is fastest not immediately south of the San Andreas fault across the San Gabriel mountains, but rather 50 km south of the fault in northern metropolitan Los Angeles. The GPS results we quote next are for a NNE profile through downtown Los Angeles. Just 2 mm/yr of shortening is being taken up across the San Gabriel mountains, 40 km wide (0.05 micro strain/yr); 4 mm/yr of shortening is being taken up between the Sierra Madre fault, at the southern front of the San Gabriel mountains, and South Central Los Angeles, also 40 km wide (0.10 micro strain/yr). We find shortening to be more evenly distributed across metropolitan Los Angeles than we found before [Argus et al. 2005], though within the 95% confidence limits. An elastic models of interseismic strain accumulation is fit to the GPS observations using the Back Slip model of Savage [1983]. Rheology differences between crystalline basement and sedimentary basin rocks are incorporated using the EDGRN/EDCMP algorithm of Wang et al. [2003]. We attempt to place the Back Slip model into the context of the Elastic Subducting Plate Model of Kanda and Simons [2010]. We find, along the NNE profile through downtown, that: (1) The deep Sierra Madre Thrust cannot be slipping faster than 2 mm/yr, and (2) The Puente Hills Thrust and nearby thrust faults (such as the upper Elysian Park Thrust) are slipping at 9 ±2 mm/yr beneath a locking depth of 12 ±5 km (95% confidence limits). Incorporating sedimentary basin rock either reduces the slip rate by 10 per cent or increases the locking rate by 20 per cent. The 9 mm/yr rate for the Puente Hills Thrust and nearby faults exceeds the cumulative 3-5 mm/yr rate estimated using paleoseismology along the Puente Hills Thrust (1.2-1.6 mm/yr, Dolan et al. 2003), upper Elysian Park Thrust (0.6-2.2 mm/yr, Oskin et al. 2000), and western Compton Thrust (1.2 mm/yr, Leon et al. 2009], though all the paleoseismic estimates are minimums. We infer that M 7 earthquakes in northern metropolitan Los Angeles may occur more frequently that previously thought.

Geochemistry and field geology of shoshonitic magmas in the Late Cretaceous foreland fold and thrust belt of southwestern Montana: Results from the North Doherty Mountain Intrusive Complex

NASA Astrophysics Data System (ADS)

Beranek, L. P.; Burton, B. R.; Ihinger, P. D.

2002-12-01

The North Doherty Mountain Intrusive Complex (NDMIC) is one of several satellite plutons related to the areally extensive Boulder batholith of southwestern Montana. The Boulder batholith comprises multiple plutons and intrusive phases, and the magmatism has long been thought to be the result of subduction due to its calc-alkaline granodioritic composition. The batholith is situated in the Helena salient, which differs from other parts of the North American Cordilleran foreland because there, magmatism spatially and temporally overlaps with deformation in the foreland fold and thrust belt. The North Doherty Mountain Intrusive Complex (NDMIC) is one of several satellite plutons related to the Boulder batholith and represents an ideal microcosm of the batholith for petrogenetic and structural studies because it exposes both mafic and felsic units and was emplaced in the limb of a major thrust related fold. We present new geologic mapping and detailed trace element geochemical analyses to show that the entire mafic-to-felsic suite of rocks in the NDMIC are cogenetic and shoshonitic in character. Shoshonites are unusual magmas that are distinguished by their high concentrations of K, Rb, Sr, Ba, Zr, and Th contents, and are thought to represent partial melting at great depths within the mantle wedge above a subducting slab. The presence of shoshonitic magma in the Cordilleran foreland fold and thrust belt provides important clues into the nature of the formation of this unusual magma type and can provide insights into our understanding of magmatism in foreland structural settings.

First-order control of syntectonic sedimentation on crustal-scale structure of mountain belts

NASA Astrophysics Data System (ADS)

Erdős, Zoltán.; Huismans, Ritske S.; van der Beek, Peter

2015-07-01

The first-order characteristics of collisional mountain belts and the potential feedback with surface processes are predicted by critical taper theory. While the feedback between erosion and mountain belt structure has been fairly extensively studied, less attention has been given to the potential role of synorogenic deposition. For thin-skinned fold-and-thrust belts, recent studies indicate a strong control of syntectonic deposition on structure, as sedimentation tends to stabilize the thin-skinned wedge. However, the factors controlling basement deformation below fold-and-thrust belts, as evident, for example, in the Zagros Mountains or in the Swiss Alps, remain largely unknown. Previous work has suggested that such variations in orogenic structure may be explained by the thermotectonic "age" of the deforming lithosphere and hence its rheology. Here we demonstrate that sediment loading of the foreland basin area provides an additional control and may explain the variable basement involvement in orogenic belts. When examining the role of sedimentation, we identify two end-members: (1) sediment-starved orogenic systems with thick-skinned basement deformation in an axial orogenic core and thin-skinned deformation in the bordering forelands and (2) sediment-loaded orogens with thick packages of synorogenic deposits, derived from the axial basement zone, deposited on the surrounding foreland fold-and-thrust belts, and characterized by basement deformation below the foreland. Using high-resolution thermomechanical models, we demonstrate a strong feedback between deposition and crustal-scale thick-skinned deformation. Our results show that the loading effects of syntectonic sediments lead to long crustal-scale thrust sheets beneath the orogenic foreland and explain the contrasting characteristics of sediment-starved and sediment-loaded orogens, showing for the first time how both thin- and thick-skinned crustal deformations are linked to sediment deposition in these orogenic systems. We show that the observed model behavior is consistent with observations from a number of natural orogenic systems.

Structural analysis using thrust-fault hanging-wall sequence diagrams: Ogden duplex, Wasatch Range, Utah

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schirmer, T.W.

1988-05-01

Detailed mapping and cross-section traverses provide the control for structural analysis and geometric modeling of the Ogden duplex, a complex thrust system exposed in the Wasatch Mountains, east of Ogden, Utah. The structures consist of east-dipping folded thrust faults, basement-cored horses, lateral ramps and folds, and tear faults. The sequence of thrusting determined by means of lateral overlap of horses, thrust-splay relationships, and a top-to-bottom piggyback development is Willard thrust, Ogden thrust, Weber thrust, and Taylor thrust. Major decollement zones occur in the Cambrian shales and limestones. The Tintic Quartzite is the marker for determining gross geometries of horses. Thismore » exposed duplex serves as a good model to illustrate the method of constructing a hanging-wall sequence diagram - a series of longitudinal cross sections that move forward in time and space, and show how a thrust system formed as it moved updip over various footwall ramps. A hanging wall sequence diagram also shows the complex lateral variations in a thrust system and helps to locate lateral ramps, lateral folds, tear faults, and other features not shown on dip-oriented cross sections. 8 figures.« less

Significance of the precambrian basement and late Cretaceous thrust nappes on the location of tertiary ore deposits in the Oquirrh Mountains, Utah

USGS Publications Warehouse

Tooker, Edwin W.

2005-01-01

The Oquirrh Mountains are located in north central Utah, in the easternmost part of the Basin and Range physiographic province, immediately south of the Great Salt Lake. The range consists of a northerly trending alignment of peaks 56 km long. Tooele and Rush Valleys flank the Oquirrh Mountains on the western side and Salt Lake and Cedar Valleys lie on the eastern side. The world class Bingham mine in the central part of the range hosts disseminated copper-bearing porphyry, skarn, base-and precious-metal vein and replacement ore deposits. The district includes the outlying Barneys Canyon disseminated-gold deposits. Disseminated gold in the Mercur mining district in the southern part of the range has become exhausted. The Ophir and Stockton base- and precious-metal mining districts in the range north of Mercur also are inactive. A geologic map of the range (Tooker and Roberts, 1998), available at a scale of 1:50,000, is a summation of U.S. Geological Survey (USGS) studies. Information about the range and its mining areas is scattered. This report summarizes map locations, new stratigraphic and structural data, and reexamined data from an extensive published record. Unresolved controversial geological interpretations are considered, and, for the first time, the complete geological evidence provides a consistent regional basis for the location of the ore deposits in the range. The geological setting and the siting of mineral deposits in the Oquirrh Mountains began with the formation of a Precambrian craton. Exposures of folded Proterozoic basement rocks of the craton, in the Wasatch Mountains east of Salt Lake City, were accreted and folded onto an Archean crystalline rock terrane. The accretion suture lies along the north flank of the Uinta Mountains. The western part of the accreted block was offset to northern Utah along a north-trending fault lying approximately along the Wasatch Front (Nelson and others, 2002), thereby creating a prominant basement barrier or buttress east of the Salt Lake area. The accretion suture along the north flank of the Uinta Anticline overlaps an earlier Precambrian east-west mobile zone, the Uinta trend (Erickson, 1976, Bryant and Nichols, 1988 and John, 1989), which extends westward across western Utah and into Nevada. A trace of the trend underlies the middle part of the Oquirrh Mountains. Its structure is recognized by disrupted Paleozoic stratigraphic units and fold and fault evidence of thrust faulting, intermittent local uplift and erosion, the alignment of Tertiary intrusives and associated ore deposits. Geologic readjustments along the trend continued intermittently through the Paleozoic, Cenozoic, Tertiary, and the development of clastic deposits along the shores of Pleistocene Lake Bonneville. Paleozoic sedimentary rocks were deposited on the craton platform shelf in westernmost Utah and eastern Nevada as the shelf subsided gradually and differentially. Debris was shed into two basins separated by the uplifted Uinta trend, the Oquirrh Basin on the south and Sublette Basin on the north. Sediments were derived from the craton to the east, the Antler orogenic zone on the west (Roberts, 1964), and locally from uplifted parts of the trend itself. Thick accumulations of clastic calcareous quartzite, shale, limestone, and dolomite of Lower and Upper Paleozoic ages are now exposed in the Oquirrh Mountains, the result of thrust faults. Evidence of decollement thrust faults in in the Wasatch Mountains during the Late Cretaceous Sevier orogeny, recognized by Baker and others (1949) and Crittenden (1961, is also recognized in the Oquirrh Mountains by Roberts and others (1965). During the late Cretaceous Sevier Orogeny, nappes were thrust sequentially along different paths from their western hinterland to the foreland. Five distinct nappes converged over the Uinta trend onto an uplifted west-plunging basement buttress east of the Oquirrh Mountains area: the Pass Canyon, Bingham,

Geologic map of the greater Denver area, Front Range urban corridor, Colorado

USGS Publications Warehouse

Trimble, Donald E.; Machette, Michael N.

1979-01-01

This digital map shows the areal extent of surficial deposits and rock stratigraphic units (formations) as compiled by Trimble and Machette from 1973 to 1977 and published in 1979 under the Front Range Urban Corridor Geology Program. Trimble and Machette compiled their geologic map from published geologic maps and unpublished geologic mapping having varied map unit schemes. A convenient feature of the compiled map is its uniform classification of geologic units that mostly matches those of companion maps to the north (USGS I-855-G) and to the south (USGS I-857-F). Published as a color paper map, the Trimble and Machette map was intended for land-use planning in the Front Range Urban Corridor. This map recently (1997-1999) was digitized under the USGS Front Range Infrastructure Resources Project. In general, the mountainous areas in the western part of the map exhibit various igneous and metamorphic bedrock units of Precambrian age, major faults, and fault brecciation zones at the east margin (5-20 km wide) of the Front Range. The eastern and central parts of the map (Colorado Piedmont) depict a mantle of unconsolidated deposits of Quaternary age and interspersed outcroppings of Cretaceous or Tertiary-Cretaceous sedimentary bedrock. The Quaternary mantle comprises eolian deposits (quartz sand and silt), alluvium (gravel, sand, and silt of variable composition), colluvium, and a few landslides. At the mountain front, north-trending, dipping Paleozoic and Mesozoic sandstone, shale, and limestone bedrock formations form hogbacks and intervening valleys.

Water, energy, and biogeochemical budgets investigation at Panola Mountain research watershed, Stockbridge, Georgia; a research plan

USGS Publications Warehouse

Huntington, T.G.; Hooper, R.P.; Peters, N.E.; Bullen, T.D.; Kendall, Carol

1993-01-01

The Panola Mountain Research Watershed (PMRW), located in the Panola Mountain State Conservation Park near Stockbridge, Georgia has been selected as a core research watershed under the Water, Energy and Biogeochemical Budgets (WEBB) research initiative of the U.S. Geological Survey (USGS) Global Climate Change Program. This research plan describes ongoing and planned research activities at PMRW from 1984 to 1994. Since 1984, PMRW has been studied as a geochemical process research site under the U.S. Acid Precipitation Thrust Program. Research conducted under this Thrust Program focused on the estimation of dry atmospheric deposition, short-term temporal variability of streamwater chemistry, sulfate adsorption characteristics of the soils, groundwater chemistry, throughfall chemistry, and streamwater quality. The Acid Precipitation Thrust Program continues (1993) to support data collection and a water-quality laboratory. Proposed research to be supported by the WEBB program is organized in 3 interrelated categories: streamflow generation and water-quality evolution, weathering and geochemical evolution, and regulation of soil-water chemistry. Proposed research on streamflow generation and water-quality evolution will focus on subsurface water movement, its influence in streamflow generation, and the associated chemical changes of the water that take place along its flowpath. Proposed research on weathering and geochemical evolution will identify the sources of cations observed in the streamwater at Panola Mountain and quantify the changes in cation source during storms. Proposed research on regulation of soil-water chemistry will focus on the poorly understood processes that regulate soil-water and groundwater chemistry. (USGS)

SHEEP MOUNTAIN WILDERNESS STUDY AREA, WYOMING.

USGS Publications Warehouse

Houston, Robert S.; Patten, Lowell L.

1984-01-01

On the basis of a mineral survey the Sheep Mountain Wilderness study area in Wyoming was determined to offer little promise for metallic mineral resources. There is a probable potential for oil and gas resources in a small part of the study area along its northeast margin. Geophysical studies, such as reflection seismic profiling would help define the oil and gas potential in fault-controlled structures, such as those beneath the thrust fault that crops out along the east flank of Sheep Mountain.

Crustal implications of bedrock geology along the Trans-Alaska Crustal Transect (TACT) in the Brooks Range, northern Alaska

USGS Publications Warehouse

Moore, Thomas E.; Wallace, W.K.; Mull, C.G.; Adams, K.E.; Plafker, G.; Nokleberg, W.J.

1997-01-01

Geologic mapping of the Trans-Alaska Crustal Transect (TACT) project along the Dalton Highway in northern Alaska indicates that the Endicott Mountains allochthon and the Hammond terrane compose a combined allochthon that was thrust northward at least 90 km in the Early Cretaceous. The basal thrust of the combined allochthon climbs up section in the hanging wall from a ductile shear zone, in the south through lower Paleozoic rocks of the Hammond terrane and into Upper Devonian rocks of the Endicott Mountains allochthon at the Mount Doonerak antiform, culminating in Early Cretaceous shale in the northern foothills of the Brooks Range. Footwall rocks north of the Mount Doonerak antiform are everywhere parautochthonous Permian and Triassic shale of the North Slope terrane rather than Jurassic and Lower Cretaceous strata of the Colville Basin as shown in most other tectonic models of the central Brooks Range. Stratigraphic and structural relations suggest that this thrust was the basal detachment for Early Cretaceous deformation. Younger structures, such as the Tertiary Mount Doonerak antiform, deform the Early Cretaceous structures and are cored by thrusts that root at a depth of about 10 to 30 km along a deeper detachment than the Early Cretaceous detachment. The Brooks Range, therefore, exposes (1) an Early Cretaceous thin-skinned deformational belt developed during arc-continent collision and (2) a mainly Tertiary thick-skinned orogen that is probably the northward continuation of the Rocky Mountains erogenic belt. A down-to-the-south zone of both ductile and brittle normal faulting along the southern margin of the Brooks Range probably formed in the mid-Cretaceous by extensional exhumation of the Early Cretaceous contractional deformation. copyright. Published in 1997 by the American Geophysical Union.

Contractional deformation of porous sandstone: Insights from the Aztec Sandstone, SE Nevada, USA

NASA Astrophysics Data System (ADS)

Fossen, Haakon; Zuluaga, Luisa F.; Ballas, Gregory; Soliva, Roger; Rotevatn, Atle

2015-05-01

Contractional deformation of highly porous sandstones is poorly explored, as compared to extensional deformation of such sedimentary rocks. In this work we explore the highly porous Aztec Sandstone in the footwall to the Muddy Mountain thrust in SE Nevada, which contains several types of deformation bands in the Buffington tectonic window: 1) Distributed centimeter-thick shear-enhanced compaction bands (SECBs) and 2) rare pure compaction bands (PCBs) in the most porous parts of the sandstone, cut by 3) thin cataclastic shear-dominated bands (CSBs) with local slip surfaces. Geometric and kinematic analysis of the SECBs, the PCBs and most of the CSBs shows that they formed during ∼E-W (∼100) shortening, consistent with thrusting related to the Cretaceous to early Paleogene Sevier orogeny of the North American Cordilleran thrust system. Based on stress path modeling, we suggest that the compactional bands (PCBs and SECBs) formed during contraction at relatively shallow burial depths, before or at early stages of emplacement of the Muddy Mountains thrust sheet. The younger cataclastic shear bands (CSBs, category 3), also related to E-W Sevier thrusting, are thinner and show larger shear offsets and thus more intense cataclasis, consistent with the initiation of cataclastic shear bands in somewhat less porous materials. Observations made in this work support earlier suggestions that contraction lead to more distributed band populations than what is commonly found in the extensional regime, and that shear-enhanced compaction bands are widespread only where porosity (and permeability) is high.

Frontal compression along the Apennines thrust system: The Emilia 2012 example from seismicity to crustal structure

NASA Astrophysics Data System (ADS)

Chiarabba, Claudio; De Gori, Pasquale; Improta, Luigi; Lucente, Francesco Pio; Moretti, Milena; Govoni, Aladino; Di Bona, Massimo; Margheriti, Lucia; Marchetti, Alessandro; Nardi, Anna

2014-12-01

The evolution of the Apennines thrust-and-fold belt is related to heterogeneous process of subduction and continental delamination that generates extension within the mountain range and compression on the outer front of the Adria lithosphere. While normal faulting earthquakes diffusely occur along the mountain chain, the sparse and poor seismicity in the compressional front does not permit to resolve the ambiguity that still exists about which structure accommodates the few mm/yr of convergence observed by geodetic data. In this study, we illustrate the 2012 Emilia seismic sequence that is the most significant series of moderate-to-large earthquakes developed during the past decades on the compressional front of the Apennines. Accurately located aftershocks, along with P-wave and Vp/Vs tomographic models, clearly reveal the geometry of the thrust system, buried beneath the Quaternary sediments of the Po Valley. The seismic sequence ruptured two distinct adjacent thrust faults, whose different dip, steep or flat, accounts for the development of the arc-like shape of the compressional front. The first shock of May 20 (Mw 6.0) developed on the middle Ferrara thrust that has a southward dip of about 30°. The second shock of May 29 (Mw 5.8) ruptured the Mirandola thrust that we define as a steep dipping (50-60°) pre-existing (Permo-Triassic) basement normal fault inverted during compression. The overall geometry of the fault system is controlled by heterogeneity of the basement inherited from the older extension. We also observe that the rupture directivity during the two main-shocks and the aftershocks concentration correlate with low Poisson ratio volumes, probably indicating that portions of the fault have experienced intense micro-damage.

Uplifting model of the Longmenshan mountain in the eastern margin of Tibetan plateau

NASA Astrophysics Data System (ADS)

Zhang, S.; Ding, R.; Mao, C.

2010-12-01

Longmenshan mountain is a vivid manifestation of the Cenozoic orogenesis in the eastern margin of the Tibetan plateau, and a key to understand the geodynamics of eastward extending of the plateau. Thus the uplift mechanism of Longmenshan mountain became a hot spot issue of geosciences about the Tibetan plateau. Two entirely different hypotheses, i.e., crustal shortening and lower crustal channel flow, were put forward, but the solution is open. Further discussion need our deeper understanding about the uplifting features of the Longmenshan mountain. Fortunately, the uplifting processes were recorded objectively by peneplains and river landforms. We first analysed the peneplains and pediplanes of Longmenshan mountain and its surrounding areas, and surveyed the terraces of Dadu river running across the mountain. Then we studied the uplifting features of the study areas in late Cenozoic time on the basis of landform geometries. Finaly we discussed the possible mechanisms for the uplifting. There are two levels of peneplains whose peneplanations may begin in early Cenozoic time and end at late Miocene when the final fluctuations of elevations were possibly less than one kilometers. The valley of Dadu river is incised into the peneplains and has a staircase of no less than ten levels of terraces. The highest terrace is a strath which was contemporary with the pediplane in the piedmont formed in late Pliocene or in early Pleistocene. Due to their originally flat features, the peneplains and the strath terraces were used as datum planes for judging neotectonic deformations. Since late Miocene, the southeastern side of Longmenshan mountain has been dominated by thrust-faulting with a total vertical displacement of about 4500 m against the Sichuan basin, meantime the northwest side has been maintained flexural uplift with syncline hinge approximately following the Longriba fault. As a landform barrier between Tibetan plateau and Sichuan basin, the crest lines of the mountain are about 500 to 1000 m higher than the hinterland surface on the west side. In a word, Longmenshan mountain has been formed by the combination of eastern-wing thrusting and west-wing flexing which are attested by the deformation of the Tertiary peneplains and the longitudinal profiles of Quaternary strath terraces of Dadu river. The possible mechanisms for the uplifting of the mountain are the fault-bend folding of the upper crust, the upwelling of plastic lower crust , and crustal isostasy induced by surface erosion. In the light of the existence of longitudinal thrust faults or reversely strike-slip fault along the eastern and western wings of Longmenshan mountain, and no finding of longitudinal extensional faults there, fault-bend folding is proposed to be the leading factor.

Permian deposition in the north central Brooks Range, Alaska Constraints for tectonic reconstructions

USGS Publications Warehouse

Adams, K.E.; Mull, C.G.; Crowder, R.K.

1997-01-01

Two opposing tectonic models have been offered to explain the regional structural relations in the north central Brooks Range fold-thrust belt of northern Alaska. The first suggests that rocks of the northern Endicott Mountains were thrust from south to north over the area of the present Mount Doonerak high and are therefore highly allochthonous. The second implies that the rocks of the northern Endicott Mountains were deposited in a basin that lay north of the Mount Doonerak high and later were thrust a short distance southward onto the northern flank of the high and are thus parautochthonous. To provide stratigraphic constraints for these models, this study examines Permian facies of the north central Brooks Range. Permian rocks in the north central Brooks Range comprise a thin (40 to 160 m thick), fining-upward succession of clastic, storm-influenced shelf deposits. When the rocks of the northern Endicott Mountains are restored south of the Mount Doonerak area, a minimum distance of 80 km, the Permian deposits grade systematically from distal facies (Siksikpuk Formation) in the southwest to proximal facies (Echooka Formation) in the northeast. Facies trends in the reconstructed Permian basin include, from southwest to northeast, (1) an increase in carbonate content and corresponding decrease in silica content, (2) a general darkening and thickening of shaley intervals, (3) an increase in proximal features of storm beds, including coarser, thicker, more abundant, and more closely spaced beds, and (4) an increase in abundance and diversity of the faunal assemblage with a corresponding decrease in age. These stratigraphic relations imply that rocks of the northern Endicott Mountains are allochthonous and structurally overlie a proximal stratigraphic succession similar to that exposed in the Mount Doonerak area and northeastern Brooks Range. Copyright 1997 by the American Geophysical Union.

Possible reactivation of the Vincent-Chocolate Mountains thrust in the Gavilan Hills area, southeasternmost California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oyarzabal, F.R.; Jacobson, C.E.; Haxel, G.B.

The Late Cretaceous-early Tertiary Orocopia Schist (OS) of southeasternmost California consists of metamorphosed continental margin sedimentary and basaltic rocks, overlain by an upper plate of continental crust along the Vincent-Chocolate Mountains fault (VCMF). Previous analysis of late folds and shear band in OS and upper plate in the Gavilan Hills and adjacent ares indicated that the direction of transport of the upper plate was northeastward. This has been considered evidence of a SW dipping subduction zone, along which an outboard continental fragment was sutured to North America. Another view is that the VCMF was formed by underplating of the OSmore » in an Andean continental margin, and that the NE-vergent late structures formed during uplift of the OS. The authors' continuing work in the Gavilan Hills confirm the NE sense of vergence but suggests a more complex structural history. The schist is characterized by refolded folds, shear bands, and two penetrative lineations. An older lineation that ranges from N10[degree]E to N30[degree]E is widespread in the area, but is more evident at low structural levels. A second lineation ranges from N40[degree]E to N70[degree]E and is strongly developed in rocks near the VCMF. The complex folding pattern, presence of mylonitic schist, relative thinness of upper-plate mylonite, and possible retrogressive character of the shear bands suggest that the VCMF in the Gavilan Hills area may have been reactivated after original thrusting. The VCMF in the Gavilan Hills is intermediate in character between the probable subduction thrust in the San Gabriel Mountains and the reactivated faults in the Orocopia Mountains and areas surrounding the Gavilan Hills.« less

Engineering Design Handbook. Military Vehicle

DTIC Science & Technology

1998-05-01

C0NNECTIN6 NOD HEARINGS. CAMSHAFT BEARINGS. AND VALVE THAIH PRESSURE REGULATOR VALVE SB PSI sc OIL PAH SCAVENGE PUMP INLET SCREEN Figure 1-6...to 40 percent, hogbacks, ditches, racks, embankments, random log obstacles, brush, tree stumps, dust, and mud. Most vehicles have requirements for

Exhumation history of the West Kunlun Mountains, northwestern Tibet: Evidence for a long-lived, rejuvenated orogen

NASA Astrophysics Data System (ADS)

Cao, Kai; Wang, Guo-Can; Bernet, Matthias; van der Beek, Peter; Zhang, Ke-Xin

2015-12-01

How and when the northwestern Tibetan Plateau originated and developed upon pre-existing crustal and topographic features is not well understood. To address this question, we present an integrated analysis of detrital zircon U-Pb and fission-track double dating of Cenozoic synorogenic sediments from the Kekeya and Sanju sections in the southwestern Tarim Basin. These data help establishing a new chronostratigraphic framework for the Sanju section and confirm a recent revision of the chronostratigraphy at Kekeya. Detrital zircon fission-track ages present prominent Triassic-Early Jurassic (∼250-170 Ma) and Early Cretaceous (∼130-100 Ma) static age peaks, and Paleocene-Early Miocene (∼60-21 Ma) to Eocene-Late Miocene (∼39-7 Ma) moving age peaks, representing source exhumation. Triassic-Early Jurassic static peak ages document unroofing of the Kunlun terrane, probably related to the subduction of Paleotethys oceanic lithosphere. In combination with the occurrence of synorogenic sediments on both flanks of the Kunlun terrane, these data suggest that an ancient West Kunlun range had emerged above sea level by Triassic-Early Jurassic times. Early Cretaceous fission-track peak ages are interpreted to document exhumation related to thrusting along the Tam Karaul fault, kinematically correlated to the Main Pamir thrust further west. Widespread Middle-Late Mesozoic crustal shortening and thickening likely enhanced the Early Mesozoic topography. Paleocene-Early Eocene fission-track peak ages are presumably partially reset. Limited regional exhumation indicates that the Early Cenozoic topographic and crustal pattern of the West Kunlun may be largely preserved from the Middle-Late Mesozoic. The Main Pamir-Tam Karaul thrust belt could be a first-order tectonic feature bounding the northwestern margin of the Middle-Late Mesozoic to Early Cenozoic Tibetan Plateau. Toward the Tarim basin, Late Oligocene-Early Miocene steady exhumation at a rate of ∼0.9 km/Myr is likely related to initial thrusting of the Tiklik fault and reactivation of the Tam Karaul thrust. Thrusting together with upper crustal shortening in the mountain front indicates basinward expansion of the West Kunlun orogen at this time. This episode of exhumation and uplift, associated with magmatism across western Tibet, is compatible with a double-sided lithospheric wedge model, primarily driven by breakoff of the Indian crustal slab. Accelerated exhumation of the mountain front at a rate of ∼1.1 km/Myr since ∼15 Ma supports active compressional deformation at the margins of the northwestern Tibetan Plateau. We thus propose that the West Kunlun Mountains are a long-lived topographic unit, dating back to Triassic-Early Jurassic times, and have experienced Middle-Late Mesozoic to Early Cenozoic rejuvenation and Late Oligocene-Miocene expansion.

Ordovician and Silurian Phi Kappa and Trail Creek formations, Pioneer Mountains, central Idaho; stratigraphic and structural revisions, and new data on graptolite faunas

USGS Publications Warehouse

Dover, James H.; Berry, William B.N.; Ross, Reuben James

1980-01-01

Recent geologic mapping in the northern Pioneer Mountains combined with the identification of graptolites from 116 new collections indicate that the Ordovician and Silurian Phi Kappa and Trail Creek Formations occur in a series of thrust-bounded slices within a broad zone of imbricate thrust faulting. Though confirming a deformational style first reported in a 1963 study by Michael Churkin, our data suggest that the complexity and regional extent of the thrust zone were not previously recognized. Most previously published sections of the Phi Kappa and Trail Creek Formations were measured across unrecognized thrust faults and therefore include not only structural repetitions of graptolitic Ordovician and Silurian rocks but also other tectonically juxtaposed lithostratigraphic units of diverse ages as well. Because of this discovery, the need to reconsider the stratigraphic validity of these formations and their lithology, nomenclature, structural distribution, facies relations, and graptolite faunas has arisen. The Phi Kappa Formation in most thrust slices has internal stratigraphic continuity despite the intensity of deformation to which it was subjected. As revised herein, the Phi Kappa Formation is restricted to a structurally repeated succession of predominantly black, carbonaceous, graptolitic argillite and shale. Some limy, light-gray-weathering shale occurs in the middle part of the section, and fine-grained locally pebbly quartzite is present at the base. The basal quartzite is here named the Basin Gulch Quartzite Member of the Phi Kappa. The Phi Kappa redefined on a lithologic basis represents the span of Ordovician time from W. B. N. Berry's graptolite zones 2-4 through 15 and also includes approximately 17 m of lithologically identical shale of Early and Middle Silurian age at the top. The lower contact of the formation as revised is tectonic. The Phi Kappa is gradationally overlain by the Trail Creek Formation as restricted herein. Most of the coarser clastic rocks reported in previously measured sections of the Phi Kappa, as well as the sequence along Phi Kappa Creek from which the name originates, are excluded from the Phi Kappa as revised and are reassigned to two structural plates of Mississippian Copper Basin Formation; other strata now excluded from the formation are reassigned to the Trail Creek Formation and to an unnamed Silurian and Devonian unit. As redefined, the Phi Kappa Formation is only about 240 m thick, compared with the 3,860 m originally estimated, and it occupies only about 25 percent of the outcrop area previously mapped in 1930 by H. G. Westgate and C. P. Ross. Despite this drastic reduction in thickness and the exclusion of the rocks along Phi Kappa Creek, the name Phi Kappa is retained because of widely accepted prior usage to denote the Ordovician graptolitic shale facies of central Idaho, and because the Phi Kappa Formation as revised is present in thrust slices on Phi Kappa Mountain, at the head of Phi Kappa Creek. The lithic and faunal consistency of this unit throughout the area precludes the necessity for major facies telescoping along individual faults within the outcrop belt. However, tens of kilometers of tectonic shortening seems required to juxtapose the imbricated Phi Kappa shale facies with the Middle Ordovician part of the carbonate and quartzite shale sequence of east central Idaho. The shelf rocks are exposed in the Wildhorse structural window of the northeastern Pioneer Mountains, and attain a thickness of at least 1,500 m throughout the region north and east of the Pioneer Mountains. The Phi Kappa is in direct thrust contact on intensely deformed medium- to high-grade metamorphic equivalents of the same shelf sequence in the Pioneer window at the south end of the Phi Kappa-Trail Creek outcrop belt. Along East Pass, Big Lake, and Pine Creeks, north of the Pioneer Mountains, some rocks previously mapped as Ramshorn Slate are lithologically and faunally equivalent to the P

Interseismic coupling, seismic potential and earthquake recurrence on the southern front of the Eastern Alps (NE Italy)

NASA Astrophysics Data System (ADS)

Cheloni, Daniele; D'Agostino, Nicola; Selvaggi, Giulio

2014-05-01

The interaction of the African, Arabian, and Eurasia plates in the "greater" Mediterranean region yields to a broad range of tectonic processes including active subduction, continental collision, major continental strike-slip faults and "intra-plate" mountain building. In this puzzling region the convergence between Adria microplate and Eurasia plate is partly or entirely absorbed within the South-Eastern Alps, where the Adriatic lithosphere underthrusts beneath the mountain belt. Historical seismicity and instrumentally recorded earthquakes show thrust faulting on north-dipping low-angle faults in agreement with geological observations of active mountain building and active fold growing at the foothills of the South-Eastern Alps. In this study, we use continuous GPS observations to document the geodetic strain accumulation across the South-Eastern Alps (NE Italy). We estimate the pattern of interseismic coupling on the intra-continental collision north-dipping thrust faults that separate the Eastern Alps and the Venetian-Friulian plain using the back-slip approach and discuss the seismic potential and earthquake recurrence. Comparison between the rigid-rotation predicted motion and the shortening observed across the studied area indicates that the South-Eastern Alpine thrust front absorbs about 80% of the total convergence rate between the Adria microplate and Eurasia plate. The modelled thrust fault is currently locked from the surface to a depth of approximately 10 km. The transition zone between locked and creeping portions of the fault roughly corresponds with the belt of microseismicity parallel and to the north of the mountain front. The estimated moment deficit rate is 1.27±0.14×10^17 Nm/yr. The comparison between the estimated moment deficit and that released historically by the earthquakes suggests that to account for the moment deficit the following two factors or their combination should be considered: (1) a significant part of the observed interseismic coupling is released aseismically by folding or creeping; (2) infrequent "large" events with long return period (>1000 years) and with magnitudes larger than the value assigned to the largest historical events (Mw≡6.7).

Correlation chart of Pennsylvanian rocks in Alabama, Tennessee, Kentucky, Virginia, West Virginia, Ohio, Maryland, and Pennsylvania showing approximate position of coal beds, coal zones, and key stratigraphic units: Chapter D.2 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

USGS Publications Warehouse

Ruppert, Leslie F.; Trippi, Michael H.; Slucher, Ernie R.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

Because of the many names used to identify individual coal beds and coal zones in the historic Appalachian basin coal-mining districts, coal bed designations may differ even more than stratigraphic nomenclature. In eastern Kentucky, northwest of the Pine Mountain thrust fault on the Cumberland overthrust sheet, for example, coal beds or coal zones equivalent to the Lower Elkhorn coal zone (within the Pikeville Formation) are identified also as the Eagle coal zone, Pond Creek coal zone, and Blue Gem coal bed (fig. 1). Southeast of the Pine Mountain thrust fault, yet still in Kentucky, equivalent coals in this same interval are known as the Imboden and Rich Mountain. Moreover, this same interval of coal is identified as the Blue Gem coal in Tennessee, the Imboden coal bed or Campbell Creek or Pond Creek coal zones in Virginia, and the Eagle coal zone in West Virginia.

Geophysical interpretations west of and within the northwestern part of the Nevada Test Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grauch, V.J.; Sawyer, D.A.; Fridrich, C.J.

1997-12-31

This report focuses on interpretation of gravity and new magnetic data west of the Nevada Test Site (NTS) and within the northwestern part of NTS. The interpretations integrate the gravity and magnetic data with other geophysical, geological, and rock property data to put constraints on tectonic and magmatic features not exposed at the surface. West of NTS, where drill hole information is absent, these geophysical data provide the best available information on the subsurface. Interpreted subsurface features include calderas, intrusions, basalt flows and volcanoes, Tertiary basins, structurally high pre-Tertiary rocks, and fault zones. New features revealed by this study includemore » (1) a north-south buried tectonic fault east of Oasis Mountain, which the authors call the Hogback fault; (2) an east striking fault or accommodation zone along the south side of Oasis Valley basin, which they call the Hot Springs fault; (3) a NNE striking structural zone coinciding with the western margins of the caldera complexes; (4) regional magnetic highs that probably represent a thick sequence of Tertiary volcanic rocks; and (5) two probable buried calderas that may be related to the tuffs of Tolicha Peak and of Sleeping Butte, respectively.« less

A spatial database of bedding attitudes to accompany Geologic map of the greater Denver area, Front Range Urban Corridor, Colorado

USGS Publications Warehouse

Trimble, Donald E.; Machette, Michael N.; Brandt, Theodore R.; Moore, David W.; Murray, Kyle E.

2003-01-01

This digital map shows bedding attitude symbols display over the geographic extent of surficial deposits and rock stratigraphic units (formations) as compiled by Trimble and Machette 1973-1977 and published in 1979 (U.S. Geological Survey Map I-856-H) under the Front Range Urban Corridor Geology Program. Trimble and Machette compiled their geologic map from published geologic maps and unpublished geologic mapping having varied map unit schemes. A convenient feature of the compiled map is its uniform classification of geologic units that mostly matches those of companion maps to the north (USGS I-855-G) and to the south (USGS I-857-F). Published as a color paper map, the Trimble and Machette map was intended for land-use planning in the Front Range Urban Corridor. This map recently (1997-1999), was digitized under the USGS Front Range Infrastructure Resources Project (see cross-reference). In general, the mountainous areas in the west part of the map exhibit various igneous and metamorphic bedrock units of Precambrian age, major faults, and fault brecciation zones at the east margin (5-20 km wide) of the Front Range. The eastern and central parts of the map (Colorado Piedmont) depict a mantle of unconsolidated deposits of Quaternary age and interspersed outcroppings of Cretaceous or Tertiary-Cretaceous sedimentary bedrock. The Quaternary mantle is comprised of eolian deposits (quartz sand and silt), alluvium (gravel, sand, and silt of variable composition), colluvium, and few landslides. At the mountain front, north-trending, dipping Paleozoic and Mesozoic sandstone, shale, and limestone bedrock formations form hogbacks and intervening valleys.

Geologic map of the Horse Mountain Quadrangle, Garfield County, Colorado

USGS Publications Warehouse

Perry, W.J.; Shroba, R.R.; Scott, R.B.; Maldonado, Florian

2003-01-01

New 1:24,000-scale geologic map of the Horse Mountain 7.5' quadrangle, in support of the USGS Western Colorado I-70 Corridor Cooperative Geologic Mapping Project, summarizes available geologic information for the quadrangle. It provides new interpretations of the stratigraphy, structure, and geologic hazards in the area of the southwest flank of the White River uplift. Bedrock strata include the Paleocene and early Eocene Wasatch Formation down through Ordovician and Cambrian units into Precambrian hornblende tonalite. The Wasatch Formation includes the Shire, Molina and Atwell Gulch Members which are mapped separately. The underlying Upper Cretaceous Mesaverde Group is subdivided into the Willams Fork and Iles Formations. The Cameo-Fairfield clinker zone within the Williams Fork Formation is mapped separately. The Iles Formation includes the Rollins Sandstone Member at the top, mapped separately, and the Cozzette Sandstone and Corcoran Sandstone Members, which are undivided. The Mancos Shale consists of four members, an upper member, the Niobrara Member, the Juana Lopez Member, and a lower member, undivided. The Lower Cretaceous Dakota Sandstone, the Upper Jurassic Morrison Formation, and Jurassic Entrada Sandstone are mapped separately. The Lower Jurassic and Upper Triassic Glen Canyon Sandstone is mapped with the Entrada in the Horse Mountain Quadrangle. The upper Triassic Chinle Formation and the Lower Permian and Triassic(?) State Bridge Formation are present. The Pennsylvanian and Permian Maroon Formation is undivided. All the exposures of the Middle Pennsylvanian Eagle Valley Evaporite are diapiric, intruded into the Middle Pennsylvanian Eagle Valley Formation, which includes locally mappable limestone beds. The Lower and Middle Pennsylvanian Belden Formation and the Lower Mississippian Leadville Limestone are present. The Upper Devonian Chaffee Group consists of the Dyer Dolomite and the underlying Parting Quartzite, undivided. Locally, the Lower Ordovician Manitou Formation is mapped separately beneath the Chaffee. Elsewhere, Ordovician through Cambrian units, the Manitou and Dotsero Formations, underlain by the Sawatch Quartzite, are undivided. The southwest flank of the White River uplift is a late Laramide structure that is represented by the steeply southwest-dipping Grand Hogback, which is only present in the southwestern corner of the map area, and less steeply southwest-dipping older strata that flatten to nearly horizontal attitudes in the northern part of the map area. Between these two are a complex of normal faults, the largest of which dips southward placing Chafee dolostone and Leadville Limestone adjacent to Eagle Valley and Maroon Formations. Diapiric Eagle Valley Evaporite intruded close to the fault on the down-thrown side. Removal of evaporite by either flow or dissolution from under younger parts of the strata create structural benches, folds, and sink holes on either side of the normal fault. A prominent dipslope of the Morrison-Dakota-Mancos part of the section forms large slide blocks and mass movement deposits consisting of a chaos of admixed Morrison and Dakota lithologies. The major geologic hazard in the area consists of large landslides both associated with dip-slope slide blocks and the steep slopes of the Eagle Valley Formation and Belden Formation in the northern part of the map. Abandoned coal mines are present along the north face of the Grand Hogback in the lower part of the Mesaverde Group

Structural Mapping of Paterae and Mountains on Io: Implications for Crustal Stresses and Feature Evolution

NASA Astrophysics Data System (ADS)

Ahern, A.; Radebaugh, J.; Christiansen, E. H.; Harris, R. A.

2015-12-01

Paterae and mountains are some of the most distinguishing and well-distributed surface features on Io, and they reveal the role of tectonism in Io's crust. Paterae, similar to calderas, are volcano-tectonic collapse features that often have straight margins. Io's mountains are some of the highest in the solar system and contain linear features that reveal crustal stresses. Paterae and mountains are often found adjacent to one another, suggesting possible genetic relationships. We have produced twelve detailed regional structural maps from high-resolution images of relevant features, where available, as well as a global structural map from the Io Global Color Mosaic. The regional structural maps identify features such as fractures, lineations, folds, faults, and mass wasting scarps, which are then interpreted in the context of global and regional stress regimes. A total of 1048 structural lineations have been identified globally. Preliminary analyses of major thrust and normal fault orientations are dominantly 90° offset from each other, suggesting the maximum contractional stresses leading to large mountain formation are not a direct result of tidal extension. Rather, these results corroborate the model of volcanic loading of the crust and global shortening, leading to thrust faulting and uplift of coherent crustal blocks. Several paterae, such as Hi'iaka and Tohil, are found adjacent to mountains inside extensional basins where lava has migrated up normal faults to erupt onto patera floors. Over time, mass wasting and volcanic resurfacing can change mountains from young, steep, and angular peaks to older, gentler, and more rounded hills. Mass wasting scarps make up 53% of all features identified. The structural maps highlight the significant effect of mass wasting on Io's surface, the evolution of mountains through time, the role of tectonics in the formation of paterae, and the formation of mountains through global contraction due to volcanism.

1957 Gobi-Altay, Mongolia, earthquake as a prototype for southern California's most devastating earthquake

USGS Publications Warehouse

Bayarsayhan, C.; Bayasgalan, A.; Enhtuvshin, B.; Hudnut, K.W.; Kurushin, R.A.; Molnar, P.; Olziybat, M.

1996-01-01

The 1957 Gobi-Altay earthquake was associated with both strike-slip and thrust faulting, processes similar to those along the San Andreas fault and the faults bounding the San Gabriel Mountains just north of Los Angeles, California. Clearly, a major rupture either on the San Andreas fault north of Los Angeles or on the thrust faults bounding the Los Angeles basin poses a serious hazard to inhabitants of that area. By analogy with the Gobi-Altay earthquake, we suggest that simultaneous rupturing of both the San Andreas fault and the thrust faults nearer Los Angeles is a real possibility that amplifies the hazard posed by ruptures on either fault system separately.

Thin‐ or thick‐skinned faulting in the Yakima fold and thrust belt (WA)? Constraints from kinematic modeling of the saddle mountains anticline

USGS Publications Warehouse

Casale, Gabriele; Pratt, Thomas L.

2015-01-01

The Yakima fold and thrust belt (YFTB) deforms the Columbia River Basalt Group flows of Washington State. The YFTB fault geometries and slip rates are crucial parameters for seismic‐hazard assessments of nearby dams and nuclear facilities, yet there are competing models for the subsurface fault geometry involving shallowly rooted versus deeply rooted fault systems. The YFTB is also thought to be analogous to the evenly spaced wrinkle ridges found on other terrestrial planets. Using seismic reflection data, borehole logs, and surface geologic data, we tested two proposed kinematic end‐member thick‐ and thin‐skinned fault models beneath the Saddle Mountains anticline of the YFTB. Observed subsurface geometry can be produced by 600–800 m of heave along a single listric‐reverse fault or ∼3.5  km of slip along two superposed low‐angle thrust faults. Both models require decollement slip between 7 and 9 km depth, resulting in greater fault areas than sometimes assumed in hazard assessments. Both models require initial slip much earlier than previously thought and may provide insight into the subsurface geometry of analogous comparisons to wrinkle ridges observed on other planets.

Folding kinematics expressed in fracture patterns: An example from the Anti-Atlas fold belt, Morocco

NASA Astrophysics Data System (ADS)

Ismat, Zeshan

2008-11-01

The Anti-Atlas fold belt, Morocco, formed during the same Variscan collisional event that produced the Valley-and-Ridge fold-thrust belt of the Appalachian mountains. Both are external belts of the Appalachian-Ouachita-Mauritanides chain and at the map scale have very similar topographic expressions. The Anti-Atlas, however, consists of map-scale folds that are buckle-related, detachment folds, whereas the Valley-and-Ridge folds developed in response to imbricate thrusting. For this reason, the Anti-Atlas is referred to as a fold belt rather than a fold-thrust belt. This paper examines Variscan folding processes in the Anti-Atlas Mountains. Folding in some layers occurred by sliding along a penetrative network of mesoscale fractures, i.e. cataclastic flow, during buckling. Layer-parallel shortening fractures were reactivated in the later stages of folding to accommodate limb rotation. Although 'boutonnieres', i.e. basement uplifts, punctuate the fold belt, the fracture patterns indicate that the uplifts failed to provide any 'bending' component. Folding is also interpreted to occur under low to moderate confining pressures because the fracture network includes conjugate shear fractures with very small (˜20°) dihedral angles.

How to build the Eiger: Surface expression of litho-tectonic preconditioning

NASA Astrophysics Data System (ADS)

Mair, David; Lechmann, Alessandro; Schlunegger, Fritz

2017-04-01

The north face of the Eiger has exerted a strong attraction on alpinists, but also on geologists during the past decades, mainly because of its triangular, nearly vertical shape. We build on this tradition and investigate the relationship between the shape of this mountain and its underlying lithology, and its history of folding and thrusting. To this extent, we constructed a geometric 3D geological model of the Eiger-Moench-Jungfrau mountain chain in the central Swiss Alps. We proceeded through compilations of geological maps that we combined with new mapping in the field and collection of structural data such as the orientation of lineaments and faults. The model itself was constructed by interpolation of interfaces between geological formations, thrust- and fold-geometries between several NW-SE running, balanced, cross-sections. In addition, new geological data from the Jungfraubahn railway tunnel was used to verify surface data and improve the resulting model in the depth. The analyzed units of the Hercynian crystalline basement of the Aar massif and the Mesozoic cover rocks of the Helvetics form a foliated and thrusted stack. Multiple ductile structure sets bear witness of Alpine deformation and are dominant amid the mark of later brittle deformation across the whole mountain. There are two major outcomes of this analysis. First, the thrust contact between two stacks, which comprise a foliated basement and cover rocks, are responsible for the shape and overall architecture of the Eiger and its famous north face. Second, the high-resolution 3D structural model paired with petrological data shows that second-order, horizontally aligned morphological steps in the north face are related to the foliation within the bedrock. We suspect the inherited fabric significantly modified the susceptibility to erosion mechanisms which in turn further amplified the morphological differences (expressed in e.g. terrain roughness or slope).

Near-Surface and High Resolution Seismic Imaging of the Bennett Thrust Fault in the Indio Mountains of West Texas

NASA Astrophysics Data System (ADS)

Vennemann, Alan

My research investigates the structure of the Indio Mountains in southwest Texas, 34 kilometers southwest of Van Horn, at the UTEP (University of Texas at El Paso) Field Station using newly acquired active-source seismic data. The area is underlain by deformed Cretaceous sedimentary rocks that represent a transgressive sequence nearly 2 km in total stratigraphic thickness. The rocks were deposited in mid Cretaceous extensional basins and later contracted into fold-thrust structures during Laramide orogenesis. The stratigraphic sequence is an analog for similar areas that are ideal for pre-salt petroleum reservoirs, such as reservoirs off the coasts of Brazil and Angola (Li, 2014; Fox, 2016; Kattah, 2017). The 1-km-long 2-D shallow seismic reflection survey that I planned and led during May 2016 was the first at the UTEP Field Station, providing critical subsurface information that was previously lacking. The data were processed with Landmark ProMAX seismic processing software to create a seismic reflection image of the Bennett Thrust Fault and additional imbricate faulting not expressed at the surface. Along the 1-km line, reflection data were recorded with 200 4.5 Hz geophones, using 100 150-gram explosive charges and 490 sledge-hammer blows for sources. A seismic reflection profile was produced using the lower frequency explosive dataset, which was used in the identification of the Bennett Thrust Fault and additional faulting and folding in the subsurface. This dataset provides three possible interpretations for the subsurface geometries of the faulting and folding present. However, producing a seismic reflection image with the higher frequency sledge-hammer sourced dataset for interpretation proved more challenging. While there are no petroleum plays in the Indio Mountains region, imaging and understanding subsurface structural and lithological geometries and how that geometry directs potential fluid flow has implications for other regions with petroleum plays.

Deformation of the Roberts Mountains Allochthon in north-central Nevada

USGS Publications Warehouse

Evans, James George; Theodore, Ted G.

1978-01-01

During the Antler orogeny in Late Devonian and Early Mississippian time, early and middle Paleozoic siliceous rocks, largely chert and sha1e, were thrust eastward for 90 to 160 km over coexisting carbonate rocks. Minor and major structures of two small areas of the allochthon at Battle Mountain and in the southern Tuscarora Mountains were studied in order to characterize the deformation and test the consistency of the movement plan with respect to the large eastward displacement. In the Battle Mountain area, the lower Paleozoic Scott Canyon and Valmy Formations were deformed in the Antler orogeny but were unaffected by later tectonism during late Paleozoic or early Mesozoic. In the southern Tuscarora Mountains area, the Ordovician and Silurian siliceous rocks deformed in the Antler Orogeny were deformed by later, possibly Mesozoic, folding and thrusting. Most of the minor folding visible in the allochthon is in the cheret, but proportionally more of the strain was taken up in the shale and argillite, both poorly exposed but predominant rock types. Most minor folds, concentric in form, plunge at small angles to the north-northeast and south-southwest with steeply dipping or vertical axial planes. The b-fabric axis, parallel to these folds, is identical apparently to the B-kinematic axis. The horizontal component of tectonic shortening of the allochthon, N. 70?-75? W. both in the Battle Mountain area and in the southern Tuscarora Mountains area, is therefore consistent with an eastward direction of movement of the allochthon. Folds with west- northwest trends locally present in the allochthon, may have formed in the direction of tectonic transport. In the southern Tuscarora Mountains, local strain in and below the allochthon was different from the prevailing strain in the allochthon, and tectonic shortening was locally at large angles to the accepted direction of movement of the allochthon.

Meteorite Impact Structures as Outcrop-Scale Analogues for Mountain Building Events: Weaubleau and Decaturville, MO

NASA Astrophysics Data System (ADS)

Wu, S.; McKay, M.; Evans, K. R.

2017-12-01

Understanding the architecture of mountain belts is limited because studies are typically confined to surficial exposures with lesser amounts of subsurface data and active margins are prone to successive tectonism that obscures the rock record. In west-central Missouri, two Paleozoic meteorite impacts are exposed that contain a range of outcrop-scale structures. While the strain rate in a meteorite impact is an order of magnitude greater than that in orogeny-scale structures, the morphology and spatial relationships in these impact structures may provide insight into larger tectonic features. The entire crater could not be compared to an orogenic event because the amount of strain diffuses as distance increases from the impactor during an impacting event. The center of an impact crater could not be compared to an orogenic event because it has become too deformed. However, the crater rim and the immediate surrounding area could be used as a comparison because it has undergone the right amount of deformation to have recognizable structures. High-detail mapping and structural analyses of road cut exposures near Decaturville, MO reveals thrust fault sequences contain 1-2 m thick mixed carbonate and clastic sheets that include rollover anticlines, structural orphans, and lateral ramp features. Thrust faults dip away from the impact structure and represent gravitational collapse of the central uplift seconds after collision. Thrust sheet thickness, thrust fault spacing, ramp/flat morphology, and shortening of within these structures will be presented and assessed as an analogue for map-scale features in the Southern Appalachian fold and thrust belt. Because temperature controls rock mechanic properties, a thermal model based on thermochronology and thermobarometry for the section will also be presented and discussed in the context of orogenic thermomechanics.

Origin and tectonic significance of a Mesozoic multi-layer over-thrust system within the Yangtze Block (South China)

NASA Astrophysics Data System (ADS)

Yan, Dan-Ping; Zhou, Mei-Fu; Song, Hong-Lin; Wang, Xin-Wen; Malpas, John

2003-01-01

In the Yangtze Block (South China), a well-developed Mesozoic thrust system extends through the Xuefeng and Wuling mountains in the southeast to the Sichuan basin in the northwest. The system comprises both thin- and thick-skinned thrust units separated by a boundary detachment fault, the Dayin fault. To the northwest, the thin-skinned belt is characterized by either chevron anticlines and box synclines to the northwest or chevron synclines to the southeast. The former structural style displays narrow exposures for the cores of anticlines and wider exposures for the cores of synclines. Thrust detachments occur along Silurian (Fs) and Lower Cambrian (Fc) strata and are dominantly associated with the anticlines. To the southeast, this style of deformation passes gradually into one characterized by chevron synclines with associated principal detachment faults along Silurian (Fs), Cambrian (Fc) and Lower Sinian (Fz) strata. There are, however, numerous secondary back thrusts. Therefore, the thin-skinned belt is like the Valley and Ridge Province of the North American Applachian Mountains. The thick-skinned belt structurally overlies the thin-skinned belt and is characterized by a number of klippen including the Xuefeng and Wuling nappes. It is thus comparable to the Blue Ridge Province of Appalachia. The structural pattern of this thrust system in South China can be explained by a model involving detachment faulting along various stratigraphic layers at different stages of its evolution. The system was developed through a northwest stepwise progression of deformation with the earliest delamination along Lower Sinian strata (Fz). Analyses of balanced geological cross-sections yield about 18.1-21% (total 88 km) shortening for the thin-skinned unit and at least this amount of shortening for the thick-skinned unit. The compressional deformation from southeast to northwest during Late Jurassic to Cretaceous time occurred after the westward progressive collision of the Yangtze Block with the North China Block and suggests that the orogenic event was intracontinental in nature.

Role of Neogene Exhumation and Sedimentation on Critical-Wedge Kinematics in the Zagros Orogenic Belt, Northeastern Iraq, Kurdistan

NASA Astrophysics Data System (ADS)

Koshnaw, R. I.; Horton, B. K.; Stockli, D. F.; Barber, D. E.; Tamar-Agha, M. Y.; Kendall, J. J.

2014-12-01

The Zagros orogenic belt and foreland basin formed during the Cenozoic Arabia-Eurasia collision, but the precise histories of shortening and sediment accumulation remain ambiguous, especially at the NW extent of the fold-thrust belt in Iraqi Kurdistan. This region is characterized by well-preserved successions of Cenozoic clastic foreland-basin fill and deformed Paleozoic-Mesozoic hinterland bedrock. The study area provides an excellent opportunity to investigate the linkage between orogenic wedge behavior and surface processes of erosion and deposition. The aim of this research is to test whether the Zagros orogenic wedge advanced steadily under critical to supercritical wedge conditions involving in-sequence thrusting with minimal erosion or propagated intermittently under subcritical condition involving out-of-sequence deformation with intense erosion. These endmember modes of mountain building can be assessed by integrating geo/thermochronologic and basin analyses techniques, including apatite (U-Th)/He thermochronology, detrital zircon U-Pb geochronology, stratigraphic synthesis, and seismic interpretations. Preliminary apatite (U-Th)/He data indicate activation of the Main Zagros Fault (MZF) at ~10 Ma with frontal thrusts initiating at ~8 Ma. However, thermochronometric results from the intervening Mountain Front Flexure (MFF), located between the MZF and the frontal thrusts, suggest rapid exhumation at ~6 Ma. These results suggest that the MFF, represented by the thrust-cored Qaradagh anticline, represents a major episode of out-of-sequence deformation. Detrital zircon U-Pb analyses from the Neogene foreland-basin deposits show continuous sediment derivation from sources to the NNE in Iraq and western Iran, suggesting that out-of-sequence thrusting did not significantly alter sedimentary provenance. Rather, intense hinterland erosion and recycling of older foreland-basin fill dominated sediment delivery to the basin. The irregular distribution of thermochronologic ages, hinterland growth, extensive erosion, and recycled sediment in the Neogene foreland basin imply that the Zagros orogenic wedge in the Iraqi Kurdistan region largely developed under subcritical wedge conditions.

40Ar/39Ar dates from alkaline intrusions of the northern Crazy Mountains, south-central Montana

NASA Astrophysics Data System (ADS)

Harlan, S. S.

2005-05-01

The Crazy Mountains basin of south-central Montana is a complex foreland basin that formed during the interaction of thin-skinned, decollement-style folds of the Montana thrust belt and the basement-involved folds and thrust faults of the Rocky Mountain foreland province. Near the depositional center of the basin, synorogenic strata of the Paleocene Fort Union Formation have been intruded and locally thermally metamorphosed by strongly alkaline to subalkaline Tertiary intrusive rocks. The subalkaline rocks are found mostly in the southern Crazy Mountains and form stocks (Big Timber stock, Loco Mountain stock), radiating dikes and sills. With the exception of the Ibex Mountain sill (?), the alkaline rocks are restricted to the northern Crazy Mountains. New 40Ar/39Ar dates are reported from the strongly alkaline rocks, including the Comb Creek stock and dike swarm, the Ibex Mountain sill(?), and sills from the Robinson anticline intrusive complex. The alkaline rocks of the Robinson anticline intrusive complex are exposed in the easternmost folds of the Cordilleran fold and thrust belt, but despite their arcuate and apparently folded map geometry they have been shown to post-date folding. Hornblende from a trachyte sill in the Robinson anticline intrusive complex yielded a relatively simple age spectrum with a weighted mean of 50.61 ± 0.14 Ma (2σ), which probably records the age of sill emplacement. Nepheline syenite and mafic nepheline syenites of the Comb Creek stock and a dike from its radial dike swarm, two sills from the Robinson antlicline intrusive complex, and the Ibex Mountains sill(?) gave biotite plateau dates ranging from 50.03 to 50.22 Ma, with 2σ errors of ± 0.11 to 0.19 Ma. Because these dates are from fairly small, hypabyssal intrusions, they must have cooled quickly and thus these dates closely approximate the emplacement age of the intrusions. These data indicate that the strongly alkaline intrusions were emplaced during a fairly restricted interval of time at about 50.1 Ma. The dates from the alkaline rocks are somewhat older than dates from the subalkaline Big Timber stock in the southern Crazy Mountains, which gave biotite 40Ar/39Ar dates of about 49.3 Ma (du Bray and Harlan, 1996). However, because these dates represent cooling through closure temperatures of about 350° C, they are minimum estimates for the age of the stock. The limited span of 40Ar/39Ar dates between the alkaline and subalkaline rocks of the Crazy Mountains intrusions (i.e., 50.6 to 49.2 Ma) indicates that the magmas represented by these different geochemical groups were closely associated in both time and space, with emplacement occurring in as little as 1.5 Ma. On a regional scale, the 49-51 Ma age is similar to that of most of the igneous centers of the Central Montana alkalic province and is coeval with the peak of widespread volcanism in the Absaroka-Gallatin volcanic field immediately to the south of the Crazy Mountains Basin.

Uniquely Acquired Vintage Seismic Reflection Data Reveal the Stratigraphic and Tectonic History of the Montana Disturbed Belt, USA

NASA Astrophysics Data System (ADS)

Speece, M. A.; Link, C. A.; Stickney, M.

2011-12-01

In 1983 and 1984 Techco of Denver, Colorado, acquired approximately 302 linear kilometers of two-dimensional (2D) seismic reflection data in Flathead and Lake Counties, Montana, USA, as part of an initiative to identify potential drilling targets beneath the Swan and Whitefish Mountain Ranges and adjacent basins of northwestern Montana. These seismic lines were collected in the Montana Disturbed Belt (MDB) or Montana thrust belt along the western edge of Glacier National Park in mountainous terrain with complicated subsurface structures including thrust faults and folds. These structures formed during the Laramide Orogeny as sedimentary rocks of the Precambrian Belt Supergroup were thrust eastward. Later, during the Cenozoic, high-angle normal faults produced prominent west-facing mountain scarps of the Mission, Swan and Whitefish mountains. The 1983 data set consisted of two profiles of 24-fold (96-channels) Vibroseis data and four profiles of 24-fold (96-channels) helicopter-assisted dynamite data. The dynamite data were collected using the Poulter Method in which explosives were placed on poles and air shots were recorded. The 1983 dynamite profiles extend from southwest to northeast across the Whitefish Mountain Range to the edge of Glacier National Park and the Vibroseis data were collected along nearby roadways. The 1984 data set consists of four profiles of 30-fold (120-channels) helicopter-assisted dynamite data that were also collected using the Poulter Method. The 1984 profiles cross the Swan Mountain Range between Flathead Lake and Glacier National Park. All of these data sets were recently donated to Montana Tech and subsequently recovered from nine-track tape. Conventionally processed seismic stacked sections from the 1980s of these data show evidence of a basement decollement that separates relatively undeformed basement from overlying structures of the MDB. Unfortunately, these data sets have not been processed using modern seismic processing techniques including linear noise suppression of the air wave and ground roll, refraction statics, and prestack migration. Reprocessing of these data using state-of-the-art seismic reflection processing techniques will provide a detailed picture of the stratigraphy and tectonic framework for this region. Moreover, extended correlations of the Vibroseis records to Moho depths might reveal new insights on crustal thickness and provide a framework for understanding crustal thickening during the Laramide Orogeny as well as later Cenozoic extension.

Plateau growth around the Changma Basin in NE Tibet

NASA Astrophysics Data System (ADS)

Vernon, Rowan; Cunningham, Dickson; Zhang, Jin; England, Richard

2014-05-01

The Qilian Mountains form one of the most actively uplifting regions of the northeastern Tibetan Plateau and provide an opportunity to study the ongoing, intermediate stages of plateau growth. The crust of the Qilian Mountains consists of an orogenic collage of mid-Proterozoic to mid-Palaeozoic island arc terranes accreted to the North China Craton during the Palaeozoic. NE-directed compression related to the Indo-Asian collision began in the Early Neogene, uplifting fold-thrust mountain ranges which splay south-eastwards from the sinistral northeast-trending Altyn Tagh Fault (ATF). In this study, we investigate the post-Oligocene tectonic evolution of the northern margin of the Tibetan Plateau around the Changma Basin, at the very northeast corner of the Plateau, where the ATF forms a triple junction with the frontal Qilian Shan thrust. Our research involves synthesis of previous geological and geophysical data, remote sensing analysis and field mapping of structures along key transects. The Changma Basin is a relatively low intra-montane basin in the northeast Tibetan Plateau that is receiving alluvial infill from surrounding ranges, but is also being drained by the Su Le River, one of the largest river systems in the northeast Tibetan Plateau. The basin is also internally deforming and inverting along fault and fold zones, as well as being overthrust along some of its margins. Where older basement trends are parallel to neotectonic faults, some reactivation is inferred and locally documented through field observations. Otherwise, the post-Oligocene thrust and oblique-slip faults which are responsible for uplifting various basement blocks and inverting the Changma Basin appear discordant to nearby basement trends. Range-bounding thrust faults with the greatest along-strike continuity and relief generation are assumed to have the largest displacements, whereas other intra-range thrusts that bound uplifted limestone blocks are assumed to have lower amounts of displacement. Structural transects reveal a lack of intra-range reactivation of inherited structures or fabrics, concentrating uplift on the lithologically-controlled intra-range thrust faults and the major range-bounding thrust and oblique-slip faults. Northeast of the Changma Basin, in the Qilian Shan foreland, an east-trending belt of low folds and faulted ridges along the ATF marks the structural continuation of the Yumen Shan range. We find that uplift and growth of northeastern Tibet is complex with local variations in structural vergence, degree of strain partitioning, fault reactivation and basin inversion. This complexity reflects both the buttressing effect of the rigid Archaean basement directly to the north and the variation in the structural trends and lithologies of the Qilian basement, as well as the competition between uplift and erosion in the region.

Active folding and thrusting in North Africa: A framework for a seismotectonic model of the Atlas Mountains

NASA Astrophysics Data System (ADS)

Meghraoui, Mustapha; Maouche, Said; Timoulali, Youssef; Bouhadad, Youcef; Bouaziz, Samir

2013-04-01

Large earthquakes in the Atlas Mountains of North Africa are often generated on thrust or reverse faults. For inland faults, surface ruptures and long-term active tectonics appear as a thrust escarpment and fold-related faulting visible in the field and using remote sensing images, or measured using space-borne geodesy (GPS or INSAR). For coastal faults, major uplifts of late Quaternary marine terraces and folding with steplike morphology are exposed indicating the incremental development of coastal active deformation. We have investigated the similarities and differences between different active fault-related folding along the Africa - Eurasia convergent plate boundary. These active structures are seismogenic and the striking case studies are the 1960 Agadir (Mw 5.9), the 1954 Orleansville (Mw 6.7), the 1980 El Asnam (Mw 7.3), the 1992 Gafsa (Mw 5.3), the 1999 Ain Temouchent (Mw 6.0), and the 2003 Zemmouri (Mw 6.8) earthquakes. From paleoseismic investigations the El Asnam active fold shows 0.6 to 1.0 mm/yr uplift rate. West of Algiers on the Sahel anticline, the levelling of uplifted successive coastal benches and notches document the incremental folding uplift with ~ 0.84 - 1.2 mm/yr uplift rate in the last 120-140 ka. The relatively fast folding growth during late Pleistocene and Holocene in the Atlas Mountains attests for the significance of earthquake activity and the importance of convergent movements between Africa and Eurasia in the Western Mediterranean. This work is prepared in the framework of the UNESCO (SIDA) - IGCP Project 601 "Seismotectonics and Seismic Hazards in Africa".

Structural analysis and tectonic evolution of the eastern Binalud Mountains, NE Iran

NASA Astrophysics Data System (ADS)

Sheikholeslami, M. R.; Kouhpeyma, M.

2012-10-01

The Binalud Mountains are situated in the south of the Kopeh Dagh as a transitional zone between the Alborz and Central Iran zones. The Palaeotethys suture of the north Iran is located in this area. The Binalud Mountains consists of relatively thick successions of sedimentary, metamorphic and igneous rocks. The earliest deformation, a polyphase synmetamorphic deformation which occurred entirely in ductile conditions, is distinguished in the metamorphic rocks of the eastern part. D1, D2 and D3 deformation phases are related to this deformation. The D4 deformation affected the area after a period of sedimentation and erosion. The thrust faults of the central and southern part of the eastern Binalud were classified as structures related to the D5 tectonic event. From the geodynamic point of view, in Late Palaeozoic times the studied area formed an oceanic trench generated by the subduction of the Palaeotethys oceanic lithosphere beneath the Turan Plate. In the Late Triassic, the Early Cimmerian Event resulted in a collisional type orogeny generating a transpression polyphase deformation and the metamorphism of Permian and older sediments. Following this collision, granite intrusions were emplaced in the area and caused contact metamorphism. The exhumation and erosion of the rocks deformed and metamorphosed during Early Cimmerian Event caused the formation of molassic type sediments in a Rhaetian-Lias back arc basin. The continuation of convergence between the Turan and Iran Plates caused the metamorphism of these sediments and their transformation to phyllite and meta-sandstone. During Late Mesozoic and Early Cenozoic times, the convergence between Central Iran and Turan Plates continued and a NE compression caused folding of the Cretaceous and older rocks in the Kopeh Dagh area. In the Binalud area this deformation caused the generation of several thrust fault systems with S to SW vergence, resulting in a thrusting of Palaeozoic and Mesozoic successions on each other and on the Neogene sediments at the southern border of the Binalud Mountains.

Extrusional Tectonics over Plate Corner: an Example in Northern Taiwan

NASA Astrophysics Data System (ADS)

Lu, Chia-Yu; Lee, Jian-Cheng; Li, Zhinuo; Lee, Ching-An; Yeh, Chia-Hung

2016-04-01

In northern Taiwan, contraction, transcurrent shearing, block rotation and extension are four essential tectonic deformation mechanisms involved in the progressive deformation of this arcuate collision mountain belt. The neotectonic evolution of the Taiwan mountain belt is mainly controlled not only by the oblique convergence between the Eurasian plate and the Philippine Sea plate but also the corner shape of the plate boundary. Based on field observations and analyses, and taking geophysical data (mostly GPS) and experimental modelling into account, we interpret the curved belt of northern Taiwan as a result of of contractional deformation (with compression, thrust-sheet stacking & folding, back thrust duplex & back folding) that induced vertical extrusion, combined with increasing transcurrent & rotational deformation (with transcurrent faulting, bookshelf-type strike-slip faulting and block rotation) that induced transcurrent/rotational extrusion and extension deformation which in turn induced extensional extrusion. As a consequence, a special type of extrusional folds was formed in association with contractional, transcurrent & rotational and extensional extrusions subsequently. The extrusional tectonics in northern Taiwan reflect a single, albeit complicated, regional pattern of deformation. The crescent-shaped mountain belt of Northeastern Taiwan develops in response to oblique indentation by an asymmetric wedge indenter, retreat of Ryukyu trench and opening of the Okinawa trough.

Extrusional Tectonics at Plate Corner: an Example in Northern Taiwan

NASA Astrophysics Data System (ADS)

Lu, C. Y.; Lee, J. C.; Li, Z.; Yeh, C. H.; Lee, C. A.

2015-12-01

In northern Taiwan, contraction, transcurrent shearing, block rotation and extension are four essential tectonic deformation mechanisms involved in the progressive deformation of this arcuate collision mountain belt. The neotectonic evolution of the Taiwan mountain belt is mainly controlled not only by the oblique convergence between the Eurasian plate and the Philippine Sea plate but also the corner shape of the plate boundary. Based on field observations and analyses, and taking geophysical data (mostly GPS) and experimental modelling into account, we interpret the curved belt of northern Taiwan as a result of of contractional deformation (with compression, thrust-sheet stacking & folding, back thrust duplex & back folding) that induced vertical extrusion, combined with increasing transcurrent & rotational deformation (with transcurrent faulting, bookshelf-type strike-slip faulting and block rotation) that induced transcurrent/rotational extrusion and extension deformation which in turn induced extensional extrusion. As a consequence, a special type of extrusional folds was formed in association with contractional, transcurrent & rotational and extensional extrusions subsequently. The extrusional tectonics in northern Taiwan reflect a single, albeit complicated, regional pattern of deformation. The crescent-shaped mountain belt of Northeastern Taiwan develops in response to oblique indentation by an asymmetric wedge indenter and opening of the Okinawa trough at plate corner.

Cordilleran front range structural features in northwest Montana interpreted from vintage seismic reflection data

NASA Astrophysics Data System (ADS)

Porter, Mason C.; Rutherford, Bradley S.; Speece, Marvin A.; Mosolf, Jesse G.

2016-04-01

Industry seismic reflection data spanning the Rocky Mountain Cordillera front ranges of northwest Montana were reprocessed and interpreted in this study. Five seismic profiles represent 160 km of deep reflection data collected in 1983 that span the eastern Purcell anticlinorium, Rocky Mountain Trench (RMT), Rocky Mountain Basal Décollement (RMBD), and Lewis thrust. The data were reprocessed using modern techniques including refraction statics, pre-stack time migration (PSTM), and pre- and post-stack depth migration. Results indicate the RMBD is 8-13 km below the Earth's surface and dip 3-10° west. Evidence for the autochthonous Mesoproterozoic Belt and basal Cambrian rocks beneath the RMBD is present in all of the profiles and appears to extend east of the RMT. The Lewis thrust was identified in the seismic profiles and appears to sole into the RMBD east of the RMT. The RMT fault system has a dip displacement of 3-4 km and forms a half graben filled with 1 km of unconsolidated Tertiary sedimentary deposits. The RMT and adjacent Flathead fault systems are interpreted to be structurally linked and may represent a synthetic, en echelon fault system.

Progressive deformation and superposed fabrics related to Cretaceous crustal underthrusting in western Arizona, U.S.A.

USGS Publications Warehouse

Laubach, S.E.; Reynolds, S.J.; Spencer, J.E.; Marshak, S.

1989-01-01

In the Maria fold and thrust belt, a newly recognized E-trending Cretaceous orogenic belt in the southwestern United States, ductile thrusts, large folds and superposed cleavages record discordant emplacement of crystalline thrust sheets across previously tilted sections of crust. Style of deformation and direction of thrusting are in sharp contrast to those of the foreland fold-thrust belt in adjacent segments of the Cordillera. The net effect of polyphase deformation in the Maria belt was underthrusting of Paleozoic and Mesozoic metasedimentary rocks under the Proterozoic crystalline basement of North America. The structure of the Maria belt is illustrated by the Granite Wash Mountains in west-central Arizona, where at least four non-coaxial deformation events (D1-D4) occurred during the Cretaceous. SSE-facing D1 folds are associated with S-directed thrusts and a low-grade slaty cleavage. D1 structures are truncated by the gently-dipping Hercules thrust zone (D2), a regional SW-vergent shear zone that placed Proterozoic and Jurassic crystalline rocks over upturned Paleozoic and Mesozoic supracrustal rocks. Exposures across the footwall margin of the Hercules thrust zone show the progressive development of folds, cleavage and metamorphism related to thrusting. D3 and D4 structures include open folds and spaced cleavages that refold or transect D1 and D2 folds. The D2 Hercules thrust zone and a D3 shear zone are discordantly crosscut by late Cretaceous plutons. ?? 1989.

Regional metamorphism in the Condrey Mountain Quadrangle, north-central Klamath Mountains, California

USGS Publications Warehouse

Hotz, Preston Enslow

1979-01-01

A subcircular area of about 650 km 2 in northern California and southwestern Oregon is occupied by rocks of the greenschist metamorphic facies called the Condrey Mountain Schist. This greenschist terrane is bordered on the east and west by rocks belonging to the amphibolite metamorphic facies that structurally overlie and are thrust over the Condrey Mountain Schist. The amphibolite facies is succeeded upward by metavolcanic and metasedimentary rocks belonging to the greenschist metamorphic facies. The Condrey Mountain Schist is composed predominantly of quartz-muscovite schist and lesser amounts of actinolite-chlorite schist formed by the metamorphism of graywacke and spilitic volcanic rocks that may have belonged to the Galice Formation of Late Jurassic age. Potassium-argon age determinations of 141?4 m.y. and 155?5 m.y. obtained on these metamorphic rocks seem to be incompatible with the Late Jurassic age usually assigned the Galice. The rocks that border the amphibolite facies are part of an extensive terrane of metavolcanic and metasedimentary rocks belonging to the western Paleozoic and Triassic belt. The metavolcanic rocks include some unmetamorphosed spilite but are mostly of the greenschist metamorphic facies composed of oligoclase (An15-20) and actinolite with subordinate amounts of chlorite and clinozoisiteepidote. The interbedded sedimentary rocks are predominantly argillite and slaty argillite, less commonly siliceous argillite and chert, and a few lenticular beds of marble. On the south, high-angle faults and a tabular granitic pluton separate the greenschist metavolcanic terrane from the amphibolite facies rocks; on the east, nonfoliated amphibolite is succeeded upward, apparently conformably, by metasedimentary rocks belonging to the greenschist metavolcanic terrane. In the southern part of Condrey Mountain quadrangle, an outlier of a thrust plate composed of the Stuart Fork Formation overlies the metavolcanic and metasedimentary rocks. The Stuart Fork in this region is composed of siliceous phyllite and phyllitic quartzite and is believed to be the metamorphosed equivalent of rocks over which it is thrust. In the Yreka-Fort Jones area, potassium-argon determinations on mica from the blueschist facies in the Stuart Fork gave ages of approximately 220 m.y. (Late Triassic) for the age of metamorphism. Rocks of the amphibolite facies structurally overlie the Condrey Mountain Schist along a moderate to steeply dipping thrust fault. The amphibolite terrane is composed of amphibolite and metasedimentary rocks in approximately equal amounts accompanied by many bodies of serpentinite and a number of gabbro and dioritic plutons. Most of the amphibolite is foliated, but some is nonfoliated; the nonfoliated amphibolite has an amphibolite mineralogy and commonly a relict volcanic rock texture. The nonfoliated amphibolite occurs on the southern and eastern borders of the amphibolite terrane between the areas offoliated amphibolite and the overly ing metavolcanic and metasedimentary rocks. Hornblende and plagioclase (An30-35) are the characteristic minerals, indicating that the rocks are of the almandine-amphibolite metamorphic facies. The metasedimentary rocks interbedded with the amphibolites include siliceous schist and phyllite, minor quartzite, and subordinate amounts of marble. Potassium-argon age dates obtained on hornblende from foliated amphibolite yield ages of 146?4 and 148? 4 m.y., suggesting a Late Jurassic metamorphic episode. Mafic and ultramafic rocks are widespread in the amphibolite terrane but are almost entirely absent from the area of greenschist facies metavolcanic and metasedimentary rocks. The ultramafic rocks, predominantly serpentinite, occur as a few large bodies and many small tabular concordant bodies interleaved with the foliated rocks. The ultramafic rocks include harzburgite and d1lIlite and their serpentinized equivalents. In the Condrey Mountain quadrangle, probably more t

Multistory duplexes with forward dipping roofs, north central Brooks Range, Alaska

USGS Publications Warehouse

Wallace, W.K.; Moore, Thomas E.; Plafker, G.

1997-01-01

The Endicott Mountains allochthon has been thrust far northward over the North Slope parautochthon in the northern Brooks Range. Progressively younger units are exposed northward within the allochthon. To the south, the incompetent Hunt Fork Shale has thickened internally by asymmetric folds and thrust faults. Northward, the competent Kanayut Conglomerate forms a duplex between a floor thrust in Hunt Fork and a roof thrust in the Kayak Shale. To the north, the competent Lisburne Group forms a duplex between a floor thrust in Kayak and a roof thrust in the Siksikpuk Formation. Both duplexes formed from north vergent detachment folds whose steep limbs were later truncated by south dipping thrust faults that only locally breach immediately overlying roof thrusts. Within the parautochthon, the Kayak, Lisburne, and Siksikpuk-equivalent Echooka Formation form a duplex identical to that in the allochthon. This duplex is succeeded abruptly northward by detachment folds in Lisburne. These folds are parasitic to an anticlinorium interpreted to reflect a fault-bend folded horse in North Slope "basement," with a roof thrust in Kayak and a floor thrust at depth. These structures constitute two northward tapered, internally deformed wedges that are juxtaposed at the base of the allochthon. Within each wedge, competent units have been shortened independently between detachments, located mainly in incompetent units. The basal detachment of each wedge cuts upsection forward (northward) to define a wedge geometry within which units dip regionally forward. These dips reflect forward decrease in internal structural thickening by forward vergent folds and hindward dipping thrust faults. Copyright 1997 by the American Geophysical Union.

New data for Late Pleistocene Pinedale alpine glaciation from southwestern Colorado

USGS Publications Warehouse

Benson, L.; Madole, R.; Landis, G.; Gosse, J.

2005-01-01

New cosmogenic surface-exposure ages of moraine-crest boulders from southwestern Colorado are compared with published surface-exposure ages of boulders from moraine complexes in north-central Colorado and in west-central (Fremont Lake basin) Wyoming. 10Be data sets from the three areas were scaled to a single 10Be production rate of 5.4 at/g/yr at sea level and high latitude (SLHL), which represents the average 10Be production rate for two high-altitude, mid-latitude sites in the western United States (US) and Austria. Multiple nuclide ages on single boulders indicate that this 10Be production rate yields ages comparable to those calculated with a commonly used 36Cl production scheme. The average age and age range of moraine-crest boulders on terminal moraines at the southwestern Colorado and Wyoming sites are similar, indicating a retreat from their positions ???16.8 36Cl ka (Cosmogenic ages in this paper are labeled 10Be or 36Cl ka or just ka when both 10Be or 36Cl ages are being discussed; radiocarbon ages are labeled 14C ka, calibrated radiocarbon are labeled cal ka, and calendar ages are labeled calendar ka. Errors (??1??) associated with ages are shown in tables. Radiocarbon ages were calibrated using the data of Hughen et al. (Science 303 (2004) 202). This suggests a near-synchronous retreat of Pinedale glaciers across a 470-km latitudinal range in the Middle and Southern Rocky Mountains. Hypothetical corrections for snow shielding and rock-surface erosion shifts the time of retreat to between 17.2 and 17.5 10Be ka at Pinedale, Wyoming, and between 16.3 and 17.3 36Cl ka at Hogback Mountain, Colorado. ?? 2004 Elsevier Ltd. All rights reserved.

Neogene Tectonics of Part of the Junction of Cyprus and Hellenic Arcs in the Eastern Mediterranean Sea

NASA Astrophysics Data System (ADS)

Küçük, H. M.; Dondurur, D.; ćifçi, G.; Gürçay, S.; Hall, J.; Yaltırak, C.; Aksu, A. E.

2012-04-01

The junction between the Hellenic and Cyprus Arcs is one of the tectonically most active regions of the eastern Mediterranean. This junction developed in association with convergence between the African and Eurasian Plates, and the re-organization of the smaller Aegean-Anatolian and Arabian Microplates. Recent studies have shown that the predominant Miocene deformation process in the eastern Mediterranean is compressional tectonism. However, many studies have also shown that the strain is partitioned in the Pliocene-Quaternary and the area displays regions dominated by compression, strike slip and extensional tectonism. The junction between the Hellenic and Cyprus Arcs exhibits complex morphological features including submarine mountains, rises, ridges and trenches. Approximately 600 km of high resolution 72-channel seismic profiles were collected from the junction of Cyprus and Hellenic Arcs using a 450 m long 6.25 m hydrophone spacing streamer and a seven gun array with a 200 cubic inch total volume. This project was part of the joint scientific venture between Dokuz Eylül University (Turkey) and Memorial University of Newfoundland (Canada), and was funded by TÜBITAK and NSERC. The study area includes the southwestern Antalya Basin and the Anaxagoras Mountain of the larger Anaximander Mountains. The multichannel data were processed both at Dokuz Eylül and Memorial University of Newfoundland, using the Landmark Graphics ProMAX software, with automatic gain control, short-gap deconvolution, velocity analysis, normal move-out correction, stack, filter (typically 50-200 Hz bandpass), f-k time migration, and adjacent trace sum. Despite the fact that the source volume was modest, reflections are imaged to 2-3 s two-way time below seabed, even in 2 km water depth. The processed seismic reflection profiles show that there are three distinct sedimentary units, separated by two prominent markers: the M-reflector separates the Pliocene-Quaternary from the underlying Messinian evaporite successions, and the N-reflector separates the Messinian evaporite successions from the pre-Messinian Miocene sediments. Interpretation of the data clearly shows that the Miocene and Pliocene-Quaternary tectonic frameworks of the Anaxagoras Mountain are dominated by thrust faults. These major faults in turn, control all of the sedimentary structures observed over the submarine mountain. These thrusts display E-W trending map traces and show southerly vergence. The seismic profiles across the southwestern margin of the Antalya Basin, immediately north of the Anaxagoras Mountain show the presence of numerous upright anticlines and their intervening synclines. These structures are interpreted as salt-cored anticlines. Although mud volcanoes and diapiric structures have also been observed in the area, the normal-move-out velocities suggest that these structures are indeed cored by evaporites. The western margin of the Anaxagoras Mountain is delineated by a profound lineation which separates it from the Anaximander Mountains in the west. In the seismic reflection profiles, this lineation appears to be controlled by NE-SW-trending and mainly west-verging thrusts. The tip points of these thrusts lie at the depositional surface, and their trajectories can be traced well below 4-5 seconds. It is speculated that this prominent and somewhat arcuate boundary defines a crustal scale structure that links the Anaximander Mountains to the Antalya Basin. If so, it might have a sinistral strike slip component, possibly associated with the clockwise rotation of the Anaxagoras Mountain. The acoustic basement is located at approximately 5-6 s in the seismic reflection profiles from the Antalya Basin, and is interpreted to include Miocene-Oligocene sediments. A short seismic profile from the eastern side of Finike basin shows that Pliocene-Quaternary thickness of Finike Basin is more than in the Antalya Basin. The fact that no unequivocal evaporite successions are observed in the Finike Basin is puzzling and requires that the Finike Basin either remained above the depositional surface during the Messinian or was isolated from the eastern Mediterranean Sea.

Control on frontal thrust progression by the mechanically weak Gondwana horizon in the Darjeeling-Sikkim Himalaya

NASA Astrophysics Data System (ADS)

Ghosh, Subhajit; Bose, Santanu; Mandal, Nibir; Das, Animesh

2018-03-01

This study integrates field evidence with laboratory experiments to show the mechanical effects of a lithologically contrasting stratigraphic sequence on the development of frontal thrusts: Main Boundary Thrust (MBT) and Daling Thrust (DT) in the Darjeeling-Sikkim Himalaya (DSH). We carried out field investigations mainly along two river sections in the DSH: Tista-Kalijhora and Mahanadi, covering an orogen-parallel stretch of 20 km. Our field observations suggest that the coal-shale dominated Gondwana sequence (sandwiched between the Daling Group in the north and Siwaliks in the south) has acted as a mechanically weak horizon to localize the MBT and DT. We simulated a similar mechanical setting in scaled model experiments to validate our field interpretation. In experiments, such a weak horizon at a shallow depth perturbs the sequential thrust progression, and causes a thrust to localize in the vicinity of the weak zone, splaying from the basal detachment. We correlate this weak-zone-controlled thrust with the DT, which accommodates a large shortening prior to activation of the weak zone as a new detachment with ongoing horizontal shortening. The entire shortening in the model is then transferred to this shallow detachment to produce a new sequence of thrust splays. Extrapolating this model result to the natural prototype, we show that the mechanically weak Gondwana Sequence has caused localization of the DT and MBT in the mountain front of DSH.

Ice Surface Morphology and Flow on Malaspina Glacier, Alaska: Implications for Regional Tectonics in the Saint Elias Orogen

NASA Technical Reports Server (NTRS)

Cotton, Michelle M.; Bruhn, Ronald L.; Sauber, Jeanne; Burgess, Evan; Forster, Richard R.

2014-01-01

The Saint Elias Mountains in southern Alaska are located at a structural syntaxis where the coastal thrust and fold belt of the Fairweather plate boundary intersects thrust faults and folds generated by collision of the Yakutat Terrane. The axial trace of this syntaxis extends southeastward out of the Saint Elias Mountains and beneath Malaspina Glacier where it is hidden from view and cannot be mapped using conventional methods. Here we examine the surface morphology and flow patterns of Malaspina Glacier to infer characteristics of the bedrock topography and organization of the syntaxis. Faults and folds beneath the eastern part of the glacier trend northwest and reflect dextral transpression near the terminus of the Fairweather fault system. Those beneath the western part of the glacier trend northeast and accommodate folding and thrust faulting during collision and accretion of the Yakutat Terrane. Mapping the location and geometry of the structural syntaxis provides important constraints on spatial variations in seismicity, fault kinematics, and crustal shortening beneath Malaspina Glacier, as well as the position of the collisional deformation front within the Yakutat Terrane. We also speculate that the geometrical complexity of intersecting faults within the syntaxis formed a barrier to rupture propagation during two regional Mw 8.1earthquakes in September 1899.

Development of Archean crust in the Wind River Mountains, Wyoming

NASA Technical Reports Server (NTRS)

Frost, C. D.; Koesterer, M. E.; Koesterer, M. E.; Koesterer, M. E.; Koesterer, M. E.

1986-01-01

The Wind River Mountains are a NW-SE trending range composed almost entirely of high-grade Archean gneiss and granites which were thrust to the west over Phanerozoic sediments during the Laramide orogeny. Late Archean granites make up over 50% of the exposed crust and dominates the southern half of the range, while older orthogneisses and magnatites form most of the northen half of the range. Locally these gneisses contain enclaves of supracrustal rocks, which appear to be the oldest preserved rocks in the range. Detailed work in the Medina Mountain area of the central Wind River Mountains and reconnaissance work throughout much of the northern part of the range has allowed definition of the sequence of events which marked crustal development in this area. The sequence of events are described.

Cenozoic volcanic centers in the New Mexico segment of the Pedregosa Basin: constraints on oil and gas exploration in southwestern New Mexico. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elston, W.E.

1983-01-01

Located in the southwestern corner of New Mexico, southern Hidalgo County occupies a segment of the Pedregosa sedimentary basin and is crossed by a belt of Laramide thrust faults. These factors favor accumulations of oil and gas. The present investigation has documented a constraint on probable oil and gas accumulations, the occurrence of major mid-Tertiary Valles-type ash-flow cauldrons and indications of underlying plutons. Indications of cauldrons have been found in the following ranges: in the southern Pyramid Mountains (Muir cauldron), south-central Peloncillo Mountains (Rodeo cauldron), Gaudalupe Mountains (Geronimo Trail cauldron), Sierra San Luis (San Luis cauldron), Southern Animas Mountains (Tullous,more » Animas Peak, Cowboy Rim cauldrons), Central Animas Mountains (Juniper cauldron), and Apache Hills (Apache cauldron). No indications of cauldrons or other major volcanic centers have been found in the southeastern corner of Hidalgo County, including the southern Sierra Rica, Big Hatchet Mountains, Alamo Hueco Mountains, and Dog Mountains. These cauldron-free areas offer the most favorable prospects for petroleum exploration.« less

An alternative hypothesis for the mid-Paleozoic Antler orogeny in Nevada

USGS Publications Warehouse

Ketner, Keith B.

2012-01-01

A great volume of Mississippian orogenic deposits supports the concept of a mid-Paleozoic orogeny in Nevada, and the existence and timing of that event are not questioned here. The nature of the orogeny is problematic, however, and new ideas are called for. The cause of the Antler orogeny, long ascribed to plate convergence, is here attributed to left-lateral north-south strike-slip faulting in northwestern Nevada. The stratigraphic evidence originally provided in support of an associated regional thrust fault, the Roberts Mountains thrust, is now known to be invalid, and abundant, detailed map evidence testifies to post-Antler ages of virtually all large folds and thrust faults in the region. The Antler orogeny was not characterized by obduction of the Roberts Mountains allochthon; rocks composing the "allochthon" essentially were deposited in situ. Instead, the orogeny was characterized by appearance of an elongate north-northeast-trending uplift through central Nevada and by two parallel flanking depressions. The eastern depression was the Antler foreland trough, into which sediments flowed from both east and west in the Mississippian. The western depression was the Antler hinterland trough into which sediments also flowed from both east and west during the Mississippian. West of the hinterland trough, across a left-lateral strike-slip fault, an exotic landmass originally attached to the northwestern part of the North American continent was moved southward 1700 km along a strike-slip fault. An array of isolated blocks of shelf carbonate rocks, long thought to be autochthonous exposures in windows of the Roberts Mountains allochthon, is proposed here as an array of gravity-driven slide blocks dislodged from the shelf, probably initiated by the Late Devonian Alamo impact event.

Style of Cenozoic extensional deformation in the central Beaverhead Mountains, Idaho-Montana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kellogg, K.S.

1993-04-01

Cenozoic extension in the upper Medicine Lodge Creek area in the Beaverhead Mountains was accommodated along numerous low- to high-angle, west-facing normal faults. These faults have repeated moderately east-dipping (by 20--40[degree]) Tertiary rocks that are as old as the Eocene Medicine Lodge Volcanics and that include conformably overlying Miocene and Oligocene conglomerate, tuffaceous sandstone, siltstone, and limestone; a reasonable restoration of Tertiary faulting suggests that the region has extended about 20 percent. At least one normal fault soles into the Late Cretaceous Cabin thrust, one of at least four major Cordilleran thrusts in the Beaverhead Mountains and the Tendoy Mountainsmore » immediately to the east. The Cabin thrust places enigmatic quartzite (age is between Middle Proterozoic and Lower Cambrian) and Archean gneiss above Mississippian to Ordovician rocks. The formation of the north-northwest-trending upper Medicine Lodge Valley was controlled mostly by low-angle normal faults along its east side, where Eocene volcanics and overlying sedimentary rocks dip about 25[degree] eastward against Archean rocks. Faceted spurs are prominent but no scarps are visible, suggesting that last movement is pre-Holocene. Other large-displacement normal faults at higher elevations show relatively little topographic expression. The Late Proterozoic or Cambrian Beaverhead impact structure, defined by wide-spread shatter-coning, pseudotachylite formation, and localized brecciation, make interpretation of some extensive breccia zones in Archean rocks along the east side of Medicine Lodge Valley problematic. The proximity of the breccias to Tertiary normal faults makes a Tertiary age attractive, yet the breccias are older than pseudotachylite interpreted to have been produced by the impact.« less

Structural architecture of the central Brooks Range foothills, Alaska

USGS Publications Warehouse

Moore, Thomas E.; Potter, Christopher J.; O'Sullivan, Paul B.

2002-01-01

Five structural levels underlie the Brooks Range foothills, from lowest to highest: (1) autochthon, at a depth of ~9 km; (2) Endicott Mountains allochthon (EMA), thickest under the northern Brooks Range (>15 km) and wedging out northward above the autochthon; (3) higher allochthons (HA), with a composite thickness of 1.5+ km, wedging out northward at or beyond the termination of EMA; (4) Aptian-Albian Fortress Mountain Formation (FM), deposited unconformably on deformed EMA and HA and thickening northward into a >7-km-thick succession of deformed turbidites (Torok Formation); (5) gently folded Albian-Cenomanian deltaic deposits (Nanushuk Group). The dominant faulting pattern in levels 2-3 is thin-skinned thrusting and thrust-related folds formed before deposition of Cretaceous strata. These structures are cut by younger steeply south-dipping reverse faults that truncate and juxtapose structural levels 1-4 and expose progressively deeper structural levels to the south. Structural levels 4-5 are juxtaposed along a north-dipping zone of south-vergent folds and thrusts. Stratigraphic and fission-track age data suggest a kinematic model wherein the foothills belt was formed first, by thrusting of HA and EMA as deformational wedges onto the regionally south-dipping authochon at 140-120Ma. After deposition of FM and Torok during mid-Cretaceous hinterland extension and uplift, a second episode of contractional deformation at 60 Ma shortened the older allochthonous deformational wedges (EMA, HA) and overlying strata on north-vergent reverse faults. To the north, where the allochthons wedge out, shortening caused duplexing in the Torok and development of a triangle zone south of the Tuktu escarpment.

Neotectonic inversion of the Hindu Kush-Pamir mountain region

USGS Publications Warehouse

Ruleman, C.A.

2011-01-01

The Hindu Kush-Pamir region of southern Asia is one of Earth's most rapidly deforming regions and it is poorly understood. This study develops a kinematic model based on active faulting in this part of the Trans-Himalayan orogenic belt. Previous studies have described north-verging thrust faults and some strike-slip faults, reflected in the northward-convex geomorphologic and structural grain of the Pamir Mountains. However, this structural analysis suggests that contemporary tectonics are changing the style of deformation from north-verging thrusts formed during the initial contraction of the Himalayan orogeny to south-verging thrusts and a series of northwest-trending, dextral strike-slip faults in the modern transpressional regime. These northwest-trending fault zones are linked to the major right-lateral Karakoram fault, located to the east, as synthetic, conjugate shears that form a right-stepping en echelon pattern. Northwest-trending lineaments with dextral displacements extend continuously westward across the Hindu Kush-Pamir region indicating a pattern of systematic shearing of multiple blocks to the northwest as the deformation effects from Indian plate collision expands to the north-northwest. Locally, east-northeast- and northwest-trending faults display sinistral and dextral displacement, respectively, yielding conjugate shear pairs developed in a northwest-southeast compressional stress field. Geodetic measurements and focal mechanisms from historical seismicity support these surficial, tectono-morphic observations. The conjugate shear pairs may be structurally linked subsidiary faults and co-seismically slip during single large magnitude (> M7) earthquakes that occur on major south-verging thrust faults. This kinematic model provides a potential context for prehistoric, historic, and future patterns of faulting and earthquakes.

Fault dating in the Canadian Rocky Mountains: Evidence for late Cretaceous and early Eocene orogenic pulses

USGS Publications Warehouse

van der Pluijm, B.A.; Vrolijk, P.J.; Pevear, D.R.; Hall, C.M.; Solum, J.

2006-01-01

Fault rocks from the classic Rocky Mountain foreland fold-and-thrust belt in south-western Canada were dated by Ar analysis of clay grain-size fractions. Using X-ray diffraction quantification of the detrital and authigenic component of each fraction, these determinations give ages for individual faults in the area (illite age analysis). The resulting ages cluster around 72 and 52 Ma (here called the Rundle and McConnell pulses, respectively), challenging the traditional view of gradual forward progression of faulting and thrust-belt history of the area. The recognition of spatially and temporally restricted deformation episodes offers field support for theoretical models of critically stressed wedges, which result in geologically reasonable strain rates for the area. In addition to regional considerations, this study highlights the potential of direct dating of shallow fault rocks for our understanding of upper-crustal kinematics and regional tectonic analysis of ancient orogens. ?? 2006 Geological Society of America.

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCollum, L.B.; Buchanan, J.P.; McCollum, M.B.

The Antler orogeny is a textbook example of a Paleozoic mountain building and crustal shortening event in western North America. A relatively complex geologic history of the type Antler at Battle Mountain, Nevada, is interpreted as distinct thrust plates of Lower Cambrian Scott Canyon Formation, Upper Cambrian Harmony Sandstone, and Ordovician Valmy Formation, overlain unconformably by the Middle Pennsylvanian Battle Formation. Mississippian crustal deformation and emplacement of the Roberts Mountain thrust have previously been thought to characterize the Antler orogen. Detailed sedimentology studies of the Scott Canyon and Harmony, and the relationship with the overlying Battle Formation at the typemore » section of the Antler orogeny, cast doubt on the previously accepted geologic history. The Scott Canyon is an interbedded sequence of pillow basalts, Late Devonian radiolarian cherts, and mudstone debris flows with numerous limestone olistoliths, many containing undescribed archaeocyathid fauna. The contact of the Harmony with the Battle Formation appears channeled, but otherwise conformable, and the Battle has been interpreted as an alluvial fan facies. The paleoenvironmental interpretation of these sediments is that the Scott Canyon was deposited upon a Late Devonian active continental margin setting, with prograding fan deposits of the Harmony Sandstone, overlain by Middle Pennsylvanian fanglomerates of the Battle Formation. This conformable sequence appears to preclude any major uplift within the type Antler orogen.« less

Structure of the Red Dog District, western Brooks Range, Alaska

USGS Publications Warehouse

de Vera, Jean-Pierre P.; McClay, K. R.

2004-01-01

The Red Dog district of the western Brooks Range of northern Alaska, which includes the sediment-hosted Zn-Pb-Ag ± Ba deposits at Red Dog, Su-Lik, and Anarraaq, contains one of the world's largest reserves of zinc. This paper presents a new model for the structural development of the area and shows that understanding the structure is crucial for future exploration efforts and new mineral discoveries in the district. In the Red Dog district, a telescoped Late Devonian through Jurassic continental passive margin is exposed in a series of subhorizontally stacked, internally imbricated, and regionally folded thrust sheets. These sheets were emplaced during the Middle Jurassic to Late Cretaceous Brookian orogeny and subsequently were uplifted by late tectonic activity in the Tertiary. The thrust sheet stack comprises seven tectonostratigraphically distinct allochthonous sheets, three of which have been subject to regional and detailed structural analysis. The lowermost of these is the Endicott Mountains allochthon, which is overlain by the structurally higher Picnic Creek and Kelly River allochthons. Each individual allochthon is itself internally imbricated into a series of tectonostratigraphically coherent and distinct thrust plates and subplates. This structural style gives rise to duplex development and imbrication at a range of scales, from a few meters to tens of kilometers. The variable mechanical properties of the lithologic units of the ancient passive margin resulted in changes in structural styles and scales of structures across allochthon boundaries. Structural mapping and analysis of the district indicate a dominant northwest to west-northwest direction of regional tectonic transport. Local north to north-northeast transport of thrust sheets is interpreted to reflect the influence of underlying lateral and/or oblique ramps, which may have been controlled by inherited basin margin structures. Some thrust-sheet stacking patterns suggest out-of-sequence thrusting. The west-northwest-east-southeast-trending Wrench Creek and Sivukat Mountain faults were previously interpreted to be strike-slip faults, but this study shows that they are Tertiary (Eocene?) late extensional faults with little or no lateral displacement.

Origin and implications of a thrust-bound gypsiferous unit along the western edge of Jabal Sumeini, northern Oman Mountains

NASA Astrophysics Data System (ADS)

Cooper, David J. W.; Ali, Mohammed Y.; Searle, Michael P.

2018-04-01

The Oman Mountains comprise a series of thrust sheets of Neo-Tethyan oceanic rocks that were emplaced onto the Arabian continental margin during obduction of the Semail Ophiolite during the Late Cretaceous. Three separate groups of anomalous gypsiferous bodies intrude the allochthonous units along faults over a distance of about 150 km in the Hawasina Window, Jabal Qumayrah and Jabal Sumeini. The bodies at Jabal Sumeini form a band about 4 km long and up to 100 m wide along a late-stage thrust that restacks the allochthon over a post-emplacement Maastrichtian-Palaeogene sedimentary succession. The gypsum shows evidence of flow-folding and contains numerous clasts and rafts of a range of quartzose sandstones, but with only a minor component from carbonates from the Neo-Tethyan Sumeini Group in the hanging-wall. Palaeogene limestones from the footwall succession are essentially absent. Strontium isotope ratios are high and intersect with the open ocean-water reference curve for the Late Cambrian-Ordovician and Late Miocene-Pliocene. They are also noticeably higher than the ratios from the two other gypsiferous outcrop areas in the Oman Mountains and from outcrops of Ediacaran-Early Cambrian salt domes in central Oman. However, the regional stratigraphy points towards a source of the gypsum from either an Ediacaran-Early Cambrian Ara Group salt basin or from the Lower Fars Formation (Early-Middle Miocene), and derivation of the sandstone clasts and rafts from thick Lower Palaeozoic clastic sequences. The discrepancy with the ages inferred from the strontium isotope data can be attributed to deposition of the gypsum in restricted conditions not in equilibrium with the prevailing ocean water. Two models are presented, for an Ediacaran-Early Cambrian and an Early-Middle Miocene source. While the latter cannot be wholly discounted, the stratigraphic and structural context point more strongly towards an Ediacaran-Early Cambrian Ara Group source of the gypsum. This was extruded along deep-rooted Late Cretaceous thrust faults that were reactivated during a period of Cenozoic compression, incorporating Lower Palaeozoic sandstone clasts from adjacent strata during extrusion, or during an earlier phase of possible halokinesis. This is consistent with existing models for the emplacement of the other two identified groups of gypsiferous bodies in the Oman Mountains and provides further evidence for the presence of smaller evaporite basins between the major Hormuz and central/ southern Oman salt basins.

Geophysical interpretations of the Libby thrust belt, northwestern Montana

USGS Publications Warehouse

Kleinkopf, M. Dean; with sections by Harrison, Jack Edward; Stanley, W.D.

1997-01-01

Interpretations of gravity and aeromagnetic anomaly data, supplemented by results from two seismic reflection profiles and five magnetotelluric soundings, were used to study buried structure and lithology of the Libby thrust belt of northwestern Montana. The gravity anomaly data show a marked correlation with major structures. The Purcell anticlinorium and the Sylvanite anticline are very likely cored by stacks of thrust slices of dense crystalline basement rocks that account for the large gravity highs across these two structures. Gravity anomaly data for the Cabinet Mountains Wilderness show a string of four broad highs. The principal magnetic anomaly sources are igneous intrusive rocks, major fault zones, and magnetite-bearing sedimentary rocks of the Ravalli Group. The most important magnetic anomalies in the principal study area are five distinct positive anomalies associated with Cretaceous or younger cupolas and stocks.

The magnitude 6.7 Northridge, California, earthquake of 17 January 1994

USGS Publications Warehouse

Jones, L.; Aki, K.; Boore, D.; Celebi, M.; Donnellan, A.; Hall, J.; Harris, R.; Hauksson, E.; Heaton, T.; Hough, S.; Hudnut, K.; Hutton, K.; Johnston, M.; Joyner, W.; Kanamori, H.; Marshall, G.; Michael, A.; Mori, J.; Murray, M.; Ponti, D.; Reasenberg, P.; Schwartz, D.; Seeber, L.; Shakal, A.; Simpson, R.; Thio, H.; Tinsley, J.; Todorovska, M.; Trifunac, M.; Wald, D.; Zoback, M.L.

1994-01-01

The most costly American earthquake since 1906 struck Los Angeles on 17 January 1994. The magnitude 6.7 Northridge earthquake resulted from more than 3 meters of reverse slip on a 15-kilometer-long south-dipping thrust fault that raised the Santa Susana mountains by as much as 70 centimeters. The fault appears to be truncated by the fault that broke in the 1971 San Fernando earthquake at a depth of 8 kilometers. Of these two events, the Northridge earthquake caused many times more damage, primarily because its causative fault is directly under the city. Many types of structures were damaged, but the fracture of welds in steel-frame buildings was the greatest surprise. The Northridge earthquake emphasizes the hazard posed to Los Angeles by concealed thrust faults and the potential for strong ground shaking in moderate earthquakes.The most costly American earthquake since 1906 struck Los Angeles on 17 January 1994. The magnitude 6.7 Northridge earthquake resulted from more than 3 meters of reverse slip on a 15-kilometer-long south-dipping thrust fault that raised the Santa Susana mountains by as much as 70 centimeters. The fault appears to be truncated by the fault that broke in the 1971 San Fernando earthquake at a depth of 8 kilometers. Of these two events, the Northridge earthquake caused many times more damage, primarily because its causative fault is directly under the city. Many types of structures were damaged, but the fracture of welds in steel-frame buildings was the greatest surprise. The Northridge earthquake emphasizes the hazard posed to Los Angeles by concealed thrust faults and the potential for strong ground shaking in moderate earthquakes.

Deformation during terrane accretion in the Saint Elias orogen, Alaska

USGS Publications Warehouse

Bruhn, R.L.; Pavlis, T.L.; Plafker, G.; Serpa, L.

2004-01-01

The Saint Elias orogen of southern Alaska and adjacent Canada is a complex belt of mountains formed by collision and accretion of the Yakutat terrane into the transition zone from transform faulting to subduction in the northeast Pacific. The orogen is an active analog for tectonic processes that formed much of the North American Cordillera, and is also an important site to study (1) the relationships between climate and tectonics, and (2) structures that generate large- to great-magnitude earthquakes. The Yakutat terrane is a fragment of the North American plate margin that is partly subducted beneath and partly accreted to the continental margin of southern Alaska. Interaction between the Yakutat terrane and the North American and Pacific plates causes significant differences in the style of deformation within the terrane. Deformation in the eastern part of the terrane is caused by strike-slip faulting along the Fairweather transform fault and by reverse faulting beneath the coastal mountains, but there is little deformation immediately offshore. The central part of the orogen is marked by thrusting of the Yakutat terrane beneath the North American plate along the Chugach-Saint Elias fault and development of a wide, thin-skinned fold-and-thrust belt. Strike-slip faulting in this segment may he localized in the hanging wall of the Chugach-Saint Elias fault, or dissipated by thrust faulting beneath a north-northeast-trending belt of active deformation that cuts obliquely across the eastern end of the fold-and-thrust belt. Superimposed folds with complex shapes and plunging hinge lines accommodate horizontal shortening and extension in the western part of the orogen, where the sedimentary cover of the Yakutat terrane is accreted into the upper plate of the Aleutian subduction zone. These three structural segments are separated by transverse tectonic boundaries that cut across the Yakutat terrane and also coincide with the courses of piedmont glaciers that flow from the topographic backbone of the Saint Elias Mountains onto the coastal plain. The Malaspina fault-Pamplona structural zone separates the eastern and central parts of the orogen and is marked by reverse faulting and folding. Onshore, most of this boundary is buried beneath the western or "Agassiz" lobe of the Malaspina piedmont glacier. The boundary between the central fold-and-thrust belt and western zone of superimposed folding lies beneath the middle and lower course of the Bering piedmont glacier. ?? 2004 Geological Society of America.

Preliminary geologic map of the San Guillermo Mountain Quadrangle, Ventura County, California

USGS Publications Warehouse

Minor, S.A.

1999-01-01

New 1:24,000-scale geologic mapping in the Cuyama 30' x 60' quadrangle, in support of the USGS Southern California Areal Mapping Project (SCAMP), is contributing to a more complete understanding of the stratigraphy, structure, and tectonic evolution of the complex junction area between the NW-striking Coast Ranges and EW-striking western Transverse Ranges. The 1:24,000-scale geologic map of the San Guillermo Mountain quadrangle is one of six contiguous 7 1/2' quadrangle geologic maps in the eastern part of the Cuyama map area being compiled for a more detailed portrayal and reevaluation of geologic structures and rock units shown on previous geologic maps of the area (e.g., Dibblee, 1979). The following observations and interpretations are based on the new San Guillermo Mountain geologic compilation: (1) The new geologic mapping in the northern part of the San Guillermo Mountain quadrangle allows for reinterpretation of fault architecture that bears on potential seismic hazards of the region. Previous mapping had depicted the eastern Big Pine fault (BPF) as a northeast-striking, sinistral strike-slip fault that extends for 30 km northeast of the Cuyama River to its intersection with the San Andreas fault (SAF). In contrast the new mapping indicates that the eastern BPF is a thrust fault that curves from a northeast strike to an east strike, where it is continuous with the San Guillermo thrust fault, and dies out further east about 15 km south of the SAF. This redefined segment of the BPF is a south-dipping, north-directed thrust, with dominantly dip slip components (rakes > 60 deg.), that places Middle Eocene marine rocks (Juncal and Matilija Formations) over Miocene through Pliocene(?) nonmarine rocks (Caliente, Quatal, and Morales Formations). Although a broad northeast-striking fault zone, exhibiting predominantly sinistral components of slip (rakes < 45 deg.), extends to the SAF as previously mapped, the fault zone does not connect to the southwest with the BPF but instead curves into a southwest-directed thrust fault system a short distance north of the BPF. Oligocene to Pliocene(?) nonmarine sedimentary and volcanic rocks of the Plush Ranch, Caliente, and Morales(?) Formations are folded on both sides of this fault zone (informally named the Lockwood Valley fault zone [LVFZ] on the map). South-southeast of the LVFZ overturned folds have southward vergence. Several moderate-displacement (< 50 m), mainly northwest-dipping thrust and reverse faults, exhibiting mostly sinistral-oblique slip, flank and strike parallel to the overturned folds. The fold vergence and thrust direction associated with the LVFZ is opposite to that of the redefined BPF, providing further evidence that the two faults are distinct structures. These revised fault interpretations bring into question earlier estimates of net sinistral strike-slip displacement of as much as 13 km along the originally defined eastern BPF, which assumed structural connection with the LVFZ. Also, despite sparse evidence for repeated Quaternary movement on the LVFZ (e.g., Dibblee, 1982), the potential for a large earthquake involving coseismic slip on both the LVFZ and the central BPF to the southwest may not be as great as once believed. (2) Several generations of Pleistocene and younger dissected alluvial terrace and fan deposits sit at various levels above modern stream channels throughout the quadrangle. These deposits give testimony to the recent uplift and related fault deformation that has occurred in the area. (3) A vast terrane of Eocene marine sedimentary rocks (Juncal and Matilija Formations and Cozy Dell Shale) exposed south of the Big Pine fault forms the southern two-thirds of the San Guillermo Mountain quadrangle. Benthic foraminifers collected from various shale intervals within the Juncal Formation indicate a Middle Eocene age (Ulatisian) for the entire formation (K. McDougall, unpub. data, 1998) and deposition at paleodepths as great as 2,000 m (i.e., lowe

A possible explanation for foreland thrust propagation

NASA Astrophysics Data System (ADS)

Panian, John; Pilant, Walter

1990-06-01

A common feature of thin-skinned fold and thrust belts is the sequential nature of foreland directed thrust systems. As a rule, younger thrusts develop in the footwalls of older thrusts, the whole sequence propagating towards the foreland in the transport direction. As each new younger thrust develops, the entire sequence is thickened; particularly in the frontal region. The compressive toe region can be likened to an advancing wave; as the mountainous thrust belt advanced the down-surface slope stresses drive thrusts ahead of it much like a surfboard rider. In an attempt to investigate the stresses in the frontal regions of thrustsheets, a numerical method has been devised from the algorithm given by McTigue and Mei [1981]. The algorithm yields a quickly computed approximate solution of the gravity- and tectonic-induced stresses of a two-dimensional homogeneous elastic half-space with an arbitrarily shaped free surface of small slope. A comparison of the numerical method with analytical examples shows excellent agreement. The numerical method was devised because it greatly facilitates the stress calculations and frees one from using the restrictive, simple topographic profiles necessary to obtain an analytical solution. The numerical version of the McTigue and Mei algorithm shows that there is a region of increased maximum resolved shear stress, τ, directly beneath the toe of the overthrust sheet. Utilizing the Mohr-Coulomb failure criterion, predicted fault lines are computed. It is shown that they flatten and become horizontal in some portions of this zone of increased τ. Thrust sheets are known to advance upon weak decollement zones. If there is a coincidence of increased τ, a weak rock layer, and a potential fault line parallel to this weak layer, we have in place all the elements necessary to initiate a new thrusting event. That is, this combination acts as a nucleating center to initiate a new thrusting event. Therefore, thrusts develop in sequence towards the foreland as a consequence of the stress concentrating abilities of the toe of the thrust sheet. The gravity- and tectonic-induced stresses due to the surface topography (usually ignored in previous analyses) of an advancing thrust sheet play a key role in the nature of shallow foreland thrust propagation.

Source Parameters for Moderate Earthquakes in the Zagros Mountains with Implications for the Depth Extent of Seismicity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adams, A; Brazier, R; Nyblade, A

2009-02-23

Six earthquakes within the Zagros Mountains with magnitudes between 4.9 and 5.7 have been studied to determine their source parameters. These events were selected for study because they were reported in open catalogs to have lower crustal or upper mantle source depths and because they occurred within an area of the Zagros Mountains where crustal velocity structure has been constrained by previous studies. Moment tensor inversion of regional broadband waveforms have been combined with forward modeling of depth phases on short period teleseismic waveforms to constrain source depths and moment tensors. Our results show that all six events nucleated withinmore » the upper crust (<11 km depth) and have thrust mechanisms. This finding supports other studies that call into question the existence of lower crustal or mantle events beneath the Zagros Mountains.« less

Using U-Th-Pb petrochronology to determine rates of ductile thrusting: Time windows into the Main Central Thrust, Sikkim Himalaya

NASA Astrophysics Data System (ADS)

Mottram, Catherine M.; Parrish, Randall R.; Regis, Daniele; Warren, Clare J.; Argles, Tom W.; Harris, Nigel B. W.; Roberts, Nick M. W.

2015-07-01

Quantitative constraints on the rates of tectonic processes underpin our understanding of the mechanisms that form mountains. In the Sikkim Himalaya, late structural doming has revealed time-transgressive evidence of metamorphism and thrusting that permit calculation of the minimum rate of movement on a major ductile fault zone, the Main Central Thrust (MCT), by a novel methodology. U-Th-Pb monazite ages, compositions, and metamorphic pressure-temperature determinations from rocks directly beneath the MCT reveal that samples from 50 km along the transport direction of the thrust experienced similar prograde, peak, and retrograde metamorphic conditions at different times. In the southern, frontal edge of the thrust zone, the rocks were buried to conditions of 550°C and 0.8 GPa between 21 and 18 Ma along the prograde path. Peak metamorphic conditions of 650°C and 0.8-1.0 GPa were subsequently reached as this footwall material was underplated to the hanging wall at 17-14 Ma. This same process occurred at analogous metamorphic conditions between 18-16 Ma and 14.5-13 Ma in the midsection of the thrust zone and between 13 Ma and 12 Ma in the northern, rear edge of the thrust zone. Northward younging muscovite 40Ar/39Ar ages are consistently 4 Ma younger than the youngest monazite ages for equivalent samples. By combining the geochronological data with the >50 km minimum distance separating samples along the transport axis, a minimum average thrusting rate of 10 ± 3 mm yr-1 can be calculated. This provides a minimum constraint on the amount of Miocene India-Asia convergence that was accommodated along the MCT.

Chapter C in Geological Survey research 1967

USGS Publications Warehouse

1967-01-01

Low-grade metamorphic rocks of the blueschist facies grade upward to the sole of a great thrust fault along the eastern margin of the Coast Ranges in northern California and southwestern Oregon. The gradation is defined by three textural zones of increasing reconstitution in metagraywacke, and by two metamorphic mineral zones, lawsonite and pumpellyite. The metagraywacke of textural zones 1 and 2 is clearly Franciscan Formation on the basis of lithology and age, and grades into thoroughly reconstituted rocks of textural zone 3 that herein are named the South Fork Mountain Schist. The blueschist probably formed in a zone of cataclasis and anomalously high water pressures under the thrust fault, rather than in the generally postulated zone of extreme depth of burial. Water in excess of that required to form pumpellyite and lawsonite was available for serpentinization of ultramafic rocks emplaced in the thrust fault.

High sedimentation rates and thrust fault modulation: Insights from ocean drilling offshore the St. Elias Mountains, southern Alaska

NASA Astrophysics Data System (ADS)

Worthington, Lindsay L.; Daigle, Hugh; Clary, Wesley A.; Gulick, Sean P. S.; Montelli, Aleksandr

2018-02-01

The southern Alaskan margin offshore the St. Elias Mountains has experienced the highest recorded offshore sediment accumulation rates globally. Combined with high uplift rates, active convergence and extensive temperate glaciation, the margin provides a superb setting for evaluating competing influences of tectonic and surface processes on orogen development. We correlate results from Integrated Ocean Drilling Program (IODP) Expedition 341 Sites U1420 and U1421 with regional seismic data to determine the spatial and temporal evolution of the Pamplona Zone fold-thrust belt that forms the offshore St. Elias deformation front on the continental shelf. Our mapping shows that the pattern of active faulting changed from distributed across the shelf to localized away from the primary glacial depocenter over ∼300-780 kyrs, following an order-of-magnitude increase in sediment accumulation rates. Simple Coulomb stress calculations show that the suppression of faulting is partially controlled by the change in sediment accumulation rates which created a differential pore pressure regime between the underlying, faulted strata and the overlying, undeformed sediments.

Foreshock occurrence rates before large earthquakes worldwide

USGS Publications Warehouse

Reasenberg, P.A.

1999-01-01

Global rates of foreshock occurrence involving shallow M ??? 6 and M ??? 7 mainshocks and M ??? 5 foreshocks were measured, using earthquakes listed in the Harvard CMT catalog for the period 1978-1996. These rates are similar to rates ones measured in previous worldwide and regional studies when they are normalized for the ranges of magnitude difference they each span. The observed worldwide rates were compared to a generic model of earthquake clustering, which is based on patterns of small and moderate aftershocks in California, and were found to exceed the California model by a factor of approximately 2. Significant differences in foreshock rate were found among subsets of earthquakes defined by their focal mechanism and tectonic region, with the rate before thrust events higher and the rate before strike-slip events lower than the worldwide average. Among the thrust events a large majority, composed of events located in shallow subduction zones, registered a high foreshock rate, while a minority, located in continental thrust belts, measured a low rate. These differences may explain why previous surveys have revealed low foreshock rates among thrust events in California (especially southern California), while the worldwide observations suggest the opposite: California, lacking an active subduction zone in most of its territory, and including a region of mountain-building thrusts in the south, reflects the low rate apparently typical for continental thrusts, while the worldwide observations, dominated by shallow subduction zone events, are foreshock-rich.

Palaeomagnetic evidence for post-thrusting tectonic rotation in the Southeast Pyrenees, Spain

NASA Astrophysics Data System (ADS)

Keller, P.; Lowrie, W.; Gehring, A. U.

1994-12-01

The structural framework of the Southeast Pyrenees led to two conflicting interpretations—thrust tectonics vs. wrench tectonics—to explain the geometry of this mountain range. In the present study palaeomagnetic data are presented in an attempt to resolve this conflict. The data reveal different magnetisation directions that indicate tectonic rotations about vertical axes. By means of a regionally homogeneous pattern of rotation, three tectonic units could be distinguished in the Southeast Pyrenees. The Internal Unit in the north reveals no rotation since the Permian. The External Unit to the south shows anticlockwise rotation of 25°, younger than the Early Oligocene. The Pedraforca Unit, placed on the External Unit, shows 57° clockwise rotation which can be assigned to the Neogene. The anticlockwise rotation of the External Unit can be explained by differential compression during the last phase of Pyrenean thrusting, whereas the clockwise rotation of the Pedraforca Unit can be interpreted by post-thrusting tectonics. The rotation pattern of the Southeast Pyrenees provides evidence for both Cretaceous to Paleogene N-S compression and Neogene right-lateral wrench tectonics.

Two new ductile microscopic shear sense indicators from the Oman Mountains

NASA Astrophysics Data System (ADS)

Scharf, Andreas; Mattern, Frank; Pracejus, Bernhard

2017-04-01

The new shear sense indicators were observed in two different tectonic settings. The first one occurs in mylonitized Jurassic limestone on the northern flank of the Jebel Akhdar Dome (eastern Oman Mountains) and is associated with top-to-the-NNE extension. The second one was discovered in mylonitized plagiogranite (trondhjemite) with vertical to subvertical foliation and strike-slip deformation within harzburgite of the Semail Ophiolite in Wadi Fizh (northwestern Oman Mountains). The carbonate mylonite displays shear planes, in thin, flat and parallel laminations with a compositional aspect as there are alternations between pure calcite laminae and dark laminae of accumulated limestone impurities (iron compounds, clay). Despite the fact that the carbonate mylonite is associated with extension, the shear sense criterion is linked to top-to-the-NNE microthrusts, involving shortening of the dark laminae. The thrusts form an acute angle in relation to the lamination. Thrusting between segments of these, microthrusts created pull-aparts whose voids remained temporarily open cavities but were eventually filled with drusy calcite cement. The shear sense is revealed by (1) the shortening and related imbrication of the thrust laminae, (2) the pull-apart structures and (3) drag folds at either end of the microthrusts. The shear is also confirmed by independent ductile and brittle macroscopic shear sense criteria in the same outcrop, such as drag folds, Riedel shears and mineral steps. These new shear sense fabrics measure approximately 0.5mm in width and 1mm in length. The mylonitized granite contains large (2mm long axis) plagioclase porphyroclasts. We encountered a rotated plagioclase crystal whose twin lamellae have been dragged by the rotational motion during high-temperature conditions. Drag folds occur on either end of the lamellae/crystal. As a result an "S" shape is produced by counterclockwise rotation and sinistral shear, respectively. The observed shear sense is confirmed by synthetically sheared K-feldspar and feldspar porphyroclast systems. "Z" shapes are expected to develop in case of opposite rotation and shearing.

Structural implications of an offset Early Cretaceous shoreline in northern California

USGS Publications Warehouse

Jones, D.L.; Irwin, W.P.

1971-01-01

Recognition of a nonmarine to marine transition in sedimentary rocks at Glade Creek and Big Bar in the southern Klamath Mountains permits reconstruction of the approximate position of a north-trending Early Cretaceous (Valanginian) shoreline. At the southern end of the Klamath Mountains, the shoreline is displaced 60 mi or more to the east by a west-northwest-trending fault zone. South of this fault zone the shoreline is buried at a much lower level beneath late Cenozoic rocks in the Great Valley. This large displacement probably is the result of differential movement along a system of left-lateral tear faults in the upper plate of the Coast Range thrust. The westward bulge of the Klamath arc also may have resulted from this faulting, as the amount and direction of the bulge is comparable with the displacement of the Valanginian shoreline.Basal clastic strata at both Glade Creek and Big Bar contain abundant fresh-water or brackish-water clams, many of which consist of unabraded paired valves. These are conformably overlain by Valanginian marine strata containing Buchia crassicollis solida.The position of the Valanginian shoreline beneath the Great Valley cannot be directly observed because it is buried by thick late Cenozoic deposits. However, its approximate westernmost limit must lie between the outcrop belt of marine strata on the west side of the valley and drill holes to basement on the east side, in which equivalent strata are absent.Franciscan rocks containing Valanginian fossils occur 10 mi southwest of Glade Creek, but these are deep-water marine eugeosynclinal rocks that were deposited far to the west of the shoreline. The deformation responsible for the displacement of the Valanginian shoreline and juxtaposition of the Franciscan rocks and Klamath Mountain basement rocks involved eastward under-thrusting of the Franciscan beneath the Coast Range thrust contemporaneous with differential movement along tear faults within the upper plate.

TRAY MOUNTAIN ROADLESS AREA, GEORGIA.

USGS Publications Warehouse

Nelson, Arthur E.; Chatman, Mark L.

1984-01-01

A mineral survey indicates that the Tray Mountain Roadless Area, Georgia has little promise for the occurrence of metallic mineral resources. Rocks underlying the Tray Mountain Roadless Area are suitable for crushed rock or aggregate; however, other sources for these materials are available closer to present markets. There is a possibility for the occurrence of hydrocarbon resources underlying the area at great depth, but no hydrocarbon potential was identified. Detailed studies are needed to establish the presence or absence and mineral-resource potential of olivine, nickel, cobalt, and chrome in the two mafic-ultramafic bodies in the Hayesville thrust sheet. The cause of the lead anomaly in pan concentrate samples taken from the southwest part of the roadless area has not been established; the mineral residence and source of the anomaly remain to be determined.

Major, trace element and stable isotope geochemistry of synorogenic breccia bodies, Ellsworth Mountains, Antarctica

USGS Publications Warehouse

Craddock, J.P.; McGillion, M.S.; Webers, G.F.

2007-01-01

Cambrian carbonates in the Heritage Range of the Ellsworth Mountains, West Antarctica host a series of carbonate-rich breccia bodies that formed contemporaneously with the Permian Gondwanide orogen. The breccia bodies had a three-stage genesis, with the older breccias containing Cambrian limestone (and marble) clasts supported by calcite, whereas the younger breccias are nearly clast-free and composed entirely of matrix calcite. Breccia clasts, calcite matrix and detrital matrix samples were analyzed using x-ray fluorescence (major and trace elements), x-ray diffraction, and stable isotopes (C, O) and suggest that the breccias formed as part of a closed geochemical system, at considerable depth, within the Cambrian limestone host as the Ellsworth Mountains deformed into a fold-and-thrust belt along the margin of Gondwana

Interpretation of recent gravity profiles over the ophiolite belt, Northern Oman Mountains, United Arab Emirates

NASA Astrophysics Data System (ADS)

Khattab, M. M.

1993-04-01

The compiled Bouguer gravity anomaly map over parts of the ophiolite rocks of the Northern Oman Mountains suggests the existence of three partially serpentinized nappes: two along the Gulf of Oman coast with axes near Dadnah, near Fujira and the third 17 km SSE of Masafi. Modeling of the subsurface geology, beneath two gravity profiles (Diba-Kalba and Masafi-Fujira), is based on the occurrence (field evidence) of multiphase low-angle thrusting of the members of the Tethyan lithosphere in northern and Oman Mountains. An assumed crustal model at the Arabian continental margin, beneath the Masafi-Fujira profile, is made to explain an intense gravity gradient. Gravity interpretation is not inconsistent with a gliding mechanism for obduction of the ophiolite on this part of the Arabian continental margin.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Montgomery, S.L.

Recent discovery of natural gas in sandstones of the Jackfork Group of southeastern Oklahoma has led to revised interpretations of hydrocarbon potential in the Ouachita thrust province of eastern Oklahoma. Jackfork reservoirs consist of fine to very fine grained, submarine-fan lobe sandstones with low matrix permeability and porosity. Production is dependent upon natural fractures, enhanced in most cases by artificial stimulation. Individual wells have produced at rates of 1.3-5.7 Mcf per day and possess estimated reserves in the range of 2.0-7.6 Gcf. Hyperbolic decline suggests gas contribution from the matrix, possibly due to the presence of microfractures. Drilling has concentratedmore » on two subsidiary thrust blocks in the hanging wall of the Ti Valley thrust, southern Latimer County. However, recent outcrop, petrographic, and sedimentological analyses have shown that traditional depositional models of the Jackfork are overly limited and that potential Jackfork reservoirs exist across a broad area to the south of the current play. Such analyses have revealed the existence of thick, medium-coarse-grained channel sequences at a number of localities in the Lynn Mountain syncline. Similar sequences may also exist well to the south, in the Boktukola syncline, where thick sand intervals have been identified. Petrographic study of samples from the Lynn Mountain syncline suggests that channel sequences may have significantly higher reservoir quality than is found in productive Jackfork sandstones to the north. Traditional assumptions postulating low regional hydrocarbon potential for the Jackfork therefore stand in need of revision.« less

Unraveling the volcanic and post-volcanic history at Upsal Hogback, Fallon, Nevada, USA

NASA Astrophysics Data System (ADS)

Anderson, E.; Cousens, B.

2013-12-01

Upsal Hogback is a < 25 ka phreatomagmatic volcanic center situated near Fallon, Nevada. The volcano neighbors two other young volcanic complexes: the Holocene Soda Lakes maars and Rattlesnake Hill, a ~ 1 Ma volcanic neck (Shevenell et al., 2005). These volcanoes lie on the transition between the Sierra Nevada and the Basin and Range province, as well as on the edge of the Walker Lane. Upsal Hogback includes two to four vents, fewer than mapped by Morrison (1964), and can be divided into north (one vent) and south (three potential vents) complexes. The vents all produced phreatomagmatic eruptions resulting in tuff rings composed primarily of coarse, indurated lapilli tuffs with abundant volcanic bombs. Ash tuffs are infrequent, as are structures such as crossbedding. The bombs and lapilli include olivine and plagioclase phenocrysts. The basalts are alkaline and have intraplate-type normalized incompatible element patterns. Both complexes are enriched in LREE compared to HREE, though the north complex overall has lower concentrations of the REE. The flat HREE pattern is indicative of spinel peridotite mantle source. Epsilon Nd values for the north complex are +2.50+/-0.02 and for the south complex are +2.83+/-0.02. The magmas appear to have an enriched asthenospheric mantle source. Bomb samples show that eruptions from the two complexes are geochemically distinguishable both in major and trace elements, suggesting that the two complexes tapped different magma types during eruptions that likely occurred at slightly different times. The proximity of Upsal Hogback to Fallon makes constraining its age important to characterize the hazard to the city. It lies above the Wono ash bed, dated at 25,000 years (Fultz et al., 1983), and tufa deposited over the edifice is dated at 11,100 +/- 100 and 8,600 +/- 200 years (Benson et al., 1992; Broecker and Kaufman, 1965). 40Ar/39Ar total gas age by Shevenell et al. (2005) dated the volcano at 0.60 +/- 0.09 Ma, but with no plateau or isochron, and is thus unreliable. The ash bed and tufa ages show that the eruptions would have occurred during the late history of glacial Lake Lahontan. The evidence for primarily subaerial or shallow subaqueous eruptions, including abundant bomb sags and armored lapilli, demonstrate that most of the volcanism occurred during a low stand in lake level history. Some upper tuff units have been heavily altered to palagonite, which establishes that there was substantial water present during some of the later eruptions. The upper edifice has been significantly modified by slumping of the lapilli tuffs during or after of the eruptions, as indicated by the wildly varying strikes and dips found in adjacent lapilli tuff blocks. Lake Lahontan has substantially altered the morphology of the volcano through wave action and shoreline erosion, as well as tufa deposition, since the eruption and emplacement of the tuffs. The edifice has gone through significant changes during its post-eruptive history that mask many of its original features; it was possible that it was a tuff cone that has been modified into a tuff ring.

Extensional reactivation of the Chocolate Mountains subduction thrust in the Gavilan Hills of southeastern California

USGS Publications Warehouse

Oyarzabal, F.R.; Jacobson, C.E.; Haxel, G.B.

1997-01-01

The NE vergent Chocolate Mountains fault of south-eastern California has been interpreted as either a subduction thrust responsible for burial and prograde metamorphism of the ensimatic Orocopia Schist or as a normal fault involved in the exhumation of the schist. Our detailed structural analysis in the Gavilan Hills area provides new evidence to confirm the latter view. A zone of deformation is present at the top of the Orocopia Schist in which lineations are parallel to those in the upper plate of the Chocolate Mountains fault but oblique to ones at relatively deep levels in the schist. Both the Orocopia Schist and upper plate contain several generations of shear zones that show a transition from crystalloblastic through mylonitic to cataclastic textures. These structures formed during retrograde metamorphism and are considered to record the exhumation of the Orocopia Schist during early Tertiary time as a result of subduction return flow. The Gatuna fault, which places low-grade, supracrustal metasediments of the Winterhaven Formation above the gneisses of the upper plate, also seems to have been active at this time. Final unroofing of the Orocopia Schist occurred during early to middle Miocene regional extension and may have involved a second phase of movement on the Gatuna fault. Formation of the Chocolate Mountains fault during exhumation indicates that its top-to-the-NE sense of movement provides no constraint on the polarity of the Orocopia Schist subduction zone. This weakens the case for a previous model involving SW dipping subduction, while providing support for the view that the Orocopia Schist is a correlative of the Franciscan Complex.

Development of an arcuate fold-thrust belt as a result of basement configuration: an example from the Rocky Mountain Front Range, Montana

NASA Astrophysics Data System (ADS)

Burberry, C. M.; Cannon, D. L.; Engelder, T.; Cosgrove, J. W.

2010-12-01

The Sawtooth Range forms part of the Montana Disturbed Belt in the Front Ranges of the Rocky Mountains, along strike from the Alberta Syncline in the Canadian Rockies. The belt developed in the footwall to the Lewis Thrust during the Sevier orogeny and is similar in deformation style to the Canadian Foothills, with a series of stacked thrust sheets carrying Palaeozoic carbonates. The Sawtooth Range can be divided into an inner and outer deformed belt, separated by exposed fold structures in the overlying clastic sequence. Structures in the deformed belts plunge into the culmination of the NE-trending Scapegoat-Bannatyne trend, part of the Great Falls Tectonic Zone (GFTZ). Other mapped faults, including the Pendroy fault zone to the north, parallel this trend. A number of mechanisms have been proposed for the development of primary arcs in fold-thrust belts, including linkage of two thrust belts with different strikes, differential transport of segments of the belt, the geometry of the indentor, local plate heterogeneity and pre-existing basement configuration. Arcuate belts may also develop as a result of later bending of an initially straight orogen. In the Swift Dam area, part of the outer belt of the Sawtooth Range, the strike of the belt changes from 165 to 150. This apparent change in strike is accommodated by a sinistral lateral ramp in the Swift Dam Thrust. In addition, this outer belt becomes broader to the north in the Swift Dam region. However, the outer belt becomes extremely narrow in the Teton Canyon region to the south, and the deformation front is characterised by an intercutaneous wedge structure, rather than the trailing-edge imbricate fan seen to the north. A similar imbricate fan structure is seen to the south, in the Sun River Canyon region, corresponding well to the classic model of a deformation belt governed by a dominant thrust sheet, after Boyer & Elliot. The Sawtooth Range can be described as an active-roof duplex in the footwall to the dominant Lewis thrust slab. Analysis of the transport directions of the thrust sheets in the Range implies that the inner arcuate belt is a secondary arc, but that the later, outer arcuate belt formed by divergent transport. This two-stage development model is strongly influenced by the basement configuration. The deformation front of the outer arc is governed by NNW-striking Proterozoic normal fault structures. The entire Sawtooth Range duplex is uplifted over an earlier, NE-trending basement structure (the GFTZ), forming a termination in the Lewis slab. The interaction of these two fault trends allows the development of a linear deformation front in the foreland Jurassic-Cretaceous sequence, but an arcuate belt in the Palaeozoic carbonate sheets. Thus, the width and style of the outer arcuate belt also varies along the strike of the belt.

The Dandridge-Vonore Fault Zone in the Eastern Tennessee Seismic Zone (and Rejuvenation of the Smokies?)

NASA Astrophysics Data System (ADS)

Cox, R. T.; Hatcher, R. D., Jr.; Forman, S. L.; Gamble, E. D. S.; Warrell, K. F.

2017-12-01

The eastern Tennessee seismic zone (ETSZ) trends 045o from NE Alabama and NW Georgia through Tennessee to SE Kentucky, and seismicity is localized 5-26 km deep in the basement. The ETSZ is the second most seismically active region in North America east of the Rocky Mountains, although no historic earthquakes larger than Mw 4.8 have been recorded here. Late Quaternary paleoiseismic evidence suggests that the ETSZ is capable of M7+ earthquakes and that neotectonic faults may have significantly influenced the regional relief. We have identified an 80 km-long, 060o-trending corridor in eastern Tennessee that contains collinear northeast-striking thrust, strike-slip, and normal Quaternary faults with displacements of 1-2 m, herein termed the Dandridge-Vonore fault zone (DVFZ). French Broad River alluvium in the northeast DVFZ near Dandridge, TN, is displaced by a 050o-striking, SE-dipping thrust fault and by a set of related fissures that record at least two significant post 25 ka paleo-earthquakes. Southwest of Dandridge near Alcoa, TN, a 060o-striking, SE-dipping thrust fault cuts Little River alluvium and records two significant post-15 ka paleo-earthquakes. Farther southwest at Vonore, colluvium with alluvial cobbles is thrust >1 m by a 057o-striking, steeply SE-dipping fault that may also have a significant strike-slip component, and Little Tennessee River alluvium is dropped >2 m along a 070o- striking normal fault. The DVFZ partly overlaps and is collinear with a local trend of maximum seismicity that extends 30 km farther SW of the DVFZ (as currently mapped), for a total length of 110 km. The DVFZ is coincident with a steep gradient in S-wave velocities (from high velocity on the SE to low velocity on the NW) at mid-crustal depths of 20 to 24 km, consistent with a fault and source zone at hypocentral depths in the crystalline basement. Moreover, the DVFZ parallels the NW foot of Blue Ridge Mountains, and the sense of thrusting at all sites of Quaternary faulting in the DVFZ is consistent with uplift of the Blue Ridge.

Team Teaching and Cooperative Groups in Abstract Algebra: Nurturing a New Generation of Confident Mathematics Teachers

ERIC Educational Resources Information Center

Grassl, R.; Mingus, T. T. Y.

2007-01-01

Experiences in designing and teaching a reformed abstract algebra course are described. This effort was partially a result of a five year statewide National Science Foundation (NSF) grant entitled the Rocky Mountain Teacher Enhancement Collaborative. The major thrust of this grant was to implement reform in core mathematics courses that would…

Structural profile reconstructions and thermal metamorphic evolution in the slate belt of southern Hsuehshan Range in the active Taiwan mountain belt

NASA Astrophysics Data System (ADS)

Wu, Yu; Chen, Chih-Tung; Lee, Jian-Cheng; Shyu, J. Bruce H.

2017-04-01

The fate of passive continental margin in collisional orogens is crucial in understanding tectonic evolution of mountain belts. The active arc-continent collision of Taiwan is considered as a model case in studying mountain building processes, and largely consists of deformed margin basement and cover series. Among the whole orogeny belt, the slate belt of the Hsuehshan Range (HR) is a prominent large-scale pop-up structural on the prowedge part of the orogen, and is composed of metamorphosed Eocene to Miocene sediments which experienced only the Neogene Taiwan orogeny after diagenesis in margin graben. Characterizing the metamorphic history of the HR is essential for reconstructing its geological evolution during the mountain building processes. However, previous studies were mostly focused on northern and central HR, structural investigation coupled with metamorphic documentation in the southern part of HR, which is the most active part of the orogeny belt, is therefore targeted in this work. Since carbonaceous material is common in pelitic protolith of HR slates, the Raman spectrum of carbonaceous material (RSCM) measuring the rock peak temperature is chosen for quantitative thermal metamorphic documentation. In this study, we reconstruct a geological structural profile in western central Taiwan across the prowedge part of the mountain belt containing the southern HR by combining the surface geological data, well log records and published seismic reflection profiles. Although most of the existing data are concentrated in the fold-and-thrust belt, they are now reinforced by new field structural measurements and RSCM samples in the southern HR. In total 27 RSCM samples were collected along 2 transects perpendicular to the average strike with a dense interval about 2 km. The results allow us to map peak temperature distribution across southern HR, and provide new constraints for structural profile reconstruction and reappraisal of the structural evolution of the HR and neighboring fold-and-thrust belt. As shown in the previous thermal metamorphic investigation, we expected that southern HR strata acquired highest temperature during its burial stage than the orogenic stage like their central HR counterparts, thus experiencing mostly retrograde metamorphism in the entire mountain building processes.

Inherited crustal features and tectonic blocks of the Transantarctic Mountains: An aeromagnetic perspective (Victoria Land, Antarctica)

NASA Astrophysics Data System (ADS)

Ferraccioli, F.; Bozzo, E.

1999-11-01

Aeromagnetic images covering a sector of the Transantarctic Mountains in Victoria Land as well as the adjacent Ross Sea are used to study possible relationships between tectonic blocks along the Cenozoic and Mesozoic West Antarctic rift shoulder and prerift features inherited mainly from the Paleozoic terranes involved in the Ross Orogen. The segmentation between the Prince Albert Mountains block and the Deep Freeze Range-Terra Nova Bay region is related to an inherited NW to NNW ice-covered boundary, which we name the "central Victoria Land boundary." It is interpreted to be the unexposed, southern continuation of the Ross age back arc Exiles thrust system recognized at the Pacific coast. The regional magnetic high to the west of the central Victoria Land boundary is attributed to Ross age calc-alkaline back arc intrusives forming the in-board Wilson "Terrane," thus shifting the previously interpreted Precambrian "shield" at least 100 km farther to the west. The high-frequency anomalies of the Prince Albert Mountains and beneath the Polar Plateau show that this region was extensively effected by Jurassic tholeiitic magmatism; NE to NNE trending magnetic lineations within this pattern could reflect Cretaceous and/or Cenozoic faulting. The western and eastern edges of the Deep Freeze Range block, which flanks the Mesozoic Rennick Graben, are marked by two NW magnetic lineaments following the Priestley and Campbell Faults. The Campbell Fault is interpreted to be the reactivated Wilson thrust fault zone and is the site of a major isotopic discontinuity in the basement. To the east of the Campbell Fault, much higher amplitude magnetic anomalies reveal mafic-ultramafic intrusives associated with the alkaline Meander Intrusive Group (Eocene-Miocene). These intrusives are likely genetically linked to the highly uplifted Southern Cross Mountains block. The NW-SE trends crossing the previously recognized ENE trending Polar 3 Anomaly offshore of the Southern Cross Mountains are probably linked to Cenozoic reactivation of the Paleozoic Wilson-Bowers suture zone as proposed from recent seismic interpretations. The ENE trend of the anomaly may also be structural, and if so, it could reflect an inherited fault zone of the cratonal margin.

Anomalous concentrations of gold, silver, and other metals in the Mill Canyon area, Cortez quadrangle, Eureka and Lander Counties, Nevada

USGS Publications Warehouse

Elliott, James E.; Wells, John David

1968-01-01

The Mill Canyon area is in the eastern part of the Cortez window of the Roberts Mountains thrust belt in the Cortez quadrangle, north-central Nevada. Gold and silver ores have been mined from fissure veins in Jurassic quartz monzonite and in the bordering Wenban Limestone of Devonian age. Geochemical data show anomalies of gold, silver, lead, zinc, copper, arsenic, antimony, mercury, and tellurium. Geologic and geochemical studies indicate that a formation favorable for gold deposition, the Roberts Mountains Limestone of Silurian age, may be found at depth near the mouth of Mill Canyon.

Geomorphic evidence of Quaternary tectonics within an underlap fault zone of southern Apennines, Italy

NASA Astrophysics Data System (ADS)

Giano, Salvatore Ivo; Pescatore, Eva; Agosta, Fabrizio; Prosser, Giacomo

2018-02-01

A composite seismic source, the Irpinia - Agri Valley Fault zone, located in the axial sector of the fold-and-thrust belt of southern Apennines, Italy, is investigated. This composite source is made up of a series of nearly parallel, NW-striking normal fault segments which caused many historical earthquakes. Two of these fault segments, known as the San Gregorio Magno and Pergola-Melandro, and the fault-related mountain fronts, form a wedge-shaped, right-stepping, underlap fault zone. This work is aimed at documenting tectonic geomorphology and geology of this underlap fault zone. The goal is to decipher the evidence of surface topographic interaction between two bounding fault segments and their related mountain fronts. In particular, computation of geomorphic indices such as mountain front sinuosity (Smf), water divide sinuosity (Swd), asymmetry factor (AF), drainage basin elongation (Bs), relief ratio (Rh), Hypsometry (HI), normalized steepness (Ksn), and concavity (θ) is integrated with geomorphological analysis, the geological mapping, and structural analysis in order to assess the recent activity of the fault scarp sets recognized within the underlap zone. Results are consistent with the NW-striking faults as those showing the most recent tectonic activity, as also suggested by presence of related slope deposits younger than 38 ka. The results of this work therefore show how the integration of a multidisciplinary approach that combines geomorphology, morphometry, and structural analyses may be key to solving tectonic geomorphology issues in a complex, fold-and-thrust belt configuration.

Early Jurassic extensional inheritance in the Lurestan region of the Zagros fold-and-thrust belt, Iran.

NASA Astrophysics Data System (ADS)

Tavani, Stefano; Parente, Mariano; Vitale, Stefano; Puzone, Francesco; Erba, Elisabetta; Bottini, Cinzia; Morsalnejad, Davoud; Mazzoli, Stefano

2017-04-01

It has long been recognized that the tectonic architecture of the Zagros mountain belt was strongly controlled by inherited structures previously formed within the Arabian plate. These preexisting features span in age from the pre-Cambrian to the Mesozoic, showing different trends and deformation styles. Yet, these structures are currently not fully understood. This uncertainty is partly related with the paucity of exposures, which rarely allows a direct observation of these important deformation features. The Lurestan Province of Iran provides a remarkable exception, since it is one of the few places of the Zagros mountain belt where exposures of Triassic and Jurassic rocks are widespread. In this area we carried out structural observations on Mesozoic extensional structures developed at the southern margin of the Neo-Tethyan basin. Syn-sedimentary extensional faults are hosted within the Triassic-Cretaceous succession, being particularly abundant in the Jurassic portion of the stratigraphy. Early to Middle Jurassic syn-sedimentary faults are observed in different paleogeographic domains of the area, and their occurrence is coherent with the subsequent transition from shallow-water to deep-sea basin environments, observed in a wide portion of the area. Most of the thrusts exposed in the area may indeed be interpreted as reactivated Jurassic extensional faults, or as reverse faults whose nucleation was controlled by the location of preexisting normal faults, as a result of positive inversion during crustal shortening and mountain building.

Palinspastic reconstruction of southeastern California and southwestern Arizona for the middle Miocene

NASA Technical Reports Server (NTRS)

Richard, Stephen M.

1992-01-01

A paleogeographic reconstruction of southeastern California and southwestern Arizona at 10 Ma was made based on available geologic and geophysical data. Clockwise rotation of 39 deg was reconstructed in the eastern Transverse Ranges, consistent with paleomagnetic data from late Miocene volcanic rocks, and with slip estimates for left-lateral faults within the eastern Transverse Ranges and NW-trending right lateral faults in the Mojave Desert. This domain of rotated rocks is bounded by the Pinto Mountain fault on the north. In the absence of evidence for rotation of the San Bernardino Mountains or for significant right slip faults within the San Bernardino Mountains, the model requires that the late Miocene Pinto Mountain fault become a thrust fault gaining displacement to the west. The Squaw Peak thrust system of Meisling and Weldon may be a western continuation of this fault system. The Sheep Hole fault bounds the rotating domain on the east. East of this fault an array of NW-trending right slip faults and south-trending extensional transfer zones has produced a basin and range physiography while accumulating up to 14 km of right slip. This maximum is significantly less than the 37.5 km of right slip required in this region by a recent reconstruction of the central Mojave Desert. Geologic relations along the southern boundary of the rotating domain are poorly known, but this boundary is interpreted to involve a series of curved strike slip faults and non-coaxial extension, bounded on the southeast by the Mammoth Wash and related faults in the eastern Chocolate Mountains. Available constraints on timing suggest that Quaternary movement on the Pinto Mountain and nearby faults is unrelated to the rotation of the eastern Transverse Ranges, and was preceded by a hiatus during part of Pliocene time which followed the deformation producing the rotation. The reconstructed Clemens Well fault in the Orocopia Mountains, proposed as a major early Miocene strand of the San Andreas fault, projects eastward towards Arizona, where early Miocene rocks and structures are continuous across its trace. The model predicts a 14 deg clockwise rotation and 55 km extension along the present trace of the San Andreas fault during late Miocene and early Pliocene time. Palinspastic reconstructions of the San Andreas system based on this proposed reconstruction may be significantly modified from current models.

Influence of soil development on the geomorphic evolution of landscapes: An example from the Transverse Ranges of California

NASA Astrophysics Data System (ADS)

Eppes, M. C.; McFadden, L. D.; Matti, J.; Powell, R.

2002-03-01

Soil development can significantly influence the topographic evolution of a tectonically deforming mountain piedmont. Faults and folds associated with the North Frontal thrust system deform piedmont sediments of variable compositions along the north flank of the San Bernardino Mountains. The topographic expressions of folds with similar structural characteristics diverge appreciably, primarily as a function of differences in sediment composition and associated soil development. Soils with petrocalcic horizons in limestone- rich deposits are resistant to erosion, and anticlinal folds form prominent ridges. Folds forming in granite-derived deposits with argillic soil horizons are eroded and/or buried and are therefore topographically less pronounced. We propose that these landform contrasts can be explained by differences in soil-controlled hydrologic and erosion characteristics of deposits without calling upon changes in tectonic style along the mountain front.

Geologic map of the Ennis 30' x 60' quadrangle, Madison and Gallatin Counties, Montana

USGS Publications Warehouse

Kellogg, Karl S.; Williams, Van S.

1998-01-01

The Ennis 1:100,000 quadrangle lies within both the Laramide (Late Cretaceous to early Tertiary) foreland province of southwestern Montana and the northeastern margin of the middle to late Tertiary Basin and Range province. The oldest rocks in the quadrangle are Archean high-grade gneiss, and granitic to ultramafic intrusive rocks that are as old as about 3.0 Ga. The gneiss includes a supracrustal assemblage of quartz-feldspar gneiss, amphibolite, quartzite, and biotite schist and gneiss. The basement rocks are overlain by a platform sequence of sedimentary rocks as old as Cambrian Flathead Quartzite and as young as Upper Cretaceous Livingston Group sandstones, shales, and volcanic rocks. The Archean crystalline rocks crop out in the cores of large basement uplifts, most notably the 'Madison-Gravelly arch' that includes parts of the present Tobacco Root Mountains and the Gravelly, Madison, and Gallatin Ranges. These basement uplifts or blocks were thrust westward during the Laramide orogeny over rocks as young as Upper Cretaceous. The thrusts are now exposed in the quadrangle along the western flanks of the Gravelly and Madison Ranges (the Greenhorn thrust and the Hilgard fault system, respectively). Simultaneous with the west-directed thrusting, northwest-striking, northeast-side-up reverse faults formed a parallel set across southwestern Montana; the largest of these is the Spanish Peaks fault, which cuts prominently across the Ennis quadrangle. Beginning in late Eocene time, extensive volcanism of the Absorka Volcanic Supergroup covered large parts of the area; large remnants of the volcanic field remain in the eastern part of the quadrangle. The volcanism was concurrent with, and followed by, middle Tertiary extension. During this time, the axial zone of the 'Madison-Gravelly arch,' a large Laramide uplift, collapsed, forming the Madison Valley, structurally a complex down-to-the-east half graben. Basin deposits as thick as 4,500 m filled the graben. Pleistocene glaciers sculpted the high peaks of the mountain ranges and formed the present rugged topography.

Geologic map of the Ennis 30' x 60' quadrangle, Madison and Gallatin Counties, Montana, and Park County, Wyoming

USGS Publications Warehouse

Kellogg, Karl S.; Williams, Van S.

2000-01-01

The Ennis 1:100,000 quadrangle lies within both the Laramide (Late Cretaceous to early Tertiary) foreland province of southwestern Montana and the northeastern margin of the middle to late Tertiary Basin and Range province. The oldest rocks in the quadrangle are Archean high-grade gneiss, and granitic to ultramafic intrusive rocks that are as old as about 3.0 Ga. The gneiss includes a supracrustal assemblage of quartz-feldspar gneiss, amphibolite, quartzite, and biotite schist and gneiss. The basement rocks are overlain by a platform sequence of sedimentary rocks as old as Cambrian Flathead Quartzite and as young as Upper Cretaceous Livingston Group sandstones, shales, and volcanic rocks. The Archean crystalline rocks crop out in the cores of large basement uplifts, most notably the 'Madison-Gravelly arch' that includes parts of the present Tobacco Root Mountains and the Gravelly, Madison, and Gallatin Ranges. These basement uplifts or blocks were thrust westward during the Laramide orogeny over rocks as young as Upper Cretaceous. The thrusts are now exposed in the quadrangle along the western flanks of the Gravelly and Madison Ranges (the Greenhorn thrust and the Hilgard fault system, respectively). Simultaneous with the west-directed thrusting, northwest-striking, northeast-side-up reverse faults formed a parallel set across southwestern Montana; the largest of these is the Spanish Peaks fault, which cuts prominently across the Ennis quadrangle. Beginning in late Eocene time, extensive volcanism of the Absorka Volcanic Supergroup covered large parts of the area; large remnants of the volcanic field remain in the eastern part of the quadrangle. The volcanism was concurrent with, and followed by, middle Tertiary extension. During this time, the axial zone of the 'Madison-Gravelly arch,' a large Laramide uplift, collapsed, forming the Madison Valley, structurally a complex down-to-the-east half graben. Basin deposits as thick as 4,500 m filled the graben. Pleistocene glaciers sculpted the high peaks of the mountain ranges and formed the present rugged topography.

Geologic and geophysical maps of the Las Vegas 30' x 60' quadrangle, Clark and Nye counties, Nevada, and Inyo County, California

USGS Publications Warehouse

Page, William R.; Lundstrom, Scott C.; Harris, Anita G.; Langenheim, V.E.; Workman, Jeremiah B.; Mahan, Shannon; Paces, James B.; Dixon, Gary L.; Rowley, Peter D.; Burchfiel, B.C.; Bell, John W.; Smith, Eugene I.

2005-01-01

Las Vegas and Pahrump are two of the fastest growing cities in the US, and the shortage of water looms as among the greatest future problems for these cities. These new maps of the Las Vegas 30 x 60-minute quadrangle provide a geologic and geophysical framework and fundamental earth science database needed to address societal issues such as ground water supply and contamination, surface flood, landslide, and seismic hazards, and soil properties and their changing impact by and on urbanization. The mountain ranges surrounding Las Vegas and Pahrump consist of Mesozoic, Paleozoic and Proterozoic rocks. A majority of these rocks are Paleozoic carbonate rocks that are part of Nevada's carbonate rock aquifer province. The Spring Mountains represent a major recharge site in the province, where maximum altitude is 3,632 m (Charleston Peak) above sea level. Rocks in the Sheep and Las Vegas Ranges and Spring Mountains contain correlative, northeast-striking, southeast-verging thrust faults that are part of the Cretaceous, Sevier orogenic belt. These thrusts were offset during the Miocene by the Las Vegas Valley shear system (LVVSZ). We conducted new mapping in the Blue Diamond area, highlighting refined work on the Bird Spring thrust, newly studied ancient landslides, and gravity-slide blocks. We conducted new mapping in the Las Vegas Range and mapped previously unrecognized structures such as the Valley thrust and fold belt; recognition of these structures has led to a refined correlation of Mesozoic thrust faults across the LVVSZ. New contributions in the quadrangle also include a greatly refined stratigraphy of Paleozoic bedrock units based on conodont biostragraphy. We collected over 200 conodont samples in the quadrangle and established stratigraphic reference sections used to correlate units across the major Mesozoic thrust faults. Quaternary deposits cover about half of the map area and underlie most of the present urbanized area. Deposits consist of large coalescing alluvial fans that grade downslope to extensive areas of fine-grained sediment indicative of groundwater-discharge during the Pleistocene. In the central areas of Las Vegas and Pahrump valleys, Quaternary fault scarps associated with past ground-water discharge deposits suggest a genetic relationship. In collaboration with NBMG and University of Nevada, a variety of ages of gravelly alluvium are newly mapped using surficial characteristics and soil development, along with reassessment of previously published mapping during compilation. Reconnaissance geochronology (thermoluminescence and U-series) of eolian and authigenic components of surficial and buried soils and spring deposits is applied to test hypotheses of geomorphic and hydrologic response to climate change over the past 100 k.y.). The major structure in the Las Vegas quadrangle is the LVVSZ. Because the LVVSZ is concealed by thick basin-fill deposits of Quaternary and Tertiary age, it was characterized primarily based on geophysics. Likewise, the newly described State line fault system in Pahrump Valley has also been characterized by geophysics, where geophysically inferred structures correlate remarkably with surface structures defined by our new geologic mapping in the Mound Spring and Hidden Hills Ranch 7.5-minute quadrangles.

Late Archean greenstone tectonics: Evidence for thermal and thrust-loading lithospheric subsidence from stratigraphic sections in the Slave Province, Canada

NASA Technical Reports Server (NTRS)

Kidd, W. S. F.; Kusky, T. M.; Bradley, D. C.

1988-01-01

How late Archean tectonics could be seen to have operated in the Slave Province is illustrated. Lithospheric thinning and stretching, with the formation of rifted margins (to continental or island arc fragments), and lithospheric flexural loading of the kind familiar in arcs and mountain belts could be discerned.

Age and tectonic setting of Mesozoic metavolcanic and metasedimentary rocks, northern White Mountains, California

NASA Astrophysics Data System (ADS)

Hanson, R. Brooks; Saleeby, Jason B.; Fates, D. Gilbert

1987-11-01

Mesozoic metavolcanic and metasedimentary rocks in the northern White Mountains, eastern California and western Nevada, are separated from lower Paleozoic and Precambrian rocks by Jurassic and Cretaceous plutons. The large stratigraphic hiatus across the plutons is called the Barcroft structural break. Recent mapping and new U/Pb zircon ages of 154 +3/-1 Ma and 137 ±1 Ma. from an ash-flow tuff and a hypabyssal intrusion, respectively, indicate that part of the Mesozoic section and the Barcroft structural break are younger than the 160 165 Ma Barcroft Granodiorite, in contrast to previous interpretations. The Barcroft Granodiorite has been thrust westward over most of the Mesozoic section. It is everywhere in fault contact with overturned metasedimentary rocks on the west side of the range, rocks which were previously thought to be upright and the oldest part of the Mesozoic section. The McAfee Creek Granite, which has a 100 ±1 Ma U/Pb zircon age, postdates thrusting; therefore, the Barcroft structural break is primarily Early Cretaceous in age. *Present addresses: Hanson—Department of Mineral Sciences, Smithsonian Institution, Washington, D.C. 20560; Fates—Dames & Moore, 455 S. Figueroa Street, Suite 3504, Los Angeles, California 90074

Isotopic complexities and the age of the Delfonte volcanic rocks, eastern Mescal Range, southeastern California: Stratigraphic and tectonic implications

USGS Publications Warehouse

Fleck, R.J.; Mattinson, J.M.; Busby, C.J.; Carr, M.D.; Davis, G.A.; Burchfiel, B.C.

1994-01-01

Combined U-Pb zircon, Rb-Sr, 40Ar/39Ar laser-fusion, and conventional K-Ar geochronology establish a late Early Cretaceous age for the Delfonte volcanic rocks. U-Pb zircon analyses define a lower intercept age of 100.5 ± 2 Ma that is interpreted as the crystallization age of the Delfonte sequence. Argon studies document both xenocrystic contamination and postemplacement Ar loss. Rb-Sr results from mafic lavas at the base of the sequence demonstrate compositionally correlated variations in initial 87Sr/86Sr ratios (Sri) from 0.706 for basalts to 0.716 for andesitic compositions. This covariation indicates substantial mixing of subcontinental lithosphere with Proterozoic upper crust. Correlations between Rb/Sr and Sri may result not only in pseudoisochrons approaching the age of the crustal component, but also in reasonable but incorrect apparent ages approaching the true age.Ages obtained in this study require that at least some of the thrust faulting in the Mescal Range-Clark Mountain portion of the foreland fold-and-thrust belt occurred later than ca. 100 Ma and was broadly contemporaneous with emplacement of the Keystone thrust plate in the Spring Mountains to the northeast. Comparison of the age and Rb-Sr systematics of ash-flow tuff boulders in the synorogenic Lavinia Wash sequence near Goodsprings, Nevada, with those of the Delfonte volcanic rocks supports a Delfonte source for the boulders. The 99 Ma age of the Lavinia Wash sequence is nearly identical to the Delfonte age, requiring rapid erosion, transport, and deposition following Delfonte volcanism.

Relation between relief and crustal structure in the Cantabrian Mountains (Spain) using DEM-GIS analysis

NASA Astrophysics Data System (ADS)

Llana-Fúnez, Sergio; Rodríguez-Rodríguez, Laura; Ballesteros, Daniel; María Díaz-Díaz, Luis; Valenzuela, Pablo; López-Fernández, Carlos; José Domínguez-Cuesta, María; Meléndez, Mónica; Jiménez-Sánchez, Montserrat; Fernández-Viejo, Gabriela

2017-04-01

The Cantabrian Mountains show a linear E-W trend parallel to the northern coast of Iberia peninsula, from the Pyrenees to Galicia, where it looses its trend and linearity. The western end of the linear segment of the orogen coincides with a change in the style of structures, accommodating the N-S shortening during the convergence between Europe and Iberia plates. We study the relief of the 230 km-long segment of the linear range between the Cantabria and Galicia re- gions, up to 2,650 m altitude. The bulk trend of the orogeny is controlled by the orientation of alpine thrusts that accommodate the shortening in relation to plate convergence. The Alpine Orogeny produced crustal thickening and the present day topography. Crustal thickness varies from 30 km in Eastern Cantabrian Mountains to 45-55 km at the Middle part of these mountains. The collision between European and African plates localized in northern Iberia from the Eocene to Oligocene and later migrated to southern Iberia during the Miocene. No major tectonic convergence was accommodated in the Cantabrians Mountains since the Oligocene, entering the orogen an erosional phase since then. The GIS-analysis present here, using 5 and 25 m-resolution DEMs by the Spanish National Geographical Institute, aims to identify the major features and to characterize the overall relief of the Cantabrians Mountains. In our preliminary approach, we present swath profiles, major river basins, watershed, longitudinal profiles of major rivers and hypsometric curves from selected areas that cover the studied orogen segment. Major tectonic structures control the location and orientation of the main watershed of the mountain range, but also the orientation of some local watersheds, e.g. associated to the Llanera thrust or the Ventaniella (strike-slip) fault. An unexpected result is that the average altitude along the water divide is 1,500 m, regardless of the large differences in crustal thickness along the study area. Most longitudinal river profiles running south to north lack knick points in relation to relief forming tectonic structures, indicative of the predominance of fluvial erosional system postdating tectonics. An emerged coastal wave-cut platform dipping gently towards the West, a slight increase in maximum mountain altitude to the east and slight increase in river incision also towards the East may indicate that a gradient in erosion and in up-lifting exists increasing from West to East. This is consistent with an overall increase of crustal thickness along this direction.

Seismotectonics of the Pamir

NASA Astrophysics Data System (ADS)

Schurr, Bernd; Sippl, Christian; Yuan, Xiaohui; Mechie, James; Lothar, Ratschbacher

2013-04-01

The Pamir Mountains form a complex orographic node north of the western Himalayan Syntaxis. Due to the Pamir's remote location, crustal tectonics of the region is not well studied. We report new data on distribution and kinematics of crustal earthquakes in the Pamir and its surroundings. Our data set stems from a deployment of seismometers between 2008-2010 that covered the SW Tien Shan, Pamir and Tajik basin. We detected and carefully relocated several thousand crustal earthquakes that are confined to the uppermost 20 km of the crust and thereby clearly separated from Pamir's unique intermediate depth seismicity. For the larger earthquakes (M<3) we use both full waveform inversion and first motion polarities to determine source mechanisms. A string of earthquakes outlines the thrust system along the northern Pamir's perimeter. In the east, where the Pamir collides with the Tien Shan, the M6.7 Nura earthquake activated several faults. Whereas the main shock shows almost pure reverse faulting on a south dipping thrust, many aftershocks also show sinistral strike-slip faulting along a NE striking lineamnet. In the centre, where the Pamir overthrusts the intramontane Alai valley, micro-seismicity recedes southward from the Frontal and Trans Alai thrust systems. The largest of these earthquakes show mostly strike-slip mechanisms. Further west, where the Pamir thrust system bends southward, earthquakes show thrust mechanisms again with strikes following the oroclinal structures. Inside the Pamir a NE striking lineament runs from the eastern end of Lake Sarez across Lake Kara Kul to the Pamir thrust system. Source mechanisms along the lineament are sinistral strike slip and transtensional. This lineament approximately separates the deeply incised western Pamir, which shows significant seismic deformation, from the relatively aseismic eastern Pamir. In the western Pamir earthquakes cluster along approximately the Vanch valley and near Lake Sarez. Diffuse seismicity is also visible beneath the SW Pamir's basement domes. Source mechanisms exhibit mostly sinistral strike slip faulting on NE striking or conjugate planes indicating north-south compression and east-west extension. At the Pamir's western margin, where the mountains merge into the Tajik basin's fold and thrust belt, we observe numerous earthquakes with mechanisms exhibiting EW slip on subhorizontal planes. We interpret this as movement along the Jurassic evaporite decollement that detaches the sedimentary section from the basement. Our data indicate that in the western Pamir NS compression is accommodated by westward escape, i.e. the western Pamir is pushed into the Tajik depression ontop of a weak evaporite detachment. This is in accordance with the observed GPS displacement vectors rotating anticlockwise from NS to EW when traversing from the eastern Pamir into the Tajik depression.

Stable isotopic evidence for fluid flow and fluid/rock interaction during thrust faulting in Pumpkin Valley shale and Rome Formation, east Tennessee

DOE Office of Scientific and Technical Information (OSTI.GOV)

Butler, B.K.; Haase, C.S.

1989-08-01

The Pumpkin Valley Shale and the underlying Rome Formation form the lower portions of the Copper Creek and White Oak Mountain thrust sheets in east Tennessee. The Pumpkin Valley Shale consists of shale and mudstone with subordinate amounts of interbedded siltstone. The Rome Formation is composed predominantly of sandstone with interbedded shale and siltstone toward the base of the formation. The percentage of illite increases from 20% to over 80% of the bulk clay mineralogy toward the base of the section. Porosity is occluded by quartz, phyllosilicate, and calcite cements. Both formations contain calcite-filled and, less commonly, quartz-filled Alleghenian fracturesmore » and joints.« less

Seismicity of the Earth 1900–2010 Himalaya and vicinity

USGS Publications Warehouse

Turner, Bethan; Jenkins, Jennifer; Turner, Rebecca; Parker, Amy; Sinclair, Alison; Davies, Sian; Hayes, Gavin P.; Villaseñor, Antonio; Dart, Rirchard L.; Tarr, Arthur C.; Furlong, Kevin P.; Benz, Harley M.

2013-01-01

Seismicity in the Himalaya region predominantly results from the collision of the India and Eurasia continental plates, which are converging at a relative rate of 40–50 mm/yr. Northward underthrusting of India beneath Eurasia generates numerous earthquakes and consequently makes this area one of the most seismically hazardous regions on Earth. The surface expression of the plate boundary is marked by the foothills of the north-south trending Sulaiman Range in the west, the Indo-Burmese Arc in the east, and the east-west trending Himalaya Front in the north of India. Along the western margin of the India plate, relative motions between India and Eurasia are accommodated by strike-slip, reverse, and oblique-slip faulting resulting in the complex Sulaiman Range fold and thrust belt, and the major translational Chaman Fault in Afghanistan. Beneath the Pamir‒Hindu Kush Mountains of northern Afghanistan, earthquakes occur to depths as great as 200 km as a result of remnant lithospheric subduction. Further north again, the Tian Shan is a seismically active intra-continental mountain belt defined by a series of east-west trending thrust faults thought to be related to the broad footprint of the India-Eurasia collision. Tectonics in northern India are dominated by motion along the Main Frontal Thrust and associated thrust faults of the India-Eurasia plate boundary, which have resulted in a series of large and devastating earthquakes in (and prior to) the 20th century. The Tibetan Plateau to the north of the main plate boundary is a broad region of uplift associated with the India-Eurasia collision, and is cut by a series of generally east-west trending strike-slip faults. These include the Kunlun, Haiyuan, and the Altyn Tagh faults, all of which are left-lateral structures, and the Kara-Koram right-lateral fault. Throughout the plateau, thrust faults accommodate the north-south compressional component of crustal shortening associated with the ongoing collision of India and Eurasia, while strike-slip and normal faults accommodate east-west extension. To the east, The Longmen Shan thrust belt marks the eastern margin of the Tibetan Plateau separating the complex tectonics of the plateau region from the relatively undeformed Sichuan Basin. Further south, the left-lateral Xiangshuihe-Xiaojiiang, right-lateral Red River and right-lateral Sagaing strike-slip fault systems accommodate deformation along the eastern margin of the India plate. Deep earthquakes have also occurred in the Indo-Burmese Arc region, thought to be an expression of eastward-directed subduction of the India plate, though whether subduction is ongoing is still debated.

Mountain building on Io driven by deep faulting

USGS Publications Warehouse

Bland, Michael T.; McKinnon, William B

2016-01-01

Jupiter’s volcanic moon Io possesses some of the highest relief in the Solar System: massive, isolated mountain blocks that tower up to 17 km above the surrounding plains. These mountains are likely to result from pervasive compressive stresses induced by subsidence of the surface beneath the near-continual emplacement of volcanic material. The stress state that results from subsidence and warming of Io’s lithosphere has been investigated in detail1, 2, 3, 4; however, the mechanism of orogenesis itself and its effect on regional tectonism and volcanism has not been firmly established. Here we present viscoelastic–plastic finite element simulations demonstrating that Io’s mountains form along deep-seated thrust faults that initiate at the base of the lithosphere and propagate upward. We show that faulting fundamentally alters the stress state of Io’s lithosphere by relieving the large volcanism-induced subsidence stresses. Notably, in the upper portion of the lithosphere, stresses become tensile (near-zero differential stress). A number of processes are therefore altered post-faulting, including magma transport through the lithosphere, interactions with tidal stresses and potentially the localization of mountain formation by thermoelastic stresses. We conclude that Io’s mountains form by a unique orogenic mechanism, compared with tectonic processes operating elsewhere in the Solar System.

Paleozoic and mesozoic evolution of East-Central California

USGS Publications Warehouse

Stevens, C.H.; Stone, P.; Dunne, G.C.; Greene, D.C.; Walker, J.D.; Swanson, B.J.

1997-01-01

East-central California, which encompasses an area located on the westernmost part of sialic North America, contains a well-preserved record of Paleozoic and Mesozoic tectonic events that reflect the evolving nature of the Cordilleran plate margin to the west. After the plate margin was formed by continental rifting in the Neoproterozoic, sediments comprising the Cordilleran miogeocline began to accumulate on the subsiding passive margin. In east-central California, sedimentation did not keep pace with subsidence, resulting in backstepping of a series of successive carbonate platforms throughout the early and middle Paleozoic. This phase of miogeoclinal development was brought to a close by the Late Devonian-Early Mississippian Antler orogeny, during the final phase of which oceanic rocks were emplaced onto the continental margin. Subsequent Late Mississippian-Pennsylvanian faulting and apparent reorientation of the carbonate platform margin are interpreted to have been associated with truncation of the continental plate on a sinistral transform fault zone. In the Early Permian, contractional deformation in east-central California led to the development of a narrow, uplifted thrust belt flanked by marine basins in which thick sequences of deep-water strata accumulated. A second episode of contractional deformation in late Early Permian to earliest Triassic time widened and further uplifted the thrust belt and produced the recently identified Inyo Crest thrust, which here is correlated with the regionally significant Last Chance thrust. In the Late Permian, about the time of the second contractional episode, extensional faulting created shallow sedimentary basins in the southern Inyo Mountains. In the El Paso Mountains to the south, deformation and plutonism record the onset of subduction and arc magmatism in late Early Permian to earliest Triassic time along this part of the margin. Tectonism had ceased in most of east-central California by middle to late Early Triassic time, and marine sediment deposited on the subsiding continental shelf overlapped the previously deformed Permian rocks. Renewed contractional deformation, probably in the Middle Triassic, is interpreted to be associated with emplacement of the Golconda allochthon onto the margin of the continent. This event, which is identified with certainty in the Sierra Nevada, also may have significantly affected rocks in the White and Inyo Mountains to the east. Subduction and arc magmatism that created most of the Sierra Nevada batholith began in the Late Triassic and lasted through the remainder of the Mesozoic. During this time, the East Sierran thrust system (ESTS) developed as a narrow zone of intense, predominantly E-vergent contractional deformation along the eastern margin of the growing batholith. Activity on the ESTS took place over an extended part of Mesozoic time, both before and after intrusion of voluminous Middle Jurassic plutons, and is interpreted to have been mechanically linked to emplacement of the batholith. Deformation on the ESTS and magmatism in the Sierra Nevada both ended prior to the close of the Cretaceous.

Structural styles of the Guess Creek fault block beneath the Great Smoky thrust sheet, Blount County, Tennessee

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carter, M.W.; Davidson, G.L.; Heller, J.A.

1993-03-01

A road cut along US 321 N, approximately 1 km NW of Walland, TN, exposes a previously unexposed complexly deformed section of Middle Ordovician clastic wedge [Chickamauga Group, Sevier Shale] sedimentary rocks. It provides an excellent opportunity to analyze both the lithologic assemblages and complex folding and faulting beneath the Great Smoky thrust sheet. Arkosic quartzite of the Lower Cambrian Cochran Conglomerate [Chilhowee Group], has been thrust over weaker Sevier Shale in the hanging wall of the Guess Creek fault. Regionally, the Great Smoky fault separates metamorphosed Precambrian to Lower Cambrian clastic shelf, slope, and rift facies rocks of themore » western Blue Ridge from Cambro-Ordovician carbonate shelf and orogenic wedge deposits of the foreland fold and thrust belt. West of the Great Smoky fault, the Guess Creek fault has been interpreted to floor duplexed Cambro-Ordovician rocks exposed in windows beneath the Great Smoky thrust sheet in the vicinity of the Great Smoky Mountains National Park. The Sevier Shale here consists of variably cleaved shale, siltstone, sandstone, and conglomerate. It exhibits a variety of fold styles throughout the exposure, ranging from predominantly noncylindrical tight folds to broad, open structures. A weak axial-planar pencil cleavage is developed in the Middle Ordovician shale and siltstone, along with a secondary cleavage that transects the axial surfaces of the folds. Minor thrust faults within the Sevier Shale appear to have formed by propagation through tightened fold hinges or bedding-parallel slip. The fold pattern observed in the roadcut appears to be partly the result of movement along a tear fault that broke both the hanging wall and footwall of the Great Smoky thrust sheet after emplacement. Slickenline orientations along minor thrust surfaces in the Cochran Conglomerate indicate eastward-directed, oblique-slip movement of the tear fault.« less

Crustal structure of Wrangellia and adjacent terranes inferred from geophysical studies along a transect through the northern Talkeetna Mountains

USGS Publications Warehouse

Glen, J.M.G.; Schmidt, J.; Pellerin, L.; McPhee, D.K.; O'Neill, J. M.

2007-01-01

Recent investigations of the Talkeetna Mountains in south-central Alaska were undertaken to study the region's framework geophysics and to reinterpret structures and crustal composition. Potential field (gravity and magnetic) and magnetotelluric (MT) data were collected along northwest-trending profiles as part of the U.S. Geological Survey's Talkeetna Mountains transect project. The Talkeetna Mountains transect area comprises eight 1:63,360 quadrangles (???9500 km2) in the Healy and Talkeetna Mountains 1?? ?? 3?? sheets that span four major lithostratigraphic terranes (Glen et al., this volume) including the Wrangellia and Peninsular terranes and two Mesozoic overlap assemblages inboard (northwest) of Wrangellia. These data were used here to develop 21/2-dimensional models for the three profiles. Modeling results reveal prominent gravity, magnetic, and MT gradients (???3.25 mGal/ km, ???100nT/km, ???300 ohm-m/km) corresponding to the Talkeetna Suture Zone-a first-order crustal discontinuity in the deep crust that juxtaposes rocks with strongly contrasting rock properties. This discontinuity corresponds with the suture between relatively dense magnetic crust of Wrangellia (likely of oceanic composition) and relatively less dense transitional crust underlying Jurassic to Cretaceous flysch basins developed between Wrangellia and North America. Some area of the oceanic crust beneath Wrangellia may also have been underplated by mafic material during early to mid-Tertiary volcanism. The prominent crustal break underlies the Fog Lakes basin approximately where theTalkeetna thrust faultwaspreviouslymappedas a surface feature. Potential fieldand MT models, however, indicate that the Talkeetna Suture Zone crustal break along the transect is a deep (2-8 km), steeply west-dipping structure-not a shallow east-dipping Alpine nappe-like thrust. Indeed, most of the crustal breaks in the area appear to be steep in the geophysical data, which is consistent with regional geologic mapping that indicates that most of the faults are steep normal, reverse, strike-slip, or oblique-slip faults. Mapping further indicates that many of these features, which likely formed during Jurassic and Cretaceous time, such as the Talkeetna Suture Zone have reactivated inTertiary time (O'Neill et al., 2005). Copyright ?? 2007 The Geological Society of America.

Numerical modeling of mountain formation on Io

NASA Astrophysics Data System (ADS)

Turtle, E. P.; Jaeger, W. L.; McEwen, A. S.; Keszthelyi, L.

2000-10-01

Io has ~ 100 mountains [1] that, although often associated with patera [2], do not appear to be volcanic structures. The mountains are up to 16 km high [3] and are generally isolated from each other. We have performed finite-element simulations of the formation of these mountains, investigating several mountain building scenarios: (1) a volcanic construct due to heterogeneous resurfacing on a coherent, homogeneous lithosphere; (2) a volcanic construct on a faulted, homogeneous lithosphere; (3) a volcanic construct on a faulted, homogeneous lithosphere under compression induced by subsidence due to Io's high resurfacing rate; (4) a faulted, homogeneous lithosphere under subsidence-induced compression; (5) a faulted, heterogeneous lithosphere under subsidence-induced compression; and (6) a mantle upwelling beneath a coherent, homogeneous lithosphere under subsidence-induced compression. The models of volcanic constructs do not produce mountains similar to those observed on Io. Neither do those of pervasively faulted lithospheres under compression; these predict a series of tilted lithospheric blocks or plateaus, as opposed to the isolated structures that are observed. Our models show that rising mantle material impinging on the base of the lithosphere can focus the compressional stresses to localize thrust faulting and mountain building. Such faults could also provide conduits along which magma could reach the surface as is observed near several mountains. [1] Carr et al., Icarus 135, pp. 146-165, 1998. [2] McEwen et al., Science 288, pp. 1193-1198, 2000. [3] Schenk and Bulmer, Science 279, pp. 1514-1517, 1998.

Tectonic controls on large landslide complex: Williams Fork Mountains near Dillon, Colorado

USGS Publications Warehouse

Kellogg, K.S.

2001-01-01

An extensive (~ 25 km2) landslide complex covers a large area on the west side of the Williams Fork Mountains in central Colorado. The complex is deeply weathered and incised, and in most places geomorphic evidence of sliding (breakaways, hummocky topography, transverse ridges, and lobate distal zones) are no longer visible, indicating that the main mass of the slide has long been inactive. However, localized Holocene reactivation of the landslide deposits is common above the timberline (at about 3300 m) and locally at lower elevations. Clasts within the complex, as long as several tens of meters, are entirely of crystalline basement (Proterozoic gneiss and granitic rocks) from the hanging wall of the Laramide (Late Cretaceous to Early Tertiary), west-directed Williams Range thrust, which forms the western structural boundary of the Colorado Front Range. Late Cretaceous shale and sandstone compose most footwall rocks. The crystalline hanging-wall rocks are pervasively fractured or shattered, and alteration to clay minerals is locally well developed. Sackung structures (trenches or small-scale grabens and upslope-facing scarps) are common near the rounded crest of the range, suggesting gravitational spreading of the fractured rocks and oversteepening of the mountain flanks. Late Tertiary and Quaternary incision of the Blue River Valley, just west of the Williams Fork Mountains, contributed to the oversteepening. Major landslide movement is suspected during periods of deglaciation when abundant meltwater increased pore-water pressure in bedrock fractures. A fault-flexure model for the development of the widespread fracturing and weakening of the Proterozoic basement proposes that the surface of the Williams Range thrust contains a concave-downward flexure, the axis of which coincides approximately with the contact in the footwall between Proterozoic basement and mostly Cretaceous rocks. Movement of brittle, hanging-wall rocks through the flexure during Laramide deformation pervasively fractured the hanging-wall rocks. ?? 2001 Elsevier Science B.V. All rights reserved.

The tectonometamorphic evolution of the Apuseni Mountains (Romania): Geodynamic constraints for the evolution of the Alps-Carpathians-Dinaride system of orogens

NASA Astrophysics Data System (ADS)

Reiser, Martin; Schuster, Ralf; Fügenschuh, Bernhard

2015-04-01

New structural, thermobarometric and geochronological data allow integrating kinematics, timing and intensity of tectonic phases into a geodynamic model of the Apuseni Mountain, which provides new constraints for the evolution of the Alps-Carpathians-Dinaride system of orogens. Strong differences in terms of deformation directions between Early and Late Cretaceous events provide new constraints on the regional geodynamic evolution during the Cretaceous. Geochronological and structural data evidence a Late Jurassic emplacement of the South Apuseni Ophiolites on top of the Biharia Nappe System (Dacia Mega-Unit), situated in an external position at the European margin. Following the emplacement of the ophiolites, three compressive deformation phases affected the Apuseni Mountains during Alpine orogeny: a) NE-directed in-sequence nappe stacking and regional metamorphic overprinting under amphibolite-facies conditions during the Early Cretaceous ("Austrian Phase"), b) NW-directed thrusting and folding, associated with greenschist-facies overprinting, during the early Late Cretaceous ("Turonian Phase") and c) E-W internal folding together with brittle thrusting during the latest Cretaceous ("Laramian Phase"). Major tectonic unroofing and exhumation at the transition from Early to Late Cretaceous times is documented through new Sm-Nd Grt, Ar-Ar Ms and Rb-Sr Bt ages from the study area and resulted in a complex thermal structure with strong lateral and vertical thermal gradients. Nappe stacking and medium-grade metamorphic overprinting during the Early Cretaceous exhibits striking parallels between the evolution of the Tisza-Dacia Mega-Units and the Austroalpine Nappes (ALCAPA Mega-Unit) and evidences a close connection. However, Late Cretaceous tectonic events in the study area exhibit strong similarities with the Dinarides. Thus, the Apuseni Mountains represent the "missing link" between the Early Cretaceous Meliata subduction (associated with obduction of ophiolites) and the Neotethys subduction during Late Cretaceous times.

The western limits of the Seattle fault zone and its interaction with the Olympic Peninsula, Washington

USGS Publications Warehouse

A.P. Lamb,; L.M. Liberty,; Blakely, Richard J.; Pratt, Thomas L.; Sherrod, B.L.; Van Wijk, K.

2012-01-01

We present evidence that the Seattle fault zone of Washington State extends to the west edge of the Puget Lowland and is kinemati-cally linked to active faults that border the Olympic Massif, including the Saddle Moun-tain deformation zone. Newly acquired high-resolution seismic reflection and marine magnetic data suggest that the Seattle fault zone extends west beyond the Seattle Basin to form a >100-km-long active fault zone. We provide evidence for a strain transfer zone, expressed as a broad set of faults and folds connecting the Seattle and Saddle Mountain deformation zones near Hood Canal. This connection provides an explanation for the apparent synchroneity of M7 earthquakes on the two fault systems ~1100 yr ago. We redefi ne the boundary of the Tacoma Basin to include the previously termed Dewatto basin and show that the Tacoma fault, the southern part of which is a backthrust of the Seattle fault zone, links with a previously unidentifi ed fault along the western margin of the Seattle uplift. We model this north-south fault, termed the Dewatto fault, along the western margin of the Seattle uplift as a low-angle thrust that initiated with exhu-mation of the Olympic Massif and today accommodates north-directed motion. The Tacoma and Dewatto faults likely control both the southern and western boundaries of the Seattle uplift. The inferred strain trans-fer zone linking the Seattle fault zone and Saddle Mountain deformation zone defi nes the northern margin of the Tacoma Basin, and the Saddle Mountain deformation zone forms the northwestern boundary of the Tacoma Basin. Our observations and model suggest that the western portions of the Seattle fault zone and Tacoma fault are com-plex, require temporal variations in principal strain directions, and cannot be modeled as a simple thrust and/or backthrust system.

Seismicity of the Earth 1900–2010 Middle East and vicinity

USGS Publications Warehouse

Jenkins, Jennifer; Turner, Bethan; Turner, Rebecca; Hayes, Gavin P.; Davies, Sian; Dart, Richard L.; Tarr, Arthur C.; Villaseñor, Antonio; Benz, Harley M.

2013-01-01

No fewer than four major tectonic plates (Arabia, Eurasia, India, and Africa) and one smaller tectonic block (Anatolia) are responsible for seismicity and tectonics in the Middle East and surrounding region. Geologic development of the region is a consequence of a number of first-order plate tectonic processes that include subduction, large-scale transform faulting, compressional mountain building, and crustal extension. In the east, tectonics are dominated by the collision of the India plate with Eurasia, driving the uplift of the Himalaya, Karakorum, Pamir and Hindu Kush mountain ranges. Beneath the Pamir‒Hindu Kush Mountains of northern Afghanistan, earthquakes occur to depths as great as 200 km as a result of remnant lithospheric subduction. Along the western margin of the India plate, relative motions between India and Eurasia are accommodated by strike-slip, reverse, and oblique-slip faulting, resulting in the complex Sulaiman Range fold and thrust belt, and the major translational Chaman Fault in Afghanistan. Off the south coasts of Pakistan and Iran, the Makran trench is the surface expression of active subduction of the Arabia plate beneath Eurasia. Northwest of this subduction zone, collision between the two plates forms the approximately 1,500-km-long fold and thrust belts of the Zagros Mountains, which cross the whole of western Iran and extend into northeastern Iraq. Tectonics in the eastern Mediterranean region are dominated by complex interactions between the Africa, Arabia, and Eurasia plates, and the Anatolia block. Dominant structures in this region include: the Red Sea Rift, the spreading center between the Africa and Arabia plates; the Dead Sea Transform, a major strike-slip fault, also accommodating Africa-Arabia relative motions; the North Anatolia Fault, a right-lateral strike-slip structure in northern Turkey accommodating much of the translational motion of the Anatolia block westwards with respect to Eurasia and Africa; and the Cyprian Arc, a convergent boundary between the Africa plate to the south, and Anatolia Block to the north.

Map of normal faults and extensional folds in the Tendoy Mountains and Beaverhead Range, Southwest Montana and eastern Idaho

USGS Publications Warehouse

Janecke, S.U.; Blankenau, J.J.; VanDenburg, C.J.; VanGosen, B.S.

2001-01-01

Compilation of a 1:100,000-scale map of normal faults and extensional folds in southwest Montana and adjacent Idaho reveals a complex history of normal faulting that spanned at least the last 50 m.y. and involved six or more generations of normal faults. The map is based on both published and unpublished mapping and shows normal faults and extensional folds between the valley of the Red Rock River of southwest Montana and the Lemhi and Birch Creek valleys of eastern Idaho between latitudes 45°05' N. and 44°15' N. in the Tendoy and Beaverhead Mountains. Some of the unpublished mapping has been compiled in Lonn and others (2000). Many traces of the normal faults parallel the generally northwest to north-northwest structural grain of the preexisting Sevier fold and thrust belt and dip west-southwest, but northeastand east-striking normal faults are also prominent. Northeaststriking normal faults are subparallel to the traces of southeast-directed thrusts that shortened the foreland during the Laramide orogeny. It is unlikely that the northeast-striking normal faults reactivated fabrics in the underlying Precambrian basement, as has been documented elsewhere in southwestern Montana (Schmidt and others, 1984), because exposures of basement rocks in the map area exhibit north-northwest- to northwest-striking deformational fabrics (Lowell, 1965; M’Gonigle, 1993, 1994; M’Gonigle and Hait, 1997; M’Gonigle and others, 1991). The largest normal faults in the area are southwest-dipping normal faults that locally reactivate thrust faults (fig. 1). Normal faulting began before middle Eocene Challis volcanism and continues today. The extension direction flipped by about 90° four times.

Low-temperature thermochronology of the Laramide Ranges and eastward translation of shortening in the Sevier Belt, Wyoming, Utah and Montana

NASA Astrophysics Data System (ADS)

Peyton, Sara Lynn

This dissertation contains two studies that use very different techniques to investigate the Mesozoic and Cenozoic tectonics of the western USA. The first study investigates shortening in the Sevier thrust belt of northeast Utah and southwest Wyoming using cross sections and seismic reflection data. The second study investigates the low-temperature thermochronology of the Laramide Ranges using apatite (U-Th)/He dating. We used cross sections and seismic reflection data to investigate bed length discrepancies within the hanging wall of the Absaroka thrust in the Sevier thrust belt of northeast Utah and southwest Wyoming. Restoration of cross sections suggests that there was ˜8-14 km of pre-Absaroka-thrust shortening above the Jurassic Preuss salt detachment, but not below it, in the hanging wall of the Absaroka thrust. Reflection seismic data over the hanging wall of the Crawford thrust show that the Crawford thrust is not offset along the Preuss salt detachment, indicating that the additional shortening on the Absaroka plate was transferred east before main movement on the Crawford thrust. Although early displacement on the Crawford thrust cannot be ruled out as the cause of the extra shortening, surface and subsurface geology suggests slip from the western thrust system (Willard and Lost Creek thrusts) was transferred several tens of kilometers east along the Jurassic Preuss salt detachment between ˜102-90 Ma, to the future location of the Absaroka thrust hanging wall. The lack of deformation of the Crawford thrust on the seismic data, along with shortening and extension estimates from cross sections, also indicate that the magnitude of Paleocene and post-early Eocene shortening on the Medicine Butte thrust was essentially offset by subsequent extension on the middle Eocene to late Oligocene Almy-Acocks normal-fault system. For the second study in this dissertation, we dated 91 borehole and surface samples from Laramide-age, basement-cored uplifts of the Rocky Mountain foreland (Wind River, Beartooth, Bighorn and Laramie Ranges) and the Uncompahgre Uplift using the apatite (U-Th)/He system. Apatite (U-Th)/He ages generally decrease with increasing subsurface depth (decreasing elevation) and most samples show age dispersion ranging from tens to hundreds of Myr. Additionally, several samples show correlations between apatite (U-Th)/He age and effective U concentration (eU = [U] + 0.235[Th]) of the crystal, indicating that radiation damage has affected He diffusivity, and hence (U-Th)/ He age. Many surface and near-surface samples have apatite (U-Th)/He ages that are older than corresponding apatite fission-track ages. Forward modeling of Laramide-type thermal histories using a radiation damage diffusion model showed that (U-Th)/He ages may be widely dispersed, and may be older than corresponding apatite fission-track ages within a fossil He partial retention zone. Most of our samples, however, do not show the correlation between (U-Th)/He age and eU predicted by radiation damage diffusion models. We investigated the influence of both grain size and eU content and show that the effects of grain size can obscure (U-Th)/ He age-eU correlations and, similarly, the effect of eU variation can obscure (U-Th)/ He age-grain size correlations. (U-Th)/He ages that are older than fission-track ages from high peaks in the Wind River Range, and from some samples from the Beartooth Range, are most likely the result of He implantation from high eU phases. Best-fit thermal histories from the inversion of age-eU pairs were extrapolated to other elevations to create model age-elevation profiles for a range of eU concentrations. These model profiles approximate our real data. Inverse modeling of (U-Th)/He age data suggests that rapid exhumation within the Laramide province likely began earlier in the Bighorn Mountains (before ˜71 Ma) than the Beartooth Range (before ˜58 Ma), and that the borehole at the northern end of the Laramie Range penetrated a fault sliver at depth.

Evidence for Crustal-Scale Imbrication and non-Equilibrium Topography in the Southern Central Range, Taiwan

NASA Astrophysics Data System (ADS)

Byrne, T. B.; Huang, C.; Ouimet, W. B.; Rau, R.; Hsieh, M.; Lee, Y.

2011-12-01

We integrate a suite of new and recently re-interpreted profiles of the 3-D crustal velocity structure from the southern Central Range of Taiwan with geomorphic data from the range and propose that the topography is supported by a crustal-scale, west-verging thrust. The extent and geometry of the thrust is indicated by contours of P-wave velocity that are progressively overturned from south to north, placing high Vp rocks above low Vp rocks. The interpreted thrust dips gently east (15-20 degrees) and carries pre-Tertiary metamorphic rocks and Eocene to Miocene rocks with a well-developed slaty cleavage in its hanging wall. The thrust is interpreted to cut up section to the west and link with the basal detachment of the fold-and-thrust belt. Leveling data1 along the South Cross-Island Highway also suggest that the thrust is active. Along-strike profiles suggest that the thrust is propagating southward, consistent with a progressive decrease in mean elevation and an increase in reset apatite fission track ages from north to south. The hanging wall of the propagating thrust also correlates with anomalous areas of low topographic relief that straddle the crest of the southern part of the range. The areas of low relief are fringed by stream channels with relatively high stream gradient indexes and do not appear related to weaker rock types, glacial erosion, or lower rock uplift rates along the range crest. We propose that the surfaces represent relict topography that formed prior to a recent acceleration in rock uplift rate, consistent with the presence of a propagating, crustal-scale thrust in the subsurface. Taken together, these results raise questions about the notion of steady state topography and critically tapered wedges in Taiwan. 1) Ching, Kuo-En, Hsieh, M.-L., Johnson, K. M., Chen, K-H., Rau, R.-J., Yang M., Modern vertical deformation rates and mountain building in Taiwan from precise leveling and continuous GPS observations, 2000-2008, in press, JGR.

New Structural Interpretation of the Central Confusion Range, Western Utah, Based On Balanced Cross Sections

NASA Astrophysics Data System (ADS)

Yezerski, D.; Greene, D. C.

2009-12-01

The Confusion Range is a topographically low mountain range in the Basin and Range of west-central Utah, located east of and in the hanging wall of the Snake Range core complex. Previous workers have used a gravity sliding model to interpret the Confusion Range as a large structural trough or synclinorium (e.g. Hose, 1977). Based on existing mapping (Hose, 1965; Hintze, 1974) and new field data, we use balanced and restored cross sections to reinterpret the structure of the Confusion Range as an east-vergent fold-and-thrust belt formed during the Sevier Orogeny. The Confusion Range consists of Cambro-Ordovician through Triassic strata, with predominantly thick-bedded, competent carbonate rocks in the lower Paleozoic (lPz) section and incompetent shales and thin-bedded carbonates in the upper Paleozoic (uPz) section. The contrasting mechanical behavior of these stratigraphic sections results in faulted folds within uPz carbonates above detachments in shale-rich units, deforming in response to ramp-flat thrust faulting of the underlying lPz units. East of the axis of the Conger Mountain (Mtn) syncline, we attribute the increase in structural elevation of lPz rocks to a subsurface thrust sheet consisting of lPz strata that advanced eastward via a high-angle ramp from a lower detachment in the Kanosh Shale to an upper detachment in the Pilot Shale. The doubling of lPz strata that resulted continues through the eastern Confusion Range where a series of small-displacement thrust faults comprising the Kings Canyon thrust system gently tilt strata to the west. In the Conger Range, west of the Conger Mtn syncline, our analysis focuses on reinterpreting the geometrically unlikely folding depicted in previous cross sections as more admissible, fault-cored, asymmetric, detached folding. In our interpretation, resistance created by a steeply-dipping thrust ramp in the lPz section west of Conger Mtn resulted in folding of uPz strata into an east-vergent anticline. Continued east-vergent contraction against the ramp resulted in the west-dipping limb of the anticline, consisting of Ely Limestone, developing into an overturned, west-vergent, synclinal backfold detached in the Chainman Shale. Further contraction exceeded the fold capacity of the detachment fold and resulted in the formation of the Browns Wash fault as an east-vergent thrust fault. The Browns Wash fault is a key component in the development of the present structural geometry, emplacing a west-vergent overturned syncline (detachment fold) in the hanging wall against an east-vergent overturned syncline (footwall syncline) in the footwall. Further west, underlying the western Conger Range and Buckskin Hills, lPz strata are exposed in what we interpret to be a ramp anticline overlying a subsurface thrust ramp. This interpretation implies a lateral ramp separating lPz rocks in the Buckskin Hills from uPz rocks exposed in the Knoll Hill anticline to the north. UPz and Mesozoic strata exposed to the west on the edge of Snake Valley were emplaced by a Tertiary west-dipping normal fault that truncated the west limb of the ramp anticline.

Revised preliminary geologic map of the Rifle Quadrangle, Garfield County, Colorado

USGS Publications Warehouse

Shroba, R.R.; Scott, R.B.

1997-01-01

The Rifle quadrangle extends from the Grand Hogback monocline into the southeastern part of the Piceance basin. In the northeastern part of the map area, the Wasatch Formation is nearly vertical, and over a distance of about 1 km, the dip decreases sharply from about 70-85o to about 15-30o toward the southwest. No evidence of a fault in this zone of sharp change in dip is observed but exposures in the Shire Member of the Wasatch Formation are poor, and few marker horizons that might demonstrate offset are distinct. In the central part of the map area, the Shire Member is essentially flat lying. In the south and southwest part of the map area, the dominant dip is slightly to the north, forming an open syncline that plunges gently to the northwest. Evidence for this fold also exists in the subsurface from drill-hole data. According to Tweto (1975), folding of the early Eocene to Paleocene Wasatch Formation along the Grand Hogback reqired an early Eocene age for the last phase of Laramide compression. We find the attitude of the Wasatch Formation to be nearly horizontal, essentially parallel to the overlying Anvil Points Member of the Eocene Green River Formation; therefore, we have no information that either confirms or disputes that early Eocene was the time of the last Laramide event. Near Rifle Gap in the northeast part of the map area, the Mesaverde Group locally dips about 10o less steeply than the overlying Wasatch Formation, indicating that not only had the formation of the Hogback monocline not begun by the time the Wasatch was deposited at this locality, but the underlying Mesaverde Group was locally tilted slightly toward the present White River uplift. Also the basal part of the Atwell Gulch Member of the Wasatch Formation consists of fine-grained mudstones and siltstones containing sparse sandstone and rare conglomerates, indicating that the source of sediment was not from erosion of the adjacent Upper Cretaceous Mesaverde Group. The most likely source of andesitic conglomerate clasts abundant in the upper part of the Atwell Gulch Member was Late Cretaceous-Early Tertiary andesitic igneous rocks, remnants of which are present southeast of the Piceance Basin (Tweto, 1979). Thinning of the Atwell Gulch and Molina Members to the northwest also suggests a southeastern source of sediments, ruling out a northeastern source related to earlier deformation of the Upper Cretaceous Mesa Verde Group.

Geologic map of the Silt Quadrangle, Garfield County, Colorado

USGS Publications Warehouse

Shroba, R.R.; Scott, R.B.

2001-01-01

New 1:24,000-scale geologic mapping in the Silt 7.5' quadrangle, in support of the USGS Western Colorado I-70 Corridor Cooperative Geologic Mapping Project, provides new interpretations of the stratigraphy, structure, and geologic hazards in the area of the southwest flank of the White River uplift, the Grand Hogback, and the eastern Piceance Basin. The Wasatch Formation was subdivided into three formal members, the Shire, Molina, and Atwell Gulch Members. Also a sandstone unit within the Shire Member was broken out. The Mesaverde Group consists of the upper Williams Fork Formation and the lower Iles Formation. Members for the Iles Formation consist of the Rollins Sandstone, the Cozzette Sandstone, and the Corcoran Sandstone Members. The Cozzette and Corcoran Sandstone Members were mapped as a combined unit. Only the upper part of the Upper Member of the Mancos Shale is exposed in the quadrangle. From the southwestern corner of the map area toward the northwest, the unfaulted early Eocene to Paleocene Wasatch Formation and underlying Mesaverde Group gradually increase in dip to form the Grand Hogback monocline that reaches 45-75 degree dips to the southwest (section A-A'). The shallow west-northwest-trending Rifle syncline separates the northern part of the quadrangle from the southern part along the Colorado River. Geologic hazards in the map area include erosion, expansive soils, and flooding. Erosion includes mass wasting, gullying, and piping. Mass wasting involves any rock or surficial material that moves downslope under the influence of gravity, such as landslides, debris flows, or rock falls, and is generally more prevalent on steeper slopes. Locally, where the Grand Hogback is dipping greater than 60 degrees and the Wasatch Formation has been eroded, leaving sandstone slabs of the Mesa Verde Group unsupported over vertical distances as great as 500 m, the upper part of the unit has collapsed in landslides, probably by a process of beam-buckle failure. In the source area of these landslides strata are overturned and dip shallowly to the northeast. Landslide deposits now armor Pleistocene pediment surfaces and extend at least 1 km into Cactus Valley. Gullying and piping generally occur on more gentle slopes. Expansive soils and expansive bedrock are those unconsolidated materials or rocks that swell when wet and shrink when dry. Most floods are restricted to low-lying areas. Several gas-producing wells extract methane from coals from the upper part of the Iles Formation.

The 1987 Whittier Narrows, California, earthquake: A Metropolitan shock

NASA Astrophysics Data System (ADS)

Hauksson, Egill; Stein, Ross S.

1989-07-01

Just 3 hours after the Whittier Narrows earthquake struck, it became clear that a heretofore unseen geological structure was seismically active beneath metropolitan Los Angeles. Contrary to initial expectations of strike-slip or oblique-slip motion on the Whittier fault, whose north end abuts the aftershock zone, the focal mechanism of the mainshock showed pure thrust faulting on a deep gently inclined surface [Hauksson et al., 1988]. This collection of nine research reports spans the spectrum of seismological, geodetic, and geological investigations carried out as a result of the Whittier Narrows earthquake. Although unseen, the structure was not unforeseen. Namson [1987] had published a retrodeformable geologic cross section (meaning that the sedimentary strata could be restored to their original depositional position) 100 km to the west of the future earthquake epicenter in which blind, or subsurface, thrust faults were interpreted to be active beneath the folded southern Transverse Ranges. Working 25 km to the west, Hauksson [1987] had also found a surprising number of microearthquakes with thrust focal mechanisms south of the Santa Monica mountains, another clue to a subsurface system of thrust faults. Finally, Davis [1987] had presented a preliminary cross section only 18 km to the west of Whittier Narrows that identified as "fault B" the thrust that would rupture later that year. Not only was the earthquake focus and its orientation compatible with the 10-15 km depth and north dipping orientation of Davis' proposed thrust, but fault B appears to continue beneath the northern flank of the Los Angeles basin, skirting within 5 km of downtown Los Angeles, an area of dense commercial high-rise building development. These results are refined and extended by Davis et al. [this issue].

Structure of the western Rif (Morocco): Possible hydrocarbon plays

DOE Office of Scientific and Technical Information (OSTI.GOV)

Flinch, J.

1995-08-01

Seismic data offshore and onshore northwestern Morocco (i.e. Atlantic margin, Rharb Basin, Rif foothills) provided a detailed picture of the Western Rif Cordillera. The most external units of the folded-belt consist of allochthonous Cretaceous and Neogene strongly deformed sediments that constitute a westward-directed accretionary wedge. The structure of the accretionary wedge consist of a complex set of thrust and normal faults. The inner part of the study area consist of NW-SE trending thrust faults, partially exposed in the foothills of the Western Rif. Proceeding towards the foreland, thrust faults are offset by low-angle extensional detachments characterized by anastomosing extensional horses.more » Widespread extension overlying the accretionary wedge defines a Late Neogene episode of extensional collapse. Extension is not characterized by localized conventional half-grabens but consists of a complex extensional system with variable orientation. Locally shale ridges and toe-thrusts characterized by rear extension and frontal compression define a set of mixed extensional-compressional satellite basins that significantly differ from conventional thrust-related piggy-back basins. Satellite basins are filled with Upper Tortonian to Pliocene sediments. Shallow fields of biogenic gas are present in this Upper Neogene succession of the satellite basins. The frontalmost part of the wedge consist of WNW-ESE trending thrust imbricates. A flexural basin (foredeep) developed as a result of the accretionary prism loading. The foredeep basin discordantly overlies thinn Cretaceous and Lower-Middle Miocene shallow-water sediments that indistinctly cover Plaeozoic basement rocks and Triassic half-grabens. Pre-foredeep units are related to rifting and passive margin development of the Atlantic Ocean. East from the Rharb Basin the Rif Cordillera is essentially unexplored. Few scattered seismic sections display subsurface ramp anticlines similar to those exposed in the mountain belt.« less

How the structural architecture of the Eurasian continental margin affects the structure, seismicity, and topography of the south central Taiwan fold-and-thrust belt

NASA Astrophysics Data System (ADS)

Brown, Dennis; Alvarez-Marron, Joaquina; Biete, Cristina; Kuo-Chen, Hao; Camanni, Giovanni; Ho, Chun-Wei

2017-07-01

Studies of mountain belts worldwide show that along-strike changes are common in their foreland fold-and-thrust belts. These are typically caused by processes related to fault reactivation and/or fault focusing along changes in sedimentary sequences. The study of active orogens, like Taiwan, can also provide insights into how these processes influence transient features such as seismicity and topography. In this paper, we trace regional-scale features from the Eurasian continental margin in the Taiwan Strait into the south central Taiwan fold-and-thrust belt. We then present newly mapped surface geology, P wave velocity maps and sections, seismicity, and topography data to test the hypothesis of whether or not these regional-scale features of the margin are contributing to along-strike changes in structural style, and the distribution of seismicity and topography in this part of the Taiwan fold-and-thrust belt. These data show that the most important along-strike change takes place at the eastward prolongation of the upper part of the margin necking zone, where there is a causal link between fault reactivation, involvement of basement in the thrusting, concentration of seismicity, and the formation of high topography. On the area correlated with the necking zone, the strike-slip reactivation of east northeast striking extensional faults is causing sigmoidal offset of structures and topography along two main zones. Here basement is not involved in the thrusting; there is weak focusing of seismicity and localized development of topography. We also show that there are important differences in structure, seismicity, and topography between the margin shelf and its necking zone.

Foreshock occurrence before large earthquakes

USGS Publications Warehouse

Reasenberg, P.A.

1999-01-01

Rates of foreshock occurrence involving shallow M ??? 6 and M ??? 7 mainshocks and M ??? 5 foreshocks were measured in two worldwide catalogs over ???20-year intervals. The overall rates observed are similar to ones measured in previous worldwide and regional studies when they are normalized for the ranges of magnitude difference they each span. The observed worldwide rates were compared to a generic model of earthquake clustering based on patterns of small and moderate aftershocks in California. The aftershock model was extended to the case of moderate foreshocks preceding large mainshocks. Overall, the observed worldwide foreshock rates exceed the extended California generic model by a factor of ???2. Significant differences in foreshock rate were found among subsets of earthquakes defined by their focal mechanism and tectonic region, with the rate before thrust events higher and the rate before strike-slip events lower than the worldwide average. Among the thrust events, a large majority, composed of events located in shallow subduction zones, had a high foreshock rate, while a minority, located in continental thrust belts, had a low rate. These differences may explain why previous surveys have found low foreshock rates among thrust events in California (especially southern California), while the worldwide observations suggests the opposite: California, lacking an active subduction zone in most of its territory, and including a region of mountain-building thrusts in the south, reflects the low rate apparently typical for continental thrusts, while the worldwide observations, dominated by shallow subduction zone events, are foreshock-rich. If this is so, then the California generic model may significantly underestimate the conditional probability for a very large (M ??? 8) earthquake following a potential (M ??? 7) foreshock in Cascadia. The magnitude differences among the identified foreshock-mainshock pairs in the Harvard catalog are consistent with a uniform distribution over the range of observation.

Ouachitas need more exploratory drilling

USGS Publications Warehouse

Suneson, Neil H.; Campbell, Jock A.

1990-01-01

The Ouachita Mountains in southeastern Oklahoma and western Arkansas are part of a mostly buried late Paleozoic fold and thrust belt that extends from Alabama to northern Mexico. The principal hydrocarbon reservoirs in the Ouachita tectonic province can be subdivided into those that produce natural gas from shallow-water units and those that produce oil and/or natural gas from deep-water units. They can also be divided into those that are fractured and those that produce from primary pore spaces or vugs. The first successful oil well in the Ouachita Mountains was drilled in 1913 or 1914. Since the discovery of the Redden field, over 800 oil and gas wells have been drilled in the Ouachita tectonic province in Oklahoma. Yet, most of the region remains little explored.

Growth of the Zagros Fold-Thrust Belt and Foreland Basin, Northern Iraq, Kurdistan

NASA Astrophysics Data System (ADS)

Koshnaw, Renas; Horton, Brian; Stockli, Daniel; Barber, Douglas; Ghalib, Hafidh; Dara, Rebwar

2016-04-01

The Zagros orogenic belt in the Middle Eastern segment of the Alpine-Himalayan system is among the youngest seismically active continental collision zones on Earth. However, due to diachronous and incremental collision, the precise ages and kinematics of shortening and deposition remain poorly understood. The Kurdistan region of the Zagros fold-thrust belt and foreland basin contains well-preserved Neogene wedge-top and foredeep deposits that include clastic nonmarine fill of the Upper Fars, Lower Bakhtiari, and Upper Bakhtiari Formations. These deposits record significant information about orogenic growth, fold-thrust dynamics, and advance of the deformation front. Thermochronologic and geochronologic data from thrust sheets and stratigraphic archives combined with local earthquake data provide a unique opportunity to address the linkages between surface and subsurface geologic relationships. This research seeks to constrain the timing and geometry of exhumation and deformation by addressing two key questions: (1) Did the northwestern Zagros fold-thrust belt evolve from initial thin-skinned shortening to later thick-skinned deformation or vice-versa? (2) Did the fold-thrust belt advance steadily under critical/supercritical wedge conditions involving in-sequence thrusting or propagate intermittently under subcritical conditions with out-of-sequence deformation? From north to south, apatite (U-Th)/He ages from the Main Zagros Thrust, the Mountain Front Flexure (MFF), and additional frontal thrusts suggest rapid exhumation by ~10 Ma, ~5 Ma, and ~8 Ma respectively. Field observations and seismic sections indicate progressive tilting and development of growth strata within the Lower Bakhtiari Formation adjacent to the frontal thrusts and within the Upper Bakhtiari Formation near the MFF. In the Kurdistan region of Iraq, a regional balanced cross section constrained by new thermochronometric results, proprietary seismic reflection profiles, and earthquake hypocenters suggest prolonged thin-skinned shortening in sequence from north to south followed by a thick-skinned out-of-sequence MFF deformation and intermittent hinterland uplift postdating initial collision. Magnetostratigraphic analyses of Dinarta wedge-top deposits and Kifri foredeep deposits constrain accumulation of the Upper Fars-Lower Bakhtiari synorogenic succession to 12.5-5 Ma. These findings suggest that temporal and spatial shifts in upper-crustal modes of deformation in the Kurdistan segment of the Zagros orogenic belt strongly influenced patterns of topographic growth, landscape development, and resulting foreland basin stratigraphy.

Active Tectonics of Himalayan Faults/Thrusts System in Northern India on the basis of recent & Paleo earthquake Studies

NASA Astrophysics Data System (ADS)

Kumar, S.; Biswal, S.; Parija, M. P.

2016-12-01

The Himalaya overrides the Indian plate along a decollement fault, referred as the Main Himalayan Thrust (MHT). The 2400 km long Himalayan mountain arc in the northern boundary of the Indian sub-continent is one of the most seismically active regions of the world. The Himalayan Frontal Thrust (HFT) is characterized by an abrupt physiographic and tectonic break between the Himalayan front and the Indo-Gangetic plain. The HFT represents the southern surface expression of the MHT on the Himalayan front. The tectonic zone between the Main Boundary Thrust (MBT) and the HFT encompasses the Himalayan Frontal Fault System (HFFS). The zone indicates late Quaternary-Holocene active deformation. Late Quaternary intramontane basin of Dehradun flanked to the south by the Mohand anticline lies between the MBT and the HFT in Garhwal Sub Himalaya. Slip rate 13-15 mm/yr has been estimated on the HFT based on uplifted strath terrace on the Himalyan front (Wesnousky et al. 2006). An out of sequence active fault, Bhauwala Thrust (BT), is observed between the HFT and the MBT. The Himalayan Frontal Fault System includes MBT, BT, HFT and PF active fault structures (Thakur, 2013). The HFFS structures were developed analogous to proto-thrusts in subduction zone, suggesting that the plate boundary is not a single structure, but series of structures across strike. Seismicity recorded by WIHG shows a concentrated belt of seismic events located in the Main Central Thrust Zone and the physiographic transition zone between the Higher and Lesser Himalaya. However, there is quiescence in the Himalayan frontal zone where surface rupture and active faults are reported. GPS measurements indicate the segment between the southern extent of microseismicity zone and the HFT is locked. The great earthquake originating in the locked segment rupture the plate boundary fault and propagate to the Himalaya front and are registered as surface rupture reactivating the fault in the HFFS.

The San Gabriel mountains bright reflective zone: Possible evidence of young mid-crustal thrust faulting in southern California

USGS Publications Warehouse

Ryberg, T.; Fuis, G.S.

1998-01-01

During the Los Angeles Region Seismic Experiment (LARSE), a reflection/retraction survey was conducted along a line extending northeastward from Seal Beach, California, to the Mojave Desert, crossing the Los Angeles basin and San Gabriel Mountains. Shots and receivers were spaced most densely through the San Gabriel Mountains for the purpose of obtaining a combined reflection and refraction image of the crust in that area. A stack of common-midpoint (CMP) data reveals a bright reflective zone, 1-s thick, that dominates the stack and extends throughout most of the mid-crust of the San Gabriel Mountains. The top of this zone ranges in depth from 6 s (???18-km depth) in the southern San Gabriel Mountains to 7.5 s (???23-km depth) in the northern San Gabriel Mountains. The zone bends downward beneath the surface traces of the San Gabriel and San Andreas faults. It is brightest between these two faults, where it is given the name San Gabriel Mountains 'bright spot' (SGMBS). and becomes more poorly defined south of the San Gabriel fault and north of the San Andreas fault. The polarity of the seismic signal at the top of this zone is clearly negative, and our analysis suggests it represents a negative velocity step. The magnitude of the velocity step is approximately 1.7 km/s. In at least one location, an event with positive polarity can be observed 0.2 s beneath the top of this zone, indicating a thickness of the order of 500 m for the low-velocity zone at this location. Several factors combine to make the preferred interpretation of this bright reflective zone a young fault zone, possibly a 'master' decollement. (1) It represents a significant velocity reduction. If the rocks in this zone contain fluids, such a reduction could be caused by a differential change in fluid pressure between the caprock and the rocks in the SGMBS; near-lithostatic fluid pressure is required in the SGMBS. Such differential changes are believed to occur in the neighborhood of active fault zones, where 'fault-valve' action has been postulated. Less likely alternative explanations for this velocity reduction include the presence of magma and a change in composition to serpentinite or metagraywacke. (2) It occurs at or near the brittle-ductile transition, at least in the southern San Gabriel Mountains, a possible zone of concentrated shear. (3) A thin reflection rising from its top in the southern San Gabriel Mountains projects to the hypocenter of the 1987 M 5.9 Whittier Narrows earthquake, a blind thrust-fault earthquake with one focal plane subparallel to the reflection. Alternatively, one could argue that the bends or disruptions in the reflective zone seen at the San Gabriel and San Andreas faults are actually offsets and that the reflective zone is therefore an older feature, possibly an older fault zone. ?? 1998 Elsevier Science B.V. All rights reserved.

Geology of the Yucca Mountain region

USGS Publications Warehouse

Stuckless, J.S.; O'Leary, Dennis W.

2006-01-01

Yucca Mountain has been proposed as the site for the nation's first geologic repository for high-level radioactive waste. This chapter provides the geologic framework for the Yucca Mountain region. The regional geologic units range in age from late Precambrian through Holocene, and these are described briefly. Yucca Mountain is composed dominantly of pyroclastic units that range in age from 11.4 to 15.2 Ma. The proposed repository would be constructed within the Topopah Spring Tuff, which is the lower of two major zoned and welded ash-flow tuffs within the Paintbrush Group. The two welded tuffs are separated by the partly to nonwelded Pah Canyon Tuff and Yucca Mountain Tuff, which together figure prominently in the hydrology of the unsaturated zone. The Quaternary deposits are primarily alluvial sediments with minor basaltic cinder cones and flows. Both have been studied extensively because of their importance in predicting the long-term performance of the proposed repository. Basaltic volcanism began ca. 10 Ma and continued as recently as ca. 80 ka with the eruption of cones and flows at Lathrop Wells, ???10 km south-southwest of Yucca Mountain. Geologic structure in the Yucca Mountain region is complex. During the latest Paleozoic and Mesozoic, strong compressional forces caused tight folding and thrust faulting. The present regional setting is one of extension, and normal faulting has been active from the Miocene through to the present. There are three major local tectonic domains: (1) Basin and Range, (2) Walker Lane, and (3) Inyo-Mono. Each domain has an effect on the stability of Yucca Mountain. ?? 2007 Geological Society of America. All rights reserved.

Latest Pleistocene to Holocene Thrusting Recorded by a Flight of Strath Terraces in the Eastern Qilian Shan, NE Tibetan Plateau

NASA Astrophysics Data System (ADS)

Xiong, Jianguo; Li, Youli; Zhong, Yuezhi; Lu, Honghua; Lei, Jinghao; Xin, Weilin; Wang, Libo; Hu, Xiu; Zhang, Peizhen

2017-12-01

At the eastern Qilian Shan mountain front in the NE Tibetan Plateau, the Minle-Damaying Fault (MDF), the southernmost fault of the North Frontal Thrust (NFT) system, has previously been proposed as an inactive structure during the Holocene. Here we present a detailed record of six strath terraces of the Xie River that document the history of active deformation of the MDF. One optically stimulated luminescence dating sample constrains abandonment of the highest terrace T6 at 12.7 ± 1.4 ka. The formation ages of the lower terraces (T4-T1) are dated by AMS 14C dating. The cumulative vertical offsets of the MDF recorded by these terraces are determined as 12.2 ± 0.4 m (T6), 8.0 ± 0.4 m (T5), 6.4 ± 0.4 m (T4), 4.6 ± 0.1 m (T3), and 3.2 ± 0.2 m (T1c) by an unmanned aerial vehicle system, respectively. A long-term vertical slip rate of the MDF of 0.9 ± 0.2 mm/yr is then estimated from the above data of terrace age and vertical offset by a linear regression. Assuming that the fault dip of 35 ± 5° measured at the surface is representative for the depth-averaged fault dip, horizontal shortening rates of 0.83-1.91 mm/yr are inferred for the MDF. Our new data show that the proximal fault (the MDF) of the NFT system at the eastern Qilian Shan mountain front has remained active when the deformation propagated basinward, a different scenario from that observed at both the western and central Qilian Shan mountain front.

Thin-skinned tectonics of the Upper Ojai Valley and Sulphur Mountain area, Ventura basin, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huftile, G.J.

1991-08-01

By integrating surface mapping with subsurface well data and drawing cross sections and subsurface maps, the geometry of shallow structures and their geologic history of the Upper Ojai Valley of California can be reconstructed. The geometry of shallow structures, the geologic history, and the location of earthquake foci then offer constraints on the deep structure of this complex area. The Upper Ojai Valley is a tectonic depression between opposing reverse faults. Its northern border is formed by the active, north-dipping San Cayetano fault, which has 6.0 km of stratigraphic separation in the Silverthread area of the Ojai oil field andmore » 2.6 km of stratigraphic separation west of Sisar Creek. The fault dies out farther west in Ojai Valley, where the south-vergent shortening is transferred to a blind thrust. The southern border of the Upper Ojai Valley is formed by the Quaternary Lion fault set, which dips south and merges into the Sisar decollement within the south-dipping, ductile, lower Miocene Rincon formation. By the middle Pleistocene, the Sulphur Mountain anticlinorium and the Big Canyon syncline began forming as a fault-propagation fold; the fault-propagation fold is rooted in the Sisar decollement, a passive backthrust rising from a blind thrust at depth. The formation of the Sulphur Mountain anticlinorium was followed closely by the ramping of the south-dipping Lion fault set to the surface over the nonmarine upper Pleistocene Saugus Formation. To the east, the San Cayetano fault overrides and folds the Lion Fault set near the surface. Area-balancing of the deformation shows shortening of 15.5 km, and suggests a 17 km depth to the brittle-ductile transition.« less

Restoration of the Cretaceous uplift of the Harz Mountains, North Germany: evidence for the geometry of a thick-skinned thrust

NASA Astrophysics Data System (ADS)

Tanner, David C.; Krawczyk, Charlotte M.

2017-04-01

Reverse movement on the Harz Northern Boundary Fault was responsible for the Late Cretaceous uplift of the Harz Mountains in northern Germany. Using the known geometry of the surface position and dip of the fault, and a published cross section of the Base Permian horizon, we show that it is possible to predict the probable shape of the fault at depth, down to a detachment level. We use the `inclined-shear' method with constant heave and argue that a shear angle of 30° was most likely. In this case, the detachment level is at a depth of ca. 25 km. Kinematic restoration of the Harz Mountains using this fault geometry does not produce a flat horizon, rather it results in a ca. 4 km depression. Airy-Heiskanen isostatic equilibrium adjustment of the Harz Mountains restores the Base Permian horizon to the horizontal, as well as raising the Moho to a depth of 32 km, a typical value for northern Germany. Restoration also causes a rotation of tectonic fabrics within the Harz Mountains of about 11° clockwise. We show that this model geometry is very good fit to the interpreted DEKORP BASIN 9601 deep seismic profile.

Pennsylvanian-Permian tectonism in the Great Basin: The Dry Mountain trough and related basins

DOE Office of Scientific and Technical Information (OSTI.GOV)

Snyder, W.S.; Spinosa, C.; Gallegos, D.M.

1991-02-01

Pennsylvanian-Permian tectonism affected the continental margin of western North America from the Yukon to the Mojave Desert. Specific signatures of this tectonism include local angular unconformities, regional disconformities, renewed outpouring of clastic debris from a reactivated Antler and related highlands, and development of deeper water basins with anoxic sediments deposited below wave base. The basins formed include Ishbel trough (Canada), the Wood River basin (Idaho), Cassia basin, Ferguson trough, Dry Mountain trough (all Nevada), and unnamed basins in Death Valley-Mojave Desert region. The Dry Mountain trough (DMT) was initiated during early Wolfcampian and received up to 1,200 m of sedimentmore » by the late Leonardian. The lower contact is a regional unconformity with the Ely Limestone, or locally with the Diamond Peak or Vinini formations. Thus, following a period of localized regional uplift that destroyed the Ely basin, portions of the uplifted and exposed shelf subsided creating the Dry Mountain trough. Evidence suggesting a tectonic origin for the DMT includes (1) high subsidence rates (60-140 m/m.y.); (2) renewed influx of coarse clastic debris from the Antler highlands: (3) possible pre-Early Permian folding, thrusting, and tilting within the highlands; and (4) differential subsidence within the Dry Mountain trough, suggesting the existence of independent fault blocks.« less

Interseismic coupling, seismic potential, and earthquake recurrence on the southern front of the Eastern Alps (NE Italy)

NASA Astrophysics Data System (ADS)

Cheloni, D.; D'Agostino, N.; Selvaggi, G.

2014-05-01

Here we use continuous GPS observations to document the geodetic strain accumulation across the South-Eastern Alps (NE Italy). We estimate the interseismic coupling on the intracontinental collision thrust fault and discuss the seismic potential and earthquake recurrence. We invert the GPS velocities using the back slip approach to simultaneously estimate the relative angular velocity and the degree of interseismic coupling on the thrust fault that separates the Eastern Alps and the Venetian-Friulian plain. Comparison between the rigid rotation predicted motion and the shortening observed across the area indicates that the South-Eastern Alpine thrust front absorbs about 70% of the total convergence between the Adria and Eurasia plates. The coupling is computed on a north dipping fault following the continuous external seismogenic thrust front of the South-Eastern Alps. The modeled thrust fault is currently locked from the surface to a depth of ≈10 km. The transition zone between locked and creeping portions of the fault roughly corresponds with the belt of microseismicity parallel and to the north of the mountain front. The estimated moment deficit rate is 1.3 ± 0.4 × 1017 Nm/yr. The comparison between the estimated moment deficit and that released historically by the earthquakes suggests that to account for the moment deficit the following two factors or their combination should be considered: (1) a significant part of the observed interseismic coupling is released aseismically and (2) infrequent "large" events with long return period (> 1000 years) and with magnitudes larger than the value assigned to the largest historical events (Mw≈ 6.7).

Active deformation and seismicity in the Southern Alps (Italy): The Montello hill as a case study

NASA Astrophysics Data System (ADS)

Danesi, Stefania; Pondrelli, Silvia; Salimbeni, Simone; Cavaliere, Adriano; Serpelloni, Enrico; Danecek, Peter; Lovati, Sara; Massa, Marco

2015-06-01

The Montello anticline is a morphotectonic feature of the east pede-mountain of the South Alpine Chain in northern Italy, which lies ca. 40 km northwest of Venice, Italy. The purpose of this study is to characterize the present-day crustal deformation and seismotectonics of the Montello area through multi-parametric geophysical observations. We used new data obtained from the installation of a temporary network of 12 seismic stations and 6 GPS sites. The GPS observations indicate that there is ~ 1 mm/yr shortening across the Montello thrust. Sites located north of the Montello thrust front deviate from the ~ NNW-ward Adria-Eurasia convergence direction, as they are constrained by a relative rotation pole in northwestern Italy that has a NNE-ward motion trend. Over 18 months, seismographic recordings allowed us to locate 142 local seismic events with Ml 0.5-3.5 with good reliability (rms < 0.5). After cross-correlation analysis, we classified 42 of these events into six clusters, with cross-correlation thresholds > 0.80. The source focal solutions indicate that: (i) there is thrusting seismic activity on the basal, sub-horizontal, portion of the Montello structure; and (ii) strike-slip source kinematics prevail on the western edge of the Montello hill. Our observations on the source mechanisms and the measured crustal deformation confirm that the Montello thrust is tectonically active.

Geologic map of the Boulder-Fort Collins-Greeley Area, Colorado

USGS Publications Warehouse

Colton, Roger B.

1978-01-01

This digital map shows the geographic extent of rock stratigraphic units (formations) as compiled by Colton in 1976 under the Front Range Urban Corridor Geology Program. Colton used his own geologic mapping and previously published geologic maps to compile one map having a single classification of geologic units. The resulting published color paper map (USGS Map I-855-G, Colton, 1978) was intended for land-use planning and to depict the regional geology. In 1997-1999, another USGS project designed to address urban growth issues was undertaken. This project, the USGS Front Range Infrastructure Resources Project, undertook to digitize Colton's map at 1:100,000 scale, making it useable in Geographical Information Systems (GIS). That product is described here. In general, the digitized map depicts in its western part Precambrian igneous and metamorphic rocks, Pennsylvanian and younger sedimentary rock units, major faults, and brecciated zones along an eastern strip (5-20 km wide) of the Front Range. The central and eastern parts of the map (Colorado Piedmont) show a mantle of Quaternary unconsolidated deposits and interspersed outcrops of sedimentary rock of Cretaceous or Tertiary age. A surficial mantle of unconsolidated deposits of Quaternary age is differentiated and depicted as eolium (wind-blown sand and silt), alluvium (river gravel, sand, and silt of variable composition), colluvium, and a few landslide deposits. At the mountain front, north-trending, Paleozoic and Mesozoic formations of sandstone, shale, and minor limestone dip mostly eastward and form folds, fault blocks, hogbacks and intervening valleys. Local dikes and sills of Tertiary rhyodacite and basalt intrude rocks near the range front, mostly in the Boulder area.

A spatial database of bedding attitudes to accompany Geologic Map of Boulder-Fort Collins-Greeley Area, Colorado

USGS Publications Warehouse

Colton, Roger B.; Brandt, Theodore R.; Moore, David W.; Murray, Kyle E.

2003-01-01

This digital map shows bedding attitude data displayed over the geographic extent of rock stratigraphic units (formations) as compiled by Colton in 1976 (U.S.Geological Survey Map I-855-G) under the Front Range Urban Corridor Geology Program. Colton used his own mapping and published geologic maps having varied map unit schemes to compile one map with a uniform classification of geologic units. The resulting published color paper map was intended for planning for use of land in the Front Range Urban Corridor. In 1997-1999, under the USGS Front Range Infrastructure Resources Project, Colton's map was digitized to provide data at 1:100,000 scale to address urban growth issues(see cross-reference). In general, the west part of the map shows a variety of Precambrian igneous and metamorphic rocks, major faults and brecciated zones along an eastern strip (5-20 km wide) of the Front Range. The eastern and central part of the map (Colorado Piedmont) depicts a mantle of Quaternary unconsolidated deposits and interspersed Cretaceous or Tertiary-Cretaceous sedimentary rock outcrops. The Quaternary mantle is comprised of eolian deposits (quartz sand and silt), alluvium (gravel, sand, and silt of variable composition), colluvium, and few landslides. At the mountain front, north-trending, dipping Paleozoic and Mesozoic sandstone and shale formations (and sparse limestone) form hogbacks, intervening valleys, and in range-front folds, anticlines, and fault blocks. Localized dikes and sills of Tertiary rhyodacite and basalt intrude rocks near the range front, mostly in the Boulder area.

The Junction of Hellenic and Cyprus Arcs: the Bey Daglari Lineament, Offshore Termination of the Antalya Basin

NASA Astrophysics Data System (ADS)

Gogacz, A.; Hall, J.; Cifci, G.; Yasar, D.; Kucuk, M.; Yaltirak, C.; Aksu, A.

2009-05-01

The Antalya Basin is one of a series of basins that sweep along the Cyprus Arc in the forearc region between the (formerly) volcanic Tauride Mountains on Turkey in the north and the subduction zone and associated suture between the African plate and the Aegean-Anatolian microplate in the eastern Mediterranean, south of Cyprus. Miocene contraction occurs widely on southwest verging thrusts. Pliocene-Quaternary structures vary from extension/transtension in the northeast, adjacent to the Turkish coastline, to transpression in the southwest, farther offshore. All these structures are truncated at the northwest end of the Antalya Basin by a broad zone of NNE-SSW-trending transverse structure that appears to represent a prolongation of the extreme easterly transform end of the Hellenic arc. Our mapping suggests that this broad zone links the Hellenic Arc with the Isparta Angle in southern Turkey, which we suggest is an earlier location of the junction of Hellenic and Cyprus Arcs: the junction migrated to the southwest over time, as the Hellenic Arc rolled back. The Turkish coastline turns from parallel to the Antalya Basin structures in the east to a N-S orientation, cutting across the trend of the Antalya Basin. The Antalya Complex and the Bey Dağları Mountains provide a spectacular backdrop to this edge of the offshore basin. Somewhere offshore lies the structural termination of the Antalya Basin. In 2001, we acquired around 400 km of high-resolution multi-channel seismic reflection data across the western end of the Antalya Basin to explore the nature of the termination, which we call the Bey Dağları lineament. We present a selection of the seismic profiles with interpretation of the nature and Neogene history of the lineament. Landward of the N-S-trending coastline, ophiolites of the Antalya Complex are exposed in a series of westerly-verging thrust slivers that extend to the carbonate sequences of the Bey Dağları Mountains. Our seismic data indicate that N-S trending west- and east-verging thrusts define a transpressional continental margin. The shelf is underlain by a prominent angular unconformity between overlying shallow-dipping Pliocene-Quaternary sediments and underlying, easterly- dipping ?Miocene sediments.

Source and tectonic implications of tonalite-trondhjemite magmatism in the Klamath Mountains

USGS Publications Warehouse

Barnes, C.G.; Petersen, S.W.; Kistler, R.W.; Murray, R.; Kays, M.A.

1996-01-01

In the Klamath Mountains, voluminous tonalite-trondhjemite magmatism was characteristic of a short period of time from about 144 to 136 Ma (Early Cretaceous). It occurred about 5 to l0 m.y. after the ??? 165 to 159 Ma Josephine ophiolite was thrust beneath older parts of the province during the Nevadan orogeny (thrusting from ??? 155 to 148 Ma). The magmatism also corresponds to a period of slow or no subduction. Most of the plutons crop out in the south-central Klamath Mountains in California, but one occurs in Oregon at the northern end of the province. Compositionally extended members of the suite consist of precursor gabbroic to dioritic rocks followed by later, more voluminous tonalitic and trondhjemitic intrusions. Most plutons consist almost entirely of tonalite and trondhjemite. Poorlydefined concentric zoning is common. Tonalitic rocks are typically of the Iow-Al type but trondhjemites are generally of the high-Al type, even those that occur in the same pluton as low-Al tonalite??. The suite is characterized by low abundances of K2O, Rb, Zr, and heavy rare earth elements. Sr contents are generally moderate ( ???450 ppm) by comparison with Sr-rich arc lavas interpreted to be slab melts (up to 2000 ppm). Initial 87Sr/ 86Sr, ??18O, and ??Nd are typical of mantle-derived magmas or of crustally-derived magmas with a metabasic source. Compositional variation within plutons can be modeled by variable degrees of partial melting of a heterogeneous metabasaltic source (transitional mid-ocean ridge to island arc basalt), but not by fractional crystallyzation of a basaltic parent. Melting models require a residual assemblage of clinopyroxene+garnet??plagioclase??amphibole; residual plagioclase suggests a deep crustal origin rather than melting of a subducted slab. Such models are consistent with the metabasic part of the Josephine ophiolite as the source. Because the Josephine ophiolite was at low T during Nevadan thrusting, an external heat source was probably necessary to achieve significant degrees of melting; heat was probably extracted from mantle-derived basaltic melts, which were parental to the mafic precursors of the tonalite-trondhjemite suite. Thus, under appropriate tectonic and thermal conditions, heterogeneous mafic crustal rocks can melt to form both low- and high-Al tonalitic and trondhjemitic magmas; slab melting is not necessary.

Role of Fluids in Mechanics of Overthrust Faulting on Titan

NASA Astrophysics Data System (ADS)

Liu, Z.; Radebaugh, J.; Harris, R. A.; Christiansen, E. H.

2013-12-01

Since Cassini has unveiled Titan's surface, its mountains have been commonly associated with contractional tectonism. However, in order to form contractional structures on icy satellites, relatively large stresses are required. The stress required to form contractional structures on Ganymede and Europa is 3-8 times that required for extensional features. Sources of such stresses probably do not exist for most icy satellites. Therefore, a paradox has emerged, wherein no stress source is known that is large enough to produce the contractional structures observed on Titan. A possible solution for the strength paradox is inspired by Hubbert and Rubey (1959) who demonstrated how high fluid pressures reduce the normal stress along a fault plane, therefore significantly reducing frictional resistance to thrusting. Since liquid hydrocarbons have been identified on Titan's surface and may flow in the subsurface, we speculate that fluid pressures associated with liquid hydrocarbons in the subsurface significantly reduce the shear strength of the icy crust and enable contractional structures to form without the requiring large stresses. We use critical wedge theory, which is a mechanism for driving fold-and-thrust belt formation, to test if the slope angles of mountains and crustal conditions with estimated fluid pressures favor the formation of fold-thrust belts on Titan. We evaluated 6 mountain belts with available Cassini SARTopo data using critical wedge calculations. The slopes of 10 traces from valley floors to summits are between 0.4 and 2.5 degrees. We use the measured slopes with varying friction coefficients and fluid pressures to calculate the range of dip angles. The results yielded 840 dip angle values, 689 (82%) of which were in a reasonable range, and consistent with fold belt formation in critical wedge settings. We conclude that crustal liquids have played a key role in Titan's tectonic history. Our results highlight the significance of fluids in planetary lithospheres and have implications for tectonics on all solid bodies that may have fluid in their lithospheres, now or in the past. Reference: Hubbert, M. K. & Rubey, W. W. Role of fluid pressure in mechanics of overthrust faulting I. Mechanics of fluid-filled porous solids and its application to overthrust faulting. Geol. Soc. Am. Bull. 70, 2, 115-166 (1959).

Paleoseismology at high latitudes: Seismic disturbance of upper Quaternary deposits along the Castle Mountain fault near Houston, Alaska

USGS Publications Warehouse

Haeussler, Peter J.; Best, Timothy C.; Waythomas, Christopher F.

2002-01-01

Most paleoseismic studies are at low to moderate latitudes. Here we present results from a high-latitude (61°30′ N) trenching study of the Castle Mountain fault in south-central Alaska. This fault is the only one known in the greater Anchorage, Alaska, area with historical seismicity and a Holocene fault scarp. It strikes east-northeast and cuts glacial and postglacial sediments in an area of boreal spruce-birch forest, shrub tundra, and sphagnum bog. The fault has a prominent vegetation lineament on the upthrown, north side of the fault. Nine trenches were logged across the fault in glacial and postglacial deposits, seven along the main trace, and two along a splay. In addition to thrust and strike-slip faulting, important controls on observed relationships in the trenches are the season in which faulting occurred, the physical properties of the sediments, liquefaction, a shallow water table, soil-forming processes, the strength of the modern root mat, and freeze-thaw processes. Some of these processes and physical properties are unique to northern-latitude areas and result in seismic disturbance effects not observed at lower latitudes.The two trenches across the Castle Mountain fault splay exposed a thrust fault and few liquefaction features. Radiocarbon ages of soil organic matter and charcoal within and overlying the fault indicate movement on the fault at ca. 2735 cal. (calendar) yr B.P. and no subsequent movement. In the remaining seven trenches, surface faulting was accompanied by extensive liquefaction and a zone of disruption 3 m or more wide. The presence of numerous liquefaction features at depths of <0.5–1.0 m indicates faulting when the ground was not frozen—i.e., from about April to October. Sandy-matrix till, sand, silt, gravel, and pebbly peat were injected up to the base of the modern soil, but did not penetrate the interlocking spruce-birch root mat. The strength of the root mat prohibited development of a nonvegetated scarp face and colluvial wedge. In only one trench did we observe a discrete fault plane with measurable offset. It lay beneath a 2-m-thick carapace of liquefied sand and silt and displayed a total of 0.9–1.85 m of thrust motion since deposition of the oldest deposits in the trenches at ca. 13,500 yr B.P. We found liquefaction ejecta on paleosols at only one other trench, where there were bluejoint (Calamagrostis canadensis) tussocks that lacked an extensive root mat. From crosscutting relationships, we interpret three paleoliquefaction events on the main trace of the Castle Mountain fault: 2145–1870, 1375–1070, and 730–610 cal. yr B.P. These four earthquakes on the Castle Mountain fault in the past ∼2700 yr indicate an average recurrence interval of ∼700 yr. As it has been 600–700 yr since the last significant earthquake, a significant (magnitude 6–7) earthquake in the near future may be likely. Paleoseismic data indicate that the timing and recurrence interval of megathrust earthquakes is similar to the timing and recurrence interval of Castle Mountain fault earthquakes, suggesting a possible link between faulting on the megathrust and on “crustal” structures.

Applied geochemistry, geology and mineralogy of the northernmost Carlin trend, Nevada

USGS Publications Warehouse

Theodore, T.G.; Kotlyar, B.B.; Singer, D.A.; Berger, V.I.; Abbott, E.W.; Foster, A.L.

2003-01-01

Investigations in the northernmost Carlin trend were undertaken to advance understanding of the geochemical signatures and genesis of precious metal deposits in the trend. Two fundamental geologic relationships near the trend significantly affect regional geochemical distributions: a remarkably intact lower Paleozoic stratigraphic sequence of siliceous rocks in the upper plate of the middle Paleozoic Roberts Mountains thrust, and the widespread repetition of rocks high in the upper plate during late Paleozoic thrusting that thickens the cover above mineralized rock in the lower plate. A compilation of previously published chemical analyses of 440 stream sediment samples and 115 rocks from two 7 1/2-minute quadrangles, as well as new chemical analyses of approximately 1,000 drill core samples in a 1,514 m (4,970 ft) hole through the Rodeo Creek deposit were used to construct three-dimensional element distribution models that highlight metal zonation in the mineralized systems. The Rodeo Creek deposit comprises deep Ag base-metal ?? Au-mineralized rock below the Roberts Mountains thrust and contains an unusually high Ag/Au ratio greater than 30. Stacked geochemical halos related to the deposit are confined to the lower plate of the Roberts Mountains thrust and include two horizons of Hg, Cu, and Zn anomalies-as much as 180 m above the deposit-that mostly result from mercurian sphalerite. Extremely subtle indications of mineralization in the upper plate of the Roberts Mountains thrust above the deposit include arsenopyrite overgrowths on small pyrite crystals in 50- to 75-??m-wide clay-carbonate veinlets that lack alteration halos, arsenical rims on small disseminated crystal of recrystallized diagenetic pyrite, and partial replacement of diagenetic pyrite by tennantite. Some of these minerals contain anomalously high Au. However, these As-(Au)-bearing rocks most likely represent another locus of largely untested mineralized rock rather than distal halos related to either the Rodeo Creek or the nearby Dee and Storm gold deposits. Application of micromineralogic techniques helped to identify mineral assemblages that are specific to mineralization and provided an empirical foundation for interpretations of geochemical halos in the Carlin trend. District-scale geochemical patterns of several elements in stream sediments and surface rocks coincide with the northernmost Carlin trend and can be used to explore for Carlin-type deposits. Concentrations of elevated As and Sb in stream sediments (as much as 54 ppm As) have northwest-elongate lobate patterns that clearly outline the trend across a width of approximately 4 km. Arsenic contents of exposed rocks (as much as 90 ppm As) strongly correlate with As contents of derivative stream sediments, and rock contents of Sb show a somewhat lesser but nonetheless strong and similar correspondence. Factor analysis of stream-sediment data shows that those factor scores that are correlated with As, Sb, Au, and Pb also are high along the trend and suggest that mineralized rocks may be present. Although As was not detected by scanning electron microscope-energy dispersive spectrometer (SEM-EDS) studies in heavy mineral concentrates of high-As stream sediments in the Carlin trend, X-ray absorption near-edge spectra (XANES) of selected light fractions of stream sediment samples indicate that Al-bearing phases, such as gibbsite, amorphous Al oxyhydroxides, or aluminosilicate clay minerals host most of the As(V). The best fit, visually and in terms of the lowest residual, was obtained by a model compound of As(V) sorbed to gibbsite. Thus, most As in stream sediments derived from altered rock within the Carlin trend apparently is contained in light fractions. The geochemical character of young, unconsolidated, postmineral deposits that cover mineralized rocks on the Carlin trend partly results from mineralized sources along the trend. Concentration of As in the Miocene Carlin Formation shows an exceptio

Crustal Structure of the Iran Region from In-Country and Ground-Truth Data

DTIC Science & Technology

2008-09-30

thickness in the region (e.g., Mokhtari et al., 2004), and these data will be utilized in our Pn tomography both as constraints and for validation of...Vergne, and M. Mokhtari (2006). Seismological evidence for crustal-scale thrusting in the Zagros mountain belt (Iran), Geophys. J Int. 166: 227-237...for understanding the deformation history of the Arabian-Eurasian collision. Geophvs. J. Int. 172: 1179-1187. Mokhtari , M., A. M. Farahbod, C. Lindholm

Structural controls on Carlin-type gold mineralization in the gold bar district, Eureka County, Nevada

USGS Publications Warehouse

Yigit, O.; Nelson, E.P.; Hitzman, M.W.; Hofstra, A.H.

2003-01-01

The Gold Bar district in the southern Roberts Mountains, 48 km northwest of Eureka, Nevada, contains one main deposit (Gold Bar), five satellite deposits, and other resources. Approximately 0.5 Moz of gold have been recovered from a resource of 1,639,000 oz of gold in Carlin-type gold deposits in lower plate, miogeoclinal carbonate rocks below the Roberts Mountains thrust. Host rocks are unit 2 of the Upper Member of the Devonian Denay Formation and the Bartine Member of the McColley Canyon Formation. Spatial and temporal relations between structures and gold mineralization indicate that both pre-Tertiary and Tertiary structures were important controls on gold mineralization. Gold mineralization occurs primarily along high-angle Tertiary normal faults, some of which are reactivated reverse faults of Paleozoic or Mesozoic age. Most deposits are localized at the intersection of northwest- and northeast-striking faults. Alteration includes decalcification, and to a lesser extent, silicification along high-angle faults. Jasperoid (pervasive silicification), which formed along most faults and in some strata-bound zones, accounts for a small portion of the ore in every deposit. In the Gold Canyon deposit, a high-grade jasperoid pipe formed along a Tertiary normal fault which was localized along a zone of overturned fault-propagation folds and thrust faults of Paleozoic or Mesozoic age.

Paleoseismology of a newly discovered scarp in the Yakima fold-and-thrust belt, Kittitas County, Washington

USGS Publications Warehouse

Barnett, Elizabeth A.; Sherrod, Brian L.; Norris, Robert; Gibbons, Douglas

2013-01-01

The Boylston Mountains anticlinal ridge is one of several that are cored by rocks of the Columbia River Basalt Group and, with the interceding synclinal valleys, constitute the Yakima fold-and-thrust belt of central Washington. Lidar data acquired from the U.S. Army's Yakima Training Center reveal a prominent, northwest-side-up, 65°- to 70°-trending, 3- to 4-meter-high scarp that cuts across the western end of the Boylston Mountains, perpendicular to the mapped anticline. The scarp continues to the northeast from the ridge on the southern side of Park Creek and across the low ridges for a total length of about 3 kilometers. A small stream deeply incises its flood plain where it projects across Johnson Canyon. The scarp is inferred to be late Quaternary in age based on its presence on the modern landscape and the incised flood-plain sediments in Johnson Canyon. Two trenches were excavated across this scarp. The most informative of the two, the Horned Lizard trench, exposed shallow, 15.5-Ma Grande Ronde Basalt, which is split by a deep, wide crack that is coincident with the base of the scarp and filled with wedges of silty gravels that are interpreted to represent at least two generations of fault colluvium that offset a buried soil.

Découverte d'un chevauchement d'âge quaternaire au sud de la Grande Kabylie (Algérie)

NASA Astrophysics Data System (ADS)

Boudiaf, Azzedine; Philip, Hervé; Coutelle, Alain; Ritz, Jean-François

1999-03-01

In the Maghreb, the southern border of the Kabylie (Algeria) mountains is considered as an aseismic region. The detailed study of the historical seismicity of this region shows moderate seismic activity (M 1 = 5.0) which is not coherent with the observed tectonic deformations. However, an analysis of the morphology on Landsat image, aerial photos and the topography shows Quaternary deformations in the southern side of the "Kabylie massifs" (Algeria). These deformations are interpreted as reactivation of Miocene thrust faults. The tectonic Quaternary scarps are more spectacular in the Bouira and Tazmalt region and might be associated with successive strong earthquakes (M = 7.0). Therefore, this major active thrust fault observed in this region, as in many intraplate regions, poses the problem of the long return period of seismic activity in this zone. Elsevier, Paris

Application of High Resolution Topography and Remote Sensing: Imagery to the Kinematics of Fold-and-Thrust Belts

NASA Technical Reports Server (NTRS)

Rubin, Charles

1997-01-01

This report summarizes one year of funding for NASA contract NAGW-3691, Application of High Resolution Topography and Remote Sensing: Imagery to the Kinematics of Fold-and-Thrust Belts. I never received year three from NASA. The funds were to support on going tectonic and topographic studies along the front of the central Transverse Ranges and expand the topographic studies to the north. Below are results from the first two years of actual funds that I received from NASA (see attached Federal Cash Transaction Reports). The main focus of this contract was to define and understand the major tectonic processes affecting the formation and evolution of the topography in convergent tectonic settings. The results will be used to test ongoing space-based geodetic measurements and will be compared with present-day seismicity in the central Transverse Ranges and adjacent basins. Two major factors that controls topography in active regions are (1) tectonic uplift due to fault-normal compression and (2) subsequent erosion. The central Transverse and Temblor Ranges are excellent regions for these focused topographic studies. The tectonic processes leading to the mountain building are relatively straightforward and thus are easy to model. Available evidence suggests that the topography in this region is relatively young, - 3.5 Ma or less. In addition,, erosional processes may be relatively easier to model compared to larger and more ancient mountain belts. For example, in larger mountain belts, topographic relief may cause significant orographic effects and high elevation may result in part of the topography located above snowline. Both factors complicate interpretation of erosional processes that may be controlled by elevation. Mountain ranges that are significantly older may have experienced a much wider variety of erosional or climatic conditions over their lifetime. While erosion rates have certainly not been consistent in the Transverse or Temblor ranges over its 3.5 Ma lifetime, we are sure that the region was spared the Pleistocene glaciation that affected parts of the Sierra Nevada Range.

A new Late Cretaceous paleomagnetic pole from the Adel Mountains, west central Montana

NASA Astrophysics Data System (ADS)

Gunderson, Jay A.; Sheriff, Steven D.

1991-01-01

North America's apparent polar wander path has been poorly defined between the mid-Cretaceous and Paleocene reference pole positions. Existing data allowed 13° of apparent polar motion over about 22 m.y. (87-65 Ma) roughly coinciding with the beginning of Laramide deformation (˜80 Ma). We report on a paleomagnetic study of the Adel Mountain Volcanic rocks to refine the North American apparent polar wander path for this interval. The shonkinite rocks of the Adel Mountain Volcanic field are on the eastern edge of the Cretaceous-Paleocene fold and thrust belt; some of these structures disturb the western edge of the volcanic pile. We obtained two new K-Ar dates from the Adel rocks. One date, on biotite ( from a shonkinite dike that crosscuts most of the volcanic rocks, is 71.2±2.7 Ma. The other, a whole rock date from a flow deep in the volcanic pile, is 81.1±3.5 Ma. We collected six to nine paleomagnetic samples from each of 34 sites in roadcuts and natural outcrops of flows, dikes, and laccoliths. Positive fold and conglomerate tests, along with alternating field and thermal demagnetization, indicate that our characteristic remanent directions are primary magnetizations acquired before Late Cretaceous to Paleocene thrust belt deformation. Averaging the virtual geomagnetic poles from 26 reliable sites, all of normal polarity, yields a paleopole at 82.2°N, 209.9°E (α95 = 6.80°, k = 18.38). This pole is concordant with the Paleocene reference pole (82.0°N, 170.2°E, α95 = 3.5°, k = 18.6 (Diehl et al., 1983)) and is 11.6° from the Globerman and Irving (1988) mid-Cretaceous pole at 71°N, 196°E. The youngest information in the Cretaceous stillstand pole is from the Niobrara Formation (Shive and Frerichs, 1974) at about 85-89 Ma. If we take the average age of the Adel Mountain Volcanics to be 76 Ma, then ˜12° of apparent polar motion occurred between 87 Ma and 76 Ma. Thus, rapid apparent polar motion correlates well with the onset of Laramide deformation.

Lateral ramps in the folded Appalachians and in overthrust belts worldwide; a fundamental element of thrust-belt architecture

USGS Publications Warehouse

Pohn, Howard A.

2000-01-01

Lateral ramps are zones where decollements change stratigraphic level along strike; they differ from frontal ramps, which are zones where decollements change stratigraphic level perpendicular to strike. In the Appalachian Mountains, the surface criteria for recognizing the subsurface presence of lateral ramps include (1) an abrupt change in wavelength or a termination of folds along strike, (2) a conspicuous change in the frequency of mapped faults or disturbed zones (extremely disrupted duplexes) at the surface, (3) long, straight river trends emerging onto the coastal plain or into the Appalachian Plateaus province, (4) major geomorphic discontinuities in the trend of the Blue Ridge province, (5) interruption of Mesozoic basins by cross-strike border faults, and (6) zones of modern and probable ancient seismic activity. Additional features related to lateral ramps include tectonic windows, cross-strike igneous intrusions, areas of giant landslides, and abrupt changes in Paleozoic sedimentation along strike. Proprietary strike-line seismic-reflection profiles cross three of the lateral ramps that were identified by using the surface criteria. The profiles confirm their presence and show their detailed nature in the subsurface. Like frontal ramps, lateral ramps are one of two possible consequences of fold-and-thrust-belt tectonics and are common elements in the Appalachian fold-and-thrust belt. A survey of other thrust belts in the United States and elsewhere strongly suggests that lateral ramps at depth can be identified by their surface effects. Lateral ramps probably are the result of thrust sheet motion caused by continued activation of ancient cratonic fracture systems. Such fractures localized the transform faults along which the continental segments adjusted during episodes of sea-floor spreading.

Landform Evolution of the Zanskar Valley, Ladakh Himalaya.

NASA Astrophysics Data System (ADS)

Chahal, P.; Kumar, A.; Sharma, P.; Sundriyal, Y.; Srivastava, P.

2017-12-01

Zanskar River flow from south-west to north-east, perpendicularly through Higher Himalayan crystalline sequences, Tethyan sedimentary sequences, and Indus Molasses; and finally merge with the Indus River at Nimu. Geologically, the Indus valley is bounded by Ladakh Batholith in the north and highly folded and thrusted Zanskar mountain ranges in the south. Sedimentary sequences of Zanskar ranges are largely of continental origin, which were uplifted and deformed via several north verging thrusts, where Zanskar counter thrust, Choksti and Indus-Bazgo thrusts are important thrust zone, and there is atleast 36 km of crustal shortening in the Zanskar section which continued from middle Miocene to the late Pleistocene. This shortening is accommodated mainly by north or north-east directed Zanskar backthrusts. Two major tributaries of Zanskar: Tsrapchu and Doda, flow in the headwaters, along the strike of South Tibetan Detachment System (STDs), an east-west trending regional fault. The present study incorporate field sedimentology, geomorphology and chronology of landform associated with Zanskar valley. In the upper Zanskar, alluvial fan, valley fill and strath terraces configured the major landforms with paleo-lake deposits­­­ in the area between the fans. The lower catchment, at the confluence of Zanskar and Indus rivers, exhibit mainly valley fill terraces and strath terraces. Chronology suggests diachronous aggradation in the upper and lower Zanskar catchments. In the upper Zanskar large scale valley aggradation took place with simultaneously fan progradation and flooding events from 45-15 ka. Luminescence chronology of the lower Zanskar indicates aggradation from 145-55 ka and 18-12 ka. The two aggradation basins are separated by a deep V-shaped gorge which is approximately 60 km long. The longitudinal profile of the Zanskar River shows several local convexities marking knick point zone, which suggests tectonically controlled topography.

Late Cenozoic transpressional mountain building directly north of the Altyn Tagh Fault in the Sanweishan and Nanjieshan, North Tibetan Foreland, China

NASA Astrophysics Data System (ADS)

Cunningham, Dickson; Zhang, Jin; Li, Yanfeng

2016-09-01

For many tectonicists, the structural development of the northern Tibetan Plateau stops at the Altyn Tagh Fault (ATF). This study challenges that assumption. Structural field observations and remote sensing analysis indicate that the Sanweishan and Nanjieshan basement cored ridges of the Archean Dunhuang Block, which interrupt the north Tibetan foreland directly north of the ATF, are bound and cut by an array of strike-slip, thrust and oblique-slip faults that have been active in the Quaternary and remain potentially active. The Sanweishan is a SE-tilted block that is bound on its NW margin by a steep south-dipping thrust fault that has also accommodated sinistral strike-slip displacements. The Nanjieshan consists of parallel, but offset basement ridges that record NNW and SSE thrust displacements and sinistral strike-slip. Regional folds characterize the extreme eastern Nanjieshan and appear to have formed above blind thrust faults which break the surface further west. Previously published magnetotelluric data suggest that the major faults of the Sanweishan and Nanjieshan ultimately root to the south within conductive zones that are inferred to merge into the ATF. Therefore, although the southern margin of the Dunhuang Block focuses significant deformation along the ATF, the adjacent cratonic basement to the north is also affected. Collectively, the ATF and structurally linked Sanweishan and Nanjieshan fault array represent a regional asymmetric half-flower structure that is dominated by non-strain partitioned sinistral transpression. The NW-trending Dengdengshan thrust fault system near Yumen City appears to define the northeastern limit of the Sanweishan-Nanjieshan block, which may be regionally viewed as the most northern, but early-stage expression of Tibetan Plateau growth into a slowly deforming, mechanically stiff Archean craton.

Dynamics of erosion in a compressional mountain range revealed by 10Be paleoerosion rates

NASA Astrophysics Data System (ADS)

Val, P.; Hoke, G. D.; Fosdick, J. C.; Wittmann, H.

2015-12-01

The temporal evolution of erosion over million-year timescales is key to understanding the evolution of mountain ranges and adjacent fold-and-thrust belts. While models of orogenic wedge evolution predict an instantaneous response of erosion to pulses of rock uplift, stream-power based landscape evolution models predict catchment-wide erosion maxima that lag behind a rock uplift pulse. Here, we explore the relationships between rock uplift, erosion, and sediment deposition in the Argentine Precordillera fold-and-thrust belt at 30°S where extensive previous work documents deformation, climate and sediment accumulation histories. Sandstone samples spanning 8.8 to 1.8 Ma were collected from the previously dated wedge-top (Iglesia) and foredeep basins (Bermejo) for quartz purification and 10Be extraction. 10Be concentrations due to burial and exhumation were estimated and subtracted from the measured concentrations and yielded the inherited 10Be concentrations, which were then corrected for sample magnetostratigraphic age. The inherited concentrations were then used to calculate paleoerosion rates. We modeled various pre-burial and post-burial exposure scenarios in order to assess potential sources of uncertainty in the recovered paleoerosion rates. The modeling results reveal that pre-burial and post-burial exposure periods only marginally affect our results. By combining the 10Be-derived paleoerosion rates and geomorphic observations with detrital zircon provenance, we document the isolation of the wedge-top basin, which was later reconnected by an upstream migrating pulse of erosion in a process that was directly controlled by thrust activity and base level. The data further indicate that the attainment of maximum upland erosion rates lags maximum rates of deformation and subsidence over million-year timescales. The magnitudes and causes of the erosional delays shed new light on the catchment erosional response to tectonic deformation and rock uplift in orogenic wedges.

Fold-Thrust mapping using photogrammetry in Western Champsaur basin, SE France

NASA Astrophysics Data System (ADS)

Totake, Y.; Butler, R.; Bond, C. E.

2016-12-01

There is an increasing demand for high-resolution geometric data for outcropping geological structures - not only to test models for their formation and evolution but also to create synthetic seismic visualisations for comparison with subsurface data. High-resolution 3D scenes reconstructed by modern photogrammetry offer an efficient toolbox for such work. When integrated with direct field measurements and observations, these products can be used to build geological interpretations and models. Photogrammetric techniques using standard equipment are ideally suited to working in the high mountain terrain that commonly offers the best outcrops, as all equipment is readily portable and, in the absence of cloud-cover, not restricted to the meteorological and legal restrictions that can affect some airborne approaches. The workflows and approaches for generating geological models utilising such photogrammetry techniques are the focus of our contribution. Our case study comes from SE France where early Alpine fore-deep sediments have been deformed into arrays of fold-thrust complexes. Over 1500m vertical relief provides excellent outcrop control with surrounding hillsides providing vantage points for ground-based photogrammetry. We collected over 9,400 photographs across the fold-thrust array using a handheld digital camera from 133 ground locations that were individually georeferenced. We processed the photographic images within the software PhotoScan-Pro to build 3D landscape scenes. The built photogrammetric models were then imported into the software Move, along with field measurements, to map faults and sedimentary layers and to produce geological cross sections and 3D geological surfaces. Polylines of sediment beds and faults traced on our photogrammetry models allow interpretation of a pseudo-3D geometry of the deformation structures, and enable prediction of dips and strikes from inaccessible field areas, to map the complex geometries of the thrust faults and deformed strata in detail. The resultant structural geometry of the thrust zones delivers an exceptional analogue to inaccessible subsurface fold-thrust structures which are often challenging to obtain a clear seismic image.

Geologic and Fossil Locality Maps of the West-Central Part of the Howard Pass Quadrangle and Part of the Adjacent Misheguk Mountain Quadrangle, Western Brooks Range, Alaska

USGS Publications Warehouse

Dover, James H.; Tailleur, Irvin L.; Dumoulin, Julie A.

2004-01-01

The map depicts the field distribution and contact relations between stratigraphic units, the tectonic relations between major stratigraphic sequences, and the detailed internal structure of these sequences. The stratigraphic sequences formed in a variety of continental margin depositional environments, and subsequently underwent a complexde formational history of imbricate thrust faulting and folding. A compilation of micro and macro fossil identifications is included in this data set.

Non-cylindrical fold growth in the Zagros fold and thrust belt (Kurdistan, NE-Iraq)

NASA Astrophysics Data System (ADS)

Bartl, Nikolaus; Bretis, Bernhard; Grasemann, Bernhard; Lockhart, Duncan

2010-05-01

The Zagros mountains extends over 1800 km from Kurdistan in N-Iraq to the Strait of Hormuz in Iran and is one of the world most promising regions for the future hydrocarbon exploration. The Zagros Mountains started to form as a result of the collision between the Eurasian and Arabian Plates, whose convergence began in the Late Cretaceous as part of the Alpine-Himalayan orogenic system. Geodetic and seismological data document that both plates are still converging and that the fold and thrust belt of the Zagros is actively growing. Extensive hydrocarbon exploration mainly focuses on the antiforms of this fold and thrust belt and therefore the growth history of the folds is of great importance. This work investigates by means of structural field work and quantitative geomorphological techniques the progressive fold growth of the Permam, Bana Bawi- and Safeen- Anticlines located in the NE of the city of Erbil in the Kurdistan region of Northern Iraq. This part of the Zagros fold and thrust belt belongs to the so-called Simply Folded Belt, which is dominated by gentle to open folding. Faults or fault related folds have only minor importance. The mechanical anisotropy of the formations consisting of a succession of relatively competent (massive dolomite and limestone) and incompetent (claystone and siltstone) sediments essentially controls the deformation pattern with open to gentle parallel folding of the competent layers and flexural flow folding of the incompetent layers. The characteristic wavelength of the fold trains is around 10 km. Due to faster erosion of the softer rock layers in the folded sequence, the more competent lithologies form sharp ridges with steeply sloping sides along the eroded flanks of the anticlines. Using an ASTER digital elevation model in combination with geological field data we quantified 250 drainage basins along the different limbs of the subcylindrical Permam, Bana Bawi- and Safeen- Anticlines. Geomorphological indices of the drainage basins (spacing and elongation ratio, circularity index and shape factor) of different parts in the fore and back-limb of the anticlines demonstrate that the basins have a low maturity and that fold growth is still highly active. Most importantly, the results of this geomorphological investigations demonstrates that the subcylindrical folds have developed from several non-cylindrical embryonic folds, which have merged during progressive fold growth.

Paleomagnetic Results for Eocene Volcanic Rocks from Northeastern Washington and the Tertiary Tectonics of the Pacific Northwest

NASA Astrophysics Data System (ADS)

Fox, Kenneth F., Jr.; Beck, Myrl E., Jr.

1985-04-01

The direction of remanent magnetization for 102 sites in Eocene volcanic and volcaniclastic rocks of the O'Brien Creek Formation, Sanpoil Volcanics, and Klondike Mountain Formation suggests approximately 25° of clockwise rotation of a 100 by 200 km area in northeastern Washington. The volcanic rocks consist chiefly of rhyodacite and quartz latite flows, with intercalated ash flow tuff and volcaniclastic layers. These rocks have been sampled at 102 sites distributed among five volcanotectonic depressions: the Toroda Creek, Republic, Keller, and First Thought grabens and the Spokane-Enterprise lineament. The volcanic rocks probably range in age from 55 m.y. to about 48 m.y., and the 50- to 48-m.y.-old volcanic rocks within this suite appear to be rotated as much as the older rocks. Previous investigators have shown that 40-m.y.-old and younger plutonic rocks of northwestern Washington are not rotated; hence we infer that the north-central Washington rocks were rotated to their present declination between 48 and 40 m.y. B.P. (during the middle and/or late Eocene). During early Eocene time this region was extended in a westward direction through crustal necking, gneiss-doming, diking, and graben formation. Internal deformation of the region related to this crustal extension was extreme, but most bedrock units that were formed concurrent with the crustal extension were probably in place prior to the rotation; hence we infer that the rotation was chiefly accommodated by movement on faults peripheral to the sampled area. Faults active during Paleogene time appear to define boundaries of a triangular crustal block (the Sanpoil block), encompassing much of northeastern Washington, northern Idaho, northwestern Montana, and adjacent parts of British Columbia. The faults include the Laramide thrusts of the Rocky Mountain thrust belt, the strike-slip faults of the Lewis and Clark line, and strike-slip faults of the Straight Creek-Fraser zone. We suggest that during early Eocene time the Sanpoil block was extended westward through crustal necking and dilation and then during the middle Eocene was rotated clockwise and thrust over the craton in a final stage of Laramide thrusting. The "motor" driving these deformations presumably was interaction of North America with oceanic lithosphere off its western margin; such interaction probably involved right-oblique underthrusting and dextral shear.

Deformation Front Development at the Northeast Margin of the Tainan Basin, Tainan-Kaohsiung Area, Taiwan

NASA Astrophysics Data System (ADS)

Huang, Shiuh-Tsann; Yang, Kenn-Ming; Hung, Jih-Hao; Wu, Jong-Chang; Ting, Hsin-Hsiu; Mei, Wen-Wei; Hsu, Shiang-Horng; Lee, Min

2004-03-01

The geological setting south of the Tsengwen River and the Tsochen Fault is the transitional zone between the Tainan foreland basin and Manila accretionary wedge in Southwestern Taiwan. This transitional zone is characterized by the triangle zone geological model associated with back thrusts that is quite unique compared to the other parts of the Western foreland that are dominated by thrust imbrications. The Hsinhua structure, the Tainan anticline, and the offshore H2 anticline are the first group of major culminations in the westernmost part of the Fold-and-Thrust belt that formed during the Penglay Orogeny. Structures in the the Tainan and Kaohsiung areas provide important features of the initial mountain building stage in Western Taiwan. A deeply buried basal detachment with ramp-flat geometry existed in the constructed geological sections. A typical triangle is found by back thrusting, such as where the Hsinhua Fault cuts upsection of the Upper Pliocene and Pleistocene from a lower detachment along the lower Gutingkeng Formation. The Tainan structure is a southward extension of the Hinhua Fault and has an asymmetric geometry of gentle western and steep eastern limbs. Our studies suggest that the Tainan anticline is similar to the structure formed by the Hsinhua Fault. Both are characterized by back thrusts and rooted into a detachment about 5 km deep. The triangle zone structure stops at H2 anticline offshore Tainan and beyond the west of it, All the structures are replaced by rift tectonic settings developed in the passive continental margin. On the basal detachment, a major ramp interpreted as a tectonic discontinuity was found in this study. Above the northeastern end of the major ramp of basal detachment, the Lungchuan Fault is associated with a triangle system development, while at the southwestern end a thrust wedge is present. It could be deduced that a thrust wedge intrudes northwestward. The area below the major ramp, or equivalent to the trailing edge of the basal detachment, mud diapers often occur in relation to the thickest deposits of the Gutingkeng Formation and caused by the mechanism of detachment folding

Kinematics and Seismotectonics of the Montello Thrust Fault (Southeastern Alps, Italy) Revealed by Local GPS and Seismic Networks

NASA Astrophysics Data System (ADS)

Serpelloni, E.; Anderlini, L.; Cavaliere, A.; Danesi, S.; Pondrelli, S.; Salimbeni, S.; Danecek, P.; Massa, M.; Lovati, S.

2014-12-01

The southern Alps fold-and-thrust belt (FTB) in northern Italy is a tectonically active area accommodating large part of the ~N-S Adria-Eurasia plate convergence, that in the southeastern Alps ranges from 1.5 to 2.5 mm/yr, as constrained by a geodetically defined rotation pole. Because of the high seismic hazard of northeastern Italy, the area is well monitored at a regional scale by seismic and GPS networks. However, more localized seismotectonic and kinematic features, at the scale of the fault segments, are not yet resolved, limiting our knowledge about the seismic potential of the different fault segments belonging to the southeastern Alps FTB. Here we present the results obtained from the analysis of data collected during local seismic and geodetic experiments conducted installing denser geophysical networks across the Montello-Bassano-Belluno system, a segment of the FTB that is presently characterized by a lower sismicity rate with respect to the surrounding domains. The Montello anticline, which is the southernmost tectonic features of the southeastern Alps FTB (located ~15 km south of the mountain front), is a nice example of growing anticline associated with a blind thrust fault. However, how the Adria-Alps convergence is partitioned across the FTB and the seismic potential of the Montello thrust (the area has been struck by a Mw~6.5 in 1695 but the causative fault is still largely debated) remained still unresolved. The new, denser, GPS data show that this area is undergoing among the highest geodetic deformation rates of the entire south Alpine chain, with a steep velocity gradient across the Montello anticline. The earthquakes recorded during the experiment, precisely relocated with double difference methods, and the new earthquake focal mechanisms well correlate with available information about sub-surface geological structures and highlight the seismotectonic activity of the Montello thrust fault. We model the GPS velocities using elastic dislocations embedded in a kinematic block model approach, which suggest that the Montello thrust fault is weakly coupled with respect to surrounding segments of the southernmost thrust system. Future works will include the integration of InSAR data and the densification/improvement of the geodetic infrastructure.

Reconnaissance geology of the Central Mastuj Valley, Chitral State, Pakistan

USGS Publications Warehouse

Stauffer, Karl W.

1975-01-01

The Mastuj Valley in Chitral State is a part of the Hindu Kush Range, and is one of the structurally most complicated areas in northern Pakistan. Sedimentary rocks ranging from at least Middle Devonian to Cretaceous, and perhaps Early Tertiary age lie between ridge-forming granodiorite intrusions and are cut by thrust faults. The thrust planes dip 10? to 40? to the north- west. Movement of the upper thrust plates has been toward the southeast relative to the lower blocks. If this area is structurally typical of the Hindu-Kush and Karakoram Ranges, then these mountains are much more tectonically disturbed than previously recorded, and suggest compression on a scale compatible with the hypothesis that the Himalayan, Karakoram, and Hindu Kush Ranges form part of a continental collision zone. The thrust faults outline two plates consisting of distinctive sedimentary rocks. The lower thrust plate is about 3,000 feet thick and consists of the isoclinally folded Upper Cretaceous to perhaps lower Tertiary Reshun Formation. It has overridden the Paleozoic metasedimentary rocks of the Chitral Slate unit. This thrust plate is, in turn, overridden by an 8,000-foot thick sequence consisting largely of Devonian to Carboniferous limestones and quartzites. A key factor in the tectonic processes has been the relatively soft and plastic lithology of the siltstone layers in the Reshun Formation which have acted as lubricants along the principal thrust faults, where they are commonly found today as fault slices and smears. The stratigraphic sequence, in the central Mastuj Valley was tentatively divided into 9 mapped units. The fossiliferous shales and carbonates of the recently defined Shogram Formation and the clastlcs of the Reshun Formation have been fitted into a sequence of sedimentary rocks that has a total thick- ness of at least 13,000 feet and ranges in age from Devonian to Neogene. Minerals of potential economic significance include antimony sulfides which have been mined elsewhere in Chitral, the tungstate, scheelite, which occurs in relatively high concentrations in heavy-mineral fractions of stream sands, and an iron-rich lateritic rock.

Paleomagnetism of the Wyoming Craton: A Pre-Laurentian Puzzle

NASA Astrophysics Data System (ADS)

Kilian, T.; Chamberlain, K.; Mitchell, R. N.; Evans, D. A.; Bleeker, W.; Lecheminant, A. N.

2010-12-01

The Archean Wyoming craton is mostly buried beneath Phanerozoic sediments in the Rocky Mountains of the west central United States. Exposures of the craton are entirely in thrust-bounded Laramide uplifts and contain numerous swarms of Neoarchean-Proterozoic mafic dikes. U-Pb ages from these dikes include ~2685 Ma from a dike in the Owl Creek Mountains (Frost et al., 2006) as well as another in the Bald Mountain region of the Bighorn Mountains (this study), ~2170 Ma from the Wind River Mountain quartz diorite (Harlan et al., 2003), ~2110 Ma from a dike in the Granite Mountains (Bowers and Chamberlain, 2006), ~2010 Ma from a Kennedy dike in the Laramie Range (Cox et al., 2000), and ~780 Ma for dikes in the Beartooth and Teton Mountains (Harlan et al., 1997). These possible age ranges of magmatic events will allow a detailed comparison with other cratons, especially Superior and Slave. Prior to the assembly of Laurentia, Wyoming may have been connected with Slave in supercraton Sclavia (Bleeker, 2003; Frost et al., 2007), or alternatively, Wyoming may have been attached to the present southern margin of Superior in the supercraton Superia, as judged by similarities of the thrice-glaciated Huronian and Snowy Pass sedimentary successions (Roscoe and Card, 1993). Paleomagnetic results will be presented from over 150 dikes in the Wyoming craton. All dikes were from the basement uplifts of the Beartooth Mountains, Bighorn Mountains, Owl Creek Mountains, Granite Mountains, Ferris Mountains and Laramie Range. Dikes range in widths from 1 to >100 meters, and trends vary across all orientations. Stable remanence is observed in majority of sites with at least 8 different directions from the various uplifts. Structural corrections are applied when necessary to restore shallowly dipping Cambrian strata to horizontal. The paleomagnetic study is being integrated with precise U-Pb geochronology of dikes that bear stable remanence directions. Results will eventually allow a comparison of results from both Slave and Superior cratons throughout the Archean and Proterozoic. The data will test the prior connections, or lack thereof, among the Archean cratons in Laurentia, and help assess whether there was a supercontinent during the Archean-Proterozoic transition.

Preliminary Geologic Map of the Little Piute Mountains, California; a Digital Database

USGS Publications Warehouse

Howard, Keith A.; Dennis, Michael L.; Karlstrom, Karl; Phelps, Geoffrey A.

1997-01-01

Introduction The Little Piute Mountains in the eastern Mojave Desert expose a series of folds and thrust faults involving metamorphosed Paleozoic strata (Miller and others, 1982; Stone and others, 1983). Detailed mapping of these structures was undertaken to help elucidate regional Mesozoic structural evolution. Earlier geologic maps were prepared by Cooksley (1960a,b,c,d, generalized by Bishop, 1964) and Stone and others (1983). Deformed and metamorphosed Paleozoic and Triassic rocks form a stratal succession that was originally deposited in shallow seas on the North American craton. Based on lithologic sequence the units are correlated with unmetamorphosed equivalents 200 km to the northeast in the Grand Canyon, Arizona, and 35-50 km to the west in the Marble, Ship, and Providence Mountains, California (Stone and others, 1983). The Paleozoic sequence rests nonconformably on a heterogeneous basement of polydeformed Early Proterozoic gneiss (Miller and others, 1982; Wooden and Miller, 1990). Triassic and older rocks were deformed, metamorphosed to staurolite or andalusite grade, and intruded concordantly at their base by Late Cretaceous granodiorite (Miller and others, 1982).

Preliminary Geologic Map of the the Little Piute Mountains, San Bernardino County, California

USGS Publications Warehouse

Howard, Keith A.; Dennis, Michael L.; Karlstrom, Karl E.; Phelps, Geoffrey A.

1995-01-01

Introduction The Little Piute Mountains in the eastern Mojave Desert expose a series of folds and thrust faults involving metamorphosed Paleozoic strata (Miller and others, 1982; Stone and others, 1983). Detailed mapping of these structures was undertaken to help elucidate regional Mesozoic structural evolution. Earlier geologic maps were prepared by Cooksley (1960a,b,c,d, generalized by Bishop, 1964) and Stone and others (1983). Deformed and metamorphosed Paleozoic and Triassic rocks form a stratal succession that was originally deposited in shallow seas on the North American craton. Based on lithologic sequence the units are correlated with unmetamorphosed equivalents 200 km to the northeast in the Grand Canyon, Arizona, and 35-50 km to the west in the Marble, Ship, and Providence Mountains, California (Stone and others, 1983). The Paleozoic sequence rests nonconformably on a heterogeneous basement of polydeformed Early Proterozoic gneiss (Miller and others, 1982; Wooden and Miller, 1990). Triassic and older rocks were deformed, metamorphosed to staurolite or andalusite grade, and intruded concordantly at their base by Late Cretaceous granodiorite (Miller and others, 1982).

Synthrusting deposition of the Pennsylvanian and Permian Strathearn Formation, Northern Carlin Trend, Nevada

USGS Publications Warehouse

Theodore, T.G.; Berger, V.I.; Singer, D.A.; Harris, A.G.; Stevens, C.H.

2004-01-01

The middle Upper Pennsylvanian and middle Lower Permian Strathearn Formation belongs to the overlap assemblage of the Antler orogen in Nevada. At Beaver Peak, near the Carlin Trend of gold deposits, it contains synorogenic conglomerate deposits associated with emplacement of a regionally extensive, 1-km-thick tectonic wedge that is floored by the Coyote thrust. Normal marine conodont biofacies throughout the Strathearn Formation suggest middle shelf or deeper, depositional environments. The allochthon floored by the Coyote thrust has been thrust above a middle Upper Pennsylvanian, lower conglomerate unit of the Strathearn Formation. A middle Lower Permian upper conglomerate unit, the highest unit recognized in the Strathearn Formation, as well as similarly aged dolomitic siltstone, onlap directly onto Ordovician quartzarenite of the Vinini Formation that makes up most of the Coyote allochthon. Quartz grains and quartzarenite fragments of variable roundness and shape in the conglomerate units were derived from the presently adjoining tectonic lobe of mostly quartzarenite that advanced southeast (present geographic coordinates) during the late Paleozoic into the developing Strathearn basin. Chert fragments in the conglomerates probably were derived mostly from Devonian Slaven Chert, including a widespread thick me??lange unit of the Slaven Chert in the footwall of the Coyote thrust.Lithologic and shape ratio data from approximately 4200 clasts at 17 sites of the two major conglomerate units in the Strathearn Formation at Beaver Peak are roughly similar in that they contain only chert and quartzarenite clasts, and chert clasts predominate in both units. They differ in the relative proportion of the two lithologies whereby quartzarenite clasts increase sixfold in the upper unit (middle Lower Permian) versus its content in the lower conglomerate unit. Relations at the unconformity between the upper conglomerate unit and its underlying quartzarenite shows quartzarenite fragments actually breaking away from an immediately subjacent source. Ordovocian quartzarenite, which forms a tectonically uplifted wedge with the Coyote thrust at its base, became a source region for much of the quartzarenite detritus deposited preferentially in the upper parts of the Strathearn Formation. The conglomerate units of the Strathearn Formation temporally bracket emplacement of the Coyote thrust. Thrusting related to contractional reactivation of the Robert Mountains thrust system largely was completed by middle Early Permian. ?? 2004 Published by Elsevier B.V.

Upper crustal mechanical stratigraphy and the evolution of thrust wedges: insights from sandbox analogue experiments

NASA Astrophysics Data System (ADS)

Milazzo, Flavio; Storti, Fabrizio; Nestola, Yago; Cavozzi, Cristian; Magistroni, Corrado; Meda, Marco; Salvi, Francesca

2016-04-01

Crustal mechanical stratigraphy i.e. alternating mechanically weaker and stronger layers within the crust, plays a key role in determining how contractional deformations are accommodated at convergent plate boundaries. In the upper crust, evaporites typically provide preferential décollement layers for fault localization and foreland ward propagation, thus significantly influencing evolution of thrust-fold belts in terms of mechanical balance, geometries, and chronological sequences of faulting. Evaporites occur at the base of many passive margin successions that underwent positive inversion within orogenic systems. They typically produce salient geometries in deformation fronts, as in the Jura in the Northern Alps, the Salakh Arch in the Oman Mountains, or the Ainsa oblique thrust-fold belt in the Spanish Pyrenees. Evaporites frequently occur also in foredeep deposits, as in the Apennines, the Pyrenees, the Zagros etc. causing development of additional structural complexity. Low-friction décollement layers also occur within sedimentary successions involved in thrust-fold belts and they contribute to the development of staircase fault trajectories. The role of décollement layers in thrust wedge evolution has been investigated in many experimental works, particularly by sandbox analogue experiments that have demonstrated the impact of basal weak layers on many first order features of thrust wedges, including the dominant fold vergence, the timing of fault activity, and the critical taper. Some experiments also investigated on the effects of weak layers within accreting sedimentary successions, showing how this triggers kinematic decoupling of the stratigraphy above and below the décollements, thus enhancing disharmonic deformation. However, at present a systematic experimental study of the deformation modes of an upper crustal mechanical stratigraphy consisting of both low-friction and viscous décollement layers is still missing in the specific literature. In this contribution we present the results of such a study, where a three-décollement mechanical stratigraphy has been deformed in the sandbox at the same boundary conditions. Different rheological properties were assigned to the three décollements in different experiments, up to testing all possible mechanical stratigraphies. Implications on thrust propagation and slip rate history and cross-sectional thrust wedge architecture are discussed and compared with natural cases.

Reconciling deep seismic refraction and reflection data from the grenvillian-appalachian boundary in western New England

USGS Publications Warehouse

Hughes, S.; Luetgert, J.H.; Christensen, N.I.

1993-01-01

The Grenvillian-Appalachian boundary is characterized by pervasive mylonitic deformation and retrograde alteration of a suite of imbricated allochthonous and parautochthonous gneisses that were thrust upon the Grenvillian continental margin during the lower Paleozoic. Seismic reflection profiling across this structural boundary zone reveals prominent dipping reflectors interpreted as overthrust basement slices (parautochthons) of the Green Mountain Anticlinorium. In contrast, a seismic refraction study of the Grenvillian-Appalachian boundary reveals a sub-horizontally layered seismic velocity model that is difficult to reconcile with the pronounced sub-vertical structures observed in the Green mountains. A suite of rock samples was collected from the Green Mountain Anticlinorium and measured at high pressures in the laboratory to determine the seismic properties of these allochthonous and parautochthonous gneisses. The laboratory-measured seismic velocities agree favorably with the modelled velocity structure across the Grenvillian-Appalachian boundary suggesting that the rock samples are reliable indicators of the rock mass as whole. Samples of the parautochthonous Grenvillian basement exposed in the Green Mountains have lower velocities, by about 0.5 km/s, than lithologically equivalent units exposed in the eastern Adirondack Highlands. Velocity reduction in the Green Mountain parautochthons can be accounted for by retrograde metamorphic alteration (hydration) of the paragneisses. Seismic anisotropies, ranging from 2 to 12%, in the mylonitized Green Mountain paragneisses may also contribute to the observation of lower seismic velocities, where the direction of ray propagation is normal to the foliation. The velocity properties of the Green Mountain paragneisses are thus insufficiently different from the mantling Appalachian allochthons to permit their resolution by the Ontario-New York-New England seismic refraction profile. ?? 1993.

Paleozoic-involving thrust array in the central Sierras Interiores (South Pyrenean Zone, Central Pyrenees): regional implications

NASA Astrophysics Data System (ADS)

Rodriguez, L.; Cuevas, J.; Tubía, J. M.

2012-04-01

This work deals with the structural evolution of the Sierras Interiores between the Tena and Aragon valleys. The Sierras Interiores is a WNW-trending mountain range that bounds the South Pyrenean Zone to the north and that is characterized by a thrust-fold system with a strong lithological control that places preferably decollements in Triassic evaporites. In the studied area of the Sierras Interiores Cenomanian limestones cover discordantly the Paleozoic rocks of the Axial Zone because there is a stratigraphic lacuna developed from Triassic to Late Cretaceous times. A simple lithostratigraphy of the study area is made up of Late Cenomanian to Early Campanian limestones with grey colour and massive aspect in landscape (170 m, Lower calcareous section), Campanian to Maastrichtian brown coloured sandstones (400-600 m, Marboré sandstones) and, finally, Paleocene light-coloured massive limestones (130-230 m), that often generate the higher topographic levels of the Sierras Interiores due to their greater resistance to erosion. Above the sedimentary sequence of the Sierras Interiores, the Jaca Basin flysch succession crops out discordantly. Based on a detailed mapping of the studied area of the Sierras Interiores, together with well and structural data of the Jaca Basin (Lanaja, 1987; Rodríguez and Cuevas, 2008) we have constructed a 12 km long NS cross section, approximately parallel to the movement direction deduced for this region (Rodríguez et al., 2011). The main structure is a thrust array made up of at least four Paleozoic-involving thrusts (the deeper thrust system) of similar thickness in a probably piggyback sequence, some of which are blind thrusts that generate fold-propagation-folds in upper levels. The higher thrust of the thrust array crops out duplicating the lower calcareous section all over the Sierras Interiores. The emplacement of the deeper thrust system generated the tightness of previous structures: south directed piggyback duplexes (the upper thrust system) affecting the Marboré sandstones and the Paleocene limestones, deformed by angular south-vergent folds and their related axial plane foliation. The transect explained above clearly summarizes the alpine evolution of northern part of the Sierras Interiores. Moreover, well data available indicate the presence of two thrust soled in the lower calcareous section covering Triassic evaporites at 5 km depth and 8 km to the south of the Sierras Interiores. Because the Triassic evaporites constitute a main decollement level in the South Pyrenean Zone, the deeper thrust system is associated to the emplacement of the Gavarnie nappe. Lanaja, J.M., 1987, Contribución de la exploración petrolífera al conocimiento de la Geología de España, IGME, Madrid, 465 p. Rodríguez, L., Cuevas, J., 2008. Geogaceta 44, 51-54. Rodríguez, L., Cuevas, J., Tubia, J.M., 2011. Geophysical Research Abstracts 13, 2273.

Kinematic Evolution of the North-Tehran Fault (NTF), Alborz Mountains, Iran

NASA Astrophysics Data System (ADS)

Landgraf, A.; Ballato, P.; Strecker, M. R.; Shahpasandzadeh, M.; Friedrich, A.; Tabatabaei, S. H.

2007-12-01

The ENE-to NW-striking NTF is an active frontal thrust that delimits the Alborz Mountain range to the south with an up to 2000 m topographic break with respect to the adjacent Tehran plain. Eocene rocks of the Alborz range are thrusted over Neogene and Quaternary sediments of the alluvial Tehran embayment. The fault consists of right- stepping segments and merges to the east with the active Mosha-Fasham strike-slip fault (MFF). The complex tectonic history, involving changes in the direction of SHmax, has resulted in a composite tectonic landscape with inherited topographic and fault-kinematic fingerprints along the NTF. We therefore used a combination of fault-kinematic measurements and geomorphic observations to unravel the temporal tectonic evolution of this fault. Presently, the NTF is virtually inactive, although the tectonically overprinted landforms reflect tectonic activity on longer time scales during the Quaternary. Being located adjacent north of the Tehran megacity, there is thus considerable interest to decipher its youngest tectonic evolution and to better understand the relation with other fault systems. Our fault kinematic study has revealed an early dextral kinematic history for the NTF. Dextral strike-slip and oblique reverse faulting took place during NW-oriented shortening. The overall fault-geometry of the NTF suggests that it has evolved in relation to dextral transpression along the MFF. This early kinematic regime was superseded by NE-oriented shortening, associated with sinistral-oblique thrusting along the fault segments. Fault linkage between the semi-independent ENE-striking NTF-segments and NW-striking thrusts (Emamzadeh Davud Fault [EDF], Purkan Vardij Thrust [PVT], NTF-prolongation) point towards an evolution into a nascent transpressional duplex. In this scenario the NTF segments constitute lateral ramps and the NW-striking faults act as frontal ramps. Topographic residuals, as an expression of high-uplift zones, indicate that the central segment of the NTF, incorporating the EDF was most effective in accommodating oblique convergence during this time. However, subtle knickpoints in the longitudinal river profiles crossing the PVT may indicate a relatively recent transfer of deformation onto this block. The youngest manifestations of deformation along the NTF, however, are left-lateral and normal faulting. This youngest phase of activity is documented by numerous striated and rotated conglomeratic clasts, meter-scale fault gouge zones with shear-sense indicators of oblique normal faulting, and multiple colluvial wedges with drag phenomena. Rupture traces and filled extensional cracks reaching the surface also document the seismogenic nature of these features. Since recent left-lateral transtension is also known from neighboring faults, e.g., the eastern MFF, our observations suggest that this youngest phase of tectonic activity of the NTF is a regional phenomenon, rather than the result of locally-determined geometries.

Coseismic fold scarp associated with historic earthquakes upon the Yoro active blind thrust, the Nobi-Ise fault zone, central Japan

NASA Astrophysics Data System (ADS)

Ishiyama, T.; Mueller, K.; Togo, M.

2004-12-01

We present structural models constrained by tectonic geomorphology, surface geologic mapping, shallow borehole transects and a high-resolution S-wave seismic reflection profile to define the kinematic evolution of a coseismic fold scarp along the Nobi-Ise fault zone (NIFZ). The NIFZ is an active intraplate fault system in central Japan, and consists of a 110-km-long array of active, east-verging reverse faults. Fold scarps along the Yoro fault are interpreted as produced during a large historic blind-thrust earthquake. The Yoro Mountains form the stripped core of the largest structure in the NIFZ and expose Triassic-Jurassic basement that are thrust eastward over a 2-km-thick sequence of Pliocene-Pleistocene strata deposited in the Nobi basin. This basement-cored fold is underlain by an active blind thrust that is expressed as late Holocene fold scarps along its eastern flank. Drilling investigations across the fold scarp at a site near Shizu identified at least three episodes of active folding associated with large earthquakes on the Yoro fault. Radiocarbon ages constrain the latest event as having occurred in a period that contains historical evidence for a large earthquake in A.D. 1586. A high resolution, S-wave seismic reflection profile at the same site shows that the topographic fold scarp coincides with the projected surface trace of the synclinal axis, across which the buried, early Holocene to historic sedimentary units are folded. This is interpreted to indicate that the structure accommodated coseismic fault-propagation folding during the A.D. 1586 blind thrust earthquake. Flexural-slip folding associated with secondary bedding-parallel thrusts may also deform late Holocene strata and act to consume slip on the primary blind thrust across the synclinal axial surfaces. The best-fitting trishear model for folded ca. 13 ka gravels deposited across the forelimb requires a 28\\deg east-dipping thrust fault. This solution suggests that a 4.2 mm/yr of slip rate has been accommodated on the Yoro fault during the late Holocene, with an average vertical rate of 1.9 mm/yr. This is consistent with longer-term slip rates calculated by a structural relief across a ca. 7.3 ka volcanic ash horizon (1.6 mm/yr), and ca. 110 ka innerbay clays (1.3 mm/yr) deposited across the forelimb. Our trishear model is thus able to account for the bulk of the folding history accommodated at shorter millennial timescales, suggesting that this technique may be used to adequately define slip rates on blind thrust faults.

Lithospheric buckling and far-foreland deformation during the Laramide and Appalachian orogenies

NASA Astrophysics Data System (ADS)

Tikoff, B.; Siddoway, C. S.

2017-12-01

Major intraplate tectonics within North America (Laurentia) occurs during times of major orogenesis along the plate margins. During mountain building, typical structures of the hinterland are an orogenic plateau and fold-and-thrust belts, while in the far foreland (intraplate) areas long-wavelength ( 200 km or longer) folds and fault-reactivation features form. Long-wavelength folds are evident in both the Appalachian and Laramide orogenic forelands, with the stratigraphy recording the timing of the uplift. This contribution examines the model of lithospheric buckling - periodic folding associated with a horizontal endload on the edge of the plate - based on scaled, physical experiments and corroborated by numerical models. The Laramide (75-55 Ma) intraplate orogen in the classical location in Wyoming contains basement-cored arches spaced 200 km apart, for which the mechanism of uplift is questioned. Seismic evidence obtained for the Bighorn uplift, Wyoming, obtained by the EarthScope Bighorn project, shows an upwarp of the Moho beneath, but oblique to the trend of the surface exposure of the basement arch. Both the surface and Moho exhibit approximately the same structural relief. The seismic data exhibit no evidence for a regionally continuous decollement, nor is there evidence of rotation of structural markers within these features, of the type that is observed in the detached fold-and-thrust belt. The intraplate region affected by long-wavelength folding includes western Wyoming, with continuation of some features across the E-W-oriented Cheyenne belt (e.g., Rock Springs-Douglas Creek arch), Colorado Plateau, and High Plains east of the Rocky Mountains, where surface and subsurface structures display a series of anticlinal arches ("plains-type" folds). Appalachian mountain building also caused long-wavelength folding, with a spacing consistent with lithospheric buckling, mostly associated with the Devonian Acadian orogeny. The Laramide arches in the High Plains seem to occur on arches inherited from the Appalachian orogeny, suggesting the permanence of these lithospheric buckles once they have formed.

The petrology, structure and geochemistry of an Archean terrane in the North Snowy Block, Beartooth Mountains, Montana

NASA Astrophysics Data System (ADS)

Mogk, D. W.

1984-12-01

Six major rock units in the North Snowy Block in an Archean mobile belt are recognized between all units representing discontinuities in metamorphic grade, structural style, geochemistry, and isotopic ages. Four of the units occur in NE trending linear belts; the Basement Gneiss; the phyllitic Davis Creek Schist; the mount cowen augen gneis; the Paragneiss unit. Overlying the linear units is the 3.2 Ga old Pine Creek Nappe Complex, an isoclinally folded, middle to upper amphibolite facies, thrust nappe consisting of the Barney Creek Amphibolite, George Lake Marble and Jewel Quartzite. The highest structural units, including a thick sequence of upper amphibolite grade supracrustal rocks and a lower section of injected 3.4 Ga old granitic to tonalitic migmatitic rocks were emplaced on the Columbine Thrust. It is shown that there was secular variation in tectonic style in the Archean of southwest Montana. Three stages are recognized: (1) melting of ancient matic crust produced trondhjemitic continental nuclei; (2) numerous ensialic basins were created and destroyed, resulting in high grade metamorphism and mignatization of supracrustal rocks; and (3) contemporary style plate tectonics resulted in generation of large volumes of andesities and calc-alkaline granitic rocks, transcurrent faulting, and thrust faulting.

From nappe stacking to extensional detachments at the contact between the Carpathians and Dinarides - The Jastrebac Mountains of Central Serbia

NASA Astrophysics Data System (ADS)

Erak, Dalibor; Matenco, Liviu; Toljić, Marinko; Stojadinović, Uroš; Andriessen, Paul A. M.; Willingshofer, Ernst; Ducea, Mihai N.

2017-07-01

Reactivation of inherited nappe contacts is a common process in orogenic areas affected by back-arc extension. The amount of back-arc extension is often variable along the orogenic strike, owing to the evolution of arcuated mountain chains during stages of rapid slab retreat. This evolution creates low rates of extension near rotation poles, where kinematics and interplay with the pre-existing orogenic structure are less understood. The amount of Miocene extension recorded by the Pannonian Basin of Central Europe decreases SE-wards along the inherited Cretaceous - Paleogene contact between the Dinarides and Carpathian Mountains. Our study combines kinematic data obtained from field and micro-structural observations assisted with fission track thermochronological analysis and U-Pb zircon dating to demonstrate a complex poly-phase evolution in the key area of the Jastrebac Mountains of Serbia. A first event of Late Cretaceous exhumation was followed by latest Cretaceous - Eocene thrusting and magmatism related to a continental collision that sutured the accretionary wedge containing contractional trench turbidites. The suture zone was subsequently reactivated and exhumed by a newly observed Miocene extensional detachment that lasted longer in the Jastrebac Mountains when compared with similar structures situated elsewhere in the same structural position. Such extensional zones situated near the pole of extensional-driven rotation favour late stage truncations and migration of extension in a hanging-wall direction, while directions of tectonic transport show significant differences in short distances across the strike of major structures.

Geology of the Northern Part of the Harcuvar Complex, West-Central Arizona

USGS Publications Warehouse

Bryant, Bruce; Wooden, J.L.

2008-01-01

In west-central Arizona near the northeast margin of the Basin and Range Province, the Rawhide detachment fault separates Tertiary and older rocks lacking significant effects of Tertiary metamorphism from Precambrian, Paleozoic, and Mesozoic rocks in the Harcuvar metamorphic core complex below. Much of the northern part of the Harcuvar complex in the Buckskin and eastern Harcuvar Mountains is layered granitic gneiss, biotite gneiss, amphibolite, and minor pelitic schist that was probably deformed and metamorphosed in Early Proterozoic time. In the eastern Buckskin Mountains, Early and Middle Proterozoic plutons having U-Pb zircon ages of 1,683?6.4 mega-annum (Ma) and 1,388?2.3 Ma, respectively, intruded the layered gneiss. Small plutons of alkaline gabbro and diorite intruded in Late Jurassic time. A sample of mylonitized diorite from this unit has a U-Pb zircon age of 149?2.8 Ma. In the Early Cretaceous, amphibolite facies regional metamorphism was accompanied by partial melting and formation of migmatite. Zircon from a granitic layer in migmatitic gneiss in the eastern Harcuvar Mountains has a U-Pb age of 110?3.7 Ma. In the Late Cretaceous, sills and plutons of the granite of Tank Pass were emplaced in both the Buckskin and eastern Harcuvar Mountains. In the Buckskin Mountains those intrusions are locally numerous enough to form an injection migmatite. A pluton of this granite crops out over almost half the area of the eastern Harcuvar Mountains. Paleozoic and Mesozoic sedimentary rocks were caught as slices along south-vergent Cretaceous thrusts related to the Maria fold and thrust belt and were metamorphosed beneath a thick sheet of Proterozoic crustal rocks. Inception of volcanism and basin formation in upper-plate rocks indicates that regional extension started at about 26 Ma, in late Oligocene. The Swansea Plutonic Suite, composed of rocks ranging from gabbro to granite, intruded the lower-plate rocks in the Miocene and Oligocene(?). Granite and a gabbro from the suite have a U-Pb zircon age of 21.86?0.60 Ma. Previously published 40Ar/39Ar ages of hornblende suggest that some of the Swansea Suite is Oligocene. The felsic rocks contain numerous inclusions ranging from porphyritic granite to porphyritic granodiorite. A sample from one inclusion has a U-Pb zircon age of 1,409?6.3 Ma. A discordia line for the U-Pb zircon data from the Swansea Plutonic Suite has an upper intercept at 1,408?3.4 Ma. The Swansea Plutonic Suite probably formed by interaction between mantle material and plutonic rocks at least as old as Middle Proterozoic. An irregular layer in the middle crust, which is thickest under and adjacent to the Buckskin Mountains, may be the level where that interaction took place. During extensional deformation these rocks and all the older rocks were displaced southwest from beneath the rocks of the Colorado Plateau transition zone below an area extending 50?80 kilometers northeast of the Buckskin Mountains as far as Bagdad, Arizona, or beyond. At that time the rocks were variably mylonitized, and a northeast-trending lineation formed. Much of the evidence for the complex sequence of structural events preserved in these rocks in the western Harcuvar Mountains has been obliterated in the northern Harcuvar complex by Miocene deformation.

Growth and erosion of mountain ranges at the northeastern margin of Tibet

NASA Astrophysics Data System (ADS)

Hetzel, Ralf; Palumbo, Luigi; Giese, Jörg; Guo, Jianming

2010-05-01

The hypothesis that mountain belts may reach a steady state, in which rock uplift is balanced by erosion, has been supported by numerous field studies and numerical models. The early evolution of mountain ranges, however, and especially the relation between fault growth and topographic response has received little attention. By using a space-for-time substitution we illustrate how active thrust faults and small, fault-bounded mountain ranges evolve into mature mountain chains that will ultimately be incorporated into the laterally growing Tibetan Plateau. At an early stage of development, when faults propagate laterally, slip rates are constant along strike [1-3]. As long as no significant topographic relief has developed, tectonic uplift is at least an order of magnitude faster than the rate of erosion [2,4]. During progressive relief growth and the establishment of drainage basins, erosion of the rising mountain ranges becomes more important, but the studied ranges are still in a pre-steady state and continue to grow both vertically and laterally [5]. During this stage the rate of erosion is linearly correlated to the mean hillslope gradient and the mean local relief, if differences in lithology or rock strength are negligible [6]. The rate of relief growth may be inferred from the difference between local erosion rates on ridge crests and catchment-wide denudation rates [7] - the latter may be taken as a surrogate for the rate of river incision. As hillslopes approach a threshold value, landsliding becomes the dominant process of mass transport and erosion rates increase non-linearly with slope. Once a steady state has been reached, the erosion rate is equal to the rate of rock uplift. A key problem is how the rate of rock uplift can be quantified in such regions, because the stochastic distribution of landslides causes the denudation rates inferred from 10Be in river sediment to be highly variable [8]. References [1] Hetzel et al. (2004). Implications of the fault scaling law for the growth of topography: Mountain ranges in the broken foreland of NE Tibet. Terra Nova 16, 157-162. [2] Hetzel et al. (2002). Low slip rates and long-term preservation of geomorphic features in Central Asia. Nature 417, 428-432. [3] Hetzel et al. (2004). Late Pleistocene/Holocene slip rate of the Zhangye thrust (Qilian Shan, China) and implications for the active growth of the northeastern Tibetan Plateau, Tectonics 23, TC6006, doi:10.1029/2004TC001653. [4] Goethals et al. (2009). Determining the impact of faulting on the rate of erosion in a low-relief landscape: A case study using in situ produced 21Ne on active normal faults in the Bishop Tuff, California. Geomorphology 103, 401-413. [5] Palumbo et al. (2009). Deciphering the rate of mountain growth during topographic presteady state: an example from the NE margin of the Tibetan Plateau. Tectonics 28, TC4017, doi:10.1029/2009TC002455. [6] Palumbo et al. (in press). Topographic and lithologic control on catchment-wide denudation rates derived from cosmogenic 10Be in two mountain ranges at the margin of NE Tibet. Geomorphology, doi:10.1016/j.geomorph.2009.11.019. [7] Meyer et al. (in press). Determining the growth rate of topographic relief using in situ-produced 10Be: A case study in the Black Forest, Germany. Earth and Planetary Science Letters. [8] Densmore et al. (2009). Spatial variations in catchment-averaged denudation rates from normal fault footwalls. Geology 37, 1139-1142.

Post-Wildfire Hydrologic Hazards in the Wildland Urban Interface of Colorado and the Western United States

USGS Publications Warehouse

Stevens, M.R.; Bossong, C.R.; Rupert, M.G.; Ranalli, A.J.; Cassidy, E.W.; Druliner, A.D.

2008-01-01

Following a wildfire, such as the 2002 Missionary Ridge fire, a number of hydrologic hazards may develop that can have an important impact on water resources, businesses, homes, reservoirs, roads, and utilities in the wildland urban interface (areas where homes and commercial developments are interspersed with wildlands) in mountainous areas of the Western United States. This fact sheet describes these hazards and identifies approaches to quantify them, thus enabling land and resource managers to plan for and mitigate the effects of these hazards. The fact sheet has been produced in association with the U.S. Geological Survey (USGS) Fire Science Thrust program and the Colorado Front Range Demonstration Project (CFRDP). The current (2007) focus of the CFRDP is on the Three Lakes watershed in Grand County, Colorado, which has applicability to many similar forested, mountain areas in the Western United States.

Formation of fold and thrust belts on Venus due to horizontal shortening of a laterally heterogeneous lithosphere

NASA Technical Reports Server (NTRS)

Zuber, M. T.; Parmentier, E. M.; Neumann, G. A.

1994-01-01

An outstanding question relevant to understanding the tectonics of Venus is the mechanism of formation of fold and thrust belts, such as the mountain belts that surround Lakshmi Planum in western Ishtar Terra. These structures are typically long (hundreds of km) and narrow (many tens of km), and are often located at the margins of relatively high (km-scale) topographic rises. Previous studies have attempted to explain fold and thrust belts in various areas of Venus in the context of viscous and brittle wedge theory. However, while wedge theory can explain the change in elevation from the rise to the adjacent lowland, it fails to account for a fundamental aspect of the deformation, i.e., the topographic high at the edge of the rise. In this study we quantitatively explore the hypothesis that fold and thrust belt morphology on Venus can alternatively be explained by horizontal shortening of a lithosphere that is laterally heterogeneous, due either to a change in thickness of the lithosphere or the crust. Lateral heterogeneities in lithosphere structure may arise in response to thermal thinning or extensive faulting, while variations in crustal thickness may arise due to either spatially variable melting of mantle material or by horizontal shortening of the crust. In a variable thickness lithosphere or crust that is horizontally shortened, deformation will tend to localize in the vicinity of thickness heterogeneity, resulting in a higher component of dynamic topography there as compared to elsewhere in the shortening lithosphere. This mechanism may thus provide a simple explanation for the topographic high at the edge of the rise.

Formation of fold and thrust belts on Venus due to horizontal shortening of a laterally heterogeneous lithosphere

NASA Astrophysics Data System (ADS)

Zuber, M. T.; Parmentier, E. M.; Neumann, G. A.

1994-03-01

An outstanding question relevant to understanding the tectonics of Venus is the mechanism of formation of fold and thrust belts, such as the mountain belts that surround Lakshmi Planum in western Ishtar Terra. These structures are typically long (hundreds of km) and narrow (many tens of km), and are often located at the margins of relatively high (km-scale) topographic rises. Previous studies have attempted to explain fold and thrust belts in various areas of Venus in the context of viscous and brittle wedge theory. However, while wedge theory can explain the change in elevation from the rise to the adjacent lowland, it fails to account for a fundamental aspect of the deformation, i.e., the topographic high at the edge of the rise. In this study we quantitatively explore the hypothesis that fold and thrust belt morphology on Venus can alternatively be explained by horizontal shortening of a lithosphere that is laterally heterogeneous, due either to a change in thickness of the lithosphere or the crust. Lateral heterogeneities in lithosphere structure may arise in response to thermal thinning or extensive faulting, while variations in crustal thickness may arise due to either spatially variable melting of mantle material or by horizontal shortening of the crust. In a variable thickness lithosphere or crust that is horizontally shortened, deformation will tend to localize in the vicinity of thickness heterogeneity, resulting in a higher component of dynamic topography there as compared to elsewhere in the shortening lithosphere. This mechanism may thus provide a simple explanation for the topographic high at the edge of the rise.

Contrasting terrace systems of the lower Moulouya river as indicator of crustal deformation in NE Morocco

NASA Astrophysics Data System (ADS)

Rixhon, Gilles; Bartz, Melanie; El Ouahabi, Meriam; Szemkus, Nina; Brückner, Helmut

2017-02-01

The Moulouya river has the largest catchment in Morocco and drains an area characterized by active crustal deformation during the Late Cenozoic due to the N-S convergence between the African and Eurasian plates. As yet, its Pleistocene terrace sequence remains poorly documented. Our study focuses on the lowermost reach of the river in north-eastern Morocco, which drains the Zebra-Triffa sedimentary basin directly upstream of the estuary. New field observations, measurements and sedimentological data reveal contrasting fluvial environments on each side of a newly identified, W-E striking thrust zone disrupting the sedimentary basin. On the one hand, long-lasting fluvial aggradation, materialized by 37 m-thick stacked terraces, has occurred in the footwall of the thrust. On the other hand, the hanging wall is characterized by a well-preserved terrace staircase, with three Pleistocene terrace levels. Whilst the identification of this thrust zone question some previous interpretations about the local (hydro-)geology, it is consistent with the statement that most of the Plio-Quaternary deformation in the eastern Rif mountains has concentrated in this region of Morocco. Our new data and interpretations also agree with morphometric indicators showing that the whole Moulouya catchment is at desequilibrium state (i.e. several knickzones in its longitudinal profile), showing several knickzones in its longitudinal profile, is at disequilibrium state. We also suggest that the knickzone in the Beni Snassen gorge, located directly upstream of the Zebra-Triffa sedimentary basin, could (partly) result from a transient fluvial reaction to Late Cenozoic thrusting activity and correlated uplift in the hanging wall.

The Mountains of Io: Global and Geological Perspectives from Voyager and Galileo

NASA Technical Reports Server (NTRS)

Schenk, Paul; Hargitai, Henrik; Wilson, Ronda; McEwen, Alfred; Thomas, Peter; Bredekamp, Joe (Technical Monitor)

2001-01-01

To search for local and global scale geologic associations that may be related to the internal dynamics of Io, we have completed a global catalog of all mountains and volcanic centers. We have identified 115 mountain structures (covering approx. 3% of the surface) and 541 volcanic centers, including paterae (calderas and dark spots) and shield volcanoes. The average length of an Ionian mountain is 157 km, with the longest being 570 km. The mean height of Ionian mountains is 6.3 km, and the highest known mountain is Boosaule Montes (17.5 +/- 3 km). Five basic morphologic types of mountains have been identified; mesa, plateau peak, ridge, and massif. Very few mountains bear any physical similarity. to classic volcanic landforms, but many resemble flatiron mountains on Earth and are interpreted as tilted crustal blocks. This would be consistent with the hypothesis that most mountains are thrust blocks formed as a result of compressive stresses built up in the lower crust due to the global subsidence of volcanic layers as they are buried over time. More than one mechanism may be responsible for all Ionian mountains, however. The proximity of some mountains to paterae may indicate a direct link between some mountains and volcanism, although it is not always clear which came first. In contrast to earlier studies, a pronounced bimodal pattern is observed in the global distribution of both mountains and volcanic centers. The regions of highest areal densities of volcanic centers are near the sub- and anti-Jovian regions, but are offset roughly 90deg in longitude from the two, regions of greatest concentration of mountains. This anticorrelation may indicate the overprinting of a second stress field on the global compressive stresses due to subsidence. The bimodal distribution of volcanic centers and mountains is consistent with models of asthenospheric tidal heating and internal convection developed by Tackley et al.Over regions of mantle upwelling, compressive stresses in the lower crust induced by global subsidence might be reduced, encouraging volcanism and discouraging mountain building. In regions of mantle downwelling, these compressive stresses in the lower crust might be increased, discouraging volcanism and encouraging mountain building. Alternatively, the global pattern may be related to possible (but undocumented) nonsynchronous rotation of lo, which would produce two regions each of compression and extension in the crust. Evidence of layering and of mass wasting, including landslides, block sliding, debris aprons and downslope creep, on Ionian mountains suggests that the crust of Io is essentially a layered stack of partially consolidated volcanic lavas and plume deposits, becoming more consolidated with depth. The lower crust especially may also be ductily deformed, punctuated by volcanic intrusions and faulting at paterae, and broken into blocks, some of which have been uplifted to form mountains.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brumbaugh, William D.; Cook, Kenneth L.

During the summers of 1975 and 1976, a gravity survey was conducted in the Cove Fort - Sulphurdale KGRA and north Mineral Mountains area, Millard and Beaver counties, Utah. The survey consisted of 671 gravity stations covering an area of about 1300 km{sup 2}, and included two orthogonal gravity profiles traversing the area. The gravity data are presented as a terrain-corrected Bouguer gravity anomaly map with a contour interval of 1 mgal and as an isometric three-dimensional gravity anomaly surface. Selected anomaly separation techniques were applied to the hand-digitized gravity data (at 1-km intervals on the Universal Transverse Mercator grid)more » in both the frequency and space domains, including Fourier decomposition, second vertical derivative, strike-filter, and polynomial fitting analysis, respectively. Residual gravity gradients of 0.5 to 8.0 mgal/km across north-trending gravity contours observed through the Cove Fort area, the Sulphurdale area, and the areas east of the East Mineral Mountains, along the west flanks of the Tushar Mountains, and on both the east and west flanks of the north Mineral Mountains, were attributed to north-trending Basin and Range high-angle faults. Gravity highs exist over the community of Black Rock area, the north Mineral Mountains, the Paleozoic outcrops in the east Cove Creek-Dog Valley-White Sage Flats areas, the sedimentary thrust zone of the southern Payant Range, and the East Mineral Mountains. The gravity lows over north Milford Valley, southern Black Rock Desert, Cunningham Wash, and northern Beaver Valley are separated from the above gravity highs by steep gravity gradients attributed to a combination of crustal warping and faulting. A gravity low with a closure of 2 mgal corresponds with Sulphur Cove, a circular topographic features containing sulphur deposits.« less

Active fold-thrust belts in the foreland of eastern Tibet, the Longquan and Xiongpu anticlines in Sichuan, China

NASA Astrophysics Data System (ADS)

Lee, Jian-Cheng; Chan, Yu-Chang; Lu, Chia-Yu; Chen, Chih-Tung; Chu, Hao-Tsu; Liu, Yuiping; Li, Jianzhong

2016-04-01

The 2008 M7.9 Wenchuan earthquake ruptured from the Longmenshan fault system, which is the frontal thrust system in eastern Tibet. Further east toward the foreland area in the Sichuan basin, it sits two anticlinal structures, the Longquan and Xiongpu anticlines, which trends sub-parallel to the Longmenshan range with a distance of about 70-100 km to the mountain front. It is widely considered that these two anticlinal features are attributed to propagation of the eastward extrusion of the eastern Tibetan plateau, similar to the stress system the Wenchuan earthquake. In this study, we carried out field investigations on these two active anticlinal structures in order to characterize the bulk deformation of the anticlines. We also conducted fracture analysis and fault-slip data analysis, in an attempt to characterize the fracture developments of the rock and the paleostress states related to the faulting events associated growth of the anticlines. We thus constructed a series of geological cross sections along these two anticlines. Our results show that the Longquan anticline is characterized by pop up structure with a dominant west-vergent thrust (i.e., backthrust) on the western limb. On the other hand to the eastern limb, an east-vergent thrust only well developed in the middle part of the anticline and die out toward the north and the south. For the Xiongpu anticline, it is characterized by a pre-dominant west-vergent backthrust system without developing an east-vergent thrust. A strike-slip fault and a series of N-S-trending pop-up thrusts cut across the Xiongpu anticline indicate a rather complex stress system with two dominant compression directions, NW-SE and E-W, subsequently or alternatively affected the area. Finally, the fracture analysis revealed that 2-3 pre-dominant bedding-perpendicular fracture sets are commonly developed in the massive sandstone layers. Most of them seemingly are of the characteristics of the mode I open joint, without clear relationship with the stress system associated with the regional anticlinal growth.

Tectonically controlled relief evolution in the Northern Tien Shan and Junggar Alatau from the Eocene to the Present

NASA Astrophysics Data System (ADS)

Seib, N.; Kley, J.; Voigt, T.; Kober, M.

2012-04-01

The Cenozoic Tien Shan and Junggar Alatau mountains developed on the southern part of the Paleozoic Altaid orogen as a far-field effect of the collision of the Indian and Eurasian plates. Highland terrain, active seismicity, and fast GPS-derived motions are evidence of rapid ongoing mountain growth today. Variations in relief energy, hight-to-width ratio of ranges and apatite fission track (AFT) exhumation ages suggest they rose at different times. The strong dissection of the higher ridges (heights of up to 2km), indicates an earlier onset and higher rates of uplift. At the other end of the spectrum are low, little dissected ridges. According to AFT ages, exhumation in the Junggar Range began at 9 Ma (Jolivet et al., 2010), circa 11 Ma in the central Kyrgyz Range (Sobel et al., 2006) and 10 Ma in the Terskey Alatau. An AFT age of the low Sogety range is 77 Ma, suggesting that the Cenozic exhumation of the ridge was insufficient to expose rocks from below c.3 km depth. The synclinal lows between the basement highs preserve Cenozoic strata of Eocene to Quaternary age, probably deposited in a once continuous basin (the Ili Basin) and recording the entire history of Tien Shan uplift. Facies pattern of proximal alluvial fans are strictly related to the recent higher mountain areas in the north and in the south. During Middle Miocene, a large lake developed in the basin center. Up to the Middle Miocene sedimentation was accompanied by normal faulting of small magnitude. The main Cenozoic folding and thrusting occurred after that time and before deposition of the Chorgos formation. Shortening was accommodated by reactivation of inherited basement structures, by a switch to reverse or strike-slip motion on normal faults, and the nucleation of new thrusts. The majority of faults which emplace basement rocks over upper Cenozoic sediments dip steeply at angles of 60-70˚, and some have throws of more than 200 m. They are marked by topographic steps and contrasting morphology across them. This first phase of deformation was followed by erosional leveling. Well-consolidated caliche layers indicate an extended period of stable soil formation in a (semi-)arid climate. Renewed shoting and uplift led to river incision and the formation of terraces and gave rise to new active faults, but their displacements are still low due to their short lifespans. These faults are presently expressed at the surface as fold scarps. The scarps are underlain by flexures affected in places by small thrust faults. Some of them, judging by their directions, are probably reactivating Miocene faults. The differences in the timing of range uplift, the progression of Cenozoic folding and the location of the young flexures all indicate migration of thrusting and folding from the borders of the Ili basin toward its center. A similar pattern of tectonic activity shifting from the flanking ridges toward the basin center was also observed in the Issyk-Kul basin (Korzhenkov, et al., 2007).

Restoration of the Cretaceous uplift of the Harz Mountains, North Germany: Evidence for thick-skinned thrusting

NASA Astrophysics Data System (ADS)

Tanner, David C.; Krawczyk, Charlotte M.

2017-04-01

Fault prediction and kinematic restoration are useful tools to firstly determine the likely geometry of a fault at depth and secondly restore the pre-deformation state to discover, for instance, paleogeometry. The inclined-shear method with constant slip uses the known geometry of the surface position and dip of the fault and the geometries of the hanging and footwall beds to predict the probable shape of the fault at depth, down to a detachment level. We use this method to determine the geometry of the Northern Harz Boundary Fault in northern Germany that was responsible for the uplift of the Harz Mountains during Late Cretaceous inversion. A shear angle of 30° was most likely in this case, as indicated by geological and geophysical data. This suggests that the detachment level is at a depth of ca. 25 km. Kinematic restoration of the Harz Mountains using this fault geometry does not produce a flat horizon, rather it results in a 3.5 km depression. Restoration also causes a rotation of fabrics within the Harz Mountains of approximately 11° clockwise. Airy-Heiskanen isostatic equilibrium adjustment reduces the depression to ca. 1 km depth, as well as raising the Moho from 41 to 36 km depth. We show that this model geometry is also a very good fit to the interpreted DEKORP BASIN 9601 deep seismic profile.

Evidence of Vertical and Horizontal Motions on Venus: Maxwell Montes

NASA Astrophysics Data System (ADS)

Ansan, V.; Vergely, P.

1995-01-01

Based on full-resolution Magellan radar images, the detailed structural analysis of central Ishtar Terra (Venus) provides new insight to the understanding of the Venusian tectonics. Ishtar Terra, centered on 65° N latitude and 0° E longitude includes a high plateau. Lakshmi Planum, surrounded by highlands, the most important being Maxwell Montes to the East. Structural analysis has been performed with classical remote-sensing methods. Folds and faults identified on radar images were reported on structural map. Their type and distribution allowed to define the style of the crustal deformation and the context in which these structures formed. This analysis shows that Lakshmi Planum formed under a crustal stretching associated with a volcanic activity. This area then became a relatively steady platform, throughout the formation of Maxwell Montes mountain belt. Maxwell Montes is characterized by a series of NNW-SSE trending thrust faults dipping to the East, formed during a WSW-ESE horizontal shortening. In its NW quarter, the mountain belt shows a disturbed deformation controlled by pre-existing grabens and old vertical crustal fault zone. The deformation of this area is characterized by a shortening of cover above a flat detachment zone, with a progressive accommodation to the southwest. All these tectonic structures show evidence of horizontal and vertical crustal movements on Venus, with subsidence, mountain belt raise, West regional overthrusting of this mountain belt, and regional shear zone.

Geologic Map of the Denver West 30' x 60' Quadrangle, North-Central Colorado

USGS Publications Warehouse

Kellogg, Karl S.; Shroba, Ralph R.; Bryant, Bruce; Premo, Wayne R.

2008-01-01

The Denver West quadrangle extends east-west across the entire axis of the Front Range, one of numerous uplifts in the Rocky Mountain region in which Precambrian rocks are exposed. The history of the basement rocks in the Denver West quadrangle is as old as 1,790 Ma. Along the east side of the range, a sequence of sedimentary rocks as old as Pennsylvanian, but dominated by Cretaceous-age rocks, overlies these ancient basement rocks and was upturned and locally faulted during Laramide (Late Cretaceous to early Tertiary) uplift of the range. The increasingly coarser grained sediments up section in rocks of latest Cretaceous to early Tertiary age record in remarkable detail this Laramide period of mountain building. On the west side of the range, a major Laramide fault (Williams Range thrust) places Precambrian rocks over Cretaceous sedimentary rocks. The geologic history of the quadrangle, therefore, can be divided into four major periods: (1) Proterozoic history, (2) Pennsylvanian to pre-Laramide, Late Cretaceous history, (3) Late Cretaceous to early Tertiary Laramide mountain building, and (4) post-Laramide history. In particular, the Quaternary history of the Denver West quadrangle is described in detail, based largely on extensive new mapping.

Reinterpretation of ADOCH and COCORP Seismic Reflection Data with Constraints from Detailed Forward Modeling of Potential Field Data - Implications for Laurentia-Peri-Gondwana Suture

NASA Astrophysics Data System (ADS)

Duff, P.; Kellogg, J. N.

2017-12-01

To better constrain the structure of the Laurentian - Peri-Gondwana suture zone, maps and a 2-dimensional regional cross-section model constrained by seismic data and surface geology have been developed by forward and inverse modeling the aeromagnetic and gravity fields. The Central Piedmont Suture (CPS), the boundary between the Laurentian Inner Piedmont and the Peri-Gondwanan Carolina terrane is a low-angle thrust fault ( 30°) ramping up from an Alleghanian mid-crustal detachment at depths of about 12 km. ADCOH and COCORP seismic data image anticlinal structures in the footwalls of the Hayesville thrust and the CPS, above the Alleghanian decollement. The footwall rocks have previously been interpreted as Paleozoic shelf strata on the basis of sub-horizontal seismic reflectors; however, the high densities required to fit the observed gravity anomaly suggest that the folded footwall reflectors may need to be reinterpreted as horse blocks or duplex structures of Grenvillian basement. The Appalachian paired gravity anomaly can be explained by an increase in crustal thickness and a decrease in upper crustal density moving northwestward from the Carolina Terrane toward the Appalachian core. A change in lower crustal density is not required, so that Grenville basement rocks may extend farther to the southeast than previously thought. The 5 to 10 km of Alleghanian uplift and exhumation predicted by P-T crystallization data compiled in this paper can be easily accommodated by thrusting on four major low-angle thrust systems: Great Smoky Mountain Thrust (GSMT), Hayesville, Brevard, and CPS. Unroofing of metamorphic core complexes by normal faulting may therefore not be required to explain the observed exhumation. Alleghanian collision along the southeastern Appalachian margin was predominately orthogonal to strike consistent with the previous reconstructions that call for the counter-clockwise rotation of Gondwanan West Africa, creating head-on collision in the southern Appalachians and at least 370 km of shortening.

Mesozoic contractile and extensional structures in the Boyer Gap area, northern Dome Rock Mountains, Arizona

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boettcher, S.S.

1993-04-01

Mesozoic polyphase contractile and superposed ductile extensional structures affect Proterozoic augen gneiss, Paleozoic metasedimentary rocks, and Jurassic granitoids in the Boyer Gap area of the northern Dome Rock Mtns, W-central Arizona. The nappe-style contractile structures are preserved in the footwall of the Tyson Thrust shear zone, which is one of the structurally lowest thrust faults in the E-trending Jurassic and Cretaceous Maria fold and thrust belt. Contractile deformation preceded emplacement of Late Cretaceous granite (ca 80 Ma, U-Pb zircon) and some may be older than variably deformed Late Jurassic leucogranite. Specifically, detailed structural mapping reveals the presence of a km-scalemore » antiformal syncline that apparently formed as a result of superposition of tight to isoclinal, south-facing folds on an earlier, north-facing recumbent fold. The stratigraphic sequence of metamorphosed Paleozoic cratonal strata is largely intact in the northern Dome Rock Mtns, such that overturned and upright stratigraphic units can be distinguished. A third phase of folding in the Boyer Gap area is distinguished by intersection lineations that are folded obliquely across the hinges of open to tight, sheath folds. The axial planes of the sheet folds are subparallel to the mylonitic foliation in top-to-the-northeast extensional shear zones. The timing of ductile extensional structures in the northern Dome Rock is constrained by [sup 40]Ar/[sup 39]Ar isochron ages of 56 Ma and 48 Ma on biotite from mylonitic rocks in both the hanging wall and footwall of the Tyson Thrust shear zone. The two early phases of folding are the dominant mechanism by which shortening was accommodated in the Boyer Gap area, as opposed to deformation along discrete thrust faults with large offset. All of the ductile extensional structures are spectacularly displayed at an outcrop scale but are not of sufficient magnitude to obliterate the km-scale Mesozoic polyphase contractile structures.« less

Potential earthquake faults offshore Southern California, from the eastern Santa Barbara Channel south to Dana Point

USGS Publications Warehouse

Fisher, M.A.; Sorlien, C.C.; Sliter, R.W.

2009-01-01

Urban areas in Southern California are at risk from major earthquakes, not only quakes generated by long-recognized onshore faults but also ones that occur along poorly understood offshore faults. We summarize recent research findings concerning these lesser known faults. Research by the U.S. Geological Survey during the past five years indicates that these faults from the eastern Santa Barbara Channel south to Dana Point pose a potential earthquake threat. Historical seismicity in this area indicates that, in general, offshore faults can unleash earthquakes having at least moderate (M 5-6) magnitude. Estimating the earthquake hazard in Southern California is complicated by strain partitioning and by inheritance of structures from early tectonic episodes. The three main episodes are Mesozoic through early Miocene subduction, early Miocene crustal extension coeval with rotation of the Western Transverse Ranges, and Pliocene and younger transpression related to plate-boundary motion along the San Andreas Fault. Additional complication in the analysis of earthquake hazards derives from the partitioning of tectonic strain into strike-slip and thrust components along separate but kinematically related faults. The eastern Santa Barbara Basin is deformed by large active reverse and thrust faults, and this area appears to be underlain regionally by the north-dipping Channel Islands thrust fault. These faults could produce moderate to strong earthquakes and destructive tsunamis. On the Malibu coast, earthquakes along offshore faults could have left-lateral-oblique focal mechanisms, and the Santa Monica Mountains thrust fault, which underlies the oblique faults, could give rise to large (M ??7) earthquakes. Offshore faults near Santa Monica Bay and the San Pedro shelf are likely to produce both strike-slip and thrust earthquakes along northwest-striking faults. In all areas, transverse structures, such as lateral ramps and tear faults, which crosscut the main faults, could segment earthquake rupture zones. ?? 2009 The Geological Society of America.

Lithospheric Structure of the Zagros and Alborz Mountain Belts (Iran) from Seismic Imaging

NASA Astrophysics Data System (ADS)

Paul, A.; Hatzfeld, D.; Kaviani, A.; Tatar, M.

2008-12-01

We present a synthesis of the results of two dense temporary passive seismic experiments installed for a few months across Central Zagros for the first one, and from North-western Zagros to Alborz for the second one. On both transects, the receiver function analysis shows that the crust has an average thickness of ~ 43 km beneath the Zagros fold-and-thrust belt and the Iranian plateau. The crust is thicker in the back side of the Main Zagros Reverse Fault (MZRF), with a larger maximum Moho depth in Central Zagros (69 ± 2 km) than in North-western Zagros (56 ± 2 km). To reconcile Bouguer anomaly data and Moho depth profile of Central Zagros, we proposed that the thickening is related to overthrusting of the Arabian margin by Central Iran on the MZRF considered as a major thrust fault rooted at Moho depth. The better-quality receiver functions of NW Zagros display clear conversions on a low-velocity channel which cross-cuts the whole crust from the surface trace of the MZRF to the Moho on 250-km length. Waveform modeling shows that the crustal LVZ is ~ 10-km thick with a S-wave velocity 8-30 % smaller than the average crustal velocity. We interpret the low-velocity channel as the trace of the thrust fault and the suture between the Arabian and the Iranian lithospheres. We favour the hypothesis of the LVZ being due to sediments of the Arabian margin dragged to depth during the subduction of the Neotethyan Ocean. At upper mantle depth, we find shield-like shear-wave velocities in the Arabian upper-mantle, and lower velocities in the Iranian shallow mantle (50-150 km) which are likely due to higher temperature. The lack of a high-velocity anomaly in the mantle northeast of the MZRF suture suggests that the Neotethian oceanic lithosphere is now detached from the Arabian margin. The crust of the Alborz mountain range is not thickened in relation with its high elevations, but its upper mantle has low P-wave velocities.

Extent and architecture of major fault systems between northern Victoria Land and the eastern margin of the Wilkes Subglacial Basin (East Antarctica)

NASA Astrophysics Data System (ADS)

Armadillo, E.; Ferraccioli, F.; Balbi, P.; Bozzo, E.

2013-12-01

Terrane bounding and intra-terrane faults of the Ross Orogen in East Antarctica are linked to several phases of Cambrian to Ordovician age subduction and accretion along the active paleo-Pacific margin of Gondwana. Here we compile and analyse new enhanced aeromagnetic anomaly images over the Northern Victoria Land (NVL) segment of the Ross Orogen and the eastern margin of the Wilkes Subglacial Basin (WSB) that help constrain the extent and structural architecture of these fault systems and enable us re-assess their tectonic evolution. Long-wavelength magnetic lows and residual Bouguer gravity highs are modelled as several-km thick inverted sedimentary basins of early Cambrian(?) age. Tectonic inversion occurred along major thrust faults during the late stages of the Ross Orogen, forming a major high-grade pop-up structure within the central Wilson Terrane, flanked by lower grade rocks. The Prince Albert Fault System can now be recongnised as being located to the west of the Exiles Thrust fault system rather than representing its southern continuation. Relatively thin sheets of mylonitic sheared granitoids and possible ultramafic lenses are associated with the late-Ross (ca 480 Ma) Exiles Thrust fault system, while significantly larger and thicker batholiths were emplaced along the Prince Albert Fault System. Recent zircon U-Pb dating over small exposures of gabbro-diorites within the Prince Albert Mountains to the south lead us to propose that this part of the magmatic arc was emplaced during an earlier phase of subduction (~520 Ma or older?), compared to the late-Ross intrusions to the east. Whether the Prince Albert Fault System was indeed a major cryptic suture in early Cambrian times (Ferraccioli et al., 2002, GRL) remains speculative, but possible. Our aeromagnetic interpretation leads us to conclude that these inherited terrane bounding and intra-terrane fault systems of the Ross Orogen exerted a key influence on Cenozoic tectonic blocks and faults of the Transantarctic Mountains, and that the eastern margin of the WSB adjacent to NVL was also strongly controlled by a complex array of major intraplate strike-slip fault systems.

Tectonic evolution of the central Brooks Range mountain front: Evidence from the Atigun Gorge region

USGS Publications Warehouse

Mull, C.G.; Glenn, R.K.; Adams, K.E.

1997-01-01

Atigun Gorge, at the northern front of the eastern Endicott Mountains, contains well-exposed rocks of the upper part of the Endicott Mountains allochthon and rocks of the structurally higher Picnic Creek or Ipnavik River allochthon. These allochthons contain rocks as young as Early Cretaceous (Valanginian) and are separated by a nearly vertical fault zone that contains exotic blocks of Triassic and Jurassic chert and silicified mudstone. Siliceous rocks of this type are not present in the Endicott Mountains allochthon but are characteristic of the Picnic Creek, Ipnavik River, and some of the other allochthons that structurally overlie the Endicott Mountains allochthon in the central and western Brooks Range. These exotic blocks, therefore indicate that structurally higher rocks of either the Picnic Creek or Ipnavik River allochthon were emplaced during the Early Cretaceous and are preserved along the northern flank of the eastern Endicott Mountains. The deformed thickness of this higher allochthon in the subsurface north of the mountains is unknown but probably exceeds 2 kilometers. Similar relations are mapped east of Atigun Gorge in an area of structural transition from the eastern Endicott Mountains into the northern Philip Smith Mountains, which are formed by the parautochthonous North Slope stratigraphic assemblage. The allochthonous rocks at the mountain front are regionally unconformably overlain by proximal Lower Cretaceous (Albian) foredeep conglomerate at the southern flank of the Colville basin, but at Atigun Gorge, the base of these deposits is interpreted as a possible back thrust at a triangle zone. Conglomerate clasts in the foredeep deposits are dominantly chert, mafic igneous rock, and other lithologies characteristic of the Picnic Creek and Ipnavik River allochthons and scattered clasts from the Endicott Mountains allochthon. The conglomerates show that the chert-rich allochthonous rocks and the Endicott Mountains allochthon were emplaced in the north-central Brooks Range by large-scale crustal shortening (>300 km) between the Valanginian and Albian (??135 to ??112 Ma). This orogenic event significantly postdates early stages of Brooks Range orogeny but predates later stages of orogeny documented by stratigraphic and apatite fission-track data. These relations reduce the magnitude of shortening inferred at the triangle zone at the Brooks Range mountain front. The outcrop data suggest that some of the strata preserved at a structurally low level north of the mountain front and visible in the seismic data of the Trans-Alaska Crustal Transect (TACT) may consist of clastic sedimentary rocks of the structurally higher Picnic Creek or Ipnavik River allochthon. Copyright 1997 by the American Geophysical Union.

Integrating GIS-based geologic mapping, LiDAR-based lineament analysis and site specific rock slope data to delineate a zone of existing and potential rock slope instability located along the grandfather mountain window-Linville Falls shear zone contact, Southern Appalachian Mountains, Watauga County, North Carolina

USGS Publications Warehouse

Gillon, K.A.; Wooten, R.M.; Latham, R.L.; Witt, A.W.; Douglas, T.J.; Bauer, J.B.; Fuemmeler, S.J.

2009-01-01

Landslide hazard maps of Watauga County identify >2200 landslides, model debris flow susceptibility, and evaluate a 14km x 0.5km zone of existing and potential rock slope instability (ZEPRSI) near the Town of Boone. The ZEPRSI encompasses west-northwest trending (WNWT) topographic ridges where 14 active/past-active rock/weathered rock slides occur mainly in rocks of the Grandfather Mountain Window (GMW). The north side of this ridgeline is the GMW / Linville Falls Fault (LFF) contact. Sheared rocks of the Linville Falls Shear Zone (LFSZ) occur along the ridge and locally in the valley north of the contact. The valley is underlain principally by layered granitic gneiss comprising the Linville Falls/Beech Mountain/Stone Mountain Thrust Sheet. The integration of ArcGIS??? - format digital geologic and lineament mapping on a 6m LiDAR (Light Detecting and Ranging) digital elevation model (DEM) base, and kinematic analyses of site specific rock slope data (e.g., presence and degree of ductile and brittle deformation fabrics, rock type, rock weathering state) indicate: WNWT lineaments are expressions of a regionally extensive zone of fractures and faults; and ZEPRSI rock slope failures concentrate along excavated, north-facing LFF/LFSZ slopes where brittle fabrics overprint older metamorphic foliations, and other fractures create side and back release surfaces. Copyright 2009 ARMA, American Rock Mechanics Association.

Recognition of surface lithologic and topographic patterns in southwest Colorado with ADP techniques

NASA Technical Reports Server (NTRS)

Melhorn, W. N.; Sinnock, S.

1973-01-01

Analysis of ERTS-1 multispectral data by automatic pattern recognition procedures is applicable toward grappling with current and future resource stresses by providing a means for refining existing geologic maps. The procedures used in the current analysis already yield encouraging results toward the eventual machine recognition of extensive surface lithologic and topographic patterns. Automatic mapping of a series of hogbacks, strike valleys, and alluvial surfaces along the northwest flank of the San Juan Basin in Colorado can be obtained by minimal man-machine interaction. The determination of causes for separable spectral signatures is dependent upon extensive correlation of micro- and macro field based ground truth observations and aircraft underflight data with the satellite data.

Kinematics and Ophiolite obduction in the Gerania and Helicon Mountains, central Greece

NASA Astrophysics Data System (ADS)

Kaplanis, A.; Koukouvelas, I.; Xypolias, P.; Kokkalas, S.

2013-06-01

New structural, petrofabric and palaeostress data from the Beotia area (central Greece) were used to investigate the tectonic evolution of the suture zone between the External (Parnassus microplate) and Internal Hellenides (Pelagonian microplate). Petrofabric studies of ultramafic rocks were done using conventional U-stage analysis and the electron backscatter diffraction (EBSD) technique. Detailed structural analysis enabled us to distinguish three main deformation phases that took place from the Triassic to the Eocene. Triassic-Jurassic deformation is related to continental rifting and the progressive formation of an ocean basin. Ophiolites formed above a westward-dipping supra-subduction zone (SSZ) in the Early-Late Jurassic. Trench-margin collision resulted in the southeastward emplacement of the ophiolite nappe over the Pelagonian margin. There is also evidence for a north-westward thrusting of ophiolitic rocks over the Gerania and Helicon units during Berriasian time. This latter tectonic process is closely related to the deposition of "Beotian flysch" into a foreland basin. An extensional phase of deformation accompanied by shallow-water carbonate sedimentation is documented in the Upper Cretaceous. Later, during Paleocene the area was subjected to a compressional deformation phase characterised by SW-directed thrusting and folding, as well as NE-verging backthrusts and backfolds. Our proposed geotectonic model suggests the consumption of the ocean between the Parnassus and Pelagonian microplates. This model includes Late Jurassic eastward ophiolite obduction followed by Early Cretaceous west directed ophiolite thrusting.

Neogene shortening and exhumation of the Zagros fold-thrust belt and foreland basin in the Kurdistan region of northern Iraq

NASA Astrophysics Data System (ADS)

Koshnaw, Renas I.; Horton, Brian K.; Stockli, Daniel F.; Barber, Douglas E.; Tamar-Agha, Mazin Y.; Kendall, Jerome J.

2017-01-01

The Zagros fold-thrust belt in the Kurdistan region of Iraq encroached southward toward a rapidly subsiding Neogene foreland basin and was later partitioned by out-of-sequence shortening focused along the Mountain Front Flexure (MFF), as defined by new low-temperature thermochronologic, stratigraphic, and provenance results. Apatite (U-Th)/He ages document rapid deformation advance from the Main Zagros Fault to southern frontal structures (Kirkuk, Shakal, and Qamar thrusts) at 10-8 Ma, followed by potential basement-involved out-of-sequence development of the MFF (Qaradagh anticline) by 5 Ma. Distinct shifts in detrital zircon U-Pb provenance signatures for Neogene foreland basin fill provide evidence for drainage reorganization during fold-thrust belt advance. U-Pb age spectra and petrologic data from the Injana (Upper Fars) Formation indicate derivation from a variety of Eurasian, Pan-African, ophiolitic and Mesozoic-Cenozoic volcanic terranes, whereas the Mukdadiya (Lower Bakhtiari) and Bai-Hasan (Upper Bakhtiari) Formations show nearly exclusive derivation from the Paleogene Walash-Naopurdan volcanic complex near the Iraq-Iran border. Such a sharp cutoff in Eurasian, Pan-African, and ophiolitic sources is likely associated with drainage reorganization and tectonic development of the geomorphic barrier formed by the MFF. As a result of Zagros crustal shortening, thickening and loading, the Neogene foreland basin developed and accommodated an abrupt influx of fluvial clastic sediment that contains growth stratal evidence of synkinematic accumulation. The apparent out-of-sequence pattern of upper crustal shortening in the hinterland to foreland zone of Iraqi Kurdistan suggests that structural inheritance and the effects of synorogenic erosion and accumulation are important factors influencing the irregular and episodic nature of orogenic growth in the Zagros.

The Dauki Thrust Fault and the Shillong Anticline: An incipient plate boundary in NE India?

NASA Astrophysics Data System (ADS)

Ferguson, E. K.; Seeber, L.; Steckler, M. S.; Akhter, S. H.; Mondal, D.; Lenhart, A.

2012-12-01

The Shillong Massif is a regional contractional structure developing across the Assam sliver of the Indian plate near the Eastern Syntaxis between the Himalaya and Burma arcs. Faulting associated with the Shillong Massif is a major source of earthquake hazard. The massif is a composite basement-cored asymmetric anticline and is 100km wide, >350km long and 1.8km high. The high relief southern limb preserves a Cretaceous-Paleocene passive margin sequence despite extreme rainfall while the gentler northern limb is devoid of sedimentary cover. This asymmetry suggests southward growth of the structure. The Dauki fault along the south limb builds this relief. From the south-verging structure, we infer a regional deeply-rooted north-dipping blind thrust fault. It strikes E-W and obliquely intersects the NE-SW margin of India, thus displaying three segments: Western, within continental India; Central, along the former passive margin; and Eastern, overridden by the west-verging Burma accretion system. We present findings from recent geologic fieldwork on the western and central segments. The broadly warped erosional surface of the massif defines a single anticline in the central segment, east of the intersection with the hinge zone of the continental margin buried by the Ganges-Brahmaputra Delta. The south limb of the anticline forms a steep topographic front, but is even steeper structurally as defined by the Cretaceous-Eocene cover. Below it, Sylhet Trap Basalts intrude and cover Precambrian basement. Dikes, presumably parallel to the rifted margin, are also parallel to the front, suggesting thrust reactivation of rift-related faults. Less competent Neogene clastics are preserved only near the base of the mountain front. Drag folds in these rocks suggest north-vergence and a roof thrust above a blind thrust wedge floored by the Dauki thrust fault. West of the hinge zone, the contractional structure penetrates the Indian continent and bifurcates. After branching into the Dapsi Fault, the Dauki Fault continues westward as the erosion-deposition boundary combined with a belt of N-S shortening. The Dapsi thrust fault strikes WNW across the Shillong massif and dips NNE. It is mostly blind below a topographically expressed fold involving basement and passive-margin cover. Recent fieldwork has shown that the fault is better exposed in the west, where eventually Archean basement juxtaposes folded and steeply dipping fluvial sediment. Both Dauki and Dapsi faults probably continue beyond the Brahmaputra River, where extreme fluvial processes mask them. The area between the two faults is a gentle southward monocline with little or no shortening. Thus uplift of this area stems from slip on the Dauki thrust fault, not from pervasive shortening. The Burma foldbelt overrides the Shillong Plateau and is warped but continuous across the eastern segment of the Dauki fault. The Haflong-Naga thrust front north of the Dauki merges with the fold-thrust belt in the Sylhet basin to the south, despite >150km of differential advance due to much greater advance of the accretionary prism in the basin. Where the Dauki and Haflong-Naga thrusts cross, the thrust fronts are nearly parallel and opposite vergence. We trace a Dauki-related topographic front eastward across the Burma Range. This and other evidence suggest that the Dauki Fault continues below the foldbelt.

Basin-mountain structures and hydrocarbon exploration potential of west Junggar orogen in China

NASA Astrophysics Data System (ADS)

Wu, X.; Qi, X.; Zheng, M.

2015-12-01

Situated in northern Xinjiang, China, in NE-SW trend, West Junggar Orogen is adjacent to Altai fold belt on the north with the Ertix Fault as the boundary, North Tianshan fold belt on the south with the Ebinur Lake Strike-slip Fault as the boundary, and the Junggar Basin on the southeast with Zaire-Genghis Khan-Hala'alat fold belt as the boundary. Covering an area of about 10×104 km2 in China, there are medium and small intermontane basins, Burqin-Fuhai, Tacheng, Hefeng and Hoxtolgay, distributing inside the orogen. Tectonically West Junggar Orogen lies in the middle section of the Palaeo-Asian tectonic domain where the Siberia, Kazakhstan and Tarim Plates converge, and is the only orogen trending NE-SW in the Palaeo-Asian tectonic domain. Since the Paleozoic, the orogen experienced pre-Permian plate tectonic evolution and post-Permian intra-plate basin evolution. Complex tectonic evolution and multi-stage structural superimposition not only give rise to long term controversial over the basin basement property but also complex basin-mountain coupling relations, structures and basin superimposition modes. According to analysis of several kinds of geological and geophysical data, the orogen was dominated by compressive folding and thrust napping from the Siberia plate in the north since the Late Paleozoic. Compressive stress weakened from north to south, corresponding to subdued vertical movement and enhanced horizontal movement of crustal surface from north to south, and finally faded in the overthrust-nappe belt at the northwest margin of the Junggar Basin. The variation in compressive stress is consistent with the surface relief of the orogen, which is high in the north and low in the south. There are two kinds of basin-mountain coupling relationships, i.e. high angle thrusting and overthrusting and napping, and two kinds of basin superimposition modes, i.e. inherited and progressive, and migrating and convulsionary modes. West Junggar orogen has rich oil and gas shows. Tacheng Basin, north faulted fold belt in the Heshituoluogai basin, and Hongyan fault bench zone in north Ulungur Depression in the Junggar Basin are promising areas for hydrocarbon exploration.

Normal Faulting in the 1923 Berdún Earthquake and Postorogenic Extension in the Pyrenees

NASA Astrophysics Data System (ADS)

Stich, Daniel; Martín, Rosa; Batlló, Josep; Macià, Ramón; Mancilla, Flor de Lis; Morales, Jose

2018-04-01

The 10 July 1923 earthquake near Berdún (Spain) is the largest instrumentally recorded event in the Pyrenees. We recover old analog seismograms and use 20 hand-digitized waveforms for regional moment tensor inversion. We estimate moment magnitude Mw 5.4, centroid depth of 8 km, and a pure normal faulting source with strike parallel to the mountain chain (N292°E), dip of 66° and rake of -88°. The new mechanism fits into the general predominance of normal faulting in the Pyrenees and extension inferred from Global Positioning System data. The unique location of the 1923 earthquake, near the south Pyrenean thrust front, shows that the extensional regime is not confined to the axial zone where high topography and the crustal root are located. Together with seismicity near the northern mountain front, this indicates that gravitational potential energy in the western Pyrenees is not extracted locally but induces a wide distribution of postorogenic deformation.

Tertiary tilting and dismemberment of the laramide arc and related hydrothermal systems, Sierrita Mountain, Arizona

USGS Publications Warehouse

Stavast, W.J.A.; Butler, R.P.; Seedorff, E.; Barton, M.D.; Ferguson, C.A.

2008-01-01

Multiple lines of evidence, including new and published geologic mapping and paleomagnetic and geobarometric determinations, demonstrate that the rocks and large porphyry copper systems of the Sierrita Mountains in southern Arizona were dismembered and tilted 50?? to 60?? to the south by Tertiary normal faulting. Repetition of geologic features and geobarometry indicate that the area is segmented into at least three major structural blocks, and the present surface corresponds to oblique sections through the Laramide plutonic-hydrothermal complex, ranging in paleodepth from ???1 to ???12 km. These results add to an evolving view of a north-south extensional domain at high angles to much extension in the southern Basin and Range, contrast with earlier interpretations that the Laramide systems are largely upright and dismembered by thrust faults, highlight the necessity of restoring Tertiary rotations before interpreting Laramide structural and hydrothermal features, and add to the broader understanding of pluton emplacement and evolution of porphyry copper systems. ?? 2008 Society of Economic Geologists, Inc.

Fracture density and grain size controls on the relief structure of threshold landscapes

NASA Astrophysics Data System (ADS)

DiBiase, R.; Rossi, M. W.; Neely, A.

2015-12-01

A central goal in geomorphology is to untangle the competing controls of climate, tectonics, and rock strength on the topography and relief structure of mountain ranges. This is important for deciphering the history of climate and tectonics encoded in landscapes, predicting natural hazards, and quantifying critical zone processes. Incorporating rock strength into landscape evolution models has been a particularly challenging problem, because the factors that determine rock strength vary in importance depending on process. Here we propose a mechanism of hillslope-channel coupling by which tectonically-induced fracturing influences the relief structure of steep, rocky "threshold" landscapes by leading to A) increased fracture density in exposed bedrock outcrops, thereby limiting hillslope relief, and B) decreased grain size of channel bed material, thereby reducing the magnitude of fluvial incision thresholds and increasing the erosional efficiency of bedrock rivers. To test this hypothesis, we compare two contrasting landscapes in southern California—the eastern San Gabriel Mountains and the northern San Jacinto Mountains. The eastern San Gabriel Mountains rise 2 km in relief and exhibit high uplift and erosion rates due to active faulting along the Cucamonga thrust fault. Although bedrock on hillslopes is common, the exposed granitic and metamorphic basement rock is highly fractured at the decimeter or finer scale, and river channels are mantled with a thin layer of gravel-cobble alluvium. The northern San Jacinto Mountains, 80 km to the southeast, experience similar mean runoff and daily runoff variability, and are underlain by similar bedrock. Yet, despite an absence of active faulting, and erosion rates slower than the eastern San Gabriel Mountains by a factor of 5, the northern San Jacinto Mountains preserve one of the steepest escarpments in the contiguous US (2-3 km high), characterized by massive bedrock outcrops on hillslopes with meter-scale or larger fracture spacing, and a resulting channel network mantled with large boulders. Preliminary analyses suggest that fracture spacing and bed material grain size in threshold landscapes are tightly coupled, and influence the steepness of hillslopes and channels that control the relief structure of mountain ranges in a predictable manner.

Stratigraphy and structural setting of Upper Cretaceous Frontier Formation, western Centennial Mountains, southwestern Montana and southeastern Idaho

USGS Publications Warehouse

Dyman, T.S.; Tysdal, R.G.; Perry, W.J.; Nichols, D.J.; Obradovich, J.D.

2008-01-01

Stratigraphic, sedimentologic, and palynologic data were used to correlate the Frontier Formation of the western Centennial Mountains with time-equivalent rocks in the Lima Peaks area and other nearby areas in southwestern Montana. The stratigraphic interval studied is in the middle and upper parts (but not uppermost) of the formation based on a comparison of sandstone petrography, palynologic age data, and our interpretation of the structure using a seismic line along the frontal zone of the Centennial Mountains and the adjacent Centennial Valley. The Frontier Formation is comprised of sandstone, siltstone, mudstone, limestone, and silty shale in fluvial and coastal depositional settings. A distinctive characteristic of these strata in the western Centennial Mountains is the absence of conglomerate and conglomeratic sandstone beds. Absence of conglomerate beds may be due to lateral facies changes associated with fluvial systems, a distal fining of grain size, and the absence of both uppermost and lower Frontier rocks in the study area. Palynostratigraphic data indicate a Coniacian age for the Frontier Formation in the western Centennial Mountains. These data are supported by a geochronologic age from the middle part of the Frontier at Lima Peaks indicating a possible late Coniacian-early Santonian age (86.25 ?? 0.38 Ma) for the middle Frontier there. The Frontier Formation in the western Centennial Mountains is comparable in age and thickness to part of the Frontier at Lima Peaks. These rocks represent one of the thickest known sequences of Frontier strata in the Rocky Mountain region. Deposition was from about 95 to 86 Ma (middle Cenomanian to at least early Santonian), during which time, shoreface sandstone of the Telegraph Creek Formation and marine shale of the Cody Shale were deposited to the east in the area now occupied by the Madison Range in southwestern Montana. Frontier strata in the western Centennial Mountains are structurally isolated from other Cretaceous rocks in the region and are part of the Lima thrust sheet that lies at the leading edge of the Sevier-style overthrusting in this part of southwestern Montana and adjacent southeastern Idaho.

Offshore Tectonics of the St. Elias Mountains: Insights from Ocean Drilling and Seismic Stratigraphy on the Yakutat Shelf

NASA Astrophysics Data System (ADS)

Worthington, L. L.; Gulick, S. P. S.; Montelli, A.; Jaeger, J. M.; Zellers, S.; Walczak, M. H.; Mix, A. C.

2015-12-01

Ongoing collision of the Yakutat (YAK) microplate with North America (NA) in southern Alaska has driven orogenesis of the St. Elias Mountains and the advance of the offshore deformation front to the southeast. The offshore St. Elias fold-thrust belt records the complex interaction between collisional tectonics and glacial climate variability, providing insight for models of orogenesis and the evolution of glacial depocenters. Glacial erosion and deposition have provided sediment that constructed the upper continental shelf, much of which has been reincorporated into the orogenic wedge through offshore faulting and folding. We integrate core and downhole logging data from IODP Expedition 341 (Sites U1420 and U1421) drilled on the Yakutat shelf and slope with high-resolution and regional seismic profiles to investigate the coupled structural and stratigraphic evolution of the St. Elias margin. Site U1420 lies on the Yakutat shelf within the Bering Trough, a shelf-crossing trough that is within primary depocenter for Bering Glacier sediments. Two faults underlie the glacial packages and have been rendered inactive as the depositional environment has evolved, while faulting elsewhere on the shelf has initiated. Site U1421 lies on the current continental slope, within the backlimb of an active thrust that forms part of the modern YAK-NA deformation front. At each of these sites, we recovered glacigenic diamict (at depths up to ~1015 m at Site U1420), much of which is younger than 0.3 Ma. Age models within the trough indicated that initiation of active deformation away from the Bering Trough depocenter likely occurred since 0.3 Ma, suggesting that possible tectonic reorganization due to mass redistribution by glacial processes can occur at time scales on the order of 100kyr-1Myr.

Morphologic expression of Quaternary deformation in the northwestern foothills of the Ysyk-Köl basin, Tien Shan

NASA Astrophysics Data System (ADS)

Korjenkov, A. M.; Povolotskaya, I. E.; Mamyrov, E.

2007-03-01

The Tien Shan is one of the most active intracontinental mountain belts exhibiting numerous examples of Quaternary fault-related folding. To provide insight into the deformation of the Quaternary intermontane basins, the territory of the northwestern Ysyk-Köl region, where the growing Ak-Teke Anticline divided the piedmont apron of alluvial fans, is studied. It is shown that the Ak-Teke Hills are a sharply asymmetric anticline, which formed as a result of tectonic uplift and erosion related to motions along the South Ak-Teke Thrust Fault. The tectonic uplift gave rise to the local deviation of the drainage network in front of the northern limb of the fold. Optical (luminescent) dating suggests that the tectonic uplifting of the young anticline and the antecedent downcutting started 157 ka ago. The last upthrow of the high floodplain of the Toru-Aygyr River took place 1300 years ago. The structure of the South Ak-Teke Fault is examined by means of seismologic trenching and shallow seismic profiling across the fault. A laser tachymeter is applied to determine the vertical deformation of alluvial terraces in the Toru-Aygyr River valley at its intersection with the South Ak-Teke Fault. The rates of vertical deformation and an inferred number of strong earthquakes, which resulted in the upthrow of Quaternary river terraces of different ages, are calculated. The study territory is an example of changes in fluvial systems on growing folds in piedmont regions. As a result of shortening of the Earth’s crust in the mountainous belt owing to thrusting, new territories of previous sedimentation are involved in emergence. The tectonic activity migrates with time from the framing ridges toward the axial parts of intramontane basins.

Thermal consequences of thrust faulting: simultaneous versus successive fault activation and exhumation

NASA Astrophysics Data System (ADS)

ter Voorde, M.; de Bruijne, C. H.; Cloetingh, S. A. P. L.; Andriessen, P. A. M.

2004-07-01

When converting temperature-time curves obtained from geochronology into the denudation history of an area, variations in the isotherm geometry should not be neglected. The geothermal gradient changes with depth due to heat production and evolves with time due to heat advection, if the deformation rate is high. Furthermore, lateral variations arise due to topographic effects. Ignoring these aspects can result in significant errors when estimating denudation rates. We present a numerical model for the thermal response to thrust faulting, which takes these features into account. This kinematic two-dimensional model is fully time-dependent, and includes the effects of alternating fault activation in the upper crust. Furthermore, any denudation history can be imposed, implying that erosion and rock uplift can be studied independently to each other. The model is used to investigate the difference in thermal response between scenarios with simultaneous compressional faulting and erosion, and scenarios with a time lag between rock uplift and denudation. Hereby, we aim to contribute to the analysis of the mutual interaction between mountain growth and surface processes. We show that rock uplift occurring before the onset of erosion might cause 10% to more than 50% of the total amount of cooling. We applied the model to study the Cenozoic development of the Sierra de Guadarrama in the Spanish Central System, aiming to find the source of a cooling event in the Pliocene in this region. As shown by our modeling, this temperature drop cannot be caused by erosion of a previously uplifted mountain chain: the only scenarios giving results compatible with the observations are those incorporating active compressional deformation during the Pliocene, which is consistent with the ongoing NW-SE oriented convergence between Africa and Iberia.

Tectonics of the North American Cordillera near the Fortieth Parallel

USGS Publications Warehouse

King, P.B.

1978-01-01

The North American Cordillera near the Fortieth Parallel consists of the following tectonic units: 1. (A) To the east is a reactivated cratonic area, in the Southern Rocky Mountains and Colorado Plateau, in which the supracrustal rocks (Cambrian to Cretaceous) were broadly deformed during the late Cretaceous-Paleocene Laramide orogeny, and the Precambrian basement was raised in folds of wide amplitude. 2. (B) West of it is a miogeosynclinal belt, in the eastern Great Basin, in which a thick sequence of Paleozoic carbonates and related deposits was thrust eastward along low-angle faults during the middle to late Cretaceous Sevier orogeny. The miogeosyncline is the downwarped western margin of the original North American continent, and its rocks accumulated on Precambrian basement. 3. (C) Beyond is a eugeosynclinal belt, in the western Great Basin, in which Paleozoic graywackes, cherts, and volcanics were thrust easteastward along low-angle faults during several Paleozoic orogenies - the mid-Paleozoic Antler orogeny which produced the Roberts thrust on the east, and the end-Paleozoic Sonoma orogeny which produced the Golconda thrust farther west. The Paleozoic eugeosynclinal rocks accumulated on oceanic basement. They are overlapped from the west by Triassic and Jurassic shelf deposits, which pass westward into eugeosynclinal deposits. 4. (D) A volcanic island-arc belt existed on the sites of the Sierra Nevada in Paleozoic and early Mesozoic time, which produced thick bodies of sediments and volcanics. During the mid-Mesozoic Nevadan orogeny these were steeply deformed and thrust westward over subduction zones, and were intruded by granitic rocks that rose from the upper mantle to form great batholiths. 5. (E) West of the Sierra Nevada, in the Great Valley, is a great sedimentary embankment of later Mesozoic flysch or turbidite, largely younger than the supracrustal rocks of the Sierra Nevada and the Nevadan orogeny. It was formed of the erosional products of the supracrustal and granitic rocks of the Sierra Nevada. 6. (F) This sequence is, in turn, thrust westward over the Mesozoic Franciscan terrane of the Coast Ranges, which forms the westernmost belt of the Cordillera, and which is being treated in other papers in this symposium. The net effect of the prolonged events that produced the Cordillera in this segment has been the addition of successive tectonic belts to the North American continent at the expense of the Pacific Ocean basin during Phanerozoic time. ?? 1978.

Integrating seismic reflection and geological data and interpretations across an internal basement massif: The southern Appalachian Pine Mountain window, USA

USGS Publications Warehouse

McBride, J.H.; Hatcher, R.D.; Stephenson, W.J.; Hooper, R.J.

2005-01-01

The southern Appalachian Pine Mountain window exposes 1.1 Ga Grenvillian basement and its metasedimentary Paleozoic(?) cover through the allochthonous Inner Piedmont. The issue of whether the crustal block inside the window was either transported above the master Appalachian (late Alleghanian) de??collement or is an autochthonous block that was overridden by the de??collement has been debated for some time. New detrital zircon geochronologic data from the cover rocks inside the window suggest this crustal block was derived from Gondwana but docked with Laurentia before the Alleghanian event. Reprocessed deep seismic reflection data from west-central Georgia (pre- and poststack noise reduction, amplitude variation analysis, and prestack depth migration) indicate that a significant band of subhorizontal reflections occurs almost continuously beneath the window collinear with the originally recognized de??collement reflections north of the window. A marked variation in the de??collement image, from strong and coherent north of the window to more diffuse directly beneath the window, is likely a partial consequence of the different geology between the Inner Piedmont and the window. The more diffuse image beneath the window may also result from imaging problems related to changes in topography and fold of cover (i.e., signal-to-noise ratio). Two alternative tectonic models for the Pine Mountain window can partially account for the observed variation in the de??collement reflectivity. (1) The Pine Mountain block could be truncated below by a relatively smooth continuation of the de??collement. The window would thus expose an allochthonous basement duplex or horse-block thrust upward from the south along the Late Proterozoic rifted continental margin. (2) The window represents localized exhumation of autochthonous basement and cover along a zone of distributed intrabasement shearing directly beneath the window. Either model is viable if only reflector geometry is considered; model (1) is favored if both geometry and kinematics of Blue Ridge-Piedmont thrust sheet emplacement are incorporated. In either model, the southern margin of the window merges to the west with the Iapetan early Alleghanian Central Piedmont suture, which juxtaposes North American-affinity Piedmont rocks to the north and exotic Panafrican rocks of the Carolina (Avalon) terrane to the south. Immediately south of the window, this suture dips southward and merges in the lower crust with the late Alleghanian suture joining the Appalachians with Gondwana. ?? 2005 Geological Society of America.

Tectonic evolution and hydrocarbon accumulation in the Yabulai Basin, western China

NASA Astrophysics Data System (ADS)

Zheng, Min; Wu, Xiaozhi

2014-05-01

The Yabulai petroliferous basin is located at the north of Hexi Corridor, western China, striking NEE and covering an area of 1.5×104 km2. It is bounded on the south by Beidashan Mountain to the Chaoshui Basin, on the east by Bayanwulashan Mountain to the Bayanhaote Basin, and on the northwest by Yabulai Mountain to the Yingen-Ejinaqi Basin. It is a Meso-cenozoic compressive depression residual basin. In view of regional geotectonics, the Yabulai basin sits in the middle-southern transition belt of Arershan massif in North China Craton. Driven by Indosinian movement at the late Triassic, two near EW normal faults were developed under the regional extensional stress along the northern fringe of Beidashan Mountain and the southern fringe of Yabulai Mountain front in the Arershan massif, forming the embryonic form of the Yabulai rift lake basin. Since Yanshan period, the Yabulai basin evolved in two major stages: Jurassic rift lake basin and Cretaceous rift lake basin. During early Yanshan period, EW striking Yabulai tensional rift was formed. Its major controlling fault was Beidashan normal fault, and the depocenter was at the south of this basin. During middle Yanshan period, collision orogenesis led to sharp uplift at the north of this basin where the middle-lower Jurassic formations were intensely eroded. During late Yanshan period, the Alashan massif and its northern area covered in an extensional tectonic environment, and EW striking normal faults were generated at the Yabulai Mountain front. Such faults moved violently and subsided quickly to form a new EW striking extensional rift basin with the depocenter at the south of Yabulai Mountain. During Himalayan period, the Alashan massif remained at a SN horizontal compressional tectonic environment; under the compressional and strike slip actions, a NW striking and south dipping thrusting nappe structure was formed in the south of the Yabulai basin, which broke the Beidashan normal fault to provide the echelon fault system and finally present the current structural framework of "east uplift and west depression, south faulted and north overlapping". The Yabulai basin presented as a strike-slip pull-apart basin in Mesozoic and a compressional thrusting depression basin in Cenozoic. Particularly, the Mesozoic tectonic units were distributed at a big included angle with the long axis of the basin, while the Cenozoic tectonic units were developed in a basically consistent direction with the long axis. The sags are segmented. Major subsiding sags are located in the south, where Mesozoic Jurassic-Cretaceous systems are developed, with the thickest sedimentary rocks up to 5300m. Jurassic is the best developed system in this basin. Middle Jurassic provides the principal hydrocarbon-bearing assemblage in this basin, with Xinhe Fm. and Qingtujing Fm. dark mudstone and coal as the source rocks, Xinhe Fm. and Qingtujing Fm. sandstones as the reservoir formation, and Xinhe Fm. mudstones as the cap rocks. However, the early burial and late uplifting damaged the structural framework of the basin, thus leading to the early violent compaction and tightness of Jurassic sandstone reservoir and late hydrocarbon maturity. So, tectonic development period was unmatched to hydrocarbon expulsion period of source rocks. The hydrocarbons generated were mainly accumulated near the source rocks and entrapped in reservoir. Tight oil should be the major exploration target, which has been proved by recent practices.

A remote sensing study of active folding and faulting in southern Kerman province, S.E. Iran

NASA Astrophysics Data System (ADS)

Walker, Richard Thomas

2006-04-01

Geomorphological observations reveal a major oblique fold-and-thrust belt in Kerman province, S.E. Iran. The active faults appear to link the Sabzevaran right-lateral strike-slip fault in southeast Iran to other strike-slip faults within the interior of the country and may provide the means of distributing right-lateral shear between the Zagros and Makran mountains over a wider region of central Iran. The Rafsanjan fault is manifest at the Earth's surface as right-lateral strike-slip fault scarps and folding in alluvial sediments. Height changes across the anticlines, and widespread incision of rivers, are likely to result from hanging-wall uplift above thrust faults at depth. Scarps in recent alluvium along the northern margins of the folds suggest that the thrusts reach the surface and are active at the present-day. The observations from Rafsanjan are used to identify similar late Quaternary faulting elsewhere in Kerman province near the towns of Mahan and Rayen. No instrumentally recorded destructive earthquakes have occurred in the study region and only one historical earthquake (Lalehzar, 1923) is recorded. In addition GPS studies show that present-day rates of deformation are low. However, fault structures in southern Kerman province do appear to be active in the late Quaternary and may be capable of producing destructive earthquakes in the future. This study shows how widely available remote sensing data can be used to provide information on the distribution of active faulting across large areas of deformation.

Retrodeformable cross sections and Oak Ridge fault, Ventura basin, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yeats, R.S.; Huftile, G.F.

1988-03-01

A retrodeformable (balanced) cross section is constructed such that stratified rocks are restored to their undeformed state without loss or gain of bed length or bed thickness. Ductile strata may be area-balanced if original thickness is known. Near Ventura, folds in Pliocene-Pleistocene turbidites and Miocene-early Pliocene shales (Rincon, Monterey, Sisquoc) overlie an unfolded competent Paleogene sequence. The basal decollement of the foldbelt is in the ductile Rincon Formation (lower Miocene). The overlying Sulphur Mountain, Ventura Avenue, San Miguelito, and Rincon anticlines are fault-propagation folds developing from south-dipping, largely late Quaternary frontal ramp thrusts (Sisar-Big Canyon-Lion fault set, Barnard fault set,more » padre Juan fault, and C-3 fault, respectively) that rise from the decollement. Cross-section balancing shows that the overlying fold-thrust belt has shortened 2.5-6 km more than subjacent Paleogene competent strata. This excess bed length is taken up in the Paleogene sequence on the Oak Ridge fault as a ramp from the brittle-plastic transition zone through the upper crust. This implies that the basal decollement is the frontal active thrust of the Oak Ridge fault. The decollement dies out southeast of a line between Timber Canyon oil field and the west end of Oak Ridge, possibly because of decreased ductility in the Miocene decollement sequence due to appearance of sandstone interbeds. Farther southeast, late Quaternary displacement concentrated on the Oak Ridge fault itself at rates greater than 10 mm/year.« less

Regional Landscape Response to Wedge-Top Basin Formation

NASA Astrophysics Data System (ADS)

Ruetenik, G.; Moucha, R.; Hoke, G. D.; Val, P.

2017-12-01

Wedge-top basins are the result of regionally variable uplift along thrust faults downstream of a mountain range and provide an ideal environment to study the regional stream and surface response to local variations in rock uplift. In this study, we simulate the formation and evolution of a wedge-top basin using a landscape evolution model. In line with a previous study, we find that during deformation in the fold-and-thrust belt adjacent to a wedge-top basin, both channel slope and erosion rates are reduced, and these changes propagate as a wave of low erosion into the uplands. For a uniform background uplift rate, this reduced rate of erosion results in a net surface uplift and a decreased slope within and upstream of the wedge-top basin. Following the eventual breach of the basin's bounding thrust belt, a wave of high erosion propagates through the basin and increases the channel slope. We expand upon previous studies by testing our model against a wide range of model parameters, although in general we find that the onset of increased erosion can be delayed by up to several million years. The amount of surface uplift is highly dependent on flexural isostasy and therefore it is heavily influenced by the elastic thickness and erodbility parameters. Observed paleoerosion rates in a paired wedge-top foreland sequence in the Argentine Precordillera reveal similar histories of paleo-erosion, and present day stream profiles show evidence that support model outcomes.

10Be surface exposure dating reveals strong active deformation in the central Andean backarc interior

NASA Astrophysics Data System (ADS)

García Morabito, Ezequiel; Terrizzano, Carla; Zech, Roland; Willett, Sean; Yamin, Marcela; Haghipour, Negar; Wuethrich, Lorenz; Christl, Marcus; María Cortes, José; Ramos, Victor

2016-04-01

Understanding the deformation associated with active thrust wedges is essential to evaluate seismic hazard. How is active faulting distributed throughout the wedge, and how much deformation is taken up by individual structures? We address these questions for our study region, the central Andean backarc of Argentina. We combined a structural and geomorphological approach with surface exposure dating (10Be) of alluvial fans and strath terraces in two key localities at ~32° S: the Cerro Salinas, located in the active orogenic front of the Precordillera, and the Barreal block in the interior of the Andean mountain range. We analysed 22 surface samples and 6 depth profiles. At the thrust front, the oldest terrace (T1) yields an age of 100-130 ka, the intermediate terrace (T2) between 40-95 ka, and the youngest terrace (T3) an age of ~20 ka. In the Andean interior, T1´ dates to 117-146 ka, T2´ to ~70 ka, and T3´ to ~20 ka, all calculations assuming negligible erosion and using the scaling scheme for spallation based on Lal 1991, Stone 2000. Vertical slip rates of fault offsets are 0.3-0.5 mm/yr and of 0.6-1.2 mm/yr at the thrust front and in the Andean interior, respectively. Our results highlight: i) fault activity related to the growth of the Andean orogenic wedge is not only limited to a narrow thrust front zone. Internal structures have been active during the last 150 ka, ii) deformation rates in the Andean interior are comparable or even higher that those estimated and reported along the emerging thrust front, iii) distribution of active faulting seems to account for unsteady state conditions, and iv) seismic hazards may be more relevant in the internal parts of the Andean orogen than assumed so far. References Lal, D., 1991: Cosmic ray labeling of erosion surfaces: In situ nuclide production rates and erosion models. Earth and Planetary Science Letters 104: 424-439. Stone, J.O., 2000: Air pressure and cosmogenic isotope production. Journal of Geophysical Research 105 (B10): 23753-23759

Crustal thickness variations in the Zagros continental collision zone (Iran) from joint inversion of receiver functions and surface wave dispersion

NASA Astrophysics Data System (ADS)

Tatar, M.; Nasrabadi, A.

2013-10-01

Variations in crustal thickness in the Zagros determined by joint inversion of P wave receiver functions (RFs) and Rayleigh wave group and phase velocity dispersion. The time domain iterative deconvolution procedure was employed to compute RFs from teleseismic recordings at seven broadband stations of INSN network. Rayleigh wave phase velocity dispersion curves were estimated employing two-station method. Fundamental mode Rayleigh wave group velocities for each station is taken from a regional scale surface wave tomographic imaging. The main variations in crustal thickness that we observe are between stations located in the Zagros fold and thrust belt with those located in the Sanandaj-Sirjan zone (SSZ) and Urumieh-Dokhtar magmatic assemblage (UDMA). Our results indicate that the average crustal thickness beneath the Zagros Mountain Range varies from ˜46 km in Western and Central Zagros beneath SHGR and GHIR up to ˜50 km beneath BNDS located in easternmost of the Zagros. Toward NE, we observe an increase in Moho depth where it reaches ˜58 km beneath SNGE located in the SSZ. Average crustal thickness also varies beneath the UDMA from ˜50 km in western parts below ASAO to ˜58 in central parts below NASN. The observed variation along the SSZ and UDMA may be associated to ongoing slab steepening or break off in the NW Zagros, comparing under thrusting of the Arabian plate beneath Central Zagros. The results show that in Central Iran, the crustal thickness decrease again to ˜47 km below KRBR. There is not a significant crustal thickness difference along the Zagros fold and thrust belt. We found the same crystalline crust of ˜34 km thick beneath the different parts of the Zagros fold and thrust belt. The similarity of crustal structure suggests that the crust of the Zagros fold and thrust belt was uniform before subsidence and deposition of the sediments. Our results confirm that the shortening of the western and eastern parts of the Zagros basement is small and has only started recently.

Landforms along transverse faults parallel to axial zone of folded mountain front, north-eastern Kumaun Sub-Himalaya, India

NASA Astrophysics Data System (ADS)

Luirei, Khayingshing; Bhakuni, S. S.; Negi, Sanjay S.

2017-02-01

The shape of the frontal part of the Himalaya around the north-eastern corner of the Kumaun Sub-Himalaya, along the Kali River valley, is defined by folded hanging wall rocks of the Himalayan Frontal Thrust (HFT). Two parallel faults (Kalaunia and Tanakpur faults) trace along the axial zone of the folded HFT. Between these faults, the hinge zone of this transverse fold is relatively straight and along these faults, the beds abruptly change their attitudes and their widths are tectonically attenuated across two hinge lines of fold. The area is constituted of various surfaces of coalescing fans and terraces. Fans comprise predominantly of sandstone clasts laid down by the steep-gradient streams originating from the Siwalik range. The alluvial fans are characterised by compound and superimposed fans with high relief, which are generated by the tectonic activities associated with the thrusting along the HFT. The truncated fan along the HFT has formed a 100 m high-escarpment running E-W for ˜5 km. Quaternary terrace deposits suggest two phases of tectonic uplift in the basal part of the hanging wall block of the HFT dipping towards the north. The first phase is represented by tilting of the terrace sediments by ˜30 ∘ towards the NW; while the second phase is evident from deformed structures in the terrace deposit comprising mainly of reverse faults, fault propagation folds, convolute laminations, flower structures and back thrust faults. The second phase produced ˜1.0 m offset of stratification of the terrace along a thrust fault. Tectonic escarpments are recognised across the splay thrust near south of the HFT trace. The south facing hill slopes exhibit numerous landslides along active channels incising the hanging wall rocks of the HFT. The study area shows weak seismicity. The major Moradabad Fault crosses near the study area. This transverse fault may have suppressed the seismicity in the Tanakpur area, and the movement along the Moradabad and Kasganj-Tanakpur faults cause the neotectonic activities as observed. The role of transverse fault tectonics in the formation of the curvature cannot be ruled out.

Geometry and kinematics of Majiatan Fold-and-thrust Belt, Western Ordos Basin: implication for Tectonic Evolution of North-South Tectonic Belt

NASA Astrophysics Data System (ADS)

He, D.

2017-12-01

The Helan-Chuandian North-South Tectonic Belt crossed the central Chinese mainland. It is a boundary of geological, geophysical, and geographic system of Chinese continent tectonics from shallow to deep, and a key zone for tectonic and geomorphologic inversion during Mesozoic to Cenozoic. It is superimposed by the southeastward and northeastward propagation of Qinghai-Tibet Plateau in late Cenozoic. It is thus the critical division for West and East China since Mesozoic. The Majiatan fold-and-thrust belt (MFTB), locating at the central part of HCNSTB and the western margin of Ordos Basin, is formed by the tectonic evolution of the Helan-Liupanshan Mountains. Based on the newly-acquired high-resolution seismic profiles, deep boreholes, and surface geology, the paper discusses the geometry, kinematics, and geodynamic evolution of MFTB. With the Upper Carboniferous coal measures and the pre-Sinian ductile zone as the detachments, MFTB is a multi-level detached thrust system. The thrusting was mainly during latest Jurassic to Late Cretaceous, breaking-forward in the foreland, and resulting in a shortening rate of 25-29%. By structural restoration, this area underwent extension in Middle Proterozoic to Paleozoic, which can be divided into three phases of rifting such as Middle to Late Proterozoic, Cambiran to Ordovician, and Caboniferous to early Permian. It underwent compression since Late Triassic, including such periods as Latest Triassic, Late Jurassic to early Cretaceous, Late Cretaceous to early Paleogene, and Pliocene to Quaternary, with the largest shortening around Late Jurassic to early Cretaceous period (i.e. the mid-Yanshanian movement by the local name). However, trans-extension since Eocene around the Ordos Basin got rise to the formation the Yingchuan, Hetao, and Weihe grabens. It is concluded that MFTB is the leading edge of the intra-continental Helan orogenic belt, and formed by multi-phase breaking-forward thrusting during Late Jurassic to Cretaceous. During Cenozoic, MFTB is moderately modified by the northeastward compression due to the NE propagation of Qinghai-Tibet Plateau, and distinctly superimposed by the Yingchuan half-graben. North-South Tectonic Belt underwent a full cycle from extension during Middle Proterozoic to Paleozoic to compression since late Triassic.

The Inskip Formation, the Harmony Formation, and the Havallah Sequence of Northwestern Nevada - An Interrelated Paleozoic Assemblage in the Home of the Sonoma Orogeny

USGS Publications Warehouse

Ketner, Keith B.

2008-01-01

An area between the towns of Winnemucca and Battle Mountain in northwestern Nevada, termed the arkosic triangle, includes the type areas of the middle to upper Paleozoic Inskip Formation and Havallah sequence, the Upper Devonian to Mississippian Harmony Formation, the Sonoma orogeny, and the Golconda thrust. According to an extensive body of scientific literature, the Havallah sequence, a diverse assemblage of oceanic rocks, was obducted onto the continent during the latest Permian or earliest Triassic Sonoma orogeny by way of the Golconda thrust. This has been the most commonly accepted theory for half a century, often cited but rarely challenged. The tectonic roles of the Inskip and Harmony Formations have remained uncertain, and they have never been fully integrated into the accepted theory. New, and newly interpreted, data are incompatible with the accepted theory and force comprehensive stratigraphic and tectonic concepts that include the Inskip and Harmony Formations as follows: middle to upper Paleozoic strata, including the Inskip, Harmony, and Havallah, form an interrelated assemblage that was deposited in a single basin on an autochthonous sequence of Cambrian, Ordovician, and lowest Silurian strata of the outer miogeocline. Sediments composing the Upper Devonian to Permian sequence entered the basin from both sides, arkosic sands, gravel, limestone olistoliths, and other detrital components entered from the west, and quartz, quartzite, chert, and other clasts from the east. Tectonic activity was expressed as: (1) Devonian uplift and erosion of part of the outer miogeocline; (2) Late Devonian depression of the same area, forming a trough, probably fault-bounded, in which the Inskip, Harmony, and Havallah were deposited; (3) production of intraformational and extrabasinal conglomerates derived from the basinal rocks; and (4) folding or tilting of the east side of the depositional basin in the Pennsylvanian. These middle to upper Paleozoic deposits were compressed in the Jurassic, causing east-verging thrusts in the eastern part of the depositional basin (Golconda thrust) and west-verging thrusts and folds in the western part. Hypotheses involving a far-traveled allochthon that was obducted from an ocean or back-arc basin are incompatible with modern observations and concepts.

Geologic Map of the Clark Peak Quadrangle, Jackson and Larimer Counties, Colorado

USGS Publications Warehouse

Kellogg, Karl S.; Ruleman, Chester A.; Shroba, Ralph R.; Braddock, William A.

2008-01-01

The Clark Peak quadrangle encompasses the southern end of the Medicine Bow Mountains and the northernmost end of the Mummy Range. The Continental Divide traverses the map area and Highway 14 cross the Divide at Cameron Pass, in the southeastern corner of the map. Approximately the eastern half of the map, and a few areas to the west, are underlain by Early Proterozoic plutonic and metamorphic rocks. Most of these basement rocks are part of the ~1,715 Ma Rawah batholith, composed mostly of pinkish, massive to moderately foliated monzogranite and granodiorite intruded by numerous, large pegmatite- aplite bodies. The metamorphic rocks, many of which form large inclusions in the granitic rocks of the Rawah batholith, include biotite-hornblende gneiss, hornblende gneiss, amphibolite, and biotite schist. The crystalline basement rocks are thrust westward along the Medicine Bow thrust over a sequence of sedimentary rocks as old as the Upper Permian Satanka Shale. The Satanka Shale, Middle and Lower Triassic Chugwater group, and a thin sandstone tentatively correlated with the Lower Jurassic and Upper Triassic Jelm Formation are combined as one map unit. This undivided unit is overlain sequentially upward by the Upper Jurassic Sundance Formation, Upper Jurassic Morrison Formation, Lower Cretaceous Dakota Group, Upper and Lower Cretaceous Benton Group, Upper Cretaceous Niobrara Formation, and the Eocene and Paleocene Coalmont Formation. The Late Cretaceous to early Eocene Medicine Bow thrust is folded in places, and several back thrusts produced a complicated thrust pattern in the south part of the map. Early Oligocene magmatism produced rhyolite tuff, dacite and basalt flows, and intermediate dikes and small stocks. A 40Ar/39Ar date on sanidine from one rhyolite tuff is ~28.5 Ma; a similar whole-rock date on a trachybasalt is ~29.6 Ma. A very coarse, unsorted probably pre-Quaternary ridge-top diamicton crops out in the southern part of the quadrangle. Numerous glacial deposits (mostly of Pinedale age), rock glaciers, block-slope deposits, landslide deposits, talus deposits, fan deposits, colluvium, and alluvium comprise the surficial deposits of the map area.

Intraplate extensional tectonics of the eastern Basin-Range Inferencess on structural style from seismic reflection data, regional tectonics, and thermal-mechanical models of brittle-ductile deformation

NASA Technical Reports Server (NTRS)

Smith, R. B.; Bruhn, R. L.

1984-01-01

Using 1500 km of industry-released seismic reflection data, surface geology, velocity models from refraction data, and earthquake data, the large extensional structures in the crust of the eastern Basin-Range and its transition into the Middle Rocky Mountains and Colorado Plateau have been studied. It is suggested that the close spatial correlation between normal faults and thrust fault segmentation along the Wasatch Front reflects major east-trending structural and lithological boundaries inherited from tectonic processes associated with the evolution of the cordilleran miogeocline, which began in the Precambrian.

1. U.S. Route 250 grade separation structure. This reinforced concrete, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. U.S. Route 250 grade separation structure. This reinforced concrete, rigid frame structure was built in 1941. Its relatively flat arch provided maximum useful clearance in a short span and the physics of the design eliminated the need for extensive abutments to contain the thrust of traditional arches, making it ideally suited as a grade separation structure. BLRI designers made extensive use of theses bridges for crossing small streams and creeks, and grade separation structures, ornamenting them with a rustic stone facade. View is of the south-southeast elevation. - Blue Ridge Parkway, Between Shenandoah National Park & Great Smoky Mountains, Asheville, Buncombe County, NC

Saturn Apollo Program

NASA Image and Video Library

1963-01-01

Smokeless flame juts from the diffuser of a unique vacuum chamber in which the upper stage rocket engine, the hydrogen fueled J-2, was tested at a simulated space altitude in excess of 60,000 feet. The smoke you see is actually steam. In operation, vacuum is established by injecting steam into the chamber and is maintained by the thrust of the engine firing through the diffuser. The engine was tested in this environment for start, stop, coast, restart, and full-duration operations. The chamber was located at Rocketdyne's Propulsion Field Laboratory, in the Santa Susana Mountains, near Canoga Park, California. The J-2 engine was developed by Rocketdyne for the Marshall Space Flight Center.

Apatite Fission Track Constraints On The Denudational History Of The Bielsa And Millares Plutons, West-Central Pyrenees, Spain

NASA Astrophysics Data System (ADS)

Schwabe, E.; Fitzgerald, P. G.; Munoz, J. A.; Baldwin, S. L.

2006-12-01

The Pyreneean orogen extends for ~ 440 km from the Bay of Biscay to the Mediterranean Sea, forming a WNW-ESE topographic barrier between France and Spain. The mountain belt, formed by the Late Cretaceous-Early Miocene oblique collision and partial subduction of the Iberian Plate beneath the European Plate. Restored and balanced cross sections show a decrease in crustal shortening from ~165 km in the central Pyrenees to ~ 50 km in the Cantabrian margin, further to the west. The variation in shortening and crustal style is due to the decrease westward in convergence and differences in inherited geometry of pre- existing extensional faults. We propose the variation must also be reflected in the denudation record, with relative timing of the main denudational events younging to the west, as well as the magnitude and rates of denudation decreasing westward. In this study we analyze AFT data collected from vertical profiles on the southern flank of the mountains in the west-central Pyrenees. The results constrain the relative timing of structures between the central and west-central Pyrenees. AFTT data from the Bielsa and Millares massifs, located in the Bielsa and Millares thrust sheets on the southern flank of the axial zone, west-central Pyrenees yield AFT ages from 30 to 20 Ma. The data, including constraints from inverse thermal modeling, indicate denudation at rates ca. 300 m/my underway in the middle Oligocene, slowing in the Miocene. Denudation is likely related to erosion following thrusting during which the granites were transported within the south-vergent Bielsa and Millares thrust sheets. The Late Oligocene-Early Miocene AFT PAZ has since been exhumed to its present elevation. In form, results are similar to those from the central Pyrenees (Fitzgerald et al., 1999) but that Oligocene denudation in the west-central Pyrenees occurred later, was slower, and of reduced magnitude when compared to extremely rapid Oligocene denudation recorded ~50 km east in the central Pyrenees. There, as demonstrated in results from the Maladeta profile, denudation in the Early Oligocene is extremely rapid (km/my) followed by a slowing or cessation of exhumation. The Miocene PAZ preserved in both profiles suggests a similar post- orogenic history most likely related to filling and subsequent re-excavation of the Ebro Basin.

Office of Science and Technology&International Year EndReport - 2005

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bodvarsson, G.S.

2005-10-27

Source Term, Materials Performance, Radionuclide Getters, Natural Barriers, and Advanced Technologies, a brief introduction in each section describes the overall organization and goals of each program area. All of these areas have great potential for improving our understanding of the safety performance of the proposed Yucca Mountain repository, as processes within these areas are generally very conservatively represented in the Total System Performance Assessment. In addition, some of the technology thrust areas in particular may enhance system efficiency and reduce risk to workers. Thus, rather modest effort in the S&T Program could lead to large savings in the lifetime repositorymore » total cost and significantly enhanced understanding of the behavior of the proposed Yucca Mountain repository, without safety being compromised, and in some instances being enhanced. An overall strength of the S&T Program is the significant amount of integration that has already been achieved after two years of research. As an example (illustrated in Figure 1), our understanding of the behavior of the total waste isolation system has been enhanced through integration of the Source Term, Materials Performance, and Natural Barriers Thrust areas. All three thrust areas contribute to the integration of different processes in the in-drift environment. These processes include seepage into the drift, dust accumulation on the waste package, brine formation and precipitation on the waste package, mass transfer through the fuel cladding, changes in the seepage-water chemical composition, and transport of released radionuclides through the invert and natural barriers. During FY2005, each of our program areas assembled a team of external experts to conduct an independent review of their respective projects, research directions, and emphasis. In addition, the S&T Program as a whole was independently reviewed by the S&T Programmatic Evaluation Panel. As a result of these reviews, adjustments to the S&T Program will be implemented in FY2006 to ensure that the Program is properly aligned with OCRWM's priorities. Also during FY2005, several programmatic documents were published, including the Science and Technology Program Strategic Plan, the Science and Technology Program Management Plan, and the Science and Technology Program Plan. These and other communication products are available on the OCRWM web site under the Science and Technology section (http://www.ocrwm.doe.gov/osti/index.shtml).« less

Constraining the Uplift History of the Jabal Akhdar and Saih Hatat Culminations, Al Hajar Mountains, Oman, with Fission Track and (U-Th)/He Ages

NASA Astrophysics Data System (ADS)

Hansman, R. J.; Ring, U.; Thomson, S. N.; Den Brok, B.; Stübner, K.

2016-12-01

We constrain the timing of the enigmatic uplift history of the Al Hajar Mountains in Oman by apatite (U-Th)/He and fission-track (AHe and AFT), as well as zircon (U-Th)/He (ZHe) ages. Our data show differential cooling between the two major culminations of the mountain range, which are separated by the Semail gap, a major NNE-oriented depression in the Al Hajar Mountains. In the up to 3 km high Jabal Akhdar Culmination west of the Semail Gap AHe sample mean ages range between 35.5 ± 4.3 Ma and 23.9 ± 8.8 Ma (1σ errors), AFT ages range 51 ± 4 to 32 ± 2 Ma (1σ errors), and ZHe sample mean ages range 50.6 ± 16.7 to 46.1 ± 7.1 Ma (1σ errors). Whereas, in the Saih Hatat Culmination to the east AHe ages range from 23.6 ± 1.7 Ma to 15.7 ± 4.1 Ma, AFT ages range 73 ± 10 to 57 ± 4 Ma, and ZHe ages range 70.6 ± 10.8 Ma through to 58.8 ± 1.8 Ma. These data demonstrate that the uplift initiated at 45 Ma and had ceased by 15 Ma, climaxing between 40 to 35 Ma. In addition, U-Pb dating of calcite tectonics also supports N-S shortening at 40 to 35 Ma. We propose that the Semail gap is a west-dipping thrust, which uplifted the Jabal Akhdar Culmination in the hanging-wall but hardly affected the Saih Hatat Culmination in the footwall. During mountain uplift, the Al Hajar Mountains were located at least 600 km outboard of the current Eurasia-Arabia subduction/collision zone on the continental margin of the downgoing Arabian Plate. We therefore conclude that the uplift of the Al Hajar Mountains preceded the Zagros collisional event by at least 15 Myr and were not causally related to the Zagros collision and Makran subduction.

The Pinjaur dun (intermontane longitudinal valley) and associated active mountain fronts, NW Himalaya: Tectonic geomorphology and morphotectonic evolution

NASA Astrophysics Data System (ADS)

Singh, Vimal; Tandon, S. K.

2008-12-01

The Himalayan orogenic belt, formed as a result of collision tectonic processes, shows abundant evidence of neotectonic activity, active tectonics, and the occurrence of historical earthquakes. Its frontal deformation zone is characterized, in some segments, by intermontane longitudinal valleys (duns). Such frontal segments of the Himalaya are marked by the occurrence of multiple mountain fronts. In one such segment of the foothills of the NW Himalaya, the Pinjaur dun is developed and marked by three mountain fronts: MF1A and MF1B associated with the southernmost Himalayan Frontal Thrust (HFT), MF2 associated with the Sirsa fault, and MF3 associated with the Barsar thrust along the southern margin of the relatively higher main part of the sub-Himalaya. Geomorphic responses to the tectonic activity of these and related structural features have been analyzed through the use of geomorphic indices, drainage density, stream longitudinal profiles, drainage anomalies, and hypsometric analysis. Also, fault and fold growth and their expression on landform development was studied using a combination of surface profiles and field observations. The values of valley floor width to height ratio ( Vf) for valleys associated with MF1 ranged between 0.07 and 0.74, and for valleys associated with MF2 ranged from 1.02-5.12. Vf for the four major valleys associated with MF1B ranged from 1.1-1.7. The asymmetry factor for 26 drainage basins related to MF1A indicate these have developed under the influence of a transverse structure. These results taken together with those obtained from the Hack profiles and SL index values, hypsometry, drainage density, and drainage anomalies suggest that the faults associated with the mountain fronts and related structures are active. Active tectonics and neotectonic activity have led to the formation of four surfaces in the Pinjaur dun. In addition, an important drainage divide separating the Sirsa and Jhajara drainage networks also developed in the intermontane valley. Surface profile analysis helped in deciphering the growth history of the fault bend fold structures of the outermost Siwalik hills. The effects of tectonic activity on the proximal part of the Indo-Gangetic plains are interpreted from the remarkable river deflections that are aligned linearly over tens of kilometers in a zone about 10 km south of the HFT. Based on these integrated structural and tectonic geomorphological approaches, a morphotectonic evolutionary model of the dun has been proposed. This model highlights the role of uplift and growth history of the fault bend fold structures of the outermost Siwalik hills on (i) the depositional landforms and drainage development of the Pinjaur dun, and (ii) valley development of the outermost Siwalik hills. Importantly, this study postulates the formation of an incipient mountain front that is evolving ahead of the HFT and the outermost Siwalik hills in the Indo-Gangetic plains.

Gravity constraints on the geometry of the Big Bend of the San Andreas Fault in the southern Carrizo Plains and Pine Mountain egion

NASA Astrophysics Data System (ADS)

Altintas, Ali Can

The goal of this project is to combine gravity measurements with geologic observations to better understand the "Big Bend" of the San Andreas Fault (SAF) and its role in producing hydrocarbon-bearing structures in the southern Central Valley of California. The SAF is the main plate boundary structure between the Pacific and North American plates and accommodates ?35 mm/yr of dextral motion. The SAF can be divided into three main parts: the northern, central and southern segments. The boundary between the central and southern segments is the "Big Bend", which is characterized by an ≈30°, eastward bend. This fault curvature led to the creation of a series of roughly east-west thrust faults and the transverse mountain ranges. Four high-resolution gravity transects were conducted across locations on either side of the bend. A total of 166 new gravity measurements were collected. Previous studies suggest significantly inclined dip angle for the San Andreas Fault in the Big Bend area. Yet, our models indicate that the San Andreas Fault is near vertical in the Big Bend area. Also gravity cross-section models suggest that flower structures occur on either side of the bend. These structures are dominated by sedimentary rocks in the north and igneous rocks in the south. The two northern transects in the Carrizo plains have an ≈-70 mgal Bouguer anomaly. The SAF has a strike of ≈315° near these transects. The northern transects are characterized by multiple fault strands which cut marine and terrestrial Miocene sedimentary rocks as well as Quaternary alluvial valley deposits. These fault strands are characterized by ?6 mgal short wavelength variations in the Bouguer gravity anomaly, which correspond to low density fault gouge and fault splays that juxtapose rocks of varying densities. The southern transects cross part of the SAF with a strike of 285°, have a Bouguer anomaly of ≈-50 mgal and are characterized by a broad 15 mgal high. At this location the rocks on either side of the fault are Proterozoic - Cretaceous metamorphic or/and plutonic rocks. Previous work based on geologic mapping hypothesized the existence of a shallow, low angle Abel Mountain Thrust in which crystalline rocks were thrust over Miocene sedimentary rocks, near Apache Saddle. However, gravity models indicate the crystalline rocks are vertically extensive and form a positive flower structure bounded by high angle faults. Also, based on the thickness of fault adjacent sedimentary cover, the gravity models suggest a minimum exhumation of 5-6 km for crystalline rocks in the south. Assuming exhumation began with the switch from the transtensional San Gabriel Fault to transpressional San Andreas Fault at approximately 5 Ma, this indicates exhumation rates of 1 km/Ma. Overall, the broad gravity highs observed along the southern transects are due to uplift of basement rocks in this area.

Preliminary geologic map of the Murrieta 7.5' quadrangle, Riverside County, California

USGS Publications Warehouse

Kennedy, Michael P.; Morton, Douglas M.

2003-01-01

The Murrieta quadrangle is located in the northern part of the Peninsular Ranges Province and includes parts of two structural blocks, or structural subdivisions of the province. The quadrangle is diagonally crossed by the active Elsinore fault zone, a major fault zone of the San Andreas fault system, and separates the Santa Ana Mountains block to the west from the Perris block to the east. Both blocks are relatively stable internally and within the quadrangle are characterized by the presence of widespread erosional surfaces of low relief. The Santa Ana Mountains block, in the Murrieta quadrangle, is underlain by undifferentiated, thick-layered, granular, impure quartzite and well-layered, fissile, phyllitic metamorphic rock of low metamorphic grade. Both quartzite and phyllitic rocks are Mesozoic. Unconformably overlying the metamorphic rocks are remnants of basalt flows having relatively unmodified flow surfaces. The age of the basalt is about 7-8Ma. Large shallow depressions on the surface of the larger basalt remnants form vernal ponds that contain an endemic flora. Beneath the basalt the upper part of the metamorphic rocks is deeply weathered. The weathering appears to be the same as the regional Paleocene saprolitic weathering in southern California. West of the quadrangle a variable thickness sedimentary rock, physically resembling Paleogene rocks, occurs between the basalt and metamorphic rock. Where not protected by the basalt, the weathered rock has been removed by erosion. The dominant feature on the Perris block in the Murrieta quadrangle is the south half of the Paloma Valley ring complex, part of the composite Peninsular Ranges batholith. The complex is elliptical in plan view and consists of an older ring-dike with two subsidiary short-arced dikes that were emplaced into gabbro by magmatic stoping. Small to large stoped blocks of gabbro are common within the ring-dikes. A younger ring-set of hundreds of thin pegmatite dikes occur largely within the central part of the complex. These pegmatite dikes were emplaced into a domal fracture system, apparently produced by cauldron subsidence, and include in the center of the complex, a number of flat-floored granophyre bodies. The granophyre is interpreted to be the result of pressure quenching of pegmatite magma. Along the eastern edge of the quadrangle is the western part of a large septum of medium metamorphic grade Mesozoic schist. A dissected basalt flow caps the Hogbacks northeast of Temecula, and represents remnants of a channel filling flow. Beneath the basalt is a thin deposit of stream gravel. Having an age of about 10Ma, this basalt is about 2-3Ma older than the basalt flows in the Santa Ana Mountains. The Elsinore fault zone forms a complex of pull-apart basins. The west edge of the fault zone, the Willard Fault, is marked by the high, steep eastern face of the Santa Ana Mountains. The east side of the zone, the Wildomar Fault, forms a less pronounced physiographic step. In the center of the quadrangle a major splay of the fault zone, the Murrieta Hot Springs Fault, strikes east. Branching of the fault zone causes the development of a broad alluvial valley between the Willard Fault and the Murrieta Hot Springs Fault. All but the axial part of the zone between the Willard and Wildomar Faults consist of dissected Pleistocene sedimentary units. The axial part of the zone is underlain by Holocene and latest Pleistocene sedimentary units.

Late extension in compressional wedges above a weak, viscous décollement: results from analogue modeling

NASA Astrophysics Data System (ADS)

Borderie, Sandra; Vendeville, Bruno C.; Graveleau, Fabien; Witt, César

2016-04-01

Extension during convergence is a structural process commonly encountered in different geodynamic settings, such as accretionary wedges subjected to tectonic erosion, or mountain belts undergoing post-orogenic collapse. This has been investigated with experimental models at the scale of doubly-vergent wedges (Haq and Davis 2008; Bonini et al. 2000, Buck and Sokoutis 1994) but not thoroughly at the scale of fold-and-thrust belts. During an experimental investigation carried out on the behavior of segmented fold-and-thrust belts induced by stratigraphic inheritance in the foreland series (Borderie et al., EGU this session), unexpected shallow normal faulting occurred. The models comprised one basal frictional décollement (glass microbeads) and one upper viscous décollement embedded in the cover (silicone polymer). Extension took place during the late stages of the experiments and it was localized at the transition zone between the rear domain of the wedge and the frontal fold-and-thrust belt that detached on the upper viscous décollement. Normal faults strike parallel to the compressional structures and mainly dip toward the foreland. They root in the viscous décollement. Through a series of parametrized experiments dedicated to constrain the timing of formation of these extensional structures, we could evidence that these normal faults appear once the bulk shortening in the rear domain has created enough uplift of the internal zone by antiformal stacking and enough forelandward tilting of the upper viscous décollement. These two latter mechanisms are direct consequences of the whole wedge dynamics that links the thrust fault dynamics in the upper shallow sedimentary sequence and the thrust dynamics of the deep subsalt basement. The occurrence of this extension depends on the initial position of the upper viscous décollement and notably the position of the internal pinchout relative to the position of the backstop. Additional tests have also demonstrated that this extension is prevented by surface processes and notably sedimentation. We compare our experimental findings with natural examples of extensional features in various fold-and-thrust belts and accretionary features across the world (e.g. the Mediterranean ridge). References: Bonini, Marco, Dimitrios Sokoutis, Genene Mulugeta, and Emmanouil Katrivanos. 2000. "Modelling Hanging Wall Accommodation above Rigid Thrust Ramps." Journal of Structural Geology 22 (8): 1165-79. Borderie, Sandra, Fabien Graveleau, Cesar Witt and Bruno C. Vendeville. 2016. "Analogue modeling of 3-D structural segmentation in fold-and-thrust belts: interactions between frictional and viscous provinces in foreland basins." Gephys. Res. Abstr., 18, EGU2016-Vienne. Buck, W Roger, and Dimitrios Sokoutis. 1994. "Analogue Model of Gravitational Collapse and Surface Extension during Continental Convergence." Nature 369: 737-40. Haq, Saad SB, and Dan M. Davis. 2008. "Extension during Active Collision in Thin-Skinned Wedges: Insights from Laboratory Experiments." Geology 36 (6): 475-78.

A viscoelastic strain energy principle expressed in fold thrust belts and other compressional regimes

NASA Astrophysics Data System (ADS)

Patton, Regan L.; Watkinson, A. John

2005-07-01

A mathematical folding theory for stratified viscoelastic media in layer parallel compression is presented. The second order fluid, in slow flow, is used to model rock rheological behavior because it is the simplest nonlinear constitutive equation exhibiting viscoelastic effects. Scaling and non-dimensionalization of the model system reveals the presence of Weissenberg number ( Wi), defined as a ratio of time scales τ*/( H*/ V*). V*/ H* is the strain rate (s -1) imposed by an assumed far field velocity V* acting on a layer of thickness H*, while τ* (s) is related to the relaxation of normal stresses. Our most significant finding is a transitional behavior as Wi→½, which is independent of the viscosity contrast. A change of variables shows that lengths associated with this transition are scaled by a parameter α=[(1-2 Wi)/(1+2 Wi)] 1/2, which is inversely proportional to local strain energy. On this basis a scaling law representing a distribution of non-dimensional wavelengths (wavelength/layer thickness) is derived. Geologically this is consistent with a transition from folding to faulting, as observed in fold-thrust belts. Folding, a distributed deformation scaling as Wi-1, is found to be energetically favored at non-dimensional wavelengths ranging from about three to seven. Furthermore, the transition from folding to faulting, a localized deformation scaling as ( αWi) -1, is predicted at a non-dimensional wavelength of about seven. These findings are consistent with measurements of thrust sheets in the Sawtooth Mountains of western Montana, USA and other fold-thrust belts. A review of the literature reveals a similar distribution of non-dimensional wavelengths spanning a wide range of observational scales in compressional deformation. Specific examples include lithospheric scale folding in the central Indian Basin and microscopic scale failure of ice columns between splay microcracks in laboratory studies.

Drainage reorganization during mountain building in the river system of the Eastern Cordillera of the Colombian Andes

NASA Astrophysics Data System (ADS)

Struth, Lucía; Babault, Julien; Teixell, Antonio

2015-12-01

The Eastern Cordillera of Colombia is a thick-skinned thrust-fold belt that is characterized by two topographic domains: (1) the axial zone, a high altitude plateau (the Sabana de Bogotá, 2500 masl) with low local relief and dominated by longitudinal rivers, and (2) the Cordillera flanks, where local relief exceeds 1000 m and transverse rivers dominate. On the basis of an analysis of digital topography and river parameters combined with a review of paleodrainage data, we show that the accumulation of shortening and crustal thickening during the Andean orogeny triggered a process of fluvial reorganization in the Cordillera. Owing to a progressive increase of the regional slope, the drainage network evolves from longitudinal to transverse-dominated, a process that is still active at present. This study provides the idea of progressive divide migration toward the inner part of the mountain belt, by which the area of the Sabana de Bogotá plateau is decreasing, the flanks increase in area, and ultimately transverse rivers will probably dominate the drainage of the Cordillera.

Glaciers in the Himalayan Mountains taken from Atlantis during STS-106

NASA Image and Video Library

2000-09-16

STS106-705-009 (8-20 September 2000) --- One of the STS-106 crew members on board the Space Shuttle Atlantis used a handheld 70mm camera to photograph this image of Qogir Feng (8,611 meters), which appears at the far upper left in this view of the northwestern Karakoram Range. Also called K2 or Mt. Godwin Austen, the mountain is the second highest peak in the world. The Tarim sedimentary basin borders the range on the north and the Lesser Himalayas on the south. Melt waters from vast glaciers, such as those south and east of K2, feed agriculture in the valleys (dark green) and contribute significantly to the regional fresh-water supply. The Karakoram Range lies along the southern edge of the Eurasian tectonic plate and is made up of ancient sedimentary rocks (more than 390 million years old, according to geologists studying the shuttle imagery). Those strata were folded and thrust-faulted, and granite masses were intruded, say the geologists, when the Indo-Pakistan plate collided with Eurasia, beginning more than 100 million years ago.

Geologic map of the Seldovia quadrangle, south-central Alaska

USGS Publications Warehouse

Bradley, Dwight C.; Kusky, Timothy M.; Haeussler, Peter J.; Karl, Susan M.; Donley, D. Thomas

1999-01-01

This is a 1:250,000-scale map of the bedrock geology of the Seldovia quadrangle, south-central Alaska. The map area covers the southwestern end of the Kenai Peninsula, including the Kenai Lowlands and Kenai Mountains, on either side of Kachemak Bay. The waters of Cook Inlet cover roughly half of the map area, and a part of the Alaska Peninsula near Iliamna Volcano lies in the extreme northwest corner of the map. The bedrock geology is based on new reconnaissance field work by the U.S. Geological Survey during parts of the 1988-1993 field seasons, and on previous mapping from a number of sources. The new mapping focused on the previously little-known Chugach accretionary complex in the Kenai Mountains. Important new findings include the recognition of mappable subdivisions of the McHugh Complex (a subduction melange of mostly Mesozoic protoliths), more accurate placement of the thrust contact between the McHugh Complex and Valdez Group (Upper Cretaceous trench turbidites), and the recognition of several new near-trench plutons of early Tertiary age.

Sediment underthrusting within a continental magmatic arc: Coast Mountains batholith, British Columbia

NASA Astrophysics Data System (ADS)

Pearson, David M.; MacLeod, Douglas R.; Ducea, Mihai N.; Gehrels, George E.; Jonathan Patchett, P.

2017-10-01

Though continental magmatic arcs are factories for new continental crust, a significant proportion of continental arc magmas are recycled from supracrustal material. To evaluate the relative contributions of retroarc underthrusting and trench side partial sediment subduction for introducing supracrustal rocks to the middle and lower crust of continental magmatic arcs, we present results from the deeply exposed country rocks of the Coast Mountains batholith of western British Columbia. Prior work demonstrates that these rocks underwent widespread partial melting that contributed to the Coast Mountains batholith. We utilize U-Pb zircon geochronology, Sm-Nd thermochronology, and field-based studies to document the protoliths and early burial history of amphibolite and granulite-facies metasedimentary rocks in the Central Gneiss Complex. U-Pb detrital zircon data from the structurally highest sample localities yielded 190 Ma unimodal age peaks and suggest that retroarc rocks of the Stikine terrane constitute a substantial portion of the Central Gneiss Complex. These supracrustal rocks underwent thrust-related burial and metamorphism at >25 km depths prior to 80 Ma. These rocks may also be underlain at the deepest exposed structural levels by Upper Cretaceous metasedimentary rocks, which may have been emplaced as a result of trench side underplating or intraarc burial. These results further our understanding of the mechanisms of material transport within the continental lithosphere along Cordilleran subduction margins.

Large quaternary landslides in the central appalachian valley and ridge province near Petersburg, West Virginia

USGS Publications Warehouse

Southworth, C. Scott

1988-01-01

Geological mapping and photointerpretation of side-looking airborne radar images and color-infrared aerial photographs reveal two large Quaternary landslides in the Valley and Ridge province of the central Appalachians near Petersburg, W. Va. The Elkhorn Mountain rock avalanche occurs on the thrust-faulted northwestern flank of the Elkhorn Mountain anticlinorium. A minimum of 7 ?? 106 m3 of quartzite colluvium was transported more than 3 km from a 91 m high escarpment of Silurian Tuscarora Quartzite. The extensively vegetated deposit may owe, in part, its transport and weathering to periglacial conditions during the Pleistocene. In contrast, the Gap Mountain rock block slide is a single allochthonous block that is 1.2 km long, 0.6 km wide, and at least 60 m thick. The 43 ?? 106 m3 block is composed of limestone of the Helderberg Group and the Oriskany Sanstone of Early Devonian age. Planar detachment probably occurred along a dissolution bedding plane near the Shriver Chert and the Oriskany Sandstone contact. Failure probably was initiated by downcutting of the South Branch Potomac River during the Pleistocene. Landslides of this magnitude suggest accelerated erosion during periglacial climates in the Pleistocene. The recognition of these large slope failures may provide evidence of paleoclimatic conditions and, thereby, increase our understanding of the geomorphologic development of the Valley and Ridge province. ?? 1988.

Geologic implications of new zircon U-Pb ages from the White Mountain Peak Metavolcanic Complex, eastern California

NASA Astrophysics Data System (ADS)

Scherer, Hannah H.; Ernst, W. G.; Brooks Hanson, R.

2008-04-01

The NNW-trending White-Inyo Range includes intrusive and volcanic rocks on the eastern flank of the Sierran volcano-plutonic arc. The NE-striking, steeply SE-dipping Barcroft reverse fault separates folded, metamorphosed Mesozoic White Mountain Peak mafic and felsic volcanic flows, volcanogenic sedimentary rocks, and minor hypabyssal plugs on the north from folded, well-bedded Neoproterozoic-Cambrian marble and siliciclastic strata on the south. The 163 ± 2 Ma Barcroft Granodiorite rose along this fault, and thermally recrystallized its wall rocks. However, new SHRIMP-RG ages of magmatic zircons from three White Mountain Peak volcanogenic metasedimentary rocks and a metafelsite document stages of effusion at ˜115-120 Ma as well as at ˜155-170 Ma. The U-Pb data confirm the interpretation by Hanson et al. (1987) that part of the metasedimentary-metavolcanic pile was laid down after Late Jurassic intrusion of the Barcroft pluton. The Lower Cretaceous, largely volcanogenic metasedimentary section lies beneath a low-angle thrust fault, the upper plate of which includes interlayered Late Jurassic mafic and felsic metavolcanic rocks and the roughly coeval Barcroft pluton. Late Jurassic and Early Cretaceous volcanism in this sector of the Californian continental margin, combined with earlier petrologic, structural, and geochronologic studies, indicates that there was no gap in igneous activity at this latitude of the North American continental margin.

Detrital record of initial basement exhumation along the Laramide deformation front, southern Rocky Mountains

NASA Astrophysics Data System (ADS)

Bush, Meredith A.; Horton, Brian K.; Murphy, Michael A.; Stockli, Daniel F.

2016-09-01

New geochronological constraints on upper crustal exhumation in the southern Rocky Mountains help delineate the latest Cretaceous-Paleogene history of drainage reorganization and landscape evolution during Laramide flat-slab subduction beneath western North America. Detrital zircon U-Pb results for the Raton basin of southern Colorado and northern New Mexico define the inception of coarse-grained siliciclastic sedimentation and a distinctive shift in provenance, from distal to proximal sources, that recorded shortening-related uplift and unroofing along the Laramide deformation front of the northern Sangre de Cristo Mountains. This Maastrichtian-early Paleocene ( 70-65 Ma) change—from distal foreland accumulation of sediment derived from the thin-skinned Cordilleran (Sevier) fold-thrust belt to coarse-grained sedimentation proximal to a Laramide basement block uplift—reflects cratonward (eastward) deformation advance and reorganization of drainage systems that supplied a large volume of Paleocene-lower Eocene sediments to the Gulf of Mexico. The timing of unroofing along the eastern deformation front is synchronous with basement-involved shortening across the interior of the Laramide province, suggesting abrupt wholesale uplift rather than a systematic inboard advance of deformation. The growth and infilling of broken foreland basins within the interior and margins of the Laramide province had a significant impact on continental-scale drainage systems, as several ponded/axial Laramide basins trapped large volumes of sediment and induced reorganization of major source-to-sink sediment pathways.

Geology of the Harpers Ferry Quadrangle, Virginia, Maryland, and West Virginia

USGS Publications Warehouse

Southworth, Scott; Brezinski, David K.

1996-01-01

The Harpers Ferry quadrangle covers a portion of the northeast-plunging Blue Ridge-South Mountain anticlinorium, a west-verging allochthonous fold complex of the late Paleozoic Alleghanian orogeny. The core of the anticlinorium consists of high-grade paragneisses and granitic gneisses that are related to the Grenville orogeny. These rocks are intruded by Late Proterozoic metadiabase and metarhyolite dikes and are unconformably overlain by Late Proterozoic metasedimentary rocks of the Swift Run Formation and metavolcanic rocks of the Catoctin Formation, which accumulated during continental rifting of Laurentia (native North America) that resulted in the opening of the Iapetus Ocean. Lower Cambrian metasedimentary rocks of the Loudoun, Weverton, Harpers, and Antietam Formations and carbonate rocks of the Tomstown Formation were deposited in the rift-to-drift transition as the early Paleozoic passive continental margin evolved. The Short Hill fault is an early Paleozoic normal fault that was contractionally reactivated as a thrust fault and folded in the late Paleozoic. The Keedysville detachment is a folded thrust fault at the contact of the Antietam and Tomstown Formations. Late Paleozoic shear zones and thrust faults are common. These rocks were deformed and metamorphosed to greenschist-facies during the formation of the anticlinorium. The Alleghanian deformation was accompanied by a main fold phase and a regional penetrative axial plane cleavage, which was followed by a minor fold phase with crenulation cleavage. Early Jurassic diabase dikes transected the anticlinorium during Mesozoic continental rifting that resulted in the opening of the Atlantic Ocean. Cenozoic deposits that overlie the bedrock include bedrock landslides, terraces, colluvium, and alluvium.

Controls on the deposition and preservation of the Cretaceous Mowry Shale and Frontier Formation and equivalents, Rocky Mountain region, Colorado, Utah, and Wyoming

USGS Publications Warehouse

Kirschbaum, Mark A.; Mercier, Tracey J.

2013-01-01

Regional variations in thickness and facies of clastic sediments are controlled by geographic location within a foreland basin. Preservation of facies is dependent on the original accommodation space available during deposition and ultimately by tectonic modification of the foreland in its postthrusting stages. The preservation of facies within the foreland basin and during the modification stage affects the kinds of hydrocarbon reservoirs that are present. This is the case for the Cretaceous Mowry Shale and Frontier Formation and equivalent strata in the Rocky Mountain region of Colorado, Utah, and Wyoming. Biostratigraphically constrained isopach maps of three intervals within these formations provide a control on eustatic variations in sea level, which allow depositional patterns across dip and along strike to be interpreted in terms of relationship to thrust progression and depositional topography. The most highly subsiding parts of the Rocky Mountain foreland basin, near the fold and thrust belt to the west, typically contain a low number of coarse-grained sandstone channels but limited sandstone reservoirs. However, where subsidence is greater than sediment supply, the foredeep contains stacked deltaic sandstones, coal, and preserved transgressive marine shales in mainly conformable successions. The main exploration play in this area is currently coalbed gas, but the enhanced coal thickness combined with a Mowry marine shale source rock indicates that a low-permeability, basin-centered play may exist somewhere along strike in a deep part of the basin. In the slower subsiding parts of the foreland basin, marginal marine and fluvial sandstones are amalgamated and compartmentalized by unconformities, providing conditions for the development of stratigraphic and combination traps, especially in areas of repeated reactivation. Areas of medium accommodation in the most distal parts of the foreland contain isolated marginal marine shoreface and deltaic sandstones that were deposited at or near sea level lowstand and were reworked landward by ravinement and longshore currents by storms creating stratigraphic or combination traps enclosed with marine shale seals. Paleogeographic reconstructions are used to show exploration fairways of the different play types present in the Laramide-modified, Cretaceous foreland basin. Existing oil and gas fields from these plays show a relatively consistent volume of hydrocarbons, which results from the partitioning of facies within the different parts of the foreland basin.

Measuring crustal deformation in the American West

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jordan, T.H.; Minster, J.B.

1988-08-01

The crust of the western US is deforming as the Pacific and North American plates slide past each other along the San Andreas Fault, the Great Basin is spreading apart, and mountains are being thrust up along the California coast. Monitoring of these processes over the years has resulted in the San Andreas discrepancy, the mismatch between the rate and direction of horizontal slippage along the fault and the relative motion of the Pacific and North American plates.This process will soon be measured directly using the new developed technique of space geodesy, which uses radio waves from quasars or satellitesmore » to measure between fixed stations with an accuracy of a few centimeters.« less

Quantifying Vertical Exhumation in Intracontinental Strike-Slip Faults: the Garlock fault zone, southern California

NASA Astrophysics Data System (ADS)

Chinn, L.; Blythe, A. E.; Fendick, A.

2012-12-01

New apatite fission-track ages show varying rates of vertical exhumation at the eastern terminus of the Garlock fault zone. The Garlock fault zone is a 260 km long east-northeast striking strike-slip fault with as much as 64 km of sinistral offset. The Garlock fault zone terminates in the east in the Avawatz Mountains, at the intersection with the dextral Southern Death Valley fault zone. Although motion along the Garlock fault west of the Avawatz Mountains is considered purely strike-slip, uplift and exhumation of bedrock in the Avawatz Mountains south of the Garlock fault, as recently as 5 Ma, indicates that transpression plays an important role at this location and is perhaps related to a restricting bend as the fault wraps around and terminates southeastward along the Avawatz Mountains. In this study we complement extant thermochronometric ages from within the Avawatz core with new low temperature fission-track ages from samples collected within the adjacent Garlock and Southern Death Valley fault zones. These thermochronometric data indicate that vertical exhumation rates vary within the fault zone. Two Miocene ages (10.2 (+5.0/-3.4) Ma, 9.0 (+2.2/-1.8) Ma) indicate at least ~3.3 km of vertical exhumation at ~0.35 mm/yr, assuming a 30°C/km geothermal gradient, along a 2 km transect parallel and adjacent to the Mule Spring fault. An older Eocene age (42.9 (+8.7/-7.3) Ma) indicates ~3.3 km of vertical exhumation at ~0.08 mm/yr. These results are consistent with published exhumation rates of 0.35 mm/yr between ~7 and ~4 Ma and 0.13 mm/yr between ~15 and ~9 Ma, as determined by apatite fission-track and U-Th/He thermochronometry in the hanging-wall of the Mule Spring fault. Similar exhumation rates on both sides of the Mule Spring fault support three separate models: 1) Thrusting is no longer active along the Mule Spring fault, 2) Faulting is dominantly strike-slip at the sample locations, or 3) Miocene-present uplift and exhumation is below detection levels using apatite fission-track thermochronometry. In model #1 slip on the Mule Spring fault may have propagated towards the range front, and may be responsible for the fault-propagation-folding currently observed along the northern branch of the Southern Death Valley fault zone. Model #2 may serve to determine where faulting has historically included a component of thrust faulting to the east of sample locations. Model #3 would further determine total offset along the Mule Spring fault from Miocene-present. Anticipated fission-track and U-Th/He data will help distinguish between these alternative models.

The regional structural setting of the 2008 Wells earthquake and Town Creek Flat Basin: implications for the Wells earthquake fault and adjacent structures

USGS Publications Warehouse

Henry, Christopher S.; Colgan, Joseph P.

2011-01-01

The 2008 Wells earthquake occurred on a northeast-striking, southeast-dipping fault that is clearly delineated by the aftershock swarm to a depth of 10-12 km below sea level. However, Cenozoic rocks and structures around Wells primarily record east-west extension along north- to north-northeast-striking, west-dipping normal faults that formed during the middle Miocene. These faults are responsible for the strong eastward tilt of most basins and ranges in the area, including the Town Creek Flat basin (the location of the earthquake) and the adjacent Snake Mountains and western Windermere Hills. These older west-dipping faults are locally overprinted by a younger generation of east-dipping, high-angle normal faults that formed as early as the late Miocene and have remained active into the Quaternary. The most prominent of these east-dipping faults is the set of en-échelon, north-striking faults that bounds the east sides of the Ruby Mountains, East Humboldt Range, and Clover Hill (about 5 km southwest of Wells). The northeastern-most of these faults, the Clover Hill fault, projects northward along strike toward the Snake Mountains and the approximately located surface projection of the Wells earthquake fault as defined by aftershock locations. The Clover Hill fault also projects toward a previously unrecognized, east-facing Quaternary fault scarp and line of springs that appear to mark a significant east-dipping normal fault along the western edge of Town Creek Flat. Both western and eastern projections may be northern continuations of the Clover Hill fault. The Wells earthquake occurred along this east-dipping fault system. Two possible alternatives to rupture of a northern continuation of the Clover Hill fault are that the earthquake fault (1) is antithetic to an active west-dipping fault or (2) reactivated a Mesozoic thrust fault that dips east as a result of tilting by the west-dipping faults along the west side of the Snake Mountains. Both alternatives are precluded by the depths of the earthquake and aftershocks, about 8 km and as deep as 12 km, respectively. These depths are below where an antithetic fault would intersect any main fault, and a tilted, formerly shallow and sub-horizontal thrust fault would not extend to depths of more than about 5–6 km. The east-dipping, high-angle, earthquake fault cuts older west-dipping faults rather than reactivating them, highlighting a change in the structural style of Basin and Range extension in this region from closely-spaced, west-dipping faults that rotated significantly during slip and accommodated large-magnitude extension, to widely-spaced, high-angle faults that accommodate much less total strain over a long time span.

Miocene volcanism in the Oaş-Gutâi Volcanic Zone, Eastern Carpathians, Romania: Relationship to geodynamic processes in the Transcarpathian Basin

NASA Astrophysics Data System (ADS)

Kovacs, Marinel; Seghedi, Ioan; Yamamoto, Masatsugu; Fülöp, Alexandrina; Pécskay, Zoltán; Jurje, Maria

2017-12-01

We present the first comprehensive study of Miocene volcanic rocks of the Oaş-Gutâi Volcanic Zone (OGVZ), Romania, which are exposed in the eastern Transcarpathian Basin (TB), within the Eastern Alpine-Western Carpathian-Northern Pannonian (ALCAPA) block. Collision between the ALCAPA block and Europe at 18-16 Ma produced the Carpathian fold-and-thrust belt. This was followed by clockwise rotation and an extensional regime forming core complexes of the separated TB fragment. Based on petrographic and geochemical data, including Srsbnd Nd isotopic compositions and Ksbnd Ar ages, we distinguish three types of volcanic activity in the OGVZ: (1) early Miocene felsic volcanism that produced caldera-related ignimbrites in the Gutâi Mountains (15.4-14.8 Ma); (2) widespread middle-late Miocene intermediate/andesitic volcanism (13.4-7.0 Ma); and (3) minor late Miocene andesitic/rhyolitic volcanism comprising the Oraşu Nou rhyolitic volcano and several andesitic-dacitic domes in the Oaş Mountains (11.3-9.5 Ma). We show that magma evolution in the OGVZ was controlled by assimilation-fractional crystallization and magma-mixing processes within an interconnected multi-level crustal magmatic reservoir. The evolution of volcanic activity within the OGVZ was controlled by the geodynamics of the Transcarpathian Basin. The early felsic and late intermediate Miocene magmas were emplaced in a post-collisional setting and were derived from a mantle source region that was modified by subduction components (dominantly sediment melts) and lower crust. The style of volcanism within the eastern TB system exhibits spatial variations, with andesitic composite volcanoes (Gutâi Mountains) observed at the margins, and isolated andesitic-rhyolitic monogenetic volcanoes (Oaş Mountains) in the center of the basin.

Precambrian basement geologic map of Montana; an interpretation of aeromagnetic anomalies

USGS Publications Warehouse

Sims, P.K.; O'Neill, J. M.; Bankey, Viki; Anderson, E.

2004-01-01

Newly compiled aeromagnetic anomaly data of Montana, in conjunction with the known geologic framework of basement rocks, have been combined to produce a new interpretive geologic basement map of Montana. Crystalline basement rocks compose the basement, but are exposed only in the cores of mountain ranges in southwestern Montana. Principal features deduced from the map are: (1) A prominent northeast-trending, 200-km-wide zone of spaced negative anomalies, which extends more than 700 km from southwestern Montana's Beaverhead Mountains to the Canadian border and reflects suturing of the Archean Mexican Hat Block against the Archean Wyoming Province along the Paleoproterozoic Trans-Montana Orogen (new name) at about 1.9-1.8 Ga; (2) North-northwest-trending magnetic lows in northeastern Montana, which reflect the 1.9-1.8 Ga Trans-Hudson Orogen and truncate the older Trans-Montana Zone; and (3) Subtle northwest- and west-trending negative anomalies in central and western Montana, which represent the northernmost segment of brittle-ductile transcurrent faults of the newly recognized Mesoproterozoic Trans-Rocky Mountain fault system. Structures developed in the Proterozoic provided zones of crustal weakness reactivated during younger Proterozoic and Phanerozoic igneous and tectonic activity. For example, the Trans-Montana Zone guided basement involved thrust faulting in southwestern Montana during the Sevier Orogeny. The Boulder Batholith and associated ore deposits and the linear belt of alkaline intrusions to the northeast were localized along a zone of weakness between the Missouri River suture and the Dillon shear zone of the Trans-Montana Orogen. The northwest-trending faults of Trans-Rocky Mountain system outline depocenters for sedimentary rocks in the Belt Basin. This fault system provided zones of weakness that guided Laramide uplifts during basement crustal shortening. Northwest-trending zones have been locally reactivated during Neogene basin-range extension.

Seismotectonics of the Hindukush and Baluchistan arc

NASA Astrophysics Data System (ADS)

Verma, R. K.; Mukhopadhyay, M.; Bhanja, A. K.

1980-07-01

A seismicity map of that part of the Pakistan-Afghanistan region lying between the latitudes 28° to 38°N and longitudes 66° to 75°E is given using all available data for the period 1890-1970. The earthquakes of magnitude 4.5 and above were considered in the preparation of this map. On the basis of this map, it is observed that the seismicity pattern over the well-known Hindukush region is quite complex. Two prominent, mutually orthogonal, seismicity lineaments, namely the northvestern and the north-eastern trends, characterize the Hindukush area. The northwestern trend appears to extend from the Main Boundary Fault of the Kashmir Himalaya on the southeast to the plains of the Amu Darya in Uzbekistan on the northwest beyond the Hindukush. The Sulaiman and Kirthar ranges of Pakistan are well-defined zones of intermontane seismicity exhibiting north-south alignment. Thirty-two new focal-mechanism solutions for the above-mentioned region have been determined. These, together with the results obtained by earlier workers, suggest the pre-dominance of strike-slip faulting in the area. The Hazara Mountains, the Sulaiman wrench zone and the Kirthar wrench zone, as well as the supposed extension of the Murray ridge up to the Karachi coast, appear to be mostly undergoing strike-slip movements. In the Hindukush region, thrust and strike-slip faulting are found to be equally prevalent. Almost all the thrust-type mechanisms belonging to the Hindukush area have both the nodal planes in the NW-SE direction for shallow as well as intermediate depth earthquakes. The dip of P-axes for the events indicating thrust type mechanisms rarely exceeds 35°. The direction of the seismic slip vector obtained through thrust type solutions is always directed towards the northeast. The epicentral pattern together with these results suggest a deep-seated fault zone paralleling the northwesterly seismic zone underneath the Hindukush. This NW-lineament has a preference for thrust faulting, and it appears to extend from the vicinity of the Main Boundary Fault of the Kashmir Himalaya on the southeast of Uzbekistan on the northwest through Hindukush. Almost orthogonal to this NW-seismic zone, there is a NE-seismic lineament in which there is a preference for strike-slip faulting. The above results are discussed from the point of view of convergence of the Indian and Eurasian plates in the light of plate tectonics theory.

The Chunky Gal Mountain fault-detachment-normal fault providing evidence for Early-to-Middle Paleozoic extensional unroofing of the eastern Blue Ridge, or folded thrust

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hatcher, R.D. Jr.

1993-03-01

The Chunky Gal Mountain fault (CGMF), located in the western Blue Ridge of southern NC and northern GA, contains unequivocal evidence for hanging wall-down-to-the-west movement. The 50 m-thick fault zone here consists of a series of shear zones in the footwall in a mass of mylonitized garnet-rich biotite gneiss. The main contact with the hanging wall reveals both a contrast in rock type and truncation of fabrics. Above the fault are amphibolite, ultramafic rocks, and minor metasandstone and pelitic schist of the Buck Creek mafic-ultramafic complex, while the footwall contains complexly folded metasandstone, pelitic schist, and calcsilicate pods of themore » Coleman River Formation. In the present orientation, the mylonitic foliation in the footwall rocks of the GGMF is subvertical; foliation in the hanging wall is subhorizontal at road level. These rocks were metamorphosed to upper amphibolite facies assemblages, and, after emplacement of the CGMF, were cut by brittle faults and trondhjemite dikes that contain no obvious tectonic fabric. Movement on the CGMF occurred near the thermal peak because enough heat remained in the rocks after movement to statically anneal the mylonite microfabric, but mesoscopic rotated porphyroclasts, rotated (dragged) earlier foliation, and some S-C fabrics clearly indicate the shear sense and vergence of this structure. Shear zones related to the CGMF transposed earlier fabrics, although some relicts preserving earlier structures remain in the shear zones. These rotated but untransposed relicts of amphibolite and garnet-rich biotite gneiss mylonite may indicate locally higher strain rates in subsidiary shear zones. The thermal/mechanical properties of the CGMF make it difficult to connect to the Shope Fork or Soque River thrusts farther south and east. Thus the hanging-wall-down configuration provides an alternative hypothesis that the CGMF may be a detachment-normal fault related to Taconian extensional unroofing of the Appalachians.« less

Paleogeodesy of the Southern Santa Cruz Mountains Frontal Thrusts, Silicon Valley, CA

NASA Astrophysics Data System (ADS)

Aron, F.; Johnstone, S. A.; Mavrommatis, A. P.; Sare, R.; Hilley, G. E.

2015-12-01

We present a method to infer long-term fault slip rate distributions using topography by coupling a three-dimensional elastic boundary element model with a geomorphic incision rule. In particular, we used a 10-m-resolution digital elevation model (DEM) to calculate channel steepness (ksn) throughout the actively deforming southern Santa Cruz Mountains in Central California. We then used these values with a power-law incision rule and the Poly3D code to estimate slip rates over seismogenic, kilometer-scale thrust faults accommodating differential uplift of the relief throughout geologic time. Implicit in such an analysis is the assumption that the topographic surface remains unchanged over time as rock is uplifted by slip on the underlying structures. The fault geometries within the area are defined based on surface mapping, as well as active and passive geophysical imaging. Fault elements are assumed to be traction-free in shear (i.e., frictionless), while opening along them is prohibited. The free parameters in the inversion include the components of the remote strain-rate tensor (ɛij) and the bedrock resistance to channel incision (K), which is allowed to vary according to the mapped distribution of geologic units exposed at the surface. The nonlinear components of the geomorphic model required the use of a Markov chain Monte Carlo method, which simulated the posterior density of the components of the remote strain-rate tensor and values of K for the different mapped geologic units. Interestingly, posterior probability distributions of ɛij and K fall well within the broad range of reported values, suggesting that the joint use of elastic boundary element and geomorphic models may have utility in estimating long-term fault slip-rate distributions. Given an adequate DEM, geologic mapping, and fault models, the proposed paleogeodetic method could be applied to other crustal faults with geological and morphological expressions of long-term uplift.

Early Mesozoic history and petroleum potential of formations in Wyoming and northern Utah

DOE Office of Scientific and Technical Information (OSTI.GOV)

Picard, M.D.

1993-08-01

During the Triassic and Jurassic, over what is now Wyoming and northern Utah, roughly equal amounts of sediment were being deposited in continental settings-lake, stream, and eolian-and in shallow-marine or deltaic-plain settings-delta, beach, marsh, tidal flat, and shallow shelf. Clastic rocks dominate. In order of decreasing abundance, the rocks are fine-grained clastics (siltstone, claystone, mudstone), sandstone, carbonates, evaporites, and claystone- and carbonate-pebble conglomerate. Approximately four-fifths of the succession contains red beds or variegated layers-purple, maroon, lavender, olive, green. Unconformities bound Jurassic formations in Wyoming-Nugget, Gypsum Spring, Sundance, and Morrison. Unconformities also bound the continental Upper Triassic section-unnamed red bed unit,more » Jelm, Popo Agie-separating it from the underlying shallow-marine formations-Dinwoody, Red Peak, Alcova, Crow Mountain. Within the marine sequence, an unconformity occurs at the top of the Alcova and, quite likely, shorter periods of erosion took place at the top and below the base of the sandy faces that underlies the Alcova. The postulate duration of the principal unconformities totals about 18 m.y., at least one-sixth of early Mesozoic time. The bulk of the remaining 80-100 m.y. may be represented by a large number of smaller unconformities. For the lower Mesozoic, as for most stratigraphic intervals, a few beds contain the story of what has taken place during the abyss of geologic time. Like other places in the world where evaporites occur in the Triassic, the Wyoming section produces little crude oil. No significant sequence in the early Mesozoic shows source-bed characteristics. The Crow Mountain Sandstone contains the best reservoirs. The Lower( ) Jurassic Nugget Sandstone produces the most oil and gas in the thrust belt of southwestern Wyoming and northern Utah. Cretaceous claystones below the thrusts contain the source beds.« less

Controls on size and occurrence of the largest sub-aerial landslide on Earth: Seymareh (Saidmarreh) landslide, Zagros fold-thrust belt, Iran

NASA Astrophysics Data System (ADS)

Roberts, N. J.; Evans, S. G.

2009-12-01

Gigantic (> 1 Gm3) landslides are high-magnitude, low-frequency extremes of mass movements. They are important factors in topographic evolution and hazard in mountain regions due to their magnitude. However, few examples exist for study because of their infrequency. Consequently, controls on the location and size gigantic landslides remain poorly understood. Re-examination of the Seymareh (Saidmarreh) rock avalanche, Zagros fold-thrust belt, shows it to be the largest sub-aerial landslide on Earth (initial failure volume 38 Gm3), thus representing the upper magnitude limit for terrestrial landslides. Detailed examination of the source area (including orbital remote sensing, geotechnical investigation and structural mapping) provides new insights into controls on the size and mobility of gigantic landslides. The gigantic Early Holocene rockslide initiated on the northeast limb of Kabir Kuh, the largest anticline in the Zagros fold-thrust belt, and involved the simultaneous failure of a rock mass measuring 15 km along strike. The rockslide transformed into a rock avalanche that ran-out 19.0 km, filling two adjacent valleys and overtopping an intervening low mountain ridge. The failure involved 220 m of competent jointed limestone (Asmari Formation) underlain by 580 m of weaker mudrock-dominated units. Geologic structure, geomechanical strength and topography of the source slope strongly controlled failure initiation. Extreme landslide dimensions resulted in part from extensive uniform pre-failure stability, produced by structural and topographic features related to the large scale of the Kabir Kuh anticline. High continuity bedding planes determined the large lateral extent along strike. Bedding normal joints, the breached nature of the anticline and fluvial undercutting at the slope toe accommodated expansive lateral, headscarp and toe release, respectively, necessary for extensive failure. Geomechanically weak units at depth aided the penetration of the failure surface into the source slope while low bedding dip (ca. 19°) allowed kinematic freedom of a particularly thick sequence to move downslope. Prevention of gradual rockmass removal by smaller-magnitude, more frequent denudation ensured its preservation for later simultaneous failure. The overall failure surface (11°) cut across weaker beds and finally breached the Asmari carapace by break-out at the base of the source slope. Relative relief of the source slope on Kabir Kuh was modest (1350 m on average) indicating that uniform structural and topographic conditions along strike, shallow bedding dips, and the geomechnical properties of the source rock mass were more important in determining the magnitude of the landslide that forms the upper magnitude limit for subaerial landslides.

Analogue modeling of 3-D structural segmentation in fold-and-thrust belts: interactions between frictional and viscous provinces in foreland basins

NASA Astrophysics Data System (ADS)

Borderie, Sandra; Graveleau, Fabien; Witt, César; Vendeville, Bruno C.

2016-04-01

Accretionary wedges are generally segmented both across and along strike because of diverse factors including tectonic and stratigraphic inheritance. In fold-and-thrust belts, along-strike stratigraphic changes in the foreland sequence are classically observed and cause a curvature of the deformation front. Although the parameters controlling this curvature are well documented, the structural interactions and mutual influences between adjacent provinces are much less analyzed. To investigate this question, we deformed analogue models in a compressional box equipped with digital cameras and a topographic measurement apparatus. Models where shortened above a basal frictional detachment (glass microbeads) and segmentation was tested by having a region in which we added an interbedded viscous level (silicone polymer) within the sedimentary cover (dry sand). By changing the number (2 or 3) and the relative width of the purely frictional and viscous provinces, our goal was to characterize geometrically and kinematically the interactions between the viscous and the purely frictional provinces. We used a commercial geomodeller to generate 3-D geometrical models. The results indicate that regardless of the relative width of the purely frictional vs. viscous provinces, the deformation style in the frictional province is not influenced by the presence of the adjacent viscous province. On the contrary, the structural style and the deformation kinematics in the viscous province is significantly impacted by the presence or absence of an adjacent purely frictional province. At first order, the deformation style in the viscous province depends on its width, and three structural styles can be defined along strike. Far from the frictional area, structures are primarily of salt-massif type, and they do not seem to be influenced by the frictional wedge province. Towards the frictional province, deformation changes gradually to a zone of purely forethrusts (foreland verging), and finally to a highly faulted zone with both fore- and backthrusts (hinterland verging). In addition, a kinematic analysis indicates that narrow viscous provinces are strongly influenced by the presence of an adjacent frictional province. Indeed, propagation of shallow thrusts occurs in sequence and the deformation front reaches lately the external décollement pinchout. On the contrary, the deformation front of the wide viscous provinces propagates rapidly to the external décollement pinchout, then younger thrusts form out of sequence. Along-strike segmentation also affects the deep structures (thrusts detaching on the basal frictional décollement). In the viscous province, the presence of an upper viscous décollement opposes the advance of the basal deformation front. There, the rear of the wedge is characterized by imbrications of thrusts sheets (antiformal stacks), and the deep deformation front is convex towards the hinterland. Our experiments allow to better understand the dynamics of salt-controlled fold-and-thrust belts such as in the Huallaga (Peru) and Kuqa (China) basins or the Franklin Mountains (NW Canada).

Thermal State, Slab Metamorphism, and Interface Seismicity in the Cascadia Subduction Zone Based On 3-D Modeling

NASA Astrophysics Data System (ADS)

Ji, Yingfeng; Yoshioka, Shoichi; Banay, Yuval A.

2017-09-01

Giant earthquakes have repeatedly ruptured the Cascadia subduction zone, and similar earthquakes will likely also occur there in the near future. We employ a 3-D time-dependent thermomechanical model that incorporates an up-to-date description of the slab geometry to study the Cascadia subduction thrust. Results show a distinct band of 3-D slab dehydration that extends from Vancouver Island to the Seattle Basin and farther southward to the Klamath Mountains in northern California, where episodic tremors cluster. This distribution appears to include a region of increased dehydration in northern Cascadia. The phenomenon of heterogeneous megathrust seismicity associated with oblique subduction suggests that the presence of fluid-rich interfaces generated by slab dehydration favors megathrust seismogenesis in the northern part of this zone. The thin, relatively weakly metamorphosed Explorer, Juan de Fuca, and Gorda Plates are associated with an anomalous lack of thrust earthquakes, and metamorphism that occurs at temperatures of 500-700°C near the Moho discontinuity may represent a key factor in explaining the presence of the associated episodic tremor and slip (ETS), which requires a young oceanic plate to subduct at a small dip angle, as is the case in Cascadia and southwestern Japan. The 3-D intraslab dehydration distribution suggests that the metamorphosed plate environment is more complex than had previously been believed, despite the existence of channeling vein networks. Slab amphibolization and eclogitization near the continental Moho depth is thus inferred to account for the resultant overpressurization at the interface, facilitating the generation of ETS and the occurrence of small to medium thrust earthquakes beneath Cascadia.

Tectonic interpretations of Central Ishtar Terra (Venus) from Venera 15/16 and Magellan full-resolution radar images

NASA Astrophysics Data System (ADS)

Ansan, V.; Vergely, P.; Masson, P.

1994-03-01

For more than a decade, the mapping of Venus has revealed a surface that has had a complex volcanic and tectonic history, especially in the northern latitudes. Detailed morphostructural analysis and tectonic interpretations of Central Ishtar Terra, based both on Venera 15/16 and Magellan full-resolution radar images, have provided additional insight to the formation and evolution of Venusian terrains. Ishtar Terra, centered at 0 deg E longitude and 62 deg N latitude, consists of a broad high plateau, Lakshmi Planum, partly surrounded by two highlands, Freyja and Maxwell Montes, which have been interpreted as orogenic belts based on Venera 15 and 16 data. Lakshmi Planum, the oldest part of Ishtar Terra, is an extensive and complexly fractured plateau that can be compared to a terrestrial craton. The plateau is partially covered by fluid lava flows similar to the Deccan traps in India, which underwent a late stage of extensional fracturing. After the extensional deformation of Lakshmi Planum, Freyja and Maxwell Montes were created by regional E-W horizontal shortening that produced a series of N-S folds and thrusts. However, this regional arrangement of folds and thrusts is disturbed locally, e.g. the compressive deformation of Freyja Montes was closely controlled by parallel WNW-ESE-trending left-lateral shear zones and the northwestern part of Maxwell Montes seems to be extruded laterally to the southwest, which implies a second oblique thrust front overlapping Lakshmi Planum. These mountain belts also shows evidence of a late volcanic stage and a subsequent period of relaxation that created grabens parallel to the highland trends, especially in Maxwell Montes.

Influence of pre-existing basement faults on the structural evolution of the Zagros Simply Folded belt: 3D numerical modelling

NASA Astrophysics Data System (ADS)

Ruh, Jonas B.; Gerya, Taras

2015-04-01

The Simply Folded Belt of the Zagros orogen is characterized by elongated fold trains symptomatically defining the geomorphology along this mountain range. The Zagros orogen results from the collision of the Arabian and the Eurasian plates. The Simply Folded Belt is located southwest of the Zagros suture zone. An up to 2 km thick salt horizon below the sedimentary sequence enables mechanical and structural detachment from the underlying Arabian basement. Nevertheless, deformation within the basement influences the structural evolution of the Simply Folded Belt. It has been shown that thrusts in form of reactivated normal faults can trigger out-of-sequence deformation within the sedimentary stratigraphy. Furthermore, deeply rooted strike-slip faults, such as the Kazerun faults between the Fars zone in the southeast and the Dezful embayment and the Izeh zone, are largely dispersing into the overlying stratigraphy, strongly influencing the tectonic evolution and mechanical behaviour. The aim of this study is to reveal the influence of basement thrusts and strike-slip faults on the structural evolution of the Simply Folded Belt depending on the occurrence of intercrustal weak horizons (Hormuz salt) and the rheology and thermal structure of the basement. Therefore, we present high-resolution 3D thermo-mechnical models with pre-existing, inversively reactivated normal faults or strike-slip faults within the basement. Numerical models are based on finite difference, marker-in-cell technique with (power-law) visco-plastic rheology accounting for brittle deformation. Preliminary results show that deep tectonic structures present in the basement may have crucial effects on the morphology and evolution of a fold-and-thrust belt above a major detachment horizon.

First thermochronological constraints on the Cenozoic extension along the Balkan fold-thrust belt (Central Stara Planina Mountains, Bulgaria)

NASA Astrophysics Data System (ADS)

Kounov, Alexandre; Gerdjikov, Ianko; Vangelov, Dian; Balkanska, Eleonora; Lazarova, Anna; Georgiev, Stoyan; Blunt, Edward; Stockli, Daniel

2017-11-01

The Balkan fold-thrust belt, exposed in Bulgaria and north-east Serbia, is part of the north-east vergent segment of the bi-vergent Eastern Mediterranean Alpine orogen. It was formed during two distinct compressional stages; the first one lasted from the Middle Jurassic to the Early Cretaceous and the second from Late Cretaceous to the Paleogene. Although the compressional tectonic evolution of the Balkan fold-thrust belt since the Middle Jurassic and during most of the Mesozoic is relatively well studied, the final exhumation of the rocks of the belt during the Cenozoic has remained poorly understood. Here, we present the first thermochronological constraints, based on fission-track and [U-Th-(Sm)]/He analysis, showing that along the central part of the belt syn- to post-orogenic extension could have started as early as the middle Eocene. Low-temperature thermochronological analysis of samples collected from three areas reveals at least two phases of increased cooling and exhumation during the Cenozoic. The first exhumation phase took place between 44 and 30 Ma and appears to be related to the syn- to post-orogenic collapse coeval with the earliest Cenozoic extensional stage observed across the southern Balkan Peninsula. A period of relative quiescence (between 30 and 25 Ma) is followed by the next cooling stage, between 25 and 20 Ma, which appears to be related to late Oligocene to early Miocene crustal extension across the Balkan Peninsula. Extension accommodated by the late Miocene to Recent age Sub-Balkan Graben System does not appear to have produced exhumation of rocks from beneath 2-4 km depth, as it was not detected by the low-temperature thermochronological methods applied in this study.

Preliminary geologic map of the Bowen Mountain quadrangle, Grand and Jackson Counties, Colorado

USGS Publications Warehouse

Cole, James C.; Braddock, William A.; Brandt, Theodore R.

2011-01-01

The map shows the geology of an alpine region in the southern Never Summer Mountains, including parts of the Never Summer Wilderness Area, the Bowen Gulch Protection Area, and the Arapaho National Forest. The area includes Proterozoic crystalline rocks in fault contact with folded and overturned Paleozoic and Mesozoic sedimentary rocks and Upper Cretaceous(?) and Paleocene Middle Park Formation. The folding and faulting appears to reflect a singular contractional deformation (post-Middle Park, so probably younger than early Eocene) that produced en echelon structural uplift of the Proterozoic basement of the Front Range. The geologic map indicates there is no through-going \\"Never Summer thrust\\" fault in this area. The middle Tertiary structural complex was intruded in late Oligocene time by basalt, quartz latite, and rhyolite porphyry plugs that also produced minor volcanic deposits; these igneous rocks are collectively referred to informally as the Braddock Peak intrusive-volcanic complex whose type area is located in the Mount Richthofen quadrangle immediately north (Cole and others, 2008; Cole and Braddock, 2009). Miocene boulder gravel deposits are preserved along high-altitude ridges that probably represent former gravel channels that developed during uplift and erosion in middle Tertiary time.

Indentation tectonics in northern Taiwan: insights from field observations and analog models

NASA Astrophysics Data System (ADS)

Lu, Chia-Yu; Lee, Jian-Cheng; Malavieille, Jacques

2017-04-01

In northern Taiwan, contraction, extension, transcurrent shearing, and block rotation are four major tectonic deformation mechanisms involved in the progressive deformation of this arcuate mountain belt. The recent evolution of the orogen is controlled not only by the oblique convergence between the Eurasian plate and the Philippine Sea plate but also by the corner shape of the plate boundary. Based on field observations, analyses, geophysical data (mostly GPS) and results of experimental models, we interpret the curved shape of northern Taiwan as a result of contractional deformation (involving imbricate thrusting and folding, backthrusting and backfolding). The subsequent horizontal and vertical extrusion, combined with increasing transcurrent & rotational deformation (bookshelf-type strike-slip faulting and block rotation) induced transcurrent/ rotational extrusion and extrusion related extensional deformation. A special type of extrusional folds characterizes that complex deformation regime. The tectonics in northern Taiwan reflects a single, regional pattern of deformation. The crescent-shaped mountain belt develops in response to oblique indentation by an asymmetric wedge indenter, retreat of Ryukyu trench and opening of the Okinawa trough. Three sets of analog sandbox models are presented to illustrate the development of tectonic structures and their kinematic evolution

Geochronologic evidence for Late Cretaceous and Miocene tectonism in northern New England

NASA Astrophysics Data System (ADS)

Amidon, W. H.; Barr, M.; Walcott, C.; Kylander-Clark, A. R.

2017-12-01

The persistence of mountainous relief in the northeastern U.S. suggests post-rift tectonic rejuvenation has occurred, although specific mechanisms and timing have been difficult to identify. Here we present direct evidence for significant tectonism in New Hampshire and Vermont during the Late-Cretaceous ( 85-65 Ma) and Miocene periods ( 20-5 Ma). Low temperature thermochronology from a drill core in the White Mountains of New Hampshire suggests 2-3 km of accelerated exhumation during the Late Cretaceous. This exhumation is synchronous with compressional thrusting and rapid exhumation on many other Atlantic margins and also with a change in spreading direction in the Atlantic from 85-65 Ma. Recently obtained U-Pb ages of vein calcite from faults and fractures in the Champlain Valley of New York and Vermont suggest significant brittle fracturing occurred during the Late Cretaceous and also during the Miocene. Although many questions remain, this evidence points to tectonic rejuvenation by lateral tectonic stresses in the latest Cretaceous and possibly in the Miocene. The Late Cretaceous seems to have been a particularly significant tectonic episode in northern New England and elsewhere in the circum-Atlantic region.

High resolution image of uppermost mantle beneath NE Iran continental collision zone

NASA Astrophysics Data System (ADS)

Motaghi, K.; Tatar, M.; Shomali, Z. H.; Kaviani, A.; Priestley, K.

2012-10-01

We invert 3775 relative P wave arrival times using the ACH damped least square method of Aki et al. (1977) to study upper mantle structure beneath the NE Iran continental collision zone. The data for this study were recorded by 17 three component broad-band stations operated from August 2006 to February 2008 along a profile from the center of Iranian Plateau, near Yazd, to the northeastern part of Iran on the Turan Platform just north of the Kopeh Dagh Mountains. The results confirm the previously known low velocity upper mantle beneath Central Iran. Our tomographic model reveals a deep high velocity anomaly. The surficial expressions of this anomaly are between the Ashkabad and Doruneh Faults, where the resolution and ray coverage are good. A transition zone in uppermost mantle is recognized under the Binalud foreland that we interpreted as suture zone between Iran and Turan platform. Our results indicate that Atrak Valley which is the boundary between the Binalud and Kopeh Dagh Mountains can be considered as the northeastern suture of the Iranian Plateau where Eurasia and Turan Platform under-thrust beneath the Binalud range and Central Iran.

Oligocene-Miocene burial and exhumation of the southernmost Gangdese mountains from sedimentary and thermochronological evidence

NASA Astrophysics Data System (ADS)

Ge, Yukui; Li, Yalin; Wang, Xiaonan; Qian, Xinyu; Zhang, Jiawei; Zhou, Aorigele; Liu-Zeng, Jing

2018-01-01

The Kailas conglomerates crop out ubiquitously along the southernmost boundary of the Gangdese batholith. They unconformably overlie the Gangdese batholith and are displaced by the Great Counter thrust (GCT) fault, forming a fault contact with the Xigaze forearc basin, the associated subduction complex and the Tethyan Himalayan sequence. These strata furnish a record of uplift and paleoenvironmental change in the Indus-Yarlung suture zone during the Oligocene-Miocene. Our new and previously published low-temperature thermochronometric data from the Gangdese batholith and the Kailas conglomerates indicate a period of rapid exhumation beginning approximately 17-15 Ma centered on the southern margin of the Gangdese batholith, whereas regional uplift commenced significantly earlier during the deposition of the Kailas conglomerates, based on the presence of an abrupt facies transition from deep-water lacustrine deposits to red alluvial fan or fluvial deposits. The period of rapid exhumation probably lagged behind the initiation of faster uplift, while the related changes in the depositional environment were most likely recorded immediately in the basin stratigraphy. Subsequently, the Kailas conglomerates were buried in association with the development of the north-directed Great Counter thrust, while rapid exhumation was facilitated by efficient incision by the paleo-Yarlung river at approximately 17-15 Ma.

Assessment of undiscovered oil and gas resources of the East Coast Mesozoic basins of the Piedmont, Blue Ridge Thrust Belt, Atlantic Coastal Plain, and New England Provinces, 2011

USGS Publications Warehouse

Milici, Robert C.; Coleman, James L.; Rowan, Elisabeth L.; Cook, Troy A.; Charpentier, Ronald R.; Kirschbaum, Mark A.; Klett, Timothy R.; Pollastro, Richard M.; Schenk, Christopher J.

2012-01-01

During the early opening of the Atlantic Ocean in the Mesozoic Era, numerous extensional basins formed along the eastern margin of the North American continent from Florida northward to New England and parts of adjacent Canada. The basins extend generally from the offshore Atlantic continental margin westward beneath the Atlantic Coastal Plain to the Appalachian Mountains. Using a geology-based assessment method, the U.S. Geological Survey estimated a mean undiscovered natural gas resource of 3,860 billion cubic feet and a mean undiscovered natural gas liquids resource of 135 million barrels in continuous accumulations within five of the East Coast Mesozoic basins: the Deep River, Dan River-Danville, and Richmond basins, which are within the Piedmont Province of North Carolina and Virginia; the Taylorsville basin, which is almost entirely within the Atlantic Coastal Plain Province of Virginia and Maryland; and the southern part of the Newark basin (herein referred to as the South Newark basin), which is within the Blue Ridge Thrust Belt Province of New Jersey. The provinces, which contain these extensional basins, extend across parts of Georgia, South Carolina, North Carolina, Virginia, Maryland, Delaware, Pennsylvania, New Jersey, New York, Connecticut, and Massachusetts.

Syntectonic Fluid-Rock Interactions Involving Surficial Waters in the Sevier Thrust Belt, Tendoy Mountains, Southwest Montana

NASA Astrophysics Data System (ADS)

Johnson, A. C.; Anastasio, D. J.; Bebout, G. E.

2002-05-01

Calcite veins and Mississippian carbonates from the Sevier thrust front record syntectonic meteoric fluid infiltration and hydrocarbon migration. The Tendoy and Four Eyes Canyon thrust sheets were emplaced onto the western margin of the Late Cretaceous Western Interior Seaway \\{WIS\\}. Low salinity \\{Tice = -0.6° C to +3.6° C\\} and low temperature \\{110° C +/- 10\\} fluids interacted with hanging-wall carbonates at a depth of 5km. Most veins have single or multiple generations of varying apertures, composed predominately of large euhedral crystals with some finer grained layers and protolith inclusions. Orientation analysis of mutually cross-cutting, high-angle vein sets suggest development concurrent with Four Eyes Canyon thrusting but prior to Tendoy thrusting. These vein sets are generally cut by later synfolding bed-parallel shear veins. Reactivation of both the bed-parallel and bed-perpendicular vein sets \\{strike parallel and strike perpendicular\\} in the Four Eyes Canyon thrust sheet occurred subsequent to Sevier compression, creating wide, coarse crystalline veins that often transect Sevier structures. Oxygen and Carbon isotope analyses of veins allow for reconstruction of fluid-rock interactions during thrust sheet emplacement and later reactivation. All veins and variably deformed host-rocks were microsampled and analyzed for δ 18OV-SMOW and δ 13CV-PDB. Small Tendoy veins \\{1mm-1cm wide\\} have calcite δ 18O values of +8.9 to +28.8‰ and calculated fluid \\{as H2O\\} of -8.3 to +11.6‰ \\{100° C\\}, -7.3 to +12.6‰ \\{110° C\\}, and -6.3 to +13.6‰ \\{120° C\\}. Four Eyes Canyon veins \\{1cm-3m wide\\} have calcite δ 18O values of +5.9 to +17.0‰ and calculated fluid of -11.3 to -0.2‰ \\{100° C\\}, -10.3 to +0.8‰ \\{110° C\\}, and -9.3 to +1.8‰ \\{120° C\\}. While there is significant variation in δ 18O there is relatively little systematic variation seen in δ 13C. Protolith carbonate has δ 18O values of +22.2‰ +/- 3.2; and some multi-layered veins are more depleted in δ 18O in earlier-formed generations. For three sites in the Lost River Range \\{LRR\\}, Idaho, the calculated minimum fluid δ 18O is -7.5‰ \\{+150 to +250° C\\} \\{Bebout et al., 2001; GRL\\}. Although the uncertainty of the regional temperature is large, when assuming a temperature of 110° C +/- 10 the Tendoy has a minimum calculated δ 18O H2O value of -8.3 to -6.3‰ and the Four Eyes Canyon has a minimum calculated δ 18O H2O value of -11.3 to -9.3‰ . These fluid O-isotope compositions are similar to the minimum H2O δ 18O calculated for the LRR sites - all pointing to infiltration of the thrust sheets by meteoric waters, possibly relatively nearshore meteoric waters with isotopic compositions strongly influenced by the nearby WIS. Surficial fluids possibly infiltrated into the thrust sheets by topographic recharge and migrated updip towards the foreland, mixing to varying degrees with more deeply roused fluids. Smaller veins and longer travel times and distances favored more extensive fluid-rock interaction and thus more rock-controlled fluid compositions. Microfractures in veins healed by hydrocarbons indicate that hydrocarbons migrated with freshwater fluids. Calcite veins record a dynamic history of fluid pathways and fluid flow as permeability evolved during thrust emplacement.

Pre-, syn-, and postcollisional stratigraphic framework and provenance of upper triassic-upper cretaceous strata in the northwestern talkeetna mountains, alaska

USGS Publications Warehouse

Hampton, B.A.; Ridgway, K.D.; O'Neill, J. M.; Gehrels, G.E.; Schmidt, J.; Blodgett, R.B.

2007-01-01

Mesozoic strata of the northwestern Talkeetna Mountains are located in a regional suture zone between the allochthonous Wrangellia composite terrane and the former Mesozoic continental margin of North America (i.e., the Yukon-Tanana terrane). New geologic mapping, measured stratigraphic sections, and provenance data define a distinct three-part stratigraphy for these strata. The lowermost unit is greater than 290 m thick and consists of Upper Triassic-Lower Jurassic mafic lavas, fossiliferous limestone, and a volcaniclastic unit that collectively we informally refer to as the Honolulu Pass formation. The uppermost 75 m of the Honolulu Pass formation represent a condensed stratigraphic interval that records limited sedimentation over a period of up to ca. 25 m.y. during Early Jurassic time. The contact between the Honolulu Pass formation and the overlying Upper Jurassic-Lower Cretaceous clastic marine strata of the Kahiltna assemblage represents a ca. 20 m.y. depositional hiatus that spans the Middle Jurassic and part of Late Jurassic time. The Kahiltna assemblage may to be up to 3000 m thick and contains detrital zircons that have a robust U-Pb peak probability age of 119.2 Ma (i.e., minimum crystallization age/maximum depositional age). These data suggest that the upper age of the Kahiltna assemblage may be a minimum of 10-15 m.y. younger than the previously reported upper age of Valanginian. Sandstone composition (Q-43% F-30% L-27%-Lv-71% Lm-18% Ls-11%) and U-Pb detrital zircon ages suggest that the Kahiltna assemblage received igneous detritus mainly from the active Chisana arc, remnant Chitina and Talkeetna arcs, and Permian-Triassic plutons (Alexander terrane) of the Wrangellia composite terrane. Other sources of detritus for the Kahiltna assemblage were Upper Triassic-Lower Jurassic plutons of the Taylor Mountains batholith and Devonian-Mississippian plutons; both of these source areas are part of the Yukon-Tanana terrane. The Kahiltna assemblage is overlain by previously unrecognized nonmarine strata informally referred to here as the Caribou Pass formation. This unit is at least 250 m thick and has been tentatively assigned an Albian-Cenomanian-to-younger age based on limited palynomorphs and fossil leaves. Sandstone composition (Q-65% F-9% L-26%-Lv-28% Lm-52% Ls-20%) from this unit suggests a quartz-rich metamorphic source terrane that we interpret as having been the Yukon-Tanana terrane. Collectively, provenance data indicate that there was a fundamental shift from mainly arc-related sediment derivation from sources located south of the study area during Jurassic-Early Cretaceous (Aptian) time (Kahiltna assemblage) to mainly continental margin-derived sediment from sources located north and east of the study area by Albian-Cenomanian time (Caribou Pass formation). We interpret the threepart stratigraphy defined for the northwestern Talkeetna Mountains to represent pre- (the Honolulu Pass formation), syn- (the Kahiltna assemblage), and post- (the Caribou Pass formation) collision of the Wrangellia composite terrane with the Mesozoic continental margin. A similar Mesozoic stratigraphy appears to exist in other parts of south-central and southwestern Alaska along the suture zone based on previous regional mapping studies. New geologic mapping utilizing the three-part stratigraphy interprets the northwestern Talkeetna Mountains as consisting of two northwest-verging thrust sheets. Our structural interpretation is that of more localized thrust-fault imbrication of the three-part stratigraphy in contrast to previous interpretations of nappe emplacement or terrane translation that require large-scale displacements. Copyright ?? 2007 The Geological Society of America.

Postobductional extension along and within the Frontal Range of the Eastern Oman Mountains

NASA Astrophysics Data System (ADS)

Mattern, Frank; Scharf, Andreas

2018-04-01

The Oman Mountains formed by late Cretaceous obduction of the Tethys-derived Semail Ophiolite. This study concerns the postobductional extension on the northern flank of the mountain belt. Nine sites at the northern margins of the Jabal Akhdar/Nakhl and Saih Hatat domes of the Eastern Oman ("Hajar") Mountains were investigated. The northern margins are marked by a system of major interconnected extensional faults, the "Frontal Range Fault". While the vertical displacements along the Saih Hatat and westerly located Jabal Nakhl domes measure 2.25-6.25 km, 0.5-4.5 km and 4-7 km, respectively, it amounts to 1-5 km along the Jabal Akhdar Dome. Extension had started during the late Cretaceous, towards the end of ophiolite emplacement. Two stages of extension can be ascertained (late Cretaceous to early Eocene and probably Oligocene) at the eastern part of the Frontal Range Fault System (Wadi Kabir and Fanja Graben faults of similar strike). Along the intervening and differently striking fault segments at Sad and Sunub the same two stages of deformation are deduced. The first stage is characterized again by extension. The second stage is marked by dextral motion, including local transtension. Probable Oligocene extension affected the Batinah Coast Fault while it also affected the Wadi Kabir Fault and the Fanja Graben. It is unclear whether the western portion of the Frontal Range Fault also went through two stages of deformation. Bedding-parallel ductile and brittle deformation is a common phenomenon. Hot springs and listwaenite are associated with dextral releasing bends within the fault system, as well as a basalt intrusion of probable Oligocene age. A structural transect through the Frontal Range along the superbly exposed Wadi Bani Kharous (Jabal Akhdar Dome) revealed that extension affected the Frontal Range at least 2.5 km south of the Frontal Range Fault. Also here, bedding-parallel shearing is important, but not exclusive. A late Cretaceous thrust was extensionally reactivated by a branch fault of the Frontal Range Fault. Extension may be ductile (limestone mylonites), ductile and brittle (ooid deformation, boudinaged belemnite rostra, shear bands) or brittle. Extension is heterogeneously distributed within the Frontal Range. Extension is mainly related to orogenic/gravitational collapse of the Oman Mountains. Collapse may have been associated with isostatic rebound and rise of the two domes. In the western part of the study area, the Frontal Range Fault has a listric morphology. It is probably horizontal at a depth of 15 km below the Batinah coastal area. The fault seems to use the clay- and tuff-bearing Aruma Group as shear horizon. The depth of 15 km may coincide with the brittle-ductile transition of quartz- and feldspar-rich rocks. Close to this depth, the listric Batinah Coast Fault curves into the Frontal Range Fault. Extension along the Frontal Range and Batinah Coast faults probably reactivated preexisting late Cretaceous thrust faults during post-late Eocene time. The latter fault is likely mechanically related to the Wadi Kabir Fault via the Fanja Graben Fault and the Sunub fault segment. Listwaenite and serpentinite cluster preferably around the extensional faults. The Semail Gap probably functioned as a sinistral transform fault or fault zone during the Permian.

Quaternary geologic map of the Havre 1° x 2° quadrangle

USGS Publications Warehouse

Compilations by Fullerton, David S.; Colton, Roger B.; Bush, Charles A.

2012-01-01

The Havre quadrangle encompasses approximately 16,084 km2 (6,210 mi2). The northern boundary is the Montana/Saskatchewan (U.S./Canada) boundary. The quadrangle is in the Northern Plains physiographic province and it includes parts of the Bearpaw Mountains, the Little Rocky Mountains, and the Boundary Plateau. The primary river is the Milk River. The ancestral Missouri River was diverted south of the Bearpaw Mountains by a Laurentide ice sheet. The fill in the buried ancestral valley at and southwest of Havre contains a complex stratigraphy of fluvial, glaciofluvial, ice-contact, glacial, lacustrine, and eolian deposits. The old valley east of Havre now is occupied by the Milk River. The map units are surficial deposits and materials, not landforms. Deposits that comprise some constructional landforms (e.g., ground-moraine deposits, end-moraine deposits, stagnation-moraine deposits, all composed of till) are distinguished for purposes of reconstruction of glacial history. Surficial deposits and materials are assigned to 24 map units on the basis of genesis, age, lithology or composition, texture or particle size, and other physical, chemical, and engineering characteristics. It is not a map of soils that are recognized in engineering geology, or of substrata or parent materials in which pedologic or agronomic soils are formed. Glaciotectonic (ice-thrust) structures and deposits are mapped separately, represented by a symbol. On the glaciated plains and on the Boundary Plateau the surficial deposits are glacial, ice-contact, glaciofluvial, catastrophic flood, alluvial, lacustrine, eolian, and colluvial deposits. In the Bearpaw Mountains and Little Rocky Mountains beyond the limit of Quaternary glaciation they are fluvial, colluvial, and mass-wasting deposits and residual materials. Tills of late Wisconsin and Illinoian ages are represented by map units. Tills of two pre-Illinoian glaciations are not mapped but are widespread in the subsurface and are identified in stratigraphic sections. Thirteen stratigraphic sections document a complex glacial and interglacial history in the quadrangle. Pliocene continental glaciation possibly is represented by erratic blocks of garnet gneiss and pegmatite from the Canadian Shield, perched high on drainage divides in the western Bearpaw Mountains. Glacial striations on bedrock, two boulder trains, and linear ice-molded landforms (primarily drumlins) indicate the possible presence of an east-southeast flowing ice stream in the Havre glacial lobe during late Wisconsin glaciation.

Geodetic Imaging of Glacio-Seismotectonic Processes in Southern Alaska

NASA Astrophysics Data System (ADS)

Sauber, J.; Bruhn, R.; Forster, R.; Hofton, M.

2008-12-01

Across southern Alaska the northwest directed motion of the Pacific plate is accompanied by migration and collision of the Yakutat terrane. The Yakutat terrane is a fragment of the North American plate margin that is partly subducted beneath and partly accreted to the continental margin. Over the last couple of decades the rate of ongoing deformation associated with subduction and a locked main thrust zone has been estimated by geodetic measurements. In the last five years more extensive geodetic measurements, structural and tectonic field studies, thermochronolgy, and high-resolution lidar have been acquired and analyzed as part of the STEEP project [Pavlis et al., 2006]. The nature and magnitude of accretion and translation on upper crustal faults and folds remains uncertain, however, due to complex variations in the style of tectonic deformation, pervasive and changing glaciation, and the logistical challenges of conducting field studies in formidable topography. In this study, we analyze new high-resolution lidar data to extract locations, geometry, and heights of seismogenic faults and zones of active folding across the Malaspina-Seward-Bagley region of the southern Alaska plate boundary that is hypothesized to accommodate upper crustal shortening and right-lateral slip. Airborne Topographic Mapper (ATM) lidar swath data acquired by Krabill et al. in the summer of 2005 and ICESat data (1993-present) cross a number of proposed faults and folds partially masked by glaciation, including the Malaspina thrust, Esker Creek, Chugach-St.Elias thrust, and Contact. Focal mechanisms from this region indicate mostly shallow (0-30 km) thrust and oblique strike-slip faulting. Similarly, rupture in the 1979 St. Elias earthquake (M=7.4) started as a shallow, north-dipping thrust that later changed to more steeply NE dipping with a large right-lateral strike-slip component. Additionally, we are using the morphology and dynamics of glaciers derived from L-Band SAR ice velocities and SAR images to infer the large scale sub-ice structures that form the structural framework of the Seward-Bagley Basins. The new lidar, InSAR, and STEEP results provide constraints that enable us to critically re-evaluate alternate models of the nature of tectonics and structures hidden beneath the ice originally proposed by Ford et al [2003] . Ford, A.L., R.R. Forster, and R.L. Bruhn, 2003, Ice surface velocity patterns on Seward Glacier, Alaska/Yukon, and their implications for regional tectonics in the Saint Elias Mountains, Annals of Glaciology, 36, 21-28.

Minimum work analysis on the critical taper accretionary wedges- insights from analogue modeling

NASA Astrophysics Data System (ADS)

Santimano, Tasca; Rosenau, Matthias; Oncken, Onno

2014-05-01

The Critical taper theory (CTT) is a fundamental concept for the understanding of mountain building processes. Based on force balance it predicts the preferred steady state geometry of an accretionary wedge system and its tectonic regime (extensive, compressive, stable). However, it does not specify which structures are formed and reactivated to reach the preferred state. The latter can be predicted by the minimum work concept. Here we test both concepts and their interplay by analysing two simple sand wedge models which differ only in the thickness of the basal detachment (a layer of glass beads). While the steady state critical taper is controlled by internal and basal friction coefficients and therefore the same in all experiments, different processes can minimise work by 1. reducing gravitational work e.g. by lowering the amount of uplift or volume uplifted, or 2. reducing frictional work e.g. by lowering the load or due to low friction coefficient along thrusts. Since a thick detachment allows entrainment of low friction material and therefore lowering of the friction along active thrusts, we speculate that the style of wedge growth will differ between the two models. We observe that the wedge with a thin basal detachment localizes strain at the toe of the wedge periodically and reactivate older faults to reach the critical topography. On the contrary, in the wedge with the thicker detachment layer, friction along thrusts is lowered due to the entrainment of low friction material from the detachment zone, subsequently increasing the lifetime of a thrust. Long thrust episodes are always followed by a fault of shorter lifetime, with the aim of reaching the critical taper. From the two experiments, we analyze the time-series evolution of the wedge to infer the work done by the two styles of deformation and predict the trend over time to differ but the maximum work to be similar Our observations show that the critical taper theory determines the geometry of the wedge in particular the taper angle. However the path and style of deformation that the wedge adopts i.e. strain partitioning or deformation along one fault, is determined by the energetically lowest pathway. The observation is especially evident in wedges with added complexities or random changes as the wedge matures. This study combines two theories to explain variability in the results of analogue models and perhaps may aid in understanding the complexity in natural wedges. It also delineates that two different mechanics of deformation can lead to the same geometrical wedge or final topography.

Controls on accretion of flysch and melange belts at convergent margins: evidence from the Chugach Bay thrust and Iceworm melange, Chugach accretionary wedge, Alaska

USGS Publications Warehouse

Kusky, Timothy M.; Bradley, Dwight C.; Haeussler, Peter J.; Karl, Susan M.

1997-01-01

Controls on accretion of flysch and melange terranes at convergent margins are poorly understood. Southern Alaska's Chugach terrane forms the outboard accretionary margin of the Wrangellia composite terrane, and consists of two major lithotectonic units, including Triassic-Cretaceous melange of the McHugh Complex and Late Cretaceous flysch of the Valdez Group. The contact between the McHugh Complex and the Valdez Group on the Kenai Peninsula is a tectonic boundary between chaotically deformed melange of argillite, chert, greenstone, and graywacke of the McHugh Complex and a less chaotically deformed melange of argillite and graywacke of the Valdez Group. We assign the latter to a new, informal unit of formational rank, the Iceworm melange, and interpret it as a contractional fault zone (Chugach Bay thrust) along which the Valdez Group was emplaced beneath the McHugh Complex. The McHugh Complex had already been deformed and metamorphosed to prehnite-pumpellyite facies prior to formation of the Iceworm melange. The Chugach Bay thrust formed between 75 and 55 Ma, as shown by Campanian-Maastrichtian depositional ages of the Valdez Group, and fault-related fabrics in the Iceworm melange that are cut by Paleocene dikes. Motion along the Chugach Bay thrust thus followed Middle to Late Cretaceous collision (circa 90-100 Ma) of the Wrangellia composite terrane with North America. Collision related uplift and erosion of mountains in British Columbia formed a submarine fan on the Farallon plate, and we suggest that attempted subduction of this fan dramatically changed the subduction/accretion style within the Chugach accretionary wedge. We propose a model in which subduction of thinly sedimented plates concentrates shear strains in a narrow zone, generating melanges like the McHugh in accretionary complexes. Subduction of thickly sedimented plates allows wider distribution of shear strains to accommodate plate convergence, generating a more coherent accretionary style including the fold-thrust structures that dominate the outcrop pattern in the Valdez belt. Rapid underplating and frontal accretion of the Valdez Group caused a critical taper adjustment of the accretionary wedge, including exhumation of the metamorphosed McHugh Complex, and its emplacement over the Valdez Group. The Iceworm melange formed in a zone of focused fluid flow at the boundary between the McHugh Complex and Valdez Group during this critical taper adjustment of the wedge to these changing boundary conditions.

Controls on accretion of flysch and mélange belts at convergent margins: Evidence from the Chugach Bay thrust and Iceworm mélange, Chugach accretionary wedge, Alaska

NASA Astrophysics Data System (ADS)

Kusky, Timothy M.; Bradley, Dwight C.; Haeussler, Peter J.; Karl, Sue

1997-12-01

Controls on accretion of flysch and mélange terranes at convergent margins are poorly understood. Southern Alaska's Chugach terrane forms the outboard accretionary margin of the Wrangellia composite terrane, and consists of two major lithotectonic units, including Triassic-Cretaceous mélange of the McHugh Complex and Late Cretaceous flysch of the Valdez Group. The contact between the McHugh Complex and the Valdez Group on the Kenai Peninsula is a tectonic boundary between chaotically deformed melange of argillite, chert, greenstone, and graywacke of the McHugh Complex and a less chaotically deformed mélange of argillite and graywacke of the Valdez Group. We assign the latter to a new, informal unit of formational rank, the Iceworm mélange, and interpret it as a contractional fault zone (Chugach Bay thrust) along which the Valdez Group was emplaced beneath the McHugh Complex. The McHugh Complex had already been deformed and metamorphosed to prehnite-pumpellyite facies prior to formation of the Iceworm mélange. The Chugach Bay thrust formed between 75 and 55 Ma, as shown by Campanian-Maastrichtian depositional ages of the Valdez Group, and fault-related fabrics in the Iceworm mélange that are cut by Paleocene dikes. Motion along the Chugach Bay thrust thus followed Middle to Late Cretaceous collision (circa 90-100 Ma) of the Wrangellia composite terrane with North America. Collision related uplift and erosion of mountains in British Columbia formed a submarine fan on the Farallon plate, and we suggest that attempted subduction of this fan dramatically changed the subduction/accretion style within the Chugach accretionary wedge. We propose a model in which subduction of thinly sedimented plates concentrates shear strains in a narrow zone, generating mélanges like the McHugh in accretionary complexes. Subduction of thickly sedimented plates allows wider distribution of shear strains to accommodate plate convergence, generating a more coherent accretionary style including the fold-thrust structures that dominate the outcrop pattern in the Valdez belt. Rapid underplating and frontal accretion of the Valdez Group caused a critical taper adjustment of the accretionary wedge, including exhumation of the metamorphosed McHugh Complex, and its emplacement over the Valdez Group. The Iceworm mélange formed in a zone of focused fluid flow at the boundary between the McHugh Complex and Valdez Group during this critical taper adjustment of the wedge to these changing boundary conditions.

Exhumation History of an Oblique Plate Boundary: Investigating Kaikoura Mountain-building within the Marlborough Fault System, NE South Island New Zealand

NASA Astrophysics Data System (ADS)

Collett, C.; Duvall, A. R.; Flowers, R. M.; Tucker, G. E.

2015-12-01

The Kaikoura Mountains stand high as topographic anomalies in the oblique Pacific-Australian plate boundary zone known as the Marlborough Fault System (MFS), NE South Island New Zealand. The base of both the Inland and Seaward Kaikoura Ranges are bound on the SE by major, steeply NW-dipping, right lateral, active strike-slips (Clarence and Hope faults of the MFS, respectively). Previous geologic mapping, observations of predominantly horizontal fault slip at the surface from GPS and offset Quaternary deposits, and uplift of marine terraces, provide evidence for shortening and mountain-building via distributed deformation off of the main MFS strike-slip faults. However, quantitative estimates of the magnitude and spatial patterns of exhumation and of the timing of mountain-building in the Kaikouras are needed to understand more fully the nature of oblique deformation in the MFS. We present new apatite and zircon (U-Th)/He ages from opposite sides of the Hope and Clarence faults, spanning over 2 km of relief within the Kaikoura Mountains to identify spatial and temporal changes in exhumation rates in relation to the adjacent faults. Young (~3 Ma) apatite He ages and rapid (potentially > 1 mm/yr) exhumation rates from opposite sides of the faults are consistent with previously mentioned evidence of recent, regional, distributed deformation off of the main MFS faults. Moreover, early Miocene zircon He ages imply that parts of this region experienced an earlier phase of fault-related exhumation. Large changes in zircon He ages across the faults from ~20 Ma to > 100 Ma support hypotheses that portions of the Marlborough Faults may be re-activated, early Miocene thrusts. The zircon data are also consistent with the hypothesis of an early Miocene initiation of the oblique Pacific-Australian plate boundary in this region. Evidence for this comes from a change in sedimentation during this time from fine marine sediments to coarse, terrigenous conglomerates. Observing more than one phase of deformation in this active, oblique tectonic setting provides a new quantitative assessment of the evolution of the Pacific-Australian plate boundary in this region and how the accommodation of deformation may change over time.

Up-dip partitioning of displacement components on the oblique-slip Clarence Fault, New Zealand

NASA Astrophysics Data System (ADS)

Nicol, Andrew; Van Dissen, Russell

2002-09-01

Active strike-slip faults in New Zealand occur within an obliquely-convergent plate boundary zone. Although the traces of these faults commonly delineate the base of mountain ranges, they do not always accommodate significant shortening at the free surface. Along the active trace of Clarence Fault in northeastern South Island, New Zealand, displaced landforms and slickenside striations indicate predominantly horizontal displacements at the ground surface, and a right-lateral slip rate of ca. 3.5-5 mm/year during the Holocene. The Inland Kaikoura mountain range occupies the hanging wall of the fault and rises steeply from the active trace to altitudes of ca. 3 km. The geomorphology of the range indicates active uplift and mountain building, which is interpreted to result, in part, from a vertical component of fault slip at depth. These data are consistent with the fault accommodating oblique-slip at depth aligned parallel to the plate-motion vector and compatible with regional geodetic data and earthquake focal-mechanisms. Oblique-slip on the Clarence Fault at depth is partitioned at the free surface into: (1) right-lateral displacement on the fault, and (2) hanging wall uplift produced by distributed displacement on small-scale faults parallel to the main fault. Decoupling of slip components reflects an up-dip transfer of fault throw to an off-fault zone of distributed uplift. Such zones are common in the hanging walls of thrusts and reverse faults, and support the idea that the dip of the oblique-slip Clarence Fault steepens towards the free surface.

The physical behavior and geologic control of radon in mountain streams

USGS Publications Warehouse

Rogers, Allen S.

1956-01-01

Radon measurement were made in several small, turbulent mountain streams in the Wasatch Mountains near Salt Lake City and Ogden, Utah, to determine the relationship between the distribution of radon and its geologic environment. In this area, the distribution of radon in streams can be sued to locate points where relatively large amounts of radon-bearing ground water enter the stream, although other evidence of spring activity may be lacking. These points of influence ground water are marked by abrupt increases (as much as two orders of magnitude within a distance of 50 feet) in the radon content of the stream waters. The excess radon in the stream water is then rapidly lost to the atmosphere through stream turbulence. The rate of radon dissipation is an exponential function, of different slopes, with respect to distance of streamflow, and depend upon the rate and volume of streamflow, and the gradient and nature of the stream channel. The higher radon concentration can be generally related to specific stratigraphic horizons in several different drainage area. Thus, lithologic units which act as the primary aquifers can be identifies. In one area, thrust faults were found to control he influx of ground water into the stream. Estimates, based on radon concentration in stream and related spring waters, can also be made of the major increments of addition of ground water to streamflow where conventional methods such as stream gaging are not practical. The radon in the waters studied was found to be almost completely unsupported by radium in solution.

Thin-skinned tectonics of upper Ojai Valley and Sulfur Mountain vicinity, Ventura basin, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huftile, G.J.

1988-03-01

The Upper Ojai Valley is a tectonic depression between opposing reverse faults. The active, north-dipping San Cayetano fault forms its northern border and has 5.8 km of dip-slip displacement at the Silverthread oil field and 2.6 km of displacement west of Sisar Creek. The fault dies out farther west in Ojai Valley. The southern border is formed by the late Quaternary Sisar-Big-Canyon-Lion fault set, which dips south and merges into a decollement within the south-dipping, ductile Rincon Formation. Folds with north-dipping fold axes, including the Lion Mountain anticline and Reeves syncline, are probably Pliocene. During the late Quaternary, the Sulfurmore » Mountain anticlinorium began forming as a fault-propagation fold, followed closely by the ramping of the south-dipping faults to the surface. One, the Lion fault, cuts the Pleistocene Saugus Formation. To the east, the San Cayetano fault overrides and folds the south-dipping faults. Cross-section balancing shows that the Miocene and younger rocks above the decollement are shortened 6.1 km more than the more competent rocks below. A solution to this bed-length problem is that the decollement becomes a ramp and merges at depth with the steeply south-dipping Oak Ridge fault. This implies that the Sisar, Big Canyon, and Lion faults are frontal thrusts to the Oak Ridge fault. Oil is produced primarily from Mohnian sands and shales north of the Big Canyon fault and from fractured Mohnian shale beneath the Sisar fault.« less

Raising the Gangdese Mountains in southern Tibet

NASA Astrophysics Data System (ADS)

Zhu, Di-Cheng; Wang, Qing; Cawood, Peter A.; Zhao, Zhi-Dan; Mo, Xuan-Xue

2017-01-01

The surface uplift of mountain belts is in large part controlled by the effects of crustal thickening and mantle dynamic processes (e.g., lithospheric delamination or slab breakoff). Understanding the history and driving mechanism of uplift of the southern Tibetan Plateau requires accurate knowledge on crustal thickening over time. Here we determine spatial and temporal variations in crustal thickness using whole-rock La/Yb ratios of intermediate intrusive rocks from the Gangdese arc. Our results show that the crust was likely of normal thickness prior to approximately 70 Ma ( 37 km) but began to thicken locally at approximately 70-60 Ma. The crust reached (58-50) ± 10 km at 55-45 Ma extending over 400 km along the strike of the arc. This thickening was likely due to magmatic underplating as a consequence of rollback and then breakoff of the subducting Neo-Tethyan slab. The crust attained a thickness of 68 ± 12 km at approximately 20-10 Ma, as a consequence of underthrusting of India and associated thrust faulting. The Gangdese Mountains in southern Tibet broadly attained an elevation of >4000 m at approximately 55-45 Ma as a result of isostatic surface uplift driven by crustal thickening and slab breakoff and reached their present-day elevation by 20-10 Ma. Our paleoelevation estimates are consistent not only with the C-O isotope-based paleoaltimetry but also with the carbonate-clumped isotope paleothermometer, exemplifying the promise of reconstructing paleoelevation in time and space for ancient orogens through a combination of magmatic composition and Airy isostatic compensation.

Stratigraphy of lower to middle Paleozoic rocks of northern Nevada and the Antler orogeny

USGS Publications Warehouse

Ketner, Keith B.

2013-01-01

Commonly accepted concepts concerning the lower Paleozoic stratigraphy of northern Nevada are based on the assumption that the deep-water aspects of Ordovician to Devonian siliceous strata are due to their origin in a distant oceanic environment, and their presence where we find them is due to tectonic emplacement by the Roberts Mountains thrust. The concept adopted here is based on the assumption that their deep-water aspects are the result of sea-level rise in the Cambrian, and all of the Paleozoic strata in northern Nevada are indigenous to that area. The lower part of the Cambrian consists mainly of shallow-water cross-bedded sands derived from the craton. The upper part of the Cambrian, and part of the Ordovician, consists mainly of deep-water carbonate clastics carried by turbidity currents from the carbonate shelf in eastern Nevada, newly constructed as a result of sea-level rise. Ordovician to mid-Devonian strata are relatively deep-water siliceous deposits, which are the western facies assemblage. The basal contact of this assemblage on autochthonous Cambrian rocks is exposed in three mountain ranges and is clearly depositional in all three. The western facies assemblage can be divided into distinct stratigraphic units of regional extent. Many stratigraphic details can be explained simply by known changes in sea level. Upper Devonian to Mississippian strata are locally and westerly derived orogenic clastic beds deposited disconformably on the western facies assemblage. This disconformity, clearly exposed in 10 mountain ranges, indicates regional uplift and erosion of the western facies assemblage and absence of local deformation. The disconformity represents the Antler orogeny.

Tectonics, Deep-Seated Structure and Recent Geodynamics of the Caucasus

NASA Astrophysics Data System (ADS)

Amanatashvili, I.; Adamia, Sh.; Lursmanashvili, N.; Sadradze, N.; Meskhia, V.; Koulakov, I.; Zabelina, I.; Jakovlev, A.

2012-04-01

The tectonics and deep-seated structure of the Caucasus are determined by its position between the still converging Eurasian and Africa-Arabian plates, within a wide zone of continental collision. The region in the Late Proterozoic - Early Cenozoic belonged to the Tethys Ocean and its Eurasian and Africa-Arabian margins. During Oligocene-Middle Miocene and Late Miocene-Quaternary time as a result of collision back-arc basins were inverted to form fold-thrust mountain belts and the Transcaucasian intermontane lowlands. The Caucasus is divided into platform and fold-thrust units, and forelands superimposed mainly on the rigid platform zones. The youngest structural units composed of Neogene-Quaternary continental volcanic formations of the Armenian and Javakheti highlands and extinct volcanoes of the Great Caucasus. As a result of detailed geophysical study of the gravity, magnetic, seismic, and thermal fields, the main features of the deep crustal structure of the Caucasus have been determined. Knowledge on the deep lithospheric structure of the Caucasus region is based on surface geology and deep and super deep drilling data combined with gravity, seismic, heat flow, and magnetic investigations. Close correlation between the geology and its deep-seated structures appears in the peculiarities of spatial distribution of gravitational, thermal and magnetic fields, particularly generally expressed in orientation of regional anomalies that is in good agreement with general tectonic structures. In this study we present two tomographic models derived for the region based on two different tomographic approaches. In the first case, we use the travel time data on regional seismicity recorded by networks located in Caucasus. The tomographic inversion is based on the LOTOS code which enables simultaneous determination of P and S velocity distributions and source locations. The obtained model covers the crustal and uppermost mantle depths. The second model, which is constructed for the upper mantle down to 700 km depth, is based on the data from the global ISC catalogue. We use travel times corresponding to rays which travel, at least partly, through the study volume. These data include rays from events in the study area recorded by worldwide stations, as well as teleseismic data recorded at regional stations. The computed seismic models reveal some deep traces of recent tectonic processes in the Caucasus: • For the 5, 15, 25 and 60-km-depth, there appears a clear coincidence between anomalous low velocities of P and S-waves with the fold-thrust mountainous belts of the Great and Lesser Caucasus, and also connection of high-velocity anomalies with the Trasncaucasian forelands. • Lowest-velocity anomalies are characteristic of the areas of Neogene-Quaternary volcanism of the Great and Lesser Caucasus. Areas with the lowest velocities of P- and S-waves coincide with the mountainous-folded belts, whereas the areas of high-velocity predominantly coincide with the platformal structures and forelands, as well as with basins of the Black and Caspian Seas. • Clear spatial correlation of the areas of lowest values of P- and S-velocities with the areas of Neogene-Quaternary volcanism occurs up to the depth of 150-200km that evidences location of magma sources within the crust - upper mantle - asthenosphere. • Tomographic data unambiguously confirm spatial unity of the main structures of the Caucasus and its basement, the location of the structures in situ in Late Cenozoic and connection of the volcanic constructions with their roots - magma chambers.

Mountain building, strike-slip faulting, and landscape evolution in the Marlborough Fault System, NZ: Insights from new low-temperature thermochronology and modeling

NASA Astrophysics Data System (ADS)

Duvall, A. R.; Collett, C.; Flowers, R. M.; Tucker, G. E.; Upton, P.

2016-12-01

The 150 km wide Marlborough Fault System (MFS) and adjacent dextral-reverse Alpine Fault accommodate oblique convergence of the Australian and Pacific plates in a broad transform boundary that extends for much of the South Island New Zealand. Understanding the deformation history of the Marlborough region offers the opportunity to study topographic evolution in a strike-slip setting and a fuller picture of the evolving New Zealand plate boundary as the MFS lies at the transition from oceanic Pacific plate subduction to oblique continental collision. Here we present low-temperature thermochronology from the MFS to place new limits on the timing and style of mountain building. We sampled a range of elevations spanning 2 km within and adjacent to the Kaikoura Mountains, which stand high as topographic anomalies above active strike-slip faults. Young apatite (U-Th)/He ages ( 2-5 Ma) on both sides of range-bounding faults are consistent with regional distributed deformation since the Pliocene initiation of strike-slip faulting. However, large differences in both zircon helium and apatite fission track ages, from Paleogene/Neogene ages within hanging walls to unreset >100 Ma ages in footwalls, indicate an early phase of fault-related vertical exhumation. Thermal modeling using the QTQt program reveals two phases of exhumation within the Kaikoura Ranges: rapid cooling at 15-12 Ma localized to hanging wall rocks and regional rapid cooling reflected in all samples starting at 4-5 Ma. These results and landscape evolution models suggest that, despite the presence of active mountain front faults, much of the topographic relief in this region may predate the onset of strike-slip faulting and that portions of the Marlborough Faults are re-activated thrusts that coincide with the early development of the transpressive plate boundary. Regional exhumation after 5 Ma likely reflects increased proximity to the migrating Pacific plate subduction zone and the buoyant Chatham Rise.

Rock Uplift above the Yakutat Megathrust on Montague Island, Prince William Sound, Alaska

NASA Astrophysics Data System (ADS)

Ferguson, K.; Armstrong, P. A.; Haeussler, P. J.; Arkle, J. C.

2011-12-01

The Yakutat microplate is subducting shallowly (~6°) beneath the North American Plate at a rate of approximately 53 mm/yr to the northwest. Deformation from this flat- slab subduction extends >600 km inland and has resulted in regions of focused rock uplift and exhumation in the Alaska Range, central Chugach Mountains, and St. Elias Mountains. Many questions still remain about how strain is partitioned between these regions of focused uplift, particularly in the Prince William Sound (southern Chugach Mountains) on Montague Island. Montague Island (and adjacent Hinchinbrook Island) are ~20 km above the megathrust where there is a large degree of coupling between the subducting Yakutat microplate and overriding North American Plate. Montague Island is of particular interest because it lies between two areas of rapid rock uplift focused in the St. Elias/eastern Chugach Mountains and the western Chugach Mountains. In the St. Elias/eastern Chugach Mountains, faulting related to collisional processes and bending of fault systems causes rapid rock uplift. About 200 km farther northwest in the western Chugach Mountains, recent rock uplift is caused by underplating along the megathrust that is focused within a syntaxial bend of major fault systems and mountain ranges. Montague Island bounds the southern margin of Prince William Sound, and is steep, narrow, and elongate (81 km long and ~15 km wide). The maximum relief is 914 m, making for very steep, mountainous topography considering the narrow width of the island. During the Mw 9.2 earthquake in 1964, the Patton Bay and Hanning Bay reverse faults were reactivated, with 7 and 5 m of vertical offset, respectively. Both faults dip ~60° NW and strike NE-SW parallel to the long-axis of the island and parallel to geomorphic features including lineaments, elongate valleys, and escarpments. Prominent ~450 m high escarpments are present along the SE-facing side of the island, which suggests rapid and sustained uplift. New apatite (U-Th)/He (AHe) and fission-track (AFT) ages are 1.3 - 1.5 Ma and 4.4 Ma, respectively, at the SW end of Montague Island and AHe ages are 4.4 - 4.6 Ma at the NE end. These age and geomorphic constraints indicate that Montague Island marks a narrow zone of intense deformation probably related to thin-skinned thrust faulting and/or pop-up structures above the megathrust. The youngest AHe ages from Montague Island are similar to those from farther east along the St. Elias - Bagley fault systems implying that the south and east sides of Montague Island, and perhaps the along-trend eastern part of Hinchinbrook Island, may be the westward extension of these fault systems. Additional cooling ages will help constrain the spatial extent of this zone of deformation and potential links with other structural zones caused by Yakutat collision and subduction.

Modeling of wind gap formation and development of sedimentary basins during fold growth: application to the Zagros Fold Belt, Iran.

NASA Astrophysics Data System (ADS)

Collignon, Marine; Yamato, Philippe; Castelltort, Sébastien; Kaus, Boris

2016-04-01

Mountain building and landscape evolution are controlled by the interactions between river dynamics and tectonic forces. Such interactions have been largely studied but a quantitative evaluation of tectonic/geomorphic feedbacks remains required for understanding sediments routing within orogens and fold-and-thrust belts. Here, we employ numerical simulations to assess the conditions of uplift and river incision necessary to deflect an antecedent drainage network during the growth of one or several folds. We propose that a partitioning of the river network into internal (endorheic) and longitudinal drainage arises as a result of lithological differences within the deforming crustal sedimentary cover. We show with examples from the Zagros Fold Belt (ZFB) that drainage patterns can be linked to the incision ratio R between successive lithological layers, corresponding to the ratio between their relative erodibilities or incision coefficients. Transverse drainage networks develop for uplift rates smaller than 0.8 mm.yr-1 and -10 < R < 10. Intermediate drainage network are obtained for uplift rates up to 2 mm.yr-1 and incision ratios of 20. Parallel drainage networks and formation of sedimentary basins occur for large values of incision ratio (R >20) and uplift rates between 1 and 2 mm.yr-1. These results have implications for predicting the distribution of sediment depocenters in fold-and-thrust belts, which can be of direct economic interest for hydrocarbon exploration.

Mercury in Eastern Kentucky coals: Geologic aspects and possible reduction strategies

USGS Publications Warehouse

Hower, J.C.; Eble, C.F.; Quick, J.C.

2005-01-01

Mercury emissions from US coal-fired power plants will be regulated by the US Environmental Protection Agency (USEPA) before the end of the decade. Because of this, the control of Hg in coal is important. Control is fundamentally based on the knowledge of the amounts of Hg in mined, beneficiated, and as-fired coal. Eastern Kentucky coals, on a reserve district level, have Hg contents similar to the USA average for coal at mines. Individual coals show greater variation at the bench scale, with Hg enrichment common in the top bench, often associated with enhanced levels of pyritic sulfur. Some of the variation between parts of eastern Kentucky is also based on the position relative to major faults. The Pine Mountain thrust fault appears to be responsible for elemental enrichment, including Hg, in coals on the footwall side of the thrust. Eastern Kentucky coals shipped to power plants in 1999, the year the USEPA requested coal quality information on coal deliveries, indicate that coals shipped from the region have 0.09 ppm Hg, compared to 0.10 ppm for all delivered coals in the USA. On an equal energy basis, and given equal concentrations of Hg, the high volatile bituminous coals from eastern Kentucky would emit less Hg than lower rank coals from other USA regions. ?? 2005 Elsevier B.V. All rights reserved.

Reinterpretation of the palynology and age of Laramide syntectonic deposits, southwestern Montana, and revision of the Beaverhead Group

NASA Astrophysics Data System (ADS)

Nichols, D. J.; Perry, W. J., Jr.; Haley Johns, J. C.

1985-02-01

New palynological data from syntectonic deposits in southwestern Montana have major temporal implications for Laramide structural relations in the northern Rocky Mountains. Conglomerate and associated sandstones representing the bulk of material eroded from the thrust-faulted margin of the Blacktail-Snowcrest foreland massif are middle Campanian (Aquilapollenites senonicus Interval Zone; estimated absolute age 78 81 Ma). As a major consequence, the foreland buttress responsible for the shape of the southwestern Montana recess of the Cordilleran thrust belt was uplifted and in place by middle Campanian time. Palynomorph assemblages from the Campanian deposits include reworked spores of Paleozoic age that are evidence of provenance. Other less precisely dated syntectonic units in the area differ in age and provenance as well as lithology. Formerly, all these deposits were assigned to the Beaverhead Formation, which is raised to group status herein. The stratigraphic unit shed from the Blacktail-Snowcrest uplift is raised to formation status as the Lima Conglomerate. The term “Beaverhead Group” is restricted to the Lima Conglomerate and to contemporaneous and younger conglomeratic units that differ in lithology and probably in provenance; older sandstone units are removed from the Beaverhead Group. Deposits at the original type section of the Beaverhead Formation are not precisely dated but are no older than Campanian and probably no younger than early Maestrichtian.

The Wallula fault and tectonic framework of south-central Washington, as interpreted from magnetic and gravity anomalies

USGS Publications Warehouse

Blakely, Richard J.; Sherrod, Brian; Weaver, Craig S.; Wells, Ray; Rohay, Alan C.

2014-01-01

The Yakima fold and thrust belt (YFTB) in central Washington has accommodated regional, mostly north-directed, deformation of the Cascadia backarc since prior to emplacement of Miocene flood basalt of the Columbia River Basalt Group (CRBG). The YFTB consists of two structural domains. Northern folds of the YFTB strike eastward and terminate at the western margin of a 20-mGal negative gravity anomaly, the Pasco gravity low, straddling the North American continental margin. Southern folds of the YFTB strike southeastward, form part of the Olympic–Wallowa lineament (OWL), and pass south of the Pasco gravity low as the Wallula fault zone. An upper crustal model based on gravity and magnetic anomalies suggests that the Pasco gravity low is caused in part by an 8-km-deep Tertiary basin, the Pasco sub-basin, abutting the continental margin and concealed beneath CRBG. The Pasco sub-basin is crossed by north-northwest-striking magnetic anomalies caused by dikes of the 8.5 Ma Ice Harbor Member of the CRBG. At their northern end, dikes connect with the eastern terminus of the Saddle Mountains thrust of the YFTB. At their southern end, dikes are disrupted by the Wallula fault zone. The episode of NE–SW extension that promoted Ice Harbor dike injection apparently involved strike-slip displacement on the Saddle Mountains and Wallula faults. The amount of lateral shear on the OWL impacts the level of seismic hazard in the Cascadia region. Ice Harbor dikes, as mapped with aeromagnetic data, are dextrally offset by the Wallula fault zone a total of 6.9 km. Assuming that dike offsets are tectonic in origin, the Wallula fault zone has experienced an average dextral shear of 0.8 mm/y since dike emplacement 8.5 Ma, consistent with right-lateral stream offsets observed at other locations along the OWL. Southeastward, the Wallula fault transfers strain to the north-striking Hite fault, the possible location of the M 5.7 Milton-Freewater earthquake in 1936.

Tonalite and trondhjemite plutonism in the western Chugach Mountains, so. Alaska: an example of near trench magmatism

DOE Office of Scientific and Technical Information (OSTI.GOV)

Monteverde, D.; Pavlis, T.

1985-01-01

In the northern Chugach Mountains of southern Alaska a suite of granitoid plutons were emplaced in a near-trench setting in mid-Early Cretaceous time. The plutons intrude both the then continental edge marked by Jurassic igneous and metamorphic rocks of the Peninsular terrane and the accretionary prism composed of the Early Cretaceous McHugh Complex. Field, petrographic and geochemical data classify the plutonic rocks as ranging from a hornblende-biotite tonalite to a biotite trondjhemite. Most of the rocks are post-metamorphic and show hypidiomorphic granular textures. Locally, however, the rocks are weakly foliated and quartz shows grain size reduction (serrate textures) indicative ofmore » minor ductile strain; suggesting some strain following emplacement. Geochemically, Harker variation diagrams show a linear variation as related to silica content: MgO, FeO total, TiO/sub 2/, and CaO and Al/sub 2/O/sub 3/ decrease while Na/sub 2/O, K/sub 2/O, MnO and P/sub 2/O/sub 5/ maintain constant percentages with increasing silica content. Chemical ranges include: SiO/sub 2/ 61.98 to 74.90%, Al/sub 2/O/sub 3/ 19.35 to 14.25%, CaO 6.93 to 2.23%, Na/sub 2/O averages 4.33%, K/sub 2/O averages 0.91%. The rocks are a high Al/sub 2/O/sub 3/ (calcic.) trondjhemite of Barker (1979). Most of the rocks are strongly peraluminous (>1.1% corundum normative); garnet crystals show equilibrium textures without reaction rims; and stable isotope analysis of a small sample suite show significant /sup 08/O enrichment (>9.6 per mil SMOW). Two possible petrographic models fit the data. The entail a fractional crystallization-assimilation model and a partial melting of a low temperature hydrothermally altered basalt. The tectonic mechanism responsible for this unusual event is elusive but two models are allowable: 1) a ridge-trench encounter; and 2) melting along thrust planes during initiation of subduction - a mechanism analogous to melting along great crystalline thrust sheets.« less

New Geologic Map and Structural Cross Sections of the Death Valley Extended Terrain (southern Sierra Nevada, California to Spring Mountains, Nevada): Toward 3D Kinematic Reconstructions

NASA Astrophysics Data System (ADS)

Lutz, B. M.; Axen, G. J.; Phillips, F. M.

2017-12-01

Tectonic reconstructions for the Death Valley extended terrain (S. Sierra Nevada to Spring Mountains) have evolved to include a growing number of offset markers for strike-slip fault systems but are mainly map view (2D) and do not incorporate a wealth of additional constraints. We present a new 1:300,000 digital geologic map and structural cross sections, which provide a geometric framework for stepwise 3D reconstructions of Late Cenozoic extension and transtension. 3D models will decipher complex relationships between strike-slip, normal, and detachment faults and their role in accommodating large magnitude extension/rigid block rotation. Fault coordination is key to understanding how extensional systems and transform margins evolve with changing boundary conditions. 3D geometric and kinematic analysis adds key strain compatibility unavailable in 2D reconstructions. The stratigraphic framework of Fridrich and Thompson (2011) is applied to rocks outside of Death Valley. Cenozoic basin deposits are grouped into 6 assemblages differentiated by age, provenance, and bounding unconformities, which reflect Pacific-North American plate boundary events. Pre-Cenozoic rocks are grouped for utility: for example, Cararra Formation equivalents are grouped because they form a Cordilleran thrust decollement zone. Offset markers are summarized in the associated tectonic map. Other constraints include fault geometries and slip rates, age, geometry and provenance of Cenozoic basins, gravity, cooling histories of footwalls, and limited seismic/well data. Cross sections were constructed parallel to net-transport directions of fault blocks. Surface fault geometries were compiled from previous mapping and projected to depth using seismic/gravity data. Cooling histories of footwalls guided geometric interpretation of uplifted detachment footwalls. Mesh surfaces will be generated from 2D section lines to create a framework for stepwise 3D reconstruction of extension and transtension in the study area. Analysis of all available data in a seamless 3D framework should force more unique solutions to outstanding kinematic problems, provide a better understanding of the Cordilleran thrust belt, and constrain the mechanisms of strain partitioning between the upper and lower crust.

Giant landslide deposits in northwest Argentina

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fauque, L.; Strecker, M.R.; Bloom, A.L.

1985-01-01

Giant Quaternary landslide deposits occur along mountain fronts in the structural transition zone between the high-angle reverse-fault-bounded Sierras Pampeanas and the low-angle thrust belt of the Sierras Subandinas. There are two modes of occurrence: (1) chaotic masses without distinct geometry, and (2) masses with distinct lobate geometry similar to glacial moraines. Type (1) deposits occur where the moving rock mass followed a narrow valley and blocked the drainage. Many of these caused subsequent formation of lakes and changed the sedimentation processes on pediments at the mountain fronts. In type (2) deposits, lateral and frontal ridges are up to 10 mmore » higher than the interior parts; in some places pressure ridges within the lobes are well preserved. Type (2) deposits show reverse grading and were deposited on relatively smooth pediments or alluvial fans. The lobate geometry strongly suggests that type (2) deposits are a product of flowage and are debris stream or sturzstrom deposits (sense of Heim, 1932 and Hsu, 1975). All investigated deposits occur in areas of demonstrated Quaternary faulting and are interpreted as the result of tectonic movements, although structural inhomogeneities in the source area may have been a significant factor for some of the landslides. No datable materials have yet been found associated with the deposits.« less

Geologic map of the White Hall quadrangle, Frederick County, Virginia, and Berkeley County, West Virginia

USGS Publications Warehouse

Doctor, Daniel H.; Orndorff, Randall C.; Parker, Ronald A.; Weary, David J.; Repetski, John E.

2010-01-01

The White Hall 7.5-minute quadrangle is located within the Valley and Ridge province of northern Virginia and the eastern panhandle of West Virginia. The quadrangle is one of several being mapped to investigate the geologic framework and groundwater resources of Frederick County, Va., as well as other areas in the northern Shenandoah Valley of Virginia and West Virginia. All exposed bedrock outcrops are clastic and carbonate strata of Paleozoic age ranging from Middle Cambrian to Late Devonian. Surficial materials include unconsolidated alluvium, colluvium, and terrace deposits of Quaternary age, and local paleo-terrace deposits possibly of Tertiary age. The quadrangle lies across the northeast plunge of the Great North Mountain anticlinorium and includes several other regional folds. The North Mountain fault zone cuts through the eastern part of the quadrangle; it is a series of thrust faults generally oriented northeast-southwest that separate the Silurian and Devonian clastic rocks from the Cambrian and Ordovician carbonate rocks and shales. Karst development in the quadrangle occurs in all of the carbonate rocks. Springs occur mainly near or on faults. Sinkholes occur within all of the carbonate rock units, especially where the rocks have undergone locally intensified deformation through folding, faulting, or some combination.

The Gibraltar subduction: A decade of new geophysical data

NASA Astrophysics Data System (ADS)

Gutscher, M.-A.; Dominguez, S.; Westbrook, G. K.; Le Roy, P.; Rosas, F.; Duarte, J. C.; Terrinha, P.; Miranda, J. M.; Graindorge, D.; Gailler, A.; Sallares, V.; Bartolome, R.

2012-10-01

The Gibraltar arc, spans a complex portion of the Africa-Eurasia plate boundary marked by slow oblique convergence and intermediate and deep focus seismicity. The seemingly contradictory observations of a young extensional marine basin surrounded by an arcuate fold-and-thrust belt, have led to competing geodynamic models (delamination and subduction). Geophysical data acquired in the past decade provide a test for these models and support a narrow east-dipping, subduction zone. Seismic refraction studies indicate oceanic crust below the western Gulf of Cadiz. Tomography of the upper mantle reveals a steep, east-dipping high P-wave velocity body, beneath Gibraltar. The anisotropic mantle fabric from SKS splitting shows arc-parallel "fast directions", consistent with toroidal flow around a narrow, westward retreating subducting slab. The accompanying WSW advance of the Rif-Betic mountain belt has constructed a thick pile of deformed sediments, an accretionary wedge, characterized by west-vergent thrust anticlines. Bathymetric swath-mapping images an asymmetric embayment at the deformation front where a 2 km high basement ridge has collided. Subduction has slowed significantly since 5 Ma, but deformation of recent sediments and abundant mud volcanoes suggest ongoing activity in the accretionary wedge. Three possible origins for this deformation are discussed; gravitational spreading, overall NW-SE convergence between Africa and Iberia and finally a WSW tectonic push from slow, but ongoing roll-back subduction. In the absence of arc volcanism and shallow dipping thrust type earthquakes, evidence in favor of present-day subduction can only be indirect and remains the object of debate. Continued activity of the subduction offers a possible explanation for great (M > 8.5) earthquakes known to affect the area, like the famous 1755 Great Lisbon earthquake. Recent GPS studies show SW motion of stations in N Morocco at velocities of 3-6 mm/yr indicating the presence of an independent block, a "Rif-Betic-Alboran" microplate, situated between Iberia and Africa.

3D Reconstruction of geological structures based on remote sensing data: example from Anaran anticline, Lurestan province, Zagros folds and thrust belt, Iran.

NASA Astrophysics Data System (ADS)

Snidero, M.; Amilibia, A.; Gratacos, O.; Muñoz, J. A.

2009-04-01

This work presents a methodological workflow for the 3D reconstruction of geological surfaces at regional scale, based on remote sensing data and geological maps. This workflow has been tested on the reconstruction of the Anaran anticline, located in the Zagros Fold and Thrust belt mountain front. The used remote sensing data-set is a combination of Aster and Spot images as well as a high resolution digital elevation model. A consistent spatial positioning of the complete data-set in a 3D environment is necessary to obtain satisfactory results during the reconstruction. The Aster images have been processed by the Optimum Index Factor (OIF) technique, in order to facilitate the geological mapping. By pansharpening of the resulting Aster image with the SPOT panchromatic one we obtain the final high-resolution image used during the 3D mapping. Structural data (dip data) has been acquired through the analysis of the 3D mapped geological traces. Structural analysis of the resulting data-set allows us to divide the structure in different cylindrical domains. Related plunge lines orientation has been used to project data along the structure, covering areas with little or no information. Once a satisfactory dataset has been acquired, we reconstruct a selected horizon following the dip-domain concept. By manual editing, the obtained surfaces have been adjusted to the mapped geological limits as well as to the modeled faults. With the implementation of the Discrete Smooth Interpolation (DSI) algorithm, the final surfaces have been reconstructed along the anticline. Up to date the results demonstrate that the proposed methodology is a powerful tool for 3D reconstruction of geological surfaces when working with remote sensing data, in very inaccessible areas (eg. Iran, China, Africa). It is especially useful in semiarid regions where the structure strongly controls the topography. The reconstructed surfaces clearly show the geometry in the different sectors of the structure: presence of a back thrust affecting the back limb in the southern part of the anticline, the geometry of the grabens located along the anticline crest, the crosscutting relationship in the north-south faulted zone with the main thrust, the northern dome periclinal closure.

Applications of Morphochronology to the Active Tectonics of Tibet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ryerson, F J; Tapponnier, P; Finkel, R C

2005-01-28

The Himalayas and the Tibetan Plateau were formed as a result of the collision of India and Asia, and provide an excellent opportunity to study the mechanical response of the continental lithosphere to tectonic stress. Geophysicists are divided in their views on the nature of this response advocating either (1) homogeneously distributed deformation with the lithosphere deforming as a fluid continuum or (2) deformation is highly localized with the lithosphere that deforms as a system of blocks. The resolution of this issue has broad implications for understanding the tectonic response of continental lithosphere in general. Homogeneous deformation is supported bymore » relatively low decadal, geodetic slip-rate estimates for the Altyn Tagh and Karakorum Faults. Localized deformation is supported by high millennial, geomorphic slip-rates constrained by both cosmogenic and radiocarbon dating on these faults. Based upon the agreement of rates determined by radiocarbon and cosmogenic dating, the overall linearity of offset versus age correlations, and on the plateau-wide correlation of landscape evolution and climate history, the disparity between geomorphic and geodetic slip-rate determinations is unlikely to be due to the effects of surface erosion on the cosmogenic age determinations. Similarly, based upon the consistency of slip-rates over various observation intervals, secular variations in slip-rate appear to persist no longer than 2000 years and are unlikely to provide reconciliation. Conversely, geodetic and geomorphic slip-rate estimates on the Kunlun fault, which does not have significant splays or associated thrust faults, are in good agreement, indicating that there is no fundamental reason why these complementary geodetic and geomorphic methods should disagree. Similarly, the geodetic and geomorphic estimates of shortening rates across the northeastern edge of the plateau are in reasonable agreement, and the geomorphic rates on individual thrust faults demonstrate a significant eastward decrease in the shortening rate. This rate decrease is consistent with the transfer of slip from the Altyn Tagh Fault (ATF) to genetically-related thrust mountain building at its terminus. Rates on the ATF suggest a similar decrease in rate, but the current data set is too small to be definitive. Overall, the high, late Pleistocene-Holocene, geomorphic slip velocities on the major strike-slip faults of Tibet, suggests that they absorb as much of India's convergence relative to Siberia as the Himalayan Main Frontal Thrust on the southern edge of the plateau.« less

Corrective Action Investigation Plan for Corrective Action Unit 99: Rainier Mesa/Shoshone Mountain, Nevada Test Site, Nevada with Errata and ROTC 1, Rev. No. 0

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCord, John; Marutzky, Sam

2004-12-01

This Corrective Action Investigation Plan (CAIP) was developed for Corrective Action Unit (CAU) 99, Rainier Mesa/Shoshone Mountain. The CAIP is a requirement of the ''Federal Facility Agreement and Consent Order'' (FFACO) agreed to by the State of Nevada, the U.S. Department of Energy (DOE), and the U.S. Department of Defense (DoD) (FFACO, 1996). The FFACO addresses environmental restoration activities at U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO) facilities and sites including the underground testing area(s) of the Nevada Test Site (NTS). This CAIP describes the investigation activities currently planned for the Rainier Mesa/Shoshone Mountain CAU.more » These activities are consistent with the current Underground Test Area (UGTA) Project strategy described in Section 3.0 of Appendix VI, Revision No. 1 (December 7, 2000) of the FFACO (1996) and summarized in Section 2.1.2 of this plan. The Rainier Mesa/Shoshone Mountain CAU extends over several areas of the NTS (Figure 1-1) and includes former underground nuclear testing locations in Areas 12 and 16. The area referred to as ''Rainier Mesa'' includes the geographical area of Rainier Mesa proper and the contiguous Aqueduct Mesa. Figure 1-2 shows the locations of the tests (within tunnel complexes) conducted at Rainier Mesa. Shoshone Mountain is located approximately 20 kilometers (km) south of Rainier Mesa, but is included within the same CAU due to similarities in their geologic setting and in the nature and types of nuclear tests conducted. Figure 1-3 shows the locations of the tests conducted at Shoshone Mountain. The Rainier Mesa/Shoshone Mountain CAU falls within the larger-scale Rainier Mesa/Shoshone Mountain Investigation Area, which also includes the northwest section of the Yucca Flat CAU as shown in Figure 1-1. Rainier Mesa and Shoshone Mountain lie adjacent to the Timber Mountain Caldera Complex and are composed of volcanic rocks that erupted from the caldera as well as from more distant sources. This has resulted in a layered volcanic stratigraphy composed of thick deposits of welded and nonwelded ash-flow tuff and lava flows. These deposits are proximal to the source caldera and are interstratified with the more distal facies of fallout tephra and bedded reworked tuff from more distant sources. In each area, a similar volcanic sequence was deposited upon Paleozoic carbonate and siliciclastic rocks that are disrupted by various thrust faults, normal faults, and strike-slip faults. In both Rainier Mesa (km) to the southwest, and Tippipah Spring, 4 km to the north, and the tunnel complex is dry. Particle-tracking simulations performed during the value of information analysis (VOIA) (SNJV, 2004b) indicate that most of the regional groundwater that underlies the test locations at Rainier Mesa and Shoshone Mountain eventually follows similar and parallel paths and ultimately discharges in Death Valley and the Amargosa Desert. Particle-tracking simulations conducted for the regional groundwater flow and risk assessment indicated that contamination from Rainier Mesa and Shoshone Mountain were unlikely to leave the NTS during the 1,000-year period of interest (DOE/NV, 1997a). It is anticipated that CAU-scale modeling will modify these results somewhat, but it is not expected to radically alter the outcome of these previous particle-tracking simulations within the 1,000-year period of interest. The Rainier Mesa/Shoshone Mountain CAIP describes the corrective action investigation (CAI) to be conducted at the Rainier Mesa/Shoshone Mountain CAU to evaluate the extent of contamination in groundwater due to the underground nuclear testing. The CAI will be conducted by the UGTA Project, which is part of the NNSA/NSO Environmental Restoration Project (ERP). The purpose and scope of the CAI are presented in this section, followed by a summary of the entire document.« less

Earthquake in Hindu Kush Region, Afghanistan

NASA Image and Video Library

2015-10-27

On Oct. 26, 2015, NASA Terra spacecraft acquired this image of northeastern Afghanistan where a magnitude 7.5 earthquake struck the Hindu Kush region. The earthquake's epicenter was at a depth of 130 miles (210 kilometers), on a probable shallowly dipping thrust fault. At this location, the Indian subcontinent moves northward and collides with Eurasia, subducting under the Asian continent, and raising the highest mountains in the world. This type of earthquake is common in the area: a similar earthquake occurred 13 years ago about 12 miles (20 kilometers) away. This perspective image from the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) instrument on NASA's Terra spacecraft, looking southwest, shows the hypocenter with a star. The image was acquired July 8, 2015, and is located near 36.4 degrees north, 70.7 degrees east. http://photojournal.jpl.nasa.gov/catalog/PIA20035

Transient Deformation Patterns in Response to Quaternary Glacial Advance-Retreat Across the Offshore St. Elias Mountains, southern Alaska

NASA Astrophysics Data System (ADS)

Worthington, L. L.; Clary, W. A.; Daigle, H.; Koons, P. O.; Gulick, S. P. S.; Jaeger, J. M.

2016-12-01

The southern Alaska margin, home to the St. Elias Mountains, the highest coastal mountain range on Earth experiencing the highest erosion rates on Earth, provides a superb setting for evaluating competing influences of rheological and climate control on orogen development. Previous studies have recognized this potential, but conclusions were limited due to the absence of information on the time-dependent behavior of climate and rheological processes. These limitations can now be surpassed due to 1) the recent availability of high-precision age constraints on the structural and stratigraphic evolution of offshore sediments and structures and 2) geotechnical information on the extent of dewatering and related spatial changes in the material properties of these sediments. We correlate emerging results from Integrated Ocean Drilling Program (IODP) Expedition 341 Sites U1420 and U1421 with regional seismic data across the continental shelf and slope to determine the spatial and temporal evolution of thrusting in response to Yakutat-North American convergence. Our mapping shows that the pattern of faulting changed from distributed across the shelf to highly localized away from the primary glacial depocenter over the course of one glacial cycle. Core samples suggest that the glacially derived sediment is overpressured, with pore pressures possibly reaching >90% of lithostatic stress. Elevated pore pressures develop rapidly in response to focused glaciomarine sedimentation, in addition to direct ice loading, and may induce a transient state of wedge reorganization manifested as a change in localization of deformation. This relationship suggests that the additive response of pore pressure variations over glacial cycles throughout the Pleistocene and Holocene result in constant reorganization of deformation style and location.

Exhumation of the Deylaman fault trend and its effects on the deformation style of the western Alborz belt in Iran

NASA Astrophysics Data System (ADS)

Hakimi Asiabar, Saeid; Bagheriyan, Siyamak

2018-03-01

The Alborz range in northern Iran stretches along the southern coast of the Caspian Sea and finally runs northeast and merges into the Pamir mountains in Afghanistan. Alborz mountain belt is a doubly vergent orogen formed along the northern edge of the Iranian plateau in response to the closure of the Neo-Tethys ocean and continental collision between Arabia and Eurasia. The south Caspian depression—the Alborz basin of Mesozoic age (with W-E trend) in northern Iran—inverted in response to the Arabia-Eurasia collision. Pre-existing extensional faults of the south Caspian-Alborz system preferentially reactivated as contractional faults because of tectonic inversion. These contractional structures tend to run parallel to the trends of pre-existing extensional faults and acquire W and WNW-ESE orientations across the previous accommodation zones that were imposed by the reactivation of adjacent extensional faults with different directions. The NNE to N dipping faults show evidences of reactivation. The Deylaman fault is one of the important faults of western Alborz in Iran and is an example of inversion tectonic style of deformation in the western Alborz mountain range. The Deylaman fault, with an E-W trend, contains three discontinuous fault segments in the area under investigation. These fault segments have evidence of oblique right-lateral reverse motion and links eastward to the dextral Kandavan thrust. The importance of this fault is due to its effect on sedimentation of several rock units from the Jurassic to Neogene in western Alborz; the rock facies on each side of this fault are very different and illustrate different parts of tectonic history.

A geologic framework for mineralization in the western Brooks Range

USGS Publications Warehouse

Young, Lorne E.

2004-01-01

The Brooks Range is a 950-km-long north-vergent fold and thrust belt, which was formed during Mesozoic convergence of the continental Arctic Alaska terrane and the oceanic Angayucham terrane and was further shortened and uplifted in Tertiary time. The Arctic Alaska terrane consists of parautochthonous rocks and the Endicott Mountains and De Long Mountains subterranes. The Endicott Mountains allochthon of the western Brooks Range is the setting for many sulfide and barite occurrences, such as the supergiant Red Dog zinc-lead mine. Mineralization is sediment hosted and most commonly is present in black shale and carbonate turbidites of the Mississippian Kuna Formation. The reconstructed Kuna basin is a 200 by +600 km feature that represents the culmination of a remarkable chain of events that includes three fluvial-deltaic and two or more orogenic cycles, Middle Devonian to Mississippian episodes of extension and igneous activity, and the emergence of a seaward Lower Proterozoic landmass that may have constituted a barrier to marine circulation. Mississippian extension and related horst-and-graben architecture in the western Brooks Range is manifested in part by strong facies variability between coeval units of allochthons and structural plates. Shallow marine to possibly nonmarine arkose, platform to shelf carbonate, slope-to-basin shale, chert and carbonate turbidites, and submarine volcanic rocks are all represented in Mississippian time. The structural setting of Mississippian sedimentation, volcanism, and mineralization in the Kuna basin may be comparable to documented Devono-Mississippian extensional sags or half-grabens in the subsurface north of the Brooks Range. Climate, terrestrial ecosystems, multiple fluvial-deltaic aquifers, and structural architecture affected the liberation, movement, and redeposition of metals in ways that are incompletely understood.

Oak Ridge fault, Ventura fold belt, and the Sisar decollement, Ventura basin, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yeats, R.S.; Huftile, G.J.; Grigsby, F.B.

1988-12-01

The rootless Ventura Avenue, San Miguelito, and Rincon anticlines (Ventura fold belt) in Pliocene -Pleistocene turbidites are fault-propagation folds related to south-dipping reverse faults rising from a decollement in Miocene shale. To the east, the Sulfur Mountain anticlinorium overlies and is cut by the Sisar, Big Canyon, and Lion south-dipping thrusts that merge downward into the Sisar decollement in lower Miocene shale. Shortening of the Miocene and younger sequence is {approximately} 3 km greater than that of underlying competent Paleogens strata in the Ventura fold belt and {approximately} 7 km greater farther east at Sulfur Mountain. Cross-section balancing requires thatmore » this difference be taken up by the Paleogene sequence at the Oak Ridge fault to the south. Convergence is northeast to north-northeast on the base of earthquake focal mechanisms, borehole breakouts, and piercing-point offest of the South Mountain seaknoll by the Oak Ridge fault. A northeast-trending line connecting the west end of Oak Ridge and the east end of Sisar fault separates an eastern domain where late Quaternary displacement is taken up entirely on the Oak Ridge fault and a western domain where displacement is transferred to the Sisar decollement and its overlying rootless folds. This implies that (1) the Oak Ridge fault near the coast presents as much seismic risk as it does farther east, despite negligible near-surface late Quaternary movement; (2) ground-rupture hazard is high for the Sisar fault set in the upper Ojai Valley; and (3) the decollement itself could produce an earthquake analogous to the 1987 Whittier Narrows event in Low Angeles.« less

Ridge of Jagged Peaks on Titan

NASA Image and Video Library

2016-07-29

This synthetic-aperture radar image was obtained by NASA's Cassini spacecraft during its T-120 pass over Titan's southern latitudes on June 7, 2016. The area shown here measures about 40 by 60 miles (70 by 100 kilometers) and is centered at about 60 degrees south latitude, 130 degrees west longitude. Radar illuminates the scene from the left at a 28-degree incidence angle. At the center of the image is a bright feature oriented from upper left to lower right. This is interpreted to be a long ridge with jagged peaks, likely created by methane rainfall erosion. Some of the individual peaks rise about 2,400 feet (800 meters) above the valley floor. The ridge has a considerably gentler slope on its left side (which appears brighter here) than on its right. Frequently, mountains shaped like this on Earth are fractured blocks of the planet's crust, thrusted upward and then tilted, creating a shallow slope on one side and a steeper slope on the fractured, faulted edge. Also presented here is an annotated version of the image, along with a radar image of the Dragoon Mountains in Arizona just east of Tucson. The Dragoon feature represents a tilted fault block, formed by spreading that has occurred across the western U.S., and has a similar shape to that of the Titan ridge. The Dragoon radar image was produced using data from NASA's Shuttle Radar Topography Mission (credit: NASA/JPL-Caltech/NGA). Radar illuminates the scene from the left in that image as well. Titan has displayed many features that are strikingly similar to Earth: lakes, seas, rivers, dunes and mountains. Scientists think it possible that, like Earth, the giant moon's crust has experienced familiar processes of uplift and spreading, followed by erosion. http://photojournal.jpl.nasa.gov/catalog/PIA20709

Depositional settings, correlation, and age carboniferous rocks in the western Brooks Range, Alaska

USGS Publications Warehouse

Dumoulin, Julie A.; Harris, Anita G.; Blome, Charles D.; Young, Lorne E.

2004-01-01

The Kuna Formation (Lisburne Group) in northwest Alaska hosts the Red Dog and other Zn-Pb-Ag massive sulfide deposits in the Red Dog district. New studies of the sedimentology and paleontology of the Lisburne Group constrain the setting, age, and thermal history of these deposits. In the western and west-central Brooks Range, the Lisburne Group includes both deep- and shallow-water sedimentary facies and local volcanic rocks that are exposed in a series of thrust sheets or allochthons. Deep-water facies in the Red Dog area (i.e., the Kuna Formation and related rocks) are found chiefly in the Endicott Mountains and structurally higher Picnic Creek allochthons. In the Red Dog plate of the Endicott Mountains allochthon, the Kuna consists of at least 122 m of thinly interbedded calcareous shale, calcareous spiculite, and bioclastic supportstone (Kivalina unit) overlain by 30 to 240 m of siliceous shale, mudstone, calcareous radiolarite, and calcareous lithic turbidite (Ikalukrok unit). The Ikalukrok unit in the Red Dog plate hosts all massive sulfide deposits in the area. It is notably carbonaceous, is generally finely laminated, and contains siliceous sponge spicules and radiolarians. The Kuna Formation in the Key Creek plate of the Endicott Mountains allochthon (60–110 m) resembles the Ikalukrok unit but is unmineralized and has thinner carbonate layers that are mainly organic-rich dolostone. Correlative strata in the Picnic Creek allochthon include less shale and mudstone and more carbonate (mostly calcareous spiculite). Conodonts and radiolarians indicate an age range of Osagean to early Chesterian (late Early to Late Mississippian) for the Kuna in the Red Dog area. Sedimentologic, faunal, and geochemical data imply that most of the Kuna formed in slope and basin settings characterized by anoxic or dysoxic bottom water and by local high productivity.

Rheological Properties and Heterogeneities Along the Down-Dip Extent of a Subduction Megathrust: Insights from the Condrey Mountain Schist, Northern California

NASA Astrophysics Data System (ADS)

Tewksbury-Christle, C. M.; Behr, W. M.; Helper, M. A.

2017-12-01

Episodic tremor and slow slip (ETS) is commonly observed in warm subduction zones down-dip of a locked megathrust. Proposed mechanisms for ETS involve some form of rheological heterogeneity along the subduction interface. Observations from exhumed subduction-related rocks allow us to investigate the constitutive laws that govern the interface, as well as the types and distributions of rheological heterogeneities that develop and/or persist in the tremor source region. The Late Jurassic to Early Cretaceous Condrey Mountain Schist (CMS), Klamath Mountains, northern California, provides insight into interface rheology along the down-dip extent (350-450°C, 5-8 kbar) of a subduction megathrust. The CMS consists of greenschist and blueschist facies metasediments (including graphitic mica schists), metabasalts, and metaserpentinites, all pervasively deformed under prograde metamorphic conditions with minimal retrogressive overprint. A transect of peak metamorphic temperatures determined using graphite crystallinity shows a constant, but small, inverted thermal gradient with increasing structural depth, suggesting equilibration of temperature discontinuities during underplating. Despite the lack of thermal contrasts, rheological heterogeneities are preserved in the form of km-scale cryptic thrusts that separate lithological packages deforming by different mechanisms. Graphitic mica schists exhibit pervasive cleavage-microlithon fabrics indicative of deformation by quartz dissolution-precipitation creep. Blueschist-facies oceanic crustal sequences juxtaposed against the graphitic mica schists show coeval deformation, but are deformed primarily by dislocation creep in amphibole. These observations suggest that the subduction megathrust likely transitions down-dip into a viscous (rather than frictional) interface shear zone, but that original lithological heterogeneities persist in the form of non-Newtonian vs. Newtonian viscous patches.

Tabletop Tectonics: Diverse Mountain Ranges Using Flour and Graphite

NASA Astrophysics Data System (ADS)

Davis, D. M.

2006-12-01

It has been recognized for some time that the frontal deformation zones where plates converge (foreland fold- and-thrust belts on continents and accretionary wedges at subduction zones) involve shortening over a decoupling layer, or decollement. A simple but successful way of explaining many aspects of their behavior is called the critical Coulomb wedge model, which regards these contractional wedges as analogous to the wedge-shaped mass of soil accreted in front of a bulldozer, or the wedge of snow that piles up in front of a snow plow. The shape and deformation history of the accreted wedge of soil or snow will depend upon the frictional strength of the material being plowed up and the surface over which it is being plowed. The same is true of `bulldozer' wedges consisting of many km thick piles of sediment at convergent plate margins. Using flour (or powdered milk), sandpaper, graphite, transparency sheets, and athletic field marker chalk, manipulated with sieves, brushes, pastry bags and blocks and sheets of wood, it is possible to demonstrate a wide variety of processes and tectonic styles observed at convergent plate boundaries. Model fold-and-thrust belts that behave like natural examples with a decollement that is strong (e.g., in rock without high pore fluid pressure) or weak (e.g., in a salt horizon or with elevated pore fluid pressure) can be generated simply by placing wither sandpaper or graphite beneath the flour that is pushed across the tabletop using a block of wood (the strong basement and hiterland rocks behind the fold-thrust belt). Depending upon the strength of the decollement, the cross-sectional taper of the deforming wedge will be thin or broad, the internal deformation mild or intense, and the structures either close to symmetric or strongly forward-vergent, just as at the analogous natural fold-thrust belts. Including a horizontal sheet of wood or Plexiglas in front of the pushing block allows generation of an accretionary wedge, outer-are high, and forearc basin, just as over a subduction zone. Any dark material emplaced (a pastry bag works well) atop the experiment before deformation in the form of football-field `hash marks' every 10 cm allows for easy calculation of strain distribution at any time during or after the experiment. Finally, the entire orogen can be excavated using a plastic photocopier transparency sheet. If the original set-up included occasional thin layers of red and blue field marker chalk within sedimentary column (the rest of which consists of white flour or powdered milk), excavation reveals (quite colorfully) many internal details of the fold-thrust belts that have been generated.

Mars Structural and Stratigraphic Mapping along the Coprates Rise

NASA Technical Reports Server (NTRS)

Saunders, R Stephen

2009-01-01

This geologic mapping project supports a topical study of structures in east Thaumasia associated with the Coprates rise. The study examines cuesta-like features on the east flank of the Coprates rise first identified by Saunders et al. [1]. Mapping combines detailed local stratigraphy, structural geology and topography. Hogbacks and cuestas indicate erosion of tilted rock units. The extent of the erosion will be determined in the course of the mapping. The region of interest lies along the eastern margin of Thaumasia bounded by latitudes -15 and -35 and longitudes 50 to 70 W (Figure 1). Three MTM geologic quadrangles are being compiled for publication by the USGS (-20057, -25057, -30057). All existing data sources are used including THEMIS, MOC, CTX, HiRISE, MOLA and gravity, as well as higher level data available through the PDS data nodes at ASU, UA and Washington University. The extremely valuable ASU JMARS tools are used for analysis of many of the data sets. ArcGIS software has been obtained and is being learned for the map compilation.

Fluid-rock interaction at the northern Hunter Mountain contact aureole, CA, USA

NASA Astrophysics Data System (ADS)

Skora, S.; Baumgartner, L.

2003-04-01

One of the world largest wollastonite deposits is located at the northern end of the Hunter Mountain Batholith, Death Valley National Park (CA, USA). The exposed Palaeozoic continental shelf sediments consist of sandy dolomites and limestones, often interbedded with chert nodules and quartzitic layers. The wollastonite was formed in the quartz-rich zones within the Mississippian Tin Mountain Limestone and the Devonian Lost Burro Formation. The sediment sequence was folded and thrusted towards the SE during the Permian/Triassic Sonoma orogeny. The folds were partly reactivated and rotated during the intrusion. A large, km-scale, anticline/syncline pair was folded and rotated from its the regional N-S trend into an E-W trend during intrusion of the Hunter Mountain Batholith and its satellite. Contact metamorphism resulted in the formation of tremolite, forsterite, and periclase in the siliceous dolomites. Tremolite, diopside and wollastonite were produced in quartz-dolomite-bearing limestones. Evidence for fluid flow is found in the intrusion and the host rocks. The periclase zone in dolomites next to the intrusion documents infiltration of a water-rich, probably magmatic, fluid. The X{CO_2} content was < 0.07 at temperatures of 640 - 700^oC. Furthermore, bodies of wollastonite ore occur well within the tremolite zone, in the northern part of a anticline. This demonstrates channelized infiltration of water-rich fluids (X{CO_2} < 0.03) and the capture of fluids in fold hinges. δD-values of 60-90 ppm (SMOW) of tremolites are consistent with the presence of magmatic water. Sets of irregularly spaced (0,2 - 2m), parallel, sub-horizontal fractures next to the wollastonite ore document fluid circulation in the cooling intrusion. Alteration zones (2-5cm) surround these fractures. Here, the kfs+cpx+pl+qtz+bt+hbl+mag igneous assemblage is changed to scp+hbl+cal+ab+ti±ep. Ti-rich, oscillatory zoned garnets partially fill these fractures. This relatively high temperature alteration documents the circulation of NaCl - CaCO_3 rich fluids. A convective fluid flow system was present in the northern Hunter Mountain contact aureole. At least some wollastonite formation was determined by water-rich, probably magmatic, fluid infiltration. Therefore, structures played an important role in providing fluid pathways. For the high temperature alteration zones in the intrusion, it is most likley that the fluids were derived from the surrounding sediments.

Middle to late Cenozoic basin evolution in the western Alborz Mountains: Implications for the onset of collisional deformation in northern Iran

NASA Astrophysics Data System (ADS)

Guest, Bernard; Horton, Brian K.; Axen, Gary J.; Hassanzadeh, Jamshid; McIntosh, William C.

2007-12-01

Oligocene-Miocene strata preserved in synclinal outcrop belts of the western Alborz Mountains record the onset of Arabia-Eurasia collision-related deformation in northern Iran. Two stratigraphic intervals, informally named the Gand Ab and Narijan units, represent a former basin system that existed in the Alborz. The Gand Ab unit is composed of marine lagoonal mudstones, fluvial and alluvial-fan clastic rocks, fossiliferous Rupelian to Burdigalian marine carbonates, and basalt flows yielding 40Ar/39Ar ages of 32.7 ± 0.3 and 32.9 ± 0.2 Ma. The Gand Ab unit is correlated with the Oligocene-lower Miocene Qom Formation of central Iran and is considered a product of thermal subsidence following Eocene extension. The Narijan unit unconformably overlies the Gand Ab unit and is composed of fluvial-lacustrine and alluvial fan sediments exhibiting contractional growth strata. We correlate the Narijan unit with the middle to upper Miocene Upper Red Formation of central Iran on the basis of lithofacies similarities, stratigraphic position, and an 8.74 ± 0.15 Ma microdiorite dike (40Ar/39Ar) that intruded the basal strata. Deformation timing is constrained by crosscutting relationships and independent thermochronological data. The Parachan thrust system along the eastern edge of the ancestral Taleghan-Alamut basin is cut by dikes dated at 8.74 ± 0.15 Ma to 6.68 ± 0.07 Ma (40Ar/39Ar). Subhorizontal gravels that unconformably overlie tightly folded and faulted Narijan strata are capped by 2.86 ± 0.83 Ma (40Ar/39Ar) andesitic lava flows. These relationships suggest that Alborz deformation had migrated southward into the Taleghan-Alamut basin by late Miocene time and shifted to its present location along the active range front by late Pliocene time. Data presented here demonstrate that shortening in the western Alborz Mountains had started by late middle Miocene time. This estimate is consistent with recent thermochronological results that place the onset of rapid exhumation in the western Alborz at ˜12 Ma. Moreover, nearly synchronous Miocene contraction in the Alborz, Zagros Mountains, Turkish-Iranian plateau, and Anatolia suggests that the Arabia-Eurasia collision affected a large region simultaneously, without a systematic outward progression of mountain building away from the collision zone.

Distinguishing thrust sequences in gravity-driven fold and thrust belts

NASA Astrophysics Data System (ADS)

Alsop, G. I.; Weinberger, R.; Marco, S.

2018-04-01

Piggyback or foreland-propagating thrust sequences, where younger thrusts develop in the footwalls of existing thrusts, are generally assumed to be the typical order of thrust development in most orogenic settings. However, overstep or 'break-back' sequences, where later thrusts develop above and in the hangingwalls of earlier thrusts, may potentially form during cessation of movement in gravity-driven mass transport deposits (MTDs). In this study, we provide a detailed outcrop-based analysis of such an overstep thrust sequence developed in an MTD in the southern Dead Sea Basin. Evidence that may be used to discriminate overstep thrusting from piggyback thrust sequences within the gravity-driven fold and thrust belt includes upright folds and forethrusts that are cut by younger overlying thrusts. Backthrusts form ideal markers that are also clearly offset and cut by overlying younger forethrusts. Portions of the basal detachment to the thrust system are folded and locally imbricated in footwall synclines below forethrust ramps, and these geometries also support an overstep sequence. However, new 'short-cut' basal detachments develop below these synclines, indicating that movement continued on the basal detachment rather than it being abandoned as in classic overstep sequences. Further evidence for 'synchronous thrusting', where movement on more than one thrust occurs at the same time, is provided by displacement patterns on sequences of thrust ramp imbricates that systematically increases downslope towards the toe of the MTD. Older thrusts that initiate downslope in the broadly overstep sequence continue to move and therefore accrue greater displacements during synchronous thrusting. Our study provides a template to help distinguish different thrust sequences in both orogenic settings and gravity-driven surficial systems, with displacement patterns potentially being imaged in seismic sections across offshore MTDs.

Along-strike structural variation and thermokinematic development of the Cenozoic Bitlis-Zagros fold-thrust belt, Turkey and Iraqi Kurdistan

NASA Astrophysics Data System (ADS)

Barber, Douglas E.; Stockli, Daniel F.; Koshnaw, Renas I.; Tamar-Agha, Mazin Y.; Yilmaz, Ismail O.

2016-04-01

The Bitlis-Zagros orogen in northern Iraq is a principal element of the Arabia-Eurasia continent collision and is characterized by the lateral intersection of two structural domains: the NW-SE trending Zagros proper system of Iran and the E-W trending Bitlis fold-thrust belt of Turkey and Syria. While these components in northern Iraq share a similar stratigraphic framework, they exhibit along-strike variations in the width and style of tectonic zones, fold morphology and trends, and structural inheritance. However, the distinctions of the Bitlis and Zagros segments remains poorly understood in terms of timing and deformation kinematics as well as first-order controls on fold-thrust development. Structural and stratigraphic study and seismic data combined with low-T thermochronometry provide the basis for reconstructions of the Bitlis-Zagros fold-thrust belt in southeastern Turkey and northern Iraq to elucidate the kinematic and temporal relationship of these two systems. Balanced cross-sections were constructed and incrementally restored to quantify the deformational evolution and use as input for thermokinematic models (FETKIN) to generate thermochronometric ages along the topographic surface of each cross-section line. The forward modeled thermochronometric ages from were then compared to new and previously published apatite and zircon (U-Th)/He and fission-track ages from southeastern Turkey and northern Iraq to test the validity of the timing, rate, and fault-motion geometry associated with each reconstruction. The results of these balanced theromokinematic restorations integrated with constraints from syn-tectonic sedimentation suggest that the Zagros belt between Erbil and Suleimaniyah was affected by an initial phase of Late Cretaceous exhumation related to the Proto-Zagros collision. During the main Zagros phase, deformation advanced rapidly and in-sequence from the Main Zagros Fault to the thin-skinned frontal thrusts (Kirkuk, Shakal, Qamar) from middle to latest Miocene times, followed by out-of-sequence development of the Mountain Front Flexure (Qaradagh anticline) by ~5 Ma. In contrast, initial exhumation in the northern Bitlis belt occurred by mid-Eocene time, followed by collisional deformation that propagated southward into northern Iraqi Kurdistan during the middle to late Miocene. Plio-Pleistocene deformation was partitioned into out-of-sequence reactivation of the Ora thrust along the Iraq-Turkey border, concurrent with development of the Sinjar and Abdulaziz inversion structures at the edge of the Bitlis deformation front. Overall, these data suggest the Bitlis and Zagros trends evolved relatively independently during Cretaceous and early Cenozoic times, resulting in very different structural and stratigraphic inheritance, before being affected contemporaneously by major phase of in-sequence shortening during middle to latest Miocene and out-of-sequence deformation since the Pliocene. Limited seismic sections corroborate the notion that the structural style and trend of the Bitlis fold belt is dominated by inverted Mesozoic extensional faults, whereas the Zagros structures are interpreted mostly as fault-propagation folds above a Triassic décollement. These pre-existing heterogeneities in the Bitlis contributed to the lower shortening estimates, variable anticline orientation, and irregular fold spacing and the fundamentally different orientations of the Zagros-Bitlis belt in Iraqi Kurdistan and Turkey.

A geologic history of the north-central Appalachians, part 3. The Alleghany orogeny

USGS Publications Warehouse

Faill, R.T.

1998-01-01

The north-central Appalachians occupy a critical position within the 3000+ km-long Appalachian orogen, lying southwest of the boundary between the central and northern Appalachians (CNAB). The one-billion-year-long history of tectonic activity in eastern Laurentia includes the creation and evolution of the Appalachian orogen during the Paleozoic and the Mesozoic transformation of the orogen into a passive margin during Pangea's disassembly. A most important ingredient in the evolution of the orogen was the Alleghany orogeny, which was driven by the convergence and collision between Laurentia (Laurussia) and West Gondwana (Africa). The Alleghany orogeny in the central and southern Appalachians was a de??collement tectonism that involved a larger part of eastern Laurentia than had the previous three orogenies. The fundamental element was a very low-angle thrust (de??collement) that originated in mid-crustal levels east of the presently-exposed Appalachians and rose westwardly to progressively higher levels in the upper crust and the supra-crustal Paleozoic section. Alleghany deformation was widely developed in the hanging-wall block (allochthon), primarily in the form of thrust faults and fold-and-thrust structures, both of which splayed upward from the basal de??collement. The youngest manifestations of the Alleghany orogeny were northeast-trending strike-slip faults and dextral shear zones in the Piedmont. In the north-central Appalachians, the exposed allochthon consists of two parts: the sedimentary externides (Appalachian Plateau and Valley and Ridge provinces) and the crystalline externides (Reading Prong, Blue Ridge belt, and Piedmont province). Long, thrust-cored anticlines predominate in the sedimentary externides. A widespread layer-parallel shortening preceded the folding; it is largely coaxial with the folding but extends considerably farther to the northwest toward the craton. It is hypothesized that the folding developed in reverse order, sequentially from the northwest to the southeast The crystalline externides are dominated by low-angle thrust faults and upright folds trending east-northeast The first-order Valley and Ridge folds on the northwest side acted as a buttress and diverted the crystalline externides rocks north-northwestwardly, onto the topographic low area over the Anthracite region. This thrusting of the crystalline externides caused anthracitization of the coals within the Pennsylvanian rocks there. Metamorphism and magmatism were significant events during the earlier phase of the Alleghany orogeny in the southern Appalachians. Whatever magmatism and medium-to high-grade metamorphism developed in the north-central Appalachians are in the covered internides to the southeast. The Alleghany orogeny of the north-central Appalachians occurred during the Early Permian. Erosion of anticlinal crests probably began as the folds grew, with accumulation of this locally-derived sediment in the intervening synclines. A regional alluvial plain coalesced above the partially-eroded externides structures as erosion of the pre-Alleghany highland and the Alleghany hinterland mountains continued to the southeast, spreading sediment to the northwest. This erosion and northwest transport probably persisted, with diminishing intensity, throughout the remainder of the Permian and into the Mesozoic, and changed only with the beginning of crustal extension during the Late Triassic.

Evaluation of various thrust calculation techniques on an F404 engine

NASA Technical Reports Server (NTRS)

Ray, Ronald J.

1990-01-01

In support of performance testing of the X-29A aircraft at the NASA-Ames, various thrust calculation techniques were developed and evaluated for use on the F404-GE-400 engine. The engine was thrust calibrated at NASA-Lewis. Results from these tests were used to correct the manufacturer's in-flight thrust program to more accurately calculate thrust for the specific test engine. Data from these tests were also used to develop an independent, simplified thrust calculation technique for real-time thrust calculation. Comparisons were also made to thrust values predicted by the engine specification model. Results indicate uninstalled gross thrust accuracies on the order of 1 to 4 percent for the various in-flight thrust methods. The various thrust calculations are described and their usage, uncertainty, and measured accuracies are explained. In addition, the advantages of a real-time thrust algorithm for flight test use and the importance of an accurate thrust calculation to the aircraft performance analysis are described. Finally, actual data obtained from flight test are presented.

Age and evolution of thin-skinned deformation in Zacatecas, Mexico: Sevier orogeny evidence in the Mexican Fold-Thrust Belt

NASA Astrophysics Data System (ADS)

Ramírez-Peña, César Francisco; Chávez-Cabello, Gabriel

2017-07-01

Integrating U-Pb ages from zircons of syn- and postectonic intrusives emplaced in folded pre- and synorogenic marine sedimentary rocks, it is proposed that thin-skinned deformation in the Concepción del Oro salient of the Mexican Fold Thrust Belt in northern Zacatecas, Mexico, was active between 92 and 71.6 Ma. The intrusives Pico de Teyra and El Peñuelo (U-Pb zircon ages: 76.9 and 72.5 Ma) show internal tectonic foliations and horizontal shear zones that cut off aplitic veins, which apparently developed syntectonically to thin-skinned deformation. Other intrusives like Saltillito (71.6 Ma) and Concepción del Oro are clearly postectonic because they are undeformed internally, cut regional structures and are younger than syntectonic plutons. Biostratigraphic ages reported for synorogenic sediments (Concepción del Oro and Parras formations) indicate that regional thin-skinned deformation was active between Early Turonian and Late Campanian, which is in agreement with syn and postectonic intrusive emplacement ages in the area. Nevertheless, the thin-skinned structures are disrupted by a younger NNW-SSE high angle reverse and normal faults that uplifts the San Julián Block in the west and truncate the Concepción del Oro salient, suggesting a post-Paleocene thick-skinned stage of deformation. In this work, we propose that style and age of thin-skinned deformation is similar to the Sevier orogeny in the Rocky Mountains.

The continuation of the Kazerun fault system across the Sanandaj-Sirjan zone (Iran)

NASA Astrophysics Data System (ADS)

Safaei, Homayon

2009-08-01

The Kazerun (or Kazerun-Qatar) fault system is a north-trending dextral strike-slip fault zone in the Zagros mountain belt of Iran. It probably originated as a structure in the Panafrican basement. This fault system played an important role in the sedimentation and deformation of the Phanerozoic cover sequence and is still seismically active. No previous studies have reported the continuation of this important and ancient fault system northward across the Sanandaj-Sirjan zone. The Isfahan fault system is a north-trending dextral strike-slip fault across the Sanandaj-Sirjan zone that passes west of Isfahan city and is here recognized for the first time. This important fault system is about 220 km long and is seismically active in the basement as well as the sedimentary cover sequence. This fault system terminates to the south near the Main Zagros Thrust and to the north at the southern boundary of the Urumieh-Dokhtar zone. The Isfahan fault system is the boundary between the northern and southern parts of Sanandaj-Sirjan zone, which have fundamentally different stratigraphy, petrology, geomorphology, and geodynamic histories. Similarities in the orientations, kinematics, and geologic histories of the Isfahan and Kazerun faults and the way they affect the magnetic basement suggest that they are related. In fact, the Isfahan fault is a continuation of the Kazerun fault across the Sanandaj-Sirjan zone that has been offset by about 50 km of dextral strike-slip displacement along the Main Zagros Thrust.

The Neoacadian orogenic core of the souther Appalachians: a Geo-traverse through the migmatitic inner Piedmont from the Brushy Mountains to Lincolnton, North Carolina

USGS Publications Warehouse

Merschat, Arthur J.; Hatcher, Robert D.; Byars, Heather E.; Gilliam, William G.; Eppes, Martha Cary; Bartholomew, Mervin J.

2012-01-01

The Inner Piedmont extends from North Carolina to Alabama and comprises the Neoacadian (360–345 Ma) orogenic core of the southern Appalachian orogen. Bordered to west by the Blue Ridge and the exotic Carolina superterrane to the east, the Inner Piedmont is cored by an extensive region of migmatitic, sillimanite-grade rocks. It is a composite of the peri-Laurentian Tugaloo terrane and mixed Laurentian and peri-Gondwanan affinity Cat Square terrane, which are exposed in several gentle-dipping thrust sheets (nappes). The Cat Square terrane consists of Late Silurian to Early Devonian pelitic schist and metagraywacke intruded by several Devonian to Mississippian peraluminous granitoids, and juxtaposed against the Tugaloo terrane by the Brindle Creek fault. This field trip through the North Carolina Inner Piedmont will examine the lithostratigraphies of the Tugaloo and Cat Square terranes, deformation associated with Brindle Creek fault, Devonian-Mississippian granitoids and charnockite of the Cat Square terrane, pervasive amphibolite-grade Devonian-Mississippian (Neoacadian) deformation and metamorphism throughout the Inner Piedmont, and existence of large crystalline thrust sheets in the Inner Piedmont. Consistent with field observations, geochronology and other data, we have hypothesized that the Carolina superterrane collided obliquely with Laurentia near the Pennsylvania embayment during the Devonian, overrode the Cat Square terrane and Laurentian margin, and squeezed the Inner Piedmont out to the west and southwest as an orogenic channel buttressed against the footwall of the Brevard fault zone.

Insights upon upper crustal arhitecture of a subduction zone and its surroundings - Vrancea Zone and Focsani Basin - substantiated by geophysical studies

NASA Astrophysics Data System (ADS)

Bocin, A.; Stephenson, R.; Mocanu, V.

2007-12-01

The DACIA PLAN (Danube and Carpathian Integrated Action on Processes in the Lithosphere and Neotectonics) deep seismic reflection survey was performed in August-September 2001, with the proposed objective of obtaining new information on the deep structure of the external Carpathians nappes and the architecture of Tertiary/Quaternary basin developed within and adjacent to the Vrancea zone, including the rapidly subsiding Focsani Basin. The DACIA-PLAN profile is about 140 km long, having a roughly NW-SE direction, from near the southeast Transylvanian Basin, across the mountainous southeastern Carpathians and their foreland to near the Danube River. A high resolution 2.5D velocity model of the upper crust along the seismic profile has been determined from a tomographic inversion and a 2D ray tracing forward modelling of the DACIA PLAN first arrival data. Peculiar shallow high velocities indicate that pre-Tertiary basement in the Vrancea Zone (characterised by velocities greater than 5.6 km/s) is involved in Carpathian thrusting while rapid alternance, vertically or horizontally, of velocity together with narrowingly contemporary crustal events suggests uplifting. Further to the east, at the foreland basin-thrust belt transition zone (well defined within velocity values), the velocity model suggests a nose of the Miocene Subcarpathians nappe being underlain by Focsani Basin units. A Miocene and younger Focsani Basin sedimentary succession of ~10 km thickness is ascertained by a gradual increase of velocities and strongly defined velocity boundaries.

Role of tectonic inheritance in the instauration of Tunisian Atlassic fold-and-thrust belt: Case of Bouhedma - Boudouaou structures

NASA Astrophysics Data System (ADS)

Ghanmi, Mohamed Abdelhamid; Ghanmi, Mohamed; Aridhi, Sabri; Ben Salem, Mohamed Sadok; Zargouni, Fouad

2016-07-01

Tectonic inversion in the Bouhedma-Boudouaou Mountains was investigated through recent field work and seismic lines interpretation calibrated with petroleum well data. Located to the Central-Southern Atlas of Tunisia, this area signed shortened intra-continental fold-and-thrust belts. Two dissymmetric anticlines characterize Bouhedma - Boudouaou major fold. These structures show a strong virgation respectively from E-W to NNE-SSW as a response to the interference between both tectonic inversion and tectonic inheritance. This complex geometry is driven by Mesozoic rifting, which marked an extensional inherited regime. A set of late Triassic-Early Jurassic E-W and NW-SE normal faults dipping respectively to the North and to the East seems to widely affect the overall geodynamic evolution of this domain. They result in major thickness changes across the hanging wall and the footwall blocks in response with the rifting activity. Tectonic inversion is inferred from convergence between African and European plates since late Cretaceous. During Serravalian - Tortonian event, NW-SE trending paroxysm led to: 1) folding of pre-inversion and syn-inversion strata, 2) reactivation of pre-existing normal faults to reverse ones and 3) orogeny of the main structures with NE-SW and E-W trending. The compressional feature still remains active during Quaternary event (Post-Villafranchian) with N-S trending compression. Contraction during inversion generates folding and internal deformation as well as Fault-Propagation-Fold and folding related strike.

Static Performance of Six Innovative Thrust Reverser Concepts for Subsonic Transport Applications: Summary of the NASA Langley Innovative Thrust Reverser Test Program

NASA Technical Reports Server (NTRS)

Asbury, Scott C.; Yetter, Jeffrey A.

2000-01-01

The NASA Langley Configuration Aerodynamics Branch has conducted an experimental investigation to study the static performance of innovative thrust reverser concepts applicable to high-bypass-ratio turbofan engines. Testing was conducted on a conventional separate-flow exhaust system configuration, a conventional cascade thrust reverser configuration, and six innovative thrust reverser configurations. The innovative thrust reverser configurations consisted of a cascade thrust reverser with porous fan-duct blocker, a blockerless thrust reverser, two core-mounted target thrust reversers, a multi-door crocodile thrust reverser, and a wing-mounted thrust reverser. Each of the innovative thrust reverser concepts offer potential weight savings and/or design simplifications over a conventional cascade thrust reverser design. Testing was conducted in the Jet-Exit Test Facility at NASA Langley Research Center using a 7.9%-scale exhaust system model with a fan-to-core bypass ratio of approximately 9.0. All tests were conducted with no external flow and cold, high-pressure air was used to simulate core and fan exhaust flows. Results show that the innovative thrust reverser concepts achieved thrust reverser performance levels which, when taking into account the potential for system simplification and reduced weight, may make them competitive with, or potentially more cost effective than current state-of-the-art thrust reverser systems.

Active geodynamics of the Caucasus/Caspian region educed from GPS, and seismic Observations

NASA Astrophysics Data System (ADS)

Gadirov (Kadirov), Fakhraddin; Floyd, Michael; Reilinger, Robert; Alizadeh, Akif; Guliyev, Ibrahim; Mammadov, Samir; Safarov, Rafig

2017-04-01

The geodynamic and earthquake activity in the Caucasus/Caspian region is due to the ongoing collision of the Arabian plate with Eurasia. The Caucasus and Caspian Sea are historically among the most seismically active regions on earth. These earthquakes have caused thousands of deaths and great economic distress. Future earthquakes in the Caucasus and Caspian Sea must be considered and planned for in order to limit their impact on the people, ecology, and infrastructure of the region. Within this plate tectonics context, we examine deformation of the Caucasus region and show that most crustal shortening in the collision zone is accommodated by the Greater Caucasus Fold-and-Thrust Belt (GCFTB) along the southern edge of the Greater Caucasus Mountains. The eastern GCFTB appears to bifurcate west of Baku, with one branch following the accurate geometry of the Greater Caucasus, turning towards the south and traversing the Neftchala Peninsula. A second branch may extend directly into the Caspian Sea south of Baku, likely connecting to the Central Caspian Seismic Zone. We model deformation in terms of a locked thrust fault that coincides in general with the main surface trace of the GCFTB. We consider two end-member models, each of which tests the likelihood of one or other of the branches being the dominant cause of observed deformation. Our models indicate that strain is actively accumulating on the fault along the 200 km segment of the fault west of Baku (approximately between longitudes 47-49°E). Parts of this segment of the fault broke in major earthquakes historically (1191, 1859, 1902) suggesting that significant future earthquakes (M 6-7) are likely on the central and western segment of the fault. We observe a similar deformation pattern across the eastern end of the GCFTB along a profile crossing the Kura Depression and Greater Caucasus Mountains in the vicinity of Baku. Along this eastern segment, a branch of the fault changes from a NW-SE striking thrust to an N-S oriented strike-slip fault. The similar deformation pattern along the eastern and central GCFTB segments raises the possibility that major earthquakes may also occur in eastern Azerbaijan. However, the eastern segment of the GCFTB has no record of large historic earthquakes, and is characterized by thick, highly saturated and over-pressured sediments within the Kura Depression and adjacent Caspian Basin that may inhibit elastic strain accumulation in favour of fault creep, and/or distributed faulting and folding. Thus, while our analyses suggest that large earthquakes are likely in central and western Azerbaijan, it is still uncertain whether significant earthquakes are also likely along the eastern segment, and on which structure. Ongoing and future focused studies of active deformation promise to shed further light on the tectonics and earthquake hazards in this highly populated and developed part of Azerbaijan.

A transect through the base of the Bronson Hill Terrane in western New Hampshire

USGS Publications Warehouse

Walsh, Gregory J.; Valley, Peter M.; Sicard, Karri R.; Thompson, Thelma Barton; Thompson, Peter J.

2012-01-01

This trip will present the preliminary results of ongoing bedrock mapping in the North Hartland and Claremont North 7.5-minute quadrangles in western New Hampshire. The trip will travel from the Lebanon pluton to just north of the Sugar River pluton (Fig. 1) with the aim of examining the lower structural levels of the Bronson Hill anticlinorium (BHA), and the nature of the boundary with the rocks of the Connecticut Valley trough (CVT). Spear and others (2002, 2003, 2008) proposed that western New Hampshire was characterized by five major faults bounding five structural levels including, from lowest to highest, the “chicken yard line”, Western New Hampshire Boundary Thrust, Skitchewaug nappe, Fall Mountain nappe, and Chesham Pond nappe. Lyons and others (1996, 1997) showed the lowest level cored by the Cornish nappe and floored by the Monroe fault. Thompson and others (1968) explained the geometry of units by folding without major thrust faults, and described the second level as the Skitchewaug nappe. This trip will focus on the two lowest levels which we have revised to call the Monroe and Skitchewaug Mountain thrust sheets. Despite decades of geologic mapping in the northeastern United States at various scales, little 1:24,000-scale (or larger scale) modern bedrock mapping has been published for the state of New Hampshire. In fact, of the New England states, New Hampshire contains the fewest published, modern bedrock geologic maps. Conversely, adjacent Vermont has a relatively high percentage of modern bedrock maps due to focused efforts to create a new state-wide bedrock geologic map over the last few decades. The new Vermont map (Ratcliffe and others, 2011) has identified considerable gaps in our knowledge of the bedrock geology in adjacent New Hampshire where published maps are, in places, more than 50 years old and at scales ranging from 1:62,500 to 1:250,000. Fundamental questions remain concerning the geology across the Connecticut River, especially in regards to the stratigraphy of the BHA and CVT, and the distribution, or even existence, of faults ranging in age from Devonian to Mesozoic (e.g., Spear and others, 2008; McWilliams and others, 2010; Walsh and others, 2010). Questions to ponder on this trip include, but are not limited to: 1) Is the Bronson Hill anticlinorium allochthonous? 2) What is the crust beneath the Bronson Hill anticlinorium? 3) Is there a “Big Staurolite nappe” as proposed by Spear and others (2002, 2003, 2008)? 4) What is the role of Taconic, Acadian, and Alleghanian orogenesis in the tectonic development of the region? Modern 1:24,000-scale mapping is the first step towards answering these questions. Mapping will be supplemented by modern geochronology and geochemistry as this project develops. We plan to share some of our provisional results during this field trip.

Visualizing along-strike change in deformation style using analog modeling and digital visualization software

NASA Astrophysics Data System (ADS)

Burberry, C. M.

2012-12-01

It is a well-known phenomenon that deformation style varies in space; both along the strike of a deformed belt and along the strike of individual structures within that belt. This variation in deformation style is traditionally visualized with a series of closely spaced 2D cross-sections. However, the use of 2D section lines implies plane strain along those lines, and the true 3D nature of the deformation is not necessarily captured. By using a combination of remotely sensed data, analog modeling of field datasets and this remote data, and numerical and digital visualization of the finished model, a 3D understanding and restoration of the deformation style within the region can be achieved. The workflow used for this study begins by considering the variation in deformation style which can be observed from satellite images and combining this data with traditional field data, in order to understand the deformation in the region under consideration. The conceptual model developed at this stage is then modeled using a sand and silicone modeling system, where the kinematics and dynamics of the deformation processes can be examined. A series of closely-spaced cross-sections, as well as 3D images of the deformation, are created from the analog model, and input into a digital visualization and modeling system for restoration. In this fashion, a valid 3D model is created where the internal structure of the deformed system can be visualized and mined for information. The region used in the study is the Sawtooth Range, Montana. The region forms part of the Montana Disturbed Belt in the Front Ranges of the Rocky Mountains, along strike from the Alberta Syncline in the Canadian Rocky Mountains. Interpretation of satellite data indicates that the deformation front structures include both folds and thrust structures. The thrust structures vary from hinterland-verging triangle zones to foreland-verging imbricate thrusts along strike, and the folds also vary in geometry along strike. The analog models, constrained by data from exploration wells, indicate that this change in geometry is related to a change in mechanical stratigraphy along the strike of the belt. Results from the kinematic and dynamic analysis of the digital model will also be presented. Additional implications of such a workflow and visualization system include the possibility of creating and viewing multiple cross-sections, including sections created at oblique angles to the original model. This allows the analysis of the non-plane strain component of the models and thus a more complete analysis, understanding and visualization of the deformed region. This workflow and visualization system is applicable to any region where traditional field methods must be coupled with remote data, intensely processed depth data, or analog modeling systems in order to generate valid geologic or geophsyical models.

Principal facts for gravity stations and physical property measurements in the Lake Mead 30' by 60' quadrangle, Nevada and Arizona

USGS Publications Warehouse

Langenheim, V.E.; Davidson, J.G.; Anderson, M.L.; Blank, H.R.

1999-01-01

The U.S. Geological Survey (USGS) collected 811 gravity stations on the Lake Mead 30' by 60' quadrangle from October, 1997 to September, 1999. These data were collected in support of geologic mapping of the Lake Mead quadrangle. In addition to these new data, gravity stations were compiled from a number of sources. These stations were reprocessed according to the reduction method described below and used for the new data. Density and magnetic susceptibility measurements were also performed on more than 250 rock samples. The Lake Mead quadrangle ranges from 360 to 360 30' north latitude and from 114° to 115° west longitude. It spans most of Lake Mead (see index map, below), the largest manmade lake in the United States, and includes most of the Lake Mead National Recreation Area. Its geology is very complex; Mesozoic thrust faults are exposed in the Muddy Mountains, Precambrian crystalline basement rocks are exhumed in tilted fault blocks near Gold Butte, extensive Tertiary volcanism is evident in the Black Mountains, and strike-slip faults of the right-lateral Las Vegas Valley shear zone and the left-lateral Lake Mead fault system meet near the Gale Hills. These gravity data and physical property measurements will aid in the 3-dimensional characterization of structure and stratigraphy in the quadrangle as part of the Las Vegas Urban Corridor mapping project.

The interplay of fold mechanisms and basement weaknesses at the transition between Laramide basement-involved arches, north-central Wyoming, USA

NASA Astrophysics Data System (ADS)

Neely, Thomas G.; Erslev, Eric A.

2009-09-01

Horizontally-shortened, basement-involved foreland orogens commonly exhibit anastomosing networks of bifurcating basement highs (here called arches) whose structural culminations are linked by complex transition zones of diversely-oriented faults and folds. The 3D geometry and kinematics of the southern Beartooth arch transition zone of north-central Wyoming were studied to understand the fold mechanisms and control on basement-involved arches. Data from 1581 slickensided minor faults are consistent with a single regional shortening direction of 065°. Evidence for oblique-slip, vertical axis rotations and stress refraction at anomalously-oriented folds suggests formation over reactivated pre-existing weaknesses. Restorable cross-sections and 3D surfaces, constrained by surface, well, and seismic data, document blind, ENE-directed basement thrusting and associated thin-skinned backthrusting and folding along the Beartooth and Oregon Basin fault systems. Between these systems, the basement-cored Rattlesnake Mountain backthrust followed basement weaknesses and rotated a basement chip toward the basin before the ENE-directed Line Creek fault system broke through and connected the Beartooth and Oregon Basin fault systems. Slip was transferred at the terminations of the Rattlesnake Mountain fault block by pivoting to the north and tear faulting to the south. In summary, unidirectional Laramide compression and pre-existing basement weaknesses combined with fault-propagation and rotational fault-bend folding to create an irregular yet continuous basement arch transition.

A 10 nN resolution thrust-stand for micro-propulsion devices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chakraborty, Subha; Courtney, Daniel G.; Shea, Herbert, E-mail: herbert.shea@epfl.ch

We report on the development of a nano-Newton thrust-stand that can measure up to 100 μN thrust from different types of microthrusters with 10 nN resolution. The compact thrust-stand measures the impingement force of the particles emitted from a microthruster onto a suspended plate of size 45 mm × 45 mm and with a natural frequency over 50 Hz. Using a homodyne (lock-in) readout provides strong immunity to facility vibrations, which historically has been a major challenge for nano-Newton thrust-stands. A cold-gas thruster generating up to 50 μN thrust in air was first used to validate the thrust-stand. Better thanmore » 10 nN resolution and a minimum detectable thrust of 10 nN were achieved. Thrust from a miniature electrospray propulsion system generating up to 3 μN of thrust was measured with our thrust-stand in vacuum, and the thrust was compared with that computed from beam diagnostics, obtaining agreement within 50 nN to 150 nN. The 10 nN resolution obtained from this thrust-stand matches that from state-of-the-art nano-Newton thrust-stands, which measure thrust directly from the thruster by mounting it on a moving arm (but whose natural frequency is well below 1 Hz). The thrust-stand is the first of its kind to demonstrate less than 3 μN resolution by measuring the impingement force, making it capable of measuring thrust from different types of microthrusters, with the potential of easy upscaling for thrust measurement at much higher levels, simply by replacing the force sensor with other force sensors.« less

Dielectric Barrier Discharge (DBD) Plasma Actuators Thrust-Measurement Methodology Incorporating New Anti-Thrust Hypothesis

NASA Technical Reports Server (NTRS)

Ashpis, David E.; Laun, Matthew C.

2014-01-01

We discuss thrust measurements of Dielectric Barrier Discharge (DBD) plasma actuators devices used for aerodynamic active flow control. After a review of our experience with conventional thrust measurement and significant non-repeatability of the results, we devised a suspended actuator test setup, and now present a methodology of thrust measurements with decreased uncertainty. The methodology consists of frequency scans at constant voltages. The procedure consists of increasing the frequency in a step-wise fashion from several Hz to the maximum frequency of several kHz, followed by frequency decrease back down to the start frequency of several Hz. This sequence is performed first at the highest voltage of interest, then repeated at lower voltages. The data in the descending frequency direction is more consistent and selected for reporting. Sample results show strong dependence of thrust on humidity which also affects the consistency and fluctuations of the measurements. We also observed negative values of thrust or "anti-thrust", at low frequencies between 4 Hz and up to 64 Hz. The anti-thrust is proportional to the mean-squared voltage and is frequency independent. Departures from the parabolic anti-thrust curve are correlated with appearance of visible plasma discharges. We propose the anti-thrust hypothesis. It states that the measured thrust is a sum of plasma thrust and anti-thrust, and assumes that the anti-thrust exists at all frequencies and voltages. The anti-thrust depends on actuator geometry and materials and on the test installation. It enables the separation of the plasma thrust from the measured total thrust. This approach enables more meaningful comparisons between actuators at different installations and laboratories. The dependence on test installation was validated by surrounding the actuator with a large diameter, grounded, metal sleeve.

A 10 nN resolution thrust-stand for micro-propulsion devices

NASA Astrophysics Data System (ADS)

Chakraborty, Subha; Courtney, Daniel G.; Shea, Herbert

2015-11-01

We report on the development of a nano-Newton thrust-stand that can measure up to 100 μN thrust from different types of microthrusters with 10 nN resolution. The compact thrust-stand measures the impingement force of the particles emitted from a microthruster onto a suspended plate of size 45 mm × 45 mm and with a natural frequency over 50 Hz. Using a homodyne (lock-in) readout provides strong immunity to facility vibrations, which historically has been a major challenge for nano-Newton thrust-stands. A cold-gas thruster generating up to 50 μN thrust in air was first used to validate the thrust-stand. Better than 10 nN resolution and a minimum detectable thrust of 10 nN were achieved. Thrust from a miniature electrospray propulsion system generating up to 3 μN of thrust was measured with our thrust-stand in vacuum, and the thrust was compared with that computed from beam diagnostics, obtaining agreement within 50 nN to 150 nN. The 10 nN resolution obtained from this thrust-stand matches that from state-of-the-art nano-Newton thrust-stands, which measure thrust directly from the thruster by mounting it on a moving arm (but whose natural frequency is well below 1 Hz). The thrust-stand is the first of its kind to demonstrate less than 3 μN resolution by measuring the impingement force, making it capable of measuring thrust from different types of microthrusters, with the potential of easy upscaling for thrust measurement at much higher levels, simply by replacing the force sensor with other force sensors.

Characterization of the hydrologic resources of San Miguel County, New Mexico, and identification of hydrologic data gaps, 2011

USGS Publications Warehouse

Matherne, Anne Marie; Stewart, Anne M.

2012-01-01

The U.S. Geological Survey (USGS), in cooperation with San Miguel County, New Mexico, conducted a study to assess publicly available information regarding the hydrologic resources of San Miguel County and to identify data gaps in that information and hydrologic information that could aid in the management of available water resources. The USGS operates four continuous annual streamgages in San Miguel County. Monthly discharge at these streamgages is generally bimodally distributed, with most runoff corresponding to spring runoff and to summer monsoonal rains. Data compiled since 1951 on the geology and groundwater resources of San Miguel County are generally consistent with the original characterization of depth and availability of groundwater resources and of source aquifers. Subsequent exploratory drilling identified deep available groundwater in some locations. Most current (2011) development of groundwater resources is in western San Miguel County, particularly in the vicinity of El Creston hogback, the hogback ridge just west of Las Vegas, where USGS groundwater-monitoring wells indicate that groundwater levels are declining. Regarding future studies to address identified data gaps, the ability to evaluate and quantify surface-water resources, both as runoff and as potential groundwater recharge, could be enhanced by expanding the network of streamgages and groundwater-monitoring wells throughout the county. A series of seepage surveys along the lengths of the rivers could help to determine locations of surface-water losses to and gains from the local groundwater system and could help to quantify the component of streamflow attributable to irrigation return flow; associated synoptic water-quality sampling could help to identify potential effects to water quality attributable to irrigation return flow. Effects of groundwater withdrawals on streamflow could be assessed by constructing monitoring wells along transects between production wells and stream reaches of interest to monitor decline or recovery of the water table, to quantify the timing and extent of water-table response, and to identify the spatial extent of capture zones. Assessment of groundwater potential could be aided by a county-wide distribution of water-level information and by a series of maps of groundwater potential, compiled for each individual aquifer, including saline aquifers, for which the potential for municipal use through desalination could be explored. A county-wide geographic information system hydrologic geodatabase could provide a comprehensive picture of water use in San Miguel County and could be used by San Miguel County as a decision-support tool for future management decisions.

Medium-frequency impulsive-thrust-activated liquid hydrogen reorientation with Geyser

NASA Technical Reports Server (NTRS)

Hung, R. J.; Shyu, K. L.

1992-01-01

Efficient technique are studied for accomplishing propellant resettling through the minimization of propellant usage through impulsive thrust. A comparison between the use of constant-thrust and impulsive-thrust accelerations for the activation of propellant resettlement shows that impulsive thrust is superior to constant thrust for liquid reorientation in a reduced-gravity environment. This study shows that when impulsive thrust with 0.1-1.0-, and 10-Hz frequencies for liquid-fill levels in the range between 30-80 percent is considered, the selection of 1.0-Hz-frequency impulsive thrust over the other frequency ranges of impulsive thrust is the optimum. Characteristics of the slosh waves excited during the course of 1.0-Hz-frequency impulsive-thrust liquid reorientation were also analyzed.

Regional patterns of earthquake-triggered landslides and their relation to ground motion

NASA Astrophysics Data System (ADS)

Meunier, Patrick; Hovius, Niels; Haines, A. John

2007-10-01

We have documented patterns of landsliding associated with large earthquakes on three thrust faults: the Northridge earthquake in California, Chi-Chi earthquake in Taiwan, and two earthquakes on the Ramu-Markham fault bounding the Finisterre Mountains of Papua New Guinea. In each case, landslide densities are shown to be greatest in the area of strongest ground acceleration and to decay with distance from the epicenter. In California and Taiwan, the density of co-seismic landslides is linearly and highly correlated with both the vertical and horizontal components of measured peak ground acceleration. Based on this observation, we derive an expression for the spatial variation of landslide density analogous with regional seismic attenuation laws. In its general form, this expression applies to our three examples, and we determine best fit values for individual cases. Our findings open a window on the construction of shake maps from geomorphic observations for earthquakes in non-instrumented regions.

Stratigraphy, depositional environments, and carbonate petrology of the Toroweap and Kaibab Formations (lower Permian), Grand Canyon region, Arizona

NASA Astrophysics Data System (ADS)

Clark, R. A.

Sediments deposited in northwestern Arizona during Late Leonardian and Early Guadalupian (Permian) were controlled chiefly by an arid climate and the tectonic setting. Eastward thrusting of eugeosynclinal rocks onto miogeosynclinal deposits during Middle Devonian to Early Mississippian had a major influence on shelf sedimentation. The Toroweap and Kaibab formations represent two such platform sequences of northwestern Arizona and southern Utah deposited during this phase of sedimentation. The Toroweap Formation is subdivided into three members and represents sediments deposited during initial transgression, maximum extent of the sea, and regression (Seligman, Brady Canyon, and Woods Ranch members respectively). The Fossil Mountain Member of the Kaibab Formation documents the most extensive phase of sedimentation for all members of the Toroweap and Kaibab formations. The Harrisburg Member documents the final phase of sedimentation at the close of the Paleozoic Era.

Epigenetic lead, zinc, silver, antimony, tin, and gold veins in Boulder Basin, Blaine and Custer counties, Idaho; potential for economic tin mineralization

USGS Publications Warehouse

Ratchford, Michael E.

2002-01-01

Boulder Basin is in a northwest-trending belt of allochthonous Paleozoic rocks in the Boulder Mountains of central Idaho. Regional Tertiary extension resulted in widespread normal faulting and coeval emplacement of shallow-level intrusions and extrusive rocks of the Challis Volcanic Group. Epigenetic lead-zinc-silver-antimony-tin-gold vein deposits formed during Tertiary extension and are hosted within Paleozoic strata. The major orebodies are in the lower plate of the Boulder Basin thrust fault, in massive quartzite of the Middle Pennsylvanian to Lower Permian Wood River Formation. Anomalous concentrations of tin are present in the base-metal mineral assemblage of the Boulder Basin ore deposits. The tin-bearing veins in Boulder Basin are strikingly similar to Bolivian tin deposits. The deposit model for Bolivian tin deposits identifies buried tin porphyry below the tin-bearing vein system.

The end of the iron-core age.

NASA Technical Reports Server (NTRS)

Lyttleton, R. A.

1973-01-01

The terrestrial planets aggregated essentially from small particles, to begin as solid cool bodies with the same general compositions, and there is no possibility of an iron-core developing within any of them at any stage. Their differing internal and surface properties receive ready explanation from their different masses which determine whether the pressures within are sufficient to bring about phase-changes. The claim that the terrestrial core can be identified by means of shock-wave data as nickel-iron is based on theoretical misconception, whereas the actual seismic data establish an uncompressed-density value much lower than any such mixture could have. The onset of the Ramsey phase-change in the earth takes the form of a rapid initial collapse to produce a large core in metallic state which thereafter continues to grow secularly as a result of radioactive heating and leads to reduction of surface-area at long last adequate to account for folded and thrusted mountain-building.

Deformation of the 2002 Denali Fault earthquakes, mapped by Radarsat-1 interferometry

USGS Publications Warehouse

Lu, Zhong; Wright, Tim; Wicks, Chuck

2003-01-01

The magnitude 7.9 earthquake that struck central Alaska on 3 November 2002 was the largest strike-slip earthquake in North America for more than 150 years. The earthquake ruptured about 340 km of the Denali Fault system with observed right-lateral offsets of up to 9 m [Eberhart-Phillips et al., 2003] (Figure l). The rupture initiated with slip on a previously unknown thrust fault, the 40-km-long Susitna Glacier Fault. The rupture propagated eastward for about 220 km along the right-lateral Denali Fault where right-lateral slip averaged ˜5 m, before stepping southeastward onto the Totschunda Fault for about 70 km, with offsets as large as 2 m. The 3 November earthquake was preceded by a magnitude 6.7 shock on 23 October—the Nenana Mountain Earthquake—which was located about 25 km to the west of the 3 November earthquake.

Wilson Cycle studies

NASA Technical Reports Server (NTRS)

Burke, Kevin

1987-01-01

The main activity relating to the study during this half year was a three week field trip to study Chinese sedimentary basins (June 10 to July 3, 1986) at no cost to the project. This study, while of a reconnaissance character, permitted progress in understanding how the processes of island arc-collision and micro-continental collision operated during the Paleozoic in far western China (especially the Junggar and Tarim basins and in the intervening Tien Shan Mountains). These effects of the continuing collision of India and Asia on the area were also studied. Most specifically, these result in the elevation of the Tien Shan to more than 4 km above sea level and the depression of Turfan to move 150m below sea level. Both thrusting and large-scale strike-slip motion are important in producing these elevation changes. Some effort during the half year was also devoted to the study of greenstone-belts in terms of the Wilson Cycle.

Relationship between Biomechanical Characteristics of Spinal Manipulation and Neural Responses in an Animal Model: Effect of Linear Control of Thrust Displacement versus Force, Thrust Amplitude, Thrust Duration, and Thrust Rate

PubMed Central

Reed, William R.; Cao, Dong-Yuan; Long, Cynthia R.; Kawchuk, Gregory N.; Pickar, Joel G.

2013-01-01

High velocity low amplitude spinal manipulation (HVLA-SM) is used frequently to treat musculoskeletal complaints. Little is known about the intervention's biomechanical characteristics that determine its clinical benefit. Using an animal preparation, we determined how neural activity from lumbar muscle spindles during a lumbar HVLA-SM is affected by the type of thrust control and by the thrust's amplitude, duration, and rate. A mechanical device was used to apply a linear increase in thrust displacement or force and to control thrust duration. Under displacement control, neural responses during the HVLA-SM increased in a fashion graded with thrust amplitude. Under force control neural responses were similar regardless of the thrust amplitude. Decreasing thrust durations at all thrust amplitudes except the smallest thrust displacement had an overall significant effect on increasing muscle spindle activity during the HVLA-SMs. Under force control, spindle responses specifically and significantly increased between thrust durations of 75 and 150 ms suggesting the presence of a threshold value. Thrust velocities greater than 20–30 mm/s and thrust rates greater than 300 N/s tended to maximize the spindle responses. This study provides a basis for considering biomechanical characteristics of an HVLA-SM that should be measured and reported in clinical efficacy studies to help define effective clinical dosages. PMID:23401713

Constraints on the Velocity Structure and Accommodation of Shortening in the Atlas Mountains (Morocco) from Travel-Time Inversion of Refraction/Wide Angle Reflection Seismic Data

NASA Astrophysics Data System (ADS)

Ayarza, P.; Carbonell, R.; Palomeras, I.; Levander, A.; Teixell, A.; Zelt, C. A.; Kchikach, A.

2013-12-01

The Atlas Mountains are an intra-continental Cenozoic orogenic belt located at the southern edge of the diffuse plate boundary zone separating Africa and Europe. Its western part, the Moroccan Atlas, has long been under the scope of geoscientists investigating the origin of its high topography, locally exceeding 4000 m. Geological studies indicate that this mountain belt has experienced low to moderate shortening (<24% from balanced sections) and that topography and shortening do not keep a direct relationship. Forward modelling of the SIMA (Seismic Imaging of the Moroccan Atlas) refraction/wide angle reflection seismic data suggests that the total orogenic shortening, is resolved at depth with a Moho offset and a limited lower crust duplication that defines a 40 km-deep root in the northern part of the central High Atlas. However, the shortening accomodated by this feature (50 km) exceeds that estimated with surface data, and the position of the root appears to the north of the highest topography. In order to achieve a better definition of the crust/mantle boundary and to outline a tectonic model more coherent with surface data, we have used the RAYINVR code to carry out travel-time inversion of the SIMA data set. Inversion results depict a small shift to the south of the crustal root, formerly positioned in the northern part of the High Atlas, and define a thrusted mantle wedge. A limited crustal imbrication also appears in the Middle Atlas. The new velocity model implies complex ray trajectories but provides a better travel-time fit between the observed and the calculated data. Also, the amount of shortening implied by the this model is in agreement with that estimated from geological cross-sections. The final crustal thickness, as yet not exceeding 40 km in the root zone and less than 35 km elsewhere, still implies the need of a significant contribution from the mantle to support the topography of the Atlas mountains

Geologic Map of the Sheep Hole Mountains 30' x 60' Quadrangle, San Bernardino and Riverside Counties, California

USGS Publications Warehouse

Howard, Keith A.

2002-01-01

This data set describes and maps the geology of the Sheep Hole Mountains 30' x 60' quadrangle in southern California. The quadrangle covers an area of the Mojave Desert characterized by desert ranges separated by broad basins. Ranges include parts of the Old Woman, Ship, Iron, Coxcomb, Pinto, Bullion, and Calumet mountains as well as Lead Mountain and the Kilbeck Hills. Basins include part of Ward Valley, part of Cadiz Valley including Cadiz Lake playa, and broad valleys occupied by the Bristol Lake and Dale Lake playas. Bedrock geologic units in the ranges range in age from Proterozoic to Quaternary. The valleys expose Neogene and Quaternary deposits. Proterozoic granitoids in the quadrangle include the Early Proterozoic Fenner Gneiss, Kilbeck Gneiss, Dog Wash Gneiss, granite of Joshua Tree, the (highly peraluminous granite) gneiss of Dry Lakes valley, and a Middle Proterozoic granite. Proterozoic supracrustal rocks include the Pinto Gneiss of Miller (1938) and the quartzite of Pinto Mountain. Early Proterozoic orogeny left an imprint of metamorphic mineral assemblages and fabrics in the older rocks. A Cambrian to Triassic sequence deposited on the continental shelf lies above a profound nonconformity developed on the Proterozoic rocks. Small metamorphosed remnants of this sequence in the quadrangle include rocks correlated to the Tapeats, Bright Angel, Bonanza King, Redwall, Bird Spring, Hermit, Coconino, Kaibab, and Moenkopi formations. The Dale Lake Volcanics (Jurassic), and the McCoy Mountains Formation of Miller (1944)(Cretaceous and Jurassic?) are younger Mesozoic synorogenic supracrustal rocks in the quadrangle. Mesozoic intrusions form much of the bedrock in the quadrangle, and represent a succession of magmatic arcs. The oldest rock is the Early Triassic quartz monzonite of Twentynine Palms. Extensive Jurassic magmatism is represented by large expanses of granitoids that range in composition from gabbro to syenogranite. They include the Virginia May Quartz Monzonite and other members of the Bullion Intrusive Suite, the Chubbock Porphyry, and rocks that form the Goat Basin pluton, Music Valley pluton, and Ship Mountains pluton. The Jurassic plutons range in emplacement depths from mid-crustal to hypabysasal. Mafic and felsic dikes that probably are part of the Late Jurassic Independence dike swarm intrude the Jurassic batholithic rocks. A Mesozoic ductile fault (tectonic slide), the Scanlon thrust, places an inverted sequence of lower Paleozoic rocks and their Proterozoic basement over a lower plate of younger Paleozoic and Triassic rocks. The lower- plate rocks are internally sliced and folded. They in turn are superposed along an attenuation tectonic slide, the Kilbeck fault, over highly strained tectonic schist. The major tectonic slides and associated fabrics are cut by Late Cretaceous batholithic rocks. Widespread Late Cretaceous granitoids assigned to the Cadiz Valley batholith and the Old-Woman Piute Range batholith together form a contiguous super-unit of granite and granodiorite compositions. The Old- Woman Piute Range batholith includes the granite of Sweetwater Wash in the Painted Rock pluton and the Old Woman Mountains Granodiorite forming the Old Woman pluton. The large Cadiz Valley batholith is divided into the Iron Mountains Intrusive Suite and the Coxcomb Intrusive Suite. The Iron Mountains Intrusive Suite includes the Granite Pass Granite (which forms the Granite Pass pluton), the Danby Lake Granite Gneiss, and the Iron Granodiorite Gneiss. The Coxcomb Intrusive Suite consists of many units including the Clarks Pass Granodiorite, the Sheep Hole Mountains Granodiorite (forms the Sheep Hole Mountains pluton), and the Sheep Hole Pass Granite (forms the Sheep Hole Pass pluton). The Cretaceous rocks were emplaced at a range of deep to shallow depths, and their intrusion resulted in an aureole 2-3 km wide in older rocks. Mylonitic fabrics developed through a thickness of >1.3 km, together

Revised geologic cross sections of parts of the Colorado, White River, and Death Valley regional groundwater flow systems, Nevada, Utah, and Arizona

USGS Publications Warehouse

Page, William R.; Scheirer, Daniel S.; Langenheim, V.E.; Berger, Mary A.

2006-01-01

This report presents revisions to parts of seven of the ten cross sections originally published in U.S. Geological Survey Open-File Report 2006-1040. The revisions were necessary to correct errors in some of the original cross sections, and to show new parts of several sections that were extended and (or) appended to the original section profiles. Revisions were made to cross sections C-C', D-D', E-E', F-F', G-G', I-I', and J-J', and the parts of the sections revised or extended are highlighted below the sections on plate 1 by red brackets and the word "revised," or "extended." Sections not listed above, as well as the interpretive text and figures, are generally unchanged from the original report. Cross section C-C' includes revisions in the east Mormon Mountains in the east part of the section; D-D' includes revisions in the Mormon Mesa area in the east part of the section; E-E' includes revisions in the Muddy Mountains in the east part of the section; F-F' includes revisions from the Muddy Mountains to the south Virgin Mountains in the east part of the section; and J-J' includes some revisions from the east Mormon Mountains to the Virgin Mountains. The east end of G-G' was extended about 16 km from the Black Mountains to the southern Virgin Mountains, and the northern end of I-I' was extended about 45 km from the Muddy Mountains to the Mormon Mountains, and revisions were made in the Muddy Mountains part of the original section. This report contains 10 interpretive cross sections and an integrated text describing the geology of parts of the Colorado, White River, and Death Valley regional groundwater flow systems in Nevada, Utah, and Arizona. The primary purpose of the report is to provide geologic framework data for input into a numerical groundwater model. Therefore, the stratigraphic and structural summaries are written in a hydrogeologic context. The oldest rocks (basement) are Early Proterozoic metamorphic and intrusive crystalline rocks that are considered confining units because of their low permeability. Late Proterozoic to Lower Cambrian clastic units overlie the crystalline rocks and are also considered confining units within the regional flow systems. Above the clastic units are Middle Cambrian to Lower Permian carbonate rocks that are the primary aquifers in the flow systems. The Middle Cambrian to Lower Permian carbonate rocks are overlain by a sequence of mainly clastic rocks of late Paleozoic to Mesozoic age that are mostly considered confining units, but they may be permeable where faulted. Tertiary volcanic and plutonic rocks are exposed in the northern and southern parts of the study area. In the Clover and Delamar Mountains, these rocks are highly deformed by north- and northwest-striking normal and strike-slip faults that are probably important conduits in transmitting groundwater from the basins in the northern Colorado and White River flow systems to basins in the southern part of the flow systems. The youngest rocks in the region are Tertiary to Quaternary basin-fill deposits. These rocks consist of middle to late Tertiary sediments consisting of limestone, conglomerate, sandstone, tuff, and gypsum, and younger Quaternary surficial units consisting of alluvium, colluvium, playa deposits, and eolian deposits. Basin-fill deposits are both aquifers and aquitards. The rocks in the study area were complexly deformed by episodes of Mesozoic compression and Cenozoic extensional tectonism. Some Cretaceous thrust faults and folds of the Sevier orogenic belt form duplex zones and define areas of maximum thickness for the Paleozoic carbonate rocks. Cenozoic faults are important because they are the primary structures that control groundwater flow in the regional flow systems.

Uncertainty of in-flight thrust determination

NASA Technical Reports Server (NTRS)

Abernethy, Robert B.; Adams, Gary R.; Steurer, John W.; Ascough, John C.; Baer-Riedhart, Jennifer L.; Balkcom, George H.; Biesiadny, Thomas

1986-01-01

Methods for estimating the measurement error or uncertainty of in-flight thrust determination in aircraft employing conventional turbofan/turbojet engines are reviewed. While the term 'in-flight thrust determination' is used synonymously with 'in-flight thrust measurement', in-flight thrust is not directly measured but is determined or calculated using mathematical modeling relationships between in-flight thrust and various direct measurements of physical quantities. The in-flight thrust determination process incorporates both ground testing and flight testing. The present text is divided into the following categories: measurement uncertainty methodoogy and in-flight thrust measurent processes.

Geophysical Evidence for the Tectonic Evolution of the Inverted Belt-Purcell Basin, Northwestern Montana

NASA Astrophysics Data System (ADS)

Rutherford, B. S.; Speece, M. A.; Constenius, K. N.

2015-12-01

The geometry of the Precambrian Belt-Purcell basin and subsequent allochthon, that dominates the geology of northwestern Montana, played a critical role in the development of compressional structures during orogenesis and their ensuing reactivation during the later phase of extensional collapse. Five reprocessed seismic reflection profiles provide images in the Swan Range and adjacent valleys that we have correlated to published seismic data north into Canada. Reflections from syndepositional sills encased within Lower Belt rocks offer clues to the configuration of the basin prior to its tectonic inversion. Thick basinal facies of the Lewis salient are contrasted by thin shelfal facies found in hanging wall rocks of frontal Belt carrying thrusts south of the salient. The along strike change in hanging wall rocks reflects the original configuration of the Belt basin margin. Rocks of the Lewis salient were deposited in an embayment on the northeastern margin of the Belt basin. Shelfal accumlations of the embayment comprise an autochthonous wedge that has remained in the footwall of the Lewis thrust system. South of the embayment and related salient, nearly the entire Belt basin was detached from pre-Belt crystalline rocks and inverted at the latitude of the Sawtooth Range. Deeply exhumed Phanerozoic rocks of the Sawtooth Range are a direct consequence of the thin wedge geometry of the detached basin south of the Lewis salient that required growth of a substantial orogenic wedge to obtain critical taper values. We offer an alternate interpretation of a >10 km high, west facing décollement ramp that coincides with the Belt-Purcell basin margin. Previous interpretations in Montana have inferred the location of the basin margin ramp to approximate the trace of the Purcell Anticlinorium. Seismic data and cross-section balancing suggest the Rocky Mountain Trench as a more accurate location. Based on our proposed position of the basin margin the Belt-Purcell allocthon requires insignificant rotation during thrust emplacement which is in agreement with published interpretations of paleomagnetic data. We suggest small (<5°) clockwise rotation is due to an increase in extensional slip from the international border south to the Flathead Valley as opposed to an increase in compressional shortening to the north.The geometry of the Precambrian Belt-Purcell basin and subsequent allochthon, that dominates the geology of northwestern Montana, played a critical role in the development of compressional structures during orogenesis and their ensuing reactivation during the later phase of extensional collapse. Five reprocessed seismic reflection profiles provide images in the Swan Range and adjacent valleys that we have correlated to published seismic data north into Canada. Reflections from syndepositional sills encased within Lower Belt rocks offer clues to the configuration of the basin prior to its tectonic inversion. Thick basinal facies of the Lewis salient are contrasted by thin shelfal facies found in hanging wall rocks of frontal Belt carrying thrusts south of the salient. The along strike change in hanging wall rocks reflects the original configuration of the Belt basin margin. Rocks of the Lewis salient were deposited in an embayment on the northeastern margin of the Belt basin. Shelfal accumlations of the embayment comprise an autochthonous wedge that has remained in the footwall of the Lewis thrust system. South of the embayment and related salient, nearly the entire Belt basin was detached from pre-Belt crystalline rocks and inverted at the latitude of the Sawtooth Range. Deeply exhumed Phanerozoic rocks of the Sawtooth Range are a direct consequence of the thin wedge geometry of the detached basin south of the Lewis salient that required growth of a substantial orogenic wedge to obtain critical taper values. We offer an alternate interpretation of a >10 km high, west facing décollement ramp that coincides with the Belt-Purcell basin margin. Previous interpretations in Montana have inferred the location of the basin margin ramp to approximate the trace of the Purcell Anticlinorium. Seismic data and cross-section balancing suggest the Rocky Mountain Trench as a more accurate location. Based on our proposed position of the basin margin the Belt-Purcell allocthon requires insignificant rotation during thrust emplacement which is in agreement with published interpretations of paleomagnetic data. We suggest small (<5°) clockwise rotation is due to an increase in extensional slip from the international border south to the Flathead Valley as opposed to an increase in compressional shortening to the north.

Revolutionizing Space Propulsion Through the Characterization of Iodine as Fuel for Hall-Effect Thrusters

DTIC Science & Technology

2011-03-01

for controlled thruster operation at varying conditions. An inverted pendulum was used to take thrust measurements. Thrust to power ratio, anode...for comparison will include thrust, T. Thrust 21 can be measured by a sensitive inverted pendulum thrust stand. Specific impulse would be...to this pressure. III.4 Diagnostic Equipment The instrument used to take thrust measurements was the Busek T8 inverted pendulum thrust stand [13

Was Himalayan normal faulting triggered by initiation of the Ramgarh-Munsiari Thrust?

USGS Publications Warehouse

Robinson, Delores M.; Pearson, Ofori N.

2013-01-01

The Ramgarh–Munsiari thrust is a major orogen-scale fault that extends for more than 1,500 km along strike in the Himalayan fold-thrust belt. The fault can be traced along the Himalayan arc from Himachal Pradesh, India, in the west to eastern Bhutan. The fault is located within the Lesser Himalayan tectonostratigraphic zone, and it translated Paleoproterozoic Lesser Himalayan rocks more than 100 km toward the foreland. The Ramgarh–Munsiari thrust is always located in the proximal footwall of the Main Central thrust. Northern exposures (toward the hinterland) of the thrust sheet occur in the footwall of the Main Central thrust at the base of the high Himalaya, and southern exposures (toward the foreland) occur between the Main Boundary thrust and Greater Himalayan klippen. Although the metamorphic grade of rocks within the Ramgarh–Munsiari thrust sheet is not significantly different from that of Greater Himalayan rock in the hanging wall of the overlying Main Central thrust sheet, the tectonostratigraphic origin of the two different thrust sheets is markedly different. The Ramgarh–Munsiari thrust became active in early Miocene time and acted as the roof thrust for a duplex system within Lesser Himalayan rocks. The process of slip transfer from the Main Central thrust to the Ramgarh–Munsiari thrust in early Miocene time and subsequent development of the Lesser Himalayan duplex may have played a role in triggering normal faulting along the South Tibetan Detachment system.

High-power, null-type, inverted pendulum thrust stand.

PubMed

Xu, Kunning G; Walker, Mitchell L R

2009-05-01

This article presents the theory and operation of a null-type, inverted pendulum thrust stand. The thrust stand design supports thrusters having a total mass up to 250 kg and measures thrust over a range of 1 mN to 5 N. The design uses a conventional inverted pendulum to increase sensitivity, coupled with a null-type feature to eliminate thrust alignment error due to deflection of thrust. The thrust stand position serves as the input to the null-circuit feedback control system and the output is the current to an electromagnetic actuator. Mechanical oscillations are actively damped with an electromagnetic damper. A closed-loop inclination system levels the stand while an active cooling system minimizes thermal effects. The thrust stand incorporates an in situ calibration rig. The thrust of a 3.4 kW Hall thruster is measured for thrust levels up to 230 mN. The uncertainty of the thrust measurements in this experiment is +/-0.6%, determined by examination of the hysteresis, drift of the zero offset and calibration slope variation.

Pulsed Electric Propulsion Thrust Stand Calibration Method

NASA Technical Reports Server (NTRS)

Wong, Andrea R.; Polzin, Kurt A.; Pearson, J. Boise

2011-01-01

The evaluation of the performance of any propulsion device requires the accurate measurement of thrust. While chemical rocket thrust is typically measured using a load cell, the low thrust levels associated with electric propulsion (EP) systems necessitate the use of much more sensitive measurement techniques. The design and development of electric propulsion thrust stands that employ a conventional hanging pendulum arm connected to a balance mechanism consisting of a secondary arm and variable linkage have been reported in recent publications by Polzin et al. These works focused on performing steady-state thrust measurements and employed a static analysis of the thrust stand response. In the present work, we present a calibration method and data that will permit pulsed thrust measurements using the Variable Amplitude Hanging Pendulum with Extended Range (VAHPER) thrust stand. Pulsed thrust measurements are challenging in general because the pulsed thrust (impulse bit) occurs over a short timescale (typically 1 micros to 1 millisecond) and cannot be resolved directly. Consequently, the imparted impulse bit must be inferred through observation of the change in thrust stand motion effected by the pulse. Pulsed thrust measurements have typically only consisted of single-shot operation. In the present work, we discuss repetition-rate pulsed thruster operation and describe a method to perform these measurements. The thrust stand response can be modeled as a spring-mass-damper system with a repetitive delta forcing function to represent the impulsive action of the thruster.

Permanent GPS network around the bend of the Jura Arc: preliminary results

NASA Astrophysics Data System (ADS)

Sue, Christian; Walpersdorf, Andrea; Sakic, Pierre; Rabin, Mickael; Champagnac, Jean daniel

2014-05-01

The Jura Mountain, the westernmost belt of the alpine orogeny, is one of the best-studied orogenic arcs in the world. The Jura arc is a typical fold-and-thrust belt, with a main décollement thrust localized in the Triasic evaporites under the Jurassic-Cretaceous series. It is directly linked to the alpine orogenic wedge, especially in term of critical taper. It is supposed to be still active in collision mode, which would rise up the issue of its relation with the Alps to the East, currently undergoing post-orogenic gravitational potential adjustment. Nevertheless, its current activity and recent deformation remain a matter of debate, few neotectonic-related data being available in this area. The Jura is crosscut by left-lateral strike-slip faults in a radial scheme with respect to the arc, and recent seismicity along one of them, the Vuache fault (Annecy earthquake Ml 5.3 1996), and at the northern front of the belt (Beaume-les-Dames earthquake, Ml 5.1, 2004), argues for ongoing active deformation across the Jura Mountain. Here we present preliminary results of permanent GPS network surrounding the Jura belt (RENAG and RPG data), which tend to show very slow, yet self-consistent strain pattern of the order of some tenth of mm/yr over 100 km-long typical baselines, with shortening perpendicular to the arc, and extension parallel to its axial trend. We also characterize a slow uplift in the same order of magnitude, which appears to be correlated to the current uplift observed in the Alps. Indeed, the uplift velocities are continuously decreasing from the core of the Alps (+2 mm/yr) to the westernmost part of the Jura (+0,4 mm/yr) and to the stable foreland (-0.1 mm/yr). Actually, from the Po plain to the Jura foreland, the GPS-related uplift velocities are well correlated to the topography, and the Jura arc appears connected to the Alps from this point of view. In order to better determine the deformation pattern in the Jura arc, we present a new regional GNSS permanent network (GPS-JURA, Besançon observatory) developed at the end of 2013, which will allow in a near future to accurately characterize and quantify the current strain pattern of this emblematic arc.

Geologic map and upper Paleozoic stratigraphy of the Marble Canyon area, Cottonwood Canyon quadrangle, Death Valley National Park, Inyo County, California

USGS Publications Warehouse

Stone, Paul; Stevens, Calvin H.; Belasky, Paul; Montañez, Isabel P.; Martin, Lauren G.; Wardlaw, Bruce R.; Sandberg, Charles A.; Wan, Elmira; Olson, Holly A.; Priest, Susan S.

2014-01-01

This geologic map and pamphlet focus on the stratigraphy, depositional history, and paleogeographic significance of upper Paleozoic rocks exposed in the Marble Canyon area in Death Valley National Park, California. Bedrock exposed in this area is composed of Mississippian to lower Permian (Cisuralian) marine sedimentary rocks and the Jurassic Hunter Mountain Quartz Monzonite. These units are overlain by Tertiary and Quaternary nonmarine sedimentary deposits that include a previously unrecognized tuff to which we tentatively assign an age of late middle Miocene (~12 Ma) based on tephrochronologic analysis, in addition to the previously recognized Pliocene tuff of Mesquite Spring. Mississippian and Pennsylvanian rocks in the Marble Canyon area represent deposition on the western continental shelf of North America. Mississippian limestone units in the area (Tin Mountain, Stone Canyon, and Santa Rosa Hills Limestones) accumulated on the outer part of a broad carbonate platform that extended southwest across Nevada into east-central California. Carbonate sedimentation was interrupted by a major eustatic sea-level fall that has been interpreted to record the onset of late Paleozoic glaciation in southern Gondwana. Following a brief period of Late Mississippian clastic sedimentation (Indian Springs Formation), a rise in eustatic sea level led to establishment of a new carbonate platform that covered most of the area previously occupied by the Mississippian platform. The Pennsylvanian Bird Spring Formation at Marble Canyon makes up the outer platform component of ten third-order (1 to 5 m.y. duration) stratigraphic sequences recently defined for the regional platform succession. The regional paleogeography was fundamentally changed by major tectonic activity along the continental margin beginning in middle early Permian time. As a result, the Pennsylvanian carbonate shelf at Marble Canyon subsided and was disconformably overlain by lower Permian units (Osborne Canyon and Darwin Canyon Formations) representing part of a deep-water turbidite basin filled primarily by fine-grained siliciclastic sediment derived from cratonal sources to the east. Deformation and sedimentation along the western part of this basin continued into late Permian time. The culminating phase was part of a regionally extensive late Permian thrust system that included the Marble Canyon thrust fault just west of the present map area.

Thrust Measurement of Dielectric Barrier Discharge (DBD) Plasma Actuators: New Anti-Thrust Hypothesis, Frequency Sweeps Methodology, Humidity and Enclosure Effects

NASA Technical Reports Server (NTRS)

Ashpis, David E.; Laun, Matthew C.

2014-01-01

We discuss thrust measurements of Dielectric Barrier Discharge (DBD) plasma actuators devices used for aerodynamic active flow control. After a review of our experience with conventional thrust measurement and significant non-repeatability of the results, we devised a suspended actuator test setup, and now present a methodology of thrust measurements with decreased uncertainty. The methodology consists of frequency scans at constant voltages. The procedure consists of increasing the frequency in a step-wise fashion from several Hz to the maximum frequency of several kHz, followed by frequency decrease back down to the start frequency of several Hz. This sequence is performed first at the highest voltage of interest, then repeated at lower voltages. The data in the descending frequency direction is more consistent and selected for reporting. Sample results show strong dependence of thrust on humidity which also affects the consistency and fluctuations of the measurements. We also observed negative values of thrust, or "anti-thrust", at low frequencies between 4 Hz and up to 64 Hz. The anti-thrust is proportional to the mean-squared voltage and is frequency independent. Departures from the parabolic anti-thrust curve are correlated with appearance of visible plasma discharges. We propose the anti-thrust hypothesis. It states that the measured thrust is a sum of plasma thrust and anti-thrust, and assumes that the anti-thrust exists at all frequencies and voltages. The anti-thrust depends on actuator geometry and materials and on the test installation. It enables the separation of the plasma thrust from the measured total thrust. This approach enables more meaningful comparisons between actuators at different installations and laboratories. The dependence on test installation was validated by surrounding the actuator with a grounded large-diameter metal sleeve. Strong dependence on humidity is also shown; the thrust significantly increased with decreasing humidity, e.g., 44 percent increase as relative humidity changed from 18 percent and dew point 33 degF to 50 percent and dew point of 57 degF.

Characterization of Space Shuttle Reusable Rocket Motor Static Test Stand Thrust Measurements

NASA Technical Reports Server (NTRS)

Cook, Mart L.; Gruet, Laurent; Cash, Stephen F. (Technical Monitor)

2003-01-01

Space Shuttle Reusable Solid Rocket Motors (RSRM) are static tested at two ATK Thiokol Propulsion facilities in Utah, T-24 and T-97. The newer T-97 static test facility was recently upgraded to allow thrust measurement capability. All previous static test motor thrust measurements have been taken at T-24; data from these tests were used to characterize thrust parameters and requirement limits for flight motors. Validation of the new T-97 thrust measurement system is required prior to use for official RSRM performance assessments. Since thrust cannot be measured on RSRM flight motors, flight motor measured chamber pressure and a nominal thrust-to-pressure relationship (based on static test motor thrust and pressure measurements) are used to reconstruct flight motor performance. Historical static test and flight motor performance data are used in conjunction with production subscale test data to predict RSRM performance. The predicted motor performance is provided to support Space Shuttle trajectory and system loads analyses. Therefore, an accurate nominal thrust-to-pressure (F/P) relationship is critical for accurate RSRM flight motor performance and Space Shuttle analyses. Flight Support Motors (FSM) 7, 8, and 9 provided thrust data for the validation of the T-97 thrust measurement system. The T-97 thrust data were analyzed and compared to thrust previously measured at T-24 to verify measured thrust data and identify any test-stand bias. The T-97 FIP data were consistent and within the T-24 static test statistical family expectation. The FSMs 7-9 thrust data met all NASA contract requirements, and the test stand is now verified for future thrust measurements.

Design and evaluation of thrust vectored nozzles using a multicomponent thrust stand

NASA Technical Reports Server (NTRS)

Carpenter, Thomas W.; Blattner, Ernest W.; Stagner, Robert E.; Contreras, Juanita; Lencioni, Dennis; Mcintosh, Greg

1990-01-01

Future aircraft with the capability of short takeoff and landing, and improved maneuverability especially in the post-stall flight regime will incorporate exhaust nozzles which can be thrust vectored. In order to conduct thrust vector research in the Mechanical Engineering Department at Cal Poly, a program was planned with two objectives; design and construct a multicomponent thrust stand for the specific purpose of measuring nozzle thrust vectors; and to provide quality low moisture air to the thrust stand for cold flow nozzle tests. The design and fabrication of the six-component thrust stand was completed. Detailed evaluation tests of the thrust stand will continue upon the receipt of one signal conditioning option (-702) for the Fluke Data Acquisition System. Preliminary design of thrust nozzles with air supply plenums were completed. The air supply was analyzed with regard to head loss. Initial flow visualization tests were conducted using dual water jets.

Paleoseismic investigations at the Cal thrust fault, Mendoza, Argentina

NASA Astrophysics Data System (ADS)

Salomon, Eric; Schmidt, Silke; Hetzel, Ralf; Mingorance, Francisco

2010-05-01

Along the active mountain front of the Andean Precordillera between 30°S and 34°S in western Argentina several earthquakes occurred in recent times, including a 7.0 Ms event in 1861 which destroyed the city of Mendoza and killed two thirds of its population. The 1861 event and two other earthquakes (Ms = 5.7 in 1929 and Ms = 5.6 in 1967) were generated on the Cal thrust fault, which extends over a distance of 31 km north-south and runs straight through the center of Mendoza. In the city, which has now more than 1 million inhabitants, the fault forms a 3-m-high fault scarp. Although the Cal thrust fault poses a serious seismic hazard, the paleoseismologic history of this fault and its long-term slip rate remains largely unknown (Mingorance, 2006). We present the first results of an ongoing paleoseismologic study of the Cal thrust at a site located 5 km north of Mendoza. Here, the fault offsets Late Holocene alluvial fan sediments by 2.5 m vertically and exhibits a well developed fault scarp. A 15-m-long and 2-3-m-deep trench across the scarp reveals three east-vergent folds that we interpret to have formed during three earthquakes. Successive retrodeformation of the two youngest folds suggests that the most recent event (presumably the 1861 earthquake) caused ~1.1 m of vertical offset and ~1.8 m of horizontal shortening. For the penultimate event we obtain a vertical offset of ~0.7 m and a horizontal shortening of ~1.9 m. A vertical displacement of ~0.7 m observed on a steeply west-dipping fault may be associated with an older event. The cumulative vertical offset of 2.5 m for the three inferred events is in excellent agreement with the height of the scarp. Based on the retrodeformation of the trench deposits the fault plane dips ~25° to the west. In the deepest part of the trench evidence for even older seismic events is preserved beneath an angular unconformity that was formed during a period of erosion and pre-dates the present-day scarp. Dating of samples to determine the recurrence interval of these seismic events and the long-term slip rate of the fault is in progress. References Mingorance, F. (2006): Morfometría de la escarpa de falla historica identificada al norte del cerro La Cal, zona de falla La Cal, Mendoza. Revista de la Asociación Geológica Argentina, 61 (4), 620-638.

Late Neogene and Active Tectonics along the Northern Margin of the Central Anatolian Plateau,TURKEY

NASA Astrophysics Data System (ADS)

Yildirim, C.; Schildgen, T. F.; Melnick, D.; Echtler, H. P.; Strecker, M. R.

2009-12-01

Margins of orogenic plateaus are conspicuous geomorphic provinces that archive tectonic and climatic variations related to surface uplift. Their growth is associated with spatial and temporal variations of mode and rate of tectonics and surface processes. Those processes can be strongly linked to the evolution of margins and plateaus thorough time. As one of the major morpho-tectonic provinces of Turkey, the Central Pontides (coinciding with the northern margin of the Central Anatolian Plateau (CAP)) display a remarkable topography and present valuable geologic and geomorphic indicators to identify active tectonics. Morpho-tectonic analysis, geological cross-sections, seismic profiles, and geodetic analysis reveal continuous deformation characterized by brittle faults from Late Miocene to recent across the northern margin of the CAP. In the Sinop Peninsula and offshore in the southern Black Sea, pervasive faulting and folding and uplift of Late Miocene to Quaternary marine deposits is related to active margin tectonics of the offshore southern Black Sea thrust and the onshore Balifaki and Erikli faults. In the Kastamonu-Boyabat sedimentary basin, the Late Miocene to Quaternary continental equivalents are strongly deformed by the Ekinveren Fault. This vergent inverse and thrust fault with overstepping en echelon segments deforms not only Quaternary travertines and conglomerates, but also patterns of the Pleistocene to Holocene drainage systems. In the southern Kastamonu-Boyabat basin, an antithetic thrust fault of the Ekinveren Fault system deformed also Quaternary fluviatile terrace deposits. Farther south, a dextral transpressive splay of the North Anatolian Fault (NAF) deforms pediment surfaces and forms the northern flank of the Ilgaz active mountain range. The Ilgaz Range rises up to 2587 m.a.s.l and is delimited by active segments of the NAF.The Central Pontides are located at the apex of northward convex arc of the NAF. Geodetic analysis indicate a deviation of the slip vectors and strain partitioning in the Central Pontides due to the large restraining bend geometry of the NAF. DEM analysis and field observations reveal that the Central Pontides integrate an active bivergent wedge, indicating out-of sequence thrusting and topographical asymmetry, with a gentle pro-wedge northern slope and a steep retro-wedge southern slopes, and regional surface tilting from south to north. Uplifted presumably Late Pleistocene to Holocene marine terraces 4 to 40 m.a.s.l. along the coast and well developed pediment and fill and strath terrace surfaces ranging from 10 to 300 m above along the Gokirmak and Kizilirmak rivers will provide chronological constraints on the uplift and incision rates of the study area.

Development of a glacially dominated shelf-slope-fan system in tectonically active southeast Alaska: Results of IODP Expedition 341 core-log-seismic integrated studies at glacial cycle resolution

NASA Astrophysics Data System (ADS)

Gulick, Sean; Jaeger, John; Mix, Alan; Swartz, John; Worthington, Lindsay; Reece, Robert

2014-05-01

Collision of the Yakutat microplate with North American formed the St. Elias Mountains in coastal Gulf of Alaska. While the tectonic driver for orogenesis has been ongoing since the Miocene, results from the Integrated Ocean Drilling Program Expedition 341 suggests that direct climatic perturbation of active orogenesis through glacial erosion is non-linear. Geophysical studies of the glaciated continental margin, slope, and adjacent deep-sea Surveyor Fan allow examination of the glaciated orogen from source to sink. Using high-resolution and crustal-scale seismic data and through comparison with other glaciated margins, we can identify key diagnostic seismic morphologies and facies indicative of glacial proximity and sediment routing. Expedition drilling results calibrated these images suggesting a timeline for initial advances of the Cordilleran ice sheet related glacial systems onto the shelf and a further timeline for the development of ice streams that reach the shelf edge. Comparisons can be made within this single margin between evolution of the tectonic-glacial system where erosion and sediment transport are occurring within a fold and thrust belt versus on a more stable shelf region. Onshore the Bering-Bagley glacial system in the west flows across the Yakataga fold and thrust belt, allowing examination of whether glacial erosion can cause tectonic feedbacks, whereas offshore the Bering-Bagley system interacts with the Pamplona Zone thrusts in a region of significant sediment accommodation. Results from Expedition 341 imply that timing of glacial advance to the shelf edge in this region may be driven by the necessity of filling up the accommodation through aggradation followed by progradation and thus is autogenic. In contrast the Malaspina-Hubbard glacial system to the east encountered significantly less accommodation and more directly responded to climatic forcing including showing outer shelf glacial occupation since the mid-Pleistocene transition-MPT to 100 kyr glacial-interglacial cycles. Examination of the sink for both of these systems, which includes the Surveyor Fan and Aleutian Trench wedge, demonstrates a clear climatic driver for sediment flux to the deep sea. The first appearance of ice-rafted debris at our distal drill site closely approximates the start of the Pleistocene and a doubling of sediment accumulation accompanies the MPT. Converting sediment volumes just within the deep-sea sinks back to erosion rates in the orogen and correlating with changes in exhumation rates from thermochronology demonstrates a lack of accelerated tectonic response to the intensification of Northern Hemisphere glaciations at the start of the Pleistocene but increased shortening and exhumation of sediments at the MPT. The form of tectonic response differs between out-of-sequence thrusting or antiformal stacking within the fold and thrust belt to the west and a near vertical advection of material in a tectonic aneurysm in the core of the orogen to the east.

Uncoupled vs. coupled thrust belt-foreland deformation: a model for northern Patagonia inferred from U-Th/He and apatite fission track dating

NASA Astrophysics Data System (ADS)

Savignano, Elisa; Mazzoli, Stefano; Zattin, Massimiliano; Gautheron, Cécile; Franchini, Marta

2017-04-01

The study of the Cretaceous - Cenozoic evolution of the Patagonian Andes represents a great opportunity to investigate the effects of coupling between deep lithospheric processes and near-surface deformation. Low-temperature thermochronological systems are ideally suited for detecting events involving rocks in the uppermost part of the crust because they record time and rates of cooling related to exhumation of the top few kilometers of the crust. The Patagonia region, although characterized by a general continuity of the Andean orogen along its strike, shows an appreciable internal tectonic segmentation (marked by a variable position of the magmatic arc and of the deformation front in the retroarc area) at various latitudes. This complex structural architecture has been interpreted as the result of different processes acting since the Late Cretaceous. The present-day configuration of the southern Andes is interpreted to have been controlled by alternating stages of flat- and steep-slab subduction, which produced shortening and upper plate extension episodes,, respectively. Furthermore, the deformation in this whole retroarc sector varied not only in time (i.e. with major 'cycles' of mountain building and orogenic collapse), but also in space, due to the variable transmission of horizontal compressive stress away from the orogen, that produced an irregular unroofing pattern. In this study, we have integrated field structural observations with new apatite (U-Th)/He data (AHe) and apatite fission-track (AFT) ages in the north Patagonia region (at latitudes between 40° and 44°S) in order to analyse and compare the exhumation patterns from the frontal part of the orogen and from the adjacent foreland sector, as well as to gain new insights into the timing and modes of coupling vs. uncoupling of the deformation between the northern Patagonian fold and thrust belt and its foreland. The obtained data indicate a markedly different unroofing pattern between the 'broken foreland' area (characterized by Late Cretaceous to Paleogene exhumation) and the adjacent Andean sector to the west, which is dominated by Miocene-Pliocene exhumation. Our study supports the idea that the configuration of the slab (flat vs. steep) during subduction controls the coupling vs. uncoupling of the deformation between the thrust belt and the foreland. Along the studied transect, late Miocene to Pliocene AHe ages from the frontal part of the northern Patagonian Andes correlate well with a rapid recent shortening and exhumation stage that took place in the thrust belt during steep-slab subduction and rollback. On the other hand, AHe ages obtained for the 'broken foreland' unravelled exhumation at near-surface conditions during Late Cretaceous to Paleogene times, when a prolonged phase of flat-slab subduction favoured the coupling between the thrust belt and the foreland area and associated widespread shortening able to reactivate inherited rift-related structures.

Mineral resources of Elko County, Nevada

USGS Publications Warehouse

Smith, Roscoe Maurice

1976-01-01

Of the 66 named mining districts in Elko County, 56 have been productive of one or more of 19 different commodities: 11 metals--copper, gold, silver, lead, zinc, mercury, tungsten, manganese, iron, uranium, and antimony; 8 nonmetals--sand and gravel, stone, barite, diatomite, gems, oil shale, volcanic ash, and clay. In addition to the commodities produced, at least 5 others--beryllium, molybdenum, tin, phosphorite, and petroleum, occur in amounts sufficient to warrant exploration. The other districts have been explored, but no production has been recorded. Total value-when-sold of production recorded through 1969 was nearly $91 million; actual production was considerably greater, especially if sand and gravel, barite, and other nonmetallic products before 1953 are included. In value of metals produced, the five highest districts are Mountain City ($26 million), Tuscarora ($11 million), Jarbidge ($10 million), Aura ($6 million), and Railroad (nearly $5 million). The Rio Tinto copper mine in the Mountain City district yielded $21 million. Of the 17 districts that produced nonmetallic minerals, Bootstrap .is the largest producer, containing the Rossi mine, one of the two largest barite mines in the United States. Most of /he metals produced name from veins and replacement deposits in limestone or dolomite near granitic stocks; exceptions are manganese and mercury, which are not associated with known or inferred stocks; mercury is further excepted because it occurs in volcanic rocks, as do a few deposits of the major metals. The largest deposit--the Rio Tinto lode--was a combination of fissure filling and replacement along a bedding plane shear zone 150 ft wide and 1,200 ft long in carbonaceous shale of the Valmy Formation; this deposit is apparently older than the Mountain City stock and its mineralization may be related to Paleozoic mafic volcanism later than a major thrust fault, inferred to underlie the area at a depth of about 5,000 ft. Most of the nonmetallic minerals mined were sedimentary bedded deposits, but mica was mined from pegmatite deposits, and turquoise from both placer and hydrothermal deposits. The largest known reserves of metals (1973) are of porphyry copper in the Dolly Varden district and gold in the Bootstrap district. Reserves of barite also are presumed to be large. The greatest potential for future production of metals, notably copper and gold, appears to be in the known districts or extensions of them and peripheral to deposits that are related to known or concealed plutons and thrust faults. Potential resources in deposits too low in grade to be worked profitably at the present time include all commodities that have been produced and, in addition, known, deposits of beryllium, molybdenum, tin, and phosphorite. Speculative resources in undiscovered deposits may reasonably be predicted to include all known commodities as well as others that are unsuspected. Petroleum may yet be produced from the Elko Formation and geothermal energy from the Ruby Valley and Elko areas.

Measurement of Impulsive Thrust from a Closed Radio Frequency Cavity in Vacuum

NASA Technical Reports Server (NTRS)

White, Harold; March, Paul; Lawrence, James; Vera, Jerry; Sylvester, Andre; Brady, David; Bailey, Paul

2016-01-01

A vacuum test campaign evaluating the impulsive thrust performance of a tapered RF test article excited in the TM212 mode at 1,937 megahertz (MHz) has been completed. The test campaign consisted of a forward thrust phase and reverse thrust phase at less than 8 x 10(exp -6) Torr vacuum with power scans at 40 watts, 60 watts, and 80 watts. The test campaign included a null thrust test effort to identify any mundane sources of impulsive thrust, however none were identified. Thrust data from forward, reverse, and null suggests that the system is consistently performing with a thrust to power ratio of 1.2 +/- 0.1 mN/kW.

Quiet Clean Short-Haul Experimental Engine (QCSEE) acoustic and aerodynamic tests on a scale model over-the-wing thrust reverser and forward thrust nozzle

NASA Technical Reports Server (NTRS)

Stimpert, D. L.

1978-01-01

An acoustic and aerodynamic test program was conducted on a 1/6.25 scale model of the Quiet, Clean, Short-Haul Experimental Engine (QCSEE) forward thrust over-the-wing (OTW) nozzle and OTW thrust reverser. In reverse thrust, the effect of reverser geometry was studied by parametric variations in blocker spacing, blocker height, lip angle, and lip length. Forward thrust nozzle tests determined the jet noise levels of the cruise and takeoff nozzles, the effect of opening side doors to achieve takeoff thrust, and scrubbing noise of the cruise and takeoff jet on a simulated wing surface. Velocity profiles are presented for both forward and reverse thrust nozzles. An estimate of the reverse thrust was made utilizing the measured centerline turning angle.

Development of a two-dimensional dual pendulum thrust stand for Hall thrusters.

PubMed

Nagao, N; Yokota, S; Komurasaki, K; Arakawa, Y

2007-11-01

A two-dimensional dual pendulum thrust stand was developed to measure thrust vectors [axial and horizontal (transverse) direction thrusts] of a Hall thruster. A thruster with a steering mechanism is mounted on the inner pendulum, and thrust is measured from the displacement between inner and outer pendulums, by which a thermal drift effect is canceled out. Two crossover knife-edges support each pendulum arm: one is set on the other at a right angle. They enable the pendulums to swing in two directions. Thrust calibration using a pulley and weight system showed that the measurement errors were less than 0.25 mN (1.4%) in the main thrust direction and 0.09 mN (1.4%) in its transverse direction. The thrust angle of the thrust vector was measured with the stand using the thruster. Consequently, a vector deviation from the main thrust direction of +/-2.3 degrees was measured with the error of +/-0.2 degrees under the typical operating conditions for the thruster.

Initiation process of a thrust fault revealed by analog experiments

NASA Astrophysics Data System (ADS)

Yamada, Yasuhiro; Dotare, Tatsuya; Adam, Juergen; Hori, Takane; Sakaguchi, Hide

2016-04-01

We conducted 2D (cross-sectional) analog experiments with dry sand using a high resolution digital image correlation (DIC) technique to reveal initiation process of a thrust fault in detail, and identified a number of "weak shear bands" and minor uplift prior to the thrust initiation. The observations suggest that the process can be divided into three stages. Stage 1: characterized by a series of abrupt and short-lived weak shear bands at the location where the thrust will be generated later. Before initiation of the fault, the area to be the hanging wall starts to uplift. Stage 2: defined by the generation of the new thrust and its active displacement. The location of the new thrust seems to be constrained by its associated back-thrust, produced at the foot of the surface slope (by the previous thrust). The activity of the previous thrust turns to zero once the new thrust is generated, but the timing of these two events is not the same. Stage 3: characterized by a constant displacement along the (new) thrust. Similar minor shear bands can be seen in the toe area of the Nankai accretionary prism, SW Japan and we can correlate the along-strike variations in seismic profiles to the model results that show the characteristic features in each thrust development stage.

Interpretation of the Seattle uplift, Washington, as a passive-roof duplex

USGS Publications Warehouse

Brocher, T.M.; Blakely, R.J.; Wells, R.E.

2004-01-01

We interpret seismic lines and a wide variety of other geological and geophysical data to suggest that the Seattle uplift is a passive-roof duplex. A passive-roof duplex is bounded top and bottom by thrust faults with opposite senses of vergence that form a triangle zone at the leading edge of the advancing thrust sheet. In passive-roof duplexes the roof thrust slips only when the floor thrust ruptures. The Seattle fault is a south-dipping reverse fault forming the leading edge of the Seattle uplift, a 40-km-wide fold-and-thrust belt. The recently discovered, north-dipping Tacoma reverse fault is interpreted as a back thrust on the trailing edge of the belt, making the belt doubly vergent. Floor thrusts in the Seattle and Tacoma fault zones, imaged as discontinuous reflections, are interpreted as blind faults that flatten updip into bedding plane thrusts. Shallow monoclines in both the Seattle and Tacoma basins are interpreted to overlie the leading edges of thrust-bounded wedge tips advancing into the basins. Across the Seattle uplift, seismic lines image several shallow, short-wavelength folds exhibiting Quaternary or late Quaternary growth. From reflector truncation, several north-dipping thrust faults (splay thrusts) are inferred to core these shallow folds and to splay upward from a shallow roof thrust. Some of these shallow splay thrusts ruptured to the surface in the late Holocene. Ages from offset soils in trenches across the fault scarps and from abruptly raised shorelines indicate that the splay, roof, and floor thrusts of the Seattle and Tacoma faults ruptured about 1100 years ago.

New insights into Late Quaternary slip rate of the thrust fault zone, northern margin of the Qilian Shan, NE Tibet

NASA Astrophysics Data System (ADS)

Hai-bo, Y.; Yang, X., Sr.; LI, A.; Huang, X.; Huang, W.

2017-12-01

The India-Eurasian plate collision caused widespread Cenozoic crustal deformation within the Tibetan Plateau and on its margins. Ongoing post-collisional convergence formed multi-row NWW-trending folded mountain ranges and basins pattern in the northeastern Tibet. Late Quaternary tectonic deformation and quantitative slip rate estimates around the Qilian Shan and the Hexi corridor foreland basin are critical to understanding crustal deformation process of the Tibetan plateau and assessing regional seismic hazards. The Fodongmo-Hongyazi fault (FHF) is a major thrust at the Northeastern Tibet, bounding the Qilian Shan. It is accommodating the crustal shortening across this region and has produced strong historical earthquake. Until now the slip rate has been poorly constrained limiting our understanding of its role in the accommodation of deformation across this region. In this work, faulted terraces at the Hongshuiba River and Fengle River sites on the western and middle segments of the FHF were mapped with satellite imagery and field observations. Chronological constraints are placed on the ages of displaced river terraces at these sites using terrestrial cosmogenic nuclide (TCN) exposure dating. These ages combined with offsets measured from SPOT 6 DEM's yield average vertical slip rates of 1.3±0.1mm/yr for the western segment since 207 ka and 0.9±0.1 mm/yr since 46 ka for the middle segment. These data suggest that the FHF accommodates 15-20% of the total shortening across the Qilian Shan (5.5-7 mm/yr). In addition, comparisons of our data with published slip rates along the Northern Qilian Thrust Fault Zone show that the fastest tectonic uplift occurs along the western portion of the Northern Qilian Shan. This is consistent with estimates deduced from geomorphology. The western portion of the Qilian Shan is mainly controlled by compressional deformation produced by the northward movement of the Northeastern Tibetan Plateau, while the eastern Qilian Shan is mainly controlled by the eastward extrusion of material along the left-lateral Haiyuan strike-slip Fault.

Borehole Breakout Derived Constraints on Stress Regimes in the Santa Barbara Channel, Offshore Southern California

NASA Astrophysics Data System (ADS)

Pritchard, E. H.; Persaud, P.; Stock, J. M.

2017-12-01

The Santa Barbara Channel is an E-W trending marine basin that serves as the southern extension of the Western Transverse Ranges block. Several active, E-W trending en echelon fault systems exist beneath the Channel with both N and S dips. These control a series of tight, asymmetric anticlinal folds along the North Channel and Mid-Channel regions. Although controversial, recent models have suggested that these systems are capable of producing large magnitude, tsunamigenic earthquakes. Not controversial, however, is the fact that further knowledge of the stress regime related to these systems would greatly contribute to our understanding of a potential rupture along them. In this study, oriented 4-arm caliper well log data obtained from industry are used to determine the orientations of stress induced shear failures along well bore walls, called borehole breakouts, beneath two offshore drill platforms in the Santa Barbara Channel. Analysis of breakout orientations along 18 differently oriented, highly deviated wells allows for constraint of the current in situ stress regime beneath each of the platforms. The best-fit stress regime can then be used to inform the nature of slip along nearby faults, many of which are blind and display no surface indications of slip. At the Holly platform, located roughly 19 km west of Santa Barbara, and proximate to the Pitas Point, North Channel, and Red Mountain fault systems, lower hemisphere polar projections of breakout orientations in deviated well sections indicate a mainly thrust faulting stress regime, although a strike-slip component is not currently excluded. At the Gail platform, located midway between Ventura and Santa Cruz Island, and proximate to the Western Deep Fault, polar projections of breakouts indicate that a predominantly thrust faulting stress regime also exists beneath this platform. However, a few inconsistencies in the breakout orientations at each platform suggest variability in the stress regime, leading to the hypothesis that the stress field beneath these regions may change with depth, from a shallow degenerate-like thrust faulting stress state, with the horizontal principal stresses roughly equal in magnitude yet greater than the vertical principal stress (SH = Sh > Sv), to a deeper, less degenerate regime.

Along-strike variations of the partitioning of convergence across the Haiyuan fault system detected by InSAR

NASA Astrophysics Data System (ADS)

Daout, S.; Jolivet, R.; Lasserre, C.; Doin, M.-P.; Barbot, S.; Tapponnier, P.; Peltzer, G.; Socquet, A.; Sun, J.

2016-04-01

Oblique convergence across Tibet leads to slip partitioning with the coexistence of strike-slip, normal and thrust motion on major fault systems. A key point is to understand and model how faults interact and accumulate strain at depth. Here, we extract ground deformation across the Haiyuan Fault restraining bend, at the northeastern boundary of the Tibetan plateau, from Envisat radar data spanning the 2001-2011 period. We show that the complexity of the surface displacement field can be explained by the partitioning of a uniform deep-seated convergence. Mountains and sand dunes in the study area make the radar data processing challenging and require the latest developments in processing procedures for Synthetic Aperture Radar interferometry. The processing strategy is based on a small baseline approach. Before unwrapping, we correct for atmospheric phase delays from global atmospheric models and digital elevation model errors. A series of filtering steps is applied to improve the signal-to-noise ratio across high ranges of the Tibetan plateau and the phase unwrapping capability across the fault, required for reliable estimate of fault movement. We then jointly invert our InSAR time-series together with published GPS displacements to test a proposed long-term slip-partitioning model between the Haiyuan and Gulang left-lateral Faults and the Qilian Shan thrusts. We explore the geometry of the fault system at depth and associated slip rates using a Bayesian approach and test the consistency of present-day geodetic surface displacements with a long-term tectonic model. We determine a uniform convergence rate of 10 [8.6-11.5] mm yr-1 with an N89 [81-97]°E across the whole fault system, with a variable partitioning west and east of a major extensional fault-jog (the Tianzhu pull-apart basin). Our 2-D model of two profiles perpendicular to the fault system gives a quantitative understanding of how crustal deformation is accommodated by the various branches of this thrust/strike-slip fault system and demonstrates how the geometry of the Haiyuan fault system controls the partitioning of the deep secular motion.

Kinematic development of the Tibetan Plateau's northern margin: A traverse across the Qilian Shan-Nan Shan thrust belt

NASA Astrophysics Data System (ADS)

Zuza, A. V.; Levy, D. A.; Wang, Z.; Xiong, X.; Chen, X.

2017-12-01

The active Cenozoic Qilian Shan-Nan Shan thrust belt defines the northern margin of the Tibetan Plateau. The kinematic development of this thrust belt has implications models of plateau growth and Himalayan-Tibetan orogen strain accommodation. We present new field observations and analytical data from a traverse across the 350-km-wide doubly vergent Qilian Shan, which is bound by the south-dipping North Qilian thrust system in the north and the north-dipping range-bounding Qinghai Nanshan-Dulan Shan thrust system in the south. These faults, and several other major thrusts within the thrust-belt interior, disrupt relatively thick Oligocene-Miocene basin deposits. Of note, many of the thrust faults across the width of the Qilian Shan have Quaternary fault scarps, indicating that active deformation is distributed and not only concentrated along the northern frontal faults. By integrating our detailed structural traverse with new geophysical observations and thermochronology data across the northern plateau margin, we construct a kinematic model for the development of the Tibetan Plateau's northern margin. Deformation initiated in the Eocene-Oligocene along the north-dipping Qinghai Nanshan-Dulan Shan and south-dipping Tuolai Nan Shan thrusts, the latter of which then defined the northern boundary of the Tibetan Plateau. This early deformation was focused along preexisting early Paleozoic structures. A 200-km-wide basin formed between these ranges, and from the Miocene to present, new thrust- and strike-slip-fault-bounded ranges developed, including the north-directed North Qilian and the south-directed Tuolai Nan thrusts. Thus, our observations do not support northward propagating thrust-belt expansion. Instead, we envision that the initial thrust-belt development generated a wide Oligocene-Miocene north-plateau basin that was subsequently disintegrated by later Miocene to present thrusting and strike-slip faulting. Ultimately, the Qilian Shan-Nan Shan thrust belt differs from a typical orogenic thrust wedge, and active deformation is distributed across the range.

Pliocene episodic exhumation and the significance of the Munsiari thrust in the northwestern Himalaya

NASA Astrophysics Data System (ADS)

Stübner, Konstanze; Grujic, Djordje; Dunkl, István; Thiede, Rasmus; Eugster, Patricia

2018-01-01

The Himalayan thrust belt comprises three in-sequence foreland-propagating orogen-scale faults, the Main Central thrust, the Main Boundary thrust, and the Main Frontal thrust. Recently, the Munsiari-Ramgarh-Shumar thrust system has been recognized as an additional, potentially orogen-scale shear zone in the proximal footwall of the Main Central thrust. The timing of the Munsiari, Ramgarh, and Shumar thrusts and their role in Himalayan tectonics are disputed. We present 31 new zircon (U-Th)/He ages from a profile across the central Himachal Himalaya in the Beas River area. Within a ∼40 km wide belt northeast of the Kullu-Larji-Rampur window, ages ranging from 2.4 ± 0.4 Ma to 5.4 ± 0.9 Ma constrain a distinct episode of rapid Pliocene to Present exhumation; north and south of this belt, zircon (U-Th)/He ages are older (7.0 ± 0.7 Ma to 42.2 ± 2.1 Ma). We attribute the Pliocene rapid exhumation episode to basal accretion to the Himalayan thrust belt and duplex formation in the Lesser Himalayan sequence including initiation of the Munsiari thrust. Pecube thermokinematic modelling suggests exhumation rates of ∼2-3 mm/yr from 4-7 to 0 Ma above the duplex contrasting with lower (<0.3 mm/yr) middle-late Miocene exhumation rates. The Munsiari thrust terminates laterally in central Himachal Pradesh. In the NW Indian Himalaya, the Main Central thrust zone comprises the sheared basal sections of the Greater Himalayan sequence and the mylonitic 'Bajaura nappe' of Lesser Himalayan affinity. We correlate the Bajaura unit with the Ramgarh thrust sheet in Nepal based on similar lithologies and the middle Miocene age of deformation. The Munsiari thrust in the central Himachal Himalaya is several Myr younger than deformation in the Bajaura and Ramgarh thrust sheets. Our results illustrate the complex and segmented nature of the Munsiari-Ramgarh-Shumar thrust system.

Evidence for ongoing extensional deformation in the western Swiss Alps and thrust-faulting in the southwestern Alpine foreland

NASA Astrophysics Data System (ADS)

Eva, Elena; Pastore, Stefania; Deichmann, Nicholas

1998-09-01

To verify the discordant orientations of P- and T-axes found by earlier studies in the Penninic domain of the southern Valais, Switzerland, and in the surrounding regions of France and Italy, we have evaluated the focal mechanisms of 11 of the best-recorded earthquakes that occurred in this area between 1985 and 1990. By employing two-dimensional ray-tracing techniques, we have made use of what is known about the lateral variations of the crustal structure to obtain constraints on the possible focal-depth range of the hypocenters and on the take-off angles at the source. In addition, we have been able to identify one of the two nodal planes as the actual fault plane of one of the events, based on high-resolution relative locations of its aftershocks. The resulting normal faulting and oblique-slip focal mechanisms show that, down to depths of about 10 km, the compressional structures of the Penninic nappes, which were formed during the Alpine orogeny, are presently undergoing extensional deformation and that a significant component of this extension is perpendicular to the Alpine arc. Thrust faulting focal mechanisms from events at the northwestern margin of the Po plain, however, indicate that the southern Alpine foreland is still subject to compressional deformation consistent with the large-scale stress field expected from the convergence of the African and European plates. Thus, our results lend support to geodynamic models that predict extensional deformation across the crest of a mountain range, while the flanks and lowlands continue to undergo crustal shortening.

Lithofacies and stratigraphy of the Lisburne and Etivluk groups in the Lisburne 1 well and adjacent outcrops

USGS Publications Warehouse

Dumoulin, Julie A.; Bird, Kenneth J.

2002-01-01

The Lisburne 1 well in the thrust belt of the central Brooks Range penetrated 17,000 ft of imbricated, chiefly Ellesmerian sequence strata in the Endicott Mountains allochthon. Five thrust repeats of the Lisburne Group (Carboniferous) and overlying Etivluk Group (Permian-Jurassic) were drilled. Lithofacies analyses of >350 thin sections of cores and cuttings, and biostratigraphy based on foraminifers and conodonts, allow detailed correlation with coeval units in adjacent outcrops and provide data on the depositional setting and reservoir and source rock potential of these strata. The late Early- Late Mississippian (Osagean-Chesterian) Lisburne Group consists mainly of skeletal wackestone to grainstone, locally completely dolomitized. An interval of abundant glauconite and detrital quartz in the lower Lisburne may mark a sequence-bounding unconformity. Dolostone in the upper part of the unit has maximum porosities of 10-13% and common residual hydrocarbons. The uppermost Lisburne is thinly interbedded mudstone, chert, and shale that are locally dolomitic, phosphatic, spiculitic, and organic-rich; conodonts from this interval in outcrop represent an outer shelf to slope biofacies. The Etivluk Group here encompasses the Siksikpuk and Otuk Formations. The Siksikpuk is mainly varicolored shale and radiolarian chert, with a basal interval of glauconitic, pyritic sandstone. Phosphatic and organic-rich shale, radiolarian chert, and pelecypod coquinas make up the Otuk. Outcrop and subsurface data indicate that the Lisburne Group in this area accumulated near the seaward margin of a shallow-water carbonate platform that drowned during the Late Mississippian; outer shelf or deeper conditions predominated throughout deposition of the upper Lisburne and the Etivluk Group.

Kinematics, Exhumation, and Sedimentation of the North Central Andes (Bolivia): An Integrated Thermochronometer and Thermokinematic Modeling Approach

NASA Astrophysics Data System (ADS)

Rak, Adam J.; McQuarrie, Nadine; Ehlers, Todd A.

2017-11-01

Quantifying mountain building processes in convergent orogens requires determination of the timing and rate of deformation in the overriding plate. In the central Andes, large discrepancies in both timing and rate of deformation prevent evaluating the shortening history in light of internal or external forcing factors. Geologic map patterns, age and location of reset thermochronometer systems, and synorogenic sediment distribution are all a function of the geometry, kinematics, and rate of deformation in a fold-thrust-belt-foreland basin (FTB-FB) system. To determine the timing and rate of deformation in the northern Bolivian Andes, we link thermokinematic modeling to a sequentially forward modeled, balanced cross section isostatically accounting for thrust loads and erosion. Displacement vectors, in 10 km increments, are assigned variable ages to create velocity fields in a thermokinematic model for predicting thermochronometer ages. We match both the pattern of predicted cooling ages with the across strike pattern of measured zircon fission track, apatite fission track, and apatite (U-Th)/He cooling ages as well as the modeled age of FB formations to published sedimentary sections. Results indicate that northern Bolivian FTB deformation started at 50 Ma and may have begun as early as 55 Ma. Acceptable rates of shortening permit either a constant rate of shortening ( 4-5 mm/yr) or varying shortening rates with faster rates (7-10 mm/yr) at 45-50 Ma and 12-8 Ma, significantly slower rates (2-4 mm/yr) from 35 to 15 Ma and indicate the northern Bolivian Subandes started deforming between 19 and 14 Ma.

Summary of the Ahankashan Area of Interest

USGS Publications Warehouse

Drew, Lawrence J.; Sutphin, David M.; Mars, John C.; Bogdanow, Anya K.

2015-09-15

This report summarizes and interprets results of the work in the Ahankashan Area of Interest in northwestern Afghanistan and four study areas—the Ahankashan Prospect Area, Syahsang-Kushkak, Taghab-Soni, and Zakak-e ‘Olya—delineated for their potential undiscovered mineral occurrences with specific emphasis on porphyry copper and related occurrence types. The Area of Interest is underlain by rocks of three different geologic domains that cross from east to west—the Band-e-Bayan Block/Central Pamirs Domain in the south, the Hindu Kush Domain in the Paropamisus Mountains, and the Afghan Turkestan Domain in the north. The domains are sutured remnants of Tethyan tectonic elements. Interpretation of the geologic maps indicates the presence of thrust faults, strike-slip faults, and granitic intrusions emplaced in ground prepared by faulting. Thrust faulting was followed by strike-slip faulting and then followed by magmatic intrusions. Advanced Spaceborne Thermal Emission and Reflection Radiometer data were used to map minerals that have been altered by hydrothermal fluids typically associated with mineralization to delineate new potential occurrences of copper, gold, and silver. Propylitic-, argillic-, and phyllic-altered intrusive rocks are found in the area, as well as very minor amounts of hydrothermal silica-rich rocks. This area of interest is vastly underexplored and contains only seven known mineral occurrences, of which the Ahankashan copper (gold) skarn occurrence is the best known. Gold has been found in stream sediments near the Ahankashan skarn, in the Taghab-Soni study area, and possibly other parts of the Area of Interest, suggesting potential for at least small-scale placer occurrences.

pp iii Morphological response to Quaternary deformation at an intermontane basin piedmont, the northern Tien Shan, Kyrghyzstan

NASA Astrophysics Data System (ADS)

Bowman, Dan; Korjenkov, Andrey; Porat, Naomi; Czassny, Birka

2004-11-01

The Tien Shan is a most active intracontinental mountain-building range with abundant Quaternary fault-related folding. In order to improve our understanding of Quaternary intermontane basin deformation, we investigated the intermontane Issyk-Kul Lake area, an anticline that was up-warped through the piedmont cover, causing partitioning of the alluvial fan veneer. To follow the morphological scenario during the warping process, we relied on surface-exposed and trenched structures and on alluvial fans and bajadas as reference surfaces. We used air photos and satellite images to analyze the spatial-temporal morphological record and determined the age of near surface sediments by luminescence dating. We demonstrate that the up-warped Ak-Teke hills are a thrust-generated subdued anticline with strong morphological asymmetry which results from the coupling of the competing processes of up-warp and erosional feedback. The active creeks across the up-warped anticline indicate that the antecedent drainage system kept pace with the rate of uplift. The rivers which once sourced the piedmont, like the Toru-Aygyr, Kultor and the Dyuresu, became deeply entrenched and gradually transformed the study area into an abandoned morphological surface. The up-warp caused local lateral drainage diversion in front of the northern backlimb and triggered the formation of a dendritic drainage pattern upfan. Luminescence dating suggest that the period of up-warp and antecedent entrenchment started after 157 ka. The morphologically mature study area demonstrates the response of fluvial systems to growing folds on piedmont areas, induced by a propagating frontal fold at a thrust belt edge, following shortening.

Frequency Domain Full-Waveform Inversion in Imaging Thrust Related Features

NASA Astrophysics Data System (ADS)

Jaiswal, P.; Zelt, C. A.

2010-12-01

Seismic acquisition in rough terrain such as mountain belts suffers from problems related to near-surface conditions such as statics, inconsistent energy penetration, rapid decay of signal, and imperfect receiver coupling. Moreover in the presence of weakly compacted soil, strong ground roll may obscure the reflection arrivals at near offsets further diminishing the scope of estimating a reliable near surface image though conventional processing. Traveltime and waveform inversion not only overcome the simplistic assumptions inherent in conventional processing such as hyperbolic moveout and convolution model, but also use parts of the seismic coda, such as the direct arrival and refractions, that are discarded in the latter. Traveltime and waveform inversion are model-based methods that honour the physics of wave propagation. Given the right set of preconditioned data and starting model, waveform inversion in particular has been realized as a powerful tool for velocity model building. This paper examines two case studies on waveform inversion using real data from the Naga Thrust Belt in the Northeast India. Waveform inversion in this paper is performed in the frequency domain and is multiscale in nature i.e., the inversion progressively ascends from the lower to the higher end of the frequency spectra increasing the wavenumber content of the recovered model. Since the real data are band limited, the success of waveform inversion depends on how well the starting model can account for the missing low wavenumbers. In this paper it is observed that the required starting model can be prepared using the regularized inversion of direct and reflected arrival times.

The nature of orogenic crust in the central Andes

NASA Astrophysics Data System (ADS)

Beck, Susan L.; Zandt, George

2002-10-01

The central Andes (16°-22°S) are part of an active continental margin mountain belt and the result of shortening of the weak western edge of South America between the strong lithospheres of the subducting Nazca plate and the underthrusting Brazilian shield. We have combined receiver function and surface wave dispersion results from the BANJO-SEDA project with other geophysical studies to characterize the nature of the continental crust and mantle lithospheric structure. The major results are as follows: (1) The crust supporting the high elevations is thick and has a felsic to intermediate bulk composition. (2) The relatively strong Brazilian lithosphere is underthrusting as far west (65.5°W) as the high elevations of the western part of the Eastern Cordillera (EC) but does not underthrust the entire Altiplano. (3) The subcrustal lithosphere is delaminating piecemeal under the Altiplano-EC boundary but is not completely removed beneath the central Altiplano. The Altiplano crust is characterized by a brittle upper crust decoupled from a very weak lower crust that is dominated by ductile deformation, leading to lower crustal flow and flat topography. In contrast, in the high-relief, inland-sloping regions of the EC and sub-Andean zone, the upper crust is still strongly coupled across the basal thrust of the fold-thrust belt to the underthrusting Brazilian Shield lithosphere. Subcrustal shortening between the Altiplano and Brazilian lithosphere appears to be accommodated by delamination near the Altiplano-EC boundary. Our study suggests that orogenic reworking may be an important part of the "felsification" of continental crust.

Complex thrusting at the toe of the Nankai accretionary prism, NanTroSEIZE Kumano transect

NASA Astrophysics Data System (ADS)

Moore, G. F.; Park, J.; Kodaira, S.; Kaneda, Y.

2009-12-01

Seismic reflection data collected over the past 10 years by the Institute for Research on Earth Evolution (IFREE) of Japan Agency for Marine Earth Science and Technology (JAMSTEC) image a zone of complex thrusting at the toe of the Nankai accretionary prism south of Kii Peninsula, Honshu, Japan. The frontal part of the Nankai prism west of Shionomisaki Canyon (SC) at ~136° E, including the Muroto and Ashizuri Transects off Shikoku, is generally formed of imbricate thrusts with spacing of ~ 1-3 km that dip ~25-35° landward and sole into a prominent décollement. Out-of-sequence thrusts (OOSTs) are usually restricted to the landward margin of this imbricate thrust zone. East of SC, in the Kumano Transect area, the imbricate thrust zone is bounded on its seaward edge by a frontal thrust block that is ~5-6 km wide and consists of several OOSTs. The frontal thrust dips ~5-10° under this ~2-4 km thick block, emplacing this thrust sheet over the trench floor. The number and character of thrusts within the frontal thrust block vary laterally along strike. The 2006 Kumano 3D seismic data set images details of one segment of this complex frontal thrust block. Out-of-sequence faulting has led to underplating of several smaller thrust slices and movement along oblique ramps has led to a complex pattern of faulting that cannot be recognized in even closely-spaced 2D seismic lines. The frontal thrust block is further modified by subduction of seamounts and ridges that have caused large slumps of material from the block.

Fluid lubricated bearing assembly

DOEpatents

Boorse, Henry A.; Boeker, Gilbert F.; Menke, John R.

1976-01-01

1. A support for a loaded rotatable shaft comprising in combination on a housing having a fluid-tight cavity encasing an end portion of said shaft, a thrust bearing near the open end of said cavity for supporting the axial thrust of said shaft, said thrust bearing comprising a thrust plate mounted in said housing and a thrust collar mounted on said shaft, said thrust plate having a central opening the peripheral portion of which is hermetically sealed to said housing at the open end of said cavity, and means for supplying a fluid lubricant to said thrust bearing, said thrust bearing having a lubricant-conducting path connecting said lubricant supplying means with the space between said thrust plate and collar intermediate the peripheries thereof, the surfaces of said plate and collar being constructed and arranged to inhibit radial flow of lubricant and, on rotation of said thrust collar, to draw lubricant through said path between the bearing surfaces and to increase the pressure therebetween and in said cavity and thereby exert a supporting force on said end portion of said shaft.

Development of a two-dimensional dual pendulum thrust stand for Hall thrusters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nagao, N.; Yokota, S.; Komurasaki, K.

A two-dimensional dual pendulum thrust stand was developed to measure thrust vectors (axial and horizontal (transverse) direction thrusts) of a Hall thruster. A thruster with a steering mechanism is mounted on the inner pendulum, and thrust is measured from the displacement between inner and outer pendulums, by which a thermal drift effect is canceled out. Two crossover knife-edges support each pendulum arm: one is set on the other at a right angle. They enable the pendulums to swing in two directions. Thrust calibration using a pulley and weight system showed that the measurement errors were less than 0.25 mN (1.4%)more » in the main thrust direction and 0.09 mN (1.4%) in its transverse direction. The thrust angle of the thrust vector was measured with the stand using the thruster. Consequently, a vector deviation from the main thrust direction of {+-}2.3 deg. was measured with the error of {+-}0.2 deg. under the typical operating conditions for the thruster.« less

Nanonewton thrust measurement of photon pressure propulsion using semiconductor laser

NASA Astrophysics Data System (ADS)

Iwami, K.; Akazawa, Taku; Ohtsuka, Tomohiro; Nishida, Hiroyuki; Umeda, Norihiro

2011-09-01

To evaluate the thrust produced by photon pressure emitted from a 100 W class continuous-wave semiconductor laser, a torsion-balance precise thrust stand is designed and tested. Photon emission propulsion using semiconductor light sources attract interests as a possible candidate for deep-space propellant-less propulsion and attitude control system. However, the thrust produced by photon emission as large as several ten nanonewtons requires precise thrust stand. A resonant method is adopted to enhance the sensitivity of the biflier torsional-spring thrust stand. The torsional spring constant and the resonant of the stand is 1.245 × 10-3 Nm/rad and 0.118 Hz, respectively. The experimental results showed good agreement with the theoretical estimation. The thrust efficiency for photon propulsion was also defined. A maximum thrust of 499 nN was produced by the laser with 208 W input power (75 W of optical output) corresponding to a thrust efficiency of 36.7%. The minimum detectable thrust of the stand was estimated to be 2.62 nN under oscillation at a frequency close to resonance.

Tsien's method for generating non-Keplerian trajectories. Part 2: The question of thrust to orbit a sphere and the restricted three-body problem

NASA Technical Reports Server (NTRS)

Murad, P. A.

1993-01-01

Tsien's method is extended to treat the orbital motion of a body undergoing accelerations and decelerations. A generalized solution is discussed for the generalized case where a body undergoes azimuthal and radial thrust and the problem is further simplified for azimuthal thrust alone. Judicious selection of thrust could generate either an elliptic or hyperbolic trajectory. This is unexpected especially when the body has only enough energy for a lower state trajectory. The methodology is extended treating the problem of vehicle thrust for orbiting a sphere and vehicle thrust within the classical restricted three-body problem. Results for the latter situation can produce hyperbolic trajectories through eigen value decomposition. Since eigen values for no-thrust can be imaginary, thrust can generate real eigen values to describe hyperbolic trajectories. Keplerian dynamics appears to represent but a small subset of a much larger non-Keplerian domain especially when thrust effects are considered. The need for high thrust long duration space-based propulsion systems for changing a trajectory's canonical form is clearly demonstrated.

Microstructures and strain variation: Evidence of multiple splays in the North Almora Thrust Zone, Kumaun Lesser Himalaya, Uttarakhand, India

NASA Astrophysics Data System (ADS)

Joshi, Gaurav; Agarwal, Amar; Agarwal, K. K.; Srivastava, Samriddhi; Alva Valdivia, L. M.

2017-01-01

The North Almora Thrust zone (NATZ) marks the boundary of the Almora Crystalline Complex (ACC) against the Lesser Himalayan Sedimentary sequence (LHS) in the north. Its southern counterpart, the South Almora Thrust (SAT), is a sharply marked contact between the ACC and the LHS in the south. Published studies argue various contradictory emplacement modes of the North Almora Thrust. Recent studies have implied splays of smaller back thrusts in the NATZ. The present study investigates meso- and microstructures, and strain distribution in the NATZ and compares it with strain distribution across the SAT. In the NATZ, field evidence reveals repeated sequence of 10-500 m thick slices of proto- to ultra-mylonite, thrust over the Lesser Himalayan Rautgara quartzite. In accordance with the field evidence, the strain analysis reveals effects of splays of smaller thrust in the NATZ. The study therefore, argues that contrary to popular nomenclature the northern contact of the ACC with the LHS is not a single thrust plane, but a thrust zone marked by numerous thrust splays.

Attitude Control for an Aero-Vehicle Using Vector Thrusting and Variable Speed Control Moment Gyros

NASA Technical Reports Server (NTRS)

Shin, Jong-Yeob; Lim, K. B.; Moerder, D. D.

2005-01-01

Stabilization of passively unstable thrust-levitated vehicles can require significant control inputs. Although thrust vectoring is a straightforward choice for realizing these inputs, this may lead to difficulties discussed in the paper. This paper examines supplementing thrust vectoring with Variable-Speed Control Moment Gyroscopes (VSCMGs). The paper describes how to allocate VSCMGs and the vectored thrust mechanism for attitude stabilization in frequency domain and also shows trade-off between vectored thrust and VSCMGs. Using an H2 control synthesis methodology in LMI optimization, a feedback control law is designed for a thrust-levitated research vehicle and is simulated with the full nonlinear model. It is demonstrated that VSCMGs can reduce the use of vectored thrust variation for stabilizing the hovering platform in the presence of strong wind gusts.

Evaluation of an Outer Loop Retrofit Architecture for Intelligent Turbofan Engine Thrust Control

NASA Technical Reports Server (NTRS)

Litt, Jonathan S.; Sowers, T. Shane

2006-01-01

The thrust control capability of a retrofit architecture for intelligent turbofan engine control and diagnostics is evaluated. The focus of the study is on the portion of the hierarchical architecture that performs thrust estimation and outer loop thrust control. The inner loop controls fan speed so the outer loop automatically adjusts the engine's fan speed command to maintain thrust at the desired level, based on pilot input, even as the engine deteriorates with use. The thrust estimation accuracy is assessed under nominal and deteriorated conditions at multiple operating points, and the closed loop thrust control performance is studied, all in a complex real-time nonlinear turbofan engine simulation test bed. The estimation capability, thrust response, and robustness to uncertainty in the form of engine degradation are evaluated.

Oligocene-miocene mammalian fossils from Hongyazi Basin and its bearing on tectonics of Danghe Nanshan in northern Tibetan plateau.

PubMed

Li, Qiang; Wang, Xiaoming; Xie, Guangpu; Yin, An

2013-01-01

A shortage of Cenozoic vertebrate fossils in the Tibetan Plateau has been an obstacle in our understanding of biological evolution in response to changes in tectonism, topography, and environment. This is especially true for Paleogene records, so far known by only two sites along the northern rim of the Plateau. We report a Hongyazi Basin in northern Tibetan Plateau that produces at least three mammalian faunas that span Oligocene through late Miocene. Located at the foothills of the Danghe Nanshan and presently connected to the northern margin of the Suganhu Basin through the Greater Haltang River, the intermountain basin is controlled by the tectonics of the Danghe Nanshan to the north and Chahan'ebotu Mountain to the south, making the basin sediments well suited for inferring the evolutionary history of these two mountain ranges. At the bottom of the local section, the Oligocene Haltang Fauna is best compared to the early Oligocene Desmatolagus-Karakoromys decessus assemblage in the Dingdanggou Fauna in Tabenbuluk Basin. The Middle Miocene Ebotu Fauna from the middle Hongyazi section shares many taxa with the late Middle Miocene Tunggur mammal assemblage in Inner Mongolia, such as Heterosminthus orientalis, Megacricetodon sinensis, Democricetodon lindsayi, and Alloptox gobiensis. Toward the top of the section, the Hongyazi Fauna includes late Miocene elements typical of Hipparion faunas of North China. All three faunas are of typical North China-Central Asian characteristics, suggesting a lack of geographic barriers for faunal differentiation through the late Miocene. Sedimentary packages producing these faunas are arrayed from north to south in progressively younger strata, consistent with a compressive regime to accommodate shortening between Danghe Nanshan and Chahan'ebotu Mountain by thrust faults and folds. With additional constraints from vertebrate fossils along the northern flanks of the Danghe Nanshan, an eastward propagation of the Danghe Nanshan is postulated.

Oligocene-Miocene Mammalian Fossils from Hongyazi Basin and Its Bearing on Tectonics of Danghe Nanshan in Northern Tibetan Plateau

PubMed Central

Li, Qiang; Wang, Xiaoming; Xie, Guangpu; Yin, An

2013-01-01

A shortage of Cenozoic vertebrate fossils in the Tibetan Plateau has been an obstacle in our understanding of biological evolution in response to changes in tectonism, topography, and environment. This is especially true for Paleogene records, so far known by only two sites along the northern rim of the Plateau. We report a Hongyazi Basin in northern Tibetan Plateau that produces at least three mammalian faunas that span Oligocene through late Miocene. Located at the foothills of the Danghe Nanshan and presently connected to the northern margin of the Suganhu Basin through the Greater Haltang River, the intermountain basin is controlled by the tectonics of the Danghe Nanshan to the north and Chahan’ebotu Mountain to the south, making the basin sediments well suited for inferring the evolutionary history of these two mountain ranges. At the bottom of the local section, the Oligocene Haltang Fauna is best compared to the early Oligocene Desmatolagus-Karakoromys decessus assemblage in the Dingdanggou Fauna in Tabenbuluk Basin. The Middle Miocene Ebotu Fauna from the middle Hongyazi section shares many taxa with the late Middle Miocene Tunggur mammal assemblage in Inner Mongolia, such as Heterosminthus orientalis, Megacricetodon sinensis, Democricetodon lindsayi, and Alloptox gobiensis. Toward the top of the section, the Hongyazi Fauna includes late Miocene elements typical of Hipparion faunas of North China. All three faunas are of typical North China-Central Asian characteristics, suggesting a lack of geographic barriers for faunal differentiation through the late Miocene. Sedimentary packages producing these faunas are arrayed from north to south in progressively younger strata, consistent with a compressive regime to accommodate shortening between Danghe Nanshan and Chahan’ebotu Mountain by thrust faults and folds. With additional constraints from vertebrate fossils along the northern flanks of the Danghe Nanshan, an eastward propagation of the Danghe Nanshan is postulated. PMID:24376585

Growth and gravitational collapse of a mountain front of the Eastern Cordillera of Colombia

NASA Astrophysics Data System (ADS)

Kammer, Andreas; Montana, Jorge; Piraquive, Alejandro

2016-04-01

The Eastern Cordillera of Colombia is bracketed between the moderately east-dipping flank of the Central Cordillera on its western and the gently bent Guayana shield on its eastern side. It evolved as a response to a considerable displacement transfer from the Nazca to the Southamerican plate since the Oligocene break-up of the Farallon plate. One of its distinctive traits refers to its significant shortening by penetrative strain at lower and folding at higher structural levels, approximating a wholesale pure-shear in analogy to a vice model or a crustal welt sandwiched between rigid buttresses. This contrasting behavior may be explained by the spatial coincidence between Neogene mountain belt and a forebulge that shaped the foreland trough during a Cretaceous subduction cycle and was very effective in localizing a weakening of the backarc region comprised between two basin margin faults. In this paper we examine a two-phase evolution of the Eastern mountain front. Up to the late Miocene deformation was restrained by the inherited eastern basin margin fault and as the cordilleran crust extruded, a deformation front with an amplitude similar the present structural relief of up to 10.000 m may have built up. In the Pliocene convergence changed from a roughly strike-perpendicular to an oblique E-W direction and caused N-S trending faults to branch off from the deformation front. This shortening was partly driven by a gravitational collapse of the Miocene deformation front, that became fragmented by normal faults and extruded E on newly formed Pliocene thrust faults. Normal faults display displacements of up to 3000 m and channelized hydrothermal fluids, leading to the formation of widely distributed fault breccias and giving rise to a prolific Emerald mineralization. In terms of wedge dynamics, the Pliocene breaching of the early formed deformation front helped to establish a critical taper.

Linking Late Miocene Magmatism and Exhumation of the Pamir-West Kunlun Mountains to Lithospheric Thinning

NASA Astrophysics Data System (ADS)

Cao, K.; Wang, G.; Zeng, Z.; Replumaz, A.

2016-12-01

In this study, we report newly-discovered potassic plutons emplaced at 11 Ma in the SE Pamir. Together with recently-reported volcanism at 12 Ma in the West Kunlun Mts. (Cao et al., 2015), it can be inferred that Late Miocene magmas extend from the north-central Tibet to the central Pamir. Furthermore, our new apatite fission-track analysis in the SE Pamir-West Kunlun Mountains present uniform ages clustering at 11-6 Ma. Forward and inverse modeling indicate Late Miocene ( 11-6 Ma) rapid exhumation of the SE Pamir-West Kunlun Mountains, concurrent with accelerated exhumation of the Shakhdara dome (Stübner et al., 2013), initial doming of the Muztagata massif (Robinson et al., 2007; Sobel et al., 2011; Cao et al., 2013), and thrusting of the front faults along Pamir-West Kunlun Mts. (Bershaw et al., 2012; Cao et al., 2013, 2015). The simultaneous doming and potassic magmatism could attributed to stress relaxation of the upper crust at that time, possibly driven by the thinning of lower lithosphere beneath Pamir-West Kunlun Mts.. Such plausible mechanisms could be responsible for Neogene magmatism, rock exhumation and plateau growth in northwestern Tibet. At the continental scale, our results support that the Tibetan Plateau underwent a Late Miocene phase of deformation and developed outward and upward since then (Molnar et al., 2012). Three representative models are proposed to account for Late Miocene magmatism and crustal deformation in northern Tibet, including 1) southward subduction of the Tarim lithosphere mantle (Matte et al., 1996; Wittlinger et al., 2004), 2) convective removal of lower lithosphere (Molnar et al., 1993; Turner et al., 1993, 1996), and 3) penetration of molten crust into Kunlun terrane (Le Pape et al., 2012; Wang et al., 2012). Our results allow to discuss these competing models in the western Tibet, to better understand the intracontinent orogenesis in central Asia, in which the lithospheric processes have led to upper crust deformation.

Nucleation of Waterfalls at Fault Scarps Temporarily Shielded By Alluvial Fan Aggradation.

NASA Astrophysics Data System (ADS)

Malatesta, L. C.; Lamb, M. P.

2014-12-01

Waterfalls are important components of mountain river systems and they can serve as an agent to transfer tectonic, climatic, or authigenic signals upstream through a catchment. Retreating waterfalls lower the local base level of the adjacent hillslopes, and temporarily increase sediment delivery to the fluvial system. Their creation is often attributed to seismic ruptures, lithological boundaries, or the coalescence of multiple smaller steps. We explore here a mechanism for the nucleation of waterfalls that does not rely on sudden seismic slip but on the build-up of accumulated slip during periods of fault burial by fluvial aggradation. Alluvial fans are common features at the front of mountain ranges bound by normal or thrust faults. Climate change or internal forcing in the mountain catchment modifies the equilibrium slope of alluvial fans. When alluvial fans aggrade, they shield the active fault scarp from fluvial erosion allowing the scarp to grow undisturbed. The scarp may then be exposed when the channel incises into the fan exposing a new bedrock waterfall. We explore this mechanism analytically and using a numerical model for bedrock river incision and sediment deposition. We find that the creation of waterfalls by scarp burial is limited by three distinct timescales: 1) the critical timescale for the scarp to grow to the burial height, 2) the timescale of alluvial re-grading of the fan, and 3) the timescale of the external or internal forcing, such as climate change. The height of the waterfall is controlled by i) the difference in equilibrium alluvial-fan slopes, ii) the ratio of the respective fan and catchment sizes, iii) the catchment wide denudation rate, and iv) the fault slip rate. We test whether an individual waterfall could be produced by alluvial shielding of a scarp, and identify the tectonic, climatic, or authigenic nature of waterfalls using example field sites in the southwest United States.

The Bear River Fault Zone, Wyoming and Utah: Complex Ruptures on a Young Normal Fault

NASA Astrophysics Data System (ADS)

Schwartz, D. P.; Hecker, S.; Haproff, P.; Beukelman, G.; Erickson, B.

2012-12-01

The Bear River fault zone (BRFZ), a set of normal fault scarps located in the Rocky Mountains at the eastern margin of Basin and Range extension, is a rare example of a nascent surface-rupturing fault. Paleoseismic investigations (West, 1994; this study) indicate that the entire neotectonic history of the BRFZ may consist of two large surface-faulting events in the late Holocene. We have estimated a maximum per-event vertical displacement of 6-6.5 m at the south end of the fault where it abuts the north flank of the east-west-trending Uinta Mountains. However, large hanging-wall depressions resulting from back rotation, which front scarps that locally exceed 15 m in height, are prevalent along the main trace, obscuring the net displacement and its along-strike distribution. The modest length (~35 km) of the BRFZ indicates ruptures with a large displacement-to-length ratio, which implies earthquakes with a high static stress drop. The BRFZ is one of several immature (low cumulative displacement) normal faults in the Rocky Mountain region that appear to produce high-stress drop earthquakes. West (1992) interpreted the BRFZ as an extensionally reactivated ramp of the late Cretaceous-early Tertiary Hogsback thrust. LiDAR data on the southern section of the fault and Google Earth imagery show that these young ruptures are more extensive than currently mapped, with newly identified large (>10m) antithetic scarps and footwall graben. The scarps of the BRFZ extend across a 2.5-5.0 km-wide zone, making this the widest and most complex Holocene surface rupture in the Intermountain West. The broad distribution of Late Holocene scarps is consistent with reactivation of shallow bedrock structures but the overall geometry of the BRFZ at depth and its extent into the seismogenic zone are uncertain.

Deep Landslides in flysch formations

NASA Astrophysics Data System (ADS)

Marinos, Vassilis

2017-04-01

Flysch, linked with the tectonic development of an area, has suffered from compressional forces being highly deformed by thrust faults and folds, containing thus often tectonically pre-sheared zones of various size. These geological characteristics may produce weak to very weak rock masses which may present instability and landslides in both mountain and local slope scale. The paper mainly discusses the "mountain" scale phenomena. The size of these masses can reach hundreds of meters in both depth and width on the valley sides. A brief presentation of the flysch formation is presented. A typology is presented with 11 types of flysch, depending on the persistence and participation or not of the strong members (as sandstones) against the weak ones (as siltstones, shales) and the degree and scale of tectonic disturbance. These rock mass types are connected with the landslide mechanism. In all cases the tectonic conditions of a broader area are responsible and the establishment of the tectonic-paleogeographic model is necessary before the conceptual study and design of any major infrastructure work and the choice of its alignment or location. Given the size of such instability areas remedial measures are in most cases not feasible and the realignment or relocation from the initial plans are often the only solution. Cases from highways and pipelines in Greek and Albanian territory are presented. A large number of information from lab tests, geotechnical classifications and back analyses collected from a wide variety of flysch formations is presented and discussed.

Geology of 1. 7 GA ( ) Baldwin gneiss in the Baldwin Lake type area, San Bernardino Mountains, southern California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barth, A.P.; Ehlig, P.L.; Wooden, J.L.

1993-04-01

Precambrian gneisses in the San Bernardino Mountains were first identified and described in the vicinity of Baldwin Lake by Guillou (1953). Five lithologic units mappable at 1:24,000 scale are recognized: biotite [+-] muscovite quartzofeldspathic gneiss, amphibolite, pyroxene metagabbro, augen gneiss, and biotite [+-] muscovite granitic gneiss. Baldwin gneiss with this L < S tectonite fabric is unconformably overlain by latest Proterozoic, upright, greenschist/hornfels facies quartzite (Big Bear Group). North and northeast of Baldwin Lake, the gneissic fabric is rotated toward the northwest, subparallel to the Doble fault. Along this fault, Baldwin gneiss is structurally underlain by overturned Paleozoic quartzite andmore » marble (Zabriskie Quartzite and Carrara Formation). Regional relations suggest that the Doble fault is a northeast-directed basement thrust fault of pre-Late Cretaceous age, and may be contemporaneous with late Paleozoic deformation and metamorphism of Paleozoic rocks further west in the range. Field relations suggest that Baldwin gneiss in its type area largely retains Proterozoic fabrics and mineral assemblages, despite marginal Phanerozoic reworking. Silver (1971) reported a U-Pb zircon age of ca. 1,730 Ma for Baldwin augen ( ) gneiss, from an unknown locality, and Miller and Morton (1980) reported Late Cretaceous mica K-Ar ages from a sample of augen gneiss. Preliminary Pb isotopic ratios in galena, feldspar and whole rock samples of Baldwin gneiss, and feldspars in Mesozoic plutons suggest isotopic affinity to the Mojave crustal province of Wooden and Miller (1990).« less

Active accommodation of plate convergence in Southern Iran: Earthquake locations, triggered aseismic slip, and regional strain rates

NASA Astrophysics Data System (ADS)

Barnhart, William D.; Lohman, Rowena B.; Mellors, Robert J.

2013-10-01

We present a catalog of interferometric synthetic aperture radar (InSAR) constraints on deformation that occurred during earthquake sequences in southern Iran between 1992 and 2011, and explore the implications on the accommodation of large-scale continental convergence between Saudi Arabia and Eurasia within the Zagros Mountains. The Zagros Mountains, a salt-laden fold-and-thrust belt involving ~10 km of sedimentary rocks overlying Precambrian basement rocks, have formed as a result of ongoing continental collision since 10-20 Ma that is currently occurring at a rate of ~3 cm/yr. We first demonstrate that there is a biased misfit in earthquake locations in global catalogs that likely results from neglect of 3-D velocity structure. Previous work involving two M ~ 6 earthquakes with well-recorded aftershocks has shown that the deformation observed with InSAR may represent triggered slip on faults much shallower than the primary earthquake, which likely occurred within the basement rocks (>10 km depth). We explore the hypothesis that most of the deformation observed with InSAR spanning earthquake sequences is also due to shallow, triggered slip above a deeper earthquake, effectively doubling the moment release for each event. We quantify the effects that this extra moment release would have on the discrepancy between seismically and geodetically constrained moment rates in the region, finding that even with the extra triggered fault slip, significant aseismic deformation during the interseismic period is necessary to fully explain the convergence between Eurasia and Saudi Arabia.

Geology of deep-water sandstones in the Mississippi Stanley Shale at Cossatot Falls, Arkansas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coleman, J.L. Jr.

1993-09-01

The Mississippian Stanley Shale crops out along the Cossatot River in the Ouachita Mountains of western Arkansas. Here, exposures of deep-water sandstones and shales, on recently established public lands, present a rare, three-dimensional look at sandstones of the usually obscured Stanley. Cossatot Falls, within the Cossatot River State Park Natural Area, is a series of class IV and V rapids developed on massive- to medium-bedded quartz sandstones on the northern flank of an asymmetric, thrust-faulted anticline. In western Arkansas, the Stanley Shale is a 10,000-ft (3200-m) succession of deep-water sandstone and shale. At Cossatot Falls, approximately 50 ft (155 m)more » of submarine-fan-channel sedimentary rocks are exposed during low-river stages. This section is composed primarily of sets of thinning-upward sandstone beds. With rare exceptions, the sandstones are turbidites, grading from massive, homogeneous, basal beds upward through festoon-cross-bedded thick beds, into rippled medium and thin beds. Sandstone sets are capped by thin shales and siltstones. Regional, north-northwestward paleocurrent indicators are substantiated by abundant, generally east-west ripple crests asymmetric to the north-northwest. Flute casts at the top of the sandstone sequence indicate an additional east-ward flow component. Based on regional, lithologic characteristics, the sandstones at Cossatot Falls appear to be within the Moyers Formation. The Moyers is the upper sandstone unit of the Stanley and is an oil and gas reservoir in the eastern Oklahoma Ouachita Mountains.« less

Reverse thrust performance of the QCSEE variable pitch turbofan engine

NASA Technical Reports Server (NTRS)

Samanich, N. E.; Reemsnyder, D. C.; Blodmer, H. E.

1980-01-01

Results of steady state reverse and forward to reverse thrust transient performance tests are presented. The original quiet, clean, short haul, experimental engine four segment variable fan nozzle was retested in reverse and compared with a continuous, 30 deg half angle conical exlet. Data indicated that the significantly more stable, higher pressure recovery flow with the fixed 30 deg exlet resulted in lower engine vibrations, lower fan blade stress, and approximately a 20 percent improvement in reverse thrust. Objective reverse thrust of 35 percent of takeoff thrust was reached. Thrust response of less than 1.5 sec was achieved for the approach and the takeoff to reverse thrust transients.

Geologic characterization report for the Paradox Basin Study Region, Utah Study Areas. Volume 6: Salt Valley

NASA Astrophysics Data System (ADS)

1984-12-01

Surface landforms in the Salt Valley Area are generally a function of the Salt Valley anticline and are characterized by parallel and subparallel cuestaform ridges and hogbacks and flat valley floors. The most prominent structure in the Area is the Salt Valley anticline. Erosion resulting from the Tertiary uplift of the Colorado Plateau led to salt dissolution and subsequent collapse along the crest of the anticline. Continued erosion removed the collapse material, forming an axial valley along the crest of the anticline. Paleozoic rocks beneath the salt bearing Paradox Formation consist of limestone, dolomite, sandstone, siltstone and shale. The salt beds of the Paradox formation occur in distinct cycles separated by an interbed sequence of anhydrite, carbonate, and clastic rocks. The Paradox Formation is overlain by Pennsylvanian limestone; Permian sandstone; and Mesozoic sandstone, mudstone, conglomerate and shale. No earthquakes have been reported in the area during the period of the historic record and contemporary seismicity appears to be diffusely distributed, of low level and small magnitude. The upper unit includes the Permian strata and upper Honaker trail formation.

Thrust stand evaluation of engine performance improvement algorithms in an F-15 airplane

NASA Technical Reports Server (NTRS)

Conners, Timothy R.

1992-01-01

An investigation is underway to determine the benefits of a new propulsion system optimization algorithm in an F-15 airplane. The performance seeking control (PSC) algorithm optimizes the quasi-steady-state performance of an F100 derivative turbofan engine for several modes of operation. The PSC algorithm uses an onboard software engine model that calculates thrust, stall margin, and other unmeasured variables for use in the optimization. As part of the PSC test program, the F-15 aircraft was operated on a horizontal thrust stand. Thrust was measured with highly accurate load cells. The measured thrust was compared to onboard model estimates and to results from posttest performance programs. Thrust changes using the various PSC modes were recorded. Those results were compared to benefits using the less complex highly integrated digital electronic control (HIDEC) algorithm. The PSC maximum thrust mode increased intermediate power thrust by 10 percent. The PSC engine model did very well at estimating measured thrust and closely followed the transients during optimization. Quantitative results from the evaluation of the algorithms and performance calculation models are included with emphasis on measured thrust results. The report presents a description of the PSC system and a discussion of factors affecting the accuracy of the thrust stand load measurements.

Performance characteristics of two multiaxis thrust-vectoring nozzles at Mach numbers up to 1.28

NASA Technical Reports Server (NTRS)

Wing, David J.; Capone, Francis J.

1993-01-01

The thrust-vectoring axisymmetric (VA) nozzle and a spherical convergent flap (SCF) thrust-vectoring nozzle were tested along with a baseline nonvectoring axisymmetric (NVA) nozzle in the Langley 16-Foot Transonic Tunnel at Mach numbers from 0 to 1.28 and nozzle pressure ratios from 1 to 8. Test parameters included geometric yaw vector angle and unvectored divergent flap length. No pitch vectoring was studied. Nozzle drag, thrust minus drag, yaw thrust vector angle, discharge coefficient, and static thrust performance were measured and analyzed, as well as external static pressure distributions. The NVA nozzle and the VA nozzle displayed higher static thrust performance than the SCF nozzle throughout the nozzle pressure ratio (NPR) range tested. The NVA nozzle had higher overall thrust minus drag than the other nozzles throughout the NPR and Mach number ranges tested. The SCF nozzle had the lowest jet-on nozzle drag of the three nozzles throughout the test conditions. The SCF nozzle provided yaw thrust angles that were equal to the geometric angle and constant with NPR. The VA nozzle achieved yaw thrust vector angles that were significantly higher than the geometric angle but not constant with NPR. Nozzle drag generally increased with increases in thrust vectoring for all the nozzles tested.

Episodic Growth of Fold-Thrust Belts: Insights from Finite Element Modelling

NASA Astrophysics Data System (ADS)

Yang, X.; Peel, F.; Sanderson, D. J.; McNeill, L. C.

2016-12-01

The sequential development of an imbricate thrust system was investigated using a set of 2D FEM models. This study provides new insights on how the style and location of thrust activity changes through cycles of thrust accretion by making refined measurements of the thrust system parameters through time and tracking these parameters through each cycle. In addition to conventional wedge parameters (i.e. surface slope, wedge width and height), the overall taper angle is used to determine how the critical taper angle is reached; a particular focus is on the region of outboard minor horizontal displacement provides insights into the forward propagation of material within, and in front of, the thrust wedge; tracking the position of the failure front (where the frontal thrust roots into the basal detachment) reveals the sequence and advancement of the imbricate thrusts. The model results show that a thrust system is generally composed of three deformation components: thrust wedge, pre-wedge and wedge front. A thrust belt involves growth that repeats episodically and cyclically. When a wedge reaches critical taper ( 10°), thrust movement within the wedge slows while the taper angle and wedge width gradually increase. In contrast, the displacement front (tracked here by the location of 0 m displacement) rapidly propagates forward along whilst the wedge height is fast growing. During this period, the wedge experiences a significant shortening after a new thrust initiates at the failure front, leading to an obvious decrease in wedge width. As soon as the critical taper is achieved, wedge interior (tracked here by the location of 50 m displacement) accelerates forward reducing the taper angle below critical. This is accompanied by a sudden increase in wedge width, slow advancement of displacement front, and slow uplift of the fold-thrust belt. The rapid movements within and in front of the wedge occur alternately. The model results also show that there is clear, although minor, activity (5-10 m displacement) in front of the thrust wedge, which distinguishes the failure front from the displacement front throughout the fold-thrust belt development. This spatial and temporal relationship may not have been previously recognized in natural systems.

Effects of thrust amplitude and duration of high velocity low amplitude spinal manipulation on lumbar muscle spindle responses to vertebral position and movement

PubMed Central

Cao, Dong-Yuan; Reed, William R.; Long, Cynthia R.; Kawchuk, Gregory N.; Pickar, Joel G.

2013-01-01

OBJECTIVE Mechanical characteristics of high velocity low amplitude spinal manipulations (HVLA-SM) can be variable. Sustained changes in peripheral neuronal signaling due to altered load transmission to a sensory receptor’s local mechanical environment are often considered a mechanism contributing to the therapeutic effects of spinal manipulation. The purpose of this study was to determine whether an HVLA-SM’s thrust amplitude or duration altered neural responsiveness of lumbar muscle spindles to either vertebral movement or position. METHODS Anesthetized cats (n=112) received L6 HVLA-SMs delivered to the spinous process. Cats were divided into 6 cohorts depending upon the peak thrust force (25%, 55%, 85% body weight) or thrust displacement (1, 2, 3mm) they received. Cats in each cohort received 8 thrust durations (0–250ms). Afferent discharge from 112 spindles was recorded in response to ramp and hold vertebral movement before and after the manipulation. Changes in mean instantaneous frequency (MIF) during the baseline period preceding the ramps (ΔMIFresting), during ramp movements (ΔMIFmovement), and with the vertebra held in the new position (ΔMIFposition) were compared. RESULTS Thrust duration had a small but statistically significant effect on ΔMIFresting at all six thrust amplitudes compared to control (0ms thrust duration). The lowest amplitude thrust displacement (1mm) increased ΔMIFresting at all thrust durations. For all the other thrust displacements and forces, the direction of change in ΔMIFresting was not consistent and the pattern of change was not systematically related to thrust duration. Regardless of thrust force, displacement, or duration, ΔMIFmovement and ΔMIFposition were not significantly different from control. Conclusion Relatively low amplitude thrust displacements applied during an HVLA-SM produced sustained increases in the resting discharge of paraspinal muscle spindles regardless of the duration over which the thrust was applied. However, regardless of the HVLA-SM’s thrust amplitude or duration, the responsiveness of paraspinal muscle spindles to vertebral movement and to a new vertebral position was not affected. PMID:23499141

Active transpression in the northern Calabria Apennines, southern Italy

NASA Astrophysics Data System (ADS)

Ferranti, L.; Santoro, E.; Mazzella, M. E.; Monaco, C.; Morelli, D.

2009-10-01

An integrated analysis of geomorphologic and structural data, offshore seismic profiles and local network seismicity, is used to shed light on the hitherto poorly known active deformation field that affects the Southern Apennines orogen in northern Calabria region. In the Southern Apennines, Middle Pleistocene waning of Miocene-Early Pleistocene thin-skinned frontal thrust belt motion toward the Apulian foreland to the NE was coeval to onset of regional uplift, which is documented by flights of raised marine terraces. Short-wavelength (˜ 5-10 km) and amplitude (˜ 20-50 m) undulations are superposed to the regional uplift (˜ 100 km length and ˜ 500 m amplitude scale) profile of Middle-Upper Pleistocene marine terraces on the Ionian Sea coast of northern Calabria stretching along the borders of the Sila and Pollino mountain ranges and across the intervening Sibari coastal plain. The secondary undulations spatially coincide with the last generation of ˜ W- to ˜ WNW-striking folds traced in bedrock and locally within Early to Middle Pleistocene continental to transitional deposits. The very recent activity of these structures is highlighted by a range of fluvial geomorphic anomalies and by involvement in folding and locally transpressional faulting of the Middle Pleistocene and younger depositional sequences submerged beneath the continental shelf. We argue that the local-scale, but pervasive undulations in the deformation profile of marine terraces represent shallow-crustal folds grown within a recent and still active transpressional field. A major structural culmination bound by fore- and retro-verging transpressional shear zones is represented by the Pollino mountain range and its offshore extension in the Amendolara ridge, and a further SW-directed transpressional belt is found in northern Sila and adjacent sea bottom. Epicenter distribution and focal solutions of low- to moderate crustal earthquakes illuminate the two NW-SE trending structural belts beneath the Amendolara ridge and northern Sila, where partitioning between thrust and left strike-slip motion occurs in response to ˜ E to ˜ NE directed shortening. A local ˜ NW-SE extension is recorded by fault-kinematic analysis on NE-SW striking fault segments parallel to the coast on the eastern flank of Pollino. These small-length normal faults do not form a through-going lineament, rather they accommodate the seaward collapse of the uppermost crust above the deeper shortening compartment. Conversely, the active transpression testified by geomorphic, structural and seismicity data is accommodated along deep-seated oblique back-thrusts that involve the Apulian foreland plate underlying the now inactive thin-skinned accretionary wedge down to near-Moho depths. In light of the tight interlacing between regional and local components of deformation affecting the marine terraces, we suggest that the large-scale uplift in this sector of Calabria may reflect whole crustal-scale folding. The novel seismotectonic frame reconstructed for this region is consistent with GPS velocities suggesting that large part of geodetic shortening detected between the Apennines and the Apulian block on the eastern side of southern Italy might be accommodated in northern Calabria.

New insights into the kinematics and seismotectonics of the Adria-Eurasia boundary in the eastern Alps from geodetic and seismic data

NASA Astrophysics Data System (ADS)

Serpelloni, Enrico; Vannucci, Gianfranco; Bennett, Richard A.; Anderlini, Letizia; Cavaliere, Adriano

2015-04-01

In this work we describe a new kinematic and seismotectonic model of the eastern Alps, at the boundary between Italy, Austria, Slovenia and Croatia, obtained from the analysis of geodetic (GPS) and seismological data. We use a dense GPS velocity field, obtained from integration of continuous, semi-continuous and survey-mode networks (~200 GPS stations between longitude 10°E and 17°E and latitude 44.5°N and 47.5°N) and an updated seismic and focal mechanisms catalogue, with uniformly calibrated moment magnitudes from ~1000 B.C.. Improved accuracies and precisions of GPS motion rates have been obtained by filtering displacement time-series for the spatially correlated common mode errors. The eastern Alps mark the boundary between the Adriatic microplate and the Eurasian plate through a wide zone of distributed deformation. Geodetic deformation and seismic release are more localized, and characterized by larger earthquakes, along the southeastern Alps fold-and-thrust belt, which accommodates the large part of the ~N-S Adria-Eurasia convergence, and in Slovenia, where a transition from ~N-S shortening to the eastward escape of the Pannonian Basin units occurs through a complex pattern of crustal deformation. GPS velocities well describe the overall kinematics, with a transition from NNW-ward to NE-ward motion trends (in a Eurasian frame) across Slovenia and Austria, but also show small but significant crustal deformation far from the major blocks boundaries. This may suggest internal continuous deformation or a more complex configuration of interacting tectonic blocks in the eastern Alps. This second hypothesis is taken into account and tested in this work. We use seismic moment release rate maps, active faults databases and inspections of GPS velocities in different local frames to define the geometry of a kinematic block model, constrained by GPS horizontal velocities, in order to estimate blocks rotations and elastic strain at blocks bounding faults. The improved GPS velocity field highlights significant strain accumulation off the main thrust fault segments in the southeastern Alps, in regions stroke by large (M>6.5) historical earthquakes (e.g., the 1117 Verona and the 1695 Asolo events). This is evident in the Venetian plain, where GPS highlights significant shortening in areas that are tens of km southward of the south Alpine mountain front. In the Italian southeastern Alps results from the block model, constrained by a denser GPS velocity field (e.g., around the Montello fault), put new lights on i) the way the Adria-Eurasia convergence is partitioned across the southeast Alpine mountain range, ii) about interseismic coupling along the main thrust faults and iii) the way N-S shortening is transferred, through right-lateral shear across the Dinaric system, to shortening across the Sava folds in Slovenia. In the end, a comparison of the estimated seismic moment release rates and the seismic moment accumulation rates, estimated from the model velocities, provide new insights into the seismic potential of the study region.

Crustal thickening in Gansu-Qinghai, lithospheric mantle subduction, and oblique, strike-slip controlled growth of the Tibet plateau

NASA Astrophysics Data System (ADS)

Meyer, B.; Tapponnier, P.; Bourjot, L.; Métivier, F.; Gaudemer, Y.; Peltzer, G.; Shunmin, Guo; Zhitai, Chen

1998-10-01

Fieldwork complemented by SPOT image analysis throws light on current crustal shortening processes in the ranges of northeastern Tibet (Gansu and Qinghai provinces, China). The ongoing deformation of Late-Pleistocene bajada aprons in the forelands of the ranges involves folding, at various scales, and chiefly north-vergent, seismogenic thrusts. The most active thrusts usually break the ground many kilometres north of the range-fronts, along the northeast limbs of growing, asymmetric ramp-anticlines. Normal faulting at the apex of other growing anticlines, between the range fronts and the thrust breaks, implies slip on blind ramps connecting distinct active décollement levels that deepen southwards. The various patterns of uplift of the bajada surfaces can be used to constrain plausible links between contemporary thrusts downsection. Typically, the foreland thrusts and décollements appear to splay from master thrusts that plunge at least 15-20 km down beneath the high ranges. Plio-Quaternary anticlinal ridges rising to more than 3000 m a.s.l. expose Palaeozoic metamorphic basement in their core. In general, the geology and topography of the ranges and forelands imply that structural reliefs of the order of 5-10 km have accrued at rates of 1-2 mm yr-1 in approximately the last 5 Ma. From hill to range size, the elongated reliefs that result from such Late-Cenozoic, NE-SW shortening appear to follow a simple scaling law, with roughly constant length/width ratio, suggesting that they have grown self-similarly. The greatest mountain ranges, which are over 5.5 km high, tens of kilometres wide and hundreds of kilometres long may thus be interpreted to have formed as NW-trending ramp anticlines, at the scale of the middle-upper crust. The fairly regular, large-scale arrangement of those ranges, with parallel crests separated by piggy-back basins, the coevality of many parallel, south-dipping thrusts, and a change in the scaling ratio (from ~5 to 8) for range widths greater than ~30 km further suggests that they developed as a result of the northeastward migration of large thrust ramps above a broad décollement dipping SW at a shallow angle in the middle-lower crust. This, in turn, suggests that the 400-500 km-wide crustal wedge that forms the northeastern edge of the Tibet-Qinghai plateau shortens and thickens as a thick-skinned accretionary prism decoupled from the stronger upper mantle underneath. Such a thickening process must have been coupled with propagation of the Altyn Tagh fault towards the ENE because most thrust traces merge northwestwards with active branches of this fault, after veering clockwise. This process appears to typify the manner in which the Tibet-Qinghai highlands have expanded their surface area in the Neogene. The present topography and structure imply that, during much of that period, the Tibet plateau grew predominantly towards the northeast or east-northeast, but only marginally towards the north-northwest. This was accomplished by the rise, in fairly fast succession, of the Arka Tagh, Qiman Tagh, Mahan shan, Tanghenan Shan, and other NW-trending mountain ranges splaying southeastwards from the Altyn Tagh, isolating the Aqqik-Ayakkum Kol, Qaidam, Suhai and other catchments and basins that became incorporated into the highland mass as intermontane troughs. The tectonic cut-off of catchments and the ultimate infilling of basins by debris from the adjacent ranges, a result of tectonically forced internal drainage, have thus been essential relief-smoothing factors, yielding the outstandingly flat topography that makes Tibet a plateau. Using Late-Mesozoic and Neogene horizons as markers, the retrodeformation of sections across the West Qilian Ranges and Qaidam basin implies at least ~150 km of N30°E Neogene shortening. On a broader scale, taking erosion into account, and assuming isostatic compensation and an initial crustal thickness comparable to that of the Gobi platform (47.5+/-5 km), minimum amounts of Late-Cenozoic crustal shortening on NE sections between the Kunlun fault and the Hexi corridor are estimated to range between 100 and 200 km. In keeping with the inference of a deep crustal décollement and with the existence of Mid-Miocene to Pliocene plutonism and volcanism south of the Kunlun range, such values suggest that the lithospheric mantle of the Qaidam plunged obliquely into the asthenosphere south of that range to minimum depths of the order of 200-300 km. A minimum of ~150 km of shortening in the last ~10 Ma, consistent with the average age of the earliest volcanic-plutonic rocks just south of the Kunlun (~10.8 Ma) would imply average Late-Cenozoic rates of shortening and regional uplift in NE Tibet of at least ~15 mm yr-1 and ~0.2 mm yr-1, respectively. Such numbers are consistent with a cumulative sinistral offset and slip rate of at least ~200 km and ~2 cm yr-1, respectively, on the Altyn Tagh fault east of 88°E. The fault may have propagated more than 1000 km, to 102°E, in the last 10 Ma. Our study of ongoing tectonics in northeast Tibet is consistent with a scenario in which, while the Himalayas-Gangdese essentially `stagnated' above India's subducting mantle, much of Tibet grew by thickening of the Asian crust, as propagation of large, lithospheric, strike-slip shear zones caused the opposite edge of the plateau to migrate far into Asia. The Asian lithospheric mantle, decoupled from the crust, appears to have subducted southwards along the two Mesozoic sutures that cut Tibet north of the Gangdese, rather than to have thickened. The Bangong-Nujiang suture was probably reactivated earlier than the Jinsha-Kunlun suture, located farther north. Overall, the large-scale deformation bears a resemblance to plate tectonics at obliquely convergent margins, including slip-partioning along large strike-slip faults such as the Altyn Tagh and Kunlun faults. Simple mechanisms at the level of the lithospheric mantle are merely hidden by the broader distribution and greater complexity of strain in the crust.

A simplified gross thrust computing technique for an afterburning turbofan engine

NASA Technical Reports Server (NTRS)

Hamer, M. J.; Kurtenbach, F. J.

1978-01-01

A simplified gross thrust computing technique extended to the F100-PW-100 afterburning turbofan engine is described. The technique uses measured total and static pressures in the engine tailpipe and ambient static pressure to compute gross thrust. Empirically evaluated calibration factors account for three-dimensional effects, the effects of friction and mass transfer, and the effects of simplifying assumptions for solving the equations. Instrumentation requirements and the sensitivity of computed thrust to transducer errors are presented. NASA altitude facility tests on F100 engines (computed thrust versus measured thrust) are presented, and calibration factors obtained on one engine are shown to be applicable to the second engine by comparing the computed gross thrust. It is concluded that this thrust method is potentially suitable for flight test application and engine maintenance on production engines with a minimum amount of instrumentation.

Low Thrust Orbital Maneuvers Using Ion Propulsion

NASA Astrophysics Data System (ADS)

Ramesh, Eric

2011-10-01

Low-thrust maneuver options, such as electric propulsion, offer specific challenges within mission-level Modeling, Simulation, and Analysis (MS&A) tools. This project seeks to transition techniques for simulating low-thrust maneuvers from detailed engineering level simulations such as AGI's Satellite ToolKit (STK) Astrogator to mission level simulations such as the System Effectiveness Analysis Simulation (SEAS). Our project goals are as follows: A) Assess different low-thrust options to achieve various orbital changes; B) Compare such approaches to more conventional, high-thrust profiles; C) Compare computational cost and accuracy of various approaches to calculate and simulate low-thrust maneuvers; D) Recommend methods for implementing low-thrust maneuvers in high-level mission simulations; E) prototype recommended solutions.

On the calculation of low-thrust fail-safe trajectories

NASA Technical Reports Server (NTRS)

Sauer, C. G., Jr.

1975-01-01

A guidance algorithm is developed for a low-thrust spacecraft such that target intercept is possible in spite of premature thrust termination along the trajectory. Such a trajectory is called a 'fail-safe' trajectory and the spacecraft thrust is utilized to minimize the relative target-spacecraft approach speed. The fail-safe guidance algorithm is solved using the concept of a critical thrust plane and a non-critical thrust direction. Several examples of fail-safe guidance are presented for a solar-electric propulsion flyby mission to the comet Encke.

Initiation of a thrust fault revealed by analog experiments

NASA Astrophysics Data System (ADS)

Dotare, Tatsuya; Yamada, Yasuhiro; Adam, Juergen; Hori, Takane; Sakaguchi, Hide

2016-08-01

To reveal in detail the process of initiation of a thrust fault, we conducted analog experiments with dry quartz sand using a high-resolution digital image correlation technique to identify minor shear-strain patterns for every 27 μm of shortening (with an absolute displacement accuracy of 0.5 μm). The experimental results identified a number of "weak shear bands" and minor uplift prior to the initiation of a thrust in cross-section view. The observations suggest that the process is closely linked to the activity of an adjacent existing thrust, and can be divided into three stages. Stage 1 is characterized by a series of abrupt and short-lived weak shear bands at the location where the thrust will subsequently be generated. The area that will eventually be the hanging wall starts to uplift before the fault forms. The shear strain along the existing thrust decreases linearly during this stage. Stage 2 is defined by the generation of the new thrust and active displacements along it, identified by the shear strain along the thrust. The location of the new thrust may be constrained by its back-thrust, generally produced at the foot of the surface slope. The activity of the existing thrust falls to zero once the new thrust is generated, although these two events are not synchronous. Stage 3 of the thrust is characterized by a constant displacement that corresponds to the shortening applied to the model. Similar minor shear bands have been reported in the toe area of the Nankai accretionary prism, SW Japan. By comparing several transects across this subduction margin, we can classify the lateral variations in the structural geometry into the same stages of deformation identified in our experiments. Our findings may also be applied to the evaluation of fracture distributions in thrust belts during unconventional hydrocarbon exploration and production.

Investigation of Asymmetric Thrust Detection with Demonstration in a Real-Time Simulation Testbed

NASA Technical Reports Server (NTRS)

Chicatelli, Amy; Rinehart, Aidan W.; Sowers, T. Shane; Simon, Donald L.

2015-01-01

The purpose of this effort is to develop, demonstrate, and evaluate three asymmetric thrust detection approaches to aid in the reduction of asymmetric thrust-induced aviation accidents. This paper presents the results from that effort and their evaluation in simulation studies, including those from a real-time flight simulation testbed. Asymmetric thrust is recognized as a contributing factor in several Propulsion System Malfunction plus Inappropriate Crew Response (PSM+ICR) aviation accidents. As an improvement over the state-of-the-art, providing annunciation of asymmetric thrust to alert the crew may hold safety benefits. For this, the reliable detection and confirmation of asymmetric thrust conditions is required. For this work, three asymmetric thrust detection methods are presented along with their results obtained through simulation studies. Representative asymmetric thrust conditions are modeled in simulation based on failure scenarios similar to those reported in aviation incident and accident descriptions. These simulated asymmetric thrust scenarios, combined with actual aircraft operational flight data, are then used to conduct a sensitivity study regarding the detection capabilities of the three methods. Additional evaluation results are presented based on pilot-in-the-loop simulation studies conducted in the NASA Glenn Research Center (GRC) flight simulation testbed. Data obtained from this flight simulation facility are used to further evaluate the effectiveness and accuracy of the asymmetric thrust detection approaches. Generally, the asymmetric thrust conditions are correctly detected and confirmed.

Investigation of Asymmetric Thrust Detection with Demonstration in a Real-Time Simulation Testbed

NASA Technical Reports Server (NTRS)

Chicatelli, Amy K.; Rinehart, Aidan W.; Sowers, T. Shane; Simon, Donald L.

2016-01-01

The purpose of this effort is to develop, demonstrate, and evaluate three asymmetric thrust detection approaches to aid in the reduction of asymmetric thrust-induced aviation accidents. This paper presents the results from that effort and their evaluation in simulation studies, including those from a real-time flight simulation testbed. Asymmetric thrust is recognized as a contributing factor in several Propulsion System Malfunction plus Inappropriate Crew Response (PSM+ICR) aviation accidents. As an improvement over the state-of-the-art, providing annunciation of asymmetric thrust to alert the crew may hold safety benefits. For this, the reliable detection and confirmation of asymmetric thrust conditions is required. For this work, three asymmetric thrust detection methods are presented along with their results obtained through simulation studies. Representative asymmetric thrust conditions are modeled in simulation based on failure scenarios similar to those reported in aviation incident and accident descriptions. These simulated asymmetric thrust scenarios, combined with actual aircraft operational flight data, are then used to conduct a sensitivity study regarding the detection capabilities of the three methods. Additional evaluation results are presented based on pilot-in-the-loop simulation studies conducted in the NASA Glenn Research Center (GRC) flight simulation testbed. Data obtained from this flight simulation facility are used to further evaluate the effectiveness and accuracy of the asymmetric thrust detection approaches. Generally, the asymmetric thrust conditions are correctly detected and confirmed.

Combined high and low-thrust geostationary orbit insertion with radiation constraint

NASA Astrophysics Data System (ADS)

Macdonald, Malcolm; Owens, Steven Robert

2018-01-01

The sequential use of an electric propulsion system is considered in combination with a high-thrust propulsion system for application to the propellant-optimal Geostationary Orbit insertion problem, whilst considering both temporal and radiation flux constraints. Such usage is found to offer a combined propellant mass saving when compared with an equivalent high-thrust only transfer. This propellant mass saving is seen to increase as the allowable transfer duration is increased, and as the thrust from the low-thrust system is increased, assuming constant specific impulse. It was found that the required plane change maneuver is most propellant-efficiently performed by the high-thrust system. The propellant optimal trajectory incurs a significantly increased electron flux when compared to an equivalent high-thrust only transfer. However, the electron flux can be reduced to a similar order of magnitude by increasing the high-thrust propellant consumption, whilst still delivering an improved mass fraction.

Thrust Control Loop Design for Electric-Powered UAV

NASA Astrophysics Data System (ADS)

Byun, Heejae; Park, Sanghyuk

2018-04-01

This paper describes a process of designing a thrust control loop for an electric-powered fixed-wing unmanned aerial vehicle equipped with a propeller and a motor. In particular, the modeling method of the thrust system for thrust control is described in detail and the propeller thrust and torque force are modeled using blade element theory. A relation between current and torque of the motor is obtained using an experimental setup. Another relation between current, voltage and angular velocity is also obtained. The electric motor and the propeller dynamics are combined to model the thrust dynamics. The associated trim and linearization equations are derived. Then, the thrust dynamics are coupled with the flight dynamics to allow a proper design for the thrust loop in the flight control. The proposed method is validated by an application to a testbed UAV through simulations and flight test.

Palinspastic reconstruction of the Alpine thrust belt at the Alpine-Carpathian transition - A geological Sudoku

NASA Astrophysics Data System (ADS)

Beidinger, A.; Decker, K.; Zamolyi, A.; Hölzel, M.; Hoprich, M.; Strauss, P.

2009-04-01

The palinspastic reconstruction of the Austroalpine thrust belt is part of the project Karpatian Tectonics, which is funded by OMV Austria. The objective is to reconstruct the evolution of the thrust belt through the Early to Middle Miocene in order to obtain information on the palaeogeographic position of the Northern Calcareous Alps (NCA) in the region of the present Vienna Basin. A particular goal of the study is to constrain the position of reservoir rocks within the Rhenodanubic Flysch units and the NCA with respect to the autochthonous Malmian source rocks overlying the European basement below the Alpine-Carpathian thrust wedge, and to constrain the burial history of these source rocks. Reconstruction uses regional 2D seismic lines crossing from the European foreland into the fold-thrust belt, 3D seismic data covering the external thrust sheets, and lithostratigraphic data from a total of 51 selected wells, which were drilled and provided by OMV Austria. The main criterion, whether a well was suitable for palinspastic reconstruction or not, was its penetration of Alpine thrust sheets down to the Autochthonous Molasse of the foreland. Additional wells, which do not penetrate the entire Alpine thrust complex but include the Allochthonous Molasse or the external Alpine-Carpathian nappes (Waschberg and Roseldorf thrust unit, Rhenodanubic Flysch nappes) in their well path, were also taken into account. The well data in particular comprise stratigraphic information on the youngest overthrust sediments of the different thrust units and the underlying Autochthonous foreland Molasse. These data allow constraining the timing of thrust events in the allochthonous thrust units and overthrusting of the Autochthonous Molasse. In the particular case of overthrust Autochthonous Molasse, additionally to the timing of overthrusting, which can be derived from the youngest overthrust sediments, the palaeogeographic position of the Alpine Carpathian thrust front could directly be inferred from well data for the specific time period. By further utilization of geological maps, geological cross sections and two regional c. 80 km long composite 2D seismic sections through the external Alpine thrusts, the positions of major thrusts could be approximated for five time slices. This procedure was applied for the front of the allochthonous Molasse units, the floor thrust of the Roseldorf thrust unit, the Waschberg thrust unit and the frontal thrusts of the Rhenodanubic Flysch and the NCA. In addition, several out-of-sequence thrusts within the Waschberg unit, the Molasse unit, the Rhenodanubic Flysch and the Calcareous Alps (floor thrust of the NCA and two internal thrusts) were taken into account. The reconstruction results in 5 palinspastic maps for the time slices early Egerian (25 Ma), early Eggenburgian (20 Ma), Ottnangian (17.5 Ma), Lower Karpatian (16.5 Ma) and the Karpatian/ Badenian stage boundary (16 Ma). Convergence rates, which were calculated for the four intervening time intervals, range from about 3 mm/yr to 5 mm/yr. These values compare well with estimated convergence rates reconstructed for the Miocene in the western Eastern Alps (Schmid et al., 1996), as well as with plate tectonic constraints on Tertiary convergence rates (Dewey et al., 1989). Dewey, J., Helman, M.L., Turco, E., Hutton, D.H.W.&Knott, S.D., 1989. Kinematics of the western Mediterranean, in: N.P. Coward, D. Dietrich & R.G. Park (eds.), Alpine Tectonics, Geol. Soc. Spec. Publ., 45: 265-283. Schmid, S.M., Pfiffner, O.A., Frotzheim, N., Schönborn, G. & Kissling, E., 1996. Geophysical-geological transect and tectonic evolution of the Swiss-Italian Alps. Tectonics, 15: 1036-1064.

Quantifying the high-velocity, low-amplitude spinal manipulative thrust: a systematic review.

PubMed

Downie, Aron S; Vemulpad, Subramanyam; Bull, Peter W

2010-09-01

The purpose of this study was to systematically review studies that quantify the high-velocity, low-amplitude (HVLA) spinal thrust, to qualitatively compare the apparatus used and the force-time profiles generated, and to critically appraise studies involving the quantification of thrust as an augmented feedback tool in psychomotor learning. A search of the literature was conducted to identify the sources that reported quantification of the HVLA spinal thrust. MEDLINE-OVID (1966-present), MANTIS-OVID (1950-present), and CINAHL-EBSCO host (1981-present) were searched. Eligibility criteria included that thrust subjects were human, animal, or manikin and that the thrust type was a hand-delivered HVLA spinal thrust. Data recorded were single force, force-time, or displacement-time histories. Publications were in English language and after 1980. The relatively small number of studies, combined with the diversity of method and data interpretation, did not enable meta-analysis. Twenty-seven studies met eligibility criteria: 17 studies measured thrust as a primary outcome (13 human, 2 cadaver, and 2 porcine). Ten studies demonstrated changes in psychomotor learning related to quantified thrust data on human, manikin, or other device. Quantifiable parameters of the HVLA spinal thrust exist and have been described. There remain a number of variables in recording that prevent a standardized kinematic description of HVLA spinal manipulative therapy. Despite differences in data between studies, a relationship between preload, peak force, and thrust duration was evident. Psychomotor learning outcomes were enhanced by the application of thrust data as an augmented feedback tool. Copyright © 2010 National University of Health Sciences. Published by Mosby, Inc. All rights reserved.

Thrust Generation with Low-Power Continuous-Wave Laser and Aluminum Foil Interaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Horisawa, Hideyuki; Sumida, Sota; Funaki, Ikkoh

2010-05-06

The micro-newton thrust generation was observed through low-power continuous-wave laser and aluminum foil interaction without any remarkable ablation of the target surface. To evaluate the thrust characteristics, a torsion-balance thrust stand capable for the measurement of the thrust level down to micro-Newton ranges was developed. In the case of an aluminum foil target with 12.5 micrometer thickness, the maximum thrust level was 15 micro-newtons when the laser power was 20 W, or about 0.75 N/MW. It was also found that the laser intensity, or laser power per unit area, irradiated on the target was significantly important on the control ofmore » the thrust even under the low-intensity level.« less

Seismic interpretation and thrust tectonics of the Amadeus Basin, central Australia, along the BMR regional seismic line

NASA Astrophysics Data System (ADS)

Shaw, Russell D.; Korsch, Russell J.; Wright, C.; Goleby, B. R.

At the northern margin of the Amadeus Basin the monoclinal upturn (the MacDonnell Homocline) is interpreted to be the result of rotation and limited back-thrusting of the sedimentary sequence in front of a southerly-directed, imbricate basement thrust-wedge. This thrust complex is linked at depth to the crust-cutting Redbank Thrust Zone. In the northern part of the basin immediately to the south, regional seismic reflection profiling across the Missionary Plain shows a sub-horizontal, north-dipping, parautochthonous sedimentary sequence between about 8.5 km and 12.0 km thick. This sedimentary sequence shows upturning only at the northern and southern extremities, and represents an unusual, relatively undeformed region between converging thrust systems. In this intervening region, the crust appears to have been tilted downwards and northwards in response to the upthrusting to the north. Still farther to the south, the vertical uplift of the southern hanging wall of the Gardiner Thrust is about 6 km. Seismic reflection profiling in the region immediately south of the Gardiner Thrust indicates repetition of the sedimentary sequence. At the far end of the profile, in the Kernot Range, an imbricate thrust system fans ahead of a ramp-flat thrust pair. This thrust system (the Kernot Range Thrust System) occurs immediately north of an aeromagnetic domain boundary which marks the southern limit of a central ridge region characterized by thin Palaeozoic sedimentary cover and shallow depths to magnetic basement. A planar seismic event, imaged to a depth of at least 18 km, may correspond to the same boundary and is interpreted as a pre-basin Proterozoic thrust. Overall, the structure in the shallow sedimentary section in the central-southern region of the Amadeus Basin indicates that north-directed thrusting during the Dovonian-Carboniferous Alice Springs Orogeny was thin-skinned. During this orogeny an earlier thrust system, formed during the Petermann Ranges Orogeny and precursor orogenies in the Late Proterozoic, was reactivated with Proterozoic salt deposits localising the decollement zone. The Alice Springs Orogeny also reactivated a major mid Proterozoic province boundary in the basement to the north of the basin, resulting in major thrust movement at the northern basin margin.

Thrust augmentation nozzle (TAN) concept for rocket engine booster applications

NASA Astrophysics Data System (ADS)

Forde, Scott; Bulman, Mel; Neill, Todd

2006-07-01

Aerojet used the patented thrust augmented nozzle (TAN) concept to validate a unique means of increasing sea-level thrust in a liquid rocket booster engine. We have used knowledge gained from hypersonic Scramjet research to inject propellants into the supersonic region of the rocket engine nozzle to significantly increase sea-level thrust without significantly impacting specific impulse. The TAN concept overcomes conventional engine limitations by injecting propellants and combusting in an annular region in the divergent section of the nozzle. This injection of propellants at moderate pressures allows for obtaining high thrust at takeoff without overexpansion thrust losses. The main chamber is operated at a constant pressure while maintaining a constant head rise and flow rate of the main propellant pumps. Recent hot-fire tests have validated the design approach and thrust augmentation ratios. Calculations of nozzle performance and wall pressures were made using computational fluid dynamics analyses with and without thrust augmentation flow, resulting in good agreement between calculated and measured quantities including augmentation thrust. This paper describes the TAN concept, the test setup, test results, and calculation results.

Deep crustal structure of the UAE-Oman mountain belt from seismic and gravity data

NASA Astrophysics Data System (ADS)

Pilia, S.; Tanveer, M.; Ali, M.; Watts, A. B.; Searle, M. P.; Keats, B. S.

2016-12-01

The UAE-Oman mountains constitute a 700 km long, 50 km wide compressional orogenic belt that developed during the Cenozoic on an underlying extensional Tethyan rifted margin. It contains the world's largest and best-exposed thrust sheet of oceanic crust and upper mantle (Semail Ophiolite), which was obducted onto the Arabian rifted continental margin during the Late Cretaceous. Although the shallow structure of the UAE-Oman mountain belt is reasonably well known through the exploitation of a diverse range of techniques, information on deeper structure remains little. Moreover, the mechanisms by which dense oceanic crustal and mantle rocks are emplaced onto less dense and more buoyant continental crust are still controversial and remain poorly understood. The focus here is on an active-source seismic and gravity E-W transect extending from the UAE-mountain belt to the offshore. Seismic refraction data were acquired using the survey ship M/V Hawk Explorer, which was equipped with a large-volume airgun array (116 liters). About 400 air gun shots at 50-second time interval were recorded on land by eight broadband seismometers. In addition, reflection data were acquired at 20 seconds interval and recorded by a 5-km-long multichannel streamer. Results presented here include an approximately 85 km long (stretching about 35 km onshore and 50 km offshore) P-wave velocity crustal profile derived by a combination of forward modelling and inversion of both diving and reflected wave traveltimes using RAYINVR software. We employ a new robust algorithm based on a Monte Carlo approach (VMONTECARLO) to address the velocity model uncertainties. We find ophiolite seismic velocities of about 5.5 km/s, underlain by a thin layer of slower material (about 4.5 km/s). Furthermore, the velocity model reveals a Moho depth that rises from ca 30 km in the west to ca 20 km in the east. A poststack depth-migrated profile (about 50 km long) coincident with the offshore part of the refraction profile shows a thick sequence (up to 6 km) of seaward dipping sediments that are offset by a number of listric (normal) faults, some of which intersect the seabed and so reflect recent tectonic activity. The trend of the Bouguer anomaly provides further constraints on the deeper structure of the margin and appears to confirm the presence of a stretched crust.

Geology, geochronology, and paleogeography of the southern Sonoma volcanic field and adjacent areas, northern San Francisco Bay region, California

USGS Publications Warehouse

Wagner, David L.; Saucedo, George J.; Clahan, Kevin B.; Fleck, Robert J.; Langenheim, Victoria E.; McLaughlin, Robert J.; Sarna-Wojcicki, Andrei M.; Allen, James R.; Deino, Alan L.

2011-01-01

Recent geologic mapping in the northern San Francisco Bay region (California, USA) supported by radiometric dating and tephrochronologic correlations, provides insights into the framework geology, stratigraphy, tectonic evolution, and geologic history of this part of the San Andreas transform plate boundary. There are 25 new and existing radiometric dates that define three temporally distinct volcanic packages along the north margin of San Pablo Bay, i.e., the Burdell Mountain Volcanics (11.1 Ma), the Tolay Volcanics (ca. 10–8 Ma), and the Sonoma Volcanics (ca. 8–2.5 Ma). The Burdell Mountain and the Tolay Volcanics are allochthonous, having been displaced from the Quien Sabe Volcanics and the Berkeley Hills Volcanics, respectively. Two samples from a core of the Tolay Volcanics taken from the Murphy #1 well in the Petaluma oilfield yielded ages of 8.99 ± 0.06 and 9.13 ± 0.06 Ma, demonstrating that volcanic rocks exposed along Tolay Creek near Sears Point previously thought to be a separate unit, the Donnell Ranch volcanics, are part of the Tolay Volcanics. Other new dates reported herein show that volcanic rocks in the Meacham Hill area and extending southwest to the Burdell Mountain fault are also part of the Tolay Volcanics. In the Sonoma volcanic field, strongly bimodal volcanic sequences are intercalated with sediments. In the Mayacmas Mountains a belt of eruptive centers youngs to the north. The youngest of these volcanic centers at Sugarloaf Ridge, which lithologically, chemically, and temporally matches the Napa Valley eruptive center, was apparently displaced 30 km to the northwest by movement along the Carneros and West Napa faults. The older parts of the Sonoma Volcanics have been displaced at least 28 km along the Rodgers Creek fault since ca. 7 Ma. The Petaluma Formation also youngs to the north along the Rodgers Creek–Hayward fault and the Bennett Valley fault. The Petaluma basin formed as part of the Contra Costa basin in the Late Miocene and was displaced to its present location along the Rodgers Creek–Hayward and older faults. The Tolay fault, previously thought to be a major dextral fault, is part of a fold-and-thrust belt that does not exhibit lateral displacement.

The Colorado front range: anatomy of a Laramide uplift

USGS Publications Warehouse

Kellogg, Karl; Bryant, Bruce; Reed, John C.

2004-01-01

Along a transect across the Front Range from Denver to the Blue River valley near Dillon, the trip explores the geologic framework and Laramide (Late Cretaceous to early Eocene) uplift history of this basement-cored mountain range. Specific items for discussion at various stops are (1) the sedimentary and structural record along the upturned eastern margin of the range, which contains several discontinuous, east-directed reverse faults; (2) the western structural margin of the range, which contains a minimum of 9 km of thrust overhang and is significantly different in structural style from the eastern margin; (3) mid- to late-Tertiary modifications to the western margin of the range from extensional faulting along the northern Rio Grande rift trend; (4) the thermal and uplift history of the range as revealed by apatite fission track analysis; (5) the Proterozoic basement of the range, including the significance of northeast-trending shear zones; and (6) the geologic setting of the Colorado mineral belt, formed during Laramide and mid-Tertiary igneous activity.

Origin of a major cross-element zone: Moroccan Rif

NASA Astrophysics Data System (ADS)

Morley, C. K.

1987-08-01

Alpine age (Oligocene-Miocene) deformation in the western Mediterranean formed the Rif mountain belt of northern Morocco. A linear east-northeast-west-southwest trend of cross elements from Jebah (Mediterranean coast) to Arbaoua (near the Atlantic coast) extends through several thrust sheets in the western Rif. The cross elements are manifest as a lateral ramp, the northern limit of a large culmination, and they affect syntectonic turbidite sandstone distribution. Gravity anomalies indicate that the cross-element zone is coincident with a transition zone from normal thickness to thinner continental crust. It is suggested that an early Mesozoic strike-slip fault system related to rifting of North America from North Africa caused a strong east-northeast-west-southwest, basement block-fault trend to form on the normal thickness side of the thick-to-thin continental crustal transition zone. This trend later influenced the position of the Alpine age cross-element zone that traverses several different Mesozoic and Tertiary basins, inverted during the Alpine deformation.

Spreading volcanoes

USGS Publications Warehouse

Borgia, A.; Delaney, P.T.; Denlinger, R.P.

2000-01-01

As volcanoes grow, they become ever heavier. Unlike mountains exhumed by erosion of rocks that generally were lithified at depth, volcanoes typically are built of poorly consolidated rocks that may be further weakened by hydrothermal alteration. The substrates upon which volcanoes rest, moreover, are often sediments lithified by no more than the weight of the volcanic overburden. It is not surprising, therefore, that volcanic deformation includes-and in the long term is often dominated by-spreading motions that translate subsidence near volcanic summits to outward horizontal displacements around the flanks and peripheries. We review examples of volcanic spreading and go on to derive approximate expressions for the time volcanoes require to deform by spreading on weak substrates. We also demonstrate that shear stresses that drive low-angle thrust faulting from beneath volcanic constructs have maxima at volcanic peripheries, just where such faults are seen to emerge. Finally, we establish a theoretical basis for experimentally derived scalings that delineate volcanoes that spread from those that do not.

Origin of a major cross-element zone: Moroccan Rif

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morley, C.K.

1987-08-01

Alpine age (Oligocene-Miocene) deformation in the western Mediterranean formed the Rif mountain belt of northern Morocco. A linear east-northeast-west-southwest trend of cross elements from Jebah (Mediterranean coast) to Arbaoua (near the Atlantic coast) extends through several thrust sheets in the western Rif. The cross elements are manifest as a lateral ramp, the northern limit of a large culmination, and they affect syntectonic turbidite sandstone distribution. Gravity anomalies indicate that the cross-element zone is coincident with a transition zone from normal thickness to thinner continental crust. It is suggested that an early Mesozoic strike-slip fault system related to rifting of Northmore » America from North Africa caused a strong east-northeast-west-southwest, basement block-fault trend to form on the normal thickness side of the thick-to-thin continental crustal transition zone. This trend later influenced the position of the Alpine age cross-element zone that traverses several different Mesozoic and Tertiary basins, inverted during the Alpine deformation.« less

Harper Creek and Cuyamaca Reservoir gneisses, CLMSZ: Late Jurassic plutons of the Peninsular Ranges batholith

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, J.; Girty, G.H.; Girty, M.S.

1993-04-01

The Cuyamaca Laguna Mountains shear zone (CLMSZ), southern California, has been interpreted to represent east-over-west thrusting resulting from Early Cretaceous arc-continent collision. Near Pine Valley, the western margin of the CLMSZ is underlain by the Harper Creek (HCg) and Cuyamaca Reservoir (CRg) gneisses. U-Pb zircon studies indicate ages of 161 [+-] 17 Ma and 156 [+-] 12 Ma for the Hcg and an age of 158 Ma for the CRg. Geochemically the HCg and CRg are calc-alkaline and peraluminous. Trace element data suggest a magmatic arc setting. Modal and normative mineralogy suggest granodioritic and tonalitic protoliths. Mineral assemblages indicate uppermore » greenschist facies to lower amphibolite grade conditions during deformation. The HCg and CRg were deformed prior to the emplacement of the adjacent 118 [+-] 9 Ma Pine Valley pluton. Structural fabrics described above suggest NE-SW contraction and subvertical extension and are thus compatible with the arc-continent collisional model proposed by earlier workers.« less

Preliminary interpretation of industry two-dimensional seismic data from Susitna Basin, south-central Alaska

USGS Publications Warehouse

Lewis, Kristen A.; Potter, Christopher J.; Shah, Anjana K.; Stanley, Richard G.; Haeussler, Peter J.; Saltus, Richard W.

2015-07-30

The eastern seismic lines show evidence of numerous short-wavelength antiforms that appear to correspond to a series of northeast-trending lineations observed in aeromagnetic data, which have been interpreted as being due to folding of Paleogene volcanic strata. The eastern side of the basin is also cut by a number of reverse faults and thrust faults, the majority of which strike north-south. The western side of the Susitna Basin is cut by a series of regional reverse faults and is characterized by synformal structures in two fault blocks between the Kahiltna River and Skwentna faults. These synforms are progressively deeper to the west in the footwalls of the east-vergent Skwentna and northeast-vergent Beluga Mountain reverse faults. Although the seismic data are limited to the south, we interpret a potential regional south-southeast-directed reverse fault striking east-northeast on the east side of the basin that may cross the entire southern portion of the basin.

Architecture-Led Safety Process

DTIC Science & Technology

2016-12-01

Action Hazard Guide 42 Table 18: Comparative Table of Safety and Reliability Terms 47 CMU/SEI-2016-TR-012 | SOFTWARE ENGINEERING INSTITUTE...provides too much thrust Engine is slow to pro- vide commanded thrust (increase or de- crease) Engine will not shut- down when com - manded...Thrust level must be provided at the com - manded level H4: Engine is slow to provide commanded thrust SC3: Engine must provide commanded thrust in

Statistical error model for a solar electric propulsion thrust subsystem

NASA Technical Reports Server (NTRS)

Bantell, M. H.

1973-01-01

The solar electric propulsion thrust subsystem statistical error model was developed as a tool for investigating the effects of thrust subsystem parameter uncertainties on navigation accuracy. The model is currently being used to evaluate the impact of electric engine parameter uncertainties on navigation system performance for a baseline mission to Encke's Comet in the 1980s. The data given represent the next generation in statistical error modeling for low-thrust applications. Principal improvements include the representation of thrust uncertainties and random process modeling in terms of random parametric variations in the thrust vector process for a multi-engine configuration.

Investigation of Thrust Augmentation of a 1600-pound Thrust Centrifugal-flow-type Turbojet Engine by Injection of Refrigerants at Compressor Inlets

NASA Technical Reports Server (NTRS)

Jones, William L.; Dowman, Harry W.

1947-01-01

Investigations were conducted to determine effectiveness of refrigerants in increasing thrust of turbojet engines. Mixtures of water an alcohol were injected for a range of total flows up to 2.2 lb/sec. Kerosene was injected into inlets covering a range of injected flows up to approximately 30% of normal engine fuel flow. Injection of 2.0 lb/sec of water alone produced an increase in thrust of 35.8% of rate engine conditions and kerosene produced a negligible increase in thrust. Carbon dioxide increased thrust 23.5 percent.

Direct thrust measurement of a permanent magnet helicon double layer thruster

DOE Office of Scientific and Technical Information (OSTI.GOV)

Takahashi, K.; Lafleur, T.; Charles, C.

2011-04-04

Direct thrust measurements of a permanent magnet helicon double layer thruster have been made using a pendulum thrust balance and a high sensitivity laser displacement sensor. At the low pressures used (0.08 Pa) an ion beam is detected downstream of the thruster exit, and a maximum thrust force of about 3 mN is measured for argon with an rf input power of about 700 W. The measured thrust is proportional to the upstream plasma density and is in good agreement with the theoretical thrust based on the maximum upstream electron pressure.

Oxygen/Alcohol Dual Thrust RCS Engines

NASA Technical Reports Server (NTRS)

Angstadt, Tara; Hurlbert, Eric

1999-01-01

A non-toxic dual thrust RCS engine offers significant operational, safety, and performance advantages to the space shuttle and the next generation RLVs. In this concept, a single engine produces two thrust levels of 25 and 870 lbf. The low thrust level is provided by the spark torch igniter, which, with the addition of 2 extra valves, can also be made to function as a vernier. A dual thrust RCS engine allows 38 verniers to be packaged more efficiently on a vehicle. These 38 vemiers improve translation and reduce cross coupling, thereby providing more pure roll, pitch, and yaw maneuvers of the vehicle. Compared to the 6 vemiers currently on the shuttle, the 38 dual thrust engines would be 25 to 40% more efficient for the same maneuvers and attitude control. The vernier thrust level also reduces plume impingement and contamination concerns. Redundancy is also improved, thereby improving mission success reliability. Oxygen and ethanol are benign propellants which do not create explosive reaction products or contamination, as compared to hypergolic propellants. These characteristics make dual-thrust engines simpler to implement on a non-toxic reaction control system. Tests at WSTF in August 1999 demonstrated a dual-thrust concept that is successful with oxygen and ethanol. Over a variety of inlet pressures and mixture ratios at 22:1 area ratio, the engine produced between 230 and 297 sec Isp, and thrust levels from 8 lbf. to 50 lbf. This paper describes the benefits of dual-thrust engines and the recent results from tests at WSTF.

Emplacement history of a thrust sheet based on analysis of pressure solution cleavage and deformed fossils

DOE Office of Scientific and Technical Information (OSTI.GOV)

Protzman, G.M.; Mitra, G.

The emplacement history of a thrust sheet is recorded by the strain accumulated in its hanging wall and footwall. Detailed studies of second order structures and analysis of strain due to pressure solution and plastic deformation allow the authors to determine the deformation history of the Meade thrust in the Idaho - Wyoming thrust belt. Emplacement of the Meade thrust was accompanied by the formation of a series of second order in echelon folds in the footwall. Temporal relations based on detailed structural studies show that these folds, which are confined to the Jurassic Twin Creek Formation, formed progressively inmore » front of the advancing Meade thrust and were successively truncated and overridden by footwall imbricates of the Meade thrust. The Twin Creek Formation in both the hanging wall and footwall of the Meade thrust is penetratively deformed, with a well developed pressure solution cleavage. In addition, plastic strain is recorded by deformed Pentacrinus within fossil hash layers in the Twin Creek. Much of this penetrative deformation took place early in the history of the thrust sheet as layer parallel shortening, and the cleavage and deformed fossils behaved passively during subsequent folding and faulting. The later stages of deformation may be sequentially removed through balancing techniques to track successive steps in the deformation. This strain history, which is typical of an internal thrust sheet, is partly controlled by the lithologies involved, timing between successive thrusts, and the amount of interaction between major faults.« less

Why do airlines want and use thrust reversers? A compilation of airline industry responses to a survey regarding the use of thrust reversers on commercial transport airplanes

NASA Technical Reports Server (NTRS)

Yetter, Jeffrey A.

1995-01-01

Although thrust reversers are used for only a fraction of the airplane operating time, their impact on nacelle design, weight, airplane cruise performance, and overall airplane operating and maintenance expenses is significant. Why then do the airlines want and use thrust reversers? In an effort to understand the airlines need for thrust reversers, a survey of the airline industry was made to determine why and under what situations thrust reversers are currently used or thought to be needed. The survey was intended to help establish the cost/benefits trades for the use of thrust reversers and airline opinion regarding alternative deceleration devices. A compilation and summary of the responses given to the survey questionnaire is presented.

Thrust distribution for attitude control in a variable thrust propulsion system with four ACS nozzles

NASA Astrophysics Data System (ADS)

Lim, Yeerang; Lee, Wonsuk; Bang, Hyochoong; Lee, Hosung

2017-04-01

A thrust distribution approach is proposed in this paper for a variable thrust solid propulsion system with an attitude control system (ACS) that uses a reduced number of nozzles for a three-axis attitude maneuver. Although a conventional variable thrust solid propulsion system needs six ACS nozzles, this paper proposes a thrust system with four ACS nozzles to reduce the complexity and mass of the system. The performance of the new system was analyzed with numerical simulations, and the results show that the performance of the system with four ACS nozzles was similar to the original system while the mass of the whole system was simultaneously reduced. Moreover, a feasibility analysis was performed to determine whether a thrust system with three ACS nozzles is possible.

Optimal thrust level for orbit insertion

NASA Astrophysics Data System (ADS)

Cerf, Max

2017-07-01

The minimum-fuel orbital transfer is analyzed in the case of a launcher upper stage using a constantly thrusting engine. The thrust level is assumed to be constant and its value is optimized together with the thrust direction. A closed-loop solution for the thrust direction is derived from the extremal analysis for a planar orbital transfer. The optimal control problem reduces to two unknowns, namely the thrust level and the final time. Guessing and propagating the costates is no longer necessary and the optimal trajectory is easily found from a rough initialization. On the other hand the initial costates are assessed analytically from the initial conditions and they can be used as initial guess for transfers at different thrust levels. The method is exemplified on a launcher upper stage targeting a geostationary transfer orbit.

Northward laramide thrusting in the quitovac region, northwestern sonora, mexico: Implications for the juxtaposition of paleoproterozoic basement blocks and the mojave-sonora megashear hypothesis

USGS Publications Warehouse

Iriondo, Alexander; Martínez-Torres, Luis M.; Kunk, Michael J.; Atkinson, William W.; Premo, Wayne R.; McIntosh, William C.

2005-01-01

Restoration of 12%–30% Basin and Range extension allows direct interpretation of ductile fabrics associated with a stack of Laramide thrust faults in the Quitovac region in northwestern Sonora. The inferred direction of displacement of these thrusts varies gradually from N63°W to N23°E and is interpreted to represent a clockwise rotation of the direction of Laramide thrusting through time. The thrust faults represent a piggy-back sequence of thrusting propagating north, toward the foreland. The average direction and sense of displacement of the thrusts is N18°W, and the cumulative 45 km of estimated northward-directed displacement corresponds to ∼86% of shortening.Based on geochronological constraints, onset of thrusting in Quitovac occurred sometime between 75 and 61 Ma, whereas cessation occurred at ca. 39 Ma. The presence of Paleocene-Eocene orogenic gold mineralization, spatially associated with thrusting, strengthens our idea that compressional tectonism associated with the Laramide orogeny is a very important and widespread dynamometamorphic event in the region.Similarities in age, kinematics, and structural stratigraphy indicate that the thrusting in the Quitovac region may be equivalent to the Laramide Quitobaquito Thrust in southwestern Arizona. In both areas, thrust faults juxtapose the Paleoproterozoic Caborca and “North America” basement blocks. This juxtaposition was previously proposed as exclusively related to movements along the hypothetical Upper Jurassic Mojave-Sonora megashear. The Laramide northward displacements and clockwise rotations recorded in the Caborca block rocks in Quitovac contradict the southward displacements (∼800 km) and counterclockwise rotations inherent in the left-lateral Upper Jurassic Mojave-Sonora megashear hypothesis. We conclude that if this megashear exists in northwestern Sonora, its trace should be to the southwest of the Quitovac region.

From orogenic buildup to extensional unroofing: the evolution of the Adria - Europe collisional zone in the Medvednica Mountains of Croatia

NASA Astrophysics Data System (ADS)

Beniest, Anouk; van Gelder, Inge; Matenco, Liviu; Willingshofer, Ernst; Gruic, Andrea; Tomljenovic, Bruno

2013-04-01

Quantifying the kinematics of the Miocene extension in the Pannonian Basin is of critical importance for understanding the evolution of Adria-Europe collision in particular in the transitional zone from the Alps (Adria the upper plate) to the Dinarides (Adria the lower plate). Recent studies have demonstrated that large-scale extensional unroofing and core-complex formation affected the Europe-Adria contact in the Dinarides during Miocene times. The relationship between this extensional exhumation of Adriatic units and the roughly coeval Miocene extension affecting the Alpine-derived units during their E-ward extrusion into the intra-Carpathians ALCAPA block and the formation of the Pannonian basin is still unknown. One key area situated in the transitional zone is the Medvednica Mountains of Croatia, an area that benefits from already existing and extensive petrological and structural studies. The area of the Medvednica Mountains has been targeted by the means of a field kinematic analysis complemented by low-temperature thermochronology, metamorphic petrology and sedimentological observations. The results demonstrate that two units, reflecting distinct Adriatic paleogeographical positions, make up the structural geometry of the mountains. The upper unit contains Paleozoic mostly fine clastic sequence metamorphosed in sub-greenschist facies, overlain by a proximal Adriatic facies consisting of Triassic shallow water carbonates. The lower unit is made up by a volcanic sequence overlain by gradual deepening Triassic carbonates metamorphosed in greenschist facies that bears a strong resemblance to the Triassic break-up volcanism and subsequent sedimentation affecting the distal Adriatic units observed elsewhere in the Jadar-Kopaonik unit of the Dinarides. The strong contrast between the Middle-Upper Triassic facies suggests large scale thrusting during Cretaceous nappe stacking. Subsequently, the studied area has been affected by significant extensional deformation creating the present-day turtleback geometry. This resulted in the formation of brittle normal faults in both units, locally tilted by the uplift of the mountain core, which indicate mostly NE-SW extension. The lower unit is affected by a pervasive deformation characterized by a wide mylonitic shear zone with stretching lineations indicating consistently top-NE to E sense of shear. The present-day structural geometry of the mountains was established during the Pliocene-Quaternary inversion. The exact ages of nappe-stacking and subsequent extensional exhumation will be clarified by the upcoming low-temperature thermochronology and absolute age dating study. However, available results demonstrate that the extensional geometry and sense of shear is typical for the Miocene extensional exhumation and basin formation that affected the Adria-Europe contact elsewhere in the Dinarids, e.g. Kozara-Prosara-Motajica and Fruska Gora extensional structures. By comparing similar extensional features observed in for instance the Rechnitz and Pohorje extensional structures, the combined study potentially demonstrates that the Miocene mechanism of extension and sense of shear is structurally coherent at the scale of the entire Dinaridic and Alpine margins.

Thrust rollers

NASA Technical Reports Server (NTRS)

Vranish, John M. (Inventor)

2007-01-01

A thrust roller bearing system comprising an inner rotating member, an outer rotating member and multiple rollers coupling the inner rotating member with outer rotating member. The inner and outer rotating members include thrust lips to enable the rollers to act as thrust rollers. The rollers contact inner and outer rotating members at bearing contact points along a contact line. Consequently, the radial/tilt and thrust forces move synchronously and simultaneously to create a bearing action with no slipping.

Thrust Measurements of an Underexpanded Orifice in the Transitional Regime

NASA Astrophysics Data System (ADS)

Ketsdever, Andrew D.

2003-05-01

The popularity of micropropulsion system development has led to renewed interest in the determination of propulsive properties of orifice flows since micronozzle expansions may suffer high viscous losses at low pressure operation. The mass flow and relative thrust for an under expanded orifice is measured as a function of orifice stagnation pressure from 0.1 to 3.5 Torr. Nitrogen, argon, and helium propellant gases are passed through a 1.0 mm diameter orifice with a wall thickness of 0.015 mm . Near-free molecule, transitional and continuum flow regimes are studied. The relative thrust is determined by a novel thrust stand designed primarily for low operating pressure, micropropulsion systems. It is shown that the thrust indications obtained from the stand are a function of the facility background pressure, and corrections are made to determine the indicated thrust for a zero background pressure with nitrogen as propellant. Highly repeatable (within 1 %) indicated thrust measurements are obtained in the thrust range from 5 to 500 μN.

Back-thrusting in Lesser Himalaya: Evidences from magnetic fabric studies in parts of Almora crystalline zone, Kumaun Lesser Himalaya

NASA Astrophysics Data System (ADS)

Agarwal, Amar; Agarwal, K. K.; Bali, R.; Prakash, Chandra; Joshi, Gaurav

2016-06-01

The present study aims to understand evolution of the Lesser Himalaya, which consists of (meta) sedimentary and crystalline rocks. Field studies, microscopic and rock magnetic investigations have been carried out on the rocks near the South Almora Thrust (SAT) and the North Almora Thrust (NAT), which separates the Almora Crystalline Zone (ACZ) from the Lesser Himalayan sequences (LHS). The results show that along the South Almora Thrust, the deformation is persistent; however, near the NAT deformation pattern is complex and implies overprinting of original shear sense by a younger deformational event. We attribute this overprinting to late stage back-thrusting along NAT, active after the emplacement of ACZ. During this late stage back-thrusting, rocks of the ACZ and LHS were coupled. Back-thrusts originated below the Lesser Himalayan rocks, probably from the Main Boundary Thrust, and propagated across the sedimentary and crystalline rocks. This study provides new results from multiple investigations, and enhances our understanding of the evolution of the ACZ.

The immature thrust belt of the northern front of the Tianshan

NASA Astrophysics Data System (ADS)

Chen, Ke; Gumiaux, Charles; Augier, Romain; Chen, Yan; Wang, Qingchen

2010-05-01

The modern Tianshan (central Asia), which extends east-west on about 2500 km long with an average of more than 2000 m in altitude, is considered as a direct consequence of the reactivation of a Paleozoic belt due to the India - Asia collision. At first order, the finite structure of this range obviously displays a significant uprising of Paleozoic "basement" rocks - as a crustal-scale ‘pop-up' - surrounded by two Cenozoic foreland basins. In order to characterize the coupling history of this Cenozoic orogeny with its northern foreland basin (Junggar basin), a detailed structural field work has been carried out on the northern piedmont of Tianshan. From Wusu to Urumqi, on about 250 km long, the thrusting of the Paleozoic basement on the Mesozoic or Cenozoic sedimentary series of the basin is remarkably exposed along several river valleys. In contrast, in other sections, the Triassic to Jurassic sedimentary series can be followed from the basin to the range where they unconformably overlie on the Carboniferous basement. These series are only gently folded along the "range front". These features imply that, at regional-scale, the Cenozoic reactivation of the Tianshan has not produced important deformation along its contact with the juxtaposed Junggar basin. The shortening ascribed to the Cenozoic intra-continental collision would either be localized in the range, mostly accommodated by reactivated Paleozoic structures or faults in the basement units, or in the distal parts of the Junggar basin, by folds and faults within the Cenozoic sedimentary series. Alternative hypothesis would be that the Tianshan uplift and the movements associated with along its northern front structures, which are traditionally assigned to its Cenozoic reactivation, might be reduced. Such characteristic significantly differs from other well-known orogenic ranges, such as the Canadian Rocky Mountains, the Appalachians, the Pyrenees which display highly folded foreland basins and thrust belts with rather well developed range front structures. This suggests that the Tianshan intra-continental range is rather "young" and still at a primary stage of its orogenic evolution. In other words, its front may be considered as an immature thrust belt. If considering the available tomographic data across the Tianshan, its actual uplift may probably be produced by an asymmetric intracontinental deformation mechanism, i.e. a deeper subduction of the Tarim plate below the Tianshan (to the south), with respect to the one of Junggar plate to the north of the range. Consequently, the Tianshan range offers an excellent natural laboratory to study the processes of the on-going orogeny-foreland basin coupling, ancient structures reactivation as well as initiation and development of range front structures.

The Mesozoic palaeo-relief and immature front belt of northern Tianshan

NASA Astrophysics Data System (ADS)

Chen, K.; Gumiaux, C.; Augier, R.; Chen, Y.; Wang, Q.

2012-04-01

The modern Tianshan (central Asia) extends east-west on about 2500 km long with an average of more than 2000 m in altitude. At first order, the finite structure of this range obviously displays a crust-scale 'pop-up' of Palaeozoic rocks surrounded by two Cenozoic foreland basins. Up to now, this range is regarded as a direct consequence of the Neogene to recent reactivation of a Palaeozoic belt due to the India - Asia collision. This study focuses on the structure of the northern front area of Tianshan and is mainly based on field structural works. In particular, relationships in between sedimentary cover and basement units allow discussing the tectonic and morphological evolution of the northern Tianshan during Mesozoic and Cenozoic times. The study area is about 250 km long, from Wusu to Urumqi, along the northern piedmont of the Tianshan. Continental sedimentary series of the basin as well as structure of the cover/basement interface can well be observed along several incised valleys. Sedimentological observations argue for a limited transport distance for Lower and Uppermost Jurassic deposits that are preserved within intra-mountainous basins or within the foreland basin, along the range front. Moreover, some of the studied geological sections show that Triassic to Jurassic sedimentary series can be continuously followed from the basin to the range where they unconformably overlie the Carboniferous basement. Such onlap type structures of the Jurassic series, on top of the Palaeozoic rock units, can also be observed at more local-scale (~a few 100 m). At different scales, our observations thus clearly evidence i) the existence of a substantial relief during Mesozoic times and ii) very limited deformation, after Mesozoic, along some segments of the northern range front. Yet, thrusting of the Palaeozoic basement on the Mesozoic or Cenozoic sedimentary series of the basin is also well exposed along some other river valleys. As a consequence, the northern front of Tianshan displays as very uncylindrical with rapid lateral transitions from one type to the other. This study shows that the Cenozoic reactivation of the Tianshan range has not yielded important deformation along its contact with the juxtaposed Junggar basin, into the studied segment. Besides, the topography of the current northern Tianshan area can not be considered as the unique consequence of Cenozoic reactivation. Finally, from a compilation of structural field observations with available seismic geophysical data, regional cross sections show only moderate shortening in the deformed belt of the northern piedmont of Tianshan. Structure of the fold-and-thrust belt looks controlled by several basement thrusts faults separating rigid blocks. This study suggests that the northern front of the intra-continental Tianshan range may be considered as an immature thrust belt and is still at an early developing stage of its orogenic evolution.

Spacing of Imbricated Thrust Faults and the Strength of Thrust-Belts and Accretionary Wedges

NASA Astrophysics Data System (ADS)

Ito, G.; Regensburger, P. V.; Moore, G. F.

2017-12-01

The pattern of imbricated thrust blocks is a prominent characteristic of the large-scale structure of thrust-belts and accretionary wedges around the world. Mechanical models of these systems have a rich history from laboratory analogs, and more recently from computational simulations, most of which, qualitatively reproduce the regular patterns of imbricated thrusts seen in nature. Despite the prevalence of these patterns in nature and in models, our knowledge of what controls the spacing of the thrusts remains immature at best. We tackle this problem using a finite difference, particle-in-cell method that simulates visco-elastic-plastic deformation with a Mohr-Coulomb brittle failure criterion. The model simulates a horizontal base that moves toward a rigid vertical backstop, carrying with it an overlying layer of crust. The crustal layer has a greater frictional strength than the base, is cohesive, and is initially uniform in thickness. As the layer contracts, a series of thrust blocks immerge sequentially and form a wedge having a mean taper consistent with that predicted by a noncohesive, critical Coulomb wedge. The widths of the thrust blocks (or spacing between adjacent thrusts) are greatest at the front of the wedge, tend to decrease with continued contraction, and then tend toward a pseudo-steady, minimum width. Numerous experiments show that the characteristic spacing of thrusts increases with the brittle strength of the wedge material (cohesion + friction) and decreases with increasing basal friction for low (<8°) taper angles. These relations are consistent with predictions of the elastic stresses forward of the frontal thrust and at what distance the differential stress exceeds the brittle threshold to form a new frontal thrust. Hence the characteristic spacing of the thrusts across the whole wedge is largely inherited at the very front of the wedge. Our aim is to develop scaling laws that will illuminate the basic physical processes controlling systems, as well as allow researchers to use observations of thrust spacing as an independent constraint on the brittle strength of wedges as well as their bases.

Experimental Study of an Axisymmetric Dual Throat Fluidic Thrust Vectoring Nozzle for Supersonic Aircraft Application

NASA Technical Reports Server (NTRS)

Flamm, Jeffrey D.; Deere, Karen A.; Mason, Mary L.; Berrier, Bobby L.; Johnson, Stuart K.

2007-01-01

An axisymmetric version of the Dual Throat Nozzle concept with a variable expansion ratio has been studied to determine the impacts on thrust vectoring and nozzle performance. The nozzle design, applicable to a supersonic aircraft, was guided using the unsteady Reynolds-averaged Navier-Stokes computational fluid dynamics code, PAB3D. The axisymmetric Dual Throat Nozzle concept was tested statically in the Jet Exit Test Facility at the NASA Langley Research Center. The nozzle geometric design variables included circumferential span of injection, cavity length, cavity convergence angle, and nozzle expansion ratio for conditions corresponding to take-off and landing, mid climb and cruise. Internal nozzle performance and thrust vectoring performance was determined for nozzle pressure ratios up to 10 with secondary injection rates up to 10 percent of the primary flow rate. The 60 degree span of injection generally performed better than the 90 degree span of injection using an equivalent injection area and number of holes, in agreement with computational results. For injection rates less than 7 percent, thrust vector angle for the 60 degree span of injection was 1.5 to 2 degrees higher than the 90 degree span of injection. Decreasing cavity length improved thrust ratio and discharge coefficient, but decreased thrust vector angle and thrust vectoring efficiency. Increasing cavity convergence angle from 20 to 30 degrees increased thrust vector angle by 1 degree over the range of injection rates tested, but adversely affected system thrust ratio and discharge coefficient. The dual throat nozzle concept generated the best thrust vectoring performance with an expansion ratio of 1.0 (a cavity in between two equal minimum areas). The variable expansion ratio geometry did not provide the expected improvements in discharge coefficient and system thrust ratio throughout the flight envelope of typical a supersonic aircraft. At mid-climb and cruise conditions, the variable geometry design compromised thrust vector angle achieved, but some thrust vector control would be available, potentially for aircraft trim. The fixed area, expansion ratio of 1.0, Dual Throat Nozzle provided the best overall compromise for thrust vectoring and nozzle internal performance over the range of NPR tested compared to the variable geometry Dual Throat Nozzle.

Optimal Trajectories For Orbital Transfers Using Low And Medium Thrust Propulsion Systems

NASA Technical Reports Server (NTRS)

Cobb, Shannon S.

1992-01-01

For many problems it is reasonable to expect that the minimum time solution is also the minimum fuel solution. However, if one allows the propulsion system to be turned off and back on, it is clear that these two solutions may differ. In general, high thrust transfers resemble the well-known impulsive transfers where the burn arcs are of very short duration. The low and medium thrust transfers differ in that their thrust acceleration levels yield longer burn arcs which will require more revolutions, thus making the low thrust transfer computational intensive. Here, we consider optimal low and medium thrust orbital transfers.

Aircraft Engine Thrust Estimator Design Based on GSA-LSSVM

NASA Astrophysics Data System (ADS)

Sheng, Hanlin; Zhang, Tianhong

2017-08-01

In view of the necessity of highly precise and reliable thrust estimator to achieve direct thrust control of aircraft engine, based on support vector regression (SVR), as well as least square support vector machine (LSSVM) and a new optimization algorithm - gravitational search algorithm (GSA), by performing integrated modelling and parameter optimization, a GSA-LSSVM-based thrust estimator design solution is proposed. The results show that compared to particle swarm optimization (PSO) algorithm, GSA can find unknown optimization parameter better and enables the model developed with better prediction and generalization ability. The model can better predict aircraft engine thrust and thus fulfills the need of direct thrust control of aircraft engine.

Space Shuttle booster thrust imbalance analysis

NASA Technical Reports Server (NTRS)

Bailey, W. R.; Blackwell, D. L.

1985-01-01

An analysis of the Shuttle SRM thrust imbalance during the steady-state and tailoff portions of the boost phase of flight are presented. Results from flights STS-1 through STS-13 are included. A statistical analysis of the observed thrust imbalance data is presented. A 3 sigma thrust imbalance history versus time was generated from the observed data and is compared to the vehicle design requirements. The effect on Shuttle thrust imbalance from the use of replacement SRM segments is predicted. Comparisons of observed thrust imbalances with respect to predicted imbalances are presented for the two space shuttle flights which used replacement aft segments (STS-9 and STS-13).

Episodic growth of fold-thrust belts: Insights from Finite Element Modelling

NASA Astrophysics Data System (ADS)

Yang, Xiaodong; Peel, Frank J.; Sanderson, David J.; McNeill, Lisa C.

2017-09-01

The sequential development of a fold-thrust belt was investigated using 2D Finite Element Modelling (FEM). The new model results show that a thrust system is typically composed of three distinct regions: the thrust wedge, pre-wedge, and undeformed region. The thrust wedge involves growth that repeats episodically and cyclically. A cycle of wedge building starts as frontal accretion occurs, which is accompanied by a rapid increase in wedge width reducing the taper angle below critical. In response to this, the wedge interior (tracked here by the 50 m displacement position) rapidly propagates forwards into a region of incipient folding. The taper angle progressively increases until it obtains a constant apparent critical value (∼10°). During this period, the wedge experiences significant shortening after a new thrust initiates at the failure front, leading to a decrease in wedge width. Successive widening of the wedge and subsequent shortening and thrusting maintain a reasonably constant taper angle. The fold-thrust belt evolves cyclically, through a combination of rapid advancement of the wedge and subsequent gradual, slow wedge growth. The new model results also highlights that there is clear, although minor, deformation (0-10 m horizontal displacement) in front of the thrust wedge.

An Experimental Investigation of Unsteady Thrust Augmentation Using a Speaker-Driven Jet

NASA Technical Reports Server (NTRS)

Paxson, Daniel E.; Wernet, Mark P.; John, Wentworth T.

2004-01-01

An experimental investigation is described in which a simple speaker-driven jet was used as a pulsed thrust source (driver) for an ejector configuration. The objectives of the investigation were twofold: first, to add to the experimental body of evidence showing that an unsteady thrust source, combined with a properly sized ejector generally yields higher thrust augmentation values than a similarly sized, steady driver of equivalent thrust. Second, to identify characteristics of the unsteady driver that may be useful for sizing ejectors, and predicting what thrust augmentation values may be achieved. The speaker-driven jet provided a convenient source for the investigation because it is entirely unsteady (having no mean component) and because relevant parameters such as frequency, time-averaged thrust, and diameter are easily variable. The experimental setup will be described, as will the various measurements made. These include both thrust and Digital Particle Imaging Velocimetry of the driver. It will be shown that thrust augmentation values as high as 1.8 were obtained, that the diameter of the best ejector scaled with the dimensions of the emitted vortex, and that the so-called Formation Number serves as a useful dimensionless number by which to characterize the jet and predict performance.

Target thrust measurement for applied-field magnetoplasmadynamic thruster

NASA Astrophysics Data System (ADS)

Wang, B.; Yang, W.; Tang, H.; Li, Z.; Kitaeva, A.; Chen, Z.; Cao, J.; Herdrich, G.; Zhang, K.

2018-07-01

In this paper, we present a flat target thrust stand which is designed to measure the thrust of a steady-state applied-field magnetoplasmadynamic thruster (AF-MPDT). In our experiments we varied target-thruster distances and target size to analyze their influence on the target thrust measurement results. The obtained thrust-distance curves increase to local maximum and then decreases with the increasing distance, which means that the plume of the AF-MPDT can still accelerate outside the thruster exit. The peak positions are related to the target sizes: larger targets can make the peak positions further from the thruster and decrease the measurement errors. To further improve the reliability of measurement results, a thermal equilibrium assumption combined with Knudsen’s cosine law is adapted to analyze the error caused by the back stream of plume particles. Under the assumption, the error caused by particle backflow is no more than 3.6% and the largest difference between the measured thrust and the theoretical thrust is 14%. Moreover, it was verified that target thrust measurement can disturb the working of the AF-MPD thruster, and the influence on the thrust measurement result is no more than 1% in our experiment.

Laser Plasma Microthruster Performance Evaluation

NASA Astrophysics Data System (ADS)

Luke, James R.; Phipps, Claude R.

2003-05-01

The micro laser plasma thruster (μLPT) is a sub-kilogram thruster that is capable of meeting the Air Force requirements for the Attitude Control System on a 100-kg class small satellite. The μLPT uses one or more 4W diode lasers to ablate a solid fuel, producing a jet of hot gas or plasma which creates thrust with a high thrust/power ratio. A pre-prototype continuous thrust experiment has been constructed and tested. The continuous thrust experiment uses a 505 mm long continuous loop fuel tape, which consists of a black laser-absorbing fuel material on a transparent plastic substrate. When the laser is operated continuously, the exhaust plume and thrust vector are steered in the direction of the tape motion. Thrust steering can be avoided by pulsing the laser. A torsion pendulum thrust stand has been constructed and calibrated. Many fuel materials and substrates have been tested. Best performance from a non-energetic fuel material was obtained with black polyvinyl chloride (PVC), which produced an average of 70 μN thrust and coupling coefficient (Cm) of 190 μN/W. A proprietary energetic material was also tested, in which the laser initiates a non-propagating detonation. This material produced 500 μN of thrust.

The paradox of vertical σ2 in foreland fold and thrust belts

NASA Astrophysics Data System (ADS)

Tavani, Stefano

2014-05-01

Occurrence of aesthetically appealing thrust systems and associated large scale anticlines, in both active and fossil foreland fold and thrust belts, is commonly interpreted as an evidence for Andersonian compressional framework. Indeed, these structures would testify for a roughly vertical σ3. Such a correlation between thrusts occurrence and stress field orientation, however, frequently fails to explain denser observations at a smaller scale. The syn-orogenic deformation meso-structures hosted in exposed km-scale thrust-related folds, in fact, frequently and paradoxically witness for a syn-thrusting strike-slip stress configuration, with a near-vertical σ2 and a sub-horizontal σ3. This apparent widespread inconsistency between syn-orogenic meso-structures and stress field orientation is here named "the σ2 paradox". A possible explanation for such a paradox is provided by inherited extensional deformation structures commonly developed prior to thrusting, in the flexural foreland basins located ahead of fold and thrust belts. Thrust nucleation and propagation is facilitated and driven by the positive inversion of the extensional inheritances, and their subsequent linkage. This process eventually leads to the development of large reverse fault zones and can occur both in compressive and strike-slip stress configurations.

Deformation of Fold-and-Thrust Belts above a Viscous Detachment: New Insights from Analogue Modelling Experiments

NASA Astrophysics Data System (ADS)

Nogueira, Carlos R.; Marques, Fernando O.

2015-04-01

Theoretical and experimental studies on fold-and-thrusts belts (FTB) have shown that, under Coulomb conditions, deformation of brittle thrust wedges above a dry frictional basal contact is characterized by dominant frontward vergent thrusts (forethrusts) with thrust spacing and taper angle being directly influenced by the basal strength (increase in basal strength leading to narrower thrust spacing and higher taper angles); whereas thrust wedges deformed above a weak viscous detachment, such as salt, show a more symmetric thrust style (no prevailing vergence of thrusting) with wider thrust spacing and shallower wedges. However, different deformation patterns can be found on this last group of thrust wedges both in nature and experimentally. Therefore we focused on the strength (friction) of the wedge basal contact, the basal detachment. We used a parallelepiped box with four fixed walls and one mobile that worked as a vertical piston drove by a computer controlled stepping motor. Fine dry sand was used as the analogue of brittle rocks and silicone putty (PDMS) with Newtonian behaviour as analogue of the weak viscous detachment. To investigate the strength of basal contact on thrust wedge deformation, two configurations were used: 1) a horizontal sand pack with a dry frictional basal contact; and 2) a horizontal sand pack above a horizontal PDMS layer, acting as a basal weak viscous contact. Results of the experiments show that: the model with a dry frictional basal detachment support the predictions for the Coulomb wedges, showing a narrow wedge with dominant frontward vergence of thrusting, close spacing between FTs and high taper angle. The model with a weak viscous frictional basal detachment show that: 1) forethrusts (FT) are dominant showing clearly an imbricate asymmetric geometry, with wider spaced thrusts than the dry frictional basal model; 2) after FT initiation, the movement on the thrust can last up to 15% model shortening, leading to great amount of displacement along the FT; 3) intermittent reactivation of FTs also occurs despite the steepening of the FT plane and existence of new FT ahead, creating a high critical taper angle; 4) injection of PDMS from the basal weak layer into the FTs planes also favours to the long living of FTs and to the high critical taper angle; 5) vertical sand thickening in the hanging block also added to the taper angle.

14 CFR 25.934 - Turbojet engine thrust reverser system tests.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Turbojet engine thrust reverser system... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant General § 25.934 Turbojet engine thrust reverser system tests. Thrust reversers installed on turbojet engines must meet the...

Thrust reverser analysis for implementation in the Aviation Environmental Design Tool (AEDT)

DOT National Transportation Integrated Search

2007-06-01

This letter report presents an updated implementation for thrust reversers in AEDT. Currently, thrust reverser is applied to all STANDARD approach profiles in the Integrated Noise Mode (lNM) as 60% of the max rated thrust for jets and 40% for props o...

Kinematics and strain distribution of a thrust-related fold system in the Lewis thrust plate, northwestern Montana (U.S.A.)

NASA Astrophysics Data System (ADS)

Yin, An; Oertel, Gerhard

1993-06-01

In order to understand interactions between motion along thrusts and the associated style of deformation and strain distribution in their hangingwalls, geologic mapping and strain measurements were conducted in an excellently exposed thrust-related fold system in the Lewis thrust plate, northwestern Montana. This system consists of: (1) an E-directed basal thrust (the Gunsight thrust) that has a flat-ramp geometry and a slip of about 3.6 km; (2) an E-verging asymmetric anticline with its nearly vertical forelimb truncated by the basal thrust from below; (3) a 4-km wide fold belt, the frontal fold complex, that lies directly in front of the E-verging anticline; (4) a W-directed bedding-parallel fault (the Mount Thompson fault) that bounds the top of the frontal fold belt and separates it from the undeformed to broadly folded strata above; and (5) regionally developed, W-dipping spaced cleavage. Although the overall geometry of the thrust-related fold system differs from any previously documented fault-related folds, the E-verging anticline itself resembles geometrically a Rich-type fault-bend fold. The observed initial cut-off and fold interlimb angles of this anticline, however, cannot be explained by cross-section balancing models for the development of either a fault-bend fold or a fault propagation fold. Possible origins for the E-verging anticline include (1) the fold initiated as an open fault-bend fold and tightened only later during its emplacement along the basal thrust and (2) the fold started as either a fault-bend or a fault-propagation fold, but simultaneous or subsequent volume change incompatible with any balanced cross-section models altered its shape. Strain in the thrust-related fold system was determined by the preferred orientation of mica and chlorite grains. The direction and magnitude of the post-compaction strain varies from place to place. Strains in the foreclimb of the hangingwall anticline imply bedding-parallel thinning at some localities and thickening at others. This inhomogeneity may be caused by the development of thrusts and folds. Strain in the backlimb of the hangingwall anticline implies bedding-parallel stretching in the thrust transport direction. This could be the effect of bending as the E-verging anticline was tightened and transported across the basal thrust ramp. Strain measured next to the Gunsight thrust again indicates locally varying shortening and extension in the transport direction, perhaps in response to inhomogeneous friction on the fault or else to a history of alternating strain hardening and softening in the basal thrust zone.

Experimental results for a two-dimensional supersonic inlet used as a thrust deflecting nozzle

NASA Technical Reports Server (NTRS)

Johns, Albert L.; Burstadt, Paul L.

1984-01-01

Nearly all supersonic V/STOL aircraft concepts are dependent on the thrust deflecting capability of a nozzle. In one unique concept, referred to as the reverse flow dual fan, not only is there a thrust deflecting nozzle for the fan and core engine exit flow, but because of the way the propulsion system operates during vertical takeoff and landing, the supersonic inlet is also used as a thrust deflecting nozzle. This paper presents results of an experimental study to evaluate the performance of a supersonic inlet used as a thrust deflecting nozzle for this reverse flow dual fan concept. Results are presented in terms of nozzle thrust coefficient and thrust vector angle for a number of inlet/nozzle configurations. Flow visualization and nozzle exit flow survey results are also shown.

Varus Thrust and Knee Frontal Plane Dynamic Motion in Persons with Knee Osteoarthritis

PubMed Central

Chang, Alison H.; Chmiel, Joan S.; Moisio, Kirsten C.; Almagor, Orit; Zhang, Yunhui; Cahue, September; Sharma, Leena

2013-01-01

Objective Varus thrust visualized during walking is associated with a greater medial knee and an increased risk of medial knee osteoarthritis (OA) progression. Little is known about varus thrust presence determined by visual observation relates to quantitative gait kinematic We hypothesized that varus thrust presence is associated with greater knee frontal plane dynamic movement during the stance phase of gait. Methods Participants had knee OA in at least one knee. Trained examiners assessed participants for varus thrust presence during ambulation. Frontal plane knee motion during ambulation captured using external passive reflective markers and an 8-camera motion analysis system. To examine the cross-sectional relationship between varus thrust and frontal plane knee motion, used multivariable regression models with the quantitative motion measures as dependent variables and varus thrust (present/absent) as predictor; models were adjusted for age, gender, BMI, gait speed, and knee static alignment. Results 236 persons [mean BMI: 28.5 kg/m2 (SD 5.5), mean age: 64.9 years (SD 10.4), 75.8% women] contributing 440 knees comprised the study sample. 82 knees (18.6%) had definite varus thrust. Knees with varus thrust had greater peak varus angle and greater peak varus angular velocity during stance than knees without varus thrust (mean differences 0.90° and 6.65°/sec, respectively). These patterns remained significant after adjusting for age, gender, BMI, gait speed, and knee static alignment. Conclusion Visualized varus thrust during walking was associated with a greater peak knee varus angular velocity and a greater peak knee varus angle during stance phase of gait. PMID:23948980

Analysis of deformation bands in the Aztec Sandstone, Valley of Fire State Park, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hill, R.E.

1993-04-01

This research concerns two types of deformation structures, deformation bands and low-angle slip surfaces, that occur in the Aztec Sandstone in the Valley of Fire State Park, Nevada. Deformation bands were analyzed by mapping and describing over 500 of the structures on a bedding surface of about 560 square meters. Deformation bands are narrow zones of reduced porosity which form resistant ribs in the sandstone. Three sets of deformation bands are present at the study site (type 1,2, and 3). Type 1 and 2 bands are interpreted as coeval and form a conjugate set with a dihedral angle of 90more » degrees. These sets are usually composed of multiple bands. A third set is interpreted to be subsidiary to the older set, and intersections angles with the earlier formed sets are approximately 45 degrees. In contrast with the older sets, the third set is nearly always a single band which is sinuous or jagged along its length. All three sets of deformation bands are crosscut and sometimes offset by low-angle slip surfaces. These faults have reverse dip slip displacement and locally have mullions developed. Displacements indicate eastward movement of the hanging wall which is consistent with the inferred movements of major Mesozoic thrust faults in the vicinity. The change of deformation style from deformation bands to low-angle slip surfaces may document a change in the stress regime. Paleostress interpretation of the deformation band geometry indicates the intermediate stress axis is vertical. The low-angle slip surfaces indicate the least compressive stress axis is vertical. This possible change in stress axes may be the result of increasing pore pressure associated with tectonic loading from emplacement of the Muddy Mountain thrust.« less

Tertiary uplift of the Mt. Doonerak antiform, central Brooks Range, Alaska: Apatite fission track evidence from the Trans-Alaska Crustal Transect

USGS Publications Warehouse

O'Sullivan, P. B.; Moore, Thomas E.; Murphy, J.M.; Oldow, J.S.; Ave Lallemant, H.G.

1998-01-01

The Mt. Doonerak antiform is a northeast-trending, doubly plunging antiform located along the axial part of the central Brooks Range. This antiform is a crustal-scale duplex estimated to have a vertical displacement of ~15 km. The antiform folds the Amawk thrust, which separates relatively less displaced lower plate rocks in a window in the core of the antiform from allochthonous upper plate rocks of the Endicott Mountains allochthon. Because regional geological relations indicate that displacement on the Amawk thrust occurred between early Neocomian and early Albian time, uplift of the antiform is post-early Neocomian in age.Zircon fission-track data from the Mt. Doonerak antiform suggest -8-12 km of vertical denudation has occurred within the antiform region since -70-65 Ma. whereas apatite fission-track data indicate the antiform has experienced a minimum of -46 km of denudation since late Oligocene time. Following rapid denudation at -24 + 3 Ma, the rocks have experienced continued denudation to present surface conditions at a slower rate.We conclude from the relative relations and timing that the Mt. Doonerak duplex was constructed in part during the late Oligocene by reactivation of an older duplex formed during the latest Cretaceous to Paleocene. Deformation and uplift of Oligocene age for the axial part of the Brooks Range orogen is anomalously young, but it is the same age as the youngest episode of north-vergent contractional uplift in the northeastern Brooks Range. Because the Mt. Doonerak antiform displays structural characteristics similar to those of antiforms in the northeastern Brooks Range and because both regions experienced simultaneous rapid denudation, we suggest that the Mt. Doonerak antiform formed in response to an episode of contractional deformation that affected both areas in the late Oligocene.