Effect of Heat-Pressing Temperature and Holding Time on the Microstructure and Flexural Strength of Lithium Disilicate Glass-Ceramics

PubMed Central

Gao, Jing; Wang, Hui; Chen, Jihua

2015-01-01

The present study aimed to evaluate the influence of various heat-pressing procedures (different holding time and heat pressing temperature) on the microstructure and flexural strength of lithium disilicate glass ceramic. An experimental lithium silicate glass ceramic (ELDC) was prepared from the SiO2-Li2O-K2O-Al2O3-ZrO2-P2O5 system and heat-pressed following different procedures by varying temperature and holding time. The flexural strength was tested and microstructure was analyzed. The relationships between the microstructure, mechanical properties and heat-pressing procedures were discussed in-depth. Results verified the feasibility of the application of dental heat-pressing technique in processing the experimental lithium disilicate glass ceramic. Different heat-pressing procedures showed significant influence on microstructure and flexural strength. ELDC heat-pressed at 950℃ with holding time of 15 min achieved an almost pore-free microstructure and the highest flexural strength, which was suitable for dental restorative application. PMID:25985206

Motor experience with a sport-specific implement affects motor imagery

PubMed Central

Zhu, Hua; Shen, Cheng; Zhang, Jian

2018-01-01

The present study tested whether sport-specific implements facilitate motor imagery, whereas nonspecific implements disrupt motor imagery. We asked a group of basketball players (experts) and a group of healthy controls (novices) to physically perform (motor execution) and mentally simulate (motor imagery) basketball throws. Subjects produced motor imagery when they were holding a basketball, a volleyball, or nothing. Motor imagery performance was measured by temporal congruence, which is the correspondence between imagery and execution times estimated as (imagery time minus execution time) divided by (imagery time plus execution time), as well as the vividness of motor imagery. Results showed that experts produced greater temporal congruence and vividness of kinesthetic imagery while holding a basketball compared to when they were holding nothing, suggesting a facilitation effect from sport-specific implements. In contrast, experts produced lower temporal congruence and vividness of kinesthetic imagery while holding a volleyball compared to when they were holding nothing, suggesting the interference effect of nonspecific implements. Furthermore, we found a negative correlation between temporal congruence and the vividness of kinesthetic imagery in experts while holding a basketball. On the contrary, the implement manipulation did not modulate the temporal congruence of novices. Our findings suggest that motor representation in experts is built on motor experience associated with specific-implement use and thus was subjected to modulation of the implement held. We conclude that sport-specific implements facilitate motor imagery, whereas nonspecific implements could disrupt motor representation in experts. PMID:29719738

20 CFR 1002.41 - Does an employee have rights under USERRA even though he or she holds a temporary, part-time...

Code of Federal Regulations, 2010 CFR

2010-04-01

... even though he or she holds a temporary, part-time, probationary, or seasonal employment position? 1002... employee have rights under USERRA even though he or she holds a temporary, part-time, probationary, or seasonal employment position? USERRA rights are not diminished because an employee holds a temporary, part...

MO-FG-CAMPUS-JeP3-04: Feasibility Study of Real-Time Ultrasound Monitoring for Abdominal Stereotactic Body Radiation Therapy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Su, Lin; Kien Ng, Sook; Zhang, Ying

Purpose: Ultrasound is ideal for real-time monitoring in radiotherapy with high soft tissue contrast, non-ionization, portability, and cost effectiveness. Few studies investigated clinical application of real-time ultrasound monitoring for abdominal stereotactic body radiation therapy (SBRT). This study aims to demonstrate the feasibility of real-time monitoring of 3D target motion using 4D ultrasound. Methods: An ultrasound probe holding system was designed to allow clinician to freely move and lock ultrasound probe. For phantom study, an abdominal ultrasound phantom was secured on a 2D programmable respiratory motion stage. One side of the stage was elevated than another side to generate 3D motion.more » The motion stage made periodic breath-hold movement. Phantom movement tracked by infrared camera was considered as ground truth. For volunteer study three healthy subjects underwent the same setup for abdominal SBRT with active breath control (ABC). 4D ultrasound B-mode images were acquired for both phantom and volunteers for real-time monitoring. 10 breath-hold cycles were monitored for each experiment. For phantom, the target motion tracked by ultrasound was compared with motion tracked by infrared camera. For healthy volunteers, the reproducibility of ABC breath-hold was evaluated. Results: Volunteer study showed the ultrasound system fitted well to the clinical SBRT setup. The reproducibility for 10 breath-holds is less than 2 mm in three directions for all three volunteers. For phantom study the motion between inspiration and expiration captured by camera (ground truth) is 2.35±0.02 mm, 1.28±0.04 mm, 8.85±0.03 mm in LR, AP, SI directly, respectively. The motion monitored by ultrasound is 2.21±0.07 mm, 1.32±0.12mm, 9.10±0.08mm, respectively. The motion monitoring error in any direction is less than 0.5 mm. Conclusion: The volunteer study proved the clinical feasibility of real-time ultrasound monitoring for abdominal SBRT. The phantom and volunteer ABC studies demonstrated sub-millimeter accuracy of 3D motion movement monitoring.« less

Hyperbaric nitrogen prolongs breath-holding time in humans.

PubMed

Morooka, H; Wakasugi, Y; Shimamoto, H; Shibata, O; Sumikawa, K

2000-09-01

Either an increase in PaCO(2) or a decrease in PaO(2), can affect respiratory stimulation through respiratory centers, thus influencing breath-holding time (BHT). This study was designed to determine whether and how hyperbaric air could influence BHT in comparison with hyperbaric oxygen in humans. We studied 36 healthy volunteers in a multiplace hyperbaric chamber. BHT, pulse oximeter, and transcutaneous carbon dioxide tension were measured at 1 and 2.8 atmosphere absolute (ATA) in two groups. Group A (n = 20) breathed air. Group O (n = 16) breathed oxygen with a face mask (5 L/min). BHTs were 108 +/- 28 s at 1.0 ATA and 230 +/- 71 s at 2.8 ATA in Group A, and 137 +/- 48 s at 1.0 ATA and 180 +/- 52 s at 2.8 ATA in Group O. Transcutaneous carbon dioxide tension in Group A (59 +/- 2 mm Hg) was higher than that in Group O (54 +/- 2 mm Hg) at the end of maximal breath-holding at 2.8 ATA. The prolongation of BHT in hyperbaric air is significantly greater than that in hyperbaric oxygen. Breath-holding time is significantly prolonged in hyperbaric air than it is in hyperbaric oxygen. The mechanism involves the anesthetic effect of nitrogen suppressing the suffocating feeling during breath-holding.

Creep fatigue of low-cobalt superalloys: Waspalloy, PM U 700 and wrought U 700

NASA Technical Reports Server (NTRS)

Leis, B. N.; Rungta, R.; Hopper, A. T.

1983-01-01

The influence of cobalt content on the high temperature creep fatigue crack initiation resistance of three primary alloys was evaluated. These were Waspalloy, Powder U 700, and Cast U 700, with cobalt contents ranging from 0 up to 17 percent. Waspalloy was studied at 538 C whereas the U 700 was studied at 760 C. Constraints of the program required investigation at a single strain range using diametral strain control. The approach was phenomenological, using standard low cycle fatigue tests involving continuous cycling tension hold cycling, compression hold cycling, and symmetric hold cycling. Cycling in the absence of or between holds was done at 0.5 Hz, whereas holds when introduced lasted 1 minute. The plan was to allocate two specimens to the continuous cycling, and one specimen to each of the hold time conditions. Data was taken to document the nature of the cracking process, the deformation response, and the resistance to cyclic loading to the formation of small cracks and to specimen separation. The influence of cobalt content on creep fatigue resistance was not judged to be very significant based on the results generated. Specific conclusions were that the hold time history dependence of the resistance is as significant as the influence of cobalt content and increased cobalt content does not produce increased creep fatigue resistance on a one to one basis.

Microstructural Evolution and the Precipitation Behavior in X90 Linepipe Steel During Isothermal Processing

NASA Astrophysics Data System (ADS)

Tian, Y.; Wang, H. T.; Wang, Z. D.; Misra, R. D. K.; Wang, G. D.

2018-03-01

Thermomechanical controlled processing of 560-MPa (X90) linepipe steel was simulated in the laboratory using a thermomechanical simulator to study the microstructural evolution and precipitation behavior during isothermal holding. The results indicated that martensite was obtained when the steels were isothermally held for 5 s at 700 °C. Subsequently, granular bainite and acicular ferrite transformation occurred with increased holding time. Different amount of polygonal ferrite formed after isothermally holding for 600-3600 s. Pearlite nucleated after isothermally holding for 3600 s. Precipitation occurred after isothermal holding for 5 s and continuous precipitation occurred at grain boundaries after isothermally holding for 600 s. After isothermally holding for 3600 s, large Nb/Ti carbide precipitated. The presence of MX-type precipitates was confirmed by diffraction pattern. The interphase precipitation (IP) occurred between 5 and 30 s. Maximum hardness was obtained after isothermally holding for 600 s when IP occurred and rapidly decreased to a low value, mainly because polygonal ferrite dominated the microstructure after isothermally holding for 3600 s.

Effects of Sintering Holding Time on the Structural, Electrical and Magnetic Properties of Zn0.95Ni0.05O

NASA Astrophysics Data System (ADS)

Ginting, M.; Aryanto, D.; Kurniawan, C.; Sari, A. Y.; Subhan, A.; Sudiro, T.; Sebayang, P.; Tarigan, E. R.; Nasruddin, M. N.; Sebayang, K.

2017-05-01

Zn0.95Ni0.05O has been synthesized by mixing 5% mol of NiO into ZnO using solid state reaction and high-speed shaker mill method. The samples were sintered at 900 °C with holding time for 2, 4 and 8 hours. Crystal structure, electrical and magnetic properties of Zn0.95Ni0.05O were characterized by using XRD, I-V, C-V and VSM. XRD results showed that variation of holding time does not change the structure of ZnO and no other secondary phase observed. The value of lattice parameters (a and c) tends to decrease proportionally to the holding time. The Intensity value changes and the peak shifted to a higher 2θ angle due to holding time variation. In general, the conductance of Zn0.95Ni0.05O decreases and the magnetic properties decrease also as the holding time is increased.

Effects of tip-substrate gap, deposition temperature, holding time, and pull-off velocity on dip-pen lithography investigated using molecular dynamics simulation

NASA Astrophysics Data System (ADS)

Wu, Cheng-Da; Fang, Te-Hua; Lin, Jen-Fin

2012-05-01

The process parameters in the dip-pen nanolithography process, including tip-substrate gap, deposition temperature, holding time, and pull-off velocity are evaluated in terms of the mechanism of molecular transference, alkanethiol meniscus characteristic, surface adsorbed energy, and pattern formation using molecular dynamics simulations. The simulation results clearly show that the optimum deposition occurs at a smaller tip-substrate gap, a slower pull-off velocity, a higher temperature, and a longer holding time. The pattern area increases with decreasing tip-substrate gap and increasing deposition temperature and holding time. With an increase in deposition temperature, the molecular transfer ability significantly increases. Pattern height is a function of meniscus length. When the pull-off velocity is decreased, the pattern height increases. The height of the neck in meniscus decreases and the neck width increases with holding time. Meniscus size increases with increasing deposition temperature and holding time.

Optimization of ethylene glycol concentrations, freezing rates and holding times in liquid nitrogen vapor for cryopreservation of rhesus macaque (Macaca mulatta) sperm.

PubMed

Yang, Shihua; Ping, Shuhuang; Si, Wei; He, Xiechao; Wang, Xinyi; Lu, Yongqing; Ji, Shaohui; Niu, Yuyu; Ji, Weizhi

2011-06-01

Ethylene glycol (EG) has been speculated to be the most appropriate penetrating cryoprotectant for cryopreservation of rhesus macaque sperm due to its higher permeability coefficient. The present study aimed to determine the optimal EG concentration, freezing rate and holding time in liquid nitrogen (LN(2)) vapor for rhesus sperm cryopreservation. Among six tested EG concentrations (0, 0.18, 0.35, 0.7, 1.4 and 2.1 M), 0.7 M EG showed the most effective cryoprotection (P<0.05). Sperm frozen with 0.7 M EG at -183°C/min showed higher post-thaw motility than sperm frozen at -10, -67 or -435°C/min (P<0.05). Sperm frozen in LN(2) vapor at -183°C/min with 0.7 M EG and a holding time of 10 min showed higher post-thaw motility compared with a holding time of 5 or 15 min (P<0.05). The function of sperm cryopreserved at the optimized EG concentration, freezing rate and holding time was further evaluated by in vitro fertilization. Of the 36 oocytes collected from gonadotropin-stimulated rhesus macaques, 61.1% were fertilized, and 61.1, 44.4 and 36.1% of the oocytes developed to 2 cells, morulae and blastocysts, respectively. Our findings provide an alternative penetrating cryoprotectant and optimal protocol for genetic preservation purposes in this important species.

RE-EVALUATION OF APPLICABILITY OF AGENCY SAMPLE HOLDING TIMES

EPA Science Inventory

Purpose and Rationale:

1) To assess the validity of currently recognized holding times and to provide a scientific basis for changes that may be necessary to the current regulations.

2) While holding times may appear adequate to protect sample integrity and provid...

Educational Credentials in Australia: Average Positional Value in Decline. Centre for the Study of Higher Education Research Working Papers, 93.4.

ERIC Educational Resources Information Center

Marginson, Simon

Since the 1960s there has been a major expansion in the number of people in Australia holding post school educational credentials and the proportion of the full time work force with those credentials. The penalties of not holding credentials, in terms of the incidence and duration of unemployment, are increasingly severe. At the same time, there…

Effect of Camellia sinensis supplementation and increasing holding time on quality of cryopreserved boar semen.

PubMed

Gale, I; Gil, L; Malo, C; González, N; Martínez, F

2015-06-01

Cryopreservation of boar semen is still considered suboptimal due to the low fertility when compared with fresh semen. This study was performed to evaluate the effects of green tea (Camellia sinensis) supplementation of the freezing extender at different concentration (0, 2.5%, 5%, 10%) and also to determine the influence of increasing holding time from 2 to 24 h at 15 °C. Seventeen ejaculates from nine boars were used to make pools of three of them and then cryopreserved. Sperm motility, viability, acrosome integrity, membrane functionality (HOST) and capacitation status were determined before freezing and at 0, 30, 60, 90 and 120 min after thawing. Lipid peroxidation was evaluated just after thawing. The main findings emerging from this study were the following: (i) no improvement in quality of thawed spermatozoa with addition of tea to the freezing extender, (ii) no improvement in quality of thawed spermatozoa with prolonged holding time, (iii) lower peroxidation rate in presence of tea 5% and (iv) a decrease in the number of uncapacited viable spermatozoa with any tea supplementation. We conclude that amplification of holding time in semen cryopreservation process does not vary results, facilitating freezing protocol. Tea supplementation reduces lipoxidation but did not improve quality parameters. © 2014 Blackwell Verlag GmbH.

MERCURY CONCENTRATION IN FROZEN WHOLE-FISH HOMOGENATES IS INSENSITIVE TO HOLDING TIME

EPA Science Inventory

Current recommended holding times for the analysis of total mercury (Hg) in fish tissue ranges from 28 to 180 days. In 2006, we evaluated the effect of an extended holding time on Hg concentrations by reanalyzing whole-fish wet homogenates that were analyzed originally in 2002 an...

RE-EVALUATION OF APPLICABILITY OF AGENCY SAMPLE HOLDING TIMES

EPA Science Inventory

The Purpose and Rationale is to:

To assess the validity of currently recognized holding times and to provide a scientific basis for changes tha may be necessary to the current regulations.

While holding times may appear adequate to protect sample integrity and provi...

High-temperature low-cycle-fatigue and crack-growth behaviors of three superalloys: HASTELLOY X, HAYNES 230, and HAYNES 188

NASA Astrophysics Data System (ADS)

Lu, Yulin

Low cycle fatigue (LCF) and fatigue crack growth (FCG) experiments on three superalloys HASTELLOY X, HAYNES 230, and HAYNES 188 have been conducted at temperatures from 649 to 982°C. Hold times were imposed at the maximum strain or load to investigate the hold-time effect. In general, the fatigue life decreased as the temperature or hold time increased. However, for the HAYNES 230 alloy at total strain ranges higher than 1.0% and without a hold time, the LCF life was longer at 927°C than at 816°C. This "abnormal" behavior was found to result from the smaller plastic strain amplitude at half-life at 927°C than that at 816°C. An increase in the temperature and/or the introduction of a hold time decreased the hardening rate and increased the softening rate for all the three alloys. The introduction of a hold time and/or the increase of the test temperature progressively changed the fracture mode from the transgranular to mixed trans/inter-granular, then to intergranular feature. Within the two phases of the fatigue process, crack initiation was more severely influenced by the change of the hold time and/or temperature. The FCG data of HASTELLOY X and HAYNES 230 alloys were analyzed with an emphasis on hold-time and temperature effects. The crack grew faster at a higher temperature and a longer hold time. Fracture-mechanics parameters, C*, Ct, and (Ct)avg, were applied to correlate the crack-growth rates. The fatigue-cracking path was mainly transgranular at 816 and 927°C. The cracking path became dominantly intergranular if the hold time increased to 2 min, indicating that the time-dependent damage mechanisms were in control. The Ct and (Ct)avg parameters were capable of consolidating time dependent crack growth rate from different temperatures and alloys. The tests were conducted in air. Therefore, the fracture surfaces were frequently covered with a dark layer of oxides, making fracture feature difficult to identify under scanning-electron-microscopy. To overcome this problem, an oxide-stripping technique has been developed. The sample is first boiled in a potassium permanganate solution for 1 h, and then electrolytically cleaned in an alkaline solution for 5 min.

SU-F-P-30: Clinical Assessment of Auto Beam-Hold Triggered by Fiducial Localization During Prostate RapidArc Delivery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Atkinson, P; Chen, Q

2016-06-15

Purpose: To assess the clinical efficacy of auto beam hold during prostate RapidArc delivery, triggered by fiducial localization on kV imaging with a Varian True Beam. Methods: Prostate patients with four gold fiducials were candidates in this study. Daily setup was accomplished by aligning to fiducials using orthogonal kV imaging. During RapidArc delivery, a kV image was automatically acquired with a momentary beam hold every 60 degrees of gantry rotation. The position of each fiducial was identified by a search algorithm and compared to a predetermined 1.4 cm diameter target area. Treatment continued if all the fiducials were within themore » target area. If any fiducial was outside the target area the beam hold was not released, and the operators determined if the patient needed re-alignment using the daily setup method. Results: Four patients were initially selected. For three patients, the auto beam hold performed seamlessly. In one instance, the system correctly identified misaligned fiducials, stopped treatment, and the patient was re-positioned. The fourth patient had a prosthetic hip which sometimes blocked the fiducials and caused the fiducial search algorithm to fail. The auto beam hold was disabled for this patient and the therapists manually monitored the fiducial positions during treatment. Average delivery time for a 2-arc fraction was increased by 59 seconds. Phantom studies indicated the dose discrepancy related to multiple beam holds is <0.1%. For a plan with 43 fractions, the additional imaging increased dose by an estimated 68 cGy. Conclusion: Automated intrafraction kV imaging can effectively perform auto beam holds due to patient movement, with the exception of prosthetic hip patients. The additional imaging dose and delivery time are clinically acceptable. It may be a cost-effective alternative to Calypso in RapidArc prostate patient delivery. Further study is warranted to explore its feasibility under various clinical conditions.« less

Medicaid Bed-Hold Policy and Medicare Skilled Nursing Facility Rehospitalizations

PubMed Central

Grabowski, David C; Feng, Zhanlian; Intrator, Orna; Mor, Vincent

2010-01-01

Objective To analyze the effect of states' Medicaid bed-hold policies on the 30-day rehospitalization of Medicare postacute skilled nursing facility (SNF) residents. Data Sources Minimum data set assessments were merged with Medicare claims and eligibility files for all first-time SNF admissions (N = 3,322,088) over the period 2000 through 2005; states' Medicaid bed-hold policies were obtained via survey. Study Design Regression specification incorporating facility fixed effects to examine changes in Medicaid bed-hold policies on the likelihood of a 30-day SNF rehospitalization. Principal Findings Using a continuous measure of bed-hold generosity, state Medicaid bed-hold was positively related to Medicare SNF rehospitalization. Specifically, the introduction of a bed-hold policy with average generosity increases Medicare rehospitalizations by 1.8 percent, representing roughly 12,000 SNF rehospitalizations at a cost to Medicare of approximately U.S.$100 million over our study period. Conclusions Although facilities do not receive a Medicaid bed-hold payment for Medicare SNF stays, we found that the adoption of more generous policies led to greater SNF rehospitalizations. This type of spillover is largely ignored in current discussions of Medicare payment reforms such as bundled payment. Neither Medicare nor Medicaid has an incentive to internalize the risks and benefits of its actions as they affect the other. PMID:20403059

Acute Effects of Cannabis on Breath-Holding Duration

PubMed Central

Farris, Samantha G.; Metrik, Jane

2016-01-01

Distress intolerance (an individual’s perceived or actual inability to tolerate distressing psychological or physiological states) is associated with cannabis use. It is unknown whether a bio-behavioral index of distress intolerance, breath-holding duration, is acutely influenced (increased or decreased) by cannabis. Such information may further inform understanding of the expression of psychological or physiological distress post-cannabis use. This within-subjects study examined whether smoked marijuana with 2.7–3.0 % delta-9-tetrahydrocannabinol (THC), relative to placebo, acutely changed duration of breath-holding. Participants (n = 88; 65.9% male) were non-treatment seeking frequent cannabis users who smoked placebo or active THC cigarette on two separate study days and completed breath-holding task. Controlling for baseline breath-holding duration and participant sex, THC produced significantly lower breath-holding durations relative to placebo. There was a significant interaction of drug administration x frequency of cannabis use, such that THC decreased breath-holding time among less frequent but not among more frequent users. Findings indicate that cannabis may be exacerbating distress intolerance (via breath-holding duration). As compared to less frequent cannabis users, frequent users display tolerance to cannabis’ acute effects including increased ability to tolerate respiratory distress when holding breath. Objective measures of distress intolerance are sensitive to contextual factors such as acute drug intoxication, and may inform the link between cannabis use and the expression of psychological distress. PMID:27454678

Self-Verification Strivings in Children Holding Negative Self-Views: The Mitigating Effects of a Preceding Success Experience

PubMed Central

Thomaes, Sander; Kamphuis, Jan Henk; de Castro, Bram Orobio; Telch, Michael J.

2010-01-01

Research among adults has consistently shown that people holding negative self-views prefer negative over positive feedback. The present study tested the hypothesis that this preference is less robust among pre-adolescents, such that it will be mitigated by a preceding positive event. Pre-adolescents (n = 75) holding positive or negative global self-esteem were randomized to a favorable or unfavorable peer evaluation outcome. Next, preferences for positive versus negative feedback were assessed using an unobtrusive behavioral viewing time measure. As expected, results showed that after being faced with the success outcome children holding negative self-views were as likely as their peers holding positive self-views to display a significant preference for positive feedback. In contrast, children holding negative self-views displayed a stronger preference for negative feedback after being faced with the unfavorable outcome that matched their pre-existing self-views. PMID:21151482

Self-Verification Strivings in Children Holding Negative Self-Views: The Mitigating Effects of a Preceding Success Experience.

PubMed

Reijntjes, Albert; Thomaes, Sander; Kamphuis, Jan Henk; de Castro, Bram Orobio; Telch, Michael J

2010-12-01

Research among adults has consistently shown that people holding negative self-views prefer negative over positive feedback. The present study tested the hypothesis that this preference is less robust among pre-adolescents, such that it will be mitigated by a preceding positive event. Pre-adolescents (n = 75) holding positive or negative global self-esteem were randomized to a favorable or unfavorable peer evaluation outcome. Next, preferences for positive versus negative feedback were assessed using an unobtrusive behavioral viewing time measure. As expected, results showed that after being faced with the success outcome children holding negative self-views were as likely as their peers holding positive self-views to display a significant preference for positive feedback. In contrast, children holding negative self-views displayed a stronger preference for negative feedback after being faced with the unfavorable outcome that matched their pre-existing self-views.

Interpreting the Need for Initial Support to Perform Tandem Stance Tests of Balance

PubMed Central

Brach, Jennifer S.; Perera, Subashan; Wert, David M.; VanSwearingen, Jessie M.; Studenski, Stephanie A.

2012-01-01

Background Geriatric rehabilitation reimbursement increasingly requires documented deficits on standardized measures. Tandem stance performance can characterize balance, but protocols are not standardized. Objective The purpose of this study was to explore the impact of: (1) initial support to stabilize in position and (2) maximum hold time on tandem stance tests of balance in older adults. Design A cross-sectional secondary analysis of observational cohort data was conducted. Methods One hundred seventeen community-dwelling older adults (71% female, 12% black) were assigned to 1 of 3 groups based on the need for initial support to perform tandem stance: (1) unable even with support, (2) able only with support, and (3) able without support. The able without support group was further stratified on hold time in seconds: (1) <10 (low), (2) 10 to 29, (medium), and (3) 30 (high). Groups were compared on primary outcomes (gait speed, Timed “Up & Go” Test performance, and balance confidence) using analysis of variance. Results Twelve participants were unable to perform tandem stance, 14 performed tandem stance only with support, and 91 performed tandem stance without support. Compared with the able without support group, the able with support group had statistically or clinically worse performance and balance confidence. No significant differences were found between the able with support group and the unable even with support group on these same measures. Extending the hold time to 30 seconds in a protocol without initial support eliminated ceiling effects for 16% of the study sample. Limitations Small comparison groups, use of a secondary analysis, and lack of generalizability of results were limitations of the study. Conclusions Requiring initial support to stabilize in tandem stance appears to reflect meaningful deficits in balance-related mobility measures, so failing to consider support may inflate balance estimates and confound hold time comparisons. Additionally, 10-second maximum hold times limit discrimination of balance in adults with a higher level of function. For community-dwelling older adults, we recommend timing for at least 30 seconds and documenting initial support for consideration when interpreting performance. PMID:22745198

The mechanisms of flame holding in the wake of a bluff body

NASA Technical Reports Server (NTRS)

Strehlow, R. A.; Malik, S.

1984-01-01

The flame holding mechanism for lean methane and lean propane air flames is examined under conditions where the recirculation zone is absent. The holding process is studied in detail in an attempt to determine the mechanism of flame holding and also the conditions where this mechanism is viable and when it fails and blow off occurs. Inverted flames held in the wake of a flat strip are studied. The velocity flow field is determined using a Laser Doppler Velocimetry technique. Equation of continuity is used to calculate the flame temperature from the change in area of flow streamlines before and after the flame. For methane air flame the controlling factor for blow off is incomplete reaction due to higher blowing rate leading to reduced residence time in the reaction zone.

Progress Report on Long Hold Time Creep Fatigue of Alloy 617 at 850°C

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carroll, Laura Jill

Alloy 617 is the leading candidate material for an intermediate heat exchanger for the very high temperature reactor. To evaluate the behavior of this material in the expected service conditions, strain-controlled cyclic tests that include long hold times up to 240 minutes at maximum tensile strain were conducted at 850°C. In terms of the total number of cycles to failure, the fatigue resistance decreased when a hold time was added at peak tensile strain. Increases in the tensile hold duration degraded the creep-fatigue resistance, at least to the investigated strain controlled hold time of up to 60 minutes at themore » 0.3% strain range and 240 minutes at the 1.0% strain range. The creep-fatigue deformation mode is considered relative to the lack of saturation, or continually decreasing number of cycles to failure with increasing hold times. Additionally, preliminary values from the 850°C creep-fatigue data are calculated for the creep-fatigue damage diagram and have higher values of creep damage than those from tests at 950°C.« less

Performance Comparison of Al-Ti Master Alloys with Different Microstructures in Grain Refinement of Commercial Purity Aluminum.

PubMed

Ding, Wanwu; Xia, Tiandong; Zhao, Wenjun

2014-05-07

Three types of Al-5Ti master alloys were synthesized by a method of thermal explosion reaction in pure molten aluminum. Performance comparison of Al-5Ti master alloy in grain refinement of commercial purity Al with different additions (0.6%, 1.0%, 1.6%, 2.0%, and 3.0%) and holding time (10, 30, 60 and 120 min) were investigated. The results show that Al-5Ti master alloy with blocky TiAl₃ particles clearly has better refining efficiency than the master alloy with mixed TiAl₃ particles and the master alloy with needle-like TiAl₃ particles. The structures of master alloys, differing by sizes, morphologies and quantities of TiAl₃ crystals, were found to affect the pattern of the grain refining properties with the holding time. The grain refinement effect was revealed to reduce markedly for master alloys with needle-like TiAl₃ crystals and to show the further significant improvement at a longer holding time for the master alloy containing both larger needle-like and blocky TiAl₃ particles. For the master alloy with finer blocky particles, the grain refining effect did not obviously decrease during the whole studied range of the holding time.

Breath-holding times in various phases of respiration and effect of respiratory training in lung cancer patients.

PubMed

Tibdewal, Anil; Munshi, Anusheel; Pathak, Rima; Misra, Shagun; Daptardar, Anuradha; Singh, Vincent; Agarwal, Jai Prakash

2015-08-01

Breath-holding (BH) technique is used for reducing the intrafraction-tumour motion in mobile lung tumours treated with radiotherapy (RT). There is paucity of literature evaluating differences in BH times in various phases of respiration in patients with lung cancer. One hundred consecutive patients with lung cancer planned for radical RT/chemoradiation were accrued in the study. Eighty-seven patients were eligible for analysis at RT conclusion. Baseline pulmonary function test (PFT) were performed in all patients, and respiratory training was given from the day of RT planning. Deep inspiration breath hold (DIBH), deep expiration breath hold (DEBH) and mid-ventilation breath hold (MVBH) were recorded manually with a stopwatch for each patient at four time points (RT planning/baseline, RT starting, during RT and RT conclusion). Median DIBH times at RT planning, RT starting, during RT and RT conclusion were 21.2, 20.6, 20.1 and 21.1 s, respectively. The corresponding median DEBH and MVBH times were 16.3, 18.2, 18.3, 18.5 s and 19.9, 20.5, 21.3, 22.1 s, respectively. Respiratory training increased MVBH time at RT conclusion compared to baseline, which was statistically significant (19.9-22.1 s, P = 0.002). DIBH or DEBH times were stable at various time points with neither a significant improvement nor decline. Among various patient and tumour factors Forced Vital Capacity pre-bronchodilation (FVCpre ) was the only factor that consistently predicted DIBH, DEBH and MVBH at all four time points with P value <0.05. BH was well tolerated by most lung cancer patients with minimum median BH time of at least 16 s in any of the three phases of respiration. Respiratory training improved MVBH time while consistently maintaining DIBH and DEBH times throughout the course of radiotherapy. © 2015 The Royal Australian and New Zealand College of Radiologists.

C-14/I-29 Preservation and Hold Time Survey

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kitchen, S.

2015-04-08

Preservation and hold time of radionuclides must account for both nuclear half-lives and nonnuclear loss mechanisms, but variations in the latter are often neglected. Metals-based defaults are inappropriate for long-lived non-metals C-14 and I-129, which are vulnerable to chemical and biological volatilization. Non-acidification is already widely practiced for them. Recommended addition measures from radiological and chemical literature include glass containers where possible, water filtration where possible, headspace minimization, light shielding, cold (4°C) storage and unfiltered water hold time of 28 days. Soil hold time may need to be shortened when water-logged, excessively sandy, or still adjusting to significant new contamination.

Examination of swallowing maneuver training and transfer of practiced behaviors to laryngeal vestibule kinematics in functional swallowing of healthy adults

PubMed Central

Guedes, Renata; Azola, Alba; Macrae, Phoebe; Sunday, Kirstyn; Mejia, Veerley; Vose, Alicia; Humbert, Ianessa A.

2017-01-01

Swallowing maneuvers are routinely trained in dysphagia rehabilitation with the assumption that practiced behaviors transfer to functional swallowing, however transfer is rarely examined in the deglutition literature. The goal of this study was to train the volitional laryngeal vestibule closure (vLVC) maneuver, which is a swallowing maneuver that targets prolonged laryngeal vestibule closure (LVC). In two different training experiments, 69 healthy adults underwent Long-hold (hold vLVC as long as possible) or Short-hold vLVC training (hold vLVC for 2 seconds). Before and after vLVC training, natural swallows (swallowing without a therapeutic technique) were completed. The outcome variables included laryngeal vestibule closure reaction time and the duration of laryngeal vestibule closure. Results indicate that during both Long-hold and Short-hold vLVC trainings, vLVC swallows had faster laryngeal vestibule closure reaction times and longer durations of laryngeal vestibule closure than in pre-training 5ml liquid swallows. However, only faster laryngeal vestibule closure reaction times transferred to post-training 5ml liquid swallows (20–24% faster), but not prolonged durations of laryngeal vestibule closure. Our findings suggest that swallowing maneuver training has the potential to induce transfer of what was practiced to functional swallowing behavior, although not all practiced behaviors may generalize. These findings are significant for bolstering the effectiveness of dysphagia management medical settings and should be tested in individuals with dysphagia. PMID:28322908

Examination of swallowing maneuver training and transfer of practiced behaviors to laryngeal vestibule kinematics in functional swallowing of healthy adults.

PubMed

Guedes, Renata; Azola, Alba; Macrae, Phoebe; Sunday, Kirstyn; Mejia, Veerley; Vose, Alicia; Humbert, Ianessa A

2017-05-15

Swallowing maneuvers are routinely trained in dysphagia rehabilitation with the assumption that practiced behaviors transfer to functional swallowing, however transfer is rarely examined in the deglutition literature. The goal of this study was to train the volitional laryngeal vestibule closure (vLVC) maneuver, which is a swallowing maneuver that targets prolonged laryngeal vestibule closure (LVC). In two different training experiments, 69 healthy adults underwent Long-hold (hold vLVC as long as possible) or Short-hold vLVC training (hold vLVC for 2s). Before and after vLVC training, natural swallows (swallowing without a therapeutic technique) were completed. The outcome variables included laryngeal vestibule closure reaction time and the duration of laryngeal vestibule closure. Results indicate that during both Long-hold and Short-hold vLVC trainings, vLVC swallows had faster laryngeal vestibule closure reaction times and longer durations of laryngeal vestibule closure than in pre-training 5ml liquid swallows. However, only faster laryngeal vestibule closure reaction times transferred to post-training 5ml liquid swallows (20-24% faster), but not prolonged durations of laryngeal vestibule closure. Our findings suggest that swallowing maneuver training has the potential to induce transfer of what was practiced to functional swallowing behavior, although not all practiced behaviors may generalize. These findings are significant for bolstering the effectiveness of dysphagia management in medical settings and should be tested in individuals with dysphagia. Copyright © 2017 Elsevier Inc. All rights reserved.

Effects of vegetable juice powder concentration and storage time on some chemical and sensory quality attributes of uncured, emulsified cooked sausages.

PubMed

Sindelar, J J; Cordray, J C; Sebranek, J G; Love, J A; Ahn, D U

2007-06-01

Uncured, no-nitrate/nitrite-added meat products can be manufactured with vegetable juice powder (VJP) and a starter culture containing Staphylococcus carnosus, resulting in quality and sensory attributes similar to traditional cured products. The 1st objective of this study was to determine the effects of varying concentrations of VJP and incubation times (MIN-HOLD) on quality characteristics, including lipid oxidation, color, and cured meat pigment concentrations, of emulsified-frankfurter-style-cooked (EFSC) sausages over a 90-d storage period. The 2nd objective was to compare residual nitrate and nitrite content resulting from different processing treatments and the 3rd objective was to assess sensory properties of finished products. Four EFSC sausage treatments (TRT) (TRT 1: 0.20% VJP, 30 MIN-HOLD; TRT 2: 0.20% VJP, 120 MIN-HOLD; TRT 3: 0.40% VJP, 30 MIN-HOLD; TRT 4: 0.40% VJP, 120 MIN-HOLD) and a sodium nitrite-added control (C) were used for this study. No differences for lipid oxidation (TBARS) between any TRTs and C or over time were observed. No differences (P > 0.05) for CIE L* values were found between TRTs. CIE a* and reflectance ratio values revealed that TRTs 2, 4, and C were redder than TRTs 1 and 3 at day 0. Trained sensory intensity ratings for cured aroma, cured color, cured flavor, uniform color, and firmness determined that all but TRT 1 were similar to C. These results indicate a longer incubation time (120 compared with 30 min) was found more critical than VJP level (0.20% or 0.40%) to result in products comparable to a sodium nitrite-added control.

Rebreather Unit to Prolong Underwater Survival Time.

PubMed

House, Carol M; Shaw, Anneliese M; Roiz de Sa, Daniel G

2015-12-01

This study investigated whether the timing of activation affects the utility of an emergency underwater rebreather unit (RBU) when submerged in cold water. On two successive occasions, 16 male UK Royal Marines were submerged in stirred water at 12.2°C for up to 78 s. The subjects were lowered (taking 18 s) into the water in a seated position and were instructed to take a large breath in, activate the unit, breath-hold for as long as possible, exhale into the unit, and breathe normally to and from the unit for the remainder of submersion. On one occasion the subjects were instructed to activate the RBU when the water reached chest height (Condition-1) and, on the other, prior to the feet entering the water (Condition-2). Measurements were made of the duration of breath-hold, rebreathing and submersion, exhaled oxygen and carbon dioxide concentrations, skin temperature, and heart rate. In 16 of the 32 submersions, the breath-hold was released before the subject became fully submerged and in 8 submersions the subject requested early withdrawal from the water. Mean (SD) breath-hold duration was 14.0 (13.8) s and the duration of rebreathing was 45.9 (21.9) s. The duration of breath-hold once completely submerged was longer in Condition-1 (9.1 s) than Condition-2 (4.1 s). The study indicates the RBU should be activated just before the mouth becomes submerged rather than before entering the water, and that the RBU will prolong underwater stay time, thereby increasing survival prospects. House CM, Shaw AM, Roiz de Sa DG. Rebreather unit to prolong underwater stay time, thereby increasing survival prospects.

Conceptual design and programmatics studies of space station accommodations for Life Sciences Research Facilities (LSRF)

NASA Technical Reports Server (NTRS)

1985-01-01

Conceptual designs and programmatics of the space station accommodations for the Life Sciences Research Facilities (LSRF) are presented. The animal ECLSS system for the LSRF provides temperature-humidity control, air circulation, and life support functions for experimental subjects. Three ECLSS were studied. All configurations presented satisfy the science requirements for: animal holding facilities with bioisolation; facilities interchangeable to hold rodents, small primates, and plants; metabolic cages interchangeable with standard holding cages; holding facilities adaptable to restrained large primates and rodent breeding/nesting cages; volume for the specified instruments; enclosed ferm-free workbench for manipulation of animals and chemical procedures; freezers for specimen storage until return; and centrifuge to maintain animals and plants at fractional g to 1 g or more, with potential for accommodating humans for short time intervals.

An Energy Scaled and Expanded Vector-Based Forwarding Scheme for Industrial Underwater Acoustic Sensor Networks with Sink Mobility.

PubMed

Wadud, Zahid; Hussain, Sajjad; Javaid, Nadeem; Bouk, Safdar Hussain; Alrajeh, Nabil; Alabed, Mohamad Souheil; Guizani, Nadra

2017-09-30

Industrial Underwater Acoustic Sensor Networks (IUASNs) come with intrinsic challenges like long propagation delay, small bandwidth, large energy consumption, three-dimensional deployment, and high deployment and battery replacement cost. Any routing strategy proposed for IUASN must take into account these constraints. The vector based forwarding schemes in literature forward data packets to sink using holding time and location information of the sender, forwarder, and sink nodes. Holding time suppresses data broadcasts; however, it fails to keep energy and delay fairness in the network. To achieve this, we propose an Energy Scaled and Expanded Vector-Based Forwarding (ESEVBF) scheme. ESEVBF uses the residual energy of the node to scale and vector pipeline distance ratio to expand the holding time. Resulting scaled and expanded holding time of all forwarding nodes has a significant difference to avoid multiple forwarding, which reduces energy consumption and energy balancing in the network. If a node has a minimum holding time among its neighbors, it shrinks the holding time and quickly forwards the data packets upstream. The performance of ESEVBF is analyzed through in network scenario with and without node mobility to ensure its effectiveness. Simulation results show that ESEVBF has low energy consumption, reduces forwarded data copies, and less end-to-end delay.

Analysis of holding time variations to Ni and Fe content and morphology in nickel laterite limonitic reduction process by using coal-dolomite bed

NASA Astrophysics Data System (ADS)

Abdul, Fakhreza; Pintowantoro, Sungging; Yuwandono, Ridwan Bagus

2018-04-01

With the depletion of nickel sulfide ore resources, the nickel laterit processing become an attention to fulfill nickel world demans. Reducing laterite nickel by using a low cost carbonaceous reductan has proved produces high grade ferronickel alloy. In this research, reduction was carried out to low grade laterite nickel (limonite) with 1.25% nikel content by using CO gas reductant formed by reaction between coal and dolomite. Reduction process preceded by forming brickets mixture from limonit ore, coal, and Na2SO4, then the brickets placed inside crucible bed together with dolomit and reduced at temperature 1400 °C with holding time variations 4, 6, and 8 hours. EDX, XRD, and SEM test were carried out to find out the Ni and nickel grade after reduced, the phases that formed, and the morphology brickets after reduced. The reduction results shows that the highest increase on nickel grade was obtained by 8 hours holding time increasing 5.84 % from initial grade, and the highest recovery was obtained by 6 hours holding time with recovery 88.51 %. While the higest increase on Fe grade was obtained by 4 hours holding time, and the highest recovery Fe was obtained by 4 hours holding time with recovery 85.41%.

DETERMINATION OF THE CREEP–FATIGUE INTERACTION DIAGRAM FOR ALLOY 617

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wright, J. K.; Carroll, L. J.; Sham, T. -L.

Alloy 617 is the leading candidate material for an intermediate heat exchanger for the very high temperature reactor. To evaluate the behavior of this material in the expected service conditions, creep-fatigue testing was performed. Testing has been performed primarily on a single heat of material at 850 and 950°C for total strain ranges of 0.3 to 1% and tensile hold times as long as 240 minutes. At 850°C, increases in the tensile hold duration degraded the creep fatigue resistance, at least to the investigated strain-controlled hold time of up to 60 minutes at the 0.3% strain range and 240 minutesmore » at the 1.0% strain range. At 950°C, the creep-fatigue cycles to failure becomes constant with increasing hold times, indicating saturation occurs at relatively short hold times. The creep and fatigue damage fractions have been calculated and plotted on a creep-fatigue interaction D-diagram. Results from earlier creep-fatigue tests at 800 and 1000°C on an additional heat of Alloy 617 are also plotted on the D-diagram. The methodology for calculating the damage fractions will be presented, and the effects of strain rate, strain range, temperature, hold time, and strain profile (i.e. holds in tension, compression or both) on the creep-fatigue damage will be explored.« less

Handling Technique Development of Live Carp, Cyprinus carpio, In Cold Dry Styrofoam Box

NASA Astrophysics Data System (ADS)

Ketut Suwetja, I.; Salindeho, Netty; Gede Prabawa Suwetja, I.

2017-10-01

The study focused on several following aspects: temperature and time optimation for fainting, holding media optimation, temperature and time optimation for recovery, and their correlation with mortality rate of carp, Cyprinus carpio. Fainting occurred at the optimum time of 11 minutes and 03 seconds, temperature of 8°C, and holding time of 6 hours. Holding medium was rice husk. The fastest consciousness of the fish was found in 6 volt-aerated water medium. The fish consciousness after 6 hours of storing in the rice husk at the fainting temperature of 8°C was found faster (p < 0.05), 11 minutes and 15 seconds, than that added with 0.02% of clove oil, 25 minutes and 16 seconds. The fish mortality rate after 6 hours of storage in the rice husk at fainting temperature of 8°C was lower (p < 0.05), 46%, than that with addition of 0.02% of clove oil, 75%.

Effect of the holding time at 15 °C prior to cryopreservation, the thawing rate and the post-thaw incubation temperature on the boar sperm quality after cryopreservation.

PubMed

Tomás, Cristina; Gómez-Fernández, José; Gómez-Izquierdo, Emilio; de Mercado, Eduardo

2014-01-30

The aim of the present study was to evaluate the effect of the holding time at 15 °C prior to cryopreservation (2, 4 and 8h), thawing rate (37 °C for 20s or 70 °C for 8s) and post-thaw incubation temperature (15 °C or 37 °C) on the post-thaw boar sperm quality. These are important time periods in the freezing-thawing process which have been less studied. Sperm-rich ejaculate fractions from three healthy boars were collected once a week for five consecutive weeks and were cryopreserved with the lactose-egg yolk extender (LEY). Sperm quality was determined by assessing the motility, the acrosome status, and the sperm plasma membrane integrity at 30, 150 and 240 min of incubation. The results show that with the holding time at 15 °C prior to cryopreservation there was not a clear effect until at least 24h of holding time. The thawing rate and the post-thaw incubation temperature, however, had a marked effect on sperm quality. When the samples were thawed at 70 °C for 8s, the sperm viability, motility and some kinetic variables (VCL, VSL, VAP and ALH) were greater than with results observed when the samples were thawed at 37 °C for 20s. In addition after thawing the sperm samples incubated at 15 °C had a sustained sperm quality for longer, up to 4h post-thawing. Copyright © 2014 Elsevier B.V. All rights reserved.

Can we still beat "buy-and-hold" for individual stocks?

NASA Astrophysics Data System (ADS)

Hui, Eddie C. M.; Kevin Chan, Ka Kwan

2014-09-01

Many investors seek for a trading strategy to beat the "buy-and-hold" strategy. In light of this, Hui and Yam (2014) and Hui et al. (2014) derived a trading strategy from the Shiryaev-Zhou index, and found that the resulting strategy outperformed the "buy-and-hold" strategy for western and Asian securitized real estate indices respectively. However, whether the trading strategy works on individual stocks or not is still unknown. This is the first study to test whether the trading strategy can beat the "buy-and-hold" strategy on individual stocks. We construct two trading strategies and compare the resulting profits with the profits arising from the "buy-and-hold" strategy on Hang Seng Index (HSI), Hang Seng Property (HSP) Index and 12 constituent stocks of HSI during the period December 29, 1995-December 31, 2013. The second strategy (Strategy 2) is a new strategy which incorporates short-selling, and has the effect of multiplying the profit. The results show that our trading strategies are less effective on individual stocks than on stock indices, and are more effective on property stocks than on non-property stocks. Moreover, our strategies outperform "buy-and-hold" by a larger extent on stocks of which the Shiryaev-Zhou indices fluctuate less frequently. Furthermore, by tracking the resulting profits of the three strategies at different times along the whole period of observation, our strategies work better during "bad times" than during "good times". This reflects that our trading strategies are especially useful in protecting investors from substantial loss during market downturns.

Feasibility Study of Regenerative Burners in Aluminum Holding Furnaces

NASA Astrophysics Data System (ADS)

Hassan, Mohamed I.; Al Kindi, Rashid

2014-09-01

Gas-fired aluminum holding reverberatory furnaces are currently considered to be the lowest efficiency fossil fuel system. A considerable volume of gas is consumed to hold the molten metal at temperature that is much lower than the flame temperature. This will lead to more effort and energy consumption to capture the excessive production of the CO2. The concern of this study is to investigate the feasibility of the regenerative-burners' furnaces to increase the furnace efficiency to reduce gas consumption per production and hence result in less CO2 production. Energy assessments for metal holding furnaces are considered at different operation conditions. Onsite measurements, supervisory control and data acquisition data, and thermodynamics analysis are performed to provide feasible information about the gas consumption and CO2 production as well as area of improvements. In this study, onsite measurements are used with thermodynamics modeling to assess a 130 MT rectangular furnace with two regenerative burners and one cold-air holding burner. The assessment showed that the regenerative burner furnaces are not profitable in saving energy, in addition to the negative impact on the furnace life. However, reducing the holding and door opening time would significantly increase the operation efficiency and hence gain the benefit of the regenerative technology.

Effect of coating mild steel with CNTs on its mechanical properties and corrosion behaviour in acidic medium

NASA Astrophysics Data System (ADS)

Abdulmalik Abdulrahaman, Mahmud; Kamaldeeen Abubakre, Oladiran; Ambali Abdulkareem, Saka; Oladejo Tijani, Jimoh; Aliyu, Ahmed; Afolabi, Ayo Samuel

2017-03-01

The study investigated the mechanical properties and corrosion behaviour of mild steel coated with carbon nanotubes at different coating conditions. Multi-walled carbon nanotubes (MWCNTs) were synthesized via the conventional chemical vapour deposition reaction using bimetallic Fe-Ni catalyst supported on kaolin, with acetylene gas as a carbon source. The HRSEM/HRTEM analysis of the purified carbon materials revealed significant reduction in the diameters of the purified MWCNT bundles from 50 nm to 2 nm and was attributed to the ultrasonication assisted dispersion with surfactant (gum arabic) employed in purification process. The network of the dispersed MWCNTs was coated onto the surfaces of mild steel samples, and as the coating temperature and holding time increased, the coating thickness reduced. The mechanical properties (tensile strength, yield strength, hardness value) of the coated steel samples increased with increase in coating temperature and holding time. Comparing the different coating conditions, coated mild steels at the temperature of 950 °C for 90 min holding time exhibited high hardness, yield strength and tensile strength values compared to others. The corrosion current and corrosion rate of the coated mild steel samples decreased with increase in holding time and coating temperature. The lowest corrosion rate was observed on sample coated at 950 °C for 90 min.

[Cooling of boar spermatozoa prior to freezing and post thaw quality and evaluation of membrane state using chlortetracycline (CTC) staining].

PubMed

Kotzias-Bandeira, E; Waberski, D; Weitze, K F

1997-08-01

The influence of an extended holding time at room temperature (+18 degrees C) before freezing on boar sperm quality was investigated. 17 ejaculates were collected from 5 different boars by separation in sperm rich and sperm poor fraction. The ejaculate were split, diluted 1+1 with Merck I-Medium, and submitted to three different treatments before freezing: 1. Sperm rich fraction, cooling to +20 degrees C for 1.5 h and subsequent cooling to +15 degrees C for 2.5 h; 2. Sperm rich fraction, cooling to +18 degrees C for 4 h and subsequent holding time at +18 degrees C for 16 h; 3. Whole ejaculate (sperm rich fraction plus seminal plasma), cooling to +18 degrees C for 4 h and subsequent holding time at +18 degrees C for 16 h. Subjectively assessed post thaw motility (SMOT), computer-measured motility (CMOT), and acrosome integrity (NAR), assessed by phase contrast microscopy were significantly (p < 0.05) higher after extended holding time (procedure 2 and 3) compared to short holding time (procedure 1). The exposure to seminal plasma during holding had no significant effect. Chlortetracyclin (CTC) staining of sperm membranes gave no reliable information in the presence of an EDTA-containing preservation medium, used routinely in the preservation process.

B2 Grain Growth Behavior of a Ti-22Al-25Nb Alloy Fabricated by Hot Pressing Sintering

NASA Astrophysics Data System (ADS)

Jia, Jianbo; Liu, Wenchao; Xu, Yan; Chen, Chen; Yang, Yue; Luo, Junting; Zhang, Kaifeng

2018-05-01

Grain growth behavior of a powder metallurgy (P/M) Ti-22Al-25Nb alloy was investigated by applying a series of isothermal treatment tests over a wide range of temperatures and holding times. An isothermal treatment scheme was conducted in the B2 phase region (1070-1110 °C) and α 2 + B2 phase region (1010-1050 °C) at holding times of 10, 30 min, 1, 2, and 3 h, respectively. The effects of temperature and holding time on the microstructure evolution and microhardness of the P/M Ti-22Al-25Nb alloy at elevated temperatures were evaluated using optical microscope, scanning electron microscope, x-ray diffraction, and Vickers hardness test techniques. The results revealed that the alloy's treated microstructure was closely linked to temperature and holding time, respectively. The change law of B2 grain growth with holding time and temperature can be well interpreted by the Beck equation and Hillert equation, respectively. The B2 grain growth exponent n and activation energy Q were acquired based on experimental data in the α 2 + B2 and B2 phase regions. In addition, the grain growth contour map for the P/M Ti-22Al-25Nb alloy was constructed to depict variations in B2 grain size based on holding time and temperature.

Variable abattoir conditions affect Salmonella enterica prevalence and meat quality in swine and pork.

PubMed

Hurd, H S; Gailey, J K; McKean, J D; Griffith, R W

2005-01-01

Research suggests that abattoir holding pens pose significant Salmonella enterica risk to swine immediately preharvest. The goal of this study was to evaluate those factors related to holding that increased the prevalence of S. enterica in swine at slaughter. To accomplish this goal, we focused on holding time and flooring. Our objectives were to (1) compare Salmonella enterica prevalence among pigs held for short (15-45 min) versus long (up to 4 h) periods before slaughter; and (2) determine the impact of flooring (slatted vs. concrete) as it relates to the prevalence of S. enterica. The study consisted of seven repetitions at a large volume (11,000 head/day) Midwest abattoir. Each repetition consisted of one truck load of pigs (n = 170) sorted into one of three groups: (1) animals held for a short time (15-45 min) on solid floors (short-hold); (2) animals held for 4 +/- 0.5 h on slatted floors; and (3) animals held for 4 +/- 0.5 h on solid concrete floors. At slaughter, samples were collected from 30 pigs in each group. Cecal contents (20 mL), feces (20 g), and the ileocecal lymph node were cultured for S. enterica. Additionally, the effect of holding time on meat quality parameters (loin pH at 35 min and 6 h, color, drip loss) was evaluated for the first four replicates. The proportion of S. enterica-positive samples was highest (p < 0.05) in the cecum of pigs held on solid concrete floors (72.4%), and slightly less for pigs held on slatted floors (63.3%). Animals held for less than 45 min before slaughter demonstrated the lowest proportion of S. enterica-positive samples (52.9%). The pig prevalence, as measured by any one of the three samples being positive, was significantly different (p < 0.05) between animals held on solid floors (81%) and those animals held for 45 min or less before slaughter (69%). Meat quality, as measured by multiple parameters, was adversely affected by lack of a rest period. The mean 24-h pH was significantly lower for the short-hold group compared to the other two groups. The mean Minolta L and the drip loss were significantly higher in the short-hold group. From this and other studies, it appears that elimination of the holding process is not feasible S. enterica control option, given current U.S. harvesting systems.

26 CFR 53.4943-4 - Present holdings.

Code of Federal Regulations, 2011 CFR

2011-04-01

... for a certain period of time (the “first phase”). The effect of such treatment is to prevent a private... phase holding period and also to prevent the foundation from purchasing any additional business holdings... permitted holdings in such business enterprise will be immediately after the expiration of the first phase...

Infrared detector Dewars - Increased LN2 hold time and vacuum jacket life spans

NASA Technical Reports Server (NTRS)

Jennings, D. E.; Boyd, W. J.; Blass, W. E.

1976-01-01

IR detector Dewars commonly suffer from shorter than desired LN2 hold times and insulation jacket vacuum corruption over relatively short time periods. In an attempt to solve this problem for a 9144 detector Dewar, small 1 liter/s appendage ion pumps were selected for continuous pumping of the vacuum jackets. This procedure extended LN2 hold times from 20 to 60 h and virtually eliminated vacuum jacket corruption. Thus the detector systems are usable continuously over periods of 6 months or more.

Network analysis of pig movements: Loyalty patterns and contact chains of different holding types in Denmark

PubMed Central

Boklund, Anette; Halasa, Tariq H. B.; Toft, Nils; Lentz, Hartmut H. K.

2017-01-01

Understanding animal movements is an important factor for the development of meaningful surveillance and control programs, but also for the development of disease spread models. We analysed the Danish pig movement network using static and temporal network analysis tools to provide deeper insight in the connection between holdings dealing with pigs, such as breeding and multiplier herds, production herds, slaughterhouses or traders. Pig movements, which occurred between 1st January 2006 and 31st December 2015 in Denmark, were summarized to investigate temporal trends such as the number of active holdings, the number of registered movements and the number of pigs moved. To identify holdings and holding types with potentially higher risk for introduction or spread of diseases via pig movements, we determined loyalty patterns, annual network components and contact chains for the 24 registered holding types. The total number of active holdings as well as the number of pig movements decreased during the study period while the holding sizes increased. Around 60–90% of connections between two pig holdings were present in two consecutive years and around one third of the connections persisted within the considered time period. Weaner herds showed the highest level of in-loyalty, whereas we observed an intermediate level of in-loyalty for all breeding sites and for production herds. Boar stations, production herds and trade herds showed a high level of out-loyalty. Production herds constituted the highest proportion of holdings in the largest strongly connected component. All production sites showed low levels of in-going contact chains and we observed a high level of out-going contact chain for breeding and multiplier herds. Except for livestock auctions, all transit sites also showed low levels of out-going contact chains. Our results reflect the pyramidal structure of the underlying network. Based on the considered disease, the time frame for the calculation of network measurements needs to be adapted. Using these adapted values for loyalty and contact chains might help to identify holdings with high potential of spreading diseases and thus limit the outbreak size or support control or eradication of the considered pathogen. PMID:28662077

Network analysis of pig movements: Loyalty patterns and contact chains of different holding types in Denmark.

PubMed

Schulz, Jana; Boklund, Anette; Halasa, Tariq H B; Toft, Nils; Lentz, Hartmut H K

2017-01-01

Understanding animal movements is an important factor for the development of meaningful surveillance and control programs, but also for the development of disease spread models. We analysed the Danish pig movement network using static and temporal network analysis tools to provide deeper insight in the connection between holdings dealing with pigs, such as breeding and multiplier herds, production herds, slaughterhouses or traders. Pig movements, which occurred between 1st January 2006 and 31st December 2015 in Denmark, were summarized to investigate temporal trends such as the number of active holdings, the number of registered movements and the number of pigs moved. To identify holdings and holding types with potentially higher risk for introduction or spread of diseases via pig movements, we determined loyalty patterns, annual network components and contact chains for the 24 registered holding types. The total number of active holdings as well as the number of pig movements decreased during the study period while the holding sizes increased. Around 60-90% of connections between two pig holdings were present in two consecutive years and around one third of the connections persisted within the considered time period. Weaner herds showed the highest level of in-loyalty, whereas we observed an intermediate level of in-loyalty for all breeding sites and for production herds. Boar stations, production herds and trade herds showed a high level of out-loyalty. Production herds constituted the highest proportion of holdings in the largest strongly connected component. All production sites showed low levels of in-going contact chains and we observed a high level of out-going contact chain for breeding and multiplier herds. Except for livestock auctions, all transit sites also showed low levels of out-going contact chains. Our results reflect the pyramidal structure of the underlying network. Based on the considered disease, the time frame for the calculation of network measurements needs to be adapted. Using these adapted values for loyalty and contact chains might help to identify holdings with high potential of spreading diseases and thus limit the outbreak size or support control or eradication of the considered pathogen.

Effects of varying levels of vegetable juice powder and incubation time on color, residual nitrate and nitrite, pigment, pH, and trained sensory attributes of ready-to-eat uncured ham.

PubMed

Sindelar, J J; Cordray, J C; Sebranek, J G; Love, J A; Ahn, D U

2007-08-01

Vegetable juice powder (VJP) and a starter culture containing Staphylococcus carnosus have been identified as necessary ingredients for the manufacture of uncured, no-nitrate/nitrite-added meat products with quality and sensory attributes similar to traditional cured products. The objectives of this study were to determine the effects of varying concentrations of VJP and incubation time (MIN-HOLD) on quality characteristics, including lipid oxidation, color, and cured meat pigment concentrations, of ham over a 90-d storage period, compare residual nitrate and nitrite content, and determine if differences exist in sensory properties of finished products. Four ham treatments (TRT) (TRT 1: 0.20% VJP, 0 MIN-HOLD; TRT 2: 0.20% VJP, 120 MIN-HOLD; TRT 3: 0.35% VJP, 0 MIN-HOLD; TRT 4: 0.35% VJP, 120 MIN-HOLD) and a sodium nitrite-added control (C) were used for this study. No differences (P > 0.05) were observed between TRTs and C for CIE L*, a*, b*, and cured color measured by reflectance ratio. Lipid oxidation (TBARS) for combined TRTs and C revealed little change over time while the C had less (P < 0.05) lipid oxidation than TRTs 2 and 4 for combined days. No differences (P > 0.05) were reported for cured pigment concentration between TRTs and C. Trained sensory panel intensity ratings for ham and vegetable aroma, and flavor, color, and firmness showed that a high concentration (0.35%) of VJP resulted in the highest scores for undesirable vegetable aroma and flavor. Treatment combinations with a low concentration (0.20%) of VJP were comparable to the C for all sensory attributes.

12 CFR 1500.3 - What are the holding periods permitted for merchant banking investments?

Code of Federal Regulations, 2010 CFR

2010-01-01

... includes a depository institution controlled by the financial holding company and any subsidiary of such a depository institution. (4) Approval required to hold interests held in excess of time limit. A financial... financial holding company; (iii) Market conditions; (iv) The nature of the portfolio company's business; (v...

Optimization and Simulation of Plastic Injection Process using Genetic Algorithm and Moldflow

NASA Astrophysics Data System (ADS)

Martowibowo, Sigit Yoewono; Kaswadi, Agung

2017-03-01

The use of plastic-based products is continuously increasing. The increasing demands for thinner products, lower production costs, yet higher product quality has triggered an increase in the number of research projects on plastic molding processes. An important branch of such research is focused on mold cooling system. Conventional cooling systems are most widely used because they are easy to make by using conventional machining processes. However, the non-uniform cooling processes are considered as one of their weaknesses. Apart from the conventional systems, there are also conformal cooling systems that are designed for faster and more uniform plastic mold cooling. In this study, the conformal cooling system is applied for the production of bowl-shaped product made of PP AZ564. Optimization is conducted to initiate machine setup parameters, namely, the melting temperature, injection pressure, holding pressure and holding time. The genetic algorithm method and Moldflow were used to optimize the injection process parameters at a minimum cycle time. It is found that, an optimum injection molding processes could be obtained by setting the parameters to the following values: T M = 180 °C; P inj = 20 MPa; P hold = 16 MPa and t hold = 8 s, with a cycle time of 14.11 s. Experiments using the conformal cooling system yielded an average cycle time of 14.19 s. The studied conformal cooling system yielded a volumetric shrinkage of 5.61% and the wall shear stress was found at 0.17 MPa. The difference between the cycle time obtained through simulations and experiments using the conformal cooling system was insignificant (below 1%). Thus, combining process parameters optimization and simulations by using genetic algorithm method with Moldflow can be considered as valid.

Characterization of contact structures for the spread of infectious diseases in a pork supply chain in northern Germany by dynamic network analysis of yearly and monthly networks.

PubMed

Büttner, K; Krieter, J; Traulsen, I

2015-04-01

A major risk factor in the spread of diseases between holdings is the transport of live animals. This study analysed the animal movements of the pork supply chain of a producer group in Northern Germany. The parameters in-degree and out-degree, ingoing and outgoing infection chain, betweenness and ingoing and outgoing closeness were measured using dynamic network analysis to identify holdings with central positions in the network and to characterize the overall network topology. The potential maximum epidemic size was also estimated. All parameters were calculated for three time periods: the 3-yearly network, the yearly and the monthly networks. The yearly and the monthly networks were more fragmented than the 3-yearly network. On average, one-third of the holdings were isolated in the yearly networks and almost three quarters in the monthly networks. This represented an immense reduction in the number of holdings participating in the trade of the monthly networks. The overall network topology showed right-skewed distributions for all calculated centrality parameters indicating that network resilience was high concerning the random removal of holdings. However, for a targeted removal of holdings according to their centrality, a rapid fragmentation of the trade network could be expected. Furthermore, to capture the real importance of holdings for disease transmission, indirect trade contacts (infection chain) should be considered. In contrast to the parameters regarding direct trade contacts (degree), the infection chain parameter did not underestimate the potential risk of disease transmission. This became more obvious, the longer the observed time period was. For all three time periods, the results for the estimation of the potential maximum epidemic size illustrated that the outgoing infection chain should be chosen. It considers the chronological order and the directed nature of the contacts and has no restrictions such as the strongly connected components of a cyclic network. © 2013 Blackwell Verlag GmbH.

Modification of Sr on 4004 Aluminum Alloy

NASA Astrophysics Data System (ADS)

Guo, Erjun; Cao, Guojian; Feng, Yicheng; Wang, Liping; Wang, Guojun; Lv, Xinyu

2013-05-01

As a brazing foil, 4004 Al alloy has good welding performance. However, the high Si content decreases the plasticity of the alloy. To improve the plasticity of 4004 Al alloy and subsequently improve the productivity of 4004 Al foil or 434 composite foil, 4004 Al alloy was modified by Al-10%Sr master alloy. Modification effects of an additional amount of Sr, modification temperature, and holding time on 4004 aluminum alloy were studied by orthogonal design. The results showed that the greatest impact parameter of 4004 aluminum alloy modification was the additional amount of Sr, followed by holding time and modification temperature. The optimum modification parameters obtained by orthogonal design were as follows: Sr addition of 0.04%, holding time of 60 min, and modification temperature of 760°C. The effect of Sr addition on modification was analyzed in detail based on orthogonal results. With increasing of Sr addition, elongation of 4004 alloy increased at first, and decreased after reaching the maximum value.

Irradiation creep-fatigue interaction of type 316L stainless steel

NASA Astrophysics Data System (ADS)

Scholz, R.; Mueller, R.

1996-10-01

Type 316L stainless steel samples in both, 20% cold-worked (cw) and recrystallised (rc) conditions were exposed to strain controlled fatigue cycling in torsion at 400°C during an irradiation with 19 MeV deuterons. The effect of irradiation creep induced stress relaxation on the fatigue life was studied by imposing a hold time at the minimum strain value in the loading cycle. For the cw material at strain ranges of 1.13% and 1.3%, the absolute stress values, τ H, maintained during the hold time decreased with the number of cycles due to the irradiation creep induced stress relaxation. A mean stress was built up. The number of cycles to failure was considerably reduced in comparison to continuous cycling tests under thermal conditions. For the rc material at strain ranges of 1.03% and 1.4%, the values of τ H increased with the number of cycles, despite the hold time imposed, due to irradiation and/or cyclic hardening.

Interfacial and Mechanical Behavior of AA5456 Filling Friction-Stir-Welded Lap Joints Using Similar and Dissimilar Pins

NASA Astrophysics Data System (ADS)

Behmand, Saleh Alaei; Mirsalehi, Seyyed Ehsan; Omidvar, Hamid; Safarkhanian, Mohammad Ali

2016-10-01

In this article, filling friction stir welding (FFSW) of the remaining exit holes of AA5456 alloy friction-stir-welded lap joints was studied. For this purpose, the influences of different rotating speeds, holding times, and pin materials, AA5456 and AA2024, on the metallurgical structure and joint strength were investigated. The observations showed that defect-free lap joints are successfully obtainable by this method using similar and dissimilar consumable pins. The results indicated that the higher rotating speed and holding time adversely affect the weld performance. The best result was achieved for 30 seconds holding time, 500 rpm rotating speed, and AA2024 consumable pin. In this condition, a lap shear strength of 10 pct higher than that of the nonfilled joint, equivalent to about 94 pct of the original defect-free FSW joint, was obtained, whereas the GTAW filled joint showed only approximately 87 pct of the continuous FSW joint strength.

Active quench and reset integrated circuit with novel hold-off time control logic for Geiger-mode avalanche photodiodes.

PubMed

Deng, Shijie; Morrison, Alan P

2012-09-15

This Letter presents an active quench-and-reset circuit for Geiger-mode avalanche photodiodes (GM-APDs). The integrated circuit was fabricated using a conventional 0.35 μm complementary metal oxide semiconductor process. Experimental results show that the circuit is capable of linearly setting the hold-off time from several nanoseconds to microseconds with a resolution of 6.5 ns. This allows the selection of the optimal afterpulse-free hold-off time for the GM-APD via external digital inputs or additional signal processing circuitry. Moreover, this circuit resets the APD automatically following the end of the hold-off period, thus simplifying the control for the end user. Results also show that a minimum dead time of 28.4 ns is achieved, demonstrating a saturated photon-counting rate of 35.2 Mcounts/s.

Automatic control of a helicopter with a hanging load. [development and evaluation of automatic pilot for use with S-61 helicopter

NASA Technical Reports Server (NTRS)

Gupta, N. K.; Bryson, A. E., Jr.

1973-01-01

An autopilot logic is designed here for controlling a helicopter with a hanging load. A 16th order model for the system is decoupled into four subsystems: (1) a second order system for yawing motion, (2) a second order system for vertical motion, (3) a sixth order system for longitudinal motion, and (4) a sixth order system for lateral motion. A measuring scheme, which could be used in remote areas, is developed and filters are designed to estimate the state variables from these measurements. The autopilot can be used to move the load over short distances without retracting the cables. This is done by automatically shifting the autopilot modes from position-hold (hover) to acceleration-hold to velocity-hold (cruise) to deceleration-hold to velocity-hold (near hover) to position-hold (hover). Use of such an autopilot might save considerable turnaround time. The Sikorsky S-61 helicopter is chosen as an example vehicle. The performance of the controlled system is studied in the presence of longitudinal and lateral winds.

Improvement of bio-oil yield and quality in co-pyrolysis of corncobs and high density polyethylene in a fixed bed reactor at low heating rate

NASA Astrophysics Data System (ADS)

Supramono, D.; Lusiani, S.

2016-11-01

Over the past few decades, interest in developing biomass-derived fuel has been increasing rapidly due to the decrease in fossil fuel reserves. Bio-oil produced by biomass pyrolysis however contains high oxygen compounds resulting in low calorific-value fuel and therefore requiring upgrading. In co-pyrolysis of the feed blend of plastics of High Density Polyethylene (HDPE) and biomass of com cob particles, at some compositions free radicals from plastic decomposition containing more hydrogen radicals are able to bond oxygen radicals originating from biomass to reduce oxygenate compounds in the bio-oil thus increasing bio-oil quality. This phenomenon is usually called synergetic effect. In addition to that, the pattern of heating of the feed blend in the pyrolysis reactor is predicted to affect biooil quality and yield. In a batch reactor, co-pyrolysis of corncobs and HDPE requires low heating rate to reach a peak temperature at temperature rise period followed by heating for some time at peak temperature called holding time at constant temperature period. No research has been carried out to investigate how long holding time is set in co-pyrolysis of plastic and biomass to obtain high yield of bio-oil. Holding time may affect either crosslinking of free radicals in gas phase, which increases char product, or secondary pyrolysis in the gas phase, which increases non-condensable gas in the gas phase of pyrolysis reactor, both of which reduce bio-oil yield. Therefore, holding time of co-pyrolysis affects the mass rate of bio-oil formation as the pyrolysis proceeds and quality of the bio-oil. In the present work, effects of holding time on the yield and quality of bio-oil have been investigated using horizontal fixed bed of the feed blends at heating rate of 5°C, peak temperature of 500°C and N2 flow rate of 700 ml/minute. Holding time was varied from 0 to 70 minutes with 10 minutes interval. To investigate the effects of holding time, the composition of HDPE in the feed blend was varied 0, 50 and 100%, while the synergetic effect was investigated by varying the composition of HDPE in the feed blend 0, 25, 50, 75, and 100%. The results show that synergetic effect for non-oxygenate compound production started to work at 63% HDPE in the feed blend and beyond. It was observed that extension of holding time exceeding 0 minutes allowed increase ofbio-oil production rate followed reduction of the rate. Pyrolysis ofboth the corncob feed and the feed blend containing 50% HDPE equally reached maximum bio-oil production rate at holding time of 50 minutes, while that of HDPE feed at 30 minutes. The result pertaining to holding time indicates that biomass in the feed blend governs crosslinking - secondary pyrolysis in the co-pyrolysis.

An economic order quantity model with nonlinear holding cost, partial backlogging and ramp-type demand

NASA Astrophysics Data System (ADS)

San-José, Luis A.; Sicilia, Joaquín; González-de-la-Rosa, Manuel; Febles-Acosta, Jaime

2018-07-01

In this article, a deterministic inventory model with a ramp-type demand depending on price and time is developed. The cumulative holding cost is assumed to be a nonlinear function of time. Shortages are allowed and are partially backlogged. Thus, the fraction of backlogged demand depends on the waiting time and on the stock-out period. The aim is to maximize the total profit per unit time. To do this, a procedure that determines the economic lot size, the optimal inventory cycle and the maximum profit is presented. The inventory system studied here extends diverse inventory models proposed in the literature. Finally, some numerical examples are provided to illustrate the theoretical results previously propounded.

Two-Phase Slug Flow Heat Exchanger for Microbial Thermal Inactivation Research

PubMed Central

Stroup, W. H.; Dickerson, R. W.; Read, R. B.

1969-01-01

A continuous two-phase (air-liquid), slug flow, tubular heat exchanger was developed for microbial thermal inactivation research to give exposure times and temperatures in the range of high-temperature, short-time milk pasteurization as well as heat-treated sample volumes of at least 2 ml. The use of air to compartmentalize the liquid in the capillary tubing prevented the development of laminar flow, which enabled precise identification of the residence time of the fastest flowing particles in the heating, holding, and cooling sections of the instrument. Residence time distributions were quantitated by measuring the degree of spreading of radioactive tracers for water, whole milk, chocolate milk, cream, and ice-cream mix with holding temperatures from 50 to 72 C, holding times from 2 to 60 sec, and heating and cooling times of 1.7 sec each. For a holding time of 60 sec and a fastest particle velocity of 10.2 cm/sec, the velocity ratios of the fastest moving particle to the median particle were 1.05, 1.05, 1.10, and 1.13 for whole milk, chocolate milk, cream, and ice-cream mix, respectively. With shorter holding times, these velocity ratios were even closer to unity. These velocity ratios indicated that the instrument would be an effective tool for thermal inactivation research on microorganisms suspended in homogeneous fluids with a viscosity of 15 centipoises or less at the exposure temperature. PMID:5395711

Through-vial impedance spectroscopy of the mechanisms of annealing in the freeze-drying of maltodextrin: the impact of annealing hold time and temperature on the primary drying rate.

PubMed

Smith, Geoff; Arshad, Muhammad Sohail; Polygalov, Eugene; Ermolina, Irina

2014-06-01

The study aims to investigate the impact of annealing hold time and temperature on the primary drying rate/duration of a 10% (w/v) solution of maltodextrin with an emphasis on how the mechanisms of annealing might be understood from the in-vial measurements of the ice crystal growth and the glass transition. The electrical impedance of the solution within a modified glass vial was recorded between 10 and 10(6) Hz during freeze-drying cycles with varying annealing hold times (1-5 h) and temperatures. Primary drying times decreased by 7%, 27% and 34% (1.1, 4.3 and 5.5 h) with the inclusion of an annealing step at temperatures of -15°C, -10°C and -5°C, respectively. The glass transition was recorded at approximately -16°C during the re-heating and re-cooling steps, which is close to the glass transition (Tg ') reported for 10% (w/v) maltodextrin and therefore indicates that a maximum freeze concentration (∼86%, w/w, from the Gordon-Taylor equation) was achieved during first freezing, with no further ice being formed on annealing. This observation, coupled to the decrease in electrical resistance that was observed during the annealing hold time, suggests that the reduction in the drying time was because of improved connectivity of ice crystals because of Ostwald ripening rather than devitrification. © 2014 Wiley Periodicals, Inc. and the American Pharmacists Association.

Effects of shear load on frictional healing

NASA Astrophysics Data System (ADS)

Ryan, K. L.; Marone, C.

2014-12-01

During the seismic cycle of repeated earthquake failure, faults regain strength in a process known as frictional healing. Laboratory studies have played a central role in illuminating the processes of frictional healing and fault re-strengthening. These studies have also provided the foundation for laboratory-derived friction constitutive laws, which have been used extensively to model earthquake dynamics. We conducted laboratory experiments to assess the affect of shear load on frictional healing. Frictional healing is quantified during slide-hold-slide (SHS) tests, which serve as a simple laboratory analog for the seismic cycle in which earthquakes (slide) are followed by interseismic quiescence (hold). We studied bare surfaces of Westerly granite and layers of Westerly granite gouge (thickness of 3 mm) at normal stresses from 4-25 MPa, relative humidity of 40-60%, and loading and unloading velocities of 10-300 μm/s. During the hold period of SHS tests, shear stress on the sample was partially removed to investigate the effects of shear load on frictional healing and to isolate time- and slip-dependent effects on fault healing. Preliminary results are consistent with existing works and indicate that frictional healing increases with the logarithm of hold time and decreases with normalized shear stress τ/τf during the hold. During SHS tests with hold periods of 100 seconds, healing values ranged from (0.013-0.014) for τ/τf = 1 to (0.059-0.063) for τ/τf = 0, where τ is the shear stress during the hold period and τf is the shear stress during steady frictional sliding. Experiments on bare rock surfaces and with natural and synthetic fault gouge materials are in progress. Conventional SHS tests (i.e. τ/τf = 1) are adequately described by the rate and state friction laws. However, previous experiments in granular quartz suggest that zero-stress SHS tests are not well characterized by either the Dieterich or Ruina state evolution laws. We are investigating the processes that produce shear stress dependent frictional healing, alternate forms of the state evolution law, and comparing results for friction of bare rock surfaces and granular fault gouge.

Assessment of the Effects of Holding Time and Temperature on Escherichia coli Densities in Surface Water Samples

PubMed Central

Pope, Misty L.; Bussen, Michelle; Feige, Mary Ann; Shadix, Lois; Gonder, Sharon; Rodgers, Crystal; Chambers, Yildiz; Pulz, Jessica; Miller, Ken; Connell, Kevin; Standridge, Jon

2003-01-01

Escherichia coli is a routinely used microbiological indicator of water quality. To determine whether holding time and storage conditions had an effect on E. coli densities in surface water, studies were conducted in three phases, encompassing 24 sites across the United States and four commonly used monitoring methods. During all three phases of the study, E. coli samples were analyzed at time 0 and at 8, 24, 30, and 48 h after sample collection. During phase 1, when 4°C samples were evaluated by Colilert or by placing a membrane onto mFC medium followed by transfer to nutrient agar containing 4-methylumbelliferyl-β-d-glucuronide (mFC/NA-MUG), three of four sites showed no significant differences throughout the 48-h study. During phase 2, five of seven sites showed no significant difference between time 0 and 24 h by membrane filtration (mFC/NA-MUG). When evaluated by the Colilert method, five of seven sites showed no significant difference in E. coli density between time 0 and 48 h. During phase 3, 8 of 13 sites showed no significant differences in E. coli densities between time 0 and the 48-h holding time, regardless of method. Based on the results of these studies, it appears that if samples are held below 10°C and are not allowed to freeze, most surface water E. coli samples analyzed by commonly used methods beyond 8 h after sample collection can generate E. coli data comparable to those generated within 8 h of sample collection. Notwithstanding this conclusion, E. coli samples collected from surface waters should always be analyzed as soon as possible. PMID:14532081

The effect of microstructure, temperature, and hold-time on low-cycle fatigue of As HIP P/M Rene 95

NASA Technical Reports Server (NTRS)

Bashir, S.; Antolovich, S. D.

1984-01-01

The effects of microstructure, temperature, plastic strain range, and hold time on the low-cycle fatigue (LCF) life were studied for Rene 95, an important Ni base superalloy used in jet engine disks. It was shown that the life could be varied by approximately an order of magnitude at elevated temperatures by simple heat treatments. The life was largest for the microstructure that promoted the most homogeneous deformation mode. The results are explained using the concept of a synergistic interaction between the deformation mode and boundary oxidation.

Optimizing mini-ridge filter thickness to reduce proton treatment times in a spot-scanning synchrotron system.

PubMed

Courneyea, Lorraine; Beltran, Chris; Tseung, Hok Seum Wan Chan; Yu, Juan; Herman, Michael G

2014-06-01

Study the contributors to treatment time as a function of Mini-Ridge Filter (MRF) thickness to determine the optimal choice for breath-hold treatment of lung tumors in a synchrotron-based spot-scanning proton machine. Five different spot-scanning nozzles were simulated in TOPAS: four with MRFs of varying maximal thicknesses (6.15-24.6 mm) and one with no MRF. The MRFs were designed with ridges aligned along orthogonal directions transverse to the beam, with the number of ridges (4-16) increasing with MRF thickness. The material thickness given by these ridges approximately followed a Gaussian distribution. Using these simulations, Monte Carlo data were generated for treatment planning commissioning. For each nozzle, standard and stereotactic (SR) lung phantom treatment plans were created and assessed for delivery time and plan quality. Use of a MRF resulted in a reduction of the number of energy layers needed in treatment plans, decreasing the number of synchrotron spills needed and hence the treatment time. For standard plans, the treatment time per field without a MRF was 67.0 ± 0.1 s, whereas three of the four MRF plans had treatment times of less than 20 s per field; considered sufficiently low for a single breath-hold. For SR plans, the shortest treatment time achieved was 57.7 ± 1.9 s per field, compared to 95.5 ± 0.5 s without a MRF. There were diminishing gains in time reduction as the MRF thickness increased. Dose uniformity of the PTV was comparable across all plans; however, when the plans were normalized to have the same coverage, dose conformality decreased with MRF thickness, as measured by the lung V20%. Single breath-hold treatment times for plans with standard fractionation can be achieved through the use of a MRF, making this a viable option for motion mitigation in lung tumors. For stereotactic plans, while a MRF can reduce treatment times, multiple breath-holds would still be necessary due to the limit imposed by the proton extraction time. To balance treatment time and normal tissue dose, the ideal MRF choice was shown to be the thinnest option that is able to achieve the desired breath-hold timing.

Energy Savings Through Thermally Efficient Crucible Technology: Fundamentals, Process Modeling, and Applications

NASA Astrophysics Data System (ADS)

Shi, Wenwu; Pinto, Brian

2017-12-01

Melting and holding molten metals within crucibles accounts for a large portion of total energy demand in the resource-intensive nonferrous foundry industry. Multivariate mathematical modeling aided by detailed material characterization and advancements in crucible technologies can make a significant impact in the areas of cost-efficiency and carbon footprint reduction. Key thermal properties such as conductivity and specific heat capacity were studied to understand their influence on crucible furnace energy consumption during melting and holding processes. The effects of conductivity on thermal stresses and longevity of crucibles were also evaluated. With this information, accurate theoretical models using finite element analysis were developed to study total energy consumption and melting time. By applying these findings to recent crucible developments, considerable improvements in field performance were reported and documented as case studies in applications such as aluminum melting and holding.

The Load and Time Dependence of Chemical Bonding-Induced Frictional Ageing of Silica at the Nanoscale

NASA Astrophysics Data System (ADS)

Tian, K.; Gosvami, N. N.; Goldsby, D. L.; Carpick, R. W.

2015-12-01

Rate and state friction (RSF) laws are empirical relationships that describe the frictional behavior of rocks and other materials in experiments, and reproduce a variety of observed natural behavior when employed in earthquake models. A pervasive observation from rock friction experiments is the linear increase of static friction with the log of contact time, or 'ageing'. Ageing is usually attributed to an increase in real area of contact associated with asperity creep. However, recent atomic force microscopy (AFM) experiments demonstrate that ageing of nanoscale silica-silica contacts is due to progressive formation of interfacial chemical bonds in the absence of plastic deformation, in a manner consistent with the multi-contact ageing behavior of rocks [Li et al., 2011]. To further investigate chemical bonding-induced ageing, we explored the influence of normal load (and thus contact normal stress) and contact time on ageing. Experiments that mimic slide-hold-slide rock friction experiments were conducted in the AFM for contact loads and hold times ranging from 23 to 393 nN and 0.1 to 100 s, respectively, all in humid air (~50% RH) at room temperature. Experiments were conducted by sequentially sliding the AFM tip on the sample at a velocity V of 0.5 μm/s, setting V to zero and holding the tip stationary for a given time, and finally resuming sliding at 0.5 μm/s to yield a peak value of friction followed by a drop to the sliding friction value. Chemical bonding-induced ageing, as measured by the peak friction minus the sliding friction, increases approximately linearly with the product of normal load and the log of the hold time. Theoretical studies of the roles of reaction energy barriers in nanoscale ageing indicate that frictional ageing depends on the total number of reaction sites and the hold time [Liu & Szlufarska, 2012]. We combine chemical kinetics analyses with contact mechanics models to explain our results, and develop a new approach for curve fitting ageing vs. load data which shows that the friction drop data points all fall on a master curve. The analysis yields physically reasonable values for the activation energy and activation volume of the chemical bonding process. Our study provides a basis to hypothesize that the kinetic processes in chemical bonding-induced ageing do not depend strongly on normal load.

A gated deep inspiration breath‐hold radiation therapy technique using a linear position transducer

PubMed Central

Denissova, Svetlana I.; Yewondwossen, Mammo H.; Andrew, John W.; Hale, Michael E.; Murphy, Carl H.; Purcell, Scott R.

2005-01-01

For patients with thoracic and abdominal lesions, respiration‐induced internal organ motion and deformations during radiation therapy are limiting factors for the administration of high radiation dose. To increase the dose to the tumor and to reduce margins, tumor movement during treatment must be minimized. Currently, several types of breath‐synchronized systems are in use. These systems include respiratory gating, deep inspiration breath‐hold, active breathing control, and voluntary breath‐hold. We used a linear position transducer (LPT) to monitor changes in a patient's abdominal cross‐sectional area. The LPT tracks changes in body circumference during the respiratory cycle using a strap connected to the LPT and wrapped around the patient's torso. The LPT signal is monitored by a computer that provides a real‐time plot of the patient's breathing pattern. In our technique, we use a CT study with multiple gated acquisitions. The Philips Medical Systems Q series CT imaging system is capable of operating in conjunction with a contrast injector. This allows a patient performing the deep inspiration breath‐hold maneuver to send a signal to trigger the CT scanner acquisitions. The LPT system, when interfaced to a LINAC, allows treatment to be delivered only during deep inspiration breath‐hold periods. Treatment stops automatically if the lung volume drops from a preset value. The whole treatment can be accomplished with 1 to 3 breath‐holds. This technique has been used successfully to combine automatically gated radiation delivery with the deep inspiration breath‐hold technique. This improves the accuracy of treatment for moving tumors, providing better target coverage, sparing more healthy tissue, and saving machine time. PACS numbers: 87.53.2j, 87.57.‐s PMID:15770197

High temperature low cycle fatigue mechanisms for nickel base and a copper base alloy. M.S. Thesis Final Report

NASA Technical Reports Server (NTRS)

Shih, C. I.

1982-01-01

Damage mechanisms were studied in Rene' 95 and NARloy Z, using optical, scanning and transmission in microscopy. In necklace Rene' 95, crack initiation was mainly associated with cracking of surface MC carbides, except for hold time tests at higher strain ranges where initiation was associated more with a grain boundary mechanism. A mixed mode of propagation with a faceted fracture morphology was typical for all cycle characters. The dependence of life on maximum tensile stress can be demonstrated by the data falling onto three lines corresponding to the three tensile hold times, in the life against maximum tensile stress plot. In NARloy Z, crack initiation was always at the grain boundaries. The mode of crack propagation depended on the cycle character. The life decreased with decreasing strain rate and with tensile holds. In terms of damage mode, different life prediction laws may be applicable to different cycle characters.

High-temperature tensile-hold crack-growth behavior of HASTELLOY® X alloy compared to HAYNES® 188 and HAYNES® 230® alloys

NASA Astrophysics Data System (ADS)

Lee, S. Y.; Lu, Y. L.; Liaw, P. K.; Choo, H.; Thompson, S. A.; Blust, J. W.; Browning, P. F.; Bhattacharya, A. K.; Aurrecoechea, J. M.; Klarstrom, D. L.

2008-03-01

The creep-fatigue crack-growth tests of HASTELLOY® X alloy were carried out at the temperatures of 649°C, 816°C, and 927°C in laboratory air. The experiments were conducted under a constant stress-intensity-factor-range (Δ K) control mode with a R-ratio of 0.05. In the constant Δ K tests, a Δ K of 27.5 MPa sqrt{m} and a triangular waveform with a frequency of 0.333 Hz were used. Various tensile hold times at the maximum load were imposed to study fatigue and creep-fatigue interactions. Crack lengths were measured by a direct current potential drop method. In this paper, effects of hold time and temperature on the crack-growth rates are discussed. Furthermore, the crack-growth rates of the HASTELLOY® X alloy are compared to those of the HAYNES® 188 and HAYNES® 230® superalloys.

The influence of hold time on the onset of plastic deformation in silicon

DOE PAGES

Wong, Sherman; Haberl, Bianca; Bradby, Jodie E.; ...

2015-12-24

Here, the formation of silicon (Si) in its -Sn form is known to be nucleation limited, with an undetermined period of time between when critical pressure for the trans- formation is reached and when the transformation actually occurs. In this letter, we use nanoindentation to apply critical pressure to diamond cubic Si and hold the sample under pressure to promote deformation via phase transformation and crystalline defects. We report that the number of indents in which phase transformation is observed increases with increasing hold time. Interestingly, the number of indents in which crystalline defects are observed also increase with increasingmore » hold time, suggesting crystalline defects are also nucleation limited. Raman spectroscopy and cross-sectional transmission electron microscopy is used to show that these two deformation mechanisms are mutually exclusive under the indentation conditions used within this letter.« less

Effects of capture and handling on survival of female northern pintails

USGS Publications Warehouse

Cox, R.R.; Afton, A.D.

1998-01-01

Identification of capture and handling procedures that influence survival of waterfowl has important research and management implications. We captured 347 female Northern Pintails (Anas acuta) using rocket nets, fitted them with harness (backpack-type) radio transmitters, and monitored their survival during the first 10 d following release. Females were 16 times more likely to die during the first 4 d of exposure than during days 5-10. Survival of females captured with small numbers of waterfowl (n < 172) was not related to holding time (time from capture until release), but survival of females captured with large numbers of waterfowl (n = 594) declined as holding time increased. Survival did not vary with age (immature or adult) or body condition (body mass adjusted for body size) of females. Survival was positively related to flight quality (scored as poor, moderate, or good) of females upon release; poor and moderate fliers were twice as likely to die as those scored in the next higher level of flight quality. Flight quality of females captured with small numbers of waterfowl was unrelated to holding time, but that of females captured with large numbers of waterfowl declined as holding time increased. In all cases where cause of mortalities could be determined (n = 12), we attributed proximate cause of death to predation. We recommend that holding time of ducks be minimized, particularly for those captured with large numbers of waterfowl in rocket nets.

A Holding Function for Conflict Probe Appiications

NASA Technical Reports Server (NTRS)

McNally, Dave; Walton, Joe

2004-01-01

Conflict Alerts for aircraft in holding patterns are often missed or in error due to fact that holding trajectories are not modeled in Conflict Alert or Conflict Probe logic. In addition, a controller in one sector may not know when aircraft are holding in a neighboring sector. These factors can lead to an increased potential for loss of separation while aircraft are flying in holding patterns. A holding function for conflict probe applications has been developed and tested with air traffic data from Fort Worth Center. The holding function automatically determines when an aircraft enters a holding pattern, builds a holding region around the pattern and then probes the region for conflict with other traffic. The operational concept of use assumes that air traffic controllers are very busy during periods when aircraft are in holding and therefore don't have time to manually enter information which defines a holding pattern and activates conflict probing. For this reason, it is important the holding function automatically detect aircraft in holding and compute a holding region for conflict analysis. The controller is then alerted if other aircraft are predicted to fly through the holding region at the holding altitude.

Reliable quantification of BOLD fMRI cerebrovascular reactivity despite poor breath-hold performance.

PubMed

Bright, Molly G; Murphy, Kevin

2013-12-01

Cerebrovascular reactivity (CVR) can be mapped using BOLD fMRI to provide a clinical insight into vascular health that can be used to diagnose cerebrovascular disease. Breath-holds are a readily accessible method for producing the required arterial CO2 increases but their implementation into clinical studies is limited by concerns that patients will demonstrate highly variable performance of breath-hold challenges. This study assesses the repeatability of CVR measurements despite poor task performance, to determine if and how robust results could be achieved with breath-holds in patients. Twelve healthy volunteers were scanned at 3 T. Six functional scans were acquired, each consisting of 6 breath-hold challenges (10, 15, or 20 s duration) interleaved with periods of paced breathing. These scans simulated the varying breath-hold consistency and ability levels that may occur in patient data. Uniform ramps, time-scaled ramps, and end-tidal CO2 data were used as regressors in a general linear model in order to measure CVR at the grey matter, regional, and voxelwise level. The intraclass correlation coefficient (ICC) quantified the repeatability of the CVR measurement for each breath-hold regressor type and scale of interest across the variable task performances. The ramp regressors did not fully account for variability in breath-hold performance and did not achieve acceptable repeatability (ICC<0.4) in several regions analysed. In contrast, the end-tidal CO2 regressors resulted in "excellent" repeatability (ICC=0.82) in the average grey matter data, and resulted in acceptable repeatability in all smaller regions tested (ICC>0.4). Further analysis of intra-subject CVR variability across the brain (ICCspatial and voxelwise correlation) supported the use of end-tidal CO2 data to extract robust whole-brain CVR maps, despite variability in breath-hold performance. We conclude that the incorporation of end-tidal CO2 monitoring into scanning enables robust, repeatable measurement of CVR that makes breath-hold challenges suitable for routine clinical practice. © 2013.

Horses Auto-Recruit Their Lungs by Inspiratory Breath Holding Following Recovery from General Anaesthesia

PubMed Central

Mosing, Martina; Waldmann, Andreas D.; MacFarlane, Paul; Iff, Samuel; Auer, Ulrike; Bohm, Stephan H.; Bettschart-Wolfensberger, Regula; Bardell, David

2016-01-01

This study evaluated the breathing pattern and distribution of ventilation in horses prior to and following recovery from general anaesthesia using electrical impedance tomography (EIT). Six horses were anaesthetised for 6 hours in dorsal recumbency. Arterial blood gas and EIT measurements were performed 24 hours before (baseline) and 1, 2, 3, 4, 5 and 6 hours after horses stood following anaesthesia. At each time point 4 representative spontaneous breaths were analysed. The percentage of the total breath length during which impedance remained greater than 50% of the maximum inspiratory impedance change (breath holding), the fraction of total tidal ventilation within each of four stacked regions of interest (ROI) (distribution of ventilation) and the filling time and inflation period of seven ROI evenly distributed over the dorso-ventral height of the lungs were calculated. Mixed effects multi-linear regression and linear regression were used and significance was set at p<0.05. All horses demonstrated inspiratory breath holding until 5 hours after standing. No change from baseline was seen for the distribution of ventilation during inspiration. Filling time and inflation period were more rapid and shorter in ventral and slower and longer in most dorsal ROI compared to baseline, respectively. In a mixed effects multi-linear regression, breath holding was significantly correlated with PaCO2 in both the univariate and multivariate regression. Following recovery from anaesthesia, horses showed inspiratory breath holding during which gas redistributed from ventral into dorsal regions of the lungs. This suggests auto-recruitment of lung tissue which would have been dependent and likely atelectic during anaesthesia. PMID:27331910

A case study of magnetic resonance imaging of cerebrovascular reactivity: a powerful imaging marker for mild traumatic brain injury.

PubMed

Chan, Suk-tak; Evans, Karleyton C; Rosen, Bruce R; Song, Tian-yue; Kwong, Kenneth K

2015-01-01

To use breath-hold functional magnetic resonance imaging (fMRI) to localize the brain regions with impaired cerebrovascular reactivity (CVR) in a female patient diagnosed with mild traumatic brain injury (mTBI). The extent of impaired CVR was evaluated 2 months after concussion. Follow-up scan was performed 1 year post-mTBI using the same breath-hold fMRI technique. Case report. fMRI blood oxygenation dependent level (BOLD) signals were measured under breath-hold challenge in a female mTBI patient 2 months after concussion followed by a second fMRI with breath-hold challenge 1 year later. CVR was expressed as the percentage change of BOLD signals per unit time of breath-hold. In comparison with CVR measurement of normal control subjects, statistical maps of CVR revealed substantial neurovascular deficits and hemispheric asymmetry within grey and white matter in the initial breath-hold fMRI scan. Follow-up breath-hold fMRI performed 1 year post-mTBI demonstrated normalization of CVR accompanied with symptomatic recovery. CVR may serve as an imaging biomarker to detect subtle deficits in both grey and white matter for individual diagnosis of mTBI. The findings encourage further investigation of hypercapnic fMRI as a diagnostic tool for mTBI.

Measuring vascular reactivity with breath-holds after stroke: a method to aid interpretation of group-level BOLD signal changes in longitudinal fMRI studies.

PubMed

Geranmayeh, Fatemeh; Wise, Richard J S; Leech, Robert; Murphy, Kevin

2015-05-01

Blood oxygenation level-dependent (BOLD) contrast functional magnetic resonance imaging (fMRI) is a widely used technique to map brain function, and to monitor its recovery after stroke. Since stroke has a vascular etiology, the neurovascular coupling between cerebral blood flow and neural activity may be altered, resulting in uncertainties when interpreting longitudinal BOLD signal changes. The purpose of this study was to demonstrate the feasibility of using a recently validated breath-hold task in patients with stroke, both to assess group level changes in cerebrovascular reactivity (CVR) and to determine if alterations in regional CVR over time will adversely affect interpretation of task-related BOLD signal changes. Three methods of analyzing the breath-hold data were evaluated. The CVR measures were compared over healthy tissue, infarcted tissue and the peri-infarct tissue, both sub-acutely (∼2 weeks) and chronically (∼4 months). In this cohort, a lack of CVR differences in healthy tissue between the patients and controls indicates that any group level BOLD signal change observed in these regions over time is unlikely to be related to vascular alterations. CVR was reduced in the peri-infarct tissue but remained unchanged over time. Therefore, although a lack of activation in this region compared with the controls may be confounded by a reduced CVR, longitudinal group-level BOLD changes may be more confidently attributed to neural activity changes in this cohort. By including this breath-hold-based CVR assessment protocol in future studies of stroke recovery, researchers can be more assured that longitudinal changes in BOLD signal reflect true alterations in neural activity. © 2015 The Authors Human Brain Mapping Published by Wiley Periodicals, Inc.

Effect of Time-of-Flight Information on PET/MR Reconstruction Artifacts: Comparison of Free-breathing versus Breath-hold MR-based Attenuation Correction.

PubMed

Delso, Gaspar; Khalighi, Mohammed; Ter Voert, Edwin; Barbosa, Felipe; Sekine, Tetsuro; Hüllner, Martin; Veit-Haibach, Patrick

2017-01-01

Purpose To evaluate the magnitude and anatomic extent of the artifacts introduced on positron emission tomographic (PET)/magnetic resonance (MR) images by respiratory state mismatch in the attenuation map. Materials and Methods The method was tested on 14 patients referred for an oncologic examination who underwent PET/MR imaging. The acquisition included standard PET and MR series for each patient, and an additional attenuation correction series was acquired by using breath hold. PET data were reconstructed with and without time-of-flight (TOF) information, first by using the standard free-breathing attenuation map and then again by using the additional breath-hold map. Two-tailed paired t testing and linear regression with 0 intercept was performed on TOF versus non-TOF and free-breathing versus breath-hold data for all detected lesions. Results Fluorodeoxyglucose-avid lesions were found in eight of the 14 patients included in the study. The uptake differences (maximum standardized uptake values) between PET reconstructions with free-breathing versus breath-hold attenuation ranged, for non-TOF reconstructions, from -18% to 26%. The corresponding TOF reconstructions yielded differences from -15% to 18%. Conclusion TOF information was shown to reduce the artifacts caused at PET/MR by respiratory mismatch between emission and attenuation data. © RSNA, 2016 Online supplemental material is available for this article.

12 CFR 225.138 - Statement of policy concerning divestitures by bank holding companies.

Code of Federal Regulations, 2012 CFR

2012-01-01

... concerning divestitures by bank holding companies. (a) From time to time the Board of Governors receives..., to extend time periods specified either by statute or by Board order for the divestiture of assets... ways. For example, divestiture may be ordered by the Board in connection with an acquisition found to...

12 CFR 225.138 - Statement of policy concerning divestitures by bank holding companies.

Code of Federal Regulations, 2011 CFR

2011-01-01

... concerning divestitures by bank holding companies. (a) From time to time the Board of Governors receives..., to extend time periods specified either by statute or by Board order for the divestiture of assets... ways. For example, divestiture may be ordered by the Board in connection with an acquisition found to...

12 CFR 225.138 - Statement of policy concerning divestitures by bank holding companies.

Code of Federal Regulations, 2013 CFR

2013-01-01

... policy concerning divestitures by bank holding companies. (a) From time to time the Board of Governors... Board, to extend time periods specified either by statute or by Board order for the divestiture of... number of ways. For example, divestiture may be ordered by the Board in connection with an acquisition...

12 CFR 225.138 - Statement of policy concerning divestitures by bank holding companies.

Code of Federal Regulations, 2014 CFR

2014-01-01

... policy concerning divestitures by bank holding companies. (a) From time to time the Board of Governors... Board, to extend time periods specified either by statute or by Board order for the divestiture of... number of ways. For example, divestiture may be ordered by the Board in connection with an acquisition...

Investigation of pouring temperature and holding time for semisolid metal feedstock production

NASA Astrophysics Data System (ADS)

Razak, N. A.; Ahmad, A. H.; Rashidi, M. M.

2017-10-01

Semisolid metal (SSM) processing, as a kind of new technology that exploits forming of alloys between solidus and liquidus temperatures, has attracted great attention from investigators for its thixotropic behaviour as well as having advantages in reducing porosity, macrosegregation, and forming forces during shaping process. Various techniques are employed to produce feedstock with fine globular microstructures, and direct thermal method is one of them. In this paper, the effect from different pouring temperatures and holding times using a direct thermal method on microstructure and hardness of aluminium alloy 6061 is presented. Molten aluminium alloy 6061 was poured into a cylindrical copper mould and cooled down to the semisolid temperature before being quenched in water at room temperature. The effect of different pouring temperatures of 660 °C, 680 °C, 700 °C, and holding time of 20 s, and 60 s on the microstructure of aluminium alloy 6061 were investigated. From the micrographs, it was found that the most globular structures were achieved at processing parameters of 660 °C pouring temperature and 60 s holding time. The highest density and hardness of the samples were found at the same processing parameters. It can be concluded that the most spheroidal microstructure, the highest density, and the hardness were recorded at lower pouring temperature and longer holding time.

Improved air trapping evaluation in chest computed tomography in children with cystic fibrosis using real-time spirometric monitoring and biofeedback.

PubMed

Kongstad, Thomas; Buchvald, Frederik F; Green, Kent; Lindblad, Anders; Robinson, Terry E; Nielsen, Kim G

2013-12-01

The quality of chest Computed Tomography (CT) images in children is dependent upon a sufficient breath hold during CT scanning. This study evaluates the influence of spirometric breath hold monitoring with biofeedback software on inspiratory and expiratory chest CT lung density measures, and on trapped air (TA) scoring in children with cystic fibrosis (CF). This is important because TA is an important component of early and progressive CF lung disease. A cross sectional comparison study was completed for chest CT imaging in two cohorts of CF children with comparable disease severity, using spirometric breath hold monitoring and biofeedback software (Copenhagen (COP)) or unmonitored breath hold manoeuvres (Gothenburg (GOT)). Inspiratory-expiratory lung density differences were calculated, and TA was scored to assess the difference between the two cohorts. Eighty-four chest CTs were evaluated. Mean (95%CI) change in inspiratory-expiratory lung density differences was 436 Hounsfield Units (HU) (408 to 464) in the COP cohort with spirometric breath hold monitoring versus 229 HU (188 to 269) in the GOT cohort with unmonitored breath hold manoeuvres (p<0.0001). The Mean TA (95%CI) score was 6.93 (6.05 to 7.82) in COP patients and 3.81 (2.89 to 4.73) in GOT (p<0.0001) patients. In children with comparable CF lung disease, spirometric breath hold monitoring during examination yielded a large difference in lung volume between inhalation and exhalation, and allowed for a significantly greater measured change in lung density and TA score, compared to unmonitored breath hold maneuvers. This has implications to the clinical use of chest CT, especially in children with early CF lung disease. Copyright © 2013 European Cystic Fibrosis Society. Published by Elsevier B.V. All rights reserved.

Draft ASME Boiler and Pressure Vessel Code Section III, Division 5, Section HB, Subsection B, Code Case for Alloy 617 and Background Documentation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wright, Julie Knibloe

2015-08-01

Alloy 617 is the leading candidate material for an intermediate heat exchanger for the very high temperature reactor. To evaluate the behavior of this material in the expected service conditions, strain controlled cyclic tests that include long hold times up to 240 minutes at maximum tensile strain were conducted at 850°C. In terms of the total number of cycles to failure, the fatigue resistance decreased when a hold time was added at peak tensile strain. Increases in the tensile hold duration degraded the creep fatigue resistance, at least to the investigated strain controlled hold time of up to 60 minutesmore » at the 0.3% strain range and 240 minutes at the 1.0% strain range. The creep fatigue deformation mode is considered relative to the lack of saturation, or continually decreasing number of cycles to failure with increasing hold times. Additionally, preliminary values from the 850°C creep fatigue data are calculated for the creep fatigue damage diagram and have higher values of creep damage than those from tests at 950°C.« less

The Role of Healthcare Professionals in Encouraging Parents to See and Hold Their Stillborn Baby: A Meta-Synthesis of Qualitative Studies

PubMed Central

Kingdon, Carol; O’Donnell, Emer; Givens, Jennifer; Turner, Mark

2015-01-01

Background Globally, during 2013 there were three million recorded stillbirths. Where clinical guidelines exist some recommend that professionals do not encourage parental contact. The guidance is based on quantitative evidence that seeing and holding the baby is not beneficial for everyone, but has been challenged by bereaved parents' organisations. We aim to inform future guideline development through a synthesis of qualitative studies reporting data relevant to the research question; how does the approach of healthcare professionals to seeing and holding the baby following stillbirth impact parents views and experiences? Methods/Findings Using a predetermined search strategy of PubMed and PsychINFO we identified robust qualitative studies reporting bereaved parental views and/or experiences relating to seeing and holding their stillborn baby (final search 24 February, 2014). Eligible studies were English language, reporting parental views, with gestational loss >20weeks. Quality was independently assessed by three authors using a validated tool. We used meta-ethnographic techniques to identify key themes and a line of argument synthesis. We included 12 papers, representing the views of 333 parents (156 mothers, 150 fathers, and 27 couples) from six countries. The final themes were: "[Still]birth: Nature of care is paramount", "Real babies: Perfect beauties, monsters and spectres", and "Opportunity of a lifetime lost." Our line-of-argument synthesis highlights the contrast between all parents need to know their baby, with the time around birth being the only time memories can be made, and the variable ability that parents have to articulate their preferences at that time. Thus, we hypothesised that how health professionals approach contact between parents and their stillborn baby demands a degree of active management. An important limitation of this paper is all included studies originated from high income, westernised countries raising questions about the findings transferability to other cultural contexts. We do not offer new evidence to answer the question "Should parents see and hold their stillborn baby?", instead our findings advance understanding of how professionals can support parents to make appropriate decisions in a novel, highly charged and dynamic situation. Conclusions Guidelines could be more specific in their recommendations regarding parental contact. The role of healthcare professionals in encouraging parents to see and hold their stillborn baby is paramount. Parental choice not to see their baby, apprehension, or uncertainty should be continuously revisited in the hours after birth as the opportunity for contact is fleeting and final. PMID:26154302

Do elite breath-hold divers suffer from mild short-term memory impairments?

PubMed

Billaut, François; Gueit, Patrice; Faure, Sylvane; Costalat, Guillaume; Lemaître, Frédéric

2018-03-01

Repeated apneas are associated with severe hypoxemia that may ultimately lead to loss of consciousness in some breath-hold divers. Despite increasing number of practitioners, the relationship between apnea-induced hypoxia and neurocognitive functions is still poorly understood in the sport of free diving. To shed light onto this phenomenon, we examined the impact of long-term breath-hold diving training on attentional processing, short-term memory, and long-term mnesic and executive functions. Thirty-six men matched for age, height, and weight were separated into the following 3 groups: (i) 12 elite breath-hold divers (EBHD), mean static apnea best time 371 s, 105 months mean apnea experience; (ii) 12 novice breath-hold divers, mean best time 243 s, 8.75 months mean apnea experience; and (iii) 12 physical education students with no breath-hold diving experience; all of these participants performed varied written and computerized neuropsychological tasks. Compared with the 2 other groups, the EBHD group was slower to complete the interference card during a Stroop test (F [1,33] = 4.70, p < 0.05), and presented more errors on the interference card (F [1,33] = 2.96, p < 0.05) and a lower total interference score (F [1,33] = 5.64, p < 0.05). The time to complete the interference card test was positively correlated with maximal static apnea duration (r = 0.73, p < 0.05) and the number of years of breath-hold diving training (r = 0.79, p < 0.001). These findings suggest that breath-hold diving training over several years may cause mild, but persistent, short-term memory impairments.

Microstructural evolution during reheating of A356 machining chips at semisolid state

NASA Astrophysics Data System (ADS)

Wang, Fang; Zhang, Wen-qiang; Xiao, Wen-long; Yamagata, Hiroshi; Ma, Chao-li

2017-08-01

The microstructural evolution of A356 machining chips in the semisolid state was studied at different temperatures and holding times. The results showed that the elongated α-Al grains first recrystallized in the semisolid state and then became globular with a high shape factor (SF). Both the temperature and the holding time clearly affected the grain size and SF. When the heating temperature or holding time was increased, the grain size and SF gradually increased and finally became stable. Moreover, the Vickers hardness of primary α-Al grains gradually decreased with increasing heating temperature. The optimal slurry for semisolid processing, with a good combination of grain size and SF, was obtained when the chips were held at 600°C for 15 min. The semisolid slurry of A356 chips exhibited a lower coarsening rate of α-Al grains than those produced by most of the conventional semisolid processes. The coarsening coefficient was determined to be 436 μm3·s-1 on the basis of the linear Lifshitz-Slyozov-Wagner (LSW) relationship.

The mechanisms of flame holding in the wake of a bluff body

NASA Technical Reports Server (NTRS)

Strehlow, R. A.; Malik, S.

1985-01-01

The flame holding mechanism for lean methane- and lean propane-air flames is examined under conditions where the recirculation zone is absent. The main objective of this work is to study the holding process in detail in an attempt to determine the mechanism of flame holding and also the conditions where this mechanism is viable and when it fails and blow-off occurs. Inverted flames held in the wake of a flat strip were studied. Experiments with different sizes of flame holders were performed. The velocity flow field was determined using a laser Doppler velocimetry technique. Equation of continuity was used to calculate the flame temperature from the change in area of flow streamlines before and after the flame. Observations of the inverted flame itself were obtained using schlieren and direct photography. Results show that there are different mechanisms operative at the time of blow-off for lean propane and methane flames. Blow-off or extinction occurs for lean propane-air flame in spite of the reaction going to completion and the disparity between the heat loss and the gain in mass diffusion in the reaction zone i.e., Le 1.0 causes the flame to blow-off. For methane-air flame the controlling factor or blow-off is incomplete reaction due to higher blowing rate leading to reduced residence time in the reaction zone.

Breath-hold duration in man and the diving response induced by face immersion.

PubMed

Sterba, J A; Lundgren, C E

1988-09-01

The objective of this study in 5 selected volunteer subjects was to see whether the circulatory diving response which is elicited by breath holding and by cold water on the face would affect the duration of maximal-effort breath holds. Compared to control measurements (breath holding during resting, breathing with 35 degrees C water on the face) breath holding with the face cooled by 20 degrees C water caused a 12% reduction of heart rate, 6% reduction of cardiac output, 33% reduction in [corrected] forearm blood flow, and 9% rise in mean arterial blood pressure, but there was no difference in breath-hold duration (control and experimental both 94 s). There were also no differences in time of appearance of the first involuntary respiratory efforts during breath holding, in alveolar gas exchange, or in breaking-point alveolar O2 and CO2 tensions. When the diving response was magnified by a brief bout of exercise so that there was a 19% [corrected] reduction in heart rate, 23% reduction in cardiac output, and 48% reduction in forearm blood flow, breath-hold duration was still unaffected by face cooling. Compared to intermittent immersions, continuous exposure of the face to cold water abolished the diving response, probably by a cold adaptation of facial thermal receptors. These results with cooling of the face only are consistent with our earlier finding that there was a negative correlation between the duration of a maximal-effort breath hold and the diving response during whole-body submersion in cold water.

High temperature, low-cycle fatigue of copper-base alloys in argon. Part 2: Zirconium-copper at 482, 538 and 593 C

NASA Technical Reports Server (NTRS)

Conway, J. B.; Stentz, R. H.; Berling, J. T.

1973-01-01

Zirconium-copper (1/2 hard) was tested in argon over the temperature range from 482 to 593 C in an evaluation of short-term tensile and low-cycle fatigue behavior. The effect of strain rate on the tensile properties was evaluated at 538 C and in general it was found that the yield and ultimate strengths increased as the strain rate was increased from 0.0004 to 0.01/sec. Ductility was essentially insensitive to strain rate in the case of the zirconium-copper alloy. Strain-rate and hold-time effects on the low cycle fatigue behavior of zirconium-copper were evaluated in argon at 538 C. These effects were as expected in that decreased fatigue life was noted as the strain rate decreased and when hold times were introduced into the tension portion of the strain-cycle. Hold times in compression were much less detrimental than hold times in tension.

Effects of temperature and holding time on bonding W and W-Cu composites with an amorphous W-Fe coated copper foil as the interlayer by hot-pressing

NASA Astrophysics Data System (ADS)

Zhao, Pei; Wang, Song; Guo, Shibin; Chen, Yixiang; Ling, Yunhan; Li, Jiangtao

2013-07-01

W and W-Cu composites were bonded with an amorphous W-Fe coated copper foil as the interlayer at different temperature and holding time by hot pressing method. Effects of the bonding temperature and holding time on the microstructure and thermal conductivity of the bonded specimens were investigated. The thermal conductivity of the bonded sample increased with the bonding temperature and reached the maximum at 1000 °C, but essentially unchanged with the holding time. Because at 1000 °C more W-Fe compounds would be formed at the interlayer, which were helpful for tight bonding of W and W-Cu composites, and the grain size was larger which could reduce thermal resistance. The W-Cu FGM bonded by this method showed good resistance to thermal load, and performed well when facing to short pulse plasma in experimental advanced superconducting tokamak (the first full superconductive fusion device in the world).

Effect of heating strategies on whey protein denaturation--Revisited by liquid chromatography quadrupole time-of-flight mass spectrometry.

PubMed

Akkerman, M; Rauh, V M; Christensen, M; Johansen, L B; Hammershøj, M; Larsen, L B

2016-01-01

Previous standards in the area of effect of heat treatment processes on milk protein denaturation were based primarily on laboratory-scale analysis and determination of denaturation degrees by, for example, electrophoresis. In this study, whey protein denaturation was revisited by pilot-scale heating strategies and liquid chromatography quadrupole time-of-flight mass spectrometer (LC/MC Q-TOF) analysis. Skim milk was heat treated by the use of 3 heating strategies, namely plate heat exchanger (PHE), tubular heat exchanger (THE), and direct steam injection (DSI), under various heating temperatures (T) and holding times. The effect of heating strategy on the degree of denaturation of β-lactoglobulin and α-lactalbumin was determined using LC/MC Q-TOF of pH 4.5-soluble whey proteins. Furthermore, effect of heating strategy on the rennet-induced coagulation properties was studied by oscillatory rheometry. In addition, rennet-induced coagulation of heat-treated micellar casein concentrate subjected to PHE was studied. For skim milk, the whey protein denaturation increased significantly as T and holding time increased, regardless of heating method. High denaturation degrees were obtained for T >100°C using PHE and THE, whereas DSI resulted in significantly lower denaturation degrees, compared with PHE and THE. Rennet coagulation properties were impaired by increased T and holding time regardless of heating method, although DSI resulted in less impairment compared with PHE and THE. No significant difference was found between THE and PHE for effect on rennet coagulation time, whereas the curd firming rate was significantly larger for THE compared with PHE. Micellar casein concentrate possessed improved rennet coagulation properties compared with skim milk receiving equal heat treatment. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Fatigue crack growth at elevated temperature 316 stainless steel and H-13 steel

NASA Technical Reports Server (NTRS)

Chen, W. C.; Liu, H. W.

1976-01-01

Crack growths were measured at elevated temperatures under four types of loading: pp, pc, cp, and cc. In H-13 steel, all these four types of loading gave nearly the same crack growth rates, and the length of hold time had negligible effects. In AISI 316 stainless steel, the hold time effects on crack growth rate were negligible if the loading was tension-tension type; however, these effects were significant in reversed bending load, and the crack growth rates under these four types of loading varied considerably. Both tensile and compressive hold times caused increased crack growth rate, but the compressive hold period was more deleterious than the tensile one. Metallographic examination showed that all the crack paths under different types of loading were largely transgranular for both CTS tension-tension specimens and SEN reversed cantilever bending specimens. In addition, an electric potential technique was used to monitor crack growth at elevated temperature.

Effect of pre- and post-marination aging on meat quality attributes of early deboned (2 h postmortem) broiler breast fillets.

PubMed

Kuttappan, V A; Gunsaulis, V B; Mauromoustakos, A; Meullenet, J F; Owens, C M

2016-11-01

Marination is an effective method that can be used to improve the tenderness of early deboned breast fillets. The present study was designed to evaluate the effect of pre- and post-marination aging of 2 h postmortem (PM) deboned chicken fillets to get optimum meat quality. In this study, a total of 300 broilers (43 to 46 d of age) were processed using an in-line system and deboned at 2 h PM. Fillets were marinated, at either 2.5, 4, 6, 8 or 24 h PM, using vacuum tumbling (20 min) with a 15% marinade (final concentration of 0.5% salt and 0.45% phosphate). A non-marinated control (CON) was included. The left (HOLD) fillets were aged (held at 4°C for 24 h) prior to freezing post-marination while the right (NO HOLD) fillets were frozen immediately after marination to simulate various commercial practices. Marination pickup (MPU), total marinade retained after thawing (TMR), total purge loss after thawing (TPL), cook loss (CL), and Meullenet-Owens Razor Shear energy (MORSE) values were measured. Both in HOLD and NO HOLD fillets, there was an increase (P < 0.05) in MPU and TMR as the time of marination increased from 2.5 to 24 h PM. Furthermore, the HOLD fillets had a higher (P < 0.05) TPL when compared to the NO HOLD group. There was a higher (P < 0.05) CL for the CON fillets when compared to all marinated fillets suggesting that marination resulted in better water holding capacity. However, both in HOLD and NO HOLD groups, the MORSE values for the marinated fillets decreased (P < 0.05) from 4 h PM onwards, with 8 and 24 h PM having lower (P < 0.05) values than all other treatments. The results of this study suggest that pre-marination aging (aging after deboning prior to marination) of early (2 h PM) deboned fillets to 8 h PM can provide better tumble marination pickup and retention as well as tenderness (or lower shear values). © 2016 Poultry Science Association Inc.

Asteroid Studies: A 35-Year Forecast

NASA Astrophysics Data System (ADS)

Rivkin, A. S.; Denevi, B. W.; Klima, R. L.; Ernst, C. M.; Chabot, N. L.; Barnouin, O. S.; Cohen, B. A.

2017-02-01

We are in an active time for asteroid studies, which fall at the intersection of science, planetary defense, human exploration, and in situ resource utilization. We look forward and extrapolate what the future may hold for asteroid science.

Creep-Fatigue Behavior of Alloy 617 at 850°C

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carroll, Laura

Creep-fatigue deformation is expected to be a significant contributor to the potential factors that limit the useful life of the Intermediate Heat Exchanger (IHX) in the Very High Temperature Reactor (VHTR) nuclear system.[1] The IHX of a high temperature gas reactor will be subjected to a limited number of transient cycles due to start-up and shut-down operations imparting high local stresses on the component. This cycling introduces a creep-fatigue type of interaction as dwell times occur intermittently. The leading candidate alloy for the IHX is a nickel-base solid solution strengthened alloy, Alloy 617, which must safely operate near the expectedmore » reactor outlet temperature of up to 950 °C.[1] This solid solution strengthened nickel-base alloy provides an interesting creep-fatigue deformation case study because it has characteristics of two different alloy systems for which the cyclic behavior has been extensively investigated. Compositionally, it resembles nickel-base superalloys, such as Waspalloy, IN100, and IN718, with the exception of its lower levels of Al. At temperatures above 800 °C, the microstructure of Alloy 617, however, does not contain the ordered ?’ or ?’’ phases. Thus microstructurally, it is more similar to an austenitic stainless steel, such as 316 or 304, or Alloy 800H comprised of a predominantly solid solution strengthened matrix phase with a dispersion of inter- and intragranular carbides. Previous studies of the creep-fatigue behavior of Alloy 617 at 950 °C indicate that the fatigue life is reduced when a constant strain dwell is added at peak tensile strain.[2-5] This results from the combination of faster crack initiation occurring at surface-connected grain boundaries due to oxidation from the air environment along with faster, and intergranular, crack propagation resulting from the linking of extensive interior grain boundary cracking.[3] Saturation, defined as the point at which further increases in the strain-controlled hold time duration no longer decreases the cycle life, has been observed for Alloy 617 at 950 °C at least to the investigated hold times[2,3], as illustrated through a plot of cycles to failure v. hold time in Figure 1. The 950 °C creep-fatigue data set generated by Totemeier and Tian[5] at the 0.3% and 1.0% strain range is consistent in magnitude in terms of the cycles to failure data of that of Carroll et al., however, 0.3% strain range data did not exhibit saturation at hold times of up to 10 min. At 1.0% total strain, saturation in the number of cycles to failure was observed within the investigated peak tensile hold times of up to 10 min[5]. The data of Carroll et al.[2,3] in Figure 1 and Totemeier and Tian[5] is also consistent in magnitude with the data of Rao and coworkers[4] investigated at the 0.6% strain range. It should be noted that saturation in the number of cycles to failure is not present in the data published by Rao and coworkers[4] for tensile hold times of up to 120 min. The latter testing was in a simulated primary-circuit helium gas as opposed to air and a single data point is reported for the longer hold time conditions.« less

Removal of Fluorides and Chlorides from Zinc Oxide Fumes by Microwave Sulfating Roasting

NASA Astrophysics Data System (ADS)

Li, Zhiqiang; Zhang, Libo; Chen, Guo; Peng, Jinhui; Zhou, Liexing; Yin, Shaohua; Liu, Chenhui

2015-10-01

Dechlorination and defluorination from zinc oxide dust by microwave sulfating roasting was investigated in this study. According to proposed reactions in the process, detailed experiments were systematically conducted to study the effect of roasting temperature, holding time, air and steam flow rates on the efficiency of the removal of F and Cl. The results show that 92.3% of F and 90.5% of Cl in the fume could be purified when the condition of the roasting temperature of 650 °C, holding time at 60 min, air flow of 300 L/h and steam flow of 8 ml/min was optimized. Our investigation indicates that microwave sulfating roasting could be a promising new way for the dechlorination and defluorination from zinc oxide dust.

A Model of Batch Scheduling for a Single Batch Processor with Additional Setups to Minimize Total Inventory Holding Cost of Parts of a Single Item Requested at Multi-due-date

NASA Astrophysics Data System (ADS)

Hakim Halim, Abdul; Ernawati; Hidayat, Nita P. A.

2018-03-01

This paper deals with a model of batch scheduling for a single batch processor on which a number of parts of a single items are to be processed. The process needs two kinds of setups, i. e., main setups required before processing any batches, and additional setups required repeatedly after the batch processor completes a certain number of batches. The parts to be processed arrive at the shop floor at the times coinciding with their respective starting times of processing, and the completed parts are to be delivered at multiple due dates. The objective adopted for the model is that of minimizing total inventory holding cost consisting of holding cost per unit time for a part in completed batches, and that in in-process batches. The formulation of total inventory holding cost is derived from the so-called actual flow time defined as the interval between arrival times of parts at the production line and delivery times of the completed parts. The actual flow time satisfies not only minimum inventory but also arrival and delivery just in times. An algorithm to solve the model is proposed and a numerical example is shown.

Computational fluid dynamics modeling of gas dispersion in multi impeller bioreactor.

PubMed

Ahmed, Syed Ubaid; Ranganathan, Panneerselvam; Pandey, Ashok; Sivaraman, Savithri

2010-06-01

In the present study, experiments have been carried out to identify various flow regimes in a dual Rushton turbines stirred bioreactor for different gas flow rates and impeller speeds. The hydrodynamic parameters like fractional gas hold-up, power consumption and mixing time have been measured. A two fluid model along with MUSIG model to handle polydispersed gas flow has been implemented to predict the various flow regimes and hydrodynamic parameters in the dual turbines stirred bioreactor. The computational model has been mapped on commercial solver ANSYS CFX. The flow regimes predicted by numerical simulations are validated with the experimental results. The present model has successfully captured the flow regimes as observed during experiments. The measured gross flow characteristics like fractional gas hold-up, and mixing time have been compared with numerical simulations. Also the effect of gas flow rate and impeller speed on gas hold-up and power consumption have been investigated. (c) 2009 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Rapid heating of Alaska pollock and chicken breast myofibrillar protein gels as affecting water-holding properties.

PubMed

Stevenson, Clinton D; Liu, Wenjie; Lanier, Tyre C

2012-10-10

The gelation response of salted muscle minces to rapid versus slow heating rates is thought to differ between homeotherm and poikilotherm species. This study investigated water-holding (WH) properties of pastes prepared from refined myofibrils, at equal pH, of chicken breast versus Alaska pollock both during [cook loss (CL)] and following [expressible water (EW)] their cooking by rapid [microwave (MW)] versus slow [water bath (WB)] heating and whether such properties were related to gel matrix structure parameters and water mobility. Results did not confirm the industrial experience that pastes of meat from homeotherms benefit from slower cooking. Gels of equally high WH ability (low CL or EW) were made by rapid heating when the holding time did not exceed 5 min prior to cooling, which was sufficient for completion of gelation. Reduced CL and EW correlated with larger and smaller amplitudes of T21 and T22 water pools, respectively, measured by time-domain nuclear magnetic resonance (TD-NMR).

Breath-hold times in air compared to breath-hold times during cold water immersions.

PubMed

Taber, Michael J; MacKinnon, Scott N; Power, Jonathan; Walker, Robert

2015-02-01

Given the effects of cold water immersion on breath-hold (BH) capabilities, a practical training exercise was developed for military/paramilitary personnel completing a helicopter underwater egress training (HUET) program. The exercise was designed to provide firsth and experience of the effects of cold water exposure on BH time. After completing the required HUET, 47 subjects completed two BH testing sessions as well as a short questionnaire. The first BH was completed while standing on the pool deck. The second BH was completed while fully immersed (face down) in 2-3°C water. There were 40 of the volunteers who also breathed from an emergency breathing system (EBS) while in the cold water. Results demonstrated that BH capabilities in cold water were significantly lower than those in ambient air. A significant correlation was also found between BH in air and the difference in cold water vs. air BH capabilities, which suggests that subjects who can hold their breath the longest in air experienced the greatest decrease in BH when immersed. Results indicate that 92% of the subjects reported that the practical cold water immersion exercise had a high value. Finally, 58% of those who used the EBS reported that it was harder to breathe in cold water than while in the training pool (approximately 22°C). The BH times for this group were similar to those reported in previous cold water immersion studies. Based on the questionnaire results, it is possible, when carefully applied, to include a practical cold water immersion exercise into existing HUET programs.

Stochastic thermodynamics of fluctuating density fields: Non-equilibrium free energy differences under coarse-graining

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leonard, T.; Lander, B.; Seifert, U.

2013-11-28

We discuss the stochastic thermodynamics of systems that are described by a time-dependent density field, for example, simple liquids and colloidal suspensions. For a time-dependent change of external parameters, we show that the Jarzynski relation connecting work with the change of free energy holds if the time evolution of the density follows the Kawasaki-Dean equation. Specifically, we study the work distributions for the compression and expansion of a two-dimensional colloidal model suspension implementing a practical coarse-graining scheme of the microscopic particle positions. We demonstrate that even if coarse-grained dynamics and density functional do not match, the fluctuation relations for themore » work still hold albeit for a different, apparent, change of free energy.« less

Electrical Evaluation of RCA MWS5501D Random Access Memory, Volume 2, Appendix a

NASA Technical Reports Server (NTRS)

Klute, A.

1979-01-01

The electrical characterization and qualification test results are presented for the RCA MWS5001D random access memory. The tests included functional tests, AC and DC parametric tests, AC parametric worst-case pattern selection test, determination of worst-case transition for setup and hold times, and a series of schmoo plots. The address access time, address readout time, the data hold time, and the data setup time are some of the results surveyed.

Connections between Future Time Perspectives and Self-Regulated Learning for Mid-Year Engineering Students: A Multiple Case Study

ERIC Educational Resources Information Center

Chasmar, Justine

2017-01-01

This dissertation presents multiple studies with the purpose of understanding the connections between undergraduate engineering students' motivations, specifically students' Future Time Perspectives (FTPs) and Self-Regulated Learning (SRL). FTP refers to the views students hold about the future and how their perceptions of current tasks are…

Deformation rate-, hold time-, and cycle-dependent shape-memory performance of Veriflex-E resin

NASA Astrophysics Data System (ADS)

McClung, Amber J. W.; Tandon, Gyaneshwar P.; Baur, Jeffery W.

2013-02-01

Shape-memory polymers have attracted great interest in recent years for application in reconfigurable structures (for instance morphing aircraft, micro air vehicles, and deployable space structures). However, before such applications can be attempted, the mechanical behavior of the shape-memory polymers must be thoroughly understood. The present study represents an assessment of viscous effects during multiple shape-memory cycles of Veriflex-E, an epoxy-based, thermally triggered shape-memory polymer resin. The experimental program is designed to explore the influence of multiple thermomechanical cycles on the shape-memory performance of Veriflex-E. The effects of the deformation rate and hold times at elevated temperature on the shape-memory behavior are also investigated.

Diving bradycardia of elderly Korean women divers, haenyeo, in cold seawater: a field report

PubMed Central

LEE, Joo-Young; LEE, Hyo-Hyun; KIM, Siyeon; JANG, Young-Joon; BAEK, Yoon-Jeong; KANG, Kwon-Yong

2015-01-01

The purpose of the present field study was to explore diving patterns and heart rate of elderly Korean women divers (haenyeo) while breath-hold diving in cold seawater. We hypothesized that the decreasing rate in heart rate of elderly haenyeos during breath-hold diving was greater and total diving time was shorter than those of young haenyeos from previous studies. Nine haenyeos participated in a field study [68 ± 10 yr in age, ranged from 56 to 83 yr] at a seawater temperature of 10 to 13 °C. Average total diving time including surface swimming time between dives was 253 ± 73 min (155–341 min). Total frequency of dives was 97 ± 28 times and they dived 23 ± 8 times per hour. All haenyeos showed diving bradycardia with a decreased rate of 20 ± 8% at the bottom time (101 ± 20 bpm) when compared to surface swimming time (125 ± 16 bpm) in the sea. Older haenyeos among the nine elderly haenyeos had shorter diving time, less diving frequencies, and lower heart rate at work (p<0.05). These reductions imply that haenyeos voluntarily adjust their workload along with advancing age and diminished cardiovascular functions. PMID:26632118

Diving bradycardia of elderly Korean women divers, haenyeo, in cold seawater: a field report.

PubMed

Lee, Joo-Young; Lee, Hyo-Hyun; Kim, Siyeon; Jang, Young-Joon; Baek, Yoon-Jeong; Kang, Kwon-Yong

2016-01-01

The purpose of the present field study was to explore diving patterns and heart rate of elderly Korean women divers (haenyeo) while breath-hold diving in cold seawater. We hypothesized that the decreasing rate in heart rate of elderly haenyeos during breath-hold diving was greater and total diving time was shorter than those of young haenyeos from previous studies. Nine haenyeos participated in a field study [68 ± 10 yr in age, ranged from 56 to 83 yr] at a seawater temperature of 10 to 13 °C. Average total diving time including surface swimming time between dives was 253 ± 73 min (155-341 min). Total frequency of dives was 97 ± 28 times and they dived 23 ± 8 times per hour. All haenyeos showed diving bradycardia with a decreased rate of 20 ± 8% at the bottom time (101 ± 20 bpm) when compared to surface swimming time (125 ± 16 bpm) in the sea. Older haenyeos among the nine elderly haenyeos had shorter diving time, less diving frequencies, and lower heart rate at work (p<0.05). These reductions imply that haenyeos voluntarily adjust their workload along with advancing age and diminished cardiovascular functions.

12 CFR 238.53 - Prescribed services and activities of savings and loan holding companies.

Code of Federal Regulations, 2014 CFR

2014-01-01

... reasons and the date by which the Board expects to act. (3)(i) Required time limit for System action. The... and loan holding companies. 238.53 Section 238.53 Banks and Banking FEDERAL RESERVE SYSTEM (CONTINUED) BOARD OF GOVERNORS OF THE FEDERAL RESERVE SYSTEM (CONTINUED) SAVINGS AND LOAN HOLDING COMPANIES...

12 CFR 238.53 - Prescribed services and activities of savings and loan holding companies.

Code of Federal Regulations, 2012 CFR

2012-01-01

... reasons and the date by which the Board expects to act. (3)(i) Required time limit for System action. The... and loan holding companies. 238.53 Section 238.53 Banks and Banking FEDERAL RESERVE SYSTEM (CONTINUED) BOARD OF GOVERNORS OF THE FEDERAL RESERVE SYSTEM (CONTINUED) SAVINGS AND LOAN HOLDING COMPANIES...

12 CFR 238.53 - Prescribed services and activities of savings and loan holding companies.

Code of Federal Regulations, 2013 CFR

2013-01-01

... reasons and the date by which the Board expects to act. (3)(i) Required time limit for System action. The... and loan holding companies. 238.53 Section 238.53 Banks and Banking FEDERAL RESERVE SYSTEM (CONTINUED) BOARD OF GOVERNORS OF THE FEDERAL RESERVE SYSTEM (CONTINUED) SAVINGS AND LOAN HOLDING COMPANIES...

78 FR 18973 - Bridgeline Holdings, L.P.; Notice of Petition for Rate Approval

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-28

... Holdings, L.P.; Notice of Petition for Rate Approval Take notice that on February 28, 2013, as supplemented on March 12, 2013, Bridgeline Holdings, L.P. filed for approval of rates for transportation services... TTY, call (202) 502-8659. Comment Date: 5:00 p.m. Eastern Time on Monday, April 1, 2013. Dated: March...

Transient Liquid-Phase Diffusion Bonding of Aluminum Metal Matrix Composite Using a Mixed Cu-Ni Powder Interlayer

NASA Astrophysics Data System (ADS)

Maity, Joydeep; Pal, Tapan Kumar

2012-07-01

In the present study, the transient liquid-phase diffusion bonding of an aluminum metal matrix composite (6061-15 wt.% SiCp) has been investigated for the first time using a mixed Cu-Ni powder interlayer at 560 °C, 0.2 MPa, for different holding times up to 6 h. The microstructure of the isothermally solidified zone contains equilibrium precipitate CuAl2, metastable precipitate Al9Ni2 in the matrix of α-solid solution along with the reinforcement particles (SiC). On the other hand, the microstructure of the central bond zone consists of equilibrium phases such as NiAl3, Al7Cu4Ni and α-solid solution along with SiC particles (without any segregation) and the presence of microporosities. During shear test, the crack originates from microporosities and propagates along the interphase interfaces resulting in poor bond strength for lower holding times. As the bonding time increases, with continual diffusion, the structural heterogeneity is diminished, and the microporosities are eliminated at the central bond zone. Accordingly, after 6-h holding, the microstructure of the central bond zone mainly consists of NiAl3 without any visible microporosity. This provides a joint efficiency of 84% with failure primarily occurring through decohesion at the SiC particle/matrix interface.

Canister cryogenic system for cooling germanium semiconductor detectors in borehole and marine probes

USGS Publications Warehouse

Boynton, G.R.

1975-01-01

High resolution intrinsic and lithium-drifted germanium gamma-ray detectors operate at about 77-90 K. A cryostat for borehole and marine applications has been designed that makes use of prefrozen propane canisters. Uses of such canisters simplifies cryostat construction, and the rapid exchange of canisters greatly reduces the time required to restore the detector to full holding-time capability and enhances the safety of a field operation where high-intensity 252Cf or other isotopic sources are used. A holding time of 6 h at 86 K was achieved in the laboratory in a simulated borehole probe in which a canister 3.7 cm diameter by 57 cm long was used. Longer holding times can be achieved by larger volume canisters in marine probes. ?? 1975.

The Satiating Properties of Pork are not Affected by Cooking Methods, Sousvide Holding Time or Mincing in Healthy Men—A Randomized Cross-Over Meal Test Study

PubMed Central

Kehlet, Ursula; Mitra, Bhaskar; Aaslyng, Margit D.

2017-01-01

Low temperature long time (LTLT) sous-vide cooking may modify meat proteins in a way that could promote satiety. We investigated the effects of (1) cooking method (LTLT 58 °C vs. oven 160 °C), (2) LTLT holding time (17 h vs. 72 min), and (3) pork structure, LTLT 58 °C for 17 h (minced vs. roast) on appetite regulation and in vitro protein digestibility. In a cross-over study, 37 healthy men consumed four meals containing pork: LTLT-cooked roast, 58 °C, 72 min; LTLT-cooked roast, 58 °C, 17 h; and, oven-cooked roast, 160 °C to a core temperature of 58 °C and LTLT-cooked minced patties, 58 °C, 17 h. Ad libitum energy intake (EI) after three hours was the primary endpoint. Moreover, subjective appetite sensations were assessed. Protein digestibility was determined in an in vitro simulated digestion model. Ad libitum EI did not differ between the meals. Furthermore, appetite ratings were not clearly affected. LTLT cooking for 72 min increased the proteolytic rate in the early gastric phase during digestion as compared to LTLT cooking for 17 h or oven cooking. In conclusion, LTLT cooking, LTLT holding time, and pork structure did not affect ad libitum EI. However, LTLT cooking at 58 °C for 72 min seemed to enhance in vitro protein digestibility. PMID:28846600

The Satiating Properties of Pork are not Affected by Cooking Methods, Sousvide Holding Time or Mincing in Healthy Men-A Randomized Cross-Over Meal Test Study.

PubMed

Kehlet, Ursula; Mitra, Bhaskar; Ruiz Carrascal, Jorge; Raben, Anne; Aaslyng, Margit D

2017-08-26

Low temperature long time (LTLT) sous-vide cooking may modify meat proteins in a way that could promote satiety. We investigated the effects of (1) cooking method (LTLT 58 °C vs. oven 160 °C), (2) LTLT holding time (17 h vs. 72 min), and (3) pork structure, LTLT 58 °C for 17 h (minced vs. roast) on appetite regulation and in vitro protein digestibility. In a cross-over study, 37 healthy men consumed four meals containing pork: LTLT-cooked roast, 58 °C, 72 min; LTLT-cooked roast, 58 °C, 17 h; and, oven-cooked roast, 160 °C to a core temperature of 58 °C and LTLT-cooked minced patties, 58 °C, 17 h. Ad libitum energy intake (EI) after three hours was the primary endpoint. Moreover, subjective appetite sensations were assessed. Protein digestibility was determined in an in vitro simulated digestion model. Ad libitum EI did not differ between the meals. Furthermore, appetite ratings were not clearly affected. LTLT cooking for 72 min increased the proteolytic rate in the early gastric phase during digestion as compared to LTLT cooking for 17 h or oven cooking. In conclusion, LTLT cooking, LTLT holding time, and pork structure did not affect ad libitum EI. However, LTLT cooking at 58 °C for 72 min seemed to enhance in vitro protein digestibility.

Variations the diameter tip of electrode on the resistance spot welding using electrode Cu on worksheet Fe

NASA Astrophysics Data System (ADS)

Baskoro, A. S.; Sugeng, S.; Sifa, Agus; Badruzzaman; Endramawan, Tito

2018-04-01

Resistance Spot Weld (RSW) is a welding technology which plays an important role that is often used in industry in large manufacturing industries, especially in the automotive sector, some of the parameters are affecting the welding process that give impact in the weld quality, diameter tip important impact on the resistance spot welding, This study can be categorized as experimental study by using Electrode material such as Cu and Fe Worksheet Materials, with a material thickness of 1 mm,0,8 mm, and 0,6 mm on each worksheet, and the large diameter of tip electrode (5√t) depend on the thickness of worksheet. Testing the material in the electrode and the worksheet by testing the composition and tensile test, and the hardness of the material used are to know the material used certainly. The result of the welding process was done by using the parameters voltage of 8KV, with a duty cycle of 50% using a variation of the time 8s-10s, and variations the electrode tip diameter that are affected by the thickness of the worksheet 5\\sqrt{t}, plate thickness used 1 mm, 0,8 mm and 0,6 mm, so that the electrodes was used to a thickness of 1 mm diameter tip electrode 5 mm, thickness 0,8 mm with an electrode tip diameter 4,5 mm and a thickness 0,6 mm with an electrode diameter of 4 mm, with current welding parameter 8kVA, and variations in holding time 10s, 9s and 8s 50% duty cycle, then testing welds with the standard shear test refers ASTM A370-2012 with more results to a thickness of 0,6 has the ability to withstand greater load on the holding time 8s and 9s, 10s, to a thickness 0,8 mm and 1 mm shear test results demonstrate the ability to withstand loads on the holding time of 10s and 9s have a greater ability than 8s on worksheet that has thickness 1 mm at a holding time of 10s, and then Maximum shear test averaging of 36,41 N at a worksheet with a thickness of 0,8 mm (diameter tip 4,5 mm) at a holding time of 8s and a mean minimum shear stress of 23,73 N at worksheet that has thickness 0,6 mm (diameter tip 4 mm).

IN SITU BIOREMEDIATION IN A LANDFILL: HOLDING TIME STUDY OF LEACHATE CHEMICAL AND MICROBIAL PARAMETERS

EPA Science Inventory

Processing and analyzing solid waste samples from large and costly sampling events in a timely manner is often difficult. As part of a Cooperative Research and Development Agreement (CRADA), the U.S. EPA and Waste Management Inc. (WMI) are investigating the conversion of landfill...

Development of a versatile high-temperature short-time (HTST) pasteurization device for small-scale processing of cell culture medium formulations.

PubMed

Floris, Patrick; Curtin, Sean; Kaisermayer, Christian; Lindeberg, Anna; Bones, Jonathan

2018-07-01

The compatibility of CHO cell culture medium formulations with all stages of the bioprocess must be evaluated through small-scale studies prior to scale-up for commercial manufacturing operations. Here, we describe the development of a bespoke small-scale device for assessing the compatibility of culture media with a widely implemented upstream viral clearance strategy, high-temperature short-time (HTST) treatment. The thermal stability of undefined medium formulations supplemented with soy hydrolysates was evaluated upon variations in critical HTST processing parameters, namely, holding times and temperatures. Prolonged holding times of 43 s at temperatures of 110 °C did not adversely impact medium quality while significant degradation was observed upon treatment at elevated temperatures (200 °C) for shorter time periods (11 s). The performance of the device was benchmarked against a commercially available mini-pilot HTST system upon treatment of identical formulations on both platforms. Processed medium samples were analyzed by untargeted LC-MS/MS for compositional profiling followed by chemometric evaluation, which confirmed the observed degradation effects caused by elevated holding temperatures but revealed comparable performance of our developed device with the commercial mini-pilot setup. The developed device can assist medium optimization activities by reducing volume requirements relative to commercially available mini-pilot instrumentation and by facilitating fast throughput evaluation of heat-induced effects on multiple medium lots.

Nursing Positions

MedlinePlus

... breast with your other hand. The Clutch or Football Hold This is also a good position for ... same time may also choose this position. The football hold allows babies to take milk more easily — ...

Underwater study of arterial blood pressure in breath-hold divers.

PubMed

Sieber, Arne; L'abbate, Antonio; Passera, Mirko; Garbella, Erika; Benassi, Antonio; Bedini, Remo

2009-11-01

Knowledge regarding arterial blood pressure (ABP) values during breath-hold diving is scanty. It derives from a few reports of measurements performed at the water's surface, showing slight or no increase in ABP, and from a single study of two simulated deep breath-hold dives in a hyperbaric chamber. Simulated dives showed an increase in ABP to values considered life threatening by standard clinical criteria. For the first time, using a novel noninvasive subaquatic sphygmomanometer, we successfully measured ABP in 10 healthy elite breath-hold divers at a depth of 10 m of freshwater (mfw). ABP was measured in dry conditions, at the surface (head-out immersion), and twice at a depth of 10 mfw. Underwater measurements of ABP were obtained in all subjects. Each measurement lasted 50-60 s and was accomplished without any complications or diver discomfort. In the 10 subjects as a whole, mean ABP values were 124/93 mmHg at the surface and 123/94 mmHg at a depth of 10 mfw. No significant statistical differences were found when blood pressure measurements at the water surface were compared with breath-hold diving conditions at a depth of 10 mfw. No systolic blood pressure values >140 mmHg or diastolic blood pressure values >115 mmHg were recorded. In conclusion, direct measurements of ABP during apnea diving showed no or only mild increases in ABP. However, our results cannot be extended over environmental conditions different from those of the present study.

Real-time Raman spectroscopy of optically trapped living cells and organelles

NASA Astrophysics Data System (ADS)

Xie, Changan; Goodman, Charles; Dinno, Mumtaz A.; Li, Yong-Qing

2004-12-01

We report on real-time Raman spectroscopic studies of optically trapped living cells and organelles using an inverted confocal laser-tweezers-Raman-spectroscopy (LTRS) system. The LTRS system was used to hold a single living cell in a physiological solution or to hold a functional organelle within a living cell and consequently measured its Raman spectra. We have measured the changes in Raman spectra of a trapped yeast cell as the function of the temperature of the bathing solution and studied the irreversible cell degeneration during the heat denaturation. In addition, we measured the in-vitro Raman spectra of the nuclei within living pine cells and B. sporeformer, Strep. salivarius, and E. coli bacteria suspended in solution and showed the possibility of using LTRS system as a sensor for rapid identification of microbes in a fluid.

Analgesic effects of breast-feeding or pacifier use with maternal holding in term infants.

PubMed

Phillips, Raylene M; Chantry, Caroline J; Gallagher, Michael P

2005-01-01

First, to compare analgesic effects of breast-feeding versus pacifier use in newborn infants undergoing blood collection via heel sticks. Second, to compare analgesic effects of pacifier use with maternal holding versus nonmaternal holding. A prospective, randomized, controlled trial. Normal newborn nursery at academic teaching hospital. Full-term breast-feeding infants scheduled for routine newborn screening blood test via heel stick (n = 96). Interventions.-Infants randomized to 3 groups for analgesia: 1) breast-feeding, 2) pacifier use while held by mothers, 3) pacifier use while held by research assistants (nonmothers). Primary outcome was crying (percent of infants who cried during the procedure and mean percent of procedure time that infants cried). Secondary outcomes were physiologic measures. Fewer breast-feeding infants cried than infants using a pacifier while held by nonmothers both during the procedure (69% vs 100%, P < .01) and after the procedure (28% vs 60%, P = .03). Those infants crying during the procedure cried for less time if held by their mothers either breast-feeding (33%, P < .01) or using a pacifier (45%, P = .03) than those using a pacifier while being held by nonmothers (66%). Breast-feeding is more analgesic than pacifier use with nonmaternal holding. Maternal holding with either breast-feeding or pacifier use is more analgesic than nonmaternal holding with pacifier use, suggesting that maternal holding itself has an analgesic effect. Breast-feeding and maternal holding should be considered as pain-control measures for the neonate during heel-stick procedures.

3D Late Gadolinium Enhancement in a Single Prolonged Breath-hold using Supplemental Oxygenation and Hyperventilation

PubMed Central

Roujol, Sébastien; Basha, Tamer A.; Akçakaya, Mehmet; Foppa, Murilo; Chan, Raymond H.; Kissinger, Kraig V.; Goddu, Beth; Berg, Sophie; Manning, Warren J.; Nezafat, Reza

2013-01-01

Purpose: To evaluate the feasibility of 3D single breath-hold late gadolinium enhancement (LGE) of the left ventricle (LV) using supplemental oxygen and hyperventilation and compressed-sensing acceleration. Methods: Breath-hold metrics (breath-hold duration, diaphragmatic/LV position drift, and maximum variation of RR interval) without and with supplemental oxygen and hyperventilation were assessed in healthy adult subjects using a real time single shot acquisition. Ten healthy subjects and 13 patients then underwent assessment of the proposed 3D breath-hold LGE acquisition (FOV=320×320×100 mm3, resolution=1.6×1.6×5.0 mm3, acceleration rate of 4) and a free breathing acquisition with right hemidiaphragm navigator (NAV) respiratory gating. Semi-quantitative grading of overall image quality, motion artifact, myocardial nulling, and diagnostic value was performed by consensus of two blinded observers. Results: Supplemental oxygenation and hyperventilation increased the breath-hold duration (35±11 s to 58±21 s, p<0.0125) without significant impact on diaphragmatic/LV position drift or maximum variation of RR interval (both p>0.01). LGE images were of similar quality when compared to free breathing acquisitions but with reduced total scan time (85±22 s to 35±6 s, p<0.001). Conclusions: Supplemental oxygenation and hyperventilation allow for prolonged breath-holding and enable single breath-hold 3D accelerated LGE with similar image quality as free breathing with NAV. PMID:24186772

Linkages between Youth Diversity and Organizational and Program Characteristics of Out-of-School-Time Science Programs: A Mixed-Methods Study

ERIC Educational Resources Information Center

Thiry, Heather; Archie, Timothy; Arreola-Pena, Melissa; Laursen, Sandra

2017-01-01

Science opportunities in out-of-school time (OST) programs hold potential for expanding access to science, engineering, and technology (SET) pathways for populations that have not participated in these fields at equitable rates (Coalition for Science After School, 2014). This mixed-methods study examines the relationship between the diversity of…

Organometallic exposure dependence on organic–inorganic hybrid material formation in polyethylene terephthalate and polyamide 6 polymer fibers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Akyildiz, Halil I.; Jur, Jesse S., E-mail: jsjur@ncsu.edu

2015-03-15

The effect of exposure conditions and surface area on hybrid material formation during sequential vapor infiltrations of trimethylaluminum (TMA) into polyamide 6 (PA6) and polyethylene terephthalate (PET) fibers is investigated. Mass gain of the fabric samples after infiltration was examined to elucidate the reaction extent with increasing number of sequential TMA single exposures, defined as the times for a TMA dose and a hold period. An interdependent relationship between dosing time and holding time on the hybrid material formation is observed for TMA exposure PET, exhibited as a linear trend between the mass gain and total exposure (dose time ×more » hold time × number of sequential exposures). Deviation from this linear relationship is only observed under very long dose or hold times. In comparison, amount of hybrid material formed during sequential exposures to PA6 fibers is found to be highly dependent on amount of TMA dosed. Increasing the surface area of the fiber by altering its cross-sectional dimension is shown to have little on the reaction behavior but does allow for improved diffusion of the TMA into the fiber. This work allows for the projection of exposure parameters necessary for future high-throughput hybrid modifications to polymer materials.« less

Effect of high-pressure processing on reduction of Listeria monocytogenes in packaged Queso Fresco.

PubMed

Tomasula, P M; Renye, J A; Van Hekken, D L; Tunick, M H; Kwoczak, R; Toht, M; Leggett, L N; Luchansky, J B; Porto-Fett, A C S; Phillips, J G

2014-03-01

The effect of high-hydrostatic-pressure processing (HPP) on the survival of a 5-strain rifampicin-resistant cocktail of Listeria monocytogenes in Queso Fresco (QF) was evaluated as a postpackaging intervention. Queso Fresco was made using pasteurized, homogenized milk, and was starter-free and not pressed. In phase 1, QF slices (12.7 × 7.6 × 1 cm), weighing from 52 to 66 g, were surface inoculated with L. monocytogenes (ca. 5.0 log10 cfu/g) and individually double vacuum packaged. The slices were then warmed to either 20 or 40°C and HPP treated at 200, 400, and 600 MPa for hold times of 5, 10, 15, or 20 min. Treatment at 600 MPa was most effective in reducing L. monocytogenes to below the detection level of 0.91 log10 cfu/g at all hold times and temperatures. High-hydrostatic-pressure processing at 40°C, 400 MPa, and hold time ≥ 15 min was effective but resulted in wheying-off and textural changes. In phase 2, L. monocytogenes was inoculated either on the slices (ca. 5.0 log10 cfu/g; ON) or in the curds (ca. 7.0 log10 cfu/g; IN) before the cheese block was formed and sliced. The slices were treated at 20°C and 600 MPa at hold times of 3, 10, and 20 min, and then stored at 4 and 10°C for 60 d. For both treatments, L. monocytogenes became less resistant to pressure as hold time increased, with greater percentages of injured cells at 3 and 10 min than at 20 min, at which the lethality of the process increased. For the IN treatment, with hold times of 3 and 10 min, growth of L. monocytogenes increased the first week of storage, but was delayed for 1 wk, with a hold time of 20 min. Longer lag times in growth of L. monocytogenes during storage at 4°C were observed for the ON treatment at hold times of 10 and 20 min, indicating that the IN treatment may have provided a more protective environment with less injury to the cells than the ON treatment. Similarly, HPP treatment for 10 min followed by storage at 4°C was the best method for suppressing the growth of the endogenous microflora with bacterial counts remaining below the level of detection for 2 out of the 3 QF samples for up to 84 d. Lag times in growth were not observed during storage of QF at 10°C. Although HPP reduced L. monocytogenes immediately after processing, a second preservation technique is necessary to control growth of L. monocytogenes during cold storage. However, the results also showed that HPP would be effective for slowing the growth of microorganisms that can shorten the shelf life of QF. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Dosimetric comparison of moderate deep inspiration breath-hold and free-breathing intensity-modulated radiotherapy for left-sided breast cancer.

PubMed

Chi, F; Wu, S; Zhou, J; Li, F; Sun, J; Lin, Q; Lin, H; Guan, X; He, Z

2015-05-01

This study determined the dosimetric comparison of moderate deep inspiration breath-hold using active breathing control and free-breathing intensity-modulated radiotherapy (IMRT) after breast-conserving surgery for left-sided breast cancer. Thirty-one patients were enrolled. One free breathe and two moderate deep inspiration breath-hold images were obtained. A field-in-field-IMRT free-breathing plan and two field-in-field-IMRT moderate deep inspiration breath-holding plans were compared in the dosimetry to target volume coverage of the glandular breast tissue and organs at risks for each patient. The breath-holding time under moderate deep inspiration extended significantly after breathing training (P<0.05). There was no significant difference between the free-breathing and moderate deep inspiration breath-holding in the target volume coverage. The volume of the ipsilateral lung in the free-breathing technique were significantly smaller than the moderate deep inspiration breath-holding techniques (P<0.05); however, there was no significant difference between the two moderate deep inspiration breath-holding plans. There were no significant differences in target volume coverage between the three plans for the field-in-field-IMRT (all P>0.05). The dose to ipsilateral lung, coronary artery and heart in the field-in-field-IMRT were significantly lower for the free-breathing plan than for the two moderate deep inspiration breath-holding plans (all P<0.05); however, there was no significant difference between the two moderate deep inspiration breath-holding plans. The whole-breast field-in-field-IMRT under moderate deep inspiration breath-hold with active breathing control after breast-conserving surgery in left-sided breast cancer can reduce the irradiation volume and dose to organs at risks. There are no significant differences between various moderate deep inspiration breath-holding states in the dosimetry of irradiation to the field-in-field-IMRT target volume coverage and organs at risks. Copyright © 2015 Société française de radiothérapie oncologique (SFRO). Published by Elsevier SAS. All rights reserved.

26 CFR 53.4943-5 - Present holdings acquired by trust or a will.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 20-year first phase holding period) applies to an interest in a business enterprise acquired after..., and at all times thereafter, as if such interest were held on May 26, 1969. However the first phase... phase holding period. (See, however, section 4943(c)(6) and paragraph (b)(2) of § 53.4943-6 for the...

26 CFR 53.4943-5 - Present holdings acquired by trust or a will.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 20-year first phase holding period) applies to an interest in a business enterprise acquired after..., and at all times thereafter, as if such interest were held on May 26, 1969. However the first phase... phase holding period. (See, however, section 4943(c)(6) and paragraph (b)(2) of § 53.4943-6 for the...

32 CFR Appendix C to Part 989 - Procedures for Holding Public Hearings on Draft Environmental Impact Statements (EIS)

Code of Federal Regulations, 2010 CFR

2010-07-01

... chance to speak, when the hearing has culled a representative view of public opinion, or when the time... 32 National Defense 6 2010-07-01 2010-07-01 false Procedures for Holding Public Hearings on Draft..., App. C Appendix C to Part 989—Procedures for Holding Public Hearings on Draft Environmental Impact...

The relationship between visitor characteristics and learning-associated behaviors in a science museum discovery space

NASA Astrophysics Data System (ADS)

Lozowski Boisvert, Dorothy; Jochums Slez, Brenda

As informal educational institutions, science museums must do more than entertain and amaze visitors. Museum educators must design exhibits that attract and hold the attention of visitors long enough so that the visitors become engaged with the exhibits and learn from them. In order for museum educators to develop such exhibits, more information is needed about the variables associated with learning in museums. This study contributes to the growing body of knowledge on informal education by examining the relationship between visitor characteristics and attraction, holding power, and visitor engagement.One hundred fifty-four visitors to a science museum discovery space were observed as they interacted freely with the exhibits. Trained volunteers recorded the subjects' movements including the exhibits at which they stopped (attraction), the amount of time spent at each exhibit (holding power), and behaviors indicative of subjects' engagement levels with the exhibits. Data indicated significant differences between age group and the holding power of exhibits. Though not significant statistically, a similar trend was noted between age group and attraction and visitor engagement level. No significant differences were found between gender or social grouping and attraction, holding power, or engagement levels.

Six sigma in action. Case studies in quality put theory into practice.

PubMed

Scalise, Dagmara

2003-05-01

Case studies of four hospitals show how Six Sigma can be used for everything from reducing ED hold time to cutting down on medical errors. Our examples pinpoint the costs of implementation and the savings and other benefits derived.

Breath-hold imaging of the coronary arteries using Quiescent-Interval Slice-Selective (QISS) magnetic resonance angiography: pilot study at 1.5 Tesla and 3 Tesla.

PubMed

Edelman, Robert R; Giri, S; Pursnani, A; Botelho, M P F; Li, W; Koktzoglou, I

2015-11-23

Coronary magnetic resonance angiography (MRA) is usually obtained with a free-breathing navigator-gated 3D acquisition. Our aim was to develop an alternative breath-hold approach that would allow the coronary arteries to be evaluated in a much shorter time and without risk of degradation by respiratory motion artifacts. For this purpose, we implemented a breath-hold, non-contrast-enhanced, quiescent-interval slice-selective (QISS) 2D technique. Sequence performance was compared at 1.5 and 3 Tesla using both radial and Cartesian k-space trajectories. The left coronary circulation was imaged in six healthy subjects and two patients with coronary artery disease. Breath-hold QISS was compared with T2-prepared 2D balanced steady-state free-precession (bSSFP) and free-breathing, navigator-gated 3D bSSFP. Approximately 10 2.1-mm thick slices were acquired in a single ~20-s breath-hold using two-shot QISS. QISS contrast-to-noise ratio (CNR) was 1.5-fold higher at 3 Tesla than at 1.5 Tesla. Cartesian QISS provided the best coronary-to-myocardium CNR, whereas radial QISS provided the sharpest coronary images. QISS image quality exceeded that of free-breathing 3D coronary MRA with few artifacts at either field strength. Compared with T2-prepared 2D bSSFP, multi-slice capability was not restricted by the specific absorption rate at 3 Tesla and pericardial fluid signal was better suppressed. In addition to depicting the coronary arteries, QISS could image intra-cardiac structures, pericardium, and the aortic root in arbitrary slice orientations. Breath-hold QISS is a simple, versatile, and time-efficient method for coronary MRA that provides excellent image quality at both 1.5 and 3 Tesla. Image quality exceeded that of free-breathing, navigator-gated 3D MRA in a much shorter scan time. QISS also allowed rapid multi-slice bright-blood, diastolic phase imaging of the heart, which may have complementary value to multi-phase cine imaging. We conclude that, with further clinical validation, QISS might provide an efficient alternative to commonly used free-breathing coronary MRA techniques.

Transport of equine ovaries for assisted reproduction.

PubMed

Ribeiro, B I; Love, L B; Choi, Y H; Hinrichs, K

2008-10-01

Use of assisted reproduction to obtain foals from valuable mares post-mortem typically necessitates holding of ovaries during shipment to a laboratory. The present study evaluated whether holding ovaries briefly at a warm ( approximately 30 degrees C) temperature improves meiotic and developmental competence of oocytes, as determined after maturation in vitro and intracytoplasmic sperm injection. Ovaries were packaged in pairs in insulated containers, and held either at 24 or 25-35 degrees C for 4h, followed by cooling. Ovaries in both treatments were held for either a short (mean, 7-7.4h) or long (mean, 20.6-20.7h) duration before oocyte recovery. Control ovaries were collected en masse at the abattoir. The ovary temperature in this treatment slowly decreased to approximately 27 degrees C; oocyte recovery was performed after 3.5-7h total holding. There was no effect of temperature on oocyte meiotic or developmental competence within either treatment time period. Oocytes in the short duration holding group had similar meiotic competence to controls, but had a significantly decreased rate (P<0.05) of blastocyst development. Oocytes in the long duration holding group had decreased (P<0.05) meiotic competence and blastocyst development compared to controls. These findings indicate that storage of equine ovaries for only 7h may decrease blastocyst development, and that longer storage reduces both rate of oocyte maturation and blastocyst development. Further work is needed to determine if there is a critical time before 7h post-mortem by which equine oocytes should be recovered to maximize developmental competence.

Effect of Sr Additive Amount and Holding Time on Microstructure of A390 Aluminum Alloy

NASA Astrophysics Data System (ADS)

Zhang, J. H.; Xing, S. M.; Han, Q. Y.; Guo, Q.; Wang, R. F.

2017-11-01

The microstructure of A390 alloy under different Sr additive amounts and holding times was studied by means of direct reading spectrum analysis, energy spectrum analysis, optical microscope and electron microscope. The results show that Sr has a good modification to eutectic Si, while it has a negative effect on primary silicon. The Sr addition will increase the size of primary silicon. When the addition amount of Al-10Sr alloy is 0.6%, the modification of eutectic silicon is the optimum. The Sr has a short incubation period and a fine modification at 10min, but it is more serious burning rate in small furnace smelting, and the modification effect disappears basically after 100min.

The Problems of Land Consolidation: A Case Study of Taiwan

ERIC Educational Resources Information Center

Williams, Jack F.

1976-01-01

Problems of agricultural land consolidation, as illustrated by Taiwan's first 10-year land reform phase, include fragmentation of holdings, cost of consolidation, corruption and maladministration by government officials, and timing of operations. (AV)

Obstructive sleep apnea screening by NIRS imaging

NASA Astrophysics Data System (ADS)

Kashefi, Feraydune; Watenpaugh, Donald E.; Liu, Hanli

2007-02-01

This study aimed at determining cerebral hemodynamic parameters in human subjects during breath holding using near infrared spectroscopy (NIRS). Breath holding serves as a method of simulation OSA (Obstructive Sleep Apnea). Data was acquired non-invasively from 40 subjects, twenty OSA sufferers (10 females, 10 males, age 20-70 years), and twenty normal volunteers (10 females, 10 males, age 20-65 years). Measurements were conducted using a LED Imager (LEDI) during breath holding. In comparing OSA subjects with controls during breath holding, a consistent increase or even a decrease in oxy- ([O IIHb]), deoxy- ([HHb]), total hemoglobin ([tHb]) concentrations, and tissue hemoglobin oxygen saturation (SO II) in the regional brain tissue were observed. The LEDI probe consists of 4 sources and 10 detectors serving as 4 sets of 1 source and 4 detectors each. A three wavelength (730, 805, and 850 nm) LED was used and the wavelengths were switched sequentially. The distance between sources and the source-detector separation were 2.5 cm. Data acquisition consisted of three segments, baseline for one minute, followed by a period of breath holding, and then 2 minutes of recovery time. The duration of the breath holding was subject-dependent. Our investigation proves that NIR spectroscopy could be used as a tool for detecting cerebral hemodynamics and also serves as a method of screening patients with OSA.

Tactic changes in dusky frillgoby Bathygobius fuscus sneaker males: effects of body size and nest availability.

PubMed

Takegaki, T; Kaneko, T; Matsumoto, Y

2013-02-01

Field and laboratory studies were conducted to examine the effects of nest availability and body size on changes in male mating tactics from sneaking to nest-holding in the dusky frillgoby Bathygobius fuscus. In the field, the body size of nest-holding males decreased from early to mid-breeding season, suggesting the possibility of a change in the tactics of sneaker males to nest-holding. Many sneaker males did not use vacant spawning nests even when size-matched nests were available, but they continued to reproduce as sneakers. Similarly, in aquarium experiments with available vacant nests, some sneaker males became nest-holders irrespective of their body size, but some did not. These results showed that nest availability is not a limiting factor for changes in tactics by sneaker males in this species. Because tactic-unchanged sneaker males were co-housed with larger nest-holding males in the tanks, the body size of nearby nest-holding males may have affected the decision to change tactics for sneaker males. Moreover, smaller individuals among tactic-changed males tended to spend more time until spawning, probably because they had relatively larger costs and smaller benefits of reproduction as nest-holding males compared to larger males. © 2012 The Authors. Journal of Fish Biology © 2012 The Fisheries Society of the British Isles.

Spacing, Testing, and Feedback: Helping Students Overcome Forgetting

ERIC Educational Resources Information Center

Kapler, Irina V.; Cepeda, Nicholas J.; Weston, Tina

2012-01-01

How can students' forgetting be reduced? The spacing effect--a promising strategy from the field of cognitive psychology--might hold some of the answers. Research has demonstrated that information is remembered two to three times better if study sessions are spaced in time rather than massed together. The testing effect is another research-based…

How tight are beetle hugs? Attachment in mating leaf beetles

NASA Astrophysics Data System (ADS)

Voigt, Dagmar; Tsipenyuk, Alexey; Varenberg, Michael

2017-09-01

Similar to other leaf beetles, rosemary beetles Chrysolina americana exhibit a distinct sexual dimorphism in tarsal attachment setae. Setal discoid terminals occur only in males, and they have been previously associated with a long-term attachment to the female's back (elytra) during copulation and mate guarding. For the first time, we studied living males and females holding to female's elytra. Pull-off force measurements with a custom-made tribometer featuring a self-aligning sample holder confirmed stronger attachment to female elytra compared with glass in both males and females; corresponding to 45 and 30 times the body weight, respectively. In line with previous studies, males generated significantly higher forces than females on convex elytra and flat glass, 1.2 times and 6.8 times, respectively. Convex substrates like elytra seem to improve the attachment ability of rosemary beetles, because they can hold more strongly due to favourable shear angles of legs, tarsi and adhesive setae. A self-aligning sample holder is found to be suitable for running force measurement tests with living biological samples.

How tight are beetle hugs? Attachment in mating leaf beetles.

PubMed

Voigt, Dagmar; Tsipenyuk, Alexey; Varenberg, Michael

2017-09-01

Similar to other leaf beetles, rosemary beetles Chrysolina americana exhibit a distinct sexual dimorphism in tarsal attachment setae. Setal discoid terminals occur only in males, and they have been previously associated with a long-term attachment to the female's back (elytra) during copulation and mate guarding. For the first time, we studied living males and females holding to female's elytra. Pull-off force measurements with a custom-made tribometer featuring a self-aligning sample holder confirmed stronger attachment to female elytra compared with glass in both males and females; corresponding to 45 and 30 times the body weight, respectively. In line with previous studies, males generated significantly higher forces than females on convex elytra and flat glass, 1.2 times and 6.8 times, respectively. Convex substrates like elytra seem to improve the attachment ability of rosemary beetles, because they can hold more strongly due to favourable shear angles of legs, tarsi and adhesive setae. A self-aligning sample holder is found to be suitable for running force measurement tests with living biological samples.

Elementary ELA/Social Studies Integration: Challenges and Limitations

ERIC Educational Resources Information Center

Heafner, Tina L.

2018-01-01

Adding instructional time and holding teachers accountable for teaching social studies are touted as practical, logical steps toward reforming the age-old tradition of marginalization. This qualitative case study of an urban elementary school, examines how nine teachers and one administrator enacted district reforms that added 45 minutes to the…

The influence of printing parameters on cell survival rate and printability in microextrusion-based 3D cell printing technology.

PubMed

Zhao, Yu; Li, Yang; Mao, Shuangshuang; Sun, Wei; Yao, Rui

2015-11-02

Three-dimensional (3D) cell printing technology has provided a versatile methodology to fabricate cell-laden tissue-like constructs and in vitro tissue/pathological models for tissue engineering, drug testing and screening applications. However, it still remains a challenge to print bioinks with high viscoelasticity to achieve long-term stable structure and maintain high cell survival rate after printing at the same time. In this study, we systematically investigated the influence of 3D cell printing parameters, i.e. composition and concentration of bioink, holding temperature and holding time, on the printability and cell survival rate in microextrusion-based 3D cell printing technology. Rheological measurements were utilized to characterize the viscoelasticity of gelatin-based bioinks. Results demonstrated that the bioink viscoelasticity was increased when increasing the bioink concentration, increasing holding time and decreasing holding temperature below gelation temperature. The decline of cell survival rate after 3D cell printing process was observed when increasing the viscoelasticity of the gelatin-based bioinks. However, different process parameter combinations would result in the similar rheological characteristics and thus showed similar cell survival rate after 3D bioprinting process. On the other hand, bioink viscoelasticity should also reach a certain point to ensure good printability and shape fidelity. At last, we proposed a protocol for 3D bioprinting of temperature-sensitive gelatin-based hydrogel bioinks with both high cell survival rate and good printability. This research would be useful for biofabrication researchers to adjust the 3D bioprinting process parameters quickly and as a referable template for designing new bioinks.

3D late gadolinium enhancement in a single prolonged breath-hold using supplemental oxygenation and hyperventilation.

PubMed

Roujol, Sébastien; Basha, Tamer A; Akçakaya, Mehmet; Foppa, Murilo; Chan, Raymond H; Kissinger, Kraig V; Goddu, Beth; Berg, Sophie; Manning, Warren J; Nezafat, Reza

2014-09-01

To evaluate the feasibility of three-dimensional (3D) single breath-hold late gadolinium enhancement (LGE) of the left ventricle (LV) using supplemental oxygen and hyperventilation and compressed-sensing acceleration. Breath-hold metrics [breath-hold duration, diaphragmatic/LV position drift, and maximum variation of R wave to R wave (RR) interval] without and with supplemental oxygen and hyperventilation were assessed in healthy adult subjects using a real-time single shot acquisition. Ten healthy subjects and 13 patients then underwent assessment of the proposed 3D breath-hold LGE acquisition (field of view = 320 × 320 × 100 mm(3) , resolution = 1.6 × 1.6 × 5.0 mm(3) , acceleration rate of 4) and a free-breathing acquisition with right hemidiaphragm navigator (NAV) respiratory gating. Semiquantitative grading of overall image quality, motion artifact, myocardial nulling, and diagnostic value was performed by consensus of two blinded observers. Supplemental oxygenation and hyperventilation increased the breath-hold duration (35 ± 11 s to 58 ± 21 s; P < 0.0125) without significant impact on diaphragmatic/LV position drift or maximum variation of RR interval (both P > 0.01). LGE images were of similar quality when compared with free-breathing acquisitions, but with reduced total scan time (85 ± 22 s to 35 ± 6 s; P < 0.001). Supplemental oxygenation and hyperventilation allow for prolonged breath-holding and enable single breath-hold 3D accelerated LGE with similar image quality as free breathing with NAV. Copyright © 2013 Wiley Periodicals, Inc.

New Experimental Technique for Nodularity and Mg Fading Control in Compacted Graphite Iron Production on Laboratory Scale

NASA Astrophysics Data System (ADS)

Hernando, Juan Carlos; Domeij, Björn; González, Daniel; Amieva, José Manuel; Diószegi, Attila

2017-11-01

The narrow production window for compacted graphite iron material (CGI) drastically reduces the possibilities to produce it in small batches outside an industrial environment. This fact hinders laboratory-scale investigations on CGI solidification. This work presents a solution to that issue by introducing an experimental technique to produce graphitic cast iron of the main three families. Samples of a base hypereutectic spheroidal graphite iron (SGI) were re-melted in a resistance furnace under Ar atmosphere. Varying the holding time at 1723 K (1450 °C), graphitic irons ranging from spheroidal to lamellar were produced. Characterization of the graphite morphology evolution, in terms of nodularity as a function of holding time, is presented. The nodularity decay for the SGI region suggests a linear correlation with the holding time. In the CGI region, nodularity deterioration shows a slower rate, concluding with the sudden appearance of lamellar graphite. The fading process of magnesium, showing agreement with previous researchers, is described by means of empirical relations as a function of holding time and nodularity. The results on nodularity fade and number of nodules per unit area fade suggest that both phenomena occur simultaneously during the fading process of magnesium.

75 FR 15684 - Magnuson-Stevens Act Provisions; General Provisions for Domestic Fisheries; Application for...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-30

... in a holding study to allow time for oxytetracycline to mark calcified structures for age-growth... laboratory, and given an injection of oxytetracycline. Monkfish would be marked with oxytetracycline, and...

Breath-holding spells may be associated with maturational delay in myelination of brain stem.

PubMed

Vurucu, Sebahattin; Karaoglu, Abdulbaki; Paksu, Sukru M; Oz, Oguzhan; Yaman, Halil; Gulgun, Mustafa; Babacan, Oguzhan; Unay, Bulent; Akin, Ridvan

2014-02-01

To evaluate possible contribution of maturational delay of brain stem in the etiology of breath-holding spells in children using brain stem auditory evoked potentials. The study group included children who experienced breath-holding spells. The control group consisted of healthy age- and sex-matched children. Age, gender, type and frequency of spell, hemoglobin, and ferritin levels in study group and brain stem auditory evoked potentials results in both groups were recorded. Study group was statistically compared with control group for brain stem auditory evoked potentials. The mean age of study and control groups was 26.3 ± 14.6 and 28.9 ± 13.9 months, respectively. The III-V and I-V interpeak latencies were significantly prolonged in the study group compared with the control group (2.07 ± 0.2 milliseconds; 1.92 ± 0.13 milliseconds and 4.00 ± 0.27 milliseconds; 3.83 ± 0.19 milliseconds; P = 0.009 and P = 0.03, respectively). At the same time, III-V and I-V interpeak latencies of patients without anemia in the study group compared with those of control group were significantly prolonged (2.09 ± 0.24 milliseconds; 1.92 ± 0.13 milliseconds and 4.04 ± 0.28 milliseconds; 3.83 ± 0.19 milliseconds; P = 0.007 and P = 0.01, respectively). Our results consider that maturational delay in myelination of brain stem may have a role in the etiology of breath-holding spells in children.

Abdominal organ motion during inhalation and exhalation breath-holds: pancreatic motion at different lung volumes compared.

PubMed

Lens, Eelco; Gurney-Champion, Oliver J; Tekelenburg, Daniël R; van Kesteren, Zdenko; Parkes, Michael J; van Tienhoven, Geertjan; Nederveen, Aart J; van der Horst, Astrid; Bel, Arjan

2016-11-01

Contrary to what is commonly assumed, organs continue to move during breath-holding. We investigated the influence of lung volume on motion magnitude during breath-holding and changes in velocity over the duration of breath-holding. Sixteen healthy subjects performed 60-second inhalation breath-holds in room-air, with lung volumes of ∼100% and ∼70% of the inspiratory capacity, and exhalation breath-holds, with lung volumes of ∼30% and ∼0% of the inspiratory capacity. During breath-holding, we obtained dynamic single-slice magnetic-resonance images with a time-resolution of 0.6s. We used 2-dimensional image correlation to obtain the diaphragmatic and pancreatic velocity and displacement during breath-holding. Organ velocity was largest in the inferior-superior direction and was greatest during the first 10s of breath-holding, with diaphragm velocities of 0.41mm/s, 0.29mm/s, 0.16mm/s and 0.15mm/s during BH 100% , BH 70% , BH 30% and BH 0% , respectively. Organ motion magnitudes were larger during inhalation breath-holds (diaphragm moved 9.8 and 9.0mm during BH 100% and BH 70% , respectively) than during exhalation breath-holds (5.6 and 4.3mm during BH 30% and BH 0% , respectively). Using exhalation breath-holds rather than inhalation breath-holds and delaying irradiation until after the first 10s of breath-holding may be advantageous for irradiation of abdominal tumors. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Thermal inactivation of foot-and-mouth disease virus in milk using high-temperature, short-time pasteurization.

PubMed

Tomasula, P M; Kozempel, M F; Konstance, R P; Gregg, D; Boettcher, S; Baxt, B; Rodriguez, L L

2007-07-01

Previous studies of laboratory simulation of high temperature, short time pasteurization (HTST) to eliminate foot-and-mouth disease virus (FMDV) in milk have shown that the virus is not completely inactivated at the legal pasteurization minimum (71.7 degrees C/15 s) but is inactivated in a flow apparatus at 148 degrees C with holding times of 2 to 3 s. It was the intent of this study to determine whether HTST pasteurization conducted in a continuous-flow pasteurizer that simulates commercial operation would enhance FMDV inactivation in milk. Cows were inoculated in the mammary gland with the field strain of FMDV (01/UK). Infected raw whole milk and 2% milk were then pasteurized using an Arm-field pilot-scale, continuous-flow HTST pasteurizer equipped with a plate-and-frame heat exchanger and a holding tube. The milk samples, containing FMDV at levels of up to 10(4) plaque-forming units/mL, were pasteurized at temperatures ranging from 72 to 95 degrees C at holding times of either 18.6 or 36 s. Pasteurization decreased virus infectivity by 4 log10 to undetectable levels in tissue culture. However, residual infectivity was still detectable for selected pasteurized milk samples, as shown by intramuscular and intradermal inoculation of milk into naïve steers. Although HTST pasteurization did not completely inactivate viral infectivity in whole and 2% milk, possibly because a fraction of the virus was protected by the milk fat and the casein proteins, it greatly reduced the risk of natural transmission of FMDV by milk.

The Consequences of Official Labels: An Examination of the Rights Lost by the Mentally Ill and Mentally Incompetent Since 1989.

PubMed

Walker, Andrea M; Klein, Michael S; Hemmens, Craig; Stohr, Mary K; Burton, Velmer S

2016-04-01

This study presents a survey of state statutes which restrict the civil rights of persons with a mental illness or who have been declared mentally incompetent. Five civil rights (voting, holding public office, jury service, parenting, and marriage) are examined. The results of this study are compared with the results of studies conducted in 1989 and 1999 to determine what changes have occurred over time in the restriction of civil rights of those suffering from mental health problems. This comparison reveals that states continue to restrict the rights of the mentally ill and incompetent, and that there is a trend towards increased restriction of political rights, including the right to vote and hold public office.

Going through the Rites of Passage: Timing and Transition of Menarche, Childhood Sexual Abuse, and Anxiety Symptoms in Girls

ERIC Educational Resources Information Center

Natsuaki, Misaki N.; Leve, Leslie D.; Mendle, Jane

2011-01-01

Menarche is a discrete, transitional event that holds considerable personal, social, biological, and developmental significance. The present longitudinal study examined both the transition and timing of menarche on the trajectory of anxiety in girls with histories of childhood maltreatment (N = 93; 63% European American, 14% multiracial, 10%…

Effects of pretransport handling stress on physiological and behavioral response of ostriches.

PubMed

Bejaei, M; Cheng, K M

2014-05-01

Ostrich (Struthio camelus) production is a relatively young industry and there has been little research on ostrich welfare during pretransport handling and the transportation process. A heavy body with a high center of gravity makes ostriches' handling and transportation problems different from other livestock. The main objective of this study was to investigate the effects of the pretransport holding time duration on ostrich behavior and physiological responses. A second objective was to identify and validate behavioral indicator(s) that could be used to identify stressed birds during pretransport handling. Prior to shipping, twenty-four 2.5-yr-old ostriches were moved into a holding pen. Birds were then individually restrained, hooded, and walked from the holding pen (approximately 12 min/bird) to a sampling pen (visually isolated from the holding pen) where they were weighed and a 10-mL blood sample obtained. A second blood sample was taken from each bird after a 1,100-km transportation. Blood samples were analyzed for concentrations of blood metabolites, enzymes, corticosterone, and white blood cell and differential counts. Behavioral responses and physical damages of ostriches were also recorded before and after transport. Results indicated that birds that spent longer time in the pretransport holding pen had higher pretransport plasma concentrations of aspartate aminotransferase, alanine aminotransferase, sodium, and packed cell volume. Immobile sitting behavior, observed in 5 out of the last 11 birds handled, was positively correlated with higher pretransport handling stress, higher posttransport aspartate aminotransferase, alanine aminotransferase, creatine phosphokinase, and glucose concentrations, and transport losses. Knowledge of pretransport handling impacts on ostrich stress and availability of behavioral indicators (e.g., immobile sitting response) could be used to improve handing processes, thereby decreasing potential weight loss, injury, and mortality.

Courses for Disadvantaged Adults

ERIC Educational Resources Information Center

Brown, Michael Barratt

1976-01-01

Problems and needs of unprepared adult learners are identified and purposes and processes for programs designed to hold them and encourage them on to more systematic study are outlined. Includes description of released time and multi-media programs at Sheffield University Department of Extra Mural Studies for trade unionists and housewives. (JT)

Formation of solar cells based on Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3} (BST) ferroelectric thick film

DOE Office of Scientific and Technical Information (OSTI.GOV)

Irzaman,, E-mail: irzaman@yahoo.com; Syafutra, H., E-mail: irzaman@yahoo.com; Arif, A., E-mail: irzaman@yahoo.com

2014-02-24

Growth of Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3} (BST) 1 M thick films are conducted with variation of annealing hold time of 8 hours, 15 hours, 22 hours, and 29 hours at a constant temperature of 850 °C on p-type Si (100) substrate using sol-gel method then followed by spin coating process at 3000 rpm for 30 seconds. The BST thick film electrical conductivity is obtained to be 10{sup −5} to 10{sup −4} S/cm indicate that the BST thick film is classified as semiconductor material. The semiconductor energy band gap value of BST thick film based on annealing hold time of 8more » hours, 15 hours, 22 hours, and 29 hours are 2.58 eV, 3.15 eV, 3.2 eV and 2.62 eV, respectively. The I-V photovoltaic characterization shows that the BST thick film is potentially solar cell device, and in accordance to annealing hold time of 8 hours, 15 hours, 22 hours and 29 hours have respective solar cell energy conversion efficiencies of 0.343%, 0.399%, 0.469% and 0.374%, respectively. Optical spectroscopy shows that BST thick film solar cells with annealing hold time of 8 hours, 15 hours, and 22 hours absorb effectively light energy at wavelength of ≥ 700 nm. BST film samples with annealing hold time of 29 hours absorb effectively light energy at wavelength of ≤ 700 nm. The BST thick film refraction index is between 1.1 to 1.8 at light wavelength between ±370 to 870 nm.« less

The effect of CO2 on ventilation and breath-holding during exercise and while breathing through an added resistance.

PubMed

Clark, T J; Godfrey, S

1969-05-01

1. Ventilation was measured while subjects were made to rebreathe from a bag containing CO(2) and O(2) in order to expose them to a steadily rising CO(2) tension (P(CO2)). The object of the experiments was to determine the effect of a variety of stimuli upon the increase in ventilation and fall in breath-holding time which occurs in response to the rising P(CO2).2. Steady-state exercise at 200 kg.m/min resulted in a small fall in the slope of the ventilation-CO(2) response curve (S(V)) and a small, though not statistically significant, fall in the P(CO2) at which ventilation would be zero by extrapolation (B(V)). There was a marked fall in the slope of the breath-holding-CO(2) response curve (S(BH)) and an increase in the P(CO2) at which breath-holding time became zero by extrapolation (B(BH)).3. These results have been interpreted with the aid of a model of the control of breath-holding and it is suggested that there is no change in CO(2) sensitivity on exercise, either during rebreathing or breath-holding.4. An increase in the resistance to breathing caused a marked reduction in S(V) and B(V), but no change in the breath-holding-CO(2) response curve. These findings suggest that the flattening of the ventilation-CO(2) response curve is mechanical in origin and acute airway obstruction produces no change in CO(2) sensitivity.5. On the basis of these results, we suggest that more information about CO(2) sensitivity can be obtained by a combination of ventilation and breath-holding-CO(2) response curves.

Modification of Eccentric Gaze-Holding

NASA Technical Reports Server (NTRS)

Reschke, M. F.; Paloski, W. H.; Somers, J. T.; Leigh, R. J.; Wood, S. J.; Kornilova, L.

2006-01-01

Clear vision and accurate localization of objects in the environment are prerequisites for reliable performance of motor tasks. Space flight confronts the crewmember with a stimulus rearrangement that requires adaptation to function effectively with the new requirements of altered spatial orientation and motor coordination. Adaptation and motor learning driven by the effects of cerebellar disorders may share some of the same demands that face our astronauts. One measure of spatial localization shared by the astronauts and those suffering from cerebellar disorders that is easily quantified, and for which a neurobiological substrate has been identified, is the control of the angle of gaze (the "line of sight"). The disturbances of gaze control that have been documented to occur in astronauts and cosmonauts, both in-flight and postflight, can be directly related to changes in the extrinsic gravitational environment and intrinsic proprioceptive mechanisms thus, lending themselves to description by simple non-linear statistical models. Because of the necessity of developing robust normal response populations and normative populations against which abnormal responses can be evaluated, the basic models can be formulated using normal, non-astronaut test subjects and subsequently extended using centrifugation techniques to alter the gravitational and proprioceptive environment of these subjects. Further tests and extensions of the models can be made by studying abnormalities of gaze control in patients with cerebellar disease. A series of investigations were conducted in which a total of 62 subjects were tested to: (1) Define eccentric gaze-holding parameters in a normative population, and (2) explore the effects of linear acceleration on gaze-holding parameters. For these studies gaze-holding was evaluated with the subjects seated upright (the normative values), rolled 45 degrees to both the left and right, or pitched back 30 and 90 degrees. In a separate study the further effects of acceleration on gaze stability was examined during centrifugation (+2 G (sub x) and +2 G (sub z) using a total of 23 subjects. In all of our investigations eccentric gaze-holding was established by having the subjects acquire an eccentric target (+/-30 degrees horizontal, +/- 15 degrees vertical) that was flashed for 750 msec in an otherwise dark room. Subjects were instructed to hold gaze on the remembered position of the flashed target for 20 sec. Immediately following the 20 sec period, subjects were cued to return to the remembered center position and to hold gaze there for an additional 20 sec. Following this 20 sec period the center target was briefly flashed and the subject made any corrective eye movement back to the true center position. Conventionally, the ability to hold eccentric gaze is estimated by fitting the natural log of centripetal eye drifts by linear regression and calculating the time constant (G) of these slow phases of "gaze-evoked nystagmus". However, because our normative subjects sometimes showed essentially no drift (tau (sub c) = m), statistical estimation and inference on the effect of target direction was performed on values of the decay constant theta = 1/(tau (sub c)) which we found was well modeled by a gamma distribution. Subjects showed substantial variance of their eye drifts, which were centrifugal in approximately 20 % of cases, and > 40% for down gaze. Using the ensuing estimated gamma distributions, we were able to conclude that rightward and leftward gaze holding were not significantly different, but that upward gaze holding was significantly worse than downward (p<0.05). We also concluded that vertical gaze holding was significantly worse than horizontal (p<0.05). In the case of left and right roll, we found that both had a similar improvement to horizontal gaze holding (p<0.05), but didn't have a significant effect on vertical gaze holding. For pitch tilts, both tilt angles significantly decreased gaze-holding ility in all directions (p<0.05). Finally, we found that hyper-g centrifugation significantly decreased gaze holding ability in the vertical plane. The main findings of this study are as follows: (1) vertical gaze-holding is less stable than horizontal, (2) gaze-holding to upward targets is less stable than to downward targets, (3) tilt affects gaze holding, and (4) hyper-g affects gaze holding. This difference between horizontal and vertical gaze-holding may be ascribed to separate components of the velocity-to-position neural integrator for eye movements, and to differences in orbital mechanics. The differences between upward and downward gaze-holding may be ascribed to an inherent vertical imbalance in the vestibular system. Because whole body tilt and hyper-g affects gaze-holding, it is implied that the otolith organs have direct connections to the neural integrator and further studies of astronaut gaze-holding are warranted. Our statistical method for representing the range of normal eccentric gaze stability can be readily applied to normals who maybe exposed to environments which may modify the central integrator and require monitoring, and to evaluate patients with gaze-evoked nystagmus by comparing to the above established normative criteria.

Two Person Zero-Sum Semi-Markov Games with Unknown Holding Times Distribution on One Side: A Discounted Payoff Criterion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Minjarez-Sosa, J. Adolfo, E-mail: aminjare@gauss.mat.uson.mx; Luque-Vasquez, Fernando

This paper deals with two person zero-sum semi-Markov games with a possibly unbounded payoff function, under a discounted payoff criterion. Assuming that the distribution of the holding times H is unknown for one of the players, we combine suitable methods of statistical estimation of H with control procedures to construct an asymptotically discount optimal pair of strategies.

Effect of Stress-Strain Behavior on Low-Cycle Fatigue of Alpha-Beta Titanium Alloys.

DTIC Science & Technology

1980-11-21

and strain excursion, such a curve would appear to fit much of the high temperature hold-time data compiled by Krempl and Wundt [21]. Thus, it might...34Mechanische Relaxation von Kupfer-Einkristallen," Phys. Stat. Sol. 3, 111-120. 21. Krempl, E. and Wundt , B. M., (1971), Hold-Time Effects in High- Temperature Low-Cycle Fatigue, ASTM STP 489. 26 Low

Creep-fatigue of low cobalt superalloys

NASA Technical Reports Server (NTRS)

Halford, G. R.

1982-01-01

Testing for the low cycle fatigue and creep fatigue resistance of superalloys containing reduced amounts of cobalt is described. The test matrix employed involves a single high temperature appropriate for each alloy. A single total strain range, again appropriate to each alloy, is used in conducting strain controlled, low cycle, creep fatigue tests. The total strain range is based upon the level of straining that results in about 10,000 cycles to failure in a high frequency (0.5 Hz) continuous strain-cycling fatigue test. No creep is expected to occur in such a test. To bracket the influence of creep on the cyclic strain resistance, strain hold time tests with ore minute hold periods are introduced. One test per composition is conducted with the hold period in tension only, one in compression only, and one in both tension and compression. The test temperatures, alloys, and their cobalt compositions that are under study are given.

[Analysis of carbon balance and study on mechanism in anoxic-oxic-settling-anaerobic sludge reduction process].

PubMed

Zhai, Xiao-Min; Gao, Xu; Zhang, Man-Man; Jia, Li; Guo, Jin-Song

2012-07-01

In order to deeply explore the mechanism of sludge reduction in OSA system, carbon balance was performed in an anoxic-oxic-settling-anaerobic (A + OSA) system and a reference AO system to investigate effects of inserting a sludge holding tank in sludge cycle line on the sludge reduction process. Meanwhile, carbon mass change in each reaction unit was identified in terms of solid, liquid and gas phases. The causes of excess sludge reduction in A + OSA system were deduced. The carbon balance results show that when the hydraulic retention time in the sludge holding tank is 7.14 h, carbon percent in solid phase of the sludge reduction system is nearly 50% higher than that of the reference system, supporting the consequence that sludge reduction rate of 49.98% had been achieved. The insertion of a sludge holding tank in the sludge return circuit can be effective in sludge reduction. Carbon changes in each unit reveal that the amount of carbon consumed for biosynthesis in the anoxic and oxic tanks (main reaction zone) of the sludge reduction system is higher than in that of the reference system. Sludge decay is observed in the sludge holding tank. Furthermore, CH4 released from the sludge holding tank is significantly higher than that from the main reaction zone. The DGGE profiles show that there are hydrolytic-fermentative bacteria in the sludge holding tank related to sludge decay. The excess sludge reduction in the A + OSA system could be a result of the combination of sludge decay in the sludge holding tank and sludge compensatory growth in the main reaction cell.

Breath-hold [68Ga]DOTA-TOC PET/CT in neuroendocrine tumors: detection of additional lesions and effects on quantitative parameters.

PubMed

Zirnsak, Mariana; Bärwolf, Robert; Freesmeyer, Martin

2016-11-08

Respiratory motion during PET/CT acquisition generates artifacts in the form of breath-related blurring, which influences the lesion detectability and diagnostic accuracy. The goal of this study was to verify whether breath-hold [68Ga]DOTA-TOC PET/CT (bhPET) allows detection of additional foci compared to free-breathing PET/CT (fbPET), and to assess the impact of breath-holding on standard uptake values (SUV) and isocontoured volume (Vic40) in patients with neuroendocrine tumors (NET). Patients with NET (n=39) were included in this study. BhPET and fbPET characteristics of 96 lesions were compared, and correlated with standard contrast-enhanced (ce) CT and MRI for lesion verification. Quantitative parameters SUV (max and mean) and Vic40 were assessed for both methods and evaluated by linear regression and Spearman's correlation. The impact of lesion size, localization and time interval between investigations was also analyzed. bhPET identified one additional metastasis not seen at fbPET but visible at ceMRI. Another additional bhPET focus did not have a morphological correlate. At bhPET, the SUVmax and SUVmean proved significantly higher and the Vic40 significantly lower than at fbPET. Lesion size, localization and time intervals did not impact significantly on SUV or Vic40. Currently, routine use of breath-hold [68Ga]DOTA-TOC PET/CT cannot be recommended as only one additional lesion was identified. Therefore, bhPET has currently no indication in patients with NET. If technical improvements regarding PET/CT scanner sensitivity are available, bhPET should be reevaluated in the future.

Analysis of pulsed injection for microgravity receiver tank chilldown

NASA Astrophysics Data System (ADS)

Honkonen, Scott C.; Pietrzyk, Joe R.; Schuster, John R.

The dominant heat transfer mechanism during the hold phase of a tank chilldown cycle in a low-gravity environment is due to fluid motion persistence following the charge. As compared to the single-charge per vent cycle case, pulsed injection maintains fluid motion and the associated high wall heat transfer coefficients during the hold phase. As a result, the pulsed injection procedure appears to be an attractive method for reducing the time and liquid mass required to chill a tank. However, for the representative conditions considered, no significant benefit can be realized by using pulsed injection as compared to the single-charge case. A numerical model of the charge/hold/vent process was used to evaluate the pulsed injection procedure for tank chilldown in microgravity. Pulsed injection results in higher average wall heat transfer coefficients during the hold, as compared to the single-charge case. However, these high levels were not coincident with the maximum wall-to-fluid temperature differences, as in the single-charge case. For representative conditions investigated, the charge/hold/vent process is very efficient. A slightly shorter chilldown time was realized by increasing the number of pulses.

Time-dependent crack growth behavior of alloy 617 and alloy 230 at elevated temperatures

NASA Astrophysics Data System (ADS)

Roy, Shawoon Kumar

2011-12-01

Two Ni-base solid-solution-strengthened superalloys: INCONEL 617 and HAYNES 230 were studied to check sustained loading crack growth (SLCG) behavior at elevated temperatures appropriate for Next Generation Nuclear Plant (NGNP) applictaions with constant stress intensity factor (Kmax= 27.75 MPa✓m) in air. The results indicate a time-dependent rate controlling process which can be characterized by a linear elastic fracture mechanics (LEFM) parameter -- stress intensity factor (K). At elevated temperatures, the crack growth mechanism was best described using a damage zone concept. Based on results and study, SAGBOE (stress accelerated grain boundary oxidation embrittlement) is considered the primary reason for time-dependent SLCG. A thermodynamic equation was considered to correlate all the SLCG results to determine the thermal activation energy in the process. A phenomenological model based on a time-dependent factor was developed considering the previous researcher's time-dependent fatigue crack propagation (FCP) results and current SLCG results to relate cycle-dependent and time-dependent FCP for both alloys. Further study includes hold time (3+300s) fatigue testing and no hold (1s) fatigue testing with various load ratios (R) at 700°C with a Kmax of 27.75 MPa✓m. Study results suggest an interesting point: crack growth behavior is significantly affected with the change in R value in cycle-dependent process whereas in time-dependent process, change in R does not have any significant effect. Fractography study showed intergranular cracking mode for all time-dependent processes and transgranular cracking mode for cycle-dependent processes. In Alloy 230, SEM images display intergranular cracking with carbide particles, dense oxides and dimple mixed secondary cracks for time-dependent 3+300s FCP and SLCG test. In all cases, Alloy 230 shows better crack growth resistance compared to Alloy 617.

Does fault strengthening in laboratory rock friction experiments really depend primarily upon time and not slip?

NASA Astrophysics Data System (ADS)

Bhattacharya, Pathikrit; Rubin, Allan M.; Beeler, Nicholas M.

2017-08-01

The popular constitutive formulations of rate-and-state friction offer two end-member views on whether friction evolves only with slip (Slip law) or with time even without slip (Aging law). While rate stepping experiments show support for the Slip law, laboratory-observed frictional behavior near-zero slip rates has traditionally been inferred as supporting Aging law style time-dependent healing, in particular, from the slide-hold-slide experiments of Beeler et al. (1994). Using a combination of new analytical results and explicit numerical (Bayesian) inversion, we show instead that the slide-hold-slide data of Beeler et al. (1994) favor slip-dependent state evolution during holds. We show that, while the stiffness-independent rate of growth of peak stress (following reslides) with hold duration is a property shared by both the Aging and (under a more restricted set of parameter combinations) Slip laws, the observed stiffness dependence of the rate of stress relaxation during long holds is incompatible with the Aging law with constant rate-state parameters. The Slip law consistently fits the evolution of the stress minima at the end of the holds well, whether fitting jointly with peak stresses or otherwise. But neither the Aging nor Slip laws fit all the data well when a - b is constrained to values derived from prior velocity steps. We also attempted to fit the evolution of stress peaks and minima with the Kato-Tullis hybrid law and the shear stress-dependent Nagata law, both of which, even with the freedom of an extra parameter, generally reproduced the best Slip law fits to the data.

Development and initial assessment of objective fatigue measures for apple harvest work.

PubMed

Earle-Richardson, Giulia; Jenkins, Paul L; Strogatz, David; Bell, Erin M; May, John J

2006-11-01

Previous research has shown that neck, back and shoulder musculoskeletal strain is a major occupational health problem affecting migrant orchard harvest workers. Researchers seek to measure the effect of an ergonomic modification to the apple picking bucket on muscle fatigue, however objective measures for use in the orchard are not yet available. The purpose of this study is to develop simple back, shoulder or arm strength measures, which detect statistically significant drops in strength over one workday. Candidate muscle strength measures were piloted in the laboratory, adapted for the orchard and evaluated (n=102). Data were analyzed for morning to afternoon fatigue, and for correlation between fatigue score and hours worked. In the laboratory, the timed arm hold (35.7% time reduction, 95% CI: 21.81-49.61), and the timed spinal extension (31.8% time reduction, 95% CI: 23.54-39.96) showed significant fatigue. In the orchard (n=102), only the timed arm hold showed significant (11.4%, p<.0001) fatigue. The potential effect of field conditions and subject motivation on these results needs further exploration.

Effect of injection parameters on mechanical and physical properties of super ultra-thin wall propylene packaging by Taguchi method

NASA Astrophysics Data System (ADS)

Ginghtong, Thatchanok; Nakpathomkun, Natthapon; Pechyen, Chiravoot

2018-06-01

The parameters of the plastic injection molding process have been investigated for the manufacture of a 64 oz. ultra-thin polypropylene bucket. The 3 main parameters, such as injection speed, melting temperature, holding pressure, were investigated to study their effect on the physical appearance and compressive strength. The orthogonal array of Taguchi's L9 (33) was used to carry out the experimental plan. The physical properties were measured and the compressive strength was determined using linear regression analysis. The differential scanning calorimeter (DSC) was used to analyze the crystalline structure of the product. The optimization results show that the proposed approach can help engineers identify optimal process parameters and achieve competitive advantages of energy consumption and product quality. In addition, the injection molding of the product includes 24 mm of shot stroke, 1.47 mm position transfer, 268 rpm screw speed, injection speed 100 mm/s, 172 ton clamping force, 800 kgf holding pressure, 0.9 s holding time and 1.4 s cooling time, make the products in the shape and proportion of the product satisfactory. The parameters of influence are injection speed 71.07%, melting temperature 23.31% and holding pressure 5.62%, respectively. The compressive strength of the product was able to withstand a pressure of up to 839 N before the product became plastic. The low melting temperature was caused by the superior crystalline structure of the super-ultra-thin wall product which leads to a lower compressive strength.

Understanding the Association between Future Time Perspective and Self-Regulated Learning through the Lens of Self-Determination Theory

ERIC Educational Resources Information Center

de Bilde, Jerissa; Vansteenkiste, Maarten; Lens, Willy

2011-01-01

The present cross-sectional research examined a process underlying the positive association between holding an extended future time perspective (FTP) and learning outcomes through the lens of self-determination theory. High school students and university students (N = 275) participated in the study. It was found that students with an extended FTP…

The effects of a passive exoskeleton on muscle activity, discomfort and endurance time in forward bending work.

PubMed

Bosch, Tim; van Eck, Jennifer; Knitel, Karlijn; de Looze, Michiel

2016-05-01

Exoskeletons may form a new strategy to reduce the risk of developing low back pain in stressful jobs. In the present study we examined the potential of a so-called passive exoskeleton on muscle activity, discomfort and endurance time in prolonged forward-bended working postures. Eighteen subjects performed two tasks: a simulated assembly task with the trunk in a forward-bended position and static holding of the same trunk position without further activity. We measured the electromyography for muscles in the back, abdomen and legs. We also measured the perceived local discomfort. In the static holding task we determined the endurance, defined as the time that people could continue without passing a specified discomfort threshold. In the assembly task we found lower muscle activity (by 35-38%) and lower discomfort in the low back when wearing the exoskeleton. Additionally, the hip extensor activity was reduced. The exoskeleton led to more discomfort in the chest region. In the task of static holding, we observed that exoskeleton use led to an increase in endurance time from 3.2 to 9.7 min, on average. The results illustrate the good potential of this passive exoskeleton to reduce the internal muscle forces and (reactive) spinal forces in the lumbar region. However, the adoption of an over-extended knee position might be, among others, one of the concerns when using the exoskeleton. Copyright © 2015 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Impact of collection container material and holding times on sample integrity for mercury and methylmercury in water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Riscassi, Ami L; Miller, Carrie L; Brooks, Scott C

Mercury (Hg) and methylmercury (MeHg) concentrations in streamwater can vary on short timescales (hourly or less) during storm flow and on a diel cycle; the frequency and timing of sampling required to accurately characterize these dynamics may be difficult to accomplish manually. Automated sampling can assist in sample collection; however use has been limited for Hg and MeHg analysis due to stability concerns of trace concentrations during extended storage times. We examined the viability of using automated samplers with disposable low-density polyethylene (LDPE) sample bags to collect industrially contaminated streamwater for unfiltered and filtered Hg and MeHg analysis. Specifically wemore » investigated the effect of holding times ranging from hours to days on streamwater collected during baseflow and storm flow. Unfiltered and filtered Hg and MeHg concentrations decreased with increases in time prior to sample processing; holding times of 24 hours or less resulted in concentration changes (mean 11 7% different) similar to variability in duplicates collected manually during analogous field conditions (mean 7 10% different). Comparisons of samples collected with manual and automated techniques throughout a year for a wide range of stream conditions were also found to be similar to differences observed between duplicate grab samples. These results demonstrate automated sampling into LDPE bags with holding times of 24 hours or less can be effectively used to collect streamwater for Hg and MeHg analysis, and encourage the testing of these materials and methods for implementation in other aqueous systems where high-frequency sampling is warranted.« less

HOLDING TIME STUDY FOR FECALS/SALMONELLA & CONNECTING LANGUAGE FOR 503 REGULATIONS

EPA Science Inventory

Current federal regulations required monitoring for fecal coliforms or Salmonella in biosolids destined for land application. Methods used for analysis of fecal coliforms and Salmonella have been developed and are currently in use for quantification of these organisms. Recently c...

Mother- and Father-Preterm Infant Relationship in the Hospital Preterm Nursery.

ERIC Educational Resources Information Center

Levy-Shiff, Rachel; And Others

1989-01-01

Studied the relationships between Israeli mothers and fathers and their 38 preterm infants during hospitalization. Mothers engaged in more caregiving, talking, and holding during initial contacts than did fathers. But disparity in maternal and paternal interactions decreased with time. (RJC)

NextGen Flight Deck Surface Trajectory-Based Operations (STBO): Contingency Holds

NASA Technical Reports Server (NTRS)

Bakowski, Deborah Lee; Hooey, Becky Lee; Foyle, David C.; Wolter, Cynthia A.; Cheng, Lara W. S.

2013-01-01

The purpose of this pilot-in-the-loop taxi simulation was to investigate a NextGen Surface Trajectory-Based Operations (STBO) concept called "contingency holds." The contingency-hold concept parses a taxi route into segments, allowing an air traffic control (ATC) surface traffic management (STM) system to hold an aircraft when necessary for safety. Under nominal conditions, if the intersection or active runway crossing is clear, the hold is removed, allowing the aircraft to continue taxiing without slowing, thus improving taxi efficiency, while minimizing the excessive brake use, fuel burn, and emissions associated with stop-and-go taxi. However, when a potential traffic conflict exists, the hold remains in place as a fail-safe mechanism. In this departure operations simulation, the taxi clearance included a required time of arrival (RTA) to a specified intersection. The flight deck was equipped with speed-guidance avionics to aid the pilot in safely meeting the RTA. On two trials, the contingency hold was not released, and pilots were required to stop. On two trials the contingency hold was released 15 sec prior to the RTA, and on two trials the contingency hold was released 30 sec prior to the RTA. When the hold remained in place, all pilots complied with the hold. Results also showed that when the hold was released at 15-sec or 30-sec prior to the RTA, the 30-sec release allowed pilots to maintain nominal taxi speed, thus supporting continuous traffic flow; whereas, the 15-sec release did not. The contingency-hold concept, with at least a 30-sec release, allows pilots to improve taxiing efficiency by reducing braking, slowing, and stopping, but still maintains safety in that no pilots "busted" the clearance holds. Overall, the evidence suggests that the contingency-hold concept is a viable concept for optimizing efficiency while maintaining safety.

Effect of Holding Time on Surface Films Formed on Molten AZ91D Alloy Protected by Graphite Powder

NASA Astrophysics Data System (ADS)

Li, Weihong; Zhou, Jixue; Ma, Baichang; Wang, Jinwei; Wu, Jianhua; Yang, Yuansheng

2017-10-01

Graphite powder was adopted to prevent the AZ91D magnesium alloy from oxidizing during the melting and casting process. The microstructure of the resultant surface films formed at 973 K (700 °C) holding for 0, 15, 30, 45, and 60 minutes was investigated by scanning electron microscopy, energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD) after mechanical polishing and chemical etching. The results indicated that the surface films were composed of a protective layer and the underneath particles with different morphology. The protective layer was continuous with a thickness of 200 to 1000 nm mainly consisting of MgO, MgF2, and C, while the underneath particles mainly consisted of MgF2 and MgAl2O4. The surface films were the result of the interaction between the graphite powder, the melt, and the ambient atmosphere. The number and the size of the underneath particles, determining the thickness uniformity of the surface films, and the unevenness of the microsurface morphology increased with holding time. The mechanism of holding time on the resultant surface films was also discussed.

Low strain, long life creep fatigue of AF2-1DA and INCO 718

NASA Technical Reports Server (NTRS)

Thakker, A. B.; Cowles, B. A.

1983-01-01

Two aircraft turbine disk alloys, GATORIZED AF2-DA and INCO 718 were evaluated for their low strain long life creep-fatigue behavior. Static (tensile and creep rupture) and cyclic properties of both alloys were characterized. The cntrolled strain LCF tests were conducted at 760 C (1400 F) and 649 C (1200 F) for AF2-1DA and INCO 718, respectively. Hold times were varied for tensile, compressive and tensile/compressive strain dwell (relaxation) tests. Stress (creep) hold behavior of AF2-1DA was also evaluated. Generally, INCO 718 exhibited more pronounced reduction in cyclic life due to hold than AF2-1DA. The percent reduction in life for both alloys for strain dwell tests was greater at low strain ranges (longer life regime). Changing hold time from 0 to 0.5, 2.0 and 15.0 min. resulted in corresponding reductions in life. The continuous cycle and cyclic/dwell initiation failure mechanism was predominantly transgranular for AF2-1DA and intergranular for INCO 718.

Effect of Spheroidizing Annealing on Microstructure and Mechanical Properties of High-Carbon Martensitic Stainless Steel 8Cr13MoV

NASA Astrophysics Data System (ADS)

Yu, Wen-Tao; Li, Jing; Shi, Cheng-Bin; Zhu, Qin-Tian

2017-02-01

The effects of holding time during both austenitizing and spheroidizing on microstructure and mechanical properties of high-carbon martensitic stainless steel 8Cr13MoV were experimentally studied. The results showed that the amount of carbides and the proportion of fine carbides decrease first and then increase with the increase in austenitizing time ( t 1) in the case of short spheroidizing time ( t 2), whereas the amount of the lamellar carbides increases. In the case of long t 2, both the amount of carbides and the proportion of fine carbides decrease, and the amount of the lamellar carbides did not increase. The hardness of the steel decreases first and then increases with the increase of t 1. Under the conditions of different t 1, the change in the size of carbides and hardness of the steel show a same trend with the variation of t 2. The size of spheroidized carbides increases, whereas the hardness of the steel decreases with increasing t 2. The longer the holding time of austenitizing, the higher is the spheroidizing rate at the earlier stage. However, the spheroidizing rate shows an opposite trend with t 1 at the later stage of spheroidizing. The effect of cooling rate on microstructure is similar with t 2. With increasing cooling rate, the dimension of carbides became smaller, and the amount of lamellar carbides increased. The elongation of the sample fracture exhibits no corresponding relationship with holding time, whereas it is closely related to the precipitation of secondary carbides caused by the alloying elements segregation.

Frictional `non-aging' of fault mirror surfaces?: Insight from friction experiments on Carrara marble

NASA Astrophysics Data System (ADS)

Park, Y.; Ree, J. H.; Hirose, T.

2016-12-01

Mirror-like fault surfaces (or fault mirror: FM) have recently been suggested as a precursor of unstable slip (thus indicative of seismic slip). Frictional aging of fault surfaces (increase in static friction during interseismic period) is a common phenomenon of fault surfaces, resulting from increase in contact area or in bond strength between asperities with time. Despite the importance of FM in earthquake faulting, the frictional-aging behavior of FM has never been studied. To understand the frictional-aging behavior of FM, slide-hold-slide friction experiments were done on carbonate FM and powdered gouge of former carbonate FM (PG hereafter) using low-to-high-velocity-rotary-shear apparatus, at a slip rate of 1 μm s-1 a normal stress of 1.5 MPa, room temperature and room humidity condition. The sheared PG specimens showed a logarithmic positive relationship between static friction and holding time, consistent with Dieterich-type healing behavior. In contrast, the sheared FM specimens showed little effect of holding time on static friction. The slip surface of FM specimens consists of densely-packed and sintered nano-particles while that of PG specimens is composed of loose nano-particles. It has been known that yield strength of a material increases dramatically with size-decreasing grains being nano-particles. Since FM is a layer of densely-packed and sintered nanoparticles, enhanced strength of FM may inhibit growth of real contact area of fault surfaces during hold time. Furthermore, sintered particles composing FM have less pore space than loose gouge layer, and thus there would be a less chance of strengthening by pore space reduction, inter-particle meniscus formation or water adsorption onto the particles surface in the FM layer. Our preliminary result suggests that carbonate FM's may impede the recovery of fault strength during interseismic period, resulting in less possibility of earthquake nucleation. Reduced frictional healing may be a common phenomenon of FM's in other materials too once they are composed of sintered nano-particles.

Self-Protective Optimism: Children's Biased Beliefs about the Stability of Traits

ERIC Educational Resources Information Center

Diesendruck, Gil; Lindenbaum, Tali

2009-01-01

Studies indicate that children believe that positive behaviors are more likely than negative ones to remain stable across time and situations. The present study assessed whether children hold such optimism equally regarding their own vs. others' behavioral patterns. Thirty five-year-olds answered questions about the extent to which they viewed…

Techniques for Measuring Solubility and Electrical Conductivity in Molten Salts

NASA Astrophysics Data System (ADS)

Su, Shizhao; Villalon, Thomas; Pal, Uday; Powell, Adam

Eutectic MgF2-CaF2 based salt containing YF3, CaO and Al2O3 additions were used in this study. The electrical conductivity was measured as a function of temperature by a calibration-free coaxial electrode setup. The materials selection and setup design were optimized to accurately measure the electrical conductivity of the highly conductive molten salts (>1 S/cm). The solubility and diffusion behavior of alumina and zirconia in the molten salts were investigated by drawing and holding the molten salt for different lengths of time within capillary tubes made of alumina and zirconia, respectively. After the time-dependent high temperature holds, the samples were cooled and the solubility of the solute within the molten salt was determined using scanning electron microscopy, energy-dispersive X-ray spectroscopy analysis and wavelength-dispersive X-ray spectroscopy analysis.

Fatigue crack growth and low cycle fatigue of two nickel base superalloys

NASA Technical Reports Server (NTRS)

Stoloff, N. S.; Duquette, D. J.; Choe, S. J.; Golwalkar, S.

1983-01-01

The fatigue crack growth and low cycle fatigue behavior of two P/M superalloys, Rene 95 and Astroloy, in the hot isostatically pressed (HIP) condition, was determined. Test variables included frequency, temperature, environment, and hold times at peak tensile loads (or strains). Crack initiation sites were identified in both alloys. Crack growth rates were shown to increase in argon with decreasing frequency or with the imposition of hold times. This behavior was attributed to the effect of oxygen in the argon. Auger analyses were performed on oxide films formed in argon. Low cycle fatigue lives also were degraded by tensile hold, contrary to previous reports in the literature. The role of environment in low cycle fatigue behavior is discussed.

26 CFR 301.6231(d)-1 - Time for determining profits interest of partners for purposes of sections 6223(b) and 6231(a)(11).

Code of Federal Regulations, 2010 CFR

2010-04-01

... examples are as follows: Example 1. B holds an interest in partnership P through T, a pass-thru partner. P... year. As of the close of P's taxable year ending June 30, 2002, T holds an interest in P and B holds an interest in P through T. The profits interest held by B in P through T for that year is determined as of...

Low cycle fatigue and creep fatigue interaction behavior of 9Cr-0.5Mo-1.8W-V-Nb heat-resistant steel at high temperature

NASA Astrophysics Data System (ADS)

Wang, Xiaowei; Zhang, Wei; Gong, Jianming; Wahab, Magd Abdel

2018-07-01

In this paper, Low Cycle Fatigue (LCF) and Creep-Fatigue Interaction (CFI) behavior of 9Cr-0.5Mo-1.8 W-V-Nb heat-resistant steel (ASME Grade P92 steel) at elevated temperature of 600 °C are investigated. Strain controlled LCF tests are conducted in fully reversed triangular waveform at different strain amplitudes ranging from 0.2% to 0.8%. CFI tests are conducted at 0.4% strain amplitude in trapezoid waveform with tensile hold time varying from 1 min to 60 min and compressive hold time varying from 1 min to 10 min. During LCF and CFI loadings, the evolution of cyclic stress, mean stress and stress relaxation behavior are investigated. It turns out that the softening behavior and lifetime degradation are dependent on strain amplitude, hold time and hold direction. In addition, the microstructure evolution and fracture behavior are characterized by optical, scanning and transmission electron microscope. The initial rapid softening behavior is attributed to the quick elimination of low angle boundaries, whereas no obvious microstructure alteration appears in the stable stage. Fracture behavior analysis reveals creep voids in long-term CFI tests facilitates the initiation and propagation of secondary cracks. The different responses of outer surface oxidation layer during cycling provides an explanation for severer damage of compressive hold and also accounts for the observed various fracture behavior of failed samples.

A new method for measuring lung deposition efficiency of airborne nanoparticles in a single breath

NASA Astrophysics Data System (ADS)

Jakobsson, Jonas K. F.; Hedlund, Johan; Kumlin, John; Wollmer, Per; Löndahl, Jakob

2016-11-01

Assessment of respiratory tract deposition of nanoparticles is a key link to understanding their health impacts. An instrument was developed to measure respiratory tract deposition of nanoparticles in a single breath. Monodisperse nanoparticles are generated, inhaled and sampled from a determined volumetric lung depth after a controlled residence time in the lung. The instrument was characterized for sensitivity to inter-subject variability, particle size (22, 50, 75 and 100 nm) and breath-holding time (3-20 s) in a group of seven healthy subjects. The measured particle recovery had an inter-subject variability 26-50 times larger than the measurement uncertainty and the results for various particle sizes and breath-holding times were in accordance with the theory for Brownian diffusion and values calculated from the Multiple-Path Particle Dosimetry model. The recovery was found to be determined by residence time and particle size, while respiratory flow-rate had minor importance in the studied range 1-10 L/s. The instrument will be used to investigate deposition of nanoparticles in patients with respiratory disease. The fast and precise measurement allows for both diagnostic applications, where the disease may be identified based on particle recovery, and for studies with controlled delivery of aerosol-based nanomedicine to specific regions of the lungs.

The effects of mothers' past infant-holding preferences on their adult children's face processing lateralisation.

PubMed

Vervloed, Mathijs P J; Hendriks, Angélique W; van den Eijnde, Esther

2011-04-01

Face processing development is negatively affected when infants have not been exposed to faces for some time because of congenital cataract blocking all vision (Le Grand, Mondloch, Maurer, & Brent, 2001). It is not clear, however, whether more subtle differences in face exposure may also have an influence. The present study looked at the effect of the mother's preferred side of holding an infant, on her adult child's face processing lateralisation. Adults with a mother who had a left-arm preference for holding infants were compared with adults with a mother who had a right-arm holding preference. All participants were right-handed and had been exclusively bottle-fed during infancy. The participants were presented with two chimeric faces tests, one involving emotion and the other one gender. The left-arm held individuals showed a normal left-bias on the chimeric face tests, whereas the right-arm held individuals a significantly decreased left-bias. The results might suggest that reduced exposure to high quality emotional information on faces in infancy results in diminished right-hemisphere lateralisation for face processing. Copyright © 2011 Elsevier Inc. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ahn, K.J.; Seferis, J.C.; Pelton, T.

A compression to tension apparatus and a methodology capable of measuring prepreg tack have been analyzed in detail in order to establish fundamental material and operating characteristics. Both intrinsic and extrinsic parameters influencing prepreg tack were identified and analyzed using commercially available carbon fiber/epoxy prepregs and mechanical testing equipment. Two different factors, (1) contact (or wetting) area of adjacent prepreg plies and (2) viscoelastic properties of the prepreg, were found to control prepreg tack. At low temperatures, contact area was the main deformation controlling step, while at high temperatures, the viscoelastic property of the prepreg was found to be dominant.more » Both interlaminar and intralaminar deformations were observed depending on the prepreg systems examined as well as the operating conditions of the test. In addition, hold time, hold pressure, loading rate, resin content, and out-time were also found to affect prepreg tack. Energy of separation, which may be viewed as a descriptor of prepreg tack, was observed to increase with increasing hold time, hold pressure, and loading rate. Energy of separation also showed a maximum value at a specific resin content for a specific prepreg system, while it decreased with increasing prepreg out-time due to prepreg surface characteristic change rather than bulk physical aging. Conclusively, it was observed that prepreg tack must be viewed as an extrinsic, bulk, but surface-sensitive, viscoelastic property which depends on material as well as operating conditions.« less

12 CFR 575.11 - Operating restrictions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... stockholders other than its parent mutual holding company may repurchase any share of stock within one year of its date of issuance (which may include the time period the shares issued by the savings association were outstanding if the subsidiary holding company was formed after the initial issuance by the savings...

Navy Underway

Science.gov Websites

Change of Command DDG-51 Program Marks Start of Construction Milestones at BIW, HII 2017 Sailors of the Deployed NETSAFA Holds Change of Command Pacific Partnership 2018 Kicks-Off in Thailand for First Time Forrest Sherman Holds Change of Command Suicide Prevention: ASIST Course Teaches Service Members to

Swiveling Lathe Jaw Concept for Holding Irregular Pieces

NASA Technical Reports Server (NTRS)

David, J.

1966-01-01

Clamp holds irregularly shaped pieces in lathe chuck without damage and eliminates excessive time in selecting optimum mounting. Interchangeable jaws ride in standard jaw slots but swivel so that the jaw face bears evenly against the workpiece regardless of contour. The jaws can be used on both engine and turret lathes.

9 CFR 93.412 - Ruminant quarantine facilities.

Code of Federal Regulations, 2014 CFR

2014-01-01

... (HVAC) system capable of controlling and maintaining the ambient temperature, air quality, moisture, and... to lot-holding areas must not be recirculated or reused for other ventilation needs. HVAC systems for... at a time, each lot-holding area must have its own separate HVAC system that is designed to prevent...

Healing Voids In Interconnections In Integrated Circuits

NASA Technical Reports Server (NTRS)

Cuddihy, Edward F.; Lawton, Russell A.; Gavin, Thomas

1989-01-01

Unusual heat treatment heals voids in aluminum interconnections on integrated circuits (IC's). Treatment consists of heating IC to temperature between 200 degrees C and 400 degrees C, holding it at that temperature, and then plunging IC immediately into liquid nitrogen. Typical holding time at evaluated temperature is 30 minutes.

[Water-holding characteristics and accumulation amount of the litters under main forest types in Xinglong Mountain of Gansu, Northwest China].

PubMed

Wei, Qiang; Ling, Lei; Zhang, Guang-zhong; Yan, Pei-bin; Tao, Ji-xin; Chai, Chun-shan; Xue, Rui

2011-10-01

By the methods of field survey and laboratory soaking extraction, an investigation was conducted on the accumulation amount, water-holding capacity, water-holding rate, and water-absorption rate of the litters under six main forests (Picea wilsonii forest, P. wilsonii - Betula platyphlla forest, Populus davidiana - B. platyphlla forest, Cotonester multiglorus - Rosa xanthina shrubs, Pinus tabulaeformis forest, and Larix principis-rupprechtii forest) in Xinglong Mountain of Gansu. The accumulation amount of the litters under the forests was 13.40-46.32 t hm(-2), and in the order of P. tabulaeformis forest > P. wilsonii - B. platyphlla forest > L. principis-rupprechtii forest > P. wilsonii forest > C. multiglorus-R. xanthina shrubs > P. davidiana - B. platyphlla forest. The litter storage of coniferous forests was greater than that of broadleaved forests, and the storage percentage of semi-decomposed litters was all higher than that of un-decomposed litters. The maximum water-holding rate of the litters was 185.5%-303.6%, being the highest for L. principis-rupprechtii forest and the lowest for P. tabulaeformis forest. The litters' water-holding capacity changed logarithmically with their soaking time. For coniferous forests, un-decomposed litters had a lower water-holding rate than semi-decomposed litters; whereas for broadleaved forests, it was in adverse. The maximum water-holding capacity of the litters varied from 3.94 mm to 8.59 mm, and was in the order of P. tabulaeformis forest > L. principis-rupprechtii forest > P. wilsonii - B. platyphlla forest > P. wilsonii forest > C. multiglorus - R. xanthina shrubs > P. davidiana - B. platyphlla forest. The litters' water-holding capacity also changed logarithmically with immersing time, and the half-decomposed litters had a larger water-holding capacity than un-decomposed litters. The water-absorption rate of the litters presented a power function with immersing time. Within the first one hour of immersed in water, the water-absorption rate of the litters declined linearly; after the first one hour, the litters' water-absorption rate became smaller, and changed slowly at different immersed stages. Semi-decomposed litters had a higher water-absorption rate than un-decomposed litters. The effective retaining amount (depth) of the litters was in the order of P. wilsonii - B. platyphlla forest (5.97 mm) > P. tabulaeformis forest (5.59 mm) > L. principis-rupprechtii forest (5.46 mm) >P. wilsonii forest (4.30 mm) > C. multiglorus - R. xanthina shrubs (3.03 mm)>P. davidiana - B. platyphlla forest (2.13 mm).

Surface Hold Advisor Using Critical Sections

NASA Technical Reports Server (NTRS)

Law, Caleb Hoi Kei (Inventor); Hsiao, Thomas Kun-Lung (Inventor); Mittler, Nathan C. (Inventor); Couluris, George J. (Inventor)

2013-01-01

The Surface Hold Advisor Using Critical Sections is a system and method for providing hold advisories to surface controllers to prevent gridlock and resolve crossing and merging conflicts among vehicles traversing a vertex-edge graph representing a surface traffic network on an airport surface. The Advisor performs pair-wise comparisons of current position and projected path of each vehicle with other surface vehicles to detect conflicts, determine critical sections, and provide hold advisories to traffic controllers recommending vehicles stop at entry points to protected zones around identified critical sections. A critical section defines a segment of the vertex-edge graph where vehicles are in crossing or merging or opposite direction gridlock contention. The Advisor detects critical sections without reference to scheduled, projected or required times along assigned vehicle paths, and generates hold advisories to prevent conflicts without requiring network path direction-of-movement rules and without requiring rerouting, rescheduling or other network optimization solutions.

Critical Chain Exercises

ERIC Educational Resources Information Center

Doyle, John Kevin

2010-01-01

Critical Chains project management focuses on holding buffers at the project level vs. task level, and managing buffers as a project resource. A number of studies have shown that Critical Chain project management can significantly improve organizational schedule fidelity (i.e., improve the proportion of projects delivered on time) and reduce…

From Perception to Recognition Memory: Time Course and Lateralization of Neural Substrates of Word and Abstract Picture Processing

ERIC Educational Resources Information Center

Maillard, Louis; Barbeau, Emmanuel J.; Baumann, Cedric; Koessler, Laurent; Benar, Christian; Chauvel, Patrick; Liegeois-Chauvel, Catherine

2011-01-01

Through study of clinical cases with brain lesions as well as neuroimaging studies of cognitive processing of words and pictures, it has been established that material-specific hemispheric specialization exists. It remains however unclear whether such specialization holds true for all processes involved in complex tasks, such as recognition…

You and the Civil Air Patrol.

DTIC Science & Technology

1988-04-01

currently holds the rank of Major In CAP. He was the Director of Senior Programs for the National Capital Wing for three years. In this capacity, he...2 Assumptions and Limitations ............................ 2 Previous Studies...................................... 2 CHAPTER TWO... limited thereby contributing to the problem. ASSUMPTIONS AND LIMITATIONS The time limitation and limited scope of this study prevented surveying all the

Gaze‐evoked nystagmus induced by alcohol intoxication

PubMed Central

Tarnutzer, Alexander A.; Straumann, Dominik; Ramat, Stefano; Bertolini, Giovanni

2017-01-01

Key points The cerebellum is the core structure controlling gaze stability. Chronic cerebellar diseases and acute alcohol intoxication affect cerebellar function, inducing, among others, gaze instability as gaze‐evoked nystagmus.Gaze‐evoked nystagmus is characterized by increased centripetal eye‐drift. It is used as an important diagnostic sign for patients with cerebellar degeneration and to assess the ‘driving while intoxicated’ condition.We quantified the effect of alcohol on gaze‐holding using an approach allowing, for the first time, the comparison of deficits induced by alcohol intoxication and cerebellar degeneration.Our results showed that alcohol intoxication induces a two‐fold increase of centripetal eye‐drift.We establish analysis techniques for using controlled alcohol intake as a model to support the study of cerebellar deficits.The observed similarity between the effect of alcohol and the clinical signs observed in cerebellar patients suggests a possible pathomechanism for gaze‐holding deficits. Abstract Gaze‐evoked nystagmus (GEN) is an ocular‐motor finding commonly observed in cerebellar disease, characterized by increased centripetal eye‐drift with centrifugal correcting saccades at eccentric gaze. With cerebellar degeneration being a rare and clinically heterogeneous disease, data from patients are limited. We hypothesized that a transient inhibition of cerebellar function by defined amounts of alcohol may provide a suitable model to study gaze‐holding deficits in cerebellar disease. We recorded gaze‐holding at varying horizontal eye positions in 15 healthy participants before and 30 min after alcohol intake required to reach 0.6‰ blood alcohol content (BAC). Changes in ocular‐motor behaviour were quantified measuring eye‐drift velocity as a continuous function of gaze eccentricity over a large range (±40 deg) of horizontal gaze angles and characterized using a two‐parameter tangent model. The effect of alcohol on gaze stability was assessed analysing: (1) overall effects on the gaze‐holding system, (2) specific effects on each eye and (3) differences between gaze angles in the temporal and nasal hemifields. For all subjects, alcohol consumption induced gaze instability, causing a two‐fold increase [2.21 (0.55), median (median absolute deviation); P = 0.002] of eye‐drift velocity at all eccentricities. Results were confirmed analysing each eye and hemifield independently. The alcohol‐induced transient global deficit in gaze‐holding matched the pattern previously described in patients with late‐onset cerebellar degeneration. Controlled intake of alcohol seems a suitable disease model to study cerebellar GEN. With alcohol resulting in global cerebellar hypofunction, we hypothesize that patients matching the gaze‐holding behaviour observed here suffered from diffuse deficits in the gaze‐holding system as well. PMID:27981586

Public Hearing, National Education Commission on Time and Learning: The Extended School Program and Its Impact on the Community. Southeastern Regional Hearing Summary (2nd, Murfreesboro, Tennessee, October 22, 1992).

ERIC Educational Resources Information Center

National Education Commission on Time and Learning, Washington, DC.

The National Education Commission on Time and Learning (NECT&L) is authorized by Public Law 102-62, the Education Council Act of 1991. The Commission is holding a series of hearings across the United States to examine the quality and adequacy of study and learning time of elementary and secondary students. This paper summarizes the evening…

Hybrid cardiac imaging with MR-CAT scan: a feasibility study.

PubMed

Hillenbrand, C; Sandstede, J; Pabst, T; Hahn, D; Haase, A; Jakob, P M

2000-06-01

We demonstrate the feasibility of a new versatile hybrid imaging concept, the combined acquisition technique (CAT), for cardiac imaging. The cardiac CAT approach, which combines new methodology with existing technology, essentially integrates fast low-angle shot (FLASH) and echoplanar imaging (EPI) modules in a sequential fashion, whereby each acquisition module is employed with independently optimized imaging parameters. One important CAT sequence optimization feature is the ability to use different bandwidths for different acquisition modules. Twelve healthy subjects were imaged using three cardiac CAT acquisition strategies: a) CAT was used to reduce breath-hold duration times while maintaining constant spatial resolution; b) CAT was used to increase spatial resolution in a given breath-hold time; and c) single-heart beat CAT imaging was performed. The results obtained demonstrate the feasibility of cardiac imaging using the CAT approach and the potential of this technique to accelerate the imaging process with almost conserved image quality. Copyright 2000 Wiley-Liss, Inc.

Nonflammable Hydraulic Power System for Tactical Aircraft. Volume 2. Equipment and Systems Test and Evaluation.

DTIC Science & Technology

1991-04-01

hold large quantities of air in solution at high pressures and at 8000 psi CTFE holds 500 times its volume of standard atmospheric air. Since air...cart bleeding can be expected to reduce dissolved air to about 1.5 times the amount held at atmospheric pressure. This is more than adequate for...aircraft hydraulic systems while circulating fluid through the cart reservoir which is vented to atmosphere . After open loop air bleeding, the aircraft

The effect of hold-times on the fatigue life of 20% cold-worked Type 316L stainless steel under deuteron irradiation

NASA Astrophysics Data System (ADS)

Scholz, R.

1995-09-01

Strain-controlled fatigue tests have been performed in torsion on 20% cold-worked Type 316L stainless steel specimens during irradiation with 19 MeV deuterons. A hold-time was imposed at the minimum strain value in the loading cycle. The irradiation creep induced stress relaxation led to the buildup of a mean stress. The number of cycles to failure may be significantly reduced in comparison to analogous continuous cycling tests under thermal conditions.

A real-time respiration position based passive breath gating equipment for gated radiotherapy: A preclinical evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hu Weigang; Xu Anjie; Li Guichao

2012-03-15

Purpose: To develop a passive gating system incorporating with the real-time position management (RPM) system for the gated radiotherapy. Methods: Passive breath gating (PBG) equipment, which consists of a breath-hold valve, a controller mechanism, a mouthpiece kit, and a supporting frame, was designed. A commercial real-time positioning management system was implemented to synchronize the target motion and radiation delivery on a linear accelerator with the patient's breathing cycle. The respiratory related target motion was investigated by using the RPM system for correlating the external markers with the internal target motion while using PBG for passively blocking patient's breathing. Six patientsmore » were enrolled in the preclinical feasibility and efficiency study of the PBG system. Results: PBG equipment was designed and fabricated. The PBG can be manually triggered or released to block or unblock patient's breathing. A clinical workflow was outlined to integrate the PBG with the RPM system. After implementing the RPM based PBG system, the breath-hold period can be prolonged to 15-25 s and the treatment delivery efficiency for each field can be improved by 200%-400%. The results from the six patients showed that the diaphragm motion caused by respiration was reduced to less than 3 mm and the position of the diaphragm was reproducible for difference gating periods. Conclusions: A RPM based PBG system was developed and implemented. With the new gating system, the patient's breath-hold time can be extended and a significant improvement in the treatment delivery efficiency can also be achieved.« less

Sustained apnea induces endothelial activation.

PubMed

Eichhorn, Lars; Dolscheid-Pommerich, Ramona; Erdfelder, Felix; Ayub, Muhammad Ajmal; Schmitz, Theresa; Werner, Nikos; Jansen, Felix

2017-09-01

Apnea diving has gained worldwide popularity, even though the pathophysiological consequences of this challenging sport on the human body are poorly investigated and understood. This study aims to assess the influence of sustained apnea in healthy volunteers on circulating microparticles (MPs) and microRNAs (miRs), which are established biomarkers reflecting vascular function. Short intermittent hypoxia due to voluntary breath-holding affects circulating levels of endothelial cell-derived MPs (EMPs) and endothelial cell-derived miRs. Under dry laboratory conditions, 10 trained apneic divers performed maximal breath-hold. Venous blood samples were taken, once before and at 4 defined points in time after apnea. Samples were analyzed for circulating EMPs and endothelial miRs. Average apnea time was 329 seconds (±103), and SpO 2 at the end of apnea was 79% (±12). Apnea was associated with a time-dependent increase of circulating endothelial cell-derived EMPs and endothelial miRs. Levels of circulating EMPs in the bloodstream reached a peak 4 hours after the apnea period and returned to baseline levels after 24 hours. Circulating miR-126 levels were elevated at all time points after a single voluntary maximal apnea, whereas miR-26 levels were elevated significantly only after 30 minutes and 4 hours. Also miR-21 and miR-92 levels increased, but did not reach the level of significance. Even a single maximal breath-hold induces acute endothelial activation and should be performed with great caution by subjects with preexisting vascular diseases. Voluntary apnea might be used as a model to simulate changes in endothelial function caused by hypoxia in humans. © 2017 Wiley Periodicals, Inc.

Characteristics of Holding, Patterns of Play, and Social Behaviors between Parents and Infants in New Delhi, India.

ERIC Educational Resources Information Center

Roopnarine, Jaipaul L.; And Others

1990-01-01

Compared with fathers, mothers were more likely to pick up and hold infants, feed and comfort them, and invest time in displaying affection. Although there were sex differences in parents' rough and peek-a-boo play, mothers and fathers treated boys and girls quite similarly. (RH)

The Key for Holding a Successful ELT Conference: Some Nuts and Bolts

ERIC Educational Resources Information Center

Sadeghi, Karim; Modirkhameneh, Sima

2013-01-01

Conferences are gatherings that attract attendants from various places and serve both academic and social purposes. Organizing an international conference is, accordingly, a very challenging, demanding and time-consuming task. In order for the conference organizers to hold a successful conference, there is a need for a comprehensive guide to use…

31 CFR 316.5 - Limitation on holdings.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., DEPARTMENT OF THE TREASURY BUREAU OF THE FISCAL SERVICE OFFERING OF UNITED STATES SAVINGS BONDS, SERIES E § 316.5 Limitation on holdings. (a) General limitation. The amount of Series E bonds, originally issued... any employee savings plan, as defined in paragraph (b)(1) of this section, at any time during the year...

31 CFR 332.5 - Limitation on holdings.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., DEPARTMENT OF THE TREASURY BUREAU OF THE FISCAL SERVICE OFFERING OF UNITED STATES SAVINGS BONDS, SERIES H § 332.5 Limitation on holdings. The amount of Series H bonds, originally issued during any one calendar year, that could be held by any one person, at any one time, computed in accordance with the governing...

31 CFR 332.5 - Limitation on holdings.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., DEPARTMENT OF THE TREASURY BUREAU OF THE PUBLIC DEBT OFFERING OF UNITED STATES SAVINGS BONDS, SERIES H § 332.5 Limitation on holdings. The amount of Series H bonds, originally issued during any one calendar year, that could be held by any one person, at any one time, computed in accordance with the governing...

31 CFR 332.5 - Limitation on holdings.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., DEPARTMENT OF THE TREASURY BUREAU OF THE PUBLIC DEBT OFFERING OF UNITED STATES SAVINGS BONDS, SERIES H § 332.5 Limitation on holdings. The amount of Series H bonds, originally issued during any one calendar year, that could be held by any one person, at any one time, computed in accordance with the governing...

31 CFR 316.5 - Limitation on holdings.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., DEPARTMENT OF THE TREASURY BUREAU OF THE PUBLIC DEBT OFFERING OF UNITED STATES SAVINGS BONDS, SERIES E § 316.5 Limitation on holdings. (a) General limitation. The amount of Series E bonds, originally issued... any employee savings plan, as defined in paragraph (b)(1) of this section, at any time during the year...

31 CFR 332.5 - Limitation on holdings.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., DEPARTMENT OF THE TREASURY BUREAU OF THE PUBLIC DEBT OFFERING OF UNITED STATES SAVINGS BONDS, SERIES H § 332.5 Limitation on holdings. The amount of Series H bonds, originally issued during any one calendar year, that could be held by any one person, at any one time, computed in accordance with the governing...

31 CFR 332.5 - Limitation on holdings.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., DEPARTMENT OF THE TREASURY BUREAU OF THE PUBLIC DEBT OFFERING OF UNITED STATES SAVINGS BONDS, SERIES H § 332.5 Limitation on holdings. The amount of Series H bonds, originally issued during any one calendar year, that could be held by any one person, at any one time, computed in accordance with the governing...

31 CFR 316.5 - Limitation on holdings.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., DEPARTMENT OF THE TREASURY BUREAU OF THE PUBLIC DEBT OFFERING OF UNITED STATES SAVINGS BONDS, SERIES E § 316.5 Limitation on holdings. (a) General limitation. The amount of Series E bonds, originally issued... any employee savings plan, as defined in paragraph (b)(1) of this section, at any time during the year...

Flight Departure Delay and Rerouting Under Uncertainty in En Route Convective Weather

NASA Technical Reports Server (NTRS)

Mukherjee, Avijit; Grabbe, Shon; Sridhar, Banavar

2011-01-01

Delays caused by uncertainty in weather forecasts can be reduced by improving traffic flow management decisions. This paper presents a methodology for traffic flow management under uncertainty in convective weather forecasts. An algorithm for assigning departure delays and reroutes to aircraft is presented. Departure delay and route assignment are executed at multiple stages, during which, updated weather forecasts and flight schedules are used. At each stage, weather forecasts up to a certain look-ahead time are treated as deterministic and flight scheduling is done to mitigate the impact of weather on four-dimensional flight trajectories. Uncertainty in weather forecasts during departure scheduling results in tactical airborne holding of flights. The amount of airborne holding depends on the accuracy of forecasts as well as the look-ahead time included in the departure scheduling. The weather forecast look-ahead time is varied systematically within the experiments performed in this paper to analyze its effect on flight delays. Based on the results, longer look-ahead times cause higher departure delays and additional flying time due to reroutes. However, the amount of airborne holding necessary to prevent weather incursions reduces when the forecast look-ahead times are higher. For the chosen day of traffic and weather, setting the look-ahead time to 90 minutes yields the lowest total delay cost.

Self-Similar Random Process and Chaotic Behavior In Serrated Flow of High Entropy Alloys

PubMed Central

Chen, Shuying; Yu, Liping; Ren, Jingli; Xie, Xie; Li, Xueping; Xu, Ying; Zhao, Guangfeng; Li, Peizhen; Yang, Fuqian; Ren, Yang; Liaw, Peter K.

2016-01-01

The statistical and dynamic analyses of the serrated-flow behavior in the nanoindentation of a high-entropy alloy, Al0.5CoCrCuFeNi, at various holding times and temperatures, are performed to reveal the hidden order associated with the seemingly-irregular intermittent flow. Two distinct types of dynamics are identified in the high-entropy alloy, which are based on the chaotic time-series, approximate entropy, fractal dimension, and Hurst exponent. The dynamic plastic behavior at both room temperature and 200 °C exhibits a positive Lyapunov exponent, suggesting that the underlying dynamics is chaotic. The fractal dimension of the indentation depth increases with the increase of temperature, and there is an inflection at the holding time of 10 s at the same temperature. A large fractal dimension suggests the concurrent nucleation of a large number of slip bands. In particular, for the indentation with the holding time of 10 s at room temperature, the slip process evolves as a self-similar random process with a weak negative correlation similar to a random walk. PMID:27435922

Self-similar random process and chaotic behavior in serrated flow of high entropy alloys

DOE PAGES

Chen, Shuying; Yu, Liping; Ren, Jingli; ...

2016-07-20

Here, the statistical and dynamic analyses of the serrated-flow behavior in the nanoindentation of a high-entropy alloy, Al 0.5CoCrCuFeNi, at various holding times and temperatures, are performed to reveal the hidden order associated with the seemingly-irregular intermittent flow. Two distinct types of dynamics are identified in the high-entropy alloy, which are based on the chaotic time-series, approximate entropy, fractal dimension, and Hurst exponent. The dynamic plastic behavior at both room temperature and 200 °C exhibits a positive Lyapunov exponent, suggesting that the underlying dynamics is chaotic. The fractal dimension of the indentation depth increases with the increase of temperature, andmore » there is an inflection at the holding time of 10 s at the same temperature. A large fractal dimension suggests the concurrent nucleation of a large number of slip bands. In particular, for the indentation with the holding time of 10 s at room temperature, the slip process evolves as a self-similar random process with a weak negative correlation similar to a random walk.« less

Self-Similar Random Process and Chaotic Behavior In Serrated Flow of High Entropy Alloys.

PubMed

Chen, Shuying; Yu, Liping; Ren, Jingli; Xie, Xie; Li, Xueping; Xu, Ying; Zhao, Guangfeng; Li, Peizhen; Yang, Fuqian; Ren, Yang; Liaw, Peter K

2016-07-20

The statistical and dynamic analyses of the serrated-flow behavior in the nanoindentation of a high-entropy alloy, Al0.5CoCrCuFeNi, at various holding times and temperatures, are performed to reveal the hidden order associated with the seemingly-irregular intermittent flow. Two distinct types of dynamics are identified in the high-entropy alloy, which are based on the chaotic time-series, approximate entropy, fractal dimension, and Hurst exponent. The dynamic plastic behavior at both room temperature and 200 °C exhibits a positive Lyapunov exponent, suggesting that the underlying dynamics is chaotic. The fractal dimension of the indentation depth increases with the increase of temperature, and there is an inflection at the holding time of 10 s at the same temperature. A large fractal dimension suggests the concurrent nucleation of a large number of slip bands. In particular, for the indentation with the holding time of 10 s at room temperature, the slip process evolves as a self-similar random process with a weak negative correlation similar to a random walk.

Agricultural Machinery - Equipment. Agricultural Cooperative Training. Vocational Agricluture. Revised.

ERIC Educational Resources Information Center

Sandlin, David, Comp.; And Others

Designed for students enrolled in the Agricultural Cooperative Part-Time Training Program, this course of study contains 12 units on agricultural machinery mechanics. Units include (examples of unit topics in parentheses): introduction (agricultural mechanics as an occupation; safety--shop and equipment; use of holding devices, jacks, lifts, and…

Slavic and Italian Canadian Attitudes towards Authority.

ERIC Educational Resources Information Center

Ryan, Michael G.

Predicting that Italian Canadians would hold attitudes of greater hostility and anxiety toward authority than Slavic Canadians, this study, using 58 part-time summer students (29 Italians and 29 Slavs) at three universities in Canada, analyzed the subjects' responses to the five-response option Likert type scale. Results confirmed the early…

Morphological changes in the cellulose and lignin components of biomass occur at different stages of steam pretreatment

DOE PAGES

Pingali, Sai Venkatesh; O'Neill, Hugh Michael; Nishiyama, Yoshiharu; ...

2014-01-09

Morphological changes to the different components of lignocellulosic biomass were observed as they occurred during steam pretreatment by placing a pressure reaction cell in a neutron beam and collecting time-resolved neutron scattering data. Changes to cellulose morphology occurred mainly in the heating phase, whereas changes in lignin morphology occurred mainly in the holding and cooling phases. During the heating stage, water is irreversibly expelled from cellulose microfibrils as the elementary fibrils coalesce. During the holding phase lignin aggregates begin to appear and they increase in size most noticeably during the cooling phase. This experiment demonstrates the unique information that inmore » situ small angle neutron scattering studies of pretreatment can provide. This approach is potentially useful in optimizing the heating, holding and cooling stages of pretreatments to allow the exact size and nature of lignin aggregates to be controlled in order to enhance enzyme accessibility to cellulose and therefore the efficiency of biomass conversion.« less

Effects of ageing on orofacial fine force control and its relationship with parallel change in sensory perception.

PubMed

Etter, Nicole M; Mckeon, Patrick O; Dressler, Emily V; Andreatta, Richard D

2017-05-03

Current theoretical models suggest the importance of a bidirectional relationship between sensation and production in the vocal tract to maintain lifelong speech skills. The purpose of this study was to assess age-related changes in orofacial skilled force production and to begin defining the orofacial perception-action relationship in healthy adults. Low-level orofacial force control measures (reaction time, rise time, peak force, mean hold force (N) and force hold SD) were collected from 60 adults (19-84 years). Non-parametric Kruskal Wallis tests were performed to identify statistical differences between force and group demographics. Non-parametric Spearman's rank correlations were completed to compare force measures against previously published sensory data from the same cohort of participants. Significant group differences in force control were found for age, sex, speech usage and smoking status. Significant correlational relationships were identified between labial vibrotactile thresholds and several low-level force control measures collected during step and ramp-and-hold conditions. These findings demonstrate age-related alterations in orofacial force production. Furthermore, correlational analysis suggests as vibrotactile detection thresholds increase, the ability to maintain low-level force control accuracy decreases. Possible clinical applications and treatment consequences of these findings for speech disorders in the ageing population are provided.

Modified inverse micelle synthesis for mesoporous alumina with a high D4 siloxane adsorption capacity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhong, Wei; Jiang, Ting; Jafari, Tahereh

In this work, mesoporous aluminas (MAs) with uniform and monomodal pores were fabricated via a modified inverse micelle synthesis method, using a non-polar solvent (to minimize the effect of water content) and short reaction time (for a fast evaporation process). The effects of reaction times (4–8 h), surfactant chain lengths (non-ionic surfactants), and calcination temperatures and hold times (450–600 °C; 1–4 h) on the textural properties of MA were studied. Additionally, the targeted pore sizes of MA were obtained in the range of 3.1–5.4 nm by adjusting the surfactant and reaction time. The surface area and pore volume were controlledmore » by the calcination temperature and hold time while maintaining the thermal stability of the materials. The tuned MA of the large mesopore volume achieved 168 mg/g octamethylcyclotetrasiloxane (D4 siloxane) adsorption capacity, a 32% improvement compared to commercially activated alumina. Finally, after three adsorption recycles, the synthesized MA still maintained approximate 85% of its original adsorption capacity, demonstrating a sustainable adsorption performance and high potential for related industrial applications.« less

Modified inverse micelle synthesis for mesoporous alumina with a high D4 siloxane adsorption capacity

DOE PAGES

Zhong, Wei; Jiang, Ting; Jafari, Tahereh; ...

2016-10-18

In this work, mesoporous aluminas (MAs) with uniform and monomodal pores were fabricated via a modified inverse micelle synthesis method, using a non-polar solvent (to minimize the effect of water content) and short reaction time (for a fast evaporation process). The effects of reaction times (4–8 h), surfactant chain lengths (non-ionic surfactants), and calcination temperatures and hold times (450–600 °C; 1–4 h) on the textural properties of MA were studied. Additionally, the targeted pore sizes of MA were obtained in the range of 3.1–5.4 nm by adjusting the surfactant and reaction time. The surface area and pore volume were controlledmore » by the calcination temperature and hold time while maintaining the thermal stability of the materials. The tuned MA of the large mesopore volume achieved 168 mg/g octamethylcyclotetrasiloxane (D4 siloxane) adsorption capacity, a 32% improvement compared to commercially activated alumina. Finally, after three adsorption recycles, the synthesized MA still maintained approximate 85% of its original adsorption capacity, demonstrating a sustainable adsorption performance and high potential for related industrial applications.« less

The association between workers' employability and burnout in a reorganization context: longitudinal evidence building upon the conservation of resources theory.

PubMed

De Cuyper, Nele; Raeder, Sabine; Van der Heijden, Beatrice I J M; Wittekind, Anette

2012-04-01

This longitudinal study probes the relationship between employability and burnout among employees from a company undergoing reorganization. We advanced employability as a personal resource that relates negatively to burnout. We expected that this hypothesis would hold for different operationalizations of employability, including (1) job-related and (2) transferable skills, (3) willingness to change jobs and (4) to develop competences, (5) opportunity awareness, (6) self-esteem, and (7) self-perceived employability (i.e., perceived employment opportunities). In a similar vein, we expected that the hypothesis would hold for the different dimensions of burnout; namely emotional exhaustion, depersonalization, and reduced personal accomplishment. We used longitudinal Hierarchical Linear Modeling (HLM) to test our hypotheses. Employees from a Swiss company undergoing a major reorganization were surveyed at three times with a total time lag of 19 months (Time 1: N = 287; Time 2: N = 128; Time 3: N = 107). Our results indicate that particularly self-esteem, but also job-related and transferable skills as indicators of one's employability were important predictors of burnout, with all relationships being negative. PsycINFO Database Record (c) 2012 APA, all rights reserved.

Growth hormone secretion during space flight and evaluation of the physiological responses of animals held in the research animal holding facility

NASA Technical Reports Server (NTRS)

Fast, Thomas N.; Grindeland, Richard; Mehler, William; Oyama, Jiro

1987-01-01

The spaceflight of the Research Animal Holding Facility (RAHF) on the Space Laboratory 3 (SL 3) provided the opportunity to evaluate the suitability of the RAHF for housing and maintaining experimental animals during spaceflight, and to determine changes in the secretion of growth hormone during spaceflight. Using ground-based studies the following were investigated: the optimum conditions for creating gravitational force on space flight animals; neural pathways that may play a role in the space flight syndrome; and the time course of muscle atrophy due to hypodynamia and hypokenesia in hindlimb-suspended animals and the role of growth hormone in these processes.

Space logistics simulation: Launch-on-time

NASA Technical Reports Server (NTRS)

Nii, Kendall M.

1990-01-01

During 1989-1990 the Center for Space Construction developed the Launch-On-Time (L-O-T) Model to help asses and improve the likelihood of successfully supporting space construction requiring multi-logistic delivery flights. The model chose a reference by which the L-O-T probability and improvements to L-O-T probability can be judged. The measure of improvement was chosen as the percent reduction in E(S(sub N)), the total expected amount of unscheduled 'hold' time. We have also previously developed an approach to determining the reduction in E(S(sub N)) by reducing some of the causes of unscheduled holds and increasing the speed at which the problems causing the holds may be 'fixed.' We provided a mathematical (binary linear programming) model for measuring the percent reduction in E(S(sub N)) given such improvements. In this presentation we shall exercise the model which was developed and draw some conclusions about the following: methods used, data available and needed, and make suggestions for areas of improvement in 'real world' application of the model.

The effect of hold-times on the fatigue behavior of type AISI 316L stainless steel under deuteron irradiation

NASA Astrophysics Data System (ADS)

Scholz, R.; Mueller, R.

1998-10-01

Strain controlled fatigue tests have been performed in torsion at 400°C on type 316L stainless steel samples in both 20% cold worked and annealed conditions during an irradiation with 19 MeV deuterons. A hold-time was imposed in the loading cycle. For the cold worked (cw) material, at shear strain ranges of 1.13% and 1.3%, irradiation creep induced stress relaxation led to the built up of a mean stress. The fatigue life was significantly reduced in comparison to thermal control tests. For the annealed (ann) material, tested under similar experimental conditions, irradiation creep effects were negligibly small compared to cyclic and irradiation hardening. The fatigue life was only slightly reduced. Continuous cycling tests conducted under irradiation conditions lay in the scatter band of the thermal control tests. The difference in fatigue life between continuous cycling and hold-time tests is attributed mainly to the observed difference in irradiation hardening.

[Development and succession of artificial biological soil crusts and water holding characteristics of topsoil].

PubMed

Wu, Li; Chen, Xiao-Guo; Zhang, Gao-Ke; Lan, Shu-Bin; Zhang, De-Lu; Hu, Chun-Xiang

2014-03-01

In order to understand the improving effects of cyanobacterial inoculation on water retention of topsoil in desert regions, this work focused on the development and succession of biological soil crusts and water holding characteristics of topsoil after cyanobacterial inoculation in Qubqi Desert. The results showed that after the artificial inoculation of desert cyanobacteria, algal crusts were quickly formed, and in some microenvironments direct succession of the algal crusts to moss crusts occurred after 2-3 years. With the development and succession of biological soil crusts, the topsoil biomass, polysaccharides content, crust thickness and porosity increased, while the soil bulk density decreased. At the same time, with crust development and succession, the topsoil texture became finer and the percents of fine soil particles including silt and clay contents increased, while the percents of coarse soil particles (sand content) decreased proportionately. In addition, it was found that with crust development and succession, the water holding capacity and water content of topsoil showed an increasing trend, namely: moss crust > algal crusts > shifting sand. The water content (or water holding capacity) in algal and moss crusts were 1.1-1.3 and 1.8-2.2 times of those in shifting sand, respectively. Correlation analysis showed that the water holding capacity and water content of topsoil were positively correlated with the crust biomass, polysaccharides content, thickness, bulk density, silt and clay content; while negatively correlated with the porosity and sand content. Furthermore, stepwise regression analysis showed that the main factor affecting water content was the clay content, while that affecting water holding capacity was the porosity.

On the Role of Processing Parameters in Producing Recycled Aluminum AA6061 Based Metal Matrix Composite (MMC-AlR) Prepared Using Hot Press Forging (HPF) Process

PubMed Central

Ahmad, Azlan; Lajis, Mohd Amri

2017-01-01

Solid-state recycling, which involves the direct recycling of scrap metal into bulk material using severe plastic deformation, has emerged as a potential alternative to the conventional remelting and recycling techniques. Hot press forging has been identified as a sustainable direct recycling technique that has fewer steps and maintains excellent material performance. An experimental investigation was conducted to explore the hardness and density of a recycled aluminum-based metal matrix composite by varying operating temperature and holding time. A mixture of recycled aluminum, AA6061, and aluminum oxide were simultaneously heated to 430, 480, and 530 °C and forged for 60, 90, and 120 min. We found a positive increase in microhardness and density for all composites. The hardness increased approximately 33.85%, while density improved by about 15.25% whenever the temperature or the holding time were increased. Based on qualitative analysis, the composite endures substantial plastic deformation due to the presence of hardness properties due to the aluminum oxide embedded in the aluminum matrix. These increases were significantly affected by the operating temperature; the holding time also had a subordinate role in enhancing the metal matrix composite properties. Furthermore, in an effort to curb the shortage of primary resources, this study reviewed the promising performance of secondary resources produced by using recycled aluminum and aluminum oxide as the base matrix and reinforcement constituent, respectively. This study is an outline for machining practitioners and the manufacturing industry to help increase industry sustainability with the aim of preserving the Earth for our community in the future. PMID:28925963

On the Role of Processing Parameters in Producing Recycled Aluminum AA6061 Based Metal Matrix Composite (MMC-AlR) Prepared Using Hot Press Forging (HPF) Process.

PubMed

Ahmad, Azlan; Lajis, Mohd Amri; Yusuf, Nur Kamilah

2017-09-19

Solid-state recycling, which involves the direct recycling of scrap metal into bulk material using severe plastic deformation, has emerged as a potential alternative to the conventional remelting and recycling techniques. Hot press forging has been identified as a sustainable direct recycling technique that has fewer steps and maintains excellent material performance. An experimental investigation was conducted to explore the hardness and density of a recycled aluminum-based metal matrix composite by varying operating temperature and holding time. A mixture of recycled aluminum, AA6061, and aluminum oxide were simultaneously heated to 430, 480, and 530 °C and forged for 60, 90, and 120 min. We found a positive increase in microhardness and density for all composites. The hardness increased approximately 33.85%, while density improved by about 15.25% whenever the temperature or the holding time were increased. Based on qualitative analysis, the composite endures substantial plastic deformation due to the presence of hardness properties due to the aluminum oxide embedded in the aluminum matrix. These increases were significantly affected by the operating temperature; the holding time also had a subordinate role in enhancing the metal matrix composite properties. Furthermore, in an effort to curb the shortage of primary resources, this study reviewed the promising performance of secondary resources produced by using recycled aluminum and aluminum oxide as the base matrix and reinforcement constituent, respectively. This study is an outline for machining practitioners and the manufacturing industry to help increase industry sustainability with the aim of preserving the Earth for our community in the future.

Development of sacrificial support fixture using deflection analysis

NASA Astrophysics Data System (ADS)

Ramteke, Ashwini M.; Ashtankar, Kishor M.

2018-04-01

Sacrificial support fixtures are the structures used to hold the part during machining while rotating the part about the fourth axis of CNC machining. In Four axis CNC machining part is held in a indexer which is rotated about the fourth axis of rotation. So using traditional fixturing devices to hold the part during machining such as jigs, v blocks and clamping plates needs a several set ups, manufacturing time which increase the cost associated with it. Since the part is rotated about the axis of rotation in four axis CNC machining so using traditional fixturing devices to hold the part while machining we need to reorient the fixture each time for particular orientation of part about the axis of rotation. So our proposed methodology of fixture design eliminates the cost associate with the complicated fixture design for customized parts which in turn reduces the time of manufacturing of the fixtures. But while designing the layout of the fixtures it is found out that the machining the part using four axis CNC machining the accurate machining of the part is directly proportional to the deflection produced in a part. So to machine an accurate part the deflection produced in a part should be minimum. We assume that the deflection produced in a part is a result of the deflection produced in a sacrificial support fixture while machining. So this paper provides the study of the deflection checking in a part machined using sacrificial support fixture by using FEA analysis.

An fMRI Study of Risky Decision Making: The Role of Mental Preparation and Conflict.

PubMed

Sohrabi, Ahmad; Smith, Andra M; West, Robert L; Cameron, Ian

2015-10-01

The current study aimed to elucidate the role of preparatory cognitive control in decision making and its neural correlates using functional Magnetic Resonance Imaging (fMRI). To this effect, by employing a series of new cognitive tasks, we assessed the role of preparatory cognitive control in monetary (risky) decision making. The participants had to decide between a risky and a safe gamble based on their chance of winning (high or low). In the 2-phase gambling task (similar to Cambridge gambling task), the chance and the gamble were presented at the same time (i.e. in a single phase), but in a new 3-phase gambling task, the chance is presented before the gamble. The tasks ended with a feedback phase. In the 3-phase task, holding the chance in memory to guide their decision enabled the participants to have more control on their risk taking behaviors as shown by activation in a network of brain areas involved in the control and conflict, including dorsal Anterior Cingulate Cortex (dACC), indexed by faster reaction times and better performance in the gambling task, and the temporal lobe, which has a role in holding contextual information. Holding information in memory to guide decision presumably enables the participants to have more control on their risk taking behaviors. The conflict and uncertainty resulting from this risky decision was indexed by the activation of dACC, known to be activated in conflict and cognitive control.

Determination of Career Planning Profiles of Turkish Athletes Who Are Ranked in the Olympics

ERIC Educational Resources Information Center

Hulya, Bingol; Cemal, Gundogdu; Sukru, Bingol

2012-01-01

This study researched in the level of career planning of Turkish athletes ranked in the Olympics during the time they were active in sports and after they retired. This study which aimed to determine the career planning efficiency of Turkish athletes ranked in the Olympics based on the viewpoints of the athletes holding Olympic degree is scanning…

Titration of Limited Hold to Comparison in Conditional Discrimination Training and Stimulus Equivalence Testing

ERIC Educational Resources Information Center

Arntzen, Erik; Haugland, Silje

2012-01-01

Reaction time (RT), thought to be important for acquiring a full understanding of the establishment of equivalence classes, has been reported in a number of studies within the area of stimulus equivalence research. In this study, we trained 3 classes of potentially 3 members, with arbitrary stimuli in a one-to-many training structure in 5 adult…

Holding equine oocytes in a commercial embryo-holding medium: New perspective on holding temperature and maturation time.

PubMed

Dini, Pouya; Bogado Pascottini, Osvaldo; Ducheyne, Kaatje; Hostens, Miel; Daels, Peter

2016-09-15

In the present study, we examined the effect of holding equine oocytes in Syngro embryo holding medium (EHM) overnight at either 4 °C, 17 °C, or 22 °C to 25 °C, on the time to maturation and developmental competence. We also examined the effect of placing denuded oocyte without extruded polar body back in maturation condition on subsequent maturation rate. In experiment 1, cumulus-oocyte complexes (COCs) were recovered postmortem and placed in EHM at 22 °C to 25 °C for 18 to 20 hours (OH) or placed directly in maturation (DM). The maturation rate was assessed after 22, 24, or 28 hours of culture. After denuding cumulus cells at 22 or 24 hours, oocytes without obvious polar body were placed back into culture and reassessed at subsequent time points. At 22 hours, a higher proportion of oocytes placed in OH achieved nuclear maturation than those placed in DM (63% and 37%, respectively, P = 0.008). At 24 and 28 hours, no significant differences in the % MII stage oocytes were observed between OH and DM. The nuclear maturation rate for OH oocytes was similar at 22, 24, and 28 hours, indicating that the maximum maturation rate was reached at an earlier time than that in DM. Oocytes fertilized by intracytoplasmic sperm injection resulted in a 7.1% and 6.3% blastocyst rate for OH and DM, respectively. Denuding oocytes after 22 hours or more of culture did not have an adverse effect on the final nuclear maturation rate. After 28 hours of culture, the same nuclear maturation rate (MII) was reached for nondenuded oocytes and oocytes denuded after 22 hours of 24 hours of culture. In experiment 2, COCs were held overnight at room temperature in EHM, then placed in maturation for 20, 22, and 28 hours. Nuclear maturation rate was significantly lower at 20 hours than 22 and 28 hours of culture and was similar at 22 and 28 hours, suggesting that at least 22 hours of culture is required to reach maximal maturation rate for stored oocytes (43%, 62%, and 65% at 20, 22, and 28 hours, respectively. P < 0.001). In experiment 3, COCs were either placed directly in culture or held at 22 °C to 25 °C, 17 °C, or 4 °C overnight. After 24 hours of culture, maturation rate was similar for all groups, suggesting that COCs can be stored in conventional 4 °C transport condition or 17 °C. In preliminary studies, COCs were held at 4 °C followed by 24 hours of culture, and mature oocytes were fertilized using intracytoplasmic sperm injection. Twenty-three injected oocytes yielded four blastocysts. In conclusion, we reported that oocytes can be placed in a commercial EHM and stored overnight without a detrimental effect on maturation rates or blastocyst development. Oocytes held in holding medium require less time to reach the MII stage than oocytes placed in culture directly. Removing the cumulus cells from oocytes that have been cultured for at least 22 hours does not seem to alter the final nuclear maturation rate. Finally, we observed no detrimental effect of storing oocytes at 4 °C for up to 18 hours, and oocytes appeared to maintain developmental competence and blastocyst potential. Copyright © 2016 Elsevier Inc. All rights reserved.

A new method for measuring lung deposition efficiency of airborne nanoparticles in a single breath

PubMed Central

Jakobsson, Jonas K. F.; Hedlund, Johan; Kumlin, John; Wollmer, Per; Löndahl, Jakob

2016-01-01

Assessment of respiratory tract deposition of nanoparticles is a key link to understanding their health impacts. An instrument was developed to measure respiratory tract deposition of nanoparticles in a single breath. Monodisperse nanoparticles are generated, inhaled and sampled from a determined volumetric lung depth after a controlled residence time in the lung. The instrument was characterized for sensitivity to inter-subject variability, particle size (22, 50, 75 and 100 nm) and breath-holding time (3–20 s) in a group of seven healthy subjects. The measured particle recovery had an inter-subject variability 26–50 times larger than the measurement uncertainty and the results for various particle sizes and breath-holding times were in accordance with the theory for Brownian diffusion and values calculated from the Multiple-Path Particle Dosimetry model. The recovery was found to be determined by residence time and particle size, while respiratory flow-rate had minor importance in the studied range 1–10 L/s. The instrument will be used to investigate deposition of nanoparticles in patients with respiratory disease. The fast and precise measurement allows for both diagnostic applications, where the disease may be identified based on particle recovery, and for studies with controlled delivery of aerosol-based nanomedicine to specific regions of the lungs. PMID:27819335

Effects of surgically implanted transmitters on reproduction and survival in mallards

USGS Publications Warehouse

Sheppard, Jennifer; Arnold, Todd W.; Amundson, Courtney L.; Klee, David

2017-01-01

Abdominally implanted radiotransmitters have been widely used in studies of waterbird ecology; however, the longer handling times and invasiveness of surgical implantation raise important concerns about animal welfare and potential effects on data quality. Although it is difficult to assess effects of handling and marking wild animals by comparing them with unmarked controls, insights can often be obtained by evaluating variation in handling or marking techniques. Here, we used data from 243 female mallards (Anas platyrhynchos) and mallard–grey duck hybrids (A. platyrhynchos × A. superciliosa) equipped with fully encapsulated abdominally implanted radiotransmitters from 2 study sites in New Zealand during 2014–2015 to assess potential marking effects. We evaluated survival, dispersal, and reproductive effort (e.g., breeding propensity, nest initiation date, clutch size) in response to 3 different attributes of handling duration and procedures: 1) processing time, including presurgery banding, measurements, and blood sampling of unanaesthetized birds; 2) surgery time from initiation to cessation of anesthetic; and 3) total holding time from first capture until release. We found no evidence that female survival, dispersal probability, or reproductive effort were negatively affected by holding, processing, or surgery time and concluded that we collected reliable data without compromising animal welfare. Our results support previous research that techniques using fully encapsulated abdominal-implant radiotransmitters are suitable to enable researchers to obtain reliable estimates of reproductive performance and survival. 

SPECT-CT Comparison of Lung Deposition using a System combining a Vibrating-mesh Nebulizer with a Valved Holding Chamber and a Conventional Jet Nebulizer: a Randomized Cross-over Study.

PubMed

Dugernier, Jonathan; Hesse, Michel; Vanbever, Rita; Depoortere, Virginie; Roeseler, Jean; Michotte, Jean-Bernard; Laterre, Pierre-François; Jamar, François; Reychler, Gregory

2017-02-01

To compare in vivo the total and regional pulmonary deposition of aerosol particles generated by a new system combining a vibrating-mesh nebulizer with a specific valved holding chamber and constant-output jet nebulizer connected to a corrugated tube. Cross-over study comparing aerosol delivery to the lungs using two nebulizers in 6 healthy male subjects: a vibrating-mesh nebulizer combined with a valved holding chamber (Aerogen Ultra®, Aerogen Ltd., Galway, Ireland) and a jet nebulizer connected to a corrugated tube (Opti-Mist Plus Nebulizer®, ConvaTec, Bridgewater, NJ). Nebulizers were filled with diethylenetriaminepentaacetic acid labelled with technetium-99 m ( 99m Tc-DTPA, 2 mCi/4 mL). Pulmonary deposition of 99m Tc-DTPA was measured by single-photon emission computed tomography combined with a low dose CT-scan (SPECT-CT). Pulmonary aerosol deposition from SPECT-CT analysis was six times increased with the vibrating-mesh nebulizer as compared to the jet nebulizer (34.1 ± 6.0% versus 5.2 ± 1.1%, p < 0.001). However, aerosol penetration expressed as the three-dimensional normalized ratio of the outer and the inner regions of the lungs was similar between both nebulizers. This study demonstrated the high superiority of the new system combining a vibrating-mesh nebulizer with a valved holding chamber to deliver nebulized particles into the lungs as comparted to a constant-output jet nebulizer with a corrugated tube.

Evidence for impulsivity in the Spontaneously Hypertensive Rat drawn from complementary response-withholding tasks

PubMed Central

Sanabria, Federico; Killeen, Peter R

2008-01-01

Background The inability to inhibit reinforced responses is a defining feature of ADHD associated with impulsivity. The Spontaneously Hypertensive Rat (SHR) has been extolled as an animal model of ADHD, but there is no clear experimental evidence of inhibition deficits in SHR. Attempts to demonstrate these deficits may have suffered from methodological and analytical limitations. Methods We provide a rationale for using two complementary response-withholding tasks to doubly dissociate impulsivity from motivational and motor processes. In the lever-holding task (LHT), continual lever depression was required for a minimum interval. Under a differential reinforcement of low rates schedule (DRL), a minimum interval was required between lever presses. Both tasks were studied using SHR and two normotensive control strains, Wistar-Kyoto (WKY) and Long Evans (LE), over an overlapping range of intervals (1 – 5 s for LHT and 5 – 60 s for DRL). Lever-holding and DRL performance was characterized as the output of a mixture of two processes, timing and iterative random responding; we call this account of response inhibition the Temporal Regulation (TR) model. In the context of TR, impulsivity was defined as a bias toward premature termination of the timed intervals. Results The TR model provided an accurate description of LHT and DRL performance. On the basis of TR parameter estimates, SHRs were more impulsive than LE rats across tasks and target times. WKY rats produced substantially shorter timed responses in the lever-holding task than in DRL, suggesting a motivational or motor deficit. The precision of timing by SHR, as measured by the variance of their timed intervals, was excellent, flouting expectations from ADHD research. Conclusion This research validates the TR model of response inhibition and supports SHR as an animal model of ADHD-related impulsivity. It indicates, however, that SHR's impulse-control deficit is not caused by imprecise timing. The use of ad hoc impulsivity metrics and of WKY as control strain for SHR impulsivity are called into question. PMID:18261220

Cardiogenic mixing increases aerosol deposition in the human lung in the absence of gravity.

PubMed

Prisk, G Kim; Sá, Rui Carlos; Darquenne, Chantal

2013-11-01

Exposure to extraterrestrial dusts is an almost inevitable consequence of any proposed planetary exploration. Previous studies in humans showed reduced deposition in low-gravity compared with normal gravity (1G). However, the reduced sedimentation means that fewer particles deposit in the airways, increasing the number of particles transported to the lung periphery where they eventually deposit albeit at a smaller rate than in 1G. In this study, we determined the role that gravity and other mechanisms such as cardiogenic mixing play in peripheral lung deposition during breath holds. Eight healthy subjects inhaled boluses of 0.5 μm-diameter particles to penetration volumes (V p ) of 300 and 1200ml that were followed by breath holds of up to 10 sec. Tests were performed in 1G and during short periods of microgravity (μG) aboard the NASA Microgravity Research Aircraft. Aerosol deposition and dispersion were calculated from these data. Results show that, for both V p , deposition in 1G was significantly higher than in μG. In contrast, while dispersion was significantly higher in 1G compared to μG at V p =1200ml, there was no significant gravitational effect on dispersion at V p =300ml. Finally, for each G level and V p , deposition and dispersion significantly increased with increasing breath-hold time. The most important finding of this study is that, even in the absence of gravity, aerosol deposition in the lung periphery increased with increasing residence time. Because the particles used in this study were too large to be significantly affected by Brownian diffusion, the increase in deposition is likely due to cardiogenic motion effects.

76 FR 20760 - Self-Regulatory Organizations; The NASDAQ Stock Market LLC; Notice of Designation of Longer Time...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-13

... Additional Criteria for Listing Commodity Stockpiling Companies That Have Indicated That Their Business Plan...'') that have indicated that their business plan is to buy and hold commodities. The proposed rule change..., standards for listing securities of companies whose business plan is to buy and hold commodities. \\9\\ The...

76 FR 68642 - Fisheries of the Northeastern United States; Atlantic Mackerel, Squid, and Butterfish Fisheries...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-07

...: Copies of supporting documents used by the Mid-Atlantic Fishery Management Council (Council), including..., Tier 1 and Tier 2 vessel owners are required to obtain a fish hold capacity measurement from a certified marine surveyor. The hold capacity measurement submitted at the time of application for a Tier 1...

Sociopolitical Oppression, Trauma, and Healing: Moving toward a Social Justice Art Therapy Framework

ERIC Educational Resources Information Center

Karcher, Owen Paul

2017-01-01

Art therapists hold a unique position to facilitate healing during a time of intense sociopolitical trauma. The current U.S. political climate is causing harm to marginalized groups, which necessitates an intentional exploration of how art therapists hold and wield power and privilege and how this can affect client outcomes. In this article, I…

Medicaid Bed-Hold Policies and Hospitalization of Long-Stay Nursing Home Residents

PubMed Central

Unruh, Mark Aaron; Grabowski, David C; Trivedi, Amal N; Mor, Vincent

2013-01-01

Objective To evaluate the effect of Medicaid bed-hold policies on hospitalization of long-stay nursing home residents. Data Sources A nationwide random sample of long-stay nursing home residents with data elements from Medicare claims and enrollment files, the Minimum Data Set, the Online Survey Certification and Reporting System, and Area Resource File. The sample consisted of 22,200,089 person-quarters from 754,592 individuals who became long-stay residents in 17,149 nursing homes over the period beginning January 1, 2000 through December 31, 2005. Study Design Linear regression models using a pre/post design adjusted for resident, nursing home, market, and state characteristics. Nursing home and year-quarter fixed effects were included to control for time-invariant facility influences and temporal trends associated with hospitalization of long-stay residents. Principal Findings Adoption of a Medicaid bed-hold policy was associated with an absolute increase of 0.493 percentage points (95% CI: 0.039–0.946) in hospitalizations of long-stay nursing home residents, representing a 3.883 percent relative increase over the baseline mean. Conclusions Medicaid bed-hold policies may increase the likelihood of hospitalization of long-stay nursing home residents and increase costs for the federal Medicare program. PMID:23521571

Quantitative analysis of hepatic fat fraction by single-breath-holding MR spectroscopy with T₂ correction: phantom and clinical study with histologic assessment.

PubMed

Hayashi, Norio; Miyati, Tosiaki; Minami, Takashi; Takeshita, Yumie; Ryu, Yasuji; Matsuda, Tsuyoshi; Ohno, Naoki; Hamaguchi, Takashi; Kato, Kenichiro; Takamura, Toshinari; Matsui, Osamu

2013-01-01

The focus of this study was on the investigation of the accuracy of the fat fraction of the liver by use of single-breath-holding magnetic resonance spectroscopy (MRS) with T (2) correction. Single-voxel proton MRS was performed with several TE values, and the fat fraction was determined with and without T (2) correction. MRS was also performed with use of the point-resolved spectroscopy sequence in single breath holding. The T (2) values of both water and fat were determined separately at the same time, and the effect of T (2) on the fat fraction was corrected. In addition, MRS-based fat fractions were compared with the degree of hepatic steatosis (HS) by liver biopsy in human subjects. With T (2) correction, the MRI-derived fat fractions were in good agreement with the fat fractions in all phantoms, but the fat fractions were overestimated without T (2) correction. R (2) values were in good agreement with the preset iron concentrations in the phantoms. The MRI-derived fat fraction was well correlated with the degree of HS. Iron deposited in the liver affects the signal strength when proton MRS is used for detection of the fat signal in the liver. However, the fat signal can be evaluated more accurately when the T (2) correction is applied. Breath-holding MRS minimizes the respiratory motion, and it can be more accurate in the quantification of the hepatic fat fraction.

Qualitative assessment of contrast-enhanced magnetic resonance angiography using breath-hold and non-breath-hold techniques in the portal venous system

NASA Astrophysics Data System (ADS)

Goo, Eun-Hoe; Kim, Sun-Ju; Dong, Kyung-Rae; Kim, Kwang-Choul; Chung, Woon-Kwan

2016-09-01

The purpose of this study is to evaluate the image quality in delineation of the portal venous systems with two different methods, breath-hold and non-breath-hold by using the 3D FLASH sequence. We used a 1.5 T system to obtain magnetic resonance(MR)images. Arterial and portal phase 3D FLASH images were obtained with breath-hold after a bolus injection of GD-DOTA. The detection of PVS on the MR angiograms was classified into three grades. First, the angiograms of the breath-hold method showed well the portal vein, the splenic vein and the superior mesenteric vein systems in 13 of 15 patients (86%) and the inferior mesenteric vein system in 6 of 15 patients (40%), Second, MR angiograms of the non-breath-hold method demonstrated the PVS and the SMV in 12 of 15 patients (80%) and the IMV in 5 of 15 patients (33%). Our study showed contrast-enhanced 3D FLASH MR angiography, together with the breath-hold technique, may provide reliable and accurate information on the portal venous system.

State Laws on Emergency Holds for Mental Health Stabilization.

PubMed

Hedman, Leslie C; Petrila, John; Fisher, William H; Swanson, Jeffrey W; Dingman, Deirdre A; Burris, Scott

2016-05-01

Psychiatric emergency hold laws permit involuntary admission to a health care facility of a person with an acute mental illness under certain circumstances. This study documented critical variation in state laws, identified important questions for evaluation research, and created a data set of laws to facilitate the public health law research of emergency hold laws' impact on mental health outcomes. The research team built a 50-state, open-source data set of laws currently governing emergency holds. A protocol and codebook were developed so that the study may be replicated and extended longitudinally, allowing future research to accurately capture changes to current laws. Although every state and the District of Columbia have emergency hold laws, state law varies on the duration of emergency holds, who can initiate an emergency hold, the extent of judicial oversight, and the rights of patients during the hold. The core criterion justifying an involuntary hold is mental illness that results in danger to self or others, but many states have added further specifications. Only 22 states require some form of judicial review of the emergency hold process, and only nine require a judge to certify the commitment before a person is hospitalized. Five states do not guarantee assessment by a qualified mental health professional during the emergency hold. The article highlights variability in state law for emergency holds of persons with acute mental illness. How this variability affects the individual, the treatment system, and law enforcement behavior is unknown. Research is needed to guide policy making and implementation on these issues.

Evaluation of Escherichia coli O157:H7 growth media for use in test-and-hold procedures for ground beef processing.

PubMed

Guerini, Michael N; Arthur, Terrance M; Shackelford, Steven D; Koohmaraie, Mohammad

2006-05-01

Since the mid-1990s, the beef industry has used a process called test and hold, wherein beef trim and ground beef are tested to keep products contaminated with Escherichia coli O157:H7 out of commerce. Current O157:H7 detection methods rely on a threshold level of bacterial growth for detection, which is dependent on the growth medium used. Twelve media were examined for growth and doubling time: buffered peptone water (BPW), SOC (which contains tryptone, yeast extract, KCl, MgCl2, and glucose), buffered peptone water plus SOC (BPW-SOC), Bacto-NZYM, RapidChek E. coli O157:H7 medium, BioControl EHEC8 culture medium, Neogen Reveal for E. coli O157:H7--Eight Hour medium (Neogen Reveal 8), BAX System medium for E. coli O157:H7 (BAX) BAX System medium for E. coli O157:H7 MP (BAX-MP), modified E. coli broth, nutrient medium, and tryptic soy broth (TSB). All media were tested at 37 or 42 degrees C under static or shaking conditions. The eight media with the highest total CFU per milliliter and most rapid doubling times were BPW-SOC, NZYM, RapidChek, EHEC8, Neogen Reveal 8, BAX, BAX-MP, and TSB. The ability of these eight media to enrich E. coli O157:H7 in ground beef was further evaluated through time-course experiments using immunomagnetic separation. Of these media, TSB was the easiest to prepare, had a wide application base, and was the least expensive. In the test-and-hold process, the normal ratio of medium to product is 1:10. In this study, a 1:3 ratio worked as well as a 1:10 ratio. Processors using test-and-hold procedures could use 1 liter of TSB to enrich for E. coli O157:H7 in a 375-g sample instead of the usual 3.375 liters, thus saving reagents, time, and labor while maintaining accuracy.

Interfacial Microstructure and Mechanical Strength of 93W/Ta Diffusion-Bonded Joints with Ni Interlayer

NASA Astrophysics Data System (ADS)

Luo, Guoqiang; Zhang, Jian; Li, Meijuan; Wei, Qinqin; Shen, Qiang; Zhang, Lianmeng

2013-02-01

93W alloy and Ta metal were successfully diffusion bonded using a Ni interlayer. Ni4W was found at the W-Ni interface, and Ni3Ta and Ni2Ta were formed at the Ni-Ta interface. The shear strength of the joints increases with increasing holding time, reaching a value of 202 MPa for a joint prepared using a 90-minute holding time at 1103 K (830 °C) and 20 MPa. The fracture of this joint occurred within the Ni/Ta interface.

Children's Experiences of Time when a Parent Travels for Work.

PubMed

Zvonkovic, Anisa; Swenson, Andrea; Cornwell, Zoë

2017-08-01

This qualitative study focuses on different ways time is experienced by children in families who face time challenges due to a family member's job that required work travel. Data are from a family-level study that includes interviews of all family members over the age of 7. Using grounded theory methodology, this study illustrates ways in which job demands and family processes interact. Analysis centers on the 75 children's perspectives from 43 families. Holding together assessments of having enough time while wanting more time with their parents, children express emotion, generally unrecognized by parents, around the topic of family time. Children's experience of time with parents is rushed or calm, depending on the activities done in time and the gender of the parent with whom they spend time. Findings are interpreted through a feminist social constructionist lens.

Strongly correlated fermions after a quantum quench.

PubMed

Manmana, S R; Wessel, S; Noack, R M; Muramatsu, A

2007-05-25

Using the adaptive time-dependent density-matrix renormalization group method, we study the time evolution of strongly correlated spinless fermions on a one-dimensional lattice after a sudden change of the interaction strength. For certain parameter values, two different initial states (e.g., metallic and insulating) lead to observables which become indistinguishable after relaxation. We find that the resulting quasistationary state is nonthermal. This result holds for both integrable and nonintegrable variants of the system.

Two Echelon Supply Chain Integrated Inventory Model for Similar Products: A Case Study

NASA Astrophysics Data System (ADS)

Parjane, Manoj Baburao; Dabade, Balaji Marutirao; Gulve, Milind Bhaskar

2017-06-01

The purpose of this paper is to develop a mathematical model towards minimization of total cost across echelons in a multi-product supply chain environment. The scenario under consideration is a two-echelon supply chain system with one manufacturer, one retailer and M products. The retailer faces independent Poisson demand for each product. The retailer and the manufacturer are closely coupled in the sense that the information about any depletion in the inventory of a product at a retailer's end is immediately available to the manufacturer. Further, stock-out is backordered at the retailer's end. Thus the costs incurred at the retailer's end are the holding costs and the backorder costs. The manufacturer has only one processor which is time shared among the M products. Production changeover from one product to another entails a fixed setup cost and a fixed set up time. Each unit of a product has a production time. Considering the cost components, and assuming transportation time and cost to be negligible, the objective of the study is to minimize the expected total cost considering both the manufacturer and retailer. In the process two aspects are to be defined. Firstly, every time a product is taken up for production, how much of it (production batch size, q) should be produced. Considering a large value of q favors the manufacturer while a small value of q suits the retailers. Secondly, for a given batch size q, at what level of retailer's inventory (production queuing point), the batch size S of a product be taken up for production by the manufacturer. A higher value of S incurs more holding cost whereas a lower value of S increases the chance of backorder. A tradeoff between the holding and backorder cost must be taken into consideration while choosing an optimal value of S. It may be noted that due to multiple products and single processor, a product `taken' up for production may not get the processor immediately, and may have to wait in a queue. The `S' should factor in the probability of waiting time in the queue.

Evaluation of Different Dose-Response Models for High Hydrostatic Pressure Inactivation of Microorganisms

PubMed Central

2017-01-01

Modeling of microbial inactivation by high hydrostatic pressure (HHP) requires a plot of the log microbial count or survival ratio versus time data under a constant pressure and temperature. However, at low pressure and temperature values, very long holding times are needed to obtain measurable inactivation. Since the time has a significant effect on the cost of HHP processing it may be reasonable to fix the time at an appropriate value and quantify the inactivation with respect to pressure. Such a plot is called dose-response curve and it may be more beneficial than the traditional inactivation modeling since short holding times with different pressure values can be selected and used for the modeling of HHP inactivation. For this purpose, 49 dose-response curves (with at least 4 log10 reduction and ≥5 data points including the atmospheric pressure value (P = 0.1 MPa), and with holding time ≤10 min) for HHP inactivation of microorganisms obtained from published studies were fitted with four different models, namely the Discrete model, Shoulder model, Fermi equation, and Weibull model, and the pressure value needed for 5 log10 (P5) inactivation was calculated for all the models above. The Shoulder model and Fermi equation produced exactly the same parameter and P5 values, while the Discrete model produced similar or sometimes the exact same parameter values as the Fermi equation. The Weibull model produced the worst fit (had the lowest adjusted determination coefficient (R2adj) and highest mean square error (MSE) values), while the Fermi equation had the best fit (the highest R2adj and lowest MSE values). Parameters of the models and also P5 values of each model can be useful for the further experimental design of HHP processing and also for the comparison of the pressure resistance of different microorganisms. Further experiments can be done to verify the P5 values at given conditions. The procedure given in this study can also be extended for enzyme inactivation by HHP. PMID:28880255

Emotional Valence and Physical Space: Limits of Interaction

ERIC Educational Resources Information Center

de la Vega, Irmgard; de Filippis, Monica; Lachmair, Martin; Dudschig, Carolin; Kaup, Barbara

2012-01-01

According to the body-specificity hypothesis, people associate positive things with the side of space that corresponds to their dominant hand and negative things with the side corresponding to their nondominant hand. Our aim was to find out whether this association holds also true for a response time study using linguistic stimuli, and whether…

Binge Drinking and Risky Sex among College Students. NBER Working Paper No. 15953

ERIC Educational Resources Information Center

DeSimone, Jeffrey S.

2010-01-01

This study examines the relationship between binge drinking and sexual behavior in nationally representative data on age 18-24 four-year college students. For having sex, overall or without condoms, large and significant positive associations are eliminated upon holding constant proxies for time-invariant sexual activity and drinking preferences.…

Pairing Script and Dialogue: Combinations that Show Promise for Second or Foreign Language Learning.

ERIC Educational Resources Information Center

Holobow, N. E.; And Others

1984-01-01

Describes a study to determine if the initial advantage of listening to first language dialogs while reading second language scripts (i.e., reversed subtitling) would hold up over time and if a combination of coordinated dialogs and scripts both in the second language would gain effectiveness through usage. (SED)

Physical quality of Simental Ongole crossbred silverside meat at various boiling times

NASA Astrophysics Data System (ADS)

Riyanto, J.; Cahyadi, M.; Guntari, W. S.

2018-03-01

This study aims to determine the physical quality of silverside beef meat at various boiling times. Samples that have been used are the back thigh or silverside meat. Treatment of boiling meat included TR (meat without boiled), R15 (boiled 15 minutes), and R30 (boiled for 30 minutes). The experimental design using Completely Randomized Design with 3 replications. Each replication was done in triple physical quality test. Determination of physical quality was performed at the Livestock Industry and Processing Laboratory at Sebelas Maret University Surakarta and the Meat Technology Laboratory at the Faculty of Animal Husbandry of Gadjah Mada University. The result of variance analysis showed that boiling affect cooking loss (P≥0.05) and but did not affect (P≤0,05) pH, water holding capacity and meat tenderness. The conclusions of the study showed that boiling for 15 minutes and 30 minutes decreased the cooking loss of Simental Ongole Crossbred silverside meat. Meat physical quality of pH, water holding capacity and the value of tenderness is not affected by boiling for 15 and 30 minutes.

Experimental Evaluation of Preservation Techniques for Benzene, Toluene, Ethylbenzene, and Total Xylenes in Water Samples.

PubMed

Arnold, Ray; Kong, Deyuan; Douglas, Gregory; Hardenstine, Jeffery; Rouhani, Shahrokh; Gala, William

2018-01-01

An experiment was designed to address the validity of the prescribed maximum allowable holding-time limit of 14 days when acidified at < 2 pH and maintained at 4°C to prevent significant loss of benzene, toluene, ethyl benzene, and xylenes (BTEX) in preserved water samples. Preservation methods prescribed by the United State Environmental Protection Agency were used as well as adaptions of that procedure to determine stability between 3 and 21 days. Water samples preserved at 4°C and pH of < 2 with hydrochloric acid did not result in unacceptable (> 15%) BTEX losses during the study as defined by procedures and statistical methods described by the American Society for Testing and Materials International. In addition, water samples preserved only with acid (pH < 2) at ambient temperatures (20-27°C) also provided acceptable results during the 21-day study. These results have demonstrated the acceptability of BTEX data derived from water samples exceeding the standard holding-time and/or temperature limits.

The Effects of Borides on the Mechanical Properties of TLPB Repaired Inconel 738 Superalloy

NASA Astrophysics Data System (ADS)

Wei, J.; Ye, Y.; Sun, Z.; Zou, G.; Bai, H.; Wu, A.; Liu, L.

2017-10-01

The transient liquid phase diffusion bonding (TLPB) method was used to repair an artificial crack in Inconel 738, which was notched by a femtosecond laser. Mixed ratios of BNi-1a:DF-4B were investigated at the bonding temperature of 1373 K (1100 °C) for 2 to 36 hours. The effect of borides on the mechanical properties of TLPB repaired joints was studied through analysis of the microstructure, fracture path, and morphology observations. The borides formation, morphology, distribution, and joints strength were studied in detail. The results showed that the diffusion of B can either increase or decrease the joint strength, depending on its distribution and morphology. The amount of large blocky Ni-B compounds in the precipitate zone were reduced with increasing holding time, which resulted in an increase in joint strength. Nevertheless, further increasing the holding time led to a decrease in joint strength because of the formation of continuous acicular borides in the diffusion-affected zone. The fracture modes of TLPB joints were also discussed on the basis of the microstructure and fractography.

Effect of Creep and Oxidation on Reduced Creep-Fatigue life of Ni-based Alloy 617 at 850 C

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Xiang; Yang, Zhiqing; Sokolov, Mikhail A

Low cycle fatigue (LCF) and creep fatigue testing of Ni-based alloy 617 was carried out at 850 C. Compared with its LCF life, the material s creep fatigue life decreases to different extents depending on test conditions. To elucidate the microstructure-fatigue property relationship for alloy 617 and the effect of creep and oxidation on its fatigue life, systematic microstructural investigations were carried out using scanning electron microscopy, energy-dispersive X-ray spectroscopy, and electron backscatter diffraction (EBSD). In LCF tests, as the total strain range increased, deformations concentrated near high angle grain boundaries (HAGBs). The strain hold period in the creep fatiguemore » tests introduced additional creep damage to the material, which revealed the detrimental effect of the strain hold time on the material fatigue life in two ways. First, the strain hold time enhanced the localized deformation near HAGBs, resulting in the promotion of intergranular cracking of alloy 617. Second, the strain hold time encouraged grain boundary sliding, which resulted in interior intergranular cracking of the material. Oxidation accelerated the initiation of intergranular cracking in alloy 617. In the crack propagation stage, if oxidation was promoted and the cyclic oxidation damage was greater than the fatigue damage, oxidation-assisted intergranular crack growth resulted in a significant reduction in the material s fatigue life.« less

Impact of holding and equilibration time on post-thaw quality of shipped boar semen.

PubMed

Schäfer, J; Waberski, D; Jung, M; Schulze, M

2017-12-01

Cryopreservation of boar semen is of growing interest for breeding companies. Overnight-shipping of pre-diluted ejaculates to specialized laboratories offers a practicable method, but requires fine-tuned protocols. In this study, the impact of holding post shipping at 17°C for 2 or 24h (n=10 samples) and of equilibration in lactose-egg yolk extender without glycerol at 5°C for 2, 4, 24 or 48h (n=11 samples) before freezing was investigated. Sperm-rich fractions of ejaculates from 21 mature Pietrain boars were collected at a single boar stud. After pre-dilution (1+1, v:v) with Beltsville thawing solution, samples were sent to the laboratory. Temperature profiles during transport and initial equilibration time were recorded. Semen quality post-thaw (PT) was evaluated using CASA and flow cytometry. Holding of 2h after shipping resulted in higher sperm motility (P=0.013) and beat cross frequency (BCF; P=0.047) compared to 24h. Differences between both groups vanished with prolonged incubation at 38°C PT. Equilibration at 5°C for 4h yielded the highest motility and BCF, whereas the equilibration for 48h impaired sperm motility. Membrane integrity, mitochondrial activity and DNA fragmentation index were not affected by any protocol modification. In conclusion, processing of pre-diluted boar semen shipped overnight within 2h after arrival at the laboratory is preferred to 24h of additional holding at 17°C. Extending the equilibration period in lactose-egg yolk extender without glycerol at 5°C from 2h to 4h before freezing is recommended. Copyright © 2017 Elsevier B.V. All rights reserved.

Effect of Annealing on Microstructures and Hardening of Helium-Hydrogen-Implanted Sequentially Vanadium Alloys

NASA Astrophysics Data System (ADS)

Jiang, Shaoning; Wang, Zhiming

2018-03-01

The effect of post-irradiation annealing on the microstructures and mechanical properties of V-4Cr-4Ti alloys was studied. Helium-hydrogen-irradiated sequentially V-4Cr-4Ti alloys at room temperature (RT) were undergone post-irradiation annealing at 450 °C over periods of up to 30 h. These samples were carried out by high-resolution transmission electron microscopy (HRTEM) observation and nanoindentation test. With the holding time, large amounts of point defects produced during irradiation at RT accumulated into large dislocation loops and then dislocation nets which promoted the irradiation hardening. Meanwhile, bubbles appeared. As annealing time extended, these bubbles grew up and merged, and finally broke up. In the process, the size of bubbles increased and the number density decreased. Microstructural changes due to post-irradiation annealing corresponded to the change of hardening. Dislocations and bubbles are co-contributed to irradiation hardening. With the holding time up to 30 h, the recovery of hardening is not obvious. The phenomenon was discussed by dispersed barrier hardening model and Friedel-Kroupa-Hirsch relationship.

Changes in cassava toxicity during processing into gari and ijapu--two fermented food products.

PubMed

Sokari, T G; Karibo, P S

1992-01-01

Grated cassava to which tap water was added at levels of 25%, 50% and 75% (v/w) was held at 30 degrees C, 40 degrees C or 50 degrees C and examined over a 6 h period for cyanide content, pH and titratable acidity (TTA). During the come-up time, i.e. the time between addition of water and attainment of desired holding temperature (between 14 and 47 min), reductions in bound cyanide of ca 54-85% occurred, depending on the level of added water and holding temperature. The corresponding losses for the control samples, to which no water was added, were ca 25-33%. The biggest reduction in the bound cyanide of > 99% (from 89.0 to 0.6 ppm) occurred in grated cassava with 75% added water held at 50 degrees C. There was little or no change in pH during the period of study. The reduction of processing time for certain cassava products based on separation into detoxication and flavour development/fermentation stages is discussed.

Gaze-evoked nystagmus induced by alcohol intoxication.

PubMed

Romano, Fausto; Tarnutzer, Alexander A; Straumann, Dominik; Ramat, Stefano; Bertolini, Giovanni

2017-03-15

The cerebellum is the core structure controlling gaze stability. Chronic cerebellar diseases and acute alcohol intoxication affect cerebellar function, inducing, among others, gaze instability as gaze-evoked nystagmus. Gaze-evoked nystagmus is characterized by increased centripetal eye-drift. It is used as an important diagnostic sign for patients with cerebellar degeneration and to assess the 'driving while intoxicated' condition. We quantified the effect of alcohol on gaze-holding using an approach allowing, for the first time, the comparison of deficits induced by alcohol intoxication and cerebellar degeneration. Our results showed that alcohol intoxication induces a two-fold increase of centripetal eye-drift. We establish analysis techniques for using controlled alcohol intake as a model to support the study of cerebellar deficits. The observed similarity between the effect of alcohol and the clinical signs observed in cerebellar patients suggests a possible pathomechanism for gaze-holding deficits. Gaze-evoked nystagmus (GEN) is an ocular-motor finding commonly observed in cerebellar disease, characterized by increased centripetal eye-drift with centrifugal correcting saccades at eccentric gaze. With cerebellar degeneration being a rare and clinically heterogeneous disease, data from patients are limited. We hypothesized that a transient inhibition of cerebellar function by defined amounts of alcohol may provide a suitable model to study gaze-holding deficits in cerebellar disease. We recorded gaze-holding at varying horizontal eye positions in 15 healthy participants before and 30 min after alcohol intake required to reach 0.6‰ blood alcohol content (BAC). Changes in ocular-motor behaviour were quantified measuring eye-drift velocity as a continuous function of gaze eccentricity over a large range (±40 deg) of horizontal gaze angles and characterized using a two-parameter tangent model. The effect of alcohol on gaze stability was assessed analysing: (1) overall effects on the gaze-holding system, (2) specific effects on each eye and (3) differences between gaze angles in the temporal and nasal hemifields. For all subjects, alcohol consumption induced gaze instability, causing a two-fold increase [2.21 (0.55), median (median absolute deviation); P = 0.002] of eye-drift velocity at all eccentricities. Results were confirmed analysing each eye and hemifield independently. The alcohol-induced transient global deficit in gaze-holding matched the pattern previously described in patients with late-onset cerebellar degeneration. Controlled intake of alcohol seems a suitable disease model to study cerebellar GEN. With alcohol resulting in global cerebellar hypofunction, we hypothesize that patients matching the gaze-holding behaviour observed here suffered from diffuse deficits in the gaze-holding system as well. © 2016 The Authors. The Journal of Physiology © 2016 The Physiological Society.

The impact of green roof ageing on substrate characteristics and hydrological performance

NASA Astrophysics Data System (ADS)

De-Ville, Simon; Menon, Manoj; Jia, Xiaodong; Reed, George; Stovin, Virginia

2017-04-01

Green roofs contribute to stormwater management through the retention of rainfall and the detention of runoff. However, there is very limited knowledge concerning the evolution of green roof hydrological performance with system age. This study presents a non-invasive technique which allows for repeatable determination of key substrate characteristics over time, and evaluates the impact of observed substrate changes on hydrological performance. The physical properties of 12 green roof substrate cores have been evaluated using non-invasive X-ray microtomography (XMT) imaging. The cores comprised three replicates of two contrasting substrate types at two different ages: unused virgin samples; and 5-year-old samples from existing green roof test beds. Whilst significant structural differences (density, pore and particle sizes, tortuosity) between virgin and aged samples of a crushed brick substrate were observed, these differences did not significantly affect hydrological characteristics (maximum water holding capacity and saturated hydraulic conductivity). A contrasting substrate based upon a light expanded clay aggregate experienced increases in the number of fine particles and pores over time, which led to increases in maximum water holding capacity of 7%. In both substrates, the saturated hydraulic conductivity estimated from the XMT images was lower in aged compared with virgin samples. Comparisons between physically-derived and XMT-derived substrate hydrological properties showed that similar values and trends in the data were identified, confirming the suitability of the non-invasive XMT technique for monitoring changes in engineered substrates over time. The observed effects of ageing on hydrological performance were modelled as two distinct hydrological processes, retention and detention. Retention performance was determined via a moisture-flux model using physically-derived values of virgin and aged maximum water holding capacity. Increased water holding capacity with age increases the potential for retention performance. However, seasonal variations in retention performance greatly exceed those associated with the observed age-related increases in water holding capacity (+72% vs +7% respectively). Detention performance was determined via an unsaturated-flow finite element model, using van Genuchten parameters and XMT-derived values of saturated hydraulic conductivity. Reduced saturated hydraulic conductivity increases detention performance. For a 1-hour 30-year design storm, the peak runoff was found to be 33% lower for the aged brick-based substrate compared with its virgin counterpart.

The effect of friction in the hold down post spherical bearings on hold down post loads

NASA Technical Reports Server (NTRS)

Richardson, James A.

1990-01-01

The effect of friction at the connection of the Solid Rocket Booster (SRB) aft skirt and the mobile launch platform (MLP) hold down posts was analyzed. A simplified model of the shuttle response during the Space Shuttle Main Engine (SSME) buildup was constructed. The model included the effect of stick-slip friction for the rotation of the skirt about the spherical bearing. Current finite element models assume the joint is completely frictionless in rotation and therefore no moment is transferred between the skirt and the hold down posts. The model was partially verified against test data and preliminary parameter studies were performed. The parameter studies indicated that the coefficient of friction strongly influenced the moment on the hold down posts. The coefficient of friction had little effect on hold down post vertical loads, however. Further calibration of the model is necessary before the effect of friction on the hold down post horizontal loads can be analyzed.

Creep-Fatigue Behavior of Alloy 617 at 850 and 950°C, Revision 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carroll, L.; Carroll, M.

Alloy 617 is the leading candidate material for an Intermediate Heat Exchanger (IHX) of the Very High Temperature Reactor (VHTR). To evaluate the behavior of this material in the expected service conditions, strain-controlled cyclic tests including hold times up to 9000 s at maximum tensile strain were conducted at 850 and 950 degrees C. At both temperatures, the fatigue resistance decreased when a hold time was added at peak tensile strain. The magnitude of this effect depended on the specific mechanisms and whether they resulted in a change in fracture mode from transgranular in pure fatigue to intergranular in creep-fatiguemore » for a particular temperature and strain range combination. Increases in the tensile hold duration beyond an initial value were not detrimental to the creep-fatigue resistance at 950 degrees C but did continue to degrade the lifetimes at 850 degrees C.« less

Normalized coffin-manson plot in terms of a new life function based on stress relaxation under creep-fatigue conditions

NASA Astrophysics Data System (ADS)

Jeong, Chang Yeol; Nam, Soo Woo; Lim, Jong Dae

2003-04-01

A new life prediction function based on a model formulated in terms of stress relaxation during hold time under creep-fatigue conditions is proposed. From the idea that reduction in fatigue life with hold is due to the creep effect of stress relaxation that results in additional energy dissipation in the hysteresis loop, it is suggested that the relaxed stress range may be a creep-fatigue damage function. Creep-fatigue data from the present and other investigators are used to check the validity of the proposed life prediction equation. It is shown that the data satisfy the applicability of the life relation model. Accordingly, using this life prediction model, one may realize that all the Coffin-Manson plots at various levels of hold time in strain-controlled creep-fatigue tests can be normalized to make one straight line.

Optimization of Injection Molding Parameters for HDPE/TiO₂ Nanocomposites Fabrication with Multiple Performance Characteristics Using the Taguchi Method and Grey Relational Analysis.

PubMed

Pervez, Hifsa; Mozumder, Mohammad S; Mourad, Abdel-Hamid I

2016-08-22

The current study presents an investigation on the optimization of injection molding parameters of HDPE/TiO₂ nanocomposites using grey relational analysis with the Taguchi method. Four control factors, including filler concentration (i.e., TiO₂), barrel temperature, residence time and holding time, were chosen at three different levels of each. Mechanical properties, such as yield strength, Young's modulus and elongation, were selected as the performance targets. Nine experimental runs were carried out based on the Taguchi L₉ orthogonal array, and the data were processed according to the grey relational steps. The optimal process parameters were found based on the average responses of the grey relational grades, and the ideal operating conditions were found to be a filler concentration of 5 wt % TiO₂, a barrel temperature of 225 °C, a residence time of 30 min and a holding time of 20 s. Moreover, analysis of variance (ANOVA) has also been applied to identify the most significant factor, and the percentage of TiO₂ nanoparticles was found to have the most significant effect on the properties of the HDPE/TiO₂ nanocomposites fabricated through the injection molding process.

Orofacial and thumb-index finger ramp-and-hold isometric force dynamics in young neurotypical adults.

PubMed

Barlow, Steven M; Hozan, Mohsen; Lee, Jaehoon; Greenwood, Jake; Custead, Rebecca; Wardyn, Brianna; Tippin, Kaytlin

2018-04-27

The relation among several parameters of the ramp-and-hold isometric force contraction (peak force and dF/dt max during the initial phase of force recruitment, and the proportion of hold-phase at target) was quantified for the right and left thumb-index finger pinch, and lower lip midline compression in 40 neurotypical right-handed young adults (20 female/20 males) using wireless force sensors and data acquisition technology developed in our laboratory. In this visuomotor control task, participants produced ramp-and-hold isometric forces as 'rapidly and accurately' as possible to end-point target levels at 0.25, 0.5, 1 and 2 Newtons presented to a computer monitor in a randomized block design. Significant relations were found between the parameters of the ramp-and-hold lip force task and target force level, including the peak rate of force change (dF/dt max ), peak force, and the criterion percentage of force within ±5% of target during the contraction hold phase. A significant performance advantage was found among these force variables for the thumb-index finger over the lower lip. The maximum voluntary compression force (MVCF) task revealed highly significant differences in force output between the thumb-index fingers and lower lip (∼4.47-4.70 times greater for the digits versus lower lip), a significant advantage of the right thumb-index finger over the non-dominant left thumb-index finger (12% and 25% right hand advantage for males and females, respectively), and a significant sex difference (∼1.65-1.73 times greater among males). Copyright © 2018 Elsevier Ltd. All rights reserved.

The "Financial Counseling and Planning" Indexing Project: Establishing a Correlation between Indexing, Total Citations, and Library Holdings

ERIC Educational Resources Information Center

Kelsey, Paul J.

2007-01-01

The researcher hypothesized that increasing the number of indexing services covering a journal would increase library holdings and total citations for the journal. A sample group of 40 Journal Citation Reports (JCR) journals in the "Business, Finance" category was identified and checked for the number of times indexed in Ulrich's…

Gas-Bearing Crucible for Shot Tower

NASA Technical Reports Server (NTRS)

Youngberg, C. L.; Miller, C. G.; Stephens, J. B.; Finnerty, A. A.

1983-01-01

Device protects molten drops from contamination and distortion. Gas flowing through levitator tube levitates small balls while they melt. Gas heated by filament extending through center of tube. Gas bearing crucible on tube has concave configuration to hold single relatively large ball or many recesses to hold many small balls. By time spheres reach foam, they are cooled sufficiently by radiation to retain their shape.

Influence of holding temperature on the growth and survival of Salmonella spp. and Staphylococcus aureus and the production of staphylococcal enterotoxin in egg products.

PubMed

Yang, S E; Yu, R C; Chou, C C

2001-01-22

In this study, growth and survival of Salmonella spp. and Staphylococcus aureus in steamed egg and scrambled egg held at 5, 18, 22, 37, 55 and 60 degrees C are investigated. The production of staphylococcal enterotoxin in steamed egg is also examined. Results reveal that Salmonella spp. and Staph. aureus in the egg products multiply best at 37 degrees C, followed closely by 22 and 18 degrees C. Neither pathogen showed growth in the egg products held at 5 degrees C. Initial inoculation dose, holding temperature and holding time affected the population of both organisms found in the egg products. Staphylococcal enterotoxin A (SEA) and B (SEB) are detected only in the egg products held at 37 or 22 degrees C. After holding at 37 degrees C for 36 h, scrambled egg inoculated with ca. 5.0 log cfu/g Staph. aureus contains the highest levels of SEA (> 64 ng/g) and SEB (> 64 ng/g). Although Salmonella spp. and Staph. aureus grow better in steamed eggs than in scrambled eggs, production of staphylococcal enterotoxin, in general, was higher in scrambled eggs than in steamed eggs. On the other hand, a repaid destruction of the test organisms in steamed eggs held at 60 degrees C was observed. Holding the steamed eggs at 60 degrees C, Salmonella spp. and Staph. aureus with an initial population of ca. 5.9 and 5.6 log cfu/g, respectively, reduced to a non-detectable level in 1 h.

Series resonant converter with auxiliary winding turns: analysis, design and implementation

NASA Astrophysics Data System (ADS)

Lin, Bor-Ren

2018-05-01

Conventional series resonant converters have researched and applied for high-efficiency power units due to the benefit of its low switching losses. The main problems of series resonant converters are wide frequency variation and high circulating current. Thus, resonant converter is limited at narrow input voltage range and large input capacitor is normally adopted in commercial power units to provide the minimum hold-up time requirement when AC power is off. To overcome these problems, the resonant converter with auxiliary secondary windings are presented in this paper to achieve high voltage gain at low input voltage case such as hold-up time duration when utility power is off. Since the high voltage gain is used at low input voltage cased, the frequency variation of the proposed converter compared to the conventional resonant converter is reduced. Compared to conventional resonant converter, the hold-up time in the proposed converter is more than 40ms. The larger magnetising inductance of transformer is used to reduce the circulating current losses. Finally, a laboratory prototype is constructed and experiments are provided to verify the converter performance.

High temperature, low cycle fatigue of copper-base alloys in argon. Part 3: Zirconium-copper; thermal-mechanical strain cycling, hold-time and notch fatigue results

NASA Technical Reports Server (NTRS)

Conway, J. B.; Stentz, R. H.; Berling, J. T.

1973-01-01

The low-cycle fatigue characteristics of smooth bar and notched bar specimens (hourglass shape) of zirconium-copper, 1/2 Hard, material (R-2 Series) were evaluated at room temperature in axial strain control. Over the fatigue life range from about 300 to 3000 cycles the ratio of fatigue life for smooth bar to fatigue life for notched bar remained constant at a value of about 6.0. Some additional hold-time data for the R-2 alloy tested in argon at 538 C are reported. An analysis of the relaxation data obtained in these hold-time tests is also reported and it is shown that these data yield a fairly consistent correlation in terms of instantaneous stress rate divided by instantaneous stress. Two thermal-mechanical strain cycling tests were also performed using a cyclic frequency of 4.5 cycles per hour and a temperature cycling interval from 260 to 538 C. The fatigue life values in these tests were noticeably lower than that observed in isothermal tests at 538 C.

Anatomic and Pathologic Variability During Radiotherapy for a Hybrid Active Breath-Hold Gating Technique

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glide-Hurst, Carri K.; Gopan, Ellen; Department of Radiation Oncology Wayne State University, Detroit, MI

2010-07-01

Purpose: To evaluate intra- and interfraction variability of tumor and lung volume and position using a hybrid active breath-hold gating technique. Methods and Materials: A total of 159 repeat normal inspiration active breath-hold CTs were acquired weekly during radiotherapy for 9 lung cancer patients (12-21 scans per patient). A physician delineated the gross tumor volume (GTV), lungs, and spinal cord on the first breath-hold CT, and contours were propagated semiautomatically. Intra- and interfraction variability of tumor and lung position and volume were evaluated. Tumor centroid and border variability were quantified. Results: On average, intrafraction variability of lung and GTV centroidmore » position was <2.0 mm. Interfraction population variability was 3.6-6.7 mm (systematic) and 3.1-3.9 mm (random) for the GTV centroid and 1.0-3.3 mm (systematic) and 1.5-2.6 mm (random) for the lungs. Tumor volume regressed 44.6% {+-} 23.2%. Gross tumor volume border variability was patient specific and demonstrated anisotropic shape change in some subjects. Interfraction GTV positional variability was associated with tumor volume regression and contralateral lung volume (p < 0.05). Inter-breath-hold reproducibility was unaffected by time point in the treatment course (p > 0.1). Increases in free-breathing tidal volume were associated with increases in breath-hold ipsilateral lung volume (p < 0.05). Conclusions: The breath-hold technique was reproducible within 2 mm during each fraction. Interfraction variability of GTV position and shape was substantial because of tumor volume and breath-hold lung volume change during therapy. These results support the feasibility of a hybrid breath-hold gating technique and suggest that online image guidance would be beneficial.« less

Treatment of low strains and long hold times in high temperature metal fatigue by strainrange partitioning

NASA Technical Reports Server (NTRS)

Manson, S. S.; Zab, R.

1977-01-01

A procedure for treating creep-fatigue for low strainranges and long hold times is outlined. A semi-experimental approach, wherein several cycles of the imposed loading is actually applied to a specimen in order to determine the stable hysteresis loop, can be very useful in the analysis. Because such tests require only a small fraction of the total failure time, they are not inherently prohibitive if experimental equipment is available. The need for accurate constitutive equations is bypassed because the material itself acts to translate the imposed loading into the responsive hysteresis loops. When strainrange partitioning has been applied in such cases very good results have been obtained.

Pelvic floor muscle exercises utilizing trunk stabilization for treating postpartum urinary incontinence: randomized controlled pilot trial of supervised versus unsupervised training.

PubMed

Kim, Eun-Young; Kim, Suhn-Yeop; Oh, Duck-Won

2012-02-01

To investigate the effect of supervised and unsupervised pelvic floor muscle exercises utilizing trunk stabilization for treating postpartum urinary incontinence and to compare the outcomes. Randomized, single-blind controlled study. Outpatient rehabilitation hospital. Eighteen subjects with postpartum urinary incontinence. Subjects were randomized to either a supervised training group with verbal instruction from a physiotherapist, or an unsupervised training group after undergoing a supervised demonstration session. Bristol Female Lower Urinary Tract Symptom questionnaire (urinary symptoms and quality of life) and vaginal function test (maximal vaginal squeeze pressure and holding time) using a perineometer. The change values for urinary symptoms (-27.22 ± 6.20 versus -18.22 ± 5.49), quality of life (-5.33 ± 2.96 versus -1.78 ± 3.93), total score (-32.56 ± 8.17 versus -20.00 ± 6.67), maximal vaginal squeeze pressure (18.96 ± 9.08 versus 2.67 ± 3.64 mmHg), and holding time (11.32 ± 3.17 versus 5.72 ± 2.29 seconds) were more improved in the supervised group than in the unsupervised group (P < 0.05). In the supervised group, significant differences were found for all variables between pre- and post-test values (P < 0.01), whereas the unsupervised group showed significant differences for urinary symptom score, total score and holding time between the pre- and post-test results (P < 0.05). These findings suggest that exercising the pelvic floor muscles by utilizing trunk stabilization under physiotherapist supervision may be beneficial for the management of postpartum urinary incontinence.

Treatment of Chronic Breath-Holding in an Adult with Severe Mental Retardation: A Clinical Case Study

ERIC Educational Resources Information Center

Reed, Derek D.; Martens, Brian K.

2008-01-01

We describe a clinical case study surrounding the behavioral assessment and operant treatment of, an adult with severe mental retardation who engaged in chronic breath-holding. In this clinical case, previous neurological and medical testing had ruled out biological bases for the individual's breath-holding. A functional behavioral assessment…

On High-Order Radiation Boundary Conditions

NASA Technical Reports Server (NTRS)

Hagstrom, Thomas

1995-01-01

In this paper we develop the theory of high-order radiation boundary conditions for wave propagation problems. In particular, we study the convergence of sequences of time-local approximate conditions to the exact boundary condition, and subsequently estimate the error in the solutions obtained using these approximations. We show that for finite times the Pade approximants proposed by Engquist and Majda lead to exponential convergence if the solution is smooth, but that good long-time error estimates cannot hold for spatially local conditions. Applications in fluid dynamics are also discussed.

An EOQ model for weibull distribution deterioration with time-dependent cubic demand and backlogging

NASA Astrophysics Data System (ADS)

Santhi, G.; Karthikeyan, K.

2017-11-01

In this article we introduce an economic order quantity model with weibull deterioration and time dependent cubic demand rate where holding costs as a linear function of time. Shortages are allowed in the inventory system are partially and fully backlogging. The objective of this model is to minimize the total inventory cost by using the optimal order quantity and the cycle length. The proposed model is illustrated by numerical examples and the sensitivity analysis is performed to study the effect of changes in parameters on the optimum solutions.

Seal Formation Mechanism Beneath Animal Waste Holding Ponds

NASA Astrophysics Data System (ADS)

Cihan, A.; Tyner, J. S.; Wright, W. C.

2005-12-01

Infiltration of animal waste from holding ponds can cause contamination of groundwater. Typically, the initial flux from a pond decreases rapidly as a seal of animal waste particulates is deposited at the base of the pond. The purpose of this study was to investigate the mechanism of the seal formation. Twenty-four soil columns (10-cm diameter by 43-cm long) were hand-packed with sand, silty loam or clay soils. A 2.3 m column of dairy or swine waste was applied to the top of the each column. The leakage rate from each column was measured with respect to time to analyze the effect of seal formation on different soil textures and animal waste types. We tested our hypothesis that seal growth and the subsequent decrease of leachate production adheres to a filter cake growth model. Said model predicts that the cumulative leakage rate is proportional to the square root of time and to the square root of the height of the waste.

Blood hyperviscosity identification with reflective spectroscopy of tongue tip based on principal component analysis combining artificial neural network.

PubMed

Liu, Ming; Zhao, Jing; Lu, XiaoZuo; Li, Gang; Wu, Taixia; Zhang, LiFu

2018-05-10

With spectral methods, noninvasive determination of blood hyperviscosity in vivo is very potential and meaningful in clinical diagnosis. In this study, 67 male subjects (41 health, and 26 hyperviscosity according to blood sample analysis results) participate. Reflectance spectra of subjects' tongue tips is measured, and a classification method bases on principal component analysis combined with artificial neural network model is built to identify hyperviscosity. Hold-out and Leave-one-out methods are used to avoid significant bias and lessen overfitting problem, which are widely accepted in the model validation. To measure the performance of the classification, sensitivity, specificity, accuracy and F-measure are calculated, respectively. The accuracies with 100 times Hold-out method and 67 times Leave-one-out method are 88.05% and 97.01%, respectively. Experimental results indicate that the built classification model has certain practical value and proves the feasibility of using spectroscopy to identify hyperviscosity by noninvasive determination.

Study on the Inference Factors of Huangling Coking Coal Pyrolysis

NASA Astrophysics Data System (ADS)

Du, Meili; Yang, Zongyi; Fan, Jinwen

2018-01-01

In order to reasonably and efficiently utilize Huangling coking coal resource, coal particle, heating rate, holding time, pyrolysis temperature and others factors were dicussed for the influence of those factor on Huangling coking coal pyrolysis products. Several kinds of coal blending for coking experiments were carried out with different kinds of coal such as Huangling coking coal, Xida coal with high ash low sufur, Xinghuo fat coal with hign sulfur, Zhongxingyi coking coal with high sulfur, Hucun lean coal, mixed meager and lean coal. The results shown that the optimal coal particle size distribution was 0.5~1.5mm, the optimal heating rate was 8°C/min, the optimal holding time was 15min, the optimal pyrolysis temperature was 800°C for Huangling coking coal pyrolysis, the tar yield increased from 4.7% to 11.2%. The maximum tar yield of coal blending for coking under the best single factor experiment condition was 10.65% when the proportio of Huangling coking coal was 52%.

Effect of Spark-Plasma-Sintering Conditions on Tensile Properties of Aluminum Matrix Composites Reinforced with Multiwalled Carbon Nanotubes (MWCNTs)

NASA Astrophysics Data System (ADS)

Chen, B.; Imai, H.; Umeda, J.; Takahashi, M.; Kondoh, K.

2017-04-01

In this study, aluminum (Al) matrix composites containing 2 wt.% multiwalled carbon nanotubes (CNTs) were fabricated by powder metallurgy using high-energy ball milling (HEBM), spark plasma sintering (SPS), and subsequent hot extrusion. The effect of SPS conditions on the tensile properties of CNT/Al composites was investigated. The results showed that composites with well-dispersed CNTs and nearly full-density CNT/Al can be obtained. During HEBM, CNTs were shortened, inserted into welded Al powder particles, bonded to Al, and still stable without CNT-Al reaction. After consolidation, Al4C3 phases formed in composites under different sintering conditions. With the increase of sintering temperature and holding time, the strength decreased. Conversely, the ductility and toughness noticeably increased. As a result, a good balance between strength (367 MPa in ultimate tensile strength) and ductility (13% in elongation) was achieved in the as-extruded CNT/Al composite sintered at 630°C with a holding time of 300 min.

Observations related to the Salmonella EU layer baseline survey in the United Kingdom: follow-up of positive flocks and sensitivity issues.

PubMed

Carrique-Mas, J J; Breslin, M; Snow, L; Arnold, M E; Wales, A; McLaren, I; Davies, R H

2008-11-01

A follow-on study was carried out on 23 holdings identified as Salmonella positive in the 2004/2005 European Union (EU) baseline survey of Salmonella in laying hens. Eleven of 13 cage and 4/7 floor houses remained positive for Salmonella when the new flock was tested, and from 10/13 cage and 3/7 floor houses a Salmonella of the same serovar/phage type as found in the EU survey was isolated. There was a high correlation between the level of contamination in the houses at the time of the EU survey and in the follow-on flock. On seven occasions the house identified as positive in the EU survey was sampled after cleaning and disinfection but before a new flock was placed, and in all of them Salmonella could be isolated from the houses. The observed number of infected houses in infected holdings suggests that the holding-level prevalence in the United Kingdom would be about 21% higher than the results obtained in the EU survey.

Observations related to the Salmonella EU layer baseline survey in the United Kingdom: follow-up of positive flocks and sensitivity issues

PubMed Central

CARRIQUE-MAS, J. J.; BRESLIN, M.; SNOW, L.; ARNOLD, M. E.; WALES, A.; McLAREN, I.; DAVIES, R. H.

2008-01-01

SUMMARY A follow-on study was carried out on 23 holdings identified as Salmonella positive in the 2004/2005 European Union (EU) baseline survey of Salmonella in laying hens. Eleven of 13 cage and 4/7 floor houses remained positive for Salmonella when the new flock was tested, and from 10/13 cage and 3/7 floor houses a Salmonella of the same serovar/phage type as found in the EU survey was isolated. There was a high correlation between the level of contamination in the houses at the time of the EU survey and in the follow-on flock. On seven occasions the house identified as positive in the EU survey was sampled after cleaning and disinfection but before a new flock was placed, and in all of them Salmonella could be isolated from the houses. The observed number of infected houses in infected holdings suggests that the holding-level prevalence in the United Kingdom would be about 21% higher than the results obtained in the EU survey. PMID:18177519

Hormone-injected gravid channel catfish held in individual mesh bag reduces handling stress and improves reproductive performance in hatcheries

USDA-ARS?s Scientific Manuscript database

This study compared holding hormone-injected female channel catfish in soft-mesh bags to communally held hormone-injected female catfish in a tank as a stress reduction strategy to improve reproductive performance. Fish held in tanks were crowded, handled multiple times to record weight prior to ho...

Marriage and Retirement: Advice to Couples in Popular Literature.

ERIC Educational Resources Information Center

Harbert, Ellen M.; And Others

Though academic research has shown retirement to be viewed by retirees as a satisfying time in life, popular opinion holds that retirement is a difficult adjustment for a couple. This study was undertaken to find out more about one source of popular opinion, the popular press. All popular books and magazine articles on the topic of marriage and…

Comparison of the Efficiency of Two Flashcard Drill Methods on Children's Reading Performance

ERIC Educational Resources Information Center

Joseph, Laurice; Eveleigh, Elisha; Konrad, Moira; Neef, Nancy; Volpe, Robert

2012-01-01

The purpose of this study was to extend prior flashcard drill and practice research by holding instructional time constant and allowing learning trials to vary. Specifically, the authors aimed to determine whether an incremental rehearsal method or a traditional drill and practice method was most efficient in helping 5 first-grade children read,…

Don't Hold Back? the Effect of Grade Retention on Student Achievement

ERIC Educational Resources Information Center

Diris, Ron

2017-01-01

This study analyzes the effect of age-based retention on school achievement at different stages of education. I estimate an instrumental variable model, using the predicted probability of retention given month of birth as an instrument, while simultaneously accounting for the effect of month of birth on maturity at the time of testing. The…

Associations between Language and Problem Behavior: A Systematic Review and Correlational Meta-Analysis

ERIC Educational Resources Information Center

Chow, Jason C.; Wehby, Joseph H.

2018-01-01

A growing body of evidence points to the common co-occurrence of language and behavioral difficulties in children. Primary studies often focus on this relation in children with identified deficits. However, it is unknown whether this relation holds across other children at risk or representative samples of children or over time. The purpose of…

Mixing Business Communication and Business Statistics with Experiential Learning: Student and Instructor Reflections on Work-Related Undergraduate Business Research Projects

ERIC Educational Resources Information Center

Roach-Duncan, Joy

2010-01-01

In recent times experiential learning attempted to assist student development in almost every field. More specifically regarding business studies, instructors have used experiential learning projects in a variety of ways, depending upon the business function. The described learning project progression holds the potential to be useful to…

A Developmental Study Examining the Value, Effectiveness, and Quality of a Data Literacy Intervention

ERIC Educational Resources Information Center

Rogers, Michelle Antionette

2015-01-01

Previous research indicates that pre- and in-service teachers are not receiving adequate training to implement data-informed instructional decision making. This is problematic given the promise this decision making process holds for improving instruction and student learning. At the same time, many educators do not see the value of different types…

Weathering "A Climate of Unexpectation": Gender Equity and the Radcliffe Institute, 1960-1995.

ERIC Educational Resources Information Center

Eisenmann, Linda

1995-01-01

The evolution and role of the Radcliffe Institute for Independent Study, founded to provide year-long, part-time fellowships for women doctorates wishing to pursue independent scholarly or creative projects, are described. The program, which encourages applications from mothers whose intellectual work had been put on hold, is seen as one of the…

Cash Management in the United States Marine Corps.

DTIC Science & Technology

1984-12-01

procedures and requires that such departments and agencies conduct financial * activities in a manner that will make cash holding require- ments...balances so as to minimize the overall cost of holding cash" [Ref. 3: 2). Simply stated, effective cash management implies the minimization of cash...balances held, as opposed to invested , as well as timely receipt and disbursement of government funds. B. ORGANIZATION RESPONSIBILITY FOR FINANCIAL

Nonenhanced MR angiography of the pulmonary arteries using single-shot radial quiescent-interval slice-selective (QISS): a technical feasibility study.

PubMed

Edelman, Robert R; Silvers, Robert I; Thakrar, Kiran H; Metzl, Mark D; Nazari, Jose; Giri, Shivraman; Koktzoglou, Ioannis

2017-06-30

For evaluation of the pulmonary arteries in patients suspected of pulmonary embolism, CT angiography (CTA) is the first-line imaging test with contrast-enhanced MR angiography (CEMRA) a potential alternative. Disadvantages of CTA include exposure to ionizing radiation and an iodinated contrast agent, while CEMRA is sensitive to respiratory motion and requires a gadolinium-based contrast agent. The primary goal of our technical feasibility study was to evaluate pulmonary arterial conspicuity using breath-hold and free-breathing implementations of a recently-developed nonenhanced approach, single-shot radial quiescent-interval slice-selective (QISS) MRA. Breath-hold and free-breathing, navigator-gated versions of radial QISS MRA were evaluated at 1.5 Tesla in three healthy subjects and 11 patients without pulmonary embolism or arterial occlusion by CTA. Images were scored by three readers for conspicuity of the pulmonary arteries through the level of the segmental branches. In addition, one patient with pulmonary embolism was imaged. Scan time for a 54-slice acquisition spanning the pulmonary arteries was less than 2 minutes for breath-hold QISS, and less than 3.4 min using free-breathing QISS. Pulmonary artery branches through the segmental level were conspicuous with either approach. Free-breathing scans showed only mild blurring compared with breath-hold scans. For both readers, less than 1% of pulmonary arterial segments were rated as "not seen" for breath-hold and navigator-gated QISS, respectively. In subjects with atrial fibrillation, single-shot radial QISS consistently depicted the pulmonary artery branches, whereas navigator-gated 3D balanced steady-state free precession showed motion artifacts. In one patient with pulmonary embolism, radial QISS demonstrated central pulmonary emboli comparably to CEMRA and CTA. The thrombi were highly conspicuous on radial QISS images, but appeared subtle and were not prospectively identified on scout images acquired using a single-shot bSSFP acquisition. In this technical feasibility study, both breath-hold and free-breathing single-shot radial QISS MRA enabled rapid, consistent demonstration of the pulmonary arteries through the level of the segmental branches, with only minimal artifacts from respiratory motion and cardiac arrhythmias. Based on these promising initial results, further evaluation in patients with suspected pulmonary embolism appears warranted.

Macroindentation hardness measurement-Modernization and applications.

PubMed

Patel, Sarsvat; Sun, Changquan Calvin

2016-06-15

In this study, we first developed a modernized indentation technique for measuring tablet hardness. This technique is featured by rapid digital image capture, using a calibrated light microscope, and precise area-determination. We then systematically studied effects of key experimental parameters, including indentation force, speed, and holding time, on measured hardness of a very soft material, hydroxypropyl cellulose, and a very hard material, dibasic calcium phosphate, to cover a wide range of material properties. Based on the results, a holding period of 3min at the peak indentation load is recommended to minimize the effect of testing speed on H. Using this method, we show that an exponential decay function well describes the relationship between tablet hardness and porosity for seven commonly used pharmaceutical powders investigated in this work. We propose that H and H at zero porosity may be used to quantify the tablet deformability and powder plasticity, respectively. Copyright © 2016 Elsevier B.V. All rights reserved.

Predictive factors of excessive online poker playing.

PubMed

Hopley, Anthony A B; Nicki, Richard M

2010-08-01

Despite the widespread rise of online poker playing, there is a paucity of research examining potential predictors for excessive poker playing. The aim of this study was to build on recent research examining motives for Texas Hold'em play in students by determining whether predictors of other kinds of excessive gambling apply to Texas Hold'em. Impulsivity, negative mood states, dissociation, and boredom proneness have been linked to general problem gambling and may play a role in online poker. Participants of this study were self-selected online poker players (N = 179) who completed an online survey. Results revealed that participants played an average of 20 hours of online poker a week and approximately 9% of the sample was classified as a problem gambler according to the Canadian Problem Gambling Index. Problem gambling, in this sample, was uniquely predicted by time played, dissociation, boredom proneness, impulsivity, and negative affective states, namely depression, anxiety, and stress.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Conroy, L; Quirk, S; Smith, WL

Purpose: We used Real-Time Position Management (RPM) to evaluate breath hold amplitude and variability when gating with a visually monitored deep inspiration breath hold technique (VM-DIBH) with retrospective cine image chest wall position verification. Methods: Ten patients with left-sided breast cancer were treated using VM-DIBH. Respiratory motion was passively collected once weekly using RPM with the marker block positioned at the xiphoid process. Cine images on the tangent medial field were acquired on fractions with RPM monitoring for retrospective verification of chest wall position during breath hold. The amplitude and duration of all breath holds on which treatment beams weremore » delivered were extracted from the RPM traces. Breath hold position coverage was evaluated for symmetric RPM gating windows from ± 1 to 5 mm centered on the average breath hold amplitude of the first measured fraction as a baseline. Results: The average (range) breath hold amplitude and duration was 18 mm (3–36 mm) and 19 s (7–34 s). The average (range) of amplitude standard deviation per patient over all breath holds was 2.7 mm (1.2–5.7 mm). With the largest allowable RPM gating window (± 5 mm), 4 of 10 VM-DIBH patients would have had ≥ 10% of their breath hold positions excluded by RPM. Cine verification of the chest wall position during the medial tangent field showed that the chest wall was greater than 5 mm from the baseline in only 1 out of 4 excluded patients. Cine images verify the chest wall/breast position only, whether this variation is acceptable in terms of heart sparing is a subject of future investigation. Conclusion: VM-DIBH allows for greater breath hold amplitude variability than using a 5 mm gating window with RPM, while maintaining chest wall positioning accuracy within 5 mm for the majority of patients.« less

Common Cause Case Study: An Estimated Probability of Four Solid Rocket Booster Hold-down Post Stud Hang-ups

NASA Technical Reports Server (NTRS)

Cross, Robert

2005-01-01

Until Solid Rocket Motor ignition, the Space Shuttle is mated to the Mobil Launch Platform in part via eight (8) Solid Rocket Booster (SRB) hold-down bolts. The bolts are fractured using redundant pyrotechnics, and are designed to drop through a hold-down post on the Mobile Launch Platform before the Space Shuttle begins movement. The Space Shuttle program has experienced numerous failures where a bolt has "hung-up." That is, it did not clear the hold-down post before liftoff and was caught by the SRBs. This places an additional structural load on the vehicle that was not included in the original certification requirements. The Space Shuttle is currently being certified to withstand the loads induced by up to three (3) of eight (8) SRB hold-down post studs experiencing a "hang-up." The results af loads analyses performed for four (4) stud-hang ups indicate that the internal vehicle loads exceed current structural certification limits at several locations. To determine the risk to the vehicle from four (4) stud hang-ups, the likelihood of the scenario occurring must first be evaluated. Prior to the analysis discussed in this paper, the likelihood of occurrence had been estimated assuming that the stud hang-ups were completely independent events. That is, it was assumed that no common causes or factors existed between the individual stud hang-up events. A review of the data associated with the hang-up events, showed that a common factor (timing skew) was present. This paper summarizes a revised likelihood evaluation performed for the four (4) stud hang-ups case considering that there are common factors associated with the stud hang-ups. The results show that explicitly (i.e. not using standard common cause methodologies such as beta factor or Multiple Greek Letter modeling) taking into account the common factor of timing skew results in an increase in the estimated likelihood of four (4) stud hang-ups of an order of magnitude over the independent failure case.

Common Cause Case Study: An Estimated Probability of Four Solid Rocket Booster Hold-Down Post Stud Hang-ups

NASA Technical Reports Server (NTRS)

Cross, Robert

2005-01-01

Until Solid Rocket Motor ignition, the Space Shuttle is mated to the Mobil Launch Platform in part via eight (8) Solid Rocket Booster (SRB) hold-down bolts. The bolts are fractured using redundant pyrotechnics, and are designed to drop through a hold-down post on the Mobile Launch Platform before the Space Shuttle begins movement. The Space Shuttle program has experienced numerous failures where a bolt has hung up. That is, it did not clear the hold-down post before liftoff and was caught by the SRBs. This places an additional structural load on the vehicle that was not included in the original certification requirements. The Space Shuttle is currently being certified to withstand the loads induced by up to three (3) of eight (8) SRB hold-down experiencing a "hang-up". The results of loads analyses performed for (4) stud hang-ups indicate that the internal vehicle loads exceed current structural certification limits at several locations. To determine the risk to the vehicle from four (4) stud hang-ups, the likelihood of the scenario occurring must first be evaluated. Prior to the analysis discussed in this paper, the likelihood of occurrence had been estimated assuming that the stud hang-ups were completely independent events. That is, it was assumed that no common causes or factors existed between the individual stud hang-up events. A review of the data associated with the hang-up events, showed that a common factor (timing skew) was present. This paper summarizes a revised likelihood evaluation performed for the four (4) stud hang-ups case considering that there are common factors associated with the stud hang-ups. The results show that explicitly (i.e. not using standard common cause methodologies such as beta factor or Multiple Greek Letter modeling) taking into account the common factor of timing skew results in an increase in the estimated likelihood of four (4) stud hang-ups of an order of magnitude over the independent failure case.

Multiview 3-D Echocardiography Fusion with Breath-Hold Position Tracking Using an Optical Tracking System.

PubMed

Punithakumar, Kumaradevan; Hareendranathan, Abhilash R; McNulty, Alexander; Biamonte, Marina; He, Allen; Noga, Michelle; Boulanger, Pierre; Becher, Harald

2016-08-01

Recent advances in echocardiography allow real-time 3-D dynamic image acquisition of the heart. However, one of the major limitations of 3-D echocardiography is the limited field of view, which results in an acquisition insufficient to cover the whole geometry of the heart. This study proposes the novel approach of fusing multiple 3-D echocardiography images using an optical tracking system that incorporates breath-hold position tracking to infer that the heart remains at the same position during different acquisitions. In six healthy male volunteers, 18 pairs of apical/parasternal 3-D ultrasound data sets were acquired during a single breath-hold as well as in subsequent breath-holds. The proposed method yielded a field of view improvement of 35.4 ± 12.5%. To improve the quality of the fused image, a wavelet-based fusion algorithm was developed that computes pixelwise likelihood values for overlapping voxels from multiple image views. The proposed wavelet-based fusion approach yielded significant improvement in contrast (66.46 ± 21.68%), contrast-to-noise ratio (49.92 ± 28.71%), signal-to-noise ratio (57.59 ± 47.85%) and feature count (13.06 ± 7.44%) in comparison to individual views. Copyright © 2016 World Federation for Ultrasound in Medicine & Biology. Published by Elsevier Inc. All rights reserved.

Single-Breath-Hold Whole-heart Unenhanced Coronary MRA Using Multi-shot Gradient Echo EPI at 3T: Comparison with Free-breathing Turbo-field-echo Coronary MRA on Healthy Volunteers.

PubMed

Iyama, Yuji; Nakaura, Takeshi; Nagayama, Yasunori; Oda, Seitaro; Utsunomiya, Daisuke; Kidoh, Masafumi; Yuki, Hideaki; Hirata, Kenichiro; Namimoto, Tomohiro; Kitajima, Mika; Morita, Kosuke; Funama, Yoshinori; Takemura, Atsushi; Okuaki, Tomoyuki; Yamashita, Yasuyuki

2018-04-10

We investigated the feasibility of single breath hold unenhanced coronary MRA using multi-shot gradient echo planar imaging (MSG-EPI) on a 3T-scanner. Fourteen volunteers underwent single breath hold coronary MRA with a MSG-EPI and free-breathing turbo field echo (TFE) coronary MRA at 3T. The acquisition time, signal to noise ratio (SNR), and the contrast of the sequences were compared with the paired t-test. Readers evaluated the image contrast, noise, sharpness, artifacts, and the overall image quality. The acquisition time was 88.1% shorter for MSG-EPI than TFE (24.7 ± 2.5 vs 206.4 ± 23.1 sec, P < 0.01). The SNR was significantly higher on MSG-EPI than TFE scans (P < 0.01). There was no significant difference in the contrast on MSG-EPI and TFE scans (1.8 ± 0.3 vs 1.9 ± 0.3, P = 0.24). There was no significant difference in image contrast, image sharpness, and overall image quality between two scan techniques. The score of image noise and artifact were significantly higher on MSG-EPI than TFE scans (P < 0.05). The single breath hold MSG-EPI sequence is a promising technique for shortening the scan time and for preserving the image quality of unenhanced whole heart coronary MRA on a 3T scanner.

Impact of hyperventilation and apnea on myocardial oxygenation in patients with obstructive sleep apnea - An oxygenation-sensitive CMR study.

PubMed

Roubille, François; Fischer, Kady; Guensch, Dominik P; Tardif, Jean-Claude; Friedrich, Matthias G

2017-02-01

Oxygenation-sensitive cardiovascular magnetic resonance imaging (OS-CMR) is an emerging technique that can monitor changes in myocardial oxygenation in vivo. Obstructive sleep apnea syndrome (OSAS) is associated with endothelial and microcirculatory dysfunction and increased cardiovascular morbidity and mortality. Little is known about myocardial responses to apnea in patients with OSAS. We hypothesized that the coronary vascular response to hyperventilation and long breath-hold is diminished in patients with OSAS when compared to healthy volunteers. Twenty-nine OSAS patients and 36 healthy volunteers were prospectively enrolled. All CMR scans were performed on a clinical 3T system. Participants performed a breathing maneuver with 60s of hyperventilation followed by a maximal breath-hold. During the breath-hold, OS-CMR images were continuously acquired and signal intensity changes were measured by a blinded reader. Patients with OSAS were older than healthy volunteers (p<0.01) and presented more co-morbidities; 66% were currently treated with nocturnal positive airway pressure. Compared to healthy participants, the expected increase of myocardial oxygenation during the first 15s of the breath-hold was significantly lower in patients with OSAS (2.6±8.3% vs. 6.7±5.6%; p<0.05), and remained reduced at all time points during the breath-hold. Importantly this result was mainly driven by patients under continuous positive airway pressure (CPAP), suggesting that CPAP might have a greater impact on increase of myocardial oxygenation rather than OSAS itself. The myocardial vascular response to combined breathing maneuvers of hyperventilation followed by voluntary apnea is blunted in patients with obstructive sleep apnea. Clinical studies should now further define the clinical role of oxygenation-sensitive CMR in patients with respiratory disorders. Copyright © 2016 Japanese College of Cardiology. Published by Elsevier Ltd. All rights reserved.

Effect of Surgical Curve Correction on Exercise Tolerance and Physical Capacities in Patients of Severe Spinal Deformity.

PubMed

Patil, Prateek C; Rathod, Ashok K; Borde, Mandar; Singh, Vishwajeet; Singh, Hemant U

2016-12-01

Traditionally, surgical intervention for patients with a spinal deformity has been considered for cosmetic benefits, but surgical intervention can alter the lung physiology or volumes and in turn leads to increase in physical capacity and exercise tolerance. Therefore, we conducted this to determine whether a surgical correction would restore the lung physiology, physical capacity and exercise tolerance in patients with kyphoscoliosis. To evaluate the usage of six-minute walk test scores and modified Borg scores as tools/measures for exercise tolerance in patients with spinal deformity and to study the effects of surgical correction of spinal deformity on exercise tolerance with above parameters as the measures. Thirty patients with spinal deformity, who had undergone surgery for deformity correction, were evaluated. All patients were investigated pre-operatively with x-rays of the spine (anteroposterior and lateral views). Clinical tests like breath holding time (after full inspiration) in number of seconds, modified Borg scores, six-minute walk test scores (heart rate, respiratory rate, maximum distance walked); were recorded as measures of exercise tolerance. The patients were followed up on the first, third, sixth and twelfth month post-operatively and tested clinically for breath holding time, modified Borg scores, six-minute walk test scores (heart rate, respiratory rate, maximum distance walked) and x-rays of the spine (anteroposterior and lateral views). In our study, breath holding time (p-value = 0.001) and modified Borg scores (p-value = 0.012) showed a significant improvement at 12 months post-operatively. We noted similar findings with heart rate, respiratory rate and maximum distance walked after a six-minute walk test. Improvements were noted in all the parameters, especially in the group of patients with greater than 60 degrees of cobb angle. However, the differences between the two groups (pre-operative cobb angle less than 60 degrees and pre-operative cobb angle more than 60 degrees) were not significant. The results were analysed and tested for significance using Student's t-test (paired and unpaired as appropriate) and Wilcoxon signed rank test. Surgical correction in cases of spinal deformity improves the cosmetic appearance and balance in the patients. Favourable results of surgical intervention were found in exercise tolerance with improvements in modified Borg scores, six-minute walk test results and breath holding time. The above parameters appear to be good tools for the assessment of physical capacity and exercise tolerance in patients with spinal deformity.

Matsubara-Takahashi cervix-holding technique for massive postpartum hemorrhage in patients with placenta previa with or without placenta accreta spectrum disorders.

PubMed

Takahashi, Hironori; Ohkuchi, Akihide; Usui, Rie; Suzuki, Hirotada; Baba, Yosuke; Matsubara, Shigeki

2018-03-01

To determine the efficacy and safety of the Matsubara-Takahashi cervix-holding technique (MT-holding) for achieving hemostasis for postpartum hemorrhage (PPH). The present retrospective observational study included data from deliveries that occurred between January 1, 2004, and December 31, 2014, at the Department of Obstetrics and Gynecology, Jichi Medical University, Shimotsuke, Japan. Deliveries were included where patients experienced blood loss greater than 2500 mL and MT-holding was used. The success rates of the technique in patients with placenta accreta spectrum (PAS) disorders and PPH were determined; subsequent pregnancy outcomes were also examined. There were 53 deliveries included in the study; 29 patients had placenta previa and 8 of these patients also had PAS disorders. MT-holding achieved hemostasis in 15 (71%) and 4 (50%) patients with placenta previa without and with PAS disorders, respectively; the placenta was removed in the latter. Overall, MT-holding achieved hemostasis in 40 (75%) deliveries. Of nine patients who became pregnant after this procedure, six went on to have full-term deliveries. MT-holding achieved hemostasis in 50% of patients with PAS disorders and had an overall success rate of 75% for PPH, comparable to other uterus-sparing procedures. MT-holding is suggested as a simple, effective, safe technique available to less-experienced obstetrician; these findings require confirmation in larger studies. © 2017 International Federation of Gynecology and Obstetrics.

Dose-response relationships of rabeprazole 5, 10, 20, and 40 mg once daily on suppression of gastric acid secretion through the night in healthy Japanese individuals with different CYP2C19 genotypes.

PubMed

Hayato, Seiichi; Hasegawa, Setsuo; Hojo, Seiichiro; Okawa, Hiroki; Abe, Hiroaki; Sugisaki, Nobuyuki; Munesue, Masahiro; Horai, Yukio; Ohnishi, Akihiro

2012-05-01

This study was designed to investigate the antisecretory activity of rabeprazole administered once daily in doses of 5, 10, 20, and 40 mg and different cytochrome P450 2C19 (CYP2C19) genotypes on gastric pH in healthy individuals. Additional objectives were delineating the nighttime from the daytime effect and determining the relationships between the pharmacokinetics and pharmacodynamics of rabeprazole. Eight individuals of each of the three genotypes of CYP2C19-homozygous extensive metabolizers (homo-EMs), heterozygous EMs (hetero-EMs), and poor metabolizers (PMs)-were recruited. Twenty-four individuals received a once-daily dose, with dosing interval 24 h of 5, 10, 20, or 40 mg rabeprazole for 5 days in a 4-period crossover fashion. Twenty-four-hour intragastric pH and plasma rabeprazole concentrations were determined on day 5. A dose-dependent increase in median pH and in pH 4 holding time was observed across all CYP2C19 genotypes. When rabeprazole was increased from 20 mg to 40 mg, the differences and 95% confidence intervals (CIs) of nighttime pH 4 holding time between 40 mg and 20 mg in homo-EMs, hetero-EMs, and PMs were 8.0% (-5.0% -21.0%), 28.7% (15.7% -41.6%), and 16.9% (3.9% -29.9%), respectively. The relationship between the area under the plasma concentration-time curve up to the last time point at which rabeprazole was quantifiable (AUC(0-t)) and the pH 4 holding time could be described using a sigmoid maximum effect (E(max)) model. Our data demonstrate that increasing rabeprazole dose up to 40 mg once daily results in an increasing pharmacodynamic effect, which is most apparent for the control of nocturnal gastric acid secretion.

Monte Carlo study of holding forces for tank cars on grades

DOT National Transportation Integrated Search

2013-04-15

This paper describes a numerical procedure to examine the holding forces needed to secure a cut of railroad tank cars staged on a grade during loading and unloading operations. Holding forces are created by applying emergency brake systems and blocki...

Gutenberg-Richter law for Internetquakes

NASA Astrophysics Data System (ADS)

Abe, Sumiyoshi; Suzuki, Norikazu

2003-03-01

The temporal behavior of the Internet is studied by performing Ping experiments. Sudden drastic changes in the Internet time series of round-trip times of the Ping signals (i.e., congestion of the network) are catastrophic and can be identified as “Internetquakes”. Magnitude of the Internetquakes is defined and the Gutenberg-Richter law is found to hold for the cumulative frequency of the Internetquakes and magnitude. Therefore, earthquakes, financial markets and the Internet share a common scale free nature in their temporal behaviors.

Impact of storage prior to cryopreservation on plasma membrane function and fertility of boar sperm.

PubMed

Guthrie, H D; Welch, G R

2005-01-15

Occasionally, boar semen must be shipped to another location for cryopreservation. We increased the initial holding time for the cooling of extended semen at 15 degrees C from 3 to 24 h to determine the effects on sperm characteristics and fertility. Thirty-one gilts and sows were inseminated once with subsequently cryopreserved and thawed semen. Increasing the holding time from 3 to 24 h had no significant effect on pregnancy rate 23 days after AI with frozen-thawed semen (64.5%) but decreased (P<0.05) embryo number from 15 to 9 and recovered embryos as fraction of CL from 73 to 47%. While the longer holding time at 15 degrees C did decrease potential litter size, the loss incurred was not too great to preclude the incorporation of a longer holding time into the cryopreservation protocol. An experiment was conducted to test the hypothesis that processing and freeze-thawing of boar semen would induce phospholipid scrambling in the plasma membrane similar to that evoked by incubation in bicarbonate-containing media. Merocyanine staining after incubation in the presence and absence of bicarbonate indicated that changes in plasma membrane phospholipid scrambling of processed and cryopreserved sperm differed from those in fresh semen undergoing bicarbonate-induced capacitation. The level of Annexin-V binding in boar spermatozoa increased from 1.6% in live spermatozoa in fresh semen to 18.7% in cryopreserved sperm. Apoptosis is unlikely to operate in mature spermatozoa. Apoptotic morphology in ejaculated spermatozoa is probably a result of incomplete deletion of apoptotic spermatocytes during spermatogenesis. Increased Annexin-V binding in thawed spermatozoa probably results from plasma membrane damage incurred during freezing and thawing.

Methods of Analysis by the U.S. Geological Survey National Water Quality Laboratory - Determination of Moderate-Use Pesticides and Selected Degradates in Water by C-18 Solid-Phase Extraction and Gas Chromatography/Mass Spectrometry

USGS Publications Warehouse

Sandstrom, Mark W.; Stroppel, Max E.; Foreman, William T.; Schroeder, Michael P.

2001-01-01

A method for the isolation and analysis of 21 parent pesticides and 20 pesticide degradates in natural-water samples is described. Water samples are filtered to remove suspended particulate matter and then are pumped through disposable solid-phase-extraction columns that contain octadecyl-bonded porous silica to extract the analytes. The columns are dried by using nitrogen gas, and adsorbed analytes are eluted with ethyl acetate. Extracted analytes are determined by capillary-column gas chromatography/mass spectrometry with selected-ion monitoring of three characteristic ions. The upper concentration limit is 2 micrograms per liter (?g/L) for most analytes. Single-operator method detection limits in reagent-water samples range from 0.00 1 to 0.057 ?g/L. Validation data also are presented for 14 parent pesticides and 20 degradates that were determined to have greater bias or variability, or shorter holding times than the other compounds. The estimated maximum holding time for analytes in pesticide-grade water before extraction was 4 days. The estimated maximum holding time for analytes after extraction on the dry solid-phase-extraction columns was 7 days. An optional on-site extraction procedure allows for samples to be collected and processed at remote sites where it is difficult to ship samples to the laboratory within the recommended pre-extraction holding time. The method complements existing U.S. Geological Survey Method O-1126-95 (NWQL Schedules 2001 and 2010) by using identical sample preparation and comparable instrument analytical conditions so that sample extracts can be analyzed by either method to expand the range of analytes determined from one water sample.

Sports-related lung injury during breath-hold diving.

PubMed

Mijacika, Tanja; Dujic, Zeljko

2016-12-01

The number of people practising recreational breath-hold diving is constantly growing, thereby increasing the need for knowledge of the acute and chronic effects such a sport could have on the health of participants. Breath-hold diving is potentially dangerous, mainly because of associated extreme environmental factors such as increased hydrostatic pressure, hypoxia, hypercapnia, hypothermia and strenuous exercise.In this article we focus on the effects of breath-hold diving on pulmonary function. Respiratory symptoms have been reported in almost 25% of breath-hold divers after repetitive diving sessions. Acutely, repetitive breath-hold diving may result in increased transpulmonary capillary pressure, leading to noncardiogenic oedema and/or alveolar haemorrhage. Furthermore, during a breath-hold dive, the chest and lungs are compressed by the increasing pressure of water. Rapid changes in lung air volume during descent or ascent can result in a lung injury known as pulmonary barotrauma. Factors that may influence individual susceptibility to breath-hold diving-induced lung injury range from underlying pulmonary or cardiac dysfunction to genetic predisposition.According to the available data, breath-holding does not result in chronic lung injury. However, studies of large populations of breath-hold divers are necessary to firmly exclude long-term lung damage. Copyright ©ERS 2016.

A study of the high temperature behavior of graphite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gale, H.; Zee, R. H.; Gale, W. F.

1997-01-10

Poco AXF 5Q graphite coupons were heated at temperatures ranging from 1900 K to 2400 K. A loss in weight was observed in all cases, but there appeared to be no simple relationship between the holding temperature and the weight loss observed. Scanning electron microscopy revealed no change in the surface morphology of the samples before and after heating, indicating that the loss of material occurred in a uniform, rather than a localized, fashion. The weight loss per hour, for pre-dried graphite coupons, was in most cases higher with short holding times than for prolonged exposure. Thus, it would appearmore » that the observed weight changes were dominated in most cases by the removal of volatiles rather than by the evaporation of carbon.« less

Fate of Escherichia coli O157:H7 in mechanically tenderized beef prime rib following searing, cooking and holding under commercial conditions

USDA-ARS?s Scientific Manuscript database

We evaluated the effect of commercial times/temperatures for searing, cooking, and holding for the destruction of Escherichia coli O157:H7 (ECOH) from mechanically tenderized prime rib. Boneless beef ribeye was inoculated on the fat side with ca. 5.7 log CFU/g of a five-strain cocktail of ECOH and t...

Public Utility Holding Company Act of 1935: 1935-1992

EIA Publications

1993-01-01

This report provides an economic and legislative history and analysis of the Public Utilities Holding Company Act (PUHCA) of 1935. This Act was substantially amended for the first time in 1992 by passage of the Energy Policy Act (EPACT). The report also includes a discussion of the issues which led to the amendment of PUHCA and projections of the impact of these changes on the electric industry.

Dezhurov holds a GTS electronics unit in Zvezda during Expedition Three

NASA Image and Video Library

2001-08-01

ISS003-E-5477 (August 2001) --- Cosmonaut Vladimir Dezhurov of Rosaviakosmos, Expedition Three flight engineer, holds a Global Time System (GTS) electronics unit in the Zvezda Service Module. Please note: The date identifiers on some frames are not accurate due to a technical problem with one of the Expedition Three cameras. When a specific date is given in the text or description portion, it is correct.

Measuring the Effectiveness of "The Major Decision": A Career Counseling Group for Undecided and Re-Deciding First Year, First-Generation College Students

ERIC Educational Resources Information Center

Wheeler, Melissa

2014-01-01

Researchers have reported that the graduation and retention rate of students whose parents do not hold college degrees (first-generation college students or FGCS) are lower than that of their peers whose parents do hold college degrees. FGCS are 1.3 times more likely to leave college after their first year compared to their non-FGCS peers…

When Can One Expect a Stronger Triangle Inequality?

ERIC Educational Resources Information Center

Faiziev, Valerii; Powers, Robert; Sahoo, Prasanna

2013-01-01

In 1997, Bailey and Bannister showed that a + b greater than c + h holds for all triangles with [gamma] less than arctan (22/7)where a, b, and c are the sides of the triangle, "h" is the altitude to side "c", and [gamma] is the angle opposite c. In this paper, we show that a + b greater than c + h holds approximately 92% of the time for all…

MR angiography of the renal artery: comparison of breath-hold two-dimensional phase-contrast cine technique with the phased-array coil and breath-hold two-dimensional time-of-flight technique with the body coil.

PubMed

Masui, T; Takehara, Y; Igarashi, T; Ichijo, K; Takahashi, M; Kaneko, M; Nozaki, A

1997-07-01

Breath-hold 2D phase-contrast (PC) cine MR angiography with a phased-array coil and 2D time-of-flight (TOF) MR angiography were performed in the renal arteries and their findings were compared. Breath-hold 2D thin slice PC and TOF MR angiography were performed in 10 normal volunteers for renal arteries. A PC technique with k-space segmentation was utilized with the phased-array coil. A PC technique provided visualization of the renal artery more distally than a TOF technique (4.8 +/- 0.5 cm vs. 3.7 +/- 0.8 cm). With cardiac triggering, distal renal arteries were well demonstrated in PC MR angiography. On PC images, up- or downward movements of the mid to distal renal arteries with aortic pulsatility were recognized. The quality of the images was better with the PC than with the TOF technique (3.4 vs. 2.7). The mid to distal portions of the renal arteries translationally move with aortic pulsatility. To consistently visualize and evaluate them on MR angiography, cardiac triggering might be required to reduce the effects of pulsatile motions of the renal artery in the use of a phased-array coil.

A chemodynamic approach for estimating losses of target organic chemicals from water during sample holding time

USGS Publications Warehouse

Capel, P.D.; Larson, S.J.

1995-01-01

Minimizing the loss of target organic chemicals from environmental water samples between the time of sample collection and isolation is important to the integrity of an investigation. During this sample holding time, there is a potential for analyte loss through volatilization from the water to the headspace, sorption to the walls and cap of the sample bottle; and transformation through biotic and/or abiotic reactions. This paper presents a chemodynamic-based, generalized approach to estimate the most probable loss processes for individual target organic chemicals. The basic premise is that the investigator must know which loss process(es) are important for a particular analyte, based on its chemodynamic properties, when choosing the appropriate method(s) to prevent loss.

A crisis in the analyst's life: self-containment, symbolization, and the holding space.

PubMed

Michelle, Flax

2011-04-01

Most analysts will experience some degree of crisis in the course of their working life. This paper explores the complex interplay between the analyst's affect during a crisis in her lifeü and the affective dynamics of the patient. The central question is "who or what holds the analyst"--especially in times of crisis. Symbolization of affect, facilitated by the analyst's self-created holding environment, is seen as a vital process in order for containment to take place. In the clinical case presented, the analyst's dog was an integral part of the analyst's self-righting through this difficult period; the dog functioned as an "analytic object" within the analysis.

What's on Your Mind? How Private Speech Mediates Cognition during Initial Non-Primary Language Learning

ERIC Educational Resources Information Center

Stafford, Catherine A.

2013-01-01

Vygotskian sociocultural theory of mind holds that language mediates thought. According to the theory, speech does not merely put completed thought into words; rather, it is a tool to refine thought as it evolves in real time. This study investigated from a sociocultural theory of mind perspective how nine beginning learners of Latin used private…

EFFECT OF DRY AIR CHILLING ON WARNER-BRATZLER SHEAR FORCE AND WATER-HOLDING CAPACITY OF BROILER MEAT DEBONED FOUR HOURS POSTMORTEM

USDA-ARS?s Scientific Manuscript database

TECHNICAL ABSTRACT Advantages of air chilling (AC) methods over immersion chilling (IC) methods in quality retention and improvement of deboned chicken breast meat depends on experimental conditions, such as deboning time. The objective of this study was to evaluate the effect of a dry-AC method on ...

Use of Clostridium perfringens as a fecal indicator to detect intertidal disposal at backcountry marine campsites in Prince William Sound, Alaska

Treesearch

Gino Graziano; Paul Twardock; Rusty Myers; Roman Dial; David Scheel

2007-01-01

Human waste disposal is a health concern in many backcountry areas. This study measured Clostridium perfringens in beach sediments of Prince William Sound, Alaska, to detect fecal contamination resulting from intertidal disposal. Analysis involved holding times that exceeded eight hours. In repeatedly sampled stored sediments, C. perfringens...

The Effects of Mothers' Past Infant-Holding Preferences on Their Adult Children's Face Processing Lateralisation

ERIC Educational Resources Information Center

Vervloed, Mathijs P. J.; Hendriks, Angelique W.; van den Eijnde, Esther

2011-01-01

Face processing development is negatively affected when infants have not been exposed to faces for some time because of congenital cataract blocking all vision (Le Grand, Mondloch, Maurer, & Brent, 2001). It is not clear, however, whether more subtle differences in face exposure may also have an influence. The present study looked at the effect of…

The competing risks Cox model with auxiliary case covariates under weaker missing-at-random cause of failure.

PubMed

Nevo, Daniel; Nishihara, Reiko; Ogino, Shuji; Wang, Molin

2017-08-04

In the analysis of time-to-event data with multiple causes using a competing risks Cox model, often the cause of failure is unknown for some of the cases. The probability of a missing cause is typically assumed to be independent of the cause given the time of the event and covariates measured before the event occurred. In practice, however, the underlying missing-at-random assumption does not necessarily hold. Motivated by colorectal cancer molecular pathological epidemiology analysis, we develop a method to conduct valid analysis when additional auxiliary variables are available for cases only. We consider a weaker missing-at-random assumption, with missing pattern depending on the observed quantities, which include the auxiliary covariates. We use an informative likelihood approach that will yield consistent estimates even when the underlying model for missing cause of failure is misspecified. The superiority of our method over naive methods in finite samples is demonstrated by simulation study results. We illustrate the use of our method in an analysis of colorectal cancer data from the Nurses' Health Study cohort, where, apparently, the traditional missing-at-random assumption fails to hold.

On intra-supply chain system with an improved distribution plan, multiple sales locations and quality assurance.

PubMed

Chiu, Singa Wang; Huang, Chao-Chih; Chiang, Kuo-Wei; Wu, Mei-Fang

2015-01-01

Transnational companies, operating in extremely competitive global markets, always seek to lower different operating costs, such as inventory holding costs in their intra- supply chain system. This paper incorporates a cost reducing product distribution policy into an intra-supply chain system with multiple sales locations and quality assurance studied by [Chiu et al., Expert Syst Appl, 40:2669-2676, (2013)]. Under the proposed cost reducing distribution policy, an added initial delivery of end items is distributed to multiple sales locations to meet their demand during the production unit's uptime and rework time. After rework when the remaining production lot goes through quality assurance, n fixed quantity installments of finished items are then transported to sales locations at a fixed time interval. Mathematical modeling and optimization techniques are used to derive closed-form optimal operating policies for the proposed system. Furthermore, the study demonstrates significant savings in stock holding costs for both the production unit and sales locations. Alternative of outsourcing product delivery task to an external distributor is analyzed to assist managerial decision making in potential outsourcing issues in order to facilitate further reduction in operating costs.

77 FR 2022 - Fisheries of the Northeastern United States; Spiny Dogfish Fishery; Commercial Period 2 Quota...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-13

... hr local time, January 13, 2012, through 2400 hr local time April 30, 2012. FOR FURTHER INFORMATION... vessels holding commercial Federal fisheries permits will be prohibited through 2400 hr local time, April...

Composite Case Development for Weapons Applications and Testing

DTIC Science & Technology

2015-03-01

5 cm axial location for each layer. ............................................................... 68  Figure 52.  Hydra radiographic time sequence...increase by 6.7%. No significant change in hold time was observed for the model with reduced mass. Figure 52. Hydra radiographic time sequence of

SU-F-P-14: Oxygen Inhalation Should Be the Conventional Approach in the Treatment of Thoracic and Abdominal Cancer by Radiotherapy with Active Breathing Control (ABC)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gong, G; Guo, Y; Yin, Y

Purpose: To investigate the feasibility and potential benefit of oxygen inhalation (OI) during radiotherapy applying an active breathing control (ABC) device, by analyzing the blood oxygen saturation (SpO2) and the instantaneous heart rate (IHR) variation in breath holding with OI and oxygen non-inhalation (ONI). Methods: The 27 healthy volunteers (16 males, 11 females) who were involved in this trial were all required to hold their breath for 10 times, non-inhaling and inhaling oxygen successively. The breath-holding time (BHT), rest time (RT), SpO2 and IHR under different oxygen status were recorded and compared. Results: The volunteers were divided into two groupsmore » according to SpO2 variations in breath-holding: group A (12 cases), with less than2% decline of SpO2; group B (15 cases), with a decline that surpassed 2%, and which could reach 3–6%. The BHT of group A, without inhaling oxygen, was significantly longer than that of group B (mean 33.77s Vs 30.51s, p<0.05); and was extended by 26.6% and 27.85%, after inhaling oxygen, in groups A and B, respectively. The SpO2 decreased in all volunteers during RT with ONI, to an extent that could reach up to 6%. The IHR of all volunteers showed the fast-slow-fast variation rule, and the oxygen had little effect. More than 70% of the volunteers stated that oxygen made them feel more comfortable and were more cooperative when ABC was used. Conclusion: The SpO2 declines during breath holding and RT could not be ignored while applying ABC, oxygen inhalation should become a conventional method with lengthening BHT and shortening RT, which yielded the benefit of improving the stability and reproducibility.« less

Sexual dimorphism of extensor carpi radialis muscle size, isometric force, relaxation rate and stamina during the breeding season of the frog Rana temporaria Linnaeus 1758.

PubMed

Navas, Carlos A; James, Rob S

2007-02-01

Mating success of individual male frogs within explosive breeding species can depend on their ability to compete for a mate and to hold onto that mate during amplexus. Such importance of amplexus has resulted in the evolution of sexual dimorphism in the morphology and contractile characteristics of the anuran forelimb muscles used during amplexus. The aims of our study were to use an explosive breeding frog (Rana temporaria) during the breeding season to compare extensor carpi radialis (ECR) muscle length, mass, isometric activation times, relaxation times, absolute force, relative force (stress) and fatigue between male and female frogs. We found that ECR muscle mass and length were greater (tenfold and 1.4-fold, respectively), absolute tetanic muscle force and relative tetanic force (stress) were greater (16-fold and 2.2-fold, respectively) and relaxation times were slower in males than in females. Male ECR muscles incompletely relaxed during fatigue tests and showed less fatigue than female muscles. These sex differences are likely to be beneficial to the male frogs in allowing them to produce relatively high absolute muscle forces for prolonged periods of time to hold onto their mate during amplexus.

Optimization of Injection Molding Parameters for HDPE/TiO2 Nanocomposites Fabrication with Multiple Performance Characteristics Using the Taguchi Method and Grey Relational Analysis

PubMed Central

Pervez, Hifsa; Mozumder, Mohammad S.; Mourad, Abdel-Hamid I.

2016-01-01

The current study presents an investigation on the optimization of injection molding parameters of HDPE/TiO2 nanocomposites using grey relational analysis with the Taguchi method. Four control factors, including filler concentration (i.e., TiO2), barrel temperature, residence time and holding time, were chosen at three different levels of each. Mechanical properties, such as yield strength, Young’s modulus and elongation, were selected as the performance targets. Nine experimental runs were carried out based on the Taguchi L9 orthogonal array, and the data were processed according to the grey relational steps. The optimal process parameters were found based on the average responses of the grey relational grades, and the ideal operating conditions were found to be a filler concentration of 5 wt % TiO2, a barrel temperature of 225 °C, a residence time of 30 min and a holding time of 20 s. Moreover, analysis of variance (ANOVA) has also been applied to identify the most significant factor, and the percentage of TiO2 nanoparticles was found to have the most significant effect on the properties of the HDPE/TiO2 nanocomposites fabricated through the injection molding process. PMID:28773830

Microstructural Evolution of Nanocrystalline ZrO2 in a Fe Matrix During High-Temperature Exposure

NASA Astrophysics Data System (ADS)

Raghavendra, K. G.; Dasgupta, Arup; Athreya, C. N.; Jayasankar, K.; Saroja, S.; Subramanya Sarma, V.

2018-06-01

The current study examines the evolution of nanocrystallites of ZrO2 with time and temperature in a Fe-ZrO2 composite. The crystallite sizes were determined through X-ray peak broadening analysis by the Williamson-Hall method together with dark field transmission electron microscopy. The ZrO2 crystallites were found to be stable and retained their sizes at 973 K and 1073 K for hold durations up to 600 minutes. On the other hand, the crystallites were seen to grow at 1173 K and reached up to 200 nm for a hold time of 600 minutes. The Ostwald ripening model was adopted to understand crystallite growth while a dislocation-driven pipe diffusion was adopted for understanding the kinetics of grain growth. The activation energy of grain growth was calculated as 379 kJ mol-1. The modeled and experimentally calculated size evolutions with time and temperature were shown to be in good agreement with each other. A detailed discussion on the kinetics and activation energy of grain growth of ZrO2 crystallites in a Fe matrix is presented in this manuscript.

Free-breathing quantification of hepatic fat in healthy children and children with nonalcoholic fatty liver disease using a multi-echo 3-D stack-of-radial MRI technique.

PubMed

Armstrong, Tess; Ly, Karrie V; Murthy, Smruthi; Ghahremani, Shahnaz; Kim, Grace Hyun J; Calkins, Kara L; Wu, Holden H

2018-05-04

In adults, noninvasive chemical shift encoded Cartesian magnetic resonance imaging (MRI) and single-voxel magnetic resonance (MR) spectroscopy (SVS) accurately quantify hepatic steatosis but require breath-holding. In children, especially young and sick children, breath-holding is often limited or not feasible. Sedation can facilitate breath-holding but is highly undesirable. For these reasons, there is a need to develop free-breathing MRI technology that accurately quantifies steatosis in all children. This study aimed to compare non-sedated free-breathing multi-echo 3-D stack-of-radial (radial) MRI versus standard breath-holding MRI and SVS techniques in a group of children for fat quantification with respect to image quality, accuracy and repeatability. Healthy children (n=10, median age [±interquartile range]: 10.9 [±3.3] years) and overweight children with nonalcoholic fatty liver disease (NAFLD) (n=9, median age: 15.2 [±3.2] years) were imaged at 3 Tesla using free-breathing radial MRI, breath-holding Cartesian MRI and breath-holding SVS. Acquisitions were performed twice to assess repeatability (within-subject mean difference, MD within ). Images and hepatic proton-density fat fraction (PDFF) maps were scored for image quality. Free-breathing and breath-holding PDFF were compared using linear regression (correlation coefficient, r and concordance correlation coefficient, ρ c ) and Bland-Altman analysis (mean difference). P<0.05 was considered significant. In patients with NAFLD, free-breathing radial MRI demonstrated significantly less motion artifacts compared to breath-holding Cartesian (P<0.05). Free-breathing radial PDFF demonstrated a linear relationship (P<0.001) versus breath-holding SVS PDFF and breath-holding Cartesian PDFF with r=0.996 and ρ c =0.994, and r=0.997 and ρ c =0.995, respectively. The mean difference in PDFF between free-breathing radial MRI, breath-holding Cartesian MRI and breath-holding SVS was <0.7%. Repeated free-breathing radial MRI had MD within =0.25% for PDFF. In this pediatric study, non-sedated free-breathing radial MRI provided accurate and repeatable hepatic PDFF measurements and improved image quality, compared to standard breath-holding MR techniques.

Evaluation of Manometric Measures during Tongue-Hold Swallows

ERIC Educational Resources Information Center

Doeltgen, Sebastian H.; Witte, Ulrike; Gumbley, Freya; Huckabee, Maggie-Lee

2009-01-01

Purpose: Based on visual inspection, prior research documented increased movement of the posterior pharyngeal wall in healthy volunteers during tongue-hold swallows. This manometric study investigated the immediate effects of the tongue-hold maneuver on pharyngeal peak pressure generation, duration of pressure generation, and pressure slope…

Cardiac Repolarization Changes in the Children with Breath-Holding Spells

PubMed Central

Amoozgar, Hamid; Saleh, Fazl; Farhani, Nahal; Rafiei, Mohammad; Inaloo, Soroor; Asadipooya, Ali-Akbar

2013-01-01

Objective Breath-holding spells are known as benign attacks, frequencies of which decrease by the development of the autonomic nervous system. The present study aims to compare the electrocardiographic repolarization in children with breath-holding spells. Methods In this study, QT dispersion, QTc dispersion, T peak to T end dispersion, and P wave dispersion of the twelve-lead surface electrocardiography of fifty children who had breath-holding spells were measured and compared with normal children from April 2011 to August 2012. Findings Forty-four (88%) patients had cyanotic spells, while 6 (12%) had pallid spells. QTc dispersion was increased in the patients with breath-holding spells (148.2±33.1) compared to the healthy children (132±27.3) and the difference was statically significant (P = 0.01). Meanwhile, no statistically significant differences were observed between the patients and the control subjects regarding the other parameters (P > 0.05). Conclusion QTc dispersion was significantly increased in the patients with breath-holding spells compared to normal children and this is a sign of cardiac repolarization abnormality as well as the increased risk of cardiac arrhythmia in patients with breath-holding spells. PMID:24910749

Robust sub-shot-noise measurement via Rabi-Josephson oscillations in bimodal Bose-Einstein condensates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tikhonenkov, I.; Vardi, A.; Moore, M. G.

2011-06-15

Mach-Zehnder atom interferometry requires hold-time phase squeezing to attain readout accuracy below the standard quantum limit. This increases its sensitivity to phase diffusion, restoring shot-noise scaling of the optimal signal-to-noise ratio in the presence of interactions. The contradiction between the preparations required for readout accuracy and robustness to interactions is removed by monitoring Rabi-Josephson oscillations instead of relative-phase oscillations during signal acquisition. Optimizing the signal-to-noise ratio with a Gaussian squeezed input, we find that hold-time number squeezing satisfies both demands and that sub-shot-noise scaling is retained even for strong interactions.

Human Factors Evaluation of the High Mobility Artillery Rocket System (HIMARS) in the Combined HIMARS-Guided Multiple Launch Rocket System (GMLRS) Initial Operational Test

DTIC Science & Technology

2007-05-01

and hand-holds: “The lack of handles on the ladder or adequate hand-holds to help crew members get on/off the cargo bed is unsafe.” (See appendix A...time 1 Why can’t the chief and gunner be in 4-meter circle at same time? Get rid of requirement. There is no safety issue. 2 Encountered no...warning lights. 1 HIMARS is a great piece of equipment all around although it can use a lot of work getting some additional “ bugs ” out and can still

Insulin Delivery System

NASA Technical Reports Server (NTRS)

1988-01-01

When Programmable Implantable Medication System (PIMS) is implanted in human body, it delivers precise programmed amounts of insulin over long periods of time. Mini-Med Technologies has been refining the Technologies since initial development at APL. The size of a hockey puck, and encased in titanium shell, PIMS holds about 2 1/2 teaspoons of insulin at a programmed basal rate. If a change in measured blood sugar level dictates a different dose, the patient can vary the amount of insulin delivered by holding a small radio transceiver over the implanted system and dialing in a specific program held in the PIMS computer memory. Insulin refills are accomplished approximately 4 times a year by hypodermic needle.

Modelling and optimization of semi-solid processing of 7075 Al alloy

NASA Astrophysics Data System (ADS)

Binesh, B.; Aghaie-Khafri, M.

2017-09-01

The new modified strain-induced melt activation (SIMA) process presented by Binesh and Aghaie-Khafri was optimized using a response surface methodology to improve the thixotropic characteristics of semi-solid 7075 alloy. The responses, namely the average grain size and the shape factor, were considered as functions of three independent input variables: effective strain, isothermal holding temperature and time. Mathematical models for the responses were developed using the regression analysis technique, and the adequacy of the models was validated by the analysis of variance method. The calculated results correlated fairly well with the experiments. It was found that all the first- and second-order terms of the independent parameters and the interactive terms of the effective strain and holding time were statistically significant for the responses. In order to simultaneously optimize the responses, the desirable values for the effective strain, holding temperature and time were predicted to be 5.1, 609 °C and 14 min, respectively, when employing the desirability function approach. Based on the optimization results, a significant improvement in the average grain size and shape factor of the semi-solid slurry prepared by the new modified SIMA process was observed.

Whole left ventricular functional assessment from two minutes free breathing multi-slice CINE acquisition

NASA Astrophysics Data System (ADS)

Usman, M.; Atkinson, D.; Heathfield, E.; Greil, G.; Schaeffter, T.; Prieto, C.

2015-04-01

Two major challenges in cardiovascular MRI are long scan times due to slow MR acquisition and motion artefacts due to respiratory motion. Recently, a Motion Corrected-Compressed Sensing (MC-CS) technique has been proposed for free breathing 2D dynamic cardiac MRI that addresses these challenges by simultaneously accelerating MR acquisition and correcting for any arbitrary motion in a compressed sensing reconstruction. In this work, the MC-CS framework is combined with parallel imaging for further acceleration, and is termed Motion Corrected Sparse SENSE (MC-SS). Validation of the MC-SS framework is demonstrated in eight volunteers and three patients for left ventricular functional assessment and results are compared with the breath-hold acquisitions as reference. A non-significant difference (P > 0.05) was observed in the volumetric functional measurements (end diastolic volume, end systolic volume, ejection fraction) and myocardial border sharpness values obtained with the proposed and gold standard methods. The proposed method achieves whole heart multi-slice coverage in 2 min under free breathing acquisition eliminating the time needed between breath-holds for instructions and recovery. This results in two-fold speed up of the total acquisition time in comparison to the breath-hold acquisition.

High bit rate germanium single photon detectors for 1310nm

NASA Astrophysics Data System (ADS)

Seamons, J. A.; Carroll, M. S.

2008-04-01

There is increasing interest in development of high speed, low noise and readily fieldable near infrared (NIR) single photon detectors. InGaAs/InP Avalanche photodiodes (APD) operated in Geiger mode (GM) are a leading choice for NIR due to their preeminence in optical networking. After-pulsing is, however, a primary challenge to operating InGaAs/InP single photon detectors at high frequencies1. After-pulsing is the effect of charge being released from traps that trigger false ("dark") counts. To overcome this problem, hold-off times between detection windows are used to allow the traps to discharge to suppress after-pulsing. The hold-off time represents, however, an upper limit on detection frequency that shows degradation beginning at frequencies of ~100 kHz in InGaAs/InP. Alternatively, germanium (Ge) single photon avalanche photodiodes (SPAD) have been reported to have more than an order of magnitude smaller charge trap densities than InGaAs/InP SPADs2, which allowed them to be successfully operated with passive quenching2 (i.e., no gated hold off times necessary), which is not possible with InGaAs/InP SPADs, indicating a much weaker dark count dependence on hold-off time consistent with fewer charge traps. Despite these encouraging results suggesting a possible higher operating frequency limit for Ge SPADs, little has been reported on Ge SPAD performance at high frequencies presumably because previous work with Ge SPADs has been discouraged by a strong demand to work at 1550 nm. NIR SPADs require cooling, which in the case of Ge SPADs dramatically reduces the quantum efficiency of the Ge at 1550 nm. Recently, however, advantages to working at 1310 nm have been suggested which combined with a need to increase quantum bit rates for quantum key distribution (QKD) motivates examination of Ge detectors performance at very high detection rates where InGaAs/InP does not perform as well. Presented in this paper are measurements of a commercially available Ge APD operated at relatively short GM hold-off times to examine whether there are potential advantages to using Ge for 1310 nm single photon detection. A weaker after-pulsing dependence on frequency is observed offering initial indications of the potential that Ge APDs might provide better high frequency performance.

Clinical Feasibility of Free-Breathing Dynamic T1-Weighted Imaging With Gadoxetic Acid-Enhanced Liver Magnetic Resonance Imaging Using a Combination of Variable Density Sampling and Compressed Sensing.

PubMed

Yoon, Jeong Hee; Yu, Mi Hye; Chang, Won; Park, Jin-Young; Nickel, Marcel Dominik; Son, Yohan; Kiefer, Berthold; Lee, Jeong Min

2017-10-01

The purpose of the study was to investigate the clinical feasibility of free-breathing dynamic T1-weighted imaging (T1WI) using Cartesian sampling, compressed sensing, and iterative reconstruction in gadoxetic acid-enhanced liver magnetic resonance imaging (MRI). This retrospective study was approved by our institutional review board, and the requirement for informed consent was waived. A total of 51 patients at high risk of breath-holding failure underwent dynamic T1WI in a free-breathing manner using volumetric interpolated breath-hold (BH) examination with compressed sensing reconstruction (CS-VIBE) and hard gating. Timing, motion artifacts, and image quality were evaluated by 4 radiologists on a 4-point scale. For patients with low image quality scores (<3) on the late arterial phase, respiratory motion-resolved (extradimension [XD]) reconstruction was additionally performed and reviewed in the same manner. In addition, in 68.6% (35/51) patients who had previously undergone liver MRI, image quality and motion artifacts on dynamic phases using CS-VIBE were compared with previous BH-T1WIs. In all patients, adequate arterial-phase timing was obtained at least once. Overall image quality of free-breathing T1WI was 3.30 ± 0.59 on precontrast and 2.68 ± 0.70, 2.93 ± 0.65, and 3.30 ± 0.49 on early arterial, late arterial, and portal venous phases, respectively. In 13 patients with lower than average image quality (<3) on the late arterial phase, motion-resolved reconstructed T1WI (XD-reconstructed CS-VIBE) significantly reduced motion artifacts (P < 0.002-0.021) and improved image quality (P < 0.0001-0.002). In comparison with previous BH-T1WI, CS-VIBE with hard gating or XD reconstruction showed less motion artifacts and better image quality on precontrast, arterial, and portal venous phases (P < 0.0001-0.013). Volumetric interpolated breath-hold examination with compressed sensing has the potential to provide consistent, motion-corrected free-breathing dynamic T1WI for liver MRI in patients at high risk of breath-holding failure.

Liver imaging at 3.0 T: diffusion-induced black-blood echo-planar imaging with large anatomic volumetric coverage as an alternative for specific absorption rate-intensive echo-train spin-echo sequences: feasibility study.

PubMed

van den Bos, Indra C; Hussain, Shahid M; Krestin, Gabriel P; Wielopolski, Piotr A

2008-07-01

Institutional Review Board approval and signed informed consent were obtained by all participants for an ongoing sequence optimization project at 3.0 T. The purpose of this study was to evaluate breath-hold diffusion-induced black-blood echo-planar imaging (BBEPI) as a potential alternative for specific absorption rate (SAR)-intensive spin-echo sequences, in particular, the fast spin-echo (FSE) sequences, at 3.0 T. Fourteen healthy volunteers (seven men, seven women; mean age +/- standard deviation, 32.7 years +/- 6.8) were imaged for this purpose. Liver coverage (20 cm, z-axis) was always performed in one 25-second breath hold. Imaging parameters were varied interactively with regard to echo time, diffusion b value, and voxel size. Images were evaluated and compared with fat-suppressed T2-weighted FSE images for image quality, liver delineation, geometric distortions, fat suppression, suppression of the blood signal, contrast-to-noise ratio (CNR), and signal-to-noise ratio (SNR). An optimized short- (25 msec) and long-echo (80 msec) BBEPI provided full anatomic, single breath-hold liver coverage (100 and 50 sections, respectively), with resulting voxel sizes of 3.3 x 2.7 x 2.0 mm and 3.3 x 2.7 x 4.0 mm, respectively. Repetition time was 6300 msec, matrix size was 160 x 192, and an acceleration factor of 2.00 was used. b Values of more than 20 sec/mm(2) showed better suppression of the blood signal but b values of 10 sec/mm(2) provided improved volume coverage and signal consistency. Compared with fat-suppressed T2-weighted FSE, the optimized BBEPI sequence provided (a) comparable image quality and liver delineation, (b) acceptable geometric distortions, (c) improved suppression of fat and blood signals, and (d) high CNR and SNR. BBEPI is feasible for fast, low-SAR, thin-section morphologic imaging of the entire liver in a single breath hold at 3.0 T. (c) RSNA, 2008.

Engineered, Spatially Varying Isothermal Holds: Enabling Combinatorial Studies of Temperature Effects, as Applied to Metastable Titanium Alloy β-21S

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martin, Brian; Samimi, Peyman; Collins, Peter

2017-06-01

A novel method to systematically vary temperature and thus study the resulting microstructure of a material is presented. This new method has the potential to be used in a combinatorial fashion, allowing the rapid study of thermal holds on microstructures to be conducted. This is demonstrated on a beta titanium alloy, where the thermal history has a strong effect on microstructure. It is informed by simulation and executed using the resistive heating capabilities of a Gleeble 3800 thermomechanical simulator. Spatially varying isothermal holds of 4 h were affected, where the temperature range of the multiple isothermal holds varied by ~175more » °C.« less

Face-to-face interference in typical and atypical development

PubMed Central

Riby, Deborah M; Doherty-Sneddon, Gwyneth; Whittle, Lisa

2012-01-01

Visual communication cues facilitate interpersonal communication. It is important that we look at faces to retrieve and subsequently process such cues. It is also important that we sometimes look away from faces as they increase cognitive load that may interfere with online processing. Indeed, when typically developing individuals hold face gaze it interferes with task completion. In this novel study we quantify face interference for the first time in Williams syndrome (WS) and Autism Spectrum Disorder (ASD). These disorders of development impact on cognition and social attention, but how do faces interfere with cognitive processing? Individuals developing typically as well as those with ASD (n = 19) and WS (n = 16) were recorded during a question and answer session that involved mathematics questions. In phase 1 gaze behaviour was not manipulated, but in phase 2 participants were required to maintain eye contact with the experimenter at all times. Looking at faces decreased task accuracy for individuals who were developing typically. Critically, the same pattern was seen in WS and ASD, whereby task performance decreased when participants were required to hold face gaze. The results show that looking at faces interferes with task performance in all groups. This finding requires the caveat that individuals with WS and ASD found it harder than individuals who were developing typically to maintain eye contact throughout the interaction. Individuals with ASD struggled to hold eye contact at all points of the interaction while those with WS found it especially difficult when thinking. PMID:22356183

Cooling rate and stress relaxation in silica melts and glasses via microsecond molecular dyanmics

DOE PAGES

Lane, J. Matthew D.

2015-07-22

We have conducted extremely long molecular dynamics simulations of glasses to microsecond times, which close the gap between experimental and atomistic simulation time scales by two to three orders of magnitude. The static, thermal, and structural properties of silica glass are reported for glass cooling rates down to 5×10 9 K/s and viscoelastic response in silica melts and glasses are studied over nine decades of time. We finally present results from relaxation of hydrostatic compressive stress in silica and show that time-temperature superposition holds in these systems for temperatures from 3500 to 1000 K.

Evaluation of nonpoint-source contamination, Wisconsin: Selected data for 1992 water year

USGS Publications Warehouse

Graczyk, D.J.; Walker, J.F.; Greb, S.R.; Corsi, Steven R.; Owens, D.W.

1993-01-01

This report presents the annual results of the U.S. Geological Survey's (USGS) watershed-management evaluation monitoring program in Wisconsin. The overall objective of each individual project in the program is to determine if the water chemistry in the receiving stream has changed as a result of the implementation of land-management practices in the watershed. This is accomplished through monitoring of water chemistry and ancillary variables before best-management practices (BMP's) are installed ('pre-BMP'), during installation ('transitional'), and after ('post-BMP') watershed- management plans have been completely implemented. Fecal-coliform (FC) counts ranged between 10 and 310,00/100 mL. A large range of values occurred within duplicate and triplicate samples as well as over time. The median percentage difference between duplicate and triplicate samples was 17 percent although 4 out of the total 60 duplicate and triplicate samples had differences greater than 100 percent. A decrease in FC counts generally occurred over the duration of the 4-day analyses. Linear regression models of the log-concentration values (dependent variable) with respect to time (independent variable) were calculated for all samples. Negative slopes were found for 14 of the 15 samples. Slopes varied from +0.5 to -38.4 percent gain/loss/day, with a median slope of -8.5 percent/day. A t-test was applied to the data to examine whether or not significant differences in FC counts exist with respect to holding times. Because the T-test only compares two treatments, the test was conducted 3 times (0 versus 24-hr holding time, 0 versus 48-hr holding time, and 0 versus 72-hr holding time). Setting the level of significance at p less than 0.05 and assuming equal variances, 27 percent (all from Bower and Otter Creeks) of the samples demonstrated a significant difference in colony count over the first 24 hr, 40 percent over 48 hr, and 47 percent over 72 hr. All samples that exhibited a significant change in colony count were because of a decrease in colony count of the sample.

Excreted Thiocyanate Detects Live Reef Fishes Illegally Collected Using Cyanide—A Non-Invasive and Non-Destructive Testing Approach

PubMed Central

Vaz, Marcela C. M.; Rocha-Santos, Teresa A. P.; Rocha, Rui J. M.; Lopes, Isabel; Pereira, Ruth; Duarte, Armando C.; Rubec, Peter J.; Calado, Ricardo

2012-01-01

Cyanide fishing is a method employed to capture marine fish alive on coral reefs. They are shipped to markets for human consumption in Southeast Asia, as well as to supply the marine aquarium trade worldwide. Although several techniques can be used to detect cyanide in reef fish, there is still no testing method that can be used to survey the whole supply chain. Most methods for cyanide detection are time-consuming and require the sacrifice of the sampled fish. Thiocyanate anion (SCN−) is a metabolite produced by the main metabolic pathway for cyanide anion (CN−) detoxification. Our study employed an optical fiber (OF) methodology (analytical time <6 min) to detect SCN− in a non-invasive and non-destructive manner. Our OF methodology is able to detect trace levels (>3.16 µg L−1) of SCN− in seawater. Given that marine fish exposed to cyanide excrete SCN− in the urine, elevated levels of SCN− present in the seawater holding live reef fish indicate that the surveyed specimens were likely exposed to cyanide. In our study, captive-bred clownfish (Amphiprion clarkii) pulse exposed for 60 s to either 12.5 or 25 mg L−1 of CN− excreted up to 6.96±0.03 and 9.84±0.03 µg L−1 of SCN−, respectively, during the 28 days following exposure. No detectable levels of SCN− were recorded in the water holding control organisms not exposed to CN−, or in synthetic seawater lacking fish. While further research is necessary, our methodology can allow a rapid detection of SCN− in the holding water and can be used as a screening tool to indicate if live reef fish were collected with cyanide. PMID:22536375

Excreted thiocyanate detects live reef fishes illegally collected using cyanide--a non-invasive and non-destructive testing approach.

PubMed

Vaz, Marcela C M; Rocha-Santos, Teresa A P; Rocha, Rui J M; Lopes, Isabel; Pereira, Ruth; Duarte, Armando C; Rubec, Peter J; Calado, Ricardo

2012-01-01

Cyanide fishing is a method employed to capture marine fish alive on coral reefs. They are shipped to markets for human consumption in Southeast Asia, as well as to supply the marine aquarium trade worldwide. Although several techniques can be used to detect cyanide in reef fish, there is still no testing method that can be used to survey the whole supply chain. Most methods for cyanide detection are time-consuming and require the sacrifice of the sampled fish. Thiocyanate anion (SCN(-)) is a metabolite produced by the main metabolic pathway for cyanide anion (CN(-)) detoxification. Our study employed an optical fiber (OF) methodology (analytical time <6 min) to detect SCN(-) in a non-invasive and non-destructive manner. Our OF methodology is able to detect trace levels (>3.16 µg L(-1)) of SCN(-) in seawater. Given that marine fish exposed to cyanide excrete SCN(-) in the urine, elevated levels of SCN(-) present in the seawater holding live reef fish indicate that the surveyed specimens were likely exposed to cyanide. In our study, captive-bred clownfish (Amphiprion clarkii) pulse exposed for 60 s to either 12.5 or 25 mg L(-1) of CN(-) excreted up to 6.96±0.03 and 9.84±0.03 µg L(-1) of SCN(-), respectively, during the 28 days following exposure. No detectable levels of SCN(-) were recorded in the water holding control organisms not exposed to CN(-), or in synthetic seawater lacking fish. While further research is necessary, our methodology can allow a rapid detection of SCN(-) in the holding water and can be used as a screening tool to indicate if live reef fish were collected with cyanide.

Proof of Concept to Isolate and Culture Primary Muscle Cells from Northern Elephant Seals to Study the Mechanisms that Maintain Aerobic Metabolism Under the Hypoxic Conditions of Breath-hold Diving

DTIC Science & Technology

2013-09-30

Cells from Northern Elephant Seals to Study the Mechanisms that Maintain Aerobic Metabolism Under the Hypoxic Conditions of Breath-hold Diving...Muscle Cells from Northern Elephant Seals to Study the Mechanisms that Maintain Aerobic Metabolism Under the Hypoxic Conditions of Breath-hold Diving 5a...two day period in September, 2012. The first major huddle to the study was to determine the effect of the overnight shipping of the viability of

Synthesis fidelity and time-varying spectral change in vowels

NASA Astrophysics Data System (ADS)

Assmann, Peter F.; Katz, William F.

2005-02-01

Recent studies have shown that synthesized versions of American English vowels are less accurately identified when the natural time-varying spectral changes are eliminated by holding the formant frequencies constant over the duration of the vowel. A limitation of these experiments has been that vowels produced by formant synthesis are generally less accurately identified than the natural vowels after which they are modeled. To overcome this limitation, a high-quality speech analysis-synthesis system (STRAIGHT) was used to synthesize versions of 12 American English vowels spoken by adults and children. Vowels synthesized with STRAIGHT were identified as accurately as the natural versions, in contrast with previous results from our laboratory showing identification rates 9%-12% lower for the same vowels synthesized using the cascade formant model. Consistent with earlier studies, identification accuracy was not reduced when the fundamental frequency was held constant across the vowel. However, elimination of time-varying changes in the spectral envelope using STRAIGHT led to a greater reduction in accuracy (23%) than was previously found with cascade formant synthesis (11%). A statistical pattern recognition model, applied to acoustic measurements of the natural and synthesized vowels, predicted both the higher identification accuracy for vowels synthesized using STRAIGHT compared to formant synthesis, and the greater effects of holding the formant frequencies constant over time with STRAIGHT synthesis. Taken together, the experiment and modeling results suggest that formant estimation errors and incorrect rendering of spectral and temporal cues by cascade formant synthesis contribute to lower identification accuracy and underestimation of the role of time-varying spectral change in vowels. .

Acetylcholinesterase inhibition in the threeridge mussel (Amblema plicata) by chlorpyrifos: implications for biomonitoring

USGS Publications Warehouse

Doran, W.J.; Cope, W.G.; Rada, R.G.; Sandheinrich, M.B.

2001-01-01

The effects of chlorpyrifos, an organophosphorus insecticide, were examined on the activity of the nervous system enzyme acetylcholinesterase (AChE) in the threeridge mussel Amblema plicata in a 24-day laboratory test. Thirty-six mussels in each of seven treatments (18 mussels per duplicate) were exposed to chlorpyrifos (0.1, 0.2, 0.3, 0.6, and 1.2 mg/L), a solvent (acetone), and a solvent-free (well water) control for 12, 24, or 96 h. The activity of AChE was measured in the anterior adductor muscle of eight mussels from each treatment after exposure. To assess potential latent effects, six mussels from each treatment were removed after 24 h of exposure and transferred to untreated water for a 21-day holding period; AChE activity was measured on three mussels from each treatment at 7 and 21 days of the holding period. The activity of AChE in chlorpyrifos-exposed mussels did not differ from controls after 12 or 24 h of exposure (t- test, P>0.05), but was significantly less than controls after 96 h (t- test, P=0.01). AChE activity did not vary among mussels at 24 h of exposure (i.e., Day 0 of holding period) and those at Day 7 and Day 21 of the holding period. Overall changes in AChE activity of mussels during the test were unrelated to individual chlorpyrifos concentrations and exposure times (repeated measure ANOVA; (P=0.06). A power analysis revealed that the sample size must be increased from 2 to 5 replicates (8 to 20 mussels per time interval and test concentration) to increase the probability of detecting significant differences in AChE activity. This calculated increase in sample size has potential implications for future biomonitoring studies with chlorpyrifos and unionid mussels.

High-temperature, low-cycle fatigue of advanced copper-base alloys for rocket nozzles. Part 2: NASA 1.1, Glidcop, and sputtered copper alloys

NASA Technical Reports Server (NTRS)

Conway, J. B.; Stentz, R. H.; Berling, J. T.

1974-01-01

Short-term tensile and low-cycle fatigue data are reported for five advance copper-base alloys: Sputtered Zr-Cu as received, sputtered Zr-Cu heat-treated, Glidcop AL-10, and NASA alloys 1-1A and 1-1B. Tensile tests were performed in argon at 538 C using an axial strain rate of 0.002/sec. Yield strength and ultimate tensile strength data are reported along with reduction in area values. Axial strain controlled low-cycle fatigue tests were performed in argon at 538C using an axial strain rate of 0.002/sec to define the fatigue life over the range from 100 to 3000 cycles for the five materials studied. It was found that the fatigue characteristics of the NASA 1-1A and NASA 1-1B compositions are identical and represent fatique life values which are much greater than those for the other materials tested. The effect of temperature on NASA 1-1B alloy at a strain rate of 0.002/sec was evaluated along with the effect of strain rates of 0.0004 and 0.01/sec at 538 C. Hold-time data are reported for the NASA 1-1B alloy at 538 C using 5 minute hold periods in tension only and compression only at two different strain range values. Hold periods in tension were much more detrimental than hold periods in compression.

High voltage holding in the negative ion sources with cesium deposition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Belchenko, Yu.; Abdrashitov, G.; Ivanov, A.

High voltage holding of the large surface-plasma negative ion source with cesium deposition was studied. It was found that heating of ion-optical system electrodes to temperature >100 °C facilitates the source conditioning by high voltage pulses in vacuum and by beam shots. The procedure of electrode conditioning and the data on high-voltage holding in the negative ion source with small cesium seed are described. The mechanism of high voltage holding improvement by depletion of cesium coverage is discussed.

A Haptic Guided Robotic System for Endoscope Positioning and Holding.

PubMed

Cabuk, Burak; Ceylan, Savas; Anik, Ihsan; Tugasaygi, Mehtap; Kizir, Selcuk

2015-01-01

To determine the feasibility, advantages, and disadvantages of using a robot for holding and maneuvering the endoscope in transnasal transsphenoidal surgery. The system used in this study was a Stewart Platform based robotic system that was developed by Kocaeli University Department of Mechatronics Engineering for positioning and holding of endoscope. After the first use on an artificial head model, the system was used on six fresh postmortem bodies that were provided by the Morgue Specialization Department of the Forensic Medicine Institute (Istanbul, Turkey). The setup required for robotic system was easy, the time for registration procedure and setup of the robot takes 15 minutes. The resistance was felt on haptic arm in case of contact or friction with adjacent tissues. The adaptation process was shorter with the mouse to manipulate the endoscope. The endoscopic transsphenoidal approach was achieved with the robotic system. The endoscope was guided to the sphenoid ostium with the help of the robotic arm. This robotic system can be used in endoscopic transsphenoidal surgery as an endoscope positioner and holder. The robot is able to change the position easily with the help of an assistant and prevents tremor, and provides a better field of vision for work.

The Simulation of Precipitation Evolutions and Mechanical Properties in Friction Stir Welding with Post-Weld Heat Treatments

NASA Astrophysics Data System (ADS)

Zhang, Z.; Wan, Z. Y.; Lindgren, L.-E.; Tan, Z. J.; Zhou, X.

2017-12-01

A finite element model of friction stir welding capable of re-meshing is used to simulate the temperature variations. Re-meshing of the finite element model is used to maintain a fine mesh resolving the gradients of the solution. The Kampmann-Wagner numerical model for precipitation is then used to study the relation between friction stir welds with post-weld heat treatment (PWHT) and the changes in mechanical properties. Results indicate that the PWHT holding time and PWHT holding temperature need to be optimally designed to obtain FSW with better mechanical properties. Higher precipitate number with lower precipitate sizes gives higher strength in the stirring zone after PWHT. The coarsening of precipitates in HAZ are the main reason to hinder the improvement of mechanical property when PWHT is used.

Optimal policy for profit maximising in an EOQ model under non-linear holding cost and stock-dependent demand rate

NASA Astrophysics Data System (ADS)

Pando, V.; García-Laguna, J.; San-José, L. A.

2012-11-01

In this article, we integrate a non-linear holding cost with a stock-dependent demand rate in a maximising profit per unit time model, extending several inventory models studied by other authors. After giving the mathematical formulation of the inventory system, we prove the existence and uniqueness of the optimal policy. Relying on this result, we can obtain the optimal solution using different numerical algorithms. Moreover, we provide a necessary and sufficient condition to determine whether a system is profitable, and we establish a rule to check when a given order quantity is the optimal lot size of the inventory model. The results are illustrated through numerical examples and the sensitivity of the optimal solution with respect to changes in some values of the parameters is assessed.

NEO Test Stand Analysis

NASA Technical Reports Server (NTRS)

Pike, Cody J.

2015-01-01

A project within SwampWorks is building a test stand to hold regolith to study how dust is ejected when exposed to the hot exhaust plume of a rocket engine. The test stand needs to be analyzed, finalized, and fabrication drawings generated to move forward. Modifications of the test stand assembly were made with Creo 2 modeling software. Structural analysis calculations were developed by hand to confirm if the structure will hold the expected loads while optimizing support positions. These calculations when iterated through MatLab demonstrated the optimized position of the vertical support to be 98'' from the far end of the stand. All remaining deflections were shown to be under the 0.6'' requirement and internal stresses to meet NASA Ground Support Equipment (GSE) Safety Standards. Though at the time of writing, fabrication drawings have yet to be generated, but are expected shortly after.

Active hold-down for heat treating

NASA Technical Reports Server (NTRS)

Collins, E. R., Jr. (Inventor)

1986-01-01

The object of the disclosure is to provide a vacuum hold-down for holding thin sheets to a support surface, which permits the thin sheet to change dimensions as it is held down. The hold-down includes numerous holes in the support surface, through which a vacuum is applied from a vacuum source. The holes are arranged in zones. The vacuum is repeatedly interrupted at only one or a few zones, while it continues to be applied to other zones, to allow the workpiece to creep along that interrupted zone. The vacuum to different zones is interrupted at different times, as by a slowly turning valve number, to allow each zone of the workpiece to creep. A positive pressure may be applied from a pressured air source to a zone when the vacuum is interrupted there, to help lift the corresponding workpiece zone off the surface to aid in creeping. The workpiece may undergo dimensional changes because of heating, cooling, drying, or other procedure.

No Certification, No Training...No Problem: The Influence of Formative Beliefs and Learning Experiences in the Instructional Practice of New Independent School Teachers

ERIC Educational Resources Information Center

Smith, Derick Graham

2012-01-01

This study sought to answer the question: "To what extent do prior beliefs about and experiences of teaching and learning influence the instructional practices of new independent school teachers," who are generally not required to have any formal pedagogical training or hold teacher certification prior to beginning full-time employment.…

America's Great Books Colleges and Their Curious Histories of Success, Struggle, and Failure

ERIC Educational Resources Information Center

Cubbage, Kent T.

2009-01-01

The Great Books hold a special place in scholarly and academic lore in America. Study of the Great Books and liberal education in general were the foundation of a college education since the colonial times, but yielded to electives and other academic trends during the early portion of the twentieth century. By the 1930s, several men sought to…

Chemistry and Physics of Solid Surfaces 5

DTIC Science & Technology

1984-04-01

associated with dimers and trimers, Type 2 particles form large clusters of 2000-5000 A size in aqueous solution. Luminescence studies carried out with...and rates of energy transfer, real time measurements using ultrashort laser pulses hold great promise. With the possible exception of the stimulated...the dynamic prop- erties of such clusters . The clusters are not stationary entities as origi- nally envisioned. Instead even fairly large aggregates

Wives and Daughters: The Differential Role of Day Care Use in the Nursing Home Placement of Cognitively Impaired Family Members

ERIC Educational Resources Information Center

Cho, Soyeon; Zarit, Steven H.; Chiriboga, David A.

2009-01-01

Purpose: To expand knowledge concerning the significance of kin relationships in caregiving, this study assessed predictors of the timing of institutionalization for persons with dementia. The focus was on whether use of adult day care by wives and daughters holds the same implications for placement. Design and Methods: Guided by a caregiving…

Passion and Preparation in the Basic Course: The Influence of Students' Ego-Involvement with Speech Topics and Preparation Time on Public-Speaking Grades

ERIC Educational Resources Information Center

Mazer, Joseph P.; Titsworth, Scott

2012-01-01

Authors of basic public-speaking course textbooks frequently encourage students to select speech topics in which they have vested interest, care deeply about, and hold strong opinions and beliefs. This study explores students' level of ego-involvement with informative and persuasive speech topics, examines possible ego-involvement predictors of…

Mothers' experience of their contact with their stillborn infant: an interpretative phenomenological analysis.

PubMed

Ryninks, Kirsty; Roberts-Collins, Cara; McKenzie-McHarg, Kirstie; Horsch, Antje

2014-06-13

Guidelines surrounding maternal contact with the stillborn infant have been contradictory over the past thirty years. Most studies have reported that seeing and holding the stillborn baby is associated with fewer anxiety and depressive symptoms among mothers of stillborn babies than not doing so. In contrast, others studies suggest that contact with the stillborn infant can lead to poorer maternal mental health outcomes. There is a lack of research focusing on the maternal experience of this contact. The present study aimed to investigate how mothers describe their experience of spending time with their stillborn baby and how they felt retrospectively about the decision they made to see and hold their baby or not. In depth interviews were conducted with twenty-one mothers three months after stillbirth. All mothers had decided to see and the majority to hold their baby. Qualitative analysis of the interview data was performed using Interpretive Phenomenological Analysis. Six superordinate themes were identified: Characteristics of Contact, Physicality; Emotional Experience; Surreal Experience; Finality; and Decision. Having contact with their stillborn infant provided mothers with time to process what had happened, to build memories, and to 'say goodbye', often sharing the experience with partners and other family members. The majority of mothers felt satisfied with their decision to spend time with their stillborn baby. Several mothers talked about their fear of seeing a damaged or dead body. Some mothers experienced strong disbelief and dissociation during the contact. Results indicate that preparation before contact with the baby, professional support during the contact, and professional follow-up are crucial in order to prevent the development of maternal mental health problems. Fears of seeing a damaged or dead body should be sensitively explored and ways of coping discussed. Even in cases where mothers experienced intense distress during the contact with their stillborn baby, they still described that having had this contact was important and that they had taken the right decision. This indicates a need for giving parents an informed choice by engaging in discussions about the possible benefits and risks of seeing their stillborn baby.

Pyrolysis of Lantana camara and Mimosa pigra: Influences of temperature, other process parameters and incondensable gas evolution on char yield and higher heating value.

PubMed

Mundike, Jhonnah; Collard, François-Xavier; Görgens, Johann F

2017-11-01

Pyrolysis of invasive non-indigenous plants, Lantana camara (LC) and Mimosa pigra (MP) was conducted at milligram-scale for optimisation of temperature, heating rate and hold time on char yield and higher heating value (HHV). The impact of scaling-up to gram-scale was also studied, with chromatography used to correlate gas composition with HHV evolution. Statistically significant effects of temperature on char yield and HHV were obtained, while heating rate and hold time effects were insignificant. Milligram-scale maximised HHVs were 30.03MJkg -1 (525°C) and 31.01MJkg -1 (580°C) for LC and MP, respectively. Higher char yields and HHVs for MP were attributed to increased lignin content. Scaling-up promoted secondary char formation thereby increasing HHVs, 30.82MJkg -1 for LC and 31.61MJkg -1 for MP. Incondensable gas analysis showed that temperature increase beyond preferred values caused dehydrogenation that decreased HHV. Similarly, CO evolution profile explained differences in optimal HHV temperatures. Copyright © 2017 Elsevier Ltd. All rights reserved.

Lead recovery from waste CRT funnel glass by high-temperature melting process.

PubMed

Hu, Biao; Hui, Wenlong

2018-02-05

In this research, a novel and effective process for waste CRT funnel glass treatment was developed. The key to this process is removal of lead from the CRT funnel glass by high-temperature melting process. Sodium carbonate powder was used as a fusion agent, sodium sulfide serves as a catalytic agent and carbon powder acts as reducing agent. Experimental results showed that lead recovery rate increased with an increase in the amount of added sodium carbonate, sodium sulfide, carbonate, temperature and holding time initially, and then reached a stable value. The maximum lead recovery rate was approximately 94%, when the optimum adding amount of sodium carbonate, sodium sulfide, carbonate, temperature and holding time were 25%, 8%, 3.6%, 1200°C and 120min, respectively. In the high-temperature melting process, lead silicate in the funnel glass was firstly reduced, and then removed. The glass slag can be made into sodium and potassium silicate by hydrolysis process. This study proposed a practical and economical process for recovery of lead and utilization of waste glass slag. Copyright © 2017 Elsevier B.V. All rights reserved.

Cryogenic and elevated temperature strengths of an Al-Zn-Mg-Cu alloy modified with Sc and Zr

NASA Astrophysics Data System (ADS)

Senkova, S. V.; Senkov, O. N.; Miracle, D. B.

2006-12-01

The effect of minor additions of Sc and Zr on tensile properties of two developmental Al-Zn-Mg-Cu alloys was studied in the temperature range -196°C to 300°C. Due to the presence of Sc and Zr in a fine dispersoid form, both low-temperature and elevated temperature strengths of these alloys are much higher than those of similar 7000 series alloys that do not contain these elements. After short holding times (up to 10 hours) at 205°C, the strength of these alloys is higher than those of high-temperature Al alloys 2219-T6 and 2618-T6; however, the latter alloys show better strength after longer holding times. It is suggested that additional alloying of the Sc-containing Al-Zn-Mg-Cu alloys with other dispersoid-forming elements, such as Ni, Fe, Mn, and Si, with a respective decrease in the amounts of Zn and Mg may further improve the elevated temperature strength and decrease the loss of strength with extended elevated temperature exposure.

Robotic hand with locking mechanism using TCP muscles for applications in prosthetic hand and humanoids

NASA Astrophysics Data System (ADS)

Saharan, Lokesh; Tadesse, Yonas

2016-04-01

This paper presents a biomimetic, lightweight, 3D printed and customizable robotic hand with locking mechanism consisting of Twisted and Coiled Polymer (TCP) muscles based on nylon precursor fibers as artificial muscles. Previously, we have presented a small-sized biomimetic hand using nylon based artificial muscles and fishing line muscles as actuators. The current study focuses on an adult-sized prosthetic hand with improved design and a position/force locking system. Energy efficiency is always a matter of concern to make compact, lightweight, durable and cost effective devices. In natural human hand, if we keep holding objects for long time, we get tired because of continuous use of energy for keeping the fingers in certain positions. Similarly, in prosthetic hands we also need to provide energy continuously to artificial muscles to hold the object for a certain period of time, which is certainly not energy efficient. In this work we, describe the design of the robotic hand and locking mechanism along with the experimental results on the performance of the locking mechanism.

The influence of the cumulated deformation energy in the measurement by the DSI method on the selected mechanical properties of bone tissues.

PubMed

Makuch, Anna M; Skalski, Konstanty R; Pawlikowski, Marek

2017-01-01

The goal of the study was to determine the influence of DSI test conditions, i.e., loading/unloading rates, hold time, and the value of the maximum loading force on selected mechanical properties of trabecular bone tissue. The test samples were resected from a femoral head of a patient qualified for a hip replacement surgery. During the DSI tests hardness (HV, HM, HIT) and elastic modulus (EIT) of trabecular bone tissue were measured using the Micro Hardness Tester (MHT, CSEM). The analysis of the results of measurements and the calculations of total energy, i.e., elastic and inelastic (Wtotal, Welastic, Winelastic) and those of hardness and elasticity made it possible to assess the impact of the process parameters (loading velocity, force and hold time) on mechanical properties of bone structures at a microscopic level. The coefficient k dependent on the EIT/HIT ratio and on the stored energy (ΔW = Wtotal - Welastic) is a measure of the material reaction to the loading and the deformation of tissue.

The telescopes of Duke Ernst I, the Pious, of Saxony-Gotha. (German Title: Die Fernrohre von Herzog Ernst I., dem Frommen, von Sachsen-Gotha)

NASA Astrophysics Data System (ADS)

Keil, Inge

Already in the 17th century, there was an interest in astronomy at the court of Gotha, where Duke Ernst I hold one of the largest collections of telescopes at his times, with instruments made by the Augsburg optician Johann Wiesel, by Baruch Spinoza and others. By the help of the inventory of the Kunstkammer the holdings may be documentarily demonstrated.

Development enhances hypometabolism in northern elephant seal pups (Mirounga angustirostris)

PubMed Central

Tift, Michael S.; Ranalli, Elizabeth C.; Houser, Dorian S.; Ortiz, Rudy M.; Crocker, Daniel E.

2013-01-01

Summary Investigation into the development of oxygen storage capacity in air-breathing marine predators has been performed, but little is known about the development of regulatory factors that influence oxygen utilization. Strategies for efficiently using oxygen stores should enable marine predators to optimize time spent foraging underwater. We describe the developmental patterns of oxygen use during voluntary breath-holds in northern elephant seals (Mirounga angustirostris) at 2 and 7 weeks post-weaning. We measured 1) changes in oxygen consumption (VO2), and 2) changes in venous pH, partial pressure of oxygen (pO2), haemoglobin saturation (sO2), oxygen content (O2ct), partial pressure of carbon dioxide (pCO2), haematocrit (Hct) and total haemoglobin (tHb). To examine the effect of the dive response on the development of oxygen utilization, voluntary breath-hold experiments were conducted in and out of water. Suppression of VO2 during voluntary breath-holds increased significantly between 2 and 7 weeks post-weaning, reaching a maximum suppression of 53% below resting metabolic rate and 56% below Kleiber’s standard metabolic rate. From 2 to 7 weeks post-weaning, breath-hold VO2 was reduced by 52%. Between the two age classes, this equates to a mean breath-hold VO2 reduction of 16% from resting VO2. Breath-hold VO2 also declined with increasing breath-hold duration, but there was no direct effect of voluntary submergence on reducing VO2. Age did not influence rates of venous pO2 depletion during breath-holds. However, voluntary submergence did result in slower pO2 depletion rates when compared to voluntary terrestrial apnoeas. The differences in whole body VO2 during breath-holds (measured at recovery) and venous pO2 (reflective of tissue O2-use measured during breath-holds), likely reflects metabolic suppression in hypoxic, vasoconstricted tissues. Consistent pCO2 values at the end of all voluntary breath-holds (59.0 ± 0.7 mmHg) suggests the physiological cue for stimulating respiration in northern elephant seal pups is the accumulation of CO2. Oxygen storage capacity and metabolic suppression directly limit diving capabilities and may influence foraging success in low-weaning weight seals forced to depart to sea prior to achieving full developmental diving capacity. PMID:24187422

The rotation axis for stationary and axisymmetric space-times

NASA Astrophysics Data System (ADS)

van den Bergh, N.; Wils, P.

1985-03-01

A set of 'extended' regularity conditions is discussed which have to be satisfied on the rotation axis if the latter is assumed to be also an axis of symmetry. For a wide class of energy-momentum tensors these conditions can only hold at the origin of the Weyl canonical coordinate. For static and cylindrically symmetric space-times the conditions can be derived from the regularity of the Riemann tetrad coefficients on the axis. For stationary space-times, however, the extended conditions do not necessarily hold, even when 'elementary flatness' is satisfied and when there are no curvature singularities on the axis. The result by Davies and Caplan (1971) for cylindrically symmetric stationary Einstein-Maxwell fields is generalized by proving that only Minkowski space-time and a particular magnetostatic solution possess a regular axis of rotation. Further, several sets of solutions for neutral and charged, rigidly and differentially rotating dust are discussed.

Proof of Concept to Isolate and Culture Primary Muscle Cells from Northern Elephant Seals to Study the Mechanisms that Maintain Aerobic Metabolism Under the Hypoxic Conditions of Breath-Hold Diving

DTIC Science & Technology

2014-09-30

that are too small have less effective results with mechanical trituration that follows digestion). 5. Move dish and sample into the cell culture...Cells from Northern Elephant Seals to Study the Mechanisms that Maintain Aerobic Metabolism Under the Hypoxic Conditions of Breath-Hold Diving...Muscle Cells from Northern Elephant Seals to Study the Mechanisms that Maintain Aerobic Metabolism Under the Hypoxic Conditions of Breath-Hold Diving 5a

Water holding capacities of fly ashes: Effect of size fractionation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sarkar, A.; Rano, R.

2007-07-01

Water holding capacities of fly ashes from different thermal power plants in Eastern India have been compared. Moreover, the effect of size fractionation (sieving) on the water holding capacities has also been determined. The desorption rate of water held by the fly ash fractions at ambient temperature (25-30{sup o}C) has been investigated. The effect of mixing various size fractions of fly ash in increasing the water holding capacities of fly ash has been studied. It is observed that the fly ash obtained from a thermal power plant working on stoker-fired combustor has the highest water holding capacity, followed by themore » one that works on pulverized fuel combustor. Fly ash collected from super thermal power plant has the least water holding capacity (40.7%). The coarser size fractions of fly ashes in general have higher water holding capacities than the finer ones. An attempt has been made to correlate the results obtained, with the potential use in agriculture.« less

Correlational analysis of electroencephalographic and end-tidal carbon dioxide signals during breath-hold exercise.

PubMed

Morelli, Maria Sole; Vanello, Nicola; Giannoni, Alberto; Frijia, Francesca; Hartwig, Valentina; Maestri, Michelangelo; Bonanni, Enrica; Carnicelli, Luca; Positano, Vincenzo; Passino, Claudio; Emdin, Michele; Landini, Luigi

2015-01-01

The central mechanism of breathing control is not totally understood. Several studies evaluated the correlation between electroencephalographic (EEG) power spectra and respiratory signals by performing resting state tasks or adopting hypercapnic/hypoxic stimuli. The observation of brain activity during voluntary breath hold tasks, might be an useful approach to highlight the areas involved in mechanism of breath regulation. Nevertheless, studies of brain activity with EEG could present some limitations due to presence of severe artifacts. When artifact rejection methods, as independent component analysis, cannot reliably clean EEG data, it is necessary to exclude noisy segments. In this study, global field power in the delta band and end-tidal CO2 were derived from EEG and CO2 signals respectively in 4 healthy subjects during a breath-hold task. The cross correlation function between the two signals was estimated taking into account the presence of missing samples. The statistical significance of the correlation coefficients at different time lags was assessed using surrogate data. Some simulations are introduced to evaluate the effect of missing data on the correlational analysis and their results are discussed. Results obtained on subjects show a significant correlation between changes in EEG power in the delta band and end-tidal CO2. Moreover, the changes in end-tidal CO2 were found to precede those of global field power. These results might help to better understand the cortical mechanisms involved in the control of breathing.

Nonequilibrium dynamic critical scaling of the quantum Ising chain.

PubMed

Kolodrubetz, Michael; Clark, Bryan K; Huse, David A

2012-07-06

We solve for the time-dependent finite-size scaling functions of the one-dimensional transverse-field Ising chain during a linear-in-time ramp of the field through the quantum critical point. We then simulate Mott-insulating bosons in a tilted potential, an experimentally studied system in the same equilibrium universality class, and demonstrate that universality holds for the dynamics as well. We find qualitatively athermal features of the scaling functions, such as negative spin correlations, and we show that they should be robustly observable within present cold atom experiments.

Tunnelling in Dante's Inferno

DOE Office of Scientific and Technical Information (OSTI.GOV)

Furuuchi, Kazuyuki; Sperling, Marcus, E-mail: kazuyuki.furuuchi@manipal.edu, E-mail: marcus.sperling@univie.ac.at

2017-05-01

We study quantum tunnelling in Dante's Inferno model of large field inflation. Such a tunnelling process, which will terminate inflation, becomes problematic if the tunnelling rate is rapid compared to the Hubble time scale at the time of inflation. Consequently, we constrain the parameter space of Dante's Inferno model by demanding a suppressed tunnelling rate during inflation. The constraints are derived and explicit numerical bounds are provided for representative examples. Our considerations are at the level of an effective field theory; hence, the presented constraints have to hold regardless of any UV completion.

Effect of Breast-Feeding and Maternal Holding in Relieving Painful Responses in Full-Term Neonates: A Randomized Clinical Trial.

PubMed

Obeidat, Hala M; Shuriquie, Mona A

2015-01-01

This randomized clinical trial was conducted to determine the efficacy of breast-feeding with maternal holding as compared with maternal holding without breast-feeding in relieving painful responses during heel lance blood drawing in full-term neonates. A convenience sample of 128 full-term newborn infants, in their fourth to sixth days of life, undergoing heel lance blood drawing for screening of hypothyroidism were included in the study. The neonates were randomly assigned into 2 equivalent groups. During heel lance blood drawing for infants, they either breast-fed with maternal holding (group I) or were held in their mother's lap without breast-feeding (group II). The painful responses were assessed simultaneously by 2 neonatal nurses blinded to the purpose of the study. Outcome measures for painful responses of the full-term neonates were evaluated with the Premature Infant Pain Profile scale. Independent t test showed significant differences in Premature Infant Pain Profile scale scores among the 2 groups (t = -8.447, P = .000). Pain scores were significantly lower among infants who were breast-fed in addition to maternal holding. Evidence from this study indicates that the combination of breast-feeding with maternal holding reduces painful responses of full-term infants during heel lance blood drawing.

32 CFR 199.14 - Provider reimbursement methods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... for neonatal services which has standardized costs that exceed a threshold of the greater of two times... CHAMPUS discharges in fiscal year 1988. (iv) Hold harmless provision. At such time as the weights... direct medical education costs. (x) Total full-time equivalents for: (A) Residents. (B) Interns. (xi...

32 CFR 199.14 - Provider reimbursement methods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... for neonatal services which has standardized costs that exceed a threshold of the greater of two times... CHAMPUS discharges in fiscal year 1988. (iv) Hold harmless provision. At such time as the weights... direct medical education costs. (x) Total full-time equivalents for: (A) Residents. (B) Interns. (xi...

78 FR 67201 - Sunshine Act Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-08

... LEGAL SERVICES CORPORATION Sunshine Act Meeting DATE AND TIME: The Legal Services Corporation's... disrupting the meeting, please refrain from placing the call on hold if doing so will trigger recorded music or other sound. From time to time, the presiding Chair may solicit comments from the public. STATUS...

78 FR 33114 - Sunshine Act Meetings

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-03

... LEGAL SERVICES CORPORATION Sunshine Act Meetings ACTION: Notice. Date And Time: The Legal Services... meeting, please refrain from placing the call on hold if doing so will trigger recorded music or other sound. From time to time, the Chair may solicit comments from the public. Status Of Meeting: Open...

Method and apparatus for gasifying with a fluidized bed gasifier having integrated pretreating facilities

DOEpatents

Rice, Louis F.

1981-01-01

An integral gasifier including a pretreater section and a gasifier section separated by a distribution grid is defined by a single vessel. The pretreater section pretreats coal or other carbon-containing material to be gasified to prevent caking and agglomeration of the coal in the gasifier. The level of the coal bed of the pretreater section and thus the holding or residence time in said bed is selectively regulated by the amount of pretreated coal which is lifted up a lift pipe into the gasifier section. Thus, the holding time in the pretreater section can be varied according to the amount of pretreat necessary for the particular coal to be gasified.

Time, Individualisation, and Ethics: Relating Vladimir Nabokov and Education

ERIC Educational Resources Information Center

Saeverot, Herner

2014-01-01

This article states that the concept of time we generally hold is a spatial version of time. However, a spatial time concept creates a series of problems, with unfortunate consequences for education.The problems become particularly obvious when the spatial time concept is used as a basis for the education function that is connected to the…

Holding back sharing concerns, dispositional emotional expressivity, perceived unsupportive responses and distress among women newly diagnosed with gynecological cancers.

PubMed

Manne, Sharon; Myers, Shannon; Ozga, Melissa; Kissane, David; Kashy, Debby; Rubin, Stephen; Heckman, Carolyn; Rosenblum, Norm

2014-01-01

Little attention has been paid to the role of holding back sharing concerns in the psychological adaptation of women newly diagnosed with gynecological cancers. The goal of the present study was to evaluate the role of holding back concerns in psychosocial adjustment and quality of life, as well as a possible moderating role for emotional expressivity and perceived unsupportive responses from family and friends. Two hundred forty-four women diagnosed with gynecological cancer in the past 8 months completed measures of holding back, dispositional emotional expressivity, perceived unsupportive responses from family and friends, cancer-specific distress, depressive symptoms and quality of life. Emotional expressivity moderated the association between holding back and cancer-specific distress and quality of life, but not depressive symptoms. Greater holding back was more strongly associated with higher levels of cancer-related distress among women who were more emotionally expressive than among women who were less expressive. Perceived unsupportive responses did not moderate the associations between holding back and psychosocial outcomes. Holding back sharing concerns was more common in this patient population than other cancer populations. Dispositional expressivity played a role in how harmful holding back concerns was for women, while unsupportive responses from family and friends did not. © 2014.

Development of Universal Portable Spray Stand for Touch-Up Process in The Automotive Paintshop

NASA Astrophysics Data System (ADS)

Fatah Muhamed Mukhtar, Muhamed Abdul; Mohideen Shahul Hameed, Rasool

2016-02-01

A spray stand is a custom-made tool used to hold the automotive body parts as well as the devices used to facilitate the operator during the Touch Up process in Paint shop production. This paper discusses about the development of Universal Portable Spray Stand (UPSS) as a tool to hold various types of automotive body parts and model of car during the painting process. The main objective of this study is to determine the effective application of UPSS at the International College of Automotive (ICAM) and also in the automotive industry. This will be helpful to add features to the current spray stand in ICAM and to add value to the spray stand based on selected criteria which are universal, portable and cost saving. In addition, study in the UPSS is also expected to bring reduction in cycle time during the touch up process, in the paint defects and in the ergonomics issues among the operators.

Predictors of transitions from single to multiple job holding: Results of a longitudinal study among employees aged 45-64 in the Netherlands.

PubMed

Bouwhuis, Stef; Geuskens, Goedele A; Boot, Cécile R L; Bongers, Paulien M; van der Beek, Allard J

2017-08-01

To construct prediction models for transitions to combination multiple job holding (MJH) (multiple jobs as an employee) and hybrid MJH (being an employee and self-employed), among employees aged 45-64. A total of 5187 employees in the Netherlands completed online questionnaires annually between 2010 and 2013. We applied logistic regression analyses with a backward elimination strategy to construct prediction models. Transitions to combination MJH and hybrid MJH were best predicted by a combination of factors including: demographics, health and mastery, work characteristics, work history, skills and knowledge, social factors, and financial factors. Not having a permanent contract and a poor household financial situation predicted both transitions. Some predictors only predicted combination MJH, e.g., working part-time, or hybrid MJH, e.g., work-home interference. A wide variety of factors predict combination MJH and/or hybrid MJH. The prediction model approach allowed for the identification of predictors that have not been previously studied. © 2017 Wiley Periodicals, Inc.

Prolonged dry apnoea: effects on brain activity and physiological functions in breath-hold divers and non-divers.

PubMed

Ratmanova, Patricia; Semenyuk, Roxana; Popov, Daniil; Kuznetsov, Sergey; Zelenkova, Irina; Napalkov, Dmitry; Vinogradova, Olga

2016-07-01

The aim of the study was to investigate the effects of voluntary breath-holding on brain activity and physiological functions. We hypothesised that prolonged apnoea would trigger cerebral hypoxia, resulting in a decrease of brain performance; and the apnoea's effects would be more pronounced in breath-hold divers. Trained breath-hold divers and non-divers performed maximal dry breath-holdings. Lung volume, alveolar partial pressures of O2 and CO2, attention and anxiety levels were estimated. Heart rate, blood pressure, arterial blood oxygenation, brain tissue oxygenation, EEG, and DC potential were monitored continuously during breath-holding. There were a few significant changes in electrical brain activity caused by prolonged apnoea. Brain tissue oxygenation index and DC potential were relatively stable up to the end of the apnoea in breath-hold divers and non-divers. We also did not observe any decrease of attention level or speed of processing immediately after breath-holding. Interestingly, trained breath-hold divers had some peculiarities in EEG activity at resting state (before any breath-holding): non-spindled, sharpened alpha rhythm; slowed-down alpha with the frequency nearer to the theta band; and untypical spatial pattern of alpha activity. Our findings contradicted the primary hypothesis. Apnoea up to 5 min does not lead to notable cerebral hypoxia or a decrease of brain performance in either breath-hold divers or non-divers. It seems to be the result of the compensatory mechanisms similar to the diving response aimed at centralising blood circulation and reducing peripheral O2 uptake. Adaptive changes during apnoea are much more prominent in trained breath-hold divers.

Output statistics of laser anemometers in sparsely seeded flows

NASA Technical Reports Server (NTRS)

Edwards, R. V.; Jensen, A. S.

1982-01-01

It is noted that until very recently, research on this topic concentrated on the particle arrival statistics and the influence of the optical parameters on them. Little attention has been paid to the influence of subsequent processing on the measurement statistics. There is also controversy over whether the effects of the particle statistics can be measured. It is shown here that some of the confusion derives from a lack of understanding of the experimental parameters that are to be controlled or known. A rigorous framework is presented for examining the measurement statistics of such systems. To provide examples, two problems are then addressed. The first has to do with a sample and hold processor, the second with what is called a saturable processor. The sample and hold processor converts the output to a continuous signal by holding the last reading until a new one is obtained. The saturable system is one where the maximum processable rate is arrived at by the dead time of some unit in the system. At high particle rates, the processed rate is determined through the dead time.

Are there two forms of isometric muscle action? Results of the experimental study support a distinction between a holding and a pushing isometric muscle function.

PubMed

Schaefer, Laura V; Bittmann, Frank N

2017-01-01

In isometric muscle function, there are subjectively two different modes of performance: one can either hold isometrically - thus resist an impacting force - or push isometrically - therefore work against a stable resistance. The purpose of this study is to investigate whether or not two different isometric muscle actions - the holding vs. pushing one (HIMA vs PIMA) - can be distinguished by objective parameters. Ten subjects performed two different measuring modes at 80% of MVC realized by a special pneumatic system. During HIMA the subject had to resist the defined impacting force of the pneumatic system in an isometric position, whereby the force of the cylinder works in direction of elbow flexion against the subject. During PIMA the subject worked isometrically in direction of elbow extension against a stable position of the system. The signals of pressure, force, acceleration and mechanomyography/-tendography (MMG/MTG) of the elbow extensor (MMGtri/MTGtri) and the abdominal muscle (MMGobl) were recorded and evaluated concerning the duration of maintaining the force level (force endurance) and the characteristics of MMG-/MTG-signals. Statistical group differences comparing HIMA vs. PIMA were estimated using SPSS. Significant differences between HIMA and PIMA were especially apparent regarding the force endurance: During HIMA the subjects showed a decisively shorter time of stable isometric position (19 ± 8 s) in comparison with PIMA (41 ± 24 s; p  = .005). In addition, during PIMA the longest isometric plateau amounted to 59.4% of the overall duration time of isometric measuring, during HIMA it lasted 31.6% ( p  = .000). The frequency of MMG/MTG did not show significant differences. The power in the frequency ranges of 8-15 Hz and 10-29 Hz was significantly higher in the MTGtri performing HIMA compared to PIMA (but not for the MMGs). The amplitude of MMG/MTG did not show any significant difference considering the whole measurement. However, looking only at the last 10% of duration time (exhaustion), the MMGtri showed significantly higher amplitudes during PIMA. The results suggest that under holding isometric conditions muscles exhaust earlier. That means that there are probably two forms of isometric muscle action. We hypothesize two potential reasons for faster yielding during HIMA: (1) earlier metabolic fatigue of the muscle fibers and (2) the complexity of neural control strategies.

Breath-holding ability of offshore workers inadequate to ensure escape from ditched helicopters.

PubMed

Cheung, S S; D'Eon, N J; Brooks, C J

2001-10-01

Following a helicopter ditching in water, the survival rate of individuals not mortally injured by the impact ranges from 50-85%. One possible cause for this low survival rate is that the crew and passengers cannot hold their breath underwater long enough to make the often difficult escape from an inverted and submerged helicopter. We investigated pulmonary function, breath-holding times in air (BHTa) and water (BHTw) of 228 students enrolled in offshore survival courses required to work in either the offshore petroleum industry or in military marine aviation. Comparisons were performed based on occupation, SCUBA experience, and smoking. In 25 degrees C pool water, the overall BHTw ranged from 5.4 to 120 s with a median of 37 s. Of the 228 subjects, 34% had a BHTw less than the 28 s required for the complete evacuation of a Super Puma helicopter under ideal conditions. No significant differences in BHTw were observed based on either smoking history (Non-Smoker, 41.5 +/- 21.6 s; Smoker, 37.2 +/- 20.2 s) or occupation (Novice, 37.5 +/- 21.1 s; Offshore, 40.5 +/- 21.1 s; Military, 45.2 +/- 20.9 s). However, SCUBA-trained individuals had a significantly longer BHT, (47.4 +/- 21.6 s) than non-SCUBA (37.6 +/- 20.6 s), as well as a greater force vital capacity (FVC), BHTa, and subjective comfort in water. It is concluded that the inability to breath-hold in emergency situations is a major contributor to the low survival rates of marine helicopter ditchings. Therefore, efforts must be made to both decrease escape times and to increase survival time underwater.

32 CFR 199.14 - Provider reimbursement methods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... services which has standardized costs that exceed a threshold of the greater of two times the DRG-based... fiscal year 1988. (iv) Hold harmless provision. At such time as the weights initially assigned to... direct medical education costs. (x) Total full-time equivalents for: (A) Residents. (B) Interns. (xi...

32 CFR 199.14 - Provider reimbursement methods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... services which has standardized costs that exceed a threshold of the greater of two times the DRG-based... fiscal year 1988. (iv) Hold harmless provision. At such time as the weights initially assigned to... direct medical education costs. (x) Total full-time equivalents for: (A) Residents. (B) Interns. (xi...

32 CFR 199.14 - Provider reimbursement methods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... services which has standardized costs that exceed a threshold of the greater of two times the DRG-based... fiscal year 1988. (iv) Hold harmless provision. At such time as the weights initially assigned to... direct medical education costs. (x) Total full-time equivalents for: (A) Residents. (B) Interns. (xi...

Particle-sampling statistics in laser anemometers Sample-and-hold systems and saturable systems

NASA Technical Reports Server (NTRS)

Edwards, R. V.; Jensen, A. S.

1983-01-01

The effect of the data-processing system on the particle statistics obtained with laser anemometry of flows containing suspended particles is examined. Attention is given to the sample and hold processor, a pseudo-analog device which retains the last measurement until a new measurement is made, followed by time-averaging of the data. The second system considered features a dead time, i.e., a saturable system with a significant reset time with storage in a data buffer. It is noted that the saturable system operates independent of the particle arrival rate. The probabilities of a particle arrival in a given time period are calculated for both processing systems. It is shown that the system outputs are dependent on the mean particle flow rate, the flow correlation time, and the flow statistics, indicating that the particle density affects both systems. The results are significant for instances of good correlation between the particle density and velocity, such as occurs near the edge of a jet.

Double-chamber electrode for spectrochemical determination of chlorine and other halogens

USGS Publications Warehouse

de Paiva, Azevedo; Specht, A.W.; Harner, R.S.

1954-01-01

A double-chamber, graphite electrode, suitable for d.c. arc determination of halogens by means of the alkaline earth halide bands, is described. An upper chamber holds the alkaline earth compound and an interconnected, lower chamber holds the halogen compound. This arrangement assures that there will be an abundance of alkaline earths in the arc by the time the halogen is volatilized from the lower chamber, and thereby promotes maximum emission of the alkaline earth halide bands. ?? 1954.

Results from flight and simulator studies of a Mach 3 cruise longitudinal autopilot

NASA Technical Reports Server (NTRS)

Gilyard, G. B.; Smith, J. W.

1978-01-01

At Mach numbers of approximately 3.0 and altitudes greater than 21,300 meters, the original altitude and Mach hold modes of the YF-12 autopilot produced aircraft excursions that were erratic or divergent, or both. Flight data analysis and simulator studies showed that the sensitivity of the static pressure port to angle of attack had a detrimental effect on the performance of the altitude and Mach hold modes. Good altitude hold performance was obtained when a high passed pitch rate feedback was added to compensate for angle of attack sensitivity and the altitude error and integral altitude gains were reduced. Good Mach hold performance was obtained when the angle of attack sensitivity was removed; however, the ride qualities remained poor.

Experimental study on the measurement of uranium casting enrichment by time-dependent coincidence method

NASA Astrophysics Data System (ADS)

Xie, Wen-Xiong; Li, Jian-Sheng; Gong, Jian; Zhu, Jian-Yu; Huang, Po

2013-10-01

Based on the time-dependent coincidence method, a preliminary experiment has been performed on uranium metal castings with similar quality (about 8-10 kg) and shape (hemispherical shell) in different enrichments using neutron from Cf fast fission chamber and timing DT accelerator. Groups of related parameters can be obtained by analyzing the features of time-dependent coincidence counts between source-detector and two detectors to characterize the fission signal. These parameters have high sensitivity to the enrichment, the sensitivity coefficient (defined as (ΔR/Δm)/R¯) can reach 19.3% per kg of 235U. We can distinguish uranium castings with different enrichments to hold nuclear weapon verification.

Breath-hold black-blood T1rho mapping improves liver T1rho quantification in healthy volunteers.

PubMed

Wáng, Yì Xiáng J; Deng, Min; Lo, Gladys G; Liang, Dong; Yuan, Jing; Chen, Weitian

2018-03-01

Background Recent researches suggest that T1rho may be a non-invasive and quantitative technique for detecting and grading liver fibrosis. Purpose To compare a multi-breath-hold bright-blood fast gradient echo (GRE) imaging and a single breath-hold single-shot fast spin echo (FSE) imaging with black-blood effect for liver parenchyma T1rho measurement and to study liver physiological T1rho value in healthy volunteers. Material and Methods The institutional Ethics Committee approved this study. 28 healthy participants (18 men, 10 women; age = 29.6 ± 5.1 years) underwent GRE liver T1rho imaging, and 20 healthy participants (10 men, 10 women; age = 36.9 ± 10.3 years) underwent novel black-blood FSE liver T1rho imaging, both at 3T with spin-lock frequency of 500 Hz. The FSE technique allows simultaneous acquisition of four spin lock times (TSLs; 1 ms, 10 ms, 30 ms, 50msec) in 10 s. Results For FSE technique the intra-scan repeatability intraclass correlation coefficient (ICC) was 0.98; while the inter-scan reproducibility ICC was 0.82 which is better than GRE technique's 0.76. Liver T1rho value in women tended to have a higher value than T1rho values in men (FSE: 42.28 ± 4.06 ms for women and 39.13 ± 2.12 ms for men; GRE: 44.44 ± 1.62 ms for women and 42.36 ± 2.00 ms for men) and FSE technique showed liver T1rho value decreased slightly as age increased. Conclusion Single breath-hold black-blood FSE sequence has better scan-rescan reproducibility than multi-breath-hold bright-blood GRE sequence. Gender and age dependence of liver T1rho in healthy participants is observed, with young women tending to have a higher T1rho measurement.

ADVANCEMENT OF THE RHIC BEAM ABORT KICKER SYSTEM.

DOE Office of Scientific and Technical Information (OSTI.GOV)

ZHANG,W.AHRENS,L.MI,J.OERTER,B.SANDBERG,J.WARBURTON,D.

2003-05-12

As one of the most critical system for RHIC operation, the beam abort kicker system has to be highly available, reliable, and stable for the entire operating range. Along with the RHIC commission and operation, consistent efforts have been spend to cope with immediate issues as well as inherited design issues. Major design changes have been implemented to achieve the higher operating voltage, longer high voltage hold-off time, fast retriggering and redundant triggering, and improved system protection, etc. Recent system test has demonstrated for the first time that both blue ring and yellow ring beam abort systems have achieved moremore » than 24 hours hold off time at desired operating voltage. In this paper, we report break down, thyratron reverse arcing, and to build a fast re-trigger system to reduce beam spreading in event of premature discharge.« less

Reducing the time rabbit sperm are held at 5 °C negatively affects their fertilizing ability after cryopreservation.

PubMed

Mocé, E; Blanch, E; Talaván, A; Viudes de Castro, M P

2014-10-15

Cooling sperm to and equilibrating the sperm at 5 °C require the most time in any sperm cryopreservation protocol. Reducing the time required for these phases would simplify sperm freezing protocols and allow greater number of ejaculates to be processed and frozen in a given time. This study determined how holding rabbit sperm at 5 °C for different lengths of time (0, 10, 15, 20, 30, or 45 minutes) affected the quality of rabbit sperm, measured by in vitro assays, and if reducing the cooling time to only 10 minutes affected the fertilizing ability of the sperm. Reducing the time sperm were held at 5 °C to 10 minutes did not affect the in vitro quality of the sperm (percent motile and with intact plasma membranes), although eliminating the cooling phase completely (directly freezing the sperm from room temperature) decreased in vitro assessed sperm quality (P<0.01). However, reducing the time sperm were held at 5 °C, from 45 to 10 minutes, negatively affected the fertilizing ability of sperm in vivo (P<0.05). In conclusion, completely eliminating cooling rabbit sperm to 5 °C before freezing is detrimental for rabbit sperm cryosurvival, and although shortening the time sperm are held at 5 °C to 10 minutes does not reduce in vitro sperm quality, it does reduce the fertility of rabbit sperm. Therefore, the length of time rabbit sperm equilibrate at 5 °C is crucial to the fertilizing ability of rabbit sperm and must be longer than 10 minutes. Currently, it is not known if holding rabbit sperm at 5 °C for less than 45 minutes will affect sperm fertilizing ability. Copyright © 2014 Elsevier Inc. All rights reserved.

Seminal plasma affects sperm sex sorting in boars.

PubMed

Alkmin, Diego V; Parrilla, Inmaculada; Tarantini, Tatiana; Del Olmo, David; Vazquez, Juan M; Martinez, Emilio A; Roca, Jordi

2016-04-01

Two experiments were conducted in boar semen samples to evaluate how both holding time (24h) and the presence of seminal plasma (SP) before sorting affect sperm sortability and the ability of sex-sorted spermatozoa to tolerate liquid storage. Whole ejaculate samples were divided into three aliquots immediately after collection: one was diluted (1:1, v/v) in Beltsville thawing solution (BTS; 50% SP); the SP of the other two aliquots was removed and the sperm pellets were diluted with BTS + 10% of their own SP (10% SP) or BTS alone (0% SP). The three aliquots of each ejaculate were divided into two portions, one that was processed immediately for sorting and a second that was sorted after 24h storage at 15-17°C. In the first experiment, the ability to exhibit well-defined X- and Y-chromosome-bearing sperm peaks (split) in the cytometry histogram and the subsequent sorting efficiency were assessed (20 ejaculates). In contrast with holding time, the SP proportion influenced the parameters examined, as evidenced by the higher number of ejaculates exhibiting split and better sorting efficiency (P<0.05) in semen samples with 0-10% SP compared with those with 50% SP. In a second experiment, the quality (viability, total and progressive motility) and functionality (plasma membrane fluidity and intracellular generation of reactive oxygen species) of sex-sorted spermatozoa were evaluated after 0, 72 and 120h storage at 15-17°C (10 ejaculates). Holding time and SP proportion did not influence the quality or functionality of stored sex-sorted spermatozoa. In conclusion, a holding time as long as 24h before sorting did not negatively affect sex sorting efficiency or the ability of sorted boar spermatozoa to tolerate long-term liquid storage. A high proportion of SP (50%) in the semen samples before sorting reduced the number of ejaculates to be sorted and negatively influenced the sorting efficiency, but did not affect the ability of sex-sorted spermatozoa to tolerate liquid storage.

Does smoking abstinence influence distress tolerance? An experimental study comparing the response to a breath-holding test of smokers under tobacco withdrawal and under nicotine replacement therapy.

PubMed

Cosci, Fiammetta; Anna Aldi, Giulia; Nardi, Antonio Egidio

2015-09-30

Distress tolerance has been operationalized as task persistence in stressful behavioral laboratory tasks. According to the distress tolerance perspective, how an individual responds to discomfort/distress predicts early smoking lapses. This theory seems weakly supported by experimental studies since they are limited in number, show inconsistent results, do not include control conditions. We tested the response to a stressful task in smokers under abstinence and under no abstinence to verify if tobacco abstinence reduces task persistence, thus distress tolerance. A placebo-controlled, double-blind, randomized, cross-over design was used. Twenty smokers underwent a breath holding test after the administration of nicotine on one test day and a placebo on another test day. Physiological and psychological variables were assessed at baseline and directly before and after each challenge. Abstinence induced a statistically significant shorter breath holding duration relative to the nicotine condition. No different response to the breath holding test was observed when nicotine and placebo conditions were compared. No response to the breath holding test was found when pre- and post-test values of heart rate, blood pressure, Visual Analogue Scale for fear or discomfort were compared. In brief, tobacco abstinence reduces breath holding duration but breath holding test does not influence discomfort. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Thermal scanner data for studying freeze conditions and for aiding irrigation scheduling

NASA Technical Reports Server (NTRS)

Bartholic, J. F.; Wiegand, C. L.; Leamer, R. W.; Namken, L. N.

1970-01-01

The use of thermal imagery in connection with plant water stress appears to hold considerable potential, particularly with scanners such as the RS-14 where internal calibration sources can be adjusted to bracket the temperatures of interest. The data from the thermal film are fairly easy to reduce; however, data reduction in 3 days or less would be required before it could be used in irrigation timing.

Evaluation of nonpoint-source contamination, Wisconsin; selected streamwater-quality data, land-use and best-management practices inventory, and quality assurance and quality control, water year 1993

USGS Publications Warehouse

Corsi, Steven R.; Walker, John F.; Graczyk, D.J.; Greb, S.R.; Owens, D.W.; Rappold, K.F.

1995-01-01

A special study was done to determine the effect of holding time on fecal coliform colony counts. A linear regression indicated that the mean decrease in colony counts over 72 hours was 8.2 percent per day. Results after 24 hours showed that colony counts increased in some samples and decreased in others.

Effect of the federal estate tax on nonindustrial private forest holdings

Treesearch

John L. Greene; Steven H. Bullard; Tamara L. Cushing; Theodore Beauvais

2006-01-01

Data for this study were collected using a questionnaire mailed to randomly selected members of two forest owner organizations. Among the key findings is that 38% of forest estates owed federal estate tax, a rate many times higher than US estates in general. In 28% of the cases where estate tax was due, timber or land was sold because other assets were not adequate. In...

TGI Monday?: drug-dependent outpatients report lower stress and more happiness at work than elsewhere.

PubMed

Epstein, David H; Preston, Kenzie L

2012-01-01

In the general population, experience-sampling studies show that work is the aspect of daily life most associated with momentary unhappiness and a desire to be elsewhere. We assessed whether this holds true for urban outpatients in treatment for heroin and cocaine dependence. In a 25-week natural-history study, 79 employed methadone-maintained misusers of heroin and cocaine carried electronic diaries on which mood and behavior were assessed up to five times per day. Being at work was associated with lower stress, greater happiness, and lower drug craving. Work accounted for 14% of the variance in stress, 30% of the variance in happiness, and 50% of the variance in cocaine craving. Participants with skilled jobs reported more positive and less negative mood states (and lower cocaine craving) at all times compared to participants with semi/unskilled jobs, although the latter reported greater mood improvement at work. In all participants, mood improvements occurred specifically in the presence of coworkers (not other companions). Our seemingly unusual findings might be specific to substance-disorder patients (for whom work may be a respite from drug-using companions), but might also hold for other urban dwellers of similar socioeconomic backgrounds (for whom work may be a respite from environmental stressors). Copyright © American Academy of Addiction Psychiatry.

TGI Monday?: Drug-Dependent Outpatients Report Lower Stress and More Happiness at Work than Elsewhere

PubMed Central

Epstein, David H.; Preston, Kenzie L.

2013-01-01

In the general population, experience-sampling studies show that work is the aspect of daily life most associated with momentary unhappiness and a desire to be elsewhere. We assessed whether this holds true for urban outpatients in treatment for heroin and cocaine dependence. In a 25-week natural-history study, 79 employed methadone-maintained misusers of heroin and cocaine carried electronic diaries on which mood and behavior were assessed up to five times per day. Being at work was associated with lower stress, greater happiness, and lower drug craving. Work accounted for 14% of the variance in stress, 30% of the variance in happiness, and 50% of the variance in cocaine craving. Participants with skilled jobs reported more positive and less negative mood states (and lower cocaine craving) at all times compared to participants with semi/unskilled jobs, although the latter reported greater mood improvement at work. In all participants, mood improvements occurred specifically in the presence of coworkers (not other companions). Our seemingly unusual findings might be specific to substance-disorder patients (for whom work may be a respite from drug-using companions), but might also hold for other urban dwellers of similar socioeconomic backgrounds (for whom work may be a respite from environmental stressors). PMID:22494220

Patent holdings of US biotherapeutic companies in major markets.

PubMed

Sebastian, Teena E; Yerram, Chandra Bindu; Saberwal, Gayatri

2009-05-01

In previous studies we examined the (United States, US) patent holdings of 109 largely North American biotech companies developing therapeutics that, in particular, have an interest in discovery stage science. There appears little correlation between the number of patents and the number of products of individual companies. Here we quantified and compared the 103 US-headquartered companies' patent holdings in Australia, Canada, Europe, Japan and the US. The companies demonstrate variable and surprising patterns of patent holdings across these countries or regions. For most companies, patent holdings are not in proportion to the importance of the country as a biotech or pharma market. These results have implications for the patenting strategies of small biotech companies involved in drug discovery.

Parents' presence and parent-infant closeness in 11 neonatal intensive care units in six European countries vary between and within the countries.

PubMed

Raiskila, Simo; Axelin, Anna; Toome, Liis; Caballero, Sylvia; Tandberg, Bente Silnes; Montirosso, Rosario; Normann, Erik; Hallberg, Boubou; Westrup, Björn; Ewald, Uwe; Lehtonen, Liisa

2017-06-01

Little is known about the amount of physical parent-infant closeness in neonatal intensive care units (NICUs), and this study explored that issue in six European countries. The parents of 328 preterm infants were recruited in 11 NICUs in Finland, Estonia, Sweden, Norway, Italy and Spain. They filled in daily diaries about how much time they spent in the NICU, in skin-to-skin contact (SSC) and holding their babies in the first two weeks of their hospitalisation. The parents' NICU presence varied from a median of 3.3 (minimum 0.7-maximum 6.7) to 22.3 (18.7-24.0) hours per day (p < 0.001), SSC varied from 0.3 (0-1.4) to 6.6 (2.2-19.5) hours per day (p < 0.001) and holding varied from 0 (0-1.5) to 3.2 (0-7.4) hours per day (p < 0.001). Longer SSC was associated with singleton babies and more highly educated mothers. Holding the baby for longer was associated with gestational age. The most important factor supporting parent-infant closeness was the opportunity to stay overnight in the NICU. Having other children and the distance from home to the hospital had no impact on parent-infant closeness. Parents spent more time in NICUs if they could stay overnight, underlining the importance that these facilities play in establishing parent-infant closeness. ©2017 The Authors. Acta Paediatrica published by John Wiley & Sons Ltd on behalf of Foundation Acta Paediatrica.

Effect of high-pressure processing on quality and stability of green mango blended mayonnaise.

PubMed

Sethi, Swati; Chauhan, O P; Anurag, Rahul K

2017-07-01

The present work was aimed to study and optimize the high pressure treated green mango blended mayonnaise in terms of oxidative and emulsion stability, as a function of technical parameters; pressure intensity, dwell period and level of green mango pulp. Mayonnaise samples were treated at different combinations of pressure (400-600 MPa), holding time (5-10 min) and level of green mango pulp (10-30%) following Box-Behnken design. Mayonnaise quality was evaluated in terms of oxidative stability and emulsion stability using response surface methodology to optimize the best possible combination among all. Analysis of variance showed that the second-order polynomial model fitted well with the experimental results. Pressure and time were the most important factors determining the oxidative stability (free fatty acids, peroxide value and anisidine value) whereas; the emulsion stability (creaming and thermal creaming) was most significantly affected by the level of green mango pulp. The optimized conditions for preparing green mango blended mayonnaise with high oxidative and emulsion stability were: 435 MPa pressure, 5 min of holding time with the addition of green mango pulp at the rate of 28%. The product prepared at optimum conditions showed good correlations between predicted and actual values.

Gear distortion analysis due to heat treatment process

NASA Astrophysics Data System (ADS)

Guterres, Natalino F. D. S.; Rusnaldy, Widodo, Achmad

2017-01-01

One way to extend the life time of the gear is minimizing the distortion during the manufacturing process. One of the most important processes in manufacturing to produce gears is heat treatment process. The purpose of this study is to analyze the distortion of the gear after heat treatment process. The material of gear is AISI 1045, and it was designed with the module (m) 1.75, and a number of teeth (z) 29. Gear was heat-treated in the furnace at a temperature of 800°C, holding time of 30 minutes, and then quenched in water. Furthermore, surface hardening process was also performed on gear teeth at a temperature of 820°C and holding time of 35 seconds and the similar procedure of analysis was conducted. The hardness of gear after heat treatment average 63.2 HRC and the teeth surface hardness after gear to induction hardening was 64.9 HRC at the case depth 1 mm. The microstructure of tested gear are martensitic and pearlite. The highest distortion on tooth thickness to upper than 0.063 can cause high precision at the tooth contact is not appropriate. Besides the shrinkage of tooth thickness will also affect to contact angle because the size of gear tolerance was not standardized.

Synthesis and Compatibility of Ionic Liquid Containing Rod-Coil Polyimide Gel Electrolytes with Lithium Metal Electrodes

NASA Technical Reports Server (NTRS)

Tigelaar, Dean M.; Palker, Allyson E.; Meador, Mary Ann B.; Bennett, William R.

2008-01-01

A highly cross-linked polyimide-polyethylene oxide copolymer has been synthesized that is capable of holding large volumes of liquid component, simultaneously maintaining good dimensional stability. An amine end capped oligomer was made that was imidized in solution, followed by reaction with a triisocyanate in the presence of desired additives at ambient temperature. Polymer films are able to hold over 4 times their weight in room temperature ionic liquid RTIL or carbonate solvent. Electrolytes were studied that contained varying amounts of RTIL, lithium trifluoromethanesulfonimide LiTFSi, and alumina nanoparticles. Electrochemical stability of these electrolytes with lithium metal electrodes was studied by galvanic cycling and impedance spectroscopy. Improved cycling stability and decreased interfacial resistance were observed when increasing amounts of RTIL and LiTFSi were added. The addition of small amounts of alumina further decreased interfacial resistance by nearly an order of magnitude. During the course of the study, cycling stability increased from less than 3 to greater than 1000 h at 60 C and 0.25 mA/cm2 current density.

Paced respiration with end-expiration technique offers superior BOLD signal repeatability for breath-hold studies.

PubMed

Scouten, A; Schwarzbauer, C

2008-11-01

As a simple, non-invasive method of blood oxygenation level-dependent (BOLD) signal calibration, the breath-hold task offers considerable potential for the quantification of neuronal activity from functional magnetic resonance imaging (fMRI) measurements. With an aim to improve the precision of this calibration method, the impact of respiratory rate control on the BOLD signal achieved with the breath-hold task was investigated. In addition to self-paced breathing, three different computer-paced breathing rates were imposed during the periods between end-expiration breath-hold blocks. The resulting BOLD signal timecourses and statistical activation maps were compared in eleven healthy human subjects. Results indicate that computer-paced respiration produces a larger peak BOLD signal increase with breath-hold than self-paced breathing, in addition to lower variability between trials. This is due to the more significant post-breath-hold signal undershoot present in self-paced runs, a characteristic which confounds the definition of baseline and is difficult to accurately model. Interestingly, the specific respiratory rate imposed between breath-hold periods generally does not have a statistically significant impact on the BOLD signal change. This result can be explained by previous reports of humans adjusting their inhalation depth to compensate for changes in rate, with the end-goal of maintaining homeostatic ventilation. The advantage of using end-expiration relative to end-inspiration breath-hold is apparent in view of the high repeatability of the BOLD signal in the present study, which does not suffer from the previously reported high variability associated with uncontrolled inspiration depth when using the end-inspiration technique.

Effects of ipsilateral anterior thigh soft tissue stretching on passive unilateral straight-leg raise.

PubMed

Clark, S; Christiansen, A; Hellman, D F; Hugunin, J W; Hurst, K M

1999-01-01

Randomized 3-group pretest-posttest with blind assessment of outcome. The purpose of this study was to examine the effect of sagittal plane hold-relax exercise applied to the ipsilateral anterior thigh, and prone positioning on passive unilateral straight-leg raise measurements. Straight-leg raising has been viewed as a measurement for hamstring muscle length, but literature suggests that other structures may affect this measurement. Sixty subjects (45 men, 15 women) qualified for inclusion into the study based on a straight-leg raise measurement of < or = 65 degrees. Subjects were randomly assigned to one of three groups: control, static stretch, or sagittal plane hold-relax exercise. Pretest and posttest straight-leg raise measurements of the right lower extremity were performed for each subject. A 1-way ANOVA of the change scores showed a significant difference between groups. A Tukey post hoc analysis of the change scores showed that both treatment groups' means differed significantly from the control group and from each other, with the sagittal plane hold-relax group exhibiting the largest change (mean of 7.8 degrees +/- 2.8 degrees). The results of this study show that sagittal plane hold-relax exercise and passive prone results of this study show that sagittal plane hold-relax and passive prone positioning can significantly increase straight-leg raise range of motion, however the sagittal plane hold-relax stretching of the anterior thigh is more effective than passive prone positioning.

Relations between DNA- and RNA-based molecular methods for cyanobacteria and microcystin concentration at Maumee Bay State Park Lakeside Beach, Oregon, Ohio, 2012

USGS Publications Warehouse

Stelzer, Erin A.; Loftin, Keith A.; Struffolino, Pamela

2013-01-01

Water samples were collected from Maumee Bay State Park Lakeside Beach, Oregon, Ohio, during the 2012 recreational season and analyzed for selected cyanobacteria gene sequences by DNA-based quantitative polymerase chain reaction (qPCR) and RNA-based quantitative reverse-transcription polymerase chain reaction (qRT-PCR). Results from the four DNA assays (for quantifying total cyanobacteria, total Microcystis, and Microcystis and Planktothrix strains that possess the microcystin synthetase E (mcyE) gene) and two RNA assays (for quantifying Microcystis and Planktothrix genera that are expressing the microcystin synthetase E (mcyE) gene) were compared to microcystin concentration results determined by an enzyme-linked immunosorbent assay (ELISA). Concentrations of the target in replicate analyses were log10 transformed. The average value of differences in log10 concentrations for the replicates that had at least one detection were found to range from 0.05 to >0.37 copy per 100 milliliters (copy/100 mL) for DNA-based methods and from >0.04 to >0.17 copy/100 mL for RNA-based methods. RNA has a shorter half-life than DNA; consequently, a 24-hour holding-time study was done to determine the effects of holding time on RNA concentrations. Holding-time comparisons for the RNA-based Microcystis toxin mcyE assay showed reductions in the number of copies per 100 milliliters over 24 hours. The log difference between time 2 hours and time 24 hours was >0.37 copy/100 mL, which was higher than the analytical variability (log difference of >0.17 copy/100 mL). Spearman’s correlation analysis indicated that microcystin toxin concentrations were moderately to highly related to DNA-based assay results for total cyanobacteria (rho=0.69), total Microcystis (rho=0.74), and Microcystis strains that possess the mcyE gene (rho=0.81). Microcystin toxin concentrations were strongly related with RNA-based assay results for Microcystis mcyE gene expression (rho=0.95). Correlation analysis could not be done for Planktothrix mcyE gene expression because of too few detections.

Nonuniform Effects of Reinstatement within the Time Window

ERIC Educational Resources Information Center

Galluccio, Llissa; Rovee-Collier, Carolyn

2006-01-01

A time window is a limited period after an event initially occurs in which additional information can be integrated with the memory of that event. It shuts when the memory is forgotten. The time window hypothesis holds that the impact of a manipulation at different points within the time window is nonuniform. In two operant conditioning…

On the optimal use of a slow server in two-stage queueing systems

NASA Astrophysics Data System (ADS)

Papachristos, Ioannis; Pandelis, Dimitrios G.

2017-07-01

We consider two-stage tandem queueing systems with a dedicated server in each queue and a slower flexible server that can attend both queues. We assume Poisson arrivals and exponential service times, and linear holding costs for jobs present in the system. We study the optimal dynamic assignment of servers to jobs assuming that two servers cannot collaborate to work on the same job and preemptions are not allowed. We formulate the problem as a Markov decision process and derive properties of the optimal allocation for the dedicated (fast) servers. Specifically, we show that the one downstream should not idle, and the same is true for the one upstream when holding costs are larger there. The optimal allocation of the slow server is investigated through extensive numerical experiments that lead to conjectures on the structure of the optimal policy.

Comparison of Enzymatic and Ultrasonic Extraction of Albumin from Defatted Pumpkin (Cucurbita pepo)
Seed Powder

PubMed Central

Tu, Gia Loi; Bui, Thi Hoang Nga; Tran, Thi Thu Tra; Ton, Nu Minh Nguyet

2015-01-01

Summary In this study, ultrasound- and enzyme-assisted extractions of albumin (water-soluble protein group) from defatted pumpkin (Cucurbita pepo) seed powder were compared. Both advanced extraction techniques strongly increased the albumin yield in comparison with conventional extraction. The extraction rate was two times faster in the ultrasonic extraction than in the enzymatic extraction. However, the maximum albumin yield was 16% higher when using enzymatic extraction. Functional properties of the pumpkin seed albumin concentrates obtained using the enzymatic, ultrasonic and conventional methods were then evaluated. Use of hydrolase for degradation of cell wall of the plant material did not change the functional properties of the albumin concentrate in comparison with the conventional extraction. The ultrasonic extraction enhanced water-holding, oil-holding and emulsifying capacities of the pumpkin seed albumin concentrate, but slightly reduced the foaming capacity, and emulsion and foam stability. PMID:27904383

Comparison of Enzymatic and Ultrasonic Extraction of Albumin from Defatted Pumpkin (Cucurbita pepo)
Seed Powder.

PubMed

Tu, Gia Loi; Bui, Thi Hoang Nga; Tran, Thi Thu Tra; Ton, Nu Minh Nguyet; Man Le, Van Viet

2015-12-01

In this study, ultrasound- and enzyme-assisted extractions of albumin (water-soluble protein group) from defatted pumpkin ( Cucurbita pepo ) seed powder were compared. Both advanced extraction techniques strongly increased the albumin yield in comparison with conventional extraction. The extraction rate was two times faster in the ultrasonic extraction than in the enzymatic extraction. However, the maximum albumin yield was 16% higher when using enzymatic extraction. Functional properties of the pumpkin seed albumin concentrates obtained using the enzymatic, ultrasonic and conventional methods were then evaluated. Use of hydrolase for degradation of cell wall of the plant material did not change the functional properties of the albumin concentrate in comparison with the conventional extraction. The ultrasonic extraction enhanced water-holding, oil-holding and emulsifying capacities of the pumpkin seed albumin concentrate, but slightly reduced the foaming capacity, and emulsion and foam stability.

Mechanics of airway and alveolar collapse in human breath-hold diving.

PubMed

Fitz-Clarke, John R

2007-11-15

A computational model of the human respiratory tract was developed to study airway and alveolar compression and re-expansion during deep breath-hold dives. The model incorporates the chest wall, supraglottic airway, trachea, branched airway tree, and elastic alveoli assigned time-dependent surfactant properties. Total lung collapse with degassing of all alveoli is predicted to occur around 235 m, much deeper than estimates for aquatic mammals. Hysteresis of the pressure-volume loop increases with maximum diving depth due to progressive alveolar collapse. Reopening of alveoli occurs stochastically as airway pressure overcomes adhesive and compressive forces on ascent. Surface area for gas exchange vanishes at collapse depth, implying that the risk of decompression sickness should reach a plateau beyond this depth. Pulmonary capillary transmural stresses cannot increase after local alveolar collapse. Consolidation of lung parenchyma might provide protection from capillary injury or leakage caused by vascular engorgement due to outward chest wall recoil at extreme depths.

[Ballistocardiographic studies during the 4th expedition on the Saliut-6 orbital station].

PubMed

Baevskiĭ, R M; Funtova, I I

1982-01-01

This paper presents ballistocardiographic examinations of the Salyut-6 fourth expedition crew members who showed variations in both the shape and the amplitude of ballistocardiographic complexes. Ballistocardiograms (BCG) were recorded by means of a piezoelectric sensor with a sensitivity of 3 mV/cm x s-2. The sensor weight was 30 g. The sensor was attached to the upper part of the iliac bone, near the body mass center. During ballistocardiography the ballistic forces in the head-to-feet direction were recorded. The examinations were performed preflight and on mission days 46, 71, 98, 133, and 175. Hemodynamic specificities of the right and left heart were determined with the aid of the breath holding test. Measurements of BCG amplitudes were used to determine the kinetic effect of heart rate. The largest amplitude of BCG waves was seen on mission day 133. At this time period the systolic wave amplitude decreased during inhalation holding.

A Randomized Double-Blinded Trial on the Effects of Ultrasound Transducer Orientation on Teaching and Learning Ultrasound-Guided Regional Anesthesia.

PubMed

Lam, Nicholas C K; Baker, Elizabeth B; Fishburn, Steven J; Hammer, Angie R; Petersen, Timothy R; Mariano, Edward R

2016-07-01

Learning ultrasound-guided regional anesthesia skills, especially needle/ beam alignment, can be especially difficulty for trainees, who can often become frustrated. We hypothesized that teaching novices to orient the transducer and needle perpendicular to their shoulders will improve performance on a standardized task, compared to holding the transducer and needle parallel to the shoulders. This study compared the effects of transducer orientation on trainees' ability to complete a standardized ultrasound-guided nerve block simulation. The time to task completion and percentage of the attempt time without adequate needle visualization were measured. Participants were right-handed healthy adults with no previous ultrasound experience and were randomly assigned to training in either transducer and needle alignment in a coronal plane, parallel to the shoulders (parallel group) or transducer and needle alignment in a sagittal plane, perpendicular to the shoulders (perpendicular group). Participants used ultrasound to direct a needle to 3 targets in a standardized gelatin phantom and repeated this task 3 times. Their efforts were timed and evaluated by an assessor, who was blinded to group assignment. Data were analyzed on 28 participants. The perpendicular group was able to complete the task more quickly (P < .001) and with a smaller proportion of time lost to inadequate needle visualization (P < .001). Ultrasound-guided regional anesthesia trainees complete a standardized task more quickly and efficiently when instructed to hold the transducer and needle in an orientation perpendicular to their shoulders.

THE EFFICACY OF AN EIGHT-WEEK CORE STABILIZATION PROGRAM ON CORE MUSCLE FUNCTION AND ENDURANCE: A RANDOMIZED TRIAL

PubMed Central

Sperier, Aubrey D.; Hopkins, Colleen F.; Griffiths, Bridgette D.; Principe, Molly F.; Schnall, Barri L.; Bell, Johanna C.; Koppenhaver, Shane L.

2016-01-01

ABSTRACT Background Body armor is credited with increased survival rates in soldiers but the additional axial load may negatively impact the biomechanics of the spine resulting in low back pain. Multiple studies have found that lumbar stabilization programs are superior to generalized programs for patients with chronic low back pain. It is not known if such programs produce objective changes in trunk muscle function with wear of body armor. Hypothesis/Purpose An eight-week core stability exercise program would result in a larger improvement in physical endurance and abdominal muscle thickness than a control intervention. The purpose of this study was to assess the effectiveness of an eight-week core stability exercise program on physical endurance and abdominal muscle thickness with and without wear of body armor. Study Design Randomized controlled trial Methods Participants (N = 33) were randomized into either the core strengthening exercise group or the control group. Testing included ultrasound imaging of abdominal muscle thickness in hook-lying and standing with and without body armor and timed measures of endurance. Results There were statistically significant group by time interactions for transversus abdominis muscle contraction thickness during standing, both with (p = 0.018) and without body armor (p = 0.038). The main effect for hold-time during the horizontal side-support (p = 0.016) indicated improvement over time regardless of group. There was a significant group by time interaction (p = 0.014) for horizontal side-support hold-time when compliance with the exercise protocol was set at 85%, indicating more improvement in the core stabilization group than in the control group. Conclusion Performing an eight-week core stabilization exercise program significantly improves transversus abdominis muscle activation in standing and standing with body armor. When compliant with the exercises, such a program may increase trunk strength and muscle endurance. Levels of Evidence Therapy, Level 2b PMID:27525175

Noninvasive Measurement of Steroid Hormones in Zebrafish Holding-Water

PubMed Central

Félix, Ana S.; Faustino, Ana I.; Cabral, Eduarda M.

2013-01-01

Abstract Zebrafish (Danio rerio) has recently emerged as a new animal model in neuroendocrinology and behavior (e.g., stress physiology and ecotoxicology studies). In these areas, the concentrations of steroid hormones in the blood are often used to study the endocrinological status of individuals. However, due to the small body size of zebrafish, blood sampling is difficult to perform and the amount of plasma obtained per sample for assaying hormones is very small (ca. 1–5 μL), and therefore most studies have been using whole-body hormone concentrations, which implies sacrificing the individuals and hampers sequential sampling of the same individual. Here a noninvasive method to assay steroid hormones from zebrafish holding-water, based on the fact that steroids are released into the fish holding-water through the gills by passive diffusion, is validated. Cortisol and the androgen 11-ketotestosterone (KT) were measured in water samples and compared to plasma levels in the same individuals. Cortisol released to holding-water correlates positively with plasma concentrations, but there was a lack of correlation between KT water and circulating levels. However, KT levels showed a highly significant sex difference that can be used to noninvasively sex individuals. An ACTH challenge test demonstrated that an induced increase in circulating cortisol concentration can be reliably detected in holding-water levels, hence attesting the responsiveness of holding-water levels to fluctuations in circulating levels. PMID:23445429

Technologies for decreasing the tap temperature to save energy in steel foundries

NASA Astrophysics Data System (ADS)

Biswas, Siddhartha

Steel foundries are one of the most energy intensive industries. The increasing concerns over volatile energy cost and carbon dioxide emission have pushed foundries to improve efficiency and hence decrease electrical energy consumption. Statistical analysis of industrial survey data was combined with computational fluid dynamics (CFD) modeling to investigate the best industrial practices and opportunities to improve energy efficiency. Reducing tap temperature was identified as one of the important ways of reducing energy consumption. Steel foundries typically tap at 1650-1800°C (3000-3300°F) which is 100-250°C (150-450°F) higher than the pouring temperature. The steel temperature is elevated to compensate for the temperature loss associated with tapping, holding and transporting the liquid steel from the furnace to the pouring floor. Based on experimental investigations and CFD modeling of heat losses during holding in the ladle for different foundry practices, a spreadsheet calculator has been developed to calculate the optimum tap temperature for the specific foundry practices which will eliminate unnecessary superheating. The calculated results were compared and validated with industrial measurements. Improving the lining refractory is one significant way of reducing heat losses during holding of the steel in ladle. Silica sand linings are being used in steel foundries as an inexpensive and convenient material for short holding times and small volumes. The possibilities of improvements of silica sand linings by the addition of lower density cenospheres (hollow spheres), a byproduct of coal fired power plants, was studied through property measurements and laboratory trials.

Opportunities of energy supply of farm holdings on the basis of small-scale renewable energy sources

NASA Astrophysics Data System (ADS)

Efendiev, A. M.; Nikolaev, Yu. E.; Evstaf'ev, D. P.

2016-02-01

One of the major national economic problems of Russia is raising of agricultural production, which will provide strategic security and sustainable supply of the population with provisions. Creation of subsidiary small holdings, farm holdings, and peasant farm holdings will require addressing issues of energy supply. At considerable distance of small farms from centralized energy systems (by fuel, electricity and thermal energy) it is proposed to create a system of local energy networks on the basis of low-powered power plants using renewable energy sources (RES). There is economic unreasonableness of use of imported components of small power plants. Creation of new combined small power plants on renewable energy sources produced by domestic manufacturers is recommended. Schemes of arrangements of small power plants based on renewable energy sources are proposed, variants and characteristics of a basic source are provided—biogas plants developed by the authors. Calculations revealed that heat and power supply of self-contained farms distant from small power plants based on renewable energy sources is 2.5-2.6 times cheaper than from centralized networks. Production of biogas through anaerobic fermentation of organic waste of cattle complexes is considered as the basis. The analysis of biowaste output in various cattle farms is carried out, and the volume of biogas is determined to meet the requirements of these farms in electrical and thermal energy. The objective of the present article is to study the possibility of creating small combined power plants in Russia based on renewable sources of energy for independent consumers.

A study for testing the Kerr metric with AGN iron line eclipses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cárdenas-Avendaño, Alejandro; Jiang, Jiachen; Bambi, Cosimo, E-mail: alejandro.cardenasa@konradlorenz.edu.co, E-mail: jcjiang12@fudan.edu.cn, E-mail: bambi@fudan.edu.cn

2016-04-01

Recently, two of us have studied iron line reverberation mapping to test black hole candidates, showing that the time information in reverberation mapping can better constrain the Kerr metric than the time-integrated approach. Motivated by this finding, here we explore the constraining power of another time-dependent measurement: an AGN iron line eclipse. An obscuring cloud passes between the AGN and the distant observer, covering different parts of the accretion disk at different times. Similar to the reverberation measurement, an eclipse might help to better identify the relativistic effects affecting the X-ray photons. However, this is not what we find. Inmore » our study, we employ the Johannsen-Psaltis parametrisation, but we argue that our conclusions hold in a large class of non-Kerr metrics. We explain our results pointing out an important difference between reverberation and eclipse measurements.« less

Effects of Exposure to Gun Violence in Movies on Children's Interest in Real Guns.

PubMed

Dillon, Kelly P; Bushman, Brad J

2017-11-01

More US children die by accidental gun use than children in other developed countries. One factor that can influence children's interest in guns is exposure to media containing guns. To test whether children who see a movie containing guns will handle a real gun longer and will pull the trigger more times than children who see the same movie not containing guns. One hundred four children aged 8 to 12 years recruited through advertisements were randomly assigned in pairs to watch a 20-minute PG-rated movie containing or not containing guns in a university laboratory. Children then played with toys and games in a room for 20 minutes while being video recorded. A cabinet in the room contained a real (disabled) gun with a sensor counting trigger pulls. Recordings were coded for the time spent holding the gun and in aggressive play. Data were collected from July 15, 2015, through January 1, 2016, and analyzed using generalized estimating equations (Tweedie log-link for time spent holding the gun; Poisson log-link for pulling the trigger). The 2 main outcomes were time spent holding the gun and the number of trigger pulls. Control variables included sex, age, trait aggressiveness, exposure to violent media, interest in guns, and number of guns at home. Among the 104 study participants (62 boys [59.6%] and 42 girls [40.4%]; mean (SD) age, 9.9 [1.5] years), the adjusted median number of trigger pulls among children who saw the movie containing guns was 2.8 (interquartile range [IQR], 0.2-2.8) compared with 0.01 (IQR, 0.01-0.2) among children who saw the movie not containing guns (adjusted odds ratio, 22.3; 95% CI, 6.0-83.4; P < .001). The adjusted median number of seconds spent holding the gun among children who saw a movie containing guns was 53.1 (IQR, 35.5-53.1) compared with 11.1 (IQR, 10.7-16.7) among children who saw the movie not containing guns (adjusted odds ratio, 3.0; 95% CI, 0.9-9.9; P = .07). Qualitative analyses on 4 pairs from each condition found that children who saw the movie containing guns also played more aggressively and sometimes fired the gun at people (ie, self, partner, or passersby on street). Children in the United States frequently have access to unsecured firearms and frequently consume media containing guns. This experiment shows that children who see movie characters use guns are more likely to use guns themselves. clinicaltrials.gov Identifier NCT03220412.

Creep-Fatigue Damage Investigation and Modeling of Alloy 617 at High Temperatures

NASA Astrophysics Data System (ADS)

Tahir, Fraaz

The Very High Temperature Reactor (VHTR) is one of six conceptual designs proposed for Generation IV nuclear reactors. Alloy 617, a solid solution strengthened Ni-base superalloy, is currently the primary candidate material for the tubing of the Intermediate Heat Exchanger (IHX) in the VHTR design. Steady-state operation of the nuclear power plant at elevated temperatures leads to creep deformation, whereas loading transients including startup and shutdown generate fatigue. A detailed understanding of the creep-fatigue interaction in Alloy 617 is necessary before it can be considered as a material for nuclear construction in ASME Boiler and Pressure Vessel Code. Current design codes for components undergoing creep-fatigue interaction at elevated temperatures require creep-fatigue testing data covering the entire range from fatigue-dominant to creep-dominant loading. Classical strain-controlled tests, which produce stress relaxation during the hold period, show a saturation in cycle life with increasing hold periods due to the rapid stress-relaxation of Alloy 617 at high temperatures. Therefore, applying longer hold time in these tests cannot generate creep-dominated failure. In this study, uniaxial isothermal creep-fatigue tests with non-traditional loading waveforms were designed and performed at 850 and 950°C, with an objective of generating test data in the creep-dominant regime. The new loading waveforms are hybrid strain-controlled and force-controlled testing which avoid stress relaxation during the creep hold. The experimental data showed varying proportions of creep and fatigue damage, and provided evidence for the inadequacy of the widely-used time fraction rule for estimating creep damage under creep-fatigue conditions. Micro-scale damage features in failed test specimens, such as fatigue cracks and creep voids, were quantified using a Scanning Electron Microscope (SEM) to find a correlation between creep and fatigue damage. Quantitative statistical imaging analysis showed that the microstructural damage features (cracks and voids) are correlated with a new mechanical driving force parameter. The results from this image-based damage analysis were used to develop a phenomenological life-prediction methodology called the effective time fraction approach. Finally, the constitutive creep-fatigue response of the material at 950°C was modeled using a unified viscoplastic model coupled with a damage accumulation model. The simulation results were used to validate an energy-based constitutive life-prediction model, as a mechanistic model for potential component and structure level creep-fatigue analysis.

An upper-limb power-assist exoskeleton using proportional myoelectric control.

PubMed

Tang, Zhichuan; Zhang, Kejun; Sun, Shouqian; Gao, Zenggui; Zhang, Lekai; Yang, Zhongliang

2014-04-10

We developed an upper-limb power-assist exoskeleton actuated by pneumatic muscles. The exoskeleton included two metal links: a nylon joint, four size-adjustable carbon fiber bracers, a potentiometer and two pneumatic muscles. The proportional myoelectric control method was proposed to control the exoskeleton according to the user's motion intention in real time. With the feature extraction procedure and the classification (back-propagation neural network), an electromyogram (EMG)-angle model was constructed to be used for pattern recognition. Six healthy subjects performed elbow flexion-extension movements under four experimental conditions: (1) holding a 1-kg load, wearing the exoskeleton, but with no actuation and for different periods (2-s, 4-s and 8-s periods); (2) holding a 1-kg load, without wearing the exoskeleton, for a fixed period; (3) holding a 1-kg load, wearing the exoskeleton, but with no actuation, for a fixed period; (4) holding a 1-kg load, wearing the exoskeleton under proportional myoelectric control, for a fixed period. The EMG signals of the biceps brachii, the brachioradialis, the triceps brachii and the anconeus and the angle of the elbow were collected. The control scheme's reliability and power-assist effectiveness were evaluated in the experiments. The results indicated that the exoskeleton could be controlled by the user's motion intention in real time and that it was useful for augmenting arm performance with neurological signal control, which could be applied to assist in elbow rehabilitation after neurological injury.

Prospective MR image alignment between breath-holds: Application to renal BOLD MRI.

PubMed

Kalis, Inge M; Pilutti, David; Krafft, Axel J; Hennig, Jürgen; Bock, Michael

2017-04-01

To present an image registration method for renal blood oxygen level-dependent (BOLD) measurements that enables semiautomatic assessment of parenchymal and medullary R2* changes under a functional challenge. In a series of breath-hold acquisitions, three-dimensional data were acquired initially for prospective image registration of subsequent BOLD measurements. An algorithm for kidney alignment for BOLD renal imaging (KALIBRI) was implemented to detect the positions of the left and right kidney so that the kidneys were acquired in the subsequent BOLD measurement at consistent anatomical locations. Residual in-plane distortions were corrected retrospectively so that semiautomatic dynamic R2* measurements of the renal cortex and medulla become feasible. KALIBRI was tested in six healthy volunteers during a series of BOLD experiments, which included a 600- to 1000-mL water challenge. Prospective image registration and BOLD imaging of each kidney was achieved within a total measurement time of about 17 s, enabling its execution within a single breath-hold. KALIBRI improved the registration by up to 35% as found with mutual information measures. In four volunteers, a medullary R2* decrease of up to 40% was observed after water ingestion. KALIBRI improves the quality of two-dimensional time-resolved renal BOLD MRI by aligning local renal anatomy, which allows for consistent R2* measurements over many breath-holds. Magn Reson Med 77:1573-1582, 2017. © 2016 International Society for Magnetic Resonance in Medicine. © 2016 International Society for Magnetic Resonance in Medicine.

Cardiovascular magnetic resonance assessment of acute cardiovascular effects of voluntary apnoea in elite divers.

PubMed

Eichhorn, L; Doerner, J; Luetkens, J A; Lunkenheimer, J M; Dolscheid-Pommerich, R C; Erdfelder, F; Fimmers, R; Nadal, J; Stoffel-Wagner, B; Schild, H H; Hoeft, A; Zur, B; Naehle, C P

2018-06-18

Prolonged breath holding results in hypoxemia and hypercapnia. Compensatory mechanisms help maintain adequate oxygen supply to hypoxia sensitive organs, but burden the cardiovascular system. The aim was to investigate human compensatory mechanisms and their effects on the cardiovascular system with regard to cardiac function and morphology, blood flow redistribution, serum biomarkers of the adrenergic system and myocardial injury markers following prolonged apnoea. Seventeen elite apnoea divers performed maximal breath-hold during cardiovascular magnetic resonance imaging (CMR). Two breath-hold sessions were performed to assess (1) cardiac function, myocardial tissue properties and (2) blood flow. In between CMR sessions, a head MRI was performed for the assessment of signs of silent brain ischemia. Urine and blood samples were analysed prior to and up to 4 h after the first breath-hold. Mean breath-hold time was 297 ± 52 s. Left ventricular (LV) end-systolic, end-diastolic, and stroke volume increased significantly (p < 0.05). Peripheral oxygen saturation, LV ejection fraction, LV fractional shortening, and heart rate decreased significantly (p < 0.05). Blood distribution was diverted to cerebral regions with no significant changes in the descending aorta. Catecholamine levels, high-sensitivity cardiac troponin, and NT-pro-BNP levels increased significantly, but did not reach pathological levels. Compensatory effects of prolonged apnoea substantially burden the cardiovascular system. CMR tissue characterisation did not reveal acute myocardial injury, indicating that the resulting cardiovascular stress does not exceed compensatory physiological limits in healthy subjects. However, these compensatory mechanisms could overly tax those limits in subjects with pre-existing cardiac disease. For divers interested in competetive apnoea diving, a comprehensive medical exam with a special focus on the cardiovascular system may be warranted. This prospective single-centre study was approved by the institutional ethics committee review board. It was retrospectively registered under ClinicalTrials.gov (Trial registration: NCT02280226 . Registered 29 October 2014).

Role of route previewing strategies on climbing fluency and exploratory movements.

PubMed

Seifert, Ludovic; Cordier, Romain; Orth, Dominic; Courtine, Yoan; Croft, James L

2017-01-01

This study examined the role of route previewing strategies on climbing fluency and on exploratory movements of the limbs, in order to understand whether previewing helps people to perceive and to realize affordances. Eight inexperienced and ten experienced climbers previewed a 10 m high route of 5b difficulty on French scale, then climbed it with a top-rope as fluently as possible. Gaze behavior was collected from an eye tracking system during the preview and allowed us to determine the number of times they scanned the route, and which of four route previewing strategies (fragmentary, ascending, zigzagging, and sequence-of-blocks) they used. Five inertial measurement units (IMU) (3D accelerometer, 3D gyroscope, 3D magnetometer) were attached to the hip, both feet, and forearms to analyze the vertical acceleration and direction of each limb and hip during the ascent. We were able to detect movement and immobility phases of each IMU using segmentation and classification processes. Depending on whether the limbs and/or hip were moving, five states of behavior were detected: immobility, postural regulation, hold exploration, hold change, and hold traction. Using cluster analysis we identified four clusters of gaze behavior during route previewing depending on route preview duration, number of scan paths, fixations duration, ascending, zigzagging, and sequence-of-blocks strategies. The number of scan paths was positively correlated with relative duration of exploration and negatively correlated with relative duration of hold changes during the ascent. Additionally, a high relative duration of sequence-of-blocks strategy and zigzagging strategy were associated with a high relative duration of immobility during the ascent. Route previewing might help to pick up functional information about reachable, graspable, and usable holds, in order to chain movements together and to find the route. In other words, route previewing might contribute to perceiving and realizing nested affordances.

Evaluation of Cyclic Behavior of Aircraft Turbine Disk Alloys

NASA Technical Reports Server (NTRS)

Shahani, V.; Popp, H. G.

1978-01-01

An evaluation of the cyclic behavior of three aircraft engine turbine disk materials was conducted to compare their relative crack initiation and crack propagation resistance. The disk alloys investigated were Inconel 718, hot isostatically pressed and forged powder metallurgy Rene '95, and as-hot-isostatically pressed Rene '95. The objective was to compare the hot isostatically pressed powder metallurgy alloy forms with conventionally processed superalloys as represented by Inconel 718. Cyclic behavior was evaluated at 650 C both under continuously cycling and a fifteen minute tensile hold time cycle to simulate engine conditions. Analysis of the test data were made to evaluate the strain range partitioning and energy exhaustion concepts for predicting hold time effects on low cycle fatigue.

SU-E-J-223: A BOLD Contrast Imaging Sequence to Evaluate Oxygenation Changes Due to Breath Holding for Breast Radiotherapy: A Pilot Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adamson, J; Chang, Z; Cai, J

Purpose: To develop a robust MRI sequence to measure BOLD breath hold induced contrast in context of breast radiotherapy. Methods: Two sequences were selected from prior studies as candidates to measure BOLD contrast attributable to breath holding within the breast: (1) T2* based Gradient Echo EPI (TR/TE = 500/41ms, flip angle = 60°), and (2) T2 based Single Shot Fast Spin Echo (SSFSE) (TR/TE = 3000/60ms). We enrolled ten women post-lumpectomy for breast cancer who were undergoing treatment planning for whole breast radiotherapy. Each session utilized a 1.5T GE MRI and 4 channel breast coil with the subject immobilized pronemore » on a custom board. For each sequence, 1–3 planes of the lumpectomy breast were imaged continuously during a background measurement (1min) and intermittent breath holds (20–40s per breath hold, 3–5 holds per sequence). BOLD contrast was quantified as correlation of changes in per-pixel intensity with the breath hold schedule convolved with a hemodynamic response function. Subtle motion was corrected using a deformable registration algorithm. Correlation with breath-holding was considered significant if p<0.001. Results: The percentage of the breast ROI with positive BOLD contrast measured by the two sequences were in agreement with a correlation coefficient of R=0.72 (p=0.02). While both sequences demonstrated areas with strong BOLD response, the response was more systematic throughout the breast for the SSFSE (T2) sequence (% breast with response in the same direction: 51.2%±0.7% for T2* vs. 68.1%±16% for T2). In addition, the T2 sequence was less prone to magnetic susceptibility artifacts, especially in presence of seroma, and provided a more robust image with little distortion or artifacts. Conclusion: A T2 SSFSE sequence shows promise for measuring BOLD contrast in the context of breast radiotherapy utilizing a breath hold technique. Further study in a larger patient cohort is warranted to better refine this novel technique.« less

Time-Dependent Fatigue Crack Propagation Behavior of Two Solid-Solution-Strengthened Ni-Based Superalloys—INCONEL 617 and HAYNES 230

NASA Astrophysics Data System (ADS)

Ma, Longzhou; Roy, Shawoon K.; Hasan, Muhammad H.; Pal, Joydeep; Chatterjee, Sudin

2012-02-01

The fatigue crack propagation (FCP) as well as the sustained loading crack growth (SLCG) behavior of two solid-solution-strengthened Ni-based superalloys, INCONEL 617 (Special Metals Corporation Family of Companies) and HAYNES 230 (Haynes International, Inc., Kokomo, IN), were studied at increased temperatures in laboratory air under a constant stress-intensity-factor ( K) condition. The crack propagation tests were conducted using a baseline cyclic triangular waveform with a frequency of 1/3 Hz. Various hold times were imposed at the maximum load of a fatigue cycle to study the hold time effect. The results show that a linear elastic fracture mechanics (LEFM) parameter, stress intensity factor ( K), is sufficient to describe the FCP and SLCG behavior at the testing temperatures ranging from 873 K to 1073 K (600 °C to 800 °C). As observed in the precipitation-strengthened superalloys, both INCONEL 617 and HAYNES 230 exhibited the time-dependent FCP, steady SLCG behavior, and existence of a damage zone ahead of crack tip. A thermodynamic equation was adapted to correlate the SLCG rates to determine thermal activation energy. The fracture modes associated with crack propagation behavior were discussed, and the mechanism of time-dependent FCP as well as SLCG was identified. Compared with INCONEL 617, the lower crack propagation rates of HAYNES 230 under the time-dependent condition were ascribed to the different fracture mode and the presence of numerous W-rich M6C-type and Cr-rich M23C6-type carbides. Toward the end, a phenomenological model was employed to correlate the FCP rates at cycle/time-dependent FCP domain. All the results suggest that an environmental factor, the stress assisted grain boundary oxygen embrittlement (SAGBOE) mechanism, is mainly responsible for the accelerated time-dependent FCP rates of INCONEL 617 and HAYNES 230.

78 FR 26031 - Sunshine Act Notice

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-03

... EQUAL EMPLOYMENT OPPORTUNITY COMMISSION Sunshine Act Notice AGENCY HOLDING THE MEETING: Equal Employment Opportunity Commission DATE AND TIME: Wednesday, May 8, 2013, 9:00 a.m. Eastern Time. PLACE.... Announcement of Notation Votes, and 2. Wellness Programs Under Federal Equal Employment Opportunity Laws. Note...

"Time" in China.

ERIC Educational Resources Information Center

Weland, James E.

1982-01-01

Discusses how the Chinese have recorded their history by dynasties, the length of time any one imperial clan could retain its hold on the Dragon Throne. Dynastic histories were used to instruct rulers in the ways ethical problems of government had been dealt with in the past. (AM)

A study of creep crack growth in 2219-T851

NASA Astrophysics Data System (ADS)

Bensussan, Philippe L.; Jablonski, David A.; Pelloux, Regis M.

1984-01-01

Creep crack growth rates were measured in high strength 2219-T851 aluminum alloy with a computerized fully automated test procedure. Crack growth tests were performed on CT specimens with side grooves. The experimental set-up is described. During a test, the specimen is cyclically loaded on a servohydraulic testing machine under computer control, maintained at maximum load for a given hold time at each cycle, unloaded, and then reloaded. Crack lengths are obtained from compliance measurements recorded during each unloading. It is shown that the measured crack growth rates per cycle do represent creep crack growth rates per unit time for hold times longer than 10 seconds. The validity of LEFM concepts for side-grooved specimens is reviewed, and compliance and stress intensity factor calibrations for such specimens are reported. For the range of testing conditions of this study, 2219-T851 is shown to be creep brittle in terms of concepts of fracture mechanics of creeping solids. It is found that, under these testing conditions, a correlation exists between the creep crack growth rates under plane strain conditions and the stress intensity factor ( da/dt = A K 3.8 at 175 °C) for simple K histories in a regime of steady or quasi-steady state crack growth. The micromechanisms of fracture are determined to be of complex nature. The fracture mode is observed to be mixed inter- and transgranular, the relative amount of intergranular fracture decreasing as K and da/dt increase.

17 CFR 1.23 - Interest of futures commission merchant in segregated futures customer funds; additions and...

Code of Federal Regulations, 2014 CFR

2014-04-01

... any and all futures customers' accounts from becoming undersegregated at any time. (2) If a futures commission merchant discovers at any time that it is holding insufficient funds in segregated accounts to... with the segregated funds requirements at all times. Each futures commission merchant shall establish...

78 FR 76177 - Sunshine Act Meeting Notice; Change of Time of Sunshine Act Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-16

... INTERNATIONAL TRADE COMMISSION [USITC SE-13-036] Sunshine Act Meeting Notice; Change of Time of Sunshine Act Meeting AGENCY HOLDING THE MEETING: United States International Trade Commission. DATE: December 13, 2013. NEW TIME: 9:30 a.m. PLACE: Room 101, 500 E Street SW., Washington, DC 20436, Telephone...

Priming Students for Success through Energy Management: The Balancing Act

ERIC Educational Resources Information Center

Pueschel, Andrew; Tucker, Mary L.; Rosado-Fager, Ana; Taylor-Bianco, Amy; Sullivan, Gregory

2018-01-01

University students are increasingly more involved as they juggle managing life away from family, making time for coursework, organizational commitments, and social engagements as well as, for many, holding full-time jobs. At a time when students' lives are more intense than ever, many are at a distinct disadvantage because of inadequate energy…

Effective heat inactivation of Mycobacterium avium subsp. paratuberculosis in raw milk contaminated with naturally infected feces.

PubMed

Rademaker, Jan L W; Vissers, Marc M M; Te Giffel, Meike C

2007-07-01

The effectiveness of high-temperature, short holding time (HTST) pasteurization and homogenization with respect to inactivation of Mycobacterium avium subsp. paratuberculosis was evaluated quantitatively. This allowed a detailed determination of inactivation kinetics. High concentrations of feces from cows with clinical symptoms of Johne's disease were used to contaminate raw milk in order to realistically mimic possible incidents most closely. Final M. avium subsp. paratuberculosis concentrations varying from 10(2) to 3.5 x 10(5) cells per ml raw milk were used. Heat treatments including industrial HTST were simulated on a pilot scale with 22 different time-temperature combinations, including 60 to 90 degrees C at holding (mean residence) times of 6 to 15 s. Following 72 degrees C and a holding time of 6 s, 70 degrees C for 10 and 15 s, or under more stringent conditions, no viable M. avium subsp. paratuberculosis cells were recovered, resulting in >4.2- to >7.1-fold reductions, depending on the original inoculum concentrations. Inactivation kinetic modeling of 69 quantitative data points yielded an E(a) of 305,635 J/mol and an lnk(0) of 107.2, corresponding to a D value of 1.2 s at 72 degrees C and a Z value of 7.7 degrees C. Homogenization did not significantly affect the inactivation. The conclusion can be drawn that HTST pasteurization conditions equal to 15 s at > or =72 degrees C result in a more-than-sevenfold reduction of M. avium subsp. paratuberculosis.

Effective Heat Inactivation of Mycobacterium avium subsp. paratuberculosis in Raw Milk Contaminated with Naturally Infected Feces▿

PubMed Central

Rademaker, Jan L. W.; Vissers, Marc M. M.; te Giffel, Meike C.

2007-01-01

The effectiveness of high-temperature, short holding time (HTST) pasteurization and homogenization with respect to inactivation of Mycobacterium avium subsp. paratuberculosis was evaluated quantitatively. This allowed a detailed determination of inactivation kinetics. High concentrations of feces from cows with clinical symptoms of Johne's disease were used to contaminate raw milk in order to realistically mimic possible incidents most closely. Final M. avium subsp. paratuberculosis concentrations varying from 102 to 3.5 × 105 cells per ml raw milk were used. Heat treatments including industrial HTST were simulated on a pilot scale with 22 different time-temperature combinations, including 60 to 90°C at holding (mean residence) times of 6 to 15 s. Following 72°C and a holding time of 6 s, 70°C for 10 and 15 s, or under more stringent conditions, no viable M. avium subsp. paratuberculosis cells were recovered, resulting in >4.2- to >7.1-fold reductions, depending on the original inoculum concentrations. Inactivation kinetic modeling of 69 quantitative data points yielded an Ea of 305,635 J/mol and an lnk0 of 107.2, corresponding to a D value of 1.2 s at 72°C and a Z value of 7.7°C. Homogenization did not significantly affect the inactivation. The conclusion can be drawn that HTST pasteurization conditions equal to 15 s at ≥72°C result in a more-than-sevenfold reduction of M. avium subsp. paratuberculosis. PMID:17496131

The influence of high heat input and inclusions control for rare earth on welding in low alloy high strength steel

NASA Astrophysics Data System (ADS)

Chu, Rensheng; Mu, Shukun; Liu, Jingang; Li, Zhanjun

2017-09-01

In the current paper, it is analyzed for the influence of high heat input and inclusions control for rare earth on welding in low alloy high strength steel. It is observed for the structure for different heat input of the coarse-grained area. It is finest for the coarse grain with the high heat input of 200 kJ / cm and the coarse grain area with 400 kJ / cm is the largest. The performance with the heat input of 200 kJ / cm for -20 °C V-shaped notch oscillatory power is better than the heat input of 400 kJ / cm. The grain structure is the ferrite and bainite for different holding time. The grain structure for 5s holding time has a grain size of 82.9 μm with heat input of 200 kJ/cm and grain size of 97.9 μm for 10s holding time. For the inclusions for HSLA steel with adding rare earth, they are Al2O3-CaS inclusions in the Al2O3-CaS-CaO ternary phase diagram. At the same time, it can not be found for low melting calcium aluminate inclusions compared to the inclusions for the HSLA steel without rare earth. Most of the size for the inclusions is between 1 ~ 10μm. The overall grain structure is smaller and the welding performance is more excellent for adding rare earth.

The basis for the development of a fuselage evacuation time for a ditched helicopter.

PubMed

Brooks, C J; Muir, H C; Gibbs, P N

2001-06-01

When a helicopter ditches or crashes in water, unless the buoyancy bags are inflated, it commonly sinks inverted. Thus, crew and passengers must make an underwater escape. It is postulated that later passengers in the escape sequence do not have the breath-holding ability to conduct a successful escape, particularly if the water is cold. This contributes to the 20-50% mortality rate in survivable accidents. There were 132 immersed subject evaluations which were conducted in daylight and darkness to measure escape times from a helicopter underwater escape trainer, configured to the Super Puma, seated for 15 and 18 passengers. The subjects were highly experienced instructors or Navy clearance divers. The time from when each subject's head disappeared underwater until each subject surfaced and total fuselage evacuation time were measured and any problems hampering escape were noted. Breath-holding for the last subject out ranged from 28 to 92 s. An emergency breathing system was used by a minimum of four subjects each time and a maximum of 11 subjects in one condition. The buoyancy of the survival suit was the principal component that hampered escape. Breath-holding times were too long for the later subjects to escape without resorting to an EBS, in spite of the fact that they were highly trained. For regular crew and passengers flying over water, this would explain the high mortality, etc. Therefore, a new helicopter standard should be developed requiring fuselage design to accommodate total evacuation within 20 s from underwater. For current helicopters, where this cannot be achieved, passengers should be provided with some form of air supply, or, after ditching, the helicopter should be modified so that it will stay afloat on its side and retain an air space in the cabin.

Microwave assisted extraction of iodine and bromine from edible seaweed for inductively coupled plasma-mass spectrometry determination.

PubMed

Romarís-Hortas, Vanessa; Moreda-Piñeiro, Antonio; Bermejo-Barrera, Pilar

2009-08-15

The feasibility of microwave energy to assist the solubilisation of edible seaweed samples by tetramethylammonium hydroxide (TMAH) has been investigated to extract iodine and bromine. Inductively coupled plasma-mass spectrometry (ICP-MS) has been used as a multi-element detector. Variables affecting the microwave assisted extraction/solubilisation (temperature, TMAH volume, ramp time and hold time) were firstly screened by applying a fractional factorial design (2(5-1)+2), resolution V and 2 centre points. When extracting both halogens, results showed statistical significance (confidence interval of 95%) for TMAH volume and temperature, and also for the two order interaction between both variables. Therefore, these two variables were finally optimized by a 2(2)+star orthogonal central composite design with 5 centre points and 2 replicates, and optimum values of 200 degrees C and 10 mL for temperature and TMAH volume, respectively, were found. The extraction time (ramp and hold times) was found statistically non-significant, and values of 10 and 5 min were chosen for the ramp time and the hold time, respectively. This means a fast microwave heating cycle. Repeatability of the over-all procedure has been found to be 6% for both elements, while iodine and bromine concentrations of 24.6 and 19.9 ng g(-1), respectively, were established for the limit of detection. Accuracy of the method was assessed by analyzing the NIES-09 (Sargasso, Sargassum fulvellum) certified reference material (CRM) and the iodine and bromine concentrations found have been in good agreement with the indicative values for this CRM. Finally, the method was applied to several edible dried and canned seaweed samples.

Effect of holding office on the behavior of politicians

PubMed Central

Enemark, Daniel; Gibson, Clark C.; McCubbins, Mathew D.; Seim, Brigitte

2016-01-01

Reciprocity is central to our understanding of politics. Most political exchanges—whether they involve legislative vote trading, interbranch bargaining, constituent service, or even the corrupt exchange of public resources for private wealth—require reciprocity. But how does reciprocity arise? Do government officials learn reciprocity while holding office, or do recruitment and selection practices favor those who already adhere to a norm of reciprocity? We recruit Zambian politicians who narrowly won or lost a previous election to play behavioral games that provide a measure of reciprocity. This combination of regression discontinuity and experimental designs allows us to estimate the effect of holding office on behavior. We find that holding office increases adherence to the norm of reciprocity. This study identifies causal effects of holding office on politicians’ behavior. PMID:27856736

Effect of holding office on the behavior of politicians.

PubMed

Enemark, Daniel; Gibson, Clark C; McCubbins, Mathew D; Seim, Brigitte

2016-11-29

Reciprocity is central to our understanding of politics. Most political exchanges-whether they involve legislative vote trading, interbranch bargaining, constituent service, or even the corrupt exchange of public resources for private wealth-require reciprocity. But how does reciprocity arise? Do government officials learn reciprocity while holding office, or do recruitment and selection practices favor those who already adhere to a norm of reciprocity? We recruit Zambian politicians who narrowly won or lost a previous election to play behavioral games that provide a measure of reciprocity. This combination of regression discontinuity and experimental designs allows us to estimate the effect of holding office on behavior. We find that holding office increases adherence to the norm of reciprocity. This study identifies causal effects of holding office on politicians' behavior.

Contact and nutrient caregiving effects on newborn infant pain responses.

PubMed

Gormally, S; Barr, R G; Wertheim, L; Alkawaf, R; Calinoiu, N; Young, S N

2001-01-01

To understand how the 'caregiving context' could affect responses to procedural pain, the authors sought to determine whether (1) the combined effects of sweet taste and holding (caregiving contact) were greater than the effects of either alone, (2) any combined effects were additive or interactive, and (3) the interventions had similar effects on behavioral (crying and facial activity) and physiological (heart rate, vagal tone) responses to the heel-stick procedure in newborn infants in a randomized two-factorial intervention trial. Eighty-five normally developing newborn infants were studied with a mean gestational age of 39.4 weeks on the 2nd or 3rd day of life. Infants were randomized in blocks of eight to receive (1) no holding and water taste (control participants), (2) no holding and sucrose taste (sucrose group), (3) holding and water taste (holding group), or (4) holding and sucrose taste (holding and sucrose group). Crying was reduced significantly by taste and holding, and the interventions combined additively. Facial activity was only significantly reduced by holding. For physiological measures, the interventions interacted with each other and preintervention levels to reduce heart rate and lower vagal tone more during the procedure in infants in whom heart rate and vagal tone were higher before intervention. Consequently, sweet taste and holding interventions combined in complex ways when acting on different behavioral and physiological response systems to modify stressful pain experiences. The results suggest that providing a caregiving context when painful procedures are performed may be a simple and practical method of reducing pain experience in infants, and that no one measure captures these effects.

Development of Highly Ductile Spheroidized Steel from High C (0.61 wt.% C) Low-Alloy Steel

NASA Astrophysics Data System (ADS)

Monia, S.; Varshney, A.; Gouthama; Sangal, S.; Kundu, S.; Samanta, S.; Mondal, K.

2015-11-01

This research aims to develop a multiphase steel combining spheroidal cementite and bainite in ductile ferrite matrix possessing an optimal balance of reasonably high strength and excellent ductility. A high carbon (0.61 wt.%) high silicon (1.71 wt.%) EN45 spring steel was annealed to obtain ferrite pearlite microstructure. The samples were given 5 and 10% cold rolling followed by holding at temperature below Ac1 for about 3 h. The samples were then held in intercritical range at 770 °C temperature for different durations ranging from 5 to 20 min for partial re-austenitization followed by quenching in a salt bath maintained at 350 °C and holding for 10 min to get bainite. The samples were finally water quenched. Characterizations of the samples with the help of optical microscopy, x-ray diffraction, scanning electron microscopy, and atomic force microscopy were carried out. Optimal heat-treatment conditions were found out after correlating with tensile properties. The best combination of high tensile strength (~800 MPa) with very high elongation (~29%) was obtained. Effects of cold-rolled strain and holding time in the intercritical region on the mechanical properties and microstructural changes were studied. Finally, structural property correlation is established.

Mapping cerebrovascular reactivity using concurrent fMRI and near infrared spectroscopy

NASA Astrophysics Data System (ADS)

Tong, Yunjie; Bergethon, Peter R.; Frederick, Blaise d.

2011-02-01

Cerebrovascular reactivity (CVR) reflects the compensatory dilatory capacity of cerebral vasculature to a dilatory stimulus and is an important indicator of brain vascular reserve. fMRI has been proven to be an effective imaging technique to obtain the CVR map when the subjects perform CO2 inhalation or the breath holding task (BH). However, the traditional data analysis inaccurately models the BOLD using a boxcar function with fixed time delay. We propose a novel way to process the fMRI data obtained during a blocked BH by using the simultaneously collected near infrared spectroscopy (NIRS) data as regressor1. In this concurrent NIRS and fMRI study, 6 healthy subjects performed a blocked BH (5 breath holds with 20s durations intermitted by 40s of regular breathing). A NIRS probe of two sources and two detectors separated by 3 cm was placed on the right side of prefrontal area of the subjects. The time course of changes in oxy-hemoglobin (Δ[HbO]) was calculated from NIRS data and shifted in time by various amounts, and resampled to the fMRI acquisition rate. Each shifted time course was used as regressor in FEAT (the analysis tool in FSL). The resulting z-statistic maps were concatenated in time and the maximal value was taken along the time for all the voxels to generate a 3-D CVR map. The new method produces more accurate and thorough CVR maps; moreover, it enables us to produce a comparable baseline cerebral vascular map if applied to resting state (RS) data.

A Proof of the Occupancy Principle and the Mean-Transit-Time Theorem for Compartmental Models

PubMed Central

RAMAKRISHNAN, RAJASEKHAR; LEONARD, EDWARD F.; DELL, RALPH B.

2012-01-01

The occupancy principle and the mean-transit-time theorem are derived for the passage of a tracer through a system that can be described by a general pool model. It is proved, using matrix theory, that if (and only if) tracer entering the system labels equally all tracee fluxes into the system, then the integral of the tracer concentration is the same in all the pools. It is also proved that if, in addition, all flow out of the system is through the observation point, the first moment of the tracer concentration at the observation point can be used to calculate the total amount of trace in the system. The necessity of this condition is analyzed. Examples are given of models in which the occupancy principle and the mean-transit-time theorem hold or do not hold. PMID:22328793

Studies of the Ability to Hold the Eye in Eccentric Gaze: Measurements in Normal Subjects with the Head Erect

NASA Technical Reports Server (NTRS)

Reschke, Millard F.; Somers, Jeffrey T.; Feiveson, Alan H.; Leigh, R. John; Wood, Scott J.; Paloski, William H.; Kornilova, Ludmila

2006-01-01

We studied the ability to hold the eyes in eccentric horizontal or vertical gaze angles in 68 normal humans, age range 19-56. Subjects attempted to sustain visual fixation of a briefly flashed target located 30 in the horizontal plane and 15 in the vertical plane in a dark environment. Conventionally, the ability to hold eccentric gaze is estimated by fitting centripetal eye drifts by exponential curves and calculating the time constant (t(sub c)) of these slow phases of gazeevoked nystagmus. Although the distribution of time-constant measurements (t(sub c)) in our normal subjects was extremely skewed due to occasional test runs that exhibited near-perfect stability (large t(sub c) values), we found that log10(tc) was approximately normally distributed within classes of target direction. Therefore, statistical estimation and inference on the effect of target direction was performed on values of z identical with log10t(sub c). Subjects showed considerable variation in their eyedrift performance over repeated trials; nonetheless, statistically significant differences emerged: values of tc were significantly higher for gaze elicited to targets in the horizontal plane than for the vertical plane (P less than 10(exp -5), suggesting eccentric gazeholding is more stable in the horizontal than in the vertical plane. Furthermore, centrifugal eye drifts were observed in 13.3, 16.0 and 55.6% of cases for horizontal, upgaze and downgaze tests, respectively. Fifth percentile values of the time constant were estimated to be 10.2 sec, 3.3 sec and 3.8 sec for horizontal, upward and downward gaze, respectively. The difference between horizontal and vertical gazeholding may be ascribed to separate components of the velocity position neural integrator for eye movements, and to differences in orbital mechanics. Our statistical method for representing the range of normal eccentric gaze stability can be readily applied in a clinical setting to patients who were exposed to environments that may have modified their central integrators and thus require monitoring. Patients with gaze-evoked nystagmus can be flagged by comparing to the above established normative criteria.

The Pineal Gland

ERIC Educational Resources Information Center

Kimbrough, T. Daniel; Llewellyn, Gerald C.

1973-01-01

Describes a surgical technique for performing pinealectomics, applicable to classroom and laboratory studies, by using a head-holding device for small animals and a flat dissecting tray outfitted with holding straps for larger animals. (CC)

Enhancement of holding strength of cannulated screw supported with PMMA: a biomechanical study on femoral head [corrected].

PubMed

Zeynalov, Reşad; Ağır, İsmail; Akgülle, Ahmet Hamdi; Kocaoğlu, Barış; Yalçın, Mithat Selim

2015-07-01

The aim of this study was to evaluate the holding strength of cannulated screw with multiple holes on threaded area, supported with PMMA in femoral head. A total of 48 human femoral heads were divided into two groups after mineral density measurement with Q-CT. Seven-millimeter cannulated screws with multiple holes on threaded area supported with PMMA were used in the study group, while in the control group standard 7-mm cannulated screws were used. Each group was divided into three subgroups with eight femoral heads. Mineral density of each subgroup was equal to the other. Groups were compared in terms of pull-out, maximum extraction torque and cut-out. In pull-out group, maximum holding strength (N) was measured, while axial pull-out of 0.5 mm/sec applied with Instron. Results showed meaningful significant difference (p < 0.011) between two groups. In cut-out group, femoral heads were placed into Instron and loading was started from 5 N at 2 mm per minute at first, and it was continued until a failure, at least 5 mm, of implant was observed. Results showed significant difference (p < 0.05) between two groups. In maximum extraction group, 4° per second reverse torque (Nm) was applied with torque meter. Highest torque value was measured during extraction time, and results showed very significant difference (p < 0. 001) between two groups. The results of our new design of cannulated screw augmented with PMMA provided background data to clinical application.

Dynamics of glass-forming di-n-butyl phthalate as studied by NMR.

PubMed

Szcześniak, E; Głowinkowski, S; Suchański, W; Jurga, S

1997-04-01

Spin-lattice relaxation times T1 and nuclear Overhauser effect (NOE) enhancement factors for the individual ring carbons in di-n-butyl phthalate (DBF) show that the reorientational correlation function corresponding to the global dynamics in supercooled liquid can be described by a Davidson-Cole distribution. Measurements of proton spin-lattice relaxation times T1 and T1p, as well as 1H NMR spectra at temperatures below the glass transition temperature, Tg, reveal that the same distribution holds also for description of local dynamics in glassy DBF. The activation parameters of the motions detected are derived.

75 FR 20000 - Government in the Sunshine Act Meeting Notice; Change of Time of Commission Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-16

... INTERNATIONAL TRADE COMMISSION [USITC SE-10-011] Government in the Sunshine Act Meeting Notice; Change of Time of Commission Meeting Agency Holding the Meeting: United States International Trade Commission. Original Date and Time: April 15, 2010 at 11 a.m. New Date and Time: April 15, 2010 at 2:30 p.m...

78 FR 76177 - Sunshine Act Meeting Notice; Change of Date and Time of Sunshine Act Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-16

... INTERNATIONAL TRADE COMMISSION [USITC SE-13-037] Sunshine Act Meeting Notice; Change of Date and Time of Sunshine Act Meeting AGENCY HOLDING THE MEETING: United States International Trade Commission. ORIGINAL DATE AND TIME: December 10, 2013 at 11:00 a.m. NEW TIME: December 11, 2013 at 12:00 p.m. PLACE...

Deformation Behavior of SiC/2014 Al Metal-Matrix Composite

DTIC Science & Technology

1989-05-01

the 2014 aluminum is an Al-Cu alloy with the eutectic temperature equal to 5400C, at which the specimens were tested in this study. Summary Room...temperature, decreasing heating rate, and increasing holding time, while ductility increased under the same condition until the eutectic temperature 540...drastically reduced the ductility to 1.5 percent. At high temperature, the modulus decreases but retains a large portion of it even at the eutectic

Signal transmission competing with noise in model excitable brains

NASA Astrophysics Data System (ADS)

Marro, J.; Mejias, J. F.; Pinamonti, G.; Torres, J. J.

2013-01-01

This is a short review of recent studies in our group on how weak signals may efficiently propagate in a system with noise-induced excitation-inhibition competition which adapts to the activity at short-time scales and thus induces excitable conditions. Our numerical results on simple mathematical models should hold for many complex networks in nature, including some brain cortical areas. In particular, they serve us here to interpret available psycho-technical data.

78 FR 2397 - Sunshine Act Notice

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-11

... EQUAL EMPLOYMENT OPPORTUNITY COMMISSION Sunshine Act Notice AGENCY HOLDING THE MEETING: Equal Employment Opportunity Commission. DATE AND TIME: Wednesday, January 16, 2013, 9:30 a.m. Eastern Time. PLACE: Commission Meeting Room on the First Floor of the EEOC Office Building, 131 ``M'' Street NE., Washington, DC...

76 FR 7562 - Sunshine Act Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-10

... EQUAL EMPLOYMENT OPPORTUNITY COMMISSION Sunshine Act Meeting AGENCY HOLDING THE MEETING: Equal Employment Opportunity Commission. DATE AND TIME: Wednesday, February 16, 2011, 9:30 a.m. Eastern Time. PLACE.... Announcement of Notation Votes, and 2. Out of work, out of luck? Denying employment opportunities to unemployed...

Holding Back, Intimacy, and Psychological and Relationship Outcomes Among Couples Coping With Prostate Cancer

PubMed Central

Manne, Sharon L.; Zaider, Talia; Lee, David; Kissane, David; Kashy, Deborah; Heckman, Carolyn; Virtue, Shannon Myers

2016-01-01

The present study evaluated intimacy as a mechanism for the effects of holding back sharing concerns about cancer on couples’ psychological distress, well-being, and marital satisfaction using the actor-partner interdependence model (APIM), and evaluated 2 possible moderators of these associations: the number of patient and spouse cancer concerns. We had 139 men treated for localized prostate cancer in the past year and their spouses complete surveys about holding back sharing cancer concerns, intimacy, distress, and relationship satisfaction, as well as patient and spouse cancer concerns. APIM-indicated that the association between holding back sharing concerns, and patient and spouse distress, well-being, and relationship satisfaction could be partially accounted for by their influence on patient and spouse perceptions of relationship intimacy. The number of cancer concerns did not moderate the mediational model. Holding back has strong associations with both partners’ well-being and distress. Holding back sharing concerns was particularly detrimental for couples’ intimacy and relationship satisfaction. PMID:26192132

A theoretical and econometric analysis of the economic rationale backing the Public Utility Holding Company Act of 1935: A revisionist history

NASA Astrophysics Data System (ADS)

Schrade, William Ralph

This dissertation challenges the economic rationale which justified the passage of the Public Utility Holding Company Act. It argues that the public utility holding company was a dynamic organization which overcame regulatory and organizational obstacles preventing consolidation of a fragmented industry. The historical evidence shows the holding company acted as a unique creator of liquidity which lowered the cost of capital for its constituent companies. Its organizational contribution achieved production economies by coordinating production to take advantage of the stochastic nature of demand diversity. These results are supported by the application of cliometrics to the historical record left by the public utility holding company. Two additional contributions of this dissertation are that by studying holding company operations and its historical development, the modern observer gets a better understanding of how this industry was meant to work and it also shows how the private market will seek organizational remedies for imperfect resource markets and institutional impediments.

Motion management within two respiratory-gating windows: feasibility study of dual quasi-breath-hold technique in gated medical procedures

NASA Astrophysics Data System (ADS)

Kim, Taeho; Kim, Siyong; Park, Yang-Kyun; Youn, Kaylin K.; Keall, Paul; Lee, Rena

2014-11-01

A dual quasi-breath-hold (DQBH) technique is proposed for respiratory motion management (a hybrid technique combining breathing-guidance with breath-hold task in the middle). The aim of this study is to test a hypothesis that the DQBH biofeedback system improves both the capability of motion management and delivery efficiency. Fifteen healthy human subjects were recruited for two respiratory motion measurements (free breathing and DQBH biofeedback breathing for 15 min). In this study, the DQBH biofeedback system utilized the abdominal position obtained using an real-time position management (RPM) system (Varian Medical Systems, Palo Alto, USA) to audio-visually guide a human subject for 4 s breath-hold at EOI and 90% EOE (EOE90%) to improve delivery efficiency. We investigated the residual respiratory motion and the delivery efficiency (duty-cycle) of abdominal displacement within the gating window. The improvement of the abdominal motion reproducibility was evaluated in terms of cycle-to-cycle displacement variability, respiratory period and baseline drift. The DQBH biofeedback system improved the abdominal motion management capability compared to that with free breathing. With a phase based gating (mean ± std: 55  ±  5%), the averaged root mean square error (RMSE) of the abdominal displacement in the dual-gating windows decreased from 2.26 mm of free breathing to 1.16 mm of DQBH biofeedback (p-value = 0.007). The averaged RMSE of abdominal displacement over the entire respiratory cycles reduced from 2.23 mm of free breathing to 1.39 mm of DQBH biofeedback breathing in the dual-gating windows (p-value = 0.028). The averaged baseline drift dropped from 0.9 mm min-1 with free breathing to 0.09 mm min-1 with DQBH biofeedback (p-value = 0.048). The averaged duty-cycle with an 1 mm width of displacement bound increased from 15% of free breathing to 26% of DQBH biofeedback (p-value = 0.003). The study demonstrated that the DQBH biofeedback system has the potential to significantly reduce the residual respiratory motion with the improved duty cycle during the respiratory gating procedure.

Historical mapping reveals causes and temporal patterns of woodland contraction in Austur-Skaftafellssýsla from the 12th century AD to present

NASA Astrophysics Data System (ADS)

Sigurmundsson, Friðþór S.; Gísladóttir, Guðrún; Erlendsson, Egill; Þorbjarnarson, Höskuldur

2016-04-01

Land-cover changes in Iceland over the last millennium encompass birch (Betula pubescens) woodland depletion and extensive soil erosion. Yet few studies have focused on spatial change of birch woodland coverage in Iceland over centuries and why and how the woodland depletion took place. The main objectives of this study are: (1) to map the woodland distribution today in Austur-Skaftafellssýsla (3041 km2) in southern Iceland; (2) to map woodland holdings over a period of 900 years from eleventh. AD 1100 to the early 20th century; (3) explain the relative impacts of socio-economic and natural forces on woodland cover over this period. We use a combined approach of historical reconstruction from diverse written archives, GIS techniques and field work. The woodland in Austur-Skaftafellssýsla now covers 73.2 km2 (2.5% of the study area). The woodland holdings, 44 in total, are regularly listed in the church inventories from 1179 to 1570 and are owned by the church. In the first complete register for the district in 1641 the woodland holdings were 73, owned and used by 58 estates, and distributed across Austur-Skaftafellssýsla. All the main patches of woodland remain today, with the exception of four minor woodlands which were exhausted near the end of the 19th century. The woodland was used for firewood and charcoal making as well as grazing during the study period but, crucially, in most cases only one estate had authority over each holding, none were commons. The main driving force behind the development of woodlands was socio-economic, rather than natural, where the form of ownership was fundamental for the fate of the woodland. Harsh climate and volcanism were not directly responsible for woodland depletion. The latter half of the 19th century was the period of greatest woodland loss. This period coincides with considerable expansion in livestock numbers, especially sheep and associated all year around grazing, at a time when the Little Ice Age culminated in Iceland. Keywords: Deforestation. Soil erosion. Land ownership. GIS. Historical mapping.

Stochastic Stability of Nonlinear Sampled Data Systems with a Jump Linear Controller

NASA Technical Reports Server (NTRS)

Gonzalez, Oscar R.; Herencia-Zapana, Heber; Gray, W. Steven

2004-01-01

This paper analyzes the stability of a sampled- data system consisting of a deterministic, nonlinear, time- invariant, continuous-time plant and a stochastic, discrete- time, jump linear controller. The jump linear controller mod- els, for example, computer systems and communication net- works that are subject to stochastic upsets or disruptions. This sampled-data model has been used in the analysis and design of fault-tolerant systems and computer-control systems with random communication delays without taking into account the inter-sample response. To analyze stability, appropriate topologies are introduced for the signal spaces of the sampled- data system. With these topologies, the ideal sampling and zero-order-hold operators are shown to be measurable maps. This paper shows that the known equivalence between the stability of a deterministic, linear sampled-data system and its associated discrete-time representation as well as between a nonlinear sampled-data system and a linearized representation holds even in a stochastic framework.

The phenomenon of hand holding as a coping strategy in adolescents experiencing treatment-related pain.

PubMed

Weekes, D P; Kagan, S H; James, K; Seboni, N

1993-01-01

The purpose of this study was to understand the phenomenon of hand holding as a coping strategy used by adolescents to deal with treatment-related pain. The convenience sample consisted of 20 adolescents whose ages were 11 to 19 years: 10 had cancer and 10 had renal disease (this served as the comparison group). Using a descriptive design, a semistructured interview was conducted with each adolescent. To supplement and support interview data, structured observations were conducted as adolescents underwent painful treatments (eg, blood draws, shunt placement, peripheral chemotherapy, lumbar punctures, and bone marrow aspirations). Data were analyzed using descriptive statistics and qualitative analytic techniques similar to those delineated by Strauss and Corbin. The results of this study indicated that subjects in both the cancer and the renal disease group perceived hand holding to be a very effective coping strategy in ameliorating treatment-related pain. Overwhelmingly the patients preferred to hold their mother's hand. When the mother was unavailable, they preferred to hold a specific nurse's hand. Hand holding functioned to reduce tension associated with impending treatments, as a source of distraction, and as a source of security. Accordingly, adolescents' subjective experience of treatment-related pain was reduced when they felt more secure, less tense, and were distracted.

Real-time magnetic resonance imaging of cardiac function and flow—recent progress

PubMed Central

Zhang, Shuo; Joseph, Arun A.; Voit, Dirk; Schaetz, Sebastian; Merboldt, Klaus-Dietmar; Unterberg-Buchwald, Christina; Hennemuth, Anja; Lotz, Joachim

2014-01-01

Cardiac structure, function and flow are most commonly studied by ultrasound, X-ray and magnetic resonance imaging (MRI) techniques. However, cardiovascular MRI is hitherto limited to electrocardiogram (ECG)-synchronized acquisitions and therefore often results in compromised quality for patients with arrhythmias or inabilities to comply with requested protocols—especially with breath-holding. Recent advances in the development of novel real-time MRI techniques now offer dynamic imaging of the heart and major vessels with high spatial and temporal resolution, so that examinations may be performed without the need for ECG synchronization and during free breathing. This article provides an overview of technical achievements, physiological validations, preliminary patient studies and translational aspects for a future clinical scenario of cardiovascular MRI in real time. PMID:25392819

Note: Tesla based pulse generator for electrical breakdown study of liquid dielectrics

NASA Astrophysics Data System (ADS)

Veda Prakash, G.; Kumar, R.; Patel, J.; Saurabh, K.; Shyam, A.

2013-12-01

In the process of studying charge holding capability and delay time for breakdown in liquids under nanosecond (ns) time scales, a Tesla based pulse generator has been developed. Pulse generator is a combination of Tesla transformer, pulse forming line, a fast closing switch, and test chamber. Use of Tesla transformer over conventional Marx generators makes the pulse generator very compact, cost effective, and requires less maintenance. The system has been designed and developed to deliver maximum output voltage of 300 kV and rise time of the order of tens of nanoseconds. The paper deals with the system design parameters, breakdown test procedure, and various experimental results. To validate the pulse generator performance, experimental results have been compared with PSPICE simulation software and are in good agreement with simulation results.

Enhanced monitor system for water protection

DOEpatents

Hill, David E [Knoxville, TN; Rodriquez, Jr., Miguel [Oak Ridge, TN; Greenbaum, Elias [Knoxville, TN

2009-09-22

An automatic, self-contained device for detecting toxic agents in a water supply includes an analyzer for detecting at least one toxic agent in a water sample, introducing a means for introducing a water sample into the analyzer and discharging the water sample from the analyzer, holding means for holding a water sample for a pre-selected period of time before the water sample is introduced into the analyzer, and an electronics package that analyzes raw data from the analyzer and emits a signal indicating the presence of at least one toxic agent in the water sample.

Optimal investment strategies and hedging of derivatives in the presence of transaction costs (Invited Paper)

NASA Astrophysics Data System (ADS)

Muratore-Ginanneschi, Paolo

2005-05-01

Investment strategies in multiplicative Markovian market models with transaction costs are defined using growth optimal criteria. The optimal strategy is shown to consist in holding the amount of capital invested in stocks within an interval around an ideal optimal investment. The size of the holding interval is determined by the intensity of the transaction costs and the time horizon. The inclusion of financial derivatives in the models is also considered. All the results presented in this contributions were previously derived in collaboration with E. Aurell.

Design and Test of a Closed-Loop FES System for Supporting Function of the Hemiparetic Hand Based on Automatic Detection using the Microsoft Kinect sensor.

PubMed

Simonsen, Daniel; Spaich, Erika G; Hansen, John; Andersen, Ole K

2016-10-26

This paper describes the design of a FES system automatically controlled in a closed loop using a Microsoft Kinect sensor, for assisting both cylindrical grasping and hand opening. The feasibility of the system was evaluated in real-time in stroke patients with hand function deficits. A hand function exercise was designed in which the subjects performed an arm and hand exercise in sitting position. The subject had to grasp one of two differently sized cylindrical objects and move it forward or backwards in the sagittal plane. This exercise was performed with each cylinder with and without FES support. Results showed that the stroke patients were able to perform up to 29% more successful grasps when they were assisted by FES. Moreover, the hand grasp-and-hold and hold-and-release durations were shorter for the smaller of the two cylinders. FES was appropriately timed in more than 95% of all trials indicating successful closed loop FES control. Future studies should incorporate options for assisting forward reaching in order to target a larger group of stroke patients.

Thermal degradation of TiO2 nanotubes on titanium

NASA Astrophysics Data System (ADS)

Shivaram, Anish; Bose, Susmita; Bandyopadhyay, Amit

2014-10-01

The objective of this research was to study thermal degradation behavior of TiO2 nanotubes on titanium (Ti). TiO2 nanotubes were grown via anodization method on commercially pure Ti (Cp-Ti) discs using two different electrolytes, 1 vol. % HF in deionized (DI) water and 1 vol. % HF + 0.5 wt. % NH4F + 10 vol. % DI water in ethylene glycol, to obtain nanotubes with two different lengths, 300 nm and 950 nm keeping the nanotube diameter constant at 100 ± 20 nm. As grown TiO2 nanotubes were subjected to heat treatment to understand thermal degradation as a function of both temperature and hold time. The signs of degradation were observed mainly when amorphous nanotubes started to crystallize, however the crystallization temperature varied based on TiO2 nanotubes length and anodizing condition. Overall, 300 nm nanotubes were thermally stable at least up to 400 °C for 12 h, while the 950 nm long nanotubes show signs of degradation from 400 °C for 6 h only. Clearly, length of nanotubes, heat treatment temperature as well as hold times show influence toward degradation kinetics of TiO2 nanotubes on titanium.

Short communication: effect of homogenization on heat inactivation of Mycobacterium avium subspecies paratuberculosis in milk.

PubMed

Hammer, P; Kiesner, C; Walte, H-G C

2014-01-01

Mycobacterium avium ssp. paratuberculosis (MAP) can be present in cow milk and low numbers may survive high-temperature, short-time (HTST) pasteurization. Although HTST treatment leads to inactivation of at least 5 log10 cycles, it might become necessary to enhance the efficacy of HTST by additional treatments such as homogenization if the debate about the role of MAP in Crohn's disease of humans concludes that MAP is a zoonotic agent. This study aimed to determine whether disrupting the clumps of MAP in milk by homogenization during the heat treatment process would enhance the inactivation of MAP. We used HTST pasteurization in a continuous-flow pilot-plant pasteurizer and evaluated the effect of upstream, downstream, and in-hold homogenization on inactivation of MAP. Reduction of MAP at 72°C with a holding time of 28s was between 3.7 and 6.9 log10 cycles, with an overall mean of 5.5 log10 cycles. None of the 3 homogenization modes applied showed a statistically significant additional effect on the inactivation of MAP during HTST treatment. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Lead recovery and the feasibility of foam glass production from funnel glass of dismantled cathode ray tube through pyrovacuum process.

PubMed

Chen, Mengjun; Zhang, Fu-Shen; Zhu, Jianxin

2009-01-30

Cathode ray tube (CRT) is the first and foremost problem that must be solved in electronic waste disposal, and the key of which lies in the detoxification and reutilization of lead-contained funnel glass. In this study, a novel and effective process for funnel glass of dismantled CRT treatment was developed. The key point of the process was to recover metallic lead from the funnel glass and to prepare foam glass synchronously. Experimental results showed that lead recovery rate increased first with the increase of temperature, carbon adding amount, and holding time, then reached a plateau value, but pressure was on the contrary. The optimum temperature, pressure, carbon adding amount and holding time for lead recovery were 1000 degrees C, 1000 Pa, 5% and 4h, respectively, and the maximum lead recovery rate was 98.6%. In the pyrovacuum process, lead in the funnel glass was firstly detached and changed to PbO, then reduced and evaporated, and was recovered in the form of pure metal with a purity of 99.3%. The residue porous glass was environmentally acceptable for construction application.

Improvement of Electropolishing of 1100 Al Alloy for Solar Thermal Applications

NASA Astrophysics Data System (ADS)

Aguilar-Sierra, Sara María; Echeverría E, Félix

2018-03-01

Aluminum sheets-based mirrors are finding applicability in high-temperature solar concentrating technologies because they are cost-effective, lightweight and have high mechanical properties. Nonetheless, the reflectance percentages obtained by electropolishing are not close to the reflectance values of the currently used evaporated films. Therefore, controlling key factors affecting electropolishing processes became essential in order to achieve highly reflective aluminum surfaces. This study investigated the effect of both the electropolishing process and previous heat treatment on the total reflectance of the AA 1100 aluminum alloy. An acid electrolyte and a modified Brytal process were evaluated. Total reflectance was measured by means of UV-Vis spectrophotometry. Reflectance values higher than 80% at 600 nm were achieved for both electrolytes. Optical microscopy and scanning electron microscopy images showed uneven dissolution for the acid electropolished samples causing a reflectance drop in the 200-450 nm region. The influence of heat treatment, previously to electropolishing, was tested at two different temperatures and various holding times. It was found that reflectance increases around 15% for the heat-treated and electropolished samples versus the non-heat-treated ones. A heat treatment at low temperature combined with a short holding time was enough to improve the sample total reflectance.