46 CFR 44.310 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Assigning Working Freeboards to Hopper Dredges § 44.310 Definitions. Hopper dredge means a self-propelled dredge with an open hold or hopper in the hull of the dredge that receives dredged material. Working...

Coal storage hopper with vibrating screen agitator

DOEpatents

Daw, Charles S.; Lackey, Mack E.; Sy, Ronald L.

1984-01-01

The present invention is directed to a vibrating screen agitator in a coal storage hopper for assuring the uniform feed of coal having sufficient moisture content to effect agglomeration and bridging thereof in the coal hopper from the latter onto a conveyor mechanism. The vibrating screen agitator is provided by a plurality of transversely oriented and vertically spaced apart screens in the storage hopper with a plurality of vertically oriented rods attached to the screens. The rods are vibrated to effect the vibration of the screens and the breaking up of agglomerates in the coal which might impede the uniform flow of the coal from the hopper onto a conveyer.

Coal storage hopper with vibrating-screen agitator

DOEpatents

Daw, C.S.; Lackey, M.E.; Sy, R.L.

1982-04-27

The present invention is directed to a vibrating screen agitator in a coal storage hopper for assuring the uniform feed of coal having sufficient moisture content to effect agglomeration and bridging thereof in the coal hopper from the latter onto a conveyer mechanism. The vibrating scrren agitator is provided by a plurality of transversely oriented and vertically spaced apart screens in the storage hopper with a plurality of vertically oriented rods attached to the screens. The rods are vibrated to effect the vibration of the screens and the breaking up of agglomerates in the coal which might impede the uniform flow of the coal from the hopper onto a conveyer.

Management of mango hopper, Idioscopus clypealis, using chemical insecticides and Neem oil.

PubMed

Adnan, S M; Uddin, M M; Alam, M J; Islam, M S; Kashem, M A; Rafii, M Y; Latif, M A

2014-01-01

An experiment was conducted in Field Laboratory, Department of Entomology at Bangladesh Agricultural University, Mymensingh, during 2013 to manage the mango hopper, Idioscopus clypealis L, using three chemical insecticides, Imidacloprid (0.3%), Endosulfan (0.5%), and Cypermethrin (0.4%), and natural Neem oil (3%) with three replications of each. All the treatments were significantly effective in managing mango hopper in comparison to the control. Imidacloprid showed the highest efficacy in percentage of reduction of hopper population (92.50 ± 9.02) at 72 hours after treatment in case of 2nd spray. It also showed the highest overall percentage of reduction (88.59 ± 8.64) of hopper population and less toxicity to natural enemies including green ant, spider, and lacewing of mango hopper. In case of biopesticide, azadirachtin based Neem oil was found effective against mango hopper as 48.35, 60.15, and 56.54% reduction after 24, 72, and 168 hours of spraying, respectively, which was comparable with Cypermethrin as there was no statistically significant difference after 168 hours of spray. Natural enemies were also higher after 1st and 2nd spray in case of Neem oil.

Management of Mango Hopper, Idioscopus clypealis, Using Chemical Insecticides and Neem Oil

PubMed Central

Adnan, S. M.; Uddin, M. M.; Alam, M. J.; Islam, M. S.; Kashem, M. A.; Rafii, M. Y.; Latif, M. A.

2014-01-01

An experiment was conducted in Field Laboratory, Department of Entomology at Bangladesh Agricultural University, Mymensingh, during 2013 to manage the mango hopper, Idioscopus clypealis L, using three chemical insecticides, Imidacloprid (0.3%), Endosulfan (0.5%), and Cypermethrin (0.4%), and natural Neem oil (3%) with three replications of each. All the treatments were significantly effective in managing mango hopper in comparison to the control. Imidacloprid showed the highest efficacy in percentage of reduction of hopper population (92.50 ± 9.02) at 72 hours after treatment in case of 2nd spray. It also showed the highest overall percentage of reduction (88.59 ± 8.64) of hopper population and less toxicity to natural enemies including green ant, spider, and lacewing of mango hopper. In case of biopesticide, azadirachtin based Neem oil was found effective against mango hopper as 48.35, 60.15, and 56.54% reduction after 24, 72, and 168 hours of spraying, respectively, which was comparable with Cypermethrin as there was no statistically significant difference after 168 hours of spray. Natural enemies were also higher after 1st and 2nd spray in case of Neem oil. PMID:25140344

COKE STORAGE HOPPER LOCATED OUTSIDE THE MALLEABLE FOUNDRY SHOWING LOADING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

COKE STORAGE HOPPER LOCATED OUTSIDE THE MALLEABLE FOUNDRY SHOWING LOADING DEVICE THAT USED A SKIP CAR TO FILL THE HOPPER FROM UNDERGROUND GRAVITY-FED STORAGE AREAS FROM INCOMING RAILROAD CARS. - Stockham Pipe & Fittings Company, 4000 Tenth Avenue North, Birmingham, Jefferson County, AL

46 CFR 174.335 - Watertight doors.

Code of Federal Regulations, 2010 CFR

2010-10-01

... SPECIFIC VESSEL TYPES Hopper Dredges With Working Freeboard Assignments Design § 174.335 Watertight doors. (a) Each hopper dredge must have sliding watertight doors (Class 3) approved under § 170.270 of this... to and including the maximum amount of assumed damage. (b) Each hopper dredge must have sliding...

46 CFR 174.335 - Watertight doors.

Code of Federal Regulations, 2011 CFR

2011-10-01

... SPECIFIC VESSEL TYPES Hopper Dredges With Working Freeboard Assignments Design § 174.335 Watertight doors. (a) Each hopper dredge must have sliding watertight doors (Class 3) approved under § 170.270 of this... to and including the maximum amount of assumed damage. (b) Each hopper dredge must have sliding...

7 CFR 58.212 - Hopper or dump room.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Hopper or dump room. 58.212 Section 58.212 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards....212 Hopper or dump room. A separate room shall be provided for the transfer of bulk dry dairy products...

Gravity flow of powder in a lunar environment. Part 2: Analysis of flow initiation

NASA Technical Reports Server (NTRS)

Pariseau, W. G.

1971-01-01

A small displacement-small strain finite element technique utilizing the constant strain triangle and incremental constitutive equations for elasticplastic (media nonhardening and obeying a Coulomb yield condition) was applied to the analysis of gravity flow initiation. This was done in a V-shaped hopper containing a powder under lunar environmental conditions. Three methods of loading were examined. Of the three, the method of computing the initial state of stress in a filled hopper prior to drawdown, by adding material to the hopper layer by layer, was the best. Results of the analysis of a typical hopper problem show that the initial state of stress, the elastic moduli, and the strength parameters have an important influence on material response subsequent to the opening of the hopper outlet.

Full-scale locomotive dynamic crash testing and correlations : C-39 type locomotive colliding with a loaded hopper car (test 7).

DOT National Transportation Integrated Search

2011-09-01

This report presents the results of a locomotive and three loaded hopper car consist traveling at 29 miles per hour colliding with a stationary consist of 35 loaded hopper cars. The details of test instrumentation, LS-DYNA finite element simulation, ...

46 CFR 174.330 - Jettisoning of spoil.

Code of Federal Regulations, 2010 CFR

2010-10-01

... PERTAINING TO SPECIFIC VESSEL TYPES Hopper Dredges With Working Freeboard Assignments Calculations § 174.330 Jettisoning of spoil. (a) When doing the calculations required by § 174.310 for a hopper dredge with bottom... calculations required by § 174.310 for a hopper dredge with a split hull, it may be assumed that the spoil is...

46 CFR 174.330 - Jettisoning of spoil.

Code of Federal Regulations, 2011 CFR

2011-10-01

... PERTAINING TO SPECIFIC VESSEL TYPES Hopper Dredges With Working Freeboard Assignments Calculations § 174.330 Jettisoning of spoil. (a) When doing the calculations required by § 174.310 for a hopper dredge with bottom... calculations required by § 174.310 for a hopper dredge with a split hull, it may be assumed that the spoil is...

Hopper Growth of Salt Crystals.

PubMed

Desarnaud, Julie; Derluyn, Hannelore; Carmeliet, Jan; Bonn, Daniel; Shahidzadeh, Noushine

2018-06-07

The growth of hopper crystals is observed for many substances, but the mechanism of their formation remains ill understood. Here we investigate their growth by performing evaporation experiments on small volumes of salt solutions. We show that sodium chloride crystals that grow very fast from a highly supersaturated solution form a peculiar form of hopper crystal consisting of a series of connected miniature versions of the original cubic crystal. The transition between cubic and such hopper growth happens at a well-defined supersaturation where the growth rate of the cubic crystal reaches a maximum (∼6.5 ± 1.8 μm/s). Above this threshold, the growth rate varies as the third power of supersaturation, showing that a new mechanism, controlled by the maximum speed of surface integration of new molecules, induces the hopper growth of cubic crystals in cascade.

Hopper Flow: Experiments and Simulation

NASA Astrophysics Data System (ADS)

Li, Zhusong; Shattuck, Mark

2013-03-01

Jamming and intermittent granular flow are important problems in industry, and the vertical hopper is a canonical example. Clogging of granular hoppers account for significant losses across many industries. We use realistic DEM simulations of gravity driven flow in a hopper to examine flow and jamming of 2D disks and compare with identical companion experiments. We use experimental data to validate simulation parameters and the form of the inter particle force law. We measure and compare flow rate, emptying times, jamming statistics, and flow fields as a function of opening angle and opening size in both experiment and simulations. Suppored by: NSF-CBET-0968013

77 FR 21797 - Hopper Mountain, Bitter Creek, and Blue Ridge National Wildlife Refuges, Ventura, Kern, San Luis...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-11

..., and visitor and volunteer opportunities. Alternatives for Blue Ridge NWR Under Alternative B...-FF08R00000] Hopper Mountain, Bitter Creek, and Blue Ridge National Wildlife Refuges, Ventura, Kern, San Luis... Conservation Plan (CCP) and Environmental Assessment (EA) for the Hopper Mountain, Bitter Creek, and Blue Ridge...

75 FR 17430 - Hopper Mountain, Bitter Creek, and Blue Ridge National Wildlife Refuges, Kern, San Luis Obispo...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-06

...] Hopper Mountain, Bitter Creek, and Blue Ridge National Wildlife Refuges, Kern, San Luis Obispo, Tulare... Wildlife Refuges (NWRs) located in Kern, San Luis Obispo, Tulare, and Ventura counties of California. We... developing a CCP for Hopper Mountain, Bitter Creek, and Blue Ridge NWRs in Kern, San Luis Obispo, Tulare, and...

Elevation (typical EBT Coal Hopper Car) with scale. 3 Bay ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Elevation (typical EBT Coal Hopper Car) with scale. 3 Bay Steel Hopper Car with side extensions raising coal carrying capacity to 80,000 pounds. Note cars on either side lack extensions limiting their coal capacity to 70,000 pounds - East Broad Top Railroad & Coal Company, State Route 994, West of U.S. Route 522, Rockhill Furnace, Huntingdon County, PA

46 CFR 97.15-75 - Test of inflatable hopper gate seals on Great Lakes bulk dry cargo vessels.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Test of inflatable hopper gate seals on Great Lakes bulk... (CONTINUED) CARGO AND MISCELLANEOUS VESSELS OPERATIONS Tests, Drills, and Inspections § 97.15-75 Test of... ensure that the inflatable hopper gate seals installed on vessels required to meet the damage stability...

46 CFR 97.15-75 - Test of inflatable hopper gate seals on Great Lakes bulk dry cargo vessels.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Test of inflatable hopper gate seals on Great Lakes bulk... (CONTINUED) CARGO AND MISCELLANEOUS VESSELS OPERATIONS Tests, Drills, and Inspections § 97.15-75 Test of... ensure that the inflatable hopper gate seals installed on vessels required to meet the damage stability...

46 CFR 97.15-75 - Test of inflatable hopper gate seals on Great Lakes bulk dry cargo vessels.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Test of inflatable hopper gate seals on Great Lakes bulk... (CONTINUED) CARGO AND MISCELLANEOUS VESSELS OPERATIONS Tests, Drills, and Inspections § 97.15-75 Test of... ensure that the inflatable hopper gate seals installed on vessels required to meet the damage stability...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pickenheim, B.; Hansen, E.; Leishear, R.

A 10-inch READCO mixer is used for mixing the premix (45 (wt%) fly ash, 45 wt% slag, and 10 wt% portland cement) with salt solution in the Saltstone Production Facility (SPF). The Saltstone grout free falls into the grout hopper which feeds the suction line leading to the Watson SPX 100 duplex hose pump. The Watson SPX 100 pumps the grout through approximately 1500 feet of piping prior to being discharged into the Saltstone Disposal Facility (SDF) vaults. The existing grout hopper has been identified by the Saltstone Enhanced Low Activity Waste Disposal (ELAWD) project for re-design. The current nominalmore » working volume of this hopper is 12 gallons and does not permit handling an inadvertent addition of excess dry feeds. Saltstone Engineering has proposed a new hopper tank that will have a nominal working volume of 300 gallons and is agitated with a mechanical agitator. The larger volume hopper is designed to handle variability in the output of the READCO mixer and process upsets without entering set back during processing. The objectives of this task involve scaling the proposed hopper design and testing the scaled hopper for the following processing issues: (1) The effect of agitation on radar measurement. Formation of a vortex may affect the ability to accurately measure the tank level. The agitator was run at varying speeds and with varying grout viscosities to determine what parameters cause vortex formation and whether measurement accuracy is affected. (2) A dry feeds over addition. Engineering Calculating X-ESR-Z-00017 1 showed that an additional 300 pounds of dry premix added to a 300 gallon working volume would lower the water to premix ratio (W/P) from the nominal 0.60 to 0.53 based on a Salt Waste Processing Facility (SWPF) salt simulant. A grout with a W/P of 0.53 represents the upper bound of grout rheology that could be processed at the facility. A scaled amount of dry feeds will be added into the hopper to verify that this is a recoverable situation. (3) The necessity of baffles in the hopper. The preference of the facility is not to have baffles in the hopper; however, if the initial testing indicates inadequate agitation or difficulties with the radar measurement, baffles will be tested.« less

39. VIEW OF HOPPERS LOCATED AT THE BOTTOM OF COTTRELL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

39. VIEW OF HOPPERS LOCATED AT THE BOTTOM OF COTTRELL PRECIPITATOR CHAMBERS. PARTICLES REMOVED FROM THE FLUE GAS STREAM WERE DISCHARGED INTO THE VACUUM ASH COLLECTION PIPES LOCATED BELOW THE HOPPERS. THE COTTRELL PRECIPITATORS WERE LOCATED ON THE OUTSIDE WALL OF THE EAST BOILER ROOM. REFER TO PHOTOCOPY CT-142A-15. - New York, New Haven & Hartford Railroad, Cos Cob Power Plant, Sound Shore Drive, Greenwich, Fairfield County, CT

Coal Handling.

DTIC Science & Technology

1981-04-01

the coal in a conical shape pile. 6 _7 7.1.2 TELESCOPING CHUTES Telescoping chutes are also fed by a conveyor . The chute has several sections that can...track hopper. Hopper belt feeders feed a conveyor then to another conveyor thru a belt scale. Onto a transfer hopper then to a stacker reclaimer. The...16.7.1 McNally Pittsburg Mfg. Corp. 16.7.2 Stephens - Adamson, Inc. 16.7.3 Heyl & Oatterson, Inc. 16.8 Telescopic Chutes 16.8.1 Midwest Conveyor Co

Small Body Hopper Mobility Concepts

NASA Technical Reports Server (NTRS)

Howe, A. Scott; Gernhardt, Michael L.; Lee, Dave E.; Crues, E. Zack; Dexter, Dan E.; Abercromby, Andrew F. J.; Chappell, Steve P.; Nguyen, Hung T.

2015-01-01

A propellant-saving hopper mobility system was studied that could help facilitate the exploration of small bodies such as Phobos for long-duration human missions. The NASA Evolvable Mars Campaign (EMC) has proposed a mission to the moons of Mars as a transitional step for eventual Mars surface exploration. While a Mars transit habitat would be parked in High-Mars Orbit (HMO), crew members would visit the surface of Phobos multiple times for up to 14 days duration (up to 50 days at a time with logistics support). This paper describes a small body surface mobility concept that is capable of transporting a small, two-person Pressurized Exploration Vehicle (PEV) cabin to various sites of interest in the low-gravity environment. Using stored kinetic energy between bounces, a propellant-saving hopper mobility system can release the energy to vector the vehicle away from the surface in a specified direction. Alternatively, the stored energy can be retained for later use while the vehicle is stationary in respect to the surface. The hopper actuation was modeled using a variety of launch velocities, and the hopper mobility was evaluated using NASA Exploration Systems Simulations (NExSyS) for transit between surface sites of interest. A hopper system with linear electromagnetic motors and mechanical spring actuators coupled with Control Moment Gyroscope (CMG) for attitude control will use renewable electrical power, resulting in a significant propellant savings.

Larry car for a coking oven battery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Corry, D.B.

A larry car (3) for transporting a charge of pre-heated coal along the top of a battery of coke ovens, from a storage installation including a group of metering bins (1) at one or more filling stations above the battery, to a corresponding group of charge holes for the oven chamber to be charged, the car including a corresponding group of coal transfer hoppers (4) each having valved inlet and discharge apertures (5,21), a sealed connection (2) between each metering bin and transfer hopper, an inert gas reservoir (10) connectable via a valved manifold (13,14) to each transfer hopper, amore » valved connection (7,8,9) for charging the reservoir, and a valved connection (15,16,17) to permit dusty gas to be displaced into the storage bunkers, and control means for the various valved connections to maintain continuous isolation of the interior of each transfer hopper from the atmosphere, to permit dust-laden gases to escape into the storage installation, and to cause inert medium to displace coal discharged from the transfer hoppers.« less

Outflow and clogging of shape-anisotropic grains in hoppers with small apertures.

PubMed

Ashour, A; Wegner, S; Trittel, T; Börzsönyi, T; Stannarius, R

2017-01-04

Outflow of granular material through a small orifice is a fundamental process in many industrial fields, for example in silo discharge, and in everyday's life. Most experimental studies of the dynamics have been performed so far with monodisperse disks in two-dimensional (2D) hoppers or spherical grains in 3D. We investigate this process for shape-anisotropic grains in 3D hoppers and discuss the role of size and shape parameters on avalanche statistics, clogging states, and mean flow velocities. It is shown that an increasing aspect ratio of the grains leads to lower flow rates and higher clogging probabilities compared to spherical grains. On the other hand, the number of grains forming the clog is larger for elongated grains of comparable volumes, and the long axis of these blocking grains is preferentially aligned towards the center of the orifice. We find a qualitative transition in the hopper discharge behavior for aspect ratios larger than ≈6. At still higher aspect ratios >8-12, the outflowing material leaves long vertical holes in the hopper that penetrate the complete granular bed. This changes the discharge characteristics qualitatively.

Sodium chloride crystallization from thin liquid sheets, thick layers, and sessile drops in microgravity

NASA Astrophysics Data System (ADS)

Fontana, Pietro; Pettit, Donald; Cristoforetti, Samantha

2015-10-01

Crystallization from aqueous sodium chloride solutions as thin liquid sheets, 0.2-0.7 mm thick, with two free surfaces supported by a wire frame, thick liquid layers, 4-6 mm thick, with two free surfaces supported by metal frame, and hemispherical sessile drops, 20-32 mm diameter, supported by a flat polycarbonate surface or an initially flat gelatin film, were carried out under microgravity on the International Space Station (ISS). Different crystal morphologies resulted based on the fluid geometry: tabular hoppers, hopper cubes, circular [111]-oriented crystals, and dendrites. The addition of polyethylene glycol (PEG-3350) inhibited the hopper growth resulting in flat-faced surfaces. In sessile drops, 1-4 mm tabular hopper crystals formed on the free surface and moved to the fixed contact line at the support (polycarbonate or gelatin) self-assembling into a shell. Ring formation created by sessile drop evaporation to dryness was observed but with crystals 100 times larger than particles in terrestrially formed coffee rings. No hopper pyramids formed. By choosing solution geometries offered by microgravity, we found it was possible to selectively grow crystals of preferred morphologies.

46 CFR 174.300 - Specific applicability.

Code of Federal Regulations, 2010 CFR

2010-10-01

... PERTAINING TO SPECIFIC VESSEL TYPES Hopper Dredges With Working Freeboard Assignments § 174.300 Specific applicability. This subpart applies to each self-propelled hopper dredge for which a working freeboard...

46 CFR 174.300 - Specific applicability.

Code of Federal Regulations, 2011 CFR

2011-10-01

... PERTAINING TO SPECIFIC VESSEL TYPES Hopper Dredges With Working Freeboard Assignments § 174.300 Specific applicability. This subpart applies to each self-propelled hopper dredge for which a working freeboard...

46 CFR 44.300 - Applicability.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Rules for Assigning Working Freeboards to Hopper Dredges § 44.300 Applicability. This subpart applies to each self-propelled hopper dredge— (a) For which a working freeboard assignment is desired after...

46 CFR 44.300 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Rules for Assigning Working Freeboards to Hopper Dredges § 44.300 Applicability. This subpart applies to each self-propelled hopper dredge— (a) For which a working freeboard assignment is desired after...

Design Study for a Mars Geyser Hopper

NASA Technical Reports Server (NTRS)

Landis, Geoffrey A.; Oleson, Steven J.; McGuire, Melissa

2012-01-01

The Mars Geyser Hopper is a design reference missions (DRMs) for a Discovery-class spacecraft using Advanced Stirling Radioisotope Generator (ASRG) power source. The Geyser Hopper is a mission concept that will investigate the springtime carbon-dioxide geysers found in regions around the south pole of Mars. The Geyser Hopper design uses Phoenix heritage systems and approach, but uses a single ASRG as the power source, rather than twin solar arrays, and is designed to last over a one-year stay on the South Pole. The spacecraft will land at a target landing area near the south pole of Mars, and have the ability to "hop" after a summertime landing to reposition itself close to a geyser site, and wait through the winter until the first sunlight of spring to witness first-hand the geyser phenomenon.

Dredging Research Program: Practices and Problems Associated with Economic Loading and Overflow of Dredge Hoppers and Scows

DTIC Science & Technology

1990-10-01

Services No. EB687D020, 20 January 1987, as a part of the Dredging Research Program (DRP), managed by the WES Coastal Engineering Research Center (CERC...with the bottom. The bottom sediments are entrained with the ambient water, lifted hydraulically by the dredge pumps, and discharged into the hop - pers...in a hopper. Some of these are particle size, hopper capacity and opening area, settling velocity, flow velocity in the hop - per, inflow

Simulation of 2D Granular Hopper Flow

NASA Astrophysics Data System (ADS)

Li, Zhusong; Shattuck, Mark

2012-02-01

Jamming and intermittent granular flow are big problems in industry, and the vertical hopper is a canonical example of these difficulties. We simulate gravity driven flow and jamming of 2D disks in a vertical hopper and compare with identical companion experiments presented in this session. We measure and compare the flow rate and probability for jamming as a function of particle properties and geometry. We evaluate the ability of standard Hertz-Mindlin contact mode to quantitatively predict the experimental flow.

46 CFR 174.340 - Collision bulkhead.

Code of Federal Regulations, 2010 CFR

2010-10-01

... PERTAINING TO SPECIFIC VESSEL TYPES Hopper Dredges With Working Freeboard Assignments Design § 174.340 Collision bulkhead. Each hopper dredge must have a collision bulkhead that is located not less than 5...

46 CFR 174.340 - Collision bulkhead.

Code of Federal Regulations, 2011 CFR

2011-10-01

... PERTAINING TO SPECIFIC VESSEL TYPES Hopper Dredges With Working Freeboard Assignments Design § 174.340 Collision bulkhead. Each hopper dredge must have a collision bulkhead that is located not less than 5...

46 CFR 174.305 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... SPECIFIC VESSEL TYPES Hopper Dredges With Working Freeboard Assignments § 174.305 Definitions. Hopper dredge has the same meaning as contained in § 44.310 of this chapter. Length has the same meaning as...

46 CFR 174.305 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... SPECIFIC VESSEL TYPES Hopper Dredges With Working Freeboard Assignments § 174.305 Definitions. Hopper dredge has the same meaning as contained in § 44.310 of this chapter. Length has the same meaning as...

VIEW FROM CHARGING FLOOR LOOKING EAST AT COAL HOPPER, AND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

VIEW FROM CHARGING FLOOR LOOKING EAST AT COAL HOPPER, AND PHYSICAL REMAINS OF GAS PRODUCER SYSTEM. - Pittsburgh Steel Company, Monessen Works, Open Hearth Plant, Donner Avenue, Monessen, Westmoreland County, PA

8. VIEW OF BATCHING HOPPER ON SERVICE FLOOR OF FURNACE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

8. VIEW OF BATCHING HOPPER ON SERVICE FLOOR OF FURNACE AISLE IN BOP SHOP LOOKING SOUTH. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

Looking south at the ash disposal hoppers for boilers numbers ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Looking south at the ash disposal hoppers for boilers numbers 1 through 6. - Wheeling-Pittsburgh Steel Corporation, Allenport Works, Boiler House, Route 88 on West bank of Monongahela River, Allenport, Washington County, PA

On the computation of steady Hopper flows. II: von Mises materials in various geometries

NASA Astrophysics Data System (ADS)

Gremaud, Pierre A.; Matthews, John V.; O'Malley, Meghan

2004-11-01

Similarity solutions are constructed for the flow of granular materials through hoppers. Unlike previous work, the present approach applies to nonaxisymmetric containers. The model involves ten unknowns (stresses, velocity, and plasticity function) determined by nine nonlinear first order partial differential equations together with a quadratic algebraic constraint (yield condition). A pseudospectral discretization is applied; the resulting problem is solved with a trust region method. The important role of the hopper geometry on the flow is illustrated by several numerical experiments of industrial relevance.

Microscopic analysis of Hopper flow with ellipsoidal particles

NASA Astrophysics Data System (ADS)

Liu, Sida; Zhou, Zongyan; Zou, Ruiping; Pinson, David; Yu, Aibing

2013-06-01

Hoppers are widely used in process industries. With such widespread application, difficulties in achieving desired operational behaviors have led to extensive experimental and mathematical studies in the past decades. Particularly, the discrete element method has become one of the most important simulation tools for design and analysis. So far, most studies are on spherical particles for computational convenience. In this work, ellipsoidal particles are used as they can represent a large variation of particle shapes. Hopper flow with ellipsoidal particles is presented highlighting the effect of particle shape on the microscopic properties.

4. FLUX STORAGE HOPPERS ON THE WEIGHING FLOOR OF THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. FLUX STORAGE HOPPERS ON THE WEIGHING FLOOR OF THE FURNACE AISLE IN THE BOP SHOP LOOKING SOUTHWEST. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

Safety control circuit for a neutronic reactor

DOEpatents

Ellsworth, Howard C.

2004-04-27

A neutronic reactor comprising an active portion containing material fissionable by neutrons of thermal energy, means to control a neutronic chain reaction within the reactor comprising a safety device and a regulating device, a safety device including means defining a vertical channel extending into the reactor from an aperture in the upper surface of the reactor, a rod containing neutron-absorbing materials slidably disposed within the channel, means for maintaining the safety rod in a withdrawn position relative to the active portion of the reactor including means for releasing said rod on actuation thereof, a hopper mounted above the active portion of the reactor having a door disposed at the bottom of the hopper opening into the vertical channel, a plurality of bodies of neutron-absorbing materials disposed within the hopper, and means responsive to the failure of the safety rod on actuation thereof to enter the active portion of the reactor for opening the door in the hopper.

6. FLUX WEIGH HOPPERS AND SCALES ON THE BATCHING FLOOR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. FLUX WEIGH HOPPERS AND SCALES ON THE BATCHING FLOOR OF THE FURNACE AISLE IN THE BOP SHOP LOOKING SOUTHWEST. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

7. NORTHWEST VIEW OF FLUX CONVEYORS FEEDING BATCH HOPPERS ON ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. NORTHWEST VIEW OF FLUX CONVEYORS FEEDING BATCH HOPPERS ON THE BATCHING FLOOR OF THE FURNACE AISLE IN THE BOP SHOP. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

27. INTERIOR OF UTILITY ROOM SHOWING ELECTRICAL JUNCTION CABINET, HOPPER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

27. INTERIOR OF UTILITY ROOM SHOWING ELECTRICAL JUNCTION CABINET, HOPPER WINDOW, OPEN DOOR TO KITCHEN NO. 2, AND METAL SINK. VIEW TO SOUTHWEST. - Bishop Creek Hydroelectric System, Plant 6, Cashbaugh-Kilpatrick House, Bishop Creek, Bishop, Inyo County, CA

4. Hopper was used to collect bark from the Chipper ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. Hopper was used to collect bark from the Chipper Building. Processed bark was loaded into trucks for disposal at a pit on site. - Pacific Creosoting Plant, Log Peeling Operation, 5350 Creosote Place, Northeast, Bremerton, Kitsap County, WA

Inside the covered hopper car loading dock at railroad level, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Inside the covered hopper car loading dock at railroad level, looking east from the 1945 elevator into the 1913 elevator, control for the railroad car puller in background - Stewart Company Grain Elevator, 16 West Carson Street, Pittsburgh, Allegheny County, PA

VIEW OF SEMIDISMANTLED HOPPER CAR ON THE ORE TRESTLE FACING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

VIEW OF SEMI-DISMANTLED HOPPER CAR ON THE ORE TRESTLE FACING NORTHWEST WITH OPEN HEARTH BUILDING IN THE BACKGROUND AND THE INGOT MOLD CONDITIONING BUILDING TO THE RIGHT. - Pittsburgh Steel Company, Monessen Works, Open Hearth Plant, Donner Avenue, Monessen, Westmoreland County, PA

15. VIEW OF COAL TRESTLE LOOKING NORTHEAST. COAL DUMPED FROM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

15. VIEW OF COAL TRESTLE LOOKING NORTHEAST. COAL DUMPED FROM HOPPER CARS COULD BE CRUSHED AND LOADED ON A CONVEYOR THAT PARALLELED THE TRACK TO THE EAST (LEFT) AND CARRIED IT TO A 1000 TON BUNKER LOCATED ON THE NORTH SIDE OF THE EAST BOILER ROOM. COAL COULD ALSO GO THROUGH THE CRUSHER AND BE DIVERTED TO THE CONVEYOR SHOWN IN THE LEFT FOREGROUND. COAL PILES FORMED UNDER THE CONVEYOR WOULD BE MOVED AND SHAPED BY BULLDOZER. A GROUND LEVEL HOPPER WAS LOCATED TO THE RIGHT OF THE SLOPING HOUSING WHICH EXTENDS FROM THE SOUTH SIDE OF THE COAL TRESTLE. THIS HOPPER FED A CONVEYOR LOCATED WITHIN THE SLOPING HOUSING. COAL DROPPED INTO THE HOPPER WOULD BE CONVEYED INTO THE CRUSHER UNDER THE TRESTLE AND THEN DIVERTED TO THE CONVEYOR WHICH LOADED THE 1000 TON BUNKER. THE COAL HANDLING SYSTEM WAS DESIGNED BY GIBBS AND HILL IN 1947. - New York, New Haven & Hartford Railroad, Cos Cob Power Plant, Sound Shore Drive, Greenwich, Fairfield County, CT

Variability of bulk density of distillers dried grains with solubles (DDGS) during gravity-driven discharge.

PubMed

Clementson, C L; Ileleji, K E

2010-07-01

Loading railcars with consistent tonnage has immense cost implications for the shipping of distillers' dried grains with soluble (DDGS) product. Therefore, this study was designed to investigate the bulk density variability of DDGS during filling of railcar hoppers. An apparatus was developed similar to a spinning riffler sampler in order to simulate the filling of railcars at an ethanol plant. There was significant difference (P<0.05) between the initial and final measures of bulk density and particle size as the hoppers were emptied in both mass and funnel flow patterns. Particle segregation that takes place during filling of hoppers contributed to the bulk density variation and was explained by particle size variation. This phenomenon is most likely the same throughout the industry and an appropriate sampling procedure should be adopted for measuring the bulk density of DDGS stored silos or transported in railcar hoppers. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Urban hopper.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xavier, Patrick Gordon; Feddema, John Todd; Little, Charles Quentin

2010-03-01

Hopping robots provide the possibility of breaking the link between the size of a ground vehicle and the largest obstacle that it can overcome. For more than a decade, DARPA and Sandia National Laboratories have been developing small-scale hopping robot technology, first as part of purely hopping platforms and, more recently, as part of platforms that are capable of both wheeled and hopping locomotion. In this paper we introduce the Urban Hopper robot and summarize its capabilities. The advantages of hopping for overcoming certain obstacles are discussed. Several configurations of the Urban Hopper are described, as are intelligent capabilities ofmore » the system. Key challenges are discussed.« less

46 CFR 174.320 - Damage survival.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Damage survival. 174.320 Section 174.320 Shipping COAST... SPECIFIC VESSEL TYPES Hopper Dredges With Working Freeboard Assignments Calculations § 174.320 Damage survival. A hopper dredge survives assumed damage if it meets the following conditions: (a) The maximum...

46 CFR 174.320 - Damage survival.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 7 2012-10-01 2012-10-01 false Damage survival. 174.320 Section 174.320 Shipping COAST... SPECIFIC VESSEL TYPES Hopper Dredges With Working Freeboard Assignments Calculations § 174.320 Damage survival. A hopper dredge survives assumed damage if it meets the following conditions: (a) The maximum...

46 CFR 174.320 - Damage survival.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 7 2013-10-01 2013-10-01 false Damage survival. 174.320 Section 174.320 Shipping COAST... SPECIFIC VESSEL TYPES Hopper Dredges With Working Freeboard Assignments Calculations § 174.320 Damage survival. A hopper dredge survives assumed damage if it meets the following conditions: (a) The maximum...

7 CFR 58.710 - Fillers.

Code of Federal Regulations, 2010 CFR

2010-01-01

... strainer should be installed between the cooker and the filler. The hoppers of all filters shall be covered but the cover may have sight ports. If necessary, the hopper may have an agitator to prevent buildup... measurements. Product contact surfaces shall be of stainless steel or other corrosion resistant material...

Lunar, Cislunar, Near/Farside Laser Retroreflectors for the Accurate: Positioning of Landers/Rovers/Hoppers/Orbiters, Commercial Georeferencing, Test of Relativistic Gravity, and Metrics of the Lunar Interior

NASA Astrophysics Data System (ADS)

Dell'Agnello, S.; Currie, D.; Ciocci, E.; Contessa, S.; Delle Monache, G.; March, R.; Martini, M.; Mondaini, C.; Porcelli, L.; Salvatori, L.; Tibuzzi, M.; Bianco, G.; Vittori, R.; Chandler, J.; Murphy, T.; Maiello, M.; Petrassi, M.; Lomastro, A.

2017-10-01

We developed next-generation lunar, cislunar, near/farside laser retroreflectors for the improved/accurate: Positioning of landers/rovers/hoppers/orbiters, commercial georeferencing, test of relativistic gravity, and metrics of the lunar interior.

46 CFR 174.310 - General.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Accommodation spaces 0.95 Consumable liquid tanks 0.00 or 0.95—whichever results in the more disabling condition...: (1) The hoppers are full of seawater; (2) The permeability of flooded spaces is as provided by Table... the calculations required by this section: (1) Dredged spoil in the hopper is a homogeneous liquid...

46 CFR 174.310 - General.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Accommodation spaces 0.95 Consumable liquid tanks 0.00 or 0.95—whichever results in the more disabling condition...: (1) The hoppers are full of seawater; (2) The permeability of flooded spaces is as provided by Table... the calculations required by this section: (1) Dredged spoil in the hopper is a homogeneous liquid...

46 CFR 174.310 - General.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Accommodation spaces 0.95 Consumable liquid tanks 0.00 or 0.95—whichever results in the more disabling condition...: (1) The hoppers are full of seawater; (2) The permeability of flooded spaces is as provided by Table... the calculations required by this section: (1) Dredged spoil in the hopper is a homogeneous liquid...

46 CFR 174.310 - General.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Accommodation spaces 0.95 Consumable liquid tanks 0.00 or 0.95—whichever results in the more disabling condition...: (1) The hoppers are full of seawater; (2) The permeability of flooded spaces is as provided by Table... the calculations required by this section: (1) Dredged spoil in the hopper is a homogeneous liquid...

46 CFR 174.310 - General.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Accommodation spaces 0.95 Consumable liquid tanks 0.00 or 0.95—whichever results in the more disabling condition...: (1) The hoppers are full of seawater; (2) The permeability of flooded spaces is as provided by Table... the calculations required by this section: (1) Dredged spoil in the hopper is a homogeneous liquid...

7 CFR 58.228 - Dump hoppers, screens, mixers and conveyors.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AND STANDARDS UNDER THE AGRICULTURAL MARKETING ACT OF 1946 AND THE EGG PRODUCTS INSPECTION ACT... DAIRY PRODUCTS 1 General Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Equipment and Utensils § 58.228 Dump hoppers, screens, mixers and conveyors. The product contact...

Spissistilus festinus reovirus: a novel, unassigned species of the family Reoviridae infecting the three-cornered alfalfa hopper

USDA-ARS?s Scientific Manuscript database

A complex set of double stranded RNAs (dsRNA) were isolated from threecornered alfalfa hopper (Spissistilus festinus), a plant-feeding hemipteran insect pest. A subset of these dsRNAs constitute the genome of a novel, unassigned reovirus designated as Spissistilus festinus reovirus (SpFRV). Phylogen...

Microfluidic Bead Suspension Hopper

PubMed Central

2014-01-01

Many high-throughput analytical platforms, from next-generation DNA sequencing to drug discovery, rely on beads as carriers of molecular diversity. Microfluidic systems are ideally suited to handle and analyze such bead libraries with high precision and at minute volume scales; however, the challenge of introducing bead suspensions into devices before they sediment usually confounds microfluidic handling and analysis. We developed a bead suspension hopper that exploits sedimentation to load beads into a microfluidic droplet generator. A suspension hopper continuously delivered synthesis resin beads (17 μm diameter, 112,000 over 2.67 h) functionalized with a photolabile linker and pepstatin A into picoliter-scale droplets of an HIV-1 protease activity assay to model ultraminiaturized compound screening. Likewise, trypsinogen template DNA-coated magnetic beads (2.8 μm diameter, 176,000 over 5.5 h) were loaded into droplets of an in vitro transcription/translation system to model a protein evolution experiment. The suspension hopper should effectively remove any barriers to using suspensions as sample inputs, paving the way for microfluidic automation to replace robotic library distribution. PMID:24761972

Response to perturbations for granular flow in a hopper

NASA Astrophysics Data System (ADS)

Wambaugh, John F.; Behringer, Robert P.; Matthews, John V.; Gremaud, Pierre A.

2007-11-01

We experimentally investigate the response to perturbations of circular symmetry for dense granular flow inside a three-dimensional right-conical hopper. These experiments consist of particle tracking velocimetry for the flow at the outer boundary of the hopper. We are able to test commonly used constitutive relations and observe granular flow phenomena that we can model numerically. Unperturbed conical hopper flow has been described as a radial velocity field with no azimuthal component. Guided by numerical models based upon continuum descriptions, we find experimental evidence for secondary, azimuthal circulation in response to perturbation of the symmetry with respect to gravity by tilting. For small perturbations we can discriminate between constitutive relations, based upon the agreement between the numerical predictions they produce and our experimental results. We find that the secondary circulation can be suppressed as wall friction is varied, also in agreement with numerical predictions. For large tilt angles we observe the abrupt onset of circulation for parameters where circulation was previously suppressed. Finally, we observe that for large tilt angles the fluctuations in velocity grow, independent of the onset of circulation.

Variation in bacterial endosymbionts associated with the date palm hopper, Ommatissus lybicus populations.

PubMed

Karimi, S; Izadi, H; Askari Seyahooei, M; Bagheri, A; Khodaygan, P

2018-04-01

The date palm hopper, Ommatissus lybicus, is a key pest of the date palm, which is expected to be comprised of many allopatric populations. The current study was carried out to determine bacterial endosymbiont diversity in the different populations of this pest. Ten date palm hopper populations were collected from the main date palm growing regions in Iran and an additional four samples from Pakistan, Oman, Egypt and Tunisia for detection of primary and secondary endosymbionts using polymerase chain reaction (PCR) assay with their specific primers. The PCR products were directly sequenced and edited using SeqMan software. The consensus sequences were subjected to a BLAST similarity search. The results revealed the presence of 'Candidatus Sulcia muelleri' (primary endosymbiont) and Wolbachia, Arsenophonus and Enterobacter (secondary endosymbionts) in all populations. This assay failed to detect 'Candidatus Nasuia deltocephalinicola' and Serratia in these populations. 'Ca. S. muelleri' exhibited a 100% infection frequency in populations and Wolbachia, Arsenophonus and Enterobacter demonstrated 100, 93.04 and 97.39% infection frequencies, respectively. The infection rate of Arsenophonus and Enterobacter ranged from 75 to 100% and 62.5 to 100%, respectively, in different populations of the insect. The results demonstrated multiple infections by 'Ca. Sulcia muelleri', Wolbachia, Arsenophonus and Enterobacter in the populations and may suggest significant roles for these endosymbionts on date palm hopper population fitness. This study provides an insight to endosymbiont variation in the date palm hopper populations; however, further investigation is needed to examine how these endosymbionts may affect host fitness.

The Mars Hopper: Development, Simulation and Experimental Validation of a Radioisotope Exploration Probe for the Martian Surface

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nathan D. Jerred; Spencer Cooley; Robert C. O'Brien

An advanced exploration probe has been proposed by the Center for Space Nuclear Research (CSNR) to acquire detailed data from the Martian surface and subsurface, ‘hop’ large distances to multiple sites in short periods of time and perform this task repeatedly. Although several similar flying vehicles have been proposed utilizing various power sources and complex designs, e.g. solar-electric and chemical-based, the CSNR’s Mars Hopper is based on a radioisotope thermal rocket (RTR) concept. The Mars Hopper’s design relies on the high specific energies [J/kg] of radioisotopes and enhances their low specific power [W/kg] through the use of a thermal capacitancemore » material to store thermal energy over time. During operation, the RTR transfers the stored thermal energy to a flowing gas, which is then expanded through a converging-diverging nozzle, producing thrust. Between flights, the platform will have ample time to perform in-depth science at each location while the propellant tanks and thermal capacitor recharge. Recharging the propellant tanks is accomplished by sublimation freezing of the ambient CO2 atmosphere with a cryocooler, followed by heating and pressurization to yield a liquid storage state. The proposed Mars Hopper will undergo a ballistic flight, consuming the propellant in both ascent and descent, and by using multiple hopper platforms, information can be gathered on a global scale, enabling better resource resolution and providing valuable information for a possible Mars sample-return mission. The CSNR, collaborating with the Idaho National Laboratory (INL) and three universities (University of Idaho, Utah State University and Oregon State University), has identified key components and sub-systems necessary for the proposed hopper. Current project activities include the development of a lab-scale prototypic Mars Hopper and test facility, along with computational fluid dynamics (CFD)/thermal-hydraulic models to yield a better understanding of the heat transfer process and complex nature of turbulent CO2 flow. Laboratory experimentation will aid design iterations and the development of both tethered and free-flying terrestrial hoppers that utilize an electrically heated core. The knowledge base acquired from these activities will refine the Mars Hopper’s future performance and optimize the RTR core components prior to constructing the final design.« less

3D-Modeling of deformed halite hopper crystals: Object based image analysis and support vector machine, a first evaluation

NASA Astrophysics Data System (ADS)

Leitner, Christoph; Hofmann, Peter; Marschallinger, Robert

2014-05-01

Halite hopper crystals are thought to develop by displacive growth in unconsolidated mud (Gornitz & Schreiber, 1984). The Alpine Haselgebirge, but also e.g. the salt deposits of the Rhine graben (mined at the beginning of the 20th century), comprise hopper crystals with shapes of cuboids, parallelepipeds and rhombohedrons (Görgey, 1912). Obviously, they deformed under oriented stress, which had been tried to reconstruct with respect to the sedimentary layering (Leitner et al., 2013). In the present work, deformed halite hopper crystals embedded in mudrock were automated reconstructed. Object based image analysis (OBIA) has been used successfully in remote sensing for 2D images before. The present study represents the first time that the method was used for reconstruction of three dimensional geological objects. First, manually a reference (gold standard) was created by redrawing contours of the halite crystals on each HRXCT scanning slice. Then, for OBIA, the computer program eCognition was used. For the automated reconstruction a rule set was developed. Thereby, the strength of OBIA was to recognize all objects similar to halite hopper crystals and in particular to eliminate cracks. In a second step, all the objects unsuitable for a structural deformation analysis were dismissed using a support vector machine (SVM) (clusters, polyhalite-coated crystals and spherical halites) The SVM simultaneously drastically reduced the number of halites. From 184 OBIA-objects 67 well shaped remained, which comes close to the number of pre-selected 52 objects. To assess the accuracy of the automated reconstruction, the result before and after SVM was compared to the reference, i.e. the gold standard. State-of the art per-scene statistics were extended to a per-object statistics. Görgey R (1912) Zur Kenntnis der Kalisalzlager von Wittelsheim im Ober-Elsaß. Tschermaks Mineral Petrogr Mitt 31:339-468 Gornitz VM, Schreiber BC (1981) Displacive halite hoppers from the dead sea: Some implications for ancient evaporite deposits. J of Sediment Petrol 51:787-794. doi: 10.1306/212F7DAB-2B24-11D7-8648000102C1865D Leitner C, Neubauer F, Marschallinger R, Genser J, Bernroider M (2013) Origin of deformed halite hopper crystals, pseudomorphic anhydrite cubes and polyhalite in Alpine evaporates (Austria, Germany). Int J Earth Sc 102, pp 813-829, doi: 10.1007/s00531-012-0836-6

75 FR 62560 - Exemption and Equivalent Arrangements Under the International Convention on Load Lines, 1966, as...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-12

... equivalent arrangements, as permitted by the ICLL and U.S. regulations, regarding hatch covers for hopper... Guard issued formal notification to the IMO of equivalent arrangements for hatch covers for certain... arrangements for hatch covers for certain manned, self-propelled open hopper dredges on November 12, 2009. We...

49 CFR 231.4 - Fixed-end low-side gondola and low-side hopper cars.

Code of Federal Regulations, 2013 CFR

2013-10-01

... cars. 231.4 Section 231.4 Transportation Other Regulations Relating to Transportation (Continued... Fixed-end low-side gondola and low-side hopper cars. (Cars with sides 36 inches or less above the floor are low-side cars.) (a) Hand brakes—(1) Number. Same as specified for “Box and other house cars” (see...

49 CFR 231.4 - Fixed-end low-side gondola and low-side hopper cars.

Code of Federal Regulations, 2014 CFR

2014-10-01

... cars. 231.4 Section 231.4 Transportation Other Regulations Relating to Transportation (Continued... Fixed-end low-side gondola and low-side hopper cars. (Cars with sides 36 inches or less above the floor are low-side cars.) (a) Hand brakes—(1) Number. Same as specified for “Box and other house cars” (see...

46 CFR 172.110 - Survival conditions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... flooding: (c) A hopper barge must not heel or trim beyond the angle at which— (1) The deck edge is first... section. (d) A hopper barge must not heel beyond the angle at which the deck edge is first submerged by... section, each tank barge must not heel beyond the angle at which— (1) The deck edge is first submerged; or...

46 CFR 172.110 - Survival conditions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... flooding: (c) A hopper barge must not heel or trim beyond the angle at which— (1) The deck edge is first... section. (d) A hopper barge must not heel beyond the angle at which the deck edge is first submerged by... section, each tank barge must not heel beyond the angle at which— (1) The deck edge is first submerged; or...

Preliminary evaluation of feeder and lint slide moisture addition on ginning, fiber quality, and textile processing of western cotton

USDA-ARS?s Scientific Manuscript database

The objective of this study was to evaluate the effects of moisture addition at the gin stand feeder conditioning hopper and/or the battery condenser slide on gin performance and Western cotton fiber quality and textile processing. The test treatments included no moisture addition, feeder hopper hum...

Unjamming a granular hopper by vibration

NASA Astrophysics Data System (ADS)

Janda, A.; Maza, D.; Garcimartín, A.; Kolb, E.; Lanuza, J.; Clément, E.

2009-07-01

We present an experimental study of the outflow of a hopper continuously vibrated by a piezoelectric device. Outpouring of grains can be achieved for apertures much below the usual jamming limit observed for non-vibrated hoppers. Granular flow persists down to the physical limit of one grain diameter, a limit reached for a finite vibration amplitude. For the smaller orifices, we observe an intermittent regime characterized by alternated periods of flow and blockage. Vibrations do not significantly modify the flow rates both in the continuous and the intermittent regime. The analysis of the statistical features of the flowing regime shows that the flow time significantly increases with the vibration amplitude. However, at low vibration amplitude and small orifice sizes, the jamming time distribution displays an anomalous statistics.

49 CFR 231.2 - Hopper cars and high-side gondolas with fixed ends.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 4 2014-10-01 2014-10-01 false Hopper cars and high-side gondolas with fixed ends... cars and high-side gondolas with fixed ends. (Cars with sides more than 36 inches above the floor are high-side cars.) (a) Hand brakes—(1) Number. Same as specified for “Box and other house cars” (see...

49 CFR 231.2 - Hopper cars and high-side gondolas with fixed ends.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Hopper cars and high-side gondolas with fixed ends... cars and high-side gondolas with fixed ends. (Cars with sides more than 36 inches above the floor are high-side cars.) (a) Hand brakes—(1) Number. Same as specified for “Box and other house cars” (see...

49 CFR 231.2 - Hopper cars and high-side gondolas with fixed ends.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 4 2013-10-01 2013-10-01 false Hopper cars and high-side gondolas with fixed ends... cars and high-side gondolas with fixed ends. (Cars with sides more than 36 inches above the floor are high-side cars.) (a) Hand brakes—(1) Number. Same as specified for “Box and other house cars” (see...

A Mission Concept: Re-Entry Hopper-Aero-Space-Craft System on-Mars (REARM-Mars)

NASA Technical Reports Server (NTRS)

Davoodi, Faranak

2013-01-01

Future missions to Mars that would need a sophisticated lander, hopper, or rover could benefit from the REARM Architecture. The mission concept REARM Architecture is designed to provide unprecedented capabilities for future Mars exploration missions, including human exploration and possible sample-return missions, as a reusable lander, ascend/descend vehicle, refuelable hopper, multiple-location sample-return collector, laboratory, and a cargo system for assets and humans. These could all be possible by adding just a single customized Re-Entry-Hopper-Aero-Space-Craft System, called REARM-spacecraft, and a docking station at the Martian orbit, called REARM-dock. REARM could dramatically decrease the time and the expense required to launch new exploratory missions on Mars by making them less dependent on Earth and by reusing the assets already designed, built, and sent to Mars. REARM would introduce a new class of Mars exploration missions, which could explore much larger expanses of Mars in a much faster fashion and with much more sophisticated lab instruments. The proposed REARM architecture consists of the following subsystems: REARM-dock, REARM-spacecraft, sky-crane, secure-attached-compartment, sample-return container, agile rover, scalable orbital lab, and on-the-road robotic handymen.

Food powders flowability characterization: theory, methods, and applications.

PubMed

Juliano, Pablo; Barbosa-Cánovas, Gustavo V

2010-01-01

Characterization of food powders flowability is required for predicting powder flow from hoppers in small-scale systems such as vending machines or at the industrial scale from storage silos or bins dispensing into powder mixing systems or packaging machines. This review covers conventional and new methods used to measure flowability in food powders. The method developed by Jenike (1964) for determining hopper outlet diameter and hopper angle has become a standard for the design of bins and is regarded as a standard method to characterize flowability. Moreover, there are a number of shear cells that can be used to determine failure properties defined by Jenike's theory. Other classic methods (compression, angle of repose) and nonconventional methods (Hall flowmeter, Johanson Indicizer, Hosokawa powder tester, tensile strength tester, powder rheometer), used mainly for the characterization of food powder cohesiveness, are described. The effect of some factors preventing flow, such as water content, temperature, time consolidation, particle composition and size distribution, is summarized for the characterization of specific food powders with conventional and other methods. Whereas time-consuming standard methods established for hopper design provide flow properties, there is yet little comparative evidence demonstrating that other rapid methods may provide similar flow prediction.

Investigation of the effect of wall friction on the flow rate in 2D and 3D Granular Flow

NASA Astrophysics Data System (ADS)

Carballo-Ramirez, Brenda; Pleau, Mollie; Easwar, Nalini; Birwa, Sumit; Shah, Neil; Tewari, Shubha

We have measured the mass flow rate of spherical steel spheres under gravity in vertical, straight-walled 2 and 3-dimensional hoppers, where the flow velocity is controlled by the opening size. Our measurements focus on the role of friction and its placement along the walls of the hopper. In the 2D case, an increase in the coefficient of static friction from μ = 0.2 to 0.6 is seen to decrease the flow rate significantly. We have changed the placement of frictional boundaries/regions from the front and back walls of the 2D hopper to the side walls and floor to investigate the relative importance of the different regions in determining the flow rate. Fits to the Beverloo equation show significant departure from the expected exponent of 1.5 in the case of 2D flow. In contrast, 3D flow rates do not show much dependence on wall friction and its placement. We compare the experimental data to numerical simulations of gravity driven hopper granular flow with varying frictional walls constructed using LAMMPS*. *http://lammps.sandia.gov Supported by NSF MRSEC DMR 0820506.

Continuous pressure letdown system

DOEpatents

Sprouse, Kenneth M.; Matthews, David R.; Langowski, Terry

2010-06-08

A continuous pressure letdown system connected to a hopper decreases a pressure of a 2-phase (gas and solid) dusty gas stream flowing through the system. The system includes a discharge line for receiving the dusty gas from the hopper, a valve, a cascade nozzle assembly positioned downstream of the discharge line, a purge ring, an inert gas supply connected to the purge ring, an inert gas throttle, and a filter. The valve connects the hopper to the discharge line and controls introduction of the dusty gas stream into the discharge line. The purge ring is connected between the discharge line and the cascade nozzle assembly. The inert gas throttle controls a flow rate of an inert gas into the cascade nozzle assembly. The filter is connected downstream of the cascade nozzle assembly.

30. HULETT NO. 2 IN MOTION; OPERATOR HAS JUST DUMPED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

30. HULETT NO. 2 IN MOTION; OPERATOR HAS JUST DUMPED A GRAB BUCKET OF ORE INTO THE RECEIVING HOPPER AND IS READY TO RETURN FOR ANOTHER LOAD. A ROUND TRIP FROM THE BOAT TO THE HOPPER AND BACK CAN BE MADE IN 50 SECONDS. - Pennsylvania Railway Ore Dock, Lake Erie at Whiskey Island, approximately 1.5 miles west of Public Square, Cleveland, Cuyahoga County, OH

The Mars Hopper: a radioisotope powered, impulse driven, long-range, long-lived mobile platform for exploration of Mars

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steven D. Howe; Robert C. O'Brien; William Taitano

Planetary exploration mission requirements are becoming more demanding. Due to the increasing cost, the missions that provide mobile platforms that can acquire data at multiple locations are becoming more attractive. Wheeled vehicles such as the MER rovers have proven extremely capable but have very limited range and cannot traverse rugged terrain. Flying vehicles such as balloons and airplanes have been proposed but are problematic due to the very thin atmospheric pressure and the strong, dusty winds present on Mars. The Center for Space Nuclear Research has designed an instrumented platform that can acquire detailed data at hundreds of locations duringmore » its lifetime - a Mars Hopper. The Mars Hopper concept utilizes energy from radioisotopic decay in a manner different from any existing radioisotopic power sources—as a thermal capacitor. By accumulating the heat from radioisotopic decay for long periods, the power of the source can be dramatically increased for short periods. The platform will be able to "hop" from one location to the next every 5-7 days with a separation of 5-10 km per hop. Preliminary designs show a platform that weighs around 52 kgs unfueled which is the condition at deployment. Consequently, several platforms may be deployed on a single launch from Earth. With sufficient lifetime, the entire surface of Mars can be mapped in detail by a couple dozen platforms. In addition, Hoppers can collect samples from all over the planet, including gorges, mountains and crevasses, and deliver them to a central location for eventual pick-up by a Mars Sample Return mission. The status of the Mars Hopper development project at the CSNR is discussed.« less

Scientific exploration of low-gravity planetary bodies using the Highland Terrain Hopper

NASA Astrophysics Data System (ADS)

Mège, D.; Grygorczuk, J.; Gurgurewicz, J.; Wiśniewski, Ł.; Rickman, H.; Banaszkiewicz, M.; Kuciński, T.; Skocki, K.

2013-09-01

Field geoscientists need to collect three-dimensional data in order characterise the lithologic succession and structure of terrains, recontruct their evolution, and eventually reveal the history of a portion of the planet. This is achieved by walking up and down mountains and valleys, interpreting geological and geophysical traverses, and reading measures made at station located at key sites on mountain peaks or rocky promontories. These activities have been denied to conventional planetary exploration rovers because engineering constraints for landing are strong, especially in terms of allowed terrain roughness and slopes. The Highland Terrain Hopper, a new, light and robust locomotion system, addresses the challenge of accessing most areas on low-gravity planetary body for performing scientific observations and measurements, alone or as part of a hopper commando. Examples of geological applications on Mars and the Moon are given.

1913 Richardson Scales in 1913 head house, looking east. The ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1913 Richardson Scales in 1913 head house, looking east. The balance beam on the right side of the photograph is for the west hopper scale. To the left and right are two discharge charges from the hopper scales. On the left is an auger that fills the bins. In the background is the grain cleaner. - Stewart Company Grain Elevator, 16 West Carson Street, Pittsburgh, Allegheny County, PA

Rotary bulk solids divider

DOEpatents

Maronde, Carl P.; Killmeyer, Jr., Richard P.

1992-01-01

An apparatus for the disbursement of a bulk solid sample comprising, a gravity hopper having a top open end and a bottom discharge end, a feeder positioned beneath the gravity hopper so as to receive a bulk solid sample flowing from the bottom discharge end, and a conveyor receiving the bulk solid sample from the feeder and rotating on an axis that allows the bulk solid sample to disperse the sample to a collection station.

ROTARY BULK SOLIDS DIVIDER

DOEpatents

Maronde, Carl P.; Killmeyer JR., Richard P.

1992-03-03

An apparatus for the disbursement of a bulk solid sample comprising, a gravity hopper having a top open end and a bottom discharge end, a feeder positioned beneath the gravity hopper so as to receive a bulk solid sample flowing from the bottom discharge end, and a conveyor receiving the bulk solid sample from the feeder and rotating on an axis that allows the bulk solid sample to disperse the sample to a collection station.

Development of the Variable Atmosphere Testing Facility for Blow-Down Analysis of the Mars Hopper Prototype

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nathan D. Jerred; Robert C. O'Brien; Steven D. Howe

Recent developments at the Center for Space Nuclear Research (CSNR) on a Martian exploration probe have lead to the assembly of a multi-functional variable atmosphere testing facility (VATF). The VATF has been assembled to perform transient blow-down analysis of a radioisotope thermal rocket (RTR) concept that has been proposed for the Mars Hopper; a long-lived, long-ranged mobile platform for the Martian surface. This study discusses the current state of the VATF as well as recent blow-down testing performed on a laboratory-scale prototype of the Mars Hopper. The VATF allows for the simulation of Mars ambient conditions within the pressure vesselmore » as well as to safely perform blow-down tests through the prototype using CO2 gas; the proposed propellant for the Mars Hopper. Empirical data gathered will lead to a better understanding of CO2 behavior and will provide validation of simulation models. Additionally, the potential of the VATF to test varying propulsion system designs has been recognized. In addition to being able to simulate varying atmospheres and blow-down gases for the RTR, it can be fitted to perform high temperature hydrogen testing of fuel elements for nuclear thermal propulsion.« less

Low NO.sub.x burner system

DOEpatents

Kitto, Jr., John B.; Kleisley, Roger J.; LaRue, Albert D.; Latham, Chris E.; Laursen, Thomas A.

1993-01-01

A low NO.sub.x burner system for a furnace having spaced apart front and rear walls, comprises a double row of cell burners on each of the front and rear walls. Each cell burner is either of the inverted type with a secondary air nozzle spaced vertically below a coal nozzle, or the non-inverted type where the coal nozzle is below the secondary air port. The inverted and non-inverted cells alternate or are provided in other specified patterns at least in the lower row of cells. A small percentage of the total air can be also provided through the hopper or hopper throat forming the bottom of the furnace, or through the boiler hopper side walls. A shallow angle impeller design also advances the purpose of the invention which is to reduce CO and H.sub.2 S admissions while maintaining low NO.sub.x generation.

Calculational note for the radiological and toxicological effects of a UO{sub 3} release from the T-hopper storage pad

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goldberg, H.J.

1998-06-18

UO{sub 3} powder is stored at the T-hopper storage area associated with the 2714-U building in the 200 west area. The T-hopper containers and 13 drums containing this material are used to store the powder on pads immediately north of the building. An interim safety basis document (WHC,1996) was issued in 1996 for the UO{sub 3} powder storage area. In this document the isotope {sup 99}Tc was not included in the source term used to calculate the radiological consequences of a postulated release of the powder. A calculations note (HNF, 1998) was issued to remedy that deficiency. The present documentmore » is a revision to that document to reflect updated data concerning the solubility of UO{sub 3} in simulated lung fluid and to utilize more realistic powder release fractions.« less

Some exact velocity profiles for granular flow in converging hoppers

NASA Astrophysics Data System (ADS)

Cox, Grant M.; Hill, James M.

2005-01-01

Gravity flow of granular materials through hoppers occurs in many industrial processes. For an ideal cohesionless granular material, which satisfies the Coulomb-Mohr yield condition, the number of known analytical solutions is limited. However, for the special case of the angle of internal friction δ equal to ninety degrees, there exist exact parametric solutions for the governing coupled ordinary differential equations for both two-dimensional wedges and three-dimensional cones, both of which involve two arbitrary constants of integration. These solutions are the only known analytical solutions of this generality. Here, we utilize the double-shearing theory of granular materials to determine the velocity field corresponding to these exact parametric solutions for the two problems of gravity flow through converging wedge and conical hoppers. An independent numerical solution for other angles of internal friction is shown to coincide with the analytical solution.

Phloem-specific expression of the lectin gene from Allium sativum confers resistance to the sap-sucker Nilaparvata lugens.

PubMed

Chandrasekhar, Kottakota; Vijayalakshmi, Muvva; Vani, Kalasamudramu; Kaul, Tanushri; Reddy, Malireddy K

2014-05-01

Rice production is severely hampered by insect pests. Garlic lectin gene (ASAL) holds great promise in conferring protection against chewing (lepidopteran) and sap-sucking (homopteran) insect pests. We have developed transgenic rice lines resistant to sap-sucking brown hopper (Nilaparvata lugens) by ectopic expression of ASAL in their phloem tissues. Molecular analyses of T0 lines confirmed stable integration of transgene. T1 lines (NP 1-2, 4-3, 11-6 & 17-7) showed active transcription and translation of ASAL transgene. ELISA revealed ASAL expression was as high as 0.95% of total soluble protein. Insect bioassays on T2 homozygous lines (NP 18 & 32) revealed significant reduction (~74-83%) in survival rate, development and fecundity of brown hoppers in comparison to wild type. Transgenics exhibited enhanced resistance (1-2 score) against brown hoppers, minimal plant damage and no growth penalty or phenotypic abnormalities.

National Waterways Study. Waterway Science and Technology.

DTIC Science & Technology

1981-08-01

Revetments 278 VII-A Split Hull Type Trailing Suction Hopper Dredge 304 VII-B Drag Heads 306 VII-C Overflow Systems 307 VII-D Trailing Suction Hopper... head reversals are possible. Poor approach conditions currently exist at some locks which could have been mitigated if modern, improved design...of ti,.c that a navigable pass section can be used. Navigation dams must be designed to pass high flows and floods with minor swell head and without in

Granular material flow in two-dimensional hoppers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brennen, C.; Pearce, J.C.

To aid in improving the transport of granular media for industrial purposes, the California Institute of Technology presents a comparison of experimental data with analytical results for the flow of dry granular media (such as coal) through a two-dimensional or wedge-shaped hopper. The analytical solution, which is based on the constitutive postulates (suggested by A.W. Jenike and R.T. Shield) of intergrain Coulomb friction and isotropy, produces results that are in good agreement with the experimental measurements.

Effects of wall friction on flow in a quasi-2D hopper

NASA Astrophysics Data System (ADS)

Shah, Neil; Birwa, Sumit; Carballo-Ramirez, Brenda; Pleau, Mollie; Easwar, Nalini; Tewari, Shubha

Our experiments on the gravity-driven flow of spherical particles in a vertical hopper examine how the flow rate varies with opening size and wall friction. We report here on a model simulation using LAMMPS of the experimental geometry, a quasi-2D hopper. Keeping inter-particle friction fixed, the coefficient of friction at the walls is varied from 0.0 to 0.9 for a range of opening sizes. Our simulations find a steady rate of flow at each wall friction and outlet size. The Janssen effect attributes the constant rate of flow of a granular column to the column height independence of the pressure at the base, since the weight of the grains is borne in part by friction at the walls. However, we observe a constant flow regime even in the absence of wall friction, suggesting that wall friction may not be a necessary condition for pressure saturation. The observed velocities of particles near the opening are used to extrapolate their starting positions had they been in free fall. In contrast to scaling predictions, our data suggest that the height of this free-fall arch does not vary with opening size for higher frictional coefficients. We analyze the velocity traces of particles to see the range over which contact interactions remain collisional as they approach the hopper outlet.

Regulating low-NOx and high-burnout deep-air-staging combustion under real-furnace conditions in a 600 MWe down-fired supercritical boiler by strengthening the staged-air effect.

PubMed

Kuang, Min; Wang, Zhihua; Zhu, Yanqun; Ling, Zhongqian; Li, Zhengqi

2014-10-21

A 600 MW(e) down-fired pulverized-coal supercritical boiler, which was equipped with a deep-air-staging combustion system for reducing the particularly high NOx emissions, suffered from the well-accepted contradiction between low NOx emissions and high carbon in fly ash, in addition to excessively high gas temperatures in the hopper that jeopardized the boiler's safe operations. Previous results uncovered that under low-NOx conditions, strengthening the staged-air effect by decreasing the staged-air angle and simultaneously increasing the staged-air damper opening alleviated the aforementioned problems to some extent. To establish low-NOx and high-burnout circumstances and control the aforementioned hopper temperatures, a further staged-air retrofit with horizontally redirecting staged air through an enlarged staged-air slot area was performed to greatly strengthen the staged-air effect. Full-load industrial-size measurements were performed to confirm the availability of this retrofit. The present data were compared with those published results before the retrofit. High NOx emissions, low carbon in fly ah, and high hopper temperatures (i.e., levels of 1036 mg/m(3) at 6% O2, 3.72%, and about 1300 °C, respectively) appeared under the original conditions with the staged-air angle of 45° and without overfire air (OFA) application. Applying OFA and reducing the angle to 20° achieved an apparent NOx reduction and a moderate hopper temperature decrease while a sharp increase in carbon in fly ash (i.e., levels of 878 mg/m(3) at 6% O2, about 1200 °C, and 9.81%, respectively). Fortunately, the present staged-air retrofit was confirmed to be applicable in regulating low-NOx, high-burnout, and low hopper temperature circumstances (i.e., levels of 867 mg/m(3) at 6% O2, 5.40%, and about 1100 °C, respectively).

Effect of Two-Way Air-Sea Coupling in High and Low Wind Speed Regimes

DTIC Science & Technology

2010-09-01

testing determined, however, that using a separate dynamical framework for the ocean model produced better results, primarily because it allowed for a...author address: Sue Chen, Naval Research Lab- oratory, 7 Grace Hopper Ave., Stop 2, Monterey, CA 93943-5502. E-mail: sue.chen@nrlmry.navy.mil 1 COAMPS is...ORGANIZATION NAME(S) AND ADDRESS(ES) Naval Research Laboratory,7 Grace Hopper Ave., Stop 2,Monterey, CA ,93943-5502 8. PERFORMING ORGANIZATION REPORT NUMBER 9

Analysis of a Radioisotope Thermal Rocket Engine

NASA Technical Reports Server (NTRS)

Machado-Rodriguez, Jonathan P.; Landis, Geoffrey A.

2017-01-01

The Triton Hopper is a concept for a vehicle to explore the surface of Neptunes moon Triton, which uses a radioisotope heated rocket engine and in-situ propellant acquisition. The initial Triton Hopper conceptual design stores pressurized Nitrogen in a spherical tank to be used as the propellant. The aim of the research was to investigate the benefits of storing propellant at ambient temperature and heating it through a thermal block during engine operation, as opposed to storing gas at a high temperature.

Mesoionic pyrido[1,2-a]pyrimidinones: Discovery of triflumezopyrim as a potent hopper insecticide1.

PubMed

Zhang, Wenming; Holyoke, Caleb W; Pahutski, Thomas F; Lahm, George P; Barry, James D; Cordova, Daniel; Leighty, Robert M; Singh, Vineet; Vicent, Daniel R; Tong, My-Hanh T; Hughes, Kenneth A; McCann, Stephen F; Henry, Yewande T; Xu, Ming; Briddell, Twyla A

2017-01-01

A novel class of mesoionic pyrido[1,2-a]pyrimidinones has been discovered with exceptional insecticidal activity controlling a number of insect species. In this communication, we report the part of the optimization program which led to the discovery of triflumezopyrim as a highly potent insecticide controlling various hopper species. Our efforts in discovery, synthesis, structure-activity relationship elucidation, and biological activity evaluation are also presented. Copyright © 2016 Elsevier Ltd. All rights reserved.

The role of preliminary magazine training in acquisition of the autoshaped key peck1

PubMed Central

Davol, G. H.; Steinhauer, G. D.; Lee, A.

1977-01-01

A series of experiments tested the hypothesis that initial key pecks in the autoshaping procedure are generalized pecks at the illuminated grain hopper. Experiment I found that autoshaping readily occurred when the chamber was continuously illuminated by a house-light. In Experiment II, pigeons given magazine training and autoshaping with an unlighted grain hopper failed to autoshape in 200 trials. Acquisition of autoshaped key pecking was retarded in Experiment III when stimulus control by the magazine light was reduced. In the fourth study, pigeons were given magazine training with either a red or white magazine light and then given autoshaping with concurrently presented red and white keys. For all pigeons in this experiment, the first key peck occurred on the key of the same color as that pigeon's magazine light. The results of these experiments were interpreted as supporting an account of autoshaping that identifies initial key pecks as arising due to generalization of pecking at the lighted grain hopper to pecking at the lighted key. PMID:16812027

Short-term response of subadult white sturgeon to hopper dredge disposal operations

USGS Publications Warehouse

Parsley, Michael J.; Popoff, Nicholas D.; Romine, Jason G.

2011-01-01

The effect of dredged-material disposal operations on the behavior of seven white sturgeon Acipenser transmontanus (50–101 cm fork length) was examined by analysis of the movements and depth use of these fish before, during, and after a series of hopper dredge disposal operations in the lower Columbia River. Analyses of fish locations showed that 12 flow-lane disposal operations within a 24-h period had minimal effect on subadult white sturgeon behavior; six of the seven fish showed slight attraction to the disposal area during disposals, and one fish increased its distance from the disposal area. The core area for all fish combined shifted toward the disposal area during disposals. In the 24 h after completion of the disposal operations the fish core areas shifted back toward those areas occupied before the disposals. The rates of movement, depths used, and diel movement patterns of the white sturgeon showed little change over all periods, suggesting that natural behaviors were not altered during and immediately after hopper dredge disposal operations.

Study of composition change and agglomeration of flue gas cleaning residue from a fluidized bed waste incinerator.

PubMed

Lievens, P; Verbinnen, B; Bollaert, P; Alderweireldt, N; Mertens, G; Elsen, J; Vandecasteele, C

2011-10-01

Blocking of the collection hoppers of the baghouse filters in a fluidized bed incinerator for co-incineration of high calorific industrial solid waste and sludge was observed. The composition of the flue gas cleaning residue (FGCR), both from a blocked hopper and from a normal hopper, was investigated by (differential) thermogravimetric analysis, quantitative X-ray powder diffraction and wet chemical analysis. The lower elemental carbon concentration and the higher calcium carbonate concentration of the agglomerated sample was the result of oxidation of carbon and subsequent reaction of CO2 with CaO. The evolved heat causes a temperature increase, with the decomposition of CaOHCl as a consequence. The formation of calcite and calcium chloride and the evolution of heat caused agglomeration of the FGCR. Activated lignite coke was replaced by another adsorption agent with less carbon, so the auto-ignition temperature increased; since then no further block formation has occurred.

Gravity flow rate of solids through orifices and pipes

NASA Technical Reports Server (NTRS)

Gardner, J. F.; Smith, J. E.; Hobday, J. M.

1977-01-01

Lock-hopper systems are the most common means for feeding solids to and from coal conversion reactor vessels. The rate at which crushed solids flow by gravity through the vertical pipes and valves in lock-hopper systems affects the size of pipes and valves needed to meet the solids-handling requirements of the coal conversion process. Methods used to predict flow rates are described and compared with experimental data. Preliminary indications are that solids-handling systems for coal conversion processes are over-designed by a factor of 2 or 3.

Leg exoskeleton reduces the metabolic cost of human hopping.

PubMed

Grabowski, Alena M; Herr, Hugh M

2009-09-01

During bouncing gaits such as hopping and running, leg muscles generate force to enable elastic energy storage and return primarily from tendons and, thus, demand metabolic energy. In an effort to reduce metabolic demand, we designed two elastic leg exoskeletons that act in parallel with the wearer's legs; one exoskeleton consisted of a multiple leaf (MLE) and the other of a single leaf (SLE) set of fiberglass springs. We hypothesized that hoppers, hopping on both legs, would adjust their leg stiffness while wearing an exoskeleton so that the combination of the hopper and exoskeleton would behave as a linear spring-mass system with the same total stiffness as during normal hopping. We also hypothesized that decreased leg force generation while wearing an exoskeleton would reduce the metabolic power required for hopping. Nine subjects hopped in place at 2.0, 2.2, 2.4, and 2.6 Hz with and without an exoskeleton while we measured ground reaction forces, exoskeletal compression, and metabolic rates. While wearing an exoskeleton, hoppers adjusted their leg stiffness to maintain linear spring-mass mechanics and a total stiffness similar to normal hopping. Without accounting for the added weight of each exoskeleton, wearing the MLE reduced net metabolic power by an average of 6% and wearing the SLE reduced net metabolic power by an average of 24% compared with hopping normally at frequencies between 2.0 and 2.6 Hz. Thus, when hoppers used external parallel springs, they likely decreased the mechanical work performed by the legs and substantially reduced metabolic demand compared with hopping without wearing an exoskeleton.

Distributor means for charging particulate material into receptacles

DOEpatents

Greaves, Melvin J.

1977-06-14

Disclosed are receptacles, such as shaft furnaces illustrated by a blast furnace and an upright oil shale retort, embodying rotatable charge distributor means for distributing particulate charge material in the furnace, which charge distributor means can provide a high uniformity of distribution of various sizes of particles and also can provide and maintain a stock line of desired contour and heighth in the receptacle. The distributor means includes a hopper having rigidly fixed to it a plurality of downwardly extending chutes with lower discharge portions that discharge in concentric circular zones at the stock line. The distributor means includes a segmented portion at the juncture of the hopper and the chutes that divides the charge material discharged into the hopper in proportion to the area of the circular zone at the stock line that is fed by the chute. The distributor means embodies means for providing mass flow of the particulate charge material through the chutes to the stock line and for avoiding segregation between larger and smaller particles of charge material deposited at the stock line.

Credit BG. This view looks northwest (290°) in the mixer ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit BG. This view looks northwest (290°) in the mixer room at the 30-gallon Baker-Perkins model 121/2 PVM mixer and its associated equipment. The hopper in the left background feeds ingredients to the mixing pot when the hopper is mounted on the mixer frame; the hoist overhead is used to mount the hopper. The mixing pot is in its lowered position beneath the mixer blades. The pot is normally raised and secured to the upper half of the mixer, and a vacuum is applied during mixing operations to prevent the entrainment of air bubbles in the mix. A second mixing pot appears in the right background, and a pot vacuum lid appears in the extreme right foreground. The equipment on the palette in the left foreground is not related to the mixer. Note the explosion-proof fluorescent lighting fixtures suspended from the ceiling. The floor has an electrically conductive coating to dissipate static electrical charges - Jet Propulsion Laboratory Edwards Facility, Mixer & Casting Building, Edwards Air Force Base, Boron, Kern County, CA

The Hopper System: How the Largest XE6 in the World Went From Requirements to Reality.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Antypas, Katie; Butler, Tina; Carter, Jonathan

This paper will discuss the entire process of acquiring and deploying Hopper from the first vendor market surveys to providing 3.8 million hours of production cycles per day for NERSC users. Installing the latest system at NERSC has been both a logistical and technical adventure. Balancing compute requirements with power, cooling, and space limitations drove the initial choice and configuration of the XE6, and a number of first-of- a-kind features implemented in collaboration with Cray have resulted in a high performance, usable, and reliable system.

13. BUILDING NO. 621, INTERIOR, TOP OF BLASTING TUB UNDERNEATH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. BUILDING NO. 621, INTERIOR, TOP OF BLASTING TUB UNDERNEATH SAWDUST HOPPER. BLASTING TUB HAS DOUBLE WALLS OF 3/4' THICK STEEL ARMOR PLATE. CHARGE TO BE TESTED IS BURIED IN SAWDUST WITH FLAME RESISTANT CHEMICALS. ELEVATOR BEHIND TUB CARRIES SAWDUST BACK TO TOP OF SAWDUST HOPPER AFTER TEST IS COMPLETED AND SAWDUST IN BLASTING TUB HAS BEEN SIFTED FOR SHELL FRAGMENTS. LOUVERS IN WALLS ARE HINGED FREELY SO THEY OPEN TO RELIEVE BLAST PRESSURE DURING A TEST. - Picatinny Arsenal, 600 Area, Test Areas District, State Route 15 near I-80, Dover, Morris County, NJ

Fluidized bed heat exchanger with water cooled air distributor and dust hopper

DOEpatents

Jukkola, Walfred W.; Leon, Albert M.; Van Dyk, Jr., Garritt C.; McCoy, Daniel E.; Fisher, Barry L.; Saiers, Timothy L.; Karstetter, Marlin E.

1981-11-24

A fluidized bed heat exchanger is provided in which air is passed through a bed of particulate material containing fuel. A steam-water natural circulation system is provided for heat exchange and the housing of the heat exchanger has a water-wall type construction. Vertical in-bed heat exchange tubes are provided and the air distributor is water-cooled. A water-cooled dust hopper is provided in the housing to collect particulates from the combustion gases and separate the combustion zone from a volume within said housing in which convection heat exchange tubes are provided to extract heat from the exiting combustion gases.

Methods and sorbents for utilizing a hot-side electrostatic precipitator for removal of mercury from combustion gases

DOEpatents

Nelson, Sidney [Hudson, OH

2011-02-15

Methods are provided for reducing emission of mercury from a gas stream by treating the gas with carbonaceous mercury sorbent particles to reduce the mercury content of the gas; collecting the carbonaceous mercury sorbent particles on collection plates of a hot-side ESP; periodically rapping the collection plates to release a substantial portion of the collected carbonaceous mercury sorbent particles into hoppers; and periodically emptying the hoppers, wherein such rapping and emptying are done at rates such that less than 70% of mercury adsorbed onto the mercury sorbent desorbs from the collected mercury sorbent into the gas stream.

Credit PSR. The interior of the grinder room appears as ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit PSR. The interior of the grinder room appears as seen looking southeast (148°), showing the remaining grinder equipment in the building. Note the blow-out wall in the background, and the water sprinkler head positioned over the hopper. The hopper top is connected to the dust receiver in the adjacent room. The blow-out wall is constructed to relieve pressure easily should an explosion occur, thus minimizing damage to the rest of the building structure. The floor has a conductive coating which dissipates static electrical charges that might otherwise cause fires - Jet Propulsion Laboratory Edwards Facility, Oxidizer Grinder Building, Edwards Air Force Base, Boron, Kern County, CA

Stagnation, circulation, and erosion of granular materials through belt conveyor sluice gate

NASA Astrophysics Data System (ADS)

Pohlman, Nicholas; Moralda, Michael; Dunne, Ryan

2013-11-01

Control of flow rates in conversion reactors for discrete materials like biomass can be achieved in belt conveyors through a combination of belt speed, hopper size, and aperture opening. As material is extracted from the bottom of the storage hopper, other material cannot achieve plug flow and therefore is restricted from exiting through a sluice-gate type opening. The excess material moves vertically from the opening causing a pile up and recirculation back along the free surface of the hopper. Experimental results obtained through high speed imaging show the position of the stagnation point as well as the rate of circulation is dependent on the mass flow rate achieved and instantaneous fill level. The movement of material into the plug flow along the belt allows verification of deposition models on erodible beds rather than rigid surfaces with artificial roughness of glued particles. Similarly, the pile-up at the exit influences the efficiency of the transport affecting the narrow energy return on investment of biomass resources. The laboratory-scale behavior can therefore be translated into industrial performance metrics for increased operational efficiency. This work is supported by the NSF REU Site Operation E-Tank under award number 1156789.

Stationary bubble formation and cavity collapse in wedge-shaped hoppers

PubMed Central

Yagisawa, Yui; Then, Hui Zee; Okumura, Ko

2016-01-01

The hourglass is one of the apparatuses familiar to everyone, but reveals intriguing behaviors peculiar to granular materials, and many issues are remained to be explored. In this study, we examined the dynamics of falling sand in a special form of hourglass, i.e., a wedge-shaped hopper, when a suspended granular layer is stabilized to a certain degree. As a result, we found remarkably different dynamic regimes of bubbling and cavity. In the bubbling regime, bubbles of nearly equal size are created in the sand at a regular time interval. In the cavity regime, a cavity grows as sand beads fall before a sudden collapse of the cavity. Bubbling found here is quite visible to a level never discussed in the physics literature and the cavity regime is a novel phase, which is neither continuous, intermittent nor completely blocked phase. We elucidate the physical conditions necessary for the bubbling and cavity regimes and develop simple theories for the regimes to successfully explain the observed phenomena by considering the stability of a suspended granular layer and clogging of granular flow at the outlet of the hopper. The bubbling and cavity regimes could be useful for mixing a fluid with granular materials. PMID:27138747

Structure of jammed configurations and their relation to unjamming times

NASA Astrophysics Data System (ADS)

Birwa, Sumit Kumar; Merrigan, Carl; Chakraborty, Bulbul; Tewari, Shubha

The distribution of the times for the cessation of flow of grains falling under gravity in a vertical hopper is known to be exponential. Recent experiments have shown, however, that the time lapse between avalanches follows a power-law distribution when the hopper is unjammed using periodic vertical vibrations. The reasons for this distribution of the unjamming times, which indicates the time needed for an applied continuous perturbation to induce another avalanche, are not well understood. We report on a numerical simulation of granular hopper flow using LAMMPS in which we seek to understand the origin and scope of this behavior. We find that cessation of flow is related to the formation of a stable arch that spans the system. However, the actual structure of the jammed configuration varies and is closely related to the unjamming time. We find that the symmetry of the arches is an important parameter in determining the strength of the jammed configurations. Using different force thresholds, we have characterized the contact networks around the arches which provides stability to the packed structure and analyzed the strength of various jammed configurations. Supported by NSF Grant DMR1409093 and DGE1068620.

Energy efficient continuous flow ash lockhopper

NASA Technical Reports Server (NTRS)

Collins, Earl R., Jr. (Inventor); Suitor, Jerry W. (Inventor); Dubis, David (Inventor)

1989-01-01

The invention relates to an energy efficient continuous flow ash lockhopper, or other lockhopper for reactor product or byproduct. The invention includes an ash hopper at the outlet of a high temperature, high pressure reactor vessel containing heated high pressure gas, a fluidics control chamber having an input port connected to the ash hopper's output port and an output port connected to the input port of a pressure letdown means, and a control fluid supply for regulating the pressure in the control chamber to be equal to or greater than the internal gas pressure of the reactor vessel, whereby the reactor gas is contained while ash is permitted to continuously flow from the ash hopper's output port, impelled by gravity. The main novelty resides in the use of a control chamber to so control pressure under the lockhopper that gases will not exit from the reactor vessel, and to also regulate the ash flow rate. There is also novelty in the design of the ash lockhopper shown in two figures. The novelty there is the use of annular passages of progressively greater diameter, and rotating the center parts on a shaft, with the center part of each slightly offset from adjacent ones to better assure ash flow through the opening.

Discharge flow of a granular media from a silo: effect of the packing fraction and of the hopper angle

NASA Astrophysics Data System (ADS)

Benyamine, Mebirika; Aussillous, Pascale; Dalloz-Dubrujeaud, Blanche

2017-06-01

Silos are widely used in the industry. While empirical predictions of the flow rate, based on scaling laws, have existed for more than a century (Hagen 1852, translated in [1] - Beverloo et al. [2]), recent advances have be made on the understanding of the control parameters of the flow. In particular, using continuous modeling together with a mu(I) granular rheology seem to be successful in predicting the flow rate for large numbers of beads at the aperture (Staron et al.[3], [4]). Moreover Janda et al.[5] have shown that the packing fraction at the outlet plays an important role when the number of beads at the apeture decreases. Based on these considerations, we have studied experimentally the discharge flow of a granular media from a rectangular silo. We have varied two main parameters: the angle of the hopper, and the bulk packing fraction of the granular material by using bidisperse mixtures. We propose a simple physical model to describe the effect of these parameters, considering a continuous granular media with a dilatancy law at the outlet. This model predicts well the dependance of the flow rate on the hopper angle as well as the dependance of the flow rate on the fine mass fraction of a bidisperse mixture.

Wolbachia infection complexity among insects in the tropical rice-field community.

PubMed

Kittayapong, P; Jamnongluk, W; Thipaksorn, A; Milne, J R; Sindhusake, C

2003-04-01

Wolbachia are a group of intracellular bacteria that cause reproductive alterations in their arthropod hosts. Widely discordant host and Wolbachia phylogenies indicate that horizontal transmission of these bacteria among species sometimes occurs. A likely means of horizontal transfer is through the feeding relations of organisms within communities. Feeding interactions among insects within the rice-field insect community have been well documented in the past. Here, we present the results of a polymerase chain reaction-based survey and phylogenetic analysis of Wolbachia strains in the rice-field insect community of Thailand. Our field survey indicated that 49 of 209 (23.4%) rice-field insect species were infected with Wolbachia. Of the 49 infected species, 27 were members of two feeding complexes: (i) a group of 13 hoppers preyed on by 2 mirid species and parasitized by a fly species, and (ii) 2 lepidopteran pests parasitized by 9 wasp species. Wolbachia strains found in three hoppers, Recilia dorsalis, Nephotettix malayanus and Nisia nervosa, the two mirid predators, Cyrtorhinus lividipennis and Tytthus chinensis, and the fly parasitoid, Tomosvaryella subvirescens, were all in the same Wolbachia clade. In the second complex, the two lepidopteran pests, Cnaphalocrocis medinalis and Scirpophaga incertulas, were both infected with Wolbachia from the same clade, as was the parasitoid Tropobracon schoenobii. However, none of the other infected parasitoid species in this feeding complex was infected by Wolbachia from this clade. Mean (+/- SD) genetic distance of Wolbachia wsp sequences among interacting species pairs of the hopper feeding complex (0.118 +/- 0.091 nucleotide sequence differences), but not for the other two complexes, was significantly smaller than that between noninteracting species pairs (0.162 +/- 0.079 nucleotide sequence differences). Our results suggest that some feeding complexes, such as the hopper complex described here, could be an important means by which Wolbachia spreads among species within arthropod communities.

Triton Hopper: Exploring Neptune's Captured Kuiper Belt Object

NASA Technical Reports Server (NTRS)

Oleson, Steve; Landis, Geoffrey

2018-01-01

Neptune's moon Triton is a fascinating object, a dynamic moon with an atmosphere, and geysers. Triton is unique in the outer solar system in that it is most likely a captured Kuiper belt object (KBO), a leftover building block of the solar system. When Voyager flew by it was the coldest body yet found in our solar system (33 degrees Kelvin) and had volcanic activity, geysers, and a thin atmosphere. It is covered in ices made from nitrogen, water, and carbon-dioxide, and shows surface deposits of tholins, organic compounds that may be precursor chemicals to the origin of life. Exploring Triton will be a challenge well beyond anything done in previous missions; but the unique environment of Triton also allows some new possibilities for mobility. We developed a conceptual design of a Triton Hopping probe that both analyzes the surface and collects it for use to propel its hops. The Hopper would land near the South Pole in 2040 where geysers have been detected. Depending the details of propulsion chosen the Hopper should be able to jump over 300 kilometers in 60 hops or less, exploring the surface and thin atmosphere on its way. This craft will autonomously carry out detailed scientific investigations on the surface, below the surface (drilling) and in the upper atmosphere to provide unprecedented knowledge of a KBO-turned moon and expanding NASA's existing capabilities in deep space planetary exploration to include Hoppers using different ices for propellant. Triton is roughly 2700 kilometers in diameter with a surface of mostly frozen nitrogen, mostly water ice crust and core of metal and rock. Its gravity is half that of Earth's Moon and its atmosphere is 170,000th of Earth's or 0.3 of Mars.The mission concept studied investigated the full surface and atmospheric phenomenon: chemical composition of surface and near subsurface materials, the thin atmosphere, volcanic and geyser activity. Measurements of all these aspects of Triton's unique environment can only be made through focused in-situ exploration with a well-instrumented craft. And this craft will be provided revolutionary mobility, nearly global, using in-situ ices as propellants. While other concepts have looked at gathering gases at Mars to propel a hopper, long periods of time are needed to gather the thin CO2 atmosphere. Several gases, mainly nitrogen are on the surface in a readily dense ice form and just need to be picked up, vaporized and used for propellant.

GROUT HOPPER MODELING STUDY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, S.

2011-08-30

The Saltstone facility has a grout hopper tank to provide agitator stirring of the Saltstone feed materials. The tank has about 300 gallon capacity to provide a larger working volume for the grout slurry to be held in case of a process upset, and it is equipped with a mechanical agitator, which is intended to keep the grout in motion and agitated so that it won't start to set up. The dry feeds and the salt solution are already mixed in the mixer prior to being transferred to the hopper tank. The hopper modeling study through this work will focusmore » on fluid stirring and agitation, instead of traditional mixing in the literature, in order to keep the tank contents in motion during their residence time so that they will not be upset or solidified prior to transferring the grout to the Saltstone disposal facility. The primary objective of the work is to evaluate the flow performance for mechanical agitators to prevent vortex pull-through for an adequate stirring of the feed materials and to estimate an agitator speed which provides acceptable flow performance with a 45{sup o} pitched four-blade agitator. In addition, the power consumption required for the agitator operation was estimated. The modeling calculations were performed by taking two steps of the Computational Fluid Dynamics (CFD) modeling approach. As a first step, a simple single-stage agitator model with 45{sup o} pitched propeller blades was developed for the initial scoping analysis of the flow pattern behaviors for a range of different operating conditions. Based on the initial phase-1 results, the phase-2 model with a two-stage agitator was developed for the final performance evaluations. A series of sensitivity calculations for different designs of agitators and operating conditions have been performed to investigate the impact of key parameters on the grout hydraulic performance in a 300-gallon hopper tank. For the analysis, viscous shear was modeled by using the Bingham plastic approximation. Steady state analyses with a two-equation turbulence model were performed with the FLUENT{trademark} codes. All analyses were based on three-dimensional results. Recommended operational guidance was developed by using the basic concept that local shear rate profiles and flow patterns can be used as a measure of hydraulic performance and spatial stirring. Flow patterns were estimated by a Lagrangian integration technique along the flow paths from the material feed inlet. The modeling results show that when the two-stage agitator consisting of a 45{sup o} pitched propeller and radial flat-plate blades is run at 140 rpm speed with 28 in diameter, the agitator provides an adequate stirring of the feed materials for a wide range of yield stresses (1 to 21 Pa) and the vortex system is shed into the remote region of the tank boundary by the blade passage in an efficient way. The results of this modeling study were used to develop the design guidelines for the agitator stirring and dispersion of the Saltstone feed materials in a hopper tank.« less

29 CFR 1926.750 - Scope.

Code of Federal Regulations, 2013 CFR

2013-07-01

... engaged in steel erection unless otherwise specified. This subpart does not cover electrical transmission...; car dumpers; stackers/reclaimers; cranes and craneways; bins; hoppers; ovens; furnaces; stacks...

29 CFR 1926.750 - Scope.

Code of Federal Regulations, 2012 CFR

2012-07-01

... engaged in steel erection unless otherwise specified. This subpart does not cover electrical transmission...; car dumpers; stackers/reclaimers; cranes and craneways; bins; hoppers; ovens; furnaces; stacks...

29 CFR 1926.750 - Scope.

Code of Federal Regulations, 2014 CFR

2014-07-01

... engaged in steel erection unless otherwise specified. This subpart does not cover electrical transmission...; car dumpers; stackers/reclaimers; cranes and craneways; bins; hoppers; ovens; furnaces; stacks...

29 CFR 1926.750 - Scope.

Code of Federal Regulations, 2011 CFR

2011-07-01

... engaged in steel erection unless otherwise specified. This subpart does not cover electrical transmission...; car dumpers; stackers/reclaimers; cranes and craneways; bins; hoppers; ovens; furnaces; stacks...

29 CFR 1926.750 - Scope.

Code of Federal Regulations, 2010 CFR

2010-07-01

... engaged in steel erection unless otherwise specified. This subpart does not cover electrical transmission...; car dumpers; stackers/reclaimers; cranes and craneways; bins; hoppers; ovens; furnaces; stacks...

Screw-fed pump system

DOEpatents

Sprouse, Kenneth M

2014-11-25

A pump system includes a pump that includes a first belt and a second belt that are spaced apart from each other to provide generally straight sides of a passage there between. There is an inlet at one end of the passage and an outlet at an opposite end of the passage, with a passage length that extends between the inlet and the outlet. The passage defines a gap distance in a width direction between the straight sides at the passage inlet. A hopper includes an interior space that terminates at a mouth at the passage inlet. At least one screw is located within the interior space of the hopper and includes a screw diameter in the width direction that is less than or equal to the gap distance.

Fly ash system technology improves opacity

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

2007-06-15

Unit 3 of the Dave Johnston Power Plant east of Glenrock, WY, USA had problems staying at or below the opacity limits set by the state. The unit makes use of a Lodge Cottrell precipitator. When the plant changed to burning Power River Basin coal, ash buildup became a significant issue as the fly ash control system was unable to properly evacuate hoppers on the unit. To overcome the problem, the PLC on the unit was replaced with a software optimization package called SmartAsh for the precipitator fly ash control system, at a cost of $500,000. After the upgrade, theremore » have been no plugged hoppers and the opacity has been reduced from around 20% to 3-5%. 2 figs.« less

The plant hopper Issus coleoptratus can detoxify phloem sap saponins including the degradation of the terpene core

PubMed Central

Himmelsbach, Markus; Weth, Agnes; Böhme, Christine; Schwarz, Martin; Bräunig, Peter; Baumgartner, Werner

2016-01-01

ABSTRACT Issus coleoptratus is a small plant hopper which mainly feeds on the phloem sap from ivy. Although all parts of ivy are poisonous as the plant contains saponins, especially hederasaponins, I. coleoptratus can cope with the poison. In contrast to other animals like the stick insect Carausius morosus which accumulates saponins in its body, I. coleoptratus can degrade and disintegrate not only the saponins but even the genines, i.e. the triterpene core of the substances. This is perhaps made possible by a specialised midgut and/or the salivary glands. When the glands and the gut are dissected and added to saponins in solution, the saponins, including the genines, are degraded ex vivo. PMID:26863940

Volumetric dispenser for small particles from plural sources

DOEpatents

Bradley, R.A.; Miller, W.H.; Sease, J.D.

1975-12-16

Apparatus is described for rapidly and accurately dispensing measured volumes of small particles from a supply hopper. The apparatus includes an adjustable, vertically oriented measuring tube and orifice member defining the volume to be dispensed, a ball plug valve for selectively closing the bottom end of the orifice member, and a compression valve for selectively closing the top end of the measuring tube. A supply hopper is disposed above and in gravity flow communication with the measuring tube. Properly sequenced opening and closing of the two valves provides accurate volumetric discharge through the ball plug valve. A dispensing system is described wherein several appropriately sized measuring tubes, orifice members, and associated valves are arranged to operate contemporaneously to facilitate blending of different particles.

The effects of physical and chemical preprocessing on the flowability of corn stover

DOE PAGES

Crawford, Nathan C.; Nagle, Nick; Sievers, David A.; ...

2015-12-20

Continuous and reliable feeding of biomass is essential for successful biofuel production. However, the challenges associated with biomass solids handling are commonly overlooked. In this study, we examine the effects of preprocessing (particle size reduction, moisture content, chemical additives, etc.) on the flow properties of corn stover. Compressibility, flow properties (interparticle friction, cohesion, unconfined yield stress, etc.), and wall friction were examined for five corn stover samples: ground, milled (dry and wet), acid impregnated, and deacetylated. The ground corn stover was found to be the least compressible and most flowable material. The water and acid impregnated stovers had similar compressibilities.more » Yet, the wet corn stover was less flowable than the acid impregnated sample, which displayed a flow index equivalent to the dry, milled corn stover. The deacetylated stover, on the other hand, was the most compressible and least flowable examined material. However, all of the tested stover samples had internal friction angles >30°, which could present additional feeding and handling challenges. All of the ''wetted'' materials (water, acid, and deacetylated) displayed reduced flowabilities (excluding the acid impregnated sample), and enhanced compressibilities and wall friction angles, indicating the potential for added handling issues; which was corroborated via theoretical hopper design calculations. All of the ''wetted'' corn stovers require larger theoretical hopper outlet diameters and steeper hopper walls than the examined ''dry'' stovers.« less

The effects of physical and chemical preprocessing on the flowability of corn stover

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crawford, Nathan C.; Nagle, Nick; Sievers, David A.

Continuous and reliable feeding of biomass is essential for successful biofuel production. However, the challenges associated with biomass solids handling are commonly overlooked. In this study, we examine the effects of preprocessing (particle size reduction, moisture content, chemical additives, etc.) on the flow properties of corn stover. Compressibility, flow properties (interparticle friction, cohesion, unconfined yield stress, etc.), and wall friction were examined for five corn stover samples: ground, milled (dry and wet), acid impregnated, and deacetylated. The ground corn stover was found to be the least compressible and most flowable material. The water and acid impregnated stovers had similar compressibilities.more » Yet, the wet corn stover was less flowable than the acid impregnated sample, which displayed a flow index equivalent to the dry, milled corn stover. The deacetylated stover, on the other hand, was the most compressible and least flowable examined material. However, all of the tested stover samples had internal friction angles >30°, which could present additional feeding and handling challenges. All of the ''wetted'' materials (water, acid, and deacetylated) displayed reduced flowabilities (excluding the acid impregnated sample), and enhanced compressibilities and wall friction angles, indicating the potential for added handling issues; which was corroborated via theoretical hopper design calculations. All of the ''wetted'' corn stovers require larger theoretical hopper outlet diameters and steeper hopper walls than the examined ''dry'' stovers.« less

Credit WCT. Original 2¾" x 2Y4" color negative is housed ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit WCT. Original 2-¾" x 2-Y4" color negative is housed in the JPL Photography Laboratory, Pasadena, California. View shows JPL staff member John Morrow loading the grinder hopper. The hopper has a 10 mesh screen to filter out particles too large for the mill. Oxidizer is passed steadily to the hammers by a stainless steel feed screw. Oxidizer may be passed through the mill several times depending on the fineness required by a given propellant formula; the maximum charge is 130 pounds (59.0 Kg). The drum below the mill has an electrically conductive plastic liner which receives the ground oxidizer (JPL negative no. JPL10279AC, 27 January 1989) - Jet Propulsion Laboratory Edwards Facility, Oxidizer Grinder Building, Edwards Air Force Base, Boron, Kern County, CA

Analysis of a Radioisotope Thermal Rocket Engine

NASA Technical Reports Server (NTRS)

Machado-Rodriguez, Jonathan P.; Landis, Geoffrey A.

2016-01-01

The Triton Hopper is a concept for a global hopper vehicle which uses a radioisotope rocket engine and In-situ propellant acquisition to explore the surface of Neptune's moon, Triton. The current Triton Hopper concept stores heated Nitrogen in a spherical tank to be used as the propellant. The aim of the research was to investigate the benefits of storing propellant at ambient temperature and heating it through the use of a thermal block during engine operation, as opposed to storing gas at a high temperature. Lithium, Lithium Fluoride and Beryllium were considered as possible materials for the thermal block. A heat energy analysis indicated that a lithium thermal mass would provide the highest heat energy for a temperature change from 900 Celsius to -100 Celsius. A heat transfer analysis was performed for Nitrogen at -100 Celsius flowing through 1000 passages inside a 1kg lithium thermal block at a temperature of 900 Celsius. The system was analyzed as turbulent flow through a tube with constant surface temperature. The analysis indicated that the propellant reached a maximum temperature of 877 Celsius before entering the nozzle. At this exit temperature, the average specific impulse [I(sub sp)] of the engine was determined to be 157s. Previous studies for the stored heated gas concept suggest that the engine would have an average I(sub sp) of approximately 52s. Thus, the use of a thermal block concept results in a 200 percent engine performance increase. In addition, a tank sizing study was performed to determine if the concept is feasible in terms of mass requirements. The mass for a spherical carbon fiber COPV storing 35kg of nitrogen at an initial temperature of -100 Celsius and a pressure of 1000psia, was determined to be 7.2kg. The specific impulse analysis indicated that the maximum engine performance is obtained for a mass ratio of 5kg of Nitrogen per every 1kg of lithium thermal mass. Thus for 35kg of Nitrogen the total thermal mass would be 7kg. This brings the total mass of the system to 49.2.kg which is less than the 56kg landing payload capacity of the Triton Hopper. Finally, an insulation analysis using 10mm of MLI insulation indicated that a total of 22 watts of heat are lost to the environment. With the heat loss known, the power required to heat the thermal mass to 900 Celsius in 24 days was determined to be 2.15 watts. The study's results allowed us to conclude that the thermal mass concept is the better option due to the performance increase provided, the low power requirement and its compliance with the landing mass requirement of the Triton Hopper.

Coal pump

DOEpatents

Bonin, John H.; Meyer, John W.; Daniel, Jr., Arnold D.

1983-01-01

A device for pressurizing pulverized coal and circulating a carrier gas is disclosed. This device has utility in a coal gasification process and eliminates the need for a separate collection hopper and eliminates the separate compressor.

Looking Northeast Along Hallway between Pellet Plant and Oxide Building, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Looking Northeast Along Hallway between Pellet Plant and Oxide Building, including Virgin Hopper Bins - Hematite Fuel Fabrication Facility, Pellet Plant, 3300 State Road P, Festus, Jefferson County, MO

Crystallization of Skeletal Diamonds from Graphite and Natural Coal in Presence of Hydrous Fluids at P=8 GPa and T=1400-1500° C

NASA Astrophysics Data System (ADS)

Dobrzhinetskaya, L. F.; Renfro, A. P.; Green, H. W.

2001-12-01

Most metamorphic microdiamonds from crustal UHP rocks of the Kokchetav massive, Kazakhstan are characterized by skeletal-hopper crystals, cuboid-like crystals with cavities "healed over" by graphite, rose-like crystals, and other imperfect morphologies. According to the classical theory of crystal growth at thermodynamic equilibrium, only shapes with a minimum surface energy are stable. Thus imperfect crystallographic forms of most metamorphic diamonds formally may be interpreted as metastable while the presence of other high pressure phases associated with diamond indicates that the rocks have been subjected to UHP metamorphism within the diamond stability field. The classical theory also says that a skeletal-hopper crystal is one that develops under conditions of rapid growth, a high degree of supersaturation and in the presence of impurities. In contrast to these observations, most experiments on diamond synthesis at high P (5-7.7 GPa) and T (1250 - 1900° C) from graphite (Wang et al., 1999; Hong et al., 1999; Yamaoka et al., 2000) and carbonate material (Pal'anov et al., 1999; Sokol et al.,2000) in presence of fluid phase produced perfect octahedral and cube-octahedral diamond crystals. Advanced analytical research on metamorphic diamonds and their inclusions has demonstrated that they were crystallized from a multicomponent COH-rich supercritical fluid phase, the composition of which suggests intermixture of crustal and mantle components (de Corte et al., 1999; Dobrzhinetskaya et al., 2001, Stockhert et al., 2001). We have recently synthesized imperfect diamond crystals (skeletal-hopper morphologies with effect of etching of the diamond surfaces) from graphite and natural coal + 2% Mg(OH)2 as a source for fluid phase. Conditions of experiments are: P=8-8.5 GPa, T=1400-1500° C, t=14 to 136 hours. Our experimental data are in a good agreement with similar experiments conducted by Kanda et al. (1984) who showed that with increasing water content of the system, the morphology of diamond crystals changes progressively from octahedra to crystals with elements of dodecahedra to hollow/hopper and skeletal morphologies. We hypothesize that imperfect morphologies of metamorphic diamonds are due to the presence of OH in the system.

It's an Interesting Article!

ERIC Educational Resources Information Center

Tracy, Karen

1993-01-01

It is argued that the combination of research methods used in Drummond and Hopper's article in this issue, "Back Channels Revisited," is appropriate. Factors that make for good social science research are discussed. (eight references) (LB)

Acknowledgment Tokens and Speakership Incipiency Revisited.

ERIC Educational Resources Information Center

Zimmerman, Don H.

1993-01-01

Drummond and Hopper's article in this issue, "Back Channels Revisited," is argued to have decontextualized Jefferson's acknowledgement token phenomenon. The need for careful coding protocols for research on conversational practices is discussed. (eight references) (LB)

Hopper on wheels: evolving the hopping robot concept

NASA Technical Reports Server (NTRS)

Schell, S.; Tretten, A.; Burdick, J.; Fuller, S. B.; Fiorini, P.

2001-01-01

This paper describes the evolution of our concept of hopping robot for planetary exploration, that combines coarse long range mobility achieved by hopping, with short range wheeled mobility for precision target acquisition.

Shape-Evolution Control of hybrid perovskite CH3NH3PbI3 crystals via solvothermal synthesis

NASA Astrophysics Data System (ADS)

Zhang, Baohua; Guo, Fuqiang; Yang, Lianhong; Jia, Xiuling; Liu, Bin; Xie, Zili; Chen, Dunjun; Lu, Hai; Zhang, Rong; Zheng, Youdou

2017-02-01

We systematically synthesized CH3NH3PbI3 crystals using solvothermal process, and the reaction conditions such as concentration of the precursor, temperature, time, and lead source have been comprehensively investigated to obtain shape-controlled CH3NH3PbI3 crystals. The results showed that the CH3NH3PbI3 crystals exhibit tetragonal phase and the crystals change from nanoparticles to hopper-faced cuboids. Photoluminescence spectra of the crystals obtained with different lead sources show a blue shift due to the presence of defects in the crystals, and the peak intensity is very sensitive to the lead sources. Moreover, impurities (undesirable byproducts and excess components like HI or CH3NH2) presented during crystal growth can result in hopper growth.

Flowability of JSC-1a

NASA Technical Reports Server (NTRS)

Rame, Enrique; Wilkinson, Allen; Elliot, Alan; Young, Carolyn

2009-01-01

We have done a complete flowability characterization of the lunar soil simulant, JSC-1a, following closely the ASTM-6773 standard for the Schulze ring shear test. The measurements, which involve pre-shearing the material before each yield point, show JSC-1a to be cohesionless, with an angle of internal friction near 40 deg. We also measured yield loci after consolidating the material in a vibration table which show it to have significant cohesion (approximately equal to 1 kPa) and an angle of internal friction of about 60 deg. Hopper designs based on each type of flowability test differ significantly. These differences highlight the need to discern the condition of the lunar soil in the specific process where flowability is an issue. We close with a list not necessarily comprehensive of engineering rules of thumb that apply to powder flow in hoppers.

Hopper apparatuses for processing a bulk solid, and related systems and methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Westover, Tyler Lott; Ryan, John Chadron Benjamin; Matthews, Austin Colter

A hopper apparatus comprises a movable wall comprising opposing walls movably connected to a support assembly and oriented at acute angles relative to a central vertical axis of the support assembly, and movement control devices configured and positioned to move the opposing walls along the support assembly to control dimensions of a discharge outlet at least partially defined by converging ends of the opposing walls; a liner assembly comprising liner structures at least partially overlying inner surfaces of the opposing walls and configured to remain at least partially stationary relative to the opposing walls during movement of the opposing walls;more » and pressure sensors between the inner surfaces of opposing walls and portions of the liner structures thereover. A bulk solids processing system and a method of processing a bulk solid are also described.« less

Effect of interstitial fluid on the fraction of flow microstates that precede clogging in granular hoppers

NASA Astrophysics Data System (ADS)

Koivisto, Juha; Durian, Douglas J.

2017-03-01

We report on the nature of flow events for the gravity-driven discharge of glass beads through a hole that is small enough that the hopper is susceptible to clogging. In particular, we measure the average and standard deviation of the distribution of discharged masses as a function of both hole and grain sizes. We do so in air, which is usual, but also with the system entirely submerged under water. This damps the grain dynamics and could be expected to dramatically affect the distribution of the flow events, which are described in prior work as avalanche-like. Though the flow is slower and the events last longer, we find that the average discharge mass is only slightly reduced for submerged grains. Furthermore, we find that the shape of the distribution remains exponential, implying that clogging is still a Poisson process even for immersed grains. Per Thomas and Durian [Phys. Rev. Lett. 114, 178001 (2015), 10.1103/PhysRevLett.114.178001], this allows for an interpretation of the average discharge mass in terms of the fraction of flow microstates that precede, i.e., that effectively cause, a stable clog to form. Since this fraction is barely altered by water, we conclude that the crucial microscopic variables are the grain positions; grain momenta play only a secondary role in destabilizing weak incipient arches. These insights should aid ongoing efforts to understand the susceptibility of granular hoppers to clogging.

Contrast and autoshaping in multiple schedules varying reinforcer rate and duration.

PubMed

Hamilton, B E; Silberberg, A

1978-07-01

Thirteen master pigeons were exposed to multiple schedules in which reinforcement frequency (Experiment I) or duration (Experiment II) was varied. In Phases 1 and 3 of Experiment I, the values of the first and second components' random-interval schedules were 33 and 99 seconds, respectively. In Phase 2, these values were 99 seconds for both components. In Experiment II, a random-interval 33-second schedule was associated with each component. During Phases 1 and 3, the first and second components had hopper durations of 7.5 and 2.5 seconds respectively. During Phase 2, both components' hopper durations were 2.5 seconds. In each experiment, positive contrast obtained for about half the master subjects. The rest showed a rate increase in both components (positive induction). Each master subject's key colors and reinforcers were synchronously presented on a response-independent basis to a yoked control. Richer component key-pecking occurred during each experiment's Phases 1 and 3 among half these subjects. However, none responded during the contrast condition (unchanged component of each experiment's Phase 2). From this it is inferred that autoshaping did not contribute to the contrast and induction findings among master birds. Little evidence of local contrast (highest rate at beginning of richer component) was found in any subject. These data show that (a) contrast can occur independently from autoshaping, (b) contrast assays during equal-valued components may produce induction, (c) local contrast in multiple schedules often does not occur, and (d) differential hopper durations can produce autoshaping and contrast.

AUTOMOTIVE REPAIR SHOP, DETAIL OF MILLS COAL BOILER WITH SCREWFEED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

AUTOMOTIVE REPAIR SHOP, DETAIL OF MILLS COAL BOILER WITH SCREW-FEED COAL HOPPER ON RIGHT SIDE. - Cedar City Automotive Repair Shop, Automotive Repair Shop, 820 North Main Street, Cedar City, Iron County, UT

View towards the northeast of coffee beans drying on the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View towards the northeast of coffee beans drying on the third floor with hopper and drum type dryer in background - Santaella Coffee Processing Site, Highway 139, Kilometer 10.6, Maraguez, Ponce Municipio, PR

49 CFR 215.5 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) Refrigerator car; (3) Ventilator car; (4) Stock car; (5) Gondola car; (6) Hopper car; (7) Flat car; (8) Special...: (1) The cars are operated— (i) Primarily on track that is inside an industrial or other non-railroad...

46 CFR 174.315 - Extent and character of damage.

Code of Federal Regulations, 2011 CFR

2011-10-01

... PERTAINING TO SPECIFIC VESSEL TYPES Hopper Dredges With Working Freeboard Assignments Calculations § 174.315 Extent and character of damage. (a) The calculations required by § 174.310 must show that the dredge can...

46 CFR 174.315 - Extent and character of damage.

Code of Federal Regulations, 2010 CFR

2010-10-01

... PERTAINING TO SPECIFIC VESSEL TYPES Hopper Dredges With Working Freeboard Assignments Calculations § 174.315 Extent and character of damage. (a) The calculations required by § 174.310 must show that the dredge can...

8. VIEW TO NORTH OF INTERIOR OF STAMPMILLING LEVEL; MORTAR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

8. VIEW TO NORTH OF INTERIOR OF STAMPMILLING LEVEL; MORTAR MOUNT FOR MILL IS IMMEDIATELY BELOW AND TO LEFT OF ORE-HOPPER (UPPER-CENTER). - Steamboat Stampmill, Brush Creek Canyon, Jacksonville, Jackson County, OR

AUTOMOTIVE REPAIR SHOP, DETAIL OF MILLS COAL BOILER WITH SCREWFEED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

AUTOMOTIVE REPAIR SHOP, DETAIL OF MILLS COAL BOILER WITH SCREW-FEED COAL HOPPER ON RIGHT SIDE, WITH SCALE. - Cedar City Automotive Repair Shop, Automotive Repair Shop, 820 North Main Street, Cedar City, Iron County, UT

32. Coffee bean sluiceway on ground floor showing chute bringing ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

32. Coffee bean sluiceway on ground floor showing chute bringing beans from first floor hopper. HAER PR, 6-MAGU, 1B-17 - Hacienda Buena Vista, PR Route 10 (Ponce to Arecibo), Magueyes, Ponce Municipio, PR

Performance of a Retrofitted Multicyclone for PM2.5 Emission Control

NASA Astrophysics Data System (ADS)

Dewika, M.; Rashid, M.; Ammar, M. R.

2018-03-01

This paper presents on the performance of a retrofitted multicyclone system, which aims to increase the collection efficiency of PM2.5 (i.e. particulate size fraction ≤ 2.5 μm) emission. The multicyclone was retrofitted by extracting 15% and 20% of the total volumetric air flow rate at the dust hopper of the unit using an additional Induced Draft Fan. The total collection efficiency with and without the extraction was measured at various air volumetric flow rates and particulate mass inlet concentration. The results showed that there was a reduction of 12% to 54% depending on the inlet concentration of PM2.5 emission in the stack with compared to without extraction increasing the collection efficiency of the retrofitted multicyclone. The finding suggests that a simple technique of applying gas extraction at the dust hopper of a multicyclone as reported in this study able to increase the overall performance in fine particulate collection.

Transporting particulate material

DOEpatents

Aldred, Derek Leslie [North Hollywood, CA; Rader, Jeffrey A [North Hollywood, CA; Saunders, Timothy W [North Hollywood, CA

2011-08-30

A material transporting system comprises a material transporting apparatus (100) including a material transporting apparatus hopper structure (200, 202), which comprises at least one rotary transporting apparatus; a stationary hub structure (900) constraining and assisting the at least one rotary transporting apparatus; an outlet duct configuration (700) configured to permit material to exit therefrom and comprising at least one diverging portion (702, 702'); an outlet abutment configuration (800) configured to direct material to the outlet duct configuration; an outlet valve assembly from the material transporting system venting the material transporting system; and a moving wall configuration in the material transporting apparatus capable of assisting the material transporting apparatus in transporting material in the material transporting system. Material can be moved from the material transporting apparatus hopper structure to the outlet duct configuration through the at least one rotary transporting apparatus, the outlet abutment configuration, and the outlet valve assembly.

Mars Surface Mobility Leading to Sustainable Exploration

NASA Technical Reports Server (NTRS)

Linne, Diane L.; Barsi, Stephen J.; Sjauw En Wa, Waldy K.; Landis, Geoffrey A.

2012-01-01

A Mars rocket-propelled hopper concept was evaluated for feasibility through analysis and experiments. The approach set forth in this paper is to combine the use of in-situ resources in a new Mars mobility concept that will greatly enhance the science return while providing the first opportunity towards reducing the risk of incorporating ISRU into the critical path for the highly coveted, but currently unaffordable, sample return mission. Experimental tests were performed on a high-pressure, self-throttling gaseous oxygen/methane propulsion system to simulate a two-burn-with-coast hop profile. Analysis of the trajectory, production plant requirements, and vehicle mass indicates that a small hopper vehicle could hop 2 km every 30 days with an initial mass of less than 60 kg. A larger vehicle can hop 15 km every 30 to 60 days with an initial mass of 300 to 430 kg.

Lock hopper values for coal gasification plant service

NASA Technical Reports Server (NTRS)

Schoeneweis, E. F.

1977-01-01

Although the operating principle of the lock hopper system is extremely simple, valve applications involving this service for coal gasification plants are likewise extremely difficult. The difficulties center on the requirement of handling highly erosive pulverized coal or char (either in dry or slurry form) combined with the requirement of providing tight sealing against high-pressure (possibly very hot) gas. Operating pressures and temperatures in these applications typically range up to 1600 psi (110bar) and 600F (316C), with certain process requirements going even higher. In addition, and of primary concern, is the need for reliable operation over long service periods with the provision for practical and economical maintenance. Currently available data indicate the requirement for something in the order of 20,000 to 30,000 open-close cycles per year and a desire to operate at least that long without valve failure.

Preparation, Characterization, and Insecticidal Activity of Avermectin-Grafted-Carboxymethyl Chitosan

PubMed Central

Li, Yan; Qin, Yukun; Liu, Song; Xing, Ronge; Yu, Huahua; Li, Kecheng; Li, Pengcheng

2016-01-01

Avermectin-grafted-N,O-carboxymethyl chitosan (NOCC) derivative was obtained by esterification reaction using dicyclohexylcarbodiimide (DCC) as dehydrating agent and 4-methylaminopyridine as catalyst. The structures of the conjugate were confirmed by FT-IR, 1H NMR, and XRD. Insecticidal activities against armyworms, carmine spider mites, black bean aphids, and brown plant hoppers were investigated at concentrations ranging from 0.16 to 1000 mg/L. At the concentration of 1000 mg/L and 500 mg/L, the lethal rate was 100%. Good insecticidal activity at 4 mg/L was still shown, especially against the black bean aphids and brown plant hoppers. Moreover, the photostability of the conjugate was evaluated and showed an apparent improvement. At 300 mins, the residual rate of the conjugate was 11.22%, much higher than 0.2% of the avermectin technical material. The conjugate we developed showed potential for further study and application in crop protection. PMID:27213156

Determination of an effective sampling regime to detect salmonella enteritidis in the environment of poultry units.

PubMed

Davies, R H; Wray, C

1996-05-01

A study of the dissemination of Salmonella enteritidis in the poultry breeder industry in the UK showed that the choice of sites for sampling the environment of occupied houses and empty houses which had been disinfected after depopulation had a significant influence on the outcome. Increased isolation rates could be achieved by sampling nest box floors and dust in open slave feed hoppers in occupied poultry houses. Nest box floors were the most sensitive sites for detection of residual environmental contamination in poultry houses where enrofloxacin treatment had been used. Floor sweepings, nest box floors, slave feed hoppers, hydrated wall fabric junctions and high beams and pipes were the most sensitive sample sites in cleansed and disinfected poultry houses. The use of universal disinfectant neutralisers gave good results in laboratory trials but appeared to reduce the isolation rate from field samples.

Stability of Granular Packings Jammed under Gravity: Avalanches and Unjamming

NASA Astrophysics Data System (ADS)

Merrigan, Carl; Birwa, Sumit; Tewari, Shubha; Chakraborty, Bulbul

Granular avalanches indicate the sudden destabilization of a jammed state due to a perturbation. We propose that the perturbation needed depends on the entire force network of the jammed configuration. Some networks are stable, while others are fragile, leading to the unpredictability of avalanches. To test this claim, we simulated an ensemble of jammed states in a hopper using LAMMPS. These simulations were motivated by experiments with vibrated hoppers where the unjamming times followed power-law distributions. We compare the force networks for these simulated states with respect to their overall stability. The states are classified by how long they remain stable when subject to continuous vibrations. We characterize the force networks through both their real space geometry and representations in the associated force-tile space, extending this tool to jammed states with body forces. Supported by NSF Grant DMR1409093 and DGE1068620.

An investigation into the impact of magnesium stearate on powder feeding during roller compaction.

PubMed

Dawes, Jason; Gamble, John F; Greenwood, Richard; Robbins, Phil; Tobyn, Mike

2012-01-01

A systematic evaluation on the effect of magnesium stearate on the transmission of a placebo formulation from the hopper to the rolls during screw fed roller compaction has been carried out. It is demonstrated that, for a system with two 'knurled' rollers, addition of 0.5% w/w magnesium stearate can lead to a significant increase in ribbon mass throughput, with a consequential increase in roll gap, compared to an unlubricated formulation (manufactured at equivalent process conditions). However, this effect is reduced if one of the rollers is smooth. Roller compaction of a lubricated formulation using two smooth rollers was found to be ineffective due to a reduction in friction at the powder/roll interface, i.e. powder was not drawn through the rollers leading to a blockage in the feeding system. An increase in ribbon mass throughput could also be achieved if the equipment surfaces were pre-lubricated. However this increase was found to be temporary suggesting that the residual magnesium stearate layer was removed from the equipment surfaces. Powder sticking to the equipment surfaces, which is common during pharmaceutical manufacturing, was prevented if magnesium stearate was present either in the blend, or at the roll surface. It is further demonstrated that the influence of the hopper stirrer, which is primarily used to prevent bridge formation in the hopper and help draw powder more evenly into the auger chamber, can lead to further mixing of the formulation, and could therefore affect a change in the lubricity of the carefully blended input material.

Diet Replenishment for Ad-libitum–fed Mice Housed in Social Groups is Compatible with Shelf Life

PubMed Central

Huerkamp, Michael J; Dowdy, Minida R

2008-01-01

Regulatory guidelines and best practices in the care of research animals allow diets milled for laboratory animals to be used within 180 d of formulation but otherwise permit latitude and professional judgment in how and when feed is offered. As such, practices at some research institutions allow for the replenishment (‘topping up’) of fresh chow over that existing in the cage food hopper, rather than complete replacement of the diet on a regular basis. To determine the depletion rate of a pelleted diet as fed from a conventional overhead food hopper, the consumption of full hoppers of food was measured for breeding pairs of mice in production and gender-specific groups of weanlings and juvenile mice kept in ventilated cages at 71.9 ± 0.2 °F (approximately 22.6 °C) and 40% ± 5% relative humidity. Breeding pairs of mice depleted 97% of a 250-g ration within 44 d of offering and consumed diet at a rate of 4.7 ± 0.5 g per mouse daily. Gender-grouped weanling and juvenile mice housed 5 to 6 per cage exhausted more than 99% of a 500-g ration of diet in 24 d and consumed chow at a rate of 3.4 ± 0.3 g per animal daily. These findings suggest that breeding pairs and groups of mice kept 5 to 6 per cage deplete feed at such a rate that diets can be fed by using replenishment provided diet is offered within 5 mo of the milling date. PMID:18459713

Contrast and autoshaping in multiple schedules varying reinforcer rate and duration

PubMed Central

Hamilton, Bruce E.; Silberberg, Alan

1978-01-01

Thirteen master pigeons were exposed to multiple schedules in which reinforcement frequency (Experiment I) or duration (Experiment II) was varied. In Phases 1 and 3 of Experiment I, the values of the first and second components' random-interval schedules were 33 and 99 seconds, respectively. In Phase 2, these values were 99 seconds for both components. In Experiment II, a random-interval 33-second schedule was associated with each component. During Phases 1 and 3, the first and second components had hopper durations of 7.5 and 2.5 seconds respectively. During Phase 2, both components' hopper durations were 2.5 seconds. In each experiment, positive contrast obtained for about half the master subjects. The rest showed a rate increase in both components (positive induction). Each master subject's key colors and reinforcers were synchronously presented on a response-independent basis to a yoked control. Richer component key-pecking occurred during each experiment's Phases 1 and 3 among half these subjects. However, none responded during the contrast condition (unchanged component of each experiment's Phase 2). From this it is inferred that autoshaping did not contribute to the contrast and induction findings among master birds. Little evidence of local contrast (highest rate at beginning of richer component) was found in any subject. These data show that (a) contrast can occur independently from autoshaping, (b) contrast assays during equal-valued components may produce induction, (c) local contrast in multiple schedules often does not occur, and (d) differential hopper durations can produce autoshaping and contrast. PMID:16812081

View towards Foundry and Pattern Storage Room, blocked by 3 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View towards Foundry and Pattern Storage Room, blocked by 3 bay hopper coal cars in foreground - East Broad Top Railroad & Coal Company, State Route 994, West of U.S. Route 522, Rockhill Furnace, Huntingdon County, PA

46 CFR 172.100 - Watertight integrity.

Code of Federal Regulations, 2010 CFR

2010-10-01

... calculations to have at least 2 inches (50 mm) of positive GM when the hopper space is flooded to the height of... calculations to be strong enough to hold the tanks in place when they are subjected to the buoyant forces...

46 CFR 172.100 - Watertight integrity.

Code of Federal Regulations, 2013 CFR

2013-10-01

... calculations to have at least 2 inches (50 mm) of positive GM when the hopper space is flooded to the height of... calculations to be strong enough to hold the tanks in place when they are subjected to the buoyant forces...

40 CFR 63.11453 - What are the initial compliance demonstration requirements for new and existing sources?

Code of Federal Regulations, 2011 CFR

2011-07-01

... functioning of the electronic controls for corona power and rapper operation, that the corona wires are... determine the condition and integrity of corona wires, collection plates, hopper, and air diffuser plates...

40 CFR 63.11453 - What are the initial compliance demonstration requirements for new and existing sources?

Code of Federal Regulations, 2014 CFR

2014-07-01

... functioning of the electronic controls for corona power and rapper operation, that the corona wires are... determine the condition and integrity of corona wires, collection plates, hopper, and air diffuser plates...

40 CFR 63.11453 - What are the initial compliance demonstration requirements for new and existing sources?

Code of Federal Regulations, 2012 CFR

2012-07-01

... functioning of the electronic controls for corona power and rapper operation, that the corona wires are... determine the condition and integrity of corona wires, collection plates, hopper, and air diffuser plates...

40 CFR 63.11453 - What are the initial compliance demonstration requirements for new and existing sources?

Code of Federal Regulations, 2010 CFR

2010-07-01

... functioning of the electronic controls for corona power and rapper operation, that the corona wires are... determine the condition and integrity of corona wires, collection plates, hopper, and air diffuser plates...

40 CFR 63.11453 - What are the initial compliance demonstration requirements for new and existing sources?

Code of Federal Regulations, 2013 CFR

2013-07-01

... functioning of the electronic controls for corona power and rapper operation, that the corona wires are... determine the condition and integrity of corona wires, collection plates, hopper, and air diffuser plates...

7 CFR 58.212 - Hopper or dump room.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) REGULATIONS AND STANDARDS UNDER THE AGRICULTURAL MARKETING ACT OF 1946 AND THE EGG PRODUCTS INSPECTION ACT (CONTINUED) GRADING AND INSPECTION...

1. Building 15 west elevation oblique showing coal conveyor, chute ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. Building 15 west elevation oblique showing coal conveyor, chute and hopper. Coal feeds boiler in Building 3. View looking SE. - John & James Dobson Carpet Mill (West Parcel), Building No. 15, 4041-4055 Ridge Avenue, Philadelphia, Philadelphia County, PA

1. GENERAL VIEW OF TIPPLE LOOKING NORTHWEST, SHOWING LARRY CARS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. GENERAL VIEW OF TIPPLE LOOKING NORTHWEST, SHOWING LARRY CARS BELOW HOPPER BIN. GRAY FITZSIMONS, HAER HISTORIAN, IS STANDING ON PLATFORM NEXT TO LARRY CARS - Lucernemines Coke Works, Larry Car Tipple, East of Lucerne, Lucerne Mines, Indiana County, PA

3. SIXTH FLOOR VIEW TO WEST, WITH FACE POWDER MAKING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. SIXTH FLOOR VIEW TO WEST, WITH FACE POWDER MAKING UNIT: CHARGE HOPPER (CENTER FOREGROUND), PERFUME MIXER (LEFT), AND DUST COLLECTOR (REAR CENTER) - Colgate & Company Jersey City Plant, G Block, 81-95 Greene Street, Jersey City, Hudson County, NJ

9. VIEW OF FLOOR 2 LOOKING EAST; SHOWS GREAT SPUR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. VIEW OF FLOOR 2 LOOKING EAST; SHOWS GREAT SPUR WHEEL AND TWO STONE NUTS, AND THE CHUTES, HOPPERS, HORSES AND SHOES OF THE GRAIN FEED SYSTEM - Hook Windmill, North Main Street at Pantigo Road, East Hampton, Suffolk County, NY

46 CFR 174.300 - Specific applicability.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Specific applicability. 174.300 Section 174.300 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SUBDIVISION AND STABILITY SPECIAL RULES PERTAINING TO SPECIFIC VESSEL TYPES Hopper Dredges With Working Freeboard Assignments § 174.300 Specific...

Homelessness in America.

ERIC Educational Resources Information Center

Baumohl, Jim, Ed.

This book about homelessness in the United States offers 16 chapters in three parts. Part 1, "History Definitions, and Causes," includes: (1) "Redefining the Cursed Word: A Historical Interpretation of American Homelessness" (Kim Hopper and Jim Baumohl); (2) "Homelessness: Definitions and Counts" (Martha R. Burt); (3)…

6. 5TH FLOOR, VIEW NORTH OF KETTLE SOAP STORAGE TANKS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. 5TH FLOOR, VIEW NORTH OF KETTLE SOAP STORAGE TANKS (RIGHT) AND WEIGH HOPPERS OVER SITES OF REMOVED AMALGAMATORS (LEFT) - Colgate & Company Jersey City Plant, Building No. B-14, 54-58 Grand Street, Jersey City, Hudson County, NJ

40. William E. Barrett, Photographer, August 1975. ROOF OF POWERHOUSE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

40. William E. Barrett, Photographer, August 1975. ROOF OF POWERHOUSE SHOWING HOPPERS FOR SAWDUST USED TO FIRE STEAM BOILERS. DUCTS AT LEFT LEAD FROM PLANNING MILL AND OTHER MANUFACTURING OPERATIONS. - Meadow River Lumber Company, Highway 60, Rainelle, Greenbrier County, WV

40 CFR 442.1 - General applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... under a wide variety of Standard Industrial Classification (SIC) codes. Several of the most common SIC... industrial, commercial, or Publicly Owned Treatment Works (POTW) operations, provided that the cleaning is... drums, intermediate bulk containers, or closed-top hoppers. (3) Wastewater from a facility that...

46 CFR 174.325 - Equalization.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 7 2011-10-01 2011-10-01 false Equalization. 174.325 Section 174.325 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SUBDIVISION AND STABILITY SPECIAL RULES PERTAINING TO SPECIFIC VESSEL TYPES Hopper Dredges With Working Freeboard Assignments Calculations § 174.325 Equalization...

46 CFR 174.325 - Equalization.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Equalization. 174.325 Section 174.325 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SUBDIVISION AND STABILITY SPECIAL RULES PERTAINING TO SPECIFIC VESSEL TYPES Hopper Dredges With Working Freeboard Assignments Calculations § 174.325 Equalization...

[Dynamics and combined injuries of main pest species in rice cropping zones of Yunnan, Southwest China].

PubMed

Dong, Kun; Dong, Yan; Wang, Hai-Long; Zhang, Li-Min; Zan, Qing-An; Chen, Bin; Li, Zheng-Yue

2014-01-01

A series of rice pest injuries (due to pathogens, insects, and weeds) were surveyed in 286 farmers' fields for major rice varieties of three rice cropping zones of Yunnan Province, Southwest China. The composition and dynamics of main pest species were analyzed, and the trend of rice pest succession in Yunnan was discussed based upon landmark publications. The results showed that the three rice cropping zones had different pest characteristics as regard to main species, dynamics and combined injuries. Sheath rot, bacterial leaf blight, rice stripe, leaf hoppers, armyworms and stem borers were serious in the japonica rice zone. Sheath blight and rice stripe were serious in the japonica-indica interlacing zone. Leaf blast, sheath blight, leaf folders and weeds above rice crop canopy were serious in the indica rice zone. False smut, plant hoppers and weeds below rice crop canopy were ubiquitous and serious in the three kinds of rice cropping zones. Many kinds of weed infestation emerged in the whole rice cropping seasons. Echinochloa crusgalli, Sagittaria pygmaea, Potamogeton distinctus and Spirodela polyrhiza were the main species of weeds in the rice cropping zones of Yunnan. Overall, levels of combined injuries due to pests in the japonica rice zone and the indica rice zone were higher than that in the japonica-indica interlacing zone. In terms of the trend of rice pest succession in Yunnan, injuries due to false smut, sheath blight and plant hoppers seemed to be in a worse tendency in all rice cropping zones of Yunnan, while dominants species of weeds in the paddy fields are shifting from the annual weeds to the perennial malignant weeds.

Using SPOT-5 images in rice farming for detecting BPH (Brown Plant Hopper)

NASA Astrophysics Data System (ADS)

Ghobadifar, F.; Wayayok, A.; Shattri, M.; Shafri, H.

2014-06-01

Infestation of rice plant-hopper such as Brown Plant Hopper (BPH) (Nilaparvata lugens) is one of the most notable risk in rice yield in tropical areas especially in Asia. In order to use visible and infrared images to detect stress in rice production caused by BPH infestation, several remote sensing techniques have been developed. Initial recognition of pest infestation by means of remote sensing will spreads, for precision farming practice. To address this issue, detection of sheath blight in rice farming was examined by using SPOT-5 images. Specific image indices such as Normalized decrease food production costs, limit environmental hazards, and enhance natural pest control before the problem Normalized Difference Vegetation Index (NDVI), Standard difference indices (SDI) and Ratio Vegetation Index (RVI) were used for analyses using ENVI 4.8 and SPSS software. Results showed that all the indices to recognize infected plants are significant at α = 0.01. Examination of the association between the disease indices indicated that band 3 (near infrared) and band 4 (mid infrared) have a relatively high correlation. The selected indices declared better association for detecting healthy plants from diseased ones. Consequently, these sorts of indices especially NDVI could be valued as indicators for developing techniques for detecting the sheath blight of rice by using remote sensing. This infers that they are useful for crop disease detection but the spectral resolution is probably not sufficient to distinguish plants with light infections (low severity level). Using the index as an indicator can clarify the threshold for zoning the outbreaks. Quick assessment information is very useful in precision farming to practice site specific management such as pesticide application.

Optimizing pneumatic conveying of biomass materials

NASA Astrophysics Data System (ADS)

DiCianni, Matthew Edward Michael

2011-12-01

Biomass is a readily available but underutilized energy resource. One of the main challenges is the inability of biomass feed stocks like corn stover or wood chips to flow freely without intermittent jamming. This research integrated an automated pneumatic conveying system to efficiently transport biomass into a biomass reactor. Material was held in a storage container until an end effector attached to a 3-axis controller engaged the material to flow through pneumatic vacuum in the carrier fluid of air. The material was disengaged from the carrier fluid through centripetal forces induced by a cyclone separator. As the air was pulled out of the cyclone, the biomass drops out the bottom due to gravitational forces and fell into a secondary storage hopper. The second storage container was for testing purposes only, where the actual apparatus would use a vertically oriented lock hopper to feed material into the biomass reactor. In the experimental test apparatus, sensors measured the storage hopper weight (mass-flow rate), pressure drop from the blower, and input power consumption of the motor. Parameters that were adjusted during testing include pipe diameter, material type, and motor speed. Testing indicated that decreasing the motor speed below its maximum still allows for conveyance of the material without blockage forming in the piping. The data shows that the power consumption of the system can be reduced based on the size and weight of the material introduced to the conveying pipe. Also, conveying certain materials proved to be problematic with particular duct diameters. Ultimately, an optimal duct diameter that can perform efficiently for a broad range of materials was chosen for the given system. Through these improvements, the energy return on investment will be improved for biomass feed stocks, which is taking a step in the right direction to secure the nation's energy independence.

Looking southwest at the chute leading from the coal elevator ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Looking southwest at the chute leading from the coal elevator to the conveyor belt feeding the coal storage hopper on the floor below. - Wheeling-Pittsburgh Steel Corporation, Allenport Works, Boiler House, Route 88 on West bank of Monongahela River, Allenport, Washington County, PA

Teaching with Technology. Software That's Right for You.

ERIC Educational Resources Information Center

Allen, Denise

1995-01-01

Recommends software to help teachers plan curriculum in the areas of comprehensive language arts ("Cornerstone"); writing and information ("Keroppi Day Hopper"); creative writing and imagination ("Imagination Express"); reading ("Jo-Jo's Reading Circus"); math ("Careers in Math: From Architects to Astronauts") and nature ("Eyewitness"). Provides…

Space colonization.

PubMed

2002-12-01

NASA interest in colonization encompasses space tourism; space exploration; space bases in orbit, at L1, on the Moon, or on Mars; in-situ resource utilization; and planetary terraforming. Activities progressed during 2002 in areas such as Mars colonies, hoppers, and biomass; space elevators and construction; and in-situ consumables.

Literature Review of Dredging Physical Models

DTIC Science & Technology

This U.S. Army Engineer Research and Development Center, Coastal and Hydraulics Laboratory, special report presents a review of dredging physical...one-third of the dredging performed by the U.S. Army Corps of Engineers is done by hopper dredges with dragheads. Identified research gaps include

Evacuation of coal from hoppers/silos with low pressure pneumatic blasting systems

NASA Technical Reports Server (NTRS)

Fischer, J. S.

1977-01-01

The need for an efficient, economical, effective and quiet device for moving coal and other difficult bulk solids was recognized. Thus came the advent of the low pressure pneumatic blasting system - a very efficient means of using a small amount of plant air (up to 125 PSI) to eliminate the most troublesome material hang-ups in storage containers. This simple device has one moving part and uses approximately 3% of the air consumed by a pneumatic vibrator on the same job. The principle of operation is very simple: air stored in the unit's reservoir is expelled directly into the material via a patented quick release valve. The number, size, and placement of the blaster units on the storage vessel is determined by a series of tests to ascertain flowability of the problem material. These tests in conjunction with the hopper or silo configuration determine specification of a low pressure pneumatic blasting system. This concept has often proven effective in solving flow problems when all other means have failed.

System design of a 1 MW north-facing, solid particle receiver

DOE Office of Scientific and Technical Information (OSTI.GOV)

Christian, J.; Ho, C.

Falling solid particle receivers (SPR) utilize small particles as a heat collecting medium within a cavity receiver structure. The components required to operate an SPR include the receiver (to heat the particles), bottom hopper (to catch the falling particles), particle lift elevator (to lift particles back to the top of the receiver), top hopper (to store particles before being dropped through the receiver), and ducting. In addition to the required components, there are additional features needed for an experimental system. These features include: a support structure to house all components, calibration panel to measure incident radiation, cooling loops, and sensorsmore » (flux gages, thermocouples, pressure gages). Each of these components had to be designed to withstand temperatures ranging from ambient to 700 °C. Thermal stresses from thermal expansion become a key factor in these types of high temperature systems. The SPR will be housing ~3000 kg of solid particles. The final system will be tested at the National Solar Thermal Test Facility in Albuquerque, NM.« less

System design of a 1 MW north-facing, solid particle receiver

DOE PAGES

Christian, J.; Ho, C.

2015-05-01

Falling solid particle receivers (SPR) utilize small particles as a heat collecting medium within a cavity receiver structure. The components required to operate an SPR include the receiver (to heat the particles), bottom hopper (to catch the falling particles), particle lift elevator (to lift particles back to the top of the receiver), top hopper (to store particles before being dropped through the receiver), and ducting. In addition to the required components, there are additional features needed for an experimental system. These features include: a support structure to house all components, calibration panel to measure incident radiation, cooling loops, and sensorsmore » (flux gages, thermocouples, pressure gages). Each of these components had to be designed to withstand temperatures ranging from ambient to 700 °C. Thermal stresses from thermal expansion become a key factor in these types of high temperature systems. The SPR will be housing ~3000 kg of solid particles. The final system will be tested at the National Solar Thermal Test Facility in Albuquerque, NM.« less

Fallout from the Shuttle Arm

NASA Technical Reports Server (NTRS)

1990-01-01

Vadeko International, Inc., Mississauga, Ontario developed for the Canadian National Railways (CN) the Robotic Paint Application System. The robotic paint shop has two parallel paint booths, allowing simultaneous painting of two hopper cars. Each booth has three robots, two that move along wall-mounted rails to spray-paint the exterior, a third that is lowered through a hatch in the railcar's top to paint the interior. A fully computerized system controls the movement of the robots and the painting process. The robots can do in four hours a job that formerly took 32 hours. The robotic system applies a more thorough coating and CN expects that will double the useful life of its hoppers and improve cost efficiency. Human painters no longer have to handle the difficult and hazardous job. CN paint shop employees have been retrained to operate the computer system that controls the robots. In addition to large scale robotic systems, Vadeko International is engaged in such other areas of technology as flexible automation, nuclear maintenance, underwater vehicles, thin film deposition and wide band monitoring.

DEM GPU studies of industrial scale particle simulations for granular flow civil engineering applications

NASA Astrophysics Data System (ADS)

Pizette, Patrick; Govender, Nicolin; Wilke, Daniel N.; Abriak, Nor-Edine

2017-06-01

The use of the Discrete Element Method (DEM) for industrial civil engineering industrial applications is currently limited due to the computational demands when large numbers of particles are considered. The graphics processing unit (GPU) with its highly parallelized hardware architecture shows potential to enable solution of civil engineering problems using discrete granular approaches. We demonstrate in this study the pratical utility of a validated GPU-enabled DEM modeling environment to simulate industrial scale granular problems. As illustration, the flow discharge of storage silos using 8 and 17 million particles is considered. DEM simulations have been performed to investigate the influence of particle size (equivalent size for the 20/40-mesh gravel) and induced shear stress for two hopper shapes. The preliminary results indicate that the shape of the hopper significantly influences the discharge rates for the same material. Specifically, this work shows that GPU-enabled DEM modeling environments can model industrial scale problems on a single portable computer within a day for 30 seconds of process time.

Economic feeder for recharging and ``topping off''

NASA Astrophysics Data System (ADS)

Fickett, Bryan; Mihalik, G.

2000-04-01

Increasing the size of the melt charge significantly increases yield and reduces costs. Siemens Solar Industries is optimizing a method to charge additional material after meltdown (top-off) using an external feeder system. A prototype feeder system was fabricated consisting of a hopper and feed delivery system. The low-cost feeder is designed for simple operation and maintenance. The system is capable of introducing up to 60 kg of granular silicon while under vacuum. An isolation valve permits refilling of the hopper while maintaining vacuum in the growth furnace. Using the feeder system in conjunction with Siemens Solar Industries' energy efficient hot zone dramatically reduces power and argon consumption. Throughput is also improved as faster pull speeds can be attained. The increased pull speeds have an even greater impact when the charge size is increased. Further cost reduction can be achieved by refilling the crucible after crystal growth and pulling a second ingot run. Siemens Solar Industries is presently testing the feeder in production.

FEM investigation of concrete silos damaged and reinforced externally with CFRP

NASA Astrophysics Data System (ADS)

Kermiche, Sihem; Boussaid, Ouzine; Redjel, Bachir; Amirat, Abdelaziz

2018-03-01

The present work investigates the reinforcement of concrete wheat-grain silos under initial damage. The reinforcement is achieved by mounting bands of carbon fiber reinforced polymer (CFRP) on the external walls of the silo. 4 modes of reinforcement are adapted according to the width of the band, the gap between two bands, the height of reinforcement and the number of layers achieved through banding. Analytical analyses were conducted using the Reimbert method and the Eurocode 1 Part 4 method, as well as numerically through the finite element software Abaqus. Results show that the normal pressure reaches a peak value when approaching the silo hopper. Initial damage in a concrete silo was first determined using a 3D geometrical model, while the damage analyses were conducted to optimize the CFRP reinforcement by mounting 2 CFRP bands close together above and below the cylinder-hopper joint. Increasing the number of banding layers could produce better performance as the damage was slightly decreased from 0.161 to 0.152 for 1 and 4 layers respectively.

Is Matching Innate?

PubMed Central

Gallistel, C.R; King, Adam Philip; Gottlieb, Daniel; Balci, Fuat; Papachristos, Efstathios B; Szalecki, Matthew; Carbone, Kimberly S

2007-01-01

Experimentally naive mice matched the proportions of their temporal investments (visit durations) in two feeding hoppers to the proportions of the food income (pellets per unit session time) derived from them in three experiments that varied the coupling between the behavioral investment and food income, from no coupling to strict coupling. Matching was observed from the outset; it did not improve with training. When the numbers of pellets received were proportional to time invested, investment was unstable, swinging abruptly from sustained, almost complete investment in one hopper, to sustained, almost complete investment in the other—in the absence of appropriate local fluctuations in returns (pellets obtained per time invested). The abruptness of the swings strongly constrains possible models. We suggest that matching reflects an innate (unconditioned) program that matches the ratio of expected visit durations to the ratio between the current estimates of expected incomes. A model that processes the income stream looking for changes in the income and generates discontinuous income estimates when a change is detected is shown to account for salient features of the data. PMID:17465311

Is matching innate?

PubMed

Gallistel, C R; King, Adam Philip; Gottlieb, Daniel; Balci, Fuat; Papachristos, Efstathios B; Szalecki, Matthew; Carbone, Kimberly S

2007-03-01

Experimentally naive mice matched the proportions of their temporal investments (visit durations) in two feeding hoppers to the proportions of the food income (pellets per unit session time) derived from them in three experiments that varied the coupling between the behavioral investment and food income, from no coupling to strict coupling. Matching was observed from the outset; it did not improve with training. When the numbers of pellets received were proportional to time invested, investment was unstable, swinging abruptly from sustained, almost complete investment in one hopper, to sustained, almost complete investment in the other-in the absence of appropriate local fluctuations in returns (pellets obtained per time invested). The abruptness of the swings strongly constrains possible models. We suggest that matching reflects an innate (unconditioned) program that matches the ratio of expected visit durations to the ratio between the current estimates of expected incomes. A model that processes the income stream looking for changes in the income and generates discontinuous income estimates when a change is detected is shown to account for salient features of the data.

Full-scale locomotive dynamic collision testing and correlations : offset collisions between a locomotive and a covered hopper car (test 4).

DOT National Transportation Integrated Search

2011-09-01

This report presents the test results and finite element correlations of a full-scale dynamic collision test with rail vehicles as part of the Federal Railroad Administrations research program on improved crashworthiness of locomotive structures. ...

36. BOILER HOUSE, GENERAL VIEW LOOKING TOWARD COAL CAR No. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

36. BOILER HOUSE, GENERAL VIEW LOOKING TOWARD COAL CAR No. 6 (NOTE: COAL DISTRIBUTER HOPPER & CONVEYOR THAT RUNS NORTH TO SOUTH BETWEEN TRACKS ON EAST TOWER SIDE) - Delaware County Electric Company, Chester Station, Delaware River at South end of Ward Street, Chester, Delaware County, PA

Looking East at BottomHalf of Reactor Number One and TopHalf ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Looking East at Bottom-Half of Reactor Number One and Top-Half of Reactor Number 2 Including Weigh Hopper on Third Floor of Oxide Building - Hematite Fuel Fabrication Facility, Oxide Building & Oxide Loading Dock, 3300 State Road P, Festus, Jefferson County, MO

Is Matching Innate?

ERIC Educational Resources Information Center

Gallistel, C. R.; King, Adam Philip; Gottlieb, Daniel; Balci, Fuat; Papachristos, Efstathios B.; Szalecki, Matthew; Carbone, Kimberly S.

2007-01-01

Experimentally naive mice matched the proportions of their temporal investments (visit durations) in two feeding hoppers to the proportions of the food income (pellets per unit session time) derived from them in three experiments that varied the coupling between the behavioral investment and food income, from no coupling to strict coupling.…

40 CFR 98.214 - Monitoring and QA/QC requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (for Equation U-2 of this subpart) must be determined annually from monthly measurements using the same plant instruments used for accounting purposes including purchase records or direct measurement, such as... accounting purposes including purchase records or direct measurement, such as weigh hoppers or belt weigh...

40 CFR 98.334 - Monitoring and QA/QC requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... used for accounting purposes including direct measurement weighing or through the use of purchase records same plant instruments or procedures that are used for accounting purposes (such as weigh hoppers... density and volume measurements, etc.). Record the total mass for the materials consumed each calendar...

40 CFR 98.84 - Monitoring and QA/QC requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... by direct weight measurement using the same plant instruments used for accounting purposes, such as... be determined quarterly by direct weight measurement using the same plant instruments used for accounting purposes, such as weigh hoppers, truck weigh scales, or belt weigh feeders. (f) The quantity of...

40 CFR 63.544 - Standards for process fugitive sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) Smelting furnace and dryer charging hoppers, chutes, and skip hoists; (2) Smelting furnace lead taps, and molds during tapping; (3) Smelting furnace slag taps, and molds during tapping; (4) Refining kettles; (5) Dryer transition pieces; and (6) Agglomerating furnace product taps. (b) Process fugitive emission...

Mineralogical and Geochemical Study of Titanite Associated With Copper Mineralization in the Hopper Property, Yukon Territory, Canada

NASA Astrophysics Data System (ADS)

Blumenthal, V. H.; Linnen, R. L.

2009-05-01

Copper mineralization in central Yukon is well known, but the metallogeny of the Ruby Range batholith, west of the copper belt, is poorly understood. The Hopper property, situated in the south western part of the Yukon in the Yukon-Tanana terrane, contains copper mineralization hosted by granodiorite and quartz feldspar porphyry of cal-alkaline affinity. These rock units, interpreted to be part of the Ruby Range batholith, intruded metasediments of the Ashihik Metamorphic Suite rocks. Mafic dykes cross cut the intrusion followed by aplite dykes. Small occurrences of skarn also occur in the area and some of these contain copper mineralization. The copper mineralization at the Hopper property appears to have a porphyry-type affinity. However, it is associated with a shear zone and propylitic alteration unlike other typical copper porphyry-type deposits. This raises the question whether or not the mineralization is orthomagmatic in origin, i.e., whether or not this is a true porphyry system. The main zone of mineralization is 1 kilometer long and 0.5 kilometer wide. It is characterized by disseminated chalcopyrite and pyrite, which also occur along fractures. Molybdenite mineralization was found to be associated with slickensides. Alteration minerals associated with the copper mineralization are chlorite, epidote-clinozoisite, carbonate and titanite. Chlorite and epidote-clinozoisite are concentrated in the mineralized zone, whereas an earlier potassic alteration shows a weaker spatial correlation with the mineralization. The association of the mineralization with propylitic alteration leads us to believe the mineralization is shear related, although a deeper porphyritic system may be present at depth. Two populations of titanite at the Hopper property are recognized based on their shape, size and association with other minerals. The first population, defined by a length of 100 micrometers to 1 centimeter, euhedral boundaries, and planar contacts with other magmatic phases, is interpreted to be magmatic in origin. The second population is 10 to 500 micrometers long, anhedral and shows a close association with chlorite and chalcopyrite. This type of titanite is hydrothermal in origin. Preliminary electron microprobe analyses of titanite show the magmatic titanite grains have higher concentrations of Al, Fe, Nb, Ce, Zr and Mn, and lower concentrations of Ti and Ca compared to hydrothermal titanite grains. This corresponds with substitutions of Al, Fe, Nb, and Ce to Ti and substitutions of Ce, Zr to Ca. The association of titanite with propylitic alteration and its susceptibility to trace element substitutions make this an ideal test case to evaluate magmatic versus hydrothermal titanite.

8. INTERIOR, DETAIL OF HOUSE COAL CONVEYOR IN LOADING ROOM, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

8. INTERIOR, DETAIL OF HOUSE COAL CONVEYOR IN LOADING ROOM, USED TO CONVEY COAL TO A STORAGE HOPPER AND MADE AVAILABLE TO NUTTALLBURG RESIDENTS, LOOKING WEST - Nuttallburg Mine Complex, Tipple, North side of New River, 2.7 miles upstream from Fayette Landing, Lookout, Fayette County, WV

12. Interior, boiler house, at elev. 55' looking west at ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. Interior, boiler house, at elev. 55' looking west at retired 300 lb. boilers #11, 10, and 9 with pulverized coal storage hoppers on upper left and rock coal storage bunkers on upper right. - Manchester Street Generating Station, Manchester Street Station, 460 Eddy Street, Providence, Providence County, RI

40 CFR 63.544 - Standards for process fugitive sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... National Emission Standards for Hazardous Air Pollutants from Secondary Lead Smelting § 63.544 Standards for process fugitive sources. (a) Each owner or operator of a secondary lead smelter shall control the...) Smelting furnace and dryer charging hoppers, chutes, and skip hoists; (2) Smelting furnace lead taps, and...

Sails, Wind and Water.

ERIC Educational Resources Information Center

Hubbard, Guy

1999-01-01

Discusses maritime paintings addressing such topics as why artists are attracted to sailing vessels and the content of the paintings. Includes reproductions of paintings by Edward Hopper, John H. B. Everett, Lyonel Feininger, and Willem van de Velde the Younger. Selects works to help students realize that maritime art is quite varied. (CMK)

40 CFR 98.144 - Monitoring and QA/QC requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Glass Production § 98.144 Monitoring and QA/QC requirements. (a) You must measure annual amounts of carbonate-based raw materials charged to each continuous glass... calibrated scales or weigh hoppers. Total annual mass charged to glass melting furnaces at the facility shall...

29 CFR 1910.263 - Bakery equipment.

Code of Federal Regulations, 2010 CFR

2010-07-01

... handling. (i) Wherever any of the various pieces of apparatus comprising a flour-handling system are run in... employee's hands cannot get into the hopper where they will come in contact with the in-running rolls. (2... knife head of reciprocating-blade slicers shall be provided with an interlocking arrangement so that the...

29 CFR 1910.263 - Bakery equipment.

Code of Federal Regulations, 2011 CFR

2011-07-01

... handling. (i) Wherever any of the various pieces of apparatus comprising a flour-handling system are run in... employee's hands cannot get into the hopper where they will come in contact with the in-running rolls. (2... knife head of reciprocating-blade slicers shall be provided with an interlocking arrangement so that the...

29 CFR 1910.263 - Bakery equipment.

Code of Federal Regulations, 2012 CFR

2012-07-01

... handling. (i) Wherever any of the various pieces of apparatus comprising a flour-handling system are run in... employee's hands cannot get into the hopper where they will come in contact with the in-running rolls. (2... knife head of reciprocating-blade slicers shall be provided with an interlocking arrangement so that the...

29 CFR 1910.263 - Bakery equipment.

Code of Federal Regulations, 2014 CFR

2014-07-01

... handling. (i) Wherever any of the various pieces of apparatus comprising a flour-handling system are run in... employee's hands cannot get into the hopper where they will come in contact with the in-running rolls. (2... knife head of reciprocating-blade slicers shall be provided with an interlocking arrangement so that the...

29 CFR 1910.263 - Bakery equipment.

Code of Federal Regulations, 2013 CFR

2013-07-01

... handling. (i) Wherever any of the various pieces of apparatus comprising a flour-handling system are run in... employee's hands cannot get into the hopper where they will come in contact with the in-running rolls. (2... knife head of reciprocating-blade slicers shall be provided with an interlocking arrangement so that the...

40 CFR 63.11410 - What are the compliance requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

... the proper functioning of the electronic controls for corona power and rapper operation, that the corona wires are energized, and that adequate air pressure is present on the rapper manifold. You must... integrity of corona wires, collection plates, hopper, and air diffuser plates. An initial inspection of the...

40 CFR 63.11410 - What are the compliance requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... the proper functioning of the electronic controls for corona power and rapper operation, that the corona wires are energized, and that adequate air pressure is present on the rapper manifold. You must... integrity of corona wires, collection plates, hopper, and air diffuser plates. An initial inspection of the...

40 CFR 63.10897 - What are my monitoring requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

... controls for corona power and rapper operation, that the corona wires are energized, and that adequate air... determine the condition and integrity of corona wires, collection plates, hopper, and air diffuser plates... daily inspection to verify the proper functioning of the electronic controls for corona power and rapper...

40 CFR 63.10897 - What are my monitoring requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... controls for corona power and rapper operation, that the corona wires are energized, and that adequate air... determine the condition and integrity of corona wires, collection plates, hopper, and air diffuser plates... daily inspection to verify the proper functioning of the electronic controls for corona power and rapper...

40 CFR 63.10897 - What are my monitoring requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

... controls for corona power and rapper operation, that the corona wires are energized, and that adequate air... determine the condition and integrity of corona wires, collection plates, hopper, and air diffuser plates... daily inspection to verify the proper functioning of the electronic controls for corona power and rapper...

40 CFR 63.10897 - What are my monitoring requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

... controls for corona power and rapper operation, that the corona wires are energized, and that adequate air... determine the condition and integrity of corona wires, collection plates, hopper, and air diffuser plates... daily inspection to verify the proper functioning of the electronic controls for corona power and rapper...

40 CFR 63.11410 - What are the compliance requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... the proper functioning of the electronic controls for corona power and rapper operation, that the corona wires are energized, and that adequate air pressure is present on the rapper manifold. You must... integrity of corona wires, collection plates, hopper, and air diffuser plates. An initial inspection of the...

40 CFR 63.10897 - What are my monitoring requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... controls for corona power and rapper operation, that the corona wires are energized, and that adequate air... determine the condition and integrity of corona wires, collection plates, hopper, and air diffuser plates... daily inspection to verify the proper functioning of the electronic controls for corona power and rapper...

40 CFR 63.11410 - What are the compliance requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

... the proper functioning of the electronic controls for corona power and rapper operation, that the corona wires are energized, and that adequate air pressure is present on the rapper manifold. You must... integrity of corona wires, collection plates, hopper, and air diffuser plates. An initial inspection of the...

40 CFR 63.11410 - What are the compliance requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

... the proper functioning of the electronic controls for corona power and rapper operation, that the corona wires are energized, and that adequate air pressure is present on the rapper manifold. You must... integrity of corona wires, collection plates, hopper, and air diffuser plates. An initial inspection of the...

40 CFR 98.174 - Monitoring and QA/QC requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the same plant instruments or procedures that are used for accounting purposes (such as weigh hoppers... density and volume measurements, etc.), record the totals for each process input and output for each... applicable) during the test using the same plant instruments or procedures that are used for accounting...

Track/train dynamics test report modal survey

NASA Technical Reports Server (NTRS)

Vigil, R. A.

1975-01-01

The modal survey vibration test conducted on an 80 ton open hopper freight car is described. The test data, the post-test update of the modal survey test requirements and procedure, and an index to the test data are presented. Photographs of actual measurement locations and the test historical log are included.

16 CFR 1301.3 - Findings.

Code of Federal Regulations, 2010 CFR

2010-01-01

... containers, refuse bins, buckets, boxes or hoppers, with actual internal volumes of one cubic yard or greater... containers indicate that most accidents have occurred with slant-sided metal refuse bins which are used by.... 20207. (c) Need of the public for the product and effects on utility, cost, and availability. (1) The...

Bouncing Poppers

ERIC Educational Resources Information Center

Vollmer, Michael; Möllmann, Klaus-Peter

2015-01-01

Toys are known to attract interest in physics and they are therefore often used in physics teaching of various topics. The present paper deals with a simple toy, the so-called "hopper popper," which, similar to superballs, can be used when teaching mechanics. We suggest some experiments and describe the basic physics of this toy, also…

15. BUILDING NO. 445, PHYSICS LAB (FORMERLY GUN BAG LOADING), ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

15. BUILDING NO. 445, PHYSICS LAB (FORMERLY GUN BAG LOADING), INTERIOR, FOURTH LEVEL. POWDER HOPPER AT TOP OF ELEVATOR SHAFT. POWDER DISTRIBUTED FROM HERE TO LOADING ROOMS BY TUBES. - Picatinny Arsenal, 400 Area, Gun Bag Loading District, State Route 15 near I-80, Dover, Morris County, NJ

Outbreak of Tagosodes orizicolus (Muir) in Texas rice

USDA-ARS?s Scientific Manuscript database

The rice planthopper, Tagosodes orizicolus, is reported for the first time in Texas, where it is superabundant in rice fields in four counties (Brazoria, Colorado, Harris, and Wharton). The species is a known vector of the viral disease hoja blanca, which can reduce yields up to 50%, and hopper burn...

Track/train dynamics test procedure transfer function test

NASA Technical Reports Server (NTRS)

Vigil, R. A.

1975-01-01

A transfer function vibration test was made on an 80 ton open hopper freight car in an effort to obtain validation data on the car's nonlinear elastic model. Test configuration, handling, test facilities, test operations, and data acquisition/reduction activities necessary to meet the conditions of test requirements are given.

46 CFR 44.320 - Submission of plans and calculations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Submission of plans and calculations. 44.320 Section 44.320 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LOAD LINES SPECIAL SERVICE LIMITED DOMESTIC VOYAGES Rules for Assigning Working Freeboards to Hopper Dredges § 44.320 Submission of...

46 CFR 44.320 - Submission of plans and calculations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Submission of plans and calculations. 44.320 Section 44.320 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LOAD LINES SPECIAL SERVICE LIMITED DOMESTIC VOYAGES Rules for Assigning Working Freeboards to Hopper Dredges § 44.320 Submission of...

40 CFR 98.144 - Monitoring and QA/QC requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... calibrated scales or weigh hoppers. Total annual mass charged to glass melting furnaces at the facility shall... mineral mass fractions at least annually to verify the mass fraction data provided by the supplier of the... (Reapproved 2006) Standard Test Method for Major and Minor Elements in Combustion Residues from Coal...

Prescription Opioid Abuse and Dependence: Assessment Strategies for Counselors

ERIC Educational Resources Information Center

Weigel, Daniel J.; Donovan, Kimberly A.; Krug, Kevin S.; Dixon, Wayne A.

2007-01-01

The authors review the article "Prescription Drug Use and Abuse: Risk Factors, Red Flags, and Prevention Strategies" (J. H. Isaacson, J. A. Hopper, D. P. Alford, & T. Parran, 2005), which provides an overview of the recent increase in prescription opioid abuse and dependence from the physician's perspective. In the present article, the authors…

40 CFR 98.144 - Monitoring and QA/QC requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... mineral mass fractions at least annually to verify the mass fraction data provided by the supplier of the... determine the annual average mass fraction for the carbonate-based mineral in each carbonate-based raw... calibrated scales or weigh hoppers. Total annual mass charged to glass melting furnaces at the facility shall...

40 CFR 98.144 - Monitoring and QA/QC requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... mineral mass fractions at least annually to verify the mass fraction data provided by the supplier of the... Spectrometry (incorporated by reference, see § 98.7). (c) You must determine the annual average mass fraction... calibrated scales or weigh hoppers. Total annual mass charged to glass melting furnaces at the facility shall...

Interior building details of Building D, Room DM5: mezzanine hallway, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Interior building details of Building D, Room D-M5: mezzanine hallway, intact historic asphalt surface flooring, full height partition wall with hoppers and east brick retaining wall with voids from the original veiling joist; southerly view - San Quentin State Prison, Building 22, Point San Quentin, San Quentin, Marin County, CA

Distribution of glassy-winged sharpshooter and threecornered alfalfa hopper on plant hosts in the San Joaquin valley

USDA-ARS?s Scientific Manuscript database

Homalodisca vitripennis Germar and Spissistilus festinus Say populations were surveyed bimonthly for 14 months in Kern County at five agricultural sites made up of a variety of potential host plants. Additionally, S. festinus populations were surveyed in four alfalfa fields in Kern and Tulare Counti...

Bouncing Poppers

NASA Astrophysics Data System (ADS)

Vollmer, Michael; Möllmann, Klaus-Peter

2015-11-01

Toys are known to attract interest in physics and they are therefore often used in physics teaching of various topics. The present paper deals with a simple toy, the so-called "hopper popper," which, similar to superballs, can be used when teaching mechanics. We suggest some experiments and describe the basic physics of this toy, also providing background information for teachers.

40 CFR Table 9 to Subpart Wwww of... - Initial Compliance With Work Practice Standards

Code of Federal Regulations, 2014 CFR

2014-07-01

... compression/injection molding uncover, unwrap or expose only one charge per mold cycle per compression/injection molding machine. For machines with multiple molds, one charge means sufficient material to fill... cycle per compression/injection molding machine, or prior to the loader, hoppers are closed except when...

7 CFR 58.730 - Filling containers.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Filling containers. 58.730 Section 58.730 Agriculture... Procedures § 58.730 Filling containers. Hot fluid cheese from the cookers may be held in hotwells or hoppers... shall effectively measure the desired amount of product into the pouch or container in a sanitary manner...

40 CFR Table 4 to Subpart Kkkkk of... - Requirements for Performance Tests

Code of Federal Regulations, 2010 CFR

2010-07-01

... block average pressure drop values for the three test runs, and determine and record the 3-hour block... limit for the limestone feeder setting Data from the limestone feeder during the performance test You must ensure that you maintain an adequate amount of limestone in the limestone hopper, storage bin...

Continuing Education for Texas: Special Studies of Non-Traditional Approaches to Education.

ERIC Educational Resources Information Center

Neidhart, Anthony C., Ed.

The report presents 13 studies, undertaken by Texas institutions of higher learning, responding to educational needs for improved delivery systems of higher education services to adults, and adult continuing education programs. The individual studies are: The Urban University and the Learning Society (J. E. Champagne, R. Hopper, B. Leaman); The…

Reovirus genomes from plant-feeding insects represent a newly discovered lineage within the family Reoviridae

USDA-ARS?s Scientific Manuscript database

A complex set of double-stranded RNAs (dsRNAs) was isolated from threecornered alfalfa hopper (Spissistilus festinus), a plant-feeding hemipteran pest. A subset of these dsRNAs constitute the genome of a new reovirus, provisionally designated Spissistilus festinus reovirus (SpFRV). SpFRV was prese...

Dry and Moist Idealized Experiments With a Two-Dimensional Spectral Element Model

DTIC Science & Technology

2011-01-01

Gaber ²ek ∗ UCAR/NRL, Monterey, California Francis X. Giraldo Naval Postgraduate School, Monterey, California James D. Doyle Naval Research Laboratory...Monterey, California ∗Corresponding author address: Sa²a Gaber ²ek, Naval Research Laboratory 7 Grace Hopper Avenue, Stop 2 Monterey, CA 93943-5502 E

46 CFR 45.181 - Load line exemption requirements for the Burns Harbor and Milwaukee routes.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Load line exemption requirements for the Burns Harbor... line exemption requirements for the Burns Harbor and Milwaukee routes. Barges operating on the Burns... (Milwaukee and/or Burns Harbor); (4) Design type (covered/uncovered hopper, deck, etc.); (5) External...

2. INTERIOR VIEW, LOOKING EAST, OF TRACK TWO WITH SUBASSEMBLY ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. INTERIOR VIEW, LOOKING EAST, OF TRACK TWO WITH SUBASSEMBLY OF END SECTION SHEAR PLATE FOR ROUND-SIDE HOPPER CAR (DESIGNED FOR TRANSPORT OF PLASTIC PELLETS FOR PETROCHEMICAL INDUSTRY) AND DEXTER WALTON, CLASS A WELDER. - Pullman Standard Company Plant, Fabrication Assembly Shop, 401 North Twenty-fourth Street, Bessemer, Jefferson County, AL

Catalog of Historical Seismicity in the Central United States

NASA Astrophysics Data System (ADS)

Bakun, W. H.; Hopper, M. G.

2004-05-01

Modified Mercalli intensity assignments were used to estimate source locations and moment magnitude M for eighteen 19th-century and twenty early- 20th-century earthquakes in the central United States (CUS). These solutions, comparable solutions for historical M > 6.0 CUS events (Bakun, Johnston, and Hopper, BSSA, 2003; Bakun and Hopper, BSSA, 2004), and instrumental solutions for late-20th-century events provide a uniform catalog of historical M > 5.0 CUS earthquakes. The 1811-1812 New Madrid, Missouri, (NM) earthquakes apparently dominated CUS seismicity in the first two decades of the 19th century. M5-6 NM earthquakes occurred in 1843 and 1878, but none have occurred since 1878. There has been persistent seismic activity that can be associated with faults in the Illinois Basin in Illinois and Indiana, with M > 5.0 earthquakes in 1895, 1909, 1917, 1968, and 1987. Four other M > 5.0 CUS historical earthquakes have occurred: in Kansas in 1867, in Nebraska in 1877, in Oklahoma in 1882, and in Kentucky in 1980. Ohio has also been seismically active with several 4.5 < M < 5.0 events.

Science foundation Chapter 5 Appendix 5.1: Case study marsh macroinvertebrates

USGS Publications Warehouse

Brusati, Elizabeth; Woo, Isa

2015-01-01

This case study includes representative macroinvertebrates that live in the marsh plain, its associated channels and pannes (ponds), and the marsh-upland transition zone. While less visible than animals such as birds, invertebrates play important roles in physical and biological processes (e.g., burrowing activity and channel bank erosion, and detritivores breaking down organic matter) and are important food resources for higher trophic animals. Common invertebrates in these habitats include plant-hopper (Prokelisia marginata), beach hopper (Traskorchestia traskiana), pygmy blue butterfly (Brephidium exilis), inchworm moth (Perizoma custodiata), western tanarthus beetle (Tanarthus occidentalis), salt marsh mosquitoes (Aedes spp.; Maffei 2000a, Maffei 2000b, Maffei 2000c), crabs (native Hemigrapsus oregonensis and introduced Carcinus maenas), copepods, snails (e.g. native California horn snail Cerithidea californica and introduced Ilyanassa obsoleta, Myosotella myosotis), polychaetes (e.g. Capitella spp., Eteone californica, Neanthes brandti), small clams (Macoma petalum/M. balthica), and corophiid amphipods (Cohen 2011, Race 1982, Robinson et al. 2011). Some common species were described in detail in the San Francisco Bay Goals Project Species and Community Profiles (Goals Project 2000).

Transcriptomic response of the insect vector, Peregrinus maidis, to Maize mosaic rhabdovirus and identification of conserved responses to propagative viruses in hopper vectors.

PubMed

Martin, Kathleen M; Barandoc-Alviar, Karen; Schneweis, Derek J; Stewart, Catherine L; Rotenberg, Dorith; Whitfield, Anna E

2017-09-01

Maize mosaic virus (MMV) is a plant-pathogenic rhabdovirus that is transmitted by the corn planthopper, Peregrinus maidis, in a propagative manner. P. maidis supports long-term MMV infections with no negative effects on insect performance. To elucidate whole-body transcriptome responses to virus infection, RNA-Seq was used to examine differential gene expression of virus-infected adult insects, and libraries were prepared from replicated groups of virus-exposed insects and non-exposed insects. From the 68,003 de novo-assembled transcripts, 144 were differentially-expressed (DE) during viral infection with comparable numbers up- and down-regulated. DE transcripts with similarity to genes associated with transposable elements (i.e., RNA-directed DNA polymerases) were enriched and may represent a mechanisim for modulating virus infection. Comparison of the P. maidis DE transcripts to published propagative virus-responsive transcript databases for two other hopper vectors revealed that 16% of the DE transcripts were shared across the three systems and may represent conserved responses to propagative viruses. Copyright © 2017 Elsevier Inc. All rights reserved.

Osteological postcranial traits in hylid anurans indicate a morphological continuum between swimming and jumping locomotor modes.

PubMed

Soliz, Mónica; Tulli, Maria J; Abdala, Virginia

2017-03-01

Anurans exhibit a particularly wide range of locomotor modes that result in wide variations in their skeletal structure. This article investigates the possible correlation between morphological aspects of the hylid postcranial skeleton and their different locomotor modes and habitat use. To do so, we analyzed 18 morphometric postcranial variables in 19 different anuran species representative of a variety of locomotor modes (jumper, hopper, walker, and swimmer) and habitat uses (arboreal, bush, terrestrial, and aquatic). Our results show that the evolution of the postcranial hylid skeleton cannot be explained by one single model, as for example, the girdles suggest modular evolution while the vertebral column suggests other evolutionary modules. In conjunction with data from several other studies, we were able to show a relationship between hylid morphology and habitat use; offering further evidence that the jumper/swimmer and walker/hopper locomotor modes exhibit quite similar morphological architecture. This allowed us to infer that new locomotor modalities are, in fact, generated along a morphological continuum. J. Morphol. 278:403-417, 2017. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

Reduction of Nitrogen Oxides Emissions from a Coal-Fired Boiler Unit

NASA Astrophysics Data System (ADS)

Zhuikov, Andrey V.; Feoktistov, Dmitry V.; Koshurnikova, Natalya N.; Zlenko, Lyudmila V.

2016-02-01

During combustion of fossil fuels a large amount of harmful substances are discharged into the atmospheres of cities by industrial heating boiler houses. The most harmful substances among them are nitrogen oxides. The paper presents one of the most effective technological solutions for suppressing nitrogen oxides; it is arrangement of circulation process with additional mounting of the nozzle directed into the bottom of the ash hopper. When brown high-moisture coals are burnt in the medium power boilers, generally fuel nitrogen oxides are produced. It is possible to reduce their production by two ways: lowering the temperature in the core of the torch or decreasing the excess-air factor in the boiler furnace. Proposed solution includes the arrangement of burning process with additional nozzle installed in the lower part of the ash hopper. Air supply from these nozzles creates vortex involving large unburned fuel particles in multiple circulations. Thereby time of their staying in the combustion zone is prolonging. The findings describe the results of the proposed solution; and recommendations for the use of this technological method are given for other boilers.

Automated, Quantitative Cognitive/Behavioral Screening of Mice: For Genetics, Pharmacology, Animal Cognition and Undergraduate Instruction

PubMed Central

Gallistel, C. R.; Balci, Fuat; Freestone, David; Kheifets, Aaron; King, Adam

2014-01-01

We describe a high-throughput, high-volume, fully automated, live-in 24/7 behavioral testing system for assessing the effects of genetic and pharmacological manipulations on basic mechanisms of cognition and learning in mice. A standard polypropylene mouse housing tub is connected through an acrylic tube to a standard commercial mouse test box. The test box has 3 hoppers, 2 of which are connected to pellet feeders. All are internally illuminable with an LED and monitored for head entries by infrared (IR) beams. Mice live in the environment, which eliminates handling during screening. They obtain their food during two or more daily feeding periods by performing in operant (instrumental) and Pavlovian (classical) protocols, for which we have written protocol-control software and quasi-real-time data analysis and graphing software. The data analysis and graphing routines are written in a MATLAB-based language created to simplify greatly the analysis of large time-stamped behavioral and physiological event records and to preserve a full data trail from raw data through all intermediate analyses to the published graphs and statistics within a single data structure. The data-analysis code harvests the data several times a day and subjects it to statistical and graphical analyses, which are automatically stored in the "cloud" and on in-lab computers. Thus, the progress of individual mice is visualized and quantified daily. The data-analysis code talks to the protocol-control code, permitting the automated advance from protocol to protocol of individual subjects. The behavioral protocols implemented are matching, autoshaping, timed hopper-switching, risk assessment in timed hopper-switching, impulsivity measurement, and the circadian anticipation of food availability. Open-source protocol-control and data-analysis code makes the addition of new protocols simple. Eight test environments fit in a 48 in x 24 in x 78 in cabinet; two such cabinets (16 environments) may be controlled by one computer. PMID:24637442

Automated, quantitative cognitive/behavioral screening of mice: for genetics, pharmacology, animal cognition and undergraduate instruction.

PubMed

Gallistel, C R; Balci, Fuat; Freestone, David; Kheifets, Aaron; King, Adam

2014-02-26

We describe a high-throughput, high-volume, fully automated, live-in 24/7 behavioral testing system for assessing the effects of genetic and pharmacological manipulations on basic mechanisms of cognition and learning in mice. A standard polypropylene mouse housing tub is connected through an acrylic tube to a standard commercial mouse test box. The test box has 3 hoppers, 2 of which are connected to pellet feeders. All are internally illuminable with an LED and monitored for head entries by infrared (IR) beams. Mice live in the environment, which eliminates handling during screening. They obtain their food during two or more daily feeding periods by performing in operant (instrumental) and Pavlovian (classical) protocols, for which we have written protocol-control software and quasi-real-time data analysis and graphing software. The data analysis and graphing routines are written in a MATLAB-based language created to simplify greatly the analysis of large time-stamped behavioral and physiological event records and to preserve a full data trail from raw data through all intermediate analyses to the published graphs and statistics within a single data structure. The data-analysis code harvests the data several times a day and subjects it to statistical and graphical analyses, which are automatically stored in the "cloud" and on in-lab computers. Thus, the progress of individual mice is visualized and quantified daily. The data-analysis code talks to the protocol-control code, permitting the automated advance from protocol to protocol of individual subjects. The behavioral protocols implemented are matching, autoshaping, timed hopper-switching, risk assessment in timed hopper-switching, impulsivity measurement, and the circadian anticipation of food availability. Open-source protocol-control and data-analysis code makes the addition of new protocols simple. Eight test environments fit in a 48 in x 24 in x 78 in cabinet; two such cabinets (16 environments) may be controlled by one computer.

Busy test week

NASA Image and Video Library

2012-11-08

Jason Hopper of NASA (front row), Jody Ladner of Lockheed Martin (back row, left) and Chris Mulkey of NASA prepare to test the Blue Origin BE-3 engine thrust chamber in the E-1 Test Stand Control Center at John C. Stennis Space Center on Nov. 8. The test was one of 27 conducted in Stennis' E Test Complex the week of Nov. 5.

On the Compound Questions Raised by Attempts to Quantify Conversation Analysis' Phenomena, Part I: Introduction.

ERIC Educational Resources Information Center

Weider, D. Lawrence

1993-01-01

Drummond and Hopper's article in this issue, "Back Channels Revisited," is discussed in terms of its ability to elicit contrary responses from different scholars because it incorporates elements of two incommensurate approaches to the study of conversation. Weider sets the stage for subsequent articles in this issue. (11 references) (LB)

49 CFR 231.2 - Hopper cars and high-side gondolas with fixed ends.

Code of Federal Regulations, 2010 CFR

2010-10-01

... which time they must be made to comply with the standards prescribed. (iv) Carriers are not required to... within 12 inches of a vertical plane parallel with end of car and passing through the inside face of... outer face of buffer block. (2) Carriers are not required to make changes to secure additional end...

Indians Weaving in Cyberspace Indigenous Urban Youth Cultures, Identities and Politics of Languages

ERIC Educational Resources Information Center

Jimenez Quispe, Luz

2013-01-01

This study is aimed at analyzing how contemporary urban Aymara youth hip hoppers and bloggers are creating their identities and are producing discourses in texts and lyrics to contest racist and colonial discourses. The research is situated in Bolivia, which is currently engaged in a cultural and political revolution supported by Indigenous…

49 CFR 231.2 - Hopper cars and high-side gondolas with fixed ends.

Code of Federal Regulations, 2011 CFR

2011-10-01

... car, except buffer block, brake shaft, brake wheel, brake step, or uncoupling lever shall extend to... knuckle when closed with coupler horn against the buffer block or end sill, and no other part of end of... outer face of buffer block. (2) Carriers are not required to make changes to secure additional end...

40 CFR Table 8 to Subpart Sssss of... - Continuous Compliance with Operating Limits

Code of Federal Regulations, 2011 CFR

2011-07-01

... activity level of the catalyst at least every 12 months and taking any necessary corrective action, such as... temperature measured during the most recent performance test; and vi. Checking the activity level of the... hopper. c. Maintain the limestone feeder setting at or above the level established during the most recent...

12. BUILDING 621, INTERIOR, GROUND FLOOR, LOOKING NORTHWEST AT SCREENING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. BUILDING 621, INTERIOR, GROUND FLOOR, LOOKING NORTHWEST AT SCREENING MACHINE THAT REMOVES SHELL FRAGMENTS. METALLIC DUST REMOVED BY MAGNETIC SEPERATOR UNDERNEATH SCREEN. SAWDUST IS RETURNED TO SAWDUST HOPPER BY ELEVATOR. HOODS OVER SCREENING MACHINE AT WORKBENCH REMOVE FINE SAWDUST. - Picatinny Arsenal, 600 Area, Test Areas District, State Route 15 near I-80, Dover, Morris County, NJ

49 CFR 176.97 - Prohibition of dump scows.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 2 2011-10-01 2011-10-01 false Prohibition of dump scows. 176.97 Section 176.97... Requirements for Barges § 176.97 Prohibition of dump scows. Dump scows are barges having cargo carrying compartments of the hopper type and fitted with a bottom dump or a side dump. This type of barge is prohibited...

49 CFR 176.97 - Prohibition of dump scows.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Prohibition of dump scows. 176.97 Section 176.97... Requirements for Barges § 176.97 Prohibition of dump scows. Dump scows are barges having cargo carrying compartments of the hopper type and fitted with a bottom dump or a side dump. This type of barge is prohibited...

4. DETAIL OF SMOKE GENERATOR; NORTH SIDE OF LEVEL SIX, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. DETAIL OF SMOKE GENERATOR; NORTH SIDE OF LEVEL SIX, LOOKING WEST; HICKORY SAWDUST DROPPED FROM HOPPER ONTO HEATED PLATE TO MAKE SMOKE, WHICH WAS THEN DISTRIBUTED THROUGH SQUARE DUCTS (TOP CENTER) TO INDIVIDUAL SMOKEHOUSE UNITS - Rath Packing Company, Smokehouse-Hog Chilling Building, Sycamore Street between Elm & Eighteenth Streets, Waterloo, Black Hawk County, IA

Bringing Culture to Life through Children's Literature: The Mississippi Delta in the 1930's

ERIC Educational Resources Information Center

Hopper, Peggy F.

2011-01-01

After hearing reminisces from her parents about childhood adventures that took place in the 1930's Mississippi Delta, the author, Peggy F. Hopper, decided to document these stores in two children's books, "Peggy Sue and the Pepper Patch" and "The Adventures of Theodore Roosevelt Hollumway Jones and John Hart: Chasing Bandits."…

5. INTERIOR VIEW, LOOKING WEST, ALONG ASSEMBLY LINE WITH WELDING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. INTERIOR VIEW, LOOKING WEST, ALONG ASSEMBLY LINE WITH WELDING OF THE HOPPER SIDE AND GATE FRAMES, THE FIRST ASSEMBLY OF THE SUBASSEMBLIES. STEEL FRAME (TOP OF PHOTOGRAPH) CALLED THE 'HIGHLINE,' HOLDS CRANES AND EQUIPMENT NEEDED FOR RAIL CAR ASSEMBLY. - Pullman Standard Company Plant, Fabrication Assembly Shop, 401 North Twenty-fourth Street, Bessemer, Jefferson County, AL

29 CFR 1917.49 - Spouts, chutes, hoppers, bins, and associated equipment.

Code of Federal Regulations, 2013 CFR

2013-07-01

... turned off, locked out and tagged. (3) The employee entering the bin wears a lifeline and safety harness... equipment to be used. The inspection shall include at least the eye bolts, wires, and sheaves. (2) Power... adjustments are made to a power shovel, wire, or associated equipment, the power supply to the shovel shall be...

29 CFR 1917.49 - Spouts, chutes, hoppers, bins, and associated equipment.

Code of Federal Regulations, 2012 CFR

2012-07-01

... turned off, locked out and tagged. (3) The employee entering the bin wears a lifeline and safety harness... equipment to be used. The inspection shall include at least the eye bolts, wires, and sheaves. (2) Power... adjustments are made to a power shovel, wire, or associated equipment, the power supply to the shovel shall be...

29 CFR 1917.49 - Spouts, chutes, hoppers, bins, and associated equipment.

Code of Federal Regulations, 2014 CFR

2014-07-01

... turned off, locked out and tagged. (3) The employee entering the bin wears a lifeline and safety harness... equipment to be used. The inspection shall include at least the eye bolts, wires, and sheaves. (2) Power... adjustments are made to a power shovel, wire, or associated equipment, the power supply to the shovel shall be...

50 CFR 680.23 - Equipment and operational requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... (882 lb) of crab or an alternative material supplied by the scale manufacturer on the scale under test... bottom of the hopper unless an alternative testing method is approved by NMFS. The MPE for the daily at... delivery. The scale operator may write this information on the scale printout in ink at the time of landing...

Window Operator Types | Efficient Windows Collaborative

Science.gov Websites

Types Casement Casement Casement windows are hinged at the sides. Hinged windows such as casements operating types to consider. Traditional operable window types include the projected or hinged types such as casement, awning, and hopper, and the sliding types such as double- and single-hung and horizontal sliding

75 FR 20826 - Notice of Intent To Prepare a Draft Environmental Impact Statement on Beach and Dune Restoration...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-21

... restore the beach and dune by placing approximately 610,000 cubic yards of beach compatible sand along the proposed project's beach. The sand will be hopper-dredged from a relict shoal approximately three to six... analyze the following: aesthetics/visual quality, agricultural resources, air quality, biological...

Randomized, Controlled Trial of CBT Training for PTSD Providers

DTIC Science & Technology

2013-10-01

and Therapy, 47, 902-909. Shapiro, F. (2001). Eye movement desensitization and reprocessing ( EMDR ): Basic principles...Hopper, E. K., Korn, D. L., & Simpson, W. B. (2007). A randomized clinical trial of eye movement desensitization and reprocessing ( EMDR ), fluoxetine...Josef Ruzek, Ph.D. CONTRACTING ORGANIZATION: Palo Alto Institute for Research and Education Palo Alto, CA 94304 REPORT

Going Spiral? Phenomena of "Half-Knowledge" in the Experiential Large Group as Temporary Learning Community

ERIC Educational Resources Information Center

Adlam, John

2014-01-01

In this paper I use group-analytic, philosophical and psycho-social lenses to explore phenomena associated with the convening of an experiential large group within a two-day conference on the theme of "knowing and not-knowing". Drawing in particular on the work of Earl Hopper, two different models of large group convening--in which the…

Hydrogasification reactor and method of operating same

DOEpatents

Hobbs, Raymond; Karner, Donald; Sun, Xiaolei; Boyle, John; Noguchi, Fuyuki

2013-09-10

The present invention provides a system and method for evaluating effects of process parameters on hydrogasification processes. The system includes a hydrogasification reactor, a pressurized feed system, a hopper system, a hydrogen gas source, and a carrier gas source. Pressurized carbonaceous material, such as coal, is fed to the reactor using the carrier gas and reacted with hydrogen to produce natural gas.

Strategies for Increasing IT Enrollment: Recruiting, Retaining and Encouraging the Transfer of Women and Underrepresented Groups to Four-Year Colleges

ERIC Educational Resources Information Center

Tupper, Donna Hiestand; Leitherer, Barbara; Sorkin, Sylvia; Gore, Mary Elizabeth

2010-01-01

Through the support of the National Science Foundation,, The Community College of Baltimore County has begun two separate initiatives to increase the number of women and underrepresented minorities enrolled in technological majors. Started in 2003, the Grace Hopper Scholars Program targets specifically women interested in careers in technology,…

High pressure rotary piston coal feeder

NASA Technical Reports Server (NTRS)

Gardner, J. F.; Gencsoy, H. T.; Strimbeck, D. C.

1977-01-01

This feeder concept uniquely combines the functions of solids feeding, metering, and pressurization into one compact system. Success with the rotary-piston concept would provide a lower-cost alternative to lock-hopper systems. The design of the feeder is presented, with special emphasis on the difficult problem of seal design. Initial tests will be to check seal performance. Subsequent tests will evaluate solids-feeding ability.

Novel double-stranded RNA viruses of plant-feeding insects encode a serine-alanine-proline rich protein and a polymerase distantly related to fungal viruses

USDA-ARS?s Scientific Manuscript database

Novel double stranded RNAs (~8 kbp) were isolated from the three cornered alfalfa hopper (Spissistilus festinus) and beet leafhopper (Circulifer tenellus), two plant-feeding hemipteran insect pests. Genome organization of the two new viruses, designated as Spissistilus festinus virus 1 (SpFV1) and ...

Plant-feeding insects harbor double-stranded RNA viruses encoding a novel proline-alanine rich protein and a polymerase distantly related to that of fungal viruses

USDA-ARS?s Scientific Manuscript database

Novel double-stranded RNAs (~8 kbp) were isolated from three cornered alfalfa hopper (Spissistilus festinus) and beet leafhopper (Circulifer tenellus), two plant-feeding hemipteran insect pests. Genomes of the two new viruses, designated as Spissistilus festinus virus 1 (SpFV1) and Circulifer tenell...

29 CFR 1917.49 - Spouts, chutes, hoppers, bins, and associated equipment.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the entry; and (2) The power supply to the equipment carrying the cargo to the bin shall be turned off... been notified of the entry; (2) The power supply to the equipment carrying the cargo to the bin is... adjustments are made to a power shovel, wire, or associated equipment, the power supply to the shovel shall be...

29 CFR 1917.49 - Spouts, chutes, hoppers, bins, and associated equipment.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the entry; and (2) The power supply to the equipment carrying the cargo to the bin shall be turned off... been notified of the entry; (2) The power supply to the equipment carrying the cargo to the bin is... adjustments are made to a power shovel, wire, or associated equipment, the power supply to the shovel shall be...

Resource Management for the Tagged Token Dataflow Architecture.

DTIC Science & Technology

1985-01-01

completely rigorous, formulation of the U- intepreter . 2The graph schemata presented here differ slightly from those presented in the references...Director Dr. E.B. Royce, Code 38 1 Copy Head, Research Department Naval Weapons Center China Lake, CA 93555 Dr. G. Hopper, USNR 1 Ccpy NAVDAC-OOH .O Department of the Navy " - Washington, DC 20374 .. 0 " FILMED 7-85 DTIC

New XML-Based Files: Implications for Forensics

DTIC Science & Technology

2009-04-01

previously unknown social networks.4 We can use unique identi!ers that survived copying and pasting to show plagiarism . Unique identi!ers can also raise...graduated with honors and received the Admiral Grace Murray Hopper award for academic achievement. <a:"d id=’’{985AE863-DF53-4B19-9956-91DEFC2F01C1

76 FR 59771 - Ag Processing Inc A Cooperative-Petition for Declaratory Order; Institute Proceeding and Hold...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-27

... at http://www.stb.dot.gov , under ``Information Center''/``Webcast''/``Live Video'' on the home page...) Industry practice relating to cars made overweight by snow or ice; (2) how frequently closed-hopper cars and tank cars are made overweight by snow and ice and how those cars have been brought into compliance...

Trap Model for Clogging and Unclogging in Granular Hopper Flows.

PubMed

Nicolas, Alexandre; Garcimartín, Ángel; Zuriguel, Iker

2018-05-11

Granular flows through narrow outlets may be interrupted by the formation of arches or vaults that clog the exit. These clogs may be destroyed by vibrations. A feature which remains elusive is the broad distribution p(τ) of clog lifetimes τ measured under constant vibrations. Here, we propose a simple model for arch breaking, in which the vibrations are formally equivalent to thermal fluctuations in a Langevin equation; the rupture of an arch corresponds to the escape from an energy trap. We infer the distribution of trap depths from experiments made in two-dimensional hoppers. Using this distribution, we show that the model captures the empirically observed heavy tails in p(τ). These heavy tails flatten at large τ, consistently with experimental observations under weak vibrations. But, here, we find that this flattening is systematic, which casts doubt on the ability of gentle vibrations to restore a finite outflow forever. The trap model also replicates recent results on the effect of increasing gravity on the statistics of clog formation in a static silo. Therefore, the proposed framework points to a common physical underpinning to the processes of clogging and unclogging, despite their different statistics.

TALARIS project update: Overview of flight testing and development of a prototype planetary surface exploration hopper

NASA Astrophysics Data System (ADS)

Rossi, Christopher; Cunio, Phillip M.; Alibay, Farah; Morrow, Joe; Nothnagel, Sarah L.; Steiner, Ted; Han, Christopher J.; Lanford, Ephraim; Hoffman, Jeffrey A.

2012-12-01

The TALARIS (Terrestrial Artificial Lunar And Reduced GravIty Simulator) project is intended to test GNC (Guidance, Navigation, and Control) algorithms on a prototype planetary surface exploration hopper in a dynamic environment with simulated reduced gravity. The vehicle is being developed by the Charles Stark Draper Laboratory and Massachusetts Institute of Technology in support of efforts in the Google Lunar X-Prize contest. This paper presents progress achieved since September 2010 in vehicle development and flight testing. Upgrades to the vehicle are described, including a redesign of the power train for the gravity-offset propulsion system and a redesign of key elements of the spacecraft emulator propulsion system. The integration of flight algorithms into modular flight software is also discussed. Results are reported for restricted degree of freedom (DOF) tests used to tune GNC algorithms on the path to a full 6-DOF hover-hop flight profile. These tests include 3-DOF tests on flat surfaces restricted to horizontal motion, and 2-DOF vertical tests restricted to vertical motion and 1-DOF attitude control. The results of tests leading up to full flight operations are described, as are lessons learned and future test plans.

Sky Compass Orientation in Desert Locusts-Evidence from Field and Laboratory Studies.

PubMed

Homberg, Uwe

2015-01-01

Locusts are long-range migratory insects. At high population density, immature animals form marching hopper bands while adults take off and form huge swarms of millions of animals. At low population densities animals are solitarious, but likewise migrate, mostly during the night. Numerous studies aimed at predicting locust infestations showed that migrations both as hopper bands and as adults are largely downwind following seasonal shifts of the tropical convergence zone taking the animals to areas of rainfall. Only a few studies provided evidence for active orientation mechanisms, including the involvement of a sun compass. This scarcity of evidence stands in contrast to recent neurobiological data showing sophisticated neuronal adaptations suited for sky compass navigation. These include a special dorsal eye region with photoreceptors suited to analyze the polarization pattern of the sky and a system of topographically arranged sky compass neurons in the central complex of the brain. Laboratory experiments, moreover, demonstrated polarotaxis in tethered flying animals. The discrepancy of these findings call for more rigorous field studies on active orientation mechanisms in locusts. It remains to be shown how locusts use their internal sky compass during mass migrations and what role it plays to guide solitarious locusts in their natural habitat.

Trap Model for Clogging and Unclogging in Granular Hopper Flows

NASA Astrophysics Data System (ADS)

Nicolas, Alexandre; Garcimartín, Ángel; Zuriguel, Iker

2018-05-01

Granular flows through narrow outlets may be interrupted by the formation of arches or vaults that clog the exit. These clogs may be destroyed by vibrations. A feature which remains elusive is the broad distribution p (τ ) of clog lifetimes τ measured under constant vibrations. Here, we propose a simple model for arch breaking, in which the vibrations are formally equivalent to thermal fluctuations in a Langevin equation; the rupture of an arch corresponds to the escape from an energy trap. We infer the distribution of trap depths from experiments made in two-dimensional hoppers. Using this distribution, we show that the model captures the empirically observed heavy tails in p (τ ). These heavy tails flatten at large τ , consistently with experimental observations under weak vibrations. But, here, we find that this flattening is systematic, which casts doubt on the ability of gentle vibrations to restore a finite outflow forever. The trap model also replicates recent results on the effect of increasing gravity on the statistics of clog formation in a static silo. Therefore, the proposed framework points to a common physical underpinning to the processes of clogging and unclogging, despite their different statistics.

Human hopping on damped surfaces: strategies for adjusting leg mechanics.

PubMed

Moritz, Chet T; Farley, Claire T

2003-08-22

Fast-moving legged animals bounce along the ground with spring-like legs and agilely traverse variable terrain. Previous research has shown that hopping and running humans maintain the same bouncing movement of the body's centre of mass on a range of elastic surfaces by adjusting their spring-like legs to exactly offset changes in surface stiffness. This study investigated human hopping on damped surfaces that dissipated up to 72% of the hopper's mechanical energy. On these surfaces, the legs did not act like pure springs. Leg muscles performed up to 24-fold more net work to replace the energy lost by the damped surface. However, considering the leg and surface together, the combination appeared to behave like a constant stiffness spring on all damped surfaces. By conserving the mechanics of the leg-surface combination regardless of surface damping, hoppers also conserved centre-of-mass motions. Thus, the normal bouncing movements of the centre of mass in hopping are not always a direct result of spring-like leg behaviour. Conserving the trajectory of the centre of mass by maintaining spring-like mechanics of the leg-surface combination may be an important control strategy for fast-legged locomotion on variable terrain.

Human hopping on damped surfaces: strategies for adjusting leg mechanics.

PubMed Central

Moritz, Chet T; Farley, Claire T

2003-01-01

Fast-moving legged animals bounce along the ground with spring-like legs and agilely traverse variable terrain. Previous research has shown that hopping and running humans maintain the same bouncing movement of the body's centre of mass on a range of elastic surfaces by adjusting their spring-like legs to exactly offset changes in surface stiffness. This study investigated human hopping on damped surfaces that dissipated up to 72% of the hopper's mechanical energy. On these surfaces, the legs did not act like pure springs. Leg muscles performed up to 24-fold more net work to replace the energy lost by the damped surface. However, considering the leg and surface together, the combination appeared to behave like a constant stiffness spring on all damped surfaces. By conserving the mechanics of the leg-surface combination regardless of surface damping, hoppers also conserved centre-of-mass motions. Thus, the normal bouncing movements of the centre of mass in hopping are not always a direct result of spring-like leg behaviour. Conserving the trajectory of the centre of mass by maintaining spring-like mechanics of the leg-surface combination may be an important control strategy for fast-legged locomotion on variable terrain. PMID:12965003

Design requirements, challenges, and solutions for high-temperature falling particle receivers

NASA Astrophysics Data System (ADS)

Christian, Joshua; Ho, Clifford

2016-05-01

Falling particle receivers (FPR) utilize small particles as a heat collecting medium within a cavity receiver structure. Previous analysis for FPR systems include computational fluid dynamics (CFD), analytical evaluations, and experiments to determine the feasibility and achievability of this CSP technology. Sandia National Laboratories has fabricated and tested a 1 MWth FPR that consists of a cavity receiver, top hopper, bottom hopper, support structure, particle elevator, flux target, and instrumentation. Design requirements and inherent challenges were addressed to enable continuous operation of flowing particles under high-flux conditions and particle temperatures over 700 °C. Challenges include being able to withstand extremely high temperatures (up to 1200°C on the walls of the cavity), maintaining particle flow and conveyance, measuring temperatures and mass flow rates, filtering out debris, protecting components from direct flux spillage, and measuring irradiance in the cavity. Each of the major components of the system is separated into design requirements, associated challenges and corresponding solutions. The intent is to provide industry and researchers with lessons learned to avoid pitfalls and technical problems encountered during the development of Sandia's prototype particle receiver system at the National Solar Thermal Test Facility (NSTTF).

Methods of quantitative risk assessment: The case of the propellant supply system

NASA Astrophysics Data System (ADS)

Merz, H. A.; Bienz, A.

1984-08-01

As a consequence of the disastrous accident in Lapua (Finland) in 1976, where an explosion in a cartridge loading facility killed 40 and injured more than 70 persons, efforts were undertaken to examine and improve the safety of such installations. An ammunition factory in Switzerland considered the replacement of the manual supply of propellant hoppers by a new pneumatic supply system. This would reduce the maximum quantity of propellant in the hoppers to a level, where an accidental ignition would no longer lead to a detonation, and this would drastically limit the effects on persons. A quantitative risk assessment of the present and the planned supply system demonstrated that, in this particular case, the pneumatic supply system would not reduce the risk enough to justify the related costs. In addition, it could be shown that the safety of the existing system can be improved more effectively by other safety measures at considerably lower costs. Based on this practical example, the advantages of a strictly quantitative risk assessment for the safety planning in explosives factories are demonstrated. The methodological background of a risk assessment and the steps involved in the analysis are summarized. In addition, problems of quantification are discussed.

A Basic Robotic Excavator (the Glenn Digger): Description, Design, and Initial Operation

NASA Technical Reports Server (NTRS)

Bauman, Steve; Newman, Paul; Izadnegahdar, Alain; Johnson, Kyle; Abel, Phillip

2016-01-01

This paper describes the design, commercial part selections, fabrication, assembly, installation, and initial operation of a two degree of freedom robotic excavator. Colloquially referred to as "the NASA Glenn Digger," it was designed specifically to be mounted onto, and to operate with, the then newly developed Centaur 2 robotic mobility base. The excavator, when mounted to Centaur 2, is designed to scoop loose regolith from the terrain, raise its loaded bucket up and dump the load into a hopper of at least a 1-m-height. The hopper represents the input to a machine that would process the raw material, such as to produce oxygen from lunar regolith as would be required for long-term lunar habitation. This equipment debuted at the annual Research and Technology Studies ("Desert RATS", Ref. 1) event held north of Flagstaff, Arizona, in September of 2010, when the Digger was successfully joined to Centaur 2 and the shoveling articulation was demonstrated. During 2011, the hardware was modified for added strength, strain gauges were added to measure loads, and the controls were improved in preparation for the 2011 Desert RATS event, where additional "field operations" experience was gained.

Segregating photoelastic particles in free-surface granular flows

NASA Astrophysics Data System (ADS)

Thomas, Amalia; Vriend, Nathalie; Environmental; Industrial Fluid Dynamics Team

2017-11-01

We present results from a novel experimental set-up creating 2D avalanches of photoelastic discs. Two distinct hoppers supply either monodisperse or bidisperse particles at adjustable flow-rates into a 2 meter long, narrow acrylic chute inclined at 20°. For 20-40 seconds the avalanche maintains a steady-state that accelerates and thins downstream. The chute basal roughness is variable, allowing for different flow profiles. Using a set of polarizers and a high-speed camera, we visualize and quantify the forces due to dynamic interactions between the discs using photoelastic theory. Velocity and density profiles are derived from particle tracking at different distances from the discharge point and are coarse-grained to obtain continuous fields. With the access to both force information and dynamical properties via particle-tracking, we can experimentally validate existing mu(I) and non-local rheologies. As an extension, we probe the effect of granular segregation in bimodal mixtures by using the two separate inflow hoppers. We derive the state of segregation along the avalanche channel and measure the segregation velocities of each species. This provides insight in, and a unique validation of, the fundamental physical processes that drive segregation in avalanching geometries.

Overview Of Suborbital Human Transportation Concept Alpha

NASA Astrophysics Data System (ADS)

Adirim, H.; Pilz, N.; Marini, M.; Hendrick, P.; Schmid, M.; Behr, R.; Barth, T.; Tarfeld, F.; Wiegand, A.; Charbonnier, D.; Haya Ramos, R.; Steeland, J.; Mack, A.

2011-05-01

Within the EC co-funded project FAST20XX (Future high-Altitude high-Speed Transport 20XX), the European suborbital passenger transportation system concept ALPHA (Airplane Launched PHoenix Aircraft), which shall be based to a maximum extent on existing technologies and capabilities, is currently being investigated as collaborative project by a European consortium under coordination of ESA. The ALPHA concept incorporates an air-launch from a carrier aircraft, which shall be used as first stage. The ALPHA vehicle shall be capable of transporting up to four passengers plus one pilot to an altitude of at least 100 km. The ALPHA vehicle is a down-scaled version of the suborbital space transportation concept Hopper, which was already deeply investigated within the European FESTIP System Study and the German ASTRA program including the successfully flown experimental landing demonstrator Phoenix. This approach has allowed the use of existing aerodynamic vehicle data and has led to the adaptation of the external Hopper/Phoenix configuration for ALPHA. In FESTIP and ASTRA, the Hopper configuration showed sufficient stability margins. Due to the geometric similarity of the ALPHA and Hopper vehicles, a trimable and flyable configuration could be derived by means of ALPHA flight trajectory calculations. In its current configuration, the ALPHA vehicle has a length of ca. 9 m and a gross take-off mass of ca. 3.5 Mg. The launch, staging and separation of ALPHA shall be performed either as internal air-launch from the cargo bay of the carrier aircraft, as under-wing air-launch or as towed air-launch. After separation from the carrier aircraft, the ALPHA vehicle ignites its onboard rocket propulsion system. Since conventional liquid and solid propulsion did not seem suitable for ALPHA due to Their high cost, limited safety and toxicity, a low-cost, “green” and non-hazardous hybrid propulsion system based on liquid nitrous oxide in combination with a solid polymer fuel was selected as baseline ALPHA propulsion. The general feasibility of hybrid propulsion for suborbital vehicle application with this propellant combination was already successfully demonstrated in the first reusable and privately-funded manned launch vehicle SpaceShipOne and consequently represents the solution with the lowest development risk for the investigated application. Due to the huge success of SpaceShipOne, the same type of hybrid propulsion is foreseen for Virgin Galactic’s SpaceShipTwo. ALPHA vehicle guidance will preferably be fully autonomous during the entire mission flight profile. The required technology for autonomous vehicle guidance can be adapted from the European RLV demonstrator Phoenix, which successfully demonstrated automated landing when it was dropped three times by a helicopter and landed precisely after a GPS-guided glide. This paper outlines the current status of the technology development work for ALPHA and has a special focus on aerodynamic and aerothermodynamic aspects of the concept.

Investigation of the flow characteristics of lunar regolith simulants under reduced gravity and vacuum on a partial-g parabolic flight

NASA Astrophysics Data System (ADS)

Reiss, Philipp; Hager, Philipp

2013-04-01

In the field of planetary and asteroid exploration missions, one of the main interests is to gain knowledge about the components of the local Regolith to understand the properties and formation of these objects and to possibly use bound elements for in-situ resource utilization (ISRU). The handling and transport of Regolith, especially within smaller scientific sampling devices and analysis instruments, is a central issue that is often underestimated. Due to its physical properties, lunar Regolith for instance has an increased risk of clogging conveying and processing devices and hence complicates the design of such systems. In most current concepts for lunar and Martian exploration missions, the excavated Regolith is fed to a storage or analysis instrument through a series of hoppers, pipes, and similar devices. This transport process is mainly affected by the flow characteristics of the Regolith, and reduced flowability or clogging could impact the success of any mission trying to handle, sample or process Regolith. As part of the Lunar In-situ Resource Experiment (LUISE), transport processes for lunar Regolith were examined. A series of experiments with representative funnel geometries were conducted on a partial-g parabolic flight under 0.38g Martian and 0.16g lunar gravity. The experiments aimed to examine key parameters for hopper designs used in sampling processes for science experiments or ISRU processes on Mars and Moon. Two different representative lunar Regolith simulants, JSC-1A and NU-LHT-2M, were used in the investigation (sample mass < 50g, grain size < 2mm). To avoid gas inclusions in the porous simulant material, the experiments were conducted under a low vacuum between 10-3 and 100kPa. 21 different funnel geometries with variable inclination angle and opening width were tested. They were designed similar to an hourglass, with two different funnels on each side. The material flow was initiated by turning the assembly upside-down. The inclination angles of the funnels varied from 55deg to 75deg in 5deg steps, both in symmetrical and asymmetrical configuration. Three opening widths were investigated, namely 8mm, 13mm, and 18mm. Although both simulant materials showed highly variable flow characteristics, a clear direct proportional dependence between flow rate and g-level was observed. With the transition to lower g-levels, the consolidation of the simulant was significantly reduced, so that in some cases the filling level of the respective hoppers raised and prevented further material flow. The cohesive character of both simulants mainly appeared at lunar gravity. Here the material flow of NU-LHT-2M occasionally came to a sudden stop or did not start at all. Steeper and wider hoppers in most cases lead to increased flow rates, whereas geometries with wider openings tended to reduce the flow continuity. Based on these results, guidelines can be established for designing conveying devices to be used for instruments on Mars or Moon.

Handling System for Iridium-192 Seeds

NASA Technical Reports Server (NTRS)

Carpenter, W.; Wodicka, D.

1973-01-01

A complete system is proposed for safe handling of iridium-192 seeds used to internally irradiate malignant growths. A vibratory hopper feeds the seeds onto a transport system for deposit in a magazine or storage area. A circular magazine consisting of segmented plastic tubing with holes in the walls to accommodate the seeds seems feasible. The magazine is indexed to stop and release a seed for calibration and deposition.

12. INTERIOR VIEW, FIRST FLOOR SHOWING GRINDING STONES COVERED WITH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. INTERIOR VIEW, FIRST FLOOR SHOWING GRINDING STONES COVERED WITH VATS (RIGHT STONE RUN BY 35' LEFFAL VERTICAL TURBINE; LEFT BY 23' 1EFFAL VERTICAL TURBINE). THE HOPPER ON THE VAT TO THE LEFT FUNNELS THE GRAIN IN. THE CHUTE AT THE BOTTOM OF THE CENTER VAT SENDS GROUND GRAIN TO THE CONVEYOR BELOW. - Schech's Mill, Beaver Creek State Park, La Crescent, Houston County, MN

Will There Be Enough Information Technology Managers in 2010?

DTIC Science & Technology

2006-03-08

readily identifiable generations occupying the workplace today—the Traditionalists, Baby Boomers, Generation Xers and Millennials .19 Each is “clearly...million. Generation Xers (1965-1980) are a smarter22 but very influential population at forty-six million. The Millennials (1981 to 1999) represent the...Generation X colleagues, the newest generation of workers, the Millennials , are also job hoppers.85 Because employees under 40 years old—a group

5. View from northwest corner, Spruce Street. Photo shows the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. View from northwest corner, Spruce Street. Photo shows the elevation of Buildings #6 and #1. Doors in the center of the buildings provide a passageway to the interior courtyard of the complex between Buildings #6, #5, #3, and #1. The photo illustrates the pilaster and corbeling of the walls. The photo also shows the coal hopper. - Merrill Silk Mill, 233 Canisteo Street, Hornell, Steuben County, NY

Shear Roll Mill Reactivation

DTIC Science & Technology

2012-09-13

pneumatically operated paste dumper and belt conveyor system, the loss in weight feeder system, the hydraulically operated shear roll mill, the pellet...out feed belt conveyor , and the pack out system comprised of the metal detector, scale, and pack out empty and full drum roller conveyors . Page | 4...feed hopper and conveyor supplying the loss in weight feeder were turned on, and it was verified that these items functioned as designed . The

Kinetic extruder - a dry pulverized solid material pump

DOEpatents

Meyer, John W [Palo Alto, CA; Bonin, John H [Sunnyvale, CA; Daniel, Jr., Arnold D.

1983-01-01

Method and apparatus are shown for the continuous feeding of pulverized material to a high pressure container. A rotor is located within the high pressure container. The pulverized material is fed from a feed hopper through a stationary feed pipe to a vented spin-up chamber to a plurality of two-stage sprues mounted in the rotor. Control nozzles downstream from the sprues meter the flow of coal through the sprues.

5. Photocopied August 1978. FRONT OF A HORRY ROTARY FURNACE, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. Photocopied August 1978. FRONT OF A HORRY ROTARY FURNACE, SHOWING INTERIOR ELECTRODES. THE RAW MATERIALS FOR CALCIUM CARBIDE PRODUCTION--LIMESTONE AND COKE--WERE FED BY HOPPERS PLACED BETWEEN THESE ELECTRODES INTO THE ELECTRIC ARC. THE REMOVABLE PLATES ON THE EXTERNAL CIRCUMSTANCE OF THE HORRY FURNACE ARE SHOWN ON THE FIRST THREE FURNACES. (M) - Michigan Lake Superior Power Company, Portage Street, Sault Ste. Marie, Chippewa County, MI

Assessing Impacts of Navigation Dredging on Atlantic Sturgeon (Acipenser oxyrinchus)

DTIC Science & Technology

2014-11-01

fishes and insect larvae (Smith 1985, Dadswell 2006). Shallow water shoals located adjacent to both sides of the Federal navigation channel, provide a...incision was closed using sterile resorbitive suture material with four to five simple interrupted stitches. An iodine disinfectant was applied to the...1976). Assessment of techniques used to quantify salmon smolt entrainment by a hydraulic suction hopper dredge in the Fraser River estuary. Environment

Army Corps of Engineers: Action Needed to Ensure the Quality of Maintenance Dredging Contract Cost Data

DTIC Science & Technology

2015-09-01

planning, awarding, and administering maintenance dredging contracts with industry . 8For more information on hopper dredging, see GAO, Army Corps of...miles of waterways and hundreds of ports of harbors. The Corps conducts maintenance dredging primarily under contract with private industry to...headquarters, divisions, and districts (selected for geographic variation and range of dredging work) and dredging industry stakeholders. What

Design and strength analysis of a fertilizing and soil covering vehicle

NASA Astrophysics Data System (ADS)

Sun, Heng-Hui; Zhang, Zheng-Yong; Liu, Yang; Zhu, Li-Kai; Chen, En-Wei

2018-03-01

In this paper, a kind of fertilizing and soil covering vehicle is designed with compact structure, easy control and substituting manual work to conduct the operations including fertilizing and soil covering. In accordance with movement, structure and loading feature of fertilizing and soil covering vehicle, parametric modeling is carried out for the frame part of this fertilizing and soil covering vehicle to define boundary conditions such as load, constraint, etc. when the frame is under the working condition of normal full load. ANSYS software is used to produce finite element model of frame, and to analyze and solve the model, so as to obtain stress and stain variation diagram of each part of frame under working condition of normal full load. The calculation result shows that: the structure of frame is able to meet the strength requirement, and the maximum value of stress is located at joint between frame and external hinge, which should be appropriately improved in thickening way. In addition, a larger deformation occurring at damper on lower part of hopper may be reduced by adding rib plate at damper on lower part of hopper. The research result of this paper provides the theoretical basis for the design of frame of fertilizing and soil covering vehicle, which has deep theoretical significance and application value.

Cohesion, Cracking, Dilation, and Flow -- Rheological Behavior of Cohesive Pharmaceutical Powders

NASA Astrophysics Data System (ADS)

Muzzio, Fernando

2007-03-01

Cohesive powders can be loosely defined as systems where the attractive forced between particles exceed the average particle weight. Cohesive powder flow is interesting from a wide range of reasons. Their main characteristic, intermittence, is evidenced both in the interruption of flow out of hoppers (a mundane issue causing great annoyance to industrial practitioners) and in the sudden avalanching of snow and dirt that has terrified and terrified mankind since the dawn of time. At the present time, our ability to predict either of these phenomena (and many more involving cohesive powders) is very limited, primarily due to an incomplete understanding of their constitutive behavior. To wit, consider just a simple fact: a flowing powder never has constant density. Equations describing the relationship between velocity, shear, stress, and density are rudimentary at best. Computational and experimental approaches for characterizing flow behavior are in their infancy. In this talk, I will describe some recent progress achieved at Rutgers by our group. New instruments have been developed to determine simultaneously powder density and cohesive flow effects. Extensive measurements have been carried out focusing on pharmaceutical blends. These results have been used to fine-tune computational models that accurately predict dilation, flow in drums, and flow in hoppers. Impact of these observations for pharmaceutical manufacturing applications will be discussed in some detail.

Determination of exposure to respirable quartz in the stone crushing units at Azendarian-West of Iran.

PubMed

Bahrami, Abdul Rahman; Golbabai, Faridah; Mahjub, Hossien; Qorbani, Farshid; Aliabadi, Mohsan; Barqi, Mohamadali

2008-08-01

The purpose of this study is to describe the personal exposure to respirable dust and quartz and in stone crushing units located at west of Iran. A size of 40 personal samples and 40 stationary samples were obtained and analysis was done by X-ray diffraction (XRD). The results of personal sampling were shown the concentrations of respirable dust exposure level in workers of process, hopper and drivers were 1.90, 2.22, 1.41 times greater than Occupational Safety and Health Administration permissible exposure limit (OSHA PEL). The average value of total dust and respirable dust emission from stationary sources was 9.46 mg/m(3), 1.24 mg/m(3) respectively, showing that 13.8 % of total dust is respirable. The efficiency of local exhaust ventilation (LEV) to control of particles inside of industrial units was greater than 99%. It is concluded from this research the particulate generated from stone crushing activities contain a significant amount of respirable particle. The amount of free silica in stone quartz is 85 to 97 percent that emission of particles effect to health workers. LEV has important effect in the removal of silica particles in stone crushing units. The worker of hoppers still exposed to silica more than standard limits.

Active hopper for promoting flow of bulk granular or powdered solids

DOEpatents

Saunders, Timothy; Brady, John D.

2013-04-02

An apparatus that promotes the flow of materials has a body having an inner shape for holding the materials, a wall having a shape that approximates a portion of the inner shape of the body, and a vibrator attached to the wall. The wall may be disposed vertically within the body close to the body's inner shape. The vibrator transfers vibrations to the wall to agitate the material and encourage material flow.

Thermal-hydraulics Analysis of a Radioisotope-powered Mars Hopper Propulsion System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robert C. O'Brien; Andrew C. Klein; William T. Taitano

Thermal-hydraulics analyses results produced using a combined suite of computational design and analysis codes are presented for the preliminary design of a concept Radioisotope Thermal Rocket (RTR) propulsion system. Modeling of the transient heating and steady state temperatures of the system is presented. Simulation results for propellant blow down during impulsive operation are also presented. The results from this study validate the feasibility of a practical thermally capacitive RTR propulsion system.

49 CFR 231.4 - Fixed-end low-side gondola and low-side hopper cars.

Code of Federal Regulations, 2012 CFR

2012-10-01

...) Dimensions. Same as specified for “Box and other house cars” (see § 231.1(i)(2)). (3) Location. (i) One near... are low-side cars.) (a) Hand brakes—(1) Number. Same as specified for “Box and other house cars” (see § 231.1(a)(1)). (2) Dimensions. Same as specified for “Box and other house cars” (see § 231.1(a)(2)). (3...

49 CFR 231.4 - Fixed-end low-side gondola and low-side hopper cars.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) Dimensions. Same as specified for “Box and other house cars” (see § 231.1(i)(2)). (3) Location. (i) One near... are low-side cars.) (a) Hand brakes—(1) Number. Same as specified for “Box and other house cars” (see § 231.1(a)(1)). (2) Dimensions. Same as specified for “Box and other house cars” (see § 231.1(a)(2)). (3...

49 CFR 231.4 - Fixed-end low-side gondola and low-side hopper cars.

Code of Federal Regulations, 2011 CFR

2011-10-01

...) Dimensions. Same as specified for “Box and other house cars” (see § 231.1(i)(2)). (3) Location. (i) One near... are low-side cars.) (a) Hand brakes—(1) Number. Same as specified for “Box and other house cars” (see § 231.1(a)(1)). (2) Dimensions. Same as specified for “Box and other house cars” (see § 231.1(a)(2)). (3...

14. VIEW FROM TRACK AT NORTHEAST CORNER OF THE PLANT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

14. VIEW FROM TRACK AT NORTHEAST CORNER OF THE PLANT TOWARD A COAL TRESTLE EAST OF THE PLANT. THE TRESTLE WAS ADDED IN 1910. HOPPER CARS WERE WINCHED OVER A CRUSHER LOCATED DIRECTLY UNDER THE SHED AND DUMPED. A HEATED TRACK SECTION JUST BEYOND THE SHED WAS USED TO THAW FROZEN CARS IN COLD WEATHER. - New York, New Haven & Hartford Railroad, Cos Cob Power Plant, Sound Shore Drive, Greenwich, Fairfield County, CT

Sediment Engineering thru Dredging and with Nature (SETDWN) - Fate of Fines in the Dredging and Placement Process

DTIC Science & Technology

2015-05-15

operations and beach construction perspective, material is lost and a significant percent of fines is winnowed during the dredging and placement...discharged at the beach weather it is from a hopper pumpout, cuttersuction, or hydraulic offloader; experiences similar winnowing processes. The beach...of compliance with in situ percent fines criteria. This same process can be employed for the winnowing of other constituents in mixed sediments as

Kinetic extruder - a dry pulverized solid material pump

DOEpatents

Meyer, J. W.; Bonin, J. H.; Daniel, A. D. Jr.

1983-03-15

Method and apparatus are shown for the continuous feeding of pulverized material to a high pressure container. A rotor is located within the high pressure container. The pulverized material is fed from a feed hopper through a stationary feed pipe to a vented spin-up chamber to a plurality of two-stage sprues mounted in the rotor. Control nozzles downstream from the sprues meter the flow of coal through the sprues. 19 figs.

Analysis of California Condor (Gymnogyps californianus) use of six management units using location data from global positioning system transmitters, southern California, 2004-09-Initial report

USGS Publications Warehouse

Johnson, Matthew; Kern, Jeffrey; Haig, Susan M.

2010-01-01

This report provides an analysis of California Condor (Gymnogyps californianus) space use of six management units in southern California (Hopper Mountain and Bitter Creek National Wildlife Refuges, Wildlands Conservancy-Wind Wolves Preserve, Tejon Mountain Village Specific Plan, California Condor Study Area, and the Tejon Ranch excluding Tejon Mountain Village Specific Plan and California Condor Study Area). Space use was analyzed to address urgent management needs using location data from Global Positioning System transmitters. The U.S. Fish and Wildlife Service provided the U.S. Geological Survey with location data (2004-09) for California Condors from Global Positioning System transmitters and Geographic Information System data for the six management units in southern California. We calculated relative concentration of use estimates for each management unit for each California Condor (n = 21) on an annual basis (n = 39 annual home ranges) and evaluated resource selection for the population each year using the individual as our sampling unit. The most striking result from our analysis was the recolonization of the Tejon Mountain Village Specific Plan, California Condor Study Area, and Tejon Ranch management units during 2008. During 2004-07, the home range estimate for two (25 percent) California Condors overlapped the Tejon Mountain Village Specific Plan, California Condor Study Area, and Tejon Ranch management units (n = 8), and use within the annual home range generally was bimodal and was concentrated on the Bitter Creek and Hopper Mountain National Wildlife Refuges. However, 10 (77 percent) California Condor home ranges overlapped the Tejon Mountain Village Specific Plan, California Condor Study Area, and Tejon Ranch management units during 2008 (n = 13), and by 2009, the home range of every condor carrying a Global Positioning System transmitter (n = 14) overlapped these management units. Space use was multimodal within the home range during 2008-09 and was concentrated on Hopper Mountain Refuge in the south, Bittercreek Refuge and the Wind Wolves Preserve in the northwest, and the Tejon Mountain Village Specific Plan, California Condor Study Area, and Tejon Ranch management units in the northeast. Recolonization of the Tejon Mountain Village Specific Plan, California Condor Study Area, and Tejon Ranch management units reestablished traditional condor movement and foraging patterns in southern California and provides the travel corridor (approximately 20 kilometers wide) for recolonization of the northeastern part of the species historical range.

Space Paint

NASA Technical Reports Server (NTRS)

1976-01-01

Developed at Goddard, this improved inorganic paint may help protect coastal bridges subject to extreme corrosion from seawater spray. Potassium silicate formulated into a thin waterbase binder that sprays easily, adheres readily, and can be heavily loaded with zinc particles to provide uniform coverage in a single coat. Stanford Research Institute has measured an annual market in excess of $2 billion in painting highway bridges, utility pipelines, nuclear reactors, and railcar hoppers. Other suitable markets include offshore drilling facilities, railroad bridges, and ships.

Final Environmental Assessment for the Grace Hopper Bridge Embankment Repairs at Joint Base Charleston Weapons Station, South Carolina

DTIC Science & Technology

2015-07-06

geotechnical reconunendations to aid in design of a retaining wall structure in case this alternative is considered in the future. Based on a telephone...potentially involve significant impacts on the environment must be reviewed in accordance with the National Environmental Policy Act (NEPA) and all other...Code of Federal Regulations (CFR) 989, Environmental Impact Analysis Process (EIAP). The analyses focus on the following environmental resources: noise

Characterization of Underwater Sounds Produced by Trailing Suction Hopper Dredges During Sand Mining and Pump-out Operations

DTIC Science & Technology

2014-03-01

origin and potential impacts on aquatic organisms including marine mammals (e.g., whales and seals), sea turtles , and fishes. Until recently these...species of whales and sea turtles , as well as many species of fish. Exposure to underwater sound may potentially affect communication, foraging...the audible range of several species of marine mammals such as whales and dolphins as well as sea turtles . Right (Eubalaena glacialis), humpback

31. THIS PARTIAL VIEW OF HULETT NO. 4, LOOKING WEST, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

31. THIS PARTIAL VIEW OF HULETT NO. 4, LOOKING WEST, SHOWS THE RAILS AND WHEELS WHICH PERMIT THE UNLOADERS' LATERAL MOVEMENT ALONG THE FACE OF THE DOCK. ELECTRIC SHUNT CARS, SUCH AS THE ONE SEEN HERE, SHUTTLE EMPTY RAIL CARS INTO POSITION BENEATH THE HOPPERS AND ASSEMBLE THEM INTO TRAINS WHEN THEY ARE FULL. - Pennsylvania Railway Ore Dock, Lake Erie at Whiskey Island, approximately 1.5 miles west of Public Square, Cleveland, Cuyahoga County, OH

Preventive Maintenance and Reliability Study for the Central Heating and Power Plant at Fort Wainwright, Alaska

DTIC Science & Technology

2007-09-01

replacement of truck hopper, pan conveyor , belt conveyor , dust enclosures, magnetic separator, crusher and bypass, collec- tion chutes , bucket elevator, and...respective owners. The findings of this report are not to be construed as an official Department of the Army position unless so designated by other...stopped. If such an event oc- curred in the winter, installation missions and personnel would be put at risk. The plant was redundantly designed

Preventative Maintenance and Reliability Study for the Central Heating and Power Plant at Fort Wainwright, Alaska

DTIC Science & Technology

2007-09-01

replacement of truck hopper, pan conveyor , belt conveyor , dust enclosures, magnetic separator, crusher and bypass, collec- tion chutes , bucket elevator, and...respective owners. The findings of this report are not to be construed as an official Department of the Army position unless so designated by other...stopped. If such an event oc- curred in the winter, installation missions and personnel would be put at risk. The plant was redundantly designed

16. THREEQUARTER VIEW TAKEN FROM THE REAR OF A HULETT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

16. THREE-QUARTER VIEW TAKEN FROM THE REAR OF A HULETT ORE UNLOADER AS IT DESCENDS INTO THE HOLD. THE WALKING BEAM AND ITS GRAB BUCKET ARE OPERATED BY MEANS OF ROPES WOUND ON DRUMS, WHICH IN TURN ARE GEARED TO ELECTRIC MOTORS. ROUND TRIP FROM BOAT TO HOPPER CAN BE MADE IN 50 SECONDS. - Pennsylvania Railway Ore Dock, Lake Erie at Whiskey Island, approximately 1.5 miles west of Public Square, Cleveland, Cuyahoga County, OH

Intra- and inter-unit variation in fly ash petrography and mercury adsorption: Examples from a western Kentucky power station

USGS Publications Warehouse

Hower, J.C.; Finkelman, R.B.; Rathbone, R.F.; Goodman, J.

2000-01-01

Fly ash was collected from eight mechanical and 10 baghouse hoppers at each of the twin 150-MW wall-fired units in a western Kentucky power station. The fuel burned at that time was a blend of many low-sulfur, high-volatile bituminous Central Appalachian coals. The baghouse ash showed less variation between units than the mechanical hoppers. The mechanical fly ash, coarser than the baghouse ash, showed significant differences in the amount of total carbon and in the ratio of isotropic coke to both total carbon and total coke - the latter excluding inertinite and other unburned, uncoked coal. There was no significant variation in proportions of inorganic fly ash constituents. The inter-unit differences in the amount and forms of mechanical fly ash carbon appear to be related to differences in pulverizer efficiency, leading to greater amounts of coarse coal, therefore unburned carbon, in one of the units. Mercury capture is a function of both the total carbon content and the gas temperature at the point of fly ash separation, mercury content increasing with an increase in carbon for a specific collection system. Mercury adsorption on fly ash carbon increases at lower flue-gas temperatures. Baghouse fly ash, collected at a lower temperature than the higher-carbon mechanically separated fly ash, contains a significantly greater amount of Hg.

Association of the sites of heavy metals with nanoscale carbon in a Kentucky electrostatic precipitator fly ash

DOE Office of Scientific and Technical Information (OSTI.GOV)

James C. Hower; Uschi M. Graham; Alan Dozier

2008-11-15

A combination of high-resolution transmission electron microscopy, scanning transmission electron microscopy, and electron energy-loss spectroscopy (HRTEM-STEM-EELS) was used to study fly ashes produced from the combustion of an eastern Kentucky coal at a southeastern-Kentucky wall-fired pulverized coal utility boiler retrofitted for low-NOx combustion. Fly ash was collected from individual hoppers in each row of the electrostatic precipitators (ESP) pollution-control system, with multiple hoppers sampled within each of the three rows. Temperatures within the ESP array range from about 200 {degree}C at the entry to the first row to <150{degree}C at the exit of the third row. HRTEM-STEM-EELS study demonstrated themore » presence of nanoscale (10 s nm) C agglomerates with typical soot-like appearance and others with graphitic fullerene-like nanocarbon structures. The minute carbon agglomerates are typically juxtaposed and intergrown with slightly larger aluminosilicate spheres and often form an ultrathin halo or deposit on the fly ash particles. The STEM-EELS analyses revealed that the nanocarbon agglomerates host even finer (<3 nm) metal and metal oxide particles. Elemental analysis indicated an association of Hg with the nanocarbon. Arsenic, Se, Pb, Co, and traces of Ti and Ba are often associated with Fe-rich particles within the nanocarbon deposits. 57 refs., 5 figs.« less

Silencing of ACO decreases reproduction and energy metabolism in triazophos-treated female brown plant hoppers, Nilaparvata lugens Stål (Hemiptera: Delphacidae).

PubMed

Liu, Zong-Yu; Jiang, Yi-Ping; Li, Lei; You, Lin-Lin; Wu, You; Xu, Bin; Ge, Lin-Quan; Wu, Jin-Cai

2016-03-01

The brown plant hopper (BPH), Nilaparvata lugens Stål (Hemiptera: Delphacidae), is a major pest affecting rice in Asia, and outbreaks of this pest are closely linked to pesticide-induced stimulation of reproduction. Therefore, the BPH is a classic example of a resurgent pest. However, the effects of different genes on the regulation of pesticide-induced reproductive stimulation in the BPH are unclear. In this study, the regulatory effects of acyl-coenzyme A oxidase (ACO) on the reproduction and biochemistry of the BPH were investigated with gene silencing. The number of eggs laid per female by triazophos (TZP)+dsACO BPH females was significantly lower than those of TZP-treated (without ACO silencing) or TZP+GFP females (negative control), with the number of eggs decreasing by 30.8% (from 529.5 to 366.3) and 32.0% (from 540.5 to 366.3), respectively. The preoviposition period, oviposition period, and longevity of the TZP-treated females were also influenced by dsACO treatment. Additionally, the amounts of crude fat, protein, and some fatty acids (oleic acid, palmitic acid, linoleic acid, stearic acid, and myristoleic acid) in TZP+dsACO females were significantly lower than in TZP-treated females. Thus, ACO is one of the key genes regulating the TZP-induced stimulation of reproduction in BPH females. Copyright © 2015 Elsevier Inc. All rights reserved.

Phloem-exudate proteome analysis of response to insect brown plant-hopper in rice.

PubMed

Du, Ba; Wei, Zhe; Wang, Zhanqi; Wang, Xiaoxiao; Peng, Xinxin; Du, Bo; Chen, Rongzhi; Zhu, Lili; He, Guangcun

2015-07-01

Brown plant-hopper (Nilaparvata lugens Stål, BPH), one of the most devastating agricultural insect pests of rice throughout Asia, ingests nutrients from rice sieve tubes and causes a dramatic yield loss. Planting resistant variety is an efficient and economical way to control this pest. Understanding the mechanisms of host resistance is extremely valuable for molecular design of resistant rice variety. Here, we used an iTRAQ-based quantitative proteomics approach to perform analysis of protein expression profiles in the phloem exudates of BPH-resistant and susceptible rice plants following BPH infestation. A total of 238 proteins were identified, most of which were previously described to be present in the phloem of rice and other plants. The expression of genes for selected proteins was confirmed using a laser capture micro-dissection method and RT-PCR. The mRNAs for three proteins, RGAP, TCTP, and TRXH, were further analyzed by using in situ mRNA hybridization and localized in the phloem cells. Our results showed that BPH feeding induced significant changes in the abundance of proteins in phloem sap of rice involved in multiple pathways, including defense signal transduction, redox regulation, and carbohydrate and protein metabolism, as well as cell structural proteins. The results presented provide new insights into rice resistance mechanisms and should facilitate the breeding of novel elite BPH-resistant rice varieties. Copyright © 2015 Elsevier GmbH. All rights reserved.

View north towards yard Triple Stub Switch in foreground. The ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View north towards yard Triple Stub Switch in foreground. The three tracks lead into the East Railroad's Shop complex and Roundhouse. The Steel Hopper Car was used to haul coal and was in the process of being rebuilt but in 1956, when the railroad ended freight operations. As a result it was never completed and was left outside - East Broad Top Railroad & Coal Company, State Route 994, West of U.S. Route 522, Rockhill Furnace, Huntingdon County, PA

Continuous Removal of Coal-Gasification Residue

NASA Technical Reports Server (NTRS)

Collins, Earl R., Jr.; Suitor, J.; Dubis, D.

1986-01-01

Continuous-flow hopper processes solid residue from coal gasification, converting it from ashes, cinders, and clinkers to particles size of sand granules. Unit does not require repeated depressurization of lockhopper to admit and release materials. Therefore consumes less energy. Because unit has no airlock valves opened and closed repeatedly on hot, abrasive particles, subjected to lesser wear. Coal-gasification residue flows slowly through pressure-letdown device. Material enters and leaves continuously. Cleanout door on each pressure-letdown chamber allows access for maintenance and emergencies.

Use of an Acoustic Camera to Evaluate the Performance of Tickler Chains and Draghead Deflectors for Sea Turtle Protection during Hopper Dredging in the United States of America

DTIC Science & Technology

2018-05-01

performance nor effectiveness in protecting sea turtles has been documented.This study was the first step in evaluating TTC as a potential replacement for...draghead turtle deflectors. The primary objective was to evaluate and document operational performance of this technology, not effectiveness of reducing...incidental take. TTC operational performance was monitored using underwater camera systems over a short period of time whereas effectiveness for

Prevention of Freezing and other Cold Weather Problems at Wastewater Treatment Facilities.

DTIC Science & Technology

1985-07-01

an Archimedes screw conveyor is used to lift grit out of the sub- merged hopper. Initially, the conveyor was exposed and froze completely every...particular facility includes two primary clarifiers (in paral- lel), Archimedes screw pumps to lift wastewater to the top of the trickling filter...gal. of oil each and it takes much time to drain these gear boxes. At the headworks, an Archimedes screw is used to [if t the grit out of a submerged

Solid handling valve

DOEpatents

Williams, William R.

1979-01-01

The present invention is directed to a solids handling valve for use in combination with lock hoppers utilized for conveying pulverized coal to a coal gasifier. The valve comprises a fluid-actuated flow control piston disposed within a housing and provided with a tapered primary seal having a recessed seat on the housing and a radially expandable fluid-actuated secondary seal. The valve seals are highly resistive to corrosion, erosion and abrasion by the solids, liquids, and gases associated with the gasification process so as to minimize valve failure.

Means and apparatus for throttling a dry pulverized solid material pump

DOEpatents

Meyer, J. W.; Daniel, Jr, A. D.; Bonin, J. H.

1982-12-07

Method and apparatus are shown for control of continuous feeding of pulverized material to a high pressure container. A rotor is located within the high pressure container. The pulverized material is fed from a feed hopper through a stationary feed pipe to a vented spin-up zone chamber to a plurality of sprues mounted in the rotor. Control of the pressure within control nozzles downstream from the sprues adjusts the flow rate of coal through the sprues. 9 figs.

Means and apparatus for throttling a dry pulverized solid material pump

DOEpatents

Meyer, John W [Palo Alto, CA; Daniel, Jr., Arnold D.; Bonin, John H [Sunnyvale, CA

1982-01-01

Method and apparatus are shown for control of continuous feeding of pulverized material to a high pressure container. A rotor is located within the high pressure container. The pulverized material is fed from a feed hopper through a stationary feed pipe to a vented spin-up zone chamber to a plurality of sprues mounted in the rotor. Control of the pressure within control nozzles downstream from the sprues adjusts the flow rate of coal through the sprues.

Demonstration of Regenerable, Large-Scale Ion Exchange System Using WBA Resin in Rialto, CA

DTIC Science & Technology

2012-12-01

requirements. The system also has the flexibility to manually modify system parameters such as flow rates, pH set points, time cycles, etc. The system... flexibility to produce soda ash solutions that vary in concentration from 1 to 10% dry soda ash. The packaged soda ash system was engineered and...The dry soda ash was conveyed to a storage hopper (39.5 ft3) using a flexible screw conveyer. Soda ash solutions were prepared in a 100 gallon

State of the Art for Design and Construction of Sand Compaction Piles

DTIC Science & Technology

1987-11-01

Walz, Headquarters, US Army Corps of Engineers (HQUSACE), was REMR Technical Monitor. The REMR Overview Committee, consisted of Mr. John R. Nikel ... Wire Vibrator Hopper Casing Pipe Air Line Power Line Sand Skip Bucket Front End Loader Figure 2. Typical equipment used to construct a sand...8217~~~~--­ Rubber Packing Wire Inlet for air to close valve and press sand down ..,...__ Air lnl~ot: Figure 5. Special valve used to seal the casing when

Electrostatics effects in granular materials

NASA Astrophysics Data System (ADS)

Sarkar, Saurabh; Chaudhuri, Bodhisattwa

2013-06-01

This purpose of this study is to investigate the role of physiochemical properties and operational conditions in determining the electrostatic interactions between two species on a surface under typical industrial conditions. The variables considered for the study were particle type, particle size and shape, loading mass, surface type, angle of inclination of chute, nature and concentration of additive. Triboelectrification of simple and binary mixtures in a simple hopper and chute geometry was observed to be strongly linked to work function and moisture content of the powdered material.

Development of guidelines for optimum baghouse fluid-dynamic-system design. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eskinazi, D.; Gilbert, G.B.

1982-06-01

In recent years, the utility industry has turned to fabric filters as an alternative technology to electrostatic precipitators for particulate emission control from pulverized coal-fired power plants. One aspect of baghouse technology which appears to be of major importance in minimizing the size, cost, and operating pressure drop is the development of ductwork and compartment designs which achieve uniform gas and dust flow distribution to individual compartments and bags within a compartment. The objective of this project was to perform an experimental modeling program to develop design guidelines for optimizing the fluid mechanic performance of baghouses. Tasks included formulation ofmore » the appropriate modeling techniques for analysis of the flow of dust-laden gas through the collector system and extensive experimental analysis of fabric filter duct system design. A matrix of geometric configurations and operating conditions was experimentally investigated to establish the characteristics of an optimum system, to identify the level of fluid mechanic sophistication in current designs, and to experimentally develop new ideas and improved designs. Experimental results indicate that the design of the inlet and outlet manifolds, hopper entrance, hopper region below the tubesheet, and the compartment outlet have not been given sufficient attention. Unsteady flow patterns, poor velocity profiles, recirculation zones, and excessive pressure losses may be associated with these regions. It is evident from the results presented here that the fluid mechanic design of fabric filter systems can be improved significantly.« less

Estimation of the Age and Amount of Brown Rice Plant Hoppers Based on Bionic Electronic Nose Use

PubMed Central

Xu, Sai; Zhou, Zhiyan; Lu, Huazhong; Luo, Xiwen; Lan, Yubin; Zhang, Yang; Li, Yanfang

2014-01-01

The brown rice plant hopper (BRPH), Nilaparvata lugens (Stal), is one of the most important insect pests affecting rice and causes serious damage to the yield and quality of rice plants in Asia. This study used bionic electronic nose technology to sample BRPH volatiles, which vary in age and amount. Principal component analysis (PCA), linear discrimination analysis (LDA), probabilistic neural network (PNN), BP neural network (BPNN) and loading analysis (Loadings) techniques were used to analyze the sampling data. The results indicate that the PCA and LDA classification ability is poor, but the LDA classification displays superior performance relative to PCA. When a PNN was used to evaluate the BRPH age and amount, the classification rates of the training set were 100% and 96.67%, respectively, and the classification rates of the test set were 90.67% and 64.67%, respectively. When BPNN was used for the evaluation of the BRPH age and amount, the classification accuracies of the training set were 100% and 48.93%, respectively, and the classification accuracies of the test set were 96.67% and 47.33%, respectively. Loadings for BRPH volatiles indicate that the main elements of BRPHs' volatiles are sulfur-containing organics, aromatics, sulfur- and chlorine-containing organics and nitrogen oxides, which provide a reference for sensors chosen when exploited in specialized BRPH identification devices. This research proves the feasibility and broad application prospects of bionic electronic noses for BRPH recognition. PMID:25268913

Mechanisms of midsession reversal accuracy: Memory for preceding events and timing.

PubMed

Smith, Aaron P; Beckmann, Joshua S; Zentall, Thomas R

2017-01-01

The midsession reversal task involves a simultaneous discrimination between 2 stimuli (S1 and S2) in which, for the first half of each session, choice of S1 is reinforced and, for the last half, choice of S2 is reinforced. On this task, pigeons appear to time the occurrence of the reversal rather than using feedback from previous trials, resulting in increased numbers of errors. In the present experiments, we tested the hypothesis that pigeons make so many errors because they fail to remember the last response made and/or the consequence of making that response both of which are needed ideally as cues to respond on the next trial. To facilitate memory, during the 5-s intertrial interval, we differentially lit a houselight correlated with the prior response to S1 or S2 and maintained the hopper light when that response was correct. A control group received uncorrelated houselights and no maintained hopper light. To test for continued use of temporal information, both groups received probe sessions in which the intertrial interval was either halved or doubled. Providing relevant reminder cues of the stimulus chosen and its consequence resulted in improved reversal accuracy and reduced disruption from probe sessions compared with irrelevant cues. Nevertheless, despite the reminder cues, the pigeons in both groups appeared to continue to time the point in the session at which the reversal occurred. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Dredging Operations Technical Support Program: Engineering Design and Environmental Assessment of Dredged Material Overflow from Hydraulically Filled Hopper Barges in Mobile Bay, Alabama

DTIC Science & Technology

1990-09-01

turbid estuarine habitats such as Mobile Bay are very tolerant of moderately high concentrations of suspended sediments and thin layers of sediment...GULF OF MEXIC BAYOU 4M 2CAE SI2LTK Fiur 3. DsrbuinoAedmnTyesi oie a fo IsphordingLT anCLmb190 PART III: DREDGING EQUIPMENT AND OPERATIONAL TECHNIQUES...increase in ambient turbidity was noted. Water samples were collected at surface, middepth, and bottom. The sampling boats proceeded across their

13. VIEW OF FIRST FLOOR, LOOKING NORTHWEST. AT LEFT IS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. VIEW OF FIRST FLOOR, LOOKING NORTHWEST. AT LEFT IS A 'EUREKA O.K.' BAGGING SCALE (S. Howe Co., Silver Creek, New York). THE SUSPENSION-TYPE HOPPER SCALE WEIGHS BULK FEED AS IT DESCENDS INTO A BAG SECURED BY THE RING AT THE BASE OF THE SCALE. AT RIGHT, FINISHED PRODUCTS ARE READY FOR SALE. AT CENTER REAR IS ONE OF THE MILL'S TWO VERTICAL TWIN-SPIRAL MIXERS. Photographer: Jet T. Lowe, 1985 - Alexander's Grist Mill, Lock 37 on Ohio & Erie Canal, South of Cleveland, Valley View, Cuyahoga County, OH

Conceptual Design of a Basic Production Facility for the XM587E2/XM724 Electronic Time Fuzes

DTIC Science & Technology

1977-11-01

blue side up, and then staked. The spri.ng pin is pressed in position and probed for the 1. 644-0. 010- inch dimension. See figure 33. 4.6.7.2 Parts...fitting subassembly. The detonator 69 IDLE HOPPER FEED -PROBE STAKE SPRING PIN PROBE PRESENCE STAKE LEADL IPROB LEADID ~ ASSEMBLY14 3 1 BLUE SIDE UP...automatic shutoffs. * Warning lights /alarms/ signs /’Jecals where necessary. * Electrical grounding of machine. [ 98 0 Noise levels below 85 decibals at

6. Photocopied August 1978. LINEUP OF HORRY ROTARY FURNACES ON ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. Photocopied August 1978. LINE-UP OF HORRY ROTARY FURNACES ON THE SECOND FLOOR OF THE MICHIGAN LAKE SUPERIOR POWER COMPANY POWER HOUSE. THE HOPPERS WHICH FED THE RAW MATERIALS INTO THE FURNACES ARE SHOWN ABOVE THE FURNACES. AS THE 'SPOOL' OF THE FURNACE ROTATED PAST THE ELECTRODES PLATES WERE ADDED TO HOLD THE FINISHED PRODUCT AND THE DESCENDING RAW MATERIALS IN PLACE. THE DIRECTION OF ROTATION OF THE FURNACES SHOWN IN THIS PHOTO IS CLOCKWISE, (M). - Michigan Lake Superior Power Company, Portage Street, Sault Ste. Marie, Chippewa County, MI

The impacts of climate change on calcareous grasslands. II. Preliminary results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Masters, G.J.; Clarke, I.P.; Brown, V.K.

1995-06-01

Field manipulations of winter temperature and summer rainfall have been in operation since Feb. 1994. Monitoring of the two factorial experiments began in April 1994 and has continued at regular intervals to date. Pre-treatment characterization of all plots was completed at the northern (Buxton) and southern (Wytham) sites. The vegetation was sampled by point and 1m{sup 2} permanent quadrats. D-vac suction was used to sample the invertebrate community. Additionally, the leaf miners, spiders and Auchenorrhyncha (leaf hoppers) have been chosen for further study. At both sites, winter warming promoted plant growth, especially of the perennial grasses. However, species specific responsesmore » were recorded in terms of early growth and flowering. Drought inhibited and enhanced rainfall promoted plant growth during the summer. Drought responses were greater at Buxton, while watering had a greater impact at Wytham. Tap-rooted species were resistant to drought at both sites, while responding positively (Buxton) or showing no response (Wytham) to enhanced rainfall. The invertebrates parallelled the responses of the vegetation. Warming resulted in either increased density (Wytham) or earlier emergence (Buxton & Wytham). At Buxton, warming promoted the development of certain leaf miner species while the reverse occurred at Wytham. Impacts of winter warming on over-wintering strategies may govern such responses. Some Auchenorrhyncha species had greater densities on droughted plots at Wytham. These hoppers may be responding to increased nutrients, within host plants, due to drought. Such results give an insight into how grassland ecosystems may be modified by a changing climate.« less

Collective motion in animal groups

NASA Astrophysics Data System (ADS)

Couzin, Iain

2004-03-01

In recent years there has been a growing interest in the relationship between individual behavior and population-level properties in animal groups. One of the fundamental problems is related to spatial scale; how do interactions over a local range result in population properties at larger, averaged, scales, and how can we integrate the properties of aggregates over these scales? Many group-living animals exhibit complex, and coordinated, spatio-temporal patterns which despite their ubiquity and ecological importance are very poorly understood. This is largely due to the difficulties associated with quantifying the motion of, and interactions among, many animals simultaneously. It is on how these behaviors scale to collective behaviors that I will focus here. Using a combined empirical approach (using novel computer vision techniques) and individual-based computer models, I investigate pattern formation in both invertebrate and vertebrate systems, including - Collective memory and self-organized group structure in vertebrate groups (Couzin, I.D., Krause, J., James, R., Ruxton, G.D. & Franks, N.R. (2002) Journal of Theoretical Biology 218, 1-11. (2) Couzin, I.D. & Krause, J. (2003) Advances in the Study of Behavior 32, 1-75. (3) Hoare, D.J., Couzin, I.D. Godin, J.-G. & Krause, J. (2003) Animal Behaviour, in press.) - Self-organized lane formation and optimized traffic flow in army ants (Couzin, I.D. & Franks, N.R. (2003) Proceedings of the Royal Society of London, Series B 270, 139-146) - Leadership and information transfer in flocks, schools and swarms. - Why do hoppers hop? Hopping and the generation of long-range order in some of the largest animal groups in nature, locust hopper bands.

33. VIEW OF BASEMENT UNDER EAST BOILER ROOM LOOKING TOWARD ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

33. VIEW OF BASEMENT UNDER EAST BOILER ROOM LOOKING TOWARD WEST BOILER ROOM BASEMENT THROUGH THE ASH TRANSFER TUNNEL. ASH HOPPER FOR BOILER 900 IS ON THE RIGHT. NOTE THE TRACKS ALONG THE FLOOR OF THE TUNNEL. A SMALL ELECTRIC LOCOMOTIVE HAULED CARS FOR TRANSFERRING ASH FROM BOILERS TO DISPOSAL SITES OUTSIDE THE BUILDING. THIS SYSTEM BECAME OBSOLETE IN 1938 WHEN BOILERS IN THE WEST BOILER ROOM WERE REMOVED AND PULVERIZED COAL WAS ADOPTED AS THE FUEL. - New York, New Haven & Hartford Railroad, Cos Cob Power Plant, Sound Shore Drive, Greenwich, Fairfield County, CT

Track/train dynamics test report transfer function test. Volume 1: Test

NASA Technical Reports Server (NTRS)

Vigil, R. A.

1975-01-01

A description is presented of the transfer function test performed on an open hopper freight car loaded with 80 tons of coal. Test data and a post-test update of the requirements document and test procedure are presented. Included are a statement of the test objective, a description of the test configurations, test facilities, test methods, data acquisition/reduction operations, and a chronological test summary. An index to the data for the three test configurations (X, Y, and Z-axis tests) is presented along with test sequence, run number, test reference, and input parameters.

Physical factors affecting the mutagenicity of fly ash from a coal-fired power plant.

PubMed

Fisher, G L; Chrisp, C E; Raabe, O G

1979-05-25

The two finest, most respirable coal fly ash fractions collected from the smokestack of a power plant were more mutagenic than two coarser fractions. Mutagenicity was evaluated in the histidine-requiring bacterial strains TA 1538, TA 98, and TA 100 of Salmonella typhimurium. Ash samples collected from the hoppers of an electrostatic precipitator in the plant were not mutagenic. The mutagens in coal fly ash were resistant to x-ray or ultraviolet irradiation, possibly as a result of stabilization by fly ash surfaces. All mutagenic activity is lost with heating to 350 degrees C.

Density waves in granular flow

NASA Astrophysics Data System (ADS)

Herrmann, H. J.; Flekkøy, E.; Nagel, K.; Peng, G.; Ristow, G.

Ample experimental evidence has shown the existence of spontaneous density waves in granular material flowing through pipes or hoppers. Using Molecular Dynamics Simulations we show that several types of waves exist and find that these density fluctuations follow a 1/f spectrum. We compare this behaviour to deterministic one-dimensional traffic models. If positions and velocities are continuous variables the model shows self-organized criticality driven by the slowest car. We also present Lattice Gas and Boltzmann Lattice Models which reproduce the experimentally observed effects. Density waves are spontaneously generated when the viscosity has a nonlinear dependence on density which characterizes granular flow.

Study of Electro-Cyclonic Filtration and Pneumatic Transfer of Lunar Regolith Simulants under 1/6-g and 1-g Gravity Conditions

NASA Technical Reports Server (NTRS)

Mantovani, James G.; Townsend, Ivan I.; Mueller, Robert P.

2009-01-01

NASA has built a prototype oxygen production plant to process the lunar regolith using the hydrogen reduction chemical process. This plant is known as "ROxygen - making oxygen from moon rocks". The ROxygen regolith transfer team has identified the flow and transfer characteristics of lunar regolith simulant to be a concern for lunar oxygen production efforts. It is important to ISRU lunar exploration efforts to develop hardware designs that can demonstrate the ability to flow and transfer a given mass of regolith simulant to a desired vertical height under lunar gravity conditions in order to introduce it into a reactor. We will present results obtained under both 1/6-g and 1-g gravity conditions for a system that can pneumatically convey 16.5 kg of lunar regolith simulant (NU-LHT-2M, Mauna Kea Tephra, and JSC-1A) from a flat-bottom supply hopper to a simulated ISRU reactor (dual-chambered receiving hopper) where the granular material is separated from the convey gas (air) using a series of cyclone separators, one of which is an electrically enhanced cyclone separator (electrocyclone). The results of our study include (1) the mass flow rate as a function of input air pressure for lunar regolith simulants that are conveyed pneumatically as a dusty gas in a vertical direction against gravity under lunar gravity conditions (for NU-LHT-2M and Mauna Kea Tephra), and under earth gravity conditions (for NU-LHT-2M, Mauna Kea Tephra and JSC-1A), and (2) the efficiency of the cyclone/electrocyclone filtration system in separating the convey gas (air) from the granular particulates as a function of particle size.

Insights into the structure-function relationship of brown plant hopper resistance protein, Bph14 of rice plant: a computational structural biology approach.

PubMed

Gupta, Manoj Kumar; Vadde, Ramakrishna; Donde, Ravindra; Gouda, Gayatri; Kumar, Jitendra; Nayak, Subhashree; Jena, Mayabini; Behera, Lambodar

2018-05-02

Brown plant hopper (BPH) is one of the major destructive insect pests of rice, causing severe yield loss. Thirty-two BPH resistance genes have been identified in cultivated and wild species of rice Although, molecular mechanism of rice plant resistance against BPH studied through map-based cloning, due to non-existence of NMR/crystal structures of Bph14 protein, recognition of leucine-rich repeat (LRR) domain and its interaction with different ligands are poorly understood. Thus, in the present study, in silico approach was adopted to predict three-dimensional structure of LRR domain of Bph14 using comparative modelling approach followed by interaction study with jasmonic and salicylic acids. LRR domain along with LRR-jasmonic and salicylic acid complexes were subjected to dynamic simulation using GROMACS, individually, for energy minimisation and refinement of the structure. Final binding energy of jasmonic and salicylic acid with LRR domain was calculated using MM/PBSA. Free-energy landscape analysis revealed that overall stability of LRR domain of Bph14 is not much affected after forming complex with jasmonic and salicylic acid. MM/PBSA analysis revealed that binding affinities of LRR domain towards salicylic acid is higher as compared to jasmonic acid. Interaction study of LRR domain with salicylic acid and jasmonic acid reveals that THR987 of LRR form hydrogen bond with both complexes. Thus, THR987 plays active role in the Bph14 and phytochemical interaction for inducing resistance in rice plant against BPH. In future, Bph14 gene and phytochemicals could be used in BPH management and development of novel resistant varieties for increasing rice yield.

Project Genesis: Mars in situ propellant technology demonstrator mission

NASA Technical Reports Server (NTRS)

Acosta, Francisco Garcia; Anderson, Scott; Andrews, Jason; Deger, Matt; Hedman, Matt; Kipp, Jared; Kobayashi, Takahisa; Marcelo, Mohrli; Mark, Karen; Matheson, Mark

1994-01-01

Project Genesis is a low cost, near-term, unmanned Mars mission, whose primary purpose is to demonstrate in situ resource utilization (ISRU) technology. The essence of the mission is to use indigenously produced fuel and oxidizer to propel a ballistic hopper. The Mars Landing Vehicle/Hopper (MLVH) has an Earth launch mass of 625 kg and is launched aboard a Delta 117925 launch vehicle into a conjunction class transfer orbit to Mars. Upon reaching its target, the vehicle performs an aerocapture maneuver and enters an elliptical orbit about Mars. Equipped with a ground penetrating radar, the MLVH searches for subsurface water ice deposits while in orbit for several weeks. A deorbit burn is then performed to bring the MLVH into the Martian atmosphere for landing. Following aerobraking and parachute deployment, the vehicle retrofires to a soft landing on Mars. Once on the surface, the MLVH begins to acquire scientific data and to manufacture methane and oxygen via the Sabatier process. This results in a fuel-rich O2/CH4 mass ratio of 2, which yields a sufficiently high specific impulse (335 sec) that no additional oxygen need be manufactured, thus greatly simplifying the design of the propellant production plant. During a period of 153 days the MLVH produces and stores enough fuel and oxidizer to make a 30 km ballistic hop to a different site of scientific interest. At this new location the MLVH resumes collecting surface and atmospheric data with the onboard instrumentation. Thus, the MLVH is able to provide a wealth of scientific data which would otherwise require two separate missions or separate vehicles, while proving a new and valuable technology that will facilitate future unmanned and manned exploration of Mars. Total mission cost, including the Delta launch vehicle, is estimated to be $200 million.

Apparatus and method for harvesting woody plantations

DOEpatents

Eggen, David L.

1988-11-15

A tree harvester for harvesting felled trees includes a wheel mounted wood chipper which moves toward the butt ends of the tree stems to be processed. The harvester includes a plurality of rotating alignment discs in front of the chipper. These discs align the tree stems to be processed with the mouth of the chipper. A chipper infeed cylinder is rotatably mounted between the discs and the front end of the chipper, and lifts the tree stem butts up from the ground into alignment with the chipper inlet port. The chips discharge from the chipper and go into a chip hopper which moves with the tree harvester.

Apparatus and method for harvesting woody plantations

DOEpatents

Eggen, D.L.

1988-11-15

A tree harvester for harvesting felled trees includes a wheel mounted wood chipper which moves toward the butt ends of the tree stems to be processed. The harvester includes a plurality of rotating alignment discs in front of the chipper. These discs align the tree stems to be processed with the mouth of the chipper. A chipper infeed cylinder is rotatably mounted between the discs and the front end of the chipper, and lifts the tree stem butts up from the ground into alignment with the chipper inlet port. The chips discharge from the chipper and go into a chip hopper which moves with the tree harvester. 8 figs.

APPARATUS FOR HANDLING MIXTURES OF SOLID MATERIALS

DOEpatents

Hubbell, J.P.

1959-08-25

An apparatus is described for handling either a mixture of finely subdivided materials or a single material requiring a compacting action thereon preparatory to a chemical reducing process carried out in a crucible container. The apparatus is designed to deposit a mixture of dust-forming solid materials in a container while confining the materials against escape into the surrounding atmosphere. A movable filling tube, having a compacting member, is connected to the container and to a covered hopper receiving the mixture of materials. The filling tube is capable of reciprocating in the container and their relative positions are dependent upon the pressure established upon the material by the compacting member.

28. VIEW OF BOILER 901 (IS IT 900?) AT GROUND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

28. VIEW OF BOILER 901 (IS IT 900?) AT GROUND LEVEL. INSTALLED IN 1928 IT WAS FIRED WITH PULVERIZED COAL. THE PULVERIZERS ARE LOCATED TO THE LEFT AND RIGHT OF THE CENTER ASH PIT ACCESS, BELOW THE CIRCULAR AIR INTAKES. THE PULVERIZED ON THE LEFT WAS POWERED WITH AN ELECTRIC MOTOR WHILE THE UNIT ON THE RIGHT WAS DRIVEN BY A STEAM TURBINE. THE HOPPER (TOP CENTER) WAS FILLED VIA A LARRY CAR WHICH RODE ON TRACKS SUSPENDED ABOVE THE FIRING AISLE. THIS BOILER WAS SHUT DOWN IN 1957. - New York, New Haven & Hartford Railroad, Cos Cob Power Plant, Sound Shore Drive, Greenwich, Fairfield County, CT

The lunar hopping transporter

NASA Technical Reports Server (NTRS)

Degner, R.; Kaplan, M. H.; Manning, J.; Meetin, R.; Pasternack, S.; Peterson, S.; Seifert, H.

1971-01-01

Research on several aspects of lunar transport using the hopping mode is reported. Hopping exploits the weak lunar gravity, permits fuel economy because of partial recompression of propellant gas on landing, and does not require a continuous smooth surface for operation. Three questions critical to the design of a lunar hopping vehicle are addressed directly in this report: (1) the tolerance of a human pilot for repeated accelerations; (2) means for controlling vehicle attitude during ballistic flight; and (3) means of propulsion. In addition, a small scale terrestrial demonstrator built to confirm feasibility of the proposed operational mode is described, along with results of preliminary study of unmanned hoppers for moon exploration.

An Influenced Future

NASA Technical Reports Server (NTRS)

Owens, Christopher

2016-01-01

Phobos is a vital precursor and catalyst before our next giant leap to Mars. The principle period of a Phobos' mission could be a series of robotic precursor missions for experimental perception, soil examination, ecological approval and landing site distinguishing proof. For my summer intern position at Johnson Space Center I chipped away at creating a GUNNS (General Use Nodal Network Solver) based power subsystem model for the miniATHLETE hopper, which is a conceptual (idea-based) robotic lander that will operate on Phobos. Keeping in mind the end goal to begin on my venture, I needed to comprehend my undertaking before whatever else, in which I concentrated on C++ to see how to implement the code that GUNNS generates to a Trick S_define file. Prior to coming to this internship at Johnson Space Center Dr. Edwin Zack Crues provided a class on modeling and simulation, which introduced me to the Trick simulation environment. The goal of my project was to develop a GUNNS based power subsystem model for the miniATHLETE hopper. The model needed to incorporate a solar array, battery, hopping legs, and onboard scientific instruments (sensitive measuring/recording devices). The secondary bonus goal after I completed the electrical aspect of my model was to develop a GUNNS based thermal subsystem model for the miniATHLETE hopper. Stringing the two aspects together, I would need to code up a signal aspect to make the system work as one. Accomplishing my goals would not be an easy thing, however I had successfully completed the electrical aspect model with twenty-four servos, six cameras, and multiple sensors. Venturing to complete my project has eluded me to many failures in my design to tune many things like the battery to the proper voltage and the load to the proper wattage. During this time I had touched up on advanced topics in calculus in which I implemented in the converter in my electrical model. I am currently working with my mentor Zu Qun Li to create a signal aspect to control the temperatures inside my electrical aspect model. During my time at JSC I had effectively figured out how to create subsystem models utilizing Trick and GUNNS. I obtain essential knowledge of power and thermal subsystem design for a robotic vehicle. I also learned how to work and communicate in a team effectively to accomplish a goal. Before coming to Johnson Space Center my future career and educational goals included uncertainty, however now I have a completely new look on my path to a prosperous future. My NASA experience has unquestionably impacted me to accomplish and surpass my own particular desires. After my time at Johnson Space Center I plan to apply for a coop position for NASA. This has been a dream come true that I adored each moment being at JSC realizing that I am far fit for doing things most individuals can just long for.

The Hopper: A Wearable Robotic Device Testbed for Micro-Gravity Bone-Loading Proof-of-Concept

NASA Technical Reports Server (NTRS)

Beck, C. E.; Rovekamp, R. N.; Neuhaus, P. D.

2015-01-01

Wearable robotic systems are showing increased potential for addressing crew countermeasures needs. Wearable robots offer a compactness, programmability, and eccentric loading capability not present in more conventional exercise equipment. Correspondingly, advancements in the man to machine interface has progressed, allowing for higher loads to be applied directly to the person in new and novel ways. Recently, the X1 exoskeleton, a lower extremity wearable robot originally designed for mobility assistance and rehabilitation, underwent human subject testing to assess its potential as a knee dynamometer. This was of interest to NASA physiologists because currently strength is not assessed in flight due to hardware limitations, and thus there is a poor understanding of the time course of in-flight changes to muscle strength. The study concluded that the X1 compared well with the Biodex, the "gold standard" in terrestrial dynamometry, with coefficients of variation less than 6.0%. In a following study, the X1 powered ankle was evaluated for its efficacy in exercising calf muscles. Current on-orbit countermeasures equipment does not adequately protect the calf from atrophy. The results of this study were also positive (targeted muscle activity demonstrated via comparing pre- and post-exercise magnetic resonance imaging T2 measurements), again showing the efficacy of wearable robotic devices for addressing the countermeasure needs of our astronauts. Based on these successes and lessons learned, the Grasshopper was co-developed between IHMC (Florida Institute for Human and Machine Cognition) and NASA. The Grasshopper, or the Hopper for short, is a wearable robotic device designed to address muscle and bone density loss for astronauts spending extended periods of time in micro-gravity. The Grasshopper connects to the user's torso like a hiking backpack, over the shoulders and around the waist. At the feet are footplates that strap to the user. There are two actuators, one at each "knee" joint, which are capable of high fidelity torque control. Because the Hopper uses motors instead of gravity to create the load on the user, the device is suited for use on space missions. Exercise in zero-gravity conditions is critical to maintain muscle strength and bone mass. In operation, the actuators try to fold up, or collapse, the device, putting a compressive load between the user's feet and torso. This force is similar to carrying a heavy backpack. The user then bends and extends his or her knees, replicating a weightlifting squat exercise. The applied load is precisely controlled by a computer, and can be programmed to simulate gravitation loads or any desired load prescription, such as free-weight squat exercise. It is even possible to perform eccentric exercises, or negatives, without the need for a spotter. Because the hip joints, as well as the spine and long leg bones, are in the applied load path, there is the potential to stimulate bone growth, countering the typical bone loss when astronauts return from extended duration space travel.

Mesoionic Pyrido[1,2-a]pyrimidinone Insecticides: From Discovery to Triflumezopyrim and Dicloromezotiaz.

PubMed

Zhang, Wenming

2017-09-19

One of the greatest global challenges is to feed the ever-increasing world population. The agrochemical tools growers currently utilize are also under continuous pressure, due to a number of factors that contribute to the loss of existing products. Mesoionic pyrido[1,2-a]pyrimidinones are an unusual yet very intriguing class of compounds. Known for several decades, this class of compounds had not been systemically studied until we started our insecticide discovery program. This Account provides an overview of the efforts on mesoionic pyrido[1,2-a]pyridinone insecticide discovery, beginning from the initial high throughput screen (HTS) discovery to ultimate identification of triflumezopyrim (4, DuPont Pyraxalt) and dicloromezotiaz (5) for commercialization as novel insecticides. Mesoionic pyrido[1,2-a]pyrimidinones with a n-propyl group at the 1-position, such as compound 1, were initially isolated as undesired byproducts from reactions for a fungicide discovery program at DuPont Crop Protection. Such compounds showed interesting insecticidal activity in a follow-up screen and against an expanded insect species list. The area became an insecticide hit for exploration and then a lead area for optimization. At the lead optimization stage, variations at three regions of compound 1, i.e., side-chain (n-propyl group), substituents on the 3-phenyl group, and substitutions on the pyrido- moiety, were explored with many analogues prepared and evaluated. Breakthrough discoveries included replacing the n-propyl group with a 2,2,2-trifluoroethyl group to generate compound 2, and then with a 2-chlorothiazol-5-ylmethyl group to form compound 3. 3 possesses potent insecticidal activity not only against a group of hopper species, including corn planthopper (Peregrinus maidis (Ashmead), CPH) and potato leafhopper (Empoasca fabae (Harris), PLH), as well as two key rice hopper species, namely, brown planthopper (Nilaparvata lugens (Stål), BPH) and rice green leafhopper (Nephotettix virescens (Distant), GLH), but also against representative lepidoptera species Diamondback moth (Plutella xylostella (Linnaeus), DBM) and fall armyworm (Spodoptera frugiperda (J.E. Smith), FAW). Further optimization based on 3 led to discovery of triflumezopyrim (4), with a 5-pyrimidinylmethyl group, as a potent hopper insecticide for rice usage. Optimization of the substituents on the pyrido- moiety of 3 resulted in discovery of dicloromezotiaz (5) as a lepidoptera insecticide. In this Account, we present the discovery and optimization of mesoionic pyrido[1,2-a]pyrimidinone insecticides toward the identification of triflumezopyrim (4) and dicloromezotiaz (5). We hope that knowledge and lessons derived from this discovery program will provide valuable information for future agrochemical and drug discovery. Our successful discovery and commercialization development of two novel insecticides based on meosoionic pyrido[1,2-a]pyridiminones may also stimulate interests of scientists from other disciplines to adopt this uncommon yet intriguing heterocycle ring system in pharmaceutical and other material science discovery research.

11. PUMP HOUSE AND WEIGHING ROOM Fish were pumped from ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. PUMP HOUSE AND WEIGHING ROOM Fish were pumped from floating hoppers, to the pump house (on the far right). From there they were either lifted by conveyor belt to the weighing room (top center) and thence to the holding tanks, or were washed through sealers, weighed and then sluiced to holding tanks. The process used depended upon the type and size of fish. The square cement vat (center) was to be a settling tank from which fish oil, reclaimed from the reduction process, was to be pumped into the round metal tank (above the vat). This process however, was never fully utilized before the sardines ran out. - Hovden Cannery, 886 Cannery Row, Monterey, Monterey County, CA

Hierarchical Hopping through Localized States in a Random Potential

NASA Astrophysics Data System (ADS)

Rajan, Harihar; Srivastava, Vipin

2003-03-01

Generalisation of Mott's idea on (low - temperature, large-time), Variable-range-hopping is considered to include hopping at some what higher temperature(that do not kill localization). These transitions complement the variable- range-hopping in that they do not conserve energy and occur at relatively lower time scales. The hopper picks the next state in a hierarchical fashion in accordance with certain conditions. The results are found to tie up nicely with an interesting property pertaining to the energy dependence of localized states. Acknowlwdgements: One of us(VS) would like to thank Association of Commonwealth Universities and Leverhulme Trust for financial help and to Sir Sam Edwards for hospitality at Cavendish Laboratory,Cambridge CB3 0HE.

In vitro effect of fenthion on human lymphocytes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rani, M.V.U.; Rao, M.S.

1991-08-01

Fenthion is an organophosphorus insecticide which is extensively used in control of leaf hoppers, cutworms, mites on vegetable crops. It has been reported that organophosphorus pesticides cause a significant increase in sister chromatid exchanges in mammalian cell lines. A significant increase of chromosomal aberrations has been reported in rural population exposed to pesticides. Organosphosphorus pesticides malathion, diazinon, dimethoate, phosdrin and dursban induced sister chromatid exchanges in human lymphoid cells. Exchange type of aberration has been reported in fluoriculturist who were exposed to organophosphorus, organochlorine pesticides. In the present investigation an attempt has been made to evaluate the cytogenetic effect ofmore » fenthion in human lymphocyte cultures in vitro.« less

Granular flows: fundamentals and applications

NASA Astrophysics Data System (ADS)

Cleary, Paul W.

DEM allows the prediction of complex industrial and geophysical particle flows. The importance of particle shape is demonstrated through a series of simple examples. Shape controls resistance to shear, the magnitude of collision stress, dilation and the angle of repose. We use a periodic flow of a bed of particles to demonstrate the different states of granular matter, the generation of dilute granular flow when granular temperature is high and the flow dependent nature of the granular thermodynamic boundary conditions. A series of industrial case studies examines how DEM can be used to understand and improve processes such as separation, mixing, grinding, excavation, hopper discharge, metering and conveyor interchange. Finally, an example of landslide motion over real topography is presented.

Spontaneous density fluctuations in granular flow and traffic

NASA Astrophysics Data System (ADS)

Herrmann, Hans J.

It is known that spontaneous density waves appear in granular material flowing through pipes or hoppers. A similar phenomenon is known from traffic jams on highways. Using numerical simulations we show that several types of waves exist and find that the density fluctuations follow a power law spectrum. We also investigate one-dimensional traffic models. If positions and velocities are continuous variables the model shows self-organized criticality driven by the slowest car. Lattice gas and lattice Boltzmann models reproduce the experimentally observed effects. Density waves are spontaneously generated when the viscosity has a non-linear dependence on density or shear rate as it is the case in traffic or granular flow.

USA's Black Thunder mine: a truck and shovel operation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dorling, I.

During 1966/1967, ARCO obtained over 2,631 hectares (6,500 acres) of federal and state coal leases, and initial exploration was started. A total of 312 coal core holes were drilled and logged to determine the reserves and quality of the coal. The results indicated that a large surface mine could be developed to exploit the substantial reserves. The application procedure for permits was started early in 1974. Thunder Basin Coal Company is mining the Wyodak-Anderson Seam where the coal is about 21 meters (69 feet) thick. It has been estimated that a total of 750,000,000 tons of coal exist with amore » 0.3 to 0.4 percent sulfur content and a heating value of about 8,600 Btu per pound. The seam is mined in one lift using electric shovels and trucks. There are many factors which govern the choice of either a dragline or a truck and shovel operation for removing overburden. At the Black Thunder mine the conditions which favored the choice of the truck and shovel method were topography and pit geometry. The run-of-mine coal is dumped into two 540-ton hoppers. Underground vibrating grizzly feeders (2,500 tph capacity) pass the coal into 2,500 tph primary single-roll crushers, where the ROM coal is reduced to minus 8 inches. A 72-inch-wide elevating conveyor carries the coal to a 110-ton surge hopper, and is then fed into two secondary crushers where the coal is further reduced to minus-2 inches. The system is able to handle 5,000 tons of ROM coal per hour. The total production of coal from the mine in 1978 is expected to be about 3,000,000 tons, depending on customer requirements. It is expected that in 1979 the output will rise to 8,000,000 tons, and by 1983 the full planned production of 20,000,000 tons a year will be reached. (LTN)« less

From "They" Science to "Our" Science: Hip Hop Epistemology in STEAM Education

NASA Astrophysics Data System (ADS)

Dolberry, Maurice E.

Hip hop has moved from being considered a type of music into being understood as a culture in which a prominent type of music originates. Hip hop culture has a philosophy and epistemological constructs as well. This study analyzed those constructs to determine how conceptions of science factor in hip hop worldviews. Pedagogical models in culturally responsive teaching and Science, Technology, Engineering, Arts, and Mathematics (STEAM) education were also examined to discern their philosophical connections with hip hop culture. These connections were used to create two theoretical models. The first one, Hip Hop Science, described how scientific thought functions in hip hop culture. The second model, Hip Hop STEAM Pedagogy, proposes how hip hop culture can inform STEAM teaching practices. The study began by using Critical Race Theory to create a theoretical framework proposing how the two theoretical models could be derived from the philosophical and pedagogical concepts. Content analysis and narrative inquiry were used to analyze data collected from scholarly texts, hip hop songs, and interviews with hip hop-responsive educators. The data from these sources were used initially to assess the adequacy of the proposed theoretical framework, and subsequently to improve its viability. Four overlapping themes emerged from the data analyses, including hip hop-resistance to formal education; how hip hop culture informs pedagogical practice in hip hop-responsive classrooms; conceptions of knowledge and reality that shape how hip hoppers conduct scientific inquiry; and hip hop-based philosophies of effective teaching for hip hoppers as a marginalized cultural group. The findings indicate that there are unique connections between hip hop epistemology, sciencemindedness, and pedagogical practices in STEAM education. The revised theoretical framework clarified the nature of these connections, and supported claims from prior research that hip hop culture provides viable sites of engagement for STEAM educators. It concluded with suggestions for future research that further explicates hip hop epistemology and Hip Hop STEAM Pedagogy.

The high aerobic capacity of a small, marsupial rat-kangaroo (Bettongia penicillata) is matched by the mitochondrial and capillary morphology of its skeletal muscles.

PubMed

Webster, Koa N; Dawson, Terence J

2012-09-15

We examined the structure-function relationships that underlie the aerobic capacities of marsupial mammals that hop. Marsupials have relatively low basal metabolic rates (BMR) and historically were seen as 'low energy' mammals. However, the red kangaroo, Macropus rufus (family Macropodidae), has aerobic capacities equivalent to athletic placentals. It has an extreme aerobic scope (fAS) and its large locomotor muscles feature high mitochondrial and capillary volumes. M. rufus belongs to a modern group of kangaroos and its high fAS is not general for marsupials. However, other hopping marsupials may have elevated aerobic capacities. Bettongia penicillata, a rat-kangaroo (family Potoroidae), is a small (1 kg), active hopper whose fAS is somewhat elevated. We examined the oxygen delivery system in its muscles to ascertain links with hopping. An elevated fAS of 23 provided a relatively high maximal aerobic oxygen consumption ( ) in B. penicillata; associated with this is a skeletal muscle mass of 44% of body mass. Ten muscles were sampled to estimate the total mitochondrial and capillary volume of the locomotor muscles. Values in B. penicillata were similar to those in M. rufus and in athletic placentals. This small hopper had high muscle mitochondrial volume densities (7.1-11.9%) and both a large total capillary volume (6 ml kg(-1) body mass) and total capillary erythrocyte volume (3.2 ml kg(-1)). Apparently, a considerable aerobic capacity is required to achieve the benefits of the extended stride in fast hopping. Of note, the ratio of to total muscle mitochondrial volume in B. penicillata was 4.9 ml O(2) min(-1) ml(-1). Similar values occur in M. rufus and also placental mammals generally, not only athletic species. If such relationships occur in other marsupials, a fundamental structure-function relationship for oxygen delivery to muscles likely originated with or before the earliest mammals.

High pressure rotary piston coal feeder for coal gasification applications

DOEpatents

Gencsoy, Hasan T.

1977-05-24

The subject development is directed to an apparatus for feeding pulverized coal into a coal gasifier operating at relatively high pressures and elevated temperatures. This apparatus is a rotary piston feeder which comprises a circular casing having a coal loading opening therein diametrically opposed from a coal discharge and contains a rotatable discoid rotor having a cylinder in which a reciprocateable piston is disposed. The reciprocation of the piston within the cylinder is provided by a stationary conjugate cam arrangement whereby the pulverized coal from a coal hopper at atmospheric pressure can be introduced into the cylinder cavity and then discharged therefrom into the high-pressure gasifier without the loss of high pressure gases from within the latter.

Glycosides of the Neurotoxin Tutin in Toxic Honeys Are from Coriaria arborea Phloem Sap, Not Insect Metabolism.

PubMed

Watkins, Oliver C; Joyce, Nigel I; Gould, Nick; Perry, Nigel B

2018-04-27

Some honeys contain the neurotoxin tutin (1) plus hyenanchin (2), 2-(β-d-glucopyranosyl)tutin (3), and 2-[6'-(α-d-glucopyranosyl)-β-d-glucopyranosyl]tutin (4). These honeys are made by bees collecting honeydew from passionvine hoppers feeding on the sap of tutu plants ( Coriaria spp.). We report a LC-MS study showing that all these picrotoxanes are of plant, not insect, origin. Hyenanchin was barely detectable and the diglucoside was not detectable in C. arborea leaves, but tutu phloem sap contained all four compounds at concentrations up to the highest found in honeydew. It is proposed that the diglucoside may function as a transport form of tutin, analogous to sucrose transport in phloem.

Simulation study of the discharge characteristics of silos with cohesive particles

NASA Astrophysics Data System (ADS)

Hund, David; Weis, Dominik; Hesse, Robert; Antonyuk, Sergiy

2017-06-01

In many industrial applications the silo for bulk materials is an important part of an overall process. Silos are used for instance to buffer intermediate products to ensure a continuous supply for the next process step. This study deals with the discharging behaviour of silos containing cohesive bulk solids with particle sizes in the range of 100-500 μm. In this contribution the TOMAS [1,2] model developed for stationary and non-stationary discharging of a convergent hopper is verified with experiments and simulations using the Discrete Element Method. Moreover the influence of the cohesion of the bulk solids on the discharge behaviour is analysed by the simulation. The simulation results showed a qualitative agreement with the analytical model of TOMAS.

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

In 1973, 590 million tons of coal were produced. In order to increase the 1974 production to 660 million tons, the following criteria must be attained: labor stability with an end to absenteeism and wildcat stoppages; effective enforcement of mine health and safe ty laws without harassment or unnecessary mine closures; continue surface mining with reasonable reclamation requirements; adequate rail hopper cars; exemption from price controls of all coal sales; variances in air pollution control regulations to allow burning of available high- sulfur coals; and adequate mine supplies, especially roof bolts, fuels, and explosives. Suitable sites have been selected formore » coal gasification plants. SNG from coal is expected to be competitive with gas brought by pipeline from Alaska, gas imported as a liquid in cryogenic tankers, and SNG produced from naphtha or other feedstocks. (MCW)« less

Magnesium and Carbon Dioxide - A Rocket Propellant for Mars Missions

NASA Technical Reports Server (NTRS)

Shafirovich, E. IA.; Shiriaev, A. A.; Goldshleger, U. I.

1993-01-01

A rocket engine for Mars missions is proposed that could utilize CO2 accumulated from the Martian atmosphere as an oxidizer. For use as possible fuel, various metals, their hydrides, and mixtures with hydrogen compounds are considered. Thermodynamic calculations show that beryllium fuels ensure the most impulse but poor inflammability of Be and high toxicity of its compounds put obstacles to their applications. Analysis of the engine performance for other metals together with the parameters of ignition and combustion show that magnesium seems to be the most promising fuel. Ballistic estimates imply that a hopper with the chemical rocket engine on Mg + CO2 propellant could be readily developed. This vehicle would be able to carry out 2-3 ballistic flights on Mars before the final ascent to orbit.

Two years at Meridiani Planum: Results from the opportunity rover

USGS Publications Warehouse

Squyres, S. W.; Knoll, A.H.; Arvidson, R. E.; Clark, B. C.; Grotzinger, J.P.; Jolliff, B.L.; McLennan, S.M.; Tosca, N.; Bell, J.F.; Calvin, W.M.; Farrand, W. H.; Glotch, T.D.; Golombek, M.P.; Herkenhoff, K. E.; Johnson, J. R.; Klingelhofer, G.; McSween, H.Y.; Yen, A. S.

2006-01-01

The Mars Exploration Rover Opportunity has spent more than 2 years exploring Meridiani Planum, traveling ???8 kilometers and detecting features that reveal ancient environmental conditions. These include well-developed festoon (trough) cross-lamination formed in flowing liquid water, strata with smaller and more abundant hematite-rich concretions than those seen previously, possible relict "hopper crystals" that might reflect the formation of halite, thick weathering rinds on rock surfaces, resistant fracture fills, and networks of polygonal fractures likely caused by dehydration of sulfate salts. Chemical variations with depth show that the siliciclastic fraction of outcrop rock has undergone substantial chemical alteration from a precursor basaltic composition. Observations from microscopic to orbital scales indicate that ancient Meridiani once had abundant acidic groundwater, arid and oxidizing surface conditions, and occasional liquid flow on the surface.

Environmental effects of dredging: Alternative dredging equipment and operational methods to minimize sea turtle mortalities. Technical notes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dickerson, D.D.; Nelson, D.A.

1990-12-01

Five species of sea turtles occur along the United States coastlines and are listed as threatened or endangered. The loggerhead sea turtle (Caretta caretta) is listed as threatened, while the Kemp`s ridley (Lepidochelys kenipi), the hawksbill (Eretmochelys imbricata), and the leatherback (Dermochelys coriacea) are all less abundant and listed as endangered. Florida breeding populations of the green sea turtle (Chelonia mydas) are listed as endangered, but green turtles in other US waters are considered threatened. The National Marine Fisheries Service (NMFS) has determined, based on the best available information, that because of their life cycle and behavioral patterns only themore » loggerhead, the green, and the Kemp`s ridley are put at risk by hopper dredging activities (Studt 1987).« less

Multiple feed powder splitter

DOEpatents

Lewis, Gary K.; Less, Richard M.

2001-01-01

A device for providing uniform powder flow to the nozzles when creating solid structures using a solid fabrication system such as the directed light fabrication (DLF) process. In the DLF process, gas entrained powders are passed through the focal point of a moving high-power laser light which fuses the particles in the powder to a surface being built up in layers. The invention is a device providing uniform flow of gas entrained powders to the nozzles of the DLF system. The device comprises a series of modular splitters which are slidably interconnected and contain an integral flow control mechanism. The device can take the gas entrained powder from between one to four hoppers and split the flow into eight tubular lines which feed the powder delivery nozzles of the DLF system.

Multiple feed powder splitter

DOEpatents

Lewis, Gary K.; Less, Richard M.

2002-01-01

A device for providing uniform powder flow to the nozzles when creating solid structures using a solid fabrication system such as the directed light fabrication (DLF) process. In the DLF process, gas entrained powders are passed through the focal point of a moving high-power laser light which fuses the particles in the powder to a surface being built up in layers. The invention is a device providing uniform flow of gas entrained powders to the nozzles of the DLF system. The device comprises a series of modular splitters which are slidably interconnected and contain an integral flow control mechanism. The device can take the gas entrained powder from between one to four hoppers and split the flow into eight tubular lines which feed the powder delivery nozzles of the DLF system.

Component and System Sensitivity Considerations for Design of a Lunar ISRU Oxygen Production Plant

NASA Technical Reports Server (NTRS)

Linne, Diane L.; Gokoglu, Suleyman; Hegde, Uday G.; Balasubramaniam, Ramaswamy; Santiago-Maldonado, Edgardo

2009-01-01

Component and system sensitivities of some design parameters of ISRU system components are analyzed. The differences between terrestrial and lunar excavation are discussed, and a qualitative comparison of large and small excavators is started. The effect of excavator size on the size of the ISRU plant's regolith hoppers is presented. Optimum operating conditions of both hydrogen and carbothermal reduction reactors are explored using recently developed analytical models. Design parameters such as batch size, conversion fraction, and maximum particle size are considered for a hydrogen reduction reactor while batch size, conversion fraction, number of melt zones, and methane flow rate are considered for a carbothermal reduction reactor. For both reactor types the effect of reactor operation on system energy and regolith delivery requirements is presented.

Granular Materials and the Risks They Pose for Success on the Moon and Mars

NASA Technical Reports Server (NTRS)

Wilkinson, R. Allen; Behringer, Robert P.; Jenkins, James T.; Louge, Michel Y.

2004-01-01

Working with soil, sand, powders, ores, cement and sintered bricks, excavating, grading construction sites, driving off-road, transporting granules in chutes and pipes, sifting gravel, separating solids from gases, and using hoppers are so routine that it seems straightforward to do it on the Moon and Mars as we do it on Earth. This paper brings to the fore how little these processes are understood and the millennia-long trial-and-error practices that lead to today's massive over-design, high failure rate, and extensive incremental scaling up of industrial processes because of the inadequate predictive tools for design. We present a number of pragmatic scenarios where granular materials play a role, the risks involved, and what understanding is needed to greatly reduce the risks.

Granular Materials and the Risks They Pose for Success on the Moon and Mars

NASA Astrophysics Data System (ADS)

Wilkinson, R. Allen; Behringer, Robert P.; Jenkins, James T.; Louge, Michel Y.

2005-02-01

Working with soil, sand, powders, ores, cement and sintered bricks, excavating, grading construction sites, driving off-road, transporting granules in chutes and pipes, sifting gravel, separating solids from gases, and using hoppers are so routine that it seems straightforward to do it on the Moon and Mars as we do it on Earth. This paper brings to the fore how little these processes are understood and the millennia-long trial-and-error practices that lead to today's massive over-design, high failure rate, and extensive incremental scaling up of industrial processes because of the inadequate predictive tools for design. We present a number of pragmatic scenarios where granular materials play a role, the risks involved, and what understanding is needed to greatly reduce the risks.

Speciation of Cr and its leachability in coal by-products from spanish coal combustion plants.

PubMed

López-Antón, M Antonia; Díaz-Somoano, Mercedes; Cuesta, Aida Fuente; Riesco, Aida Rubio; Martínez-Tarazona, M Rosa

2008-06-01

This study evaluates the behaviour of total Cr and Cr (VI) during coal combustion in two Spanish power stations. The content and distribution of Cr in the feed coal and combustion wastes was determined and the Cr contents were normalized using enrichment factor indexes. The speciation of Cr in the fly ash fractions from the different hoppers of the electrostatic precipitators was established and the possibility that the Cr (VI) might lixiviate when ashes are disposed of at landfill sites was assessed. Differences in the distribution and behavior of Cr in the two power stations were observed. According to European directive 1999/31/CEE, soluble Cr(VI) in the fly ashes studied would be unlikely to pose an environmental or health risk when the ash is disposed of.

A Flow-Channel Analysis for the Mars Hopper

DOE Office of Scientific and Technical Information (OSTI.GOV)

W. Spencer Cooley

The Mars Hopper is an exploratory vehicle designed to fly on Mars using carbon dioxide from the Martian atmosphere as a rocket propellant. The propellent gasses are thermally heated while traversing a radioisotope ther- mal rocket (RTR) engine’s core. This core is comprised of a radioisotope surrounded by a heat capacitive material interspersed with tubes for the propellant to travel through. These tubes, or flow channels, can be manu- factured in various cross-sectional shapes such as a special four-point star or the traditional circle. Analytical heat transfer and computational fluid dynamics (CFD) anal- yses were performed using flow channels withmore » either a circle or a star cross- sectional shape. The nominal total inlet pressure was specified at 2,805,000 Pa; and the outlet pressure was set to 2,785,000 Pa. The CO2 inlet tem- perature was 300 K; and the channel wall was 1200 K. The steady-state CFD simulations computed the smooth-walled star shape’s outlet temper- ature to be 959 K on the finest mesh. The smooth-walled circle’s outlet temperature was 902 K. A circle with a surface roughness specification at 0.01 mm gave 946 K and at 0.1 mm yielded 989 K. The The effects of a slightly varied inlet pressure were also examined. The analytical calculations were based on the mass flow rates computed in the CFD simulations and provided significantly higher outlet temperature results while displaying the same comparison trends. Research relating to the flow channel heat transfer studies was also done. Mathematical methods to geometrically match the cross-sectional areas of the circle and star, along with a square and equilateral triangle, were derived. A Wolfram Mathematica 8 module was programmed to analyze CFD results using Richardson Extrapolation and calculate the grid convergence index (GCI). A Mathematica notebook, also composed, computes and graphs the bulk mean temperature along a flow channel’s length while the user dynam- ically provides the input variables, allowing their effects on the temperature to be more easily observed.« less

Computer Simulation of the Hydrodynamic Processes of Cyclone Dust Collectors

NASA Astrophysics Data System (ADS)

Plashikhin, S. V.

2016-09-01

In the present paper, the gas-dynamic flow structures in dust collectors with an internal louvered element and an external dust hopper and the traditional design of the NIIOGAZ type have been considered. The character of motion of particles of various median diameters in a cyclone dust collector has also been investigated. A survey has been made of the literature of foreign and home authors dealing with questions of filtration of solid particles in the gas flow in apparatuses of the centrifugal type [1, 2]. The arrangement and principle of operation of the cyclone dust collector is presented. The computational modeling of the flow was carried out by solving Reynolds-averaged Navier-Stokes (RANS) equations by the CFD method with the use of a k-ɛ turbulence model for four modes of operation of the apparatus.

Lunar base and Mars base design projects

NASA Technical Reports Server (NTRS)

Amos, J.; Campbell, J.; Hudson, C.; Kenny, E.; Markward, D.; Pham, C.; Wolf, C.

1989-01-01

The space design classes at the University of Texas at Austin undertook seven projects in support of the NASA/USRA advanced space design program during the 1988-89 year. A total of 51 students, including 5 graduate students, participated in the design efforts. Four projects were done within the Aerospace Engineering (ASE) design program and three within the Mechanical Engineering (ME) program. Both lunar base and Mars base design efforts were studied, and the specific projects were as follows: Lunar Crew Emergency Rescue Vehicle (ASE); Mars Logistics Lander Convertible to a Rocket Hopper (ME); A Robotically Constructed Production and Supply Base on Phobos (ASE); A Mars/Phobos Transportation System (ASE); Manned Base Design and Related Construction Issues for Mars/Phobos Mission (ME); and Health Care Needs for a Lunar Colony and Design of Permanent Medical Facility (ME).

Laboratory duplication of comb layering in the Rhum pluton. [igneous rocks with comb layered texture

NASA Technical Reports Server (NTRS)

Donaldson, C. H.

1977-01-01

A description is provided of the texture of harrisite comb layers, taking into account the results of crystallization experiments at controlled cooling rates, which have reproduced the textural change from 'cumulate' to comb-layered harrisite. Melted samples of harrisite were used in the dynamic crystallization experiments considered. The differentiation of a cooling rate run with respect to olivine grain size and shape is shown and three possible origins of hopper olivine in differentiated crystallization runs are considered. It is found that olivine nucleation occurred throughout cooling, except for the incubation period during early cooling. The elongate combed olivines in harrisite apparently grew as the magma locally supercooled to at least 30 C. It is suggested that the branching crystals in most comb layers, including comb-layered harrisite, probably grew along thermal gradients.

Extraction of Volatiles from Regolith or Soil on Mars, the Moon, and Asteroids

NASA Technical Reports Server (NTRS)

Linne, Diane; Kleinhenz, Julie; Trunek, Andrew; Hoffman, Stephen; Collins, Jacob

2017-01-01

NASA's Advanced Exploration Systems ISRU Technology Project is evaluating concepts to extract water from all resource types Near-term objectives: Produce high-fidelity mass, power, and volume estimates for mining and processing systems Identify critical challenges for development focus Begin demonstration of component and subsystem technologies in relevant environment Several processor types: Closed processors either partially or completely sealed during processing Open air processors operates at Mars ambient conditions In-situ processors Extract product directly without excavation of raw resource Design features Elimination of sweep gas reduces dust particles in water condensate Pressure maintained by height of soil in hopper Model developed to evaluate key design parameters Geometry: conveyor diameter, screw diameter, shaft diameter, flight spacing and pitch Operational: screw speed vs. screw length (residence time) Thermal: Heat flux, heat transfer to soil Testing to demonstrate feasibility and performance Agglomeration, clogging Pressure rise forced flow to condenser.

Effects of a german asthma disease management program using sickness fund claims data.

PubMed

Windt, Roland; Glaeske, Gerd

2010-08-01

The purpose of this study was to assess outcomes of a nationwide asthma disease management (DM) program in Germany. A retrospective observational study with propensity-score matching was performed using claims data of sickness funds exclusively. Effects were analyzed on the basis of a match of 317 program participants and nonparticipants with similar propensity score and age. Hospitalization or oral corticosteroid user rates were comparable in both groups, whereas there are significantly more subjects in the DM group with a prescription of an inhaled corticosteroid and fewer with a prescription of a cromolyn/reproterol combination. There are also less "doctor hoppers" in the DM group, defined as subjects with antiasthmatic drug prescriptions of at least three physicians. The results suggest that the impact of a nationwide disease management program for asthma is weak in respect of clinically relevant endpoints, but there are indications that medication in a DM program approximates asthma guidelines more closely.

A Low-Cost, Reliable, High-Throughput System for Rodent Behavioral Phenotyping in a Home Cage Environment

PubMed Central

Parkison, Steven A.; Carlson, Jay D.; Chaudoin, Tammy R.; Hoke, Traci A.; Schenk, A. Katrin; Goulding, Evan H.; Pérez, Lance C.; Bonasera, Stephen J.

2016-01-01

Inexpensive, high-throughput, low maintenance systems for precise temporal and spatial measurement of mouse home cage behavior (including movement, feeding, and drinking) are required to evaluate products from large scale pharmaceutical design and genetic lesion programs. These measurements are also required to interpret results from more focused behavioral assays. We describe the design and validation of a highly-scalable, reliable mouse home cage behavioral monitoring system modeled on a previously described, one-of-a-kind system [1]. Mouse position was determined by solving static equilibrium equations describing the force and torques acting on the system strain gauges; feeding events were detected by a photobeam across the food hopper, and drinking events were detected by a capacitive lick sensor. Validation studies show excellent agreement between mouse position and drinking events measured by the system compared with video-based observation – a gold standard in neuroscience. PMID:23366406

Isosorbide, a green plasticizer for thermoplastic starch that does not retrogradate.

PubMed

Battegazzore, Daniele; Bocchini, Sergio; Nicola, Gabriele; Martini, Eligio; Frache, Alberto

2015-03-30

Isosorbide is a non-toxic biodegradable diol derived from bio-based feedstock. It can be used for preparing thermoplastic starch through a semi-industrial process of extrusion. Isosorbide allows some technological advantages with respect to classical plasticizers: namely, direct mixing with starch, energy savings for the low processing temperature required and lower water uptake. Indeed, maize starch was directly mixed with the solid plasticizer and direct fed in the main hopper of a co-rotating twin screw extruder. Starch plasticization was assessed by X-ray diffraction (XRD) and dynamic-mechanical analysis (DMTA). Oxygen permeability, water uptake and mechanical properties were measured at different relative humidity (R.H.) values. These three properties turned out to be highly depending on the R.H. No retrogradation and changing of the material properties were occurred from XRD and DMTA after 9 months. Copyright © 2014 Elsevier Ltd. All rights reserved.

Research on lunar and planet development and utilization

NASA Astrophysics Data System (ADS)

Iwata, Tsutomu; Etou, Takao; Imai, Ryouichi; Oota, Kazuo; Kaneko, Yutaka; Maeda, Toshihide; Takano, Yutaka

1992-08-01

Status of the study on unmanned and manned lunar missions, unmanned Mars missions, lunar resource development and utilization missions, remote sensing exploration missions, survey and review to elucidate the problems of research and development for lunar resource development and utilization, and the techniques and equipment for lunar and planet exploration are presented. Following items were studied respectively: (1) spacecraft systems for unmanned lunar missions, such as lunar observation satellites, lunar landing vehicles, lunar surface rovers, lunar surface hoppers, and lunar sample retrieval; (2) spacecraft systems for manned lunar missions, such as manned lunar bases, lunar surface operation robots, lunar surface experiment systems, manned lunar take-off and landing vehicles, and lunar freight transportation ships; (3) spacecraft systems for Mars missions, such as Mars satellites, Phobos and Deimos sample retrieval vehicles, Mars landing explorers, Mars rovers, Mars sample retrieval; (4) lunar resource development and utilization; and (5) remote sensing exploration technologies.

Field Testing of a Pneumatic Regolith Feed System During a 2010 ISRU Field Campaign on Mauna Kea, Hawaii

NASA Technical Reports Server (NTRS)

Craft, Jack; Zacny, Kris; Chu, Philip; Wilson, Jack; Santoro, Chris; Carlson, Lee; Maksymuk, Michael; Townsend, Ivan I.; Mueller, Robert P.; Mantovani, James G.

2010-01-01

Lunar In Situ Resource Utilization (ISRU) consists of a number of tasks starting with mining of lunar regolith, followed by the transfer of regolith to an oxygen extraction reactor and finally processing the regolith and storing of extracted oxygen. The transfer of regolith from the regolith hopper at the ground level to an oxygen extraction reactor many feet above the surface could be accomplished in different ways, including using a mechanical auger, bucket ladder system or a pneumatic system. The latter system is commonly used on earth when moving granular materials since it offers high reliability and simplicity of operation. In this paper, we describe a pneumatic regolith feed system, delivering feedstock to a Carbothermal reactor and lessons learned from deploying the system during the 2010 ISRU field campaign on the Mauna Kea, Hawaii.

Suggested nomenclature change and new reference locality for Dequeen Formation, Pike County, Arkansas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ham, T.L.; Landry, R.J.

1983-09-01

The DeQueen Formation of the Trinity Group, Comanchean Cretaceous, crops out in southwestern Arkansas and southeastern Oklahoma. The outcrop, located in the Highland gypsum quarry of Pike County, southwestern Arkansas, is described in detail in this paper and presented as a reference locality. Data from the locality provide the basis for a nomenclature change from the DeQueen Limestone Member to the DeQueen Formation. The formation consists of 64.23% clastic sediments, 24.72% gypsum, and 11.05% limestone. Hopper salt casts, ripple marks, scattered pyrite and marcasite nodules, celestite, and chickenwire gypsum can also be found. The DeQueen Formation is underlain by claysmore » and the Ultima Thule Gravel lentil, while the top is unconformably overlain by Upper Cretaceous Tokio gravels. The general paleoenvironment represents a normally low-energy subtidal environment ranging from brackish to normal to hypersaline waters in a lagoonal setting that shallows upward.« less

Pneumatic Regolith Transfer Systems for In-Situ Resource Utilization

NASA Technical Reports Server (NTRS)

Mueller, Robert P.; Townsend, Ivan I., III; Mantovani, James G.

2010-01-01

One aspect of In-Situ Resource Utilization (lSRU) in a lunar environment is to extract oxygen and other elements from the minerals that make up the lunar regolith. Typical ISRU oxygen production processes include but are not limited to hydrogen reduction, carbothermal and molten oxide electrolysis. All of these processes require the transfer of regolith from a supply hopper into a reactor for chemical reaction processing, and the subsequent extraction of the reacted regolith from the reactor. This paper will discuss recent activities in the NASA ISRU project involved with developing pneumatic conveying methods to achieve lunar regolith simulant transfer under I-g and 1/6-g gravitational environments. Examples will be given of hardware that has been developed and tested by NASA on reduced gravity flights. Lessons learned and details of pneumatic regolith transfer systems will be examined as well as the relative performance in a 1/6th G environment

Experimental proof of faster-is-slower in systems of frictional particles flowing through constrictions.

PubMed

Pastor, José M; Garcimartín, Angel; Gago, Paula A; Peralta, Juan P; Martín-Gómez, César; Ferrer, Luis M; Maza, Diego; Parisi, Daniel R; Pugnaloni, Luis A; Zuriguel, Iker

2015-12-01

The "faster-is-slower" (FIS) effect was first predicted by computer simulations of the egress of pedestrians through a narrow exit [D. Helbing, I. J. Farkas, and T. Vicsek, Nature (London) 407, 487 (2000)]. FIS refers to the finding that, under certain conditions, an excess of the individuals' vigor in the attempt to exit causes a decrease in the flow rate. In general, this effect is identified by the appearance of a minimum when plotting the total evacuation time of a crowd as a function of the pedestrian desired velocity. Here, we experimentally show that the FIS effect indeed occurs in three different systems of discrete particles flowing through a constriction: (a) humans evacuating a room, (b) a herd of sheep entering a barn, and (c) grains flowing out a 2D hopper over a vibrated incline. This finding suggests that FIS is a universal phenomenon for active matter passing through a narrowing.

Analysis of Water Surplus at the Lunar Outpost

NASA Technical Reports Server (NTRS)

Santiago-Maldonado, Edgardo; Bagdigian, Robert M.; George, Patrick J.; Plachta, David W.; Fincannon, Homer J.; Jefferies, Sharon A.; Keyes, Jennifer P.; Reeves, David M.; Shyface, Hilary R.

2010-01-01

This paper evaluates the benefits to the lunar architecture and outpost of having a surplus of water, or a surplus of energy in the form of hydrogen and oxygen, as it has been predicted by Constellation Program's Lunar Surface System analyses. Assumptions and a scenario are presented leading to the water surplus and the revolutionary surface element options for improving the lunar exploration architecture and mission objectives. For example, some of the elements that can benefit from a water surplus are: the power system energy storage can minimize the use of battery systems by replacing batteries with higher energy density fuel cell systems; battery packs on logistics pallets can also be minimized; mobility asset power system mass can be reduced enabling more consumables and extended roving duration and distance; small robotic vehicles (hoppers) can be used to increase the science exploration range by sending round-trip robotic missions to anywhere on the Moon using in-situ produced propellants.

Effects of mild processing pressures on the performance of dry powder inhaler formulations for inhalation therapy. 1: Budesonide and lactose.

PubMed

Marek, Steve R; Donovan, Martin J; Smyth, Hugh D C

2011-05-01

Batch-to-batch variability, whereby distinct batches of dry powder inhaler formulations, though manufactured with identical components and specifications, may exhibit significant variations in aerosol performance, is a major obstacle to consistent and reproducible drug delivery for inhalation therapy. This variability may arise from processing or manufacturing effects that have yet to be investigated. This study focused on the potential effects of mild compression forces experienced during powder manufacture and transport (such as during the filling of, or storage in, a hopper) on the flowability and aerosol performance of a lactose-based dry powder inhaler formulation. Different grades of inhalation lactose were subjected to typical compression forces by either placing a weight of known mass on the sample or by using a Texture Analyzer to apply a constant force while measuring the distance of compaction. Powder flowability was evaluated with a rotating drum apparatus by imaging the avalanching of the powder over time. The average avalanche angle and avalanche time were used to determine the flowability of each sample, both before and after compression treatment. Aerosol performance of treated and untreated lactose/budesonide blends (2% (w/w)) was assessed in dispersion studies using a next generation impactor. At compression forces in excess of 5 kPa, the flowability of milled lactose was decreased relative to the untreated sample. Compression of lactose prior to blending caused a decrease in in vitro aerosol dispersion performance. However, dispersion performance was unchanged when compression occurred subsequent to drug blending. In contrast, inhalation grade sieved lactose, differing from the milled grade with a lower concentration of lactose fines (<10 μm) and larger overall particle sizes, exhibited no statistical differences in either flowability or dispersion performance across all experimental treatments. Thus, the compression of the lactose fines onto the surfaces of the larger lactose particles due to mild processing pressures is hypothesized to be the cause of these observed performance variations. It was shown that simulations of storage and transport in an industrial scale hopper can induce significant variations in formulation performance, and it is speculated that this could be a source of batch-to-batch variations. Copyright © 2011 Elsevier B.V. All rights reserved.

Locust invasions and climatic factors from the Middle Ages to 1800

NASA Astrophysics Data System (ADS)

Camuffo, D.; Enzi, S.

1991-03-01

Locust migrations are strictly connected with climatic factors and a historical reconstruction of their invasions in Europe may be useful in dealing with this plague. From records of medieval chroniclers and more recent sources till 1800, some 100 detailed descriptions of locust invasions have been collected and analyzed. Some of them include the meteorological conditions which were associated with the arrival of the swarm of locusts, their path and the presumed country of origin, as well as the local effects such as famine and epidemics, these latter being mostly due to the putrification of the dead locusts. Once in Italy, by comparing different chronicles it is also possible to reconstruct the local march of the bands of hoppers, their extension, the periods in which they more frequently appear, the impact on human settlements, and sometimes the climatic factors (drop of temperature) which caused the swarm to die. The frequent observation of bands with “locusts and crickets” refers to hoppers of different instars, some of them in mature stage and others immature or moulting, born in convenient climatic conditions. By comparing the various chronicles it was also possible to reconstruct the local trajectory of the swarms, their extension, the periods when they were most frequent, their impact on the towns and villages and sometimes the climatic factors (mostly sharp drops in the temperature) responsible for the death of the swarms in northern and central Italy. According to the documentation perused, central-northern Italy was infested via two routes: 1) in most cases the locusts travelled up the Danube basin, then channelled through the Dinaric Alps and the Carpathians thus reaching the Hungarian Plain, and then being transported by the eastern winds to Italy; 2) very occasionally there were local invasions from the north, when the locusts descended through the Brenner Pass after reaching the Danube basin, and then moving along the Inn valley down to the River Adige. Such invasions occurred at the same time as those from the east. There was no specific mention of any invasion coming directly from Africa (as testified by Pliny in Naturalis Historia VI, 195, VII, 28 29) nor from the Spanish peninsula. The centuries worst affected by this scourge were the XIV and XVI, and to a lesser degree, the XVII. More recently, man has been increasingly effective in combatting the locusts.

Microgravity Storage Vessels and Conveying-Line Feeders for Cohesive Regolith

NASA Technical Reports Server (NTRS)

Walton, Otis R.; Vollmer, Hubert J.

2013-01-01

Under microgravity, the usual methods of placing granular solids into, or extracting them from, containers or storage vessels will not function. Alternative methods are required to provide a motive force to move the material. New configurations for microgravity regolith storage vessels that do not resemble terrestrial silos, hoppers, or tanks are proposed. The microgravity-compatible bulk-material storage vessels and exit feed configurations are designed to reliably empty and feed cohesive material to transfer vessels or conveying ducts or lines without gravity. A controllable motive force drives the cohesive material to the exit opening(s), and provides a reliable means to empty storage vessels and/or to feed microgravity conveying lines. The proposed designs will function equally well in vacuum, or inside of pressurized enclosures. Typical terrestrial granular solids handling and storage equipment will not function under microgravity, since almost all such equipment relies on gravity to at least move material to an exit location or to place it in the bottom of a container. Under microgravity, there effectively are no directions of up or down, and in order to effect movement of material, some other motive force must be applied to the material. The proposed storage vessels utilize dynamic centrifugal force to effect movement of regolith whenever material needs to be removed from the storage vessel. During simple storage, no dynamic motion or forces are required. The rotation rate during emptying can be controlled to ensure that material will move to the desired exit opening, even if the material is highly cohesive, or has acquired an electrostatic charge. The general concept of this Swirl Action Utilized for Centrifugal Ejection of Regolith (SAUCER) microgravity storage unit/dynamic feeder is to have an effective slot-hopper (based on the converging angles of the top and bottom conical section of the vessel) with an exit slot around the entire periphery of the SAUCER. The basic shape of such a unit is like two Chinese straw hats (douli) - one upside down, on the bottom, and another on top; or two wokpans, one upright on the bottom and another inverted on top, with a small gap between the upright and inverted pans or hats (around the periphery). A stationary outer ring, much like an unmounted bicycle tire, surrounds the gap between the two coaxial, nearly conical pieces, forming the top and bottom of the unit.

The golden mimicry complex uses a wide spectrum of defence to deter a community of predators

PubMed Central

Pekár, Stano; Petráková, Lenka; Bulbert, Matthew W; Whiting, Martin J; Herberstein, Marie E

2017-01-01

Mimicry complexes typically consist of multiple species that deter predators using similar anti-predatory signals. Mimics in these complexes are assumed to vary in their level of defence from highly defended through to moderately defended, or not defended at all. Here, we report a new multi-order mimicry complex that includes at least 140 different putative mimics from four arthropod orders including ants, wasps, bugs, tree hoppers and spiders. All members of this mimicry complex are characterised by a conspicuous golden body and an ant Gestalt, but vary substantially in their defensive traits. However, they were similarly effective at deterring predators - even mildly defended mimics were rarely eaten by a community of invertebrate and vertebrate predators both in the wild and during staged trials. We propose that despite the predominance of less defended mimics the three predatory guilds avoid the mimics because of the additive influence of the various defensive traits. DOI: http://dx.doi.org/10.7554/eLife.22089.001 PMID:28170317

Assessment of microwave-based clinical waste decontamination unit.

PubMed

Hoffman, P N; Hanley, M J

1994-12-01

A clinical waste decontamination unit that used microwave-generated heat was assessed for operator safety and efficacy. Tests with loads artificially contaminated with aerosol-forming particles showed that no particles were detected outside the machine provided the seals and covers were correctly seated. Thermometric measurement of a self-generated steam decontamination cycle was used to determine the parameters needed to ensure heat disinfection of the waste reception hopper, prior to entry for maintenance or repair. Bacterial and thermometric test pieces were passed through the machine within a full load of clinical waste. These test pieces, designed to represent a worst case situation, were enclosed in aluminium foil to shield them from direct microwave energy. None of the 100 bacterial test pieces yielded growth on culture and all 100 thermal test pieces achieved temperatures in excess of 99 degrees C during their passage through the decontamination unit. It was concluded that this method may be used to render safe the bulk of of ward-generated clinical waste.

Environmental assessment of a wood-waste-fired industrial watertube boiler. Volume 1. Technical results. Final report, March 1981-March 1984

DOE Office of Scientific and Technical Information (OSTI.GOV)

Castaldini, C.; Waterland, L.R.

1987-03-01

The two-volume report gives results from field tests of a wood-waste-fired industrial watertube boiler. Two series of tests were performed: one firing dry (11% moisture) wood waste, and the other firing green (34% moisture) wood waste. Emission measurements included: continuous monitoring of flue-gas emissions; source-assessment sampling system (SASS) sampling of the flue gas with subsequent laboratory analysis of samples to give total flue-gas organics in two boiling-point ranges, compound category information within these ranges, specific quantitation of the semi-volatile organic priority pollutants, and flue-gas concentrations of 73 trace elements; Method 5 sampling for particulate; controlled condensation system sampling for SO/submore » 2/ and SO/sub 3/; and grab sampling of boiler mechanical collector hopper ash for inorganic composition determinations. Total organic emissions decreased from 60-135 mg/dscm firing dry wood to 2-65 mg/dscm firing green wood, in parallel with corresponding boiler CO emissions.« less

Environmental assessment of a wood-waste-fired industrial watertube boiler. Volume 2. Data supplement. Final report, March 1981-March 1984

DOE Office of Scientific and Technical Information (OSTI.GOV)

Castaldini, C.; Waterland, L.R.

1987-03-01

The two-volume report gives results from field tests of a wood-waste-fired industrial watertube boiler. Two series of tests were performed: one firing dry (11% moisture) wood waste, and the other firing green (34% moisture) wood waste. Emission measurements included: continuous monitoring of flue-gas emissions; source-assessment sampling system (SASS) sampling of the flue-gas with subsequent laboratory analysis of samples to give total flue-gas organics in two boiling-point ranges, compound category information within these ranges, specific quantitation of the semi-volatile organic priority pollutants, and flue gas concentrations of 73 trace elements; Method 5 sampling for particulate; controlled condensation system sampling for SO/submore » 2/ and SO/sub 3/; and grab sampling of boiler mechanical collector hopper ash for inorganic and organic composition determinations. Total organic emissions decreased from 60-135 mg/dscm firing dry wood to 2-65 mg/dscm firing green wood, in parallel with corresponding boiler CO emissions.« less

KSC-2012-6405

NASA Image and Video Library

2012-09-20

CAPE CANAVERAL, Fla. -- At NASA’s Kennedy Space Center in Florida, a groundbreaking was held to mark the start of construction on the Antenna Test Bed Array for the Ka-Band Objects Observation and Monitoring, or Ka-BOOM system. Using ceremonial shovels to mark the site, from left are Michael Le, lead design engineer and construction manager Sue Vingris, Cape Design Engineer Co. project manager Kannan Rengarajan, chief executive officer of Cape Design Engineer Co. Lutfi Mized, president of Cape Design Engineer Co. David Roelandt, construction site superintendent with Cape Design Engineer Co. Marc Seibert, NASA project manager Michael Miller, NASA project manager Peter Aragona, KSC’s Electromagnetic Lab manager Stacy Hopper, KSCs master planning supervisor Dr. Bary Geldzabler, NASA chief scientist and KSC’s Chief Technologist Karen Thompson. The construction site is near the former Vertical Processing Facility, which has been demolished. Workers will begin construction on the pile foundations for the 40-foot-diameter dish antenna arrays and their associated utilities, and prepare the site for the operations command center facility. Photo credit: NASA/Charisse Nahser

KSC-2012-6404

NASA Image and Video Library

2012-09-20

CAPE CANAVERAL, Fla. -- At NASA’s Kennedy Space Center in Florida, a groundbreaking was held to mark the start of construction on the Antenna Test Bed Array for the Ka-Band Objects Observation and Monitoring, or Ka-BOOM system. Holding ceremonial shovels, from left are Michael Le, lead design engineer and construction manager Sue Vingris, Cape Design Engineer Co. project manager Kannan Rengarajan, chief executive officer of Cape Design Engineer Co. Lutfi Mized, president of Cape Design Engineer Co. David Roelandt, construction site superintendent with Cape Design Engineer Co. Marc Seibert, NASA project manager Michael Miller, NASA project manager Peter Aragona, KSC’s Electromagnetic Lab manager Stacy Hopper, KSCs master planning supervisor Dr. Bary Geldzabler, NASA chief scientist and KSC’s Chief Technologist Karen Thompson. The construction site is near the former Vertical Processing Facility, which has been demolished. Workers will begin construction on the pile foundations for the 40-foot-diameter dish antenna arrays and their associated utilities, and prepare the site for the operations command center facility. Photo credit: NASA/Charisse Nahser

Propulsion dynamics of lunar hoppers

NASA Technical Reports Server (NTRS)

Meetin, R. J.; Seifert, H. S.

1974-01-01

A feasibility study was recently completed on a hopping transporter concept for locomotion on the moon. Termed a Lunar Pogo because it would operate similarly to a conventional pogo stick, this vehicle would accelerate up an inclined leg, pick up the leg, and then enter ballistic flight over the moon's surface. Upon recontacting the lunar surface, the Lunar Pogo would decelerate down the leg. Propulsion would be provided by expansion of gas against a piston. Operation would be partially conservative because much of the energy expended by the gas during takeoff would be recovered by compressing the gas during landing. Two models of the ballistics and propulsion have been set up to estimate performance. The simplified first-order model illuminates the thermodynamics of ideal operation. The second-order model, which includes realistic effects such as sliding, provides a better approximation to actual performance. In a one-man Lunar Pogo, an astronaut would typically make 15-m (50-ft) leaps at an average speed of 5-8 km (3-5 miles) per hour.

The Experiment of the Clog Reduction in a Plane Silo

NASA Astrophysics Data System (ADS)

Sun, Ai-Le; Zhang, Jie

2017-06-01

The flow of particles may be clogged when they pass through a narrow orifice. Many factors can change the probability of clogging, such as the outlet size, the presence of obstacles and external perturbation, but the detailed mechanisms are still unclear. In this paper, we present an experimental study of reduction of the clogging probability in a horizontal plane silo, which consists of a layer of elastic particles transported on an annular flat plate rotating with a constant angular velocity passing through a hopper structure. We found the exponential distributions of the avalanche size for different sizes of orifice and the power law tails of the passing time between two particles. We did not confirm whether there was a critical size of orifice above which the clogging became impossible. We explored the effect of the obstacle on the probability of clogging: and if we chose a proper obstacle placed at a proper position, the probability of clogging could be reduced by a factor of about seven.

Intercropping for Management of Insect Pests of Castor, Ricinus communis, in the Semi—Arid Tropics of India

PubMed Central

Srinivasa Rao, M.; Venkateswarlu, B.

2012-01-01

Intercropping is one of the important cultural practices in pest management and is based on the principle of reducing insect pests by increasing the diversity of an ecosystem. On—farm experiments were conducted in villages of semi—arid tropical (SAT) India to identify the appropriate combination of castor (Ricinus communis L.) (Malpighiales: Euphorbiaceae) and intercropping in relation to pest incidence. The diversity created by introducing cluster bean, cowpea, black gram, or groundnut as intercrops in castor (1:2 ratio proportions) resulted in reduction of incidence of insect pests, namely semilooper (Achaea janata L.), leaf hopper (Empoasca flavescens Fabricius), and shoot and capsule borer (Conogethes punctiferalis Guenee). A buildup of natural enemies (Microplitis, coccinellids, and spiders) of the major pests of castor was also observed in these intercropping systems and resulted in the reduction of insect pests. Further, these systems were more efficient agronomically and economically, and were thus more profitable than a castor monocrop. PMID:22934569

Development of a kolanut peeling device.

PubMed

Kareem, I; Owolarafe, O K; Ajayi, O A

2014-10-01

A kolanut peeling machine was designed, constructed and evaluated for the postharvest processing of the seed. The peeling machine consists of a standing frame, peeling unit and hopper. The peeling unit consists of a special paddle, which mixes the kolanut, rubs them against one another and against the wall of the barrel and also conveys the kolanut to the outlet. The performance of the kolanut peeling machine was evaluated for its peeling efficiency at different moisture content (53.0, 57.6, 61.4 % w.b.) and speeds of operation of the machine. The result of the analysis of variance shows that the main factors and their interaction had significant effects (p < 0.05) on the peeling efficiency of the machine. The result also shows that the peeling efficiency of the machine increased as the moisture content increase and decreased with increase in machine speed. The highest efficiency of the machine was 60.3 % at a moisture content of 61.4 % w.b. and speed of 40 rpm.

Autonomous Onboard Science Data Analysis for Comet Missions

NASA Technical Reports Server (NTRS)

Thompson, David R.; Tran, Daniel Q.; McLaren, David; Chien, Steve A.; Bergman, Larry; Castano, Rebecca; Doyle, Richard; Estlin, Tara; Lenda, Matthew

2012-01-01

Coming years will bring several comet rendezvous missions. The Rosetta spacecraft arrives at Comet 67P/Churyumov-Gerasimenko in 2014. Subsequent rendezvous might include a mission such as the proposed Comet Hopper with multiple surface landings, as well as Comet Nucleus Sample Return (CNSR) and Coma Rendezvous and Sample Return (CRSR). These encounters will begin to shed light on a population that, despite several previous flybys, remains mysterious and poorly understood. Scientists still have little direct knowledge of interactions between the nucleus and coma, their variation across different comets or their evolution over time. Activity may change on short timescales so it is challenging to characterize with scripted data acquisition. Here we investigate automatic onboard image analysis that could act faster than round-trip light time to capture unexpected outbursts and plume activity. We describe one edge-based method for detect comet nuclei and plumes, and test the approach on an existing catalog of comet images. Finally, we quantify benefits to specific measurement objectives by simulating a basic plume monitoring campaign.

Development of a Rational Design Space for Optimizing Mixing Conditions for Formation of Adhesive Mixtures for Dry-Powder Inhaler Formulations.

PubMed

Sarkar, Saurabh; Minatovicz, Bruna; Thalberg, Kyrre; Chaudhuri, Bodhisattwa

2017-01-01

The purpose of the present study was to develop guidance toward rational choice of blenders and processing conditions to make robust and high performing adhesive mixtures for dry-powder inhalers and to develop quantitative experimental approaches for optimizing the process. Mixing behavior of carrier (LH100) and AstraZeneca fine lactose in high-shear and low-shear double cone blenders was systematically investigated. Process variables impacting the mixing performance were evaluated for both blenders. The performance of the blenders with respect to the mixing time, press-on forces, static charging, and abrasion of carrier fines was monitored, and for some of the parameters, distinct differences could be detected. A comparison table is presented, which can be used as a guidance to enable rational choice of blender and process parameters based on the user requirements. Segregation of adhesive mixtures during hopper discharge was also investigated. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Mesoionic insecticides: a novel class of insecticides that modulate nicotinic acetylcholine receptors.

PubMed

Holyoke, Caleb W; Cordova, Daniel; Zhang, Wenming; Barry, James D; Leighty, Robert M; Dietrich, Robert F; Rauh, James J; Pahutski, Thomas F; Lahm, George P; Tong, My-Hanh Thi; Benner, Eric A; Andreassi, John L; Smith, Rejane M; Vincent, Daniel R; Christianson, Laurie A; Teixeira, Luis A; Singh, Vineet; Hughes, Kenneth A

2017-04-01

As the world population grows towards 9 billion by 2050, it is projected that food production will need to increase by 60%. A critical part of this growth includes the safe and effective use of insecticides to reduce the estimated 20-49% loss of global crop yields owing to pests. The development of new insecticides will help to sustain this protection and overcome insecticide resistance. A novel class of mesoionic compounds has been discovered, with exceptional insecticidal activity on a range of Hemiptera and Lepidoptera. These compounds bind to the orthosteric site of the nicotinic acetylcholine receptor and result in a highly potent inhibitory action at the receptor with minimal agonism. The synthesis, biological activity, optimization and mode of action will be discussed. Triflumezopyrim insect control will provide a powerful tool for control of hopper species in rice throughout Asia. Dicloromezotiaz can provide a useful control tool for lepidopteran pests, with an underexploited mode of action among these pests. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

DEM study of granular flow around blocks attached to inclined walls

NASA Astrophysics Data System (ADS)

Samsu, Joel; Zhou, Zongyan; Pinson, David; Chew, Sheng

2017-06-01

Damage due to intense particle-wall contact in industrial applications can cause severe problems in industries such as mineral processing, mining and metallurgy. Studying the flow dynamics and forces on containing walls can provide valuable feedback for equipment design and optimising operations to prolong the equipment lifetime. Therefore, solids flow-wall interaction phenomena, i.e. induced wall stress and particle flow patterns should be well understood. In this work, discrete element method (DEM) is used to study steady state granular flow in a gravity-fed hopper like geometry with blocks attached to an inclined wall. The effects of different geometries, e.g. different wall angles and spacing between blocks are studied by means of a 3D DEM slot model with periodic boundary conditions. The findings of this work include (i) flow analysis in terms of flow patterns and particle velocities, (ii) force distributions within the model geometry, and (iii) wall stress vs. model height diagrams. The model enables easy transfer of the key findings to other industrial applications handling granular materials.

Fiber optic interferometry for industrial process monitoring and control applications

NASA Astrophysics Data System (ADS)

Marcus, Michael A.

2002-02-01

Over the past few years we have been developing applications for a high-resolution (sub-micron accuracy) fiber optic coupled dual Michelson interferometer-based instrument. It is being utilized in a variety of applications including monitoring liquid layer thickness uniformity on coating hoppers, film base thickness uniformity measurement, digital camera focus assessment, optical cell path length assessment and imager and wafer surface profile mapping. The instrument includes both coherent and non-coherent light sources, custom application dependent optical probes and sample interfaces, a Michelson interferometer, custom electronics, a Pentium-based PC with data acquisition cards and LabWindows CVI or LabView based application specific software. This paper describes the development evolution of this instrument platform and applications highlighting robust instrument design, hardware, software, and user interfaces development. The talk concludes with a discussion of a new high-speed instrument configuration, which can be utilized for high speed surface profiling and as an on-line web thickness gauge.

Effect of moisture content on the flowability of crushed ores

NASA Astrophysics Data System (ADS)

Cabrejos, Francisco

2017-06-01

In many mining and industrial processes where large quantities of non-degrading bulk materials such as crushed ores are handled, silos, hoppers, stockpiles and chutes are widely used because they are economical and reliable (if properly designed and operated). However, they are not free of trouble and may experience flow problems such as arching, ratholing, erratic flow, limited storage capacity, limited discharge flow rate, caking, segregation and/or flooding. Moisture content and fine particles significantly affect the flowability of most ores, increasing their cohesive strength and turning them more prone to these problems. The purpose of this article is to highlight a proven, scientific method that can be utilized to ensure reliable storage, flow and discharge of bulk solids in these equipment based on Jenike's flow-of-solids theory and laboratory testing. Knowledge of the flow properties of the material handled provides a design basis to ensure mass flow, avoid arching and prevent the formation of "ratholes". The effect of an increase in water content of the ore is discussed with experimental results.

Rapid granular flows on a rough incline: phase diagram, gas transition, and effects of air drag.

PubMed

Börzsönyi, Tamás; Ecke, Robert E

2006-12-01

We report experiments on the overall phase diagram of granular flows on an incline with emphasis on high inclination angles where the mean layer velocity approaches the terminal velocity of a single particle free falling in air. The granular flow was characterized by measurements of the surface velocity, the average layer height, and the mean density of the layer as functions of the hopper opening, the plane inclination angle, and the downstream distance x of the flow. At high inclination angles the flow does not reach an x -invariant steady state over the length of the inclined plane. For low volume flow rates, a transition was detected between dense and very dilute (gas) flow regimes. We show using a vacuum flow channel that air did not qualitatively change the phase diagram and did not quantitatively modify mean flow velocities of the granular layer except for small changes in the very dilute gaslike phase.

Autoshaping as a function of prior food presentations1

PubMed Central

Downing, Kevin; Neuringer, Allen

1976-01-01

Young chickens were given 1, 10, 100, or 1000 presentations of grain in a hopper. Subsequently, the key was illuminated before each presentation of grain to study autoshaping of the key-peck response. The number of keylight-grain pairings before a bird first pecked the lighted key was found to be a U-shaped function of the number of prior food-only presentations, with pecks occurring significantly sooner after 100 food-only trials than after any of the other values. Two of five chicks at the 100-trial value pecked on the first illumination of the key. Experiment II showed further that when a series of food-only trials (no keylight) preceded keylight-only trials (no food) 30% of the chicks pecked the illuminated key. Experiment III extended the generality of first-trial pecking to pigeons. After preliminary training with food-only, two of five pigeons pecked on the first illumination of a key. The results suggest a close relationship between autoshaping and pseudo-conditioning. PMID:16811961

Autoshaping as a function of prior food presentations.

PubMed

Downing, K; Neuringer, A

1976-11-01

Young chickens were given 1, 10, 100, or 1000 presentations of grain in a hopper. Subsequently, the key was illuminated before each presentation of grain to study autoshaping of the key-peck response. The number of keylight-grain pairings before a bird first pecked the lighted key was found to be a U-shaped function of the number of prior food-only presentations, with pecks occurring significantly sooner after 100 food-only trials than after any of the other values. Two of five chicks at the 100-trial value pecked on the first illumination of the key. Experiment II showed further that when a series of food-only trials (no keylight) preceded keylight-only trials (no food) 30% of the chicks pecked the illuminated key. Experiment III extended the generality of first-trial pecking to pigeons. After preliminary training with food-only, two of five pigeons pecked on the first illumination of a key. The results suggest a close relationship between autoshaping and pseudo-conditioning.

MARCO POLO: near earth object sample return mission

NASA Astrophysics Data System (ADS)

Barucci, M. A.; Yoshikawa, M.; Michel, P.; Kawagushi, J.; Yano, H.; Brucato, J. R.; Franchi, I. A.; Dotto, E.; Fulchignoni, M.; Ulamec, S.

2009-03-01

MARCO POLO is a joint European-Japanese sample return mission to a Near-Earth Object. This Euro-Asian mission will go to a primitive Near-Earth Object (NEO), which we anticipate will contain primitive materials without any known meteorite analogue, scientifically characterize it at multiple scales, and bring samples back to Earth for detailed scientific investigation. Small bodies, as primitive leftover building blocks of the Solar System formation process, offer important clues to the chemical mixture from which the planets formed some 4.6 billion years ago. Current exobiological scenarios for the origin of Life invoke an exogenous delivery of organic matter to the early Earth: it has been proposed that primitive bodies could have brought these complex organic molecules capable of triggering the pre-biotic synthesis of biochemical compounds. Moreover, collisions of NEOs with the Earth pose a finite hazard to life. For all these reasons, the exploration of such objects is particularly interesting and urgent. The scientific objectives of MARCO POLO will therefore contribute to a better understanding of the origin and evolution of the Solar System, the Earth, and possibly Life itself. Moreover, MARCO POLO provides important information on the volatile-rich (e.g. water) nature of primitive NEOs, which may be particularly important for future space resource utilization as well as providing critical information for the security of Earth. MARCO POLO is a proposal offering several options, leading to great flexibility in the actual implementation. The baseline mission scenario is based on a launch with a Soyuz-type launcher and consists of a Mother Spacecraft (MSC) carrying a possible Lander named SIFNOS, small hoppers, sampling devices, a re-entry capsule and scientific payloads. The MSC leaves Earth orbit, cruises toward the target with ion engines, rendezvous with the target, conducts a global characterization of the target to select a sampling site, and delivers small hoppers (MINERVA type, JAXA) and SIFNOS. The latter, if added, will perform a soft landing, anchor to the target surface, and make various in situ measurements of surface/subsurface materials near the sampling site. Two surface samples will be collected by the MSC using “touch and go” manoeuvres. Two complementary sample collection devices will be used in this phase: one developed by ESA and another provided by JAXA, mounted on a retractable extension arm. After the completion of the sampling and ascent of the MSC, the arm will be retracted to transfer the sample containers into the MSC. The MSC will then make its journey back to Earth and release the re-entry capsule into the Earth’s atmosphere.

Entrainment of Dungeness Crab in the Desdemona Shoals Reach of the Lower Columbia River Navigation Channel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pearson, Walter H.; Kohn, Nancy P.; Skalski, J. R.

2006-09-30

Proposed dredging of the Columbia River has raised concerns about related impacts on Dungeness crab in the Columbia River Estuary (CRE). This study follows two major efforts, sponsored by the Portland District of the U. S. Army Corps of Engineers (USACE) to quantify the number of crabs entrained by a hopper dredge working in the CRE. From June 2002 through September 2002, Pacific Northwest National Laboratory (PNNL) conducted direct measurements of crab entrainment in the CRE from the mouth of the Columbia River (MCR, river mile -3 to +3) upriver as far as Miller Sands (river mile 21 to 24).more » These studies constituted a major step in quantifying crab entrainment in the CRE, and allowed statistically bounded projections of adult equivalent loss (AEL) for Dungeness crab populations under a range of future construction dredging and maintenance dredging scenarios (Pearson et al. 2002, 2003). In 2004, PNNL performed additional measurements to improve estimates of crab entrainment at Desdemona Shoals and at Flavel Bar, a reach near Astoria that had not been adequately sampled in 2002 (Figure 1). The 2004 data were used to update the crab loss projections for channel construction to 43 ft MLLW. In addition, a correlation between bottom salinity and adult (age 2+ and 3+, >100 mm carapace width) crab entrainment was developed using 2002 data, and elaborated upon with the 2004 data. This crab salinity model was applied to forecasting seasonal (monthly) entrainment rates and AEL using seasonal variations in salinity (Pearson et al. 2005). In the previous studies, entrainment rates in Desdemona Shoals were more variable than in any of the other reaches. Pearson et al. (2005) concluded that ?the dynamics behind the variable entrainment rates at Desdemona Shoals are not fully understood,? as well as finding that juvenile crab entrainment was not significantly correlated with salinity as it was for older crab. The present study was undertaken to address the question of whether the high age 1+ entrainment rate at Desdemona Shoals in June 2002 unusual, or would it be observed again under similar conditions? PNNL and USACE personnel directly measured crab entrainment by the USACE hopper dredge Essayons working in Desdemona Shoals in June 2006. In addition to quantifying crab entrainment of all age classes, bottom salinity was directly measured in as many samples as possible, so that the relationship between crab entrainment and salinity could be further evaluated. All 2006 data were collected and analyzed in a manner consistent with the previous entrainment studies (Pearson et al. 2002, 2003, 2005).« less

The learning curve: Implications of a quantitative analysis

PubMed Central

Gallistel, Charles R.; Fairhurst, Stephen; Balsam, Peter

2004-01-01

The negatively accelerated, gradually increasing learning curve is an artifact of group averaging in several commonly used basic learning paradigms (pigeon autoshaping, delay- and trace-eye-blink conditioning in the rabbit and rat, autoshaped hopper entry in the rat, plus maze performance in the rat, and water maze performance in the mouse). The learning curves for individual subjects show an abrupt, often step-like increase from the untrained level of responding to the level seen in the well trained subject. The rise is at least as abrupt as that commonly seen in psychometric functions in stimulus detection experiments. It may indicate that the appearance of conditioned behavior is mediated by an evidence-based decision process, as in stimulus detection experiments. If the appearance of conditioned behavior is taken instead to reflect the increase in an underlying associative strength, then a negligible portion of the function relating associative strength to amount of experience is behaviorally visible. Consequently, rate of learning cannot be estimated from the group-average curve; the best measure is latency to the onset of responding, determined for each subject individually. PMID:15331782

Hot Water Propulsion for Horizontal Rocket Assisted Take-Off Systems for Future Reusable Launch Vehicles

NASA Astrophysics Data System (ADS)

Pilz, N.; Adirim, H.; Lo, R.; Schildknecht, A.

2004-10-01

Among other concepts, reusable space transportation systems that comprise winged reusable launch vehicles (RLV) with horizontal take-off and horizontal landing (HTHL) are under worldwide investigation, e.g. the respective concepts within ESA's FESTIP-Study (Future European Space Transportation Integration Program) or the HOPPER concept by EADS-ST. The payload of these RLVs could be significantly increased by means of a ground-based take-off assistance system that would accelerate the vehicle along a horizontal track until it reaches the desired speed to ignite its onboard engines for leaving the ground and launching into orbit. This paper illustrates the advantages of horizontal take-off for winged RLVs and provides an overview of launch-assist options for HTHL RLVs. It presents hot water propulsion for ground-based take-off assistance systems for future RLVs as an attractive choice besides magnetic levitation and acceleration (maglev) technology. Finally, preliminary design concepts are presented for a rocket assisted take-off system (RATOS) with hot water propulsion followed by an analysis of its improvement potential.

SERI Solar Energy Storage Program: FY 1984

NASA Astrophysics Data System (ADS)

Luft, W.; Bohn, M.; Copeland, R. J.; Kreith, F.; Nix, R. G.

1985-02-01

The activities of the Solar Energy Research Institute's Solar Energy Research Institute's Solar Energy Storage Program during its sixth year are summarized. During FY 1984 a study was conducted to identify the most promising high-temperature containment concepts considering corrosion resistance, material strength at high temperature, reliability of performance, and cost. Of the two generic types of high-temperature thermal storage concepts, the single-tank system was selected using a two-medium approach to the thermocline maintenance. This concept promises low costs, but further research is required. A conceptual design for a sand-to-air direct-contact heat exchanger was developed using dual-lock hoppers to introduce the sand into the fluidized-bed exchanger, and using cyclones to remove sand particles from the output air stream. Preliminary cost estimates indicate heat exchanger subsystem annual levelized costs of about $4/GJ with compressor costs of an additional $0.75/GJ. An economic analysis comparing sensible and latent heat storage for nitrate and carbonate salts with solely sensible heat storage showed 3%-21% cost savings with combined sensible and latent heat storage.

Evolution of Regolith Feed Systems for Lunar ISRU 02 Production Plants

NASA Technical Reports Server (NTRS)

Mueller, Robert P.; Townsend, Ivan I., III; Mantovani, James G.; Metzger, Philip T.

2010-01-01

The In-Situ Resource Utilization (ISRU) project of the NASA Constellation Program, Exploration Technology Development Program (ETDP) has been engaged in the design and testing of various Lunar ISRU O2 production plant prototypes that can extract chemically bound oxygen from the minerals in the lunar regolith. This work demands that lunar regolith (or simulants) shall be introduced into the O2 production plant from a holding bin or hopper and subsequently expelled from the ISRU O2 production plant for disposal. This sub-system is called the Regolith Feed System (RFS) which exists in a variety of configurations depending on the O2 production plant oxygen being used (e.g. Hydrogen Reduction, Carbothermal, Molten Oxide Electrolysis). Each configuration may use a different technology and in addition it is desirable to have heat recuperation from the spent hot regolith as an integral part of the RFS. This paper addresses the various RFS and heat recuperation technologies and system configurations that have been developed under the NASA ISRU project since 2007. In addition current design solutions and lessons learned from reduced gravity flight testing will be discussed.

Demonstration of Critical Systems for Propellant Production on Mars for Science and Exploration Missions

NASA Technical Reports Server (NTRS)

Linne, Diane L.; Gaier, James R.; Zoeckler, Joseph G.; Kolacz, John S.; Wegeng, Robert S.; Rassat, Scot D.; Clark, D. Larry

2013-01-01

A Mars hopper has been proposed as a Mars mobility concept that will also demonstrate and advance in-situ resource utilization. The components needed in a Mars propellant production plant have been developed to various levels of technology maturity, but there is little experience with the systems in a Mars environment. Two systems for the acquisition and compression of the thin carbon dioxide atmosphere were designed, assembled, and tested in a Mars environment chamber. A microchannel sorption pump system was able to raise the pressure from 7 Torr to 450 Torr or from 12 Torr to over 700 Torr in two stages. This data now provides information needed to make additional improvements in the sorption pump technology to increase performance, although a system-level analysis might prove that some amount of pre- or post-compression may be a preferred solution. A mini cryofreezer system was also evaluated as an alternative method for carbon dioxide acquisition and compression. Finally, an electrolysis system was tested and successfully demonstrated start-up operation and thermal stability of all components during long-term operation in the chamber.

Preliminary design of four aircraft to service the California Corridor in the year 2010: The California Condor, California Sky-Hopper, high capacity short range transport tilt rotor aircraft needed to simplify intercity transportation

NASA Technical Reports Server (NTRS)

1989-01-01

The major objective of this project was to design an aircraft for use in the California Corridor in the year 2010. The design process, completed by students in a senior design class at California Polytechnic State University, San Luis Obispo, used a Class 1 airplane design analysis from Jan Roskam's Airplane Design. The California Condor (CC-38), a 38 passenger, 400 mph aircraft, was designed to meet the needs of tomorrow's passengers while conforming to the California Corridor's restrictions. Assumptions were made using today's technology with forecasts into 21st Century technology. Doubling today's commuter aircraft passenger capacity, travelling at Mach .57 with improved cruise efficiencies of over 10 percent, with the ability to land within field lengths of 4000 feet, are the CC-38's strongest points. The California Condor has a very promising future in helping to relieve the air traffic and airport congestion in the 21st Century.

Method for preventing jamming conditions in a compression device

DOEpatents

Williams, Paul M.; Faller, Kenneth M.; Bauer, Edward J.

2002-06-18

A compression device for feeding a waste material to a reactor includes a waste material feed assembly having a hopper, a supply tube and a compression tube. Each of the supply and compression tubes includes feed-inlet and feed-outlet ends. A feed-discharge valve assembly is located between the feed-outlet end of the compression tube and the reactor. A feed auger-screw extends axially in the supply tube between the feed-inlet and feed-outlet ends thereof. A compression auger-screw extends axially in the compression tube between the feed-inlet and feed-outlet ends thereof. The compression tube is sloped downwardly towards the reactor to drain fluid from the waste material to the reactor and is oriented at generally right angle to the supply tube such that the feed-outlet end of the supply tube is adjacent to the feed-inlet end of the compression tube. A programmable logic controller is provided for controlling the rotational speed of the feed and compression auger-screws for selectively varying the compression of the waste material and for overcoming jamming conditions within either the supply tube or the compression tube.

Human genetic resistance to malaria.

PubMed

Williams, Thomas N

2009-01-01

This brief chapter highlights the need for caution when designing and interpreting studies aimed at seeking new genes that may be associated with malaria protection, or investigating the potential mechanisms for protection in promising candidates. Judging genetic effects on the basis of the wrong clinical phenotype and missing true protective genes because their protective effects are masked by unpredictable epistatic effects are major potential pitfalls. These issues are by no means unique to malaria: in recent years, the importance of larger sample sizes and careful phenotypic definitions have become appreciated increasingly, particularly for genome-wide studies of complex diseases (Cordell and Clayton, 2005; Burton, Tobin and Hopper, 2005). Until recently, research in the field of malaria genetics has not enjoyed the sort of funding afforded to similar work investigating diseases of importance to the developed world. However, in the last few years, coupled with advances in genetic diagnostics that have led to massive automation and falling costs per gene explored, momentum has grown towards more generous funding that brings with it the opportunity for much larger, multisite cohesive studies. The stage is set for a giant leap forward in the coming years.

National Coal Quality Inventory (NACQI)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robert Finkelman

2005-09-30

The U.S. Geological Survey (USGS) conducted the National Coal Quality Inventory (NaCQI) between 1999 and 2005 to address a need for quality information on coals that will be mined during the next 20-30 years. Collaboration between the USGS, State geological surveys, universities, coal burning utilities, and the coal mining industry plus funding support from the Electric Power Research Institute (EPRI) and the U.S. Department of Energy (DOE) permitted collection and submittal of coal samples for analysis. The chemical data (proximate and ultimate analyses; major, minor and trace element concentrations) for 729 samples of raw or prepared coal, coal associated shale,more » and coal combustion products (fly ash, hopper ash, bottom ash and gypsum) from nine coal producing States are included. In addition, the project identified a new coal reference analytical standard, to be designated CWE-1 (West Elk Mine, Gunnison County, Colorado) that is a high-volatile-B or high-volatile-A bituminous coal with low contents of ash yield and sulfur, and very low, but detectable contents of chlorine, mercury and other trace elements.« less

Why do mammals hop? Understanding the ecology, biomechanics and evolution of bipedal hopping.

PubMed

McGowan, Craig P; Collins, Clint E

2018-06-15

Bipedal hopping is a specialized mode of locomotion that has arisen independently in at least five groups of mammals. We review the evolutionary origins of these groups, examine three of the most prominent hypotheses for why bipedal hopping may have arisen, and discuss how this unique mode of locomotion influences the behavior and ecology of modern species. While all bipedal hoppers share generally similar body plans, differences in underlying musculoskeletal anatomy influence what performance benefits each group may derive from this mode of locomotion. Based on a review of the literature, we conclude that the most likely reason that bipedal hopping evolved is associated with predator avoidance by relatively small species in forested environments. Yet, the morphological specializations associated with this mode of locomotion have facilitated the secondary acquisition of performance characteristics that enable these species to be highly successful in ecologically demanding environments such as deserts. We refute many long-held misunderstandings about the origins of bipedal hopping and identify potential areas of research that would advance the understanding of this mode of locomotion. © 2018. Published by The Company of Biologists Ltd.

Development of adolescents' peer crowd identification in relation to changes in problem behaviors.

PubMed

Doornwaard, Suzan M; Branje, Susan; Meeus, Wim H J; ter Bogt, Tom F M

2012-09-01

This 5-wave longitudinal study, which included 1,313 Dutch adolescents, examined the development of peer crowd identification in relation to changes in problem behaviors. Adolescents from 2 age cohorts annually reported their identification with 7 peer crowds and their levels of internalizing and externalizing problem behaviors. Univariate latent growth curve analyses revealed declines (i.e., "Hip Hoppers" and "Metal Heads") or declines followed by stabilization (i.e., "Nonconformists") in identification with nonconventional crowds and increases (i.e., "Elites" and "Brains") or declines followed by stabilization (i.e., "Normals" and "Jocks") in identification with conventional crowds. Multivariate latent growth curve analyses indicated that stronger and more persistent identifications with nonconventional crowds were generally associated with more problem behaviors throughout adolescence. In contrast, stronger and more persistent identifications with conventional crowds were generally associated with fewer problem behaviors throughout adolescence with the notable exception of Brains, who showed a mixed pattern. Though characterized by fewer externalizing problems, this group did report more anxiety problems. These findings and their implications are discussed. PsycINFO Database Record (c) 2012 APA, all rights reserved.

The learning curve: implications of a quantitative analysis.

PubMed

Gallistel, Charles R; Fairhurst, Stephen; Balsam, Peter

2004-09-07

The negatively accelerated, gradually increasing learning curve is an artifact of group averaging in several commonly used basic learning paradigms (pigeon autoshaping, delay- and trace-eye-blink conditioning in the rabbit and rat, autoshaped hopper entry in the rat, plus maze performance in the rat, and water maze performance in the mouse). The learning curves for individual subjects show an abrupt, often step-like increase from the untrained level of responding to the level seen in the well trained subject. The rise is at least as abrupt as that commonly seen in psychometric functions in stimulus detection experiments. It may indicate that the appearance of conditioned behavior is mediated by an evidence-based decision process, as in stimulus detection experiments. If the appearance of conditioned behavior is taken instead to reflect the increase in an underlying associative strength, then a negligible portion of the function relating associative strength to amount of experience is behaviorally visible. Consequently, rate of learning cannot be estimated from the group-average curve; the best measure is latency to the onset of responding, determined for each subject individually.

Screening for Learning and Memory Mutations: A New Approach.

PubMed

Gallistel, C R; King, A P; Daniel, A M; Freestone, D; Papachristos, E B; Balci, F; Kheifets, A; Zhang, J; Su, X; Schiff, G; Kourtev, H

2010-01-30

We describe a fully automated, live-in 24/7 test environment, with experimental protocols that measure the accuracy and precision with which mice match the ratio of their expected visit durations to the ratio of the incomes obtained from two hoppers, the progress of instrumental and classical conditioning (trials-to-acquisition), the accuracy and precision of interval timing, the effect of relative probability on the choice of a timed departure target, and the accuracy and precision of memory for the times of day at which food is available. The system is compact; it obviates the handling of the mice during testing; it requires negligible amounts of experimenter/technician time; and it delivers clear and extensive results from 3 protocols within a total of 7-9 days after the mice are placed in the test environment. Only a single 24-hour period is required for the completion of first protocol (the matching protocol), which is strong test of temporal and spatial estimation and memory mechanisms. Thus, the system permits the extensive screening of many mice in a short period of time and in limited space. The software is publicly available.

Sustainable Mars Sample Return

NASA Technical Reports Server (NTRS)

Alston, Christie; Hancock, Sean; Laub, Joshua; Perry, Christopher; Ash, Robert

2011-01-01

The proposed Mars sample return mission will be completed using natural Martian resources for the majority of its operations. The system uses the following technologies: In-Situ Propellant Production (ISPP), a methane-oxygen propelled Mars Ascent Vehicle (MAV), a carbon dioxide powered hopper, and a hydrogen fueled balloon system (large balloons and small weather balloons). The ISPP system will produce the hydrogen, methane, and oxygen using a Sabatier reactor. a water electrolysis cell, water extracted from the Martian surface, and carbon dioxide extracted from the Martian atmosphere. Indigenous hydrogen will fuel the balloon systems and locally-derived methane and oxygen will fuel the MAV for the return of a 50 kg sample to Earth. The ISPP system will have a production cycle of 800 days and the estimated overall mission length is 1355 days from Earth departure to return to low Earth orbit. Combining these advanced technologies will enable the proposed sample return mission to be executed with reduced initial launch mass and thus be more cost efficient. The successful completion of this mission will serve as the next step in the advancement of Mars exploration technology.

Preliminary study of the characteristics of a high Mg containing Al-Mg-Si alloy

NASA Astrophysics Data System (ADS)

Yan, F.; McKay, B. J.; Fan, Z.; Chen, M. F.

2012-01-01

An Al-20Mg-4Si high Mg containing alloy has been produced and its characteristics investigated. The as-cast alloy revealed primary Mg2Si particles evenly distributed throughout an α-Al matrix with a β-Al3Mg2 fully divorced eutectic phase observed in interdendritic regions. The Mg2Si particles displayed octahedral, truncated octahedral, and hopper morphologies. Additions of Sb, Ti and Zr had a refining influence reducing the size of the Mg2Si from 52 ± 4 μm to 25 ± 0.1 μm, 35 ± 1 μm and 34 ± 1 μm respectively. HPDC tensile test samples could be produced with a 0.6 wt.% Mn addition which prevented die soldering. Solution heating for 1 hr was found to dissolve the majority of the Al3Mg2 eutectic phase with no evidence of any effect on the primary Mg2Si. Preliminary results indicate that the heat treatment has a beneficial effect on the elongation and the UTS.

Studies of Shock Wave Interaction with a Curtain of Massive Particles

NASA Astrophysics Data System (ADS)

Lingampally, Sumanth Reddy; Wayne, Patrick; Cooper, Sean; Izard, Ricardo Gonzalez; Jacobs, Gustaaf; Vorobieff, Peter

2017-11-01

Interaction of a shock wave with planar and perturbed curtain of massive particles is studied experimentally. To form the curtain, solid soda lime particles (30-50 micron diameter) are dropped from a hopper fitted with mesh sieves and vibrated with a motor. The curtain forms when the particles move through a rectangular slot in the top of the test section of the shock tube used in experiment. The curtain can be either planar or perturbed in the horizontal plane (parallel to the shock direction) based on the shape of the slot. This setup generates a particle curtain with a volume fraction varying between 2 and 8 percent along its vertical height. A laser illuminates the curtain in vertical and horizontal planes. When the diaphragm separating the driver and the driven section is ruptured, shock waves with Mach numbers ranging from 1 to 2, depending on the pressure, propagate down the driven section and into test section. The phenomena following the shock wave impingement on the particle curtain are captured using an Apogee Alta U42 camera. This work is supported by the National Science Foundation Grant 1603915/1603326.

Effect of enriched housing on welfare, production performance and meat quality in finishing lambs: the use of feeder ramps.

PubMed

Aguayo-Ulloa, L A; Miranda-de la Lama, G C; Pascual-Alonso, M; Olleta, J L; Villarroel, M; Sañudo, C; María, G A

2014-05-01

This study analyses the effect of environmental enrichment on the welfare, productive traits and meat quality of lambs housed in feedlots. Sixty lambs were placed in enriched (EE) or conventional (CO) pens (3 pens for each treatment, 10 lambs/pen) where EE had a wooden platform with ramps that provided access to a concentrate hopper, cereal straw as bedding and forage, and one play ramp. The CO pen was barren, similar to commercial feedlots. The physiological adaptation response of EE lambs was more efficient than CO, since the latter mobilised more body reserves (i.e., increased NEFA, P<0.05), and had lower levels of immunity (i.e., increased N/L, P<0.05), which indicate chronic stress, probably associated with the barren environment. The EE lambs had a higher (P<0.05) average daily gain, with heavier carcasses and higher fattening scores, as well as lower pHult, higher L and b values, and lower values of texture (P<0.05). Copyright © 2014 Elsevier Ltd. All rights reserved.

NTP Toxicity Study Report on the atmospheric characterization, particle size, chemical composition, and workplace exposure assessment of cellulose insulation (CELLULOSEINS).

PubMed

Morgan, Daniel L

2006-08-01

Cellulose insulation (CI) is a type of thermal insulation produced primarily from recycled newspapers. The newspapers are shredded, milled, and treated with fire-retardant chemicals. The blowing process for installing CI generates a significant quantity of airborne material that presents a potential inhalation hazard to workers. CI was selected for study based upon the high production volume, the potential for widespread human exposure, and a lack of toxicity data; insufficient information was available to determine whether inhalation studies in laboratory animals were technically feasible or necessary. Studies were conducted to characterize the chemical and physical properties of CI aerosols, to evaluate the potential acute pulmonary toxicity of CI, and to assess occupational exposure of CI installers. Workplace exposure assessments were conducted in collaboration with the National Institute for Occupational Safety and Health (NIOSH, 2001). Chemical analyses were performed on samples of bulk CI from four major United States manufacturers. All samples of the bulk CI were found to contain primarily amorphous cellulose (60% to 65%) with a smaller crystalline component (35% to 40%). The crystalline phase was primarily native cellulose (75% to 85%) with a minor amount of cellulose nitrate (15% to 25%). Elemental analyses of acid digests of CI materials indicated that the major components (>0.1% by weight) included aluminum, boron, calcium, sodium, and sulfur. An acid-insoluble residue present in all four materials (3% to 5% of original sample weight) was found to consist primarily of aluminum silicate hydroxide (kaolinite; approximately 85%) with minor amounts (<5% each) of magnesium silicate hydroxide (talc), potassium aluminum silicate hydroxide (muscovite), and titanium oxide (rutile). Solvent extracts of the bulk materials were analyzed for organic components by gas chromatography with flame ionization detection. Analyses revealed a mass of poorly resolved peaks. Because of the very low concentrations, further quantitative and qualitative analyses were not performed. An aerosol generation system was designed to separate CI particles based upon aerodynamic size and to simulate the process used during CI installation at work sites. Less than 0.1% of each of the CI samples was collected as the small respirable particle fraction. The mean equivalent diameter of respirable particles ranged from 0.6 to 0.7 mum. The numbers of fibers in the respirable fractions ranged from 9.7 x 103 to 1.4 x 106 fibers/g of CI. The respirable particle fractions did not contain cellulose material and consisted mainly of fire retardants and small quantities of clays. The respirable fraction from one CI sample was administered by intratracheal instillation to male Fischer 344 rats at doses of 0, 0.625, 1.25, 2.5, 5, or 10 mg/kg body weight; the bronchoalveolar lavage (BAL) fluid cellularity was evaluated 3 days later. Based upon the relatively mild severity of the inflammatory response, a dose of 5 mg/kg body weight was selected for use in a subsequent 28-day study. Rats received CI, titanium dioxide (particle controls), or sterile saline (controls). BAL fluid was evaluated 1, 3, 7, 14, and 28 days after instillation, and lung histopathology was evaluated 14 and 28 days after treatment. CI caused a greater influx of inflammatory cells than titanium dioxide and caused significant increases in BAL fluid protein and lactate dehydrogenase. These CI-induced changes in BAL fluid parameters were transient and by day 14 were not significantly different than those observed in rats treated with titanium dioxide or phosphate-buffered saline. Unlike titanium dioxide, CI treatment caused a minimal to mild nonprogressive, minimally fibrosing granulomatous pneumonitis characterized by nodular foci of macrophages and giant cells. These results indicated that few respirable particles or fibers are likely generated during the CI application and that the acute pulmonary toxicity is minimal. The CI exposure assessment was conducted with 10 contractors located across the United States. Air samples of total dust and respirable dust were collected for scanning electron microscopy (SEM) to characterize any fibers in the dust. Two SEM air samples for each day of CI activities were collected from the installer and hopper operator. Bulk CI samples were collected and analyzed for metal, boron, and sulfate content. Real-time and video exposure monitoring was conducted to further characterize the CI dust and workers' exposures. The exposure assessment also included a medical component. Investigators collected 175 personal breathing zone (PBZ) total dust, 106 area total dust, and 90 area respirable dust air samples during CI-related activities at the 10 contractor sites. Twenty-six employees' total dust 8-hour time-weighted averages (TWAs) exceeded the Occupational Safety and Health Administration (OSHA) permissible exposure limit (PEL) of 15 mg/m3, and 42 exceeded the American Conference of Governmental Industrial Hygienists (ACGIH) threshold-limit value (TLV) of 10 mg/m3. Respirable dust air sampling and real-time monitoring with particle size discrimination indicated low levels of respirable dust generation. The SEM analyses revealed that fibers were an average 28 mum in length and ranged from 5 mum to 150 mum. CI installers' PBZ total dust, area total dust, and area respirable dust air samples were all significantly higher during dry attic applications than wet attic applications (P<0.01). Conversely, the hopper operators' total dust exposures were significantly higher during wet wall and ceiling applications than dry wall and ceiling applications (P=0.02). Analyses of variance tests revealed that exposure concentrations in total dust air samples collected in the PBZ of all CI workers, including installers working in attics, installers during wall applications, hopper operators during attic applications, and hopper operators during wall and ceiling applications, varied significantly during dry applications (P<0.01). The respirable dust air samples collected in attic areas, hopper areas during attic applications, and hopper areas during wall and ceiling applications also differed significantly during dry applications (P=0.03). Twenty-three workers participated in the medical phase of the investigation. The workers completed medical and work history questionnaires, performed serial peak flow tests, and completed multiple acute symptom surveys. The medical questionnaires indicated respiratory, nasal, and skin symptoms that employees attributed to CI exposure. The most common symptoms reported while working with CI included nasal symptoms (35%), eye symptoms (35%), and morning phlegm production (25%). There was a temporal association between CI exposure and eye symptoms, but there was little evidence of lower respiratory system health conditions associated with CI exposure. Chemical analyses of the four bulk CI samples revealed only minor differences in additives. The major elemental components detected were aluminum, boron, calcium, sodium, and sulfur, but they were attributed to the fire retardants aluminum sulfate, boric acid, and sodium sulfate. For all four CI samples, less than 0.1% by weight was collected as the small respirable particle fraction. The fractions consisted mainly of fire retardants and smaller quantities of clays and did not contain cellulose material. Intratracheal instillation of the respirable fraction in rats produced minimal to mild inflammatory responses in the lungs with no increase in severity by 28 days after dosage. Although a significant increase in lung collagen was detected at day 28 in treated rats, microscopic evaluation revealed only a minimal to mild increase in collagen fibrils associated with granulomatous nodules. The results of these studies indicated that few respirable particles or fibers are generated during the aerosolization of CI, and that even at very high doses of respirable CI particles, acute pulmonary toxicity is minimal. These results are supported by the NIOSH workplace exposure assessment conducted on CI workers. Based on the air sample data collected from the 10 contractor site visits, there is a potential for overexposure to CI; however, respirable dust concentrations were typically low. There was increased potential for 8-hour TWAs exceeding the OSHA PEL for total and respirable dust when employees were involved in CI application activities for longer periods of time. There was evidence of work-related eye and mucous membrane irritation among some workers, which were possibly caused by the additives present in CI, such as boric acid. There was little evidence of lower respiratory system health conditions associated with CI exposure. Based upon the results of the CI chemical characterization studies, the pulmonary toxicity study, and the worksite exposure assessment, the NTP concluded that additional studies of CI in laboratory animals are not warranted at this time. However, the animal pulmonary toxicity studies and worker health surveys focused on acute CI exposures and do not preclude the possibility of toxicity resulting from chronic exposure. Although exposure concentrations of respirable CI particulate matter were low, additional information is needed on the biodurability and reactivity of CI particles and fibers in the respiratory tract. CI should continue to be regarded as a nuisance dust, and workers should continue to wear protective masks to prevent inhalation exposure to CI dusts.

Dynamic modeling and control of a solid-sorbent CO{sub 2} capture process with two-stage bubbling fluidized bed adsorber reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Modekurti, S.; Bhattacharyya, D.; Zitney, S.

2012-01-01

Solid-sorbent-based CO{sub 2} capture processes have strong potential for reducing the overall energy penalty for post-combustion capture from the flue gas of a conventional pulverized coal power plant. However, the commercial success of this technology is contingent upon it operating over a wide range of capture rates, transient events, malfunctions, and disturbances, as well as under uncertainties. To study these operational aspects, a dynamic model of a solid-sorbent-based CO{sub 2} capture process has been developed. In this work, a one-dimensional (1D), non-isothermal, dynamic model of a two-stage bubbling fluidized bed (BFB) adsorber-reactor system with overflow-type weir configuration has been developedmore » in Aspen Custom Modeler (ACM). The physical and chemical properties of the sorbent used in this study are based on a sorbent (32D) developed at National Energy Technology Laboratory (NETL). Each BFB is divided into bubble, emulsion, and cloud-wake regions with the assumptions that the bubble region is free of solids while both gas and solid phases coexist in the emulsion and cloud-wake regions. The BFB dynamic model includes 1D partial differential equations (PDEs) for mass and energy balances, along with comprehensive reaction kinetics. In addition to the two BFB models, the adsorber-reactor system includes 1D PDE-based dynamic models of the downcomer and outlet hopper, as well as models of distributors, control valves, and other pressure-drop devices. Consistent boundary and initial conditions are considered for simulating the dynamic model. Equipment items are sized and appropriate heat transfer options, wherever needed, are provided. Finally, a valid pressure-flow network is developed and a lower-level control system is designed. Using ACM, the transient responses of various process variables such as flue gas and sorbent temperatures, overall CO{sub 2} capture, level of solids in the downcomer and hopper have been studied by simulating typical disturbances such as change in the temperature, flowrate, and composition of the flue gas. To maintain the overall CO{sub 2} capture at a desired level in face of the typical disturbances, two control strategies were considered–a proportional-integral-derivative (PID)-based feedback control strategy and a feedforward-augmented feedback control strategy. Dynamic simulation results show that both the strategies result in unacceptable overshoot/undershoot and a long settling time. To improve the control system performance, a linear model predictive controller (LMPC) is designed. In summary, the overall results illustrate how optimizing the operation and control of carbon capture systems can have a significant impact on the extent and the rate at which commercial-scale capture processes will be scaled-up, deployed, and used in the years to come.« less

Environmental impacts of different crop rotations in terms of soil compaction.

PubMed

Götze, Philipp; Rücknagel, Jan; Jacobs, Anna; Märländer, Bernward; Koch, Heinz-Josef; Christen, Olaf

2016-10-01

Avoiding soil compaction caused by agricultural management is a key aim of sustainable land management, and the soil compaction risk should be considered when assessing the environmental impacts of land use systems. Therefore this project compares different crop rotations in terms of soil structure and the soil compaction risk. It is based on a field trial in Germany, in which the crop rotations (i) silage maize (SM) monoculture, (ii) catch crop mustard (Mu)_sugar beet (SB)-winter wheat (WW)-WW, (iii) Mu_SM-WW-WW and (iv) SB-WW-Mu_SM are established since 2010. Based on the cultivation dates, the operation specific soil compaction risks and the soil compaction risk of the entire crop rotations are modelled at two soil depths (20 and 35 cm). To this end, based on assumptions of the equipment currently used in practice by a model farm, two scenarios are modelled (100 and 50% hopper load for SB and WW harvest). In addition, after one complete rotation, in 2013 and in 2014, the physical soil parameters saturated hydraulic conductivity (kS) and air capacity (AC) were determined at soil depths 2-8, 12-18, 22-28 and 32-38 cm in order to quantify the soil structure. At both soil depths, the modelled soil compaction risks for the crop rotations including SB (Mu_SB-WW-WW, SB-WW-Mu_SM) are higher (20 cm: medium to very high risks; 35 cm: no to medium risks) than for those without SB (SM monoculture, Mu_SM-WW-WW; 20 cm: medium risks; 35 cm: no to low risks). This increased soil compaction risk is largely influenced by the SB harvest in years where soil water content is high. Halving the hopper load and adjusting the tyre inflation pressure reduces the soil compaction risk for the crop rotation as a whole. Under these conditions, there are no to low soil compaction risks for all variants in the subsoil (soil depth 35 cm). Soil structure is mainly influenced in the topsoil (2-8 cm) related to the cultivation of Mu as a catch crop and WW as a preceding crop. Concerning kS, Mu_SB-WW-WW (240 cm d(-1)) and Mu_SM-WW-WW (196 cm d(-1)) displayed significantly higher values than the SM monoculture (67 cm d(-1)), indicating better structural stability and infiltration capacity. At other soil depths, and for the parameter AC, there are no systematic differences in soil structure between the variants. Under the circumstances described, all crop rotations investigated are not associated with environmental impacts caused by soil compaction. Copyright © 2016 Elsevier Ltd. All rights reserved.

Mitochondrial Genome Analysis of Wild Rice (Oryza minuta) and Its Comparison with Other Related Species.

PubMed

Asaf, Sajjad; Khan, Abdul Latif; Khan, Abdur Rahim; Waqas, Muhammad; Kang, Sang-Mo; Khan, Muhammad Aaqil; Shahzad, Raheem; Seo, Chang-Woo; Shin, Jae-Ho; Lee, In-Jung

2016-01-01

Oryza minuta (Poaceae family) is a tetraploid wild relative of cultivated rice with a BBCC genome. O. minuta has the potential to resist against various pathogenic diseases such as bacterial blight (BB), white backed planthopper (WBPH) and brown plant hopper (BPH). Here, we sequenced and annotated the complete mitochondrial genome of O. minuta. The mtDNA genome is 515,022 bp, containing 60 protein coding genes, 31 tRNA genes and two rRNA genes. The mitochondrial genome organization and the gene content at the nucleotide level are highly similar (89%) to that of O. rufipogon. Comparison with other related species revealed that most of the genes with known function are conserved among the Poaceae members. Similarly, O. minuta mt genome shared 24 protein-coding genes, 15 tRNA genes and 1 ribosomal RNA gene with other rice species (indica and japonica). The evolutionary relationship and phylogenetic analysis revealed that O. minuta is more closely related to O. rufipogon than to any other related species. Such studies are essential to understand the evolutionary divergence among species and analyze common gene pools to combat risks in the current scenario of a changing environment.

On-sun testing of an advanced falling particle receiver system

NASA Astrophysics Data System (ADS)

Ho, Clifford K.; Christian, Joshua M.; Yellowhair, Julius; Siegel, Nathan; Jeter, Sheldon; Golob, Matthew; Abdel-Khalik, Said I.; Nguyen, Clayton; Al-Ansary, Hany

2016-05-01

A 1 MWth high-temperature falling particle receiver was constructed and tested at the National Solar Thermal Test Facility at Sandia National Laboratories. The continuously recirculating system included a particle elevator, top and bottom hoppers, and a cavity receiver that comprised a staggered array of porous chevron-shaped mesh structures that slowed the particle flow through the concentrated solar flux. Initial tests were performed with a peak irradiance of ~300 kW/m2 and a particle mass flow rate of 3.3 kg/s. Peak particle temperatures reached over 700 °C near the center of the receiver, but the particle temperature increase near the sides was lower due to a non-uniform irradiance distribution. At a particle inlet temperature of ~440 °C, the particle temperature increase was 27 °C per meter of drop length, and the thermal efficiency was ~60% for an average irradiance of 110 kW/m2. At an average irradiance of 211 kW/m2, the particle temperature increase was 57.1 °C per meter of drop length, and the thermal efficiency was ~65%. Tests with higher irradiances are being performed and are expected to yield greater particle temperature increases and efficiencies.

A prototype splitter apparatus for dividing large catches of small fish

USGS Publications Warehouse

Stapanian, Martin A.; Edwards, William H.

2012-01-01

Due to financial and time constraints, it is often necessary in fisheries studies to divide large samples of fish and estimate total catch from the subsample. The subsampling procedure may involve potential human biases or may be difficult to perform in rough conditions. We present a prototype gravity-fed splitter apparatus for dividing large samples of small fish (30–100 mm TL). The apparatus features a tapered hopper with a sliding and removable shutter. The apparatus provides a comparatively stable platform for objectively obtaining subsamples, and it can be modified to accommodate different sizes of fish and different sample volumes. The apparatus is easy to build, inexpensive, and convenient to use in the field. To illustrate the performance of the apparatus, we divided three samples (total N = 2,000 fish) composed of four fish species. Our results indicated no significant bias in estimating either the number or proportion of each species from the subsample. Use of this apparatus or a similar apparatus can help to standardize subsampling procedures in large surveys of fish. The apparatus could be used for other applications that require dividing a large amount of material into one or more smaller subsamples.

A new data-processing approach to study particle motion using ultrafast X-ray tomography scanner: case study of gravitational mass flow

NASA Astrophysics Data System (ADS)

Waktola, Selam; Bieberle, Andre; Barthel, Frank; Bieberle, Martina; Hampel, Uwe; Grudzień, Krzysztof; Babout, Laurent

2018-04-01

In most industrial products, granular materials are often required to flow under gravity in various kinds of silo shapes and usually through an outlet in the bottom. There are several interrelated parameters which affect the flow, such as internal friction, bulk and packing density, hopper geometry, and material type. Due to the low-spatial resolution of electrical capacitance tomography or scanning speed limitation of standard X-ray CT systems, it is extremely challenging to measure the flow velocity and possible centrifugal effects of granular materials flow effectively. However, ROFEX (ROssendorf Fast Electron beam X-ray tomography) opens new avenues of granular flow investigation due to its very high temporal resolution. This paper aims to track particle movements and evaluate the local grain velocity during silo discharging process in the case of mass flow. The study has considered the use of the Seramis material, which can also serve as a type of tracer particles after impregnation, due to its porous nature. The presented novel image processing and analysis approach allows satisfyingly measuring individual particle velocities but also tracking their lateral movement and three-dimensional rotations.

Preliminary research on flow rate and free surface of the accelerator driven subcritical system gravity-driven dense granular-flow target

PubMed Central

Li, Xiaodong; Wan, Jiangfeng; Zhang, Sheng; Lin, Ping; Zhang, Yanshi; Yang, Guanghui; Wang, Mengke; Duan, Wenshan; Sun, Jian’an

2017-01-01

A spallation target is one of the three core parts of the accelerator driven subcritical system (ADS), which has already been investigated for decades. Recently, a gravity-driven Dense Granular-flow Target (DGT) is proposed, which consists of a cylindrical hopper and an internal coaxial cylindrical beam pipe. The research on the flow rate and free surface are important for the design of the target whether in Heavy Liquid Metal (HLM) targets or the DGT. In this paper, the relations of flow rate and the geometry of the DGT are investigated. Simulations based on the discrete element method (DEM) implementing on Graphics Processing Units (GPUs) and experiments are both performed. It is found that the existence of an internal pipe doesn’t influence the flow rate when the distance from the bottom of the pipe to orifice is large enough even in a larger system. Meanwhile, snapshots of the free surface formed just below the beam pipe are given. It is observed that the free surface is stable over time. The entire research is meaningful for the design of DGT. PMID:29095910

Compression device for feeding a waste material to a reactor

DOEpatents

Williams, Paul M.; Faller, Kenneth M.; Bauer, Edward J.

2001-08-21

A compression device for feeding a waste material to a reactor includes a waste material feed assembly having a hopper, a supply tube and a compression tube. Each of the supply and compression tubes includes feed-inlet and feed-outlet ends. A feed-discharge valve assembly is located between the feed-outlet end of the compression tube and the reactor. A feed auger-screw extends axially in the supply tube between the feed-inlet and feed-outlet ends thereof. A compression auger-screw extends axially in the compression tube between the feed-inlet and feed-outlet ends thereof. The compression tube is sloped downwardly towards the reactor to drain fluid from the waste material to the reactor and is oriented at generally right angle to the supply tube such that the feed-outlet end of the supply tube is adjacent to the feed-inlet end of the compression tube. A programmable logic controller is provided for controlling the rotational speed of the feed and compression auger-screws for selectively varying the compression of the waste material and for overcoming jamming conditions within either the supply tube or the compression tube.

Unitary plate electrode

NASA Technical Reports Server (NTRS)

Rowlette, John J. (Inventor); Clough, Thomas J. (Inventor); Josefowicz, Jack Y. (Inventor); Sibert, John W. (Inventor)

1985-01-01

The unitary electrode (10) comprises a porous sheet (12) of fiberglass the strands (14) of which contain a coating (16) of conductive tin oxide. The lower portion of the sheet contains a layer (18) of resin and the upper layer (20) contains lead dioxide forming a positive active electrode on an electrolyte-impervious layer. The strands (14) form a continuous conduction path through both layers (16, 18). Tin oxide is prevented from reduction by coating the surface of the plate facing the negative electrode with a conductive, impervious layer resistant to reduction such as a thin film (130) of lead or graphite filled resin adhered to the plate with a layer (31) of conductive adhesive. The plate (10) can be formed by casting a molten resin from kettle (60) onto a sheet of glass wool (56) overlying a sheet of lead foil and then applying positive active paste from hopper (64) into the upper layer (68). The plate can also be formed by passing an assembly of a sheet ( 80) of resin, a sheet (86) of sintered glass and a sheet (90) of lead between the nip (92) of heated rollers (93, 95) and then filling lead oxide into the pores (116) of the upper layer (118).

Carbohydrate-rich foods: glycaemic indices and the effect of constituent macronutrients.

PubMed

Widanagamage, Rahal D; Ekanayake, Sagarika; Welihinda, Jayantha

2009-01-01

The glycaemic index (GI) ranks foods according to their acute glycaemic impact and is used in planning meals for patients invoking glycaemic control through diet. Kurakkan (Eleusine coracana) flour roti, rice flour roti, atta flour roti, boiled breadfruit (Artocarpus altilis/Artocarpus communis) and boiled legumes (mungbean, cowpea and chickpea) were categorized as low-GI foods (relative to white bread; Prima Crust Top), and the corresponding GI (+/- standard error of the mean) values were 70+/-8, 69+/-7, 67+/-9, 64+/-7, 57+/-6, 49+/-8 and 29+/-5, respectively. Kurakkan flour pittu and wheat flour roti were classified as medium-GI foods with GI values of 85+/-6 and 72+/-6. Hoppers, rice flour pittu, wheat flour pittu and Olu-milk rice (seeds of Nymphaea lotus) were categorized as high-GI foods, and the corresponding GI (+/- standard error of the mean) values were 120+/-8, 103+/-7, 101+/-8 and 91+/-8, respectively. The GI values significantly (P<0.01) and negatively correlated with the insoluble dietary fibre (rho = - 0.780), soluble dietary fibre (rho = - 0.712) and protein (rho = - 0.738) contents in grams per 100 g digestible starch containing foods.

Sweet Poisons: Honeys Contaminated with Glycosides of the Neurotoxin Tutin.

PubMed

Larsen, Lesley; Joyce, Nigel I; Sansom, Catherine E; Cooney, Janine M; Jensen, Dwayne J; Perry, Nigel B

2015-06-26

Poisonings due to consumption of honeys containing plant toxins have been reported widely. One cause is the neurotoxin tutin, an oxygenated sesquiterpene picrotoxane, traced back to honeybees (Apis mellifera) collecting honeydew produced by passionvine hoppers (Scolypopa australis) feeding on sap of the poisonous shrub tutu (Coriaria spp.). However, a pharmacokinetic study suggested that unidentified conjugates of tutin were also present in such honeys. We now report the discovery, using ion trap LC-MS, of two tutin glycosides and their purification and structure determination as 2-(β-d-glucopyranosyl)tutin (4) and 2-[6'-(α-d-glucopyranosyl)-β-d-glucopyranosyl]tutin (5). These compounds were used to develop a quantitative triple quadrupole LC-MS method for honey analysis, which showed the presence of tutin (3.6 ± 0.1 μg/g honey), hyenanchin (19.3 ± 0.5), tutin glycoside (4) (4.9 ± 0.4), and tutin diglycoside (5) (4.9 ± 0.1) in one toxic honey. The ratios of 4 and 5 to tutin varied widely in other tutin-containing honeys. The glycosidation of tutin may represent detoxification by one or both of the insects involved in the food chain from plant to honey.

Factors that influence the efficiency of a fluidized-bed-type tribo-electrostatic separator for mixed granular plastics

NASA Astrophysics Data System (ADS)

Dascalescu, L.; Fati, O.; Bilici, M.; Rahou, F.; Dragan, C.; Samuila, A.; Iuga, A.

2011-06-01

Fluidized bed devices have already been used as tribochargers for various industrial electrostatic separation processes. In the present paper, the authors investigate the behaviour of polyamide - polycarbonate granular plastic mixtures in a parallelepiped bed, the height of which is roughly 2 times its length or width, so that the collisions between granules become the prevailing tribocharging mechanism. Two of the opposite walls of the tribocharging chamber consist of metallic plates connected to two DC high-voltage supplies of opposite polarities, so that the charged particles are attracted to the electrodes and separated while still in the fluidized state. The collecting hoppers are designed as Faraday cups connected to two electrometers, thus allowing the instantaneous measurement of the charge carried by the separated particles. Experimental design methodology was employed for the optimization of the tribo-aero-electrostatic separation process, the input variables being the high-voltage applied to the electrodes and the duration of the tribocharging. Higher voltages applied to the electrode system do not necessarily lead to larger quantities of collected products but improve the purity of the concentrates. The composition of the mixture influences the outcome of the process.

Phased-array ultrasonic surface contour mapping system and method for solids hoppers and the like

DOEpatents

Fasching, George E.; Smith, Jr., Nelson S.

1994-01-01

A real time ultrasonic surface contour mapping system is provided including a digitally controlled phased-array of transmitter/receiver (T/R) elements located in a fixed position above the surface to be mapped. The surface is divided into a predetermined number of pixels which are separately scanned by an arrangement of T/R elements by applying phase delayed signals thereto that produce ultrasonic tone bursts from each T/R that arrive at a point X in phase and at the same time relative to the leading edge of the tone burst pulse so that the acoustic energies from each T/R combine in a reinforcing manner at point X. The signals produced by the reception of the echo signals reflected from point X back to the T/Rs are also delayed appropriately so that they add in phase at the input of a signal combiner. This combined signal is then processed to determine the range to the point X using density-corrected sound velocity values. An autofocusing signal is developed from the computed average range for a complete scan of the surface pixels. A surface contour map is generated in real time form the range signals on a video monitor.

Screening for Learning and Memory Mutations: A New Approach

PubMed Central

Gallistel, C. R.; King, A. P.; Daniel, A. M.; Freestone, D.; Papachristos, E. B.; Balci, F.; Kheifets, A.; Zhang, J.; Su, X.; Schiff, G.; Kourtev, H.

2010-01-01

We describe a fully automated, live-in 24/7 test environment, with experimental protocols that measure the accuracy and precision with which mice match the ratio of their expected visit durations to the ratio of the incomes obtained from two hoppers, the progress of instrumental and classical conditioning (trials-to-acquisition), the accuracy and precision of interval timing, the effect of relative probability on the choice of a timed departure target, and the accuracy and precision of memory for the times of day at which food is available. The system is compact; it obviates the handling of the mice during testing; it requires negligible amounts of experimenter/technician time; and it delivers clear and extensive results from 3 protocols within a total of 7–9 days after the mice are placed in the test environment. Only a single 24-hour period is required for the completion of first protocol (the matching protocol), which is strong test of temporal and spatial estimation and memory mechanisms. Thus, the system permits the extensive screening of many mice in a short period of time and in limited space. The software is publicly available. PMID:20352069

Preliminary research on flow rate and free surface of the accelerator driven subcritical system gravity-driven dense granular-flow target.

PubMed

Li, Xiaodong; Wan, Jiangfeng; Zhang, Sheng; Lin, Ping; Zhang, Yanshi; Yang, Guanghui; Wang, Mengke; Duan, Wenshan; Sun, Jian'an; Yang, Lei

2017-01-01

A spallation target is one of the three core parts of the accelerator driven subcritical system (ADS), which has already been investigated for decades. Recently, a gravity-driven Dense Granular-flow Target (DGT) is proposed, which consists of a cylindrical hopper and an internal coaxial cylindrical beam pipe. The research on the flow rate and free surface are important for the design of the target whether in Heavy Liquid Metal (HLM) targets or the DGT. In this paper, the relations of flow rate and the geometry of the DGT are investigated. Simulations based on the discrete element method (DEM) implementing on Graphics Processing Units (GPUs) and experiments are both performed. It is found that the existence of an internal pipe doesn't influence the flow rate when the distance from the bottom of the pipe to orifice is large enough even in a larger system. Meanwhile, snapshots of the free surface formed just below the beam pipe are given. It is observed that the free surface is stable over time. The entire research is meaningful for the design of DGT.

Conceptual Design of Fertilizer Applicator for Oil Palm on Terrace Cultivation

NASA Astrophysics Data System (ADS)

Hermawan, W.

2018-05-01

The mechanical application of fertilizer for oil palm planted on terraces is still constrained by the narrow path which is difficult to pass by a power spreader. The objective of this research was to develop a conceptual design of fertilizer applicator for oil palm planted on terraces. The design requirements were developed based on a) terrace and track conditions, b) fertilizers and fertilization conditions, c) available prime movers, and d) user needs. Five design concepts were obtained: 1) an applicator with left and right arms to distribute the fertilizer, 2) an all-terrain vehicle equipped with a manually operated fertilizer injector, 3) an applicator equipped with a hole digger, 4) an applicator equipped with a shovel, and 5) an applicator equipped with a rotary tiller. The concepts were evaluated and compared with the current power spreader. The evaluation results showed that the applicator equipped with a rotary tiller had the most advantages on the expected criteria. The final design concept uses a 110 cm wide mini crawler tractor as the prime mover and is equipped with a hopper and a spinner disk for metering and conveying the fertilizer, and a 20 cm wide rotary tiller in the front of the machine.

Pyramided rice lines harbouring Allium sativum (asal) and Galanthus nivalis (gna) lectin genes impart enhanced resistance against major sap-sucking pests.

PubMed

Bharathi, Y; Vijaya Kumar, S; Pasalu, I C; Balachandran, S M; Reddy, V D; Rao, K V

2011-03-20

We have developed transgene pyramided rice lines, endowed with enhanced resistance to major sap-sucking insects, through sexual crosses made between two stable transgenic rice lines containing Allium sativum (asal) and Galanthus nivalis (gna) lectin genes. Presence and expression of asal and gna genes in pyramided lines were confirmed by PCR and western blot analyses. Segregation analysis of F₂ progenies disclosed digenic (9:3:3:1) inheritance of the transgenes. Homozygous F₃ plants carrying asal and gna genes were identified employing genetic and molecular methods besides insect bioassays. Pyramided lines, infested with brown planthopper (BPH), green leafhopper (GLH) and whitebacked planthopper (WBPH), proved more effective in reducing insect survival, fecundity, feeding ability besides delayed development of insects as compared to the parental transgenics. Under infested conditions, pyramided lines were found superior to the parental transgenics in their seed yield potential. This study represents first report on pyramiding of two lectin genes into rice exhibiting enhanced resistance against major sucking pests. The pyramided lines appear promising and might serve as a novel genetic resource in rice breeding aimed at durable and broad based resistance against hoppers. Copyright © 2011 Elsevier B.V. All rights reserved.

Hygiene at winter bird feeders in a southwestern Ontario city.

PubMed Central

Prescott, J F; Hunter, D B; Campbell, G D

2000-01-01

To further understand the source of the epidemic of salmonellosis in some species of birds using bird feeders in southern Ontario in the winter of 1997-1998, 124 bird feeder stations were examined for their state of hygiene and for Salmonella on 5 occasions during the winter of 1999 in a city of 100,000 people in southwestern Ontario. No Salmonella were isolated from feed contaminated with feces recovered from the feeders. Squirrel-proof feeders were significantly less contaminated with feces than were other feeder types (hopper, platform, silo), which did not differ significantly in their hygiene scores. Contamination of squirrel-proof feeders increased significantly through the course of the study, but other feeder types showed no significant change. Hygiene was poorer if feeders were maintained equally by both male and female household members, particularly as they grew older, but no age or gender effect was observed if only one person was largely responsible for maintaining the feeders. We concluded that winter bird feeder stations in a southern Ontario city were not contaminated with Salmonella but that bird feeder stations could be designed better to reduce fecal contamination of feed. PMID:10992987

Numerical investigations on flow dynamics of prismatic granular materials using the discrete element method

NASA Astrophysics Data System (ADS)

Hancock, W.; Weatherley, D.; Wruck, B.; Chitombo, G. P.

2012-04-01

The flow dynamics of granular materials is of broad interest in both the geosciences (e.g. landslides, fault zone evolution, and brecchia pipe formation) and many engineering disciplines (e.g chemical engineering, food sciences, pharmaceuticals and materials science). At the interface between natural and human-induced granular media flow, current underground mass-mining methods are trending towards the induced failure and subsequent gravitational flow of large volumes of broken rock, a method known as cave mining. Cave mining relies upon the undercutting of a large ore body, inducement of fragmentation of the rock and subsequent extraction of ore from below, via hopper-like outlets. Design of such mines currently relies upon a simplified kinematic theory of granular flow in hoppers, known as the ellipsoid theory of mass movement. This theory assumes that the zone of moving material grows as an ellipsoid above the outlet of the silo. The boundary of the movement zone is a shear band and internal to the movement zone, the granular material is assumed to have a uniformly high bulk porosity compared with surrounding stagnant regions. There is however, increasing anecdotal evidence and field measurements suggesting this theory fails to capture the full complexity of granular material flow within cave mines. Given the practical challenges obstructing direct measurement of movement both in laboratory experiments and in-situ, the Discrete Element Method (DEM [1]) is a popular alternative to investigate granular media flow. Small-scale DEM studies (c.f. [3] and references therein) have confirmed that movement within DEM silo flow models matches that predicted by ellipsoid theory, at least for mono-disperse granular material freely outflowing at a constant rate. A major draw-back of these small-scale DEM studies is that the initial bulk porosity of the simulated granular material is significantly higher than that of broken, prismatic rock. In this investigation, more realistic granular material geometries are simulated using the ESyS-Particle [2] DEM simulation software on cluster supercomputers. Individual grains of the granular material are represented as convex polyhedra. Initially the polyhedra are packed in a low bulk porosity configuration prior to commencing silo flow simulations. The resultant flow dynamics are markedly different to that predicted by ellipsoid theory. Initially shearing occurs around the silo outlet however rapidly shear localization in a particular direction dominates other directions, causing preferential movement in that direction. Within the shear band itself, the granular material becomes hgihly dilated however elsewhere the bulk porosity remains low. The low porosity within these regions promotes entrainment whereby large volumes of granular material interlock and begin to rotate and translate as a single rigid body. In some cases, entrainment may result in complete overturning of a large volume of material. The consequences of preferential shear localization and in particular, entrainment, for granular media flow in cave mines and natural settings (such as brecchia pipes) is a topic of ongoing research to be presented at the meeting.

Realizing life-scalable experimental pyroclastic density currents

NASA Astrophysics Data System (ADS)

Cronin, S. J.; Lube, G.; Breard, E.; Jones, J.; Valentine, G.; Freundt, A.; Hort, M. K.; Bursik, M. I.

2013-12-01

Pyroclastic Density Currents (PDCs) - the most deadly threat from volcanoes - are extremely hot, ground-hugging currents of rock fragments and gas that descend slopes at hundreds of kilometers per hour. These hostile flows are impossible to internally measure, thus volcanologists are persistently blocked in efforts to realistically forecast their internal mechanics and hazards. Attempts to fill this gap via laboratory-scale experiments continue to prove difficult, because they usually mismatch the dynamic and kinematic scaling of real-world flows by several orders of magnitude. In a multi-institutional effort, the first large-scale pyroclastic flow generator that can synthesize repeatable hot high-energy gas-particle mixture flows in safety has been commissioned in New Zealand. The final apparatus stands 15 m high, consisting of a tower/elevator system; an instrumented hopper that can hold >6000 kg (or 3.2 m3) of natural volcanic materials, which can be discharged at a range of controlled rates onto an instrumented, variably inclinable (6-25°) glass-sided chute for examining the vertical profiles of PDCs in motion. The use of rhyolitic pyroclastic material from the 1800 AD Taupo Eruption (with its natural grain-size, sorting and shape characteristics) and gas ensures natural coupling between the solids and fluid phases. PDC analogues with runout of >15 meters and flow depths of 1.5-6 meters are created by generating variably heated falling columns of natural volcanic particles (50-1300 kg/s), dispersed and aerated to controlled particle densities between 3 and 60 vol.% at the base of the elevated hopper. The descending columns rapidly generate high-velocity flows (up to 14 m/s) once impacting on the inclined channel, reproducing many features of natural flows, including segregation into dense and dilute regimes, progressive aggradational and en masse deposition of particles and the development of high internal gas-pore-pressures during flow. The PDC starting conditions (velocity, mass flux, particle solids concentration and temperature) can be precisely varied to obtain a wide range of PDC gas-particle transport and sedimentation conditions that match dynamic and kinematic scaling of natural flows. For instance, bulk flow scaling shows full turbulence (Re>106); while at the same time, the variation in Stokes and Stability numbers (describing Lagrangian acceleration of particles due to gravity and viscous drag) cover a wide range of natural conditions. The resulting PDC flow regimes include convection dominated dilute suspension that produce lateral ash-cloud surges, inertial dry granular to partially fluidised flows with high dynamic pressures, and, intermittent flow regimes of intermediate particle solids concentration. Depending on the PDC starting conditions, stratified, dune-bedded or inversely graded bedforms are created, whose formation can be tracked using high-speed cinematography and particle-image-velocimetry. We present here the first overview results from these experiments and invite further multi-organisational collaboration in ongoing simulations.

Wear compensating seal means for rotary piston coal feeder

DOEpatents

Gencsoy, Hasan T.; Gardner, John F.

1979-01-01

The present invention is directed to a wear compensating seal arrangement for use in a rotary piston feeder utilized for feeding pulverized coal into a gasifier operating at relatively high pressures and elevated temperatures. The rotary piston feeder has a circular casing with a coal loading opening therein diametrically opposed from a coal discharge and contains a rotatable disoidal rotor having a cylinder in which a reciprocatable piston is disposed. The reciprocation of the piston within the cylinder is provided by a stationary conjugate cam whereby pulverized coal from a coal hopper at atmospheric pressure can be introduced into the cylinder and then discharged therefrom into the high pressure gasifier while maintaining minimal losses of producer gas and the expenditure of minimal energy which would detract from the efficiency of the gasification. The seal arrangement of the present invention is disposed between the rotor and the casing about the coal discharge and prevents the high pressure gases from within the gasifier from escaping between these relatively movable parts during operation of the coal feeder. The seal utilizes a primary seal in contact with the rotor and a secondary seal supporting the primary seal. The primary seal is continuously urged towards the rotor by springs and the high pressure producer gas.

Towards reproducible experimental studies for non-convex polyhedral shaped particles

NASA Astrophysics Data System (ADS)

Wilke, Daniel N.; Pizette, Patrick; Govender, Nicolin; Abriak, Nor-Edine

2017-06-01

The packing density and flat bottomed hopper discharge of non-convex polyhedral particles are investigated in a systematic experimental study. The motivation for this study is two-fold. Firstly, to establish an approach to deliver quality experimental particle packing data for non-convex polyhedral particles that can be used for characterization and validation purposes of discrete element codes. Secondly, to make the reproducibility of experimental setups as convenient and readily available as possible using affordable and accessible technology. The primary technology for this study is fused deposition modeling used to 3D print polylactic acid (PLA) particles using readily available 3D printer technology. A total of 8000 biodegradable particles were printed, 1000 white particles and 1000 black particles for each of the four particle types considered in this study. Reproducibility is one benefit of using fused deposition modeling to print particles, but an extremely important additional benefit is that specific particle properties can be explicitly controlled. As an example in this study the volume fraction of each particle can be controlled i.e. the effective particle density can be adjusted. In this study the particle volumes reduces drastically as the non-convexity is increased, however all printed white particles in this study have the same mass within 2% of each other.

Testing of commonly used mixing and sampling procedures to evaluate fertilizer blends prepared with matched and mismatched particle sizes.

PubMed

Hall, William L; Ramsey, Charles; Falls, J Harold

2014-01-01

Bulk blending of dry fertilizers is a common practice in the United States and around the world. This practice involves the mixing (either physically or volumetrically) of concentrated, high analysis raw materials. Blending is followed by bagging (for small volume application such as lawn and garden products), loading into truck transports, and spreading. The great majority of bulk blended products are not bagged but handled in bulk and transferred from the blender to a holding hopper. The product is then transferred to a transport vehicle, which may, or may not, also be a spreader. If the primary transport vehicle is not a spreader, then there is another transfer at the user site to a spreader for application. Segregation of materials that are mismatched due to size, density, or shape is an issue when attempting to effectively sample or evenly spread bulk blended products. This study, prepared in coordination with and supported by the Florida Department of Agriculture and Consumer Services and the Florida Fertilizer and Agrochemical Association, looks at the impact of varying particle size as it relates to blending, sampling, and application of bulk blends. The study addresses blends containing high ratios of N-P-K materials and varying (often small) quantities of the micronutrient Zn.

Enabling Efficient Climate Science Workflows in High Performance Computing Environments

NASA Astrophysics Data System (ADS)

Krishnan, H.; Byna, S.; Wehner, M. F.; Gu, J.; O'Brien, T. A.; Loring, B.; Stone, D. A.; Collins, W.; Prabhat, M.; Liu, Y.; Johnson, J. N.; Paciorek, C. J.

2015-12-01

A typical climate science workflow often involves a combination of acquisition of data, modeling, simulation, analysis, visualization, publishing, and storage of results. Each of these tasks provide a myriad of challenges when running on a high performance computing environment such as Hopper or Edison at NERSC. Hurdles such as data transfer and management, job scheduling, parallel analysis routines, and publication require a lot of forethought and planning to ensure that proper quality control mechanisms are in place. These steps require effectively utilizing a combination of well tested and newly developed functionality to move data, perform analysis, apply statistical routines, and finally, serve results and tools to the greater scientific community. As part of the CAlibrated and Systematic Characterization, Attribution and Detection of Extremes (CASCADE) project we highlight a stack of tools our team utilizes and has developed to ensure that large scale simulation and analysis work are commonplace and provide operations that assist in everything from generation/procurement of data (HTAR/Globus) to automating publication of results to portals like the Earth Systems Grid Federation (ESGF), all while executing everything in between in a scalable environment in a task parallel way (MPI). We highlight the use and benefit of these tools by showing several climate science analysis use cases they have been applied to.

Nickel-coated Aluminum Particles: A Promising Fuel for Mars Missions

NASA Technical Reports Server (NTRS)

Shafirovich, Evgeny; Varma, Arvind

2004-01-01

Combustion of metals in carbon dioxide is a promising source of energy for propulsion on Mars. This approach is based on the ability of some metals (e.g. Mg, Al) to burn in CO2 atmosphere and suggests use of the Martian carbon dioxide as an oxidizer in jet or rocket engines. Analysis shows that CO2/metal propulsion will reduce significantly the mass of propellant transported from Earth for long-range mobility on Mars and sample return missions. Recent calculations for the near-term missions indicate that a 200-kg ballistic hopper with CO2/metal rocket engines and a CO2 acquisition unit can perform 10-15 flights on Mars with the total range of 10-15 km, i.e. fulfill the exploration program typically assigned for a rover. Magnesium is currently recognized as a candidate fuel for such engines owing to easy ignition and fast burning in CO2. Aluminum may be more advantageous if a method for reducing its ignition temperature is found. Coating it by nickel is one such method. It is known that a thin nickel layer of nickel on the surface of aluminum particles can prevent their agglomeration and simultaneously facilitate their ignition, thus increasing the efficiency of aluminized propellants.

PIC simulations of the trapped electron filamentation instability in finite-width electron plasma waves

NASA Astrophysics Data System (ADS)

Winjum, B. J.; Banks, J. W.; Berger, R. L.; Cohen, B. I.; Chapman, T.; Hittinger, J. A. F.; Rozmus, W.; Strozzi, D. J.; Brunner, S.

2012-10-01

We present results on the kinetic filamentation of finite-width nonlinear electron plasma waves (EPW). Using 2D simulations with the PIC code BEPS, we excite a traveling EPW with a Gaussian transverse profile and a wavenumber k0λDe= 1/3. The transverse wavenumber spectrum broadens during transverse EPW localization for small width (but sufficiently large amplitude) waves, while the spectrum narrows to a dominant k as the initial EPW width increases to the plane-wave limit. For large EPW widths, filaments can grow and destroy the wave coherence before transverse localization destroys the wave; the filaments in turn evolve individually as self-focusing EPWs. Additionally, a transverse electric field develops that affects trapped electrons, and a beam-like distribution of untrapped electrons develops between filaments and on the sides of a localizing EPW. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344 and funded by the Laboratory Research and Development Program at LLNL under project tracking code 12-ERD-061. Supported also under Grants DE-FG52-09NA29552 and NSF-Phy-0904039. Simulations were performed on UCLA's Hoffman2 and NERSC's Hopper.

Using NERSC High-Performance Computing (HPC) systems for high-energy nuclear physics applications with ALICE

NASA Astrophysics Data System (ADS)

Fasel, Markus

2016-10-01

High-Performance Computing Systems are powerful tools tailored to support large- scale applications that rely on low-latency inter-process communications to run efficiently. By design, these systems often impose constraints on application workflows, such as limited external network connectivity and whole node scheduling, that make more general-purpose computing tasks, such as those commonly found in high-energy nuclear physics applications, more difficult to carry out. In this work, we present a tool designed to simplify access to such complicated environments by handling the common tasks of job submission, software management, and local data management, in a framework that is easily adaptable to the specific requirements of various computing systems. The tool, initially constructed to process stand-alone ALICE simulations for detector and software development, was successfully deployed on the NERSC computing systems, Carver, Hopper and Edison, and is being configured to provide access to the next generation NERSC system, Cori. In this report, we describe the tool and discuss our experience running ALICE applications on NERSC HPC systems. The discussion will include our initial benchmarks of Cori compared to other systems and our attempts to leverage the new capabilities offered with Cori to support data-intensive applications, with a future goal of full integration of such systems into ALICE grid operations.

Characterization of lunar ilmenite resources

NASA Astrophysics Data System (ADS)

Heiken, G. H.; Vaniman, D. T.

Ilmenite will be an important lunar resource, to be used mainly for oxygen production but also as a source of iron. Ilmenite abundances in high-Ti basaltic lavas are higher (9-19 vol pct) than in high-Ti mare soils (mostly less than 10 vol pct). This factor alone may make crushed high-Ti basaltic lavas most attractive as a target for ilmenite extraction. Concentration of ilmenite from either a crushed basalt or regolith requires size sorting to avoid polycrystalline fragments. In coarse-grained high-Ti basaltic lavas, about 60-80 percent of the ilmenite will consist of relatively 'clean' single crystals if the rocks are crushed to a size of 0.2 mm. Fine-grained high-Ti basalts, with thin skeletal or hopper-shaped ilmentes, would produce essentially no free or 'clean' ilmenite grains even if crushed to 0.15 mm and only about 7 percent free ilmenite if crushed to 0.05 mm. Data from the 2.8-m-thick regolith sampled by coring at the Apollo 17 site show that in even the most basalt-clast-rich and least mature stratigraphic intervals, free ilmenite grains make up less than 2 percent of the 0.02- to 0.2-mm size fraction and a mere 0.3 percent of the 0.2- to 2-mm size fraction.

Fractal aspects of the flow and shear behaviour of free-flowable particle size fractions of pharmaceutical directly compressible excipient sorbitol.

PubMed

Hurychová, Hana; Lebedová, Václava; Šklubalová, Zdenka; Dzámová, Pavlína; Svěrák, Tomáš; Stoniš, Jan

Flowability of powder excipients is directly influenced by their size and shape although the granulometric influence of the flow and shear behaviour of particulate matter is not studied frequently. In this work, the influence of particle size on the mass flow rate through the orifice of a conical hopper, and the cohesion and flow function was studied for four free-flowable size fractions of sorbitol for direct compression in the range of 0.080-0.400 mm. The particles were granulometricaly characterized using an optical microscopy; a boundary fractal dimension of 1.066 was estimated for regular sorbitol particles. In the particle size range studied, a non-linear relationship between the mean particle size and the mass flow rate Q10 (g/s) was detected having amaximum at the 0.245mm fraction. The best flow properties of this fraction were verified with aJenike shear tester due to the highest value of flow function and the lowest value of the cohesion. The results of this work show the importance of the right choice of the excipient particle size to achieve the best flow behaviour of particulate material.Key words: flowability size fraction sorbitol for direct compaction Jenike shear tester fractal dimension.

Experimental and computational investigation on the flow behavior of granular particles through an inclined rotating chute

NASA Astrophysics Data System (ADS)

Shirsath, Sushil; Padding, Johan; Clercx, Herman; Kuipers, Hans

2013-11-01

In blast furnaces operated in the steel industry, particles like coke, sinter and pellets enter from a hopper and are distributed on the burden surface by a rotating chute. Such particulate flows suffer occasionally from particle segregation in chute, which hinders efficient throughflow. To obtain a more fundamental insight into these effects, monodisperse particles flowing through a rotating chute inclined at a fixed angle has been studied both with experiments and with a discrete particle model. We observe that the prevailing flow patterns depend strongly on the rotation rate of the chute. With increasing rotation rate the particles are moving increasingly to the side wall. The streamwise particle velocity is slightly reduced in the first half length of the chute due to the Coriolis force, but strongly increased in the second half due to the centrifugal forces. The particle bed height becomes a two-dimensional function of the position inside the chute, with a strong increase in bed height along the sidewall due to the Coriolis forces. It was found that the DPM model was agreed well with the experimental measurements. We will also discuss ongoing work, where we investigate the effects of binary particle mixtures with different particle size or density, different chute geometry.

Chimpanzees, cooking, and a more comparative psychology.

PubMed

Beran, Michael J; Hopper, Lydia M; de Waal, Frans B M; Brosnan, Sarah F; Sayers, Ken

2016-06-01

A recent report suggested that chimpanzees demonstrate the cognitive capacities necessary to understand cooking (Warneken & Rosati, 2015). We offered alternative explanations and mechanisms that could account for the behavioral responses of those chimpanzees, and questioned the manner in which the data were used to examine human evolution (Beran, Hopper, de Waal, Sayers, & Brosnan, 2015). Two commentaries suggested either that we were overly critical of the original report's claims and methodology (Rosati & Warneken, 2016), or that, contrary to our statements, early biological thinkers contributed little to questions concerning the evolutionary importance of cooking (Wrangham, 2016). In addition, both commentaries took issue with our treatment of chimpanzee referential models in human evolutionary studies. Our response offers points of continued disagreement as well as points of conciliation. We view Warneken and Rosati's general conclusions as a case of affirming the consequent-a logical conundrum in which, in this case, a demonstration of a partial list of the underlying abilities required for a cognitive trait/suite (understanding of cooking) are suggested as evidence for that ability. And although we strongly concur with both Warneken and Rosati (2015) and Wrangham (2016) that chimpanzee research is invaluable and essential to understanding humanness, it can only achieve its potential via the holistic inclusion of all available evidence-including that from other animals, evolutionary theory, and the fossil and archaeological records.

LOGIC CIRCUIT

DOEpatents

Strong, G.H.; Faught, M.L.

1963-12-24

A device for safety rod counting in a nuclear reactor is described. A Wheatstone bridge circuit is adapted to prevent de-energizing the hopper coils of a ball backup system if safety rods, sufficient in total control effect, properly enter the reactor core to effect shut down. A plurality of resistances form one arm of the bridge, each resistance being associated with a particular safety rod and weighted in value according to the control effect of the particular safety rod. Switching means are used to switch each of the resistances in and out of the bridge circuit responsive to the presence of a particular safety rod in its effective position in the reactor core and responsive to the attainment of a predetermined velocity by a particular safety rod enroute to its effective position. The bridge is unbalanced in one direction during normal reactor operation prior to the generation of a scram signal and the switching means and resistances are adapted to unbalance the bridge in the opposite direction if the safety rods produce a predetermined amount of control effect in response to the scram signal. The bridge unbalance reversal is then utilized to prevent the actuation of the ball backup system, or, conversely, a failure of the safety rods to produce the predetermined effect produces no unbalance reversal and the ball backup system is actuated. (AEC)

Pebble Fuel Handling and Reactivity Control for Salt-Cooled High Temperature Reactors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peterson, Per; Greenspan, Ehud

2015-02-09

This report documents the work completed on the X-PREX facility under NEUP Project 11- 3172. This project seeks to demonstrate the viability of pebble fuel handling and reactivity control for fluoride salt-cooled high-temperature reactors (FHRs). The research results also improve the understanding of pebble motion in helium-cooled reactors, as well as the general, fundamental understanding of low-velocity granular flows. Successful use of pebble fuels in with salt coolants would bring major benefits for high-temperature reactor technology. Pebble fuels enable on-line refueling and operation with low excess reactivity, and thus simpler reactivity control and improved fuel utilization. If fixed fuel designsmore » are used, the power density of salt- cooled reactors is limited to 10 MW/m 3 to obtain adequate duration between refueling, but pebble fuels allow power densities in the range of 20 to 30 MW/m 3. This can be compared to the typical modular helium reactor power density of 5 MW/m3. Pebble fuels also permit radial zoning in annular cores and use of thorium or graphite pebble blankets to reduce neutron fluences to outer radial reflectors and increase total power production. Combined with high power conversion efficiency, compact low-pressure primary and containment systems, and unique safety characteristics including very large thermal margins (>500°C) to fuel damage during transients and accidents, salt-cooled pebble fuel cores offer the potential to meet the major goals of the Advanced Reactor Concepts Development program to provide electricity at lower cost than light water reactors with improved safety and system performance.This report presents the facility description, experimental results, and supporting simulation methods of the new X-Ray Pebble Recirculation Experiment (X-PREX), which is now operational and being used to collect data on the behavior of slow dense granular flows relevant to pebble bed reactor core designs. The X-PREX facility uses novel digital x-ray tomography methods to track both the translational and rotational motion of spherical pebbles, which provides unique experimental results that can be used to validate discrete element method (DEM) simulations of pebble motion. The validation effort supported by the X-PREX facility provides a means to build confidence in analysis of pebble bed configuration and residence time distributions that impact the neutronics, thermal hydraulics, and safety analysis of pebble bed reactor cores. Experimental and DEM simulation results are reported for silo drainage, a classical problem in the granular flow literature, at several hopper angles. These studies include conventional converging and novel diverging geometries that provide additional flexibility in the design of pebble bed reactor cores. Excellent agreement is found between the X-PREX experimental and DEM simulation results. This report also includes results for additional studies relevant to the design and analysis of pebble bed reactor cores including the study of forces on shut down blades inserted directly into a packed bed and pebble flow in a cylindrical hopper that is representative of a small test reactor.« less