21 CFR 172.876 - Castor oil.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Castor oil. 172.876 Section 172.876 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... Multipurpose Additives § 172.876 Castor oil. The food additive castor oil may be safely used in accordance with...

21 CFR 172.876 - Castor oil.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Castor oil. 172.876 Section 172.876 Food and Drugs... PERMITTED FOR DIRECT ADDITION TO FOOD FOR HUMAN CONSUMPTION Multipurpose Additives § 172.876 Castor oil. The food additive castor oil may be safely used in accordance with the following conditions: (a) The...

21 CFR 172.876 - Castor oil.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Castor oil. 172.876 Section 172.876 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... Multipurpose Additives § 172.876 Castor oil. The food additive castor oil may be safely used in accordance with...

ANALYSIS OF RICIN TOXIN PREPARATIONS FOR CARBOHYDRATE AND FATTY ACID ABUNDANCE AND ISOTOPE RATIO INFORMATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wunschel, David S.; Kreuzer-Martin, Helen W.; Antolick, Kathryn C.

2009-12-01

This report describes method development and preliminary evaluation for analyzing castor samples for signatures of purifying ricin. Ricin purification from the source castor seeds is essentially a problem of protein purification using common biochemical methods. Indications of protein purification will likely manifest themselves as removal of the non-protein fractions of the seed. Two major, non-protein, types of biochemical constituents in the seed are the castor oil and various carbohydrates. The oil comprises roughly half the seed weight while the carbohydrate component comprises roughly half of the remaining “mash” left after oil and hull removal. Different castor oil and carbohydrate componentsmore » can serve as indicators of specific toxin processing steps. Ricinoleic acid is a relatively unique fatty acid in nature and is the most abundant component of castor oil. The loss of ricinoleic acid indicates a step to remove oil from the seeds. The relative amounts of carbohydrates and carbohydrate-like compounds, including arabinose, xylose, myo-inositol fucose, rhamnose, glucosamine and mannose detected in the sample can also indicate specific processing steps. For instance, the differential loss of arabinose relative to mannose and N-acetyl glucosamine indicates enrichment for the protein fraction of the seed using protein precipitation. The methods developed in this project center on fatty acid and carbohydrate extraction from castor samples followed by derivatization to permit analysis by gas chromatography-mass spectrometry (GC-MS). Method descriptions herein include: the source and preparation of castor materials used for method evaluation, the equipment and description of procedure required for chemical derivatization, and the instrument parameters used in the analysis. Two types of derivatization methods describe analysis of carbohydrates and one procedure for analysis of fatty acids. Two types of GC-MS analysis is included in the method development, one employing a quadrupole MS system for compound identification and an isotope ratio MS for measuring the stable isotope ratios of deuterium and hydrogen (D/H) in fatty acids. Finally, the method for analyzing the compound abundance data is included. This study indicates that removal of ricinoleic acid is a conserved consequence of each processing step we tested. Furthermore, the stable isotope D/H ratio of ricinoleic acid distinguished between two of the three castor seed sources. Concentrations of arabinose, xylose, mannose, glucosamine and myo-inositol differentiated between crude or acetone extracted samples and samples produced by protein precipitation. Taken together these data illustrate the ability to distinguish between processes used to purify a ricin sample as well as potentially the source seeds.« less

Identification of minor acylglycerols less polar than triricinolein in castor oil by mass spectrometry and the proposed biosynthetic pathway of castor oil

USDA-ARS?s Scientific Manuscript database

Ricinoleate (OH18:1), a monohydroxy fatty acid, has many industrial uses such as the manufacture of biodegradable plastics, nylon, plasticizers, lubricants, cosmetics and paints. Castor oil is the only commericial source of ricinoleate which occurs as triacylglycerols. Triacylglycerols in castor oil...

Castor oil overdose

MedlinePlus

... overdose URL of this page: //medlineplus.gov/ency/article/002768.htm Castor oil overdose To use the sharing features on this page, please enable JavaScript. Castor oil is a yellowish liquid often used ...

Castor oil for induction of labour: a retrospective study.

PubMed

Neri, Isabella; Dante, Giulia; Pignatti, Lucrezia; Salvioli, Chiara; Facchinetti, Fabio

2018-08-01

The aim of this study is to investigate the safety and efficacy of castor oil to induce labour. A retrospective observational case control study was conducted over five years. Castor oil was proposed to women referred to the Birth Centre (Castor Oil group (COG)). They were compared to women who chose to be followed by the traditional doctor-led unit (control group (CG)). Castor oil was administered in a 60 ml single dose in 200 ml of warm water. Inclusion criteria were gestational age between 40 and 41 weeks plus premature rupture of membranes between 12 and 18 hours or amniotic fluid index ≤4 or Bishop Score of ≤4 or absence of spontaneous labour over 41 + 4 weeks. Pharmacological induction of labour was required for 18 women in the COG (45%) and 36 in the CG (90%) (p < .001). The mode of delivery differed significantly between groups: women assuming castor oil showed a higher incidence of vaginal delivery, whereas the incidence of caesarean section was lower in the COG, but no statistical significance was reached. The use of castor oil is related to a higher probability of labour initiation within 24 hours. Castor oil can be considered a safe non-pharmacological method for labour induction.

75 FR 44917 - Castor Oil, Ethoxylated, Dioleate; Tolerance Exemption

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-30

... of pesticide use in residential settings. If EPA is able to determine that a finite tolerance is not... of its composition the atomic elements carbon, hydrogen, and oxygen. 3. The polymer does not contain as an integral part of its composition, except as impurities, any element other than those listed in...

75 FR 40751 - Castor Oil, Ethoxylated, Oleate; Tolerance Exemption

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-14

... a finite tolerance is not necessary to ensure that there is a reasonable certainty that no harm will... contain as an integral part of its composition the atomic elements carbon, hydrogen, and oxygen. 3. The polymer does not contain as an integral part of its composition, except as impurities, any element other...

Simple Synthesis Hydrogenated Castor Oil Fatty Amide Wax and Its Coating Characterization.

PubMed

Yu, Xiuzhu; Wang, Ning; Zhang, Rui; Zhao, Zhong

2017-07-01

A simple method for incorporating amine groups in hydrogenated castor oil (HCO) to produce wax for beeswax or carnauba wax substitution in packaging and coating was developed. From the conversion rate of the products, HCO was reacted with ethanolamine at 150°C for 5 h, and the molar ratio of HCO and ethanolamine was 1:4. The hardness of the final product was seven times higher than that of beeswax, the cohesiveness of the final product was 1.3 times higher than that of beeswax and approximately one half of that of carnauba wax, and the melting point of the final product is 98°C. The Fourier transform Infrared spectroscopy showed that the amide groups were incorporated to form the amide products. In coating application, the results showed that the force of the final product coating cardboard was higher than that of beeswax and paraffin wax and less than that of carnauba wax. After 24 h soaking, the compression forces were decreased. HCO fatty acid wax can be an alternative wax for carnauba wax and beeswax in coating applications.

Oil content among the diverse castor genetic resources in the U.S. collection

USDA-ARS?s Scientific Manuscript database

Castor (Ricinus communis L.) contains oil used for medicine, as an ingredient in shampoo, soap, hand lotion, high-speed lubricants, and as a coating material. Due to its high oil content, oil derived from castor seeds is currently proposed to be used as a feedstock for biodiesel production. The USDA...

NTP technical report on the toxicity studies of Castor Oil (CAS No. 8001-79-4) in F344/N Rats and B6C3F1 Mice (Dosed Feed Studies).

PubMed

Irwin, R

1992-03-01

Castor oil is a natural oil derived from the seeds of the castor bean, Ricinus communis. It is comprised largely of triglycerides with a high ricinolin content. Toxicity studies with castor oil were performed by incorporating the material at concentrations as high as 10% in diets given to F344/N rats and B6C3F1 mice of both sexes for 13 weeks. Genetic toxicity studies also were performed and were negative for mutation induction in Salmonella typhimurium, for induction of sister chromatid exchanges or chromosomal aberrations in Chinese hamster ovary cells, and for induction of micronuclei in the peripheral blood erythrocytes of mice evaluated at the end of the 13-week studies. Exposure to castor oil at dietary concentrations as high as 10% in 13-week studies did not affect survival or body weight gains of rats or mice (10 per sex and dose). There were no biologically significant effects noted in hematologic analyses in rats. Mild increases in total bile acids and in serum alkaline phosphatase were noted at various times during the studies in rats receiving the higher dietary concentrations of castor oil. Liver weights were increased in male rats receiving the 10% dietary concentration and in male and female mice receiving diets containing 5% or 10% castor oil. However, there were no histopathologic lesions associated with these liver changes, nor were there any compound-related morphologic changes in any organ in rats or mice. No significant changes were noted in a screening for male reproductive endpoints, including sperm count and motility, and no changes were observed in the length of estrous cycles of rats or mice given diets containing castor oil. Thus, no significant adverse effects of castor oil administration were noted in these studies. Synonyms: Ricinus Oil, oil of Palma Christi, tangantangan oil, phorboyl, Neoloid.

Novel alpha-hydroxy phosphonic acids via castor oil

USDA-ARS?s Scientific Manuscript database

Hydroxy fatty acids (HFAs) have found a number of uses in today’s market, with uses ranging from materials to pharmaceuticals. Castor oil has served as a versatile HFA; its principle component, ricinoleic acid, can be isolated from castor oil and has been modified extensively for a number of applica...

Identification of minor acylglycerols less polar than triricinolein in castor oil by mass spectrometry

USDA-ARS?s Scientific Manuscript database

Triacylglycerols in castor oil less polar than triricinolein were identified by electrospray ionization – mass spectrometry using the lithium adducts of the acylglycerols from the HPLC fractions of castor oil. Thirty four new molecular species of acylglycerols containing hydroxy fatty acids in casto...

Identification of acylglycerols containing dihydroxy fatty acids in castor oil by mass spectrometry

USDA-ARS?s Scientific Manuscript database

Ricinoleate, a monohydroxy fatty acid, in castor oil has many industrial uses. Dihydroxy fatty acids can also be used in industry. The C18 HPLC fractions of castor oil were used for mass spectrometry of lithium addicts to identify the acylglycerols containing dihydroxy fatty acids. Four diacylglycer...

A high-oil castor cultivar developed through recurrent selection

USDA-ARS?s Scientific Manuscript database

The purpose of this paper is to present and interpret the data obtained from field-grown castor seeds. Under greenhouse conditions, a previous recurrent selection for high-oil castor seeds from a base population resulted in a new population with an increased mean oil content from 50.33 to 54.47% dry...

Formulation, characterization and pharmacokinetics of praziquantel-loaded hydrogenated castor oil solid lipid nanoparticles.

PubMed

Xie, Shuyu; Pan, Baoliang; Wang, Ming; Zhu, Luyan; Wang, Fenghua; Dong, Zhao; Wang, Xiaofang; Zhou, WenZhong

2010-07-01

The purpose of this study was to formulate praziquantel (PZQ)-loaded hydrogenated castor oil (HCO) solid lipid nanoparticles (SLN) to enhance the bioavailability and prolong the systemic circulation of the drug. PZQ was encapsulated into HCO nanoparticles by a hot homogenization and ultrasonication method. The physicochemical characteristics of SLN were investigated by optical microscope, scanning electron microscopy and photon correlation spectroscopy. Pharmacokinetics were studied after oral, subcutaneous and intramuscular administration in mice. The diameter, polydispersivity index, zeta potential, encapsulation efficiency and loading capacity of the nanoparticles were 344.0 +/- 15.1 nm, 0.31 +/- 0.08, -16.7 +/- 0.5 mV, 62.17 +/- 6.53% and 12.43 +/- 1.31%, respectively. In vitro release of PZQ-loaded HCO-SLN exhibited an initial burst release followed by a sustained release. SLN increased the bioavailability of PZQ by 14.9-, 16.1- and 2.6-fold, and extended the mean residence time of the drug from 7.6, 6.6 and 8.2 to 95.9, 151.6 and 48.2 h after oral, subcutaneous and intramuscular administration, respectively. The PZQ-loaded HCO-SLN could be a promising formulation to enhance the pharmacological activity of PZQ.

Investigation on the photostability of tretinoin in creams.

PubMed

Brisaert, M; Plaizier-Vercammen, J A

2007-04-04

In this investigation, the photodegradation of some tretinoin cream formulations was evaluated. Several oils were selected to prepare the cream formulations: olive oil, maize oil, castor oil, isopropyl myristate and Miglyol 812. A solubility study showed that tretinoin is best soluble in castor oil (0.60g/100ml), followed by isopropyl myristate, maize oil, Miglyol 812 and olive oil, respectively, 0.35, 0.30, 0.29 and 0.22g/100ml. The photostability of tretinoin in oils is comparable with the photostability of a tretinoin lotion (ethanol/propylene glycol 50/50), castor oil and olive oil giving slightly better results than the other oils. Investigation of the photodegradation of tretinoin in o/w creams, prepared with the same oils as mentioned above, revealed that tretinoin is far more stable in the cream formulations than in the respective oils, however it is not clear whether this is due to the formulation or due to a different irradiation technique. Tretinoin seemed to be most stable in the olive oil cream, followed by the castor oil cream. However microscopic investigation revealed the presence of tretinoin crystals in the olive oil cream, while the other creams were free of it. As a conclusion, one can say that the cream prepared with castor oil seems to be the most suitable one, in terms of solubility of tretinoin and in terms of photostability.

Efficiency of Castor Oil as a Storage Medium for Avulsed Teeth in Maintaining the Viability of Periodontal Ligament Cells.

PubMed

Nabavizadeh, Mohammadreza; Abbaszadegan, Abbas; Khodabakhsi, Afrooz; Ahzan, Shamseddin; Mehrabani, Davood

2018-03-01

Researchers always seek a new storage medium for avulsed teeth. Castor oil is a vegetable oil with several advantages such as antimicrobial and antioxidant properties, low toxicity, and glutathione preservation capability, low cost, and high availability. The purpose of this study was to evaluate and compare the capacity of castor oil as a new storage medium in preserving the viability of periodontal ligament (PDL) cells compared to Hank's balanced salt solution (HBSS) and milk. Forty freshly extracted human teeth were divided into 3 experimental and 2 control groups. The experimental teeth were stored dry for 30 min and then immersed for 45 min in one of the following media; castor oil, HBSS, and milk. The positive and negative control groups were exposed to 0 min and 2 h of dry time respectively with no immersion in any storage medium. The teeth were then treated with dispase grade II and collagenase and the number of viable PDL cells were counted. Data were analyzed using Kruskal- Wallis test. The percentage of viable cells treated with castor oil, HBSS and milk counted immediately after removal from these media were 46.93, 51.02 and 55.10 % respectively. The statistical analysis revealed that the value for castor oil was significantly lower than HBSS and milk ( p > 0.05). Within the parameters of this study, it appears that castor oil cannot be served as an ideal medium for storage of avulsed tooth. More investigations under in vivo conditions are required to justify the results of this study.

Castor (Ricinus communis L.)

USDA-ARS?s Scientific Manuscript database

The castor plant has been cultivated for thousands of years, providing a useful source of medicine, lamp fuel and lubricant long before petroleum came into wide use. The oil content of castor seed ranges from 45 to 60%, with most cultivars closer to 50% oil content. The presence of the hydroxy fatty...

Fetal death of dogs after the ingestion of a soil conditioner.

PubMed

Hong, Il-Hwa; Kwon, Tae-Eog; Lee, Seung-Keun; Park, Jin-Kyu; Ki, Mi-Ran; Park, Se-Il; Jeong, Kyu-Shik

2011-01-01

Castor beans (Ricinus communis) contain ricin, which is one of the most toxic substances of plant origin. Ricin toxicosis has been reported in different countries with usually ingestion of castor beans or plants in both animals and humans. However, ricin toxicosis by ingestion of some products containing castor oil cake has rarely been reported. This paper describes outbreaks of dog death by ricin toxicosis after accidental ingestion of the same soil conditioner. Fifteen dogs showed toxic symptoms such as severe vomiting, abdominal pain and hemorrhagic diarrhea, and then thirteen dogs died in a few days. The soil conditioner dogs ingested consisted of 10% castor oil cake containing ricin. On the basis of clinical signs, laboratory and pathologic findings, a diagnosis of ricin toxicosis was established in the present case. In comparison with previous cases by ingestion of castor beans, the dogs' morbidity was very high in the present case. The ingestion of castor oil cake may be more dangerous to life than the castor beans. It is because mortality by ingestion of castor beans depends on the degree of mastication of the beans, whereas ricin in oil cake is easily absorbed from the stomach and the intestines. As ricin is a heat-labile toxin, products containing ricin or oil cake should be properly treated with heat and have written caution sentences about toxicosis, and be kept out of reach of domestic animals and children. Copyright © 2009 Elsevier GmbH. All rights reserved.

[Comparative research on Cd removal from water by different kinds of seedlings].

PubMed

Wang, Yan-yan; Xu, Jing-bo; Sheng, Lian-xi

2007-05-01

Ecological effects of Cd removal from water and the changes of physiological and biochemical indexes of seedlings of maize, sunflower and castor-oil plant were investigated. The results showed that (1) with the trial time lasting, Cd content in solution decreased, and the processes of Cd removal by seedlings of each concentration were almost completed in 48 hours. The removal effects of sunflower and castor-oil plant were better than those of maize at 1 mg x L(-1) and 2 mg x L(-1) Cd, whereas the best removal effects at 5 mg x L(-1) and 10 mg x L(-) Cd were those of castor-oil plant, followed by maize and sunflower. (2) Root absorbed the most proportion of Cd by all these three kinds of seedlings at every treatment. The ability of Cd accumulation by the three kinds of seedlings could be drawn as follow sunflower> castor-oil plant > maize. (3) The physiological and biochemical indexes of seedlings exposed to Cd for 72 hours had changed to different degree compared with control. The root activity and the proline content of sunflower both have significant relations with Cd accumulation, and the plasma membrane permeability and the proline content of castor-oil plant both have significant positive relations with Cd accumulation. Maize, sunflower and castor-oil plant could endure certain concentration of Cd, and the tolerance of sunflower and castor-oil plant are both greater than that of maize through general analysis of Cd accumulation and the changes of physiological and biochemical indexes.

Castor oil as a natural alternative to labor induction: A retrospective descriptive study.

PubMed

DeMaria, Andrea L; Sundstrom, Beth; Moxley, Grace E; Banks, Kendall; Bishop, Ashlan; Rathbun, Lesley

2018-04-01

To describe birthing outcomes among women who consumed castor oil cocktail as part of a freestanding birth center labor induction protocol. De-identified data from birth logs and electronic medical records were entered into SPSS Statistics 22.0 for analysis for all women who received the castor oil cocktail (n=323) to induce labor between January 2008 and May 2015 at a birth center in the United States. Descriptive statistics were analyzed for trends in safety and birthing outcomes. Of the women who utilized the castor oil cocktail to stimulate labor, 293 (90.7%) birthed vaginally at the birth center or hospital. The incidence of maternal adverse effects (e.g., nausea, vomiting, extreme diarrhea) was less than 7%, and adverse effects of any kind were reported in less than 15% of births. An independent sample t-test revealed that parous women were more likely to birth vaginally at the birth center after using the castor oil cocktail than their nulliparous counterparts (p<.010), while gestational age (p=.26), woman's age (p=.23), and body mass index (p=.28) were not significantly associated. Nearly 91% of women in the study who consumed the castor oil cocktail to induce labor were able to give birth vaginally with little to no maternal or fetal complications. Findings indicate further research is needed to compare the safety and effectiveness of natural labor induction methodologies, including castor oil, to commonly used labor induction techniques in a prospective study or clinical trial. Copyright © 2017 Australian College of Midwives. Published by Elsevier Ltd. All rights reserved.

Genetic diversity and population structure of castor (Ricinus communis L.) germplasm within the U.S. collection assessed with EST-SSR markers

USDA-ARS?s Scientific Manuscript database

Castor is an important oilseed crop and although its oil is inedible, it has multiple industrial and pharmaceutical applications. The entire U.S. castor germplasm collection was previously screened for oil content and fatty acid composition, but its genetic diversity and population structure has not...

Paclitaxel Injection

MedlinePlus

... other medications. Paclitaxel injection manufactured with polyoxyethylated castor oil is used to treat ovarian cancer (cancer that ... and lung cancer. Paclitaxel injection with polyoxyethylated castor oil is also used to treat Kaposi's sarcoma (a ...

A survey of the castor oil content, seed weight and seed-coat colour on the United States Department of Agriculture germplasm collection.

USDA-ARS?s Scientific Manuscript database

Castor bean is an important non-edible oilseed crop that can potentially be used as feedstock for biodiesel production. Cultivars with a high percentage of oil content in seeds are preferred for biodiesel production. There are 1033 accessions in the USDA castor bean germplasm collection. The range o...

Changes in antioxidant and biochemical activities in castor oil-coated Capsicum annuum L. during postharvest storage.

PubMed

Panigrahi, Jitendriya; Patel, Mansi; Patel, Niyati; Gheewala, Bhumi; Gantait, Saikat

2018-06-01

This study, for the first time, evaluates the efficiency of castor oil when used as an external coating on Capsicum annuum L., to increase postharvest storage-life at 4 ± 1 °C. The castor oil-coated fruits were successfully stored for 36 days, while the non-coated fruits could only sustain for 18 days. Throughout the storage period (at 9-day intervals), different antioxidants and biochemical assays (allied with storage) such as titratable acidity, ascorbic acid content, ferrous ion chelating activity, reducing power, DPPH scavenging activity, hydroxyl radical scavenging activity, total phenolic content, total sugar estimation, and enzymatic study of polyphenol oxidase and pectate lyase, were assessed. During storage, the castor oil-coated fruits showed a substantial decrease in titratable acidity, ascorbic acid content, total phenolic content, including antioxidant activities such as reducing power and DPPH activity; however, an increase in ferrous ion chelating activity, total soluble sugar content, polyphenol oxidase activity and initial pectate lyase activity was observed, in contrast to that of the non-coated fruits. The application of castor oil proved to be effective in delaying the ripening process of fruits during storage.

Experimental investigation on performance and exhaust emissions of castor oil biodiesel from a diesel engine.

PubMed

Shojaeefard, M H; Etgahni, M M; Meisami, F; Barari, A

2013-01-01

Biodiesel, produced from plant and animal oils, is an important alternative to fossil fuels because, apart from dwindling supply, the latter are a major source of air pollution. In this investigation, effects of castor oil biodiesel blends have been examined on diesel engine performance and emissions. After producing castor methyl ester by the transesterification method and measuring its characteristics, the experiments were performed on a four cylinder, turbocharged, direct injection, diesel engine. Engine performance (power, torque, brake specific fuel consumption and thermal efficiency) and exhaust emissions were analysed at various engine speeds. All the tests were done under 75% full load. Furthermore, the volumetric blending ratios of biodiesel with conventional diesel fuel were set at 5, 10, 15, 20 and 30%. The results indicate that lower blends of biodiesel provide acceptable engine performance and even improve it. Meanwhile, exhaust emissions are much decreased. Finally, a 15% blend of castor oil-biodiesel was picked as the optimized blend of biodiesel-diesel. It was found that lower blends of castor biodiesel are an acceptable fuel alternative for the engine.

Toxin content of commercial castor cultivars

USDA-ARS?s Scientific Manuscript database

The castor plant Ricinus communis L. is the source of castor oil which has numerous uses and is a key chemical feedstock for an array of products from polymers to cosmetics. Although castor was once widely grown throughout the world, the presence of the toxic protein ricin has deterred the re-introd...

Castor diacylglycerol acyltransferase type1(DGAT1)displays greater activity with diricinolein than Arabidopsis DGAT1

USDA-ARS?s Scientific Manuscript database

Castor oil contains the hydroxy fatty acid ricinoleate as a major (90%) component. The diacylglycerol acyltransferase (DGAT) carries out the final reaction step in the biosynthesis of triacylglycerol, the principal constituent of seed oil, and has been considered to be the step that controls the oil...

Hydrogenated castor oil nanoparticles as carriers for the subcutaneous administration of tilmicosin: in vitro and in vivo studies.

PubMed

Han, C; Qi, C M; Zhao, B K; Cao, J; Xie, S Y; Wang, S L; Zhou, W Z

2009-04-01

Tilmicosin-loaded solid lipid nanoparticles (SLN) were prepared with hydrogenated castor oil (HCO) by o/w emulsion-solvent evaporation technique. The nanoparticle diameters, surface charges, drug loadings and encapsulation efficiencies of different formulations were 90 approximately 230 nm, -6.5 approximately -12.5 mV, 40.3 approximately 59.2% and 5.7 approximately 11.7% (w/w), respectively. In vitro release studies of the tilmicosin-loaded nanoparticles showed a sustained release and the released tilmicosin had the same antibacterial activity as that of the free drug. Pharmacokinetics study after subcutaneous administration to Balb/c mice demonstrated that a single dose of tilmicosin-loaded nanoparticles resulted in sustained serum drug levels (>0.1 microg/mL) for 8 days, as compared with only 5 h for the same amount of tilmicosin phosphate solution. The time to maximum concentration (Tmax), half-life of absorption (T(1/2) ab) and half-life of elimination (T(1/2) el) of tilmicosin-loaded nanoparticles were much longer than those of tilmicosin phosphate solution. Tissue section showed that drug-loaded nanoparticles caused no inflammation at the injection site. Cytotoxicity study in cell culture and acute toxicity test in mice demonstrated that the nanoparticles had little or no toxicity. The results of this exploratory study suggest that the HCO-SLN could be a useful system for the delivery of tilmicosin by subcutaneous administration.

Synthesis and characterization of gold nanotube/nanowire-polyurethane composite based on castor oil and polyethylene glycol.

PubMed

Ganji, Yasaman; Kasra, Mehran; Salahshour Kordestani, Soheila; Bagheri Hariri, Mohiedin

2014-09-01

Gold nanotubes/nanowires (GNT/NW) were synthesized by using the template-assisted electrodeposition technique and mixed with castor oil-polyethylene glycol based polyurethane (PU) to fabricate porous composite scaffolds for biomedical application. 100 and 50 ppm of GNT/NW were used to synthesize composites. The composite scaffolds were characterized by Fourier transform infrared spectroscopy, dynamic mechanical thermal analysis, differential scanning calorimetry, and scanning electron microscopy. Cell attachment on polyurethane-GNT/NW composites was investigated using fat-derived mesenchymal stem cells. Addition of 50 or 100 ppm GNT/NW had significant effects on thermal, mechanical, and cell attachment of polyurethane. Higher crosslink density and better cell attachment and proliferation were observed in polyurethane containing 50 ppm GNT/NW. The results revealed that GNT/NW formed hydrogen bonding with the polyurethane matrix and improved the thermomechanical properties of nanocomposites. Compared with pure PU, better cellular attachment on polyurethane-GNT/NW composites was observed resulting from the improved surface properties of composites. Copyright © 2014 Elsevier B.V. All rights reserved.

Design and development of low cost polyurethane biopolymer based on castor oil and glycerol for biomedical applications

PubMed Central

Tan, A. C. W.; Polo‐Cambronell, B. J.; Provaggi, E.; Ardila‐Suárez, C.; Ramirez‐Caballero, G. E.; Baldovino‐Medrano, V. G.

2017-01-01

Abstract In the current study, we present the synthesis of novel low cost bio‐polyurethane compositions with variable mechanical properties based on castor oil and glycerol for biomedical applications. A detailed investigation of the physicochemical properties of the polymer was carried out by using mechanical testing, ATR‐FTIR, and X‐ray photoelectron spectroscopy (XPS). Polymers were also tested in short term in‐vitro cell culture with human mesenchymal stem cells to evaluate their biocompatibility for potential applications as biomaterial. FTIR analysis confirmed the synthesis of castor oil and glycerol based PU polymers. FTIR also showed that the addition of glycerol as co‐polyol increases crosslinking within the polymer backbone hence enhancing the bulk mechanical properties of the polymer. XPS data showed that glycerol incorporation leads to an enrichment of oxidized organic species on the surface of the polymers. Preliminary investigation into in vitro biocompatibility showed that serum protein adsorption can be controlled by varying the glycerol content with polymer backbone. An alamar blue assay looking at the metabolic activity of the cells indicated that castor oil based PU and its variants containing glycerol are non‐toxic to the cells. This study opens an avenue for using low cost bio‐polyurethane based on castor oil and glycerol for biomedical applications. PMID:29159831

Phenylpropanoid esters of lesquerella and castor oil

USDA-ARS?s Scientific Manuscript database

Lesquerella (LO) and castor oil (CO) were esterified at the secondary hydroxyl groups of their 14-hydroxyeicos-cis-11-enoic fatty acids and 12-hydroxyoctadec-cis-9-enoic fatty acids, respectively, with 4-acetoxy-3-methoxycinnamic acid (acetoxyferulic acid). The unconventional esterifications were co...

21 CFR 73.2180 - Guaiazulene.

Code of Federal Regulations, 2013 CFR

2013-04-01

... ADDITIVES EXEMPT FROM CERTIFICATION Cosmetics § 73.2180 Guaiazulene. (a) Identity. (1) The color additive... cosmetic use may contain the following diluent: Polyethylene glycol-40 castor oil (PEG-40 castor oil... applied cosmetics in amounts consistent with good manufacturing practice. (d) Labeling. The label of the...

21 CFR 73.2180 - Guaiazulene.

Code of Federal Regulations, 2012 CFR

2012-04-01

... ADDITIVES EXEMPT FROM CERTIFICATION Cosmetics § 73.2180 Guaiazulene. (a) Identity. (1) The color additive... cosmetic use may contain the following diluent: Polyethylene glycol-40 castor oil (PEG-40 castor oil... applied cosmetics in amounts consistent with good manufacturing practice. (d) Labeling. The label of the...

21 CFR 73.2180 - Guaiazulene.

Code of Federal Regulations, 2014 CFR

2014-04-01

... ADDITIVES EXEMPT FROM CERTIFICATION Cosmetics § 73.2180 Guaiazulene. (a) Identity. (1) The color additive... cosmetic use may contain the following diluent: Polyethylene glycol-40 castor oil (PEG-40 castor oil... applied cosmetics in amounts consistent with good manufacturing practice. (d) Labeling. The label of the...

21 CFR 73.2180 - Guaiazulene.

Code of Federal Regulations, 2010 CFR

2010-04-01

... ADDITIVES EXEMPT FROM CERTIFICATION Cosmetics § 73.2180 Guaiazulene. (a) Identity. (1) The color additive... cosmetic use may contain the following diluent: Polyethylene glycol-40 castor oil (PEG-40 castor oil... applied cosmetics in amounts consistent with good manufacturing practice. (d) Labeling. The label of the...

Composition of acylglycerols in castor oil and their biosynthetic pathway

USDA-ARS?s Scientific Manuscript database

Castor oil has many industrial uses, such as the manufacture of aviation lubricant, plastics, paints, coatings, and cosmetics, because of its high content of ricinoleate (hydroxy fatty acid). We have identified many molecular species of acylglycerols using electrospray ionization mass spectrometry o...

Film-forming properties of castor oil polyol ester blends in elastohydrodynamic conditions

USDA-ARS?s Scientific Manuscript database

The viscosities and elastohydrodynamic (EHD) film thickness properties of binary blends of castor oil with polyol esters were determined experimentally. Predicted blend viscosity was calculated from the viscosity of the pure blend components. Measured viscosity values were closer to the values pre...

Evaluation of castor oil samples for potential toxin contamination

USDA-ARS?s Scientific Manuscript database

Castor oil and its derivatives are widely used as a chemical feedstock for production of lubricants and greases, and for engineering plastics, plasticizers and surfactants. They also have wide application in consumer goods such as lipstick, deodorants and medicinal products. Due to concerns about th...

Design and development of low cost polyurethane biopolymer based on castor oil and glycerol for biomedical applications.

PubMed

Tan, A C W; Polo-Cambronell, B J; Provaggi, E; Ardila-Suárez, C; Ramirez-Caballero, G E; Baldovino-Medrano, V G; Kalaskar, D M

2018-02-01

In the current study, we present the synthesis of novel low cost bio-polyurethane compositions with variable mechanical properties based on castor oil and glycerol for biomedical applications. A detailed investigation of the physicochemical properties of the polymer was carried out by using mechanical testing, ATR-FTIR, and X-ray photoelectron spectroscopy (XPS). Polymers were also tested in short term in-vitro cell culture with human mesenchymal stem cells to evaluate their biocompatibility for potential applications as biomaterial. FTIR analysis confirmed the synthesis of castor oil and glycerol based PU polymers. FTIR also showed that the addition of glycerol as co-polyol increases crosslinking within the polymer backbone hence enhancing the bulk mechanical properties of the polymer. XPS data showed that glycerol incorporation leads to an enrichment of oxidized organic species on the surface of the polymers. Preliminary investigation into in vitro biocompatibility showed that serum protein adsorption can be controlled by varying the glycerol content with polymer backbone. An alamar blue assay looking at the metabolic activity of the cells indicated that castor oil based PU and its variants containing glycerol are non-toxic to the cells. This study opens an avenue for using low cost bio-polyurethane based on castor oil and glycerol for biomedical applications. © 2017 The Authors Biopolymers Published by Wiley Periodicals, Inc.

Grape seed and apple tannins: emulsifying and antioxidant properties.

PubMed

Figueroa-Espinoza, Maria Cruz; Zafimahova, Andrea; Alvarado, Pedro G Maldonado; Dubreucq, Eric; Poncet-Legrand, Céline

2015-07-01

Tannins are natural antioxidants found in plant-based foods and beverages, whose amphiphilic nature could be useful to both stabilize emulsions and protect unsaturated lipids from oxidation. In this paper, the use of tannins as antioxidant emulsifiers was studied. The main parameters influencing the stability of emulsions (i.e. tannins structure and concentration, aqueous phase pH, and ionic strength) were identified and optimized. Oil in water emulsions stabilized with tannins were compared with those stabilized with two commercial emulsifying agents, poly(vinyl alcohol) (PVA) and polyoxyethylene hydrogenated castor oil. In optimized conditions, the condensed tannins allowed to obtain a stability equivalent to that of PVA. Tannins presented good antioxidant activity in oil in water emulsion, as measured by the conjugated autoxidizable triene (CAT) assay. Copyright © 2015 Elsevier Ltd. All rights reserved.

Synthesis of lesquerella a-hydroxy phosphonates

USDA-ARS?s Scientific Manuscript database

Hydroxy fatty acids (HFAs) have found a number of uses in today’s market, with uses ranging from industrial materials to pharmaceuticals. Castor oil, which is obtained from castor seeds, has served as a source of a versatile HFA; its principle component, ricinoleic acid, can be isolated from castor ...

A review on the challenges for increassed production of castor

USDA-ARS?s Scientific Manuscript database

The oil produced by castor (Ricinus communis) is an important raw material for chemical industry for its unique properties such as the only commercial source of a hydroxilated fatty acid that composes around 90% of the oil. This crop has a remarkable potential for increasing importance as a raw mate...

Biodiesel production from castor oil using heterogeneous Ni doped ZnO nanocatalyst.

PubMed

Baskar, G; Aberna Ebenezer Selvakumari, I; Aiswarya, R

2018-02-01

In the present study, castor oil with high free fatty acid was used for biodiesel production using heterogeneous Ni doped ZnO nanocatalyst. Ni doped ZnO nanocomposite calcinated at 800 °C has shown better catalytic activity. Process parameters on heterogeneous catalysis of castor oil into biodiesel were optimized using conventional and Response Surface Methodology (RSM). RSM was found more accurate in estimating the optimum conditions with higher biodiesel yield (95.20%). The optimum conditions for transesterification was found to be oil to methanol molar ratio of 1:8, catalyst loading 11% (w/w), reaction temperature of 55 °C for 60 min of reaction time by response surface method. The reusability studies showed that the nanocatalyst can be reused efficiently for 3 cycles. Copyright © 2017 Elsevier Ltd. All rights reserved.

Synthesis and application of a novel environmental C26 diglycidyl ester plasticizer based on castor oil for poly(vinyl chloride)

USDA-ARS?s Scientific Manuscript database

In this work, for the first time, a castor oil derived diglycidyl ester plasticizer (C26-DGE) was prepared and incorporated into poly(vinyl chloride) (PVC). The chemical structure of the product was characterized by Fourier transform infrared spectroscopy (FT-IR), proton nuclear magnetic resonance (...

Antidiarrheal and antinociceptive activities of ethanol extract and its chloroform and pet ether fraction of Phrynium imbricatum (Roxb.) leaves in mice.

PubMed

Hossain, Mohammed Munawar; Kabir, Mohammad Shah Hafez; Dinar, Md Abu Monsur; Arman, Md Saiful Islam; Rahman, Md Mominur; Hosen, S M Zahid; Dash, Raju; Uddin, Mir Muhammad Nasir

2017-09-26

The objective of the study was to evaluate the antidiarrheal and antinociceptive activities of ethanol extract and its chloroform and pet ether fraction of Phrynium imbricatum (Roxb.) leaves in mice. In the present study, the dried leaves of P. imbricatum were subjected to extraction with ethanol, and then it was fractioned by chloroform and pet ether solvent. Antidiarrheal effects were tested by using castor oil-induced diarrhea, castor oil-induced enteropooling, and gastrointestinal transit test. Antinociceptive activity was evaluated by using the acetic acid-induced writhing test and formalin-induced paw licking test. The standard drug loperamide (5 mg/kg) showed significant (p<0.001) inhibitory activity against castor oil-induced diarrhea, in which all the examined treatments decreased the frequency of defecation and were found to possess an anti-castor oil-induced enteropooling effect in mice by reducing both weight and volume of intestinal content significantly, and reducing the propulsive movement in castor oil-induced gastrointestinal transit using charcoal meal in mice. The results showed that the ethanol extract of P. imbricatum leaves has significant dose-dependent antinociceptive activity, and among its two different fractions, the pet ether fraction significantly inhibited the abdominal writhing induced by acetic acid and the licking times in formalin test at both phases. These findings suggest that the plant may be a potential source for the development of a new antinociceptive drug and slightly suitable for diarrhea, as it exhibited lower activity. Our observations resemble previously published data on P. imbricatum leaves.

Identification of hydroxy fatty acid and triacylglycerol metabolism-related genes in lesquerella through seed transcriptome analysis

USDA-ARS?s Scientific Manuscript database

Background: Castor oil is the only commercial source of hydroxy fatty acid which has industrial value. The production of castor oil is hampered by the presence of the toxin ricin in its seed. Lesquerella seed also accumulates hydroxy fatty acid and is free of ricin, thus it is being developed as a n...

The influence of plasticizers on the release of theophylline from microporous-controlled tablets.

PubMed

Lin, W J; Lee, H K; Wang, D M

2004-10-19

The aim of present work was to investigate the influence of plasticizer on the release of theophylline from microporous-controlled tablets. Three plasticizers, acetyltributyl citrate (ATBC), castor oil, and triacetin, were included in this study. These plasticizers reduced the crystallinity of poly(epsilon-caprolactone) (PCL)/poly(ethylene glycol) (PEG)-blended films, and the most prominent change of enthalpy of fusion was the film plasticized by triacetin. This might be due to triacetin penetrating into both PCL and PEG domains. However, the lipophilic property of castor oil only allowed it to alter the crystallization of hydrophobic PCL domain. The Young's modulus and the tensile strength of films showed a decreased tendency while increasing the amount of plasticizer. The change of elongation of plasticized blended films was irregular and was dependent of the type of plasticizer. The size of micropores formed in the presence of plasticizer was larger than those micropores formed in its absence. The fatty plasticizer, castor oil, altered the thermal and mechanical performance and pore size of films via soluble in PCL domain, which resulted in the release of theophylline from castor oil plasticized-coated tablets, which in turn enhanced and closed to a constant release pattern.

Intravenous tacrolimus and cyclosporine induced anaphylaxis: what is next?

PubMed Central

Kang, Sung-Yoon; Sohn, Kyoung-Hee; Lee, Jeong-Ok; Kim, Sae-Hoon; Cho, Sang-Heon

2015-01-01

Tacrolimus and cyclosporine have been used in various formulations, but their hypersensitivity reactions are rare in practice. Castor oil derivatives are nonionic surfactants used in aqueous preparations of hydrophobic active pharmaceutical ingredients. Castor oil derivatives that can be used as additives to tacrolimus and cyclosporine may play a role in the development of hypersensitivity reactions, especially anaphylaxis. Various immunologic and nonimmunologic mechanisms have been implicated in hypersensitivity reactions induced by castor oil derivatives. Physicians should be aware that not only the drug itself, but also its additives or metabolites could induce hypersensitivity reactions. We report a case of anaphylaxis caused by vitamin K (phytonadine), serotonin antagonist (granisetron), intravenous tacrolimus, and cyclosporine. Interestingly, the patient tolerated oral cyclosporine, which did not contain Cremophor EL or polysorbate 80. PMID:26240796

Synthesis and characterization of dialkanolamides from castor oil (Ricinus communis) as nonionic surfactant

NASA Astrophysics Data System (ADS)

Anwar, M.; Wahyuningsih, T. D.

2017-12-01

Nonionic surfactant of dialkanolamide derivates was synthesized and characterized from castor oil (Ricinus comunnis). Ricinoleic acid was isolated from castor oil by hydrolysis in alkaline (KOH) condition at 65 °C. Oxidation of ricinoleic acid by dilute potassium permanganate (KMnO4) in alkaline condition at 75-90 °C gave dicarboxylic acid which was then reacted with ethanolamine at 140-160 °C for 6 hours. The product was recrystallized with isopropanol, and the structure elucidation was performed by FTIR, 1HNMR spectrometer, and GC-MS with silylation method. Characterization of surfactants was carried out by surface tension measurement (capillary rise method), Critical Micelle Concentration (CMC) based on turbidity method and calculation of Hydrophilic-Lipophilic Balance (HLB) value with Griffin method and Bancroft rule. The result showed that ricinoleic acid in castor oil is 86.19 % and it is oxidation give an azelaic acid and octanedioic acid in 53.25 %. Amidation of a dicarboxylic acid and ethanolamine at 140-160 °C for 6 hours yielded of N1,N9-bis(2-hydroxyethyl)nona diamide in 49.35 %. Surfactant characterization indicates that dialkanolamide derivates can be used as a surfactant due to its ability to reduce the surface tension of ethanol with CMC at 1.2 g/L, HLB value is 5.58 and can be used as emulsifier water in oil (W/O).

Meat quality assessment from young goats fed for long periods with castor de-oiled cake.

PubMed

Oliveira, C H A; Silva, A M; Silva, L M; van Tilburg, M F; Fernandes, C C L; Moura, A A; Moreno, F B M B; Monteiro-Moreira, A C O; Moreira, R A; Bezerra, F J; Rondina, D

2015-08-01

Diet can influence both the qualitative and quantitative traits of ruminant meat. This study evaluated the effects of castor de-oiled cake on the meat of mixed-breed male goat kids. After 165days of diet treatment, no alterations (p>0.05) were observed in the in vivo performance, anatomic components, dissection and proximate composition of the Longissimus dorsi muscle, as well as in the color and pH of the carcasses. However, diet had an effect (p<0.05) on energy metabolites, fatty acid profile, and expression of certain proteins of the Longissimus dorsi muscle. To conclude, this study showed that the establishment of castor de-oiled cake diet for a long period to goats led to alterations in meat quality, without compromising its consumption qualities. Copyright © 2015 Elsevier Ltd. All rights reserved.

Histologic and immunohistochemical evaluation of biocompatibility of castor oil polyurethane polymer with calcium carbonate in equine bone tissue.

PubMed

Nóbrega, Fernanda S; Selim, Mariana B; Arana-Chavez, Victor E; Correa, Luciana; Ferreira, Márcio P; Zoppa, André L V

2017-10-01

OBJECTIVE To evaluate the efficacy of castor oil polyurethane polymer with calcium carbonate for use in a unicortical ostectomy on the dorsal surface of the third metacarpal bone of horses. ANIMALS 6 adult horses. PROCEDURES A unicortical ostectomy was created on the dorsal surface of both third metacarpal bones of each horse. Castor bean (Ricinus communis) oil polyurethane polymer with calcium carbonate was implanted into the ostectomy on 1 limb, and the ostectomy of the contralateral limb was left unfilled and served as a control sample. Ostectomy sites were evaluated histologically 120 days later. Biopsy specimens were obtained from the interface of bone and polymer or the interface of bone and newly formed tissue; specimens were processed for histomorphometric evaluation by use of light microscopy, immunohistochemical analysis, histochemical analysis, and transmission electron microscopy. RESULTS Osteoconductive activity of the biomaterial was confirmed by the presence of osteoblasts in the biopsy specimens. Absence of a chronic inflammatory response or foreign body reaction indicated biocompatibility. Expression of osteoblast markers was detected in the newly formed tissue. CONCLUSIONS AND CLINICAL RELEVANCE Results indicated that castor oil polyurethane polymer with calcium carbonate could be an acceptable compound for use as a bone substitute in horses with fractures in which bone filling is necessary.

Performance of maleated castor oil based plasticizer on rubber: rheology and curing characteristic studies

NASA Astrophysics Data System (ADS)

Indrajati, I. N.; Dewi, I. R.

2017-07-01

The objective of this study was to evaluate the performance of maleated castor oil (MACO) as plasticizer on natural rubber (NR), ethylene propylene diene monomer (EPDM), and nitrile butadiene rubber (NBR). The parameter studied were involving rheological, curing and swelling properties. The MACOs were prepared by an esterification reaction between castor oil (CO) and maleic anhydride (MAH) with the help of xylene as water entrainer to improve water removal. Resulting oils then applied as a plasticizer in each of those rubbers within a fixed loading of 5 phr. Comparison has been made to evaluate the performance of MACO and conventional plasticizer (paraffinic oil for NR and EPDM, DOP for NBR) on each rubber. Rheology, curing characteristic and swelling of each rubber were studied. The results showed that rubber (NR/EPDM/NBR) plasticized with MACO had given similar flow characteristic to conventional plasticizers. MACO exhibited slow curing, confirmed by higher t90, but the scorch safety was of the same magnitude. MAH loading tended to decrease the flow properties and curing rate, while scorch time (ts2) was independent.

Evaluation of the antimicrobial activity of three irrigating solutions in teeth with pulpal necrosis.

PubMed

Ferreira, C M; Bonifácio, K C; Fröner, I C; Ito, I Y

1999-01-01

The antimicrobial activity of 0.4% papaine gel (FCF-USP), an antibacterial product derived from 3.3% castor oil (IQSC-USP), and 0.5% sodium hypochlorite (FORP-USP) was evaluated in teeth with radiographically visible pulpal necrosis and periapical lesion in vivo. After cavity access, under aseptic conditions, a first harvesting was performed. The 3 irrigating solutions were used for biomechanical preparation. After 72 hours, a second harvesting was performed, also under aseptic conditions. The number of colony forming units (cfu) was counted with a stereomicroscope under reflected light. Castor oil and 0.5% sodium hypochlorite presented similar antimicrobial activities for the reduction of the anaerobe number, S. mutans and streptococci; however, the papaine gel showed lower activity. We conclude that both castor oil and sodium hypochlorite are effective as antimicrobial agents and can be used in the treatment of root canals with pulpal necrosis.

Preparation and evaluation of tilmicosin-loaded hydrogenated castor oil nanoparticle suspensions of different particle sizes.

PubMed

Chen, Xiaojin; Wang, Ting; Lu, Mengmeng; Zhu, Luyan; Wang, Yan; Zhou, WenZhong

2014-01-01

Three tilmicosin-loaded hydrogenated castor oil nanoparticle (TMS-HCO-NP) suspensions of different particle sizes were prepared with different polyvinyl alcohol surfactant concentrations using a hot homogenization and ultrasonic technique. The in vitro release, in vitro antibacterial activity, mammalian cytotoxicity, acute toxicity in mice, and stability study were conducted to evaluate the characteristics of the suspensions. The in vitro tilmicosin release rate, antibacterial activity, mammalian cytotoxicity, acute toxicity in mice, and stability of the suspensions were evaluated. When prepared with polyvinyl alcohol concentrations of 0.2%, 1%, and 5%, the mean diameters of the nanoparticles in the three suspensions were 920±35 nm, 452±10 nm, and 151±4 nm, respectively. The three suspensions displayed biphasic release profiles similar to that of freeze-dried TMS-HCO-NP powders, with the exception of having a faster initial release. Moreover, suspensions of smaller-sized particles showed faster initial release, and lower minimum inhibitory concentrations and minimum bactericidal concentrations. Time-kill curves showed that within 12 hours, the suspension with the 151 nm particles had the most potent bactericidal activity, but later, the suspensions with larger-sized particles showed increased antibacterial activity. None of the three suspensions were cytotoxic at clinical dosage levels. At higher drug concentrations, all three suspensions showed similar concentration-dependent cytotoxicity. The suspension with the smallest-sized particle showed significantly more acute toxicity in mice, perhaps due to faster drug release. All three suspensions exhibited good stability at 4°C and at room temperature for at least 6 months. These results demonstrate that TMS-HCO-NP suspensions can be a promising formulation for tilmicosin, and that nanoparticle size can be an important consideration for formulation development.

Preparation and evaluation of tilmicosin-loaded hydrogenated castor oil nanoparticle suspensions of different particle sizes

PubMed Central

Chen, Xiaojin; Wang, Ting; Lu, Mengmeng; Zhu, Luyan; Wang, Yan; Zhou, WenZhong

2014-01-01

Three tilmicosin-loaded hydrogenated castor oil nanoparticle (TMS-HCO-NP) suspensions of different particle sizes were prepared with different polyvinyl alcohol surfactant concentrations using a hot homogenization and ultrasonic technique. The in vitro release, in vitro antibacterial activity, mammalian cytotoxicity, acute toxicity in mice, and stability study were conducted to evaluate the characteristics of the suspensions. The in vitro tilmicosin release rate, antibacterial activity, mammalian cytotoxicity, acute toxicity in mice, and stability of the suspensions were evaluated. When prepared with polyvinyl alcohol concentrations of 0.2%, 1%, and 5%, the mean diameters of the nanoparticles in the three suspensions were 920±35 nm, 452±10 nm, and 151±4 nm, respectively. The three suspensions displayed biphasic release profiles similar to that of freeze-dried TMS-HCO-NP powders, with the exception of having a faster initial release. Moreover, suspensions of smaller-sized particles showed faster initial release, and lower minimum inhibitory concentrations and minimum bactericidal concentrations. Time-kill curves showed that within 12 hours, the suspension with the 151 nm particles had the most potent bactericidal activity, but later, the suspensions with larger-sized particles showed increased antibacterial activity. None of the three suspensions were cytotoxic at clinical dosage levels. At higher drug concentrations, all three suspensions showed similar concentration-dependent cytotoxicity. The suspension with the smallest-sized particle showed significantly more acute toxicity in mice, perhaps due to faster drug release. All three suspensions exhibited good stability at 4°C and at room temperature for at least 6 months. These results demonstrate that TMS-HCO-NP suspensions can be a promising formulation for tilmicosin, and that nanoparticle size can be an important consideration for formulation development. PMID:24920902

Tilmicosin- and florfenicol-loaded hydrogenated castor oil-solid lipid nanoparticles to pigs: Combined antibacterial activities and pharmacokinetics.

PubMed

Ling, Z; Yonghong, L; Junfeng, L; Li, Z; Xianqiang, L

2018-04-01

The combined antibacterial effects of tilmicosin (TIL) and florfenicol (FF) against Actinobacillus pleuropneumoniae (APP) (n = 2), Streptococcus suis (S. suis) (n = 2), and Haemophilus parasuis (HPS) (n = 2) were evaluated by chekerboard test and time-kill assays. The pharmacokinetics (PKs) of TIL- and FF-loaded hydrogenated castor oil (HCO)-solid lipid nanoparticles (SLN) were performed in healthy pigs. The results indicated that TIL and FF showed synergistic or additive antibacterial activities against APP, S. suis and HPS with the fractional inhibitory concentration (FIC) ranging from 0.375 to 0.75. The time-kill assays showed that 1/2 minimum inhibitory concentration (MIC) TIL combined with 1/2 MIC FF had a stronger ability to inhibit the growth of APP, S. suis, and HPS than 1 MIC TIL or 1 MIC FF, respectively. After oral administration, plasma TIL and FF concentrations could maintain about 0.1 μg/ml for 192 and 176 hr. The SLN prolonged the last time point with detectable concentrations (T last ), area under the concentration-time curve (AUC 0-t ), elimination half-life (T ½ke ), and mean residence time (MRT) by 3.1, 5.6, 12.7, 3.4-fold of the active pharmaceutical ingredient (API) of TIL and 11.8, 16.5, 18.1, 12.1-fold of the API of FF, respectively. This study suggests that the TIL-FF-SLN could be a useful oral formulation for the treatment of APP, S. suis, and HPS infection in pigs. © 2017 John Wiley & Sons Ltd.

Preparation, characterization, and pharmacokinetics of tilmicosin- and florfenicol-loaded hydrogenated castor oil-solid lipid nanoparticles.

PubMed

Ling, Z; Yonghong, L; Changqing, S; Junfeng, L; Li, Z; Chunyu, J; Xianqiang, L

2017-06-01

To effectively control bovine mastitis, tilmicosin (TIL)- and florfenicol (FF)-loaded solid lipid nanoparticles (SLN) with hydrogenated castor oil (HCO) were prepared by a hot homogenization and ultrasonication method. In vitro antibacterial activity, properties, and pharmacokinetics of the TIL-FF-SLN were studied. The results demonstrated that TIL and FF had a synergistic or additive antibacterial activity against Streptococcus dysgalactiae, Streptococcus uberis, and Streptococcus agalactiae. The size, polydispersity index, and zeta potential of nanoparticles were 289.1 ± 13.7 nm, 0.31 ± 0.05, and -26.7 ± 1.3 mV, respectively. The encapsulation efficiencies for TIL and FF were 62.3 ± 5.9% and 85.1 ± 5.2%, and the loading capacities for TIL and FF were 8.2 ± 0.6% and 3.3 ± 0.2%, respectively. The TIL-FF-SLN showed no irritation in the injection site and sustained release in vitro. After medication, TIL and FF could maintain about 0.1 μg/mL for 122 and 6 h. Compared to the control solution, the SLN increased the area under the concentration-time curve (AUC 0-t ), elimination half-life (T ½ke ), and mean residence time (MRT) of TIL by 33.09-, 23.29-, and 37.53-fold, and 1.69-, 5.00-, and 3.83-fold for FF, respectively. These results of this exploratory study suggest that the HCO-SLN could be a useful system for the delivery of TIL and FF for bovine mastitis therapy. © 2016 John Wiley & Sons Ltd.

Chemistry and physical properties of estolides

USDA-ARS?s Scientific Manuscript database

Estolides are a developing class of natural and synthetic compounds that have been synthesized from hydroxy oils, like castor and lesquerella, or by the condensation of fatty acids across the olefin of a second fatty acid. Castor and lesquerella estolides are derived from either their triglycerides...

Detoxification of castor meal through reactive seed crushing

USDA-ARS?s Scientific Manuscript database

Non-edible oil crops, such as castor or jatropha, contain several toxic components. Post-harvest treatments should be used to reduce the risks associated with the possible dispersion of toxic compounds in the environment. A new processing technology named Reactive Seed Crushing was developed, which ...

Anaphylactic shock following castor bean contact: a case report.

PubMed

Coattrenec, Y; Jaques, D; Jandus, P; Harr, T; Spoerl, D

2017-01-01

The castor bean plant, Ricinus communis , is known to have allergenic and toxic properties. Castor bean allergy has been described mainly as an occupational inhalation allergy in laboratory workers, in persons working in oil processing mills or in agricultural industry. So far, only one case of anaphylactic reaction due to castor bean sensitization confirmed by specific IgE has been described in literature. A 30-year-old woman presented to the emergency room with severe angioedema followed by urticaria, hypotension and tachycardia. She recovered after treatment with antihistamines, corticosteroids, nebulized adrenaline and intravenous fluids. Food induced anaphylaxis was excluded by allergological investigations. After repeated thorough history, the patient mentioned having bitten into a castor bean just before the reaction. Cutaneous test (prick-to-prick) and specific IgE for castor bean were highly positive. We report the second case of a severe anaphylactic reaction to castor beans, confirmed by IgE testing, reported in the literature. It underlines the importance of a meticulous history in allergology and highlights the fact, that castor beans may cause potentially fatal anaphylaxis.

The use of castor oil and ricinoleic acid in lead chalcogenide nanocrystal synthesis

NASA Astrophysics Data System (ADS)

Kyobe, Joseph W. M.; Mubofu, Egid B.; Makame, Yahya M. M.; Mlowe, Sixberth; Revaprasadu, Neerish

2016-08-01

A green solution-based thermolysis method for the synthesis of lead chalcogenide (PbE, E = S, Se, Te) nanocrystals in castor oil (CSTO) and its isolate ricinoleic acid (RA) is described. The blue shift observed from the optical spectra of CSTO and RA-capped PbE nanocrystals (NCs) confirmed the evidence of quantum confinement. The dimensions of PbE NCs obtained from NIR absorption spectra, transmission electron microscopy (TEM), and X-ray diffraction (XRD) studies were in good agreement. The particle sizes estimated were in the range of 20, 25, and 130 nm for castor oil-capped PbS, PbSe, and PbTe, respectively. Well-defined close to cubic-shaped particles were observed in the scanning electron microscopy (SEM) images of PbSe and PbTe nanocrystals. The high-resolution TEM and selective area electron diffraction (SAED) micrographs of the as-synthesized crystalline PbE NCs showed distinct lattice fringes with d-spacing distances corroborating with the standard values reported in literature.

One-pot conjugated linoleic acid production from castor oil by Rhizopus oryzae lipase and resting cells of Lactobacillus plantarum.

PubMed

Khaskheli, Abid Ali; Talpur, Farah Naz; Cebeci Aydin, Aysun; Jawaid, Sana; Surhio, Muhammad Ali; Afridi, Hassan Imran

2017-10-01

Conjugated linoleic acid (CLA) has attracted as novel type of fatty acids having unusual health-promoting properties such as anticarcinogenic and antiobesitic effects. The present work employed castor oil as substrate for one-pot production of CLA using washed cells of Lactobacillus plantarum (L. plantarum) and lipases as catalysts. Among the screened lipases, the lipase Rhizopus oryzae (ROL) greatly assisted resting cells to produce CLA. Mass spectral analysis of the product showed that two major isomers of CLA were produced in the reaction mixture i.e. cis-9, trans-11 56.55% and trans-10, cis-12 43.45%. Optimum factors for CLA synthesis were found as substrate concentration (8 mg/mL), pH (6.5), washed cell concentration (12% w/v), and incubation time of 20 h. Hence, the combination of ROL with L. plantarum offers one pot production of CLA selectively using castor oil as a cost-effective substrate.

Biotechnology for improved hHydroxy fatty acid production in oilseed lesquerella

USDA-ARS?s Scientific Manuscript database

The conventional source of hydroxy fatty acid (HFA) is from castor (Ricinus communis), 90% of castor oil is ricinoleic acid (18:1OH). Ricinoleic acid and its derivatives are used as raw materials for numerous industrial products, such as lubricants, plasticizers and surfactants. The production of ca...

Elastohydrodynamic Traction Properties of Seed Oils

USDA-ARS?s Scientific Manuscript database

The elastohydrodynamic traction coefficient (tc) properties of nine seed oils of varying chemical structures, PAO and hexadecane, were investigated using a ball-on disk traction apparatus. The seed oils were: castor oil, a triglyceride with hydroxyl functional group; jojoba, a monoglyceride; and s...

Sequential interpenetrating polymer networks produced from vegetable oil based polyurethane and poly(methyl methacrylate).

PubMed

Kong, Xiaohua; Narine, Suresh S

2008-08-01

Sequential interpenetrating polymer networks (IPNs) were prepared using polyurethane produced from a canola oil based polyol with primary terminal functional groups and poly(methyl methacrylate) (PMMA). The properties of the material were studied and compared to the IPNs made from commercial castor oil using dynamic mechanical analysis, differential scanning calorimetry, as well as tensile measurements. The morphology of the IPNs was investigated using scanning electron microscopy and transmission electron microscopy. The chemical diversity of the starting materials allowed the evaluation of the effects of dangling chains and graftings on the properties of the IPNs. The polymerization process of canola oil based IPNs was accelerated because of the utilization of polyol with primary functional groups, which efficiently lessened the effect of dangling chains and yielded a higher degree of phase mixing. The mechanical properties of canola oil based IPNs containing more than 75 wt % PMMA were comparable to the corresponding castor oil based IPNs; both were superior to those of the constituent polymers due to the finely divided rubber and plastic combination structures in these IPNs. However, when PMMA content was less than 65 wt %, canola oil based IPNs exhibited a typical mechanical behavior of rigid plastics, whereas castor oil based IPNs showed a typical mechanical behavior of soft rubber. It is proposed that these new IPN materials with high performance prepared from alternative renewable resources can prove to be valuable substitutes for existing materials in various applications.

Simultaneous allergen inactivation and detoxification of castor bean cake by treatment with calcium compounds

PubMed Central

Fernandes, K.V.; Deus-de-Oliveira, N.; Godoy, M.G.; Guimarães, Z.A.S.; Nascimento, V.V.; de Melo, E.J.T.; Freire, D.M.G.; Dansa-Petretski, M.; Machado, O.L.T.

2012-01-01

Ricinus communis L. is of great economic importance due to the oil extracted from its seeds. Castor oil has been used for pharmaceutical and industrial applications, as a lubricant or coating agent, as a component of plastic products, as a fungicide or in the synthesis of biodiesel fuels. After oil extraction, a castor cake with a large amount of protein is obtained. However, this by-product cannot be used as animal feed due to the presence of toxic (ricin) and allergenic (2S albumin) proteins. Here, we propose two processes for detoxification and allergen inactivation of the castor cake. In addition, we establish a biological test to detect ricin and validate these detoxification processes. In this test, Vero cells were treated with ricin, and cell death was assessed by cell counting and measurement of lactate dehydrogenase activity. The limit of detection of the Vero cell assay was 10 ng/mL using a concentration of 1.6 × 105 cells/well. Solid-state fermentation (SSF) and treatment with calcium compounds were used as cake detoxification processes. For SSF, Aspergillus niger was grown using a castor cake as a substrate, and this cake was analyzed after 24, 48, 72, and 96 h of SSF. Ricin was eliminated after 24 h of SSF treatment. The cake was treated with 4 or 8% Ca(OH)2 or CaO, and both the toxicity and the allergenic properties were entirely abolished. A by-product free of toxicity and allergens was obtained. PMID:22911344

Elastohydrodynamic (EHD) traction properties of seed oils

USDA-ARS?s Scientific Manuscript database

The elastohydrodynamic traction coefficient (tc) properties of nine seed oils of varying chemical structures, PAO and hexadecane, were investigated using a ball-on disk traction apparatus. The seed oils were: castor oil, a triglyceride with hydroxyl functional group; jojoba, a monoglyceride; and sev...

Local sustained delivery of bupivacaine HCl from a new castor oil-based nanoemulsion system.

PubMed

Rachmawati, Heni; Arvin, Yang Aryani; Asyarie, Sukmadjaja; Anggadiredja, Kusnandar; Tjandrawinata, Raymond Rubianto; Storm, Gert

2018-06-01

Bupivacaine HCl (1-butyl-2',6'-pipecoloxylidide hydrochloride), an amide local anesthetic compound, is a local anesthetic drug utilized for intraoperative local anesthesia, post-operative analgesia and in the treatment of chronic pain. However, its utility is limited by the relative short duration of analgesia after local administration (approximately 9 h after direct injection) and risk for side effects. This work is aimed to develop a nanoemulsion of bupivacaine HCl with sustained local anesthetics release kinetics for improved pain management, by exhibiting extended analgesic action and providing reduced peak levels in the circulation to minimize side effects. Herein, biodegradable oils were evaluated for use in nanoemulsions to enable sustained release kinetics of bupivacaine HCl. Only with castor oil, a clear and stable nanoemulsion was obtained without the occurrence of phase separation over a period of 3 months. High loading of bupivacaine HCl into the castor oil-based nanoemulsion system was achieved with about 98% entrapment efficiency and the resulting formulation showed high stability under stress conditions (accelerated stability test) regarding changes in visual appearance, drug content, and droplet size. We show herein that the in vitro release and in vivo pharmacokinetic profiles as well as pharmacodynamic outcome (pain relief test) after subcutaneous administration in rats correlate well and clearly demonstrate the prolonged release and extended duration of activity of our novel nanoformulation. In addition, the lower C max value achieved in the blood compartment suggests the possibility that the risk for systemic side effects is reduced. We conclude that castor oil-based nanomulsion represents an attractive pain treatment possibility to achieve prolonged local action of bupivacaine HCl.

Semisolid matrix filled capsules: an approach to improve dissolution stability of phenytoin sodium formulation.

PubMed

El Massik, M A; Abdallah, O Y; Galal, S; Daabis, N A

2003-05-01

Seven semisolid fill bases were selected for the formulation of 24 capsule formulations, each containing 100 mg of phenytoin sodium. The fill materials were selected based on the water absorption capacity of their mixtures with phenytoin sodium. The fill matrices included lipophilic bases (castor oil, soya oil, and Gelucire (G) 33/01), amphiphilic bases (G 44/14 and Suppocire BP), and water-soluble bases (PEG 4000 and PEG 6000). The drug:base ratio was 1:2. Excipients such as lecithin, docusate sodium, and poloxamer 188 were added to some formulations. The dissolution rate study indicated that formulations containing lipophilic and amphiphilic bases showed the best release profiles. These are F4 (castor oil-1% docusate sodium); F10 (castor oil-3% poloxamer 188); F14 (G33/01-10% lecithin); F17 (G33/01-1% docusate sodium), and F20 (Suppocire BP). Further, the dissolution stability of the five formulations above was assessed by an accelerated stability study at 30 degrees C and 75% RH using standard Epanutin capsules for comparison. The study included the test and standard capsules either packed in the container of marketed Epanutin capsules (packed) or removed from their outer pack (unpacked). Release data indicated superior release rates of castor oil based formulations (F4 and F10) relative to standard capsules in both the unpacked and packed forms. For instance, the extent of drug release at 30 min after 1 month was 91% for F4 and F10 and 20% for standard capsules. Drug release from packed capsules after 6 months storage was 88% for both formulations F4 and F10 and 35% for standard capsules. In conclusion, the pharmaceutical quality of phenytoin sodium capsules can be improved by using a semisolid lipophilic matrix filled in hard gelatin capsules.

Elastohydrodynamics of farm-based blends comprising amphiphilic oils

USDA-ARS?s Scientific Manuscript database

Vegetable oils contain non-polar hydrocarbon chains and polar ester groups (and possibly also other functional groups such as hydroxyl groups in castor oil). The presence of polar and non-polar groups within the same molecule gives vegetable oil amphiphilic character. The density, refractive index, ...

Anti-diarrhoeal and anti-microbial activity of Flos populi (male inflorescence of Populus tomentosa Carrière) aqueous extracts.

PubMed

Xu, Qianqian; Shen, Zhiqiang; Wang, Yubo; Guo, Shijin; Li, Feng; Wang, Yanping; Zhou, Chunfeng

2013-07-09

Flos populi (male inflorescence of Populus tomentosa Carrière) has been traditionally used in East Asian countries for the treatment of various inflammatory diseases, strengthening the spleen and stomach, anti-rheumatic, anti-tumor and anti-diarrhoeal. To evaluate the in vivo or in vitro anti-diarrhoeal and anti-microbial activity of Flos populi aqueous extract. Acute toxicity of Flos populi aqueous extract (FPAE) was investigated. Castor oil-induced diarrhoea method was used to evaluate the anti-diarrhoeal activity, inhibition of defecation and diarrhoea were determined in mice, effects on castor oil-induced enteropooling, intestinal transit and intestinal fluid secretion in rats or mice. Minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) of FPAE against strains of three clinical bacterial isolates and one reference strain were used to test the anti-microbial activity. The FPAE reduced the frequency of diarrhoea episodes and decreased the propulsion of charcoal meal through the gastrointestinal tract in a dose dependent manner. FPAE (100-500 mg/kg, p.o.) produced dose-dependent and significant (P<0.01) protection of mice against castor oil-induced diarrhoea. FPAE, dose-dependently and significantly (P< 0.01) delayed the onset of castor-oil induced diarrhoea, decreased the frequency of defecation, and reduced the severity of diarrhoea. Compared with control animals, FPAE, dose-dependently and significantly (P< 0.01) decreased the volume of castor oil-induced intestinal fluid secretion, and reduced the number, weight and wetness of faecal droppings. There was no deaths or abnormalities in behaviour seen in the acute toxicity test. The aqueous extract displayed anti-microbial effects to three species of bacteria in anti-microbial test. The findings of this study indicate that FPAE possesses anti-diarrhoeal property in rats and mice and confirm the ethnomedicinal use of Flos Populi as a valuable natural remedy for the treatment, management and/or control of diarrhoea. These results may support the fact that this plant is traditionally used to cure diarrhoea. Crown Copyright © 2013. Published by Elsevier Ireland Ltd. All rights reserved.

Ricinus communis intoxications in human and veterinary medicine-a summary of real cases.

PubMed

Worbs, Sylvia; Köhler, Kernt; Pauly, Diana; Avondet, Marc-André; Schaer, Martin; Dorner, Martin B; Dorner, Brigitte G

2011-10-01

Accidental and intended Ricinus communis intoxications in humans and animals have been known for centuries but the causative agent remained elusive until 1888 when Stillmark attributed the toxicity to the lectin ricin. Ricinus communis is grown worldwide on an industrial scale for the production of castor oil. As by-product in castor oil production ricin is mass produced above 1 million tons per year. On the basis of its availability, toxicity, ease of preparation and the current lack of medical countermeasures, ricin has gained attention as potential biological warfare agent. The seeds also contain the less toxic, but highly homologous Ricinus communis agglutinin and the alkaloid ricinine, and especially the latter can be used to track intoxications. After oil extraction and detoxification, the defatted press cake is used as organic fertilizer and as low-value feed. In this context there have been sporadic reports from different countries describing animal intoxications after uptake of obviously insufficiently detoxified fertilizer. Observations in Germany over several years, however, have led us to speculate that the detoxification process is not always performed thoroughly and controlled, calling for international regulations which clearly state a ricin threshold in fertilizer. In this review we summarize knowledge on intended and unintended poisoning with ricin or castor seeds both in humans and animals, with a particular emphasis on intoxications due to improperly detoxified castor bean meal and forensic analysis.

Ricinus communis Intoxications in Human and Veterinary Medicine-A Summary of Real Cases

PubMed Central

Worbs, Sylvia; Köhler, Kernt; Pauly, Diana; Avondet, Marc-André; Schaer, Martin; Dorner, Martin B.; Dorner, Brigitte G.

2011-01-01

Accidental and intended Ricinus communis intoxications in humans and animals have been known for centuries but the causative agent remained elusive until 1888 when Stillmark attributed the toxicity to the lectin ricin. Ricinus communis is grown worldwide on an industrial scale for the production of castor oil. As by-product in castor oil production ricin is mass produced above 1 million tons per year. On the basis of its availability, toxicity, ease of preparation and the current lack of medical countermeasures, ricin has gained attention as potential biological warfare agent. The seeds also contain the less toxic, but highly homologous Ricinus communis agglutinin and the alkaloid ricinine, and especially the latter can be used to track intoxications. After oil extraction and detoxification, the defatted press cake is used as organic fertilizer and as low-value feed. In this context there have been sporadic reports from different countries describing animal intoxications after uptake of obviously insufficiently detoxified fertilizer. Observations in Germany over several years, however, have led us to speculate that the detoxification process is not always performed thoroughly and controlled, calling for international regulations which clearly state a ricin threshold in fertilizer. In this review we summarize knowledge on intended and unintended poisoning with ricin or castor seeds both in humans and animals, with a particular emphasis on intoxications due to improperly detoxified castor bean meal and forensic analysis. PMID:22069699

Preparation and in vitro evaluation of simvastatin ethosome.

PubMed

An, Keyao; Sun, Yong; Xu, Lisa; Cui, Xiangzhen

2011-12-01

To prepare ethosome loading simvastatin,an orthogonal test was applied to optimize the prescriptions, and the qualities of simvastatin ethosome were characterized by the shape, particle size, encapsulation efficiency (EE), and stability. The formation of 40% (v/v) ethanol, 0.02% (m/v) cholesterol, 2.0% (m/v) soy lecithin, and 5% (m/v) polyoxyethylene hydrogenated castor oil showed the maximal EE (69.3%). We observed the shape of simvastatin ethosome through TEM. The average size of the particles was 52.4 ± 3.24 nm, which was detected by a N5 submicron particle size analyzer. After 120 days storage in 4? and at room temperature, the simvastatin ethosome had no significant change.

Antidiarrhoeal activity of Psidium guajava Linn. (Myrtaceae) leaf aqueous extract in rodents.

PubMed

Ojewole, John A O; Awe, Emmanuel O; Chiwororo, Witness D H

2008-12-01

The leaf of Psidium guajava Linn. (family: Myrtaceae) is used traditionally in African folk medicine to manage, control and/or treat a plethora of human ailments, including diarrhoea. In this study, we examined the antidiarrhoeal activity of Psidium guajava leaf aqueous extract (PGE) on experimentally-induced diarrhoea in rodents. PGE (50-400 mg/kg p.o.) produced dose-dependent and significant (P<0.05-0.01) protection of rats and mice against castor oil-induced diarrhoea, inhibited intestinal transit, and delayed gastric emptying. Like atropine (1 mg/kg, p.o.), PGE produced dose-dependent and significant (P<0.05-0.01) antimotility effect, and caused dose-related inhibition of castor oil-induced enteropooling in the animals. Like loperamide (10 mg/kg, p.o.), PGE dose-dependently and significantly (P<0.05-0.01) delayed the onset of castor oil-induced diarrhoea, decreased the frequency of defaecation, and reduced the severity of diarrhoea in the rodents. Compared with control animals, PGE dose-dependently and significantly (P<0.05-0.01) decreased the volume of castor oil-induced intestinal fluid secretion, and reduced the number, weight and wetness of faecal droppings. PGE also produced concentration-related and significant (P<0.05-0.01) inhibitions of the spontaneous, rhythmic, pendular contractions of the rabbit isolated duodenum. The findings of this study indicate that PGE possesses antidiarrhoeal activity, and thus lend pharmacological credence to the suggested folkloric use of the plant as a natural remedy for the treatment, management and/or control of diarrhoea in some rural communities of southern Africa.

Lubrication properties of new crop oils

USDA-ARS?s Scientific Manuscript database

Oils from new crops such as lesquerella (Lesquerella fendleri), field pennycress (Thlaspi arvense L.), meadowfoam (Limnanthes alba L.), and cuphea PSR-23 (Cuphea viscosissima × Cuphea lanceolata) were investigated and compared with vegetable oils from commodity crops such as castor, corn, and soybea...

Screening of microbes for the production of polyol oils from soybean oil

USDA-ARS?s Scientific Manuscript database

Introduction. More than 30.6 million tons of soybean oil were produced worldwide annually and the major use of this oil is for food products. Triacylglycerols (TAG) containing hydroxy fatty acids (FA), e.g., castor oil, have many industrial uses such as the manufacture of aviation lubricant, plasti...

Influence of fatty acid methyl esters from hydroxylated vegetable oils on diesel fuel lubricity.

PubMed

Goodrum, John W; Geller, Daniel P

2005-05-01

Current and future regulations on the sulfur content of diesel fuel have led to a decrease in lubricity of these fuels. This decreased lubricity poses a significant problem as it may lead to wear and damage of diesel engines, primarily fuel injection systems. Vegetable oil based diesel fuel substitutes (biodiesel) have been shown to be clean and effective and may increase overall lubricity when added to diesel fuel at nominally low levels. Previous studies on castor oil suggest that its uniquely high level of the hydroxy fatty acid ricinoleic acid may impart increased lubricity to the oil and its derivatives as compared to other vegetable oils. Likewise, the developing oilseed Lesquerella may also increase diesel lubricity through its unique hydroxy fatty acid composition. This study examines the effect of castor and Lesquerella oil esters on the lubricity of diesel fuel using the High-Frequency Reciprocating Rig (HFRR) test and compares these results to those for the commercial vegetable oil derivatives soybean and rapeseed methyl esters.

A modified, hypoallergenic variant of the Ricinus communis Ric c1 protein retains biological activity

PubMed Central

Pacheco-Soares, Thaís; de Oliveira Carvalho, André; da Silva Araújo, Jucélia; da Silva de Souza, Giliane; Machado, Olga L.T.

2018-01-01

Ric c1, an allergenic protein from castor oil plants (Ricinus communis), is an insect α-amylase inhibitor that has become an occupational allergen. Ric c1 can cross-react with allergens from wheat, soybean, peanut, shrimp, fish, gluten, house dust, tobacco and air fungus, thereby amplifying the concern and risks caused by castor oil plants (COP) allergens. Two continuous IgE-binding epitopes were identified in Ric c1, both containing glutamic acid residues involved in IgE-binding and allergic challenges. We produced recombinant Ric c1 (rRic c1) in Escherichia coli, using primers from foliar castor oil plant DNA, and a mutant (Glu-Leu) recombinant protein (mrRic c1) in the same system using synthetic genes. rRic c1 preserved both allergenic and α-amylase inhibitory properties, and mrRic c1 drastically reduced allergenic properties. These results can help to establish meaningful relationships between structure, defence and allergenicity, important steps for producing engineered plants and developing new approaches for immunotherapy. PMID:29444820

A Novel Methodology for the Synthesis of Acyloxy Castor Polyol Esters: Low Pour Point Lubricant Base Stocks.

PubMed

Kamalakar, Kotte; Mahesh, Goli; Prasad, Rachapudi B N; Karuna, Mallampalli S L

2015-01-01

Castor oil, a non-edible oil containing hydroxyl fatty acid, ricinoleic acid (89.3 %) was chemically modified employing a two step procedure. The first step involved acylation (C(2)-C(6) alkanoic anhydrides) of -OH functionality employing a green catalyst, Kieselguhr-G and solvent free medium. The catalyst after reaction was filtered and reused several times without loss in activity. The second step is esterification of acylated castor fatty acids with branched mono alcohol, 2-ethylhexanol and polyols namely neopentyl glycol (NPG), trimethylolpropane (TMP) and pentaerythritol (PE) to obtain 16 novel base stocks. The base stocks when evaluated for different lubricant properties have shown very low pour points (-30 to -45°C) and broad viscosity ranges 20.27 cSt to 370.73 cSt, higher viscosity indices (144-171), good thermal and oxidative stabilities, and high weld load capacities suitable for multi-range industrial applications such as hydraulic fluids, metal working fluids, gear oil, forging and aviation applications. The study revealed that acylated branched mono- and polyol esters rich in monounsaturation is desirable for developing low pour point base stocks.

Ratios of regioisomers of minor acylglycerols less polar than triricinolein in castor oil estimated by mass spectrometry and the biosynthesis of tetraacylglycerols in castor

USDA-ARS?s Scientific Manuscript database

We have recently reported the identification of forty new minor molecular species of acylglycerols containing hydroxy fatty acids less polar than triricinolein by electrospray ionization mass spectrometry of the lithium adducts. The ratios of regioisomers of triacylglycerols (ABC and AAB types) and ...

Ricinus communis L. (castor bean) as a potential candidate for revegetating industrial waste contaminated sites in peri-urban Greater Hyderabad: remarks on seed oil.

PubMed

Boda, Ravi Kiran; Majeti, Narasimha Vara Prasad; Suthari, Sateesh

2017-08-01

Ricinus communis L. (castor bean or castor oil plant) was found growing on metal-contaminated sites (4) of peri-urban Greater Hyderabad comprises of erstwhile industrial areas viz Bollaram, Patancheru, Bharatnagar, and Kattedan industrial areas. During 2013-2017, about 60 research papers have appeared focusing the role of castor bean in phytoremediation of co-contaminated soils, co-generation of biomaterials, and environmental cleanup, as bioenergy crop and sustainable development. The present study is focused on its use as a multipurpose phytoremediation crop for phytostabilization and revegetation of waste disposed peri-urban contaminated soils. To determine the plant tolerance level, metal accumulation, chlorophyll, protein, proline, lipid peroxidation, oil content, and soil properties were characterized. It was noticed that the castor plant and soils have high concentration of metals such as cadmium (Cd), lead (Pb), iron (Fe), manganese (Mn), and zinc (Zn). The soils have high phosphorous (P), adequate nitrogen (N), and low concentration of potassium (K). Iron (Fe) concentrations ranged from1672±50.91 to 2166±155.78 mg kg -1 in the soil. The trend of metal accumulation Fe>Zn>Mn>Pb>Cd was found in different plant parts at polluted sites. The translocation of Cd and Pb showed values more than one in industrial areas viz Bollaram, Kattedan, and Bharatnagar indicating the plants resistance to metal toxicity. Chlorophyll and protein content reduced while proline and malondialdehyde increased due to its tolerance level under metal exposure. The content of ricinoleic acid was higher, and the fatty acids composition of polluted areas was almost similar to that of the control area. Thus, R. communis L. can be employed for reclamation of heavy metal contaminated soils.

Effects of pH on protein components of extracted oil bodies from diverse plant seeds and endogenous protease-induced oleosin hydrolysis.

PubMed

Zhao, Luping; Chen, Yeming; Chen, Yajing; Kong, Xiangzhen; Hua, Yufei

2016-06-01

Plant seeds are used to extract oil bodies for diverse applications, but oil bodies extracted at different pH values exhibit different properties. Jicama, sunflower, peanut, castor bean, rapeseed, and sesame were selected to examine the effects of pH (6.5-11.0) on the protein components of oil bodies and the oleosin hydrolysis in pH 6.5-extracted oil bodies. In addition to oleosins, many extrinsic proteins (globulins, 2S albumin, and enzymes) were present in pH 6.5-extracted oil bodies. Globulins were mostly removed at pH 8.0, whereas 2S albumins were removed at pH 11.0. At pH 11.0, highly purified oil bodies were obtained from jicama, sunflower, peanut, and sesame, whereas lipase remained in the castor bean oil bodies and many enzymes in the rapeseed oil bodies. Endogenous protease-induced hydrolysis of oleosins occurred in all selected plant seeds. Oleosins with larger sizes were hydrolysed more quickly than oleosins with smaller sizes in each plant seed. Copyright © 2016 Elsevier Ltd. All rights reserved.

Analysis of Carbohydrate and Fatty Acid Marker Abundance in Ricin Toxin Preparations for Forensic Information

DOE Office of Scientific and Technical Information (OSTI.GOV)

Colburn, Heather A.; Wunschel, David S.; Kreuzer-Martin, Helen W.

2010-07-15

One challenge in the forensic analysis of ricin samples is determining the method and extent of sample preparation. Ricin purification from the source castor seeds is essentially a protein purification through removal of the non-protein fractions of the seed. Two major, non-protein constituents in the seed are the castor oil and carbohydrates. Ricinoleic acid is a relatively unique fatty acid in nature and is the most abundant component of castor oil, which comprises roughly half the seed weight. The carbohydrate component comprises roughly half of the remaining “mash” left after oil and hull removal. We used derivatization of carbohydrate andmore » fatty acid markers followed by identification and quantification using gas chromatography/mass spectrometry (GC/MS) to assess compositional changes in ricin samples purified by different methods. The loss of ricinoleic acid indicated steps for oil removal had occurred. Changes to the carbohydrate content of the sample were also observed following protein precipitation. The differential loss of arabinose relative to mannose indicated removal of the major carbohydrate fraction of the seed and enrichment of the protein content. Taken together, these changes in fatty acid and carbohydrate abundance are indicative of the preparation method used for each sample.« less

Evaluation of the safety and efficacy of Lesquerella fendleri seed and oils as poultry feed additives

USDA-ARS?s Scientific Manuscript database

Lesquerella (Lesquerella fendleri (Gray) Wats) is an oil seed plant capable of growth over a large geographic area of the southwestern U.S. The seed oil contains hydroxyfatty acids, useful in a variety of industrial products, and can replace imported castor bean oil (Ricinus communis L.). Lesquere...

Quantification of TAG and DAG in lesquerella (Physaria fendleri) oil by HPLC and MS

USDA-ARS?s Scientific Manuscript database

Castor oil has many industrial uses because of its high content (90%) of the hydroxy fatty acid, ricinoleic acid (OH1218:19). Lesquerella oil containing lesquerolic acid (Ls, OH1420:111, 56.5%) is potentially useful in industry. Ten diacylglycerols (DAG) and 74 triacylglycerols (TAG) in the seed oil...

Glutathione Preservation during Storage of Rat Lenses in Optisol-GS and Castor Oil

PubMed Central

Holm, Thomas; Brøgger-Jensen, Martin Rocho; Johnson, Leif; Kessel, Line

2013-01-01

Background Glutathione concentration in the lens decreases in aging and cataractous lenses, providing a marker for tissue condition. Experimental procedures requiring unfrozen lenses from donor banks rely on transportation in storage medium, affecting lens homeostasis and alterations in glutathione levels. The aim of the study was to examine the effects of Optisol-GS and castor oil on lens condition, determined from their ability to maintain glutathione concentrations. Methodology/Principal Findings Rat lenses were stored in the two types of storage media at varying time intervals up to 3 days. Glutathione concentration was afterwards determined in an enzymatic detection assay, specific for both reduced and oxidized forms. Lenses removed immediately after death exhibited a glutathione concentration of 4.70±0.29 mM. In vitro stored lenses in Optisol-GS lost glutathione quickly, ending with a concentration of 0.60±0.34 mM after 3 days while castor oil stored lenses exhibited a slower decline and ended at 3 times the concentration. A group of lenses were additionally stored under post mortem conditions within the host for 6 hours before its removal. Total glutathione after 6 hours was similar to that of lenses removed immediately after death, but with altered GSH and GSSG concentrations. Subsequent storage of these lenses in media showed changes similar to those in the first series of experiments, albeit to a lesser degree. Conclusions/Significance It was determined that storage in Optisol-GS resulted in a higher loss of glutathione than lenses stored in castor oil. Storage for more than 12 hours reduced glutathione to half its original concentration, and was considered unusable after 24 hours. PMID:24260265

Kinetic and Thermodynamics studies for Castor Oil Extraction Using Subcritical Water Technology.

PubMed

Abdelmoez, Wael; Ashour, Eman; Naguib, Shahenaz M; Hilal, Amr; Al Mahdy, Dalia A; Mahrous, Engy A; Abdel-Sattar, Essam

2016-06-01

In this work both kinetic and thermodynamics of castor oil extraction from its seeds using subcritical water technique were studied. It was found that the extraction process followed two consecutive steps. In these steps, the oil was firstly extracted from inside the powder by diffusion mechanism. Then the extracted oil, due to extending the extraction time under high temperature and pressure, was subjected to a decomposition reaction following first order mechanism. The experimental data correlated well with the irreversible consecutive unimolecular-type first order mechanism. The values of both oil extraction rate constants and decomposition rate constants were calculated through non-linear fitting using DataFit software. The extraction rate constants were found to be 0.0019, 0.024, 0.098, 0.1 and 0.117 min(-1), while the decomposition rate constants were 0.057, 0.059, 0.014, 0.019 and 0.17 min(-1) at extraction temperatures of 240, 250, 260, 270 and 280°C, respectively. The thermodynamic properties of the oil extraction process were investigated using Arrhenius equation. The values of the activation energy, Ea, and the frequency factor, A, were 73 kJ mol(-1) and 946, 002 min(-1), respectively. The physicochemical properties of the extracted castor oil including the specific gravity, viscosity, acid value, pH value and calorific value were found to be 0.947, 7.487, 1.094 mg KOH/g, 6.1, and 41.5 MJ/Kg, respectively. Gas chromatography analysis showed that ricinoleic acid (83.6%) appears as the predominant fatty acid in the extracted oil followed by oleic acid (5.5%) and linoleic acid (2.3%).

21 CFR 176.200 - Defoaming agents used in coatings.

Code of Federal Regulations, 2011 CFR

2011-04-01

... alcohol tert-Butyl alcohol Butyl stearate Castor oil, sulfated, ammonium, potassium, or sodium salt Cetyl... palmitate Mineral oil Mustardseed oil, sulfated, ammonium, potassium, or sodium salt Myristyl alcohol... hydrocarbons As defined in § 178.3650 of this chapter. Oleic acid, sulfated, ammonium, potassium, or sodium...

21 CFR 176.200 - Defoaming agents used in coatings.

Code of Federal Regulations, 2010 CFR

2010-04-01

... alcohol tert-Butyl alcohol Butyl stearate Castor oil, sulfated, ammonium, potassium, or sodium salt Cetyl... palmitate Mineral oil Mustardseed oil, sulfated, ammonium, potassium, or sodium salt Myristyl alcohol... hydrocarbons As defined in § 178.3650 of this chapter. Oleic acid, sulfated, ammonium, potassium, or sodium...

Metabolic Engineering for Improved Hydroxy Fatty Acid Production in Lesquerella

USDA-ARS?s Scientific Manuscript database

Hydroxy fatty acids (HFA) from plant seed triacylglycerols (TAGs, oil molecule) are wildly used in manufacturing industrial products, such as lubricants, plasticizers and surfactants. Castor oil has 90% HFA which occupies all three sn positions of most TAGs, while lesquerella oil contains 60% HFA mo...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kreuzer, Helen W.; West, Jason B.; Ehleringer, James

Seeds of the castor plant Ricinus communis, also known as castor beans, are of forensic interest because they are the source of the poison ricin. We have tested whether stable isotope ratios of castor seeds and ricin prepared by various methods can be used as a forensic signature. We collected over 300 castor seed samples from locations around the world and measured the C, N, O, and H stable isotope ratios of the whole seeds, oil, and three types of ricin preparations. Our results demonstrate that N isotope ratios can be used to correlate ricin prepared by any of thesemore » methods to source seeds. Further, stable isotope ratios distinguished >99% of crude and purified ricin protein samples in pair-wise comparison tests. Stable isotope ratios therefore constitute a valuable forensic signature for ricin preparations.« less

Pharmacokinetics and pharmacodynamics of injectable testosterone undecanoate in castrated cynomolgus monkeys (Macaca fascicularis) are independent of different oil vehicles.

PubMed

Wistuba, Joachim; Marc Luetjens, C; Kamischke, Axel; Gu, Yi-Qun; Schlatt, Stefan; Simoni, Manuela; Nieschlag, Eberhard

2005-08-01

Testosterone undecanoate (TU) dissolved in soybean oil was developed in China to improve the pharmacokinetics of this testosterone ester in comparison with TU in castor or tea seed oil. As a pre-clinical primate model, three groups of five castrated cynomolgus macaques received either a single intramuscular injection of 10 mg/kg body weight TU in soybean oil, in tea seed oil, or in castor oil (equals 6.3 mg pure T/kg body weight for all preparations). Testosterone, estradiol, luteinizing hormone, and follicle-stimulating hormone as well as prostate volume, body weight and ejaculate weight were evaluated. After injection supraphysiological testosterone levels were induced. There were no significant differences in the pharmacokinetics of the three TU preparations for testosterone and estradiol. The gonadotropin levels showed a high individual variation. Prostate volumes increased equally in all groups after administration and declined to castrate level afterwards. The results suggest that TU in soybean oil produces similar effects as TU in the other vehicles. This study in non-human primates provides no objection to testing of this new preparation in humans.

Biodegradable Photo-Crosslinked Thin Polymer Networks Based on Vegetable Oil Hydroxyfatty Acids

USDA-ARS?s Scientific Manuscript database

Novel crosslinked thin polymer networks based on vegetable oil hydroxyfatty acids (HFAs) were prepared by UV photopolymerization and their mechanical properties were evaluated. Two raw materials, castor oil and 7,10-dihydroxy-8(E)-octadecenoic acid (DOD) were used as sources of mono- and di-HFAs, r...

Influence of MgO on Performance and Emissions of DI Engine using blends of Castor oil

NASA Astrophysics Data System (ADS)

Ganesan, S.; Padmanabhan, s.; Senthil kumar, J.; Polina, Navakanth; Krishna kumar, Sanivada

2017-05-01

With the technological development, the research over alternate fuels is increasing day by day in order to help the upcoming generation with a bright and greener future. In order to preserve the existing petroleum resources for future generation, it is necessary to soon switch to any alternate source which is easily available, renewable as well as environment friendly. In this paper I would like to highlight upon the usage of Diesel, Castor Oil and Nano Particles for a compression ignition engine and study the emission characteristics of this fuel at different mixing ratios and analyze the different levels of residue particles.

Bioplastic from Chitosan and Yellow Pumpkin Starch with Castor Oil as Plasticizer

NASA Astrophysics Data System (ADS)

Hasan, M.; Rahmayani, R. F. I.; Munandar

2018-03-01

This study has been conducted on bioplastic synthesis of chitosan and yellow pumpkin starch (Cucurbita moschata) with castor oil as plasticizer. The purpose of this study is to determine the characteristics of the effect of chitosan and starch composition of pumpkins against solvent absorption, tensile strength and biodegradable. The first stage of the research is the making of bioplastic by blending yellow pumpkin starch, chitosan and castor oil. Further, it tested the absorption capacity of the solvent, tensile strength test, and biodegradable analysis. The optimum absorption capacity of the solvent is obtained on the composition of Pumpkin/Chitosan was 50/50 in H2O and C2H5OH solvent. Meanwhile the optimum absorbency in HCl and NaOH solvents is obtained by 60/40 composition. The characterization of the optimum tensile strength test was obtained on the 40/60 composition of 6.787 ± 0.274 Mpa and the fastest biodegradation test process within 5-10 days occurred in the 50/50 composition. The more chitosan content the higher the value of tensile strength test obtained, while the fastest biodegradation rate occureds in the composition of yellow pumpkin starch and chitosan balanced 50:50.

Potential of castor bean (Ricinus communis L.) for phytoremediation of mine tailings and oil production.

PubMed

Ruiz Olivares, Alejandro; Carrillo-González, Rogelio; González-Chávez, Ma del Carmen A; Soto Hernández, Ramón Marcos

2013-01-15

Bioenergy production combined with phytoremediation has been suggested to help in solving two critical world problems: the gradual reduction of fossil fuels and soil contamination. The aim of this research was to investigate the potential for the use of Ricinus communis L. (castor oil plant) as an energy crop and plant species to remediate metal-polluted sites. This study was performed in mine tailings containing high concentrations of Cu, Zn, Mn, Pb and Cd. Physico-chemical characterization, total, DTPA-extractable and water-soluble metals in rhizospheric tailings heap samples were carried. Metal concentrations in plant tissues and translocation factors (TFs) were also determined. The Ricinus seed-oil content was high between 41 and 64%, seeds from San Francisco site 6 had the highest oil content, while these from site 7 had the lowest. No trend between oil yield vs seed origin site was observed. Seed-oil content was negatively correlated with root concentration of Cu, Zn, Pb and Cd, but no correlation was observed with the extractable-metals. According to its shoot metal concentrations and TFs, castor bean is not a metal accumulator plant. This primary colonizing plant is well suited to cope with the local toxic conditions and can be useful for the stabilization of these residues, and for then decreasing metal bioavailability, dispersion and human health risks on these barren tailings heaps and in the surrounding area. Our work is the first report regarding combined oil production and a phytostabilization role for Ricinus plants in metal mine tailings and may give a new value to suitable metal-polluted areas. Copyright © 2012 Elsevier Ltd. All rights reserved.

40 CFR 721.10297 - Tin, C16-18 and C18-unsatd. fatty acids castor-oil fatty acids complexes.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Tin, C16-18 and C18-unsatd. fatty... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10297 Tin, C16-18 and C18-unsatd... to reporting. (1) The chemical substance identified as tin, C16-18 and C18-unsatd. fatty acids castor...

40 CFR 721.10297 - Tin, C16-18 and C18-unsatd. fatty acids castor-oil fatty acids complexes.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Tin, C16-18 and C18-unsatd. fatty... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10297 Tin, C16-18 and C18-unsatd... to reporting. (1) The chemical substance identified as tin, C16-18 and C18-unsatd. fatty acids castor...

40 CFR 721.10297 - Tin, C16-18 and C18-unsatd. fatty acids castor-oil fatty acids complexes.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Tin, C16-18 and C18-unsatd. fatty... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10297 Tin, C16-18 and C18-unsatd... to reporting. (1) The chemical substance identified as tin, C16-18 and C18-unsatd. fatty acids castor...

Therapeutic effect of Linum usitatissimum (flaxseed/linseed) fixed oil on acute and chronic arthritic models in albino rats.

PubMed

Kaithwas, Gaurav; Majumdar, Dipak K

2010-06-01

The present study was undertaken to assess the activity/anti-inflammatory potential of Linum usitatissimum fixed oil against castor oil-induced diarrhoea, turpentine oil-induced joint oedema, formaldehyde and Complete Freund's Adjuvant (CFA)-induced arthritis in Wistar albino rats. The oil intraperitoneally, significantly inhibited the castor oil-induced diarrhoea and turpentine oil-induced exudative joint oedema in a dose-dependent manner. Significant inhibitory effect of L. usitatissimum fixed oil was observed in formaldehyde-induced proliferative global oedematous arthritis when given intraperitoneally, with significant checking of the serum glutamic oxaloacetic acid transaminase and serum glutamic pyruvic acid transaminase. Further, L. usitatissimum fixed oil showed a significant dose-dependent protective effect against CFA-induced arthritis as well. Secondary lesions produced by CFA due to a delayed hypersensitivity reaction were also reduced in a significant manner. Anti-inflammatory activity of L. usitatissimum fixed oil can be attributed to the presence of alpha linolenic acid (57.38%, an omega-3 fatty acid, 18:3, n-3) having dual inhibitory effect on arachidonate metabolism resulting in suppressed production of proinflammatory n-6 eicosanoids (PGE(2), LTB(4)) and diminished vascular permeability. These observations suggest possible therapeutic potential of L. usitatissimum fixed oil in inflammatory disorders like rheumatoid arthritis.

Laxative overdose

MedlinePlus

Below are specific laxative drugs, with some brand names: Bisacodyl (Dulcolax) Cascara sagrada Castor oil Docusate (Colace) Docusate and phenolphthalein (Correctol) Glycerin suppositories Lactulose (Duphalac) Magnesium ...

Effects of ricinoleic acid esters from castor oil of Ricinus communis on the vitellogenesis of Rhipicephalus sanguineus (Latreille, 1806) (Acari: Ixodidae) ticks.

PubMed

Arnosti, André; Brienza, Paula Desjardins; Furquim, Karim Christina Scopinho; Chierice, Gilberto Orivaldo; Bechara, Gervásio Henrique; Calligaris, Izabela Braggião; Camargo-Mathias, Maria Izabel

2011-02-01

This study examines the effects of ricinoleic acid esters from Ricinus communis castor oil on the vitellogenesis of Rhipicephalus sanguineus ticks attached to hosts that were fed with commercial rabbit food containing these esters. The oocytes of ticks from the treatment group (TG) showed cytoplasmic changes that inhibited the development of oocytes I and II to the advanced stages (IV and V) in addition to preventing the maturation of oocytes V, resulting in small ones. In addition, sperm was not observed in ampoules. Our findings confirm the acaricide potential of ricinoleic acid esters. Copyright © 2010 Elsevier Inc. All rights reserved.

Influence of the reaction conditions on the enzyme catalyzed transesterification of castor oil: A possible step in biodiesel production.

PubMed

Andrade, Thalles A; Errico, Massimiliano; Christensen, Knud V

2017-11-01

The identification of the influence of the reaction parameters is of paramount importance when defining a process design. In this work, non-edible castor oil was reacted with methanol to produce a possible component for biodiesel blends, using liquid enzymes as the catalyst. Temperature, alcohol-to-oil molar ratio, enzyme and added water contents were the reaction parameters evaluated in the transesterification reactions. The optimal conditions, giving the optimal final FAME yield and FFA content in the methyl ester-phase was identified. At 35°C, 6.0 methanol-to-oil molar ratio, 5wt% of enzyme and 5wt% of water contents, 94% of FAME yield and 6.1% of FFA in the final composition were obtained. The investigation was completed with the analysis of the component profiles, showing that at least 8h are necessary to reach a satisfactory FAME yield together with a minor FFA content. Copyright © 2017 Elsevier Ltd. All rights reserved.

A castor oil-containing dental luting agent: effects of cyclic loading and storage time on flexural strength

PubMed Central

DERCELI, Juliana dos Reis; FAIS, Laiza Maria Grassi; PINELLI, Lígia Antunes Pereira

2014-01-01

Favorable results in the use of castor oil polyurethane (COP) as pulp capping, membrane material, sealer, mouthwash and in bone repair, associated with the fact that Ricinus communis is not derived from petroleum and it is abundant in Brazil, encourage researches in the development of luting agents. Objectives This study compared the flexural strength (FS) of a castor oil-containing dental luting agent with a weight percentage of 10% (wt%) of calcium carbonate (COP10) with RelyX ARC (RX) after mechanical cycling (MC) and distilled water storage. Material and Methods Sixty-four specimens (25x2x2 mm) were fabricated and divided into two groups, COP10 and RX (control). Each group was divided into 4 subgroups (n=8) according to the storage time, 24 hours (24 h) or 60 days (60 d), and the performance (MC+FS) or not (only FS) of the mechanical cycling test. The FS (10 kN; 0.5 mm/min) and MC tests (10,000 cycles, 5 Hz, 0.5 mm/min) were carried out using an MTS-810 machine. The data were analyzed using ANOVA (α=0.05). Results The obtained FS (MPa) values were: COP10 24h- 19.04±2.41; COP10 60d- 17.92±3.54; RX 24h- 75.19±3.43; RX 60d- 88.77±6.89. All the RX specimens submitted to MC fractured, while the values for COP10 after MC were as follows: COP10 24h- 17.90±1.87 and COP10 60d- 18.60±1.60. Conclusions A castor oil-containing dental luting agent with a weight percentage of 10% (wt%) of calcium carbonate is resistant to mechanical cycling without decreases in flexural strength. However, mean COP10 showed only about 25% of the RelyX ARC mean flexural strength. PMID:25591018

Preparation methods for monodispersed garlic oil microspheres in water using the microemulsion technique and their potential as antimicrobials.

PubMed

Zheng, Hua Ming; Li, Hou Bin; Wang, Da Wei; Liu, Dun

2013-08-01

Garlic oil is considered as a natural broad-spectrum antibiotic because of its well-known antimicrobial activity. However, the characteristics of easy volatility and poor aqueous solubility limit the application of garlic oil in industry. The purpose of the present work is to develop and evaluate an oil-free microemulsion by loading garlic oil in microemulsion system. Microemulsions were prepared with ethoxylated hydrogenated castor (Cremophor RH40) as surfactant, n-butanol (or ethanol) as cosurfactant, oleic acid-containing garlic oil as oil phase, and ultrapure water as water phase. The effects of the ratio of surfactant to cosurfactant and different oil concentration on the area of oil-in-water (O/W) microemulsion region in pseudoternary phase diagrams were investigated. The particle size and garlic oil encapsulation efficiency of the formed microemulsions with different formulations were also investigated. In addition, the antimicrobial activity in vitro against Escherichia coli and Staphylococcus aureus was assessed. The experimental results show that a stable microemulsion region can be obtained when the mass ratio of surfactant to cosurfactant is, respectively, 1:1, 2:1, and 3:1. Especially, when the mixture surfactants of RH40/n-butanol 2/1 (w/w) is used in the microemulsion formulation, the area of O/W microemulsion region is 0.089 with the particle size 13.29 to 13.85 nm and garlic oil encapsulation efficiency 99.5%. The prepared microemulsion solution exhibits remarkable antibacterial activity against S. aureus. © 2013 Institute of Food Technologists®

Antidiarrhoeal activity of aqueous leaf extract of Caladium bicolor (Araceae) and its possible mechanisms of action.

PubMed

Salako, Olanrewaju A; Akindele, Abidemi J; Shitta, Omotoyosi M; Elegunde, Olajumoke O; Adeyemi, Olufunmilayo O

2015-12-24

Caladium bicolor (Araceae) is a horticulture plant also used by some traditional medicine practitioners in the treatment of diarrhoea and other gastrointestinal disorders. This study was conducted to evaluate the antidiarrhoeal activity of the aqueous leaf extract of C. bicolor and its possible mechanisms of action in rodents. Normal and castor oil-induced intestinal transit and castor oil-induced diarrhoea tests were carried out in mice while gastric emptying and enteropooling tests were conducted in rats following the administration of distilled water (10 ml/kg, p.o.), C. bicolor extract (1-50mg/kg, p.o.) and loperamide (5mg/kg, p.o.). The probable mechanisms of action of C. bicolor was investigated following pre-treatment with yohimbine (10mg/kg, s.c.; α2-adrenoceptor antagonist), pilocarpine (1mg/kg, s.c.; non-selective muscarinic receptor agonist), prazosin (1mg/kg, s.c.; α1-adrenoceptor antagonist) and propranolol (1mg/kg, i.p.; non-selective β-adrenoceptor antagonist) 15 min prior to administration of C. bicolor extract (50mg/kg, p.o.). After 30 min of pre-treatment with these drugs, the mice were subjected to the castor oil-induced intestinal transit test. C. bicolor extract did not produce significant (p>0.05) effect on normal intestinal transit unlike loperamide which caused significant (p<0.001) inhibition (61.57%). The extract caused significant (p<0.001) dose-dependent inhibition of castor oil-induced intestinal transit with peak effect, 100% inhibition, elicited at the dose of 50mg/kg compared to 86.97% inhibition for loperamide. Yohimbine and pilocarpine most significantly (p<0.001) reversed this effect of the extract. In the castor oil-induced diarrhoea test, the extract (1mg/kg) and loperamide significantly (p<0.05, 0.01) delayed the onset of diarrhoea. For diarrhoea score, the extract (1 and 50mg/kg) inhibited diarrhoea development (47.53% and 43.83% inhibition, respectively) like loperamide (5mg/kg; 54.94%). The in vivo antidiarrhoeal index of the extract at 1 and 50mg/kg was 50.07% and 42.81% respectively compared to 58.15% for loperamide. The results obtained in this study suggest that the aqueous leaf extract of C. bicolor possess antidiarrhoeal activity due to its anti-motility effect possibly via antagonist action on intestinal muscarinic receptors and agonist action on intestinal α2-adrenoceptors. This justifies the use of the extract in traditional medicine for the treatment of diarrhoea. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Bio-aviation fuel production from hydroprocessing castor oil promoted by the nickel-based bifunctional catalysts.

PubMed

Liu, Siyang; Zhu, Qingqing; Guan, Qingxin; He, Liangnian; Li, Wei

2015-05-01

Bio-aviation fuel was firstly synthesized by hydroprocessing castor oil in a continuous-flow fixed-bed microreactor with the main objective to obtain the high yield of aviation fuel and determine the elemental compositions of the product phases as well as the reaction mechanism. Highest aviation range alkane yields (91.6 wt%) were achieved with high isomer/n-alkane ratio (i/n) 4.4-7.2 over Ni supported on acidic zeolites. In addition, different fuel range alkanes can be obtained by adjusting the degree of hydrodeoxygenation (HDO) and hydrocracking. And the observations are rationalized by a set of reaction pathways for the various product phases. Copyright © 2015 Elsevier Ltd. All rights reserved.

Antidiarrhoeal activity of leaf methanolic extract of Rauwolfia serpentina.

PubMed

Ezeigbo, I I; Ezeja, M I; Madubuike, K G; Ifenkwe, D C; Ukweni, I A; Udeh, N E; Akomas, S C

2012-06-01

To evaluate the antidiarrhoeal property of methanol extract of the leaves of Rauwolfia serpentina (R. serpentina) in experimental diarrhoea induced by castor oil in mice. Doses of 100, 200 and 400 mg/kg R. serpentina leaf methanol extracts were administered to castor oil induced diarrhoea mice to determine its antidiarrhoeal activity. All doses of the extract and the reference drug atropine sulphate (3 mg/kg, i.p.) produced a dose-dependent reduction in intestinal weight and fluid volume. The extracts also significantly reduced the intestinal transit in charcoal meal test when compared to diphenoxylate Hcl (5 mg/kg, p.o.). The results show that the extract of R. serpentina leaves has a significant antidiarrhoeal activity and supports its traditional uses in herbal medicine.

Quantitative proteomics of seed filling in castor: comparison with soybean and rapeseed reveals differences between photosynthetic and nonphotosynthetic seed metabolism.

PubMed

Houston, Norma L; Hajduch, Martin; Thelen, Jay J

2009-10-01

Seed maturation or seed filling is a phase of development that plays a major role in the storage reserve composition of a seed. In many plant seeds photosynthesis plays a major role in this process, although oilseeds, such as castor (Ricinus communis), are capable of accumulating oil without the benefit of photophosphorylation to augment energy demands. To characterize seed filling in castor, a systematic quantitative proteomics study was performed. Two-dimensional gel electrophoresis was used to resolve and quantify Cy-dye-labeled proteins expressed at 2, 3, 4, 5, and 6 weeks after flowering in biological triplicate. Expression profiles for 660 protein spot groups were established, and of these, 522 proteins were confidently identified by liquid chromatography-tandem mass spectrometry by mining against the castor genome. Identified proteins were classified according to function, and the most abundant groups of proteins were involved in protein destination and storage (34%), energy (19%), and metabolism (15%). Carbon assimilatory pathways in castor were compared with previous studies of photosynthetic oilseeds, soybean (Glycine max) and rapeseed (Brassica napus). These comparisons revealed differences in abundance and number of protein isoforms at numerous steps in glycolysis. One such difference was the number of enolase isoforms and their sum abundance; castor had approximately six times as many isoforms as soy and rapeseed. Furthermore, Rubisco was 11-fold less prominent in castor compared to rapeseed. These and other differences suggest some aspects of carbon flow, carbon recapture, as well as ATP and NADPH production in castor differs from photosynthetic oilseeds.

Acute toxicity study of tilmicosin-loaded hydrogenated castor oil-solid lipid nanoparticles.

PubMed

Xie, Shuyu; Wang, Fenghua; Wang, Yan; Zhu, Luyan; Dong, Zhao; Wang, Xiaofang; Li, Xihe; Zhou, Wenzhong

2011-11-20

Our previous studies demonstrated that tilmicosin-loaded hydrogenated castor oil solid lipid nanoparticles (Til-HCO-SLN) are a promising formulation for enhanced pharmacological activity and therapeutic efficacy in veterinary use. The purpose of this work was to evaluate the acute toxicity of Til-HCO-SLN. Two nanoparticle doses were used for the study in ICR mice. The low dose (766 mg/kg.bw) with tilmicosin 7.5 times of the clinic dosage and below the median lethal dose (LD(50)) was subcutaneously administered twice on the first and 7th day. The single high dose (5 g/kg.bw) was the practical upper limit in an acute toxicity study and was administered subcutaneously on the first day. Blank HCO-SLN, native tilmicosin, and saline solution were included as controls. After medication, animals were monitored over 14 days, and then necropsied. Signs of toxicity were evaluated via mortality, symptoms of treatment effect, gross and microscopic pathology, and hematologic and biochemical parameters. After administration of native tilmicosin, all mice died within 2 h in the high dose group, in the low dose group 3 died after the first and 2 died after the second injections. The surviving mice in the tilmicosin low dose group showed hypoactivity, accelerated breath, gloomy spirit and lethargy. In contrast, all mice in Til-HCO-SLN and blank HCO-SLN groups survived at both low and high doses. The high nanoparticle dose induced transient clinical symptoms of treatment effect such as transient reversible action retardation, anorexy and gloomy spirit, increased spleen and liver coefficients and decreased heart coefficients, microscopic pathological changes of liver, spleen and heart, and minor changes in hematologic and biochemical parameters, but no adverse effects were observed in the nanoparticle low dose group. The results revealed that the LD50 of Til-HCO-SLN and blank HCO-SLN exceeded 5 g/kg.bw and thus the nanoparticles are considered low toxic according to the toxicity categories of chemicals. Moreover, HCO-SLN significantly decreased the toxicity of tilmicosin. Normal clinic dosage of Til-HCO-SLN is safe as evaluated by acute toxicity.

Acute toxicity study of tilmicosin-loaded hydrogenated castor oil-solid lipid nanoparticles

PubMed Central

2011-01-01

Background Our previous studies demonstrated that tilmicosin-loaded hydrogenated castor oil solid lipid nanoparticles (Til-HCO-SLN) are a promising formulation for enhanced pharmacological activity and therapeutic efficacy in veterinary use. The purpose of this work was to evaluate the acute toxicity of Til-HCO-SLN. Methods Two nanoparticle doses were used for the study in ICR mice. The low dose (766 mg/kg.bw) with tilmicosin 7.5 times of the clinic dosage and below the median lethal dose (LD50) was subcutaneously administered twice on the first and 7th day. The single high dose (5 g/kg.bw) was the practical upper limit in an acute toxicity study and was administered subcutaneously on the first day. Blank HCO-SLN, native tilmicosin, and saline solution were included as controls. After medication, animals were monitored over 14 days, and then necropsied. Signs of toxicity were evaluated via mortality, symptoms of treatment effect, gross and microscopic pathology, and hematologic and biochemical parameters. Results After administration of native tilmicosin, all mice died within 2 h in the high dose group, in the low dose group 3 died after the first and 2 died after the second injections. The surviving mice in the tilmicosin low dose group showed hypoactivity, accelerated breath, gloomy spirit and lethargy. In contrast, all mice in Til-HCO-SLN and blank HCO-SLN groups survived at both low and high doses. The high nanoparticle dose induced transient clinical symptoms of treatment effect such as transient reversible action retardation, anorexy and gloomy spirit, increased spleen and liver coefficients and decreased heart coefficients, microscopic pathological changes of liver, spleen and heart, and minor changes in hematologic and biochemical parameters, but no adverse effects were observed in the nanoparticle low dose group. Conclusions The results revealed that the LD50 of Til-HCO-SLN and blank HCO-SLN exceeded 5 g/kg.bw and thus the nanoparticles are considered low toxic according to the toxicity categories of chemicals. Moreover, HCO-SLN significantly decreased the toxicity of tilmicosin. Normal clinic dosage of Til-HCO-SLN is safe as evaluated by acute toxicity. PMID:22098626

Castor Oil Based Polyurethanes: Synthesis and Characterization

NASA Astrophysics Data System (ADS)

Macalino, AD; Salen, VA; Reyes, LQ

2017-09-01

In this study, polyurethanes based on castor oil and 1,6-hexamethylene diisocyanate (HMDI) were synthesized with varying weight ratio of the castor oil and HMDI. The formation of urethane linkages was verified through the use of a fourier transform infrared spectroscopy (FTIR). The hydrophilicity of the films was evaluated through the use of a contact angle meter and it was found that the contact angle of all the films were below 90 degrees which confirms their hydrophilicity. The thermal stability of the PU films were studies through the use of a thermal gravimetric analyzer and found that all of the polyurethane films exhibited two weight loss events at elevated temperatures wherein the first weight loss event was observed to occur at 285°C to 384°C while the second weight loss event was observed at around 521°C to 551°C. The hardness, elastic modulus, and tensile elongation of the PU films were determined by using a universal testing machine (UTM) where it was found out that the hardness and the elastic modulus of the film is directly proportional with HMDI loading while the tensile elongation is inversely proportional to it. Lastly, it was known through the swelling studies of the PU films that it does not swell, this is due to the presence of unreacted triglycerides in the material, which prevents water from permeating to the films.

21 CFR 177.1200 - Cellophane.

Code of Federal Regulations, 2011 CFR

2011-04-01

.... Castor oil, sulfonated, sodium salt Cellulose acetate butyrate Cellulose acetate propionate Cetyl alcohol... trimethylenediamine (alkyl C16 to C18) Oleic acid, sulfonated, sodium salt Oleyl palmitamide N,N′-Oleoyl...

Determination of fatty acid methyl esters in cosmetic castor oils by flow injection - electrospray ionization - high resolution mass spectrometry.

PubMed

Arroyo Negrete, Missael Antonio; Wrobel, Kazimierz; Acevedo Aguilar, Francisco Javier; Yanez Barrientos, Eunice; Corrales Escobosa, Alma Rosa; Wrobel, Katarzyna

2018-05-09

The goal of this work was to set up a high throughput procedure for the determination of fatty acid methyl esters (FAMEs) in cosmetic castor oils using flow injection - electrospray ionization - high resolution mass spectrometry, and to demonstrate the need of such analysis for the quality control purposes. The sample aliquot was mixed with isooctane:chloroform (1:1) and submitted to transesterification; the obtained FAMEs were appropriately diluted using water:isopropanol:acetonitrile (20:50:30) with addition of sodium formate which served as an internal standard, lock mass calibrant and promoted the formation of sodium adducts during electrospray ionization (ESI). The principle of flow injection analysis (FIA) was applied for sample introduction to an ESI - quadrupole- time of flight mass spectrometer (ESI-QTOFMS). The carrier solution was composed of water:isopropanol:acetonitrile (20:50:30). From the acquired MS data, flowgrams of the extracted [M+Na] + ions were obtained using the following m/z values for individual FAMEs: 293.2451 (C16:0); 315.2295 (C18:3); 317.2451 (C18:2); 319.2608 (C18:1); 321.2764 (C18:0); 335.2557 (C18:1,OH); 349.3077 (C20:0); 377.3390 (C22:0) and m/z 226.9515 for IS. Baseline-subtracted and filtered signals were integrated and the list of peaks intensities was exported to Excel, where calibration functions were obtained and quantification carried out. Gas chromatography with a flame ionization detector (GC-FID) was used as an alternative analytical tool. The calibration detection limits for FAMEs of unsaturated fatty acids were in the range 3.61 - 8.62 μg L -1 and for saturated compounds in the range 8.51 - 82.4 μg L -1 . The results obtained for commercial were in good agreement with GC-FID data; among nine cosmetic oils analyzed, three contained low concentrations of ricinoleic acid (C18:1, OH), indicating adulteration of castor bean oil with other vegetable oils. Application of FIA for the sample introduction to ESI-QTOFMS enabled for reliable determination of FAMEs in cosmetic oils with sampling frequency of thirty per hour as compared to two samples per hour achievable using GC-FID. The proposed procedure is especially well suited for FAMEs of unsaturated fatty acids that are primary components of castor triacylglycerides, and contribute to desirable properties of any cosmetic oil. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Antidiarrhoeal activity of leaf methanolic extract of Rauwolfia serpentina

PubMed Central

Ezeigbo, II; Ezeja, MI; Madubuike, KG; Ifenkwe, DC; Ukweni, IA; Udeh, NE; Akomas, SC

2012-01-01

Objective To evaluate the antidiarrhoeal property of methanol extract of the leaves of Rauwolfia serpentina (R. serpentina) in experimental diarrhoea induced by castor oil in mice. Methods Doses of 100, 200 and 400 mg/kg R. serpentina leaf methanol extracts were administered to castor oil induced diarrhoea mice to determine its antidiarrhoeal activity. Results All doses of the extract and the reference drug atropine sulphate (3 mg/kg, i.p.) produced a dose-dependent reduction in intestinal weight and fluid volume. The extracts also significantly reduced the intestinal transit in charcoal meal test when compared to diphenoxylate Hcl (5 mg/kg, p.o.). Conclusions The results show that the extract of R. serpentina leaves has a significant antidiarrhoeal activity and supports its traditional uses in herbal medicine. PMID:23569944

Studies on biodegradable and crosslinkable poly(castor oil fumarate)/poly(propylene fumarate) composite adhesive as a potential injectable biomaterial.

PubMed

Mitha, M K; Jayabalan, M

2009-12-01

Biodegradable hydroxyl terminated-poly(castor oil fumarate) (HT-PCF) and poly(propylene fumarate) (HT-PPF) resins were synthesized as an injectable and in situ-cross linkable polyester resins for orthopedic applications. An injectable adhesive formulation containing this resin blend, N-vinyl pyrrolidone (NVP), hydroxy apatite, free radical initiator and accelerator was developed. The Composite adhesives containing the ratio of resin blend and NVP, 2.1:1.5, 2.1:1.2 and 2.1:1.0 set fast with tolerable exothermic temperature as a three dimensionally cross linked toughened material. Crosslink density and mechanical properties of the crosslinked composite increase with increase of NVP. The present crosslinked composite has hydrophilic character and cytocompatibility with L929 fibroblast cells.

Lesquerella seed yield estimation using color image segmentation to track flowering dynamics under water and nitrogen limitation

USDA-ARS?s Scientific Manuscript database

Seed oil from lesquerella (Physaria fendleri (Gray) O'Kane & Al-Shehbaz) can potentially supplement castor oil as a non-petroleum-based chemical feedstock in the production of many industrial products. However, before lesquerella will become commercially viable, further efforts are needed to address...

Mining lesquerella seed transcriptome for oil and meal improvement and translational research

USDA-ARS?s Scientific Manuscript database

Lesquerella (Physaria fendleri), a member of the Brassicaceae family, is currently being developed as a new industrial oilseed. Lesquerella is valued for its unusual hydroxy fatty acid (HFA) lesquerolic acid (20:1OH). The conventional source of HFA is ricinoleic acid (18:1OH) from castor oil. Ricino...

Phase-transfer catalysis and ultrasonic waves II: saponification of vegetable oil.

PubMed

Entezari, M H; Keshavarzi, A

2001-07-01

Saponification of oils which is a commercially important heterogeneous reaction, can be speeded up by the application of ultrasound in the presence of phase-transfer catalyst (PTC). This paper focuses on the ability of ultrasound to cause efficient mixing of this liquid-liquid heterogeneous reaction. Castor oil was taken as a model oil and the kinetic of the reaction was followed by the extent of saponification. The hydrolysis of castor oil was carried out with different PTC such as cetyl trimethyl ammonium bromide (CTAB), benzyl triethyl ammonium chloride (BTAC) and tetrabutyl ammonium bromide (TBAB) in aqueous alkaline solution. As hydroxyl anion moves very slowly from aqueous to oil phase, the presence of a PTC is of prime importance. For this purpose, cationic surfactants are selected. The sonication of biphasic system were performed by 20 kHz (simple horn and cup horn) and 900 kHz. It was found that CTAB was better than the two others and this could be related to the molecular structure of the PTCs. The effect of temperature was also studied on the saponification process. By increasing the temperature, the yield was also increased and this could be explained by intermolecular forces, interfacial tension and mass transfer. Saponification of three different vegetable oils shows that the almond oil is saponified easier than the two others and this could be related to their properties such as surface tension, viscosity and density.

Synthesis and characterization of triglyceride based thermosetting polymers

NASA Astrophysics Data System (ADS)

Can, Erde

2005-07-01

Plant oils, which are found in abundance in all parts of the world and are easily replenished annually, have the potential to replace petroleum as a chemical feedstock for making polymers. Within the past few years, there has been growing interest to use triglycerides as the basic constituent of thermosetting polymers with the necessary rigidity, strength and glass transition temperatures required for engineering applications. Plant oils are not polymerizable in their natural form, however various functional groups that can polymerize can easily be attached to the triglyceride structure making them ideal cross-linking monomers for thermosetting liquid molding resins. Through this research project a number of thermosetting liquid molding resins based on soybean and castor oil, which is a specialty oil with hydroxyls on its fatty acids, have been developed. The triglyceride based monomers were prepared via the malination of the alcoholysis products of soybean and castor oil with various polyols, such as pentaerythritol, glycerol, and Bisphenol A propoxylate. The malinated glycerides were then cured in the presence of a reactive diluent, such as styrene, to form rigid glassy materials with a wide range of properties. In addition to maleate half-esters, methacrylates were also introduced to the glyceride structure via methacrylation of the soybean oil glycerolysis product with methacrylic anhydride. This product, which contains methacrylic acid as by-product, and its blends with styrene also gave rigid materials when cured. The triglyceride based monomers were characterized via conventional spectroscopic techniques. Time resolved FTIR analysis was used to determine the curing kinetics and the final conversions of polymerization of the malinated glyceride-styrene blends. Dynamic Mechanical Analysis (DMA) was used to determine the thermomechanical behavior of these polymers and other mechanical properties were determined via standard mechanical tests. The use of lignin, another renewable resource, as a filler and its effects on the mechanical properties of the polymers based on soybean oil pentaerythritol glyceride maleates and styrene (SOPERMA) was also explored. These novel soybean and castor oil based thermosetting resins show comparable properties to those of commercially successful unsaturated polyester resins and show promise as an alternative to replace these completely petroleum based materials.

Antidiarrhoeal Activity of Hydroethanolic Leaf Extract of Bryophyllum pinnatum Lam. Kurtz (Crassulaceae).

PubMed

Adeyemi, Olufunmilayo O; Ishola, Ismail O; Okoro, Uzodinma

2013-01-01

Bryophyllum pinnatum Lam. Kurtz (Crassulaceae) is used in traditional African medicine in the treatment of diarrhoea. To investigate the antidiarrhoeal action of the hydroethanolic leaf extract of Bryophyllum pinnatum (BP). Normal intestinal transit, castor oil-induced intestinal transit, castor oil-induced diarrhoea, gastric emptying and enteropooling models in rodents were used to investigate antidiarrhoeal effect. The possible mechanism of antidiarrhoeal activity was investigated using prazosin (1 mg/kg, s.c; α1, adrenoceptor antagonist), yohimbine (1 mg/kg, s.c; α2 adrenoceptor antagonist), propranolol (1 mg/kg, i.p; α- adrenoceptor non-selective antagonist), atropine (1 mg/kg, s.c; muscarinic cholinergic antagonist), pilocarpine (1 mg/kg, s.c; muscarinic cholinergic agonist), and isosorbide dinitrate (IDN) (150 mg/kg, p.o; nitric oxide donor). BP (25-100 mg/kg, p.o) produced dose-dependent and significant (P < 0.001) decrease in intestinal propulsion in normal and castor oil-induced intestinal transit models in comparison to distilled water (10 ml/kg, p.o.) treated control. This antidiarrhoeal effect was inhibited by propranolol pretreatment but yohimbine, prazosin, or atropine pretreatment failed to block this effect. BP treatment reduced the increased peristaltic activity induced by pilocarpine, however, co-treatment with IDN significantly (P < 0.001) enhanced the antidiarrhoeal effect of the extract. In castor oil-induced diarrhoea test, the extract produced a dose-dependent and significant (P < 0.001) increase in onset of diarrhoea, decreased diarrhoea score, the number and weight of wet stools when compared to control. The in vivo antidiarrhoeal index (ADI(in) vivo)) of 53.52 produced by the extract (50 mg/kg, p.o.) was similar to 76.28 ADI(in vivo) produced by morphine (10 mg/kg, s.c.). The extract produced dose- dependent and significant (P < 0.05; P < 0.001) decrease in the weight and volume of intestinal content in the intestinal fluid accumulation model. In gastric emptying test, BP treatment reduced the quantity of test meal emptied in 1 h but not significant. The results showed that the hydroethanolic leaf extract of Bryophyllum pinnatum possesses antidiarrhoeal activity possibly mediated by interaction with β adrenoceptor, muscarinic cholinergic receptor and nitric oxide pathway.

VERUCLAY – a new type of photo-adsorbent active in the visible light range: modification of montmorillonite surface with organic surfactant

EPA Science Inventory

Montmorillonite K10 was treated with VeruSOL-3, a biodegradable and food-grade surfactant mixture of coconut oil, castor oil and citrus extracts, to manufacture a benign catalytic adsorbent that is active in the visible light. Veruclay was characterized by SEM, XRD, TGA, UVDRS, a...

Rhipicephalus sanguineus (Acari: Ixodidae) female ticks exposed to castor oil (Ricinus communis): an ultrastructural overview.

PubMed

Sampieri, B R; Furquim, K C S; Nunes, P H; Camargo-Mathias, M I

2013-02-01

Tick control has been accomplished through the use of synthetic acaricides, which has created resistant individuals, as well as contaminating the environment and nontarget organisms. Substances of plant origin, such as oils and extracts of eucalyptus and neem leaves, have been researched as an alternative to replace the synthetic acaricides. Ricinoleic acid esters from castor oil have recently been shown as a promising alternative in eliminating bacterial contamination during ethanol fermentation, by acting as an effective biocide. The same positive results have been observed when these esters are added to the food given to tick-infested rabbits. This study tested the effect of these substance on the reproductive system of Rhipicephalus sanguineus females, added to rabbit food, more specifically on oogenesis. For this, four groups were established: four control groups (CG1, CG2, CG3, and CG4) and four treatment groups (TG1, TG2, TG3, and TG4) with one rabbit in each (New Zealand White), used as hosts. After full 4 days feeding (semi-engorgement), the females were collected and had their ovaries extracted. In this study, it was observed that R. sanguineus females exposed to esters had their ovaries modified, which was demonstrated through transmission electron microscopy techniques. The addition of ricinoleic esters to the diet of tick-infested rabbits revealed how toxic such substances are for the cytoplasmic organelles of oocytes and pedicel cells. These compounds can change the morphophysiology of germ and somatic cells, consequently influencing their viability and, therefore, confirming that the ricinoleic acid esters from castor oil are a promising substance in the control of R. sanguineus.

WRINKLED1 Rescues Feedback Inhibition of Fatty Acid Synthesis in Hydroxylase-Expressing Seeds1[OPEN

PubMed Central

Browse, John

2016-01-01

Previous attempts at engineering Arabidopsis (Arabidopsis thaliana) to produce seed oils containing hydroxy fatty acids (HFA) have resulted in low yields of HFA compared with the native castor (Ricinus communis) plant and caused undesirable effects, including reduced total oil content. Recent studies have led to an understanding of problems involved in the accumulation of HFA in oils of transgenic plants, which include metabolic bottlenecks and a decrease in the rate of fatty acid synthesis. Focusing on engineering the triacylglycerol assembly mechanisms led to modest increases in the HFA content of seed oil, but much room for improvement still remains. We hypothesized that engineering fatty acid synthesis in the plastids to increase flux would facilitate enhanced total incorporation of fatty acids, including HFA, into seed oil. The transcription factor WRINKLED1 (WRI1) positively regulates the expression of genes involved in fatty acid synthesis and controls seed oil levels. We overexpressed Arabidopsis WRI1 in seeds of a transgenic line expressing the castor fatty acid hydroxylase. The proportion of HFA in the oil, the total HFA per seed, and the total oil content of seeds increased to an average of 20.9%, 1.26 µg, and 32.2%, respectively, across five independent lines, compared with 17.6%, 0.83 µg, and 27.9%, respectively, for isogenic segregants. WRI1 and WRI1-regulated genes involved in fatty acid synthesis were up-regulated, providing for a corresponding increase in the rate of fatty acid synthesis. PMID:27208047

Evaluation of Organogel Nanoparticles as Drug Delivery System for Lipophilic Compounds.

PubMed

Martin, Baptiste; Brouillet, Fabien; Franceschi, Sophie; Perez, Emile

2017-05-01

The purpose of the study was to evaluate organogel nanoparticles as a drug delivery system by investigating their stability, according to the formulation strategy, and their release profile. The gelled nanoparticles were prepared by hot emulsification (above the gelation temperature) of an organogel in water, and cooling at room temperature. In the first step, we used DLS and DSC to select the most suitable formulations by optimizing the proportion of ingredients (HSA, PVA, castor oil) to obtain particles of the smallest size and greatest stability. Then, two lipophilic drug models, indomethacin and ketoconazole were entrapped in the nanoparticles made of castor oil gelled by 12-hydroxystearic acid. Thermal studies (DSC) confirmed that there was no significant alteration of gelling due to the entrapped drugs, even at 3% w/w. Very stable dispersions were obtained (>3 months), with gelled oil nanoparticles presenting a mean diameter between 250 and 300 nm. High encapsulation efficiency (>98%) was measured for indomethacin and ketoconazole. The release profile determined by in vitro dialysis showed an immediate release of the drug from the organogel nanoparticles, due to rapid diffusion. The study demonstrates the interest of these gelled oil nanoparticles for the encapsulation and the delivery of lipophilic active compounds.

Lipase production in solid-state fermentation monitoring biomass growth of aspergillus niger using digital image processing.

PubMed

Dutra, Júlio C V; da C Terzi, Selma; Bevilaqua, Juliana Vaz; Damaso, Mônica C T; Couri, Sônia; Langone, Marta A P; Senna, Lilian F

2008-03-01

The aim of this study was to monitor the biomass growth of Aspergillus niger in solid-state fermentation (SSF) for lipase production using digital image processing technique. The strain A. niger 11T53A14 was cultivated in SSF using wheat bran as support, which was enriched with 0.91% (m/v) of ammonium sulfate. The addition of several vegetable oils (castor, soybean, olive, corn, and palm oils) was investigated to enhance lipase production. The maximum lipase activity was obtained using 2% (m/m) castor oil. In these conditions, the growth was evaluated each 24 h for 5 days by the glycosamine content analysis and digital image processing. Lipase activity was also determined. The results indicated that the digital image process technique can be used to monitor biomass growth in a SSF process and to correlate biomass growth and enzyme activity. In addition, the immobilized esterification lipase activity was determined for the butyl oleate synthesis, with and without 50% v/v hexane, resulting in 650 and 120 U/g, respectively. The enzyme was also used for transesterification of soybean oil and ethanol with maximum yield of 2.4%, after 30 min of reaction.

Lipase Production in Solid-State Fermentation Monitoring Biomass Growth of Aspergillus niger Using Digital Image Processing

NASA Astrophysics Data System (ADS)

Dutra, Julio C. V.; da Terzi, Selma C.; Bevilaqua, Juliana Vaz; Damaso, Mônica C. T.; Couri, Sônia; Langone, Marta A. P.; Senna, Lilian F.

The aim of this study was to monitor the biomass growth of Aspergillus niger in solid-state fermentation (SSF) for lipase production using digital image processing technique. The strain A. niger 11T53A14 was cultivated in SSF using wheat bran as support, which was enriched with 0.91% (m/v) of ammonium sulfate. The addition of several vegetable oils (castor, soybean, olive, corn, and palm oils) was investigated to enhance lipase production. The maximum lipase activity was obtained using 2% (m/m) castor oil. In these conditions, the growth was evaluated each 24 h for 5 days by the glycosamine content analysis and digital image processing. Lipase activity was also determined. The results indicated that the digital image process technique can be used to monitor biomass growth in a SSF process and to correlate biomass growth and enzyme activity. In addition, the immobilized esterification lipase activity was determined for the butyl oleate synthesis, with and without 50% v/v hexane, resulting in 650 and 120 U/g, respectively. The enzyme was also used for transesterification of soybean oil and ethanol with maximum yield of 2.4%, after 30 min of reaction.

LDPE/PHB blends filled with castor oil cake

NASA Astrophysics Data System (ADS)

Burlein, Gustavo A.; Rocha, Marisa C. G.

2015-05-01

The response surface methodology (RSM) is a collection of mathematical techniques useful for developing, improving and optimizing process. In this study, RSM technique was applied to evaluate the effect of the components proportion on the mechanical properties of low density polyethylene (LDPE)/ poly (3-hydroxy-butyrate) (PHB) blends filled with castor oil cake (CC). The blends were prepared by melt mixing in a twin screw extruder. Low density polyethylene, poly (3-hydroxy-butyrate) and castor oil pressed cake were represented by the input variables designated as LDPE, PHB and CC, respectively. As it was desirable to consider the largest LDPE content in the ternary system, the components of the mixture were subjected to the following constraints: 0.7 ≤ LDPE ≤ 1.0, 0≤ PHB≤0.3 e 0 ≤ CC ≤0.3. The mechanical properties of the different mixtures were determined by conventional ASTM tests and were evaluated through analysis of variance performed by the Minitab software. Some polynomial equations were tested in order to describe the mechanical behavior of the samples. The quadratic model in pseudo components was selected for describing the tensile behavior because it was the most efficient from a statistical point of view (p-value ≤ 0.05; coefficient of determination (r2) close to 1 and variation inflation factor (VIF) values < 5). The results showed that the LDPE Young's modulus increases but the other tensile properties and impact resistance deteriorate with the addition of PHB or CC. The tensile strength values of binary mixtures of LDPE lie in the range from 8.9 to 10 MPa. As some commercial grades of LDPE have mechanical strength in this range, it may be inferred that the addition of a certain amount of PHB or CC to LDPE may be considered as a possibility for obtaining LDPE based materials with increased susceptibility to biodegradation. The cubic model in pseudo components was selected for describe the flexural strength of the samples because it was the most adequate from a statistical point of view. However, the linear model in pseudo components was the most efficient to describe the flexural modulus of the samples. The results obtained show that superior LDPE flexural properties may be obtained by the addition of PHB or castor oil cake to LDPE. The morphological study of the materials obtained showed that LDPE/PHB blends are immiscible and form morphological structures with well distinguished phase boundaries between dispersed phase and matrix. Biodegradation was evaluated burying the samples in simulated soil for different periods of time. The LDPE/PHB/CC mixtures with higher content of PHB showed more pronounced degradation. Under the experimental conditions studied the LDPE/CC compositions presented no degradation. However, the loss of mass of the LDPE/PHB/CC mixtures was higher than the loss of mass of the corresponding LDPE/PHB binary blend. This result suggests that the castor oil cake accelerates the degradation of the LDPE/PHB blends.

Toxicity of water-soluble fractions of biodiesel fuels derived from castor oil, palm oil, and waste cooking oil.

PubMed

Leite, Maria Bernadete Neiva Lemos; de Araújo, Milena Maria Sampaio; Nascimento, Iracema Andrade; da Cruz, Andrea Cristina Santos; Pereira, Solange Andrade; do Nascimento, Núbia Costa

2011-04-01

Concerns over the sustained availability of fossil fuels and their impact on global warming and pollution have led to the search for fuels from renewable sources to address worldwide rising energy demands. Biodiesel is emerging as one of the possible solutions for the transport sector. It shows comparable engine performance to that of conventional diesel fuel, while reducing greenhouse gas emissions. However, the toxicity of products and effluents from the biodiesel industry has not yet been sufficiently investigated. Brazil has a very high potential as a biodiesel producer, in view of its climatic conditions and vast areas for cropland, with consequent environmental risks because of possible accidental biodiesel spillages into water bodies and runoff to coastal areas. This research determined the toxicity to two marine organisms of the water-soluble fractions (WSF) of three different biodiesel fuels obtained by methanol transesterification of castor oil (CO), palm oil (PO), and waste cooking oil (WCO). Microalgae and sea urchins were used as the test organisms, respectively, for culture-growth-inhibition and early-life-stage-toxicity tests. The toxicity levels of the analyzed biodiesel WSF showed the highest toxicity for the CO, followed by WCO and the PO. Methanol was the most prominent contaminant; concentrations increased over time in WSF samples stored up to 120 d. Copyright © 2010 SETAC.

Evaluation of Castor Oil Cake Starch and Recovered Glycerol and Development of “Green” Composites Based on Those with Plant Fibers

PubMed Central

Guimarães, José Luis; Trindade Cursino, Ana Cristina; Ketzer Saul, Cyro; Sierrakowski, Maria Rita; Ramos, Luiz Pereira; Satyanarayana, Kestur Gundappa

2016-01-01

Continuous efforts are being made in some countries for the recovery of crude glycerin (RG/CG) and castor oil cake (COC), the two byproducts of biodiesel production. These are expected to help, not only in addressing environmental safety, but also in adding value to those byproducts, which otherwise may go to waste. Finding ways to utilize those byproducts underlines the main objective of this study. This paper presents the evaluation of (i) COC, glycerin and banana and sugarcane fibers for moisture content; (ii) COC for structural and thermal properties; and (iii) CG for its chemical characteristics. The possibility of using COC and CG with the selected fibers as reinforcement in the development of bio-composites is attempted through thermo-molding. Results revealed enhanced mechanical properties for these composites. The obtained results are discussed in terms of the observed morphology. PMID:28787878

Inhibitory Effects of Two Varieties of Tunisian Pomegranate (Punica granatum L.) Extracts on Gastrointestinal Transit in Rat.

PubMed

Souli, Abdelaziz; Sebai, Hichem; Rtibi, Kais; Chehimi, Latifa; Sakly, Mohsen; Amri, Mohamed; El-Benna, Jamel; Marzouki, Lamjed

2015-09-01

The present study was undertaken to determine whether total and methanol juice extracts of two Tunisian Pomegranate (Punica granatum L.) varieties (Garsi and Gabsi) protect against diarrhea as well as their effects on gastrointestinal transit (GIT) in healthy rats. In this respect, male Wistar rats were used and divided into control- and pomegranate-treated groups. The antidiarrheal activity was evaluated using the castor oil-induced diarrhea method and the GIT was assessed using charcoal meal. Our results showed that total and methanol P. granatum juice extracts produced a significant dose-dependent protection against castor oil-induced diarrhea. Pomegranate extracts and juice also decreased the GIT significantly and dose dependently. Importantly, the Garsi variety appeared to be more effective than the Gabsi variety on these two parameters. These findings suggest that pomegranate extracts have a potent antidiarrheal property in rats confirming their efficiency in the Tunisian traditional medicine.

Inhibitory Effects of Two Varieties of Tunisian Pomegranate (Punica granatum L.) Extracts on Gastrointestinal Transit in Rat

PubMed Central

Souli, Abdelaziz; Sebai, Hichem; Rtibi, Kais; Chehimi, Latifa; Sakly, Mohsen; Amri, Mohamed; El-Benna, Jamel; Marzouki, Lamjed

2015-01-01

Abstract The present study was undertaken to determine whether total and methanol juice extracts of two Tunisian Pomegranate (Punica granatum L.) varieties (Garsi and Gabsi) protect against diarrhea as well as their effects on gastrointestinal transit (GIT) in healthy rats. In this respect, male Wistar rats were used and divided into control- and pomegranate-treated groups. The antidiarrheal activity was evaluated using the castor oil-induced diarrhea method and the GIT was assessed using charcoal meal. Our results showed that total and methanol P. granatum juice extracts produced a significant dose-dependent protection against castor oil-induced diarrhea. Pomegranate extracts and juice also decreased the GIT significantly and dose dependently. Importantly, the Garsi variety appeared to be more effective than the Gabsi variety on these two parameters. These findings suggest that pomegranate extracts have a potent antidiarrheal property in rats confirming their efficiency in the Tunisian traditional medicine. PMID:25775227

In vitro antimicrobial activity of auxiliary chemical substances and natural extracts on Candida albicans and Enterococcus faecalis in root canals

PubMed Central

VALERA, Marcia Carneiro; MAEKAWA, Lilian Eiko; de OLIVEIRA, Luciane Dias; JORGE, Antonio Olavo Cardoso; SHYGEI, Érika; CARVALHO, Cláudio Antonio Talge

2013-01-01

Objective: The aim of this study was to evaluate the antimicrobial activity of auxiliary chemical substances and natural extracts on Candida albicans and Enterococcus faecalis inoculated in root canals. Material and Methods: Seventy-two human tooth roots were contaminated with C. albicans and E. faecalis for 21 days. The groups were divided according to the auxiliary chemical substance into: G1) 2.5% sodium hypochlorite (NaOCl), G2) 2% chlorhexidine gel (CHX), G3) castor oil, G4) glycolic Aloe vera extract, G5) glycolic ginger extract, and G6) sterile saline (control). The samples of the root canal were collected at different intervals: confirmation collection, at 21 days after contamination; 1st collection, after instrumentation; and 2nd collection, seven days after instrumentation. Microbiological samples were grown in culture medium and incubated at 37º C for 48 hours. Results: The results were submitted to the Kruskal-Wallis and Dunn (5%) statistical tests. NaOCl and CHX completely eliminated the microorganisms of the root canals. Castor oil and ginger significantly reduced the number of CFU of the tested bacteria. Reduction of CFU/mL at the 1st and 2nd collections for groups G1, G2, G3 and G4 was greater in comparison to groups G5 and G6. Conclusion: It was concluded that 2.5% sodium hypochlorite and 2% chlorhexidine gel were more effective in eliminating C. albicans and E. faecalis, followed by the castor oil and glycolic ginger extract. The Aloe vera extract showed no antimicrobial activity. PMID:23739849

In vitro antimicrobial activity of auxiliary chemical substances and natural extracts on Candida albicans and Enterococcus faecalis in root canals.

PubMed

Valera, Marcia Carneiro; Maekawa, Lilian Eiko; de Oliveira, Luciane Dias; Jorge, Antonio Olavo Cardoso; Shygei, Érika; Carvalho, Cláudio Antonio Talge

2013-01-01

The aim of this study was to evaluate the antimicrobial activity of auxiliary chemical substances and natural extracts on Candida albicans and Enterococcus faecalis inoculated in root canals. Seventy-two human tooth roots were contaminated with C. albicans and E. faecalis for 21 days. The groups were divided according to the auxiliary chemical substance into: G1) 2.5% sodium hypochlorite (NaOCl), G2) 2% chlorhexidine gel (CHX), G3) castor oil, G4) glycolic Aloe vera extract, G5) glycolic ginger extract, and G6) sterile saline (control). The samples of the root canal were collected at different intervals: confirmation collection, at 21 days after contamination; 1st collection, after instrumentation; and 2nd collection, seven days after instrumentation. Microbiological samples were grown in culture medium and incubated at 37°C for 48 hours. The results were submitted to the Kruskal-Wallis and Dunn (5%) statistical tests. NaOCl and CHX completely eliminated the microorganisms of the root canals. Castor oil and ginger significantly reduced the number of CFU of the tested bacteria. Reduction of CFU/mL at the 1st and 2nd collections for groups G1, G2, G3 and G4 was greater in comparison to groups G5 and G6. It was concluded that 2.5% sodium hypochlorite and 2% chlorhexidine gel were more effective in eliminating C. albicans and E. faecalis, followed by the castor oil and glycolic ginger extract. The Aloe vera extract showed no antimicrobial activity.

Antidiarrhoeal Activity of Musa paradisiaca Sap in Wistar Rats

PubMed Central

Yakubu, Musa T.; Nurudeen, Quadri O.; Salimon, Saoban S.; Yakubu, Monsurat O.; Jimoh, Rukayat O.; Nafiu, Mikhail O.; Akanji, Musbau A.; Oladiji, Adenike T.; Williams, Felicia E.

2015-01-01

The folkloric claim of Musa paradisiaca sap in the management of diarrhoea is yet to be substantiated or refuted with scientific data. Therefore, the aim of the current study was to screen the sap of M. paradisiaca for both its secondary metabolites and antidiarrhoeal activity at 0.25, 0.50, and 1.00 mL in rats. Secondary metabolites were screened using standard methods while the antidiarrhoeal activity was done by adopting the castor oil-induced diarrhoeal, castor oil-induced enteropooling, and gastrointestinal motility models. The sap contained flavonoids, phenolics, saponins, alkaloids, tannins, and steroids while cardiac glycosides, anthraquinones, triterpenes, cardenolides, and dienolides were not detected. In the castor oil-induced diarrhoeal model, the sap significantly (P < 0.05) prolonged the onset time of diarrhoea, decreased the number, fresh weight, and water content of feaces, and increased the inhibition of defecations. Na+-K+-ATPase activity in the small intestine increased significantly whereas nitric oxide content decreased. The decreases in the masses and volumes of intestinal fluid by the sap were accompanied by increase in inhibition of intestinal fluid content in the enteropooling model. The sap decreased the charcoal meal transit in the gastrointestinal motility model. In all the models, the 1.00 mL of the sap produced changes that compared well with the reference drugs. Overall, the antidiarrhoeal activity of Musa paradisiaca sap attributed to the presence of alkaloids, phenolics, flavonoids, and/or saponins which may involve, among others, enhancing fluid and electrolyte absorption through de novo synthesis of the sodium potassium ATPase and/or reduced nitric oxide levels. PMID:25893000

Antidiarrhoeal Activity of Musa paradisiaca Sap in Wistar Rats.

PubMed

Yakubu, Musa T; Nurudeen, Quadri O; Salimon, Saoban S; Yakubu, Monsurat O; Jimoh, Rukayat O; Nafiu, Mikhail O; Akanji, Musbau A; Oladiji, Adenike T; Williams, Felicia E

2015-01-01

The folkloric claim of Musa paradisiaca sap in the management of diarrhoea is yet to be substantiated or refuted with scientific data. Therefore, the aim of the current study was to screen the sap of M. paradisiaca for both its secondary metabolites and antidiarrhoeal activity at 0.25, 0.50, and 1.00 mL in rats. Secondary metabolites were screened using standard methods while the antidiarrhoeal activity was done by adopting the castor oil-induced diarrhoeal, castor oil-induced enteropooling, and gastrointestinal motility models. The sap contained flavonoids, phenolics, saponins, alkaloids, tannins, and steroids while cardiac glycosides, anthraquinones, triterpenes, cardenolides, and dienolides were not detected. In the castor oil-induced diarrhoeal model, the sap significantly (P < 0.05) prolonged the onset time of diarrhoea, decreased the number, fresh weight, and water content of feaces, and increased the inhibition of defecations. Na(+)-K(+)-ATPase activity in the small intestine increased significantly whereas nitric oxide content decreased. The decreases in the masses and volumes of intestinal fluid by the sap were accompanied by increase in inhibition of intestinal fluid content in the enteropooling model. The sap decreased the charcoal meal transit in the gastrointestinal motility model. In all the models, the 1.00 mL of the sap produced changes that compared well with the reference drugs. Overall, the antidiarrhoeal activity of Musa paradisiaca sap attributed to the presence of alkaloids, phenolics, flavonoids, and/or saponins which may involve, among others, enhancing fluid and electrolyte absorption through de novo synthesis of the sodium potassium ATPase and/or reduced nitric oxide levels.

Identification of critical amino acids in the IgE epitopes of Ric c 1 and Ric c 3 and the application of glutamic acid as an IgE blocker.

PubMed

Deus-de-Oliveira, Natalia; Felix, Shayany P; Carrielo-Gama, Camila; Fernandes, Keysson V; DaMatta, Renato Augusto; Machado, Olga L T

2011-01-01

The allergenicity of Ricinus communis L. (castor bean, Euphorbiaceae) is associated with components of its seeds and pollen. Castor bean allergy has been described not only in laboratory workers, but also in personnel working in oil processing mills, fertilizer retail, the upholstery industry and other industrial fields. In the present study, we describe the critical amino acids in the IgE-binding epitopes in Ric c 1 and Ric c 3, two major allergens of R. communis. In addition, we also investigate the cross-reactivity between castor bean and some air and food allergen extracts commonly used in allergy diagnosis. The IgE reactivity of human sera from atopic patients was screened by immune-dot blot against castor bean allergens. Allergenic activity was evaluated in vitro using a rat mast cell activation assay and by ELISA. Cross-reactivity was observed between castor bean allergens and extracts from shrimp, fish, gluten, wheat, soybean, peanut, corn, house dust, tobacco and airborne fungal allergens. We observed that treatment of rat and human sera (from atopic patients) with glutamic acid reduced the IgE-epitope interaction. The identification of glutamic acid residues with critical roles in IgE-binding to Ric c 3 and Ric c 1 support the potential use of free amino acids in allergy treatment.

21 CFR 524.2620 - Liquid crystalline trypsin, Peru balsam, castor oil.

Code of Federal Regulations, 2014 CFR

2014-04-01

... paragraph (a)(2). (c) Conditions of use—(1) Amount. Apply directly to the wound site. (2) Indications for use. As an aid in the treatment of external wounds and assists healing by facilitating the removal of...

Influence of Temperature on Pyrolysis of Biomass

NASA Astrophysics Data System (ADS)

Kumar, S.; Pattnaik, D.; Bhuyan, S. K.; Mishra, S. C.

2018-03-01

The Antimicrobial and anti-inflammatory nature of the castor oil is used for the treatment of constipation and also used to clean the intestine before a surgical treatment. The growing demand castor oil due to its cheaper price and have much demand to grow hairs faster which give proteins to hair and increases the life span of hair and increases the hair capacity and provide hair smoothness because it has high ricinoleic ratio which is beneficial for skin and hair. The main objective of this paper is by observing its usefulness and the current aim for the research work is to produce bio-char/carbon compounds and extraction of higher carbon content. The castor leaves are collected and dried in the sun light to get it moisture free and proximate analysis is studied that reveals 14% of fixed amount of carbon. The dried leaves of castor plant are pyrolized at different temperature ranges 250°C, 350 °C, 450°C, 600°C and 900°C. The pyrolised specimens were studied by Fourier-transform infrared spectroscopy analysis which shows the transformation and formation of several bonds including carbon bonds which are affected during carbonization. Scanning electron microscope and energy dispersive x-ray spectroscopy have been studied on pyrolised specimen to get microstructures elements in the bio-char. The parameter called carbon/oxygen ration gives the advantage of char in the agricultural land for fertility motive and discrepancy of carbon and oxygen contents have been analysed. It has been found that carbon/oxygen ration increased along increment in Pyrolysis tempt. Up to 500°C and therefore along moreover increment in tempt. Beyond 500°C there is a decrement trend has been found.

Optimization of Ultrasonic-Microwave Synergistic Extraction of Ricinine from Castor Cake by Response Surface Methodology.

PubMed

Xu, Wei; Yan, Xiuhua; Shao, Rong; Chen, Ligen; Ke, Zengguang

Castor cake is the residue in castor oil production in which many active components exist and the major one among them is ricinine. In this study, optimization of extraction of ricinine from castor cake using ultrasonic-microwave synergistic extraction (UMSE) was investigated to obtain high yield and purity by Box-Behnken design (BBD) response surface design. The optimal conditions of extraction were: ultrasound power 342 W, extracting time 5 min, microwave power 395 W, and non-significant factor of liquid/solid ratio 1:10. The crude extraction was recrystallized from ethanol. As a result, the maximum yield of ricinine was approximately 67.52%. The purity of ricinine was 99.39% which was determined by high performance liquid chromatography (HPLC). Additionally, the structure of purified ricinine was identified by fourier transforms infrared (FTIR) and liquid chromatography-mass spectrometry (LC-MS). Scanning electron microscope (SEM) was used to characterize the prismatic crystals morphology of ricinine. Results demonstrated that the present method combined the advantages of ultrasonic extraction and microwave extraction, which is time-saving with high extraction yield. Our results offer a suitable method for large-scale isolation of ricinine.

Thermal properties measurements in biodiesel oils using photothermal techniques

NASA Astrophysics Data System (ADS)

Castro, M. P. P.; Andrade, A. A.; Franco, R. W. A.; Miranda, P. C. M. L.; Sthel, M.; Vargas, H.; Constantino, R.; Baesso, M. L.

2005-08-01

In this Letter, thermal lens and open cell photoacoustic techniques are used to measure the thermal properties of biodiesel oils. The absolute values of the thermal effusivity, thermal diffusivity, thermal conductivity and the temperature coefficient of the refractive index were determined for samples obtained from soy, castor bean, sunflower and turnip. The results suggest that the employed techniques may be useful as complementary methods for biodiesel certification.

Development, Characterization, and In Vitro Biological Performance of Fluconazole-Loaded Microemulsions for the Topical Treatment of Cutaneous Leishmaniasis

PubMed Central

Graminha, Márcia; Cerecetto, Hugo; González, Mercedes

2015-01-01

Cutaneous leishmaniasis (CL) is a resistant form of leishmaniasis that is caused by a parasite belonging to the genus Leishmania. FLU-loaded microemulsions (MEs) were developed by phase diagram for topical administration of fluconazole (FLU) as prominent alternative to combat CL. Three MEs called F1, F2, and F3 (F1—60% 50 M phosphate buffer at pH 7.4 (PB) as aqueous phase, 10% cholesterol (CHO) as oil phase, and 30% soy phosphatidylcholine/oil polyoxyl-60 hydrogenated castor oil/sodium oleate (3/8/6) (S) as surfactant; F2—50% PB, 10% CHO, and 40% S; F3—40% PB, 10% CHO, and 50 % S) were characterized by droplet size analysis, zeta potential analysis, X-ray diffraction, continuous flow, texture profile analysis, and in vitro bioadhesion. MEs presented pseudoplastic flow and thixotropy was dependent on surfactant concentration. Droplet size was not affected by FLU. FLU-loaded MEs improved the FLU safety profile that was evaluated using red cell haemolysis and in vitro cytotoxicity assays with J-774 mouse macrophages. FLU-unloaded MEs did not exhibit leishmanicidal activity that was performed using MTT colourimetric assays; however, FLU-loaded MEs exhibited activity. Therefore, these MEs have potential to modulate FLU action, being a promising platform for drug delivery systems to treat CL. PMID:25650054

Microwave Propagation in Dielectric Fluids.

ERIC Educational Resources Information Center

Lonc, W. P.

1980-01-01

Describes an undergraduate experiment designed to verify quantitatively the effect of a dielectric fluid's dielectric constant on the observed wavelength of microwave radiation propagating through the fluid. The fluid used is castor oil, and results agree with the expected behavior within 5 percent. (Author/CS)

Molecular simulation of fibronectin adsorption onto polyurethane surfaces

USDA-ARS?s Scientific Manuscript database

Polyethylene glycol-based polyurethanes have been widely used in biomedical applications, however are prone to swelling. A natural polyol, castor oil can be incorporated into these polyurethanes to control the degree of the swelling, which alters mechanical properties and protein adsorption characte...

Genotyping and Bioforensics of Ricinus communis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hinckley, Aubree Christine

The castor bean plant (Ricinus communis) is a member of the family Euphorbiaceae. In spite of its common name, the castor plant is not a true bean (i.e., leguminous plants belonging to the family, Fabaceae). Ricinus communis is native to tropical Africa, but because the plant was recognized for its production of oil with many desirable properties, it has been introduced and cultivated in warm temperate regions throughout the world (Armstrong 1999 and Brown 2005). Castor bean plants have also been valued by gardeners as an ornamental plant and, historically, as a natural rodenticide. Today, escaped plants grow like weedsmore » throughout much of the southwestern United States, and castor seeds are even widely available to the public for order through the Internet. In this study, multiple loci of chloroplast noncoding sequence data and a few nuclear noncoding regions were examined to identify DNA polymorphisms present among representatives from a geographically diverse panel of Ricinus communis cultivated varieties. The primary objectives for this research were (1) to successfully cultivate castor plants and extract sufficient yields of high quality DNA from an assortment of castor cultivated varieties, (2) to use PCR and sequencing to screen available universal oligos against a small panel of castor cultivars, (3) to identify DNA polymorphisms within the amplified regions, and (4) to evaluate these DNA polymorphisms as appropriate candidates for assay development (see Figure 1). Additional goals were to design, test and optimize assays targeting any DNA polymorphisms that were discovered and to rapidly screen many castor cultivars to determine the amount of diversity present at that particular locus. Ultimately, the goal of this study was to construct a phylogeographic tree representing the genetic relationships present among Ricinus communis cultivars from diverse geographic regions. These research objectives were designed to test the hypothesis that cultivated varieties of Ricinus communis from various geographic regions can be distinguished from one another based on differences present at the genetic level. In addition, the present study sought to determine the amount of diversity present among Ricinus communis cultivars.« less

Reducing Isozyme Competition Increases Target Fatty Acid Accumulation in Seed Triacylglycerols of Transgenic Arabidopsis1[OPEN

PubMed Central

van Erp, Harrie; Shockey, Jay; Zhang, Meng; Adhikari, Neil D.; Browse, John

2015-01-01

One goal of green chemistry is the production of industrially useful fatty acids (FAs) in crop plants. We focus on hydroxy fatty acids (HFAs) and conjugated polyenoic FAs (α-eleostearic acids [ESAs]) using Arabidopsis (Arabidopsis thaliana) as a model. These FAs are found naturally in seed oils of castor (Ricinus communis) and tung tree (Vernicia fordii), respectively, and used for the production of lubricants, nylon, and paints. Transgenic oils typically contain less target FA than that produced in the source species. We hypothesized that competition between endogenous and transgenic isozymes for substrates limits accumulation of unique FAs in Arabidopsis seeds. This hypothesis was tested by introducing a mutation in Arabidopsis diacylglycerol acyltransferase1 (AtDGAT1) in a line expressing castor FA hydroxylase and acyl-Coenzyme A:RcDGAT2 in its seeds. This led to a 17% increase in the proportion of HFA in seed oil. Expression of castor phospholipid:diacylglycerol acyltransferase 1A in this line increased the proportion of HFA by an additional 12%. To determine if our observations are more widely applicable, we investigated if isozyme competition influenced production of ESA. Expression of tung tree FA conjugase/desaturase in Arabidopsis produced approximately 7.5% ESA in seed lipids. Coexpression of VfDGAT2 increased ESA levels to approximately 11%. Overexpression of VfDGAT2 combined with suppression of AtDGAT1 increased ESA accumulation to 14% to 15%. Our results indicate that isozyme competition is a limiting factor in the engineering of unusual FAs in heterologous plant systems and that reduction of competition through mutation and RNA suppression may be a useful component of seed metabolic engineering strategies. PMID:25739701

Comparison of polyurethane with cyanoacrylate in hemostasis of vascular injury in guinea pigs.

PubMed

Kubrusly, Luiz Fernando; Formighieri, Marina Simões; Lago, José Vitor Martins; Graça, Yorgos Luiz Santos de Salles; Sobral, Ana Cristina Lira; Lago, Marianna Martins

2015-01-01

To evaluate the behavior of castor oil-derived polyurethane as a hemostatic agent and tissue response after abdominal aortic injury and to compare it with 2-octyl-cyanoacrylate. Twenty-four Guinea Pigs were randomly divided into three groups of eight animals (I, II, and III). The infrarenal abdominal aorta was dissected, clamped proximally and distally to the vascular puncture site. In group I (control), hemostasis was achieved with digital pressure; in group II (polyurethane) castor oil-derived polyurethane was applied, and in group III (cyanoacrylate), 2-octyl-cyanoacrylate was used. Group II was subdivided into IIA and IIB according to the time of preparation of the hemostatic agent. Mean blood loss in groups IIA, IIB and III was 0.002 grams (g), 0.008 g, and 0.170 g, with standard deviation of 0.005 g, 0.005 g, and 0.424 g, respectively (P=0.069). The drying time for cyanoacrylate averaged 81.5 seconds (s) (standard deviation: 51.5 seconds) and 126.1 s (standard deviation: 23.0 s) for polyurethane B (P=0.046). However, there was a trend (P=0.069) for cyanoacrylate to dry more slowly than polyurethane A (mean: 40.5 s; SD: 8.6 s). Furthermore, polyurethane A had a shorter drying time than polyurethane B (P=0.003), mean IIA of 40.5 s (standard deviation: 8.6 s). In group III, 100% of the animals had mild/severe fibrosis, while in group II only 12.5% showed this degree of fibrosis (P=0.001). Polyurethane derived from castor oil showed similar hemostatic behavior to octyl-2-cyanoacrylate. There was less perivascular tissue response with polyurethane when compared with cyanoacrylate.

Antidiarrheal activity of methanolic extract of the root bark of Cordia africana

PubMed Central

Asrie, Assefa Belay; Abdelwuhab, Mohammedbrhan; Shewamene, Zewdneh; Gelayee, Desalegn Asmelashe; Adinew, Getnet Mequanint; Birru, Eshetie Melese

2016-01-01

An ethnobotanical study in Agew-Awi and Amhara peoples in northwest Ethiopia reported that Cordia africana is used traditionally in the treatment of liver disease, amebiasis, stomachache, and diarrhea. The root and root bark are reported to be used in the treatment of diarrhea. Therefore, this study was intended to evaluate the antidiarrheal effect of C. africana against castor oil-induced diarrhea in mice. The antidiarrheal effect of the plant was tested on castor oil-induced diarrhea in mice (23–25 g) of either sex. Number of diarrheic defecations, intestinal length traveled by the charcoal meal, and weight of intestinal fluid were taken as important parameters to evaluate the antidiarrheal activity of the plant extract. In preliminary phytochemical screening tests, the methanolic extract of C. africana was found to contain phenols, flavonoids, terpenoids, and saponins. Reduction in the number of diarrheic drops was observed in groups of mice that received 200 mg/kg (P<0.05) and 400 mg/kg (P<0.01) of the extract compared to the negative controls. The percent inhibition of intestinal fluid accumulation was 26.83%, 46.34%, and 53.66% at the doses of 100, 200, and 400 mg/kg of the extract, respectively. Relative to the negative control group, the mean percent of intestinal length moved by the charcoal meal was decreased by 24.41%, 39.89%, and 51.66% in groups of mice given 100, 200, and 400 mg/kg of the plant extract, respectively. To iterate the finding, the root bark extract of C. africana was found to be effective in preventing castor oil-induced diarrhea and intestinal motility in a dose-dependent manner. This reveals that the plant material has promising antidiarrheal activity as it is claimed in traditional medical practice. PMID:27799833

Antidiarrheal activity of methanolic extract of the root bark of Cordia africana.

PubMed

Asrie, Assefa Belay; Abdelwuhab, Mohammedbrhan; Shewamene, Zewdneh; Gelayee, Desalegn Asmelashe; Adinew, Getnet Mequanint; Birru, Eshetie Melese

2016-01-01

An ethnobotanical study in Agew-Awi and Amhara peoples in northwest Ethiopia reported that Cordia africana is used traditionally in the treatment of liver disease, amebiasis, stomachache, and diarrhea. The root and root bark are reported to be used in the treatment of diarrhea. Therefore, this study was intended to evaluate the antidiarrheal effect of C. africana against castor oil-induced diarrhea in mice. The antidiarrheal effect of the plant was tested on castor oil-induced diarrhea in mice (23-25 g) of either sex. Number of diarrheic defecations, intestinal length traveled by the charcoal meal, and weight of intestinal fluid were taken as important parameters to evaluate the antidiarrheal activity of the plant extract. In preliminary phytochemical screening tests, the methanolic extract of C. africana was found to contain phenols, flavonoids, terpenoids, and saponins. Reduction in the number of diarrheic drops was observed in groups of mice that received 200 mg/kg ( P <0.05) and 400 mg/kg ( P <0.01) of the extract compared to the negative controls. The percent inhibition of intestinal fluid accumulation was 26.83%, 46.34%, and 53.66% at the doses of 100, 200, and 400 mg/kg of the extract, respectively. Relative to the negative control group, the mean percent of intestinal length moved by the charcoal meal was decreased by 24.41%, 39.89%, and 51.66% in groups of mice given 100, 200, and 400 mg/kg of the plant extract, respectively. To iterate the finding, the root bark extract of C. africana was found to be effective in preventing castor oil-induced diarrhea and intestinal motility in a dose-dependent manner. This reveals that the plant material has promising antidiarrheal activity as it is claimed in traditional medical practice.

Comparison of polyurethane with cyanoacrylate in hemostasis of vascular injury in guinea pigs

PubMed Central

Kubrusly, Luiz Fernando; Formighieri, Marina Simões; Lago, José Vitor Martins; Graça, Yorgos Luiz Santos de Salles; Sobral, Ana Cristina Lira; Lago, Marianna Martins

2015-01-01

Objective To evaluate the behavior of castor oil-derived polyurethane as a hemostatic agent and tissue response after abdominal aortic injury and to compare it with 2-octyl-cyanoacrylate. Methods Twenty-four Guinea Pigs were randomly divided into three groups of eight animals (I, II, and III). The infrarenal abdominal aorta was dissected, clamped proximally and distally to the vascular puncture site. In group I (control), hemostasis was achieved with digital pressure; in group II (polyurethane) castor oil-derived polyurethane was applied, and in group III (cyanoacrylate), 2-octyl-cyanoacrylate was used. Group II was subdivided into IIA and IIB according to the time of preparation of the hemostatic agent. Results Mean blood loss in groups IIA, IIB and III was 0.002 grams (g), 0.008 g, and 0.170 g, with standard deviation of 0.005 g, 0.005 g, and 0.424 g, respectively (P=0.069). The drying time for cyanoacrylate averaged 81.5 seconds (s) (standard deviation: 51.5 seconds) and 126.1 s (standard deviation: 23.0 s) for polyurethane B (P=0.046). However, there was a trend (P=0.069) for cyanoacrylate to dry more slowly than polyurethane A (mean: 40.5 s; SD: 8.6 s). Furthermore, polyurethane A had a shorter drying time than polyurethane B (P=0.003), mean IIA of 40.5 s (standard deviation: 8.6 s). In group III, 100% of the animals had mild/severe fibrosis, while in group II only 12.5% showed this degree of fibrosis (P=0.001). Conclusion Polyurethane derived from castor oil showed similar hemostatic behavior to octyl-2-cyanoacrylate. There was less perivascular tissue response with polyurethane when compared with cyanoacrylate. PMID:25859876

Identification of Critical Amino Acids in the IgE Epitopes of Ric c 1 and Ric c 3 and the Application of Glutamic Acid as an IgE Blocker

PubMed Central

Deus-de-Oliveira, Natalia; Felix, Shayany P.; Carrielo-Gama, Camila; Fernandes, Keysson V.; DaMatta, Renato Augusto; Machado, Olga L. T.

2011-01-01

Background The allergenicity of Ricinus communis L. (castor bean, Euphorbiaceae) is associated with components of its seeds and pollen. Castor bean allergy has been described not only in laboratory workers, but also in personnel working in oil processing mills, fertilizer retail, the upholstery industry and other industrial fields. In the present study, we describe the critical amino acids in the IgE-binding epitopes in Ric c 1 and Ric c 3, two major allergens of R. communis. In addition, we also investigate the cross-reactivity between castor bean and some air and food allergen extracts commonly used in allergy diagnosis. Methodology/Principal Findings The IgE reactivity of human sera from atopic patients was screened by immune-dot blot against castor bean allergens. Allergenic activity was evaluated in vitro using a rat mast cell activation assay and by ELISA. Cross-reactivity was observed between castor bean allergens and extracts from shrimp, fish, gluten, wheat, soybean, peanut, corn, house dust, tobacco and airborne fungal allergens. We observed that treatment of rat and human sera (from atopic patients) with glutamic acid reduced the IgE-epitope interaction. Conclusions/Significance The identification of glutamic acid residues with critical roles in IgE-binding to Ric c 3 and Ric c 1 support the potential use of free amino acids in allergy treatment. PMID:21738671

Preparation and Characterization of All-Biomass Soy Protein Isolate-Based Films Enhanced by Epoxy Castor Oil Acid Sodium and Hydroxypropyl Cellulose

PubMed Central

Wang, La; Li, Jianzhang; Zhang, Shifeng; Shi, Junyou

2016-01-01

All-biomass soy protein-based films were prepared using soy protein isolate (SPI), glycerol, hydroxypropyl cellulose (HPC) and epoxy castor oil acid sodium (ECOS). The effect of the incorporated HPC and ECOS on the properties of the SPI film was investigated. The experimental results showed that the tensile strength of the resultant films increased from 2.84 MPa (control) to 4.04 MPa and the elongation at break increased by 22.7% when the SPI was modified with 2% HPC and 10% ECOS. The increased tensile strength resulted from the reaction between the ECOS and SPI, which was confirmed by attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), scanning electron microscopy (SEM) and X-ray diffraction analysis (XRD). It was found that ECOS and HPC effectively improved the performance of SPI-based films, which can provide a new method for preparing environmentally-friendly polymer films for a number of commercial applications. PMID:28773320

Preparation and Characterization of All-Biomass Soy Protein Isolate-Based Films Enhanced by Epoxy Castor Oil Acid Sodium and Hydroxypropyl Cellulose.

PubMed

Wang, La; Li, Jianzhang; Zhang, Shifeng; Shi, Junyou

2016-03-15

All-biomass soy protein-based films were prepared using soy protein isolate (SPI), glycerol, hydroxypropyl cellulose (HPC) and epoxy castor oil acid sodium (ECOS). The effect of the incorporated HPC and ECOS on the properties of the SPI film was investigated. The experimental results showed that the tensile strength of the resultant films increased from 2.84 MPa (control) to 4.04 MPa and the elongation at break increased by 22.7% when the SPI was modified with 2% HPC and 10% ECOS. The increased tensile strength resulted from the reaction between the ECOS and SPI, which was confirmed by attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), scanning electron microscopy (SEM) and X-ray diffraction analysis (XRD). It was found that ECOS and HPC effectively improved the performance of SPI-based films, which can provide a new method for preparing environmentally-friendly polymer films for a number of commercial applications.

Studies on performance evaluation of a green plasticizer made by enzymatic esterification of furfuryl alcohol and castor oil fatty acid.

PubMed

Mukherjee, Sohini; Ghosh, Mahua

2017-02-10

The esterification of furfuryl alcohol (FA) and castor oil fatty acid (COFA) at 3:1 molar ratio, by immobilized Candida antarctica Lipase B (NS 435 from Novozyme) in a solvent free system gave a maximum yield of 88.64% (%w/w) at 5h. Performance of the FA-COFA ester plasticized Ethyl Cellulose (EC) films were evaluated by surface morphologies, XRD analysis, mechanical properties,thermal properties, water vapor permeability and migration stability test. It was an effective plasticizer with better mechanical properties and thermal stability at the increasing concentration of FA-COFA ester (15-25%) containing EC film, than the traditional plasticizer, i.e; dibutyl phthalate (DBP) in producing good quality films. Chemical structure and the intermolecular interactions between FA-COFA ester and ethyl cellulose chains were the causative agents of these outstanding performances. Therefore, this FA-COFA ester, with significant plasticizing property, at a certain concentration, can be a substitute of DBP. Copyright © 2016 Elsevier Ltd. All rights reserved.

Bio-inspired hydrophobic modification of cellulose nanocrystals with castor oil.

PubMed

Shang, Qianqian; Liu, Chengguo; Hu, Yun; Jia, Puyou; Hu, Lihong; Zhou, Yonghong

2018-07-01

This work presents an efficient and environmentally friendly approach to generate hydrophobic cellulose nanocrystals (CNC) using thiol-containing castor oil (CO-SH) as a renewable hydrophobe with the assist of bio-inspired dopamine at room temperature. The modification process included the formation of the polydopamine (PDA) buffer layer on CNC surfaces and the Michael addition reaction between the catechol moieties of PDA coating and thiol groups of CO-SH. The morphology, crystalline structure, surface chemistry, thermal stability and hydrophobicity of the modified CNC were charactered by TEM, XRD, FT-IR, solid-state 13 C NMR, XPS, TGA and contact angle analysis. The modified CNC preserved cellulose crystallinity, displayed higher thermal stability than unmodified CNC, and was highly hydrophobic with a water contact angle of 95.6°. The simplicity and versatility of the surface modification strategy inspired by adhesive protein of mussel may promote rapid development of hydrophobic bio-based nanomaterials for various applications. Copyright © 2018 Elsevier Ltd. All rights reserved.

Immune system stimulation in rats by Lactobacillus sp. isolates from Raffia wine (Raphia vinifera).

PubMed

Flore, Tiepma N E; François, Zambou N; Félicité, Tchouanguep M

2010-01-01

The immune system consists of organs and several cell types. Antigen interaction with these cells induces a cellular immune response mediated by activated cells. The effects of lactic acid bacteria on the systemic immune response and on the secretory immune system are described. The current investigation sets out to examine the possible effects of isolated wine lacto-bacilli upon various hematologic and immunologic parameters in rats. We have fed rats with probiotic isolates from Raffia wine and challenged with castor oil; two control groups were fed with castor oil and others were not. We counted blood cells at the end of the experiment; all isolates seemed to cause a decrease of circulating white blood cells. The percentage of lymphocytes and the total protein in the spleen increased in the treated animals; also a normal aspect of faeces was observed compared to the control. These isolates of Lactobacillus seem to occur to immune cell-mediated responses in rats.

Enhancement of Oral Bioavailability of Curcumin by a Novel Solid Dispersion System.

PubMed

Hu, Liandong; Shi, Yanjing; Li, Jian Heng; Gao, Na; Ji, Jing; Niu, Feng; Chen, Queting; Yang, Xiaoning; Wang, Shaocheng

2015-12-01

The objective of this study was to improve the solubility and bioavailability of curcumin by a new curcumin dripping pills (Cur-DPs) formulation using melt mixing methods. The optimal formulation consisted of Polyethoxylated 40 hydrogenated castor oil (Cremophor RH40), Poloxamer 188, and Polyethylene glycol 4000 (PEG 4000). Differential scanning calorimetry (DSC), powder X-ray diffraction (PXRD), and Fourier-transform infrared spectroscopy (FT-IR) were used to verify the forming of Cur-DPs. All the physical characterization information proved the formation of Cur-DPs, and the results demonstrated the superiority of the dripping pills in dissolution rates. The pharmacokinetic study of Cur-DPs was performed in rats compared to the pure curcumin suspension. The oral bioavailability of poorly water-soluble curcumin was successfully improved by CUR-DPs. And the stability of prepared Cur-DP was also in a good state in 3 months. These results identified the Cur-DPs was an effective new approach for pharmaceutical application.

Acetone Powder From Dormant Seeds of Ricinus communis L

NASA Astrophysics Data System (ADS)

Cavalcanti, Elisa D. C.; Maciel, Fábio M.; Villeneuve, Pierre; Lago, Regina C. A.; Machado, Olga L. T.; Freire, Denise M. G.

The influence of several factors on the hydrolytic activity of lipase, present in the acetone powder from dormant castor seeds (Ricinus communis) was evaluated. The enzyme showed a marked specificity for short-chain substrates. The best reaction conditions were an acid medium, Triton X-100 as the emulsifying agent and a temperature of 30°C. The lipase activity of the acetone powder of different castor oil genotypes showed great variability and storage stability of up to 90%. The toxicology analysis of the acetone powder from genotype Nordestina BRS 149 showed a higher ricin (toxic component) content, a lower 2S albumin (allergenic compound) content, and similar allergenic potential compared with untreated seeds.

Natural oils and waxes: studies on stick bases.

PubMed

Budai, Lívia; Antal, István; Klebovich, Imre; Budai, Marianna

2012-01-01

The objective of the present article was to examine the role of origin and quantity of selected natural oils and waxes in the determination of the thermal properties and hardness of stick bases. The natural oils and waxes selected for the study were sunflower, castor, jojoba, and coconut oils. The selected waxes were yellow beeswax, candelilla wax, and carnauba wax. The hardness of the formulations is a critical parameter from the aspect of their application. Hardness was characterized by the measurement of compression strength along with the softening point, the drop point, and differential scanning calorimetry (DSC). It can be concluded that coconut oil, jojoba oil, and carnauba wax have the greatest influence on the thermal parameters of stick bases.

Ratios of regioisomers of minor acylglycerols less polar than triricinolein in castor oil estimated by mass spectrometry

USDA-ARS?s Scientific Manuscript database

We have recently reported the identification of forty new minor molecular species of acylglycerols containing hydroxy fatty acids less polar than triricinolein by electrospray ionization mass spectrometry of the lithium adducts. The ratios of regioisomers of triacylglycerols (ABC and AAB types) and ...

A Simple Boyle's Law Experiment.

ERIC Educational Resources Information Center

Lewis, Don L.

1997-01-01

Describes an experiment to demonstrate Boyle's law that provides pressure measurements in a familiar unit (psi) and makes no assumptions concerning atmospheric pressure. Items needed include bathroom scales and a 60-ml syringe, castor oil, disposable 3-ml syringe and needle, modeling clay, pliers, and a wooden block. Commercial devices use a…

Microemulsion formulation of clonixic acid: solubility enhancement and pain reduction.

PubMed

Lee, Jung-Mi; Park, Kyung-Mi; Lim, Soo-Jeong; Lee, Mi-Kyung; Kim, Chong-Kook

2002-01-01

Clonixic acid is currently marketed as a salt form because of its poor water-solubility. However, the commercial dosage form causes severe pain after intramuscular or intravenous injection. To improve the solubility of clonixic acid and to reduce pain on injection, clonixic acid was incorporated into oil-in-water microemulsions prepared from pre-microemulsion concentrate composed of varying ratios of oil and surfactant mixture. As an oil phase for drug incorporation, up to 14% castor oil could be included in the pre-microemulsion concentrate without a significant increase in droplet size. Both drug contents and droplet size increased as the weight ratio of Tween 20 to Tween 85 decreased. Taken together, when microemulsions were prepared from pre-microemulsion concentrate composed of 5:12:18 weight ratio of castor oil:Tween 20:Tween 85, clonixic acid could be incorporated at 3.2 mg mL(-1) in the microemulsion with a droplet size of less than 120 nm. The osmotic pressure of this microemulsion was remarkably lower than the commercial formulation, irrespective of the dilution ratios. The rat paw-lick test was used to compare pain responses among formulations. The microemulsion formulation significantly reduced the number of rats licking their paws as well as the total licking time, suggesting less pain induction by the microemulsion formulation. The pharmacokinetic parameters of clonixic acid after intravenous administration of the clonixic acid microemulsion to rats were not significantly different from those of the commercial formulation, lysine clonixinate. The present study suggests that microemulsion is an alternative formulation for clonixic acid with improved characteristics.

Pyruvate metabolism in castor-bean mitochondria.

PubMed Central

Brailsford, M A; Thompson, A G; Kaderbhai, N; Beechey, R B

1986-01-01

We report the isolation of mitochondria from the endosperm of castor beans (Ricinus communis). These mitochondria oxidized succinate, external NADH, malate and pyruvate with respiratory-control and ADP/O ratios consistent with those found previously with mitochondria from other plant sources. The mitochondria exhibited considerable sensitivity to the electron-transport-chain inhibitors antimycin A and cyanide when oxidizing succinate and external NADH. Pyruvate-dependent O2 uptake was relatively insensitive to these inhibitors, although the residual O2 uptake could be inhibited by salicylhydroxamic acid. We conclude that a cyanide-insensitive alternative terminal oxidase is functional in these mitochondria. However, electrons from the succinate dehydrogenase or external NADH dehydrogenase seem to have no access to this pathway. There is little interconnection between the salicylhydroxamic acid-sensitive and cyanide-sensitive pathways of electron transport. alpha-Cyanocinnamate and its analogues, compound UK5099 [alpha-cyano-beta-(1-phenylindol-3-yl)acrylate] and alpha-cyano-4-hydroxycinnamate, were all found to be potent non-competitive inhibitors of pyruvate oxidation in castor-bean mitochondria. The accumulation of pyruvate by castor-bean mitochondria was determined by using a silicone-oil-centrifugation technique. The accumulation was shown to observe Michaelis-Menten kinetics, with a Km for pyruvate of 0.10 mM and a Vmax. of 0.95 nmol/min per mg of mitochondrial protein. However, the observed rates of pyruvate accumulation were insufficient to account for the pyruvate oxidation rates found in the oxygen-electrode studies. We were able to demonstrate that this is due to the immediate export of the accumulated radiolabel in the form of malate and citrate. Compound UK5099 inhibited the accumulation of [2-14C]pyruvate by castor-bean mitochondria at concentrations similar to those required to inhibit pyruvate oxidation. PMID:3814077

GOLD PLATING PROCESS

DOEpatents

Seegmiller, R.

1957-08-01

An improved bath is reported for plating gold on other metals. The composition of the plating bath is as follows: Gold cyanide from about 15 to about 50 grams, potassium cyanide from about 70 to about 125 grams, and sulfonated castor oil from about 0.1 to about 10 cc. The gold plate produced from this bath is smooth, semi-hard, and nonporous.

Forensic assays of ricin: development of snp assays to generate precise genetic signatures for mixed genotypes found in ricin preparations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jackson, Paul J.; Hill, Karen K.

2009-11-09

The results outlined in this report provide the information for needed to apply a SNP-based forensic analysis to diverse ricin preparations. The same methods could be useful in castor breeding programs that seek to reduce or eliminate ricin in oil-producing R. communis cultivars.

21 CFR 524.2620 - Liquid crystalline trypsin, Peru balsam, castor oil.

Code of Federal Regulations, 2013 CFR

2013-04-01

...) Conditions of use. The drug is used as an aid in the treatment of external wounds and assists healing by... delivered to the wound site contains 0.12 milligram of crystalline trypsin, 87.0 milligrams of Peru balsam... gram delivered to the wound site contains 0.1 milligram of crystalline trypsin, 72.5 milligrams of Peru...

21 CFR 524.2620 - Liquid crystalline trypsin, Peru balsam, castor oil.

Code of Federal Regulations, 2012 CFR

2012-04-01

...) Conditions of use. The drug is used as an aid in the treatment of external wounds and assists healing by... delivered to the wound site contains 0.12 milligram of crystalline trypsin, 87.0 milligrams of Peru balsam... gram delivered to the wound site contains 0.1 milligram of crystalline trypsin, 72.5 milligrams of Peru...

21 CFR 524.2620 - Liquid crystalline trypsin, Peru balsam, castor oil.

Code of Federal Regulations, 2011 CFR

2011-04-01

... delivered to the wound site contains 0.12 milligram of crystalline trypsin, 87.0 milligrams of Peru balsam... gram delivered to the wound site contains 0.1 milligram of crystalline trypsin, 72.5 milligrams of Peru...) Conditions of use. The drug is used as an aid in the treatment of external wounds and assists healing by...

21 CFR 524.2620 - Liquid crystalline trypsin, Peru balsam, castor oil.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) Conditions of use. The drug is used as an aid in the treatment of external wounds and assists healing by... delivered to the wound site contains 0.12 milligram of crystalline trypsin, 87.0 milligrams of Peru balsam... gram delivered to the wound site contains 0.1 milligram of crystalline trypsin, 72.5 milligrams of Peru...

Integration of Gas Chromatography Mass Spectrometry Methods for Differentiating Ricin Preparation Methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wunschel, David S.; Melville, Angela M.; Ehrhardt, Christopher J.

2012-05-17

The investigation of crimes involving chemical or biological agents is infrequent, but presents unique analytical challenges. The protein toxin ricin is encountered more frequently than other agents and is found in the seeds of the castor plant Ricinus communis. Typically, the toxin is extracted from castor seeds utilizing a variety of different recipes that result in varying purity of the toxin. Moreover, these various purification steps can also leave or differentially remove a variety of exogenous and endogenous residual components with the toxin that may indicate the type and number of purification steps involved. We have applied three gas chromatographicmore » - mass spectrometric (GC-MS) based analytical methods to measure the variation in seed carbohydrates and castor oil ricinoleic acid as well as the presence of solvents used for purification. These methods were applied to the same samples prepared using four previously identified toxin preparation methods starting from four varieties of castor seeds. The individual data sets for seed carbohydrate profiles, ricinoleic acid or acetone amount each provided information capable of differentiating different types of toxin preparations across seed types. However, the integration of the data sets using multivariate factor analysis provided a clear distinction of all samples based on the preparation method and independent of the seed source. In particular the abundance of mannose, arabinose, fucose, ricinoleic acid and acetone were shown to be important differentiating factors. These complementary tools provide a more confident determination of the method of toxin preparation.« less

Comparison of pressure ulcer treatments in long-term care facilities: clinical outcomes and impact on cost.

PubMed

Narayanan, Siva; Van Vleet, John; Strunk, Billy; Ross, Robert N; Gray, Mikel

2005-01-01

This study compared clinical outcomes and nursing labor costs associated with (a) balsam Peru, hydrogenated castor oil, and trypsin (BCT) ointment; (b) BCT + Other; and (c) Other treatments in 2014 wound episodes occurring in 861 patients (mean 2.34 wounds/patient). Treatment with BCT ointment or BCT + Other was associated with a higher healing rate (P < .05). No Stage 1 or 2 ulcer treated with BCT ointment progressed, compared with 13.8% treated with BCT + Other and 13.4% treated with Other. The reported mean duration of treatment and time to heal were shorter for ulcers treated with BCT ointment, but differences did not reach significance, possibly because of the variability in reported treatment times. Mean daily nursing labor costs were lower for treatment with BCT than Other ($50.8 vs $61.7, P < .05). These data suggest that treatment of Stage 1 or 2 ulcers with BCT may be associated with shorter treatment time and time to heal and a potential reduction in treatment-related nursing labor costs.

Adsorption of the Three-phase Emulsion on Various Solid Surfaces.

PubMed

Enomoto, Yasutaka; Imai, Yoko; Tajima, Kazuo

2017-07-01

The present study investigates the adsorption of the three-phase emulsion on various solid/water interfaces. Vesicles can be used as emulsifiers in the three-phase emulsions and act as an independent phase unlike the surfactant used in conventional emulsions; therefore, it is expected that the three-phase emulsion formed by the adhesion of vesicles to the oil/water interface will adsorb on various solid/water interfaces. The cationic three-phase emulsion was prepared to encourage emulsion adsorption on negatively charged solid substrates in water. The emulsifier polyoxyethylene-(10) hydrogenated castor oil was rendered cationic by mixing with the surfactant cetyltrimethylammonium bromide and then used to prepare the cationic three-phase emulsion of hexadecane-in-water. Three solid substrates (silicon, glass, and copper) were dipped in the cationic emulsion and the emulsion was found to adsorb on the solid substrates while maintaining its structure. The amount of hexadecane adsorbed on the various surfaces was investigated by gas chromatography and found to increase with increasing hexadecane concentration in the emulsion and eventually plateaued just like molecular adsorption. The maximum surface coverage of the emulsion on the substrates was approximately 80%. However, even the equivalent nonionic three-phase emulsion was found to adsorb on the three solid surfaces. This was attributed to a novel mechanism of irreversible adhesion via the van der Waals attractive force.

Design of Block Copolymer Costabilized Nonionic Microemulsions and Their In Vitro and In Vivo Assessment as Carriers for Sustained Regional Delivery of Ibuprofen via Topical Administration.

PubMed

Djekic, Ljiljana; Martinovic, Martina; Stepanović-Petrović, Radica; Tomić, Maja; Micov, Ana; Primorac, Marija

2015-08-01

Nonionic surfactants (caprylocaproyl macrogol-8 glycerides, octoxynol-12, polysorbate-20, and polyethylene glycol-40 hydrogenated castor oil) (47.03%, w/w), costabilizer (poloxamer 407) (12%-20%, w/w), oil (isopropyl myristate) (5.22%, w/w), water (q.s. ad 100%, w/w), and ibuprofen (5%, w/w) were used to develop oil-in-water microemulsions with Newtonian flow behavior, low viscosity (from 368 ± 38 to 916 ± 46 mPa s), and average droplet size from 14.79 ± 0.31 to 16.54 ± 0.75 nm. Ibuprofen in vitro release from the microemulsions was in accordance with zero-order kinetics (R0(2) > 0.99) for at least 12 h. The maximum drug release rate (3.55%h(-1) ) was from the microemulsion M3 comprising 16%, w/w of poloxamer 407. The release rate of ibuprofen from the reference hydrogel followed Higuchi kinetics (RH(2) > 0.99), and drug amount released after the 6th hour was negligible. In a rat model of inflammation, the microemulsion M3 was significantly more efficacious than the reference hydrogel in exerting antihyperalgesic effects in prophylactic topical treatment, whereas they were comparable in therapeutic treatment as well as in producing antiedematous effect in both protocols. No obvious skin irritation was observed in in vivo studies. The developed nonionic surfactants-based microemulsions containing the optimal concentration of poloxamer 407 could be promising carriers for sustained regional delivery of ibuprofen via topical administration. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

Development and Testing of a Sustained Release System for the Prevention of Malaria.

DTIC Science & Technology

1979-09-01

linear function of time to 100% excretion the extrapolated dur- ation of the control group would be 517 days (203 days/0.393). As used in leprosy ...use in leprosy treatment, the suspending vehicle is 40% benzyl benzoate, 60% castor oil. Solubility of WR-4593 in water is given as 3.0 pg/ml while in

Polyurethane Foams for Thermal Insulation Uses Produced from Castor Oil and Crude Glycerol Biopolyols.

PubMed

Carriço, Camila S; Fraga, Thaís; Carvalho, Vagner E; Pasa, Vânya M D

2017-07-02

Rigid polyurethane foams were synthesized using a renewable polyol from the simple physical mixture of castor oil and crude glycerol. The effect of the catalyst (DBTDL) content and blowing agents in the foams' properties were evaluated. The use of physical blowing agents (cyclopentane and n-pentane) allowed foams with smaller cells to be obtained in comparison with the foams produced with a chemical blowing agent (water). The increase of the water content caused a decrease in density, thermal conductivity, compressive strength, and Young's modulus, which indicates that the increment of CO₂ production contributes to the formation of larger cells. Higher amounts of catalyst in the foam formulations caused a slight density decrease and a small increase of thermal conductivity, compressive strength, and Young's modulus values. These green foams presented properties that indicate a great potential to be used as thermal insulation: density (23-41 kg·m -3 ), thermal conductivity (0.0128-0.0207 W·m -1 ·K -1 ), compressive strength (45-188 kPa), and Young's modulus (3-28 kPa). These biofoams are also environmentally friendly polymers and can aggregate revenue to the biodiesel industry, contributing to a reduction in fuel prices.

Maytenus erythroxylon Reissek (Celastraceae) ethanol extract presents antidiarrheal activity via antimotility and antisecretory mechanisms.

PubMed

Formiga, Rodrigo de Oliveira; Quirino, Zelma Glebya Maciel; Diniz, Margareth de Fátima Formiga Melo; Marinho, Alexsandro Fernandes; Tavares, Josean Fechine; Batista, Leônia Maria

2017-06-28

To investigate the acute toxicity, phytochemical profile, antidiarrheal activity and mechanisms of action of Maytenus erythroxylon ( M. erythroxylon ) ethanol extract. A castor oil-induced diarrhea model was used to evaluate antidiarrheal activity. Intestinal transit and gastric emptying protocols were used to evaluate a possible antimotility effect. K ATP channels, nitric oxide, presynaptic α2-adrenergic and tissue adrenergic receptors were investigated to uncover antimotility mechanisms of action and castor oil-induced enteropooling to elucidate antisecretory mechanisms. All tested doses of the extract (62.5, 125, 250 and 500 mg/kg) possessed antidiarrheal activity, with a significant decrease of the evacuation index. This activity is possibly related to a reduced gastric emptying (125, 250 and 500 mg/kg) and to a decreased percentage of intestinal transit for all tested doses. That last effect seems to be modulated by nitric oxide, K ATP channels and tissue adrenergic receptors. Besides, the extract also presented antisecretory effect due to a decrease of intestinal fluid accumulation. The antidiarrheal effect of M. erythroxylon found in this study involves antimotility and antisecretory mechanisms that may be attributed to the chemical compounds found in this species: saponins, flavonoids, tannins, triterpenes and steroids.

Electroactive polyurethane/siloxane derived from castor oil as a versatile cardiac patch, part I: Synthesis, characterization, and myoblast proliferation and differentiation.

PubMed

Baheiraei, Nafiseh; Gharibi, Reza; Yeganeh, Hamid; Miragoli, Michele; Salvarani, Nicolò; Di Pasquale, Elisa; Condorelli, Gianluigi

2016-03-01

Tissue-engineered cardiac patch aims at regenerating an infarcted heart by improving cardiac function and providing mechanical support to the diseased myocardium. In order to take advantages of electroactivity, a new synthetic method was developed for the introduction of an electroactive oligoaniline into the backbone of prepared patches. For this purpose, a series of electroactive polyurethane/siloxane films containing aniline tetramer (AT) was prepared through sol-gel reaction of trimethoxysilane functional intermediate polyurethane prepolymers made from castor oil and poly(ethylene glycol). Physicochemical, mechanical, and electrical conductivity of samples were evaluated and the recorded results were correlated to their structural characteristics. The optimized films were proved to be biodegradable and have tensile properties suitable for cardiac patch application. The embedded AT moieties in the backbone of the prepared samples preserved their electroactivity with the electrical conductivity in the range of 10 -4 S/cm. The prepared films were compatible with proliferation of C2C12 and had potential for enhancing myotube formation even without external electrical stimulation. © 2015 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 104A: 775-787, 2016. © 2015 Wiley Periodicals, Inc.

Maytenus erythroxylon Reissek (Celastraceae) ethanol extract presents antidiarrheal activity via antimotility and antisecretory mechanisms

PubMed Central

Formiga, Rodrigo de Oliveira; Quirino, Zelma Glebya Maciel; Diniz, Margareth de Fátima Formiga Melo; Marinho, Alexsandro Fernandes; Tavares, Josean Fechine; Batista, Leônia Maria

2017-01-01

AIM To investigate the acute toxicity, phytochemical profile, antidiarrheal activity and mechanisms of action of Maytenus erythroxylon (M. erythroxylon) ethanol extract. METHODS A castor oil-induced diarrhea model was used to evaluate antidiarrheal activity. Intestinal transit and gastric emptying protocols were used to evaluate a possible antimotility effect. KATP channels, nitric oxide, presynaptic α2-adrenergic and tissue adrenergic receptors were investigated to uncover antimotility mechanisms of action and castor oil-induced enteropooling to elucidate antisecretory mechanisms. RESULTS All tested doses of the extract (62.5, 125, 250 and 500 mg/kg) possessed antidiarrheal activity, with a significant decrease of the evacuation index. This activity is possibly related to a reduced gastric emptying (125, 250 and 500 mg/kg) and to a decreased percentage of intestinal transit for all tested doses. That last effect seems to be modulated by nitric oxide, KATP channels and tissue adrenergic receptors. Besides, the extract also presented antisecretory effect due to a decrease of intestinal fluid accumulation. CONCLUSION The antidiarrheal effect of M. erythroxylon found in this study involves antimotility and antisecretory mechanisms that may be attributed to the chemical compounds found in this species: saponins, flavonoids, tannins, triterpenes and steroids. PMID:28706420

21 CFR 186.1551 - Hydrogenated fish oil.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Hydrogenated fish oil. 186.1551 Section 186.1551... as GRAS § 186.1551 Hydrogenated fish oil. (a) Hydrogenated fish oil (CAS Reg. No. 91078-95-4) is a class of oils produced by partial hydrogenation of oils expressed from fish, primarily menhaden, and...

Production of hydrogen, liquid fuels, and chemicals from catalytic processing of bio-oils

DOEpatents

Huber, George W; Vispute, Tushar P; Routray, Kamalakanta

2014-06-03

Disclosed herein is a method of generating hydrogen from a bio-oil, comprising hydrogenating a water-soluble fraction of the bio-oil with hydrogen in the presence of a hydrogenation catalyst, and reforming the water-soluble fraction by aqueous-phase reforming in the presence of a reforming catalyst, wherein hydrogen is generated by the reforming, and the amount of hydrogen generated is greater than that consumed by the hydrogenating. The method can further comprise hydrocracking or hydrotreating a lignin fraction of the bio-oil with hydrogen in the presence of a hydrocracking catalyst wherein the lignin fraction of bio-oil is obtained as a water-insoluble fraction from aqueous extraction of bio-oil. The hydrogen used in the hydrogenating and in the hydrocracking or hydrotreating can be generated by reforming the water-soluble fraction of bio-oil.

Integration of gas chromatography mass spectrometry methods for differentiating ricin preparation methods.

PubMed

Wunschel, David S; Melville, Angela M; Ehrhardt, Christopher J; Colburn, Heather A; Victry, Kristin D; Antolick, Kathryn C; Wahl, Jon H; Wahl, Karen L

2012-05-07

The investigation of crimes involving chemical or biological agents is infrequent, but presents unique analytical challenges. The protein toxin ricin is encountered more frequently than other agents and is found in the seeds of Ricinus communis, commonly known as the castor plant. Typically, the toxin is extracted from castor seeds utilizing a variety of different recipes that result in varying purity of the toxin. Moreover, these various purification steps can also leave or differentially remove a variety of exogenous and endogenous residual components with the toxin that may indicate the type and number of purification steps involved. We have applied three gas chromatography-mass spectrometry (GC-MS) based analytical methods to measure the variation in seed carbohydrates and castor oil ricinoleic acid, as well as the presence of solvents used for purification. These methods were applied to the same samples prepared using four previously identified toxin preparation methods, starting from four varieties of castor seeds. The individual data sets for seed carbohydrate profiles, ricinoleic acid, or acetone amount each provided information capable of differentiating different types of toxin preparations across seed types. However, the integration of the data sets using multivariate factor analysis provided a clear distinction of all samples based on the preparation method, independent of the seed source. In particular, the abundance of mannose, arabinose, fucose, ricinoleic acid, and acetone were shown to be important differentiating factors. These complementary tools provide a more confident determination of the method of toxin preparation than would be possible using a single analytical method.

Mining whole genomes and transcriptomes of Jatropha (Jatropha curcas) and Castor bean (Ricinus communis) for NBS-LRR genes and defense response associated transcription factors.

PubMed

Sood, Archit; Jaiswal, Varun; Chanumolu, Sree Krishna; Malhotra, Nikhil; Pal, Tarun; Chauhan, Rajinder Singh

2014-11-01

Jatropha (Jatropha curcas L.) and Castor bean (Ricinus communis) are oilseed crops of family Euphorbiaceae with the potential of producing high quality biodiesel and having industrial value. Both the bioenergy plants are becoming susceptible to various biotic stresses directly affecting the oil quality and content. No report exists as of today on analysis of Nucleotide Binding Site-Leucine Rich Repeat (NBS-LRR) gene repertoire and defense response transcription factors in both the plant species. In silico analysis of whole genomes and transcriptomes identified 47 new NBS-LRR genes in both the species and 122 and 318 defense response related transcription factors in Jatropha and Castor bean, respectively. The identified NBS-LRR genes and defense response transcription factors were mapped onto the respective genomes. Common and unique NBS-LRR genes and defense related transcription factors were identified in both the plant species. All NBS-LRR genes in both the species were characterized into Toll/interleukin-1 receptor NBS-LRRs (TNLs) and coiled-coil NBS-LRRs (CNLs), position on contigs, gene clusters and motifs and domains distribution. Transcript abundance or expression values were measured for all NBS-LRR genes and defense response transcription factors, suggesting their functional role. The current study provides a repertoire of NBS-LRR genes and transcription factors which can be used in not only dissecting the molecular basis of disease resistance phenotype but also in developing disease resistant genotypes in Jatropha and Castor bean through transgenic or molecular breeding approaches.

78 FR 20029 - Castor Oil, Polymer With Adipic Acid, Linoleic Acid, Oleic Acid and Ricinoleic Acid; Tolerance...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-03

... of pesticide use in residential settings. If EPA is able to determine that a finite tolerance is not... environment. 2. The polymer does contain as an integral part of its composition the atomic elements carbon... impurities, any element other than those listed in 40 CFR 723.250(d)(2)(ii). 4. The polymer is neither...

Phytotoxicity of three plant-based biodiesels, unmodified castor oil, and Diesel fuel to alfalfa (Medicago sativa L.), lettuce (Lactuca sativa L.), radish (Raphanus sativus), and wheatgrass (Triticum aestivum).

PubMed

Bamgbose, Ifeoluwa; Anderson, Todd A

2015-12-01

The wide use of plant-based oils and their derivatives, in particular biodiesel, have increased extensively over the past decade to help alleviate demand for petroleum products and improve the greenhouse gas emissions profile of the transportation sector. Biodiesel is regarded as a clean burning alternative fuel produced from livestock feeds and various vegetable oils. Although in theory these animal and/or plant derived fuels should have less environmental impact in soil based on their simplified composition relative to Diesel, they pose an environmental risk like Diesel at high concentrations when disposed. The aim of the present study was to ascertain the phytotoxicity of three different plant-derived biodiesels relative to conventional Diesel. For phytotoxicological analysis, we used seeds of four crop plants, Medicago sativa, Lactuca sativa, Raphanus sativus, and Triticum aestivum to analyze the germination of seeds in contaminated soil samples. The toxicological experiment was conducted with two different soil textures: sandy loam soil and silt loam soil. The studied plant-based biodiesels were safflower methyl-ester, castor methyl ester, and castor ethyl-ester. Biodiesel toxicity was more evident at high concentrations, affecting the germination and survival of small-seeded plants to a greater extent. Tolerance of plants to the biodiesels varied between plant species and soil textures. With the exception of R. sativus, all plant species were affected and exhibited some sensitivity to the fuels, such as delayed seedling emergence and slow germination (average=10 days) at high soil concentrations (0.85% for Diesel and 1.76% for the biodiesels). Tolerance of plants to soil contamination had a species-specific nature, and on average, decreased in the following order: Raphanus sativus (0-20%)>Triticum aestivum (10-40%) ≥ Medicago sativa> Lactuca sativa (80-100%). Thus, we conclude that there is some phytotoxicity associated with plant-based biodiesels. Further, the findings of this study can be useful for selecting the least fuel-tolerant species as a soil contamination bio-indicator and for determining the risks of biodiesel contamination. Copyright © 2015 Elsevier Inc. All rights reserved.

ROMP-based thermosetting polymers from modified castor oil with various cross-linking agents

NASA Astrophysics Data System (ADS)

Ding, Rui

Polymers derived from bio-renewable resources are finding an increase in global demand. In addition, polymers with distinctive functionalities are required in certain advanced fields, such as aerospace and civil engineering. In an attempt to meet both these needs, the goal of this work aims to develop a range of bio-based thermosetting matrix polymers for potential applications in multifunctional composites. Ring-opening metathesis polymerization (ROMP), which recently has been explored as a powerful method in polymer chemistry, was employed as a unique pathway to polymerize agricultural oil-based reactants. Specifically, a novel norbornyl-functionalized castor oil alcohol (NCA) was investigated to polymerize different cross-linking agents using ROMP. The effects of incorporating dicyclopentadiene (DCPD) and a norbornene-based crosslinker (CL) were systematically evaluated with respect to curing behavior and thermal mechanical properties of the polymers. Isothermal differential scanning calorimetry (DSC) was used to investigate the conversion during cure. Dynamic DSC scans at multiple heating rates revealed conversion-dependent activation energy by Ozawa-Flynn-Wall analysis. The glass transition temperature, storage modulus, and loss modulus for NCA/DCPD and NCA/CL copolymers with different cross-linking agent loading were compared using dynamic mechanical analysis. Cross-link density was examined to explain the very different dynamic mechanical behavior. Mechanical stress-strain curves were developed through tensile test, and thermal stability of the cross-linked polymers was evaluated by thermogravimetric analysis to further investigate the structure-property relationships in these systems.

Quantification of ricin, RCA and comparison of enzymatic activity in 18 Ricinus communis cultivars by isotope dilution mass spectrometry

PubMed Central

Schieltz, David M.; McWilliams, Lisa G.; Kuklenyik, Zsuzsanna; Prezioso, Samantha M.; Carter, Andrew J.; Williamson, Yulanda M.; McGrath, Sara C.; Morse, Stephen A.; Barr, John R.

2016-01-01

The seeds of the Ricinus communis (Castor bean) plant are the source of the economically important commodity castor oil. Castor seeds also contain the proteins ricin and R. communis agglutinin (RCA), two toxic lectins that are hazardous to human health. Radial immunodiffusion (RID) and the enzyme linked immunosorbent assay (ELISA) are two antibody-based methods commonly used to quantify ricin and RCA; however, antibodies currently used in these methods cannot distinguish between ricin and RCA due to the high sequence homology of the respective proteins. In this study, a technique combining antibody-based affinity capture with liquid chromatography and multiple reaction monitoring (MRM) mass spectrometry (MS) was used to quantify the amounts of ricin and RCA independently in extracts prepared from the seeds of eighteen representative cultivars of R. communis which were propagated under identical conditions. Additionally, liquid chromatography and MRM-MS was used to determine rRNA N-glycosidase activity for each cultivar and the overall activity in these cultivars was compared to a purified ricin standard. Of the cultivars studied, the average ricin content was 9.3 mg/g seed, the average RCA content was 9.9 mg/g seed, and the enzymatic activity agreed with the activity of a purified ricin reference within 35% relative activity. PMID:25576235

21 CFR 186.1551 - Hydrogenated fish oil.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Hydrogenated fish oil. 186.1551 Section 186.1551... Listing of Specific Substances Affirmed as GRAS § 186.1551 Hydrogenated fish oil. (a) Hydrogenated fish... from fish, primarily menhaden, and secondarily herring or tuna. Hydrogenation of fish oils uses...

21 CFR 186.1551 - Hydrogenated fish oil.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Hydrogenated fish oil. 186.1551 Section 186.1551... Listing of Specific Substances Affirmed as GRAS § 186.1551 Hydrogenated fish oil. (a) Hydrogenated fish... from fish, primarily menhaden, and secondarily herring or tuna. Hydrogenation of fish oils uses...

46 CFR 148.235 - Castor beans.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 5 2014-10-01 2014-10-01 false Castor beans. 148.235 Section 148.235 Shipping COAST... THAT REQUIRE SPECIAL HANDLING Special Requirements for Certain Materials § 148.235 Castor beans. (a) This part applies only to the stowage and transportation of whole castor beans. Castor meal, castor...

46 CFR 148.235 - Castor beans.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 5 2012-10-01 2012-10-01 false Castor beans. 148.235 Section 148.235 Shipping COAST... THAT REQUIRE SPECIAL HANDLING Special Requirements for Certain Materials § 148.235 Castor beans. (a) This part applies only to the stowage and transportation of whole castor beans. Castor meal, castor...

46 CFR 148.235 - Castor beans.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 5 2011-10-01 2011-10-01 false Castor beans. 148.235 Section 148.235 Shipping COAST... THAT REQUIRE SPECIAL HANDLING Special Requirements for Certain Materials § 148.235 Castor beans. (a) This part applies only to the stowage and transportation of whole castor beans. Castor meal, castor...

46 CFR 148.235 - Castor beans.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 5 2013-10-01 2013-10-01 false Castor beans. 148.235 Section 148.235 Shipping COAST... THAT REQUIRE SPECIAL HANDLING Special Requirements for Certain Materials § 148.235 Castor beans. (a) This part applies only to the stowage and transportation of whole castor beans. Castor meal, castor...

Influence of phase inversion on the formation and stability of one-step multiple emulsions.

PubMed

Morais, Jacqueline M; Rocha-Filho, Pedro A; Burgess, Diane J

2009-07-21

A novel method of preparation of water-in-oil-in-micelle-containing water (W/O/W(m)) multiple emulsions using the one-step emulsification method is reported. These multiple emulsions were normal (not temporary) and stable over a 60 day test period. Previously, reported multiple emulsion by the one-step method were abnormal systems that formed at the inversion point of simple emulsion (where there is an incompatibility in the Ostwald and Bancroft theories, and typically these are O/W/O systems). Pseudoternary phase diagrams and bidimensional process-composition (phase inversion) maps were constructed to assist in process and composition optimization. The surfactants used were PEG40 hydrogenated castor oil and sorbitan oleate, and mineral and vegetables oils were investigated. Physicochemical characterization studies showed experimentally, for the first time, the significance of the ultralow surface tension point on multiple emulsion formation by one-step via phase inversion processes. Although the significance of ultralow surface tension has been speculated previously, to the best of our knowledge, this is the first experimental confirmation. The multiple emulsion system reported here was dependent not only upon the emulsification temperature, but also upon the component ratios, therefore both the emulsion phase inversion and the phase inversion temperature were considered to fully explain their formation. Accordingly, it is hypothesized that the formation of these normal multiple emulsions is not a result of a temporary incompatibility (at the inversion point) during simple emulsion preparation, as previously reported. Rather, these normal W/O/W(m) emulsions are a result of the simultaneous occurrence of catastrophic and transitional phase inversion processes. The formation of the primary emulsions (W/O) is in accordance with the Ostwald theory ,and the formation of the multiple emulsions (W/O/W(m)) is in agreement with the Bancroft theory.

Effect of glyphosate on the castor plant Ricinus communis L

USDA-ARS?s Scientific Manuscript database

The presence of a toxin in the castor seed has been a major impediment to the reintroduction of castor as a domestic crop in the US. Because dehiscent forms of castor are invasive and castor seed remains viable for years under the right conditions, there is concern that if castor were widely cultiva...

MUSAC II: A Method for Modeling Passive Sonar Classification in a Multiple Target Environment.

DTIC Science & Technology

1976-02-01

TERAIN #46-6667 - Green (chlorophyll Type) (Parts by Weight) Cantor Wax 21.6 Carnauba Wax 3.1 Mineral Oil, U.S.P.Heavy 22.5 lanolin, U.S.P. angdrous 10.5...MMOSITICt - PAINT, FACE, CAMOUF1AGE, ARID TURAIN #23-6667-Lom #21-6667-Sand (Parts by weight) (Parts by weight) Castor Wax 17.5 17.5 CartAuba Wax 2.5

Relationship between the antidiarrhoeal effects of Hange-Shashin-To and its active components.

PubMed

Kase, Y; Saitoh, K; Makino, B; Hashimoto, K; Ishige, A; Komatsu, Y

1999-09-01

This study was designed to examine the relationship between the antidiarrhoeal effects of Hange-Shashin-To (TJ-14) and its active components. Oral treatment with TJ-14 at 1000 mg/kg significantly inhibited castor oil-induced diarrhoea. Both the 50% methanol eluate fraction (fraction III) and the methanol eluate fraction (fraction IV) showed antidiarrhoeal effects at oral doses of 68 mg/kg and 63 mg/kg, respectively, corresponding to 1000 mg/kg of TJ-14. TJ-14 (1000 mg/kg, p.o.) showed a significant increase in blood corticosterone levels. Increased blood corticosterone was noted after the oral administration of 63 mg/kg of fraction IV. The inhibitory activity of TJ-14 on cyclooxygenase-2 (COX-2) was also observed in fractions III and IV. The main component of fraction III was Scutellariae Radix-derived baicalin. Fraction IV contained Glycyrrhizae Radix-derived glycyrrhizin and isoliquiritin, Coptidis Rhizoma-derived berberine, coptisine and palmitine. Ginseng Radix-derived saponins were also present in fraction IV. These compounds inhibited castor-oil induced diarrhoea at oral doses of 10 or 30 mg/kg. Thus, the present results indicate that Scutellariae Radix, Glycyrrhizae Radix, Ginseng radix and Coptidis Rhizoma-derived components are involved in the antidiarrhoeal action of TJ-14. Copyright 1999 John Wiley & Sons, Ltd.

Cytotoxicity and genotoxicity of natural resin-based experimental endodontic sealers.

PubMed

Silva, Gleyce O; Cavalcanti, Bruno N; Oliveira, Tatiana R; Bin, Claudia V; Camargo, Samira E A; Camargo, Carlos H R

2016-05-01

The development of endodontic sealers based on natural resins seems to be promising, given their improved biological properties. This study evaluated the cytotoxic and genotoxic effects of two experimental root canal sealers, based on extracts from Copaifera multijuga and Ricinus communis (castor oil polymer), comparing them to synthetic resin-based sealers: a single methacrylate-based, a multi-methacrylate-based, and an epoxy resin-based sealers. Sealers were prepared, set, and exposed to cell culture medium for 24 h at 37 °C with CO2. V79 cells were exposed to serial dilutions of the extracts of each sealer for 24 h. Cell viability was measured by the MTT assay and genotoxicity was assessed by the formation of micronuclei. The single methacrylate-based sealer had the most cytotoxic effects, with significant reduction in cell viability in all dilutions of the extract. The castor oil polymer-based sealer was, on the other hand, the most biocompatible sealer, with no cytotoxic effects at any concentration. All tested sealers were not genotoxic, excepting the single methacrylate-based sealer. The tested natural resin-based sealers presented low cytotoxic and no genotoxic effects on cell cultures. These results may suggest a good alternative to develop new endodontic sealers, in order to achieve better biological response and healing, when compared to commercially available sealers.

Solubility of ocular therapeutic agents in self-emulsifying oils. I. Self-emulsifying oils for ocular drug delivery: solubility of indomethacin, aciclovir and hydrocortisone.

PubMed

Czajkowska-Kośnik, Anna; Sznitowska, Małgorzata

2009-01-01

Self-emulsifying drug delivery systems (SEDDS) were prepared by dissolving Cremophor EL, Tween 20, Tween 80 and Span 80 (1% or 5%) in oils (Miglyol 812 or castor oil). Solubilities of three ophthalmic drugs, namely aciclovir, hydrocortisone and indomethacin were determined in these systems. In addition, the effect of a small amount of water (0.5% and 2%) on solubilization properties of the systems was estimated. Of the three substances, indomethacin showed the best solubility in Miglyol while aciclovir was practically insoluble in this oil. The surfactants usually increased drug solubility in the oily phase. Only Tween 20 was found to decrease the solubility of aciclovir and hydrocortisone in Miglyol. Addition of a small amount of water to the oil/surfactant system increased solubility of hydrocortisone, but not of indomethacin. The results of the current study may be utilized to design a suitable composition of SEDDS and allow continuation of research on this type of drug carriers.

Effects of poly(lactic-co-glycolic acid) on preparation and characteristics of plasmid DNA-loaded solid lipid nanoparticles.

PubMed

Zhu, L; Xie, S; Dong, Z; Wang, X; Wang, Y; Zhou, W

2011-09-01

Poly(lactic-co-glycolic acid) (PLGA) was used as a polymeric emulsifier to encapsulate plasmid DNA into hydrogenated castor oil (HCO)-solid lipid nanoparticles (SLN) by w/o/w double emulsion and solvent evaporation techniques. The effects of PLGA on the preparation, characteristics and transfection efficiency of DNA-loaded SLN were studied. The results showed that PLGA was essential to form the primary w/o emulsion and the stability of the emulsion was enhanced with the increase of PLGA content. DNA-loaded SLN were spherical with smooth surfaces. The SLN had a negative charge in weak acid and alkaline environment but acquired a positive charge in acidic pH and the cationisation capacity of the SLN increased with the increase of PLGA/HCO ratio. Agarose gel electrophoresis demonstrated that the majority of the DNA maintained its structural integrity after preparation and being extracted or released from DNA-loaded SLN. When PLGA/HCO ratio increased from 5 to 15%, the encapsulation efficiency, loading capacity and transfection efficiency of the nanoparticles increased significantly, whereas the changes of particle size and polydispersity index were insignificant. Cytotoxicity study in cell culture demonstrated that the SLN was not toxic.

Effects of poly (lactic-co-glycolic acid) as a co-emulsifier on the preparation and hypoglycaemic activity of insulin-loaded solid lipid nanoparticles.

PubMed

Wang, S L; Xie, S Y; Zhu, L Y; Wang, F H; Zhou, W Z

2009-12-01

Poly (lactic-co-glycolic acid) (PLGA) was used as a co-emulsifier in the preparation of insulin-loaded solid lipid nanoparticles (SLN) with hydrogenated castor oil as lipid matrix and lecithin as surfactant by double-emulsion technique. The effects of PLGA on the preparation and hypoglycaemic activity of insulin-loaded SLN were studied. The results showed that with the supplement of PLGA, the encapsulation efficiency and loading capacity were increased significantly from 79.08 +/- 1.62 to 85.57 +/- 3.21% and 1.58 +/- 0.03 to 1.71 +/- 0.06%, whereas the surface charge and particle size were changed insignificantly from -25.87 +/- 2.65 to -22.67 +/- 1.19 mv and 431.0 +/- 16.1 to 397.0 +/- 68.0 nm, respectively. In vivo studies demonstrated that PLGA increased the sustained hypoglycaemic activity from 12 to 36 h and 24 to 120 h in normal and steptozotocin-induced diabetic mice after a single intramuscular injection of the insulin-loaded SLN. These results demonstrated that PLGA could enhance the entrapment of insulin in the nanoparticles, and more importantly, prolong the time of hypoglycaemic activity of the insulin-loaded SLN.

Bio-oil Stabilization by Hydrogenation over Reduced Metal Catalysts at Low Temperatures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Huamin; Lee, Suh-Jane; Olarte, Mariefel V.

Biomass fast pyrolysis integrated with bio-oil upgrading represents a very attractive approach for converting biomass to hydrocarbon transportation fuels. However, the thermal and chemical instability of bio-oils presents significant problems when they are being upgraded, and development of effective approaches for stabilizing bio-oils is critical to the success of the technology. Catalytic hydrogenation to remove reactive species in bio-oil has been considered as one of the most efficient ways to stabilize bio-oil. This paper provides a fundamental understanding of hydrogenation of actual bio-oils over a Ru/TiO2 catalyst under conditions relevant to practical bio-oil hydrotreating processes. Bio-oil feed stocks, bio-oils hydrogenatedmore » to different extents, and catalysts have been characterized to provide insights into the chemical and physical properties of these samples and to understand the correlation of the properties with the composition of the bio-oil and catalysts. The results indicated hydrogenation of various components of the bio-oil, including sugars, aldehydes, ketones, alkenes, aromatics, and carboxylic acids, over the Ru/TiO2 catalyst and 120 to 160oC. Hydrogenation of these species significantly changed the chemical and physical properties of the bio-oil and overall improved its thermal stability, especially by reducing the carbonyl content, which represented the content of the most reactive species (i.e., sugar, aldehydes, and ketones). The change of content of each component in response to increasing hydrogen additions suggests the following bio-oil hydrogenation reaction sequence: sugar conversion to sugar alcohols, followed by ketone and aldehyde conversion to alcohols, followed by alkene and aromatic hydrogenation, and then followed by carboxylic acid hydrogenation to alcohols. Hydrogenation of bio-oil samples with different sulfur contents or inorganic material contents suggested that sulfur poisoning of the reduced Ru metal catalysts was significant during hydrogenation; however, the inorganics at low concentrations had minimal impact at short times on stream, indicating that sulfur poisoning was the primary deactivation mode for the bio-oil hydrogenation catalyst. Reducing the sulfur content in bio-oil could significantly increase the lifetime of the hydrogenation catalyst used. The knowledge gained during this work will allow rational design of more effective catalysts and processes for stabilizing and upgrading bio-oils.« less

Isolation and characterization of biosurfactant production under extreme environmental conditions by alkali-halo-thermophilic bacteria from Saudi Arabia

PubMed Central

Elazzazy, Ahmed M.; Abdelmoneim, T.S.; Almaghrabi, O.A.

2014-01-01

Twenty three morphologically distinct microbial colonies were isolated from soil and sea water samples, which were collected from Jeddah region, Saudi Arabia for screening of the most potent biosurfactant strains. The isolated bacteria were selected by using different methods as drop collapse test, oil displacement test, blue agar test, blood hemolysis test, emulsification activity and surface tension. The results showed that the ability of Virgibacillus salarius to grow and reduce surface tension under a wide range of pH, salinities and temperatures gives bacteria isolate an advantage in many applications such as pharmaceutical, cosmetics, food industries and bioremediation in marine environment. The biosurfactant production by V. salarius decreased surface tension and emulsifying activity (30 mN/m and 80%, respectively). In addition to reducing the production cost of biosurfactants by tested several plant-derived oils such as jatropha oil, castor oils, jojoba oil, canola oil and cottonseed oil. In this respect the feasibility to reusing old frying oil of sunflower for production rhamnolipids and sophorolipids, their use that lead to solve many ecological and industrial problems. PMID:26150754

Isolation and characterization of biosurfactant production under extreme environmental conditions by alkali-halo-thermophilic bacteria from Saudi Arabia.

PubMed

Elazzazy, Ahmed M; Abdelmoneim, T S; Almaghrabi, O A

2015-07-01

Twenty three morphologically distinct microbial colonies were isolated from soil and sea water samples, which were collected from Jeddah region, Saudi Arabia for screening of the most potent biosurfactant strains. The isolated bacteria were selected by using different methods as drop collapse test, oil displacement test, blue agar test, blood hemolysis test, emulsification activity and surface tension. The results showed that the ability of Virgibacillus salarius to grow and reduce surface tension under a wide range of pH, salinities and temperatures gives bacteria isolate an advantage in many applications such as pharmaceutical, cosmetics, food industries and bioremediation in marine environment. The biosurfactant production by V. salarius decreased surface tension and emulsifying activity (30 mN/m and 80%, respectively). In addition to reducing the production cost of biosurfactants by tested several plant-derived oils such as jatropha oil, castor oils, jojoba oil, canola oil and cottonseed oil. In this respect the feasibility to reusing old frying oil of sunflower for production rhamnolipids and sophorolipids, their use that lead to solve many ecological and industrial problems.

Field evaluation of commercial repellents against the floodwater mosquito Psorophora columbiae (Diptera: Culicidae) in St. Johns County, Florida.

PubMed

Qualls, Whitney A; Xue, Rui-De; Holt, J Adam; Smith, Mike L; Moeller, Jeanne J

2011-11-01

Three plant-based repellents-REPEL LEMON Eucalyptus Insect Repellent Lotion (active ingredient [AI] 30% oil of eucalyptus), Bite Blocker Xtreme Sportsman Organic Insect Repellent ([AI] 3% soybean oil, 6% geranium oil, and 8% castor oil), and Bite Blocker BioUD Insect Repellent ([AI] 7.75% 2-undecanone)--were evaluated against OFF! ([AI] 15% N,N-diethyl-m-toluamide or N,N-diethyl-3-methyl-benzamide, also called DEET) at a field site in Elkton, FL, to determine the mean protection time provided against Psorophora columbiae (Dyar & Knab). These products provided different protection times against biting Ps. columbiae. REPEL provided the longest protection time (330 min) followed by Bite Blocker Xtreme Sportsman (163 min), Bite Blocker BioUD (140 min), and OFF! (130 min). This study provides the first information about plant-based insect repellent protection times against Ps. columbiae.

Novel depots of buprenorphine have a long-acting effect for the management of physical dependence to morphine.

PubMed

Liu, Kuo-Sheng; Kao, Cheng-Hsiung; Liu, Shyun-Yeu; Sung, K C; Kuei, Chun-Hsiung; Wang, Jhi-Joung

2006-03-01

Buprenorphine is a promising new pharmacotherapy for the management of physical dependence to opioids. The aim of the study was to evaluate the duration of action of several novel depots of buprenorphine in the treatment of physical dependence to morphine in mice. Following intramuscular injection, the duration of action of several novel oil-based depots of buprenorphine base in morphine-dependent mice were evaluated. The traditional dosage form of buprenorphine hydrochloride in saline was used as control. We found that the depot of buprenorphine base in sesame oil produced a dose-related long-lasting effect. On an equimolar basis of 6 micromol kg(-1), its effect was 5.7-fold longer than that of buprenorphine hydrochloride in saline. When prepared in several other oleaginous vehicles (castor oil, cottonseed oil, peanut oil and soybean oil), buprenorphine base also produced a long-lasting effect, which was similar to buprenorphine base in sesame oil. In conclusion, buprenorphine base, when prepared in oleaginous vehicles and injected intramuscularly in mice, produced a long-lasting effect on physical dependence to morphine.

Determination of Wetting Behavior, Spread Activation Energy, and Quench Severity of Bioquenchants

NASA Astrophysics Data System (ADS)

Prabhu, K. Narayan; Fernandes, Peter

2007-08-01

An investigation was conducted to study the suitability of vegetable oils such as sunflower, coconut, groundnut, castor, cashewnut shell (CNS), and palm oils as quench media (bioquenchants) for industrial heat treatment by assessing their wetting behavior and severity of quenching. The relaxation of contact angle was sharp during the initial stages, and it became gradual as the system approached equilibrium. The equilibrium contact angle decreased with increase in the temperature of the substrate and decrease in the viscosity of the quench medium. A comparison of the relaxation of the contact angle at various temperatures indicated the significant difference in spreading of oils having varying viscosity. The spread activation energy was determined using the Arrhenius type of equation. Oils with higher viscosity resulted in lower cooling rates. The quench severity of various oil media was determined by estimating heat-transfer coefficients using the lumped capacitance method. Activation energy for spreading determined using the wetting behavior of oils at various temperatures was in good agreement with the severity of quenching assessed by cooling curve analysis. A high quench severity is associated with oils having low spread activation energy.

Photosynthetic capacity and water use efficiency in Ricinus communis (L.) under drought stress in semi-humid and semi-arid areas.

PubMed

Santos, Claudiana M Dos; Endres, Laurício; Ferreira, Vilma M; Silva, José V; Rolim, Eduardo V; Wanderley, Humberto C L

2017-01-01

Castor bean is one of the crops with potential to provide raw material for production of oils for biodiesel. This species possess adaptive mechanisms for maintaining the water status when subjected to drought stress. A better understanding these mechanisms under field conditions can unravel the survival strategies used by this species. This study aimed to compare the physiological adaptations of Ricinus communis (L.) in two regions with different climates, the semi-arid and semi-humid subject to water stress. The plants showed greater vapor pressure deficit during the driest hours of the day, which contributed to higher values of the leaf temperature and leaf transpiration, however, the VPD(leaf-air) had the greatest effect on plants in the semi-arid region. In both regions, between 12:00 p.m. and 2:00 p.m., the plants presented reduction in the rates of photosynthesis and intracellular CO2 concentration in response to stomatal closure. During the dry season in the semi-arid region, photoinhibition occurred in the leaves of castor bean between 12:00 p.m. and 2:00 p.m. These results suggest that castor bean plants possess compensatory mechanisms for drought tolerance, such as: higher stomatal control and maintenance of photosynthetic capacity, allowing the plant to survive well in soil with low water availability.

Quantification of ricin, RCA and comparison of enzymatic activity in 18 Ricinus communis cultivars by isotope dilution mass spectrometry.

PubMed

Schieltz, David M; McWilliams, Lisa G; Kuklenyik, Zsuzsanna; Prezioso, Samantha M; Carter, Andrew J; Williamson, Yulanda M; McGrath, Sara C; Morse, Stephen A; Barr, John R

2015-03-01

The seeds of the Ricinus communis (Castor bean) plant are the source of the economically important commodity castor oil. Castor seeds also contain the proteins ricin and R. communis agglutinin (RCA), two toxic lectins that are hazardous to human health. Radial immunodiffusion (RID) and the enzyme linked immunosorbent assay (ELISA) are two antibody-based methods commonly used to quantify ricin and RCA; however, antibodies currently used in these methods cannot distinguish between ricin and RCA due to the high sequence homology of the respective proteins. In this study, a technique combining antibody-based affinity capture with liquid chromatography and multiple reaction monitoring (MRM) mass spectrometry (MS) was used to quantify the amounts of ricin and RCA independently in extracts prepared from the seeds of eighteen representative cultivars of R. communis which were propagated under identical conditions. Additionally, liquid chromatography and MRM-MS was used to determine rRNA N-glycosidase activity for each cultivar and the overall activity in these cultivars was compared to a purified ricin standard. Of the cultivars studied, the average ricin content was 9.3 mg/g seed, the average RCA content was 9.9 mg/g seed, and the enzymatic activity agreed with the activity of a purified ricin reference within 35% relative activity. Published by Elsevier Ltd.

Hyaluronic acid coated poly-epsilon-caprolactone nanospheres deliver high concentrations of cyclosporine A into the cornea.

PubMed

Yenice, Irem; Mocan, Mehmet C; Palaska, Erhan; Bochot, Amélie; Bilensoy, Erem; Vural, Imran; Irkeç, Murat; Hincal, A Atilla

2008-09-01

The objective of this study was to determine cyclosporine A (Cy A) levels in ocular tissues and fluids after topical administration of poly-epsilon-caprolactone (PCL)/benzalkonium chloride (BKC) nanospheres and hyaluronic acid (HA) coated PCL/BKC nanospheres onto healthy rabbit corneas. Nanospheres were prepared by nanoprecipitation and purified by gradient-rate centrifugation. Cy A (0.1%) in either castor oil solution (group 1), PCL/BKC nanosphere formulation (group 2) or HA coated PCL/BKC nanosphere formulation (group 3) was instilled onto rabbit corneas. Tear samples were adsorbed onto Schirmer tear strips. Cy A concentrations of fluid (blood, aqueous humor, tear) and specimen extracts (cornea, conjunctiva, iris/ciliary body) were determined by high performance liquid chromatography-mass spectrometry (LC-MS). The mean corneal Cy A concentration obtained at 0.5, 1, 2, 4, 8 and 24h following instillation of the formulations ranged between 0.12 and 1.2 ng/mg tissue for group 1, 5.9-15.5 ng/mg tissue for group 2 and 11.4-23.0 ng/mg for group 3 (one-way analysis of variance (ANOVA) and pairwise tests (SNK (Student-Newman-Keuls) and Tukey); p<0.05). Conjunctival Cy A levels of group 2 and 3 were not significantly different at any of the time points tested. However, there was a significant difference between Cy A concentration of castor oil formulation and that of PCL/BKC nanosphere formulation at 1 and 8h (p<0.05). The mean iris/ciliary body concentrations obtained with the three formulations were not significantly different at any time point with the exception of group 2 levels being higher than those of groups 1 and 3 at 1h (p<0.05). The lowest ocular tear Cy A concentrations (16-114 ng/ml) were found following the instillation of HA coated PCL/BKC nanoparticles (group 3) during the time period tested. Cy A loaded PCL/BKC and HA coated PCL/BKC nanospheres are able to achieve high levels of Cy A in the cornea that is 10-15-fold higher than that is achieved with Cy A solution in castor oil. Nanosphere formulation and HA may play an important role in delivering high levels of cyclosporine A into the cornea.

Responses of beaver (Castor canadensis Kuhl) to predator chemicals.

PubMed

Engelhart, A; Müller-Schwarze, D

1995-09-01

Free-ranging beaver (Castor canadensis) in two different beaver populations in New York State were exposed to predator chemicals to test feeding inhibition. Solvent extracts of feces were applied to stem sections of aspen, the preferred food tree of beavers, permitting smelling and tasting the samples. Predator odors were from wolf (Canis lupus), coyote (Canis latrans), dog (Canis familiaris), black bear (Ursus americanus), river otter (Lutra canadensis), lynx (Lynx canadensis), and African lion (Panthera leo). The experiment was repeated. The predator odors reduced feeding compared to untreated or solvent-treated controls. One population consumed 17.0% of the samples with predator odor and 27.0% of the controls in summer, and 48.4% and 60.0%, respectively, in autumn. The other population accepted 3.15% of the predator odor samples and 11.05% of the controls in summer. Coyote, lynx, and river otter odors had the strongest effects. Diesel oil and bitter-tasting neem extract had weaker effects. Predator odors are promising as feeding repellents for beaver.

Biocompatibility of Ricinus communis polymer with addition of calcium carbonate compared to titanium. Experimental study in guinea pigs

PubMed Central

Graça, Yorgos Luiz Santos De Salles; Opolski, Ana Cristina; Barboza, Barbara Evelin Gonçalves; Erbano, Bruna Olandoski; Mazzaro, Caroline Cantalejo; Klostermann, Flávia Caroline; Sucharski, Enéas Eduardo; Kubrusly, Luiz Fernando

2014-01-01

Objective The aim of the present investigation was to determine whether the difference in inflammatory tissue reaction between the Riccinus communis (castor) polymer with calcium carbonate and the titanium implant is statistically significant. Methods Thirty-two Cavia porcellus were allocated into four groups of eight animals each. We implanted the two types of materials in the retroperitoneal space of all the animals. They were euthanized at 7, 20, 30 and 40 days after surgery, and an histological study of the samples was conducted. Results All implants showed characteristics of chronic inflammation regardless of the material and timepoint of evaluation. There was no statistically significant difference between Pm+CaCO3 and Ti with regard to the presence of granulation tissue, tissue congestion, histiocytes, lymphocytes, neutrophils, giant cells, and fibrosis (P> 0.05). Conclusion The castor oil polymer plus calcium carbonate implant was not statistically different from the titanium implant regarding inflammatory tissue reaction. PMID:25140479

Proposed Use of the Computer as a Tool to Aid Analysis of Properties of Materials in Fixators of Spine

PubMed Central

Santos, Antonio; Moreira, Fernando

2014-01-01

With objective of analyzing the mechanical behavior of the internal fixators of spine and of the bony structure, the pieces and the group were made (it structures bony x internal fixator) with the aid a software of solid modeling. The materials used in the rehearsals had been the titanium, now in the market and a castor oil polyurethane destined to the development of you implant bony. PMID:24825938

Effect of the incorporation of chitosan on the physico-chemical, mechanical properties and biological activity on a mixture of polycaprolactone and polyurethanes obtained from castor oil.

PubMed

Arévalo, Fabian; Uscategui, Yomaira L; Diaz, Luis; Cobo, Martha; Valero, Manuel F

2016-11-01

In the present study, polyurethane materials were obtained from castor oil, polycaprolactone and isophorone diisocyanate by incorporating different concentrations of chitosan (0.5, 1.0 and 2.0% w/w) as an additive to improve the mechanical properties and the biological activity of polyurethanes. The polyurethanes were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy, stress/strain fracture tests and swelling analysis, and the hydrophilic character of the surface was determined by contact angle trials. The objectives of the study were to evaluate the effect of the incorporation of chitosan on the changes of the physico-chemical and mechanical properties and the in vitro biological activity of the polyurethanes. It was found that the incorporation of chitosan enhances the ultimate tensile strength of the polyurethanes and does not affect the strain at fracture in polyurethanes with 5% w/w of polycaprolactone and concentrations of chitosan ranging from 0 to 2% w/w. In addition, PCL5-Q-PU formulations and their degradation products did not affect cell viability of L929 mouse fibroblast and 3T3, respectively. Polyurethane formulations showed antibacterial activities against Staphylococcus aureus and Escherichia coli bacteria. The results of this study have highlighted the potential biomedical application of this polyurethanes related to soft and cardiovascular tissues. © The Author(s) 2016.

Primary Swenson's pull-through in children with chronic constipation: a preliminary report.

PubMed

Bakare Tajudeen, I B; Badmus, T A; Lawal, A O; Katung, A I

2010-01-01

The discrepancy in diameters of the resected ends coupled with the heavy faecal loads in the colon of chronically constipated children with Hirschsprung's disease makes definitive primary pull-through procedure quite difficulty in this group. Four consecutive patients (aged 5 months to 11 years) who presented with chronic constipation were given warm saline enema along with Castor oil per oram twice daily for 1 week before and 2 weeks after full-thickness biopsies that confirmed Hirschsprung's disease. All patients had intravenous Cefuroxime or Ceftriaxone plus Metronidazole at induction of anaesthesia. Intra-operatively, the levels of resections were 6-8 cm proximal to the most contractile part of the colon adjacent to the transition zone observed after complete division of mesenteric vessels. There were three males and one female, aged 5 months to 11 years. The levels of aganglionosis were in the rectosigmoid region, except one in the descending colon. There was one case each of anastomotic stenoses, mild enterocolitis and deep peri-anal excoriation. The bowel motions were two to four times daily within 1 month post-operatively. It can be concluded from this preliminary study that with pre-operative saline enema and oral Castor oil for about 3 weeks in chronically constipated children with Hirschsprung's disease primary pull-through procedures can be performed successfully. However, further prospective work is required with this method.

Effect of skin coatings on prolonging shelf life of kagzi lime fruits (Citrus aurantifolia Swingle).

PubMed

Bisen, Abhay; Pandey, Sailendra Kumar; Patel, Neha

2012-12-01

An experiment was conducted to assess the influence of chemical and oil coatings on storage life of kagzi lime fruits. Fruits were harvested at physiological light green mature stage and treated with different concentrations of chemicals viz., Cacl2 and KMnO4 and edible coatings viz., (coconut oil, mustard oil, sesamum oil, castor oil and liquid paraffin wax). After treatment, fruits were kept at ambient condition (25-30 °C, 60-70% RH) till 18 days and analyzed for various physical and chemical parameters like PLW, marketable fruits retained, TSS, acidity, ascorbic acid, juice content and also organoleptic values. The results revealed that edible oil emulsion coating particularly coconut oil had significantly (p ≤ 0.05) effect on reduction of the physiological loss in weight (9.67%) and maximum marketable fruits retained (70%), total soluble solids (8.43%), ascorbic acid (49.93 mg/100 ml juice), acidity (1.52%) and juice content (42.34%) of fruits. Similarly, application of this oil emulsion coating acceptable for sensory quality parameters such as appearance, flavour, taste, external colour and no incidence of moulds & their growth up to 18 days of storage.

49 CFR 172.604 - Emergency response telephone number.

Code of Federal Regulations, 2010 CFR

2010-10-01

... vehicle. Carbon dioxide, solid. Castor bean. Castor flake. Castor meal. Castor pomace. Consumer commodity. Dry ice. Engines, internal combustion. Fish meal, stabilized. Fish scrap, stabilized. Refrigerating machine. Vehicle, flammable gas powered. Vehicle, flammable liquid powered. Wheelchair, electric. (3...

Process for obtaining liquid fuel-oil and/or gaseous hydrocarbons from solid carbonaceous feed stocks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hollaway, J.W.

1978-02-28

A process for forming a fuel-oil from coal is disclosed. The coal is treated in a low temperature carbonization retort to give coke, coal-gas and tar-oil. The coke is converted to water-gas which is then synthesized in a Fischer-Tropsch synthesizer to form fuel-oil. The tar-oil is hydrogenated in a hydro-treater by hydrogen produced from the coal-gas. Hydrogen is produced from coal-gas either in a thermal cracking chamber or by reforming the methane content to hydrogen and passing the resultant hydrogen/carbon monoxide mixture through a water-gas shift reactor and a carbon dioxide scrubber.

Palladium catalyzed hydrogenation of bio-oils and organic compounds

DOEpatents

Elliott, Douglas C [Kennewick, WA; Hu, Jianli [Richland, WA; Hart,; Todd, R [Kennewick, WA; Neuenschwander, Gary G [Burbank, WA

2011-06-07

The invention provides palladium-catalyzed hydrogenations of bio-oils and certain organic compounds. Experimental results have shown unexpected and superior results for palladium-catalyzed hydrogenations of organic compounds typically found in bio-oils.

Palladium catalyzed hydrogenation of bio-oils and organic compounds

DOEpatents

Elliott, Douglas C [Richland, WA; Hu, Jianli [Kennewick, WA; Hart, Todd R [Kennewick, WA; Neuenschwander, Gary G [Burbank, WA

2008-09-16

The invention provides palladium-catalyzed hydrogenations of bio-oils and certain organic compounds. Experimental results have shown unexpected and superior results for palladium-catalyzed hydrogenations of organic compounds typically found in bio-oils.

Materials for Slack Diaphragms

NASA Technical Reports Server (NTRS)

Puschmann, Traute

1940-01-01

This report deals with systematic experiments carried out on five diaphragm materials with different pretreatment, for the purpose of ascertaining the suitability of such materials for slack diaphragms. The relationship of deflection and load, temperature and moisture, was recorded. Of the explored materials, synthetic leather, balloon cloth, goldbeaters skin, Igelit and Buna, synthetic leather treated with castor oil is the most suitable material for the small pressure range required. Balloon cloth is nearly as good, while goldbeaters skin, Igelit and Buna were found to be below the required standards.

The role of viscosity estimation for oil-in-gelatin phantom in shear wave based ultrasound elastography.

PubMed

Zhu, Ying; Dong, Changfeng; Yin, Yin; Chen, Xin; Guo, Yanrong; Zheng, Yi; Shen, Yuanyuan; Wang, Tianfu; Zhang, Xinyu; Chen, Siping

2015-02-01

Shear wave based ultrasound elastography utilizes mechanical excitation or acoustic radiation force to induce shear waves in deep tissue. The tissue response is monitored to obtain elasticity information about the tissue. During the past two decades, tissue elasticity has been extensively studied and has been used in clinical disease diagnosis. However, biological soft tissues are viscoelastic in nature. Therefore, they should be simultaneously characterized in terms of elasticity and viscosity. In this study, two shear wave-based elasticity imaging methods, shear wave dispersion ultrasound vibrometry (SDUV) and acoustic radiation force impulsive (ARFI) imaging, were compared. The discrepancy between the measurements obtained by the two methods was analyzed, and the role of viscosity was investigated. To this end, four types of gelatin phantoms containing 0%, 20%, 30% and 40% castor oil were fabricated to mimic different viscosities of soft tissue. For the SDUV method, the shear elasticity μ1 was 3.90 ± 0.27 kPa, 4.49 ± 0.16 kPa, 2.41 ± 0.33 kPa and 1.31 ± 0.09 kPa; and the shear viscosity μ2 was 1.82 ± 0.31 Pa•s, 2.41 ± 0.35 Pa•s, 2.65 ± 0.13 Pa•s and 2.89 ± 0.14 Pa•s for 0%, 20%, 30% and 40% oil, respectively in both cases. For the ARFI measurements, the shear elasticity μ was 7.30 ± 0.20 kPa, 8.20 ± 0.31 kPa, 7.42 ± 0.21 kPa and 5.90 ± 0.36 kPa for 0%, 20%, 30% and 40% oil, respectively. The SDUV results demonstrated that the elasticity first increased from 0% to 20% oil and then decreased for the 30% and 40% oil. The viscosity decreased consistently as the concentration of castor oil increased from 0% to 40%. The elasticity measured by ARFI showed the same trend as that of the SDUV but exceeded the results measured by SDUV. To clearly validate the impact of viscosity on the elasticity estimation, an independent measurement of the elasticity and viscosity by dynamic mechanical analysis (DMA) was conducted on these four types of gelatin phantoms and then compared with SDUV and ARFI results. The shear elasticities obtained by DMA (3.44 ± 0.31 kPa, 4.29 ± 0.13 kPa, 2.05 ± 0.29 kPa and 1.06 ± 0.18 kPa for 0%, 20%, 30% and 40% oil, respectively) were lower than those by SDUV, whereas the shear viscosities obtained by DMA (2.52 ± 0.32 Pa·s, 3.18 ± 0.12 Pa·s, 3.98 ± 0.19 Pa·s and 4.90 ± 0.20 Pa·s for 0%, 20%, 30% and 40% oil, respectively) were greater than those obtained by SDUV. However, the DMA results showed that the trend in the elasticity and viscosity data was the same as that obtained from the SDUV and ARFI. The SDUV results demonstrated that adding castor oil changed the viscoelastic properties of the phantoms and resulted in increased dispersion of the shear waves. Viscosity can provide important and independent information about the inner state of the phantoms, in addition to the elasticity. Because the ARFI method ignores the dispersion of the shear waves, namely viscosity, it may bias the estimation of the true elasticity. This study sheds further light on the significance of the viscosity measurements in shear wave based elasticity imaging methods. Copyright © 2015 World Federation for Ultrasound in Medicine & Biology. Published by Elsevier Inc. All rights reserved.

21 CFR 184.1555 - Rapeseed oil.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Rapeseed oil. 184.1555 Section 184.1555 Food and....1555 Rapeseed oil. (a) Fully hydrogenated rapeseed oil. (1) Fully hydrogenated rapeseed oil is a... occurring in natural rapeseed oil. The rapeseed oil is obtained from the napus and campestris varieties of...

Encapsulation of Naproxen in Lipid-Based Matrix Microspheres: Characterization and Release Kinetics

PubMed Central

Bhoyar, PK; Morani, DO; Biyani, DM; Umekar, MJ; Mahure, JG; Amgaonkar, YM

2011-01-01

The objective of this study was to microencapsulate the anti-inflammatory drug (naproxen) to provide controlled release and minimizing or eliminating local side effect by avoiding the drug release in the upper gastrointestinal track. Naproxen was microencapsulated with lipid-like carnauba wax, hydrogenated castor oil using modified melt dispersion (modified congealable disperse phase encapsulation) technique. Effect of various formulation and process variables such as drug-lipid ratio, concentration of modifier, concentration of dispersant, stirring speed, stirring time, temperature of external phase, on evaluatory parameters such as size, entrapment efficiency, and in vitro release of naproxen were studied. The microspheres were characterized for particle size, scanning electron microscopy (SEM), FT-IR spectroscopy, drug entrapment efficiency, in vitro release studies, for in vitro release kinetics. The shape of microspheres was found to be spherical by SEM. The drug entrapment efficiency of various batches of microspheres was found to be ranging from 60 to 90 %w/w. In vitro drug release studies were carried out up to 24 h in pH 7.4 phosphate buffer showing 50-65% drug release. In vitro drug release from all the batches showed better fitting with the Korsmeyer-Peppas model, indicating the possible mechanism of drug release to be by diffusion and erosion of the lipid matrix. PMID:21731354

Encapsulation of naproxen in lipid-based matrix microspheres: characterization and release kinetics.

PubMed

Bhoyar, P K; Morani, D O; Biyani, D M; Umekar, M J; Mahure, J G; Amgaonkar, Y M

2011-04-01

The objective of this study was to microencapsulate the anti-inflammatory drug (naproxen) to provide controlled release and minimizing or eliminating local side effect by avoiding the drug release in the upper gastrointestinal track. Naproxen was microencapsulated with lipid-like carnauba wax, hydrogenated castor oil using modified melt dispersion (modified congealable disperse phase encapsulation) technique. Effect of various formulation and process variables such as drug-lipid ratio, concentration of modifier, concentration of dispersant, stirring speed, stirring time, temperature of external phase, on evaluatory parameters such as size, entrapment efficiency, and in vitro release of naproxen were studied. The microspheres were characterized for particle size, scanning electron microscopy (SEM), FT-IR spectroscopy, drug entrapment efficiency, in vitro release studies, for in vitro release kinetics. The shape of microspheres was found to be spherical by SEM. The drug entrapment efficiency of various batches of microspheres was found to be ranging from 60 to 90 %w/w. In vitro drug release studies were carried out up to 24 h in pH 7.4 phosphate buffer showing 50-65% drug release. In vitro drug release from all the batches showed better fitting with the Korsmeyer-Peppas model, indicating the possible mechanism of drug release to be by diffusion and erosion of the lipid matrix.

Preparation of buccal patch composed of carbopol, poloxamer and hydroxypropyl methylcellulose.

PubMed

Chun, Myung-Kwan; Kwak, Byoung-Tae; Choi, Hoo-Kyun

2003-11-01

A polymeric film composed of Carbopol, Poloxamer and hydroxypropyl methylcellulose was prepared to develop a buccal patch and the effects of composition of the film on adhesion time, swelling ratio, and dissolution of the film were studied. The effects of plasticizers or penetration enhancers on the release of triamcinolone acetonide (TAA) were also studied. The hydrogen bonding between Carbopol and Poloxamer played important role in reducing swelling ratio and dissolution rate of polymer film and increasing adhesion time. The swelling ratio of the composite film was significantly reduced and the adhesion time was increased when compared with Carbopol film. As the ratio of Poloxamer to hydroxypropyl methylcellulose increased from 0/66 to 33/33, the release rate of TAA decreased. However, no further significant decrease of release rate was observed beyond the ratio of 33/33. The release rate of TAA in the polymeric film containing polyethylene glycol 400, a plasticizer, showed the highest release rate followed by triethyl citrate, and castor oil. The release rate of TAA from the polymeric film containing permeation enhancers was slower than that from the control without enhancers. Therefore, these observations indicated that a preparation of a buccal patch is feasible with the polymeric film composed of Cabopol, Poloxamer and hydropropyl methylcellulose.

Effect of PLGA as a polymeric emulsifier on preparation of hydrophilic protein-loaded solid lipid nanoparticles.

PubMed

Xie, ShuYu; Wang, SiLiang; Zhao, BaoKai; Han, Chao; Wang, Ming; Zhou, WenZhong

2008-12-01

Most proteins are hydrophilic and poorly encapsulated into the hydrophobic matrix of solid lipid nanoparticles (SLN). To solve this problem, poly (lactic-co-glycolic acid) (PLGA) was utilized as a lipophilic polymeric emulsifier to prepare hydrophilic protein-loaded SLN by w/o/w double emulsion and solvent evaporation techniques. Hydrogenated castor oil (HCO) was used as a lipid matrix and bovine serum albumin (BSA), lysozyme and insulin were used as model proteins to investigate the effect of PLGA on the formulation of the SLN. The results showed that PLGA was essential for the primary w/o emulsification. In addition, the stability of the w/o emulsion, the encapsulation efficiency and loading capacity of the nanoparticles were enhanced with the increase of PLGA concentration. Furthermore, increasing PLGA concentration decreased zeta potential significantly but had no influence on particle size of the SLN. In vitro release study showed that PLGA significantly affected the initial burst release, i.e. the higher the content of PLGA, the lower the burst release. The released proteins maintained their integrity and bioactivity as confirmed by sodium dodecyl sulphate-polyacrylamide gel electrophoresis (SDS-PAGE) and biological assay. These results demonstrated that PLGA was an effective emulsifier for the preparation of hydrophilic protein-loaded SLN.

Comparison of soybean and cottonseed oils upon hydrogenation with nickel, palladium and platinum catalysts

USDA-ARS?s Scientific Manuscript database

There is current interest in reducing the trans fatty acids (TFA) in hydrogenated vegetable oils because consumption of foods high in TFA has been linked to increased serum cholesterol content. In this work, hydrogenation was carried out on soybean oil and cottonseed oil at two pressures (2 and 5 b...

Shock Hugoniot and equations of states of water, castor oil, and aqueous solutions of sodium chloride, sucrose and gelatin

NASA Astrophysics Data System (ADS)

Gojani, A. B.; Ohtani, K.; Takayama, K.; Hosseini, S. H. R.

2016-01-01

This paper reports a result of experiments for the determination of reliable shock Hugoniot curves of liquids, in particular, at relatively low pressure region, which are needed to perform precise numerical simulations of shock wave/tissue interaction prior to the development of shock wave related therapeutic devices. Underwater shock waves were generated by explosions of laser ignited 10 mg silver azide pellets, which were temporally and spatially well controlled. Measuring temporal variation of shock velocities and over-pressures in caster oil, aqueous solutions of sodium chloride, sucrose and gelatin with various concentrations, we succeeded to determine shock Hugoniot curves of these liquids and hence parameters describing Tait type equations of state.

Hydrogenation and interesterification effects on the oxidative stability and melting point of soybean oil.

PubMed

Daniels, Roger L; Kim, Hyun Jung; Min, David B

2006-08-09

Soybean oil with an iodine value of 136 was hydrogenated to have iodine values of 126 and 117. The soybean oils with iodine values of 136, 126, and 117 were randomly interesterified using sodium methoxide. The oxidative stabilities of the hydrogenated and/or interesterified soybean oils were evaluated by measuring the headspace oxygen content by gas chromatography, and the induction time was measured using Rancimat. The melting points of the oils were evaluated by differential scanning calorimetry. Duncan's multiple range test of the headspace oxygen and induction time showed that hydrogenation increased the headspace oxygen content and induction time at alpha = 0.05. Interesterification decreased the headspace oxygen and the induction time for the soybean oils with iodine values of 136, 126, and 117 at alpha = 0.05. Hydrogenation increased the melting points as the iodine value decreased from 136 and 126 to 117 at alpha = 0.05. The random interesterification increased the melting points of soybean oils with iodine values of 136, 126, and 117 at alpha = 0.05. The combined effects of hydrogenation and interesterification increased the oxidative stability of soybean oil at alpha = 0.05 and the melting point at alpha = 0.01. The optimum combination of hydrogenation and random interesterification can improve the oxidative stability and increase the melting point to expand the application of soybean oil in foods.

Food grade microemulsion systems: Sunflower oil/castor oil derivative-ethanol/water. Rheological and physicochemical analysis.

PubMed

Mori Cortés, Noelia; Lorenzo, Gabriel; Califano, Alicia N

2018-05-01

Microemulsions are thermodynamically stable systems that have attracted considerable attention in the food industry as delivery systems for many hydrophobic nutrients. These spontaneous systems are highly dependent on ingredients and composition. In this work phase diagrams were constructed using two surfactants (Kolliphor RH40 and ELP), water, sunflower oil, and ethanol as cosurfactant, evaluating their physicochemical properties. Stability of the systems was studied at 25 and 60 °C, monitoring turbidity at 550 nm for over a month to identify the microemulsion region. Conductivity was measured to classify between water-in-oil and oil-in-water microemulsions. The phase diagram constructed with Kolliphor RH40 exhibited a larger microemulsion area than that formulated with Kolliphor ELP. All formulations showed a monomodal droplet size distribution with low polydispersity index (<0.30) and a mean droplet size below 20 nm. Systems with higher water content presented a Newtonian behavior; increasing the dispersed phase content produced a weak gel-like structure with pseudoplastic behavior under flow conditions that was satisfactorily modeled to obtain structural parameters. Copyright © 2018 Elsevier Ltd. All rights reserved.

Minimising hydrogen sulphide generation during steam assisted production of heavy oil

PubMed Central

Montgomery, Wren; Sephton, Mark A.; Watson, Jonathan S.; Zeng, Huang; Rees, Andrew C.

2015-01-01

The majority of global petroleum is in the form of highly viscous heavy oil. Traditionally heavy oil in sands at shallow depths is accessed by large scale mining activities. Recently steam has been used to allow heavy oil extraction with greatly reduced surface disturbance. However, in situ thermal recovery processes can generate hydrogen sulphide, high levels of which are toxic to humans and corrosive to equipment. Avoiding hydrogen sulphide production is the best possible mitigation strategy. Here we use laboratory aquathermolysis to reproduce conditions that may be experienced during thermal extraction. The results indicate that hydrogen sulphide generation occurs within a specific temperature and pressure window and corresponds to chemical and physical changes in the oil. Asphaltenes are identified as the major source of sulphur. Our findings reveal that for high sulphur heavy oils, the generation of hydrogen sulphide during steam assisted thermal recovery is minimal if temperature and pressure are maintained within specific criteria. This strict pressure and temperature dependence of hydrogen sulphide release can allow access to the world's most voluminous oil deposits without generating excessive amounts of this unwanted gas product. PMID:25670085

Minimising hydrogen sulphide generation during steam assisted production of heavy oil

NASA Astrophysics Data System (ADS)

Montgomery, Wren; Sephton, Mark A.; Watson, Jonathan S.; Zeng, Huang; Rees, Andrew C.

2015-02-01

The majority of global petroleum is in the form of highly viscous heavy oil. Traditionally heavy oil in sands at shallow depths is accessed by large scale mining activities. Recently steam has been used to allow heavy oil extraction with greatly reduced surface disturbance. However, in situ thermal recovery processes can generate hydrogen sulphide, high levels of which are toxic to humans and corrosive to equipment. Avoiding hydrogen sulphide production is the best possible mitigation strategy. Here we use laboratory aquathermolysis to reproduce conditions that may be experienced during thermal extraction. The results indicate that hydrogen sulphide generation occurs within a specific temperature and pressure window and corresponds to chemical and physical changes in the oil. Asphaltenes are identified as the major source of sulphur. Our findings reveal that for high sulphur heavy oils, the generation of hydrogen sulphide during steam assisted thermal recovery is minimal if temperature and pressure are maintained within specific criteria. This strict pressure and temperature dependence of hydrogen sulphide release can allow access to the world's most voluminous oil deposits without generating excessive amounts of this unwanted gas product.

Minimising hydrogen sulphide generation during steam assisted production of heavy oil.

PubMed

Montgomery, Wren; Sephton, Mark A; Watson, Jonathan S; Zeng, Huang; Rees, Andrew C

2015-02-11

The majority of global petroleum is in the form of highly viscous heavy oil. Traditionally heavy oil in sands at shallow depths is accessed by large scale mining activities. Recently steam has been used to allow heavy oil extraction with greatly reduced surface disturbance. However, in situ thermal recovery processes can generate hydrogen sulphide, high levels of which are toxic to humans and corrosive to equipment. Avoiding hydrogen sulphide production is the best possible mitigation strategy. Here we use laboratory aquathermolysis to reproduce conditions that may be experienced during thermal extraction. The results indicate that hydrogen sulphide generation occurs within a specific temperature and pressure window and corresponds to chemical and physical changes in the oil. Asphaltenes are identified as the major source of sulphur. Our findings reveal that for high sulphur heavy oils, the generation of hydrogen sulphide during steam assisted thermal recovery is minimal if temperature and pressure are maintained within specific criteria. This strict pressure and temperature dependence of hydrogen sulphide release can allow access to the world's most voluminous oil deposits without generating excessive amounts of this unwanted gas product.

Biochar prepared from castor oil cake at different temperatures: A voltammetric study applied for Pb(2+), Cd(2+) and Cu(2+) ions preconcentration.

PubMed

Kalinke, Cristiane; Mangrich, Antonio Sálvio; Marcolino-Junior, Luiz H; Bergamini, Márcio F

2016-11-15

Biochar is a carbonaceous material similar produced by pyrolysis of biomass under oxygen-limited conditions. Pyrolysis temperature is an important parameter that can alters biochar characteristics (e.g. surface area, pore size distribution and surface functional groups) and affects it efficacy for adsorption of several probes. In this work, biochar samples have been prepared from castor oil cake using different temperatures of pyrolysis (200-600°C). For the first time, a voltammetric procedure based on carbon paste modified electrode (CPME) was used to investigate the effect of temperature of pyrolysis on the adsorptive characteristics of biochar for Pb(II), Cd(II) and Cu(II) ions. Besides the electrochemical techniques, several characterizations have been performed to evaluate the physicochemical properties of biochar in function of the increase of the pyrolysis temperature. Results suggest that biochar pyrolized at 400°C (BC400) showed a better potential for ions adsorption. The CPME modified with BC400 showed better relative current signal with adsorption affinity: Pb(II)>Cd(II)>Cu(II). Kinetic studies revealed that the pseudo-second order model describes more accurately the adsorption process suggesting that the surface reactions control the adsorption rate. Values found for amount adsorbed were 15.94±0.09; 4.29±0.13 and 2.38±0.39μgg(-1) for Pb(II), Cd(II) and Cu(II) ions, respectively. Copyright © 2016 Elsevier B.V. All rights reserved.

Research on High Sensitive D-Shaped FBG Hydrogen Sensors in Power Transformer Oil

PubMed Central

Luo, Ying-Ting; Wang, Hong-Bin; Ma, Guo-Ming; Song, Hong-Tu; Li, Chengrong; Jiang, Jun

2016-01-01

Dissolved hydrogen is a symbol gas decomposed by power transformer oil for electrical faults such as overheat or partial discharges. A novel D-shaped fiber Bragg grating (D-FBG) sensor is herein proposed and was fabricated with magnetron sputtering to measure the dissolved hydrogen concentration in power transformer oil in this paper. Different from the RI (refractive index)-based effect, D-FBG in this case is sensitive to curvature caused by stress from sensing coating, leading to Bragg wavelength shifts accordingly. The relationship between the D-FBG wavelength shift and dissolved hydrogen concentration in oil was measured experimentally in the laboratory. The detected sensitivity could be as high as 1.96 μL/L at every 1-pm wavelength shift. The results proved that a simple, polished FBG-based hydrogen sensor provides a linear measuring characteristic in the range of low hydrogen concentrations in transformer oil. Moreover, the stable hydrogen sensing performance was investigated by X-ray diffraction analysis. PMID:27782034

Research on High Sensitive D-Shaped FBG Hydrogen Sensors in Power Transformer Oil.

PubMed

Luo, Ying-Ting; Wang, Hong-Bin; Ma, Guo-Ming; Song, Hong-Tu; Li, Chengrong; Jiang, Jun

2016-10-04

Dissolved hydrogen is a symbol gas decomposed by power transformer oil for electrical faults such as overheat or partial discharges. A novel D-shaped fiber Bragg grating (D-FBG) sensor is herein proposed and was fabricated with magnetron sputtering to measure the dissolved hydrogen concentration in power transformer oil in this paper. Different from the RI (refractive index)-based effect, D-FBG in this case is sensitive to curvature caused by stress from sensing coating, leading to Bragg wavelength shifts accordingly. The relationship between the D-FBG wavelength shift and dissolved hydrogen concentration in oil was measured experimentally in the laboratory. The detected sensitivity could be as high as 1.96 μL/L at every 1-pm wavelength shift. The results proved that a simple, polished FBG-based hydrogen sensor provides a linear measuring characteristic in the range of low hydrogen concentrations in transformer oil. Moreover, the stable hydrogen sensing performance was investigated by X-ray diffraction analysis.

Investigation of damping liquids for aircraft instruments

NASA Technical Reports Server (NTRS)

Keulegan, G H

1929-01-01

This report covers the results of an investigation carried on at the Bureau of Standards under a research authorization from, and with the financial assistance of, the National Advisory Committee for Aeronautics. The choice of a damping liquid for aircraft instruments is difficult owing to the range of temperature at which aircraft operate. Temperature changes affect the viscosity tremendously. The investigation was undertaken with the object of finding liquids of various viscosities otherwise suitable which had a minimum change in viscosity with temperature. The new data relate largely to solutions. The effect of temperature on the kinematic viscosity of the following liquids and solutions was determined in the temperature interval -18 degrees to +30 degrees C. (1) solutions of animal and vegetable oils in xylene. These were poppy-seed oil, two samples of neat's-foot oils, castor oil, and linseed oil. (2) solutions of mineral oil in xylene. These were Squibb's petrolatum of naphthene base and transformer oil. (3) glycerine solutions in ethyl alcohol and in mixture of 50-50 ethyl alcohol and water. (4) mixtures of normal butyl alcohol with methyl alcohol. (5) individual liquids, kerosene, mineral spirits, xylene, recoil oil. The apparatus consisted of four capillary-tube viscometers, which were immersed in a liquid bath in order to secure temperature control. The method of calibration and the related experimental data are presented.

High-resolution Kendrick Mass Defect Analysis of Poly(ethylene oxide)-based Non-ionic Surfactants and Their Degradation Products.

PubMed

Fouquet, Thierry; Shimada, Haruo; Maeno, Katsuyuki; Ito, Kanako; Ozeki, Yuka; Kitagawa, Shinya; Ohtani, Hajime; Sato, Hiroaki

2017-09-01

Matrix assisted laser desorption ionization (MALDI) high-resolution mass spectrometry (HRMS) and the recently introduced high-resolution Kendrick mass defect (HRKMD) analysis are combined to thoroughly characterize non-ionic surfactants made of a poly(ethylene oxide) (PEO) core capped by esters of fatty acids. A PEO monostearate surfactant is first analyzed as a proof of principle of the HRKMD analysis conducted with a fraction of EO as the base unit (EO/X with X being an integer) in lieu of EO for a regular KMD analysis. Data visualization is greatly enhanced and the distributions detected in the MALDI mass spectrum are assigned to a pristine (H, OH)-PEO as well as mono- and di-esterified PEO chains with palmitate and stearate end-groups in HRKMD plots computed with EO/45. The MALDI-HRMS/HRKMD analysis is then successfully applied to the more complex case of ethoxylated hydrogenated castor oil (EHCO) found to contain a large number of hydrogenated ricinoleate moieties (up to 14) in its HRKMD plot computed with EO/43, departing from the expected triglyceride structure. The exhaustiveness of the MALDI-HRMS/HRKMD strategy is validated by comparing the so-obtained fingerprints with results from alternative techniques (electrospray ionization MS, size exclusion and liquid adsorption chromatography, ion mobility spectrometry). Finally, aged non-ionic surfactants formed upon hydrolytic degradation are analyzed by MALDI-HRMS/HRKMD to easily assign the degradation products and infer the associated degradation routes. In addition to the hydrolysis of the ester groups observed for EHCO, chain scissions and new polar end-groups are observed in the HRKMD plot of PEO monostearate arising from a competitive oxidative ageing.

Applications of polymer coatings for the fabrication of copper-based containers for the ultimate disposal of Canada's spent nuclear fuel

NASA Astrophysics Data System (ADS)

Mortley, Aba

Oxygen-free, phosphorous doped copper containers have been proposed for the storage of the used nuclear fuel bundles as a part of Canada's multi-barrier, adaptive phased management procedure for long term storage of spent nuclear fuel bundles. The spent nuclear fuel disposal system proposed for Canada has been engineered based on the multi-barrier approach intended to minimize the risk that the radioactive materials enter the biosphere. Copper is known to be susceptible to corrosion and it is thought that the simultaneous exposure to aggressive ionizing radiation field and residual heat produced by the spent nuclear fuel and the surrounding groundwater would all challenge the container's integrity. The goal of the present work is to reduce the impact of corrosion in the early stages of emplacement with the addition of a protective coating. Specifically, castor oil based polyurethanes were assessed as coatings and their ability to act as an additional physical barrier in the multi-barrier system mentioned previously. The novelty of this work stems from the use of a naturally derived non-petroleum based material in the form of castor oil as the polyol component. Two types of castor oil polyurethanes were investigated, one based on an aliphatic hexamethylene diisocyanate (HMDI), and the other based on an aromatic 2,4-toluene diisocyanate (TDI). Radiation and saturation tests were conducted using varying conditions. Mixed field ionizing radiation was provided by a SLOWPOKE-2 pool-type nuclear research reactor, up to accumulated doses of 6 MGy at dose rates of 37 kGy h-1 and 55.5 kGy h-1. Weight gain immersion studies, at temperatures of 25° C, 50° C, 70° C, were used to determine the mass uptake of several different solutions. The solutions utilized in the present work included hydrochloric acids of varying pHs, distilled water, and buffered solutions, which simulated chloride and sulphide rich calcium-sodium bicarbonate waters. After being exposed to radiation and saturation individually and in several combinations, the polymer samples were tested using a battery of tests. These tests were used to determine how the physico-mechanical properties of the materials, such as their strength, and their ability to be deformed and stretched were affected by radiation. The gist of these tests being that, if the sample showed significant variations in the physico-mechanical properties, then the material would be deemed as unacceptable for use in combined radiation-temperature-pH environments of the deep geological repository (DGR). The tests used included: Fourier transform infrared spectroscopy (FTIR), Matrix-assisted laser desorption/ionization (MALDI) spectroscopy, electronic ionization mass spectroscopy (EI MS), wide angle x-ray scattering (WAXS), solid-state nuclear magnetic resonance ( 13C-NMR), dynamic mechanical analysis (DMA), and differential scanning calorimetry (DSC). Radiation dose increases from 0 MGy to 2.0 MGy showed a four-fold increase from 0.930 MPa to 4.365 MPa in the initial modulus and 0.149 MPa to 0.747 MPa in the tensile strength values of the polyurethanes. Above 2.0 MGy, the modulus and the tensile strength values exhibited a plateau at values above those of the unirradiated samples. The sorption and diffusion experiments demonstrated a mass uptake of less than 2 %, regardless of what polar solution was used. As a reflection of the more rigid polymer matrix provided by the aromatic ring, the aromatic polyurethanes generally exhibited higher modulus and tensile strength values and lower solution mass uptake and diffusivities. The diffusion values ranged from 8.5 x 10-7 cm2 s-1 to 3.31 X 10-6 cm2 s -1 for the aliphatic polyurethanes and 8.8 x 10-7 cm 2 s-1 to 1.60 x 10-6 cm2 S-1 for the aromatic polyurethanes. The order in which the experimental conditions were applied, Le. sequentially or simultaneously, had definite effects on the finished product. However, regardless of the manner in which the radiation and saturation were combined, in a sequential or simultaneous manner, the end results showed that the moduli values remained above those of the virgin samples (> 2 MPa). The results of the present work indicate that the castor oil based polyurethanes may indeed be used as a viable material where the end-use conditions include combined radiation-thermal-pH environments such as part of the container to store used nuclear fuel. Future development on this work can look at how the adhesive qualities between the castor oil based polyurethanes and the metal copper container may change in such environments.

Comparison of effects of soft margarine, blended, ghee, and unhydrogenated oil with hydrogenated oil on serum lipids: A randomized clinical trail

PubMed Central

Mohammadifard, Noushin; Hosseini, Mohsen; Sajjadi, Firoozeh; Maghroun, Maryam; Boshtam, Maryam; Nouri, Fatemeh

2013-01-01

BACKGROUND Trans fatty acids (TFAs) are known as the most harmful type of dietary fats. Therefore, this study was done to compare the effects of some different oils including unhydrogenated, blended, ghee, and soft magazine with hydrogenated oil on serum lipid profile of healthy adults. METHODS This study was a randomized clinical trial conducted on 206 healthy participants of 20 to 60 years of age. Subjects were randomly divided into 5 groups and each of them was treated with a diet containing unhydrogenated oil, ghee, blended oil, soft margarine, or hydrogenated oil for 40 days. Fasting serum lipids were measured before and after the study. RESULTS Compared to hydrogenated oil, total cholesterol (TC) and triglyceride (TG) had a significant reduction in all groups, LDL-C declined in unhydrogenated oil and soft margarine groups, and apolipoprotein (Apo) B only in unhydrogenated oil group (all P < 0.05). However, there was a significant enhancement in ApoA of ghee oil (P < 0.001). CONCLUSION Consuming unhydrogenated oil, ghee, soft margarine, and blended oil had some beneficial effects on serum lipids. PMID:24575140

[Progress in bio-based polyamides].

PubMed

Huang, Zhengqiang; Cui, Zhe; Zhang, Heming; Fu, Peng; Zhao, Qingxiang; Liu, Minying

2016-06-25

Bio-based polyamides are environment-friendly polymers. The precursors of bio-based polyamides come from bio-based materials such as castor oil, glucose and animal oil. Bio-based polyamides precursors include bio-based amino acids, bio-based lactams, bio-based diprotic acid and bio-based diamines. In this paper, we discussed the route of the precursors of bio-based polyamides that come from bio-based materials. We discussed the properties of bio-based polyamides. Bio-based PA11and bio-based PA1010 are well-known bio-based polyamides; we discussed the origin materials of the precursors, the route of manufacturing bio-based PA11 and PA1010, and their modifications status. The variety, classification and commercial production of bio-based polyamides were described in details, as well as bio-based polyamides development in China.

The Development of a High-Power, Low-Frequency Underwater Acoustic Source for Use in a Deep-Towed Geophysical Array Section

DTIC Science & Technology

1982-11-15

Metca) for each ring 6 Aluminum orirlce end ring 15 Rubber bumpers 7 Back plate inner boot ring 16 Castor oil rill-fluid I ’)-ring %eals I ’ Nikel ...electrode .ab% with hook-up wire -ig. 6 - Sectional v-icw orf ISRI) typc (662 tran.dhcer 9 YOUNG, TIMS. AND HENRIQUFZ 0.42 m. Approximately 85% of the...electrical leads for each ring are routed to individual bulkhead connectors on the trans- ducer back plate with high-voltage silicone-jacketed hookup wire

21 CFR 184.1555 - Rapeseed oil.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Rapeseed oil. 184.1555 Section 184.1555 Food and... Substances Affirmed as GRAS § 184.1555 Rapeseed oil. (a) Fully hydrogenated rapeseed oil. (1) Fully hydrogenated rapeseed oil is a mixture of triglycerides in which the fatty acid composition is a mixture of...

21 CFR 184.1555 - Rapeseed oil.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Rapeseed oil. 184.1555 Section 184.1555 Food and... Substances Affirmed as GRAS § 184.1555 Rapeseed oil. (a) Fully hydrogenated rapeseed oil. (1) Fully hydrogenated rapeseed oil is a mixture of triglycerides in which the fatty acid composition is a mixture of...

Chemical Investigations of the Castor Bean Plant Ricinus communis

DTIC Science & Technology

2012-12-01

of the castor bean plant Ricinus communis. A major focus of this grant was to understand the chemical composition of the seeds, and to ascertain if...UNCLASSIFIED Chemical Investigations of the Castor Bean Plant Ricinus communis Simon P. B. Ovenden, Christina K. Bagas, David J...investigation of several forensic aspects of the castor bean plant Ricinus communis. A major focus of this grant was to understand the chemical

Catalytic transfer hydrogenation for stabilization of bio-oil oxygenates: reduction of p-cresol and furfural over bimetallic Ni-Cu catalysts using isopropanol

USDA-ARS?s Scientific Manuscript database

Transfer hydrogenation and hydrodeoxygenation of model bio-oil compounds (p-cresol and furfural) and bio-oils derived from biomass via traditional pyrolysis and tail-gas reactive pyrolysis (TGRP) were conducted. Mild batch reaction conditions were employed, using isopropanol as a hydrogen donor over...

49 CFR 172.327 - Petroleum sour crude oil in bulk packaging.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Bulk packaging used to transport petroleum crude oil containing hydrogen sulfide (i.e., sour crude oil... hydrogen sulfide vapors may occur. (b) The border of the square-on-point must be black or red on a white or...., manhole, loading head) where exposure to hydrogen sulfide vapors may occur. The label, tag, or sign must...

49 CFR 172.327 - Petroleum sour crude oil in bulk packaging.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Bulk packaging used to transport petroleum crude oil containing hydrogen sulfide (i.e., sour crude oil... hydrogen sulfide vapors may occur. (b) The border of the square-on-point must be black or red on a white or...., manhole, loading head) where exposure to hydrogen sulfide vapors may occur. The label, tag, or sign must...

49 CFR 172.327 - Petroleum sour crude oil in bulk packaging.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Bulk packaging used to transport petroleum crude oil containing hydrogen sulfide (i.e., sour crude oil... hydrogen sulfide vapors may occur. (b) The border of the square-on-point must be black or red on a white or...., manhole, loading head) where exposure to hydrogen sulfide vapors may occur. The label, tag, or sign must...

The CASTOR proteins are arginine sensors for the mTORC1 pathway

PubMed Central

Chantranupong, Lynne; Scaria, Sonia M.; Saxton, Robert A.; Gygi, Melanie P.; Shen, Kuang; Wyant, Gregory A.; Wang, Tim; Harper, J. Wade; Gygi, Steven P.; Sabatini, David M.

2016-01-01

Amino acids signal to the mTOR complex I (mTORC1) growth pathway through the Rag GTPases. Multiple distinct complexes regulate the Rags, including GATOR1, a GTPase activating protein (GAP), and GATOR2, a positive regulator of unknown molecular function. Arginine stimulation of cells activates mTORC1, but how it is sensed is not well understood. Recently, SLC38A9 was identified as a putative lysosomal arginine sensor required for arginine to activate mTORC1 but how arginine deprivation represses mTORC1 is unknown. Here, we show that CASTOR1, a previously uncharacterized protein, interacts with GATOR2 and is required for arginine deprivation to inhibit mTORC1. CASTOR1 homodimerizes and can also heterodimerize with the related protein, CASTOR2. Arginine disrupts the CASTOR1-GATOR2 complex by binding to CASTOR1 with a dissociation constant of ~30 μM, and its arginine-binding capacity is required for arginine to activate mTORC1 in cells. Collectively, these results establish CASTOR1 as an arginine sensor for the mTORC1 pathway. PMID:26972053

Nonhydrogenated cottonseed oil can be used as a deep fat frying medium to reduce trans-fatty acid content in french fries.

PubMed

Daniel, Darla R; Thompson, Leslie D; Shriver, Brent J; Wu, Chih-Kang; Hoover, Linda C

2005-12-01

The purpose of this research study was to evaluate the fatty acid profile, in particular trans-fatty acids, of french fries fried in nonhydrogenated cottonseed oil as compared with french fries fried in partially hydrogenated canola oil and french fries fried in partially hydrogenated soybean oil. Cottonseed oil, partially hydrogenated canola oil, and partially hydrogenated soybean oil were subjected to a temperature of 177 degrees C for 8 hours per day, and six batches of french fries were fried per day for 5 consecutive days. French fries were weighed before frying, cooked for 5 minutes, allowed to drain, and reweighed. Oil was not replenished and was filtered once per day. Both the oil and the french fries were evaluated to determine fatty acid profiles, trans-fatty acids, and crude fat. A randomized block design with split plot was used to analyze the data collected. Least-squares difference was used as the means separation test. No significant differences were found between fries prepared in the three oil types for crude fat. Fatty acid profiles for the french fries remained stable. The french fries prepared in cottonseed oil were significantly lower in trans-fatty acids. The combined total of the trans-fatty acid content and saturated fatty acid content were lower in french fries prepared in cottonseed oil. Because deep fat frying remains a popular cooking technique, health professionals should educate the public and the food service industry on the benefits of using nonhydrogenated cottonseed oil as an alternative to the commonly used hydrogenated oils.

21 CFR 184.1555 - Rapeseed oil.

Code of Federal Regulations, 2010 CFR

2010-04-01

... hydrogenated rapeseed oil is a mixture of triglycerides in which the fatty acid composition is a mixture of saturated fatty acids. The fatty acids are present in the same porportions which result from the full hydrogenation of fatty acids occurring in natural rapeseed oil. The rapeseed oil is obtained from the napus and...

Performance and Emission Characteristics of a Compression Ignition Engine Operating on Blends of Castor Oil Biodiesel-Diesel

NASA Astrophysics Data System (ADS)

Kanwar, Roopesh; Sharma, Pushpendra Kumar; Singh, Aditya Narayan; Agrawal, Yadvendra Kumar

2017-04-01

Diesel vehicles are the nerves and veins of transportation, particularly in developing countries. With the rapid rate of modernization, increasing demand of fuel is inevitable. The exponential increase in fuel prices and the scarcity of its supply from the environment have promoted interest in the development of alternative sources of fuel. In this work, genus Ricinus communis L. was studied in order to delimit their potential as a raw material for biodiesel production. Further, castor oil, ethyl ester were prepared by transesterification using potassium hydroxide (KOH) as a catalyst and tested on a four-stroke, single-cylinder compression ignition engine. The test was carried out at a constant speed of 3000 rpm at different loads. The results represent a substantial decrease in carbon monoxide (CO) emission with an increasing biodiesel percentage. The reduction of CO in B05, B10, B15 and B20 averaged 11.75, 22.02, 24.23 and 28.79 %, respectively, compared to mineral diesel. The emission results of the comparative test indicated that CO, oxygen (O2) and smoke density emissions are found to be lower when the engine is filled with B05, B10, B15 and B20 as compared to mineral diesel, while carbon dioxide (CO2) and nitrogen oxide (NOx) with B05, B10, B15 and B20 are found to increase marginally. Brake thermal efficiency and brake specific fuel consumption decrease and increase respectively in biodiesel with different blends in comparison of mineral diesel.

Evaluation of safety in clinical use of generic paclitaxel [NK] for injection.

PubMed

Tsukiyama, Ikuto; Hotta, Kazuo; Takeuchi, Masayuki; Onishi, Masahumi; Toyama, Yukio; Saito, Hiroko; Sai, Yoshimichi; Miyamoto, Ken-Ichi; Hasegawa, Takaaki

2012-04-01

The introduction of generic drugs is a favored strategy in reducing medical costs, but some clinicians are often reluctant to use them because of lack of information with regard to their side effects. Generic paclitaxel [NK] differs from the proprietary version, Taxol®, in containing added citric acid and a more pure form of castor oil. However, little information exists regarding the effects of these additives on adverse events such as vascular pain, phlebitis, hypersensitivity and hepatic dysfunction. To compensate for this lack of information and to validate the safety of using generic paclitaxel, we investigated adverse events in response to generic paclitaxel [NK]. Our investigation focused on patients treated with both the proprietary formulation (Taxol® for injection) and the generic version(paclitaxel [NK] for injection)sequentially from April 2008 to March 2009. Adverse events were investigated retrospectively. Incidence of vascular pain, phlebitis and hypersensitivity was similar to that with the original product. Although the expression of some liver enzymes was slightly increased and some gastrointestinal events were reduced following generic paclitaxel [NK] treatment there was no statistically significant difference. The profiles of other adverse events were not significantly different. Increased vascular pain and phlebitis, predicted due to low pH conditions caused by citric acid, were not observed. Similarly, the pure castor oil included in generic paclitaxel [NK] did not influence hypersensitivity and hepatic function. We found no significant differences in our study of proprietary and generic paclitaxel [NK]. Thus, clinicians have no reason for prejudice against using generic paclitaxel [NK] on the basis of increased risk of side effects.

Antidiarrheal activities of isovanillin, iso-acetovanillon and Pycnocycla spinosa Decne ex.Boiss extract in mice

PubMed Central

Sadraei, H.; Ghanadian, M.; Asghari, G.; Azali, N.

2014-01-01

Isovanillin and iso-acetovanillon are two phenolic components isolated from a number of plants including Pycnocycla spinosa. P. spinosa extract has antispasmodic and antidiarrheal activities. However, no comparative study has been done on antidiarrheal action of isovanillin and iso- acetovanillon, so far. The aim of this study was to investigate antidiarrheal action of isovanillin and iso-acetovanillon and their effects on small intestinal transit, for comparison with propantheline. Male mice (25-30 g), fasted over night with free access to water, were treated with test compounds or control (p.o.). Thirty min later castor oil (0.5 ml) was given orally to the animals. In another groups of animals MgSO4 (0.5 ml of 10% solution) was given first and half an hour later the test drugs were administered. Onset and number of wet defecations were recorded for each animal over 3.5 h after treatment with diarrhoea inducing agents. In another groups, intestinal transit of charcoal meal was determined following administration of the compounds. Isovanillin (2 mg/kg & 5 mg/kg), iso-acetovanillon (2 mg/kg & 5 mg/kg) and P. spinosa extract (5 mg/kg) delayed onset of diarrhoea and significantly reduced wet defecation induced by castor oil and MgSO4. They all had antidiarrheal effect similar to propantheline (5 mg/kg). Isovanillin, iso-acetovanillon and P. spinosa extract compared to control groups, significantly reduced small intestinal transit of charcoal meal. This study shows that antidiarrheal effect of P. spinosa extract is at least partially due to presence of two active compounds isovanillin and iso-acetovanillon. PMID:25657776

Antidiarrheal activities of isovanillin, iso-acetovanillon and Pycnocycla spinosa Decne ex.Boiss extract in mice.

PubMed

Sadraei, H; Ghanadian, M; Asghari, G; Azali, N

2014-01-01

Isovanillin and iso-acetovanillon are two phenolic components isolated from a number of plants including Pycnocycla spinosa. P. spinosa extract has antispasmodic and antidiarrheal activities. However, no comparative study has been done on antidiarrheal action of isovanillin and iso- acetovanillon, so far. The aim of this study was to investigate antidiarrheal action of isovanillin and iso-acetovanillon and their effects on small intestinal transit, for comparison with propantheline. Male mice (25-30 g), fasted over night with free access to water, were treated with test compounds or control (p.o.). Thirty min later castor oil (0.5 ml) was given orally to the animals. In another groups of animals MgSO4 (0.5 ml of 10% solution) was given first and half an hour later the test drugs were administered. Onset and number of wet defecations were recorded for each animal over 3.5 h after treatment with diarrhoea inducing agents. In another groups, intestinal transit of charcoal meal was determined following administration of the compounds. Isovanillin (2 mg/kg & 5 mg/kg), iso-acetovanillon (2 mg/kg & 5 mg/kg) and P. spinosa extract (5 mg/kg) delayed onset of diarrhoea and significantly reduced wet defecation induced by castor oil and MgSO4. They all had antidiarrheal effect similar to propantheline (5 mg/kg). Isovanillin, iso-acetovanillon and P. spinosa extract compared to control groups, significantly reduced small intestinal transit of charcoal meal. This study shows that antidiarrheal effect of P. spinosa extract is at least partially due to presence of two active compounds isovanillin and iso-acetovanillon.

The application of 1,8-cineole, a terpenoid oxide present in medicinal plants, inhibits castor oil-induced diarrhea in rats.

PubMed

Jalilzadeh-Amin, Ghader; Maham, Massoud

2015-04-01

1,8-Cineole, a terpene, characterized as a major constituent occurring in the essential oils of several aromatic plants. It is widely used in pharmaceutical industry, as a food additive and for culinary purposes. This study investigates the inhibitory effect of 1,8-cineole on transit time and diarrhea in animal models. Acute toxicity and lethality of 1-8-cineole was determined by Lork's guidelines. The antidiarrheal effect of 1,8-cineole was investigated by determining the intestinal transit and enterpooling in rats. In all experiments, different doses of 1,8-cineole (20-120 mg/kg), atropine, and loperamide were administered orally. The LD50 of 1,8-cineole for oral administration was estimated to be 1280 mg/kg. 1,8-Cineole (20-120 mg/kg) did not show a significant decrease in small intestine transit (p > 0.05); however, the highest dose displayed a significant decrease in comparison with atropine (p < 0.05). This substance decreased the peristaltic index value to 68 ± 0.36% at a dose of 120 mg/kg compared with the control group (85.22 ± 4.31%) in the castor oil transit test. 1,8-Cineole significantly delayed the onset of diarrhea to -142.33 ± 6.08 min at 120 mg/kg, while the time was 103.66 ± 20.73 min for the control and >240 min for the loperamide. Moreover, 1,8-cineole significantly decreased intestinal fluid accumulation (p < 0.05). This study demonstrated antispasmodic and antisecretory activities of 1,8-cineole and rationalized the traditional use of the plant containing various levels of this terpene in the treatment of gastrointestinal complains such as diarrhea.

Development and characterization of controlled release polar lipid microparticles of candesartan cilexetil by solid dispersion

PubMed Central

Kamalakkannan, V; Puratchikody, A; Ramanathan, L

2013-01-01

Candesartan cilexetil (CC) is a newer class of angiotensin II receptor antagonist used for the treatment of hypertension. The solubility of the CC is very poor and its oral bioavailability is only 15%. The controlledrelease polar lipid microparticles of CC (formulations F1, F2, F3 and F4) were prepared using variable erodible lipophilic excipients like hydrogenated castor oil, stearic acid, cetostearyl alcohol and carnauba wax by fusion method. The particle sizes of polar lipid microparticles were less than 50 microns and they were irregular in shape. Drug content ranged between 98.96 ± 2.1 and 101.9 ± 1.6% were present in all the formulations. The formulation F3 showed better drug release throughout the study period in a controlled release manner. Moreover, the in vitro release showed that all the formulations were best fitted to Higuchi model. Accelerated stability studies indicated that there was no significant changes in the chemical and physical characteristics of the formulated drug product during initial and at the end of the study period. The FTIR and DSC studies showed that there was no interaction between the drug and lipophilic excipients and no polymorphic transitions in all formulations. The X-ray diffraction peak of solid dispersion indicated that the crystalline nature of CC disappeared and no new peaks could be observed, suggesting the absence of interaction between drug and excipients. PMID:24019822

Enhancement of antibacterial activity of tilmicosin against Staphylococcus aureus by solid lipid nanoparticles in vitro and in vivo.

PubMed

Wang, X F; Zhang, S L; Zhu, L Y; Xie, S Y; Dong, Z; Wang, Y; Zhou, W Z

2012-01-01

This study aimed to enhance the antibacterial activity of tilmicosin by solid lipid nanoparticles (SLN). Tilmicosin-loaded hydrogenated castor oil (HCO)-SLN was prepared using a hot homogenisation and ultrasonication method. The physicochemical characteristics of SLN were investigated by scanning electron microscopy (SEM) and photon correlation spectroscopy (PCS). The antibacterial activity of tilmicosin-SLN against Staphylococcus aureus was evaluated by growth inhibition and colony-counting method. A therapeutic study of tilmicosin-SLN was conducted by subcutaneous injection in a mouse mastitis model infected with S. aureus by teat canal infusion. Therapeutic efficacy was assessed by physical appearance of the mammary gland and measurement of colony-forming units (CFU) per gland. The results showed that the diameter, polydispersivity index, zeta potential, encapsulation efficiency and loading capacity of the nanoparticles were 343±26 nm, 0.33±0.08, -7.9±0.4 mV, 60.4±3.3% and 11.2±0.47%, respectively. Tilmicosin-SLN showed a sustained-release effect and sustained and enhanced antibacterial activity in vitro. SLN significantly enhanced the therapeutic efficacy of tilmicosin determined by lower CFU counts and a decreased degree of inflammation. These results demonstrated that the HCO-SLN is an effective carrier to enhance the antibacterial activity of tilmicosin. Copyright © 2010. Published by Elsevier Ltd.

The use of D-optimal mixture design in optimising okara soap formulation for stratum corneum application.

PubMed

Borhan, Farrah Payyadhah; Abd Gani, Siti Salwa; Shamsuddin, Rosnah

2014-01-01

Okara, soybean waste from tofu and soymilk production, was utilised as a natural antioxidant in soap formulation for stratum corneum application. D-optimal mixture design was employed to investigate the influence of the main compositions of okara soap containing different fatty acid and oils (virgin coconut oil A (24-28% w/w), olive oil B (15-20% w/w), palm oil C (6-10% w/w), castor oil D (15-20% w/w), cocoa butter E (6-10% w/w), and okara F (2-7% w/w)) by saponification process on the response hardness of the soap. The experimental data were utilized to carry out analysis of variance (ANOVA) and to develop a polynomial regression model for okara soap hardness in terms of the six design factors considered in this study. Results revealed that the best mixture was the formulation that included 26.537% A, 19.999% B, 9.998% C, 16.241% D, 7.633% E, and 7.000% F. The results proved that the difference in the level of fatty acid and oils in the formulation significantly affects the hardness of soap. Depending on the desirable level of those six variables, creation of okara based soap with desirable properties better than those of commercial ones is possible.

76 FR 57103 - Office of Commercial Space Transportation (AST); Notice of Availability of the Supplemental...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-15

..., consisting of a two-stage Castor 120 solid-propellant rocket motor with the addition of up to six Castor IVA or Castor IVXL rocket motors strapped to the first stage. The 1995 EA analyzed the potential...

Inhibition of Acetoclastic Methanogenesis in Crude Oil- and Creosote-Contaminated Groundwater

USGS Publications Warehouse

Warren, E.; Bekins, B.A.; Godsy, E.M.; Smith, V.K.

2003-01-01

The inhibition of acetoclastic methanogenesis in crude oil- and creosote-contaminated groundwater was studied. The crude oil and water-soluble components of creosote contributed to the inhibition of acetoclastic methanogens. Acetoclastic methanogenesis was much more susceptible to the toxic inhibition of crude oil and creosote than either hydrogen- or formate-utilizing methanogenesis. The effect of this toxic inhibition was apparent in the population of the methanogenic trophic groups near nonaqueous crude oil at the Bemidji, MN, site. At a crude oil-contaminated site, numbers of acetoclastic methanogens found close to crude oil were 100 times fewer than those of hydrogen- and formate-utilizing methanogens. In laboratory toxicity assays, crude oil collected from the site inhibited methane production from acetate but not from formate or hydrogen. Toxicity assays with aqueous creosote extract completely inhibited acetate utilization over the range of tested dilutions but only mildly affected formate and hydrogen utilization. Wastewater reactor studies indicated that this toxicity would result in a decrease in the biodegradation rate of contaminants at sites where toxic compounds are present.

The preparation of 3,5-dihydroxy-4-isopropylstilbene nanoemulsion and in vitro release

PubMed Central

Zhang, Yue; Gao, Jungang; Zheng, Hetang; Zhang, Ran; Han, Yucui

2011-01-01

We have reported a novel procedure to prepare 3,5-dihydroxy-4-isopropylstilbene (DHPS) nanoemulsion, using a low-energy emulsification method. Based on the phase diagram, the optimum prescription of nanoemulsion preparation was screened. With polyoxyethylenated castor oil (EL-40) as the surfactant, ethanol as the co-surfactant, and isopropyl myristate (IPM) as the oil phase, the DHPS nanoemulsion was obtained with a transparent appearance, little viscosity, and spherically uniform distribution verified by transmission electron microscopy and laser scattering analyzer. The nanoemulsion was also determined by FT-Raman spectroscopy. The DHPS nanoemulsion demonstrated good stability and stable physical and chemical properties. The nanoemulsion dramatically improved the transdermal release of DHPS (from 8.02 μg · cm−2 to 273.15 μg · cm−2) and could become a favorable new dosage form for DHPS. PMID:21674020

Analytical Method to Estimate the Complex Permittivity of Oil Samples.

PubMed

Su, Lijuan; Mata-Contreras, Javier; Vélez, Paris; Fernández-Prieto, Armando; Martín, Ferran

2018-03-26

In this paper, an analytical method to estimate the complex dielectric constant of liquids is presented. The method is based on the measurement of the transmission coefficient in an embedded microstrip line loaded with a complementary split ring resonator (CSRR), which is etched in the ground plane. From this response, the dielectric constant and loss tangent of the liquid under test (LUT) can be extracted, provided that the CSRR is surrounded by such LUT, and the liquid level extends beyond the region where the electromagnetic fields generated by the CSRR are present. For that purpose, a liquid container acting as a pool is added to the structure. The main advantage of this method, which is validated from the measurement of the complex dielectric constant of olive and castor oil, is that reference samples for calibration are not required.

Production of hydrogen from biomass by catalytic steam reforming of fast pyrolysis oil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Czernik, S.; Wang, D.; Chornet, E.

1998-08-01

Hydrogen is the prototype of the environmentally cleanest fuel of interest for power generation using fuel cells and for transportation. The thermochemical conversion of biomass to hydrogen can be carried out through two distinct strategies: (a) gasification followed by water-gas shift conversion, and (b) catalytic steam reforming of specific fractions derived from fast pyrolysis and aqueous/steam processes of biomass. This paper presents the latter route that begins with fast pyrolysis of biomass to produce bio-oil. This oil (as a whole or its selected fractions) can be converted to hydrogen via catalytic steam reforming followed by a water-gas shift conversion step.more » Such a process has been demonstrated at the bench scale using model compounds, poplar oil aqueous fraction, and the whole pyrolysis oil with commercial Ni-based steam reforming catalysts. Hydrogen yields as high as 85% have been obtained. Catalyst initial activity can be recovered through regeneration cycles by steam or CO{sub 2} gasification of carbonaceous deposits.« less

A machine learning approach for viral genome classification.

PubMed

Remita, Mohamed Amine; Halioui, Ahmed; Malick Diouara, Abou Abdallah; Daigle, Bruno; Kiani, Golrokh; Diallo, Abdoulaye Baniré

2017-04-11

Advances in cloning and sequencing technology are yielding a massive number of viral genomes. The classification and annotation of these genomes constitute important assets in the discovery of genomic variability, taxonomic characteristics and disease mechanisms. Existing classification methods are often designed for specific well-studied family of viruses. Thus, the viral comparative genomic studies could benefit from more generic, fast and accurate tools for classifying and typing newly sequenced strains of diverse virus families. Here, we introduce a virus classification platform, CASTOR, based on machine learning methods. CASTOR is inspired by a well-known technique in molecular biology: restriction fragment length polymorphism (RFLP). It simulates, in silico, the restriction digestion of genomic material by different enzymes into fragments. It uses two metrics to construct feature vectors for machine learning algorithms in the classification step. We benchmark CASTOR for the classification of distinct datasets of human papillomaviruses (HPV), hepatitis B viruses (HBV) and human immunodeficiency viruses type 1 (HIV-1). Results reveal true positive rates of 99%, 99% and 98% for HPV Alpha species, HBV genotyping and HIV-1 M subtyping, respectively. Furthermore, CASTOR shows a competitive performance compared to well-known HIV-1 specific classifiers (REGA and COMET) on whole genomes and pol fragments. The performance of CASTOR, its genericity and robustness could permit to perform novel and accurate large scale virus studies. The CASTOR web platform provides an open access, collaborative and reproducible machine learning classifiers. CASTOR can be accessed at http://castor.bioinfo.uqam.ca .

An oleate 12-hydroxylase from Ricinus communis L. is a fatty acyl desaturase homolog

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van De Loo, F.J.; Broun, P.; Turner, S.

1995-07-18

Recent spectroscopic evidence implicating a binuclear iron site at the reaction center of fatty acyl desaturases suggested to us that certain fatty acyl hydroxylases may share significant amino acid sequence similarity with desaturases. To test this theory, we prepared a cDNA library from developing endosperm of the castor-oil plant (Ricinus communis L.) and obtained partial nucleotide sequences for 468 anonymous clones that were not expressed at high levels in leaves, a tissue deficient in 12-hydroxyoleic acid. This resulted in the identification of several cDNA clones encoding a polypeptide of 387 amino acids with a predicted molecular weight of 44,407 andmore » with {approx}67% sequence homology to microsomal oleate desaturase from Arabidopsis. Expression of a full-length clone under control of the cauliflower mosaic virus 35S promoter in transgenic tobacco resulted in the accumulation of low levels of 12-hydroxyoleic acid in seeds, indicating that the clone encodes the castor oleate hydroxylase. These results suggest that fatty acyl desaturases and hydroxylases share similar reaction mechanisms and provide an example of enzyme evolution. 26 refs., 6 figs., 1 tab.« less

THE CONVERSION OF FAT TO CARBOHYDRATE IN THE GERMINATING CASTOR BEAN

PubMed Central

Murlin, John R.

1933-01-01

1. Respiration studies on single castor beans, made by means of the Brodie-Warburg method, at various times after the start of germination, as well as studies on groups of germinating beans over periods of 3 to 8 days, made by a simple procedure involving analysis of the respired air by the Haldane method, consistently give respiratory quotients from 0.30 to 0.58, indicating the conversion of the oil to carbohydrate. 2. The R.Q. varies with the stage of germination, the lowest point occurring when the new growth (hypocotyl) measures from 20 to 35 mm. in length. 3. The R.Q. of the young plant (cotyledons and hypocotyl), separated from the endosperm and studied in the same apparatus, varies from 0.78 to 1.00. It is invariably high enough to indicate considerable combustion of sugar. The R.Q. of the endosperm alone is low, but usually somewhat higher than that of the entire germinating structure. 4. On the same unit of moist weight the young plant (cotyledons and hypocotyl) produces about 2.6 times as much CO2 as the endosperm, whereas it absorbs only 1.3 times as much O2. PMID:19872779

Risk of ricin from commercial castor production in North America

USDA-ARS?s Scientific Manuscript database

Commercial production of castor, as a source of highly valuable hydroxyl fatty acids, has been limited by both the real and perceived risks of commercial castor production in North America. Crop commodity groups, regulatory governmental agencies, and much of the general public may have reservations ...

Coal liquefaction process

DOEpatents

Karr, Jr., Clarence

1977-04-19

An improved coal liquefaction process is provided which enables conversion of a coal-oil slurry to a synthetic crude refinable to produce larger yields of gasoline and diesel oil. The process is characterized by a two-step operation applied to the slurry prior to catalytic desulfurization and hydrogenation in which the slurry undergoes partial hydrogenation to crack and hydrogenate asphaltenes and the partially hydrogenated slurry is filtered to remove minerals prior to subsequent catalytic hydrogenation.

Co-processing of carbonaceous solids and petroleum oil

DOEpatents

Gupta, Avinash; Greene, Marvin I.

1992-01-01

In a process for producing distillates from coal by a first stage thermal liquefaction followed by a catalytic hydrogenation, liquefaction solvent is added at points spaced over the length of the thermal liquefaction heater. Coal may be co-processed with petroleum oil by adding pre-hydrogenated oil to the first stage or unhydrogenated oil to the second stage.

Assessment of antidiarrhoeal activity of the methanol extract of Xylocarpus granatum bark in mice model.

PubMed

Rouf, Razina; Uddin, Shaikh Jamal; Shilpi, Jamil Ahmad; Alamgir, Mahiuddin

2007-02-12

The methanol extract of Xylocarpus granatum bark was studied for its antidiarrhoeal properties in experimental diarrhoea, induced by castor oil and magnesium sulphate in mice. At the doses of 250 and 500 mg/kg per oral, the methanol extract showed significant and dose-dependent antidiarrhoeal activity in both models. The extracts also significantly reduced the intestinal transit in charcoal meal test when compared to atropine sulphate (5 mg/kg; i.m.). The results showed that the extracts of Xylocarpus granatum bark have a significant antidiarrhoeal activity and supports its traditional uses in herbal medicine.

Pyrolysis of de-oiled seed cake of Jatropha Curcas and catalytic steam reforming of pyrolytic bio-oil to hydrogen.

PubMed

Renny, Andrew; Santhosh, Viswanathan; Somkuwar, Nitin; Gokak, D T; Sharma, Pankaj; Bhargava, Sanjay

2016-11-01

The aim of this work was to study the pyrolysis of de-oiled seed cake of Jatropha Curcas and catalytic steam reforming of pyrolytic bio-oil to hydrogen. As per literature, presence of heavy nitrogenous and oxygenated compounds leads to catalyst deactivation. Here, an attempt has been made to tune pyrolytic reactions to optimize the N and O content of the pyrolytic bio-oil. Bio-oil conversion and hydrogen yield decreased as reaction progressed, which attributes to temporary loss of catalytic activity by blockage of catalyst pores by carbon deposition. Further, retention of steam reforming activity after repetitive steam activation suggests long-term catalyst usage. Copyright © 2016 Elsevier Ltd. All rights reserved.

Organic acids, amino acids compositions in the root exudates and Cu-accumulation in castor (Ricinus communis L.) Under Cu stress.

PubMed

Huang, Guoyong; Guo, Guangguang; Yao, Shiyuan; Zhang, Na; Hu, Hongqing

2016-01-01

Ricinus communis L. is a hyperaccumulation plant newly discovered in an abandoned land of Cu mine in China. A hydroponic experiment was then carried out to determine the root exudates in the Cu-tolerant castor (Ricinus communis L.). Plants were grown in nutrient solution with increasing level of Cu doses (0, 100, 250, 500, and 750 μmol/L Cu) in the form of CuSO4. Cu accumulation in the roots and shoots of castor, and root exudates collected from the castor were measured. The results indicated that the castor had a high Cu accumulation capacity and the Cu concentrations in the shoots and roots of the castor treated with 750 μmol/L Cu were 177.1, 14586.7 mg/kg, respectively. Tartaric was the largest in the root exudates in terms of concentrations, which reached up to 329.13 μmol/g (dry plant) in the level of 750 μmol/L Cu. There was a significantly positive linear relationship between the Cu concentration in root and the concentration of succinic (R = 0.92, P < 0.05), tartaric (R = 0.96, P < 0.01), and citric (R = 0.89, P < 0.05). These results indicated that the difference in root exudation from castor could affect their Cu tolerance. What is more, significant is that the high tartaric and citric, the low oxalic and cysteine in the root exudation of castor contributed to toleration of high Cu concentrations.

Improved method for extraction of castor seed for toxin determination

USDA-ARS?s Scientific Manuscript database

The effort to identify castor seeds with low ricin content is considered to be a key to increasing cultivation of the castor plant for industrial applications. The procedure used to obtain soluble protein from the seed is a limiting factor for screening large numbers of seeds. Usually, the seed is...

Naturally occurring and experimentally induced castor bean (Ricinus communis) poisoning in ducks

USGS Publications Warehouse

Jensen, Wayne I.; Allen, J.P.

1981-01-01

Castor bean (Ricinus communis) poisoning accounted for the death of several thousand ducks in the Texas panhandle in the fall and winter months of 1969-1971.Signs of intoxication resembled those of botulism, except for mucoid, blood-tinged excreta. The most common lesions were severe fatty change in the liver, widely distributed internal petechial hemorrhages or ecchymoses, and catarrhal enteritis.Nearly intact castor beans were found in the stomach of one duck during field necropsy. Fragments of seed coat resembling castor bean were found in the stomachs of 10 of 14 ducks examined in the laboratory.Clinical signs and postmortem lesions observed in wild ducks were induced experimentally in mallards (Anas platyrhynchos) by force-feeding intact castor beans. Toxicity titrations were erratic, but the LD50 appeared to be between three and four seeds.The mouse toxicity test, used to detect Clostridium botulinum toxin in the blood serum of intoxicated ducks, was negative in every case. Hemagglutination and precipitin tests generally failed to detect castor bean in extracts of excreta or intestinal contents of experimentally intoxicated ducks.

Effect of Hydrogenated, Liquid and Ghee Oils on Serum Lipids Profile

PubMed Central

Mohammadifard, Noushin; Nazem, Masoud; Naderi, Gholam-Ali; Saghafian, Faezeh; Sajjadi, Firoozeh; Maghroon, Maryam; Bahonar, Ahmad; Alikhasi, Hasan; Nouri, Fatemeh

2010-01-01

BACKGROUND Trans fatty acids are known as the most harmful type of dietary fats, so this study was done to compare the effects of hydrogenated, liquid and ghee oils on serum lipids profile of healthy adults. METHODS This study was a randomized clinical trial conducted on 129 healthy participants aged from 20 to 60 years old who were beneficiaries of Imam-e-Zaman charitable organization. Subjects were randomly divided into 3 groups and each group was treated with a diet containing cooking and frying liquid, ghee, or hydrogenated for 40 days. Fasting serum lipids, including total cholesterol (TC), triglyceride (TG), LDL-cholesterol (LDL-C), HDL-cholesterol (HDL-C), apoprotein A (Apo A), and apoprotein B (Apo B) were measured before and after the study. RESULTS TC, TG and Apo B had a significant reduction in the liquid oil group compared to the hydrogenated oil group. In the ghee group TG declined and Apo A increased significantly (P < 0.01). Liquid oil group had a significant reduction in HDL-C, compared to the ghee oil group (P < 0.05). CONCLUSION It was concluded that consuming liquid oil along with frying oil caused to reduce all serum lipid levels. However, ghee oil only reduced TG and increased HDL-C levels. PMID:22577408

Determination of free fatty acids in pharmaceutical lipids by ¹H NMR and comparison with the classical acid value.

PubMed

Skiera, Christina; Steliopoulos, Panagiotis; Kuballa, Thomas; Diehl, Bernd; Holzgrabe, Ulrike

2014-05-01

Indices like acid value, peroxide value, and saponification value play an important role in quality control and identification of lipids. Requirements on these parameters are given by the monographs of the European pharmacopeia. (1)H NMR spectroscopy provides a fast and simple alternative to these classical approaches. In the present work a new (1)H NMR approach to determine the acid value is described. The method was validated using a statistical approach based on a variance components model. The performance under repeatability and in-house reproducibility conditions was assessed. We applied this (1)H NMR assay to a wide range of different fatty oils. A total of 305 oil and fat samples were examined by both the classical and the NMR method. Except for hard fat, the data obtained by the two methods were in good agreement. The (1)H NMR method was adapted to analyse waxes and oleyloleat. Furthermore, the effect of solvent and in the case of castor oil the effect of the oil matrix on line broadening and chemical shift of the carboxyl group signal are discussed. Copyright © 2013 Elsevier B.V. All rights reserved.

Ultrastructural changes in the ovary cells of engorged Rhipicephalus sanguineus female ticks treated with esters of ricinoleic acid from castor oil (Ricinus communis).

PubMed

Sampieri, Bruno Rodrigues; Arnosti, André; Nunes, Pablo Henrique; Furquim, Karim Christina Scopinho; Chierice, Gilberto Orivaldo; Mathias, Maria Izabel Camargo

2012-05-01

Rhipicephalus sanguineus is a widely distributed tick species that has adapted to the urban environment, and the dog is its main host. This species is also known as a vector and reservoir of diseases caused by bacteria, protozoa, and viruses. Currently, acaricides of synthetic chemical origin have been widely and indiscriminately used, leading to the development of resistance to these products by ticks and causing damage to the environment. Thus, these issues have made it necessary to seek other forms of controlling these ectoparasites. R. sanguineus was artificially infested in host New Zealand White rabbits, which were divided into four treatment groups: control (CG1 and CG2) and treatment (TG1 and TG2) groups. TG1 and TG2 hosts were provided with feed supplemented with esters of ricinoleic acid from castor oil at a concentration of 5 g/kg of feed for 7 and 15 days. Afterward, the ovaries of the female ticks were removed for analysis by transmission electron microscopy. The results showed ultrastructural changes in the somatic and germ cells of ovaries from TG1 and TG2 females, particularly with respect to chorion deposition, a protective membrane of the oocyte, as well as in the transport process of vitellogenic materials via the hemolymph and pedicel cells. Moreover, the mitochondria were less electron-dense and had cristae that were more disorganized than the mitochondria from CG1 and CG2 individuals. Thus, this study demonstrated the action of esters on the ovaries of R. sanguineus, signaling the prospect of a way to control this ectoparasite without affecting nontarget organisms or the environment. Copyright © 2011 Wiley Periodicals, Inc.

Evaluation of the anti-diarrheal activity of the hydromethanolic root extract of Rhus tripartita (Ucria) (Anacardiacae).

PubMed

Ben Barka, Zaineb; Aouadhi, Chedia; Tlili, Mounira; Alimi, Hichem; Ben Miled, Hanene; Ben Rhouma, Khémais; Sakly, Mohsen; Ksouri, Riadh; Schneider, Yves Jacques; Maaroufi, Abderrazek; Tebourbi, Olfa

2016-10-01

Rhus tripartita (Anacardiacae) is a plant which is traditionally used for the treatment of ulcer and diarrhea in Tunisia. However, the scientific basis for this usage has not been well established. The core aim of the present study is to evaluate the antidiarrheal activity of Rhus tripartita root methanolic extract (RRE). The antidiarrheal activity of RRE oral doses (50, 100, 200 and 300mg/kg) was evaluated using the castor oil-induced diarrhea, the intestinal fluid emptying method and the normal intestinal transit test. The antibacterial activity was tested against four pathogenic bacteria using two methods. The RRE was also phytochemical studied. Diarrhea experiments showed a protective effect of the RRE which produced a significant (p<0.05) and dose-dependent reduction of all the diarrhea parameters. It delayed the onset of diarrhea, produced a significant decrease in the frequency of defecation and the diarrhea score severity and decreased the volume of intestinal fluid induced by castor oil as well as the propulsion intestinal transit. The effect of the extract at the highest dose (300mg/kg) was similar to that of loperamide, the standard anti-diarrheal drug (10mg/kg). The anti-bacterial activity test showed that RRE exhibited a great inhibition activity against four pathogenic bacteria strains (Esherichia coli, Salmonella typhimurium, Salmonella argenosa, Staphylococcus aureus). Oral administration of the extract up to 3g/kg did not produce any acute toxicity in rats. The preliminary phytochemical screening of the RRE revealed the presence of flavonoids, tannins, and polyphenols. Results showed that RRE at 300mg/kg possesses the highest anti-diarrheal activity possibly mediated by the inhibitory effects on gastrointestinal propulsion and intestinal fluid accumulation. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

Diametral tensile strength and film thickness of an experimental dental luting agent derived from castor oil.

PubMed

Carmello, Juliana Cabrini; Fais, Laiza Maria Grassi; Ribeiro, Lígia Nunes de Moraes; Claro Neto, Salvador; Guaglianoni, Dalton Geraldo; Pinelli, Lígia Antunes Pereira

2012-02-01

The need to develop new dental luting agents in order to improve the success of treatments has greatly motivated research. The aim of this study was to evaluate the diametral tensile strength (DTS) and film thickness (FT) of an experimental dental luting agent derived from castor oil (COP) with or without addition of different quantities of filler (calcium carbonate - CaCO3). Eighty specimens were manufactured (DTS N=40; FT N=40) and divided into 4 groups: Pure COP; COP 10%; COP 50% and zinc phosphate (control). The cements were mixed according to the manufacturers' recommendations and submitted to the tests. The DTS test was performed in the MTS 810 testing machine (10 KN, 0.5 mm/min). For FT test, the cements were sandwiched between two glass plates (2 cm²) and a load of 15 kg was applied vertically on the top of the specimen for 10 min. The data were analyzed by means of one-way ANOVA and Tukey's test (α=0.05). The values of DTS (MPa) were: Pure COP- 10.94 ± 1.30; COP 10%- 30.06 ± 0.64; COP 50%- 29.87 ± 0.27; zinc phosphate- 4.88 ± 0.96. The values of FT (µm) were: Pure COP- 31.09 ± 3.16; COP 10%- 17.05 ± 4.83; COP 50%- 13.03 ± 4.83; Zinc Phosphate- 20.00 ± 0.12. One-way ANOVA showed statistically significant differences among the groups (DTS - p=1.01E-40; FT - p=2.4E-10). The experimental dental luting agent with 50% of filler showed the best diametral tensile strength and film thickness.

Diametral tensile strength and film thickness of an experimental dental luting agent derived from castor oil

PubMed Central

CARMELLO, Juliana Cabrini; FAIS, Laiza Maria Grassi; RIBEIRO, Lígia Nunes de Moraes; CLARO NETO, Salvador; GUAGLIANONI, Dalton Geraldo; PINELLI, Lígia Antunes Pereira

2012-01-01

The need to develop new dental luting agents in order to improve the success of treatments has greatly motivated research. Objective The aim of this study was to evaluate the diametral tensile strength (DTS) and film thickness (FT) of an experimental dental luting agent derived from castor oil (COP) with or without addition of different quantities of filler (calcium carbonate - CaCO3). Material and Methods Eighty specimens were manufactured (DTS N=40; FT N=40) and divided into 4 groups: Pure COP; COP 10%; COP 50% and zinc phosphate (control). The cements were mixed according to the manufacturers' recommendations and submitted to the tests. The DTS test was performed in the MTS 810 testing machine (10 KN, 0.5 mm/min). For FT test, the cements were sandwiched between two glass plates (2 cm2) and a load of 15 kg was applied vertically on the top of the specimen for 10 min. The data were analyzed by means of one-way ANOVA and Tukey's test (α=0.05). Results The values of DTS (MPa) were: Pure COP- 10.94±1.30; COP 10%- 30.06±0.64; COP 50%- 29.87±0.27; zinc phosphate- 4.88±0.96. The values of FT (µm) were: Pure COP- 31.09±3.16; COP 10%- 17.05±4.83; COP 50%- 13.03±4.83; Zinc Phosphate- 20.00±0.12. One-way ANOVA showed statistically significant differences among the groups (DTS - p=1.01E-40; FT - p=2.4E-10). Conclusion The experimental dental luting agent with 50% of filler showed the best diametral tensile strength and film thickness. PMID:22437672

Comparative effects of Bisphenol S and Bisphenol A on the development of female reproductive system in rats; a neonatal exposure study.

PubMed

Ahsan, Nida; Ullah, Hizb; Ullah, Waheed; Jahan, Sarwat

2018-04-01

Bisphenol A (BPA) has been well documented for its endocrine disrupting potential however, very little is known about endocrine disrupting abilities of bisphenol S (BPS). The present study aimed to compare the endocrine disrupting potentials of BPS with BPA, using female rats as an experimental animal model. On postnatal day 1 (PND 1) female pups born were randomly assigned to seven different treatments. Control group received subcutaneous injection of castor oil (50 μL) from PND 1 to PND 10. Three groups of female pups were injected subcutaneously with different concentrations (0.5, 5 and 50 mg/kg in 50 μL castor oil) of BPS, while remaining three groups were treated with 0.5, 5 and 50 mg/kg BPA. Highest doses treatments of both compounds resulted in delayed puberty onset and altered estrous cyclicity. Final body weight was significantly high in the highest dose treated groups of both BPS and BPA. Gonadosomatic index, absolute and relative weight of uteri was significantly reduced in BPS (5 and 50 mg/kg) and BPA (5 and 50 mg/kg) treated groups than control. Plasma concentrations of testosterone and estradiol were significantly increased, while plasma progesterone, Luteinizing hormone (LH) and Follicle stimulating hormone (FSH) concentrations were significantly reduced in highest doses treated groups. Dose dependent increase in the number of cystic follicles in the ovaries was evident along with an increase in the number of atratic follicles. The results suggest that neonatal exposure to higher concentrations of BPS can lead to BPA like structural and endocrine alterations in female rats. Copyright © 2018 Elsevier Ltd. All rights reserved.

Phytoextraction of metals and rhizoremediation of PAHs in co-contaminated soil by co-planting of Sedum alfredii with ryegrass (Lolium perenne) or castor (Ricinus communis).

PubMed

Wang, Kai; Huang, Huagang; Zhu, Zhiqiang; Li, Tingqiang; He, Zhenli; Yang, Xiaoe; Alva, Ashok

2013-01-01

A pot experiment was conducted to investigate the potential for phytoextraction of heavy metals and rhizoremediation of polycyclic aromatic hydrocarbons (PAHs) in co-contaminated soil by co-planting a cadmium/zinc (Cd/Zn) hyperaccumulator and lead (Pb) accumulator Sedum alfredii with ryegrass (Lolium perenne) or castor (Ricinus communis). Co-planting with castor decreased the shoot biomass of S. alfredii as compared to that in monoculture. Cadmium concentration in S. alfredii shoot significantly decreased when grown with ryegrass or castor as compared to that in monoculture. However, no reduction of Zn or Pb concentration in S. alfredii shoot was detected in co-planting treatments. Total removal of either Cd, Zn, or Pb by plants was similar across S. alfredii monoculture or co-planting with ryegrass or castor, except enhanced Pb removal in S. alfredii and ryegrass co-planting treatment. Co-planting of S. alfredii with ryegrass or castor significantly enhanced the pyrene and anthracene dissipation as compared to that in the bare soil or S. alfredii monoculture. This appears to be due to the increased soil microbial population and activities in both co-planting treatments. Co-planting of S. alfredii with ryegrass or castor provides a promising strategy to mitigate both metal and PAH contaminants from co-contaminated soils.

An investigation into electromagnetic force models: differences in global and local effects demonstrated by selected problems

NASA Astrophysics Data System (ADS)

Reich, Felix A.; Rickert, Wilhelm; Müller, Wolfgang H.

2018-03-01

This study investigates the implications of various electromagnetic force models in macroscopic situations. There is an ongoing academic discussion which model is "correct," i.e., generally applicable. Often, gedankenexperiments with light waves or photons are used in order to motivate certain models. In this work, three problems with bodies at the macroscopic scale are used for computing theoretical model-dependent predictions. Two aspects are considered, total forces between bodies and local deformations. By comparing with experimental data, insight is gained regarding the applicability of the models. First, the total force between two cylindrical magnets is computed. Then a spherical magnetostriction problem is considered to show different deformation predictions. As a third example focusing on local deformations, a droplet of silicone oil in castor oil is considered, placed in a homogeneous electric field. By using experimental data, some conclusions are drawn and further work is motivated.

Fast-responding bio-based shape memory thermoplastic polyurethanes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Petrovic, Zoran S.; Milic, Jelena; Zhang, Fan

Fast response shape-memory polyurethanes were prepared from bio-based polyols, diphenyl methane diisocyanate and butane diol. The bio-based polyester polyols were synthesized from 9-hydroxynonanoic acid, a product obtained by ozonolysis of fatty acids extracted from soy oil and castor oil. The morphology of polyurethanes was investigated by synchrotron ultra-small angle X-ray scattering, which revealed the inter-domain spacing between the hard and soft phases, the degree of phase separation, and the level of intermixing between the hard and soft phases. We also conducted thorough investigations of the thermal, mechanical, and dielectric properties of the polyurethanes, and found that high crystallization rate ofmore » the soft segment gives these polyurethanes unique properties suitable for shapememory applications, such as adjustable transition temperatures, high degree of elastic elongations, and good mechanical strength. In conclusion, these materials are also potentially biodegradable and biocompatible, therefore suitable for biomedical and environmental applications.« less

Estolides Synthesis Catalyzed by Immobilized Lipases

PubMed Central

Aguieiras, Erika C. G.; Veloso, Cláudia O.; Bevilaqua, Juliana V.; Rosas, Danielle O.; da Silva, Mônica A. P.; Langone, Marta A. P.

2011-01-01

Estolides are vegetable-oil-based lubricants obtained from oleic acid or any source of hydroxy fatty acids. In this work, the estolides synthesis from oleic acid and methyl ricinoleate (biodiesel from castor oil), using immobilized commercial lipases (Novozym 435, Lipozyme RM-IM, and Lipozyme TL-IM) in a solvent-free medium was investigated. Acid value was used to monitor the reaction progress by determining the consumption of acid present in the medium. Novozym 435 showed the best performance. Water removal improved the conversion. Novozym 435 was more active at atmospheric pressure. Novozym 435 was reused four times with conversion reaching 15% after the fourth reaction at 80°C. Estolides produced under the reaction conditions used in this work presented good properties, such as, low temperature properties as pour point (−24°C), viscosity (23.9 cSt at 40°C and 5.2 cSt at 100°C), and viscosity index (153). PMID:21755040

Friction and Wear Modifiers Using Solvent Partitioning of Hydrophilic Surface-interactive Chemicals Contained in Boundary Layer-targeted Emulsions

NASA Technical Reports Server (NTRS)

Richmond, Robert Chafee (Inventor); Schramm, Jr., Harry F. (Inventor); Defalco, Francis G. (Inventor)

2013-01-01

A wear and/or friction reducing additive for a lubricating fluid in which the additive is a combination of a moderately hydrophilic single-phase compound and an anti-wear and/or anti-friction aqueous salt solution. The aqueous salt solution produces a coating on boundary layer surfaces. The lubricating fluid can be an emulsion-free hydrophobic oil, hydraulic fluid, antifreeze, or water. Preferably, the moderately hydrophilic single-phase compound is sulfonated castor oil and the aqueous salt solution additionally contains boric acid and zinc oxide. The emulsions produced by the aqueous salt solutions, the moderately hydrophilic single-phase compounds, or the combination thereof provide targeted boundary layer organizers that significantly enhance the anti-wear and/or anti-friction properties of the base lubricant by decreasing wear and/or friction of sliding and/or rolling surfaces at boundary layers.

Fast-responding bio-based shape memory thermoplastic polyurethanes

DOE PAGES

Petrovic, Zoran S.; Milic, Jelena; Zhang, Fan; ...

2017-05-31

Fast response shape-memory polyurethanes were prepared from bio-based polyols, diphenyl methane diisocyanate and butane diol. The bio-based polyester polyols were synthesized from 9-hydroxynonanoic acid, a product obtained by ozonolysis of fatty acids extracted from soy oil and castor oil. The morphology of polyurethanes was investigated by synchrotron ultra-small angle X-ray scattering, which revealed the inter-domain spacing between the hard and soft phases, the degree of phase separation, and the level of intermixing between the hard and soft phases. We also conducted thorough investigations of the thermal, mechanical, and dielectric properties of the polyurethanes, and found that high crystallization rate ofmore » the soft segment gives these polyurethanes unique properties suitable for shapememory applications, such as adjustable transition temperatures, high degree of elastic elongations, and good mechanical strength. In conclusion, these materials are also potentially biodegradable and biocompatible, therefore suitable for biomedical and environmental applications.« less

Fast-Responding Bio-Based Shape Memory Thermoplastic Polyurethanes.

PubMed

Petrović, Zoran S; Milić, Jelena; Zhang, Fan; Ilavsky, Jan

2017-07-14

Novel fast response shape-memory polyurethanes were prepared from bio-based polyols, diphenyl methane diisocyanate and butane diol for the first time. The bio-based polyester polyols were synthesized from 9-hydroxynonanoic acid, a product obtained by ozonolysis of fatty acids extracted from soy oil and castor oil. The morphology of polyurethanes was investigated by synchrotron ultra-small angle X-ray scattering, which revealed the inter-domain spacing between the hard and soft phases, the degree of phase separation, and the level of intermixing between the hard and soft phases. We also conducted thorough investigations of the thermal, mechanical, and dielectric properties of the polyurethanes, and found that high crystallization rate of the soft segment gives these polyurethanes unique properties suitable for shape-memory applications, such as adjustable transition temperatures, high degree of elastic elongations, and good mechanical strength. These materials are also potentially biodegradable and biocompatible, therefore suitable for biomedical and environmental applications.

Friction and Wear Modifiers Using Solvent Partitioning of Hydrophilic Surface-Interactive Chemicals Contained in Boundary Layer-Targeted Emulsions

NASA Technical Reports Server (NTRS)

Defalco, Francis G. (Inventor); Richmond, Robert Chaffee (Inventor); Schramm, Jr., Harry F. (Inventor)

2017-01-01

A wear and/or friction reducing additive for a lubricating fluid in which the additive is a combination of a moderately hydrophilic single-phase compound and an anti-wear and/or anti-friction aqueous salt solution. The aqueous salt solution produces a coating on boundary layer surfaces. The lubricating fluid can be an emulsion-free hydrophobic oil, hydraulic fluid, antifreeze, water, or a water-based lubricant. Preferably, the moderately hydrophilic single-phase compound is sulfonated castor oil and the aqueous salt solution additionally contains boric acid and zinc oxide. The emulsions produced by the aqueous salt solutions, the moderately hydrophilic single-phase compounds, or the combination thereof provide targeted boundary layer organizers that significantly enhance the anti-wear and/or anti-friction properties of the base lubricant by decreasing wear and/or friction of sliding and/or rolling surfaces at boundary layers.

Friction and Wear Modifiers Using Solvent Partitioning of Hydrophilic Surface-Interactive Chemicals Contained in Boundary Layer-Targeted Emulsions

NASA Technical Reports Server (NTRS)

Defalco, Francis G. (Inventor); Richmond, Robert Chaffee (Inventor); Schramm, Harry F., Jr. (Inventor)

2016-01-01

A wear and/or friction reducing additive for a lubricating fluid in which the additive is a combination of a moderately hydrophilic single-phase compound and an anti-wear and/or anti-friction aqueous salt solution. The aqueous salt solution produces a coating on boundary layer surfaces. The lubricating fluid can be an emulsion-free hydrophobic oil, hydraulic fluid, antifreeze, or water. Preferably, the moderately hydrophilic single-phase compound is sulfonated castor oil and the aqueous salt solution additionally contains boric acid and zinc oxide. The emulsions produced by the aqueous salt solutions, the moderately hydrophilic single-phase compounds, or the combination thereof provide targeted boundary layer organizers that significantly enhance the anti-wear and/or anti-friction properties of the base lubricant by decreasing wear and/or friction of sliding and/or rolling surfaces at boundary layers.

Note: Dissolved hydrogen detection in power transformer oil based on chemically etched fiber Bragg grating.

PubMed

Jiang, Jun; Ma, Guo-ming; Song, Hong-tu; Zhou, Hong-yang; Li, Cheng-rong; Luo, Ying-ting; Wang, Hong-bin

2015-10-01

A fiber Bragg grating (FBG) sensor based on chemically etched cladding to detect dissolved hydrogen is proposed and studied in this paper. Low hydrogen concentration tests have been carried out in mixed gases and transformer oil to investigate the repeatability and sensitivity. Moreover, to estimate the influence of etched cladding thickness, a physical model of FBG-based hydrogen sensor is analyzed. Experimental results prove that thin cladding chemically etched by HF acid solution improves the response to hydrogen detection in oil effectively. At last, the sensitivity of FBG sensor chemically etched 16 μm could be as high as 0.060 pm/(μl/l), increased by more than 30% in comparison to un-etched FBG.

Measurement of H2S in Crude Oil and Crude Oil Headspace Using Multidimensional Gas Chromatography, Deans Switching and Sulfur-selective Detection

PubMed Central

Heshka, Nicole E.; Hager, Darcy B.

2015-01-01

A method for the analysis of dissolved hydrogen sulfide in crude oil samples is demonstrated using gas chromatography. In order to effectively eliminate interferences, a two dimensional column configuration is used, with a Deans switch employed to transfer hydrogen sulfide from the first to the second column (heart-cutting). Liquid crude samples are first separated on a dimethylpolysiloxane column, and light gases are heart-cut and further separated on a bonded porous layer open tubular (PLOT) column that is able to separate hydrogen sulfide from other light sulfur species. Hydrogen sulfide is then detected with a sulfur chemiluminescence detector, adding an additional layer of selectivity. Following separation and detection of hydrogen sulfide, the system is backflushed to remove the high-boiling hydrocarbons present in the crude samples and to preserve chromatographic integrity. Dissolved hydrogen sulfide has been quantified in liquid samples from 1.1 to 500 ppm, demonstrating wide applicability to a range of samples. The method has also been successfully applied for the analysis of gas samples from crude oil headspace and process gas bags, with measurement from 0.7 to 9,700 ppm hydrogen sulfide. PMID:26709594

21 CFR 184.1090 - Stearic acid.

Code of Federal Regulations, 2010 CFR

2010-04-01

... vegetable fats and oils and is a principal constituent of most commercially hydrogenated fats. It is... hydrogenated vegetable oil derived from edible sources. (b) The ingredient meets the specifications of the Food...

21 CFR 184.1090 - Stearic acid.

Code of Federal Regulations, 2011 CFR

2011-04-01

... vegetable fats and oils and is a principal constituent of most commercially hydrogenated fats. It is... hydrogenated vegetable oil derived from edible sources. (b) The ingredient meets the specifications of the Food...

Dietary protein deficiency affects n-3 and n-6 polyunsaturated fatty acids hepatic storage and very low density lipoprotein transport in rats on different diets.

PubMed

Bouziane, M; Prost, J; Belleville, J

1994-04-01

Fatty livers and the similarity between the skin lesions in kwashiorkor and those described in experimental essential fatty acid (EFA) deficiency have led to the hypothesis that protein and EFA deficiencies may both occur in chronic malnutrition. The relationship between serum very low density lipoprotein (VLDL) and hepatic lipid composition was studied after 28 d of protein depletion to determine the interactions between dietary protein levels and EFA availability. Rats were fed purified diets containing 20 or 2% casein and 5% fat as either soybean oil rich in EFA, or salmon oil rich in eicosapentaenoic (EPA) and docosahexaenoic (DHA) acids, or hydrogenated coconut oil poor in EFA. Animals were divided into six groups, SOC (20% casein + 5% soybean oil), SOd (2% casein + 5% soybean oil), COC (20% casein + 5% hydrogenated coconut oil), COd (2% casein + 5% hydrogenated coconut oil), SAC (20% casein + 5% salmon oil) and SAd (2% casein + 5% salmon oil). After 28 d, liver steatosis and reduced VLDL-phospholipid contents (P < 0.001) were observed in protein-deficient rats. In protein deficiency, triacylglycerol and phospholipid fatty acid compositions in both liver and VLDL showed a decreased polyunsaturated-to-saturated fatty acid ratio. This ratio was higher with the salmon oil diets and lower with the hydrogenated coconut oil diets. Furthermore, independent of the oil in the diet, protein deficiency decreased linoleic and arachidonic acids in VLDL phospholipids. Conversely, despite decreased proportions of EPA at low protein levels, DHA levels remained higher in rats fed salmon oil diets.(ABSTRACT TRUNCATED AT 250 WORDS)

An ASCA observation of the Castor system

NASA Technical Reports Server (NTRS)

Gotthelf, Eric V.; Jalota, Lalit; Mukai, Koji; White, Nicholas E.

1994-01-01

We report on a day-long ASCA broadband (1-10 keV) spectro-imaging observation of the X-ray emission from the Castor multibinary system. Significant flares were detected from both the flare star system YY Gem (Castor C) and from Castor AB located 73 sec away. Using an optimal viewing geometry and image restoration techniques, we are able to spatially resolve the emission from the two X-ray components. Broadband flare activity from Castor AB is confirmed, and quiescent flux is detected. The quiescent spectrum of YY Gem is a complex blend of emission lines across the ASCA bandpass which requires multitemperature components or two-temperature variable metal-poor abundances (approximately 5-10 below solar) to obtain a satisfactory fit to both the Mewe-Kaastra and Raymond-Smith models. The flare spectrum is consistent with an increase in the emissivity of the hotter component.

The Use of D-Optimal Mixture Design in Optimising Okara Soap Formulation for Stratum Corneum Application

PubMed Central

Borhan, Farrah Payyadhah; Abd Gani, Siti Salwa; Shamsuddin, Rosnah

2014-01-01

Okara, soybean waste from tofu and soymilk production, was utilised as a natural antioxidant in soap formulation for stratum corneum application. D-optimal mixture design was employed to investigate the influence of the main compositions of okara soap containing different fatty acid and oils (virgin coconut oil A (24–28% w/w), olive oil B (15–20% w/w), palm oil C (6–10% w/w), castor oil D (15–20% w/w), cocoa butter E (6–10% w/w), and okara F (2–7% w/w)) by saponification process on the response hardness of the soap. The experimental data were utilized to carry out analysis of variance (ANOVA) and to develop a polynomial regression model for okara soap hardness in terms of the six design factors considered in this study. Results revealed that the best mixture was the formulation that included 26.537% A, 19.999% B, 9.998% C, 16.241% D, 7.633% E, and 7.000% F. The results proved that the difference in the level of fatty acid and oils in the formulation significantly affects the hardness of soap. Depending on the desirable level of those six variables, creation of okara based soap with desirable properties better than those of commercial ones is possible. PMID:25548777

Development of Improved Chemicals and Plastics from Oilseeds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nugent, Patricia A.; Lysenko, Zenon

2006-11-09

The overall objective of this program was to develop technology that can be applied to the production of various chemicals and plastics from seed oils. This research and development program included activities in all four key barrier areas identified in the US DOE Technology Roadmap for Plant/Crop-Based Renewable Resources, namely Plant Science, Production, Processing, and Utilization. Participants in the project included The Dow Chemical Company, Castor Oil, Inc., and the USDA Western Regional Research Center (WRRC). The objective of this production task was to evaluate and develop metathesis catalyst technology as a means of utilizing seed oils as feedstocks formore » the chemical industry. Specifically, ethenolysis of fatty acid methyl esters, FAME’s, leads to functionalized derivatives. These serve as valuable starting points for materials which cascade into a variety of applications, many of which have a current market presence. The relatively recent discovery and commercial availability of a family of metathesis catalysts which are tolerant of polar functional groups and the acquisition and implementation of high throughput synthesis and screening infrastructure led to a prime opportunity to investigate this project area.« less

Effects of sour crude oil on fatigue properties of steel plates for shipbuilding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ouchi, H.; Kobayashi, J.; Ishikawa, T.

1994-12-31

The concentration of diffusible hydrogen introduced into steel was measured, and fatigue crack growth tests and fatigue life tests were carried out in sour crude oil containing a high concentration of hydrogen sulfide and under electrolytic hydrogen-charging conditions in neutral solution, using a high strength steel produced by the thermo-mechanical control process (TMCP) and a mild steel which are steels for hull plates. Comparison of the results demonstrated that a very small amount of hydrogen such as that introduced into steel from sour crude oil under atmospheric pressure accelerated the fatigue crack growth in the high {Delta}K regime and shortenedmore » the fatigue life in the high stress range region, but did not shorten the fatigue life in the low stress region. The electrolytic hydrogen-charging condition appeared to be appropriate as a fatigue-crack-growth test environment to simulate sour crude oil. The deterioration of fatigue characteristics of the TMCP high strength steel was similar with that of the mild steel.« less

Synthesis and analysis of jet fuel from shale oil and coal syncrudes

NASA Technical Reports Server (NTRS)

Gallagher, J. P.; Collins, T. A.; Nelson, T. J.; Pedersen, M. J.; Robison, M. G.; Wisinski, L. J.

1976-01-01

Thirty-two jet fuel samples of varying properties were produced from shale oil and coal syncrudes, and analyzed to assess their suitability for use. TOSCO II shale oil and H-COAL and COED syncrudes were used as starting materials. The processes used were among those commonly in use in petroleum processing-distillation, hydrogenation and catalytic hydrocracking. The processing conditions required to meet two levels of specifications regarding aromatic, hydrogen, sulfur and nitrogen contents at two yield levels were determined and found to be more demanding than normally required in petroleum processing. Analysis of the samples produced indicated that if the more stringent specifications of 13.5% hydrogen (min.) and 0.02% nitrogen (max.) were met, products similar in properties to conventional jet fuels were obtained. In general, shale oil was easier to process (catalyst deactivation was seen when processing coal syncrudes), consumed less hydrogen and yielded superior products. Based on these considerations, shale oil appears to be preferred to coal as a petroleum substitute for jet fuel production.

Formation of free radicals during mechanical degradation of elastomers.

NASA Technical Reports Server (NTRS)

Devries, K. L.; Williams, M. L.; Roylance, D. K.

1971-01-01

Solithane 113 (an amorphous polyurethane elastomer) was prepared by curing equal proportions of castor oil and trifunctional isocyanate for 6 hr 45 min at 170 F. The sample material was mechanically degraded by grinding below and above its glass transition point at liquid nitrogen and room temperatures. The EPR spectra of ground samples were recorded and the number of free radicals were determined by a computer double-integration of the recorded spectra and by a comparison of the values with those of a standard material. Curves of EPR spectra suggest that different molecular mechanisms may be active in degradation of this material below and above its glass transition temperature.

Antidiarrhoeal efficacy of Mangifera indica seed kernel on Swiss albino mice.

PubMed

Rajan, S; Suganya, H; Thirunalasundari, T; Jeeva, S

2012-08-01

To examine the antidiarrhoeal activity of alcoholic and aqueous seed kernel extract of Mangifera indica (M. indica) on castor oil-induced diarrhoeal activity in Swiss albino mice. Mango seed kernels were processed and extracted using alcohol and water. Antidiarrhoeal activity of the extracts were assessed using intestinal motility and faecal score methods. Aqueous and alcoholic extracts of M. indica significantly reduced intestinal motility and faecal score in Swiss albino mice. The present study shows the traditional claim on the use of M. indica seed kernel for treating diarrhoea in Southern parts of India. Copyright © 2012 Hainan Medical College. Published by Elsevier B.V. All rights reserved.

Recovery of different waste vegetable oils for biodiesel production: a pilot experience in Bahia State, Brazil.

PubMed

Torres, Ednildo Andrade; Cerqueira, Gilberto S; Tiago, M Ferrer; Quintella, Cristina M; Raboni, Massimo; Torretta, Vincenzo; Urbini, Giordano

2013-12-01

In Brazil, and mainly in the State of Bahia, crude vegetable oils are widely used in the preparation of food. Street stalls, restaurants and canteens make a great use of palm oil and soybean oil. There is also some use of castor oil, which is widely cultivated in the Sertão Region (within the State of Bahia), and widely applied in industry. This massive use in food preparation leads to a huge amount of waste oil of different types, which needs either to be properly disposed of, or recovered. At the Laboratorio Energia e Gas-LEN (Energy & Gas lab.) of the Universidade Federal da Bahia, a cycle of experiments were carried out to evaluate the recovery of waste oils for biodiesel production. The experiences were carried out on a laboratory scale and, in a semi-industrial pilot plant using waste oils of different qualities. In the transesterification process, applied waste vegetable oils were reacted with methanol with the support of a basic catalyst, such as NaOH or KOH. The conversion rate settled at between 81% and 85% (in weight). The most suitable molar ratio of waste oils to alcohol was 1:6, and the amount of catalyst required was 0.5% (of the weight of the incoming oil), in the case of NaOH, and 1%, in case of KOH. The quality of the biodiesel produced was tested to determine the final product quality. The parameters analyzed were the acid value, kinematic viscosity, monoglycerides, diglycerides, triglycerides, free glycerine, total glycerine, clearness; the conversion yield of the process was also evaluated. Copyright © 2013 Elsevier Ltd. All rights reserved.

Comparison of Pure Palm Olein Oil, Hydrogenated Oil-Containing Palm, and Canola on Serum Lipids and Lipid Oxidation Rate in Rats Fed with these Oils.

PubMed

Amini, Seyed-Asadollah; Ghatreh-Samani, Keihan; Habibi-Kohi, Arash; Jafari, Laleh

2017-02-01

Due to increased consumption of canola oil and hydrogenated oil containing palm and palm olein, and their possible effects on serum lipoproteins, the present study was conducted to determine the effects of these oils on lipids and lipid oxidation level. In this experimental study, 88 Wistar rats were randomly assigned to four groups. Control group (A) was on a normal diet. Groups B, C, and D, in addition to normal diet, were fed with hydrogenated oil-contained palm oil, pure palm olein oil, and canola oil, respectively for 4 weeks. Serum Biochemical factors [total cholesterol (TC), triglyceride (TG), LDL, HDL, LDL/HDL ratio, oxLDL, paraoxanase-1 (PON1), and malondialdehyde (MDA)] were measured. The lowest mean serum TC was seen in the control group and the highest in the group B. There were differences in TC, TG, HDL, MDA, and PON1 between the control group and other groups (P<0.001). The lowest and highest LDL/HDL ratios were observed in the group C and the control group, respectively. Significant differences were seen in OxLDL and PON1 between the control group and other three groups (P<0.05), while there were no significant differences in oxLDL and PON1 among the other three groups (P>0.05). MDA was higher in groups C and D. Canola oil, hydrogenated oil-containing palm and palm olein may increase atherosclerosis risk through decreasing PON1 activity and elevating oxLDL. Palm olein oils in rats' diets cause a considerable decrease in LDL and help to increase HDL.

Tacrolimus is a class II low-solubility high-permeability drug: the effect of P-glycoprotein efflux on regional permeability of tacrolimus in rats.

PubMed

Tamura, Shigeki; Ohike, Atsuo; Ibuki, Rinta; Amidon, Gordon L; Yamashita, Shinji

2002-03-01

The objective of this study is to investigate the role of P-glycoprotein (P-gp), a membrane efflux pump associated with multidrug resistance (MDR) and a known substrate for tacrolimus, in determining the regional intestinal permeability of tacrolimus in rats. Thus, isolated segments of rat jejunum, ileum, or colon were perfused with tacrolimus solutions containing polyethoxylated hydrogenated castor oil 60 surfactant, and with or without verapamil, a P-gp substrate used to reverse the MDR phenotype. The results indicated that the intrinsic permeability of tacrolimus in the jejunum, calculated on the basis of the concentration of non-micellized free tacrolimus, was quite high ( approximately 1.4 x 10(-4) cm/s). The apparent permeability (P(app)) in the jejunum was unaffected by the presence of verapamil; however, the P(app) in the ileum and the colon increased significantly in the presence of verapamil and were similar to the values observed in the jejunum. The results suggest that systemic absorption of tacrolimus from the gastrointestinal tract could be significantly affected by P-gp efflux mechanisms. It is also possible that differences in P-gp function at various intestinal sites in a subject or at a given intestinal site in various subjects could lead to large intra- and interindividual variability in bioavailability of tacrolimus following oral administration. Copyright 2002 Wiley-Liss, Inc. and the American Pharmaceutical Association .

Release from or through a wax matrix system. IV. Generalized expression of the release process for a reservoir device tablet.

PubMed

Yonezawa, Yorinobu; Ishida, Sumio; Suzuki, Shinobu; Sunada, Hisakazu

2002-09-01

Generalization of the release process through the wax matrix layer was examined by use of a reservoir device tablet. The wax matrix layer of the reservoir device tablet was prepared from a physical mixture of lactose and hydrogenated castor oil to simplify the release properties. Release through the wax matrix layer showed zero-order kinetics in a steady state after a given lag time, and could be divided into two stages. The first stage was the formation process of water channel by dissolving the soluble component in the wax matrix layer. The lag time obtained by applying the square root law equation was well connected with the amount of the matrix layer and mixed weight ratio of components in this layer. The second stage was the zero-order release process of drug in the reservoir through the wax matrix layer, because the effective surface area was fixed. The release rate constants were connected with thickness of the matrix layer and permeability coefficient, and the permeability coefficients were connected with the diffusion coefficient of drug and porosity. Hence the release rate constant could be connected with the amount of matrix layer and the mixed weight ratio of components in the matrix layer. It was therefore suggested that the release process could be generalized using the amount of matrix layer and the mixed weight ratio of components in the matrix layer.

BONE REGENERATION AFTER DEMINERALIZED BONE MATRIX AND CASTOR OIL (RICINUS COMMUNIS) POLYURETHANE IMPLANTATION

PubMed Central

Leite, Fábio Renato Manzolli; Ramalho, Lizeti Toledo de Oliveira

2008-01-01

Innocuous biocompatible materials have been searched to repair or reconstruct bone defects. Their goal is to restore the function of live or dead tissues. This study compared connective tissue and bone reaction when exposed to demineralized bovine bone matrix and a polyurethane resin derived from castor bean (Ricinus communis). Forty-five rats were assigned to 3 groups of 15 animals (control, bovine bone and polyurethane). A cylindrical defect was created on mandible base and filled with bovine bone matrix and the polyurethane. Control group received no treatment. Analyses were performed after 15, 45 and 60 days (5 animals each). Histological analysis revealed connective tissue tolerance to bovine bone with local inflammatory response similar to that of the control group. After 15 days, all groups demonstrated similar outcomes, with mild inflammatory reaction, probably due to the surgical procedure rather than to the material. In the polymer group, after 60 days, scarce multinucleated cells could still be observed. In general, all groups showed good stability and osteogenic connective tissue with blood vessels into the surgical area. The results suggest biocompatibility of both materials, seen by their integration into rat mandible. Moreover, the polyurethane seems to be an alternative in bone reconstruction and it is an inexhaustible source of biomaterial. PMID:19089203

D/H isotope ratios of kerogen, bitumen, oil, and water in hydrous pyrolysis of source rocks containing kerogen types I, II, IIS, and III

USGS Publications Warehouse

Schimmelmann, A.; Lewan, M.D.; Wintsch, R.P.

1999-01-01

Immature source rock chips containing different types of kerogen (I, II, IIS, III) were artificially matured in isotopically distinct waters by hydrous pyrolysis and by pyrolysis in supercritical water. Converging isotopic trends of inorganic (water) and organic (kerogen, bitumen, oil) hydrogen with increasing time and temperature document that water-derived hydrogen is added to or exchanged with organic hydrogen, or both, during chemical reactions that take place during thermal maturation. Isotopic mass-balance calculations show that, depending on temperature (310-381??C), time (12-144 h), and source rock type, between ca. 45 and 79% of carbon-bound hydrogen in kerogen is derived from water. Estimates for bitumen and oil range slightly lower, with oil-hydrogen being least affected by water-derived hydrogen. Comparative hydrous pyrolyses of immature source rocks at 330??C for 72 h show that hydrogen in kerogen, bitumen, and expelled oil/wax ranks from most to least isotopically influenced by water-derived hydrogen in the order IIS > II ~ III > I. Pyrolysis of source rock containing type II kerogen in supercritical water at 381 ??C for 12 h yields isotopic results that are similar to those from hydrous pyrolysis at 350??C for 72 h, or 330??C for 144 h. Bulk hydrogen in kerogen contains several percent of isotopically labile hydrogen that exchanges fast and reversibly with hydrogen in water vapor at 115??C. The isotopic equilibration of labile hydrogen in kerogen with isotopic standard water vapors significantly reduces the analytical uncertainty of D/H ratios when compared with simple D/H determination of bulk hydrogen in kerogen. If extrapolation of our results from hydrous pyrolysis is permitted to natural thermal maturation at lower temperatures, we suggest that organic D/H ratios of fossil fuels in contact with formation waters are typically altered during chemical reactions, but that D/H ratios of generated hydrocarbons are subsequently little or not affected by exchange with water hydrogen at typical reservoir conditions over geologic time. It will be difficult to utilize D/H ratios of thermally mature bulk or fractions of organic matter to quantitatively reconstruct isotopic aspects of paleoclimate and paleoenvironment. Hope resides in compound-specific D/H ratios of thermally stable, extractable biomarkers ('molecular fossils') that are less susceptible to hydrogen exchange with water-derived hydrogen.

Particles of spilled oil-absorbing carbon in contact with water

DOEpatents

Muradov, Nazim [Melbourne, FL

2011-03-29

Hydrogen generator coupled to or integrated with a fuel cell for portable power applications. Hydrogen is produced via thermocatalytic decomposition (cracking, pyrolysis) of hydrocarbon fuels in oxidant-free environment. The apparatus can utilize a variety of hydrocarbon fuels, including natural gas, propane, gasoline, kerosene, diesel fuel, crude oil (including sulfurous fuels). The hydrogen-rich gas produced is free of carbon oxides or other reactive impurities, so it could be directly fed to any type of a fuel cell. The catalysts for hydrogen production in the apparatus are carbon-based or metal-based materials and doped, if necessary, with a sulfur-capturing agent. Additionally disclosed are two novel processes for the production of two types of carbon filaments, and a novel filamentous carbon product. Carbon particles with surface filaments having a hydrophobic property of oil film absorption, compositions of matter containing those particles, and a system for using the carbon particles for cleaning oil spills.

Intercropping for Management of Insect Pests of Castor, Ricinus communis, in the Semi—Arid Tropics of India

PubMed Central

Srinivasa Rao, M.; Venkateswarlu, B.

2012-01-01

Intercropping is one of the important cultural practices in pest management and is based on the principle of reducing insect pests by increasing the diversity of an ecosystem. On—farm experiments were conducted in villages of semi—arid tropical (SAT) India to identify the appropriate combination of castor (Ricinus communis L.) (Malpighiales: Euphorbiaceae) and intercropping in relation to pest incidence. The diversity created by introducing cluster bean, cowpea, black gram, or groundnut as intercrops in castor (1:2 ratio proportions) resulted in reduction of incidence of insect pests, namely semilooper (Achaea janata L.), leaf hopper (Empoasca flavescens Fabricius), and shoot and capsule borer (Conogethes punctiferalis Guenee). A buildup of natural enemies (Microplitis, coccinellids, and spiders) of the major pests of castor was also observed in these intercropping systems and resulted in the reduction of insect pests. Further, these systems were more efficient agronomically and economically, and were thus more profitable than a castor monocrop. PMID:22934569

Solid-State Treatment of Castor Cake Employing the Enzymatic Cocktail Produced from Pleurotus djamor Fungi.

PubMed

Sánchez-Cantú, Manuel; Ortiz-Moreno, Liliana; Ramos-Cassellis, María E; Marín-Castro, Marco; De la Cerna-Hernández, C

2018-06-01

In this work, the enzymatic cocktail produced by Pleurotus djamor fungi extracted at pH of 4.8 and 5.3 was employed for castor cake solid-state treatment. Proximal, X-ray powder diffraction and scanning electron microscopy analysis of the pristine castor cake were carried out. First, Pleurotus djamor stain was inoculated in castor cake for the enzymatic production and the enzymatic activity was determined. The maximum enzymatic activity was identified at days 14 (65.9 UI/gss) and 11 (140.3 UI/gss) for the enzymatic cocktail obtained at pH 5.3 and 4.8, respectively. Then, the enzymatic cocktail obtained at the highest enzymatic activity days was employed directly over castor cake. Lignin was degraded throughout incubation time achieving a 47 and 45% decrease for the cocktail produced at pH 4.8 and 5.3, correspondingly. These results were corroborated by the SEM and XRD analysis where a higher porosity and xylan degradation were perceived throughout the enzymatic treatment.

Comparison of the single dose pharmacokinetics, pharmacodynamics, and safety of two novel oral formulations of dimethandrolone undecanoate (DMAU): a potential oral, male contraceptive.

PubMed

Ayoub, R; Page, S T; Swerdloff, R S; Liu, P Y; Amory, J K; Leung, A; Hull, L; Blithe, D; Christy, A; Chao, J H; Bremner, W J; Wang, C

2017-03-01

Dimethandrolone (DMA, 7α,11β-dimethyl-19-nortestosterone) has both androgenic and progestational activities, ideal properties for a male hormonal contraceptive. In vivo, dimethandrolone undecanoate (DMAU) is hydrolyzed to DMA. We showed previously that single oral doses of DMAU powder in capsule taken with food are well tolerated and effective at suppressing both LH and testosterone (T), but absorption was low. We compared the pharmacokinetics and pharmacodynamics of two new formulations of DMAU, in castor oil and in self-emulsifying drug delivery systems (SEDDS), with the previously tested powder formulation. DMAU was dosed orally in healthy adult male volunteers at two academic medical centers. For each formulation tested in this double-blind, placebo-controlled study, 10 men received single, escalating, oral doses of DMAU (100, 200, and 400 mg) and two subjects received placebo. All doses were evaluated for both fasting and with a high fat meal. All three formulations were well tolerated without clinically significant changes in vital signs, blood counts, or serum chemistries. For all formulations, DMA and DMAU showed higher maximum (p < 0.007) and average concentrations (p < 0.002) at the 400 mg dose, compared with the 200 mg dose. The powder formulation resulted in a lower conversion of DMAU to DMA (p = 0.027) compared with both castor oil and SEDDS formulations. DMAU in SEDDS given fasting resulted in higher serum DMA and DMAU concentrations compared to the other two formulations. Serum LH and sex hormone concentrations were suppressed by all formulations of 200 and 400 mg DMAU when administered with food, but only the SEDDS formulation was effectively suppressed serum T when given fasting. We conclude that while all three formulations of oral DMAU are effective and well tolerated when administered with food, DMAU in oil and SEDDS increased conversion to DMA, and SEDDS may have some effectiveness when given fasting. These properties might be advantageous for the application of DMAU as a male contraceptive. © 2016 American Society of Andrology and European Academy of Andrology.

Gas chromatographic, mass spectrometric and stable carbon isotopic investigations of organic residues of plant oils and animal fats employed as illuminants in archaeological lamps from Egypt.

PubMed

Copley, M S; Bland, H A; Rose, P; Horton, M; Evershed, R P

2005-06-01

Man's use of illuminants in lamps or as torches to extend the working day and range of environments accessible to him would have been a major technological advance in human civilisation. The most obvious evidence for this in the archaeological record comes from pottery and stone vessels showing sooting due to the use of a wick in conjunction with a lipid-based fuel or illuminant. A wide range of potential fuels would have been exploited depending upon availability and burning requirements. Reported herein are the results of chemical investigations of a number of lamps recovered from excavations of the site of Qasr Ibrim, Egypt. Gas chromatographic, mass spectrometric and stable carbon isotopic analyses of both free (solvent extractable) and 'bound'(released from solvent extracted pottery by base treatment) lipids have revealed a wide range of saturated fatty acids, hydroxy fatty acids and alpha, omega-dicarboxylic acids. Examination of the distributions of compounds and comparisons with the fatty acid compositions of modern plant oils have allowed a range of fats and oils to be recognised. Specific illuminants identified include Brassicaceae (Cruciferae) seed oil (most likely radish oil, Raphanus sativus), castor oil (from Ricinus communis), animal fat, with less diagnostic distributions and delta(13)C values being consistent with low stearic acid plant oils, such as linseed (Linum usitatissimum) or sesame (Sesamum indicum) oils. The identifications of the various oils and fats are supported by parallel investigations of illuminant residues produced by burning various oils in replica pottery lamps. The findings are entirely consistent with the classical writers including Strabo, Pliny and Theophrastrus.

Mitochondrial Genomes Reveal Slow Rates of Molecular Evolution and the Timing of Speciation in Beavers (Castor), One of the Largest Rodent Species

PubMed Central

Horn, Susanne; Durka, Walter; Wolf, Ronny; Ermala, Aslak; Stubbe, Annegret; Stubbe, Michael; Hofreiter, Michael

2011-01-01

Background Beavers are one of the largest and ecologically most distinct rodent species. Little is known about their evolution and even their closest phylogenetic relatives have not yet been identified with certainty. Similarly, little is known about the timing of divergence events within the genus Castor. Methodology/Principal Findings We sequenced complete mitochondrial genomes from both extant beaver species and used these sequences to place beavers in the phylogenetic tree of rodents and date their divergence from other rodents as well as the divergence events within the genus Castor. Our analyses support the phylogenetic position of beavers as a sister lineage to the scaly tailed squirrel Anomalurus within the mouse related clade. Molecular dating places the divergence time of the lineages leading to beavers and Anomalurus as early as around 54 million years ago (mya). The living beaver species, Castor canadensis from North America and Castor fiber from Eurasia, although similar in appearance, appear to have diverged from a common ancestor more than seven mya. This result is consistent with the hypothesis that a migration of Castor from Eurasia to North America as early as 7.5 mya could have initiated their speciation. We date the common ancestor of the extant Eurasian beaver relict populations to around 210,000 years ago, much earlier than previously thought. Finally, the substitution rate of Castor mitochondrial DNA is considerably lower than that of other rodents. We found evidence that this is correlated with the longer life span of beavers compared to other rodents. Conclusions/Significance A phylogenetic analysis of mitochondrial genome sequences suggests a sister-group relationship between Castor and Anomalurus, and allows molecular dating of species divergence in congruence with paleontological data. The implementation of a relaxed molecular clock enabled us to estimate mitochondrial substitution rates and to evaluate the effect of life history traits on it. PMID:21307956

Application of polymer-coated metal-insulator-semiconductor sensors for the detection of dissolved hydrogen

NASA Astrophysics Data System (ADS)

Li, Dongmei; Medlin, J. W.; Bastasz, R.

2006-06-01

The detection of dissolved hydrogen in liquids is crucial to many industrial applications, such as fault detection for oil-filled electrical equipment. To enhance the performance of metal-insulator-semiconductor (MIS) sensors for dissolved hydrogen detection, a palladium MIS sensor has been modified by depositing a polyimide (PI) layer above the palladium surface. Response measurements of the PI-coated sensors in mineral oil indicate that hydrogen is sensitively detected, while the effect of interfering gases on sensor response is minimized.

Poor digestibility of fully hydrogenated soybean oil in rats: a potential benefit of hydrogenated fats and oils.

PubMed

Kaplan, R J; Greenwood, C E

1998-05-01

The digestibility and absorption of dietary triacylglycerols are dependent on a number of factors including their fatty acid profile. Data demonstrating poor bioavailability of dietary stearic acid would suggest that hydrogenated oil sources would have lower digestibility coefficients compared with their native oils. To test this hypothesis, postweanling rats were fed one of four diets, formulated to contain 40% of energy as fat (assuming complete bioavailability), for 14 d. The diets only differed by fat type, containing soybean oil (SBO), fully hydrogenated soybean oil (HSB), medium-chain triglyceride oil (MCT), or hydrogenated coconut oil (HCO). Rats fed HSB consumed more food during the last 6 d (155.2 +/- 2.7 g) than those in each of the other groups (MCT: 118.9 +/- 2. 2 g; HCO: 124.7 +/- 3.2 g; SBO: 123.8 +/- 2.3 g), yet, they did not gain more weight. Two-day fecal excretion was almost three times greater in HSB-fed rats than in rats fed any other diet (P < 0.0001) because HSB was very poorly available. The digestibility coefficients (a measure of bioavailability) of the four fats were: HSB (30.9 +/- 1.3%) < HCO (94.5 +/- 0.4%) < SBO (97.0 +/- 0.4%) < MCT (98.7 +/- 0.2%) (P < 0.0007). All rats compensated for the incomplete availability of the fats, as apparent absorbable energy consumed did not differ among diet groups. The present data suggest that HSB only contributes 11.6 kJ/g (most fats contribute approximately 37.7 kJ/g) and that not only manufactured fat substitutes, such as olestra, but also more conventional fats are incompletely available to the body. Foods that currently contain HSB may contribute much less utilizable fat and energy than presently realized.

Production of natural antioxidants from vegetable oil deodorizer distillates: effect of catalytic hydrogenation.

PubMed

Pagani, María Ayelén; Baltanás, Miguel A

2010-02-01

Natural tocopherols are one of the main types of antioxidants found in living creatures, but they also have other critical biological functions. The biopotency of natural (+)-alpha-tocopherol (RRR) is 36% higher than that of the synthetic racemic mixture and 300% higher than the SRR stereoisomer. Vegetable oil deodorizer distillates (DD) are an excellent source of natural tocopherols. Catalytic hydrogenation of DD preconcentrates has been suggested as a feasible route for recovery of tocopherols in high yield. However, it is important to know whether the hydrogenation operation, as applied to these tocopherol-rich mixtures, is capable of preserving the chiral (RRR) character, which is critical to its biopotency. Fortified (i.e., (+)-alpha-tocopherol enriched) sunflower oil and methyl stearate, as well as sunflower oil DD, were fully hydrogenated using commercial Ni and Pd catalysts (120-180 degrees C; 20-60 psig). Products were analyzed by chiral HPLC. Results show that the desired chiral configuration (RRR) is fully retained. Thus, the hydrogenation route can be safely considered as a valid alternative for increasing the efficiency of tocopherol recovery processes from DDs while preserving their natural characteristics.

Promotion of hydrogen-rich gas and phenolic-rich bio-oil production from green macroalgae Cladophora glomerata via pyrolysis over its bio-char.

PubMed

Norouzi, Omid; Jafarian, Sajedeh; Safari, Farid; Tavasoli, Ahmad; Nejati, Behnam

2016-11-01

Conversion of Cladophora glomerata (C. glomerata) as a Caspian Sea's green macroalgae into gaseous, liquid and solid products was carried out via pyrolysis at different temperatures to determine its potential for bio-oil and hydrogen-rich gas production for further industrial utilization. Non-catalytic tests were performed to determine the optimum condition for bio-oil production. The highest portion of bio-oil was retrieved at 500°C. The catalytic test was performed using the bio-char derived at 500°C as a catalyst. Effect of the addition of the algal bio-char on the composition of the bio-oil and also gaseous products was investigated. Pyrolysis derived bio-char was characterized by BET, FESEM and ICP method to show its surface area, porosity, and presence of inorganic metals on its surface, respectively. Phenols were increased from 8.5 to 20.76area% by the addition of bio-char. Moreover, the hydrogen concentration and hydrogen selectivity were also enhanced by the factors of 1.37, 1.59 respectively. Copyright © 2016 Elsevier Ltd. All rights reserved.

Electrocatalytic hydrogenation and hydrodeoxygenation of oxygenated and unsaturated organic compounds

DOEpatents

Jackson, James E.; Lam, Chun Ho; Saffron, Christopher M.; Miller, Dennis J.

2018-04-24

A process and related electrode composition are disclosed for the electrocatalytic hydrogenation and/or hydrodeoxygenation of organic substrates such as biomass-derived bio-oil components by the production of hydrogen atoms on a catalyst surface followed by the reaction of the hydrogen atoms with the organic reactants. Biomass fast pyrolysis-derived bio-oil is a liquid mixture containing hundreds of organic compounds with chemical functionalities that are corrosive to container materials and are prone to polymerization. A high surface area skeletal metal catalyst material such as Raney Nickel can be used as the cathode. Electrocatalytic hydrogenation and/or hydrodeoxygenation convert the organic substrates under mild conditions to reduce coke formation and catalyst deactivation. The process converts oxygen-containing functionalities and unsaturated bonds into chemically reduced forms with an increased hydrogen content. The process is operated at mild conditions, which enables it to be a good means for stabilizing bio-oil to a form that can be stored and transported using metal containers and pipes.

21 CFR 184.1472 - Menhaden oil.

Code of Federal Regulations, 2013 CFR

2013-04-01

... limitations to ensure that total intake of eicosapentaenoic acid or docosahexaenoic acid does not exceed 3.0... source of eicosapentaenoic acid or docosahexaenoic acid. (b) Hydrogenated and partially hydrogenated... Value of Fats and Oils, Cyclohexane—Acetic Acid Method,” which is incorporated by reference in...

21 CFR 184.1472 - Menhaden oil.

Code of Federal Regulations, 2012 CFR

2012-04-01

... limitations to ensure that total intake of eicosapentaenoic acid or docosahexaenoic acid does not exceed 3.0... source of eicosapentaenoic acid or docosahexaenoic acid. (b) Hydrogenated and partially hydrogenated... Value of Fats and Oils, Cyclohexane—Acetic Acid Method,” which is incorporated by reference in...

Electrocoagulation of palm oil mill effluent as wastewater treatment and hydrogen production using electrode aluminum.

PubMed

Nasution, M Ansori; Yaakob, Z; Ali, Ehsan; Tasirin, S M; Abdullah, S R S

2011-01-01

Palm oil mill effluent (POME) is highly polluting wastewater generated from the palm oil milling process. Palm oil mill effluent was used as an electrolyte without any additive or pretreatment to perform electrocoagulation (EC) using electricity (direct current) ranging from 2 to 4 volts in the presence of aluminum electrodes with a reactor volume of 20 L. The production of hydrogen gas, removal of chemical oxygen demand (COD), and turbidity as a result of electrocoagulation of POME were determined. The results show that EC can reduce the COD and turbidity of POME by 57 and 62%, respectively, in addition to the 42% hydrogen production. Hydrogen production was also helpful to remove the lighter suspended solids toward the surface. The production of Al(OH)XHO at the aluminum electrode (anode) was responsible for the flocculation-coagulation process of suspended solids followed by sedimentation under gravity. The production of hydrogen gas from POME during EC was also compared with hydrogen gas production by electrolysis of tap water at pH 4 and tap water without pH adjustment under the same conditions. The main advantage of this study is to produce hydrogen gas while treating POME with EC to reduce COD and turbidity effectively. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Effect of substitution of low linolenic acid soybean oil for hydrogenated soybean oil on fatty acid intake.

PubMed

DiRienzo, Maureen A; Astwood, James D; Petersen, Barbara J; Smith, Kim M

2006-02-01

Low linolenic acid soybean oil (LLSO) has been developed as a substitute for hydrogenated soybean oil to reduce intake of trans FA while improving stability and functionality in processed foods. We assessed the dietary impact of substitution of LLSO for hydrogenated soybean oil (HSBO) used in several food categories. All substitutions were done using an assumption of 100% market penetration. The impact of this substitution on the intake of five FA and trans FA was assessed. Substitution of LLSO for current versions of HSBO resulted in a 45% decrease in intake of trans FA. Impacts on other FA intakes were within the realm of typical dietary intakes. No decrease in intake of alpha-linolenic acid was associated with the use of LLSO in place of HSBO because LLSO substitutes for HSBO that are already low in alpha-linolenic acid.

CASTOR: Cathode/Anode Satellite Thruster for Orbital Repositioning

NASA Technical Reports Server (NTRS)

Mruphy, Gloria A.

2010-01-01

The purpose of CASTOR (Cathode/Anode Satellite Thruster for Orbital Repositioning) satellite is to demonstrate in Low Earth Orbit (LEO) a nanosatellite that uses a Divergent Cusped Field Thruster (DCFT) to perform orbital maneuvers representative of an orbital transfer vehicle. Powered by semi-deployable solar arrays generating 165W of power, CASTOR will achieve nearly 1 km/s of velocity increment over one year. As a technology demonstration mission, success of CASTOR in LEO will pave the way for a low cost, high delta-V orbital transfer capability for small military and civilian payloads in support of Air Force and NASA missions. The educational objective is to engage graduate and undergraduate students in critical roles in the design, development, test, carrier integration and on-orbit operations of CASTOR as a supplement to their curricular activities. This program is laying the foundation for a long-term satellite construction program at MIT. The satellite is being designed as a part of AFRL's University Nanosatellite Program, which provides the funding and a framework in which student satellite teams compete for a launch to orbit. To this end, the satellite must fit within an envelope of 50cmx50cmx60cm, have a mass of less than 50kg, and meet stringent structural and other requirements. In this framework, the CASTOR team successfully completed PDR in August 2009 and CDR in April 2010 and will compete at FCR (Flight Competition Review) in January 2011. The complexity of the project requires implementation of many systems engineering techniques which allow for development of CASTOR from conception through FCR and encompass the full design, fabrication, and testing process.

Catalytic cracking of a Wilmington vacuum oil gas and selected hydrotreated products: Topical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wells, J.W.; Zagula, E.J.

1987-05-01

The catalytic cracking of a Wilmington vacuum gas oil and the products from mild hydrotreating and severe hydrotreating of this gas oil was evaluated over a low metal equilibrium catalyst in a microconfined bed unit (MCBU). Two levels of catalytic cracking severity were evaluated for these three samples. The performance and product analysis showed that hydrotreating improves the quality of catalytic cracker feedstock and the resultant products. The results also indicated that a level of hydrotreating exists above which the quality of the liquid products and the yields of coke and heavy oil are not affected significantly by the severitymore » of the catalytic cracking process. As expected, the sulfur and nitrogen content of the liquid products (gasolines, light cycle oil, and heavy cycle oil) were found to decrease as the severity of the feed hydrotreating increased. The distribution of sulfur and nitrogen in the liquid products was found to be independent of cracking conditions or product yields for a given level of hydrogenation. Analysis of the gas products shows that the degree of hydrogen transfer increases with the severity of hydrogenation. As cracking severity increases, the apparent degree of hydrogen transfer decreases, and the concentration of olefinic compounds increases relative to the saturated compounds. In the future, these results will be compared to similar results from a Mayan vacuum gas oil. 10 refs., 17 figs., 10 tabs.« less

Influence of indigenous minor components on fat crystal network of fully hydrogenated palm kernel oil and fully hydrogenated coconut oil.

PubMed

Chai, Xiu-Hang; Meng, Zong; Cao, Pei-Rang; Liang, Xin-Yu; Piatko, Michael; Campbell, Shawn; Koon Lo, Seong; Liu, Yuan-Fa

2018-07-30

Purification of triglycerides from fully hydrogenated palm kernel oil (FHPKO) and fully hydrogenated coconut oil (FHCNO) was performed by a chromatographic method. Lipid composition, thermal properties, polymorphism, isothermal crystallization behaviour, nanostructure and microstructure of FHPKO, FHPKO-triacylglycerol (TAG), FHCNO and FHCNO-TAG were evaluated. Removal of minor components had no effect on triglycerides composition. However, the presence of the minor components did increase the slip melting point and promote onset of crystallization. Furthermore, the thickness of the nanoscale crystals increased, and polymorphic transformation from β' to β occurred in FHPKO after the removal of minor components, and from α to β' in FHCNO. Sharp changes in the values of the Avrami constant K and exponent n suggested that the presence of minor components changed the crystal growth mechanism. The PLM results indicated that a coarser crystal structure with lower fractal dimension appeared after the removal of minor components from both FHPKO and FHCNO. Copyright © 2018 Elsevier Ltd. All rights reserved.

Antiproliferative activity of synthetic fatty acid amides from renewable resources.

PubMed

dos Santos, Daiane S; Piovesan, Luciana A; D'Oca, Caroline R Montes; Hack, Carolina R Lopes; Treptow, Tamara G M; Rodrigues, Marieli O; Vendramini-Costa, Débora B; Ruiz, Ana Lucia T G; de Carvalho, João Ernesto; D'Oca, Marcelo G Montes

2015-01-15

In the work, the in vitro antiproliferative activity of a series of synthetic fatty acid amides were investigated in seven cancer cell lines. The study revealed that most of the compounds showed antiproliferative activity against tested tumor cell lines, mainly on human glioma cells (U251) and human ovarian cancer cells with a multiple drug-resistant phenotype (NCI-ADR/RES). In addition, the fatty methyl benzylamide derived from ricinoleic acid (with the fatty acid obtained from castor oil, a renewable resource) showed a high selectivity with potent growth inhibition and cell death for the glioma cell line-the most aggressive CNS cancer. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effect of gamma irradiation on cell lysis and polyhydroxyalkanoate produced by Bacillus flexus

NASA Astrophysics Data System (ADS)

Divyashree, M. S.; Shamala, T. R.

2009-02-01

Bacillus flexus cultivated on sucrose and sucrose with plant oil such as castor oil produced polyhydroxybutyrate (PHB), a homopolymer of polyhydroxyalkanoate (PHA) and PHA copolymer (containing hydroxybutyrate and hexanoate), respectively. Gamma irradiation of these cells (5-40 kGy) resulted in cell damage and aided in the isolation of 45% and 54% PHA on biomass weight, correspondingly. Molecular weight of PHB increased from 1.5×10 5 to 1.9×10 5 after irradiation (10 kGy), with marginal increase of tensile strength from 18 to 20 MPa. At the same irradiation dosage, PHA copolymer showed higher molecular weight increase from 1.7×10 5 to 2.3×10 5 and tensile strength from 20 to 35 MPa. GC, GC-MS, FTIR and 1H NMR were used for the characterization of PHA. Gamma irradiation seems to be a novel technique, to induce cross-linking and molecular weight increase of PHA copolymer and aid in easy extractability of intracellular PHA, simultaneously.

Curcumin phytosomal softgel formulation: Development, optimization and physicochemical characterization.

PubMed

Allam, Ahmed N; Komeil, Ibrahim A; Abdallah, Ossama Y

2015-09-01

Curcumin, a naturally occurring lipophilic molecule can exert multiple and diverse bioactivities. However, its limited aqueous solubility and extensive presystemic metabolism restrict its bioavailability. Curcumin phytosomes were prepared by a simple solvent evaporation method where free flowing powder was obtained in addition to a newly developed semisolid formulation to increase curcumin content in softgels. Phytosomal powder was characterized in terms of drug content and zeta potential. Thirteen different softgel formulations were developed using oils such as Miglyol 812, castor oil and oleic acid, a hydrophilic vehicle such as PEG 400 and bioactive surfactants such as Cremophor EL and KLS P 124. Selected formulations were characterized in terms of curcumin in vitro dissolution. TEM analysis revealed good stability and a spherical, self-closed structure of curcumin phytosomes in complex formulations. Stability studies of chosen formulations prepared using the hydrophilic vehicle revealed a stable curcumin dissolution pattern. In contrast, a dramatic decrease in curcumin dissolution was observed in case of phytosomes formulated in oily vehicles.

Screening of lipid composition for scalable fabrication of solvent free lipid microarrays

NASA Astrophysics Data System (ADS)

Ghazanfari, Lida; Lenhert, Steven

2016-12-01

Liquid microdroplet arrays on surfaces are a promising approach to the miniaturization of laboratory processes such as high throughput screening. The fluid nature of these droplets poses unique challenges and opportunities in their fabrication and application, particularly for the scalable integration of multiple materials over large areas and immersion into cell culture solution. Here we use pin spotting and nanointaglio printing to screen a library of lipids and their mixtures for their compatibility with these fabrication processes, as well as stability upon immersion into aqueous solution. More than 200 combinations of natural and synthetic oils composed of fatty acids, triglycerides, and hydrocarbons were tested for their pin-spotting and nanointaglio print quality and their ability to contain the fluorescent compound TRITC upon immersion in water. A combination of castor oil and hexanoic acid at the ratio of 1:1 (w/w) was found optimal for producing reproducible patterns that are stable upon immersion into water. This method is capable of large scale nano-materials integration.

Oil-free centrifugal hydrogen compression technology demonstration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heshmat, Hooshang

2014-05-31

One of the key elements in realizing a mature market for hydrogen vehicles is the deployment of a safe and efficient hydrogen production and delivery infrastructure on a scale that can compete economically with current fuels. The challenge, however, is that hydrogen, being the lightest and smallest of gases with a lower viscosity and density than natural gas, readily migrates through small spaces and is difficult to compresses efficiently. While efficient and cost effective compression technology is crucial to effective pipeline delivery of hydrogen, the compression methods used currently rely on oil lubricated positive displacement (PD) machines. PD compression technologymore » is very costly, has poor reliability and durability, especially for components subjected to wear (e.g., valves, rider bands and piston rings) and contaminates hydrogen with lubricating fluid. Even so called “oil-free” machines use oil lubricants that migrate into and contaminate the gas path. Due to the poor reliability of PD compressors, current hydrogen producers often install duplicate units in order to maintain on-line times of 98-99%. Such machine redundancy adds substantially to system capital costs. As such, DOE deemed that low capital cost, reliable, efficient and oil-free advanced compressor technologies are needed. MiTi’s solution is a completely oil-free, multi-stage, high-speed, centrifugal compressor designed for flow capacity of 500,000 kg/day with a discharge pressure of 1200 psig. The design employs oil-free compliant foil bearings and seals to allow for very high operating speeds, totally contamination free operation, long life and reliability. This design meets the DOE’s performance targets and achieves an extremely aggressive, specific power metric of 0.48 kW-hr/kg and provides significant improvements in reliability/durability, energy efficiency, sealing and freedom from contamination. The multi-stage compressor system concept has been validated through full scale performance testing of a single stage with helium similitude gas at full speed in accordance with ASME PTC-10. The experimental results indicated that aerodynamic performance, with respect to compressor discharge pressure, flow, power and efficiency exceeded theoretical prediction. Dynamic testing of a simulated multistage centrifugal compressor was also completed under a parallel program to validate the integrity and viability of the system concept. The results give strong confidence in the feasibility of the multi-stage design for use in hydrogen gas transportation and delivery from production locations to point of use.« less

Mitigation of Ricin Contamination in Soils: Sorption and Degradation

DTIC Science & Technology

2003-07-01

Table 2. Castor impacts on fungal taxonomic diversity: Total activity Dominate fungi Castor field: Fusarium (several species) Lower species...richness Cotton field: Trichoderma Fusarium Sterile dark Higher species richness

EFFECT OF THE LEVEL AND TYPE OF DIETARY FAT ON THE METABOLISM OF CHOLESTEROL AND BETA LIPOPROTEINS IN THE CEBUS MONKEY

PubMed Central

Portman, Oscar W.; Hegsted, D. Mark; Stare, Fredrick J.; Bruno, Dorothy; Murphy, Robert; Sinisterra, Leonardo

1956-01-01

A study was carried out to determine the effect of the level and type of dietary fat on the concentration of cholesterol and beta lipoproteins in the sera of Cebus monkeys. Three groups of monkeys were fed isocaloric diets containing a fixed ratio of alpha protein and cholesterol to calories but with different amounts of corn oil and sucrose. Corn oil provided 10, 32, and 45 per cent of the calories in the three diets, and the level of sucrose was varied inversely. After 8 weeks the serum cholesterol and Sf 12 to 100 beta lipoprotein concentrations were significantly greater in the medium and high fat groups. When corn oil was decreased from 45 to 10 per cent of dietary calories and sucrose was increased, the serum cholesterol fell in all cases, and when the reverse change was made, the concentration of serum cholesterol increased. Variation in dietary sucrose had no specific effect. Substitution of starch for sucrose with diets otherwise constant did not cause significant change in the concentration of serum cholesterol. When monkeys fed corn oil diets at any of three levels were changed to hydrogenated cottonseed oil diets at the same level, the serum cholesterol and Sf 12 to 100 beta lipoproteins rose. However, hydrogenated cottonseed oil had no greater hypercholesteremic effect than did corn oil in the absence of dietary cholesterol. Diets containing lard with cholesterol also produced strikingly greater serum lipide responses than did diets based on corn oil and cholesterol. Hydrogenated cottonseed oil had a greater hypercholesteremic effect than an unhydrogenated cottonseed oil from the same lot. Preliminary studies indicated that the saturated fats (hydrogenated cottonseed oil) produced the most striking elevation of serum cholesterol values (above controls fed corn oil) when casein was the dietary protein. PMID:13376806

Techno-economic and resource analysis of hydroprocessed renewable jet fuel.

PubMed

Tao, Ling; Milbrandt, Anelia; Zhang, Yanan; Wang, Wei-Cheng

2017-01-01

Biomass-derived jet fuel is an alternative jet fuel (AJF) showing promise of reducing the dependence on fossil fuel and greenhouse gas emissions. Hydroprocessed esters and fatty acids (HEFA) concept is also known as one of the pathways for producing bio jet fuel. HEFA fuel was approved by the American Society for Testing and Materials in 2011, and can be blended up to 50% with conventional jet fuel. Since then, several HEFA economic and life-cycle assessments have been published in literature. However, there have been limited analyses on feedstock availability, composition, and their impact on hydrocarbon yield (particularly jet blendstock yield) and overall process economics. This study examines over 20 oil feedstocks, their geographic distribution and production levels, oil yield, prices, and chemical composition. The results of our compositional analysis indicate that most oils contain mainly C 16 and C 18 fatty acids except pennycress, yellow grease, and mustard, which contain higher values and thus would require hydrocracking to improve jet fuel production. Coconut oil has a large content of shorter carbon fatty acids, making it a good feedstock candidate for renewable gasoline instead of jet substitutes' production. Techno-economic analysis (TEA) was performed for five selected oil feedstocks-camelina, pennycress, jatropha, castor bean, and yellow grease-using the HEFA process concept. The resource analysis indicates that oil crops currently grown in the United States (namely soybean) have relatively low oil yield when compared to oil crops grown in other parts of the world, such as palm, coconut, and jatropha. Also, non-terrestrial oil sources, such as animal fats and greases, have relatively lower prices than terrestrial oil crops. The minimum jet fuel selling price for these five resources ranges between $3.8 and $11.0 per gallon. The results of our TEA and resource studies indicate the key cost drivers for a biorefinery converting oil to jet hydrocarbons are as follows: oil price, conversion plant capacity, fatty acid profile, addition of hydrocracker, and type of hydroprocessing catalysts.

Fuel cell commercialization: The key to a hydrogen economy

NASA Astrophysics Data System (ADS)

Zegers, P.

With the current level of global oil production, oil reserves will be sufficient for 40 years. However, due to the fact that the global GDP will have increased by a factor seven in 2050, oil reserves are likely to be exhausted in a much shorter time period. The EU and car industry aim at a reduction of the consumption of oil, at energy savings (with a key role for fuel cells) and an increased use of hydrogen from natural gas and, possibly, coal, in the medium term. The discovery of huge methane resources as methane hydrates (20 times those of oil, gas and coal together) in oceans at 1000-3000 m depth could be of major importance. In the long term, the EU aims at a renewable energy-based energy supply. The European Hydrogen and Fuel Cell Technology Platform is expected to play a major role in bringing about a hydrogen economy. The availability of commercial fuel cells is here a prerequisite. However, after many years of research, fuel cells have not yet been commercialized. If they will not succeed to enter the market within 5 years there is a real danger that activities aiming at a hydrogen society will peter out. In a hydrogen strategy, high priority should therefore be given to actions which will bring about fuel cell commercialization within 5 years. They should include the identification of fuel cell types and (niche) markets which are most favorable for a rapid market introduction. These actions should include focused short-term RTD aiming at cost reduction and increased reliability.

Hydrogenation of cottonseed oil with nickel, palladium and platinum catalysts

USDA-ARS?s Scientific Manuscript database

A number of commercial catalysts have been used to study hydrogenation of cottonseed oil, with the goal of minimizing trans fatty acid (TFA) content. Despite the different temperatures used, catalyst levels, and reaction times, the data from each catalyst type fall on the same curve when the TFA le...

21 CFR 186.1551 - Hydrogenated fish oil.

Code of Federal Regulations, 2011 CFR

2011-04-01

... used for dry food packaging. (d) The ingredient is used at levels not to exceed good manufacturing... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Hydrogenated fish oil. 186.1551 Section 186.1551 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD...

Effects of dietary supplementation with ghee, hydrogenated oil, or olive oil on lipid profile and fatty streak formation in rabbits

PubMed Central

Hosseini, Mohsen; Asgary, Sedigheh

2012-01-01

BACKGROUND Coronary heart disease is the leading cause of mortality worldwide. A high-fat diet, rich in saturated fatty acids and low in polyunsaturated fatty acids, is said to be an important cause of atherosclerosis and cardiovascular diseases. METHODS In this experimental study, 40 male rabbits were randomly assigned to eight groups of five to receive normal diet, hypercholesterolemic diet, normal diet plus ghee, normal diet plus olive oil, normal diet plus hydrogenated oil, hypercholesterolemic diet plus ghee, hypercholesterolemic diet plus olive oil, and hypercholesterolemic diet plus hydrogenated oil. They received rabbit chow for a period of 12 weeks. At the start and end of the study, fasting blood samples were taken from all animals to measure biochemical factors including total cholesterol (TC), low-density lipoprotein (LDL), high-density lipoprotein (HDL), triglyceride (TG), fasting blood sugar (FBS), and C-reactive protein (CRP). Moreover, aorta, left and right coronary arteries were dissected at the end of the study to investigate fatty streak formation (FSF). Data was analyzed in SPSS at a significance level of 0.05. RESULTS In rabbits under normal diet, ghee significantly increased TC, LDL, and HDL compared to the beginning (P < 0.01) and also to the other two types of fat (P < 0.05). Moreover, normal diet plus olive oil significantly enhanced FSF in left coronary arteries and aorta compared to normal diet plus ghee. In groups receiving hypercholesterolemic diets, ghee significantly increased HDL and CRP (P < 0.05) and significantly decreased FBS (P < 0.01). The hypecholesterolemic diet plus olive oil significantly increased HDL (P < 0.01). Supplementation of hypecholesterolemic diet with ghee significantly increased HDL and FBS in comparison with hydrogenated oil. Significant increase of FBS was also detected with the use of ghee compared to olive oil. Ghee also significantly reduced FSF in left and right coronary arteries compared to olive oil. FSF in left coronary arteries was significantly lower in the hypecholesterolemic diet plus ghee group compared to the hypecholesterolemic diet plus hydrogenated oil group. CONCLUSION According to the achieved results, future clinical trial studies and investigation of other risk factors such as inflammatory factors are required. PMID:23358722

Final report on the safety assessment of Cocos nucifera (coconut) oil and related ingredients.

PubMed

Burnett, Christina L; Bergfeld, Wilma F; Belsito, Donald V; Klaassen, Curtis D; Marks, James G; Shank, Ronald C; Slaga, Thomas J; Snyder, Paul W; Andersen, F Alan

2011-05-01

Cocos nucifera (coconut) oil, oil from the dried coconut fruit, is composed of 90% saturated triglycerides. It may function as a fragrance ingredient, hair conditioning agent, or skin-conditioning agent and is reported in 626 cosmetics at concentrations from 0.0001% to 70%. The related ingredients covered in this assessment are fatty acids, and their hydrogenated forms, corresponding fatty alcohols, simple esters, and inorganic and sulfated salts of coconut oil. The salts and esters are expected to have similar toxicological profiles as the oil, its hydrogenated forms, and its constituent fatty acids. Coconut oil and related ingredients are safe as cosmetic ingredients in the practices of use and concentration described in this safety assessment.

Preliminary investigation on the production of fuels and bio-char from Chlamydomonas reinhardtii biomass residue after bio-hydrogen production.

PubMed

Torri, Cristian; Samorì, Chiara; Adamiano, Alessio; Fabbri, Daniele; Faraloni, Cecilia; Torzillo, Giuseppe

2011-09-01

The aim of this work was to investigate the potential conversion of Chlamydomonas reinhardtii biomass harvested after hydrogen production. The spent algal biomass was converted into nitrogen-rich bio-char, biodiesel and pyrolysis oil (bio-oil). The yield of lipids (algal oil), obtained by solvent extraction, was 15 ± 2% w/w(dry-biomass). This oil was converted into biodiesel with a 8.7 ± 1% w/w(dry-biomass) yield. The extraction residue was pyrolysed in a fixed bed reactor at 350 °C obtaining bio-char as the principal fraction (44 ± 1% w/w(dry-biomass)) and 28 ± 2% w/w(dry-biomass) of bio-oil. Pyrolysis fractions were characterized by elemental analysis, while the chemical composition of bio-oil was fully characterized by GC-MS, using various derivatization techniques. Energy outputs resulting from this approach were distributed in hydrogen (40%), biodiesel (12%) and pyrolysis fractions (48%), whereas bio-char was the largest fraction in terms of mass. Copyright © 2011 Elsevier Ltd. All rights reserved.

Theoretical investigation of isotope exchange reaction in tritium-contaminated mineral oil in vacuum pump.

PubMed

Dong, Liang; Xie, Yun; Du, Liang; Li, Weiyi; Tan, Zhaoyi

2015-04-28

The mechanism of the isotope exchange reaction between molecular tritium and several typical organic molecules in vacuum pump mineral oil has been investigated by density functional theory (DFT), and the reaction rates are determined by conventional transition state theory (TST). The tritium-hydrogen isotope exchange reaction can proceed with two different mechanisms, the direct T-H exchange mechanism and the hyrogenation-dehydrogenation exchange mechanism. In the direct exchange mechanism, the titrated product is obtained through one-step via a four-membered ring hydrogen migration transition state. In the hyrogenation-dehydrogenation exchange mechanism, the T-H exchange could be accomplished by the hydrogenation of the unsaturated bond with tritium followed by the dehydrogenation of HT. Isotope exchange between hydrogen and tritium is selective, and oil containing molecules with OH and COOH groups can more easily exchange hydrogen for tritium. For aldehydes and ketones, the ability of T-H isotope exchange can be determined by the hydrogenation of T2 or the dehydrogenation of HT. The molecules containing one type of hydrogen provide a single product, while the molecules containing different types of hydrogens provide competitive products. The rate constants are presented to quantitatively estimate the selectivity of the products. Copyright © 2015 Elsevier B.V. All rights reserved.

The mixture of cashew nut shell liquid and castor oil results in an efficient larvicide against Aedes aegypti that does not alter embryo-fetal development, reproductive performance or DNA integrity

PubMed Central

Vani, Juliana Miron; Monreal, Maria Tereza Ferreira Duenhas; Auharek, Sarah Alves; Cunha-Laura, Andréa Luiza; de Arruda, Eduardo José; Lima, Alessandra Ramos; da Silva, Cicera Maria; Antoniolli-Silva, Andréia Conceição Milan Brochado; de Lima, Dênis Pires; Beatriz, Adilson

2018-01-01

Dengue fever, chikungunya fever and Zika virus are epidemics in Brazil that are transmitted by mosquitoes, such as Aedes aegypti or Aedes albopictus. The liquid from shells of cashew nuts is attractive for its important biological and therapeutic activities, which include toxicity to mosquitoes of the genus Aedes. The present study evaluated the effects of a mixture of surfactants from natural cashew nutshell liquid and castor oil (named TaLCC-20) on the mortality of larvae and on the reproductive performance, embryonic and fetal development and genetic stability of Swiss mice. A total of 400 Ae. aegypti larvae (third larval stage) were treated with TaLCC-20 concentrations of 0.05 mg/L, 0.5 mg/L, or 5 mg/L (ppm). Twenty pregnant female mice were also orally administered TaLCC-20 at doses of 5 mg/kg and 50 mg/kg body weight (b.w.), and 10 animals were given only drinking water at 0.1 mL/10 g b.w. (orally). The results of a larvicide test demonstrated that 5 mg/mL TaLCC-20 killed 100% of larvae within three hours, which is comparable to the gold standard indicated by the Ministry of Health. Overall, these results show that TaLCC-20 is an efficient larvicide that does not induce genetic damage. In addition, changes in reproductive performance and embryo-fetal development appear positive, and the formulation is cost effective. Therefore, TaLCC-20 is an important product in the exploration of natural larvicides and can assist in fighting mosquitos as vectors for dengue fever, chikungunya fever and Zika virus, which are emerging/re-emerging and require proper management to ensure minimal harm to the human population. Therefore, TaLCC-20 can be considered a key alternative to commercial products, which are effective yet toxigenic. PMID:29554095

Pharmacological evaluation of Musa seminifera Lour. fruit.

PubMed

Saha, Sanjib; Hossain, Faroque; Anisuzzman, Md; Islam, Md Khirul

2013-07-01

To study potential antioxidant, analgesic, antidiarrheal, and antibacterial activities of the ethanol extract of Musa seminifera Lour. fruit in different established in vivo and in vitro experimental models. In vitro antioxidant activity was studied in 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical-scavenging assay. Phenolic content was determined using Folin-Ciocalteu's reagent. Reducing ability was evaluated by ferric reducing power assay. Peripherally and centrally acting analgesic activity was studied in three different in vivo models, namely, acetic acid-induced writhing, hot-plate test, and tail-flick test in Swiss albino mice. In vivo antidiarrheal activity was evaluated in castor oil- and magnesium sulfate-induced diarrhea in mice. Gastrointestinal motility test was also carried out in mice. All studies in mice were undertaken at the doses of 250 and 500 mg/kg body weight. Antibacterial activity was assessed by disk diffusion assay against some Gram-positive and Gram-negative bacterial strains. Acute toxicity test was conducted to assess the safe doses of the extract. The extract showed 50% inhibitory concentration value of 12.65 μg/mL in DPPH radical-scavenging assay. Phenolic content was found to be 589.83 mg gallic acid equivalent per 100 g of dried fruits extract. Reducing power was in a concentration-dependent manner, and strongly comparable with the standard ascorbic acid. The extract demonstrated significant inhibition of writhing in acetic acid-induced writhing test at both dose levels (P<0.01). The extract also raised pain threshold in both hot-plate and tail-flick test in a dose-dependent manner, and the results were statistically significant (P<0.01). The extract significantly (P<0.01) increased latent period, and decreased defecation in both castor oil- and magnesium sulfate-induced diarrhea. The extract also decreased gastrointestinal motility in mice. In disk diffusion assay, the extract showed potential antibacterial activity against all the tested bacterial strains. The results suggest that the ethanol extract of M. seminifera fruit has potential antioxidant, analgesic, antidiarrheal, and antibacterial activities.

The mixture of cashew nut shell liquid and castor oil results in an efficient larvicide against Aedes aegypti that does not alter embryo-fetal development, reproductive performance or DNA integrity.

PubMed

Vani, Juliana Miron; Monreal, Maria Tereza Ferreira Duenhas; Auharek, Sarah Alves; Cunha-Laura, Andréa Luiza; de Arruda, Eduardo José; Lima, Alessandra Ramos; da Silva, Cicera Maria; Antoniolli-Silva, Andréia Conceição Milan Brochado; de Lima, Dênis Pires; Beatriz, Adilson; Oliveira, Rodrigo Juliano

2018-01-01

Dengue fever, chikungunya fever and Zika virus are epidemics in Brazil that are transmitted by mosquitoes, such as Aedes aegypti or Aedes albopictus. The liquid from shells of cashew nuts is attractive for its important biological and therapeutic activities, which include toxicity to mosquitoes of the genus Aedes. The present study evaluated the effects of a mixture of surfactants from natural cashew nutshell liquid and castor oil (named TaLCC-20) on the mortality of larvae and on the reproductive performance, embryonic and fetal development and genetic stability of Swiss mice. A total of 400 Ae. aegypti larvae (third larval stage) were treated with TaLCC-20 concentrations of 0.05 mg/L, 0.5 mg/L, or 5 mg/L (ppm). Twenty pregnant female mice were also orally administered TaLCC-20 at doses of 5 mg/kg and 50 mg/kg body weight (b.w.), and 10 animals were given only drinking water at 0.1 mL/10 g b.w. (orally). The results of a larvicide test demonstrated that 5 mg/mL TaLCC-20 killed 100% of larvae within three hours, which is comparable to the gold standard indicated by the Ministry of Health. Overall, these results show that TaLCC-20 is an efficient larvicide that does not induce genetic damage. In addition, changes in reproductive performance and embryo-fetal development appear positive, and the formulation is cost effective. Therefore, TaLCC-20 is an important product in the exploration of natural larvicides and can assist in fighting mosquitos as vectors for dengue fever, chikungunya fever and Zika virus, which are emerging/re-emerging and require proper management to ensure minimal harm to the human population. Therefore, TaLCC-20 can be considered a key alternative to commercial products, which are effective yet toxigenic.

Antidiarrhoea and toxicological evaluation of the leaf extract of Dissotis rotundifolia triana (Melastomataceae)

PubMed Central

2010-01-01

Background The leaves of Dissotis rotundifolia are used ethnomedically across Africa without scientific basis or safety concerns. Determination of its phytochemical constituents, antimicrobial activity, effects on the gastrointestinal tract (GIT) as well as toxicological profile will provide supportive scientific evidence in favour of its continous usage. Method Chemical and chromatographic tests were employed in phytochemical investigations. Inhibitory activity against clinical strains of Escherichia coli, Pseudomonas aeruginosa, Staphylococcus aureus and Salmonella typhi were compared with Gentamycin. Our report includes minimum inhibitory concentration (MIC) against the tested organisms. The effect of the ethanol extract on the motility of the GIT in mice using the charcoal plug method and castor oil induced diarrhoea in rats was evaluated. Toxicological evaluation was determined by administering 250 mg/kg and 500 mg/kg of extracts on male Wistar rats for 14 days with normal saline as control. The tissues of the kidneys, liver, heart and testes were examined. Results Phytochemical studies revealed the presence of alkaloids, saponin and cardiac glycosides. The crude ethanol extract and fractions inhibited the growth of E. coli, P. aeruginosa, S. aureus and S. typhi to varying extents. The degree of transition exhibited by the charcoal meal was dose-dependent. In the castor oil induced diarrhoea test, all the doses showed anti-spasmodic effects. The LD50 in mice was above 500 mg/kg body weight. Toxicological evaluation at 500 mg/kg showed increased cytoplasmic eosinophilia and densely stained nuclei of the liver, tubular necrosis of the kidney, presence of ill-defined testes with indistinct cell outlines and no remarkable changes in the heart. Conclusion Ethanol extracts of Dissotis rotundifolia have demonstrated antimicrobial activity against clinical strains of selected microorganisms. The plant showed potential for application in the treatment of diarrhoea, thereby justifying its usage across Africa. It also demonstrated toxicity in certain organs at the dose of 500 mg/kg, and it will be necessary to fully establish its safety profile. PMID:21083876

Antidiarrhoea and toxicological evaluation of the leaf extract of Dissotis rotundifolia Triana (Melastomataceae).

PubMed

Abere, Tavs A; Okoto, Pius E; Agoreyo, Freddy O

2010-11-17

The leaves of Dissotis rotundifolia are used ethnomedically across Africa without scientific basis or safety concerns. Determination of its phytochemical constituents, antimicrobial activity, effects on the gastrointestinal tract (GIT) as well as toxicological profile will provide supportive scientific evidence in favour of its continous usage. Chemical and chromatographic tests were employed in phytochemical investigations. Inhibitory activity against clinical strains of Escherichia coli, Pseudomonas aeruginosa, Staphylococcus aureus and Salmonella typhi were compared with Gentamycin. Our report includes minimum inhibitory concentration (MIC) against the tested organisms. The effect of the ethanol extract on the motility of the GIT in mice using the charcoal plug method and castor oil induced diarrhoea in rats was evaluated. Toxicological evaluation was determined by administering 250 mg/kg and 500 mg/kg of extracts on male Wistar rats for 14 days with normal saline as control. The tissues of the kidneys, liver, heart and testes were examined. Phytochemical studies revealed the presence of alkaloids, saponin and cardiac glycosides. The crude ethanol extract and fractions inhibited the growth of E. coli, P. aeruginosa, S. aureus and S. typhi to varying extents. The degree of transition exhibited by the charcoal meal was dose-dependent. In the castor oil induced diarrhoea test, all the doses showed anti-spasmodic effects. The LD50 in mice was above 500 mg/kg body weight. Toxicological evaluation at 500 mg/kg showed increased cytoplasmic eosinophilia and densely stained nuclei of the liver, tubular necrosis of the kidney, presence of ill-defined testes with indistinct cell outlines and no remarkable changes in the heart. Ethanol extracts of Dissotis rotundifolia have demonstrated antimicrobial activity against clinical strains of selected microorganisms. The plant showed potential for application in the treatment of diarrhoea, thereby justifying its usage across Africa. It also demonstrated toxicity in certain organs at the dose of 500 mg/kg, and it will be necessary to fully establish its safety profile.

In Vivo Anti-Inflammatory, Anti-Bacterial and Anti-Diarrhoeal Activity of Ziziphus Jujuba Fruit Extract.

PubMed

Mesaik, Ahmed M; Poh, Hiap Wei; Bin, Ooi Yan; Elawad, Izzaddinn; Alsayed, Badr

2018-05-20

Ziziphus jujuba belongs to family Rhamnaceae widely distributed in subtropical and tropical countries. It is used traditionally for several pharmacological purposes including anti-inflammation, antidiarrhoeal and antibacterial, as well as tonic and sometimes as hypnotic (sedative). To determine the in vivo antidiarrhoeal, antibacterial and anti-inflammatory activities of Z. jujuba fruit ethanolic extract. The fruit was macerated and extracted by 95% (v/v) ethanol. The antidiarrhoeal activity was evaluated using castor oil and Escherichia coli induced diarrhoea mouse model. The antidiarrhoeal and antibacterial activity was investigated at graded doses (400-1200 mg/kg). The anti-inflammatory effects were tested using the carrageenan-induced paw oedema in female Wistar rats. Rat's treatment groups received tragacanth, 100 mg/kg diclofenac sodium, 800 mg/kg, 1200 mg/kg or 1600 mg/kg of an ethanolic extract of Z. jujuba (EEZJ). All treatment groups were fed with the compounds one hour before carrageenan injection at of rat's paw. Also, the EEZJ was further analysed by HPLC-PDA system for identification of the presence of betulinic acid and quercetin. EEZJ different doses did not show inhibitory activity against castor oil induced diarrhoea except for the higher (1200 mg/kg) dose. However, the frequency of defecation of stools and watery stool were reduced significantly when compared to control group (P ≤ 0.05 and P ≤ 0.01 respectively), resulted in overall 67% inhibition of diarrhoea. Our anti-inflammatory results demonstrated that EEZJ was able to inhibit the carrageenan-induced paw oedema in rats to a significant degree (p ≤ 0.05) and the paw volume and thickness of both left and right paw were affected compared to the negative control group. EEZJ possesses antidiarrhoeal and antibacterial activity in a dose depending manner and may provide a pharmacological basis for its clinical use in diarrheal diseases. The activity may partially be due to the presence of betulinic acid and quercetin.

Neonatal Exposure to Bisphenol A Alters Reproductive Parameters and Gonadotropin Releasing Hormone Signaling in Female Rats

PubMed Central

Fernández, Marina; Bianchi, Maria; Lux-Lantos, Victoria; Libertun, Carlos

2009-01-01

Background Bisphenol A (BPA) is a component of polycarbonate plastics, epoxy resins, and polystyrene and is found in many products. Several reports have revealed potent in vivo effects, because BPA acts as an estrogen agonist and/or antagonist and as an androgen and thyroid hormone antagonist. Objectives We analyzed the effects of neonatal exposure to BPA on the reproductive axis of female Sprague-Dawley rats. Methods Female rats were injected subcutaneusly, daily, from postnatal day 1 (PND1) to PND10 with BPA [500 μg/50 μL (high) or 50 μg/50 μL (low)] in castor oil or with castor oil vehicle alone. We studied body weight and age at vaginal opening, estrous cycles, and pituitary hormone release in vivo and in vitro, as well as gonadotropin-releasing hormone (GnRH) pulsatility at PND13 and in adults. We also analyzed two GnRH-activated signaling pathways in the adults: inositol-triphosphate (IP3), and extracellular signal-regulated kinase1/2 (ERK1/2). Results Exposure to BPA altered pituitary function in infantile rats, lowering basal and GnRH-induced luteinizing hormone (LH) and increasing GnRH pulsatility. BPA dose-dependently accelerated puberty onset and altered estrous cyclicity, with the high dose causing permanent estrus. In adults treated neonatally with BPA, GnRH-induced LH secretion in vivo was decreased and GnRH pulsatility remained disrupted. In vitro, pituitary cells from animals treated with BPA showed lower basal LH and dose-dependently affected GnRH-induced IP3 formation; the high dose also impaired GnRH-induced LH secretion. Both doses altered ERK1/2 activation. Conclusions Neonatal exposure to BPA altered reproductive parameters and hypothalamic–pituitary function in female rats. To our knowledge, these results demonstrate for the first time that neonatal in vivo BPA permanently affects GnRH pulsatility and pituitary GnRH signaling. PMID:19479018

Phosphorylation of bacterial-type phosphoenolpyruvate carboxylase at Ser425 provides a further tier of enzyme control in developing castor oil seeds.

PubMed

O'Leary, Brendan; Rao, Srinath K; Plaxton, William C

2011-01-01

PEPC [PEP (phosphoenolpyruvate) carboxylase] is a tightly controlled anaplerotic enzyme situated at a pivotal branch point of plant carbohydrate metabolism. Two distinct oligomeric PEPC classes were discovered in developing COS (castor oil seeds). Class-1 PEPC is a typical homotetramer of 107 kDa PTPC (plant-type PEPC) subunits, whereas the novel 910-kDa Class-2 PEPC hetero-octamer arises from a tight interaction between Class-1 PEPC and 118 kDa BTPC (bacterial-type PEPC) subunits. Mass spectrometric analysis of immunopurified COS BTPC indicated that it is subject to in vivo proline-directed phosphorylation at Ser425. We show that immunoblots probed with phosphorylation site-specific antibodies demonstrated that Ser425 phosphorylation is promoted during COS development, becoming maximal at stage IX (maturation phase) or in response to depodding. Kinetic analyses of a recombinant, chimaeric Class-2 PEPC containing phosphomimetic BTPC mutant subunits (S425D) indicated that Ser425 phosphorylation results in significant BTPC inhibition by: (i) increasing its Km(PEP) 3-fold, (ii) reducing its I50 (L-malate and L-aspartate) values by 4.5- and 2.5-fold respectively, while (iii) decreasing its activity within the physiological pH range. The developmental pattern and kinetic influence of Ser425 BTPC phosphorylation is very distinct from the in vivo phosphorylation/activation of COS Class-1 PEPC's PTPC subunits at Ser11. Collectively, the results establish that BTPC's phospho-Ser425 content depends upon COS developmental and physiological status and that Ser425 phosphorylation attenuates the catalytic activity of BTPC subunits within a Class-2 PEPC complex. To the best of our knowledge, this study provides the first evidence for protein phosphorylation as a mechanism for the in vivo control of vascular plant BTPC activity.

Toxic and repellent activity of selected monoterpenoids (thymol, carvacrol and linalool) against the castor bean tick, Ixodes ricinus (Acari: Ixodidae).

PubMed

Tabari, Mohaddeseh Abouhosseini; Youssefi, Mohammad Reza; Maggi, Filippo; Benelli, Giovanni

2017-10-15

The castor bean tick, Ixodes ricinus, is a species of medical and veterinary importance. The use of synthetic acaricides for tick control has led to development of resistance, residues in the environment and animal products, and public health concerns. In this regard, plant essential oils and their main constituents represent an appealing alternative strategy to combat ticks. The phenols thymol and carvacrol and the alcohol linalool are monoterpenoids occurring in essential oils of several aromatic and medicinal plants, such as thyme, oregano, savory, lavender and coriander. Recent studies have shown toxicity of these monoterpenoids against selected mosquito vectors and other arthropod pests. However, information on their bioactivity on I. ricinus is not available. On this basis, here we evaluated the ovicidal, larvicidal and repellency effects of these compounds against I. ricinus. Concentrations of 0.25, 0.5, 1, 2 and 5% were sprayed on the egg masses, then hatching rates were noted. Larvicidal assays were conducted on unengorged larvae, following the larval packet technique. The repellency was determined by measuring the vertical migration behavior of ticks in laboratory conditions. Carvacrol and thymol at all concentrations tested led to a significant hatching decrease, showing an efficacy higher than permethrin, whereas linalool did not cause any significant effect. In the larvae treated with carvacrol and thymol (1, 2 and 5%), mortality rates reached 100% after 24h, showing a larvicidal efficacy higher than permethrin, whereas no effect was seen in the larval groups treated with linalool. Carvacrol and thymol at all concentrations tested showed >90% repellency on I. ricinus. Linalool was scarcely effective (50.24% repellency) only at the concentration of 5%. Overall, based on these results, the phenols carvacrol and thymol can be considered as candidate ingredients for the development of novel acaricidal formulations to control the populations of I. ricinus and the spread of related tick-borne diseases. Copyright © 2017 Elsevier B.V. All rights reserved.

A dynamic pressure view cell for acoustic stimulation of fluids--Micro-bubble generation and fluid movement in porous media.

PubMed

Stewart, Robert A; Shaw, J M

2015-09-01

The development and baseline operation of an acoustic view cell for observing fluids, and fluid-fluid and fluid-solid interfaces in porous media over the frequency range of 10-5000 Hz is described. This range includes the industrially relevant frequency range 500-5000 Hz that is not covered by existing devices. Pressure waveforms of arbitrary shape are generated in a 17.46 mm ID by 200 mm and 690.5 mm long glass tubes at flow rates up to 200 ml/min using a syringe pump. Peak-to-peak amplitudes exceeding 80 kPa are readily realized at frequencies from 10 to 5000 Hz in bubble free fluids when actuated with 20 Vpp as exemplified using castor oil. At resonant frequencies, peak-to-peak pressure amplitudes exceeding 500 kPa were obtained (castor oil at 2100 Hz when actuated with 20 Vpp). Impacts of vibration on macroscopic liquid-liquid and liquid-vapour interfaces and interface movement are illustrated. Pressure wave transmission and attenuation in a fluid saturated porous medium, randomly packed 250-330 μm spherical silica beads, is also demonstrated. Attenuation differences and frequency shifts in resonant peaks are used to detect the presence and generation of dispersed micro-bubbles (<180 μm diameter), and bubbles within porous media that are not readily visualized. Envisioned applications include assessment of the impacts of vibration on reaction, mass transfer, and flow/flow pattern outcomes. This knowledge will inform laboratory and pilot scale process studies, where nuisance vibrations may affect the interpretation of process outcomes, and large scale or in situ processes in aquifers or hydrocarbon reservoirs where imposed vibration may be deployed to improve aspects of process performance. Future work will include miscible interface observation and quantitative measurements in the bulk and in porous media where the roles of micro-bubbles comprise subjects of special interest.

Process for hydrocracking carbonaceous material in liquid carrier

DOEpatents

Duncan, Dennis A.

1980-01-01

Solid carbonaceous material is hydrocracked to provide aliphatic and aromatic hydrocarbons for use as gaseous and liquid fuels or chemical feed stock. Particulate carbonaceous material such as coal in slurry with recycled product oil is preheated in liquid state to a temperature of 600.degree.-1200.degree. F. in the presence of hydrogen gas. The product oil acts as a sorbing agent for the agglomerating bitumins to minimize caking within the process. In the hydrocracking reactor, the slurry of oil and carbonaceous particles is heated within a tubular passageway to vaporize the oil and form a gas-solid mixture which is further heated to a hydropyrolysis temperature in excess of 1200.degree. F. The gas-solid mixture is quenched by contact with additional oil to condense normally liquid hydrocarbons for separation from the gases. A fraction of the hydrocarbon liquid product is recycled for quenching and slurrying with the carbonaceous feed. Hydrogen is recovered from the gas for recycle and additional hydrogen is produced by gasification of residual char.

Preparation of the Pt/CNTs Catalyst and Its Application to the Fabrication of Hydrogenated Soybean Oil Containing a Low Content of Trans Fatty Acids Using the Solid Polymer Electrolyte Reactor.

PubMed

Zheng, Huanyu; Ding, Yangyue; Xu, Hui; Zhang, Lin; Cui, Yueting; Han, Jianchun; Zhu, Xiuqing; Yu, Dianyu; Jiang, Lianzhou; Liu, Lilai

2018-08-01

Pt/CNTs were synthesized with an ethylene glycol reduction method, and the effects of carboxyl functionalization, ultrasonic power and the concentration of chloroplatinic acid on the catalytic activity of Pt/CNTs were investigated. The optimal performance of the Pt/CNTs catalyst was obtained when the ultrasonic power was 300 W and the concentration of chloroplatinic acid was 40 mg/mL. The durability and stability of the Pt/CNTs catalyst were considerably better compared to Pt/C, as shown by cyclic voltammetry measurement results. The trans fatty acids content of the obtained hydrogenated soybean oil (IV: 108.4 gl2/100 g oil) using Pt/CNTs as the cathode catalyst in a solid polymer electrolyte reactor was only 1.49%. The IV of hydrogenated soybean oil obtained using CNTs as carrier with Pt loading 0.1 mg/cm2 (IV: 108.4 gl2/100 g oil) was lower than carbon with a Pt loading of 0.8 mg/cm2 (IV: 109.9 gl2/100 g oil). Thus, to achive the same IV, the usage of Pt was much less when carbon nanotubes were selected as catalyst carrier compared to traditional carbon carrier. The changes of fatty acid components and the hydrogenated selectivity of octadecenoic acid were also discussed.

Thermal stability of some aircraft turbine fuels derived from oil shale and coal

NASA Technical Reports Server (NTRS)

Reynolds, T. W.

1977-01-01

Thermal stability breakpoint temperatures are shown for 32 jet fuels prepared from oil shale and coal syncrudes by various degrees of hydrogenation. Low severity hydrotreated shale oils, with nitrogen contents of 0.1 to 0.24 weight percent, had breakpoint temperatures in the 477 to 505 K (400 to 450 F) range. Higher severity treatment, lowering nitrogen levels to 0.008 to 0.017 weight percent, resulted in breakpoint temperatures in the 505 to 533 K (450 to 500 F) range. Coal derived fuels showed generally increasing breakpoint temperatures with increasing weight percent hydrogen, fuels below 13 weight percent hydrogen having breakpoints below 533 K (500 F). Comparisons are shown with similar literature data.

STABILIZATION OF BIO-OIL TO ENABLE ITS HYDROTREATING TO PRODUCE BIOFUELS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Huamin

Fast pyrolysis is considered to be the simplest and most cost-effective approach to produce liquid oil (bio-oil) from biomass. Bio-oil is not suitable to substitute for petroleum as high-quality fuels and significant upgrading such as hydrotreating is required to remove oxygen, add hydrogen, and rearrange carbon backbone of bio-oil. However, the grand challenge in bio-oil hydrotreating technology is bio-oil instability, which limits the lifetime of catalyst and operation. To enable a sustainable and economically viable process for bio-oil hydrotreating, it is vital to develop effective technologies for stabilizing bio-oils. This chapter will be devoted to bio-oil stabilization. The current understatingmore » of the major cause of bio-oil instability, condensation of reactive species such as sugar, aldehydes, ketones, and phenolics, is elucidated. The reported physical and chemical methods for bio-oil stabilization are summarized in detail, with a specific focus on bio-oil catalytic hydrogenation for stabilization. The impact of stabilization on bio-oil hydrotreating is discussed as well.« less

Castor bean allergy in the upholstery department of a furniture factory.

PubMed Central

Topping, M D; Tyrer, F H; Lowing, R K

1981-01-01

In this study, undertaken to identify the cause of allergy in several upholstery workers in a furniture factory, the workers were handling several different materials, including glue, silicone spray, upholstery fabrics, and felt. Radio-allergo-sorbent test (RAST) assays showed that sera from sensitised workers contained specific IgE towards the felt; however, further investigations using RAST showed that the allergen was not the felt itself but a contaminant of the felt. The felt was manufactured from sacks, some of which had been used to store castor beans. The sera with raised IgE to the felt also had raised IgE to the castor bean extract. By means of RAST inhibition we confirmed that castor bean allergens in the felt were solely responsible for the raised IgE in the sera. The in-vitro RAST results were found to correlate well with the in-vivo pick tests and clinical symptoms. PMID:7272244

Liquid fuel generation from algal biomass via a two-step process: effect of feedstocks.

PubMed

Xu, Yu-Ping; Duan, Pei-Gao; Wang, Feng; Guan, Qing-Qing

2018-01-01

In this study, a two-step processing method (hydrothermal liquefaction followed by catalytic upgrading) was used to produce upgraded bio-oil. A comprehensive screening analysis of algal species, including four microalgae and four macroalgae, was conducted to bridge the gap between previous accounts of microalgae and macroalgae hydrothermal liquefaction and the upgrading process of the resulting crude bio-oils. Hydrothermal liquefaction using eight algal biomasses was performed at 350 °C for 1 h. The microalgae always produced a higher crude bio-oil yield than the macroalgae due to their high lipid content, among which Schizochytrium limacinum provided the maximum crude bio-oil yield of 54.42 wt%. For microalgae, higher amounts of N in the biomass resulted in higher amounts of N in the crude bio-oil; however, contrary results were observed for the macroalgae. The crude bio-oils generated from both the microalgae and macroalgae were characterized as having a high viscosity, total acid number, and heteroatom content, and they were influenced by the biochemical compositions of the feedstocks. Next, all eight-crude bio-oils were treated at 400 °C for 2 h with 10 wt% Ru/C using tetralin as the hydrogen donor. The hydrogen source was provided after tetralin was transformed to naphthalene. All the upgraded bio-oils had higher energy densities and significantly lower N, O, and S contents and viscosities than their corresponding crude bio-oils. However, the H/C molar ratio of the upgraded bio-oils decreased due to the absence of external hydrogen relative to the crude bio-oils. The S content of the upgraded bio-oil produced from upgrading the Schizochytrium limacinum crude bio-oil was even close to the 50 ppm requirement of China IV diesel. Microalgae are better feedstocks than macroalgae for liquid fuel production. Biochemical components have a significant impact on the yield and composition of crude bio-oil. Tetralin does not perform as well as external hydrogen for controlling coke formation. The S content of the upgraded bio-oil can be reduced to 76 ppm for the crude bio-oil produced from Schizochytrium limacinum . Upgraded bio-oils have similar properties to those of naphtha and jet fuel.

Photonic crystal fiber modal interferometer with Pd/WO3 coating for real-time monitoring of dissolved hydrogen concentration in transformer oil

NASA Astrophysics Data System (ADS)

Zhang, Ya-nan; Wu, Qilu; Peng, Huijie; Zhao, Yong

2016-12-01

A highly-sensitive and temperature-robust photonic crystal fiber (PCF) modal interferometer coated with Pd/WO3 film was fabricated and studied, aiming for real-time monitoring of dissolved hydrogen concentration in transformer oil. The sensor probe was fabricated by splicing two segments of a single mode fiber (SMF) with both ends of the PCF. Since the collapse of air holes in the PCF in the interfaces between SMF and PCF, a SMF-PCF-SMF interferometer structure was formed. The Pd/WO3 film was fabricated by sol-gel method and coated on the surface of the PCF by dip-coating method. When the Pd/WO3 film is exposed to hydrogen, both the length and cladding refractive index of the PCF would be changed, resulting in the resonant wavelength shift of the interferometer. Experimental results showed that the hydrogen measurement sensitivity of the proposed sensor can reach 0.109 pm/(μl/l) in the transformer oil, with the measurement range of 0-10 000 μl/l and response time less than 33 min. Besides, the proposed sensor was temperature-insensitive without any compensation process, easy to fabricate without any tapering, polishing, or etching process, low cost and quickly response without any oil-gas separation device. All these performances satisfy the actual need of real-time monitoring of dissolved hydrogen concentration in the transformer oil.

Photonic crystal fiber modal interferometer with Pd/WO3 coating for real-time monitoring of dissolved hydrogen concentration in transformer oil.

PubMed

Zhang, Ya-Nan; Wu, Qilu; Peng, Huijie; Zhao, Yong

2016-12-01

A highly-sensitive and temperature-robust photonic crystal fiber (PCF) modal interferometer coated with Pd/WO 3 film was fabricated and studied, aiming for real-time monitoring of dissolved hydrogen concentration in transformer oil. The sensor probe was fabricated by splicing two segments of a single mode fiber (SMF) with both ends of the PCF. Since the collapse of air holes in the PCF in the interfaces between SMF and PCF, a SMF-PCF-SMF interferometer structure was formed. The Pd/WO 3 film was fabricated by sol-gel method and coated on the surface of the PCF by dip-coating method. When the Pd/WO 3 film is exposed to hydrogen, both the length and cladding refractive index of the PCF would be changed, resulting in the resonant wavelength shift of the interferometer. Experimental results showed that the hydrogen measurement sensitivity of the proposed sensor can reach 0.109 pm/(μl/l) in the transformer oil, with the measurement range of 0-10 000 μl/l and response time less than 33 min. Besides, the proposed sensor was temperature-insensitive without any compensation process, easy to fabricate without any tapering, polishing, or etching process, low cost and quickly response without any oil-gas separation device. All these performances satisfy the actual need of real-time monitoring of dissolved hydrogen concentration in the transformer oil.

Methods and apparatuses for deoxygenating pyrolysis oil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baird, Lance Awender; Brandvold, Timothy A.; Frey, Stanley Joseph

Methods and apparatuses are provided for deoxygenating pyrolysis oil. A method includes contacting a pyrolysis oil with a deoxygenation catalyst in a first reactor at deoxygenation conditions to produce a first reactor effluent. The first reactor effluent has a first oxygen concentration and a first hydrogen concentration, based on hydrocarbons in the first reactor effluent, and the first reactor effluent includes an aromatic compound. The first reactor effluent is contacted with a dehydrogenation catalyst in a second reactor at conditions that deoxygenate the first reactor effluent while preserving the aromatic compound to produce a second reactor effluent. The second reactormore » effluent has a second oxygen concentration lower than the first oxygen concentration and a second hydrogen concentration that is equal to or lower than the first hydrogen concentration, where the second oxygen concentration and the second hydrogen concentration are based on the hydrocarbons in the second reactor effluent.« less

Bitumen and heavy oil upgrading in Canada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chrones, J.; Germain, R.R.

1989-01-01

A review is presented of the heavy oil upgrading industry in Canada. Up to now it has been based on the processing of bitumen extracted from oil sands mining operations at two sites, to produce a residue-free, low sulphur, synthetic crude. Carbon rejection has been the prime process technology with delayed coking being used by Suncor and FLUID COKING at Syncrude. Alternative processes for recovering greater amounts of synthetic crude are examined. These include a variety of hydrogen addition processes and combinations which produce pipelineable materials requiring further processing in downstream refineries with expanded capabilities. The Newgrade Energy Inc. upgradermore » now under construction in Regina, will use fixed-bed, catalytic, atmospheric-residue, hydrogen processing. Two additional projects, also based on hydrogenation, will use ebullated bed catalyst systems; the expansion of Syncrude, now underway, is using the LC Fining Process whereas the announced Husky Bi-Provincial upgrader is based on H-Oil.« less

Bitumen and heavy oil upgrading in Canada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chrones, J.

1988-06-01

A review is presented of the heavy oil upgrading industry in Canada. Up to now it has been based on the processing of bitumen extracted from oil sands mining operations at two sites, to produce a residue-free, low sulfur, synthetic crude. Carbon rejection has been the prime process technology with delayed coking being used by Suncor and FLUID COKING at Syncrude. Alternative processes for recovering greater amounts of synthetic crude are examined. These include a variety of hydrogen addition processes and combinations which produce pipelineable materials requiring further processing in downstream refineries with expanded capabilities. The Newgrade Energy Inc. upgrader,more » now under construction in Regina, will use fixed-bed, catalytic, atmospheric-residue, hydrogen processing. Two additional products, also based on hydrogenation, will use ebullated bed catalyst systems: the expansion of Syncrude, now underway, is using the LC Fining Process whereas the announced Husky Bi-Provincial upgrader is based on H-Oil.« less

Noble metal catalyzed aqueous phase hydrogenation and hydrodeoxygenation of lignin-derived pyrolysis oil and related model compounds.

PubMed

Mu, Wei; Ben, Haoxi; Du, Xiaotang; Zhang, Xiaodan; Hu, Fan; Liu, Wei; Ragauskas, Arthur J; Deng, Yulin

2014-12-01

Aqueous phase hydrodeoxygenation of lignin pyrolysis oil and related model compounds were investigated using four noble metals supported on activated carbon. The hydrodeoxygenation of guaiacol has three major reaction pathways and the demethylation reaction, mainly catalyzed by Pd, Pt and Rh, produces catechol as the products. The presence of catechol and guaiacol in the reaction is responsible for the coke formation and the catalysts deactivation. As expected, there was a significant decrease in the specific surface area of Pd, Pt and Rh catalysts during the catalytic reaction because of the coke deposition. In contrast, no catechol was produced from guaiacol when Ru was used so a completely hydrogenation was accomplished. The lignin pyrolysis oil upgrading with Pt and Ru catalysts further validated the reaction mechanism deduced from model compounds. Fully hydrogenated bio-oil was produced with Ru catalyst. Copyright © 2014 Elsevier Ltd. All rights reserved.

Determination of trace nickel in hydrogenated cottonseed oil by electrothermal atomic absorption spectrometry after microwave-assisted digestion.

PubMed

Zhang, Gai

2012-01-01

Microwave digestion of hydrogenated cottonseed oil prior to trace nickel determination by electrothermal atomic absorption spectrometry (ETAAS) is proposed here for the first time. Currently, the methods outlined in U.S. Pharmacopeia 28 (USP28) or British Pharmacopeia (BP2003) are recommended as the official methods for analyzing nickel in hydrogenated cottonseed oil. With these methods the samples may be pre-treated by a silica or a platinum crucible. However, the samples were easily tarnished during sample pretreatment when using a silica crucible. In contrast, when using a platinum crucible, hydrogenated cottonseed oil acting as a reducing material may react with the platinum and destroy the crucible. The proposed microwave-assisted digestion avoided tarnishing of sample in the process of sample pretreatment and also reduced the cycle of analysis. The programs of microwave digestion and the parameters of ETAAS were optimized. The accuracy of the proposed method was investigated by analyzing real samples. The results were compared with the ones by pressurized-PTFE-bomb acid digestion and ones obtained by the U.S. Pharmacopeia 28 (USP28) method. The new method involves a relatively rapid matrix destruction technique compared with other present methods for the quantification of metals in oil. © 2011 Institute of Food Technologists®

Chemical composition and cytotoxicity evaluation of essential oil from leaves of Casearia sylvestris, its main compound α-zingiberene and derivatives.

PubMed

Bou, Diego Dinis; Lago, João Henrique G; Figueiredo, Carlos R; Matsuo, Alisson L; Guadagnin, Rafael C; Soares, Marisi G; Sartorelli, Patricia

2013-08-08

Casearia sylvestris (Salicaceae), popularly known as "guaçatonga", is a plant widely used in folk medicine to treat various diseases, including cancer. The present work deals with the chemical composition as well as the cytotoxic evaluation of its essential oil, its main constituent and derivatives. Thus, the crude essential oil from leaves of C. sylvestris was obtained using a Clevenger type apparatus and analyzed by GC/MS. This analysis afforded the identification of 23 substances, 13 of which corresponded to 98.73% of the total oil composition, with sesquiterpene a-zingiberene accounting for 50% of the oil. The essential oil was evaluated for cytotoxic activity against several tumor cell lines, giving IC50 values ranging from 12 to 153 mg/mL. Pure a-zingiberene, isolated from essential oil, was also evaluated against the tumor cell lines showing activity for HeLa, U-87, Siha and HL60 cell lines, but with IC50 values higher than those determined for the crude essential oil. Aiming to evaluate the effect of the double bonds of a-zingiberene on the cytotoxic activity, partially hydrogenated a-zingiberene (PHZ) and fully hydrogenated a-zingiberene (THZ) derivatives were obtained. For the partially hydrogenated derivative only cytotoxic activity to the B16F10-Nex2 cell line (IC50 65 mg/mL) was detected, while totally hydrogenated derivative showed cytotoxic activity for almost all cell lines, with B16F10-Nex2 and MCF-7 as exceptions and with IC50 values ranging from 34 to 65 mg/mL. These results indicate that cytotoxic activity is related with the state of oxidation of compound.

21 CFR 73.3110 - Chlorophyllin-copper complex, oil soluble.

Code of Federal Regulations, 2010 CFR

2010-04-01

... oil, peanut oil, and hydrogenated peanut oil), may be safely used to color polymethylmethacrylate bone... the bone cement. (2) Authorization for this use shall not be construed as waiving any of the... the polymethylmethacrylate bone cement in which chlorophyllin-copper complex, oil soluble, is used. (d...

21 CFR 73.3110 - Chlorophyllin-copper complex, oil soluble.

Code of Federal Regulations, 2013 CFR

2013-04-01

... oil, peanut oil, and hydrogenated peanut oil), may be safely used to color polymethylmethacrylate bone... the bone cement. (2) Authorization for this use shall not be construed as waiving any of the... the polymethylmethacrylate bone cement in which chlorophyllin-copper complex, oil soluble, is used. (d...

21 CFR 73.3110 - Chlorophyllin-copper complex, oil soluble.

Code of Federal Regulations, 2014 CFR

2014-04-01

... oil, peanut oil, and hydrogenated peanut oil), may be safely used to color polymethylmethacrylate bone... the bone cement. (2) Authorization for this use shall not be construed as waiving any of the... the polymethylmethacrylate bone cement in which chlorophyllin-copper complex, oil soluble, is used. (d...

21 CFR 73.3110 - Chlorophyllin-copper complex, oil soluble.

Code of Federal Regulations, 2012 CFR

2012-04-01

... oil, peanut oil, and hydrogenated peanut oil), may be safely used to color polymethylmethacrylate bone... the bone cement. (2) Authorization for this use shall not be construed as waiving any of the... the polymethylmethacrylate bone cement in which chlorophyllin-copper complex, oil soluble, is used. (d...

21 CFR 73.3110 - Chlorophyllin-copper complex, oil soluble.

Code of Federal Regulations, 2011 CFR

2011-04-01

... oil, peanut oil, and hydrogenated peanut oil), may be safely used to color polymethylmethacrylate bone... the bone cement. (2) Authorization for this use shall not be construed as waiving any of the... the polymethylmethacrylate bone cement in which chlorophyllin-copper complex, oil soluble, is used. (d...

Electrosorption of organic acids from aqueous bio-oil and conversion into hydrogen via microbial electrolysis cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, Lydia Kyoung-Eun; Satinover, Scott J.; Yiacoumi, Sotira

Neutralization of the bio-oil pH has been shown to generate a neutralized bio-oil aqueous phase (NBOAP) that includes most of the acidic components and a neutralized bio-oil organic phase (NBOOP) that includes hydrophobic organics, such as phenols. NBOOP can be used for fuel production, while NBOAP can be fed to microbial electrolysis cells (MECs) for hydrogen production. After pH neutralization, some organic acidic components remain in NBOOP. This work is focused on capturing acidic compounds from NBOOP through water extraction and electrosorption, and demonstrating hydrogen production via MECs. Capacitive deionization (CDI) is proven effective in capturing ions from NBOOP-contacted watermore » and NBOAP via electrosorption. Captured acidic compounds enable the MEC application to effectively produce renewable hydrogen. Chemical oxygen demand (COD) removal of 49.2%, 61.5%, and 60.8% for 2, 4, and 10 g/L-anode/day loading were observed, corresponding to a total COD degradation of 0.19 g/L, 0.79 g/L, and 1.3 g/L, respectively. A maximum hydrogen productivity of 4.3 L-H 2/L-anode/day was obtained. Major compounds in the water phase such as fatty acids, sugar derivatives, furanic and phenolic compounds were converted to hydrogen with an efficiency of 80–90%. Lastly, this approach may lead the entire biomass pyrolysis process to be an overall carbon-neutral process.« less

Electrosorption of organic acids from aqueous bio-oil and conversion into hydrogen via microbial electrolysis cells

DOE PAGES

Park, Lydia Kyoung-Eun; Satinover, Scott J.; Yiacoumi, Sotira; ...

2018-02-17

Neutralization of the bio-oil pH has been shown to generate a neutralized bio-oil aqueous phase (NBOAP) that includes most of the acidic components and a neutralized bio-oil organic phase (NBOOP) that includes hydrophobic organics, such as phenols. NBOOP can be used for fuel production, while NBOAP can be fed to microbial electrolysis cells (MECs) for hydrogen production. After pH neutralization, some organic acidic components remain in NBOOP. This work is focused on capturing acidic compounds from NBOOP through water extraction and electrosorption, and demonstrating hydrogen production via MECs. Capacitive deionization (CDI) is proven effective in capturing ions from NBOOP-contacted watermore » and NBOAP via electrosorption. Captured acidic compounds enable the MEC application to effectively produce renewable hydrogen. Chemical oxygen demand (COD) removal of 49.2%, 61.5%, and 60.8% for 2, 4, and 10 g/L-anode/day loading were observed, corresponding to a total COD degradation of 0.19 g/L, 0.79 g/L, and 1.3 g/L, respectively. A maximum hydrogen productivity of 4.3 L-H 2/L-anode/day was obtained. Major compounds in the water phase such as fatty acids, sugar derivatives, furanic and phenolic compounds were converted to hydrogen with an efficiency of 80–90%. Lastly, this approach may lead the entire biomass pyrolysis process to be an overall carbon-neutral process.« less

Natural wax organogels for cookies

USDA-ARS?s Scientific Manuscript database

Organogels formed from vegetable oil and an organogelator have drawn great interest as alternatives to trans fats. Unlike the current alternatives to trans fats such as tropical oils, fully hydrogenated oils and their transesterifed oils containing high contents of saturated fats, organogels can be ...

Storage stability of cooked sausages containing vegetable oils.

PubMed

Papavergou, E J; Ambrosiadis, J A; Psomas, J

1995-01-01

Comminuted cooked sausages were produced using standard industrial practices, by substituting corn oil, sunflower oil, cotton seed oil, soybean oil and hydrogenated vegetable fat for animal fat. When processed, products were assessed for their stability with respect to autoxidation and change in organoleptic properties during vacuum-packed storage in a domestic refrigerator at 4 degrees C. Data obtained indicated that changes in thiobarbituric acid (TBA) values and organoleptic properties of products produced using corn oil, sunflower oil and hydrogenated vegetable fat were similar to those observed for reference material produced using lard. In the case of samples produced using soybean and cotton seed oil, TBA value changes were more pronounced, but did not exceed acceptable limits. A more rapid deterioration of organoleptic characteristics was also observed for the same samples, which showed flavour problems after 3 months of storage at 4 degrees C. Substitution of plant oils for lard considerably reduced the cholesterol content and increased the ratio of unsaturated to saturated fatty acids of cooked sausages.

Hydrogenated cottonseed oil as raw material for biobased materials

USDA-ARS?s Scientific Manuscript database

There has been a lot of recent interest in using vegetable oils as biodegradable and renewable raw materials for the syntheses of various biobased materials. Although most of the attention has been paid to soybean oil thus far, cottonseed oil is a viable alternative. An advantage of cottonseed oil...

In situ generation of steam and alkaline surfactant for enhanced oil recovery using an exothermic water reactant (EWR)

DOEpatents

Robertson, Eric P

2011-05-24

A method for oil recovery whereby an exothermic water reactant (EWR) encapsulated in a water soluble coating is placed in water and pumped into one or more oil wells in contact with an oil bearing formation. After the water carries the EWR to the bottom of the injection well, the water soluble coating dissolves and the EWR reacts with the water to produce heat, an alkali solution, and hydrogen. The heat from the EWR reaction generates steam, which is forced into the oil bearing formation where it condenses and transfers heat to the oil, elevating its temperature and decreasing the viscosity of the oil. The aqueous alkali solution mixes with the oil in the oil bearing formation and forms a surfactant that reduces the interfacial tension between the oil and water. The hydrogen may be used to react with the oil at these elevated temperatures to form lighter molecules, thus upgrading to a certain extent the oil in situ. As a result, the oil can flow more efficiently and easily through the oil bearing formation towards and into one or more production wells.

Materials towards carbon-free, emission-free and oil-free mobility: hydrogen fuel-cell vehicles--now and in the future.

PubMed

Hirose, Katsuhiko

2010-07-28

In the past, material innovation has changed society through new material-induced technologies, adding a new value to society. In the present world, engineers and scientists are expected to invent new materials to solve the global problem of climate change. For the transport sector, the challenge for material engineers is to change the oil-based world into a sustainable world. After witnessing the recent high oil price and its adverse impact on the global economy, it is time to accelerate our efforts towards this change. Industries are tackling global energy issues such as oil and CO2, as well as local environmental problems, such as NO(x) and particulate matter. Hydrogen is the most promising candidate to provide carbon-free, emission-free and oil-free mobility. As such, engineers are working very hard to bring this technology into the real society. This paper describes recent progress of vehicle technologies, as well as hydrogen-storage technologies to extend the cruise range and ensure the easiness of refuelling and requesting material scientists to collaborate with industry to fight against global warming.

Hydrogen as an Auxiliary Fuel in Compression-Ignition Engines

NASA Technical Reports Server (NTRS)

Gerrish, Harold C; Foster, H

1936-01-01

An investigation was made to determine whether a sufficient amount of hydrogen could be efficiently burned in a compression-ignition engine to compensate for the increase of lift of an airship due to the consumption of the fuel oil. The performance of a single-cylinder four-stroke-cycle compression-ignition engine operating on fuel oil alone was compared with its performance when various quantities of hydrogen were inducted with the inlet air. Engine-performance data, indicator cards, and exhaust-gas samples were obtained for each change in engine-operating conditions.

Sulfur-Tolerant Molybdenum Carbide Catalysts Enabling Low-Temperature Stabilization of Fast Pyrolysis Bio-oil

DOE PAGES

Li, Zhenglong; Choi, Jae-Soon; Wang, Huamin; ...

2017-08-18

Low-temperature hydrogenation of carbonyl fractions can greatly improve the thermal stability of fast pyrolysis bio-oil which is crucial to achieve long-term operation of high-temperature upgrading reactors. The current state of the art, precious metals such as ruthenium, although highly effective in carbonyl hydrogenation, rapidly loses performance due to sulfur sensitivity. The present work showed that molybdenum carbides were active and sulfur-tolerant in low-temperature conversion carbonyl compounds. Furthermore, due to surface bifunctionality (presence of both metallic and acid sites), carbides catalyzed both C=O bond hydrogenation and C-C coupling reactions retaining most of carbon atoms in liquid products as more stable andmore » higher molecular weight oligomeric compounds while consuming less hydrogen than ruthenium. The carbides proved to be resistant to other deactivation mechanisms including hydrothermal aging, oxidation, coking and leaching. These properties enabled carbides to achieve and maintain good catalytic performance in both aqueous-phase furfural conversion and real bio-oil stabilization with sulfur present. This finding strongly suggests that molybdenum carbides can provide a catalyst solution necessary for the development of commercially viable bio-oil stabilization technology.« less

Sulfur-Tolerant Molybdenum Carbide Catalysts Enabling Low-Temperature Stabilization of Fast Pyrolysis Bio-oil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Zhenglong; Choi, Jae-Soon; Wang, Huamin

Low-temperature hydrogenation of carbonyl fractions can greatly improve the thermal stability of fast pyrolysis bio-oil which is crucial to achieve long-term operation of high-temperature upgrading reactors. The current state of the art, precious metals such as ruthenium, although highly effective in carbonyl hydrogenation, rapidly loses performance due to sulfur sensitivity. The present work showed that molybdenum carbides were active and sulfur-tolerant in low-temperature conversion carbonyl compounds. Furthermore, due to surface bifunctionality (presence of both metallic and acid sites), carbides catalyzed both C=O bond hydrogenation and C-C coupling reactions retaining most of carbon atoms in liquid products as more stable andmore » higher molecular weight oligomeric compounds while consuming less hydrogen than ruthenium. The carbides proved to be resistant to other deactivation mechanisms including hydrothermal aging, oxidation, coking and leaching. These properties enabled carbides to achieve and maintain good catalytic performance in both aqueous-phase furfural conversion and real bio-oil stabilization with sulfur present. This finding strongly suggests that molybdenum carbides can provide a catalyst solution necessary for the development of commercially viable bio-oil stabilization technology.« less

Influence of the Oil Phase and Topical Formulation on the Wound Healing Ability of a Birch Bark Dry Extract

PubMed Central

Steinbrenner, Isabel; Houdek, Pia; Pollok, Simone; Brandner, Johanna M.; Daniels, Rolf

2016-01-01

Triterpenes from the outer bark of birch are known for various pharmacological effects including enhanced wound healing (WH). A birch bark dry extract (TE) obtained by accelerated solvent extraction showed the ability to form oleogels when it is suspended in oils. Consistency of the oleogels and the dissolved amount of triterpenes varies largely with the used oil. Here we wanted to know to what extent different oils and formulations (oleogel versus o/w emulsion) influence WH. Looking at the plain oils, medium-chain triglycerides (MCT) enhanced WH (ca. 1.4-fold), while e.g. castor oil (ca.0.3-fold) or light liquid paraffin (LLP; ca. 0.5-fold) significantly decreased WH. Concerning the respective oleogels, TE-MCT showed no improvement although the solubility of the TE was high. In contrast, the oleogel of sunflower oil which alone showed a slight tendency to impair WH, enhanced WH significantly (ca. 1.6-fold). These results can be explained by release experiments where the release rate of betulin, the main component of TE, from MCT oleogels was significantly lower than from sunflower oil oleogels. LLP impaired WH as plain oil and even though it released betulin comparable to sunflower oil it still results in an overall negative effect of the oleogel on WH. As a further formulation option also surfactant free o/w emulsions were prepared using MCT, sunflower oil and LLP as a nonpolar oil phase. Depending on the preparation method (suspension or oleogel method) the distribution of the TE varied markedly and affected also release kinetics. However, the released betulin was clearly below the values measured with the respective oleogels. Consequently, none of the emulsions showed a significantly positive effect on WH. In conclusion, our data show that the oil used as a vehicle influences wound healing not only by affecting the release of the extract, but also by having its own vehicle effect on wound healing. This is also of importance for other applications where drugs have to be applied in non-polar vehicles because these solvents likely influence the outcome of the experiment substantially. PMID:27219110

Properties of oleogels formed with high-stearic soybean oils and sunflower wax

USDA-ARS?s Scientific Manuscript database

In an effort to develop alternatives for harmful trans fats produced by hydrogenation of vegetable oils, oleogels of high stearic soybean (A6 and MM106) oils were prepared with sunflower wax as oleogelator. Oleogels of high stearic oils did not have greater firmness than that of regular soybean oil ...

Alternative Fuels Data Center: Hydrogenation-Derived Renewable Diesel

Science.gov Websites

rapeseed oil; animal tallow; vegetable oil waste or brown trap grease; and other fats and vegetable oils new pipelines, storage tanks, or retail station pumps), can be produced using existing oil refinery manufacturers-including ConocoPhillips, Neste Oil, Petrobras, REG, and UOP-are developing and testing HDRD

Mit castor satellite: Design, implementation, and testing of the communication system

NASA Astrophysics Data System (ADS)

Babuscia, Alessandra; McCormack, Matthew Michael; Munoz, Michael; Parra, Spencer; Miller, David W.

2012-12-01

Cathode Anode Satellite Thruster for Orbital Reposition (CASTOR) is an orbital manoeuvre and transfer micro-satellite bus developed at MIT Space System Laboratory. The technical objective of the mission is achieving 1 km/s of delta-V over a 1 year mission in Low Earth Orbit (LEO). This will be accomplished using a novel electric propulsion system, the Diverging Cusped Field Thruster (DCFT), which enables high efficiency orbital changes of the ESPA-ring class satellite. CASTOR is capable of improving rapid access to space capabilities by providing an orbital transfer platform with a very high performance to mass ratio, thus greatly reducing launch costs and allowing for highly efficient orbital manoeuvre. Furthermore, CASTOR is highly scalable and modular, allowing it to be adapted to a wide range of scales and applications. CASTOR is developed as part of the University Nanosatellite Program (UNP) funded by Air Force Research Laboratory (AFRL). In order to accomplish CASTOR mission objective, a highly optimized, scalable, light weight, and low cost communication system needed to be developed. These constraints imply the development of trade studies to select the final communication system architecture able to maximize the amount of data transmitted, while guaranteeing reliability, redundancy and limited mass, power consumption, and cost. A special attention is also required to guarantee a reliable communication system in cases of tumbling, or in case of strong Doppler shift which is inevitable due to the high delta-V capabilities of the vehicle. In order to accomplish all the mission requirements, different features have been introduced in the design of the communication system for this mission. Specifically, customized patch antennas have been realized, and a customized communication protocol has been designed and implemented. The communication subsystem has been validated through an intense testing campaign which included software tests in the laboratory, hardware tests in anechoic chamber, and in flight tests through a balloon experiment. The article presents an overview of CASTOR mission, a presentation of the trade studies analysis and of the final communication architecture selected, a description of the customized antenna developed, of the customized protocol designed, and a presentation of the results of the tests performed.

21 CFR 173.275 - Hydrogenated sperm oil.

Code of Federal Regulations, 2014 CFR

2014-04-01

... from rendering the fatty tissue of the sperm whale or is prepared by synthesis of fatty acids and fatty alcohols derived from the sperm whale. The sperm oil obtained by rendering is refined. The oil is...

Effect of conducting core on the dynamics of a compound drop in an AC electric field

NASA Astrophysics Data System (ADS)

Soni, Purushottam; Dixit, Divya; Juvekar, Vinay A.

2017-11-01

Dynamics of 0.1M NaCl/castor oil/silicone oil compound drop in an alternating electric field of frequency 1 Hz was investigated experimentally in a parallel plate electrode cell. A novel yet simple method was used for producing the compound drop with different ratios of the core radius to shell radius. Deformation dynamics under both transient and cyclical steady states were recorded using high-speed imaging. We observed that with an increase in the radius ratio, deformation of the shell increases and that of the core decreases. The temporal deformation of the core always leads that of the shell. The phase lead between the core and the shell is independent of electric field strength and salt concentration in the core but strongly depends on the viscosity of the medium and radius ratio. At a small radius ratio, the breakup of the core is similar to the disintegration of the isolated drop in an infinite fluid; whereas the core attends a diamond-like shape at a high radius ratio before ejecting the small droplets from the tips.

Characterization and evaluation of an oral microemulsion containing the antitumor diterpenoid compound ent-11alpha-hydroxy-15-oxo-kaur-16-en-19-oic-acid.

PubMed

Lu, Yingnian; Wu, Kefeng; Li, Li; He, Yuhui; Cui, Liao; Liang, Nianci; Mu, Bozhong

2013-01-01

The objective of this study was to develop an oral microemulsion formulation of the antitumor diterpenoid agent, ent-11α-hydroxy-15-oxo-kaur-16-en-19-oic-acid (henceforth referred to as 5F), to enhance its bioavailability and evaluate its hepatotoxicity. Pseudoternary phase diagrams showed that the optimal microemulsion formulation contained 45% water, 10% castor oil as the oil phase, 15% Cremophor EL as the surfactant, and 30% as a cosurfactant mixture of 1,2-propanediol and polyethylene glycol (PEG)-400 (2:1, w/w). The microemulsion preparation was characterized and its droplet diameter was within 50 nm. Release of 5F in vitro from the microemulsion was slightly increased compared with a suspension containing the same amount of active drug. Pharmacokinetic parameters in vivo indicated that bioavailability was markedly improved, with the relative bioavailability being 616.15% higher for the microemulsion than for the suspension. Toxicity tests showed that the microemulsion had no hepatotoxicity in mice. These results suggest the potential for 5F microemulsion to be administered by the oral route.

Novel Fluorescent Microemulsion: Probing Properties, Investigating Mechanism, and Unveiling Potential Application.

PubMed

Hou, Mengna; Dang, Leping; Liu, Tiankuo; Guo, Yun; Wang, Zhanzhong

2017-08-09

Nanoscale microemulsions have been utilized as delivery carriers for nutraceuticals and active biological drugs. Herein, we designed and synthesized a novel oil in water (O/W) fluorescent microemulsion based on isoamyl acetate, polyoxyethylene castor oil EL (CrEL), and water. The microemulsion emitted bright blue fluorescence, thus exhibiting its potential for active drug detection with label-free strategy. The microemulsion exhibited excitation-dependent emission and distinct red shift with longer excitation wavelengths. Lifetime and quantum yield of fluorescent microemulsion were 2.831 ns and 5.0%, respectively. An excellent fluorescent stability of the microemulsion was confirmed by altering pH, ionic strength, temperature, and time. Moreover, we proposed a probable mechanism of fluorochromic phenomenon, in connection with the aromatic ring structure of polyoxyethylene ether substituent in CrEL. Based on our findings, we concluded that this new fluorescent microemulsion is a promising drug carrier that can facilitate active drug detection with a label-free strategy. Although further research is required to understand the exact mechanism behind its fluorescence property, this work provided valuable guidance to develop new biosensors based on fluorescent microemulsion.

7 CFR 810.1404 - Grades and grade requirements for sorghum.

Code of Federal Regulations, 2011 CFR

2011-01-01

... material: Animal filth 9 9 9 9 Castor beans 1 1 1 1 Crotalaria seeds 2 2 2 2 Glass 1 1 1 1 Stones 2 7 7 7 7... animal filth, castor beans, crotalaria seeds, glass, stones, unknown foreign substance or cockleburs. [72...

7 CFR 810.1404 - Grades and grade requirements for sorghum.

Code of Federal Regulations, 2012 CFR

2012-01-01

... material: Animal filth 9 9 9 9 Castor beans 1 1 1 1 Crotalaria seeds 2 2 2 2 Glass 1 1 1 1 Stones 2 7 7 7 7... animal filth, castor beans, crotalaria seeds, glass, stones, unknown foreign substance or cockleburs. [72...

7 CFR 810.1404 - Grades and grade requirements for sorghum.

Code of Federal Regulations, 2013 CFR

2013-01-01

... material: Animal filth 9 9 9 9 Castor beans 1 1 1 1 Crotalaria seeds 2 2 2 2 Glass 1 1 1 1 Stones 2 7 7 7 7... animal filth, castor beans, crotalaria seeds, glass, stones, unknown foreign substance or cockleburs. [72...

7 CFR 810.1404 - Grades and grade requirements for sorghum.

Code of Federal Regulations, 2014 CFR

2014-01-01

... material: Animal filth 9 9 9 9 Castor beans 1 1 1 1 Crotalaria seeds 2 2 2 2 Glass 1 1 1 1 Stones 2 7 7 7 7... animal filth, castor beans, crotalaria seeds, glass, stones, unknown foreign substance or cockleburs. [72...

7 CFR 810.1404 - Grades and grade requirements for sorghum.

Code of Federal Regulations, 2010 CFR

2010-01-01

... material: Animal filth 9 9 9 9 Castor beans 1 1 1 1 Crotalaria seeds 2 2 2 2 Glass 1 1 1 1 Stones 2 7 7 7 7... animal filth, castor beans, crotalaria seeds, glass, stones, unknown foreign substance or cockleburs. [72...

30 CFR 250.808 - Hydrogen sulfide.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 2 2013-07-01 2013-07-01 false Hydrogen sulfide. 250.808 Section 250.808 Mineral Resources BUREAU OF SAFETY AND ENVIRONMENTAL ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL... § 250.808 Hydrogen sulfide. Production operations in zones known to contain hydrogen sulfide (H2S) or in...

30 CFR 250.808 - Hydrogen sulfide.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 2 2014-07-01 2014-07-01 false Hydrogen sulfide. 250.808 Section 250.808 Mineral Resources BUREAU OF SAFETY AND ENVIRONMENTAL ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL... § 250.808 Hydrogen sulfide. Production operations in zones known to contain hydrogen sulfide (H2S) or in...

30 CFR 250.808 - Hydrogen sulfide.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 2 2012-07-01 2012-07-01 false Hydrogen sulfide. 250.808 Section 250.808 Mineral Resources BUREAU OF SAFETY AND ENVIRONMENTAL ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL... § 250.808 Hydrogen sulfide. Production operations in zones known to contain hydrogen sulfide (H2S) or in...

In Vitro Activity of Copper(II) Complexes, Loaded or Unloaded into a Nanostructured Lipid System, against Mycobacterium tuberculosis.

PubMed

Silva, Patricia B da; Souza, Paula C de; Calixto, Giovana Maria Fioramonti; Lopes, Erica de O; Frem, Regina C G; Netto, Adelino V G; Mauro, Antonio E; Pavan, Fernando R; Chorilli, Marlus

2016-05-17

Tuberculosis (TB) is an infectious disease caused mainly by the bacillus Mycobacterium tuberculosis (Mtb), presenting 9.5 million new cases and 1.5 million deaths in 2014. The aim of this study was to evaluate a nanostructured lipid system (NLS) composed of 10% phase oil (cholesterol), 10% surfactant (soy phosphatidylcholine, sodium oleate), and Eumulgin(®) HRE 40 ([castor oil polyoxyl-40-hydrogenated] in a proportion of 3:6:8), and an 80% aqueous phase (phosphate buffer pH = 7.4) as a tactic to enhance the in vitro anti-Mtb activity of the copper(II) complexes [CuCl₂(INH)₂]·H₂O (1), [Cu(NCS)₂(INH)₂]·5H₂O (2) and [Cu(NCO)₂(INH)₂]·4H₂O (3). The Cu(II) complex-loaded NLS displayed sizes ranging from 169.5 ± 0.7095 to 211.1 ± 0.8963 nm, polydispersity index (PDI) varying from 0.135 ± 0.0130 to 0.236 ± 0.00100, and zeta potential ranging from -0.00690 ± 0.0896 to -8.43 ± 1.63 mV. Rheological analysis showed that the formulations behave as non-Newtonian fluids of the pseudoplastic and viscoelastic type. Antimycobacterial activities of the free complexes and NLS-loaded complexes against Mtb H37Rv ATCC 27294 were evaluated by the REMA methodology, and the selectivity index (SI) was calculated using the cytotoxicity index (IC50) against Vero (ATCC(®) CCL-81), J774A.1 (ATCC(®) TIB-67), and MRC-5 (ATCC(®) CCL-171) cell lines. The data suggest that the incorporation of the complexes into NLS improved the inhibitory action against Mtb by 52-, 27-, and 4.7-fold and the SI values by 173-, 43-, and 7-fold for the compounds 1, 2 and 3, respectively. The incorporation of the complexes 1, 2 and 3 into the NLS also resulted in a significant decrease of toxicity towards an alternative model (Artemia salina L.). These findings suggest that the NLS may be considered as a platform for incorporation of metallic complexes aimed at the treatment of TB.

Techno-economic and resource analysis of hydroprocessed renewable jet fuel

DOE PAGES

Tao, Ling; Milbrandt, Anelia; Zhang, Yanan; ...

2017-11-09

Biomass-derived jet fuel is an alternative jet fuel (AJF) showing promise of reducing the dependence on fossil fuel and greenhouse gas emissions. Hydroprocessed esters and fatty acids (HEFA) concept is also known as one of the pathways for producing bio jet fuel. HEFA fuel was approved by the American Society for Testing and Materials in 2011, and can be blended up to 50% with conventional jet fuel. Since then, several HEFA economic and life-cycle assessments have been published in literature. However, there have been limited analyses on feedstock availability, composition, and their impact on hydrocarbon yield (particularly jet blendstock yield)more » and overall process economics. Our study examines over 20 oil feedstocks, their geographic distribution and production levels, oil yield, prices, and chemical composition. The results of our compositional analysis, thus, indicate that most oils contain mainly C16 and C18 fatty acids except pennycress, yellow grease, and mustard, which contain higher values and thus would require hydrocracking to improve jet fuel production. Coconut oil has a large content of shorter carbon fatty acids, making it a good feedstock candidate for renewable gasoline instead of jet substitutes' production. Techno-economic analysis (TEA) was performed for five selected oil feedstocks - camelina, pennycress, jatropha, castor bean, and yellow grease - using the HEFA process concept. The resource analysis indicates that oil crops currently grown in the United States (namely soybean) have relatively low oil yield when compared to oil crops grown in other parts of the world, such as palm, coconut, and jatropha. Also, non-terrestrial oil sources, such as animal fats and greases, have relatively lower prices than terrestrial oil crops. The minimum jet fuel selling price for these five resources ranges between $3.8 and $11.0 per gallon. The results of our TEA and resource studies indicate the key cost drivers for a biorefinery converting oil to jet hydrocarbons are as follows: oil price, conversion plant capacity, fatty acid profile, addition of hydrocracker, and type of hydroprocessing catalysts.« less

Techno-economic and resource analysis of hydroprocessed renewable jet fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tao, Ling; Milbrandt, Anelia; Zhang, Yanan

Biomass-derived jet fuel is an alternative jet fuel (AJF) showing promise of reducing the dependence on fossil fuel and greenhouse gas emissions. Hydroprocessed esters and fatty acids (HEFA) concept is also known as one of the pathways for producing bio jet fuel. HEFA fuel was approved by the American Society for Testing and Materials in 2011, and can be blended up to 50% with conventional jet fuel. Since then, several HEFA economic and life-cycle assessments have been published in literature. However, there have been limited analyses on feedstock availability, composition, and their impact on hydrocarbon yield (particularly jet blendstock yield)more » and overall process economics. Our study examines over 20 oil feedstocks, their geographic distribution and production levels, oil yield, prices, and chemical composition. The results of our compositional analysis, thus, indicate that most oils contain mainly C16 and C18 fatty acids except pennycress, yellow grease, and mustard, which contain higher values and thus would require hydrocracking to improve jet fuel production. Coconut oil has a large content of shorter carbon fatty acids, making it a good feedstock candidate for renewable gasoline instead of jet substitutes' production. Techno-economic analysis (TEA) was performed for five selected oil feedstocks - camelina, pennycress, jatropha, castor bean, and yellow grease - using the HEFA process concept. The resource analysis indicates that oil crops currently grown in the United States (namely soybean) have relatively low oil yield when compared to oil crops grown in other parts of the world, such as palm, coconut, and jatropha. Also, non-terrestrial oil sources, such as animal fats and greases, have relatively lower prices than terrestrial oil crops. The minimum jet fuel selling price for these five resources ranges between $3.8 and $11.0 per gallon. The results of our TEA and resource studies indicate the key cost drivers for a biorefinery converting oil to jet hydrocarbons are as follows: oil price, conversion plant capacity, fatty acid profile, addition of hydrocracker, and type of hydroprocessing catalysts.« less

21 CFR 173.275 - Hydrogenated sperm oil.

Code of Federal Regulations, 2010 CFR

2010-04-01

... conditions: (a) The sperm oil is derived from rendering the fatty tissue of the sperm whale or is prepared by synthesis of fatty acids and fatty alcohols derived from the sperm whale. The sperm oil obtained by...

21 CFR 173.275 - Hydrogenated sperm oil.

Code of Federal Regulations, 2013 CFR

2013-04-01

... conditions: (a) The sperm oil is derived from rendering the fatty tissue of the sperm whale or is prepared by synthesis of fatty acids and fatty alcohols derived from the sperm whale. The sperm oil obtained by...

21 CFR 173.275 - Hydrogenated sperm oil.

Code of Federal Regulations, 2012 CFR

2012-04-01

... conditions: (a) The sperm oil is derived from rendering the fatty tissue of the sperm whale or is prepared by synthesis of fatty acids and fatty alcohols derived from the sperm whale. The sperm oil obtained by...

21 CFR 173.275 - Hydrogenated sperm oil.

Code of Federal Regulations, 2011 CFR

2011-04-01

... conditions: (a) The sperm oil is derived from rendering the fatty tissue of the sperm whale or is prepared by synthesis of fatty acids and fatty alcohols derived from the sperm whale. The sperm oil obtained by...

Co-liquefaction of Elbistan Lignite with Manure Biomass; Part 2 - Effect of Biomass Type, Waste to Lignite Ratio and Solid to Liquid Ratio

NASA Astrophysics Data System (ADS)

Karaca, Hüseyin; Koyunoglu, Cemil

2017-12-01

Most coal hydrogenation processes require a large quantity of hydrogen. In general, a coal derived liquid such as anthracene oil was used as a hydrogen donor solvent. Tetralin, partially hydrogenated pyrene, phenantrene and coal-derived solvents, which contain hydroaromatic compounds, are efficient solvents to donate hydrogen. In an attempt to reduce the high cost of hydrogen, part of the hydrogen was replaced by a low cost hydrogen donor solvent. This must be hydrogenated during or before the process and recycled. To reduce the cost of hydrogen donor vehicles instead of liquids recycled from the liquefaction process or several biomass types, industrial by products, liquid fractions derived from oil sands bitumen were successfully used to solubilize a coal from the past. In an attempt to reduce the high cost of hydrogen, part of the hydrogen was replaced by a low cost hydrogen donor solvent. However, when hydrogen is supplied from the hydroaromatic structures present in the solvent, the activity of coal minerals is too low to rehydrogenate the solvent in-situ. Nevertheless, a decrease of using oxygen, in addition to enhanced usage of the hydrogen supply by using various waste materials might lead to a decrease of the cost of the liquefaction procedure. So instead of using tetralin another feeding material such as biomass is becoming another solution improving hydrogen donor substances. Most of the liquefaction process were carried out in a batch reactor, in which the residence time of the liquefaction products is long enough to favour the retrogressive reactions, early studies which are related to liquefaction of coal with biomass generally focus on the synergetic effects of coal while biomass added. Early studies which are related to liquefaction of coal with biomass generally focus on the synergetic effects of coal while biomass added. Alternatively, to understand the hydrogen transfer from biomass to coal, in this study, Elbistan Lignite (EL) with manure, tea pulp and waste plastic liquefied and to understand hydrogen quantity change after liquefaction, (H/C)atomic ratio of products obtained. Due to the highest oil conversion of manure biomass and highest (H/C)atomic ratio results show manure is the favourable biomass for EL amongst the other biomass used. And liquid/solid ratio optimized. About high total conversion of oil products the optimum ratio obtained as 3/1. And also EL with manure liquefied with the w/EL ratio between 0:1 to 1:1. As a result, by thinking about the yield values obtained, the optimum waste to lignite ratio found to be 1:1.

The trouble with hydrogen fuel cells

NASA Astrophysics Data System (ADS)

Clar, Robert

2010-03-01

The article "Kicking the oil addiction" (January pp22-26) presented an interesting picture of a future in which most cars are powered by hydrogen fuel cells. However, the article underestimated several peculiarities of hydrogen production, storage, distribution and safety.

Effect of pretreating of host oil on coprocessing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hajdu, P.E.; Tierney, J.W.; Wender, I.

1995-12-31

The principal objective of this research was to determine if coprocessing performance (i.e., coal conversion and oil yield) could be significantly improved by pretreating the heavy resid prior to reacting it with coal. For this purpose, two petroleum vacuum resids (1000{degrees}F+), one from the Amoco Co. and another from the Citgo Co., were used as such and after they had been pretreated by catalytic hydrogenation and hydrocracking reactions. The pretreatments were aimed at improving the host oil by; (1) converting any aromatic structures in the petroleum to hydroaromatic compounds capable of donating hydrogen, (2) cracking the heavy oil to lowermore » molecular weight material that might serve as a better solvent, (3) reducing the coking propensity of the heavy oil through the hydrogenation of polynuclear aromatic compounds, and (4) removing metals and heteroatoms that might poison a coprocessing catalyst. Highly dispersed catalysts, including fine particle Fe- and Mo-based, and dicobalt octacarbonyl, Co{sub 2}(CO){sub 8}, were used in this study. The untreated and pretreated resids were extensively characterized in order to determine chemical changes brought about by the pretreatments. The modified heavy oils were then coprocessed with an Illinois No. 6 coal as well as with a Wyodak coal, and compared to coprocessing with untreated resids under the same hydroliquefaction conditions. The amount of oil derived from coal was estimated by measuring the level of phenolic oxygen (derived mainly from coal) present in the oil products. Results are presented and discussed.« less

AMC’s Hydrogen Future: Sustainable Air Mobility

DTIC Science & Technology

2009-06-01

by bacteria . The Orinoco heavy oil has been degraded less than the Canadian oil sands making it easier to extract. The Orinoco oil contains 300...molecules tend to evaporate. Bacteria at the surface modify the oil leaving ring compounds. This causes the oil to become more viscous than conventional...267 billion barrels recoverable (Mommer, 2004). The difference between the oil sands and heavy oil is the degree to which the oil has been degraded

Analysis of castor by ELISAs that distinguish Ricin and Ricinus communis agglutinin (RCA)

USDA-ARS?s Scientific Manuscript database

To facilitate the analysis of castor (Ricinus communis L.) seed fractions and germplasm for ricin content, we investigated the use of enzyme-linked immunosorbent assay (ELISA) methods to differentiate between ricin toxin and the related Ricinus communis agglutinin (RCA). Both proteins are based on ...

10 CFR 72.214 - List of approved spent fuel storage casks.

Code of Federal Regulations, 2012 CFR

2012-01-01

... specified in their Certificates of Compliance. Certificate Number: 1000 SAR Submitted by: General Nuclear Systems, Inc. SAR Title: Topical Safety Analysis Report for the Castor V/21 Cask Independent Spent Fuel... Model Number: CASTOR V/21 Certificate Number: 1002 SAR Submitted by: Nuclear Assurance Corporation SAR...

10 CFR 72.214 - List of approved spent fuel storage casks.

Code of Federal Regulations, 2014 CFR

2014-01-01

... specified in their Certificates of Compliance. Certificate Number: 1000 SAR Submitted by: General Nuclear Systems, Inc. SAR Title: Topical Safety Analysis Report for the Castor V/21 Cask Independent Spent Fuel... Model Number: CASTOR V/21 Certificate Number: 1002 SAR Submitted by: Nuclear Assurance Corporation SAR...

10 CFR 72.214 - List of approved spent fuel storage casks.

Code of Federal Regulations, 2013 CFR

2013-01-01

... specified in their Certificates of Compliance. Certificate Number: 1000 SAR Submitted by: General Nuclear Systems, Inc. SAR Title: Topical Safety Analysis Report for the Castor V/21 Cask Independent Spent Fuel... Model Number: CASTOR V/21 Certificate Number: 1002 SAR Submitted by: Nuclear Assurance Corporation SAR...

Effect of Gradual Heating and Fat/Oil Type on Fat Stability, Texture, Color, and Microstructure of Meat Batters.

PubMed

Barbut, S; Youssef, M K

2016-09-01

The effects of endpoint cooking temperature (40, 50, 60, 70, 80, and 90 °C) on emulsion stability, texture, color, and microstructure of meat batters prepared with different fats/oils were studied. Canola oil treatments showed the highest cooking loss whereas hydrogenated palm oil provided the most stable meat batters. Rendered beef fat was less stable than regular beef fat. Increasing endpoint cooking temperatures resulted in a progressive reduction of water holding capacity in all treatments. As temperature was raised, meat batters showed higher hardness and cohesiveness values, but no appreciable changes in cohesiveness above 60 °C. Canola and hydrogenated palm oil treatments showed the highest hardness and chewiness values. Lightness (L(*) ) values of all meat batters increased significantly with increasing temperature from 40 to 60 or 70 °C; no major changes observed above 70 °C. Light microscopy revealed no substantial changes in the microstructure of all the stable meat batters cooked to between 50 and 70 °C. Heating to 90 °C changed the microstructure in all meat batters except the hydrogenated palm oil treatments, which still showed nonround fat particles and a less aggregated protein matrix. © 2016 Institute of Food Technologists®

Optimization of biodiesel supply chains based on small farmers: a case study in Brazil.

PubMed

Leão, Raphael Riemke de Campos Cesar; Hamacher, Silvio; Oliveira, Fabrício

2011-10-01

This article presents a methodology for conceiving and planning the development of an optimized supply chain of a biodiesel plant sourced from family farms and taking into consideration agricultural, logistic, industrial, and social aspects. This model was successfully applied to the production chain of biodiesel fuel from castor oil in the semi-arid region of Brazil. Results suggest important insights related to the optimal configuration of the crushing units, regarding its location, technology, and when it should be available, as well as the configuration of the production zones along the planning horizon considered. Moreover, a sensitivity analysis is performed in order to measure how possible variations in the considered conjecture can affect the robustness of the solutions. Copyright © 2011 Elsevier Ltd. All rights reserved.

Diversity of plant oil seed-associated fungi isolated from seven oil-bearing seeds and their potential for the production of lipolytic enzymes.

PubMed

Venkatesagowda, Balaji; Ponugupaty, Ebenezer; Barbosa, Aneli M; Dekker, Robert F H

2012-01-01

Commercial oil-yielding seeds (castor, coconut, neem, peanut, pongamia, rubber and sesame) were collected from different places in the state of Tamil Nadu (India) from which 1279 endophytic fungi were isolated. The oil-bearing seeds exhibited rich fungal diversity. High Shannon-Index H' was observed with pongamia seeds (2.847) while a low Index occurred for coconut kernel-associated mycoflora (1.018). Maximum Colonization Frequency (%) was observed for Lasiodiplodia theobromae (176). Dominance Index (expressed in terms of the Simpson's Index D) was high (0.581) for coconut kernel-associated fungi, and low for pongamia seed-borne fungi. Species Richness (Chao) of the fungal isolates was high (47.09) in the case of neem seeds, and low (16.6) for peanut seeds. All 1279 fungal isolates were screened for lipolytic activity employing a zymogram method using Tween-20 in agar. Forty isolates showed strong lipolytic activity, and were morphologically identified as belonging to 19 taxa (Alternaria, Aspergillus, Chalaropsis, Cladosporium, Colletotrichum, Curvularia, Drechslera, Fusarium, Lasiodiplodia, Mucor, Penicillium, Pestalotiopsis, Phoma, Phomopsis, Phyllosticta, Rhizopus, Sclerotinia, Stachybotrys and Trichoderma). These isolates also exhibited amylolytic, proteolytic and cellulolytic activities. Five fungal isolates (Aspergillus niger, Chalaropsis thielavioides, Colletotrichum gloeosporioides, Lasiodiplodia theobromae and Phoma glomerata) exhibited highest lipase activities, and the best producer was Lasiodiplodia theobromae (108 U/mL), which was characterized by genomic sequence analysis of the ITS region of 18S rDNA.

One-step preparation of biological aviation kerosene by catalytic hydrogenation of waste lard over Pt/SAPO-11

NASA Astrophysics Data System (ADS)

Zhang, X.; Chen, Y. B.; Li, X. Y.; Souliyathai, D.; Zhang, S. P.; Wang, Q.; Liu, Q.; Du, J. C.; Zhang, A. M.

2017-11-01

Biological aviation kerosene was produced by one-step catalytic hydrotreatment of waste lard oil over Pt/SAPO-11 in a high-pressure fixed bed micro reactor. The influence of reaction conditions such as temperature, pressure, hydrogen oil ratio, and space velocity on the deoxygenation rate, the selectivity of C8-C16 hydrocarbons and the isomerization rate of C8-C16 hydrocarbons have been investigated. The experimental results showed that the temperature of 400°C, pressure of 5 MPa, hydrogen oil ratio of 1000 and space velocity of 1.2 h-1 were the best experimental reaction conditions. Under these conditions, the conversion rate is 96.62%, the selectivity of C8-C16 hydrocarbons is 50.25%, and the isomerization rate of C8-C16 hydrocarbons is 35.68%.

30 CFR 250.808 - Hydrogen sulfide.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Hydrogen sulfide. 250.808 Section 250.808... OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Production Safety Systems § 250.808 Hydrogen sulfide. Production operations in zones known to contain hydrogen sulfide (H2S) or in zones where the presence of H2S...

30 CFR 250.504 - Hydrogen sulfide.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Hydrogen sulfide. 250.504 Section 250.504... OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Well-Completion Operations § 250.504 Hydrogen sulfide. When a well-completion operation is conducted in zones known to contain hydrogen sulfide (H2S) or in...

30 CFR 250.604 - Hydrogen sulfide.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Hydrogen sulfide. 250.604 Section 250.604... OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Well-Workover Operations § 250.604 Hydrogen sulfide. When a well-workover operation is conducted in zones known to contain hydrogen sulfide (H2S) or in...

Catalytic biorefining of plant biomass to non-pyrolytic lignin bio-oil and carbohydrates through hydrogen transfer reactions.

PubMed

Ferrini, Paola; Rinaldi, Roberto

2014-08-11

Through catalytic hydrogen transfer reactions, a new biorefining method results in the isolation of depolymerized lignin--a non-pyrolytic lignin bio-oil--in addition to pulps that are amenable to enzymatic hydrolysis. Compared with organosolv lignin, the lignin bio-oil is highly susceptible to further hydrodeoxygenation under low-severity conditions and therefore establishes a unique platform for lignin valorization by heterogeneous catalysis. Overall, the potential of a catalytic biorefining method designed from the perspective of lignin utilization is reported. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Utilizing biotechnology in producing fats and oils with various nutritional properties.

PubMed

Flickinger, Brent D

2007-01-01

The role of dietary fat in health and wellness continues to evolve. In today's environment, trans fatty acids and obesity are issues that are impacted by dietary fat. In response to new information in these areas, changes in the amount and composition of edible fats and oils have occurred and are occurring. These compositional changes include variation in fatty acid composition and innovation in fat structure. Soybean, canola, and sunflower are examples of oilseeds with varied fatty acid composition, including mid-oleic, high-oleic, and low-linolenic traits. These trait-enhanced oils are aimed to displace partially hydrogenated vegetable oils primarily in frying applications. Examples of oils with innovation in fat structure include enzyme interesterified (EIE) fats and oils and diacylglycerol oil. EIE fats are a commercial edible fat innovation, where a lipase is used to modify the fat structure of a blend of hard fat and liquid oil. EIE fats are aimed to displace partially hydrogenated vegetable oils in baking and spread applications. Diacylglycerol and medium-chain triglyceride (MCT)-based oils are commercial edible oil innovations. Diacylglycerol and MCT-based oils are aimed for individuals looking to store less of these fats as body fat when they are used in place of traditional cooking and salad oils.

Inhibition of acetoclastic methanogenesis in crude oil- and creosote-contaminated groundwater

USGS Publications Warehouse

Warren, E.; Bekins, B.A.; Godsy, E.M.; Smith, V.K.

2004-01-01

Results from a series of studies of methanogenic processes in crude oil- and creosote-contaminated aquifers indicated that acetoctastic methanogenesis is inhibited near non-aqueous sources. Acetoclastic methanogenesis was more susceptible to the toxic inhibition of crude oil and creosote than either hydrogen- or formate-utilizing methanogenesis. The effect of this toxic inhibition was apparent in the population of the methanogenic trophic groups near nonaqueous crude oil at the Bemidji, MN, site. At that site, acetoclastic methanogens were < 2/g within or near the oil where hydrogen- and formate-utilizing methanogens were 10-100/g. The geochemical effect of this toxic inhibition was the buildup of low molecular weight volatile acids, particularly acetate. Wastewater reactor studies indicated that this toxicity will result in a decrease in the biodegradation rate of contaminants at sites where toxic compounds are present.

Early plasma exchange for treating ricin toxicity in children after castor bean ingestion.

PubMed

Wang, Cheng-feng; Nie, Xiao-jing; Chen, Guang-ming; Yu, Zi-hua; Li, Zheng; Sun, Zhi-wen; Weng, Zeng-feng; Yang, Yu-ying; Chen, Shu-lian; Zheng, Si-rui; Luo, Ying-yun; Lu, Yan-ting; Cao, Hui-qin; Zhan, Hai-xia

2015-06-01

Plasma exchange (PE) for the treatment of ricin toxicity has not been previously reported. Here we describe the use of PE to treat children who experienced ricin toxicity after ingesting castor beans. Seven children (median age: 8.1 years) who consumed castor beans (median: 5 beans) were treated with PE. All had bradycardia and sinus arrhythmia, and most had experienced episodes of vomiting and/or diarrhea. PE settings were blood flow, 50-80 mL/min; PE rate, 600-800 mL/h; volume of exchange, 1440-1950 mL. Median time from ingestion to PE was 73 h. All clinical symptoms disappeared and vital signs rapidly returned to normal after PE; no severe organ dysfunction occurred. All children were discharged and recovered uneventfully. Concentrations of all serum biochemical parameters significantly decreased immediately after PE. Some, but not all, of these parameters were also significantly decreased at 48 and 72 h after PE compared with before PE. Our findings suggest that PE can be an effective early intervention in the treatment of ricin toxicity due to castor bean ingestion. © 2014 Wiley Periodicals, Inc.

Development of rigorous fatty acid near-infrared spectroscopy quantitation methods in support of soybean oil improvement

USDA-ARS?s Scientific Manuscript database

The seed of soybean (Glycine max L. Merr) is a valuable source of high quality edible oil and protein. Despite dramatic breeding gains over the past 80 years, soybean seed oil continues to be oxidatively unstable. Until recently, the majority of soybean oil underwent partial chemical hydrogenation. ...

The Recent Evolution of a Symbiotic Ion Channel in the Legume Family Altered Ion Conductance and Improved Functionality in Calcium Signaling[C][W

PubMed Central

Venkateshwaran, Muthusubramanian; Cosme, Ana; Han, Lu; Banba, Mari; Satyshur, Kenneth A.; Schleiff, Enrico; Parniske, Martin; Imaizumi-Anraku, Haruko; Ané, Jean-Michel

2012-01-01

Arbuscular mycorrhiza and the rhizobia-legume symbiosis are two major root endosymbioses that facilitate plant nutrition. In Lotus japonicus, two symbiotic cation channels, CASTOR and POLLUX, are indispensable for the induction of nuclear calcium spiking, one of the earliest plant responses to symbiotic partner recognition. During recent evolution, a single amino acid substitution in DOES NOT MAKE INFECTIONS1 (DMI1), the POLLUX putative ortholog in the closely related Medicago truncatula, rendered the channel solo sufficient for symbiosis; castor, pollux, and castor pollux double mutants of L. japonicus were rescued by DMI1 alone, while both Lj-CASTOR and Lj-POLLUX were required for rescuing a dmi1 mutant of M. truncatula. Experimental replacement of the critical serine by an alanine in the selectivity filter of Lj-POLLUX conferred a symbiotic performance indistinguishable from DMI1. Electrophysiological characterization of DMI1 and Lj-CASTOR (wild-type and mutants) by planar lipid bilayer experiments combined with calcium imaging in Human Embryonic Kidney-293 cells expressing DMI1 (the wild type and mutants) suggest that the serine-to-alanine substitution conferred reduced conductance with a long open state to DMI1 and improved its efficiency in mediating calcium oscillations. We propose that this single amino acid replacement in the selectivity filter made DMI1 solo sufficient for symbiosis, thus explaining the selective advantage of this allele at the mechanistic level. PMID:22706284

Mechanism of arginine sensing by CASTOR1 upstream of mTORC1

PubMed Central

Saxton, Robert A.; Chantranupong, Lynne; Knockenhauer, Kevin E.; Schwartz, Thomas U.; Sabatini, David M.

2016-01-01

Summary The mechanistic Target of Rapamycin Complex 1 (mTORC1) is a major regulator of eukaryotic growth that coordinates anabolic and catabolic cellular processes with inputs such as growth factors and nutrients, including amino acids1–3. In mammals, arginine is particularly important and promotes diverse physiological effects including immune cell activation, insulin secretion, and muscle growth, largely through activation of mTORC14–7. Arginine activates mTORC1 upstream of the Rag GTPases8, through either the lysosomal amino acid transporter SLC38A9 or the GATOR2-interacting CASTOR1 (Cellular Arginine Sensor for mTORC1)9–12. However, the mechanism by which the mTORC1 pathway detects and transmits the arginine signal has been elusive. Here, we present the 1.8 Å crystal structure of arginine-bound CASTOR1. Homodimeric CASTOR1 binds arginine at the interface of two ACT domains, enabling allosteric control of the adjacent GATOR2-binding site to trigger dissociation from GATOR2 and the downstream activation of mTORC1. Our data reveal that CASTOR1 shares substantial structural homology with the lysine-binding regulatory domain of prokaryotic aspartate kinases, suggesting that the mTORC1 pathway exploited an ancient amino-acid-dependent allosteric mechanism to acquire arginine sensitivity. Together, these results establish a structural basis for arginine sensing by the mTORC1 pathway and provide insights into the evolution of a mammalian nutrient sensor. PMID:27487210

Investigation of surfactant/cosurfactant synergism impact on ibuprofen solubilization capacity and drug release characteristics of nonionic microemulsions.

PubMed

Djekic, Ljiljana; Primorac, Marija; Filipic, Slavica; Agbaba, Danica

2012-08-20

The current study investigates the performances of the multicomponent mixtures of nonionic surfactants regarding the microemulsion stabilisation, drug solubilization and in vitro drug release kinetic. The primary surfactant was PEG-8 caprylic/capric glycerides (Labrasol). The cosurfactants were commercially available mixtures of octoxynol-12 and polysorbate 20 without or with the addition of PEG-40 hydrogenated castor oil (Solubilisant gamma 2421 and Solubilisant gamma 2429, respectively). The oil phase of microemulsions was isopropyl myristate. Phase behaviour study of the pseudo-ternary systems Labrasol/cosurfactant/oil/water at surfactant-to-cosurfactant weight ratios (K(m)) 40:60, 50:50 and 60:40, revealed a strong synergism in the investigated tensides mixtures for stabilisation of microemulsions containing up to 80% (w/w) of water phase at surfactant +cosurfactant-to-oil weight ratio (SCoS/O) 90:10. Solubilization of a model drug ibuprofen in concentration common for topical application (5%, w/w) was achieved at the water contents below 50% (w/w). Drug free and ibuprofen-loaded microemulsions M1-M6, containing 45% (w/w) of water phase, were prepared and characterized by polarized light microscopy, conductivity, pH, rheological and droplet size measurements. In vitro ibuprofen release kinetics from the microemulsions was investigated using paddle-over-enhancer cell method and compared with the commercial 5% (w/w) ibuprofen hydrogel product (Deep Relief, Mentholatum Company Ltd., USA). The investigated microemulsions were isotropic, low viscous Bingham-type liquids with the pH value (4.70-6.61) suitable for topical application. The different efficiency of the tensides mixtures for microemulsion stabilisation was observed, depending on the cosurfactant type and K(m) value. Solubilisant gamma 2429 as well as higher K(m) (i.e., lower relative content of the cosurfactant) provided higher surfactant/cosurfactant synergism. The drug molecules were predominantly solubilized within the interface film. The amount of drug released from the formulations M3 (10.75%, w/w) and M6 (13.45%, w/w) (K(m) 60:40) was limited in comparison with the reference (22.22%, w/w) and follows the Higuchi model. Microemulsions M2 and M5 (K(m) 50:50) gave zero order drug release pattern and ∼15% (w/w) ibuprofen released. The release profiles from microemulsions M1 and M4 (K(m) 40:60) did not fit well with the models used for analysis, although the amounts of ibuprofen released (24.47%, w/w) and 17.99% (w/w), respectively) were comparable to that of the reference hydrogel. The drug release mechanism was related with the surfactant/cosurfactant synergism, thus the lower efficiency of the tensides corresponded to the faster drug release. Copyright © 2012 Elsevier B.V. All rights reserved.

Methods and apparatuses for preparing upgraded pyrolysis oil

DOEpatents

Brandvold, Timothy A; Baird, Lance Awender; Frey, Stanley Joseph

2013-10-01

Methods and apparatuses for preparing upgraded pyrolysis oil are provided herein. In an embodiment, a method of preparing upgraded pyrolysis oil includes providing a biomass-derived pyrolysis oil stream having an original oxygen content. The biomass-derived pyrolysis oil stream is hydrodeoxygenated under catalysis in the presence of hydrogen to form a hydrodeoxygenated pyrolysis oil stream comprising a cyclic paraffin component. At least a portion of the hydrodeoxygenated pyrolysis oil stream is dehydrogenated under catalysis to form the upgraded pyrolysis oil.

Filamentous carbon particles for cleaning oil spills and method of production

DOEpatents

Muradov, Nazim

2010-04-06

A compact hydrogen generator is coupled to or integrated with a fuel cell for portable power applications. Hydrogen is produced via thermocatalytic decomposition (cracking, pyrolysis) of hydrocarbon fuels in oxidant-free environment. The apparatus can utilize a variety of hydrocarbon fuels, including natural gas, propane, gasoline, kerosene, diesel fuel, crude oil (including sulfurous fuels). The hydrogen-rich gas produced is free of carbon oxides or other reactive impurities, so it could be directly fed to any type of a fuel cell. The catalysts for hydrogen production in the apparatus are carbon-based or metal-based materials and doped, if necessary, with a sulfur-capturing agent. Additionally disclosed are two novel processes for the production of two types of carbon filaments, and a novel filamentous carbon product. The hydrogen generator can be conveniently integrated with high temperature fuel cells to produce an efficient and self-contained source of electrical power.

Synthetic fuels for ground transportation with special emphasis on hydrogen

NASA Technical Reports Server (NTRS)

Singh, J. J.

1975-01-01

The role of various synthetic fuels, for ground transportation in the United States, was examined for the near term (by 1985) and the longer term applications (1985-2000 and beyond 2000). Feasible options include synthetic oil, methanol, electric propulsion, and hydrogen. It is concluded that (1) the competition during the next 50 years will be for the fuels of all types, rather than among the fuels; (2) extensive domestic oil and gas exploration should be initiated concurrent with the development of several alternate fuels and related ancillaries; and (3) hydrogen, as an automotive fuel, seems to be equivalent to gasoline for optimum fuel to air mixtures. As a pollution free, high energy density fuel, hydrogen deserves consideration as the logical replacement for the hydrocarbons. Several research and development requirements, essential for the implementation of hydrogen economy for ground transportation, were identified. Extensive engineering development and testing activities should be initiated to establish hydrogen as the future automotive fuel, followed by demonstration projects and concerted efforts at public education.

Anti-diarrhoeal activity of methanol extract of Santalum album L. in mice and gastrointestinal effect on the contraction of isolated jejunum in rats.

PubMed

Guo, Huimin; Zhang, Jingze; Gao, Wenyuan; Qu, Zhuo; Liu, Changxiao

2014-07-03

Santalum album L., namely Sandalwood, honored as "Green Gold", is a traditional Chinese herb which has the effects of anti-diarrhoeal and antibacterial activity. But there is limit scientific study on its activity and mechanism in gastrointestinal disorders. in vivo, after intragastric administration, the methanol extract of Sandalwood (SE) (200, 400 and 800 mg/kg) were studied in castor oil-induced diarrhoea mice. By the test of small intestinal hyperfunction induced by neostigmine, SE was studied on gastrointestinal transit including gastric emptying and small intestinal motility. Meanwhile, in vitro, the effects of SE (0.02, 0.05, 0.1, 0.2, 0.3, 0.4 mg/mL) on the isolated tissue preparations of rat jejunum were also investigated. The rat jejunum strips were pre-contracted with acetylcholine (Ach; 10(-6)M), 5-hydroxytryptamine (5-HT, 200 μM) or potassium chloride (KCl; 60 mM) and tested in the presence of SE. In addition, the possible myogenic effect was analyzed in the pretreatment of the jejunum preparations with SE or verapamil in Ca(2+)-free high-K(+) (60 mM) solution containing EDTA. At doses of 200, 400 and 800 mg/kg, SE showed significant anti-diarrhoeal activity against castor oil-induced diarrhoea as compared with the control. At the same doses, it also inhibited the gastric emptying and small intestinal motility in the mice of which small intestinal hyperfunction induced by neostigmine. It caused inhibitory effects on the spontaneous contraction of rat-isolated jejunum in dose-dependent manner ranging from 0.02 to 0.4 mg/mL, and it also relaxed the Ach-induced, 5-HT-induced and K(+)-induced contractions. SE shifted the Ca(2+) concentration-response curves to right, similar to that caused by verapamil (0.025 mM). These findings indicated that SE played a spasmolytic role in gastrointestinal motility which was probably mediated through inhibition of muscarinic receptors, 5-HT receptors and calcium influx. All these results provide pharmacological basis for its clinical use in gastrointestinal tract. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Antidiarrhoeal and antimicrobial activity of Calpurnia aurea leaf extract.

PubMed

Umer, Shemsu; Tekewe, Alemu; Kebede, Nigatu

2013-01-28

In Ethiopia, Calpurnia aurea is used for the treatment of syphilis, malaria, rabies, diabetes, hypertension, diarrhoea, leishmaniasis, trachoma, elephantiasis, fungal diseases and different swellings. However, despite its traditional usage as an antidiarrhoeal and antimicrobial agent, there is limited or no information regarding its effectiveness and mode of action in diarrhoea which may be caused by Shigella flexneri, Staphylococcus aureus, Escherichia coli and Salmonella typhi. Hence, we evaluated the 80% methanol (MeOH) extract of dried and powdered leaves of C. aurea for its antidiarrhoeal and antimicrobial activities. Swiss albino mice of either sex were divided into five groups (five/group): Group I served as control and received vehicle (1% Tween 80) at a dose of 10 ml/kg orally; Group II served as standard and received loperamide at the dose of 3 mg/kg orally; Groups III, IV and V served as test groups and received the 80% MeOH leaf extract of C. aurea at doses of 100, 200 and 400 mg/kg orally, respectively. Diarrhoea was induced by oral administration of 0.5 ml castor oil to each mouse, 1 h after the above treatments. During an observation period of 4 h, time of onset of diarrhea, total number of faecal output (frequency of defecation) and weight of faeces excreted by the animals were recorded. Data were analyzed using one way analysis of variance followed by Tukey post test. Antimicrobial activity test was conducted using agar well diffusion assay. Clinical isolates tested were Salmonella typhi, Salmonella paratyphi, Salmonella typhimurium, Shigella species, Pseudomonas aeruginosa, Staphylococcus aureus and Escherichia coli. In castor oil induced diarrhea model, the 80% methanol leaf extract of C. aurea at 100, 200 and 400 mg/kg and the standard drug loperamide (3 mg/kg) significantly reduced the time of onset of diarrhea, the frequency of defecation (total number of faecal output) and weight of faeces. C. aurea leaf extract also showed good antimicrobial activity against all tested organisms. C. aurea possesses good antidiarrhoeal and antimicrobial activity which support the traditional use of the plant in the treatment of diarrhea in Ethiopia.

Antidiarrhoeal and antimicrobial activity of Calpurnia aurea leaf extract

PubMed Central

2013-01-01

Background In Ethiopia, Calpurnia aurea is used for the treatment of syphilis, malaria, rabies, diabetes, hypertension, diarrhoea, leishmaniasis, trachoma, elephantiasis, fungal diseases and different swellings. However, despite its traditional usage as an antidiarrhoeal and antimicrobial agent, there is limited or no information regarding its effectiveness and mode of action in diarrhoea which may be caused by Shigella flexneri, Staphylococcus aureus, Escherichia coli and Salmonella typhi. Hence, we evaluated the 80% methanol (MeOH) extract of dried and powdered leaves of C. aurea for its antidiarrhoeal and antimicrobial activities. Methods Swiss albino mice of either sex were divided into five groups (five/group): Group I served as control and received vehicle (1% Tween 80) at a dose of 10 ml/kg orally; Group II served as standard and received loperamide at the dose of 3 mg/kg orally; Groups III, IV and V served as test groups and received the 80% MeOH leaf extract of C. aurea at doses of 100, 200 and 400 mg/kg orally, respectively. Diarrhoea was induced by oral administration of 0.5 ml castor oil to each mouse, 1 h after the above treatments. During an observation period of 4 h, time of onset of diarrhea, total number of faecal output (frequency of defecation) and weight of faeces excreted by the animals were recorded. Data were analyzed using one way analysis of variance followed by Tukey post test. Antimicrobial activity test was conducted using agar well diffusion assay. Clinical isolates tested were Salmonella typhi, Salmonella paratyphi, Salmonella typhimurium, Shigella species, Pseudomonas aeruginosa, Staphylococcus aureus and Escherichia coli. Results In castor oil induced diarrhea model, the 80% methanol leaf extract of C. aurea at 100, 200 and 400 mg/kg and the standard drug loperamide (3 mg/kg) significantly reduced the time of onset of diarrhea, the frequency of defecation (total number of faecal output) and weight of faeces. C. aurea leaf extract also showed good antimicrobial activity against all tested organisms. Conclusions C. aurea possesses good antidiarrhoeal and antimicrobial activity which support the traditional use of the plant in the treatment of diarrhea in Ethiopia. PMID:23351272

DOE Office of Scientific and Technical Information (OSTI.GOV)

Valery, N.

The calorific values of the fuels being studied were compared. Petrol is the most efficient, followed by methane in the form of LGN, then methanol and liquid hydrogen. Hydrogen is attractive only on a weight basis, but the storage problems are serious for its liquefied state. Liquid methane requires the same costly storage equipment as hydrogen, making it prohibitive for road vehicles. Methanol is a clean burning fuel and manufacturing processes are being developed. Tests are being sponsored by the Office of Coal Research and the American Gas Association and large-scale commercial plants could be capable of being onstream bymore » 1978. Synthetic crude oil has been manufactured in Sasol, South Africa since 1955. The technique is based on the Fischer-Tropsch process for synthesizing oil from coal, not only making synthetic petrol from coal but also the full range of products normally derived from crude oil. (MCW)« less

Exergetic life cycle assessment of hydrogen production from renewables

NASA Astrophysics Data System (ADS)

Granovskii, Mikhail; Dincer, Ibrahim; Rosen, Marc A.

Life cycle assessment is extended to exergetic life cycle assessment and used to evaluate the exergy efficiency, economic effectiveness and environmental impact of producing hydrogen using wind and solar energy in place of fossil fuels. The product hydrogen is considered a fuel for fuel cell vehicles and a substitute for gasoline. Fossil fuel technologies for producing hydrogen from natural gas and gasoline from crude oil are contrasted with options using renewable energy. Exergy efficiencies and greenhouse gas and air pollution emissions are evaluated for all process steps, including crude oil and natural gas pipeline transportation, crude oil distillation and natural gas reforming, wind and solar electricity generation, hydrogen production through water electrolysis, and gasoline and hydrogen distribution and utilization. The use of wind power to produce hydrogen via electrolysis, and its application in a fuel cell vehicle, exhibits the lowest fossil and mineral resource consumption rate. However, the economic attractiveness, as measured by a "capital investment effectiveness factor," of renewable technologies depends significantly on the ratio of costs for hydrogen and natural gas. At the present cost ratio of about 2 (per unit of lower heating value or exergy), capital investments are about five times lower to produce hydrogen via natural gas rather than wind energy. As a consequence, the cost of wind- and solar-based electricity and hydrogen is substantially higher than that of natural gas. The implementation of a hydrogen fuel cell instead of an internal combustion engine permits, theoretically, an increase in a vehicle's engine efficiency of about of two times. Depending on the ratio in engine efficiencies, the substitution of gasoline with "renewable" hydrogen leads to (a) greenhouse gas (GHG) emissions reductions of 12-23 times for hydrogen from wind and 5-8 times for hydrogen from solar energy, and (b) air pollution (AP) emissions reductions of 38-76 times for hydrogen from wind and 16-32 times for hydrogen from solar energy. By comparison, substitution of gasoline with hydrogen from natural gas allows reductions in GHG emissions only as a result of the increased efficiency of a fuel cell engine, and a reduction of AP emissions of 2.5-5 times. These data suggest that "renewable" hydrogen represents a potential long-term solution to many environmental problems.

Thermionic cogeneration burner design

NASA Astrophysics Data System (ADS)

Miskolczy, G.; Goodale, D.; Moffat, A. L.; Morgan, D. T.

Since thermionic converters receive heat at very high temperatures (approximately 1800 K) and reject heat at moderately high temperatures (approximately 800 K), they are useful for cogeneration applications involving high temperature processes. The electric power from thermionic converters is produced as a high amperage, low-voltage direct current. An ideal cogeneration application would be to utilize the reject heat at the collector temperature and the electricity without power conditioning. A cogeneration application in the edible oil industry fulfills both of these requirements since both direct heat and hydrogen gas are required in the hydrogenation of the oils. In this application, the low-voltage direct current would be used in a hydrogen electrolyzer.

Process and apparatus for coal hydrogenation

DOEpatents

Ruether, John A.; Simpson, Theodore B.

1991-01-01

In a coal liquefaction process an aqueous slurry of coal is prepared containing a dissolved liquefaction catalyst. A small quantity of oil is added to the slurry and then coal-oil agglomerates are prepared by agitation of the slurry at atmospheric pressure. The resulting mixture is drained of excess water and dried at atmospheric pressure leaving catalyst deposited on the agglomerates. The agglomerates then are fed to an extrusion device where they are formed into a continuous ribbon of extrudate and fed into a hydrogenation reactor at elevated pressure and temperature. The catalytic hydrogenation converts the extrudate primarily to liquid hydrocarbons in the reactor. The liquid drained in recovering the agglomerates is recycled.

Electrochemical Upgrading of Bio-Oil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elangovan, S.; Larsen, Dennis; Bay, Insoo

Bio-oil produced by fast pyrolysis of biomass is a potential source of low carbon, renewable hydrocarbon fuel. However, the properties such as low heating value, incomplete volatility, acidity, instability, and incompatibility with standard fuels restrict its use. The undesirable properties of pyrolysis oil result from its chemical composition that mostly consists of different classes of oxygenated organic compounds. Current process of Hydrodeoxygenation to remove oxygen involves high-temperature, high-pressure processing in the presence of hydrogen and catalyst. An alternative process of deoxygenation of bio-oil using solid-state, oxygen conductor based electrochemical cell is under investigation. The electrolysis process removes oxygen from themore » oxygenated organic molecule as well from steam to produce hydrogen in-situ allowing for a distributed, small scale integrated upgrading unit. Mixtures of model compounds and a slip stream of pyrolysis vapor were tested. The results show the potential for integrating a pyrolyzer and an electrochemical device for stabilizing pyrolysis oil.« less

An Evaluation of the Harbor of Yokosuka, Japan as a Typhoon Haven

DTIC Science & Technology

1975-06-01

following are some pertinent comments by various commands listed in Figure D-4. SHIP CARBONERO (SS337) MEDREGAL (SS480) CASTOR (AKSl) TOM GREEN...SOPA in USS Piedmont AD 17. SHIP BARBERO SSG317 BERING STRAIT WAVP382 BRUSH DD745 CARBONERO SS337 CASTOR AKSl GEORGE K MACKENZIE DD386 GURKE

Process for upgrading arsenic-containing oils

DOEpatents

Sullivan, Richard F.

1979-01-01

A method is provided for avoiding feed-transfer-line plugging by a deposit comprising arsenic in hydroprocessing an oil containing an arsenic contaminant. In the method, a mixture of hydrogen gas and the oil is formed in situ in a bed of porous particulate contact material.

Kristiina Iisa | NREL

Science.gov Websites

," Topics in Catalysis (2016) "Hydrotreating the Organic Fraction of Biomass Pyrolysis Oil to a Biomass via Hot-Vapor-Filtered Fast Pyrolysis and Catalytic Hydroprocessing of the Bio-oil," Energy & Fuels (2014) "Evaluate Impact of Catalyst Type on Oil Yield and Hydrogen Consumption from

Effect Of Iron On The Sensitivity Of Hydrogen, Acetate, And Butyrate Metabolism To Inhibition By Long-Chain Fatty Acids In Vegetable-Oil-Enriched Freshwater Sediments

EPA Science Inventory

Freshwater sediment microbial communities enriched by growth on vegetable oil in the presence of a substoichiometric amount of ferric hydroxide (sufficient to accept about 12% of the vegetable-oil-derived electrons) degrade vegetable oil to methane faster than similar microbial c...

Lipids as renewable resources: current state of chemical and biotechnological conversion and diversification.

PubMed

Metzger, J O; Bornscheuer, U

2006-06-01

Oils and fats are the most important renewable raw materials of the chemical industry. They make available fatty acids in such purity that they may be used for chemical conversions and for the synthesis of chemically pure compounds. Oleic acid (1) from "new sunflower," linoleic acid (2) from soybean, linolenic acid (3) from linseed, erucic acid (4) from rape seed, and ricinoleic acid (5) from castor oil are most important for chemical transformations offering in addition to the carboxy group one or more C-C-double bonds. New plant oils containing fatty acids with new and interesting functionalities such as petroselinic acid (6) from Coriandrum sativum, calendic acid (7) from Calendula officinalis, alpha-eleostearic acid (8) from tung oil, santalbic acid (9) from Santalum album (Linn.), and vernolic acid (10) from Vernonia galamensis are becoming industrially available. The basic oleochemicals are free fatty acids, methyl esters, fatty alcohols, and fatty amines as well as glycerol as a by-product. Their interesting new industrial applications are the usage as environmentally friendly industrial fluids and lubricants, insulating fluid for electric utilities such as transformers and additive to asphalt. Modern methods of synthetic organic chemistry including enzymatic and microbial transformations were applied extensively to fatty compounds for the selective functionalization of the alkyl chain. Syntheses of long-chain diacids, omega-hydroxy fatty acids, and omega-unsaturated fatty acids as base chemicals derived from vegetable oils were developed. Interesting applications were opened by the epoxidation of C-C-double bonds giving the possibility of photochemically initiated cationic curing and access to polyetherpolyols. Enantiomerically pure fatty acids as part of the chiral pool of nature can be used for the synthesis of nonracemic building blocks.

Genome-Wide Analysis of Oleosin Gene Family in 22 Tree Species: An Accelerator for Metabolic Engineering of BioFuel Crops and Agrigenomics Industrial Applications?

PubMed Central

2015-01-01

Abstract Trees contribute to enormous plant oil reserves because many trees contain 50%–80% of oil (triacylglycerols, TAGs) in the fruits and kernels. TAGs accumulate in subcellular structures called oil bodies/droplets, in which TAGs are covered by low-molecular-mass hydrophobic proteins called oleosins (OLEs). The OLEs/TAGs ratio determines the size and shape of intracellular oil bodies. There is a lack of comprehensive sequence analysis and structural information of OLEs among diverse trees. The objectives of this study were to identify OLEs from 22 tree species (e.g., tung tree, tea-oil tree, castor bean), perform genome-wide analysis of OLEs, classify OLEs, identify conserved sequence motifs and amino acid residues, and predict secondary and three-dimensional structures in tree OLEs and OLE subfamilies. Data mining identified 65 OLEs with perfect conservation of the “proline knot” motif (PX5SPX3P) from 19 trees. These OLEs contained >40% hydrophobic amino acid residues. They displayed similar properties and amino acid composition. Genome-wide phylogenetic analysis and multiple sequence alignment demonstrated that these proteins could be classified into five OLE subfamilies. There were distinct patterns of sequence conservation among the OLE subfamilies and within individual tree species. Computational modeling indicated that OLEs were composed of at least three α-helixes connected with short coils without any β-strand and that they exhibited distinct 3D structures and ligand binding sites. These analyses provide fundamental information in the similarity and specificity of diverse OLE isoforms within the same subfamily and among the different species, which should facilitate studying the structure-function relationship and identify critical amino acid residues in OLEs for metabolic engineering of tree TAGs. PMID:26258573

Genome-Wide Analysis of Oleosin Gene Family in 22 Tree Species: An Accelerator for Metabolic Engineering of BioFuel Crops and Agrigenomics Industrial Applications?

PubMed

Cao, Heping

2015-09-01

Trees contribute to enormous plant oil reserves because many trees contain 50%-80% of oil (triacylglycerols, TAGs) in the fruits and kernels. TAGs accumulate in subcellular structures called oil bodies/droplets, in which TAGs are covered by low-molecular-mass hydrophobic proteins called oleosins (OLEs). The OLEs/TAGs ratio determines the size and shape of intracellular oil bodies. There is a lack of comprehensive sequence analysis and structural information of OLEs among diverse trees. The objectives of this study were to identify OLEs from 22 tree species (e.g., tung tree, tea-oil tree, castor bean), perform genome-wide analysis of OLEs, classify OLEs, identify conserved sequence motifs and amino acid residues, and predict secondary and three-dimensional structures in tree OLEs and OLE subfamilies. Data mining identified 65 OLEs with perfect conservation of the "proline knot" motif (PX5SPX3P) from 19 trees. These OLEs contained >40% hydrophobic amino acid residues. They displayed similar properties and amino acid composition. Genome-wide phylogenetic analysis and multiple sequence alignment demonstrated that these proteins could be classified into five OLE subfamilies. There were distinct patterns of sequence conservation among the OLE subfamilies and within individual tree species. Computational modeling indicated that OLEs were composed of at least three α-helixes connected with short coils without any β-strand and that they exhibited distinct 3D structures and ligand binding sites. These analyses provide fundamental information in the similarity and specificity of diverse OLE isoforms within the same subfamily and among the different species, which should facilitate studying the structure-function relationship and identify critical amino acid residues in OLEs for metabolic engineering of tree TAGs.

Passively Targeted Curcumin-Loaded PEGylated PLGA Nanocapsules for Colon Cancer Therapy In Vivo

PubMed Central

Klippstein, Rebecca; Wang, Julie Tzu-Wen; El-Gogary, Riham I; Bai, Jie; Mustafa, Falisa; Rubio, Noelia; Bansal, Sukhvinder; Al-Jamal, Wafa T; Al-Jamal, Khuloud T

2015-01-01

Clinical applications of curcumin for the treatment of cancer and other chronic diseases have been mainly hindered by its short biological half-life and poor water solubility. Nanotechnology-based drug delivery systems have the potential to enhance the efficacy of poorly soluble drugs for systemic delivery. This study proposes the use of poly(lactic-co-glycolic acid) (PLGA)-based polymeric oil-cored nanocapsules (NCs) for curcumin loading and delivery to colon cancer in mice after systemic injection. Formulations of different oil compositions are prepared and characterized for their curcumin loading, physico-chemical properties, and shelf-life stability. The results indicate that castor oil-cored PLGA-based NC achieves high drug loading efficiency (≈18% w(drug)/w(polymer)%) compared to previously reported NCs. Curcumin-loaded NCs internalize more efficiently in CT26 cells than the free drug, and exert therapeutic activity in vitro, leading to apoptosis and blocking the cell cycle. In addition, the formulated NC exhibits an extended blood circulation profile compared to the non-PEGylated NC, and accumulates in the subcutaneous CT26-tumors in mice, after systemic administration. The results are confirmed by optical and single photon emission computed tomography/computed tomography (SPECT/CT) imaging. In vivo growth delay studies are performed, and significantly smaller tumor volumes are achieved compared to empty NC injected animals. This study shows the great potential of the formulated NC for treating colon cancer. PMID:26140363

Renewable synthetic diesel fuel from triglycerides and organic waste materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hillard, J.C.; Strassburger, R.S.

1986-03-01

A renewable, synthetic diesel fuel has been developed that employs ethanol and organic waste materials. These organic materials, such as soybean oil or animal fats, are hydrolized to yield a mixture of solid soap like materials and glycerol. These soaps, now soluble in ethanol, are blended with ethanol; the glycerol is nitrated and added as well as castor oil when necessary. The synthetic fuel is tailored to match petroleum diesel fuel in viscosity, lubricity and cetane quality and, therefore, does not require any engine modifications. Testing in a laboratory engine and in a production Oldsmobile Cutlass has revealed that thismore » synthetic fuel is superior to petroleum diesel fuel in vehicle efficiency, cetane quality, combustion noise, cold start characteristics, exhaust odor and emissions. Performance characteristics are indistinguishable from those of petroleum diesel fuel. These soaps are added to improve the calorific value, lubricity and cetane quality of the ethanol. The glycerol from the hydrolysis process is nitrated and added to the ethanol as an additional cetane quality improver. Caster oil is added to the fuel when necessary to match the viscosity and lubricity of petroleum diesel fuel as well as to act as a corrosion inhibitor, thereby, precluding any engine modifications. The cetane quality of the synthetic fuel is better than that of petroleum diesel as the fuel carries its own oxygen. The synthetic fuel is also completely miscible with petroleum diesel.« less

Life cycle assessment of hydrogenated biodiesel production from waste cooking oil using the catalytic cracking and hydrogenation method.

PubMed

Yano, Junya; Aoki, Tatsuki; Nakamura, Kazuo; Yamada, Kazuo; Sakai, Shin-ichi

2015-04-01

There is a worldwide trend towards stricter control of diesel exhaust emissions, however presently, there are technical impediments to the use of FAME (fatty acid methyl esters)-type biodiesel fuel (BDF). Although hydrogenated biodiesel (HBD) is anticipated as a new diesel fuel, the environmental performance of HBD and its utilization system have not been adequately clarified. Especially when waste cooking oil is used as feedstock, not only biofuel production but also the treatment of waste cooking oil is an important function for society. A life cycle assessment (LCA), including uncertainty analysis, was conducted to determine the environmental benefits (global warming, fossil fuel consumption, urban air pollution, and acidification) of HBD produced from waste cooking oil via catalytic cracking and hydrogenation, compared with fossil-derived diesel fuel or FAME-type BDF. Combined functional unit including "treatment of waste cooking oil" and "running diesel vehicle for household waste collection" was established in the context of Kyoto city, Japan. The calculation utilized characterization, damage, and integration factors identified by LIME2, which was based on an endpoint modeling method. The results show that if diesel vehicles that comply with the new Japanese long-term emissions gas standard are commonly used in the future, the benefit of FAME-type BDF will be relatively limited. Furthermore, the scenario that introduced HBD was most effective in reducing total environmental impact, meaning that a shift from FAME-type BDF to HBD would be more beneficial. Copyright © 2015 Elsevier Ltd. All rights reserved.

Feasibility of recommending certain replacement or alternative fats.

PubMed

Skeaff, C M

2009-05-01

Expert groups and public health authorities recommend that trans-fatty acid (TFA) intakes from industrially produced partially hydrogenated vegetable oils (PHVOs) should be less than 1% of total energy intake. The starting point for any regulatory or nonregulatory response to this recommendation is to assess the extent of the problem by determining where in the food supply TFAs are found and the amounts consumed in the population. Unfortunately, this is a particularly difficult task using traditional methods of dietary assessment inasmuch as food composition databases with TFA data are either nonexistent or incomplete in most countries. Current evidence on estimates of intake suggests there is high variability in TFA intakes and their food sources between countries. The ubiquitous presence of PHVOs in the global food supply in bakery products, deep-fried foods, snack foods, confectionery products and table spreads attests to their commercial value and convenience. However, their common use is more the result of historical convenience from an industry infrastructure developed over 50 years based on efficient, cost-effective hydrogenation of vegetable oils rather than any inherent sensory or physical superiority of the hydrogenated fats over purpose-made zero-trans fats and oils. Current global supply of appropriate zero-trans replacement fats high in cis-unsaturated fatty acids is insufficient to meet the demand if all PHVOs in the food supply were replaced. Regulatory action needs to be coordinated with supply to maximize the opportunity for health gains by replacing partially hydrogenated fats with purpose-ready zero-trans vegetable oils low in saturates and high in cis-unsaturates rather than animal fats and tropical oils high in saturated fatty acids.

Heat- and light-induced thiol-ene oligomerization of soybean oil-based polymercaptan

USDA-ARS?s Scientific Manuscript database

Polymercaptanized soybean oil (PMSO), the product of a thiol-ene reaction between soybean oil and hydrogen sulfide, is a material of interest as a lubricant additive and polymer precursor. We investigated with gel permeation chromatography, nuclear magnetic resonance (one-dimensional and two-dimensi...

Thermostable ricin vaccine protects rhesus macaques against aerosolized ricin: Epitope-specific neutralizing antibodies correlate with protection.

PubMed

Roy, Chad J; Brey, Robert N; Mantis, Nicholas J; Mapes, Kelly; Pop, Iliodora V; Pop, Laurentiu M; Ruback, Stephen; Killeen, Stephanie Z; Doyle-Meyers, Lara; Vinet-Oliphant, Heather S; Didier, Peter J; Vitetta, Ellen S

2015-03-24

Ricin toxin (RT) is the second most lethal toxin known; it has been designated by the CDC as a select agent. RT is made by the castor bean plant; an estimated 50,000 tons of RT are produced annually as a by-product of castor oil. RT has two subunits, a ribotoxic A chain (RTA) and galactose-binding B chain (RTB). RT binds to all mammalian cells and once internalized, a single RTA catalytically inactivates all of the ribosomes in a cell. Administered as an aerosol, RT causes rapid lung damage and fibrosis followed by death. There are no Food and Drug Administration-approved vaccines and treatments are only effective in the first few hours after exposure. We have developed a recombinant RTA vaccine that has two mutations V76M/Y80A (RiVax). The protein is expressed in Escherichia coli and is nontoxic and immunogenic in mice, rabbits, and humans. When vaccinated mice are challenged with injected, aerosolized, or orally administered (gavaged) RT, they are completely protected. We have now developed a thermostable, aluminum-adjuvant-containing formulation of RiVax and tested it in rhesus macaques. After three injections, the animals developed antibodies that completely protected them from a lethal dose of aerosolized RT. These antibodies neutralized RT and competed to varying degrees with a panel of neutralizing and nonneutralizing mouse monoclonal antibodies known to recognize specific epitopes on native RTA. The resulting antibody competition profile could represent an immunologic signature of protection. Importantly, the same signature was observed using sera from RiVax-immunized humans.

Pharmacologic Comparison of Clinical Neutral Endopeptidase Inhibitors in a Rat Model of Acute Secretory Diarrhea

PubMed Central

Prinsen, Michael J.; Oliva, Jonathan; Campbell, Mary A.; Arnett, Stacy D.; Tajfirouz, Deena; Ruminski, Peter G.; Yu, Ying; Bond, Brian R.; Ji, Yuhua; Neckermann, Georg; Choy, Robert K. M.; de Hostos, Eugenio; Meyers, Marvin J.

2016-01-01

Racecadotril (acetorphan) is a neutral endopeptidase (NEP) inhibitor with known antidiarrheal activity in animals and humans; however, in humans, it suffers from shortcomings that might be improved with newer drugs in this class that have progressed to the clinic for nonenteric disease indications. To identify potentially superior NEP inhibitors with immediate clinical utility for diarrhea treatment, we compared their efficacy and pharmacologic properties in a rat intestinal hypersecretion model. Racecadotril and seven other clinical-stage inhibitors of NEP were obtained or synthesized. Enzyme potency and specificity were compared using purified peptidases. Compounds were orally administered to rats before administration of castor oil to induce diarrhea. Stool weight was recorded over 4 hours. To assess other pharmacologic properties, select compounds were orally administered to normal or castor oil–treated rats, blood and tissue samples collected at multiple time points, and active compound concentrations determined by mass spectroscopy. NEP enzyme activity was measured in tissue homogenates. Three previously untested clinical NEP inhibitors delayed diarrhea onset and reduced total stool output, with little or no effect on intestinal motility assessed by the charcoal meal test. Each was shown to be a potent, highly specific inhibitor of NEP. Each exhibited greater suppression of NEP activity in intestinal and nonintestinal tissues than did racecadotril and sustained this inhibition longer. These results suggest that newer clinical-stage NEP inhibitors originally developed for other indications may be directly repositioned for treatment of acute secretory diarrhea and offer advantages over racecadotril, such as less frequent dosing and potentially improved efficacy. PMID:26907621

Process Evaluation - Steam Reforming of Diesel Fuel Oil

DTIC Science & Technology

1980-02-15

Table 9. HIDROGEN CONVERSION RELATIVE TO TEMPERATURE, SPACE, VELOCITY, AND H20/C RATIO Oil Feed, Gas Product ,Run No. Temperature, *F H2,O/C Ratio igram...steam reforming diesel fuel, but with the production of naphthalene after 30 hours. Hydrogen production remained stable through the 86 hours of the test...79-C-0048. Hydrogen-rich gas was produced over a wide range of reaction conditions. This product gas contained small amounts of ethylene and !nzene

Feasibility study: Liquid hydrogen plant, 30 tons per day

NASA Technical Reports Server (NTRS)

1975-01-01

The design considerations of the plant are discussed in detail along with management planning, objective schedules, and cost estimates. The processing scheme is aimed at ultimate use of coal as the basic raw material. For back-up, and to provide assurance of a dependable and steady supply of hydrogen, a parallel and redundant facility for gasifying heavy residual oil will be installed. Both the coal and residual oil gasifiers will use the partial oxidation process.

Trans-Fatty Acid-Stimulated Mammary Gland Growth in Ovariectomized Mice is Fatty Acid Type and Isomer Specific.

PubMed

Berryhill, Grace E; Miszewski, Susan G; Trott, Josephine F; Kraft, Jana; Lock, Adam L; Hovey, Russell C

2017-03-01

We previously reported that the trans-18:2 fatty acid trans-10, cis-12 conjugated linoleic acid (t10,c12-CLA) stimulates mammary gland development independent of estrogen and its receptor. Given the negative consequences of dietary trans-fatty acids on various aspects of human health, we sought to establish whether other trans-fatty acids could similarly induce ovary-independent mammary gland growth in mice. Prepubertal BALB/cJ mice were ovariectomized at 21 days of age then were fed diets enriched with cis-9, trans-11 CLA (c9,t11-CLA), or mixtures of trans-18:1 fatty acids supplied by partially hydrogenated sunflower, safflower, or linseed oil. The resultant mammary phenotype was evaluated 3 weeks later and compared to the growth response elicited by t10,c12-CLA, or the defined control diet. Whereas partially hydrogenated safflower oil increased mammary gland weight, none of the partially hydrogenated vegetable oils promoted mammary ductal growth. Similarly, the c9,t11-CLA supplemented diet was without effect on mammary development. Taken together, our data emphasize a unique effect of t10,c12-CLA in stimulating estrogen-independent mammary gland growth manifest as increased mammary ductal area and elongation that was not recapitulated by c9,t11-CLA or the partially hydrogenated vegetable oil diets.

Influence of phosphorous fertilization on copper phytoextraction and antioxidant defenses in castor bean (Ricinus communis L.).

PubMed

Huang, Guoyong; Rizwan, Muhammad Shahid; Ren, Chao; Guo, Guangguang; Fu, Qingling; Zhu, Jun; Hu, Hongqing

2018-01-01

Application of fertilizers to supply appropriate nutrients has become an essential agricultural strategy for enhancing the efficiency of phytoremediation in heavy metal contaminated soils. The present study was conducted to investigate the beneficial effects of three types of phosphate fertilizers (i.e., oxalic acid-activated phosphate rock (APR), Ca(H 2 PO 4 ) 2 , and NaH 2 PO 4 ) in the range of 0-600 mg P kg -1 soil, on castor bean growth, antioxidants [antioxidative enzymes and glutathione (GSH)], and Cu uptake. Results showed that with the addition of phosphorus fertilizers, the dry weight of castor bean and the Cu concentration in roots increased significantly, resulting in increased Cu extraction. The phosphorus concentration in both shoots and roots was increased as compared with the control, and the Ca(H 2 PO 4 ) 2 treatment had the greatest effect. Application of APR, NaH 2 PO 4 , and Ca(H 2 PO 4 ) 2 reduced the malondialdehyde (MDA) content, and the activity of the two antioxidant enzymes superoxide dismustase (SOD, EC 1.15.1.1) and catalase (CAT, EC 1.11.1.6) in the leaves of castor bean. GSH concentration in leaves increased with the increasing levels of phosphorus applied to soil as well as the accumulation of phosphorus in shoots, compared to the control. These results demonstrated that the addition of phosphorus fertilizers can enhance the resistance of castor bean to Cu and increase the Cu extraction efficiency of the plant from contaminated soils.

Dietary fish oil stimulates hepatic low density lipoprotein transport in the rat.

PubMed Central

Ventura, M A; Woollett, L A; Spady, D K

1989-01-01

These studies were undertaken to examine the effect of fish oil, safflower oil, and hydrogenated coconut oil on the major processes that determine the concentration of low density lipoprotein (LDL) in plasma, i.e., the rate of LDL production and the rates of receptor-dependent and receptor-independent LDL uptake in the various organs of the body. When fed at the 20% level, fish oil reduced plasma LDL-cholesterol levels by 38% primarily by increasing LDL receptor activity in the liver. Dietary safflower oil also increased hepatic LDL receptor activity; however, since the rate of LDL production also increased, plasma LDL-cholesterol levels remained essentially unchanged. Hydrogenated coconut oil had no effect on LDL receptor activity but increased the rate of LDL-cholesterol production causing plasma LDL-cholesterol levels to increase 46%. Dietary fish oil had no effect on the receptor-dependent transport of asialofetuin by the liver, suggesting that the effect of fish oil on hepatic LDL receptor activity was specific and not due to a generalized alteration in the physical properties of hepatic membranes. Finally, dietary fish oil increased hepatic cholesteryl ester levels and suppressed hepatic cholesterol synthesis rates, suggesting that the up-regulation of hepatic LDL receptor activity in these animals was not simply a response to diminished cholesterol availability in the liver. PMID:2760200

40 CFR Appendix III to Part 600 - Sample Fuel Economy Label Calculation

Code of Federal Regulations, 2011 CFR

2011-07-01

... miles per gallon. Note that the car line of the test vehicle using a given engine makes no difference... engine. These four car lines are: Ajax Boredom III Dodo Castor (Station Wagon) A. A car line is defined... different car line than the normal Castor car line made up of sedans, coupes, etc. B. The engine considered...

40 CFR Appendix III to Part 600 - Sample Fuel Economy Label Calculation

Code of Federal Regulations, 2014 CFR

2014-07-01

... miles per gallon. Note that the car line of the test vehicle using a given engine makes no difference... engine. These four car lines are: Ajax Boredom III Dodo Castor (Station Wagon) A. A car line is defined... different car line than the normal Castor car line made up of sedans, coupes, etc. B. The engine considered...

40 CFR Appendix III to Part 600 - Sample Fuel Economy Label Calculation

Code of Federal Regulations, 2013 CFR

2013-07-01

... miles per gallon. Note that the car line of the test vehicle using a given engine makes no difference... engine. These four car lines are: Ajax Boredom III Dodo Castor (Station Wagon) A. A car line is defined... different car line than the normal Castor car line made up of sedans, coupes, etc. B. The engine considered...

40 CFR Appendix III to Part 600 - Sample Fuel Economy Label Calculation

Code of Federal Regulations, 2012 CFR

2012-07-01

... miles per gallon. Note that the car line of the test vehicle using a given engine makes no difference... engine. These four car lines are: Ajax Boredom III Dodo Castor (Station Wagon) A. A car line is defined... different car line than the normal Castor car line made up of sedans, coupes, etc. B. The engine considered...

JPL-20180201-WHATSUf-0001-Whats Up February 2018

NASA Image and Video Library

2018-02-01

Monthly series for amateur astronomers. February features "celestial pairs" in honor of Valentine's Day. Constellation pairs: Perseus and Andromeda, Orion and the Pleiades. Star pairs: Pollux and Castor, Rigel and Rigel B, Mintaka and its companion star. Plus the moon pairs with Pollux and Castor and with the Pleiades. Includes animation of the myths of Perseus, Andromeda, Orion and the Pleiades.

43 CFR 2361.0-5 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... resources which include crude oil, gases of all kinds (natural gas, hydrogen, carbon dioxide, helium, and....), oil shale and the products of such resources. (d) Reserve means those lands within the National...

43 CFR 2361.0-5 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... resources which include crude oil, gases of all kinds (natural gas, hydrogen, carbon dioxide, helium, and....), oil shale and the products of such resources. (d) Reserve means those lands within the National...

43 CFR 2361.0-5 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... resources which include crude oil, gases of all kinds (natural gas, hydrogen, carbon dioxide, helium, and....), oil shale and the products of such resources. (d) Reserve means those lands within the National...

43 CFR 2361.0-5 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... resources which include crude oil, gases of all kinds (natural gas, hydrogen, carbon dioxide, helium, and....), oil shale and the products of such resources. (d) Reserve means those lands within the National...

Structural and Thermal Behavior of Meglumine-Based Supra-Amphiphiles in Bulk and Assembled in Water.

PubMed

Ferreira, Leonardo M B; Kurokawa, Suzy S S; Alonso, Jovan D; Cassimiro, Douglas Lopes; Souza, Ana Luiza Ribeiro de; Fonseca, Mariana; Sarmento, Victor Hugo V; Regasini, Luis Octávio; Ribeiro, Clóvis Augusto

2016-11-15

Supra-amphiphiles are a new class of building blocks that are fabricated by means of noncovalent forces. In this work, we studied the formation of supra-amphiphiles by combining hydrophilic meglumine (MEG) with hydrophobic maleated castor oils (MACO). Spectroscopic analysis demonstrated that ionic interactions are the main driving force in the fabrication of these materials. Subsequently, supra-amphiphile/water systems were examined for their structure and water behavior by polarized optical microscopy (POM), small-angle X-ray scattering (SAXS), and differential scanning calorimetry (DSC). Micellar and lamellar liquid crystalline phases were observed. Finally, we observed that the supra-amphiphiles produced using an excess of MEG retain a large amount of water. As bound water plays an important role in biointerfacial interactions, we anticipate that these materials will display a pronounced potential for biomedical applications.

[Natural infection of Lutzomyia cayennensis cayennensis with trypanosomatid parasites (Kinetoplastida: Trypanosomatidae) in Los Montes de Maria, Colombia].

PubMed

Cochero, Suljey; Anaya, Yosed; Díaz, Yirys; Paternina, Margaret; Luna, Arturo; Paternina, Luis; Eduar Elías, Bejarano

2007-01-01

The presence of sand flies naturally infected with trypanosomatid parasites was determined in Los Montes de Maria, Colombia, a region considered endemic for visceral and cutaneous leishmaniasis. Phlebotomines were collected using CDC light-traps, and sticky traps soaked with castor oil placed in the peri and intradomestic habitats. Six species of Lutzomyia were morphologically identified among the 159 sand flies captured: Lu. evansi, Lu. cayennensis cayennensis, Lu. trinidadensis, Lu. atroclavata, Lu. gomezi and Lu. dubitans. A DNA band of 800 pb corresponding to the small-subunit ribosomal RNA gene (ssrRNA) of the family Trypanosomatidae was amplified in one pool of nine females of Lu. cayennensis cayennensis. This finding constitutes the first evidence of natural infection of this sand fly species with trypanosomatid parasites in Los Montes de Maria.

Methods for nanoparticle labeling of ricin and effect on toxicity

NASA Astrophysics Data System (ADS)

Wark, Alastair W.; Yu, Jun; Lindsay, Christopher D.; Nativo, Paola; Graham, Duncan

2009-09-01

The unique optical properties associated with nanostructured materials that support the excitation of surface plasmons offer many new opportunities for the enhanced optical investigation of biological materials that pose a security threat. In particular, ricin is considered a significant bioterrorism risk due to its high toxicity combined with its ready availability as a byproduct in castor oil production. Therefore, the development of optical techniques capable of rapid on-site toxin detection with high molecular specificity and sensitivity continues to be of significant importance. Furthermore, understanding of the ricin cell entry and intracellular pathways remains poor due to a lack of suitable bioanalytical techniques. Initial work aimed at simultaneously tackling both these issues is described where different approaches for the nanoparticle labeling of ricin are investigated along with changes in ricin toxicity associated with the labeling process.

Physical properties of beeswax, sunflower wax, and candelilla wax mixtures and organogels

USDA-ARS?s Scientific Manuscript database

There is increased interest in natural waxes as alternatives to partially hydrogenated oils and saturated fats as oil structuring agents. Using relatively low concentrations (0.5-5%), natural waxes are able to form crystalline networks, or organogels, which bind liquid oil. Each natural wax is uniqu...

21 CFR 172.818 - Oxystearin.

Code of Federal Regulations, 2011 CFR

2011-04-01

...) It is used or intended for use as a crystallization inhibitor in vegetable oils and as a release agent in vegetable oils and vegetable shortenings, whereby the additive does not exceed 0.125 percent of... heating hydrogenated cottonseed or soybean oil under controlled conditions, in the presence of air and a...

Intraparticle diffusion limitations in the hydrogenation of monounsaturated edible oils and their fatty acid methyl esters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jonker, G.H.; Veldsink, J.W.; Beenackers, A.A.C.M.

1998-12-01

Intraparticle diffusion limitation in the hydrogenation and isomerization of fatty acid methyl esters (FAMEs) and edible oils (triacylglycerol, TAG) in porous nickel catalyst was investigated both under reactive and under inert conditions. Under reactive conditions, the diffusion coefficients were determined from the best fits of the model simulations applying the intrinsic reacting kinetics of monounsaturated FAME hydrogenation to experiments under diffusion limited conditions. Due to the absence of reaction (hydrogenation of double bonds), the obtained effective H{sub z} diffusion coefficient (D{sub e}) with the HPLC technique is volume averaged and thereby determined by the larger intercrystalline pores (<30% of themore » total pore volume) only. Moreover, D{sub e} measured under reaction conditions reflected the influence of the micropores, resulting in a 10-fold lower value.« less

Selective hydrodesulfurization of 4,6-dimethyl-dibenzothiophene in the dominant presence of naphthalene over hybrid CoMo/Al{sub 2}O{sub 3} and Ru/Al{sub 2}O{sub 3} catalysts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Isoda, Takaaki; Nagao, Shinichi; Ma, Xiaoliang

1995-12-31

It has been revealed that significant desulfurization of refractory 4-methyldibenzothiophene and 4,6-dimethyldibenzothiophene (4,6-DMDBT) is very essential to achive the low sulfur level of gas oil requested by the current regulation. Their direct desulfurization through the interaction of their sulfur atom with the catalyst surface is sterically hindered by its neighbouring methyl groups. The substrate is found kinetically to be hydrogenated at one of its phenyl rings prior to the desulfurization in order to reduce the steric hindrance through non-planaring configuration (2-4). NiMo / Al{sub 2}O{sub 3} was reported to be superior to CoMo / Al{sub 2}O{sub 3} in the deepmore » desulufurization, because of its higher hydrogenation activity. However, such a hydrogenation route suffers severe inhibition by aromatic species in their dominant presence, because 4,6-DMDBT must compete with the aromatic species to the hydrogenation sites on the catalysts. The aromatic species up to 30 wt % in the gas oil was that completely stop the desulfurization of the particular substrate. The catalyst for the selective hydrogenation of 4,6-DMDBT in the dominant aromatic partners is most wanted to achive its extensive desulfurization in the gas oil, although there have been reported activities of various transition metal sulfides for HDS of dibenzothiophene, and hydrogenation of aromatic hydrocarbons.« less

Electrohydrodynamics of a particle-covered drop

NASA Astrophysics Data System (ADS)

Ouriemi, Malika; Vlahovska, Petia

2014-11-01

We study the dynamics of a drop nearly-completely covered with a particle monolayer in a uniform DC electric field. The weakly conducting fluid system consists of a silicon oil drop suspended in castor oil. A broad range of particle sizes, conductivities, and shapes is explored. In weak electric fields, the presence of particles increases drop deformation compared to a particle-free drop and suppresses the electrohydrodynamic flow. Very good agreement is observed between the measured drop deformation and the small deformation theory derived for surfactant-laden drops (Nganguia et al., 2013). In stronger electric fields, where drops are expected to undergo Quincke rotation (Salipante and Vlahovska, 2010), the presence of the particles greatly decreases the threshold for rotation and the stationary tilted drop configuration observed for clean drop is replaced by a spinning drop with either a wobbling inclination or a very low inclination. These behaviors resemble the predicted response of rigid ellipsoids in uniform electric fields. At even stronger electric fields, the particles can form dynamic wings or the drop implodes. The similar behavior of particle-covered and surfactant-laden drops provides new insights into understanding stability of Pickering emulsions. Supported by NSF-CBET 1437545.

Transdermal delivery of paeonol using cubic gel and microemulsion gel

PubMed Central

Luo, Maofu; Shen, Qi; Chen, Jinjin

2011-01-01

Background The aim of this study was to develop new systems for transdermal delivery of paeonol, in particular microemulsion gel and cubic gel formulations. Methods Various microemulsion vehicles were prepared using isopropyl myristate as an oil phase, polyoxyethylated castor oil (Cremophor® EL) as a surfactant, and polyethylene glycol 400 as a cosurfactant. In the optimum microemulsion gel formulation, carbomer 940 was selected as the gel matrix, and consisted of 1% paeonol, 4% isopropyl myristate, 28% Cremophor EL/polyethylene glycol 400 (1:1), and 67% water. The cubic gel was prepared containing 3% paeonol, 30% water, and 67% glyceryl monooleate. Results A skin permeability test using excised rat skins indicated that both the cubic gel and microemulsion gel formulations had higher permeability than did the paeonol solution. An in vivo pharmacokinetic study done in rats showed that the relative bioavailability of the cubic gel and microemulsion gel was enhanced by about 1.51-fold and 1.28-fold, respectively, compared with orally administered paeonol suspension. Conclusion Both the cubic gel and microemulsion gel formulations are promising delivery systems to enhance the skin permeability of paeonol, in particular the cubic gel. PMID:21904450