Proficiency Testing as a tool to monitor consistency of measurements in the IAEA/WHO Network of Secondary Standards Dosimetry Laboratories

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meghzifene, Ahmed; Czap, Ladislav; Shortt, Ken

2008-08-14

The International Atomic Energy Agency (IAEA) and the World Health Organization (WHO) established a Network of Secondary Standards Dosimetry Laboratories (IAEA/WHO SSDL Network) in 1976. Through SSDLs designated by Member States, the Network provides a direct link of national dosimetry standards to the international measurement system of standards traceable to the Bureau International des Poids et Mesures (BIPM). Within this structure and through the proper calibration of field instruments, the SSDLs disseminate S.I. quantities and units.To ensure that the services provided by SSDL members to end-users follow internationally accepted standards, the IAEA has set up two different comparison programmes. Onemore » programme relies on the IAEA/WHO postal TLD service and the other uses comparisons of calibrated ionization chambers to help the SSDLs verify the integrity of their national standards and the procedures used for the transfer of the standards to the end-users. The IAEA comparisons include {sup 60}Co air kerma (N{sub K}) and absorbed dose to water (N{sub D,W}) coefficients. The results of the comparisons are confidential and are communicated only to the participants. This is to encourage participation of the laboratories and their full cooperation in the reconciliation of any discrepancy.This work describes the results of the IAEA programme comparing calibration coefficients for radiotherapy dosimetry, using ionization chambers. In this programme, ionization chambers that belong to the SSDLs are calibrated sequentially at the SSDL, at the IAEA, and again at the SSDL. As part of its own quality assurance programme, the IAEA has participated in several regional comparisons organized by Regional Metrology Organizations.The results of the IAEA comparison programme show that the majority of SSDLs are capable of providing calibrations that fall inside the acceptance level of 1.5% compared to the IAEA.« less

The U.S./IAEA Workshop on Software Sustainability for Safeguards Instrumentation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pepper S. E.; .; Worrall, L.

2014-08-08

The U.S. National Nuclear Security Administration’s Next Generation Safeguards Initiative, the U.S. Department of State, and the International Atomic Energy Agency (IAEA) organized a a workshop on the subject of ”Software Sustainability for Safeguards Instrumentation.” The workshop was held at the Vienna International Centre in Vienna, Austria, May 6-8, 2014. The workshop participants included software and hardware experts from national laboratories, industry, government, and IAEA member states who were specially selected by the workshop organizers based on their experience with software that is developed for the control and operation of safeguards instrumentation. The workshop included presentations, to orient the participantsmore » to the IAEA Department of Safeguards software activities related to instrumentation data collection and processing, and case studies that were designed to inspire discussion of software development, use, maintenance, and upgrades in breakout sessions and to result in recommendations for effective software practices and management. This report summarizes the results of the workshop.« less

10 CFR 75.12 - Communication of information to IAEA.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Communication of information to IAEA. 75.12 Section 75.12 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) SAFEGUARDS ON NUCLEAR MATERIAL-IMPLEMENTATION OF US/IAEA AGREEMENT Facility and Location Information § 75.12 Communication of information to IAEA. (a) Except as...

10 CFR 75.12 - Communication of information to IAEA.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 2 2011-01-01 2011-01-01 false Communication of information to IAEA. 75.12 Section 75.12 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) SAFEGUARDS ON NUCLEAR MATERIAL-IMPLEMENTATION OF US/IAEA AGREEMENT Facility and Location Information § 75.12 Communication of information to IAEA. (a) Except as...

IAEA Nuclear Data Section: provision of atomic and nuclear databases for user applications.

PubMed

Humbert, Denis P; Nichols, Alan L; Schwerer, Otto

2004-01-01

The Nuclear Data Section (NDS) of the International Atomic Energy Agency (IAEA) provides a wide range of atomic and nuclear data services to scientists worldwide, with particular emphasis placed on the needs of developing countries. Highly focused Co-ordinated Research Projects and multinational data networks are sponsored under the auspices of the IAEA for the development and assembly of databases through the organised participation of specialists from Member States. More than 100 data libraries are readily available cost-free through the Internet, CD-ROM and other media. These databases are used in a wide range of applications, including fission- and fusion-energy, non-energy applications and basic research studies. Further information concerning the various services can be found through the web address of the IAEA Nuclear Data Section: and a mirror site at IPEN, Brazil that is maintained by NDS staff:.

Contribution to fusion research from IAEA coordinated research projects and joint experiments

NASA Astrophysics Data System (ADS)

Gryaznevich, M.; Van Oost, G.; Stöckel, J.; Kamendje, R.; Kuteev, B. N.; Melnikov, A.; Popov, T.; Svoboda, V.; The IAEA CRP Teams

2015-10-01

The paper presents objectives and activities of IAEA Coordinated Research Projects ‘Conceptual development of steady-state compact fusion neutron sources’ and ‘Utilisation of a network of small magnetic confinement fusion devices for mainstream fusion research’. The background and main projects of the CRP on FNS are described in detail, as this is a new activity at IAEA. Recent activities of the second CRP, which continues activities of previous CRPs, are overviewed.

Improving Quality and Access to Radiation Therapy-An IAEA Perspective.

PubMed

Abdel-Wahab, May; Zubizarreta, Eduardo; Polo, Alfredo; Meghzifene, Ahmed

2017-04-01

The International Atomic Energy Agency (IAEA) has been involved in radiation therapy since soon after its creation in 1957. In response to the demands of Member States, the IAEA׳s activities relating to radiation therapy have focused on supporting low- and middle-income countries to set up radiation therapy facilities, expand the scope of treatments, or gradually transition to new technologies. In addition, the IAEA has been very active in providing internationally harmonized guidelines on clinical, dosimetry, medical physics, and safety aspects of radiation therapy. IAEA clinical research has provided evidence for treatment improvement as well as highly effective resource-sparing interventions. In the process, training of researchers occurs through this program. To provide this support, the IAEA works with its Member States and multiple partners worldwide through several mechanisms. In this article, we review the main activities conducted by the IAEA in support to radiation therapy. IAEA support has been crucial for achieving tangible results in many low- and middle-income countries. However, long-term sustainability of projects can present a challenge, especially when considering health budget constraints and the brain drain of skilled professionals. The need for support remains, with more than 90% of patients in low-income countries lacking access to radiotherapy. Thus, the IAEA is expected to continue its support and strengthen quality radiation therapy treatment of patients with cancer. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

IAEA activities in the area of partitioning and transmutation

NASA Astrophysics Data System (ADS)

Stanculescu, Alexander

2006-06-01

Four major challenges are facing the long-term development of nuclear energy: improvement of the economic competitiveness, meeting increasingly stringent safety requirements, adhering to the criteria of sustainable development, and public acceptance. Meeting the sustainability criteria is the driving force behind the topic of this paper. In this context, sustainability has two aspects: natural resources and waste management. IAEA's activities in the area of Partitioning and Transmutation (P&T) are mostly in response to the latter. While not involving the large quantities of gaseous products and toxic solid wastes associated with fossil fuels, radioactive waste disposal is today's dominant public acceptance issue. In fact, small waste quantities permit a rigorous confinement strategy, and mined geological disposal is the strategy followed by some countries. Nevertheless, political opposition arguing that this does not yet constitute a safe disposal technology has largely stalled these efforts. One of the primary reasons cited is the long life of many of the radioisotopes generated from fission. This concern has led to increased R&D efforts to develop a technology aimed at reducing the amount and radio-toxicity of long-lived radioactive waste through transmutation in fission reactors or sub-critical systems. In the frame of the Project on Technology Advances in Fast Reactors and Accelerator-Driven Systems (ADS), the IAEA initiated a number of activities on utilization of plutonium and transmutation of long-lived radioactive waste, ADS, and deuterium-tritium plasma-driven sub-critical systems. The paper presents past accomplishments, current status and planned activities of this IAEA project.

Training of interventional cardiologists in radiation protection--the IAEA's initiatives.

PubMed

Rehani, Madan M

2007-01-08

The International Atomic Energy Agency (IAEA) has initiated a major international initiative to train interventional cardiologists in radiation protection as a part of its International Action Plan on the radiological protection of patients. A simple programme of two days' training has been developed, covering possible and observed radiation effects among patients and staff, international standards, dose management techniques, examples of good and bad practice and examples indicating prevention of possible injuries as a result of good practice of radiation protection. The training material is freely available on CD from the IAEA. The IAEA has conducted two events in 2004 and 2005 and number of events are planned in 2006. The survey conducted among the cardiologists participating in these programmes indicates that over 80% of them were attending such a structured programme on radiation protection for the first time. As the magnitude of X-ray usage in cardiology grows to match that in interventional radiology, the standards of training on radiation effects, radiation physics and radiation protection in interventional cardiology should also match those in interventional radiology.

IAEA Sampling Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Geist, William H.

2017-09-15

The objectives for this presentation are to describe the method that the IAEA uses to determine a sampling plan for nuclear material measurements; describe the terms detection probability and significant quantity; list the three nuclear materials measurement types; describe the sampling method applied to an item facility; and describe multiple method sampling.

Strengthening IAEA Safeguards for Research Reactors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reid, Bruce D.; Anzelon, George A.; Budlong-Sylvester, Kory

During their December 10-11, 2013, workshop in Grenoble France, which focused on the history and future of safeguarding research reactors, the United States, France and the United Kingdom (UK) agreed to conduct a joint study exploring ways to strengthen the IAEA’s safeguards approach for declared research reactors. This decision was prompted by concerns about: 1) historical cases of non-compliance involving misuse (including the use of non-nuclear materials for production of neutron generators for weapons) and diversion that were discovered, in many cases, long after the violations took place and as part of broader pattern of undeclared activities in half amore » dozen countries; 2) the fact that, under the Safeguards Criteria, the IAEA inspects some reactors (e.g., those with power levels under 25 MWt) less than once per year; 3) the long-standing precedent of States using heavy water research reactors (HWRR) to produce plutonium for weapons programs; 4) the use of HEU fuel in some research reactors; and 5) various technical characteristics common to some types of research reactors that could provide an opportunity for potential proliferators to misuse the facility or divert material with low probability of detection by the IAEA. In some research reactors it is difficult to detect diversion or undeclared irradiation. In addition, infrastructure associated with research reactors could pose a safeguards challenge. To strengthen the effectiveness of safeguards at the State level, this paper advocates that the IAEA consider ways to focus additional attention and broaden its safeguards toolbox for research reactors. This increase in focus on the research reactors could begin with the recognition that the research reactor (of any size) could be a common path element on a large number of technically plausible pathways that must be considered when performing acquisition pathway analysis (APA) for developing a State Level Approach (SLA) and Annual Implementation Plan

Continuation of advanced crew procedures development techniques

NASA Technical Reports Server (NTRS)

Arbet, J. D.; Benbow, R. L.; Evans, M. E.; Mangiaracina, A. A.; Mcgavern, J. L.; Spangler, M. C.; Tatum, I. C.

1976-01-01

An operational computer program, the Procedures and Performance Program (PPP) which operates in conjunction with the Phase I Shuttle Procedures Simulator to provide a procedures recording and crew/vehicle performance monitoring capability was developed. A technical synopsis of each task resulting in the development of the Procedures and Performance Program is provided. Conclusions and recommendations for action leading to the improvements in production of crew procedures development and crew training support are included. The PPP provides real-time CRT displays and post-run hardcopy output of procedures, difference procedures, performance data, parametric analysis data, and training script/training status data. During post-run, the program is designed to support evaluation through the reconstruction of displays to any point in time. A permanent record of the simulation exercise can be obtained via hardcopy output of the display data and via transfer to the Generalized Documentation Processor (GDP). Reference procedures data may be transferred from the GDP to the PPP. Interface is provided with the all digital trajectory program, the Space Vehicle Dynamics Simulator (SVDS) to support initial procedures timeline development.

WE-AB-213-04: IAEA Support to Medical Physics in Africa and Latin America: Achievements and Challenges

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meghzifene, A.

a medical physicist, whose degree of involvement is determined by the complexity of the radiological procedures and the associated radiation risks”. Details on how these requirements can be carried out in resource-limited settings will be described. IAEA support to medical physics in Africa and Latin America: achievements and challenges Ahmed Meghzifene (IAEA) Shortage of clinically qualified medical physicists in radiotherapy and imaging, insufficient and inadequate education and training programs, as well as a lack of professional recognition were identified as the main issues to be addressed by the IAEA. The IAEA developed a series of integrated projects aiming specifically at promoting the essential role of medical physicists in health care, developing harmonized guidelines on dosimetry and quality assurance, and supporting education and clinical training programs. The unique feature of the IAEA approach is support it provides for implementation of guidelines and education programs in Member States through its technical cooperation project. The presentation will summarize IAEA support to Latin America and Africa in the field of medical physics and will highlight how the new International Basic Safety Standards are expected to impact the medical physics practice in low and middle income countries. Learning Objectives: Learn about the shortage of qualified Medical Physicists in Africa and Latin America. Understand the reasons of this shortage. Learn about the ways to improve the situation and AAPM role in this process.« less

Advanced crew procedures development techniques

NASA Technical Reports Server (NTRS)

Arbet, J. D.; Benbow, R. L.; Mangiaracina, A. A.; Mcgavern, J. L.; Spangler, M. C.; Tatum, I. C.

1975-01-01

The development of an operational computer program, the Procedures and Performance Program (PPP), is reported which provides a procedures recording and crew/vehicle performance monitoring capability. The PPP provides real time CRT displays and postrun hardcopy of procedures, difference procedures, performance, performance evaluation, and training script/training status data. During post-run, the program is designed to support evaluation through the reconstruction of displays to any point in time. A permanent record of the simulation exercise can be obtained via hardcopy output of the display data, and via magnetic tape transfer to the Generalized Documentation Processor (GDP). Reference procedures data may be transferred from the GDP to the PPP.

International Scavenging for First Responder Guidance and Tools: IAEA Products

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stern, W.; Berthelot, L.; Bachner, K.

In fiscal years (FY) 2016 and 2017, with support from the U.S. Department of Homeland Security (DHS), Brookhaven National Laboratory (BNL) examined the International Atomic Energy Agency (IAEA) radiological emergency response and preparedness products (guidance and tools) to determine which of these products could be useful to U.S. first responders. The IAEA Incident and Emergency Centre (IEC), which is responsible for emergency preparedness and response, offers a range of tools and guidance documents for responders in recognizing, responding to, and recovering from radiation emergencies and incidents. In order to implement this project, BNL obtained all potentially relevant tools and productsmore » produced by the IAEA IEC and analyzed these materials to determine their relevance to first responders in the U.S. Subsequently, BNL organized and hosted a workshop at DHS National Urban Security Technology Laboratory (NUSTL) for U.S. first responders to examine and evaluate IAEA products to consider their applicability to the United States. This report documents and describes the First Responder Product Evaluation Workshop, and provides recommendations on potential steps the U.S. federal government could take to make IAEA guidance and tools useful to U.S. responders.« less

RELAP5 posttest calculation of IAEA-SPE-4

DOE Office of Scientific and Technical Information (OSTI.GOV)

Petelin, S.; Mavko, B.; Parzer, I.

The International Atomic Energy Agency`s Fourth Standard Problem Exercise (IAEA-SPE-4) was performed at the PMK-2 facility. The PMK-2 facility is designed to study processes following small- and medium-size breaks in the primary system and natural circulation in VVER-440 plants. The IAEA-SPE-4 experiment represents a cold-leg side small break, similar to the IAEA-SPE-2, with the exception of the high-pressure safety injection being unavailable, and the secondary side bleed and feed initiation. The break valve was located at the dead end of a vertical downcomer, which in fact simulates a break in the reactor vessel itself, and should be unlikely to happenmore » in a real nuclear power plant (NPP). Three different RELAP5 code versions were used for the transient simulation in order to assess the calculations with test results.« less

Apollo experience report: Systems and flight procedures development

NASA Technical Reports Server (NTRS)

Kramer, P. C.

1973-01-01

This report describes the process of crew procedures development used in the Apollo Program. The two major categories, Systems Procedures and Flight Procedures, are defined, as are the forms of documentation required. A description is provided of the operation of the procedures change control process, which includes the roles of man-in-the-loop simulations and the Crew Procedures Change Board. Brief discussions of significant aspects of the attitude control, computer, electrical power, environmental control, and propulsion subsystems procedures development are presented. Flight procedures are subdivided by mission phase: launch and translunar injection, rendezvous, lunar descent and ascent, and entry. Procedures used for each mission phase are summarized.

10 CFR 150.17a - Compliance with requirements of US/IAEA Safeguards Agreement.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 2 2011-01-01 2011-01-01 false Compliance with requirements of US/IAEA Safeguards... Authority in Agreement States § 150.17a Compliance with requirements of US/IAEA Safeguards Agreement. (a... shall take other action as may be necessary to implement the US/IAEA Safeguards Agreement, as described...

10 CFR 150.17a - Compliance with requirements of US/IAEA Safeguards Agreement.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Compliance with requirements of US/IAEA Safeguards... Authority in Agreement States § 150.17a Compliance with requirements of US/IAEA Safeguards Agreement. (a... shall take other action as may be necessary to implement the US/IAEA Safeguards Agreement, as described...

Developing Procedural Flexibility: Are Novices Prepared to Learn from Comparing Procedures?

ERIC Educational Resources Information Center

Rittle-Johnson, Bethany; Star, Jon R.; Durkin, Kelley

2012-01-01

Background: A key learning outcome in problem-solving domains is the development of procedural flexibility, where learners know multiple procedures and use them appropriately to solve a range of problems (e.g., Verschaffel, Luwel, Torbeyns, & Van Dooren, 2009). However, students often fail to become flexible problem solvers in mathematics. To…

25 CFR 33.9 - Development of procedures.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 25 Indians 1 2011-04-01 2011-04-01 false Development of procedures. 33.9 Section 33.9 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR EDUCATION TRANSFER OF INDIAN EDUCATION FUNCTIONS § 33.9 Development of procedures. The Director, Office of Indian Education Programs shall prepare and...

25 CFR 33.9 - Development of procedures.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Development of procedures. 33.9 Section 33.9 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR EDUCATION TRANSFER OF INDIAN EDUCATION FUNCTIONS § 33.9 Development of procedures. The Director, Office of Indian Education Programs shall prepare and...

Department of Energy Efforts to Promote Universal Adherence to the IAEA Additional Protocol

DOE Office of Scientific and Technical Information (OSTI.GOV)

Killinger, Mark H.; Hansen, Linda H.; Kovacic, Don N.

2009-10-06

Entry-into-force of the U.S. Additional Protocol (AP) in January 2009 continues to demonstrate the ongoing commitment by the United States to promote universal adherence to the AP. The AP is a critical tool for improving the International Atomic Energy Agency’s (IAEA) capabilities to detect undeclared activities that indicate a clandestine nuclear weapons program. This is because States Parties are required to provide information about, and access to, nuclear fuel cycle activities beyond their traditional safeguards reporting requirements. As part of the U.S. AP Implementation Act and Senate Resolution of Ratification, the Administration is required to report annually to Congress onmore » measures taken to achieve the adoption of the AP in non-nuclear weapon states, as well as assistance to the IAEA to promote the effective implementation of APs in those states. A key U.S. effort in this area is being managed by the International Nuclear Safeguards and Engagement Program (INSEP) of the U.S. Department of Energy (DOE). Through new and existing bilateral cooperation agreements, INSEP has initiated technical assistance projects for AP implementation with selected non-weapon states. States with which INSEP is currently cooperating include Vietnam and Thailand, with Indonesia, Algeria, Morocco, and other countries as possible future collaborators in the area of AP implementation. The INSEP collaborative model begins with a joint assessment with our partners to identify specific needs they may have regarding entering the AP into force and any impediments to successful implementation. An action plan is then developed detailing and prioritizing the necessary joint activities. Such assistance may include: advice on developing legal frameworks and regulatory documents; workshops to promote understanding of AP requirements; training to determine possible declarable activities; assistance in developing a system to collect and submit declarations; performing industry

Hybrid imaging worldwide-challenges and opportunities for the developing world: a report of a Technical Meeting organized by IAEA.

PubMed

Kashyap, Ravi; Dondi, Maurizio; Paez, Diana; Mariani, Guliano

2013-05-01

The growth in nuclear medicine, in the past decade, is largely due to hybrid imaging, specifically single-photon emission tomography-computed tomography (SPECT-CT) and positron emission tomography-computed tomography (PET-CT). Introduction and use of hybrid imaging has been growing at a fast pace. This has led to many challenges and opportunities to the personnel dealing with it. The International Atomic Energy Agency (IAEA) keeps a close watch on the trends in applications of nuclear techniques in health by many ways, including obtaining inputs from member states and professional societies. In 2012, a Technical Meeting on trends in hybrid imaging was organized by IAEA to understand the current status and trends of hybrid imaging using nuclear techniques, its role in clinical practice, and associated educational needs and challenges. Perspective of scientific societies and professionals from all the regions of the world was obtained. Heterogeneity in value, educational needs, and access was noted and the drivers of this heterogeneity were discussed. This article presents the key points shared during the technical meeting, focusing primarily on SPECT-CT and PET-CT, and shares the action plan for IAEA to deal with heterogeneity as suggested by the participants. Copyright © 2013 Elsevier Inc. All rights reserved.

Fault displacement hazard assessment for nuclear installations based on IAEA safety standards

NASA Astrophysics Data System (ADS)

Fukushima, Y.

2016-12-01

In the IAEA Safety NS-R-3, surface fault displacement hazard assessment (FDHA) is required for the siting of nuclear installations. If any capable faults exist in the candidate site, IAEA recommends the consideration of alternative sites. However, due to the progress in palaeoseismological investigations, capable faults may be found in existing site. In such a case, IAEA recommends to evaluate the safety using probabilistic FDHA (PFDHA), which is an empirical approach based on still quite limited database. Therefore a basic and crucial improvement is to increase the database. In 2015, IAEA produced a TecDoc-1767 on Palaeoseismology as a reference for the identification of capable faults. Another IAEA Safety Report 85 on ground motion simulation based on fault rupture modelling provides an annex introducing recent PFDHAs and fault displacement simulation methodologies. The IAEA expanded the project of FDHA for the probabilistic approach and the physics based fault rupture modelling. The first approach needs a refinement of the empirical methods by building a world wide database, and the second approach needs to shift from kinematic to the dynamic scheme. Both approaches can complement each other, since simulated displacement can fill the gap of a sparse database and geological observations can be useful to calibrate the simulations. The IAEA already supported a workshop in October 2015 to discuss the existing databases with the aim of creating a common worldwide database. A consensus of a unified database was reached. The next milestone is to fill the database with as many fault rupture data sets as possible. Another IAEA work group had a WS in November 2015 to discuss the state-of-the-art PFDHA as well as simulation methodologies. Two groups jointed a consultancy meeting in February 2016, shared information, identified issues, discussed goals and outputs, and scheduled future meetings. Now we may aim at coordinating activities for the whole FDHA tasks jointly.

IAEA activities on atomic, molecular and plasma-material interaction data for fusion

NASA Astrophysics Data System (ADS)

Braams, Bastiaan J.; Chung, Hyun-Kyung

2013-09-01

The IAEA Atomic and Molecular Data Unit (http://www-amdis.iaea.org/) aims to provide internationally evaluated and recommended data for atomic, molecular and plasma-material interaction (A+M+PMI) processes in fusion research. The Unit organizes technical meetings and coordinates an A+M Data Centre Network (DCN) and a Code Centre Network (CCN). In addition the Unit organizes Coordinated Research Projects (CRPs), for which the objectives are mixed between development of new data and evaluation and recommendation of existing data. In the area of A+M data we are placing new emphasis in our meeting schedule on data evaluation and especially on uncertainties in calculated cross section data and the propagation of uncertainties through structure data and fundamental cross sections to effective rate coefficients. Following a recent meeting of the CCN it is intended to use electron scattering on Be, Ne and N2 as exemplars for study of uncertainties and uncertainty propagation in calculated data; this will be discussed further at the presentation. Please see http://www-amdis.iaea.org/CRP/ for more on our active and planned CRPs, which are concerned with atomic processes in core and edge plasma and with plasma interaction with beryllium-based surfaces and with irradiated tungsten.

The Case for Laboratory Developed Procedures

PubMed Central

Sabatini, Linda M.; Tsongalis, Gregory J.; Caliendo, Angela M.; Olsen, Randall J.; Ashwood, Edward R.; Bale, Sherri; Benirschke, Robert; Carlow, Dean; Funke, Birgit H.; Grody, Wayne W.; Hayden, Randall T.; Hegde, Madhuri; Lyon, Elaine; Pessin, Melissa; Press, Richard D.; Thomson, Richard B.

2017-01-01

An explosion of knowledge and technology is revolutionizing medicine and patient care. Novel testing must be brought to the clinic with safety and accuracy, but also in a timely and cost-effective manner, so that patients can benefit and laboratories can offer testing consistent with current guidelines. Under the oversight provided by the Clinical Laboratory Improvement Amendments, laboratories have been able to develop and optimize laboratory procedures for use in-house. Quality improvement programs, interlaboratory comparisons, and the ability of laboratories to adjust assays as needed to improve results, utilize new sample types, or incorporate new mutations, information, or technologies are positive aspects of Clinical Laboratory Improvement Amendments oversight of laboratory-developed procedures. Laboratories have a long history of successful service to patients operating under Clinical Laboratory Improvement Amendments. A series of detailed clinical examples illustrating the quality and positive impact of laboratory-developed procedures on patient care is provided. These examples also demonstrate how Clinical Laboratory Improvement Amendments oversight ensures accurate, reliable, and reproducible testing in clinical laboratories. PMID:28815200

NOTE: Monte Carlo simulation of correction factors for IAEA TLD holders

NASA Astrophysics Data System (ADS)

Hultqvist, Martha; Fernández-Varea, José M.; Izewska, Joanna

2010-03-01

The IAEA standard thermoluminescent dosimeter (TLD) holder has been developed for the IAEA/WHO TLD postal dose program for audits of high-energy photon beams, and it is also employed by the ESTRO-QUALity assurance network (EQUAL) and several national TLD audit networks. Factors correcting for the influence of the holder on the TL signal under reference conditions have been calculated in the present work from Monte Carlo simulations with the PENELOPE code for 60Co γ-rays and 4, 6, 10, 15, 18 and 25 MV photon beams. The simulation results are around 0.2% smaller than measured factors reported in the literature, but well within the combined standard uncertainties. The present study supports the use of the experimentally obtained holder correction factors in the determination of the absorbed dose to water from the TL readings; the factors calculated by means of Monte Carlo simulations may be adopted for the cases where there are no measured data.

Radionuclide transfer to fruit in the IAEA TRS No. 472

NASA Astrophysics Data System (ADS)

Carini, F.; Pellizzoni, M.; Giosuè, S.

2012-04-01

This paper describes the approach taken to present the information on fruits in the IAEA report TRS No. 472, supported by the IAEA-TECDOC-1616, which describes the key transfer processes, concepts and conceptual models regarded as important for dose assessment, as well as relevant parameters for modelling radionuclide transfer in fruits. Information relate to fruit plants grown in agricultural ecosystems of temperate regions. The relative significance of each pathway after release of radionuclides depends upon the radionuclide, the kind of crop, the stage of plant development and the season at time of deposition. Fruit intended as a component of the human diet is borne by plants that are heterogeneous in habits, and morphological and physiological traits. Information on radionuclides in fruit systems has therefore been rationalised by characterising plants in three groups: woody trees, shrubs, and herbaceous plants. Parameter values have been collected from open literature, conference proceedings, institutional reports, books and international databases. Data on root uptake are reported as transfer factor values related to fresh weight, being consumption data for fruits usually given in fresh weight.

Participation in proficiency test for tritium strontium and caesium isotopes in seawater 2015 (IAEA-RML-2015-02)

NASA Astrophysics Data System (ADS)

Visetpotjanakit, S.; Kaewpaluek, S.

2017-06-01

A proficiency test (PT) exercise has proposed by the International Atomic Energy Agency (IAEA) in the frame of the IAEA Technical Cooperation project RAS/7/021 “Marine benchmark study on the possible impact of the Fukushima radioactive releases in the Asia-Pacific Region for Caesium Determination in Sea Water” since 2012. In 2015 the exercise was referred to Proficiency Test for Tritium, Strontium and Caesium Isotopes in Seawater 2015 (IAEA-RML-2015-02) to analyse3H, 134Cs, 137Cs and90Sr in a seawater sample. OAP was one of the 17 laboratories from 15 countries from Asia-Pacific Region who joined the PT exercise. The aim of our participation was to validate our analytical performance for the accurate determination of radionuclides in seawater by developed methods of radiochemical analysis. OAP submitted results determining the concentration for the three elements i.e. 134Cs, 137Cs and90Sr in seawater to the IAEA. A critical review was made to check suitability of our methodology and the criteria for the accuracy, precision and trueness of our data. The results of both 134Cs and 137Cs passed all criteria which were assigned “Accepted” statuses. Whereas 90Sr analysis did not pass the accuracy test therefore it was considered as “Not accepted” Our results and all other participant results with critical comments were published in the IAEA proficiency test report.

Development of CMS monitoring procedures : technical summary.

DOT National Transportation Integrated Search

1998-04-01

This research study is concerned with the development of a set of procedures for monitoring congestion using GPS and GIS. These procedures are meant to be used more as a planning tool than for everyday traffic monitoring. Under this assumption, a ser...

IAEA programs in empowering the nuclear medicine profession through online educational resources.

PubMed

Pascual, Thomas Nb; Dondi, Maurizio; Paez, Diana; Kashyap, Ravi; Nunez-Miller, Rodolfo

2013-05-01

The International Atomic Energy Agency's (IAEA) programme in human health aims to enhance the capabilities in Member States to address needs related to the prevention, diagnosis, and treatment of diseases through the application of nuclear techniques. It has the specific mission of fostering the application of nuclear medicine techniques as part of the clinical management of certain types of diseases. Attuned to the continuous evolution of this specialty as well as to the advancement and diversity of methods in delivering capacity building efforts in this digital age, the section of nuclear medicine of the IAEA has enhanced its program by incorporating online educational resources for nuclear medicine professionals into its repertoire of projects to further its commitment in addressing the needs of its Member States in the field of nuclear medicine. Through online educational resources such as the Human Health Campus website, e-learning modules, and scheduled interactive webinars, a validation of the commitment by the IAEA in addressing the needs of its Member States in the field of nuclear medicine is strengthened while utilizing the advanced internet and communications technology which is progressively becoming available worldwide. The Human Health Campus (www.humanhealth.iaea.org) is the online educational resources initiative of the Division of Human Health of the IAEA geared toward enhancing professional knowledge of health professionals in radiation medicine (nuclear medicine and diagnostic imaging, radiation oncology, and medical radiation physics), and nutrition. E-learning modules provide an interactive learning environment to its users while providing immediate feedback for each task accomplished. Webinars, unlike webcasts, offer the opportunity of enhanced interaction with the learners facilitated through slide shows where the presenter guides and engages the audience using video and live streaming. This paper explores the IAEA's available online

Professor Glyn O. Phillip's legacy within the IAEA programme on radiation and tissue banking.

PubMed

Morales Pedraza, Jorge

2017-08-19

Professor Phillips began his involvement in the implementation of this important IAEA programme, insisting that there were advantages to be gained by using the ionizing radiation technique to sterilize human and animal tissues, based on the IAEA experience gained in the sterilization of medical products. The outcome of the implementation of the IAEA programme on radiation and tissue banking demonstrated that Professor Phillips was right in his opinion.

Assessment of Alternative Funding Mechanisms for the IAEA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Toomey, Christopher; Wyse, Evan T.; Kurzrok, Andrew J.

While the International Atomic Energy Agency (IAEA) has enjoyed substantial success and prestige in the international community, there is growing concern that global demographic trends, advances in technology and the trend towards austerity in Member State budgets will stretch the Agency’s resources to a point where it may no longer be possible to execute its multifaceted mission in its entirety. As part of an ongoing effort by the Next Generation Safeguards Initiative to evaluate the IAEA’s long-term budgetary concerns , this paper proposes a series of alternate funding mechanisms that have the potential to sustain the IAEA in the long-term,more » including endowment, charity, and fee-for-service funding models.« less

Development of FWD procedures manual.

DOT National Transportation Integrated Search

2010-04-01

In this project, the state-of-practice in FWD testing and analysis procedures were examined : by looking at the standard protocols of a number of other highway agencies. The specific : needs of NJDOT were also examined and a protocol was developed th...

Coordinated Research Projects of the IAEA Atomic and Molecular Data Unit

NASA Astrophysics Data System (ADS)

Braams, B. J.; Chung, H.-K.

2011-05-01

The IAEA Atomic and Molecular Data Unit is dedicated to the provision of databases for atomic, molecular and plasma-material interaction (AM/PMI) data that are relevant for nuclear fusion research. IAEA Coordinated Research Projects (CRPs) are the principal mechanism by which the Unit encourages data evaluation and the production of new data. Ongoing and planned CRPs on AM/PMI data are briefly described here.

International Conference on Advances in Radiation Oncology (ICARO): outcomes of an IAEA meeting.

PubMed

Salminen, Eeva K; Kiel, Krystyna; Ibbott, Geoffrey S; Joiner, Michael C; Rosenblatt, Eduardo; Zubizarreta, Eduardo; Wondergem, Jan; Meghzifene, Ahmed

2011-02-04

The IAEA held the International Conference on Advances in Radiation Oncology (ICARO) in Vienna on 27-29 April 2009. The Conference dealt with the issues and requirements posed by the transition from conventional radiotherapy to advanced modern technologies, including staffing, training, treatment planning and delivery, quality assurance (QA) and the optimal use of available resources. The current role of advanced technologies (defined as 3-dimensional and/or image guided treatment with photons or particles) in current clinical practice and future scenarios were discussed.ICARO was organized by the IAEA at the request of the Member States and co-sponsored and supported by other international organizations to assess advances in technologies in radiation oncology in the face of economic challenges that most countries confront. Participants submitted research contributions, which were reviewed by a scientific committee and presented via 46 lectures and 103 posters. There were 327 participants from 70 Member States as well as participants from industry and government. The ICARO meeting provided an independent forum for the interaction of participants from developed and developing countries on current and developing issues related to radiation oncology.

Analysis of IAEA Environmental Samples for Plutonium and Uranium by ICP/MS in Support Of International Safeguards

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farmer, Orville T.; Olsen, Khris B.; Thomas, May-Lin P.

2008-05-01

A method for the separation and determination of total and isotopic uranium and plutonium by ICP-MS was developed for IAEA samples on cellulose-based media. Preparation of the IAEA samples involved a series of redox chemistries and separations using TRU® resin (Eichrom). The sample introduction system, an APEX nebulizer (Elemental Scientific, Inc), provided enhanced nebulization for a several-fold increase in sensitivity and reduction in background. Application of mass bias (ALPHA) correction factors greatly improved the precision of the data. By combining the enhancements of chemical separation, instrumentation and data processing, detection levels for uranium and plutonium approached high attogram levels.

IAEA activities related to radiation biology and health effects of radiation.

PubMed

Wondergem, Jan; Rosenblatt, Eduardo

2012-03-01

The IAEA is involved in capacity building with regard to the radiobiological sciences in its member states through its technical cooperation programme. Research projects/programmes are normally carried out within the framework of coordinated research projects (CRPs). Under this programme, two CRPs have been approved which are relevant to nuclear/radiation accidents: (1) stem cell therapeutics to modify radiation-induced damage to normal tissue, and (2) strengthening biological dosimetry in IAEA member states.

Deterring Nuclear Proliferation: The Importance of IAEA Safeguards: A TEXTBOOK

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosenthal, M.D.; Fishbone, L.G.; Gallini, L.

2012-03-13

Nuclear terrorism and nuclear proliferation are among the most pressing challenges to international peace and security that we face today. Iran and Syria remain in non-compliance with the safeguards requirements of the NPT, and the nuclear ambitions of North Korea remain unchecked. Despite these challenges, the NPT remains a cornerstone of the nuclear non-proliferation regime, and the safeguards implemented by the International Atomic Energy Agency (IAEA) under the NPT play a critical role in deterring nuclear proliferation.How do they work? Where did they come from? And what is their future? This book answers these questions. Anyone studying the field ofmore » nuclear non-proliferation will benefit from reading this book, and for anyone entering the field, the book will enable them to get a running start. Part I describes the foundations of the international safeguards system: its origins in the 1930s - when new discoveries in physics made it clear immediately that nuclear energy held both peril and promise - through the entry into force in 1970 of the NPT, which codified the role of IAEA safeguards as a means to verify states NPT commitments not to acquire nuclear weapons. Part II describes the NPT safeguards system, which is based on a model safeguards agreement developed specifically for the NPT, The Structure and Content of Agreements between the Agency and States required in connection with the Treaty on the Non-Proliferation of Nuclear Weapons, which has been published by the IAEA as INFCIRC/153. Part III describes events, especially in South Africa, the DPRK, and Iraq in the early 1990s, that triggered a transformation in the way in which safeguards were conceptualized and implemented.« less

The IAEA neutron coincidence counting (INCC) and the DEMING least-squares fitting programs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krick, M.S.; Harker, W.C.; Rinard, P.M.

1998-12-01

Two computer programs are described: (1) the INCC (IAEA or International Neutron Coincidence Counting) program and (2) the DEMING curve-fitting program. The INCC program is an IAEA version of the Los Alamos NCC (Neutron Coincidence Counting) code. The DEMING program is an upgrade of earlier Windows{reg_sign} and DOS codes with the same name. The versions described are INCC 3.00 and DEMING 1.11. The INCC and DEMING codes provide inspectors with the software support needed to perform calibration and verification measurements with all of the neutron coincidence counting systems used in IAEA inspections for the nondestructive assay of plutonium and uranium.

Status of radiation protection in various interventional cardiology procedures in the Asia Pacific region

PubMed Central

Tsapaki, Virginia; Faruque Ghulam, Mohammed; Lim, Soo Teik; Ngo Minh, Hung; Nwe, Nwe; Sharma, Anil; Sim, Kui-Hian; Srimahachota, Suphot; Rehani, Madan Mohan

2011-01-01

Objective Increasing use of interventional procedures in cardiology with unknown levels of radiation protection in many countries of Asia-Pacific region necessitates the need for status assessment. The study was part of an International Atomic Energy Agency (IAEA) project for achieving improved radiation protection in interventional cardiology (IC) in developing countries. Design The survey covers 18 cardiac catheterisation laboratories in seven countries (Bangladesh, India, Malaysia, Myanmar, Singapore, Thailand and Vietnam). An important step was the creation of the ‘Asian network of Cardiologists in Radiation Protection’ and a newsletter. Data were collected on: radiation protection tools, number of IC laboratories, and annual number of various IC paediatric and adult procedures in the hospital and in the country. Patient radiation dose data were collected in terms of Kerma Area Product (KAP) and cumulative dose (CD). Results It is encouraging that protection devices for staff are largely used in the routine practice. Only 39% of the angiographic machines were equipped with a KAP meter. Operators' initial lack of awareness on radiation-protection optimisation improved significantly after participation in IAEA radiation-protection training. Only two out of five countries reporting patient percutaneous coronary intervention radiation-dose data were fully within the international guidance levels. Data from 51 patients who underwent multiple therapeutic procedures (median 2–3) indicated a total KAP reaching 995 Gy.cm2 (range 10.1–995) and CD 15.1 Gy (range 0.4–15.1), stressing the importance of dose monitoring and optimisation. Conclusions There is a need for interventional cardiology societies to play an active role in training actions and implementation of radiation protection. PMID:27325974

The evolution and impact of the International Atomic Energy Agency (IAEA) program on radiation and tissue banking in Asia and the Pacific region.

PubMed

Morales Pedraza, Jorge; Phillips, Glyn O

2009-05-01

The Asia and the Pacific region was within the IAEA program on radiation and tissue banking, the most active region. Most of the tissue banks in the Asia and the Pacific region were developed during the late 1980s and 1990s. The initial number of tissue banks established or supported by the IAEA program in the framework of the RCA Agreement for Asia and the Pacific region was 18. At the end of 2006, the number of tissue banks participating, in one way or another in the IAEA program was 59. Since the beginning of the implementation of the IAEA program in Asia and the Pacific region 63,537 amnion and 44,282 bone allografts were produced and 57,683 amnion and 36,388 bone allografts were used. The main impact of the IAEA program in the region was the following: the establishment or consolidation of at least 59 tissue banks in 15 countries in the region (the IAEA supported directly 16 of these banks); the improvement on the quality and safety of tissues procured and produced in the region reaching international standards; the implementation of eight national projects, two regional projects and two interregional projects; the elaboration of International Standards, a Code of Practice and a Public Awareness Strategies and, the application of quality control and quality assurances programs in all participating tissue banks.

Funding for the 2ND IAEA technical meeting on fusion data processing, validation and analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Greenwald, Martin

The International Atomic Energy Agency (IAEA) will organize the second Technical Meeting on Fusion Da Processing, Validation and Analysis from 30 May to 02 June, 2017, in Cambridge, MA USA. The meeting w be hosted by the MIT Plasma Science and Fusion Center (PSFC). The objective of the meeting is to provide a platform where a set of topics relevant to fusion data processing, validation and analysis are discussed with the view of extrapolation needs to next step fusion devices such as ITER. The validation and analysis of experimental data obtained from diagnostics used to characterize fusion plasmas are crucialmore » for a knowledge based understanding of the physical processes governing the dynamics of these plasmas. The meeting will aim at fostering, in particular, discussions of research and development results that set out or underline trends observed in the current major fusion confinement devices. General information on the IAEA, including its mission and organization, can be found at the IAEA websit Uncertainty quantification (UQ) Model selection, validation, and verification (V&V) Probability theory and statistical analysis Inverse problems & equilibrium reconstru ction Integrated data analysis Real time data analysis Machine learning Signal/image proc essing & pattern recognition Experimental design and synthetic diagnostics Data management« less

Antimicrobial Testing Methods & Procedures Developed by EPA's Microbiology Laboratory

EPA Pesticide Factsheets

We develop antimicrobial testing methods and standard operating procedures to measure the effectiveness of hard surface disinfectants against a variety of microorganisms. Find methods and procedures for antimicrobial testing.

INF and IAEA: A comparative analysis of verification strategy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scheinman, L.; Kratzer, M.

1992-07-01

This is the final report of a study on the relevance and possible lessons of Intermediate Range Nuclear Force (INF) verification to the International Atomic Energy Agency (IAEA) international safeguards activities.

Papers arising from IAEA Coordinated Research Project "Utilization of ion accelerators for studying and modelling of radiation induced defects in semiconductors and insulators" (F11016)

NASA Astrophysics Data System (ADS)

Vittone, Ettore; Breese, Mark; Simon, Aliz

2016-04-01

Within the International Atomic Energy Agency (IAEA) Department of Nuclear Sciences and Applications, activities are carried out to assist and advise IAEA Member States in assessing their needs for capacity building, research and development in nuclear sciences. Support is also provided to Member States' activities geared towards deriving benefits in fields such as (i) advanced materials for nuclear applications, (ii) application of accelerators and associated instrumentation, and (iii) nuclear, atomic and molecular data. One of the means that the IAEA uses to deliver its programme is Coordinated Research Projects (CRPs) which are very effective in stimulating international research and scientific interaction among the Member States.

IAEA coordinated research project on thermal-hydraulics of Supercritical Water-Cooled Reactors (SCWRs)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yamada, K.; Aksan, S. N.

The Supercritical Water-Cooled Reactor (SCWR) is an innovative water-cooled reactor concept, which uses supercritical pressure water as reactor coolant. It has been attracting interest of many researchers in various countries mainly due to its benefits of high thermal efficiency and simple primary systems, resulting in low capital cost. The IAEA started in 2008 a Coordinated Research Project (CRP) on Thermal-Hydraulics of SCWRs as a forum to foster the exchange of technical information and international collaboration in research and development. This paper summarizes the activities and current status of the CRP, as well as major progress achieved to date. At present,more » 15 institutions closely collaborate in several tasks. Some organizations have been conducting thermal-hydraulics experiments and analysing the data, and others have been participating in code-to-test and/or code-to-code benchmark exercises. The expected outputs of the CRP are also discussed. Finally, the paper introduces several IAEA activities relating to or arising from the CRP. (authors)« less

Calibrated sulfur isotope abundance ratios of three IAEA sulfur isotope reference materials and V-CDT with a reassessment of the atomic weight of sulfur

NASA Astrophysics Data System (ADS)

Ding, T.; Valkiers, S.; Kipphardt, H.; De Bièvre, P.; Taylor, P. D. P.; Gonfiantini, R.; Krouse, R.

2001-08-01

Calibrated values have been obtained for sulfur isotope abundance ratios of sulfur isotope reference materials distributed by the IAEA (Vienna). For the calibration of the measurements, a set of synthetic isotope mixtures were prepared gravimetrically from high purity Ag2S materials enriched in32S, 33S, and 34S. All materials were converted into SF6 gas and subsequently, their sulfur isotope ratios were measured on the SF5+ species using a special gas source mass spectrometer equipped with a molecular flow inlet system (IRMM's Avogadro II amount comparator). Values for the 32S/34S abundance ratios are 22.650 4(20), 22.142 4(20), and 23.393 3(17) for IAEA-S-1, IAEA-S-2, and IAEA-S-3, respectively. The calculated 32S/34S abundance ratio for V-CDT is 22.643 6(20), which is very close to the calibrated ratio obtained by Ding et al. (1999). In this way, the zero point of the VCDT scale is anchored firmly to the international system of units SI. The 32S/33S abundance ratios are 126.942(47), 125.473(55), 129.072(32), and 126.948(47) for IAEA-S-1, IAEA-S-2, IAEA-S-3, and V-CDT, respectively. In this way, the linearity of the V-CDT scale is improved over this range. The values of the sulfur molar mass for IAEA-S-1 and V-CDT were calculated to be 32.063 877(56) and 32.063 911(56), respectively, the values with the smallest combined uncertainty ever reported for the sulfur molar masses (atomic weights).

Use of fractional factorial design for optimization of digestion procedures followed by multi-element determination of essential and non-essential elements in nuts using ICP-OES technique.

PubMed

Momen, Awad A; Zachariadis, George A; Anthemidis, Aristidis N; Stratis, John A

2007-01-15

Two digestion procedures have been tested on nut samples for application in the determination of essential (Cr, Cu, Fe, Mg, Mn, Zn) and non-essential (Al, Ba, Cd, Pb) elements by inductively coupled plasma-optical emission spectrometry (ICP-OES). These included wet digestions with HNO(3)/H(2)SO(4) and HNO(3)/H(2)SO(4)/H(2)O(2). The later one is recommended for better analytes recoveries (relative error<11%). Two calibrations (aqueous standard and standard addition) procedures were studied and proved that standard addition was preferable for all analytes. Experimental designs for seven factors (HNO(3), H(2)SO(4) and H(2)O(2) volumes, digestion time, pre-digestion time, temperature of the hot plate and sample weight) were used for optimization of sample digestion procedures. For this purpose Plackett-Burman fractional factorial design, which involve eight experiments was adopted. The factors HNO(3) and H(2)O(2) volume, and the digestion time were found to be the most important parameters. The instrumental conditions were also optimized (using peanut matrix rather than aqueous standard solutions) considering radio-frequency (rf) incident power, nebulizer argon gas flow rate and sample uptake flow rate. The analytical performance, such as limits of detection (LOD<0.74mugg(-1)), precision of the overall procedures (relative standard deviation between 2.0 and 8.2%) and accuracy (relative errors between 0.4 and 11%) were assessed statistically to evaluate the developed analytical procedures. The good agreement between measured and certified values for all analytes (relative error <11%) with respect to IAEA-331 (spinach leaves) and IAEA-359 (cabbage) indicates that the developed analytical method is well suited for further studies on the fate of major elements in nuts and possibly similar matrices.

Seabed gamma-ray spectrometry: applications at IAEA-MEL.

PubMed

Osvath, I; Povinec, P P

2001-01-01

The technique of underwater gamma-ray spectrometry has been developed to complement or replace the traditional sampling-sample analysis approach for applications with space-time constraints, e.g. large areas of investigation, emergency response or long-term monitoring. IAEA-MEL has used both high-efficiency NaI(Tl) and high-resolution HPGe spectrometry to investigate contamination with anthropogenic radionuclides in a variety of marine environments. Surveys at the South Pacific nuclear test sites of Mururoa and Fangataufa have been used to guide sampling in areas of high contamination around ground zero points. In the Irish Sea offshore from the Sellafield nuclear reprocessing plant, a gamma-ray survey of seabed sediment was carried out to obtain estimates of the distribution and subsequently, for the inventory of 137Cs in the investigated area.

The 1998 Australian external beam radiotherapy survey and IAEA/WHO TLD postal dose quality audit.

PubMed

Huntley, R; Izewska, J

2000-03-01

The results of an updated Australian survey of external beam radiotherapy centres are presented. Most of the centres provided most of the requested information. The relative caseloads of various linear accelerator photon and electron beams have not changed significantly since the previous survey in 1995. The mean age of Australian LINACs is 7.1 years and that of other radiotherapy machines is 14.7 years. Every Australian radiotherapy centre participated in a special run of the IAEA/WHO TLD postal dose quality audit program, which was provided for Australian centres by the IAEA and WHO in May 1998. The dose quoted by the centres was in nearly every case within 1.5% of the dose assessed by the IAEA. This is within the combined standard uncertainty of the IAEA TLD service (1.8%). The results confirm the accuracy and precision of radiotherapy dosimetry in Australia and the adequate dissemination of the Australian standards from ARL (now ARPANSA) to the centres. The Australian standards have recently been shown to agree with those of other countries to within 0.25% by comparison with the BIPM.

Guidelines for the Development of Procedural Schematics for Research.

ERIC Educational Resources Information Center

Dolim, Michael P.

To aid the student or researcher in the development of an effective procedural schematic (a graphic description of a research plan showing the steps needed to reach a stated objective), guidelines are presented under three topic headings: Compositional elements, taxonomy of research terms, and examples of procedural schematics. An introduction…

An IAEA multi-technique X-ray spectrometry endstation at Elettra Sincrotrone Trieste: benchmarking results and interdisciplinary applications.

PubMed

Karydas, Andreas Germanos; Czyzycki, Mateusz; Leani, Juan José; Migliori, Alessandro; Osan, Janos; Bogovac, Mladen; Wrobel, Pawel; Vakula, Nikita; Padilla-Alvarez, Roman; Menk, Ralf Hendrik; Gol, Maryam Ghahremani; Antonelli, Matias; Tiwari, Manoj K; Caliri, Claudia; Vogel-Mikuš, Katarina; Darby, Iain; Kaiser, Ralf Bernd

2018-01-01

The International Atomic Energy Agency (IAEA) jointly with the Elettra Sincrotrone Trieste (EST) operates a multipurpose X-ray spectrometry endstation at the X-ray Fluorescence beamline (10.1L). The facility has been available to external users since the beginning of 2015 through the peer-review process of EST. Using this collaboration framework, the IAEA supports and promotes synchrotron-radiation-based research and training activities for various research groups from the IAEA Member States, especially those who have limited previous experience and resources to access a synchrotron radiation facility. This paper aims to provide a broad overview about various analytical capabilities, intrinsic features and performance figures of the IAEA X-ray spectrometry endstation through the measured results. The IAEA-EST endstation works with monochromatic X-rays in the energy range 3.7-14 keV for the Elettra storage ring operating at 2.0 or 2.4 GeV electron energy. It offers a combination of different advanced analytical probes, e.g. X-ray reflectivity, X-ray absorption fine-structure measurements, grazing-incidence X-ray fluorescence measurements, using different excitation and detection geometries, and thereby supports a comprehensive characterization for different kinds of nanostructured and bulk materials.

Development of a base mix design procedure.

DOT National Transportation Integrated Search

1974-01-01

This paper reports an investigation into the development of a compaction procedure for base mixes containing aggregates of 1 1/2" (38 mm) maximum size. The specimens were made in a manner similar to that given in ASTM Designation 1561-71, except that...

Testing the validity of the International Atomic Energy Agency (IAEA) safety culture model.

PubMed

López de Castro, Borja; Gracia, Francisco J; Peiró, José M; Pietrantoni, Luca; Hernández, Ana

2013-11-01

This paper takes the first steps to empirically validate the widely used model of safety culture of the International Atomic Energy Agency (IAEA), composed of five dimensions, further specified by 37 attributes. To do so, three independent and complementary studies are presented. First, 290 students serve to collect evidence about the face validity of the model. Second, 48 experts in organizational behavior judge its content validity. And third, 468 workers in a Spanish nuclear power plant help to reveal how closely the theoretical five-dimensional model can be replicated. Our findings suggest that several attributes of the model may not be related to their corresponding dimensions. According to our results, a one-dimensional structure fits the data better than the five dimensions proposed by the IAEA. Moreover, the IAEA model, as it stands, seems to have rather moderate content validity and low face validity. Practical implications for researchers and practitioners are included. Copyright © 2013 Elsevier Ltd. All rights reserved.

Task analysis method for procedural training curriculum development.

PubMed

Riggle, Jakeb D; Wadman, Michael C; McCrory, Bernadette; Lowndes, Bethany R; Heald, Elizabeth A; Carstens, Patricia K; Hallbeck, M Susan

2014-06-01

A central venous catheter (CVC) is an important medical tool used in critical care and emergent situations. Integral to proper care in many circumstances, insertion of a CVC introduces the risk of central line-associated blood stream infections and mechanical adverse events; proper training is important for safe CVC insertion. Cognitive task analysis (CTA) methods have been successfully implemented in the medical field to improve the training of postgraduate medical trainees, but can be very time-consuming to complete and require a significant time commitment from many subject matter experts (SMEs). Many medical procedures such as CVC insertion are linear processes with well-documented procedural steps. These linear procedures may not require a traditional CTA to gather the information necessary to create a training curriculum. Accordingly, a novel, streamlined CTA method designed primarily to collect cognitive cues for linear procedures was developed to be used by medical professionals with minimal CTA training. This new CTA methodology required fewer trained personnel, fewer interview sessions, and less time commitment from SMEs than a traditional CTA. Based on this study, a streamlined CTA methodology can be used to efficiently gather cognitive information on linear medical procedures for the creation of resident training curricula and procedural skills assessments.

Developing Conceptual Understanding and Procedural Skill in Mathematics: An Iterative Process.

ERIC Educational Resources Information Center

Rittle-Johnson, Bethany; Siegler, Robert S.; Alibali, Martha Wagner

2001-01-01

Proposes that conceptual and procedural knowledge develop in an iterative fashion and improved problem representation is one mechanism underlying the relations between them. Two experiments were conducted with 5th and 6th grade students learning about decimal fractions. Results indicate conceptual and procedural knowledge do develop, iteratively,…

The Mailbox Computer System for the IAEA verification experiment on HEU downlending at the Portsmouth Gaseous Diffusion Plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aronson, A.L.; Gordon, D.M.

IN APRIL 1996, THE UNITED STATES (US) ADDED THE PORTSMOUTH GASEOUS DIFFUSION PLANT TO THE LIST OF FACILITIES ELIGIBLE FOR THE APPLICATION OF INTERNATIONAL ATOMIC ENERGY AGENCY (IAEA) SAFEGUARDS. AT THAT TIME, THE US PROPOSED THAT THE IAEA CARRY OUT A ''VERIFICATION EXPERIMENT'' AT THE PLANT WITH RESPECT TO DOOWNBLENDING OF ABOUT 13 METRIC TONS OF HIGHLY ENRICHED URANIUM (HEU) IN THE FORM OF URANIUM HEXAFLUROIDE (UF6). DURING THE PERIOD DECEMBER 1997 THROUGH JULY 1998, THE IAEA CARRIED OUT THE REQUESTED VERIFICATION EXPERIMENT. THE VERIFICATION APPROACH USED FOR THIS EXPERIMENT INCLUDED, AMONG OTHER MEASURES, THE ENTRY OF PROCESS-OPERATIONAL DATA BYmore » THE FACILITY OPERATOR ON A NEAR-REAL-TIME BASIS INTO A ''MAILBOX'' COMPUTER LOCATED WITHIN A TAMPER-INDICATING ENCLOSURE SEALED BY THE IAEA.« less

Absolute dose determination in high-energy electron beams: Comparison of IAEA dosimetry protocols

PubMed Central

Sathiyan, S.; Ravikumar, M.

2008-01-01

In this study, absorbed doses were measured and compared for high-energy electrons (6, 9, 12, 16, and 20 MeV) using International Atomic Energy Agency (IAEA), Technical Reports Series No. 277 (TRS), TRS 381, and TRS 398 dosimetry protocols. Absolute dose measurements were carried out using FC65-G Farmer chamber and Nordic Association of Clinical Physicists (NACP) parallel plate chamber with DOSE1 electrometer in WP1-D water phantom for reference field size of 15 × 15 cm2 at 100 cm source-to-surface distance. The results show that the difference between TRS 398 and TRS 381 was about 0.24% to 1.3% depending upon the energy, and the maximum difference between TRS 398 and TRS 277 was 1.5%. The use of cylindrical chamber in electron beam gives the maximum dose difference between the TRS 398 and TRS 277 in the order of 1.4% for energies above 10 MeV (R50 > 4 g/cm2). It was observed that the accuracy of dose estimation was better with the protocols based on the water calibration procedures, as no conversion quantities are involved for conversion of dose from air to water. The cross-calibration procedure of parallel plate chamber with high-energy electron beams is recommended as it avoids pwall correction factor entering into the determination of kQ,Qo. PMID:19893700

INF and IAEA: A comparative analysis of verification strategy. [Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scheinman, L.; Kratzer, M.

1992-07-01

This is the final report of a study on the relevance and possible lessons of Intermediate Range Nuclear Force (INF) verification to the International Atomic Energy Agency (IAEA) international safeguards activities.

Development of an improved overlay design procedure for Oregon : volume II, evaluation of procedure.

DOT National Transportation Integrated Search

1987-12-01

This report is the second in a three-volume series dealing with the development of an improved overlay design procedure for Oregon. This report presents the results of the second-year findings. Data from five projects were collected and analyzed usin...

δ15N measurement of organic and inorganic substances by EA-IRMS: a speciation-dependent procedure.

PubMed

Gentile, Natacha; Rossi, Michel J; Delémont, Olivier; Siegwolf, Rolf T W

2013-01-01

Little attention has been paid so far to the influence of the chemical nature of the substance when measuring δ(15)N by elemental analysis (EA)-isotope ratio mass spectrometry (IRMS). Although the bulk nitrogen isotope analysis of organic material is not to be questioned, literature from different disciplines using IRMS provides hints that the quantitative conversion of nitrate into nitrogen presents difficulties. We observed abnormal series of δ(15)N values of laboratory standards and nitrates. These unexpected results were shown to be related to the tailing of the nitrogen peak of nitrate-containing compounds. A series of experiments were set up to investigate the cause of this phenomenon, using ammonium nitrate (NH(4)NO(3)) and potassium nitrate (KNO(3)) samples, two organic laboratory standards as well as the international secondary reference materials IAEA-N1, IAEA-N2-two ammonium sulphates [(NH(4))(2)SO(4)]-and IAEA-NO-3, a potassium nitrate. In experiment 1, we used graphite and vanadium pentoxide (V(2)O(5)) as additives to observe if they could enhance the decomposition (combustion) of nitrates. In experiment 2, we tested another elemental analyser configuration including an additional section of reduced copper in order to see whether or not the tailing could originate from an incomplete reduction process. Finally, we modified several parameters of the method and observed their influence on the peak shape, δ(15)N value and nitrogen content in weight percent of nitrogen of the target substances. We found the best results using mere thermal decomposition in helium, under exclusion of any oxygen. We show that the analytical procedure used for organic samples should not be used for nitrates because of their different chemical nature. We present the best performance given one set of sample introduction parameters for the analysis of nitrates, as well as for the ammonium sulphate IAEA-N1 and IAEA-N2 reference materials. We discuss these results considering the

The impact of the International Atomic Energy Agency (IAEA) program on radiation and tissue banking in Argentina.

PubMed

Kairiyama, Eulogia; Morales Pedraza, Jorge

2009-05-01

Tissue banking activities in Argentina started in 1993. The regulatory and controlling national authority on organ, tissue and cells for transplantation activity is the National Unique Coordinating Central Institute for Ablation and Implant (INCUCAI). Three tissue banks were established under the IAEA program and nine other banks participated actively in the implementation of this program. As result of the implementation of the IAEA program in Argentina and the work done by the established tissue banks, more and more hospitals are now using, in a routine manner, radiation sterilised tissues processed by these banks. During the period 1992-2005, more than 21 016 tissues were produced and irradiated in the tissue banks participating in the IAEA program. Within the framework of the training component of the IAEA program, Argentina has been selected to host the Regional Training Centre for Latin American. In this centre, tissue bank operators and medical personal from Latin American countries were trained. Since 1999, Argentina has organised four regular regional training courses and two virtual regional training courses. More than twenty (20) tissue bank operators and medical personnel from Argentina were trained under the IAEA program in the six courses organised in the country. In general, ninety (96) tissue bank operators and medical personnel from eight Latin-American countries were trained in the Buenos Aires regional training centre. From Argentina 16 students graduated in these courses.

Development of an algorithm to plan and simulate a new interventional procedure.

PubMed

Fujita, Buntaro; Kütting, Maximilian; Scholtz, Smita; Utzenrath, Marc; Hakim-Meibodi, Kavous; Paluszkiewicz, Lech; Schmitz, Christoph; Börgermann, Jochen; Gummert, Jan; Steinseifer, Ulrich; Ensminger, Stephan

2015-07-01

The number of implanted biological valves for treatment of valvular heart disease is growing and a percentage of these patients will eventually undergo a transcatheter valve-in-valve (ViV) procedure. Some of these patients will represent challenging cases. The aim of this study was to develop a feasible algorithm to plan and in vitro simulate a new interventional procedure to improve patient outcome. In addition to standard diagnostic routine, our algorithm includes 3D printing of the annulus, hydrodynamic measurements and high-speed analysis of leaflet kinematics after simulation of the procedure in different prosthesis positions as well as X-ray imaging of the most suitable valve position to create a 'blueprint' for the patient procedure. This algorithm was developed for a patient with a degenerated Perceval aortic sutureless prosthesis requiring a ViV procedure. Different ViV procedures were assessed in the algorithm and based on these results the best option for the patient was chosen. The actual procedure went exactly as planned with help of this algorithm. Here we have developed a new technically feasible algorithm simulating important aspects of a novel interventional procedure prior to the actual procedure. This algorithm can be applied to virtually all patients requiring a novel interventional procedure to help identify risks and find optimal parameters for prosthesis selection and placement in order to maximize safety for the patient. © The Author 2015. Published by Oxford University Press on behalf of the European Association for Cardio-Thoracic Surgery. All rights reserved.

Training in Tbilisi nuclear facility provides new sampling perspectives for IAEA inspectors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brim, Cornelia P.

2016-06-08

Office of Nonproliferation and Arms Control- (NPAC-) sponsored training in a “cold” nuclear facility in Tbilisi, Georgia provides International Atomic Energy Agency (IAEA) inspectors with a new perspective on environmental sampling strategies. Sponsored by the Nuclear Safeguards program under the NPAC, Pacific Northwest National Laboratory (PNNL) experts have been conducting an annual weeklong class for IAEA inspectors in a closed nuclear facility since 2011. The Andronikashvili Institute of Physics and the Republic of Georgia collaborate with PNNL to provide the training, and the U.S. Department of State, the U.S. Embassy in Tbilisi and the U.S. Mission to International Organizations inmore » Vienna provide logistical support.« less

Approach to training of personnel to manage radioactive wastes offered by education training Centre at Moscow Sia Radon under sponsorship of IAEA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Batyukhnova, O.G.; Dmitriev, S.A.; Ojovan, M.I.

The availability of qualified personnel is crucial to the licensing and efficient and safe operation of waste management facilities and for the improvement of the existing waste management practices. The countries with some degree of waste management activities are of special concerns, since their narrow waste management experience and personal capabilities may be a limiting factor to manage radioactive waste in a safe and technically optimal manner. The International Education Training Centre (IETC) at Moscow State Unitary Enterprise Scientific and Industrial Association 'Radon' (SIA 'Radon'), in co-operation with the International Atomic Energy Agency (IAEA), has developed expertise and provided trainingmore » to waste management personnel for the last 10 years. During this period, more than 300 specialists from 26 European and Asian countries, (mostly) sponsored by the IAEA, have increased their knowledge and skills in radioactive waste management. The current experience of the SIA 'Radon' in the organisation of the IAEA sponsored training is summarized and an outline of some strategic educational elements, which IETC will continue to pursue in the coming years, is provided. (authors)« less

Radiation processing of natural polymers: The IAEA contribution

NASA Astrophysics Data System (ADS)

Haji-Saeid, Mohammad; Safrany, Agnes; Sampa, Maria Helena de O.; Ramamoorthy, Natesan

2010-03-01

Radiation processing offers a clean and additive-free method for preparation of value-added novel materials based on renewable, non-toxic, and biodegradable natural polymers. Crosslinked natural polymers can be used as hydrogel wound dressings, face cleaning cosmetic masks, adsorbents of toxins, and non-bedsore mats; while low molecular weight products show antibiotic, antioxidant, and plant-growth promoting properties. Recognizing the potential benefits that radiation technology can offer for processing of natural polymers into useful products, the IAEA implemented a coordinated research project (CRP) on "Development of Radiation-processed products of Natural Polymers for application in Agriculture, Healthcare, Industry and Environment". This CRP was launched at the end of 2007 with participation of 16 MS to help connecting radiation technology and end-users to derive enhanced benefits from these new value-added products of radiation-processed natural materials. In this paper the results of activities in participating MS related to this work will be presented.

Advanced crew procedures development techniques: Procedures and performance program description

NASA Technical Reports Server (NTRS)

Arbet, J. D.; Mangiaracina, A. A.

1975-01-01

The Procedures and Performance Program (PPP) for operation in conjunction with the Shuttle Procedures Simulator (SPS) is described. The PPP user interface, the SPS/PPP interface, and the PPP applications software are discussed.

TU-AB-BRC-07: Efficiency of An IAEA Phase-Space Source for a Low Energy X-Ray Tube Using Egs++

DOE Office of Scientific and Technical Information (OSTI.GOV)

Watson, PGF; Renaud, MA; Seuntjens, J

Purpose: To extend the capability of the EGSnrc C++ class library (egs++) to write and read IAEA phase-space files as a particle source, and to assess the relative efficiency gain in dose calculation using an IAEA phase-space source for modelling a miniature low energy x-ray source. Methods: We created a new ausgab object to score particles exiting a user-defined geometry and write them to an IAEA phase-space file. A new particle source was created to read from IAEA phase-space data. With these tools, a phase-space file was generated for particles exiting a miniature 50 kVp x-ray tube (The INTRABEAM System,more » Carl Zeiss). The phase-space source was validated by comparing calculated PDDs with a full electron source simulation of the INTRABEAM. The dose calculation efficiency gain of the phase-space source was determined relative to the full simulation. The efficiency gain as a function of i) depth in water, and ii) job parallelization was investigated. Results: The phase-space and electron source PDDs were found to agree to 0.5% RMS, comparable to statistical uncertainties. The use of a phase-space source for the INTRABEAM led to a relative efficiency gain of greater than 20 over the full electron source simulation, with an increase of up to a factor of 196. The efficiency gain was found to decrease with depth in water, due to the influence of scattering. Job parallelization (across 2 to 256 cores) was not found to have any detrimental effect on efficiency gain. Conclusion: A set of tools has been developed for writing and reading IAEA phase-space files, which can be used with any egs++ user code. For simulation of a low energy x-ray tube, the use of a phase-space source was found to increase the relative dose calculation efficiency by factor of up to 196. The authors acknowledge partial support by the CREATE Medical Physics Research Training Network grant of the Natural Sciences and Engineering Research Council (Grant No. 432290).« less

International contributions to IAEA-NEA heat transfer databases for supercritical fluids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leung, L. K. H.; Yamada, K.

2012-07-01

An IAEA Coordinated Research Project on 'Heat Transfer Behaviour and Thermohydraulics Code Testing for SCWRs' is being conducted to facilitate collaboration and interaction among participants from 15 organizations. While the project covers several key technology areas relevant to the development of SCWR concepts, it focuses mainly on the heat transfer aspect, which has been identified as the most challenging. Through the collaborating effort, large heat-transfer databases have been compiled for supercritical water and surrogate fluids in tubes, annuli, and bundle subassemblies of various orientations over a wide range of flow conditions. Assessments of several supercritical heat-transfer correlations were performed usingmore » the complied databases. The assessment results are presented. (authors)« less

Library Collections Development and Maintenance Policies and Procedures Manual.

ERIC Educational Resources Information Center

Tubesing, Richard

This manual for the College of the Southwest (New Mexico) library delineates collection development policies and procedures for library and teaching faculty. The first section deals with collection development and maintenance responsibilities: knowledge of the collection; knowledge of college and course needs; library materials budget allocations;…

Trip report on IAEA Training Workshop on Implementation of Integrated Management Systems for Research Reactors (T3-TR-45496).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pratt, Richard J.

2013-11-01

From 17-21 June 2013, Sandia National Laboratories, Technical Area-V (SNL TA-V) represented the United States Department of Energy/National Nuclear Security Administration (DOE/NNSA) at the International Atomic Energy Agency (IAEA) Training Workshop (T3-TR-45486). This report gives a breakdown of the IAEA regulatory structure for those unfamiliar, and the lessons learned and observations that apply to SNL TA-V that were obtained from the workshop. The Safety Report Series, IAEA workshop final report, and SNL TA-V presentation are included as attachments.

Evaluating the performance of two neutron spectrum unfolding codes based on iterative procedures and artificial neural networks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ortiz-Rodriguez, J. M.; Reyes Alfaro, A.; Reyes Haro, A.

In this work the performance of two neutron spectrum unfolding codes based on iterative procedures and artificial neural networks is evaluated. The first one code based on traditional iterative procedures and called Neutron spectrometry and dosimetry from the Universidad Autonoma de Zacatecas (NSDUAZ) use the SPUNIT iterative algorithm and was designed to unfold neutron spectrum and calculate 15 dosimetric quantities and 7 IAEA survey meters. The main feature of this code is the automated selection of the initial guess spectrum trough a compendium of neutron spectrum compiled by the IAEA. The second one code known as Neutron spectrometry and dosimetrymore » with artificial neural networks (NDSann) is a code designed using neural nets technology. The artificial intelligence approach of neural net does not solve mathematical equations. By using the knowledge stored at synaptic weights on a neural net properly trained, the code is capable to unfold neutron spectrum and to simultaneously calculate 15 dosimetric quantities, needing as entrance data, only the rate counts measured with a Bonner spheres system. Similarities of both NSDUAZ and NSDann codes are: they follow the same easy and intuitive user's philosophy and were designed in a graphical interface under the LabVIEW programming environment. Both codes unfold the neutron spectrum expressed in 60 energy bins, calculate 15 dosimetric quantities and generate a full report in HTML format. Differences of these codes are: NSDUAZ code was designed using classical iterative approaches and needs an initial guess spectrum in order to initiate the iterative procedure. In NSDUAZ, a programming routine was designed to calculate 7 IAEA instrument survey meters using the fluence-dose conversion coefficients. NSDann code use artificial neural networks for solving the ill-conditioned equation system of neutron spectrometry problem through synaptic weights of a properly trained neural network. Contrary to iterative procedures

Evaluating the performance of two neutron spectrum unfolding codes based on iterative procedures and artificial neural networks

NASA Astrophysics Data System (ADS)

Ortiz-Rodríguez, J. M.; Reyes Alfaro, A.; Reyes Haro, A.; Solís Sánches, L. O.; Miranda, R. Castañeda; Cervantes Viramontes, J. M.; Vega-Carrillo, H. R.

2013-07-01

In this work the performance of two neutron spectrum unfolding codes based on iterative procedures and artificial neural networks is evaluated. The first one code based on traditional iterative procedures and called Neutron spectrometry and dosimetry from the Universidad Autonoma de Zacatecas (NSDUAZ) use the SPUNIT iterative algorithm and was designed to unfold neutron spectrum and calculate 15 dosimetric quantities and 7 IAEA survey meters. The main feature of this code is the automated selection of the initial guess spectrum trough a compendium of neutron spectrum compiled by the IAEA. The second one code known as Neutron spectrometry and dosimetry with artificial neural networks (NDSann) is a code designed using neural nets technology. The artificial intelligence approach of neural net does not solve mathematical equations. By using the knowledge stored at synaptic weights on a neural net properly trained, the code is capable to unfold neutron spectrum and to simultaneously calculate 15 dosimetric quantities, needing as entrance data, only the rate counts measured with a Bonner spheres system. Similarities of both NSDUAZ and NSDann codes are: they follow the same easy and intuitive user's philosophy and were designed in a graphical interface under the LabVIEW programming environment. Both codes unfold the neutron spectrum expressed in 60 energy bins, calculate 15 dosimetric quantities and generate a full report in HTML format. Differences of these codes are: NSDUAZ code was designed using classical iterative approaches and needs an initial guess spectrum in order to initiate the iterative procedure. In NSDUAZ, a programming routine was designed to calculate 7 IAEA instrument survey meters using the fluence-dose conversion coefficients. NSDann code use artificial neural networks for solving the ill-conditioned equation system of neutron spectrometry problem through synaptic weights of a properly trained neural network. Contrary to iterative procedures, in neural

Development of use of an Operational Procedure Information System (OPIS) for future space missions

NASA Technical Reports Server (NTRS)

Illmer, N.; Mies, L.; Schoen, A.; Jain, A.

1994-01-01

A MS-Windows based electronic procedure system, called OPIS (Operational Procedure Information System), was developed. The system consists of two parts, the editor, for 'writing' the procedure and the notepad application, for the usage of the procedures by the crew during training and flight. The system is based on standardized, structured procedure format and language. It allows the embedding of sketches, photos, animated graphics and video sequences and the access to off-nominal procedures by linkage to an appropriate database. The system facilitates the work with procedures of different degrees of detail, depending on the training status of the crew. The development of a 'language module' for the automatic translation of the procedures, for example into Russian, is planned.

From innovation to standard practice: Developing and disseminating behavioral procedures

PubMed Central

Paine, Stan C.; Bellamy, G. Thomas

1982-01-01

This paper proposes a three-stage continuum for discussing the development and dissemination of behavioral technology. At the level of behavioral techniques, researchers need only establish a functional relationship between technologically defined intervention procedures and socially significant target behaviors. Dissemination is conducted for informational purposes only, and the purposes and details surrounding subsequent use of the technique are left to the discretion of the user. At the level of behavioral demonstration, a collection of socially acceptable intervention procedures is refined and standardized and must be shown to produce behavior changes across a number of subjects. Here dissemination is conducted, in large part, to generate support for provision of services. At the level of behavioral models, procedural descriptions must be useroriented. Additionally, model effects must be obtainable by agents not associated with their development and must compare favorably with other treatment or service alternatives. The purpose of dissemination at this level is to obtain adoptions and replications of the model. Details of development and dissemination of behavioral technology at each of these three levels are discussed. PMID:22478555

Safety in the Chemical Laboratory: Developing Departmental Safety Procedures.

ERIC Educational Resources Information Center

Renfrew, Malcolm M., Ed.; Palladino, George F.

1980-01-01

Presents rationale and guidelines for development of Safety Standard Operating Procedures (Safety SOP) specific for local conditions. Includes an outline of a Safety SOP developed for a department primarily focused on undergraduate education with a wide variety of expertise from common laborer to PhD with 20 years experience. (Author/JN)

Validating dose rate calibration of radiotherapy photon beams through IAEA/WHO postal audit dosimetry service.

PubMed

Jangda, Abdul Qadir; Hussein, Sherali

2012-05-01

In external beam radiation therapy (EBRT), the quality assurance (QA) of the radiation beam is crucial to the accurate delivery of the prescribed dose to the patient. One of the dosimetric parameters that require monitoring is the beam output, specified as the dose rate on the central axis under reference conditions. The aim of this project was to validate dose rate calibration of megavoltage photon beams using the International Atomic Energy Agency (IAEA)/World Health Organisation (WHO) postal audit dosimetry service. Three photon beams were audited: a 6 MV beam from the low-energy linac and 6 and 18 MV beams from a dual high-energy linac. The agreement between our stated doses and the IAEA results was within 1% for the two 6 MV beams and within 2% for the 18 MV beam. The IAEA/WHO postal audit dosimetry service provides an independent verification of dose rate calibration protocol by an international facility.

Strengthened IAEA Safeguards-Imagery Analysis: Geospatial Tools for Nonproliferation Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pabian, Frank V

2012-08-14

This slide presentation focuses on the growing role and importance of imagery analysis for IAEA safeguards applications and how commercial satellite imagery, together with the newly available geospatial tools, can be used to promote 'all-source synergy.' As additional sources of openly available information, satellite imagery in conjunction with the geospatial tools can be used to significantly augment and enhance existing information gathering techniques, procedures, and analyses in the remote detection and assessment of nonproliferation relevant activities, facilities, and programs. Foremost of the geospatial tools are the 'Digital Virtual Globes' (i.e., GoogleEarth, Virtual Earth, etc.) that are far better than previouslymore » used simple 2-D plan-view line drawings for visualization of known and suspected facilities of interest which can be critical to: (1) Site familiarization and true geospatial context awareness; (2) Pre-inspection planning; (3) Onsite orientation and navigation; (4) Post-inspection reporting; (5) Site monitoring over time for changes; (6) Verification of states site declarations and for input to State Evaluation reports; and (7) A common basis for discussions among all interested parties (Member States). Additionally, as an 'open-source', such virtual globes can also provide a new, essentially free, means to conduct broad area search for undeclared nuclear sites and activities - either alleged through open source leads; identified on internet BLOGS and WIKI Layers, with input from a 'free' cadre of global browsers and/or by knowledgeable local citizens (a.k.a.: 'crowdsourcing'), that can include ground photos and maps; or by other initiatives based on existing information and in-house country knowledge. They also provide a means to acquire ground photography taken by locals, hobbyists, and tourists of the surrounding locales that can be useful in identifying and discriminating between relevant and non-relevant facilities and their

Developing Competency in Payroll Procedures

ERIC Educational Resources Information Center

Jackson, Allen L.

1975-01-01

The author describes a sequence of units that provides for competency in payroll procedures. The units could be the basis for a four to six week minicourse and are adaptable, so that the student, upon completion, will be able to apply his learning to any payroll procedures system. (Author/AJ)

Development of an improved overlay procedure for Oregon : volume III, field manual.

DOT National Transportation Integrated Search

1987-12-01

This report is the third in a three-volume series dealing with the development of an improved overlay design procedure for Oregon. This report presents technical guidelines for using the proposed overlay design procedure. Four areas are described, in...

Development and Applications of a Stage Stacking Procedure

NASA Technical Reports Server (NTRS)

Kulkarni, Sameer; Celestina, Mark L.; Adamczyk, John J.

2012-01-01

The preliminary design of multistage axial compressors in gas turbine engines is typically accomplished with mean-line methods. These methods, which rely on empirical correlations, estimate compressor performance well near the design point, but may become less reliable off-design. For land-based applications of gas turbine engines, off-design performance estimates are becoming increasingly important, as turbine plant operators desire peaking or load-following capabilities and hot-day operability. The current work develops a one-dimensional stage stacking procedure, including a newly defined blockage term, which is used to estimate the off-design performance and operability range of a 13-stage axial compressor used in a power generating gas turbine engine. The new blockage term is defined to give mathematical closure on static pressure, and values of blockage are shown to collapse to curves as a function of stage inlet flow coefficient and corrected shaft speed. In addition to these blockage curves, the stage stacking procedure utilizes stage characteristics of ideal work coefficient and adiabatic efficiency. These curves are constructed using flow information extracted from computational fluid dynamics (CFD) simulations of groups of stages within the compressor. Performance estimates resulting from the stage stacking procedure are shown to match the results of CFD simulations of the entire compressor to within 1.6% in overall total pressure ratio and within 0.3 points in overall adiabatic efficiency. Utility of the stage stacking procedure is demonstrated by estimation of the minimum corrected speed which allows stable operation of the compressor. Further utility of the stage stacking procedure is demonstrated with a bleed sensitivity study, which estimates a bleed schedule to expand the compressors operating range.

Developing a Procedures Manual for Using the Innovacq 100 System Effectively and Efficiently.

ERIC Educational Resources Information Center

Cubberley, Carol

The installation of an automated acquisitions system, the Innovacq 100, demanded a review and revision of procedures in the Acquisitions Department of the University of Central Florida Library. This practicum report describes the process involved in developing the new procedures. Prior to installation, the old departmental procedures manual and…

Development of a patient-specific surgical simulator for pediatric laparoscopic procedures.

PubMed

Saber, Nikoo R; Menon, Vinay; St-Pierre, Jean C; Looi, Thomas; Drake, James M; Cyril, Xavier

2014-01-01

The purpose of this study is to develop and evaluate a pediatric patient-specific surgical simulator for the planning, practice, and validation of laparoscopic surgical procedures prior to intervention, initially focusing on the choledochal cyst resection and reconstruction scenario. The simulator is comprised of software elements including a deformable body physics engine, virtual surgical tools, and abdominal organs. Hardware components such as haptics-enabled hand controllers and a representative endoscopic tool have also been integrated. The prototype is able to perform a number of surgical tasks and further development work is under way to simulate the complete procedure with acceptable fidelity and accuracy.

34 CFR 303.342 - Procedures for IFSP development, review, and evaluation.

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROGRAM FOR INFANTS AND TODDLERS WITH DISABILITIES Child Find, Evaluations and Assessments, and... development, review, and evaluation. (a) Meeting to develop initial IFSP—timelines. For a child referred to... 34 Education 2 2014-07-01 2013-07-01 true Procedures for IFSP development, review, and evaluation...

34 CFR 303.342 - Procedures for IFSP development, review, and evaluation.

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROGRAM FOR INFANTS AND TODDLERS WITH DISABILITIES Child Find, Evaluations and Assessments, and... development, review, and evaluation. (a) Meeting to develop initial IFSP—timelines. For a child referred to... 34 Education 2 2013-07-01 2013-07-01 false Procedures for IFSP development, review, and evaluation...

34 CFR 303.342 - Procedures for IFSP development, review, and evaluation.

Code of Federal Regulations, 2012 CFR

2012-07-01

... PROGRAM FOR INFANTS AND TODDLERS WITH DISABILITIES Child Find, Evaluations and Assessments, and... development, review, and evaluation. (a) Meeting to develop initial IFSP—timelines. For a child referred to... 34 Education 2 2012-07-01 2012-07-01 false Procedures for IFSP development, review, and evaluation...

Product assurance policies and procedures for flight dynamics software development

NASA Technical Reports Server (NTRS)

Perry, Sandra; Jordan, Leon; Decker, William; Page, Gerald; Mcgarry, Frank E.; Valett, Jon

1987-01-01

The product assurance policies and procedures necessary to support flight dynamics software development projects for Goddard Space Flight Center are presented. The quality assurance and configuration management methods and tools for each phase of the software development life cycles are described, from requirements analysis through acceptance testing; maintenance and operation are not addressed.

Numerical modeling of the radionuclide water pathway with HYDRUS and comparison with the IAEA model of SR 44.

PubMed

Merk, Rainer

2012-02-01

This study depicts a theoretical experiment in which the radionuclide transport through the porous material of a landfill consisting of concrete rubble (e.g., from the decommissioning of nuclear power plants) and the subsequent migration through the vadose zone and aquifer to a model well is calculated by means of the software HYDRUS-1D (Simunek et al., 2008). The radionuclides originally contained within the rubble become dissolved due to leaching caused by infiltrated rainwater. The resulting well-water contamination (in Bq/L) is calculated numerically as a function of time and location and compared with the outcome of a simplified analytic model for the groundwater pathway published by the IAEA (2005). Identical model parameters are considered. The main objective of the present work is to evaluate the predictive capacity of the more simple IAEA model using HYDRUS-1D as a reference. For most of the radionuclides considered (e.g., ¹²⁹I, and ²³⁹Pu), results from applying the IAEA model were found to be comparable to results from the more elaborate HYDRUS modeling, provided the underlying parameter values are comparable. However, the IAEA model appears to underestimate the effects resulting from, for example, high nuclide mobility, short half-life, or short-term variations in the water infiltration. The present results indicate that the IAEA model is suited for screening calculations and general recommendation purposes. However, the analysis of a specific site should be accompanied by detailed HYDRUS computer simulations. In all models considered, the calculation outcome largely depends on the choice of the sorption parameter K(d). Copyright © 2011 Elsevier Ltd. All rights reserved.

Moving template analysis of crack growth. 1: Procedure development

NASA Astrophysics Data System (ADS)

Padovan, Joe; Guo, Y. H.

1994-06-01

Based on a moving template procedure, this two part series will develop a method to follow the crack tip physics in a self-adaptive manner which provides a uniformly accurate prediction of crack growth. For multiple crack environments, this is achieved by attaching a moving template to each crack tip. The templates are each individually oriented to follow the associated growth orientation and rate. In this part, the essentials of the procedure are derived for application to fatigue crack environments. Overall the scheme derived possesses several hierarchical levels, i.e. the global model, the interpolatively tied moving template, and a multilevel element death option to simulate the crack wake. To speed up computation, the hierarchical polytree scheme is used to reorganize the global stiffness inversion process. In addition to developing the various features of the scheme, the accuracy of predictions for various crack lengths is also benchmarked. Part 2 extends the scheme to multiple crack problems. Extensive benchmarking is also presented to verify the scheme.

A Procedure for Measuring the Effectiveness of Training and Development Programs.

ERIC Educational Resources Information Center

Helliwell, Tanis

1978-01-01

The article presents an outline of the methodology used in a study designed to evaluate the effectiveness of staff development courses for Ontario's Civil Service Commission. The procedure included a literature search, instructor interviews, and questionnaire development. (MF)

Co-ordination of the International Network of Nuclear Structure and Decay Data Evaluators; Summary Report of an IAEA Technical Meeting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abriola, D.; Tuli, J.

The IAEA Nuclear Data Section convened the 18th meeting of the International Network of Nuclear Structure and Decay Data Evaluators at the IAEA Headquarters, Vienna, 23 to 27 March 2009. This meeting was attended by 22 scientists from 14 Member States, plus IAEA staff, concerned with the compilation, evaluation and dissemination of nuclear structure and decay data. A summary of the meeting, recommendations/conclusions, data centre reports, and various proposals considered, modified and agreed by the participants are contained within this document. The International Network of Nuclear Structure and Decay Data (NSDD) Evaluators holds biennial meetings under the auspices of themore » IAEA, and consists of evaluation groups and data service centres in several countries. This network has the objective of providing up-to-date nuclear structure and decay data for all known nuclides by evaluating all existing experimental data. Data resulting from this international evaluation collaboration is included in the Evaluated Nuclear Structure Data File (ENSDF) and published in the journals Nuclear Physics A and Nuclear Data Sheets (NDS).« less

Meeting the challenges of global nuclear medicine technologist training in the 21st century: the IAEA Distance Assisted Training (DAT) program.

PubMed

Patterson, Heather E; Nunez, Margarita; Philotheou, Geraldine M; Hutton, Brian F

2013-05-01

Many countries have made significant investments in nuclear medicine (NM) technology with the acquisition of modern equipment and establishment of facilities, however, often appropriate training is not considered as part of these investments. Training for NM professionals is continually evolving, with a need to meet changing requirements in the workforce. Even places where established higher education courses are available, these do not necessarily cater to the practical component of training and the ever-changing technology that is central to medical imaging. The continuing advances in NM technology and growth of applications in quantitative clinical assessment place increases the pressure on technologists to learn and practice new techniques. Not only is training to understand new concepts limited but often there is inadequate training in the basics of NM and this can be a major constraint to the effective use of the evolving technology. Developing appropriate training programs for the broader international NM community is one of the goals of the International Atomic Energy Agency (IAEA). A particularly successful and relevant development has been the program on 'distance assisted training (DAT) for NM professionals'. The development of DAT was initiated in the 1990s through Australian Government funding, administered under auspices of the IAEA through its Regional Cooperative Agreement, involving most countries in Asia that are Member States of the IAEA. The project has resulted in the development of a set of training modules which are designed for use under direct supervision in the workplace, delivered through means of distance-learning. The program has undergone several revisions and peer reviews with the current version providing a comprehensive training package that is now available online. DAT has been utilized widely in Asia or the Pacific region, Latin America, and parts of Africa and Europe. Currently there are approximately 1000 registered participants

34 CFR 303.342 - Procedures for IFSP development, review, and evaluation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... development, review, and evaluation. (a) Meeting to develop initial IFSP—timelines. For a child who has been... 34 Education 2 2010-07-01 2010-07-01 false Procedures for IFSP development, review, and evaluation... PROGRAM FOR INFANTS AND TODDLERS WITH DISABILITIES Program and Service Components of a Statewide System of...

34 CFR 303.342 - Procedures for IFSP development, review, and evaluation.

Code of Federal Regulations, 2011 CFR

2011-07-01

... development, review, and evaluation. (a) Meeting to develop initial IFSP—timelines. For a child who has been... 34 Education 2 2011-07-01 2010-07-01 true Procedures for IFSP development, review, and evaluation... PROGRAM FOR INFANTS AND TODDLERS WITH DISABILITIES Program and Service Components of a Statewide System of...

The IAEA stopping power database, following the trends in stopping power of ions in matter

NASA Astrophysics Data System (ADS)

Montanari, C. C.; Dimitriou, P.

2017-10-01

The aim of this work is to present an overview of the state of art of the energy loss of ions in matter, based on the new developments in the stopping power database of the International Atomic Energy Agency (IAEA). This exhaustive collection of experimental data, graphs, programs and comparisons, is the legacy of Helmut Paul, who made it accessible to the global scientific community, and has been extensively employed in theoretical and experimental research during the last 25 years. The field of stopping power in matter is evolving, with new trends in materials of interest, including oxides, nitrides, polymers, and biological targets. Our goal is to identify areas of interest and emerging data needs to meet the requirements of a continuously developing user community.

Recent developments in the Dorfman-Berbaum-Metz procedure for multireader ROC study analysis.

PubMed

Hillis, Stephen L; Berbaum, Kevin S; Metz, Charles E

2008-05-01

The Dorfman-Berbaum-Metz (DBM) method has been one of the most popular methods for analyzing multireader receiver-operating characteristic (ROC) studies since it was proposed in 1992. Despite its popularity, the original procedure has several drawbacks: it is limited to jackknife accuracy estimates, it is substantially conservative, and it is not based on a satisfactory conceptual or theoretical model. Recently, solutions to these problems have been presented in three papers. Our purpose is to summarize and provide an overview of these recent developments. We present and discuss the recently proposed solutions for the various drawbacks of the original DBM method. We compare the solutions in a simulation study and find that they result in improved performance for the DBM procedure. We also compare the solutions using two real data studies and find that the modified DBM procedure that incorporates these solutions yields more significant results and clearer interpretations of the variance component parameters than the original DBM procedure. We recommend using the modified DBM procedure that incorporates the recent developments.

Value Engineering. Technical Manual. School Facilities Development Procedures Manual.

ERIC Educational Resources Information Center

Washington Office of the State Superintendent of Public Instruction, Olympia.

Value Engineering (VE) is a cost-optimizing technique used to analyze design quality and cost-effectiveness. The application of VE procedures to the design and construction of school facilities has been adopted by the state of Washington. This technical manual provides guidance in developing the scope and applicability of VE to school projects; in…

The development of a purification procedure for saxitoxin-induced protein.

PubMed

Smith, D S; Kitts, D D; Fenske, B; Owen, T G; Shyng, S

1995-02-01

A simple economical procedure for purifying saxitoxin-induced protein (SIP) from crude extracts of the small shore crab, Hemigrapsus oregenesis, was developed. (NH4)2SO4 precipitation, chymotrypsin digestion, heat treatment, gel filtration and ion-exchange-chromatography procedures were evaluated in purifying SIP. An enzyme immunoassay was used to determine the SIP yield and relative purity at each step of three procedures, thus permitting an assessment of the conditions required for maximum recovery. Response surface analysis was used in an attempt to determine the optimum temperature and exposure time for the heat treatment. A 20 min incubation at 65 degrees C was confirmed by electrophoretic analysis to be the best combination of time and temperature for achieving both an acceptable yield and purity of SIP. SIP in desalted concentrate was shown to be resistant to chymotrypsin proteolysis; however, this enzyme had deleterious effects on SIP purification at later stages of the procedure. The omission of the chymotrypsin digestion, and the inclusion of gel-filtration chromatography in the final clean-up step, resulted in the purification of SIP comparable with that achieved with affinity chromatography.

Development of Postoperative Diabetes Mellitus in Patients Undergoing Distal Pancreatectomy versus Whipple Procedure.

PubMed

Nguyen, Adrienne; Demirjian, Aram; Yamamoto, Maki; Hollenbach, Kathryn; Imagawa, David K

2017-10-01

Because the islets of Langerhans are more prevalent in the body and tail of the pancreas, distal pancreatectomy (DP) is believed to increase the likelihood of developing new onset diabetes mellitus (NODM). To determine whether the development of postoperative diabetes was more prevalent in patients undergoing DP or Whipple procedure, 472 patients undergoing either a DP (n = 122) or Whipple (n = 350), regardless of underlying pathology, were analyzed at one month postoperatively. Insulin or oral hypoglycemic requirements were assessed and patients were stratified into preoperative diabetic status: NODM or preexisting diabetes. A retrospective chart review of the 472 patients between 1996 and 2014 showed that the total rate of NODM after Whipple procedure was 43 per cent, which was not different from patients undergoing DP (45%). The incidence of preoperative diabetes was 12 per cent in patients undergoing the Whipple procedure and 17 per cent in the DP cohort. Thus, the overall incidence of diabetes after Whipple procedure was 54 and 49 per cent in the DP group. The development of diabetes was unrelated to the type of resection performed. Age more than 65 and Caucasian ethnicity were associated with postoperative diabetes regardless of the type of resection performed.

Development of a turbomachinery design optimization procedure using a multiple-parameter nonlinear perturbation method

NASA Technical Reports Server (NTRS)

Stahara, S. S.

1984-01-01

An investigation was carried out to complete the preliminary development of a combined perturbation/optimization procedure and associated computational code for designing optimized blade-to-blade profiles of turbomachinery blades. The overall purpose of the procedures developed is to provide demonstration of a rapid nonlinear perturbation method for minimizing the computational requirements associated with parametric design studies of turbomachinery flows. The method combines the multiple parameter nonlinear perturbation method, successfully developed in previous phases of this study, with the NASA TSONIC blade-to-blade turbomachinery flow solver, and the COPES-CONMIN optimization procedure into a user's code for designing optimized blade-to-blade surface profiles of turbomachinery blades. Results of several design applications and a documented version of the code together with a user's manual are provided.

Reference dosimeter system of the iaea

NASA Astrophysics Data System (ADS)

Mehta, Kishor; Girzikowsky, Reinhard

1995-09-01

Quality assurance programmes must be in operation at radiation processing facilities to satisfy national and international Standards. Since dosimetry has a vital function in these QA programmes, it is imperative that the dosimetry systems in use at these facilities are well calibrated with a traceability to a Primary Standard Dosimetry Laboratory. As a service to the Member States, the International Atomic Energy Agency operates the International Dose Assurance Service (IDAS) to assist in this process. The transfer standard dosimetry system that is used for this service is based on ESR spectrometry. The paper describes the activities undertaken at the IAEA Dosimetry Laboratory to establish the QA programme for its reference dosimetry system. There are four key elements of such a programme: quality assurance manual; calibration that is traceable to a Primary Standard Dosimetry Laboratory; a clear and detailed statement of uncertainty in the dose measurement; and, periodic quality audit.

DEVELOPMENT OF PROCEDURES FOR DERIVING TRAINING OBJECTIVES FOR JUNIOR OFFICER JOBS.

ERIC Educational Resources Information Center

AMMERMAN, HARRY L.

A SYSTEMATIC METHOD WAS DEVELOPED TO BE USED BY SERVICE SCHOOL PERSONNEL IN PREPARING JOB-ORIENTED TRAINING OBJECTIVES FOR JUNIOR OFFICERS, PRIMARILY IN THE FORM OF BEHAVIORAL STATEMENTS OF PERFORMANCE EXPECTED AFTER TRAINING. THE PROCEDURES DEVELOPED WERE (1) LISTING ALL TASKS FOR A JOB, (2) SELECTING TASKS FOR SOME FORMAL TRAINING, (3)…

Progress and status of the IAEA coordinated research project: production of Mo-99 using LEU fission or neutron activation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goldman, Ira N.; Adelfang, Pablo; Ramamoorthy, Natesan

2008-07-15

Since late 2004, the IAEA has developed and implemented a Coordinated Research Project (CRP) to assist countries interested in initiating indigenous, small-scale production of Mo-99 to meet local nuclear medicine requirements. The objective of the CRP is to provide interested countries with access to non-proprietary technologies and methods to produce Mo-99 using LEU foil or LEU mini-plate targets, or for the utilization of n,gamma neutron activation, e.g. through the use of gel generators. The project has made further progress since the RERTR 2006 meeting, with a Technical Workshop on Operational Aspects of Mo99 Production held 28-30 November 2006 in Viennamore » and the Second Research Coordination Meeting held in Bucharest, Romania 16-20 April 2007. The paper describes activities carried out as noted above, and as well as the provision of LEU foils to a number of participants, and the progress by a number of groups in preparing for LEU target assembly and disassembly, irradiation, chemical processing, and waste management. The participants' progress in particular on thermal hydraulics computations required for using LEU targets is notable, as also the progress in gel generator plant operations in India and Kazakhstan. Poland has joined as a new research agreement holder and an application by Egypt to be a contract holder is undergoing internal review in the IAEA and is expected to be approved. The IAEA has also participated in several open meetings of the U.S. National Academy of Sciences Study on Producing Medical Radioisotopes without HEU, which will also be discussed in the paper. (author)« less

Bilingualism and Procedural Learning in Typically Developing Children and Children with Language Impairment

ERIC Educational Resources Information Center

Park, Jisook; Miller, Carol A.; Rosenbaum, David A.; Sanjeevan, Teenu; van Hell, Janet G.; Weiss, Daniel J.; Mainela-Arnold, Elina

2018-01-01

Purpose: The aim of this study was to investigate whether dual language experience affects procedural learning ability in typically developing children and in children with specific language impairment (SLI). Method: We examined procedural learning in monolingual and bilingual school-aged children (ages 8-12 years) with and without SLI. The…

Secretary of Energy Steven Chu speaks to the 2009 IAEA General Conference delegation

ScienceCinema

Secretary Chu

2017-12-09

On Sept. 14, 2009, U.S. Secretary of Energy Steven Chu addressed the 2009 IAEA General Conference delegation. Chu is the first Cabinet official to discuss President Obama's nuclear security and nonproliferation agenda outside the United States since the President delivered his landmark speech in Prague in April 2009.

Development of RAD-Score: A Tool to Assess the Procedural Competence of Diagnostic Radiology Residents.

PubMed

Isupov, Inga; McInnes, Matthew D F; Hamstra, Stan J; Doherty, Geoffrey; Gupta, Ashish; Peddle, Susan; Jibri, Zaid; Rakhra, Kawan; Hibbert, Rebecca M

2017-04-01

The purpose of this study is to develop a tool to assess the procedural competence of radiology trainees, with sources of evidence gathered from five categories to support the construct validity of tool: content, response process, internal structure, relations to other variables, and consequences. A pilot form for assessing procedural competence among radiology residents, known as the RAD-Score tool, was developed by evaluating published literature and using a modified Delphi procedure involving a group of local content experts. The pilot version of the tool was tested by seven radiology department faculty members who evaluated procedures performed by 25 residents at one institution between October 2014 and June 2015. Residents were evaluated while performing multiple procedures in both clinical and simulation settings. The main outcome measure was the percentage of residents who were considered ready to perform procedures independently, with testing conducted to determine differences between levels of training. A total of 105 forms (for 52 procedures performed in a clinical setting and 53 procedures performed in a simulation setting) were collected for a variety of procedures (eight vascular or interventional, 42 body, 12 musculoskeletal, 23 chest, and 20 breast procedures). A statistically significant difference was noted in the percentage of trainees who were rated as being ready to perform a procedure independently (in postgraduate year [PGY] 2, 12% of residents; in PGY3, 61%; in PGY4, 85%; and in PGY5, 88%; p < 0.05); this difference persisted in the clinical and simulation settings. User feedback and psychometric analysis were used to create a final version of the form. This prospective study describes the successful development of a tool for assessing the procedural competence of radiology trainees with high levels of construct validity in multiple domains. Implementation of the tool in the radiology residency curriculum is planned and can play an

Development of Game-Like Simulations for Procedural Knowledge in Healthcare Education

ERIC Educational Resources Information Center

Torrente, Javier; Borro-Escribano, Blanca; Freire, Manuel; del Blanco, Ángel; Marchiori, Eugenio J.; Martinez-Ortiz, Iván; Moreno-Ger, Pablo; Fernández-Manjón, Baltasar

2014-01-01

We present EGDA, an educational game development approach focused on the teaching of procedural knowledge using a cost-effective approach. EGDA proposes four tasks: analysis, design, implementation, and quality assurance that are subdivided in a total of 12 subtasks. One of the benefits of EGDA is that anyone can apply it to develop a game since…

Databases and coordinated research projects at the IAEA on atomic processes in plasmas

NASA Astrophysics Data System (ADS)

Braams, Bastiaan J.; Chung, Hyun-Kyung

2012-05-01

The Atomic and Molecular Data Unit at the IAEA works with a network of national data centres to encourage and coordinate production and dissemination of fundamental data for atomic, molecular and plasma-material interaction (A+M/PMI) processes that are relevant to the realization of fusion energy. The Unit maintains numerical and bibliographical databases and has started a Wiki-style knowledge base. The Unit also contributes to A+M database interface standards and provides a search engine that offers a common interface to multiple numerical A+M/PMI databases. Coordinated Research Projects (CRPs) bring together fusion energy researchers and atomic, molecular and surface physicists for joint work towards the development of new data and new methods. The databases and current CRPs on A+M/PMI processes are briefly described here.

Databases and coordinated research projects at the IAEA on atomic processes in plasmas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Braams, Bastiaan J.; Chung, Hyun-Kyung

2012-05-25

The Atomic and Molecular Data Unit at the IAEA works with a network of national data centres to encourage and coordinate production and dissemination of fundamental data for atomic, molecular and plasma-material interaction (A+M/PMI) processes that are relevant to the realization of fusion energy. The Unit maintains numerical and bibliographical databases and has started a Wiki-style knowledge base. The Unit also contributes to A+M database interface standards and provides a search engine that offers a common interface to multiple numerical A+M/PMI databases. Coordinated Research Projects (CRPs) bring together fusion energy researchers and atomic, molecular and surface physicists for joint workmore » towards the development of new data and new methods. The databases and current CRPs on A+M/PMI processes are briefly described here.« less

Invasive Procedures in Preterm Children: Brain and Cognitive Development at School Age

PubMed Central

Vinall, Jillian; Miller, Steven P.; Bjornson, Bruce H.; Fitzpatrick, Kevin P.V.; Poskitt, Kenneth J.; Brant, Rollin; Synnes, Anne R.; Cepeda, Ivan L.

2014-01-01

BACKGROUND: Very preterm infants (born 24–32 weeks’ gestation) undergo numerous invasive procedures during neonatal care. Repeated skin-breaking procedures in rodents cause neuronal cell death, and in human preterm neonates higher numbers of invasive procedures from birth to term-equivalent age are associated with abnormal brain development, even after controlling for other clinical risk factors. It is unknown whether higher numbers of invasive procedures are associated with long-term alterations in brain microstructure and cognitive outcome at school age in children born very preterm. METHODS: Fifty children born very preterm underwent MRI and cognitive testing at median age 7.6 years (interquartile range, 7.5–7.7). T1- and T2-weighted images were assessed for the severity of brain injury. Magnetic resonance diffusion tensor sequences were used to measure fractional anisotropy (FA), an index of white matter (WM) maturation, from 7 anatomically defined WM regions. Child cognition was assessed using the Wechsler Intelligence Scale for Children–IV. Multivariate modeling was used to examine relationships between invasive procedures, brain microstructure, and cognition, adjusting for clinical confounders (eg, infection, ventilation, brain injury). RESULTS: Greater numbers of invasive procedures were associated with lower FA values of the WM at age 7 years (P = .01). The interaction between the number of procedures and FA was associated with IQ (P = .02), such that greater numbers of invasive procedures and lower FA of the superior WM were related to lower IQ. CONCLUSIONS: Invasive procedures during neonatal care contribute to long-term abnormalities in WM microstructure and lower IQ. PMID:24534406

Quality of radiotherapy services in post-Soviet countries: An IAEA survey.

PubMed

Rosenblatt, Eduardo; Fidarova, Elena; Ghosh, Sunita; Zubizarreta, Eduardo; Unterkirhere, Olga; Semikoz, Natalia; Sinaika, Valery; Kim, Viktor; Karamyan, Nerses; Isayev, Isa; Akbarov, Kamal; Lomidze, Darejan; Bondareva, Oksana; Tuzlucov, Piotr; Zardodkhonova, Manzura; Tkachev, Sergey; Kislyakova, Marina; Alimov, Jamshid; Pidlubna, Tetiana; Barton, Michael; Mackillop, William

2018-04-25

The quality of radiotherapy services in post-Soviet countries has not yet been studied following a formal methodology. The IAEA conducted a survey using two sets of validated radiation oncology quality indicators (ROIs). Eleven post-Soviet countries were assessed. A coordinator was designated for each country and acted as the liaison between the country and the IAEA. The methodology was a one-time cross-sectional survey using a 58-question tool in Russian. The questionnaire was based on two validated sets of ROIs: for radiotherapy centres, the indicators proposed by Cionini et al., and for data at the country level, the Australasian ROIs. The overall response ratio was 66.3%, but for the Russian Federation, it was 24%. Data were updated on radiotherapy infrastructure and equipment. 256 radiotherapy centres are operating 275 linear accelerators and 337 Cobalt-60 units. 61% of teletherapy machines are older than ten years. Analysis of ROIs revealed significant differences between these countries and radiotherapy practices in the West. Naming, task profile and education programmes of radiotherapy professionals are different than in the West. Most countries need modernization of their radiotherapy infrastructure coupled with adequate staffing numbers and updated education programmes focusing on evidence-based medicine, quality, and safety. Copyright © 2018 Elsevier B.V. All rights reserved.

Safe procedure development to manage hazardous drugs in the workplace.

PubMed

Gaspar Carreño, Marisa; Achau Muñoz, Rubén; Torrico Martín, Fátima; Agún Gonzalez, Juan José; Sanchez Santos, Jose Cristobal; Cercos Lletí, Ana Cristina; Ramos Orozco, Pedro

2017-03-01

To develop a safety working procedure for the employees in the Intermutual Hospital de Levante (HIL) in those areas of activity that deal with the handling of hazardous drugs (MP). The procedure was developed in six phases: 1) hazard definition; 2) definition and identification of processes and development of general correct work practices about hazardous drugs' selection and special handling; 3) detection, selection and set of specific recommendations to handle with hazardous drugs during the processes of preparation and administration included in the hospital GFT; 4) categorization of risk during the preparation/administration and development of an identification system; 5) information and training of professionals; 6) implementation of the identification measures and prevention guidelines. Six processes were detected handling HD. During those processes, thirty HD were identified included in the hospital GFT and a safer alternative was found for 6 of them. The HD were classified into 4 risk categories based on those measures to be taken during the preparation and administration of each of them. The development and implementation of specific safety-work processes dealing with medication handling, allows hospital managers to accomplish effectively with their legal obligations about the area of prevention and provides healthcare professional staff with the adequate techniques and safety equipment to avoid possible dangers and risks of some drugs. Copyright AULA MEDICA EDICIONES 2014. Published by AULA MEDICA. All rights reserved.

Issues and Procedures in the Development of Criterion Referenced Tests.

ERIC Educational Resources Information Center

Klein, Stephen P.; Kosecoff, Jacqueline

The basic steps and procedures in the development of criterion referenced tests (CRT), as well as the issues and problems associated with these activities are discussed. In the first section of the paper, the discussions focus upon the purpose and defining characteristics of CRTs, item construction and selection, improving item quality, content…

Guide for Developing and Evaluating an SFAR 36 Engineering Procedures Manual

DOT National Transportation Integrated Search

1997-05-22

This advisory circular (AC) sets forth an acceptable means, but not the only : means, for developing and evaluating a 14 Code of Federal Regulations (14CFR) : Special Federal Aviaton Regulation (SFAR)36 engineering procedures manual. As : such, the t...

Towards a tactical nuclear weapons treaty? Is There a Role of IAEA Tools of Safeguards?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saunders, Emily C.; Rowberry, Ariana N.; Fearey, Bryan L.

2012-07-12

In recent years, there is growing interest in formal negotiations on non-strategic or tactical nuclear weapons. With the negotiations of New START, there has been much speculation that a tactical nuclear weapons treaty should be included in the follow on to New START. This paper examines the current policy environment related to tactical weapons and some of the issues surrounding the definition of tactical nuclear weapons. We then map out the steps that would need to be taken in order to begin discussions on a tactical nuclear weapons treaty. These steps will review the potential role of the IAEA inmore » verification of a tactical nuclear weapons treaty. Specifically, does IAEA involvement in various arms control treaties serve as a useful roadmap on how to overcome some of the issues pertaining to a tactical nuclear weapons treaty?« less

A test of the IAEA code of practice for absorbed dose determination in photon and electron beams

NASA Astrophysics Data System (ADS)

Leitner, Arnold; Tiefenboeck, Wilhelm; Witzani, Josef; Strachotinsky, Christian

1990-12-01

The IAEA (International Atomic Energy Agency) code of practice TRS 277 gives recommendations for absorbed dose determination in high energy photon and electron beams based on the use of ionization chambers calibrated in terms of exposure of air kerma. The scope of the work was to test the code for cobalt 60 gamma radiation and for several radiation qualities at four different types of electron accelerators and to compare the ionization chamber dosimetry with ferrous sulphate dosimetry. The results show agreement between the two methods within about one per cent for all the investigated qualities. In addition the response of the TLD capsules of the IAEA/WHO TL dosimetry service was determined.

Image 100 procedures manual development: Applications system library definition and Image 100 software definition

NASA Technical Reports Server (NTRS)

Guseman, L. F., Jr.; Decell, H. P., Jr.

1975-01-01

An outline for an Image 100 procedures manual for Earth Resources Program image analysis was developed which sets forth guidelines that provide a basis for the preparation and updating of an Image 100 Procedures Manual. The scope of the outline was limited to definition of general features of a procedures manual together with special features of an interactive system. Computer programs were identified which should be implemented as part of an applications oriented library for the system.

Development of electrical test procedures for qualification of spacecraft against EID. Volume 2: Review and specification of test procedures

NASA Technical Reports Server (NTRS)

Wilkenfeld, J. M.; Harlacher, B. L.; Mathews, D.

1982-01-01

A combined experimental and analytical program to develop system electrical test procedures for the qualification of spacecraft against damage produced by space-electron-induced discharges (EID) occurring on spacecraft dielectric outer surfaces is described. A review and critical evaluation of possible approaches to qualify spacecraft against space electron-induced discharges (EID) is presented. A variety of possible schemes to simulate EID electromagnetic effects produced in spacecraft was studied. These techniques form the principal element of a provisional, recommended set of test procedures for the EID qualification spacecraft. Significant gaps in our knowledge about EID which impact the final specification of an electrical test to qualify spacecraft against EID are also identified.

[Nuclear energy and environment: review of the IAEA environmental projects].

PubMed

Fesenko, S; Fogt, G

2012-01-01

The review of the environmental projects of the International Atomic Energy Agency is presented. Basic IAEA documents intended to protect humans and the Environment are considered and their main features are discussed. Some challenging issues in the area of protection of the Environment and man, including the impact of nuclear facilities on the environment, radioactive waste management, and remediation of the areas affected by radiological accidents, nuclear testing and sites of nuclear facilities are also discussed. The need to maintain the existing knowledge in radioecology and protection of the environment is emphasised.

Development of QC Procedures for Ocean Data Obtained by National Research Projects of Korea

NASA Astrophysics Data System (ADS)

Kim, S. D.; Park, H. M.

2017-12-01

To establish data management system for ocean data obtained by national research projects of Ministry of Oceans and Fisheries of Korea, KIOST conducted standardization and development of QC procedures. After reviewing and analyzing the existing international and domestic ocean-data standards and QC procedures, the draft version of standards and QC procedures were prepared. The proposed standards and QC procedures were reviewed and revised by experts in the field of oceanography and academic societies several times. A technical report on the standards of 25 data items and 12 QC procedures for physical, chemical, biological and geological data items. The QC procedure for temperature and salinity data was set up by referring the manuals published by GTSPP, ARGO and IOOS QARTOD. It consists of 16 QC tests applicable for vertical profile data and time series data obtained in real-time mode and delay mode. Three regional range tests to inspect annual, seasonal and monthly variations were included in the procedure. Three programs were developed to calculate and provide upper limit and lower limit of temperature and salinity at depth from 0 to 1550m. TS data of World Ocean Database, ARGO, GTSPP and in-house data of KIOST were analysed statistically to calculate regional limit of Northwest Pacific area. Based on statistical analysis, the programs calculate regional ranges using mean and standard deviation at 3 kind of grid systems (3° grid, 1° grid and 0.5° grid) and provide recommendation. The QC procedures for 12 data items were set up during 1st phase of national program for data management (2012-2015) and are being applied to national research projects practically at 2nd phase (2016-2019). The QC procedures will be revised by reviewing the result of QC application when the 2nd phase of data management programs is completed.

Conditioning Procedure for Spent Cs-137 Sealed Sources in Egypt

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mohamed, Y.T.; Hasan, M.A.; Lasheen, Y.F.

2006-07-01

It is the duty of the Hot Laboratories and Waste Management Center, Egyptian Atomic Energy Authority to mange the radioactive waste generated from any user for radioactive materials in Egypt. The most hazardous or dangerous radioactive waste we collect is spent radioactive sealed sources that have to be managed safely to protect human, workers and environment from any undue burden for radiation. Through the Integrated Management Program Of Radioactive Sealed Sources In Egypt, IMPRSS all spent Cs-137 sources with low activity will be retrievable conditioned in 200 L drum with special lead shield to keep the surface dose rate lowermore » than 200 merm/h according to US regulations and IAEA guidelines. Using this procedure the EAEA will condition about 243 sources in 9 drums. (authors)« less

Developing an automated database for monitoring ultrasound- and computed tomography-guided procedure complications and diagnostic yield.

PubMed

Itri, Jason N; Jones, Lisa P; Kim, Woojin; Boonn, William W; Kolansky, Ana S; Hilton, Susan; Zafar, Hanna M

2014-04-01

Monitoring complications and diagnostic yield for image-guided procedures is an important component of maintaining high quality patient care promoted by professional societies in radiology and accreditation organizations such as the American College of Radiology (ACR) and Joint Commission. These outcome metrics can be used as part of a comprehensive quality assurance/quality improvement program to reduce variation in clinical practice, provide opportunities to engage in practice quality improvement, and contribute to developing national benchmarks and standards. The purpose of this article is to describe the development and successful implementation of an automated web-based software application to monitor procedural outcomes for US- and CT-guided procedures in an academic radiology department. The open source tools PHP: Hypertext Preprocessor (PHP) and MySQL were used to extract relevant procedural information from the Radiology Information System (RIS), auto-populate the procedure log database, and develop a user interface that generates real-time reports of complication rates and diagnostic yield by site and by operator. Utilizing structured radiology report templates resulted in significantly improved accuracy of information auto-populated from radiology reports, as well as greater compliance with manual data entry. An automated web-based procedure log database is an effective tool to reliably track complication rates and diagnostic yield for US- and CT-guided procedures performed in a radiology department.

Development of an efficient procedure for calculating the aerodynamic effects of planform variation

NASA Technical Reports Server (NTRS)

Mercer, J. E.; Geller, E. W.

1981-01-01

Numerical procedures to compute gradients in aerodynamic loading due to planform shape changes using panel method codes were studied. Two procedures were investigated: one computed the aerodynamic perturbation directly; the other computed the aerodynamic loading on the perturbed planform and on the base planform and then differenced these values to obtain the perturbation in loading. It is indicated that computing the perturbed values directly can not be done satisfactorily without proper aerodynamic representation of the pressure singularity at the leading edge of a thin wing. For the alternative procedure, a technique was developed which saves most of the time-consuming computations from a panel method calculation for the base planform. Using this procedure the perturbed loading can be calculated in about one-tenth the time of that for the base solution.

Measurement of ²²⁶Ra in soil from oil field: advantages of γ-ray spectrometry and application to the IAEA-448 CRM.

PubMed

Ceccatelli, A; Katona, R; Kis-Benedek, G; Pitois, A

2014-05-01

The analytical performance of gamma-ray spectrometry for the measurement of (226)Ra in TENORM (Technically Enhanced Naturally Occurring Radioactive Material) soil was investigated by the IAEA. Fast results were obtained for characterization and certification of a new TENORM Certified Reference Material (CRM), identified as IAEA-448 (soil from oil field). The combined standard uncertainty of the gamma-ray spectrometry results is of the order of 2-3% for massic activity measurement values ranging from 16500 Bq kg(-1) to 21500 Bq kg(-1). Methodologies used for the production and certification of the IAEA-448 CRM are presented. Analytical results were confirmed by alpha spectrometry. The "t" test showed agreement between alpha and gamma results at 95% confidence level. © 2013 Published by Elsevier Ltd.

Lessons from UNSCOM and IAEA regarding remote monitoring and air sampling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dupree, S.A.

1996-01-01

In 1991, at the direction of the United Nations Security Council, UNSCOM and IAEA developed plans for On-going Monitoring and Verification (OMV) in Iraq. The plans were accepted by the Security Council and remote monitoring and atmospheric sampling equipment has been installed at selected sites in Iraq. The remote monitoring equipment consists of video cameras and sensors positioned to observe equipment or activities at sites that could be used to support the development or manufacture of weapons of mass destruction, or long-range missiles. The atmospheric sampling equipment provides unattended collection of chemical samples from sites that could be used tomore » support the development or manufacture of chemical weapon agents. To support OMV in Iraq, UNSCOM has established the Baghdad Monitoring and Verification Centre. Imagery from the remote monitoring cameras can be accessed in near-real time from the Centre through RIF communication links with the monitored sites. The OMV program in Iraq has implications for international cooperative monitoring in both global and regional contexts. However, monitoring systems such as those used in Iraq are not sufficient, in and of themselves, to guarantee the absence of prohibited activities. Such systems cannot replace on-site inspections by competent, trained inspectors. However, monitoring similar to that used in Iraq can contribute to openness and confidence building, to the development of mutual trust, and to the improvement of regional stability.« less

Lessons Learned from the Development of an Example Precision Information Environment for International Safeguards

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gastelum, Zoe N.; Henry, Michael J.; Burtner, IV, E. R.

The International Atomic Energy Agency (IAEA) is interested in increasing capabilities of IAEA safeguards inspectors to access information that would improve their situational awareness on the job. A mobile information platform could potentially provide access to information, analytics, and technical and logistical support to inspectors in the field, as well as providing regular updates to analysts at IAEA Headquarters in Vienna or at satellite offices. To demonstrate the potential capability of such a system, Pacific Northwest National Laboratory (PNNL) implemented a number of example capabilities within a PNNL-developed precision information environment (PIE), and using a tablet as a mobile informationmore » platform. PNNL’s safeguards proof-of-concept PIE intends to; demonstrate novel applications of mobile information platforms to international safeguards use cases; demonstrate proof-of-principle capability implementation; and provide “vision” for capabilities that could be implemented. This report documents the lessons learned from this two-year development activity for the Precision Information Environment for International Safeguards (PIE-IS), describing the developed capabilities, technical challenges, and considerations for future development, so that developers working to develop a similar system for the IAEA or other safeguards agencies might benefit from our work.« less

Fairness as partiality aversion: the development of procedural justice.

PubMed

Shaw, Alex; Olson, Kristina

2014-03-01

Adults and children dislike inequity-people being paid unequally for equal work. However, adults will allow inequity if the inequity is determined using an impartial procedure, indicating that they value procedural justice. It is unknown whether children value procedural justice when distributing resources. We investigated whether 5- to 8-year-old children would willingly create inequity between two recipients if they could do so using an impartial procedure. In Experiment 1, children preferred to use an impartial procedure (spinning a wheel that gave both recipients an equal chance to get a resource) over a partial procedure (spinning a wheel that gave one recipient a much better chance to get the resource). In Experiments 2 and 3, children preferred to use the same impartial procedure to assign a resource to one of two recipients, even over an option of keeping things equal by throwing the resource in the trash. Importantly, children preferred to throw the resource in the trash to uphold equality when the only other option was a partial procedure. Older children showed a stronger aversion to using partial procedures than younger children. These results suggest that children value procedural justice increasingly during middle childhood and that their fairness concerns may be more about avoiding partiality than inequity per se. Copyright © 2013 Elsevier Inc. All rights reserved.

The Development of a Procedure to Encourage Certain Facilitative Behaviors of Classroom Teachers.

ERIC Educational Resources Information Center

Eggert, Wallace V.; Moore, John N.

The main purpose of this study was to develop a procedure whereby teachers might improve their interpersonal transactions with students. Concomitant purposes were to develop a limited category coding system for easy use by classroom teachers and to develop a classroom observation system for research purposes. Sixteen teachers (three primary, nine…

Development of coring procedures applied to Si, CdTe, and CIGS solar panels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moutinho, H. R.; Johnston, S.; To, B.

Most of the research on the performance and degradation of photovoltaic modules is based on macroscale measurements of device parameters such as efficiency, fill factor, open-circuit voltage, and short-circuit current. Our goal is to develop the capabilities to allow us to study the degradation of these parameters in the micro- and nanometer scale and to relate our results to performance parameters. To achieve this objective, the first step is to be able to access small samples from specific areas of the solar panels without changing the properties of the material. In this paper, we describe two coring procedures that wemore » developed and applied to Si, CIGS, and CdTe solar panels. In the first procedure, we cored full samples, whereas in the second we performed a partial coring that keeps the tempered glass intact. The cored samples were analyzed by different analytical techniques before and after coring, at the same locations, and no damage during the coring procedure was observed.« less

Development of coring procedures applied to Si, CdTe, and CIGS solar panels

DOE PAGES

Moutinho, H. R.; Johnston, S.; To, B.; ...

2018-01-04

Most of the research on the performance and degradation of photovoltaic modules is based on macroscale measurements of device parameters such as efficiency, fill factor, open-circuit voltage, and short-circuit current. Our goal is to develop the capabilities to allow us to study the degradation of these parameters in the micro- and nanometer scale and to relate our results to performance parameters. To achieve this objective, the first step is to be able to access small samples from specific areas of the solar panels without changing the properties of the material. In this paper, we describe two coring procedures that wemore » developed and applied to Si, CIGS, and CdTe solar panels. In the first procedure, we cored full samples, whereas in the second we performed a partial coring that keeps the tempered glass intact. The cored samples were analyzed by different analytical techniques before and after coring, at the same locations, and no damage during the coring procedure was observed.« less

Syracuse University's Center for Instructional Development; Its Role, Organization, and Procedures.

ERIC Educational Resources Information Center

Diamond, Robert M.

A brief report on the Syracuse University Center for Instructional Development is presented which describes the Center's organizational structure and operational procedures. The center combines support services for video, audio, graphics and photographic preparation of materials for instructional use; a research and evaluation unit to assess…

Developing a preservation policy and procedure statement for a health sciences library.

PubMed Central

Paulson, B A

1989-01-01

The preconditions for creating a preservation policy document in a health sciences library are an existing preservation policy for the institution of which it is a part and administrative support for preservation. The assumption underlying preservation activity, from the formulation of general guidelines to the detail of operating procedure, is that collection development and preservation are complementary functions. Documentation of operational procedures in some detail should be a part of the statement. Since preservation activity cuts across functional library structures, all management staff should be involved in the planning process and be made aware of their responsibilities. The creation of a preservation policy statement will highlight unaddressed issues, procedural inadequacies, and differences in staff perceptions of priorities, but a written statement provides a framework for setting priorities and making decisions. PMID:2758183

Documentation for a Structural Optimization Procedure Developed Using the Engineering Analysis Language (EAL)

NASA Technical Reports Server (NTRS)

Martin, Carl J., Jr.

1996-01-01

This report describes a structural optimization procedure developed for use with the Engineering Analysis Language (EAL) finite element analysis system. The procedure is written primarily in the EAL command language. Three external processors which are written in FORTRAN generate equivalent stiffnesses and evaluate stress and local buckling constraints for the sections. Several built-up structural sections were coded into the design procedures. These structural sections were selected for use in aircraft design, but are suitable for other applications. Sensitivity calculations use the semi-analytic method, and an extensive effort has been made to increase the execution speed and reduce the storage requirements. There is also an approximate sensitivity update method included which can significantly reduce computational time. The optimization is performed by an implementation of the MINOS V5.4 linear programming routine in a sequential liner programming procedure.

Development of Facial Rejuvenation Procedures: Thirty Years of Clinical Experience with Face Lifts

PubMed Central

Kim, Byung Jun; Choi, Jun Ho

2015-01-01

Facial rejuvenation procedures can be roughly divided into face lift surgery and nonoperative, less invasive procedures, such as fat grafts, fillers, botulinum toxin injections, thread lifts, or laserbrasion. Face lift surgery or rhytidectomy is the procedure most directly associated with rejuvenation, due to its fundamental ability to restore the anatomical changes caused by aging. Various methods of face lift surgery have been developed over the last hundred years, thanks to advances in the understanding of facial anatomy and the mechanisms of aging, as well as the dedication of innovative surgeons. However, no generally applicable standard method exists, because the condition of each patient is different, and each operative method has advantages and disadvantages. Specific characteristics of the skin of Asians and their skeletal anatomy should be considered when determining the operative method to be used on Asian patients. Plastic surgeons should improve their ability to analyze the original aesthetic properties and problem areas of each patient, drawing on scientific knowledge about the aging process, and they should develop the skills necessary to perform various rejuvenative techniques. In the present article, we reviewed various face lift procedures and the current methods of modified double plane face lift, based on our clinical experience of over 30 years. PMID:26430622

Development of an Observational Procedure for Assessment of Parent-Child Interaction.

ERIC Educational Resources Information Center

Cunningham, Jo Lynn; Boger, Robert P.

The feasibility of using an observational rating schedule to elicit information about parent-child interaction was studied. The Parent-Child Interaction Rating Procedure (P-CIRP), focusing specifically on parent-child interaction with a structured teaching task, was developed for this purpose. The interaction setting is teaching the child simple…

On the status of IAEA delta-13C stable isotope reference materials.

NASA Astrophysics Data System (ADS)

Assonov, Sergey; Groening, Manfred; Fajgelj, Ales

2016-04-01

For practical reasons all isotope measurements are performed on relative scales realized through the use of international, scale-defining primary standards. In fact these standards were materials (artefacts, similar to prototypes of meter and kg) selected based on their properties. The VPDB delta-13C scale is realised via two highest-level reference materials NBS19 and LSVEC, the first defining the scale and the second aimed to normalise lab-to-lab calibrations. These two reference materials (RMs) have been maintained and distributed by IAEA and NIST. The priority task is to maintain these primary RMs at the required uncertainty level, thus ensuring the long-term scale consistency. The second task is to introduce replacements when needed (currently for exhausted NBS19, work in progress). The next is to produce a family of lower level RMs (secondary, tertiary) addressing needs of various applications (with different delta values, in different physical-chemical forms) and their needs for the uncertainty; these RMs should be traceable to the highest level RMs. Presently three is a need for a range of RMs addressing existing and newly emerging analytical techniques (e.g. optical isotopic analysers) in form of calibrated CO2 gases with different delta-13C values. All that implies creating a family of delta-13C stable isotope reference materials. Presently IAEA works on replacement for NBS19 and planning new RMs. Besides, we found that LSVEC (introduced as second anchor for the VPDB scale in 2006) demonstrate a considerable scatter of its delta-13C value which implies a potential bias of the property value and increased value uncertainty which may conflict with uncertainty requirements for atmospheric monitoring. That is not compatible with the status of LSVEC, and therefore it should be replaced as soon as possible. The presentation will give an overview of the current status, the strategic plan of developments and the near future steps.

The role of human drug self-administration procedures in the development of medications

PubMed Central

Comer, SD; Ashworth, JB; Foltin, RW; Johanson, CE; Zacny, JP; Walsh, SL

2008-01-01

The purpose of this review is to illustrate the utility and value of employing human self-administration procedures in medication development, including abuse liability assessments of novel medications and evaluation of potential pharmacotherapies for substance use disorders. Traditionally, human abuse liability testing has relied primarily on subjective reports describing drug action by use of questionnaires; similarly, drug interactions between putative treatment agents and the drugs of abuse have relied on these measures. Subjective reports are highly valued because they provide qualitative and quantitative information about the characteristics of central and peripheral pharmacodynamic effects as well as safety and tolerability. However, self-administration procedures directly examine the behavior of interest – that is, drug taking. The present paper 1) reviews the most commonly used human self-administration procedures, 2) discusses the concordance of subjective reports and self-administration within the context of medications development for substance use disorders, focusing primarily on illustrative examples from development efforts with opioid and cocaine dependence, and 3) explores the utility of applying self-administration procedures to assess the abuse liability of novel compounds, including “abuse deterrent” formulations (ADFs). The review will focus on opioid and cocaine dependence because a rich database from both clinical laboratory and clinical trial research exists for these two drug classes. The data reviewed suggest that drug-induced changes in self-administration and subjective effects are not always concordant. Therefore, assessment of self-administration in combination with subjective effects provides a more comprehensive picture that may have improved predictive validity for translating to the clinical setting. PMID:18436394

Development of a Composite Tailoring Procedure for Airplane Wings

NASA Technical Reports Server (NTRS)

Chattopadhyay, Aditi

2000-01-01

The quest for finding optimum solutions to engineering problems has existed for a long time. In modern times, the development of optimization as a branch of applied mathematics is regarded to have originated in the works of Newton, Bernoulli and Euler. Venkayya has presented a historical perspective on optimization in [1]. The term 'optimization' is defined by Ashley [2] as a procedure "...which attempts to choose the variables in a design process so as formally to achieve the best value of some performance index while not violating any of the associated conditions or constraints". Ashley presented an extensive review of practical applications of optimization in the aeronautical field till about 1980 [2]. It was noted that there existed an enormous amount of published literature in the field of optimization, but its practical applications in industry were very limited. Over the past 15 years, though, optimization has been widely applied to address practical problems in aerospace design [3-5]. The design of high performance aerospace systems is a complex task. It involves the integration of several disciplines such as aerodynamics, structural analysis, dynamics, and aeroelasticity. The problem involves multiple objectives and constraints pertaining to the design criteria associated with each of these disciplines. Many important trade-offs exist between the parameters involved which are used to define the different disciplines. Therefore, the development of multidisciplinary design optimization (MDO) techniques, in which different disciplines and design parameters are coupled into a closed loop numerical procedure, seems appropriate to address such a complex problem. The importance of MDO in successful design of aerospace systems has been long recognized. Recent developments in this field have been surveyed by Sobieszczanski-Sobieski and Haftka [6].

Development of an Expert System for Representing Procedural Knowledge

NASA Technical Reports Server (NTRS)

Georgeff, Michael P.; Lansky, Amy L.

1985-01-01

A high level of automation is of paramount importance in most space operations. It is critical for unmanned missions and greatly increases the effectiveness of manned missions. However, although many functions can be automated by using advanced engineering techniques, others require complex reasoning, sensing, and manipulatory capabilities that go beyond this technology. Automation of fault diagnosis and malfunction handling is a case in point. The military have long been interested in this problem, and have developed automatic test equipment to aid in the maintenance of complex military hardware. These systems are all based on conventional software and engineering techniques. However, the effectiveness of such test equipment is severely limited. The equipment is inflexible and unresponsive to the skill level of the technicians using it. The diagnostic procedures cannot be matched to the exigencies of the current situation nor can they cope with reconfiguration or modification of the items under test. The diagnosis cannot be guided by useful advice from technicians and, when a fault cannot be isolated, no explanation is given as to the cause of failure. Because these systems perform a prescribed sequence of tests, they cannot utilize knowledge of a particular situation to focus attention on more likely trouble spots. Consequently, real-time performance is highly unsatisfactory. Furthermore, the cost of developing test software is substantial and time to maturation is excessive. Significant advances in artificial intelligence (AI) have recently led to the development of powerful and flexible reasoning systems, known as expert or knowledge-based systems. We have devised a powerful and theoretically sound scheme for representing and reasoning about procedural knowledge.

Development of Criteria and Procedures for Management of Classified Document Collections.

ERIC Educational Resources Information Center

Rea, Jack C.

The report describes work done in development of criteria and procedures for management of collections of classified documents. Material is presented on philosophy of operation, concept of user service, accession and retention. Much of the discussion is based upon the concept of conversion to a microfiche-oriented library; however, hard copy…

Reference Dosimetry according to the New German Protocol DIN 6800-2 and Comparison with IAEA TRS 398 and AAPM TG 51*

PubMed Central

Zakaria, A; Schuette, W; Younan, C

2011-01-01

The preceding DIN 6800-2 (1997) protocol has been revised by a German task group and its latest version was published in March 2008 as the national standard dosimetry protocol DIN 6800-2 (2008 March). Since then, in Germany the determination of absorbed dose to water for high-energy photon and electron beams has to be performed according to this new German dosimetry protocol. The IAEA Code of Practice TRS 398 (2000) and the AAPM TG-51 are the two main protocols applied internationally. The new German version has widely adapted the methodology and dosimetric data of TRS-398. This paper investigates systematically the DIN 6800-2 protocol and compares it with the procedures and results obtained by using the international protocols. The investigation was performed with 6 MV and 18 MV photon beams as well as with electron beams from 5 MeV to 21 MeV. While only cylindrical chambers were used for photon beams, the measurements of electron beams were performed by using cylindrical and plane-parallel chambers. It was found that the discrepancies in the determination of absorbed dose to water among the three protocols were 0.23% for photon beams and 1.2% for electron beams. The determination of water absorbed dose was also checked by a national audit procedure using TLDs. The comparison between the measurements following the DIN 6800-2 protocol and the TLD audit-procedure confirmed a difference of less than 2%. The advantage of the new German protocol DIN 6800-2 lies in the renouncement on the cross calibration procedure as well as its clear presentation of formulas and parameters. In the past, the different protocols evoluted differently from time to time. Fortunately today, a good convergence has been obtained in concepts and methods. PMID:22287987

Reference Dosimetry according to the New German Protocol DIN 6800-2 and Comparison with IAEA TRS 398 and AAPM TG 51.

PubMed

Zakaria, A; Schuette, W; Younan, C

2011-04-01

The preceding DIN 6800-2 (1997) protocol has been revised by a German task group and its latest version was published in March 2008 as the national standard dosimetry protocol DIN 6800-2 (2008 March). Since then, in Germany the determination of absorbed dose to water for high-energy photon and electron beams has to be performed according to this new German dosimetry protocol. The IAEA Code of Practice TRS 398 (2000) and the AAPM TG-51 are the two main protocols applied internationally. The new German version has widely adapted the methodology and dosimetric data of TRS-398. This paper investigates systematically the DIN 6800-2 protocol and compares it with the procedures and results obtained by using the international protocols. The investigation was performed with 6 MV and 18 MV photon beams as well as with electron beams from 5 MeV to 21 MeV. While only cylindrical chambers were used for photon beams, the measurements of electron beams were performed by using cylindrical and plane-parallel chambers. It was found that the discrepancies in the determination of absorbed dose to water among the three protocols were 0.23% for photon beams and 1.2% for electron beams. The determination of water absorbed dose was also checked by a national audit procedure using TLDs. The comparison between the measurements following the DIN 6800-2 protocol and the TLD audit-procedure confirmed a difference of less than 2%. The advantage of the new German protocol DIN 6800-2 lies in the renouncement on the cross calibration procedure as well as its clear presentation of formulas and parameters. In the past, the different protocols evoluted differently from time to time. Fortunately today, a good convergence has been obtained in concepts and methods.

Development of a tool to support holistic generic assessment of clinical procedure skills.

PubMed

McKinley, Robert K; Strand, Janice; Gray, Tracey; Schuwirth, Lambert; Alun-Jones, Tom; Miller, Helen

2008-06-01

The challenges of maintaining comprehensive banks of valid checklists make context-specific checklists for assessment of clinical procedural skills problematic. This paper reports the development of a tool which supports generic holistic assessment of clinical procedural skills. We carried out a literature review, focus groups and non-participant observation of assessments with interview of participants, participant evaluation of a pilot objective structured clinical examination (OSCE), a national modified Delphi study with prior definitions of consensus and an OSCE. Participants were volunteers from a large acute teaching trust, a teaching primary care trust and a national sample of National Health Service staff. Results In total, 86 students, trainees and staff took part in the focus groups, observation of assessments and pilot OSCE, 252 in the Delphi study and 46 candidates and 50 assessors in the final OSCE. We developed a prototype tool with 5 broad categories amongst which were distributed 38 component competencies. There was > 70% agreement (our prior definition of consensus) at the first round of the Delphi study for inclusion of all categories and themes and no consensus for inclusion of additional categories or themes. Generalisability was 0.76. An OSCE based on the instrument has a predicted reliability of 0.79 with 12 stations and 1 assessor per station or 10 stations and 2 assessors per station. This clinical procedural skills assessment tool enables reliable assessment and has content and face validity for the assessment of clinical procedural skills. We have designated it the Leicester Clinical Procedure Assessment Tool (LCAT).

Development of AM 1.5 global measurement procedures and international cell measurement round robin

NASA Technical Reports Server (NTRS)

Mueller, R.

1985-01-01

The development of the capability for measurement under global irradiance spectral distribution is reported. The airmass 1.5 global measurement procedure is given. Also given is the procedure and justification for using the large area pulsed solar simulator (LAPSS). The status of the international round robin of reference cell measurements managed by the Commission of European Communities (CEC) is described.

12th IAEA Technical Meeting on Energetic Particles in Magnetic Confinement Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berk, Herbert L.; Breizman, Boris N.

2014-02-21

The 12th IAEA Technical Meeting on Energetic Particles in Magnetic Confinement Systems took place in Austin, Texas (7–11 September 2011). This meeting was organized jointly with the 5th IAEA Technical Meeting on Theory of Plasma Instabilities (5–7 September 2011). The two meetings shared one day (7 September 2011) with presentations relevant to both groups. Some of the work reported at these meetings was then published in a special issue of Nuclear Fusion [Nucl. Fusion 52 (2012)]. Summaries of the Energetic Particle Conference presentations were given by Kazuo Toi and Boris Breizman. They respectively discussed the experimental and theoretical progress presentedmore » at the meeting. Highlights of this meeting include the tremendous progress that has been achieved in the development of diagnostics that enables the ‘viewing’ of internal fluctuations and allows comparison with theoretical predictions, as demonstrated, for example, in the talks of P. Lauber and M. Osakabe. The need and development of hardened diagnostics in the severe radiation environment, such as those that will exist in ITER, was discussed in the talks of V. Kiptily and V.A. Kazakhov. In theoretical studies, much of the effort is focused on nonlinear phenomena. For example, detailed comparison of theory and experiment on D-III-D on the n = 0 geodesic mode was reported in separate papers by R. Nazikian and G. Fu. A large number of theoretical papers were presented on wave chirping including a paper by B.N. Breizman, which notes that wave chirping from a single frequency may emanate continuously once marginal stability conditions have been established. Another area of wide interest was the detailed study of alpha orbits in a burning plasma, where losses can come from symmetry breaking due to finite coil number or magnetic field imperfections introduced by diagnostic or test modules. An important area of development, covered by M.A. Hole and D.A. Spong, is concerned with the self

The Development of a Contextual Information Framework Model as a Potential IAEA Strategy to Maintain Radioactive Waste Knowledge

DOE Office of Scientific and Technical Information (OSTI.GOV)

Upshall, I.R.; McCarthy, G.J.

impossibly complex socio-technical environments into information architectures or networks with remarkable and useful properties. The International Atomic Energy Agency, in its ongoing work to encourage the application of systems to manage radioactive waste information over the long term, has embraced the contextual information framework as a potentially viable approach to this particular challenge. To this end, it invited Member States to contribute to the production of a Safety Report that used the contextual information framework model, building on the wealth of existing IAEA guidance. The report focuses, not on the important area of records management, but on the benefits that can arise from the development of an information management approach that increases the likelihood that future generations will recognise the significance and value of the information contained in these records. Our understanding of 'inter-generational transfer' should extend beyond the simple physical transfer of records into an archival repository towards the establishment of a working culture that places sufficient contemporary information into a form that ensures it remains accessible, and ultimately enhances, the knowledge of future generations. Making information accessible is therefore the key and whilst the use of stable records media, storage environments and quality assurance are important elements, they cannot be considered solutions in themselves. This paper articulates some of the lessons that have been learned about using the contextual information framework model when applied to the long term management of radioactive waste. The draft IAEA Safety Report entitled 'Preservation and Transfer to Future Generations of Information Important to the Safety of Waste Disposal Facilities', on which this paper is based, is expected to be published in 2007. (authors)« less

A new marine sediment certified reference material (CRM) for the determination of persistent organic contaminants: IAEA-459.

PubMed

Tolosa, Imma; Cassi, Roberto; Huertas, David

2018-04-11

A new marine sediment certified reference material (IAEA 459) with very low concentrations (μg kg -1 ) for a variety of persistent organic contaminants (POPs) listed by the Stockholm Convention, as well as other POPs and priority substances (PSs) listed in many environmental monitoring programs was developed by the IAEA. The sediment material was collected from the Ham River estuary in South Korea, and the assigned final values were derived from robust statistics on the results provided by selected laboratories which demonstrated technical and quality competence, following the guidance given in ISO Guide 35. The robust mean of the laboratory means was assigned as certified values, for those compounds where the assigned value was derived from at least five datasets and its relative expanded uncertainty was less than 40% of the assigned value (most of the values ranging from 8 to 20%). All the datasets were derived from at least two different analytical techniques which have allowed the assignment of certified concentrations for 22 polychlorinated biphenyl (PCB) congeners, 6 organochlorinated (OC) pesticides, 5 polybrominated diphenyl ethers (PBDEs), and 18 polycyclic aromatic hydrocarbon (PAHs). Mass fractions of compounds that did not fulfill the criteria of certification are considered information values, which include 29 PAHs, 11 PCBs, 16 OC pesticides, and 5 PBDEs. The extensive characterization and associated uncertainties at concentration levels close to the marine sediment quality guidelines will make CRM 459 a valuable matrix reference material for use in marine environmental monitoring programs.

Developing policies and procedures for a picture archiving and communication system.

PubMed

Gaytos, B

2001-06-01

Policies and procedures (P&P) constitute the mechanism for planning, standardizing, and documenting the provision of clinical services. Upon approval by hospital management, the P&P is an official statement of hospital rules and regulations. Each P&P establishes organizational responsibility for providing services. P&P are a mechanism for communicating standard operating procedures to hospital and medical staff. P&P serve as a reference document for unusual events, as well as routine procedures. P&P are often reviewed by inspection teams from the Joint Commission on Accreditation of Hospital Organizations (JCAHO) to determine whether the hospital has documented systematic practices. A picture archival and communications system (PACS) provides a new vehicle for providing radiology services. P&P that were designed for conventional film-based imaging are often not appropriate for electronic imaging. Because PACS is new and not yet widespread, good examples of PACS P&P are not yet available. JCAHO has no official requirements for PACS: PACS is viewed only as a means for the hospital to accomplish its work. Successful P&P development is a team effort, drafted by personnel responsible for executing the procedure, assisted by staff proficient in PACS technology, and tested in the field. The P&P should be reviewed and approved by management personnel knowledgeable about hospital and imaging operations. P&P should be written in clear and concise language. Successful P&P development is an ongoing effort. P&P must be periodically reviewed and updated to reflect changes in PACS technology and changes in clinical operations. New P&P must be developed when a deficit is noted. PACS security is a good example of a topic worthy of P&P development, especially in the face of the Health Insurance Portability and Accountability Act (HIPAA) legislation of 1996. What are the provisions for access control? Does the system include a feature for automatic shut-off of the software? Are there

DEVELOPMENT OF AGENTS AND PROCEDURES FOR DECONTAMINATION OF THE YANKEE REACTOR PRIMARY COOLANT SYSTEM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Watkins, R.M.

1959-03-01

Developments relative to decontamination achieved under the Yankee Reasearch and Development program are reported. The decontamination of a large test loop which had been used to conduct corrosion rate studies for the Yankee reactor program is described. The basic permanganate-citrate decontamination procedure suggested for application in Yankee reactor primary system cleanup was used. A study of the chemistry of this decontamination operation is presented, together with conclusions pertaining to the effectiveness of the solutions under the conditions studied. In an attempt to further improve the efficiency of the procedure, an additional series of static and dynamic tests was performcd usingmore » contaminated sections of stainless steel tubing from the original SlW steam generator. Survival variables in the process (reagent composition, contact time, temperature, and flow velocity) were studied. The changes in decontamination efficiency produced by these variations are discussed and compared with results obtained throughthe use of similar procedures. Based on the observations made, conclusions are drawn concerning the optimum conditions for this cleanup process, a new set of suggested basic permanganate-citrate decontamination instructions is presented, and recommendations are made concerning future studies involving this procedure. (auth)« less

Development of a composite tailoring procedure for airplane wing

NASA Technical Reports Server (NTRS)

Chattopadhyay, Aditi; Zhang, Sen

1995-01-01

The development of a composite wing box section using a higher order-theory is proposed for accurate and efficient estimation of both static and dynamic responses. The theory includes the effect of through-the-thickness transverse shear deformations which is important in laminated composites and is ignored in the classical approach. The box beam analysis is integrated with an aeroelastic analysis to investigate the effect of composite tailoring using a formal design optimization technique. A hybrid optimization procedure is proposed for addressing both continuous and discrete design variables.

Advancing Continence in Typically Developing Children: Adapting the Procedures of Foxx and Azrin for Primary Care.

PubMed

Warzak, William J; Forcino, Stacy S; Sanberg, Sela Ann; Gross, Amy C

2016-01-01

To (1) identify and summarize procedures of Foxx and Azrin's classic toilet training protocol that continue to be used in training typically developing children and (2) adapt recent findings with the original Foxx and Azrin procedures to inform practical suggestions for the rapid toilet training of typically developing children in the primary care setting. Literature searches of PsychINFO and MEDLINE databases used the search terms "(toilet* OR potty* AND train*)." Selection criteria were only peer-reviewed experimental articles that evaluated intensive toilet training with typically developing children. Exclusion criteria were (1) nonpeer reviewed research, (2) studies addressing encopresis and/or enuresis, (3) studies excluding typically developing children, and (4) studies evaluating toilet training during infancy. In addition to the study of Foxx and Azrin, only 4 publications met the above criteria. Toilet training procedures from each article were reviewed to determine which toilet training methods were similar to components described by Foxx and Azrin. Common training elements include increasing the frequency of learning opportunities through fluid loading and having differential consequences for being dry versus being wet and for voiding in the toilet versus elsewhere. There is little research on intensive toilet training of typically developing children. Practice sits and positive reinforcement for voids in the toilet are commonplace, consistent with the Foxx and Azrin protocol, whereas positive practice as a corrective procedure for wetting accidents often is omitted. Fluid loading and differential consequences for being dry versus being wet and for voiding in the toilet also are suggested procedures, consistent with the Foxx and Azrin protocol.

Development of a full-scale transmission testing procedure to evaluate advanced lubricants

NASA Technical Reports Server (NTRS)

Lewicki, David G.; Decker, Harry J.; Shimski, John T.

1992-01-01

Experimental tests were performed on the OH-58A helicopter main rotor transmission in the NASA Lewis 500-hp Helicopter Transmission Test Stand. The testing was part of a joint Navy/NASA/Army lubrication program. The objective of the program was to develop a separate lubricant for gearboxes and demonstrate an improved performance in life and load-carrying capacity. The goal of the experiments was to develop a testing procedure to fail certain transmission components using a MIL-L-23699 base reference oil, then run identical tests with improved lubricants and demonstrate performance. The tests were directed at failing components that the Navy has had problems with due to marginal lubrication. These failures included mast shaft bearing micropitting, sun gear and planet bearing fatigue, and spiral bevel gear scoring. A variety of tests were performed and over 900 hours of total run time accumulated for these tests. Some success was achieved in developing a testing procedure to produce sun gear and planet bearing fatigue failures. Only marginal success was achieved in producing mast shaft bearing micropitting and spiral bevel gear scoring.

Procedure for contact electrical resistance measurements as developed for use at Sandia National Laboratories

DOE Office of Scientific and Technical Information (OSTI.GOV)

Finch, J.L.

1994-06-01

Military Specifications call out general procedures and guidelines for conducting contact resistance measurements on chemical conversion coated panels. This paper deals with a test procedure developed at Sandia National Laboratories used to conduct contact electrical resistance on non-chromated conversion coated test panels. MIL-C-81706 {open_quotes}Chemical Conversion Materials For Coating Aluminum and Aluminum Alloys{close_quotes} was the reference specification used for guidance.

PREFACE: 15th Latin American Workshop on Plasma Physics (LAWPP 2014) and 21st IAEA TM on Research Using Small Fusion Devices (RUSFD)

NASA Astrophysics Data System (ADS)

Iván Vargas-Blanco, V.; Herrera-Velázquez, J. Julio E.

2015-03-01

Written contributions from participants of the Joint 15th Latin American Workshop on Plasma Physics (LAWPP 2014) - 21st IAEA Technical Meeting on Research Using Small Fusion Devices (21st IAEA TM RUSFD). The International Advisory Committees of the 15th Latin American Workshop on Plasma Physics (LAWPP 2014) and the 21st IAEA TM on Research Using Small Fusion Devices (RUSFD), agreed to carry out together this Joint LAWPP 2014 - 21st RUSFD in San José, Costa Rica, on 27-31 January 2014. The Joint LAWPP 2014 - 21st RUSFD meeting, organized by the Instituto Tecnológico de Costa Rica, Universidad Nacional de Costa Rica, and Ad Astra Rocket Company in collaboration with the International Atomic Energy Agency (IAEA). The Latin American Workshop on Plasma Physics (LAWPP) is a series of events which has been held periodically since 1982, with the purpose of providing a forum in which the research of the Latin American plasma physics community can be displayed, as well as fostering collaborations among plasma scientists within the region and with researchers from the rest of the world. Recognized plasma scientists from developed countries are specially invited to the meeting to present the state of the art on several "hot" topics related to plasma physics. It is an open meeting, with an International Advisory Committee, in which the working language is English. It was firstly held in 1982 in Cambuquira, Brazil, followed by workshops in Medellín, Colombia (1985), Santiago de Chile, Chile (1988), Buenos Aires, Argentina (1990), Mexico City, Mexico (1992), Foz do Iguaçu, Brazil (1994, combined with the International Congress on Plasma Physics (ICPP)), Caracas, Venezuela (1997), Tandil, Argentina (1998), La Serena, Chile (2000), Sao Pedro, Brazil (2003), Mexico City, Mexico (2005), Caracas, Venezuela (2007), Santiago de Chile, Chile (2010, combined with the ICPP) and Mar de Plata, Argentina (2011). The 21st IAEA TM on Research Using Small Fusion Devices is an ideal forum for

Development of a procedure for updating liquidated damage rates used in ALDOT construction contracts.

DOT National Transportation Integrated Search

2008-10-01

This research effort sought to develop statistically justifiable means for developing a : schedule of liquidated damage (LD) rates to be adopted by the Alabama Department of : Transportation (ALDOT). The procedure outlined is to be used to review and...

APPLICATION OF SOFTWARE QUALITY ASSURANCE CONCEPTS AND PROCEDURES TO ENVIORNMENTAL RESEARCH INVOLVING SOFTWARE DEVELOPMENT

EPA Science Inventory

As EPA’s environmental research expands into new areas that involve the development of software, quality assurance concepts and procedures that were originally developed for environmental data collection may not be appropriate. Fortunately, software quality assurance is a ...

Nuclear and isotopic techniques applied to supporting nutritional studies in East Asia and Pacific Countries: IAEA's contributions over 20 years.

PubMed

Kim, Seong-Ai; Miranda-da-Cruz, B; Mokhtar, Najat; Iyengar, Venkatesh

2004-01-01

The world's scientific community has recognized that isotopic techniques play a vital role in monitoring the effectiveness of nutrition intervention by providing precise data on absorption, bioavailablity and interaction of various micronutrients in a cost effective manner. The International Atomic Energy Agency (IAEA) has been supporting many such health related studies in Member States from developing countries using nuclear and isotopic methods for over 20 years. This report documents the Agency's support for a variety of projects in East Asia and Pacific countries to assess body composition, total energy expenditure, nutrient intake, osteoporosis, infection, vitamin and mineral bioavailability as well as food composition. The IAEA spent a total of 10,302,356 US dollars through Coordinated Research Projects (CRP) and Technical Cooperation Projects (TCP) over the past 20 years. Out of this only 2,732,802, US dollars or 26.5% was used by the East Asia and Pacific countries. While the participation of East Asia and Pacific countries was strong in CRPs and moderate in regional TCPs, they did not participate in national TCPs at all. The non-participation under national TCPs is a serious deficiency when compared with Latin American and African regions and therefore, more participation from the East Asia and Pacific countries in national TCPs is strongly encouraged in the future.

IAEA Coordinated Research Project on HTGR Reactor Physics, Thermal-hydraulics and Depletion Uncertainty Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Strydom, Gerhard; Bostelmann, F.

The continued development of High Temperature Gas Cooled Reactors (HTGRs) requires verification of HTGR design and safety features with reliable high fidelity physics models and robust, efficient, and accurate codes. The predictive capability of coupled neutronics/thermal-hydraulics and depletion simulations for reactor design and safety analysis can be assessed with sensitivity analysis (SA) and uncertainty analysis (UA) methods. Uncertainty originates from errors in physical data, manufacturing uncertainties, modelling and computational algorithms. (The interested reader is referred to the large body of published SA and UA literature for a more complete overview of the various types of uncertainties, methodologies and results obtained).more » SA is helpful for ranking the various sources of uncertainty and error in the results of core analyses. SA and UA are required to address cost, safety, and licensing needs and should be applied to all aspects of reactor multi-physics simulation. SA and UA can guide experimental, modelling, and algorithm research and development. Current SA and UA rely either on derivative-based methods such as stochastic sampling methods or on generalized perturbation theory to obtain sensitivity coefficients. Neither approach addresses all needs. In order to benefit from recent advances in modelling and simulation and the availability of new covariance data (nuclear data uncertainties) extensive sensitivity and uncertainty studies are needed for quantification of the impact of different sources of uncertainties on the design and safety parameters of HTGRs. Only a parallel effort in advanced simulation and in nuclear data improvement will be able to provide designers with more robust and well validated calculation tools to meet design target accuracies. In February 2009, the Technical Working Group on Gas-Cooled Reactors (TWG-GCR) of the International Atomic Energy Agency (IAEA) recommended that the proposed Coordinated Research Program

Endoscopic surgery and telemedicine in microgravity: developing contingency procedures for exploratory class spaceflight.

PubMed

Jones, J A; Johnston, S; Campbell, M; Miles, B; Billica, R

1999-05-01

The risk of a urinary calculus during an extended duration mission into the reduced gravity environment of space is significant. For medical operations to develop a comprehensive strategy for the spaceflight stone risk, both preventive countermeasures and contingency management (CM) plans must be included. A feasibility study was conducted to demonstrate the potential CM technique of endoscopic ureteral stenting with ultrasound guidance for the possible in-flight urinary calculus contingency. The procedure employed the International Space Station/Human Research Facility ultrasound unit for guide wire and stent localization, a flexible cystoscope for visual guidance, and banded, biocompatible soft ureteral stents to successfully stent porcine ureters bilaterally in zero gravity (0g). The study demonstrated that downlinked endoscopic surgical and ultrasound images obtained in 0g are comparable in quality to 1g images, and therefore are useful for diagnostic clinical utility via telemedicine transmission. In order to be successful, surgical procedures in 0g require excellent positional stability of the operating surgeon, assistant, and patient, relative to one another. The technological development of medical procedures for long-duration spaceflight contingencies may lead to improved terrestrial patient care methodology and subsequently reduced morbidity.

Endoscopic surgery and telemedicine in microgravity: developing contingency procedures for exploratory class spaceflight

NASA Technical Reports Server (NTRS)

Jones, J. A.; Johnston, S.; Campbell, M.; Miles, B.; Billica, R.

1999-01-01

OBJECTIVES: The risk of a urinary calculus during an extended duration mission into the reduced gravity environment of space is significant. For medical operations to develop a comprehensive strategy for the spaceflight stone risk, both preventive countermeasures and contingency management (CM) plans must be included. METHODS: A feasibility study was conducted to demonstrate the potential CM technique of endoscopic ureteral stenting with ultrasound guidance for the possible in-flight urinary calculus contingency. The procedure employed the International Space Station/Human Research Facility ultrasound unit for guide wire and stent localization, a flexible cystoscope for visual guidance, and banded, biocompatible soft ureteral stents to successfully stent porcine ureters bilaterally in zero gravity (0g). RESULTS: The study demonstrated that downlinked endoscopic surgical and ultrasound images obtained in 0g are comparable in quality to 1g images, and therefore are useful for diagnostic clinical utility via telemedicine transmission. CONCLUSIONS: In order to be successful, surgical procedures in 0g require excellent positional stability of the operating surgeon, assistant, and patient, relative to one another. The technological development of medical procedures for long-duration spaceflight contingencies may lead to improved terrestrial patient care methodology and subsequently reduced morbidity.

Development and application of an optimization procedure for flutter suppression using the aerodynamic energy concept

NASA Technical Reports Server (NTRS)

Nissim, E.; Abel, I.

1978-01-01

An optimization procedure is developed based on the responses of a system to continuous gust inputs. The procedure uses control law transfer functions which have been partially determined by using the relaxed aerodynamic energy approach. The optimization procedure yields a flutter suppression system which minimizes control surface activity in a gust environment. The procedure is applied to wing flutter of a drone aircraft to demonstrate a 44 percent increase in the basic wing flutter dynamic pressure. It is shown that a trailing edge control system suppresses the flutter instability over a wide range of subsonic mach numbers and flight altitudes. Results of this study confirm the effectiveness of the relaxed energy approach.

15 years in promoting the use of isotopic and nuclear technique for combating land degradation and soil erosion: the contribution of the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture

NASA Astrophysics Data System (ADS)

Mabit, Lionel; Toloza, Arsenio; Heng, Lee

2017-04-01

The world population will exceed 9 billion by the year 2050 and food production will need to be approximately doubled to meet this crucial demand. Most of this increase will occur in developing countries, where the majority of the population depends on agriculture and their land for their livelihoods. Reports from the Intergovernmental Panel on Climate Change (IPCC) predicted negative impact of climate change, threatening global food security. In addition, the intensification of agricultural activities has increased pressure on land and water resources, resulting in different forms of soil degradation, of which soil erosion and associated sedimentation are worsening. Worldwide economic costs of agricultural soil loss and associated sedimentation downstream have been estimated at US 400 billion per year. As a result of climate change, world average soil erosion is expected to further increase significantly. Adapting to climate change requires agricultural soil and water management practices that make agricultural production systems resilient to drought, floods and land degradation, to enhance the conservation of the natural resource base for sustainable upland farming. These current concerns with ensuring sustainable use and management of agroecosystems create an urgent need for reliable quantitative data on the extent and magnitude of soil resource degradation over several spatial and time scales to formulate sound policies and management measures. Integrated isotopic approaches can help in targeting adapted and effective soil-water conservation measures to control soil degradation and therefore contribute to positive feedback mechanisms to mitigate climate change impact on soil and water resources. Set up 60 years ago as the world's centre for cooperation in the nuclear field, the International Atomic Energy Agency (IAEA) promotes the safe, secure and peaceful use of nuclear technologies. Since the end of the 1990s, the Joint FAO/IAEA Division of Nuclear

Designing Flightdeck Procedures

NASA Technical Reports Server (NTRS)

Barshi, Immanuel; Mauro, Robert; Degani, Asaf; Loukopoulou, Loukia

2016-01-01

The primary goal of this document is to provide guidance on how to design, implement, and evaluate flight deck procedures. It provides a process for developing procedures that meet clear and specific requirements. This document provides a brief overview of: 1) the requirements for procedures, 2) a process for the design of procedures, and 3) a process for the design of checklists. The brief overview is followed by amplified procedures that follow the above steps and provide details for the proper design, implementation and evaluation of good flight deck procedures and checklists.

Considerations Related To Human Intrusion In The Context Of Disposal Of Radioactive Waste-The IAEA HIDRA Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seitz, Roger; Kumano, Yumiko; Bailey, Lucy

2014-01-09

The principal approaches for management of radioactive waste are commonly termed ‘delay and decay’, ‘concentrate and contain’ and ‘dilute and disperse’. Containing the waste and isolating it from the human environment, by burying it, is considered to increase safety and is generally accepted as the preferred approach for managing radioactive waste. However, this approach results in concentrated sources of radioactive waste contained in one location, which can pose hazards should the facility be disrupted by human action in the future. The International Commission on Radiological Protection (ICRP), International Atomic Energy Agency (IAEA), and Organization for Economic Cooperation and Development/Nuclear Energymore » Agency (OECD/NEA) agree that some form of inadvertent human intrusion (HI) needs to be considered to address the potential consequences in the case of loss of institutional control and loss of memory of the disposal facility. Requirements are reflected in national regulations governing radioactive waste disposal. However, in practice, these requirements are often different from country to country, which is then reflected in the actual implementation of HI as part of a safety case. The IAEA project on HI in the context of Disposal of RadioActive waste (HIDRA) has been started to identify potential areas for improved consistency in consideration of HI. The expected outcome is to provide recommendations on how to address human actions in the safety case in the future, and how the safety case may be used to demonstrate robustness and optimize siting, design and waste acceptance criteria within the context of a safety case.« less

Dosimetric inter-institutional comparison in European radiotherapy centres: Results of IAEA supported treatment planning system audit.

PubMed

Gershkevitsh, Eduard; Pesznyak, Csilla; Petrovic, Borislava; Grezdo, Joseph; Chelminski, Krzysztof; do Carmo Lopes, Maria; Izewska, Joanna; Van Dyk, Jacob

2014-05-01

One of the newer audit modalities operated by the International Atomic Energy Agency (IAEA) involves audits of treatment planning systems (TPS) in radiotherapy. The main focus of the audit is the dosimetry verification of the delivery of a radiation treatment plan for three-dimensional (3D) conformal radiotherapy using high energy photon beams. The audit has been carried out in eight European countries - Estonia, Hungary, Latvia, Lithuania, Serbia, Slovakia, Poland and Portugal. The corresponding results are presented. The TPS audit reviews the dosimetry, treatment planning and radiotherapy delivery processes using the 'end-to-end' approach, i.e. following the pathway similar to that of the patient, through imaging, treatment planning and dose delivery. The audit is implemented at the national level with IAEA assistance. The national counterparts conduct the TPS audit at local radiotherapy centres through on-site visits. TPS calculated doses are compared with ion chamber measurements performed in an anthropomorphic phantom for eight test cases per algorithm/beam. A set of pre-defined agreement criteria is used to analyse the performance of TPSs. TPS audit was carried out in 60 radiotherapy centres. In total, 190 data sets (combination of algorithm and beam quality) have been collected and reviewed. Dosimetry problems requiring interventions were discovered in about 10% of datasets. In addition, suboptimal beam modelling in TPSs was discovered in a number of cases. The TPS audit project using the IAEA methodology has verified the treatment planning system calculations for 3D conformal radiotherapy in a group of radiotherapy centres in Europe. It contributed to achieving better understanding of the performance of TPSs and helped to resolve issues related to imaging, dosimetry and treatment planning.

Language Learning of Children with Typical Development Using a Deductive Metalinguistic Procedure

ERIC Educational Resources Information Center

Finestack, Lizbeth H.

2014-01-01

Purpose: In the current study, the author aimed to determine whether 4- to 6-year-old typically developing children possess requisite problem-solving and language abilities to produce, generalize, and retain a novel verb inflection when taught using an explicit, deductive teaching procedure. Method: Study participants included a cross-sectional…

Development of an analytical procedure to study linear alkylbenzenesulphonate (LAS) degradation in sewage sludge-amended soils.

PubMed

Comellas, L; Portillo, J L; Vaquero, M T

1993-12-24

A procedure for determining linear alkylbenzenesulphonates (LASs) in sewage sludge and amended soils has been developed. Extraction by sample treatment with 0.5 M potassium hydroxide in methanol and reflux was compared with a previously described extraction procedure in Soxhlet with methanol and solid sodium hydroxide in the sample. Repeatability results were similar with savings in extraction time, solvents and evaporation time. A clean-up method involving a C18 cartridge has been developed. Analytes were quantified by a reversed-phase HPLC method with UV and fluorescence detectors. Recoveries obtained were higher than 84%. The standing procedure was applied to high doses of sewage sludge-amended soils (15%) with increasing quantities of added LASs. Degradation data for a 116-day period are presented.

Motor Development: Manual of Alternative Procedures.

ERIC Educational Resources Information Center

McCormack, James E.

The manual of alternative procedures for teaching handicapped children focuses on programming, planning, and implementing training in the gross motor (posture, limb control, locomotion) and fine motor (facial, digital) skills. The manual consists of the following sections: specific teaching tactics commonly used in motor training stiuations…

R-Matrix Codes for Charged-Particle Induced Reactions in the Resolved Resonance Region (3), Summary Report of an IAEA Consultants' Meeting IAEA Headquarters, Vienna, Austria, 28-30 June 2017

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leeb, Helmut; Dimitriou, Paraskevi; Thompson, Ian

A Consultants Meeting was held at the IAEA Headquarters, from 28 to 30 June 2017, to discuss the results of a test exercise that had been defined and assigned to all participants of the previous meeting held in December 2016. Five codes were used in this exercise: AMUR, AZURE2, RAC, SFRESCO and SAMMY. The results obtained from these codes were compared and further actions were proposed. Participants’ presentations and technical discussions, as well as proposed additional actions have been summarized in this report.

Application of inductively coupled plasma sector field mass spectrometry for low-level environmental americium-241 analysis.

PubMed

Varga, Zsolt

2007-03-28

An improved and novel sample preparation method for (241)Am analysis by inductively coupled plasma sector field mass spectrometry has been developed. The procedure involves a selective CaF(2) pre-concentration followed by an extraction chromatographic separation using TRU resin. The achieved absolute detection limit of 0.86 fg (0.11 mBq) is comparable to that of alpha spectrometry (0.1 mBq) and suitable for low-level environmental measurements. Analysis of different kinds of environmental standard reference materials (IAEA-384--Fangataufa lagoon sediment, IAEA-385--Irish Sea sediment and IAEA-308--Mixed seaweed from the Mediterranean Sea) and alpha spectrometry were used to validate the procedure. The chemical recovery of sample preparation ranged between 72 and 94%. The results obtained are in good agreement with reference values and those measured by alpha spectrometry. The proposed method offers a rapid and less labor-intensive possibility for environmental (241)Am analysis than the conventionally applied radioanalytical techniques.

TH-EF-204-02: Small Field Radiation Therapy: Physics and Recent Recommendations From IAEA and ICRU

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seuntjens, J.

Joanna E. Cygler, Jan Seuntjens, J. Daniel Bourland, M. Saiful Huq, Josep Puxeu Vaque, Daniel Zucca Aparicio, Tatiana Krylova, Yuri Kirpichev, Eric Ford, Caridad Borras Stereotactic Radiation Therapy (SRT) utilizes small static and dynamic (IMRT) fields, to successfully treat malignant and benign diseases using techniques such as Stereotactic Radiosurgery (SRS) and Stereotactic Body Radiation Therapy (SBRT). SRT is characterized by sharp dose gradients for individual fields and their resultant dose distributions. For appropriate targets, small field radiotherapy offers improved treatment quality by allowing better sparing of organs at risk while delivering the prescribed target dose. Specialized small field treatment deliverymore » systems, such as robotic-controlled linear accelerators, gamma radiosurgery units, and dynamic arc linear accelerators may utilize rigid fixation, image guidance, and tumor tracking, to insure precise dose delivery to static or moving targets. However, in addition to great advantages, small field delivery techniques present special technical challenges for dose calibration due to unique geometries and small field sizes not covered by existing reference dosimetry protocols such as AAPM TG-51 or IAEA TRS 398. In recent years extensive research has been performed to understand small field dosimetry and measurement instrumentation. AAPM, IAEA and ICRU task groups are expected to provide soon recommendations on the dosimetry of small radiation fields. In this symposium we will: 1] discuss the physics, instrumentation, methodologies and challenges for small field radiation dose measurements; 2] review IAEA and ICRU recommendations on prescribing, recording and reporting of small field radiation therapy; 3] discuss selected clinical applications and technical aspects for specialized image-guided, small field, linear accelerator based treatment techniques such as IMRT and SBRT. Learning Objectives: To learn the physics of small fields in

A dosimetry study comparing NCS report-5, IAEA TRS-381, AAPM TG-51 and IAEA TRS-398 in three clinical electron beam energies

NASA Astrophysics Data System (ADS)

Palmans, Hugo; Nafaa, Laila; de Patoul, Nathalie; Denis, Jean-Marc; Tomsej, Milan; Vynckier, Stefaan

2003-05-01

New codes of practice for reference dosimetry in clinical high-energy photon and electron beams have been published recently, to replace the air kerma based codes of practice that have determined the dosimetry of these beams for the past twenty years. In the present work, we compared dosimetry based on the two most widespread absorbed dose based recommendations (AAPM TG-51 and IAEA TRS-398) with two air kerma based recommendations (NCS report-5 and IAEA TRS-381). Measurements were performed in three clinical electron beam energies using two NE2571-type cylindrical chambers, two Markus-type plane-parallel chambers and two NACP-02-type plane-parallel chambers. Dosimetry based on direct calibrations of all chambers in 60Co was investigated, as well as dosimetry based on cross-calibrations of plane-parallel chambers against a cylindrical chamber in a high-energy electron beam. Furthermore, 60Co perturbation factors for plane-parallel chambers were derived. It is shown that the use of 60Co calibration factors could result in deviations of more than 2% for plane-parallel chambers between the old and new codes of practice, whereas the use of cross-calibration factors, which is the first recommendation in the new codes, reduces the differences to less than 0.8% for all situations investigated here. The results thus show that neither the chamber-to-chamber variations, nor the obtained absolute dose values are significantly altered by changing from air kerma based dosimetry to absorbed dose based dosimetry when using calibration factors obtained from the Laboratory for Standard Dosimetry, Ghent, Belgium. The values of the 60Co perturbation factor for plane-parallel chambers (katt . km for the air kerma based and pwall for the absorbed dose based codes of practice) that are obtained from comparing the results based on 60Co calibrations and cross-calibrations are within the experimental uncertainties in agreement with the results from other investigators.

29 CFR 1956.23 - Procedures for certification of completion of development and determination on application of...

Code of Federal Regulations, 2010 CFR

2010-07-01

... and determination on application of criteria. 1956.23 Section 1956.23 Labor Regulations Relating to... Approval Procedures § 1956.23 Procedures for certification of completion of development and determination... basis of actual operations, the criteria set forth in §§ 1956.10 and 1956.11 of this part are being...

Development of static system procedures to study aquatic biofilms and their responses to disinfection and invading species

NASA Technical Reports Server (NTRS)

Smithers, G. A.

1992-01-01

The microbial ecology facility in the Analytical and Physical Chemistry Branch at Marshall Space Flight Center is tasked with anticipation of potential microbial problems (and opportunities to exploit microorganisms) which may occur in partially closed systems such as space station/vehicles habitats and in water reclamation systems therein, with particular emphasis on the degradation of materials. Within this context, procedures for microbial biofilm research are being developed. Reported here is the development of static system procedures to study aquatic biofilms and their responses to disinfection and invading species. Preliminary investigations have been completed. As procedures are refined, it will be possible to focus more closely on the elucidation of biofilm phenomena.

Dual-systems and the development of reasoning: competence-procedural systems.

PubMed

Overton, Willis F; Ricco, Robert B

2011-03-01

Dual-system, dual-process, accounts of adult cognitive processing are examined in the context of a self-organizing relational developmental systems approaches to cognitive growth. Contemporary adult dual-process accounts describe a linear architecture of mind entailing two split-off, but interacting systems; a domain general, content-free 'analytic' system (system 2) and a domain specific highly contextualized 'heuristic' system (system 1). In the developmental literature on deductive reasoning, a similar distinction has been made between a domain general competence (reflective, algorithmic) system and a domain specific procedural system. In contrast to the linear accounts offered by empiricist, nativist, and/or evolutionary explanations, the dual competence-procedural developmental perspective argues that the mature systems emerge through developmental transformations as differentiations and intercoordinations of an early relatively undifferentiated action matrix. This development, whose microscopic mechanism is action-in-the-world, is characterized as being embodied, nonlinear, and epigenetic. WIREs Cogni Sci 2011 2 231-237 DOI: 10.1002/wcs.120 For further resources related to this article, please visit the WIREs website. © 2010 John Wiley & Sons, Ltd.

Civil Procedure.

ERIC Educational Resources Information Center

Byer, Robert

1997-01-01

Briefly reviews the historical development of civil procedure (the rules that dictate how a civil case can proceed through the courts) and identifies some of its main components. Discusses procedures such as subject matter jurisdiction, personal jurisdiction, venue, discovery, motions practice, pleadings, pretrial conference, and trials. (MJP)

Developing technical expertise in emergency medicine--the role of simulation in procedural skill acquisition.

PubMed

Wang, Ernest E; Quinones, Joshua; Fitch, Michael T; Dooley-Hash, Suzanne; Griswold-Theodorson, Sharon; Medzon, Ron; Korley, Frederick; Laack, Torrey; Robinett, Adam; Clay, Lamont

2008-11-01

Developing technical expertise in medical procedures is an integral component of emergency medicine (EM) practice and training. This article is the work of an expert panel composed of members from the Society for Academic Emergency Medicine (SAEM) Interest Group, the SAEM Technology in Medical Education Committee, and opinions derived from the May 2008 Academic Emergency Medicine Consensus Conference, "The Science of Simulation in Healthcare." The writing group reviewed the simulation literature on procedures germane to EM training, virtual reality training, and instructional learning theory as it pertains to skill acquisition and procedural skills decay. The authors discuss the role of simulation in teaching technical expertise, identify training conditions that lead to effective learning, and provide recommendations for future foci of research.

Climate change and landscape development in post-closure safety assessment of solid radioactive waste disposal: Results of an initiative of the IAEA.

PubMed

Lindborg, T; Thorne, M; Andersson, E; Becker, J; Brandefelt, J; Cabianca, T; Gunia, M; Ikonen, A T K; Johansson, E; Kangasniemi, V; Kautsky, U; Kirchner, G; Klos, R; Kowe, R; Kontula, A; Kupiainen, P; Lahdenperä, A-M; Lord, N S; Lunt, D J; Näslund, J-O; Nordén, M; Norris, S; Pérez-Sánchez, D; Proverbio, A; Riekki, K; Rübel, A; Sweeck, L; Walke, R; Xu, S; Smith, G; Pröhl, G

2018-03-01

The International Atomic Energy Agency has coordinated an international project addressing climate change and landscape development in post-closure safety assessments of solid radioactive waste disposal. The work has been supported by results of parallel on-going research that has been published in a variety of reports and peer reviewed journal articles. The project is due to be described in detail in a forthcoming IAEA report. Noting the multi-disciplinary nature of post-closure safety assessments, here, an overview of the work is given to provide researchers in the broader fields of radioecology and radiological safety assessment with a review of the work that has been undertaken. It is hoped that such dissemination will support and promote integrated understanding and coherent treatment of climate change and landscape development within an overall assessment process. The key activities undertaken in the project were: identification of the key processes that drive environmental change (mainly those associated with climate and climate change), and description of how a relevant future may develop on a global scale; development of a methodology for characterising environmental change that is valid on a global scale, showing how modelled global changes in climate can be downscaled to provide information that may be needed for characterising environmental change in site-specific assessments, and illustrating different aspects of the methodology in a number of case studies that show the evolution of site characteristics and the implications for the dose assessment models. Overall, the study has shown that quantitative climate and landscape modelling has now developed to the stage that it can be used to define an envelope of climate and landscape change scenarios at specific sites and under specific greenhouse-gas emissions assumptions that is suitable for use in quantitative post-closure performance assessments. These scenarios are not predictions of the future, but

WE-AB-213-00: Developments in International Medical Physics Collaborations in Africa and Latin America

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

complexity of the radiological procedures and the associated radiation risks”. Details on how these requirements can be carried out in resource-limited settings will be described. IAEA support to medical physics in Africa and Latin America: achievements and challenges Ahmed Meghzifene (IAEA) Shortage of clinically qualified medical physicists in radiotherapy and imaging, insufficient and inadequate education and training programs, as well as a lack of professional recognition were identified as the main issues to be addressed by the IAEA. The IAEA developed a series of integrated projects aiming specifically at promoting the essential role of medical physicists in health care, developing harmonized guidelines on dosimetry and quality assurance, and supporting education and clinical training programs. The unique feature of the IAEA approach is support it provides for implementation of guidelines and education programs in Member States through its technical cooperation project. The presentation will summarize IAEA support to Latin America and Africa in the field of medical physics and will highlight how the new International Basic Safety Standards are expected to impact the medical physics practice in low and middle income countries. Learning Objectives: Learn about the shortage of qualified Medical Physicists in Africa and Latin America. Understand the reasons of this shortage. Learn about the ways to improve the situation and AAPM role in this process.« less

Electronic Procedures for Medical Operations

NASA Technical Reports Server (NTRS)

2015-01-01

Electronic procedures are replacing text-based documents for recording the steps in performing medical operations aboard the International Space Station. S&K Aerospace, LLC, has developed a content-based electronic system-based on the Extensible Markup Language (XML) standard-that separates text from formatting standards and tags items contained in procedures so they can be recognized by other electronic systems. For example, to change a standard format, electronic procedures are changed in a single batch process, and the entire body of procedures will have the new format. Procedures can be quickly searched to determine which are affected by software and hardware changes. Similarly, procedures are easily shared with other electronic systems. The system also enables real-time data capture and automatic bookmarking of current procedure steps. In Phase II of the project, S&K Aerospace developed a Procedure Representation Language (PRL) and tools to support the creation and maintenance of electronic procedures for medical operations. The goal is to develop these tools in such a way that new advances can be inserted easily, leading to an eventual medical decision support system.

To Develop and Test Improved Procedures for the Development and Distribution of Quality Individualized Mediated Instructional Materials in Vocational Education. Final Report.

ERIC Educational Resources Information Center

State Fair Community Coll., Sedalia, MO.

Five objectives are reported for a project to develop and test effective procedures for designing, field testing, reproducing, and disseminating individualized mediated instructional materials: (1) improvement of teacher input, (2) development of individualized instruction modules, (3) development of methodology for evaluating the effectiveness of…

Extended Development Procedure EDeP Advanced Reference Manual.

DTIC Science & Technology

1982-11-01

approach or combination of approaches. * The necessary mtials might include job aides on peer tutoring procedures, flashcards , lesson materials, etc. * The...should be suitable for one-to-one use. * A special form of a particular medium may be necessary, such as flashcards instead of printed text materials...to read, or holding a flashcard with a math problem on it indicates that the learner should solve the problem. Coaching: - A procedure can be devised

An Overview of Models of Speaking Performance and Its Implications for the Development of Procedural Framework for Diagnostic Speaking Tests

ERIC Educational Resources Information Center

Zhao, Zhongbao

2013-01-01

This paper aims at developing a procedural framework for the development and validation of diagnostic speaking tests. The researcher reviews the current available models of speaking performance, analyzes the distinctive features and then points out the implications for the development of a procedural framework for diagnostic speaking tests. On…

Information Exchange Procedures. Outcomes Study Procedures. Technical Report No. 66.

ERIC Educational Resources Information Center

Byers, Maureen

The Information Exchange Procedures (IEP) developed by the National Center for Higher Education Management Systems (NCHEMS) are a set of standard definitions and procedures for collecting information about disciplines and student degree programs, outcomes of instructional programs, and general institutional characteristics. A fundamental purpose…

29 CFR 37.77 - Who is responsible for developing and publishing complaint processing procedures for service...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 1 2010-07-01 2010-07-01 true Who is responsible for developing and publishing complaint... (WIA) Compliance Procedures § 37.77 Who is responsible for developing and publishing complaint... State's Methods of Administration, must develop and publish, on behalf of its service providers, the...

People's Need for Additional Job Training: Development and Evaluation of an Assessment Procedure.

ERIC Educational Resources Information Center

Copa, George H.; Maurice, Clyde F.

A procedure was developed and evaluated for assessing the self-perceived educational needs of people as one input to the process of planning, approving, and implementing relevant educational programs. The method of data collection involved selecting samples of people by randomly selecting households in a given geographic area, and then contacting…

Development of a standardized training course for laparoscopic procedures using Delphi methodology.

PubMed

Bethlehem, Martijn S; Kramp, Kelvin H; van Det, Marc J; ten Cate Hoedemaker, Henk O; Veeger, Nicolaas J G M; Pierie, Jean Pierre E N

2014-01-01

Content, evaluation, and certification of laparoscopic skills and procedure training lack uniformity among different hospitals in The Netherlands. Within the process of developing a new regional laparoscopic training curriculum, a uniform and transferrable curriculum was constructed for a series of laparoscopic procedures. The aim of this study was to determine regional expert consensus regarding the key steps for laparoscopic appendectomy and cholecystectomy using Delphi methodology. Lists of suggested key steps for laparoscopic appendectomy and cholecystectomy were created using surgical textbooks, available guidelines, and local practice. A total of 22 experts, working for teaching hospitals throughout the region, were asked to rate the suggested key steps for both procedures on a Likert scale from 1-5. Consensus was reached with Crohnbach's α ≥ 0.90. Of the 22 experts, 21 completed and returned the survey (95%). Data analysis already showed consensus after the first round of Delphi on the key steps for laparoscopic appendectomy (Crohnbach's α = 0.92) and laparoscopic cholecystectomy (Crohnbach's α = 0.90). After the second round, 15 proposed key steps for laparoscopic appendectomy and 30 proposed key steps for laparoscopic cholecystectomy were rated as important (≥4 by at least 80% of the expert panel). These key steps were used for the further development of the training curriculum. By using the Delphi methodology, regional consensus was reached on the key steps for laparoscopic appendectomy and cholecystectomy. These key steps are going to be used for standardized training and evaluation purposes in a new regional laparoscopic curriculum. Copyright © 2014 Association of Program Directors in Surgery. Published by Elsevier Inc. All rights reserved.

Pollutant Assessments Group procedures manual: Volume 2, Technical procedures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-03-01

This is volume 2 of the manuals that describes the technical procedures currently in use by the Pollution Assessments Group. This manual incorporates new developments in hazardous waste assessment technology and administrative policy. Descriptions of the equipment, procedures and operations of such things as radiation detection, soil sampling, radionuclide monitoring, and equipment decontamination are included in this manual. (MB)

Development of a diagnosis- and procedure-based risk model for 30-day outcome after pediatric cardiac surgery.

PubMed

Crowe, Sonya; Brown, Kate L; Pagel, Christina; Muthialu, Nagarajan; Cunningham, David; Gibbs, John; Bull, Catherine; Franklin, Rodney; Utley, Martin; Tsang, Victor T

2013-05-01

The study objective was to develop a risk model incorporating diagnostic information to adjust for case-mix severity during routine monitoring of outcomes for pediatric cardiac surgery. Data from the Central Cardiac Audit Database for all pediatric cardiac surgery procedures performed in the United Kingdom between 2000 and 2010 were included: 70% for model development and 30% for validation. Units of analysis were 30-day episodes after the first surgical procedure. We used logistic regression for 30-day mortality. Risk factors considered included procedural information based on Central Cardiac Audit Database "specific procedures," diagnostic information defined by 24 "primary" cardiac diagnoses and "univentricular" status, and other patient characteristics. Of the 27,140 30-day episodes in the development set, 25,613 were survivals, 834 were deaths, and 693 were of unknown status (mortality, 3.2%). The risk model includes procedure, cardiac diagnosis, univentricular status, age band (neonate, infant, child), continuous age, continuous weight, presence of non-Down syndrome comorbidity, bypass, and year of operation 2007 or later (because of decreasing mortality). A risk score was calculated for 95% of cases in the validation set (weight missing in 5%). The model discriminated well; the C-index for validation set was 0.77 (0.81 for post-2007 data). Removal of all but procedural information gave a reduced C-index of 0.72. The model performed well across the spectrum of predicted risk, but there was evidence of underestimation of mortality risk in neonates undergoing operation from 2007. The risk model performs well. Diagnostic information added useful discriminatory power. A future application is risk adjustment during routine monitoring of outcomes in the United Kingdom to assist quality assurance. Copyright © 2013 The American Association for Thoracic Surgery. Published by Mosby, Inc. All rights reserved.

Development of a safety evaluation procedure for identifying high-risk signalized intersections in the Virginia Department of Transportation's Northern Virginia district.

DOT National Transportation Integrated Search

2007-01-01

This research was undertaken to develop an evaluation procedure to identify high-risk four-legged signalized intersections in VDOT's Northern Virginia district by traffic movements and times of day. By using the developed procedure, traffic engineers...

Development of unauthorized airborne emission source identification procedure

NASA Astrophysics Data System (ADS)

Shtripling, L. O.; Bazhenov, V. V.; Varakina, N. S.; Kupriyanova, N. P.

2018-01-01

The paper presents the procedure for searching sources of unauthorized airborne emissions. To make reasonable regulation decisions on airborne pollutant emissions and to ensure the environmental safety of population, the procedure provides for the determination of a pollutant mass emission value from the source being the cause of high pollution level and the search of a previously unrecognized contamination source in a specified area. To determine the true value of mass emission from the source, the minimum of the mean-root-square mismatch criterion between the computed and measured pollutant concentration in the given location is used.

Development of Procedures for Generating Alternative Allied Health Manpower Requirements and Supply Estimates.

ERIC Educational Resources Information Center

Applied Management Sciences, Inc., Silver Spring, MD.

This report presents results of a project to assess the adequacy of existing data sources on the supply of 21 allied health occupations in order to develop improved data collection strategies and improved procedures for estimation of manpower needs. Following an introduction, chapter 2 provides a discussion of the general phases of the project and…

The impact of the International Atomic Energy Agency (IAEA) program on radiation and tissue banking in Indonesia.

PubMed

Hilmy, Nazly; Manjas, Menkher; Ferdiansyah; Abbas, Basril; Morales Pedraza, Jorge

2009-05-01

In 1986, the National Nuclear Energy Agency (Batan) in Jakarta started the research and development for the setting up of a tissue bank (Batan Research Tissue Bank/BRTB) by preserving fresh amnion or fetal membranes by lyophilisation and then sterilising by gamma irradiation. During the period of 1990 and 2000, three more tissue banks were set up, i.e., Biomaterial Centre in Surabaya, Jamil Tissue Bank in Padang, and Sitanala Tissue Bank in Tangerang. In 1994, BRTB produced bone allografts. The banks established under the IAEA program concentrated its work on the production of amnion, bone and soft tissues allografts, as well as bone xenografts. These tissues (allografts and xenografts) were sterilised using gamma irradiation (about 90%) and the rest were sterilized by ETO and those products have been used in the treatment of patients at more than 50 hospitals in Indonesia. In 2004, those tissue banks produced 8,500 grafts and 5,000 of them were amnion grafts for eye treatment and wound dressing. All of those grafts were used for patients as well as for research. In 2006, the production increased to 9,000 grafts. Although the capacity of those banks can produce more grafts, we are facing problems on getting raw materials from suitable donors. To fulfill the demand of bone grafts we also produced bone xenografts. The impact of the IAEA program in tissue banking activities in Indonesia can be summarised as follows: to support the national program on importing substitutes for medical devices. The price of imported tissues are between US$ 50 and US$ 6,000 per graft. Local tissue bank can produce tissues with the same quality with the price for about 10-30% of the imported tissues.

Runway Rubber Removal Specification Development: Field Evaluation Procedures Development.

DTIC Science & Technology

1984-07-01

removal was sufficient enough to restore full pave- ment skid resistance (based on tests with a DBV). With regard to high-pressure water rubber ...over a test surface, the rubber slider resists motion-. The force, parallel to the test surface, which acts on the slider registers an output on a dial...PROCEDURE 1. Check rubber shoe for wear . Replace when the edge is worn by more than 3/16 in as measured with a rule laid flat across the slider width. 2

Weather analysis and interpretation procedures developed for the US/Canada wheat and barley exploratory experiment

NASA Technical Reports Server (NTRS)

Trenchard, M. H. (Principal Investigator)

1980-01-01

Procedures and techniques for providing analyses of meteorological conditions at segments during the growing season were developed for the U.S./Canada Wheat and Barley Exploratory Experiment. The main product and analysis tool is the segment-level climagraph which depicts temporally meteorological variables for the current year compared with climatological normals. The variable values for the segment are estimates derived through objective analysis of values obtained at first-order station in the region. The procedures and products documented represent a baseline for future Foreign Commodity Production Forecasting experiments.

Model of Procedure Usage – Results from a Qualitative Study to Inform Design of Computer-Based Procedures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johanna H Oxstrand; Katya L Le Blanc

The nuclear industry is constantly trying to find ways to decrease the human error rate, especially the human errors associated with procedure use. As a step toward the goal of improving procedure use performance, researchers, together with the nuclear industry, have been looking at replacing the current paper-based procedures with computer-based procedure systems. The concept of computer-based procedures is not new by any means; however most research has focused on procedures used in the main control room. Procedures reviewed in these efforts are mainly emergency operating procedures and normal operating procedures. Based on lessons learned for these previous efforts wemore » are now exploring a more unknown application for computer based procedures - field procedures, i.e. procedures used by nuclear equipment operators and maintenance technicians. The Idaho National Laboratory, the Institute for Energy Technology, and participants from the U.S. commercial nuclear industry are collaborating in an applied research effort with the objective of developing requirements and specifications for a computer-based procedure system to be used by field operators. The goal is to identify the types of human errors that can be mitigated by using computer-based procedures and how to best design the computer-based procedures to do this. The underlying philosophy in the research effort is “Stop – Start – Continue”, i.e. what features from the use of paper-based procedures should we not incorporate (Stop), what should we keep (Continue), and what new features or work processes should be added (Start). One step in identifying the Stop – Start – Continue was to conduct a baseline study where affordances related to the current usage of paper-based procedures were identified. The purpose of the study was to develop a model of paper based procedure use which will help to identify desirable features for computer based procedure prototypes. Affordances such as note taking

Developing an SSAC Self-Assessment Tool for Operators and Regulators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frazar, Sarah L.; Innes-Jones, Gemma; Hamilton, Ian

Enabling an SSAC to understand why it is performing inefficiently can help it allocate resources more effectively to better support IAEA safeguards implementation. In collaboration with international consulting firm, Environmental Resources Management (ERM) and a U.S. based nuclear fuel cycle facility, the Pacific Northwest National Laboratory (PNNL) has been developing a framework for a future self-assessment tool for nuclear operators and regulators. This paper will describe the effort to date, with particular emphasis on the steps the team took to align the framework with relevant IAEA self-assessment tools.

Development of a standard operating procedure for analysis of ammonia concentrations in coal fly ash.

DOT National Transportation Integrated Search

2015-04-01

Research was performed to support the development and recommendation of a standard operating : procedure (SOP) for analyzing the ammonia content in fly ash intended for use in concrete. A review : of existing ash producers found that several differen...

Development, test and evaluation of a computerized procedure for using Landsat data to estimate spring small grains acreage

NASA Technical Reports Server (NTRS)

Mohler, R. R. J.; Palmer, W. F.; Smyrski, M. M.; Baker, T. C.; Nazare, C. V.

1982-01-01

A number of methods which can provide information concerning crop acreages on the basis of a utilization of multispectral scanner (MSS) data require for their implementation a comparatively large amount of labor. The present investigation is concerned with a project designed to improve the efficiency of analysis through increased automation. The Caesar technique was developed to realize this objective. The processability rates of the Caesar procedure versus the historical state-of-the-art proportion estimation procedures were determined in an experiment. Attention is given to the study site, the aggregation technology, the results of the aggregation test, and questions of error characterization. It is found that the Caesar procedure, which has been developed for the spring small grains region of North America, is highly efficient and provides accurate results.

A Report on IAEA/RCA C7-RAS 6/061-004 Training Course in Chiba, Japan in 2014

PubMed Central

Kosuda, Shigeru; Saga, Tsuneo; Paez, Diana

2015-01-01

The C7-RAS 6/061-004 training course by the International Atomic Energy Agency/Regional Cooperative Agreement (IAEA/RCA) was held in Chiba in 2014. The syllabus, pre- and post-course evaluations, and survey questionnaire results were assembled in this course. The post-course evaluation, including 32 questions similar to the pre-course evaluation, was performed right after the end of the final educational lecture. The mean score showed an improvement, with the score rising from 57.0 points at the beginning to 66.5 points at the end. Among 22 trainees, the greatest score was in a higher range, with an improvement from 82 points at the beginning to 88 points at the end. The grading distribution, with regard to the training course, was as follows: excellent (68.2%), good (31.8%), average (0%), fair (0%), and poor (0%). This report on the training course, held in Chiba in 2014, will contribute to the future global plans of IAEA/RCA. Continuous training courses in member states are required to decrease the present disparities in the knowledge level, instrumentation, and human resources.

10 CFR 26.127 - Procedures.

Code of Federal Regulations, 2014 CFR

2014-01-01

..., implement, and maintain written standard operating procedures for each assay performed for drug and specimen... facility shall develop, implement, and maintain written standard operating procedures for each test. The...; (2) Preparation of reagents, standards, and controls; (3) Calibration procedures; (4) Derivation of...

10 CFR 26.127 - Procedures.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., implement, and maintain written standard operating procedures for each assay performed for drug and specimen... facility shall develop, implement, and maintain written standard operating procedures for each test. The...; (2) Preparation of reagents, standards, and controls; (3) Calibration procedures; (4) Derivation of...

10 CFR 26.127 - Procedures.

Code of Federal Regulations, 2013 CFR

2013-01-01

..., implement, and maintain written standard operating procedures for each assay performed for drug and specimen... facility shall develop, implement, and maintain written standard operating procedures for each test. The...; (2) Preparation of reagents, standards, and controls; (3) Calibration procedures; (4) Derivation of...

Development of NRC inspection procedure 38703: Commercial-grade dedication

DOE Office of Scientific and Technical Information (OSTI.GOV)

Potapovs, U.; Pettis, R.L. Jr.

1994-12-31

The purpose of this paper is to present an overview of the recently completed U.S. Nuclear Regulatory Commission (NRC) inspection procedure 38703, {open_quotes}Commercial Grade Dedication,{close_quotes} which was issued on November 8, 1993. This procedure embodies the information gained from the NRC`s inspections and assessments of licensee procurement practices, a public workshop, industry feedback and public comments, and the NRC`s perspective of the industry`s response to the Nuclear Management and Resource Council (NUMARC) procurement initiatives.

Experiences using IAEA Code of practice for radiation sterilization of tissue allografts: Validation and routine control

NASA Astrophysics Data System (ADS)

Hilmy, N.; Febrida, A.; Basril, A.

2007-11-01

Problems of tissue allografts in using International Standard (ISO) 11137 for validation of radiation sterilization dose (RSD) are limited and low numbers of uniform samples per production batch, those are products obtained from one donor. Allograft is a graft transplanted between two different individuals of the same species. The minimum number of uniform samples needed for verification dose (VD) experiment at the selected sterility assurance level (SAL) per production batch according to the IAEA Code is 20, i.e., 10 for bio-burden determination and the remaining 10 for sterilization test. Three methods of the IAEA Code have been used for validation of RSD, i.e., method A1 that is a modification of method 1 of ISO 11137:1995, method B (ISO 13409:1996), and method C (AAMI TIR 27:2001). This paper describes VD experiments using uniform products obtained from one cadaver donor, i.e., cancellous bones, demineralized bone powders and amnion grafts from one life donor. Results of the verification dose experiments show that RSD is 15.4 kGy for cancellous and demineralized bone grafts and 19.2 kGy for amnion grafts according to method A1 and 25 kGy according to methods B and C.

Developing the World's Digital Collection on Peaceful Uses of Atomic Energy.

ERIC Educational Resources Information Center

Levine, Emil

1997-01-01

Discusses the developers/development, maintainers, and users of the digital collection on peaceful uses of nuclear energy, produced by the International Nuclear Information System (INIS) of the International Atomic Energy Agency (IAEA). Sensitive to users in both developing and highly developed countries, this system provides closer linkage…

Development and validation of a screening procedure to identify speech-language delay in toddlers with cleft palate.

PubMed

Jørgensen, Line Dahl; Willadsen, Elisabeth

2017-01-01

The purpose of this study was to develop and validate a clinically useful speech-language screening procedure for young children with cleft palate ± cleft lip (CP) to identify those in need of speech-language intervention. Twenty-two children with CP were assigned to a +/- need for intervention conditions based on assessment of consonant inventory using a real-time listening procedure in combination with parent-reported expressive vocabulary. These measures allowed evaluation of early speech-language skills found to correlate significantly with later speech-language performance in longitudinal studies of children with CP. The external validity of this screening procedure was evaluated by comparing the +/- need for intervention assignment determined by the screening procedure to experienced speech-language pathologist (SLP)s' clinical judgement of whether or not a child needed early intervention. The results of real-time listening assessment showed good-excellent inter-rater agreement on different consonant inventory measures. Furthermore, there was almost perfect agreement between the children selected for intervention with the screening procedure and the clinical judgement of experienced SLPs indicate that the screening procedure is a valid way of identifying children with CP who need early intervention.

10 CFR 26.127 - Procedures.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 1 2011-01-01 2011-01-01 false Procedures. 26.127 Section 26.127 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Licensee Testing Facilities § 26.127 Procedures. (a) Licensee testing facilities shall develop, implement, and maintain clear and well-documented procedures for...

10 CFR 26.127 - Procedures.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Procedures. 26.127 Section 26.127 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Licensee Testing Facilities § 26.127 Procedures. (a) Licensee testing facilities shall develop, implement, and maintain clear and well-documented procedures for...

Perioperative considerations for neurosurgical procedures in the gravid patient: Continuing Professional Development.

PubMed

Chowdhury, Tumul; Chowdhury, Meenakshi; Schaller, Bernhard; Cappellani, Ronald B; Daya, Jayesh

2013-11-01

The complexity of neurosurgical procedures and their interactions with maternal and fetal physiologies are key factors in determining the overall maternal and fetal outcome. The literature and guidelines provide only partial information regarding the standard of care in these cases. The purpose of this Continuing Professional Development module is to review the issues related to common neurosurgical conditions and their optimal anesthetic management. The most common neurosurgical conditions found in pregnancy include brain tumours, cerebrovascular diseases, spinal pathologies, and neurotrauma. Though rare, these conditions and related procedures may affect maternal and fetal outcome. Maternal considerations should be given priority in cases of emergent surgeries irrespective of trimester. In the early first trimester, risk of fetal loss and congenital malformation are substantial; hence, proper counselling should be given to the mother with special emphasis on therapeutic abortion. When indicated, anticonvulsants should be started as early as possible and continued throughout pregnancy. Surgical procedures can be performed with relative safety during the second trimester and early third trimester. After 34 weeks, delivery seems to be the first choice, and the role of regional anesthesia in this situation should be carefully planned after proper review of neurosurgical pathology and maternal condition. During acute neurological deterioration, however, Cesarean delivery under general anesthesia should be anticipated. A multidisciplinary approach with good communication amongst all team members certainly plays a crucial role for successful management of such cases.

Systems development and difficulties in implementing procedures for elder abuse prevention among private community general support centers in Japan.

PubMed

Nakanishi, Miharu; Nakashima, Taeko; Yamaoka, Yukako; Hada, Keiko; Tanaka, Hideaki

2014-01-01

The present study examines differences in systems development and difficulties in implementing procedures for elder abuse prevention in 1,119 private and 606 public community general support centers under the public long-term care insurance program in Japan. The private community general support centers showed more difficulty implementing procedures than the public community general support centers. Controlling for the type of municipality, progress in systems development did not differ between the private and public community general support centers. Further research should examine how the characteristics of municipal governments are related to systems development in community general support centers.

Designing Flightdeck Procedures: Literature Resources

NASA Technical Reports Server (NTRS)

Feldman, Jolene; Barshi, Immanuel; Degani, Asaf; Loukopoulou, Loukia; Mauro, Robert

2017-01-01

This technical publication contains the titles, abstracts, summaries, descriptions, and/or annotations of available literature sources on procedure design and development, requirements, and guidance. It is designed to provide users with an easy access to available resources on the topic of procedure design, and with a sense of the contents of these sources. This repository of information is organized into the following publication sources: Research (e.g., journal articles, conference proceedings), Manufacturers' (e.g., operation manuals, newsletters), and Regulatory and/or Government (e.g., advisory circulars, reports). An additional section contains synopses of Accident/Incident Reports involving procedures. This work directly supports a comprehensive memorandum by Barshi, Mauro, Degani, & Loukopoulou (2016) that summarizes the results of a multi-year project, partially funded by the FAA, to develop technical reference materials that support guidance on the process of developing cockpit procedures (see "Designing Flightdeck Procedures" https://ntrs.nasa.gov/archive/nasa/casi.ntrs.nasa.gov/20160013263.pdf). An extensive treatment of this topic is presented in a forthcoming book by the same authors.

The impact of the International Atomic Energy Agency (IAEA) program on radiation and tissue banking in Uruguay: development of tissues quality control and quality management system in the National Multi-Tissue Bank of Uruguay.

PubMed

Alvarez, I; Morales Pedraza, Jorge; Saldías, M C; Pérez Campos, H; Wodowóz, O; Acosta, María; Vicentino, W; Silva, W; Rodríguez, G; Machín, D; Alvarez, O

2009-05-01

BNOT was created and regulated in 1977 and started its operation in 1978 according to the Decree No. 86/1977. By the Decree 248/005 is transformed in the National Institute of Donation and Transplantation of Cells, Tissues and Organs (Instituto Nacional de Donación y Trasplante de Células, Tejidos y Organos--INDT). The organisation has been operating within the State University Medical School and the Public Health Secretary and it is the governmental organisation responsible for the regulation, policy and management of donation and transplantation in Uruguay. By the Decree 160/2006 is responsible for human cells and tissues regulation too. The participation of the INDT in the IAEA program facilitated the introduction of the radiation sterilisation technique for the first time in the country. The radiation sterilisation of tissues processed by INDT (ex BNOT), was initially carried out in the 60 Cobalt Industrial Plant in the National Atomic Energy Commission of Argentina and now is carried out in INDT, using a Gamma Cell 220 Excel, which was provided by the IAEA through the national project URU/7/005. The results of the implementation of tissues, quality control and quality management system, are showed.

Developing Tsunami Evacuation Plans, Maps, And Procedures: Pilot Project in Central America

NASA Astrophysics Data System (ADS)

Arcos, N. P.; Kong, L. S. L.; Arcas, D.; Aliaga, B.; Coetzee, D.; Leonard, J.

2015-12-01

In the End-to-End tsunami warning chain, once a forecast is provided and a warning alert issued, communities must know what to do and where to go. The 'where to' answer would be reliable and practical community-level tsunami evacuation maps. Following the Exercise Pacific Wave 2011, a questionnaire was sent to the 46 Member States of Pacific Tsunami Warning System (PTWS). The results revealed over 42 percent of Member States lacked tsunami mass coastal evacuation plans. Additionally, a significant gap in mapping was exposed as over 55 percent of Member States lacked tsunami evacuation maps, routes, signs and assembly points. Thereby, a significant portion of countries in the Pacific lack appropriate tsunami planning and mapping for their at-risk coastal communities. While a variety of tools exist to establish tsunami inundation areas, these are inconsistent while a methodology has not been developed to assist countries develop tsunami evacuation maps, plans, and procedures. The International Tsunami Information Center (ITIC) and partners is leading a Pilot Project in Honduras demonstrating that globally standardized tools and methodologies can be applied by a country, with minimal tsunami warning and mitigation resources, towards the determination of tsunami inundation areas and subsequently community-owned tsunami evacuation maps and plans for at-risk communities. The Pilot involves a 1- to 2-year long process centered on a series of linked tsunami training workshops on: evacuation planning, evacuation map development, inundation modeling and map creation, tsunami warning & emergency response Standard Operating Procedures (SOPs), and conducting tsunami exercises (including evacuation). The Pilot's completion is capped with a UNESCO/IOC document so that other countries can replicate the process in their tsunami-prone communities.

10 CFR 26.157 - Procedures.

Code of Federal Regulations, 2010 CFR

2010-01-01

... of standard operating procedures for each assay performed for licensees and other entities for drug... 10 Energy 1 2010-01-01 2010-01-01 false Procedures. 26.157 Section 26.157 Energy NUCLEAR... Services § 26.157 Procedures. (a) HHS-certified laboratories shall develop, implement, and maintain clear...

10 CFR 26.157 - Procedures.

Code of Federal Regulations, 2013 CFR

2013-01-01

... of standard operating procedures for each assay performed for licensees and other entities for drug... 10 Energy 1 2013-01-01 2013-01-01 false Procedures. 26.157 Section 26.157 Energy NUCLEAR... Services § 26.157 Procedures. (a) HHS-certified laboratories shall develop, implement, and maintain clear...

10 CFR 26.157 - Procedures.

Code of Federal Regulations, 2011 CFR

2011-01-01

... of standard operating procedures for each assay performed for licensees and other entities for drug... 10 Energy 1 2011-01-01 2011-01-01 false Procedures. 26.157 Section 26.157 Energy NUCLEAR... Services § 26.157 Procedures. (a) HHS-certified laboratories shall develop, implement, and maintain clear...

10 CFR 26.157 - Procedures.

Code of Federal Regulations, 2014 CFR

2014-01-01

... of standard operating procedures for each assay performed for licensees and other entities for drug... 10 Energy 1 2014-01-01 2014-01-01 false Procedures. 26.157 Section 26.157 Energy NUCLEAR... Services § 26.157 Procedures. (a) HHS-certified laboratories shall develop, implement, and maintain clear...

10 CFR 26.157 - Procedures.

Code of Federal Regulations, 2012 CFR

2012-01-01

... of standard operating procedures for each assay performed for licensees and other entities for drug... 10 Energy 1 2012-01-01 2012-01-01 false Procedures. 26.157 Section 26.157 Energy NUCLEAR... Services § 26.157 Procedures. (a) HHS-certified laboratories shall develop, implement, and maintain clear...

Phase 2 environmental site investigation procedures and technologies for property transfer and PS and E development

DOT National Transportation Integrated Search

1999-05-01

The purpose of this project is to provide TxDOT with an improved procedure for conducting environmental site investigations at various stages during transportation infrastructure development. The project seeks to identify modern assessment technologi...

Arrest procedures for driving while intoxicated

DOT National Transportation Integrated Search

1980-08-01

Model arrest procedures were developed to enhance the enforcement of laws against driving while intoxicated (DWI). Development was based on answers obtained to the following questions: what procedural alternatives are now possible; how do alternative...

MO-DE-204-01: Radiation Doses in Over 50 Developing Countries of Asia, Africa, Eastern European and Latin America

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rehani, M.

2016-06-15

The main topic of the session is to show how dose optimization is being implemented in various regions of the world, including Europe, Australia, North America and other regions. A multi-national study conducted under International Atomic Energy Agency (IAEA) across more than 50 less resourced countries gave insight into patient radiation doses and safety practices in CT, mammography, radiography and interventional procedures, both for children and adults. An important outcome was the capability development on dose assessment and management. An overview of recent European projects related to CT radiation dose and optimization both to adults and children will be presented.more » Existing data on DRLs together with a European methodology proposed on establishing and using DRLs for paediatric radiodiagnostic imaging and interventional radiology practices will be shown. Compared with much of Europe at least, many Australian imaging practices are relatively new to the task of diagnostic imaging dose optimisation. In 2008 the Australian Government prescribed a requirement to periodically compare patient radiation doses with diagnostic reference levels (DRLs), where DRLs have been established. Until recently, Australia had only established DRLs for computed tomography (CT). Regardless, both professional society and individual efforts to improved data collection and develop optimisation strategies across a range of modalities continues. Progress in this field, principally with respect to CT and interventional fluoroscopy will be presented. In the US, dose reduction and optimization efforts for computed tomography have been promoted and mandated by several organizations and accrediting entities. This presentation will cover the general motivation, implementation, and implications of such efforts. Learning Objectives: Understand importance of the dose optimization in Diagnostic Radiology. See how this goal is achieved in different regions of the World. Learn about the

Fuel Cycle Analysis Framework Base Cases for the IAEA/INPRO GAINS Collaborative Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brent Dixon

Thirteen countries participated in the Collaborative Project GAINS “Global Architecture of Innovative Nuclear Energy Systems Based on Thermal and Fast Reactors Including a Closed Fuel Cycle”, which was the primary activity within the IAEA/INPRO Program Area B: “Global Vision on Sustainable Nuclear Energy” for the last three years. The overall objective of GAINS was to develop a standard framework for assessing future nuclear energy systems taking into account sustainable development, and to validate results through sample analyses. This paper details the eight scenarios that constitute the GAINS framework base cases for analysis of the transition to future innovative nuclear energymore » systems. The framework base cases provide a reference for users of the framework to start from in developing and assessing their own alternate systems. Each base case is described along with performance results against the GAINS sustainability evaluation metrics. The eight cases include four using a moderate growth projection and four using a high growth projection for global nuclear electricity generation through 2100. The cases are divided into two sets, addressing homogeneous and heterogeneous scenarios developed by GAINS to model global fuel cycle strategies. The heterogeneous world scenario considers three separate nuclear groups based on their fuel cycle strategies, with non-synergistic and synergistic cases. The framework base case analyses results show the impact of these different fuel cycle strategies while providing references for future users of the GAINS framework. A large number of scenario alterations are possible and can be used to assess different strategies, different technologies, and different assumptions about possible futures of nuclear power. Results can be compared to the framework base cases to assess where these alternate cases perform differently versus the sustainability indicators.« less

Development of characterization protocol for mixed liquid radioactive waste classification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zakaria, Norasalwa, E-mail: norasalwa@nuclearmalaysia.gov.my; Wafa, Syed Asraf; Wo, Yii Mei

2015-04-29

Mixed liquid organic waste generated from health-care and research activities containing tritium, carbon-14, and other radionuclides posed specific challenges in its management. Often, these wastes become legacy waste in many nuclear facilities and being considered as ‘problematic’ waste. One of the most important recommendations made by IAEA is to perform multistage processes aiming at declassification of the waste. At this moment, approximately 3000 bottles of mixed liquid waste, with estimated volume of 6000 litres are currently stored at the National Radioactive Waste Management Centre, Malaysia and some have been stored for more than 25 years. The aim of this studymore » is to develop a characterization protocol towards reclassification of these wastes. The characterization protocol entails waste identification, waste screening and segregation, and analytical radionuclides profiling using various analytical procedures including gross alpha/ gross beta, gamma spectrometry, and LSC method. The results obtained from the characterization protocol are used to establish criteria for speedy classification of the waste.« less

Acoustic radiation force impulse imaging for real-time observation of lesion development during radiofrequency ablation procedures

NASA Astrophysics Data System (ADS)

Fahey, Brian J.; Trahey, Gregg E.

2005-04-01

When performing radiofrequency ablation (RFA) procedures, physicians currently have little or no feedback concerning the success of the treatment until follow-up assessments are made days to weeks later. To be successful, RFA must induce a thermal lesion of sufficient volume to completely destroy a target tumor or completely isolate an aberrant cardiac pathway. Although ultrasound, computed tomography (CT), and CT-based fluoroscopy have found use in guiding RFA treatments, they are deficient in giving accurate assessments of lesion size or boundaries during procedures. As induced thermal lesion size can vary considerably from patient to patient, the current lack of real-time feedback during RFA procedures is troublesome. We have developed a technique for real-time monitoring of thermal lesion size during RFA procedures utilizing acoustic radiation force impulse (ARFI) imaging. In both ex vivo and in vivo tissues, ARFI imaging provided better thermal lesion contrast and better overall appreciation for lesion size and boundaries relative to conventional sonography. The thermal safety of ARFI imaging for use at clinically realistic depths was also verified through the use of finite element method models. As ARFI imaging is implemented entirely on a diagnostic ultrasound scanner, it is a convenient, inexpensive, and promising modality for monitoring RFA procedures in vivo.

Market Research Survey of Commercial Off-The-Shelf (COTS) Portable MS Systems for IAEA Safeguards Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hart, Garret L.; Hager, George J.; Barinaga, Charles J.

2013-02-01

This report summarizes the results for the market research survey of mass spectrometers that are deemed pertinent to International Atomic Energy Agency (IAEA) needs and strategic objectives. The focus of the report is on MS instruments that represent currently available (or soon to be) commercial off-the shelf (COTS) technology and weigh less than 400 pounds. A compilation of all available MS instruments (36 COTS and 2 R&D) is presented, along with pertinent information regarding each instrument.

Developing Physiologic Models for Emergency Medical Procedures Under Microgravity

NASA Technical Reports Server (NTRS)

Parker, Nigel; O'Quinn, Veronica

2012-01-01

Several technological enhancements have been made to METI's commercial Emergency Care Simulator (ECS) with regard to how microgravity affects human physiology. The ECS uses both a software-only lung simulation, and an integrated mannequin lung that uses a physical lung bag for creating chest excursions, and a digital simulation of lung mechanics and gas exchange. METI s patient simulators incorporate models of human physiology that simulate lung and chest wall mechanics, as well as pulmonary gas exchange. Microgravity affects how O2 and CO2 are exchanged in the lungs. Procedures were also developed to take into affect the Glasgow Coma Scale for determining levels of consciousness by varying the ECS eye-blinking function to partially indicate the level of consciousness of the patient. In addition, the ECS was modified to provide various levels of pulses from weak and thready to hyper-dynamic to assist in assessing patient conditions from the femoral, carotid, brachial, and pedal pulse locations.

Developing Physiologic Models for Emergency Medical Procedures Under Microgravity

NASA Technical Reports Server (NTRS)

Parker, Nigel; OQuinn, Veronica

2012-01-01

Several technological enhancements have been made to METI's commercial Emergency Care Simulator (ECS) with regard to how microgravity affects human physiology. The ECS uses both a software-only lung simulation, and an integrated mannequin lung that uses a physical lung bag for creating chest excursions, and a digital simulation of lung mechanics and gas exchange. METI's patient simulators incorporate models of human physiology that simulate lung and chest wall mechanics, as well as pulmonary gas exchange. Microgravity affects how O2 and CO2 are exchanged in the lungs. Procedures were also developed to take into affect the Glasgow Coma Scale for determining levels of consciousness by varying the ECS eye-blinking function to partially indicate the level of consciousness of the patient. In addition, the ECS was modified to provide various levels of pulses from weak and thready to hyper-dynamic to assist in assessing patient conditions from the femoral, carotid, brachial, and pedal pulse locations.

Development of a standard operating procedure for the collection of pyrethroids in water and sediment matrices

EPA Science Inventory

Through a Regional Applied Research Effort grant to the United States Geological Survey, Region 9 collaborated with ORD on this project to develop a standard operating procedure for collection of water and sediment samples for pyrethroid analysis.

Operational Control Procedures for the Activated Sludge Process, Part III-A: Calculation Procedures.

ERIC Educational Resources Information Center

West, Alfred W.

This is the second in a series of documents developed by the National Training and Operational Technology Center describing operational control procedures for the activated sludge process used in wastewater treatment. This document deals exclusively with the calculation procedures, including simplified mixing formulas, aeration tank…

Development of a digital impression procedure using photogrammetry for complete denture fabrication.

PubMed

Matsuda, Takashi; Goto, Takaharu; Kurahashi, Kosuke; Kashiwabara, Toshiya; Ichikawa, Tetsuo

We developed an innovative procedure for digitizing maxillary edentulous residual ridges with a photogrammetric system capable of estimating three-dimensional (3D) digital forms from multiple two-dimensional (2D) digital images. The aim of this study was to validate the effectiveness of the photogrammetric system. Impressions of the maxillary residual ridges of five edentulous patients were taken with four kinds of procedures: three conventional impression procedures and the photogrammetric system. Plaster models were fabricated from conventional impressions and digitized with a 3D scanner. Two 3D forms out of four forms were superimposed with 3D inspection software, and differences were evaluated using a least squares best fit algorithm. The in vitro experiment suggested that better imaging conditions were in the horizontal range of ± 15 degrees and at a vertical angle of 45 degrees. The mean difference between the photogrammetric image (Form A) and the image taken from conventional preliminarily impression (Form C) was 0.52 ± 0.22 mm. The mean difference between the image taken of final impression through a special tray (Form B) and Form C was 0.26 ± 0.06 mm. The mean difference between the image taken from conventional final impression (Form D) and Form C was 0.25 ± 0.07 mm. The difference between Forms A and C was significantly larger than the differences between Forms B and C and between Forms D and C. The results of this study suggest that obtaining digital impressions of edentulous residual ridges using a photogrammetric system is feasible and available for clinical use.

24 CFR 291.210 - Direct sales procedures.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Direct sales procedures. 291.210... URBAN DEVELOPMENT HUD-OWNED PROPERTIES DISPOSITION OF HUD-ACQUIRED SINGLE FAMILY PROPERTY Sales Procedures § 291.210 Direct sales procedures. When HUD conducts the sales listed in § 291.90(c), it will sell...

24 CFR 291.210 - Direct sales procedures.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 2 2011-04-01 2011-04-01 false Direct sales procedures. 291.210... URBAN DEVELOPMENT HUD-OWNED PROPERTIES DISPOSITION OF HUD-ACQUIRED SINGLE FAMILY PROPERTY Sales Procedures § 291.210 Direct sales procedures. When HUD conducts the sales listed in § 291.90(c), it will sell...

24 CFR 291.210 - Direct sales procedures.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 24 Housing and Urban Development 2 2014-04-01 2014-04-01 false Direct sales procedures. 291.210... URBAN DEVELOPMENT HUD-OWNED PROPERTIES DISPOSITION OF HUD-ACQUIRED SINGLE FAMILY PROPERTY Sales Procedures § 291.210 Direct sales procedures. When HUD conducts the sales listed in § 291.90(c), it will sell...

Powertrain Test Procedure Development for EPA GHG Certification of Medium- and Heavy-Duty Engines and Vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chambon, Paul H.; Deter, Dean D.

2016-07-01

xiii ABSTRACT The goal of this project is to develop and evaluate powertrain test procedures that can accurately simulate real-world operating conditions, and to determine greenhouse gas (GHG) emissions of advanced medium- and heavy-duty engine and vehicle technologies. ORNL used their Vehicle System Integration Laboratory to evaluate test procedures on a stand-alone engine as well as two powertrains. Those components where subjected to various drive cycles and vehicle conditions to evaluate the validity of the results over a broad range of test conditions. Overall, more than 1000 tests were performed. The data are compiled and analyzed in this report.

Development of a personal computer-based secondary task procedure as a surrogate for a driving simulator

DOT National Transportation Integrated Search

2007-08-01

This research was conducted to develop and test a personal computer-based study procedure (PCSP) with secondary task loading for use in human factors laboratory experiments in lieu of a driving simulator to test reading time and understanding of traf...

Development of Career Motivational Prediction and Selection Procedures.

ERIC Educational Resources Information Center

Culclasure, David F.

The report constitutes a comprehensive review of the literature related to career motivation and selection procedures. It surveyed the reported techniques for measuring career motivation and interest which were used by 24 industrial firms, 14 personnel and management consulting organizations, 8 marketing research firms, and various governmental…

SUPPORTING THE INDUSTRY BY DEVELOPING A DESIGN GUIDANCE FOR COMPUTER-BASED PROCEDURES FOR FIELD WORKERS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oxstrand, Johanna; LeBlanc, Katya

The paper-based procedures currently used for nearly all activities in the commercial nuclear power industry have a long history of ensuring safe operation of the plants. However, there is potential to greatly increase efficiency and safety by improving how the human interacts with the procedures, which can be achieved through the use of computer-based procedures (CBPs). A CBP system offers a vast variety of improvements, such as context driven job aids, integrated human performance tools and dynamic step presentation. As a step toward the goal of improving procedure use performance, the U.S. Department of Energy Light Water Reactor Sustainability Programmore » researchers, together with the nuclear industry, have been investigating the possibility and feasibility of replacing current paper-based procedures with CBPs. The main purpose of the CBP research conducted at the Idaho National Laboratory was to provide design guidance to the nuclear industry to be used by both utilities and vendors. After studying existing design guidance for CBP systems, the researchers concluded that the majority of the existing guidance is intended for control room CBP systems, and does not necessarily address the challenges of designing CBP systems for instructions carried out in the field. Further, the guidance is often presented on a high level, which leaves the designer to interpret what is meant by the guidance and how to specifically implement it. The authors developed a design guidance to provide guidance specifically tailored to instructions that are carried out in the field based.« less

IAEA Co-ordinated Research Project: update of X-ray and gamma-ray decay data standards for detector calibration and other applications.

PubMed

Nichols, Alan L

2004-01-01

A Co-ordinated Research Project (CRP) was established in 1998 by the IAEA Nuclear Data Section (Update of X-ray and gamma-ray Decay Data Standards for Detector Calibration and Other Applications), in order to improve further the recommended decay data used to undertake efficiency calibrations of gamma-ray detectors. Participants in this CRP reviewed and modified the list of radionuclides most suited for detector efficiency calibration, and also considered the decay-data needs for safeguards, waste management, dosimetry, nuclear medicine, material analysis and environmental monitoring. Overall, 62 radionuclides were selected for decay-data evaluation, along with four parent-daughter combinations and two natural decay chains. gamma-ray emissions from specific nuclear reactions were also included to extend the calibrant energy well beyond 10 MeV. A significant number of these decay-data evaluations have been completed, and an IAEA-TECDOC report and database are in the process of being assembled for planned completion by the end of 2003.

Development of an improved overlay design procedure for Oregon : vol. I, interim report, background and framework.

DOT National Transportation Integrated Search

1986-12-01

This report is the first in a three-volume series dealing with the development of an improved overlay design procedure for Oregon. This report presents the results of the first-year findings and includes: (1) a detailed review of the literature; (2) ...

10 CFR 835.104 - Written procedures.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 4 2012-01-01 2012-01-01 false Written procedures. 835.104 Section 835.104 Energy DEPARTMENT OF ENERGY OCCUPATIONAL RADIATION PROTECTION Management and Administrative Requirements § 835.104 Written procedures. Written procedures shall be developed and implemented as necessary to ensure...

10 CFR 835.104 - Written procedures.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Written procedures. 835.104 Section 835.104 Energy DEPARTMENT OF ENERGY OCCUPATIONAL RADIATION PROTECTION Management and Administrative Requirements § 835.104 Written procedures. Written procedures shall be developed and implemented as necessary to ensure...

10 CFR 835.104 - Written procedures.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 4 2011-01-01 2011-01-01 false Written procedures. 835.104 Section 835.104 Energy DEPARTMENT OF ENERGY OCCUPATIONAL RADIATION PROTECTION Management and Administrative Requirements § 835.104 Written procedures. Written procedures shall be developed and implemented as necessary to ensure...

10 CFR 835.104 - Written procedures.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 4 2013-01-01 2013-01-01 false Written procedures. 835.104 Section 835.104 Energy DEPARTMENT OF ENERGY OCCUPATIONAL RADIATION PROTECTION Management and Administrative Requirements § 835.104 Written procedures. Written procedures shall be developed and implemented as necessary to ensure...

10 CFR 835.104 - Written procedures.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 4 2014-01-01 2014-01-01 false Written procedures. 835.104 Section 835.104 Energy DEPARTMENT OF ENERGY OCCUPATIONAL RADIATION PROTECTION Management and Administrative Requirements § 835.104 Written procedures. Written procedures shall be developed and implemented as necessary to ensure...

Development of a toxicity identification evaluation procedure for characterizing metal toxicity in marine sediments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burgess, R.M.; Cantwell, M.G.; Pelletier, M.C.

2000-04-01

A multiagency effort is underway to develop whole sediment toxicity identification evaluation (TIE) methods. Whole sediment TIE methods will be critical tools for characterizing toxicity at hazardous waste sites and in the conduct of environmental risk assessments. The research approach is based on the predominance of three classes of toxicants in sediments: ammonia, nonpolar organic chemicals, and metals. Here the authors describe a procedure for characterizing acute toxicity caused by metals in whole marine sediments. The procedure involves adding a chelating resin to sediments, resulting in the sequestration of bioavailable metal while not stressing testing organisms. Within the testing chambers,more » the presence of resin resulted in statistically significant reductions in the overlying and interstitial water concentrations of five metals (cadmium, copper, nickel, lead, and zinc) generally by factors of 40 and 200. Toxicity to both the amphipod Ampelisca abdita and mysid Americamysis bahia (formerly Mysidopsis bahia) of sediments spiked with the five metals was decreased by approximately a factor of four when resin was present. While very effective at reducing the concentrations and toxicity of metals, the resin has only minor ameliorative effects on the toxicity of ammonia and a representative nonpolar toxicant (Endosulfan). Resin and accumulated metal were easily isolated from the testing system following exposures allowing for the initiation of phase II TIE (identification) procedures. This procedure using the addition of a chelating resin provides an approach for determining the importance of metals to the toxicity of marine sediments. Work is continuing to validate the method with environmentally contaminated sediments.« less

Sequential extraction procedure for determination of uranium, thorium, radium, lead and polonium radionuclides by alpha spectrometry in environmental samples

NASA Astrophysics Data System (ADS)

Oliveira, J. M.; Carvalho, F. P.

2006-01-01

A sequential extraction technique was developed and tested for common naturally-occurring radionuclides. This technique allows the extraction and purification of uranium, thorium, radium, lead, and polonium radionuclides from the same sample. Environmental materials such as water, soil, and biological samples can be analyzed for those radionuclides without matrix interferences in the quality of radioelement purification and in the radiochemical yield. The use of isotopic tracers (232U, 229Th, 224Ra, 209Po, and stable lead carrier) added to the sample in the beginning of the chemical procedure, enables an accurate control of the radiochemical yield for each radioelement. The ion extraction procedure, applied after either complete dissolution of the solid sample with mineral acids or co-precipitation of dissolved radionuclide with MnO2 for aqueous samples, includes the use of commercially available pre-packed columns from Eichrom® and ion exchange columns packed with Bio-Rad resins, in altogether three chromatography columns. All radioactive elements but one are purified and electroplated on stainless steel discs. Polonium is spontaneously plated on a silver disc. The discs are measured using high resolution silicon surface barrier detectors. 210Pb, a beta emitter, can be measured either through the beta emission of 210Bi, or stored for a few months and determined by alpha spectrometry through the in-growth of 210Po. This sequential extraction chromatography technique was tested and validated with the analysis of certified reference materials from the IAEA. Reproducibility was tested through repeated analysis of the same homogeneous material (water sample).

Large Area Crop Inventory Experiment (LACIE). Development of procedure M for multicrop inventory, with tests of a spring-wheat configuration

NASA Technical Reports Server (NTRS)

Horvath, R. (Principal Investigator); Cicone, R.; Crist, E.; Kauth, R. J.; Lambeck, P.; Malila, W. A.; Richardson, W.

1979-01-01

The author has identified the following significant results. An outgrowth of research and development activities in support of LACIE was a multicrop area estimation procedure, Procedure M. This procedure was a flexible, modular system that could be operated within the LACIE framework. Its distinctive features were refined preprocessing (including spatially varying correction for atmospheric haze), definition of field like spatial features for labeling, spectral stratification, and unbiased selection of samples to label and crop area estimation without conventional maximum likelihood classification.

Development of a Course of Study in FDA Drug Regulatory Procedures

ERIC Educational Resources Information Center

Jacobs, Robin Wills; King, James C.

1977-01-01

It is evident that more colleges of pharmacy should establish some major course of study in the area of governmental drug regulatory procedures. This study is aimed at expanding cooperative educational programs through an FDA residency for pharmacy students and preparing a didactic course in FDA procedures. (LBH)

19 CFR 122.173 - Application procedures.

Code of Federal Regulations, 2014 CFR

2014-04-01

... that it has developed and will continue to maintain standard operating procedures (SOP) which are... 19 Customs Duties 1 2014-04-01 2014-04-01 false Application procedures. 122.173 Section 122.173... TREASURY AIR COMMERCE REGULATIONS Air Carrier Smuggling Prevention Program § 122.173 Application procedures...

19 CFR 122.173 - Application procedures.

Code of Federal Regulations, 2011 CFR

2011-04-01

... that it has developed and will continue to maintain standard operating procedures (SOP) which are... 19 Customs Duties 1 2011-04-01 2011-04-01 false Application procedures. 122.173 Section 122.173... TREASURY AIR COMMERCE REGULATIONS Air Carrier Smuggling Prevention Program § 122.173 Application procedures...

19 CFR 122.173 - Application procedures.

Code of Federal Regulations, 2010 CFR

2010-04-01

... that it has developed and will continue to maintain standard operating procedures (SOP) which are... 19 Customs Duties 1 2010-04-01 2010-04-01 false Application procedures. 122.173 Section 122.173... TREASURY AIR COMMERCE REGULATIONS Air Carrier Smuggling Prevention Program § 122.173 Application procedures...

19 CFR 122.173 - Application procedures.

Code of Federal Regulations, 2012 CFR

2012-04-01

... that it has developed and will continue to maintain standard operating procedures (SOP) which are... 19 Customs Duties 1 2012-04-01 2012-04-01 false Application procedures. 122.173 Section 122.173... TREASURY AIR COMMERCE REGULATIONS Air Carrier Smuggling Prevention Program § 122.173 Application procedures...

19 CFR 122.173 - Application procedures.

Code of Federal Regulations, 2013 CFR

2013-04-01

... that it has developed and will continue to maintain standard operating procedures (SOP) which are... 19 Customs Duties 1 2013-04-01 2013-04-01 false Application procedures. 122.173 Section 122.173... TREASURY AIR COMMERCE REGULATIONS Air Carrier Smuggling Prevention Program § 122.173 Application procedures...

Efficiency of three diets for larval development in mass rearing Aedes albopictus (Diptera: Culicidae).

PubMed

Puggioli, Arianna; Balestrino, F; Damiens, D; Lees, R S; Soliban, S M; Madakacherry, O; Dindo, M L; Bellini, R; Gilles, J R L

2013-07-01

A fundamental step in establishing a mass production system is the development of a larval diet that promotes high adult performance at a reasonable cost. To identify a suitable larval diet for Aedes albopictus (Skuse), three diets were compared: a standard laboratory diet used at the Centro Agricoltura Ambiente, Italy (CAA) and two diets developed specifically for mosquito mass rearing at the FAO/IAEA Laboratory, Austria. The two IAEA diets, without affecting survival to the pupal stage, resulted in a shorter time to pupation and to emergence when compared with the CAA diet. At 24 h from pupation onset, 50 and 90% of the male pupae produced on the CAA and IAEA diets, respectively, had formed and could be collected. The diet received during the larval stage affected the longevity of adult males with access to water only, with best results observed when using the CAA larval diet. However, similar longevity among diet treatments was observed when males were supplied with sucrose solution. No differences were observed in the effects of larval diet on adult male size or female fecundity and fertility. Considering these results, along with the relative costs of the three diets, the IAEA 2 diet is found to be the preferred choice for mass rearing of Aedes albopictus, particularly if a sugar meal can be given to adult males before release, to ensure their teneral reserves are sufficient for survival, dispersal, and mating in the field.

Analytical procedure validation and the quality by design paradigm.

PubMed

Rozet, Eric; Lebrun, Pierre; Michiels, Jean-François; Sondag, Perceval; Scherder, Tara; Boulanger, Bruno

2015-01-01

Since the adoption of the ICH Q8 document concerning the development of pharmaceutical processes following a quality by design (QbD) approach, there have been many discussions on the opportunity for analytical procedure developments to follow a similar approach. While development and optimization of analytical procedure following QbD principles have been largely discussed and described, the place of analytical procedure validation in this framework has not been clarified. This article aims at showing that analytical procedure validation is fully integrated into the QbD paradigm and is an essential step in developing analytical procedures that are effectively fit for purpose. Adequate statistical methodologies have also their role to play: such as design of experiments, statistical modeling, and probabilistic statements. The outcome of analytical procedure validation is also an analytical procedure design space, and from it, control strategy can be set.

Precision Information Environment (PIE) for International Safeguards: Pre-Demonstration Development Use Cases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gastelum, Zoe N.; Henry, Michael J.

2013-11-13

In FY2013, the PIE International Safeguards team demonstrated our development progress to U.S. Department of Energy (DOE) staff from the Office of Nonproliferation and International Security (NA-24, our client) and the Office of Defense Nuclear Nonproliferation Research and Development (NA-22). Following the demonstration, the team was asked by our client to complete additional development prior to a planned demonstration at the International Atomic Energy Agency (IAEA), scheduled tentatively for January or spring of 2014. The team discussed four potential areas for development (in priority order), and will develop them as time and funding permit prior to an IAEA demonstration. Themore » four capability areas are: 1. Addition of equipment manuals to PIE-accessible files 2. Optical character recognition (OCR) of photographed text 3. Barcode reader with information look-up from a database 4. Add Facilities to Data Model 5. Geospatial capabilities with information integration Each area will be described below in a use case.« less

Clustering algorithm evaluation and the development of a replacement for procedure 1. [for crop inventories

NASA Technical Reports Server (NTRS)

Lennington, R. K.; Johnson, J. K.

1979-01-01

An efficient procedure which clusters data using a completely unsupervised clustering algorithm and then uses labeled pixels to label the resulting clusters or perform a stratified estimate using the clusters as strata is developed. Three clustering algorithms, CLASSY, AMOEBA, and ISOCLS, are compared for efficiency. Three stratified estimation schemes and three labeling schemes are also considered and compared.

Physicists without borders

NASA Astrophysics Data System (ADS)

Jeandron, Michelle

2008-06-01

The International Atomic Energy Agency (IAEA), which has its headquarters in Vienna, Austria, is a specialized agency of the United Nations (UN) that seeks to promote the safe, secure and peaceful use of nuclear technology. It has three main areas of expertise. It is the world's nuclear inspectorate, sending inspectors to more than 140 UN member states, from Brazil to Japan, to verify that nuclear technology is not being used for military purposes. The IAEA also helps countries to improve their nuclear safety procedures and to prepare for emergencies. Finally, it serves as a focal point for the world's development of nuclear science and technology across all fields.

48 CFR 742.1503 - Procedures.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Procedures. 742.1503 Section 742.1503 Federal Acquisition Regulations System AGENCY FOR INTERNATIONAL DEVELOPMENT CONTRACT MANAGEMENT CONTRACT ADMINISTRATION Contractor Performance Information 742.1503 Procedures. (a) [Reserved] (b...

48 CFR 742.1503 - Procedures.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 5 2011-10-01 2011-10-01 false Procedures. 742.1503 Section 742.1503 Federal Acquisition Regulations System AGENCY FOR INTERNATIONAL DEVELOPMENT CONTRACT MANAGEMENT CONTRACT ADMINISTRATION Contractor Performance Information 742.1503 Procedures. (a) [Reserved] (b...

Relations among conceptual knowledge, procedural knowledge, and procedural flexibility in two samples differing in prior knowledge.

PubMed

Schneider, Michael; Rittle-Johnson, Bethany; Star, Jon R

2011-11-01

Competence in many domains rests on children developing conceptual and procedural knowledge, as well as procedural flexibility. However, research on the developmental relations between these different types of knowledge has yielded unclear results, in part because little attention has been paid to the validity of the measures or to the effects of prior knowledge on the relations. To overcome these problems, we modeled the three constructs in the domain of equation solving as latent factors and tested (a) whether the predictive relations between conceptual and procedural knowledge were bidirectional, (b) whether these interrelations were moderated by prior knowledge, and (c) how both constructs contributed to procedural flexibility. We analyzed data from 2 measurement points each from two samples (Ns = 228 and 304) of middle school students who differed in prior knowledge. Conceptual and procedural knowledge had stable bidirectional relations that were not moderated by prior knowledge. Both kinds of knowledge contributed independently to procedural flexibility. The results demonstrate how changes in complex knowledge structures contribute to competence development.

Development and evaluation of a prototype in-flight instrument flight rules (IFR) procedures trainer

NASA Technical Reports Server (NTRS)

Aaron, J. B., Jr.; Morris, G. G.

1981-01-01

An in-flight instrument flight rules (IFR) procedures trainer capable of providing simulated indications of instrument flight in a typical general aviation aircraft independent of ground based navigation aids was developed. The IFR navaid related instruments and circuits from an ATC 610J table top simulator were installed in a Cessna 172 aircraft and connected to its electrical power and pitot static systems. The benefits expected from this hybridization concept include increased safety by reducing the number of general aviation aircraft conducting IFR training flights in congested terminal areas, and reduced fuel use and instruction costs by lessening the need to fly to and from navaid equipped airports and by increased efficiency of the required in-flight training. Technical feasibility was demonstrated and the operational feasibility of the concept was evaluated. Results indicated that the in-flight simulator is an effective training device for teaching IFR procedural skills.

The IAEA’s activities on radiation protection in interventional cardiology

PubMed Central

Rehani, MM

2007-01-01

The International Atomic Energy Agency (IAEA) under its mandate of developing and applying standards of radiation safety has initiated a number of activities in recent years on radiation protection in interventional cardiology. These activities are implemented through four mechanisms, namely training, providing information through the website, research projects and assistance to Member States through Technical Cooperation (TC) projects. Major international initiatives have been taken in the area of training where more than half a dozen regional training courses have been conducted for cardiologists from over 50 countries. Additionally four national training events for over 300 medical and paramedical staff members involved in interventional procedures were held. The training material is freely available on CD from the IAEA. The newly established website provides information on radiation protection issues [1]. Two coordinated research projects have just been completed where peak skin doses to patients undergoing high dose interventional procedures were studied and factors to manage patient doses were identified. The technical cooperation projects involving protection in cardiac interventional procedures have 30 countries as participants. PMID:21614275

Comparison of IPSM 1990 photon dosimetry code of practice with IAEA TRS‐398 and AAPM TG‐51.

PubMed Central

Henríquez, Francisco Cutanda

2009-01-01

Several codes of practice for photon dosimetry are currently used around the world, supported by different organizations. A comparison of IPSM 1990 with both IAEA TRS‐398 and AAPM TG‐51 has been performed. All three protocols are based on the calibration of ionization chambers in terms of standards of absorbed dose to water, as it is the case with other modern codes of practice. This comparison has been carried out for photon beams of nominal energies: 4 MV, 6 MV, 8 MV, 10 MV and 18 MV. An NE 2571 graphite ionization chamber was used in this study, cross‐calibrated against an NE 2611A Secondary Standard, calibrated in the National Physical Laboratory (NPL). Absolute dose in reference conditions was obtained using each of these three protocols including: beam quality indices, beam quality conversion factors both theoretical and NPL experimental ones, correction factors for influence quantities and absolute dose measurements. Each protocol recommendations have been strictly followed. Uncertainties have been obtained according to the ISO Guide to the Expression of Uncertainty in Measurement. Absorbed dose obtained according to all three protocols agree within experimental uncertainty. The largest difference between absolute dose results for two protocols is obtained for the highest energy: 0.7% between IPSM 1990 and IAEA TRS‐398 using theoretical beam quality conversion factors. PACS number: 87.55.tm

Development of an Overlay Design Procedure for Composite Pavements

DOT National Transportation Integrated Search

2017-09-01

The composite overlay design procedure currently used by ODOT sometimes produces very large overlay thicknesses that are deemed structurally unnecessary, especially for composite pavements already with thick asphalt overlays. This study was initiated...

Development of multidisciplinary design optimization procedures for smart composite wings and turbomachinery blades

NASA Astrophysics Data System (ADS)

Jha, Ratneshwar

Multidisciplinary design optimization (MDO) procedures have been developed for smart composite wings and turbomachinery blades. The analysis and optimization methods used are computationally efficient and sufficiently rigorous. Therefore, the developed MDO procedures are well suited for actual design applications. The optimization procedure for the conceptual design of composite aircraft wings with surface bonded piezoelectric actuators involves the coupling of structural mechanics, aeroelasticity, aerodynamics and controls. The load carrying member of the wing is represented as a single-celled composite box beam. Each wall of the box beam is analyzed as a composite laminate using a refined higher-order displacement field to account for the variations in transverse shear stresses through the thickness. Therefore, the model is applicable for the analysis of composite wings of arbitrary thickness. Detailed structural modeling issues associated with piezoelectric actuation of composite structures are considered. The governing equations of motion are solved using the finite element method to analyze practical wing geometries. Three-dimensional aerodynamic computations are performed using a panel code based on the constant-pressure lifting surface method to obtain steady and unsteady forces. The Laplace domain method of aeroelastic analysis produces root-loci of the system which gives an insight into the physical phenomena leading to flutter/divergence and can be efficiently integrated within an optimization procedure. The significance of the refined higher-order displacement field on the aeroelastic stability of composite wings has been established. The effect of composite ply orientations on flutter and divergence speeds has been studied. The Kreisselmeier-Steinhauser (K-S) function approach is used to efficiently integrate the objective functions and constraints into a single envelope function. The resulting unconstrained optimization problem is solved using the

Bio-Oil Analysis Laboratory Procedures | Bioenergy | NREL

Science.gov Websites

Bio-Oil Analysis Laboratory Procedures Bio-Oil Analysis Laboratory Procedures NREL develops standard procedures have been validated and allow for reliable bio-oil analysis. Procedures Determination different hydroxyl groups (-OH) in pyrolysis bio-oil: aliphatic-OH, phenolic-OH, and carboxylic-OH. Download

A methodology for TLD postal dosimetry audit of high-energy radiotherapy photon beams in non-reference conditions.

PubMed

Izewska, Joanna; Georg, Dietmar; Bera, Pranabes; Thwaites, David; Arib, Mehenna; Saravi, Margarita; Sergieva, Katia; Li, Kaibao; Yip, Fernando Garcia; Mahant, Ashok Kumar; Bulski, Wojciech

2007-07-01

A strategy for national TLD audit programmes has been developed by the International Atomic Energy Agency (IAEA). It involves progression through three sequential dosimetry audit steps. The first step audits are for the beam output in reference conditions for high-energy photon beams. The second step audits are for the dose in reference and non-reference conditions on the beam axis for photon and electron beams. The third step audits involve measurements of the dose in reference, and non-reference conditions off-axis for open and wedged symmetric and asymmetric fields for photon beams. Through a co-ordinated research project the IAEA developed the methodology to extend the scope of national TLD auditing activities to more complex audit measurements for regular fields. Based on the IAEA standard TLD holder for high-energy photon beams, a TLD holder was developed with horizontal arm to enable measurements 5cm off the central axis. Basic correction factors were determined for the holder in the energy range between Co-60 and 25MV photon beams. New procedures were developed for the TLD irradiation in hospitals. The off-axis measurement methodology for photon beams was tested in a multi-national pilot study. The statistical distribution of dosimetric parameters (off-axis ratios for open and wedge beam profiles, output factors, wedge transmission factors) checked in 146 measurements was 0.999+/-0.012. The methodology of TLD audits in non-reference conditions with a modified IAEA TLD holder has been shown to be feasible.

A comparative study of 129I content in environmental standard materials IAEA-375, NIST SRM 4354 and NIST SRM 4357 by Thermal Ionization Mass Spectrometry and Accelerator Mass Spectrometry.

PubMed

Olson, John; Adamic, Mary; Snyder, Darin; Brookhart, Jacob; Hahn, Paula; Watrous, Matthew

2017-08-01

Iodine environmental measurements have consistently been validated in the literature using the standard material IAEA-375, soil collected approximately 160 miles northeast of Chernobyl, which is currently the only soil/sediment material with a certified 129 I activity. IAEA-375 has not been available for purchase since approximately 2010. Two other standard materials that are available (NIST SRM 4354, freshwater lake sediment and NIST SRM 4357, ocean sediment) have certified activities for a variety of radionuclides but not for 129 I. This paper reports a comparison of TIMS and AMS data for all three standards. Copyright © 2017. Published by Elsevier Ltd.

[Further development and validation of a clinical auditing procedure for rehabilitation facilities].

PubMed

Meixner, K; Lubenow, B; Brückner, U; Gerdes, N

2006-06-01

Visitations (audits) are considered an instrument of external quality assurance by which the structural and organizational set-up of health facilities can be assessed on site by external experts. The Deutsche Rentenversicherung Bund (including the former Bundesversicherungsanstalt für Angestellte, BfA, the statutory pension insurance agency for white collar employees) is the largest body responsible for rehabilitation in Germany, and it regularly carries out visitations in the approximately 650 rehab centres it sends its patients to. The project presented in this article aimed at developing a manual with detailed descriptions of the procedures and criteria of the assessment, as well as at checking the inter-rater-reliability of the assessment. The manual was developed in cooperation with experts of the Deutsche Rentenversicherung Bund. It contains a description of the areas to be assessed during a visitation as well as leading questions and criteria for the evaluation of single features. The manual was examined in "test visitations" in 10 centres, each of which was visited by three visitation teams (1 medical and 1 administrative expert) simultaneously. When the resulting 30 assessments were compared, the criterion "overall quality of the centre" (which was assessed on a 10-point scale) showed precise agreement in 47 %, and a deviation by 1 point in 33 % of the cases. Single features assessed on a three-point scale (no improvement needed/improvement recommended/immediate improvement obligatory) resulted in precise agreement in between 80 % ("medical and therapeutic processes") and 86 % ("structural features") of the cases. Two-point scales (condition fulfilled or not fulfilled) showed an agreement between 89 % ("internal quality management") and 97 % ("single structural features"). In order to maintain and further develop this good inter-rater-reliability, the visitors of Deutsche Rentenversicherung Bund are continually trained in applying the visitation manual

Development of an accelerated creep testing procedure for geosynthetics.

DOT National Transportation Integrated Search

1997-09-01

The report presents a procedure for predicting creep strains of geosynthetics using creep tests at elevated temperatures. Creep testing equipment was constructed and tests were performed on two types of geosynthetics: High Density Polyethylene (HDPE)...

Haeckel or Hennig? The Gordian Knot of Characters, Development, and Procedures in Phylogeny.

ERIC Educational Resources Information Center

Dupuis, Claude

1984-01-01

Discusses the conditions for validating customary phylogenetic procedures. Concludes that the requisites of homogeneity and completeness for proved short lineages seem satisfied by the Hennigian but not the Haeckelian procedure. The epistemological antinomy of the two procedures is emphasized for the first time. (Author/RH)

Development of a Meso-Scale SMA-Based Torsion Actuator for Image-Guided Procedures.

PubMed

Sheng, Jun; Gandhi, Dheeraj; Gullapalli, Rao; Simard, J Marc; Desai, Jaydev P

2017-02-01

This paper presents the design, modeling, and control of a meso-scale torsion actuator based on shape memory alloy (SMA) for image-guided surgical procedures. Developing a miniature torsion actuator is challenging, but it opens the possibility of significantly enhancing the robot agility and maneuverability. The proposed torsion actuator is bi-directionally actuated by a pair of antagonistic SMA torsion springs through alternate Joule heating and natural cooling. The torsion actuator is integrated into a surgical robot prototype to demonstrate its working performance in the humid environment under C-Arm CT image guidance.

Development of a Meso-Scale SMA-Based Torsion Actuator for Image-Guided Procedures

PubMed Central

Sheng, Jun; Gandhi, Dheeraj; Gullapalli, Rao; Simard, J. Marc; Desai, Jaydev P.

2016-01-01

This paper presents the design, modeling, and control of a meso-scale torsion actuator based on shape memory alloy (SMA) for image-guided surgical procedures. Developing a miniature torsion actuator is challenging, but it opens the possibility of significantly enhancing the robot agility and maneuverability. The proposed torsion actuator is bi-directionally actuated by a pair of antagonistic SMA torsion springs through alternate Joule heating and natural cooling. The torsion actuator is integrated into a surgical robot prototype to demonstrate its working performance in the humid environment under C-Arm CT image guidance. PMID:28210189

Series expansion of the modified Einstein Procedure

Treesearch

Seema Chandrakant Shah-Fairbank

2009-01-01

This study examines calculating total sediment discharge based on the Modified Einstein Procedure (MEP). A new procedure based on the Series Expansion of the Modified Einstein Procedure (SEMEP) has been developed. This procedure contains four main modifications to MEP. First, SEMEP solves the Einstein integrals quickly and accurately based on a series expansion. Next,...

Best Practices for NPT Transit Matching

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gilligan, Kimberly V.; Whitaker, J. Michael; Oakberg, John A.

2016-09-01

Transit matching is the process for relating or matching reports of shipments and receipts submitted to the International Atomic Energy Agency (IAEA). Transit matching is a component used by the IAEA in drawing safeguards conclusions and performing investigative analysis. Transit matching is part of IAEA safeguards activities and the State evaluation process, and it is included in the annual Safeguards Implementation Report (SIR). Annually, the IAEA currently receives reports of ~900,000 nuclear material transactions, of which ~500,000 are for domestic and foreign transfers. Of these the IAEA software can automatically match (i.e., machine match) about 95% of the domestic transfersmore » and 25% of the foreign transfers. Given the increasing demands upon IAEA resources, it is highly desirable for the machine-matching process to match as many transfers as possible. Researchers at Oak Ridge National Laboratory (ORNL) have conducted an investigation funded by the National Nuclear Security Administration through the Next Generation Safeguards Initiative to identify opportunities to strengthen IAEA transit matching. Successful matching, and more specifically machine matching, is contingent on quality data from the reporting States. In February 2016, ORNL hosted representatives from three States, the IAEA, and Euratom to share results from past studies and to discuss the processes, policies, and procedures associated with State reporting for transit matching. Drawing on each entity's experience and knowledge, ORNL developed a best practices document to be shared with the international safeguards community to strengthen transit matching. This paper shares the recommendations that resulted from this strategic meeting and the next steps being taken to strengthen transit matching.« less

Diagnostic flexible pharyngo-laryngoscopy: development of a procedure specific assessment tool using a Delphi methodology.

PubMed

Melchiors, Jacob; Henriksen, Mikael Johannes Vuokko; Dikkers, Frederik G; Gavilán, Javier; Noordzij, J Pieter; Fried, Marvin P; Novakovic, Daniel; Fagan, Johannes; Charabi, Birgitte W; Konge, Lars; von Buchwald, Christian

2018-05-01

Proper training and assessment of skill in flexible pharyngo-laryngoscopy are central in the education of otorhinolaryngologists. To facilitate an evidence-based approach to curriculum development in this field, a structured analysis of what constitutes flexible pharyngo-laryngoscopy is necessary. Our aim was to develop an assessment tool based on this analysis. We conducted an international Delphi study involving experts from twelve countries in five continents. Utilizing reiterative assessment, the panel defined the procedure and reached consensus (defined as 80% agreement) on the phrasing of an assessment tool. FIFTY PANELISTS COMPLETED THE DELPHI PROCESS. THE MEDIAN AGE OF THE PANELISTS WAS 44 YEARS (RANGE 33-64 YEARS). MEDIAN EXPERIENCE IN OTORHINOLARYNGOLOGY WAS 15 YEARS (RANGE 6-35 YEARS). TWENTY-FIVE WERE SPECIALIZED IN LARYNGOLOGY, 16 WERE HEAD AND NECK SURGEONS, AND NINE WERE GENERAL OTORHINOLARYNGOLOGISTS. AN ASSESSMENT TOOL WAS CREATED CONSISTING OF TWELVE DISTINCT ITEMS.: Conclusion The gathering of validity evidence for assessment of core procedural skills within Otorhinolaryngology is central to the development of a competence-based education. The use of an international Delphi panel allows for the creation of an assessment tool which is widely applicable and valid. This work allows for an informed approach to technical skills training for flexible pharyngo-laryngoscopy and as further validity evidence is gathered allows for a valid assessment of clinical performance within this important skillset.

How to develop a Standard Operating Procedure for sorting unfixed cells

PubMed Central

Schmid, Ingrid

2012-01-01

Written Standard Operating Procedures (SOPs) are an important tool to assure that recurring tasks in a laboratory are performed in a consistent manner. When the procedure covered in the SOP involves a high-risk activity such as sorting unfixed cells using a jet-in-air sorter, safety elements are critical components of the document. The details on sort sample handling, sorter set-up, validation, operation, troubleshooting, and maintenance, personal protective equipment (PPE), and operator training, outlined in the SOP are to be based on careful risk assessment of the procedure. This review provides background information on the hazards associated with sorting of unfixed cells and the process used to arrive at the appropriate combination of facility design, instrument placement, safety equipment, and practices to be followed. PMID:22381383

How to develop a standard operating procedure for sorting unfixed cells.

PubMed

Schmid, Ingrid

2012-07-01

Written standard operating procedures (SOPs) are an important tool to assure that recurring tasks in a laboratory are performed in a consistent manner. When the procedure covered in the SOP involves a high-risk activity such as sorting unfixed cells using a jet-in-air sorter, safety elements are critical components of the document. The details on sort sample handling, sorter set-up, validation, operation, troubleshooting, and maintenance, personal protective equipment (PPE), and operator training, outlined in the SOP are to be based on careful risk assessment of the procedure. This review provides background information on the hazards associated with sorting of unfixed cells and the process used to arrive at the appropriate combination of facility design, instrument placement, safety equipment, and practices to be followed. Copyright © 2012 Elsevier Inc. All rights reserved.

Revisiting the destination ranking procedure in development of an Intervening Opportunities Model for public transit trip distribution

NASA Astrophysics Data System (ADS)

Nazem, Mohsen; Trépanier, Martin; Morency, Catherine

2015-01-01

An Enhanced Intervening Opportunities Model (EIOM) is developed for Public Transit (PT). This is a distribution supply dependent model, with single constraints on trip production for work trips during morning peak hours (6:00 a.m.-9:00 a.m.) within the Island of Montreal, Canada. Different data sets, including the 2008 Origin-Destination (OD) survey of the Greater Montreal Area, the 2006 Census of Canada, GTFS network data, along with the geographical data of the study area, are used. EIOM is a nonlinear model composed of socio-demographics, PT supply data and work location attributes. An enhanced destination ranking procedure is used to calculate the number of spatially cumulative opportunities, the basic variable of EIOM. For comparison, a Basic Intervening Opportunities Model (BIOM) is developed by using the basic destination ranking procedure. The main difference between EIOM and BIOM is in the destination ranking procedure: EIOM considers the maximization of a utility function composed of PT Level Of Service and number of opportunities at the destination, along with the OD trip duration, whereas BIOM is based on a destination ranking derived only from OD trip durations. Analysis confirmed that EIOM is more accurate than BIOM. This study presents a new tool for PT analysts, planners and policy makers to study the potential changes in PT trip patterns due to changes in socio-demographic characteristics, PT supply, and other factors. Also it opens new opportunities for the development of more accurate PT demand models with new emergent data such as smart card validations.

Developing standard operating procedures for gene drive research in disease vector mosquitoes.

PubMed

Adelman, Zach N; Pledger, David; Myles, Kevin M

2017-12-01

Numerous arthropod species represent potential targets for gene-drive-based population suppression or replacement, including those that transmit diseases, damage crops, or act as deleterious invasive species. Containment measures for gene drive research in arthropods have been discussed in the literature, but the importance of developing safe and effective standard operating procedures (SOPs) for these types of experiments has not been adequately addressed. Concisely written SOPs link safe work practices, containment measures, institutional training, and research-specific protocols. Here we discuss information to be considered by principal investigators, biosafety officers, and institutional biosafety committees as they work together to develop SOPs for experiments involving gene drive in arthropods, and describe various courses of action that can be used to maintain the effectiveness of SOPs through evaluation and revision. The information provided herein will be especially useful to investigators and regulatory personnel who may lack extensive experience working with arthropods under containment conditions.

Development of ecotoxicology procedures for use in assessing health of coral reefs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davies, P.S.; Marubini, F.

1995-12-31

There is widespread concern over the apparent worldwide decline in the health of coral reefs. However, assessment methods, other than long-term monitoring, have not yet been attempted. To remedy this the authors are developing ecotoxicology procedures to assess the effects of water quality factors on the corals themselves. Because of the problems of working with large, attached organisms, the authors have concentrated on developing small clonal preparations from corals with both a branching and a massive growth-form. For branching corals, tips (`nubbins`) are removed, and the cut surface ground smooth before cementing to 30mm x 30mm acrylic squares. Cores, ormore » `explants`, 25mm in diameter are removed from massive corals and cemented into injection-moulded plastic cups, to protect the cut surfaces of the skeleton. Trays of up to 18 nubbins and explants may then be transferred to the reef, where they are affixed to previously installed concrete breeze blocks. They may then be retrieved as required to assess the effects of water quality upon them. For laboratory ecotoxicology experiments, the authors have devised a system of artificial lighting, using halide lamps, to grow coral nubbins and explants under controlled conditions. To test the effects of pollutants, the authors use measurements of respiration, photosynthesis and skeletal growth rate. Growth is measured by a very simple buoyant weighing procedure, which requires only an analytical laboratory balance, and an easily-constructed plastic box-shaped chamber. The method is sufficiently sensitive to measure growth over a 24 hour period in some fast-growing corals. The authors will describe the results of initial experiments, carried out at the Bellairs Research Institute, Barbados, on the effects of different levels of phosphate and nitrate in the seawater. For the first time, they are able to demonstrate the concentration-related decrease in growth rate associated with nitrate eutrophication.« less

NHEXAS PHASE I MARYLAND STUDY--STANDARD OPERATING PROCEDURE FOR PREPARATION OF STANDARD OPERATING PROCEDURES (G01)

EPA Science Inventory

The purpose of this SOP is to develop a consistent method and style for all Emory University/Harvard University/Johns Hopkins University standard operating procedures. SOPs are necessary to document all procedures, methods, and techniques used in the NHEXAS investigations. Deve...

Acceptance procedures for dense-graded mixes

DOT National Transportation Integrated Search

2001-03-01

Recent literature related to acceptance procedures for dense-graded mixtures is summarized. Current state of practice and development of acceptance procedures are reviewed. Many agencies are reducing the number of process control-related parameters i...

A clinical audit programme for diagnostic radiology: the approach adopted by the International Atomic Energy Agency.

PubMed

Faulkner, K; Järvinen, H; Butler, P; McLean, I D; Pentecost, M; Rickard, M; Abdullah, B

2010-01-01

The International Atomic Energy Agency (IAEA) has a mandate to assist member states in areas of human health and particularly in the use of radiation for diagnosis and treatment. Clinical audit is seen as an essential tool to assist in assuring the quality of radiation medicine, particularly in the instance of multidisciplinary audit of diagnostic radiology. Consequently, an external clinical audit programme has been developed by the IAEA to examine the structure and processes existent at a clinical site, with the basic objectives of: (1) improvement in the quality of patient care; (2) promotion of the effective use of resources; (3) enhancement of the provision and organisation of clinical services; (4) further professional education and training. These objectives apply in four general areas of service delivery, namely quality management and infrastructure, patient procedures, technical procedures and education, training and research. In the IAEA approach, the audit process is initiated by a request from the centre seeking the audit. A three-member team, comprising a radiologist, medical physicist and radiographer, subsequently undertakes a 5-d audit visit to the clinical site to perform the audit and write the formal audit report. Preparation for the audit visit is crucial and involves the local clinical centre completing a form, which provides the audit team with information on the clinical centre. While all main aspects of clinical structure and process are examined, particular attention is paid to radiation-related activities as described in the relevant documents such as the IAEA Basic Safety Standards, the Code of Practice for Dosimetry in Diagnostic Radiology and related equipment and quality assurance documentation. It should be stressed, however, that the clinical audit does not have any regulatory function. The main purpose of the IAEA approach to clinical audit is one of promoting quality improvement and learning. This paper describes the background to

34 CFR 303.420 - Due process procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... infant's or toddler's development is so rapid that undue delay could be potentially harmful. [58 FR 40959... AND REHABILITATIVE SERVICES, DEPARTMENT OF EDUCATION EARLY INTERVENTION PROGRAM FOR INFANTS AND... Children § 303.420 Due process procedures. Each system must include written procedures including procedures...

34 CFR 303.420 - Due process procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... infant's or toddler's development is so rapid that undue delay could be potentially harmful. [58 FR 40959... AND REHABILITATIVE SERVICES, DEPARTMENT OF EDUCATION EARLY INTERVENTION PROGRAM FOR INFANTS AND... Children § 303.420 Due process procedures. Each system must include written procedures including procedures...

Development of low-cost welding procedures for thick sections of HY-150 steel

NASA Technical Reports Server (NTRS)

Schmidt, P. M.; Snow, R. S.

1972-01-01

Low cost welding procedures were developed for welding 6-inch thick HY-150 steel to be used in the manufacture of large diameter motor case Y rings and nozzle attachment flanges. An extensive investigation was made of the mechanical and metallurgical properties and fracture toughness of HY-150 base plate and welds made with manual shielded metal arc process and semi-automatic gas metal arc process in the flat position. Transverse tensiles, all-weld metal tensiles, Charpy V-notch specimens and edge notched bend specimens were tested in the course of the program. In addition metallographic studies and hardness tests were performed on the weld, weld HAZ and base metal. The results of the work performed indicate that both the shielded metal arc and gas metal arc processes are capable of producing consistently sound welds as determined by radiographic and ultrasonic inspection. In addition, the weld metal, deposited by each process was found to exhibit a good combination of strength and toughness such that the selection of a rolled and welded procedure for fabricating rocket motor case components would appear to be technically feasible.

Development of a Virtual Reality Simulator for Natural Orifice Translumenal Endoscopic Surgery (NOTES) Cholecystectomy Procedure.

PubMed

Ahn, Woojin; Dargar, Saurabh; Halic, Tansel; Lee, Jason; Li, Baichun; Pan, Junjun; Sankaranarayanan, Ganesh; Roberts, Kurt; De, Suvranu

2014-01-01

The first virtual-reality-based simulator for Natural Orifice Translumenal Endoscopic Surgery (NOTES) is developed called the Virtual Translumenal Endoscopic Surgery Trainer (VTEST^TM). VTEST^TM aims to simulate hybrid NOTES cholecystectomy procedure using a rigid scope inserted through the vaginal port. The hardware interface is designed for accurate motion tracking of the scope and laparoscopic instruments to reproduce the unique hand-eye coordination. The haptic-enabled multimodal interactive simulation includes exposing the Calot's triangle and detaching the gall bladder while performing electrosurgery. The developed VTEST^TM was demonstrated and validated at NOSCAR 2013.

Training tissue bank operators: the International Atomic Energy Agency (IAEA)/National University of Singapore (NUS) 10 years of experience.

PubMed

Nather, A; Phillips, G O; Morales Pedraza, Jorge; Lee, Chris C W

2009-05-01

National University of Singapore (NUS) was appointed by IAEA to become IAEA/NUS Regional Training Centre (RTC) for Asia and the Pacific region in September 1996. The Government of Singapore (represented by the Ministry of Environment) with the National Science and Technology Board as the funding agency awarded a grant of S$225,500 to build a new purpose-built tissue bank to be the Regional Training Centre. National University Hospital provided a space of 2,000 square feet for this purpose. The first Diploma Course was launched on 3 November 1997 with 17 candidates with the first NUS Diploma Examination being held in October 1998. Between November 1997 and April 2007, a total of nine courses were conducted by RTC with a total of 180 tissue bank operators, 133 from Asia and the Pacific region (13 countries including 2 from Iran), 14 from Africa (Algeria, Egypt, Libya, Egypt, South Africa and Zambia), 6 from Latin America (Brazil, Chile, Cuba, Peru and Uruguay), 9 from Europe (Greece, Slovakia, Poland, Ukraine) and 2 from Australia. The last batch (ninth batch) involved twenty students registered in April 2007 and will be due to sit for the terminal examination only in April 2008.

Procedural Portfolio Planning in Plastic Surgery, Part 2: Collaboration Between Surgeons and Hospital Administrators to Develop a Funds Flow Model for Procedures Performed at an Academic Medical Center.

PubMed

Hultman, Charles Scott

2016-06-01

Although plastic surgeons make important contributions to the clinical, educational, and research missions of academic medical centers (AMCs), determining the financial value of a plastic surgery service can be difficult, due to complex cost accounting systems. We analyzed the financial impact of plastic surgery on an AMC, by examining the contribution margins and operating income of surgical procedures. We collaborated with hospital administrators to implement 3 types of strategic changes: (1) growth of areas with high contribution margin, (2) curtailment of high-risk procedures with negative contribution margin, (3) improved efficiency of mission-critical services with high resource consumption. Outcome measures included: facility charges, hospital collections, contribution margin, operating margin, and operating room times. We also studied the top 50 Current Procedural Terminology codes (total case number × charge/case), ranking procedures for profitability, as determined by operating margin. During the 2-year study period, we had no turnover in faculty; did not pursue any formal marketing; did not change our surgical fees, billing system, or payer mix; and maintained our commitment to indigent care. After rebalancing our case mix, through procedural portfolio planning, average hospital operating income/procedure increased from $-79 to $+816. Volume and diversity of cases increased, with no change in payer mix. Although charges/case decreased, both contribution margin and operating margin increased, due to improved throughput and decreased operating room times. The 5 most profitable procedures for the hospital were hernia repair, mandibular osteotomy, hand skin graft, free fibula flap, and head and neck flap, whereas the 5 least profitable were latissimus breast reconstruction, craniosynostosis repair, free-flap breast reconstruction, trunk skin graft, and cutaneous free flap. Total operating income for the hospital, from plastic surgery procedures, increased

Formalizing procedures for operations automation, operator training and spacecraft autonomy

NASA Technical Reports Server (NTRS)

Lecouat, Francois; Desaintvincent, Arnaud

1994-01-01

The generation and validation of operations procedures is a key task of mission preparation that is quite complex and costly. This has motivated the development of software applications providing support for procedures preparation. Several applications have been developed at MATRA MARCONI SPACE (MMS) over the last five years. They are presented in the first section of this paper. The main idea is that if procedures are represented in a formal language, they can be managed more easily with a computer tool and some automatic verifications can be performed. One difficulty is to define a formal language that is easy to use for operators and operations engineers. From the experience of the various procedures management tools developed in the last five years (including the POM, EOA, and CSS projects), MMS has derived OPSMAKER, a generic tool for procedure elaboration and validation. It has been applied to quite different types of missions, ranging from crew procedures (PREVISE system), ground control centers management procedures (PROCSU system), and - most relevant to the present paper - satellite operation procedures (PROCSAT developed for CNES, to support the preparation and verification of SPOT 4 operation procedures, and OPSAT for MMS telecom satellites operation procedures).

24 CFR 983.51 - Owner proposal selection procedures.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 4 2011-04-01 2011-04-01 false Owner proposal selection procedures... proposal selection procedures. (a) Procedures for selecting PBV proposals. The PHA administrative plan must describe the procedures for owner submission of PBV proposals and for PHA selection of PBV proposals...

Development of procedures for programmable proximity aperture lithography

NASA Astrophysics Data System (ADS)

Whitlow, H. J.; Gorelick, S.; Puttaraksa, N.; Napari, M.; Hokkanen, M. J.; Norarat, R.

2013-07-01

Programmable proximity aperture lithography (PPAL) with MeV ions has been used in Jyväskylä and Chiang Mai universities for a number of years. Here we describe a number of innovations and procedures that have been incorporated into the LabView-based software. The basic operation involves the coordination of the beam blanker and five motor-actuated translators with high accuracy, close to the minimum step size with proper anti-collision algorithms. By using special approaches, such writing calibration patterns, linearisation of position and careful backlash correction the absolute accuracy of the aperture size and position, can be improved beyond the standard afforded by the repeatability of the translator end-point switches. Another area of consideration has been the fluence control procedures. These involve control of the uniformity of the beam where different approaches for fluence measurement such as simultaneous aperture current and the ion current passing through the aperture using a Faraday cup are used. Microfluidic patterns may contain many elements that make-up mixing sections, reaction chambers, separation columns and fluid reservoirs. To facilitate conception and planning we have implemented a .svg file interpreter, that allows the use of scalable vector graphics files produced by standard drawing software for generation of patterns made up of rectangular elements.

Procedures in complex systems: the airline cockpit.

PubMed

Degani, A; Wiener, E L

1997-05-01

In complex human-machine systems, successful operations depend on an elaborate set of procedures which are specified by the operational management of the organization. These procedures indicate to the human operator (in this case the pilot) the manner in which operational management intends to have various tasks done. The intent is to provide guidance to the pilots and to ensure a safe, logical, efficient, and predictable (standardized) means of carrying out the objectives of the job. However, procedures can become a hodge-podge. Inconsistent or illogical procedures may lead to noncompliance by operators. Based on a field study with three major airlines, the authors propose a model for procedure development called the "Four P's": philosophy, policies, procedures, and practices. Using this model as a framework, the authors discuss the intricate issue of designing flight-deck procedures, and propose a conceptual approach for designing any set of procedures. The various factors, both external and internal to the cockpit, that must be considered for procedure design are presented. In particular, the paper addresses the development of procedures for automated cockpits--a decade-long, and highly controversial issue in commercial aviation. Although this paper is based on airline operations, we assume that the principles discussed here are also applicable to other high-risk supervisory control systems, such as space flight, manufacturing process control, nuclear power production, and military operations.

Post-upgrade testing on a radiotherapy oncology information system with an embedded record and verify system following the IAEA Human Health Report No. 7 recommendations.

PubMed

Nyathi, Thulani; Colyer, Christopher; Bhardwaj, Anup Kumar; Rijken, James; Morton, Jason

2016-06-01

Record and verify (R&V) systems have proven that their application in radiotherapy clinics leads to a significant reduction in mis-treatments of patients. The purpose of this technical note is to share our experience of acceptance testing, commissioning and setting up a quality assurance programme for the MOSAIQ® oncology information system and R&V system after upgrading from software version 2.41 to 2.6 in a multi-vendor, multi-site environment. Testing was guided primarily by the IAEA Human Report No. 7 recommendations, but complemented by other departmental workflow specific tests. To the best of our knowledge, this is the first time successful implementation of the IAEA Human Health Report Series No. 7 recommendations have been reported in the literature. Copyright © 2016 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

Involving service users in trials: developing a standard operating procedure

PubMed Central

2013-01-01

Background Many funding bodies require researchers to actively involve service users in research to improve relevance, accountability and quality. Current guidance to researchers mainly discusses general principles. Formal guidance about how to involve service users operationally in the conduct of trials is lacking. We aimed to develop a standard operating procedure (SOP) to support researchers to involve service users in trials and rigorous studies. Methods Researchers with experience of involving service users and service users who were contributing to trials collaborated with the West Wales Organisation for Rigorous Trials in Health, a registered clinical trials unit, to develop the SOP. Drafts were prepared in a Task and Finish Group, reviewed by all co-authors and amendments made. Results We articulated core principles, which defined equality of service users with all other research team members and collaborative processes underpinning the SOP, plus guidance on how to achieve these. We developed a framework for involving service users in research that defined minimum levels of collaboration plus additional consultation and decision-making opportunities. We recommended service users be involved throughout the life of a trial, including planning and development, data collection, analysis and dissemination, and listed tasks for collaboration. We listed people responsible for involving service users in studies and promoting an inclusive culture. We advocate actively involving service users as early as possible in the research process, with a minimum of two on all formal trial groups and committees. We propose that researchers protect at least 1% of their total research budget as a minimum resource to involve service users and allow enough time to facilitate active involvement. Conclusions This SOP provides guidance to researchers to involve service users successfully in developing and conducting clinical trials and creating a culture of actively involving service

Using the Traffic monitoring guide to develop a truck weight sampling procedure for use in Virginia : final report.

DOT National Transportation Integrated Search

1992-01-01

The Traffic Monitoring Guide (TMG) provides a method for the development of a statistically based procedure to monitor traffic characteristics such as traffic loadings. Truck weight data in particular are a major element of the pavement management pr...

Obtaining accreditation by the pharmacy compounding accreditation board, part 2: developing essential standard operating procedures.

PubMed

Cabaleiro, Joe

2007-01-01

A key component of qualifying for accreditation with the Pharmacy Compounding Accreditation Board is having a set of comprehensive standard operating procedures that are being used by the pharmacy staff. The three criteria in standard operating procedures for which the Pharmacy Compounding Accreditation Board looks are: (1)written standard operating procedures; (2)standard operating procedures that reflect what the organization actualy does; and (3) whether the written standard operating procedures are implemented. Following specified steps in the preparation of standard operating procedures will result in procedures that meet Pharmacy Compounding Accreditation Board Requirements, thereby placing pharmacies one step closer to qualifying for accreditation.

Development and validation of procedures for assessment of competency of non-pharmacists in extemporaneous dispensing.

PubMed

Donnelly, Ryan F; McNally, Martin J; Barry, Johanne G

2009-02-01

To develop and validate procedures that may be suitable for assessment of competency of two groups of non-pharmacist staff (pharmacy students and trainee support staff) in extemporaneous dispensing. This is important given the prospect of remote supervision of community pharmacies in the UK. Analytical methods were validated according to International Conference on Harmonisation specifications and procedures were optimized to allow efficient drug extraction. This permitted straightforward determination of drug content in extemporaneously prepared lidocaine hydrochloride mouthwashes and norfloxacin creams and suspensions prepared by 10 participants recruited to represent the two groups of non-pharmacist staff. All 10 participants had completed the extemporaneous dispensing of all three products within 90 min. Extraction and analysis took approximately 15 min for each lidocaine hydrochloride mouthwash and 30 min for each diluted norfloxacin cream and norfloxacin suspension. The mean drug concentrations in lidocaine hydrochloride mouthwashes and diluted norfloxacin creams were within what are generally accepted as being pharmaceutically acceptable limits for drug content (100 +/- 5%) for both groups of participants. There was no significant difference in the mean drug concentration of norfloxacin suspensions prepared by the participant groups. However, it was notable that only one participant prepared a suspension containing a norfloxacin concentration that was within pharmaceutically acceptable limits (101.51%). A laboratory possessing suitable equipment and appropriately trained staff could cope readily with the large number of products prepared, for example, by a cohort of pre-registration students. Consequently, the validated procedures developed here could usefully be incorporated into the pre-registration examination for pharmacy students and a final qualifying examination for dispensers and pharmacy technicians. We believe that this is essential if the public

A unified framework for developing effective hygiene procedures for hands, environmental surfaces and laundry in healthcare, domestic, food handling and other settings

PubMed Central

Bloomfield, Sally F.; Carling, Philip C.; Exner, Martin

2017-01-01

Hygiene procedures for hands, surfaces and fabrics are central to preventing spread of infection in settings including healthcare, food production, catering, agriculture, public settings, and home and everyday life. They are used in situations including hand hygiene, clinical procedures, decontamination of environmental surfaces, respiratory hygiene, food handling, laundry hygiene, toilet hygiene and so on. Although the principles are common to all, approaches currently used in different settings are inconsistent. A concern is the use of inconsistent terminology which is misleading, especially to people we need to communicate with such as the public or cleaning professionals. This paper reviews the data on current approaches, alongside new insights to developing hygiene procedures. Using this data, we propose a more scientifically-grounded framework for developing procedures that maximize protection against infection, based on consistent principles and terminology, and applicable across all settings. A key feature is use of test models which assess the state of surfaces after treatment rather than product performance alone. This allows procedures that rely on removal of microbes to be compared with those employing chemical or thermal inactivation. This makes it possible to ensure that a consistent “safety target level” is achieved regardless of the type of procedure used, and allows us deliver maximum health benefit whilst ensuring prudent usage of antimicrobial agents, detergents, water and energy. PMID:28670508

Preliminary development of a workstation for craniomaxillofacial surgical procedures: introducing a computer-assisted planning and execution system.

PubMed

Gordon, Chad R; Murphy, Ryan J; Coon, Devin; Basafa, Ehsan; Otake, Yoshito; Al Rakan, Mohammed; Rada, Erin; Susarla, Srinivas; Susarla, Sriniras; Swanson, Edward; Fishman, Elliot; Santiago, Gabriel; Brandacher, Gerald; Liacouras, Peter; Grant, Gerald; Armand, Mehran

2014-01-01

Facial transplantation represents one of the most complicated scenarios in craniofacial surgery because of skeletal, aesthetic, and dental discrepancies between donor and recipient. However, standard off-the-shelf vendor computer-assisted surgery systems may not provide custom features to mitigate the increased complexity of this particular procedure. We propose to develop a computer-assisted surgery solution customized for preoperative planning, intraoperative navigation including cutting guides, and dynamic, instantaneous feedback of cephalometric measurements/angles as needed for facial transplantation and other related craniomaxillofacial procedures. We developed the Computer-Assisted Planning and Execution (CAPE) workstation to assist with planning and execution of facial transplantation. Preoperative maxillofacial computed tomography (CT) scans were obtained on 4 size-mismatched miniature swine encompassing 2 live face-jaw-teeth transplants. The system was tested in a laboratory setting using plastic models of mismatched swine, after which the system was used in 2 live swine transplants. Postoperative CT imaging was obtained and compared with the preoperative plan and intraoperative measures from the CAPE workstation for both transplants. Plastic model tests familiarized the team with the CAPE workstation and identified several defects in the workflow. Live swine surgeries demonstrated utility of the CAPE system in the operating room, showing submillimeter registration error of 0.6 ± 0.24 mm and promising qualitative comparisons between intraoperative data and postoperative CT imaging. The initial development of the CAPE workstation demonstrated that integration of computer planning and intraoperative navigation for facial transplantation are possible with submillimeter accuracy. This approach can potentially improve preoperative planning, allowing ideal donor-recipient matching despite significant size mismatch, and accurate surgical execution for numerous

24 CFR 246.31 - Procedures.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 2 2011-04-01 2011-04-01 false Procedures. 246.31 Section 246.31 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued) OFFICE OF ASSISTANT SECRETARY FOR HOUSING-FEDERAL HOUSING COMMISSIONER, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT...

24 CFR 246.31 - Procedures.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Procedures. 246.31 Section 246.31 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued) OFFICE OF ASSISTANT SECRETARY FOR HOUSING-FEDERAL HOUSING COMMISSIONER, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT...

24 CFR 246.22 - Procedures.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 2 2012-04-01 2012-04-01 false Procedures. 246.22 Section 246.22 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued) OFFICE OF ASSISTANT SECRETARY FOR HOUSING-FEDERAL HOUSING COMMISSIONER, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT...

24 CFR 246.31 - Procedures.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 24 Housing and Urban Development 2 2014-04-01 2014-04-01 false Procedures. 246.31 Section 246.31 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued) OFFICE OF ASSISTANT SECRETARY FOR HOUSING-FEDERAL HOUSING COMMISSIONER, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT...

24 CFR 246.22 - Procedures.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 2 2011-04-01 2011-04-01 false Procedures. 246.22 Section 246.22 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued) OFFICE OF ASSISTANT SECRETARY FOR HOUSING-FEDERAL HOUSING COMMISSIONER, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT...

24 CFR 246.22 - Procedures.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Procedures. 246.22 Section 246.22 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued) OFFICE OF ASSISTANT SECRETARY FOR HOUSING-FEDERAL HOUSING COMMISSIONER, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT...

24 CFR 246.31 - Procedures.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 2 2012-04-01 2012-04-01 false Procedures. 246.31 Section 246.31 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued) OFFICE OF ASSISTANT SECRETARY FOR HOUSING-FEDERAL HOUSING COMMISSIONER, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT...

24 CFR 246.22 - Procedures.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 24 Housing and Urban Development 2 2014-04-01 2014-04-01 false Procedures. 246.22 Section 246.22 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued) OFFICE OF ASSISTANT SECRETARY FOR HOUSING-FEDERAL HOUSING COMMISSIONER, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT...

24 CFR 246.22 - Procedures.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 2 2013-04-01 2013-04-01 false Procedures. 246.22 Section 246.22 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued) OFFICE OF ASSISTANT SECRETARY FOR HOUSING-FEDERAL HOUSING COMMISSIONER, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT...

24 CFR 246.31 - Procedures.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 2 2013-04-01 2013-04-01 false Procedures. 246.31 Section 246.31 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued) OFFICE OF ASSISTANT SECRETARY FOR HOUSING-FEDERAL HOUSING COMMISSIONER, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT...

National Economic Development Procedures Manual - Agricultural Flood Damage,

DTIC Science & Technology

1987-10-01

based on the conceptual framework of the Economic and Environmental Principles and Guidelines for Water and Related Land Resources Implementation...the planning process and the NED evaluacion ’- ". procedures for agriculture, as described in the P&G, are thei presented. Also identified are some...ood Ioss compu t at ion approach de ’(’ op4 t hie f I ond damage for hypothetical frequency flood events and weights the result to I V- II1. + . IV-11

Determination of absorbed dose to water for high-energy photon and electron beams-comparison of the standards DIN 6800-2 (1997), IAEA TRS 398 (2000) and DIN 6800-2 (2006).

PubMed

Zakaria, Golam Abu; Schuette, Wilhelm

2007-01-01

For the determination of the absorbed dose to water for high-energy photon and electron beams the IAEA code of practice TRS-398 (2000) is applied internationally. In Germany, the German dosimetry protocol DIN 6800-2 (1997) is used. Recently, the DIN standard has been revised and published as Draft National Standard DIN 6800-2 (2006). It has adopted widely the methodology and dosimetric data of the code of practice. This paper compares these three dosimetry protocols systematically and identifies similarities as well as differences. The investigation was done with 6 and 18 MV photon as well as 5 to 21 MeV electron beams. While only cylindrical chambers were used for photon beams, measurements of electron beams were performed using cylindrical as well as plane-parallel chambers. The discrepancies in the determination of absorbed dose to water between the three protocols were 0.4% for photon beams and 1.5% for electron beams. Comparative measurements showed a deviation of less than 0.5% between our measurements following protocol DIN 6800-2 (2006) and TLD inter-comparison procedure in an external audit.

Long-term outcome of catheter ablation for left posterior fascicular ventricular tachycardia with the development of left posterior fascicular block and characteristics of repeat procedures.

PubMed

Luo, Bin; Zhou, Gongbu; Guo, Xiaogang; Liu, Xu; Yang, Jiandu; Sun, Qi; Ma, Jian; Zhang, Shu

2017-06-01

The present study aimed to retrospectively investigate long-term clinical outcomes of patients undergoing catheter ablation of left posterior fascicular ventricular tachycardia (LPF-VT) with the development of left posterior fascicular block (LPF block) and characteristics of repeat procedures. A total of 195 patients (mean age 29.76±1.03years, 16.4% females) who underwent catheter ablation for LPF-VT were consecutively enrolled. The earliest ventricular potential with a single fused Purkinje potential (PP) during VT and the PP located in the inferior-apical or mid-apical septum during SR were targeted for linear ablation. The endpoint of the procedure was noninducible VT and development of new-onset LPF block. Follow-up with clinic visits or telephonic interviews, electrocardiogram (ECG), or Holter monitoring was performed after the procedure. With a median follow-up of 85 (18,181) months, 20 patients were censored and 152 of 175 (86.86%) patients had long-term freedom from VT after a single procedure. No statistical difference in the outcome of catheter ablation of LPF-VT was found between inducible and non-inducible groups (P=0.89). Twenty-three patients exhibited recurrent LPF-VT. Seven of 23 patients developed new-onset left upper septal ventricular tachycardia that was successfully ablated. All the patients undergoing repeat procedures had freedom from VT. No procedural complications occurred. Ablation of LPF-VT using the development of LPF block as the endpoint is associated with a high procedural success rate. No difference in freedom from LPF-VT was found between inducible and non-inducible patients. New-onset LPF block recovery and non-early PP-QRS interval can be the predictors of LPF-VT repeat procedure. Copyright © 2017 Elsevier B.V. All rights reserved.

Procedure for analysis and design of weaving sections : volume 1, research findings and development of techniques for application.

DOT National Transportation Integrated Search

1983-12-01

This research was performed to complete and advance the status of recently developed : procedures for analysis and design of weaving sections (known as the Leisch method and-initially published in the 1979 issue of ITE Journal). The objective was to ...

Development and Execution of Autonomous Procedures Onboard the International Space Station to Support the Next Phase of Human Space Exploration

NASA Technical Reports Server (NTRS)

Beisert, Susan; Rodriggs, Michael; Moreno, Francisco; Korth, David; Gibson, Stephen; Lee, Young H.; Eagles, Donald E.

2013-01-01

Now that major assembly of the International Space Station (ISS) is complete, NASA's focus has turned to using this high fidelity in-space research testbed to not only advance fundamental science research, but also demonstrate and mature technologies and develop operational concepts that will enable future human exploration missions beyond low Earth orbit. The ISS as a Testbed for Analog Research (ISTAR) project was established to reduce risks for manned missions to exploration destinations by utilizing ISS as a high fidelity micro-g laboratory to demonstrate technologies, operations concepts, and techniques associated with crew autonomous operations. One of these focus areas is the development and execution of ISS Testbed for Analog Research (ISTAR) autonomous flight crew procedures intended to increase crew autonomy that will be required for long duration human exploration missions. Due to increasing communications delays and reduced logistics resupply, autonomous procedures are expected to help reduce crew reliance on the ground flight control team, increase crew performance, and enable the crew to become more subject-matter experts on both the exploration space vehicle systems and the scientific investigation operations that will be conducted on a long duration human space exploration mission. These tests make use of previous or ongoing projects tested in ground analogs such as Research and Technology Studies (RATS) and NASA Extreme Environment Mission Operations (NEEMO). Since the latter half of 2012, selected non-critical ISS systems crew procedures have been used to develop techniques for building ISTAR autonomous procedures, and ISS flight crews have successfully executed them without flight controller involvement. Although the main focus has been preparing for exploration, the ISS has been a beneficiary of this synergistic effort and is considering modifying additional standard ISS procedures that may increase crew efficiency, reduce operational costs, and

MANAGING UNCERTAINTIES ASSOCIATED WITH RADIOACTIVE WASTE DISPOSAL: TASK GROUP 4 OF THE IAEA PRISM PROJECT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seitz, R.

2011-03-02

It is widely recognized that the results of safety assessment calculations provide an important contribution to the safety arguments for a disposal facility, but cannot in themselves adequately demonstrate the safety of the disposal system. The safety assessment and a broader range of arguments and activities need to be considered holistically to justify radioactive waste disposal at any particular site. Many programs are therefore moving towards the production of what has become known as a Safety Case, which includes all of the different activities that are conducted to demonstrate the safety of a disposal concept. Recognizing the growing interest inmore » the concept of a Safety Case, the International Atomic Energy Agency (IAEA) is undertaking an intercomparison and harmonization project called PRISM (Practical Illustration and use of the Safety Case Concept in the Management of Near-surface Disposal). The PRISM project is organized into four Task Groups that address key aspects of the Safety Case concept: Task Group 1 - Understanding the Safety Case; Task Group 2 - Disposal facility design; Task Group 3 - Managing waste acceptance; and Task Group 4 - Managing uncertainty. This paper addresses the work of Task Group 4, which is investigating approaches for managing the uncertainties associated with near-surface disposal of radioactive waste and their consideration in the context of the Safety Case. Emphasis is placed on identifying a wide variety of approaches that can and have been used to manage different types of uncertainties, especially non-quantitative approaches that have not received as much attention in previous IAEA projects. This paper includes discussions of the current results of work on the task on managing uncertainty, including: the different circumstances being considered, the sources/types of uncertainties being addressed and some initial proposals for approaches that can be used to manage different types of uncertainties.« less

The development of an automatically produced cholangiography procedure using the reconstruction of portal-phase multidetector-row computed tomography images: preliminary experience.

PubMed

Hirose, Tomoaki; Igami, Tsuyoshi; Koga, Kusuto; Hayashi, Yuichiro; Ebata, Tomoki; Yokoyama, Yukihiro; Sugawara, Gen; Mizuno, Takashi; Yamaguchi, Junpei; Mori, Kensaku; Nagino, Masato

2017-03-01

Fusion angiography using reconstructed multidetector-row computed tomography (MDCT) images, and cholangiography using reconstructed images from MDCT with a cholangiographic agent include an anatomical gap due to the different periods of MDCT scanning. To conquer such gaps, we attempted to develop a cholangiography procedure that automatically reconstructs a cholangiogram from portal-phase MDCT images. The automatically produced cholangiography procedure utilized an original software program that was developed by the Graduate School of Information Science, Nagoya University. This program structured 5 candidate biliary tracts, and automatically selected one as the candidate for cholangiography. The clinical value of the automatically produced cholangiography procedure was estimated based on a comparison with manually produced cholangiography. Automatically produced cholangiograms were reconstructed for 20 patients who underwent MDCT scanning before biliary drainage for distal biliary obstruction. The procedure showed the ability to extract the 5 main biliary branches and the 21 subsegmental biliary branches in 55 and 25 % of the cases, respectively. The extent of aberrant connections and aberrant extractions outside the biliary tract was acceptable. Among all of the cholangiograms, 5 were clinically applied with no correction, 8 were applied with modest improvements, and 3 produced a correct cholangiography before automatic selection. Although our procedure requires further improvement based on the analysis of additional patient data, it may represent an alternative to direct cholangiography in the future.

Stuck fermentation: development of a synthetic stuck wine and study of a restart procedure.

PubMed

Maisonnave, Pierre; Sanchez, Isabelle; Moine, Virginie; Dequin, Sylvie; Galeote, Virginie

2013-05-15

Stuck fermentation is a major problem in winemaking, resulting in large losses in the wine industry. Specific starter yeasts are used to restart stuck fermentations in conditions determined essentially on the basis of empirical know-how. We have developed a model synthetic stuck wine and an industrial process-based procedure for restarting fermentations, for studies of the conditions required to restart stuck fermentations. We used a basic medium containing 13.5% v/v ethanol and 16 g/L fructose, pH 3.3, to test the effect of various nutrients (vitamins, amino acids, minerals, oligoelements), with the aim of developing a representative and discriminative stuck fermentation model. Cell growth appeared to be a key factor for the efficient restarting of stuck fermentations. Micronutrients, such as vitamins, also strongly affected the efficiency of the restart procedure. For the validation of this medium, we compared the performances of three wine yeast strains in the synthetic stuck fermentation and three naturally stuck wine fermentations. Strain performance was ranked similar in the synthetic medium and in the "Malbec" and "Sauvignon" natural stuck wines. However, two strains were ranked differently in the "Gros Manseng" stuck wine. Nutrient content seemed to be a crucial factor in fermentation restart conditions, generating differences between yeast strains. However, the specific sensitivity of yeast strains to the composition of the wine may also have had an effect. Copyright © 2013 Elsevier B.V. All rights reserved.

Comparison of AAPM Addendum to TG-51, IAEA TRS-398, and JSMP 12: Calibration of photon beams in water.

PubMed

Kinoshita, Naoki; Oguchi, Hiroshi; Nishimoto, Yasuhiro; Adachi, Toshiki; Shioura, Hiroki; Kimura, Hirohiko; Doi, Kunio

2017-09-01

The American Association of Physicists in Medicine (AAPM) Working Group on TG-51 published an Addendum to the AAPM's TG-51 protocol (Addendum to TG-51) in 2014, and the Japan Society of Medical Physics (JSMP) published a new dosimetry protocol JSMP 12 in 2012. In this study, we compared the absorbed dose to water determined at the reference depth for high-energy photon beams following the recommendations given in AAPM TG-51 and the Addendum to TG-51, IAEA TRS-398, and JSMP 12. This study was performed using measurements with flattened photon beams with nominal energies of 6 and 10 MV. Three widely used ionization chambers with different compositions, Exradin A12, PTW 30013, and IBA FC65-P, were employed. Fully corrected charge readings obtained for the three chambers according to AAPM TG-51 and the Addendum to TG-51, which included the correction for the radiation beam profile (P rp ), showed variations of 0.2% and 0.3% at 6 and 10 MV, respectively, from the readings corresponding to IAEA TRS-398 and JSMP 12. The values for the beam quality conversion factor k Q obtained according to the three protocols agreed within 0.5%; the only exception was a 0.6% difference between the results obtained at 10 MV for Exradin A12 according to IAEA TRS-398 and AAPM TG-51 and the Addendum to TG-51. Consequently, the values for the absorbed dose to water obtained for the three protocols agreed within 0.4%; the only exception was a 0.6% difference between the values obtained at 10 MV for PTW 30013 according to AAPM TG-51 and the Addendum to TG-51, and JSMP 12. While the difference in the absorbed dose to water determined by the three protocols depends on the k Q and P rp values, the absorbed dose to water obtained according to the three protocols agrees within the relative uncertainties for the three protocols. © 2017 The Authors. Journal of Applied Clinical Medical Physics published by Wiley Periodicals, Inc. on behalf of American Association of Physicists in Medicine.

Lessons Learned From Developing Reactor Pressure Vessel Steel Embrittlement Database

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Jy-An John

Materials behaviors caused by neutron irradiation under fission and/or fusion environments can be little understood without practical examination. Easily accessible material information system with large material database using effective computers is necessary for design of nuclear materials and analyses or simulations of the phenomena. The developed Embrittlement Data Base (EDB) at ORNL is this comprehensive collection of data. EDB database contains power reactor pressure vessel surveillance data, the material test reactor data, foreign reactor data (through bilateral agreements authorized by NRC), and the fracture toughness data. The lessons learned from building EDB program and the associated database management activity regardingmore » Material Database Design Methodology, Architecture and the Embedded QA Protocol are described in this report. The development of IAEA International Database on Reactor Pressure Vessel Materials (IDRPVM) and the comparison of EDB database and IAEA IDRPVM database are provided in the report. The recommended database QA protocol and database infrastructure are also stated in the report.« less

An Actor-Oriented Transfer Perspective on High School Students' Development of the Use of Procedures to Solve Problems on Rate of Change

ERIC Educational Resources Information Center

Roorda, Gerrit; Vos, Pauline; Goedhart, Martin J.

2015-01-01

This article reports on a longitudinal observation study about students' development in their use of procedures to calculate instantaneous rate of change. Different procedures for solving tasks on rate of change are taught in mathematics and physics classes, and together they form a repertoire. Our study took an actor-oriented perspective, which…

Recent Developments in Assessment Procedures in England and Wales.

ERIC Educational Resources Information Center

Goldstein, Harvey; Nuttall, Desmond

Focusing on technical issues, this paper critiques proposed changes in assessment procedures at the further educational level (ages 16 through 18) in England and Wales. Major structural changes are taking place at this educational level, partly because of large scale youth unemployment. The two current examination systems for the final year of…

XML syntax for clinical laboratory procedure manuals.

PubMed

Saadawi, Gilan; Harrison, James H

2003-01-01

We have developed a document type description (DTD) in Extensable Markup Language (XML) for clinical laboratory procedures. Our XML syntax can adequately structure a variety of procedure types across different laboratories and is compatible with current procedure standards. The combination of this format with an XML content management system and appropriate style sheets will allow efficient procedure maintenance, distributed access, customized display and effective searching across a large body of test information.

Use of Data Libraries for IAEA Nuclear Security Assessment Methodologies (NUSAM) [section 5.4

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shull, D.; Lane, M.

2015-06-23

Data libraries are essential for the characterization of the facility and provide the documented input which enables the facility assessment results and subsequent conclusions. Data Libraries are historical, verifiable, quantified, and applicable collections of testing data on different types of barriers, sensors, cameras, procedures, and/or personnel. Data libraries are developed and maintained as part of any assessment program or process. Data is collected during the initial stages of facility characterization to aid in the model and/or simulation development process. Data library values may also be developed through the use of state testing centers and/or site resources by testing different typesmore » of barriers, sensors, cameras, procedures, and/or personnel. If no data exists, subject matter expert opinion and manufacturer's specifications/ testing values can be the basis for initially assigning values, but are generally less reliable and lack appropriate confidence measures. The use of existing data libraries that have been developed by a state testing organization reduces the assessment costs by establishing standard delay, detection and assessment values for use by multiple sites or facilities where common barriers and alarms systems exist.« less

Development and Validation of a Novel Robotic Procedure Specific Simulation Platform: Partial Nephrectomy.

PubMed

Hung, Andrew J; Shah, Swar H; Dalag, Leonard; Shin, Daniel; Gill, Inderbir S

2015-08-01

We developed a novel procedure specific simulation platform for robotic partial nephrectomy. In this study we prospectively evaluate its face, content, construct and concurrent validity. This hybrid platform features augmented reality and virtual reality. Augmented reality involves 3-dimensional robotic partial nephrectomy surgical videos overlaid with virtual instruments to teach surgical anatomy, technical skills and operative steps. Advanced technical skills are assessed with an embedded full virtual reality renorrhaphy task. Participants were classified as novice (no surgical training, 15), intermediate (less than 100 robotic cases, 13) or expert (100 or more robotic cases, 14) and prospectively assessed. Cohort performance was compared with the Kruskal-Wallis test (construct validity). Post-study questionnaire was used to assess the realism of simulation (face validity) and usefulness for training (content validity). Concurrent validity evaluated correlation between virtual reality renorrhaphy task and a live porcine robotic partial nephrectomy performance (Spearman's analysis). Experts rated the augmented reality content as realistic (median 8/10) and helpful for resident/fellow training (8.0-8.2/10). Experts rated the platform highly for teaching anatomy (9/10) and operative steps (8.5/10) but moderately for technical skills (7.5/10). Experts and intermediates outperformed novices (construct validity) in efficiency (p=0.0002) and accuracy (p=0.002). For virtual reality renorrhaphy, experts outperformed intermediates on GEARS metrics (p=0.002). Virtual reality renorrhaphy and in vivo porcine robotic partial nephrectomy performance correlated significantly (r=0.8, p <0.0001) (concurrent validity). This augmented reality simulation platform displayed face, content and construct validity. Performance in the procedure specific virtual reality task correlated highly with a porcine model (concurrent validity). Future efforts will integrate procedure specific

48 CFR 715.370 - Alternative source selection procedures.

Code of Federal Regulations, 2010 CFR

2010-10-01

... selection procedures. 715.370 Section 715.370 Federal Acquisition Regulations System AGENCY FOR INTERNATIONAL DEVELOPMENT CONTRACTING METHODS AND CONTRACT TYPES CONTRACTING BY NEGOTIATION Source Selection 715.370 Alternative source selection procedures. The following selection procedures may be used, when...

How to Write Effective Procedure Manuals.

ERIC Educational Resources Information Center

Wold, Geoffrey H.

1987-01-01

Describes six key guidelines for developing usable procedure manuals, including defining the audience; designing a standard format; preparing an outline; using a clear, concise writing style; testing the procedures; and "finalizing" the product with indices, glossaries, appendices, and section tabs. Well-written manuals can increase…

33 CFR 401.63 - Radio procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Radio procedures. 401.63 Section 401.63 Navigation and Navigable Waters SAINT LAWRENCE SEAWAY DEVELOPMENT CORPORATION, DEPARTMENT OF TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Radio Communications § 401.63 Radio procedures. Every...

Procedures to develop a computerized adaptive test to assess patient-reported physical functioning.

PubMed

McCabe, Erin; Gross, Douglas P; Bulut, Okan

2018-06-07

The purpose of this paper is to demonstrate the procedures to develop and implement a computerized adaptive patient-reported outcome (PRO) measure using secondary analysis of a dataset and items from fixed-format legacy measures. We conducted secondary analysis of a dataset of responses from 1429 persons with work-related lower extremity impairment. We calibrated three measures of physical functioning on the same metric, based on item response theory (IRT). We evaluated efficiency and measurement precision of various computerized adaptive test (CAT) designs using computer simulations. IRT and confirmatory factor analyses support combining the items from the three scales for a CAT item bank of 31 items. The item parameters for IRT were calculated using the generalized partial credit model. CAT simulations show that reducing the test length from the full 31 items to a maximum test length of 8 items, or 20 items is possible without a significant loss of information (95, 99% correlation with legacy measure scores). We demonstrated feasibility and efficiency of using CAT for PRO measurement of physical functioning. The procedures we outlined are straightforward, and can be applied to other PRO measures. Additionally, we have included all the information necessary to implement the CAT of physical functioning in the electronic supplementary material of this paper.

Towards developing standard operating procedures for pre-clinical testing in the mdx mouse model of Duchenne muscular dystrophy

PubMed Central

Grounds, Miranda D.; Radley, Hannah G.; Lynch, Gordon S.; Nagaraju, Kanneboyina; De Luca, Annamaria

2008-01-01

This review discusses various issues to consider when developing standard operating procedures for pre-clinical studies in the mdx mouse model of Duchenne muscular dystrophy (DMD). The review describes and evaluates a wide range of techniques used to measure parameters of muscle pathology in mdx mice and identifies some basic techniques that might comprise standardised approaches for evaluation. While the central aim is to provide a basis for the development of standardised procedures to evaluate efficacy of a drug or a therapeutic strategy, a further aim is to gain insight into pathophysiological mechanisms in order to identify other therapeutic targets. The desired outcome is to enable easier and more rigorous comparison of pre-clinical data from different laboratories around the world, in order to accelerate identification of the best pre-clinical therapies in the mdx mouse that will fast-track translation into effective clinical treatments for DMD. PMID:18499465

Standardized Procedure Content And Data Structure Based On Human Factors Requirements For Computer-Based Procedures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bly, Aaron; Oxstrand, Johanna; Le Blanc, Katya L

2015-02-01

Most activities that involve human interaction with systems in a nuclear power plant are guided by procedures. Traditionally, the use of procedures has been a paper-based process that supports safe operation of the nuclear power industry. However, the nuclear industry is constantly trying to find ways to decrease the human error rate, especially the human errors associated with procedure use. Advances in digital technology make computer-based procedures (CBPs) a valid option that provides further enhancement of safety by improving human performance related to procedure use. The transition from paper-based procedures (PBPs) to CBPs creates a need for a computer-based proceduremore » system (CBPS). A CBPS needs to have the ability to perform logical operations in order to adjust to the inputs received from either users or real time data from plant status databases. Without the ability for logical operations the procedure is just an electronic copy of the paper-based procedure. In order to provide the CBPS with the information it needs to display the procedure steps to the user, special care is needed in the format used to deliver all data and instructions to create the steps. The procedure should be broken down into basic elements and formatted in a standard method for the CBPS. One way to build the underlying data architecture is to use an Extensible Markup Language (XML) schema, which utilizes basic elements to build each step in the smart procedure. The attributes of each step will determine the type of functionality that the system will generate for that step. The CBPS will provide the context for the step to deliver referential information, request a decision, or accept input from the user. The XML schema needs to provide all data necessary for the system to accurately perform each step without the need for the procedure writer to reprogram the CBPS. The research team at the Idaho National Laboratory has developed a prototype CBPS for field workers as well as

10 CFR 75.8 - IAEA inspections.

Code of Federal Regulations, 2011 CFR

2011-01-01

... exports) or § 75.43(c) (pertaining to imports) at any place where nuclear material may be located; (3... nuclear material at key measurement points for material balance accounting are representative; (3) Verify... samples at key measurement points for material balance accounting are taken in accordance with procedures...

10 CFR 75.8 - IAEA inspections.

Code of Federal Regulations, 2010 CFR

2010-01-01

... inspection at a facility, to: (1) Examine records kept under § 75.21; (2) Observe that the measurements of nuclear material at key measurement points for material balance accounting are representative; (3) Verify... samples at key measurement points for material balance accounting are taken in accordance with procedures...

Chapter 8. Medical procedures. Recommendations and standard operating procedures for intensive care unit and hospital preparations for an influenza epidemic or mass disaster.

PubMed

Zimmerman, Janice L; Sprung, Charles L

2010-04-01

To provide recommendations and standard operating procedures for intensive care unit and hospital preparations for an influenza pandemic or mass disaster with a specific focus on ensuring that adequate resources are available and appropriate protocols are developed to safely perform procedures in patients with and without influenza illness. Based on a literature review and expert opinion, a Delphi process was used to define the essential topics including performing medical procedures. Key recommendations include: (1) specify high-risk procedures (aerosol generating-procedures); (2) determine if certain procedures will not be performed during a pandemic; (3) develop protocols for safe performance of high-risk procedures that include appropriateness, qualifications of personnel, site, personal protection equipment, safe technique and equipment needs; (4) ensure adequate training of personnel in high-risk procedures; (5) procedures should be performed at the bedside whenever possible; (6) ensure safe respiratory therapy practices to avoid aerosols; (7) provide safe respiratory equipment; and (8) determine criteria for cancelling and/or altering elective procedures. Judicious planning and adoption of protocols for safe performance of medical procedures are necessary to optimize outcomes during a pandemic.

Development of A Two-Stage Procedure for the Automatic Recognition of Dysfluencies in the Speech of Children Who Stutter: I. Psychometric Procedures Appropriate for Selection of Training Material for Lexical Dysfluency Classifiers

PubMed Central

Howell, Peter; Sackin, Stevie; Glenn, Kazan

2007-01-01

This program of work is intended to develop automatic recognition procedures to locate and assess stuttered dysfluencies. This and the following article together, develop and test recognizers for repetitions and prolongations. The automatic recognizers classify the speech in two stages: In the first, the speech is segmented and in the second the segments are categorized. The units that are segmented are words. Here assessments by human judges on the speech of 12 children who stutter are described using a corresponding procedure. The accuracy of word boundary placement across judges, categorization of the words as fluent, repetition or prolongation, and duration of the different fluency categories are reported. These measures allow reliable instances of repetitions and prolongations to be selected for training and assessing the recognizers in the subsequent paper. PMID:9328878

Developing and Trialling an independent, scalable and repeatable IT-benchmarking procedure for healthcare organisations.

PubMed

Liebe, J D; Hübner, U

2013-01-01

Continuous improvements of IT-performance in healthcare organisations require actionable performance indicators, regularly conducted, independent measurements and meaningful and scalable reference groups. Existing IT-benchmarking initiatives have focussed on the development of reliable and valid indicators, but less on the questions about how to implement an environment for conducting easily repeatable and scalable IT-benchmarks. This study aims at developing and trialling a procedure that meets the afore-mentioned requirements. We chose a well established, regularly conducted (inter-) national IT-survey of healthcare organisations (IT-Report Healthcare) as the environment and offered the participants of the 2011 survey (CIOs of hospitals) to enter a benchmark. The 61 structural and functional performance indicators covered among others the implementation status and integration of IT-systems and functions, global user satisfaction and the resources of the IT-department. Healthcare organisations were grouped by size and ownership. The benchmark results were made available electronically and feedback on the use of these results was requested after several months. Fifty-ninehospitals participated in the benchmarking. Reference groups consisted of up to 141 members depending on the number of beds (size) and the ownership (public vs. private). A total of 122 charts showing single indicator frequency views were sent to each participant. The evaluation showed that 94.1% of the CIOs who participated in the evaluation considered this benchmarking beneficial and reported that they would enter again. Based on the feedback of the participants we developed two additional views that provide a more consolidated picture. The results demonstrate that establishing an independent, easily repeatable and scalable IT-benchmarking procedure is possible and was deemed desirable. Based on these encouraging results a new benchmarking round which includes process indicators is currently

22 CFR 226.71 - Closeout procedures.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Closeout procedures. 226.71 Section 226.71 Foreign Relations AGENCY FOR INTERNATIONAL DEVELOPMENT ADMINISTRATION OF ASSISTANCE AWARDS TO U.S. NON-GOVERNMENTAL ORGANIZATIONS After-the-Award Requirements § 226.71 Closeout procedures. (a) Recipients shall...

36 CFR 908.32 - Review procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Review procedures. 908.32 Section 908.32 Parks, Forests, and Public Property PENNSYLVANIA AVENUE DEVELOPMENT CORPORATION POLICY AND PROCEDURES TO FACILITATE THE RETENTION OF DISPLACED BUSINESSES AND RESIDENTS IN THE PENNSYLVANIA AVENUE...

36 CFR 909.170 - Compliance procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 36 Parks, Forests, and Public Property 3 2011-07-01 2011-07-01 false Compliance procedures. 909... PENNSYLVANIA AVENUE DEVELOPMENT CORPORATION § 909.170 Compliance procedures. (a) Except as provided in... Barriers Compliance Board upon receipt of any complaint alleging that a building or facility that is...

45 CFR 98.66 - Disallowance procedures.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 45 Public Welfare 1 2014-10-01 2014-10-01 false Disallowance procedures. 98.66 Section 98.66 Public Welfare Department of Health and Human Services GENERAL ADMINISTRATION CHILD CARE AND DEVELOPMENT FUND Financial Management § 98.66 Disallowance procedures. (a) Any expenditures not made in accordance...

45 CFR 98.66 - Disallowance procedures.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 45 Public Welfare 1 2011-10-01 2011-10-01 false Disallowance procedures. 98.66 Section 98.66 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION CHILD CARE AND DEVELOPMENT FUND Financial Management § 98.66 Disallowance procedures. (a) Any expenditures not made in accordance...

45 CFR 98.66 - Disallowance procedures.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 45 Public Welfare 1 2010-10-01 2010-10-01 false Disallowance procedures. 98.66 Section 98.66 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION CHILD CARE AND DEVELOPMENT FUND Financial Management § 98.66 Disallowance procedures. (a) Any expenditures not made in accordance...

45 CFR 98.66 - Disallowance procedures.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 45 Public Welfare 1 2012-10-01 2012-10-01 false Disallowance procedures. 98.66 Section 98.66 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION CHILD CARE AND DEVELOPMENT FUND Financial Management § 98.66 Disallowance procedures. (a) Any expenditures not made in accordance...

45 CFR 98.66 - Disallowance procedures.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 45 Public Welfare 1 2013-10-01 2013-10-01 false Disallowance procedures. 98.66 Section 98.66 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION CHILD CARE AND DEVELOPMENT FUND Financial Management § 98.66 Disallowance procedures. (a) Any expenditures not made in accordance...

25 CFR 286.15 - Application procedures.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Application procedures. 286.15 Section 286.15 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ECONOMIC ENTERPRISES INDIAN BUSINESS DEVELOPMENT PROGRAM § 286.15 Application procedures. Applications are to be submitted to the Superintendent having...

30 CFR 402.15 - Reporting procedures.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 2 2013-07-01 2013-07-01 false Reporting procedures. 402.15 Section 402.15 Mineral Resources GEOLOGICAL SURVEY, DEPARTMENT OF THE INTERIOR WATER-RESOURCES RESEARCH PROGRAM AND THE WATER-RESOURCES TECHNOLOGY DEVELOPMENT PROGRAM Reporting § 402.15 Reporting procedures. (a) Grantees or...

30 CFR 402.15 - Reporting procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 2 2014-07-01 2014-07-01 false Reporting procedures. 402.15 Section 402.15 Mineral Resources GEOLOGICAL SURVEY, DEPARTMENT OF THE INTERIOR WATER-RESOURCES RESEARCH PROGRAM AND THE WATER-RESOURCES TECHNOLOGY DEVELOPMENT PROGRAM Reporting § 402.15 Reporting procedures. (a) Grantees or...

30 CFR 402.15 - Reporting procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 2 2012-07-01 2012-07-01 false Reporting procedures. 402.15 Section 402.15 Mineral Resources GEOLOGICAL SURVEY, DEPARTMENT OF THE INTERIOR WATER-RESOURCES RESEARCH PROGRAM AND THE WATER-RESOURCES TECHNOLOGY DEVELOPMENT PROGRAM Reporting § 402.15 Reporting procedures. (a) Grantees or...

30 CFR 402.15 - Reporting procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Reporting procedures. 402.15 Section 402.15 Mineral Resources GEOLOGICAL SURVEY, DEPARTMENT OF THE INTERIOR WATER-RESOURCES RESEARCH PROGRAM AND THE WATER-RESOURCES TECHNOLOGY DEVELOPMENT PROGRAM Reporting § 402.15 Reporting procedures. (a) Grantees or...

30 CFR 402.15 - Reporting procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 2 2011-07-01 2011-07-01 false Reporting procedures. 402.15 Section 402.15 Mineral Resources GEOLOGICAL SURVEY, DEPARTMENT OF THE INTERIOR WATER-RESOURCES RESEARCH PROGRAM AND THE WATER-RESOURCES TECHNOLOGY DEVELOPMENT PROGRAM Reporting § 402.15 Reporting procedures. (a) Grantees or...

Relations among Conceptual Knowledge, Procedural Knowledge, and Procedural Flexibility in Two Samples Differing in Prior Knowledge

ERIC Educational Resources Information Center

Schneider, Michael; Rittle-Johnson, Bethany; Star, Jon R.

2011-01-01

Competence in many domains rests on children developing conceptual and procedural knowledge, as well as procedural flexibility. However, research on the developmental relations between these different types of knowledge has yielded unclear results, in part because little attention has been paid to the validity of the measures or to the effects of…

Exploration of Terminal Procedures Enabled by NASA Wake VAS Technologies

NASA Technical Reports Server (NTRS)

Lunsford, Clark R.; Smith, Arthur P., III; Cooper, Wayne W., Jr.; Mundra, Anand D.; Gross, Amy E.; Audenaerd, Laurence F.; Killian, Bruce E.

2004-01-01

The National Aeronautics and Space Administration (NASA) tasked The MITRE Corporation's Center for Advanced Aviation System Development (CAASD) to investigate potential air traffic control (ATC) procedures that could benefit from technology used or developed in NASA's Wake Vortex Advisory System (WakeVAS). The task also required developing an estimate of the potential benefits of the candidate procedures. The main thrust of the investigation was to evaluate opportunities for improved capacity and efficiency in airport arrival and departure operations. Other procedures that would provide safety enhancements were also considered. The purpose of this investigation was to provide input to the WakeVAS program office regarding the most promising areas of development for the program. A two-fold perspective was desired: First, identification of benefits from possible procedures enabled by both incremental components and the mature state of WakeVAS technology; second identification of procedures that could be expected to evolve from the current Federal Aviation Administration (FAA) procedures. The evolution of procedures should provide meaningful increments of benefit and a low risk implementation of the WakeVAS technologies.

A simulator study for the development and evaluation of operating procedures on a supersonic cruise research transport to minimize airport-community noise

NASA Technical Reports Server (NTRS)

Grantham, W. D.; Smith, P. M.; Deal, P. L.

1980-01-01

Piloted-simulator studies were conducted to determine takeoff and landing operating procedures for a supersonic cruise research transport concept that result in predicted noise levels which meet current Federal Aviation Administration (FAA) certification standards. With the use of standard FAA noise certification test procedures, the subject simulated aircraft did not meet the FAA traded-noise-level standards during takeoff and landing. However, with the use of advanced procedures, this aircraft meets the traded-noise-level standards for flight crews with average skills. The advanced takeoff procedures developed involved violating some of the current Federal Aviation Regulations (FAR), but it was not necessary to violate any FAR noise-test conditions during landing approach. Noise contours were also determined for some of the simulated takeoffs and landings in order to indicate the noise-reduction advantages of using operational procedures other than standard.

On the acquisition and representation of procedural knowledge

NASA Technical Reports Server (NTRS)

Saito, T.; Ortiz, C.; Loftin, R. B.

1992-01-01

Historically knowledge acquisition has proven to be one of the greatest barriers to the development of intelligent systems. Current practice generally requires lengthy interactions between the expert whose knowledge is to be captured and the knowledge engineer whose responsibility is to acquire and represent knowledge in a useful form. Although much research has been devoted to the development of methodologies and computer software to aid in the capture and representation of some of some types of knowledge, little attention has been devoted to procedural knowledge. NASA personnel frequently perform tasks that are primarily procedural in nature. Previous work is reviewed in the field of knowledge acquisition and then focus on knowledge acquisition for procedural tasks with special attention devoted to the Navy's VISTA tool. The design and development is described of a system for the acquisition and representation of procedural knowledge-TARGET (Task Analysis and Rule Generation Tool). TARGET is intended as a tool that permits experts to visually describe procedural tasks and as a common medium for knowledge refinement by the expert and knowledge engineer. The system is designed to represent the acquired knowledge in the form of production rules. Systems such as TARGET have the potential to profoundly reduce the time, difficulties, and costs of developing knowledge-based systems for the performance of procedural tasks.

Alternative antimicrobial commercial egg washing procedures

USDA-ARS?s Scientific Manuscript database

Commercial table eggs are washed prior to packaging. Standard wash procedures use an alkaline pH and warm water. If a cool water method could be developed that would still provide a microbiologically safe egg, the industry may save energy costs associated with water heating. Four wash procedures ...

The NASA Constellation Program Procedure System

NASA Technical Reports Server (NTRS)

Phillips, Robert G.; Wang, Lui

2010-01-01

NASA has used procedures to describe activities to be performed onboard vehicles by astronaut crew and on the ground by flight controllers since Apollo. Starting with later Space Shuttle missions and the International Space Station, NASA moved forward to electronic presentation of procedures. For the Constellation Program, another large step forward is being taken - to make procedures more interactive with the vehicle and to assist the crew in controlling the vehicle more efficiently and with less error. The overall name for the project is the Constellation Procedure Applications Software System (CxPASS). This paper describes some of the history behind this effort, the key concepts and operational paradigms that the work is based upon, and the actual products being developed to implement procedures for Constellation

Development of improved pavement rehabilitation procedures based on FWD backcalculation.

DOT National Transportation Integrated Search

2015-01-01

Hot Mix Asphalt (HMA) overlays are among the most effective maintenance and rehabilitation : alternatives in improving the structural as well as functional performance of flexible pavements. HMA : overlay design procedures can be based on: (1) engine...

76 FR 27016 - Evaluating Test Procedures for Voting Systems

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-10

...-02] Evaluating Test Procedures for Voting Systems AGENCY: National Institute of Standards and... Assistance Commission for use by NIST in research to develop and assess NIST's test procedures for voting... develop and assess NIST test protocols for voting equipment. NIST research is designed to: (1) Develop...

Development of intra-strain self-cloning procedure for breeding baker's yeast strains.

PubMed

Nakagawa, Youji; Ogihara, Hiroyuki; Mochizuki, Chisato; Yamamura, Hideki; Iimura, Yuzuru; Hayakawa, Masayuki

2017-03-01

Previously reported self-cloning procedures for breeding of industrial yeast strains require DNA from other strains, plasmid DNA, or mutagenesis. Therefore, we aimed to construct a self-cloning baker's yeast strain that exhibits freeze tolerance via an improved self-cloning procedure. We first disrupted the URA3 gene of a prototrophic baker's yeast strain without the use of any marker gene, resulting in a Δura3 homozygous disruptant. Then, the URA3 gene of the parental baker's yeast strain was used as a selection marker to introduce the constitutive TDH3 promoter upstream of the PDE2 gene encoding high-affinity cyclic AMP phosphodiesterase. This self-cloning procedure was performed without using DNA from other Saccharomyces cerevisiae strains, plasmid DNA, or mutagenesis and was therefore designated an intra-strain self-cloning procedure. Using this self-cloning procedure, we succeeded in producing self-cloning baker's yeast strains that harbor the TDH3p-PDE2 gene heterozygously and homozygously, designated TDH3p-PDE2 hetero and TDH3p-PDE2 homo strains, respectively. These self-cloning strains expressed much higher levels of PDE2 mRNA than the parental strain and exhibited higher viability after freeze stress, as well as higher fermentation ability in frozen dough, when compared with the parental strain. The TDH3p-PDE2 homo strain was genetically more stable than the TDH3p-PDE2 hetero strain. These results indicate that both heterozygous and homozygous strains of self-cloning PDE2-overexpressing freeze-tolerant strains of industrial baker's yeast can be prepared using the intra-strain self-cloning procedure, and, from a practical viewpoint, the TDH3p-PDE2 homo strain constructed in this study is preferable to the TDH3p-PDE2 hetero strain for frozen dough baking. Copyright © 2016 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

24 CFR 574.510 - Environmental procedures and standards.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 3 2011-04-01 2010-04-01 true Environmental procedures and standards. 574.510 Section 574.510 Housing and Urban Development Regulations Relating to Housing and Urban... Administration § 574.510 Environmental procedures and standards. (a) Activities under this part are subject to...

Development of a multiple-parameter nonlinear perturbation procedure for transonic turbomachinery flows: Preliminary application to design/optimization problems

NASA Technical Reports Server (NTRS)

Stahara, S. S.; Elliott, J. P.; Spreiter, J. R.

1983-01-01

An investigation was conducted to continue the development of perturbation procedures and associated computational codes for rapidly determining approximations to nonlinear flow solutions, with the purpose of establishing a method for minimizing computational requirements associated with parametric design studies of transonic flows in turbomachines. The results reported here concern the extension of the previously developed successful method for single parameter perturbations to simultaneous multiple-parameter perturbations, and the preliminary application of the multiple-parameter procedure in combination with an optimization method to blade design/optimization problem. In order to provide as severe a test as possible of the method, attention is focused in particular on transonic flows which are highly supercritical. Flows past both isolated blades and compressor cascades, involving simultaneous changes in both flow and geometric parameters, are considered. Comparisons with the corresponding exact nonlinear solutions display remarkable accuracy and range of validity, in direct correspondence with previous results for single-parameter perturbations.

Fusion Imaging for Procedural Guidance.

PubMed

Wiley, Brandon M; Eleid, Mackram F; Thaden, Jeremy J

2018-05-01

The field of percutaneous structural heart interventions has grown tremendously in recent years. This growth has fueled the development of new imaging protocols and technologies in parallel to help facilitate these minimally-invasive procedures. Fusion imaging is an exciting new technology that combines the strength of 2 imaging modalities and has the potential to improve procedural planning and the safety of many commonly performed transcatheter procedures. In this review we discuss the basic concepts of fusion imaging along with the relative strengths and weaknesses of static vs dynamic fusion imaging modalities. This review will focus primarily on echocardiographic-fluoroscopic fusion imaging and its application in commonly performed transcatheter structural heart procedures. Copyright © 2017 Sociedad Española de Cardiología. Published by Elsevier España, S.L.U. All rights reserved.

Situation analysis of the National Comprehensive Cancer Control Program (2013) in the I. R. of Iran; assessment and recommendations based on the IAEA imPACT mission.

PubMed

Rouhollahi, Mohammad Reza; Mohagheghi, Mohammad Ali; Mohammadrezai, Narges; Ghiasvand, Reza; Ghanbari Motlagh, Ali; Harirchi, Iraj; Zendehdel, Kazem

2014-04-01

Iran was engaged in the Program of Action for Cancer Therapy (PACT) in 2012, and delegates from the International Atomic Energy Agency (IAEA), and the World Health Organization (WHO) evaluated the National Cancer Control Program (NCCP) status (the imPACT mission), based on which they provided recommendations for improvements of NCCP in the I.R. of Iran. We reported the results of this situational analysis and discussed the recommendations and their implication in the promotion of NCCP in the I.R. of Iran.  International delegates visited the I.R. of Iran and evaluated different aspects and capacities of NCCP in Iran. In addition, a Farsi version of the WHO/IAEA self-assessment tool was completed by local experts and stakeholders, including experts from different departments of the Ministry of Health and Medical Education (MOHME) and representatives from the National Cancer Research Network (NCRN). Following these evaluations, the PACT office provided recommendations for improving the NCCP in Iran. Almost all the recommendations were endorsed by MOHME. The PACT program provided 31 recommendations for improvement of NCCP in Iran in six categories, including planning, cancer registration and information, prevention, early detection, diagnosis and treatment, and palliative care. The most important recommendation was to establish a strong, multi-sectoral NCCP committee and develop an updated national cancer control program. The imPACT mission report provided a comprehensive view about the NCCP status in Iran. An appropriate response to these recommendations and filing the observed gaps will improve the NCCP status in the I.R. of Iran.

The use of high-fidelity human patient simulation as an evaluative tool in the development of clinical research protocols and procedures.

PubMed

Wright, Melanie C; Taekman, Jeffrey M; Barber, Linda; Hobbs, Gene; Newman, Mark F; Stafford-Smith, Mark

2005-12-01

Errors in clinical research can be costly, in terms of patient safety, data integrity, and data collection. Data inaccuracy in early subjects of a clinical study may be associated with problems in the design of the protocol, procedures, and data collection tools. High-fidelity patient simulation centers provide an ideal environment to apply human-centered design to clinical trial development. A draft of a complex clinical protocol was designed, evaluated and modified using a high-fidelity human patient simulator in the Duke University Human Simulation and Patient Safety Center. The process included walk-throughs, detailed modifications of the protocol and development of procedural aids. Training of monitors and coordinators provided an opportunity for observation of performance that was used to identify further improvements to the protocol. Evaluative steps were used to design the research protocol and procedures. Iterative modifications were made to the protocol and data collection tools. The success in use of human simulation in the preparation of a complex clinical drug trial suggests the benefits of human patient simulation extend beyond training and medical equipment evaluation. Human patient simulation can provide a context for informal expert evaluation of clinical protocol design and for formal "rehearsal" to evaluate the efficacy of procedures and support tools.

13 CFR 130.400 - Application procedure. [Reserved

Code of Federal Regulations, 2011 CFR

2011-01-01

... 13 Business Credit and Assistance 1 2011-01-01 2011-01-01 false Application procedure. [Reserved] 130.400 Section 130.400 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION SMALL BUSINESS DEVELOPMENT CENTERS § 130.400 Application procedure. [Reserved] ...

13 CFR 130.400 - Application procedure. [Reserved

Code of Federal Regulations, 2010 CFR

2010-01-01

... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Application procedure. [Reserved] 130.400 Section 130.400 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION SMALL BUSINESS DEVELOPMENT CENTERS § 130.400 Application procedure. [Reserved] ...

Developing Flowcharted Procedures Manuals for School District Administration within the ISO 9000 Context.

ERIC Educational Resources Information Center

Schoch, Robert

2002-01-01

Describes how the School District of Lancaster, Pennsylvania, implemented a districtwide quality-management system based on the Geneva-based International Standards Organization 9001, a major component of which is the documentation of procedures. Includes sections on implementation, procedure manuals, quality management, uniformity, formatting,…

Army Blast Claims Evaluation Procedures

DTIC Science & Technology

1994-03-01

ARMY RESEARCH LABORATORY ARL-MR-131 Army Blast Claims Evaluation Procedures William P. Wright APPROVED FOR PUBUC RELEASE; DISTRIBtmON IS...NUMBERS Anny Blast Claims Evaluation Procedures 4G061-304-U2 6. AUTHOR(S) William P. Wrisht 1. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) 8...of the technical review process which bas been instituted to develop an opinion as to Army responsibility. 14. SUBJECT TERMS blast effects. muzzle

Spacecraft crew procedures from paper to computers

NASA Technical Reports Server (NTRS)

Oneal, Michael; Manahan, Meera

1991-01-01

Described here is a research project that uses human factors and computer systems knowledge to explore and help guide the design and creation of an effective Human-Computer Interface (HCI) for spacecraft crew procedures. By having a computer system behind the user interface, it is possible to have increased procedure automation, related system monitoring, and personalized annotation and help facilities. The research project includes the development of computer-based procedure system HCI prototypes and a testbed for experiments that measure the effectiveness of HCI alternatives in order to make design recommendations. The testbed will include a system for procedure authoring, editing, training, and execution. Progress on developing HCI prototypes for a middeck experiment performed on Space Shuttle Mission STS-34 and for upcoming medical experiments are discussed. The status of the experimental testbed is also discussed.

Development of the Quality Assurance/Quality Control Procedures for a Neutron Interrogation System

NASA Astrophysics Data System (ADS)

Obhođaš, Jasmina; Sudac, Davorin; Valković, Vladivoj

2016-06-01

In order to perform Quality Assurance/Quality Control (QA/QC) procedures for a system dedicated to the neutron interrogation of objects for the presence of threat materials one needs to perform measurements of reference materials (RM) i.e. simulants having the same (or similar) atomic ratios as real materials. It is well known that explosives, drugs, and various other benign materials, contain chemical elements such as hydrogen, oxygen, carbon and nitrogen in distinctly different quantities. For example, a high carbon-to-oxygen ratio (C/O) is characteristic of drugs. Explosives can be differentiated by measurement of both (C/O) and nitrogen-to-oxygen (N/O) ratios. The C/N ratio of the chemical warfare agents, coupled with the measurement of elements such as fluorine and phosphorus, clearly differentiate them from the conventional explosives. Here we present the RM preparation, calibration procedure and correlations attained between theoretical values and experimentally obtained results in laboratory conditions for C/O and N/C ratios of prepared hexogen (RDX), TNT, DLM2, TATP, cocaine, heroin, yperite, tetranitromethane, peroxide methylethylketone, nitromethane and ethyleneglycol dinitrate simulants. We have shown that analyses of the gamma ray spectra by using simple unfolding model developed for this purpose gave a nice agreement with the chemical formula of created simulants, thus the calibration quality was successfully tested.

Development of a drift-correction procedure for a direct-reading spectrometer

NASA Technical Reports Server (NTRS)

Chapman, G. B., II; Gordon, W. A.

1977-01-01

A procedure which provides automatic correction for drifts in the radiometric sensitivity of each detector channel in a direct-reading emission spectrometer is described. Such drifts are customarily controlled by the regular analyses of standards, which provide corrections for changes in the excitational, optical, and electronic components of the instrument. This standardization procedure, however, corrects for the optical and electronic drifts. It is a step that must be taken if the time, effort, and cost of processing standards is to be minimized. This method of radiometric drift correction uses a 1,000-W tungsten-halogen reference lamp to illuminate each detector through the same optical path as that traversed during sample analysis. The responses of the detector channels to this reference light are regularly compared with channel response to the same light intensity at the time of analytical calibration in order to determine and correct for drift. Except for placing the lamp in position, the procedure is fully automated and compensates for changes in spectral intensity due to variations in lamp current. A discussion of the implementation of this drift-correction system is included.

Treatment of control data in lunar phototriangulation. [application of statistical procedures and development of mathematical and computer techniques

NASA Technical Reports Server (NTRS)

Wong, K. W.

1974-01-01

In lunar phototriangulation, there is a complete lack of accurate ground control points. The accuracy analysis of the results of lunar phototriangulation must, therefore, be completely dependent on statistical procedure. It was the objective of this investigation to examine the validity of the commonly used statistical procedures, and to develop both mathematical techniques and computer softwares for evaluating (1) the accuracy of lunar phototriangulation; (2) the contribution of the different types of photo support data on the accuracy of lunar phototriangulation; (3) accuracy of absolute orientation as a function of the accuracy and distribution of both the ground and model points; and (4) the relative slope accuracy between any triangulated pass points.

PDSS configuration control plan and procedures

NASA Technical Reports Server (NTRS)

1983-01-01

The payload development support system (PDSS) configuration control plan and procedures are presented. These plans and procedures establish the process for maintaining configuration control of the PDSS system, especially the Spacelab experiment interface device's (SEID) RAU, HRM, and PDI interface simulations and the PDSS ECOS DEP Services simulation. The plans and procedures as specified are designed to provide a simplified but complete configuration control process. The intent is to require a minimum amount of paperwork but provide total traceability of PDSS during experiment test activities.

Developments in Assisting Countries in Implementing the IAEA Additional Protocol

DOE Office of Scientific and Technical Information (OSTI.GOV)

Killinger, Mark H.; Hansen, Linda H.; Cain, Ronald A.

In 2008, the U.S. Department of Energy (DOE) began assisting selected non-nuclear weapon states in planning and preparing for implementation of the International Atomic Energy Agency’s Additional Protocol (AP). Since then, the AP international implementation program has contributed to the substantial progress made by Vietnam, Thailand, Iraq, and Malaysia in preparing for entry-into-force of the AP. An overall engagement plan has been developed with components designed to train government AP implementing agencies, inform policy makers, conduct outreach to industry and universities, make AP reporting software available and useful, and plan a detailed approach for implementing the declaration and complementary accessmore » provisions of the AP. DOE recently began collaborating with Indonesia, which has already entered the AP into force, requiring a second method of engagement somewhat different from that taken with countries that have not entered the AP into force. The AP international implementation program, administered by the International Nuclear Safeguards and Engagement Program, is working more closely with DOE’s International Nonproliferation Export Control Program to ensure countries are aware of and prepared to implement the export/import provisions of the AP. As the AP implementation program matures and helps move countries closer to entry-into-force or improved AP implementation, it is identifying characteristics of a country’s “end-state” that indicate that DOE assistance is no longer required. The U.S. AP Implementation Act and Senate Resolution of Ratification require the Administration to report annually to Congress on measures taken to achieve the adoption of the AP in non-nuclear weapon states. DOE’s AP international implementation program is a significant part of these measures. This paper describes recent developments to increase the scope and effectiveness of the program.« less

Development of a new calibration procedure and its experimental validation applied to a human motion capture system.

PubMed

Royo Sánchez, Ana Cristina; Aguilar Martín, Juan José; Santolaria Mazo, Jorge

2014-12-01

Motion capture systems are often used for checking and analyzing human motion in biomechanical applications. It is important, in this context, that the systems provide the best possible accuracy. Among existing capture systems, optical systems are those with the highest accuracy. In this paper, the development of a new calibration procedure for optical human motion capture systems is presented. The performance and effectiveness of that new calibration procedure are also checked by experimental validation. The new calibration procedure consists of two stages. In the first stage, initial estimators of intrinsic and extrinsic parameters are sought. The camera calibration method used in this stage is the one proposed by Tsai. These parameters are determined from the camera characteristics, the spatial position of the camera, and the center of the capture volume. In the second stage, a simultaneous nonlinear optimization of all parameters is performed to identify the optimal values, which minimize the objective function. The objective function, in this case, minimizes two errors. The first error is the distance error between two markers placed in a wand. The second error is the error of position and orientation of the retroreflective markers of a static calibration object. The real co-ordinates of the two objects are calibrated in a co-ordinate measuring machine (CMM). The OrthoBio system is used to validate the new calibration procedure. Results are 90% lower than those from the previous calibration software and broadly comparable with results from a similarly configured Vicon system.

Safeguards Technology Development Program 1st Quarter FY 2018 Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prasad, Manoj K.

LLNL will evaluate the performance of a stilbene-based scintillation detector array for IAEA neutron multiplicity counting (NMC) applications. This effort will combine newly developed modeling methodologies and recently acquired high-efficiency stilbene detector units to quantitatively compare the prototype system performance with the conventional He-3 counters and liquid scintillator alternatives.

24 CFR 115.205 - Certification procedures.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 1 2011-04-01 2011-04-01 false Certification procedures. 115.205 Section 115.205 Housing and Urban Development Regulations Relating to Housing and Urban Development OFFICE OF ASSISTANT SECRETARY FOR EQUAL OPPORTUNITY, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT FAIR...

24 CFR 115.205 - Certification procedures.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 1 2012-04-01 2012-04-01 false Certification procedures. 115.205 Section 115.205 Housing and Urban Development Regulations Relating to Housing and Urban Development OFFICE OF ASSISTANT SECRETARY FOR EQUAL OPPORTUNITY, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT FAIR...

24 CFR 115.205 - Certification procedures.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 1 2013-04-01 2013-04-01 false Certification procedures. 115.205 Section 115.205 Housing and Urban Development Regulations Relating to Housing and Urban Development OFFICE OF ASSISTANT SECRETARY FOR EQUAL OPPORTUNITY, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT FAIR...

24 CFR 115.205 - Certification procedures.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 24 Housing and Urban Development 1 2014-04-01 2014-04-01 false Certification procedures. 115.205 Section 115.205 Housing and Urban Development Regulations Relating to Housing and Urban Development OFFICE OF ASSISTANT SECRETARY FOR EQUAL OPPORTUNITY, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT FAIR...

Development of an Analytical Procedure for the Determination of Multiclass Compounds for Forensic Veterinary Toxicology.

PubMed

Sell, Bartosz; Sniegocki, Tomasz; Zmudzki, Jan; Posyniak, Andrzej

2018-04-01

Reported here is a new analytical multiclass method based on QuEChERS technique, which has proven to be effective in diagnosing fatal poisoning cases in animals. This method has been developed for the determination of analytes in liver samples comprising rodenticides, carbamate and organophosphorus pesticides, coccidiostats and mycotoxins. The procedure entails addition of acetonitrile and sodium acetate to 2 g of homogenized liver sample. The mixture was shaken intensively and centrifuged for phase separation, which was followed by an organic phase transfer into a tube containing sorbents (PSA and C18) and magnesium sulfate, then it was centrifuged, the supernatant was filtered and analyzed by liquid chromatography tandem mass spectrometry. A validation of the procedure was performed. Repeatability variation coefficients <15% have been achieved for most of the analyzed substances. Analytical conditions allowed for a successful separation of variety of poisons with the typical screening detection limit at ≤10 μg/kg levels. The method was used to investigate more than 100 animals poisoning incidents and proved that is useful to be used in animal forensic toxicology cases.

Therapeutic applications of radioactive (131)iodine: Procedures and incidents with capsules.

PubMed

Al Aamri, Marwa; Ravichandran, Ramamoorthy; Binukumar, John Pichy; Al Balushi, Naima

2016-01-01

Treatments for thyrotoxicosis and carcinoma thyroid are carried out by oral administration of radioactive iodine ((131)I) in the form of liquid or capsules. The liquid form of (131)I has higher risk factors such as vapourization, spillage and need for management of higher activity wastes. Use of (131)I in capsule form simplify procedures of handling compared to liquid form of (131)I. The guidelines of safe handling and quality assurance aspects for therapeutic use (131)I are well outlined by International Atomic Energy Agency (IAEA) reports. A few unusual incidents with I-131 capsules encountered in the past need to be highlighted from health physics point of view. In Royal Hospital, Oman, I-131 is imported in capsules, and the total activity handled/year steadily increased over 10 years. Discrete activities range from 185 MBq (5 mCi) up to 7.4 GBq (200 mCi). In four incidents deviations in standard operational procedures were recorded. Nature of incidents is described as follows: (1) After assay of activity, the capsule was directly put in the lead container with missing of inner cap. (2) Patient poured water in the Perspex tube, when the capsule was handed over to her, making an emergency situation. (3) In 3 high activity capsules (2 nos 2.96 GBq, 1 no. 4.26 GBq), observed sticky behavior in capsule holder on the 2(nd) day post receipt, which were in order on the 1(st) day. (4) A capsule could not be swallowed by a patient, which was taken back from the mouth. Monitoring of patient later did not show residual ingested activity. The report documents some of the unusual incidents for information to other centers engaged in such radioactive administrations.

24 CFR 246.10 - HUD procedures.

Code of Federal Regulations, 2010 CFR

2010-04-01

... DEVELOPMENT MORTGAGE AND LOAN INSURANCE PROGRAMS UNDER NATIONAL HOUSING ACT AND OTHER AUTHORITIES LOCAL RENT... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false HUD procedures. 246.10 Section 246.10 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued...

24 CFR 246.10 - HUD procedures.

Code of Federal Regulations, 2011 CFR

2011-04-01

... DEVELOPMENT MORTGAGE AND LOAN INSURANCE PROGRAMS UNDER NATIONAL HOUSING ACT AND OTHER AUTHORITIES LOCAL RENT... 24 Housing and Urban Development 2 2011-04-01 2011-04-01 false HUD procedures. 246.10 Section 246.10 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued...

24 CFR 246.10 - HUD procedures.

Code of Federal Regulations, 2012 CFR

2012-04-01

... DEVELOPMENT MORTGAGE AND LOAN INSURANCE PROGRAMS UNDER NATIONAL HOUSING ACT AND OTHER AUTHORITIES LOCAL RENT... 24 Housing and Urban Development 2 2012-04-01 2012-04-01 false HUD procedures. 246.10 Section 246.10 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued...

24 CFR 246.10 - HUD procedures.

Code of Federal Regulations, 2013 CFR

2013-04-01

... DEVELOPMENT MORTGAGE AND LOAN INSURANCE PROGRAMS UNDER NATIONAL HOUSING ACT AND OTHER AUTHORITIES LOCAL RENT... 24 Housing and Urban Development 2 2013-04-01 2013-04-01 false HUD procedures. 246.10 Section 246.10 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued...

24 CFR 246.10 - HUD procedures.

Code of Federal Regulations, 2014 CFR

2014-04-01

... DEVELOPMENT MORTGAGE AND LOAN INSURANCE PROGRAMS UNDER NATIONAL HOUSING ACT AND OTHER AUTHORITIES LOCAL RENT... 24 Housing and Urban Development 2 2014-04-01 2014-04-01 false HUD procedures. 246.10 Section 246.10 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued...

Middle-ear microsurgery simulation to improve new robotic procedures.

PubMed

Kazmitcheff, Guillaume; Nguyen, Yann; Miroir, Mathieu; Péan, Fabien; Ferrary, Evelyne; Cotin, Stéphane; Sterkers, Olivier; Duriez, Christian

2014-01-01

Otological microsurgery is delicate and requires high dexterity in bad ergonomic conditions. To assist surgeons in these indications, a teleoperated system, called RobOtol, is developed. This robot enhances gesture accuracy and handiness and allows exploration of new procedures for middle ear surgery. To plan new procedures that exploit the capacities given by the robot, a surgical simulator is developed. The simulation reproduces with high fidelity the behavior of the anatomical structures and can also be used as a training tool for an easier control of the robot for surgeons. In the paper, we introduce the middle ear surgical simulation and then we perform virtually two challenging procedures with the robot. We show how interactive simulation can assist in analyzing the benefits of robotics in the case of complex manipulations or ergonomics studies and allow the development of innovative surgical procedures. New robot-based microsurgical procedures are investigated. The improvement offered by RobOtol is also evaluated and discussed.

Middle-Ear Microsurgery Simulation to Improve New Robotic Procedures

PubMed Central

Kazmitcheff, Guillaume; Nguyen, Yann; Miroir, Mathieu; Péan, Fabien; Ferrary, Evelyne; Cotin, Stéphane; Sterkers, Olivier; Duriez, Christian

2014-01-01

Otological microsurgery is delicate and requires high dexterity in bad ergonomic conditions. To assist surgeons in these indications, a teleoperated system, called RobOtol, is developed. This robot enhances gesture accuracy and handiness and allows exploration of new procedures for middle ear surgery. To plan new procedures that exploit the capacities given by the robot, a surgical simulator is developed. The simulation reproduces with high fidelity the behavior of the anatomical structures and can also be used as a training tool for an easier control of the robot for surgeons. In the paper, we introduce the middle ear surgical simulation and then we perform virtually two challenging procedures with the robot. We show how interactive simulation can assist in analyzing the benefits of robotics in the case of complex manipulations or ergonomics studies and allow the development of innovative surgical procedures. New robot-based microsurgical procedures are investigated. The improvement offered by RobOtol is also evaluated and discussed. PMID:25157373

A procedure for evaluating environmental impact

USGS Publications Warehouse

Leopold, Luna Bergere; Clarke, Frank Eldridge; Hanshaw, Bruce B.; Balsley, James R.

1971-01-01

The procedure does not limit the development of detail in any specific aspect of the environment; a separate expanded matrix for any environmental aspect can easily be developed within the framework provided.

32 CFR 310.38 - Training methodology and procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... procedures. (a) Each DoD Component is responsible for the development of training procedures and methodology... widest possible audience. Web-based training and video conferencing have been effective means to provide...

The impact of a medical procedure service on patient safety, procedure quality and resident training opportunities.

PubMed

Tukey, Melissa H; Wiener, Renda Soylemez

2014-03-01

At some academic hospitals, medical procedure services are being developed to provide supervision for residents performing bedside procedures in hopes of improving patient safety and resident education. There is limited knowledge of the impact of such services on procedural complication rates and resident procedural training opportunities. To determine the impact of a medical procedure service (MPS) on patient safety and resident procedural training opportunities. Retrospective cohort analysis comparing characteristics and outcomes of procedures performed by the MPS versus the primary medical service. Consecutive adults admitted to internal medicine services at a large academic hospital who underwent a bedside medical procedure (central venous catheterization, thoracentesis, paracentesis, lumbar puncture) between 1 July 2010 and 31 December 2011. The primary outcome was a composite rate of major complications. Secondary outcomes included resident participation in bedside procedures and use of "best practice" safety process measures. We evaluated 1,707 bedside procedures (548 by the MPS, 1,159 by the primary services). There were no differences in the composite rate of major complications (1.6 % vs. 1.9 %, p = 0.71) or resident participation in bedside procedures (57.0 % vs. 54.3 %, p = 0.31) between the MPS and the primary services. Procedures performed by the MPS were more likely to be successfully completed (95.8 % vs. 92.8 %, p = 0.02) and to use best practice safety process measures, including use of ultrasound guidance when appropriate (96.8 % vs. 90.0 %, p = 0.0004), avoidance of femoral venous catheterization (89.5 vs. 82.7 %, p = 0.02) and involvement of attending physicians (99.3 % vs. 57.0 %, p < 0.0001). Although use of a MPS did not significantly affect the rate of major complications or resident opportunities for training in bedside procedures, it was associated with increased use of best practice safety process measures.

36 CFR 909.170 - Compliance procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

....170 Section 909.170 Parks, Forests, and Public Property PENNSYLVANIA AVENUE DEVELOPMENT CORPORATION... PENNSYLVANIA AVENUE DEVELOPMENT CORPORATION § 909.170 Compliance procedures. (a) Except as provided in... implementation of this section. Complaints may be sent to the General Counsel, Pennsylvania Avenue Development...

Fever after intraventricular neuroendoscopic procedures in children.

PubMed

de Kunder, S L; Ter Laak-Poort, M P; Nicolai, J; Vles, J S H; Cornips, E M J

2016-06-01

The purpose of this paper was to study the incidence and clinical significance of fever after intraventricular neuroendoscopic procedures in children. We retrospectively assessed all children subjected to an intraventricular neuroendoscopic procedure between 2004 and 2015. Body temperature 6 days postoperatively, symptoms and signs, and eventual cerebrospinal fluid analysis were evaluated. Fever was defined as temperature above 38 °C. Fifty-five children (mean age 4.8 years) had 67 procedures. Forty-three children (47 procedures, 70 %) developed fever, mostly the day of surgery (n = 17; 25 %) or the next day (n = 33; 49 %). All children who were clinically ill (n = 9, including 7 with fever) suffered serious illness, as opposed to none of the children with fever without being clinically ill (n = 36). Fever was unrelated to gender, indication for, and type of procedure and did not influence ETV success rate at 3 months. Children under 1 year less frequently developed fever (p = 0.032). Fever frequently develops after intraventricular neuroendoscopic procedures in children and follows a rather predictable course, peaking the day of surgery and/or the next day, and rapidly subsiding thereafter. Fever is not a cardinal symptom except when combined with other symptoms in children who are clinically ill (which most of them are not). Close observation avoiding invasive diagnostic tests may suffice for those who are not clinically ill, while extra attention should be paid to those whose temperature rises after day 2 especially when clinically ill, as they likely suffer serious illness. We recommend to closely observe children after any intraventricular neuroendoscopic procedure for at least 5 days.

13 CFR 130.630 - Dispute resolution procedures.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 13 Business Credit and Assistance 1 2011-01-01 2011-01-01 false Dispute resolution procedures. 130.630 Section 130.630 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION SMALL BUSINESS DEVELOPMENT CENTERS § 130.630 Dispute resolution procedures. (a) Financial Disputes. (1) A recipient...

Assessment of Competence in EVAR Procedures: A Novel Rating Scale Developed by the Delphi Technique.

PubMed

Strøm, M; Lönn, L; Bech, B; Schroeder, T V; Konge, L

2017-07-01

To develop a procedure specific global rating scale for assessment of operator competence in endovascular aortic repair (EVAR). A Delphi approach was used to achieve expert consensus. A panel of 32 international experts (median 300 EVAR procedures, range 200-3000) from vascular surgery (n = 21) and radiology (n = 11) was established. The first Delphi round was based on a review of endovascular skills assessment papers, stent graft instructions for use, and structured interviews. It led to a primary pool of 83 items that were formulated as global rating scale items with tentative anchors. Iterative Delphi rounds were executed. The panellists rated the importance of each item on a 5 point Likert scale. Consensus was defined as 80% of the panel rating an item 4 or 5 in the primary round and 90% in subsequent rounds. Consensus on the final assessment tool was defined as Cronbach's alpha > .8 after a minimum of three rounds. Thirty-two of 35 invited experts participated. Three rounds of surveys were completed with a completion rate of 100% in the first two rounds and 91% in round three. The 83 primary assessment items were supplemented with five items suggested by the panel and reduced to seven pivotal assessment items that reached consensus, Cronbach's alpha = 0.82. The seven item rating scale covers key elements of competence in EVAR stent placement and deployment. Each item has well defined grades with explicit anchors at unacceptable, acceptable, and superior performance on a 5 point Likert scale. The Delphi methodology allowed for international consensus on a new procedure specific global rating scale for assessment of competence in EVAR. The resulting scale, EndoVascular Aortic Repair Assessment of Technical Expertise (EVARATE), represents key elements in the procedure. EVARATE constitutes an assessment tool for providing structured feedback to endovascular operators in training. Copyright © 2017 European Society for Vascular Surgery. Published by Elsevier

23 CFR 630.1008 - State-level processes and procedures.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., data and information resources, training, and periodic evaluation enable a systematic approach for... management procedures. States should develop and implement systematic procedures to assess work zone impacts... practices and State processes and procedures. (e) Process review. In order to assess the effectiveness of...

Pattern of venous collateral development after splenic vein occlusion in an extended Whipple procedure : comparison with collateral vein pattern in cases of sinistral portal hypertension.

PubMed

Strasberg, Steven M; Bhalla, Sanjeev; Sanchez, Luis A; Linehan, David C

2011-11-01

The risks of developing sinistral portal hypertension as a result of occlusion of the splenic vein close to its termination during a Whipple procedure are unclear. Our purpose was to compare the pattern of venous collateral development after splenic vein ligation in an extended Whipple procedure with the pattern of collateral development in cases of sinistral portal hypertension. Five patients underwent an extended Whipple procedure in which the splenic vein was divided and not reconstructed. Six to eight months later detailed mapping of venous return from the spleen was determined by contrast-enhanced multidetector computed tomography or in one case by 3D contrast-enhanced MRI. Spleen size and length of residual patent splenic vein were also measured. The literature on sinistral portal hypertension was evaluated to ascertain whether the venous collateral pattern in cases of left-sided portal hypertension was similar to the pattern that developed when the splenic vein was ligated at its termination in the Whipple procedure. A length of splenic vein remained patent in all five patients, measuring 4.5 to 11.5 cm from the spleen. Splenomegaly did not develop. Blood returned from the spleen by multiple collaterals including collaterals in the omentum and mesocolon. These types of collaterals do not develop in sinistral portal hypertension, nor is residual patent splenic vein seen. Ligation of the splenic vein close to its termination in five patients resulted in a pattern of venous return different from patients that have developed left-sided portal hypertension.

24 CFR 598.300 - Procedure for submitting a nomination.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 24 Housing and Urban Development 3 2014-04-01 2013-04-01 true Procedure for submitting a nomination. 598.300 Section 598.300 Housing and Urban Development Regulations Relating to Housing and Urban... DESIGNATIONS Designation Process § 598.300 Procedure for submitting a nomination. (a) Establishment of...

24 CFR 598.300 - Procedure for submitting a nomination.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 3 2013-04-01 2013-04-01 false Procedure for submitting a nomination. 598.300 Section 598.300 Housing and Urban Development Regulations Relating to Housing and Urban... DESIGNATIONS Designation Process § 598.300 Procedure for submitting a nomination. (a) Establishment of...

24 CFR 598.300 - Procedure for submitting a nomination.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 3 2012-04-01 2012-04-01 false Procedure for submitting a nomination. 598.300 Section 598.300 Housing and Urban Development Regulations Relating to Housing and Urban... DESIGNATIONS Designation Process § 598.300 Procedure for submitting a nomination. (a) Establishment of...

Compound estimation procedures in reliability

NASA Technical Reports Server (NTRS)

Barnes, Ron

1990-01-01

At NASA, components and subsystems of components in the Space Shuttle and Space Station generally go through a number of redesign stages. While data on failures for various design stages are sometimes available, the classical procedures for evaluating reliability only utilize the failure data on the present design stage of the component or subsystem. Often, few or no failures have been recorded on the present design stage. Previously, Bayesian estimators for the reliability of a single component, conditioned on the failure data for the present design, were developed. These new estimators permit NASA to evaluate the reliability, even when few or no failures have been recorded. Point estimates for the latter evaluation were not possible with the classical procedures. Since different design stages of a component (or subsystem) generally have a good deal in common, the development of new statistical procedures for evaluating the reliability, which consider the entire failure record for all design stages, has great intuitive appeal. A typical subsystem consists of a number of different components and each component has evolved through a number of redesign stages. The present investigations considered compound estimation procedures and related models. Such models permit the statistical consideration of all design stages of each component and thus incorporate all the available failure data to obtain estimates for the reliability of the present version of the component (or subsystem). A number of models were considered to estimate the reliability of a component conditioned on its total failure history from two design stages. It was determined that reliability estimators for the present design stage, conditioned on the complete failure history for two design stages have lower risk than the corresponding estimators conditioned only on the most recent design failure data. Several models were explored and preliminary models involving bivariate Poisson distribution and the

Nonequilibrium chemistry boundary layer integral matrix procedure

NASA Technical Reports Server (NTRS)

Tong, H.; Buckingham, A. C.; Morse, H. L.

1973-01-01

The development of an analytic procedure for the calculation of nonequilibrium boundary layer flows over surfaces of arbitrary catalycities is described. An existing equilibrium boundary layer integral matrix code was extended to include nonequilibrium chemistry while retaining all of the general boundary condition features built into the original code. For particular application to the pitch-plane of shuttle type vehicles, an approximate procedure was developed to estimate the nonequilibrium and nonisentropic state at the edge of the boundary layer.

Automatic procedures generator for orbital rendezvous maneuver

NASA Technical Reports Server (NTRS)

Kohn, W.; Van Valkenburg, J. A.; Dunn, C. K.

1985-01-01

This paper describes the development of an expert system for defining and dynamically updating procedures for an orbital rendezvous maneuver. The product of the expert system is a procedure represented by a Moore automaton. The construction is recursive and driven by a simulation of the rendezvousing bodies.

Determination of absorbed dose to water for high-energy photon and electron beams-comparison of the standards DIN 6800-2 (1997), IAEA TRS 398 (2000) and DIN 6800-2 (2006)

PubMed Central

Zakaria, Golam Abu; Schuette, Wilhelm

2007-01-01

For the determination of the absorbed dose to water for high-energy photon and electron beams the IAEA code of practice TRS-398 (2000) is applied internationally. In Germany, the German dosimetry protocol DIN 6800-2 (1997) is used. Recently, the DIN standard has been revised and published as Draft National Standard DIN 6800-2 (2006). It has adopted widely the methodology and dosimetric data of the code of practice. This paper compares these three dosimetry protocols systematically and identifies similarities as well as differences. The investigation was done with 6 and 18 MV photon as well as 5 to 21 MeV electron beams. While only cylindrical chambers were used for photon beams, measurements of electron beams were performed using cylindrical as well as plane-parallel chambers. The discrepancies in the determination of absorbed dose to water between the three protocols were 0.4% for photon beams and 1.5% for electron beams. Comparative measurements showed a deviation of less than 0.5% between our measurements following protocol DIN 6800-2 (2006) and TLD inter-comparison procedure in an external audit. PMID:21217912

Soil and sediment sample analysis for the sequential determination of natural and anthropogenic radionuclides.

PubMed

Michel, H; Levent, D; Barci, V; Barci-Funel, G; Hurel, C

2008-02-15

A new sequential method for the determination of both natural (U, Th) and anthropogenic (Sr, Cs, Pu, Am) radionuclides has been developed for application to soil and sediment samples. The procedure was optimised using a reference sediment (IAEA-368) and reference soils (IAEA-375 and IAEA-326). Reference materials were first digested using acids (leaching), 'total' acids on hot plate, and acids in microwave in order to compare the different digestion technique. Then, the separation and purification were made by anion exchange resin and selective extraction chromatography: transuranic (TRU) and strontium (SR) resins. Natural and anthropogenic alpha radionuclides were separated by uranium and tetravalent actinide (UTEVA) resin, considering different acid elution medium. Finally, alpha and gamma semiconductor spectrometer and liquid scintillation spectrometer were used to measure radionuclide activities. The results obtained for strontium-90, cesium-137, thorium-232, uranium-238, plutonium-239+240 and americium-241 isotopes by the proposed method for the reference materials provided excellent agreement with the recommended values and good chemical recoveries. Plutonium isotopes in alpha spectrometry planchet deposits could be also analysed by ICPMS.

Reliability based fatigue design and maintenance procedures

NASA Technical Reports Server (NTRS)

Hanagud, S.

1977-01-01

A stochastic model has been developed to describe a probability for fatigue process by assuming a varying hazard rate. This stochastic model can be used to obtain the desired probability of a crack of certain length at a given location after a certain number of cycles or time. Quantitative estimation of the developed model was also discussed. Application of the model to develop a procedure for reliability-based cost-effective fail-safe structural design is presented. This design procedure includes the reliability improvement due to inspection and repair. Methods of obtaining optimum inspection and maintenance schemes are treated.

Acceptance procedures for dense-graded mixes : literature review.

DOT National Transportation Integrated Search

2001-03-01

Recent literature related to acceptance procedures for dense-graded mixtures is summarized. Current state of practice and development of acceptance procedures are reviewed. Many agencies are reducing the number of process control-related parameters i...

Increasingly automated procedure acquisition in dynamic systems

NASA Technical Reports Server (NTRS)

Mathe, Nathalie; Kedar, Smadar

1992-01-01

Procedures are widely used by operators for controlling complex dynamic systems. Currently, most development of such procedures is done manually, consuming a large amount of paper, time, and manpower in the process. While automated knowledge acquisition is an active field of research, not much attention has been paid to the problem of computer-assisted acquisition and refinement of complex procedures for dynamic systems. The Procedure Acquisition for Reactive Control Assistant (PARC), which is designed to assist users in more systematically and automatically encoding and refining complex procedures. PARC is able to elicit knowledge interactively from the user during operation of the dynamic system. We categorize procedure refinement into two stages: diagnosis - diagnose the failure and choose a repair - and repair - plan and perform the repair. The basic approach taken in PARC is to assist the user in all steps of this process by providing increased levels of assistance with layered tools. We illustrate the operation of PARC in refining procedures for the control of a robot arm.

PC based temporary shielding administrative procedure (TSAP)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olsen, D.E.; Pederson, G.E.; Hamby, P.N.

1995-03-01

A completely new Administrative Procedure for temporary shielding was developed for use at Commonwealth Edison`s six nuclear stations. This procedure promotes the use of shielding, and addresses industry requirements for the use and control of temporary shielding. The importance of an effective procedure has increased since more temporary shielding is being used as ALARA goals become more ambitious. To help implement the administrative procedure, a personal computer software program was written to incorporate the procedural requirements. This software incorporates the useability of a Windows graphical user interface with extensive help and database features. This combination of a comprehensive administrative proceduremore » and user friendly software promotes the effective use and management of temporary shielding while ensuring that industry requirements are met.« less

Informed consent procedures: responsibilities of researchers in developing countries.

PubMed

Sanchez, S; Salazar, G; Tijero, M; Diaz, S

2001-10-01

We describe the informed consent procedures in a research clinic in Santiago, Chile, and a qualitative study that evaluated these procedures. The recruitment process involves information, counseling and screening of volunteers, and three or four visits to the clinic. The study explored the decision-making process of women participating in contraceptive trials through 36 interviews. Women understood the research as experimentation or progress. The decision to participate was facilitated by the information provided; time to consider it and to discuss it with partners or relatives; and perceived benefits such as quality of care, non-cost provision of methods and medical care. For some women, participation was an opportunity to express altruism. The main obstacles for participation were perceived side effects or risks. The final risk-benefit balance was strongly influenced by women's needs. Women perceived that the consent form benefited the clinic, proving that participants had made a free decision, and benefited the volunteers by warranting their right to free medical care. The most important problem detected was occasional misunderstanding of the information given on the form. We concluded that a full decision-making process enhances women's ability to exercise their right to choose, and assures research institutions that trials are conducted without coercion and that the participants are committed to the study. Researchers have the responsibility of conducting this process.

Development of Procedures for Assessing the Impact of Vocational Education Research and Development on Vocational Education (Project IMPACT). Volume 2--A Case Study of the Illinois Occupational Curriculum Project.

ERIC Educational Resources Information Center

Cheney-Stern, Marilyn R.; Phelps, L. Allen

As part of Project IMPACT's efforts to develop procedures for complying with the impact requirements of Public Law 94-482, a case study was made of the Illinois Occupational Curriculum Project (IOCP). The top-down study traced the IOCP from its developers to its users and documented measurable changes in the 1971 versus the 1979 curriculum…

32 CFR 191.6 - Procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... and a likelihood of vacancies (e.g., science and engineering positions). (11) Develop procedures for... computer support of employees with disabilities consistent with DoD participation in activities of the...

32 CFR 191.6 - Procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... and a likelihood of vacancies (e.g., science and engineering positions). (11) Develop procedures for... computer support of employees with disabilities consistent with DoD participation in activities of the...

32 CFR 191.6 - Procedures.

Code of Federal Regulations, 2013 CFR

2013-07-01

... and a likelihood of vacancies (e.g., science and engineering positions). (11) Develop procedures for... computer support of employees with disabilities consistent with DoD participation in activities of the...

32 CFR 191.6 - Procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... and a likelihood of vacancies (e.g., science and engineering positions). (11) Develop procedures for... computer support of employees with disabilities consistent with DoD participation in activities of the...

Nuclear cardiology practice and associated radiation doses in Europe: results of the IAEA Nuclear Cardiology Protocols Study (INCAPS) for the 27 European countries.

PubMed

Lindner, Oliver; Pascual, Thomas N B; Mercuri, Mathew; Acampa, Wanda; Burchert, Wolfgang; Flotats, Albert; Kaufmann, Philipp A; Kitsiou, Anastasia; Knuuti, Juhani; Underwood, S Richard; Vitola, João V; Mahmarian, John J; Karthikeyan, Ganesan; Better, Nathan; Rehani, Madan M; Kashyap, Ravi; Dondi, Maurizio; Paez, Diana; Einstein, Andrew J

2016-04-01

Nuclear cardiology is widely used to diagnose coronary artery disease and to guide patient management, but data on current practices, radiation dose-related best practices, and radiation doses are scarce. To address these issues, the IAEA conducted a worldwide study of nuclear cardiology practice. We present the European subanalysis. In March 2013, the IAEA invited laboratories across the world to document all SPECT and PET studies performed in one week. The data included age, gender, weight, radiopharmaceuticals, injected activities, camera type, positioning, hardware and software. Radiation effective dose was calculated for each patient. A quality score was defined for each laboratory as the number followed of eight predefined best practices with a bearing on radiation exposure (range of quality score 0 - 8). The participating European countries were assigned to regions (North, East, South, and West). Comparisons were performed between the four European regions and between Europe and the rest-of-the-world (RoW). Data on 2,381 European patients undergoing nuclear cardiology procedures in 102 laboratories in 27 countries were collected. A cardiac SPECT study was performed in 97.9 % of the patients, and a PET study in 2.1 %. The average effective dose of SPECT was 8.0 ± 3.4 mSv (RoW 11.4 ± 4.3 mSv; P < 0.001) and of PET was 2.6 ± 1.5 mSv (RoW 3.8 ± 2.5 mSv; P < 0.001). The mean effective doses of SPECT and PET differed between European regions (P < 0.001 and P = 0.002, respectively). The mean quality score was 6.2 ± 1.2, which was higher than the RoW score (5.0 ± 1.1; P < 0.001). Adherence to best practices did not differ significantly among the European regions (range 6 to 6.4; P = 0.73). Of the best practices, stress-only imaging and weight-adjusted dosing were the least commonly used. In Europe, the mean effective dose from nuclear cardiology is lower and the average quality score is higher than in the

Development of an accelerated creep testing procedure for geosynthetics : technical summary.

DOT National Transportation Integrated Search

1997-09-01

Temperature-creep relationships in geosynthetics vary for each type of geogrid and depend on many factors such as polymer structure, manufacture process, degree of crystallinity, and glass-transition temperature. The extrapolation procedures to predi...

DEVELOPMENT OF A TAMPER RESISTANT/INDICATING AEROSOL COLLECTION SYSTEM FOR ENVIRONMENTAL SAMPLING AT BULK HANDLING FACILITIES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sexton, L.

2012-06-06

Environmental sampling has become a key component of International Atomic Energy Agency (IAEA) safeguards approaches since its approval for use in 1996. Environmental sampling supports the IAEA's mission of drawing conclusions concerning the absence of undeclared nuclear material or nuclear activities in a Nation State. Swipe sampling is the most commonly used method for the collection of environmental samples from bulk handling facilities. However, augmenting swipe samples with an air monitoring system, which could continuously draw samples from the environment of bulk handling facilities, could improve the possibility of the detection of undeclared activities. Continuous sampling offers the opportunity tomore » collect airborne materials before they settle onto surfaces which can be decontaminated, taken into existing duct work, filtered by plant ventilation, or escape via alternate pathways (i.e. drains, doors). Researchers at the Savannah River National Laboratory and Oak Ridge National Laboratory have been working to further develop an aerosol collection technology that could be installed at IAEA safeguarded bulk handling facilities. The addition of this technology may reduce the number of IAEA inspector visits required to effectively collect samples. The principal sample collection device is a patented Aerosol Contaminant Extractor (ACE) which utilizes electrostatic precipitation principles to deposit particulates onto selected substrates. Recent work has focused on comparing traditional swipe sampling to samples collected via an ACE system, and incorporating tamper resistant and tamper indicating (TRI) technologies into the ACE system. Development of a TRI-ACE system would allow collection of samples at uranium/plutonium bulk handling facilities in a manner that ensures sample integrity and could be an important addition to the international nuclear safeguards inspector's toolkit. This work was supported by the Next Generation Safeguards Initiative (NGSI

Towards Verification of Operational Procedures Using Auto-Generated Diagnostic Trees

NASA Technical Reports Server (NTRS)

Kurtoglu, Tolga; Lutz, Robyn; Patterson-Hine, Ann

2009-01-01

The design, development, and operation of complex space, lunar and planetary exploration systems require the development of general procedures that describe a detailed set of instructions capturing how mission tasks are performed. For both crewed and uncrewed NASA systems, mission safety and the accomplishment of the scientific mission objectives are highly dependent on the correctness of procedures. In this paper, we describe how to use the auto-generated diagnostic trees from existing diagnostic models to improve the verification of standard operating procedures. Specifically, we introduce a systematic method, namely the Diagnostic Tree for Verification (DTV), developed with the goal of leveraging the information contained within auto-generated diagnostic trees in order to check the correctness of procedures, to streamline the procedures in terms of reducing the number of steps or use of resources in them, and to propose alternative procedural steps adaptive to changing operational conditions. The application of the DTV method to a spacecraft electrical power system shows the feasibility of the approach and its range of capabilities

The impact of the International Atomic Energy Agency (IAEA) program on radiation and tissue banking in Peru.

PubMed

Gamero, Emma Castro; Morales Pedraza, Jorge

2009-05-01

The tissue bank "Rosa Guerzoni Chambergo" (RGCTB) located at the Child's Health Institute was inaugurated in 1996, with the financial and technical support of the IAEA program on radiation and tissue banking. Since 1998, the biological bandage of fresh and lyophilised pigskin, amnion and bone tissue is processed routinely in this bank. In all cases, the tissue is sterilised with the use of Cobalt-60 radiation, process carried out at the Laboratories of Irradiation of the Peruvian Institute of Nuclear Energy (IPEN). The tissue bank in the Child's Health Institute helped to save lives in an accident occurred in Lima, when a New Year's fireworks celebration ran out of control in January 2002. Nearly 300 people died in the tragic blaze and hundreds more were seriously burned and injured. Eight Lima hospitals and clinics suddenly were faced with saving the lives of severely burned men, women and children. Fortunately, authorities were ready to respond to the emergency. More than 1,600 dressings were sterilised and supplied to Lima surgeons. The efforts helped save the lives of patients who otherwise might not have survived the Lima fire. Between 1998 and September 2007, 35,012 tissue grafts were produced and irradiated. Radiation sterilised tissues are used by 20 national medical institutions as well as 17 private health institutions. The tissue bank established in Peru with the support of the IAEA is now producing the following tissues: pigskin dressings, fresh and freeze-dried; bone allografts, chips, wedges and powdered, and amnion dressings air-dried. It is also now leading the elaboration of national standards, assignment being entrusted by ONDT (Organización Nacional de Donación y Transplantes; National Organisation on Donation and Transplant). This among other will permit the accreditation of the tissue bank. In this task is also participating IPEN.

The impact of the International Atomic Energy Agency (IAEA) program on radiation and tissue banking in Brazil.

PubMed

Herson, Marisa Roma; Mathor, Monica Beatriz; Morales Pedraza, Jorge

2009-05-01

Until 2000, efforts into organising tissue banks in Brazil had not progressed far beyond small "in house" tissue storage repositories, usually annexed to Orthopaedic Surgery Services. Despite the professional entrepreneurship of those working as part time tissue bankers in such operations, best practices in tissue banking were not always followed due to the lack of regulatory standards, specialised training, adequate facilities and dedicated personnel. The Skin Bank of the Plastic Surgery Department of the Hospital das Clinicas of Sao Paulo, the single skin bank in Brazil, was not an exception. Since 1956, restricted and unpredictable amounts of skin allografts were stored under refrigeration for short periods under very limited quality controls. As in most "tissue banks" at that time in Brazil, medical and nursing staff worked on a volunteer and informal basis undergoing no specific training. IAEA supported the implementation of the tissue banking program in Brazil through the regional project RLA/7/009 "Quality system for the production of irradiated sterilised grafts" (1998-2000) and through two interregional projects INT/6/049 "Interregional Centre of Excellence in Tissue Banking", during the period 2002-2004 and INT/6/052 "Improving the Quality of Production and Uses of Radiation Sterilised Tissue Grafts", during the period 2002-2004. In 2001-2002, the first two years of operation of the HC-Tissue Bank, 53 skin transplants were carried out instead of the previous 4-5 a year. During this period, 75 individuals donated skin tissue, generating approximately 90,000 cm(2) of skin graft. The IAEA program were of great benefit to Brazilian tissue banking which has evolved from scattered make shift small operations to a well-established, high quality tissue banking scenario.

[Standard operating procedures in ethic committees].

PubMed

Czarkowski, Marek

2006-02-01

Polish ethic committees should have to work together in order to maintain and develop high quality standards in the protection of human subjects. Exchanging knowledge, know-how and information polish ethic committees should have to implement standard operating procedures. Procedures should improve quality and proficiency of all types of ethic committee's activities. Standard operating procedures should cover as important problems as conflict of interest, trial's insurance or elections of ethic committees. The opinions of experts who have been reviewing medical research projects for several years may prove to be especially valuable in this setting. Governmental initiatives and creation of forum for polish ethic committees are essential in the effective standardisation, coordination and implementation of procedures in regional ethic committees. These projects need support via public funding from our authorities.

The calibration of a Scanditronix-Wellhöfer thimble chamber for photon dosimetry using the IAEA TRS 277 code of practice.

PubMed

Fourie, O L

2004-03-01

This note investigates the calibration of a Scanditronix-Wellhöfer type FC65-G ionisation chamber to be used in clinical photon dosimetry. The current Adaptation by the Australasian College of Physical Scientists and Engineers in Medicine (ACPSEM) of the IAEA TRS 277 dosimetry protocol makes no provision for this type of chamber. The absorbed dose to air calibration coefficient ND was therefore calculated from the air kerma calibration coefficient NK using the formalism of the IAEA TRS 277 protocol and it is shown that the value of the correction factor kmkatt for the FC65-G chamber is identical to that of the NE 2571 chamber. ND was also determined experimentally from a cross calibration against an NE 2571 dosimetry. It was found that there is a good correspondence between the calculated and measured values. To establish to what extent the ACPSEM Adaptation can be used for the FC65-G chamber, values for the ratio of stopping powers in water and air (Sw,air)Q and the perturbation correction factor pQ were calculated using the TRS 277 protocol. From these results it is shown that over the range of beam qualities TPR20,10 = 0.59 to TPR20,10 = 0.78 the Adaptation can be used for the FC65-G chamber.

Procedures and Policies Manual

ERIC Educational Resources Information Center

Davis, Jane M.

2006-01-01

This document was developed by the Middle Tennessee State University James E. Walker Library Collection Management Department to provide policies and procedural guidelines for the cataloging and processing of bibliographic materials. This document includes policies for cataloging monographs, serials, government documents, machine-readable data…

Latin American dose survey results in mammography studies under IAEA programme: radiological protection of patients in medical exposures (TSA3).

PubMed

Mora, Patricia; Blanco, Susana; Khoury, Helen; Leyton, Fernando; Cárdenas, Juan; Defaz, María Yolanda; Garay, Fernando; Telón, Flaviano; Aguilar, Juan Garcia; Roas, Norma; Gamarra, Mirtha; Blanco, Daniel; Quintero, Ana Rosa; Nader, Alejandro

2015-03-01

Latin American countries (Argentina, Brazil, Chile, Costa Rica, Cuba, Ecuador, El Salvador, Guatemala, Mexico, Nicaragua, Paraguay, Uruguay and Venezuela) working under the International Atomic Energy Agency (IAEA) Technical Cooperation Programme: TSA3 Radiological Protection of Patients in Medical Exposures have joined efforts in the optimisation of radiation protection in mammography practice. Through surveys of patient doses, the region has a unique database of diagnostic reference levels for analogue and digital equipment that will direct future optimisation activities towards the early detection of breast cancer among asymptomatic women. During RLA9/057 (2007-09) 24 institutions participated with analogue equipment in a dose survey. Regional training on methodology and measurement equipment was addressed in May 2007. The mean glandular dose (DG) was estimated using the incident kerma in air and relevant conversion coefficients for both projections craneo caudal and mediolateral oblique (CC and MLO). For Phase 2, RLA9/067 (2010-11), it was decided to include also digital systems in order to see their impact in future dose optimisation activities. Any new country that joined the project received training in the activities through IAEA expert missions. Twenty-nine new institutions participated (9 analogue and 20 digital equipment). A total of 2262 patient doses were collected during this study and from them D(G) (mGy) for both projections were estimated for each institution and country. Regional results (75 percentile in mGy) show for CC and MLO views, respectively: RLA9/057 (analogue) 2.63 and 3.17; RLA/067: 2.57 and 3.15 (analogue) and 2.69 and 2.90 (digital). Regarding only digital equipment for CC and MLO, respectively, computed radiography systems showed 2.59 and 2.78 and direct digital radiography (DDR) systems 2.78 and 3.04. Based on the IAEA Basic Safety Standard (BSS) reference dose (3 mGy), it can be observed that there is enough room to start

The Measurement of Values: Effects of Different Assessment Procedures

ERIC Educational Resources Information Center

Feather, N. T.

1973-01-01

Rating and pair-comparison procedures for assessing the importance of terminal and instrumental values were compared with the standard ranking procedure developed by Rokeach. Effects of order of presentation of of the value sets were also investigated. Neither procedure nor order had replicable effect though some sex differences were apparent. (TO)

Procedural Quantum Programming

NASA Astrophysics Data System (ADS)

Ömer, Bernhard

2002-09-01

While classical computing science has developed a variety of methods and programming languages around the concept of the universal computer, the typical description of quantum algorithms still uses a purely mathematical, non-constructive formalism which makes no difference between a hydrogen atom and a quantum computer. This paper investigates, how the concept of procedural programming languages, the most widely used classical formalism for describing and implementing algorithms, can be adopted to the field of quantum computing, and how non-classical features like the reversibility of unitary transformations, the non-observability of quantum states or the lack of copy and erase operations can be reflected semantically. It introduces the key concepts of procedural quantum programming (hybrid target architecture, operator hierarchy, quantum data types, memory management, etc.) and presents the experimental language QCL, which implements these principles.

Robot-assisted procedures in pediatric neurosurgery.

PubMed

De Benedictis, Alessandro; Trezza, Andrea; Carai, Andrea; Genovese, Elisabetta; Procaccini, Emidio; Messina, Raffaella; Randi, Franco; Cossu, Silvia; Esposito, Giacomo; Palma, Paolo; Amante, Paolina; Rizzi, Michele; Marras, Carlo Efisio

2017-05-01

OBJECTIVE During the last 3 decades, robotic technology has rapidly spread across several surgical fields due to the continuous evolution of its versatility, stability, dexterity, and haptic properties. Neurosurgery pioneered the development of robotics, with the aim of improving the quality of several procedures requiring a high degree of accuracy and safety. Moreover, robot-guided approaches are of special interest in pediatric patients, who often have altered anatomy and challenging relationships between the diseased and eloquent structures. Nevertheless, the use of robots has been rarely reported in children. In this work, the authors describe their experience using the ROSA device (Robotized Stereotactic Assistant) in the neurosurgical management of a pediatric population. METHODS Between 2011 and 2016, 116 children underwent ROSA-assisted procedures for a variety of diseases (epilepsy, brain tumors, intra- or extraventricular and tumor cysts, obstructive hydrocephalus, and movement and behavioral disorders). Each patient received accurate preoperative planning of optimal trajectories, intraoperative frameless registration, surgical treatment using specific instruments held by the robotic arm, and postoperative CT or MR imaging. RESULTS The authors performed 128 consecutive surgeries, including implantation of 386 electrodes for stereo-electroencephalography (36 procedures), neuroendoscopy (42 procedures), stereotactic biopsy (26 procedures), pallidotomy (12 procedures), shunt placement (6 procedures), deep brain stimulation procedures (3 procedures), and stereotactic cyst aspiration (3 procedures). For each procedure, the authors analyzed and discussed accuracy, timing, and complications. CONCLUSIONS To the best their knowledge, the authors present the largest reported series of pediatric neurosurgical cases assisted by robotic support. The ROSA system provided improved safety and feasibility of minimally invasive approaches, thus optimizing the surgical

Development of an efficient Procedure for Resist Wall Space Experiment

NASA Astrophysics Data System (ADS)

Matsumoto, Shouhei; Kumasaki, Saori; Higuchi, Sayoko; Kirihata, Kuniaki; Inoue, Yasue; Fujie, Miho; Soga, Kouichi; Wakabayashi, Kazuyuki; Hoson, Takayuki

The Resist Wall space experiment aims to examine the role of the cortical microtubule-plasma membrane-cell wall continuum in plant resistance to the gravitational force, thereby clarifying the mechanism of gravity resistance. For this purpose, we will cultivate Arabidopsis mutants defective in organization of cortical microtubules (tua6 ) or synthesis of membrane sterols (hmg1 ) as well as the wild type under microgravity and 1 g conditions in the European Modular Cultivation System on the International Space Station up to reproductive stage, and compare phenotypes on growth and development. We will also analyze cell wall properties and gene expression levels using collected materials. However, the amounts of materials collected will be severely limited, and we should develop an efficient procedure for this space experiment. In the present study, we examined the possibility of analyzing various parameters successively using the identical material. On orbit, plant materials will be fixed with RNAlater solution, kept at 4° C for several days and then frozen in a freezer at -20° C. We first examined whether the cell wall extensibility of inflorescence stems can be measured after RNAlater fixation. The gradient of the cell wall extensibility along inflorescence stems was detected in RNAlater-fixed materials as in methanol-killed ones. The sufficient amounts of RNA to analyze the gene expression were also obtained from the materials after measurement of the cell wall extensibility. Furthermore, the levels and composition of cell wall polysaccharides could be measured using the materials after extraction of RNA. These results show that we can analyze the physical and chemical properties of the cell wall as well as gene expression using the identical material obtained in the space experiments.

Development of an integrated, unattended assay system for LWR-MOX fuel pellet trays

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stewart, J.E.; Hatcher, C.R.; Pollat, L.L.

1994-08-01

Four identical unattended plutonium assay systems have been developed for use at the new light-water-reactor mixed oxide (LWR-MOX) fuel fabrication facility at Hanau, Germany. The systems provide quantitative plutonium verification for all MOX pellet trays entering or leaving a large, intermediate store. Pellet-tray transport and storage systems are highly automated. Data from the ``I-Point`` (information point) assay systems will be shared by the Euratom and International Atomic Energy Agency (IAEA) Inspectorates. The I-Point system integrates, for the first time, passive neutron coincidence counting (NCC) with electro-mechanical sensing (EMS) in unattended mode. Also, provisions have been made for adding high-resolution gammamore » spectroscopy. The system accumulates data for every tray entering or leaving the store between inspector visits. During an inspection, data are analyzed and compared with operator declarations for the previous inspection period, nominally one month. Specification of the I-point system resulted from a collaboration between the IAEA, Euratom, Siemens, and Los Alamos. Hardware was developed by Siemens and Los Alamos through a bilateral agreement between the German Federal Ministry of Research and Technology (BMFT) and the US DOE. Siemens also provided the EMS subsystem, including software. Through the USSupport Program to the IAEA, Los Alamos developed the NCC software (NCC COLLECT) and also the software for merging and reviewing the EMS and NCC data (MERGE/REVIEW). This paper describes the overall I-Point system, but emphasizes the NCC subsystem, along with the NCC COLLECT and MERGE/REVIEW codes. We also summarize comprehensive testing results that define the quality of assay performance.« less

Automated procedure execution for space vehicle autonomous control

NASA Technical Reports Server (NTRS)

Broten, Thomas A.; Brown, David A.

1990-01-01

Increased operational autonomy and reduced operating costs have become critical design objectives in next-generation NASA and DoD space programs. The objective is to develop a semi-automated system for intelligent spacecraft operations support. The Spacecraft Operations and Anomaly Resolution System (SOARS) is presented as a standardized, model-based architecture for performing High-Level Tasking, Status Monitoring and automated Procedure Execution Control for a variety of spacecraft. The particular focus is on the Procedure Execution Control module. A hierarchical procedure network is proposed as the fundamental means for specifying and representing arbitrary operational procedures. A separate procedure interpreter controls automatic execution of the procedure, taking into account the current status of the spacecraft as maintained in an object-oriented spacecraft model.

Medical tongue piercing – development and evaluation of a surgical protocol and the perception of procedural discomfort of the participants

PubMed Central

2014-01-01

Background A system providing disabled persons with control of various assistive devices with the tongue has been developed at Aalborg University in Denmark. The system requires an activation unit attached to the tongue with a small piercing. The aim of this study was to establish and evaluate a safe and tolerable procedure for medical tongue piercing and to evaluate the expected and perceived procedural discomfort. Methods Four tetraplegic subjects volunteered for the study. A surgical protocol for a safe insertion of a tongue barbell piercing was presented using sterilized instruments and piercing parts. Moreover, post-procedural observations of participant complications such as bleeding, edema, and infection were recorded. Finally, procedural discomforts were monitored by VAS scores of pain, changes in taste and speech as well as problems related to hitting the teeth. Results The piercings were all successfully inserted in less than 5 min and the pain level was moderate compared with oral injections. No bleeding, infection, embedding of the piercing, or tooth/gingival injuries were encountered; a moderate edema was found in one case without affecting the speech. In two cases the piercing rod later had to be replaced by a shorter rod, because participants complained that the rod hit their teeth. The replacements prevented further problems. Moreover, loosening of balls was encountered, which could be prevented with the addition of dental glue. No cases of swallowing or aspiration of the piercing parts were recorded. Conclusions The procedure proved simple, fast, and safe for insertion of tongue piercings for tetraplegic subjects in a clinical setting. The procedure represented several precautions in order to avoid risks in these susceptible participants with possible co-morbidity. No serious complications were encountered, and the procedure was found tolerable to the participants. The procedure may be used in future studies with tongue piercings being a

A FLOW-THROUGH TESTING PROCEDURE WITH DUCKWEED (LEMNA MINOR L.)

EPA Science Inventory

Lemna minor is one of the smallest flowering plants. Because of its floating habit, ease of culture, and small size it is well adapted for laboratory investigations. Procedures for flow-through tests were developed. Testing procedures were developed with this apparatus. By using ...

Development of a nucleic Acid extraction procedure for simultaneous recovery of DNA and RNA from diverse microbes in water.

PubMed

Hill, Vincent R; Narayanan, Jothikumar; Gallen, Rachel R; Ferdinand, Karen L; Cromeans, Theresa; Vinjé, Jan

2015-05-26

Drinking and environmental water samples contain a diverse array of constituents that can interfere with molecular testing techniques, especially when large volumes of water are concentrated to the small volumes needed for effective molecular analysis. In this study, a suite of enteric viruses, bacteria, and protozoan parasites were seeded into concentrated source water and finished drinking water samples, in order to investigate the relative performance of nucleic acid extraction techniques for molecular testing. Real-time PCR and reverse transcription-PCR crossing threshold (CT) values were used as the metrics for evaluating relative performance. Experimental results were used to develop a guanidinium isothiocyanate-based lysis buffer (UNEX buffer) that enabled effective simultaneous extraction and recovery of DNA and RNA from the suite of study microbes. Procedures for bead beating, nucleic acid purification, and PCR facilitation were also developed and integrated in the protocol. The final lysis buffer and sample preparation procedure was found to be effective for a panel of drinking water and source water concentrates when compared to commercial nucleic acid extraction kits. The UNEX buffer-based extraction protocol enabled PCR detection of six study microbes, in 100 L finished water samples from four drinking water treatment facilities, within three CT values (i.e., within 90% difference) of the reagent-grade water control. The results from this study indicate that this newly formulated lysis buffer and sample preparation procedure can be useful for standardized molecular testing of drinking and environmental waters.

Development of a Nucleic Acid Extraction Procedure for Simultaneous Recovery of DNA and RNA from Diverse Microbes in Water

PubMed Central

Hill, Vincent R.; Narayanan, Jothikumar; Gallen, Rachel R.; Ferdinand, Karen L.; Cromeans, Theresa; Vinjé, Jan

2015-01-01

Drinking and environmental water samples contain a diverse array of constituents that can interfere with molecular testing techniques, especially when large volumes of water are concentrated to the small volumes needed for effective molecular analysis. In this study, a suite of enteric viruses, bacteria, and protozoan parasites were seeded into concentrated source water and finished drinking water samples, in order to investigate the relative performance of nucleic acid extraction techniques for molecular testing. Real-time PCR and reverse transcription-PCR crossing threshold (CT) values were used as the metrics for evaluating relative performance. Experimental results were used to develop a guanidinium isothiocyanate-based lysis buffer (UNEX buffer) that enabled effective simultaneous extraction and recovery of DNA and RNA from the suite of study microbes. Procedures for bead beating, nucleic acid purification, and PCR facilitation were also developed and integrated in the protocol. The final lysis buffer and sample preparation procedure was found to be effective for a panel of drinking water and source water concentrates when compared to commercial nucleic acid extraction kits. The UNEX buffer-based extraction protocol enabled PCR detection of six study microbes, in 100 L finished water samples from four drinking water treatment facilities, within three CT values (i.e., within 90% difference) of the reagent-grade water control. The results from this study indicate that this newly formulated lysis buffer and sample preparation procedure can be useful for standardized molecular testing of drinking and environmental waters. PMID:26016775

Development of a purification procedure for the isolation of nucleosides from urine prior to mass spectrometric analysis.

PubMed

Dudley, E; El-Shakawi, S; Games, D E; Newton, R P

2000-03-01

A chromatographic separation of nucleosides from urine has been developed in order to facilitate their mass spectrometric analysis for clinical diagnosis. A number of chromatographic resins were studied in order to develop an effective and efficient purification procedure. The optimized sequential protocol comprises a centrifugation, acidification and neutralization step, followed by application of an affinity chromatographic column and finally further separation on an acidic cation exchange column and a basic anion exchanger. This scheme shows effective clean-up of a standard radiolabelled nucleoside with a recovery of 92.5%, and recovery of nucleosides added to urine samples before extraction showed recoveries of 72-82%.

24 CFR 115.203 - Interim certification procedures.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Interim certification procedures. 115.203 Section 115.203 Housing and Urban Development Regulations Relating to Housing and Urban Development OFFICE OF ASSISTANT SECRETARY FOR EQUAL OPPORTUNITY, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT...

24 CFR 115.203 - Interim certification procedures.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 24 Housing and Urban Development 1 2014-04-01 2014-04-01 false Interim certification procedures. 115.203 Section 115.203 Housing and Urban Development Regulations Relating to Housing and Urban Development OFFICE OF ASSISTANT SECRETARY FOR EQUAL OPPORTUNITY, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT...

24 CFR 115.203 - Interim certification procedures.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 1 2013-04-01 2013-04-01 false Interim certification procedures. 115.203 Section 115.203 Housing and Urban Development Regulations Relating to Housing and Urban Development OFFICE OF ASSISTANT SECRETARY FOR EQUAL OPPORTUNITY, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT...

24 CFR 115.203 - Interim certification procedures.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 1 2012-04-01 2012-04-01 false Interim certification procedures. 115.203 Section 115.203 Housing and Urban Development Regulations Relating to Housing and Urban Development OFFICE OF ASSISTANT SECRETARY FOR EQUAL OPPORTUNITY, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT...

24 CFR 115.203 - Interim certification procedures.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 1 2011-04-01 2011-04-01 false Interim certification procedures. 115.203 Section 115.203 Housing and Urban Development Regulations Relating to Housing and Urban Development OFFICE OF ASSISTANT SECRETARY FOR EQUAL OPPORTUNITY, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT...

Evaluation of contract time estimation and contracting procedures for louisiana department of transportation and development construction projects : final report : volume I.

DOT National Transportation Integrated Search

1995-09-11

The purpose of the research was to provide the Louisiana Department of Transportation and Development (LaDOTD) with a systematic approach to the determination of contract time and to explore innovative contracting procedures that may prove beneficial...

Skin resurfacing procedures: new and emerging options

PubMed Central

Loesch, Mathew M; Somani, Ally-Khan; Kingsley, Melanie M; Travers, Jeffrey B; Spandau, Dan F

2014-01-01

The demand for skin resurfacing and rejuvenating procedures has progressively increased in the last decade and has sparked several advances within the skin resurfacing field that promote faster healing while minimizing downtime and side effects for patients. Several technological and procedural skin resurfacing developments are being integrated into clinical practices today allowing clinicians to treat a broader range of patients’ skin types and pathologies than in years past, with noteworthy outcomes. This article will discuss some emerging and developing resurfacing therapies and treatments that are present today and soon to be available. PMID:25210469

Skin resurfacing procedures: new and emerging options.

PubMed

Loesch, Mathew M; Somani, Ally-Khan; Kingsley, Melanie M; Travers, Jeffrey B; Spandau, Dan F

2014-01-01

The demand for skin resurfacing and rejuvenating procedures has progressively increased in the last decade and has sparked several advances within the skin resurfacing field that promote faster healing while minimizing downtime and side effects for patients. Several technological and procedural skin resurfacing developments are being integrated into clinical practices today allowing clinicians to treat a broader range of patients' skin types and pathologies than in years past, with noteworthy outcomes. This article will discuss some emerging and developing resurfacing therapies and treatments that are present today and soon to be available.

"Heidelberg standard examination" and "Heidelberg standard procedures" - Development of faculty-wide standards for physical examination techniques and clinical procedures in undergraduate medical education.

PubMed

Nikendei, C; Ganschow, P; Groener, J B; Huwendiek, S; Köchel, A; Köhl-Hackert, N; Pjontek, R; Rodrian, J; Scheibe, F; Stadler, A-K; Steiner, T; Stiepak, J; Tabatabai, J; Utz, A; Kadmon, M

2016-01-01

The competent physical examination of patients and the safe and professional implementation of clinical procedures constitute essential components of medical practice in nearly all areas of medicine. The central objective of the projects "Heidelberg standard examination" and "Heidelberg standard procedures", which were initiated by students, was to establish uniform interdisciplinary standards for physical examination and clinical procedures, and to distribute them in coordination with all clinical disciplines at the Heidelberg University Hospital. The presented project report illuminates the background of the initiative and its methodological implementation. Moreover, it describes the multimedia documentation in the form of pocketbooks and a multimedia internet-based platform, as well as the integration into the curriculum. The project presentation aims to provide orientation and action guidelines to facilitate similar processes in other faculties.

Procedure to Generate the MPACT Multigroup Library

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Kang Seog

The CASL neutronics simulator MPACT is under development for the neutronics and T-H coupled simulation for the light water reactor. The objective of this document is focused on reviewing the current procedure to generate the MPACT multigroup library. Detailed methodologies and procedures are included in this document for further discussion to improve the MPACT multigroup library.

24 CFR 570.509 - Grant closeout procedures.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 3 2010-04-01 2010-04-01 false Grant closeout procedures. 570.509 Section 570.509 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued) OFFICE OF ASSISTANT SECRETARY FOR COMMUNITY PLANNING AND DEVELOPMENT, DEPARTMENT OF HOUSING AND...

Development of a modified cortisol extraction procedure for intermediately sized fish not amenable to whole-body or plasma extraction methods.

PubMed

Guest, Taylor W; Blaylock, Reginald B; Evans, Andrew N

2016-02-01

The corticosteroid hormone cortisol is the central mediator of the teleost stress response. Therefore, the accurate quantification of cortisol in teleost fishes is a vital tool for addressing fundamental questions about an animal's physiological response to environmental stressors. Conventional steroid extraction methods using plasma or whole-body homogenates, however, are inefficient within an intermediate size range of fish that are too small for phlebotomy and too large for whole-body steroid extractions. To assess the potential effects of hatchery-induced stress on survival of fingerling hatchery-reared Spotted Seatrout (Cynoscion nebulosus), we developed a novel extraction procedure for measuring cortisol in intermediately sized fish (50-100 mm in length) that are not amenable to standard cortisol extraction methods. By excising a standardized portion of the caudal peduncle, this tissue extraction procedure allows for a small portion of a larger fish to be sampled for cortisol, while minimizing the potential interference from lipids that may be extracted using whole-body homogenization procedures. Assay precision was comparable to published plasma and whole-body extraction procedures, and cortisol quantification over a wide range of sample dilutions displayed parallelism versus assay standards. Intra-assay %CV was 8.54%, and average recovery of spiked samples was 102%. Also, tissue cortisol levels quantified using this method increase 30 min after handling stress and are significantly correlated with blood values. We conclude that this modified cortisol extraction procedure provides an excellent alternative to plasma and whole-body extraction procedures for intermediately sized fish, and will facilitate the efficient assessment of cortisol in a variety of situations ranging from basic laboratory research to industrial and field-based environmental health applications.