Sample records for ideal stoichiometric composition

  1. Femtosecond laser ablation-based mass spectrometry. An ideal tool for stoichiometric analysis of thin films

    DOE PAGES

    LaHaye, Nicole L.; Kurian, Jose; Diwakar, Prasoon K.; ...

    2015-08-19

    An accurate and routinely available method for stoichiometric analysis of thin films is a desideratum of modern materials science where a material’s properties depend sensitively on elemental composition. We thoroughly investigated femtosecond laser ablation-inductively coupled plasma-mass spectrometry (fs-LA-ICP-MS) as an analytical technique for determination of the stoichiometry of thin films down to the nanometer scale. The use of femtosecond laser ablation allows for precise removal of material with high spatial and depth resolution that can be coupled to an ICP-MS to obtain elemental and isotopic information. We used molecular beam epitaxy-grown thin films of LaPd (x)Sb 2 and T´-La 2CuOmore » 4 to demonstrate the capacity of fs-LA-ICP-MS for stoichiometric analysis and the spatial and depth resolution of the technique. Here we demonstrate that the stoichiometric information of thin films with a thickness of ~10 nm or lower can be determined. Furthermore, our results indicate that fs-LA-ICP-MS provides precise information on the thin film-substrate interface and is able to detect the interdiffusion of cations.« less

  2. Proximate biochemical composition and caloric content calculated from elemental CHN analysis: a stoichiometric concept.

    PubMed

    Gnaiger, E; Bitterlich, G

    1984-06-01

    Carbohydrate, lipid, and protein compositions are stoichiometrically related to organic CHN (carbon, hydrogen, nitrogen) contents. Elemental CHN analyses of total biomass and ash, therefore, provide a basis for the calculation of proximate biochemical composition and bomb caloric value. The classical nitrogen to protein conversion factor (6.25) should be replaced by 5.8±0.13. A linear relation exists between the mass fraction of non-protein carbon and the carbohydrate and lipid content. Residual water in dry organic matter can be estimated with the additional information derived from hydrogen measurements.The stoichiometric CHN method and direct biochemical analysis agreed within 10% of ash-free dry biomass (for muscle, liver and fat tissue of silver carp; gut contents composed of detritus and algae; commercial fish food). The detrital material, however, had to be corrected for non-protein nitrogen.A linear relationship between bomb caloric value and organic carbon fractions was derived on the basis of thermodynamic and stoichiometric principles, in agreement with experimental data published for bacteria, algae, protozoa and invertebrates. The highly automatic stoichiometric CHN method for the separation of nutrient contents in biomass extends existing ecophysiological concepts for the construction of balanced carbon and nitrogen, as well as biochemical and energy budgets.

  3. Off-stoichiometric defect clustering in irradiated oxides

    NASA Astrophysics Data System (ADS)

    Khalil, Sarah; Allen, Todd; EL-Azab, Anter

    2017-04-01

    A cluster dynamics model describing the formation of vacancy and interstitial clusters in irradiated oxides has been developed. The model, which tracks the composition of the oxide matrix and the defect clusters, was applied to the early stage formation of voids and dislocation loops in UO2, and the effects of irradiation temperature and dose rate on the evolution of their densities and composition was investigated. The results show that Frenkel defects dominate the nucleation process in irradiated UO2. The results also show that oxygen vacancies drive vacancy clustering while the migration energy of uranium vacancies is a rate-limiting factor for the nucleation and growth of voids. In a stoichiometric UO2 under irradiation, off-stoichiometric vacancy clusters exist with a higher concentration of hyper-stoichiometric clusters. Similarly, off-stoichiometric interstitial clusters form with a higher concentration of hyper-stoichiometric clusters. The UO2 matrix was found to be hyper-stoichiometric due to the accumulation of uranium vacancies.

  4. Is the Reaction Equilibrium Composition in Non-ideal Mixtures Uniquely Determined by the Initial Composition?

    NASA Astrophysics Data System (ADS)

    Sefcik, Jan

    1998-05-01

    Reaction equilibrium can be mathematically described by the equilibrium equation and the reaction equilibrium composition can be calculated by solving this equation. It can be proved by non-elementary thermodynamic arguments that for a generic system with given initial composition, temperature and pressure there is a unique stable equilibrium state corresponding to the global minimum of the Gibbs free energy function. However, when the concept of equilibrium is introduced in undergraduate chemistry and chemical engineering courses, such arguments are generally not accessible. When there is a single reaction equilibrium among mixture components and the components form an ideal mixture, it has been demonstrated by a simple, elegant mathematical argument that there is a unique composition satisfying the equilibrium equation. It has been also suggested that this particular argument extends to non-ideal mixtures by simply incorporating activity coefficients. We show that the argument extension to non-ideal systems is not generally valid. Increasing non-ideality can result in non-monotonicity of the function crucial for the simple uniqueness argument, and only later it leads to non-uniqueness and hence phase separation. The main feature responsible for this is a composition dependence of activity coefficients in non-ideal mixtures.

  5. Non-Ideal Detonation Properties of Ammonium Nitrate and Activated Carbon Mixtures

    NASA Astrophysics Data System (ADS)

    Miyake, Atsumi; Echigoya, Hiroshi; Kobayashi, Hidefumi; Ogawa, Terushige; Katoh, Katsumi; Kubota, Shiro; Wada, Yuji; Ogata, Yuji

    To obtain a better understanding of detonation properties of ammonium nitrate (AN) and activated carbon (AC) mixtures, steel tube tests with several diameters were carried out for various compositions of powdered AN and AC mixtures and the influence of the charge diameter on the detonation velocity was investigated. The results showed that the detonation velocity increased with the increase of the charge diameter. The experimentally observed values were far below the theoretically predicted values made by the thermodynamic CHEETAH code and they showed so-called non-ideal detonation. The extrapolated detonation velocity of stoichiometric composition to the infinite diameter showed a good agreement with the theoretical value.

  6. Cathodoluminescence of SiOx under-stoichiometric silica layers

    NASA Astrophysics Data System (ADS)

    Salh, Roushdey; von Czarnowski, A.; Zamoryanskaya, M. V.; Kolesnikova, E. V.; Fitting, H.-J.

    2006-06-01

    Under-stoichiometric thin silica layers SiOx with different stoichiometric degree 1 x 2, were prepared by thermal evaporation of silicon monoxide in vacuum and in ambient oxygen atmosphere of various pressure onto crystalline silicon substrates. The chemical composition has been determined by Fourier transform infrared spectroscopy (FTIR). A special formula is derived to correlate the stoichiometric degree x with the wavenumber of the main TO stretching mode (Si-O-Si) in silica, finally to determine the actual composition values x of the layers. Cathodoluminescence (CL) of these layers shows the development of typical amorphous SiO2 luminescence bands at the composition threshold x > 1.5 and then onwards to x = 2. These luminescence bands were observed at 4.3, 2.7, 2.15, and 1.9 eV. The green-yellow luminescence (2.15 eV) is strongly increasing with the annealing temperature up to 1300 °C and is assigned to phase separation of SiOx into Si and SiO2 and formation of hexamer silicon rings in the understoichiometric silica network. Finally we observe Si nanoclusters by means of transmission elec- tron microscopy (TEM) micrographs.

  7. Prediction of a New Phase of Cu x S near Stoichiometric Composition

    DOE PAGES

    Khatri, Prashant; Huda, Muhammad N.

    2015-01-01

    Cumore » 2 S is known to be a promising solar absorber material due to its suitable band gap and the abundance of its constituent elements. 2 S is known to have complex phase structures depending on the concentration of vacancies. Its instability of phases is due to favorable formation of vacancies and the mobility of atoms within the crystal. Understanding its phase structures is of crucial important for its application as solar absorber material. In this paper, we have predicted a new crystal phase of copper sulfide ( x S) around chemical composition of x = 1.98 by utilizing crystal database search and density functional theory. We have shown that this new crystal phase of x S is more favorable than low chalcocite structure even at stoichiometric composition of x = 2 . However, vacancy formation probability was found to be higher in this new phase than the low chalcocite structure.« less

  8. Does the stoichiometric carbon:phosphorus knife edge apply for predaceous copepods?

    PubMed

    Laspoumaderes, Cecilia; Modenutti, Beatriz; Elser, James J; Balseiro, Esteban

    2015-06-01

    Recent work has indicated that stoichiometric food quality in terms of the carbon:phosphorus (C:P) ratio affects consumers whether the imbalance involves a deficit or an excess of nutrients; hence, organisms exist on a "stoichiometric knife edge". While previous studies have focused primarily on autotroph-herbivore trophic transfer, nutritional imbalances may also affect the interactions between species at higher trophic levels. Since the foods of carnivores are normally stoichiometrically similar to the body compositions of those carnivores, they may be more severely affected than herbivores if imbalances become pronounced. We analysed the response of the predatory copepod Parabroteas sarsi to monospecific diet treatments consisting of high and low C:P prey items. These dietary treatments strongly affected the predator's elemental composition and growth, although prey selection, excretion, egestion, and respiration rates were not affected. We suggest that, due to their low threshold elemental ratio and a narrow C:P stoichiometric knife edge, these predators are highly vulnerable to stoichiometric imbalances, whether an excess or a deficit of nutrients is involved. Our results demonstrating this high sensitivity to prey C:P ratio show that the stoichiometric knife edge may apply to not only herbivores but also higher trophic levels. Thus, predators such as P. sarsi, with a much narrower range of food quality, may also be strongly affected by fluctuations in the quality of their prey, with negative consequences for their secondary production.

  9. Thermoelectric properties of non-stoichiometric lanthanum sulfides

    NASA Technical Reports Server (NTRS)

    Shapiro, E.; Danielson, L. R.

    1983-01-01

    The lanthanum sulfides are promising candidate materials for high-efficiency thermoelectric applications at temperatures up to 1300 C. The non-stoichiometric lanthanum sulfides (LaS(x), where x is in the range 1.33-1.50) appear to possess the most favorable thermoelectric properties. The Seebeck coefficient and resistivity vary significantly with composition, so that an optimum value of alpha sq/rho (where alpha is the Seebeck coefficient and rho is the resistivity) can be chosen. The thermal conductivity remains approximately constant with stoichiometry, so a material with an optimum value of alpha sq/rho should possess the optimum figure-of-merit. Data for the Seebeck coefficient and electrical resistivity of non-stoichiometric lanthanum sulfides will be pressed, together with structural properties of these materials.

  10. Extensive Natural Intraspecific Variation in Stoichiometric (C:N:P) Composition in Two Terrestrial Insect Species

    PubMed Central

    Bertram, S. M.; Bowen, M.; Kyle, M.; Schade, J. D.

    2008-01-01

    Heterotrophic organisms must obtain essential elements in sufficient quantities from their food. Because plants naturally exhibit extensive variation in their elemental content, it is important to quantify the within-species stoichiometric variation of consumers. If extensive stoichiometric variation exists, it may help explain consumer variation in life-history strategy and fitness. To date, however, research on stoichiometric variation has focused on interspecific differences and assumed minimal intraspecific differences. Here this assumption is tested. Natural variation is quantified in body stoichiometry of two terrestrial insects: the generalist field cricket, Gryllus texensis Cade and Otte (Orthoptera: Gryllidae) and a specialist curculionid weevil, Sabinia setosa (Le Conte) (Coleoptera: Curculionidae). Both species exhibited extensive intraspecific stoichiometric variation. Cricket body nitrogen content ranged from 8–12% and there was a four-fold difference in body phosphorus content, ranging from 0.32–1.27%. Body size explained half this stoichiometric variation, with larger individuals containing less nitrogen and phosphorus. Weevils exhibited an almost three-fold difference in body phosphorus content, ranging from 0.38–0.97%. Overall, the variation observed within each of these species is comparable to the variation previously observed across almost all terrestrial insect species. PMID:20298114

  11. Vaporization chemistry of hypo-stoichiometric (U,Pu)O 2

    NASA Astrophysics Data System (ADS)

    Viswanathan, R.; Krishnaiah, M. V.

    2001-04-01

    Calculations were performed on hypo-stoichiometric uranium plutonium di-oxide to examine its vaporization behavior as a function of O/ M ( M= U+ Pu) ratio and plutonium content. The phase U (1- y) Pu yO z was treated as an ideal solid solution of (1- y)UO 2+ yPuO (2- x) such that x=(2- z)/ y. Oxygen potentials for different desired values of y, z, and temperature were used as the primary input to calculate the corresponding partial pressures of various O-, U-, and Pu-bearing gaseous species. Relevant thermodynamic data for the solid phases UO 2 and PuO (2- x) , and the gaseous species were taken from the literature. Total vapor pressure varies with O/M and goes through a minimum. This minimum does not indicate a congruently vaporizing composition. Vaporization behavior of this system can at best be quasi-congruent. Two quasi-congruently vaporizing compositions (QCVCs) exist, representing the equalities (O/M) vapor=(O/M) mixed-oxide and (U/Pu) vapor=(U/Pu) mixed-oxide, respectively. The (O/M) corresponding to QCVC1 is lower than that corresponding to QCVC2, but very close to the value where vapor pressure minimum occurs. The O/M values of both QCVCs increase with decrease in plutonium content. The vaporization chemistry of this system, on continuous vaporization under dynamic condition, is discussed.

  12. Environmental modeling of uranium interstitial compositions of non-stoichiometric oxides: experimental and theoretical analysis.

    PubMed

    Ivanova, Bojidarka

    2016-10-01

    Study of uranium interstitial compositions of non-stoichiometric oxides UO2+x (x ∈ 0.1-0.02) in gas and condense phases has been presented, using various soft-ionization mass spectrometric methods such as ESI-, APCI-, and MALDI-MS at a wide dynamic temperature gradient (∈ 25-300 °C). Linearly polarized vibrational spectroscopy has been utilized in order to assign unambiguously, the vibrational frequencies of uranium non-stoichiometric oxides. Experimental design has involved xUO2.66·yUO2.33, xUO2.66·yUO2.33/SiO2, xUO2.66·yUO2.33/SiO2 (NaOH) and SiO2/x'NaOH·y'UO2(NO3)2·6H2O, multicomponent systems (x = 1, y ∈ 0.1-1.0 and x' = 1, y' ∈ 0.1-0.6) as well as phase transitions UO2(NO3)2·6H2O → {U4O9(UO2.25)} → U3O7(UO2.33) → U3O8(UO2.66) → {UO3}, thus ensuring a maximal representativeness to real environmental conditions, where diverse chemical, geochemical and biochemical reactions, including complexation and sorption onto minerals have occurred. Experimental factors such as UV-irradiation, pH, temperature, concentration levels, solvent types and ion strength have been taken into consideration, too. As far as uranium speciation represents a challenging analytical task in terms of chemical identification diverse coordination species, mechanistic aspects relating incorporation of oxygen into UO 2+x form the shown full methods validation significantly impacts the field of environmental radioanalytical chemistry. UO2 is the most commonly used fuel in nuclear reactors around the globe; however, a large non-stoichiometric range ∈ UO1.65-UO2.25 has occurred due to radiolysis of water on UO2 surface yielding to H2O2, OH(·), and more. Each of those compositions has different oxygen diffusion. And in this respect enormous effort has been concentrated to study the potential impact of hazardous radionuclide on the environment, encompassing from the reprocessing to the disposal stages of the fuel waste, including the waste itself, the

  13. Carbon and nutrient use efficiencies optimally balance stoichiometric imbalances

    NASA Astrophysics Data System (ADS)

    Manzoni, Stefano; Čapek, Petr; Lindahl, Björn; Mooshammer, Maria; Richter, Andreas; Šantrůčková, Hana

    2016-04-01

    Decomposer organisms face large stoichiometric imbalances because their food is generally poor in nutrients compared to the decomposer cellular composition. The presence of excess carbon (C) requires adaptations to utilize nutrients effectively while disposing of or investing excess C. As food composition changes, these adaptations lead to variable C- and nutrient-use efficiencies (defined as the ratios of C and nutrients used for growth over the amounts consumed). For organisms to be ecologically competitive, these changes in efficiencies with resource stoichiometry have to balance advantages and disadvantages in an optimal way. We hypothesize that efficiencies are varied so that community growth rate is optimized along stoichiometric gradients of their resources. Building from previous theories, we predict that maximum growth is achieved when C and nutrients are co-limiting, so that the maximum C-use efficiency is reached, and nutrient release is minimized. This optimality principle is expected to be applicable across terrestrial-aquatic borders, to various elements, and at different trophic levels. While the growth rate maximization hypothesis has been evaluated for consumers and predators, in this contribution we test it for terrestrial and aquatic decomposers degrading resources across wide stoichiometry gradients. The optimality hypothesis predicts constant efficiencies at low substrate C:N and C:P, whereas above a stoichiometric threshold, C-use efficiency declines and nitrogen- and phosphorus-use efficiencies increase up to one. Thus, high resource C:N and C:P lead to low C-use efficiency, but effective retention of nitrogen and phosphorus. Predictions are broadly consistent with efficiency trends in decomposer communities across terrestrial and aquatic ecosystems.

  14. Non-stoichiometric mixed-phase titania photocatalyst

    DOEpatents

    Chen, Le [Lakewood, CO; Gray, Kimberly A [Evanston, IL; Graham, Michael E [Evanston, IL

    2012-06-19

    A mixed anatase-rutile phase, non-stoichiometric titania photocatalyst material is a highly reactive and is a UV and visible light responsive photocastalyst in the as-deposited condition (i.e. without the need for a subsequent thermal treatment). The mixed phase, non-stoichiometric titania thin film material is non-stoichiometric in terms of its oxygen content such that the thin film material shows a marked red-shift in photoresponse.

  15. Intrinsic point defects in off-stoichiometric Cu2ZnSnSe4: A neutron diffraction study

    NASA Astrophysics Data System (ADS)

    Gurieva, Galina; Valle Rios, Laura Elisa; Franz, Alexandra; Whitfield, Pamela; Schorr, Susan

    2018-04-01

    This work is an experimental study of intrinsic point defects in off-stoichiometric kesterite type CZTSe by means of neutron powder diffraction. We revealed the existence of copper vacancies (VCu), various cation anti site defects (CuZn, ZnCu, ZnSn, SnZn, and CuZn), as well as interstitials (Cui, Zni) in a wide range of off-stoichiometric polycrystalline powder samples synthesized by the solid state reaction. The results show that the point defects present in off-stoichiometric CZTSe agree with the off-stoichiometry type model, assuming certain cation substitutions accounting for charge balance. In addition to the known off-stoichiometry types A-H, new types (I-L) have been introduced. For the very first time, a correlation between the chemical composition of the CZTSe kesterite type phase and the occurring intrinsic point defects is presented. In addition to the off-stoichiometry type specific defects, the Cu/Zn disorder is always present in the CZTSe phase. In Cu-poor/Zn-rich CZTSe, a composition considered as the one that delivers the best photovoltaic performance, mainly copper vacancies, ZnCu and ZnSn anti sites are present. Also, this compositional region shows the lowest degree of Cu/Zn disorder.

  16. Finite element stress analysis of idealized composite damage zones

    NASA Technical Reports Server (NTRS)

    Obrien, D.; Herakovich, C. T.

    1978-01-01

    A quasi three dimensional finite element stress analysis of idealized damage zones in composite laminates is presented. The damage zones consist of a long centered groove or cutout extending one or two layers in depth from both top and bottom surfaces of a thin composite laminate. Elastic results are presented for compressive loading of four and eight layer laminates. It is shown that a boundary layer exists near the cutout edge similar to that previously shown to exist along free edges. The cutout is shown to produce significant interlaminar stresses in the interior of the laminate away from free cutout edges. The interlaminar stresses are also shown to contribute to failure which is defined using the Tsai-Wu failure criteria.

  17. Thermodynamics of aragonite-strontianite solid solutions: Results from stoichiometric solubility at 25 and 76°C

    USGS Publications Warehouse

    Plummer, Niel; Busenberg, E.

    1987-01-01

    Neither equilibrium nor stoichiometric saturation is observed at 76°C during laboratory recrystallization of strontianite-aragonite solid solutions even after apparent 100 percent conversion to a narrow secondary composition and demonstration of a nearly constant composition system for periods of 300 hours.

  18. A model for the compositions of non-stoichiometric intermediate phases formed by diffusion reactions, and its application to Nb 3Sn superconductors

    DOE PAGES

    Xu, X.; Sumption, M. D.

    2016-01-12

    In this work we explore the compositions of non-stoichiometric intermediate phases formed by diffusion reactions: a mathematical framework is developed and tested against the specific case of Nb 3Sn superconductors. In the first part, the governing equations for the bulk diffusion and interphase interface reactions during the growth of a compound are derived, numerical solutions to which give both the composition profile and growth rate of the compound layer. The analytic solutions are obtained with certain approximations made. In the second part, we explain an effect that the composition characteristics of compounds can be quite different depending on whether itmore » is the bulk diffusion or grain boundary diffusion that dominates in the compounds, and that “frozen” bulk diffusion leads to unique composition characteristics that the bulk composition of a compound layer remains unchanged after its initial formation instead of varying with the diffusion reaction system; here the model is modified for the case of grain boundary diffusion. Lastly, we apply this model to the Nb 3Sn superconductors and propose approaches to control their compositions.« less

  19. Ultra-hard AlMgB14 coatings fabricated by RF magnetron sputtering from a stoichiometric target

    NASA Astrophysics Data System (ADS)

    Grishin, A. M.; Khartsev, S. I.; Böhlmark, J.; Ahlgren, M.

    2015-01-01

    For the first time hard aluminum magnesium boride films were fabricated by RF magnetron sputtering from a single stoichiometric ceramic AlMgB14 target. Optimized processing conditions (substrate temperature, target sputtering power and target-to-substrate distance) enable fabrication of stoichiometric in-depth compositionally homogeneous films with the peak values of nanohardness 88 GPa and Young's modulus 517 GPa at the penetration depth of 26 nm and, respectively, 35 and 275 GPa at 200 nm depth in 2 μm thick film.

  20. Effect of compositional heterogeneity on dissolution of non-ideal LNAPL mixtures

    NASA Astrophysics Data System (ADS)

    Vasudevan, M.; Johnston, C. D.; Bastow, T. P.; Lekmine, G.; Rayner, J. L.; Nambi, I. M.; Suresh Kumar, G.; Ravi Krishna, R.; Davis, G. B.

    2016-11-01

    The extent of dissolution of petroleum hydrocarbon fuels into groundwater depends greatly on fuel composition. Petroleum fuels can consist of thousands of compounds creating different interactions within the non-aqueous phase liquid (NAPL), thereby affecting the relative dissolution of the components and hence a groundwater plume's composition over long periods. Laboratory experiments were conducted to study the variability in the effective solubilities and activity coefficients for common constituents of gasoline fuels (benzene, toluene, p-xylene and 1,2,4-trimethylbenzene) (BTX) in matrices with an extreme range of molar volumes and chemical affinities. Four synthetic mixtures were investigated comprising BTX with the bulk of the NAPL mixtures made up of either, ethylbenzene (an aromatic like BTX with similar molar volume); 1,3,5-trimethylbenzene (an aromatic with a greater molar volume); n-hexane (an aliphatic with a low molar volume); and n-decane (an aliphatic with a high molar volume). Equilibrium solubility values for the constituents were under-predicted by Raoult's law by up to 30% (higher experimental concentrations) for the mixture with n-hexane as a filler and over-predicted by up to 12% (lower experimental concentrations) for the aromatic mixtures with ethylbenzene and 1,3,5-trimethylbenzene as fillers. Application of PP-LFER (poly-parameter linear free energy relationship) model for non-ideal mixtures also resulted in poor correlation between experimentally measured and predicted concentrations, indicating that differences in chemical affinities can be the major cause of deviation from ideal behavior. Synthetic mixtures were compared with the dissolution behavior of fresh and naturally weathered unleaded gasoline. The presence of lighter aliphatic components in the gasoline had a profound effect on estimating effective solubility due to chemical affinity differences (estimated at 0.0055 per percentage increase in the molar proportion of aliphatic) as

  1. A stoichiometric calibration method for dual energy computed tomography

    NASA Astrophysics Data System (ADS)

    Bourque, Alexandra E.; Carrier, Jean-François; Bouchard, Hugo

    2014-04-01

    The accuracy of radiotherapy dose calculation relies crucially on patient composition data. The computed tomography (CT) calibration methods based on the stoichiometric calibration of Schneider et al (1996 Phys. Med. Biol. 41 111-24) are the most reliable to determine electron density (ED) with commercial single energy CT scanners. Along with the recent developments in dual energy CT (DECT) commercial scanners, several methods were published to determine ED and the effective atomic number (EAN) for polyenergetic beams without the need for CT calibration curves. This paper intends to show that with a rigorous definition of the EAN, the stoichiometric calibration method can be successfully adapted to DECT with significant accuracy improvements with respect to the literature without the need for spectrum measurements or empirical beam hardening corrections. Using a theoretical framework of ICRP human tissue compositions and the XCOM photon cross sections database, the revised stoichiometric calibration method yields Hounsfield unit (HU) predictions within less than ±1.3 HU of the theoretical HU calculated from XCOM data averaged over the spectra used (e.g., 80 kVp, 100 kVp, 140 kVp and 140/Sn kVp). A fit of mean excitation energy (I-value) data as a function of EAN is provided in order to determine the ion stopping power of human tissues from ED-EAN measurements. Analysis of the calibration phantom measurements with the Siemens SOMATOM Definition Flash dual source CT scanner shows that the present formalism yields mean absolute errors of (0.3 ± 0.4)% and (1.6 ± 2.0)% on ED and EAN, respectively. For ion therapy, the mean absolute errors for calibrated I-values and proton stopping powers (216 MeV) are (4.1 ± 2.7)% and (0.5 ± 0.4)%, respectively. In all clinical situations studied, the uncertainties in ion ranges in water for therapeutic energies are found to be less than 1.3 mm, 0.7 mm and 0.5 mm for protons, helium and carbon ions respectively, using a generic

  2. Oxygen chemical diffusion in hypo-stoichiometric MOX

    NASA Astrophysics Data System (ADS)

    Kato, Masato; Morimoto, Kyoichi; Tamura, Tetsuya; Sunaoshi, Takeo; Konashi, Kenji; Aono, Shigenori; Kashimura, Motoaki

    2009-06-01

    Kinetics of the oxygen-to-metal ratio change in (U 0.8Pu 0.2)O 2-x and (U 0.7Pu 0.3)O 2-x was evaluated in the temperature range of 1523-1623 K using a thermo-gravimetric technique. The oxygen chemical diffusion coefficients were decided as a function of temperature from the kinetics of the reduction process under a hypo-stoichiometric composition. The diffusion coefficient of (U 0.7Pu 0.3)O 2-x was smaller than that of (U 0.8Pu 0.2)O 2-x. No strong dependence was observed for the diffusion coefficient on the O/M variation of samples.

  3. Self-assembly of Carbon Vacancies in Sub-stoichiometric ZrC1−x

    PubMed Central

    Zhang, Yanhui; Liu, Bin; Wang, Jingyang

    2015-01-01

    Sub-stoichiometric interstitial compounds, including binary transition metal carbides (MC1−x), maintain structural stability even if they accommodate abundant anion vacancies. This unique character endows them with variable-composition, diverse-configuration and controllable-performance through composition and structure design. Herein, the evolution of carbon vacancy (VC) configuration in sub-stoichiometric ZrC1−x is investigated by combining the cluster expansion method and first-principles calculations. We report the interesting self-assembly of VCs and the fingerprint VC configuration (VC triplet constructed by 3rd nearest neighboring vacancies) in all the low energy structures of ZrC1−x. When VC concentration is higher than the critical value of 0.5 (x > 0.5), the 2nd nearest neighboring VC configurations with strongly repulsive interaction inevitably appear, and meanwhile, the system energy (or formation enthalpy) of ZrC1−x increases sharply which suggests the material may lose phase stability. The present results clarify why ZrC1−x bears a huge amount of VCs, tends towards VC ordering, and retains stability up to a stoichiometry of x = 0.5. PMID:26667083

  4. Advantage of low-temperature hydrothermal synthesis to grow stoichiometric crednerite crystals

    NASA Astrophysics Data System (ADS)

    Poienar, Maria; Martin, Christine; Lebedev, Oleg I.; Maignan, Antoine

    2018-06-01

    This work reports a new approach for the growth of stoichiometric crednerite CuMnO2 crystals. The hydrothermal reaction, starting from soluble metal sulphates as precursors, is assisted by ethylene glycol and the formation of crednerite is found to depend strongly on pH and temperature. This method allows obtaining small hexagonal platelets with the larger dimension about 1.0-1.5 μm and with a composition characterized by a Cu/Mn ratio of 1. Thus, these crystals differ from the needle-like millimetric ones obtained by the flux technique for which the composition departs from the expected one and is close to Cu1.04Mn0.96. This monitoring of the cationic composition in crednerite, using hydrothermal synthesis, is important as the Cu/Mn ratio controls the low temperature antiferromagnetic ground-state.

  5. Idealized vs. Realistic Microstructures: An Atomistic Simulation Case Study on γ/γ' Microstructures.

    PubMed

    Prakash, Aruna; Bitzek, Erik

    2017-01-23

    Single-crystal Ni-base superalloys, consisting of a two-phase γ / γ ' microstructure, retain high strengths at elevated temperatures and are key materials for high temperature applications, like, e.g., turbine blades of aircraft engines. The lattice misfit between the γ and γ ' phases results in internal stresses, which significantly influence the deformation and creep behavior of the material. Large-scale atomistic simulations that are often used to enhance our understanding of the deformation mechanisms in such materials must accurately account for such misfit stresses. In this work, we compare the internal stresses in both idealized and experimentally-informed, i.e., more realistic, γ / γ ' microstructures. The idealized samples are generated by assuming, as is frequently done, a periodic arrangement of cube-shaped γ ' particles with planar γ / γ ' interfaces. The experimentally-informed samples are generated from two different sources to produce three different samples-the scanning electron microscopy micrograph-informed quasi-2D atomistic sample and atom probe tomography-informed stoichiometric and non-stoichiometric atomistic samples. Additionally, we compare the stress state of an idealized embedded cube microstructure with finite element simulations incorporating 3D periodic boundary conditions. Subsequently, we study the influence of the resulting stress state on the evolution of dislocation loops in the different samples. The results show that the stresses in the atomistic and finite element simulations are almost identical. Furthermore, quasi-2D boundary conditions lead to a significantly different stress state and, consequently, different evolution of the dislocation loop, when compared to samples with fully 3D boundary conditions.

  6. Trophic and stoichiometric consequences of nutrification for the intertidal tropical zoanthid Zoanthus sociatus.

    PubMed

    Leal, Miguel C; Rocha, Rui J M; Anaya-Rojas, Jaime M; Cruz, Igor C S; Ferrier-Pagès, Christine

    2017-06-15

    Zoanthids are conspicuous and abundant members of intertidal environments, where they are exposed to large environmental fluctuations and subject to increasing loads of anthropogenic nutrients. Here we assess the trophic ecology and stoichiometric consequences of nutrient loading for symbiotic zoanthids inhabiting different intertidal habitats. More specifically, we analysed the stable isotope signature (δ 13 C and δ 15 N), elemental composition (C, N and P) and stoichiometry (C:N, C:P, N:P) of Zoanthus sociatus differently exposed to nutrification. Results suggest that autotrophy is the main feeding mode of zoanthids and that the effect water nutrient content differently affects the elemental phenotype of zoanthids depending on tidal habitat. Additionally, habitat effects on Z. sociatus P-related stoichiometric traits highlight functional differences likely associated with variation in Symbiodinium density. These findings provide an innovative approach to assess how cnidarian-dinoflagellate symbioses response to ecosystem changes in environmentally dynamic reef flats, particularly nutrient loading. Copyright © 2017 Elsevier Ltd. All rights reserved.

  7. Atomically Precise Interfaces from Non-stoichiometric Deposition

    NASA Astrophysics Data System (ADS)

    Nie, Yuefeng; Zhu, Ye; Lee, Che-Hui; Kourkoutis, Lena; Mundy, Julia; Junquera, Javier; Ghosez, Philippe; Baek, David; Sung, Suk Hyun; Xi, Xiaoxing; Shen, Kyle; Muller, David; Schlom, Darrell

    2015-03-01

    Complex oxide heterostructures display some of the most chemically abrupt, atomically precise interfaces, which is advantageous when constructing new interface phases with emergent properties by juxtaposing incompatible ground states. One might assume that atomically precise interfaces result from stoichiometric growth. Here we show that the most precise control is, however, obtained by using deliberate and specific non-stoichiometric growth conditions. For the precise growth of Srn+1TinO3n+1 Ruddlesden-Popper (RP) phases, stoichiometric deposition leads to the loss of the first RP rock-salt double layer, but growing with a strontium-rich surface layer restores the bulk stoichiometry and ordering of the subsurface RP structure. Our results dramatically expand the materials that can be prepared in epitaxial heterostructures with precise interface control--from just the n = 1 end members (perovskites) to the entire RP homologous series--enabling the exploration of novel quantum phenomena at a richer variety of oxide interfaces.

  8. Atomically precise interfaces from non-stoichiometric deposition

    NASA Astrophysics Data System (ADS)

    Nie, Y. F.; Zhu, Y.; Lee, C.-H.; Kourkoutis, L. F.; Mundy, J. A.; Junquera, J.; Ghosez, Ph.; Baek, D. J.; Sung, S.; Xi, X. X.; Shen, K. M.; Muller, D. A.; Schlom, D. G.

    2014-08-01

    Complex oxide heterostructures display some of the most chemically abrupt, atomically precise interfaces, which is advantageous when constructing new interface phases with emergent properties by juxtaposing incompatible ground states. One might assume that atomically precise interfaces result from stoichiometric growth. Here we show that the most precise control is, however, obtained by using deliberate and specific non-stoichiometric growth conditions. For the precise growth of Srn+1TinOn+1 Ruddlesden-Popper (RP) phases, stoichiometric deposition leads to the loss of the first RP rock-salt double layer, but growing with a strontium-rich surface layer restores the bulk stoichiometry and ordering of the subsurface RP structure. Our results dramatically expand the materials that can be prepared in epitaxial heterostructures with precise interface control—from just the n=∞ end members (perovskites) to the entire RP homologous series—enabling the exploration of novel quantum phenomena at a richer variety of oxide interfaces.

  9. Idealized vs. Realistic Microstructures: An Atomistic Simulation Case Study on γ/γ′ Microstructures

    PubMed Central

    Prakash, Aruna; Bitzek, Erik

    2017-01-01

    Single-crystal Ni-base superalloys, consisting of a two-phase γ/γ′ microstructure, retain high strengths at elevated temperatures and are key materials for high temperature applications, like, e.g., turbine blades of aircraft engines. The lattice misfit between the γ and γ′ phases results in internal stresses, which significantly influence the deformation and creep behavior of the material. Large-scale atomistic simulations that are often used to enhance our understanding of the deformation mechanisms in such materials must accurately account for such misfit stresses. In this work, we compare the internal stresses in both idealized and experimentally-informed, i.e., more realistic, γ/γ′ microstructures. The idealized samples are generated by assuming, as is frequently done, a periodic arrangement of cube-shaped γ′ particles with planar γ/γ′ interfaces. The experimentally-informed samples are generated from two different sources to produce three different samples—the scanning electron microscopy micrograph-informed quasi-2D atomistic sample and atom probe tomography-informed stoichiometric and non-stoichiometric atomistic samples. Additionally, we compare the stress state of an idealized embedded cube microstructure with finite element simulations incorporating 3D periodic boundary conditions. Subsequently, we study the influence of the resulting stress state on the evolution of dislocation loops in the different samples. The results show that the stresses in the atomistic and finite element simulations are almost identical. Furthermore, quasi-2D boundary conditions lead to a significantly different stress state and, consequently, different evolution of the dislocation loop, when compared to samples with fully 3D boundary conditions. PMID:28772453

  10. Ex vivo validation of a stoichiometric dual energy CT proton stopping power ratio calibration

    NASA Astrophysics Data System (ADS)

    Xie, Yunhe; Ainsley, Christopher; Yin, Lingshu; Zou, Wei; McDonough, James; Solberg, Timothy D.; Lin, Alexander; Teo, Boon-Keng Kevin

    2018-03-01

    A major source of uncertainty in proton therapy is the conversion of Hounsfield unit (HU) to proton stopping power ratio relative to water (SPR). In this study, we measured and quantified the accuracy of a stoichiometric dual energy CT (DECT) SPR calibration. We applied a stoichiometric DECT calibration method to derive the SPR using CT images acquired sequentially at 80 kVp and 140 kVp . The dual energy index was derived based on the HUs of the paired spectral images and used to calculate the effective atomic number (Z eff), relative electron density ({{ρ }e} ), and SPRs of phantom and biological materials. Two methods were used to verify the derived SPRs. The first method measured the sample’s water equivalent thicknesses to deduce the SPRs using a multi-layer ion chamber (MLIC) device. The second method utilized Gafchromic EBT3 film to directly compare relative ranges between sample and water after proton pencil beam irradiation. Ex vivo validation was performed using five different types of frozen animal tissues with the MLIC and three types of fresh animal tissues using film. In addition, the residual ranges recorded on the film were used to compare with those from the treatment planning system using both DECT and SECT derived SPRs. Bland-Altman analysis indicates that the differences between DECT and SPR measurement of tissue surrogates, frozen and fresh animal tissues has a mean of 0.07% and standard deviation of 0.58% compared to 0.55% and 1.94% respectively for single energy CT (SECT) and SPR measurement. Our ex vivo study indicates that the stoichiometric DECT SPR calibration method has the potential to be more accurate than SECT calibration under ideal conditions although beam hardening effects and other image artifacts may increase this uncertainty.

  11. Flash sintering of stoichiometric and hyper-stoichiometric urania

    DOE PAGES

    Valdez, James Anthony; Byler, Darrin David; Kardoulaki, Erofili; ...

    2018-03-29

    Flash sintering (FS), a novel fabrication technique belonging to the family of field assisted sintering (FAS) techniques, has been utilized in this study to fabricate uranium dioxide (UO 2) pellets. Stoichiometric (UO 2.00) and hyper-stoichiometric (UO 2.16) pellets were flash sintered at 600 °C within a few (2–3) minutes. This is in sharp contrast to conventional sintering where temperatures hundreds of degrees higher are necessary and the sintering time extends to hours. Relating this in terms of the homologous temperature ratio (T H) for both conditions shows that in the case of flash sintering at 600 °C, T H =more » 0.3 versus T H = 0.6 for conventional sintering at 1600 °C. The highest density achieved for a UO 2.00 pellet was 81% theoretical density (TD) when flash sintered at 600 °C for 184 s at a field of 188 V/cm and a current density of 442 mA/mm 2. For the UO 2.16 pellet, the highest achieved density was 92% TD when flash sintered at 600 °C for 140 s at a field of 188 V/cm and a current density of 632 mA/mm 2. X-ray diffraction (XRD) characterization of the sintered pellets showed the final sintered material to be single cubic fluorite phase. Scanning electron microscopy (SEM) of longitudinal sections revealed non-uniform microstructures with regions of high density where the grain size ranged from 1 to 15 μm. Comparisons between conventionally and flash sintered pellets that achieved equivalent shrinkage strains were also conducted. Lastly, in all cases, the flash sintered pellets achieved similar densification to the conventionally sintered pellets at much lower furnace temperatures and shorter times.« less

  12. Flash sintering of stoichiometric and hyper-stoichiometric urania

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Valdez, James Anthony; Byler, Darrin David; Kardoulaki, Erofili

    Flash sintering (FS), a novel fabrication technique belonging to the family of field assisted sintering (FAS) techniques, has been utilized in this study to fabricate uranium dioxide (UO 2) pellets. Stoichiometric (UO 2.00) and hyper-stoichiometric (UO 2.16) pellets were flash sintered at 600 °C within a few (2–3) minutes. This is in sharp contrast to conventional sintering where temperatures hundreds of degrees higher are necessary and the sintering time extends to hours. Relating this in terms of the homologous temperature ratio (T H) for both conditions shows that in the case of flash sintering at 600 °C, T H =more » 0.3 versus T H = 0.6 for conventional sintering at 1600 °C. The highest density achieved for a UO 2.00 pellet was 81% theoretical density (TD) when flash sintered at 600 °C for 184 s at a field of 188 V/cm and a current density of 442 mA/mm 2. For the UO 2.16 pellet, the highest achieved density was 92% TD when flash sintered at 600 °C for 140 s at a field of 188 V/cm and a current density of 632 mA/mm 2. X-ray diffraction (XRD) characterization of the sintered pellets showed the final sintered material to be single cubic fluorite phase. Scanning electron microscopy (SEM) of longitudinal sections revealed non-uniform microstructures with regions of high density where the grain size ranged from 1 to 15 μm. Comparisons between conventionally and flash sintered pellets that achieved equivalent shrinkage strains were also conducted. Lastly, in all cases, the flash sintered pellets achieved similar densification to the conventionally sintered pellets at much lower furnace temperatures and shorter times.« less

  13. Flash sintering of stoichiometric and hyper-stoichiometric urania

    NASA Astrophysics Data System (ADS)

    Valdez, J. A.; Byler, D. D.; Kardoulaki, E.; Francis, J. S. C.; McClellan, K. J.

    2018-07-01

    Flash sintering (FS), a novel fabrication technique belonging to the family of field assisted sintering (FAS) techniques, has been utilized in this study to fabricate uranium dioxide (UO2) pellets. Stoichiometric (UO2.00) and hyper-stoichiometric (UO2.16) pellets were flash sintered at 600 °C within a few (2-3) minutes. This is in sharp contrast to conventional sintering where temperatures hundreds of degrees higher are necessary and the sintering time extends to hours. Relating this in terms of the homologous temperature ratio (TH) for both conditions shows that in the case of flash sintering at 600 °C, TH = 0.3 versus TH = 0.6 for conventional sintering at 1600 °C. The highest density achieved for a UO2.00 pellet was 81% theoretical density (TD) when flash sintered at 600 °C for 185 s at a field of 188 V/cm and a current density of 442 mA/mm2. For the UO2.16 pellet, the highest achieved density was 91% TD when flash sintered at 600 °C for 123 s at a field of 188 V/cm and a current density of 632 mA/mm2. X-ray diffraction (XRD) characterization of the sintered pellets showed the final sintered material to be single cubic fluorite phase. Scanning electron microscopy (SEM) of longitudinal sections revealed non-uniform microstructures with regions of high density where the grain size ranged from 1 to 15 μm. Comparisons between conventionally and flash sintered pellets that achieved equivalent shrinkage strains were also conducted. In all cases, the flash sintered pellets achieved similar densification to the conventionally sintered pellets at much lower furnace temperatures and shorter times.

  14. THE FORMATION OF DETONATION IN SATURATED MIXTURES OF KNALLGAS-STEAM AND IN STOICHIOMETRIC MIXTURES OF DEUTERIUM-OXYGEN (HEAVY WATER). Final Report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Luker, J.A.; Adler, L.B.; Hobaica, E.C.

    1959-01-23

    The purpose of this investigation was to determine the reaction characteristics of satuated mixtures of knall gas (stoichiometric mixture of hydrogen and oxygen) --steam and mixtures of heavy knall gas (stoichm-ometric mixture of deuterion and oxygen) saturated with heavy water. These mixtues were studied experimentally over composition ranges from no reaction limit to enriched compositions which supported detonations. (auth)

  15. Non-stoichiometric AB5 alloys for metal hydride electrodes

    DOEpatents

    Reilly, James J.; Adzic, Gordana D.; Johnson, John R.; Vogt, Thomas; McBreen, James

    2001-01-01

    The present invention provides a non-stoichiometric alloy comprising a composition having the formula AB.sub.5+X an atomic ratio wherein A is selected from the group consisting of the rare earth metals, yttrium, mischmetal, or a combination thereof; B is nickel and tin, or nickel and tin and at least a third element selected from the group consisting of the elements in group IVA of the periodic table, aluminum, manganese, iron, cobalt, copper, antimony or a combination thereof; X is greater than 0 and less than or equal to about 2.0; and wherein at least one substituted A site is occupied by at least one of the B elements. An electrode incorporating said alloy and an electrochemical cell incorporating said electrode are also described.

  16. Study of non-stoichiometric BaSrTiFeO3 oxide dedicated to semiconductor gas sensors

    NASA Astrophysics Data System (ADS)

    Fasquelle, D.; Verbrugghe, N.; Deputier, S.

    2016-11-01

    Developing instrumentation systems compatible with the European RoHS directive (restriction of hazardous substances) to monitor our environment is of great interest for our society. Our research therefore aims at developing innovating integrated systems of detection dedicated to the characterization of various environmental exposures. These systems, which integrate new gas sensors containing lead-free oxides, are dedicated to the detection of flammable and toxic gases. We have firstly chosen to study semiconductor gas sensors implemented with lead-free oxides in view to develop RoHS devices. Therefore thick films deposited by spin-coating and screen-printing have been chosen for their robustness, ease to realize and ease to finally obtain cost-effective sensors. As crystalline defects and ionic vacancies are of great interest for gas detection, we have decided to study a non-stoichiometric composition of the BaSrTiFeO3 sensible oxide. Nonstoichiometric BaSrTiFeO3 lead-free oxide thick films were deposited by screen-printing on polycrystalline AFO3 substrates covered by a layer of Ag-Pd acting as bottom electrode. The physical characterizations have revealed a crystalline structure mainly composed of BaTiO3 pseudo-cubic phase and Ba4Ti12O27 monoclinic phase for the powder, and a porous microstructure for the thick films. When compared to a BSTF thick film with a stoichiometric composition, a notable increase in the BSTF dielectric constant value was observed when taking into account of a similar microstructure and grain size. The loss tangent mean value varies more softly for the non-stoichiometric BaSrTiFeO3 films than for the perovskite BSTF film as tanδ decreases from 0.45 to 0.04 when the frequency increases from 100 Hz to 1 MHz.

  17. High efficiency stoichiometric internal combustion engine system

    DOEpatents

    Winsor, Richard Edward; Chase, Scott Allen

    2009-06-02

    A power system including a stoichiometric compression ignition engine in which a roots blower is positioned in the air intake for the engine to control air flow. Air flow is decreased during part power conditions to maintain the air-fuel ratio in the combustion chamber of the engine at stoichiometric, thus enabling the use of inexpensive three-way catalyst to reduce oxides of nitrogen. The roots blower is connected to a motor generator so that when air flow is reduced, electrical energy is stored which is made available either to the roots blower to temporarily increase air flow or to the system electrical load and thus recapture energy that would otherwise be lost in reducing air flow.

  18. Magnetic moment distribution modeling in non stoichiometric Ni-Mn-Ga ferromagnetic shape memory alloys

    NASA Astrophysics Data System (ADS)

    Lázpita, P.; Gutiérrez, J.; Barandiarán, J. M.; Chernenko, V. A.; Mondelli, C.; Chapon, L.

    2014-11-01

    Neutron polarized diffraction technique has been used to elucidate the magnetic moment distribution density in non stoichiometric Ni—Mn—Ga single crystals. These experiments allow us to determine a localized magnetic moment in the Mn position in the austenitic phase, and to validity qualitatively previous models of magnetic distributions where there are antiferromagnetic and ferromagnetic coupling for Mn atoms that are sited out of their properly positions. This measurements show the deep dependence of the magnetic moment with the composition and the atomic order.

  19. Eco-Stoichiometric Alterations in Paddy Soil Ecosystem Driven by Phosphorus Application

    PubMed Central

    Li, Xia; Wang, Hang; Gan, ShaoHua; Jiang, DaQian; Tian, GuangMing; Zhang, ZhiJian

    2013-01-01

    Agricultural fertilization may change processes of elemental biogeochemical cycles and alter the ecological function. Ecoenzymatic stoichiometric feature plays a critical role in global soil carbon (C) metabolism, driving element cycles, and mediating atmospheric composition in response to agricultural nutrient management. Despite the importance on crop growth, the role of phosphorous (P) in compliance with eco-stoichiometry on soil C and nitrogen (N) sequestration in the paddy field remains poorly understood in the context of climate change. Here, we collected soil samples from a field experiment after 6 years of chemical P application at a gradient of 0 (P-0), 30 (P-30), 60 (P-60), and 90 (P-90) kg ha−1 in order to evaluate the role of P on stoichiometric properties in terms of soil chemical, microbial biomass, and eco-enzyme activities as well as greenhouse gas (GHG: CO2, N2O and CH4) emissions. Continuous P input increased soil total organic C and N by 1.3–9.2% and 3%–13%, respectively. P input induced C and N limitations as indicated by the decreased ratio of C:P and N:P in the soil and microbial biomass. A synergistic mechanism among the ecoenzymatic stoichiometry, which regulated the ecological function of microbial C and N acquisition and were stoichiometrically related to P input, stimulated soil C and N sequestration in the paddy field. The lower emissions of N2O and CH4 under the higher P application (P-60 and P-90) in July and the insignificant difference in N2O emission in August compared to P-30; however, continuous P input enhanced CO2 fluxes for both samplings. There is a technical conflict for simultaneously regulating three types of GHGs in terms of the eco-stoichiometry mechanism under P fertilization. Thus, it is recommended that the P input in paddy fields not exceed 60 kg ha−1 may maximize soil C sequestration, minimize P export, and guarantee grain yields. PMID:23667435

  20. GPU-based simulations of fracture in idealized brick and mortar composites

    NASA Astrophysics Data System (ADS)

    William Pro, J.; Kwei Lim, Rone; Petzold, Linda R.; Utz, Marcel; Begley, Matthew R.

    2015-07-01

    Stiff ceramic platelets (or bricks) that are aligned and bonded to a second ductile phase with low volume fraction (mortar) are a promising pathway to produce stiff, high-toughness composites. For certain ranges of constituent properties, including those of some synthetic analogs to nacre, one can demonstrate that the deformation is dominated by relative brick motions. This paper describes simulations of fracture that explicitly track the motions of individual rigid bricks in an idealized microstructure; cohesive tractions acting between the bricks introduce elastic, plastic and rupture behaviors. Results are presented for the stresses and damage near macroscopic cracks with different brick orientations relative to the loading orientation. The anisotropic macroscopic initiation toughness is computed for small-scale yielding conditions and is shown to be independent of specimen geometry and loading configuration. The results are shown to be in agreement with previously published experiments on synthetic nacre.

  1. Application of a data reconciliation method to the stoichiometric analysis of Fibrobacter succinogenes growth.

    PubMed

    Guiavarch, Erell; Pons, Agnes; Creuly, Catherine; Dussap, Claude-Gilles

    2008-12-01

    Fibrobacter succinogenes S85, a strictly anaerobic Gram-negative bacterium, was grown in continuous culture in a bioreactor at different dilution rates (0.02 to 0.092 h(-1)) on a fully synthetic culture medium with glucose as carbon source. Glucose and ammonium sulfate consumption, as well as biomass, succinate, acetate, formate, and carbohydrate production were regularly measured. The relevant biomass elemental compositions were established for each dilution rate. Robustness of the experimental information was checked by C and N mass balances estimation, which were satisfactory. A detailed overall stoichiometry analysis of the process, including all substrates and products of the culture, was proposed. Online and off-line parameters measured during the culture brought a large number of data which were weighted by their respective variance associated to the measured value. The material balance resulted in an overdetermined linear system of equations made of weighted relationships including experimental data, elemental balances (C, H, O, N, S, Na), and an additional constraint. The mass balances involved in stoichiometric equations were solved using data reconciliation and linear algebra methods to take into account error measurements. This methodology allowed to establish the overall stoichiometric equation for each dilution rate studied.

  2. Concepts of Ideal and Nonideal Explosives.

    DTIC Science & Technology

    1981-12-01

    Akst and J. Hershkowitz, "Explosive Performance Modification by Cosolidifaction of Ammonium Nitrate with Fuels ," Technical Report 4987, Picatinny...explosives Equations of state Diameter effect Ammonium nitrate 20. ASSrRACr (ca’mes r w re t N netwezy ad identity by block number) The purpose of...this report is to stimulate discussion on the nonideality of ammonium nitrate and its composite explosives. The concept of ideal and non- ideal

  3. Thermodynamic assessment of oxygen diffusion in non-stoichiometric UO2±x from experimental data and Frenkel pair modeling

    NASA Astrophysics Data System (ADS)

    Berthinier, C.; Rado, C.; Chatillon, C.; Hodaj, F.

    2013-02-01

    The self and chemical diffusion of oxygen in the non-stoichiometric domain of the UO2 compound is analyzed from the point of view of experimental determinations and modeling from Frenkel pair defects. The correlation between the self-diffusion and the chemical diffusion coefficients is analyzed using the Darken coefficient calculated from a thermodynamic description of the UO2±x phase. This description was obtained from an optimization of thermodynamic and phase diagram data and modeling with different point defects, including the Frenkel pair point defects. The proposed diffusion coefficients correspond to the 300-2300 K temperature range and to the full composition range of the non stoichiometric UO2 compound. These values will be used for the simulation of the oxidation and ignition of the uranium carbide in different oxygen atmospheres that starts at temperatures as low as 400 K.

  4. A formulation of tissue- and water-equivalent materials using the stoichiometric analysis method for CT-number calibration in radiotherapy treatment planning.

    PubMed

    Yohannes, Indra; Kolditz, Daniel; Langner, Oliver; Kalender, Willi A

    2012-03-07

    Tissue- and water-equivalent materials (TEMs) are widely used in quality assurance and calibration procedures, both in radiodiagnostics and radiotherapy. In radiotherapy, particularly, the TEMs are often used for computed tomography (CT) number calibration in treatment planning systems. However, currently available TEMs may not be very accurate in the determination of the calibration curves due to their limitation in mimicking radiation characteristics of the corresponding real tissues in both low- and high-energy ranges. Therefore, we are proposing a new formulation of TEMs using a stoichiometric analysis method to obtain TEMs for the calibration purposes. We combined the stoichiometric calibration and the basic data method to compose base materials to develop TEMs matching standard real tissues from ICRU Report 44 and 46. First, the CT numbers of six materials with known elemental compositions were measured to get constants for the stoichiometric calibration. The results of the stoichiometric calibration were used together with the basic data method to formulate new TEMs. These new TEMs were scanned to validate their CT numbers. The electron density and the stopping power calibration curves were also generated. The absolute differences of the measured CT numbers of the new TEMs were less than 4 HU for the soft tissues and less than 22 HU for the bone compared to the ICRU real tissues. Furthermore, the calculated relative electron density and electron and proton stopping powers of the new TEMs differed by less than 2% from the corresponding ICRU real tissues. The new TEMs which were formulated using the proposed technique increase the simplicity of the calibration process and preserve the accuracy of the stoichiometric calibration simultaneously.

  5. Soft sensor based composition estimation and controller design for an ideal reactive distillation column.

    PubMed

    Vijaya Raghavan, S R; Radhakrishnan, T K; Srinivasan, K

    2011-01-01

    In this research work, the authors have presented the design and implementation of a recurrent neural network (RNN) based inferential state estimation scheme for an ideal reactive distillation column. Decentralized PI controllers are designed and implemented. The reactive distillation process is controlled by controlling the composition which has been estimated from the available temperature measurements using a type of RNN called Time Delayed Neural Network (TDNN). The performance of the RNN based state estimation scheme under both open loop and closed loop have been compared with a standard Extended Kalman filter (EKF) and a Feed forward Neural Network (FNN). The online training/correction has been done for both RNN and FNN schemes for every ten minutes whenever new un-trained measurements are available from a conventional composition analyzer. The performance of RNN shows better state estimation capability as compared to other state estimation schemes in terms of qualitative and quantitative performance indices. Copyright © 2010 ISA. Published by Elsevier Ltd. All rights reserved.

  6. Raman analysis of non stoichiometric Ni1-δO

    NASA Astrophysics Data System (ADS)

    Dubey, Paras; Choudhary, K. K.; Kaurav, Netram

    2018-04-01

    Thermal decomposition method was used to synthesize non-stoichiometric nickel oxide at different sintering temperatures upto 1100 °C. The structure of synthesized compounds were analyzed by X ray diffraction analysis (XRD) and magnetic ordering was studied with the help of Raman scattering spectroscopy for the samples sintered at different temperature. It was found that due to change in sintering temperature the stoichiometry of the sample changes and hence intensity of two magnon band changes. These results were interpreted as the decomposition temperature increases, which heals the defects present in the non-stoichiometric nickel oxide and antiferromagnetic spin correlation changes accordingly.

  7. High-Yield Synthesis of Stoichiometric Boron Nitride Nanostructures

    DOE PAGES

    Nocua, José E.; Piazza, Fabrice; Weiner, Brad R.; ...

    2009-01-01

    Boron nimore » tride (BN) nanostructures are structural analogues of carbon nanostructures but have completely different bonding character and structural defects. They are chemically inert, electrically insulating, and potentially important in mechanical applications that include the strengthening of light structural materials. These applications require the reliable production of bulk amounts of pure BN nanostructures in order to be able to reinforce large quantities of structural materials, hence the need for the development of high-yield synthesis methods of pure BN nanostructures. Using borazine ( B 3 N 3 H 6 ) as chemical precursor and the hot-filament chemical vapor deposition (HFCVD) technique, pure BN nanostructures with cross-sectional sizes ranging between 20 and 50 nm were obtained, including nanoparticles and nanofibers. Their crystalline structure was characterized by (XRD), their morphology and nanostructure was examined by (SEM) and (TEM), while their chemical composition was studied by (EDS), (FTIR), (EELS), and (XPS). Taken altogether, the results indicate that all the material obtained is stoichiometric nanostructured BN with hexagonal and rhombohedral crystalline structure.« less

  8. Electrodeposited non-stoichiometric tungstic acid for electrochromic applications: film growth modes, crystal structure, redox behavior and stability

    NASA Astrophysics Data System (ADS)

    Pugolovkin, Leonid V.; Cherstiouk, Olga V.; Plyasova, Lyudmila M.; Molina, Irina Yu.; Kardash, Tatyana Yu.; Stonkus, Olga A.; Yatsenko, Dmitriy A.; Kaichev, Vasily V.; Tsirlina, Galina A.

    2016-12-01

    Bath composition for cathodic electrodeposition of non-stoichiometric hydrated tungstic acid with high electrochromic efficiency is optimized with account for selective electroreduction of certain isopolytungstates. XRD data for thin electrodeposited films and chemically synthesized bulk tungstic acid dihydrate are compared in the context of reversible oxidation and reduction in hydrogen atmosphere, in presence of Pt catalyst. XPS and TEM techniques are attracted to understand the nature of reversible and less reversible transformations of films in the course of their storage and operation.

  9. Community Characteristics and Leaf Stoichiometric Traits of Desert Ecosystems Regulated by Precipitation and Soil in an Arid Area of China.

    PubMed

    Zhang, Xiaolong; Guan, Tianyu; Zhou, Jihua; Cai, Wentao; Gao, Nannan; Du, Hui; Jiang, Lianhe; Lai, Liming; Zheng, Yuanrun

    2018-01-10

    Precipitation is a key environmental factor determining plant community structure and function. Knowledge of how community characteristics and leaf stoichiometric traits respond to variation in precipitation is crucial for assessing the effects of global changes on terrestrial ecosystems. In this study, we measured community characteristics, leaf stoichiometric traits, and soil properties along a precipitation gradient (35-209 mm) in a desert ecosystem of Northwest China to explore the drivers of these factors. With increasing precipitation, species richness, aboveground biomass, community coverage, foliage projective cover (FPC), and leaf area index (LAI) all significantly increased, while community height decreased. The hyperarid desert plants were characterized by lower leaf carbon (C) and nitrogen/phosphorus (N/P) levels, and stable N and P, and these parameters did not change significantly with precipitation. The growth of desert plants was limited more by N than P. Soil properties, rather than precipitation, were the main drivers of desert plant leaf stoichiometric traits, whereas precipitation made the biggest contribution to vegetation structure and function. These results test the importance of precipitation in regulating plant community structure and composition together with soil properties, and provide further insights into the adaptive strategy of communities at regional scale in response to global climate change.

  10. Community Characteristics and Leaf Stoichiometric Traits of Desert Ecosystems Regulated by Precipitation and Soil in an Arid Area of China

    PubMed Central

    Guan, Tianyu; Zhou, Jihua; Cai, Wentao; Gao, Nannan; Du, Hui; Jiang, Lianhe; Lai, Liming; Zheng, Yuanrun

    2018-01-01

    Precipitation is a key environmental factor determining plant community structure and function. Knowledge of how community characteristics and leaf stoichiometric traits respond to variation in precipitation is crucial for assessing the effects of global changes on terrestrial ecosystems. In this study, we measured community characteristics, leaf stoichiometric traits, and soil properties along a precipitation gradient (35–209 mm) in a desert ecosystem of Northwest China to explore the drivers of these factors. With increasing precipitation, species richness, aboveground biomass, community coverage, foliage projective cover (FPC), and leaf area index (LAI) all significantly increased, while community height decreased. The hyperarid desert plants were characterized by lower leaf carbon (C) and nitrogen/phosphorus (N/P) levels, and stable N and P, and these parameters did not change significantly with precipitation. The growth of desert plants was limited more by N than P. Soil properties, rather than precipitation, were the main drivers of desert plant leaf stoichiometric traits, whereas precipitation made the biggest contribution to vegetation structure and function. These results test the importance of precipitation in regulating plant community structure and composition together with soil properties, and provide further insights into the adaptive strategy of communities at regional scale in response to global climate change. PMID:29320458

  11. Electronic and thermal properties of non-stoichiometric and doped cobaltum antimonide

    NASA Astrophysics Data System (ADS)

    Velasco-Soto, Diego; Menéndez-Proupin, Eduardo; Realyvazquez-Guevara, Rebeca; Andrés Matutes-Aquino, José

    2018-02-01

    The electronic, vibrational and thermal properties of stoichiometric and non-stoichiometric cobalt antimonide CoSb x (x = 2.81, 2.875, and 3) are investigated by means of first principle calculations and thermal measurements. The molar heat capacity, electrical conductivity, and the electronic thermal conductivity are increased by the effect of Sb vacancies. Doping with Te and Ge also increases the electrical and thermal conductivity, suggesting that it can be used to enhance cobaltum antimonide as a thermoelectric material.

  12. Direct observation of vast off-stoichiometric defects in single crystalline SnSe

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Wu, Di; Wu, Lijun; He, Dongsheng

    Single crystalline tin selenide (SnSe) recently emerged as a very promising thermoelectric material for waste heat harvesting and thermoelectric cooling, due to its record high figure of merit ZT in mediate temperature range. The most striking feature of SnSe lies in its extremely low lattice thermal conductivity as ascribed to the anisotropic and highly distorted Sn-Se bonds as well as the giant bond anharmonicity by previous studies, yet no theoretical models so far can give a quantitative explanation to such low a lattice thermal conductivity. Here, we presented direct observation of an astonishingly vast number of off-stoichiometric Sn vacancies andmore » Se interstitials, using sophisticated aberration corrected scanning transmission electron microscope; and credited the previously reported ultralow thermal conductivity of the SnSe single crystalline samples partly to their off-stoichiometric feature. In order to further validate the conclusion, we also synthesized stoichiometric SnSe single crystalline samples, and illustrated that the lattice thermal conductivity is deed much higher as compared with the off-stoichiometric single crystals. Finally, the scattering efficiency of individual point defect on heat-carrying phonons was then discussed in the state-of-art Debye-Callaway model.« less

  13. Direct observation of vast off-stoichiometric defects in single crystalline SnSe

    DOE PAGES

    Wu, Di; Wu, Lijun; He, Dongsheng; ...

    2017-04-06

    Single crystalline tin selenide (SnSe) recently emerged as a very promising thermoelectric material for waste heat harvesting and thermoelectric cooling, due to its record high figure of merit ZT in mediate temperature range. The most striking feature of SnSe lies in its extremely low lattice thermal conductivity as ascribed to the anisotropic and highly distorted Sn-Se bonds as well as the giant bond anharmonicity by previous studies, yet no theoretical models so far can give a quantitative explanation to such low a lattice thermal conductivity. Here, we presented direct observation of an astonishingly vast number of off-stoichiometric Sn vacancies andmore » Se interstitials, using sophisticated aberration corrected scanning transmission electron microscope; and credited the previously reported ultralow thermal conductivity of the SnSe single crystalline samples partly to their off-stoichiometric feature. In order to further validate the conclusion, we also synthesized stoichiometric SnSe single crystalline samples, and illustrated that the lattice thermal conductivity is deed much higher as compared with the off-stoichiometric single crystals. Finally, the scattering efficiency of individual point defect on heat-carrying phonons was then discussed in the state-of-art Debye-Callaway model.« less

  14. Ferromagnetic resonance study of the non-stoichiometric double perovskite Sr2Fe1+xMo1-xO6

    NASA Astrophysics Data System (ADS)

    Medina, J. De La Torre; Piraux, L.; Soto, T. E.; Morales, R.; Navarro, O.

    2018-02-01

    In this work we report a ferromagnetic resonance study on the magnetic properties of double perovskite compounds fab-ricated by solid state reaction. Based on a mean field approach, along with morphological considerations, we accurately determined the saturation magnetization of the non-stoichiometric double perovskite Sr2Fe1+xMo1-xO6. Our approach has revealed a direct in-fluence of composition on the overall magnetic behavior of these materials, providing complementary experimental evidence that corroborates previous theoretical findings. The understanding of the influence of composition is of paramount importance for the design of ferromagnetic oxides with tunable magnetic and magneto-transport behavior.

  15. 40 CFR 1065.362 - Non-stoichiometric raw exhaust FID O2 interference verification.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 33 2011-07-01 2011-07-01 false Non-stoichiometric raw exhaust FID O2... Measurements § 1065.362 Non-stoichiometric raw exhaust FID O2 interference verification. (a) Scope and frequency. If you use FID analyzers for raw exhaust measurements from engines that operate in a non...

  16. 40 CFR 1065.362 - Non-stoichiometric raw exhaust FID O2 interference verification.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Non-stoichiometric raw exhaust FID O2... Measurements § 1065.362 Non-stoichiometric raw exhaust FID O2 interference verification. (a) Scope and frequency. If you use FID analyzers for raw exhaust measurements from engines that operate in a non...

  17. Effect of non-stoichiometric solution chemistry on improving the performance of wide-bandgap perovskite solar cells

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Yang, Mengjin; Kim, Dong Hoe; Yu, Yue

    A high-efficiency wide-bandgap (WBG) perovskite solar cell is critical for developing perovskite-related (e.g., all-perovskite, perovskite/Si, or perovskite/Cu(In,Ga)Se 2) tandem devices. Here, we demonstrate the use of non-stoichiometric precursor chemistry with excess methylammonium halides (MAX; X = I, Br, or Cl) for preparing high-quality ~1.75-eV FA 0.83Cs 0.17Pb(I 0.6Br 0.4) 3 perovskite solar cells. Among various methylammonium halides, using excess MABr in the non-stoichiometric precursor exhibits the strongest effect on improving perovskite crystallographic properties and device characteristics without affecting the perovskite composition. In contrast, using excess MAI significantly reduces the bandgap of perovskite due to the replacement of Br with I.more » Using 40% excess MABr, we demonstrate a single-junction WBG perovskite solar cell with stabilized efficiency of 16.4%. We further demonstrate a 20.3%-efficient 4-terminal tandem device by using a 14.7%-efficient semi-transparent WBG perovskite top cell and an 18.6%-efficient unfiltered (5.6%-efficient filtered) Si bottom cell.« less

  18. Effect of non-stoichiometric solution chemistry on improving the performance of wide-bandgap perovskite solar cells

    DOE PAGES

    Yang, Mengjin; Kim, Dong Hoe; Yu, Yue; ...

    2017-10-02

    A high-efficiency wide-bandgap (WBG) perovskite solar cell is critical for developing perovskite-related (e.g., all-perovskite, perovskite/Si, or perovskite/Cu(In,Ga)Se 2) tandem devices. Here, we demonstrate the use of non-stoichiometric precursor chemistry with excess methylammonium halides (MAX; X = I, Br, or Cl) for preparing high-quality ~1.75-eV FA 0.83Cs 0.17Pb(I 0.6Br 0.4) 3 perovskite solar cells. Among various methylammonium halides, using excess MABr in the non-stoichiometric precursor exhibits the strongest effect on improving perovskite crystallographic properties and device characteristics without affecting the perovskite composition. In contrast, using excess MAI significantly reduces the bandgap of perovskite due to the replacement of Br with I.more » Using 40% excess MABr, we demonstrate a single-junction WBG perovskite solar cell with stabilized efficiency of 16.4%. We further demonstrate a 20.3%-efficient 4-terminal tandem device by using a 14.7%-efficient semi-transparent WBG perovskite top cell and an 18.6%-efficient unfiltered (5.6%-efficient filtered) Si bottom cell.« less

  19. Martensitic transformation in as-grown and annealed near-stoichiometric epitaxial Ni2MnGa thin films

    NASA Astrophysics Data System (ADS)

    Machain, P.; Condó, A. M.; Domenichini, P.; Pozo López, G.; Sirena, M.; Correa, V. F.; Haberkorn, N.

    2015-08-01

    Magnetic shape memory nanostructures have a great potential in the field of the nanoactuators. The relationship between dimensionality, microstructure and magnetism characterizes the materials performance. Here, we study the martensitic transformation in supported and free-standing epitaxial Ni47Mn24Ga29 films grown by sputtering on (0 0 1) MgO using a stoichiometric Ni2MnGa target. The films have a Curie temperature of ~390 K and a martensitic transition temperature of ~120 K. Similar transition temperatures have been observed in films with thicknesses of 1, 3 and 4 μm. Thicker films (with longer deposition time) present a wider martensitic transformation range that can be associated with small gradients in their chemical concentration due to the high vapour pressure of Mn and Ga. The magnetic anisotropy of the films shows a strong change below the martensitic transformation temperature. No features associated with variant reorientation induced by magnetic field have been observed. Annealed films in the presence of a Ni2MnGa bulk reference change their chemical composition to Ni49Mn26Ga25. The change in the chemical composition increases the martensitic transformation temperature, being closer to the stoichiometric compound, and reduces the transformation hysteresis. In addition, sharper transformations are obtained, which indicate that chemical inhomogeneities and defects are removed. Our results indicate that the properties of Ni-Mn-Ga thin films grown by sputtering can be optimized (fixing the chemical concentration and removing crystalline defects) by the annealing process, which is promising for the development of micromagnetic shape memory devices.

  20. Stoichiometric network theory for nonequilibrium biochemical systems.

    PubMed

    Qian, Hong; Beard, Daniel A; Liang, Shou-dan

    2003-02-01

    We introduce the basic concepts and develop a theory for nonequilibrium steady-state biochemical systems applicable to analyzing large-scale complex isothermal reaction networks. In terms of the stoichiometric matrix, we demonstrate both Kirchhoff's flux law sigma(l)J(l)=0 over a biochemical species, and potential law sigma(l) mu(l)=0 over a reaction loop. They reflect mass and energy conservation, respectively. For each reaction, its steady-state flux J can be decomposed into forward and backward one-way fluxes J = J+ - J-, with chemical potential difference deltamu = RT ln(J-/J+). The product -Jdeltamu gives the isothermal heat dissipation rate, which is necessarily non-negative according to the second law of thermodynamics. The stoichiometric network theory (SNT) embodies all of the relevant fundamental physics. Knowing J and deltamu of a biochemical reaction, a conductance can be computed which directly reflects the level of gene expression for the particular enzyme. For sufficiently small flux a linear relationship between J and deltamu can be established as the linear flux-force relation in irreversible thermodynamics, analogous to Ohm's law in electrical circuits.

  1. Consequences of the superstrong nature of chalcogenide glass-forming liquids at select compositions

    NASA Astrophysics Data System (ADS)

    Gunasekera, Kapila; Bhosle, Siddhesh; Boolchand, Punit; Micoulaut, Matthieu

    2014-03-01

    Growth of homogeneous melts of stoichiometric compositions of chalcogenides is facilitated by underlying crystalline phases. Such is not the case for non-stoichiometric melt compositions in which, for example, variation of fragility (m) from complex specific heat measurements show global minimum at an extremely low value (m =14.8(0.5)) in the 21.5% stoichiometric melts/glasses due to their heterogeneity. By directly mapping melt stoichiometry variation along a quartz tube as a function of reaction time of starting materials at a fixed temperature T>Tg over days, we have observed a slowdown of melt-homogenization by the super-strong melt compositions, 21.5%

  2. Ultraviolet photorefractive effect in Mg-doped near-stoichiometric LiNbO 3

    NASA Astrophysics Data System (ADS)

    Zhu, Dengsong; Xu, Jingjun; Qiao, Haijun; Shi, Yanli; Gao, Feng; Li, Wei; Fu, Bo; Zhang, Guaquan; Zheng, Ke

    2006-10-01

    The ultraviolet photorefractive effect of Mg-doped near-stoichiometric LiNbO3 crystals prepared by vapor transport equilibration (VTE) technique was studied at 351 nm. It was found in the near-stoichiometric LiNbO3 crystals that the ultraviolet photorefractive effect could be enhanced greatly with the increase of Mg concentration. Based on the activation energy of dark decay of the photorefractive grating, possible centers responsible for the ultraviolet photorefractive effect were also discussed.

  3. Studies on the O-polysaccharide of Escherichia albertii O2 characterized by non-stoichiometric O-acetylation and non-stoichiometric side-chain l-fucosylation.

    PubMed

    Naumenko, Olesya I; Zheng, Han; Xiong, Yanwen; Senchenkova, Sof'ya N; Wang, Hong; Shashkov, Alexander S; Li, Qun; Wang, Jianping; Knirel, Yuriy A

    2018-05-22

    An O-polysaccharide was isolated from the lipopolysaccharide of Escherichia albertii O2 and studied by chemical methods and 1D and 2D 1 H and 13 C NMR spectroscopy. The following structure of the O-polysaccharide was established: . The O-polysaccharide is characterized by masked regularity owing to a non-stoichiometric O-acetylation of an l-fucose residue in the main chain and a non-stoichiometric side-chain l-fucosylation of a β-GlcNAc residue. A regular linear polysaccharide was obtained by sequential Smith degradation and alkaline O-deacetylation of the O-polysaccharide. The content of the O-antigen gene cluster of E. albertii O2 was found to be essentially consistent with the O-polysaccharide structure established. Copyright © 2018 Elsevier Ltd. All rights reserved.

  4. Fragility and super-strong character of non-stoichiometric chalcogenides: implications on melt homogenization

    NASA Astrophysics Data System (ADS)

    Ravindren, Sriram; Gunasekera, Kapila; Boolchand, Punit; Micoulaut, Matthieu

    2014-03-01

    The kinetics of homogenization of binary AsxSe100-x melts in the As concentration range 0% composition and the fragility index m displays a broad global minimum in 20% compositions in 20% stoichiometric As-Se compositions is reported. Fragilities of the Ge-As-Se are reported and a correlation observed with fragilities of As-Se and Ge-Se. Supported by NSF grant DMR 08-53957.

  5. Stability and activity of lysozyme in stoichiometric and non-stoichiometric protic ionic liquid (PIL)-water systems

    NASA Astrophysics Data System (ADS)

    Wijaya, Emmy C.; Separovic, Frances; Drummond, Calum J.; Greaves, Tamar L.

    2018-05-01

    There has been a substantial increase in enzyme applications within the biochemical and pharmaceutical industries, for example, as industrial biocatalysts. However, enzymes have narrow marginal stability which makes them prone to become inactive and/or denature with a slight change in the solvent environment. Typically industrial applications require harsher solvent environments than enzyme native environments, and hence there is a need to understand solvent-protein interactions in order to develop strategies to maintain, or enhance, the enzymatic activity under industrially relevant solvent conditions. Previously we have shown that protic ionic liquids (PILs) with water can have a stabilising effect on lysozyme, with a large variation dependent on which PIL ions are present, and the water concentration [E. C. Wijaya et al., Phys. Chem. Chem. Phys. 18(37), 25926-25936 (2016)]. Here we extend on this work using non-stoichiometric aqueous PIL solvents to investigate, and isolate, the role of pH and ionicity on enzymes. We have used the PILs ethylammonium nitrate (EAN) and ethanolammonium formate (EOAF) since our previous work has identified these as good solvents for lysozyme. Solvent libraries were made from these two PILs with an additional precursor acid or base to modify the acidity/basicity of the neutral stoichiometric PIL, and with water added, to have solutions with 4-17 mol. % of the PIL ions in water. Molar ratios of base:acid were varied between 1:1.05 and 2:1 for EAN and 1:1.25 and 2:1 for EOAF, which enabled from highly basic to highly acidic solutions to be obtained. This was to modify the acidity/basicity of the neutral stoichiometric PILs, without the addition of buffers. The structure and stability of hen egg white lysozyme (HEWL) were explored under these solvent conditions using synchrotron small angle X-ray scattering (SAXS), Fourier transform infrared (FTIR), and activity assays. The radius of gyration and Kratky plots obtained from the SAXS data

  6. Comparison of the Tensile, Creep, and Rupture Strength Properties of Stoichiometric SiC Fibers

    NASA Technical Reports Server (NTRS)

    Yun, H. M.; DiCarlo, J. A.

    1999-01-01

    Tensile strength, creep strength, and rupture strength properties were measured for the following types of polymer-derived stoichiometric SiC fibers: Hi-Nicalon Type S from Nippon Carbon, Tyranno SA from Ube, and Sylramic from Dow Corning. Also included in this study were an earlier version of the SA fiber plus two recent developmental versions of the Sylramic fiber. The tensile strength measurements were made at room temperature on as-received fibers and on fibers after high-temperature inert exposure. The creep-rupture property data were obtained at 1400 deg C in air as well as, argon. Some fiber types showed strong effects of environment on their strength properties. These results are compared and discussed in terms of underlying mechanisms and implications for ceramic composites.

  7. Conductive ceramic composition and method of preparation

    DOEpatents

    Smith, J.L.; Kucera, E.H.

    1991-04-16

    A ceramic anode composition is formed of a multivalent metal oxide or oxygenate such as an alkali metal, transition metal oxygenate. The anode is prepared as a non-stoichiometric crystalline structure by reaction and conditioning in a hydrogen gas cover containing minor proportions of carbon dioxide and water vapor. The structure exhibits a single phase and substantially enhanced electrical conductivity over that of the corresponding stoichiometric structure. Unexpectedly, such oxides and oxygenates are found to be stable in the reducing anode fuel gas of a molten carbonate fuel cell. 4 figures.

  8. Conductive ceramic composition and method of preparation

    DOEpatents

    Smith, James L.; Kucera, Eugenia H.

    1991-01-01

    A ceramic anode composition is formed of a multivalent metal oxide or oxygenate such as an alkali metal, transition metal oxygenate. The anode is prepared as a non-stoichiometric crystalline structure by reaction and conditioning in a hydrogen gas cover containing minor proportions of carbon dioxide and water vapor. The structure exhibits a single phase and substantially enhanced electrical conductivity over that of the corresponding stoichiometric structure. Unexpectedly, such oxides and oxygenates are found to be stable in the reducing anode fuel gas of a molten carbonate fuel cell.

  9. Constraint-based stoichiometric modelling from single organisms to microbial communities

    PubMed Central

    Olivier, Brett G.; Bruggeman, Frank J.; Teusink, Bas

    2016-01-01

    Microbial communities are ubiquitously found in Nature and have direct implications for the environment, human health and biotechnology. The species composition and overall function of microbial communities are largely shaped by metabolic interactions such as competition for resources and cross-feeding. Although considerable scientific progress has been made towards mapping and modelling species-level metabolism, elucidating the metabolic exchanges between microorganisms and steering the community dynamics remain an enormous scientific challenge. In view of the complexity, computational models of microbial communities are essential to obtain systems-level understanding of ecosystem functioning. This review discusses the applications and limitations of constraint-based stoichiometric modelling tools, and in particular flux balance analysis (FBA). We explain this approach from first principles and identify the challenges one faces when extending it to communities, and discuss the approaches used in the field in view of these challenges. We distinguish between steady-state and dynamic FBA approaches extended to communities. We conclude that much progress has been made, but many of the challenges are still open. PMID:28334697

  10. Enzymatic production of 'monoclonal stoichiometric' single-stranded DNA oligonucleotides.

    PubMed

    Ducani, Cosimo; Kaul, Corinna; Moche, Martin; Shih, William M; Högberg, Björn

    2013-07-01

    Single-stranded oligonucleotides are important as research tools, as diagnostic probes, in gene therapy and in DNA nanotechnology. Oligonucleotides are typically produced via solid-phase synthesis, using polymer chemistries that are limited relative to what biological systems produce. The number of errors in synthetic DNA increases with oligonucleotide length, and the resulting diversity of sequences can be a problem. Here we present the 'monoclonal stoichiometric' (MOSIC) method for enzyme-mediated production of DNA oligonucleotides. We amplified oligonucleotides from clonal templates derived from single bacterial colonies and then digested cutter hairpins in the products, which released pools of oligonucleotides with precisely controlled relative stoichiometric ratios. We prepared 14-378-nucleotide MOSIC oligonucleotides either by in vitro rolling-circle amplification or by amplification of phagemid DNA in Escherichia coli. Analyses of the formation of a DNA crystal and folding of DNA nanostructures confirmed the scalability, purity and stoichiometry of the produced oligonucleotides.

  11. Stoichiometric Experiments with Alkane Combustion: A Classroom Demonstration

    ERIC Educational Resources Information Center

    Zhilin, Denis M.

    2012-01-01

    A simple, effective demonstration of the concept of limiting and excess reagent is presented. Mixtures of either air/methane (from a gas line) or air/butane (from a disposable cigarette lighter) contained in a plastic 2 L soda bottles are ignited. The mixtures combust readily when air/fuel ratios are stoichiometric, but not at a 2-fold excess of…

  12. Optical excitation of carbon nanotubes drives stoichiometric reaction with diazonium salts

    NASA Astrophysics Data System (ADS)

    Powell, Lyndsey; Piao, Yanmei; Wang, Yuhuang; YuHuang Wang Research Group Team

    Covalent chemistry is known to lack the precision required to tailor the physical properties of carbon nanostructures. Here we show that, for the first time, light can be used to drive a typically inefficient reaction with single-walled carbon nanotubes in a more stoichiometric fashion. Specifically, our experimental results suggest that light can enhance the reaction rate of diazonium salt with carbon nanotubes by as much as 35-fold, making possible stoichiometric control of the covalent bonding of a functional group to the sp2 carbon lattice. This light-controlled reaction paves the way for the possibility of highly selective and precise chemistry on single-walled carbon nanotubes and other graphitic nanostructures.

  13. Enzymatic Production of Monoclonal Stoichiometric Single-Stranded DNA Oligonucleotides

    PubMed Central

    Ducani, Cosimo; Kaul, Corinna; Moche, Martin; Shih, William M.; Högberg, Björn

    2013-01-01

    Single-stranded oligonucleotides are important as research tools as probes for diagnostics and gene therapy. Today, production of oligonucleotides is done via solid-phase synthesis. However, the capabilities of current polymer chemistry are limited in comparison to what can be produced in biological systems. The errors in synthetic DNA increases with oligonucleotide length, and sequence diversity can often be a problem. Here, we present the Monoclonal Stoichiometric (MOSIC) method for enzymatic DNA oligonucleotide production. Using this method, we amplify oligonucleotides from clonal templates followed by digestion of a cutter-hairpin, resulting in pools of monoclonal oligonucleotides with precisely controlled relative stoichiometric ratios. We present data where MOSIC oligonucleotides, 14–378 nt long, were prepared either by in vitro rolling-circle amplification, or by amplification in Escherichia coli in the form of phagemid DNA. The formation of a DNA crystal and folding of DNA nanostructures confirmed the scalability, purity and stoichiometry of the produced oligonucleotides. PMID:23727986

  14. Physiological tolerance and stoichiometric potential of cyanobacteria for hydrocarbon fuel production.

    PubMed

    Kämäräinen, Jari; Knoop, Henning; Stanford, Natalie J; Guerrero, Fernando; Akhtar, M Kalim; Aro, Eva-Mari; Steuer, Ralf; Jones, Patrik R

    2012-11-30

    Cyanobacteria are capable of directly converting sunlight, carbon dioxide and water into hydrocarbon fuel or precursors thereof. Many biological and non-biological factors will influence the ability of such a production system to become economically sustainable. We evaluated two factors in engineerable cyanobacteria which could potentially limit economic sustainability: (i) tolerance of the host to the intended end-product, and (ii) stoichiometric potential for production. Alcohols, when externally added, inhibited growth the most, followed by aldehydes and acids, whilst alkanes were the least inhibitory. The growth inhibition became progressively greater with increasing chain-length for alcohols, whilst the intermediate C6 alkane caused more inhibition than both C3 and C11 alkane. Synechocystis sp. PCC 6803 was more tolerant to some of the tested chemicals than Synechococcus elongatus PCC 7942, particularly ethanol and undecane. Stoichiometric evaluation of the potential yields suggested that there is no difference in the potential productivity of harvestable energy between any of the studied fuels, with the exception of ethylene, for which maximal stoichiometric yield is considerably lower. In summary, it was concluded that alkanes would constitute the best choice metabolic end-product for fuel production using cyanobacteria if high-yielding strains can be developed. Copyright © 2012 Elsevier B.V. All rights reserved.

  15. Intrinsic high electrical conductivity of stoichiometric SrNb O3 epitaxial thin films

    NASA Astrophysics Data System (ADS)

    Oka, Daichi; Hirose, Yasushi; Nakao, Shoichiro; Fukumura, Tomoteru; Hasegawa, Tetsuya

    2015-11-01

    SrV O3 and SrNb O3 are perovskite-type transition-metal oxides with the same d1 electronic configuration. Although SrNb O3 (4 d1 ) has a larger d orbital than SrV O3 (3 d1 ), the reported electrical resistivity of SrNb O3 is much higher than that of SrV O3 , probably owing to nonstoichiometry. In this paper, we grew epitaxial, high-conductivity stoichiometric SrNb O3 using pulsed laser deposition. The growth temperature strongly affected the Sr/Nb ratio and the oxygen content of the films, and we obtained stoichiometric SrNb O3 at a very narrow temperature window around 630 °C. The stoichiometric SrNb O3 epitaxial thin films grew coherently on KTa O3 (001) substrates with high crystallinity. The room-temperature resistivity of the stoichiometric film was 2.82 ×10-5Ω cm , one order of magnitude lower than the lowest reported value of SrNb O3 and comparable with that of SrV O3 . We observed a T -square dependence of resistivity below T*=180 K and non-Drude behavior in near-infrared absorption spectroscopy, attributable to the Fermi-liquid nature caused by electron correlation. Analysis of the T -square coefficient A of resistivity experimentally revealed that the 4 d orbital of Nb that is larger than the 3 d ones certainly contributes to the high electrical conduction of SrNb O3 .

  16. Foraging behavior by Daphnia in stoichiometric gradients of food quality.

    PubMed

    Schatz, Greg S; McCauley, Edward

    2007-10-01

    Mismatches in the elemental composition of herbivores and their resources can impact herbivore growth and reproduction. In aquatic systems, the ratio of elements, such as C, P, and N, is used to characterize the food quality of algal prey. For example, large increases in the C:P ratio of edible algae can decrease rates of growth and reproduction in Daphnia. Current theory emphasizes that Daphnia utilize only assimilation and respiration processes to maintain an optimal elemental composition, yet studies of terrestrial herbivores implicate behavioral processes in coping with local variation in food quality. We tested the ability of juvenile and adult Daphnia to locate regions of high-quality food within a spatial gradient of algal prey differing in C:P ratio, while holding food density constant over space. Both juveniles and adults demonstrated similar behavior by quickly locating (i.e., <10 min) the region of high food quality. Foraging paths were centred on regions of high food quality and these differed significantly from paths of individuals exposed to a homogeneous environment of both food density and food quality. Ingestion rate experiments on algal prey of differing stoichiometric ratio show that individuals can adjust their intake rate over fast behavioral time-scales, and we use these data to examine how individuals choose foraging locations when presented with a spatial gradient that trades off food quality and food quantity. Daphnia reared under low food quality conditions chose to forage in regions of high food quality even though they could attain the same C ingestion rate elsewhere along a spatial gradient. We argue that these aspects of foraging behavior by Daphnia have important implications for how these herbivores manage their elemental composition and our understanding of the dynamics of these herbivore-plant systems in lakes and ponds where spatial variation in food quality is present.

  17. On the stability of sub-stoichiometric uranium oxides

    NASA Astrophysics Data System (ADS)

    Winer, K.; Colmenares, C. A.; Smith, R. L.; Wooten, F.

    1986-12-01

    The oxidation of clean, high-purity polycrystalline uranium metal surfaces for low exposures to dry oxygen was studied with AES and XPS in an attempt to substantiate claims for the formation of a stable UO surface phase at ambient temperatures. We found no evidence for such a surface phase and found instead that grossly sub-stoichiometric surface oxides were formed after sequential oxygen saturation and heating.

  18. The Effect of Time, Temperature and Composition on Boron Carbide Synthesis by Sol-gel Method

    NASA Astrophysics Data System (ADS)

    Hadian, A. M.; Bigdeloo, J. A.

    2008-02-01

    To minimize free carbon residue in the boron carbide (B4C) powder, a modified sol-gel process is performed where the starting materials as boric acid and citric acid compositions are adjusted. Because of boron loss in the form of B2O2(g) during the reduction reaction of the stoichiometric starting composition, the final B4C powders contain carbon residues. Thus, an excess H3BO3 is used in the reaction to compensate the loss and to obtain stoichiometric powders. Parameters of production have been determined using x-ray diffraction analysis and particle size analyses. The synthesized B4C powder using an excess boric acid composition shows no trace of carbon.

  19. Determination of performance of non-ideal aluminized explosives.

    PubMed

    Keshavarz, Mohammad Hossein; Mofrad, Reza Teimuri; Poor, Karim Esmail; Shokrollahi, Arash; Zali, Abbas; Yousefi, Mohammad Hassan

    2006-09-01

    Non-ideal explosives can have Chapman-Jouguet (C-J) detonation pressure significantly different from those expected from existing thermodynamic computer codes, which usually allows finding the parameters of ideal detonation of individual high explosives with good accuracy. A simple method is introduced by which detonation pressure of non-ideal aluminized explosives with general formula C(a)H(b)N(c)O(d)Al(e) can be predicted only from a, b, c, d and e at any loading density without using any assumed detonation products and experimental data. Calculated detonation pressures show good agreement with experimental values with respect to computed results obtained by complicated computer code. It is shown here how loading density and atomic composition can be integrated into an empirical formula for predicting detonation pressure of proposed aluminized explosives.

  20. Exhaustive identification of steady state cycles in large stoichiometric networks

    PubMed Central

    Wright, Jeremiah; Wagner, Andreas

    2008-01-01

    Background Identifying cyclic pathways in chemical reaction networks is important, because such cycles may indicate in silico violation of energy conservation, or the existence of feedback in vivo. Unfortunately, our ability to identify cycles in stoichiometric networks, such as signal transduction and genome-scale metabolic networks, has been hampered by the computational complexity of the methods currently used. Results We describe a new algorithm for the identification of cycles in stoichiometric networks, and we compare its performance to two others by exhaustively identifying the cycles contained in the genome-scale metabolic networks of H. pylori, M. barkeri, E. coli, and S. cerevisiae. Our algorithm can substantially decrease both the execution time and maximum memory usage in comparison to the two previous algorithms. Conclusion The algorithm we describe improves our ability to study large, real-world, biochemical reaction networks, although additional methodological improvements are desirable. PMID:18616835

  1. Size Dependence of Metal-Insulator Transition in Stoichiometric Fe₃O4₄Nanocrystals.

    PubMed

    Lee, Jisoo; Kwon, Soon Gu; Park, Je-Geun; Hyeon, Taeghwan

    2015-07-08

    Magnetite (Fe3O4) is one of the most actively studied materials with a famous metal-insulator transition (MIT), so-called the Verwey transition at around 123 K. Despite the recent progress in synthesis and characterization of Fe3O4 nanocrystals (NCs), it is still an open question how the Verwey transition changes on a nanometer scale. We herein report the systematic studies on size dependence of the Verwey transition of stoichiometric Fe3O4 NCs. We have successfully synthesized stoichiometric and uniform-sized Fe3O4 NCs with sizes ranging from 5 to 100 nm. These stoichiometric Fe3O4 NCs show the Verwey transition when they are characterized by conductance, magnetization, cryo-XRD, and heat capacity measurements. The Verwey transition is weakly size-dependent and becomes suppressed in NCs smaller than 20 nm before disappearing completely for less than 6 nm, which is a clear, yet highly interesting indication of a size effect of this well-known phenomena. Our current work will shed new light on this ages-old problem of Verwey transition.

  2. Kinetic modeling of non-ideal explosives with CHEETAH

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Fried, L E; Howard, W M; Souers, P C

    1998-08-06

    We report an implementation of the Wood-Kirkwood kinetic detonation model based on multi-species equations of state and multiple reaction rate laws. Finite rate laws are used for the slowest chemical reactions. Other reactions are given infinite rates and are kept in constant thermodynamic equilibrium. We model a wide range of ideal and non-ideal composite energetic materials. We find that we can replicate experimental detonation velocities to within a few per cent, while obtaining good agreement with estimated reaction zone lengths. The detonation velocity as a function of charge radius is also correctly reproduced.

  3. Oxygen transport in off-stoichiometric uranium dioxide mediated by defect clustering dynamics

    DOE PAGES

    Yu, Jianguo; Bai, Xian -Ming; El-Azab, Anter; ...

    2015-03-05

    In this study, oxygen transport is central to many properties of oxides such as stoichiometric changes, phase transformation and ionic conductivity. In this paper, we report a mechanism for oxygen transport in uranium dioxide (UO 2) in which the kinetics is mediated by defect clustering dynamics. In particular, the kinetic Monte Carlo (KMC) method has been used to investigate the kinetics of oxygen transport in UO 2 under the condition of creation and annihilation of oxygen vacancies and interstitials as well as oxygen interstitial clustering, with variable offstoichiometry and temperature conditions. It is found that in hypo-stoichiometric UO 2-x, oxygenmore » transport is well described by the vacancy diffusion mechanism while in hyper-stoichiometric UO 2+x, oxygen interstitial cluster diffusion contributes significantly to oxygen transport kinetics, particularly at high temperatures and high off-stoichiometry levels. It is also found that diinterstitial clusters and single interstitials play dominant roles in oxygen diffusion while other larger clusters have negligible contributions. However, the formation, coalescence and dissociation of these larger clusters indirectly affects the overall oxygen diffusion due to their interactions with mono and di-interstitials, thus providing a explanation of the experimental observation of saturation or even drop of oxygen diffusivity at high off-stoichiometry.« less

  4. Elemental stoichiometry and compositions of weevil larvae and two acorn hosts under natural phosphorus variation

    NASA Astrophysics Data System (ADS)

    Ji, Huawei; Du, Baoming; Liu, Chunjiang

    2017-04-01

    To understand how different trophic organisms in a parasite food chain adapt to the differences in soil nutrient conditions, we investigated stoichiometric variation and homeostasis of multiple elements in two acorn trees, Quercus variabilis and Quercus acutissima, and their parasite weevil larvae (Curculio davidi Fairmaire) at phosphorus (P)-deficient and P-rich sites in subtropical China where P-rich ores are scattered among dominant P-deficient soils. Results showed that elemental stoichiometry and compositions of both acorns and weevil larvae differed significantly between P-deficient and P-rich sites (p < 0.05), with the largest contribution of acorn and weevil larva P in distinguishing the stoichiometric compositions between the two site types. The two acorn species were statistically separated by their acorn elemental stoichiometry and compositions (p < 0.05), but no difference was observed on weevil larvae between the two acorn species. P was one of the few elements that were non strict homeostasis in both acorns and weevil larvae. These findings highlight the importance of both environmental influence in elemental stoichiometry and composition and physiological regulations of nutritional needs in organisms and provide possible stoichiometric responses of both plants and animals to P loading, a worldwide issue from excess release of P into the environment.

  5. Stoichiometric network constraints on xylose metabolism by recombinant Saccharomyces cerevisiae

    Treesearch

    Yong-Su Jin; Thomas W. Jeffries

    2004-01-01

    Metabolic pathway engineering is constrained by the thermodynamic and stoichiometric feasibility of enzymatic activities of introduced genes. Engineering of xylose metabolism in Saccharomyces cerevisiae has focused on introducing genes for the initial xylose assimilation steps from Pichia stipitis, a xylose-fermenting yeast, into S. cerevisiae, a yeast raditionally...

  6. Light-induced absorption and its relaxation under illumination of continuous wave ultraviolet light in Mn-doped near-stoichiometric LiNbO{sub 3}

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Liu Youwen; Kitamura, Kenji; Takekawa, Shunji

    2005-04-01

    The steady-state light-induced absorption and the temporal relaxation behavior under illumination of cw ultraviolet light in Mn-doped near-stoichiometric LiNbO{sub 3} with different crystal compositions are investigated. The ultraviolet-light-induced absorption has been assigned to small polarons Nb{sub Li}{sup 4+} by measuring the absorption spectra at room temperature. The dependences of relaxation behaviors (time constant and stretching factor) of light-induced absorption on various illumination conditions (intensity, polarization) and temperature are presented, which are very different from those observed in Fe-doped LiNbO{sub 3} illuminated with highly intense light pulse, though the temporal relaxation follows the same stretched-exponential decay behavior in both cases. Themore » results are explained reasonably by using the model of distance-dependent electron transition probabilities between localized deep traps and small polarons without any additional assumptions, and discussed to tailor doped near-stoichiometric LiNbO{sub 3} crystals for two-color holographic recording with cw laser light.« less

  7. Not All Ideals are Equal: Intrinsic and Extrinsic Ideals in Relationships.

    PubMed

    Rodriguez, Lindsey M; Hadden, Benjamin W; Knee, C Raymond

    2015-03-01

    The ideal standards model suggests that greater consistency between ideal standards and actual perceptions of one's relationship predicts positive relationship evaluations; however, no research has evaluated whether this differs across types of ideals. A self-determination theory perspective was derived to test whether satisfaction of intrinsic ideals buffers the importance of extrinsic ideals. Participants (N=195) in committed relationships directly and indirectly reported the extent to which their partner met their ideal on two dimensions: intrinsic (e.g., warm, intimate) and extrinsic (e.g., attractive, successful). Relationship need fulfillment and relationship quality were also assessed. Hypotheses were largely supported, such that satisfaction of intrinsic ideals more strongly predicted relationship functioning, and satisfaction of intrinsic ideals buffered the relevance of extrinsic ideals for outcomes.

  8. Not All Ideals are Equal: Intrinsic and Extrinsic Ideals in Relationships

    PubMed Central

    Rodriguez, Lindsey M.; Hadden, Benjamin W.; Knee, C. Raymond

    2015-01-01

    The ideal standards model suggests that greater consistency between ideal standards and actual perceptions of one’s relationship predicts positive relationship evaluations; however, no research has evaluated whether this differs across types of ideals. A self-determination theory perspective was derived to test whether satisfaction of intrinsic ideals buffers the importance of extrinsic ideals. Participants (N=195) in committed relationships directly and indirectly reported the extent to which their partner met their ideal on two dimensions: intrinsic (e.g., warm, intimate) and extrinsic (e.g., attractive, successful). Relationship need fulfillment and relationship quality were also assessed. Hypotheses were largely supported, such that satisfaction of intrinsic ideals more strongly predicted relationship functioning, and satisfaction of intrinsic ideals buffered the relevance of extrinsic ideals for outcomes. PMID:25821396

  9. Advanced Stoichiometric Analysis of Metabolic Networks of Mammalian Systems

    PubMed Central

    Orman, Mehmet A.; Berthiaume, Francois; Androulakis, Ioannis P.; Ierapetritou, Marianthi G.

    2013-01-01

    Metabolic engineering tools have been widely applied to living organisms to gain a comprehensive understanding about cellular networks and to improve cellular properties. Metabolic flux analysis (MFA), flux balance analysis (FBA), and metabolic pathway analysis (MPA) are among the most popular tools in stoichiometric network analysis. Although application of these tools into well-known microbial systems is extensive in the literature, various barriers prevent them from being utilized in mammalian cells. Limited experimental data, complex regulatory mechanisms, and the requirement of more complex nutrient media are some major obstacles in mammalian cell systems. However, mammalian cells have been used to produce therapeutic proteins, to characterize disease states or related abnormal metabolic conditions, and to analyze the toxicological effects of some medicinally important drugs. Therefore, there is a growing need for extending metabolic engineering principles to mammalian cells in order to understand their underlying metabolic functions. In this review article, advanced metabolic engineering tools developed for stoichiometric analysis including MFA, FBA, and MPA are described. Applications of these tools in mammalian cells are discussed in detail, and the challenges and opportunities are highlighted. PMID:22196224

  10. Identification of New Cocrystal Systems with Stoichiometric Diversity of Salicylic Acid Using Thermal Methods.

    PubMed

    Zhou, Zhengzheng; Chan, Hok Man; Sung, Herman H-Y; Tong, Henry H Y; Zheng, Ying

    2016-04-01

    The purpose of this work was to develop thermal methods to identify cocrystal systems with stoichiometric diversity. Differential scanning calorimetry (DSC) and hot stage microscopy (HSM) have been applied to study the stoichiometric diversity phenomenon on cocrystal systems of the model compound salicylic acid (SA) with different coformers (CCFs). The DSC method was particularly useful in the identification of cocrystal re-crystallization, especially to improve the temperature resolution using a slower heating rate. HSM was implemented as a complementary protocol to confirm the DSC results. The crystal structures were elucidated by single-crystal X-ray diffraction (SXRD). Two new cocrystal systems consisting of salicylic acid-benzamide (SA-BZD, 1:1, 1:2) and salicylic acid-isonicotinamide (SA-ISN, 1:1, 2:1) have been identified in the present work. The chemical structures of the newly discovered cocrystals SA-BZD (1:2) and SA-ISN (2:1) have been elucidated using X-ray single crystal and powder diffraction methods. The developed thermal methods could rapidly identify cocrystal systems with stoichiometric diversity, with the potential to discover new pharmaceutical cocrystals in the future.

  11. A genomic perspective on stoichiometric regulation of soil carbon cycling.

    PubMed

    Hartman, Wyatt H; Ye, Rongzhong; Horwath, William R; Tringe, Susannah G

    2017-12-01

    Similar to plant growth, soil carbon (C) cycling is constrained by the availability of nitrogen (N) and phosphorus (P). We hypothesized that stoichiometric control over soil microbial C cycling may be shaped by functional guilds with distinct nutrient substrate preferences. Across a series of rice fields spanning 5-25% soil C (N:P from 1:12 to 1:70), C turnover was best correlated with P availability and increased with experimental N addition only in lower C (mineral) soils with N:P⩽16. Microbial community membership also varied with soil stoichiometry but not with N addition. Shotgun metagenome data revealed changes in community functions with increasing C turnover, including a shift from aromatic C to carbohydrate utilization accompanied by lower N uptake and P scavenging. Similar patterns of C, N and P acquisition, along with higher ribosomal RNA operon copy numbers, distinguished that microbial taxa positively correlated with C turnover. Considering such tradeoffs in genomic resource allocation patterns among taxa strengthened correlations between microbial community composition and C cycling, suggesting simplified guilds amenable to ecosystem modeling. Our results suggest that patterns of soil C turnover may reflect community-dependent metabolic shifts driven by resource allocation strategies, analogous to growth rate-stoichiometry coupling in animal and plant communities.

  12. The Role of Hydrogen Bonds Of The Azeotropic Hydrous Ethanol Fuel Composition To The Exhaust Emissions

    NASA Astrophysics Data System (ADS)

    Made Suarta, I.; Nyoman Gede Baliarta, I.; Sopan Rahtika, I. P. G.; Wijaya Sunu, Putu

    2018-01-01

    In this study observed the role of hydrogen bonding to the composition of exhaust emissions which is produced hydrous ethanol fuel (95.5% v). Testing is done by using single cylinder four stroke motor engine. The composition of exhaust gas emissions is tested using exhaust gas analyzer on lean and stoichiometry mixer. The exhaust emissions produced by anhydrous ethanol were also tested. The composition of emissions produced by that two fuels is compared. The results showed CO emissions levels produced by hydrous ethanol are slightly higher than anhydrous ethanol in stoichiometric mixtures. But the composition of CO hydrous ethanol emissions is lower in the lean mix. If lean the mixer the different in the composition of emissions is increasing. On hydrous ethanol emission CO2 content little bit lower on the stoichiometric mixer and higher on the lean mixture. Exhaust emissions of ethanol fuel also produce O2. O2 hydrous ethanol emissions is higher than anhydrous ethanol fuel.

  13. Stoichiometric Lithium Niobate (SLN) Based Linearized Electro-Optic (EO) Modulator

    DTIC Science & Technology

    2006-01-01

    AFRL-SN-RS-TR-2006-15 Final Technical Report January 2006 STOICHIOMETRIC LITHIUM NIOBATE (SLN) BASED LINEARIZED ELECTRO - OPTIC (EO...LITHIUM NIOBATE (SLN) BASED LINEARIZED ELECTRO - OPTIC (EO) MODULATOR 6. AUTHOR(S) Dr Stuart Kingsley, Dr Sri Sriram 5. FUNDING NUMBERS C...SUBJECT TERMS electro - optic modulator, linearization, directional coupler, variable coupling, optical waveguide, Mach-Zehnder, photonic link, lithium

  14. Linking Stoichiometric Homeostasis of Microorganisms with Soil Phosphorus Dynamics in Wetlands Subjected to Microcosm Warming

    PubMed Central

    Wang, Hang; Li, HongYi; Zhang, ZhiJian; Muehlbauer, Jeffrey D.; He, Qiang; Xu, XinHua; Yue, ChunLei; Jiang, DaQian

    2014-01-01

    Soil biogeochemical processes and the ecological stability of wetland ecosystems under global warming scenarios have gained increasing attention worldwide. Changes in the capacity of microorganisms to maintain stoichiometric homeostasis, or relatively stable internal concentrations of elements, may serve as an indicator of alterations to soil biogeochemical processes and their associated ecological feedbacks. In this study, an outdoor computerized microcosm was set up to simulate a warmed (+5°C) climate scenario, using novel, minute-scale temperature manipulation technology. The principle of stoichiometric homeostasis was adopted to illustrate phosphorus (P) biogeochemical cycling coupled with carbon (C) dynamics within the soil-microorganism complex. We hypothesized that enhancing the flux of P from soil to water under warming scenarios is tightly coupled with a decrease in homeostatic regulation ability in wetland ecosystems. Results indicate that experimental warming impaired the ability of stoichiometric homeostasis (H) to regulate biogeochemical processes, enhancing the ecological role of wetland soil as an ecological source for both P and C. The potential P flux from soil to water ranged from 0.11 to 34.51 mg m−2 d−1 in the control and 0.07 to 61.26 mg m−2 d−1 in the warmed treatment. The synergistic function of C-P acquisition is an important mechanism underlying C∶P stoichiometric balance for soil microorganisms under warming. For both treatment groups, strongly significant (p<0.001) relationships fitting a negative allometric power model with a fractional exponent were found between n-HC∶P (the specialized homeostatic regulation ability as a ratio of soil highly labile organic carbon to dissolved reactive phosphorus in porewater) and potential P flux. Although many factors may affect soil P dynamics, the n-HC∶P term fundamentally reflects the stoichiometric balance or interactions between the energy landscape (i.e., C) and flow of resources

  15. Sex Education and Ideals

    ERIC Educational Resources Information Center

    de Ruyter, Doret J.; Spiecker, Ben

    2008-01-01

    This article argues that sex education should include sexual ideals. Sexual ideals are divided into sexual ideals in the strict sense and sexual ideals in the broad sense. It is argued that ideals that refer to the context that is deemed to be most ideal for the gratification of sexual ideals in the strict sense are rightfully called sexual…

  16. Stoichiometric patterns in foliar nutrient resorption across multiple scales

    USGS Publications Warehouse

    Reed, Sasha C.; Townsend, Alan R.; Davidson, Eric A.; Cleveland, Cory C.

    2012-01-01

    *Nutrient resorption is a fundamental process through which plants withdraw nutrients from leaves before abscission. Nutrient resorption patterns have the potential to reflect gradients in plant nutrient limitation and to affect a suite of terrestrial ecosystem functions. *Here, we used a stoichiometric approach to assess patterns in foliar resorption at a variety of scales, specifically exploring how N : P resorption ratios relate to presumed variation in N and/or P limitation and possible relationships between N : P resorption ratios and soil nutrient availability. *N : P resorption ratios varied significantly at the global scale, increasing with latitude and decreasing with mean annual temperature and precipitation. In general, tropical sites (absolute latitudes < 23°26′) had N : P resorption ratios of < 1, and plants growing on highly weathered tropical soils maintained the lowest N : P resorption ratios. Resorption ratios also varied with forest age along an Amazonian forest regeneration chronosequence and among species in a diverse Costa Rican rain forest. *These results suggest that variations in N : P resorption stoichiometry offer insight into nutrient cycling and limitation at a variety of spatial scales, complementing other metrics of plant nutrient biogeochemistry. The extent to which the stoichiometric flexibility of resorption will help regulate terrestrial responses to global change merits further investigation.

  17. Global dynamics in a stoichiometric food chain model with two limiting nutrients.

    PubMed

    Chen, Ming; Fan, Meng; Kuang, Yang

    2017-07-01

    Ecological stoichiometry studies the balance of energy and multiple chemical elements in ecological interactions to establish how the nutrient content affect food-web dynamics and nutrient cycling in ecosystems. In this study, we formulate a food chain with two limiting nutrients in the form of a stoichiometric population model. A comprehensive global analysis of the rich dynamics of the targeted model is explored both analytically and numerically. Chaotic dynamic is observed in this simple stoichiometric food chain model and is compared with traditional model without stoichiometry. The detailed comparison reveals that stoichiometry can reduce the parameter space for chaotic dynamics. Our findings also show that decreasing producer production efficiency may have only a small effect on the consumer growth but a more profound impact on the top predator growth. Copyright © 2017 Elsevier Inc. All rights reserved.

  18. Elastin: a representative ideal protein elastomer.

    PubMed Central

    Urry, D W; Hugel, T; Seitz, M; Gaub, H E; Sheiba, L; Dea, J; Xu, J; Parker, T

    2002-01-01

    During the last half century, identification of an ideal (predominantly entropic) protein elastomer was generally thought to require that the ideal protein elastomer be a random chain network. Here, we report two new sets of data and review previous data. The first set of new data utilizes atomic force microscopy to report single-chain force-extension curves for (GVGVP)(251) and (GVGIP)(260), and provides evidence for single-chain ideal elasticity. The second class of new data provides a direct contrast between low-frequency sound absorption (0.1-10 kHz) exhibited by random-chain network elastomers and by elastin protein-based polymers. Earlier composition, dielectric relaxation (1-1000 MHz), thermoelasticity, molecular mechanics and dynamics calculations and thermodynamic and statistical mechanical analyses are presented, that combine with the new data to contrast with random-chain network rubbers and to detail the presence of regular non-random structural elements of the elastin-based systems that lose entropic elastomeric force upon thermal denaturation. The data and analyses affirm an earlier contrary argument that components of elastin, the elastic protein of the mammalian elastic fibre, and purified elastin fibre itself contain dynamic, non-random, regularly repeating structures that exhibit dominantly entropic elasticity by means of a damping of internal chain dynamics on extension. PMID:11911774

  19. Shock wave structure in an ideal dissociating gas

    NASA Technical Reports Server (NTRS)

    Liu, K. H.

    1975-01-01

    Composition changes within the shock layer due to chemical reactions are considered. The Lighthill ideal dissociating gas model was used in an effort to describe the oxygen type molecule. First, the two limiting cases, when the chemical reaction rates are very slow and very fast in comparison to local convective rates, are investigated. Then, the problem is solved for arbitrary chemical reaction rates.

  20. Ultranarrow Optical Inhomogeneous Linewidth in a Stoichiometric Rare-Earth Crystal.

    PubMed

    Ahlefeldt, R L; Hush, M R; Sellars, M J

    2016-12-16

    We obtain a low optical inhomogeneous linewidth of 25 MHz in the stoichiometric rare-earth crystal EuCl_{3}·6H_{2}O by isotopically purifying the crystal in ^{35}Cl. With this linewidth, an important limit for stoichiometric rare-earth crystals is surpassed: the hyperfine structure of ^{153}Eu is spectrally resolved, allowing the whole population of ^{153}Eu^{3+} ions to be prepared in the same hyperfine state using hole-burning techniques. This material also has a very high optical density, and can have long coherence times when deuterated. This combination of properties offers new prospects for quantum information applications. We consider two of these: quantum memories and quantum many-body studies. We detail the improvements in the performance of current memory protocols possible in these high optical depth crystals, and describe how certain memory protocols, such as off-resonant Raman memories, can be implemented for the first time in a solid-state system. We explain how the strong excitation-induced interactions observed in this material resemble those seen in Rydberg systems, and describe how these interactions can lead to quantum many-body states that could be observed using standard optical spectroscopy techniques.

  1. Exhaust particle characterization for lean and stoichiometric DI vehicles operating on ethanol-gasoline blends

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Storey, John Morse; Barone, Teresa L; Thomas, John F

    2012-01-01

    Gasoline direct injection (GDI) engines can offer better fuel economy and higher performance over their port fuel-injected (PFI) counterparts, and are now appearing in increasingly more U.S. and European vehicles. Small displacement, turbocharged GDI engines are replacing large displacement engines, particularly in light-duty trucks and sport utility vehicles, in order for manufacturers to meet the U.S. fuel economy standards for 2016. Furthermore, lean-burn GDI engines can offer even higher fuel economy than stoichiometric GDI engines and have overcome challenges associated with cost-effective aftertreatment for NOx control. Along with changes in gasoline engine technology, fuel composition may increase in ethanol contentmore » beyond the current 10% due to the recent EPA waiver allowing 15% ethanol. In addition, the Renewable Fuels Standard passed as part of the 2007 Energy Independence and Security Act (EISA) mandates the use of biofuels in upcoming years. GDI engines are of environmental concern due to their high particulate matter (PM) emissions relative to port-fuel injected (PFI) gasoline vehicles; widespread market penetration of GDI vehicles may result in additional PM from mobile sources at a time when the diesel contribution is declining. In this study, we characterized particulate emissions from a European certified lean-burn GDI vehicle operating on ethanol-gasoline blends. Particle mass and particle number concentration emissions were measured for the Federal Test Procedure urban driving cycle (FTP 75) and the more aggressive US06 driving cycle. Particle number-size distributions and organic to elemental carbon ratios (OC/EC) were measured for 30 MPH and 80 MPH steady-state operation. In addition, particle number concentration was measured during wide open throttle accelerations (WOTs) and gradual accelerations representative of the FTP 75. Fuels included certification gasoline and 10% (E10) and 20% (E20) ethanol blends from the same supplier. The

  2. Problem Solving Instruction for Overcoming Students' Difficulties in Stoichiometric Problems

    ERIC Educational Resources Information Center

    Shadreck, Mandina; Enunuwe, Ochonogor Chukunoye

    2017-01-01

    The study sought to find out difficulties encountered by high school chemistry students when solving stoichiometric problems and how these could be overcome by using a problem-solving approach. The study adopted a quasi-experimental design. 485 participants drawn from 8 highs schools in a local education district in Zimbabwe participated in the…

  3. Freshwater bacteria are stoichiometrically flexible with a nutrient composition similar to seston

    USGS Publications Warehouse

    Cotner, James B.; Hall, Edward K.; Scott, J. Thad; Heldal, Mikal

    2010-01-01

    Although aquatic bacteria are assumed to be nutrient-rich, they out-compete other foodweb osmotrophs for nitrogen (N) and phosphorus (P) an apparent contradiction to resource ratio theory. This paradox could be resolved if aquatic bacteria were demonstrated to be nutrient-poor relative other portions of the planktonic food web. In a survey of >120 lakes in the upper Midwest of the USA, the nutrient content of bacteria was lower than previously reported and very similar to the Redfield ratio, with a mean biomass composition of 102:12:1 (C:N:P). Individual freshwater bacterial isolates grown under P-limiting and P-replete conditions had even higher C:P and N:P ratios with a mean community biomass composition ratio of 875C:179N:1P suggesting that individual strains can be extremely nutrient-poor, especially with respect to P. Cell-specific measurements of individual cells from one lake confirmed that low P content could be observed at the community level in natural systems with a mean biomass composition of 259C:69N:1P. Variability in bacterial stoichiometry is typically not recognized in the literature as most studies assume constant and nutrient-rich bacterial biomass composition. We present evidence that bacteria can be extremely P-poor in individual systems and in culture, suggesting that bacteria in freshwater ecosystems can either play a role as regenerators or consumers of inorganic nutrients and that this role could switch depending on the relationship between bacterial biomass stoichiometry and resource stoichiometry. This ability to switch roles between nutrient retention and regeneration likely facilitates processing of terrestrial organic matter in lakes and rivers and has important implications for a wide range of bacterially mediated biogeochemical processes.

  4. Nodeless multiband superconductivity in stoichiometric single-crystalline CaKFe 4 As 4

    DOE PAGES

    Cho, Kyuil; Fente, A.; Teknowijoyo, S.; ...

    2017-03-08

    Measurements of the London penetration depth Δλ(T) and tunneling conductance in single crystals of the recently discovered stoichiometric iron-based superconductor CaKFe 4As 4 (CaK1144) show nodeless, two-effective-gap superconductivity with a larger gap of about 6–10 meV and a smaller gap of about 1–4 meV. Having a critical temperature T c,onset ≈ 35.8 K, this material behaves similar to slightly overdoped (Ba 1–xK x)Fe 2As 2 (e.g., x = 0.54,T c ≈ 34 K), a known multigap s ± superconductor. Here, we conclude that the superconducting behavior of stoichiometric CaK1144 demonstrates that two-gap s± superconductivity is an essential property of high-temperaturemore » superconductivity in iron-based superconductors, independent of the degree of substitutional disorder.« less

  5. An optimality framework to predict decomposer carbon-use efficiency trends along stoichiometric gradients

    NASA Astrophysics Data System (ADS)

    Manzoni, S.; Capek, P.; Mooshammer, M.; Lindahl, B.; Richter, A.; Santruckova, H.

    2016-12-01

    Litter and soil organic matter decomposers feed on substrates with much wider C:N and C:P ratios then their own cellular composition, raising the question as to how they can adapt their metabolism to such a chronic stoichiometric imbalance. Here we propose an optimality framework to address this question, based on the hypothesis that carbon-use efficiency (CUE) can be optimally adjusted to maximize the decomposer growth rate. When nutrients are abundant, increasing CUE improves decomposer growth rate, at the expense of higher nutrient demand. However, when nutrients are scarce, increased nutrient demand driven by high CUE can trigger nutrient limitation and inhibit growth. An intermediate, `optimal' CUE ensures balanced growth at the verge of nutrient limitation. We derive a simple analytical equation that links this optimal CUE to organic substrate and decomposer biomass C:N and C:P ratios, and to the rate of inorganic nutrient supply (e.g., fertilization). This equation allows formulating two specific hypotheses: i) decomposer CUE should increase with widening organic substrate C:N and C:P ratios with a scaling exponent between 0 (with abundant inorganic nutrients) and -1 (scarce inorganic nutrients), and ii) CUE should increase with increasing inorganic nutrient supply, for a given organic substrate stoichiometry. These hypotheses are tested using a new database encompassing nearly 2000 estimates of CUE from about 160 studies, spanning aquatic and terrestrial decomposers of litter and more stabilized organic matter. The theoretical predictions are largely confirmed by our data analysis, except for the lack of fertilization effects on terrestrial decomposer CUE. While stoichiometric drivers constrain the general trends in CUE, the relatively large variability in CUE estimates suggests that other factors could be at play as well. For example, temperature is often cited as a potential driver of CUE, but we only found limited evidence of temperature effects

  6. Methanol oxidation on stoichiometric and oxygen-rich RuO2(110).

    PubMed

    Rai, Rahul; Weaver, Jason F

    2017-07-26

    We used temperature-programmed reaction spectroscopy (TPRS) to investigate the adsorption and oxidation of methanol on stoichiometric and O-rich RuO 2 (110) surfaces. We find that the complete oxidation of CH 3 OH is strongly preferred on stoichiometric RuO 2 (110) during TPRS for initial CH 3 OH coverages below ∼0.33 ML (monolayer), and that partial oxidation to mainly CH 2 O becomes increasingly favored with increasing CH 3 OH coverage from 0.33 to 1.0 ML. We present evidence that an adsorbed CH 2 O 2 species serves as the key intermediate to complete oxidation and that CH 2 O 2 formation is intrinsically facile but becomes limited by the availability of bridging O-atoms on stoichiometric RuO 2 (110) at initial CH 3 OH coverages above 0.33 ML. We show that methanol molecules adsorbed in excess of 0.33 ML dehydrogenate to mainly CH 2 O and desorb during TPRS, with adsorbed CH 3 O groups mediating the evolution of both CH 2 O and CH 3 OH. We find that O-rich RuO 2 (110) surfaces are also highly active toward methanol oxidation and that selectivity toward the complete oxidation of methanol increases markedly with increasing coverage of on-top O-atoms (O ot ) on RuO 2 (110). Our results demonstrate that CH 3 OH species adsorbed within O ot -rich domains react efficiently during TPRS, in parallel with reaction of CH 3 OH adsorbed initially on cus-Ru sites. The data suggests that the facile hydrogenation of O ot atoms and the resulting desorption of H 2 O at low-temperature (<∼400 K) provides an efficient pathway for restoring reactive O-atoms and thereby promoting complete oxidation of methanol on the O-rich RuO 2 (110) surface.

  7. Stoichiometric determination of nitrate fate in agricultural ecosystems during rainfall events.

    PubMed

    Xu, Zuxin; Wang, Yiyao; Li, Huaizheng

    2015-01-01

    Ecologists have found a close relationship between the concentrations of nitrate (NO3-) and dissolved organic carbon (DOC) in ecosystems. However, it is difficult to determine the NO3- fate exactly because of the low coefficient in the constructed relationship. In the present paper, a negative power-function equation (r(2) = 0.87) was developed by using 411 NO3- data points and DOC:NO3- ratios from several agricultural ecosystems during different rainfall events. Our analysis of the stoichiometric method reveals several observations. First, the NO3- concentration demonstrated the largest changes when the DOC:NO3- ratio increased from 1 to 10. Second, the biodegradability of DOC was an important factor in controlling the NO3- concentration of agricultural ecosystems. Third, sediment was important not only as a denitrification site, but also as a major source of DOC for the overlying water. Fourth, a high DOC concentration was able to maintain a low NO3- concentration in the groundwater. In conclusion, this new stoichiometric method can be used for the accurate estimation and analysis of NO3- concentrations in ecosystems.

  8. Twin defects in thick stoichiometric lithium tantalate crystals prepared by a vapor transport equilibration method

    NASA Astrophysics Data System (ADS)

    Yang, Jinfeng; Sun, Jun; Xu, Jingjun; Li, Qinglian; Shang, Jifang; Zhang, Ling; Liu, Shiguo; Huang, Cunxin

    2016-01-01

    The twins were observed and investigated in vapor transport equilibration (VTE) treated lithium tantalate crystals by burying congruent lithium tantalate crystals (CLT) in a Li-rich polycrystalline powder. Twins and their etched patterns were observed under an optical polarizing microscope, and the geometry of the twins was discussed. Twin composition planes were the { 01 1 bar 2 } planes. The cause of twinning was analyzed and verified by experiment. The results indicate that the emergence of twins is due to sintering stress, which arises from sintered Li-rich polycrystalline powders at high temperature. 3.2 mm thick stoichiometric lithium tantalate (SLT) crystals without twins were obtained by setting corundum crucibles over the top of the crystals to make crystals free from the sintering stress. In addition, cracks were observed at the intersection of twin bands, and the stress caused by the dislocation pile-up was considered to be the reason for the formation of cracks.

  9. Electronic and spin structure of the wide-band-gap topological insulator: Nearly stoichiometric Bi2Te2S

    NASA Astrophysics Data System (ADS)

    Annese, E.; Okuda, T.; Schwier, E. F.; Iwasawa, H.; Shimada, K.; Natamane, M.; Taniguchi, M.; Rusinov, I. P.; Eremeev, S. V.; Kokh, K. A.; Golyashov, V. A.; Tereshchenko, O. E.; Chulkov, E. V.; Kimura, A.

    2018-05-01

    We have grown the phase-homogeneous ternary compound with composition Bi2Te1.85S1.15 very close to the stoichiometric Bi2Te2S . The measurements performed with spin- and angle-resolved photoelectron spectroscopy as well as density functional theory and G W calculations revealed a wide-band-gap three-dimensional topological insulator phase. The surface electronic spectrum is characterized by the topological surface state (TSS) with Dirac point located above the valence band and Fermi level lying in the band gap. TSS band dispersion and constant energy contour manifest a weak warping effect near the Fermi level along with in-plane and out-of-plane spin polarization along the Γ ¯-K ¯ line. We identified four additional states at deeper binding energies with high in-plane spin polarization.

  10. Evidence for the bias-driven migration of oxygen vacancies in amorphous non-stoichiometric gallium oxide

    NASA Astrophysics Data System (ADS)

    Guo, D. Y.; Qian, Y. P.; Su, Y. L.; Shi, H. Z.; Li, P. G.; Wu, J. T.; Wang, S. L.; Cui, C.; Tang, W. H.

    2017-06-01

    The conductivity of gallium oxide thin films is strongly dependent on the growth temperature when they deposited by pulsed laser deposition under vacuum environment, exhibiting an insulative-to-metallic transition with the decrease of the temperature. The high conductive gallium oxide films deposited at low temperature are amorphous, non-stoichiometric, and rich in oxygen vacancy. Large changes in electrical resistance are observed in these non-stoichiometric thin films. The wide variety of hysteretic shapes in the I-V curves depend on the voltage-sweep rate, evidencing that the time-dependent redistribution of oxygen vacancy driven by bias is the controlling parameter for the resistance of gallium oxide.

  11. Photoluminescence properties of non-stoichiometric strontium zirconate powder phosphor

    NASA Astrophysics Data System (ADS)

    Jarý, V.; Boháček, P.; Mihóková, E.; Havlák, L.; Trunda, B.; Nikl, M.

    2013-03-01

    Excitation and emission spectra and decay kinetics of non-stoichiometric strontium zirconate powder phosphor were measured in the 8-500 K temperature interval. Phenomenological model was applied to extract quantitative parameters of the excited state levels and nonradiative quenching pathways related to the luminescence centre. Delayed recombination integrals measurement was employed to investigate the occurrence of thermally induced ionization of the excited state of the emission centre. The nature of the emission centre itself is suggested. Suitability for phosphor and scintillation application is discussed.

  12. Performance and emission characteristics of swirl-can combustors to near-stoichiometric fuel-air ratio

    NASA Technical Reports Server (NTRS)

    Diehl, L. A.; Trout, A. M.

    1976-01-01

    Emissions and performance characteristics were determined for two full annular swirl-can combustors operated to near stoichiometric fuel-air ratio. Test condition variations were as follows: combustor inlet-air temperatures, 589, 756, 839, and 894 K; reference velocities, 24 to 37 meters per second; inlet pressure, 62 newtons per square centimeter; and fuel-air ratios, 0.015 to 0.065. The combustor average exit temperature and combustor efficiency were calculated from the combustor exhaust gas composition. For fuel-air ratios greater than 0.04, the combustion efficiency decreased with increasing fuel-air ratios in a near-linear manner. Increasing the combustor inlet air temperature tended to offset this decrease. Maximum oxides of nitrogen emission indices occurred at intermediate fuel-air ratios and were dependent on combustor design. Carbon monoxide levels were extremely high and were the primary cause of poor combustion efficiency at the higher fuel-air ratios. Unburned hydrocarbons were low for all test conditions. For high fuel-air ratios SAE smoke numbers greater than 25 were produced, except at the highest inlet-air temperatures.

  13. Tuning cationic composition of La:EuTiO{sub 3−δ} films

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Shkabko, Andrey, E-mail: shkabko@gmail.com; Empa, Solid State Chemistry and Catalysis, CH-8600 Dübendorf; Xu, Chencheng

    2013-11-01

    Eu{sub 1−x}La{sub x}TiO{sub 3−δ} (x = 0, 0.3, 0.5) films were deposited in a p(Ar(96%)/H{sub 2}(4%)) = 4 × 10{sup −4} mbar atmosphere on (LaAlO{sub 3}){sub 0.3}-(Sr{sub 2}AlTaO{sub 6}){sub 0.7} vicinal substrates (0.1°). Reflection high-energy electron diffraction oscillation characteristics of a layer-by-layer growth mode were observed for stoichiometric and Ti-rich films and the laser fluence suited to deposit stoichiometric films was identified to be 1.25 J/cm{sup 2} independent of the La content. The variety of resulting film compositions follows the general trend of Eu-enrichment for low laser and Ti-enrichment for high laser fluence. X-ray diffraction confirms that all the filmsmore » are compressively strained with a general trend of an increase of c-axis elongation for non-stoichiometric films. The surfaces of non-stoichiometric films have an increased roughness, the highest sheet resistances, exhibit the presence of islands, and are Eu{sup 3+} rich for films deposited at low laser fluence.« less

  14. Ideals versus reality: Are weight ideals associated with weight change in the population?

    PubMed

    Kärkkäinen, Ulla; Mustelin, Linda; Raevuori, Anu; Kaprio, Jaakko; Keski-Rahkonen, Anna

    2016-04-01

    To quantify weight ideals of young adults and to examine whether the discrepancy between actual and ideal weight is associated with 10-year body mass index (BMI) change in the population. This study comprised 4,964 adults from the prospective population-based FinnTwin16 study. They reported their actual and ideal body weight at age 24 (range 22-27) and 10 years later (attrition 24.6%). The correlates of discrepancy between actual and ideal body weight and the impact on subsequent BMI change were examined. The discrepancy between actual and ideal weight at 24 years was on average 3.9 kg (1.4 kg/m(2) ) among women and 1.2 kg (0.4 kg/m(2) ) among men. On average, participants gained weight during follow-up irrespective of baseline ideal weight: women ¯x = +4.8 kg (1.7 kg/m(2) , 95% CI 1.6-1.9 kg/m(2) ), men ¯x = +6.3 kg (2.0 kg/m(2) , 95% CI 1.8-2.1 kg/m(2) ). Weight ideals at 24 years were not correlated with 10-year weight change. At 34 years, just 13.2% of women and 18.9% of men were at or below the weight they had specified as their ideal weight at 24 years. Women and men adjusted their ideal weight upward over time. Irrespective of ideal weight at baseline, weight gain was nearly universal. Weight ideals were shifted upward over time. © 2016 The Obesity Society.

  15. Socioeconomic status and parenting during adolescence in relation to ideal cardiovascular health in Black and White men.

    PubMed

    Matthews, Karen A; Boylan, Jennifer M; Jakubowski, Karen P; Cundiff, Jenny M; Lee, Laisze; Pardini, Dustin A; Jennings, J Richard

    2017-07-01

    American Heart Association (AHA) developed a new metric to evaluate ideal cardiovascular health based on optimal levels of 7 cardiovascular risk factors and health behaviors. We evaluated the relationships of parenting characteristics and academic achievement in adolescence in relation to ideal cardiovascular health in midlife men. We measured cardiovascular risk factors in 171 Black and 136 White men and their ideal cardiovascular health score was constructed based on AHA guidelines. When the participants were 13-16 years old, annual measures of parent-child communication, positive relationship, parental monitoring, family cohesion, boys' involvement in family activities, and academic achievement were recorded and averaged. Confirmatory factor analysis of adolescent parenting measures revealed a single Parenting Composite. Multiple linear regressions showed a significant Race by Parenting Composite interaction term, β = -.19, p = .03; better parenting was significantly related to more ideal cardiovascular health in Blacks only, β = -.23, p = .004, which remained after adjustments for adolescent and adult socioeconomic status (SES). Academic achievement was related to ideal cardiovascular health, β = -.13, but was no longer significant after controls for adult SES. Adult SES was a strong correlate of ideal cardiovascular health in Black and White men. Black men exposed to positive parenting during adolescence had more ideal cardiovascular health based on AHA guidelines. Improving academic achievement in adolescence may indirectly benefit adult cardiovascular health through improving adult SES. This is the first study of adolescent family predictors of the extent of ideal cardiovascular health. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

  16. Ideal cardiovascular health and its association with sedentary behaviour and fitness in psychiatric patients. The PsychiActive project.

    PubMed

    Bueno-Antequera, J; Oviedo-Caro, M Á; Munguía-Izquierdo, D

    2018-06-10

    Ideal cardiovascular health (CVH) was defined as meeting ideal levels of 4 health behaviours (smoking, body mass index, physical activity, and diet) and 3 biological factors (blood pressure, total cholesterol, and glucose) and is inversely related to cardiovascular disease and mortality. However, the prevalence of ideal CVH in patients with severe mental illness and the possible independent associations of sedentary behaviour and fitness with CVH score are unexplored. This study included 142 (34 women) outpatients with severe mental illness (primarily schizophrenia, n = 92). CVH was evaluated according to the American Heart Association guidelines. Sedentary behaviour, cardiorespiratory fitness, and muscular strength were measured by an activity-monitor, the 6-min walk test, and handgrip dynamometry. Cardiorespiratory fitness and strength values were combined in a composite fitness score. The prevalence of ideal CVH was: non-smoking (47.9%), body mass index (16.9), physical activity (83.1%), diet (10.4%), blood pressure (40.4%), total cholesterol (62.9%), and plasma glucose (66.7%). Low levels of sedentary behaviour and high cardiorespiratory, strength, and composite fitness score were associated with meeting the ideal threshold in most CVH metrics and having higher global CVH score; however, only cardiorespiratory and composite fitness score remained significantly related to global CVH score independent of sedentary behaviour and multiple confounders. Patients with severe mental illness generally have low prevalence of ideal CVH metrics, especially diet and body mass index. Additionally, our findings suggest the need or considering cardiorespiratory fitness, regardless of sedentary behaviour, to promote ideal CVH in this population. Copyright © 2018 The Italian Society of Diabetology, the Italian Society for the Study of Atherosclerosis, the Italian Society of Human Nutrition, and the Department of Clinical Medicine and Surgery, Federico II University. Published

  17. Model-based metabolism design: constraints for kinetic and stoichiometric models

    PubMed Central

    Stalidzans, Egils; Seiman, Andrus; Peebo, Karl; Komasilovs, Vitalijs; Pentjuss, Agris

    2018-01-01

    The implementation of model-based designs in metabolic engineering and synthetic biology may fail. One of the reasons for this failure is that only a part of the real-world complexity is included in models. Still, some knowledge can be simplified and taken into account in the form of optimization constraints to improve the feasibility of model-based designs of metabolic pathways in organisms. Some constraints (mass balance, energy balance, and steady-state assumption) serve as a basis for many modelling approaches. There are others (total enzyme activity constraint and homeostatic constraint) proposed decades ago, but which are frequently ignored in design development. Several new approaches of cellular analysis have made possible the application of constraints like cell size, surface, and resource balance. Constraints for kinetic and stoichiometric models are grouped according to their applicability preconditions in (1) general constraints, (2) organism-level constraints, and (3) experiment-level constraints. General constraints are universal and are applicable for any system. Organism-level constraints are applicable for biological systems and usually are organism-specific, but these constraints can be applied without information about experimental conditions. To apply experimental-level constraints, peculiarities of the organism and the experimental set-up have to be taken into account to calculate the values of constraints. The limitations of applicability of particular constraints for kinetic and stoichiometric models are addressed. PMID:29472367

  18. (Fuzzy) Ideals of BN-Algebras

    PubMed Central

    Walendziak, Andrzej

    2015-01-01

    The notions of an ideal and a fuzzy ideal in BN-algebras are introduced. The properties and characterizations of them are investigated. The concepts of normal ideals and normal congruences of a BN-algebra are also studied, the properties of them are displayed, and a one-to-one correspondence between them is presented. Conditions for a fuzzy set to be a fuzzy ideal are given. The relationships between ideals and fuzzy ideals of a BN-algebra are established. The homomorphic properties of fuzzy ideals of a BN-algebra are provided. Finally, characterizations of Noetherian BN-algebras and Artinian BN-algebras via fuzzy ideals are obtained. PMID:26125050

  19. Two-Dimensional Stoichiometric Boron Oxides as a Versatile Platform for Electronic Structure Engineering.

    PubMed

    Zhang, Ruiqi; Li, Zhenyu; Yang, Jinlong

    2017-09-21

    Oxides of two-dimensional (2D) atomic crystals have been widely studied due to their unique properties. In most 2D oxides, oxygen acts as a functional group, which makes it difficult to control the degree of oxidation. Because borophene is an electron-deficient system, it is expected that oxygen will be intrinsically incorporated into the basal plane of borophene, forming stoichiometric 2D boron oxide (BO) structures. By using first-principles global optimization, we systematically explore structures and properties of 2D BO systems with well-defined degrees of oxidation. Stable B-O-B and OB 3 tetrahedron structure motifs are identified in these structures. Interesting properties, such as strong linear dichroism, Dirac node-line (DNL) semimetallicity, and negative differential resistance, have been predicted for these systems. Our results demonstrate that 2D BO represents a versatile platform for electronic structure engineering via tuning the stoichiometric degree of oxidation, which leads to various technological applications.

  20. Development of an impact- and solvent-resistant thermoplastic composite matrix, phase 4

    NASA Technical Reports Server (NTRS)

    Delano, C. B.

    1987-01-01

    Polyimides from BTDA with m-phenylenediamine and three aliphatic diamines were prepared in cresol and characterized. Characterization tests included compression strength and modulus, stressed solvent resistance, and melt-flow tests. Efforts to reduce the molecular weights of these polymers by either stoichiometric imbalance or phthalic anhydride end capping produced opacity in the polymer moldings when the stoichiometry was less than 99 percent. Use of 2,4-diaminotoluene in place of the m-phenylenediamine allowed clear polymer moldings to be obtained at all stoichiometries by end capping or stoichiometric imbalance. After melt-flow/molecular-weight studies, carbon fabric composites were prepared from three polyimide compositions containing BTDA, 2,4-diaminotoluene and two aliphatic diamines. Flexural strengths of two of the resins were in excess of 689 MPa (100 ksi) at both room temperature and 93 C. The polyimide from BTDA was selected for scale-up and neat resin characterization tests. The Tg of this polymer was 233 C.

  1. Stoichiometric vs hydroclimatic controls on soil biogeochemical processes

    NASA Astrophysics Data System (ADS)

    Manzoni, Stefano; Porporato, Amilcare

    2010-05-01

    Soil nutrient cycles are controlled by both stoichiometric constraints (e.g., carbon to nutrient ratios) and hydroclimatic conditions (e.g., soil moisture and temperature). Both controls tend to act in a nonlinear manner and give rise to complex dynamics in soil biogeochemistry at different space-time scales. We first review the theoretical basis of soil biogeochemical models, looking for the general principles underlying these models across space-time scales and scientific disciplines. By comparing more than 250 models, we show that similar kinetic and stoichiometric laws, formulated to mechanistically represent the complex biochemical constraints to decomposition, are common to most models, providing a basis for their classification. Moreover, a historic analysis reveals that the complexity (e.g., phase space dimension, model architecture) and degree and number of nonlinearities generally increased with date, while they decreased with increasing spatial and temporal scale of interest. Soil biogeochmical dynamics may be suitable conceptualized using a number of compartments (e.g., decomposers, organic substrates, inorganic ions) interacting among each other at rates that depend (nonlinearly) on climatic drivers. As a consequence, hydroclimatic-induced fluctuations at the daily scale propagate through the various soil compartments leading to cascading effects ranging from short-term fluctuations in the smaller pools to long-lasting changes in the larger ones. Such cascading effects are known to occur in dryland ecosystems, and are increasingly being recongnized to control the long-term carbon and nutrient balances in more mesic ecosystems. We also show that separating biochemical from climatic impacts on organic matter decomposition results in universal curves describing data of plant residue decomposition and nutrient mineralization across the globe. Future extensions to larger spatial scales and managed ecosystems are also briefly outlined. It is critical that

  2. A novel strategy for pharmaceutical cocrystal generation without knowledge of stoichiometric ratio: myricetin cocrystals and a ternary phase diagram.

    PubMed

    Hong, Chao; Xie, Yan; Yao, Yashu; Li, Guowen; Yuan, Xiurong; Shen, Hongyi

    2015-01-01

    To develop a streamlined strategy for pharmaceutical cocrystal preparation without knowledge of the stoichiometric ratio by preparing and characterizing the cocrystals of myricetin (MYR) with four cocrystal coformers (CCF). An approach based on the phase solubility diagram (PSD) was used for MYR cocrystals preparation and the solid-state properties were characterized by differential scanning calorimetry (DSC), fourier transform-infrared spectroscopy (FT-IR), powder X-ray diffraction (PXRD), and scanning electron microscopy (SEM). The ternary phase diagram (TPD) was constructed by combining the PSD and nuclear magnetic resonance (NMR) data. After that, the TPD was verified by traditional methods. The dissolution of MYR in the four cocrystals and pure MYR within three different media were also evaluated. A simple research method for MYR cocrystal preparation was obtained as follows: first, the PSD of MYR and CCF was constructed and analyzed; second, by transforming the curve in the PSD to a TPD, a region of pure cocrystals formation was exhibited, and then MYR cocrystals were prepared and identified by DSC, FT-IR, PXRD, and SEM; third, with the composition of the prepared cocrystal from NMR, the TPD of the MYR-CCF-Solvent system was constructed. The powder dissolution data showed that the solubility and dissolution rate of MYR was significantly enhanced by the cocrystals. A novel strategy for pharmaceutical cocrystals preparation without knowledge of the stoichiometric ratio based on the TPD was established and MYR cocrystals were successfully prepared. The present study provides a systematic approach for pharmaceutical cocrystal generation, which benefits the development and application of cocrystal technology in drug delivery.

  3. Effects of tetraamine crosslinking agents on the thermomechanical properties of PMR polyimide composites

    NASA Technical Reports Server (NTRS)

    Delvigs, P.

    1976-01-01

    The effects were investigated of partial substitution of tetraamine crosslinking agents for diamine reactants on the thermomechanical properties of PMR polyimide resins and graphite fiber-reinforced composites. The effect of tetraamine content on isothermal weight loss, glass transition, and softening temperatures of neat resin samples is discussed. Composites were fabricated using PMR methodology. Monomeric solution of various stoichiometric ratios was used to impregnate Hercules HTS graphite fiber. The mechanical property retention characteristics of the composites at 316 C (600 F) are described.

  4. Assessment of environmentally friendly fuel emissions from in-use vehicle exhaust: low-blend iso-stoichiometric GEM mixture as example.

    PubMed

    Schifter, Isaac; Díaz-Gutiérrez, Luis; Rodríguez-Lara, René; González-Macías, Carmen; González-Macías, Uriel

    2017-05-01

    Gasoline-ethanol-methanol fuel blends were formulated with the same stoichiometric air-to-fuel ratio and volumetric energy concentration as any binary ethanol-gasoline blend. When the stoichiometric blends operated in a vehicle, the time period, injector voltage, and pressure for each fuel injection event in the engine corresponded to a given stoichiometric air-to-fuel ratio, and the load was essentially constant. Three low oxygen content iso-stoichiometric ternary gasoline-ethanol-methanol fuel blends were prepared, and the properties were compared with regular-type fuel without added oxygen. One of the ternary fuels was tested using a fleet of in-use vehicles for15 weeks and compared to neat gasoline without oxygenated compounds as a reference. Only a small number of publications have compared these ternary fuels in the same engine, and little data exist on the performance and emissions of in-use spark-ignition engines. The total hydrocarbon emissions observed was similar in both fuels, in addition to the calculated ozone forming potential of the tailpipe and evaporative emissions. In ozone non-attainment areas, the original purpose for oxygenate gasolines was to decrease carbon monoxide emissions. The results suggest that the strategy is less effective than expected because there still exist a great number of vehicles that have suffered the progressive deterioration of emissions and do not react to oxygenation, while new vehicles are equipped with sophisticated air/fuel control systems, and oxygenation does not improve combustion because the systems adjust the stoichiometric point, making it insensitive to the origin of the added excess oxygen (fuel or excess air). Graphical abstract Low level ternary blend of gasoline-ethanol-methanol were prepared with the same stoichiometric air-fuel ratio and volumetric energy concentration, based on the volumetric energy density of the pre-blended components. Exhaust and evaporative emissions was compared with a blend

  5. Correlates of elemental-isotopic composition of stream fishes: the importance of land-use, species identity and body size.

    PubMed

    Montaña, C G; Schalk, C M

    2018-04-01

    The isotopic (δ 13 C and δ 15 N) and stoichiometric (C:N:P) compositions of four fish species (Family Centrarchidae: Lepomis auritus, Lepomis cyanellus; Family Cyprinidae: Nocomis leptocephalus, Semotilus atromaculatus) were examined across four North Carolina Piedmont streams arrayed along an urbanization gradient. Both isotopic and stoichiometric composition of fishes appeared to track changes occurring in basal resource availability. Values of δ 13 C of basal resources and consumers were more enriched at the most urbanized streams. Similarly, basal resources and consumers were δ 15 N-enriched at more urbanized streams. Basal resource stoichiometry varied across streams, with periphyton being the most variable. Primary consumers stoichiometry also differed across streams. Intraspecific variation in fish stoichiometry correlated with the degree of urbanization, as the two cyprinids had higher N content and L. cyanellus had higher P content in more urbanized streams, probably due to enrichment of basal resources. Intrinsic factors, specifically species identity and body size also affected stoichiometric variation. Phosphorus (P) content increased significantly with body size in centrarchids, but not in cyprinids. These results suggest that although species identity and body size are important predictors of elemental stoichiometry, the complex nature of altered urban streams may yield imbalances in the elemental composition of consumers via their food resources. © 2018 The Fisheries Society of the British Isles.

  6. Stability and cellular responses to fluorapatite-collagen composites.

    PubMed

    Yoon, Byung-Ho; Kim, Hae-Won; Lee, Su-Hee; Bae, Chang-Jun; Koh, Young-Hag; Kong, Young-Min; Kim, Hyoun-Ee

    2005-06-01

    Fluorapatite (FA)-collagen composites were synthesized via a biomimetic coprecipitation method in order to improve the structural stability and cellular responses. Different amounts of ammonium fluoride (NH4F), acting as a fluorine source for FA, were added to the precipitation of the composites. The precipitated composites were freeze-dried and isostatically pressed in a dense body. The added fluorine was incorporated nearly fully into the apatite structure (fluoridation), and a near stoichiometric FA-collagen composite was obtained with complete fluoridation. The freeze-dried composites had a typical biomimetic network, consisting of collagen fibers and precipitates of nano-sized apatite crystals. The human osteoblast-like cells on the FA-collagen composites exhibited significantly higher proliferation and differentiation (according to alkaline phosphatase activity) than those on the hydroxyapatite-collagen composite. These enhanced osteoblastic cell responses were attributed to the fluorine release and the reduced dissolution rate.

  7. Novel polyelectrolyte complex based carbon nanotube composite architectures

    NASA Astrophysics Data System (ADS)

    Razdan, Sandeep

    This study focuses on creating novel architectures of carbon nanotubes using polyelectrolytes. Polyelectrolytes are unique polymers possessing resident charges on the macromolecular chains. This property, along with their biocompatibility (true for most polymers used in this study) makes them ideal candidates for a variety of applications such as membranes, drug delivery systems, scaffold materials etc. Carbon nanotubes are also unique one-dimensional nanoscale materials that possess excellent electrical, mechanical and thermal properties owing to their small size, high aspect ratio, graphitic structure and strength arising from purely covalent bonds in the molecular structure. The present study tries to investigate the synthesis processes and material properties of carbon nanotube composites comprising of polyelectrolyte complexes. Carbon nanotubes are dispersed in a polyelectrolyte and are induced into taking part in a complexation process with two oppositely charged polyelectrolytes. The resulting stoichiometric precipitate is then drawn into fiber form and dried as such. The material properties of the carbon nanotube fibers were characterized and related to synthesis parameters and material interactions. Also, an effort was made to understand and predict fiber morphology resulting from the complexation and drawing process. The study helps to delineate the synthesis and properties of the said polyelectrolyte complex-carbon nanotube architectures and highlights useful properties, such as electrical conductivity and mechanical strength, which could make these structures promising candidates for a variety of applications.

  8. Stoichiometric Effects on the Photoelectric Properties of LiInSe 2 Crystals for Neutron Detection

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Guo, Lijian; Xu, Yadong; Zheng, Hongjian

    6LiInSe 2 is a promising semiconductor candidate for thermal neutron detection due to its large capture cross-section. However, the charge collection efficiency is still insufficient for high resolution for the grown-in defects induced by the stoichiometric deviation. In this work, we report photoelectric properties of stoichiometric LiInSe 2 crystal boules up to 70 mm in length and 20 mm in diameter grown by the vertical Bridgman method. Inductively coupled plasma measurements demonstrate that the ratio of Li, In, and Se of the as-grown crystal is very close to 1:1:2, which is optimized by low temperature synthesis processing. The obtained singlemore » crystals display high bulk resistivity in the range of 10 11–10 12 Ω·cm and a direct band gap of 2.01–2.83 eV with a changeable color from red to yellow. The electronic structure of LiInSe 2 was studied using first-principles density functional theory calculations, which predicts that the antisite defects of In Li and Li In are the dominant factor for the different crystal colors observed. The stoichiometric LiInSe 2 crystal gives an improved energy resolution, for a semiconductor detector when illuminated with a 241Am@5.48 MeV α source, of 23.3%. In conclusion, the electron mobility-lifetime product (μτ) is ~2.5 × 10 –5 cm 2 V –1.« less

  9. Stoichiometric Effects on the Photoelectric Properties of LiInSe 2 Crystals for Neutron Detection

    DOE PAGES

    Guo, Lijian; Xu, Yadong; Zheng, Hongjian; ...

    2018-04-16

    6LiInSe 2 is a promising semiconductor candidate for thermal neutron detection due to its large capture cross-section. However, the charge collection efficiency is still insufficient for high resolution for the grown-in defects induced by the stoichiometric deviation. In this work, we report photoelectric properties of stoichiometric LiInSe 2 crystal boules up to 70 mm in length and 20 mm in diameter grown by the vertical Bridgman method. Inductively coupled plasma measurements demonstrate that the ratio of Li, In, and Se of the as-grown crystal is very close to 1:1:2, which is optimized by low temperature synthesis processing. The obtained singlemore » crystals display high bulk resistivity in the range of 10 11–10 12 Ω·cm and a direct band gap of 2.01–2.83 eV with a changeable color from red to yellow. The electronic structure of LiInSe 2 was studied using first-principles density functional theory calculations, which predicts that the antisite defects of In Li and Li In are the dominant factor for the different crystal colors observed. The stoichiometric LiInSe 2 crystal gives an improved energy resolution, for a semiconductor detector when illuminated with a 241Am@5.48 MeV α source, of 23.3%. In conclusion, the electron mobility-lifetime product (μτ) is ~2.5 × 10 –5 cm 2 V –1.« less

  10. Neutron spectroscopic study of crystalline electric field excitations in stoichiometric and lightly stuffed Yb 2 Ti 2 O 7

    DOE PAGES

    Gaudet, J.; Maharaj, D. D.; Sala, G.; ...

    2015-10-27

    Time-of-flight neutron spectroscopy has been used to determine the crystalline electric field Hamiltonian, eigenvalues and eigenvectors appropriate to the J=7/2 Yb 3+ ion in the candidate quantum spin ice pyrochlore magnet Yb 2Ti 2O 7. The precise ground state of this exotic, geometrically frustrated magnet is known to be sensitive to weak disorder associated with the growth of single crystals from the melt. Such materials display weak “stuffing,” wherein a small proportion, approximately 2%, of the nonmagnetic Ti 4+ sites are occupied by excess Yb 3+. We have carried out neutron spectroscopic measurements on a stoichiometric powder sample of Ybmore » 2Ti 2O 7, as well as a crushed single crystal with weak stuffing and an approximate composition of Yb 2+xTi 2–xO 7+y with x = 0.046. All samples display three crystalline electric field transitions out of the ground state, and the ground state doublet itself is identified as primarily composed of m J = ±1/2, as expected. However, stuffing at low temperatures in Yb 2+xTi 2–xO 7+y induces a similar finite crystalline electric field lifetime as is induced in stoichiometric Yb 2Ti 2O 7 by elevated temperature. In conclusion, an extended strain field exists about each local “stuffed” site, which produces a distribution of random crystalline electric field environments in the lightly stuffed Yb 2+xTi 2–xO 7+y, in addition to producing a small fraction of Yb ions in defective environments with grossly different crystalline electric field eigenvalues and eigenvectors.« less

  11. Targeted Proteomics and Absolute Protein Quantification for the Construction of a Stoichiometric Host-Pathogen Surface Density Model*

    PubMed Central

    Sjöholm, Kristoffer; Kilsgård, Ola; Teleman, Johan; Happonen, Lotta; Malmström, Lars; Malmström, Johan

    2017-01-01

    Sepsis is a systemic immune response responsible for considerable morbidity and mortality. Molecular modeling of host-pathogen interactions in the disease state represents a promising strategy to define molecular events of importance for the transition from superficial to invasive infectious diseases. Here we used the Gram-positive bacterium Streptococcus pyogenes as a model system to establish a mass spectrometry based workflow for the construction of a stoichiometric surface density model between the S. pyogenes surface, the surface virulence factor M-protein, and adhered human blood plasma proteins. The workflow relies on stable isotope labeled reference peptides and selected reaction monitoring mass spectrometry analysis of a wild-type strain and an M-protein deficient mutant strain, to generate absolutely quantified protein stoichiometry ratios between S. pyogenes and interacting plasma proteins. The stoichiometry ratios in combination with a novel targeted mass spectrometry method to measure cell numbers enabled the construction of a stoichiometric surface density model using protein structures available from the protein data bank. The model outlines the topology and density of the host-pathogen protein interaction network on the S. pyogenes bacterial surface, revealing a dense and highly organized protein interaction network. Removal of the M-protein from S. pyogenes introduces a drastic change in the network topology, validated by electron microscopy. We propose that the stoichiometric surface density model of S. pyogenes in human blood plasma represents a scalable framework that can continuously be refined with the emergence of new results. Future integration of new results will improve the understanding of protein-protein interactions and their importance for bacterial virulence. Furthermore, we anticipate that the general properties of the developed workflow will facilitate the production of stoichiometric surface density models for other types of host

  12. Targeted Proteomics and Absolute Protein Quantification for the Construction of a Stoichiometric Host-Pathogen Surface Density Model.

    PubMed

    Sjöholm, Kristoffer; Kilsgård, Ola; Teleman, Johan; Happonen, Lotta; Malmström, Lars; Malmström, Johan

    2017-04-01

    Sepsis is a systemic immune response responsible for considerable morbidity and mortality. Molecular modeling of host-pathogen interactions in the disease state represents a promising strategy to define molecular events of importance for the transition from superficial to invasive infectious diseases. Here we used the Gram-positive bacterium Streptococcus pyogenes as a model system to establish a mass spectrometry based workflow for the construction of a stoichiometric surface density model between the S. pyogenes surface, the surface virulence factor M-protein, and adhered human blood plasma proteins. The workflow relies on stable isotope labeled reference peptides and selected reaction monitoring mass spectrometry analysis of a wild-type strain and an M-protein deficient mutant strain, to generate absolutely quantified protein stoichiometry ratios between S. pyogenes and interacting plasma proteins. The stoichiometry ratios in combination with a novel targeted mass spectrometry method to measure cell numbers enabled the construction of a stoichiometric surface density model using protein structures available from the protein data bank. The model outlines the topology and density of the host-pathogen protein interaction network on the S. pyogenes bacterial surface, revealing a dense and highly organized protein interaction network. Removal of the M-protein from S. pyogenes introduces a drastic change in the network topology, validated by electron microscopy. We propose that the stoichiometric surface density model of S. pyogenes in human blood plasma represents a scalable framework that can continuously be refined with the emergence of new results. Future integration of new results will improve the understanding of protein-protein interactions and their importance for bacterial virulence. Furthermore, we anticipate that the general properties of the developed workflow will facilitate the production of stoichiometric surface density models for other types of host

  13. The Place of Ideals in Teaching.

    ERIC Educational Resources Information Center

    Hansen, David T.

    This paper examines whether ideals and idealism have a role to play in teaching, identifying some ambiguities and problems associated with ideals and arguing that ideals figure importantly in teaching, but they are ideals of character or personhood as much as they are ideals of educational purpose. The first section focuses on the promise and…

  14. C, N and P fertilization in an Amazonian rainforest supports stoichiometric dissimilarity as a driver of litter diversity effects on decomposition

    PubMed Central

    Barantal, Sandra; Schimann, Heidy; Fromin, Nathalie; Hättenschwiler, Stephan

    2014-01-01

    Plant leaf litter generally decomposes faster as a group of different species than when individual species decompose alone, but underlying mechanisms of these diversity effects remain poorly understood. Because resource C : N : P stoichiometry (i.e. the ratios of these key elements) exhibits strong control on consumers, we supposed that stoichiometric dissimilarity of litter mixtures (i.e. the divergence in C : N : P ratios among species) improves resource complementarity to decomposers leading to faster mixture decomposition. We tested this hypothesis with: (i) a wide range of leaf litter mixtures of neotropical tree species varying in C : N : P dissimilarity, and (ii) a nutrient addition experiment (C, N and P) to create stoichiometric similarity. Litter mixtures decomposed in the field using two different types of litterbags allowing or preventing access to soil fauna. Litter mixture mass loss was higher than expected from species decomposing singly, especially in presence of soil fauna. With fauna, synergistic litter mixture effects increased with increasing stoichiometric dissimilarity of litter mixtures and this positive relationship disappeared with fertilizer addition. Our results indicate that litter stoichiometric dissimilarity drives mixture effects via the nutritional requirements of soil fauna. Incorporating ecological stoichiometry in biodiversity research allows refinement of the underlying mechanisms of how changing biodiversity affects ecosystem functioning. PMID:25320173

  15. Synthesis, Hardness, and Electronic Properties of Stoichiometric VN and CrN

    DOE PAGES

    Wang, Shanmin; Yu, Xiaohui; Zhang, Jianzhong; ...

    2015-11-09

    Here, we report synthesis of single-crystal VN and CrN through high-pressure ionexchange reaction routes. The final products are stoichiometric and have crystallite sizes in the range of 50-120 mu m. We also prepared VN and TiN crystals using high-pressure sintering of nitride powders. On the basis of single-crystal indentation testing, the determined asymptotic Vickers hardness for TiN, VN, and CrN is 18 (1), 10 (1), and 16 (1) GPa, respectively. Moreover, the relatively low hardness in VN indicates that the metallic bonding prevails due to the overfilled metallic a bonds, although the cation-anion covalent hybridization in this compound is muchmore » stronger than that in TiN and CrN. All three nitrides are intrinsically excellent metals at ambient pressure. In particular, VN exhibits superconducting transition at T-c approximate to 7.8 K, which is slightly lower than the reported values for nitrogen-deficient or crystallinedisordered samples due to unsuppressed "spin fluctuation" in the well-crystallized stoichiometric VN. The magnetostructural transition in CrN correlates with a metal metal transition at T-N = 240(5) K and is accompanied by a similar to 40% drop in electrical resistivity. Additionally, more detailed electronic properties are presented with new insights into these nitrides.« less

  16. Density Functional Studies of Stoichiometric Surfaces of Orthorhombic Hybrid Perovskite CH3NH3PbI3

    DOE PAGES

    Wang, Yun; Huang, Jingsong; Sumpter, Bobby G.; ...

    2014-12-19

    Organic/inorganic hybrid perovskite materials are highly attractive for dye-sensitized solar cells as demonstrated by their rapid advances in energy conversion efficiency. In this work, the structures, energetics, and electronic properties for a range of stoichiometric surfaces of the orthorhombic perovskite CH3NH3PbI3 are theoretically studied using density functional theory. Various possible spatially and constitutionally isomeric surfaces are considered by diversifying the spatial orientations and connectivities of surface Pb-I bonds. The comparison of the surface energies for the most stable configurations identified for various surfaces shows that the stabilities of stoichiometric surfaces are mainly dictated by the coordination numbers of surface atoms,more » which are directly correlated with the numbers of broken bonds. Additionally, Coulombic interactions between I anions and organic countercations on the surface also contribute to the stabilization. Electronic properties are compared between the most stable (100) surface and the bulk phase, showing generally similar features except for the lifted band degeneracy and the enhanced bandgap energy for the surface. These studies on the stoichiometric surfaces serve as the first step toward gaining a fundamental understanding of the interfacial properties in the current structural design of perovskite based solar cells, in order to achieve further breakthroughs in solar conversion efficiencies.« less

  17. Medical ethics and more: ideal theories, non-ideal theories and conscientious objection.

    PubMed

    Luna, Florencia

    2015-01-01

    Doing 'good medical ethics' requires acknowledgment that it is often practised in non-ideal circumstances! In this article I present the distinction between ideal theory (IT) and non-ideal theory (NIT). I show how IT may not be the best solution to tackle problems in non-ideal contexts. I sketch a NIT framework as a useful tool for bioethics and medical ethics and explain how NITs can contribute to policy design in non-ideal circumstances. Different NITs can coexist and be evaluated vis-à-vis the IT. Additionally, I address what an individual doctor ought to do in this non-ideal context with the view that knowledge of NITs can facilitate the decision-making process. NITs help conceptualise problems faced in the context of non-compliance and scarcity in a better and more realistic way. Deciding which policy is optimal in such contexts may influence physicians' decisions regarding their patients. Thus, this analysis-usually identified only with policy making-may also be relevant to medical ethics. Finally, I recognise that this is merely a first step in an unexplored but fundamental theoretical area and that more work needs to be done. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

  18. Detonation failure characterization of non-ideal explosives

    NASA Astrophysics Data System (ADS)

    Janesheski, Robert S.; Groven, Lori J.; Son, Steven

    2012-03-01

    Non-ideal explosives are currently poorly characterized, hence limiting the modeling of them. Current characterization requires large-scale testing to obtain steady detonation wave characterization for analysis due to the relatively thick reaction zones. Use of a microwave interferometer applied to small-scale confined transient experiments is being implemented to allow for time resolved characterization of a failing detonation. The microwave interferometer measures the position of a failing detonation wave in a tube that is initiated with a booster charge. Experiments have been performed with ammonium nitrate and various fuel compositions (diesel fuel and mineral oil). It was observed that the failure dynamics are influenced by factors such as chemical composition and confiner thickness. Future work is planned to calibrate models to these small-scale experiments and eventually validate the models with available large scale experiments. This experiment is shown to be repeatable, shows dependence on reactive properties, and can be performed with little required material.

  19. Developmental Idealism in China

    PubMed Central

    Thornton, Arland; Xie, Yu

    2016-01-01

    This paper examines the intersection of developmental idealism with China. It discusses how developmental idealism has been widely disseminated within China and has had enormous effects on public policy and programs, on social institutions, and on the lives of individuals and their families. This dissemination of developmental idealism to China began in the 19th century, when China met with several military defeats that led many in the country to question the place of China in the world. By the beginning of the 20th century, substantial numbers of Chinese had reacted to the country’s defeats by exploring developmental idealism as a route to independence, international respect, and prosperity. Then, with important but brief aberrations, the country began to implement many of the elements of developmental idealism, a movement that became especially important following the assumption of power by the Communist Party of China in 1949. This movement has played a substantial role in politics, in the economy, and in family life. The beliefs and values of developmental idealism have also been directly disseminated to the grassroots in China, where substantial majorities of Chinese citizens have assimilated them. These ideas are both known and endorsed by very large numbers in China today. PMID:28316833

  20. Developmental Idealism in China.

    PubMed

    Thornton, Arland; Xie, Yu

    2016-10-01

    This paper examines the intersection of developmental idealism with China. It discusses how developmental idealism has been widely disseminated within China and has had enormous effects on public policy and programs, on social institutions, and on the lives of individuals and their families. This dissemination of developmental idealism to China began in the 19 th century, when China met with several military defeats that led many in the country to question the place of China in the world. By the beginning of the 20 th century, substantial numbers of Chinese had reacted to the country's defeats by exploring developmental idealism as a route to independence, international respect, and prosperity. Then, with important but brief aberrations, the country began to implement many of the elements of developmental idealism, a movement that became especially important following the assumption of power by the Communist Party of China in 1949. This movement has played a substantial role in politics, in the economy, and in family life. The beliefs and values of developmental idealism have also been directly disseminated to the grassroots in China, where substantial majorities of Chinese citizens have assimilated them. These ideas are both known and endorsed by very large numbers in China today.

  1. Reference of Temperature and Time during tempering process for non-stoichiometric FTO films

    NASA Astrophysics Data System (ADS)

    Yang, J. K.; Liang, B.; Zhao, M. J.; Gao, Y.; Zhang, F. C.; Zhao, H. L.

    2015-10-01

    In order to enhance the mechanical strength of Low-E glass, Fluorine-doped tin oxide (FTO) films have to be tempered at high temperatures together with glass substrates. The effects of tempering temperature (600 °C ~ 720 °C) and time (150 s ~ 300 s) on the structural and electrical properties of FTO films were investigated. The results show all the films consist of non-stoichiometric, polycrystalline SnO2 without detectable amounts of fluoride. 700 °C and 260 s may be the critical tempering temperature and time, respectively. FTO films tempered at 700 °C for 260 s possesses the resistivity of 7.54 × 10-4 Ω•cm, the average transmittance in 400 ~ 800 nm of ~80%, and the calculated emissivity of 0.38. Hall mobility of FTO films tempered in this proper condition is mainly limited by the ionized impurity scattering. The value of [O]/[Sn] at the film surface is much higher than the stoichiometric value of 2.0 of pure crystalline SnO2.

  2. C, N and P fertilization in an Amazonian rainforest supports stoichiometric dissimilarity as a driver of litter diversity effects on decomposition.

    PubMed

    Barantal, Sandra; Schimann, Heidy; Fromin, Nathalie; Hättenschwiler, Stephan

    2014-12-07

    Plant leaf litter generally decomposes faster as a group of different species than when individual species decompose alone, but underlying mechanisms of these diversity effects remain poorly understood. Because resource C : N : P stoichiometry (i.e. the ratios of these key elements) exhibits strong control on consumers, we supposed that stoichiometric dissimilarity of litter mixtures (i.e. the divergence in C : N : P ratios among species) improves resource complementarity to decomposers leading to faster mixture decomposition. We tested this hypothesis with: (i) a wide range of leaf litter mixtures of neotropical tree species varying in C : N : P dissimilarity, and (ii) a nutrient addition experiment (C, N and P) to create stoichiometric similarity. Litter mixtures decomposed in the field using two different types of litterbags allowing or preventing access to soil fauna. Litter mixture mass loss was higher than expected from species decomposing singly, especially in presence of soil fauna. With fauna, synergistic litter mixture effects increased with increasing stoichiometric dissimilarity of litter mixtures and this positive relationship disappeared with fertilizer addition. Our results indicate that litter stoichiometric dissimilarity drives mixture effects via the nutritional requirements of soil fauna. Incorporating ecological stoichiometry in biodiversity research allows refinement of the underlying mechanisms of how changing biodiversity affects ecosystem functioning. © 2014 The Author(s) Published by the Royal Society. All rights reserved.

  3. Comprehensive analysis of proton range uncertainties related to patient stopping-power-ratio estimation using the stoichiometric calibration

    PubMed Central

    Yang, M; Zhu, X R; Park, PC; Titt, Uwe; Mohan, R; Virshup, G; Clayton, J; Dong, L

    2012-01-01

    The purpose of this study was to analyze factors affecting proton stopping-power-ratio (SPR) estimations and range uncertainties in proton therapy planning using the standard stoichiometric calibration. The SPR uncertainties were grouped into five categories according to their origins and then estimated based on previously published reports or measurements. For the first time, the impact of tissue composition variations on SPR estimation was assessed and the uncertainty estimates of each category were determined for low-density (lung), soft, and high-density (bone) tissues. A composite, 95th percentile water-equivalent-thickness uncertainty was calculated from multiple beam directions in 15 patients with various types of cancer undergoing proton therapy. The SPR uncertainties (1σ) were quite different (ranging from 1.6% to 5.0%) in different tissue groups, although the final combined uncertainty (95th percentile) for different treatment sites was fairly consistent at 3.0–3.4%, primarily because soft tissue is the dominant tissue type in human body. The dominant contributing factor for uncertainties in soft tissues was the degeneracy of Hounsfield Numbers in the presence of tissue composition variations. To reduce the overall uncertainties in SPR estimation, the use of dual-energy computed tomography is suggested. The values recommended in this study based on typical treatment sites and a small group of patients roughly agree with the commonly referenced value (3.5%) used for margin design. By using tissue-specific range uncertainties, one could estimate the beam-specific range margin by accounting for different types and amounts of tissues along a beam, which may allow for customization of range uncertainty for each beam direction. PMID:22678123

  4. A new multidimensional stoichiometric classification of compounds: moving beyond the van Krevelen diagram.

    NASA Astrophysics Data System (ADS)

    Rivas-Ubach, A.; Liu, Y.; Bianchi, T. S.; Tolic, N.; Jansson, C.; Paša-Tolić, L.

    2017-12-01

    The role of nutrients in organisms, especially primary producers, has been a topic of special interest in ecosystem research for understanding the ecosystem structure and function. The majority of macro-elements in organisms, such as C, H, O, N and P, do not act as single elements but are components of organic compounds (lipids, peptides, carbohydrates, etc), which are more directly related to the physiology of organisms and thus to the ecosystem function. However, accurately deciphering the overall content of the main compound classes (lipids, proteins, carbohydrates,…) in organisms is still a major challenge. van Krevelen (vK) diagrams have been widely used as an estimation of the main compound categories present in environmental samples based on O:C vs H:C molecular ratios, but a stoichiometric classification based exclusively on O:C and H:C ratios is feeble. Different compound classes show large O:C and H:C ratio overlapping and other heteroatoms, such as N and P, should be considered to robustly distinguish the different classes. We propose a new compound classification for biological/environmental samples based on the C:H:O:N:P stoichiometric ratios of thousands of molecular formulas of characterized compounds from 6 different main categories: lipids, peptides, amino-sugars, carbohydrates, nucleotides and phytochemical compounds (oxy-aromatic compounds). This new multidimensional stoichiometric compound constraints classification (MSCC) can be applied to data obtained with high resolution mass spectrometry (HRMS), allowing an accurate overview of the relative abundances of the main compound categories present in organismal samples. The MSCC has been optimized for plants, but it could be also applied to different organisms and serve as a strong starting point to further investigate other environmental complex matrices (soils, aerosols, etc). The proposed MSCC advances environmental research, especially eco-metabolomics, ecophysiology and ecological

  5. Creep Behavior of Near-Stoichiometric Polycrystalline Binary NiAl

    NASA Technical Reports Server (NTRS)

    Raj, S. V.

    2002-01-01

    New and published constant load creep and constant engineering strain rate data on near-stoichiometric binary NiAl in the intermediate temperature range 700 to 1300 K are reviewed. Both normal and inverse primary creep curves are observed depending on stress and temperature. Other characteristics relating to creep of NiAl involving grain size, stress and temperature dependence are critically examined and discussed. At stresses below 25 MPa and temperatures above 1000 K, a new grain boundary sliding mechanism was observed with n approx. 2, Qc approx. 100 kJ/ mol and a grain size exponent of about 2. It is demonstrated that Coble creep and accommodated grain boundary sliding models fail to predict the experimental creep rates by several orders of magnitude.

  6. [C, N and P stoichiometric characteristics of different root orders for three dominant tree species in subalpine forests of western Sichuan, China].

    PubMed

    Tang, Shi-shan; Yang, Wan-qin; Xiong, Li; Yin, Rui; Wang, Hai-peng; Zhang, Yan; Xu, Zhen-feng

    2015-02-01

    Fine root order was classified according to Pregitzer's method. This study measured carbon (C), nitrogen (N) and phosphorus (P) concentrations of the 1-5 root orders (diameter < 2 mm) in three dominant subalpine tree species (Betula albosinensis, Abies faxoniana and Picea asperata) of western Sichuan. Their stoichiometric ratios of different root orders were also calculated. The results showed that C concentration, C/N and C/P increased, but N and P concentrations decreased from the first to fifth order of fine root for all tree species. No significant changes in N/P among root orders were detected in each species. There were significant differences in C, N, P concentrations and their stoichiometric ratios among the tree species. The species-associated differences were dependent on root order. There were significant correlations between C, N, P concentrations and their stoichiometric ratios in the three tree species.

  7. Zero-Field Ambient-Pressure Quantum Criticality in the Stoichiometric Non-Fermi Liquid System CeRhBi

    NASA Astrophysics Data System (ADS)

    Anand, Vivek K.; Adroja, Devashibhai T.; Hillier, Adrian D.; Shigetoh, Keisuke; Takabatake, Toshiro; Park, Je-Geun; McEwen, Keith A.; Pixley, Jedediah H.; Si, Qimiao

    2018-06-01

    We present the spin dynamics study of a stoichiometric non-Fermi liquid (NFL) system CeRhBi, using low-energy inelastic neutron scattering (INS) and muon spin relaxation (μSR) measurements. It shows evidence for an energy-temperature (E/T) scaling in the INS dynamic response and a time-field (t/Hη) scaling of the μSR asymmetry function indicating a quantum critical behavior in this compound. The E/T scaling reveals a local character of quantum criticality consistent with the power-law divergence of the magnetic susceptibility, logarithmic divergence of the magnetic heat capacity and T-linear resistivity at low temperature. The occurrence of NFL behavior and local criticality over a very wide dynamical range at zero field and ambient pressure without any tuning in this stoichiometric heavy fermion compound is striking, making CeRhBi a model system amenable to in-depth studies for quantum criticality.

  8. Steps Towards Industrialization of Cu–III–VI2Thin‐Film Solar Cells:Linking Materials/Device Designs to Process Design For Non‐stoichiometric Photovoltaic Materials

    PubMed Central

    Chang, Hsueh‐Hsin; Sharma, Poonam; Letha, Arya Jagadhamma; Shao, Lexi; Zhang, Yafei; Tseng, Bae‐Heng

    2016-01-01

    The concept of in‐line sputtering and selenization become industrial standard for Cu–III–VI2 solar cell fabrication, but still it's very difficult to control and predict the optical and electrical parameters, which are closely related to the chemical composition distribution of the thin film. The present review article addresses onto the material design, device design and process design using parameters closely related to the chemical compositions. Its variation leads to change in the Poisson equation, current equation, and continuity equation governing the device design. To make the device design much realistic and meaningful, we need to build a model that relates the opto‐electrical properties to the chemical composition. The material parameters as well as device structural parameters are loaded into the process simulation to give a complete set of process control parameters. The neutral defect concentrations of non‐stoichiometric CuMSe2 (M = In and Ga) have been calculated under the specific atomic chemical potential conditions using this methodology. The optical and electrical properties have also been investigated for the development of a full‐function analytical solar cell simulator. The future prospects regarding the development of copper–indium–gallium–selenide thin film solar cells have also been discussed. PMID:27840790

  9. Steps Towards Industrialization of Cu-III-VI2Thin-Film Solar Cells:Linking Materials/Device Designs to Process Design For Non-stoichiometric Photovoltaic Materials.

    PubMed

    Hwang, Huey-Liang; Chang, Hsueh-Hsin; Sharma, Poonam; Letha, Arya Jagadhamma; Shao, Lexi; Zhang, Yafei; Tseng, Bae-Heng

    2016-10-01

    The concept of in-line sputtering and selenization become industrial standard for Cu-III-VI 2 solar cell fabrication, but still it's very difficult to control and predict the optical and electrical parameters, which are closely related to the chemical composition distribution of the thin film. The present review article addresses onto the material design, device design and process design using parameters closely related to the chemical compositions. Its variation leads to change in the Poisson equation, current equation, and continuity equation governing the device design. To make the device design much realistic and meaningful, we need to build a model that relates the opto-electrical properties to the chemical composition. The material parameters as well as device structural parameters are loaded into the process simulation to give a complete set of process control parameters. The neutral defect concentrations of non-stoichiometric CuMSe 2 (M = In and Ga) have been calculated under the specific atomic chemical potential conditions using this methodology. The optical and electrical properties have also been investigated for the development of a full-function analytical solar cell simulator. The future prospects regarding the development of copper-indium-gallium-selenide thin film solar cells have also been discussed.

  10. Influence of free carbon on the characteristics of ZrC and deposition of near-stoichiometric ZrC in TRISO coated particle fuel

    NASA Astrophysics Data System (ADS)

    Kim, Daejong; Ko, Myeong Jin; Park, Ji Yeon; Cho, Moon Sung; Kim, Weon-Ju

    2014-08-01

    Advanced TRISO coated particles with a ZrC coating layer as a main pressure boundary were fabricated by a fluidized-bed chemical vapor deposition (FBCVD) method using a chloride process. Experiments were performed to determine the effect of codeposition of graphitic carbon on the hardness and obtain the stoichiometric ZrC phase. The ZrC coating layer was composed of a mixture of ZrC and graphitic carbon phases at a low ZrCl4/CH4 ratio. A near-stoichiometric ZrC without the free carbon can be obtained by employing an impeller-driven ZrCl4 vaporizer. The codeposition of the graphitic carbon significantly lowered the hardness of ZrC while increasing the fraction of the carbon. The hardness reached its maximum when ZrC was in a slight carbon deficit without free carbon. As the graphitic carbon increased up to 12 vol%, the hardness was reduced by approximately 50% compared to the near-stoichiometric ZrC.

  11. Influence of NiO on the crystallization kinetics of near stoichiometric cordierite glasses nucleated with TiO2

    NASA Astrophysics Data System (ADS)

    Goel, Ashutosh; Shaaban, Essam R.; Ribeiro, Manuel J.; Melo, Francisco C. L.; Ferreira, José M. F.

    2007-09-01

    This work presents the effect of NiO on the thermal behavior and the crystallization kinetics of glasses lying near the stoichiometric cordierite composition nucleated with TiO2. Three glasses with NiO content varying between 1 and 5 mol% have been synthesized in Pt crucibles. Activation energies for structural relaxation and viscous flow have been calculated using the data obtained from differential thermal analysis (DTA). Kinetic fragility of the glasses along with other thermal parameters has been calculated. Non-isothermal crystallization kinetic studies have been employed to study the mechanism of crystallization in all three glasses. The crystallization sequence in the glasses has been followed by x-ray diffraction analysis of the heat treated glass samples in the temperature range of 800-1200 °C. μ-cordierite has been observed to be the first crystalline phase in all the glass samples after heat treatment at 850 °C, while NiO plays an important role in determining the crystallization sequence at higher temperatures, leading to the formation of α-cordierite.

  12. Investigation of trimethylacetic acid adsorption on stoichiometric and oxygen-deficient CeO 2 (111) surfaces

    DOE PAGES

    Sanghavi, Shail; Wang, Weina; Nandasiri, Manjula I.; ...

    2016-05-12

    We studied the interactions between the carboxylate anchoring group from trimethylacetic acid (TMAA) and CeO 2(111) surfaces as a function of oxygen stoichiometry using in situ X-ray photoelectron spectroscopy (XPS). The stoichiometric CeO 2(111) surface was obtained by annealing the thin film under 2.0 × 10 –5 Torr of oxygen at ~550 °C for 30 min. In order to reduce the CeO 2(111) surface, the thin film was annealed under ~5.0 × 10 –10 Torr vacuum conditions at 550 °C, 650 °C, 750 °C and 850 °C for 30 min to progressively increase the oxygen defect concentration on the surface.more » The saturated TMAA coverage on the CeO 2(111) surface determined from XPS elemental composition is found to increase with increasing oxygen defect concentration. This is attributed to the increase of under-coordinated cerium sites on the surface with the increase in the oxygen defect concentrations. Furthermore, XPS results were in agreement with periodic density functional theory (DFT) calculations and indicate a stronger binding between the carboxylate group from TMAA and the oxygen deficient CeO 2–δ(111) surface through dissociative adsorption.« less

  13. A study of tumour growth based on stoichiometric principles: a continuous model and its discrete analogue.

    PubMed

    Saleem, M; Agrawal, Tanuja; Anees, Afzal

    2014-01-01

    In this paper, we consider a continuous mathematically tractable model and its discrete analogue for the tumour growth. The model formulation is based on stoichiometric principles considering tumour-immune cell interactions in potassium (K (+))-limited environment. Our both continuous and discrete models illustrate 'cancer immunoediting' as a dynamic process having all three phases namely elimination, equilibrium and escape. The stoichiometric principles introduced into the model allow us to study its dynamics with the variation in the total potassium in the surrounding of the tumour region. It is found that an increase in the total potassium may help the patient fight the disease for a longer period of time. This result seems to be in line with the protective role of the potassium against the risk of pancreatic cancer as has been reported by Bravi et al. [Dietary intake of selected micronutrients and risk of pancreatic cancer: An Italian case-control study, Ann. Oncol. 22 (2011), pp. 202-206].

  14. A study of tumour growth based on stoichiometric principles: a continuous model and its discrete analogue

    PubMed Central

    Saleem, M.; Agrawal, Tanuja; Anees, Afzal

    2014-01-01

    In this paper, we consider a continuous mathematically tractable model and its discrete analogue for the tumour growth. The model formulation is based on stoichiometric principles considering tumour-immune cell interactions in potassium (K +)-limited environment. Our both continuous and discrete models illustrate ‘cancer immunoediting’ as a dynamic process having all three phases namely elimination, equilibrium and escape. The stoichiometric principles introduced into the model allow us to study its dynamics with the variation in the total potassium in the surrounding of the tumour region. It is found that an increase in the total potassium may help the patient fight the disease for a longer period of time. This result seems to be in line with the protective role of the potassium against the risk of pancreatic cancer as has been reported by Bravi et al. [Dietary intake of selected micronutrients and risk of pancreatic cancer: An Italian case-control study, Ann. Oncol. 22 (2011), pp. 202–206]. PMID:24963981

  15. From the ideal market to the ideal clinic: constructing a normative standard of fairness for human subjects research.

    PubMed

    Phillips, Trisha

    2011-02-01

    Preventing exploitation in human subjects research requires a benchmark of fairness against which to judge the distribution of the benefits and burdens of a trial. This paper proposes the ideal market and its fair market price as a criterion of fairness. The ideal market approach is not new to discussions about exploitation, so this paper reviews Wertheimer's inchoate presentation of the ideal market as a principle of fairness, attempt of Emanuel and colleagues to apply the ideal market to human subjects research, and Ballantyne's criticisms of both the ideal market and the resulting benchmark of fairness. It argues that the criticism of this particular benchmark is on point, but the rejection of the ideal market is mistaken. After presenting a complete account of the ideal market, this paper proposes a new method for applying the ideal market to human subjects research and illustrates the proposal by considering a sample case.

  16. Vickers indentation hardness of stoichiometric and reduced single crystal TiO2 (rutile) from 25 to 800 C

    NASA Technical Reports Server (NTRS)

    Dellacorte, Christopher; Deadmore, Daniel L.

    1993-01-01

    The indentation microhardness of stoichiometric and reduced single crystal rutile (TiO2) from 25 to 800 C is presented in this paper. The results serve two main purposes. One is to assess the effect of rutile's stoichiometry on its hardness. The other is to test recently suggested theory on solid lubrication with sub Stoichiometric rutile in an effort to better understand shear controlled phenomenon. Microhardness was measured using a Vickers diamond indentor on both vacuum and hydrogen reduced single crystal rutile from 25 to 800 C. The results indicate that stoichiometry and temperature have a pronounced effect on rutile's hardness. The measured effects lend support to theory on solid lubrication by enhanced crystallographic slip and suggest that solid lubricant materials may be produced by careful atomic level tailoring (stoichiometry control).

  17. Ideals as Anchors for Relationship Experiences

    PubMed Central

    Frye, Margaret; Trinitapoli, Jenny

    2016-01-01

    Research on young-adult sexuality in sub-Saharan Africa typically conceptualizes sex as an individual-level risk behavior. We introduce a new approach that connects the conditions surrounding the initiation of sex with subsequent relationship well-being, examines relationships as sequences of interdependent events, and indexes relationship experiences to individually held ideals. New card-sort data from southern Malawi capture young women’s relationship experiences and their ideals in a sequential framework. Using optimal matching, we measure the distance between ideal and experienced relationship sequences to (1) assess the associations between ideological congruence and perceived relationship well-being, (2) compare this ideal-based approach to other experience-based alternatives, and (3) identify individual- and couple-level correlates of congruence between ideals and experiences in the romantic realm. We show that congruence between ideals and experiences conveys relationship well-being along four dimensions: expressions of love and support, robust communication habits, perceived biological safety, and perceived relationship stability. We further show that congruence is patterned by socioeconomic status and supported by shared ideals within romantic dyads. We argue that conceiving of ideals as anchors for how sexual experiences are manifest advances current understandings of romantic relationships, and we suggest that this approach has applications for other domains of life. PMID:27110031

  18. Ideals and Category Typicality

    ERIC Educational Resources Information Center

    Kim, ShinWoo; Murphy, Gregory L.

    2011-01-01

    Barsalou (1985) argued that exemplars that serve category goals become more typical category members. Although this claim has received support, we investigated (a) whether categories have a single ideal, as negatively valenced categories (e.g., cigarette) often have conflicting goals, and (b) whether ideal items are in fact typical, as they often…

  19. Ideal AFROC and FROC observers.

    PubMed

    Khurd, Parmeshwar; Liu, Bin; Gindi, Gene

    2010-02-01

    Detection of multiple lesions in images is a medically important task and free-response receiver operating characteristic (FROC) analyses and its variants, such as alternative FROC (AFROC) analyses, are commonly used to quantify performance in such tasks. However, ideal observers that optimize FROC or AFROC performance metrics have not yet been formulated in the general case. If available, such ideal observers may turn out to be valuable for imaging system optimization and in the design of computer aided diagnosis techniques for lesion detection in medical images. In this paper, we derive ideal AFROC and FROC observers. They are ideal in that they maximize, amongst all decision strategies, the area, or any partial area, under the associated AFROC or FROC curve. Calculation of observer performance for these ideal observers is computationally quite complex. We can reduce this complexity by considering forms of these observers that use false positive reports derived from signal-absent images only. We also consider a Bayes risk analysis for the multiple-signal detection task with an appropriate definition of costs. A general decision strategy that minimizes Bayes risk is derived. With particular cost constraints, this general decision strategy reduces to the decision strategy associated with the ideal AFROC or FROC observer.

  20. 125Te NMR and Seebeck Effect in Bi 2Te 3 Synthesized from Stoichiometric and Te-Rich Melts

    DOE PAGES

    Levin, E. M.; Iowa State Univ., Ames, IA; Riedemann, T. M.; ...

    2016-10-14

    Bi 2Te 3 is a well-known thermoelectric material and, as a new form of quantum matter, a topological insulator. Variation of local chemical composition in Bi2Te3 results in formation of several types of atomic defects, including Bi and Te vacancies and Bi and Te antisite defects; these defects can strongly affect material functionality via generation of free electrons and/or holes. Nonuniform distribution of atomic defects produces electronic inhomogeneity, which can be detected by 125Te nuclear magnetic resonance (NMR). Here we report on 125Te NMR and Seebeck effect (heat to electrical energy conversion) for two single crystalline samples: (#1) grown frommore » stoichiometric composition by Bridgman technique and (#2) grown out of Te-rich, high temperature flux. The Seebeck coefficients of these samples show p- and n-type conductivity, respectively, arising from different atomic defects. 125Te NMR spectra and spin–lattice relaxation measurements demonstrate that both Bi 2Te 3 samples are electronically inhomogeneous at the atomic scale, which can be attributed to a different Te environment due to spatial variation of the Bi/Te ratio and formation of atomic defects. In conclusion, correlations between 125Te NMR spectra, spin–lattice relaxation times, the Seebeck coefficients, carrier concentrations, and atomic defects are discussed. Our data demonstrate that 125Te NMR is an effective probe to study antisite defects in Bi 2Te 3.« less

  1. 125Te NMR and Seebeck Effect in Bi 2Te 3 Synthesized from Stoichiometric and Te-Rich Melts

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Levin, E. M.; Iowa State Univ., Ames, IA; Riedemann, T. M.

    Bi 2Te 3 is a well-known thermoelectric material and, as a new form of quantum matter, a topological insulator. Variation of local chemical composition in Bi2Te3 results in formation of several types of atomic defects, including Bi and Te vacancies and Bi and Te antisite defects; these defects can strongly affect material functionality via generation of free electrons and/or holes. Nonuniform distribution of atomic defects produces electronic inhomogeneity, which can be detected by 125Te nuclear magnetic resonance (NMR). Here we report on 125Te NMR and Seebeck effect (heat to electrical energy conversion) for two single crystalline samples: (#1) grown frommore » stoichiometric composition by Bridgman technique and (#2) grown out of Te-rich, high temperature flux. The Seebeck coefficients of these samples show p- and n-type conductivity, respectively, arising from different atomic defects. 125Te NMR spectra and spin–lattice relaxation measurements demonstrate that both Bi 2Te 3 samples are electronically inhomogeneous at the atomic scale, which can be attributed to a different Te environment due to spatial variation of the Bi/Te ratio and formation of atomic defects. In conclusion, correlations between 125Te NMR spectra, spin–lattice relaxation times, the Seebeck coefficients, carrier concentrations, and atomic defects are discussed. Our data demonstrate that 125Te NMR is an effective probe to study antisite defects in Bi 2Te 3.« less

  2. Simple equations to simulate closed-loop recycling liquid-liquid chromatography: Ideal and non-ideal recycling models.

    PubMed

    Kostanyan, Artak E

    2015-12-04

    The ideal (the column outlet is directly connected to the column inlet) and non-ideal (includes the effects of extra-column dispersion) recycling equilibrium-cell models are used to simulate closed-loop recycling counter-current chromatography (CLR CCC). Simple chromatogram equations for the individual cycles and equations describing the transport and broadening of single peaks and complex chromatograms inside the recycling closed-loop column for ideal and non-ideal recycling models are presented. The extra-column dispersion is included in the theoretical analysis, by replacing the recycling system (connecting lines, pump and valving) by a cascade of Nec perfectly mixed cells. To evaluate extra-column contribution to band broadening, two limiting regimes of recycling are analyzed: plug-flow, Nec→∞, and maximum extra-column dispersion, Nec=1. Comparative analysis of ideal and non-ideal models has shown that when the volume of the recycling system is less than one percent of the column volume, the influence of the extra-column processes on the CLR CCC separation may be neglected. Copyright © 2015 Elsevier B.V. All rights reserved.

  3. Prediction of Combustion Gas Deposit Compositions

    NASA Technical Reports Server (NTRS)

    Kohl, F. J.; Mcbride, B. J.; Zeleznik, F. J.; Gordon, S.

    1985-01-01

    Demonstrated procedure used to predict accurately chemical compositions of complicated deposit mixtures. NASA Lewis Research Center's Computer Program for Calculation of Complex Chemical Equilibrium Compositions (CEC) used in conjunction with Computer Program for Calculation of Ideal Gas Thermodynamic Data (PAC) and resulting Thermodynamic Data Base (THDATA) to predict deposit compositions from metal or mineral-seeded combustion processes.

  4. Nanostructured Metal Oxides for Stoichiometric Degradation of Chemical Warfare Agents.

    PubMed

    Štengl, Václav; Henych, Jiří; Janoš, Pavel; Skoumal, Miroslav

    2016-01-01

    Metal oxides have very important applications in many areas of chemistry, physics and materials science; their properties are dependent on the method of preparation, the morphology and texture. Nanostructured metal oxides can exhibit unique characteristics unlike those of the bulk form depending on their morphology, with a high density of edges, corners and defect surfaces. In recent years, methods have been developed for the preparation of metal oxide powders with tunable control of the primary particle size as well as of a secondary particle size: the size of agglomerates of crystallites. One of the many ways to take advantage of unique properties of nanostructured oxide materials is stoichiometric degradation of chemical warfare agents (CWAs) and volatile organic compounds (VOC) pollutants on their surfaces.

  5. The stoichiometric dissociation constants of carbonic acid in seawater brines from 298 to 267 K

    NASA Astrophysics Data System (ADS)

    Papadimitriou, Stathys; Loucaides, Socratis; Rérolle, Victoire M. C.; Kennedy, Paul; Achterberg, Eric P.; Dickson, Andrew G.; Mowlem, Matthew; Kennedy, Hilary

    2018-01-01

    The stoichiometric dissociation constants of carbonic acid (K1C∗ and K2C∗) were determined by measurement of all four measurable parameters of the carbonate system (total alkalinity, total dissolved inorganic carbon, pH on the total proton scale, and CO2 fugacity) in natural seawater and seawater-derived brines, with a major ion composition equivalent to that of Reference Seawater, to practical salinity (SP) 100 and from 25 °C to the freezing point of these solutions and -6 °C temperature minimum. These values, reported in the total proton scale, provide the first such determinations at below-zero temperatures and for SP > 50. The temperature (T, in Kelvin) and SP dependence of the current pK1C∗ and pK2C∗ (as negative common logarithms) within the salinity and temperature ranges of this study (33 ≤ SP ≤ 100, -6 °C ≤ t ≤ 25 °C) is described by the following best-fit equations: pK1C∗ = -176.48 + 6.14528 SP0.5 - 0.127714 SP + 7.396 × 10-5SP2 + (9914.37 - 622.886 SP0.5 + 29.714 SP) T-1 + (26.05129 - 0.666812 SP0.5) lnT (σ = 0.011, n = 62), and pK2C∗ = -323.52692 + 27.557655 SP0.5 + 0.154922 SP - 2.48396 × 10-4 SP2 + (14763.287 - 1014.819 SP0.5 - 14.35223 SP) T-1 + (50.385807 - 4.4630415 SP0.5) lnT (σ = 0.020, n = 62). These functions are suitable for application to investigations of the carbonate system of internal sea ice brines with a conservative major ion composition relative to that of Reference Seawater and within the temperature and salinity ranges of this study.

  6. Ecological stoichiometry of the honeybee: Pollen diversity and adequate species composition are needed to mitigate limitations imposed on the growth and development of bees by pollen quality.

    PubMed

    Filipiak, Michał; Kuszewska, Karolina; Asselman, Michel; Denisow, Bożena; Stawiarz, Ernest; Woyciechowski, Michał; Weiner, January

    2017-01-01

    The least understood aspects of the nutritional needs of bees are the elemental composition of pollen and the bees' need for a stoichiometrically balanced diet containing the required proportions of nutrients. Reduced plant diversity has been proposed as an indirect factor responsible for the pollinator crisis. We suggest stoichiometric mismatch resulting from a nutritionally unbalanced diet as a potential direct factor. The concentrations and stoichiometric ratios of C, N, S, P, K, Na, Ca, Mg, Fe, Zn, Mn, and Cu were studied in the bodies of honeybees of various castes and sexes and in the nectar and pollen of various plant species. A literature review of the elemental composition of pollen was performed. We identified possible co-limitations of bee growth and development resulting mainly from the scarcity of Na, S, Cu, P and K, and possibly Zn and N, in pollen. Particular castes and sexes face specific limitations. Concentrations of potentially limiting elements in pollen revealed high taxonomic diversity. High floral diversity may be necessary to maintain populations of pollen eaters. Single-species crop plantations, even if these species are rich in nectar and pollen, might limit bee growth and development, not allowing for gathering nutrients in adequate proportions. However, particular plant species may play greater roles than others in balancing honeybee diets. Therefore, we suggest specific plant species that may (1) ensure optimal growth and production of individuals by producing pollen that is exceptionally well balanced stoichiometrically (e.g., clover) or (2) prevent growth and development of honeybees by producing pollen that is extremely unbalanced for bees (e.g., sunflower). Since pollen is generally poor in Na, this element must be supplemented using "dirty water". Nectar cannot supplement the diet with limiting elements. Stoichiometric mismatch should be considered in intervention strategies aimed at improving the nutritional base for bees.

  7. Ecological stoichiometry of the honeybee: Pollen diversity and adequate species composition are needed to mitigate limitations imposed on the growth and development of bees by pollen quality

    PubMed Central

    Kuszewska, Karolina; Asselman, Michel; Denisow, Bożena; Stawiarz, Ernest; Woyciechowski, Michał; Weiner, January

    2017-01-01

    The least understood aspects of the nutritional needs of bees are the elemental composition of pollen and the bees’ need for a stoichiometrically balanced diet containing the required proportions of nutrients. Reduced plant diversity has been proposed as an indirect factor responsible for the pollinator crisis. We suggest stoichiometric mismatch resulting from a nutritionally unbalanced diet as a potential direct factor. The concentrations and stoichiometric ratios of C, N, S, P, K, Na, Ca, Mg, Fe, Zn, Mn, and Cu were studied in the bodies of honeybees of various castes and sexes and in the nectar and pollen of various plant species. A literature review of the elemental composition of pollen was performed. We identified possible co-limitations of bee growth and development resulting mainly from the scarcity of Na, S, Cu, P and K, and possibly Zn and N, in pollen. Particular castes and sexes face specific limitations. Concentrations of potentially limiting elements in pollen revealed high taxonomic diversity. High floral diversity may be necessary to maintain populations of pollen eaters. Single-species crop plantations, even if these species are rich in nectar and pollen, might limit bee growth and development, not allowing for gathering nutrients in adequate proportions. However, particular plant species may play greater roles than others in balancing honeybee diets. Therefore, we suggest specific plant species that may (1) ensure optimal growth and production of individuals by producing pollen that is exceptionally well balanced stoichiometrically (e.g., clover) or (2) prevent growth and development of honeybees by producing pollen that is extremely unbalanced for bees (e.g., sunflower). Since pollen is generally poor in Na, this element must be supplemented using “dirty water”. Nectar cannot supplement the diet with limiting elements. Stoichiometric mismatch should be considered in intervention strategies aimed at improving the nutritional base for bees

  8. Comparison of non-ideal solution theories for multi-solute solutions in cryobiology and tabulation of required coefficients.

    PubMed

    Zielinski, Michal W; McGann, Locksley E; Nychka, John A; Elliott, Janet A W

    2014-10-01

    Thermodynamic solution theories allow the prediction of chemical potentials in solutions of known composition. In cryobiology, such models are a critical component of many mathematical models that are used to simulate the biophysical processes occurring in cells and tissues during cryopreservation. A number of solution theories, both thermodynamically ideal and non-ideal, have been proposed for use with cryobiological solutions. In this work, we have evaluated two non-ideal solution theories for predicting water chemical potential (i.e. osmolality) in multi-solute solutions relevant to cryobiology: the Elliott et al. form of the multi-solute osmotic virial equation, and the Kleinhans and Mazur freezing point summation model. These two solution theories require fitting to only single-solute data, although they can make predictions in multi-solute solutions. The predictions of these non-ideal solution theories were compared to predictions made using ideal dilute assumptions and to available literature multi-solute experimental osmometric data. A single, consistent set of literature single-solute solution data was used to fit for the required solute-specific coefficients for each of the non-ideal models. Our results indicate that the two non-ideal solution theories have similar overall performance, and both give more accurate predictions than ideal models. These results can be used to select between the non-ideal models for a specific multi-solute solution, and the updated coefficients provided in this work can be used to make the desired predictions. Copyright © 2014 The Authors. Published by Elsevier Inc. All rights reserved.

  9. Curie temperature, exchange integrals, and magneto-optical properties in off-stoichiometric bismuth iron garnet epitaxial films

    NASA Astrophysics Data System (ADS)

    Vertruyen, B.; Cloots, R.; Abell, J. S.; Jackson, T. J.; da Silva, R. C.; Popova, E.; Keller, N.

    2008-09-01

    We have studied the influence of the stoichiometry on the structural, magnetic, and magneto-optical properties of bismuth iron garnet (Bi3Fe5O12) thin films grown by pulsed laser deposition. Films with different stoichiometries have been obtained by varying the Bi/Fe ratio of the target and the oxygen pressure during deposition. Stoichiometry variations influence the Curie temperature TC by tuning the (Fe)-O-[Fe] geometry: TC increases when the lattice parameter decreases, contrary to what happens in the case of stoichiometric rare-earth iron garnets. The thermal variation of the magnetization, the Faraday rotation, and the Faraday ellipticity have been analyzed in the frame of the Néel two-sublattice magnetization model giving energies of -48K (4.1 meV), -29K (2.5 meV), and 84 K (7.3 meV) for the three magnetic exchange integrals jaa , jdd , and jad , respectively. Magneto-optical spectroscopy linked to compositional analysis by Rutherford backscattering spectroscopy shows that Bi and/or Fe deficiencies also affect the spectral variation (between 1.77 and 3.1 eV). Our results suggest that bismuth deficiency has an effect on the magneto-optical response of the tetrahedral Fe sublattice, whereas small iron deficiencies affect predominantly the magneto-optical response of the octahedral sublattice.

  10. Optimizing Thermoelectric Properties of In Situ Plasma-Spray-Synthesized Sub-stoichiometric TiO2-x Deposits

    NASA Astrophysics Data System (ADS)

    Lee, Hwasoo; Seshadri, Ramachandran Chidambaram; Pala, Zdenek; Sampath, Sanjay

    2018-06-01

    In this article, an attempt has been made to relate the thermoelectric properties of thermal spray deposits of sub-stoichiometric titania to process-induced phase and microstructural variances. The TiO2-x deposits were formed through the in situ reaction of the TiO1.9 or TiO1.7 feedstock within the high-temperature plasma flame and manipulated via varying the amounts of hydrogen fed into in the thermal plasma. Changes in the flow rates of H2 in the plasma plume greatly affected the in-flight particle behavior and composition of the deposits. For reference, a high-velocity oxy-fuel spray torch was also used to deposit the two varieties of feedstocks. Refinements to the representation of the in-flight particle characteristics derived via single particle and ensemble diagnostic methods are proposed using the group parameters (melting index and kinetic energy). The results show that depending on the value of the melting index, there is an inverse proportional relationship between electrical conductivity and Seebeck coefficient, whereas thermal conductivity has a directly proportional relationship with the electrical conductivity. Retention of the original phase and reduced decomposition is beneficial to retain the high Seebeck coefficient or the high electrical conductivity in the TiO2 system.

  11. Pulsed laser deposition of chalcogenide sulfides from multi- and single-component targets: the non-stoichiometric material transfer

    NASA Astrophysics Data System (ADS)

    Schou, Jørgen; Gansukh, Mungunshagai; Ettlinger, Rebecca B.; Cazzaniga, Andrea; Grossberg, Maarja; Kauk-Kuusik, Marit; Canulescu, Stela

    2018-01-01

    The mass transfer from target to films is incongruent for chalcogenide sulfides in contrast to the expectations of pulsed laser deposition (PLD) as a stoichiometric film growth process. Films produced from a CZTS (Cu2ZnSnS4) multi-component target have no Cu below a fluence threshold of 0.2 J/cm2, and the Cu content is also very low at low fluence from a single-component target. Above this threshold, the Cu content in the films increases almost linearly up to a value above the stoichiometric value, while the ratio of the concentration of the other metals Zn to Sn (Zn/Sn) remains constant. Films of a similar material CTS (Cu2SnS3) have been produced by PLD from a CTS target and exhibits a similar trend in the same fluence region. The results are discussed on the basis of solid-state data and the existing data from the literature.

  12. Soil C and N availability determine the priming effect: microbial N mining and stoichiometric decomposition theories

    NASA Astrophysics Data System (ADS)

    Chen, Ruirui; Senbayram, Mehmet; Blagodatsky, Sergey; Dittert, Klaus; Lin, Xiangui; Blagodatskaya, Evgenia; Kuzyakov, Yakov

    2014-05-01

    The increasing input of anthropogenically derived nitrogen (N) to ecosystems raises a crucial question: how does available N modify the decomposer community and thus affects the mineralization of soil organic matter (SOM). Moreover, N input modifies the priming effect (PE), that is, the effect of fresh organics on the microbial decomposition of SOM. We studied the interactive effects of C and N on SOM mineralization (by natural 13C labelling adding C4-sucrose or C4-maize straw to C3-soil) in relation to microbial growth kinetics and to the activities of five hydrolytic enzymes. This encompasses the groups of parameters governing two mechanisms of priming effects - microbial N mining and stoichiometric decomposition theories. In sole C treatments, positive PE was accompanied by a decrease in specific microbial growth rates, confirming a greater contribution of K-strategists to the decomposition of native SOM. Sucrose addition with N significantly accelerated mineralization of native SOM, whereas mineral N added with plant residues accelerated decomposition of plant residues. This supports the microbial mining theory in terms of N limitation. Sucrose addition with N was accompanied by accelerated microbial growth, increased activities of β-glucosidase and cellobiohydrolase, and decreased activities of xylanase and leucine amino peptidase. This indicated an increased contribution of r-strategists to the PE and to decomposition of cellulose but the decreased hemicellulolytic and proteolytic activities. Thus, the acceleration of the C cycle was primed by exogenous organic C and was controlled by N. This confirms the stoichiometric decomposition theory. Both K- and r-strategists were beneficial for priming effects, with an increasing contribution of K-selected species under N limitation. Thus, the priming phenomenon described in 'microbial N mining' theory can be ascribed to K-strategists. In contrast, 'stoichiometric decomposition' theory, that is, accelerated OM

  13. Vesicular delivery of crystalline calcium minerals to ECM in biomineralized nanoclay composites

    NASA Astrophysics Data System (ADS)

    Katti, Kalpana S.; Ambre, Avinash H.; Payne, Scott; Katti, Dinesh R.

    2015-04-01

    The mechanisms of mineralization and new bone formation were explored in newly formed extracellular matrix in a nanoclay based composite. Nanoclay films were prepared by intercalating the clays with amino acids and using the amino acids for mineralization of hydroxyapatite. The biomineralized hydroxyapatite (HAP) inside nanoclay galleries or in situ HAP/clay was further used to make films (substrates) using polycaprolactone (PCL) that were seeded with mesenchymal stem cells in a two-stage seeding process. SEM imaging experiments performed on PCL/in situ HAPclay composite films seeded with human MSCs indicated formation of matrix vesicles. The vesicles appear to emerge from the cells that are adhered to the nanoclay HAP films and also deposited in the extracellular space. Vesicles are also observed to be embedded in the cells or under the surface of cells. Crystalline structures with Ca and P were found inside vesicles. The Ca/P ratios obtained using energy dispersive spectroscopy indicate values ranging from below 0.7 to the stoichiometric HAP value of 1.67. The Ca/P ratios were obtained to be closer to the stoichiometric value for single seeding experiments as compared to the double seeding experiments indicating more new bone formation in double seeding experiments. New bone formation with bone mimetic mineralization is thus observed on the in situ HAP nanoclay PCL samples. Hence the PCL/in situ HAPclay composites besides being osteoinductive are also capable of providing a favorable micro-environment for cell dependent processes involved in bone mineral formation.

  14. Intense Photosensitized Emission from Stoichiometric Compounds Featuring Mn(2+) in Seven- and Eightfold Coordination Environments.

    PubMed

    Reid, Howard O. N.; Kahwa, Ishenkumba A.; White, Andrew J. P.; Williams, David J.

    1998-07-27

    Synthetic, structural and luminescence studies of stoichiometric crown ether compounds of Mn(2+) in well-defined coordination environments were undertaken in an effort to understand the origin of emitting crystal defects found in cubic F23 [(K18C6)(4)MnBr(4)][TlBr(4)](2) crystals (Fender, N. S.; et al. Inorg. Chem. 1997, 36, 5539). The new compound [Mn(12C4)(2)][MnBr(4)](2)[N(CH(3))(4)](2) (3) features Mn(2+) ions in eight- and fourfold coordination environments of [Mn(12C4)(2)](2+) and MnBr(4)(2)(-) respectively, while Mn(2+) in [Mn(15C5)(H(2)O)(2)][TlBr(5)] (4) is in the sevenfold coordination polyhedron of [Mn(15C5)(H(2)O)(2)](2+). Crystal data for 3: monoclinic, P2(1)/c (No. 14); a = 14.131(3) Å, b = 12.158(1) Å, c = 14.239(2) Å, beta = 110.37(1) degrees, Z = 2, R1 = 0.039 and wR2 = 0.083. For 3, long-lived emission (77 K decay rate approximately 3 x 10 s(-)(1)) from [Mn(12C4)(2)](2+) (the first for eight-coordinate Mn(2+) in stoichiometric compounds) is observed (lambda(max) approximately 546 nm) along with that of the sensitizing MnBr(4)(2)(-) (lambda(max) approximately 513 nm), which is partially quenched. Emission from the seven-coordinate [Mn(15C5)(H(2)O)(2)](2+) species of 4 and [Mn(15C5)(H(2)O)(2)][MnBr(4)] (the first for seven-coordinate Mn(2+) in stoichiometric compounds) peaks at lambda(max) approximately 592 nm. Unusually intense absorptions attributable to the seven-coordinate species are observed at 317 ((2)T(2)((2)I) <-- (6)A(1)), 342 ((4)T(1)((4)P) <-- (6)A(1)), 406 ((4)E((4)G) <-- (6)A(1)), and 531 ((4)T(1)((4)G) <-- (6)A(1)) nm.

  15. Stoichiometric sensing to opt between gelation and crystallization.

    PubMed

    Vidyasagar, Adiyala; Sureshan, Kana M

    2015-10-05

    A new class of organogelators having a cyclohexane-1a,3a-diol motif capable of congealing non-polar liquids was developed. These gelators underwent crystallization at low concentration and gelation above the critical gelation concentration (CGC) in the same solvent. The crystals and gel fibers were analyzed by single crystal XRD and PXRD respectively, which revealed their different modes of assembly. The XRD studies and thermogravimetric analysis (TGA) confirmed that the crystals contain a water of crystallization whereas the gel fibers do not. A systematic study revealed that when the concentration of the gelator exceeds that of adventitious water in the solvent, it congeals the solvent and when the concentration of the gelator is less than water, it undergoes crystallization. This unprecedented stoichiometric sensing behavior in deciding the mode of self-assembly offers a handle to opt between mutually competing gelation and crystallization. We have confirmed that the system can be biased to congeal or crystallize by varying the amount of water. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Stoichiometric Mismatch between Consumers and Resources Mediates the Growth of Rocky Intertidal Suspension Feeders

    PubMed Central

    Bracken, Matthew E. S.

    2017-01-01

    The concept of ecological stoichiometry—the balancing of elemental ratios in ecological interactions—has transformed our thinking about processes in natural systems. Here, this perspective is applied to rocky shore ecosystems to explore the consequences of variation in internal nutrient ratios across two trophic levels. Specifically, I measured the internal concentrations of carbon (C) and nitrogen (N) in mussels (Mytilus spp.) and particulate organic matter (POM) to evaluate the effects of stoichiometric mismatch—the difference in the carbon-to-nitrogen ratio (C:N) between a consumer and its resources—on mussel growth at sites on the coasts of Oregon, USA, and the South Island of New Zealand. As POM quality (i.e., Chl a, a proxy for phytoplankton availability in the POM) increased, C:N of the POM declined, but C:N of mussels increased. This resulted in a greater mismatch in C:N between mussels and their food source at low Chl a. Mussel growth across sites was positively associated with Chl a, particulate organic carbon (POC), and particulate organic nitrogen (PON) but negatively associated with stoichiometric mismatch. Overall, as the elemental ratios of consumers became more different from those of their resources, growth declined, likely due to the energetic cost associated with processing lower quality food. Furthermore, the effect of food quantity on growth depended on stoichiometric mismatch. In New Zealand, where mismatch was high—i.e., consumer C:N differed substantially from resource C:N—consumer growth was strongly affected by resource quantity (Chl a or POC). However, in Oregon, where mismatch was low, the relationship between resource quantity and growth was considerably weaker. This interaction between resource quantity and mismatch was not apparent for PON, which is consistent with variation in PON underlying variation in POM C:N and highlights the role of N in limiting growth. Previous research has neglected the importance of ecological

  17. Charge ordering in stoichiometric FeTe: Scanning tunneling microscopy and spectroscopy

    DOE PAGES

    Li, Wei; Yin, Wei -Guo; Wang, Lili; ...

    2016-01-04

    In this study, we use scanning tunneling microscopy and spectroscopy to reveal a unique stripy charge order in a parent phase of iron-based superconductors in stoichiometric FeTe epitaxy films. The charge order has unusually the same—usually half—period as the spin order. We also found highly anisotropic electron band dispersions being large and little along the ferromagnetic (crystallographic b) and antiferromagnetic (a) directions, respectively. Our data suggest that the microscopic mechanism is likely of the Stoner type driven by interatomic Coulomb repulsion V ij, and that V ij and charge fluctuations, so far much neglected, are important to the understanding ofmore » iron-based superconductors.« less

  18. Limitation of egg production in Calanus finmarchicus in the field: A stoichiometric analysis

    NASA Astrophysics Data System (ADS)

    Mayor, Daniel J.; Anderson, Thomas R.; Pond, David W.; Irigoien, Xabier

    2009-11-01

    The egg production of marine copepods correlates with a range of variables, including the availability of organic carbon (C), nitrogen (N) and the polyunsaturated fatty acids (PUFAs) 20:5( n-3) (EPA) and 22:6( n-3) (DHA). However, an understanding of which substrates limit egg production in the natural environment has yet to be reached. The quantities of C, N, EPA and DHA ingested, derived from parental biomass, and invested in eggs by female Calanus finmarchicus during a 5-day incubation experiment were examined using stoichiometric theory to determine which substrate was limiting. The majority of each substrate was derived from parental biomass, and therefore the existing stoichiometric theory is developed to include this route of supply. The females were essentially devoid of lipid reserves, as evidenced by the lack of the storage fatty acids 20:1( n-9) and 22:1( n-11), and carbon limitation was predicted under most of the scenarios examined. Nitrogen limitation was only apparent when carbon and nitrogen utilisation efficiencies were assumed to be high (0.5) and low (0.4) respectively. PUFAs were assumed to be utilised with high efficiency (0.9), and were never predicted to limit production. This work highlights the need for a more detailed understanding of the maintenance requirements that marine copepods have for C, N, EPA, and DHA and hence the efficiencies with these substrates can be utilised for growth.

  19. Kirkwood–Buff integrals for ideal solutions

    PubMed Central

    Ploetz, Elizabeth A.; Bentenitis, Nikolaos; Smith, Paul E.

    2010-01-01

    The Kirkwood–Buff (KB) theory of solutions is a rigorous theory of solution mixtures which relates the molecular distributions between the solution components to the thermodynamic properties of the mixture. Ideal solutions represent a useful reference for understanding the properties of real solutions. Here, we derive expressions for the KB integrals, the central components of KB theory, in ideal solutions of any number of components corresponding to the three main concentration scales. The results are illustrated by use of molecular dynamics simulations for two binary solutions mixtures, benzene with toluene, and methanethiol with dimethylsulfide, which closely approach ideal behavior, and a binary mixture of benzene and methanol which is nonideal. Simulations of a quaternary mixture containing benzene, toluene, methanethiol, and dimethylsulfide suggest this system displays ideal behavior and that ideal behavior is not limited to mixtures containing a small number of components. PMID:20441282

  20. Ideal regularization for learning kernels from labels.

    PubMed

    Pan, Binbin; Lai, Jianhuang; Shen, Lixin

    2014-08-01

    In this paper, we propose a new form of regularization that is able to utilize the label information of a data set for learning kernels. The proposed regularization, referred to as ideal regularization, is a linear function of the kernel matrix to be learned. The ideal regularization allows us to develop efficient algorithms to exploit labels. Three applications of the ideal regularization are considered. Firstly, we use the ideal regularization to incorporate the labels into a standard kernel, making the resulting kernel more appropriate for learning tasks. Next, we employ the ideal regularization to learn a data-dependent kernel matrix from an initial kernel matrix (which contains prior similarity information, geometric structures, and labels of the data). Finally, we incorporate the ideal regularization to some state-of-the-art kernel learning problems. With this regularization, these learning problems can be formulated as simpler ones which permit more efficient solvers. Empirical results show that the ideal regularization exploits the labels effectively and efficiently. Copyright © 2014 Elsevier Ltd. All rights reserved.

  1. The Acid-Base Properties and Chemical Composition of the Surface of the InSb-ZnTe System

    NASA Astrophysics Data System (ADS)

    Kirovskaya, I. A.; Shubenkova, E. G.; Timoshenko, O. T.; Filatova, T. N.

    2008-04-01

    The acid-base properties and chemical composition of the surface of solid solutions and binary components of the InSb-ZnTe system were studied by the hydrolytic adsorption, nonaqueous conductometric titration, mechanochemistry, IR spectroscopy, and mass spectrometry methods. The strength, nature, and concentration of acid centers were determined. Changes in the concentration of acid centers caused by surface exposure to CO and changes in the composition of the system were also studied. The mechanism of acid-base interactions was established. The chemical composition of the surface of system components exposed to air included adsorbed H2O molecules, OH- groups, hydrocarbon and oxocarbon compounds, and the products of surface atom oxidation. After thermal treatment in a vacuum, the composition of the surface approached the stoichiometric composition.

  2. Intuitionistic fuzzy n-fold KU-ideal of KU-algebra

    NASA Astrophysics Data System (ADS)

    Mostafa, Samy M.; Kareem, Fatema F.

    2018-05-01

    In this paper, we apply the notion of intuitionistic fuzzy n-fold KU-ideal of KU-algebra. Some types of ideals such as intuitionistic fuzzy KU-ideal, intuitionistic fuzzy closed ideal and intuitionistic fuzzy n-fold KU-ideal are studied. Also, the relations between intuitionistic fuzzy n-fold KU-ideal and intuitionistic fuzzy KU-ideal are discussed. Furthermore, a few results of intuitionistic fuzzy n-fold KU-ideals of a KU-algebra under homomorphism are discussed.

  3. Examples for Non-Ideal Solution Thermodynamics Study

    ERIC Educational Resources Information Center

    David, Carl W.

    2004-01-01

    A mathematical model of a non-ideal solution is presented, where it is shown how and where the non-ideality manifests itself in the standard thermodynamics tableau. Examples related to the non-ideal solution thermodynamics study are also included.

  4. Ideal Magnetic Dipole Scattering

    NASA Astrophysics Data System (ADS)

    Feng, Tianhua; Xu, Yi; Zhang, Wei; Miroshnichenko, Andrey E.

    2017-04-01

    We introduce the concept of tunable ideal magnetic dipole scattering, where a nonmagnetic nanoparticle scatters light as a pure magnetic dipole. High refractive index subwavelength nanoparticles usually support both electric and magnetic dipole responses. Thus, to achieve ideal magnetic dipole scattering one has to suppress the electric dipole response. Such a possibility was recently demonstrated for the so-called anapole mode, which is associated with zero electric dipole scattering. By spectrally overlapping the magnetic dipole resonance with the anapole mode, we achieve ideal magnetic dipole scattering in the far field with tunable strong scattering resonances in the near infrared spectrum. We demonstrate that such a condition can be realized at least for two subwavelength geometries. One of them is a core-shell nanosphere consisting of a Au core and silicon shell. It can be also achieved in other geometries, including nanodisks, which are compatible with current nanofabrication technology.

  5. Thermal-induced domain wall motion of tip-inverted micro/nanodomains in near-stoichiometric LiNbO3 crystals

    NASA Astrophysics Data System (ADS)

    Liu, X. Y.; Kitamura, K.; Liu, Y. M.; Ohuchi, F. S.; Li, J. Y.

    2011-09-01

    Thermal-induced domain wall motion of tip-inverted micro/nanodomains in near-stoichiometric LiNbO3 single crystals was investigated using piezoresponse force microscopy (PFM). The domain wall motion was observed in PFM phase and amplitude images at room temperature after the sample was subjected to a thermal process at a heating temperature higher than 100 °C. In hexagonal domains with only y walls, predetermined nucleation with layer-by-layer growth is the main mechanism for the domain wall motion. In the domains composed of both x walls and y walls, the x walls are more mobile than the y walls, and the domain wall motion starts from the random nucleation of steps along the x walls that finally grow into y walls. The domain wall motion in the near-stoichiometric LiNbO3 crystal is attributed to the energy-preferable domain wall orientation, the pyroelectric effect, and the screening charge variation caused by the thermal process.

  6. Association between different phases of menstrual cycle and body image measures of perceived size, ideal size, and body dissatisfaction.

    PubMed

    Teixeira, André Luiz S; Dias, Marcelo Ricardo C; Damasceno, Vinícius O; Lamounier, Joel A; Gardner, Rick M

    2013-12-01

    The association between phases of the menstrual cycle and body image was investigated. 44 university women (M age = 23.3 yr., SD = 4.7) judged their perceived and ideal body size, and body dissatisfaction was calculated at each phase of the menstrual cycle, including premenstrual, menstrual, and intermenstrual. Participants selected one of nine figural drawings ranging from very thin to obese that represented their perceived size and ideal size. Body dissatisfaction was measured as the absolute difference between scores on perceived and ideal figural drawings. During each menstrual phase, anthropometric measures of weight, height, body mass index, circumference of waist and abdomen, and body composition were taken. There were no significant differences in any anthropometric measures between the three menstrual cycle phases. Perceived body size and body dissatisfaction were significantly different between menstrual phases, with the largest perceived body size and highest body dissatisfaction occurring during the menstrual phase. Ideal body size did not differ between menstrual phases, although participants desired a significantly smaller ideal size as compared to the perceived size.

  7. The moderating effect of gender on ideal-weight goals and exercise dependence symptoms.

    PubMed

    Cook, Brian; Hausenblas, Heather; Rossi, James

    2013-03-01

    Background and aims Exercise dependence is implicated in the development of eating disorders and muscle dysmorphic disorder. Although conceptually these disorders represent similar pathologies they largely affect different genders and result in opposite body composition, appearance, and ideal-weight goals (i.e., to gain or lose/maintain weight). Therefore, understanding individuals' ideal-weight goals related to engaging in exercise while simultaneously examining gender differences in exercise dependence symptoms may help to identify those whom may be most at-risk for eating disorders and muscle dysmorphic disorder. The purpose of our study was to examine the moderating effect of gender for exercise dependence symptoms in relation to weight gain, loss, or maintenance goals. Methods Self-reported exercise behavior and exercise dependence symptoms (i.e., Exercise Dependence Scale) were assessed in 513 undergraduate students. Results Our analysis revealed a moderating effect for gender on ideal-weight goals and a gender difference in exercise dependence symptoms. Specifically, men who were dissatisfied with their current weight reported more exercise dependence symptoms than women. Conclusions These results support a growing body of research and extend our understanding of the relationships among exercise dependence and gender specific body-focused psychiatric disorders.

  8. Improved Classification of Mammograms Following Idealized Training

    PubMed Central

    Hornsby, Adam N.; Love, Bradley C.

    2014-01-01

    People often make decisions by stochastically retrieving a small set of relevant memories. This limited retrieval implies that human performance can be improved by training on idealized category distributions (Giguère & Love, 2013). Here, we evaluate whether the benefits of idealized training extend to categorization of real-world stimuli, namely classifying mammograms as normal or tumorous. Participants in the idealized condition were trained exclusively on items that, according to a norming study, were relatively unambiguous. Participants in the actual condition were trained on a representative range of items. Despite being exclusively trained on easy items, idealized-condition participants were more accurate than those in the actual condition when tested on a range of item types. However, idealized participants experienced difficulties when test items were very dissimilar from training cases. The benefits of idealization, attributable to reducing noise arising from cognitive limitations in memory retrieval, suggest ways to improve real-world decision making. PMID:24955325

  9. Improved Classification of Mammograms Following Idealized Training.

    PubMed

    Hornsby, Adam N; Love, Bradley C

    2014-06-01

    People often make decisions by stochastically retrieving a small set of relevant memories. This limited retrieval implies that human performance can be improved by training on idealized category distributions (Giguère & Love, 2013). Here, we evaluate whether the benefits of idealized training extend to categorization of real-world stimuli, namely classifying mammograms as normal or tumorous. Participants in the idealized condition were trained exclusively on items that, according to a norming study, were relatively unambiguous. Participants in the actual condition were trained on a representative range of items. Despite being exclusively trained on easy items, idealized-condition participants were more accurate than those in the actual condition when tested on a range of item types. However, idealized participants experienced difficulties when test items were very dissimilar from training cases. The benefits of idealization, attributable to reducing noise arising from cognitive limitations in memory retrieval, suggest ways to improve real-world decision making.

  10. Soil C and N availability determine the priming effect: microbial N mining and stoichiometric decomposition theories.

    PubMed

    Chen, Ruirui; Senbayram, Mehmet; Blagodatsky, Sergey; Myachina, Olga; Dittert, Klaus; Lin, Xiangui; Blagodatskaya, Evgenia; Kuzyakov, Yakov

    2014-07-01

    The increasing input of anthropogenically derived nitrogen (N) to ecosystems raises a crucial question: how does available N modify the decomposer community and thus affects the mineralization of soil organic matter (SOM). Moreover, N input modifies the priming effect (PE), that is, the effect of fresh organics on the microbial decomposition of SOM. We studied the interactive effects of C and N on SOM mineralization (by natural (13) C labelling adding C4 -sucrose or C4 -maize straw to C3 -soil) in relation to microbial growth kinetics and to the activities of five hydrolytic enzymes. This encompasses the groups of parameters governing two mechanisms of priming effects - microbial N mining and stoichiometric decomposition theories. In sole C treatments, positive PE was accompanied by a decrease in specific microbial growth rates, confirming a greater contribution of K-strategists to the decomposition of native SOM. Sucrose addition with N significantly accelerated mineralization of native SOM, whereas mineral N added with plant residues accelerated decomposition of plant residues. This supports the microbial mining theory in terms of N limitation. Sucrose addition with N was accompanied by accelerated microbial growth, increased activities of β-glucosidase and cellobiohydrolase, and decreased activities of xylanase and leucine amino peptidase. This indicated an increased contribution of r-strategists to the PE and to decomposition of cellulose but the decreased hemicellulolytic and proteolytic activities. Thus, the acceleration of the C cycle was primed by exogenous organic C and was controlled by N. This confirms the stoichiometric decomposition theory. Both K- and r-strategists were beneficial for priming effects, with an increasing contribution of K-selected species under N limitation. Thus, the priming phenomenon described in 'microbial N mining' theory can be ascribed to K-strategists. In contrast, 'stoichiometric decomposition' theory, that is, accelerated OM

  11. An ideal free-kick

    NASA Astrophysics Data System (ADS)

    De Luca, R.; Faella, O.

    2017-01-01

    The kinematics of a free-kick is studied. As in projectile motion, the free-kick is ideal since we assume that a point-like ball moves in the absence of air resistance. We have experienced the fortunate conjuncture of a classical mechanics lecture taught right before an important football game. These types of sports events might trigger a great deal of attention from the classroom. The idealized problem is devised in such a way that students are eager to come to the end of the whole story.

  12. On controlling nonlinear dissipation in high order filter methods for ideal and non-ideal MHD

    NASA Technical Reports Server (NTRS)

    Yee, H. C.; Sjogreen, B.

    2004-01-01

    The newly developed adaptive numerical dissipation control in spatially high order filter schemes for the compressible Euler and Navier-Stokes equations has been recently extended to the ideal and non-ideal magnetohydrodynamics (MHD) equations. These filter schemes are applicable to complex unsteady MHD high-speed shock/shear/turbulence problems. They also provide a natural and efficient way for the minimization of Div(B) numerical error. The adaptive numerical dissipation mechanism consists of automatic detection of different flow features as distinct sensors to signal the appropriate type and amount of numerical dissipation/filter where needed and leave the rest of the region free from numerical dissipation contamination. The numerical dissipation considered consists of high order linear dissipation for the suppression of high frequency oscillation and the nonlinear dissipative portion of high-resolution shock-capturing methods for discontinuity capturing. The applicable nonlinear dissipative portion of high-resolution shock-capturing methods is very general. The objective of this paper is to investigate the performance of three commonly used types of nonlinear numerical dissipation for both the ideal and non-ideal MHD.

  13. Stoichiometric control of DNA-grafted colloid self-assembly

    DOE PAGES

    Vo, Thi; Venkatasubramanian, Venkat; Kumar, Sanat; ...

    2015-04-06

    In this study, there has been considerable interest in understanding the self-assembly of DNA-grafted nanoparticles into different crystal structures, e.g., CsCl, AlB₂, and Cr₃Si. Although there are important exceptions, a generally accepted view is that the right stoichiometry of the two building block colloids needs to be mixed to form the desired crystal structure. To incisively probe this issue, we combine experiments and theory on a series of DNA-grafted nanoparticles at varying stoichiometries, including noninteger values. We show that stoichiometry can couple with the geometries of the building blocks to tune the resulting equilibrium crystal morphology. As a concrete example,more » a stoichiometric ratio of 3:1 typically results in the Cr₃Si structure. However, AlB₂ can form when appropriate building blocks are used so that the AlB₂ standard-state free energy is low enough to overcome the entropic preference for Cr₃Si. These situations can also lead to an undesirable phase coexistence between crystal polymorphs. Thus, whereas stoichiometry can be a powerful handle for direct control of lattice formation, care must be taken in its design and selection to avoid polymorph coexistence.« less

  14. Superconductivity in La-deficient and stoichiometric La/sub 2/CuO/sub 4/

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Shaheen, S.A.; Jisrawi, N.; Lee, Y.H.

    The effects of La deficiency and of impurities on the occurrence of filamentary superconductivity in La/sub 2/CuO/sub 4/ have been investigated by magnetic-susceptibility and electrical-resistivity measurements. Reducing the purity of the starting material degrades the superconductivity. La deficiency causes a fully reentrant superconducting-to-normal-state transition with decreasing temperature at temperatures below T/sub c/. This behavior clarifies the incipient reentrance which is observed in nominally stoichiometric La/sub 2/CuO/sub 4/. We associate the reentrant transition with the recently observed structural transformation from the orthorhombic to a semiconducting monoclinic phase.

  15. First Measurements of Time-Dependent Nucleation as a Function of Composition in Na2O.2CaO.3SiO2 Glasses

    NASA Technical Reports Server (NTRS)

    Kelton, K. F.; Narayan, K. Lakshmi

    1996-01-01

    The first measurements in any system of the composition dependence of the time-dependent nucleation rate are presented Nucleation rates of the stoichiometric crystalline phase, Na2O.2CaO.3SiO2, from quenched glasses made with different SiO2 concentrations were determined as a function of temperature and glass composition. A strong compositional dependence of the nucleation rates and a weak dependence for the induction times are observed. Using measured values of the liquidus temperatures and growth velocities as a function of glass composition, these data are shown to be consistent with predictions from the classical theory of nucleation, assuming a composition-dependent interfacial energy.

  16. Recharging Our Sense of Idealism: Concluding Thoughts

    ERIC Educational Resources Information Center

    D'Andrea, Michael; Dollarhide, Colette T.

    2011-01-01

    In this article, the authors aim to recharge one's sense of idealism. They argue that idealism is the Vitamin C that sustains one's commitment to implementing humanistic principles and social justice practices in the work of counselors and educators. The idealism that characterizes counselors and educators who are humanistic and social justice…

  17. Heavy-Duty Stoichiometric Compression Ignition Engine with Improved Fuel Economy over Alternative Technologies for Meeting 2010 On-Highway Emission

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Kirby J. Baumgard; Richard E. Winsor

    2009-12-31

    The objectives of the reported work were: to apply the stoichiometric compression ignition (SCI) concept to a 9.0 liter diesel engine; to obtain engine-out NO{sub x} and PM exhaust emissions so that the engine can meet 2010 on-highway emission standards by applying a three-way catalyst for NO{sub x} control and a particulate filter for PM control; and to simulate an optimize the engine and air system to approach 50% thermal efficiency using variable valve actuation and electric turbo compounding. The work demonstrated that an advanced diesel engine can be operated at stoichiometric conditions with reasonable particulate and NOx emissions atmore » full power and peak torque conditions; calculated that the SCI engine will operate at 42% brake thermal efficiency without advanced hardware, turbocompounding, or waste heat recovery; and determined that EGR is not necessary for this advanced concept engine, and this greatly simplifies the concept.« less

  18. Genetic and environmental influences on thin-ideal internalization.

    PubMed

    Suisman, Jessica L; O'Connor, Shannon M; Sperry, Steffanie; Thompson, J Kevin; Keel, Pamela K; Burt, S Alexandra; Neale, Michael; Boker, Steven; Sisk, Cheryl; Klump, Kelly L

    2012-12-01

    Current research on the etiology of thin-ideal internalization focuses on psychosocial influences (e.g., media exposure). The possibility that genetic influences also account for variance in thin-ideal internalization has never been directly examined. This study used a twin design to estimate genetic effects on thin-ideal internalization and examine if environmental influences are primarily shared or nonshared in origin. Participants were 343 postpubertal female twins (ages: 12-22 years; M = 17.61) from the Michigan State University Twin Registry. Thin-ideal internalization was assessed using the Sociocultural Attitudes toward Appearance Questionnaire-3. Twin modeling suggested significant additive genetic and nonshared environmental influences on thin-ideal internalization. Shared environmental influences were small and non-significant. Although prior research focused on psychosocial factors, genetic influences on thin-ideal internalization were significant and moderate in magnitude. Research is needed to investigate possible interplay between genetic and nonshared environmental factors in the development of thin-ideal internalization. Copyright © 2012 Wiley Periodicals, Inc.

  19. High-temperature deformation of stoichiometric /sup 239/PuO/sub 2/

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Petrovic, J.J.; Land, C.C.

    1980-03-01

    The deformation behavior of stoichiometric /sup 239/PuO/sub 2/ was examined at 800/sup 0/ to 1500/sup 0/C, using direct and diametral compression. Maximum ductility was observed at 1000/sup 0/C, but above this temperature both strength and ductility decreased and the fracture mode changed from transgranular to intergranular. The deformation activation energy measured at 1000/sup 0/C was 598 kJ/mol. Comparison to the deformation behavior of hypostoichiometric /sup 239/PuO/sub 2-x/ suggests that high-temperature dislocation motion becomes more difficult with increasing O/Pu ratio due to effects of stoichiometry on diffusion rates. Deformation mechanisms in /sup 239/PuO/sub 2/ appear to be a combination of dislocationmore » motion and grain-boundary sliding.« less

  20. Family Life and Developmental Idealism in Yazd, Iran

    PubMed Central

    Abbasi-Shavazi, Mohammad Jalal; Askari-Nodoushan, Abbas

    2012-01-01

    BACKGROUND This paper is motivated by the theory that developmental idealism has been disseminated globally and has become an international force for family and demographic change. Developmental idealism is a set of cultural beliefs and values about development and how development relates to family and demographic behavior. It holds that modern societies are causal forces producing modern families, that modern families help to produce modern societies, and that modern family change is to be expected. OBJECTIVE We examine the extent to which developmental idealism has been disseminated in Iran. We also investigate predictors of the dissemination of developmental idealism. METHODS We use survey data collected in 2007 from a sample of women in Yazd, a city in Iran. We examine the distribution of developmental idealism in the sample and the multivariate predictors of developmental idealism. RESULTS We find considerable support for the expectation that many elements of developmental idealism have been widely disseminated. Statistically significant majorities associate development with particular family attributes, believe that development causes change in families, believe that fertility reductions and age-at-marriage increases help foster development, and perceive family trends in Iran headed toward modernity. As predicted, parental education, respondent education, and income affect adherence to developmental idealism. CONCLUSIONS Developmental idealism has been widely disseminated in Yazd, Iran and is related to social and demographic factors in predicted ways. COMMENTS Although our data come from only one city, we expect that developmental idealism has been widely distributed in Iran, with important implications for family and demographic behavior. PMID:22942772

  1. Ideal Cardiovascular Health and Incident Cardiovascular Events

    PubMed Central

    Ommerborn, Mark J.; Blackshear, Chad T.; Hickson, DeMarc A.; Griswold, Michael E.; Kwatra, Japneet; Djousse, Luc; Clark, Cheryl R.

    2016-01-01

    Introduction The epidemiology of American Heart Association ideal cardiovascular health (CVH) metrics has not been fully examined in African Americans. This study examines associations of CVH metrics with incident cardiovascular disease (CVD) in the Jackson Heart Study, a longitudinal cohort study of CVD in African Americans. Methods Jackson Heart Study participants without CVD (N=4,702) were followed prospectively between 2000 and 2011. Incidence rates and Cox proportional hazard ratios estimated risks for incident CVD (myocardial infarction, stroke, cardiac procedures, and CVD mortality) associated with seven CVH metrics by sex. Analyses were performed in 2015. Results Participants were followed for a median 8.3 years; none had ideal health on all seven CVH metrics. The prevalence of ideal health was low for nutrition, physical activity, BMI, and blood pressure metrics. The age-adjusted CVD incidence rate (IR) per 1,000 person years was highest for individuals with the least ideal health metrics: zero to one (IR=12.5, 95% CI=9.7, 16.1), two (IR=8.2, 95% CI=6.5, 10.4), three (IR=5.7, 95% CI=4.2, 7.6), and four or more (IR=3.4, 95% CI=2.0, 5.9). Adjusting for covariates, individuals with four or more ideal CVH metrics had lower risks of incident CVD compared with those with zero or one ideal CVH metric (hazard ratio, 0.29; 95% CI=0.17, 0.52; p<0.001). Conclusions African Americans with more ideal CVH metrics have lower risks of incident CVD. Comprehensive preventive behavioral and clinical supports should be intensified to improve CVD risk for African Americans with few ideal CVH metrics. PMID:27539974

  2. Interface control and mechanical property improvements in silicon carbide/titanium composites

    NASA Technical Reports Server (NTRS)

    Brewer, W. D.; Unnam, J.

    1982-01-01

    Several composite systems made of titanium matrix reinforced with silicon carbide fiber were investigated to obtain a better understanding of composite-degradation mechanisms and to develop techniques to minimize loss of mechanical properties during fabrication and in service. Emphasis was on interface control by fiber or matrix coatings. X-ray diffraction studies on planar samples showed that the formation of titanium silicides was greatly inhibited by the presence of aluminum or Ti3A1 layers at the fiber-matrix interface, with the Ti3A1 being more effective in reducing the reactions. Fiber studies showed that coating the fiber with a 1-micron-thick layer of aluminum improved the as-fabricated strength of a stoichiometric SiC fiber and reduced the fiber degradation during exposure to composite-fabrication conditions. Applying an interfacial barrier by coating the matrix foils instead of the fibers was found to be an effective method for improving composite strength. Reducing the fabrication temperature also resulted in significant improvements in composite strengths. Good-quality, well-consolidated composites were fabricated at temperatures well below those currently used for SiC-Ti composite fabrication.

  3. Quasi-phase-matched second-harmonic generation of 532 nm radiation in 25 degrees -rotated, x-cut, near-stoichiometric, lithium tantalate fabricated by vapor transport equilibration.

    PubMed

    Hum, D S; Route, R K; Fejer, M M

    2007-04-15

    Quasi-phase-matched second-harmonic generation of 532 nm radiation in 25 degrees -rotated, x-cut, near-stoichiometric lithium tantalate has been performed. Using a face-normal topology for frequency conversion applications allows scalable surface area to avoid surface and volume damage in high-power interactions. First-order, quasi-phase-matched second-harmonic generation was achieved using near-stoichiometric lithium tantalate fabricated by vapor transport equilibration. These crystals supported 1 J of 1064 nm radiation and generated 21 mJ of 532 nm radiation from a 7 ns, Q-switched Nd:YAG laser within a factor of 4.2 of expectation.

  4. Palladium-catalyzed double carbonylation using near stoichiometric carbon monoxide: expedient access to substituted 13C2-labeled phenethylamines.

    PubMed

    Nielsen, Dennis U; Neumann, Karoline; Taaning, Rolf H; Lindhardt, Anders T; Modvig, Amalie; Skrydstrup, Troels

    2012-07-20

    A novel and general approach for (13)C(2)- and (2)H-labeled phenethylamine derivatives has been developed, based on a highly convergent single-step assembly of the carbon skeleton. The efficient incorporation of two carbon-13 isotopes into phenethylamines was accomplished using a palladium-catalyzed double carbonylation of aryl iodides with near stoichiometric carbon monoxide.

  5. Fluorescent tagged episomals for stoichiometric induced pluripotent stem cell reprogramming.

    PubMed

    Schmitt, Christopher E; Morales, Blanca M; Schmitz, Ellen M H; Hawkins, John S; Lizama, Carlos O; Zape, Joan P; Hsiao, Edward C; Zovein, Ann C

    2017-06-05

    Non-integrating episomal vectors have become an important tool for induced pluripotent stem cell reprogramming. The episomal vectors carrying the "Yamanaka reprogramming factors" (Oct4, Klf, Sox2, and L-Myc + Lin28) are critical tools for non-integrating reprogramming of cells to a pluripotent state. However, the reprogramming process remains highly stochastic, and is hampered by an inability to easily identify clones that carry the episomal vectors. We modified the original set of vectors to express spectrally separable fluorescent proteins to allow for enrichment of transfected cells. The vectors were then tested against the standard original vectors for reprogramming efficiency and for the ability to enrich for stoichiometric ratios of factors. The reengineered vectors allow for cell sorting based on reprogramming factor expression. We show that these vectors can assist in tracking episomal expression in individual cells and can select the reprogramming factor dosage. Together, these modified vectors are a useful tool for understanding the reprogramming process and improving induced pluripotent stem cell isolation efficiency.

  6. Elucidating the Wavelength Dependence of Phonon Scattering in Nanoparticle-Matrix Composites using Phonon Spectroscopy

    DTIC Science & Technology

    2016-07-11

    composites with x - ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), Rutherford backscattering spectroscopy...RBS), particle-induced x - ray emission (PIXE), and energy dispersive x - ray spectroscopy (EDX). This work complements earlier works on CdSe...sample shows only In2Se3 and CdIn2Se4 XRD peaks (Figure 1.4e), it is stoichiometrically   Figure 1.4. X - ray diffraction patterns of (a) γ-In2Se3

  7. The Statistical Mechanics of Ideal MHD Turbulence

    NASA Technical Reports Server (NTRS)

    Shebalin, John V.

    2003-01-01

    Turbulence is a universal, nonlinear phenomenon found in all energetic fluid and plasma motion. In particular. understanding magneto hydrodynamic (MHD) turbulence and incorporating its effects in the computation and prediction of the flow of ionized gases in space, for example, are great challenges that must be met if such computations and predictions are to be meaningful. Although a general solution to the "problem of turbulence" does not exist in closed form, numerical integrations allow us to explore the phase space of solutions for both ideal and dissipative flows. For homogeneous, incompressible turbulence, Fourier methods are appropriate, and phase space is defined by the Fourier coefficients of the physical fields. In the case of ideal MHD flows, a fairly robust statistical mechanics has been developed, in which the symmetry and ergodic properties of phase space is understood. A discussion of these properties will illuminate our principal discovery: Coherent structure and randomness co-exist in ideal MHD turbulence. For dissipative flows, as opposed to ideal flows, progress beyond the dimensional analysis of Kolmogorov has been difficult. Here, some possible future directions that draw on the ideal results will also be discussed. Our conclusion will be that while ideal turbulence is now well understood, real turbulence still presents great challenges.

  8. Thermal effects in high-power CW second harmonic generation in Mg-doped stoichiometric lithium tantalate.

    PubMed

    Tovstonog, Sergey V; Kurimura, Sunao; Suzuki, Ikue; Takeno, Kohei; Moriwaki, Shigenori; Ohmae, Noriaki; Mio, Norikatsu; Katagai, Toshio

    2008-07-21

    We investigated thermal behaviors of single-pass second-harmonic generation of continuous wave green radiation with high efficiency by quasi-phase matching in periodically poled Mg-doped stoichiometric lithium tantalate (PPMgSLT). Heat generation turned out to be directly related to the green light absorption in the material. Strong relation between an upper limit of the second harmonic power and confocal parameter was found. Single-pass second-harmonic generation of 16.1 W green power was achieved with 17.6% efficiency in Mg:SLT at room temperature.

  9. Predicting Film Genres with Implicit Ideals

    PubMed Central

    Olney, Andrew McGregor

    2013-01-01

    We present a new approach to defining film genre based on implicit ideals. When viewers rate the likability of a film, they indirectly express their ideal of what a film should be. Across six studies we investigate the category structure that emerges from likability ratings and the category structure that emerges from the features of film. We further compare these data-driven category structures with human annotated film genres. We conclude that film genres are structured more around ideals than around features of film. This finding lends experimental support to the notion that film genres are set of shifting, fuzzy, and highly contextualized psychological categories. PMID:23423823

  10. Predicting film genres with implicit ideals.

    PubMed

    Olney, Andrew McGregor

    2012-01-01

    We present a new approach to defining film genre based on implicit ideals. When viewers rate the likability of a film, they indirectly express their ideal of what a film should be. Across six studies we investigate the category structure that emerges from likability ratings and the category structure that emerges from the features of film. We further compare these data-driven category structures with human annotated film genres. We conclude that film genres are structured more around ideals than around features of film. This finding lends experimental support to the notion that film genres are set of shifting, fuzzy, and highly contextualized psychological categories.

  11. The temporal decline of idealism in two cohorts of medical students at one institution

    PubMed Central

    2014-01-01

    Background A number of studies have indicated that students lose idealistic motivations over the course of medical education, with some identifying the initiation of this decline as occurring as early as the second year of the traditional US curricula. This study builds on prior work testing the hypothesis that a decline in medical student idealism is detectable in the first two years of medical school. Methods The original study sought to identify differences in survey responses between first-year (MS1) and second-year (MS2) medical students at the beginning and end of academic year 2010, on three proxies for idealism. The current study extends that work by administering the same survey items to the same student cohorts at the end of their third and fourth years (MS3 and MS4), respectively. Survey topics included questions on: (a) motivations for pursuing a medical career; (b) specialty choice; and (c) attitudes toward primary care. Principle component analysis was used to extract linear composite variables (LCVs) from responses to each group of questions. Linear regression was then used to test the effect of the six cohort/time-points on each composite variable, controlling for demographic characteristics. Results Idealism in medicine decreased (β = -.113, p < .001) while emphasis on employment and job security increased (β = .146, p < .001) as motivators of pursuing a career in medicine at each medical school stage and time period. Students were more likely to be motivated by student debt over interest in content in specialty choice (β = .077, p = .004) across medical school stages. Negative attitudes towards primary care were most sensitive to MS group and time effects. Both negative/antagonistic views (β = .142, p < .001) and negative/sympathetic views (β = .091, p < .001) of primary care increased over each stage. Conclusions Our results provide further evidence that declines in medical student idealism may occur

  12. Ideal Theory in Semigroups Based on Intersectional Soft Sets

    PubMed Central

    Song, Seok Zun; Jun, Young Bae

    2014-01-01

    The notions of int-soft semigroups and int-soft left (resp., right) ideals are introduced, and several properties are investigated. Using these notions and the notion of inclusive set, characterizations of subsemigroups and left (resp., right) ideals are considered. Using the notion of int-soft products, characterizations of int-soft semigroups and int-soft left (resp., right) ideals are discussed. We prove that the soft intersection of int-soft left (resp., right) ideals (resp., int-soft semigroups) is also int-soft left (resp., right) ideals (resp., int-soft semigroups). The concept of int-soft quasi-ideals is also introduced, and characterization of a regular semigroup is discussed. PMID:25101310

  13. Magnetotransport study of (Sb 1-xBi x) 2Te 3 thin films on mica substrate for ideal topological insulator

    DOE PAGES

    Ni, Yan; Zhang, Zhen; Nlebedim, Cajetan I.; ...

    2016-02-29

    In this study, we deposited high quality (Sb 1–xBi x) 2Te 3 on mica substrate by molecular beam epitaxy and investigated their magnetotransport properties. It is found that the average surface roughness of thin films is lower than 2 nm. Moreover, a local maxima on the sheet resistance is obtained with x = 0.043, indicating a minimization of bulk conductivity at this composition. For (Sb 0.957Bi 0.043) 2Te 3, weak antilocalization with coefficient of -0.43 is observed, confirming the existence of 2D surface states. Moreover Shubnikov-de Hass oscillation behavior occurs under high magnetic field. The 2D carrier density is thenmore » determined as 0.81 × 10 16 m –2, which is lower than that of most TIs reported previously, indicating that (Sb 0.957Bi 0.043) 2Te 3 is close to ideal TI composition of which the Dirac point and Fermi surface cross within the bulk bandgap. Our results thus demonstrate the best estimated composition for ideal TI is close to (Sb 0.957Bi 0.043) 2Te 3 and will be helpful for designing TI-based devices.« less

  14. Moving beyond the van Krevelen Diagram: A New Stoichiometric Approach for Compound Classification in Organisms

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Rivas-Ubach, Albert; Liu, Yina; Bianchi, Thomas S.

    van Krevelen diagrams (O:C vs H:C ratios of elemental formulas) have been widely used in studies to obtain an estimation of the main compound categories present in environmental samples. However, the limits defining a specific compound category based solely on O:C and H:C ratios of elemental formulas have never been accurately listed or proposed to classify metabolites in biological samples. Furthermore, while O:C vs. H:C ratios of elemental formulas can provide an overview of the compound categories, such classification is inefficient because of the large overlap among different compound categories along both axes. We propose a more accurate compound classificationmore » for biological samples analyzed by high-resolution mass spectrometry-based on an assessment of the C:H:O:N:P stoichiometric ratios of over 130,000 elemental formulas of compounds classified in 6 main categories: lipids, peptides, amino-sugars, carbohydrates, nucleotides and phytochemical compounds (oxy-aromatic compounds). Our multidimensional stoichiometric compound classification (MSCC) constraints showed a highly accurate categorization of elemental formulas to the main compound categories in biological samples with over 98% of accuracy representing a substantial improvement over any classification based on the classic van Krevelen diagram. This method represents a significant step forward in environmental research, especially ecological stoichiometry and eco-metabolomics studies, by providing a novel and robust tool to further our understanding the ecosystem structure and function through the chemical characterization of different biological samples.« less

  15. Maintaining ideal body weight counseling sessions

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Brammer, S.H.

    The purpose of this program is to provide employees with the motivation, knowledge and skills necessary to maintain ideal body weight throughout life. The target audience for this program, which is conducted in an industrial setting, is the employee 40 years of age or younger who is at or near his/her ideal body weight.

  16. The Ideal Man and Woman According to University Students

    ERIC Educational Resources Information Center

    Weinstein, Lawrence; Laverghetta, Antonio V.; Peterson, Scott A.

    2009-01-01

    The present study determined if the ideal man has changed over the years and who and what the ideal woman is. We asked students at Cameron University to rate the importance of character traits that define the ideal man and woman. Subjects also provided examples of famous people exemplifying the ideal, good, average, and inferior man and woman. We…

  17. Variations in eco-enzymatic stoichiometric and microbial characteristics in paddy soil as affected by long-term integrated organic-inorganic fertilization

    PubMed Central

    Lin, Sen; Wang, Shaoxian; Si, Yuanli; Yang, Wenhao; Zhu, Shaowei

    2017-01-01

    To investigate the effects of different nutrient management regimes on the soil chemical, eco-enzymatic stoichiometric and microbial characteristics, soil samples were collected from a 30-year, long-term field experiment with six plots growing rice. The results showed that as integrated fertilization increased, so did the concentrations of soil total or available nutrients and microbial biomass carbon (MBC). Our results also found enhanced soil basal respiration and cumulative carbon mineralization compared to chemical fertilization alone at the same nutrient doses. The activities of soil protease (Pro), β-glucosidase (βG), N-acetyl-glucosaminidase (NAG) and acid phosphatase (AP) from the integrated fertilization treatments were significantly higher than those of the treatments without organic manure, so did the activities of soil leucyl aminopeptidase (LAP) and urease (Ure) from the treatment with organic manure in addition to farmer practise fertilization (NPKM2). The stoichiometric ratios, expressed as lnβG/ln(NAG+LAP)/lnPro/lnUre/lnAP, ranged from 1:0.94:1.04:0.67:1.01 to 1:0.98:1.10:0.78:1.25, indicating that the acquisition of C, N and P changed consistently and synchronously under different nutrient management strategies. Integrated fertilization was more beneficial to the acquisition and utilization of soil organic carbon compared to low-molecular-weight organic nitrogen. We concluded that protease and urease should be considered in eco-enzymatic stoichiometric assessments for the hydrolysis of proteins, amino acids, carbohydrates and phosphomonoesters in soil, and integrated fertilization with chemical fertilizers and organic manure should be recommended as a preferable nutrient management system for intensive rice cultivation. PMID:29253000

  18. Variations in eco-enzymatic stoichiometric and microbial characteristics in paddy soil as affected by long-term integrated organic-inorganic fertilization.

    PubMed

    Lin, Sen; Wang, Shaoxian; Si, Yuanli; Yang, Wenhao; Zhu, Shaowei; Ni, Wuzhong

    2017-01-01

    To investigate the effects of different nutrient management regimes on the soil chemical, eco-enzymatic stoichiometric and microbial characteristics, soil samples were collected from a 30-year, long-term field experiment with six plots growing rice. The results showed that as integrated fertilization increased, so did the concentrations of soil total or available nutrients and microbial biomass carbon (MBC). Our results also found enhanced soil basal respiration and cumulative carbon mineralization compared to chemical fertilization alone at the same nutrient doses. The activities of soil protease (Pro), β-glucosidase (βG), N-acetyl-glucosaminidase (NAG) and acid phosphatase (AP) from the integrated fertilization treatments were significantly higher than those of the treatments without organic manure, so did the activities of soil leucyl aminopeptidase (LAP) and urease (Ure) from the treatment with organic manure in addition to farmer practise fertilization (NPKM2). The stoichiometric ratios, expressed as lnβG/ln(NAG+LAP)/lnPro/lnUre/lnAP, ranged from 1:0.94:1.04:0.67:1.01 to 1:0.98:1.10:0.78:1.25, indicating that the acquisition of C, N and P changed consistently and synchronously under different nutrient management strategies. Integrated fertilization was more beneficial to the acquisition and utilization of soil organic carbon compared to low-molecular-weight organic nitrogen. We concluded that protease and urease should be considered in eco-enzymatic stoichiometric assessments for the hydrolysis of proteins, amino acids, carbohydrates and phosphomonoesters in soil, and integrated fertilization with chemical fertilizers and organic manure should be recommended as a preferable nutrient management system for intensive rice cultivation.

  19. Atomistic models of Cu diffusion in CuInSe2 under variations in composition

    NASA Astrophysics Data System (ADS)

    Sommer, David E.; Dunham, Scott T.

    2018-03-01

    We construct an analytic model for the composition dependence of the vacancy-mediated Cu diffusion coefficient in undoped CuInSe2 using parameters from density functional theory. The applicability of this model is supported numerically with kinetic lattice Monte Carlo and Onsager transport tensors. We discuss how this model relates to experimental measurements of Cu diffusion, arguing that our results can account for significant contributions to the bulk diffusion of Cu tracers in non-stoichiometric CuInSe2.

  20. Idealism and materialism in perception.

    PubMed

    Rose, David; Brown, Dora

    2015-01-01

    Koenderink (2014, Perception, 43, 1-6) has said most Perception readers are deluded, because they believe an 'All Seeing Eye' observes an objective reality. We trace the source of Koenderink's assertion to his metaphysical idealism, and point to two major weaknesses in his position-namely, its dualism and foundationalism. We counter with arguments from modern philosophy of science for the existence of an objective material reality, contrast Koenderink's enactivism to his idealism, and point to ways in which phenomenology and cognitive science are complementary and not mutually exclusive.

  1. Distillation-based Droplet Modeling of Non-Ideal Oxygenated Gasoline Blends: Investigating the Role of Droplet Evaporation on PM Emissions

    DOE PAGES

    Burke, Stephen C.; Ratcliff, Matthew; McCormick, Robert; ...

    2017-03-28

    In some studies, a relationship has been observed between increasing ethanol content in gasoline and increased particulate matter (PM) emissions from vehicles equipped with spark ignition engines. The fundamental cause of the PM increase seen for moderate ethanol concentrations is not well understood. Ethanol features a greater heat of vaporization (HOV) than gasoline and also influences vaporization by altering the liquid and vapor composition throughout the distillation process. A droplet vaporization model was developed to explore ethanol's effect on the evaporation of aromatic compounds known to be PM precursors. The evolving droplet composition is modeled as a distillation process, withmore » non-ideal interactions between oxygenates and hydrocarbons accounted for using UNIFAC group contribution theory. Predicted composition and distillation curves were validated by experiments. Detailed hydrocarbon analysis was applied to fuel samples and to distillate fractions, and used as input for the initial droplet composition. With composition calculated throughout the distillation, the changing HOV and other physical properties can be found using reference data. The droplet can thus be modeled in terms of energy transfer, which in turn provides the transient mass transfer, droplet temperature, and droplet diameter. Model predictions suggest that non-ideal vapor-liquid equilibrium along with an increase in HOV can alter the droplet composition evolution. Results predict that the presence of ethanol causes enrichment of the higher boiling fractions (T90+) in the aromatic components as well as lengthens the droplet lifetime. A simulation of the evaporation process in a transient environment as experienced within an engine cylinder predicts a decrease in mixing time of the heaviest fractions of the fuel prior to spark initiation, possibly explaining observations linking ethanol to PM.« less

  2. Distillation-based Droplet Modeling of Non-Ideal Oxygenated Gasoline Blends: Investigating the Role of Droplet Evaporation on PM Emissions

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Burke, Stephen C.; Ratcliff, Matthew; McCormick, Robert

    In some studies, a relationship has been observed between increasing ethanol content in gasoline and increased particulate matter (PM) emissions from vehicles equipped with spark ignition engines. The fundamental cause of the PM increase seen for moderate ethanol concentrations is not well understood. Ethanol features a greater heat of vaporization (HOV) than gasoline and also influences vaporization by altering the liquid and vapor composition throughout the distillation process. A droplet vaporization model was developed to explore ethanol's effect on the evaporation of aromatic compounds known to be PM precursors. The evolving droplet composition is modeled as a distillation process, withmore » non-ideal interactions between oxygenates and hydrocarbons accounted for using UNIFAC group contribution theory. Predicted composition and distillation curves were validated by experiments. Detailed hydrocarbon analysis was applied to fuel samples and to distillate fractions, and used as input for the initial droplet composition. With composition calculated throughout the distillation, the changing HOV and other physical properties can be found using reference data. The droplet can thus be modeled in terms of energy transfer, which in turn provides the transient mass transfer, droplet temperature, and droplet diameter. Model predictions suggest that non-ideal vapor-liquid equilibrium along with an increase in HOV can alter the droplet composition evolution. Results predict that the presence of ethanol causes enrichment of the higher boiling fractions (T90+) in the aromatic components as well as lengthens the droplet lifetime. A simulation of the evaporation process in a transient environment as experienced within an engine cylinder predicts a decrease in mixing time of the heaviest fractions of the fuel prior to spark initiation, possibly explaining observations linking ethanol to PM.« less

  3. Effect of composition and strain on the electrical properties of LaNiO3 thin films

    NASA Astrophysics Data System (ADS)

    Zhu, Mingwei; Komissinskiy, Philipp; Radetinac, Aldin; Vafaee, Mehran; Wang, Zhanjie; Alff, Lambert

    2013-09-01

    The Ni content of LaNi1-xO3 epitaxial thin films grown by pulsed laser deposition has been varied by ablation from targets with different composition. While tensile strain and Ni substoichiometry reduce the conductivity, nearly stoichiometric and unstrained films show reproducibly resistivities below 100 μΩ × cm. Since the thermodynamic instability of the Ni3+ state drives defect formation, Ni defect engineering is the key to obtain highly conducting LaNiO3 thin films.

  4. The Influence of Water Vapor on the Stability and Processing of Hybrid Perovskite Solar Cells Made from Non-Stoichiometric Precursor Mixtures.

    PubMed

    Petrus, Michiel L; Hu, Yinghong; Moia, Davide; Calado, Philip; Leguy, Aurélien M A; Barnes, Piers R F; Docampo, Pablo

    2016-09-22

    We investigated the influence of moisture on methylammonium lead iodide perovskite (MAPbI 3 ) films and solar cells derived from non-stoichiometric precursor mixtures. We followed both the structural changes under controlled air humidity through in situ X-ray diffraction, and the electronic behavior of devices prepared from these films. A small PbI 2 excess in the films improved the stability of the perovskite compared to stoichiometric samples. We assign this to excess PbI 2 layers at the perovskite grain boundaries or to the termination of the perovskite crystals with Pb and I. In contrast, the MAI-excess films composed of smaller perovskite crystals showed increased electronic disorder and reduced device performance owing to poor charge collection. Upon exposure to moisture followed by dehydration (so-called solvent annealing), these films recrystallized to form larger, highly oriented crystals with fewer electronic defects and a remarkable improvement in photocurrent and photovoltaic efficiency. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Quantitative analysis of interfacial chemistry in TiC/Ti composite using electron-energy-loss spectroscopy

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Gu, M.; Jiang, W.; Zhang, G.

    Due to titanium carbide`s physical and elastic properties, titanium carbide particles are widely used as a reinforcement in titanium-alloy-based composites. Previous studies have shown that no obvious reaction products were detected on the interface region in TiC/Ti alloy systems; instead, a nonstoichiometric region in the TiC particle between the Ti{sub 6}Al{sub 4}V alloy and the stoichiometric TiC was found. However, the nature and the extent of the nonstoichiometric zone have not been quantitatively described. The present communication reports some results of a parallel electron-energy-loss spectroscopy (PEELS) study on a 10 vol pct TiC-particle-reinforced IMI-829 metal-matrix composite.

  6. Plant–herbivore–decomposer stoichiometric mismatches and nutrient cycling in ecosystems

    PubMed Central

    Cherif, Mehdi; Loreau, Michel

    2013-01-01

    Plant stoichiometry is thought to have a major influence on how herbivores affect nutrient availability in ecosystems. Most conceptual models predict that plants with high nutrient contents increase nutrient excretion by herbivores, in turn raising nutrient availability. To test this hypothesis, we built a stoichiometrically explicit model that includes a simple but thorough description of the processes of herbivory and decomposition. Our results challenge traditional views of herbivore impacts on nutrient availability in many ways. They show that the relationship between plant nutrient content and the impact of herbivores predicted by conceptual models holds only at high plant nutrient contents. At low plant nutrient contents, the impact of herbivores is mediated by the mineralization/immobilization of nutrients by decomposers and by the type of resource limiting the growth of decomposers. Both parameters are functions of the mismatch between plant and decomposer stoichiometries. Our work provides new predictions about the impacts of herbivores on ecosystem fertility that depend on critical interactions between plant, herbivore and decomposer stoichiometries in ecosystems. PMID:23303537

  7. Medical learning curves and the Kantian ideal.

    PubMed

    Le Morvan, P; Stock, B

    2005-09-01

    A hitherto unexamined problem for the "Kantian ideal" that one should always treat patients as ends in themselves, and never only as a means to other ends, is explored in this paper. The problem consists of a prima facie conflict between this Kantian ideal and the reality of medical practice. This conflict arises because, at least presently, medical practitioners can only acquire certain skills and abilities by practising on live, human patients, and given the inevitability and ubiquity of learning curves, this learning requires some patients to be treated only as a means to this end. A number of ways of attempting to establish the compatibility of the Kantian Ideal with the reality of medical practice are considered. Each attempt is found to be unsuccessful. Accordingly, until a way is found to reconcile them, we conclude that the Kantian ideal is inconsistent with the reality of medical practice.

  8. Medical learning curves and the Kantian ideal

    PubMed Central

    Le Morvan, P; Stock, B

    2005-01-01

    A hitherto unexamined problem for the "Kantian ideal" that one should always treat patients as ends in themselves, and never only as a means to other ends, is explored in this paper. The problem consists of a prima facie conflict between this Kantian ideal and the reality of medical practice. This conflict arises because, at least presently, medical practitioners can only acquire certain skills and abilities by practising on live, human patients, and given the inevitability and ubiquity of learning curves, this learning requires some patients to be treated only as a means to this end. A number of ways of attempting to establish the compatibility of the Kantian Ideal with the reality of medical practice are considered. Each attempt is found to be unsuccessful. Accordingly, until a way is found to reconcile them, we conclude that the Kantian ideal is inconsistent with the reality of medical practice. PMID:16131552

  9. Dy3TaO7, A stoichiometric spin glass and the effect of disorder via chemical substitution in the Dy3-xYxTaO7 (0 ≤ x ≤ 3) solid solution

    NASA Astrophysics Data System (ADS)

    Gómez-García, J. Francisco; Bucio, Lauro; Tavizon, Gustavo

    2018-01-01

    In this work, we present both structural and magnetic (DC magnetization and AC susceptibility) studies of the Dy3-xYxTaO7 solid solution. The structural characterization of samples was performed by Rietveld refinements of the X-ray diffraction data. All compounds crystallized in a weberite-related structure in the orthorhombic C2221 space group (No. 20); the variations of the lattice parameters obey the Vegard´s law in the whole range of composition. DC magnetic measurements of the Dy3-xYxTaO7 system showed a Curie-Weiss paramagnetic behaviour, with antiferromagnetic interactions at T>150 K. Below 3 K a spin glass behaviour in the 0 ≤ x ≤ 1 range of the solid solution was observed. The stoichiometric Dy3TaO7 compound showed spin glass behaviour although there is no evidence of structural disorder. For some Y3+ doped compounds (x = 0.33, 0.66 and 1.0), chemical disorder reduced the freezing temperature (Tg) values with a ×1/3 dependence. Cole-Cole analysis of the AC magnetic field response showed similar phenomenological parameters for the stoichiometric (x = 0) and the Y3+ doped compounds with spin glassiness, suggesting an analogous mechanism for these compounds. For the Dy3-xYxTaO7 system, in which the spin glass behaviour seems to exhibit a critical concentration, a magnetic phase diagram is proposed.

  10. [The style of leadership idealized by nurses].

    PubMed

    Higa, Elza de Fátima Ribeiro; Trevizan, Maria Auxiliadora

    2005-01-01

    This study focuses on nursing leadership on the basis of Grid theories. According to the authors, these theories are an alternative that allows for leadership development in nursing. The research aimed to identify and analyze the style of leadership idealized by nurses, according to their own view, and to compare the styles of leadership idealized by nurses between the two research institutions. Study subjects were 13 nurses. The results show that nurses at both institutions equally mention they idealize style 9.9, followed by 5.5 and 1.9, with a tendency to reject styles 9.1 and 1.1.

  11. Thermodynamics of stoichiometric biochemical networks in living systems far from equilibrium.

    PubMed

    Qian, Hong; Beard, Daniel A

    2005-04-22

    The principles of thermodynamics apply to both equilibrium and nonequilibrium biochemical systems. The mathematical machinery of the classic thermodynamics, however, mainly applies to systems in equilibrium. We introduce a thermodynamic formalism for the study of metabolic biochemical reaction (open, nonlinear) networks in both time-dependent and time-independent nonequilibrium states. Classical concepts in equilibrium thermodynamics-enthalpy, entropy, and Gibbs free energy of biochemical reaction systems-are generalized to nonequilibrium settings. Chemical motive force, heat dissipation rate, and entropy production (creation) rate, key concepts in nonequilibrium systems, are introduced. Dynamic equations for the thermodynamic quantities are presented in terms of the key observables of a biochemical network: stoichiometric matrix Q, reaction fluxes J, and chemical potentials of species mu without evoking empirical rate laws. Energy conservation and the Second Law are established for steady-state and dynamic biochemical networks. The theory provides the physiochemical basis for analyzing large-scale metabolic networks in living organisms.

  12. Ultraviolet-infrared laser-induced domain inversion in MgO-doped congruent LiNbO3 and near stoichiometric LiTaO3 crystals

    NASA Astrophysics Data System (ADS)

    Zhi, Ya'nan; Qu, Weijuan; Liu, De'an; Sun, Jianfeng; Yan, Aimin; Liu, Liren

    2008-08-01

    Laser-induced domain inversion is a promising technique for domain engineering in LiNbO3 and LiTaO3. The ultraviolet-infrared laser induced domain inversions in MgO-doped congruent LiNbO3 and near stoichiometric LiTaO3 crystals are investigated for the first time here. Within the wavelength range from 351 to 799 nm, the different reductions of nucleation field induced by the focused continuous laser irradiation are systematically investigated in the MgO-doped congruent LiNbO3 crystals. The investigation of ultrashort-pulse laser-induced domain inversion in MgO-doped congruent LiNbO3 is performed with 800 nm wavelength irradiation. The focused continuous ultraviolet laser-induced ferroelectric domain inversion in the near stoichiometric LiTaO3 is also investigated. The different physical explanations, based on space charge field and defect formation, are presented for the laser-induced domain inversion, and the solid experimental proofs are also presented. The results provide the solid experimental proofs and feasible schemes for the further investigation of laser-induced domain engineering in MgO-doped LiNbO3 and near stoichiometric LiTaO3 crystals. The important characteristics of domain inversion, including domain wall and internal field, in LiNbO3 crystals are also investigated by the digital holographic interferometry with an improved reconstruction method, and some creative experimental results and conclusions are achieved.

  13. Method of preparing corrosion resistant composite materials

    DOEpatents

    Kaun, Thomas D.

    1993-01-01

    Method of manufacture of ceramic materials which require stability in severely-corrosive environment having high alkali-metal activity, high sulfur/sulfide activity and/or molten halides at temperatures of 200.degree.-550.degree. C. or organic salt (including SO.sub.2 and SO.sub.2 Cl.sub.2) at temperatures of 25.degree.-200.degree. C. These surfide ceramics form stoichiometric (single-phase) compounds with sulfides of Ca, Li, Na, K, Al, Mg, Si, Y, La, Ce, Ga, Ba, Zr and Sr and show melting-points that are sufficiently low and have excellent wettability with many metals (Fe, Ni, Mo) to easily form metal/ceramic seals. Ceramic compositions are also formulated to adequately match thermal expansion coefficient of adjacent metal components.

  14. Ideal strength of bcc molybdenum and niobium

    NASA Astrophysics Data System (ADS)

    Luo, Weidong; Roundy, D.; Cohen, Marvin L.; Morris, J. W.

    2002-09-01

    The behavior of bcc Mo and Nb under large strain was investigated using the ab initio pseudopotential density-functional method. We calculated the ideal shear strength for the {211}<111> and {011}<111> slip systems and the ideal tensile strength in the <100> direction, which are believed to provide the minimum shear and tensile strengths. As either material is sheared in either of the two systems, it evolves toward a stress-free tetragonal structure that defines a saddle point in the strain-energy surface. The inflection point on the path to this tetragonal ``saddle-point'' structure sets the ideal shear strength. When either material is strained in tension along <100>, it initially follows the tetragonal, ``Bain,'' path toward a stress-free fcc structure. However, before the strained crystal reaches fcc, its symmetry changes from tetragonal to orthorhombic; on continued strain it evolves toward the same tetragonal saddle point that is reached in shear. In Mo, the symmetry break occurs after the point of maximum tensile stress has been passed, so the ideal strength is associated with the fcc extremum as in W. However, a Nb crystal strained in <100> becomes orthorhombic at tensile stress below the ideal strength. The ideal tensile strength of Nb is associated with the tetragonal saddle point and is caused by failure in shear rather than tension. In dimensionless form, the ideal shear and tensile strengths of Mo (τ*=τm/G111=0.12, σ*=σm/E100=0.078) are essentially identical to those previously calculated for W. Nb is anomalous. Its dimensionless shear strength is unusually high, τ*=0.15, even though the saddle-point structure that causes it is similar to that in Mo and W, while its dimensionless tensile strength, σ*=0.079, is almost the same as that of Mo and W, even though the saddle-point structure is quite different.

  15. Composite-Metal-Matrix Arc-Spray Process

    NASA Technical Reports Server (NTRS)

    Westfall, Leonard J.

    1987-01-01

    Arc-spray "monotape" process automated, low in cost, and produces at high rate. Ideal for development of new metal-matrix composites. "Monotape" reproducible and of high quality. Process carried out in controlled gas environment with programmable matrix-deposition rates, resulting in significant cost saving

  16. Ideal and Nonideal Reasoning in Educational Theory

    ERIC Educational Resources Information Center

    Jaggar, Alison M.

    2015-01-01

    The terms "ideal theory" and "nonideal theory" are used in contemporary Anglophone political philosophy to identify alternative methodological approaches for justifying normative claims. Each term is used in multiple ways. In this article Alison M. Jaggar disentangles several versions of ideal and nonideal theory with a view to…

  17. Idealized cultural beliefs about gender: implications for mental health.

    PubMed

    Mahalingam, Ramaswami; Jackson, Benita

    2007-12-01

    In this paper, we examined the relationship between culture-specific ideals (chastity, masculinity, caste beliefs) and self-esteem, shame and depression using an idealized cultural model proposed by Mahalingam (2006, In: Mahalingam R (ed) Cultural psychology of immigrants. Lawrence Erlbaum, Mahwah, NJ, pp 1-14). Participants were from communities with a history of extreme male-biased sex ratios in Tamilnadu, India (N = 785). We hypothesized a dual-process model of self-appraisals suggesting that achieving idealized cultural identities would increase both self-esteem and shame, with the latter leading to depression, even after controlling for key covariates. We tested this using structural equation modeling. The proposed idealized cultural identities model had an excellent fit (CFI = 0.99); the effect of idealized identities on self-esteem, shame and depression differed by gender. Idealized beliefs about gender relate to psychological well-being in gender specific ways in extreme son preference communities. We discuss implications of these findings for future research and community-based interventions.

  18. DNA flow cytometry of human spermatozoa: consistent stoichiometric staining of sperm DNA using a novel decondensation protocol.

    PubMed

    Kovács, Tamás; Békési, Gyöngyi; Fábián, Akos; Rákosy, Zsuzsa; Horváth, Gábor; Mátyus, László; Balázs, Margit; Jenei, Attila

    2008-10-01

    Rapid flow cytometric measurement of the frequency of aneuploid human sperms is in increasing demand but development of an exploitable method is hindered by difficulties of stoichiometric staining of sperm DNA. An aggressive decondensation protocol is needed after which cell integrity still remains intact. We used flow cytometry to examine the effect of lithium diiodosalicylate (LIS, chaotropic agent) on fluorescence intensity of propidium iodide-treated human spermatozoa from 10 normozoospermic men. When flow cytometric identification of diploid spermatozoa was achieved, validation was performed after sorting by three-color FISH. In contrast with the extremely variable histograms of nondecondensed sperms, consistent identification of haploid and diploid spermatozoa was possible if samples were decondensed with LIS prior to flow cytometry. A 76-fold enrichment of diploid sperms was observed in the sorted fractions by FISH. A significant correlation was found between the proportion of sorted cells and of diploid sperms by FISH. Application of LIS during the preparation of sperm for flow cytometry appears to ensure the stoichiometric staining of sperm DNA, making quantification of aneuploid sperm percentage possible. To our knowledge this is the first report in terms of separating spermatozoa with confirmedly abnormal chromosomal content. High correlation between the proportion of cells identified as having double DNA content by flow cytometry and diploid sperm by FISH allows rapid calculation of diploidy rate. Copyright 2008 International Society for Advancement of Cytometry.

  19. Enhanced hexose fermentation by Saccharomyces cerevisiae through integration of stoichiometric modeling and genetic screening.

    PubMed

    Quarterman, Josh; Kim, Soo Rin; Kim, Pan-Jun; Jin, Yong-Su

    2015-01-20

    In order to determine beneficial gene deletions for ethanol production by the yeast Saccharomyces cerevisiae, we performed an in silico gene deletion experiment based on a genome-scale metabolic model. Genes coding for two oxidative phosphorylation reactions (cytochrome c oxidase and ubiquinol cytochrome c reductase) were identified by the model-based simulation as potential deletion targets for enhancing ethanol production and maintaining acceptable overall growth rate in oxygen-limited conditions. Since the two target enzymes are composed of multiple subunits, we conducted a genetic screening study to evaluate the in silico results and compare the effect of deleting various portions of the respiratory enzyme complexes. Over two-thirds of the knockout mutants identified by the in silico study did exhibit experimental behavior in qualitative agreement with model predictions, but the exceptions illustrate the limitation of using a purely stoichiometric model-based approach. Furthermore, there was a substantial quantitative variation in phenotype among the various respiration-deficient mutants that were screened in this study, and three genes encoding respiratory enzyme subunits were identified as the best knockout targets for improving hexose fermentation in microaerobic conditions. Specifically, deletion of either COX9 or QCR9 resulted in higher ethanol production rates than the parental strain by 37% and 27%, respectively, with slight growth disadvantages. Also, deletion of QCR6 led to improved ethanol production rate by 24% with no growth disadvantage. The beneficial effects of these gene deletions were consistently demonstrated in different strain backgrounds and with four common hexoses. The combination of stoichiometric modeling and genetic screening using a systematic knockout collection was useful for narrowing a large set of gene targets and identifying targets of interest. Copyright © 2014 Elsevier B.V. All rights reserved.

  20. Susceptibility for thin ideal media and eating styles.

    PubMed

    Anschutz, Doeschka J; Engels, Rutger C M E; Van Strien, Tatjana

    2008-03-01

    This study examined the relations between susceptibility for thin ideal media and restrained, emotional and external eating, directly and indirectly through body dissatisfaction. Thin ideal media susceptibility, body dissatisfaction and eating styles were measured in a sample of 163 female students. Structural equation modelling was used for analyses, controlling for BMI. Higher susceptibility for thin ideal media was directly related to higher scores on all eating styles, and indirectly related to higher restrained and emotional eating through elevated levels of body dissatisfaction. So, thin ideal media susceptibility was not only related to restraint through body dissatisfaction, but also directly. Emotional eaters might be more vulnerable for negative affect, whereas external eaters might be more sensitive to external cues in general.

  1. Composition for detecting uranyl

    DOEpatents

    Baylor, L.C.; Stephens, S.M.

    1994-01-01

    The present invention relates to an indicator composition for use in spectrophotometric detection of a substance in a solution, and a method for making the composition. Useful indicators are sensitive to the particular substance being measured, but are unaffected by the fluid and other chemical species that may be present in the fluid. Optical indicators are used to measure the uranium concentration of process solutions in facilities for extracting uranium from ores, production of nuclear fuels, and reprocessing of irradiated fuels. The composition comprises an organohalide covalently bonded to an indicator for the substance, in such a manner that the product is itself an indicator that provides increased spectral resolution for detecting the substance. The indicator is preferably arsenazo III and the organohalide is preferably cyanuric chloride. These form a composition that is ideally suited for detecting uranyl.

  2. Heat of combustion of tantalum-tungsten oxide thermite composites

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Cervantes, Octavio G.; Department of Chemical Engineering and Materials Science, University of California, Davis, CA 95616; Kuntz, Joshua D.

    2010-12-15

    The heat of combustion of two distinctly synthesized stoichiometric tantalum-tungsten oxide energetic composites was investigated by bomb calorimetry. One composite was synthesized using a sol-gel (SG) derived method in which micrometric-scale tantalum is immobilized in a tungsten oxide three-dimensional nanostructured network structure. The second energetic composite was made from the mixing of micrometric-scale tantalum and commercially available (CA) nanometric tungsten oxide powders. The energetic composites were consolidated using the spark plasma sintering (SPS) technique under a 300 MPa pressure and at temperatures of 25, 400, and 500 C. For samples consolidated at 25 C, the density of the CA compositemore » is 61.65 {+-} 1.07% in comparison to 56.41 {+-} 1.19% for the SG derived composite. In contrast, the resulting densities of the SG composite are higher than the CA composite for samples consolidated at 400 and 500 C. The theoretical maximum density for the SG composite consolidated to 400 and 500 C are 81.30 {+-} 0.58% and 84.42 {+-} 0.62%, respectively. The theoretical maximum density of the CA composite consolidated to 400 and 500 C are 74.54 {+-} 0.80% and 77.90 {+-} 0.79%, respectively. X-ray diffraction analyses showed an increase of pre-reaction of the constituents with an increase in the consolidation temperature. The increase in pre-reaction results in lower stored energy content for samples consolidated to 400 and 500 C in comparison to samples consolidated at 25 C. (author)« less

  3. Using Drama in the Composition Class.

    ERIC Educational Resources Information Center

    Radavich, David A.

    Dramatic texts are an ideal pedagogical tool for clarifying certain aspects of communication such as authorial stance, point of view, role, persona, impersonation, ethos, shared communal values, cultural assumptions, genre expectations, audience, performance, dialogue, and enactment. Using dramatic texts in a composition class can broaden student…

  4. Promoting Spiritual Ideals through Design Thinking in Public Schools

    ERIC Educational Resources Information Center

    Tan, Charlene; Wong, Yew-Leong

    2012-01-01

    Against a backdrop of the debates on religious education in public or state schools, we argue for the introduction of "spiritual ideals" into the public school curriculum. We distinguish our notion of spiritual ideals from "religious ideals" as conceptualised by De Ruyter and Merry. While we agree with De Ruyter and Merry that…

  5. Effect of Flame Stabilizer Design on Performance and Exhaust Pollutants of a Two-Row Swirl-Can Combustor Operated to Near-Stoichiometric Conditions

    NASA Technical Reports Server (NTRS)

    Biaglow, James A.; Trout, Arthur M.

    1977-01-01

    Emissions and performance characteristics were determined for two full annulus modular combustors operated to near stoichiometric fuel air ratios. The tests were conducted to obtain stoichiometric data at inlet air temperatures from 756 to 894 K and to determine the effects of a flat plate circular flame stabilizer with upstream fuel injection and a contraswirl flame stabilizer with downstream fuel injection. Levels of unburned hydrocarbons were below 0.50 gram per kilogram of fuel for both combustors and thus there was no detectable difference in the two methods of fuel injection. The contraswirl flame stabilizer did not produce the level of mixing obtained with a flat plate circular flame stabilizer. It did produce higher levels of oxides of nitrogen, which peaked at a fuel air ratio of 0.037. For the flat plate circular flame stabilizer, oxides of nitrogen emission levels were still increasing with fuel air ratio to the maximum tested value of 0.045.

  6. Msn2 Coordinates a Stoichiometric Gene Expression Program

    PubMed Central

    Stewart-Ornstein, Jacob; Nelson, Christopher; DeRisi, Joe; Weissman, Jonathan S.; El-Samad, Hana

    2014-01-01

    Summary Background Many cellular processes operate in an “analog” regime in which the magnitude of the response is precisely tailored to the intensity of the stimulus. In order to maintain the coherence of such responses, the cell must provide for proportional expression of multiple target genes across a wide dynamic range of induction states. Our understanding of the strategies used to achieve graded gene regulation is limited. Results In this work, we document a relationship between stress responsive gene expression and the transcription factor Msn2 that is graded over a large range of Msn2 cocnentrations. We use computational modeling, in vivo, and in vitro analysis to dissect the roots of this relationship. Our studies reveal a simple and general strategy based on non-cooperative low-affinity interactions between Msn2 and its cognate binding sites, as well as competition over a large number of Msn2 binding sites in the genome relative to the number of Msn2 molecules. Conclusions In addition to enabling precise tuning of gene expression to the state of the environment, this strategy ensures co-linear activation of target genes, allowing for stoichiometric expression of large groups of genes without extensive promoter tuning. Furthermore, such a strategy enables precise modulation of the activity of any given promoter by addition of binding sites without altering the qualitative relationship between different genes in a regulon. This feature renders a given regulon highly ‘evolvable’. PMID:24210615

  7. Childhood Lifestyle and Clinical Determinants of Adult Ideal

    PubMed Central

    Laitinen, Tomi T.; Pahkala, Katja; Venn, Alison; Woo, Jessica G; Oikonen, Mervi; Dwyer, Terence; Mikkilä, Vera; Hutri-Kähönen, Nina; Smith, Kylie J.; Gall, Seana L.; Morrison, John A.; Viikari, Jorma S.A.; Raitakari, Olli T.; Magnussen, Costan G.; Juonala, Markus

    2013-01-01

    Background The American Heart Association recently defined ideal cardiovascular health by simultaneous presence of seven health behaviors and factors. The concept is associated with cardiovascular disease incidence, and cardiovascular disease and all-cause mortality. To effectively promote ideal cardiovascular health already early in life, childhood factors predicting future ideal cardiovascular health should be investigated. Our aim was thus to comprehensively explore childhood determinants of adult ideal cardiovascular health in population based cohorts from three continents. Methods The sample comprised a total of 4409 participants aged 3–19 years at baseline from the Cardiovascular Risk in Young Finns Study (YFS; N=1883) from Finland, Childhood Determinants of Adult Health Study (CDAH; N=1803) from Australia and Princeton Follow-up Study (PFS; N=723) from the United States. Participants were re-examined 19–31 years later when aged 30–48 years. Results In multivariable analyses, independent childhood predictors of adult ideal cardiovascular health were family socioeconomic status (P<0.01; direct association) and BMI (P<0.001; inverse association) in all cohorts. In addition, blood pressure (P=0.007), LDL-cholesterol (P<0.001) and parental smoking (P=0.006) in the YFS, and own smoking (P=0.001) in CDAH were inversely associated with future ideal cardiovascular health. Conclusions Among several lifestyle and clinical indicators studied, higher family socioeconomic status and non-smoking (parental/own) in childhood independently predict ideal cardiovascular health in adulthood. As atherosclerotic cardiovascular diseases are rooted in childhood, our findings suggest that special attention could be paid to children who are from low socioeconomic status families, and who smoke or whose parents smoke, to prevent cardiovascular disease morbidity and mortality. PMID:24075574

  8. On the union of graded prime ideals

    NASA Astrophysics Data System (ADS)

    Uregen, Rabia Nagehan; Tekir, Unsal; Hakan Oral, Kursat

    2016-01-01

    In this paper we investigate graded compactly packed rings, which is defined as; if any graded ideal I of R is contained in the union of a family of graded prime ideals of R, then I is actually contained in one of the graded prime ideals of the family. We give some characterizations of graded compactly packed rings. Further, we examine this property on h - Spec(R). We also define a generalization of graded compactly packed rings, the graded coprimely packed rings. We show that R is a graded compactly packed ring if and only if R is a graded coprimely packed ring whenever R be a graded integral domain and h - dim R = 1.

  9. Why Education in Public Schools Should Include Religious Ideals

    ERIC Educational Resources Information Center

    de Ruyter, Doret J.; Merry, Michael S.

    2009-01-01

    This article aims to open a new line of debate about religion in public schools by focusing on religious ideals. The article begins with an elucidation of the concept "religious ideals" and an explanation of the notion of reasonable pluralism, in order to be able to explore the dangers and positive contributions of religious ideals and their…

  10. Idealization of the analyst by the young adult.

    PubMed

    Chused, J F

    1987-01-01

    Idealization is an intrapsychic process that serves many functions. In addition to its use defensively and for gratification of libidinal and aggressive drive derivatives, it can contribute to developmental progression, particularly during late adolescence and young adulthood. During an analysis, it is important to recognize all the determinants of idealization, including those related to the reworking of developmental conflicts. If an analyst understands idealization solely as a manifestation of pathology, he may interfere with his patient's use of it for the development of autonomous functioning.

  11. UV-light-induced one-color and two-color photorefractive effects in congruent and near-stoichiometric LiNbO 3:Mg crystals

    NASA Astrophysics Data System (ADS)

    Qiao, Haijun; Xu, Jingjun; Tomita, Yasuo; Zhu, Dengsong; Fu, Bo; Zhang, Guoquan; Zhang, Guangyin

    2007-03-01

    We describe the ultraviolet-light one-color photorefraction (UV-OPR) at 351 nm in LiNbO3 crystals with different Mg-doping concentrations and [Li]/[Nb] ratios. It is shown that as the Mg-doping concentration and/or the [Li]/[Nb] ratio increase, the refractive index change and the two-beam coupling gain increase but the response time decreases. It is also shown that the recording sensitivity as large as ∼27 cm/J is obtainable at a recording intensity of ∼1 W/cm2 in near-stoichiometric LiNbO3 doped with 2 mol% Mg. This sensitivity is approximately one order of magnitude higher than those for other LiNbO3 crystals. We also describe the ultraviolet-light-gating two-color photorefraction (UV-TPR) using 365 nm gating and 633 nm recording beams in LiNbO3 crystals with different Mg-doping concentrations and [Li]/[Nb] ratios. It is shown that UV-TPR is only observed in near-stoichiometric crystals and the grating-formation dynamics strongly depend on the Mg concentration.

  12. Quantification of processing artifacts in textile composites

    NASA Technical Reports Server (NTRS)

    Pastore, Christopher M.

    1993-01-01

    One of the greatest difficulties in developing detailed models of the mechanical response of textile reinforced composites is an accurate model of the reinforcing elements. In the case of elastic property prediction, the variation of fiber position may not have a critical role in performance. However, when considering highly localized stress events, such as those associated with cracks and holes, the exact position of the reinforcement probably dominates the failure mode. Models were developed for idealized reinforcements which provide an insight into the local behavior. However, even casual observations of micrographical images reveals that the actual material deviates strongly from the idealized models. Some of the deviations and causes are presented for triaxially braided and three dimensionally woven textile composites. The necessary modeling steps to accommodate these variations are presented with some examples. Some of the ramifications of not accounting for these discrepencies are also addressed.

  13. Moral identity as moral ideal self: links to adolescent outcomes.

    PubMed

    Hardy, Sam A; Walker, Lawrence J; Olsen, Joseph A; Woodbury, Ryan D; Hickman, Jacob R

    2014-01-01

    The purposes of this study were to conceptualize moral identity as moral ideal self, to develop a measure of this construct, to test for age and gender differences, to examine links between moral ideal self and adolescent outcomes, and to assess purpose and social responsibility as mediators of the relations between moral ideal self and outcomes. Data came from a local school sample (Data Set 1: N = 510 adolescents; 10-18 years of age) and a national online sample (Data Set 2: N = 383 adolescents; 15-18 years of age) of adolescents and their parents. All outcome measures were parent-report (Data Set 1: altruism, moral personality, aggression, and cheating; Data Set 2: environmentalism, school engagement, internalizing, and externalizing), whereas other variables were adolescent-report. The 20-item Moral Ideal Self Scale showed good reliability, factor structure, and validity. Structural equation models demonstrated that, even after accounting for moral identity internalization, in Data Set 1 moral ideal self positively predicted altruism and moral personality and negatively predicted aggression, whereas in Data Set 2 moral ideal self positively predicted environmentalism and negatively predicted internalizing and externalizing symptoms. Further, purpose and social responsibility mediated most relations between moral ideal self and the outcomes in Data Set 2. Moral ideal self was unrelated to age but differentially predicted some outcomes across age. Girls had higher levels of moral ideal self than boys, although moral identity did not differentially predict outcomes between genders. Thus, moral ideal self is a salient element of moral identity and may play a role in morally relevant adolescent outcomes. PsycINFO Database Record (c) 2014 APA, all rights reserved.

  14. Process for making a titanium diboride-chromium diboride-yttrium titanium oxide ceramic composition

    DOEpatents

    Holcombe, Cressie E.; Dykes, Norman L.

    1992-01-01

    A ceramic composition composition is described. The ceramic composition consists essentially of from about 84 to 96 w/o titanium diboride, from about 1 to 9 w/o chromium diboride, and from about 3 to aobut 15 w/o yttrium-titanium-oxide. A method of making the ceramic composition is also described. The method of making the ceramic composition comprises the following steps: Step 1--A consolidated body containing stoichiometric quantities of titanium diboride and chromium diboride is provided. Step 2--The consolidated body is enclosed in and in contact with a thermally insulated package of yttria granules having a thickness of at least 0.5 inches. Step 3--The consolidated body enclosed in the thermally insulated package of yttria granules is heated in a microwave oven with microwave energy to a temperature equal to or greater than 1,900 degrees centigrade to sinter and uniformly disperse yttria particles having a size range from about 1 to about 12 microns throughout the consolidated body forming a densified body consisting essentially of titanium diboride, chromium diboride, and yttrium-titanium-oxide. The resulting densified body has enhanced fracture toughness and hardness.

  15. Low Temperature Creep of Hot-Extruded Near-Stoichiometric NiTi Shape Memory Alloy. Part I; Isothermal Creep

    NASA Technical Reports Server (NTRS)

    Raj, S. V.; Noebe, R. D.

    2013-01-01

    This two-part paper is the first published report on the long term, low temperature creep of hot-extruded near-stoichiometric NiTi. Constant load tensile creep tests were conducted on hot-extruded near-stoichiometric NiTi at 300, 373 and 473 K under initial applied stresses varying between 200 and 350 MPa as long as 15 months. These temperatures corresponded to the martensitic, two-phase and austenitic phase regions, respectively. Normal primary creep lasting several months was observed under all conditions indicating dislocation activity. Although steady-state creep was not observed under these conditions, the estimated creep rates varied between 10(exp -10) and 10(exp -9)/s. The creep behavior of the two phases showed significant differences. The martensitic phase exhibited a large strain on loading followed by a primary creep region accumulating a small amount of strain over a period of several months. The loading strain was attributed to the detwinning of the martensitic phase whereas the subsequent strain accumulation was attributed to dislocation glide-controlled creep. An "incubation period" was observed before the occurrence of detwinning. In contrast, the austenitic phase exhibited a relatively smaller loading strain followed by a primary creep region, where the creep strain continued to increase over several months. It is concluded that the creep of the austenitic phase occurs by a dislocation glide-controlled creep mechanism as well as by the nucleation and growth of deformation twins.

  16. [Challenges and risks in the development of the ego ideal in adolescence].

    PubMed

    Helbing-Tietze, Brigitte

    2003-11-01

    The author proposes to speak of representations concerning the ideal self, the ideal relationship, the ideal society instead of ego ideal. An active self develops ideals and uses them as standards for orientation, to regulate the affects, and to fulfill needs. The different ideals often do not fit together and are therefore difficult to realize. Adolescents normally refuse their parents' ideals and create new ones with the help of their peers. This developmental step is full of challenges and risks as will be explained in this article.

  17. EPR of Nd3+ in congruent and nearly stoichiometric lithium niobate

    NASA Astrophysics Data System (ADS)

    Malovichko, G.; Grachev, V.; Okulov, S.; Kokanyan, E.; Henecker, F.; Hofstaetter, A.; Schirmer, O.

    2006-02-01

    The cover picture refers to the article by Galina Malovichko et al. which has been selected as Editor's Choice for this issue [1]. The lower part of the figure shows a section of the angular dependence of the EPR spectra in the xy-plane for nearly stoichiometric LiNbO3:Nd3+. The solid lines correspond to non-magnetic neodymium isotopes of axial C3 symmetry (green) and low C1 symmetry (purple and blue), respectively; the symbols represent experimental data. The upper part of the figure shows possible structures of the nearest surrounding for the C3 and C1 centers and their correspondence to the observed line positions.The first author Galina Malovichko is Associate Professor in the Physics Department at the Montana State University, USA. Her scientific activity is devoted to experimental condensed matter physics, particularly to the study of structures of extrinsic, intrinsic and radiation defects and their influence on crystal prop-erties. Her group is involved in the characterization of various materials and optimization of their parameters for advanced ap-plications.

  18. Enrichment in a stoichiometric model of two producers and one consumer.

    PubMed

    Lin, Laurence Hao-Ran; Peckham, Bruce B; Stech, Harlan W; Pastor, John

    2012-01-01

    We consider a stoichiometric population model of two producers and one consumer. Stoichiometry can be thought of as the tracking of food quality in addition to food quantity. Our model assumes a reduced rate of conversion of biomass from producer to consumer when food quality is low. The model is open for carbon but closed for nutrient. The introduction of the second producer, which competes with the first, leads to new equilibria, new limit cycles, and new bifurcations. The focus of this paper is on the bifurcations which are the result of enrichment. The primary parameters we vary are the growth rates of both producers. Secondary variable parameters are the total nutrients in the system, and the producer nutrient uptake rates. The possible equilibria are: no-life, one-producer, coexistence of both producers, the consumer coexisting with either producer, and the consumer coexisting with both producers. We observe limit cycles in the latter three coexistence combinations. Bifurcation diagrams along with corresponding representative time series summarize the behaviours observed for this model.

  19. Characterization of stoichiometric nanocrystalline spinel ferrites dispersed on porous silica aerogel.

    PubMed

    Casula, M F; Concas, G; Congiu, F; Corrias, A; Loche, D; Marras, C; Spano, G

    2011-11-01

    Stoichiometric magnetic nanosized ferrites MFe2O4 (M = Mn, Co, Ni) were prepared in form of nearly spherical nanocrystals supported on a highly porous silica aerogel matrix, by a sol-gel procedure. X-ray diffraction and transmission electron microscopy indicate that these materials are made out of non-agglomerated ferrite nanocrystals having size in the 5-10 nm range. Investigation by Mössbauer Spectroscopy was used to gain insights on the superparamagnetic relaxation and on the inversion degree. Magnetic ordering at room temperature varies from superparamagnetic in the NiFe2O4 sample, highly blocked (approximately 70%) in the MnFe2O4 sample and nearly fully blocked in the CoFe2O4 sample. A fitting procedure of the Mössbauer data has been used in order to resolve the spectrum into the tetrahedral and octahedral components; in this way, an inversion degree of 0.68 (very close to bulk values) was obtained for 6 nm silica-supported CoFe2O4 nanocrystals.

  20. The Tlo Proteins Are Stoichiometric Components of Candida albicans Mediator Anchored via the Med3 Subunit

    PubMed Central

    Zhang, Anda; Petrov, Kostadin O.; Hyun, Emily R.; Liu, Zhongle; Gerber, Scott A.

    2012-01-01

    The amplification of the TLO (for telomere-associated) genes in Candida albicans, compared to its less pathogenic, close relative Candida dubliniensis, suggests a role in virulence. Little, however, is known about the function of the Tlo proteins. We have purified the Mediator coactivator complex from C. albicans (caMediator) and found that Tlo proteins are a stoichiometric component of caMediator. Many members of the Tlo family are expressed, and each is a unique member of caMediator. Protein expression analysis of individual Tlo proteins, as well as the purification of tagged Tlo proteins, demonstrate that there is a large free population of Tlo proteins in addition to the Mediator-associated population. Coexpression and copurification of Tloα12 and caMed3 in Escherichia coli established a direct physical interaction between the two proteins. We have also made a C. albicans med3Δ/Δ strain and purified an intact Mediator from this strain. The analysis of the composition of the med3Δ Mediator shows that it lacks a Tlo subunit. Regarding Mediator function, the med3Δ/Δ strain serves as a substitute for the difficult-to-make tloΔ/Δ C. albicans strain. A potential role of the TLO and MED3 genes in virulence is supported by the inability of the med3Δ/Δ strain to form normal germ tubes. This study of caMediator structure provides initial clues to the mechanism of action of the Tlo genes and a platform for further mechanistic studies of caMediator's involvement in gene regulatory patterns that underlie pathogenesis. PMID:22562472

  1. Microstructure and hydrogenation properties of a melt-spun non-stoichiometric Zr-based Laves phase alloy

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Zhang, Tiebang, E-mail: tiebangzhang@nwpu.edu.cn; Zhang, Yunlong; Li, Jinshan

    2016-01-15

    Alloy with composition of Zr{sub 0.9}Ti{sub 0.1}V{sub 1.7} off normal stoichiometric proportion is selected to investigate the effect of defects introduced by non-stoichiometry on hydrogenation kinetics of Zr–Ti–V Laves phase alloys. Microstructure and phase constituent of melt-spun ribbons have been investigated in this work. The activation process, hydrogenation kinetics, thermodynamics characteristics and hydride phase constituent of as-cast alloy and melt-spun ribbons are also compared. Comparing with the as-cast alloy, the dominant Laves phase ZrV{sub 2} is preserved, V-BCC phase is reduced and α-Zr phase is replaced by a small amount of Zr{sub 3}V{sub 3}O phase in melt-spun ribbons. Melt-spun ribbonsmore » exhibit easy activation and fast initial hydrogen absorption on account of the increased specific surface area. However, the decrease in unit cell volume of the dominant phase leads to the decrease in hydrogen absorption capacity. Melt-spinning technique raises the equilibrium pressure and decreases the stability of hydride due to the decrease of unit cell volume and the elimination of α-Zr phase, respectively. Melt-spun ribbons with fine grains show improved hydrogen absorption kinetics comparing with that of the as-cast alloy. Meanwhile, the prevalent micro twins observed within melt-spun ribbons are believed to account for the improved hydrogen absorption kinetics. - Highlights: • Role of defects on hydrogenation kinetics of Zr-based alloys is proposed. • Microstructure and hydrogenation properties of as-cast/melt-spun alloy are compared. • Melt-spinning technique improves the hydrogenation kinetics of Zr{sub 0.9}Ti{sub 0.1}V{sub 1.7} alloy. • Refined grains and twin defects account for improved hydrogen absorption kinetics.« less

  2. The ideal subject distance for passport pictures.

    PubMed

    Verhoff, Marcel A; Witzel, Carsten; Kreutz, Kerstin; Ramsthaler, Frank

    2008-07-04

    In an age of global combat against terrorism, the recognition and identification of people on document images is of increasing significance. Experiments and calculations have shown that the camera-to-subject distance - not the focal length of the lens - can have a significant effect on facial proportions. Modern passport pictures should be able to function as a reference image for automatic and manual picture comparisons. This requires a defined subject distance. It is completely unclear which subject distance, in the taking of passport photographs, is ideal for the recognition of the actual person. We show here that the camera-to-subject distance that is perceived as ideal is dependent on the face being photographed, even if the distance of 2m was most frequently preferred. So far the problem of the ideal camera-to-subject distance for faces has only been approached through technical calculations. We have, for the first time, answered this question experimentally with a double-blind experiment. Even if there is apparently no ideal camera-to-subject distance valid for every face, 2m can be proposed as ideal for the taking of passport pictures. The first step would actually be the determination of a camera-to-subject distance for the taking of passport pictures within the standards. From an anthropological point of view it would be interesting to find out which facial features allow the preference of a shorter camera-to-subject distance and which allow the preference of a longer camera-to-subject distance.

  3. Compositional variation in minerals of the chevkinite group

    USGS Publications Warehouse

    Macdonald, R.; Belkin, H.E.

    2002-01-01

    The composition of chevkinite and perrierite, the most common members of the chevkinite group, is closely expressed by the formula A4BC2D2Si4O22, where A = (La,Ce,Ca,Sr,Th), B = Fe2+, C = (Fe2+,Fe3+,Ti,Al,Zr,Nb) and D = Ti. The A site is dominated by a strong negative correlation between (Ca+Sr) and the REE. Chondrite-normalized REE patterns are very variable, e.g. in LREE/HREE and Eu/Eu*. The C site is dominated by Ti, Al and Fe2+, in very variable proportions. Most chevkinites and perrierites are close to stoichiometric, with cation sums between 12.9 and 13.5, compared to the theoretical 13. There is no single, generally applicable charge balancing substitution scheme in the group; however, the general relationship (Ca+Sr)A + TiC + REEA + M3C+2+ defines a linear array with r2 = 0.91. Chevkinite and perrierite are shown to be compositionally distinct on the basis of CaO, FeO* Al2O3 and Ce2O3 abundances. Chevkinite forms mainly in chemically evolved parageneses, such as syenites, rhyolites and fenites associated with carbonatite complexes. Perrierite is more commonly recorded from igneous rocks of mafic to intermediate composition. The compositional characteristics and possible structural formulae of other members of the chevkinite group are reviewed briefly.

  4. Studies on the retention mechanism of solutes in hydrophilic interaction chromatography using stoichiometric displacement theory I. The linear relationship of lgk' vs. lg[H2O].

    PubMed

    Wang, Fei; Yang, Fan; Tian, Yang; Liu, Jiawei; Shen, Jiwei; Bai, Quan

    2018-01-01

    A stoichiometric displacement model for retention (SDM-R) of small solutes and proteins based on hydrophilic interaction chromatography (HILIC) was presented. A linear equation that related the logarithm of the capacity factor of the solute to the logarithm of the concentration of water in the mobile phase was derived. The stoichiometric displacement parameters, Z (the number of water molecules required to displace a solute from ligands) and lgI (containing a number of constants that relate to the affinity of solute to the ligands) could be obtained from the slope and the intercept of the linear plots of lgk' vs. lg[H 2 O]. The retention behaviors and retention mechanism of 15 kinds of small solutes and 6 kinds of proteins on 5 kinds HILIC columns with different ligands were investigated with SDM-R in typical range of water concentration in mobile phase. A good linear relationship between lgk' and lg[H 2 O] demonstrated that the most rational retention mechanism of solute in HILIC was a stoichiometric displacement process between solute and solvent molecules with water as displacing agents, which was not only valid for small solutes, but also could be used to explain the retention mechanism of biopolymers in HILIC. Comparing with the partition and adsorption models in HILIC, SDM-R was superior to them. Copyright © 2017 Elsevier B.V. All rights reserved.

  5. Preparation of porous PLA/DBM composite biomaterials and experimental research of repair rabbit radius segmental bone defect.

    PubMed

    Zhang, Yumin; Wang, Jianru; Wang, Jue; Niu, Xiaojun; Liu, Jianchun; Gao, Lan; Zhai, Xiaoyan; Chu, Kaibo

    2015-12-01

    Bone substitutes are used in wide range of orthopaedic application. An ideal bone substitute should exhibit superior osteoinductive and osteoconductive properties. Neither bio-derived materials nor synthetic materials can meet the needs of an ideal bone substitute. Preparation of composite materials is a promising way to improve properties of biomaterial. In this study, the porous poly lactic acid (PLA)/demineralized bone matrix (DBM) composite biomaterials prepared by supercritical CO2 technique were implanted to repair rabbit radius segmental bone defect. By comparing with PLA and bone autograft, the X-ray result and histological analysis showed the repair effect of PLA/DBM porous composite materials is significantly better than that of the PLA group and the blank control group, and is similar to autologous bone. The PLA/DBM can promote the healing of bone defects and can be used as a kind of ideal alternative materials to repair bone defects.

  6. Investigation on LiBH4-CaH2 composite and its potential for thermal energy storage.

    PubMed

    Li, Yang; Li, Ping; Qu, Xuanhui

    2017-01-31

    The LiBH 4 /CaH 2 composite are firstly studied as Concentrating Solar Power Thermal Storage Material. The LiBH 4 /CaH 2 composite according to the stoichiometric ratio are synthesized by high-energy ball milling method. The kinetics, thermodynamics and cycling stability of LiBH 4 /CaH 2 composite are investigated by XRD (X-ray diffraction), DSC (Differential scanning calorimeter) and TEM (Transmission electron microscope). The reaction enthalpy of LiBH 4 /CaH 2 composite is almost 60 kJ/mol H 2 and equilibrium pressure is 0.482 MPa at 450 °C. The thermal storage density of LiBH 4 /CaH 2 composite is 3504.6 kJ/kg. XRD results show that the main phase after dehydrogenation is LiH and CaB 6 . The existence of TiCl 3 and NbF 5 can effectively enhance the cycling perfomance of LiBH 4 /CaH 2 composite, with 6-7 wt% hydrogen capacity after 10 cycles. The high thermal storage density, high working temperature and low equilibrium pressure make LiBH 4 /CaH 2 composite a potential thermal storage material.

  7. Spaces of ideal convergent sequences.

    PubMed

    Mursaleen, M; Sharma, Sunil K

    2014-01-01

    In the present paper, we introduce some sequence spaces using ideal convergence and Musielak-Orlicz function ℳ = (M(k)). We also examine some topological properties of the resulting sequence spaces.

  8. Effect of solution non-ideality on erythrocyte volume regulation.

    PubMed

    Levin, R L; Cravalho, E G; Huggins, C E

    1977-03-01

    A non-ideal, hydrated, non-dilute pseudo-binary salt-protein-water solution model of the erythrocyte intracellular solution is presented to describe the osmotic behavior of human erythrocytes. Existing experimental activity data for salts and proteins in aqueous solutions are used to formulate van Laar type expressions for the solvent and solute activity coefficients. Reasonable estimates can therefore be made of the non-ideality of the erythrocyte intracellular solution over a wide range of osmolalities. Solution non-ideality is shown to affect significantly the degree of solute polarization within the erythrocyte intracellular solution during freezing. However, the non-ideality has very little effect upon the amount of water retained within erythrocytes cooled at sub-zero temperatures.

  9. Molecular dynamics simulation of premelting and melting phase transitions in stoichiometric uranium dioxide

    NASA Astrophysics Data System (ADS)

    Yakub, Eugene; Ronchi, Claudio; Staicu, Dragos

    2007-09-01

    Results of molecular dynamics (MD) simulation of UO2 in a wide temperature range are presented and discussed. A new approach to the calibration of a partly ionic Busing-Ida-type model is proposed. A potential parameter set is obtained reproducing the experimental density of solid UO2 in a wide range of temperatures. A conventional simulation of the high-temperature stoichiometric UO2 on large MD cells, based on a novel fast method of computation of Coulomb forces, reveals characteristic features of a premelting λ transition at a temperature near to that experimentally observed (Tλ=2670K ). A strong deviation from the Arrhenius behavior of the oxygen self-diffusion coefficient was found in the vicinity of the transition point. Predictions for liquid UO2, based on the same potential parameter set, are in good agreement with existing experimental data and theoretical calculations.

  10. Theory of simultaneous excitonic-superconductivity condensation II Experimental evidence and stoichiometric interpretations

    NASA Astrophysics Data System (ADS)

    Wong, K. W.; Ching, W. Y.

    1989-04-01

    We discuss a variety of experimental observations which are consistent with theory of the excitonic-enhancement model (EEM) presented earlier. The experimental works discussed are: (1) isotope substitution; (2) fluorinated YBa 2Cu 3O 7- x; (3) infrared optical spectra; (4) specific heat and tunneling gap; (5) Hall effect and nuclear spin relaxation; (6) positron annihilation; (7) utrasound velocity and sound attenuation; (8) Meissner effect and critical current; (9) antiferromagnetism and oxygen deficiency; (10) flux quantization; and (11) photoemission. A simple stoichiometric interpretation on the existing high temperature superconducting oxides based on the specific stacking of chemical subsystems is also presented. It is argued that according to EEM theory, a superconducting oxide must contain two stable oxides, one having excitonic levels such as Cu 2O; the other having intrinsic hole population at the top of the valence band such as CuO. A systematic search for other potential high Tc compounds is also suggested.

  11. Media-portrayed idealized images, body shame, and appearance anxiety.

    PubMed

    Monro, Fiona; Huon, Gail

    2005-07-01

    This study was designed to determine the effects of media-portrayed idealized images on young women's body shame and appearance anxiety, and to establish whether the effects depend on advertisement type and on participant self-objectification. Participants were 39 female university students. Twenty-four magazine advertisements comprised 12 body-related and 12 non-body-related products, one half of each with, and the other one half without, idealized images. Preexposure and post exposure body shame and appearance anxiety measures were recorded. Appearance anxiety increased after viewing advertisements featuring idealized images. There was also a significant interaction between self-objectification level and idealized body (presence vs. absence). No differences emerged for body-related compared with non-body-related product advertisements. The only result for body shame was a main effect for time. Participants' body shame increased after exposure to idealized images, irrespective of advertisement type. Although our findings reveal that media-portrayed idealized images detrimentally affect the body image of young women, they highlight the individual differences in vulnerability and the different effects for different components of body image. These results are discussed in terms of their implications for the prevention and early intervention of body image and dieting-related disorders. ( Copyright 2005 by Wiley Periodicals, Inc

  12. Coupling Ideality of Integrated Planar High-Q Microresonators

    NASA Astrophysics Data System (ADS)

    Pfeiffer, Martin H. P.; Liu, Junqiu; Geiselmann, Michael; Kippenberg, Tobias J.

    2017-02-01

    Chip-scale optical microresonators with integrated planar optical waveguides are useful building blocks for linear, nonlinear, and quantum-optical photonic devices alike. Loss reduction through improving fabrication processes results in several integrated microresonator platforms attaining quality (Q ) factors of several millions. Beyond the improvement of the quality factor, the ability to operate the microresonator with high coupling ideality in the overcoupled regime is of central importance. In this regime, the dominant source of loss constitutes the coupling to a single desired output channel, which is particularly important not only for quantum-optical applications such as the generation of squeezed light and correlated photon pairs but also for linear and nonlinear photonics. However, to date, the coupling ideality in integrated photonic microresonators is not well understood, in particular, design-dependent losses and their impact on the regime of high ideality. Here we investigate design-dependent parasitic losses described by the coupling ideality of the commonly employed microresonator design consisting of a microring-resonator waveguide side coupled to a straight bus waveguide, a system which is not properly described by the conventional input-output theory of open systems due to the presence of higher-order modes. By systematic characterization of multimode high-Q silicon nitride microresonator devices, we show that this design can suffer from low coupling ideality. By performing 3D simulations, we identify the coupling to higher-order bus waveguide modes as the dominant origin of parasitic losses which lead to the low coupling ideality. Using suitably designed bus waveguides, parasitic losses are mitigated with a nearly unity ideality and strong overcoupling (i.e., a ratio of external coupling to internal resonator loss rate >9 ) are demonstrated. Moreover, we find that different resonator modes can exchange power through the coupler, which, therefore

  13. Controlling the sol–gel process of nano-crystalline lithium-mica glass-ceramic by its chemical composition and synthesis parameters

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Tohidifar, M.R., E-mail: tohidifar@znu.ac.ir; Alizadeh, P.; Aghaei, A.R.

    2015-01-15

    This paper aims to explore the impact of the parameters such as pH of the system, refluxing temperature, water quantity and chemical composition on the sol–gel synthesis of lithium-mica glass-ceramic nano-powder. The synthesis process was accomplished using two chemical composition formula (Li{sub (1+x)}Mg{sub 3}AlSi{sub 3(1+x)}O{sub 10+6.5x}F{sub 2} and LiMg{sub 3}AlSi{sub 3(1+x)}O{sub 10+6x}F{sub 2}). X-ray diffraction, Brunauer–Emmett–Teller surface area measurement and scanning electron microscopy techniques were applied to evaluate a variety of as-synthesized samples. Consequently, a transparent homogeneous sol was obtained under the conditions as pH ≤ 4, synthesis temperature ≤ 50 °C, and mol ratio of water to chemicals ≤more » 2. The prepared nano-powders under such conditions were in the range of 60–100 nm. The results also revealed that the mica glass-ceramics prepared based on the composition Li{sub (1+x)}Mg{sub 3}AlSi{sub 3(1+x)}O{sub 10+6.5x}F{sub 2} possessed finer powders due to their slow hydrolysis process. Moreover, any reduction in the stoichiometric deviation of lithium mica (x) leads to acquiring finer powders. - Highlights: • A transparent homogeneous sol leads to prepare nanopowders in the range of 60–100 nm. • The particles synthesized at lower temperatures possess finer sizes. • The acquired product which is prepared with excessive water offers larger sizes. • Any reduction in stoichiometric deviation leads to acquiring finer powders. • Taking synthesis composition as Li{sub (1+x)}Mg{sub 3}AlSi{sub 3(1+x)}O{sub 10+6.5x}F{sub 2} offers finer powders.« less

  14. Non-ideal magnetohydrodynamics on a moving mesh

    NASA Astrophysics Data System (ADS)

    Marinacci, Federico; Vogelsberger, Mark; Kannan, Rahul; Mocz, Philip; Pakmor, Rüdiger; Springel, Volker

    2018-05-01

    In certain astrophysical systems, the commonly employed ideal magnetohydrodynamics (MHD) approximation breaks down. Here, we introduce novel explicit and implicit numerical schemes of ohmic resistivity terms in the moving-mesh code AREPO. We include these non-ideal terms for two MHD techniques: the Powell 8-wave formalism and a constrained transport scheme, which evolves the cell-centred magnetic vector potential. We test our implementation against problems of increasing complexity, such as one- and two-dimensional diffusion problems, and the evolution of progressive and stationary Alfvén waves. On these test problems, our implementation recovers the analytic solutions to second-order accuracy. As first applications, we investigate the tearing instability in magnetized plasmas and the gravitational collapse of a rotating magnetized gas cloud. In both systems, resistivity plays a key role. In the former case, it allows for the development of the tearing instability through reconnection of the magnetic field lines. In the latter, the adopted (constant) value of ohmic resistivity has an impact on both the gas distribution around the emerging protostar and the mass loading of magnetically driven outflows. Our new non-ideal MHD implementation opens up the possibility to study magneto-hydrodynamical systems on a moving mesh beyond the ideal MHD approximation.

  15. Compositional inhomogeneities in AlGaN thin films grown by molecular beam epitaxy: Effect on MSM UV photodetectors

    NASA Astrophysics Data System (ADS)

    Pramanik, Pallabi; Sen, Sayantani; Singha, Chirantan; Roy, Abhra Shankar; Das, Alakananda; Sen, Susanta; Bhattacharyya, A.

    2016-10-01

    Ultraviolet (UV) MSM photodetectors (PD) based on AlGaN alloys find many applications, including flame sensing. In this work we investigate the dependence of AlGaN based photodetectors grown by MBE on the kinetics of growth. MSM photodetectors were fabricated in the interdigitated configuration with Ni/Au contacts having 400 μm finger length and 10 μm finger spacing. Bulk Al0.4Ga0.6N films were grown on to sapphire substrates using an AlN buffer layer. A series of PDs were developed using the Al0.4Ga0.6N films grown under different group III/V flux ratios ranging from stoichiometric conditions to much higher than unity. Upon testing, it was observed that the otherwise identical photodetectors show significant decrease in dark current as AlGaN deposition conditions change from stoichiometric to excess group III, due to reduction of unintentional incorporation of oxygen-related point defects. In addition, the intensity and spectral dependence of the photocurrent also change, showing an extended low energy tail for the former and a sharp and prominent excitonic peak for the latter. The optical transmission measurements indicate a variation in Urbach energy with deposition conditions of the AlGaN films, although they have the same absorption edge. While all samples show a single red-shifted photoluminescence peak at room temperature, upon cooling, multiple higher energy peaks appear in the photoluminescence (PL) spectra, indicating that the alloys contain complex compositional inhomogeneities. Two types of alloy fluctuations, determined by the growth conditions, have been identified that modulate the optoelectronic properties of AlGaN by changing the spatial localization of excitons, thereby altering their stability. We identified that growth under stoichiometric conditions leads to compositional inhomogeneities that play a detrimental role in the operation of MSM photodetectors, which reduces the sharpness of the sensitivity edge, while growth under excess metal

  16. Sharp Truncation of an Electric Field: An Idealized Model that Warrants Caution

    NASA Astrophysics Data System (ADS)

    Tu, Hong; Zhu, Jiongming

    2016-03-01

    In physics, idealized models are often used to simplify complex situations. The motivation of the idealization is to make the real complex system tractable by adopting certain simplifications. In this treatment some unnecessary, negligible aspects are stripped away (so-called Aristotelian idealization), or some deliberate distortions are involved (so-called Galilean idealization). The most important principle in using an idealized model is to make sure that all the neglected aspects do not affect our analysis or result. Point charges, rigid bodies, simple pendulums, frictionless planes, and isolated systems are all frequently used idealized models. However, when they are applied to certain uncommon models, extra precautions should be taken. The possibilities and necessities of adopting the idealizations have to be considered carefully. Sometimes some factors neglected or ignored in the idealization could completely change the result, even make the treatment unphysical and conclusions unscientific.

  17. Box-modeling of bone and tooth phosphate oxygen isotope compositions as a function of environmental and physiological parameters.

    PubMed

    Langlois, C; Simon, L; Lécuyer, Ch

    2003-12-01

    A time-dependent box model is developed to calculate oxygen isotope compositions of bone phosphate as a function of environmental and physiological parameters. Input and output oxygen fluxes related to body water and bone reservoirs are scaled to the body mass. The oxygen fluxes are evaluated by stoichiometric scaling to the calcium accretion and resorption rates, assuming a pure hydroxylapatite composition for the bone and tooth mineral. The model shows how the diet composition, body mass, ambient relative humidity and temperature may control the oxygen isotope composition of bone phosphate. The model also computes how bones and teeth record short-term variations in relative humidity, air temperature and delta18O of drinking water, depending on body mass. The documented diversity of oxygen isotope fractionation equations for vertebrates is accounted for by our model when for each specimen the physiological and diet parameters are adjusted in the living range of environmental conditions.

  18. Ideal thermodynamic processes of oscillatory-flow regenerative engines will go to ideal stirling cycle?

    NASA Astrophysics Data System (ADS)

    Luo, Ercang

    2012-06-01

    This paper analyzes the thermodynamic cycle of oscillating-flow regenerative machines. Unlike the classical analysis of thermodynamic textbooks, the assumptions for pistons' movement limitations are not needed and only ideal flowing and heat transfer should be maintained in our present analysis. Under such simple assumptions, the meso-scale thermodynamic cycles of each gas parcel in typical locations of a regenerator are analyzed. It is observed that the gas parcels in the regenerator undergo Lorentz cycle in different temperature levels, whereas the locus of all gas parcels inside the regenerator is the Ericson-like thermodynamic cycle. Based on this new finding, the author argued that ideal oscillating-flow machines without heat transfer and flowing losses is not the Stirling cycle. However, this new thermodynamic cycle can still achieve the same efficiency of the Carnot heat engine and can be considered a new reversible thermodynamic cycle under two constant-temperature heat sinks.

  19. Moral Identity as Moral Ideal Self: Links to Adolescent Outcomes

    ERIC Educational Resources Information Center

    Hardy, Sam A.; Walker, Lawrence J.; Olsen, Joseph A.; Woodbury, Ryan D.; Hickman, Jacob R.

    2014-01-01

    The purposes of this study were to conceptualize moral identity as moral ideal self, to develop a measure of this construct, to test for age and gender differences, to examine links between moral ideal self and adolescent outcomes, and to assess purpose and social responsibility as mediators of the relations between moral ideal self and outcomes.…

  20. Cavity-dumped femtosecond optical parametric oscillator based on periodically poled stoichiometric lithium tantalate

    NASA Astrophysics Data System (ADS)

    Yoon, E.; Joo, T.

    2016-03-01

    A synchronously pumped cavity-dumped femtosecond optical parametric oscillator (OPO) based on a periodically poled stoichiometric lithium tantalate (PPSLT) crystal is reported. The OPO runs in positive group velocity dispersion (GVD) mode to deliver high pulse energy at high repetition rate. It delivers pulse energy over 130 nJ up to 500 kHz and 70 nJ at 1 MHz of repetition rate at 1100 nm. Pulse duration is as short as 42 fs, and the OPO is tunable in the near infrared region from 1050 to 1200 nm. Dispersion property of the OPO was also explored. The cavity-dumped output carries a positive GVD, which can be compensated easily by an external prism pair, and large negative third order dispersion (TOD), which results in a pedestal in the pulse shape. Approaches to obtain clean pulse shape by reducing the large TOD are proposed.

  1. Gapless quantum excitations from an icelike splayed ferromagnetic ground state in stoichiometric Yb 2 Ti 2 O 7

    DOE PAGES

    Gaudet, J.; Ross, K. A.; Kermarrec, E.; ...

    2016-02-03

    We know the ground state of the quantum spin ice candidate magnet Yb 2Ti 2O 7 to be sensitive to weak disorder at the similar to 1% level which occurs in single crystals grown from the melt. Powders produced by solid state synthesis tend to be stoichiometric and display large and sharp heat capacity anomalies at relatively high temperatures, T-C similar to 0.26 K. We have carried out neutron elastic and inelastic measurements on well characterized and equilibrated stoichiometric powder samples of Yb 2Ti 2O 7 which show resolution-limited Bragg peaks to appear at low temperatures, but whose onset correlatesmore » with temperatures much higher than T-C. The corresponding magnetic structure is best described as an icelike splayed ferromagnet. In the spin dynamics of Yb 2Ti 2O 7 we see the gapless on an energy scale <0.09 meV at all temperatures and organized into a continuum of scattering with vestiges of highly overdamped ferromagnetic spin waves present. These excitations differ greatly from conventional spin waves predicted for Yb 2Ti 2O 7's mean field ordered state, but appear robust to weak disorder as they are largely consistent with those displayed by nonstoichiometric crushed single crystals and single crystals, as well as by powder samples of Yb 2Ti 2O 7's sister quantum magnet Yb 2Ti 2O 7.« less

  2. A reactive flow model with coupled reaction kinetics for detonation and combustion in non-ideal explosives

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Miller, P.J.

    1996-07-01

    A new reactive flow model for highly non-ideal explosives and propellants is presented. These compositions, which contain large amounts of metal, upon explosion have reaction kinetics that are characteristic of both fast detonation and slow metal combustion chemistry. A reaction model for these systems was incorporated into the two-dimensional, finite element, Lagrangian hydrodynamic code, DYNA2D. A description of how to determine the model parameters is given. The use of the model and variations are applied to AP, Al, and nitramine underwater explosive and propellant systems.

  3. Soil nutrients and stoichiometric ratios as affected by land use and lithology at county scale in a karst area, southwest China.

    PubMed

    Wang, Miaomiao; Chen, Hongsong; Zhang, Wei; Wang, Kelin

    2018-04-01

    Soil carbon (C), nitrogen (N), and phosphorus (P) are the main soil nutrients required for plant development and their stoichiometric ratios are important indicators of ecosystem functions. However, there have been few studies on the effects of land use and lithology on soil nutrients and stoichiometric ratios, especially in karst areas with extremely fragile geology and intensive human disturbance. To evaluate the synergistic effect of land use and lithology, soil samples at depth of 0-15cm were collected from five land-use types (arable land, plantation forest, grassland, shrubland, and secondary forest) over three lithologies (karst dolomite and limestone and non-karst clasolite) in a typical karst area in southwest China. For natural succession, grassland, shrubland, and secondary forest corresponded to the early, middle, and late successional stage after agricultural abandonment, while from arable land to plantation forest can be treated as a manual reversion after agricultural abandonment. The results showed that, in dolomite, soil organic C (SOC) and total N (TN) increased continuously with natural succession and increased in plantation forest compared to arable land. Total P (TP) continued to decrease from arable land to grassland and then to shrubland. In limestone, SOC and TN did not follow the same pattern because SOC and TN were slightly higher in grassland than shrubland, while TN was slightly lower in plantation forest compared to arable land. TP was remarkably higher in arable land than the other land-use types. For clasolite, SOC was highest in grassland, while TN was not significantly different among land-use types. Compared to arable land, TP was lower in other types of land use. These soil nutrient characteristics led to various stoichiometric ratios under the five land-use types over different lithologies. Therefore, ecological restoration projects based on land use conversion should consider differences in regional lithology and human

  4. Jung's Red Book and its relation to aspects of German idealism.

    PubMed

    Bishop, Paul

    2012-06-01

    The late nineteenth century saw a renaissance of interest in the thought of the German Romantic philosopher, F.W.J. Schelling. This paper takes Jung's engagement with Schelling and his awareness of Schellingian ideas and interests (notably, the mysterious Kabeiroi worshipped at Samothrace) as its starting-point. It goes on to argue that a key set of problematics in German Idealism - the relation between freedom and necessity, between science and art, and ultimately between realism and idealism - offers a useful conceptual framework within which to approach Jung's Red Book. For the problem of the ideal is central to this work, which can be read as a journey from eternal ideals to the ideal of eternity. (Although the term 'idealism' has at least four distinct meanings, their distinct senses can be related in different ways to Jung's thinking.) The eloquent embrace of idealism by F.T. Vischer in a novel, Auch Einer, for which Jung had the highest praise, reminds us of the persistence of this tradition, which is still contested and debated in the present day. © 2012, The Society of Analytical Psychology.

  5. Synthesis and characterization of LPCVD SiC films using novel precursors

    NASA Astrophysics Data System (ADS)

    Bhaskaran, Mahalingam

    A unique low pressure chemical vapor deposition (LPCVD) process has been developed to synthesize amorphous and crystalline SiC films using environmentally benign chemicals. The interrelationships governing the process variables, compositions and select properties of the resulting films were established. Such films can be used to produce high quality mask membrane for x-ray lithography. These films can also be used in fabricating high power electrical devices, and hetrojunction devices in conjunction with silicon. Amorphous SiC films were synthesized using a single precursor, ditertiarybutylsilane, at temperatures below 850sp°C. Compositional analysis performed on these deposits revealed that, in the deposition temperature range of 625 to 750sp°C, the composition of the deposits changed progressively from slightly silicon rich (55% Si) to slightly carbon rich (51%C). Above 750sp°C, there was a rapid increase in the carbon content from the near stoichiometric value to about 75%-C at 850sp°C. The stoichiometric films exhibited high stress values of 700 ± 50 MPa. Attempts to reduce the stress values resulted in films with excess carbon content of about 60%-C. From the high frequency C-V characterization, the dielectric constant for these films was estimated to be 10.1 ± 0.5. Temperature bias stressing studies revealed a trapped charge density of 0.869× 10sp7 cIsp{-2} within the bulk. Crystalline silicon carbide films were grown on silicon substrates using dichlorosilane and acetylene as precursors, in the temperature range of 950sp°C to 1050sp°C. The carbon content in the film was found to be increasing with the deposition temperature, when the flow ratio of precursors was one. The carbon composition was also found to be sharply dependent on acetylene flow, for constant deposition temperature and pressure. Stoichiometric films were achieved for dichlorosilane to acetylene flow ratio of 4:1. X-ray diffraction studies confirmed the growth of beta-SiC with

  6. A Generalized Deduction of the Ideal-Solution Model

    ERIC Educational Resources Information Center

    Leo, Teresa J.; Perez-del-Notario, Pedro; Raso, Miguel A.

    2006-01-01

    A new general procedure for deriving the Gibbs energy of mixing is developed through general thermodynamic considerations, and the ideal-solution model is obtained as a special particular case of the general one. The deduction of the Gibbs energy of mixing for the ideal-solution model is a rational one and viewed suitable for advanced students who…

  7. Compositions of professionalism in counselling work: An embodied and embedded intersectionality framework.

    PubMed

    Adamson, Maria; Johansson, Marjana

    2016-12-01

    This article explores the embodied compositions of professionalism in the context of the counselling psychology profession in Russia. Specifically, we develop an embodied intersectionality framework for theorizing compositions of professionalism, which allows us to explain how multiple embodied categories of difference intersect and are relationally co-constitutive in producing credible professionals, and, importantly, how these intersections are contingent on intercorporeal encounters that take place in localized professional settings. Our exploration of how professionalism and professional credibility are established in Russian counselling shows that, rather than assuming that a hegemonic 'ideal body' is given preference in a professional context, different embodied compositions may be deemed credible in various work settings within the same profession. An embodied intersectionality framework allows us to challenge the notion of a single professional ideal and offer a dynamic and contextually situated analysis of the lived experiences of professional privilege and disadvantage.

  8. Compositions of professionalism in counselling work: An embodied and embedded intersectionality framework

    PubMed Central

    Adamson, Maria; Johansson, Marjana

    2016-01-01

    This article explores the embodied compositions of professionalism in the context of the counselling psychology profession in Russia. Specifically, we develop an embodied intersectionality framework for theorizing compositions of professionalism, which allows us to explain how multiple embodied categories of difference intersect and are relationally co-constitutive in producing credible professionals, and, importantly, how these intersections are contingent on intercorporeal encounters that take place in localized professional settings. Our exploration of how professionalism and professional credibility are established in Russian counselling shows that, rather than assuming that a hegemonic ‘ideal body’ is given preference in a professional context, different embodied compositions may be deemed credible in various work settings within the same profession. An embodied intersectionality framework allows us to challenge the notion of a single professional ideal and offer a dynamic and contextually situated analysis of the lived experiences of professional privilege and disadvantage. PMID:27904172

  9. Media-portrayed idealized images, self-objectification, and eating behavior.

    PubMed

    Monro, Fiona J; Huon, Gail F

    2006-11-01

    This study examined the effects of media-portrayed idealized images on young women's eating behavior. The study compared the effects for high and low self-objectifiers. 72 female university students participated in this experiment. Six magazine advertisements featuring idealized female models were used as the experimental stimuli, and the same six advertisements with the idealized body digitally removed became the control stimuli. Eating behavior was examined using a classic taste test that involved both sweet and savory food. Participants' restraint status was assessed. We found that total food intake after exposure was the same in the body present and absent conditions. There were also no differences between high and low self-objectifiers' total food intake. However, for the total amount of food consumed and for sweet food there were significant group by condition interaction effects. High self-objectifiers ate more food in the body present than the body absent condition. In contrast, low self-objectifiers ate more food in the body absent than in the body present condition. Restraint status was not found to moderate the relationship between exposure to idealized images the amount of food consumed. Our results indicate that exposure to media-portrayed idealized images can lead to changes in eating behavior and highlight the complexity of the association between idealized image exposure and eating behavior. These results are discussed in terms of their implications for the prevention of dieting-related disorders.

  10. Process for making a titanium diboride-chromium diboride-yttrium titanium oxide ceramic composition

    DOEpatents

    Holcombe, C.E.; Dykes, N.L.

    1992-04-28

    A ceramic composition is described. The ceramic composition consists essentially of from about 84 to 96 w/o titanium diboride, from about 1 to 9 w/o chromium diboride, and from about 3 to about 15 w/o yttrium-titanium-oxide. A method of making the ceramic composition is also described. The method of making the ceramic composition comprises the following steps: Step 1--A consolidated body containing stoichiometric quantities of titanium diboride and chromium diboride is provided. Step 2--The consolidated body is enclosed in and in contact with a thermally insulated package of yttria granules having a thickness of at least 0.5 inches. Step 3--The consolidated body enclosed in the thermally insulated package of yttria granules is heated in a microwave oven with microwave energy to a temperature equal to or greater than 1,900 degrees centigrade to sinter and uniformly disperse yttria particles having a size range from about 1 to about 12 microns throughout the consolidated body forming a densified body consisting essentially of titanium diboride, chromium diboride, and yttrium-titanium-oxide. The resulting densified body has enhanced fracture toughness and hardness. No Drawings

  11. Stoichiometric Correlation of Malate Accumulation with Auxin-dependent K+-H+ Exchange and Growth in Avena Coleoptile Segments 12

    PubMed Central

    Haschke, Hans-Peter; Lüttge, Ulrich

    1975-01-01

    The action of auxin in the promotion of growth has been suggested in the literature to depend on cell wall acidification. In a former investigation by the present authors the electrochemical balance in auxin-induced proton extrusion was shown to be maintained by potassium net uptake. The present paper reports data demonstrating that the elongation of Avena coleoptile segments is accompanied by an accumulation of malate, which is stoichiometrically correlated with potassium uptake. We concluded that this malate accumulation is required in a mechanism regulating intracellular pH. PMID:16659374

  12. Flexible n-type thermoelectric composite films with enhanced performance through interface engineering and post-treatment.

    PubMed

    An, Hyeunhwan; Karas, Dale; Kim, Byung-Wook; Trabia, Sarah; Moon, Jaeyun

    2018-07-06

    Flexible thermoelectric (TE) materials, which are devices that convert thermal gradients to electrical energy, have attracted interest for practical energy-harvesting/recovery applications. However, as compared with p-type materials, the progress on the development of n-type TE flexible materials has been slow due to difficulties involved in n-type doping techniques. This study used high mobility carbon nanotubes (CNTs) to a uniformly mixed hybrid-composite, resulting in an enhanced power factor by increasing electrical conductivity. The energy filtering effect and stoichiometric composition of the material used, bismuth telluride (Bi 2 Te 3 ) correlated to a significant enhancement in TE performance, with a power factor of 225.9 μW m -1 K -2 at room temperature: a factor of 65 higher than as-fabricated composite film. This paper describes a simplified synthesis for the preparation of the composite film that eliminates time-intensive and cost-prohibitive processing, traditionally seen during extrusion and dicing inorganic manufacturing. The resulting post-annealed composite film consisting of Bi 2 Te 3 nanowire and CNTs demonstrate a promising candidate for material that can be used for an n-type TE device that has improved energy conversion efficiency.

  13. Flexible n-type thermoelectric composite films with enhanced performance through interface engineering and post-treatment

    NASA Astrophysics Data System (ADS)

    An, Hyeunhwan; Karas, Dale; Kim, Byung-Wook; Trabia, Sarah; Moon, Jaeyun

    2018-07-01

    Flexible thermoelectric (TE) materials, which are devices that convert thermal gradients to electrical energy, have attracted interest for practical energy-harvesting/recovery applications. However, as compared with p-type materials, the progress on the development of n-type TE flexible materials has been slow due to difficulties involved in n-type doping techniques. This study used high mobility carbon nanotubes (CNTs) to a uniformly mixed hybrid-composite, resulting in an enhanced power factor by increasing electrical conductivity. The energy filtering effect and stoichiometric composition of the material used, bismuth telluride (Bi2Te3) correlated to a significant enhancement in TE performance, with a power factor of 225.9 μW m‑1K‑2 at room temperature: a factor of 65 higher than as-fabricated composite film. This paper describes a simplified synthesis for the preparation of the composite film that eliminates time-intensive and cost-prohibitive processing, traditionally seen during extrusion and dicing inorganic manufacturing. The resulting post-annealed composite film consisting of Bi2Te3 nanowire and CNTs demonstrate a promising candidate for material that can be used for an n-type TE device that has improved energy conversion efficiency.

  14. Hydrothermal synthesis, experimental and theoretical characterization of a novel cocrystal compound in the 2:1 stoichiometric ratio containing 6-methyluracil and dipicolinic acid

    NASA Astrophysics Data System (ADS)

    Eshtiagh-Hosseini, H.; Aghabozorg, H.; Mirzaei, M.; Beyramabadi, S. A.; Eshghi, H.; Morsali, A.; Shokrollahi, A.; Aghaei, R.

    2011-05-01

    This paper reports the hydrothermal synthesis, experimental and theoretical studies of a novel cocrystal compound in the 2:1 stoichiometric ratio of 6-methyluracil (6mu) and dipicolinic acid (pydcH 2) formulated as [6mu] 2[pydcH 2] (1), for the first time. DFT calculations were performed to access the most possible geometry of the title cocrystal compound. All calculations were carried out with the B3LYP hybrid density functional level and 6-311+G(d,p) basis sets. The vibrational frequencies together with the 1H and 13C NMR chemical shifts have been calculated on the fully optimized geometry of 1. The theoretical results are in good agreement with the experimental and solution data. The theoretical, solution, and experimental (elemental analysis, mass spectrometry, FTIR, 1H and 13C NMR spectroscopies) results confirmed our proposed structure for 1 in the 2:1 stoichiometric ratio of 6mu and pydcH 2, respectively. The protonation and equilibrium constants of 6mu and pydcH 2 and constituent systems were determined by potentiometric studies and the corresponding distribution diagrams depicted.

  15. Strength and failure analysis of composite-to-composite adhesive bonds with different surface treatments

    NASA Astrophysics Data System (ADS)

    Paranjpe, Nikhil; Alamir, Mohammed; Alonayni, Abdullah; Asmatulu, Eylem; Rahman, Muhammad M.; Asmatulu, Ramazan

    2018-03-01

    Adhesives are widely utilized materials in aviation, automotive, energy, defense, and marine industries. Adhesive joints are gradually supplanting mechanical fasteners because they are lightweight structures, thus making the assembly lighter and easier. They also act as a sealant to prevent a structural joint from galvanic corrosion and leakages. Adhesive bonds provide high joint strength because of the fact that the load is distributed uniformly on the joint surface, while in mechanical joints, the load is concentrated at one point, thus leading to stress at that point and in turn causing joint failures. This research concentrated on the analysis of bond strength and failure loads in adhesive joint of composite-to-composite surfaces. Different durations of plasma along with the detergent cleaning were conducted on the composite surfaces prior to the adhesive applications and curing processes. The joint strength of the composites increased about 34% when the surface was plasma treated for 12 minutes. It is concluded that the combination of different surface preparations, rather than only one type of surface treatment, provides an ideal joint quality for the composites.

  16. Ideal Cardiovascular Health and Arterial Stiffness in Spanish Adults-The EVIDENT Study.

    PubMed

    García-Hermoso, Antonio; Martínez-Vizcaíno, Vicente; Gomez-Marcos, Manuel Ángel; Cavero-Redondo, Iván; Recio-Rodriguez, José Ignacio; García-Ortiz, Luis

    2018-05-01

    Studies concerning ideal cardiovascular (CV) health and its relationship with arterial stiffness are lacking. This study examined the association between arterial stiffness with ideal CV health as defined by the American Heart Association, across age groups and gender. The cross-sectional study included 1365 adults. Ideal CV health was defined as meeting ideal levels of the following components: 4 behaviors (smoking, body mass index, physical activity, and Mediterranean diet adherence) and 3 factors (total cholesterol, blood pressure, and glycated hemoglobin). Patients were grouped into 3 categories according to their number of ideal CV health metrics: ideal (5-7 metrics), intermediate (3-4 metrics), and poor (0-2 metrics). We analyzed the pulse wave velocity (PWV), the central and radial augmentation indexes, and the ambulatory arterial stiffness index (AASI). The ideal CV health profile was inversely associated with lower arterial radial augmentation index and AASI in both genders, particularly in middle-aged (45-65 years) and in elderly subjects (>65 years). Also in elderly subjects, adjusted models showed that adults with at least 3 health metrics at ideal levels had significantly lower PWV than those with 2 or fewer ideal health metrics. An association was found between a favorable level of ideal CV health metrics and lower arterial stiffness across age groups. Copyright © 2018 National Stroke Association. Published by Elsevier Inc. All rights reserved.

  17. Conversion of broadband thermal radiation in lithium niobate crystals of various compositions

    NASA Astrophysics Data System (ADS)

    Syuy, A. V.; Litvinova, M. N.; Goncharova, P. S.; Sidorov, N. V.; Palatnikov, M. N.; Krishtop, V. V.; Likhtin, V. V.

    2013-05-01

    The conversion of the broadband thermal radiation in stoichiometric ( R = 1) lithium niobate single crystals that are grown from melt with 58.6 mol % of LiO2, congruent ( R = Li/Nb = 0.946) melt with the K2O flux admixture (4.5 and 6.0 wt %), and congruent melt and in congruent single crystals doped with the Zn2+, Gd3+, and Er3+ cations is studied. It is demonstrated that the conversion efficiency of the stoichiometric crystal that is grown from the melt with 58.6 mol % of LiO2 is less than the conversion efficiency of congruent crystal. In addition, the stoichiometric and almost stoichiometric crystals and the doped congruent crystals exhibit the blue shift of the peak conversion intensity in comparison with a nominally pure congruent crystal. For the congruent crystals, the conversion intensities peak at 520 and 495 nm, respectively.

  18. Ideal-Magnetohydrodynamic-Stable Tilting in Field-Reversed Configurations

    NASA Astrophysics Data System (ADS)

    Kanno, Ryutaro; Ishida, Akio; Steinhauer, Loren

    1995-02-01

    The tilting mode in field-reversed configurations (FRC) is examined using ideal-magnetohydrodynamic stability theory. Tilting, a global mode, is the greatest threat for disruption of FRC confinement. Previous studies uniformly found tilting to be unstable in ideal theory: the objective here is to ascertain if stable equilibria were overlooked in past work. Solving the variational problem with the Rayleigh-Ritz technique, tilting-stable equilibria are found for sufficiently hollow current profile and sufficient racetrackness of the separatrix shape. Although these equilibria were not examined previously, the present conclusion is quite surprising. Consequently checks of the method are offered. Even so it cannot yet be claimed with complete certainty that stability has been proved: absolute confirmation of ideal-stable tilting awaits the application of more complete methods.

  19. In vitro investigation of nanohydroxyapatite/poly(L-lactic acid) spindle composites used for bone tissue engineering.

    PubMed

    Yan, W; Zhang, C Y; Xia, L L; Zhang, T; Fang, Q F

    2016-08-01

    Calcium phosphate ceramics such as synthetic hydroxyapatite and tricalcium phosphate are widely used in the clinic, but they stimulate less bone regeneration. In this paper, nano-hydroxyapatite/poly(L-lactic acid) (nano-HA/PLLA) spindle composites with good mechanical performance were fabricated by a modified in situ precipitation method. The HA part of composite, distributing homogenously in PLLA matrix, is spindle shape with size of 10-30 nm in diameter and 60-100 nm in length. The molar ratio of Ca/P in the synthesized nano-HA spindles was deduced as 1.52 from the EDS spectra, which is close to the stoichiometric composition of HA (Ca/P & 1.67). The compress strength is up to 150 MPa when the HA content increase to 20 %. The in vitro tests indicate that HA/PLLA bio-composites have good biodegradability and bioactivity when immersed in simulated body fluid solutions. All the results suggested that HA/PLLA nano-biocomposites are appropriate to be applied as bone substitute in bone tissue engineering.

  20. Primitive ideals of C q [ SL(3)

    NASA Astrophysics Data System (ADS)

    Hodges, Timothy J.; Levasseur, Thierry

    1993-10-01

    The primitive ideals of the Hopf algebra C q [ SL(3)] are classified. In particular it is shown that the orbits in Prim C q [ SL(3)] under the action of the representation group H ≅ C *× C * are parameterized naturally by W×W, where W is the associated Weyl group. It is shown that there is a natural one-to-one correspondence between primitive ideals of C q [ SL(3)] and symplectic leaves of the associated Poisson algebraic group SL(3, C).

  1. Temperature and the Ideal Gas

    ERIC Educational Resources Information Center

    Daisley, R. E.

    1973-01-01

    Presents some organized ideas in thermodynamics which are suitable for use with high school (GCE A level or ONC) students. Emphases are placed upon macroscopic observations and intimate connection of the modern definition of temperature with the concept of ideal gas. (CC)

  2. Ideal photon number amplifier and duplicator

    NASA Technical Reports Server (NTRS)

    Dariano, G. M.

    1992-01-01

    The photon number-amplification and number-duplication mechanism are analyzed in the ideal case. The search for unitary evolutions leads to consider also a number-deamplification mechanism, the symmetry between amplification and deamplification being broken by the integer-value nature of the number operator. Both transformations, amplification and duplication, need an auxiliary field which, in the case of amplification, turns out to be amplified in the inverse way. Input-output energy conservation is accounted for using a classical pump or through frequency-conversion of the fields. Ignoring one of the fields is equivalent to considering the amplifier as an open system involving entropy production. The Hamiltonians of the ideal devices are given and compared with those of realistic systems.

  3. Innovation in neurosurgery: less than IDEAL? A systematic review.

    PubMed

    Muskens, I S; Diederen, S J H; Senders, J T; Zamanipoor Najafabadi, A H; van Furth, W R; May, A M; Smith, T R; Bredenoord, A L; Broekman, M L D

    2017-10-01

    Surgical innovation is different from the introduction of novel pharmaceuticals. To help address this, in 2009 the IDEAL Collaboration (Idea, Development, Exploration, Assessment, Long-term follow-up) introduced the five-stage framework for surgical innovation. To evaluate the framework feasibility for novel neurosurgical procedure introduction, two innovative surgical procedures were examined: the endoscopic endonasal approach for skull base meningiomas (EEMS) and the WovenEndobridge (WEB device) for endovascular treatment of intracranial aneurysms. The published literature on EEMS and WEB devices was systematically reviewed. Identified studies were classified according to the IDEAL framework stage. Next, studies were evaluated for possible categorization according to the IDEAL framework. Five hundred seventy-six papers describing EEMS were identified of which 26 papers were included. No prospective studies were identified, and no studies reported on ethical approval or patient informed consent for the innovative procedure. Therefore, no clinical studies could be categorized according to the IDEAL Framework. For WEB devices, 6229 articles were screened of which 21 were included. In contrast to EEMS, two studies were categorized as 2a and two as 2b. The results of this systematic review demonstrate that both EEMS and WEB devices were not introduced according to the (later developed in the case of EEMS) IDEAL framework. Elements of the framework such as informed consent, ethical approval, and rigorous outcomes reporting are important and could serve to improve the quality of neurosurgical research. Alternative study designs and the use of big data could be useful modifications of the IDEAL framework for innovation in neurosurgery.

  4. Advances in the history of composite resins.

    PubMed

    Minguez, Nieves; Ellacuria, Joseba; Soler, José Ignacio; Triana, Rodrigo; Ibaseta, Guillermo

    2003-11-01

    The use of composite resins as direct restoration material in posterior teeth has demonstrated a great increase, due to esthetic requirements and the controversy regarding the mercury content in silver amalgams. In this article, we have reviewed the composition modifications which have occurred in materials based on resins since their introduction over a half a century ago which have enabled great improvements in their physical and mechanical properties. Likewise, we have highlighted current lines of research, centered on finding the ideal material for replacing silver amalgam as a direct filling material.

  5. Composition variations in pulsed-laser-deposited Y-Ba-Cu-O thin films as a function of deposition parameters

    NASA Technical Reports Server (NTRS)

    Foote, M. C.; Jones, B. B.; Hunt, B. D.; Barner, J. B.; Vasquez, R. P.; Bajuk, L. J.

    1992-01-01

    The composition of pulsed-ultraviolet-laser-deposited Y-Ba-Cu-O films was examined as a function of position across the substrate, laser fluence, laser spot size, substrate temperature, target conditioning, oxygen pressure and target-substrate distance. Laser fluence, laser spot size, and substrate temperature were found to have little effect on composition within the range investigated. Ablation from a fresh target surface results in films enriched in copper and barium, both of which decrease in concentration until a steady state condition is achieved. Oxygen pressure and target-substrate distance have a significant effect on film composition. In vacuum, copper and barium are slightly concentrated at the center of deposition. With the introduction of an oxygen background pressure, scattering results in copper and barium depletion in the deposition center, an effect which increases with increasing target-substrate distance. A balancing of these two effects results in stoichiometric deposition.

  6. TiN films fabricated by reactive gas pulse sputtering: A hybrid design of multilayered and compositionally graded structures

    NASA Astrophysics Data System (ADS)

    Yang, Jijun; Zhang, Feifei; Wan, Qiang; Lu, Chenyang; Peng, Mingjing; Liao, Jiali; Yang, Yuanyou; Wang, Lumin; Liu, Ning

    2016-12-01

    Reactive gas pulse (RGP) sputtering approach was used to prepare TiN thin films through periodically changing the N2/Ar gas flow ratio. The obtained RGPsbnd TiN film possessed a hybrid architecture containing compositionally graded and multilayered structures, composed of hcp Ti-phase and fcc TiN-phase sublayers. Meanwhile, the RGP-TiN film exhibited a composition-oscillation along the film thickness direction, where the Ti-phase sublayer had a compositional gradient and the TiN-phase retained a constant stoichiometric ratio of Ti:N ≈ 1. The film modulation ratio λ (the thicknesses ratio of the Ti and TiN-phase sublayer) can be effectively tuned by controlling the undulation behavior of the N2 partial flow rate. Detailed analysis showed that this hybrid structure originated from a periodic transition of the film growth mode during the reactive sputtering process.

  7. Stimulated Raman scattering in an optical parametric oscillator based on periodically poled MgO-doped stoichiometric LiTaO3.

    PubMed

    My, T-H; Robin, O; Mhibik, O; Drag, C; Bretenaker, F

    2009-03-30

    The evolution of the spectrum of a singly resonant optical parametric oscillator based on an MgO-doped periodically poled stoichiometric lithium tantalate crystal is observed when the pump power is varied. The onset of cascade Raman lasing due to stimulated Raman scattering in the nonlinear crystal is analyzed. Spurious frequency doubling and sum-frequency generation phenomena are observed and understood. A strong reduction of the intracavity Raman scattering is obtained by a careful adjustment of the cavity losses.

  8. Effect of gender composition of school on body concerns in adolescent women.

    PubMed

    Tiggemann, M

    2001-03-01

    This study aimed to investigate the role of gender composition of school on body figure preferences, eating disorder symptomology, and role concerns. Questionnaires were completed by 261 Australian adolescent girls in two private single-sex and two private coeducational school environments. There was no difference in nominated ideal figure or eating disorder scores between the schools. However, girls in the single-sex schools placed a greater emphasis on achievement than their counterparts at the coeducational schools. These role concerns had a differential impact on prediction of the ideal figure, whereby the importance placed on intelligence and professional success predicted the choice of a thinner ideal figure for the single-sex schools, but a larger ideal for the coeducational schools. It was concluded that the motivation for thinness differs between single-sex and coeducational schools.

  9. Topological photonic crystal with ideal Weyl points

    NASA Astrophysics Data System (ADS)

    Wang, Luyang; Jian, Shao-Kai; Yao, Hong

    Weyl points in three-dimensional photonic crystals behave as monopoles of Berry flux in momentum space. Here, based on symmetry analysis, we show that a minimal number of symmetry-related Weyl points can be realized in time-reversal invariant photonic crystals. We propose to realize these ``ideal'' Weyl points in modified double-gyroid photonic crystals, which is confirmed by our first-principle photonic band-structure calculations. Photonic crystals with ideal Weyl points are qualitatively advantageous in applications such as angular and frequency selectivity, broadband invisibility cloaking, and broadband 3D-imaging.

  10. Composite material hollow antiresonant fibers.

    PubMed

    Belardi, Walter; De Lucia, Francesco; Poletti, Francesco; Sazio, Pier J

    2017-07-01

    We study novel designs of hollow-core antiresonant fibers comprising multiple materials in their core-boundary membrane. We show that these types of fibers still satisfy an antiresonance condition and compare their properties to those of an ideal single-material fiber with an equivalent thickness and refractive index. As a practical consequence of this concept, we discuss the first realization and characterization of a composite silicon/glass-based hollow antiresonant fiber.

  11. High dose neutron irradiations of Hi-Nicalon Type S silicon carbide composites, Part 1: Microstructural evaluations

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Perez-Bergquist, Alex G.; Nozawa, Takashi; Shih, Chunghao Phillip

    Over the past decade, significant progress has been made in the development of silicon carbide (SiC) composites, composed of near-stoichiometric SiC fibers embedded in a crystalline SiC matrix, to the point that such materials can now be considered nuclear grade. Recent neutron irradiation studies of Hi-Nicalon Type S SiC composites showed excellent radiation response at damage levels of 30-40 dpa at temperatures of 300-800 °C. However, more recent studies of these same fiber composites irradiated to damage levels of >70 dpa at similar temperatures showed a marked decrease in ultimate flexural strength, particularly at 300 °C. Here, electron microscopy ismore » used to analyze the microstructural evolution of these irradiated composites in order to investigate the cause of the degradation. While minimal changes were observed in Hi-Nicalon Type S SiC composites irradiated at 800 °C, substantial microstructural evolution is observed in those irradiated at 300° C. Furthermore, carbonaceous particles in the fibers grew by 25% compared to the virgin case, and severe cracking occurred at interphase layers.« less

  12. Prevalence of ideal cardiovascular health in European adolescents: The HELENA study.

    PubMed

    Henriksson, Pontus; Henriksson, Hanna; Gracia-Marco, Luis; Labayen, Idoia; Ortega, Francisco B; Huybrechts, Inge; España-Romero, Vanesa; Manios, Yannis; Widhalm, Kurt; Dallongeville, Jean; González-Gross, Marcela; Marcos, Ascensión; Moreno, Luis A; Castillo, Manuel J; Ruiz, Jonatan R

    2017-08-01

    The ideal cardiovascular health (iCVH) construct consists of 4 health behaviours and 3 health factors and is strongly related to later cardiovascular disease. However, the prevalence of iCVH in European adolescents is currently unknown. The Healthy Lifestyle in Europe by Nutrition in Adolescence (HELENA) study is a cross-sectional, multicentre study conducted in 9 European countries during 2006-2007 and included 3528 adolescents (1683 boys and 1845 girls) between 12.5 and 17.5years of age. Status (ideal vs. non-ideal) for the health behaviours (smoking status, body mass index, physical activity and diet) and health factors (total cholesterol, blood pressure and fasting glucose) were determined. Overall, the prevalence of ideal health behaviours was low; non-smoking (60.9% ideal), body mass index (76.8%), physical activity (62.1%), and diet (1.7%). The prevalence of ideal health factors was; total cholesterol (65.8%), blood pressure (62.0%) and plasma glucose (88.8%). The low prevalence of iCVH behaviours, especially diet and physical activity, identified in European adolescents is likely to influence later cardiovascular health which strongly motivates efforts to increase ideal health behaviours in this population. Copyright © 2017 Elsevier B.V. All rights reserved.

  13. Ideal affect in daily life: implications for affective experience, health, and social behavior.

    PubMed

    Tsai, Jeanne L

    2017-10-01

    Over the last decade, researchers have increasingly demonstrated that ideal affect-the affective states that people value and ideally want to feel-shapes different aspects of daily life. Here I briefly review Affect Valuation Theory (AVT), which integrates ideal affect into existing models of affect and emotion by identifying the causes and consequences of variation in ideal affect. I then describe recent research that applies AVT to the valuation of negative states as well as more complex states, examines how ideal affect shapes momentary affective experience, suggests that ideal affect has both direct and indirect effects on health, and illustrates that people's ideal affect shapes how they judge and respond to others. Finally, I discuss the implications of cultural and individual differences in ideal affect for clinical, educational, work, and leisure settings. Copyright © 2017 Elsevier Ltd. All rights reserved.

  14. Evaluation of the mechanical and thermal properties of coffee tree wood flour - polypropylene composites

    USDA-ARS?s Scientific Manuscript database

    Columbian coffee trees are subject to frequent replacement plantings due to disease and local climate changes which makes them an ideal source of wood fibers for wood plastic composites (WPC). Composites of polypropylene (PP) consisting of 25% and 40% by weight of coffee wood flour (CF) and 0% or 5%...

  15. Impact of non-ideal analyte behavior on the separation of protein aggregates by asymmetric flow field-flow fractionation.

    PubMed

    Boll, Björn; Josse, Lena; Heubach, Anja; Hochenauer, Sophie; Finkler, Christof; Huwyler, Jörg; Koulov, Atanas V

    2018-04-25

    Asymmetric flow field-flow fractionation is a valuable tool for the characterization of protein aggregates in biotechnology owing to its broad size range and unique separation principle. However, in practice asymmetric flow field-flow fractionation is non-trivial to use due to the major deviations from theory and the influence on separation by various factors that are not fully understood. Here we report methods to assess the non-ideal effects that influence asymmetric flow field-flow fractionation separation and for the first time identify experimentally the main factors that impact it. Furthermore, we propose new approaches to minimize such non-ideal behavior, showing that by adjusting the mobile phase composition (pH and ionic strength) the resolution of asymmetric flow field-flow fractionation separation can be drastically improved. Additionally, we propose a best practice method for new proteins. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

  16. Cardiorespiratory fitness and ideal cardiovascular health in European adolescents.

    PubMed

    Ruiz, Jonatan R; Huybrechts, Inge; Cuenca-García, Magdalena; Artero, Enrique G; Labayen, Idoia; Meirhaeghe, Aline; Vicente-Rodriguez, German; Polito, Angela; Manios, Yannis; González-Gross, Marcela; Marcos, Ascensión; Widhalm, Kurt; Molnar, Denes; Kafatos, Anthony; Sjöström, Michael; Moreno, Luis A; Castillo, Manuel J; Ortega, Francisco B

    2015-05-15

    We studied in European adolescents (i) the association between cardiorespiratory fitness and ideal cardiovascular health as defined by the American Heart Association and (ii) whether there is a cardiorespiratory fitness threshold associated with a more favourable cardiovascular health profile. Participants included 510 (n=259 girls) adolescents from 9 European countries. The 20 m shuttle run test was used to estimate cardiorespiratory fitness. Ideal cardiovascular health was defined as meeting ideal levels of the following components: four behaviours (smoking, body mass index, physical activity and diet) and three factors (total cholesterol, blood pressure and glucose). Higher levels of cardiorespiratory fitness were associated with a higher number of ideal cardiovascular health components in both boys and girls (both p for trend ≤0.001). Levels of cardiorespiratory fitness were significantly higher in adolescents meeting at least four ideal components (13% higher in boys, p<0.001; 6% higher in girls, p=0.008). Receiver operating characteristic curve analyses showed a significant discriminating accuracy of cardiorespiratory fitness in identifying the presence of at least four ideal cardiovascular health components (43.8 mL/kg/min in boys and 34.6 mL/kg/min in girls, both p<0.001). The results suggest a hypothetical cardiorespiratory fitness level associated with a healthier cardiovascular profile in adolescents. The fitness standards could be used in schools as part of surveillance and/or screening systems to identify youth with poor health behaviours who might benefit from intervention programmes. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

  17. Non-ideal Solution Thermodynamics of Cytoplasm

    PubMed Central

    Ross-Rodriguez, Lisa U.; McGann, Locksley E.

    2012-01-01

    Quantitative description of the non-ideal solution thermodynamics of the cytoplasm of a living mammalian cell is critically necessary in mathematical modeling of cryobiology and desiccation and other fields where the passive osmotic response of a cell plays a role. In the solution thermodynamics osmotic virial equation, the quadratic correction to the linear ideal, dilute solution theory is described by the second osmotic virial coefficient. Herein we report, for the first time, intracellular solution second osmotic virial coefficients for four cell types [TF-1 hematopoietic stem cells, human umbilical vein endothelial cells (HUVEC), porcine hepatocytes, and porcine chondrocytes] and further report second osmotic virial coefficients indistinguishable from zero (for the concentration range studied) for human hepatocytes and mouse oocytes. PMID:23840923

  18. Ideal Standards, Acceptance, and Relationship Satisfaction: Latitudes of Differential Effects

    PubMed Central

    Buyukcan-Tetik, Asuman; Campbell, Lorne; Finkenauer, Catrin; Karremans, Johan C.; Kappen, Gesa

    2017-01-01

    We examined whether the relations of consistency between ideal standards and perceptions of a current romantic partner with partner acceptance and relationship satisfaction level off, or decelerate, above a threshold. We tested our hypothesis using a 3-year longitudinal data set collected from heterosexual newlywed couples. We used two indicators of consistency: pattern correspondence (within-person correlation between ideal standards and perceived partner ratings) and mean-level match (difference between ideal standards score and perceived partner score). Our results revealed that pattern correspondence had no relation with partner acceptance, but a positive linear/exponential association with relationship satisfaction. Mean-level match had a significant positive association with actor’s acceptance and relationship satisfaction up to the point where perceived partner score equaled ideal standards score. Partner effects did not show a consistent pattern. The results suggest that the consistency between ideal standards and perceived partner attributes has a non-linear association with acceptance and relationship satisfaction, although the results were more conclusive for mean-level match. PMID:29033876

  19. SILICATE COMPOSITION OF THE INTERSTELLAR MEDIUM

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Fogerty, S.; Forrest, W.; Watson, D. M.

    2016-10-20

    The composition of silicate dust in the diffuse interstellar medium and in protoplanetary disks around young stars informs our understanding of the processing and evolution of the dust grains leading up to planet formation. An analysis of the well-known 9.7 μ m feature indicates that small amorphous silicate grains represent a significant fraction of interstellar dust and are also major components of protoplanetary disks. However, this feature is typically modeled assuming amorphous silicate dust of olivine and pyroxene stoichiometries. Here, we analyze interstellar dust with models of silicate dust that include non-stoichiometric amorphous silicate grains. Modeling the optical depth alongmore » lines of sight toward the extinguished objects Cyg OB2 No. 12 and ζ Ophiuchi, we find evidence for interstellar amorphous silicate dust with stoichiometry intermediate between olivine and pyroxene, which we simply refer to as “polivene.” Finally, we compare these results to models of silicate emission from the Trapezium and protoplanetary disks in Taurus.« less

  20. Handgrip Strength and Ideal Cardiovascular Health among Colombian Children and Adolescents.

    PubMed

    Ramírez-Vélez, Robinson; Tordecilla-Sanders, Alejandra; Correa-Bautista, Jorge Enrique; Peterson, Mark D; Garcia-Hermoso, Antonio

    2016-12-01

    To evaluate the association between handgrip strength and ideal cardiovascular health (CVH) in Colombian children and adolescents. During the 2014-2015 school years, we examined a cross-sectional component of the FUPRECOL (Association for Muscular Strength with Early Manifestation of Cardiovascular Disease Risk Factors among Colombian Children and Adolescents) study. Participants included 1199 (n = 627 boys) youths from Bogota (Colombia). Handgrip strength was measured with a standard adjustable hand held dynamometer and expressed relative to body mass (handgrip/body mass) and as absolute values in kilograms. Ideal CVH, as defined by the American Heart Association, was determined as meeting ideal levels of the following components: 4 behaviors (smoking status, body mass index, cardiorespiratory fitness, and diet) and 3 factors (total cholesterol, blood pressure, and glucose). Higher levels of handgrip strength (both absolute and relative values) were associated with a higher frequency of ideal CVH metrics in both sexes (P for trend ≤ .001). Also, higher levels of handgrip strength were associated with a greater number of ideal health behaviors (P for trend < .001 in both boys and girls), and with a higher number of ideal health factors in boys (P for trend < .001). Finally, levels of handgrip strength were similar between ideal versus nonideal glucose or total cholesterol groups in girls. Handgrip strength was strongly associated with ideal CVH in Colombian children and adolescents, and thus supports the relevance of early targeted interventions to promote strength adaptation and preservation as part of primordial prevention. Copyright © 2016 Elsevier Inc. All rights reserved.

  1. Chemical Laws, Idealization and Approximation

    NASA Astrophysics Data System (ADS)

    Tobin, Emma

    2013-07-01

    This paper examines the notion of laws in chemistry. Vihalemm ( Found Chem 5(1):7-22, 2003) argues that the laws of chemistry are fundamentally the same as the laws of physics they are all ceteris paribus laws which are true "in ideal conditions". In contrast, Scerri (2000) contends that the laws of chemistry are fundamentally different to the laws of physics, because they involve approximations. Christie ( Stud Hist Philos Sci 25:613-629, 1994) and Christie and Christie ( Of minds and molecules. Oxford University Press, New York, pp. 34-50, 2000) agree that the laws of chemistry are operationally different to the laws of physics, but claim that the distinction between exact and approximate laws is too simplistic to taxonomise them. Approximations in chemistry involve diverse kinds of activity and often what counts as a scientific law in chemistry is dictated by the context of its use in scientific practice. This paper addresses the question of what makes chemical laws distinctive independently of the separate question as to how they are related to the laws of physics. From an analysis of some candidate ceteris paribus laws in chemistry, this paper argues that there are two distinct kinds of ceteris paribus laws in chemistry; idealized and approximate chemical laws. Thus, while Christie ( Stud Hist Philos Sci 25:613-629, 1994) and Christie and Christie ( Of minds and molecules. Oxford University Press, New York, pp. 34--50, 2000) are correct to point out that the candidate generalisations in chemistry are diverse and heterogeneous, a distinction between idealizations and approximations can nevertheless be used to successfully taxonomise them.

  2. The ideal imaging AR waveguide

    NASA Astrophysics Data System (ADS)

    Grey, David J.

    2017-06-01

    Imaging waveguides are a key development that are helping to create the Augmented Reality revolution. They have the ability to use a small projector as an input and produce a wide field of view, large eyebox, full colour, see-through image with good contrast and resolution. WaveOptics is at the forefront of this AR technology and has developed and demonstrated an approach which is readily scalable. This paper presents our view of the ideal near-to-eye imaging AR waveguide. This will be a single-layer waveguide which can be manufactured in high volume and low cost, and is suitable for small form factor applications and all-day wear. We discuss the requirements of the waveguide for an excellent user experience. When enhanced (AR) viewing is not required, the waveguide should have at least 90% transmission, no distracting artifacts and should accommodate the user's ophthalmic prescription. When enhanced viewing is required, additionally, the waveguide requires excellent imaging performance, this includes resolution to the limit of human acuity, wide field of view, full colour, high luminance uniformity and contrast. Imaging waveguides are afocal designs and hence cannot provide ophthalmic correction. If the user requires this correction then they must wear either contact lenses, prescription spectacles or inserts. The ideal imaging waveguide would need to cope with all of these situations so we believe it must be capable of providing an eyebox at an eye relief suitable for spectacle wear which covers a significant range of population inter-pupillary distances. We describe the current status of our technology and review existing imaging waveguide technologies against the ideal component.

  3. Long discontinuous fiber composite structure: Forming and structural mechanics

    NASA Technical Reports Server (NTRS)

    Pipes, R. B.; Santare, M. H.; Otoole, B. J.; Beaussart, A. J.; Deheer, D. C.; Okine, R. K.

    1991-01-01

    Cost effective composite structure has motivated the investigation of several new approaches to develop composite structure from innovative material forms. Among the promising new approaches is the conversion of planar sheet to components of complex curvature through sheet forming or stretch forming. In both cases, the potential for material stretch in the fiber direction appears to offer a clear advantage in formability over continuous fiber systems. In the present study, the authors have established a framework which allows the simulation of the anisotropic mechanisms of deformation of long discontinuous fiber laminates wherein the matrix phase is a viscous fluid. The initial study focuses upon the establishment of micromechanics models for prediction of the effective anisotropic viscosities of the oriented fiber assembly in a viscous matrix. Next, the developed constitutive relation is employed through an analogy with incompressible elasticity to exercise the finite element technique for determination of local fiber orientation and laminate thickness after forming. Results are presented for the stretch bending of a curved beam from an arbitrary composite laminate and the bulging of a clamped sheet. Structural analyses are conducted to determine the effect of microstructure on the performance of curved beams manufactured from long discontinuous fiber composites. For the purposes of this study, several curved beams with ideal and non-ideal microstructures are compared for response under pure bending. Material parameters are determined from a separate microstructural analysis.

  4. Charge-Trapping-Induced Non-Ideal Behaviors in Organic Field-Effect Transistors.

    PubMed

    Un, Hio-Ieng; Cheng, Peng; Lei, Ting; Yang, Chi-Yuan; Wang, Jie-Yu; Pei, Jian

    2018-05-01

    Organic field-effect transistors (OFETs) with impressively high hole mobilities over 10 cm 2 V -1 s -1 and electron mobilities over 1 cm 2 V -1 s -1 have been reported in the past few years. However, significant non-ideal electrical characteristics, e.g., voltage-dependent mobilities, have been widely observed in both small-molecule and polymer systems. This issue makes the accurate evaluation of the electrical performance impossible and also limits the practical applications of OFETs. Here, a semiconductor-unrelated, charge-trapping-induced non-ideality in OFETs is reported, and a revised model for the non-ideal transfer characteristics is provided. The trapping process can be directly observed using scanning Kelvin probe microscopy. It is found that such trapping-induced non-ideality exists in OFETs with different types of charge carriers (p-type or n-type), different types of dielectric materials (inorganic and organic) that contain different functional groups (OH, NH 2 , COOH, etc.). As fas as it is known, this is the first report for the non-ideal transport behaviors in OFETs caused by semiconductor-independent charge trapping. This work reveals the significant role of dielectric charge trapping in the non-ideal transistor characteristics and also provides guidelines for device engineering toward ideal OFETs. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. [Spatial characteristics analysis of Huizhou-Styled Village based on ideal ecosystem model and 3D landscape indices: A case in Chengkan, China].

    PubMed

    Yao, Meng Yuan; Yan, Shi Jiang; Wu, Yan Lan

    2016-12-01

    Huizhou-Styled Village is a typical representative of the traditional Chinese ancient villages. It preserves plentiful information of the regional culture and ecological connotation. The Huizhou-Style is the apotheosis of harmony between the Chinese ancient people and nature. The research and protection of Huizhou-Styled Village plays a very important role in fields of ecology, geography, architecture and esthetics. This paper took Chengkan Village of Anhui Province as an exa-mple, and proposed a new model of ideal ecosystem oriented in theories of Feng-shui and psychological field. The new method of characterizing 3D landscape index was introduced to explore the spatial patterns of Huizhou-Styled Village and the functionality of the composited landscape components in a quantitative way. The results indicated that, Chengkan Village showed a spatially composited pattern of "mountain-forest-village-river-forest". It formed an ideal settlement ring structure with human architecture in the center and natural landscape around in the horizontal and vertical horizons. The traditional method based on the projection distance caused the deviation of the landscape index, such as underestimating the area and distance of landscape patch. The 3D landscape index of average patch area was 6.7% higher than the 2D landscape index. The increasing rate ofarea proportion in 3D index was 1.0% higher than that of 2D index in forest lands. Area proportion of the other landscapes decreased, especially the artificial landscapes like construction and cropland landscapes. The area and perimeter metric were underestimated, whereas the shape metric and the diversity metric were overestimated. This caused the underestimation of the dominance of natural patches was underestimated and the overestimation of the dominance of artificial patches during the analysis of landscape pattern. The 3D landscape index showed that the natural elements and their combination in Chengkan Village ecosystem

  6. Characterization of near-stoichiometric Ti:LiNbO(3) strip waveguides with varied substrate refractive index in the guiding layer.

    PubMed

    Zhang, De-Long; Zhang, Pei; Zhou, Hao-Jiang; Pun, Edwin Yue-Bun

    2008-10-01

    We have demonstrated the possibility that near-stoichiometric Ti:LiNbO(3) strip waveguides are fabricated by carrying out vapor transport equilibration at 1060 degrees C for 12 h on a congruent LiNbO(3) substrate with photolithographically patterned 4-8 microm wide, 115 nm thick Ti strips. Optical characterizations show that these waveguides are single mode at 1.5 microm and show a waveguide loss of 1.3 dB/cm for TM mode and 1.1 dB/cm for TE mode. In the width/depth direction of the waveguide, the mode field follows the Gauss/Hermite-Gauss function. Secondary-ion-mass spectrometry (SIMS) was used to study Ti-concentration profiles in the depth direction and on the surface of the 6 microm wide waveguide. The result shows that the Ti profile follows a sum of two error functions along the width direction and a complementary error function in the depth direction. The surface Ti concentration, 1/e width and depth, and mean diffusivities along the width and depth directions of the guide are similar to 3.0 x 10(21) cm(-3), 3.8 microm, 2.6 microm, 0.30 and 0.14 microm(2)/h, respectively. Micro-Raman analysis was carried out on the waveguide endface to characterize the depth profile of Li composition in the guiding layer. The results show that the depth profile of Li composition also follows a complementary error function with a 1/e depth of 3.64 microm. The mean ([Li(Li)]+[Ti(Li)])/([Nb(Nb)]+[Ti(Nb)]) ratio in the waveguide layer is about 0.98. The inhomogeneous Li-composition profile results in a varied substrate index in the guiding layer. A two-dimensional refractive index profile model in the waveguide is proposed by taking into consideration the varied substrate index and assuming linearity between Ti-induced index change and Ti concentration. The net waveguide surface index increments at 1545 nm are 0.0114 and 0.0212 for ordinary and extraordinary rays, respectively. Based upon the constructed index model, the fundamental mode field profile was calculated using the

  7. Compensation of non-ideal beam splitter polarization distortion effect in Michelson interferometer

    NASA Astrophysics Data System (ADS)

    Liu, Yeng-Cheng; Lo, Yu-Lung; Liao, Chia-Chi

    2016-02-01

    A composite optical structure consisting of two quarter-wave plates and a single half-wave plate is proposed for compensating for the polarization distortion induced by a non-ideal beam splitter in a Michelson interferometer. In the proposed approach, the optimal orientations of the optical components within the polarization compensator are determined using a genetic algorithm (GA) such that the beam splitter can be treated as a free-space medium and modeled using a unit Mueller matrix accordingly. Two implementations of the proposed polarization controller are presented. In the first case, the compensator is placed in the output arm of Michelson interferometer such that the state of polarization of the interfered output light is equal to that of the input light. However, in this configuration, the polarization effects induced by the beam splitter in the two arms of the interferometer structure cannot be separately addressed. Consequently, in the second case, compensator structures are placed in the Michelson interferometer for compensation on both the scanning and reference beams. The practical feasibility of the proposed approach is introduced by considering a Mueller polarization-sensitive (PS) optical coherence tomography (OCT) structure with three polarization controllers in the input, reference and sample arms, respectively. In general, the results presented in this study show that the proposed polarization controller provides an effective and experimentally-straightforward means of compensating for the polarization distortion effects induced by the non-ideal beam splitters in Michelson interferometers and Mueller PS-OCT structures.

  8. The place of the ideal observer in medical ethics.

    PubMed

    Churchill, L R

    1983-01-01

    The idea of an ideal observer is frequently employed in ethical reasoning and has recently been introduced into medical ethics. The contemporary use of this idea, however, is deeply flawed. It ignores important social and personal dimensions of ethics. By espousing a perspective of observation removed from history and community, the ideal observer notion encourages a pretense of objectivity and overlooks the distortions of distance. If taken seriously as a model for choice, the ideal observer is incoherent, as it dispenses with the concrete moral agent and the locus of choice. Adam Smith's 'impartial spectator' is examined as a more adequate statement of the need for appreciating diverse perspectives in ethical choices.

  9. A parallel input composite transimpedance amplifier.

    PubMed

    Kim, D J; Kim, C

    2018-01-01

    A new approach to high performance current to voltage preamplifier design is presented. The design using multiple operational amplifiers (op-amps) has a parasitic capacitance compensation network and a composite amplifier topology for fast, precision, and low noise performance. The input stage consisting of a parallel linked JFET op-amps and a high-speed bipolar junction transistor (BJT) gain stage driving the output in the composite amplifier topology, cooperating with the capacitance compensation feedback network, ensures wide bandwidth stability in the presence of input capacitance above 40 nF. The design is ideal for any two-probe measurement, including high impedance transport and scanning tunneling microscopy measurements.

  10. A parallel input composite transimpedance amplifier

    NASA Astrophysics Data System (ADS)

    Kim, D. J.; Kim, C.

    2018-01-01

    A new approach to high performance current to voltage preamplifier design is presented. The design using multiple operational amplifiers (op-amps) has a parasitic capacitance compensation network and a composite amplifier topology for fast, precision, and low noise performance. The input stage consisting of a parallel linked JFET op-amps and a high-speed bipolar junction transistor (BJT) gain stage driving the output in the composite amplifier topology, cooperating with the capacitance compensation feedback network, ensures wide bandwidth stability in the presence of input capacitance above 40 nF. The design is ideal for any two-probe measurement, including high impedance transport and scanning tunneling microscopy measurements.

  11. Quantifying ataxia: ideal trajectory analysis--a technical note

    NASA Technical Reports Server (NTRS)

    McPartland, M. D.; Krebs, D. E.; Wall, C. 3rd

    2000-01-01

    We describe a quantitative method to assess repeated stair stepping stability. In both the mediolateral (ML) and anterioposterior (AP) directions, the trajectory of the subject's center of mass (COM) was compared to an ideal sinusoid. The two identified sinusoids were unique in each direction but coupled. Two dimensionless numbers-the mediolateral instability index (IML) and AP instability index (IAP)-were calculated using the COM trajectory and ideal sinusoids for each subject with larger index values resulting from less stable performance. The COM trajectories of nine nonimpaired controls and six patients diagnosed with unilateral or bilateral vestibular labyrinth hypofunction were analyzed. The average IML and IAP values of labyrinth disorder patients were respectively 127% and 119% greater than those of controls (p<0.014 and 0.006, respectively), indicating that the ideal trajectory analysis distinguishes persons with labyrinth disorder from those without. The COM trajectories also identify movement inefficiencies attributable to vestibulopathy.

  12. An Ideal Remedial Reading Program.

    ERIC Educational Resources Information Center

    Boettcher, Judith A.

    An ideal secondary level remedial reading program would be based on the philosophy that both freedom and structure are required, that learning demands involvement and feedback, and that success breeds success. Such programs should be structured (i.e., based on clearly defined content and a clearly designated mode of presentation). There are many…

  13. Growth of LiNbO{sub 3}:Er Crystals and concentration dependences of their properties

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Palatnikov, M. N., E-mail: palat-mn@chemy.kolasc.net.ru; Biryukova, I. V.; Shcherbina, O. B.

    2016-11-15

    A series of lithium niobate (LiNbO{sub 3}) crystals of congruent and stoichiometric compositions, doped with erbium, have been grown under non-steady-state thermal conditions. A series of LiNbO{sub 3}:Zn crystals, nominally pure LiNbO{sub 3} crystals of congruent and stoichiometric compositions, and a LiNbO{sub 3}:B crystal have also been grown. Both growth conditions and concentration dependences of physicochemical, ferroelectric, and structural characteristics of LiNbO{sub 3}:Er crystals are investigated. The growth regular domain microstructures and periodic nanostructures in LiNbO{sub 3}:Er crystals are analyzed by optical microscopy and atomic force microscopy (AFM). A comparative study of the optical homogeneity and photorefractive properties of LiNbO{submore » 3}:Er crystals of congruent and stoichiometric compositions and the Raman spectra of LiNbO{sub 3} crystals of different compositions is performed.« less

  14. A Unified Theory of Non-Ideal Gas Lattice Boltzmann Models

    NASA Technical Reports Server (NTRS)

    Luo, Li-Shi

    1998-01-01

    A non-ideal gas lattice Boltzmann model is directly derived, in an a priori fashion, from the Enskog equation for dense gases. The model is rigorously obtained by a systematic procedure to discretize the Enskog equation (in the presence of an external force) in both phase space and time. The lattice Boltzmann model derived here is thermodynamically consistent and is free of the defects which exist in previous lattice Boltzmann models for non-ideal gases. The existing lattice Boltzmann models for non-ideal gases are analyzed and compared with the model derived here.

  15. Composition effects on mechanical properties of tungsten-rhenium-hafnium-carbon alloys

    NASA Technical Reports Server (NTRS)

    Witzke, W. R.

    1973-01-01

    The mechanical properties of rod and sheet fabricated from arc melted W-4Re-Hf-C alloys containing up to about 0.8 mol percent hafnium carbide (HfC) were evaluated in the as-worked condition. The DBTT's of electropolished bend and tensile specimens were independent of HfC content in this range but dependent on excess Hf or C above that required for stoichiometric HfC. Low temperature ductility was a maximum at Hf contents slightly in excess of stoichiometric. Variations in high temperature strength were also dependent on excess Hf and C. Maximum creep strengthening also occurred at Hf contents in excess of stoichiometric. Analysis of extracted second phase particles indicated that creep strength was reduced by increasing WC content in the HfC particles.

  16. Recent Developments in Carbonylation Chemistry Using [13 C]CO, [11 C]CO and [14 C]CO.

    PubMed

    Nielsen, Dennis U; Neumann, Karoline T; Lindhardt, Anders T; Skrydstrup, Troels

    2018-06-01

    Carbon monoxide represents the most important C1-building block for the chemical industry, both for the production of bulk and fine chemicals, but also for synthetic fuels. Yet, its toxicity and subsequently its cautious handling has limited its applications in medicinal chemistry research and in particular for the synthesis of pharmaceutically relevant molecules. Recent years have nevertheless witnessed a considerable headway on the development of carbon monoxide surrogates and reactor systems, which provide an ideal setting for performing carbonylation chemistry with stoichiometric and sub-stoichiometric carbon monoxide. Such set-ups are particularly ideal for the introduction of isotope labels such as carbon-11, carbon-13 and carbon-14 into bioactive compounds. This review summarizes this growing field and examines the large number of carbonylation reactions that can be exploited for the introduction of a carbon isotope. This article is protected by copyright. All rights reserved.

  17. Preparation and microstructural characterization of TiC and Ti{sub 0.6}W{sub 0.4}/TiC{sub 0.6} composite thin films obtained by activated reactive evaporation

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Montes de Oca, J. A.; LePetitcorps, Y.; Manaud, J.-P.

    2008-05-15

    Titanium carbide-based coatings were deposited on W substrates at a high coating growth rate by activated reactive evaporation at 500 and 600 deg. C in a L560 Leybold system using propene as reactive atmosphere. The crystal structure, lattice parameter, preferred orientation, and grain size of the coatings were determined by x-ray diffraction technique using Cu K{alpha}. The analysis of the coating morphology was performed by scanning electron microscopy (SEM), and the composition of the films was analyzed by Auger electron spectroscopy and electron-probe microanalysis. Experimental results suggested that temperature was one of the most important parameters in the fabrication ofmore » stoichiometric TiC coatings. Thus, TiC coatings were obtained at 600 deg. C, whereas TiC{sub 0.6} nonstoichiometric coatings codeposited with a free Ti phase were obtained at 500 deg. C, giving rise to the formation of a composite thin film. After annealing at 1000 deg. C, the stoichiometric films remained stable, but a crack pattern was formed over the entire coating surface. In addition, Ti{sub 0.6}W{sub 0.4}/TiC{sub 0.6} composite thin coatings were obtained for the films synthesized at 500 deg. C. The formation of a Ti{sub 0.6}W{sub 0.4} ductile phase in the presence of a TiC{sub 0.6} phase was responsible to avoid the coating cracking.« less

  18. Chemical Laws, Idealization and Approximation

    ERIC Educational Resources Information Center

    Tobin, Emma

    2013-01-01

    This paper examines the notion of laws in chemistry. Vihalemm ("Found Chem" 5(1):7-22, 2003) argues that the laws of chemistry are fundamentally the same as the laws of physics they are all "ceteris paribus" laws which are true "in ideal conditions". In contrast, Scerri (2000) contends that the laws of chemistry are…

  19. Delivering ideal employee experiences.

    PubMed

    Weiss, Marjorie D; Tyink, Steve; Kubiak, Curt

    2009-05-01

    Employee-centric strategies have moved from employee satisfaction and brand awareness to employee "affinity" or "attachment." In today's marketplace, occupational health nurses understand that differentiation (i.e., the perception of uniqueness) is the direct result of superior employee interactions, which lead to better employee care, enduring employee relationships, loyal employees, and satisfied employers. What drives employees to occupational health nurse attachment? The answer is a passion for rising above the competition to create ideal employee experiences.

  20. Robotic kidney transplantation with regional hypothermia: evolution of a novel procedure utilizing the IDEAL guidelines (IDEAL phase 0 and 1).

    PubMed

    Menon, Mani; Abaza, Ronney; Sood, Akshay; Ahlawat, Rajesh; Ghani, Khurshid R; Jeong, Wooju; Kher, Vijay; Kumar, Ramesh K; Bhandari, Mahendra

    2014-05-01

    Surgical innovation is essential for progress of surgical science, but its implementation comes with potential harms during the learning phase. The Balliol Collaboration has recommended a set of guidelines (Innovation, Development, Exploration, Assessment, Long-term study [IDEAL]) that permit innovation while minimizing complications. To utilize the IDEAL model of surgical innovation in the development of a novel surgical technique, robotic kidney transplantation (RKT) with regional hypothermia, and describe the process of discovery and development. Phase 0 (simulation) studies included the establishment of techniques for pelvic cooling, graft placement in a robotic prostatectomy model, and simulation of the RKT procedure in a cadaveric model. Phase 1 (innovation) studies began in January 2013 and involved treatment of a highly selective small group of patients (n=7), using the principles utilized in the phase 0 studies, at a tertiary referral center. IDEAL model implementation in the development of RKT with regional hypothermia. For phase 0 studies, the outcomes evaluated included pelvic and body temperature measurements, and technical feasibility assessment. The primary outcome during phase 1 was post-transplant graft function. Other outcomes measured were operative and ischemic times, perioperative complications, and intracorporeal graft surface temperature. Phase 0 (simulation phase): Pelvic cooling to 15-20(o)C was achieved reproducibly. Using the surgical approach developed for robotic radical prostatectomy, vascular and ureterovesical anastomoses could be done without redocking the robot. Phase 1 (innovation phase): All patients underwent live-donor RKT in the lithotomy position. All grafts functioned immediately. Mean console, anastomotic, and warm ischemia times were 154 min, 29 min, and 2 min, respectively. One patient was re-explored on postoperative day 1. Adherence to the IDEAL guidelines put forth by the Balliol Collaboration provided a practical

  1. Micromechanics of compression failures in open hole composite laminates

    NASA Technical Reports Server (NTRS)

    Guynn, E. Gail; Bradley, Walter L.

    1987-01-01

    The high strength-to-weight ratio of composite materials is ideally suited for aerospace applications where they already are used in commercial and military aircraft secondary structures and will soon be used for heavily loaded primary structures. One area impeding the widespread application of composites is their inherent weakness in compressive strength when compared to the tensile properties of the same material. Furthermore, these airframe designs typically contain many bolted or riveted joints, as well as electrical and hydraulic control lines. These applications produce areas of stress concentration, and thus, further complicate the compression failure problem. Open hole compression failures which represent a typical failure mode for composite materials are addressed.

  2. Exploration of spin state and exchange integral of cobalt ions in stoichiometric ZnCo{sub 2}O{sub 4} spinel oxides

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Che, Xiangli; Li, Liping; Li, Guangshe, E-mail: guangshe@fjirsm.ac.cn

    2016-04-04

    This work reports on spin state and exchange integral of cobalt ions in stoichiometric ZnCo{sub 2}O{sub 4} nanoparticles with varying particle size from about 24 to 105 nm. Cobalt ions in ZnCo{sub 2}O{sub 4} nanoparticles are present as trivalence in mixed spin state. The effective magnetic moment is distributed in the range of 2.1 ∼ 1.31 μ{sub B} at room temperature with coarsening of nanoparticles. Further, it is demonstrated that stoichiometric ZnCo{sub 2}O{sub 4} undergoes a magnetic transition from paramagnetism to antiferromagnetism with decrease of temperature, showing a transition temperature of about 5 K. The standard molar entropy and enthalpy for 24 nm ZnCo{sub 2}O{sub 4}more » are 170.6 ± 1.7 J K{sup −1} mol{sup −1} and 28.2 ± 0.3 kJ mol{sup −1} at 298.15 K, respectively. Based on the heat capacity data, the exchange integral is determined to be 4.16 × 10{sup −22} J. The results report here are really important for further understanding the magnetic and electronic properties of spinel oxides.« less

  3. Sharp Truncation of an Electric Field: An Idealized Model That Warrants Caution

    ERIC Educational Resources Information Center

    Tu, Hong; Zhu, Jiongming

    2016-01-01

    In physics, idealized models are often used to simplify complex situations. The motivation of the idealization is to make the real complex system tractable by adopting certain simplifications. In this treatment some unnecessary, negligible aspects are stripped away (so-called Aristotelian idealization), or some deliberate distortions are involved…

  4. Caste and Choice: The Influence of Developmental Idealism on Marriage Behavior

    PubMed Central

    Allendorf, Keera; Thornton, Arland

    2015-01-01

    Is young people’s marriage behavior determined by their socioeconomic characteristics or their endorsement of developmental idealism? This article addresses this question using a unique, longitudinal data set from Nepal and provides the first individual-level test of developmental idealism theory. We find that unmarried individuals with greater endorsement of developmental idealism in 2008 were more likely by 2012 to choose their own spouse, including a spouse of a different caste, rather than have an arranged marriage. Those with salaried work experience were also less likely to have arranged marriages, but urban proximity and education were not significant. We conclude that both developmental idealism and socioeconomic characteristics influence marriage and their influences are largely independent. PMID:26430712

  5. Advertising, Social Epistemic, and Argumentation in the Composition Class.

    ERIC Educational Resources Information Center

    Turner, Brian

    1998-01-01

    Makes a case for using advertising as the common subject matter in a composition course, and for analyzing advertisements as a means of teaching argumentation. Discusses seeking a social-epistemic curriculum in the heterogeneous writing class. Shows why the close analysis of print advertisements provides an ideal opportunity to discuss questions…

  6. Neurocultural evidence that ideal affect match promotes giving

    PubMed Central

    Park, BoKyung; Blevins, Elizabeth; Knutson, Brian

    2017-01-01

    Abstract Why do people give to strangers? We propose that people trust and give more to those whose emotional expressions match how they ideally want to feel (“ideal affect match”). European Americans and Koreans played multiple trials of the Dictator Game with recipients who varied in emotional expression (excited, calm), race (White, Asian) and sex (male, female). Consistent with their culture’s valued affect, European Americans trusted and gave more to excited than calm recipients, whereas Koreans trusted and gave more to calm than excited recipients. These findings held regardless of recipient race and sex. We then used fMRI to probe potential affective and mentalizing mechanisms. Increased activity in the nucleus accumbens (associated with reward anticipation) predicted giving, as did decreased activity in the right temporo-parietal junction (rTPJ; associated with reduced belief prediction error). Ideal affect match decreased rTPJ activity, suggesting that people may trust and give more to strangers whom they perceive to share their affective values. PMID:28379542

  7. Reported Effects of Masculine Ideals on Gay Men.

    PubMed

    Sánchez, Francisco J; Greenberg, Stefanie T; Liu, William Ming; Vilain, Eric

    2009-01-01

    This exploratory study used consensual qualitative research methodology (Hill et al., 2005) to analyze what gay men associate with masculinity and femininity, how they feel masculine ideals affect their self-image, and how masculine ideals affect their same-sex relationships. Written responses were collected from 547 self-identified gay men in the U.S. via an Internet-based survey. Findings supported previous reports that perceptions of gender roles among gay men appear based on masculine and feminine stereotypes. Additionally, more adverse versus positive effects on self-image and same-sex romantic relationships were reported including difficulty being emotional and affectionate, pressure to be physically attractive, and pressure to appear masculine in order to be accepted by society and to be seen as desirable by other gay men. While research on gay men's experience with masculinity continues, psychologists should consider the possible influence of traditional masculine ideals when conceptualizing their gay male clients.

  8. Reported Effects of Masculine Ideals on Gay Men

    PubMed Central

    Sánchez, Francisco J.; Greenberg, Stefanie T.; Liu, William Ming; Vilain, Eric

    2010-01-01

    This exploratory study used consensual qualitative research methodology (Hill et al., 2005) to analyze what gay men associate with masculinity and femininity, how they feel masculine ideals affect their self-image, and how masculine ideals affect their same-sex relationships. Written responses were collected from 547 self-identified gay men in the U.S. via an Internet-based survey. Findings supported previous reports that perceptions of gender roles among gay men appear based on masculine and feminine stereotypes. Additionally, more adverse versus positive effects on self-image and same-sex romantic relationships were reported including difficulty being emotional and affectionate, pressure to be physically attractive, and pressure to appear masculine in order to be accepted by society and to be seen as desirable by other gay men. While research on gay men’s experience with masculinity continues, psychologists should consider the possible influence of traditional masculine ideals when conceptualizing their gay male clients. PMID:20628534

  9. Generic Evolution and Downward Coupling of Sudden Stratospheric Warmings in an Idealized GCM

    NASA Astrophysics Data System (ADS)

    Jucker, M.

    2016-12-01

    This work examines the life cycle of Sudden Stratospheric Warmings (SSWs) from composites of a large number of events. The events are sampled from idealized General Circulation Model (GCM) integrations, and form a database of several hundred major, displacement, splitting, and weak vortex events. It is shown that except for a few details, the generic zonal mean evolution does not depend on the definition used to detect SSWs. In all cases, the composites show the stratosphere in a positive annular mode phase prior to the events, and a barotropic response in the stratosphere at onset. There is a clear positive peak in upward Eliassen-Palm (EP) flux prior to the onset date in the stratosphere, and a much weaker peak in the troposphere, making the evolution more consistent with the picture of the stratosphere acting as a variable filter of tropospheric EP flux, rather than SSWs being forced by a strong `burst' in the troposphere. When comparing composites of SSWs from the database with apparent influence at the surface (downward `propagating') to those without such influence, the only significant differences are a somewhat more barotropic response at the onset date and longer persistence in the lower stratosphere after the onset for propagating SSWs. There is no significant difference in EP flux between propagating and non-propagating events, and none of the here considered definitions shows a particular skill in selecting propagating events.

  10. Structural arrest in an ideal gas.

    PubMed

    van Ketel, Willem; Das, Chinmay; Frenkel, Daan

    2005-04-08

    We report a molecular dynamics study of a simple model system that has the static properties of an ideal gas, yet exhibits nontrivial "glassy" dynamics behavior at high densities. The constituent molecules of this system are constructs of three infinitely thin hard rods of length L, rigidly joined at their midpoints. The crosses have random but fixed orientation. The static properties of this system are those of an ideal gas, and its collision frequency can be computed analytically. For number densities NL(3)/V>1, the single-particle diffusivity goes to zero. As the system is completely structureless, standard mode-coupling theory cannot describe the observed structural arrest. Nevertheless, the system exhibits many dynamical features that appear to be mode-coupling-like. All high-density incoherent intermediate scattering functions collapse onto master curves that depend only on the wave vector.

  11. Tooling Foam for Structural Composite Applications

    NASA Technical Reports Server (NTRS)

    DeLay, Tom; Smith, Brett H.; Ely, Kevin; MacArthur, Doug

    1998-01-01

    Tooling technology applications for composite structures fabrication have been expanded at MSFC's Productivity Enhancement Complex (PEC). Engineers from NASA/MSFC and Lockheed Martin Corporation have developed a tooling foam for use in composite materials processing and manufacturing that exhibits superior thermal and mechanical properties in comparison with other tooling foam materials. This tooling foam is also compatible with most preimpregnated composite resins such as epoxy, bismaleimide, phenolic and their associated cure cycles. MARCORE tooling foam has excellent processability for applications requiring either integral or removable tooling. It can also be tailored to meet the requirements for composite processing of parts with unlimited cross sectional area. A shelf life of at least six months is easily maintained when components are stored between 50F - 70F. The MARCORE tooling foam system is a two component urethane-modified polyisocyanurate, high density rigid foam with zero ozone depletion potential. This readily machineable, lightweight tooling foam is ideal for composite structures fabrication and is dimensionally stable at temperatures up to 350F and pressures of 100 psi.

  12. Tempting Fate or Inviting Happiness? Unrealistic idealization prevents the decline of marital satisfaction

    PubMed Central

    Murray, Sandra L.; Griffin, Dale W.; Derrick, Jaye L.; Harris, Brianna; Aloni, Maya; Leder, Sadie

    2014-01-01

    The authors examine whether unrealistically viewing a romantic partner as the image of one’s ideal partner accelerates or slows declines in marital satisfaction among newlyweds. A longitudinal study linked unrealistic idealization at the point of marriage to changes in satisfaction over the first three years of marriage. Overall, satisfaction declined markedly, consistent with past research. However, seeing a less-than-ideal partner as a reflection of one’s ideals predicted a certain level of immunity to the corrosive effects of time: People who initially idealized their partner highly experienced no declines in satisfaction. The obtained benefits of idealization remained in analyses that separately controlled for the positivity of partner perceptions and the possibility that better adjusted people might be in better relationships. PMID:21467549

  13. Critical Thinking and Educational Ideal

    ERIC Educational Resources Information Center

    Liu, Qian

    2007-01-01

    Critical thinking, as an educational trend, has been much discussed and proposed nowadays. In this paper, an analysis is made on the gap between our present educational practice and educational ideal from three different aspects, that is, the content, the manner and the one-sidedness of our teaching. It's observed that there is still a long way to…

  14. Stoichiometric titanium dioxide ion implantation in AISI 304 stainless steel for corrosion protection

    NASA Astrophysics Data System (ADS)

    Hartwig, A.; Decker, M.; Klein, O.; Karl, H.

    2015-12-01

    The aim of this study is to evaluate the applicability of highly chemically inert titanium dioxide synthesized by ion beam implantation for corrosion protection of AISI 304 stainless steel in sodium chloride solution. More specifically, the prevention of galvanic corrosion between carbon-fiber reinforced plastic (CFRP) and AISI 304 was investigated. Corrosion performance of TiO2 implanted AISI 304 - examined for different implantation and annealing parameters - is strongly influenced by implantation fluence. Experimental results show that a fluence of 5 × 1016 cm-2 (Ti+) and 1 × 1017 cm-2 (O+) is sufficient to prevent pitting corrosion significantly, while galvanic corrosion with CFRP can already be noticeably reduced by an implantation fluence of 5 × 1015 cm-2 (Ti+) and 1 × 1016 cm-2 (O+). Surface roughness, implantation energy and annealing at 200 °C and 400 °C show only little influence on the corrosion behavior. TEM analysis indicates the existence of stoichiometric TiO2 inside the steel matrix for medium fluences and the formation of a separated metal oxide layer for high fluences.

  15. Stoichiometric homeostasis predicts plant species dominance, temporal stability, and responses to global change.

    PubMed

    Yu, Qiang; Wilcox, Kevin; La Pierre, Kimberly; Knapp, Alan K; Han, Xingguo; Smith, Melinda D

    2015-09-01

    Why some species are consistently more abundant than others, and predicting how species will respond to global change, are fundamental questions in ecology. Long-term observations indicate that plant species with high stoichiometric homeostasis for nitrogen (HN), i.e., the ability to decouple foliar N levels from variation in soil N availability, were more common and stable through time than low-HN species in a central U.S. grassland. However, with nine years of nitrogen addition, species with high H(N) decreased in abundance, while those with low H(N) increased in abundance. In contrast, in climate change experiments simulating a range of forecast hydrologic changes, e.g., extreme drought (two years), increased rainfall variability (14 years), and chronic increases in rainfall (21 years), plant species with the highest H(N) were least responsive to changes in soil water availability. These results suggest that H(N) may be predictive of plant species success and stability, and how plant species and ecosystems will respond to global-change-driven alterations in resource availability.

  16. Turboprop IDEAL: a motion-resistant fat-water separation technique.

    PubMed

    Huo, Donglai; Li, Zhiqiang; Aboussouan, Eric; Karis, John P; Pipe, James G

    2009-01-01

    Suppression of the fat signal in MRI is very important for many clinical applications. Multi-point water-fat separation methods, such as IDEAL (Iterative Decomposition of water and fat with Echo Asymmetry and Least-squares estimation), can robustly separate water and fat signal, but inevitably increase scan time, making separated images more easily affected by patient motions. PROPELLER (Periodically Rotated Overlapping ParallEL Lines with Enhanced Reconstruction) and Turboprop techniques offer an effective approach to correct for motion artifacts. By combining these techniques together, we demonstrate that the new TP-IDEAL method can provide reliable water-fat separation with robust motion correction. The Turboprop sequence was modified to acquire source images, and motion correction algorithms were adjusted to assure the registration between different echo images. Theoretical calculations were performed to predict the optimal shift and spacing of the gradient echoes. Phantom images were acquired, and results were compared with regular FSE-IDEAL. Both T1- and T2-weighted images of the human brain were used to demonstrate the effectiveness of motion correction. TP-IDEAL images were also acquired for pelvis, knee, and foot, showing great potential of this technique for general clinical applications.

  17. Hybrid normed ideal perturbations of n-tuples of operators I

    NASA Astrophysics Data System (ADS)

    Voiculescu, Dan-Virgil

    2018-06-01

    In hybrid normed ideal perturbations of n-tuples of operators, the normed ideal is allowed to vary with the component operators. We begin extending to this setting the machinery we developed for normed ideal perturbations based on the modulus of quasicentral approximation and an adaptation of our non-commutative generalization of the Weyl-von Neumann theorem. For commuting n-tuples of hermitian operators, the modulus of quasicentral approximation remains essentially the same when Cn- is replaced by a hybrid n-tuple Cp1,…- , … , Cpn- , p1-1 + ⋯ + pn-1 = 1. The proof involves singular integrals of mixed homogeneity.

  18. Health care market deviations from the ideal market.

    PubMed

    Mwachofi, Ari; Al-Assaf, Assaf F

    2011-08-01

    A common argument in the health policy debate is that market forces allocate resources efficiently in health care, and that government intervention distorts such allocation. Rarely do those making such claims state explicitly that the market they refer to is an ideal in economic theory which can only exist under very strict conditions. This paper explores the strict conditions necessary for that ideal market in the context of health care as a means of examining the claim that market forces do allocate resources efficiently in health care.

  19. Idealness and similarity in goal-derived categories: a computational examination.

    PubMed

    Voorspoels, Wouter; Storms, Gert; Vanpaemel, Wolf

    2013-02-01

    The finding that the typicality gradient in goal-derived categories is mainly driven by ideals rather than by exemplar similarity has stood uncontested for nearly three decades. Due to the rather rigid earlier implementations of similarity, a key question has remained--that is, whether a more flexible approach to similarity would alter the conclusions. In the present study, we evaluated whether a similarity-based approach that allows for dimensional weighting could account for findings in goal-derived categories. To this end, we compared a computational model of exemplar similarity (the generalized context model; Nosofsky, Journal of Experimental Psychology. General 115:39-57, 1986) and a computational model of ideal representation (the ideal-dimension model; Voorspoels, Vanpaemel, & Storms, Psychonomic Bulletin & Review 18:1006-114, 2011) in their accounts of exemplar typicality in ten goal-derived categories. In terms of both goodness-of-fit and generalizability, we found strong evidence for an ideal approach in nearly all categories. We conclude that focusing on a limited set of features is necessary but not sufficient to account for the observed typicality gradient. A second aspect of ideal representations--that is, that extreme rather than common, central-tendency values drive typicality--seems to be crucial.

  20. Umbilical hernia repair with mesh: identifying effectors of ideal outcomes.

    PubMed

    Colavita, Paul D; Belyansky, Igor; Walters, Amanda L; Zemlyak, Alla Y; Lincourt, Amy E; Heniford, B Todd; Augenstein, Vedra A

    2014-09-01

    Quality of life has become an important focus for improvement in hernia repair. The International Hernia Mesh Registry was queried. The Carolinas Comfort Scale quantitated quality of life at 1-month, 6-month, and annual follow-up. Scores of 0 (completely asymptomatic) in all categories without recurrence defined an ideal outcome. The analysis consisted of 363 umbilical hernia repairs; 18.7% were laparoscopic. Demographics included age of 51.5 ± 13.8 years, 24.5% were female, and the average body mass index was 30.63 ± 5.9 kg/m(2). Mean defect size was 4.3 ± 3.1 cm(2). Mean follow-up was 18.2 months. Absent/minimal preoperative symptoms were predictive of ideal outcome at all time points and increasing age was predictive at 6 months and 1 year. At 6 months, the use of fixation sutures alone versus tacks (odds ratio 14.1) predicted ideal outcome. Ideal outcomes are dependent on both patient-specific and operative factors. The durable, ideal outcome in umbilical hernia repair is most likely in an older, asymptomatic patient who undergoes mesh fixation with permanent suture. Copyright © 2014 Elsevier Inc. All rights reserved.

  1. Titanium diboride-chromium diboride-yttrium titanium oxide ceramic composition and a process for making the same

    DOEpatents

    Holcombe, Cressie E.; Dykes, Norman L.

    1991-01-01

    A ceramic composition is described. The ceramic composition consists essentially of from about 84 to 96 w/o titanium diboride, from about 1 to 9 w/o chromium diboride, and from about 3 to about 15 w/o yttrium-titanium-oxide. A method of making the ceramic composition is also described. The method of making the ceramic composition comprises the following steps: Step 1--A consolidated body containing stoichiometric quantities of titanium diboride and chromium diboride is provided. Step 2--The consolidated body is enclosed in and in contact with a thermally insulated package of yttria granules having a thickness of at least 0.5 inches. Step 3--The consolidated body enclosed in the thermally insulated package of yttria granules is heated in a microwave oven with microwave energy to a temperature equal to or greater than 1,900 degrees centigrade to sinter and uniformly disperse yttria particles having a size range from about 1 to about 12 microns throughout the consolidated body forming a densified body consisting essentially of titanium diboride, chromium diboride, and yttrium-titanium-oxide. The resulting densified body has enhanced fracture toughness and hardness.

  2. Personality traits and appearance-ideal internalization: Differential associations with body dissatisfaction and compulsive exercise.

    PubMed

    Martin, Shelby J; Racine, Sarah E

    2017-12-01

    Thin-ideal internalization is a robust risk factor for body dissatisfaction and eating pathology. Conversely, athletic-ideal internalization is often unrelated to body dissatisfaction, but predicts compulsive exercise (i.e., rigid, rule-driven exercise that is continued despite adverse consequences). Distinct personality traits could relate to internalization of different appearance ideals, which may be associated with divergent eating disorder outcomes. Past research has shown that neuroticism is related to body dissatisfaction, whereas extraversion and conscientiousness have been associated with regular and problematic exercise. The current study examined associations among personality traits (i.e., neuroticism, extraversion, conscientiousness), appearance-ideal internalization (i.e., thin- and athletic-ideal), and eating disorder cognitions/behaviors (i.e., body dissatisfaction, compulsive exercise) among 531 college men and women. Moreover, we tested whether appearance-ideal internalization mediated the relationships between personality traits with body dissatisfaction and compulsive exercise. As expected, body dissatisfaction was positively related to neuroticism, and compulsive exercise was positively associated with extraversion. Thin-ideal internalization positively correlated with neuroticism, athletic-ideal internalization positively correlated with conscientiousness, and both thin- and athletic-ideal internalization were positively related to extraversion. After controlling for gender, body mass index, the other appearance-ideal internalization, and the remaining personality traits, the indirect effects of both neuroticism and extraversion on body dissatisfaction through thin-ideal internalization were significant. Extraversion and conscientiousness were indirectly related to compulsive exercise through athletic-ideal internalization, whereas the indirect effect of neuroticism was dependent on covariates. As such, personality traits may be related to

  3. Ideal GLM-MHD: About the entropy consistent nine-wave magnetic field divergence diminishing ideal magnetohydrodynamics equations

    NASA Astrophysics Data System (ADS)

    Derigs, Dominik; Winters, Andrew R.; Gassner, Gregor J.; Walch, Stefanie; Bohm, Marvin

    2018-07-01

    The paper presents two contributions in the context of the numerical simulation of magnetized fluid dynamics. First, we show how to extend the ideal magnetohydrodynamics (MHD) equations with an inbuilt magnetic field divergence cleaning mechanism in such a way that the resulting model is consistent with the second law of thermodynamics. As a byproduct of these derivations, we show that not all of the commonly used divergence cleaning extensions of the ideal MHD equations are thermodynamically consistent. Secondly, we present a numerical scheme obtained by constructing a specific finite volume discretization that is consistent with the discrete thermodynamic entropy. It includes a mechanism to control the discrete divergence error of the magnetic field by construction and is Galilean invariant. We implement the new high-order MHD solver in the adaptive mesh refinement code FLASH where we compare the divergence cleaning efficiency to the constrained transport solver available in FLASH (unsplit staggered mesh scheme).

  4. Teachers' Ethnotheories of the "Ideal Student" in Five Western Cultures

    ERIC Educational Resources Information Center

    Harkness, Sara; Blom, Marjolijn; Oliva, Alfredo; Moscardino, Ughetta; Zylicz, Piotr Olaf; Bermudez, Moises Rios; Feng, Xin; Carrasco-Zylicz, Agnieszka; Axia, Giovanna; Super, Charles M.

    2007-01-01

    This paper explores teachers' ethnotheories of the "ideal student" in five western societies: Italy, The Netherlands, Poland, Spain, and the US. Quantitative and qualitative methods are used to derive culture-specific profiles of the "ideal student" as described by kindergarten and primary school teachers in semi-structured…

  5. Thermodynamics of an ideal generalized gas: I. Thermodynamic laws.

    PubMed

    Lavenda, B H

    2005-11-01

    The equations of state for an ideal relativistic, or generalized, gas, like an ideal quantum gas, are expressed in terms of power laws of the temperature. In contrast to an ideal classical gas, the internal energy is a function of volume at constant temperature, implying that the ideal generalized gas will show either attractive or repulsive interactions. This is a necessary condition in order that the third law be obeyed and for matter to have an electromagnetic origin. The transition from an ideal generalized to a classical gas occurs when the two independent solutions of the subsidiary equation to Lagrange's equation coalesce. The equation of state relating the pressure to the internal energy encompasses the full range of cosmological scenarios, from the radiation to the matter dominated universes and finally to the vacuum energy, enabling the coefficient of proportionality, analogous to the Grüeisen ratio, to be interpreted in terms of the degrees of freedom related to the temperature exponents of the internal energy and the absolute temperature expressed in terms of a power of the empirical temperature. The limit where these exponents merge is shown to be the ideal classical gas limit. A corollary to Carnot's theorem is proved, asserting that the ratio of the work done over a cycle to the heat absorbed to increase the temperature at constant volume is the same for all bodies at the same volume. As power means, the energy and entropy are incomparable, and a new adiabatic potential is introduced by showing that the volume raised to a characteristic exponent is also the integrating factor for the quantity of heat so that the second law can be based on the property that power means are monotonically increasing functions of their order. The vanishing of the chemical potential in extensive systems implies that energy cannot be transported without matter and is equivalent to the condition that Clapeyron's equation be satisfied.

  6. Electronic tuning of the transport properties of off-stoichiometric Pb{sub x}Sn{sub 1−x}Te thermoelectric alloys by Bi{sub 2}Te{sub 3} doping

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Guttmann, Gilad M.; Dadon, David; Gelbstein, Yaniv

    2015-08-14

    The recent energy demands affected by the dilution of conventional energy resources and the growing awareness of environmental considerations had motivated many researchers to seek for novel renewable energy conversion methods. Thermoelectric direct conversion of thermal into electrical energies is such a method, in which common compositions include IV-VI semiconducting compounds (e.g., PbTe and SnTe) and their alloys. For approaching practical thermoelectric devices, the current research is focused on electronic optimization of off-stoichiometric p-type Pb{sub x}Sn{sub 1−x}Te alloys by tuning of Bi{sub 2}Te{sub 3} doping and/or SnTe alloying levels, while avoiding the less mechanically favorable Na dopant. It was shownmore » that upon such doping/alloying, higher ZTs, compared to those of previously reported undoped Pb{sub 0.5}Sn{sub 0.5}Te alloy, were obtained at temperatures lower than 210–340 °C, depending of the exact doping/alloying level. It was demonstrated that upon optimal grading of the carrier concentration, a maximal thermoelectric efficiency enhancement of ∼38%, compared to that of an undoped material, is expected.« less

  7. Quantification of non-ideal explosion violence with a shock tube

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Jackson, Scott I; Hill, Larry G

    There is significant interest in quantifying the blast violence associated with various nonideal explosions. Such data is essential to evaluate the damage potential of both explosive cookoff and terrorist explosive scenarios. We present a technique designed to measure the source energy associated with a non-ideal, asymmetrical, and three-dimensional explosion. A tube is used to confine and focus energy from a blast event into a one-dimensional, quasi-planar shock front. During propagation along the length of the tube, the wave is allowed to shocksteepen into a more ideal form. Pressure transducers then measure the shock overpressure as a function of the distancemore » from the source. One-dimensional blast scaling theory allows calculation of the source energy from this data. This small-scale test method addresses cost and noise concerns as well as boosting and symmetry issues associated with large-scale, three-dimensional, blast arena tests. Results from both ideal explosives and non-ideal explosives are discussed.« less

  8. Developmental Idealism and Cultural Models of the Family in Malawi

    PubMed Central

    Pierotti, Rachael S.; Young-DeMarco, Linda; Watkins, Susan

    2014-01-01

    This paper examines the extent to which developmental idealism has been disseminated in Malawi. Developmental idealism is a set of beliefs and values about development and the relationships between development and family structures and behavior. Developmental idealism states that attributes of societies and families defined as modern are better than attributes defined as traditional, that modern societies help produce modern families, that modern families facilitate the achievement of modern societies, and that the future will bring family change in the direction of modernity. Previous research has demonstrated that knowledge of developmental idealism is widespread in many places around the world, but provides little systematic data about it in sub-Saharan Africa or how knowledge of it is associated with certain demographic characteristics in that region. In this paper, we address this issue by examining whether ordinary people in two settings in Malawi, a sub-Saharan African country, have received and understood messages that are intended to associate development with certain types of family forms and family behaviors. We then examine associations between demographic characteristics and developmental idealism to investigate possible mechanisms linking global discourse about development to the grassroots. We analyze data collected in face-to-face surveys from two samples of Malawian men in 2009 and 2010, one rural, the other in a low-to-medium income neighborhood of a city. Our analysis of these survey data shows considerable evidence that many developmental idealism beliefs have been spread in that country and that education has positive effects on beliefs in the association between development and family attributes. We also find higher levels of developmental idealism awareness in the urban sample than we do in the rural sample, but once dissimilarities in education and wealth between the two samples are controlled, awareness levels no longer differed between

  9. Health Care Market Deviations from the Ideal Market

    PubMed Central

    Mwachofi, Ari; Al-Assaf, Assaf F.

    2011-01-01

    A common argument in the health policy debate is that market forces allocate resources efficiently in health care, and that government intervention distorts such allocation. Rarely do those making such claims state explicitly that the market they refer to is an ideal in economic theory which can only exist under very strict conditions. This paper explores the strict conditions necessary for that ideal market in the context of health care as a means of examining the claim that market forces do allocate resources efficiently in health care. PMID:22087373

  10. Catalytic EGR-Loop Reforming for High Efficiency in a Stoichiometric SI Engine through TCR and Dilution Limit Extension. 1. Catalyst Performance and Fuel Effects

    DOE PAGES

    Chang, Yan; Szybist, James P.; Pihl, Josh A.; ...

    2017-12-19

    The use of fuel reformate from catalytic processes is known to have beneficial effects on the spark-ignited (SI) combustion process through enhanced dilution tolerance and decreased combustion duration, but in many cases reformate generation can incur a significant fuel penalty. Here, in this two-part investigation, we demonstrate that efficient catalytic fuel reforming can result in improved brake engine efficiency while maintaining stoichiometric exhaust under the right conditions. In part one of this investigation, we used a combination of thermodynamic equilibrium calculations and experimental fuel catalytic reforming measurements on an engine to characterize the best possible reforming performance and energetics overmore » a range of equivalence ratios and O 2 concentrations. Ideally, one might expect the highest levels of thermochemical recuperation for the highest catalyst equivalence ratios. However, reforming under these conditions is highly endothermic, and the available enthalpy for reforming is constrained. Thus for relatively high equivalence ratios, more methane and less H 2 and CO are produced. Our experiments revealed that this suppression of H 2 and CO could be countered by adding small amounts of O 2, yielding as much as 15 vol % H 2 at the catalyst outlet for 4 < Φ catalyst < 7 under quasi-steady-state conditions. Under these conditions the H 2 and CO yields were highest and there was significant water consumption, confirming the presence of steam reforming reactions. Analyses of the experimental catalyst measurements indicated the possibility of both endothermic and exothermic reaction stages and global reaction rates sufficient to enable the utilization of higher space velocities than those employed in our experiments. Finally, in a companion paper detailing part two of this investigation, we present results for the engine dilution tolerance and brake engine efficiency impacts of the reforming levels achieved.« less

  11. Catalytic EGR-Loop Reforming for High Efficiency in a Stoichiometric SI Engine through TCR and Dilution Limit Extension. 1. Catalyst Performance and Fuel Effects

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Chang, Yan; Szybist, James P.; Pihl, Josh A.

    The use of fuel reformate from catalytic processes is known to have beneficial effects on the spark-ignited (SI) combustion process through enhanced dilution tolerance and decreased combustion duration, but in many cases reformate generation can incur a significant fuel penalty. Here, in this two-part investigation, we demonstrate that efficient catalytic fuel reforming can result in improved brake engine efficiency while maintaining stoichiometric exhaust under the right conditions. In part one of this investigation, we used a combination of thermodynamic equilibrium calculations and experimental fuel catalytic reforming measurements on an engine to characterize the best possible reforming performance and energetics overmore » a range of equivalence ratios and O 2 concentrations. Ideally, one might expect the highest levels of thermochemical recuperation for the highest catalyst equivalence ratios. However, reforming under these conditions is highly endothermic, and the available enthalpy for reforming is constrained. Thus for relatively high equivalence ratios, more methane and less H 2 and CO are produced. Our experiments revealed that this suppression of H 2 and CO could be countered by adding small amounts of O 2, yielding as much as 15 vol % H 2 at the catalyst outlet for 4 < Φ catalyst < 7 under quasi-steady-state conditions. Under these conditions the H 2 and CO yields were highest and there was significant water consumption, confirming the presence of steam reforming reactions. Analyses of the experimental catalyst measurements indicated the possibility of both endothermic and exothermic reaction stages and global reaction rates sufficient to enable the utilization of higher space velocities than those employed in our experiments. Finally, in a companion paper detailing part two of this investigation, we present results for the engine dilution tolerance and brake engine efficiency impacts of the reforming levels achieved.« less

  12. Thin-ideal internalization: How much is too much?

    PubMed

    Schaefer, Lauren M; Burke, Natasha L; Thompson, J Kevin

    2018-03-16

    Internalization of the thin-ideal is a risk factor for eating disorders that frequently persists into recovery and increases patient risk for relapse. Addressing thin-ideal internalization as a core element of eating disorder prevention and treatment produces significant reductions in eating pathology. However, research has not yet quantified levels of thin-ideal internalization that may signal increased versus decreased risk for disordered eating. To address this gap in the literature, receiver operating characteristic (ROC) curve analysis was used to identify a thin-ideal internalization cutoff score that signified clinically-meaningful eating disorder pathology. 787 college women (age M = 20.17, SD = 2.41; BMI M = 23.58, SD = 5.29) were classified as "healthy" (N = 717) or those with significant disordered eating (N = 70) using established clinical cutoffs for the Eating Disorder Examination-Questionnaire. ROC curve analysis was used to test the performance of the Sociocultural Attitudes Towards Appearance Questionnaire-4 (SATAQ-4) Internalization: Thin/Low Body Fat subscale in predicting disordered eating status, and to identify a cutoff score that maximized sensitivity and specificity to discriminate between healthy and disordered eating samples. Mean SATAQ-4 internalization scores were 3.29 (SD = 0.92) and 4.27 (SD = 0.62) for healthy and disordered eating participants, respectively. The SATAQ-4 internalization scores were good predictors of disordered eating status (area under the curve = 0.81, 95% CI: 0.76-0.86). The optimal cutoff of 3.78 (measured on a 1-5 Likert scale) yielded a sensitivity of 0.81 and specificity of 0.64. Overall, results provide preliminary support for the discriminant validity of SATAQ-4 thin internalization scores and suggest that even moderate levels of thin-ideal internalization may be predictive of clinically-significant eating pathology. It may be important for prevention and intervention work to actively seek to reduce

  13. Nutrient recycling and the stoichiometric relationship among C, N, and P in Paleozoic anoxic sediments

    NASA Astrophysics Data System (ADS)

    Tuite, M. L., Jr.

    2016-12-01

    Remineralized organic N and P diffused into the water column from underlying anoxic sediments were important sources of macronutrients for primary production in shallow Paleozoic epicontinental seas. Ratios of total organic C to total N or P in ancient sediments that are greater than Redfield-like values are often cited as evidence for macronutrient recycling. We propose that the stoichiometric relationship among C, N, and P in anoxic Paleozoic sediments was mediated primarily by heterotrophic bacterial alkaline phosphatases. Bacterial heterotrophy in organic-rich anaerobic sediments is frequently limited by the availability of labile (low C/N) organic matter. In response, bacterial heterotrophs invest scarce C and N to produce alkaline phosphatases in order to alleviate labile organic matter limitation by hydrolysis of organophosphates. This suggests that sediment organic C/N may represent a threshold beyond which the investment of intracellular C and N in the production of alkaline phosphatase no longer results in a stoichiometrically favorable return on the investment. If this is the case, then C/P likely represents the point in the diagenesis of organic matter at which the effectiveness of alkaline phosphatase in procuring labile organic matter by remineralization of P is constrained by the lability of the organic matter itself. Because alkaline phosphatase activity is expressed in inverse proportion to the porewater concentration of phosphate, at a given distance from the terrestrial source of weathered P, an equilibrium determined by total phosphate influx results in consistent total P burial rates and consistent organic C/N values independent of the total organic content of the sediment. To account for consistent C/N in spite of variable total organic carbon at a given location, we propose that variations in the absolute abundance of organic C in organic-rich Devonian sediments were largely a function of the lipid content of algal primary producers. The

  14. Ideal Teaching: Exploring the Attributes of an "Ideal Teacher" in the Church Educational System for the Church of Jesus Christ of Latter-Day Saints

    ERIC Educational Resources Information Center

    Strader, Matthew W.

    2009-01-01

    The purpose of this study was to identify the profile of an ideal teacher for the Church Educational System (CES) for the Church of Jesus Christ of Latter-day Saints. This study surveyed 159 students, teachers, and administrators in order to find the characteristics perceived to be ideal in a CES teacher. The survey included 16 characteristics of…

  15. Your Ideal Silhouette. Courseware Evaluation for Vocational and Technical Education.

    ERIC Educational Resources Information Center

    Tierney, Margaret S.; And Others

    This courseware evaluation rates the "Your Ideal Silhouette" program developed by Your Image, Inc. This program (not contained in this document) uses the computer to identify figure faults and illustrate personalized corrective style lines to achieve the ideal silhouette. Part A describes the program in terms of subject area (textiles…

  16. The "Ideal Professor" and Gender Effects in Christian Higher Education

    ERIC Educational Resources Information Center

    Woods, Robert H., Jr.; Badzinski, Diane M.; Fritz, Janie M. Harden; Yeates, Sarah E.

    2012-01-01

    A survey was administered to 451 undergraduate students at a private liberal arts Christian university to identify students' perceptions of the ideal professor. The survey revealed that the ideal professor places great emphasis on the integration of faith and learning, is flexible (and even easy), maintains high academic standards, encourages…

  17. Joining of polymer composite materials

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Magness, F.H.

    1990-11-01

    Under ideal conditions load bearing structures would be designed without joints, thus eliminating a source of added weight, complexity and weakness. In reality the need for accessibility, repair, and inspectability, added to the size limitations imposed by the manufacturing process and transportation/assembly requirements mean that some minimum number of joints will be required in most structures. The designer generally has two methods for joining fiber composite materials, adhesive bonding and mechanical fastening. As the use of thermoplastic materials increases, a third joining technique -- welding -- will become more common. It is the purpose of this document to provide amore » review of the available sources pertinent to the design of joints in fiber composites. The primary emphasis is given to adhesive bonding and mechanical fastening with information coming from documentary sources as old as 1961 and as recent as 1989. A third, shorter section on composite welding is included in order to provide a relatively comprehensive treatment of the subject.« less

  18. Shifts in the Physiology and Stoichiometric Needs of Soil Microbial Communities from Subarctic Soils in Response to Warming: Icelandic Geothermal Gradients as a Model.

    NASA Astrophysics Data System (ADS)

    Marañón-Jiménez, S.; Soong, J.; Leblans, N. I. W.; Sigurdsson, B. D.; Peñuelas, J.; Richter, A.; Asensio, D.; Fransen, E.; Janssens, I. A.

    2017-12-01

    Large amounts of CO2 can be released to the atmosphere from a faster mineralization of soil organic matter at warmer temperatures, thus inducing climate change feedbacks. Specifically, soils at high northern latitudes store more than half of the global surface soil carbon and are particularly vulnerable to temperature-driven C losses, since they warm more rapidly. Alterations to the temperature sensitivity, physiological functioning and stoichiometric constrains of soil microorganisms in response to rising temperatures can play a key role in these soil carbon (C) losses. We present results of several incubation experiments using soils from geothermal soil temperature gradients in Iceland that have undergone a range of warming intensities for seven years, encompassing the full range of IPCC warming scenarios for the northern region. Soil microbes from warmed soils did not show changes in their temperature sensitivity at the physiological level. On the contrary, seven years of chronic soil warming provoked a permanent increase of microbial metabolic quotients (i.e., respiration per unit of biomass), and a subsequent reduction in the C retained in biomass as substrate became limiting. After the initial depletion of labile soil C, increasing energy demands for metabolic maintenance and resource acquisition at higher temperatures may have triggered permanent functional changes or community shifts towards increasing respiratory costs of soil decomposers. Pointing to this, microbial communities showed a strong C limitation even at ambient soil temperatures, obscuring any metabolic response to nitrogen and phosphorous additions. The tight C:N stoichiometric constrains of soil microbial communities and the strong C limitation for microbial biomass may lead to a reduced capacity of microbial N retention, explaining the equivalent soil C and N losses found in response to soil warming. These results highlight the need to incorporate potential changes in microbial physiological

  19. Stoichiometric control of lead chalcogenide nanocrystal solids to enhance their electronic and optoelectronic device performance.

    PubMed

    Oh, Soong Ju; Berry, Nathaniel E; Choi, Ji-Hyuk; Gaulding, E Ashley; Paik, Taejong; Hong, Sung-Hoon; Murray, Christopher B; Kagan, Cherie R

    2013-03-26

    We investigate the effects of stoichiometric imbalance on the electronic properties of lead chalcogenide nanocrystal films by introducing excess lead (Pb) or selenium (Se) through thermal evaporation. Hall-effect and capacitance-voltage measurements show that the carrier type, concentration, and Fermi level in nanocrystal solids may be precisely controlled through their stoichiometry. By manipulating only the stoichiometry of the nanocrystal solids, we engineer the characteristics of electronic and optoelectronic devices. Lead chalcogenide nanocrystal field-effect transistors (FETs) are fabricated at room temperature to form ambipolar, unipolar n-type, and unipolar p-type semiconducting channels as-prepared and with excess Pb and Se, respectively. Introducing excess Pb forms nanocrystal FETs with electron mobilities of 10 cm(2)/(V s), which is an order of magnitude higher than previously reported in lead chalcogenide nanocrystal devices. Adding excess Se to semiconductor nanocrystal solids in PbSe Schottky solar cells enhances the power conversion efficiency.

  20. High-Temperature Annealing as a Method for the Silicon Nanoclusters Growth in Stoichiometric Silicon Dioxide

    NASA Astrophysics Data System (ADS)

    Ivanova, E. V.; Dementev, P. A.; Sitnikova, A. A.; Aleksandrov, O. V.; Zamoryanskaya, M. V.

    2018-07-01

    A method for the growth of nanocomposite layers in stoichiometric amorphous silicon dioxide is proposed. It is shown that, after annealing at a temperature of 1150°C in nitrogen atmosphere, a layer containing silicon nanoclusters is formed. Silicon nanoclusters have a crystal structure and a size of 3-6 nm. In a film grown on a n-type substrate, a layer of silicon nanoclusters with a thickness of about 10 nm is observed. In the case of a film grown on a p-type substrate, a nanocomposite layer with a thickness of about 100 nm is observed. The difference in the formation of a nanocomposite layer in films on various substrates is associated with the doping of silicon dioxide with impurities from the substrate during the growth of the film. The formation of the nanocomposite layer was confirmed by transmission electron microscopy, XPS and local cathodoluminescence studies.

  1. Why the Kantian ideal survives medical learning curves, and why it matters.

    PubMed

    Brecher, B

    2006-09-01

    The "Kantian ideal" is often misunderstood as invoking individual autonomy rather than rational self legislation. Le Morvan and Stock's otherwise insightful discussion of "Medical learning curves and the Kantian ideal"--for example--draws the mistaken inference that that ideal is inconsistent with the realities of medical practice. But it is not. Rationally to be a patient entails accepting its necessary conditions.

  2. Developmental Idealism: The Cultural Foundations of World Development Programs

    PubMed Central

    Thornton, Arland; Dorius, Shawn F.; Swindle, Jeffrey

    2015-01-01

    This paper extends theory and research concerning cultural models of development beyond family and demographic matters to a broad range of additional factors, including government, education, human rights, daily social conventions, and religion. Developmental idealism is a cultural model—a set of beliefs and values—that identifies the appropriate goals of development and the ends for achieving these goals. It includes beliefs about positive cause and effect relationships among such factors as economic growth, educational achievement, health, and political governance, as well as strong values regarding many attributes, including economic growth, education, small families, gender equality, and democratic governance. This cultural model has spread from its origins among the elites of northwest Europe to elites and ordinary people throughout the world. Developmental idealism has become so entrenched in local, national, and global social institutions that it has now achieved a taken-for-granted status among many national elites, academics, development practitioners, and ordinary people around the world. We argue that developmental idealism culture has been a fundamental force behind many cultural clashes within and between societies, and continues to be an important cause of much global social change. We suggest that developmental idealism should be included as a causal factor in theories of human behavior and social change. PMID:26457325

  3. Neurocultural evidence that ideal affect match promotes giving.

    PubMed

    Park, BoKyung; Blevins, Elizabeth; Knutson, Brian; Tsai, Jeanne L

    2017-07-01

    Why do people give to strangers? We propose that people trust and give more to those whose emotional expressions match how they ideally want to feel ("ideal affect match"). European Americans and Koreans played multiple trials of the Dictator Game with recipients who varied in emotional expression (excited, calm), race (White, Asian) and sex (male, female). Consistent with their culture's valued affect, European Americans trusted and gave more to excited than calm recipients, whereas Koreans trusted and gave more to calm than excited recipients. These findings held regardless of recipient race and sex. We then used fMRI to probe potential affective and mentalizing mechanisms. Increased activity in the nucleus accumbens (associated with reward anticipation) predicted giving, as did decreased activity in the right temporo-parietal junction (rTPJ; associated with reduced belief prediction error). Ideal affect match decreased rTPJ activity, suggesting that people may trust and give more to strangers whom they perceive to share their affective values. © The Author (2017). Published by Oxford University Press.

  4. Perceptual thresholds for non-ideal diffuse field reverberation.

    PubMed

    Romblom, David; Guastavino, Catherine; Depalle, Philippe

    2016-11-01

    The objective of this study is to understand listeners' sensitivity to directional variations in non-ideal diffuse field reverberation. An ABX discrimination test was conducted using a semi-spherical 28-loudspeaker array; perceptual thresholds were estimated by systematically varying the level of a segment of loudspeakers for lateral, height, and frontal conditions. The overall energy was held constant using a gain compensation scheme. When compared to an ideal diffuse field, the perceptual threshold for detection is -2.5 dB for the lateral condition, -6.8 dB for the height condition, and -3.2 dB for the frontal condition. Measurements of the experimental stimuli were analyzed using a Head and Torso Simulator as well as with opposing cardioid microphones aligned on the three Cartesian axes. Additionally, opposing cardioid measurements made in an acoustic space demonstrate that level differences corresponding to the perceptual thresholds can be found in practice. These results suggest that non-ideal diffuse field reverberation may be a previously unrecognized component of spatial impression.

  5. Food Web Architecture and Basal Resources Interact to Determine Biomass and Stoichiometric Cascades along a Benthic Food Web

    PubMed Central

    Guariento, Rafael D.; Carneiro, Luciana S.; Caliman, Adriano; Leal, João J. F.; Bozelli, Reinaldo L.; Esteves, Francisco A.

    2011-01-01

    Understanding the effects of predators and resources on primary producers has been a major focus of interest in ecology. Within this context, the trophic cascade concept especially concerning the pelagic zone of lakes has been the focus of the majority of these studies. However, littoral food webs could be especially interesting because base trophic levels may be strongly regulated by consumers and prone to be light limited. In this study, the availability of nutrients and light and the presence of an omnivorous fish (Hyphessobrycon bifasciatus) were manipulated in enclosures placed in a humic coastal lagoon (Cabiúnas Lagoon, Macaé – RJ) to evaluate the individual and interactive effects of resource availability (nutrients and light) and food web configuration on the biomass and stoichiometry of periphyton and benthic grazers. Our findings suggest that light and nutrients interact to determine periphyton biomass and stoichiometry, which propagates to the consumer level. We observed a positive effect of the availability of nutrients on periphytic biomass and grazers' biomass, as well as a reduction of periphytic C∶N∶P ratios and an increase of grazers' N and P content. Low light availability constrained the propagation of nutrient effects on periphyton biomass and induced higher periphytic C∶N∶P ratios. The effects of fish presence strongly interacted with resource availability. In general, a positive effect of fish presence was observed for the total biomass of periphyton and grazer's biomass, especially with high resource availability, but the opposite was found for periphytic autotrophic biomass. Fish also had a significant effect on periphyton stoichiometry, but no effect was observed on grazers' stoichiometric ratios. In summary, we observed that the indirect effect of fish predation on periphyton biomass might be dependent on multiple resources and periphyton nutrient stoichiometric variation can affect consumers' stoichiometry. PMID:21789234

  6. Dissolution of aragonite-strontianite solid solutions in nonstoichiometric Sr (HCO3)2-Ca (HCO3)2-CO2-H2O solutions

    USGS Publications Warehouse

    Plummer, Niel; Busenberg, E.; Glynn, P.D.; Blum, A.E.

    1992-01-01

    Synthetic strontianite-aragonite solid-solution minerals were dissolved in CO2-saturated non-stoichiometric solutions of Sr(HCO3)2 and Ca(HCO3)2 at 25??C. The results show that none of the dissolution reactions reach thermodynamic equilibrium. Congruent dissolution in Ca(HCO3)2 solutions either attains or closely approaches stoichiometric saturation with respect to the dissolving solid. In Sr(HCO3)2 solutions the reactions usually become incongruent, precipitating a Sr-rich phase before reaching stoichiometric saturation. Dissolution of mechanical mixtures of solids approaches stoichiometric saturation with respect to the least stable solid in the mixture. Surface uptake from subsaturated bulk solutions was observed in the initial minutes of dissolution. This surficial phase is 0-10 atomic layers thick in Sr(HCO3)2 solutions and 0-4 layers thick in Ca(HCO3)2 solutions, and subsequently dissolves and/or recrystallizes, usually within 6 min of reaction. The initial transient surface precipitation (recrystallization) process is followed by congruent dissolution of the original solid which proceeds to stoichiometric saturation, or until the precipitation of a more stable Sr-rich solid. The compositions of secondary precipitates do not correspond to thermodynamic equilibrium or stoichiometric saturation states. X-ray photoelectron spectroscopy (XPS) measurements indicate the formation of solid solutions on surfaces of aragonite and strontianite single crystals immersed in Sr(HCO3)2 and Ca(HCO3)2 solutions, respectively. In Sr(HCO3)2 solutions, the XPS signal from the outer ~ 60 A?? on aragonite indicates a composition of 16 mol% SrCO3 after only 2 min of contact, and 14-18 mol% SrCO3 after 3 weeks of contact. The strontianite surface averages approximately 22 mol% CaCO3 after 2 min of contact with Ca(HCO3)2 solution, and is 34-39 mol% CaCO3 after 3 weeks of contact. XPS analysis suggests the surface composition is zoned with somewhat greater enrichment in the outer ~25

  7. Measuring explosive non-ideality

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Souers, P C

    1999-02-17

    The sonic reaction zone length may be measured by four methods: (1) size effect, (2) detonation front curvature, (3) crystal interface velocity and (4) in-situ gauges. The amount of data decreases exponentially from (1) to (4) with there being almost no gauge data for prompt detonation at steady state. The ease and clarity of obtaining the reaction zone length increases from (1) to (4). The method of getting the reaction zone length, , is described for the four methods. A measure of non-ideality is proposed: the reaction zone length divided by the cylinder radius. N = /R{sub o}.more » N = 0 for true ideality. It also decreases with increasing radius as it should. For N < 0.10, an equilibrium EOS like the JWL may be used. For N > 0.10, a time-dependent description is essential. The crystal experiment, which measures the particle velocity of an explosive-transparent material interface, is presently rising in importance. We examine the data from three experiments and apply: (1) an impedance correction that transfers the explosive C-J particle velocity to the corresponding value for the interface, and (2) multiplies the interface time by 3/4 to simulate the explosive speed of sound. The result is a reaction zone length comparable to those obtained by other means. A few explosives have reaction zones so small that the change of slope in the particle velocity is easily seen.« less

  8. The effect of priming materialism on women's responses to thin-ideal media.

    PubMed

    Ashikali, Eleni-Marina; Dittmar, Helga

    2012-12-01

    Consumer culture is characterized by two prominent ideals: the 'body perfect' and the material 'good life'. Although the impact of these ideals has been investigated in separate research literatures, no previous research has examined whether materialism is linked to women's responses to thin-ideal media. Data from several studies confirm that the internalization of materialistic and body-ideal values is positively linked in women. After developing a prime for materialism (N = 50), we present an experimental examination (N = 155) of the effects of priming materialism on women's responses to thin-ideal media, using multiple outcome measures of state body dissatisfaction. Priming materialism affects women's body dissatisfaction after exposure to thin media models, but differently depending on the dimension of body image measured. The two main novel findings are that (1) priming materialism heightens the centrality of appearance to women's self-concept and (2) priming materialism influences the activation of body-related self-discrepancies (BRSDs), particularly for highly materialistic women. Exposure to materialistic media has a clear influence on women's body image, with trait materialism a further vulnerability factor for negative exposure effects in response to idealized, thin media models. ©2011 The British Psychological Society.

  9. Noninteractive macroscopic reliability model for whisker-reinforced ceramic composites

    NASA Technical Reports Server (NTRS)

    Duffy, Stephen F.; Arnold, Steven M.

    1990-01-01

    Considerable research is underway in the field of material science focusing on incorporating silicon carbide whiskers into silicon nitride and alumina matrices. These composites show the requisite thermal stability and thermal shock resistance necessary for use as components in advanced gas turbines and heat exchangers. This paper presents a macroscopic noninteractive reliability model for whisker-reinforced ceramic composites. The theory is multiaxial and is applicable to composites that can be characterized as transversely isotropic. Enough processing data exists to suggest this idealization encompasses a significantly large class of fabricated components. A qualitative assessment of the model is made by presenting reliability surfaces in several different stress spaces and for different values of model parameters.

  10. Quantum cryptography with an ideal local relay

    NASA Astrophysics Data System (ADS)

    Spedalieri, Gaetana; Ottaviani, Carlo; Braunstein, Samuel L.; Gehring, Tobias; Jacobsen, Christian S.; Andersen, Ulrik L.; Pirandola, Stefano

    2015-10-01

    We consider two remote parties connected to a relay by two quantum channels. To generate a secret key, they transmit coherent states to the relay, where the states are subject to a continuous-variable (CV) Bell detection. We study the ideal case where Alice's channel is lossless, i.e., the relay is locally in her lab and the Bell detection is perfomed with unit efficiency. This configuration allows us to explore the optimal performances achievable by CV measurement-device-independent quantum key distribution. This corresponds to the limit of a trusted local relay, where the detection loss can be re-scaled. Our theoretical analysis is confirmed by an experimental simulation where 10-4 secret bits per use can potentially be distributed at 170km assuming ideal reconciliation.

  11. Self-guide framing and persuasion: responsibly increasing message processing to ideal levels.

    PubMed

    Evans, Lisa M; Petty, Richard E

    2003-03-01

    The current research examines the effect that framing persuasive messages in terms of self-guides (ideal vs. ought) has on the attitudes and cognitive responses of individuals with chronic ideal versus ought self-guides. The strength of participants' ideal and ought self-guides and the magnitude of participants' ideal and ought self-discrepancies were measured using a computerized reaction time program. One week later, participants read a persuasive message about a fictional breakfast product, framed in terms of either ideals or oughts. Matching framing to stronger self-guide led to enhanced message processing activity, especially among individuals who were low in need for cognition. Individuals who read messages framed to match their stronger self-guides paid more attention to argument quality, as reflected in their attitudes and cognitive responses. Messages with self-guide framing that matched individuals' stronger self-discrepancies did not have this effect on processing.

  12. A Darker Shade of Love: Machiavellianism and Positive Assortative Mating Based on Romantic Ideals

    PubMed Central

    Ináncsi, Tamás; Láng, András; Bereczkei, Tamás

    2016-01-01

    Machiavellianism is a personality trait that is characterized by manipulative and exploitative attitude toward others, lack of empathy, and a cynical view of human nature. In itself or as part of the Dark Triad it has been the target of several studies investigating romantic relations. Nevertheless, the relationship between Machiavellianism and romantic ideals has not been revealed yet. An undergraduate sample of 143 (92 females) with an average age of 19.83 years (SD = 1.51 years) filled out self-report measures of Machiavellianism (Mach-IV Scale) and romantic ideals (Ideal Standards Scale and NEO-FFI-IDEAL). According to our results, Machiavellianism correlated negatively with the importance of partner’s warmth-trustworthiness, extraversion, openness, agreeableness, and with the importance of intimacy and loyalty in their ideal relationships. Machiavellianism correlated positively with the ideal partner’s possession over status and resources. Explorative factor analysis revealed three components of ideal partner’s characteristics. Machiavellianism loaded significantly on two out of three components. Results are discussed with regard to Ideal Standards Model and the Big Five model of personality. PMID:27247697

  13. Ambivalent Sexism in Close Relationships: (Hostile) Power and (Benevolent) Romance Shape Relationship Ideals

    PubMed Central

    Lee, Tiane L.; Fiske, Susan T.; Glick, Peter; Chen, Zhixia

    2013-01-01

    Gender-based structural power and heterosexual dependency produce ambivalent gender ideologies, with hostility and benevolence separately shaping close-relationship ideals. The relative importance of romanticized benevolent versus more overtly power-based hostile sexism, however, may be culturally dependent. Testing this, northeast US (N=311) and central Chinese (N=290) undergraduates rated prescriptions and proscriptions (ideals) for partners and completed Ambivalent Sexism and Ambivalence toward Men Inventories (ideologies). Multiple regressions analyses conducted on group-specific relationship ideals revealed that benevolent ideologies predicted partner ideals, in both countries, especially for US culture’s romance-oriented relationships. Hostile attitudes predicted men’s ideals, both American and Chinese, suggesting both societies’ dominant-partner advantage. PMID:23914004

  14. Axisymmetric ideal MHD stellar wind flow

    NASA Technical Reports Server (NTRS)

    Heinemann, M.; Olbert, S.

    1978-01-01

    The ideal MHD equations are reduced to a single equation under the assumption of axisymmetric flow. A variational principle from which the equation is derivable is given. The characteristics of the equation are briefly discussed. The equation is used to rederive the theorem of Gussenhoven and Carovillano.

  15. Post-impact behavior of composite solid rocket motor cases

    NASA Technical Reports Server (NTRS)

    Highsmith, Alton L.

    1992-01-01

    In recent years, composite materials have seen increasing use in advanced structural applications because of the significant weight savings they offer when compared to more traditional engineering materials. The higher cost of composites must be offset by the increased performance that results from reduced structural weight if these new materials are to be used effectively. At present, there is considerable interest in fabricating solid rocket motor cases out of composite materials, and capitalizing on the reduced structural weight to increase rocket performance. However, one of the difficulties that arises when composite materials are used is that composites can develop significant amounts of internal damage during low velocity impacts. Such low velocity impacts may be encountered in routine handling of a structural component like a rocket motor case. The ability to assess the reduction in structural integrity of composite motor cases that experience accidental impacts is essential if composite rocket motor cases are to be certified for manned flight. The study described herein was an initial investigation of damage development and reduction of tensile strength in an idealized composite subjected to low velocity impacts.

  16. Compositional changes at the interface between thorium-doped uranium dioxide and zirconium due to high-temperature annealing

    NASA Astrophysics Data System (ADS)

    Youn, Young-Sang; Lee, Jeongmook; Kim, Jandee; Kim, Jong-Yun

    2018-06-01

    Compositional changes at the interface between thorium-doped uranium dioxide (U0.97Th0.03O2) and Zr before and after annealing at 1700 °C for 18 h were studied by X-ray photoelectron spectroscopy, X-ray diffraction, and Raman spectroscopy. At room temperature, the U0.97Th0.03O2 pellet consisted of hyperstoichiometric UO2+x with UO2 and ThO2, and the Zr sample contained Zr with ZrO2. After annealing, the former contained stoichiometric UO2 with ThO2 and the latter consisted of ZrO2 along with ZrO2·2H2O.

  17. Silkworm cocoons inspire models for random fiber and particulate composites

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Chen Fujia; Porter, David; Vollrath, Fritz

    The bioengineering design principles evolved in silkworm cocoons make them ideal natural prototypes and models for structural composites. Cocoons depend for their stiffness and strength on the connectivity of bonding between their constituent materials of silk fibers and sericin binder. Strain-activated mechanisms for loss of bonding connectivity in cocoons can be translated directly into a surprisingly simple yet universal set of physically realistic as well as predictive quantitative structure-property relations for a wide range of technologically important fiber and particulate composite materials.

  18. Silkworm cocoons inspire models for random fiber and particulate composites

    NASA Astrophysics Data System (ADS)

    Chen, Fujia; Porter, David; Vollrath, Fritz

    2010-10-01

    The bioengineering design principles evolved in silkworm cocoons make them ideal natural prototypes and models for structural composites. Cocoons depend for their stiffness and strength on the connectivity of bonding between their constituent materials of silk fibers and sericin binder. Strain-activated mechanisms for loss of bonding connectivity in cocoons can be translated directly into a surprisingly simple yet universal set of physically realistic as well as predictive quantitative structure-property relations for a wide range of technologically important fiber and particulate composite materials.

  19. Compositional instability of {beta}-phase in Ni-Mn-Ga alloys

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Chernenko, V.A.

    1999-02-05

    The ferromagnetic Heusler alloys of stoichiometric Ni{sub 2}MnGa and nonstoichiometric Ni-Mn-Ga chemical compositions though not containing a noble-metal, indeed, belong to {beta}-alloys which lattice stability is decided by the Hume-Rothery mechanism: electron concentration e/a measuring the decrease of the electron energy due to the pseudogap formation and size factor. The intriguing feature of Ni-Mn-Ga alloys similarly to Ti-Ni, Cu-Al-Be and Ni-Al alloys arises that transformation temperature, M{sub s}, is dramatically dependent on concentration reflecting an extremely high sensitivity of the lattice stability toward the content variation. The main purpose of present paper is an analysis of previous data concerning themore » compositional dependence of M{sub s} from the viewpoint of searching for empirical correlation between the electron concentration and stability of {beta}-phase in Ni-Mn-Ga system. This analysis will provide a confirmation of the feasibility of a reasonable explanation of seemingly random collection of alloys grouped with respect to their M{sub s} values as well as other features. The alloys of compositional range studied previously are added here to a few alloys including ones doped with V and Ge to ensure the decisive role of e/a ratio on M{sub s}. Original results about the temperature dependent resistance behavior are presented as well.« less

  20. Complexity of culture: the role of identity and context in bicultural individuals' body ideals.

    PubMed

    Guan, Mei; Lee, Fiona; Cole, Elizabeth R

    2012-07-01

    Culture plays an important role in shaping body image, and people from different cultures have different beliefs about what constitutes the "ideal" body type. This study examines the relationship between culture and body ideals in Asian-American and Black-American women. Results from two studies show that subjective cultural identity and situational cultural cues had different relationships with body ideals. Among Asian-American women, identification with Asian culture was related to a thinner body ideal, but exposure to Asian cultural cues (relative to American cultural cues) was related to a thicker body ideal. Among Black-American women, identification with Black culture was related to a thicker body ideal, but exposure to Black cultural cues (relative to American cultural cues) was related to a thinner body ideal. These results have theoretical and practical implications for understanding how internal and external manifestations of culture can differentially influence body image.

  1. Current and ideal skin tone: Associations with tanning behavior among sexual minority men.

    PubMed

    Klimek, Patrycja; Lamb, Kalina M; Nogg, Kelsey A; Rooney, Benjamin M; Blashill, Aaron J

    2018-06-01

    Sexual minority men have high rates of skin cancer, yet little is known about skin cancer risk behaviors in this population. It was hypothesized that current skin tone would moderate the association between darker ideals and tanning behaviors. Data were collected online from 231 sexual minority men in San Diego, United States of America, with a mean age of 24.66 (SD = 5.44). Ideal and current skin tone ratings and indoor and outdoor tanning behaviors were assessed. Darker ideals were significantly associated with increased indoor and outdoor tanning. The effect of darker ideals on tanning was strongest among individuals with lighter current skin tone, indicating a significant interaction. Sexual minority men whose perceived skin tone did not match their ideal were more likely to engage in skin cancer risk behaviors. Future skin cancer prevention programs aimed at sexual minority men may consider techniques that modify ideal skin tone internalization. Copyright © 2018 Elsevier Ltd. All rights reserved.

  2. Water: The Ideal Early Learning Environment

    ERIC Educational Resources Information Center

    Grosse, Susan J.

    2008-01-01

    Bathtubs and swimming pools provide the ideal learning environment for people with special needs. For young preschool children, the activities that take place through water can help them develop physical fitness, facilitate motor development, reinforce perceptual-motor ability, encourage social development, and enhance self-esteem and confidence.…

  3. Dissolution of multi-component LNAPL gasolines: The effects of weathering and composition

    NASA Astrophysics Data System (ADS)

    Lekmine, Greg; Bastow, Trevor P.; Johnston, Colin D.; Davis, Greg B.

    2014-05-01

    The composition of light non-aqueous phase liquid (LNAPL) gasoline and other petroleum products changes profoundly over their life once released into aquifers. However limited attention has been given to how such changes affect key parameters such as the activity coefficients which control partitioning of components of petroleum fuel into groundwater and are used to predict long-term risk from fuel releases. Laboratory experiments were conducted on a range of fresh, weathered and synthetic gasoline mixtures designed to mimic the expected changes in composition in an aquifer. Weathered gasoline created under controlled evaporation and water washing, and naturally weathered gasoline, were investigated. Equilibrium concentrations in water and molar fractions in the gasoline mixtures were compared with equilibrium concentrations predicted by Raoult's law assuming ideal behaviour of the solutions. The experiments carried out allowed the relative sensitivity of the activity coefficients of key risk drivers such as benzene, toluene, ethylbenzene and xylene (BTEX) compounds to be quantified with respect to the presence of other types of compounds and where the source LNAPL had undergone different types of weathering. Results differed for the mixtures examined but in some cases higher than predicted dissolved equilibrium concentrations showed non-ideal behaviour for toluene, benzene and xylenes. Comparison of the activity coefficients showed that the naturally weathered gasoline and a 50% evaporated unleaded gasoline present a similar range of values varying between 1.0 and 1.2, suggesting close to ideal partitioning between the LNAPL and water. The fresh and water-washed gasoline had higher values for the activity coefficient, from 1.2 to 1.4, indicating non-ideal partitioning. Results from synthetic mixtures demonstrated that these differences could be due to the different molar fractions of the nC5 and nC6 aliphatic hydrocarbons acting on the molecular interactions

  4. Tungsten fiber reinforced copper matrix composites: A review

    NASA Technical Reports Server (NTRS)

    Mcdanels, David L.

    1989-01-01

    Tungsten fiber reinforced copper matrix (W/Cu) composites have served as an ideal model system with which to analyze the properties of metal matrix composites. A series of research programs were conducted to investigate the stress-strain behavior of W/Cu composites; the effect of fiber content on the strength, modulus, and conductivity of W/Cu composites; and the effect of alloying elements on the behavior of tungsten wire and of W/Cu composites. Later programs investigated the stress-rupture, creep, and impact behavior of these composites at elevated temperatures. Analysis of the results of these programs as allows prediction of the effects of fiber properties, matrix properties, and fiber content on the properties of W/Cu composites. These analyses form the basis for the rule-of-mixtures prediction of composite properties which was universally adopted as the criteria for measuring composite efficiency. In addition, the analyses allows extrapolation of potential properties of other metal matrix composites and are used to select candidate fibers and matrices for development of tungsten fiber reinforced superalloy composite materials for high temperature aircraft and rocket engine turbine applications. The W/Cu composite efforts are summarized, some of the results obtained are described, and an update is provided on more recent work using W/Cu composites as high strength, high thermal conductivity composite materials for high heat flux, elevated temperature applications.

  5. "The part of me that you bring out": ideal similarity and the Michelangelo phenomenon.

    PubMed

    Rusbult, Caryl E; Kumashiro, Madoka; Kubacka, Kaska E; Finkel, Eli J

    2009-01-01

    This work examines the Michelangelo phenomenon, an interpersonal model of the means by which people move closer to (vs. further from) their ideal selves. The authors propose that partner similarity--similarity to the ideal self, in particular--plays an important role in this process. Across 4 studies employing diverse designs and measurement techniques, they observed consistent evidence that when partners possess key elements of one another's ideal selves, each person affirms the other by eliciting important aspects of the other's ideals, each person moves closer to his or her ideal self, and couple well-being is enhanced. Partner similarity to the actual self also accounts for unique variance in key elements of this model. The associations of ideal similarity and actual similarity with couple well-being are fully attributable to the Michelangelo process, to partner affirmation and target movement toward the ideal self. The authors also performed auxiliary analyses to rule out several alternative interpretations of these findings.

  6. Ideal light concentrators with reflector gaps

    DOEpatents

    Winston, Roland

    1980-01-01

    A cylindrical or trough-like radiant energy concentration and collection device is provided. The device includes an energy absorber, a glazing enveloping the absorber and a reflective wall. The ideal contour of the reflective wall is determined with reference to a virtual absorber and not the actual absorber cross section.

  7. Theory of phase stabilities and bonding mechanisms in stoichiometric and substoichiometric molybdenum carbide

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Hugosson, H.W.; Eriksson, O.; Nordstroem, L.

    1999-10-01

    First principles, total energy methods have been applied to predict the relative stabilities of the four experimentally verified MoC phases: the cubic {delta}(NaCl) phase and the three hexagonal {gamma}(WC), {eta} and {gamma}{sup {prime}}(TiAs) phases. The effect of vacancies on the relative stability of these four phases was investigated using a model structure with ordered vacancies within the carbon sublattice. For stoichiometric MoC, the {gamma} phase was found to be the most stable followed by {gamma}{sup {prime}}, {delta}, and {eta}, but for substoichiometric MoC{sub 0.75}, the order of relative stability was changed and the substoichiometric {delta} phase was found to havemore » the lowest energy followed by {gamma}{sup {prime}} and {gamma}. A study of the electronic structure revealed vacancy induced peaks in the density of state and the electron density attached to these peaks was analyzed and found to emanate from unscreened Mo{endash}Mo bonds through the carbon vacancy site. Finally, the oxygen stabilization of the {gamma}{sup {prime}} MoC phase was studied. {copyright} {ital 1999 American Institute of Physics.}« less

  8. Ideal MHD Stability Prediction and Required Power for EAST Advanced Scenario

    NASA Astrophysics Data System (ADS)

    Chen, Junjie; Li, Guoqiang; Qian, Jinping; Liu, Zixi

    2012-11-01

    The Experimental Advanced Superconducting Tokamak (EAST) is the first fully superconducting tokamak with a D-shaped cross-sectional plasma presently in operation. The ideal magnetohydrodynamic (MHD) stability and required power for the EAST advanced tokamak (AT) scenario with negative central shear and double transport barrier (DTB) are investigated. With the equilibrium code TOQ and stability code GATO, the ideal MHD stability is analyzed. It is shown that a moderate ratio of edge transport barriers' (ETB) height to internal transport barriers' (ITBs) height is beneficial to ideal MHD stability. The normalized beta βN limit is about 2.20 (without wall) and 3.70 (with ideal wall). With the scaling law of energy confinement time, the required heating power for EAST AT scenario is calculated. The total heating power Pt increases as the toroidal magnetic field BT or the normalized beta βN is increased.

  9. Good feelings in christianity and buddhism: religious differences in ideal affect.

    PubMed

    Tsai, Jeanne L; Miao, Felicity F; Seppala, Emma

    2007-03-01

    Affect valuation theory (AVT) predicts cultural variation in the affective states that people ideally want to feel (i.e., "ideal affect"). National and ethnic comparisons support this prediction: For instance, European Americans (EA) value high arousal positive (HAP) states (e.g., excitement) more and low arousal positive (LAP) states (e.g., calm) less than Hong Kong Chinese. In this article, the authors examine whether religions differ in the ideal affective states they endorse. The authors predicted that Christianity values HAP more and LAP less than Buddhism. In Study 1, they compared Christian and Buddhist practitioners' ideal affect. In Studies 2 and 3, they compared the endorsement of HAP and LAP in Christian and Buddhist classical texts (e.g., Gospels, Lotus Sutra) and contemporary self-help books (e.g., Your Best Life Now, Art of Happiness). Findings supported predictions, suggesting that AVT applies to religious and to national and ethnic cultures.

  10. End-Member Formulation of Solid Solutions and Reactive Transport

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Lichtner, Peter C.

    2015-09-01

    A model for incorporating solid solutions into reactive transport equations is presented based on an end-member representation. Reactive transport equations are solved directly for the composition and bulk concentration of the solid solution. Reactions of a solid solution with an aqueous solution are formulated in terms of an overall stoichiometric reaction corresponding to a time-varying composition and exchange reactions, equivalent to reaction end-members. Reaction rates are treated kinetically using a transition state rate law for the overall reaction and a pseudo-kinetic rate law for exchange reactions. The composition of the solid solution at the onset of precipitation is assumed tomore » correspond to the least soluble composition, equivalent to the composition at equilibrium. The stoichiometric saturation determines if the solid solution is super-saturated with respect to the aqueous solution. The method is implemented for a simple prototype batch reactor using Mathematica for a binary solid solution. Finally, the sensitivity of the results on the kinetic rate constant for a binary solid solution is investigated for reaction of an initially stoichiometric solid phase with an undersaturated aqueous solution.« less

  11. Non-stoichiometric O-acetylation of Shigella flexneri 2a O-specific polysaccharide: synthesis and antigenicity.

    PubMed

    Gauthier, Charles; Chassagne, Pierre; Theillet, François-Xavier; Guerreiro, Catherine; Thouron, Françoise; Nato, Farida; Delepierre, Muriel; Sansonetti, Philippe J; Phalipon, Armelle; Mulard, Laurence A

    2014-06-28

    Synthetic functional mimics of the O-antigen from Shigella flexneri 2a are seen as promising vaccine components against endemic shigellosis. Herein, the influence of the polysaccharide non-stoichiometric di-O-acetylation on antigenicity is addressed for the first time. Three decasaccharides, representing relevant internal mono- and di-O-acetylation profiles of the O-antigen, were synthesized from a pivotal protected decasaccharide designed to tailor late stage site-selective O-acetylation. The latter was obtained via a convergent route involving the imidate glycosylation chemistry. Binding studies to five protective mIgGs showed that none of the acetates adds significantly to broad antibody recognition. Yet, one of the five antibodies had a unique pattern of binding. With IC50 in the micromolar to submicromolar range mIgG F22-4 exemplifies a remarkable tight binding antibody against diversely O-acetylated and non-O-acetylated fragments of a neutral polysaccharide of medical importance.

  12. Accurately tuning the charge on giant polyoxometalate type Keplerates through stoichiometric interaction with cationic surfactants.

    PubMed

    Kistler, Melissa L; Patel, Komal G; Liu, Tianbo

    2009-07-07

    We report an approach of exploring the interaction between cationic surfactants and a type of structurally well-defined, spherical "Keplerate" polyoxometalate (POM) macroanionic molecular clusters, {Mo72V30}, in aqueous solution. The effectiveness of the interaction can be determined by monitoring the size change of the "blackberry" supramolecular structures formed by the self-assembly of {Mo72V30} macroions, which is determined by the effective charge density on the macroions. Long-chain surfactants (CTAB and CTAT) can interact with {Mo72V30} macroions stoichiometrically and lower their charge density. Consequently, the blackberry size decreases continuously with increasing surfactant concentration in solution. On the other hand, for short-chain surfactants (e.g., OTAB), a larger fraction of surfactants exist as discrete chains in solution and do not strongly interact with the macroions. This approach shows that a controllable amount of suitable surfactants can accurately tune the charge on large molecular clusters.

  13. Ideal Gas Laws: Experiments for General Chemistry

    ERIC Educational Resources Information Center

    Deal, Walter J.

    1975-01-01

    Describes a series of experiments designed to verify the various relationships implicit in the ideal gas equation and shows that the success of the Graham's law effusion experiments can be explained by elementary hydrodynamics. (GS)

  14. Complementary construction of ideal nonimaging concentrators and its applications.

    PubMed

    Gordon, J M

    1996-10-01

    A construction principle for ideal nonimaging concentrators based on the complementary edge rays outside the nominal field of view is presented, with illustrations for the trumpet, compound parabolic concentrator, and compound hyperbolic concentrator. A simple string construction for the trumpet concentrator is shown to follow from this observation-the trumpet having been the one ideal concentrator for which no string-construction method had previously been noted. An application of these observations for solar concentrator design when nonisothermal receivers are advantageous is also presented.

  15. Fracture of Carbon Nanotube - Amorphous Carbon Composites: Molecular Modeling

    NASA Technical Reports Server (NTRS)

    Jensen, Benjamin D.; Wise, Kristopher E.; Odegard, Gregory M.

    2015-01-01

    Carbon nanotubes (CNTs) are promising candidates for use as reinforcements in next generation structural composite materials because of their extremely high specific stiffness and strength. They cannot, however, be viewed as simple replacements for carbon fibers because there are key differences between these materials in areas such as handling, processing, and matrix design. It is impossible to know for certain that CNT composites will represent a significant advance over carbon fiber composites before these various factors have been optimized, which is an extremely costly and time intensive process. This work attempts to place an upper bound on CNT composite mechanical properties by performing molecular dynamics simulations on idealized model systems with a reactive forcefield that permits modeling of both elastic deformations and fracture. Amorphous carbon (AC) was chosen for the matrix material in this work because of its structural simplicity and physical compatibility with the CNT fillers. It is also much stiffer and stronger than typical engineering polymer matrices. Three different arrangements of CNTs in the simulation cell have been investigated: a single-wall nanotube (SWNT) array, a multi-wall nanotube (MWNT) array, and a SWNT bundle system. The SWNT and MWNT array systems are clearly idealizations, but the SWNT bundle system is a step closer to real systems in which individual tubes aggregate into large assemblies. The effect of chemical crosslinking on composite properties is modeled by adding bonds between the CNTs and AC. The balance between weakening the CNTs and improving fiber-matrix load transfer is explored by systematically varying the extent of crosslinking. It is, of course, impossible to capture the full range of deformation and fracture processes that occur in real materials with even the largest atomistic molecular dynamics simulations. With this limitation in mind, the simulation results reported here provide a plausible upper limit on

  16. Deposition and characterization of stoichiometric films of V2O5 on Pd(111)

    NASA Astrophysics Data System (ADS)

    Feng, Xu; Abdel-Rahman, Mohammed K.; Kruppe, Christopher M.; Trenary, Michael

    2017-10-01

    A simple and efficient method has been used to grow V2O5 thin films on Pd(111) at a substrate temperature of 300 K through physical vapor deposition by heating a fine powder of V2O5 in a non-oxidative, UHV environment. X-ray photoelectron spectroscopy (XPS), reflection absorption infrared spectroscopy (RAIRS) and low energy electron diffraction (LEED) were used to characterize the thin films. When the as-grown films exceed a minimum thickness, characteristic features of V2O5 were revealed by XPS and RAIRS, which confirms the presence of stoichiometric V2O5. LEED indicates no long range order of the as-grown films at 300 K. Annealing to temperatures between 600 and 700 K causes a reduction of V2O5 to VO2 as identified by XPS and the formation of ordered structures as determined by LEED, and VO2 is predominant after annealing to 800 K. After further annealing to 1000 K, only an ordered form of V2O3 is present on Pd(111).

  17. Butt-coupled interface between stoichiometric Si3N4 and thin-film plasmonic waveguides

    NASA Astrophysics Data System (ADS)

    Dabos, G.; Ketzaki, D.; Tsiokos, D.; Pleros, N.

    2017-02-01

    Plasmonic technology has emerged as the most promising candidate to revolutionize future photonic-integrated-circuits (PICs) and deliver performance breakthroughs in diverse application areas by providing increased light-matter interaction at the nanometer scale, overcoming the diffraction limit. However, high insertion losses of plasmonic devices impede their practical deployment in PICs. To overcome this hurdle, selective integration of individual plasmonic devices on low-loss photonic platforms is considered, allowing for enhanced chip-scale functionalities with realistic power budgets. In this context, highly-efficient and fabrication-tolerant optical interfaces for co-planar plasmonic and photonic waveguides become essential, bridging these two "worlds" and ease combined high-volume manufacturing. Herein, a TM-mode butt-coupled interface for stoichiometric Si3N4 and Au-based thin-film plasmonic waveguides is proposed aiming to be utilized for bio-sensing applications. Following a systematic design process, this new configuration has been analyzed through 3D FDTD numerical simulations demonstrating coupling efficiencies up to 64% at the wavelength of 1.55 μm, with increased fabrication tolerance compared to silicon based waveguide alternatives.

  18. Stoichiometric and Oxygen-Deficient VO2 as Versatile Hole Injection Electrode for Organic Semiconductors.

    PubMed

    Fu, Keke; Wang, Rongbin; Katase, Takayoshi; Ohta, Hiromichi; Koch, Norbert; Duhm, Steffen

    2018-03-28

    Using photoemission spectroscopy, we show that the surface electronic structure of VO 2 is determined by the temperature-dependent metal-insulator phase transition and the density of oxygen vacancies, which depends on the temperature and ultrahigh vacuum (UHV) conditions. The atomically clean and stoichiometric VO 2 surface is insulating at room temperature and features an ultrahigh work function of up to 6.7 eV. Heating in UHV just above the phase transition temperature induces the expected metallic phase, which goes in hand with the formation of oxygen defects (up to 6% in this study), but a high work function >6 eV is maintained. To demonstrate the suitability of VO 2 as hole injection contact for organic semiconductors, we investigated the energy-level alignment with the prototypical organic hole transport material N, N'-di(1-naphthyl)- N, N'-diphenyl-(1,1'-biphenyl)-4,4'-diamine (NPB). Evidence for strong Fermi-level pinning and the associated energy-level bending in NPB is found, rendering an Ohmic contact for holes.

  19. Two-octave spanning supercontinuum generation in stoichiometric silicon nitride waveguides pumped at telecom wavelengths.

    PubMed

    Porcel, Marco A G; Schepers, Florian; Epping, Jörn P; Hellwig, Tim; Hoekman, Marcel; Heideman, René G; van der Slot, Peter J M; Lee, Chris J; Schmidt, Robert; Bratschitsch, Rudolf; Fallnich, Carsten; Boller, Klaus-J

    2017-01-23

    We demonstrate supercontinuum generation in stoichiometric silicon nitride (Si3N4 in SiO2) integrated optical waveguides, pumped at telecommunication wavelengths. The pump laser is a mode-locked erbium fiber laser at a wavelength of 1.56 µm with a pulse duration of 120 fs. With a waveguide-internal pulse energy of 1.4 nJ and a waveguide with 1.0 µm × 0.9 µm cross section, designed for anomalous dispersion across the 1500 nm telecommunication range, the output spectrum extends from the visible, at around 526 nm, up to the mid-infrared, at least to 2.6 µm, the instrumental limit of our detection. This output spans more than 2.2 octaves (454 THz at the -30 dB level). The measured output spectra agree well with theoretical modeling based on the generalized nonlinear Schrödinger equation. The infrared part of the supercontinuum spectra shifts progressively towards the mid-infrared, well beyond 2.6 µm, by increasing the width of the waveguides.

  20. Critical Reflection as a Rationalistic Ideal

    ERIC Educational Resources Information Center

    van Woerkom, Marianne

    2010-01-01

    There is a growing interest in the concept of critical reflection in the adult learning and management literature. In this article, the author examines four different intellectual traditions that inform the use of the term "critical reflection" on the different ideals they express and the different definitions of critical reflection they use. On…

  1. Derivation of the Ideal Gas Law

    ERIC Educational Resources Information Center

    Laugier, Alexander; Garai, Jozsef

    2007-01-01

    Undergraduate and graduate physics and chemistry books usually state that combining the gas laws results in the ideal gas law. Leaving the derivation to the students implies that this should be a simple task, most likely a substitution. Boyle's law, Charles's law, and the Avogadro's principle are given under certain conditions; therefore, direct…

  2. Developing Ideal Student and Residency Programs.

    ERIC Educational Resources Information Center

    Selvin, Gerald J.

    1993-01-01

    The Veterans Administration (VA) is a primary educator of optometry students, with each college of optometry being affiliated with at least one VA hospital. Ideally, fourth-year optometry students rotate through a specific VA facility for about 12 weeks. Guidelines are designed to provide optimum care in a rich learning environment. (MSE)

  3. Direct Synthetic Control over the Size, Composition, and Photocatalytic Activity of Octahedral Copper Oxide Materials: Correlation Between Surface Structure and Catalytic Functionality.

    PubMed

    Nguyen, Michelle A; Bedford, Nicholas M; Ren, Yang; Zahran, Elsayed M; Goodin, Robert C; Chagani, Fatima F; Bachas, Leonidas G; Knecht, Marc R

    2015-06-24

    We report a synthetic approach to form octahedral Cu2O microcrystals with a tunable edge length and demonstrate their use as catalysts for the photodegradation of aromatic organic compounds. In this particular study, the effects of the Cu(2+) and reductant concentrations and stoichiometric ratios were carefully examined to identify their roles in controlling the final material composition and size under sustainable reaction conditions. Varying the ratio and concentrations of Cu(2+) and reductant added during the synthesis determined the final morphology and composition of the structures. Octahedral particles were prepared at selected Cu(2+):glucose ratios that demonstrated a range of photocatalytic reactivity. The results indicate that material composition, surface area, and substrate charge effects play important roles in controlling the overall reaction rate. In addition, analysis of the post-reacted materials revealed photocorrosion was inhibited and that surface etching had preferentially occurred at the particle edges during the reaction, suggesting that the reaction predominately occurred at these interfaces. Such results advance the understanding of how size and composition affect the surface interface and catalytic functionality of materials.

  4. The effect of fibre loading and graphene on the mechanical properties of goat hair fibre epoxy composite

    NASA Astrophysics Data System (ADS)

    Jayaseelan, J.; Vijayakumar, K. R.; Ethiraj, N.; Sivabalan, T.; nallayan, W. Andrew

    2017-12-01

    Composite materials are heterogenous materials containing one or more solid phases. In recent years cost-effective composite making is an ideal task. Hence we have come out with a natural fibre composite, which contains goat hair and epoxy as a binding element, with the combination of Graphene as a main source of enhanced mechanical property. Fabrication of natural composite consists of five layers of goat hair sandwiched in epoxy matrix. These composites made are tested for mechanical properties including Tensile strength, Flexural strength, Inter laminar shear and Impact strength. The mechanical properties of the six composite sets are analyzed and reported.

  5. Structural and magnetic properties of nanostructured composites (SrFe12O19)x(CaCu3Ti4O12)1-x

    NASA Astrophysics Data System (ADS)

    Gavrilova, T. P.; Deeva, J. A.; Yatsyk, I. V.; Yagfarova, A. R.; Gilmutdinov, I. F.; Lyadov, N. M.; Milovich, F. O.; Chupakhina, T. I.; Eremina, R. M.

    2018-05-01

    (SrFe12O19)x(CaCu3Ti4O12)1-x (x = 0.01, 0.03, 0.07, 0.1) composites were synthesized using a solid state method, while the pre-synthesized strontium hexaferrite SrFe12O19 (SFO) was added to the stoichiometric amount of CaO, CuO and TiO oxides to form the CaCu3Ti4O12 (CCTO) structure around SFO microinclusions. The structural and microstructural properties of obtained composites were studied by X-ray diffraction, scanning electron microscopy and transmission electron microscopy techniques. The magnetic properties were studied by electron spin resonance and magnetometry methods. Based on all experimental data we can conclude, that SFOxCCTO1-x nanostructured composites were formed only for concentrations x = 0.03 and x = 0.07, where SFO nanoinclusions are inside CCTO matrix, that leads to the strong mutual influence of the magnetic properties of both component.

  6. A continuum deformation theory for metal-matrix composites at high temperature

    NASA Technical Reports Server (NTRS)

    Robinson, D. N.

    1987-01-01

    A continuum theory is presented for representing the high temperature, time dependent, hereditary deformation behavior of metallic composites that can be idealized as pseudohomogeneous continua with locally definable directional characteristics. Homogenization of textured materials (molecular, granular, fibrous) and applicability of continuum mechanics in structural applications depends on characteristic body dimensions, the severity of gradients (stress, temperature, etc.) in the structure and the relative size of the internal structure (cell size) of the material. The point of view taken here is that the composite is a material in its own right, with its own properties that can be measured and specified for the composite as a whole.

  7. Motion planning for an adaptive wing structure with macro-fiber composite actuators

    NASA Astrophysics Data System (ADS)

    Schröck, J.; Meurer, T.; Kugi, A.

    2009-05-01

    A systematic approach for flatness-based motion planning and feedforward control is presented for the transient shaping of a piezo-actuated rectangular cantilevered plate modeling an adaptive wing. In the first step the consideration of an idealized infinite-dimensional input allows to determine the state and input parametrization in terms of a flat or basic output, which is used for a systematic motion planning approach. Subsequently, the obtained idealized input function is projected onto a finite number of suitably placed Macro-fiber Composite (MFC) patch actuators. The tracking performance of the proposed approach is evaluated in a simulation scenario.

  8. Karl Jaspers on the disease entity: Kantian ideas and Weberian ideal types.

    PubMed

    Walker, Chris

    2014-09-01

    Jaspers' nosology is indebted to Immanuel Kant's theory of knowledge. He drew the distinction of form and content from the Transcendental Analytic of Kant's Critique of Pure Reason. The distinction is universal to all knowledge, including psychopathology. Individual experience is constituted by a form or category of the Understanding to give a determinate or knowable object classified into the generic type of a real disease entity. The application of form and content is limited by the boundaries of experience. Beyond this boundary are wholes whose conception requires Ideas of reason drawn from the Transcendental Dialectic. Wholes are regulated by Ideas of reason to give an object or schema of the Idea collected into ideal types of an ideal typical disease entity. Jaspers drew ideal types from Max Weber's social theory. He anticipated that, as knowledge advanced, ideal typical disease entities would become real disease entities. By 1920, this had been the destiny of general paralysis as knowledge of its neuropathology, serology and microbiology emerged. As he presented the final edition of General Psychopathology in 1946, Jaspers was anticipating the transition of schizophrenia from ideal typical to real disease entity. Almost 70 years later, with knowledge of its aetiology still unclear, schizophrenia remains marooned as an ideal typical disease entity - still awaiting that crucial advance! © The Author(s) 2014.

  9. Composite fabrication and polymer modification using neoteric solvents

    NASA Astrophysics Data System (ADS)

    Eastman, Scott A.

    liquid/polymer solutions, PVOH was also partially esterified with low surface energy substituents. Both surface tension and surface composition of the ionic liquid/polymer solutions can be manipulated by the stoichiometric addition of low surface energy acid chlorides. This work on the modification of PVOH can be directly applied to the modification of polysaccharides such as cellulose which could have important implications from a sustainability and energy standpoint.

  10. Development of BEM for ceramic composites

    NASA Technical Reports Server (NTRS)

    Henry, D. P.; Banerjee, P. K.; Dargush, G. F.

    1991-01-01

    It is evident that for proper micromechanical analysis of ceramic composites, one needs to use a numerical method that is capable of idealizing the individual fibers or individual bundles of fibers embedded within a three-dimensional ceramic matrix. The analysis must be able to account for high stress or temperature gradients from diffusion of stress or temperature from the fiber to the ceramic matrix and allow for interaction between the fibers through the ceramic matrix. The analysis must be sophisticated enough to deal with the failure of fibers described by a series of increasingly sophisticated constitutive models. Finally, the analysis must deal with micromechanical modeling of the composite under nonlinear thermal and dynamic loading. This report details progress made towards the development of a boundary element code designed for the micromechanical studies of an advanced ceramic composite. Additional effort has been made in generalizing the implementation to allow the program to be applicable to real problems in the aerospace industry.

  11. Evaluation and modeling of the eutectic composition of various drug-polyethylene glycol solid dispersions.

    PubMed

    Baird, Jared A; Taylor, Lynne S

    2011-06-01

    The purpose of this study was to gain a better understanding of which factors contribute to the eutectic composition of drug-polyethylene glycol (PEG) blends and to compare experimental values with predictions from the semi-empirical model developed by Lacoulonche et al. Eutectic compositions of various drug-PEG 3350 solid dispersions were predicted, assuming athermal mixing, and compared to experimentally determined eutectic points. The presence or absence of specific interactions between the drug and PEG 3350 were investigated using Fourier transform infrared (FT-IR) spectroscopy. The eutectic composition for haloperidol-PEG and loratadine-PEG solid dispersions was accurately predicted using the model, while predictions for aceclofenac-PEG and chlorpropamide-PEG were very different from those experimentally observed. Deviations in the model prediction from ideal behavior for the systems evaluated were confirmed to be due to the presence of specific interactions between the drug and polymer, as demonstrated by IR spectroscopy. Detailed analysis showed that the eutectic composition prediction from the model is interdependent on the crystal lattice energy of the drug compound (evaluated from the melting temperature and the heat of fusion) as well as the nature of the drug-polymer interactions. In conclusion, for compounds with melting points less than 200°C, the model is ideally suited for predicting the eutectic composition of systems where there is an absence of drug-polymer interactions.

  12. The Formation of Wassonite: A New Titanium Monosulfide Mineral in the Yamato 691 Enstatite Chondrite

    NASA Technical Reports Server (NTRS)

    Nakamura-Messenger, K.; Keller, L. P.; Messenger, S.; Rubin, A. E.; Choi, B.-G.; Petaev, M. I.; Clemett, S. J.; Zhang, S.; Rahman, Z.; Oikawa, K.

    2011-01-01

    Wassonite, ideally stoichiometric TiS, is a titanium monosulfide not previously observed in nature, that was discovered within the Yamato 691 EH3 enstatite chondrite [1]. Because of the submicrometer size of the wassonite grains, it was not possible to determine conventional macroscopic properties. However, the chemical composition and crystal structure were well constrained by extensive quantitative energy dispersive x-ray analysis and electron diffraction using transmission electron microscopy (TEM). The crystal system for wassonite is rhombohedral (a = 3.42 plus or minus 0.07, c = 26.50 plus or minus 0.53 Angstroms) with space group: R(sup 3 raised bar) m (R9 type), cell volume: 268.4 plus or minus 0.53 Angstroms(sup 3), Z=9, density (calculated): 4.452 grams per cubic centimeter, empirical formula: (Ti(sub 0.93), Fe(sub 0.06), Cr(sub 0.01))S. In this study, we discuss possible formation mechanisms of wassonite and its associated minerals based on the petrology, mineralogy, crystallography, thermodynamic calculations, Al/Mg isotopic systematics and the O-isotopic composition of the wassonite-bearing BO chondrule.

  13. Technical Note: On the calculation of stopping-power ratio for stoichiometric calibration in proton therapy

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Ödén, Jakob; Zimmerman, Jens; Nowik, Patrik

    2015-09-15

    Purpose: The quantitative effects of assumptions made in the calculation of stopping-power ratios (SPRs) are investigated, for stoichiometric CT calibration in proton therapy. The assumptions investigated include the use of the Bethe formula without correction terms, Bragg additivity, the choice of I-value for water, and the data source for elemental I-values. Methods: The predictions of the Bethe formula for SPR (no correction terms) were validated against more sophisticated calculations using the SRIM software package for 72 human tissues. A stoichiometric calibration was then performed at our hospital. SPR was calculated for the human tissues using either the assumption of simplemore » Bragg additivity or the Seltzer-Berger rule (as used in ICRU Reports 37 and 49). In each case, the calculation was performed twice: First, by assuming the I-value of water was an experimentally based value of 78 eV (value proposed in Errata and Addenda for ICRU Report 73) and second, by recalculating the I-value theoretically. The discrepancy between predictions using ICRU elemental I-values and the commonly used tables of Janni was also investigated. Results: Errors due to neglecting the correction terms to the Bethe formula were calculated at less than 0.1% for biological tissues. Discrepancies greater than 1%, however, were estimated due to departures from simple Bragg additivity when a fixed I-value for water was imposed. When the I-value for water was calculated in a consistent manner to that for tissue, this disagreement was substantially reduced. The difference between SPR predictions when using Janni’s or ICRU tables for I-values was up to 1.6%. Experimental data used for materials of relevance to proton therapy suggest that the ICRU-derived values provide somewhat more accurate results (root-mean-square-error: 0.8% versus 1.6%). Conclusions: The conclusions from this study are that (1) the Bethe formula can be safely used for SPR calculations without correction terms

  14. The Heat Capacity of Ideal Gases

    ERIC Educational Resources Information Center

    Scott, Robert L.

    2006-01-01

    The heat capacity of an ideal gas has been shown to be calculable directly by statistical mechanics if the energies of the quantum states are known. However, unless one makes careful calculations, it is not easy for a student to understand the qualitative results. Why there are maxima (and occasionally minima) in heat capacity-temperature curves…

  15. Ideal gas behavior of a strongly coupled complex (dusty) plasma.

    PubMed

    Oxtoby, Neil P; Griffith, Elias J; Durniak, Céline; Ralph, Jason F; Samsonov, Dmitry

    2013-07-05

    In a laboratory, a two-dimensional complex (dusty) plasma consists of a low-density ionized gas containing a confined suspension of Yukawa-coupled plastic microspheres. For an initial crystal-like form, we report ideal gas behavior in this strongly coupled system during shock-wave experiments. This evidence supports the use of the ideal gas law as the equation of state for soft crystals such as those formed by dusty plasmas.

  16. Oxidation of Benzene by Persulfate in the Presence of Fe(III)- and Mn(IV)-Containing Oxides: Stoichiometric Efficiency and Transformation Products.

    PubMed

    Liu, Haizhou; Bruton, Thomas A; Li, Wei; Buren, Jean Van; Prasse, Carsten; Doyle, Fiona M; Sedlak, David L

    2016-01-19

    Sulfate radical (SO4(•-)) is a strong, short-lived oxidant that is produced when persulfate (S2O8(2-)) reacts with transition metal oxides during in situ chemical oxidation (ISCO) of contaminated groundwater. Although engineers are aware of the ability of transition metal oxides to activate persulfate, the operation of ISCO remediation systems is hampered by an inadequate understanding of the factors that control SO4(•-) production and the overall efficiency of the process. To address these shortcomings, we assessed the stoichiometric efficiency and products of transition metal-catalyzed persulfate oxidation of benzene with pure iron- and manganese-containing minerals, clays, and aquifer solids. For most metal-containing solids, the stoichiometric efficiency, as determined by the loss of benzene relative to the loss of persulfate, approached the theoretical maximum. Rates of production of SO4(•-) or hydroxyl radical (HO(•)) generated from radical chain reactions were affected by the concentration of benzene, with rates of S2O8(2-) decomposition increasing as the benzene concentration increased. Under conditions selected to minimize the loss of initial transformation products through reaction with radicals, the production of phenol only accounted for 30%-60% of the benzene lost in the presence of O2. The remaining products included a ring-cleavage product that appeared to contain an α,β-unsaturated aldehyde functional group. In the absence of O2, the concentration of the ring-cleavage product increased relative to phenol. The formation of the ring-cleavage product warrants further studies of its toxicity and persistence in the subsurface.

  17. Individual deals within teams: Investigating the role of relative i-deals for employee performance.

    PubMed

    Vidyarthi, Prajya R; Singh, Satvir; Erdogan, Berrin; Chaudhry, Anjali; Posthuma, Richard; Anand, Smriti

    2016-11-01

    The authors extend i-deals theory to an individual-within-a-team context. Drawing upon social comparison theory, they contend that individuals will react to their own i-deals within the context of group members' i-deals. Therefore, they examine the role of relative i-deals (an individual's i-deals relative to the team's average) in relation to employee performance. Furthermore, integrating social comparison theory with social identity theory the authors assert that the behavioral outcomes of relative i-deals are influenced by the team's social and structural attributes of team orientation and task interdependence. Finally, they contend that the perceptions of one's relative standing with the leader, or leader-member exchange social comparison (LMXSC), mediate the i-deals-outcome relationship in groups with low team orientation and task interdependence. Results of multilevel modeling using time-lagged data from 321 employees nested in 46 teams demonstrated that the positive relationship between relative i-deals and employee performance was stronger in groups with low team orientation and task interdependence, and the mediation effect of LMXSC was stronger in teams with low rather than high team orientation. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

  18. Qualifications of an Ideal Teacher According to Social Studies Preservice Teachers

    ERIC Educational Resources Information Center

    Gencturk, Ebru; Akbas, Yavuz; Kaymakci, Selahattin

    2012-01-01

    In this study, the question of what kind of qualifications an ideal social studies teacher has tried to be investigated. For this purpose, freshman social studies preservice teachers' perceptions about the concept of "ideal teacher" were explored. This study was designed with document analysis, one of the methods of qualitative approach.…

  19. Bayesian Ideal Types: Integration of Psychometric Data for Visually Impaired Persons.

    ERIC Educational Resources Information Center

    Jones, W. P.

    1991-01-01

    A model is proposed for the clinical synthesis of data from psychological tests of persons with visual impairments. The model integrates the concepts of the ideal type and Bayesian probability and compares actual test scores with ideal scores through use of a pattern similarity coefficient. A pilot study with Business Enterprise Program operators…

  20. An ideal observer analysis of visual working memory.

    PubMed

    Sims, Chris R; Jacobs, Robert A; Knill, David C

    2012-10-01

    Limits in visual working memory (VWM) strongly constrain human performance across many tasks. However, the nature of these limits is not well understood. In this article we develop an ideal observer analysis of human VWM by deriving the expected behavior of an optimally performing but limited-capacity memory system. This analysis is framed around rate-distortion theory, a branch of information theory that provides optimal bounds on the accuracy of information transmission subject to a fixed information capacity. The result of the ideal observer analysis is a theoretical framework that provides a task-independent and quantitative definition of visual memory capacity and yields novel predictions regarding human performance. These predictions are subsequently evaluated and confirmed in 2 empirical studies. Further, the framework is general enough to allow the specification and testing of alternative models of visual memory (e.g., how capacity is distributed across multiple items). We demonstrate that a simple model developed on the basis of the ideal observer analysis-one that allows variability in the number of stored memory representations but does not assume the presence of a fixed item limit-provides an excellent account of the empirical data and further offers a principled reinterpretation of existing models of VWM. PsycINFO Database Record (c) 2012 APA, all rights reserved.

  1. An Ideal Observer Analysis of Visual Working Memory

    PubMed Central

    Sims, Chris R.; Jacobs, Robert A.; Knill, David C.

    2013-01-01

    Limits in visual working memory (VWM) strongly constrain human performance across many tasks. However, the nature of these limits is not well understood. In this paper we develop an ideal observer analysis of human visual working memory, by deriving the expected behavior of an optimally performing, but limited-capacity memory system. This analysis is framed around rate–distortion theory, a branch of information theory that provides optimal bounds on the accuracy of information transmission subject to a fixed information capacity. The result of the ideal observer analysis is a theoretical framework that provides a task-independent and quantitative definition of visual memory capacity and yields novel predictions regarding human performance. These predictions are subsequently evaluated and confirmed in two empirical studies. Further, the framework is general enough to allow the specification and testing of alternative models of visual memory (for example, how capacity is distributed across multiple items). We demonstrate that a simple model developed on the basis of the ideal observer analysis—one which allows variability in the number of stored memory representations, but does not assume the presence of a fixed item limit—provides an excellent account of the empirical data, and further offers a principled re-interpretation of existing models of visual working memory. PMID:22946744

  2. No Surgical Innovation Without Evaluation: Evolution and Further Development of the IDEAL Framework and Recommendations.

    PubMed

    Hirst, Allison; Philippou, Yiannis; Blazeby, Jane; Campbell, Bruce; Campbell, Marion; Feinberg, Joshua; Rovers, Maroeska; Blencowe, Natalie; Pennell, Christopher; Quinn, Tom; Rogers, Wendy; Cook, Jonathan; Kolias, Angelos G; Agha, Riaz; Dahm, Philipp; Sedrakyan, Art; McCulloch, Peter

    2018-04-24

    To update, clarify, and extend IDEAL concepts and recommendations. New surgical procedures, devices, and other complex interventions need robust evaluation for safety, efficacy, and effectiveness. Unlike new medicines, there is no internationally agreed evaluation pathway for generating and analyzing data throughout the life cycle of surgical innovations. The IDEAL Framework and Recommendations were designed to provide this pathway and they have been used increasingly since their introduction in 2009. Based on a Delphi survey, expert workshop and major discussions during IDEAL conferences held in Oxford (2016) and New York (2017), this article updates and extends the IDEAL Recommendations, identifies areas for future research, and discusses the ethical problems faced by investigators at each IDEAL stage. The IDEAL Framework describes 5 stages of evolution for new surgical therapeutic interventions-Idea, Development, Exploration, Assessment, and Long-term Study. This comprehensive update proposes several modifications. First, a "Pre-IDEAL" stage describing preclinical studies has been added. Second we discuss potential adaptations to expand the scope of IDEAL (originally designed for surgical procedures) to accommodate therapeutic devices, through an IDEAL-D variant. Third, we explicitly recognise the value of comprehensive data collection through registries at all stages in the Framework and fourth, we examine the ethical issues that arise at each stage of IDEAL and underpin the recommendations. The Recommendations for each stage are reviewed, clarified and additional detail added. The intention of this article is to widen the practical use of IDEAL by clarifying the rationale for and practical details of the Recommendations. Additional research based on the experience of implementing these Recommendations is needed to further improve them.

  3. Exploring the Professional Ideals of Christian Teachers from Conservative Protestant Schools in the Netherlands

    ERIC Educational Resources Information Center

    Boele-de Bruin, H. L.; de Muynck, A.

    2018-01-01

    Professional ideals arise from personal worldviews and specify teachers' professional identities. This study aimed to explore how faith is present in the professional ideals of Christian teachers. The professional ideals of 107 Dutch teachers from conservative Protestant primary and secondary schools were explored using an open-ended…

  4. Compositions of Spherules and Rock Surfaces at Meridiani

    NASA Technical Reports Server (NTRS)

    Mittlefehldt, David W.; Jolliff, B. L.; Clark, B. C.; Gellert, R.

    2007-01-01

    The Alpha Particle X-ray Spectrometers (APXS) on the Mars Exploration Rovers (MER) have proven extremely valuable for analyzing rocks and soils on the surface of Mars. The precision of their compositional measurements has been shown to be phenomenal through analyses of the compositionally very uniform Meridiani soils. Through combined use of the rock abrasion tool (RAT) and the analytical instruments on the in-situ deployment device (IDD), analyses of the interiors of fine-grained and texturally uniform rocks with surfaces ground flat have been made under conditions that are nearly ideal for this mode of analysis. The APXS has also been used frequently to analyze materials whose characteristics, surface morphologies, and sample-detector geometries are less than ideal, but the analyses of which are nonetheless very useful for understanding the makeup of the target materials. Such targets include undisturbed rocks with irregular and sometimes coated surfaces and mixed targets such as soils that include fine-grained components as well as coarse grains and pieces of rocks. Such target materials include the well known hematite-rich concretions, referred to as blueberries because of their multispectral color, size, and mode of occurrence. In addition to non-ideal target geometry, such mixed materials also present a heterogeneous target in terms of density. These irregularities violate the assumptions commonly associated with analyses done in the laboratory to achieve the highest possible accuracy. Here we acknowledge the irregularities and we examine the inferences drawn from specific chemical trends obtained on imperfect targets in light of one of the potential pitfalls of natural materials on the surface of Mars, namely thin dust coatings.

  5. Prediction of high temperature metal matrix composite ply properties

    NASA Technical Reports Server (NTRS)

    Caruso, J. J.; Chamis, C. C.

    1988-01-01

    The application of the finite element method (superelement technique) in conjunction with basic concepts from mechanics of materials theory is demonstrated to predict the thermomechanical behavior of high temperature metal matrix composites (HTMMC). The simulated behavior is used as a basis to establish characteristic properties of a unidirectional composite idealized an as equivalent homogeneous material. The ply properties predicted include: thermal properties (thermal conductivities and thermal expansion coefficients) and mechanical properties (moduli and Poisson's ratio). These properties are compared with those predicted by a simplified, analytical composite micromechanics model. The predictive capabilities of the finite element method and the simplified model are illustrated through the simulation of the thermomechanical behavior of a P100-graphite/copper unidirectional composite at room temperature and near matrix melting temperature. The advantage of the finite element analysis approach is its ability to more precisely represent the composite local geometry and hence capture the subtle effects that are dependent on this. The closed form micromechanics model does a good job at representing the average behavior of the constituents to predict composite behavior.

  6. The Role of Idealization in Science and Its Implications for Science Education

    NASA Astrophysics Data System (ADS)

    Niaz, Mansoor

    1999-06-01

    The main objective of this article is to study the role of empirical evidence in the interpretation of psychological and epistemological aspects of Piagetian theory. According to Galilean methodology, after having asked the right question, a scientist could experimentally vary one impediment, and observe what happens to the dependent variable, as it approaches the ideal limiting case. Following Galileo's idealization, scientific laws being epistemological constructions do not describe the behavior of actual bodies. It is plausible to suggest that just as Galileo's ideal law can be observed only when all the impediment variables approach zero, similarly individuals in the real world have various `impediments' and it is only when these impediments are gradually removed by experimental manipulation that the real performance of individuals can approximate the competence of Piaget's epistemic subject (ideal knower). Finally, evidence is presented to the effect that by experimentally manipulating the impediment variables (e.g., Pascual-Leone's M-demand and Witkin's perceptual field effect of a task), performance of the real subjects approximates the competence of the ideal epistemic subject, which leads to the construction of a neo-Piagetian epistemological theory.

  7. An ideal sealed source life-cycle

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Tompkins, Joseph Andrew

    2009-01-01

    system they we have today. This regulation created a new regulatory framework seen as promising at the time. However, now they recognize that, despite the good intentions, the NIJWP/85 has not solved any source disposition problems. The answer to these sealed source disposition problems is to adopt a philosophy to correct these regulatory issues, determine an interim solution, execute that solution until there is a minimal backlog of sources to deal with, and then let the mechanisms they have created solve this problem into the foreseeable future. The primary philosophical tenet of the ideal sealed source life cycle follows. You do not allow the creation (or importation) of any source whose use cannot be justified, which cannot be affordably shipped, or that does not have a well-delinated and affordable disposition pathway. The path forward dictates that we fix the problem by embracing the Ideal Source Life cycle. In figure 1, we can see some of the elements of the ideal source life cycle. The life cycle is broken down into four portions, manufacture, use, consolidation, and disposition. These four arbitrary elements allow them to focus on the ideal life cycle phases that every source should go through between manufacture and final disposition. As we examine the various phases of the sealed source life cycle, they pick specific examples and explore the adoption of the ideal life cycle model.« less

  8. American Citizens’ Views of an Ideal Pig Farm

    PubMed Central

    Sato, Patrycia; Hötzel, Maria J.; von Keyserlingk, Marina A.G.

    2017-01-01

    Simple Summary The public, who also make up the largest proportion of consumers of animal products, often criticize farm animal industries in regards to their care and handling of farm animals. The U.S. swine industry has not been exempt from such criticisms. The aim of this study was to explore the views of the people not affiliated with the swine industry on what they perceived to be the ideal pig/pork farm, and their associated reasons. Through an online survey, participants were invited to respond to the following open-ended question: “What do you consider to be an ideal pig/pork farm and why are these characteristics important to you?”. Respondents considered animal care, profitability, farm size, compliance with sanitary, environmental rules and regulations, farm cleanliness and sanitary standards, and workers’ rights and welfare important, but also raised concerns relating to pigs’ quality of life including space to move, feeding, contact with outdoors or nature, absence of pain, suffering and mistreatment. Perspectives were also raised regarding the ideal farm as a profitable business operation, clean, and with optimal sanitary conditions. Respondents also emphasized naturalness, frequently stating that pigs should have access to the outdoors, and rejected the use of hormones, antibiotics, and other chemicals for the purposes of increasing production. Abstract Food animal production practices are often cited as having negative animal welfare consequences. The U.S. swine industry has not been exempt from such criticisms. Little is known, however, about how lay citizens who are not actively engaged in agricultural discussions, think about swine production. Thus, the aim of this study was to explore the views of people not affiliated with the swine industry on what they perceived to be the ideal pig/pork farm, and their associated reasons. Through an online survey, participants were invited to respond to the following open-ended question: “What do

  9. Differential molar heat capacities to test ideal solubility estimations.

    PubMed

    Neau, S H; Bhandarkar, S V; Hellmuth, E W

    1997-05-01

    Calculation of the ideal solubility of a crystalline solute in a liquid solvent requires knowledge of the difference in the molar heat capacity at constant pressure of the solid and the supercooled liquid forms of the solute, delta Cp. Since this parameter is not usually known, two assumptions have been used to simplify the expression. The first is that delta Cp can be considered equal to zero; the alternate assumption is that the molar entropy of fusion, delta Sf, is an estimate of delta Cp. Reports claiming the superiority of one assumption over the other, on the basis of calculations done using experimentally determined parameters, have appeared in the literature. The validity of the assumptions in predicting the ideal solubility of five structurally unrelated compounds of pharmaceutical interest, with melting points in the range 420 to 470 K, was evaluated in this study. Solid and liquid heat capacities of each compound near its melting point were determined using differential scanning calorimetry. Linear equations describing the heat capacities were extrapolated to the melting point to generate the differential molar heat capacity. Linear data were obtained for both crystal and liquid heat capacities of sample and test compounds. For each sample, ideal solubility at 298 K was calculated and compared to the two estimates generated using literature equations based on the differential molar heat capacity assumptions. For the compounds studied, delta Cp was not negligible and was closer to delta Sf than to zero. However, neither of the two assumptions was valid for accurately estimating the ideal solubility as given by the full equation.

  10. Theory and Simulation of Real and Ideal Magnetohydrodynamic Turbulence

    NASA Technical Reports Server (NTRS)

    Shebalin, John V.

    2004-01-01

    Incompressible, homogeneous magnetohydrodynamic (MHD) turbulence consists of fluctuating vorticity and magnetic fields, which are represented in terms of their Fourier coefficients. Here, a set of five Fourier spectral transform method numerical simulations of two-dimensional (2-D) MHD turbulence on a 512(sup 2) grid is described. Each simulation is a numerically realized dynamical system consisting of Fourier modes associated with wave vectors k, with integer components, such that k = |k| less than or equal to k(sub max). The simulation set consists of one ideal (non-dissipative) case and four real (dissipative) cases. All five runs had equivalent initial conditions. The dimensions of the dynamical systems associated with these cases are the numbers of independent real and imaginary parts of the Fourier modes. The ideal simulation has a dimension of 366104, while each real simulation has a dimension of 411712. The real runs vary in magnetic Prandtl number P(sub M), with P(sub M) is a member of {0.1, 0.25, 1, 4}. In the results presented here, all runs have been taken to a simulation time of t = 25. Although ideal and real Fourier spectra are quite different at high k, they are similar at low values of k. Their low k behavior indicates the existence of broken symmetry and coherent structure in real MHD turbulence, similar to what exists in ideal MHD turbulence. The value of PM strongly affects the ratio of kinetic to magnetic energy and energy dissipation (which is mostly ohmic). The relevance of these results to 3-D Navier-Stokes and MHD turbulence is discussed.

  11. A Multidimensional Ideal Point Item Response Theory Model for Binary Data

    ERIC Educational Resources Information Center

    Maydeu-Olivares, Albert; Hernandez, Adolfo; McDonald, Roderick P.

    2006-01-01

    We introduce a multidimensional item response theory (IRT) model for binary data based on a proximity response mechanism. Under the model, a respondent at the mode of the item response function (IRF) endorses the item with probability one. The mode of the IRF is the ideal point, or in the multidimensional case, an ideal hyperplane. The model…

  12. 40 CFR 1065.645 - Amount of water in an ideal gas.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Amount of water in an ideal gas. 1065.645 Section 1065.645 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Calculations and Data Requirements § 1065.645 Amount of water in an ideal gas. This section describes how to...

  13. 40 CFR 1065.645 - Amount of water in an ideal gas.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 34 2013-07-01 2013-07-01 false Amount of water in an ideal gas. 1065.645 Section 1065.645 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Calculations and Data Requirements § 1065.645 Amount of water in an ideal gas. This section describes how to...

  14. 40 CFR 1065.645 - Amount of water in an ideal gas.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 33 2011-07-01 2011-07-01 false Amount of water in an ideal gas. 1065.645 Section 1065.645 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Calculations and Data Requirements § 1065.645 Amount of water in an ideal gas. This section describes how to...

  15. Toward an Ideal Senior High School Governance Structure.

    ERIC Educational Resources Information Center

    Treslan, D. L.

    1979-01-01

    This paper delineates six attributes of an ideal high school governance structure: respect, freedom, rationality, flexibility, equality, and involvement of staff and students in the decision-making process. (Author/SJL)

  16. Ideal for Whom? A Cultural Analysis of Ideal Worker Norms in Higher Education and Student Affairs Graduate Programs

    ERIC Educational Resources Information Center

    Sallee, Margaret W.

    2016-01-01

    This chapter explores the consequences of ideal worker norms for graduate student-parents in higher education and student affairs programs. Using Schein's (2004) levels of culture as a conceptual lens, this chapter considers the ways that programmatic structures and interactions with faculty and peers reflect and reproduce a culture across…

  17. Ideal walking dynamics via a gauged NJL model

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Rantaharju, Jarno; Pica, Claudio; Sannino, Francesco

    According to the ideal walking technicolor paradigm, large mass anomalous dimensions arise in gauged Nambu–Jona-Lasinio (NJL) models when the four-fermion coupling is sufficiently strong to induce spontaneous symmetry breaking in an otherwise conformal gauge theory. Therefore, we study the SU(2) gauged NJL model with two adjoint fermions using lattice simulations. The model is in an infrared conformal phase at small NJL coupling while it displays a chirally broken phase at large NJL couplings. In the infrared conformal phase, we find that the mass anomalous dimension varies with the NJL coupling, reaching γm ~ 1 close to the chiral symmetry breakingmore » transition, de facto making the present model the first explicit realization of the ideal walking scenario.« less

  18. Ideal walking dynamics via a gauged NJL model

    DOE PAGES

    Rantaharju, Jarno; Pica, Claudio; Sannino, Francesco

    2017-07-25

    According to the ideal walking technicolor paradigm, large mass anomalous dimensions arise in gauged Nambu–Jona-Lasinio (NJL) models when the four-fermion coupling is sufficiently strong to induce spontaneous symmetry breaking in an otherwise conformal gauge theory. Therefore, we study the SU(2) gauged NJL model with two adjoint fermions using lattice simulations. The model is in an infrared conformal phase at small NJL coupling while it displays a chirally broken phase at large NJL couplings. In the infrared conformal phase, we find that the mass anomalous dimension varies with the NJL coupling, reaching γm ~ 1 close to the chiral symmetry breakingmore » transition, de facto making the present model the first explicit realization of the ideal walking scenario.« less

  19. Hyperpolarized (129) Xe imaging of the rat lung using spiral IDEAL.

    PubMed

    Doganay, Ozkan; Wade, Trevor; Hegarty, Elaine; McKenzie, Charles; Schulte, Rolf F; Santyr, Giles E

    2016-08-01

    To implement and optimize a single-shot spiral encoding strategy for rapid 2D IDEAL projection imaging of hyperpolarized (Hp) (129) Xe in the gas phase, and in the pulmonary tissue (PT) and red blood cells (RBCs) compartments of the rat lung, respectively. A theoretical and experimental point spread function analysis was used to optimize the spiral k-space read-out time in a phantom. Hp (129) Xe IDEAL images from five healthy rats were used to: (i) optimize flip angles by a Bloch equation analysis using measured kinetics of gas exchange and (ii) investigate the feasibility of the approach to characterize the exchange of Hp (129) Xe. A read-out time equal to approximately 1.8 × T2* was found to provide the best trade-off between spatial resolution and signal-to-noise ratio (SNR). Spiral IDEAL approaches that use the entire dissolved phase magnetization should give an SNR improvement of a factor of approximately three compared with Cartesian approaches with similar spatial resolution. The IDEAL strategy allowed imaging of gas, PT, and RBC compartments with sufficient SNR and temporal resolution to permit regional gas exchange measurements in healthy rats. Single-shot spiral IDEAL imaging of gas, PT and RBC compartments and gas exchange is feasible in rat lung using Hp (129) Xe. Magn Reson Med 76:566-576, 2016. © 2015 Wiley Periodicals, Inc. © 2015 Wiley Periodicals, Inc.

  20. Ideal gender identity related to parent images and locus of control: Jungian and social learning perspectives.

    PubMed

    Shimoda, Hiroko; Keskinen, Soili

    2004-06-01

    In this research, we wanted to clarify how gender images are different or invariant and related to parents, attributes, and the attitude of controlling life (locus of control) in two cultural contexts, Japan and Finland. For this purpose, students' ideal gender images, consisting of ideal mother, female, father and male images, and parents' similarity to the four ideal gender images were studied in 135 Japanese and 119 Finnish university students. Major findings were (a) Japanese students' ideal gender images were more stereotypic than those of Finnish students; (b) students' ideal mother image and parents' similarity to the ideal mother image were related only to their sex, which supports Jung's theory; (c) students socially learned other ideal gender images, but these did not fit with expectation from social learning theory; (d) Japanese students' mothers are models or examples of gender images, but Finnish male students did not seem to base their ideal gender images on their parents. Implication of measures was discussed.

  1. Na2.5Fe1.75(SO4)3/Ketjen/rGO: An advanced cathode composite for sodium ion batteries

    NASA Astrophysics Data System (ADS)

    Goñi, A.; Iturrondobeitia, A.; Gil de Muro, I.; Lezama, L.; Rojo, T.

    2017-11-01

    An advanced cathode composite Na2.5Fe1.75(SO4)3/Ketjen/rGO for sodium ion batteries has been prepared, joining together the excellent electrochemical properties of the three components: off stoichiometric iron sulfate alluaudite, Ketjen Black carbon and reduced graphene oxide (rGO). This electrode material has been exhaustively characterized by XRD, thermogravimetric analysis, Raman spectroscopy and SEM and TEM microscopy. The study has demonstrated that a high quality electrode material has been designed containing a porous sulfate core properly coated by interweaved rGO fibers and Ketjen Black nanoparticles. The electrochemical study has revealed an excellent performance providing specific capacities close to the theoretical one at 1C. Additionally, this composite has shown a very good rate capability and a great cycling stability for at least 200 cycles maintaining a coulombic efficiency of 96%. The post mortem analysis, which includes EPR and XPS measurements, has demonstrated that the carbonaceous coating on the composite generates a stable and protective SEI layer over the active material guaranteeing a successful performance during a long cycle life.

  2. Do the Particles of an Ideal Gas Collide?

    ERIC Educational Resources Information Center

    Lesk, Arthur M.

    1974-01-01

    Describes the collisional properties as a logically essential component of the ideal gas model since an actual intraparticle process cannot support observable anisotropic velocity distributions without collisions taken into account. (CC)

  3. Solid Oxide Membrane (SOM) Process for Facile Electrosynthesis of Metal Carbides and Composites

    NASA Astrophysics Data System (ADS)

    Zou, Xingli; Chen, Chaoyi; Lu, Xionggang; Li, Shangshu; Xu, Qian; Zhou, Zhongfu; Ding, Weizhong

    2017-02-01

    Metal carbides (MCs) and composites including TiC, SiC, TaC, ZrC, NbC, Ti5Si3/TiC, and Nb/Nb5Si3 have been directly electrosynthesized from their stoichiometric metal oxides/carbon (MOs/C) mixture precursors by an innovative solid oxide membrane (SOM)-assisted electrochemical process. MOs/C mixture powders including TiO2/C, SiO2/C, Ta2O5/C, ZrO2/C, Nb2O5/C, TiO2/SiO2/C, Nb2O5/SiO2 were pressed to form porous pellets and then served as cathode precursors. A SOM-based anode, made from yttria-stabilized zirconia (YSZ)-based membrane, was used to control the electroreduction process. The SOM electrochemical process was performed at 1273 K (1000 °C) and 3.5 to 4.0 V in molten CaCl2. The oxygen component contained in the MOs/C precursors was gradually removed during electroreduction process, and thus, MOs/C can be directly converted into MCs and composites at the cathode. The reaction mechanism of the electroreduction process and the characteristics of the obtained MCs and composites products were systematically investigated. The results show that the electrosynthesis process typically involves compounding, electroreduction, dissolution-electrodeposition, and in situ carbonization processes. The products can be predesigned and controlled to form micro/nanostructured MCs and composites. Multicomponent multilayer composites (MMCs) have also been tried to electrosynthesize in this work. It is suggested that the SOM-assisted electroreduction process has great potential to be used for the facile and green synthesis of various MCs and composites.

  4. Ideal cardiovascular health and psychosocial risk factors among Finnish female municipal workers.

    PubMed

    Veromaa, Veera; Kautiainen, Hannu; Saxen, Ulla; Malmberg-Ceder, Kirsi; Bergman, Elina; Korhonen, Päivi E

    2017-02-01

    Ideal cardiovascular health has been defined by the American Heart Association as the absence of disease and the presence of seven key health factors and behaviours. However, little is known about the mental aspects associated with ideal cardiovascular health metrics. The objective of this study was to assess the relationships between psychosocial risk factors and ideal cardiovascular health metrics among Finnish women at municipal work units. A cross-sectional study was conducted in Finland among 732 female employees (mean±SD age 48±10 years) from ten work units in 2014. Ideal cardiovascular health metrics were evaluated with a physical examination, laboratory tests, medical history and self-administrated questionnaires. Psychosocial risk factors (social isolation, stress, depressive symptoms, anxiety, hostility and type D personality) were assessed with core questions as suggested by the European Society of Cardiology. The prevalence of having 5-7 ideal cardiovascular health metrics was 183 (25.0%), of whom 54.1% had at least one psychosocial risk factor. Anxiety (31.3%), work stress (30.7%) and type D personality (26.1%) were the most prevalent of the psychosocial risk factors. The prevalence of depressive symptoms ( p<0.001) and type D personality ( p=0.049) decreased linearly according to the sum of ideal cardiovascular health metrics after adjustment for age and years of education. Even women with good cardiovascular health are affected by psychosocial risk factors at municipal work units. Although the association is possibly bidirectional, screening and treating depression and dealing with type D personality might be crucial in improving cardiovascular health among women.

  5. The predictive validity of ideal partner preferences: a review and meta-analysis.

    PubMed

    Eastwick, Paul W; Luchies, Laura B; Finkel, Eli J; Hunt, Lucy L

    2014-05-01

    A central element of interdependence theory is that people have standards against which they compare their current outcomes, and one ubiquitous standard in the mating domain is the preference for particular attributes in a partner (ideal partner preferences). This article reviews research on the predictive validity of ideal partner preferences and presents a new integrative model that highlights when and why ideals succeed or fail to predict relational outcomes. Section 1 examines predictive validity by reviewing research on sex differences in the preference for physical attractiveness and earning prospects. Men and women reliably differ in the extent to which these qualities affect their romantic evaluations of hypothetical targets. Yet a new meta-analysis spanning the attraction and relationships literatures (k = 97) revealed that physical attractiveness predicted romantic evaluations with a moderate-to-strong effect size (r = ∼.40) for both sexes, and earning prospects predicted romantic evaluations with a small effect size (r = ∼.10) for both sexes. Sex differences in the correlations were small (r difference = .03) and uniformly nonsignificant. Section 2 reviews research on individual differences in ideal partner preferences, drawing from several theoretical traditions to explain why ideals predict relational evaluations at different relationship stages. Furthermore, this literature also identifies alternative measures of ideal partner preferences that have stronger predictive validity in certain theoretically sensible contexts. Finally, a discussion highlights a new framework for conceptualizing the appeal of traits, the difference between live and hypothetical interactions, and the productive interplay between mating research and broader psychological theories.

  6. Patients respond more positively to physicians who focus on their ideal affect.

    PubMed

    Sims, Tamara; Tsai, Jeanne L

    2015-06-01

    Previous findings suggest that patients choose physicians whose affective focus matches how they ideally want to feel (Sims et al., 2014). For instance, the more people wanted to feel excitement, the more likely they were to hypothetically choose a new physician who promoted excitement. What remains unknown is whether this match shapes how patients actually respond to physicians after being assigned to them (i.e., whether they adhere to physicians' recommendations more and evaluate physicians more positively). To this end, community adults reported their global ideal affect and actual affect (how they ideally want to feel and actually feel during a typical week, respectively), and were randomly assigned to receive health recommendations from either a physician who expressed and promoted high arousal positive states (HAP) (e.g., excitement), or one who expressed and promoted low arousal positive states (LAP) (e.g., calm). For the next 5 days, participants reported their daily adherence to the recommendations and their daily ideal and actual affect. At the end of the week, participants evaluated their physician. As predicted, the more participants wanted to feel HAP, the more they adhered to the "HAP-focused" physician's recommendations, and the more participants wanted to feel LAP, the more they adhered to the "LAP-focused" physician's recommendations. Participants also evaluated their physician more positively when his affective focus matched their ideal affect. Neither global nor daily actual affect systematically predicted how patients responded to their physicians. These findings suggest that patients respond better to physicians whose affective focus matches their ideal affect. (c) 2015 APA, all rights reserved).

  7. Patients Respond More Positively to Physicians Who Focus on Their Ideal Affect

    PubMed Central

    Sims, Tamara; Tsai, Jeanne L.

    2014-01-01

    Previous findings suggest that patients choose physicians whose affective focus matches how they ideally want to feel (Sims et al., 2014). For instance, the more people wanted to feel excitement, the more likely they were to hypothetically choose a new physician who promoted excitement. What remains unknown is whether this match shapes how patients actually respond to physicians after being assigned to them (i.e., whether they adhere to physicians’ recommendations more and evaluate physicians more positively). To this end, community adults reported their global ideal affect and actual affect (how they ideally want to feel and actually feel during a typical week, respectively), and were randomly assigned to receive health recommendations from either a physician who expressed and promoted high arousal positive states (HAP) (e.g., excitement), or one who expressed and promoted low arousal positive states (LAP) (e.g., calm). For the next five days, participants reported their daily adherence to the recommendations and their daily ideal and actual affect. At the end of the week, participants evaluated their physician. As predicted, the more participants wanted to feel HAP, the more they adhered to the “HAP-focused” physician’s recommendations, and the more participants wanted to feel LAP, the more they adhered to the “LAP-focused” physician’s recommendations. Participants also evaluated their physician more positively when his affective focus matched their ideal affect. Neither global nor daily actual affect systematically predicted how patients responded to their physicians. These findings suggest that patients respond better to physicians whose affective focus matches their ideal affect. PMID:25313670

  8. Associations between Sexual Abstinence Ideals, Religiosity, and Alcohol Abstinence: A Longitudinal Study of Finnish Twins

    PubMed Central

    Winter, Torsten; Karvonen, Sakari; Rose, Richard J.

    2016-01-01

    We analyzed prevalence and stability of attitudes endorsing sexual abstinence ideals from late adolescence into early adulthood and studied associations of these attitudes with religiosity and alcohol abstinence in a sexually liberal Nordic society. Our population-based sample of Finnish twins permitted comparisons of co-twins concordant for religiosity but discordant for drinking to evaluate the association of sexual abstinence ideals with alcohol abstinence, controlling for household environment. From age 17 to 24, endorsement of sexual abstinence as a romantic ideal declined from 25% to 15%. Religiosity and alcohol abstinence correlated, both separately and together, with endorsing sexual abstinence. Abstinence ideals were associated with literal belief in fundamental tenets of the Bible. The association of sexual abstinence ideals with alcohol abstinence was confirmed in within-family comparisons of co-twins discordant for drinking but concordant for religiosity. Alcohol-abstinent twins were significantly more likely than their non-alcohol-abstinent twin siblings to endorse sexual abstinence ideals; that result suggests the association of sexual abstinence ideals with abstaining from alcohol is not explained by unmeasured confounds in familial background and structure. Our longitudinal results and analyses of discordant twins suggest that attitudes toward sexual abstinence ideals are embedded within other conservative attitudes and behaviors. PMID:23301620

  9. Compositional disorder and its effect on the thermoelectric performance of Zn₃P₂ nanowire-copper nanoparticle composites.

    PubMed

    Brockway, Lance; Vasiraju, Venkata; Vaddiraju, Sreeram

    2014-03-28

    Recent studies indicated that nanowire format of materials is ideal for enhancing the thermoelectric performance of materials. Most of these studies were performed using individual nanowires as the test elements. It is not currently clear whether bulk assemblies of nanowires replicate this enhanced thermoelectric performance of individual nanowires. Therefore, it is imperative to understand whether enhanced thermoelectric performance exhibited by individual nanowires can be extended to bulk assemblies of nanowires. It is also imperative to know whether the addition of metal nanoparticle to semiconductor nanowires can be employed for enhancing their thermoelectric performance further. Specifically, it is important to understand the effect of microstructure and composition on the thermoelectric performance on bulk compound semiconductor nanowire-metal nanoparticle composites. In this study, bulk composites composed of mixtures of copper nanoparticles with either unfunctionalized or 1,4-benzenedithiol (BDT) functionalized Zn₃P₂ nanowires were fabricated and analyzed for their thermoelectric performance. The results indicated that use of BDT functionalized nanowires for the fabrication of composites leads to interface-engineered composites that have uniform composition all across their cross-section. The interface engineering allows for increasing their Seebeck coefficients and electrical conductivities, relative to the Zn₃P₂ nanowire pellets. In contrast, the use of unfunctionalized Zn₃P₂ nanowires for the fabrication of composite leads to the formation of composites that are non-uniform in composition across their cross-section. Ultimately, the composites were found to have Zn₃P₂ nanowires interspersed with metal alloy nanoparticles. Such non-uniform composites exhibited very high electrical conductivities, but slightly lower Seebeck coefficients, relative to Zn₃P₂ nanowire pellets. These composites were found to show a very high zT of 0.23 at 770

  10. The influence of family context on life, educational and occupational ideal among middle school students in China.

    PubMed

    Yao, Benxian; Zhang, Ling; Zhen, Rui; Zhou, Xiao

    2016-06-01

    This study examined the relationship between family context of middle school students on their educational and occupational ideals. Middle school students (N = 2000) responded to questions assessing family location, family structure, parental educational level and family economic status, as well as to the Middle School Students' Ideals Questionnaire. Multivariate analysis of variance indicated that life, educational and occupational ideals of female students and students in lower grades were higher than that of male students and students in higher grades. Regression analysis indicated that paternal education level have a positive association with educational and occupational ideals, but not life ideals, and family economic status have a positive relation to life ideals, but not educational and occupational ideals. Moreover, the interaction between family economic status and family location has a negative association with students' life, educational and occupational ideals. These results suggest that different factors predicted different ideals of adolescents, and that family economic status had a negative moderating effect on the relationship between family location and ideals of students. © 2015 International Union of Psychological Science.

  11. Ideal gas thermodynamic properties for the phenyl, phenoxy, and o-biphenyl radicals

    NASA Technical Reports Server (NTRS)

    Burcat, A.; Zeleznik, F. J.; Mcbride, B. J.

    1985-01-01

    Ideal gas thermodynamic properties of the phenyl and o-biphenyl radicals, their deuterated analogs and the phenoxy radical were calculated to 5000 K using estimated vibrational frequencies and structures. The ideal gas thermodynamic properties of benzene, biphenyl, their deuterated analogs and phenyl were also calculated.

  12. Raman spectroscopic studies of defect structures and phase transition in hyper-stoichiometric UO(2+x).

    PubMed

    He, Heming; Shoesmith, David

    2010-07-28

    A method to determine the defect structures in hyper-stoichiometric UO(2+x) using a combination of XRD and Raman spectroscopy has been developed. A sequence of phase transitions, from cubic to tetragonal symmetry, occurs with increasing degree of non-stoichiometry. This sequence proceeds from a cubic phase through an intermediate t''-type tetragonal (axial ratio c/a = 1) phase to a final t-type tetragonal (c/a not = 1) phase. Four distinct structural defect regions can be identified in the stoichiometry range, UO(2) to U(3)O(7): (i) a random point defect structure (x (in UO(2+x)) < or = 0.05); (ii) a non-stoichiometry region (0.05 < or = x < or = 0.15) over which point defects are gradually eliminated and replaced by the Willis 2:2:2 cluster; (iii) a mixture of Willis and cuboctahedral clusters (0.15 < or = x < or = 0.23); (iv) the cuboctahedral cluster (x > or = 0.23). The geometry and steric arrangement of these defects is primarily determined by the concentration of the excess-oxygen interstitials.

  13. Lifestyle constraints, not inadequate nutrition education, cause gap between breakfast ideals and realities among Japanese in Tokyo.

    PubMed

    Melby, Melissa K; Takeda, Wakako

    2014-01-01

    Japanese public health nutrition often promotes 'traditional' cuisine. In-depth interviews with 107 Japanese adults were conducted in Tokyo from 2009 to 2011, using free-listing methods to examine dietary ideals and realities to assess the extent to which realities reflect inadequate nutrition education or lifestyle constraints. Ideal-reality gaps were widest for breakfast. Most people reported Japanese ideals: rice and miso soup were prototypical foods. However, breakfast realities were predominantly western (bread-based). While those aged 40-59 were more likely to hold Japanese ideals (P=0.063), they were less likely to achieve them (P=0.007). All those reporting western ideals achieved them on weekdays, while only 64% of those with Japanese ideals achieved them (P<0.001). Partial correlations controlling for age and gender showed achievement of Japanese ideals were positively correlated with proportion of cooking-related housework, and negatively correlated with living standard and income. Ideal menu content was in line with current Japanese nutrition advice, suggesting that more nutrition education may not change dietary ideals or behavior. Participant-reported reasons for ideal-reality discordance demonstrate that work-life balance issues, especially lack of time and family structure/life rhythm, are the largest obstacles to the attainment of dietary ideals. People reporting 'no time' as a primary reason for ideal-reality gaps were less likely to achieve their Japanese ideals (odds ratio=0.212). Time realities of people's lives may undermine educational efforts promoting Japanese breakfasts. When dietary reality/behavior departs from guidelines, it is often assumed that people lack knowledge. If ideals are in line with dietary guidelines, then lack of knowledge is not the likely cause and nutrition education is not the optimal solution. By asking people about the reasons for gaps between their ideals and realities, we can identify barriers and design more

  14. The effect of exfoliated graphite on carbon fiber reinforced composites for cryogenic applications

    NASA Astrophysics Data System (ADS)

    McLaughlin, Adam Michael

    It is desirable to lighten cryogenic fuel tanks through the use of composites for the development of a reusable single stage launch vehicle. Conventional composites fall victim to microcracking due to the cyclic loading and temperature change experienced during launch and re-entry conditions. Also, the strength of a composite is generally limited by the properties of the matrix. The introduction of the nanoplatelet, exfoliated graphite or graphene, to the matrix shows promise of increasing both the microcracking resistivity and the mechanical characteristics. Several carbon fiber composite plates were manufactured with varying concentrations of graphene and tested under both room and cryogenic conditions to characterize graphene's effect on the composite. Results from tensile and fracture testing indicate that the ideal concentration of graphene in our carbon fiber reinforced polymer composites for cryogenic applications is 0.08% mass graphene.

  15. How Is the Ideal Gas Law Explanatory?

    ERIC Educational Resources Information Center

    Woody, Andrea I.

    2013-01-01

    Using the ideal gas law as a comparative example, this essay reviews contemporary research in philosophy of science concerning scientific explanation. It outlines the inferential, causal, unification, and erotetic conceptions of explanation and discusses an alternative project, the functional perspective. In each case, the aim is to highlight…

  16. Ideal versus School Learning: Analyzing Israeli Secondary School Students' Conceptions of Learning

    ERIC Educational Resources Information Center

    Hadar, Linor

    2009-01-01

    This study explored 130 secondary school students' conceptions of learning using an open-ended task, analyzed both qualitatively and quantitatively. Students' reality of learning comprised two separate spheres, ideal learning and school learning, which rarely interacted. Generally, students commented more about school than ideal learning. Factor…

  17. Development of sputtering process to deposit stoichiometric zirconia coatings for the inside wall of regeneratively cooled rocket thrust chambers

    NASA Technical Reports Server (NTRS)

    Busch, R.

    1978-01-01

    Thermal barrier coatings of yttria stabilized zirconia and zirconia-ceria mixtures were deposited by RF reactive sputtering. Coatings were 1-2 mils thick, and were deposited on copper cylinders intended to simulate the inner wall of a regeneratively cooled thrust chamber. Coating stoichiometry and adherence were investigated as functions of deposition parameters. Modest deposition rates (approximately 0.15 mil/hr) and subambient sustrate temperatures (-80 C) resulted in nearly stoichiometric coatings which remained adherent through thermal cycles between -196 and 400 C. Coatings deposited at higher rates or substrates temperatures exhibited greater oxygen deficiences, while coatings deposited at lower temperatures were not adherent. Substrate bias resulted in structural changes in the coating and high krypton contents; no clear effect on stoichiometry was observed.

  18. A complete equation of state for non-ideal condensed phase explosives

    NASA Astrophysics Data System (ADS)

    Wilkinson, S. D.; Braithwaite, M.; Nikiforakis, N.; Michael, L.

    2017-12-01

    The objective of this work is to improve the robustness and accuracy of numerical simulations of both ideal and non-ideal explosives by introducing temperature dependence in mechanical equations of state for reactants and products. To this end, we modify existing mechanical equations of state to appropriately approximate the temperature in the reaction zone. Mechanical equations of state of the Mie-Grüneisen form are developed with extensions, which allow the temperature to be evaluated appropriately and the temperature equilibrium condition to be applied robustly. Furthermore, the snow plow model is used to capture the effect of porosity on the reactant equation of state. We apply the methodology to predict the velocity of compliantly confined detonation waves. Once reaction rates are calibrated for unconfined detonation velocities, simulations of confined rate sticks and slabs are performed, and the experimental detonation velocities are matched without further parameter alteration, demonstrating the predictive capability of our simulations. We apply the same methodology to both ideal (PBX9502, a high explosive with principal ingredient TATB) and non-ideal (EM120D, an ANE or ammonium nitrate based emulsion) explosives.

  19. Learning what feelings to desire: socialization of ideal affect through children's storybooks.

    PubMed

    Tsai, Jeanne L; Louie, Jennifer Y; Chen, Eva E; Uchida, Yukiko

    2007-01-01

    Previous findings suggest that cultural factors influence ideal affect (i.e., the affective states that people ideally want to feel). Three studies tested the hypothesis that cultural differences in ideal affect emerge early in life and are acquired through exposure to storybooks. In Study 1, the authors established that consistent with previous findings, European American preschoolers preferred excited (vs. calm) states more (indexed by activity and smile preferences) and perceived excited (vs. calm) states as happier than Taiwanese Chinese preschoolers. In Study 2, it was observed that similar differences were reflected in the pictures (activities, expressions, and smiles) of best-selling storybooks in the United States and Taiwan. Study 3 found that across cultures, exposure to exciting (vs. calm) storybooks altered children's preferences for excited (vs. calm) activities and their perceptions of happiness. These findings suggest that cultural differences in ideal affect may be due partly to differential exposure to calm and exciting storybooks.

  20. Molecular determinants of cadherin ideal bond formation: Conformation-dependent unbinding on a multidimensional landscape

    PubMed Central

    Manibog, Kristine; Sankar, Kannan; Kim, Sun-Ae; Zhang, Yunxiang; Jernigan, Robert L.; Sivasankar, Sanjeevi

    2016-01-01

    Classical cadherin cell–cell adhesion proteins are essential for the formation and maintenance of tissue structures; their primary function is to physically couple neighboring cells and withstand mechanical force. Cadherins from opposing cells bind in two distinct trans conformations: strand-swap dimers and X-dimers. As cadherins convert between these conformations, they form ideal bonds (i.e., adhesive interactions that are insensitive to force). However, the biophysical mechanism for ideal bond formation is unknown. Here, we integrate single-molecule force measurements with coarse-grained and atomistic simulations to resolve the mechanistic basis for cadherin ideal bond formation. Using simulations, we predict the energy landscape for cadherin adhesion, the transition pathways for interconversion between X-dimers and strand-swap dimers, and the cadherin structures that form ideal bonds. Based on these predictions, we engineer cadherin mutants that promote or inhibit ideal bond formation and measure their force-dependent kinetics using single-molecule force-clamp measurements with an atomic force microscope. Our data establish that cadherins adopt an intermediate conformation as they shuttle between X-dimers and strand-swap dimers; pulling on this conformation induces a torsional motion perpendicular to the pulling direction that unbinds the proteins and forms force-independent ideal bonds. Torsional motion is blocked when cadherins associate laterally in a cis orientation, suggesting that ideal bonds may play a role in mechanically regulating cadherin clustering on cell surfaces. PMID:27621473

  1. Dimensional analysis using toric ideals: primitive invariants.

    PubMed

    Atherton, Mark A; Bates, Ronald A; Wynn, Henry P

    2014-01-01

    Classical dimensional analysis in its original form starts by expressing the units for derived quantities, such as force, in terms of power products of basic units [Formula: see text] etc. This suggests the use of toric ideal theory from algebraic geometry. Within this the Graver basis provides a unique primitive basis in a well-defined sense, which typically has more terms than the standard Buckingham approach. Some textbook examples are revisited and the full set of primitive invariants found. First, a worked example based on convection is introduced to recall the Buckingham method, but using computer algebra to obtain an integer [Formula: see text] matrix from the initial integer [Formula: see text] matrix holding the exponents for the derived quantities. The [Formula: see text] matrix defines the dimensionless variables. But, rather than this integer linear algebra approach it is shown how, by staying with the power product representation, the full set of invariants (dimensionless groups) is obtained directly from the toric ideal defined by [Formula: see text]. One candidate for the set of invariants is a simple basis of the toric ideal. This, although larger than the rank of [Formula: see text], is typically not unique. However, the alternative Graver basis is unique and defines a maximal set of invariants, which are primitive in a simple sense. In addition to the running example four examples are taken from: a windmill, convection, electrodynamics and the hydrogen atom. The method reveals some named invariants. A selection of computer algebra packages is used to show the considerable ease with which both a simple basis and a Graver basis can be found.

  2. Ideal Directed-Energy System To Defeat Small Unmanned Aircraft System Swarms

    DTIC Science & Technology

    2017-05-21

    AIR COMMAND AND STAFF COLLEGE AIR UNIVERSITY IDEAL DIRECTED- ENERGY SYSTEM TO DEFEAT SMALL UNMANNED AIRCRAFT SYSTEM SWARMS by David F. Pina...directed energy (DE) developmental systems indicate this class of weapons is the best solution. A review of several continuous wave laser, pulsed high...powered microwave, and electronic warfare/jamming systems indicate the following attributes as ideal for a future directed energy weapon (DEW) system

  3. Catalytic Exhaust Gas Recirculation-Loop Reforming for High Efficiency in a Stoichiometric Spark-Ignited Engine through Thermochemical Recuperation and Dilution Limit Extension, Part 2: Engine Performance

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Chang, Yan; Szybist, James P.; Pihl, Josh A.

    This is the second part of a two-part investigation of on-board catalytic fuel reforming to increase the brake efficiency of a multicylinder, stoichiometric spark-ignited (SI) engine. In Part 1 of the investigation, we analytically and experimentally characterized the energetics and kinetics of a candidate reforming catalyst over a range of reforming equivalence ratios and oxygen concentration conditions to identify the best conditions for efficient reforming. In the present part of our investigation, we studied an engine strategy that combined exhaust gas recirculation (EGR)–loop reforming with dilution limit extension of the combustion. In our experiments, we found that, under an enginemore » operating condition of 2000 rpm and brake mean effective pressure (4 bar), catalytic EGR reforming made it possible to sustain stable combustion with a volumetric equivalent of 45%–55% EGR. Under this same operating condition with stoichiometric engine exhaust (and no reforming), we were only able to sustain stable combustion with EGR under 25%. In conclusion, these results indicate that multicylinder gasoline engine efficiency can be increased substantially with catalytic reforming combined with and higher EGR operation, resulting in a decrease of more than 8% in fuel consumption, compared to baseline operation.« less

  4. Catalytic Exhaust Gas Recirculation-Loop Reforming for High Efficiency in a Stoichiometric Spark-Ignited Engine through Thermochemical Recuperation and Dilution Limit Extension, Part 2: Engine Performance

    DOE PAGES

    Chang, Yan; Szybist, James P.; Pihl, Josh A.; ...

    2018-01-17

    This is the second part of a two-part investigation of on-board catalytic fuel reforming to increase the brake efficiency of a multicylinder, stoichiometric spark-ignited (SI) engine. In Part 1 of the investigation, we analytically and experimentally characterized the energetics and kinetics of a candidate reforming catalyst over a range of reforming equivalence ratios and oxygen concentration conditions to identify the best conditions for efficient reforming. In the present part of our investigation, we studied an engine strategy that combined exhaust gas recirculation (EGR)–loop reforming with dilution limit extension of the combustion. In our experiments, we found that, under an enginemore » operating condition of 2000 rpm and brake mean effective pressure (4 bar), catalytic EGR reforming made it possible to sustain stable combustion with a volumetric equivalent of 45%–55% EGR. Under this same operating condition with stoichiometric engine exhaust (and no reforming), we were only able to sustain stable combustion with EGR under 25%. In conclusion, these results indicate that multicylinder gasoline engine efficiency can be increased substantially with catalytic reforming combined with and higher EGR operation, resulting in a decrease of more than 8% in fuel consumption, compared to baseline operation.« less

  5. Sequential Ideal-Observer Analysis of Visual Discriminations.

    ERIC Educational Resources Information Center

    Geisler, Wilson S.

    1989-01-01

    A new analysis, based on the concept of the ideal observer in signal detection theory, is described. It allows: tracing of the flow of discrimination information through the initial physiological stages of visual processing for arbitrary spatio-chromatic stimuli, and measurement of the information content of said visual stimuli. (TJH)

  6. Real vs. Ideal Self Discrepancy in Bulimics.

    ERIC Educational Resources Information Center

    Kosak, Karen

    Bulimia is an eating disorder prevalent among young women, characterized by binge eating episodes followed by purging with subsequent depressive moods and self-deprecating thoughts. To determine whether bulimic women exhibit a greater discrepancy between their perceived and ideal selves than do nonbulimics, three samples of women were assessed.…

  7. Perturbative thermodynamic geometry of nonextensive ideal classical, Bose, and Fermi gases.

    PubMed

    Mohammadzadeh, Hosein; Adli, Fereshteh; Nouri, Sahereh

    2016-12-01

    We investigate perturbative thermodynamic geometry of nonextensive ideal classical, Bose, and Fermi gases. We show that the intrinsic statistical interaction of nonextensive Bose (Fermi) gas is attractive (repulsive) similar to the extensive case but the value of thermodynamic curvature is changed by a nonextensive parameter. In contrary to the extensive ideal classical gas, the nonextensive one may be divided to two different regimes. According to the deviation parameter of the system to the nonextensive case, one can find a special value of fugacity, z^{*}, where the sign of thermodynamic curvature is changed. Therefore, we argue that the nonextensive parameter induces an attractive (repulsive) statistical interaction for zz^{*}) for an ideal classical gas. Also, according to the singular point of thermodynamic curvature, we consider the condensation of nonextensive Boson gas.

  8. Preserving idealism in global health promotion.

    PubMed

    Franco-Paredes, Carlos; Zeuli, Julia; Hernández-Ramos, Isabel; Santos-Preciado, Jose I

    2010-12-01

    If the field of global health is to evolve in the second decade of the new millennium, we need to revive the idealistic spirit and by using the lens of health equity work toward improved health status around the world. Morality and empathy are considered by-products of our evolutionary history as a human species. Idealism may be a trait that we may choose to preserve in our modern evolutionary history.

  9. Note on the ideal frame formulation

    NASA Astrophysics Data System (ADS)

    Lara, Martin

    2017-09-01

    An implementation of the ideal frame formulation of perturbed Keplerian motion is presented which only requires the integration of a differential system of dimension 7, contrary to the 8 variables traditionally integrated with this approach. The new formulation is based on the integration of a scaled version of the Eulerian set of redundant parameters and slightly improves runtime performance with respect to the 8-dimensional case while retaining comparable accuracy.

  10. Magnetic properties of nearly stoichiometric CeAuBi2 heavy fermion compound

    NASA Astrophysics Data System (ADS)

    Adriano, C.; Rosa, P. F. S.; Jesus, C. B. R.; Grant, T.; Fisk, Z.; Garcia, D. J.; Pagliuso, P. G.

    2015-05-01

    Motivated by the interesting magnetic anisotropy found in the heavy fermion family CeTX2 (T = transition metal and X = pnictogen), here, we study the novel parent compound CeAu1-xBi2-y by combining magnetization, pressure dependent electrical resistivity, and heat-capacity measurements. The magnetic properties of our nearly stoichiometric single crystal sample of CeAu1-xBi2-y (x = 0.92 and y = 1.6) revealed an antiferromagnetic ordering at TN = 12 K with an easy axis along the c-direction. The field dependent magnetization data at low temperatures reveal the existence of a spin-flop transition when the field is applied along the c-axis (Hc ˜ 7.5 T and T = 5 K). The heat capacity and pressure dependent resistivity data suggest that CeAu0.92Bi1.6 exhibits a weak heavy fermion behavior with strongly localized Ce3+ 4f electrons. Furthermore, the systematic analysis using a mean field model including anisotropic nearest-neighbors interactions and the tetragonal crystalline electric field (CEF) Hamiltonian allows us to extract a CEF scheme and two different values for the anisotropic J RKKY exchange parameters between the Ce3+ ions in this compound. Thus, we discuss a scenario, considering both the anisotropic magnetic interactions and the tetragonal CEF effects, in the CeAu1-xBi2-y compounds, and we compare our results with the isostructural compound CeCuBi2.

  11. Effect of pairwise additivity on finite-temperature behavior of classical ideal gas

    NASA Astrophysics Data System (ADS)

    Shekaari, Ashkan; Jafari, Mahmoud

    2018-05-01

    Finite-temperature molecular dynamics simulations have been applied to inquire into the effect of pairwise additivity on the behavior of classical ideal gas within the temperature range of T = 250-4000 K via applying a variety of pair potentials and then examining the temperature dependence of a number of thermodynamical properties. Examining the compressibility factor reveals the most deviation from ideal-gas behavior for the Lennard-Jones system mainly due to the presence of both the attractive and repulsive terms. The systems with either attractive or repulsive intermolecular potentials are found to present no resemblance to real gases, but the most similarity to the ideal one as temperature rises.

  12. Ideal plasma response to vacuum magnetic fields with resonant magnetic perturbations in non-axisymmetric tokamaks

    DOE PAGES

    Kim, Kimin; Ahn, J. -W.; Scotti, F.; ...

    2015-09-03

    Ideal plasma shielding and amplification of resonant magnetic perturbations in non-axisymmetric tokamak is presented by field line tracing simulation with full ideal plasma response, compared to measurements of divertor lobe structures. Magnetic field line tracing simulations in NSTX with toroidal non-axisymmetry indicate the ideal plasma response can significantly shield/amplify and phase shift the vacuum resonant magnetic perturbations. Ideal plasma shielding for n = 3 mode is found to prevent magnetic islands from opening as consistently shown in the field line connection length profile and magnetic footprints on the divertor target. It is also found that the ideal plasma shielding modifiesmore » the degree of stochasticity but does not change the overall helical lobe structures of the vacuum field for n = 3. Furthermore, amplification of vacuum fields by the ideal plasma response is predicted for low toroidal mode n = 1, better reproducing measurements of strong striation of the field lines on the divertor plate in NSTX.« less

  13. Resin Composites Reinforced by Nanoscaled Fibers or Tubes for Dental Regeneration

    PubMed Central

    Li, Xiaoming; Liu, Wei; Sun, Lianwen; Aifantis, Katerina E.; Yu, Bo; Fan, Yubo; Cui, Fuzhai; Watari, Fumio

    2014-01-01

    It has been stated clearly that nanofillers could make an enhancement on the mechanical performances of dental composites. In order to address current shortage of traditional dental composites, fillers in forms of nanofibers or nanotubes are broadly regarded as ideal candidates to greatly increase mechanical performances of dental composites with low content of fillers. In this review, the efforts using nanofibers and nanotubes to reinforce mechanical performances of dental composites, including polymeric nanofibers, metallic nanofibers or nanotubes, and inorganic nanofibers or nanotubes, as well as their researches related, are demonstrated in sequence. The first purpose of current paper was to confirm the enhancement of nanofibers or nanotubes' reinforcement on the mechanical performances of dental restorative composite. The second purpose was to make a general description about the reinforcement mechanism of nanofibers and nanotubes, especially, the impact of formation of interphase boundary interaction and nanofibers themselves on the advanced mechanical behaviors of the dental composites. By means of the formation of interface interaction and poststretching nanofibers, reinforced effect of dental composites by sorts of nanofibers/nanotubes has been successfully obtained. PMID:24982894

  14. Chitin and carbon nanotube composites as biocompatible scaffolds for neuron growth

    NASA Astrophysics Data System (ADS)

    Singh, Nandita; Chen, Jinhu; Koziol, Krzysztof K.; Hallam, Keith R.; Janas, Dawid; Patil, Avinash J.; Strachan, Ally; G. Hanley, Jonathan; Rahatekar, Sameer S.

    2016-04-01

    The design of biocompatible implants for neuron repair/regeneration ideally requires high cell adhesion as well as good electrical conductivity. Here, we have shown that plasma-treated chitin carbon nanotube composite scaffolds show very good neuron adhesion as well as support of synaptic function of neurons. The addition of carbon nanotubes to a chitin biopolymer improved the electrical conductivity and the assisted oxygen plasma treatment introduced more oxygen species onto the chitin nanotube scaffold surface. Neuron viability experiments showed excellent neuron attachment onto plasma-treated chitin nanotube composite scaffolds. The support of synaptic function was evident on chitin/nanotube composites, as confirmed by PSD-95 staining. The biocompatible and electrically-conducting chitin nanotube composite scaffold prepared in this study can be used for in vitro tissue engineering of neurons and, potentially, as an implantable electrode for stimulation and repair of neurons.

  15. Chitin and carbon nanotube composites as biocompatible scaffolds for neuron growth.

    PubMed

    Singh, Nandita; Chen, Jinhu; Koziol, Krzysztof K; Hallam, Keith R; Janas, Dawid; Patil, Avinash J; Strachan, Ally; G Hanley, Jonathan; Rahatekar, Sameer S

    2016-04-21

    The design of biocompatible implants for neuron repair/regeneration ideally requires high cell adhesion as well as good electrical conductivity. Here, we have shown that plasma-treated chitin carbon nanotube composite scaffolds show very good neuron adhesion as well as support of synaptic function of neurons. The addition of carbon nanotubes to a chitin biopolymer improved the electrical conductivity and the assisted oxygen plasma treatment introduced more oxygen species onto the chitin nanotube scaffold surface. Neuron viability experiments showed excellent neuron attachment onto plasma-treated chitin nanotube composite scaffolds. The support of synaptic function was evident on chitin/nanotube composites, as confirmed by PSD-95 staining. The biocompatible and electrically-conducting chitin nanotube composite scaffold prepared in this study can be used for in vitro tissue engineering of neurons and, potentially, as an implantable electrode for stimulation and repair of neurons.

  16. Rheological properties of poly(vinyl alcohol) (PVA) derived composite membranes for fuel cells

    NASA Astrophysics Data System (ADS)

    Remiš, T.

    2017-01-01

    Rheological properties of new anhydrous proton conducting membrane based on PVA, tetraethyl orthosilicate (TEOS),sulfosuccinic acid (SSA), titanium dioxide (TiO2)was examined at various stoichiometric ratios. SSA was used as sulfonating agents to form a crosslinked structure and as proton source, whereas TEO Sand TiO2were utilized to improve the thermal and mechanical properties of the membrane. In order to verify that all the substances were immobilized into the matrix, the membranes were analysed by means of FT-IR. The rheological, mechanical and thermal properties of the membranes were investigated using rheometer ARES G2 and thermogravimetic analyser (TGA).The analysis of mixed PVA solutions exhibited a unique behaviour of viscosity with increased crosslink density. The dynamic storage modulus G´ of dried composite membranes shows better mechanical resistance and increased tolerance to pressure applied during membrane electrode assembly (MEA).

  17. The Decisions of Elementary School Principals: A Test of Ideal Type Methodology.

    ERIC Educational Resources Information Center

    Greer, John T.

    Interviews with 25 Georgia elementary school principals provided data that could be used to test an application of Max Weber's ideal type methodology to decision-making. Alfred Schuetz's model of the rational act, based on one of Weber's ideal types, was analyzed and translated into describable acts and behaviors. Interview procedures were…

  18. Turkish Primary Science Teachers' Perceptions of an Ideal Teacher Education System

    ERIC Educational Resources Information Center

    Korkmaz, Hunkar; Altindag, Ahmet

    2017-01-01

    The goals of this descriptive study were to determine Turkish pre-service science teachers' perceptions of an ideal teacher education system. The sample consisted of 137 pre-service teachers, including 74 females and 63 males. The questionnaire was based on open-ended questions and was developed to investigate ideal teacher education system…

  19. Keeping the Bar Low: Why Russia's Nonresident Fathers Accept Narrow Fatherhood Ideals

    ERIC Educational Resources Information Center

    Utrata, Jennifer

    2008-01-01

    Although most Russian nonresident fathers feel torn between old and new ideals of fatherhood, they end up accepting older, narrow ideals. Fathers reproduce the dominant gender discourse, which deems men irresponsible and infantile and diminishes the importance of fathers. On the basis of extensive fieldwork, including in-depth interviews (N = 21)…

  20. Synthesis and Characterization of a Polyimide-Epoxy Composite for Dental Applications

    NASA Astrophysics Data System (ADS)

    Yang, An; Xu, Chun

    2018-03-01

    Epoxy (EP) resins have been employed in dentistry for years, but their intrinsic brittleness demands a reinforcement to make them an ideal dental material that combines strength, toughness, and aesthetics. In this study, an EP resin was reinforced with a low-molecular-weight polyimide (PI). The PI/EP composites were subjected to three-point bending tests and examined by the scanning electron microscopy. It was found that blending PI with EP in proper proportions strengthened EP without sacrificing its toughness. The PI/EP composite could be employed in dentistry as the matrix of fiber-reinforced dental root canal posts.