Sample records for identification repository epir

  1. High-Efficiency Polycrystalline CdS/CdTe Solar Cells on Buffered Commercial TCO-Coated Glass

    NASA Astrophysics Data System (ADS)

    Colegrove, E.; Banai, R.; Blissett, C.; Buurma, C.; Ellsworth, J.; Morley, M.; Barnes, S.; Gilmore, C.; Bergeson, J. D.; Dhere, R.; Scott, M.; Gessert, T.; Sivananthan, Siva

    2012-10-01

    Multiple polycrystalline CdS/CdTe solar cells with efficiencies greater than 15% were produced on buffered, commercially available Pilkington TEC Glass at EPIR Technologies, Inc. (EPIR, Bolingbrook, IL) and verified by the National Renewable Energy Laboratory (NREL). n-CdS and p-CdTe were grown by chemical bath deposition (CBD) and close space sublimation, respectively. Samples with sputter-deposited CdS were also investigated. Initial results indicate that this is a viable dry-process alternative to CBD for production-scale processing. Published results for polycrystalline CdS/CdTe solar cells with high efficiencies are typically based on cells using research-grade transparent conducting oxides (TCOs) requiring high-temperature processing inconducive to low-cost manufacturing. EPIR's results for cells on commercial glass were obtained by implementing a high-resistivity SnO2 buffer layer and by optimizing the CdS window layer thickness. The high-resistivity buffer layer prevents the formation of CdTe-TCO junctions, thereby maintaining a high open-circuit voltage and fill factor, whereas using a thin CdS layer reduces absorption losses and improves the short-circuit current density. EPIR's best device demonstrated an NREL-verified efficiency of 15.3%. The mean efficiency of hundreds of cells produced with a buffer layer between December 2010 and June 2011 is 14.4%. Quantum efficiency results are presented to demonstrate EPIR's progress toward NREL's best-published results.

  2. Development of novel nonvolatile memory devices using the colossal magnetoresistive oxide praseodymium-calcium-manganese trioxide

    NASA Astrophysics Data System (ADS)

    Papagianni, Christina

    Pr0.7Ca0.3MnO3 (PCMO) manganese oxide belongs in the family of materials known as transition metal oxides. These compounds have received increased attention due to their perplexing properties such as Colossal Magnetoresistance effect, Charge-Ordered phase, existence of phase-separated states etc. In addition, it was recently discovered that short electrical pulses in amplitude and duration are sufficient to induce reversible and non-volatile resistance changes in manganese perovskite oxide thin films at room temperature, known as the EPIR effect. The existence of the EPIR effect in PCMO thin films at room temperature opens a viable way for the realization of fast, high-density, low power non-volatile memory devices in the near future. The purpose of this study is to investigate, optimize and understand the properties of Pr0.7Ca0.3MnO 3 (PCMO) thin film devices and to identify how these properties affect the EPIR effect. PCMO thin films were deposited on various substrates, such as metals, and conducting and insulating oxides, by pulsed laser and radio frequency sputtering methods. Our objective was to understand and compare the induced resistive states. We attempted to identify the induced resistance changes by considering two resistive models to be equivalent to our devices. Impedance spectroscopy was also utilized in a wide temperature range that was extended down to 70K. Fitted results of the temperature dependence of the resistance states were also included in this study. In the same temperature range, we probed the resistance changes in PCMO thin films and we examined whether the phase transitions affect the EPIR effect. In addition, we included a comparison of devices with electrodes consisting of different size and different materials. We demonstrated a direct relation between the EPIR effect and the phase diagram of bulk PCMO samples. A model that could account for the observed EPIR effect is presented.

  3. Personal Name Identification in the Practice of Digital Repositories

    ERIC Educational Resources Information Center

    Xia, Jingfeng

    2006-01-01

    Purpose: To propose improvements to the identification of authors' names in digital repositories. Design/methodology/approach: Analysis of current name authorities in digital resources, particularly in digital repositories, and analysis of some features of existing repository applications. Findings: This paper finds that the variations of authors'…

  4. A New Concept for Non-Volatile Memory: The Electric-Pulse Induced Resistive Change Effect in Colossal Magnetoresistive Thin Films

    NASA Technical Reports Server (NTRS)

    Liu, S. Q.; Wu, N. J.; Ignatiev, A.

    2001-01-01

    A novel electric pulse-induced resistive change (EPIR) effect has been found in thin film colossal magnetoresistive (CMR) materials, and has shown promise for the development of resistive, nonvolatile memory. The EPIR effect is induced by the application of low voltage (< 4 V) and short duration (< 20 ns) electrical pulses across a thin film sample of a CMR material at room temperature and under no applied magnetic field. The pulse can directly either increase or decrease the resistance of the thin film sample depending on pulse polarity. The sample resistance change has been shown to be over two orders of magnitude, and is nonvolatile after pulsing. The sample resistance can also be changed through multiple levels - as many as 50 have been shown. Such a device can provide a way for the development of a new kind of nonvolatile multiple-valued memory with high density, fast write/read speed, low power-consumption, and potential high radiation-hardness.

  5. Ultra Low Noise Infrared Detector Amplifier for Next Generation Standoff Detector

    DTIC Science & Technology

    2016-02-18

    some mismatches. The formation of a heterojunction for the channel entails creating a sufficient degree of difference between the bandgap of the...metal oxide (MOS) capacitor, thereby isolating the ground from dc. EPIR Technologies, Inc. Proprietary Information – Exempt From FOIA 67 Figure

  6. 10 CFR 960.3-2 - Siting process.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REPOSITORY Implementation Guidelines § 960.3-2 Siting process. The siting process begins with site screening... first repository before the enactment of the Act, and the identification of such sites was made after... identification of potentially acceptable sites for the second and subsequent repositories shall be conducted in...

  7. MBE HgCdTe for HDVIP Devices: Horizontal Integration in the US HgCdTe FPA Industry

    NASA Astrophysics Data System (ADS)

    Aqariden, F.; Elsworth, J.; Zhao, J.; Grein, C. H.; Sivananthan, S.

    2012-10-01

    Molecular beam epitaxy (MBE) growth of HgCdTe offers the possibility of fabricating multilayer device structures with an almost unlimited choice of infrared sensor designs for focal-plane array (FPA) fabrication. HgCdTe offers two major advantages that explain its dominance in the infrared photon detector marketplace. The thermal generation rate per unit volume of the material is lower and the quantum efficiency for photon absorption in the infrared is higher in HgCdTe than in any competing material—it yields devices with quantum efficiencies as high as 0.99. Recently, EPIR Technologies and DRS Infrared Technologies agreed to collaborate and examine: (i) the feasibility of employing MBE HgCdTe in the fabrication of high-density vertically interconnected photodiodes (HDVIPs), which are usually fabricated with liquid-phase epitaxy material, and (ii) the potential benefits of horizontal integration, with EPIR supplying the MBE materials to DRS for device and array fabrication. The team designed and developed passivation-absorber-passivation structures that are heavily used by DRS. This paper provides an overview of the characteristics of HDVIP devices and arrays fabricated from MBE HgCdTe and the anticipated advantages of horizontal integration in the industry. Material growth, device fabrication, and test results are presented.

  8. Implementing the EuroFIR Document and Data Repositories as accessible resources of food composition information.

    PubMed

    Unwin, Ian; Jansen-van der Vliet, Martine; Westenbrink, Susanne; Presser, Karl; Infanger, Esther; Porubska, Janka; Roe, Mark; Finglas, Paul

    2016-02-15

    The EuroFIR Document and Data Repositories are being developed as accessible collections of source documents, including grey literature, and the food composition data reported in them. These Repositories will contain source information available to food composition database compilers when selecting their nutritional data. The Document Repository was implemented as searchable bibliographic records in the Europe PubMed Central database, which links to the documents online. The Data Repository will contain original data from source documents in the Document Repository. Testing confirmed the FoodCASE food database management system as a suitable tool for the input, documentation and quality assessment of Data Repository information. Data management requirements for the input and documentation of reported analytical results were established, including record identification and method documentation specifications. Document access and data preparation using the Repositories will provide information resources for compilers, eliminating duplicated work and supporting unambiguous referencing of data contributing to their compiled data. Copyright © 2014 Elsevier Ltd. All rights reserved.

  9. P19-S Managing Proteomics Data from Data Generation and Data Warehousing to Central Data Repository and Journal Reviewing Processes

    PubMed Central

    Thiele, H.; Glandorf, J.; Koerting, G.; Reidegeld, K.; Blüggel, M.; Meyer, H.; Stephan, C.

    2007-01-01

    In today’s proteomics research, various techniques and instrumentation bioinformatics tools are necessary to manage the large amount of heterogeneous data with an automatic quality control to produce reliable and comparable results. Therefore a data-processing pipeline is mandatory for data validation and comparison in a data-warehousing system. The proteome bioinformatics platform ProteinScape has been proven to cover these needs. The reprocessing of HUPO BPP participants’ MS data was done within ProteinScape. The reprocessed information was transferred into the global data repository PRIDE. ProteinScape as a data-warehousing system covers two main aspects: archiving relevant data of the proteomics workflow and information extraction functionality (protein identification, quantification and generation of biological knowledge). As a strategy for automatic data validation, different protein search engines are integrated. Result analysis is performed using a decoy database search strategy, which allows the measurement of the false-positive identification rate. Peptide identifications across different workflows, different MS techniques, and different search engines are merged to obtain a quality-controlled protein list. The proteomics identifications database (PRIDE), as a public data repository, is an archiving system where data are finally stored and no longer changed by further processing steps. Data submission to PRIDE is open to proteomics laboratories generating protein and peptide identifications. An export tool has been developed for transferring all relevant HUPO BPP data from ProteinScape into PRIDE using the PRIDE.xml format. The EU-funded ProDac project will coordinate the development of software tools covering international standards for the representation of proteomics data. The implementation of data submission pipelines and systematic data collection in public standards–compliant repositories will cover all aspects, from the generation of MS data in each laboratory to the conversion of all the annotating information and identifications to a standardized format. Such datasets can be used in the course of publishing in scientific journals.

  10. Classifying Clinical Trial Eligibility Criteria to Facilitate Phased Cohort Identification Using Clinical Data Repositories.

    PubMed

    Wang, Amy Y; Lancaster, William J; Wyatt, Matthew C; Rasmussen, Luke V; Fort, Daniel G; Cimino, James J

    2017-01-01

    A major challenge in using electronic health record repositories for research is the difficulty matching subject eligibility criteria to query capabilities of the repositories. We propose categories for study criteria corresponding to the effort needed for querying those criteria: "easy" (supporting automated queries), mixed (initial automated querying with manual review), "hard" (fully manual record review), and "impossible" or "point of enrollment" (not typically in health repositories). We obtained a sample of 292 criteria from 20 studies from ClinicalTrials.gov. Six independent reviewers, three each from two academic research institutions, rated criteria according to our four types. We observed high interrater reliability both within and between institutions. The analysis demonstrated typical features of criteria that map with varying levels of difficulty to repositories. We propose using these features to improve enrollment workflow through more standardized study criteria, self-service repository queries, and analyst-mediated retrievals.

  11. Classifying Clinical Trial Eligibility Criteria to Facilitate Phased Cohort Identification Using Clinical Data Repositories

    PubMed Central

    Wang, Amy Y.; Lancaster, William J.; Wyatt, Matthew C.; Rasmussen, Luke V.; Fort, Daniel G.; Cimino, James J.

    2017-01-01

    A major challenge in using electronic health record repositories for research is the difficulty matching subject eligibility criteria to query capabilities of the repositories. We propose categories for study criteria corresponding to the effort needed for querying those criteria: “easy” (supporting automated queries), mixed (initial automated querying with manual review), “hard” (fully manual record review), and “impossible” or “point of enrollment” (not typically in health repositories). We obtained a sample of 292 criteria from 20 studies from ClinicalTrials.gov. Six independent reviewers, three each from two academic research institutions, rated criteria according to our four types. We observed high interrater reliability both within and between institutions. The analysis demonstrated typical features of criteria that map with varying levels of difficulty to repositories. We propose using these features to improve enrollment workflow through more standardized study criteria, self-service repository queries, and analyst-mediated retrievals. PMID:29854246

  12. Classification of Clinical Research Study Eligibility Criteria to Support Multi-Stage Cohort Identification Using Clinical Data Repositories.

    PubMed

    Cimino, James J; Lancaster, William J; Wyatt, Mathew C

    2017-01-01

    One of the challenges to using electronic health record (EHR) repositories for research is the difficulty mapping study subject eligibility criteria to the query capabilities of the repository. We sought to characterize criteria as "easy" (searchable in a typical repository), "hard" (requiring manual review of the record data), and "impossible" (not typically available in EHR repositories). We obtained 292 criteria from 20 studies available from Clinical Trials.gov and rated them according to our three types, plus a fourth "mixed" type. We had good agreement among three independent reviewers and chose 274 criteria that were characterized by single types for further analysis. The resulting analysis showed typical features of criteria that do and don't map to repositories. We propose that these features be used to guide researchers in specifying eligibility criteria to improve development of enrollment workflow, including the definition of EHR repository queries for self-service or analyst-mediated retrievals.

  13. 10 CFR 960.3-1-4-1 - Site identification as potentially acceptable.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Site identification as potentially acceptable. 960.3-1-4-1 Section 960.3-1-4-1 Energy DEPARTMENT OF ENERGY GENERAL GUIDELINES FOR THE PRELIMINARY SCREENING OF POTENTIAL SITES FOR A NUCLEAR WASTE REPOSITORY Implementation Guidelines § 960.3-1-4-1 Site identification...

  14. De-identification of Medical Images with Retention of Scientific Research Value

    PubMed Central

    Maffitt, David R.; Smith, Kirk E.; Kirby, Justin S.; Clark, Kenneth W.; Freymann, John B.; Vendt, Bruce A.; Tarbox, Lawrence R.; Prior, Fred W.

    2015-01-01

    Online public repositories for sharing research data allow investigators to validate existing research or perform secondary research without the expense of collecting new data. Patient data made publicly available through such repositories may constitute a breach of personally identifiable information if not properly de-identified. Imaging data are especially at risk because some intricacies of the Digital Imaging and Communications in Medicine (DICOM) format are not widely understood by researchers. If imaging data still containing protected health information (PHI) were released through a public repository, a number of different parties could be held liable, including the original researcher who collected and submitted the data, the original researcher’s institution, and the organization managing the repository. To minimize these risks through proper de-identification of image data, one must understand what PHI exists and where that PHI resides, and one must have the tools to remove PHI without compromising the scientific integrity of the data. DICOM public elements are defined by the DICOM Standard. Modality vendors use private elements to encode acquisition parameters that are not yet defined by the DICOM Standard, or the vendor may not have updated an existing software product after DICOM defined new public elements. Because private elements are not standardized, a common de-identification practice is to delete all private elements, removing scientifically useful data as well as PHI. Researchers and publishers of imaging data can use the tools and process described in this article to de-identify DICOM images according to current best practices. ©RSNA, 2015 PMID:25969931

  15. Large size MOEMS Fabry-Perot interferometer filter for focal plane array hyperspectral imaging

    NASA Astrophysics Data System (ADS)

    Chee, J.; Hwu, J.; Kim, T. S.; Kubby, J.; Velicu, S.; Gupta, N.

    2015-02-01

    Focal plane array (FPA) technology is mature and is widely used for imaging applications. However, FPAs have broadband responses which limit their ability to provide high performance in hyperspectral applications such as detection of buried explosives, and identifying the presence of explosive chemicals and their concentrations. EPIR is currently developing Micro-Opto-Electro-Mechanical System (MOEMS) Fabry-Perot interferometer filter (FPF) devices for FPAs. In this paper, we present our approach to MOEMS FPF design and fabrication that will meet the size requirements for large format FPA hyperspectral imaging. We also report the performance of our FPF resonance cavity, capable of up to 3 μm change gap in tens of nanometer increments.

  16. Gold nanoparticles and electroporation impose both separate and synergistic radiosensitizing effects in HT-29 tumor cells: an in vitro study.

    PubMed

    Rezaee, Zohre; Yadollahpour, Ali; Bayati, Vahid; Negad Dehbashi, Fereshteh

    2017-01-01

    Radiation therapy (RT) is the gold standard treatment for more than half of known tumors. Despite recent improvements in RT efficiency, the side effects of ionizing radiation (IR) in normal tissues are a dose-limiting factor that restricts higher doses in tumor treatment. One approach to enhance the efficiency of RT is the application of radiosensitizers to selectively increase the dose at the tumor site. Gold nanoparticles (GNPs) and electroporation (EP) have shown good potential as radiosensitizers for RT. This study aims to investigate the sensitizing effects of EP, GNPs, and combined GNPs-EP on the dose enhancement factor (DEF) for 6 MV photon energy. Radiosensitizing effects of EP, GNPs, and combinations of GNPs-EP were comparatively investigated in vitro for intestinal colon cancer (HT-29) and Chinese hamster ovary (CHO) cell lines by MTT assay and colony formation assay at 6 MV photon energy in six groups: IR (control group), GNPs+IR, GNPs (24 h)+IR, EP+IR, GNPs+EP+IR, and GNPs (24 h)+EP+IR. Treatment of both cell lines with EP, GNPs, and combined GNPs-EP significantly enhanced the response of cells to irradiation. However, the HT-29 showed higher DEF values for all groups. In addition, the DEF value for HT-29 cells for GNPs+IR, GNPs (24 h)+IR, EP+IR, GNPs+EP+IR, and GNPs (24 h)+EP+IR was, respectively, 1.17, 1.47, 1.36, 2.61, and 2.89, indicating synergistic radiosensitizing effect for the GNPs (24 h)+EP+IR group. Furthermore, the synergistic effect was observed just for HT-29 tumor cell lines. Combined GNPs-EP protocols induced synergistic radiosensitizing effect in HT-29 cells, and the effect is also tumor specific. This combined therapy can be beneficially used for the treatment of intrinsically less radiosensitive tumors.

  17. From GenBank to GBIF: Phylogeny-Based Predictive Niche Modeling Tests Accuracy of Taxonomic Identifications in Large Occurrence Data Repositories

    PubMed Central

    Smith, B. Eugene; Johnston, Mark K.; Lücking, Robert

    2016-01-01

    Accuracy of taxonomic identifications is crucial to data quality in online repositories of species occurrence data, such as the Global Biodiversity Information Facility (GBIF), which have accumulated several hundred million records over the past 15 years. These data serve as basis for large scale analyses of macroecological and biogeographic patterns and to document environmental changes over time. However, taxonomic identifications are often unreliable, especially for non-vascular plants and fungi including lichens, which may lack critical revisions of voucher specimens. Due to the scale of the problem, restudy of millions of collections is unrealistic and other strategies are needed. Here we propose to use verified, georeferenced occurrence data of a given species to apply predictive niche modeling that can then be used to evaluate unverified occurrences of that species. Selecting the charismatic lichen fungus, Usnea longissima, as a case study, we used georeferenced occurrence records based on sequenced specimens to model its predicted niche. Our results suggest that the target species is largely restricted to a narrow range of boreal and temperate forest in the Northern Hemisphere and that occurrence records in GBIF from tropical regions and the Southern Hemisphere do not represent this taxon, a prediction tested by comparison with taxonomic revisions of Usnea for these regions. As a novel approach, we employed Principal Component Analysis on the environmental grid data used for predictive modeling to visualize potential ecogeographical barriers for the target species; we found that tropical regions conform a strong barrier, explaining why potential niches in the Southern Hemisphere were not colonized by Usnea longissima and instead by morphologically similar species. This approach is an example of how data from two of the most important biodiversity repositories, GenBank and GBIF, can be effectively combined to remotely address the problem of inaccuracy of taxonomic identifications in occurrence data repositories and to provide a filtering mechanism which can considerably reduce the number of voucher specimens that need critical revision, in this case from 4,672 to about 100. PMID:26967999

  18. From GenBank to GBIF: Phylogeny-Based Predictive Niche Modeling Tests Accuracy of Taxonomic Identifications in Large Occurrence Data Repositories.

    PubMed

    Smith, B Eugene; Johnston, Mark K; Lücking, Robert

    2016-01-01

    Accuracy of taxonomic identifications is crucial to data quality in online repositories of species occurrence data, such as the Global Biodiversity Information Facility (GBIF), which have accumulated several hundred million records over the past 15 years. These data serve as basis for large scale analyses of macroecological and biogeographic patterns and to document environmental changes over time. However, taxonomic identifications are often unreliable, especially for non-vascular plants and fungi including lichens, which may lack critical revisions of voucher specimens. Due to the scale of the problem, restudy of millions of collections is unrealistic and other strategies are needed. Here we propose to use verified, georeferenced occurrence data of a given species to apply predictive niche modeling that can then be used to evaluate unverified occurrences of that species. Selecting the charismatic lichen fungus, Usnea longissima, as a case study, we used georeferenced occurrence records based on sequenced specimens to model its predicted niche. Our results suggest that the target species is largely restricted to a narrow range of boreal and temperate forest in the Northern Hemisphere and that occurrence records in GBIF from tropical regions and the Southern Hemisphere do not represent this taxon, a prediction tested by comparison with taxonomic revisions of Usnea for these regions. As a novel approach, we employed Principal Component Analysis on the environmental grid data used for predictive modeling to visualize potential ecogeographical barriers for the target species; we found that tropical regions conform a strong barrier, explaining why potential niches in the Southern Hemisphere were not colonized by Usnea longissima and instead by morphologically similar species. This approach is an example of how data from two of the most important biodiversity repositories, GenBank and GBIF, can be effectively combined to remotely address the problem of inaccuracy of taxonomic identifications in occurrence data repositories and to provide a filtering mechanism which can considerably reduce the number of voucher specimens that need critical revision, in this case from 4,672 to about 100.

  19. Design and application of a data-independent precursor and product ion repository.

    PubMed

    Thalassinos, Konstantinos; Vissers, Johannes P C; Tenzer, Stefan; Levin, Yishai; Thompson, J Will; Daniel, David; Mann, Darrin; DeLong, Mark R; Moseley, M Arthur; America, Antoine H; Ottens, Andrew K; Cavey, Greg S; Efstathiou, Georgios; Scrivens, James H; Langridge, James I; Geromanos, Scott J

    2012-10-01

    The functional design and application of a data-independent LC-MS precursor and product ion repository for protein identification, quantification, and validation is conceptually described. The ion repository was constructed from the sequence search results of a broad range of discovery experiments investigating various tissue types of two closely related mammalian species. The relative high degree of similarity in protein complement, ion detection, and peptide and protein identification allows for the analysis of normalized precursor and product ion intensity values, as well as standardized retention times, creating a multidimensional/orthogonal queryable, qualitative, and quantitative space. Peptide ion map selection for identification and quantification is primarily based on replication and limited variation. The information is stored in a relational database and is used to create peptide- and protein-specific fragment ion maps that can be queried in a targeted fashion against the raw or time aligned ion detections. These queries can be conducted either individually or as groups, where the latter affords pathway and molecular machinery analysis of the protein complement. The presented results also suggest that peptide ionization and fragmentation efficiencies are highly conserved between experiments and practically independent of the analyzed biological sample when using similar instrumentation. Moreover, the data illustrate only minor variation in ionization efficiency with amino acid sequence substitutions occurring between species. Finally, the data and the presented results illustrate how LC-MS performance metrics can be extracted and utilized to ensure optimal performance of the employed analytical workflows.

  20. Repository Profiles for Atmospheric and Climate Sciences: Capabilities and Trends in Data Services

    NASA Astrophysics Data System (ADS)

    Hou, C. Y.; Thompson, C. A.; Palmer, C. L.

    2014-12-01

    As digital research data proliferate and expectations for open access escalate, the landscape of data repositories is becoming more complex. For example, DataBib currently identifies 980 data repositories across the disciplines, with 117 categorized under Geosciences. In atmospheric and climate sciences, there are great expectations for the integration and reuse of data for advancing science. To realize this potential, resources are needed that explicate the range of repository options available for locating and depositing open data, their conditions of access and use, and the services and tools they provide. This study profiled 38 open digital repositories in the atmospheric and climate sciences, analyzing each on 55 criteria through content analysis of their websites. The results provide a systematic way to assess and compare capabilities, services, and institutional characteristics and identify trends across repositories. Selected results from the more detailed outcomes to be presented: Most repositories offer guidance on data format(s) for submission and dissemination. 42% offer authorization-free access. More than half use some type of data identification system such as DOIs. Nearly half offer some data processing, with a similar number providing software or tools. 78.9% request that users cite or acknowledge datasets used and the data center. Only 21.1% recommend specific metadata standards, such as ISO 19115 or Dublin Core, with more than half utilizing a customized metadata scheme. Information was rarely provided on repository certification and accreditation and uneven for transfer of rights and data security. Few provided policy information on preservation, migration, reappraisal, disposal, or long-term sustainability. As repository use increases, it will be important for institutions to make their procedures and policies explicit, to build trust with user communities and improve efficiencies in data sharing. Resources such as repository profiles will be essential for scientists to weigh options and understand trends in data services across the evolving network of repositories.

  1. The Use of Underground Research Laboratories to Support Repository Development Programs. A Roadmap for the Underground Research Facilities Network.

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    MacKinnon, Robert J.

    2015-10-26

    Under the auspices of the International Atomic Energy Agency (IAEA), nationally developed underground research laboratories (URLs) and associated research institutions are being offered for use by other nations. These facilities form an Underground Research Facilities (URF) Network for training in and demonstration of waste disposal technologies and the sharing of knowledge and experience related to geologic repository development, research, and engineering. In order to achieve its objectives, the URF Network regularly sponsors workshops and training events related to the knowledge base that is transferable between existing URL programs and to nations with an interest in developing a new URL. Thismore » report describes the role of URLs in the context of a general timeline for repository development. This description includes identification of key phases and activities that contribute to repository development as a repository program evolves from an early research and development phase to later phases such as construction, operations, and closure. This information is cast in the form of a matrix with the entries in this matrix forming the basis of the URF Network roadmap that will be used to identify and plan future workshops and training events.« less

  2. Estimation of Inventory Item Demand Distributions: Modeling Item Migration at the Defense Electronics Supply Center.

    DTIC Science & Technology

    1985-12-01

    LLEC𔃺,𔃾 PEAD(I.5E31 IFIRST 5 --: FJP ..... iEH,-, V 15)i :cN’ER, T’ COS’, J:.,. ATE EPiRE ... . F - 8E0P I. 1 PFSTC = :YEAR * : 65 , IPA 2 D.J’T FOF...RIL 0 209 1391 135 5 2 1741 ACTUAL 25 19 3262 196 2 0 3503 SIMULATED RIM 0 65 82 1456 125 40 1768 ACTUAL 13 16 236 1677 110 5 2057 SIMULATED RIHI 0 9...117 2540 149 22 2975 ACTUAL 6 61 220 1462 90 a 1847 SIMULATED RHl 0 10 1 70 700 117 899 ACTUAL 2 7 1 97 476 112 65 SIMULATED RIH2 0 5 0 0 12 1419 1436

  3. An Optimal Centralized Carbon Dioxide Repository for Florida, USA

    PubMed Central

    Poiencot, Brandon; Brown, Christopher

    2011-01-01

    For over a decade, the United States Department of Energy, and engineers, geologists, and scientists from all over the world have investigated the potential for reducing atmospheric carbon emissions through carbon sequestration. Numerous reports exist analyzing the potential for sequestering carbon dioxide at various sites around the globe, but none have identified the potential for a statewide system in Florida, USA. In 2005, 83% of Florida’s electrical energy was produced by natural gas, coal, or oil (e.g., fossil fuels), from power plants spread across the state. In addition, only limited research has been completed on evaluating optimal pipeline transportation networks to centralized carbon dioxide repositories. This paper describes the feasibility and preliminary locations for an optimal centralized Florida-wide carbon sequestration repository. Linear programming optimization modeling is used to plan and route an idealized pipeline network to existing Florida power plants. Further analysis of the subsurface geology in these general locations will provide insight into the suitability of the subsurface conditions and the available capacity for carbon sequestration at selected possible repository sites. The identification of the most favorable site(s) is also presented. PMID:21695024

  4. An optimal centralized carbon dioxide repository for Florida, USA.

    PubMed

    Poiencot, Brandon; Brown, Christopher

    2011-04-01

    For over a decade, the United States Department of Energy, and engineers, geologists, and scientists from all over the world have investigated the potential for reducing atmospheric carbon emissions through carbon sequestration. Numerous reports exist analyzing the potential for sequestering carbon dioxide at various sites around the globe, but none have identified the potential for a statewide system in Florida, USA. In 2005, 83% of Florida's electrical energy was produced by natural gas, coal, or oil (e.g., fossil fuels), from power plants spread across the state. In addition, only limited research has been completed on evaluating optimal pipeline transportation networks to centralized carbon dioxide repositories. This paper describes the feasibility and preliminary locations for an optimal centralized Florida-wide carbon sequestration repository. Linear programming optimization modeling is used to plan and route an idealized pipeline network to existing Florida power plants. Further analysis of the subsurface geology in these general locations will provide insight into the suitability of the subsurface conditions and the available capacity for carbon sequestration at selected possible repository sites. The identification of the most favorable site(s) is also presented.

  5. Use of 16S rRNA gene for identification of a broad range of clinically relevant bacterial pathogens

    DOE PAGES

    Srinivasan, Ramya; Karaoz, Ulas; Volegova, Marina; ...

    2015-02-06

    According to World Health Organization statistics of 2011, infectious diseases remain in the top five causes of mortality worldwide. However, despite sophisticated research tools for microbial detection, rapid and accurate molecular diagnostics for identification of infection in humans have not been extensively adopted. Time-consuming culture-based methods remain to the forefront of clinical microbial detection. The 16S rRNA gene, a molecular marker for identification of bacterial species, is ubiquitous to members of this domain and, thanks to ever-expanding databases of sequence information, a useful tool for bacterial identification. In this study, we assembled an extensive repository of clinical isolates (n =more » 617), representing 30 medically important pathogenic species and originally identified using traditional culture-based or non-16S molecular methods. This strain repository was used to systematically evaluate the ability of 16S rRNA for species level identification. To enable the most accurate species level classification based on the paucity of sequence data accumulated in public databases, we built a Naïve Bayes classifier representing a diverse set of high-quality sequences from medically important bacterial organisms. We show that for species identification, a model-based approach is superior to an alignment based method. Overall, between 16S gene based and clinical identities, our study shows a genus-level concordance rate of 96% and a species-level concordance rate of 87.5%. We point to multiple cases of probable clinical misidentification with traditional culture based identification across a wide range of gram-negative rods and gram-positive cocci as well as common gram-negative cocci.« less

  6. Use of 16S rRNA Gene for Identification of a Broad Range of Clinically Relevant Bacterial Pathogens

    PubMed Central

    Srinivasan, Ramya; Karaoz, Ulas; Volegova, Marina; MacKichan, Joanna; Kato-Maeda, Midori; Miller, Steve; Nadarajan, Rohan; Brodie, Eoin L.; Lynch, Susan V.

    2015-01-01

    According to World Health Organization statistics of 2011, infectious diseases remain in the top five causes of mortality worldwide. However, despite sophisticated research tools for microbial detection, rapid and accurate molecular diagnostics for identification of infection in humans have not been extensively adopted. Time-consuming culture-based methods remain to the forefront of clinical microbial detection. The 16S rRNA gene, a molecular marker for identification of bacterial species, is ubiquitous to members of this domain and, thanks to ever-expanding databases of sequence information, a useful tool for bacterial identification. In this study, we assembled an extensive repository of clinical isolates (n = 617), representing 30 medically important pathogenic species and originally identified using traditional culture-based or non-16S molecular methods. This strain repository was used to systematically evaluate the ability of 16S rRNA for species level identification. To enable the most accurate species level classification based on the paucity of sequence data accumulated in public databases, we built a Naïve Bayes classifier representing a diverse set of high-quality sequences from medically important bacterial organisms. We show that for species identification, a model-based approach is superior to an alignment based method. Overall, between 16S gene based and clinical identities, our study shows a genus-level concordance rate of 96% and a species-level concordance rate of 87.5%. We point to multiple cases of probable clinical misidentification with traditional culture based identification across a wide range of gram-negative rods and gram-positive cocci as well as common gram-negative cocci. PMID:25658760

  7. Proteomics data repositories: Providing a safe haven for your data and acting as a springboard for further research

    PubMed Central

    Vizcaíno, Juan Antonio; Foster, Joseph M.; Martens, Lennart

    2010-01-01

    Despite the fact that data deposition is not a generalised fact yet in the field of proteomics, several mass spectrometry (MS) based proteomics repositories are publicly available for the scientific community. The main existing resources are: the Global Proteome Machine Database (GPMDB), PeptideAtlas, the PRoteomics IDEntifications database (PRIDE), Tranche, and NCBI Peptidome. In this review the capabilities of each of these will be described, paying special attention to four key properties: data types stored, applicable data submission strategies, supported formats, and available data mining and visualization tools. Additionally, the data contents from model organisms will be enumerated for each resource. There are other valuable smaller and/or more specialized repositories but they will not be covered in this review. Finally, the concept behind the ProteomeXchange consortium, a collaborative effort among the main resources in the field, will be introduced. PMID:20615486

  8. Business Process Flow Diagrams in Tissue Bank Informatics System Design, and Identification and Communication of Best Practices: The Pharmaceutical Industry Experience.

    PubMed

    McDonald, Sandra A; Velasco, Elizabeth; Ilasi, Nicholas T

    2010-12-01

    Pfizer, Inc.'s Tissue Bank, in conjunction with Pfizer's BioBank (biofluid repository), endeavored to create an overarching internal software package to cover all general functions of both research facilities, including sample receipt, reconciliation, processing, storage, and ordering. Business process flow diagrams were developed by the Tissue Bank and Informatics teams as a way of characterizing best practices both within the Bank and in its interactions with key internal and external stakeholders. Besides serving as a first step for the software development, such formalized process maps greatly assisted the identification and communication of best practices and the optimization of current procedures. The diagrams shared here could assist other biospecimen research repositories (both pharmaceutical and other settings) for comparative purposes or as a guide to successful informatics design. Therefore, it is recommended that biorepositories consider establishing formalized business process flow diagrams for their laboratories, to address these objectives of communication and strategy.

  9. E-facts: business process management in clinical data repositories.

    PubMed

    Wattanasin, Nich; Peng, Zhaoping; Raine, Christine; Mitchell, Mariah; Wang, Charles; Murphy, Shawn N

    2008-11-06

    The Partners Healthcare Research Patient Data Registry (RPDR) is a centralized data repository that gathers clinical data from various hospital systems. The RPDR allows clinical investigators to obtain aggregate numbers of patients with user-defined characteristics such as diagnoses, procedures, medications, and laboratory values. They may then obtain patient identifiers and electronic medical records with prior IRB approval. Moreover, the accurate identification and efficient population of worthwhile and quantifiable facts from doctor's report into the RPDR is a significant process. As part of our ongoing e-Fact project, this work describes a new business process management technology that helps coordinate and simplify this procedure.

  10. Discovery of viruses and virus-like pathogens in pistachio using high-throughput sequencing

    USDA-ARS?s Scientific Manuscript database

    Pistachio (Pistacia vera L.) trees from the National Clonal Germplasm Repository (NCGR) and orchards in California were surveyed for viruses and virus-like agents by high-throughput sequencing (HTS). Analyses of 60 trees including clonal UCB-1 hybrid rootstock (P. atlantica × P. integerrima) identif...

  11. Automatic Content Recommendation and Aggregation According to SCORM

    ERIC Educational Resources Information Center

    Neves, Daniel Eugênio; Brandão, Wladmir Cardoso; Ishitani, Lucila

    2017-01-01

    Although widely used, the SCORM metadata model for content aggregation is difficult to be used by educators, content developers and instructional designers. Particularly, the identification of contents related with each other, in large repositories, and their aggregation using metadata as defined in SCORM, has been demanding efforts of computer…

  12. System Description and Status Report: California Education Information System.

    ERIC Educational Resources Information Center

    California State Dept. of Education, Sacramento.

    The California Education Information System (CEIS) consists of two subsystems of computer programs designed to process business and pupil data for local school districts. Creating and maintaining records concerning the students in the schools, the pupil subsystem provides for a central repository of school district identification information and a…

  13. [Intraarterial chemotherapy for uterine cervical adenocarcinoma: evaluation of its efficacy as neoadjuvant therapy].

    PubMed

    Usuki, N; Hirokawa, K; Tashiro, T; Saiwai, S; Miyamoto, T

    1999-10-01

    We performed preoperative intraarterial chemotherapy in twenty cases of uterine cervical adenocarcinoma (stage Ib: 2, II: 15, III: 3) and evaluated the efficacy of this therapy. The dosages used were 75-120 mg of CDDP, 10-20 mg of MMC and 30-60 mg of EPIR. These drugs were administered by intraarterial one-shot infusion twice every three weeks. In five cases, complete response (CR) of the primary lesion was confirmed by histologic examination. There were no cases of CR inpatients with well differentiated adenocarcinoma. Stage reduction was achieved in all cases except three. In all but one case, more than 50% volume reduction was recognized on MR images. These results were not significantly different from those in cases of uterine cervical squamous cell carcinoma in which we performed this therapy. Therefore, we concluded that intraarterial chemotherapy is highly effective and should be carried out as neoadjuvant therapy for advanced uterine cervical adenocarcinoma.

  14. Conventional and Real-Time PCRs for Detection of Erwinia piriflorinigrans Allow Its Distinction from the Fire Blight Pathogen, Erwinia amylovora

    PubMed Central

    Barbé, Silvia; Bertolini, Edson; Roselló, Montserrat; Llop, Pablo

    2014-01-01

    Erwinia piriflorinigrans is a new pathogenic species of the bacterial genus Erwinia that has been described recently in Spain. Accurate detection and identification of E. piriflorinigrans are challenging because its symptoms on pear blossoms are similar to those caused by Erwinia amylovora, the causal agent of fire blight. Moreover, these two species share phenotypic and molecular characteristics. Two specific and sensitive conventional and real-time PCR protocols were developed to identify and detect E. piriflorinigrans and to differentiate it from E. amylovora and other species of this genus. These protocols were based on sequences from plasmid pEPIR37, which is present in all strains of E. piriflorinigrans analyzed. After the stability of the plasmid was demonstrated, the specificities of the protocols were confirmed by the amplification of all E. piriflorinigrans strains tested, whereas 304 closely related pathogenic and nonpathogenic Erwinia strains and microbiota from pear trees were not amplified. In sensitivity assays, 103 cells/ml extract were detected in spiked plant material by conventional or real-time PCR, and 102 cells/ml were detected in DNA extracted from spiked plant material by real-time PCR. The protocols developed here succeeded in detecting E. piriflorinigrans in 102 out of 564 symptomatic and asymptomatic naturally infected pear samples (flowers, cortex stem tissue, leaves, shoots, and fruitlets), in necrotic Pyracantha sp. blossoms, and in necrotic pear and apple tissues infected with both E. amylovora and E. piriflorinigrans. Therefore, these new tools can be used in epidemiological studies that will enhance our understanding of the life cycle of E. piriflorinigrans in different hosts and plant tissues and its interaction with E. amylovora. PMID:24509928

  15. Conventional and real-time PCRs for detection of Erwinia piriflorinigrans allow its distinction from the fire blight pathogen, Erwinia amylovora.

    PubMed

    Barbé, Silvia; Bertolini, Edson; Roselló, Montserrat; Llop, Pablo; López, María M

    2014-04-01

    Erwinia piriflorinigrans is a new pathogenic species of the bacterial genus Erwinia that has been described recently in Spain. Accurate detection and identification of E. piriflorinigrans are challenging because its symptoms on pear blossoms are similar to those caused by Erwinia amylovora, the causal agent of fire blight. Moreover, these two species share phenotypic and molecular characteristics. Two specific and sensitive conventional and real-time PCR protocols were developed to identify and detect E. piriflorinigrans and to differentiate it from E. amylovora and other species of this genus. These protocols were based on sequences from plasmid pEPIR37, which is present in all strains of E. piriflorinigrans analyzed. After the stability of the plasmid was demonstrated, the specificities of the protocols were confirmed by the amplification of all E. piriflorinigrans strains tested, whereas 304 closely related pathogenic and nonpathogenic Erwinia strains and microbiota from pear trees were not amplified. In sensitivity assays, 10(3) cells/ml extract were detected in spiked plant material by conventional or real-time PCR, and 10(2) cells/ml were detected in DNA extracted from spiked plant material by real-time PCR. The protocols developed here succeeded in detecting E. piriflorinigrans in 102 out of 564 symptomatic and asymptomatic naturally infected pear samples (flowers, cortex stem tissue, leaves, shoots, and fruitlets), in necrotic Pyracantha sp. blossoms, and in necrotic pear and apple tissues infected with both E. amylovora and E. piriflorinigrans. Therefore, these new tools can be used in epidemiological studies that will enhance our understanding of the life cycle of E. piriflorinigrans in different hosts and plant tissues and its interaction with E. amylovora.

  16. [Tissue repositories for research at Sheba Medical Center(SMC].

    PubMed

    Cohen, Yehudit; Barshack, Iris; Onn, Amir

    2013-06-01

    Cancer is the number one cause of death in both genders. Breakthroughs in the understanding of cancer biology, the identification of prognostic factors, and the development of new treatments are increasingly dependent on access to human cancer tissues with linked clinicopathological data. Access to human tumor samples and a large investment in translational research are needed to advance this research. The SMC tissue repositories provide researchers with biological materials, which are essential tools for cancer research. SMC tissue repositories for research aim to collect, document and preserve human biospecimens from patients with cancerous diseases. This is in order to provide the highest quality and well annotated biological biospecimens, used as essential tools to achieve the growing demands of scientific research needs. Such repositories are partners in acceLerating biomedical research and medical product development through clinical resources, in order to apply best options to the patients. Following Institutional Review Board approval and signing an Informed Consent Form, the tumor and tumor-free specimens are coLLected by a designated pathologist at the operating room only when there is a sufficient amount of the tumor, in excess of the routine needs. Blood samples are collected prior to the procedure. Other types of specimens collected include ascites fluid, pleural effusion, tissues for Optimal Cutting Temperature [OCT] and primary culture etc. Demographic, clinical, pathologicaL, and follow-up data are collected in a designated database. SMC has already established several organ or disease-specific tissue repositories within different departments. The foundation of tissue repositories requires the concentrated effort of a multidisciplinary team composed of paramedical, medical and scientific professionals. Research projects using these specimens facilitate the development of 'targeted therapy', accelerate basic research aimed at clarifying molecular mechanisms involved in cancer, and support the development of novel diagnostic tools.

  17. TSPA 1991: An initial total-system performance assessment for Yucca Mountain; Yucca Mountain Site Characterization Project

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Barnard, R.W.; Wilson, M.L.; Dockery, H.A.

    1992-07-01

    This report describes an assessment of the long-term performance of a repository system that contains deeply buried highly radioactive waste; the system is assumed to be located at the potential site at Yucca Mountain, Nevada. The study includes an identification of features, events, and processes that might affect the potential repository, a construction of scenarios based on this identification, a selection of models describing these scenarios (including abstraction of appropriate models from detailed models), a selection of probability distributions for the parameters in the models, a stochastic calculation of radionuclide releases for the scenarios, and a derivation of complementary cumulativemore » distribution functions (CCDFs) for the releases. Releases and CCDFs are calculated for four categories of scenarios: aqueous flow (modeling primarily the existing conditions at the site, with allowances for climate change), gaseous flow, basaltic igneous activity, and human intrusion. The study shows that models of complex processes can be abstracted into more simplified representations that preserve the understanding of the processes and produce results consistent with those of more complex models.« less

  18. Sperm Cryopreservation in Live-Bearing Xiphophorus Fishes: Offspring Production from Xiphophorus variatus and Strategies for Establishment of Sperm Repositories

    PubMed Central

    Cuevas-Uribe, Rafael; Savage, Markita G.; Walter, Ronald B.; Tiersch, Terrence R.

    2012-01-01

    Abstract Cryopreservation of sperm from Xiphophorus fishes has produced live young in three species: X. hellerii, X. couchianus, and X. maculatus. In this study, the goal was to establish protocols for sperm cryopreservation and artificial insemination to produce live young in X. variatus, and to identify needs for repository development. The objectives were to: 1) collect basic biological characteristics of males; 2) cryopreserve sperm from X. variatus, 3) harvest live young from cryopreserved sperm, and 4) discuss the requirements for establishment of sperm repositories. The 35 males used in this study had a body weight of 0.298±0.096 g (mean±SD), body length of 2.5±0.2 cm, and testis weight of 6.4±3.4 mg. The sperm production per gram of testis was 2.33±1.32×109 cells. After freezing, the post-thaw motility decreased significantly to 37%±17% (ranging from 5% to 70%) (p=0.000) from 57%±14% (40%–80%) of fresh sperm (N=20). Artificial insemination of post-thaw sperm produced confirmed offspring from females of X. hellerii and X. variatus. This research, taken together with previous studies, provides a foundation for development of strategies for sperm repositories of Xiphophorus fishes. This includes: 1) the need for breeding strategies for regeneration of target populations, 2) identification of minimum fertilization capacity of frozen samples, 3) identification of fish numbers necessary for sampling and their genetic relationships, 4) selection of packaging containers for labeling and biosecurity, 5) assurance of quality control and standardization of procedures, 6) information systems that can manage the data associated with cryopreserved samples, including the genetic data, 7) biological data of sampled fish, 8) inventory data associated with frozen samples, and 9) data linking germplasm samples with other related materials such as body tissues or cells saved for DNA and RNA analyses. PMID:22924335

  19. Sperm cryopreservation in live-bearing Xiphophorus fishes: offspring production from Xiphophorus variatus and strategies for establishment of sperm repositories.

    PubMed

    Yang, Huiping; Cuevas-Uribe, Rafael; Savage, Markita G; Walter, Ronald B; Tiersch, Terrence R

    2012-09-01

    Cryopreservation of sperm from Xiphophorus fishes has produced live young in three species: X. hellerii, X. couchianus, and X. maculatus. In this study, the goal was to establish protocols for sperm cryopreservation and artificial insemination to produce live young in X. variatus, and to identify needs for repository development. The objectives were to: 1) collect basic biological characteristics of males; 2) cryopreserve sperm from X. variatus, 3) harvest live young from cryopreserved sperm, and 4) discuss the requirements for establishment of sperm repositories. The 35 males used in this study had a body weight of 0.298±0.096 g (mean±SD), body length of 2.5±0.2 cm, and testis weight of 6.4±3.4 mg. The sperm production per gram of testis was 2.33±1.32×10(9) cells. After freezing, the post-thaw motility decreased significantly to 37%±17% (ranging from 5% to 70%) (p=0.000) from 57%±14% (40%-80%) of fresh sperm (N=20). Artificial insemination of post-thaw sperm produced confirmed offspring from females of X. hellerii and X. variatus. This research, taken together with previous studies, provides a foundation for development of strategies for sperm repositories of Xiphophorus fishes. This includes: 1) the need for breeding strategies for regeneration of target populations, 2) identification of minimum fertilization capacity of frozen samples, 3) identification of fish numbers necessary for sampling and their genetic relationships, 4) selection of packaging containers for labeling and biosecurity, 5) assurance of quality control and standardization of procedures, 6) information systems that can manage the data associated with cryopreserved samples, including the genetic data, 7) biological data of sampled fish, 8) inventory data associated with frozen samples, and 9) data linking germplasm samples with other related materials such as body tissues or cells saved for DNA and RNA analyses.

  20. re3data.org - a global registry of research data repositories

    NASA Astrophysics Data System (ADS)

    Pampel, Heinz; Vierkant, Paul; Elger, Kirsten; Bertelmann, Roland; Witt, Michael; Schirmbacher, Peter; Rücknagel, Jessika; Kindling, Maxi; Scholze, Frank; Ulrich, Robert

    2016-04-01

    re3data.org - the registry of research data repositories lists over 1,400 research data repositories from all over the world making it the largest and most comprehensive online catalog of research data repositories on the web. The registry is a valuable tool for researchers, funding organizations, publishers and libraries. re3data.org provides detailed information about research data repositories, and its distinctive icons help researchers to easily identify relevant repositories for accessing and depositing data sets [1]. Funding agencies, like the European Commission [2] and research institutions like the University of Bielefeld [3] already recommend the use of re3data.org in their guidelines and policies. Several publishers and journals like Copernicus Publications, PeerJ, and Nature's Scientific Data recommend re3data.org in their editorial policies as a tool for the easy identification of appropriate data repositories to store research data. Project partners in re3data.org are the Library and Information Services department (LIS) of the GFZ German Research Centre for Geosciences, the Computer and Media Service at the Humboldt-Universität zu Berlin, the Purdue University Libraries and the KIT Library at the Karlsruhe Institute of Technology (KIT). After its fusion with the U.S. American DataBib in 2014, re3data.org continues as a service of DataCite from 2016 on. DataCite is the international organization for the registration of Digital Object Identifiers (DOI) for research data and aims to improve their citation. The poster describes the current status and the future plans of re3data.org. [1] Pampel H, et al. (2013) Making Research Data Repositories Visible: The re3data.org Registry. PLoS ONE 8(11): e78080. doi:10.1371/journal.pone.0078080. [2] European Commission (2015): Guidelines on Open Access to Scientific Publications and Research Data in Horizon 2020. Available: http://ec.europa.eu/research/participants/data/ref/h2020/grants_manual/hi/oa_pilot/h2020-hi-oa-pilot-guide_en.pdf Accessed 11 January 2016. [3] Bielefeld University (2013): Resolution on Research Data Management. Available: http://data.uni-bielefeld.de/en/resolution Accessed 11 January 2016.

  1. Packaging Strategies for Criticality Safety for "Other" DOE Fuels in a Repository

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Larry L Taylor

    2004-06-01

    Since 1998, there has been an ongoing effort to gain acceptance of U.S. Department of Energy (DOE)-owned spent nuclear fuel (SNF) in the national repository. To accomplish this goal, the fuel matrix was used as a discriminating feature to segregate fuels into nine distinct groups. From each of those groups, a characteristic fuel was selected and analyzed for criticality safety based on a proposed packaging strategy. This report identifies and quantifies the important criticality parameters for the canisterized fuels within each criticality group to: (1) demonstrate how the “other” fuels in the group are bounded by the baseline calculations ormore » (2) allow identification of individual type fuels that might require special analysis and packaging.« less

  2. The history of the USDA Nematode Collection and its database: valuable resources for taxonomic research and identification

    USDA-ARS?s Scientific Manuscript database

    The United States Department of Agriculture Nematode Collection continues to serve as one of the largest and most comprehensive nematode repositories in the world. Nematology research in the United States began in the late 1800’s, and for many years the collections of the USDA nematologists remained...

  3. Conservaton and retrieval of information

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Jensen, M.

    This is a summary of the findings of a Nordic working group formed in 1990 and given the task of establishing a basis for a common Nordic view of the need for information conservation for nuclear waste repositories by investigating the following: (1) the type of information that should be conserved; (2) the form in which the information should be kept; (3) the quality of the information as regards both type and form; and (4) the problems of future retrieval of information, including retrieval after very long periods of time. High-level waste from nuclear power generation will remain radioactive formore » very long times even though the major part of the radioactivity will have decayed within 1000 yr. Certain information about the waste must be kept for long time periods because future generations may-intentionally or inadvertently-come into contact with the radioactive waste. Current day waste management would benefit from an early identification of documents to be part of an archive for radioactive waste repositories. The same reasoning is valid for repositories for other toxic wastes.« less

  4. Data Portal | Office of Cancer Clinical Proteomics Research

    Cancer.gov

    The CPTAC Data Portal is a centralized repository for the public dissemination of proteomic sequence datasets collected by CPTAC, along with corresponding genomic sequence datasets.  In addition, available are analyses of CPTAC's raw mass spectrometry-based data files (mapping of spectra to peptide sequences and protein identification) by individual investigators from CPTAC and by a Common Data Analysis Pipeline.

  5. Cultivar identification and genetic relatedness among 25 black walnut (Juglans nigra) clones based on microsatellite markers

    Treesearch

    Kejia Pang; Keith Woeste; Charles Michler

    2017-01-01

    A set of eight microsatellite markers was used to genotype 25 black walnut (Juglans nigra L.) clones within the Purdue University germplasm repository. The identities of 212 ramets were verified using the same eight microsatellite markers. Some trees were mislabeled and corrected as to clone using analysis of microsatellite markers. A genetic...

  6. Electrical Resistance Tomography to Monitor Mitigation of Metal-Toxic Acid-Leachates Ruby Gulch Waste Rock Repository Gilt Edge Mine Superfund Site, South Dakota USA

    NASA Astrophysics Data System (ADS)

    Versteeg, R.; Heath, G.; Richardson, A.; Paul, D.; Wangerud, K.

    2003-12-01

    At a cyanide heap-leach open-pit mine, 15-million cubic yards of acid-generating sulfides were dumped at the head of a steep-walled mountain valley, with 30 inches/year precipitation generating 60- gallons/minute ARD leachate. Remediation has reshaped the dump to a 70-acre, 3.5:1-sloped geometry, installed drainage benches and runoff diversions, and capped the repository and lined diversions with a polyethylene geomembrane and cover system. Monitoring was needed to evaluate (a) long-term geomembrane integrity, (b) diversion liner integrity and long-term effectiveness, (c) ARD geochemistry, kinetics and pore-gas dynamics within the repository mass, and (d) groundwater interactions. Observation wells were paired with a 600-electrode resistivity survey system. Using near-surface and down-hole electrodes and automated data collection and post-processing, periodic two- and three-dimensional resistivity images are developed to reflect current and changed-conditions in moisture, temperature, geochemical components, and flow-direction analysis. Examination of total resistivity values and time variances between images allows direct observation of liner and cap integrity with precise identification and location of leaks; likewise, if runoff migrates from degraded diversion ditches into the repository zone, there is an accompanying and noticeable change in resistivity values. Used in combination with monitoring wells containing borehole resistivity electrodes (calibrated with direct sampling of dump water/moisture, temperature and pore-gas composition), the resistivity arrays allow at-depth imaging of geochemical conditions within the repository mass. The information provides early indications of progress or deficiencies in de-watering and ARD- mitigation that is the remedy intent. If emerging technologies present opportunities for secondary treatment, deep resistivity images may assist in developing application methods and evaluating the effectiveness of any reagents introduced into the repository mass to further effect changes in oxidation/reduction reactions.

  7. Materiel Solutions for Special Operations Forces

    DTIC Science & Technology

    2015-03-28

    Continually developed a repository of UNC System-wide defense research expertise and infrastructure resources to enable effective identification of UNC...antennas and more. • Mr. Jim Geurts, USSOCOM Acquisition Executive, visited the campuses of UNC Chapel Hill and NCSU in March 2013. He met with...game theory, and political science. The goal of the workshop was to explore cutting edge techniques to measure the effectiveness of special operations

  8. Detection and identification of Variola virus in fixed human tissue after prolonged archival storage.

    PubMed

    Schoepp, Randal J; Morin, Michelle D; Martinez, Mark J; Kulesh, David A; Hensley, Lisa; Geisbert, Thomas W; Brady, Daniel R; Jahrling, Peter B

    2004-01-01

    Smallpox disease has been eradicated from the human population since 1979, but is again a concern because of its potential use as an agent of bioterrorism or biowarfare. World Health Organization-sanctioned repositories of infectious Variola virus are known to occur in both Russia and the United States, but many believe other undeclared and unregulated sources of the virus could exist. Thus, validation of improved methods for definitive identification of smallpox virus in diagnostic specimens is urgently needed. In this paper, we describe the discovery of suspected Variola infected human tissue, fixed and preserved for decades in largely unknown solutions, and the use of routine histology, electron microscopy, and ultimately DNA extraction and fluorogenic 5' nuclease (TaqMan) assays for its identification and confirmation.

  9. The Pacific Northwest National Laboratory library of bacterial and archaeal proteomic biodiversity

    DOE PAGES

    Payne, Samuel H.; Monroe, Matthew E.; Overall, Christopher C.; ...

    2015-08-18

    This dataset deposition announces the submission to public repositories of the PNNL Biodiversity Library, a large collection of global proteomics data for 112 bacterial and archaeal organisms. The data comprises 35,162 tandem mass spectrometry (MS/MS) datasets from ~10 years of research. All data has been searched, annotated and organized in a consistent manner to promote reuse by the community. Protein identifications were cross-referenced with KEGG functional annotations which allows for pathway oriented investigation. We present the data as a freely available community resource. A variety of data re-use options are described for computational modeling, proteomics assay design and bioengineering. Instrumentmore » data and analysis files are available at ProteomeXchange via the MassIVE partner repository under the identifiers PXD001860 and MSV000079053.« less

  10. The Pacific Northwest National Laboratory library of bacterial and archaeal proteomic biodiversity

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Payne, Samuel H.; Monroe, Matthew E.; Overall, Christopher C.

    This dataset deposition announces the submission to public repositories of the PNNL Biodiversity Library, a large collection of global proteomics data for 112 bacterial and archaeal organisms. The data comprises 35,162 tandem mass spectrometry (MS/MS) datasets from ~10 years of research. All data has been searched, annotated and organized in a consistent manner to promote reuse by the community. Protein identifications were cross-referenced with KEGG functional annotations which allows for pathway oriented investigation. We present the data as a freely available community resource. A variety of data re-use options are described for computational modeling, proteomics assay design and bioengineering. Instrumentmore » data and analysis files are available at ProteomeXchange via the MassIVE partner repository under the identifiers PXD001860 and MSV000079053.« less

  11. Preservation of Earth Science Data History with Digital Content Repository Technology

    NASA Astrophysics Data System (ADS)

    Wei, Y.; Pan, J.; Shrestha, B.; Cook, R. B.

    2011-12-01

    An increasing need for derived and on-demand data product in Earth Science research makes the digital content more difficult for providers to manage and preserve and for users to locate, understand, and consume. Specifically, this increasing need presents additional challenges in managing data processing history information and delivering such information to end users. For example, the North American Carbon Program (NACP) Multi-scale Synthesis and Terrestrial Model Intercomparison Project (MsTMIP) chose a modified SYNMAP land cover data as one of the input driver data for participating terrestrial biospheric models. The global 1km resolution SYNMAP data was created by harmonizing 3 remote sensing-based land cover products: GLCC, GLC2000, and the MODIS land cover product. The original SYNMAP land cover data was aggregated into half and quarter degree resolution. It was then enhanced with more detailed grassland and cropland types. Currently, there lacks an effective mechanism to convey this data processing information to different modeling teams for them to determine if a data product meets their needs. It still highly relies on offline human interaction. The NASA-sponsored ORNL DAAC has leveraged the contemporary digital object repository technology to promote the representation, management, and delivery of data processing history and provenance information. Within digital object repository, different data products are managed as objects, with metadata as attributes and content delivery and management services as dissemination methods. Derivation relationships among data products can be semantically referenced between digital objects. Within the repository, data users can easily track a derived data product back to its origin, explorer metadata and documents about each intermediate data product, and discover processing details involved in each derivation step. Coupled with Drupal Web Content Management System, the digital repository interface was enhanced to provide intuitive graphic representation of the data processing history. Each data product is also associated with a formal metadata record in FGDC standards, and the main fields of the FGDC record are indexed for search, and are displayed as attributes of the data product. These features enable data users to better understand and consume a data product. The representation of data processing history in digital repository can further promote long-term data preservation. Lineage information is a major aspect to make digital data understandable and usable long time into the future. Derivation references can be setup between digital objects not only within a single digital repository, but also across multiple distributed digital repositories. Along with emerging identification mechanisms, such as Digital Object Identifier (DOI), a flexible distributed digital repository network can be setup to better preserve digital content. In this presentation, we describe how digital content repository technology can be used to manage, preserve, and deliver digital data processing history information in Earth Science research domain, with selected data archived in ORNL DAAC and Model and Synthesis Thematic Data Center (MAST-DC) as testing targets.

  12. Disaster victim identification of military aircrew, 1945-2002.

    PubMed

    Smith, Adrian

    2003-11-01

    Aviation accident fatalities are characterized by substantial tissue disruption and fragmentation, limiting the usefulness of traditional identification methods. This study examines the success of disaster victim identification (DVI) in military aviation accident fatalities in the Australian Defense Force (ADF). Accident reports and autopsy records of aircrew fatalities during the period 1945-2002 were examined to identify difficulties experienced during the DVI process or injuries that would prevent identification of remains using non-DNA methods. The ADF had 301 aircraft fatalities sustained in 144 accidents during the period 1945-2002. The autopsy reports for 117 fatalities were reviewed (covering 73.7% of aircrew fatalities from 1960-2002). Of the 117 victims, 38 (32.4%) sustained injuries which were severe enough to prevent identification by traditional (non-DNA) comparative scientific DVI techniques of fingerprint and dental analysis. Many of the ADF fatalities who could not be positively identified in the past could be identified today through the use of DNA techniques. Successful DNA identification, however, depends on having a reference DNA profile. This paper recommends the establishment of a DNA repository to store reference blood samples to facilitate the identification of ADF aircrew remains without causing additional distress to family members.

  13. Piloting a Deceased Subject Integrated Data Repository and Protecting Privacy of Relatives

    PubMed Central

    Huser, Vojtech; Kayaalp, Mehmet; Dodd, Zeyno A.; Cimino, James J.

    2014-01-01

    Use of deceased subject Electronic Health Records can be an important piloting platform for informatics or biomedical research. Existing legal framework allows such research under less strict de-identification criteria; however, privacy of non-decedent must be protected. We report on creation of the decease subject Integrated Data Repository (dsIDR) at National Institutes of Health, Clinical Center and a pilot methodology to remove secondary protected health information or identifiable information (secondary PxI; information about persons other than the primary patient). We characterize available structured coded data in dsIDR and report the estimated frequencies of secondary PxI, ranging from 12.9% (sensitive token presence) to 1.1% (using stricter criteria). Federating decedent EHR data from multiple institutions can address sample size limitations and our pilot study provides lessons learned and methodology that can be adopted by other institutions. PMID:25954378

  14. Piloting a deceased subject integrated data repository and protecting privacy of relatives.

    PubMed

    Huser, Vojtech; Kayaalp, Mehmet; Dodd, Zeyno A; Cimino, James J

    2014-01-01

    Use of deceased subject Electronic Health Records can be an important piloting platform for informatics or biomedical research. Existing legal framework allows such research under less strict de-identification criteria; however, privacy of non-decedent must be protected. We report on creation of the decease subject Integrated Data Repository (dsIDR) at National Institutes of Health, Clinical Center and a pilot methodology to remove secondary protected health information or identifiable information (secondary PxI; information about persons other than the primary patient). We characterize available structured coded data in dsIDR and report the estimated frequencies of secondary PxI, ranging from 12.9% (sensitive token presence) to 1.1% (using stricter criteria). Federating decedent EHR data from multiple institutions can address sample size limitations and our pilot study provides lessons learned and methodology that can be adopted by other institutions.

  15. Software architecture of the III/FBI segment of the FBI's integrated automated identification system

    NASA Astrophysics Data System (ADS)

    Booker, Brian T.

    1997-02-01

    This paper will describe the software architecture of the Interstate Identification Index (III/FBI) Segment of the FBI's Integrated Automated Fingerprint Identification System (IAFIS). IAFIS is currently under development, with deployment to begin in 1998. III/FBI will provide the repository of criminal history and photographs for criminal subjects, as well as identification data for military and civilian federal employees. Services provided by III/FBI include maintenance of the criminal and civil data, subject search of the criminal and civil data, and response generation services for IAFIS. III/FBI software will be comprised of both COTS and an estimated 250,000 lines of developed C code. This paper will describe the following: (1) the high-level requirements of the III/FBI software; (2) the decomposition of the III/FBI software into Computer Software Configuration Items (CSCIs); (3) the top-level design of the III/FBI CSCIs; and (4) the relationships among the developed CSCIs and the COTS products that will comprise the III/FBI software.

  16. Analysis of water flow paths: methodology and example calculations for a potential geological repository in Sweden.

    PubMed

    Werner, Kent; Bosson, Emma; Berglund, Sten

    2006-12-01

    Safety assessment related to the siting of a geological repository for spent nuclear fuel deep in the bedrock requires identification of potential flow paths and the associated travel times for radionuclides originating at repository depth. Using the Laxemar candidate site in Sweden as a case study, this paper describes modeling methodology, data integration, and the resulting water flow models, focusing on the Quaternary deposits and the upper 150 m of the bedrock. Example simulations identify flow paths to groundwater discharge areas and flow paths in the surface system. The majority of the simulated groundwater flow paths end up in the main surface waters and along the coastline, even though the particles used to trace the flow paths are introduced with a uniform spatial distribution at a relatively shallow depth. The calculated groundwater travel time, determining the time available for decay and retention of radionuclides, is on average longer to the coastal bays than to other biosphere objects at the site. Further, it is demonstrated how GIS-based modeling can be used to limit the number of surface flow paths that need to be characterized for safety assessment. Based on the results, the paper discusses an approach for coupling the present models to a model for groundwater flow in the deep bedrock.

  17. Data Independent Acquisition analysis in ProHits 4.0.

    PubMed

    Liu, Guomin; Knight, James D R; Zhang, Jian Ping; Tsou, Chih-Chiang; Wang, Jian; Lambert, Jean-Philippe; Larsen, Brett; Tyers, Mike; Raught, Brian; Bandeira, Nuno; Nesvizhskii, Alexey I; Choi, Hyungwon; Gingras, Anne-Claude

    2016-10-21

    Affinity purification coupled with mass spectrometry (AP-MS) is a powerful technique for the identification and quantification of physical interactions. AP-MS requires careful experimental design, appropriate control selection and quantitative workflows to successfully identify bona fide interactors amongst a large background of contaminants. We previously introduced ProHits, a Laboratory Information Management System for interaction proteomics, which tracks all samples in a mass spectrometry facility, initiates database searches and provides visualization tools for spectral counting-based AP-MS approaches. More recently, we implemented Significance Analysis of INTeractome (SAINT) within ProHits to provide scoring of interactions based on spectral counts. Here, we provide an update to ProHits to support Data Independent Acquisition (DIA) with identification software (DIA-Umpire and MSPLIT-DIA), quantification tools (through DIA-Umpire, or externally via targeted extraction), and assessment of quantitative enrichment (through mapDIA) and scoring of interactions (through SAINT-intensity). With additional improvements, notably support of the iProphet pipeline, facilitated deposition into ProteomeXchange repositories and enhanced export and viewing functions, ProHits 4.0 offers a comprehensive suite of tools to facilitate affinity proteomics studies. It remains challenging to score, annotate and analyze proteomics data in a transparent manner. ProHits was previously introduced as a LIMS to enable storing, tracking and analysis of standard AP-MS data. In this revised version, we expand ProHits to include integration with a number of identification and quantification tools based on Data-Independent Acquisition (DIA). ProHits 4.0 also facilitates data deposition into public repositories, and the transfer of data to new visualization tools. Copyright © 2016 Elsevier B.V. All rights reserved.

  18. Bioinformatics strategies in life sciences: from data processing and data warehousing to biological knowledge extraction.

    PubMed

    Thiele, Herbert; Glandorf, Jörg; Hufnagel, Peter

    2010-05-27

    With the large variety of Proteomics workflows, as well as the large variety of instruments and data-analysis software available, researchers today face major challenges validating and comparing their Proteomics data. Here we present a new generation of the ProteinScape bioinformatics platform, now enabling researchers to manage Proteomics data from the generation and data warehousing to a central data repository with a strong focus on the improved accuracy, reproducibility and comparability demanded by many researchers in the field. It addresses scientists; current needs in proteomics identification, quantification and validation. But producing large protein lists is not the end point in Proteomics, where one ultimately aims to answer specific questions about the biological condition or disease model of the analyzed sample. In this context, a new tool has been developed at the Spanish Centro Nacional de Biotecnologia Proteomics Facility termed PIKE (Protein information and Knowledge Extractor) that allows researchers to control, filter and access specific information from genomics and proteomic databases, to understand the role and relationships of the proteins identified in the experiments. Additionally, an EU funded project, ProDac, has coordinated systematic data collection in public standards-compliant repositories like PRIDE. This will cover all aspects from generating MS data in the laboratory, assembling the whole annotation information and storing it together with identifications in a standardised format.

  19. Using the Proteomics Identifications Database (PRIDE).

    PubMed

    Martens, Lennart; Jones, Phil; Côté, Richard

    2008-03-01

    The Proteomics Identifications Database (PRIDE) is a public data repository designed to store, disseminate, and analyze mass spectrometry based proteomics datasets. The PRIDE database can accommodate any level of detailed metadata about the submitted results, which can be queried, explored, viewed, or downloaded via the PRIDE Web interface. The PRIDE database also provides a simple, yet powerful, access control mechanism that fully supports confidential peer-reviewing of data related to a manuscript, ensuring that these results remain invisible to the general public while allowing referees and journal editors anonymized access to the data. This unit describes in detail the functionality that PRIDE provides with regards to searching, viewing, and comparing the available data, as well as different options for submitting data to PRIDE.

  20. Development of an Item Unique Identification Strategy for the Legacy Components of the US Marine Corps M1A1 Abrams Tank

    DTIC Science & Technology

    2008-12-03

    and efficiency) criteria will merit a high-risk designation . The DoD’s inventory management, later expanded in 2003 to include DoD supply chain...management,3 is not only one of the fourteen charter designations on the first high-risk list issued in 1993, it has also been on every biennial update...and logistics support data. Furthermore, the top-down design of the centralized information repository (IUID Registry) is perhaps the greatest

  1. Development of an Item Unique Identification Strategy for the Legacy Components of the US Marine Corps M1A1 Abrams Tank

    DTIC Science & Technology

    2008-12-01

    than $1 billion is at risk) and qualitative (i.e., significantly reduced effectiveness and efficiency) criteria will merit a high-risk designation ...management,3 is not only one of the fourteen charter designations on the first high- risk list issued in 1993, it has also been on every biennial...Furthermore, the top-down design of the centralized information repository (IUID Registry) is perhaps the greatest benefit of the IUID vision, as it

  2. The Philippine National Collection of Microorganisms (PNCM): Repository of microbial diversity of the country

    NASA Astrophysics Data System (ADS)

    Monsalud, R. G.; Magbanua, F. O.; Parungao, M. P.; Banaay, C. G. B.; Bayer, M. H. D.; Yap, J. K.; Tapay, L. M.

    2002-04-01

    The prime function of the Philippine National Collection of Microorganisms (PNCM), being the national repository of microbial strains, is to collect and preserve strains for their continued viability and availability for future use. To date, a total of 2144 strains of bacteria (1357), yeasts (250), filamentous, fungi (377), algae (14), and strains still to be identified (146) are maintained at the PNCM. These are preserved and maintained using various methods which include modified liquid drying (lyophilization), ultra-low temperature (-70°C) storage in 10% glycerol, storage in sterile soil, distilled water and overlaying with mineral oil. Periodic viability testing is done to assess the stability of these preserved cultures under storage. Aside from preservation and maintenance of cultures, the PNCM is also involved in several research activities. One of these is the isolation, characterization and identification of some Vibrio isolates from the Philippines. Details on this particular study is presented in this report.

  3. PDB-wide identification of biological assemblies from conserved quaternary structure geometry.

    PubMed

    Dey, Sucharita; Ritchie, David W; Levy, Emmanuel D

    2018-01-01

    Protein structures are key to understanding biomolecular mechanisms and diseases, yet their interpretation is hampered by limited knowledge of their biologically relevant quaternary structure (QS). A critical challenge in inferring QS information from crystallographic data is distinguishing biological interfaces from fortuitous crystal-packing contacts. Here, we tackled this problem by developing strategies for aligning and comparing QS states across both homologs and data repositories. QS conservation across homologs proved remarkably strong at predicting biological relevance and is implemented in two methods, QSalign and anti-QSalign, for annotating homo-oligomers and monomers, respectively. QS conservation across repositories is implemented in QSbio (http://www.QSbio.org), which approaches the accuracy of manual curation and allowed us to predict >100,000 QS states across the Protein Data Bank. Based on this high-quality data set, we analyzed pairs of structurally conserved interfaces, and this analysis revealed a striking plasticity whereby evolutionary distant interfaces maintain similar interaction geometries through widely divergent chemical properties.

  4. The ConSurf-DB: pre-calculated evolutionary conservation profiles of protein structures.

    PubMed

    Goldenberg, Ofir; Erez, Elana; Nimrod, Guy; Ben-Tal, Nir

    2009-01-01

    ConSurf-DB is a repository for evolutionary conservation analysis of the proteins of known structures in the Protein Data Bank (PDB). Sequence homologues of each of the PDB entries were collected and aligned using standard methods. The evolutionary conservation of each amino acid position in the alignment was calculated using the Rate4Site algorithm, implemented in the ConSurf web server. The algorithm takes into account the phylogenetic relations between the aligned proteins and the stochastic nature of the evolutionary process explicitly. Rate4Site assigns a conservation level for each position in the multiple sequence alignment using an empirical Bayesian inference. Visual inspection of the conservation patterns on the 3D structure often enables the identification of key residues that comprise the functionally important regions of the protein. The repository is updated with the latest PDB entries on a monthly basis and will be rebuilt annually. ConSurf-DB is available online at http://consurfdb.tau.ac.il/

  5. The ConSurf-DB: pre-calculated evolutionary conservation profiles of protein structures

    PubMed Central

    Goldenberg, Ofir; Erez, Elana; Nimrod, Guy; Ben-Tal, Nir

    2009-01-01

    ConSurf-DB is a repository for evolutionary conservation analysis of the proteins of known structures in the Protein Data Bank (PDB). Sequence homologues of each of the PDB entries were collected and aligned using standard methods. The evolutionary conservation of each amino acid position in the alignment was calculated using the Rate4Site algorithm, implemented in the ConSurf web server. The algorithm takes into account the phylogenetic relations between the aligned proteins and the stochastic nature of the evolutionary process explicitly. Rate4Site assigns a conservation level for each position in the multiple sequence alignment using an empirical Bayesian inference. Visual inspection of the conservation patterns on the 3D structure often enables the identification of key residues that comprise the functionally important regions of the protein. The repository is updated with the latest PDB entries on a monthly basis and will be rebuilt annually. ConSurf-DB is available online at http://consurfdb.tau.ac.il/ PMID:18971256

  6. Developing the Interstate Identification Index/Federal Bureau of Investigation (III/FBI) system for providing timely criminal and civil identification and criminal history information to the nation's law enforcement agencies

    NASA Astrophysics Data System (ADS)

    Copeland, Patricia L.; Shugars, James

    1997-02-01

    The Federal Bureau of Investigation (FBI) is currently developing a new system to provide timely criminal and civil identities and criminal history information to the nation's local, state, and federal users. The Integrated Automated Fingerprint Identification System (IAFIS), an upgrade to the existing Identification Division Automated Services (IDAS) System, is scheduled for implementation in 1999 at the new FBI facility in Clarksburg, West Virginia. IAFIS will offer new capabilities for electronic transmittal of fingerprint cards to the FBI, an improved fingerprint matching algorithm, and electronic maintenance of fingerprints and photo images. The Interstate Identification Index (III/FBI) System is one of three segments comprising the umbrella IAFIS System. III/FBI provides repository, maintenance, and dissemination capabilities for the 40 million subject national criminal history database. III/FBI will perform over 1 million name searches each day. Demanding performance, reliability/maintainability/availability, and flexibility/expandability requirements make III/FBI an architectural challenge to the system developers. This paper will discuss these driving requirements and present the technical solutions in terms of leading edge hardware and software.

  7. Milestones for Selection, Characterization, and Analysis of the Performance of a Repository for Spent Nuclear Fuel and High-Level Radioactive Waste at Yucca Mountain.

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Rechard, Robert P.

    This report presents a concise history in tabular form of events leading up to site identification in 1978, site selection in 1987, subsequent characterization, and ongoing analysis through 2008 of the performance of a repository for spent nuclear fuel and high-level radioactive waste at Yucca Mountain in southern Nevada. The tabulated events generally occurred in five periods: (1) commitment to mined geologic disposal and identification of sites; (2) site selection and analysis, based on regional geologic characterization through literature and analogous data; (3) feasibility analysis demonstrating calculation procedures and importance of system components, based on rough measures of performance usingmore » surface exploration, waste process knowledge, and general laboratory experiments; (4) suitability analysis demonstrating viability of disposal system, based on environment-specific laboratory experiments, in-situ experiments, and underground disposal system characterization; and (5) compliance analysis, based on completed site-specific characterization. Because the relationship is important to understanding the evolution of the Yucca Mountain Project, the tabulation also shows the interaction between four broad categories of political bodies and government agencies/institutions: (a) technical milestones of the implementing institutions, (b) development of the regulatory requirements and related federal policy in laws and court decisions, (c) Presidential and agency directives and decisions, and (d) critiques of the Yucca Mountain Project and pertinent national and world events related to nuclear energy and radioactive waste.« less

  8. HLRW management during MR reactor decommissioning in NRC 'Kurchatov Institute'

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Chesnokov, Alexander; Ivanov, Oleg; Kolyadin, Vyacheslav

    2013-07-01

    A program of decommissioning of MR research reactor in the Kurchatov institute started in 2008. The decommissioning work presumed a preliminary stage, which included: removal of spent fuel from near reactor storage; removal of spent fuel assemble of metal liquid loop channel from a core; identification, sorting and disposal of radioactive objects from gateway of the reactor; identification, sorting and disposal of radioactive objects from cells of HLRW storage of the Kurchatov institute for radwaste creating form the decommissioning of MR. All these works were performed by a remote controlled means with use of a remote identification methods of highmore » radioactive objects. A distribution of activity along high radiated objects was measured by a collimated radiometer installed on the robot Brokk-90, a gamma image of the object was registered by gamma-visor. Spectrum of gamma radiation was measured by a gamma locator and semiconductor detector system. For identification of a presence of uranium isotopes in the HLRW a technique, based on the registration of characteristic radiation of U, was developed. For fragmentation of high radiated objects was used a cold cutting technique and dust suppression system was applied for reduction of volume activity of aerosols in air. The management of HLRW was performed by remote controlled robots Brokk-180 and Brokk-330. They executed sorting, cutting and parking of high radiated part of contaminated equipment. The use of these techniques allowed to reduce individual and collective doses of personal performed the decommissioning. The average individual dose of the personnel was 1,9 mSv/year in 2011, and the collective dose is estimated by 0,0605 man x Sv/year. Use of the remote control machines enables reducing the number of working personal (20 men) and doses. X-ray spectrometric methods enable determination of a presence of the U in high radiated objects and special cans and separation of them for further spent fuel inspection. The sorting of radwaste enabled shipping of the LLRW and ILRW to special repositories and keeping of the HLRW for decay in the Kurchatov institute repository. (authors)« less

  9. Shuttle Ground Operations Efficiencies/Technologies Study (SGOE/T). Volume 5: Technical Information Sheets (TIS)

    NASA Technical Reports Server (NTRS)

    Scholz, A. L.; Hart, M. T.; Lowry, D. J.

    1987-01-01

    The Technology Information Sheet was assembled in database format during Phase I. This document was designed to provide a repository for information pertaining to 144 Operations and Maintenance Instructions (OMI) controlled operations in the Orbiter Processing Facility (OPF), Vehicle Assembly Building (VAB), and PAD. It provides a way to accumulate information about required crew sizes, operations task time duration (serial and/or parallel), special Ground Support Equipment (GSE). required, and identification of a potential application of existing technology or the need for the development of a new technolgoy item.

  10. An update on sORFs.org: a repository of small ORFs identified by ribosome profiling.

    PubMed

    Olexiouk, Volodimir; Van Criekinge, Wim; Menschaert, Gerben

    2018-01-04

    sORFs.org (http://www.sorfs.org) is a public repository of small open reading frames (sORFs) identified by ribosome profiling (RIBO-seq). This update elaborates on the major improvements implemented since its initial release. sORFs.org now additionally supports three more species (zebrafish, rat and Caenorhabditis elegans) and currently includes 78 RIBO-seq datasets, a vast increase compared to the three that were processed in the initial release. Therefore, a novel pipeline was constructed that also enables sORF detection in RIBO-seq datasets comprising solely elongating RIBO-seq data while previously, matching initiating RIBO-seq data was necessary to delineate the sORFs. Furthermore, a novel noise filtering algorithm was designed, able to distinguish sORFs with true ribosomal activity from simulated noise, consequently reducing the false positive identification rate. The inclusion of other species also led to the development of an inner BLAST pipeline, assessing sequence similarity between sORFs in the repository. Building on the proof of concept model in the initial release of sORFs.org, a full PRIDE-ReSpin pipeline was now released, reprocessing publicly available MS-based proteomics PRIDE datasets, reporting on true translation events. Next to reporting those identified peptides, sORFs.org allows visual inspection of the annotated spectra within the Lorikeet MS/MS viewer, thus enabling detailed manual inspection and interpretation. © The Author(s) 2017. Published by Oxford University Press on behalf of Nucleic Acids Research.

  11. A standardized framing for reporting protein identifications in mzIdentML 1.2

    PubMed Central

    Seymour, Sean L.; Farrah, Terry; Binz, Pierre-Alain; Chalkley, Robert J.; Cottrell, John S.; Searle, Brian C.; Tabb, David L.; Vizcaíno, Juan Antonio; Prieto, Gorka; Uszkoreit, Julian; Eisenacher, Martin; Martínez-Bartolomé, Salvador; Ghali, Fawaz; Jones, Andrew R.

    2015-01-01

    Inferring which protein species have been detected in bottom-up proteomics experiments has been a challenging problem for which solutions have been maturing over the past decade. While many inference approaches now function well in isolation, comparing and reconciling the results generated across different tools remains difficult. It presently stands as one of the greatest barriers in collaborative efforts such as the Human Proteome Project and public repositories like the PRoteomics IDEntifications (PRIDE) database. Here we present a framework for reporting protein identifications that seeks to improve capabilities for comparing results generated by different inference tools. This framework standardizes the terminology for describing protein identification results, associated with the HUPO-Proteomics Standards Initiative (PSI) mzIdentML standard, while still allowing for differing methodologies to reach that final state. It is proposed that developers of software for reporting identification results will adopt this terminology in their outputs. While the new terminology does not require any changes to the core mzIdentML model, it represents a significant change in practice, and, as such, the rules will be released via a new version of the mzIdentML specification (version 1.2) so that consumers of files are able to determine whether the new guidelines have been adopted by export software. PMID:25092112

  12. From barcoding single individuals to metabarcoding biological communities: towards an integrative approach to the study of global biodiversity.

    PubMed

    Cristescu, Melania E

    2014-10-01

    DNA-based species identification, known as barcoding, transformed the traditional approach to the study of biodiversity science. The field is transitioning from barcoding individuals to metabarcoding communities. This revolution involves new sequencing technologies, bioinformatics pipelines, computational infrastructure, and experimental designs. In this dynamic genomics landscape, metabarcoding studies remain insular and biodiversity estimates depend on the particular methods used. In this opinion article, I discuss the need for a coordinated advancement of DNA-based species identification that integrates taxonomic and barcoding information. Such an approach would facilitate access to almost 3 centuries of taxonomic knowledge and 1 decade of building repository barcodes. Conservation projects are time sensitive, research funding is becoming restricted, and informed decisions depend on our ability to embrace integrative approaches to biodiversity science. Copyright © 2014 Elsevier Ltd. All rights reserved.

  13. Ligandbook: an online repository for small and drug-like molecule force field parameters.

    PubMed

    Domanski, Jan; Beckstein, Oliver; Iorga, Bogdan I

    2017-06-01

    Ligandbook is a public database and archive for force field parameters of small and drug-like molecules. It is a repository for parameter sets that are part of published work but are not easily available to the community otherwise. Parameter sets can be downloaded and immediately used in molecular dynamics simulations. The sets of parameters are versioned with full histories and carry unique identifiers to facilitate reproducible research. Text-based search on rich metadata and chemical substructure search allow precise identification of desired compounds or functional groups. Ligandbook enables the rapid set up of reproducible molecular dynamics simulations of ligands and protein-ligand complexes. Ligandbook is available online at https://ligandbook.org and supports all modern browsers. Parameters can be searched and downloaded without registration, including access through a programmatic RESTful API. Deposition of files requires free user registration. Ligandbook is implemented in the PHP Symfony2 framework with TCL scripts using the CACTVS toolkit. oliver.beckstein@asu.edu or bogdan.iorga@cnrs.fr ; contact@ligandbook.org . Supplementary data are available at Bioinformatics online. © The Author 2017. Published by Oxford University Press.

  14. Citing geospatial feature inventories with XML manifests

    NASA Astrophysics Data System (ADS)

    Bose, R.; McGarva, G.

    2006-12-01

    Today published scientific papers include a growing number of citations for online information sources that either complement or replace printed journals and books. We anticipate this same trend for cartographic citations used in the geosciences, following advances in web mapping and geographic feature-based services. Instead of using traditional libraries to resolve citations for print material, the geospatial citation life cycle will include requesting inventories of objects or geographic features from distributed geospatial data repositories. Using a case study from the UK Ordnance Survey MasterMap database, which is illustrative of geographic object-based products in general, we propose citing inventories of geographic objects using XML feature manifests. These manifests: (1) serve as a portable listing of sets of versioned features; (2) could be used as citations within the identification portion of an international geospatial metadata standard; (3) could be incorporated into geospatial data transfer formats such as GML; but (4) can be resolved only with comprehensive, curated repositories of current and historic data. This work has implications for any researcher who foresees the need to make or resolve references to online geospatial databases.

  15. Fundamental Data Standards for Science Data System Interoperability and Data Correlation

    NASA Astrophysics Data System (ADS)

    Hughes, J. Steven; Gopala Krishna, Barla; Rye, Elizabeth; Crichton, Daniel

    The advent of the Web and languages such as XML have brought an explosion of online science data repositories and the promises of correlated data and interoperable systems. However there have been relatively few successes in meeting the expectations of science users in the internet age. For example a Google-like search for images of Mars will return many highly-derived and appropriately tagged images but largely ignore the majority of images in most online image repositories. Once retrieved, users are further frustrated by poor data descriptions, arcane formats, and badly organized ancillary information. A wealth of research indicates that shared information models are needed to enable system interoperability and data correlation. However, at a more fundamental level, data correlation and system interoperability are dependant on a relatively few shared data standards. A com-mon data dictionary standard, for example, allows the controlled vocabulary used in a science repository to be shared with potential collaborators. Common data registry and product iden-tification standards enable systems to efficiently find, locate, and retrieve data products and their metadata from remote repositories. Information content standards define categories of descriptive data that help make the data products scientifically useful to users who were not part of the original team that produced the data. The Planetary Data System (PDS) has a plan to move the PDS to a fully online, federated system. This plan addresses new demands on the system including increasing data volume, numbers of missions, and complexity of missions. A key component of this plan is the upgrade of the PDS Data Standards. The adoption of the core PDS data standards by the International Planetary Data Alliance (IPDA) adds the element of international cooperation to the plan. This presentation will provide an overview of the fundamental data standards being adopted by the PDS that transcend science domains and that will help to meet the PDS's and IPDA's system interoperability and data correlation requirements.

  16. Grid Application Meta-Repository System: Repository Interconnectivity and Cross-domain Application Usage in Distributed Computing Environments

    NASA Astrophysics Data System (ADS)

    Tudose, Alexandru; Terstyansky, Gabor; Kacsuk, Peter; Winter, Stephen

    Grid Application Repositories vary greatly in terms of access interface, security system, implementation technology, communication protocols and repository model. This diversity has become a significant limitation in terms of interoperability and inter-repository access. This paper presents the Grid Application Meta-Repository System (GAMRS) as a solution that offers better options for the management of Grid applications. GAMRS proposes a generic repository architecture, which allows any Grid Application Repository (GAR) to be connected to the system independent of their underlying technology. It also presents applications in a uniform manner and makes applications from all connected repositories visible to web search engines, OGSI/WSRF Grid Services and other OAI (Open Archive Initiative)-compliant repositories. GAMRS can also function as a repository in its own right and can store applications under a new repository model. With the help of this model, applications can be presented as embedded in virtual machines (VM) and therefore they can be run in their native environments and can easily be deployed on virtualized infrastructures allowing interoperability with new generation technologies such as cloud computing, application-on-demand, automatic service/application deployments and automatic VM generation.

  17. Leveraging of Open EMR Architecture for Clinical Trial Accrual

    PubMed Central

    Afrin, Lawrence B.; Oates, James C.; Boyd, Caroline K.; Daniels, Mark S.

    2003-01-01

    Accrual to clinical trials is a major bottleneck in scientific progress in clinical medicine. Many methods for identifying potential subjects and improving accrual have been pursued; few have succeeded, and none have proven generally reproducible or scalable. We leveraged the open architecture of the core clinical data repository of our electronic medical record system to prototype a solution for this problem in a manner consistent with contemporary regulations and research ethics. We piloted the solution with a local investigator-initiated trial for which candidate identification was expected to be difficult. Key results in the eleven months of experience to date include automated screening of 7,296,708 lab results from 69,288 patients, detection of 1,768 screening tests of interest, identification of 70 potential candidates who met all further automated criteria, and accrual of three candidates to the trial. Hypotheses for this disappointing impact on accrual, and directions for future research, are discussed. PMID:14728125

  18. Mass spectrometry data from label-free quantitative proteomic analysis of harmless and pathogenic strains of infectious microalgae, Prototheca spp.

    PubMed

    Murugaiyan, Jayaseelan; Eravci, Murat; Weise, Christoph; Roesler, Uwe

    2017-06-01

    Here, we provide the dataset associated with our research article 'label-free quantitative proteomic analysis of harmless and pathogenic strains of infectious microalgae, Prototheca spp.' (Murugaiyan et al., 2017) [1]. This dataset describes liquid chromatography-mass spectrometry (LC-MS)-based protein identification and quantification of a non-infectious strain, Prototheca zopfii genotype 1 and two strains associated with severe and mild infections, respectively, P. zopfii genotype 2 and Prototheca blaschkeae . Protein identification and label-free quantification was carried out by analysing MS raw data using the MaxQuant-Andromeda software suit. The expressional level differences of the identified proteins among the strains were computed using Perseus software and the results were presented in [1]. This DiB provides the MaxQuant output file and raw data deposited in the PRIDE repository with the dataset identifier PXD005305.

  19. 48 CFR 227.7207 - Contractor data repositories.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... Computer Software and Computer Software Documentation 227.7207 Contractor data repositories. Follow 227.7108 when it is in the Government's interests to have a data repository include computer software or to have a separate computer software repository. Contractual instruments establishing the repository...

  20. 48 CFR 227.7207 - Contractor data repositories.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... Computer Software and Computer Software Documentation 227.7207 Contractor data repositories. Follow 227.7108 when it is in the Government's interests to have a data repository include computer software or to have a separate computer software repository. Contractual instruments establishing the repository...

  1. 48 CFR 227.7207 - Contractor data repositories.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... Computer Software and Computer Software Documentation 227.7207 Contractor data repositories. Follow 227.7108 when it is in the Government's interests to have a data repository include computer software or to have a separate computer software repository. Contractual instruments establishing the repository...

  2. 48 CFR 227.7207 - Contractor data repositories.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... Computer Software and Computer Software Documentation 227.7207 Contractor data repositories. Follow 227.7108 when it is in the Government's interests to have a data repository include computer software or to have a separate computer software repository. Contractual instruments establishing the repository...

  3. Automated Cancer Registry Notifications: Validation of a Medical Text Analytics System for Identifying Patients with Cancer from a State-Wide Pathology Repository

    PubMed Central

    Nguyen, Anthony N; Moore, Julie; O'Dwyer, John; Philpot, Shoni

    2016-01-01

    The paper assesses the utility of Medtex on automating Cancer Registry notifications from narrative histology and cytology reports from the Queensland state-wide pathology information system. A corpus of 45.3 million pathology HL7 messages (including 119,581 histology and cytology reports) from a Queensland pathology repository for the year of 2009 was analysed by Medtex for cancer notification. Reports analysed by Medtex were consolidated at a patient level and compared against patients with notifiable cancers from the Queensland Oncology Repository (QOR). A stratified random sample of 1,000 patients was manually reviewed by a cancer clinical coder to analyse agreements and discrepancies. Sensitivity of 96.5% (95% confidence interval: 94.5-97.8%), specificity of 96.5% (95.3-97.4%) and positive predictive value of 83.7% (79.6-86.8%) were achieved for identifying cancer notifiable patients. Medtex achieved high sensitivity and specificity across the breadth of cancers, report types, pathology laboratories and pathologists throughout the State of Queensland. The high sensitivity also resulted in the identification of cancer patients that were not found in the QOR. High sensitivity was at the expense of positive predictive value; however, these cases may be considered as lower priority to Cancer Registries as they can be quickly reviewed. Error analysis revealed that system errors tended to be tumour stream dependent. Medtex is proving to be a promising medical text analytic system. High value cancer information can be generated through intelligent data classification and extraction on large volumes of unstructured pathology reports. PMID:28269893

  4. Automated Cancer Registry Notifications: Validation of a Medical Text Analytics System for Identifying Patients with Cancer from a State-Wide Pathology Repository.

    PubMed

    Nguyen, Anthony N; Moore, Julie; O'Dwyer, John; Philpot, Shoni

    2016-01-01

    The paper assesses the utility of Medtex on automating Cancer Registry notifications from narrative histology and cytology reports from the Queensland state-wide pathology information system. A corpus of 45.3 million pathology HL7 messages (including 119,581 histology and cytology reports) from a Queensland pathology repository for the year of 2009 was analysed by Medtex for cancer notification. Reports analysed by Medtex were consolidated at a patient level and compared against patients with notifiable cancers from the Queensland Oncology Repository (QOR). A stratified random sample of 1,000 patients was manually reviewed by a cancer clinical coder to analyse agreements and discrepancies. Sensitivity of 96.5% (95% confidence interval: 94.5-97.8%), specificity of 96.5% (95.3-97.4%) and positive predictive value of 83.7% (79.6-86.8%) were achieved for identifying cancer notifiable patients. Medtex achieved high sensitivity and specificity across the breadth of cancers, report types, pathology laboratories and pathologists throughout the State of Queensland. The high sensitivity also resulted in the identification of cancer patients that were not found in the QOR. High sensitivity was at the expense of positive predictive value; however, these cases may be considered as lower priority to Cancer Registries as they can be quickly reviewed. Error analysis revealed that system errors tended to be tumour stream dependent. Medtex is proving to be a promising medical text analytic system. High value cancer information can be generated through intelligent data classification and extraction on large volumes of unstructured pathology reports.

  5. Warehousing re-annotated cancer genes for biomarker meta-analysis.

    PubMed

    Orsini, M; Travaglione, A; Capobianco, E

    2013-07-01

    Translational research in cancer genomics assigns a fundamental role to bioinformatics in support of candidate gene prioritization with regard to both biomarker discovery and target identification for drug development. Efforts in both such directions rely on the existence and constant update of large repositories of gene expression data and omics records obtained from a variety of experiments. Users who interactively interrogate such repositories may have problems in retrieving sample fields that present limited associated information, due for instance to incomplete entries or sometimes unusable files. Cancer-specific data sources present similar problems. Given that source integration usually improves data quality, one of the objectives is keeping the computational complexity sufficiently low to allow an optimal assimilation and mining of all the information. In particular, the scope of integrating intraomics data can be to improve the exploration of gene co-expression landscapes, while the scope of integrating interomics sources can be that of establishing genotype-phenotype associations. Both integrations are relevant to cancer biomarker meta-analysis, as the proposed study demonstrates. Our approach is based on re-annotating cancer-specific data available at the EBI's ArrayExpress repository and building a data warehouse aimed to biomarker discovery and validation studies. Cancer genes are organized by tissue with biomedical and clinical evidences combined to increase reproducibility and consistency of results. For better comparative evaluation, multiple queries have been designed to efficiently address all types of experiments and platforms, and allow for retrieval of sample-related information, such as cell line, disease state and clinical aspects. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

  6. 40 CFR 124.33 - Information repository.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 21 2010-07-01 2010-07-01 false Information repository. 124.33 Section... FOR DECISIONMAKING Specific Procedures Applicable to RCRA Permits § 124.33 Information repository. (a... basis, for an information repository. When assessing the need for an information repository, the...

  7. 10 CFR 60.130 - General considerations.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REPOSITORIES Technical Criteria Design Criteria for the Geologic Repository Operations Area § 60.130 General... for a high-level radioactive waste repository at a geologic repository operations area, and an... geologic repository operations area, must include the principal design criteria for a proposed facility...

  8. 48 CFR 227.7108 - Contractor data repositories.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Technical Data 227.7108 Contractor data repositories. (a) Contractor data repositories may be established... procedures for protecting technical data delivered to or stored at the repository from unauthorized release... disclosure of technical data from the repository to third parties consistent with the Government's rights in...

  9. 17 CFR 49.12 - Swap data repository recordkeeping requirements.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 17 Commodity and Securities Exchanges 1 2012-04-01 2012-04-01 false Swap data repository... COMMISSION SWAP DATA REPOSITORIES § 49.12 Swap data repository recordkeeping requirements. (a) A registered swap data repository shall maintain its books and records in accordance with the requirements of part...

  10. 17 CFR 49.12 - Swap data repository recordkeeping requirements.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 17 Commodity and Securities Exchanges 1 2013-04-01 2013-04-01 false Swap data repository... COMMISSION SWAP DATA REPOSITORIES § 49.12 Swap data repository recordkeeping requirements. (a) A registered swap data repository shall maintain its books and records in accordance with the requirements of part...

  11. 17 CFR 49.12 - Swap data repository recordkeeping requirements.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 17 Commodity and Securities Exchanges 2 2014-04-01 2014-04-01 false Swap data repository... COMMISSION (CONTINUED) SWAP DATA REPOSITORIES § 49.12 Swap data repository recordkeeping requirements. (a) A registered swap data repository shall maintain its books and records in accordance with the requirements of...

  12. 10 CFR 63.112 - Requirements for preclosure safety analysis of the geologic repository operations area.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... geologic repository operations area. 63.112 Section 63.112 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN A GEOLOGIC REPOSITORY AT YUCCA MOUNTAIN, NEVADA Technical... repository operations area. The preclosure safety analysis of the geologic repository operations area must...

  13. Managing and Evaluating Digital Repositories

    ERIC Educational Resources Information Center

    Zuccala, Alesia; Oppenheim, Charles; Dhiensa, Rajveen

    2008-01-01

    Introduction: We examine the role of the digital repository manager, discuss the future of repository management and evaluation and suggest that library and information science schools develop new repository management curricula. Method: Face-to-face interviews were carried out with managers of five different types of repositories and a Web-based…

  14. jPOSTrepo: an international standard data repository for proteomes

    PubMed Central

    Okuda, Shujiro; Watanabe, Yu; Moriya, Yuki; Kawano, Shin; Yamamoto, Tadashi; Matsumoto, Masaki; Takami, Tomoyo; Kobayashi, Daiki; Araki, Norie; Yoshizawa, Akiyasu C.; Tabata, Tsuyoshi; Sugiyama, Naoyuki; Goto, Susumu; Ishihama, Yasushi

    2017-01-01

    Major advancements have recently been made in mass spectrometry-based proteomics, yielding an increasing number of datasets from various proteomics projects worldwide. In order to facilitate the sharing and reuse of promising datasets, it is important to construct appropriate, high-quality public data repositories. jPOSTrepo (https://repository.jpostdb.org/) has successfully implemented several unique features, including high-speed file uploading, flexible file management and easy-to-use interfaces. This repository has been launched as a public repository containing various proteomic datasets and is available for researchers worldwide. In addition, our repository has joined the ProteomeXchange consortium, which includes the most popular public repositories such as PRIDE in Europe for MS/MS datasets and PASSEL for SRM datasets in the USA. Later MassIVE was introduced in the USA and accepted into the ProteomeXchange, as was our repository in July 2016, providing important datasets from Asia/Oceania. Accordingly, this repository thus contributes to a global alliance to share and store all datasets from a wide variety of proteomics experiments. Thus, the repository is expected to become a major repository, particularly for data collected in the Asia/Oceania region. PMID:27899654

  15. A distributed computational search strategy for the identification of diagnostics targets: application to finding aptamer targets for methicillin-resistant staphylococci.

    PubMed

    Flanagan, Keith; Cockell, Simon; Harwood, Colin; Hallinan, Jennifer; Nakjang, Sirintra; Lawry, Beth; Wipat, Anil

    2014-06-30

    The rapid and cost-effective identification of bacterial species is crucial, especially for clinical diagnosis and treatment. Peptide aptamers have been shown to be valuable for use as a component of novel, direct detection methods. These small peptides have a number of advantages over antibodies, including greater specificity and longer shelf life. These properties facilitate their use as the detector components of biosensor devices. However, the identification of suitable aptamer targets for particular groups of organisms is challenging. We present a semi-automated processing pipeline for the identification of candidate aptamer targets from whole bacterial genome sequences. The pipeline can be configured to search for protein sequence fragments that uniquely identify a set of strains of interest. The system is also capable of identifying additional organisms that may be of interest due to their possession of protein fragments in common with the initial set. Through the use of Cloud computing technology and distributed databases, our system is capable of scaling with the rapidly growing genome repositories, and consequently of keeping the resulting data sets up-to-date. The system described is also more generically applicable to the discovery of specific targets for other diagnostic approaches such as DNA probes, PCR primers and antibodies.

  16. Screening, Isolation and Identification of Probiotic Producing Lactobacillus acidophilus Strains EMBS081 & EMBS082 by 16S rRNA Gene Sequencing.

    PubMed

    Chandok, Harshpreet; Shah, Pratik; Akare, Uday Raj; Hindala, Maliram; Bhadoriya, Sneha Singh; Ravi, G V; Sharma, Varsha; Bandaru, Srinivas; Rathore, Pragya; Nayarisseri, Anuraj

    2015-09-01

    16S rDNA sequencing which has gained wide popularity amongst microbiologists for the molecular characterization and identification of newly discovered isolates provides accurate identification of isolates down to the level of sub-species (strain). Its most important advantage over the traditional biochemical characterization methods is that it can provide an accurate identification of strains with atypical phenotypic characters as well. The following work is an application of 16S rRNA gene sequencing approach to identify a novel species of Probiotic Lactobacillus acidophilus. The sample was collected from pond water samples of rural and urban areas of Krishna district, Vijayawada, Andhra Pradesh, India. Subsequently, the sample was serially diluted and the aliquots were incubated for a suitable time period following which the suspected colony was subjected to 16S rDNA sequencing. The sequence aligned against other species was concluded to be a novel, Probiotic L. acidophilus bacteria, further which were named L. acidophilus strain EMBS081 & EMBS082. After the sequence characterization, the isolate was deposited in GenBank Database, maintained by the National Centre for Biotechnology Information NCBI. The sequence can also be retrieve from EMBL and DDBJ repositories with accession numbers JX255677 and KC150145.

  17. A distributed computational search strategy for the identification of diagnostics targets: Application to finding aptamer targets for methicillin-resistant staphylococci.

    PubMed

    Flanagan, Keith; Cockell, Simon; Harwood, Colin; Hallinan, Jennifer; Nakjang, Sirintra; Lawry, Beth; Wipat, Anil

    2014-06-01

    The rapid and cost-effective identification of bacterial species is crucial, especially for clinical diagnosis and treatment. Peptide aptamers have been shown to be valuable for use as a component of novel, direct detection methods. These small peptides have a number of advantages over antibodies, including greater specificity and longer shelf life. These properties facilitate their use as the detector components of biosensor devices. However, the identification of suitable aptamer targets for particular groups of organisms is challenging. We present a semi-automated processing pipeline for the identification of candidate aptamer targets from whole bacterial genome sequences. The pipeline can be configured to search for protein sequence fragments that uniquely identify a set of strains of interest. The system is also capable of identifying additional organisms that may be of interest due to their possession of protein fragments in common with the initial set. Through the use of Cloud computing technology and distributed databases, our system is capable of scaling with the rapidly growing genome repositories, and consequently of keeping the resulting data sets up-to-date. The system described is also more generically applicable to the discovery of specific targets for other diagnostic approaches such as DNA probes, PCR primers and antibodies.

  18. Establishment of the first international repository for transfusion-relevant bacteria reference strains: ISBT working party transfusion-transmitted infectious diseases (WP-TTID), subgroup on bacteria.

    PubMed

    Störmer, M; Arroyo, A; Brachert, J; Carrero, H; Devine, D; Epstein, J S; Gabriel, C; Gelber, C; Goodrich, R; Hanschmann, K-M; Heath, D G; Jacobs, M R; Keil, S; de Korte, D; Lambrecht, B; Lee, C-K; Marcelis, J; Marschner, S; McDonald, C; McGuane, S; McKee, M; Müller, T H; Muthivhi, T; Pettersson, A; Radziwon, P; Ramirez-Arcos, S; Reesink, H W; Rojo, J; Rood, I; Schmidt, M; Schneider, C K; Seifried, E; Sicker, U; Wendel, S; Wood, E M; Yomtovian, R A; Montag, T

    2012-01-01

    Bacterial contamination of platelet concentrates (PCs) still remains a significant problem in transfusion with potential important clinical consequences, including death. The International Society of Blood Transfusion Working Party on Transfusion-Transmitted Infectious Diseases, Subgroup on Bacteria, organised an international study on Transfusion-Relevant Bacteria References to be used as a tool for development, validation and comparison of both bacterial screening and pathogen reduction methods. Four Bacteria References (Staphylococcus epidermidis PEI-B-06, Streptococcus pyogenes PEI-B-20, Klebsiella pneumoniae PEI-B-08 and Escherichia coli PEI-B-19) were selected regarding their ability to proliferate to high counts in PCs and distributed anonymised to 14 laboratories in 10 countries for identification, enumeration and bacterial proliferation in PCs after low spiking (0·3 and 0·03 CFU/ml), to simulate contamination occurring during blood donation. Bacteria References were correctly identified in 98% of all 52 identifications. S. pyogenes and E. coli grew in PCs in 11 out of 12 laboratories, and K. pneumoniae and S. epidermidis replicated in all participating laboratories. The results of bacterial counts were very consistent between laboratories: the 95% confidence intervals were for S. epidermidis: 1·19-1·32 × 10(7) CFU/ml, S. pyogenes: 0·58-0·69 × 10(7) CFU/ml, K. pneumoniae: 18·71-20·26 × 10(7) CFU/ml and E. coli: 1·78-2·10 × 10(7) CFU/ml. The study was undertaken as a proof of principle with the aim to demonstrate (i) the quality, stability and suitability of the bacterial strains for low-titre spiking of blood components, (ii) the property of donor-independent proliferation in PCs, and (iii) their suitability for worldwide shipping of deep frozen, blinded pathogenic bacteria. These aims were successfully fulfilled. The WHO Expert Committee Biological Standardisation has approved the adoption of these four bacteria strains as the first Repository for Transfusion-Relevant Bacteria Reference Strains and, additionally, endorsed as a project the addition of six further bacteria strain preparations suitable for control of platelet contamination as the next step of enlargement of the repository. © 2011 The Author(s). Vox Sanguinis © 2011 International Society of Blood Transfusion.

  19. Virtual patient repositories--a comparative analysis.

    PubMed

    Küfner, Julia; Kononowicz, Andrzej A; Hege, Inga

    2014-01-01

    Virtual Patients (VPs) are an important component of medical education. One way to reduce the costs for creating VPs is sharing through repositories. We conducted a literature review to identify existing repositories and analyzed the 17 included repositories in regards to the search functions and metadata they provide. Most repositories provided some metadata such as title or description, whereas other data, such as educational objectives, were less frequent. Future research could, in cooperation with the repository provider, investigate user expectations and usage patterns.

  20. Learning Object Repositories

    ERIC Educational Resources Information Center

    Lehman, Rosemary

    2007-01-01

    This chapter looks at the development and nature of learning objects, meta-tagging standards and taxonomies, learning object repositories, learning object repository characteristics, and types of learning object repositories, with type examples. (Contains 1 table.)

  1. Experiences with Text Mining Large Collections of Unstructured Systems Development Artifacts at JPL

    NASA Technical Reports Server (NTRS)

    Port, Dan; Nikora, Allen; Hihn, Jairus; Huang, LiGuo

    2011-01-01

    Often repositories of systems engineering artifacts at NASA's Jet Propulsion Laboratory (JPL) are so large and poorly structured that they have outgrown our capability to effectively manually process their contents to extract useful information. Sophisticated text mining methods and tools seem a quick, low-effort approach to automating our limited manual efforts. Our experiences of exploring such methods mainly in three areas including historical risk analysis, defect identification based on requirements analysis, and over-time analysis of system anomalies at JPL, have shown that obtaining useful results requires substantial unanticipated efforts - from preprocessing the data to transforming the output for practical applications. We have not observed any quick 'wins' or realized benefit from short-term effort avoidance through automation in this area. Surprisingly we have realized a number of unexpected long-term benefits from the process of applying text mining to our repositories. This paper elaborates some of these benefits and our important lessons learned from the process of preparing and applying text mining to large unstructured system artifacts at JPL aiming to benefit future TM applications in similar problem domains and also in hope for being extended to broader areas of applications.

  2. ProtaBank: A repository for protein design and engineering data.

    PubMed

    Wang, Connie Y; Chang, Paul M; Ary, Marie L; Allen, Benjamin D; Chica, Roberto A; Mayo, Stephen L; Olafson, Barry D

    2018-03-25

    We present ProtaBank, a repository for storing, querying, analyzing, and sharing protein design and engineering data in an actively maintained and updated database. ProtaBank provides a format to describe and compare all types of protein mutational data, spanning a wide range of properties and techniques. It features a user-friendly web interface and programming layer that streamlines data deposition and allows for batch input and queries. The database schema design incorporates a standard format for reporting protein sequences and experimental data that facilitates comparison of results across different data sets. A suite of analysis and visualization tools are provided to facilitate discovery, to guide future designs, and to benchmark and train new predictive tools and algorithms. ProtaBank will provide a valuable resource to the protein engineering community by storing and safeguarding newly generated data, allowing for fast searching and identification of relevant data from the existing literature, and exploring correlations between disparate data sets. ProtaBank invites researchers to contribute data to the database to make it accessible for search and analysis. ProtaBank is available at https://protabank.org. © 2018 The Authors Protein Science published by Wiley Periodicals, Inc. on behalf of The Protein Society.

  3. MASPECTRAS: a platform for management and analysis of proteomics LC-MS/MS data

    PubMed Central

    Hartler, Jürgen; Thallinger, Gerhard G; Stocker, Gernot; Sturn, Alexander; Burkard, Thomas R; Körner, Erik; Rader, Robert; Schmidt, Andreas; Mechtler, Karl; Trajanoski, Zlatko

    2007-01-01

    Background The advancements of proteomics technologies have led to a rapid increase in the number, size and rate at which datasets are generated. Managing and extracting valuable information from such datasets requires the use of data management platforms and computational approaches. Results We have developed the MAss SPECTRometry Analysis System (MASPECTRAS), a platform for management and analysis of proteomics LC-MS/MS data. MASPECTRAS is based on the Proteome Experimental Data Repository (PEDRo) relational database schema and follows the guidelines of the Proteomics Standards Initiative (PSI). Analysis modules include: 1) import and parsing of the results from the search engines SEQUEST, Mascot, Spectrum Mill, X! Tandem, and OMSSA; 2) peptide validation, 3) clustering of proteins based on Markov Clustering and multiple alignments; and 4) quantification using the Automated Statistical Analysis of Protein Abundance Ratios algorithm (ASAPRatio). The system provides customizable data retrieval and visualization tools, as well as export to PRoteomics IDEntifications public repository (PRIDE). MASPECTRAS is freely available at Conclusion Given the unique features and the flexibility due to the use of standard software technology, our platform represents significant advance and could be of great interest to the proteomics community. PMID:17567892

  4. Transportation plan repository and archive.

    DOT National Transportation Integrated Search

    2011-04-01

    This project created a repository and archive for transportation planning documents in Texas within the : established Texas A&M Repository (http://digital.library.tamu.edu). This transportation planning archive : and repository provides ready access ...

  5. Supporting multiple domains in a single reuse repository

    NASA Technical Reports Server (NTRS)

    Eichmann, David A.

    1992-01-01

    Domain analysis typically results in the construction of a domain-specific repository. Such a repository imposes artificial boundaries on the sharing of similar assets between related domains. A lattice-based approach to repository modeling can preserve a reuser's domain specific view of the repository, while avoiding replication of commonly used assets and supporting a more general perspective on domain interrelationships.

  6. NCI Mouse Repository | FNLCR Staging

    Cancer.gov

    The NCI Mouse Repository is an NCI-funded resource for mouse cancer models and associated strains. The repository makes strains available to all members of the scientific community (academic, non-profit, and commercial). NCI Mouse Repository strains

  7. Coupling fuel cycles with repositories: how repository institutional choices may impact fuel cycle design

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Forsberg, C.; Miller, W.F.

    2013-07-01

    The historical repository siting strategy in the United States has been a top-down approach driven by federal government decision making but it has been a failure. This policy has led to dispatching fuel cycle facilities in different states. The U.S. government is now considering an alternative repository siting strategy based on voluntary agreements with state governments. If that occurs, state governments become key decision makers. They have different priorities. Those priorities may change the characteristics of the repository and the fuel cycle. State government priorities, when considering hosting a repository, are safety, financial incentives and jobs. It follows that statesmore » will demand that a repository be the center of the back end of the fuel cycle as a condition of hosting it. For example, states will push for collocation of transportation services, safeguards training, and navy/private SNF (Spent Nuclear Fuel) inspection at the repository site. Such activities would more than double local employment relative to what was planned for the Yucca Mountain-type repository. States may demand (1) the right to take future title of the SNF so if recycle became economic the reprocessing plant would be built at the repository site and (2) the right of a certain fraction of the repository capacity for foreign SNF. That would open the future option of leasing of fuel to foreign utilities with disposal of the SNF in the repository but with the state-government condition that the front-end fuel-cycle enrichment and fuel fabrication facilities be located in that state.« less

  8. NCI Mouse Repository | Frederick National Laboratory for Cancer Research

    Cancer.gov

    The NCI Mouse Repository is an NCI-funded resource for mouse cancer models and associated strains. The repository makes strains available to all members of the scientific community (academic, non-profit, and commercial). NCI Mouse Repository strains

  9. Identification of a selective small molecule inhibitor of breast cancer stem cells.

    PubMed

    Germain, Andrew R; Carmody, Leigh C; Morgan, Barbara; Fernandez, Cristina; Forbeck, Erin; Lewis, Timothy A; Nag, Partha P; Ting, Amal; VerPlank, Lynn; Feng, Yuxiong; Perez, Jose R; Dandapani, Sivaraman; Palmer, Michelle; Lander, Eric S; Gupta, Piyush B; Schreiber, Stuart L; Munoz, Benito

    2012-05-15

    A high-throughput screen (HTS) with the National Institute of Health-Molecular Libraries Small Molecule Repository (NIH-MLSMR) compound collection identified a class of acyl hydrazones to be selectively lethal to breast cancer stem cell (CSC) enriched populations. Medicinal chemistry efforts were undertaken to optimize potency and selectivity of this class of compounds. The optimized compound was declared as a probe (ML239) with the NIH Molecular Libraries Program and displayed greater than 20-fold selective inhibition of the breast CSC-like cell line (HMLE_sh_Ecad) over the isogenic control line (HMLE_sh_GFP). Copyright © 2012 Elsevier Ltd. All rights reserved.

  10. Automatic Target Recognition Based on Cross-Plot

    PubMed Central

    Wong, Kelvin Kian Loong; Abbott, Derek

    2011-01-01

    Automatic target recognition that relies on rapid feature extraction of real-time target from photo-realistic imaging will enable efficient identification of target patterns. To achieve this objective, Cross-plots of binary patterns are explored as potential signatures for the observed target by high-speed capture of the crucial spatial features using minimal computational resources. Target recognition was implemented based on the proposed pattern recognition concept and tested rigorously for its precision and recall performance. We conclude that Cross-plotting is able to produce a digital fingerprint of a target that correlates efficiently and effectively to signatures of patterns having its identity in a target repository. PMID:21980508

  11. Formularity: Software for Automated Formula Assignment of Natural and Other Organic Matter from Ultrahigh-Resolution Mass Spectra

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Tolić, Nikola; Liu, Yina; Liyu, Andrey

    Ultrahigh-resolution mass spectrometry, such as Fourier transform ion-cyclotron resonance mass spectrometry (FT-ICR MS), can resolve thousands of molecular ions in complex organic matrices. A Compound Identification Algorithm (CIA) was previously developed for automated elemental formula assignment for natural organic matter (NOM). In this work we describe a user friendly interface for CIA, titled Formularity, which includes an additional functionality to perform search of formulas based on an Isotopic Pattern Algorithm (IPA). While CIA assigns elemental formulas for compounds containing C, H, O, N, S, and P, IPA is capable of assigning formulas for compounds containing other elements. We used halogenatedmore » organic compounds (HOC), a chemical class that is ubiquitous in nature as well as anthropogenic systems, as an example to demonstrate the capability of Formularity with IPA. A HOC standard mix was used to evaluate the identification confidence of IPA. The HOC spike in NOM and tap water were used to assess HOC identification in natural and anthropogenic matrices. Strategies for reconciliation of CIA and IPA assignments are discussed. Software and sample databases with documentation are freely available from the PNNL OMICS software repository https://omics.pnl.gov/software/formularity.« less

  12. Data repositories for medical education research: issues and recommendations.

    PubMed

    Schwartz, Alan; Pappas, Cleo; Sandlow, Leslie J

    2010-05-01

    The authors explore issues surrounding digital repositories with the twofold intention of clarifying their creation, structure, content, and use, and considering the implementation of a global digital repository for medical education research data sets-an online site where medical education researchers would be encouraged to deposit their data in order to facilitate the reuse and reanalysis of the data by other researchers. By motivating data sharing and reuse, investigators, medical schools, and other stakeholders might see substantial benefits to their own endeavors and to the progress of the field of medical education.The authors review digital repositories in medicine, social sciences, and education, describe the contents and scope of repositories, and present extant examples. The authors describe the potential benefits of a medical education data repository and report results of a survey of the Society for Directors of Research in Medicine Education, in which participants responded to questions about data sharing and a potential data repository. Respondents strongly endorsed data sharing, with the caveat that principal investigators should choose whether or not to share data they collect. A large majority believed that a repository would benefit their unit and the field of medical education. Few reported using existing repositories. Finally, the authors consider challenges to the establishment of such a repository, including taxonomic organization, intellectual property concerns, human subjects protection, technological infrastructure, and evaluation standards. The authors conclude with recommendations for how a medical education data repository could be successfully developed.

  13. 48 CFR 227.7207 - Contractor data repositories.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... repositories. 227.7207 Section 227.7207 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS... Computer Software and Computer Software Documentation 227.7207 Contractor data repositories. Follow 227.7108 when it is in the Government's interests to have a data repository include computer software or to...

  14. 75 FR 70310 - Sunshine Act Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-17

    ... Consumer Protection Act governing the security-based swap data repository registration process, the duties of such repositories, and the core principles applicable to such repositories. 4. The Commission will... security-based swap data repositories or the Commission and the public dissemination of security-based swap...

  15. Core Certification of Data Repositories: Trustworthiness and Long-Term Stewardship

    NASA Astrophysics Data System (ADS)

    de Sherbinin, A. M.; Mokrane, M.; Hugo, W.; Sorvari, S.; Harrison, S.

    2017-12-01

    Scientific integrity and norms dictate that data created and used by scientists should be managed, curated, and archived in trustworthy data repositories thus ensuring that science is verifiable and reproducible while preserving the initial investment in collecting data. Research stakeholders including researchers, science funders, librarians, and publishers must also be able to establish the trustworthiness of data repositories they use to confirm that the data they submit and use remain useful and meaningful in the long term. Data repositories are increasingly recognized as a key element of the global research infrastructure and the importance of establishing their trustworthiness is recognised as a prerequisite for efficient scientific research and data sharing. The Core Trustworthy Data Repository Requirements are a set of universal requirements for certification of data repositories at the core level (see: https://goo.gl/PYsygW). They were developed by the ICSU World Data System (WDS: www.icsu-wds.org) and the Data Seal of Approval (DSA: www.datasealofapproval.org)—the two authoritative organizations responsible for the development and implementation of this standard to be further developed under the CoreTrustSeal branding . CoreTrustSeal certification of data repositories involves a minimally intensive process whereby repositories supply evidence that they are sustainable and trustworthy. Repositories conduct a self-assessment which is then reviewed by community peers. Based on this review CoreTrustSeal certification is granted by the CoreTrustSeal Standards and Certification Board. Certification helps data communities—producers, repositories, and consumers—to improve the quality and transparency of their processes, and to increase awareness of and compliance with established standards. This presentation will introduce the CoreTrustSeal certification requirements for repositories and offer an opportunity to discuss ways to improve the contribution of certified data repositories to sustain open data for open scientific research.

  16. The preliminary design and feasibility study of the spent fuel and high level waste repository in the Czech Republic

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Valvoda, Z.; Holub, J.; Kucerka, M.

    1996-12-31

    In the year 1993, began the Program of Development of the Spent Fuel and High Level Waste Repository in the Conditions of the Czech Republic. During the first phase, the basic concept and structure of the Program has been developed, and the basic design criteria and requirements were prepared. In the conditions of the Czech Republic, only an underground repository in deep geological formation is acceptable. Expected depth is between 500 to 1000 meters and as host rock will be granites. A preliminary variant design study was realized in 1994, that analyzed the radioactive waste and spent fuel flow frommore » NPPs to the repository, various possibilities of transportation in accordance to the various concepts of spent fuel conditioning and transportation to the underground structures. Conditioning and encapsulation of spent fuel and/or radioactive waste is proposed on the repository site. Underground disposal structures are proposed at one underground floor. The repository will have reserve capacity for radioactive waste from NPPs decommissioning and for waste non acceptable to other repositories. Vertical disposal of unshielded canisters in boreholes and/or horizontal disposal of shielded canisters is studied. As the base term of the start up of the repository operation, the year 2035 has been established. From this date, a preliminary time schedule of the Project has been developed. A method of calculating leveled and discounted costs within the repository lifetime, for each of selected 5 variants, was used for economic calculations. Preliminary expected parametric costs of the repository are about 0,1 Kc ($0.004) per MWh, produced in the Czech NPPs. In 1995, the design and feasibility study has gone in more details to the technical concept of repository construction and proposed technologies, as well as to the operational phase of the repository. Paper will describe results of the 1995 design work and will present the program of the repository development in next period.« less

  17. 17 CFR 49.26 - Disclosure requirements of swap data repositories.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... data repository's policies and procedures reasonably designed to protect the privacy of any and all... swap data repositories. 49.26 Section 49.26 Commodity and Securities Exchanges COMMODITY FUTURES TRADING COMMISSION (CONTINUED) SWAP DATA REPOSITORIES § 49.26 Disclosure requirements of swap data...

  18. Making research data repositories visible: the re3data.org Registry.

    PubMed

    Pampel, Heinz; Vierkant, Paul; Scholze, Frank; Bertelmann, Roland; Kindling, Maxi; Klump, Jens; Goebelbecker, Hans-Jürgen; Gundlach, Jens; Schirmbacher, Peter; Dierolf, Uwe

    2013-01-01

    Researchers require infrastructures that ensure a maximum of accessibility, stability and reliability to facilitate working with and sharing of research data. Such infrastructures are being increasingly summarized under the term Research Data Repositories (RDR). The project re3data.org-Registry of Research Data Repositories-has begun to index research data repositories in 2012 and offers researchers, funding organizations, libraries and publishers an overview of the heterogeneous research data repository landscape. In July 2013 re3data.org lists 400 research data repositories and counting. 288 of these are described in detail using the re3data.org vocabulary. Information icons help researchers to easily identify an adequate repository for the storage and reuse of their data. This article describes the heterogeneous RDR landscape and presents a typology of institutional, disciplinary, multidisciplinary and project-specific RDR. Further the article outlines the features of re3data.org, and shows how this registry helps to identify appropriate repositories for storage and search of research data.

  19. NA-42 TI Shared Software Component Library FY2011 Final Report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Knudson, Christa K.; Rutz, Frederick C.; Dorow, Kevin E.

    The NA-42 TI program initiated an effort in FY2010 to standardize its software development efforts with the long term goal of migrating toward a software management approach that will allow for the sharing and reuse of code developed within the TI program, improve integration, ensure a level of software documentation, and reduce development costs. The Pacific Northwest National Laboratory (PNNL) has been tasked with two activities that support this mission. PNNL has been tasked with the identification, selection, and implementation of a Shared Software Component Library. The intent of the library is to provide a common repository that is accessiblemore » by all authorized NA-42 software development teams. The repository facilitates software reuse through a searchable and easy to use web based interface. As software is submitted to the repository, the component registration process captures meta-data and provides version control for compiled libraries, documentation, and source code. This meta-data is then available for retrieval and review as part of library search results. In FY2010, PNNL and staff from the Remote Sensing Laboratory (RSL) teamed up to develop a software application with the goal of replacing the aging Aerial Measuring System (AMS). The application under development includes an Advanced Visualization and Integration of Data (AVID) framework and associated AMS modules. Throughout development, PNNL and RSL have utilized a common AMS code repository for collaborative code development. The AMS repository is hosted by PNNL, is restricted to the project development team, is accessed via two different geographic locations and continues to be used. The knowledge gained from the collaboration and hosting of this repository in conjunction with PNNL software development and systems engineering capabilities were used in the selection of a package to be used in the implementation of the software component library on behalf of NA-42 TI. The second task managed by PNNL is the development and continued maintenance of the NA-42 TI Software Development Questionnaire. This questionnaire is intended to help software development teams working under NA-42 TI in documenting their development activities. When sufficiently completed, the questionnaire illustrates that the software development activities recorded incorporate significant aspects of the software engineering lifecycle. The questionnaire template is updated as comments are received from NA-42 and/or its development teams and revised versions distributed to those using the questionnaire. PNNL also maintains a list of questionnaire recipients. The blank questionnaire template, the AVID and AMS software being developed, and the completed AVID AMS specific questionnaire are being used as the initial content to be established in the TI Component Library. This report summarizes the approach taken to identify requirements, search for and evaluate technologies, and the approach taken for installation of the software needed to host the component library. Additionally, it defines the process by which users request access for the contribution and retrieval of library content.« less

  20. 17 CFR 49.19 - Core principles applicable to registered swap data repositories.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... registered swap data repositories. 49.19 Section 49.19 Commodity and Securities Exchanges COMMODITY FUTURES TRADING COMMISSION (CONTINUED) SWAP DATA REPOSITORIES § 49.19 Core principles applicable to registered swap data repositories. (a) Compliance with core principles. To be registered, and maintain...

  1. 17 CFR 49.26 - Disclosure requirements of swap data repositories.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... TRADING COMMISSION SWAP DATA REPOSITORIES § 49.26 Disclosure requirements of swap data repositories... swap data repository shall furnish to the reporting entity a disclosure document that contains the... 17 Commodity and Securities Exchanges 1 2013-04-01 2013-04-01 false Disclosure requirements of...

  2. 17 CFR 49.26 - Disclosure requirements of swap data repositories.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... TRADING COMMISSION SWAP DATA REPOSITORIES § 49.26 Disclosure requirements of swap data repositories... swap data repository shall furnish to the reporting entity a disclosure document that contains the... 17 Commodity and Securities Exchanges 1 2012-04-01 2012-04-01 false Disclosure requirements of...

  3. 21 CFR 522.480 - Repository corticotropin injection.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Repository corticotropin injection. 522.480 Section 522.480 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... § 522.480 Repository corticotropin injection. (a)(1) Specifications. The drug conforms to repository...

  4. 10 CFR 960.3-1-3 - Regionality.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REPOSITORY Implementation Guidelines § 960.3-1-3 Regionality. In making site recommendations for repository development after the site for the first repository has been recommended, the Secretary shall give due... repositories. Such consideration shall take into account the proximity of sites to locations at which waste is...

  5. Current status and future perspectives on molecular and serological methods in diagnostic mycology.

    PubMed

    Lau, Anna; Chen, Sharon; Sleiman, Sue; Sorrell, Tania

    2009-11-01

    Invasive fungal infections are an important cause of infectious morbidity. Nonculture-based methods are increasingly used for rapid, accurate diagnosis to improve patient outcomes. New and existing DNA amplification platforms have high sensitivity and specificity for direct detection and identification of fungi in clinical specimens. Since laboratories are increasingly reliant on DNA sequencing for fungal identification, measures to improve sequence interpretation should support validation of reference isolates and quality control in public gene repositories. Novel technologies (e.g., isothermal and PNA FISH methods), platforms enabling high-throughput analyses (e.g., DNA microarrays and Luminex xMAP) and/or commercial PCR assays warrant further evaluation for routine diagnostic use. Notwithstanding the advantages of molecular tests, serological assays remain clinically useful for patient management. The serum Aspergillus galactomannan test has been incorporated into diagnostic algorithms of invasive aspergillosis. Both the galactomannan and the serum beta-D-glucan test have value for diagnosing infection and monitoring therapeutic response.

  6. 17 CFR 49.19 - Core principles applicable to registered swap data repositories.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... registered swap data repositories. 49.19 Section 49.19 Commodity and Securities Exchanges COMMODITY FUTURES TRADING COMMISSION SWAP DATA REPOSITORIES § 49.19 Core principles applicable to registered swap data repositories. (a) Compliance with core principles. To be registered, and maintain registration, a swap data...

  7. 17 CFR 49.19 - Core principles applicable to registered swap data repositories.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... registered swap data repositories. 49.19 Section 49.19 Commodity and Securities Exchanges COMMODITY FUTURES TRADING COMMISSION SWAP DATA REPOSITORIES § 49.19 Core principles applicable to registered swap data repositories. (a) Compliance with Core Principles. To be registered, and maintain registration, a swap data...

  8. 17 CFR 49.22 - Chief compliance officer.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... that the registered swap data repository provide fair and open access as set forth in § 49.27 of this...) SWAP DATA REPOSITORIES § 49.22 Chief compliance officer. (a) Definition of Board of Directors. For... data repository, or for those swap data repositories whose organizational structure does not include a...

  9. 75 FR 8701 - Notice of Settlement Agreement Pertaining to Construction of a Waste Repository on the Settlors...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-02-25

    ... Construction of a Waste Repository on the Settlors' Property Pursuant to the Comprehensive Environmental... a Settlement Agreement pertaining to Construction of a Waste Repository on Settlor's Property... waste repository on the property by resolving, liability the settling party might otherwise incur under...

  10. 10 CFR 51.67 - Environmental information concerning geologic repositories.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Environmental information concerning geologic repositories... information concerning geologic repositories. (a) In lieu of an environmental report, the Department of Energy... connection with any geologic repository developed under Subtitle A of Title I, or under Title IV, of the...

  11. 15 CFR 1180.10 - NTIS permanent repository.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 15 Commerce and Foreign Trade 3 2010-01-01 2010-01-01 false NTIS permanent repository. 1180.10... ENGINEERING INFORMATION TO THE NATIONAL TECHNICAL INFORMATION SERVICE § 1180.10 NTIS permanent repository. A... repository as a service to agencies unless the Director advises the Liaison Officer that it has not been so...

  12. 76 FR 14028 - Center for Devices and Radiological Health 510(k) Implementation: Online Repository of Medical...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-15

    ...] Center for Devices and Radiological Health 510(k) Implementation: Online Repository of Medical Device... public meeting entitled ``510(k) Implementation: Discussion of an Online Repository of Medical Device... establish an online public repository of medical device labeling and strategies for displaying device...

  13. Identifying Tensions in the Use of Open Licenses in OER Repositories

    ERIC Educational Resources Information Center

    Amiel, Tel; Soares, Tiago Chagas

    2016-01-01

    We present an analysis of 50 repositories for educational content conducted through an "audit system" that helped us classify these repositories, their software systems, promoters, and how they communicated their licensing practices. We randomly accessed five resources from each repository to investigate the alignment of licensing…

  14. 10 CFR 63.113 - Performance objectives for the geologic repository after permanent closure.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Performance objectives for the geologic repository after...-LEVEL RADIOACTIVE WASTES IN A GEOLOGIC REPOSITORY AT YUCCA MOUNTAIN, NEVADA Technical Criteria Postclosure Performance Objectives § 63.113 Performance objectives for the geologic repository after permanent...

  15. 10 CFR 63.111 - Performance objectives for the geologic repository operations area through permanent closure.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Performance objectives for the geologic repository... (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN A GEOLOGIC REPOSITORY AT YUCCA MOUNTAIN, NEVADA... repository operations area through permanent closure. (a) Protection against radiation exposures and releases...

  16. 10 CFR 960.3-1 - Siting provisions.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REPOSITORY Implementation Guidelines § 960.3-1 Siting provisions. The siting provisions establish the... repositories. As required by the Act, § 960.3-1-3 specifies consideration of a regional distribution of repositories after recommendation of a site for development of the first repository. Section 960.3-1-4...

  17. 10 CFR 60.112 - Overall system performance objective for the geologic repository after permanent closure.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... repository after permanent closure. 60.112 Section 60.112 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN GEOLOGIC REPOSITORIES Technical Criteria Performance Objectives § 60.112 Overall system performance objective for the geologic repository after permanent closure...

  18. 10 CFR 60.132 - Additional design criteria for surface facilities in the geologic repository operations area.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... geologic repository operations area. 60.132 Section 60.132 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN GEOLOGIC REPOSITORIES Technical Criteria Design Criteria for the Geologic Repository Operations Area § 60.132 Additional design criteria for surface facilities in...

  19. 10 CFR 60.111 - Performance of the geologic repository operations area through permanent closure.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Performance of the geologic repository operations area... OF HIGH-LEVEL RADIOACTIVE WASTES IN GEOLOGIC REPOSITORIES Technical Criteria Performance Objectives § 60.111 Performance of the geologic repository operations area through permanent closure. (a...

  20. Institutional Repositories as Infrastructures for Long-Term Preservation

    ERIC Educational Resources Information Center

    Francke, Helena; Gamalielsson, Jonas; Lundell, Björn

    2017-01-01

    Introduction: The study describes the conditions for long-term preservation of the content of the institutional repositories of Swedish higher education institutions based on an investigation of how deposited files are managed with regards to file format and how representatives of the repositories describe the functions of the repositories.…

  1. Data Citation in Neuroimaging: Proposed Best Practices for Data Identification and Attribution

    PubMed Central

    Honor, Leah B.; Haselgrove, Christian; Frazier, Jean A.; Kennedy, David N.

    2016-01-01

    Data sharing and reuse, while widely accepted as good ideas, have been slow to catch on in any concrete and consistent way. One major hurdle within the scientific community has been the lack of widely accepted standards for citing that data, making it difficult to track usage and measure impact. Within the neuroimaging community, there is a need for a way to not only clearly identify and cite datasets, but also to derive new aggregate sets from multiple sources while clearly maintaining lines of attribution. This work presents a functional prototype of a system to integrate Digital Object Identifiers (DOI) and a standardized metadata schema into a XNAT-based repository workflow, allowing for identification of data at both the project and image level. These item and source level identifiers allow any newly defined combination of images, from any number of projects, to be tagged with a new group-level DOI that automatically inherits the individual attributes and provenance information of its constituent parts. This system enables the tracking of data reuse down to the level of individual images. The implementation of this type of data identification system would impact researchers and data creators, data hosting facilities, and data publishers, but the benefit of having widely accepted standards for data identification and attribution would go far toward making data citation practical and advantageous. PMID:27570508

  2. Data Citation in Neuroimaging: Proposed Best Practices for Data Identification and Attribution.

    PubMed

    Honor, Leah B; Haselgrove, Christian; Frazier, Jean A; Kennedy, David N

    2016-01-01

    Data sharing and reuse, while widely accepted as good ideas, have been slow to catch on in any concrete and consistent way. One major hurdle within the scientific community has been the lack of widely accepted standards for citing that data, making it difficult to track usage and measure impact. Within the neuroimaging community, there is a need for a way to not only clearly identify and cite datasets, but also to derive new aggregate sets from multiple sources while clearly maintaining lines of attribution. This work presents a functional prototype of a system to integrate Digital Object Identifiers (DOI) and a standardized metadata schema into a XNAT-based repository workflow, allowing for identification of data at both the project and image level. These item and source level identifiers allow any newly defined combination of images, from any number of projects, to be tagged with a new group-level DOI that automatically inherits the individual attributes and provenance information of its constituent parts. This system enables the tracking of data reuse down to the level of individual images. The implementation of this type of data identification system would impact researchers and data creators, data hosting facilities, and data publishers, but the benefit of having widely accepted standards for data identification and attribution would go far toward making data citation practical and advantageous.

  3. System and method for responding to ground and flight system malfunctions

    NASA Technical Reports Server (NTRS)

    Anderson, Julie J. (Inventor); Fussell, Ronald M. (Inventor)

    2010-01-01

    A system for on-board anomaly resolution for a vehicle has a data repository. The data repository stores data related to different systems, subsystems, and components of the vehicle. The data stored is encoded in a tree-based structure. A query engine is coupled to the data repository. The query engine provides a user and automated interface and provides contextual query to the data repository. An inference engine is coupled to the query engine. The inference engine compares current anomaly data to contextual data stored in the data repository using inference rules. The inference engine generates a potential solution to the current anomaly by referencing the data stored in the data repository.

  4. 17 CFR 49.9 - Duties of registered swap data repositories.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... privacy of any and all swap data and any other related information that the swap data repository receives... 17 Commodity and Securities Exchanges 2 2014-04-01 2014-04-01 false Duties of registered swap data... (CONTINUED) SWAP DATA REPOSITORIES § 49.9 Duties of registered swap data repositories. (a) Duties. To be...

  5. Availability and Accessibility in an Open Access Institutional Repository: A Case Study

    ERIC Educational Resources Information Center

    Lee, Jongwook; Burnett, Gary; Vandegrift, Micah; Baeg, Jung Hoon; Morris, Richard

    2015-01-01

    Introduction: This study explores the extent to which an institutional repository makes papers available and accessible on the open Web by using 170 journal articles housed in DigiNole Commons, the institutional repository at Florida State University. Method: To analyse the repository's impact on availability and accessibility, we conducted…

  6. The Use of Digital Repositories for Enhancing Teacher Pedagogical Performance

    ERIC Educational Resources Information Center

    Cohen, Anat; Kalimi, Sharon; Nachmias, Rafi

    2013-01-01

    This research examines the usage of local learning material repositories at school, as well as related teachers' attitudes and training. The study investigates the use of these repositories for enhancing teacher performance and assesses whether the assimilation of the local repositories increases their usage of and contribution to by teachers. One…

  7. Institutional Repositories in Indian Universities and Research Institutes: A Study

    ERIC Educational Resources Information Center

    Krishnamurthy, M.; Kemparaju, T. D.

    2011-01-01

    Purpose: The purpose of this paper is to report on a study of the institutional repositories (IRs) in use in Indian universities and research institutes. Design/methodology/approach: Repositories in various institutions in India were accessed and described in a standardised way. Findings: The 20 repositories studied covered collections of diverse…

  8. 10 CFR 63.161 - Emergency plan for the geologic repository operations area through permanent closure.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Emergency plan for the geologic repository operations area... OF HIGH-LEVEL RADIOACTIVE WASTES IN A GEOLOGIC REPOSITORY AT YUCCA MOUNTAIN, NEVADA Emergency Planning Criteria § 63.161 Emergency plan for the geologic repository operations area through permanent...

  9. 77 FR 26709 - Swap Data Repositories: Interpretative Statement Regarding the Confidentiality and...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-05-07

    ... COMMODITY FUTURES TRADING COMMISSION 17 CFR Part 49 RIN 3038-AD83 Swap Data Repositories... data repositories (``SDRs'').SDRs are new registered entities created by section 728 of the Dodd-Frank... Act amends section 1a of the CEA to add a definition of the term ``swap data repository.'' Pursuant to...

  10. Online Paper Repositories and the Role of Scholarly Societies: An AERA Conference Report

    ERIC Educational Resources Information Center

    Educational Researcher, 2010

    2010-01-01

    This article examines issues faced by scholarly societies that are developing and sustaining online paper repositories. It is based on the AERA Conference on Online Paper Repositories, which focused on fundamental issues of policy and procedure important to the operations of online working paper repositories. The report and recommendations address…

  11. 10 CFR 960.3-2-2 - Nomination of sites as suitable for characterization.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... OF POTENTIAL SITES FOR A NUCLEAR WASTE REPOSITORY Implementation Guidelines § 960.3-2-2 Nomination of... of each repository site. For the second repository, at least three of the sites shall not have been nominated previously. Any site nominated as suitable for characterization for the first repository, but not...

  12. Repositories for Research: Southampton's Evolving Role in the Knowledge Cycle

    ERIC Educational Resources Information Center

    Simpson, Pauline; Hey, Jessie

    2006-01-01

    Purpose: To provide an overview of how open access (OA) repositories have grown to take a premier place in the e-research knowledge cycle and offer Southampton's route from project to sustainable institutional repository. Design/methodology/approach: The evolution of institutional repositories and OA is outlined raising questions of multiplicity…

  13. Interoperability Across the Stewardship Spectrum in the DataONE Repository Federation

    NASA Astrophysics Data System (ADS)

    Jones, M. B.; Vieglais, D.; Wilson, B. E.

    2016-12-01

    Thousands of earth and environmental science repositories serve many researchers and communities, each with their own community and legal mandates, sustainability models, and historical infrastructure. These repositories span the stewardship spectrum from highly curated collections that employ large numbers of staff members to review and improve data, to small, minimal budget repositories that accept data caveat emptor and where all responsibility for quality lies with the submitter. Each repository fills a niche, providing services that meet the stewardship tradeoffs of one or more communities. We have reviewed these stewardship tradeoffs for several DataONE member repositories ranging from minimally (KNB) to highly curated (Arctic Data Center), as well as general purpose (Dryad) to highly discipline or project specific (NEON). The rationale behind different levels of stewardship reflect resolution of these tradeoffs. Some repositories aim to encourage extensive uptake by keeping processes simple and minimizing the amount of information collected, but this limits the long-term utility of the data and the search, discovery, and integration systems that are possible. Other repositories require extensive metadata input, review, and assessment, allowing for excellent preservation, discovery, and integration but at the cost of significant time for submitters and expense for curatorial staff. DataONE recognizes these different levels of curation, and attempts to embrace them to create a federation that is useful across the stewardship spectrum. DataONE provides a tiered model for repositories with growing utility of DataONE services at higher tiers of curation. The lowest tier supports read-only access to data and requires little more than title and contact metadata. Repositories can gradually phase in support for higher levels of metadata and services as needed. These tiered capabilities are possible through flexible support for multiple metadata standards and services, where repositories can incrementally increase their requirements as they want to satisfy more use cases. Within DataONE, metadata search services support minimal metadata models, but significantly expanded precision and recall become possible when repositories provide more extensively curated metadata.

  14. Optimizing Resources for Trustworthiness and Scientific Impact of Domain Repositories

    NASA Astrophysics Data System (ADS)

    Lehnert, K.

    2017-12-01

    Domain repositories, i.e. data archives tied to specific scientific communities, are widely recognized and trusted by their user communities for ensuring a high level of data quality, enhancing data value, access, and reuse through a unique combination of disciplinary and digital curation expertise. Their data services are guided by the practices and values of the specific community they serve and designed to support the advancement of their science. Domain repositories need to meet user expectations for scientific utility in order to be successful, but they also need to fulfill the requirements for trustworthy repository services to be acknowledged by scientists, funders, and publishers as a reliable facility that curates and preserves data following international standards. Domain repositories therefore need to carefully plan and balance investments to optimize the scientific impact of their data services and user satisfaction on the one hand, while maintaining a reliable and robust operation of the repository infrastructure on the other hand. Staying abreast of evolving repository standards to certify as a trustworthy repository and conducting a regular self-assessment and certification alone requires resources that compete with the demands for improving data holdings or usability of systems. The Interdisciplinary Earth Data Alliance (IEDA), a data facility funded by the US National Science Foundation, operates repositories for geochemical, marine Geoscience, and Antarctic research data, while also maintaining data products (global syntheses) and data visualization and analysis tools that are of high value for the science community and have demonstrated considerable scientific impact. Balancing the investments in the growth and utility of the syntheses with resources required for certifcation of IEDA's repository services has been challenging, and a major self-assessment effort has been difficult to accommodate. IEDA is exploring a partnership model to share generic repository functions (e.g. metadata registration, long-term archiving) with other repositories. This could substantially reduce the effort of certification and allow effort to focus on the domain-specific data curation and value-added services.

  15. Building Scientific Data's list of recommended data repositories

    NASA Astrophysics Data System (ADS)

    Hufton, A. L.; Khodiyar, V.; Hrynaszkiewicz, I.

    2016-12-01

    When Scientific Data launched in 2014 we provided our authors with a list of recommended data repositories to help them identify data hosting options that were likely to meet the journal's requirements. This list has grown in size and scope, and is now a central resource for authors across the Nature-titled journals. It has also been used in the development of data deposition policies and recommended repository lists across Springer Nature and at other publishers. Each new addition to the list is assessed according to a series of criteria that emphasize the stability of the resource, its commitment to principles of open science and its implementation of relevant community standards and reporting guidelines. A preference is expressed for repositories that issue digital object identifiers (DOIs) through the DataCite system and that share data under the Creative Commons CC0 waiver. Scientific Data currently lists fourteen repositories that focus on specific areas within the Earth and environmental sciences, as well as the broad scope repositories, Dryad and figshare. Readers can browse and filter datasets published at the journal by the host repository using ISA-explorer, a demo tool built by the ISA-tools team at Oxford University1. We believe that well-maintained lists like this one help publishers build a network of trust with community data repositories and provide an important complement to more comprehensive data repository indices and more formal certification efforts. In parallel, Scientific Data has also improved its policies to better support submissions from authors using institutional and project-specific repositories, without requiring each to apply for listing individually. Online resources Journal homepage: http://www.nature.com/scientificdata Data repository criteria: http://www.nature.com/sdata/policies/data-policies#repo-criteria Recommended data repositories: http://www.nature.com/sdata/policies/repositories Archived copies of the list: https://dx.doi.org/10.6084/m9.figshare.1434640.v6 Reference Gonzalez-Beltran, A. ISA-explorer: A demo tool for discovering and exploring Scientific Data's ISA-tab metadata. Scientific Data Updates http://blogs.nature.com/scientificdata/2015/12/17/isa-explorer/ (2015).

  16. Commodity Flow Study - Clark County, Nevada, USA

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Conway, S.Ph.D.; Navis, I.

    2008-07-01

    The United States Department of Energy has designated Clark County, Nevada as an 'Affected Unit of Local Government' due to the potential for impacts by activities associated with the Yucca Mountain High Level Nuclear Waste Repository project. Urban Transit, LLC has led a project team of transportation including experts from the University of Nevada Las Vegas Transportation Research Center to conduct a hazardous materials community flow study along Clark County's rail and truck corridors. In addition, a critical infrastructure analysis has also been carried out in order to assess the potential impacts of transportation within Clark County of high levelmore » nuclear waste and spent nuclear fuel to a proposed repository 90 miles away in an adjacent county on the critical infrastructure in Clark County. These studies were designed to obtain information relating to the transportation, identification and routing of hazardous materials through Clark County. Coordinating with the United States Department of Energy, the U.S. Department of Agriculture, the U. S. Federal Highway Administration, the Nevada Department of Transportation, and various other stakeholders, these studies and future research will examine the risk factors along the entire transportation corridor within Clark County and provide a context for understanding the additional vulnerability associated with shipping spent fuel through Clark County. (authors)« less

  17. Attribute Weighting Based K-Nearest Neighbor Using Gain Ratio

    NASA Astrophysics Data System (ADS)

    Nababan, A. A.; Sitompul, O. S.; Tulus

    2018-04-01

    K- Nearest Neighbor (KNN) is a good classifier, but from several studies, the result performance accuracy of KNN still lower than other methods. One of the causes of the low accuracy produced, because each attribute has the same effect on the classification process, while some less relevant characteristics lead to miss-classification of the class assignment for new data. In this research, we proposed Attribute Weighting Based K-Nearest Neighbor Using Gain Ratio as a parameter to see the correlation between each attribute in the data and the Gain Ratio also will be used as the basis for weighting each attribute of the dataset. The accuracy of results is compared to the accuracy acquired from the original KNN method using 10-fold Cross-Validation with several datasets from the UCI Machine Learning repository and KEEL-Dataset Repository, such as abalone, glass identification, haberman, hayes-roth and water quality status. Based on the result of the test, the proposed method was able to increase the classification accuracy of KNN, where the highest difference of accuracy obtained hayes-roth dataset is worth 12.73%, and the lowest difference of accuracy obtained in the abalone dataset of 0.07%. The average result of the accuracy of all dataset increases the accuracy by 5.33%.

  18. The Emperor's New Repository

    ERIC Educational Resources Information Center

    Chudnov, Daniel

    2008-01-01

    The author does not know the first thing about building digital repositories. Maybe that is a strange thing to say, given that he works in a repository development group now, worked on the original DSpace project years ago, and worked on a few repository research projects in between. Given how long he has been around people and projects aiming to…

  19. Genetic conservation, characterization and utilization of wild relatives of fruit and nut crops at the USDA Germplasm Repository in Davis, California

    USDA-ARS?s Scientific Manuscript database

    The National Clonal Germplasm Repository (NCGR) in Davis is one among the nine repositories in the National Plant Germplasm System, USDA-ARS that is responsible for conservation of clonally propagated woody perennial subtropical and temperate fruit and nut crop germplasm. Currently the repository ho...

  20. 36 CFR 79.9 - Standards to determine when a repository possesses the capability to provide adequate long-term...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... repository possesses the capability to provide adequate long-term curatorial services. 79.9 Section 79.9... FEDERALLY-OWNED AND ADMINISTERED ARCHAEOLOGICAL COLLECTIONS § 79.9 Standards to determine when a repository... shall determine that a repository has the capability to provide adequate long-term curatorial services...

  1. 10 CFR Appendix II to Part 960 - NRC and EPA Requirements for Preclosure Repository Performance

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false NRC and EPA Requirements for Preclosure Repository... SCREENING OF POTENTIAL SITES FOR A NUCLEAR WASTE REPOSITORY Pt. 960, App. II Appendix II to Part 960—NRC and EPA Requirements for Preclosure Repository Performance Under proposed 40 CFR part 191, subpart A...

  2. 10 CFR 51.109 - Public hearings in proceedings for issuance of materials license with respect to a geologic...

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... license with respect to a geologic repository. 51.109 Section 51.109 Energy NUCLEAR REGULATORY COMMISSION... Public hearings in proceedings for issuance of materials license with respect to a geologic repository... waste repository at a geologic repository operations area under parts 60 and 63 of this chapter, and in...

  3. Semantic Linking of Learning Object Repositories to DBpedia

    ERIC Educational Resources Information Center

    Lama, Manuel; Vidal, Juan C.; Otero-Garcia, Estefania; Bugarin, Alberto; Barro, Senen

    2012-01-01

    Large-sized repositories of learning objects (LOs) are difficult to create and also to maintain. In this paper we propose a way to reduce this drawback by improving the classification mechanisms of the LO repositories. Specifically, we present a solution to automate the LO classification of the Universia repository, a collection of more than 15…

  4. 10 CFR Appendix I to Part 960 - NRC and EPA Requirements for Postclosure Repository Performance

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false NRC and EPA Requirements for Postclosure Repository... SCREENING OF POTENTIAL SITES FOR A NUCLEAR WASTE REPOSITORY Pt. 960, App. I Appendix I to Part 960—NRC and EPA Requirements for Postclosure Repository Performance Under proposed 40 CFR part 191, subpart B...

  5. Desiderata for Healthcare Integrated Data Repositories Based on Architectural Comparison of Three Public Repositories

    PubMed Central

    Huser, Vojtech; Cimino, James J.

    2013-01-01

    Integrated data repositories (IDRs) are indispensable tools for numerous biomedical research studies. We compare three large IDRs (Informatics for Integrating Biology and the Bedside (i2b2), HMO Research Network’s Virtual Data Warehouse (VDW) and Observational Medical Outcomes Partnership (OMOP) repository) in order to identify common architectural features that enable efficient storage and organization of large amounts of clinical data. We define three high-level classes of underlying data storage models and we analyze each repository using this classification. We look at how a set of sample facts is represented in each repository and conclude with a list of desiderata for IDRs that deal with the information storage model, terminology model, data integration and value-sets management. PMID:24551366

  6. Desiderata for healthcare integrated data repositories based on architectural comparison of three public repositories.

    PubMed

    Huser, Vojtech; Cimino, James J

    2013-01-01

    Integrated data repositories (IDRs) are indispensable tools for numerous biomedical research studies. We compare three large IDRs (Informatics for Integrating Biology and the Bedside (i2b2), HMO Research Network's Virtual Data Warehouse (VDW) and Observational Medical Outcomes Partnership (OMOP) repository) in order to identify common architectural features that enable efficient storage and organization of large amounts of clinical data. We define three high-level classes of underlying data storage models and we analyze each repository using this classification. We look at how a set of sample facts is represented in each repository and conclude with a list of desiderata for IDRs that deal with the information storage model, terminology model, data integration and value-sets management.

  7. 75 FR 26788 - Public Land Order No. 7742; Withdrawal of Public Land for the Manning Canyon Tailings Repository; UT

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-12

    ... 79765] Public Land Order No. 7742; Withdrawal of Public Land for the Manning Canyon Tailings Repository... period of 5 years to protect the integrity of the Manning Canyon Tailings Repository and surrounding... Repository. The Bureau of Land Management intends to evaluate the need for a lengthier withdrawal through the...

  8. The Research Library's Role in Digital Repository Services: Final Report of the ARL Digital Repository Issues Task Force

    ERIC Educational Resources Information Center

    Association of Research Libraries, 2009

    2009-01-01

    Libraries are making diverse contributions to the development of many types of digital repositories, particularly those housing locally created digital content, including new digital objects or digitized versions of locally held works. In some instances, libraries are managing a repository and its related services entirely on their own, but often…

  9. Analysis of Academic Attitudes and Existing Processes to Inform the Design of Teaching and Learning Material Repositories: A User-Centred Approach

    ERIC Educational Resources Information Center

    King, Melanie; Loddington, Steve; Manuel, Sue; Oppenheim, Charles

    2008-01-01

    The last couple of years have brought a rise in the number of institutional repositories throughout the world and within UK Higher Education institutions, with the majority of these repositories being devoted to research output. Repositories containing teaching and learning material are less common and the workflows and business processes…

  10. Integrating XQuery-Enabled SCORM XML Metadata Repositories into an RDF-Based E-Learning P2P Network

    ERIC Educational Resources Information Center

    Qu, Changtao; Nejdl, Wolfgang

    2004-01-01

    Edutella is an RDF-based E-Learning P2P network that is aimed to accommodate heterogeneous learning resource metadata repositories in a P2P manner and further facilitate the exchange of metadata between these repositories based on RDF. Whereas Edutella provides RDF metadata repositories with a quite natural integration approach, XML metadata…

  11. Scaling an expert system data mart: more facilities in real-time.

    PubMed

    McNamee, L A; Launsby, B D; Frisse, M E; Lehmann, R; Ebker, K

    1998-01-01

    Clinical Data Repositories are being rapidly adopted by large healthcare organizations as a method of centralizing and unifying clinical data currently stored in diverse and isolated information systems. Once stored in a clinical data repository, healthcare organizations seek to use this centralized data to store, analyze, interpret, and influence clinical care, quality and outcomes. A recent trend in the repository field has been the adoption of data marts--specialized subsets of enterprise-wide data taken from a larger repository designed specifically to answer highly focused questions. A data mart exploits the data stored in the repository, but can use unique structures or summary statistics generated specifically for an area of study. Thus, data marts benefit from the existence of a repository, are less general than a repository, but provide more effective and efficient support for an enterprise-wide data analysis task. In previous work, we described the use of batch processing for populating data marts directly from legacy systems. In this paper, we describe an architecture that uses both primary data sources and an evolving enterprise-wide clinical data repository to create real-time data sources for a clinical data mart to support highly specialized clinical expert systems.

  12. Schematic designs for penetration seals for a reference repository in bedded salt

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Kelsall, P.C.; Case, J.B.; Meyer, D.

    1982-11-01

    The isolation of radioactive wastes in geologic repositories requires that man-made penetrations such as shafts, tunnels, or boreholes are adequately sealed. This report describes schematic seal designs for a repository in bedded salt referenced to the straitigraphy of southeastern New Mexico. The designs are presented for extensive peer review and will be updated as site-specific conceptual designs when a site for a repository in salt has been selected. The principal material used in the seal system is crushed salt obtained from excavating the repository. It is anticipated that crushed salt will consolidate as the repository rooms creep close to themore » degree that mechanical and hydrologic properties will eventually match those of undisturbed, intact salt. For southeastern New Mexico salt, analyses indicate that this process will require approximately 1000 years for a seal located at the base of one of the repository shafts (where there is little increase in temperature due to waste emplacement) and approximately 400 years for a seal located in an access tunnel within the repository. Bulkheads composed of contrete or salt bricks are also included in the seal system as components which will have low permeability during the period required for salt consolidation.« less

  13. Making Research Data Repositories Visible: The re3data.org Registry

    PubMed Central

    Pampel, Heinz; Vierkant, Paul; Scholze, Frank; Bertelmann, Roland; Kindling, Maxi; Klump, Jens; Goebelbecker, Hans-Jürgen; Gundlach, Jens; Schirmbacher, Peter; Dierolf, Uwe

    2013-01-01

    Researchers require infrastructures that ensure a maximum of accessibility, stability and reliability to facilitate working with and sharing of research data. Such infrastructures are being increasingly summarized under the term Research Data Repositories (RDR). The project re3data.org–Registry of Research Data Repositories–has begun to index research data repositories in 2012 and offers researchers, funding organizations, libraries and publishers an overview of the heterogeneous research data repository landscape. In July 2013 re3data.org lists 400 research data repositories and counting. 288 of these are described in detail using the re3data.org vocabulary. Information icons help researchers to easily identify an adequate repository for the storage and reuse of their data. This article describes the heterogeneous RDR landscape and presents a typology of institutional, disciplinary, multidisciplinary and project-specific RDR. Further the article outlines the features of re3data.org, and shows how this registry helps to identify appropriate repositories for storage and search of research data. PMID:24223762

  14. AdaNET phase 0 support for the AdaNET Dynamic Software Inventory (DSI) management system prototype. Catalog of available reusable software components

    NASA Technical Reports Server (NTRS)

    Hanley, Lionel

    1989-01-01

    The Ada Software Repository is a public-domain collection of Ada software and information. The Ada Software Repository is one of several repositories located on the SIMTEL20 Defense Data Network host computer at White Sands Missile Range, and available to any host computer on the network since 26 November 1984. This repository provides a free source for Ada programs and information. The Ada Software Repository is divided into several subdirectories. These directories are organized by topic, and their names and a brief overview of their topics are contained. The Ada Software Repository on SIMTEL20 serves two basic roles: to promote the exchange and use (reusability) of Ada programs and tools (including components) and to promote Ada education.

  15. Exploring Characterizations of Learning Object Repositories Using Data Mining Techniques

    NASA Astrophysics Data System (ADS)

    Segura, Alejandra; Vidal, Christian; Menendez, Victor; Zapata, Alfredo; Prieto, Manuel

    Learning object repositories provide a platform for the sharing of Web-based educational resources. As these repositories evolve independently, it is difficult for users to have a clear picture of the kind of contents they give access to. Metadata can be used to automatically extract a characterization of these resources by using machine learning techniques. This paper presents an exploratory study carried out in the contents of four public repositories that uses clustering and association rule mining algorithms to extract characterizations of repository contents. The results of the analysis include potential relationships between different attributes of learning objects that may be useful to gain an understanding of the kind of resources available and eventually develop search mechanisms that consider repository descriptions as a criteria in federated search.

  16. Geosamples.org: Shared Cyberinfrastructure for Geoscience Samples

    NASA Astrophysics Data System (ADS)

    Lehnert, Kerstin; Allison, Lee; Arctur, David; Klump, Jens; Lenhardt, Christopher

    2014-05-01

    Many scientific domains, specifically in the geosciences, rely on physical samples as basic elements for study and experimentation. Samples are collected to analyze properties of natural materials and features that are key to our knowledge of Earth's dynamical systems and evolution, and to preserve a record of our environment over time. Huge volumes of samples have been acquired over decades or even centuries and stored in a large number and variety of institutions including museums, universities and colleges, state geological surveys, federal agencies, and industry. All of these collections represent highly valuable, often irreplaceable records of nature that need to be accessible so that they can be re-used in future research and for educational purposes. Many sample repositories are keen to use cyberinfrastructure capabilities to enhance access to their collections on the internet and to support and streamline collection management (accessioning of new samples, labeling, handling sample requests, etc.), but encounter substantial challenges and barriers to integrate digital sample management into their daily routine. They lack the resources (staff, funding) and infrastructure (hardware, software, IT support) to develop and operate web-enabled databases, to migrate analog sample records into digital data management systems, and to transfer paper- or spreadsheet-based workflows to electronic systems. Use of commercial software is often not an option as it incurs high costs for licenses, requires IT expertise for installation and maintenance, and often does not match the needs of the smaller repositories, being designed for large museums or different types of collections (art, archeological, biological). Geosamples.org is an alliance of sample repositories (academic, US federal and state surveys, industry) and data facilities that aims to develop a cyberinfrastructure that will dramatically advance access to physical samples for the research community, government agencies, students, educators, and the general public, while supporting, simplifying, and standardizing the work of curators in repositories, museums, and universities, and even for individual investigators who manage personal or project-based sample collections in their lab. Geosamples.org builds upon best practices and cyberinfrastructure for sample identification, registration, and documentation developed by the IGSN e.V., an international organization that governs the International Geosample Number, a persistent unique identifier for physical samples. Geosamples.org will develop a Digital Environment for Sample Curation (DESC) that will facilitate the creation, identification, and registration of 'virtual samples' and network them into an 'Internet of Samples' that will allow to discover, access, and track online physical samples, the data derived by their study, and the publications that contain these data. DESC will provide easy-to-use software tools for curators to maintain digital catalogs of their collections, to provide online access to the catalog to search for and request samples, manage sample requests and users, track collection usage and impact. Geosamples.org will also work toward joint practices for the recognition of intellectual property, build mechanisms to create sustainable business models for continuing maintenance and evolution of managing sample resources, and integrate the sample management life-cycle into professional and cultural practice of science.

  17. Results of instrument reliability study for high-level nuclear-waste repositories. [Geotechnical parameters

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Rogue, F.; Binnall, E.P.

    1982-10-01

    Reliable instrumentation will be needed to monitor the performance of future high-level waste repository sites. A study has been made to assess instrument reliability at Department of Energy (DOE) waste repository related experiments. Though the study covers a wide variety of instrumentation, this paper concentrates on experiences with geotechnical instrumentation in hostile repository-type environments. Manufacturers have made some changes to improve the reliability of instruments for repositories. This paper reviews the failure modes, rates, and mechanisms, along with manufacturer modifications and recommendations for additional improvements to enhance instrument performance. 4 tables.

  18. Coupled Biological-Geomechanical-Geochemical Effects of the Disturbed Rock Zone on the Performance of the Waste Isolation Pilot Plant

    NASA Astrophysics Data System (ADS)

    Dunagan, S. C.; Herrick, C. G.; Lee, M. Y.

    2008-12-01

    The Waste Isolation Pilot Plant (WIPP) is located at a depth of 655 m in bedded salt in southeastern New Mexico and is operated by the U.S. Department of Energy as a deep underground disposal facility for transuranic (TRU) waste. The WIPP must comply with the EPA's environmental regulations that require a probabilistic risk analysis of releases of radionuclides due to inadvertent human intrusion into the repository at some time during the 10,000-year regulatory period. Sandia National Laboratories conducts performance assessments (PAs) of the WIPP using a system of computer codes representing the evolution of underground repository and emplaced TRU waste in order to demonstrate compliance. One of the important features modeled in a PA is the disturbed rock zone (DRZ) surrounding the emplacement rooms in the repository. The extent and permeability of DRZ play a significant role in the potential radionuclide release scenarios. We evaluated the phenomena occurring in the repository that affect the DRZ and their potential effects on the extent and permeability of the DRZ. Furthermore, we examined the DRZ's role in determining the performance of the repository. Pressure in the completely sealed repository will be increased by creep closure of the salt and degradation of TRU waste contents by microbial activity in the repository. An increased pressure in the repository will reduce the extent and permeability of the DRZ. The reduced DRZ extent and permeability will decrease the amount of brine that is available to interact with the waste. Furthermore, the potential for radionuclide release from the repository is dependent on the amount of brine that enters the repository. As a result of these coupled biological-geomechanical-geochemical phenomena, the extent and permeability of the DRZ has a significant impact on the potential radionuclide releases from the repository and, in turn, the repository performance. Sandia is a multi program laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the United States Department of Energy's National Nuclear Security Administration under Contract DE-AC04- 94AL85000. This research is funded by WIPP programs administered by the Office of Environmental Management (EM) of the U.S. Department of Energy.

  19. Corticotropin, Repository Injection

    MedlinePlus

    Corticotropin repository injection is used to treat the following conditions:infantile spasms (seizures that usually begin during the first ... of the arms, hands, feet, and legs). Corticotropin repository injection is in a class of medications called ...

  20. 10 CFR 60.134 - Design of seals for shafts and boreholes.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... GEOLOGIC REPOSITORIES Technical Criteria Design Criteria for the Geologic Repository Operations Area § 60... the geologic repository's ability to meet the performance objectives or the period following permanent...

  1. MetMSLine: an automated and fully integrated pipeline for rapid processing of high-resolution LC-MS metabolomic datasets.

    PubMed

    Edmands, William M B; Barupal, Dinesh K; Scalbert, Augustin

    2015-03-01

    MetMSLine represents a complete collection of functions in the R programming language as an accessible GUI for biomarker discovery in large-scale liquid-chromatography high-resolution mass spectral datasets from acquisition through to final metabolite identification forming a backend to output from any peak-picking software such as XCMS. MetMSLine automatically creates subdirectories, data tables and relevant figures at the following steps: (i) signal smoothing, normalization, filtration and noise transformation (PreProc.QC.LSC.R); (ii) PCA and automatic outlier removal (Auto.PCA.R); (iii) automatic regression, biomarker selection, hierarchical clustering and cluster ion/artefact identification (Auto.MV.Regress.R); (iv) Biomarker-MS/MS fragmentation spectra matching and fragment/neutral loss annotation (Auto.MS.MS.match.R) and (v) semi-targeted metabolite identification based on a list of theoretical masses obtained from public databases (DBAnnotate.R). All source code and suggested parameters are available in an un-encapsulated layout on http://wmbedmands.github.io/MetMSLine/. Readme files and a synthetic dataset of both X-variables (simulated LC-MS data), Y-variables (simulated continuous variables) and metabolite theoretical masses are also available on our GitHub repository. © The Author 2014. Published by Oxford University Press.

  2. MetMSLine: an automated and fully integrated pipeline for rapid processing of high-resolution LC–MS metabolomic datasets

    PubMed Central

    Edmands, William M. B.; Barupal, Dinesh K.; Scalbert, Augustin

    2015-01-01

    Summary: MetMSLine represents a complete collection of functions in the R programming language as an accessible GUI for biomarker discovery in large-scale liquid-chromatography high-resolution mass spectral datasets from acquisition through to final metabolite identification forming a backend to output from any peak-picking software such as XCMS. MetMSLine automatically creates subdirectories, data tables and relevant figures at the following steps: (i) signal smoothing, normalization, filtration and noise transformation (PreProc.QC.LSC.R); (ii) PCA and automatic outlier removal (Auto.PCA.R); (iii) automatic regression, biomarker selection, hierarchical clustering and cluster ion/artefact identification (Auto.MV.Regress.R); (iv) Biomarker—MS/MS fragmentation spectra matching and fragment/neutral loss annotation (Auto.MS.MS.match.R) and (v) semi-targeted metabolite identification based on a list of theoretical masses obtained from public databases (DBAnnotate.R). Availability and implementation: All source code and suggested parameters are available in an un-encapsulated layout on http://wmbedmands.github.io/MetMSLine/. Readme files and a synthetic dataset of both X-variables (simulated LC–MS data), Y-variables (simulated continuous variables) and metabolite theoretical masses are also available on our GitHub repository. Contact: ScalbertA@iarc.fr PMID:25348215

  3. 10 CFR 960.5-2 - Technical guidelines.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REPOSITORY Preclosure Guidelines § 960.5-2 Technical guidelines. The technical guidelines in this subpart set... repository and to the transportation of waste to a repository site. The third group includes conditions on...

  4. Assessing repository technology. Where do we go from here?

    NASA Technical Reports Server (NTRS)

    Eichmann, David

    1992-01-01

    Three sample information retrieval systems, archie, autoLib, and Wide Area Information Service (WAIS), are compared with regard to their expressiveness and usefulness, first in the general context of information retrieval, and then as prospective software reuse repositories. While the representational capabilities of these systems are limited, they provide a useful foundation for future repository efforts, particularly from the perspective of repository distribution and coherent user interface design.

  5. Assessing repository technology: Where do we go from here?

    NASA Technical Reports Server (NTRS)

    Eichmann, David A.

    1992-01-01

    Three sample information retrieval systems, archie, autoLib, and Wide Area Information Service (WAIS), are compared with regard to their expressiveness and usefulness, first in the general context of information retrieval, and then as perspective software reuse repositories. While the representational capabilities of these systems are limited, they provide a useful foundation for future repository efforts, particularly from the perspective of repository distribution and coherent user interface design.

  6. USAF Hearing Conservation Program, DOEHRS-HC Data Repository Annual Report: CY15

    DTIC Science & Technology

    2017-05-31

    AFRL-SA-WP-SR-2017-0014 USAF Hearing Conservation Program, DOEHRS-HC Data Repository Annual Report: CY15 Daniel A. Williams...Conservation Program, DOEHRS-HC Data Repository Annual Report: CY15 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR...Health Readiness System-Hearing Conservation Data Repository (DOEHRS-HC DR). Major command- and installation-level reports are available quarterly

  7. 10 CFR 960.3-4 - Environmental impacts.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REPOSITORY Implementation Guidelines § 960.3-4 Environmental impacts. Environmental impacts shall be considered by the DOE throughout the site characterization, site selection, and repository development..., during site characterization and repository construction, operation, closure, and decommissioning. ...

  8. Identification of early cancerous lesion of esophagus with endoscopic images by hyperspectral image technique (Conference Presentation)

    NASA Astrophysics Data System (ADS)

    Huang, Shih-Wei; Chen, Shih-Hua; Chen, Weichung; Wu, I.-Chen; Wu, Ming Tsang; Kuo, Chie-Tong; Wang, Hsiang-Chen

    2016-03-01

    This study presents a method to identify early esophageal cancer within endoscope using hyperspectral imaging technology. The research samples are three kinds of endoscopic images including white light endoscopic, chromoendoscopic, and narrow-band endoscopic images with different stages of pathological changes (normal, dysplasia, dysplasia - esophageal cancer, and esophageal cancer). Research is divided into two parts: first, we analysis the reflectance spectra of endoscopic images with different stages to know the spectral responses by pathological changes. Second, we identified early cancerous lesion of esophagus by principal component analysis (PCA) of the reflectance spectra of endoscopic images. The results of this study show that the identification of early cancerous lesion is possible achieve from three kinds of images. In which the spectral characteristics of NBI endoscopy images of a gray area than those without the existence of the problem the first two, and the trend is very clear. Therefore, if simply to reflect differences in the degree of spectral identification, chromoendoscopic images are suitable samples. The best identification of early esophageal cancer is using the NBI endoscopic images. Based on the results, the use of hyperspectral imaging technology in the early endoscopic esophageal cancer lesion image recognition helps clinicians quickly diagnose. We hope for the future to have a relatively large amount of endoscopic image by establishing a hyperspectral imaging database system developed in this study, so the clinician can take this repository more efficiently preliminary diagnosis.

  9. Uncertainty and sensitivity analysis for two-phase flow in the vicinity of the repository in the 1996 performance assessment for the Waste Isolation Pilot Plant: Disturbed conditions

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    HELTON,JON CRAIG; BEAN,J.E.; ECONOMY,K.

    2000-05-22

    Uncertainty and sensitivity analysis results obtained in the 1996 performance assessment (PA) for the Waste Isolation Pilot Plant (WIPP) are presented for two-phase flow in the vicinity of the repository under disturbed conditions resulting from drilling intrusions. Techniques based on Latin hypercube sampling, examination of scatterplots, stepwise regression analysis, partial correlation analysis and rank transformations are used to investigate brine inflow, gas generation repository pressure, brine saturation and brine and gas outflow. Of the variables under study, repository pressure and brine flow from the repository to the Culebra Dolomite are potentially the most important in PA for the WIPP. Subsequentmore » to a drilling intrusion repository pressure was dominated by borehole permeability and generally below the level (i.e., 8 MPa) that could potentially produce spallings and direct brine releases. Brine flow from the repository to the Culebra Dolomite tended to be small or nonexistent with its occurrence and size also dominated by borehole permeability.« less

  10. Sensitivity tests to define the source apportionment performance criteria in the DeltaSA tool

    NASA Astrophysics Data System (ADS)

    Pernigotti, Denise; Belis, Claudio A.

    2017-04-01

    Identification and quantification of the contribution of emission sources to a given area is a key task for the design of abatement strategies. Moreover, European member states are obliged to report this kind of information for zones where the pollution levels exceed the limit values. At present, little is known about the performance and uncertainty of the variety of methodologies used for source apportionment and the comparability between the results of studies using different approaches. The source apportionment Delta (SA Delta) is a tool developed by the EC-JRC to support the particulate matter source apportionment modellers in the identification of sources (for factor analysis studies) and/or in the measure of their performance. The source identification is performed by the tool measuring the proximity of any user chemical profile to preloaded repository data (SPECIATE and SPECIEUROPE). The model performances criteria are based on standard statistical indexes calculated by comparing participants' source contribute estimates and their time series with preloaded references data. Those preloaded data refer to previous European SA intercomparison exercises: the first with real world data (22 participants), the second with synthetic data (25 participants) and the last with real world data which was also extended to Chemical Transport Models (38 receptor models and 4 CTMs). The references used for the model performances are 'true' (predefined by JRC) for the synthetic while they are calculated as ensemble average of the participants' results in real world intercomparisons. The candidates used for each source ensemble reference calculation were selected among participants results based on a number of consistency checks plus the similarity between their chemical profiles to the repository measured data. The estimation of the ensemble reference uncertainty is crucial in order to evaluate the users' performances against it. For this reason a sensitivity analysis on different methods to estimate the ensemble references' uncertainties was performed re-analyzing the synthetic intercomparison dataset, the only one where 'true' reference and ensemble reference contributions were both present. The Delta SA is now available on-line and will be presented, with a critical discussion of the sensitivity analysis on the ensemble reference uncertainty. In particular the grade of among participants mutual agreement on the presence of a certain source should be taken into account. Moreover also the importance of the synthetic intercomparisons in order to catch receptor models common biases will be stressed.

  11. What is the Value Proposition of Persistent Identifiers?

    NASA Astrophysics Data System (ADS)

    Klump, Jens; Huber, Robert

    2017-04-01

    Persistent identifiers (PID) are widely used today in scientific communication and documentation. Global unique identification plus persistent resolution of links to referenced digital research objects have been strong selling points for PID Systems as enabling technical infrastructures. Novel applications of PID Systems in research now go beyond the identification of file based objects such as literature or data sets and include the identification of dynamically changing datasets accessed through web services, physical objects, persons and organisations. But not only do we see more use cases but also a proliferation of identifier systems. An analysis of PID Systems used by 1381 repositories listed in the Registry of Research Data Repositories (re3data.org, status of 14 Dec 2015) showed that many disciplinary data repositories make use of PID that are not among the systems promoted by the libraries and publishers (DOI, PURL, ARK). This indicates that a number of communities have developed their own PID Systems. This begs the question, do we need more identifier systems? What makes their value proposition more appealing than those of already existing systems? On the other hand, some of these new use cases deal with entities outside the digital domain, the original scope of application for PIDs. It is therefore necessary to critically appraise the value propositions of available PID Systems and compare these against the requirements of new use cases for PID. Undoubtedly, DOI are the most used persistent identifier in scholarly communication. It was originally designed "to link customers with publishers, facilitate electronic commerce, and enable copyright management systems." Today, the DOI system is described as providing "a technical and social infrastructure for the registration and use of persistent interoperable identifiers for use on digital networks". This example shows how value propositions can change over time. Additional value can be gained by cross-linking between PID Systems, thus allowing new scholarly documentation and evaluation methods such as documenting the track record of researchers in publications and successful funding proposals, apply advanced bibliometric approaches, estimate the output and impact of funding, assess the reuse and subsequent impact of data publications, demonstrate the efficient use of research infrastructures, etc. This recombination of systems raise a series of new expectations and each stakeholder group may have its own vision of the benefits and value proposition of PIDs, which might be in conflict with others. New PID applications will arise with the application of PID Systems to semantic web technologies and to the Internet of Things, which extend PID applications to beyond digital objects to concepts and things, respectively, raising yet again their own expectations and value propositions. What are we trying to identify? What is the purpose served by identifying it? What are the implications for semantic web technologies? How certain can we be about the identity of an object and its state changes over time (Ship of Theseus Paradox)? In this presentation we will discuss a number of PID use cases and match these against the value propositions offered by a selection of PID Systems.

  12. DOE Office of Scientific and Technical Information (OSTI.GOV)

    Ferrada, J.J.

    This report compiles preliminary information that supports the premise that a repository is needed in Latin America and analyzes the nuclear situation (mainly in Argentina and Brazil) in terms of nuclear capabilities, inventories, and regional spent-fuel repositories. The report is based on several sources and summarizes (1) the nuclear capabilities in Latin America and establishes the framework for the need of a permanent repository, (2) the International Atomic Energy Agency (IAEA) approach for a regional spent-fuel repository and describes the support that international institutions are lending to this issue, (3) the current situation in Argentina in order to analyze themore » Argentinean willingness to find a location for a deep geological repository, and (4) the issues involved in selecting a location for the repository and identifies a potential location. This report then draws conclusions based on an analysis of this information. The focus of this report is mainly on spent fuel and does not elaborate on other radiological waste sources.« less

  13. Influence analysis of Github repositories.

    PubMed

    Hu, Yan; Zhang, Jun; Bai, Xiaomei; Yu, Shuo; Yang, Zhuo

    2016-01-01

    With the support of cloud computing techniques, social coding platforms have changed the style of software development. Github is now the most popular social coding platform and project hosting service. Software developers of various levels keep entering Github, and use Github to save their public and private software projects. The large amounts of software developers and software repositories on Github are posing new challenges to the world of software engineering. This paper tries to tackle one of the important problems: analyzing the importance and influence of Github repositories. We proposed a HITS based influence analysis on graphs that represent the star relationship between Github users and repositories. A weighted version of HITS is applied to the overall star graph, and generates a different set of top influential repositories other than the results from standard version of HITS algorithm. We also conduct the influential analysis on per-month star graph, and study the monthly influence ranking of top repositories.

  14. Biological Web Service Repositories Review

    PubMed Central

    Urdidiales‐Nieto, David; Navas‐Delgado, Ismael

    2016-01-01

    Abstract Web services play a key role in bioinformatics enabling the integration of database access and analysis of algorithms. However, Web service repositories do not usually publish information on the changes made to their registered Web services. Dynamism is directly related to the changes in the repositories (services registered or unregistered) and at service level (annotation changes). Thus, users, software clients or workflow based approaches lack enough relevant information to decide when they should review or re‐execute a Web service or workflow to get updated or improved results. The dynamism of the repository could be a measure for workflow developers to re‐check service availability and annotation changes in the services of interest to them. This paper presents a review on the most well‐known Web service repositories in the life sciences including an analysis of their dynamism. Freshness is introduced in this paper, and has been used as the measure for the dynamism of these repositories. PMID:27783459

  15. Creation of Data Repositories to Advance Nursing Science.

    PubMed

    Perazzo, Joseph; Rodriguez, Margaret; Currie, Jackson; Salata, Robert; Webel, Allison R

    2017-12-01

    Data repositories are a strategy in line with precision medicine and big data initiatives, and are an efficient way to maximize data utility and form collaborative research relationships. Nurse researchers are uniquely positioned to make a valuable contribution using this strategy. The purpose of this article is to present a review of the benefits and challenges associated with developing data repositories, and to describe the process we used to develop and maintain a data repository in HIV research. Systematic planning, data collection, synthesis, and data sharing have enabled us to conduct robust cross-sectional and longitudinal analyses with more than 200 people living with HIV. Our repository building has also led to collaboration and training, both in and out of our organization. We present a pragmatic and affordable way that nurse scientists can build and maintain a data repository, helping us continue to make to our understanding of health phenomena.

  16. Space Telecommunications Radio System (STRS) Application Repository Design and Analysis

    NASA Technical Reports Server (NTRS)

    Handler, Louis M.

    2013-01-01

    The Space Telecommunications Radio System (STRS) Application Repository Design and Analysis document describes the STRS application repository for software-defined radio (SDR) applications intended to be compliant to the STRS Architecture Standard. The document provides information about the submission of artifacts to the STRS application repository, to provide information to the potential users of that information, and for the systems engineer to understand the requirements, concepts, and approach to the STRS application repository. The STRS application repository is intended to capture knowledge, documents, and other artifacts for each waveform application or other application outside of its project so that when the project ends, the knowledge is retained. The document describes the transmission of technology from mission to mission capturing lessons learned that are used for continuous improvement across projects and supporting NASA Procedural Requirements (NPRs) for performing software engineering projects and NASAs release process.

  17. [The subject repositories of strategy of the Open Access initiative].

    PubMed

    Soares Guimarães, M C; da Silva, C H; Horsth Noronha, I

    2012-11-01

    The subject repositories are defined as a set of digital objects resulting from the research related to a specific disciplinary field and occupy a still restricted space in the discussion agenda of the Free Access Movement when compared to amplitude reached in the discussion of Institutional Repositories. Although the Subject Repository comes to prominence in the field, especially for the success of initiatives such as the arXiv, PubMed and E-prints, the literature on the subject is recognized as very limited. Despite its roots in the Library and Information Science, and focus on the management of disciplinary collections (subject area literature), there is little information available about the development and management of subject repositories. The following text seeks to make a brief summary on the topic as a way to present the potential to develop subject repositories in order to strengthen the initiative of open access.

  18. A Safety Case Approach for Deep Geologic Disposal of DOE HLW and DOE SNF in Bedded Salt - 13350

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Sevougian, S. David; MacKinnon, Robert J.; Leigh, Christi D.

    2013-07-01

    The primary objective of this study is to investigate the feasibility and utility of developing a defensible safety case for disposal of United States Department of Energy (U.S. DOE) high-level waste (HLW) and DOE spent nuclear fuel (SNF) in a conceptual deep geologic repository that is assumed to be located in a bedded salt formation of the Delaware Basin [1]. A safety case is a formal compilation of evidence, analyses, and arguments that substantiate and demonstrate the safety of a proposed or conceptual repository. We conclude that a strong initial safety case for potential licensing can be readily compiled bymore » capitalizing on the extensive technical basis that exists from prior work on the Waste Isolation Pilot Plant (WIPP), other U.S. repository development programs, and the work published through international efforts in salt repository programs such as in Germany. The potential benefits of developing a safety case include leveraging previous investments in WIPP to reduce future new repository costs, enhancing the ability to effectively plan for a repository and its licensing, and possibly expediting a schedule for a repository. A safety case will provide the necessary structure for organizing and synthesizing existing salt repository science and identifying any issues and gaps pertaining to safe disposal of DOE HLW and DOE SNF in bedded salt. The safety case synthesis will help DOE to plan its future R and D activities for investigating salt disposal using a risk-informed approach that prioritizes test activities that include laboratory, field, and underground investigations. It should be emphasized that the DOE has not made any decisions regarding the disposition of DOE HLW and DOE SNF. Furthermore, the safety case discussed herein is not intended to either site a repository in the Delaware Basin or preclude siting in other media at other locations. Rather, this study simply presents an approach for accelerated development of a safety case for a potential DOE HLW and DOE SNF repository using the currently available technical basis for bedded salt. This approach includes a summary of the regulatory environment relevant to disposal of DOE HLW and DOE SNF in a deep geologic repository, the key elements of a safety case, the evolution of the safety case through the successive phases of repository development and licensing, and the existing technical basis that could be used to substantiate the safety of a geologic repository if it were to be sited in the Delaware Basin. We also discuss the potential role of an underground research laboratory (URL). (authors)« less

  19. New Features of the re3data Registry of Research Data Repositories

    NASA Astrophysics Data System (ADS)

    Elger, K.; Pampel, H.; Vierkant, P.; Witt, M.

    2016-12-01

    re3data is a registry of research data repositories that lists over 1,600 repositories from around the world, making it the largest and most comprehensive online catalog of data repositories on the web. The registry offers researchers, funding agencies, libraries and publishers a comprehensive overview of the heterogeneous landscape of data repositories. The repositories are described, following the "Metadata Schema for the Description of Research Data Repositories". re3data summarises the properties of a repository into a user-friendly icon system helping users to easily identify an adequate repository for the storage of their datasets. The re3data entries are curated by an international, multi-disciplinary editorial board. An application programming interface (API) enables other information systems to list and fetch metadata for integration and interoperability. Funders like the European Commission (2015) and publishers like Springer Nature (2016) recommend the use of re3data.org in their policies. The original re3data project partners are the GFZ German Research Centre for Geosciences, the Humboldt-Universität zu Berlin, the Purdue University Libraries and the Karlsruhe Institute of Technology (KIT). Since 2015 re3data is operated as a service of DataCite, a global non-profit organisation that provides persistent identifiers (DOIs) for research data. At the 2016 AGU Fall Meeting we will describe the current status of re3data. An overview of the major developments and new features will be given. Furthermore, we will present our plans to increase the quality of the re3data entries.

  20. 10 CFR 960.5-2-3 - Meteorology.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REPOSITORY Preclosure Guidelines Preclosure Radiological Safety § 960.5-2-3 Meteorology. (a) Qualifying condition. The site shall be located such that expected meteorological conditions during repository.... Prevailing meteorological conditions such that any radioactive releases to the atmosphere during repository...

  1. Enabling comparative modeling of closely related genomes: Example genus Brucella

    DOE PAGES

    Faria, José P.; Edirisinghe, Janaka N.; Davis, James J.; ...

    2014-03-08

    For many scientific applications, it is highly desirable to be able to compare metabolic models of closely related genomes. In this study, we attempt to raise awareness to the fact that taking annotated genomes from public repositories and using them for metabolic model reconstructions is far from being trivial due to annotation inconsistencies. We are proposing a protocol for comparative analysis of metabolic models on closely related genomes, using fifteen strains of genus Brucella, which contains pathogens of both humans and livestock. This study lead to the identification and subsequent correction of inconsistent annotations in the SEED database, as wellmore » as the identification of 31 biochemical reactions that are common to Brucella, which are not originally identified by automated metabolic reconstructions. We are currently implementing this protocol for improving automated annotations within the SEED database and these improvements have been propagated into PATRIC, Model-SEED, KBase and RAST. This method is an enabling step for the future creation of consistent annotation systems and high-quality model reconstructions that will support in predicting accurate phenotypes such as pathogenicity, media requirements or type of respiration.« less

  2. Enabling comparative modeling of closely related genomes: Example genus Brucella

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Faria, José P.; Edirisinghe, Janaka N.; Davis, James J.

    For many scientific applications, it is highly desirable to be able to compare metabolic models of closely related genomes. In this study, we attempt to raise awareness to the fact that taking annotated genomes from public repositories and using them for metabolic model reconstructions is far from being trivial due to annotation inconsistencies. We are proposing a protocol for comparative analysis of metabolic models on closely related genomes, using fifteen strains of genus Brucella, which contains pathogens of both humans and livestock. This study lead to the identification and subsequent correction of inconsistent annotations in the SEED database, as wellmore » as the identification of 31 biochemical reactions that are common to Brucella, which are not originally identified by automated metabolic reconstructions. We are currently implementing this protocol for improving automated annotations within the SEED database and these improvements have been propagated into PATRIC, Model-SEED, KBase and RAST. This method is an enabling step for the future creation of consistent annotation systems and high-quality model reconstructions that will support in predicting accurate phenotypes such as pathogenicity, media requirements or type of respiration.« less

  3. New directions in medical e-curricula and the use of digital repositories.

    PubMed

    Fleiszer, David M; Posel, Nancy H; Steacy, Sean P

    2004-03-01

    Medical educators involved in the growth of multimedia-enhanced e-curricula are increasingly aware of the need for digital repositories to catalogue, store and ensure access to learning objects that are integrated within their online material. The experience at the Faculty of Medicine at McGill University during initial development of a mainstream electronic curriculum reflects this growing recognition that repositories can facilitate the development of a more comprehensive as well as effective electronic curricula. Also, digital repositories can help to ensure efficient utilization of resources through the use, re-use, and reprocessing of multimedia learning, addressing the potential for collaboration among repositories and increasing available material exponentially. The authors review different approaches to the development of a digital repository application, as well as global and specific issues that should be examined in the initial requirements definition and development phase, to ensure current initiatives meet long-term requirements. Often, decisions regarding creation of e-curricula and associated digital repositories are left to interested faculty and their individual development teams. However, the development of an e-curricula and digital repository is not predominantly a technical exercise, but rather one that affects global pedagogical strategies and curricular content and involves a commitment of large-scale resources. Outcomes of these decisions can have long-term consequences and as such, should involve faculty at the highest levels including the dean.

  4. A Prototype Performance Assessment Model for Generic Deep Borehole Repository for High-Level Nuclear Waste - 12132

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Lee, Joon H.; Arnold, Bill W.; Swift, Peter N.

    2012-07-01

    A deep borehole repository is one of the four geologic disposal system options currently under study by the U.S. DOE to support the development of a long-term strategy for geologic disposal of commercial used nuclear fuel (UNF) and high-level radioactive waste (HLW). The immediate goal of the generic deep borehole repository study is to develop the necessary modeling tools to evaluate and improve the understanding of the repository system response and processes relevant to long-term disposal of UNF and HLW in a deep borehole. A prototype performance assessment model for a generic deep borehole repository has been developed using themore » approach for a mined geological repository. The preliminary results from the simplified deep borehole generic repository performance assessment indicate that soluble, non-sorbing (or weakly sorbing) fission product radionuclides, such as I-129, Se-79 and Cl-36, are the likely major dose contributors, and that the annual radiation doses to hypothetical future humans associated with those releases may be extremely small. While much work needs to be done to validate the model assumptions and parameters, these preliminary results highlight the importance of a robust seal design in assuring long-term isolation, and suggest that deep boreholes may be a viable alternative to mined repositories for disposal of both HLW and UNF. (authors)« less

  5. Thermal Analysis of a Nuclear Waste Repository in Argillite Host Rock

    NASA Astrophysics Data System (ADS)

    Hadgu, T.; Gomez, S. P.; Matteo, E. N.

    2017-12-01

    Disposal of high-level nuclear waste in a geological repository requires analysis of heat distribution as a result of decay heat. Such an analysis supports design of repository layout to define repository footprint as well as provide information of importance to overall design. The analysis is also used in the study of potential migration of radionuclides to the accessible environment. In this study, thermal analysis for high-level waste and spent nuclear fuel in a generic repository in argillite host rock is presented. The thermal analysis utilized both semi-analytical and numerical modeling in the near field of a repository. The semi-analytical method looks at heat transport by conduction in the repository and surroundings. The results of the simulation method are temperature histories at selected radial distances from the waste package. A 3-D thermal-hydrologic numerical model was also conducted to study fluid and heat distribution in the near field. The thermal analysis assumed a generic geological repository at 500 m depth. For the semi-analytical method, a backfilled closed repository was assumed with basic design and material properties. For the thermal-hydrologic numerical method, a repository layout with disposal in horizontal boreholes was assumed. The 3-D modeling domain covers a limited portion of the repository footprint to enable a detailed thermal analysis. A highly refined unstructured mesh was used with increased discretization near heat sources and at intersections of different materials. All simulations considered different parameter values for properties of components of the engineered barrier system (i.e. buffer, disturbed rock zone and the host rock), and different surface storage times. Results of the different modeling cases are presented and include temperature and fluid flow profiles in the near field at different simulation times. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology and Engineering Solutions of Sandia, LLC., a wholly owned subsidiary of Honeywell International, Inc., for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-NA-0003525. SAND2017-8295 A.

  6. 10 CFR 960.5-2-5 - Environmental quality.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REPOSITORY Preclosure Guidelines Environment, Socioeconomics, and Transportation § 960.5-2-5 Environmental... repository siting, construction, operation, closure, and decommissioning, and projected environmental impacts... of the repository or its support facilities on, a component of the National Park System, the National...

  7. 10 CFR 60.1 - Purpose and scope.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN GEOLOGIC REPOSITORIES General..., special nuclear, and byproduct material at a geologic repository operations area sited, constructed, or... at a geologic repository operations area sited, constructed, or operated at Yucca Mountain, Nevada...

  8. 10 CFR 60.31 - Construction authorization.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REPOSITORIES Licenses Construction Authorization § 60.31 Construction authorization. Upon review and... in a geologic repository operations area of the design proposed without unreasonable risk to the...: (1) DOE has described the proposed geologic repository including but not limited to: (i) The geologic...

  9. 10 CFR 960.5-2-6 - Socioeconomic impacts.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REPOSITORY Preclosure Guidelines Environment, Socioeconomics, and Transportation § 960.5-2-6 Socioeconomic... and/or economic impacts induced in communities and surrounding regions by repository siting... significant repository-related impacts on community services, housing supply and demand, and the finances of...

  10. 10 CFR 60.15 - Site characterization.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN GEOLOGIC REPOSITORIES Licenses... the geologic repository to the extent practical. (2) The number of exploratory boreholes and shafts... characterization. (3) To the extent practical, exploratory boreholes and shafts in the geologic repository...

  11. 10 CFR 960.5-1 - System guidelines.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REPOSITORY Preclosure Guidelines § 960.5-1 System guidelines. (a) Qualifying conditions—(1) Preclosure... radioactive materials to restricted and unrestricted areas during repository operation and closure shall meet... repository siting, construction, operation, closure, and decommissioning the public and the environment shall...

  12. A scoping review of online repositories of quality improvement projects, interventions and initiatives in healthcare.

    PubMed

    Bytautas, Jessica P; Gheihman, Galina; Dobrow, Mark J

    2017-04-01

    Quality improvement (QI) is becoming an important focal point for health systems. There is increasing interest among health system stakeholders to learn from and share experiences on the use of QI methods and approaches in their work. Yet there are few easily accessible, online repositories dedicated to documenting QI activity. We conducted a scoping review of publicly available, web-based QI repositories to (i) identify current approaches to sharing information on QI practices; (ii) categorise these approaches based on hosting, scope and size, content acquisition and eligibility, content format and search, and evaluation and engagement characteristics; and (iii) review evaluations of the design, usefulness and impact of their online QI practice repositories. The search strategy consisted of traditional database and grey literature searches, as well as expert consultation, with the ultimate aim of identifying and describing QI repositories of practices undertaken in a healthcare context. We identified 13 QI repositories and found substantial variation across the five categories. The QI repositories used different terminology (eg, practices vs case studies) and approaches to content acquisition, and varied in terms of primary areas of focus. All provided some means for organising content according to categories or themes and most provided at least rudimentary keyword search functionality. Notably, none of the QI repositories included evaluations of their impact. With growing interest in sharing and spreading best practices and increasing reliance on QI as a key contributor to health system performance, the role of QI repositories is likely to expand. Designing future QI repositories based on knowledge of the range and type of features available is an important starting point for improving their usefulness and impact. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

  13. Migration of the Gaudi and LHCb software repositories from CVS to Subversion

    NASA Astrophysics Data System (ADS)

    Clemencic, M.; Degaudenzi, H.; LHCb Collaboration

    2011-12-01

    A common code repository is of primary importance in a distributed development environment such as large HEP experiments. CVS (Concurrent Versions System) has been used in the past years at CERN for the hosting of shared software repositories, among which were the repositories for the Gaudi Framework and the LHCb software projects. Many developers around the world produced alternative systems to share code and revisions among several developers, mainly to overcome the limitations in CVS, and CERN has recently started a new service for code hosting based on the version control system Subversion. The differences between CVS and Subversion and the way the code was organized in Gaudi and LHCb CVS repositories required careful study and planning of the migration. Special care was used to define the organization of the new Subversion repository. To avoid as much as possible disruption in the development cycle, the migration has been gradual with the help of tools developed explicitly to hide the differences between the two systems. The principles guiding the migration steps, the organization of the Subversion repository and the tools developed will be presented, as well as the problems encountered both from the librarian and the user points of view.

  14. ROSA P : The National Transportation Library’s Repository and Open Science Access Portal

    DOT National Transportation Integrated Search

    2018-01-01

    The National Transportation Library (NTL) was founded as an all-digital repository of US DOT research reports, technical publications and data products. NTLs primary public offering is ROSA P, the Repository and Open Science Access Portal. An open...

  15. 10 CFR 960.3-3 - Consultation.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... ENERGY GENERAL GUIDELINES FOR THE PRELIMINARY SCREENING OF POTENTIAL SITES FOR A NUCLEAR WASTE REPOSITORY..., operation, closure, decommissioning, licensing, or regulation of a repository. Written responses to written... purpose of determining the suitability of such area for the development of a repository, the DOE shall...

  16. 10 CFR 60.32 - Conditions of construction authorization.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... GEOLOGIC REPOSITORIES Licenses Construction Authorization § 60.32 Conditions of construction authorization... changes to the features of the geologic repository and the procedures authorized. The restrictions that... setting as well as measures related to the design and construction of the geologic repository operations...

  17. An Automated Acquisition System for Media Exploitation

    DTIC Science & Technology

    2008-06-01

    on the acquisition station, AcqMan will pull out the SHA256 image hash, and the device’s model, serial number, and manufacturer. 2. Query the ADOMEX...Repository Using the data collected above, AcqMan will query the ADOMEX repository. The ADOMEX repository will respond to the query with the SHA256 ’s of...whose SHA256s do not match. The last category will be a list of images that the ADOMEX repository already has and that the acquisition station can

  18. Case for retrievable high-level nuclear waste disposal

    USGS Publications Warehouse

    Roseboom, Eugene H.

    1994-01-01

    Plans for the nation's first high-level nuclear waste repository have called for permanently closing and sealing the repository soon after it is filled. However, the hydrologic environment of the proposed site at Yucca Mountain, Nevada, should allow the repository to be kept open and the waste retrievable indefinitely. This would allow direct monitoring of the repository and maintain the options for future generations to improve upon the disposal methods or use the uranium in the spent fuel as an energy resource.

  19. ProCon - PROteomics CONversion tool.

    PubMed

    Mayer, Gerhard; Stephan, Christian; Meyer, Helmut E; Kohl, Michael; Marcus, Katrin; Eisenacher, Martin

    2015-11-03

    With the growing amount of experimental data produced in proteomics experiments and the requirements/recommendations of journals in the proteomics field to publicly make available data described in papers, a need for long-term storage of proteomics data in public repositories arises. For such an upload one needs proteomics data in a standardized format. Therefore, it is desirable, that the proprietary vendor's software will integrate in the future such an export functionality using the standard formats for proteomics results defined by the HUPO-PSI group. Currently not all search engines and analysis tools support these standard formats. In the meantime there is a need to provide user-friendly free-to-use conversion tools that can convert the data into such standard formats in order to support wet-lab scientists in creating proteomics data files ready for upload into the public repositories. ProCon is such a conversion tool written in Java for conversion of proteomics identification data into standard formats mzIdentML and Pride XML. It allows the conversion of Sequest™/Comet .out files, of search results from the popular and often used ProteomeDiscoverer® 1.x (x=versions 1.1 to1.4) software and search results stored in the LIMS systems ProteinScape® 1.3 and 2.1 into mzIdentML and PRIDE XML. This article is part of a Special Issue entitled: Computational Proteomics. Copyright © 2015. Published by Elsevier B.V.

  20. Using patient lists to add value to integrated data repositories.

    PubMed

    Wade, Ted D; Zelarney, Pearlanne T; Hum, Richard C; McGee, Sylvia; Batson, Deborah H

    2014-12-01

    Patient lists are project-specific sets of patients that can be queried in integrated data repositories (IDR's). By allowing a set of patients to be an addition to the qualifying conditions of a query, returned results will refer to, and only to, that set of patients. We report a variety of use cases for such lists, including: restricting retrospective chart review to a defined set of patients; following a set of patients for practice management purposes; distributing "honest-brokered" (deidentified) data; adding phenotypes to biosamples; and enhancing the content of study or registry data. Among the capabilities needed to implement patient lists in an IDR are: capture of patient identifiers from a query and feedback of these into the IDR; the existence of a permanent internal identifier in the IDR that is mappable to external identifiers; the ability to add queryable attributes to the IDR; the ability to merge data from multiple queries; and suitable control over user access and de-identification of results. We implemented patient lists in a custom IDR of our own design. We reviewed capabilities of other published IDRs for focusing on sets of patients. The widely used i2b2 IDR platform has various ways to address patient sets, and it could be modified to add the low-overhead version of patient lists that we describe. Copyright © 2014 Elsevier Inc. All rights reserved.

  1. Trustworthy Digital Repositories: Building Trust the Old Fashion Way, EARNING IT.

    NASA Astrophysics Data System (ADS)

    Kinkade, D.; Chandler, C. L.; Shepherd, A.; Rauch, S.; Groman, R. C.; Wiebe, P. H.; Glover, D. M.; Allison, M. D.; Copley, N. J.; Ake, H.; York, A.

    2016-12-01

    There are several drivers increasing the importance of high quality data management and curation in today's research process (e.g., OSTP PARR memo, journal publishers, funders, academic and private institutions), and proper management is necessary throughout the data lifecycle to enable reuse and reproducibility of results. Many digital data repositories are capable of satisfying the basic management needs of an investigator looking to share their data (i.e., publish data in the public domain), but repository services vary greatly and not all provide mature services that facilitate discovery, access, and reuse of research data. Domain-specific repositories play a vital role in the data curation process by working closely with investigators to create robust metadata, perform first order QC, and assemble and publish research data. In addition, they may employ technologies and services that enable increased discovery, access, and long-term archive. However, smaller domain facilities operate in varying states of capacity and curation ability. Within this repository environment, individual investigators (driven by publishers, funders, or institutions) need to find trustworthy repositories for their data; and funders need to direct investigators to quality repositories to ensure return on their investment. So, how can one determine the best home for valuable research data? Metrics can be applied to varying aspects of data curation, and many credentialing organizations offer services that assess and certify the trustworthiness of a given data management facility. Unfortunately, many of these certifications can be inaccessible to a small repository in cost, time, or scope. Are there alternatives? This presentation will discuss methods and approaches used by the Biological and Chemical Oceanography Data Management Office (BCO-DMO; a domain-specific, intermediate digital data repository) to demonstrate trustworthiness in the face of a daunting accreditation landscape.

  2. 10 CFR 960.4 - Postclosure guidelines.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REPOSITORY Postclosure Guidelines § 960.4 Postclosure guidelines. The guidelines in this subpart specify the factors to be considered in evaluating and comparing sites on the basis of expected repository performance... NRC and EPA regulations. These requirements must be met by the repository system, which contains...

  3. 10 CFR 60.3 - License required.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN GEOLOGIC REPOSITORIES General... byproduct material at a geologic repository operations area except as authorized by a license issued by the Commission pursuant to this part. (b) DOE shall not commence construction of a geologic repository operations...

  4. Asset Reuse of Images from a Repository

    ERIC Educational Resources Information Center

    Herman, Deirdre

    2014-01-01

    According to Markus's theory of reuse, when digital repositories are deployed to collect and distribute organizational assets, they supposedly help ensure accountability, extend information exchange, and improve productivity. Such repositories require a large investment due to the continuing costs of hardware, software, user licenses, training,…

  5. 10 CFR 60.17 - Contents of site characterization plan.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... GEOLOGIC REPOSITORIES Licenses Preapplication Review § 60.17 Contents of site characterization plan. The... construction authorization for a geologic repository operations area; (4) Criteria, developed pursuant to... area for the location of a geologic repository; and (5) Any other information which the Commission, by...

  6. 10 CFR 960.4-2-2 - Geochemistry.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REPOSITORY Postclosure Guidelines § 960.4-2-2 Geochemistry. (a) Qualifying condition. The present and... future, not affect or would favorably affect the ability of the geologic repository to isolate the waste... subjected to expected repository conditions, would remain unaltered or would alter to mineral assemblages...

  7. 17 CFR 49.3 - Procedures for registration.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... if the Commission finds that such swap data repository is appropriately organized, and has the...) SWAP DATA REPOSITORIES § 49.3 Procedures for registration. (a) Application procedures. (1) An applicant, person or entity desiring to be registered as a swap data repository shall file electronically an...

  8. Biological Web Service Repositories Review.

    PubMed

    Urdidiales-Nieto, David; Navas-Delgado, Ismael; Aldana-Montes, José F

    2017-05-01

    Web services play a key role in bioinformatics enabling the integration of database access and analysis of algorithms. However, Web service repositories do not usually publish information on the changes made to their registered Web services. Dynamism is directly related to the changes in the repositories (services registered or unregistered) and at service level (annotation changes). Thus, users, software clients or workflow based approaches lack enough relevant information to decide when they should review or re-execute a Web service or workflow to get updated or improved results. The dynamism of the repository could be a measure for workflow developers to re-check service availability and annotation changes in the services of interest to them. This paper presents a review on the most well-known Web service repositories in the life sciences including an analysis of their dynamism. Freshness is introduced in this paper, and has been used as the measure for the dynamism of these repositories. © 2017 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

  9. Finding relevant biomedical datasets: the UC San Diego solution for the bioCADDIE Retrieval Challenge

    PubMed Central

    Wei, Wei; Ji, Zhanglong; He, Yupeng; Zhang, Kai; Ha, Yuanchi; Li, Qi; Ohno-Machado, Lucila

    2018-01-01

    Abstract The number and diversity of biomedical datasets grew rapidly in the last decade. A large number of datasets are stored in various repositories, with different formats. Existing dataset retrieval systems lack the capability of cross-repository search. As a result, users spend time searching datasets in known repositories, and they typically do not find new repositories. The biomedical and healthcare data discovery index ecosystem (bioCADDIE) team organized a challenge to solicit new indexing and searching strategies for retrieving biomedical datasets across repositories. We describe the work of one team that built a retrieval pipeline and examined its performance. The pipeline used online resources to supplement dataset metadata, automatically generated queries from users’ free-text questions, produced high-quality retrieval results and achieved the highest inferred Normalized Discounted Cumulative Gain among competitors. The results showed that it is a promising solution for cross-database, cross-domain and cross-repository biomedical dataset retrieval. Database URL: https://github.com/w2wei/dataset_retrieval_pipeline PMID:29688374

  10. The Nevada initiative: A risk communication Fiasco

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Flynn, J.; Solvic, P.; Mertz, C.K.

    The U.S. Congress has designated Yucca Mountain, Nevada as the only potential site to be studied for the nation`s first high-level nuclear waste repository. People in Nevada strongly oppose the program, managed by the U.S. Department of Energy. Survey research shows that the public believes there are great risks from a repository program, in contrast to a majority of scientists who feel the risks are acceptably small. Delays in the repository program resulting in part from public opposition in Nevada have concerned the nuclear power industry, which collects the fees for the federal repository program and believes it needs themore » repository as a final disposal facility for its high-level nuclear wastes. To assist the repository program, the American Nuclear Energy Council (ANEC), an industry group, sponsored a massive advertising campaign in Nevada. The campaign attempted to assure people that the risks of a repository were small and that the repository studies should proceed. The campaign failed because its managers misunderstood the issues underlying the controversy, attempted a covert manipulation of public opinion that was revealed, and most importantly, lacked the public trust that was necessary to communicate credibly about the risks of a nuclear waste facility. This article describes the advertising campaign and its effects. The manner in which the ANEC campaign itself became a controversial public issue is reviewed. The advertising campaign is discussed as it relates to risk assessment and communication. 29 refs., 2 tabs.« less

  11. Collaborative Information Retrieval Method among Personal Repositories

    NASA Astrophysics Data System (ADS)

    Kamei, Koji; Yukawa, Takashi; Yoshida, Sen; Kuwabara, Kazuhiro

    In this paper, we describe a collaborative information retrieval method among personal repositorie and an implementation of the method on a personal agent framework. We propose a framework for personal agents that aims to enable the sharing and exchange of information resources that are distributed unevenly among individuals. The kernel of a personal agent framework is an RDF(resource description framework)-based information repository for storing, retrieving and manipulating privately collected information, such as documents the user read and/or wrote, email he/she exchanged, web pages he/she browsed, etc. The repository also collects annotations to information resources that describe relationships among information resources and records of interaction between the user and information resources. Since the information resources in a personal repository and their structure are personalized, information retrieval from other users' is an important application of the personal agent. A vector space model with a personalized concept-base is employed as an information retrieval mechanism in a personal repository. Since a personalized concept-base is constructed from information resources in a personal repository, it reflects its user's knowledge and interests. On the other hand, it leads to another problem while querying other users' personal repositories; that is, simply transferring query requests does not provide desirable results. To solve this problem, we propose a query equalization scheme based on a relevance feedback method for collaborative information retrieval between personalized concept-bases. In this paper, we describe an implementation of the collaborative information retrieval method and its user interface on the personal agent framework.

  12. Organizing Scientific Data Sets: Studying Similarities and Differences in Metadata and Subject Term Creation

    ERIC Educational Resources Information Center

    White, Hollie C.

    2012-01-01

    Background: According to Salo (2010), the metadata entered into repositories are "disorganized" and metadata schemes underlying repositories are "arcane". This creates a challenging repository environment in regards to personal information management (PIM) and knowledge organization systems (KOSs). This dissertation research is…

  13. Worth the Work

    ERIC Educational Resources Information Center

    Schaffhauser, Dian

    2010-01-01

    Even in the age of Google, digital repositories can add tremendous value to an institution. Yet creating and maintaining these collections is no small task. Digital repository advocates will concede that the challenges in building and maintaining these collections can daunt even the most intrepid supporters. Three repository directors share their…

  14. Collaboration Nation: The Building of the Welsh Repository Network

    ERIC Educational Resources Information Center

    Knowles, Jacqueline

    2010-01-01

    Purpose: The purpose of this paper is to disseminate information about the Welsh Repository Network (WRN), innovative work being undertaken to build an integrated network of institutional digital repositories. A collaborative approach, in particular through the provision of centralised technical and organisational support, has demonstrated…

  15. 76 FR 81950 - Privacy Act; System of Records

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-29

    ... ``Consolidated Data Repository'' (09-90-1000). This system of records is being amended to include records... Repository'' (SORN 09-90-1000). OIG is adding record sources to the system. This system fulfills our..., and investigations of the Medicare and Medicaid programs. SYSTEM NAME: Consolidated Data Repository...

  16. 10 CFR 60.22 - Filing and distribution of application.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... GEOLOGIC REPOSITORIES Licenses License Applications § 60.22 Filing and distribution of application. (a) An application for a construction authorization for a high-level radioactive waste repository at a geologic repository operations area, and an application for a license to receive and possess source, special nuclear...

  17. 10 CFR 960.4-2-5 - Erosion.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... ENERGY GENERAL GUIDELINES FOR THE PRELIMINARY SCREENING OF POTENTIAL SITES FOR A NUCLEAR WASTE REPOSITORY... exhumation would not be expected to occur during the first one million years after repository closure. (c... the ability of the geologic repository to isolate the waste. (d) Disqualifying condition. The site...

  18. 76 FR 14057 - Notice of Inventory Completion: University of Wyoming, Anthropology Department, Human Remains...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-15

    ...: University of Wyoming, Anthropology Department, Human Remains Repository, Laramie, WY AGENCY: National Park... Anthropology Department, Human Remains Repository, Laramie, WY. The human remains and associated funerary... the human remains was made by University of Wyoming, Anthropology Department, Human Remains Repository...

  19. TRAC Searchable Research Library

    DTIC Science & Technology

    2016-05-01

    network accessible document repository for technical documents and similar document artifacts. We used a model-based approach using the Vector...demonstration and model refinement. 14. SUBJECT TERMS Knowledge Management, Document Repository , Digital Library, Vector Directional Data Model...27 Figure D1. Administrator Repository Upload Page. ................................................................... D-2 Figure D2

  20. 10 CFR 960.5-2-4 - Offsite installations and operations.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... SITES FOR A NUCLEAR WASTE REPOSITORY Preclosure Guidelines Preclosure Radiological Safety § 960.5-2-4... operations, including atomic energy defense activities, (1) will not significantly affect repository siting...), when considered together with emissions from repository operation and closure, will not be likely to...

  1. Microsoft Repository Version 2 and the Open Information Model.

    ERIC Educational Resources Information Center

    Bernstein, Philip A.; Bergstraesser, Thomas; Carlson, Jason; Pal, Shankar; Sanders, Paul; Shutt, David

    1999-01-01

    Describes the programming interface and implementation of the repository engine and the Open Information Model for Microsoft Repository, an object-oriented meta-data management facility that ships in Microsoft Visual Studio and Microsoft SQL Server. Discusses Microsoft's component object model, object manipulation, queries, and information…

  2. 10 CFR 2.1027 - Sua sponte.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Applicable to Proceedings for the Issuance of Licenses for the Receipt of High-Level Radioactive Waste at a... construction authorization for a high-level radioactive waste repository at a geologic repository operations...-level radioactive waste at a geologic repository operations area under parts 60 or 63 of this chapter...

  3. Modeling Coupled Processes in Clay Formations for Radioactive Waste Disposal

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Liu, Hui-Hai; Rutqvist, Jonny; Zheng, Liange

    As a result of the termination of the Yucca Mountain Project, the United States Department of Energy (DOE) has started to explore various alternative avenues for the disposition of used nuclear fuel and nuclear waste. The overall scope of the investigation includes temporary storage, transportation issues, permanent disposal, various nuclear fuel types, processing alternatives, and resulting waste streams. Although geologic disposal is not the only alternative, it is still the leading candidate for permanent disposal. The realm of geologic disposal also offers a range of geologic environments that may be considered, among those clay shale formations. Figure 1-1 presents themore » distribution of clay/shale formations within the USA. Clay rock/shale has been considered as potential host rock for geological disposal of high-level nuclear waste throughout the world, because of its low permeability, low diffusion coefficient, high retention capacity for radionuclides, and capability to self-seal fractures induced by tunnel excavation. For example, Callovo-Oxfordian argillites at the Bure site, France (Fouche et al., 2004), Toarcian argillites at the Tournemire site, France (Patriarche et al., 2004), Opalinus clay at the Mont Terri site, Switzerland (Meier et al., 2000), and Boom clay at Mol site, Belgium (Barnichon et al., 2005) have all been under intensive scientific investigations (at both field and laboratory scales) for understanding a variety of rock properties and their relations with flow and transport processes associated with geological disposal of nuclear waste. Clay/shale formations may be generally classified as indurated and plastic clays (Tsang et al., 2005). The latter (including Boom clay) is a softer material without high cohesion; its deformation is dominantly plastic. For both clay rocks, coupled thermal, hydrological, mechanical and chemical (THMC) processes are expected to have a significant impact on the long-term safety of a clay repository. For example, the excavation-damaged zone (EDZ) near repository tunnels can modify local permeability (resulting from induced fractures), potentially leading to less confinement capability (Tsang et al., 2005). Because of clay's swelling and shrinkage behavior (depending on whether the clay is in imbibition or drainage processes), fracture properties in the EDZ are quite dynamic and evolve over time as hydromechanical conditions change. To understand and model the coupled processes and their impact on repository performance is critical for the defensible performance assessment of a clay repository. Within the Natural Barrier System (NBS) group of the Used Fuel Disposition (UFD) Campaign at DOE's Office of Nuclear Energy, LBNL's research activities have focused on understanding and modeling such coupled processes. LBNL provided a report in this April on literature survey of studies on coupled processes in clay repositories and identification of technical issues and knowledge gaps (Tsang et al., 2010). This report will document other LBNL research activities within the natural system work package, including the development of constitutive relationships for elastic deformation of clay rock (Section 2), a THM modeling study (Section 3) and a THC modeling study (Section 4). The purpose of the THM and THC modeling studies is to demonstrate the current modeling capabilities in dealing with coupled processes in a potential clay repository. In Section 5, we discuss potential future R&D work based on the identified knowledge gaps. The linkage between these activities and related FEPs is presented in Section 6.« less

  4. Research on wild relatives of fruit and nut crops at the Davis repository

    USDA-ARS?s Scientific Manuscript database

    The USDA germplasm repository in Davis is responsible for acquiring, conserving and distributing a broad spectrum of diversity of subtropical and temperate fruit and nut species germplasm to stakeholders around the world. Currently the repository holds over 7000 accessions of germplasm including Act...

  5. 17 CFR 49.2 - Definitions.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... Commodity and Securities Exchanges COMMODITY FUTURES TRADING COMMISSION SWAP DATA REPOSITORIES § 49.2... indirectly, controls, is controlled by, or is under common control with, the swap data repository. (2) Asset... “commercial use” means the use of swap data held and maintained by a registered swap data repository for a...

  6. 17 CFR 49.2 - Definitions.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... Commodity and Securities Exchanges COMMODITY FUTURES TRADING COMMISSION SWAP DATA REPOSITORIES § 49.2... indirectly, controls, is controlled by, or is under common control with, the swap data repository. (2) Asset... “commercial use” means the use of swap data held and maintained by a registered swap data repository for a...

  7. 75 FR 54528 - Privacy Act of 1974: Implementation of Exemptions United States Citizenship and Immigration...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-09-08

    ... States Citizenship and Immigration Services-012 Citizenship and Immigration Data Repository System of... and Immigration Data Repository System of Records system of records and this proposed rulemaking. In... Repository (CIDR). The Privacy Act embodies fair information principles in a statutory framework governing...

  8. 10 CFR 60.41 - Standards for issuance of a license.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REPOSITORIES Licenses License Issuance and Amendment § 60.41 Standards for issuance of a license. A license to receive and possess source, special nuclear, or byproduct material at a geologic repository operations area may be issued by the Commission upon finding that: (a) Construction of the geologic repository...

  9. Factors Affecting Faculty Acceptance and Use of Institutional Repositories in Thailand

    ERIC Educational Resources Information Center

    Ammarukleart, Sujira

    2017-01-01

    Institutional repositories have been introduced as an innovative and alternative technology for scholarly communication and have received considerable attention from scholars across disciplines and around the globe. While some universities in Thailand have developed and implemented institutional repositories for nearly a decade, knowledge of the…

  10. Structure, Features, and Faculty Content in ARL Member Repositories

    ERIC Educational Resources Information Center

    Mercer, Holly; Koenig, Jay; McGeachin, Robert B.; Tucker, Sandra L.

    2011-01-01

    Questions about the optimal way to present repository content to authors, submitters, and end-users, prompted this study. The authors examined, through an observation and a survey, the institutional repositories of peer institutions in the ARL for good practices related to the presentation and organization of faculty-authored institutional…

  11. 75 FR 64643 - Reporting of Security-Based Swap Transaction Data

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-20

    ... information relating to pre-enactment security-based swaps to a registered security-based swap data repository... within 60 days after a registered security- based swap data repository commences operations to receive... repository,\\8\\ and security- based swap execution facility.\\9\\ The Commission has issued an advance notice of...

  12. 75 FR 16360 - Dan Kane; Receipt of Petition for Rulemaking

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-04-01

    ... certainties in light of the current administration's proposed defunding of the Yucca Mountain Repository for... construction of a mined geologic repository for spent nuclear fuel (Yucca Mountain) from the U.S. Department of... Mountain repository be discontinued for what the petitioner believes are political reasons. The petitioner...

  13. 76 FR 53454 - Privacy Act System of Records

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-08-26

    ... statutory responsibilities of the OIG; and Acting as a repository and source for information necessary to... in matters relating to the statutory responsibilities of the OIG; and 7. Acting as a repository and.... Acting as a repository and source for information necessary to fulfill the reporting requirements of the...

  14. 76 FR 14058 - Notice of Inventory Completion: University of Wyoming, Anthropology Department, Human Remains...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-15

    ...: University of Wyoming, Anthropology Department, Human Remains Repository, Laramie, WY AGENCY: National Park... Repository, Laramie, WY. The human remains were removed from the east side of the Big Horn Mountains in the... made by University of Wyoming, Anthropology Department, Human Remains Repository, professional staff in...

  15. Building Connections, Collections, and Communities: Increasing the Visibility and Impact of Extension through Institutional Repositories

    ERIC Educational Resources Information Center

    Inefuku, Harrison W.; Franz, Nancy K.

    2015-01-01

    Over the past 20 years, university libraries have developed and manage institutional repositories--digital libraries that provide free, public access to the research, scholarship, and publications of their university's faculty, staff, and students. Although underused by Extension professionals, institutional repositories are powerful tools that…

  16. 78 FR 16713 - Board Meeting; April 16, 2013; Richland, WA

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-03-18

    ... in a repository. Pursuant to its authority under section 5051 of Public Law 100-203, Nuclear Waste... facility in preparation for eventual disposal in a deep geologic repository. State, local, and regional... DOE's work related to the potential direct disposal in a deep geologic repository of existing SNF...

  17. Ontological Modeling of Educational Resources: A Proposed Implementation for Greek Schools

    ERIC Educational Resources Information Center

    Poulakakis, Yannis; Vassilakis, Kostas; Kalogiannakis, Michail; Panagiotakis, Spyros

    2017-01-01

    In eLearning context searching for suitable educational material is still a challenging issue. During the last two decades, various digital repositories, such as Learning Object Repositories, institutional repositories and latterly Open Educational Resources, have been developed to accommodate collections of learning material that can be used for…

  18. 76 FR 14062 - Notice of Inventory Completion: U.S. Department of the Interior, Bureau of Indian Affairs...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-15

    ... Department, Human Remains Repository, Laramie, WY AGENCY: National Park Service, Interior. ACTION: Notice..., and in the possession of the University of Wyoming, Anthropology Department, Human Remains Repository... University of Wyoming, Anthropology Department, Human Remains Repository, professional staff in consultation...

  19. Types of Online Hierarchical Repository Structures

    ERIC Educational Resources Information Center

    Hershkovitz, Arnon; Azran, Ronit; Hardof-Jaffe, Sharon; Nachmias, Rafi

    2011-01-01

    This study presents an empirical investigation of online hierarchical repositories of items presented to university students in Web-supported course websites, using Web mining methods. To this end, data from 1747 courses were collected, and the use of online repositories of content items in these courses was examined. At a later stage, courses…

  20. 10 CFR 960.3-1-4-2 - Site nomination for characterization.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... SITES FOR A NUCLEAR WASTE REPOSITORY Implementation Guidelines § 960.3-1-4-2 Site nomination for... types under expected repository conditions; evaluations of natural and man-made analogs of the repository and its subsystems, such as geothermally active areas, underground excavations, and case histories...

  1. 10 CFR 60.44 - Changes, tests, and experiments.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REPOSITORIES Licenses License Issuance and Amendment § 60.44 Changes, tests, and experiments. (a)(1) Following authorization to receive and possess source, special nuclear, or byproduct material at a geologic repository operations area, the DOE may (i) make changes in the geologic repository operations area as described in the...

  2. Evolution of a Digital Repository: One Institution's Experience

    ERIC Educational Resources Information Center

    Owen, Terry M.

    2011-01-01

    In this article, the development of a digital repository is examined, specifically how the focus on acquiring content for the repository has transitioned from faculty-published research to include the gray literature produced by the research centers on campus, including unpublished technical reports and undergraduate research from honors programs.…

  3. Embracing the Future: Embedding Digital Repositories in Higher Education Institutions. Research Brief

    ERIC Educational Resources Information Center

    Hoorens, Stijn; van Dijk, Lidia Villalba; van Stolk, Christian

    2009-01-01

    This briefing paper captures the key findings and recommendations of a study commissioned by the Joint Information Systems Committee on aspects of the strategic commitment of institutions to repository sustainability. This project, labelled EMBRACE (EMBedding Repositories And Consortial Enhancement), is aimed at enhancing the functionality,…

  4. 77 FR 58321 - National Oil and Hazardous Substances Pollution Contingency Plan; National Priorities List...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-09-20

    ... through http://www.regulations.gov or in hard copy at the site information repositories. Locations, contacts, phone numbers and viewing hours are: Regional Site Information Repository: U.S. EPA Record Center... Repository: New Hanover County Public Library 28401, 201 Chestnut Street, Wilmington, North Carolina 28401...

  5. Developing an Integrated Institutional Repository at Imperial College London

    ERIC Educational Resources Information Center

    Afshari, Fereshteh; Jones, Richard

    2007-01-01

    Purpose: This paper aims to demonstrate how a highly integrated approach to repository development and deployment can be beneficial in producing a successful archive. Design/methodology/approach: Imperial College London undertook a significant specifications process to gather and formalise requirements for its repository system. This was done…

  6. The Microbiology of Subsurface, Salt-Based Nuclear Waste Repositories: Using Microbial Ecology, Bioenergetics, and Projected Conditions to Help Predict Microbial Effects on Repository Performance

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Swanson, Juliet S.; Cherkouk, Andrea; Arnold, Thuro

    This report summarizes the potential role of microorganisms in salt-based nuclear waste repositories using available information on the microbial ecology of hypersaline environments, the bioenergetics of survival under high ionic strength conditions, and “repository microbiology” related studies. In areas where microbial activity is in question, there may be a need to shift the research focus toward feasibility studies rather than studies that generate actual input for performance assessments. In areas where activity is not necessary to affect performance (e.g., biocolloid transport), repository-relevant data should be generated. Both approaches will lend a realistic perspective to a safety case/performance scenario that willmore » most likely underscore the conservative value of that case.« less

  7. The Waste Isolation Pilot Plant transuranic waste repository: A sleeping beauty

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Eriksson, L.G.

    On May 13, 1998, crowning a 24-year United States Department of Energy effort, the US Environmental Protection Agency certified that the deep geological repository for safe disposal of long-lived, transuranic radioactive waste proposed by the DOE at the Waste Isolation Pilot Plant site in New Mexico complied with all applicable environmental radiation protection standards and compliance criteria. Pursuant to the applicable law, the WIPP Land Withdrawal Act of 1992, as amended in 1997, at the decision of the secretary of energy, the WIPP repository could open 30 calendar days after receiving the EPA certification. The secretary of energy announced Maymore » 13, 1998, that he intended to open the WIPP TRUW repository by June 14, 1998. However, at the end of 1998, the opening of the WIPP TRUW repository remains hostage to time-consuming, hazardous-waste-permitting procedures by the state of New Mexico Environment Department and two legal actions. Based on the EPA-verified high safety and the demonstrated risk reduction to both current and future generations offered by the WIPP TRUW repository, it is concluded that the WIPP TRUW repository is a sleeping beauty that will awake, perhaps in stages, and begin its important mission in 1999.« less

  8. Using Linked Open Data and Semantic Integration to Search Across Geoscience Repositories

    NASA Astrophysics Data System (ADS)

    Mickle, A.; Raymond, L. M.; Shepherd, A.; Arko, R. A.; Carbotte, S. M.; Chandler, C. L.; Cheatham, M.; Fils, D.; Hitzler, P.; Janowicz, K.; Jones, M.; Krisnadhi, A.; Lehnert, K. A.; Narock, T.; Schildhauer, M.; Wiebe, P. H.

    2014-12-01

    The MBLWHOI Library is a partner in the OceanLink project, an NSF EarthCube Building Block, applying semantic technologies to enable knowledge discovery, sharing and integration. OceanLink is testing ontology design patterns that link together: two data repositories, Rolling Deck to Repository (R2R), Biological and Chemical Oceanography Data Management Office (BCO-DMO); the MBLWHOI Library Institutional Repository (IR) Woods Hole Open Access Server (WHOAS); National Science Foundation (NSF) funded awards; and American Geophysical Union (AGU) conference presentations. The Library is collaborating with scientific users, data managers, DSpace engineers, experts in ontology design patterns, and user interface developers to make WHOAS, a DSpace repository, linked open data enabled. The goal is to allow searching across repositories without any of the information providers having to change how they manage their collections. The tools developed for DSpace will be made available to the community of users. There are 257 registered DSpace repositories in the United Stated and over 1700 worldwide. Outcomes include: Integration of DSpace with OpenRDF Sesame triple store to provide SPARQL endpoint for the storage and query of RDF representation of DSpace resources, Mapping of DSpace resources to OceanLink ontology, and DSpace "data" add on to provide resolvable linked open data representation of DSpace resources.

  9. Digital Repositories and the Question of Data Usefulness

    NASA Astrophysics Data System (ADS)

    Hughes, J. S.; Downs, R. R.

    2017-12-01

    The advent of ISO standards for trustworthy long-term digital repositories provides both a set of principles to develop long-term data repositories and the instruments to assess them for trustworthiness. Such mandatory high-level requirements are broad enough to be achievable, to some extent, by many scientific data centers, archives, and other repositories. But the requirement that the data be useful in the future, the requirement that is usually considered to be most relevant to the value of the repository for its user communities, largely remains subject to various interpretations and misunderstanding. However, current and future users will be relying on repositories to preserve and disseminate the data and information needed to discover, understand, and utilize these resources to support their research, learning, and decision-making objectives. Therefore, further study is needed to determine the approaches that can be adopted by repositories to make data useful to future communities of users. This presentation will describe approaches for enabling scientific data and related information, such as software, to be useful for current and potential future user communities and will present the methodology chosen to make one science discipline's data useful for both current and future users. The method uses an ontology-based information model to define and capture the information necessary to make the data useful for contemporary and future users.

  10. US/German Collaboration in Salt Repository Research, Design and Operation - 13243

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Steininger, Walter; Hansen, Frank; Biurrun, Enrique

    2013-07-01

    Recent developments in the US and Germany [1-3] have precipitated renewed efforts in salt repository investigations and related studies. Both the German rock salt repository activities and the US waste management programs currently face challenges that may adversely affect their respective current and future state-of-the-art core capabilities in rock salt repository science and technology. The research agenda being pursued by our respective countries leverages collective efforts for the benefit of both programs. The topics addressed by the US/German salt repository collaborations align well with the findings and recommendations summarized in the January 2012 US Blue Ribbon Commission on America's Nuclearmore » Future (BRC) report [4] and are consistent with the aspirations of the key topics of the Strategic Research Agenda of the Implementing Geological Disposal of Radioactive Waste Technology Platform (IGD-TP) [5]. Against this background, a revival of joint efforts in salt repository investigations after some years of hibernation has been undertaken to leverage collective efforts in salt repository research, design, operations, and related issues for the benefit of respective programs and to form a basis for providing an attractive, cost-effective insurance against the premature loss of virtually irreplaceable scientific expertise and institutional memory. (authors)« less

  11. Guidelines for quality assurance and quality control of fish taxonomic data collected as part of the National Water-Quality Assessment Program

    USGS Publications Warehouse

    Walsh, Stephen Joseph; Meador, Michael R.

    1998-01-01

    Fish community structure is characterized by the U.S. Geological Survey's National Water-Quality Assessment (NAWQA) Program as part of a perennial, multidisciplinary approach to evaluating the physical, chemical, and biological conditions of the Nation's water resources. The objective of quality assurance and quality control of fish taxonomic data that are collected as part of the NAWQA Program is to establish uniform guidelines and protocols for the identification, processing, and archiving of fish specimens to ensure that accurate and reliable data are collected. Study unit biologists, collaborating with regional biologists and fish taxonomic specialists, prepare a pre-sampling study plan that includes a preliminary faunal list and identification of an ichthyological curation center for receiving preserved fish specimens. Problematic taxonomic issues and protected taxa also are identified in the study plan, and collecting permits are obtained in advance of sampling activities. Taxonomic specialists are selected to identify fish specimens in the field and to assist in determining what fish specimens should be sacrificed, fixed, and preserved for laboratory identification, independent taxonomic verification, and long-term storage in reference or voucher collections. Quantitative and qualitative sampling of fishes follows standard methods previously established for the NAWQA Program. Common ichthyological techniques are used to process samples in the field and prepare fish specimens to be returned to the laboratory or sent to an institutional repository. Taxonomic identifications are reported by using a standardized list of scientific names that provides nomenclatural consistency and uniformity across study units.

  12. Characterize Framework for Igneous Activity at Yucca Mountain, Nevada

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    F. Perry; B. Youngs

    2000-11-06

    The purpose of this Analysis/Model (AMR) report is twofold. (1) The first is to present a conceptual framework of igneous activity in the Yucca Mountain region (YMR) consistent with the volcanic and tectonic history of this region and the assessment of this history by experts who participated in the Probabilistic Volcanic Hazard Analysis (PVHA) (CRWMS M&O 1996). Conceptual models presented in the PVHA are summarized and extended in areas in which new information has been presented. Alternative conceptual models are discussed as well as their impact on probability models. The relationship between volcanic source zones defined in the PVHA andmore » structural features of the YMR are described based on discussions in the PVHA and studies presented since the PVHA. (2) The second purpose of the AMR is to present probability calculations based on PVHA outputs. Probability distributions are presented for the length and orientation of volcanic dikes within the repository footprint and for the number of eruptive centers located within the repository footprint (conditional on the dike intersecting the repository). The probability of intersection of a basaltic dike within the repository footprint was calculated in the AMR ''Characterize Framework for Igneous Activity at Yucca Mountain, Nevada'' (CRWMS M&O 2000g) based on the repository footprint known as the Enhanced Design Alternative [EDA II, Design B (CRWMS M&O 1999a; Wilkins and Heath 1999)]. Then, the ''Site Recommendation Design Baseline'' (CRWMS M&O 2000a) initiated a change in the repository design, which is described in the ''Site Recommendation Subsurface Layout'' (CRWMS M&O 2000b). Consequently, the probability of intersection of a basaltic dike within the repository footprint has also been calculated for the current repository footprint, which is called the 70,000 Metric Tons of Uranium (MTU) No-Backfill Layout (CRWMS M&O 2000b). The calculations for both footprints are presented in this AMR. In addition, the probability of an eruptive center(s) forming within the repository footprint is calculated and presented in this AMR for both repository footprint designs. This latter type of calculation was not included in the PVHA.« less

  13. A University Library Creates a Digital Repository for Documenting and Disseminating Community Engagement

    ERIC Educational Resources Information Center

    Miller, William A.; Billings, Marilyn

    2012-01-01

    Digital repositories are new tools for documenting the accumulated scholarly work produced at academic institutions and disseminating that material broadly via the internet. Digital repositories support all file types and can be adapted to meet the custom design specifications of individual institutions. A section for community engagement…

  14. Using OAI-PMH and METS for Exporting Metadata and Digital Objects between Repositories

    ERIC Educational Resources Information Center

    Bell, Jonathan; Lewis, Stuart

    2006-01-01

    Purpose: To examine the relationship between deposit of electronic theses in institutional and archival repositories. Specifically the paper considers the automated export of theses for deposit in the archival repository in continuation of the existing arrangement in Wales for paper-based theses. Design/methodology/approach: The paper presents a…

  15. 77 FR 3745 - Establishment of a One-Year Retention Period for Patent-Related Papers That Have Been Scanned...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-01-25

    ... File Wrapper System or the Supplemental Complex Repository for Examiners AGENCY: United States Patent... (IFW) or the Supplemental Complex Repository for Examiners (SCORE). The USPTO has considered the... Supplemental Complex Repository for Examiners, 76 FR 53667 (August 29, 2011), 1370 Off. Gaz. Pat. Office 211...

  16. The World Sugarcane and Related Grasses Collection at USDA/ARS Genebank Repository in Miami, Florida, USA

    USDA-ARS?s Scientific Manuscript database

    In early 1980’s the USDA-ARS established the National Plant Germplasm System (NPGS) a network of gene banks to preserve genetic resources of importance to National and International agriculture. The National Clonal Germplasm Repository (NCGR) in Miami, Florida is one of these repositories. This repo...

  17. 10 CFR 960.5-2-1 - Population density and distribution.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... SITES FOR A NUCLEAR WASTE REPOSITORY Preclosure Guidelines Preclosure Radiological Safety § 960.5-2-1... repository operation and closure, (1) the expected average radiation dose to members of the public within any...) Disqualifying conditions. A site shall be disqualified if— (1) Any surface facility of a repository would be...

  18. 75 FR 54642 - Privacy Act of 1974; United States Citizenship and Immigration Services-012 Citizenship and...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-09-08

    ... Repository System of Records AGENCY: Privacy Office, DHS. ACTION: Notice of Privacy Act system of records... Immigration Services 012 Citizenship and Immigration Data Repository System of Records.'' Citizenship and Immigration Data Repository is a mirror copy of USCIS's major immigrant and non-immigrant benefits databases...

  19. 75 FR 66110 - Guidelines for Use of Stored Specimens and Access to Ancillary Data and Proposed Cost Schedule...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-27

    ... repository of datasets from completed studies, biospecimens, and ancillary data. The Division intends to make... Sharing Policy. The Division has established an internal committee, the Biospecimen Repository Access and Data Sharing Committee (BRADSC), to oversee the repository access and data sharing program. The purpose...

  20. 75 FR 73095 - Privacy Act of 1974; Report of New System of Records

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-29

    ... Repository'' System No. 09-70-0587. The final rule for the Medicare and Medicaid EHR Incentive Program... primary purpose of this system, called the National Level Repository or NLR, is to collect, maintain, and... Maintenance of Data in the System The National Level Repository (NLR) contains information on eligible...

  1. 10 CFR 960.3-2-1 - Site screening for potentially acceptable sites.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... POTENTIAL SITES FOR A NUCLEAR WASTE REPOSITORY Implementation Guidelines § 960.3-2-1 Site screening for... first repository, the process shall begin with site-screening activities that consider large land masses... repositories, the Secretary shall first identify the State within which the site is located in a decision-basis...

  2. Institutional Repositories, Open Access, and Scholarly Communication: A Study of Conflicting Paradigms

    ERIC Educational Resources Information Center

    Cullen, Rowena; Chawner, Brenda

    2011-01-01

    The Open Access movement of the past decade, and institutional repositories developed by universities and academic libraries as a part of that movement, have openly challenged the traditional scholarly communication system. This article examines the growth of repositories around the world, and summarizes a growing body of evidence of the response…

  3. 77 FR 22632 - Privacy Act of 1974; System of Records

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-16

    ...--Repository (SCIDO-R)-VA'' (108VA11S) as set forth in the Federal Register 74 FR 11185-11186 dated March 16.... SUPPLEMENTARY INFORMATION: The Spinal Cord Injury and Disorders Outcomes--Repository (SCIDO-R) provides a registry of veterans with spinal cord injury and disorders (SCI&D). This repository contains pertinent...

  4. 75 FR 8742 - Notice of Inventory Completion: Stephen F. Austin State University, Nacogdoches, TX

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-02-25

    ... repository of the anthropology lab some time after 1975. No known individual was identified. No associated... the repository of the Stephen F. Austin State University anthropology lab. No known individual was.... The human remains are located in the repository of the Stephen F. Austin State University anthropology...

  5. Neural network-based retrieval from software reuse repositories

    NASA Technical Reports Server (NTRS)

    Eichmann, David A.; Srinivas, Kankanahalli

    1992-01-01

    A significant hurdle confronts the software reuser attempting to select candidate components from a software repository - discriminating between those components without resorting to inspection of the implementation(s). We outline an approach to this problem based upon neural networks which avoids requiring the repository administrators to define a conceptual closeness graph for the classification vocabulary.

  6. Digital Libraries and Repositories in India: An Evaluative Study

    ERIC Educational Resources Information Center

    Mittal, Rekha; Mahesh, G.

    2008-01-01

    Purpose: The purpose of this research is to identify and evaluate the collections within digital libraries and repositories in India available in the public domain. Design/methodology/approach: The digital libraries and repositories were identified through a study of the literature, as well as internet searching and browsing. The resulting digital…

  7. 10 CFR 960.3-2-2-2 - Selection of sites within geohydrologic settings.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... OF POTENTIAL SITES FOR A NUCLEAR WASTE REPOSITORY Implementation Guidelines § 960.3-2-2-2 Selection... nominated as suitable for characterization. For purposes of the second and subsequent repositories, due... suitable for the development of a repository under the qualifying condition of each guideline specified in...

  8. 75 FR 81371 - Privacy Act of 1974: Implementation of Exemptions; Department of Homeland Security/United States...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-12-28

    ... Citizenship and Immigration Services- 012 Citizenship and Immigration Data Repository System of Records AGENCY... Immigration Data Repository System of Records'' from certain provisions of the Privacy Act. Specifically, the... Immigration Services-012 Citizenship and Immigration Data Repository System of Records'' from one or more...

  9. Creating Complex Repository Collections, Such as Journals, with Manakin

    ERIC Educational Resources Information Center

    Koenig, Jack; Mikeal, Adam

    2010-01-01

    Purpose: The purpose of this paper is to report on a devised method of collection organisation within a DSpace repository using a Manakin theme and descriptive metadata. Design/methodology/approach: Using a Manakin theme, a user interface for a repository collection containing the contents of a serial was created to divide the collection into…

  10. History, Context, and Policies of a Learning Object Repository

    ERIC Educational Resources Information Center

    Simpson, Steven Marshall

    2016-01-01

    Learning object repositories, a form of digital libraries, are robust systems that provide educators new ways to search for educational resources, collaborate with peers, and provide instruction to students in unique and varied ways. This study examines a learning object repository created by a large suburban school district to increase teaching…

  11. 78 FR 22350 - Self-Regulatory Organizations; ICE Clear Credit LLC; Notice of Filing and Order Granting...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-04-15

    ... governing security-based swap data repositories and security-based swap reporting. See, e.g., Pub. L. No... Depository Trust & Clearing Corporation (``DTCC''), in conjunction with DTCC Data Repository (U.S.) LLC.\\40... 75208 (Dec. 2, 2010); Security-Based Swap Data Repository Registration, Duties, and Core Principles...

  12. 75 FR 61373 - Proposed Flood Elevation Determinations

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-05

    ... located at the community map repository (see below) for exact locations of all BFEs to be changed. Send... located at the community map repository (see below) for exact locations of all BFEs to be changed. Send.... Please refer to the revised Flood Insurance Rate Map located at the community map repository (see below...

  13. 76 FR 61649 - Proposed Flood Elevation Determinations

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-10-05

    ... Insurance Rate Map located at the community map repository (see below) for exact locations of all BFEs to be... Insurance Rate Map located at the community map repository (see below) for exact locations of all BFEs to be... revised Flood Insurance Rate Map located at the community map repository (see below) for exact locations...

  14. Three-dimensional thermal analysis of a high-level waste repository

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Altenbach, T.J.

    1979-04-01

    The analysis used the TRUMP computer code to evaluate the thermal fields for six repository scenarios that studied the effects of room ventilation, room backfill, and repository thermal diffusivity. The results for selected nodes are presented as plots showing the effect of temperature as a function of time. 15 figures, 6 tables.

  15. Preliminary safety analysis of the Baita Bihor radioactive waste repository, Romania

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Little, Richard; Bond, Alex; Watson, Sarah

    2007-07-01

    A project funded under the European Commission's Phare Programme 2002 has undertaken an in-depth analysis of the operational and post-closure safety of the Baita Bihor repository. The repository has accepted low- and some intermediate-level radioactive waste from industry, medical establishments and research activities since 1985 and the current estimate is that disposals might continue for around another 20 to 35 years. The analysis of the operational and post-closure safety of the Baita Bihor repository was carried out in two iterations, with the second iteration resulting in reduced uncertainties, largely as a result taking into account new information on the hydrologymore » and hydrogeology of the area, collected as part of the project. Impacts were evaluated for the maximum potential inventory that might be available for disposal to Baita Bihor for a number of operational and postclosure scenarios and associated conceptual models. The results showed that calculated impacts were below the relevant regulatory criteria. In light of the assessment, a number of recommendations relating to repository operation, optimisation of repository engineering and waste disposals, and environmental monitoring were made. (authors)« less

  16. Repository Planning, Design, and Engineering: Part II-Equipment and Costing.

    PubMed

    Baird, Phillip M; Gunter, Elaine W

    2016-08-01

    Part II of this article discusses and provides guidance on the equipment and systems necessary to operate a repository. The various types of storage equipment and monitoring and support systems are presented in detail. While the material focuses on the large repository, the requirements for a small-scale startup are also presented. Cost estimates and a cost model for establishing a repository are presented. The cost model presents an expected range of acquisition costs for the large capital items in developing a repository. A range of 5,000-7,000 ft(2) constructed has been assumed, with 50 frozen storage units, to reflect a successful operation with growth potential. No design or engineering costs, permit or regulatory costs, or smaller items such as the computers, software, furniture, phones, and barcode readers required for operations have been included.

  17. An open repositories network development for medical teaching resources.

    PubMed

    Soula, Gérard; Darmoni, Stefan; Le Beux, Pierre; Renard, Jean-Marie; Dahamna, Badisse; Fieschi, Marius

    2010-01-01

    The lack of interoperability between repositories of heterogeneous and geographically widespread data is an obstacle to the diffusion, sharing and reutilization of those data. We present the development of an open repositories network taking into account both the syntactic and semantic interoperability of the different repositories and based on international standards in this field. The network is used by the medical community in France for the diffusion and sharing of digital teaching resources. The syntactic interoperability of the repositories is managed using the OAI-PMH protocol for the exchange of metadata describing the resources. Semantic interoperability is based, on one hand, on the LOM standard for the description of resources and on MESH for the indexing of the latter and, on the other hand, on semantic interoperability management designed to optimize compliance with standards and the quality of the metadata.

  18. High Integrity Can Design Interfaces

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Shaber, E.L.

    1998-08-01

    The National Spent Nuclear Fuel Program is chartered with facilitating the disposition of DOE-owned spent nuclear fuel to allow disposal at a geologic repository. This is done through coordination with the repository program and by assisting DOE Site owners of SNF with needed information, standardized requirements, packaging approaches, etc. The High Integrity Can (HIC) will be manufactured to provide a substitute or barrier enhancement for normal fuel geometry and cladding. The can would be nested inside the DOE standardized canister which is designed to interface with the repository waste package. The HIC approach may provide the following benefits over typicalmore » canning approaches for DOE SNF. (a) It allows ready calculation and management of criticality issues for miscellaneous. (b) It segments and further isolates damaged or otherwise problem materials from normal SNF in the repository package. (c) It provides a very long term corrosion barrier. (d) It provides an extra internal pressure barrier for particulates, gaseous fission products, hydrogen, and water vapor. (e) It delays any potential release of fission products to the repository environment. (f) It maintains an additional level of fuel geometry control during design basis accidents, rock-fall, and seismic events. (g) When seal welded, it could provide the additional containment required for shipments involving plutonium content in excess of 20 Ci. (10 CFR 71.63.b) if integrated with an appropriate cask design. Long term corrosion protection is central to the HIC concept. The material selected for the HIC (Hastelloy C-22) has undergone extensive testing for repository service. The most severe theoretical interactions between iron, repository water containing chlorides and other repository construction materials have been tested. These expected chemical species have not been shown capable of corroding the selected HIC material. Therefore, the HIC should provide a significant barrier to DOE SNF dispersal long after most commercial SNF has degraded and begun moving into the repository environment.« less

  19. Implementing and Sustaining Data Lifecycle best Practices: a Framework for Researchers and Repositories

    NASA Astrophysics Data System (ADS)

    Stall, S.

    2016-02-01

    Emerging data management mandates in conjunction with cross-domain international interoperability are posing new challenges for researchers and repositories. Domain repositories are serving in this critical, growing role monitoring and leading data management standards and capability within their own repository and working on mappings between repositories internationally. Leading research institutions and companies will also be important as they develop and expand data curation efforts. This landscape poses a number of challenges for developing and ensuring the use of best practices in curating research data, enabling discovery, elevating quality across diverse repositories, and helping researchers collect and organize it through the full data life cycle. This multidimensional challenge will continue to grow in complexity. The American Geophysical Union (AGU) is developing two programs to help researchers and data repositories develop and elevate best practices and address these challenges. The goal is to provide tools for the researchers and repositories, whether domain, institutional, or other, that improve performance throughout the data lifecycle across the Earth and space science community. For scientists and researchers, AGU is developing courses around handling data that can lead toward a certification in geoscience data management. Course materials will cover metadata management and collection, data analysis, integration of data, and data presentation. The course topics are being finalized by the advisory board with the first one planned to be available later this year. AGU is also developing a program aimed at helping data repositories, large and small, domain-specific to general, assess and improve data management practices. AGU has partnered with the CMMI® Institute to adapt their Data Management Maturity (DMM)SM framework within the Earth and space sciences. A data management assessment using the DMMSM involves identifying accomplishments and weaknesses compared to leading practices for data management. Recommendations can help improve quality and consistency across the community that will facilitate reuse in the data lifecycle. Through governance, quality, and architecture process areas the assessment can measure the ability for data to be discoverable and interoperable.

  20. The Challenges of Releasing Human Data for Analysis

    NASA Technical Reports Server (NTRS)

    Fitts, Mary; Van Baalen, Mary; Johnson-Throop, Kathy; Lee, Lesley; Havelka, Jacque; Wear, Mary; Thomas, Diedre M.

    2011-01-01

    The NASA Johnson Space Center s (NASA JSC) Committee for the Protection of Human Subjects (CPHS) recently approved the formation of two human data repositories: the Lifetime Surveillance of Astronaut Health Repository (LSAH-R) for clinical data and the Life Sciences Data Archive Repository (LSDA-R) for research data. The establishment of these repositories forms the foundation for the release of data and information beyond the scope for which the data was originally collected. The release of clinical and research data and information is primarily managed by two NASA groups: the Evidence Base Working Group (EBWG), consisting of members of both repositories, and the LSAH Policy Board. The goal of unifying these repositories and their processes is to provide a mutually supportive approach to handling medical and research data, to enhance the use of medical and research data to reduce risk, and to promote the understanding of space physiology, countermeasures and other mitigation strategies. Over the past year, both repositories have received over 100 data and information requests from a wide variety of requesters. The disposition of these requests has highlighted the challenges faced when attempting to make data collected on a unique set of subjects available beyond the original intent for which the data were collected. As the EBWG works through each request, many considerations must be factored into account when deciding what data can be shared and how - from the Privacy Act of 1974 and the Health Insurance Portability and Accountability Act (HIPAA), to NASA s Health Information Management System (10HIMS) and Human Experimental and Research Data Records (10HERD) access requirements. Additional considerations include the presence of the data in the repositories and vetting requesters for legitimacy of their use of the data. Additionally, fair access must be ensured for intramural, as well as extramural investigators. All of this must be considered in the formulation of the charters, policies and workflows for the human data repositories at NASA.

  1. Sharing individual participant data from clinical trials: an opinion survey regarding the establishment of a central repository.

    PubMed

    Tudur Smith, Catrin; Dwan, Kerry; Altman, Douglas G; Clarke, Mike; Riley, Richard; Williamson, Paula R

    2014-01-01

    Calls have been made for increased access to individual participant data (IPD) from clinical trials, to ensure that complete evidence is available. However, despite the obvious benefits, progress towards this is frustratingly slow. In the meantime, many systematic reviews have already collected IPD from clinical trials. We propose that a central repository for these IPD should be established to ensure that these datasets are safeguarded and made available for use by others, building on the strengths and advantages of the collaborative groups that have been brought together in developing the datasets. Evaluate the level of support, and identify major issues, for establishing a central repository of IPD. On-line survey with email reminders. 71 reviewers affiliated with the Cochrane Collaboration's IPD Meta-analysis Methods Group were invited to participate. 30 (42%) invitees responded: 28 (93%) had been involved in an IPD review and 24 (80%) had been involved in a randomised trial. 25 (83%) agreed that a central repository was a good idea and 25 (83%) agreed that they would provide their IPD for central storage. Several benefits of a central repository were noted: safeguarding and standardisation of data, increased efficiency of IPD meta-analyses, knowledge advancement, and facilitating future clinical, and methodological research. The main concerns were gaining permission from trial data owners, uncertainty about the purpose of the repository, potential resource implications, and increased workload for IPD reviewers. Restricted access requiring approval, data security, anonymisation of data, and oversight committees were highlighted as issues under governance of the repository. There is support in this community of IPD reviewers, many of whom are also involved in clinical trials, for storing IPD in a central repository. Results from this survey are informing further work on developing a repository of IPD which is currently underway by our group.

  2. Revision history aware repositories of computational models of biological systems.

    PubMed

    Miller, Andrew K; Yu, Tommy; Britten, Randall; Cooling, Mike T; Lawson, James; Cowan, Dougal; Garny, Alan; Halstead, Matt D B; Hunter, Peter J; Nickerson, David P; Nunns, Geo; Wimalaratne, Sarala M; Nielsen, Poul M F

    2011-01-14

    Building repositories of computational models of biological systems ensures that published models are available for both education and further research, and can provide a source of smaller, previously verified models to integrate into a larger model. One problem with earlier repositories has been the limitations in facilities to record the revision history of models. Often, these facilities are limited to a linear series of versions which were deposited in the repository. This is problematic for several reasons. Firstly, there are many instances in the history of biological systems modelling where an 'ancestral' model is modified by different groups to create many different models. With a linear series of versions, if the changes made to one model are merged into another model, the merge appears as a single item in the history. This hides useful revision history information, and also makes further merges much more difficult, as there is no record of which changes have or have not already been merged. In addition, a long series of individual changes made outside of the repository are also all merged into a single revision when they are put back into the repository, making it difficult to separate out individual changes. Furthermore, many earlier repositories only retain the revision history of individual files, rather than of a group of files. This is an important limitation to overcome, because some types of models, such as CellML 1.1 models, can be developed as a collection of modules, each in a separate file. The need for revision history is widely recognised for computer software, and a lot of work has gone into developing version control systems and distributed version control systems (DVCSs) for tracking the revision history. However, to date, there has been no published research on how DVCSs can be applied to repositories of computational models of biological systems. We have extended the Physiome Model Repository software to be fully revision history aware, by building it on top of Mercurial, an existing DVCS. We have demonstrated the utility of this approach, when used in conjunction with the model composition facilities in CellML, to build and understand more complex models. We have also demonstrated the ability of the repository software to present version history to casual users over the web, and to highlight specific versions which are likely to be useful to users. Providing facilities for maintaining and using revision history information is an important part of building a useful repository of computational models, as this information is useful both for understanding the source of and justification for parts of a model, and to facilitate automated processes such as merges. The availability of fully revision history aware repositories, and associated tools, will therefore be of significant benefit to the community.

  3. Task-Based Navigation of a Taxonomy Interface to a Digital Repository

    ERIC Educational Resources Information Center

    Khoo, Christopher S. G.; Wang, Zhonghong; Chaudhry, Abdus Sattar

    2012-01-01

    Introduction: This is a study of hierarchical navigation; how users browse a taxonomy-based interface to an organizational repository to locate information resources. The study is part of a project to develop a taxonomy for an library and information science department to organize resources and support user browsing in a digital repository.…

  4. 17 CFR 43.3 - Method and timing for real-time public reporting.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... § 43.5. (3) Prohibitions on disclosure of data. (i) If there is a registered swap data repository for... disclosure is made no earlier than the transmittal of such data to a registered swap data repository for... such data by a registered swap data repository unless: (A) Such disclosure is made no earlier than the...

  5. 17 CFR 45.10 - Reporting to a single swap data repository.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... the swap data repository to which the first report of required swap creation data is made pursuant to... designated contract market that reports required swap creation data as required by § 45.3 shall report all... of the swap data repository to which required swap creation data is reported by the swap execution...

  6. 17 CFR 45.10 - Reporting to a single swap data repository.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ..., which shall be the swap data repository to which the first report of required swap creation data is made... designated contract market that reports required swap creation data as required by § 45.3 shall report all... of the swap data repository to which required swap creation data is reported by the swap execution...

  7. 17 CFR 45.10 - Reporting to a single swap data repository.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... the swap data repository to which the first report of required swap creation data is made pursuant to... designated contract market that reports required swap creation data as required by § 45.3 shall report all... of the swap data repository to which required swap creation data is reported by the swap execution...

  8. Planting Seeds for a Successful Institutional Repository: Role of the Archivist as Manager, Designer, and Policymaker

    ERIC Educational Resources Information Center

    Watterworth, Melissa

    2009-01-01

    Recent surveys indicate that many colleges and universities have reached a pivotal moment in assessing the function and future development of their institutional repositories. Other surveys convey that archivists are participating in the development and implementation of institutional repositories at a variety of levels and have contributed to the…

  9. 75 FR 78892 - Reporting Certain Post-Enactment Swap Transactions

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-12-17

    ...)--to a registered swap data repository (``SDR'') or to the Commission. Each category of data is subject... expired by that date. \\5\\ The term ``swap data repository'' is defined in Section 1a(48) of the CEA to... date of the enactment of this subsection shall be reported to a registered swap data repository or the...

  10. 76 FR 53667 - Establishing a One-Year Retention Period for Patent-Related Papers That Have Been Scanned Into...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-08-29

    ... System or the Supplemental Complex Repository for Examiners AGENCY: United States Patent and Trademark... been scanned into the Image File Wrapper system (IFW) or the Supplemental Complex Repository for..., the USPTO had fully deployed SCORE, a data repository system designed to augment IFW with the capture...

  11. 75 FR 70025 - Notice of Inventory Completion: U.S. Department of the Interior, Bureau of Reclamation, Pacific...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-16

    ... Repository, Nespelem, WA AGENCY: National Park Service, Interior. ACTION: Notice. Notice is hereby given in... Repository, Nespelem, WA. The human remains were removed from Grant County, WA. This notice is published as... Washington State University. In 2006, they were transferred to the Colville Tribal Repository for curation...

  12. Science is the first step to siting nuclear waste repositories

    USGS Publications Warehouse

    Neuzil, Christopher E.

    2014-01-01

    As Shaw [2014] notes, U.S. research on shale as a repository host was halted before expending anything close to the effort devoted to studying crystalline rock, salt, and - most notably - tuff at Yucca Mountain. The new political reality regarding Yucca Mountain may allow reconsideration of the decision to abandon research on shale as a repository host.

  13. The Situation of Open Access Institutional Repositories in Spain: 2009 Report

    ERIC Educational Resources Information Center

    Melero, Remedios; Abadal, Ernest; Abad, Francisca; Rodriguez-Gairin, Josep Manel

    2009-01-01

    Introduction: The DRIVER I project drew up a detailed report of European repositories based on data gathered in a survey in which Spain's participation was very low. This created a highly distorted image of the implementation of repositories in Spain. This study aims to analyse the current state of Spanish open-access institutional repositories…

  14. The Efficacy of Institutional Repositories: Reflections on the Development of a Personalised Collection on UPSpace

    ERIC Educational Resources Information Center

    Olivier, Elsabe

    2007-01-01

    There is much speculation that the development of institutional repositories will impact on or even change the traditional scholarly communication process. The purpose of this conversation is to introduce the reader to the use of and response to institutional repositories which were initiated by the Open Access Initiative. The concept of…

  15. Repository Collection Policies: Is a Liberal and Inclusive Policy Helpful or Harmful?

    ERIC Educational Resources Information Center

    Bankier, Jean-Gabriel; Smith, Courtney

    2010-01-01

    Institutional repositories have been established by most university libraries but their level of success has varied. Determining what belongs in such repositories has been the subject of some discussion but research would suggest that a broader rather than narrower compass is a positive approach to adopt. By seeking out a variety of content types,…

  16. 10 CFR 960.3-2-3 - Recommendation of sites for characterization.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... POTENTIAL SITES FOR A NUCLEAR WASTE REPOSITORY Implementation Guidelines § 960.3-2-3 Recommendation of sites... characterization for the selection of the first repository, the Secretary shall recommend in writing to the..., and, after the first repository, consideration of regionality in §§ 960.3-1-1, 960.3-1-2, and 960.3-1...

  17. A Comparison of Subject and Institutional Repositories in Self-Archiving Practices

    ERIC Educational Resources Information Center

    Xia, Jingfeng

    2008-01-01

    The disciplinary culture theory presumes that if a scholar has been familiar with self-archiving through an existing subject-based repository, this scholar will be more enthusiastic about contributing his/her research to an institutional repository than one who has not had the experience. To test the theory, this article examines self-archiving…

  18. 75 FR 62435 - Agency Information Collection Activities: Submission for the Office of Management and Budget (OMB...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-08

    ... Proposed Geologic Repository at Yucca Mountain, Nevada.'' 3. Current OMB approval number: 3150-0199. [[Page... potential high-level waste geologic repository site, or wishing to participate in a license application review for the potential geologic repository. 7. An estimate of the number of annual responses: 3. 8. The...

  19. 77 FR 70190 - Agency Information Collection Activities: Submission for the Office of Management and Budget (OMB...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-11-23

    ... Repositories.'' 3. Current OMB approval number: 3150-0127. 4. The form number if applicable: N/A. 5. How often... the NRC staff regarding review of a potential high-level radioactive waste geologic repository site, or wishing to participate in a license application review for a potential geologic repository (other...

  20. Collaborative Learning Utilizing a Domain-Based Shared Data Repository to Enhance Learning Outcomes

    ERIC Educational Resources Information Center

    Lubliner, David; Widmeyer, George; Deek, Fadi P.

    2009-01-01

    The objective of this study was to determine whether there was a quantifiable improvement in learning outcomes by integrating course materials in a 4-year baccalaureate program, utilizing a knowledge repository with a conceptual map that spans a discipline. Two new models were developed to provide the framework for this knowledge repository. A…

  1. My Three Wishes for Digital Repositories. Building Digital Libraries

    ERIC Educational Resources Information Center

    Huwe, Terence K.

    2005-01-01

    In this column on digital repository management, the author defines three areas within the sphere of digital repositories that need work. The first two pertain to information architecture, while the last one pertains to taking action. The author's first "wish" is for top-notch library Web sites that act as a gateway to any sphere of knowledge. He…

  2. Yucca Mountain Project Subsurface Facilities Design

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    A. Linden; R.S. Saunders; R.J. Boutin

    2002-11-19

    Four units of the Topopah Springs formation (volcanic tuff) are considered for the proposed repository: the upper lithophysal, the middle non-lithophysal, the lower lithophysal, and the lower non-lithophysal. Yucca Mountain was recently designated the site for a proposed repository to dispose of spent nuclear fuel and high-level radioactive waste. Work is proceeding to advance the design of subsurface facilities to accommodate emplacing waste packages in the proposed repository. This paper summarized recent progress in the design of subsurface layout of the proposed repository. The original Site Recommendation (SR) concept for the subsurface design located the repository largely within the lowermore » lithophysal zone (approximately 73%) of the Topopah The Site Recommendation characterized area suitable for emplacement consisted of the primary upper block, the lower block and the southern upper block extension. The primary upper block accommodated the mandated 70,000 metric tons of heavy metal (MTHM) at a 1.45 kW/m hear heat load. Based on further study of the Site Recommendation concept, the proposed repository siting area footprint was modified to make maximum use of available site characterization data, and thus, reduce uncertainties associated with performance assessment. As a result of this study, a modified repository footprint has been proposed and is presently being review for acceptance by the DOE. A panel design concept was developed to reduce overall costs and reduce the overall emplacement schedule. This concept provides flexibility to adjust the proposed repository subsurface layout with time, as it makes it unnecessary to ''commit'' to development of a large single panel at the earliest stages of construction. A description of the underground layout configuration and influencing factors that affect the layout configuration are discussed in the report.« less

  3. 3D numerical modelling of the thermal state of deep geological nuclear waste repositories

    NASA Astrophysics Data System (ADS)

    Butov, R. A.; Drobyshevsky, N. I.; Moiseenko, E. V.; Tokarev, Yu. N.

    2017-09-01

    One of the important aspects of the high-level radioactive waste (HLW) disposal in deep geological repositories is ensuring the integrity of the engineered barriers which is, among other phenomena, considerably influenced by the thermal loads. As the HLW produce significant amount of heat, the design of the repository should maintain the balance between the cost-effectiveness of the construction and the sufficiency of the safety margins, including those imposed on the thermal conditions of the barriers. The 3D finite-element computer code FENIA was developed as a tool for simulation of thermal processes in deep geological repositories. Further the models for mechanical phenomena and groundwater hydraulics will be added resulting in a fully coupled thermo-hydro-mechanical (THM) solution. The long-term simulations of the thermal state were performed for two possible layouts of the repository. One was based on the proposed project of Russian repository, and another features larger HLW amount within the same space. The obtained results describe the spatial and temporal evolution of the temperature filed inside the repository and in the surrounding rock for 3500 years. These results show that practically all generated heat was ultimately absorbed by the host rock without any significant temperature increase. Still in the short time span even in case of smaller amount of the HLW the temperature maximum exceeds 100 °C, and for larger amount of the HLW the local temperature remains above 100 °C for considerable time. Thus, the substantiation of the long-term stability of the repository would require an extensive study of the materials properties and behaviour in order to remove the excessive conservatism from the simulations and to reduce the uncertainty of the input data.

  4. Simulation of fluid flow and energy transport processes associated with high-level radioactive waste disposal in unsaturated alluvium

    USGS Publications Warehouse

    Pollock, David W.

    1986-01-01

    Many parts of the Great Basin have thick zones of unsaturated alluvium which might be suitable for disposing of high-level radioactive wastes. A mathematical model accounting for the coupled transport of energy, water (vapor and liquid), and dry air was used to analyze one-dimensional, vertical transport above and below an areally extensive repository. Numerical simulations were conducted for a hypothetical repository containing spent nuclear fuel and located 100 m below land surface. Initial steady state downward water fluxes of zero (hydrostatic) and 0.0003 m yr−1were considered in an attempt to bracket the likely range in natural water flux. Predicted temperatures within the repository peaked after approximately 50 years and declined slowly thereafter in response to the decreasing intensity of the radioactive heat source. The alluvium near the repository experienced a cycle of drying and rewetting in both cases. The extent of the dry zone was strongly controlled by the mobility of liquid water near the repository under natural conditions. In the case of initial hydrostatic conditions, the dry zone extended approximately 10 m above and 15 m below the repository. For the case of a natural flux of 0.0003 m yr−1 the relative permeability of water near the repository was initially more than 30 times the value under hydrostatic conditions, consequently the dry zone extended only about 2 m above and 5 m below the repository. In both cases a significant perturbation in liquid saturation levels persisted for several hundred years. This analysis illustrates the extreme sensitivity of model predictions to initial conditions and parameters, such as relative permeability and moisture characteristic curves, that are often poorly known.

  5. Audit of a Scientific Data Center for Certification as a Trustworthy Digital Repository: A Case Study

    NASA Astrophysics Data System (ADS)

    Downs, R. R.; Chen, R. S.

    2011-12-01

    Services that preserve and enable future access to scientific data are necessary to ensure that the data that are being collected today will be available for use by future generations of scientists. Many data centers, archives, and other digital repositories are working to improve their ability to serve as long-term stewards of scientific data. Trust in sustainable data management and preservation capabilities of digital repositories can influence decisions to use these services to deposit or obtain scientific data. Building on the Open Archival Information System (OAIS) Reference Model developed by the Consultative Committee for Space Data Systems (CCSDS) and adopted by the International Organization for Standardization as ISO 14721:2003, new standards are being developed to improve long-term data management processes and documentation. The Draft Information Standard ISO/DIS 16363, "Space data and information transfer systems - Audit and certification of trustworthy digital repositories" offers the potential to evaluate digital repositories objectively in terms of their trustworthiness as long-term stewards of digital resources. In conjunction with this, the CCSDS and ISO are developing another draft standard for the auditing and certification process, ISO/DIS 16919, "Space data and information transfer systems - Requirements for bodies providing audit and certification of candidate trustworthy digital repositories". Six test audits were conducted of scientific data centers and archives in Europe and the United States to test the use of these draft standards and identify potential improvements for the standards and for the participating digital repositories. We present a case study of the test audit conducted on the NASA Socioeconomic Data and Applications Center (SEDAC) and describe the preparation, the audit process, recommendations received, and next steps to obtain certification as a trustworthy digital repository, after approval of the ISO/DIS standards.

  6. Uncertainty and sensitivity analysis for two-phase flow in the vicinity of the repository in the 1996 performance assessment for the Waste Isolation Pilot Plant: Undisturbed conditions

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    HELTON,JON CRAIG; BEAN,J.E.; ECONOMY,K.

    2000-05-19

    Uncertainty and sensitivity analysis results obtained in the 1996 performance assessment for the Waste Isolation Pilot Plant are presented for two-phase flow the vicinity of the repository under undisturbed conditions. Techniques based on Latin hypercube sampling, examination of scatterplots, stepwise regression analysis, partial correlation analysis and rank transformation are used to investigate brine inflow, gas generation repository pressure, brine saturation and brine and gas outflow. Of the variables under study, repository pressure is potentially the most important due to its influence on spallings and direct brine releases, with the uncertainty in its value being dominated by the extent to whichmore » the microbial degradation of cellulose takes place, the rate at which the corrosion of steel takes place, and the amount of brine that drains from the surrounding disturbed rock zone into the repository.« less

  7. Managing the nation`s nuclear waste. Site descriptions: Cypress Creek, Davis Canyon, Deaf Smith, Hanford Reference, Lavender Canyon, Richton Dome, Swisher, Vacherie Dome, and Yucca Mountain

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    NONE

    1985-12-31

    In 1982, the Congress enacted the Nuclear Waste Policy Act (Public Law 97-425), which established a comprehensive national program directed toward siting, constructing, and operating geologic repositories for the permanent disposal of high-level radioactive waste. In February 1983, the United States Department of Energy (DOE) identified the nine referenced repository locations as potentially acceptable sites for a mined geologic repository. These sites have been evaluated in accordance with the DOE`s General Guidelines for the Recommendation of Sites for Nuclear Waste Repositories. The DOE findings and determinations are based on the evaluations contained in the draft Environmental Assessments (EA). A finalmore » EA will be prepared after considering the comments received on the draft EA. The purpose of this document is to provide the public with specific site information on each potential repository location.« less

  8. An ontology based information system for the management of institutional repository's collections

    NASA Astrophysics Data System (ADS)

    Tsolakidis, A.; Kakoulidis, P.; Skourlas, C.

    2015-02-01

    In this paper we discuss a simple methodological approach to create, and customize institutional repositories for the domain of the technological education. The use of the open source software platform of DSpace is proposed to build up the repository application and provide access to digital resources including research papers, dissertations, administrative documents, educational material, etc. Also the use of owl ontologies is proposed for indexing and accessing the various, heterogeneous items stored in the repository. Customization and operation of a platform for the selection and use of terms or parts of similar existing owl ontologies is also described. This platform could be based on the open source software Protégé that supports owl, is widely used, and also supports visualization, SPARQL etc. The combined use of the owl platform and the DSpace repository form a basis for creating customized ontologies, accommodating the semantic metadata of items and facilitating searching.

  9. Large-Scale In-situ Experiments to Determine Geochemical Alterations and Microbial Activities at the Geological Repository

    NASA Astrophysics Data System (ADS)

    Choung, S.; Francis, A. J.; Um, W.; Choi, S.; Kim, S.; Park, J.; Kim, S.

    2013-12-01

    The countries that have generated nuclear power have facing problems on the disposal of accumulated radioactive wastes. Geological disposal method has been chosen in many countries including Korea. A safety issue after the closure of geological repository has been raised, because microbial activities lead overpressure in the underground facilities through gas production. In particular, biodegradable organic materials derived from low- and intermediate-level radioactive wastes play important role on microbial activities in the geological repository. This study performed large scale in-situ experiments using organic wastes and groundwater, and investigated geochemical alteration and microbial activities at early stage (~63 days) as representative of the period, after closure of the geological repository. The geochemical alteration controlled significantly the microorganism types and populations. Database of the biogeochemical alteration facilitates prediction of radionuclides' mobility and establishment of remedial strategy against unpredictable accidents and hazards at early stage right after closure of the geological repository.

  10. Disposal of high-level nuclear waste above the water table in arid regions

    USGS Publications Warehouse

    Roseboom, Eugene H.

    1983-01-01

    Locating a repository in the unsaturated zone of arid regions eliminates or simplifies many of the technological problems involved in designing a repository for operation below the water table and predicting its performance. It also offers possible accessibility and ease of monitoring throughout the operational period and possible retrieval of waste long after. The risks inherent in such a repository appear to be no greater than in one located in the saturated zone; in fact, many aspects of such a repository's performance will be much easier to predict and the uncertainties will be reduced correspondingly. A major new concern would be whether future climatic changes could produce significant consequences due to possible rise of the water table or increased flux of water through the repository. If spent fuel were used as a waste form, a second new concern would be the rates of escape of gaseous iodine-129 and carbon-14 to the atmosphere.

  11. Potential Future Igneous Activity at Yucca Mountain, Nevada

    NASA Astrophysics Data System (ADS)

    Cline, M.; Perry, F. V.; Valentine, G. A.; Smistad, E.

    2005-12-01

    Location, timing, and volumes of post-Miocene volcanic activity, along with expert judgement, provide the basis for assessing the probability of future volcanism intersecting a proposed repository for nuclear waste at Yucca Mountain, Nevada. Analog studies of eruptive centers in the region that may represent the style and extent of possible future igneous activity at Yucca Mountain have aided in defining the consequence scenarios for intrusion into and eruption through a proposed repository. Modeling of magmatic processes related to magma/proposed repository interactions has been used to assess the potential consequences of a future igneous event through a proposed repository at Yucca Mountain. Results of work to date indicate future igneous activity in the Yucca Mountain region has a very low probability of intersecting the proposed repository. Probability of a future event intersecting a proposed repository at Yucca Mountain is approximately 1.7 X 10-8 per year. Since completion of the Probabilistic Volcanic Hazard Assessment (PVHA) in 1996, anomalies representing potential buried volcanic centers have been identified from aeromagnetic surveys. A re-assessment of the hazard is currently underway to evaluate the probability of intersection in light of new information and to estimate the probability of one or more volcanic conduits located in the proposed repository along a dike that intersects the proposed repository. U.S. Nuclear Regulatory Commission regulations for siting and licensing a proposed repository require that the consequences of a disruptive event (igneous event) with annual probability greater than 1 X 10-8 be evaluated. Two consequence scenarios are considered; 1) igneous intrusion-groundwater transport case and 2) volcanic eruptive case. These scenarios equate to a dike or dike swarm intersecting repository drifts containing waste packages, formation of a conduit leading to a volcanic eruption through the repository that carries the contents of the waste packages into the atmosphere, deposition of a tephra sheet, and redistribution of the contaminated ash. In both cases radioactive material is released to the accessible environment either through groundwater transport or through the atmospheric dispersal and deposition. Six Quaternary volcanic centers exist within 20 km of Yucca Mountain. Lathrop Wells cone (LWC), the youngest (approximately 75,000 yrs), is a well-preserved cinder cone with associated flows and tephra sheet that provides an excellent analogue for consequence studies related to future volcanism. Cone, lavas, hydrovolcanic ash, and ash-fall tephra have been examined to estimate eruptive volume and eruption type. LWC ejecta volumes suggest basaltic volcanism may be waning in the Yucca Mountain region.. The eruptive products indicate a sequence of initial fissure fountaining, early Strombolian ash and lapilli deposition forming the scoria cone, a brief hydrovolcanic pulse (possibly limited to the NW sector), and a violent Strombolian phase. Mathematical models have been developed to represent magmatic processes and their consequences on proposed repository performance. These models address dike propagation, magma interaction and flow into drifts, eruption through the proposed repository, and post intrusion/eruption effects. These models continue to be refined to reduce the uncertainty associated with the consequences from a possible future igneous event.

  12. 10 CFR Appendix II to Part 960 - NRC and EPA Requirements for Preclosure Repository Performance

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 4 2012-01-01 2012-01-01 false NRC and EPA Requirements for Preclosure Repository Performance II Appendix II to Part 960 Energy DEPARTMENT OF ENERGY GENERAL GUIDELINES FOR THE PRELIMINARY SCREENING OF POTENTIAL SITES FOR A NUCLEAR WASTE REPOSITORY Pt. 960, App. II Appendix II to Part 960—NRC and...

  13. 10 CFR Appendix II to Part 960 - NRC and EPA Requirements for Preclosure Repository Performance

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 4 2011-01-01 2011-01-01 false NRC and EPA Requirements for Preclosure Repository Performance II Appendix II to Part 960 Energy DEPARTMENT OF ENERGY GENERAL GUIDELINES FOR THE PRELIMINARY SCREENING OF POTENTIAL SITES FOR A NUCLEAR WASTE REPOSITORY Pt. 960, App. II Appendix II to Part 960—NRC and...

  14. 10 CFR Appendix II to Part 960 - NRC and EPA Requirements for Preclosure Repository Performance

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 4 2013-01-01 2013-01-01 false NRC and EPA Requirements for Preclosure Repository Performance II Appendix II to Part 960 Energy DEPARTMENT OF ENERGY GENERAL GUIDELINES FOR THE PRELIMINARY SCREENING OF POTENTIAL SITES FOR A NUCLEAR WASTE REPOSITORY Pt. 960, App. II Appendix II to Part 960—NRC and...

  15. 10 CFR Appendix I to Part 960 - NRC and EPA Requirements for Postclosure Repository Performance

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 4 2013-01-01 2013-01-01 false NRC and EPA Requirements for Postclosure Repository Performance I Appendix I to Part 960 Energy DEPARTMENT OF ENERGY GENERAL GUIDELINES FOR THE PRELIMINARY SCREENING OF POTENTIAL SITES FOR A NUCLEAR WASTE REPOSITORY Pt. 960, App. I Appendix I to Part 960—NRC and...

  16. 10 CFR Appendix II to Part 960 - NRC and EPA Requirements for Preclosure Repository Performance

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 4 2014-01-01 2014-01-01 false NRC and EPA Requirements for Preclosure Repository Performance II Appendix II to Part 960 Energy DEPARTMENT OF ENERGY GENERAL GUIDELINES FOR THE PRELIMINARY SCREENING OF POTENTIAL SITES FOR A NUCLEAR WASTE REPOSITORY Pt. 960, App. II Appendix II to Part 960—NRC and...

  17. 75 FR 63080 - Interim Final Rule for Reporting Pre-Enactment Swap Transactions

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-14

    ... registered swap data repository (``SDR'') \\1\\ or to the Commission by the compliance date to be established... to the terms of such swaps. \\1\\ The term ``swap data repository'' is defined in Section 1a(48) of the... the date of the enactment of this subsection shall be reported to a registered swap data repository or...

  18. If SWORD Is the Answer, What Is the Question?: Use of the Simple Web-Service Offering Repository Deposit Protocol

    ERIC Educational Resources Information Center

    Lewis, Stuart; Hayes, Leonie; Newton-Wade, Vanessa; Corfield, Antony; Davis, Richard; Donohue, Tim; Wilson, Scott

    2009-01-01

    Purpose: The purpose of this paper is to describe the repository deposit protocol, Simple Web-service Offering Repository Deposit (SWORD), its development iteration, and some of its potential use cases. In addition, seven case studies of institutional use of SWORD are provided. Design/methodology/approach: The paper describes the recent…

  19. Personal Spaces in Public Repositories as a Facilitator for Open Educational Resource Usage

    ERIC Educational Resources Information Center

    Cohen, Anat; Reisman, Sorel; Sperling, Barbra Bied

    2015-01-01

    Learning object repositories are a shared, open and public space; however, the possibility and ability of personal expression in an open, global, public space is crucial. The aim of this study is to explore personal spaces in a big learning object repository as a facilitator for adoption of Open Educational Resources (OER) into teaching practices…

  20. Making the Most of What We Have Got: Enhancing the RADAR Repository to Support Research Planning

    ERIC Educational Resources Information Center

    Pike, Dawn; Siminson, Nicola Jane

    2017-01-01

    This article discusses how RADAR, the institutional repository (IR) at the Glasgow School of Art (GSA), has been modified to house an Annual Research Planning (ARP) template. A case study on the implementation of this research planning tool will outline the role that a repository and its staff can play in supporting individuals, enhancing…

  1. Crowdsourcing Content to Promote Community and Collection Development in Public Libraries

    ERIC Educational Resources Information Center

    Carr, Melissa Eleftherion

    2013-01-01

    With the Poetry Center at San Francisco State University, the author has begun to build an open-access digital repository for poetry chapbooks. The repository is essentially a chapbook exchange: a place for poets to share their current works. Users are invited to share their chapbooks via upload and as such gain access to the chapbook repository.…

  2. Development and Implementation of a Learning Object Repository for French Teaching and Learning: Issues and Promises

    ERIC Educational Resources Information Center

    Caws, Catherine

    2008-01-01

    This paper discusses issues surrounding the development of a learning object repository (FLORE) for teaching and learning French at the postsecondary level. An evaluation based on qualitative and quantitative data was set up in order to better assess how second-language (L2) students in French perceived the integration of this new repository into…

  3. Attitudes to the Rights and Rewards for Author Contributions to Repositories for Teaching and Learning

    ERIC Educational Resources Information Center

    Bates, Melanie; Loddington, Steve; Manuel, Sue; Oppenheim, Charles

    2007-01-01

    In the United Kingdom over the past few years there has been a dramatic growth of national and regional repositories to collect and disseminate resources related to teaching and learning. Most notable of these are the Joint Information Systems Committee's Online Repository for [Learning and Teaching] Materials as well as the Higher Education…

  4. Institutional Repositories in the UK: What Can the Google User Find There?

    ERIC Educational Resources Information Center

    Markland, Margaret

    2006-01-01

    This study investigates the efficiency of the Google search engine at retrieving items from 26 UK Institutional Repositories, covering a wide range of subject areas. One item is chosen from each repository and four searches are carried out: two keyword searches and two full title searches, each using both Google and then Google Scholar. A further…

  5. Centralized mouse repositories.

    PubMed

    Donahue, Leah Rae; Hrabe de Angelis, Martin; Hagn, Michael; Franklin, Craig; Lloyd, K C Kent; Magnuson, Terry; McKerlie, Colin; Nakagata, Naomi; Obata, Yuichi; Read, Stuart; Wurst, Wolfgang; Hörlein, Andreas; Davisson, Muriel T

    2012-10-01

    Because the mouse is used so widely for biomedical research and the number of mouse models being generated is increasing rapidly, centralized repositories are essential if the valuable mouse strains and models that have been developed are to be securely preserved and fully exploited. Ensuring the ongoing availability of these mouse strains preserves the investment made in creating and characterizing them and creates a global resource of enormous value. The establishment of centralized mouse repositories around the world for distributing and archiving these resources has provided critical access to and preservation of these strains. This article describes the common and specialized activities provided by major mouse repositories around the world.

  6. Centralized Mouse Repositories

    PubMed Central

    Donahue, Leah Rae; de Angelis, Martin Hrabe; Hagn, Michael; Franklin, Craig; Lloyd, K. C. Kent; Magnuson, Terry; McKerlie, Colin; Nakagata, Naomi; Obata, Yuichi; Read, Stuart; Wurst, Wolfgang; Hörlein, Andreas; Davisson, Muriel T.

    2013-01-01

    Because the mouse is used so widely for biomedical research and the number of mouse models being generated is increasing rapidly, centralized repositories are essential if the valuable mouse strains and models that have been developed are to be securely preserved and fully exploited. Ensuring the ongoing availability of these mouse strains preserves the investment made in creating and characterizing them and creates a global resource of enormous value. The establishment of centralized mouse repositories around the world for distributing and archiving these resources has provided critical access to and preservation of these strains. This article describes the common and specialized activities provided by major mouse repositories around the world. PMID:22945696

  7. Digitizing dissertations for an institutional repository: a process and cost analysis.

    PubMed

    Piorun, Mary; Palmer, Lisa A

    2008-07-01

    This paper describes the Lamar Soutter Library's process and costs associated with digitizing 300 doctoral dissertations for a newly implemented institutional repository at the University of Massachusetts Medical School. Project tasks included identifying metadata elements, obtaining and tracking permissions, converting the dissertations to an electronic format, and coordinating workflow between library departments. Each dissertation was scanned, reviewed for quality control, enhanced with a table of contents, processed through an optical character recognition function, and added to the institutional repository. Three hundred and twenty dissertations were digitized and added to the repository for a cost of $23,562, or $0.28 per page. Seventy-four percent of the authors who were contacted (n = 282) granted permission to digitize their dissertations. Processing time per title was 170 minutes, for a total processing time of 906 hours. In the first 17 months, full-text dissertations in the collection were downloaded 17,555 times. Locally digitizing dissertations or other scholarly works for inclusion in institutional repositories can be cost effective, especially if small, defined projects are chosen. A successful project serves as an excellent recruitment strategy for the institutional repository and helps libraries build new relationships. Challenges include workflow, cost, policy development, and copyright permissions.

  8. A laboratory validation study of the time-lapse oscillatory pumping test for leakage detection in geological repositories

    NASA Astrophysics Data System (ADS)

    Sun, Alexander Y.; Lu, Jiemin; Islam, Akand

    2017-05-01

    Geologic repositories are extensively used for disposing byproducts in mineral and energy industries. The safety and reliability of these repositories are a primary concern to environmental regulators and the public. Time-lapse oscillatory pumping test (OPT) has been introduced recently as a pressure-based technique for detecting potential leakage in geologic repositories. By routinely conducting OPT at a number of pulsing frequencies, an operator may identify the potential repository anomalies in the frequency domain, alleviating the ambiguity caused by reservoir noise and improving the signal-to-noise ratio. Building on previous theoretical and field studies, this work performed a series of laboratory experiments to validate the concept of time-lapse OPT using a custom made, stainless steel tank under relatively high pressures. The experimental configuration simulates a miniature geologic storage repository consisting of three layers (i.e., injection zone, caprock, and above-zone aquifer). Results show that leakage in the injection zone led to deviations in the power spectrum of observed pressure data, and the amplitude of which also increases with decreasing pulsing frequencies. The experimental results are further analyzed by developing a 3D flow model, using which the model parameters are estimated through frequency domain inversion.

  9. YUCCA MOUNTAIN: Earth-Science Issues at a Geologic Repository for High-Level Nuclear Waste

    NASA Astrophysics Data System (ADS)

    Long, Jane C. S.

    2004-05-01

    The nation has over 40,000 metric tonnes (MT) of nuclear waste destined for disposal in a geologic repository at Yucca Mountain. In this review, we highlight some of the important geoscience issues associated with the project and place them in the context of the process by which a final decision on Yucca Mountain will be made. The issues include understanding how water could infiltrate the repository, corrode the canisters, dissolve the waste, and transport it to the biosphere during a 10,000-year compliance period in a region, the Basin and Range province, that is known for seismic and volcanic activity. Although the site is considered to be "dry," a considerable amount of water is present as pore waters and as structural water in zeolites. The geochemical environment is oxidizing, and the present repository design will maintain temperatures at greater than 100°C for thousands of years. Geoscientists in this project are challenged to make unprecedented predictions about coupled thermal, hydrologic, mechanical, and geochemical processes governing the future behavior of the repository and to conduct research in a regulatory and legal environment that requires a quantitative analysis of repository performance.

  10. Can Data Repositories Help Find Effective Treatments for Complex Diseases?

    PubMed Central

    Farber, Gregory K.

    2016-01-01

    There are many challenges to developing treatments for complex diseases. This review explores the question of whether it is possible to imagine a data repository that would increase the pace of understanding complex diseases sufficiently well to facilitate the development of effective treatments. First, consideration is given to the amount of data that might be needed for such a data repository and whether the existing data storage infrastructure is enough. Several successful data repositories are then examined to see if they have common characteristics. An area of science where unsuccessful attempts to develop a data infrastructure is then described to see what lessons could be learned for a data repository devoted to complex disease. Then, a variety of issues related to sharing data are discussed. In some of these areas, it is reasonably clear how to move forward. In other areas, there are significant open questions that need to be addressed by all data repositories. Using that baseline information, the question of whether data archives can be effective in understanding a complex disease is explored. The major goal of such a data archive is likely to be identifying biomarkers that define sub-populations of the disease. PMID:27018167

  11. Can data repositories help find effective treatments for complex diseases?

    PubMed

    Farber, Gregory K

    2017-05-01

    There are many challenges to developing treatments for complex diseases. This review explores the question of whether it is possible to imagine a data repository that would increase the pace of understanding complex diseases sufficiently well to facilitate the development of effective treatments. First, consideration is given to the amount of data that might be needed for such a data repository and whether the existing data storage infrastructure is enough. Several successful data repositories are then examined to see if they have common characteristics. An area of science where unsuccessful attempts to develop a data infrastructure is then described to see what lessons could be learned for a data repository devoted to complex disease. Then, a variety of issues related to sharing data are discussed. In some of these areas, it is reasonably clear how to move forward. In other areas, there are significant open questions that need to be addressed by all data repositories. Using that baseline information, the question of whether data archives can be effective in understanding a complex disease is explored. The major goal of such a data archive is likely to be identifying biomarkers that define sub-populations of the disease. Published by Elsevier Ltd.

  12. Integrating repositories with fuel cycles: The airport authority model

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Forsberg, C.

    2012-07-01

    The organization of the fuel cycle is a legacy of World War II and the cold war. Fuel cycle facilities were developed and deployed without consideration of the waste management implications. This led to the fuel cycle model of a geological repository site with a single owner, a single function (disposal), and no other facilities on site. Recent studies indicate large economic, safety, repository performance, nonproliferation, and institutional incentives to collocate and integrate all back-end facilities. Site functions could include geological disposal of spent nuclear fuel (SNF) with the option for future retrievability, disposal of other wastes, reprocessing with fuelmore » fabrication, radioisotope production, other facilities that generate significant radioactive wastes, SNF inspection (navy and commercial), and related services such as SNF safeguards equipment testing and training. This implies a site with multiple facilities with different owners sharing some facilities and using common facilities - the repository and SNF receiving. This requires a different repository site institutional structure. We propose development of repository site authorities modeled after airport authorities. Airport authorities manage airports with government-owned runways, collocated or shared public and private airline terminals, commercial and federal military facilities, aircraft maintenance bases, and related operations - all enabled and benefiting the high-value runway asset and access to it via taxi ways. With a repository site authority the high value asset is the repository. The SNF and HLW receiving and storage facilities (equivalent to the airport terminal) serve the repository, any future reprocessing plants, and others with needs for access to SNF and other wastes. Non-public special-built roadways and on-site rail lines (equivalent to taxi ways) connect facilities. Airport authorities are typically chartered by state governments and managed by commissions with members appointed by the state governor, county governments, and city governments. This structure (1) enables state and local governments to work together to maximize job and tax benefits to local communities and the state, (2) provides a mechanism to address local concerns such as airport noise, and (3) creates an institutional structure with large incentives to maximize the value of the common asset, the runway. A repository site authority would have a similar structure and be the local interface to any national waste management authority. (authors)« less

  13. DOE Office of Scientific and Technical Information (OSTI.GOV)

    Broome, S. T.; Bauer, S. J.; Hansen, F. D.

    Design, analysis and performance assessment of potential salt repositories for heat-generating nuclear waste require knowledge of thermal, mechanical, and fluid transport properties of reconsolidating granular salt. So, to inform salt repository evaluations, we have undertaken an experimental program to determine Bulk and Young’s moduli and Poisson’s ratio of reconsolidated granular salt as a function of porosity and temperature and to establish the deformational processes by which the salt reconsolidates. Our tests were conducted at 100, 175, and 250 °C. In hydrostatic tests, confining pressure is increased to 20 MPa with periodic unload/reload loops to determine K. Volume strain increases withmore » increasing temperature. In shear tests at 2.5 and 5 MPa confining pressure, after confining pressure is applied, the crushed salt is subjected to a differential stress, with periodic unload/reload loops to determine E and ν. At predetermined differential stress levels the stress is held constant and the salt consolidates. Displacement gages mounted on the samples show little lateral deformation until the samples reach a porosity of ~10 %. Interestingly, vapor is vented only for 250 °C tests and condenses at the vent port. It is hypothesized that the brine originates from fluid inclusions, which were made accessible by heating and intragranular deformational processes including decrepitation. Furthermore, identification and documentation of consolidation processes are inferred from optical and scanning electron microstructural observations. As a result, densification at low porosity is enhanced by water film on grain boundaries that enables solution-precipitation phenomena.« less

  14. SWATH Mass Spectrometry Performance Using Extended Peptide MS/MS Assay Libraries.

    PubMed

    Wu, Jemma X; Song, Xiaomin; Pascovici, Dana; Zaw, Thiri; Care, Natasha; Krisp, Christoph; Molloy, Mark P

    2016-07-01

    The use of data-independent acquisition methods such as SWATH for mass spectrometry based proteomics is usually performed with peptide MS/MS assay libraries which enable identification and quantitation of peptide peak areas. Reference assay libraries can be generated locally through information dependent acquisition, or obtained from community data repositories for commonly studied organisms. However, there have been no studies performed to systematically evaluate how locally generated or repository-based assay libraries affect SWATH performance for proteomic studies. To undertake this analysis, we developed a software workflow, SwathXtend, which generates extended peptide assay libraries by integration with a local seed library and delivers statistical analysis of SWATH-quantitative comparisons. We designed test samples using peptides from a yeast extract spiked into peptides from human K562 cell lysates at three different ratios to simulate protein abundance change comparisons. SWATH-MS performance was assessed using local and external assay libraries of varying complexities and proteome compositions. These experiments demonstrated that local seed libraries integrated with external assay libraries achieve better performance than local assay libraries alone, in terms of the number of identified peptides and proteins and the specificity to detect differentially abundant proteins. Our findings show that the performance of extended assay libraries is influenced by the MS/MS feature similarity of the seed and external libraries, while statistical analysis using multiple testing corrections increases the statistical rigor needed when searching against large extended assay libraries. © 2016 by The American Society for Biochemistry and Molecular Biology, Inc.

  15. SWATH Mass Spectrometry Performance Using Extended Peptide MS/MS Assay Libraries*

    PubMed Central

    Wu, Jemma X.; Song, Xiaomin; Pascovici, Dana; Zaw, Thiri; Care, Natasha; Krisp, Christoph; Molloy, Mark P.

    2016-01-01

    The use of data-independent acquisition methods such as SWATH for mass spectrometry based proteomics is usually performed with peptide MS/MS assay libraries which enable identification and quantitation of peptide peak areas. Reference assay libraries can be generated locally through information dependent acquisition, or obtained from community data repositories for commonly studied organisms. However, there have been no studies performed to systematically evaluate how locally generated or repository-based assay libraries affect SWATH performance for proteomic studies. To undertake this analysis, we developed a software workflow, SwathXtend, which generates extended peptide assay libraries by integration with a local seed library and delivers statistical analysis of SWATH-quantitative comparisons. We designed test samples using peptides from a yeast extract spiked into peptides from human K562 cell lysates at three different ratios to simulate protein abundance change comparisons. SWATH-MS performance was assessed using local and external assay libraries of varying complexities and proteome compositions. These experiments demonstrated that local seed libraries integrated with external assay libraries achieve better performance than local assay libraries alone, in terms of the number of identified peptides and proteins and the specificity to detect differentially abundant proteins. Our findings show that the performance of extended assay libraries is influenced by the MS/MS feature similarity of the seed and external libraries, while statistical analysis using multiple testing corrections increases the statistical rigor needed when searching against large extended assay libraries. PMID:27161445

  16. A Comprehensive, Automatically Updated Fungal ITS Sequence Dataset for Reference-Based Chimera Control in Environmental Sequencing Efforts.

    PubMed

    Nilsson, R Henrik; Tedersoo, Leho; Ryberg, Martin; Kristiansson, Erik; Hartmann, Martin; Unterseher, Martin; Porter, Teresita M; Bengtsson-Palme, Johan; Walker, Donald M; de Sousa, Filipe; Gamper, Hannes Andres; Larsson, Ellen; Larsson, Karl-Henrik; Kõljalg, Urmas; Edgar, Robert C; Abarenkov, Kessy

    2015-01-01

    The nuclear ribosomal internal transcribed spacer (ITS) region is the most commonly chosen genetic marker for the molecular identification of fungi in environmental sequencing and molecular ecology studies. Several analytical issues complicate such efforts, one of which is the formation of chimeric-artificially joined-DNA sequences during PCR amplification or sequence assembly. Several software tools are currently available for chimera detection, but rely to various degrees on the presence of a chimera-free reference dataset for optimal performance. However, no such dataset is available for use with the fungal ITS region. This study introduces a comprehensive, automatically updated reference dataset for fungal ITS sequences based on the UNITE database for the molecular identification of fungi. This dataset supports chimera detection throughout the fungal kingdom and for full-length ITS sequences as well as partial (ITS1 or ITS2 only) datasets. The performance of the dataset on a large set of artificial chimeras was above 99.5%, and we subsequently used the dataset to remove nearly 1,000 compromised fungal ITS sequences from public circulation. The dataset is available at http://unite.ut.ee/repository.php and is subject to web-based third-party curation.

  17. Microbial community controls on decomposition and soil carbon storage

    NASA Astrophysics Data System (ADS)

    Frey, S. D.

    2016-12-01

    Soil is one of the most diverse habitats on Earth and one of the least characterized in terms of the identification and ecological roles of soil organisms. Soils also contain the largest repository of organic C in the terrestrial biosphere and the activities of heterotrophic soil organisms are responsible for one of the largest annual fluxes of CO2 to the atmosphere. A fundamental controversy in ecosystem ecology is the degree to which identification of microbial taxa informs our ability to understand and model ecosystem-scale processes, such as soil carbon storage and fluxes. We have evidence that microbial identity does matter, particularly in a global change context where soil microorganisms experience selective pressures to adapt to changing environments. In particular, our work at the Harvard Forest Long-term Ecological Research (LTER) site demonstrates that the microbial community is fundamentally altered by global change stressors (climate warming, nitrogen deposition, biotic invasion) and that microbial taxa exposed to long-term environmental change exhibit an altered capacity to decompose organic matter. This talk will discuss the relative importance of changes in microbial community structure versus microbial physiology for soil organic matter degradation and stabilization.

  18. Pattern-based information portal for business plan co-creation

    NASA Astrophysics Data System (ADS)

    Bontchev, Boyan; Ruskov, Petko; Tanev, Stoyan

    2011-03-01

    Creation of business plans helps entrepreneurs in managing identification of business opportunities and committing necessary resources for process evolution. Applying patterns in business plan creation facilitates the identification of effective solutions that were adopted in the past and may provide a basis for adopting similar solutions in the future within given business context. The article presents the system design of an information portal for business plan co-creation based on patterns. The portal is going to provide start-up and entrepreneurs with ready-to-modify business plan patterns in order to help them in development of effective and efficient business plans. It will facilitate entrepreneurs in co-experimenting and co-learning more frequently and faster. Moreover, the paper focuses on the software architecture of the pattern based portal and explains the functionality of its modules, namely the pattern designer, pattern repository services and agent-based pattern implementers. It explains their role for business process co-creation, storing and managing patterns described formally, and selecting patterns best suited for specific business case. Thus, innovative entrepreneurs will be guided by the portal in co-writing winning business plans and staying competitive in the present day dynamic globalized environment.

  19. Pattern-based information portal for business plan co-creation

    NASA Astrophysics Data System (ADS)

    Bontchev, Boyan; Ruskov, Petko; Tanev, Stoyan

    2010-10-01

    Creation of business plans helps entrepreneurs in managing identification of business opportunities and committing necessary resources for process evolution. Applying patterns in business plan creation facilitates the identification of effective solutions that were adopted in the past and may provide a basis for adopting similar solutions in the future within given business context. The article presents the system design of an information portal for business plan co-creation based on patterns. The portal is going to provide start-up and entrepreneurs with ready-to-modify business plan patterns in order to help them in development of effective and efficient business plans. It will facilitate entrepreneurs in co-experimenting and co-learning more frequently and faster. Moreover, the paper focuses on the software architecture of the pattern based portal and explains the functionality of its modules, namely the pattern designer, pattern repository services and agent-based pattern implementers. It explains their role for business process co-creation, storing and managing patterns described formally, and selecting patterns best suited for specific business case. Thus, innovative entrepreneurs will be guided by the portal in co-writing winning business plans and staying competitive in the present day dynamic globalized environment.

  20. Adaptive dynamic programming approach to experience-based systems identification and control.

    PubMed

    Lendaris, George G

    2009-01-01

    Humans have the ability to make use of experience while selecting their control actions for distinct and changing situations, and their process speeds up and have enhanced effectiveness as more experience is gained. In contrast, current technological implementations slow down as more knowledge is stored. A novel way of employing Approximate (or Adaptive) Dynamic Programming (ADP) is described that shifts the underlying Adaptive Critic type of Reinforcement Learning method "up a level", away from designing individual (optimal) controllers to that of developing on-line algorithms that efficiently and effectively select designs from a repository of existing controller solutions (perhaps previously developed via application of ADP methods). The resulting approach is called Higher-Level Learning Algorithm. The approach and its rationale are described and some examples of its application are given. The notions of context and context discernment are important to understanding the human abilities noted above. These are first defined, in a manner appropriate to controls and system-identification, and as a foundation relating to the application arena, a historical view of the various phases during development of the controls field is given, organized by how the notion 'context' was, or was not, involved in each phase.

  1. A Comprehensive, Automatically Updated Fungal ITS Sequence Dataset for Reference-Based Chimera Control in Environmental Sequencing Efforts

    PubMed Central

    Nilsson, R. Henrik; Tedersoo, Leho; Ryberg, Martin; Kristiansson, Erik; Hartmann, Martin; Unterseher, Martin; Porter, Teresita M.; Bengtsson-Palme, Johan; Walker, Donald M.; de Sousa, Filipe; Gamper, Hannes Andres; Larsson, Ellen; Larsson, Karl-Henrik; Kõljalg, Urmas; Edgar, Robert C.; Abarenkov, Kessy

    2015-01-01

    The nuclear ribosomal internal transcribed spacer (ITS) region is the most commonly chosen genetic marker for the molecular identification of fungi in environmental sequencing and molecular ecology studies. Several analytical issues complicate such efforts, one of which is the formation of chimeric—artificially joined—DNA sequences during PCR amplification or sequence assembly. Several software tools are currently available for chimera detection, but rely to various degrees on the presence of a chimera-free reference dataset for optimal performance. However, no such dataset is available for use with the fungal ITS region. This study introduces a comprehensive, automatically updated reference dataset for fungal ITS sequences based on the UNITE database for the molecular identification of fungi. This dataset supports chimera detection throughout the fungal kingdom and for full-length ITS sequences as well as partial (ITS1 or ITS2 only) datasets. The performance of the dataset on a large set of artificial chimeras was above 99.5%, and we subsequently used the dataset to remove nearly 1,000 compromised fungal ITS sequences from public circulation. The dataset is available at http://unite.ut.ee/repository.php and is subject to web-based third-party curation. PMID:25786896

  2. Airborne microorganisms cultivable on naturally ventilated document repositories of the National Archive of Cuba.

    PubMed

    Borrego, Sofía; Perdomo, Ivette

    2016-02-01

    The quality of the indoor air can provide very useful information for the artwork conservation. The aim of the study was to evaluate the microbial concentration inside six document repositories of the National Archive of the Republic of Cuba in two months of 1 year. The repositories are large, high, and have a natural cross-ventilation system. The microbial sampling was done in July 2010 (summer or rainy month) and February 2011 (winter or dry month) using the SAS Super 100 biocollector at 100 L/min. An appropriate selective culture media were used to isolate fungi and bacteria. A high total microbial concentration on the north side of the building in two studied months was observed. The fungal concentrations were significantly higher in July 2010 in all repositories, while the bacterial concentrations were significantly higher mostly in February 2011 only in repositories located on the first and second floor of the building. Eight fungal genera in the indoor air of all environments were isolated. Regardless of the side of the analyzed building, Penicillium, Aspergillus, and Cladosporium were the predominant genera. Aspergillus flavus and Aspergillus niger were the species isolated in almost all of the analyzed repositories in the studied months. Gram-positive bacteria prevailed among bacterial groups isolated from indoor air repositories, and some percentages corresponded to the genera Bacillus and Streptomyces. In Cuba, the temperature and relative humidity are high during the whole year but the natural ventilation plays an important role in retarding microbial growth on materials.

  3. Assurance of Fault Management: Risk-Significant Adverse Condition Awareness

    NASA Technical Reports Server (NTRS)

    Fitz, Rhonda

    2016-01-01

    Fault Management (FM) systems are ranked high in risk-based assessment of criticality within flight software, emphasizing the importance of establishing highly competent domain expertise to provide assurance for NASA projects, especially as spaceflight systems continue to increase in complexity. Insight into specific characteristics of FM architectures seen embedded within safety- and mission-critical software systems analyzed by the NASA Independent Verification Validation (IVV) Program has been enhanced with an FM Technical Reference (TR) suite. Benefits are aimed beyond the IVV community to those that seek ways to efficiently and effectively provide software assurance to reduce the FM risk posture of NASA and other space missions. The identification of particular FM architectures, visibility, and associated IVV techniques provides a TR suite that enables greater assurance that critical software systems will adequately protect against faults and respond to adverse conditions. The role FM has with regard to overall asset protection of flight software systems is being addressed with the development of an adverse condition (AC) database encompassing flight software vulnerabilities.Identification of potential off-nominal conditions and analysis to determine how a system responds to these conditions are important aspects of hazard analysis and fault management. Understanding what ACs the mission may face, and ensuring they are prevented or addressed is the responsibility of the assurance team, which necessarily should have insight into ACs beyond those defined by the project itself. Research efforts sponsored by NASAs Office of Safety and Mission Assurance defined terminology, categorized data fields, and designed a baseline repository that centralizes and compiles a comprehensive listing of ACs and correlated data relevant across many NASA missions. This prototype tool helps projects improve analysis by tracking ACs, and allowing queries based on project, mission type, domain component, causal fault, and other key characteristics. The repository has a firm structure, initial collection of data, and an interface established for informational queries, with plans for integration within the Enterprise Architecture at NASA IVV, enabling support and accessibility across the Agency. The development of an improved workflow process for adaptive, risk-informed FM assurance is currently underway.

  4. The SoRReL papers: Recent publications of the Software Reuse Repository Lab

    NASA Technical Reports Server (NTRS)

    Eichmann, David A. (Editor)

    1992-01-01

    The entire publication is presented of some of the papers recently published by the SoRReL. Some typical titles are as follows: Design of a Lattice-Based Faceted Classification System; A Hybrid Approach to Software Reuse Repository Retrieval; Selecting Reusable Components Using Algebraic Specifications; Neural Network-Based Retrieval from Reuse Repositories; and A Neural Net-Based Approach to Software Metrics.

  5. Can Web 2.0 Enhance Community Participation in an Institutional Repository? The Case of PocketKnowledge at Teachers College, Columbia University

    ERIC Educational Resources Information Center

    Cocciolo, Anthony

    2010-01-01

    This project investigates if a Web 2.0 approach to designing an institutional repository can positively impact community participation. To study this, two institutional repositories (one Web 2.0, the other not) are used within the same institution. Results indicate that the use of a Web 2.0 approach significantly enhances community participation.…

  6. Engaging Researchers with the World's First Scholarly Arts Repositories: Ten Years after the UK's Kultur Project

    ERIC Educational Resources Information Center

    Meece, Stephanie; Robinson, Amy; Gramstadt, Marie-Therese

    2017-01-01

    Open access institutional repositories can be ill-equipped to manage the complexity of research outputs from departments of fine arts, media, drama, music, cultural heritage, and the creative arts in general. The U.K.-based Kultur project was funded to create a flexible multimedia repository model using EPrints software. The project launched the…

  7. Doing Your Science While You're in Orbit

    NASA Astrophysics Data System (ADS)

    Green, Mark L.; Miller, Stephen D.; Vazhkudai, Sudharshan S.; Trater, James R.

    2010-11-01

    Large-scale neutron facilities such as the Spallation Neutron Source (SNS) located at Oak Ridge National Laboratory need easy-to-use access to Department of Energy Leadership Computing Facilities and experiment repository data. The Orbiter thick- and thin-client and its supporting Service Oriented Architecture (SOA) based services (available at https://orbiter.sns.gov) consist of standards-based components that are reusable and extensible for accessing high performance computing, data and computational grid infrastructure, and cluster-based resources easily from a user configurable interface. The primary Orbiter system goals consist of (1) developing infrastructure for the creation and automation of virtual instrumentation experiment optimization, (2) developing user interfaces for thin- and thick-client access, (3) provide a prototype incorporating major instrument simulation packages, and (4) facilitate neutron science community access and collaboration. The secure Orbiter SOA authentication and authorization is achieved through the developed Virtual File System (VFS) services, which use Role-Based Access Control (RBAC) for data repository file access, thin-and thick-client functionality and application access, and computational job workflow management. The VFS Relational Database Management System (RDMS) consists of approximately 45 database tables describing 498 user accounts with 495 groups over 432,000 directories with 904,077 repository files. Over 59 million NeXus file metadata records are associated to the 12,800 unique NeXus file field/class names generated from the 52,824 repository NeXus files. Services that enable (a) summary dashboards of data repository status with Quality of Service (QoS) metrics, (b) data repository NeXus file field/class name full text search capabilities within a Google like interface, (c) fully functional RBAC browser for the read-only data repository and shared areas, (d) user/group defined and shared metadata for data repository files, (e) user, group, repository, and web 2.0 based global positioning with additional service capabilities are currently available. The SNS based Orbiter SOA integration progress with the Distributed Data Analysis for Neutron Scattering Experiments (DANSE) software development project is summarized with an emphasis on DANSE Central Services and the Virtual Neutron Facility (VNF). Additionally, the DANSE utilization of the Orbiter SOA authentication, authorization, and data transfer services best practice implementations are presented.

  8. Integrated Proteomic Pipeline Using Multiple Search Engines for a Proteogenomic Study with a Controlled Protein False Discovery Rate.

    PubMed

    Park, Gun Wook; Hwang, Heeyoun; Kim, Kwang Hoe; Lee, Ju Yeon; Lee, Hyun Kyoung; Park, Ji Yeong; Ji, Eun Sun; Park, Sung-Kyu Robin; Yates, John R; Kwon, Kyung-Hoon; Park, Young Mok; Lee, Hyoung-Joo; Paik, Young-Ki; Kim, Jin Young; Yoo, Jong Shin

    2016-11-04

    In the Chromosome-Centric Human Proteome Project (C-HPP), false-positive identification by peptide spectrum matches (PSMs) after database searches is a major issue for proteogenomic studies using liquid-chromatography and mass-spectrometry-based large proteomic profiling. Here we developed a simple strategy for protein identification, with a controlled false discovery rate (FDR) at the protein level, using an integrated proteomic pipeline (IPP) that consists of four engrailed steps as follows. First, using three different search engines, SEQUEST, MASCOT, and MS-GF+, individual proteomic searches were performed against the neXtProt database. Second, the search results from the PSMs were combined using statistical evaluation tools including DTASelect and Percolator. Third, the peptide search scores were converted into E-scores normalized using an in-house program. Last, ProteinInferencer was used to filter the proteins containing two or more peptides with a controlled FDR of 1.0% at the protein level. Finally, we compared the performance of the IPP to a conventional proteomic pipeline (CPP) for protein identification using a controlled FDR of <1% at the protein level. Using the IPP, a total of 5756 proteins (vs 4453 using the CPP) including 477 alternative splicing variants (vs 182 using the CPP) were identified from human hippocampal tissue. In addition, a total of 10 missing proteins (vs 7 using the CPP) were identified with two or more unique peptides, and their tryptic peptides were validated using MS/MS spectral pattern from a repository database or their corresponding synthetic peptides. This study shows that the IPP effectively improved the identification of proteins, including alternative splicing variants and missing proteins, in human hippocampal tissues for the C-HPP. All RAW files used in this study were deposited in ProteomeXchange (PXD000395).

  9. Efficient Discovery of De-identification Policies Through a Risk-Utility Frontier

    PubMed Central

    Xia, Weiyi; Heatherly, Raymond; Ding, Xiaofeng; Li, Jiuyong; Malin, Bradley

    2014-01-01

    Modern information technologies enable organizations to capture large quantities of person-specific data while providing routine services. Many organizations hope, or are legally required, to share such data for secondary purposes (e.g., validation of research findings) in a de-identified manner. In previous work, it was shown de-identification policy alternatives could be modeled on a lattice, which could be searched for policies that met a prespecified risk threshold (e.g., likelihood of re-identification). However, the search was limited in several ways. First, its definition of utility was syntactic - based on the level of the lattice - and not semantic - based on the actual changes induced in the resulting data. Second, the threshold may not be known in advance. The goal of this work is to build the optimal set of policies that trade-off between privacy risk (R) and utility (U), which we refer to as a R-U frontier. To model this problem, we introduce a semantic definition of utility, based on information theory, that is compatible with the lattice representation of policies. To solve the problem, we initially build a set of policies that define a frontier. We then use a probability-guided heuristic to search the lattice for policies likely to update the frontier. To demonstrate the effectiveness of our approach, we perform an empirical analysis with the Adult dataset of the UCI Machine Learning Repository. We show that our approach can construct a frontier closer to optimal than competitive approaches by searching a smaller number of policies. In addition, we show that a frequently followed de-identification policy (i.e., the Safe Harbor standard of the HIPAA Privacy Rule) is suboptimal in comparison to the frontier discovered by our approach. PMID:25520961

  10. Efficient Discovery of De-identification Policies Through a Risk-Utility Frontier.

    PubMed

    Xia, Weiyi; Heatherly, Raymond; Ding, Xiaofeng; Li, Jiuyong; Malin, Bradley

    2013-01-01

    Modern information technologies enable organizations to capture large quantities of person-specific data while providing routine services. Many organizations hope, or are legally required, to share such data for secondary purposes (e.g., validation of research findings) in a de-identified manner. In previous work, it was shown de-identification policy alternatives could be modeled on a lattice, which could be searched for policies that met a prespecified risk threshold (e.g., likelihood of re-identification). However, the search was limited in several ways. First, its definition of utility was syntactic - based on the level of the lattice - and not semantic - based on the actual changes induced in the resulting data. Second, the threshold may not be known in advance. The goal of this work is to build the optimal set of policies that trade-off between privacy risk (R) and utility (U), which we refer to as a R-U frontier. To model this problem, we introduce a semantic definition of utility, based on information theory, that is compatible with the lattice representation of policies. To solve the problem, we initially build a set of policies that define a frontier. We then use a probability-guided heuristic to search the lattice for policies likely to update the frontier. To demonstrate the effectiveness of our approach, we perform an empirical analysis with the Adult dataset of the UCI Machine Learning Repository. We show that our approach can construct a frontier closer to optimal than competitive approaches by searching a smaller number of policies. In addition, we show that a frequently followed de-identification policy (i.e., the Safe Harbor standard of the HIPAA Privacy Rule) is suboptimal in comparison to the frontier discovered by our approach.

  11. Data Citation Concept for CMIP6

    NASA Astrophysics Data System (ADS)

    Stockhause, M.; Toussaint, F.; Lautenschlager, M.; Lawrence, B.

    2015-12-01

    There is a broad consensus among data centers and scientific publishers on Force 11's 'Joint Declaration of Data Citation Principles'. To put these principles into operation is not always as straight forward. The focus for CMIP6 data citations lies on the citation of data created by others and used in an analysis underlying the article. And for this source data usually no article of the data creators is available ('stand-alone data publication'). The planned data citation granularities are model data (data collections containing all datasets provided for the project by a single model) and experiment data (data collections containing all datasets for a scientific experiment run by a single model). In case of large international projects or activities like CMIP, the data is commonly stored and disseminated by multiple repositories in a federated data infrastructure such as the Earth System Grid Federation (ESGF). The individual repositories are subject to different institutional and national policies. A Data Management Plan (DMP) will define a certain standard for the repositories including data handling procedures. Another aspect of CMIP data, relevant for data citations, is its dynamic nature. For such large data collections, datasets are added, revised and retracted for years, before the data collection becomes stable for a data citation entity including all model or simulation data. Thus, a critical issue for ESGF is data consistency, requiring thorough dataset versioning to enable the identification of the data collection in the cited version. Currently, the ESGF is designed for accessing the latest dataset versions. Data citation introduces the necessity to support older and retracted dataset versions by storing metadata even beyond data availability (data unpublished in ESGF). Apart from ESGF, other infrastructure components exist for CMIP, which provide information that has to be connected to the CMIP6 data, e.g. ES-DOC providing information on models and simulations and the IPCC Data Distribution Centre (DDC) storing a subset of data together with available metadata (ES-DOC) for the long-term reuse of the interdisciplinary community. Other connections exist to standard project vocabularies, to personal identifiers (e.g. ORCID), or to data products (including provenance information).

  12. SATORI: a system for ontology-guided visual exploration of biomedical data repositories.

    PubMed

    Lekschas, Fritz; Gehlenborg, Nils

    2018-04-01

    The ever-increasing number of biomedical datasets provides tremendous opportunities for re-use but current data repositories provide limited means of exploration apart from text-based search. Ontological metadata annotations provide context by semantically relating datasets. Visualizing this rich network of relationships can improve the explorability of large data repositories and help researchers find datasets of interest. We developed SATORI-an integrative search and visual exploration interface for the exploration of biomedical data repositories. The design is informed by a requirements analysis through a series of semi-structured interviews. We evaluated the implementation of SATORI in a field study on a real-world data collection. SATORI enables researchers to seamlessly search, browse and semantically query data repositories via two visualizations that are highly interconnected with a powerful search interface. SATORI is an open-source web application, which is freely available at http://satori.refinery-platform.org and integrated into the Refinery Platform. nils@hms.harvard.edu. Supplementary data are available at Bioinformatics online.

  13. Geochemical Results of Lysimeter Sampling at the Manning Canyon Repository in the Mercur Mining District, Utah

    USGS Publications Warehouse

    Earle, John; Choate, LaDonna

    2010-01-01

    This report presents chemical characteristics of transient unsaturated-zone water collected by lysimeter from the Manning Canyon repository site in Utah. Data collected by U.S. Geological Survey and U.S. Department of the Interior, Bureau of Land Management scientists under an intragovernmental order comprise the existing body of hydrochemical information on unsaturated-zone conditions at the site and represent the first effort to characterize the chemistry of the soil pore water surrounding the repository. Analyzed samples showed elevated levels of arsenic, barium, chromium, and strontium, which are typical of acidic mine drainage. The range of major-ion concentrations generally showed expected soil values. Although subsequent sampling is necessary to determine long-term effects of the repository, current results provide initial data concerning reactive processes of precipitation on the mine tailings and waste rock stored at the site and provide information on the effectiveness of reclamation operations at the Manning Canyon repository.

  14. Assuring the Quality of Agricultural Learning Repositories: Issues for the Learning Object Metadata Creation Process of the CGIAR

    NASA Astrophysics Data System (ADS)

    Zschocke, Thomas; Beniest, Jan

    The Consultative Group on International Agricultural Re- search (CGIAR) has established a digital repository to share its teaching and learning resources along with descriptive educational information based on the IEEE Learning Object Metadata (LOM) standard. As a critical component of any digital repository, quality metadata are critical not only to enable users to find more easily the resources they require, but also for the operation and interoperability of the repository itself. Studies show that repositories have difficulties in obtaining good quality metadata from their contributors, especially when this process involves many different stakeholders as is the case with the CGIAR as an international organization. To address this issue the CGIAR began investigating the Open ECBCheck as well as the ISO/IEC 19796-1 standard to establish quality protocols for its training. The paper highlights the implications and challenges posed by strengthening the metadata creation workflow for disseminating learning objects of the CGIAR.

  15. DataONE: Gateway to Earth and Environmental Data Repositories

    NASA Astrophysics Data System (ADS)

    Koskela, R.; Michener, W. K.; Vieglais, D.; Budden, A. E.

    2017-12-01

    DataONE (Data Observation Network for Earth) is a National Science Foundation DataNet project that enables universal access to data and also facilitates researchers in fulfilling their need for data management and in providing secure and permanent access to their data. DataONE offers the scientific community a suite of tools and training materials that cover all aspects of the data life cycle from data collection, to management, analysis and publication. Data repositories affiliated with DataONE are referred to as Member Nodes and represent large regional, national and international research networks, agencies, and other institutions. As part of the DataONE Federation, the repositories gain access to a range of value-added services to support their users. These services include usage tracking and reporting, content replication, and the ability to register the services created by the repository. In addition, DataONE and the California Digital Library manage ONEShare, a repository that accepts content submitted through Dash, a platform allowing researchers to easily describe, deposit and share their research data.

  16. A Preliminary Performance Assessment for Salt Disposal of High-Level Nuclear Waste - 12173

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Lee, Joon H.; Clayton, Daniel; Jove-Colon, Carlos

    2012-07-01

    A salt repository is one of the four geologic media currently under study by the U.S. DOE Office of Nuclear Energy to support the development of a long-term strategy for geologic disposal of commercial used nuclear fuel (UNF) and high-level radioactive waste (HLW). The immediate goal of the generic salt repository study is to develop the necessary modeling tools to evaluate and improve the understanding of the repository system response and processes relevant to long-term disposal of UNF and HLW in a salt formation. The current phase of this study considers representative geologic settings and features adopted from previous studiesmore » for salt repository sites. For the reference scenario, the brine flow rates in the repository and underlying interbeds are very low, and transport of radionuclides in the transport pathways is dominated by diffusion and greatly retarded by sorption on the interbed filling materials. I-129 is the dominant annual dose contributor at the hypothetical accessible environment, but the calculated mean annual dose is negligibly small. For the human intrusion (or disturbed) scenario, the mean mass release rate and mean annual dose histories are very different from those for the reference scenario. Actinides including Pu-239, Pu-242 and Np-237 are major annual dose contributors, and the calculated peak mean annual dose is acceptably low. A performance assessment model for a generic salt repository has been developed incorporating, where applicable, representative geologic settings and features adopted from literature data for salt repository sites. The conceptual model and scenario for radionuclide release and transport from a salt repository were developed utilizing literature data. The salt GDS model was developed in a probabilistic analysis framework. The preliminary performance analysis for demonstration of model capability is for an isothermal condition at the ambient temperature for the near field. The capability demonstration emphasizes key attributes of a salt repository that are potentially important to the long-term safe disposal of UNF and HLW. The analysis presents and discusses the results showing repository responses to different radionuclide release scenarios (undisturbed and human intrusion). For the reference (or nominal or undisturbed) scenario, the brine flow rates in the repository and underlying interbeds are very low, and transport of radionuclides in the transport pathways is dominated by diffusion and greatly retarded by sorption on the interbed filling materials. I-129 (non-sorbing and unlimited solubility with a very long half-life) is the dominant annual dose contributor at the hypothetical accessible environment, but the calculated mean annual dose is negligibly small that there is no meaningful consequence for the repository performance. For the human intrusion (or disturbed) scenario analysis, the mean mass release rate and mean annual dose histories are very different from those for the reference scenario analysis. Compared to the reference scenario, the relative annual dose contributions by soluble, non-sorbing fission products, particularly I-129, are much lower than by actinides including Pu-239, Pu-242 and Np-237. The lower relative mean annual dose contributions by the fission product radionuclides are due to their lower total inventory available for release (i.e., up to five affected waste packages), and the higher mean annual doses by the actinides are the outcome of the direct release of the radionuclides into the overlying aquifer having high water flow rates, thereby resulting in an early arrival of higher concentrations of the radionuclides at the biosphere drinking water well prior to their significant decay. The salt GDS model analysis has also identified the following future recommendations and/or knowledge gaps to improve and enhance the confidence of the future repository performance analysis. - Repository thermal loading by UNF and HLW, and the effect on the engineered barrier and near-field performance. - Closure and consolidation of salt rocks by creep deformation under the influence of thermal perturbation, and the effect on the engineered barrier and near-field performance. - Brine migration and radionuclide transport under the influence of thermal perturbation in generic salt repository environment, and the effect on the engineered barrier and near-field performance and far-field performance. - Near-field geochemistry and radionuclide mobility in generic salt repository environment (high ionic strength brines, elevated temperatures and chemically reducing condition). - Degradation of engineer barrier components (waste package, waste canister, waste forms, etc.) in a generic salt repository environment (high ionic strength brines, elevated temperatures and chemically reducing condition). - Waste stream types and inventory estimates, particularly for reprocessing high-level waste. (authors)« less

  17. A performance goal-based seismic design philosophy for waste repository facilities

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Hossain, Q.A.

    1994-12-31

    A performance goal-based seismic design philosophy, compatible with DOE`s present natural phenomena hazards mitigation and {open_quotes}graded approach{close_quotes} philosophy, has been proposed for high level nuclear waste repository facilities. The rationale, evolution, and the desirable features of this method have been described. Why and how the method should and can be applied to the design of a repository facility are also discussed.

  18. The Geant4 physics validation repository

    NASA Astrophysics Data System (ADS)

    Wenzel, H.; Yarba, J.; Dotti, A.

    2015-12-01

    The Geant4 collaboration regularly performs validation and regression tests. The results are stored in a central repository and can be easily accessed via a web application. In this article we describe the Geant4 physics validation repository which consists of a relational database storing experimental data and Geant4 test results, a java API and a web application. The functionality of these components and the technology choices we made are also described.

  19. AASG State Geothermal Data Repository for the National Geothermal Data System.

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    2012-01-01

    This Drupal metadata and documents capture and management system is a repository, used for maintenance of metadata which describe resources contributed to the AASG State Geothermal Data System. The repository also provides an archive for files that are not hosted by the agency contributing the resource. Data from all 50 state geological surveys is represented here, and is contributed in turn to the National Geothermal Data System.

  20. Monte Carlo simulations for generic granite repository studies

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Chu, Shaoping; Lee, Joon H; Wang, Yifeng

    In a collaborative study between Los Alamos National Laboratory (LANL) and Sandia National Laboratories (SNL) for the DOE-NE Office of Fuel Cycle Technologies Used Fuel Disposition (UFD) Campaign project, we have conducted preliminary system-level analyses to support the development of a long-term strategy for geologic disposal of high-level radioactive waste. A general modeling framework consisting of a near- and a far-field submodel for a granite GDSE was developed. A representative far-field transport model for a generic granite repository was merged with an integrated systems (GoldSim) near-field model. Integrated Monte Carlo model runs with the combined near- and farfield transport modelsmore » were performed, and the parameter sensitivities were evaluated for the combined system. In addition, a sub-set of radionuclides that are potentially important to repository performance were identified and evaluated for a series of model runs. The analyses were conducted with different waste inventory scenarios. Analyses were also conducted for different repository radionuelide release scenarios. While the results to date are for a generic granite repository, the work establishes the method to be used in the future to provide guidance on the development of strategy for long-term disposal of high-level radioactive waste in a granite repository.« less

  1. Digitizing Dissertations for an Institutional Repository: A Process and Cost Analysis*

    PubMed Central

    Piorun, Mary; Palmer, Lisa A.

    2008-01-01

    Objective: This paper describes the Lamar Soutter Library's process and costs associated with digitizing 300 doctoral dissertations for a newly implemented institutional repository at the University of Massachusetts Medical School. Methodology: Project tasks included identifying metadata elements, obtaining and tracking permissions, converting the dissertations to an electronic format, and coordinating workflow between library departments. Each dissertation was scanned, reviewed for quality control, enhanced with a table of contents, processed through an optical character recognition function, and added to the institutional repository. Results: Three hundred and twenty dissertations were digitized and added to the repository for a cost of $23,562, or $0.28 per page. Seventy-four percent of the authors who were contacted (n = 282) granted permission to digitize their dissertations. Processing time per title was 170 minutes, for a total processing time of 906 hours. In the first 17 months, full-text dissertations in the collection were downloaded 17,555 times. Conclusion: Locally digitizing dissertations or other scholarly works for inclusion in institutional repositories can be cost effective, especially if small, defined projects are chosen. A successful project serves as an excellent recruitment strategy for the institutional repository and helps libraries build new relationships. Challenges include workflow, cost, policy development, and copyright permissions. PMID:18654648

  2. A data-rich recruitment core to support translational clinical research.

    PubMed

    Kost, Rhonda G; Corregano, Lauren M; Rainer, Tyler-Lauren; Melendez, Caroline; Coller, Barry S

    2015-04-01

    Underenrollment of clinical studies wastes resources and delays assessment of research discoveries. We describe the organization and impact of a centralized recruitment core delivering comprehensive recruitment support to investigators. The Rockefeller University Center for Clinical and Translational Science supports a centralized recruitment core, call center, Research Volunteer Repository, data infrastructure, and staff who provide expert recruitment services to investigators. During protocol development, consultations aim to optimize enrollment feasibility, develop recruitment strategy, budget, and advertising. Services during study conduct include advertising placement, repository queries, call management, prescreening, referral, and visit scheduling. Utilization and recruitment outcomes are tracked using dedicated software. For protocols receiving recruitment services during 2009-2013: median time from initiation of recruitment to the first enrolled participant was 10 days; of 4,047 first-time callers to the call center, 92% (n = 3,722) enrolled in the Research Volunteer Repository, with 99% retention; 23% of Repository enrollees subsequently enrolled in ≥1 research studies, with 89% retention. Of volunteers referred by repository queries, 49% (280/537) enrolled into the study, with 92% retained. Provision of robust recruitment infrastructure including expertise, a volunteer repository, data capture and real-time analysis accelerates protocol accrual. Application of recruitment science improves the quality of clinical investigation. © 2014 Wiley Periodicals, Inc.

  3. A perspective on the proliferation risks of plutonium mines

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Lyman, E.S.

    1996-05-01

    The program of geologic disposal of spent fuel and other plutonium-containing materials is increasingly becoming the target of criticism by individuals who argue that in the future, repositories may become low-cost sources of fissile material for nuclear weapons. This paper attempts to outline a consistent framework for analyzing the proliferation risks of these so-called {open_quotes}plutonium mines{close_quotes} and putting them into perspective. First, it is emphasized that the attractiveness of plutonium in a repository as a source of weapons material depends on its accessibility relative to other sources of fissile material. Then, the notion of a {open_quotes}material production standard{close_quotes} (MPS) ismore » proposed: namely, that the proliferation risks posed by geologic disposal will be acceptable if one can demonstrate, under a number of reasonable scenarios, that the recovery of plutonium from a repository is likely to be as difficult as new production of fissile material. A preliminary analysis suggests that the range of circumstances under which current mined repository concepts would fail to meet this standard is fairly narrow. Nevertheless, a broad application of the MPS may impose severe restrictions on repository design. In this context, the relationship of repository design parameters to easy of recovery is discussed.« less

  4. A Data‐Rich Recruitment Core to Support Translational Clinical Research

    PubMed Central

    Corregano, Lauren M.; Rainer, Tyler‐Lauren; Melendez, Caroline; Coller, Barry S.

    2014-01-01

    Abstract Background Underenrollment of clinical studies wastes resources and delays assessment of research discoveries. We describe the organization and impact of a centralized recruitment core delivering comprehensive recruitment support to investigators. Methods The Rockefeller University Center for Clinical and Translational Science supports a centralized recruitment core, call center, Research Volunteer Repository, data infrastructure, and staff who provide expert recruitment services to investigators. During protocol development, consultations aim to optimize enrollment feasibility, develop recruitment strategy, budget, and advertising. Services during study conduct include advertising placement, repository queries, call management, prescreening, referral, and visit scheduling. Utilization and recruitment outcomes are tracked using dedicated software. Results For protocols receiving recruitment services during 2009–2013: median time from initiation of recruitment to the first enrolled participant was 10 days; of 4,047 first‐time callers to the call center, 92% (n = 3,722) enrolled in the Research Volunteer Repository, with 99% retention; 23% of Repository enrollees subsequently enrolled in ≥1 research studies, with 89% retention. Of volunteers referred by repository queries, 49% (280/537) enrolled into the study, with 92% retained. Conclusions Provision of robust recruitment infrastructure including expertise, a volunteer repository, data capture and real‐time analysis accelerates protocol accrual. Application of recruitment science improves the quality of clinical investigation. PMID:25381717

  5. Clone and genomic repositories at the American Type Culture Collection

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Maglott, D.R.; Nierman, W.C.

    1990-01-01

    The American Type Culture Collection (ATCC) has a long history of characterizing, preserving, and distributing biological resource materials for the scientific community. Starting in 1925 as a repository for standard bacterial and fungal strains, its collections have diversified with technologic advances and in response to the requirements of its users. To serve the needs of the human genetics community, the National Institute of Child Health and Human Development (NICHD), National Institutes of Health (NIH), established an international Repository of Human DNA Probes and Libraries at the ATCC in 1985. This repository expanded the existing collections of recombinant clones and librariesmore » at the ATCC, with the specific purposes of (1) obtaining, amplifying, and distribution probes detecting restriction fragment length polymorphisms (RFLPs); (2) obtaining, amplifying, and distributing genomic and cDNA clones from known genes independent of RFLP detection; (3) distributing the chromosome-specific libraries generated by the National Laboratory Gene Library Project at the Lawrence Livermore and Los Alamos National Laboratories and (4) maintaining a public, online database describing the repository materials. Because it was recognized that animal models and comparative mapping can be crucial to genomic characterization, the scope of the repository was broadened in February 1989 to include probes from the mouse genome.« less

  6. A Repository of Codes of Ethics and Technical Standards in Health Informatics

    PubMed Central

    Zaïane, Osmar R.

    2014-01-01

    We present a searchable repository of codes of ethics and standards in health informatics. It is built using state-of-the-art search algorithms and technologies. The repository will be potentially beneficial for public health practitioners, researchers, and software developers in finding and comparing ethics topics of interest. Public health clinics, clinicians, and researchers can use the repository platform as a one-stop reference for various ethics codes and standards. In addition, the repository interface is built for easy navigation, fast search, and side-by-side comparative reading of documents. Our selection criteria for codes and standards are two-fold; firstly, to maintain intellectual property rights, we index only codes and standards freely available on the internet. Secondly, major international, regional, and national health informatics bodies across the globe are surveyed with the aim of understanding the landscape in this domain. We also look at prevalent technical standards in health informatics from major bodies such as the International Standards Organization (ISO) and the U. S. Food and Drug Administration (FDA). Our repository contains codes of ethics from the International Medical Informatics Association (IMIA), the iHealth Coalition (iHC), the American Health Information Management Association (AHIMA), the Australasian College of Health Informatics (ACHI), the British Computer Society (BCS), and the UK Council for Health Informatics Professions (UKCHIP), with room for adding more in the future. Our major contribution is enhancing the findability of codes and standards related to health informatics ethics by compilation and unified access through the health informatics ethics repository. PMID:25422725

  7. Characterization of Heat-treated Clay Minerals in the Context of Nuclear Waste Disposal

    NASA Astrophysics Data System (ADS)

    Matteo, E. N.; Wang, Y.; Kruichak, J. N.; Mills, M. M.

    2015-12-01

    Clay minerals are likely candidates to aid in nuclear waste isolation due to their low permeability, favorable swelling properties, and high cation sorption capacities. Establishing the thermal limit for clay minerals in a nuclear waste repository is a potentially important component of repository design, as flexibility of the heat load within the repository can have a major impact on the selection of repository design. For example, the thermal limit plays a critical role in the time that waste packages would need to cool before being transferred to the repository. Understanding the chemical and physical changes, if any, that occur in clay minerals at various temperatures above the current thermal limit (of 100 °C) can enable decision-makers with information critical to evaluating the potential trade-offs of increasing the thermal limit within the repository. Most critical is gaining understanding of how varying thermal conditions in the repository will impact radionuclide sorption and transport in clay materials either as engineered barriers or as disposal media. A variety of repository-relevant clay minerals (illite, mixed layer illite/smectite, and montmorillonite), were heated for a range of temperatures between 100-1000 °C. These samples were characterized to determine surface area, mineralogical alteration, and cation exchange capacity (CEC). Our results show that for conditions up to 500 °C, no significant change occurs, so long as the clay mineral remains mineralogically intact. At temperatures above 500 °C, transformation of the layered silicates into silica phases leads to alteration that impacts important clay characteristics. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's Nation Nuclear Security Administration under contract DE-AC04-94AL85000. SAND Number: SAND2015-6524 A

  8. An open data repository and a data processing software toolset of an equivalent Nordic grid model matched to historical electricity market data.

    PubMed

    Vanfretti, Luigi; Olsen, Svein H; Arava, V S Narasimham; Laera, Giuseppe; Bidadfar, Ali; Rabuzin, Tin; Jakobsen, Sigurd H; Lavenius, Jan; Baudette, Maxime; Gómez-López, Francisco J

    2017-04-01

    This article presents an open data repository, the methodology to generate it and the associated data processing software developed to consolidate an hourly snapshot historical data set for the year 2015 to an equivalent Nordic power grid model (aka Nordic 44), the consolidation was achieved by matching the model׳s physical response w.r.t historical power flow records in the bidding regions of the Nordic grid that are available from the Nordic electricity market agent, Nord Pool. The model is made available in the form of CIM v14, Modelica and PSS/E (Siemens PTI) files. The Nordic 44 model in Modelica and PSS/E were first presented in the paper titled "iTesla Power Systems Library (iPSL): A Modelica library for phasor time-domain simulations" (Vanfretti et al., 2016) [1] for a single snapshot. In the digital repository being made available with the submission of this paper (SmarTSLab_Nordic44 Repository at Github, 2016) [2], a total of 8760 snapshots (for the year 2015) that can be used to initialize and execute dynamic simulations using tools compatible with CIM v14, the Modelica language and the proprietary PSS/E tool are provided. The Python scripts to generate the snapshots (processed data) are also available with all the data in the GitHub repository (SmarTSLab_Nordic44 Repository at Github, 2016) [2]. This Nordic 44 equivalent model was also used in iTesla project (iTesla) [3] to carry out simulations within a dynamic security assessment toolset (iTesla, 2016) [4], and has been further enhanced during the ITEA3 OpenCPS project (iTEA3) [5]. The raw, processed data and output models utilized within the iTesla platform (iTesla, 2016) [4] are also available in the repository. The CIM and Modelica snapshots of the "Nordic 44" model for the year 2015 are available in a Zenodo repository.

  9. Geohydrologic aspects for siting and design of low-level radioactive-waste disposal

    USGS Publications Warehouse

    Bedinger, M.S.

    1989-01-01

    The objective for siting and design of low-level radioactive-waste repository sites is to isolate the waste from the biosphere until the waste no longer poses an unacceptable hazard as a result of radioactive decay. Low-level radioactive waste commonly is isolated at shallow depths with various engineered features to stabilize the waste and to reduce its dissolution and transport by ground water. The unsaturated zone generally is preferred for isolating the waste. Low-level radioactive waste may need to be isolated for 300 to 500 years. Maintenance and monitoring of the repository site are required by Federal regulations for only the first 100 years. Therefore, geohydrology of the repository site needs to provide natural isolation of the waste for the hazardous period following maintenance of the site. Engineering design of the repository needs to be compatible with the natural geohydrologic conditions at the site. Studies at existing commercial and Federal waste-disposal sites provide information on the problems encountered and the basis for establishing siting guidelines for improved isolation of radioactive waste, engineering design of repository structures, and surveillance needs to assess the effectiveness of the repositories and to provide early warning of problems that may require remedial action.Climate directly affects the hydrology of a site and probably is the most important single factor that affects the suitability of a site for shallow-land burial of low-level radioactive waste. Humid and subhumid regions are not well suited for shallow isolation of low-level radioactive waste in the unsaturated zone; arid regions with zero to small infiltration from precipitation, great depths to the water table, and long flow paths to natural discharge areas are naturally well suited to isolation of the waste. The unsaturated zone is preferred for isolation of low-level radioactive waste. The guiding rationale is to minimize contact of water with the waste and to minimize transport of waste from the repository. The hydrology of a flow system containing a repository is greatly affected by the engineering of the repository site. Prediction of the performance of the repository is a complex problem, hampered by problems of characterizing the natural and manmade features of the flow system and by the limitations of models to predict flow and geochemical processes in the saturated and unsaturated zones. Disposal in low-permeability unfractured clays in the saturated zone may be feasible where the radionuclide transport is controlled by diffusion rather than advection.

  10. A review of the organic geochemistry of shales

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Ho, P.C.; Meyer, R.E.

    1987-06-01

    Shale formations have been suggested as a potential site for a high level nuclear waste repository. As a first step in the study of the possible interaction of nuclides with the organic components of the shales, literature on the identification of organic compounds from various shales of the continent of the United States has been reviewed. The Green River shale of the Cenozoic era is the most studied shale followed by the Pierre shale of the Mesozoic era and the Devonian black shale of the Paleozoic era. Organic compounds that have been identified from these shales are hydrocarbons, fatty acids,more » fatty alcohols, steranes, terpanes, carotenes, carbohydrates, amino acids, and porphyrins. However, these organic compounds constitute only a small fraction of the organics in shales and the majority of the organic compounds in shales are still unidentified.« less

  11. Description of five species of Xanthopimpla Saussure 1892 (Hymenoptera: Ichneumonidae: Pimplinae) from Malaysia

    NASA Astrophysics Data System (ADS)

    Dass, Angeline David; Ghani, Idris Abd.

    2013-11-01

    Description of five species of Xanthopimpla Saussure, 1829 (Hymenoptera: Ichneumonidae: Pimplinae) from Malaysia was done using specimens deposited in Centre for Insects Systematics, Universiti Kebangsaan Malaysia (CIS, UKM). Type and non-type specimens were loaned from several repositories namely Zoological Museum of Amsterdam Netherlands (ZMAN), Swedish Museum of Natural History (NRM), British Natural History Museum London (BMNH) and Department of Agricultural Malaysia (DOA) for identification and comparison. The specimens were identified to the species level which gives rise to five species namely Xanthopimpla conica Cushman, 1925, Xanthopimpla despinosa leipephelis Townes & Chiu, 1970, Xanthopimpla flavolineata Cameron, 1907, Xanthopimpla punctata (Fabricius, 1781) and Xanthopimpla tricapus impressa Townes & Chiu, 1970. A dichotomous key and descriptions for five Xanthopimpla spesies were provided. Photos and illustrations of carina on propodeum were also included in this paper.

  12. Automated Rocket Propulsion Test Management

    NASA Technical Reports Server (NTRS)

    Walters, Ian; Nelson, Cheryl; Jones, Helene

    2007-01-01

    The Rocket Propulsion Test-Automated Management System provides a central location for managing activities associated with Rocket Propulsion Test Management Board, National Rocket Propulsion Test Alliance, and the Senior Steering Group business management activities. A set of authorized users, both on-site and off-site with regard to Stennis Space Center (SSC), can access the system through a Web interface. Web-based forms are used for user input with generation and electronic distribution of reports easily accessible. Major functions managed by this software include meeting agenda management, meeting minutes, action requests, action items, directives, and recommendations. Additional functions include electronic review, approval, and signatures. A repository/library of documents is available for users, and all items are tracked in the system by unique identification numbers and status (open, closed, percent complete, etc.). The system also provides queries and version control for input of all items.

  13. 76 FR 57644 - Privacy Act of 1974; Implementation

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-09-16

    ... in DMDC 13, entitled ``Investigative Records Repository'', when investigatory material is compiled... exemptions. * * * * * (c) * * * (17) System identifier and name: DMDC 13, Investigative Records Repository...

  14. Stem Cell Therapy to Improve Burn Wound Healing

    DTIC Science & Technology

    2017-03-01

    Aim(s) • Perform Phase 1 Trial of Allogeneic MSCs in Burns • Perform Phase 2 Trial of Allogeneic MSCs in Burns • Collect Tissue Repository for...for safety/dose studies CY15 Goal – Continue Phase 1 and, Start Tissue Repository  Continue donors recruitment, screening and Bone Marrow Aspiration...1 Trial and Collect Tissue Repository  Continue donors recruitment, screening and Bone Marrow Aspiration as needed.  Continue patients screening

  15. Army Hearing Program Talking Points Calendar Year 2015

    DTIC Science & Technology

    2016-12-14

    outside the range of normal hearing sensitivity (greater than 25 dB), CY15 data.  Data: DOEHRS-HC Data Repository , Soldiers who had a DD2215 or...1.  Data: Defense Occupational and Environmental Health Readiness System-Hearing Conservation (DOEHRS-HC) Data Repository , CY15—Army Profile...Soldiers have a hearing loss that required a fit-for-duty (Readiness) evaluation:  An H-3 Hearing Profile.  Data: DOEHRS-HC Data Repository

  16. The Geant4 physics validation repository

    DOE PAGES

    Wenzel, H.; Yarba, J.; Dotti, A.

    2015-12-23

    The Geant4 collaboration regularly performs validation and regression tests. The results are stored in a central repository and can be easily accessed via a web application. In this article we describe the Geant4 physics validation repository which consists of a relational database storing experimental data and Geant4 test results, a java API and a web application. Lastly, the functionality of these components and the technology choices we made are also described

  17. Environmental protection problems in the vicinity of the Zelazny most flotation wastes depository in Poland.

    PubMed

    Lasocki, Stanislaw; Antoniuk, Janusz; Moscicki, Jerzy

    2003-08-01

    The Zelazny Most depository of wastes from copper-ore processing, located in southwest Poland, is the largest mineral wastes repository in Europe. Moreover, it is located in a seismically active area. The seismicity is induced and is connected with mining works in the nearby underground copper mines. Any release of the contents of the repository to the environment could have devastating and even catastrophic consequences. For this reason, geophysical methods are used for continuous monitoring the state of the repository containment dams. The article presents examples of the application of geoelectric methods for detecting sites of leakage of contaminated water and a sketch of the seismic hazard analysis, which was used to predict future seismic vibrations of the repository dams.

  18. YUCCA MOUNTAIN PROJECT - A BRIEFING --

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    NA

    2003-08-05

    This report has the following articles: Nuclear waste--a long-term national problem; Spent nuclear fuel; High-level radioactive waste; Radioactivity and the environment; Current storage methods; Disposal options; U.S. policy on nuclear waste; The focus on Yucca Mountain; The purpose and scope of the Yucca Mountain Project; The approach for permanently disposing of waste; The scientific studies at Yucca Mountain; The proposed design for a repository at Yucca Mountain; Natural and engineered barriers would work together to isolate waste; Meticulous science and technology to protect people and the environment; Licensing a repository; Transporting waste to a permanent repository; The Environmental Impact Statementmore » for a repository; Current status of the Yucca Mountain Project; and Further information available on the Internet.« less

  19. Mining Hierarchies and Similarity Clusters from Value Set Repositories.

    PubMed

    Peterson, Kevin J; Jiang, Guoqian; Brue, Scott M; Shen, Feichen; Liu, Hongfang

    2017-01-01

    A value set is a collection of permissible values used to describe a specific conceptual domain for a given purpose. By helping to establish a shared semantic understanding across use cases, these artifacts are important enablers of interoperability and data standardization. As the size of repositories cataloging these value sets expand, knowledge management challenges become more pronounced. Specifically, discovering value sets applicable to a given use case may be challenging in a large repository. In this study, we describe methods to extract implicit relationships between value sets, and utilize these relationships to overlay organizational structure onto value set repositories. We successfully extract two different structurings, hierarchy and clustering, and show how tooling can leverage these structures to enable more effective value set discovery.

  20. DOE Office of Scientific and Technical Information (OSTI.GOV)

    Huff, Kathryn D.

    Component level and system level abstraction of detailed computational geologic repository models have resulted in four rapid computational models of hydrologic radionuclide transport at varying levels of detail. Those models are described, as is their implementation in Cyder, a software library of interchangeable radionuclide transport models appropriate for representing natural and engineered barrier components of generic geology repository concepts. A proof of principle demonstration was also conducted in which these models were used to represent the natural and engineered barrier components of a repository concept in a reducing, homogenous, generic geology. This base case demonstrates integration of the Cyder openmore » source library with the Cyclus computational fuel cycle systems analysis platform to facilitate calculation of repository performance metrics with respect to fuel cycle choices. (authors)« less

  1. 77 FR 15587 - Privacy Act of 1974; Implementation

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-03-16

    ... in DMDC 11, entitled ``Investigative Records Repository'', when investigatory material is compiled... Records Repository. (i) Exemptions: (A) Investigatory material compiled for law enforcement purposes may...

  2. DOE Office of Scientific and Technical Information (OSTI.GOV)

    Krier, D. J.; Perry, F. V.

    Location, timing, volume, and eruptive style of post-Miocene volcanoes have defined the volcanic hazard significant to a proposed high-level radioactive waste (HLW) and spent nuclear fuel (SNF) repository at Yucca Mountain, Nevada, as a low-probability, high-consequence event. Examination of eruptive centers in the region that may be analogueues to possible future volcanic activity at Yucca Mountain have aided in defining and evaluating the consequence scenarios for intrusion into and eruption above a repository. The probability of a future event intersecting a repository at Yucca Mountain has a mean value of 1.7 x 10{sup -8} per year. This probability comes frommore » the Probabilistic Volcanic Hazard Assessment (PVHA) completed in 1996 and updated to reflect change in repository layout. Since that time, magnetic anomalies representing potential buried volcanic centers have been identified fiom magnetic surveys; however these potential buried centers only slightly increase the probability of an event intersecting the repository. The proposed repository will be located in its central portion of Yucca Mountain at approximately 300m depth. The process for assessing performance of a repository at Yucca Mountain has identified two scenarios for igneous activity that, although having a very low probability of occurrence, could have a significant consequence should an igneous event occur. Either a dike swarm intersecting repository drifts containing waste packages, or a volcanic eruption through the repository could result in release of radioactive material to the accessible environment. Ongoing investigations are assessing the mechanisms and significance of the consequence scenarios. Lathrop Wells Cone ({approx}80,000 yrs), a key analogue for estimating potential future volcanic activity, is the youngest surface expression of apparent waning basaltic volcanism in the region. Cone internal structure, lavas, and ash-fall tephra have been examined to estimate eruptive volume, eruption type, and subsurface disturbance accompanying conduit growth and eruption. The Lathrop Wells volcanic complex has a total volume estimate of approximately 0.1 km{sup 3}. The eruptive products indicate a sequence of initial magmatic fissure fountaining, early Strombolian activity, and a brief hydrovolcanic phase, and violent Strombolian phase(s). Lava flows adjacent to the Lathrop Wells Cone probably were emplaced during the mid-eruptive sequence. Ongoing investigations continue to address the potential hazards of a volcanic event at Yucca Mountain.« less

  3. 10 CFR 960.5-2-8 - Surface characteristics.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... NUCLEAR WASTE REPOSITORY Preclosure Guidelines Ease and Cost of Siting, Construction, Operation, and... repository siting, construction, operation, and closure. (b) Favorable conditions. (1) Generally flat terrain...

  4. 10 CFR 960.5-2-8 - Surface characteristics.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... NUCLEAR WASTE REPOSITORY Preclosure Guidelines Ease and Cost of Siting, Construction, Operation, and... repository siting, construction, operation, and closure. (b) Favorable conditions. (1) Generally flat terrain...

  5. 10 CFR 960.5-2-8 - Surface characteristics.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... NUCLEAR WASTE REPOSITORY Preclosure Guidelines Ease and Cost of Siting, Construction, Operation, and... repository siting, construction, operation, and closure. (b) Favorable conditions. (1) Generally flat terrain...

  6. 10 CFR 960.5-2-8 - Surface characteristics.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... NUCLEAR WASTE REPOSITORY Preclosure Guidelines Ease and Cost of Siting, Construction, Operation, and... repository siting, construction, operation, and closure. (b) Favorable conditions. (1) Generally flat terrain...

  7. Final repository for Denmark's low- and intermediate level radioactive waste

    NASA Astrophysics Data System (ADS)

    Nilsson, B.; Gravesen, P.; Petersen, S. S.; Binderup, M.

    2012-12-01

    Bertel Nilsson*, Peter Gravesen, Stig A. Schack Petersen, Merete Binderup Geological Survey of Denmark and Greenland (GEUS), Øster Voldgade 10, 1350 Copenhagen, Denmark, * email address bn@geus.dk The Danish Parliament decided in 2003 that the temporal disposal of the low- and intermediate level radioactive waste at the nuclear facilities at Risø should find another location for a final repository. The Danish radioactive waste must be stored on Danish land territory (exclusive Greenland) and must hold the entire existing radioactive waste, consisting of the waste from the decommissioning of the nuclear facilities at Risø, and the radioactive waste produced in Denmark from hospitals, universities and industry. The radioactive waste is estimated to a total amount of up to 10,000 m3. The Geological Survey of Denmark and Greenland, GEUS, is responsible for the geological studies of suitable areas for the repository. The task has been to locate and recognize non-fractured Quaternary and Tertiary clays or Precambrian bedrocks with low permeability which can isolate the radioactive waste from the surroundings the coming more than 300 years. Twenty two potential areas have been located and sequential reduced to the most favorable two to three locations taking into consideration geology, hydrogeology, nature protection and climate change conditions. Further detailed environmental and geology investigations will be undertaken at the two to three potential localities in 2013 to 2015. This study together with a study of safe transport of the radioactive waste and an investigation of appropriate repository concepts in relation to geology and safety analyses will constitute the basis upon which the final decision by the Danish Parliament on repository concept and repository location. The final repository is planned to be established and in operation at the earliest 2020.

  8. Implementation of the Brazilian National Repository - RBMN Project - 13008

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Cassia Oliveira de Tello, Cledola

    2013-07-01

    Ionizing radiation in Brazil is used in electricity generation, medicine, industry, agriculture and for research and development purposes. All these activities can generate radioactive waste. At this point, in Brazil, the use of nuclear energy and radioisotopes justifies the construction of a national repository for radioactive wastes of low and intermediate-level. According to Federal Law No. 10308, Brazilian National Commission for Nuclear Energy (CNEN) is responsible for designing and constructing the intermediate and final storages for radioactive wastes. Additionally, a restriction on the construction of Angra 3 is that the repository is under construction until its operation start, attaining somemore » requirements of the Brazilian Environmental Regulator (IBAMA). Besides this NPP, in the National Energy Program is previewed the installation of four more plants, by 2030. In November 2008, CNEN launched the Project RBMN (Repository for Low and Intermediate-Level Radioactive Wastes), which aims at the implantation of a National Repository for disposal of low and intermediate-level of radiation wastes. This Project has some aspects that are unique in the Brazilian context, especially referring to the time between its construction and the end of its institutional period. This time is about 360 years, when the area will be released for unrestricted uses. It means that the Repository must be safe and secure for more than three hundred years, which is longer than half of the whole of Brazilian history. This aspect is very new for the Brazilian people, bringing a new dimension to public acceptance. Another point is this will be the first repository in South America, bringing a real challenge for the continent. The current status of the Project is summarized. (authors)« less

  9. Temperature-package power correlations for open-mode geologic disposal concepts.

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Hardin, Ernest.

    2013-02-01

    Logistical simulation of spent nuclear fuel (SNF) management in the U.S. combines storage, transportation and disposal elements to evaluate schedule, cost and other resources needed for all major operations leading to final geologic disposal. Geologic repository reference options are associated with limits on waste package thermal power output at emplacement, in order to meet limits on peak temperature for certain key engineered and natural barriers. These package power limits are used in logistical simulation software such as CALVIN, as threshold requirements that must be met by means of decay storage or SNF blending in waste packages, before emplacement in amore » repository. Geologic repository reference options include enclosed modes developed for crystalline rock, clay or shale, and salt. In addition, a further need has been addressed for open modes in which SNF can be emplaced in a repository, then ventilated for decades or longer to remove heat, prior to permanent repository closure. For each open mode disposal concept there are specified durations for surface decay storage (prior to emplacement), repository ventilation, and repository closure operations. This study simulates those steps for several timing cases, and for SNF with three fuel-burnup characteristics, to develop package power limits at which waste packages can be emplaced without exceeding specified temperature limits many years later after permanent closure. The results are presented in the form of correlations that span a range of package power and peak postclosure temperature, for each open-mode disposal concept, and for each timing case. Given a particular temperature limit value, the corresponding package power limit for each case can be selected for use in CALVIN and similar tools.« less

  10. Evaluation of Groundwater Pathways and Travel Times From the Nevada Test Site to the Potential Yucca Mountain Repository

    NASA Astrophysics Data System (ADS)

    Pohlmann, K. F.; Zhu, J.; Ye, M.; Carroll, R. W.; Chapman, J. B.; Russell, C. E.; Shafer, D. S.

    2006-12-01

    Yucca Mountain (YM), Nevada has been recommended as a deep geological repository for the disposal of spent fuel and high-level radioactive waste. If YM is licensed as a repository by the Nuclear Regulatory Commission, it will be important to identify the potential for radionuclides to migrate from underground nuclear testing areas located on the Nevada Test Site (NTS) to the hydraulically downgradient repository area to ensure that monitoring does not incorrectly attribute repository failure to radionuclides originating from other sources. In this study, we use the Death Valley Regional Flow System (DVRFS) model developed by the U.S. Geological Survey to investigate potential groundwater migration pathways and associated travel times from the NTS to the proposed YM repository area. Using results from the calibrated DVRFS model and the particle tracking post-processing package MODPATH we modeled three-dimensional groundwater advective pathways in the NTS and YM region. Our study focuses on evaluating the potential for groundwater pathways between the NTS and YM withdrawal area and whether travel times for advective flow along these pathways coincide with the prospective monitoring time frame at the proposed repository. We include uncertainty in effective porosity as this is a critical variable in the determination of time for radionuclides to travel from the NTS region to the YM withdrawal area. Uncertainty in porosity is quantified through evaluation of existing site data and expert judgment and is incorporated in the model through Monte Carlo simulation. Since porosity information is limited for this region, the uncertainty is quite large and this is reflected in the results as a large range in simulated groundwater travel times.

  11. DOE Office of Scientific and Technical Information (OSTI.GOV)

    Harmon, K.M.; Lakey, L.T.; Leigh, I.W.

    Worldwide activities related to nuclear fuel cycle and radioactive waste management programs are summarized. Several trends have developed in waste management strategy: All countries having to dispose of reprocessing wastes plan on conversion of the high-level waste (HLW) stream to a borosilicate glass and eventual emplacement of the glass logs, suitably packaged, in a deep geologic repository. Countries that must deal with plutonium-contaminated waste emphasize pluonium recovery, volume reduction and fixation in cement or bitumen in their treatment plans and expect to use deep geologic repositories for final disposal. Commercially available, classical engineering processing are being used worldwide to treatmore » and immobilize low- and intermediate-level wastes (LLW, ILW); disposal to surface structures, shallow-land burial and deep-underground repositories, such as played-out mines, is being done widely with no obvious technical problems. Many countries have established extensive programs to prepare for construction and operation of geologic repositories. Geologic media being studied fall into three main classes: argillites (clay or shale); crystalline rock (granite, basalt, gneiss or gabbro); and evaporates (salt formations). Most nations plan to allow 30 years or longer between discharge of fuel from the reactor and emplacement of HLW or spent fuel is a repository to permit thermal and radioactive decay. Most repository designs are based on the mined-gallery concept, placing waste or spent fuel packages into shallow holes in the floor of the gallery. Many countries have established extensive and costly programs of site evaluation, repository development and safety assessment. Two other waste management problems are the subject of major R and D programs in several countries: stabilization of uranium mill tailing piles; and immobilization or disposal of contaminated nuclear facilities, namely reactors, fuel cycle plants and R and D laboratories.« less

  12. Radioactive waste isolation in salt: special advisory report on the status of the Office of Nuclear Waste Isolation's plans for repository performance assessment

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Ditmars, J.D.; Walbridge, E.W.; Rote, D.M.

    1983-10-01

    Repository performance assessment is analysis that identifies events and processes that might affect a repository system for isolation of radioactive waste, examines their effects on barriers to waste migration, and estimates the probabilities of their occurrence and their consequences. In 1983 Battelle Memorial Institute's Office of Nuclear Waste Isolation (ONWI) prepared two plans - one for performance assessment for a waste repository in salt and one for verification and validation of performance assessment technology. At the request of the US Department of Energy's Salt Repository Project Office (SRPO), Argonne National Laboratory reviewed those plans and prepared this report to advisemore » SRPO of specific areas where ONWI's plans for performance assessment might be improved. This report presents a framework for repository performance assessment that clearly identifies the relationships among the disposal problems, the processes underlying the problems, the tools for assessment (computer codes), and the data. In particular, the relationships among important processes and 26 model codes available to ONWI are indicated. A common suggestion for computer code verification and validation is the need for specific and unambiguous documentation of the results of performance assessment activities. A major portion of this report consists of status summaries of 27 model codes indicated as potentially useful by ONWI. The code summaries focus on three main areas: (1) the code's purpose, capabilities, and limitations; (2) status of the elements of documentation and review essential for code verification and validation; and (3) proposed application of the code for performance assessment of salt repository systems. 15 references, 6 figures, 4 tables.« less

  13. DOE Office of Scientific and Technical Information (OSTI.GOV)

    F. Perry; R. Youngs

    The purpose of this scientific analysis report is threefold: (1) Present a conceptual framework of igneous activity in the Yucca Mountain region (YMR) consistent with the volcanic and tectonic history of this region and the assessment of this history by experts who participated in the probabilistic volcanic hazard analysis (PVHA) (CRWMS M&O 1996 [DIRS 100116]). Conceptual models presented in the PVHA are summarized and applied in areas in which new information has been presented. Alternative conceptual models are discussed, as well as their impact on probability models. The relationship between volcanic source zones defined in the PVHA and structural featuresmore » of the YMR are described based on discussions in the PVHA and studies presented since the PVHA. (2) Present revised probability calculations based on PVHA outputs for a repository footprint proposed in 2003 (BSC 2003 [DIRS 162289]), rather than the footprint used at the time of the PVHA. This analysis report also calculates the probability of an eruptive center(s) forming within the repository footprint using information developed in the PVHA. Probability distributions are presented for the length and orientation of volcanic dikes located within the repository footprint and for the number of eruptive centers (conditional on a dike intersecting the repository) located within the repository footprint. (3) Document sensitivity studies that analyze how the presence of potentially buried basaltic volcanoes may affect the computed frequency of intersection of the repository footprint by a basaltic dike. These sensitivity studies are prompted by aeromagnetic data collected in 1999, indicating the possible presence of previously unrecognized buried volcanoes in the YMR (Blakely et al. 2000 [DIRS 151881]; O'Leary et al. 2002 [DIRS 158468]). The results of the sensitivity studies are for informational purposes only and are not to be used for purposes of assessing repository performance.« less

  14. Coupled Multi-physical Simulations for the Assessment of Nuclear Waste Repository Concepts: Modeling, Software Development and Simulation

    NASA Astrophysics Data System (ADS)

    Massmann, J.; Nagel, T.; Bilke, L.; Böttcher, N.; Heusermann, S.; Fischer, T.; Kumar, V.; Schäfers, A.; Shao, H.; Vogel, P.; Wang, W.; Watanabe, N.; Ziefle, G.; Kolditz, O.

    2016-12-01

    As part of the German site selection process for a high-level nuclear waste repository, different repository concepts in the geological candidate formations rock salt, clay stone and crystalline rock are being discussed. An open assessment of these concepts using numerical simulations requires physical models capturing the individual particularities of each rock type and associated geotechnical barrier concept to a comparable level of sophistication. In a joint work group of the Helmholtz Centre for Environmental Research (UFZ) and the German Federal Institute for Geosciences and Natural Resources (BGR), scientists of the UFZ are developing and implementing multiphysical process models while BGR scientists apply them to large scale analyses. The advances in simulation methods for waste repositories are incorporated into the open-source code OpenGeoSys. Here, recent application-driven progress in this context is highlighted. A robust implementation of visco-plasticity with temperature-dependent properties into a framework for the thermo-mechanical analysis of rock salt will be shown. The model enables the simulation of heat transport along with its consequences on the elastic response as well as on primary and secondary creep or the occurrence of dilatancy in the repository near field. Transverse isotropy, non-isothermal hydraulic processes and their coupling to mechanical stresses are taken into account for the analysis of repositories in clay stone. These processes are also considered in the near field analyses of engineered barrier systems, including the swelling/shrinkage of the bentonite material. The temperature-dependent saturation evolution around the heat-emitting waste container is described by different multiphase flow formulations. For all mentioned applications, we illustrate the workflow from model development and implementation, over verification and validation, to repository-scale application simulations using methods of high performance computing.

  15. A metadata-driven approach to data repository design.

    PubMed

    Harvey, Matthew J; McLean, Andrew; Rzepa, Henry S

    2017-01-01

    The design and use of a metadata-driven data repository for research data management is described. Metadata is collected automatically during the submission process whenever possible and is registered with DataCite in accordance with their current metadata schema, in exchange for a persistent digital object identifier. Two examples of data preview are illustrated, including the demonstration of a method for integration with commercial software that confers rich domain-specific data analytics without introducing customisation into the repository itself.

  16. The National Institute of Diabetes and Digestive and Kidney Diseases Central Repositories: A Valuable Resource for Nephrology Research

    PubMed Central

    Akolkar, Beena; Spain, Lisa M.; Guill, Michael H.; Del Vecchio, Corey T.; Carroll, Leslie E.

    2015-01-01

    The National Institute of Diabetes and Digestive and Kidney Diseases (NIDDK) Central Repositories, part of the National Institutes of Health (NIH), are an important resource available to researchers and the general public. The Central Repositories house samples, genetic data, phenotypic data, and study documentation from >100 NIDDK-funded clinical studies, in areas such as diabetes, digestive disease, and liver disease research. The Central Repositories also have an exceptionally rich collection of studies related to kidney disease, including the Modification of Diet in Renal Disease landmark study and recent data from the Chronic Renal Insufficiency Cohort and CKD in Children Cohort studies. The data are carefully curated and linked to the samples from the study. The NIDDK is working to make the materials and data accessible to researchers. The Data Repositories continue to improve flexible online searching tools that help researchers identify the samples or data of interest, and NIDDK has created several different paths to access the data and samples, including some funding initiatives. Over the past several years, the Central Repositories have seen steadily increasing interest and use of the stored materials. NIDDK plans to make more collections available and do more outreach and education about use of the datasets to the nephrology research community in the future to enhance the value of this resource. PMID:25376765

  17. The National Institute of Diabetes and Digestive and Kidney Diseases Central Repositories: a valuable resource for nephrology research.

    PubMed

    Rasooly, Rebekah S; Akolkar, Beena; Spain, Lisa M; Guill, Michael H; Del Vecchio, Corey T; Carroll, Leslie E

    2015-04-07

    The National Institute of Diabetes and Digestive and Kidney Diseases (NIDDK) Central Repositories, part of the National Institutes of Health (NIH), are an important resource available to researchers and the general public. The Central Repositories house samples, genetic data, phenotypic data, and study documentation from >100 NIDDK-funded clinical studies, in areas such as diabetes, digestive disease, and liver disease research. The Central Repositories also have an exceptionally rich collection of studies related to kidney disease, including the Modification of Diet in Renal Disease landmark study and recent data from the Chronic Renal Insufficiency Cohort and CKD in Children Cohort studies. The data are carefully curated and linked to the samples from the study. The NIDDK is working to make the materials and data accessible to researchers. The Data Repositories continue to improve flexible online searching tools that help researchers identify the samples or data of interest, and NIDDK has created several different paths to access the data and samples, including some funding initiatives. Over the past several years, the Central Repositories have seen steadily increasing interest and use of the stored materials. NIDDK plans to make more collections available and do more outreach and education about use of the datasets to the nephrology research community in the future to enhance the value of this resource. Copyright © 2015 by the American Society of Nephrology.

  18. Proceedings of the scientific visit on crystalline rock repository development.

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Mariner, Paul E.; Hardin, Ernest L.; Miksova, Jitka

    2013-02-01

    A scientific visit on Crystalline Rock Repository Development was held in the Czech Republic on September 24-27, 2012. The visit was hosted by the Czech Radioactive Waste Repository Authority (RAWRA), co-hosted by Sandia National Laboratories (SNL), and supported by the International Atomic Energy Agency (IAEA). The purpose of the visit was to promote technical information exchange between participants from countries engaged in the investigation and exploration of crystalline rock for the eventual construction of nuclear waste repositories. The visit was designed especially for participants of countries that have recently commenced (or recommenced) national repository programmes in crystalline host rock formations.more » Discussion topics included repository programme development, site screening and selection, site characterization, disposal concepts in crystalline host rock, regulatory frameworks, and safety assessment methodology. Interest was surveyed in establishing a %E2%80%9Cclub,%E2%80%9D the mission of which would be to identify and address the various technical challenges that confront the disposal of radioactive waste in crystalline rock environments. The idea of a second scientific visit to be held one year later in another host country received popular support. The visit concluded with a trip to the countryside south of Prague where participants were treated to a tour of the laboratory and underground facilities of the Josef Regional Underground Research Centre.« less

  19. Logistics Modeling of Emplacement Rate and Duration of Operations for Generic Geologic Repository Concepts

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Kalinina, Elena Arkadievna; Hardin, Ernest

    This study identified potential geologic repository concepts for disposal of spent nuclear fuel (SNF) and (2) evaluated the achievable repository waste emplacement rate and the time required to complete the disposal for these concepts. Total repository capacity is assumed to be approximately 140,000 MT of spent fuel. The results of this study provide an important input for the rough-order-of-magnitude (ROM) disposal cost analysis. The disposal concepts cover three major categories of host geologic media: crystalline or hard rock, salt, and argillaceous rock. Four waste package sizes are considered: 4PWR/9BWR; 12PWR/21BWR; 21PWR/44BWR, and dual purpose canisters (DPCs). The DPC concepts assumemore » that the existing canisters will be sealed into disposal overpacks for direct disposal. Each concept assumes one of the following emplacement power limits for either emplacement or repository closure: 1.7 kW; 2.2 kW; 5.5 kW; 10 kW; 11.5 kW, and 18 kW.« less

  20. The FLEXGene repository: exploiting the fruits of the genome projects by creating a needed resource to face the challenges of the post-genomic era.

    PubMed

    Brizuela, Leonardo; Richardson, Aaron; Marsischky, Gerald; Labaer, Joshua

    2002-01-01

    Thanks to the results of the multiple completed and ongoing genome sequencing projects and to the newly available recombination-based cloning techniques, it is now possible to build gene repositories with no precedent in their composition, formatting, and potential. This new type of gene repository is necessary to address the challenges imposed by the post-genomic era, i.e., experimentation on a genome-wide scale. We are building the FLEXGene (Full Length EXpression-ready) repository. This unique resource will contain clones representing the complete ORFeome of different organisms, including Homo sapiens as well as several pathogens and model organisms. It will consist of a comprehensive, characterized (sequence-verified), and arrayed gene repository. This resource will allow full exploitation of the genomic information by enabling genome-wide scale experimentation at the level of functional/phenotypic assays as well as at the level of protein expression, purification, and analysis. Here we describe the rationale and construction of this resource and focus on the data obtained from the Saccharomyces cerevisiae project.

  1. Adapting a Clinical Data Repository to ICD-10-CM through the use of a Terminology Repository

    PubMed Central

    Cimino, James J.; Remennick, Lyubov

    2014-01-01

    Clinical data repositories frequently contain patient diagnoses coded with the International Classification of Diseases, Ninth Revision (ICD-9-CM). These repositories now need to accommodate data coded with the Tenth Revision (ICD-10-CM). Database users wish to retrieve relevant data regardless of the system by which they are coded. We demonstrate how a terminology repository (the Research Entities Dictionary or RED) serves as an ontology relating terms of both ICD versions to each other to support seamless version-independent retrieval from the Biomedical Translational Research Information System (BTRIS) at the National Institutes of Health. We make use of the Center for Medicare and Medicaid Services’ General Equivalence Mappings (GEMs) to reduce the modeling effort required to determine whether ICD-10-CM terms should be added to the RED as new concepts or as synonyms of existing concepts. A divide-and-conquer approach is used to develop integration heuristics that offer a satisfactory interim solution and facilitate additional refinement of the integration as time and resources allow. PMID:25954344

  2. Childhood Vesicoureteral Reflux Studies: Registries and Repositories Sources and Nosology

    PubMed Central

    Chesney, Russell W.; Patters, Andrea B.

    2012-01-01

    Despite several recent studies, the advisability of antimicrobial prophylaxis and certain imaging studies for urinary tract infections (UTIs) remains controversial. The role of vesicoureteral reflux (VUR) on the severity and re-infection rates for UTIs is also difficult to assess. Registries and repositories of data and biomaterials from clinical studies in children with VUR are valuable. Disease registries are collections of secondary data related to patients with a specific diagnosis, condition or procedure. Registries differ from indices in that they contain more extensive data. A research repository is an entity that receives, stores, processes and/or disseminates specimens (or other materials) as needed. It encompasses the physical location as well as the full range of activities associated with its operation. It may also be referred to as a biorepository. This report provides information about some current registries and repositories that include data and samples from children with VUR. It also describes the heterogeneous nature of the subjects, as some registries and repositories include only data or samples from patients with primary reflux while others also include those from patients with syndromic or secondary reflux. PMID:23044377

  3. Legal Agreements and the Governance of Research Commons: Lessons from Materials Sharing in Mouse Genomics

    PubMed Central

    Mishra, Amrita

    2014-01-01

    Abstract Omics research infrastructure such as databases and bio-repositories requires effective governance to support pre-competitive research. Governance includes the use of legal agreements, such as Material Transfer Agreements (MTAs). We analyze the use of such agreements in the mouse research commons, including by two large-scale resource development projects: the International Knockout Mouse Consortium (IKMC) and International Mouse Phenotyping Consortium (IMPC). We combine an analysis of legal agreements and semi-structured interviews with 87 members of the mouse model research community to examine legal agreements in four contexts: (1) between researchers; (2) deposit into repositories; (3) distribution by repositories; and (4) exchanges between repositories, especially those that are consortium members of the IKMC and IMPC. We conclude that legal agreements for the deposit and distribution of research reagents should be kept as simple and standard as possible, especially when minimal enforcement capacity and resources exist. Simple and standardized legal agreements reduce transactional bottlenecks and facilitate the creation of a vibrant and sustainable research commons, supported by repositories and databases. PMID:24552652

  4. Audit and Certification Process for Science Data Digital Repositories

    NASA Astrophysics Data System (ADS)

    Hughes, J. S.; Giaretta, D.; Ambacher, B.; Ashley, K.; Conrad, M.; Downs, R. R.; Garrett, J.; Guercio, M.; Lambert, S.; Longstreth, T.; Sawyer, D. M.; Sierman, B.; Tibbo, H.; Waltz, M.

    2011-12-01

    Science data digital repositories are entrusted to ensure that a science community's data are available and useful to users both today and in the future. Part of the challenge in meeting this responsibility is identifying the standards, policies and procedures required to accomplish effective data preservation. Subsequently a repository should be evaluated on whether or not they are effective in their data preservation efforts. This poster will outline the process by which digital repositories are being formally evaluated in terms of their ability to preserve the digitally encoded information with which they have been entrusted. The ISO standards on which this is based will be identified and the relationship of these standards to the Open Archive Information System (OAIS) reference model will be shown. Six test audits have been conducted with three repositories in Europe and three in the USA. Some of the major lessons learned from these test audits will be briefly described. An assessment of the possible impact of this type of audit and certification on the practice of preserving digital information will also be provided.

  5. Potential benefits of waste transmutation to the U.S. high-level waste respository

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Michaels, G.E.

    1995-10-01

    This paper reexamines the potential benefits of waste transmutation to the proposed U.S. geologic repository at the Yucca Mountain site based on recent progress in the performance assessment for the Yucca Mountain base case of spent fuel emplacement. It is observed that actinides are assumed to have higher solubility than in previous studies and that Np and other actinides now dominate the projected aqueous releases from a Yucca Mountain repository. Actinides are also indentified as the dominant source of decay heat in the repository, and the effect of decay heat in perturbing the hydrology, geochemistry, and thermal characteristics of Yuccamore » Mountain are reviewed. It is concluded that the potential for thermally-driven, buoyant, gas-phase flow at Yucca Mountain introduces data and modeling requirements that will increase the costs of licensing the site and may cause the site to be unattractive for geologic disposal of wastes. A transmutation-enabled cold repository is proposed that might allow licensing of a repository to be based upon currently observable characteristics of the Yucca Mountain site.« less

  6. A machine learning-based framework to identify type 2 diabetes through electronic health records

    PubMed Central

    Zheng, Tao; Xie, Wei; Xu, Liling; He, Xiaoying; Zhang, Ya; You, Mingrong; Yang, Gong; Chen, You

    2016-01-01

    Objective To discover diverse genotype-phenotype associations affiliated with Type 2 Diabetes Mellitus (T2DM) via genome-wide association study (GWAS) and phenome-wide association study (PheWAS), more cases (T2DM subjects) and controls (subjects without T2DM) are required to be identified (e.g., via Electronic Health Records (EHR)). However, existing expert based identification algorithms often suffer in a low recall rate and could miss a large number of valuable samples under conservative filtering standards. The goal of this work is to develop a semi-automated framework based on machine learning as a pilot study to liberalize filtering criteria to improve recall rate with a keeping of low false positive rate. Materials and methods We propose a data informed framework for identifying subjects with and without T2DM from EHR via feature engineering and machine learning. We evaluate and contrast the identification performance of widely-used machine learning models within our framework, including k-Nearest-Neighbors, Naïve Bayes, Decision Tree, Random Forest, Support Vector Machine and Logistic Regression. Our framework was conducted on 300 patient samples (161 cases, 60 controls and 79 unconfirmed subjects), randomly selected from 23,281 diabetes related cohort retrieved from a regional distributed EHR repository ranging from 2012 to 2014. Results We apply top-performing machine learning algorithms on the engineered features. We benchmark and contrast the accuracy, precision, AUC, sensitivity and specificity of classification models against the state-of-the-art expert algorithm for identification of T2DM subjects. Our results indicate that the framework achieved high identification performances (∼0.98 in average AUC), which are much higher than the state-of-the-art algorithm (0.71 in AUC). Discussion Expert algorithm-based identification of T2DM subjects from EHR is often hampered by the high missing rates due to their conservative selection criteria. Our framework leverages machine learning and feature engineering to loosen such selection criteria to achieve a high identification rate of cases and controls. Conclusions Our proposed framework demonstrates a more accurate and efficient approach for identifying subjects with and without T2DM from EHR. PMID:27919371

  7. A machine learning-based framework to identify type 2 diabetes through electronic health records.

    PubMed

    Zheng, Tao; Xie, Wei; Xu, Liling; He, Xiaoying; Zhang, Ya; You, Mingrong; Yang, Gong; Chen, You

    2017-01-01

    To discover diverse genotype-phenotype associations affiliated with Type 2 Diabetes Mellitus (T2DM) via genome-wide association study (GWAS) and phenome-wide association study (PheWAS), more cases (T2DM subjects) and controls (subjects without T2DM) are required to be identified (e.g., via Electronic Health Records (EHR)). However, existing expert based identification algorithms often suffer in a low recall rate and could miss a large number of valuable samples under conservative filtering standards. The goal of this work is to develop a semi-automated framework based on machine learning as a pilot study to liberalize filtering criteria to improve recall rate with a keeping of low false positive rate. We propose a data informed framework for identifying subjects with and without T2DM from EHR via feature engineering and machine learning. We evaluate and contrast the identification performance of widely-used machine learning models within our framework, including k-Nearest-Neighbors, Naïve Bayes, Decision Tree, Random Forest, Support Vector Machine and Logistic Regression. Our framework was conducted on 300 patient samples (161 cases, 60 controls and 79 unconfirmed subjects), randomly selected from 23,281 diabetes related cohort retrieved from a regional distributed EHR repository ranging from 2012 to 2014. We apply top-performing machine learning algorithms on the engineered features. We benchmark and contrast the accuracy, precision, AUC, sensitivity and specificity of classification models against the state-of-the-art expert algorithm for identification of T2DM subjects. Our results indicate that the framework achieved high identification performances (∼0.98 in average AUC), which are much higher than the state-of-the-art algorithm (0.71 in AUC). Expert algorithm-based identification of T2DM subjects from EHR is often hampered by the high missing rates due to their conservative selection criteria. Our framework leverages machine learning and feature engineering to loosen such selection criteria to achieve a high identification rate of cases and controls. Our proposed framework demonstrates a more accurate and efficient approach for identifying subjects with and without T2DM from EHR. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  8. 10 CFR 60.137 - General requirements for performance confirmation.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... IN GEOLOGIC REPOSITORIES Technical Criteria Performance Confirmation Requirements § 60.137 General requirements for performance confirmation. The geologic repository operations area shall be designed so as to...

  9. Workshop on development of radionuclide getters for the Yucca Mountain waste repository: proceedings.

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Moore, Robert Charles; Lukens, Wayne W.

    The proposed Yucca Mountain repository, located in southern Nevada, is to be the first facility for permanent disposal of spent reactor fuel and high-level radioactive waste in the United States. Total Systems Performance Assessment (TSPA) analysis has indicated that among the major radionuclides contributing to dose are technetium, iodine, and neptunium, all of which are highly mobile in the environment. Containment of these radionuclides within the repository is a priority for the Yucca Mountain Project (YMP). These proceedings review current research and technology efforts for sequestration of the radionuclides with a focus on technetium, iodine, and neptunium. This workshop alsomore » covered issues concerning the Yucca Mountain environment and getter characteristics required for potential placement into the repository.« less

  10. Standards-based metadata procedures for retrieving data for display or mining utilizing persistent (data-DOI) identifiers.

    PubMed

    Harvey, Matthew J; Mason, Nicholas J; McLean, Andrew; Rzepa, Henry S

    2015-01-01

    We describe three different procedures based on metadata standards for enabling automated retrieval of scientific data from digital repositories utilising the persistent identifier of the dataset with optional specification of the attributes of the data document such as filename or media type. The procedures are demonstrated using the JSmol molecular visualizer as a component of a web page and Avogadro as a stand-alone modelling program. We compare our methods for automated retrieval of data from a standards-compliant data repository with those currently in operation for a selection of existing molecular databases and repositories. Our methods illustrate the importance of adopting a standards-based approach of using metadata declarations to increase access to and discoverability of repository-based data. Graphical abstract.

  11. Netlib services and resources

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Browne, S.V.; Green, S.C.; Moore, K.

    1994-04-01

    The Netlib repository, maintained by the University of Tennessee and Oak Ridge National Laboratory, contains freely available software, documents, and databases of interest to the numerical, scientific computing, and other communities. This report includes both the Netlib User`s Guide and the Netlib System Manager`s Guide, and contains information about Netlib`s databases, interfaces, and system implementation. The Netlib repository`s databases include the Performance Database, the Conferences Database, and the NA-NET mail forwarding and Whitepages Databases. A variety of user interfaces enable users to access the Netlib repository in the manner most convenient and compatible with their networking capabilities. These interfaces includemore » the Netlib email interface, the Xnetlib X Windows client, the netlibget command-line TCP/IP client, anonymous FTP, anonymous RCP, and gopher.« less

  12. Analysis of model output and science data in the Virtual Model Repository (VMR).

    NASA Astrophysics Data System (ADS)

    De Zeeuw, D.; Ridley, A. J.

    2014-12-01

    Big scientific data not only includes large repositories of data from scientific platforms like satelites and ground observation, but also the vast output of numerical models. The Virtual Model Repository (VMR) provides scientific analysis and visualization tools for a many numerical models of the Earth-Sun system. Individual runs can be analyzed in the VMR and compared to relevant data through relevant metadata, but larger collections of runs can also now be studied and statistics generated on the accuracy and tendancies of model output. The vast model repository at the CCMC with over 1000 simulations of the Earth's magnetosphere was used to look at overall trends in accuracy when compared to satelites such as GOES, Geotail, and Cluster. Methodology for this analysis as well as case studies will be presented.

  13. 2012 best practices for repositories collection, storage, retrieval, and distribution of biological materials for research international society for biological and environmental repositories.

    PubMed

    2012-04-01

    Third Edition [Formula: see text] [Box: see text] Printed with permission from the International Society for Biological and Environmental Repositories (ISBER) © 2011 ISBER All Rights Reserved Editor-in-Chief Lori D. Campbell, PhD Associate Editors Fay Betsou, PhD Debra Leiolani Garcia, MPA Judith G. Giri, PhD Karen E. Pitt, PhD Rebecca S. Pugh, MS Katherine C. Sexton, MBA Amy P.N. Skubitz, PhD Stella B. Somiari, PhD Individual Contributors to the Third Edition Jonas Astrin, Susan Baker, Thomas J. Barr, Erica Benson, Mark Cada, Lori Campbell, Antonio Hugo Jose Froes Marques Campos, David Carpentieri, Omoshile Clement, Domenico Coppola, Yvonne De Souza, Paul Fearn, Kelly Feil, Debra Garcia, Judith Giri, William E. Grizzle, Kathleen Groover, Keith Harding, Edward Kaercher, Joseph Kessler, Sarah Loud, Hannah Maynor, Kevin McCluskey, Kevin Meagher, Cheryl Michels, Lisa Miranda, Judy Muller-Cohn, Rolf Muller, James O'Sullivan, Karen Pitt, Rebecca Pugh, Rivka Ravid, Katherine Sexton, Ricardo Luis A. Silva, Frank Simione, Amy Skubitz, Stella Somiari, Frans van der Horst, Gavin Welch, Andy Zaayenga 2012 Best Practices for Repositories: Collection, Storage, Retrieval and Distribution of Biological Materials for Research INTERNATIONAL SOCIETY FOR BIOLOGICAL AND ENVIRONMENTAL REPOSITORIES (ISBER) INTRODUCTION T he availability of high quality biological and environmental specimens for research purposes requires the development of standardized methods for collection, long-term storage, retrieval and distribution of specimens that will enable their future use. Sharing successful strategies for accomplishing this goal is one of the driving forces for the International Society for Biological and Environmental Repositories (ISBER). For more information about ISBER see www.isber.org . ISBER's Best Practices for Repositories (Best Practices) reflect the collective experience of its members and has received broad input from other repository professionals. Throughout this document effective practices are presented for the management of specimen collections and repositories. The term "Best Practice" is used in cases where a level of operation is indicated that is above the basic recommended practice or more specifically designates the most effective practice. It is understood that repositories in certain locations or with particular financial constraints may not be able to adhere to each of the items designated as "Best Practices". Repositories fitting into either of these categories will need to decide how they might best adhere to these recommendations within their particular circumstances. While adherence to ISBER Best Practices is strictly on a voluntary basis, it is important to note that some aspects of specimen management are governed by national/federal, regional and local regulations. The reader should refer directly to regulations for their national/federal, regional and local requirements, as appropriate. ISBER has strived to include terminology appropriate to the various specimen types covered under these practices, but here too, the reader should take steps to ensure the appropriateness of the recommendations to their particular repository type prior to the implementation of any new approaches. Important terms within the document are italicized when first used in a section and defined in the glossary. The ISBER Best Practices are periodically reviewed and revised to reflect advances in research and technology. The third edition of the Best Practices builds on the foundation established in the first and second editions which were published in 2005 and 2008, respectively.

  14. Generic Argillite/Shale Disposal Reference Case

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Zheng, Liange; Colon, Carlos Jové; Bianchi, Marco

    Radioactive waste disposal in a deep subsurface repository hosted in clay/shale/argillite is a subject of widespread interest given the desirable isolation properties, geochemically reduced conditions, and widespread geologic occurrence of this rock type (Hansen 2010; Bianchi et al. 2013). Bianchi et al. (2013) provides a description of diffusion in a clay-hosted repository based on single-phase flow and full saturation using parametric data from documented studies in Europe (e.g., ANDRA 2005). The predominance of diffusive transport and sorption phenomena in this clay media are key attributes to impede radionuclide mobility making clay rock formations target sites for disposal of high-level radioactivemore » waste. The reports by Hansen et al. (2010) and those from numerous studies in clay-hosted underground research laboratories (URLs) in Belgium, France and Switzerland outline the extensive scientific knowledge obtained to assess long-term clay/shale/argillite repository isolation performance of nuclear waste. In the past several years under the UFDC, various kinds of models have been developed for argillite repository to demonstrate the model capability, understand the spatial and temporal alteration of the repository, and evaluate different scenarios. These models include the coupled Thermal-Hydrological-Mechanical (THM) and Thermal-Hydrological-Mechanical-Chemical (THMC) models (e.g. Liu et al. 2013; Rutqvist et al. 2014a, Zheng et al. 2014a) that focus on THMC processes in the Engineered Barrier System (EBS) bentonite and argillite host hock, the large scale hydrogeologic model (Bianchi et al. 2014) that investigates the hydraulic connection between an emplacement drift and surrounding hydrogeological units, and Disposal Systems Evaluation Framework (DSEF) models (Greenberg et al. 2013) that evaluate thermal evolution in the host rock approximated as a thermal conduction process to facilitate the analysis of design options. However, the assumptions and the properties (parameters) used in these models are different, which not only make inter-model comparisons difficult, but also compromise the applicability of the lessons learned from one model to another model. The establishment of a reference case would therefore be helpful to set up a baseline for model development. A generic salt repository reference case was developed in Freeze et al. (2013) and the generic argillite repository reference case is presented in this report. The definition of a reference case requires the characterization of the waste inventory, waste form, waste package, repository layout, EBS backfill, host rock, and biosphere. This report mainly documents the processes in EBS bentonite and host rock that are potentially important for performance assessment and properties that are needed to describe these processes, with brief description other components such as waste inventory, waste form, waste package, repository layout, aquifer, and biosphere. A thorough description of the generic argillite repository reference case will be given in Jové Colon et al. (2014).« less

  15. 10 CFR 960.5 - Preclosure guidelines.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REPOSITORY Preclosure Guidelines § 960.5 Preclosure guidelines. The guidelines in this subpart specify the factors to be considered in evaluating and comparing sites on the basis of expected repository performance...

  16. 10 CFR 960.4-2 - Technical guidelines.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REPOSITORY Postclosure Guidelines § 960.4-2 Technical guidelines. The technical guidelines in this subpart... conditions on the characteristics, processes, and events that may influence the performance of a repository...

  17. A maize database resource that captures tissue-specific and subcellular-localized gene expression, via fluorescent tags and confocal imaging (Maize Cell Genomics Database).

    PubMed

    Krishnakumar, Vivek; Choi, Yongwook; Beck, Erin; Wu, Qingyu; Luo, Anding; Sylvester, Anne; Jackson, David; Chan, Agnes P

    2015-01-01

    Maize is a global crop and a powerful system among grain crops for genetic and genomic studies. However, the development of novel biological tools and resources to aid in the functional identification of gene sequences is greatly needed. Towards this goal, we have developed a collection of maize marker lines for studying native gene expression in specific cell types and subcellular compartments using fluorescent proteins (FPs). To catalog FP expression, we have developed a public repository, the Maize Cell Genomics (MCG) Database, (http://maize.jcvi.org/cellgenomics), to organize a large data set of confocal images generated from the maize marker lines. To date, the collection represents major subcellular structures and also developmentally important progenitor cell populations. The resource is available to the research community, for example to study protein localization or interactions under various experimental conditions or mutant backgrounds. A subset of the marker lines can also be used to induce misexpression of target genes through a transactivation system. For future directions, the image repository can be expanded to accept new image submissions from the research community, and to perform customized large-scale computational image analysis. This community resource will provide a suite of new tools for gaining biological insights by following the dynamics of protein expression at the subcellular, cellular and tissue levels. © The Author 2014. Published by Oxford University Press on behalf of Japanese Society of Plant Physiologists. All rights reserved. For permissions, please email: journals.permissions@oup.com.

  18. Mechanical response and microprocesses of reconsolidating crushed salt at elevated temperature

    DOE PAGES

    Broome, S. T.; Bauer, S. J.; Hansen, F. D.; ...

    2015-09-14

    Design, analysis and performance assessment of potential salt repositories for heat-generating nuclear waste require knowledge of thermal, mechanical, and fluid transport properties of reconsolidating granular salt. So, to inform salt repository evaluations, we have undertaken an experimental program to determine Bulk and Young’s moduli and Poisson’s ratio of reconsolidated granular salt as a function of porosity and temperature and to establish the deformational processes by which the salt reconsolidates. Our tests were conducted at 100, 175, and 250 °C. In hydrostatic tests, confining pressure is increased to 20 MPa with periodic unload/reload loops to determine K. Volume strain increases withmore » increasing temperature. In shear tests at 2.5 and 5 MPa confining pressure, after confining pressure is applied, the crushed salt is subjected to a differential stress, with periodic unload/reload loops to determine E and ν. At predetermined differential stress levels the stress is held constant and the salt consolidates. Displacement gages mounted on the samples show little lateral deformation until the samples reach a porosity of ~10 %. Interestingly, vapor is vented only for 250 °C tests and condenses at the vent port. It is hypothesized that the brine originates from fluid inclusions, which were made accessible by heating and intragranular deformational processes including decrepitation. Furthermore, identification and documentation of consolidation processes are inferred from optical and scanning electron microstructural observations. As a result, densification at low porosity is enhanced by water film on grain boundaries that enables solution-precipitation phenomena.« less

  19. Six methodological steps to build medical data warehouses for research.

    PubMed

    Szirbik, N B; Pelletier, C; Chaussalet, T

    2006-09-01

    We propose a simple methodology for heterogeneous data collection and central repository-style database design in healthcare. Our method can be used with or without other software development frameworks, and we argue that its application can save a relevant amount of implementation effort. Also, we believe that the method can be used in other fields of research, especially those that have a strong interdisciplinary nature. The idea emerged during a healthcare research project, which consisted among others in grouping information from heterogeneous and distributed information sources. We developed this methodology by the lessons learned when we had to build a data repository, containing information about elderly patients flows in the UK's long-term care system (LTC). We explain thoroughly those aspects that influenced the methodology building. The methodology is defined by six steps, which can be aligned with various iterative development frameworks. We describe here the alignment of our methodology with the RUP (rational unified process) framework. The methodology emphasizes current trends, as early identification of critical requirements, data modelling, close and timely interaction with users and stakeholders, ontology building, quality management, and exception handling. Of a special interest is the ontological engineering aspect, which had the effects with the highest impact after the project. That is, it helped stakeholders to perform better collaborative negotiations that brought better solutions for the overall system investigated. An insight into the problems faced by others helps to lead the negotiators to win-win situations. We consider that this should be the social result of any project that collects data for better decision making that leads finally to enhanced global outcomes.

  20. Transuranic inventory reduction in repository by partitioning and transmutation

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Kang, C.H.; Kazimi, M.S.

    1992-01-01

    The promise of a new reprocessing technology and the issuance of Environmental Protection Agency (EPA) and U.S. Nuclear Regulatory Commission regulations concerning a geologic repository rekindle the interest in partitioning and transmutation of transuranic (TRU) elements from discharged reactor fuel as a high level waste management option. This paper investigates the TRU repository inventory reduction capability of the proposed advanced liquid metal reactors (ALMRs) and integral fast reactors (IFRs) as well as the plutonium recycled light water reactors (LWRs).

  1. Establishment of Peripheral Nerve Injury Data Repository to Monitor and Support Population Health Decisions

    DTIC Science & Technology

    2017-07-01

    AWARD NUMBER: W81XWH-16-0-DM167033 TITLE: Establishment of Peripheral Nerve Injury Data Repository to Monitor and Support Population Health...Injury Data Repository to Monitor and Support Population Health Decisions 5a. CONTRACT NUMBER 5b. GRANT NUMBER W81XWH-16-0-DM167033 5c. PROGRAM...patient enrollment. Collected data will be utilized to 1) describe the outcomes of various PNI and 2) suggest outcomes that support population health

  2. 10 CFR 60.18 - Review of site characterization activities. 2

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... IN GEOLOGIC REPOSITORIES Licenses Preapplication Review § 60.18 Review of site characterization... its progress in developing the design of a geologic repository operations area appropriate for the...

  3. Investigating the Thermal Limit of Clay Minerals for Applications in Nuclear Waste Repository Design

    NASA Astrophysics Data System (ADS)

    Matteo, E. N.; Miller, A. W.; Kruichak, J.; Mills, M.; Tellez, H.; Wang, Y.

    2013-12-01

    Clay minerals are likely candidates to aid in nuclear waste isolation due to their low permeability, favorable swelling properties, and high cation sorption capacities. Establishing the thermal limit for clay minerals in a nuclear waste repository is a potentially important component of repository design, as flexibility of the heat load within the repository can have a major impact on the selection of repository design. For example, the thermal limit plays a critical role in the time that waste packages would need to cool before being transferred to the repository. Understanding the chemical and physical changes that occur in clay minerals at various temperatures above the current thermal limit (of 100 °C) can enable decision-makers with information critical to evaluating the potential trade-offs of increasing the thermal limit within the repository. Most critical is gaining understanding of how varying thermal conditions in the repository will impact radionuclide sorption and transport in clay materials either as engineered barriers or as disposal media. A variety of clays (illite, mixed layer illite/smectite, montmorillonite, and palygorskite) were heated for a range of temperatures between 100-500 °C. These samples were characterized by a variety of methods, including nitrogen adsorption, x-ray diffraction, thermogravimetric analysis, barium chloride exchange for cation exchange capacity (CEC), and iodide sorption. The nitrogen porosimetry shows that for all the clays, thermally-induced changes in BET surface area are dominated by collapse/creation of the microporosity, i.e. pore diameters < 17 angstroms. Changes in micro porosity (relative to no heat treatment) are most significant for heat treatments 300 °C and above. Alterations are also seen in the chemical properties (CEC, XRD, iodide sorption) of clays, and like pore size distribution changes, are most significant above 300 °C. Overall, the results imply that changes seen in pores size distribution correlate with cation exchange capacity and cation exchange processes. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's Nation Nuclear Security Administration under contract DE-AC04-94AL85000. SAND Number: 2013-6352A.

  4. ContaMiner and ContaBase: a webserver and database for early identification of unwantedly crystallized protein contaminants

    PubMed Central

    Hungler, Arnaud; Momin, Afaque; Diederichs, Kay; Arold, Stefan, T.

    2016-01-01

    Solving the phase problem in protein X-ray crystallography relies heavily on the identity of the crystallized protein, especially when molecular replacement (MR) methods are used. Yet, it is not uncommon that a contaminant crystallizes instead of the protein of interest. Such contaminants may be proteins from the expression host organism, protein fusion tags or proteins added during the purification steps. Many contaminants co-purify easily, crystallize and give good diffraction data. Identification of contaminant crystals may take time, since the presence of the contaminant is unexpected and its identity unknown. A webserver (ContaMiner) and a contaminant database (ContaBase) have been established, to allow fast MR-based screening of crystallographic data against currently 62 known contaminants. The web-based ContaMiner (available at http://strube.cbrc.kaust.edu.sa/contaminer/) currently produces results in 5 min to 4 h. The program is also available in a github repository and can be installed locally. ContaMiner enables screening of novel crystals at synchrotron beamlines, and it would be valuable as a routine safety check for ‘crystallization and preliminary X-ray analysis’ publications. Thus, in addition to potentially saving X-ray crystallographers much time and effort, ContaMiner might considerably lower the risk of publishing erroneous data. PMID:27980519

  5. 10 CFR 960.5-2-2 - Site ownership and control.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... NUCLEAR WASTE REPOSITORY Preclosure Guidelines Preclosure Radiological Safety § 960.5-2-2 Site ownership... control of access that are required in order that surface and subsurface activities during repository...

  6. 10 CFR 960.4-2-1 - Geohydrology.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REPOSITORY Postclosure Guidelines § 960.4-2-1 Geohydrology. (a) Qualifying condition. The present and... the ability of the geologic repository to isolate the waste during the next 100,000 years. (3) Sites...

  7. 10 CFR 60.7 - License not required for certain preliminary activities.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... WASTES IN GEOLOGIC REPOSITORIES General Provisions § 60.7 License not required for certain preliminary... repository: (a) For purposes of site characterization; or (b) For use, during site characterization or...

  8. 10 CFR 960.3-1-1 - Diversity of geohydrologic settings.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... SITES FOR A NUCLEAR WASTE REPOSITORY Implementation Guidelines § 960.3-1-1 Diversity of geohydrologic... development of repositories may be located. To the extent practicable, sites recommended as candidate sites...

  9. CAED Document Repository

    EPA Pesticide Factsheets

    Compliance Assurance and Enforcement Division Document Repository (CAEDDOCRESP) provides internal and external access of Inspection Records, Enforcement Actions, and National Environmental Protection Act (NEPA) documents to all CAED staff. The respository will also include supporting documents, images, etc.

  10. National Pesticide Standard Repository

    EPA Pesticide Factsheets

    EPA's National Pesticide Standards Repository collects and maintains an inventory of analytical “standards” of registered pesticides in the United States, as well as some that are not currently registered for food and product testing and monitoring.

  11. Terminology development towards harmonizing multiple clinical neuroimaging research repositories.

    PubMed

    Turner, Jessica A; Pasquerello, Danielle; Turner, Matthew D; Keator, David B; Alpert, Kathryn; King, Margaret; Landis, Drew; Calhoun, Vince D; Potkin, Steven G; Tallis, Marcelo; Ambite, Jose Luis; Wang, Lei

    2015-07-01

    Data sharing and mediation across disparate neuroimaging repositories requires extensive effort to ensure that the different domains of data types are referred to by commonly agreed upon terms. Within the SchizConnect project, which enables querying across decentralized databases of neuroimaging, clinical, and cognitive data from various studies of schizophrenia, we developed a model for each data domain, identified common usable terms that could be agreed upon across the repositories, and linked them to standard ontological terms where possible. We had the goal of facilitating both the current user experience in querying and future automated computations and reasoning regarding the data. We found that existing terminologies are incomplete for these purposes, even with the history of neuroimaging data sharing in the field; and we provide a model for efforts focused on querying multiple clinical neuroimaging repositories.

  12. Terminology development towards harmonizing multiple clinical neuroimaging research repositories

    PubMed Central

    Turner, Jessica A.; Pasquerello, Danielle; Turner, Matthew D.; Keator, David B.; Alpert, Kathryn; King, Margaret; Landis, Drew; Calhoun, Vince D.; Potkin, Steven G.; Tallis, Marcelo; Ambite, Jose Luis; Wang, Lei

    2015-01-01

    Data sharing and mediation across disparate neuroimaging repositories requires extensive effort to ensure that the different domains of data types are referred to by commonly agreed upon terms. Within the SchizConnect project, which enables querying across decentralized databases of neuroimaging, clinical, and cognitive data from various studies of schizophrenia, we developed a model for each data domain, identified common usable terms that could be agreed upon across the repositories, and linked them to standard ontological terms where possible. We had the goal of facilitating both the current user experience in querying and future automated computations and reasoning regarding the data. We found that existing terminologies are incomplete for these purposes, even with the history of neuroimaging data sharing in the field; and we provide a model for efforts focused on querying multiple clinical neuroimaging repositories. PMID:26688838

  13. Natural geochemical analogues of the near field of high-level nuclear waste repositories

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Apps, J.A.

    1995-09-01

    United States practice has been to design high-level nuclear waste (HLW) geological repositories with waste densities sufficiently high that repository temperatures surrounding the waste will exceed 100{degrees}C and could reach 250{degrees}C. Basalt and devitrified vitroclastic tuff are among the host rocks considered for waste emplacement. Near-field repository thermal behavior and chemical alteration in such rocks is expected to be similar to that observed in many geothermal systems. Therefore, the predictive modeling required for performance assessment studies of the near field could be validated and calibrated using geothermal systems as natural analogues. Examples are given which demonstrate the need for refinementmore » of the thermodynamic databases used in geochemical modeling of near-field natural analogues and the extent to which present models can predict conditions in geothermal fields.« less

  14. Testimony of Dr. Raul A. Deju, Basalt Waste Isolation Project, before the Subcommittee on Energy Research and Production, Committee on Sceince and Technology, United States House of Representatives, March 2, 1983

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Not Available

    1983-01-01

    Status of the Basalt Waste Isolation Project is given. Three key concerns have been identified that need to be resolved to either confirm or eliminate the basalts as a potential nuclear waste repository host medium. They are: A thorough understanding of the groundwater hydrology beneath the Hanford Site is needed to assure that a repository in basalt will not contribute unacceptable amounts of contaminants to the accessible environment. Our ability to construct a repository shaft and a network of underground tunnels needs to be fully demonstrated through an exploratory shaft program. Our ability to ultimately seal a repository, such thatmore » its integrity and the isolation of the waste are guaranteed, needs to be demonstrated.« less

  15. Evaluation of Five Sedimentary Rocks Other Than Salt for Geologic Repository Siting Purposes

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Croff, A.G.; Lomenick, T.F.; Lowrie, R.S.

    The US Department of Energy (DOE), in order to increase the diversity of rock types under consideration by the geologic disposal program, initiated the Sedimary ROck Program (SERP), whose immediate objectiv eis to evaluate five types of secimdnary rock - sandstone, chalk, carbonate rocks (limestone and dolostone), anhydrock, and shale - to determine the potential for siting a geologic repository. The evaluation of these five rock types, together with the ongoing salt studies, effectively results in the consideration of all types of relatively impermeable sedimentary rock for repository purposes. The results of this evaluation are expressed in terms of amore » ranking of the five rock types with respect to their potential to serve as a geologic repository host rock. This comparative evaluation was conducted on a non-site-specific basis, by use of generic information together with rock evaluation criteria (RECs) derived from the DOE siting guidelines for geologic repositories (CFR 1984). An information base relevant to rock evaluation using these RECs was developed in hydrology, geochemistry, rock characteristics (rock occurrences, thermal response, rock mechanics), natural resources, and rock dissolution. Evaluation against postclosure and preclosure RECs yielded a ranking of the five subject rocks with respect to their potential as repository host rocks. Shale was determined to be the most preferred of the five rock types, with sandstone a distant second, the carbonate rocks and anhydrock a more distant third, and chalk a relatively close fourth.« less

  16. The Rail Alignment Environmental Impact Statement: An Update

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    R. Sweeney

    2005-01-20

    On July 23,2002, the President of the United States signed into law a joint resolution of the United States Congress designating the Yucca Mountain site in Nye County, Nevada, for development as a geologic repository for the disposal of spent nuclear fuel and high-level radioactive waste. If the US. Nuclear Regulatory Commission authorizes construction of the repository and receipt and possession of spent nuclear fuel and high-level radioactive at Yucca Mountain, the U.S. Department of Energy (DOE) would be responsible for transporting these materials to the Yucca Mountain repository as part of its obligation under the Nuclear Waste Policy Act.more » Part of the site recommendation decision included the analysis of a nation-wide shipping campaign to the proposed repository site. The ''Final Environmental Impact Statement for a Geologic Repository for the Disposal of Spent Nuclear Fuel and High-Level Radioactive Waste at Yucca Mountain, Nye County, Nevada'' (February 2002) (Repository EIS) evaluated the potential impacts of the transportation of 70,000 Metric Tons of Heavy Metal spent nuclear fuel and high-level radioactive waste from 77 locations around the nation to the potential repository in Nevada over a 24 year shipping campaign. In the Repository EIS, DOE identified mostly rail as its preferred mode of transportation, both nationally and in the State of Nevada. In December 2003, based on public comments and the environmental analyses in the Repository EIS, DOE identified a preference for the Caliente rail corridor in Nevada. On April 8, 2004, DOE issued a Record of Decision (ROD) on the Mode of Transportation and Nevada Rail Corridor for the Disposal of Spent Nuclear Fuel and High-Level Radioactive Waste at Yucca Mountain, Nye County, Nevada. In this ROD, the DOE announced that it had decided to select the mostly rail scenario analyzed in the Repository EIS as the transportation mode both on a national basis and in the State of Nevada. Under the mostly rail scenario, the DOE would rely on a combination of rail, truck and possibly barge to transport to the repository site at Yucca Mountain up to 70,000 MTHM of spent nuclear fuel and high-level radioactive waste, with most of the spent nuclear fuel and high-level radioactive waste being transported by rail. This will ultimately require construction of a rail line in Nevada to the repository. In addition, the DOE has decided to select the Caliente rail corridor in which to examine potential alignments within which to construct that rail line. A corridor is a strip of land, approximately 400 meters (0.25 miles) wide, that encompasses one of several possible routes through which DOE could build a rail line. An alignment is the specific location of a rail line in a corridor, and would likely be 60 meters [200 feet] or less in width. Also on April 8, 2004, DOE issued a Notice of Intent to Prepare an Environmental Impact Statement for the Alignment, Construction, and Operation of a Rail Line to a Geologic Repository at Yucca Mountain, Nye County, NV. In the Notice of Intent, the Department announced its intent to prepare a Rail Alignment EIS to assist in selecting a possible alignment for construction of a rail line that would connect the repository at Yucca Mountain to an existing main rail line in Nevada. The Rail Alignment EIS also would consider the potential construction and operation of a rail-to-truck intermodal transfer facility, proposed to be located at the confluence of an existing mainline railroad and a highway, to support legal-weight truck transportation until the rail system is fully operational. This corridor is approximately 513 kilometers (319 miles) long and would cost an estimated $880 million (2001 dollars). Should DOE decide to build the Caliente corridor, it may be the longest rail line built in the United States since the Transcontinental Railroad was constructed in 1869. Some of the challenges in building this rail corridor are steep grades (the corridor crosses over 7 mountain ranges), isolated terrain, possible tunnels, and stakeholder acceptance.« less

  17. Development of a pseudo/anonymised primary care research database: Proof-of-concept study.

    PubMed

    MacRury, Sandra; Finlayson, Jim; Hussey-Wilson, Susan; Holden, Samantha

    2016-06-01

    General practice records present a comprehensive source of data that could form a variety of anonymised or pseudonymised research databases to aid identification of potential research participants regardless of location. A proof-of-concept study was undertaken to extract data from general practice systems in 15 practices across the region to form pseudo and anonymised research data sets. Two feasibility studies and a disease surveillance study compared numbers of potential study participants and accuracy of disease prevalence, respectively. There was a marked reduction in screening time and increase in numbers of potential study participants identified with the research repository compared with conventional methods. Accurate disease prevalence was established and enhanced with the addition of selective text mining. This study confirms the potential for development of national anonymised research database from general practice records in addition to improving data collection for local or national audits and epidemiological projects. © The Author(s) 2014.

  18. Role of genomics in promoting the utilization of plant genetic resources in genebanks

    PubMed Central

    Wambugu, Peterson W; Ndjiondjop, Marie-Noelle

    2018-01-01

    Abstract Global efforts have seen the world’s plant genetic resources (PGRs) conserved in about 1625 germ plasm repositories. Utility of these resources is important in increasing the resilience and productivity of agricultural production systems. However, despite their importance, utility of these resources has been poor. This article reviews the real and potential application of the current advances in genomic technologies in improving the utilization of these resources. The actual and potential application of these genomic approaches in plant identification, phylogenetic analysis, analysing the genetic value of germ plasm, facilitating germ plasm selection in genebanks as well as instilling confidence in international germ plasm exchange system is discussed. We note that if genebanks are to benefit from this genomic revolution, there is need for fundamental changes in the way genebanks are managed, perceived, organized and funded. Increased collaboration between genebank managers and the user community is also recommended PMID:29688255

  19. ProBiS-database: precalculated binding site similarities and local pairwise alignments of PDB structures.

    PubMed

    Konc, Janez; Cesnik, Tomo; Konc, Joanna Trykowska; Penca, Matej; Janežič, Dušanka

    2012-02-27

    ProBiS-Database is a searchable repository of precalculated local structural alignments in proteins detected by the ProBiS algorithm in the Protein Data Bank. Identification of functionally important binding regions of the protein is facilitated by structural similarity scores mapped to the query protein structure. PDB structures that have been aligned with a query protein may be rapidly retrieved from the ProBiS-Database, which is thus able to generate hypotheses concerning the roles of uncharacterized proteins. Presented with uncharacterized protein structure, ProBiS-Database can discern relationships between such a query protein and other better known proteins in the PDB. Fast access and a user-friendly graphical interface promote easy exploration of this database of over 420 million local structural alignments. The ProBiS-Database is updated weekly and is freely available online at http://probis.cmm.ki.si/database.

  20. FlyRNAi.org—the database of the Drosophila RNAi screening center and transgenic RNAi project: 2017 update

    PubMed Central

    Hu, Yanhui; Comjean, Aram; Roesel, Charles; Vinayagam, Arunachalam; Flockhart, Ian; Zirin, Jonathan; Perkins, Lizabeth; Perrimon, Norbert; Mohr, Stephanie E.

    2017-01-01

    The FlyRNAi database of the Drosophila RNAi Screening Center (DRSC) and Transgenic RNAi Project (TRiP) at Harvard Medical School and associated DRSC/TRiP Functional Genomics Resources website (http://fgr.hms.harvard.edu) serve as a reagent production tracking system, screen data repository, and portal to the community. Through this portal, we make available protocols, online tools, and other resources useful to researchers at all stages of high-throughput functional genomics screening, from assay design and reagent identification to data analysis and interpretation. In this update, we describe recent changes and additions to our website, database and suite of online tools. Recent changes reflect a shift in our focus from a single technology (RNAi) and model species (Drosophila) to the application of additional technologies (e.g. CRISPR) and support of integrated, cross-species approaches to uncovering gene function using functional genomics and other approaches. PMID:27924039

  1. Complementary approaches to diagnosing marine diseases: a union of the modern and the classic

    PubMed Central

    Burge, Colleen A.; Friedman, Carolyn S.; Getchell, Rodman; House, Marcia; Mydlarz, Laura D.; Prager, Katherine C.; Renault, Tristan; Kiryu, Ikunari; Vega-Thurber, Rebecca

    2016-01-01

    Linking marine epizootics to a specific aetiology is notoriously difficult. Recent diagnostic successes show that marine disease diagnosis requires both modern, cutting-edge technology (e.g. metagenomics, quantitative real-time PCR) and more classic methods (e.g. transect surveys, histopathology and cell culture). Here, we discuss how this combination of traditional and modern approaches is necessary for rapid and accurate identification of marine diseases, and emphasize how sole reliance on any one technology or technique may lead disease investigations astray. We present diagnostic approaches at different scales, from the macro (environment, community, population and organismal scales) to the micro (tissue, organ, cell and genomic scales). We use disease case studies from a broad range of taxa to illustrate diagnostic successes from combining traditional and modern diagnostic methods. Finally, we recognize the need for increased capacity of centralized databases, networks, data repositories and contingency plans for diagnosis and management of marine disease. PMID:26880839

  2. Complementary approaches to diagnosing marine diseases: a union of the modern and the classic

    USGS Publications Warehouse

    Burge, Colleen A.; Friedman, Carolyn S.; Getchell, Rodman G.; House, Marcia; Lafferty, Kevin D.; Mydlarz, Laura D.; Prager, Katherine C.; Sutherland, Kathryn P.; Renault, Tristan; Kiryu, Ikunari; Vega-Thurber, Rebecca

    2016-01-01

    Linking marine epizootics to a specific aetiology is notoriously difficult. Recent diagnostic successes show that marine disease diagnosis requires both modern, cutting-edge technology (e.g. metagenomics, quantitative real-time PCR) and more classic methods (e.g. transect surveys, histopathology and cell culture). Here, we discuss how this combination of traditional and modern approaches is necessary for rapid and accurate identification of marine diseases, and emphasize how sole reliance on any one technology or technique may lead disease investigations astray. We present diagnostic approaches at different scales, from the macro (environment, community, population and organismal scales) to the micro (tissue, organ, cell and genomic scales). We use disease case studies from a broad range of taxa to illustrate diagnostic successes from combining traditional and modern diagnostic methods. Finally, we recognize the need for increased capacity of centralized databases, networks, data repositories and contingency plans for diagnosis and management of marine disease.

  3. Digital data for quick response (QR) codes of alkalophilic Bacillus pumilus to identify and to compare bacilli isolated from Lonar Crator Lake, India.

    PubMed

    Rekadwad, Bhagwan N; Khobragade, Chandrahasya N

    2016-06-01

    Microbiologists are routinely engaged isolation, identification and comparison of isolated bacteria for their novelty. 16S rRNA sequences of Bacillus pumilus were retrieved from NCBI repository and generated QR codes for sequences (FASTA format and full Gene Bank information). 16SrRNA were used to generate quick response (QR) codes of Bacillus pumilus isolated from Lonar Crator Lake (19° 58' N; 76° 31' E), India. Bacillus pumilus 16S rRNA gene sequences were used to generate CGR, FCGR and PCA. These can be used for visual comparison and evaluation respectively. The hyperlinked QR codes, CGR, FCGR and PCA of all the isolates are made available to the users on a portal https://sites.google.com/site/bhagwanrekadwad/. This generated digital data helps to evaluate and compare any Bacillus pumilus strain, minimizes laboratory efforts and avoid misinterpretation of the species.

  4. Patient Privacy in the Era of Big Data.

    PubMed

    Kayaalp, Mehmet

    2018-01-20

    Privacy was defined as a fundamental human right in the Universal Declaration of Human Rights at the 1948 United Nations General Assembly. However, there is still no consensus on what constitutes privacy. In this review, we look at the evolution of privacy as a concept from the era of Hippocrates to the era of social media and big data. To appreciate the modern measures of patient privacy protection and correctly interpret the current regulatory framework in the United States, we need to analyze and understand the concepts of individually identifiable information, individually identifiable health information, protected health information, and de-identification. The Privacy Rule of the Health Insurance Portability and Accountability Act defines the regulatory framework and casts a balance between protective measures and access to health information for secondary (scientific) use. The rule defines the conditions when health information is protected by law and how protected health information can be de-identified for secondary use. With the advents of artificial intelligence and computational linguistics, computational text de-identification algorithms produce de-identified results nearly as well as those produced by human experts, but much faster, more consistently and basically for free. Modern clinical text de-identification systems now pave the road to big data and enable scientists to access de-identified clinical information while firmly protecting patient privacy. However, clinical text de-identification is not a perfect process. In order to maximize the protection of patient privacy and to free clinical and scientific information from the confines of electronic healthcare systems, all stakeholders, including patients, health institutions and institutional review boards, scientists and the scientific communities, as well as regulatory and law enforcement agencies must collaborate closely. On the one hand, public health laws and privacy regulations define rules and responsibilities such as requesting and granting only the amount of health information that is necessary for the scientific study. On the other hand, developers of de-identification systems provide guidelines to use different modes of operations to maximize the effectiveness of their tools and the success of de-identification. Institutions with clinical repositories need to follow these rules and guidelines closely to successfully protect patient privacy. To open the gates of big data to scientific communities, healthcare institutions need to be supported in their de-identification and data sharing efforts by the public, scientific communities, and local, state, and federal legislators and government agencies.

  5. Patient Privacy in the Era of Big Data

    PubMed Central

    Kayaalp, Mehmet

    2018-01-01

    Privacy was defined as a fundamental human right in the Universal Declaration of Human Rights at the 1948 United Nations General Assembly. However, there is still no consensus on what constitutes privacy. In this review, we look at the evolution of privacy as a concept from the era of Hippocrates to the era of social media and big data. To appreciate the modern measures of patient privacy protection and correctly interpret the current regulatory framework in the United States, we need to analyze and understand the concepts of individually identifiable information, individually identifiable health information, protected health information, and de-identification. The Privacy Rule of the Health Insurance Portability and Accountability Act defines the regulatory framework and casts a balance between protective measures and access to health information for secondary (scientific) use. The rule defines the conditions when health information is protected by law and how protected health information can be de-identified for secondary use. With the advents of artificial intelligence and computational linguistics, computational text de-identification algorithms produce de-identified results nearly as well as those produced by human experts, but much faster, more consistently and basically for free. Modern clinical text de-identification systems now pave the road to big data and enable scientists to access de-identified clinical information while firmly protecting patient privacy. However, clinical text de-identification is not a perfect process. In order to maximize the protection of patient privacy and to free clinical and scientific information from the confines of electronic healthcare systems, all stakeholders, including patients, health institutions and institutional review boards, scientists and the scientific communities, as well as regulatory and law enforcement agencies must collaborate closely. On the one hand, public health laws and privacy regulations define rules and responsibilities such as requesting and granting only the amount of health information that is necessary for the scientific study. On the other hand, developers of de-identification systems provide guidelines to use different modes of operations to maximize the effectiveness of their tools and the success of de-identification. Institutions with clinical repositories need to follow these rules and guidelines closely to successfully protect patient privacy. To open the gates of big data to scientific communities, healthcare institutions need to be supported in their de-identification and data sharing efforts by the public, scientific communities, and local, state, and federal legislators and government agencies. PMID:28903886

  6. Individual identification via electrocardiogram analysis.

    PubMed

    Fratini, Antonio; Sansone, Mario; Bifulco, Paolo; Cesarelli, Mario

    2015-08-14

    During last decade the use of ECG recordings in biometric recognition studies has increased. ECG characteristics made it suitable for subject identification: it is unique, present in all living individuals, and hard to forge. However, in spite of the great number of approaches found in literature, no agreement exists on the most appropriate methodology. This study aimed at providing a survey of the techniques used so far in ECG-based human identification. Specifically, a pattern recognition perspective is here proposed providing a unifying framework to appreciate previous studies and, hopefully, guide future research. We searched for papers on the subject from the earliest available date using relevant electronic databases (Medline, IEEEXplore, Scopus, and Web of Knowledge). The following terms were used in different combinations: electrocardiogram, ECG, human identification, biometric, authentication and individual variability. The electronic sources were last searched on 1st March 2015. In our selection we included published research on peer-reviewed journals, books chapters and conferences proceedings. The search was performed for English language documents. 100 pertinent papers were found. Number of subjects involved in the journal studies ranges from 10 to 502, age from 16 to 86, male and female subjects are generally present. Number of analysed leads varies as well as the recording conditions. Identification performance differs widely as well as verification rate. Many studies refer to publicly available databases (Physionet ECG databases repository) while others rely on proprietary recordings making difficult them to compare. As a measure of overall accuracy we computed a weighted average of the identification rate and equal error rate in authentication scenarios. Identification rate resulted equal to 94.95 % while the equal error rate equal to 0.92 %. Biometric recognition is a mature field of research. Nevertheless, the use of physiological signals features, such as the ECG traits, needs further improvements. ECG features have the potential to be used in daily activities such as access control and patient handling as well as in wearable electronics applications. However, some barriers still limit its growth. Further analysis should be addressed on the use of single lead recordings and the study of features which are not dependent on the recording sites (e.g. fingers, hand palms). Moreover, it is expected that new techniques will be developed using fiducials and non-fiducial based features in order to catch the best of both approaches. ECG recognition in pathological subjects is also worth of additional investigations.

  7. Automatic identification of the reference system based on the fourth ventricular landmarks in T1-weighted MR images.

    PubMed

    Fu, Yili; Gao, Wenpeng; Chen, Xiaoguang; Zhu, Minwei; Shen, Weigao; Wang, Shuguo

    2010-01-01

    The reference system based on the fourth ventricular landmarks (including the fastigial point and ventricular floor plane) is used in medical image analysis of the brain stem. The objective of this study was to develop a rapid, robust, and accurate method for the automatic identification of this reference system on T1-weighted magnetic resonance images. The fully automated method developed in this study consisted of four stages: preprocessing of the data set, expectation-maximization algorithm-based extraction of the fourth ventricle in the region of interest, a coarse-to-fine strategy for identifying the fastigial point, and localization of the base point. The method was evaluated on 27 Brain Web data sets qualitatively and 18 Internet Brain Segmentation Repository data sets and 30 clinical scans quantitatively. The results of qualitative evaluation indicated that the method was robust to rotation, landmark variation, noise, and inhomogeneity. The results of quantitative evaluation indicated that the method was able to identify the reference system with an accuracy of 0.7 +/- 0.2 mm for the fastigial point and 1.1 +/- 0.3 mm for the base point. It took <6 seconds for the method to identify the related landmarks on a personal computer with an Intel Core 2 6300 processor and 2 GB of random-access memory. The proposed method for the automatic identification of the reference system based on the fourth ventricular landmarks was shown to be rapid, robust, and accurate. The method has potentially utility in image registration and computer-aided surgery.

  8. Gene prioritization and clustering by multi-view text mining

    PubMed Central

    2010-01-01

    Background Text mining has become a useful tool for biologists trying to understand the genetics of diseases. In particular, it can help identify the most interesting candidate genes for a disease for further experimental analysis. Many text mining approaches have been introduced, but the effect of disease-gene identification varies in different text mining models. Thus, the idea of incorporating more text mining models may be beneficial to obtain more refined and accurate knowledge. However, how to effectively combine these models still remains a challenging question in machine learning. In particular, it is a non-trivial issue to guarantee that the integrated model performs better than the best individual model. Results We present a multi-view approach to retrieve biomedical knowledge using different controlled vocabularies. These controlled vocabularies are selected on the basis of nine well-known bio-ontologies and are applied to index the vast amounts of gene-based free-text information available in the MEDLINE repository. The text mining result specified by a vocabulary is considered as a view and the obtained multiple views are integrated by multi-source learning algorithms. We investigate the effect of integration in two fundamental computational disease gene identification tasks: gene prioritization and gene clustering. The performance of the proposed approach is systematically evaluated and compared on real benchmark data sets. In both tasks, the multi-view approach demonstrates significantly better performance than other comparing methods. Conclusions In practical research, the relevance of specific vocabulary pertaining to the task is usually unknown. In such case, multi-view text mining is a superior and promising strategy for text-based disease gene identification. PMID:20074336

  9. Albedo Neutron Dosimetry in a Deep Geological Disposal Repository for High-Level Nuclear Waste.

    PubMed

    Pang, Bo; Becker, Frank

    2017-04-28

    Albedo neutron dosemeter is the German official personal neutron dosemeter in mixed radiation fields where neutrons contribute to personal dose. In deep geological repositories for high-level nuclear waste, where neutrons can dominate the radiation field, it is of interest to investigate the performance of albedo neutron dosemeter in such facilities. In this study, the deep geological repository is represented by a shielding cask loaded with spent nuclear fuel placed inside a rock salt emplacement drift. Due to the backscattering of neutrons in the drift, issues concerning calibration of the dosemeter arise. Field-specific calibration of the albedo neutron dosemeter was hence performed with Monte Carlo simulations. In order to assess the applicability of the albedo neutron dosemeter in a deep geological repository over a long time scale, spent nuclear fuel with different ages of 50, 100 and 500 years were investigated. It was found out, that the neutron radiation field in a deep geological repository can be assigned to the application area 'N1' of the albedo neutron dosemeter, which is typical in reactors and accelerators with heavy shielding. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  10. A Digital Broadcast Item (DBI) enabling metadata repository for digital, interactive television (digiTV) feedback channel networks

    NASA Astrophysics Data System (ADS)

    Lugmayr, Artur R.; Mailaparampil, Anurag; Tico, Florina; Kalli, Seppo; Creutzburg, Reiner

    2003-01-01

    Digital television (digiTV) is an additional multimedia environment, where metadata is one key element for the description of arbitrary content. This implies adequate structures for content description, which is provided by XML metadata schemes (e.g. MPEG-7, MPEG-21). Content and metadata management is the task of a multimedia repository, from which digiTV clients - equipped with an Internet connection - can access rich additional multimedia types over an "All-HTTP" protocol layer. Within this research work, we focus on conceptual design issues of a metadata repository for the storage of metadata, accessible from the feedback channel of a local set-top box. Our concept describes the whole heterogeneous life-cycle chain of XML metadata from the service provider to the digiTV equipment, device independent representation of content, accessing and querying the metadata repository, management of metadata related to digiTV, and interconnection of basic system components (http front-end, relational database system, and servlet container). We present our conceptual test configuration of a metadata repository that is aimed at a real-world deployment, done within the scope of the future interaction (fiTV) project at the Digital Media Institute (DMI) Tampere (www.futureinteraction.tv).

  11. The JRC Nanomaterials Repository: A unique facility providing representative test materials for nanoEHS research.

    PubMed

    Totaro, Sara; Cotogno, Giulio; Rasmussen, Kirsten; Pianella, Francesca; Roncaglia, Marco; Olsson, Heidi; Riego Sintes, Juan M; Crutzen, Hugues P

    2016-11-01

    The European Commission has established a Nanomaterials Repository that hosts industrially manufactured nanomaterials that are distributed world-wide for safety testing of nanomaterials. In a first instance these materials were tested in the OECD Testing Programme. They have then also been tested in several EU funded research projects. The JRC Repository of Nanomaterials has thus developed into serving the global scientific community active in the nanoEHS (regulatory) research. The unique Repository facility is a state-of-the-art installation that allows customised sub-sampling under the safest possible conditions, with traceable final sample vials distributed world-wide for research purposes. This paper describes the design of the Repository to perform a semi-automated subsampling procedure, offering high degree of flexibility and precision in the preparation of NM vials for customers, while guaranteeing the safety of the operators, and environmental protection. The JRC nanomaterials are representative for part of the world NMs market. Their wide use world-wide facilitates the generation of comparable and reliable experimental results and datasets in (regulatory) research by the scientific community, ultimately supporting the further development of the OECD regulatory test guidelines. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

  12. Childhood vesicoureteral reflux studies: registries and repositories sources and nosology.

    PubMed

    Chesney, Russell W; Patters, Andrea B

    2013-12-01

    Despite several recent studies, the advisability of antimicrobial prophylaxis and certain imaging studies for urinary tract infections (UTIs) remains controversial. The role of vesicoureteral reflux (VUR) on the severity and re-infection rates for UTIs is also difficult to assess. Registries and repositories of data and biomaterials from clinical studies in children with VUR are valuable. Disease registries are collections of secondary data related to patients with a specific diagnosis, condition or procedure. Registries differ from indices in that they contain more extensive data. A research repository is an entity that receives, stores, processes and/or disseminates specimens (or other materials) as needed. It encompasses the physical location as well as the full range of activities associated with its operation. It may also be referred to as a biorepository. This report provides information about some current registries and repositories that include data and samples from children with VUR. It also describes the heterogeneous nature of the subjects, as some registries and repositories include only data or samples from patients with primary reflux while others also include those from patients with syndromic or secondary reflux. Copyright © 2012 Journal of Pediatric Urology Company. All rights reserved.

  13. National Aeronautics and Space Administration Biological Specimen Repository

    NASA Technical Reports Server (NTRS)

    McMonigal, Kathleen A.; Pietrzyk, Robert a.; Johnson, Mary Anne

    2008-01-01

    The National Aeronautics and Space Administration Biological Specimen Repository (Repository) is a storage bank that is used to maintain biological specimens over extended periods of time and under well-controlled conditions. Samples from the International Space Station (ISS), including blood and urine, will be collected, processed and archived during the preflight, inflight and postflight phases of ISS missions. This investigation has been developed to archive biosamples for use as a resource for future space flight related research. The International Space Station (ISS) provides a platform to investigate the effects of microgravity on human physiology prior to lunar and exploration class missions. The storage of crewmember samples from many different ISS flights in a single repository will be a valuable resource with which researchers can study space flight related changes and investigate physiological markers. The development of the National Aeronautics and Space Administration Biological Specimen Repository will allow for the collection, processing, storage, maintenance, and ethical distribution of biosamples to meet goals of scientific and programmatic relevance to the space program. Archiving of the biosamples will provide future research opportunities including investigating patterns of physiological changes, analysis of components unknown at this time or analyses performed by new methodologies.

  14. User Oriented Platform for Data Analytics in Medical Imaging Repositories.

    PubMed

    Valerio, Miguel; Godinho, Tiago Marques; Costa, Carlos

    2016-01-01

    The production of medical imaging studies and associated data has been growing in the last decades. Their primary use is to support medical diagnosis and treatment processes. However, the secondary use of the tremendous amount of stored data is generally more limited. Nowadays, medical imaging repositories have turned into rich databanks holding not only the images themselves, but also a wide range of metadata related to the medical practice. Exploring these repositories through data analysis and business intelligence techniques has the potential of increasing the efficiency and quality of the medical practice. Nevertheless, the continuous production of tremendous amounts of data makes their analysis difficult by conventional approaches. This article proposes a novel automated methodology to derive knowledge from medical imaging repositories that does not disrupt the regular medical practice. Our method is able to apply statistical analysis and business intelligence techniques directly on top of live institutional repositories. It is a Web-based solution that provides extensive dashboard capabilities, including complete charting and reporting options, combined with data mining components. Moreover, it enables the operator to set a wide multitude of query parameters and operators through the use of an intuitive graphical interface.

  15. Comparison of selected foreign plans and practices for spent fuel and high-level waste management

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Schneider, K.J.; Mitchell, S.J.; Lakey, L.T.

    1990-04-01

    This report describes the major parameters for management of spent nuclear fuel and high-level radioactive wastes in selected foreign countries as of December 1989 and compares them with those in the United States. The foreign countries included in this study are Belgium, Canada, France, the Federal Republic of Germany, Japan, Sweden, Switzerland, and the United Kingdom. All the countries are planning for disposal of spent fuel and/or high-level wastes in deep geologic repositories. Most countries (except Canada and Sweden) plan to reprocess their spent fuel and vitrify the resultant high-level liquid wastes; in comparison, the US plans direct disposal ofmore » spent fuel. The US is planning to use a container for spent fuel as the primary engineered barrier. The US has the most developed repository concept and has one of the earliest scheduled repository startup dates. The repository environment presently being considered in the US is unique, being located in tuff above the water table. The US also has the most prescriptive regulations and performance requirements for the repository system and its components. 135 refs., 8 tabs.« less

  16. Burn Incidence and Treatment in the U.S.

    MedlinePlus

    ... state health data systems, and the National Burn Repository (NBR) of the American Burn Association (ABA). ABA ... Burn Admissions to Burn Centers (ABA National Burn Repository 2015) Survival Rate: 96.8% Gender: 68% Male, ...

  17. 10 CFR 960.4-2-8-1 - Natural resources.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REPOSITORY Postclosure Guidelines § 960.4-2-8-1 Natural resources. (a) Qualifying condition. This site shall... repository-site evaluation to a depth sufficient to affect waste containment and isolation. (4) Evidence of a...

  18. Accelerating research through reagent repositories: the genome editing example.

    PubMed

    Joung, J Keith; Voytas, Daniel F; Kamens, Joanne

    2015-11-20

    Keith Joung, Dan Voytas and Joanne Kamens share insights into how the genome editing field was advanced by early access to biological resources and the role in this process that plasmid repositories play.

  19. 75 FR 33312 - Indexing Structured Product Labeling for Human Prescription Drug and Biological Products; Request...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-11

    ... for use as terms to search repositories of approved prescription medical product structured product... access repository. Considering FDA's available resources, we have instituted a phased implementation of...

  20. Ontology for Transforming Geo-Spatial Data for Discovery and Integration of Scientific Data

    NASA Astrophysics Data System (ADS)

    Nguyen, L.; Chee, T.; Minnis, P.

    2013-12-01

    Discovery and access to geo-spatial scientific data across heterogeneous repositories and multi-discipline datasets can present challenges for scientist. We propose to build a workflow for transforming geo-spatial datasets into semantic environment by using relationships to describe the resource using OWL Web Ontology, RDF, and a proposed geo-spatial vocabulary. We will present methods for transforming traditional scientific dataset, use of a semantic repository, and querying using SPARQL to integrate and access datasets. This unique repository will enable discovery of scientific data by geospatial bound or other criteria.

  1. Data Storing Proposal from Heterogeneous Systems into a Specialized Repository

    NASA Astrophysics Data System (ADS)

    Václavová, Andrea; Tanuška, Pavol; Jánošík, Ján

    2016-12-01

    The aim of this paper is to analyze and to propose an appropriate system for processing and simultaneously storing a vast volume of structured and unstructured data. The paper consists of three parts. The first part addresses the issue of structured and unstructured data. The second part provides the detailed analysis of data repositories and subsequent evaluation indicating which system would be for the given type and volume of data optimal. The third part focuses on the use of gathered information to transfer data to the proposed repository.

  2. DSpace and customized controlled vocabularies

    NASA Astrophysics Data System (ADS)

    Skourlas, C.; Tsolakidis, A.; Kakoulidis, P.; Giannakopoulos, G.

    2015-02-01

    The open source platform of DSpace could be defined as a repository application used to provide access to digital resources. DSpace is installed and used by more than 1000 organizations worldwide. A predefined taxonomy of keyword, called the Controlled Vocabulary, can be used for describing and accessing the information items stored in the repository. In this paper, we describe how the users can create, and customize their own vocabularies. Various heterogeneous items, such as research papers, videos, articles and educational material of the repository, can be indexed in order to provide advanced search functionality using new controlled vocabularies.

  3. Thermoelastic analysis of spent fuel and high level radioactive waste repositories in salt. A semi-analytical solution. [JUDITH

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    St. John, C.M.

    1977-04-01

    An underground repository containing heat generating, High Level Waste or Spent Unreprocessed Fuel may be approximated as a finite number of heat sources distributed across the plane of the repository. The resulting temperature, displacement and stress changes may be calculated using analytical solutions, providing linear thermoelasticity is assumed. This report documents a computer program based on this approach and gives results that form the basis for a comparison between the effects of disposing of High Level Waste and Spent Unreprocessed Fuel.

  4. Optimizing procedures for a human genome repository

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Nierman, W.C.

    1991-03-01

    Large numbers of clones will be generated during the Human Genome Project. As each is characterized, subsets will be identified which are useful to the scientific community at large. These subsets are most readily distributed through public repositories. The American Type Culture Collection (ATCC) is experienced in repository operation, but before this project had no history in managing clones and associated information in large batches instead of individually. This project permitted the ATCC to develop several procedures for automating and thus reducing the cost of characterizing, preserving, and maintaining information about clones.

  5. System-Level Logistics for Dual Purpose Canister Disposal

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Kalinina, Elena A.

    2014-06-03

    The analysis presented in this report investigated how the direct disposal of dual purpose canisters (DPCs) may be affected by the use of standard transportation aging and disposal canisters (STADs), early or late start of the repository, and the repository emplacement thermal power limits. The impacts were evaluated with regard to the availability of the DPCs for emplacement, achievable repository acceptance rates, additional storage required at an interim storage facility (ISF) and additional emplacement time compared to the corresponding repackaging scenarios, and fuel age at emplacement. The result of this analysis demonstrated that the biggest difference in the availability ofmore » UNF for emplacement between the DPC-only loading scenario and the DPCs and STADs loading scenario is for a repository start date of 2036 with a 6 kW thermal power limit. The differences are also seen in the availability of UNF for emplacement between the DPC-only loading scenario and the DPCs and STADs loading scenario for the alternative with a 6 kW thermal limit and a 2048 start date, and for the alternatives with a 10 kW thermal limit and 2036 and 2048 start dates. The alternatives with disposal of UNF in both DPCs and STADs did not require additional storage, regardless of the repository acceptance rate, as compared to the reference repackaging case. In comparison to the reference repackaging case, alternatives with the 18 kW emplacement thermal limit required little to no additional emplacement time, regardless of the repository start time, the fuel loading scenario, or the repository acceptance rate. Alternatives with the 10 kW emplacement thermal limit and the DPCs and STADs fuel loading scenario required some additional emplacement time. The most significant decrease in additional emplacement time occurred in the alternative with the 6 kW thermal limit and the 2036 repository starting date. The average fuel age at emplacement ranges from 46 to 88 years. The maximum fuel age at emplacement ranges from 81 to 146 years. The difference in the average and maximum age of fuel at emplacement between the DPC-only and the DPCs and STADs fuel loading scenarios becomes less significant as the repository thermal limit increases and as the repository start date increases. In general, the role of STADs is to store young (30 year or younger) high burnup (45 GWD/MTU or higher) fuel. Recommendations for future study include detailed evaluation of the feasible alternatives with regard to the costs and factors not considered in this analysis, such as worker dose, dose to members of the public, and economic benefits to host entities. It is also recommended to conduct an additional analysis to evaluate the assumption regarding the transportability and disposability of DPCs for the next iteration of the direct disposal of DPCs study.« less

  6. Electric Power Infrastructure Reliability and Security (EPIRS) Reseach and Development Initiative

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Rick Meeker; L. Baldwin; Steinar Dale

    2010-03-31

    Power systems have become increasingly complex and face unprecedented challenges posed by population growth, climate change, national security issues, foreign energy dependence and an aging power infrastructure. Increased demand combined with increased economic and environmental constraints is forcing state, regional and national power grids to expand supply without the large safety and stability margins in generation and transmission capacity that have been the rule in the past. Deregulation, distributed generation, natural and man-made catastrophes and other causes serve to further challenge and complicate management of the electric power grid. To meet the challenges of the 21st century while also maintainingmore » system reliability, the electric power grid must effectively integrate new and advanced technologies both in the actual equipment for energy conversion, transfer and use, and in the command, control, and communication systems by which effective and efficient operation of the system is orchestrated - in essence, the 'smart grid'. This evolution calls for advances in development, integration, analysis, and deployment approaches that ultimately seek to take into account, every step of the way, the dynamic behavior of the system, capturing critical effects due to interdependencies and interaction. This approach is necessary to better mitigate the risk of blackouts and other disruptions and to improve the flexibility and capacity of the grid. Building on prior Navy and Department of Energy investments in infrastructure and resources for electric power systems research, testing, modeling, and simulation at the Florida State University (FSU) Center for Advanced Power Systems (CAPS), this project has continued an initiative aimed at assuring reliable and secure grid operation through a more complete understanding and characterization of some of the key technologies that will be important in a modern electric system, while also fulfilling an education and outreach mission to provide future energy workforce talent and support the electric system stakeholder community. Building upon and extending portions of that research effort, this project has been focused in the following areas: (1) Building high-fidelity integrated power and controls hardware-in-the-loop research and development testbed capabilities (Figure 1). (2) Distributed Energy Resources Integration - (a) Testing Requirements and Methods for Fault Current Limiters, (b) Contributions to the Development of IEEE 1547.7, (c) Analysis of a STATCOM Application for Wind Resource Integration, (d) Development of a Grid-Interactive Inverter with Energy Storage Elements, (e) Simulation-Assisted Advancement of Microgrid Understanding and Applications; (3) Availability of High-Fidelity Dynamic Simulation Tools for Grid Disturbance Investigations; (4) HTS Material Characterization - (a) AC Loss Studies on High Temperature Superconductors, (b) Local Identification of Current-Limiting Mechanisms in Coated Conductors; (5) Cryogenic Dielectric Research; and (6) Workshops, education, and outreach.« less

  7. Extreme ground motions and Yucca Mountain

    USGS Publications Warehouse

    Hanks, Thomas C.; Abrahamson, Norman A.; Baker, Jack W.; Boore, David M.; Board, Mark; Brune, James N.; Cornell, C. Allin; Whitney, John W.

    2013-01-01

    Yucca Mountain is the designated site of the underground repository for the United States' high-level radioactive waste (HLW), consisting of commercial and military spent nuclear fuel, HLW derived from reprocessing of uranium and plutonium, surplus plutonium, and other nuclear-weapons materials. Yucca Mountain straddles the western boundary of the Nevada Test Site, where the United States has tested nuclear devices since the 1950s, and is situated in an arid, remote, and thinly populated region of Nevada, ~100 miles northwest of Las Vegas. Yucca Mountain was originally considered as a potential underground repository of HLW because of its thick units of unsaturated rocks, with the repository horizon being not only ~300 m above the water table but also ~300 m below the Yucca Mountain crest. The fundamental rationale for a geologic (underground) repository for HLW is to securely isolate these materials from the environment and its inhabitants to the greatest extent possible and for very long periods of time. Given the present climate conditions and what is known about the current hydrologic system and conditions around and in the mountain itself, one would anticipate that the rates of infiltration, corrosion, and transport would be very low—except for the possibility that repository integrity might be compromised by low-probability disruptive events, which include earthquakes, strong ground motion, and (or) a repository-piercing volcanic intrusion/eruption. Extreme ground motions (ExGM), as we use the phrase in this report, refer to the extremely large amplitudes of earthquake ground motion that arise at extremely low probabilities of exceedance (hazard). They first came to our attention when the 1998 probabilistic seismic hazard analysis for Yucca Mountain was extended to a hazard level of 10-8/yr (a 10-4/yr probability for a 104-year repository “lifetime”). The primary purpose of this report is to summarize the principal results of the ExGM research program as they have developed over the past 5 years; what follows will be focused on Yucca Mountain, but not restricted to it.

  8. Construction of quality-assured infant feeding process of care data repositories: Construction of the perinatal repository (Part 2).

    PubMed

    García-de-León-Chocano, Ricardo; Muñoz-Soler, Verónica; Sáez, Carlos; García-de-León-González, Ricardo; García-Gómez, Juan M

    2016-04-01

    This is the second in a series of two papers regarding the construction of data quality (DQ) assured repositories, based on population data from Electronic Health Records (EHR), for the reuse of information on infant feeding from birth until the age of two. This second paper describes the application of the computational process of constructing the first quality-assured repository for the reuse of information on infant feeding in the perinatal period, with the aim of studying relevant questions from the Baby Friendly Hospital Initiative (BFHI) and monitoring its deployment in our hospital. The construction of the repository was carried out using 13 semi-automated procedures to assess, recover or discard clinical data. The initial information consisted of perinatal forms from EHR related to 2048 births (Facts of Study, FoS) between 2009 and 2011, with a total of 433,308 observations of 223 variables. DQ was measured before and after the procedures using metrics related to eight quality dimensions: predictive value, correctness, duplication, consistency, completeness, contextualization, temporal-stability, and spatial-stability. Once the predictive variables were selected and DQ was assured, the final repository consisted of 1925 births, 107,529 observations and 73 quality-assured variables. The amount of discarded observations mainly corresponds to observations of non-predictive variables (52.90%) and the impact of the de-duplication process (20.58%) with respect to the total input data. Seven out of thirteen procedures achieved 100% of valid births, observations and variables. Moreover, 89% of births and ~98% of observations were consistent according to the experts׳ criteria. A multidisciplinary approach along with the quantification of DQ has allowed us to construct the first repository about infant feeding in the perinatal period based on EHR population data. Copyright © 2016 Elsevier Ltd. All rights reserved.

  9. 78 FR 57799 - National Oil and Hazardous Substances Pollution Contingency Plan National Priorities List

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-20

    ..., including a Responsiveness Summary, if prepared, in the Site repositories. DATES: This withdrawal of the.... ADDRESSES: Information Repositories: Comprehensive information on the Site, as well as the comments that we...

  10. 10 CFR 960.3-2-2-5 - Formal site nomination.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... NUCLEAR WASTE REPOSITORY Implementation Guidelines § 960.3-2-2-5 Formal site nomination. After the final... determines suitable for site characterization for the selection of a repository site, and, in so doing, he...

  11. Method for storing spent nuclear fuel in repositories

    DOEpatents

    Schweitzer, Donald G.; Sastre, Cesar; Winsche, Warren

    1981-01-01

    A method for storing radioactive spent fuel in repositories containing sulfur as the storage medium is disclosed. Sulfur is non-corrosive and not subject to radiation damage. Thus, storage periods of up to 100 years are possible.

  12. 77 FR 59338 - National Oil and Hazardous Substances Pollution Contingency Plan; National Priorities List

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-09-27

    ... Responsiveness Summary, if prepared, in the Site repositories. DATES: Effective Date: This withdrawal of the.... ADDRESSES: Information Repositories: Comprehensive information on the Site, as well as the comments that we...

  13. 10 CFR 960.3-1-2 - Diversity of rock types.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... NUCLEAR WASTE REPOSITORY Implementation Guidelines § 960.3-1-2 Diversity of rock types. Consideration shall be given to a variety of geologic media in which sites for the development of repositories may be...

  14. 10 CFR 960.3-2-2-4 - The environmental assessment.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... FOR A NUCLEAR WASTE REPOSITORY Implementation Guidelines § 960.3-2-2-4 The environmental assessment...; and an assessment of the regional and local impacts of locating a repository at the site. The draft...

  15. Method for storing spent nuclear fuel in repositories

    DOEpatents

    Schweitzer, D.G.; Sastre, C.; Winsche, W.

    A method for storing radioactive spent fuel in repositories containing sulfur as the storage medium is disclosed. Sulfur is non-corrosive and not subject to radiation damage. Thus, storage periods of up to 100 years are possible.

  16. 10 CFR 960.3-1-4 - Evidence for siting decisions.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... NUCLEAR WASTE REPOSITORY Implementation Guidelines § 960.3-1-4 Evidence for siting decisions. The siting... recommendation of a candidate site for the development of a repository. Each of these decisions will be supported...

  17. Visualizing research collections in the National Transportation Library's digital repository : ROSA P.

    DOT National Transportation Integrated Search

    2017-01-01

    The National Transportation Library's (NTL) Repository and Open Science Portal (ROSA P) : is a digital library for transportation, including U. S. Department of Transportation : sponsored research results and technical publications, other documents a...

  18. Topic I: Induced changes in hydrology at low-level radioactive waste repository sites: A section in Safe disposal of radionuclides in low-level radioactive-waste repository sites; Low-level radioactive-waste disposal workshop, U.S. Geological Survey, July 11-16, 1987, Big Bear Lake, Calif., Proceedings (Circular 1036)

    USGS Publications Warehouse

    Prudic, David E.; Dennehy, Kevin F.; Bedinger, Marion S.; Stevens, Peter R.

    1990-01-01

    Engineering practices, including the excavation of trenches, placement of waste, nature of waste forms, backfilling procedures and materials, and trench-cover construction and materials at low-level radioactive-waste repository sites greatly affect the geohydrology of the sites. Engineering practices are dominant factors in eventual stability and isolation of the waste. The papers presented relating to Topic I were discussions of the hydrogeologic setting at existing low-level radioactive-waste repository sites and changes in the hydrology induced by site operations. Papers summarizing detailed studies presented at this workshop include those at sites near Sheffield, Ill.; Oak Ridge National Laboratory, Tenn.; West Valley, N.Y.; Maxey Flats, Ky.; Barnwell, S.C.; and Beatty, Nev. 

  19. Developing criteria to establish Trusted Digital Repositories

    USGS Publications Warehouse

    Faundeen, John L.

    2017-01-01

    This paper details the drivers, methods, and outcomes of the U.S. Geological Survey’s quest to establish criteria by which to judge its own digital preservation resources as Trusted Digital Repositories. Drivers included recent U.S. legislation focused on data and asset management conducted by federal agencies spending $100M USD or more annually on research activities. The methods entailed seeking existing evaluation criteria from national and international organizations such as International Standards Organization (ISO), U.S. Library of Congress, and Data Seal of Approval upon which to model USGS repository evaluations. Certification, complexity, cost, and usability of existing evaluation models were key considerations. The selected evaluation method was derived to allow the repository evaluation process to be transparent, understandable, and defensible; factors that are critical for judging competing, internal units. Implementing the chosen evaluation criteria involved establishing a cross-agency, multi-disciplinary team that interfaced across the organization. 

  20. Geologic, geochemical rock mechanics and hydrologic characteristics of candidate repository horizons

    NASA Astrophysics Data System (ADS)

    Long, P. E.; Apted, M. J.; Spane, F. A., Jr.; Kim, K.

    1982-09-01

    The feasibility of constructing a nuclear waste repository in basalt (NWRB) on the Hanford Site is determined. Studies conducted indicate feasibility and performance requirements are within a significant safety margin. The two most promising candidate repository horizons for an NWRB are the middle Sentinel Bluffs and the Umtanum flows. Both of these flows are laterally continuous and have thicknesses of competent rock adequate to accommodate a repository. Significant geologic differences between the two flows are their depth, total thickness, and variability of flow top thickness. These differences are considered in selection of one of the two flows for breakout from an exploratory shaft. The geochemical characteristics of both the middle Sentinel Bluffs flow and the Umtanum flow favor long term isolation of radionuclides by providing an environment in which canister corrosion rates and solubility of many radionuclide bearing solids is relatively low.

Top