Search and Evaluation of Learning Materials for Ophthalmology, 1973-1975.

ERIC Educational Resources Information Center

Prince, Arlene Leinbach; And Others

A study of instructional materials, especially media, available for ophthalmology teaching was initiated at the University of Washington School of Medicine in March 1973. Some 115 catalog and distribution sources were contracted, from which more than 200 potential titles were identified. Fifty three materials were reviewed and evaluated. Six…

Exploration of Novel Materials for Development of Next Generation OPV Devices: Cooperative Research and Development Final Report, CRADA Number CRD-10-398

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olson, D.

2012-09-01

Organic-based solar cells offer the potential for low cost, scalable conversion of solar energy. This project will try to utilize the extensive organic synthetic capabilities of ConocoPhillips to produce novel acceptor and donor materials as well potentially as interface modifiers to produce improved OPV devices with greater efficiency and stability. The synthetic effort will be based on the knowledge base and modeling being done at NREL to identify new candidate materials.

Potentiodynamic Corrosion Testing.

PubMed

Munir, Selin; Pelletier, Matthew H; Walsh, William R

2016-09-04

Different metallic materials have different polarization characteristics as dictated by the open circuit potential, breakdown potential, and passivation potential of the material. The detection of these electrochemical parameters identifies the corrosion factors of a material. A reliable and well-functioning corrosion system is required to achieve this. Corrosion of the samples was achieved via a potentiodynamic polarization technique employing a three-electrode configuration, consisting of reference, counter, and working electrodes. Prior to commencement a baseline potential is obtained. Following the stabilization of the corrosion potential (Ecorr), the applied potential is ramped at a slow rate in the positive direction relative to the reference electrode. The working electrode was a stainless steel screw. The reference electrode was a standard Ag/AgCl. The counter electrode used was a platinum mesh. Having a reliable and well-functioning in vitro corrosion system to test biomaterials provides an in-expensive technique that allows for the systematic characterization of the material by determining the breakdown potential, to further understand the material's response to corrosion. The goal of the protocol is to set up and run an in vitro potentiodynamic corrosion system to analyze pitting corrosion for small metallic medical devices.

Composite Material Application to Liquid Rocket Engines

NASA Technical Reports Server (NTRS)

Judd, D. C.

1982-01-01

The substitution of reinforced plastic composite (RPC) materials for metal was studied. The major objectives were to: (1) determine the extent to which composite materials can be beneficially used in liquid rocket engines; (2) identify additional technology requirements; and (3) determine those areas which have the greatest potential for return. Weight savings, fabrication costs, performance, life, and maintainability factors were considered. Two baseline designs, representative of Earth to orbit and orbit to orbit engine systems, were selected. Weight savings are found to be possible for selected components with the substitution of materials for metal. Various technology needs are identified before RPC material can be used in rocket engine applications.

Intelligent Agents and Their Potential for Future Design and Synthesis Environment

NASA Technical Reports Server (NTRS)

Noor, Ahmed K. (Compiler); Malone, John B. (Compiler)

1999-01-01

This document contains the proceedings of the Workshop on Intelligent Agents and Their Potential for Future Design and Synthesis Environment, held at NASA Langley Research Center, Hampton, VA, September 16-17, 1998. The workshop was jointly sponsored by the University of Virginia's Center for Advanced Computational Technology and NASA. Workshop attendees came from NASA, industry and universities. The objectives of the workshop were to assess the status of intelligent agents technology and to identify the potential of software agents for use in future design and synthesis environment. The presentations covered the current status of agent technology and several applications of intelligent software agents. Certain materials and products are identified in this publication in order to specify adequately the materials and products that were investigated in the research effort. In no case does such identification imply recommendation or endorsement of products by NASA, nor does it imply that the materials and products are the only ones or the best ones available for this purpose. In many cases equivalent materials and products are available and would probably produce equivalent results.

The Use Potential of Traditional Building Materials for the Realization of Structures by Modern Methods of Construction

NASA Astrophysics Data System (ADS)

Spišáková, Marcela; Mačková, Daniela

2015-11-01

The sustainable building has taken off in recent years with many investors looking for new and different methods of construction. The traditional building materials can be made out of natural materials, while others can help to lower energy costs of the occupant once built. Regardless of what the goal of the investor is, traditional building materials and their use is on the rise. The submitted paper provides an overview of natural building materials and possible modern building systems using these construction materials. Based on the questionnaire survey is defined the use potential of traditional building materials for the realization of the construction by methods of modern constructions and then are determined the drivers and barriers of traditional materials through using modern methods of construction. Considering the analysis of the achieved results, we can identify the gaps in the construction market in Slovakia and also to assess the perception of potential investors in the field of traditional building materials use, which is the purpose of submitted paper.

Novel Application of FTIR Spectroscopy for the Passive Standoff Detection of Radiological Materials

DTIC Science & Technology

2006-08-01

possibility of applying the long-wave passive standoff detection technique to the identification of radiological materials. This work is based on...infrared (FTIR) radiometry is a well-known technique for detecting and identifying chemical warfare agents. In addition to these potential threats...necessary tools and techniques available for detecting and identifying radioactive products. At present, the main detection techniques depend on methods

Emerging Science and Research Opportunities for Metals and Metallic Nanostructures: A Report on the NSF MMN Workshop

NASA Astrophysics Data System (ADS)

Pollock, Tresa; Handwerker, Carol

In the next decade, fundamental research in metals and metallic nanostructures (MMN) has the potential to continue to transform science into innovative materials, devices, and systems. This talk summarizes the findings of a workshop to identify emerging and potentially transformative research areas in MMN. The metals and metallic nanostructures (MMNs) workshop aimed to identify significant research trends, scientific fundamentals, and recent breakthroughs that can enable new or enhanced MMN performance, either alone or in a more complex materials system, for a wide range of applications. Additionally, the role that MMN research can play in high-priority research and development (R&D) areas such as the U.S. Materials Genome Initiative, the National Nanotechnology Initiative, the Advanced Manufacturing Initiative, and other similar initiatives that exist internationally was assessed. The workshop also addressed critical issues related to materials research instrumentation and the cyberinfrastructure for materials science research and education, as well as science, technology, engineering, and mathematics (STEM) workforce development, with emphasis on the United States but with an appreciation that similar challenges and opportunities for the materials community exist internationally.

Exploration of GPS to enhance the safe transport of hazardous materials

DOT National Transportation Integrated Search

1997-12-01

The report (1) documents a set of requirements for the performance of location systems that utilize the Global Positioning System (GPS), (2) identifies potential uses of GPS in hazardous materials transport, (3) develops service descriptions for the ...

Survival of Xanthomonas fragariae on common materials found in strawberry nurseries

USDA-ARS?s Scientific Manuscript database

Xanthomonas fragariae causes strawberry angular leaf spot, an important disease in strawberry nursery production. To identify potential inoculum sources, the ability of X. fragariae to survive was examined on 10 common materials typically associated with strawberry nurseries (cardboard, glass, latex...

From source material to news story in New Zealand print media: a prospective study of the stigmatizing processes in depicting mental illness.

PubMed

Nairn, R; Coverdale, J; Claasen, D

2001-10-01

The aim of this study was to analyse how newspaper articles that depict mental illnesses are generated from source materials. From a prospectively collected national sample of print materials involving mental illness, 50 published items that related to the Privacy Commissioner's opinion about disclosure of a psychiatric patient's health information were identified. A copy of the Privacy Commissioner's original Case Note and three news stories about the Case Note distributed by the New Zealand Press Association constituted the database. These materials were subjected to discourse analysis. We identified themes and their transformation from the Case Note through the news stories and examined the impact of these transformations on the stigmatization of mental illness. Four themes were identified: human rights, vulnerability, risk of dangerousness and threat, and mental illness/psychiatric patient. The only potentially positive theme, human rights, was limited both by being fragmented in the source material, and by being utilized, in the published news stories to undermine the legitimacy of the patient's right to privacy. Use of the other themes was consistent with stereotypes about mental illness. Although there were no inaccuracies in the content of the news stories they were substantially more negative than the source material in their depiction of the identified patient. A potentially positive discourse (human rights) was not by itself sufficient to ensure a positive portrayal of mental illness. An understanding of the transformations is important for efforts to effectively combat the stigmatization of those with mental illness.

Materials technology assessment for a 1050 K Stirling space engine design

NASA Technical Reports Server (NTRS)

Scheuermann, Coulson M.; Dreshfield, Robert L.; Gaydosh, Darrell J.; Kiser, James D.; Mackay, Rebecca A.; Mcdaniels, David L.; Petrasek, Donald W.; Vannucci, Raymond D.; Bowles, Kenneth J.; Watson, Gordon K.

1988-01-01

An assessment of materials technology and proposed materials selection was made for the 1050 K (superalloy) Stirling Space Engine design. The objectives of this assessment were to evaluate previously proposed materials selections, evaluate the current state-of-the-art materials, propose potential alternate materials selections and identify research and development efforts needed to provide materials that can meet the stringent system requirements. This assessment generally reaffirmed the choices made by the contractor. However, in many cases alternative choices were described and suggestions for needed materials and fabrication research and development were made.

THE FEASIBILITY OF UTILIZING SOLID WASTES FOR BUILDING MATERIALS. EXECUTIVE SUMMARY

EPA Science Inventory

This report focuses on two phases of a suggested four phase study to evaluate the technological and commercial possibilities of waste - derived composites. The first phase involved a joint and comprehensive literature search to identify wastes with potential as building materials...

Identifying and Dealing with Hazardous Materials and Procedures in the General Chemistry Laboratory.

ERIC Educational Resources Information Center

Katz, David A.

1982-01-01

A survey of freshman chemistry laboratory manuals identified 15 questionable laboratory procedures, including the use of potentially hazardous chemicals. Alternatives are suggested for each hazard discussed (such as using a substitute solvent for benzene). (SK)

Nontargeted multicomponent analytical screening of plastic food contact materials using fast interpretation of deliverables via expert structure-activity relationship software.

PubMed

Rothenbacher, Thorsten; Schwack, Wolfgang

2009-01-01

Plastic packaging materials may release compounds into packed foodstuffs. To identify potential migrants of toxicological concern, resins, and multilayer foils (mainly polyethylene) intended for the production of food contact materials were extracted and analyzed by GC/mass spectrometry. To identify even compounds of low concentrations, AMDIS software was used and data evaluation was safeguarded by the Kovats retention index (RI) system. In this way, 46 compounds were identified as possible migrants. The expert structure-activity relationship software DEREK for Windows was utilized to evaluate all identified substances in terms of carcinogenicity, genotoxicity, thyroid toxicity, and miscellaneous endpoints for humans. Additionally, a literature search for these compounds was performed with Sci-Finder, but relevant data were missing for 28 substances. Seven compounds with adverse toxicological effects were identified. In addition, the RIs of 24 commercial additive standards, measured with a GC capillary column of intermediate polarity, are given.

NANOSTRUCTURED MATERIAL DESIGN FOR HG, AS, AND SE CAPTURE

EPA Science Inventory

The goal of this research project is to identify potential materials that can be used as multipollutant sorbents using a hierarchy of computational modeling approaches. Palladium (Pd) and gold (Au) alloys were investigated and the results show that the addition of a small amou...

Identification and analysis of factors affecting thermal shock resistance of ceramic materials in solar receivers

NASA Technical Reports Server (NTRS)

Hasselman, D. P. H.; Singh, J. P.; Satyamurthy, K.

1980-01-01

An analysis was conducted of the possible modes of thermal stress failure of brittle ceramics for potential use in point-focussing solar receivers. The pertinent materials properties which control thermal stress resistance were identified for conditions of steady-state and transient heat flow, convective and radiative heat transfer, thermal buckling and thermal fatigue as well as catastrophic crack propagation. Selection rules for materials with optimum thermal stress resistance for a particular thermal environment were identified. Recommendations for materials for particular components were made. The general requirements for a thermal shock testing program quantitatively meaningful for point-focussing solar receivers were outlined. Recommendations for follow-on theoretical analyses were made.

Identifying the material of original and restored parts of a 14^{th} century alabaster annunciation group through stable isotopes

NASA Astrophysics Data System (ADS)

Kloppmann, Wolfram; Leroux, Lise; Le Pogam, Pierre-Yves; Bromblet, Philippe

2017-04-01

The origin of raw materials for sculpture is often obscure before the 17th century due to the scarcity of written sources. Identifying this origin provides hints to economic exchanges but also, potentially, allows for attributing sculptures to a specific context of creation (regional workshops, artists). Another challenge for art historians is the identification of restorations and their potential chronology. We present an example of a 14th century group of two statues, made of gypsum alabaster, representing an annunciation group, with the Virgin Mary and the angel Gabriel. Their original position was a near Troyes in the eastern Paris Basin, they are now separated being conserved at the Louvre Museum (Virgin Mary) and the Cleveland Museum of Art (Gabriel). Our multi-isotope study revealed the common origin of the material used for both sculptures, their isotope fingerprints being identical within the analytical error. These fingerprints are highly specific and point to an origin in a historical gypsum and alabaster quarry in the northern part of Provence, France, first mentioned at the end of the 13th century. We were also able to identify an unknown restoration of lower part of the Virgin Mary statue with an optically undistinguishable material, using Tuscan alabaster, most likely in the 19th century. This underlines the potential and usefulness of independent geochemical evidence to underpin stylistic hypotheses on grouping of individual artworks, historical economic relationships between regions and on past restoration activities.

Cryogenic Model Materials

NASA Technical Reports Server (NTRS)

Kimmel, W. M.; Kuhn, N. S.; Berry, R. F.; Newman, J. A.

2001-01-01

An overview and status of current activities seeking alternatives to 200 grade 18Ni Steel CVM alloy for cryogenic wind tunnel models is presented. Specific improvements in material selection have been researched including availability, strength, fracture toughness and potential for use in transonic wind tunnel testing. Potential benefits from utilizing damage tolerant life-prediction methods, recently developed fatigue crack growth codes and upgraded NDE methods are also investigated. Two candidate alloys are identified and accepted for cryogenic/transonic wind tunnel models and hardware.

Interior Head Impact Protective Components and Materials for Use in US Army Vehicles

DTIC Science & Technology

2015-08-01

benchmarked the automotive industry to identify potential commercial-off-the-shelf (COTS) materials. TARDEC initially tested the energy attenuating...this effort leverages the performance criterion used in the automotive industry according to SAE TP201U-01, FMVSS (Federal Motor Vehicle Safety...of the core material not being fully engaged on the Ancra tract. The backing of material ID 14 was reinforced with steel , this resulted in the

IDENTIFYING POTENTIAL SOURCES OF BACKGROUND CONTAMINATION IN RT-PCR

EPA Science Inventory

Extraction of nucleic acids from low biomass samples, such as drinking water, is particularly sensitive to potential background contamination because the contaminating material is minimally diluted by the sample. The presence of bacterial DNA in Taq DNA polymerase is wel...

In vitro Alternative Methodologies for Central Nervous System Assessment: A Critique using Nanoscale Materials as an Example.

EPA Science Inventory

Identifying the potential health hazards to the central nervous system of a new family of materials presents many challenges. Whole-animal toxicity testing has been the tradition, but in vitro methods have been steadily gaining popularity. There are numerous challenges in testing...

Spectral parameters for Dawn FC color data: Carbonaceous chondrites and aqueous alteration products as potential cerean analog materials

NASA Astrophysics Data System (ADS)

Schäfer, Tanja; Nathues, Andreas; Mengel, Kurt; Izawa, Matthew R. M.; Cloutis, Edward A.; Schäfer, Michael; Hoffmann, Martin

2016-02-01

We identified a set of spectral parameters based on Dawn Framing Camera (FC) bandpasses, covering the wavelength range 0.4-1.0 μm, for mineralogical mapping of potential chondritic material and aqueous alteration products on dwarf planet Ceres. Our parameters are inferred from laboratory spectra of well-described and clearly classified carbonaceous chondrites representative for a dark component. We additionally investigated the FC signatures of candidate bright materials including carbonates, sulfates and hydroxide (brucite), which can possibly be exposed on the cerean surface by impact craters or plume activity. Several materials mineralogically related to carbonaceous chondrites, including pure ferromagnesian phyllosilicates, and serpentinites were also investigated. We tested the potential of the derived FC parameters for distinguishing between different carbonaceous chondritic materials, and between other plausible cerean surface materials. We found that the major carbonaceous chondrite groups (CM, CO, CV, CK, and CR) are distinguishable using the FC filter ratios 0.56/0.44 μm and 0.83/0.97 μm. The absorption bands of Fe-bearing phyllosilicates at 0.7 and 0.9 μm in terrestrial samples and CM carbonaceous chondrites can be detected by a combination of FC band parameters using the filters at 0.65, 0.75, 0.83, 0.92 and 0.97 μm. This set of parameters serves as a basis to identify and distinguish different lithologies on the cerean surface by FC multispectral data.

SRB thermal curtain design support

NASA Technical Reports Server (NTRS)

Lundblad, Wayne E.

1990-01-01

The objective during this time period was to perform a preliminary thermal analysis using some measured and estimated thermal properties on the angle-interlock materials. This preliminary thermal analysis is to serve as a guide for identifying any potential problems in blanket construction and identifying future tests.

Barrier Coatings for Refractory Metals and Superalloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

SM Sabol; BT Randall; JD Edington

2006-02-23

In the closed working fluid loop of the proposed Prometheus space nuclear power plant (SNPP), there is the potential for reaction of core and plant structural materials with gas phase impurities and gas phase transport of interstitial elements between superalloy and refractory metal alloy components during service. Primary concerns are surface oxidation, interstitial embrittlement of refractory metals and decarburization of superalloys. In parallel with kinetic investigations, this letter evaluates the ability of potential coatings to prevent or impede communication between reactor and plant components. Key coating requirements are identified and current technology coating materials are reviewed relative to these requirements.more » Candidate coatings are identified for future evaluation based on current knowledge of design parameters and anticipated environment. Coatings were identified for superalloys and refractory metals to provide diffusion barriers to interstitial transport and act as reactive barriers to potential oxidation. Due to their high stability at low oxygen potential, alumina formers are most promising for oxidation protection given the anticipated coolant gas chemistry. A sublayer of iridium is recommended to provide inherent diffusion resistance to interstitials. Based on specific base metal selection, a thin film substrate--coating interdiffusion barrier layer may be necessary to meet mission life.« less

Potential of Organic Matrix Composites for Liquid Oxygen Tank

NASA Technical Reports Server (NTRS)

Davis, Samuel E.; Herald, Stephen D.; Stolzfus, Joel M.; Engel, Carl D.; Bohlen, James W.; Palm, Tod; Robinson, Michael J.

2005-01-01

Composite materials are being considered for the tankage of cryogenic propellants in access to space because of potentially lower structural weights. A major hurdle for composites is an inherent concern about the safety of using flammable structural materials in contact with liquid and gaseous oxygen. A hazards analysis approach addresses a series of specific concerns that must be addressed based upon test data. Under the 2nd Generation Reusable Launch Vehicle contracts, testing was begun for a variety of organic matrix composite materials both to aid in the selection of materials and to provide needed test data to support hazards analyses. The work has continued at NASA MSFC and the NASA WSTF to provide information on the potential for using composite materials in oxygen systems. Appropriate methods for oxygen compatibility testing of structural materials and data for a range of composite materials from impact, friction, flammability and electrostatic discharge testing are presented. Remaining concerns and conclusions about composite tank structures, and recommendations for additional testing are discussed. Requirements for system specific hazards analysis are identified.

Voltage-induced switching of an antiferromagnetically ordered topological Dirac semimetal

NASA Astrophysics Data System (ADS)

Kim, Youngseok; Kang, Kisung; Schleife, André; Gilbert, Matthew J.

2018-04-01

An antiferromagnetic semimetal has been recently identified as a new member of topological semimetals that may host three-dimensional symmetry-protected Dirac fermions. A reorientation of the Néel vector may break the underlying symmetry and open a gap in the quasiparticle spectrum, inducing the (semi)metal-insulator transition. Here, we predict that such a transition may be controlled by manipulating the chemical potential location of the material. We perform both analytical and numerical analysis on the thermodynamic potential of the model Hamiltonian and find that the gapped spectrum is preferred when the chemical potential is located at the Dirac point. As the chemical potential deviates from the Dirac point, the system shows a possible transition from the gapped to the gapless phase and switches the corresponding Néel vector configuration. We perform density functional theory calculations to verify our analysis using a realistic material and discuss a two terminal transport measurement as a possible route to identify the voltage-induced switching of the Néel vector.

Identifying and quantifying short-lived fission products from thermal fission of HEU using portable HPGe detectors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pierson, Bruce D.; Finn, Erin C.; Friese, Judah I.

2013-03-01

Due to the emerging potential for trafficking of special nuclear material, research programs are investigating current capabilities of commercially available portable gamma ray detection systems. Presented in this paper are the results of three different portable high-purity germanium (HPGe) detectors used to identify short-lived fission products generated from thermal neutron interrogation of small samples of highly enriched uranium. Samples were irradiated at the Washington State University (WSU) Nuclear Radiation Center’s 1MW TRIGA reactor. The three portable, HPGe detectors used were the ORTEC MicroDetective, the ORTEC Detective, and the Canberra Falcon. Canberra’s GENIE-2000 software was used to analyze the spectral datamore » collected from each detector. Ultimately, these three portable detectors were able to identify a large range of fission products showing potential for material discrimination.« less

Market-Smart Deconstruction and Material Recovery at Brownfield Sites: How to Identify and Reuse Existing Materials Found at Brownfield Sites

DTIC Science & Technology

2011-06-01

efforts to assess , remediate, and sustainably reuse brownfields . This project is based on the premise that communities have finite resources and that the...this work is to develop tools and guidance for brownfields partners to assess the potential of extracting construction material assets from...buildings, structures, and infrastructure on brownfield sites, and to reuse or recycle this material. This assessment will address the physical

Enhanced thermoelectric performance driven by high-temperature phase transition in the phase change material Ge 4SbTe 5

DOE PAGES

Williams, Jared B.; Lara-Curzio, Edgar; Cakmak, Ercan; ...

2015-05-15

Phase change materials are identified for their ability to rapidly alternate between amorphous and crystalline phases and have large contrast in the optical/electrical properties of the respective phases. The materials are primarily used in memory storage applications, but recently they have also been identified as potential thermoelectric materials. Many of the phase change materials researched today can be found on the pseudo-binary (GeTe) 1-x(Sb 2Te 3) x tie-line. While many compounds on this tie-line have been recognized as thermoelectric materials, here we focus on Ge 4SbTe 5, a single phase compound just off of the (GeTe) 1-x(Sb 2Te 3) xmore » tie-line, that forms in a stable rocksalt crystal structure at room temperature. We find that stoichiometric and undoped Ge 4SbTe 5 exhibits a thermal conductivity of ~1.2 W/m-K at high temperature and a large Seebeck coefficient of ~250 μV/K. The resistivity decreases dramatically at 623 K due to a structural phase transition which lends to a large enhancement in both thermoelectric power factor and thermoelectric figure of merit at 823 K. In a more general sense the research presents evidence that phase change materials can potentially provide a new route to highly efficient thermoelectric materials for power generation at high temperature.« less

The feasibility of solar reflector production from lunar materials for solar power in space

NASA Technical Reports Server (NTRS)

1990-01-01

Science Applications International Corporation (SAIC) investigated the feasibility of producing solar reflectors from indigenous lunar materials for solar power production on the moon. First, lunar construction materials and production processes were reviewed, and candidate materials for reflector production were identified. At the same time, lunar environmental conditions were reviewed for their effect on production of concentrators. Next, conceptual designs and fabrication methods were proposed and studied for production of dish concentrators and heliostats. Finally, fabrication testing was performed on small-scale models using earth analogs of lunar materials. Findings from this initial investigation indicate that production of concentrators from lunar materials may be an attractive approach for solar energy production on the moon. Further design and testing are required to determine the best techniques and approaches to optimize this concept. Four materials were identified as having high potential for solar reflector manufacture. These baseline materials were foamed glass, concrete with glass-fiber reinforcement, a glass-fiber/glass-melt composite, and an iron-glass sintered material.

Using social media for support and feedback by mental health service users: thematic analysis of a twitter conversation.

PubMed

Shepherd, Andrew; Sanders, Caroline; Doyle, Michael; Shaw, Jenny

2015-02-19

Internet based social media websites represent a growing space for interpersonal interaction. Research has been conducted in relation to the potential role of social media in the support of individuals with physical health conditions. However, limited research exists exploring such utilisation by individuals with experience of mental health problems. It could be proposed that access to wider support networks and knowledge could be beneficial for all users, although this positive interpretation has been challenged. The present study focusses on a specific discussion as a case study to assess the role of the website www.twitter.com as a medium for interpersonal communication by individuals with experience of mental disorder and possible source of feedback to mental health service providers. An electronic search was performed to identify material contributing to an online conversation entitled #dearmentalhealthprofessionals. Output from the search strategy was combined in such a way that repeated material was eliminated and all individual material anonymised. The remaining textual material was reviewed and combined in a thematic analysis to identify common themes of discussion. 515 unique communications were identified relating to the specified conversation. The majority of the material related to four overarching thematic headings: The impact of diagnosis on personal identity and as a facilitator for accessing care; Balance of power between professional and service user; Therapeutic relationship and developing professional communication; and Support provision through medication, crisis planning, service provision and the wider society. Remaining material was identified as being direct expression of thanks, self-referential in its content relating to the on-going conversation or providing a link to external resources and further discussion. The present study demonstrates the utility of online social media as both a discursive space in which individuals with experience of mental disorder may share information and develop understanding, and a medium of feedback to mental health service providers. Further research is required to establish potential individual benefit from the utilisation of such networks, its suitability as a means of service provision feedback and the potential role for, and user acceptability of, mental health service providers operating within the space.

Mineral resource potential of the Granite Chief Wilderness Study Area, Placer County, California

USGS Publications Warehouse

Harwood, David S.; Federspiel, Francis E.; Cather, Eric E.; Scott, Douglas F.

1982-01-01

Substantial deposits of sand, gravel, and glacial till suitable for construction materials occur within the area, but their inaccessibility and remoteness from major markets preclude their being classified as a resource. No potential for oil, gas, coal, or geothermal resources was identified.

Intermetallic and ceramic matrix composites for 815 to 1370 C (1500 to 2500 F) gas turbine engine applications

NASA Technical Reports Server (NTRS)

Stephens, Joseph R.

1989-01-01

Light weight and potential high temperature capability of intermetallic compounds, such as the aluminides, and structural ceramics, such as the carbides and nitrides, make these materials attractive for gas turbine engine applications. In terms of specific fuel consumption and specific thrust, revolutionary improvements over current technology are being sought by realizing the potential of these materials through their use as matrices combined with high strength, high temperature fibers. The U.S. along with other countries throughout the world have major research and development programs underway to characterize these composites materials; improve their reliability; identify and develop new processing techniques, new matrix compositions, and new fiber compositions; and to predict their life and failure mechanisms under engine operating conditions. The status is summarized of NASA's Advanced High Temperature Engine Materials Technology Program (HITEMP) and the potential benefits are described to be gained in 21st century transport aircraft by utilizing intermetallic and ceramic matrix composite materials.

A Modular Approach to Integrating Biofuels Education into ChE Curriculum Part I--Learning Materials

ERIC Educational Resources Information Center

He, Q. Peter; Wang, Jin; Zhang, Rong; Johnson, Donald; Knight, Andrew; Polala, Ravali

2016-01-01

In view of potential demand for skilled engineers and competent researchers in the biofuels field, we have identified a significant gap between advanced biofuels research and undergraduate biofuels education in chemical engineering. To help bridge this gap, we created educational materials that systematically integrate biofuels technologies into…

Space processing applications bibliography

NASA Technical Reports Server (NTRS)

1978-01-01

This special bibliography lists 724 articles, papers, and reports which discuss various aspects of the use of the space environment for materials science research or for commercial enterprise. The potentialities of space processing and the improved materials processes that are made possible by the unique aspects of the space environment are emphasized. References identified in April, 1978 are cited.

Hypermedia Reading Materials: Undergraduate Perceptions and Features Affecting Their Reading Comprehension

ERIC Educational Resources Information Center

Hamdan, Nurul Adila; Mohamad, Maslawati; Shaharuddin, Shahizan

2017-01-01

Due to the potential of the Internet and blended learning environment, students, especially L2 learners, are often required to read references available online. A study was conducted to identify the perceptions of L2 learners comprising TESL undergraduates towards TESL-related hypermedia reading materials and the factors contributing to their…

Data Mining for New Two- and One-Dimensional Weakly Bonded Solids and Lattice-Commensurate Heterostructures.

PubMed

Cheon, Gowoon; Duerloo, Karel-Alexander N; Sendek, Austin D; Porter, Chase; Chen, Yuan; Reed, Evan J

2017-03-08

Layered materials held together by weak interactions including van der Waals forces, such as graphite, have attracted interest for both technological applications and fundamental physics in their layered form and as an isolated single-layer. Only a few dozen single-layer van der Waals solids have been subject to considerable research focus, although there are likely to be many more that could have superior properties. To identify a broad spectrum of layered materials, we present a novel data mining algorithm that determines the dimensionality of weakly bonded subcomponents based on the atomic positions of bulk, three-dimensional crystal structures. By applying this algorithm to the Materials Project database of over 50,000 inorganic crystals, we identify 1173 two-dimensional layered materials and 487 materials that consist of weakly bonded one-dimensional molecular chains. This is an order of magnitude increase in the number of identified materials with most materials not known as two- or one-dimensional materials. Moreover, we discover 98 weakly bonded heterostructures of two-dimensional and one-dimensional subcomponents that are found within bulk materials, opening new possibilities for much-studied assembly of van der Waals heterostructures. Chemical families of materials, band gaps, and point groups for the materials identified in this work are presented. Point group and piezoelectricity in layered materials are also evaluated in single-layer forms. Three hundred and twenty-five of these materials are expected to have piezoelectric monolayers with a variety of forms of the piezoelectric tensor. This work significantly extends the scope of potential low-dimensional weakly bonded solids to be investigated.

Recent progress on biodegradable materials and transient electronics.

PubMed

Li, Rongfeng; Wang, Liu; Kong, Deying; Yin, Lan

2018-09-01

Transient electronics (or biodegradable electronics) is an emerging technology whose key characteristic is an ability to dissolve, resorb, or physically disappear in physiological environments in a controlled manner. Potential applications include eco-friendly sensors, temporary biomedical implants, and data-secure hardware. Biodegradable electronics built with water-soluble, biocompatible active and passive materials can provide multifunctional operations for diagnostic and therapeutic purposes, such as monitoring intracranial pressure, identifying neural networks, assisting wound healing process, etc. This review summarizes the up-to-date materials strategies, manufacturing schemes, and device layouts for biodegradable electronics, and the outlook is discussed at the end. It is expected that the translation of these materials and technologies into clinical settings could potentially provide vital tools that are beneficial for human healthcare.

Ferroelectricity in corundum derivatives

NASA Astrophysics Data System (ADS)

Ye, Meng; Vanderbilt, David

The search for new ferroelectric (FE) materials holds promise for broadening our understanding of FE mechanisms and extending the range of application of FE materials. The known FE materials LiNbO3 can be regarded as derived from the A2O3 corundum structure with cation ordering. Here we consider more general binary (AB O3) and ternary (A2 BB' O6) corundum derivatives as an extended class of potential FE materials, motivated by the fact that some members of this class have recently been synthesized. There are four structure types for these corundum derivatives, and the number of cation combinations is enormous, but in many cases the energy barriers for polarization reversal may be too large to allow FE behavior. Here we present a first-principles study of the polar structure, coherent FE barrier, and domain-wall switching barrier for a representative set of polar corundum derivatives, allowing us to identify several potentially new FE materials. We also discuss the conditions under which ferroelectricity is compatible with magnetic ordering. Finally, we identify several empirical measures that can provide a rule of thumb for estimating the barrier energies. Our results should assist in the experimental search for new FE materials in the corundum derivative family. This work is supported by ONR Grant No. N-00014-12-1-1035.

Cutaneous exposure scenarios for engineered nanoparticles used in semiconductor fabrication: a preliminary investigation of workplace surface contamination.

PubMed

Shepard, Michele; Brenner, Sara

2014-01-01

Numerous studies are ongoing in the fields of nanotoxicology and exposure science; however, gaps remain in identifying and evaluating potential exposures from skin contact with engineered nanoparticles in occupational settings. The aim of this study was to identify potential cutaneous exposure scenarios at a workplace using engineered nanoparticles (alumina, ceria, amorphous silica) and evaluate the presence of these materials on workplace surfaces. Process review, workplace observations, and preliminary surface sampling were conducted using microvacuum and wipe sample collection methods and transmission electron microscopy with elemental analysis. Exposure scenarios were identified with potential for incidental contact. Nanoparticles of silica or silica and/or alumina agglomerates (or aggregates) were identified in surface samples from work areas where engineered nanoparticles were used or handled. Additional data are needed to evaluate occupational exposures from skin contact with engineered nanoparticles; precautionary measures should be used to minimize potential cutaneous exposures in the workplace.

Identifying and Solving Lead Issues from Water Systems with Materials/Device Replacement in Schools and other Buildings

EPA Science Inventory

Identifying and assessing lead contamination and exposure potential in single-family residences is difficult enough, but doing the same kind of assessment and remediation in buildings, schools, and day care centers is even more challenging. It is of particular importance because ...

Identifying and Solving Lead Issues from Water Systems with Materials/Device Replacement in Schools and other Buildings - slides

EPA Science Inventory

Identifying and assessing lead contamination and exposure potential in single-family residences is difficult enough, but doing the same kind of assessment and remediation in buildings, schools, and day care centers is even more challenging. It is of particular importance because ...

Multiscale Modeling, Simulation and Visualization and Their Potential for Future Aerospace Systems

NASA Technical Reports Server (NTRS)

Noor, Ahmed K. (Compiler)

2002-01-01

This document contains the proceedings of the Training Workshop on Multiscale Modeling, Simulation and Visualization and Their Potential for Future Aerospace Systems held at NASA Langley Research Center, Hampton, Virginia, March 5 - 6, 2002. The workshop was jointly sponsored by Old Dominion University's Center for Advanced Engineering Environments and NASA. Workshop attendees were from NASA, other government agencies, industry, and universities. The objectives of the workshop were to give overviews of the diverse activities in hierarchical approach to material modeling from continuum to atomistics; applications of multiscale modeling to advanced and improved material synthesis; defects, dislocations, and material deformation; fracture and friction; thin-film growth; characterization at nano and micro scales; and, verification and validation of numerical simulations, and to identify their potential for future aerospace systems.

Thermal Protection Systems: Past, Present and Future

NASA Technical Reports Server (NTRS)

Johnson, Sylvia M.

2015-01-01

Thermal protection materials and systems (TPS) have been critical to fulfilling humankinds desire to explore space. Composite and ceramic materials have enabled the early missions to orbit, the moon, the space station, Mars with robots, and sample return. Crewed missions to Mars are being considered, and this places even more demands on TPS materials. This talk will give some history on the materials used for earth and planetary entry and the demands placed upon such materials. TPS needs for future missions, especially to Mars, will be identified and potential solutions discussed.

AN OBSERVATIONAL STUDY ON THE POTENTIAL EXPOSURES OF 111 PRESCHOOL CHILDREN TO PHTHALATES IN THEIR EVERYDAY ENVIRONMENTS

EPA Science Inventory

The purpose of this work was to identify potential sources and routes of preschool children exposures to two phthalate diesters used in household and personal care products and building materials. Exposure and biomonitoring data was reviewed. The abstract included the preliminary...

Compatibility of Space Nuclear Power Plant Materials in an Inert He/Xe Working Gas Containing Reactive Impurities

DOE Office of Scientific and Technical Information (OSTI.GOV)

MM Hall

2006-01-31

A major materials selection and qualification issue identified in the Space Materials Plan is the potential for creating materials compatibility problems by combining dissimilar reactor core, Brayton Unit and other power conversion plant materials in a recirculating, inert He/Xe gas loop containing reactive impurity gases. Reported here are results of equilibrium thermochemical analyses that address the compatibility of space nuclear power plant (SNPP) materials in high temperature impure He gas environments. These studies provide early information regarding the constraints that exist for SNPP materials selection and provide guidance for establishing test objectives and environments for SNPP materials qualification testing.

Thermal Protection Materials and Systems: Where Have We Been, Where are We Going?

NASA Technical Reports Server (NTRS)

Johnson, Sylvia M.

2016-01-01

Thermal protection materials and systems (TPS) have been critical to fulfilling humankind's desire to explore space. Composite and ceramic materials have enable the early missions to orbit, the moon, the space station, Mars with robots, and sample return. Crewed missions to Mars are being considered, and this places even more demands on TPS materials. This talk will give some history on the materials used for earth and planetary entry and the demands placed upon such materials. TPs needs for future missions, especially to Mars, will be identified and potential solutions discussed.

Identification of recently handled materials by analysis of latent human fingerprints using infrared spectromicroscopy.

PubMed

Grant, Ashleigh; Wilkinson, T J; Holman, Derek R; Martin, Michael C

2005-09-01

Analysis of fingerprints has predominantly focused on matching the pattern of ridges to a specific person as a form of identification. The present work focuses on identifying extrinsic materials that are left within a person's fingerprint after recent handling of such materials. Specifically, we employed infrared spectromicroscopy to locate and positively identify microscopic particles from a mixture of common materials in the latent human fingerprints of volunteer subjects. We were able to find and correctly identify all test substances based on their unique infrared spectral signatures. Spectral imaging is demonstrated as a method for automating recognition of specific substances in a fingerprint. We also demonstrate the use of attenuated total reflectance (ATR) and synchrotron-based infrared spectromicroscopy for obtaining high-quality spectra from particles that were too thick or too small, respectively, for reflection/absorption measurements. We believe the application of this rapid, nondestructive analytical technique to the forensic study of latent human fingerprints has the potential to add a new layer of information available to investigators. Using fingerprints to not only identify who was present at a crime scene, but also to link who was handling key materials, will be a powerful investigative tool.

NASA Collaborative Approach Mitigates Environmentally-Driven Obsolescence

NASA Technical Reports Server (NTRS)

Greene, Brian; Leeney, Bob; Richards, Joni

2016-01-01

National Aeronautics and Space Administration (NASA) missions, like Department of Defense (DoD) organizations, require the rigorous testing and qualification of critical materials. Obsolescence supply risks created by environmental requirements can affect the cost, schedule and performance of NASA missions and the resilience of critical infrastructure. The NASA Technology Evaluation for Environmental Risk Mitigation (TEERM) Principal Center helps to identify obsolescence supply risks driven by environmental requirements and works proactively with NASA Centers and Programs, the DoD, the European Space Agency (ESA) and other agencies and partners to identify and evaluate environmentally friendly alternatives. TEERM tracks environmental regulations, identifies the potential loss of material availability and works with NASA programs and Centers to evaluate potential impacts through a risk assessment approach. TEERM collaborative projects identify, demonstrate and evaluate commercially viable alternative technologies and materials. A major focus during the Space Shuttle Program was the need to replace ozone depleting substances that were used in spray foam and cleaning applications. The potential obsolescence of coatings containing hexavalent chromium and the risks associated with lead free solder were also of concern for the Space Shuttle and present ongoing risks to new programs such as the Space Launch System. One current project teams NASA and ESA in the evaluation and testing of individual coatings and coating systems as replacements for hexavalent chromium coatings in aerospace applications. The proactive, collaborative approach used by TEERM helps reduce the cost burden on any one team partner, reduces duplication of effort, and enhances the technical quality and overall applicability of the testing and analysis.

Material Compatability with Threshold Limit Value Levels of Monomethyl Hydrazine

DTIC Science & Technology

1988-10-26

supply was house- compressed air conditioned by passing through a series of demisters, a hot Hopcalite catalyst bed, a reciprocating dual-tower...recorded. At the end of a test, the tubing was rinsed with methanol and dried with compressed breathing air . Cleaning the tubing material between tests had...niecessary and identify by block wbr -’Materials were evaluated for potential use as ambient air sample lines for hydrazines. Fluorinated poly- mers

Biosafety practices associated with potential agents of biocrime and biowarfare.

PubMed

Burnett, LouAnn C

2006-12-01

Conducting research in a manner that guards against theft and intentional misuse of biological materials requires a process of hazard identification and risk assessment to most effectively identify and implement a risk management plan. Procedures describing physical security, personnel reliability, and material control and accountability define a security plan for this type of research.

High performance poly(etherketoneketone) (PEKK) composite parts fabricated using Big Area Additive Manufacturing (BAAM) processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kunc, Vlastimil; Kishore, Vidya; Chen, Xun

ORNL collaborated with Arkema Inc. to investigate poly(etherketoneketone) (PEKK) and its composites as potential feedstock material for Big Area Additive Manufacturing (BAAM) system. In this work thermal and rheological properties were investigated and characterized in order to identify suitable processing conditions and material flow behavior for BAAM process.

Reflectance-based skin detection in the short wave infrared band and its application to video

NASA Astrophysics Data System (ADS)

Langston, Tye

2016-10-01

Robust reflectance-based skin detection is a potentially powerful tool for security and search and rescue applications, especially when applied to video. However, to be useful it must be able to account for the variations of human skin, as well as other items in the environment that could cause false detections. This effort focused on identifying a robust skin detection scheme that is appropriate for video application. Skin reflectance was modeled to identify unique skin features and compare them to potential false positive materials. Based on these comparisons, specific wavelength bands were selected and different combinations of two and three optical filters were used for actively identifying skin, as well as identifying and removing potential false positive materials. One wavelength combination (1072/1250 nm) was applied to video using both single- and dual-camera configurations based on its still image performance, as well as its appropriateness for video application. There are several important factors regarding the extension of still image skin detection to video, including light available for detection (solar irradiance and reflectance intensity), overall intensity differences between different optical filters, optical component light loss, frame rate, time lag when switching between filters, image coregistration, and camera auto gain behavior.

Update on NRF Measurements on ^237Np for National Security and Safeguards Applications

NASA Astrophysics Data System (ADS)

Angell, C. T.; Joshi, T.; Yee, R.; Swanberg, E.; Norman, E. B.; Kulp, W. D.; Warren, G.; Hicks, C. L., Jr.; Korbly, S.; Klimenko, A.; Wilson, C.; Bray, T. H.; Copping, R.; Shuh, D. K.

2010-11-01

Nuclear resonance fluorescence (NRF) uses γ rays to excite nuclear levels and measure their properties. This provides a unique isotopic signature, and can be used to identify and assay material. This is particularly important for applications that detect the smuggling of nuclear material or the diversion of fissile material for covert weapon programs, both of which present grave risks to world security. ^237Np presents significant safeguard challenges; it is fissile yet currently has fewer safeguard restrictions potentially making it an attractive material for covert weapon programs. This talk will present the final results of two measurements of NRF on ^237Np using a bremsstrahlung photon source. 15 NRF states have been identified between 1.5 and 2.5 MeV excitation energy.

Performance degradation mechanisms and modes in terrestrial photovoltaic arrays and technology for their diagnosis

NASA Technical Reports Server (NTRS)

Noel, G. T.; Sliemers, F. A.; Derringer, G. C.; Wood, V. E.; Wilkes, K. E.; Gaines, G. B.; Carmichael, D. C.

1978-01-01

Accelerated life-prediction test methodologies have been developed for the validation of a 20-year service life for low-cost photovoltaic arrays. Array failure modes, relevant materials property changes, and primary degradation mechanisms are discussed as a prerequisite to identifying suitable measurement techniques and instruments. Measurements must provide sufficient confidence to permit selection among alternative designs and materials and to stimulate widespread deployment of such arrays. Furthermore, the diversity of candidate materials and designs, and the variety of potential environmental stress combinations, degradation mechanisms and failure modes require that combinations of measurement techniques be identified which are suitable for the characterization of various encapsulation system-cell structure-environment combinations.

Lightweight Materials for Vehicles: Needs, Goals, and Future Technologies

DTIC Science & Technology

2010-08-01

during heating, cooling, and deformation - Developing an improved understanding of the kinetics and mechanisms for tranisition Friction Stir Welding ...technology worthiness - Identify new gaps and opportunities Pre- competitive Research Solicitations and Demonstrations - Identify technology gaps...or processing . Key Technology Gaps Active Research . Gap: Microstructural damage during welding limits potential usefulness - Many

A Novel Approach to Detect Accelerated Aged and Surface-Mediated Degradation in Explosives by UPLC-ESI-MS.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beppler, Christina L

2015-12-01

A new approach was created for studying energetic material degradation. This approach involved detecting and tentatively identifying non-volatile chemical species by liquid chromatography-mass spectrometry (LC-MS) with multivariate statistical data analysis that form as the CL-20 energetic material thermally degraded. Multivariate data analysis showed clear separation and clustering of samples based on sample group: either pristine or aged material. Further analysis showed counter-clockwise trends in the principal components analysis (PCA), a type of multivariate data analysis, Scores plots. These trends may indicate that there was a discrete shift in the chemical markers as the went from pristine to aged material, andmore » then again when the aged CL-20 mixed with a potentially incompatible material was thermally aged for 4, 6, or 9 months. This new approach to studying energetic material degradation should provide greater knowledge of potential degradation markers in these materials.« less

Market projections of cellulose nanomaterial-enabled products-- Part 2: Volume estimates

Treesearch

John Cowie; E.M. (Ted) Bilek; Theodore H. Wegner; Jo Anne Shatkin

2014-01-01

Nanocellulose has enormous potential to provide an important materials platform in numerous product sectors. This study builds on previous work by the same authors in which likely high-volume, low-volume, and novel applications for cellulosic nanomaterials were identified. In particular, this study creates a transparent methodology and estimates the potential annual...

Use of similarity scoring in the development of oral solid dosage forms.

PubMed

Ferreira, Ana P; Olusanmi, Dolapo; Sprockel, Omar; Abebe, Admassu; Nikfar, Faranak; Tobyn, Mike

2016-12-05

In the oral solid dosage form space, material physical properties have a strong impact on the behaviour of the formulation during processing. The ability to identify materials with similar characteristics (and thus expected to exhibit similar behaviour) within the company's portfolio can help accelerate drug development by enabling early assessment and prediction of potential challenges associated with the powder properties of a new active pharmaceutical ingredient. Such developments will aid the production of robust dosage forms, in an efficient manner. Similarity scoring metrics are widely used in a number of scientific fields. This study proposes a practical implementation of this methodology within pharmaceutical development. The developed similarity metrics is based on the Mahalanobis distance. Scanning electron microscopy was used to confirm morphological similarity between the reference material and the closest matches identified by the metrics proposed. The results show that the metrics proposed are able to successfully identify material with similar physical properties. Copyright © 2015 Elsevier B.V. All rights reserved.

Advanced organic composite materials for aircraft structures: Future program

NASA Technical Reports Server (NTRS)

1987-01-01

Revolutionary advances in structural materials have been responsible for revolutionary changes in all fields of engineering. These advances have had and are still having a significant impact on aircraft design and performance. Composites are engineered materials. Their properties are tailored through the use of a mix or blend of different constituents to maximize selected properties of strength and/or stiffness at reduced weights. More than 20 years have passed since the potentials of filamentary composite materials were identified. During the 1970s much lower cost carbon filaments became a reality and gradually designers turned from boron to carbon composites. Despite progress in this field, filamentary composites still have significant unfulfilled potential for increasing aircraft productivity; the rendering of advanced organic composite materials into production aircraft structures was disappointingly slow. Why this is and research and technology development actions that will assist in accelerating the application of advanced organic composites to production aircraft is discussed.

Status and applications of diamond and diamond-like materials: An emerging technology

NASA Technical Reports Server (NTRS)

1990-01-01

Recent discoveries that make possible the growth of crystalline diamond by chemical vapor deposition offer the potential for a wide variety of new applications. This report takes a broad look at the state of the technology following from these discoveries in relation to other allied materials, such as high-pressure diamond and cubic boron nitride. Most of the potential defense, space, and commercial applications are related to diamond's hardness, but some utilize other aspects such as optical or electronic properties. The growth processes are reviewed, and techniques for characterizing the resulting materials' properties are discussed. Crystalline diamond is emphasized, but other diamond-like materials (silicon carbide, amorphous carbon containing hydrogen) are also examined. Scientific, technical, and economic problem areas that could impede the rapid exploitation of these materials are identified. Recommendations are presented covering broad areas of research and development.

A two-stage optimization model for emergency material reserve layout planning under uncertainty in response to environmental accidents.

PubMed

Liu, Jie; Guo, Liang; Jiang, Jiping; Jiang, Dexun; Liu, Rentao; Wang, Peng

2016-06-05

In the emergency management relevant to pollution accidents, efficiency emergency rescues can be deeply influenced by a reasonable assignment of the available emergency materials to the related risk sources. In this study, a two-stage optimization framework is developed for emergency material reserve layout planning under uncertainty to identify material warehouse locations and emergency material reserve schemes in pre-accident phase coping with potential environmental accidents. This framework is based on an integration of Hierarchical clustering analysis - improved center of gravity (HCA-ICG) model and material warehouse location - emergency material allocation (MWL-EMA) model. First, decision alternatives are generated using HCA-ICG to identify newly-built emergency material warehouses for risk sources which cannot be satisfied by existing ones with a time-effective manner. Second, emergency material reserve planning is obtained using MWL-EMA to make emergency materials be prepared in advance with a cost-effective manner. The optimization framework is then applied to emergency management system planning in Jiangsu province, China. The results demonstrate that the developed framework not only could facilitate material warehouse selection but also effectively provide emergency material for emergency operations in a quick response. Copyright © 2016. Published by Elsevier B.V.

Identification of processed Chinese medicinal materials using DNA mini-barcoding.

PubMed

Song, Ming; Dong, Gang-Qiang; Zhang, Ya-Qin; Liu, Xia; Sun, Wei

2017-07-01

Most of Chinese medicinal herbs are subjected to traditional processing procedures, including stir-frying, charring, steaming, boiling, and calcining before they are released into dispensaries. The marketing and identification of processed medicinal materials is a growing issue in the marketplace. However, conventional methods of identification have limitations, while DNA mini-barcoding, based on the sequencing of a short-standardized region, has received considerable attention as a new potential means to identify processed medicinal materials. In the present study, six DNA barcode loci including ITS2, psbA-trnH, rbcL, matK, trnL (UAA) intron and its P6 loop, were employed for the authentication of 45 processed samples belonging to 15 species. We evaluated the amplification efficiency of each locus. We also examined the identification accuracy of the potential mini-barcode locus, of trnL (UAA) intron P6 loop. Our results showed that the five primary barcode loci were successfully amplified in only 8.89%-20% of the processed samples, while the amplification rates of the trnL (UAA) intron P6 loop were higher, at 75.56% successful amplification. We compared the mini-barcode sequences with Genbank using the Blast program. The analysis showed that 45.23% samples could be identified to genus level, while only one sample could be identified to the species level. We conclude that trnL (UAA) p6 loop is a candidate mini-barcode that has shown its potential and may become a universal mini-barcode as complementary barcode for authenticity testing and will play an important role in medicinal materials control. Copyright © 2017 China Pharmaceutical University. Published by Elsevier B.V. All rights reserved.

Investigation of test methods, material properties, and processes for solar cell encapsulants

NASA Technical Reports Server (NTRS)

Willis, P. B.

1983-01-01

A study of potentially useful low cost encapsulation materials for the Flat-Plate Solar Array project is discussed. The goal is to identify, evaluate, test and recommend encapsulant materials and processes for the production of cost-effective, long life solar cell modules. Technical investigations included studies of aging and degradation of candidate encapsulation materials, continued identification of primers for durable bonding of module interfaces, continued evaluation of soil resistant treatments for the sunlit surface of the module and testing of corrosion protective coatings for use low cost mild steel substrates.

Beneficial use of dredged material for habitat creation, enhancement, and restoration in New York-New Jersey Harbor.

PubMed

Yozzo, David J; Wilber, Pace; Will, Robert J

2004-10-01

A comprehensive Dredged Material Management Plan (DMMP) has been developed by the US Army Corps of Engineers, New York District (USACE-NYD) and the Port Authority of New York and New Jersey (PANY/NJ). The primary objective of the DMMP is to identify cost-effective and environmentally acceptable alternatives for the placement of dredged material derived from ongoing and proposed navigation improvements within the PANY/NJ. A significant portion of this dredged material is classified as unsuitable for open-ocean disposal. One suite of alternatives presented within the DMMP is the beneficial use of dredged material for habitat creation, enhancement, and restoration within the NY/NJ Harbor Estuary. Proposed beneficial use/habitat development projects include the use of dredged material for construction of artificial reefs, oyster reef restoration, intertidal wetland and mudflat creation, bathymetric recontouring, filling dead-end canals/basins, creation of bird/wildlife islands, and landfill/brownfields reclamation. Preliminary screening of the proposed beneficial use alternatives identified advantages, disadvantages, potential volumes, and estimated costs associated with each project type. Continued study of the proposed beneficial use alternatives has identified areas of environmental research or technology development where further investigation is warranted.

Making good use of online case study materials.

PubMed

Keefer, Matthew Wilks

2005-07-01

Web-based access to engaging instructional materials for SEE instruction represents an increasingly viable and attractive opportunity for educators. This paper will review research findings that demonstrate important differences in more experienced and novice ethical responses to engaging online materials, including authentic cases, codes, and commentaries. Results demonstrate that experienced ethical thinkers are more likely than novices to appeal to middle level principles that identify professional role-specific obligations (RSO); to make greater use of professional knowledge in order to recognize moral issues and relevant facts; and to employ more 'contextually sensitive' reasoning strategies when crafting resolutions to moral problems--e.g., identify alternative moral issues, assess the moral implications of actions, and provide alternative practical resolutions to conflicts. These findings suggest that when effectively integrated into SEE courses, authentic instructional materials have the potential to effectively challenge students and enhance student learning. However, there is evidence that the uses and benefits of these materials are not well understood. In the second part of this paper, five research-based instructional principles will be identified and discussed that can help SEE instructors better understand how to effectively integrate these materials into their courses.

Chemical hazards database and detection system for Microgravity and Materials Processing Facility (MMPF)

NASA Technical Reports Server (NTRS)

Steele, Jimmy; Smith, Robert E.

1991-01-01

The ability to identify contaminants associated with experiments and facilities is directly related to the safety of the Space Station. A means of identifying these contaminants has been developed through this contracting effort. The delivered system provides a listing of the materials and/or chemicals associated with each facility, information as to the contaminant's physical state, a list of the quantity and/or volume of each suspected contaminant, a database of the toxicological hazards associated with each contaminant, a recommended means of rapid identification of the contaminants under operational conditions, a method of identifying possible failure modes and effects analysis associated with each facility, and a fault tree-type analysis that will provide a means of identifying potential hazardous conditions related to future planned missions.

Power Balance Analysis of the Prototype-Material Plasma Exposure eXperiment

NASA Astrophysics Data System (ADS)

Showers, M. A.; Biewer, T. M.; Caneses, J. F.; Caughman, J. B. O.; Lumsdaine, A.; Owen, L.; Rapp, J.; Youchison, D.; Beers, C. J.; Donovan, D. C.; Kafle, N.; Ray, H. B.

2017-10-01

The Prototype-Material Plasma Exposure eXperiment (Proto-MPEX) is a test bed for the plasma source concept for the planned Material Plasma Exposure eXperiment (MPEX), a steady-state linear device studying plasma material interactions for fusion reactors. A power balance of Proto-MPEX attempts to identify machine operating parameters that will improve Proto-MPEX's performance, potentially impacting the MPEX design concept. A power balance has been performed utilizing an extensive diagnostic suite to identify mechanisms and locations of power loss from the main plasma. The diagnostic package includes infrared cameras, double Langmuir probes, fluoroptic probes, Mach probes, a Thomson scattering diagnostic, a McPherson spectrometer and in-vessel thermocouples. Radiation losses are estimated with absolute calibrated spectroscopic signals. This work was supported by the U.S. D.O.E. contract DE-AC05-00OR22725.

Risk factor for phlebitis: a questionnaire study of nurses' perception.

PubMed

Milutinović, Dragana; Simin, Dragana; Zec, Davor

2015-01-01

to assess nurses' perceptions of risk factors for the development of phlebitis, with a special focus on the perception of phlebitic potentials of some infusion medications and solutions. a cross-sectional questionnaire study, which included a sample of 102 nurses. Nurses recognized some factors that may reduce the incidence of phlebitis; however, more than half of the nurses were unaware that the material and diameter of the cannula can affect the incidence rate of phlebitis. Furthermore,underlying disease and high pH of medications or solutions were identified as potential risk factors, whereas low pH and low osmolality were not. Nurses identified Vancomycin and Benzylpenicillin antibiotics with the strongest phlebitic potential. Among other medications and intravenous fluids, Aminophylline, Amiodaronehydrochloride and Potassium chloride 7.4% were identified as potentially causing phlebitis. predisposing factors for phlebitis relating to patients and administered therapy were identified by nurses, while some cannula related risk factors, in particular its physicochemical properties and the time for cannula replacement, were not fully perceived.

Risk factor for phlebitis: a questionnaire study of nurses' perception

PubMed Central

Milutinović, Dragana; Simin, Dragana; Zec, Davor

2015-01-01

Abstract Objectives: to assess nurses' perceptions of risk factors for the development of phlebitis, with a special focus on the perception of phlebitic potentials of some infusion medications and solutions. Method: a cross-sectional questionnaire study, which included a sample of 102 nurses. Results: Nurses recognized some factors that may reduce the incidence of phlebitis; however, more than half of the nurses were unaware that the material and diameter of the cannula can affect the incidence rate of phlebitis. Furthermore,underlying disease and high pH of medications or solutions were identified as potential risk factors, whereas low pH and low osmolality were not. Nurses identified Vancomycin and Benzylpenicillin antibiotics with the strongest phlebitic potential. Among other medications and intravenous fluids, Aminophylline, Amiodaronehydrochloride and Potassium chloride 7.4% were identified as potentially causing phlebitis. Conclusion: predisposing factors for phlebitis relating to patients and administered therapy were identified by nurses, while some cannula related risk factors, in particular its physicochemical properties and the time for cannula replacement, were not fully perceived. PMID:26444170

Cutaneous exposure scenarios for engineered nanoparticles used in semiconductor fabrication: a preliminary investigation of workplace surface contamination

PubMed Central

Shepard, Michele; Brenner, Sara

2014-01-01

Background: Numerous studies are ongoing in the fields of nanotoxicology and exposure science; however, gaps remain in identifying and evaluating potential exposures from skin contact with engineered nanoparticles in occupational settings. Objectives: The aim of this study was to identify potential cutaneous exposure scenarios at a workplace using engineered nanoparticles (alumina, ceria, amorphous silica) and evaluate the presence of these materials on workplace surfaces. Methods: Process review, workplace observations, and preliminary surface sampling were conducted using microvacuum and wipe sample collection methods and transmission electron microscopy with elemental analysis. Results: Exposure scenarios were identified with potential for incidental contact. Nanoparticles of silica or silica and/or alumina agglomerates (or aggregates) were identified in surface samples from work areas where engineered nanoparticles were used or handled. Conclusions: Additional data are needed to evaluate occupational exposures from skin contact with engineered nanoparticles; precautionary measures should be used to minimize potential cutaneous exposures in the workplace. PMID:25000112

The effect of material choice on biofilm formation in a model warm water distribution system.

PubMed

Waines, Paul L; Moate, Roy; Moody, A John; Allen, Mike; Bradley, Graham

2011-11-01

Water distribution systems (WDS) are composed of a variety of materials and may harbour potential pathogens within surface-attached microbial biofilms. Biofilm formation on four plumbing materials, viz. copper, stainless steel 316 (SS316), ethylene propylene diene monomer (EPDM) and cross-linked polyethylene (PEX), was investigated using scanning electron microscope (SEM)/confocal microscopy, ATP-/culture-based analysis, and molecular analysis. Material 'inserts' were incorporated into a mains water fed, model WDS. All materials supported biofilm growth to various degrees. After 84 days, copper and SS316 showed no significant overall differences in terms of the level of biofilm formation observed, whilst PEX supported a significantly higher level of biofilm. EPDM exhibited gross contamination by a complex, multispecies biofilm, at a level significantly higher than was observed on the other materials, regardless of the analytical method used. PCR-DGGE analysis showed clear differences in the composition of the biofilm community on all materials after 84 days. The primary conclusion of this study has been to identify EPDM as a potentially unsuitable material for use as a major component in WDS.

Environmental effects on composite airframes: A study conducted for the ARM UAV Program (Atmospheric Radiation Measurement Unmanned Aerospace Vehicle)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Noguchi, R.A.

1994-06-01

Composite materials are affected by environments differently than conventional airframe structural materials are. This study identifies the environmental conditions which the composite-airframe ARM UAV may encounter, and discusses the potential degradation processes composite materials may undergo when subjected to those environments. This information is intended to be useful in a follow-on program to develop equipment and procedures to prevent, detect, or otherwise mitigate significant degradation with the ultimate goal of preventing catastrophic aircraft failure.

Oxygen Compatibility Testing of Composite Materials

NASA Technical Reports Server (NTRS)

Engel, Carl D.; Watkins, Casey N.

2006-01-01

Composite materials offer significant weight-saving potential for aerospace applications in propellant and oxidizer tanks. This application for oxygen tanks presents the challenge of being oxygen compatible in addition to complying with the other required material characteristics. This effort reports on the testing procedures and data obtained in examining and selecting potential composite materials for oxygen tank usage. Impact testing of composites has shown that most of these materials initiate a combustion event when impacted at 72 ft-lbf in the presence of liquid oxygen, though testing has also shown substantial variability in reaction sensitivities to impact. Data for screening of 14 potential composites using the Bruceton method is given herein and shows that the 50-percent reaction frequencies range from 17 to 67 ft-lbf. The pressure and temperature rises for several composite materials were recorded to compare the energy releases as functions of the combustion reactions with their respective reaction probabilities. The test data presented are primarily for a test pressure of 300 psia in liquid oxygen. The impact screening process is compared with oxygen index and autogenous ignition test data for both the composite and the basic resin. The usefulness of these supplemental tests in helping select the most oxygen compatible materials is explored. The propensity for mechanical impact ignition of the composite compared with the resin alone is also examined. Since an ignition-free composite material at the peak impact energy of 72 ft-lbf has not been identified, composite reactivity must be characterized over the impact energy level and operating pressure ranges to provide data for hazard analyses in selecting the best potential material for liquid tank usage.

Emergency material allocation with time-varying supply-demand based on dynamic optimization method for river chemical spills.

PubMed

Liu, Jie; Guo, Liang; Jiang, Jiping; Jiang, Dexun; Wang, Peng

2018-04-13

Aiming to minimize the damage caused by river chemical spills, efficient emergency material allocation is critical for an actual emergency rescue decision-making in a quick response. In this study, an emergency material allocation framework based on time-varying supply-demand constraint is developed to allocate emergency material, minimize the emergency response time, and satisfy the dynamic emergency material requirements in post-accident phases dealing with river chemical spills. In this study, the theoretically critical emergency response time is firstly obtained for the emergency material allocation system to select a series of appropriate emergency material warehouses as potential supportive centers. Then, an enumeration method is applied to identify the practically critical emergency response time, the optimum emergency material allocation and replenishment scheme. Finally, the developed framework is applied to a computational experiment based on south-to-north water transfer project in China. The results illustrate that the proposed methodology is a simple and flexible tool for appropriately allocating emergency material to satisfy time-dynamic demands during emergency decision-making. Therefore, the decision-makers can identify an appropriate emergency material allocation scheme in a balance between time-effective and cost-effective objectives under the different emergency pollution conditions.

Photovoltaic module encapsulation design and materials selection, volume 1

NASA Technical Reports Server (NTRS)

Cuddihy, E.; Carroll, W.; Coulbert, C.; Gupta, A.; Liang, R. H.

1982-01-01

Encapsulation material system requirements, material selection criteria, and the status and properties of encapsulation materials and processes available are presented. Technical and economic goals established for photovoltaic modules and encapsulation systems and their status are described. Available encapsulation technology and data are presented to facilitate design and material selection for silicon flat plate photovoltaic modules, using the best materials available and processes optimized for specific power applications and geographic sites. The operational and environmental loads that encapsulation system functional requirements and candidate design concepts and materials that are identified to have the best potential to meet the cost and performance goals for the flat plate solar array project are described. Available data on encapsulant material properties, fabrication processing, and module life and durability characteristics are presented.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grant, Ashleigh; Wilkinson, T.J.; Holman, Thomas

Analysis of fingerprints has predominantly focused on matching the pattern of ridges to a specific person as a form of identification. The present work focuses on identifying extrinsic materials that are left within a person's fingerprint after recent handling of such materials. Specifically, we employed infrared spectromicroscopy to locate and positively identify microscopic particles from a mixture of common materials in the latent human fingerprints of volunteer subjects. We were able to find and correctly identify all test substances based on their unique infrared spectral signatures. Spectral imaging is demonstrated as a method for automating recognition of specific substances inmore » a fingerprint. We also demonstrate the use of Attenuated Total Reflectance (ATR) and synchrotron-based infrared spectromicroscopy for obtaining high-quality spectra from particles that were too thick or too small, respectively, for reflection/absorption measurements. We believe the application of this rapid, non-destructive analytical technique to the forensic study of latent human finger prints has the potential to add a new layer of information available to investigators. Using fingerprints to not only identify who was present at a crime scene, but also to link who was handling key materials will be a powerful investigative tool.« less

Exposure assessment and risk management of engineered nanoparticles: Investigation in semiconductor wafer processing

NASA Astrophysics Data System (ADS)

Shepard, Michele N.

Engineered nanomaterials (ENMs) are currently used in hundreds of commercial products and industrial processes, with more applications being investigated. Nanomaterials have unique properties that differ from bulk materials. While these properties may enable technological advancements, the potential risks of ENMs to people and the environment are not yet fully understood. Certain low solubility nanoparticles are more toxic than their bulk material, such that existing occupational exposure limits may not be sufficiently protective for workers. Risk assessments are currently challenging due to gaps in data on the numerous emerging materials and applications as well as method uncertainties and limitations. Chemical mechanical planarization (CMP) processes with engineered nanoparticle abrasives are used for research and commercial manufacturing applications in the semiconductor and related industries. Despite growing use, no published studies addressed occupational exposures to nanoparticles associated with CMP or risk assessment and management practices for these scenarios. Additional studies are needed to evaluate potential sources of workplace exposure or emission, as well as to help test and refine assessment methods. This research was conducted to: identify the lifecycle stages and potential exposure sources for ENMs in CMP processes; characterize worker exposure; determine recommended engineering controls and compare risk assessment models. The study included workplace air and surface sampling and an evaluation of qualitative risk banding approaches. Exposure assessment results indicated the potential for worker contact with ENMs on workplace surfaces but did not identify nanoparticles readily dispersed in air during work tasks. Some increases in respirable particle concentrations were identified, but not consistently. Measured aerosol concentrations by number and mass were well below current reference values for poorly soluble low toxicity nanoparticles. From application and evaluation of qualitative risk assessment approaches, differences in control banding models and results were identified, although output generally agreed with conclusions from air sampling as to whether an upgrade in site engineering controls was recommended. This research helped to improve understanding of potential worker exposures to ENMs in CMP processes, as well as the methods for risk assessment and management of metal oxide nanoparticles in occupational environments.

The reactivity of sodium alanates with O[2], H[2]O, and CO[2] : an investigation of complex metal hydride contamination in the context of automotive systems.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dedrick, Daniel E.; Bradshaw, Robert W.; Behrens, Richard, Jr.

2007-08-01

Safe and efficient hydrogen storage is a significant challenge inhibiting the use of hydrogen as a primary energy carrier. Although energy storage performance properties are critical to the success of solid-state hydrogen storage systems, operator and user safety is of highest importance when designing and implementing consumer products. As researchers are now integrating high energy density solid materials into hydrogen storage systems, quantification of the hazards associated with the operation and handling of these materials becomes imperative. The experimental effort presented in this paper focuses on identifying the hazards associated with producing, storing, and handling sodium alanates, and thus allowingmore » for the development and implementation of hazard mitigation procedures. The chemical changes of sodium alanates associated with exposure to oxygen and water vapor have been characterized by thermal decomposition analysis using simultaneous thermogravimetric modulated beam mass spectrometry (STMBMS) and X-ray diffraction methods. Partial oxidation of sodium alanates, an alkali metal complex hydride, results in destabilization of the remaining hydrogen-containing material. At temperatures below 70 C, reaction of sodium alanate with water generates potentially combustible mixtures of H{sub 2} and O{sub 2}. In addition to identifying the reaction hazards associated with the oxidation of alkali-metal containing complex hydrides, potential treatment methods are identified that chemically stabilize the oxidized material and reduce the hazard associated with handling the contaminated metal hydrides.« less

Potential High-Temperature Shape-Memory Alloys Identified in the Ti(Ni,Pt) System

NASA Technical Reports Server (NTRS)

Noebe, Ronald D.; Biles, Tiffany A.; Garg, Anita; Nathal, Michael V.

2004-01-01

"Shape memory" is a unique property of certain alloys that, when deformed (within certain strain limits) at low temperatures, will remember and recover to their original predeformed shape upon heating. It occurs when an alloy is deformed in the low-temperature martensitic phase and is then heated above its transformation temperature back to an austenitic state. As the material passes through this solid-state phase transformation on heating, it also recovers its original shape. This behavior is widely exploited, near room temperature, in commercially available NiTi alloys for connectors, couplings, valves, actuators, stents, and other medical and dental devices. In addition, there are limitless applications in the aerospace, automotive, chemical processing, and many other industries for materials that exhibit this type of shape-memory behavior at higher temperatures. But for high temperatures, there are currently no commercial shape-memory alloys. Although there are significant challenges to the development of high-temperature shape-memory alloys, at the NASA Glenn Research Center we have identified a series of alloy compositions in the Ti-Ni-Pt system that show great promise as potential high-temperature shape-memory materials.

Installation-Restoration Program Preliminary Assessment, Naknek Recreational Camps, Alaska

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1989-04-01

The Hazardous Materials Technical Center (HMTC) was retained in January 1988 to conduct the Installation-Restoration Program (IRP) Preliminary Assessment of Naknek Recreational Camps, Alaska, DoD policy is to identify and fully evaluate suspected problems associated with past hazardous-material disposal sites on DoD facilities, control the migration of hazardous contamination from such facilities, and control hazards to health and welfare that may have resulted from these past operations. Past installation operations involved the use and disposal of materials and wastes that were subsequently categorized as hazardous. The major operations of Naknek Camp I and Camp II did not use or disposemore » of HM/HW; however, these camps were used by the Air Force as dump areas and landfills. Waste oils, fuels, and polychlorinated biphenyls (PCBs) were among the wastes disposed of during these dumping activities. Information obtained through interviews, records, and field observations resulted in the identification of three sites that are potentially contaminated with HM/HW. At each of the identified sites, the potential exists for contamination of surface water, soils, and/or ground water and subsequent contaminant migration.« less

Selection and authentication of botanical materials for the development of analytical methods.

PubMed

Applequist, Wendy L; Miller, James S

2013-05-01

Herbal products, for example botanical dietary supplements, are widely used. Analytical methods are needed to ensure that botanical ingredients used in commercial products are correctly identified and that research materials are of adequate quality and are sufficiently characterized to enable research to be interpreted and replicated. Adulteration of botanical material in commerce is common for some species. The development of analytical methods for specific botanicals, and accurate reporting of research results, depend critically on correct identification of test materials. Conscious efforts must therefore be made to ensure that the botanical identity of test materials is rigorously confirmed and documented through preservation of vouchers, and that their geographic origin and handling are appropriate. Use of material with an associated herbarium voucher that can be botanically identified is always ideal. Indirect methods of authenticating bulk material in commerce, for example use of organoleptic, anatomical, chemical, or molecular characteristics, are not always acceptable for the chemist's purposes. Familiarity with botanical and pharmacognostic literature is necessary to determine what potential adulterants exist and how they may be distinguished.

Light Duty Truck Weight Reduction Evaluation

DOT National Transportation Integrated Search

1980-10-01

The objectives of this program were to identify the weight reduction potential of pickup trucks, vans, and utility vehicles less than or equal to 8500 lb. gross vehicle weight through design modification, redesign, and material substitution; and more...

Design of lateral heterostructure from arsenene and antimonene

NASA Astrophysics Data System (ADS)

Sun, Qilong; Dai, Ying; Ma, Yandong; Yin, Na; Wei, Wei; Yu, Lin; Huang, Baibiao

2016-09-01

Lateral heterostructures fabricated by two-dimensional building blocks have opened up exciting realms in material science and device physics. Identifying suitable materials for creating such heterostructures is urgently needed for the next-generation devices. Here, we demonstrate a novel type of seamless lateral heterostructures with excellent stabilities formed within pristine arsenene and antimonene. We find that these heterostructures could possess direct and reduced energy gaps without any modulations. Moreover, the highly coveted type-II alignment and the high carrier mobility are also identified, marking the enhanced quantum efficiency. The tensile strain can result in efficient bandgap engineering. Besides, the proposed critical condition for favored direct energy gaps would have a guiding significance on the subsequent works. Generally, our predictions not only introduce new vitality into lateral heterostructures, enriching available candidate materials in this field, but also highlight the potential of these lateral heterostructures as appealing materials for future devices.

Defect Genome of Cubic Perovskites for Fuel Cell Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Balachandran, Janakiraman; Lin, Lianshan; Anchell, Jonathan S.

Heterogeneities such as point defects, inherent to material systems, can profoundly influence material functionalities critical for numerous energy applications. This influence in principle can be identified and quantified through development of large defect data sets which we call the defect genome, employing high-throughput ab initio calculations. However, high-throughput screening of material models with point defects dramatically increases the computational complexity and chemical search space, creating major impediments toward developing a defect genome. In this paper, we overcome these impediments by employing computationally tractable ab initio models driven by highly scalable workflows, to study formation and interaction of various point defectsmore » (e.g., O vacancies, H interstitials, and Y substitutional dopant), in over 80 cubic perovskites, for potential proton-conducting ceramic fuel cell (PCFC) applications. The resulting defect data sets identify several promising perovskite compounds that can exhibit high proton conductivity. Furthermore, the data sets also enable us to identify and explain, insightful and novel correlations among defect energies, material identities, and defect-induced local structural distortions. Finally, such defect data sets and resultant correlations are necessary to build statistical machine learning models, which are required to accelerate discovery of new materials.« less

Defect Genome of Cubic Perovskites for Fuel Cell Applications

DOE PAGES

Balachandran, Janakiraman; Lin, Lianshan; Anchell, Jonathan S.; ...

2017-10-10

Heterogeneities such as point defects, inherent to material systems, can profoundly influence material functionalities critical for numerous energy applications. This influence in principle can be identified and quantified through development of large defect data sets which we call the defect genome, employing high-throughput ab initio calculations. However, high-throughput screening of material models with point defects dramatically increases the computational complexity and chemical search space, creating major impediments toward developing a defect genome. In this paper, we overcome these impediments by employing computationally tractable ab initio models driven by highly scalable workflows, to study formation and interaction of various point defectsmore » (e.g., O vacancies, H interstitials, and Y substitutional dopant), in over 80 cubic perovskites, for potential proton-conducting ceramic fuel cell (PCFC) applications. The resulting defect data sets identify several promising perovskite compounds that can exhibit high proton conductivity. Furthermore, the data sets also enable us to identify and explain, insightful and novel correlations among defect energies, material identities, and defect-induced local structural distortions. Finally, such defect data sets and resultant correlations are necessary to build statistical machine learning models, which are required to accelerate discovery of new materials.« less

Biomimetic-inspired joining of composite with metal structures: A survey of natural joints and application to single lap joints

NASA Astrophysics Data System (ADS)

Avgoulas, Evangelos Ioannis; Sutcliffe, Michael P. F.

2014-03-01

Joining composites with metal parts leads, inevitably, to high stress concentrations because of the material property mismatch. Since joining composite to metal is required in many high performance structures, there is a need to develop a new multifunctional approach to meet this challenge. This paper uses the biomimetics approach to help develop solutions to this problem. Nature has found many ingenious ways of joining dissimilar materials and making robust attachments, alleviating potential stress concentrations. A literature survey of natural joint systems has been carried out, identifying and analysing different natural joint methods from a mechanical perspective. A taxonomy table was developed based on the different methods/functions that nature successfully uses to attach dissimilar tissues (materials). This table is used to understand common themes or approaches used in nature for different joint configurations and functionalities. One of the key characteristics that nature uses to joint dissimilar materials is a transitional zone of stiffness in the insertion site. Several biomimetic-inspired metal-to-composite (steel-to-CFRP), adhesively bonded, Single Lap Joints (SLJs) were numerically investigated using a finite element analysis. The proposed solutions offer a transitional zone of stiffness of one joint part to reduce the material stiffness mismatch at the joint. An optimisation procedure was used to identify the variation in material stiffness which minimises potential failure of the joint. It was found that the proposed biomimetic SLJs reduce the asymmetry of the stress distribution along the adhesive area.

Eutectic Composite Turbine Blade Development

DTIC Science & Technology

1976-11-01

turbine blades for aircraft engines . An MC carbide fiber reinforced eutectic alloy, NiTaC-13...composites in turbine blades for aircraft engines . An MC carbide fiber reinforced eutectic alloy, NiTaC-13 and the low pressure turbine blade of the...identified that appeared to have potential for application to aircraft engine turbine blade hardware. The potential benefits offered by these materials

Industrial waste materials and by-products as thermal energy storage (TES) materials: A review

NASA Astrophysics Data System (ADS)

Gutierrez, Andrea; Miró, Laia; Gil, Antoni; Rodríguez-Aseguinolaza, Javier; Barreneche, Camila; Calvet, Nicolas; Py, Xavier; Fernández, A. Inés; Grágeda, Mario; Ushak, Svetlana; Cabeza, Luisa F.

2016-05-01

A wide variety of potential materials for thermal energy storage (TES) have been identify depending on the implemented TES method, Sensible, latent or thermochemical. In order to improve the efficiency of TES systems more alternatives are continuously being sought. In this regard, this paper presents the review of low cost heat storage materials focused mainly in two objectives: on the one hand, the implementation of improved heat storage devices based on new appropriate materials and, on the other hand, the valorisation of waste industrial materials will have strong environmental, economic and societal benefits such as reducing the landfilled waste amounts, reducing the greenhouse emissions and others. Different industrial and municipal waste materials and by products have been considered as potential TES materials and have been characterized as such. Asbestos containing wastes, fly ashes, by-products from the salt industry and from the metal industry, wastes from recycling steel process and from copper refining process and dross from the aluminium industry, and municipal wastes (glass and nylon) have been considered. This work shows a great revalorization of wastes and by-product opportunity as TES materials, although more studies are needed to achieve industrial deployment of the idea.

Materials Analysis and Modeling of Underfill Materials.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wyatt, Nicholas B; Chambers, Robert S.

2015-08-01

The thermal-mechanical properties of three potential underfill candidate materials for PBGA applications are characterized and reported. Two of the materials are a formulations developed at Sandia for underfill applications while the third is a commercial product that utilizes a snap-cure chemistry to drastically reduce cure time. Viscoelastic models were calibrated and fit using the property data collected for one of the Sandia formulated materials. Along with the thermal-mechanical analyses performed, a series of simple bi-material strip tests were conducted to comparatively analyze the relative effects of cure and thermal shrinkage amongst the materials under consideration. Finally, current knowledge gaps asmore » well as questions arising from the present study are identified and a path forward presented.« less

Qualification and initial characterization of a high-purity 233U spike for use in uranium analyses

DOE PAGES

Mathew, K. J.; Canaan, R. D.; Hexel, C.; ...

2015-08-20

Several high-purity 233U items potentially useful as isotope dilution mass spectrometry standards for safeguards, non-proliferation, and nuclear forensics measurements are identified and rescued from downblending. By preserving the supply of 233U materials of different pedigree for use as source materials for certified reference materials (CRMs), it is ensured that the safeguards community has high quality uranium isotopic standards required for calibration of the analytical instruments. One of the items identified as a source material for a high-purity CRM is characterized for the uranium isotope-amount ratios using thermal ionization mass spectrometry (TIMS). Additional verification measurements on this material using quadrupole inductivelymore » coupled plasma mass spectrometry (ICPMS) are also performed. As a result, the comparison of the ICPMS uranium isotope-amount ratios with the TIMS data, with much smaller uncertainties, validated the ICPMS measurement practices. ICPMS is proposed for the initial screening of the purity of items in the rescue campaign.« less

p × n-Type Transverse Thermoelectrics: A Novel Type of Thermal Management Material

NASA Astrophysics Data System (ADS)

Tang, Yang; Cui, Boya; Zhou, Chuanle; Grayson, Matthew

2015-06-01

In this paper we review the recently identified p × n-type transverse thermoelectrics and study the thermoelectric properties of the proposed candidate materials. Anisotropic electron and hole conductivity arise from either an artificially engineered band structure or from appropriately anisotropic crystals, and result in orthogonal p-type and n-type directional Seebeck coefficients, inducing a non-zero off-diagonal transverse Seebeck coefficient with appropriately oriented currents. Such materials have potential for new applications of thermoelectric materials in transverse Peltier cooling and transverse thermal energy harvesting. In this paper we review general transverse thermoelectric phenomena to identify advantages of p × n-type transverse thermoelectrics compared with previously studied transverse thermoelectric phenomena. An intuitive overview of the band structure of one such p × n-material, the InAs/GaSb type-II superlattice, is introduced, and the plot of thermoelectric performance as a function of superlattice structure is calculated, as an example of how band structures can be optimized for the best transverse thermoelectric performance.

Two-dimensional materials from high-throughput computational exfoliation of experimentally known compounds.

PubMed

Mounet, Nicolas; Gibertini, Marco; Schwaller, Philippe; Campi, Davide; Merkys, Andrius; Marrazzo, Antimo; Sohier, Thibault; Castelli, Ivano Eligio; Cepellotti, Andrea; Pizzi, Giovanni; Marzari, Nicola

2018-03-01

Two-dimensional (2D) materials have emerged as promising candidates for next-generation electronic and optoelectronic applications. Yet, only a few dozen 2D materials have been successfully synthesized or exfoliated. Here, we search for 2D materials that can be easily exfoliated from their parent compounds. Starting from 108,423 unique, experimentally known 3D compounds, we identify a subset of 5,619 compounds that appear layered according to robust geometric and bonding criteria. High-throughput calculations using van der Waals density functional theory, validated against experimental structural data and calculated random phase approximation binding energies, further allowed the identification of 1,825 compounds that are either easily or potentially exfoliable. In particular, the subset of 1,036 easily exfoliable cases provides novel structural prototypes and simple ternary compounds as well as a large portfolio of materials to search from for optimal properties. For a subset of 258 compounds, we explore vibrational, electronic, magnetic and topological properties, identifying 56 ferromagnetic and antiferromagnetic systems, including half-metals and half-semiconductors.

Learning to perceive haptic distance-to-break in the presence of friction.

PubMed

Altenhoff, Bliss M; Pagano, Christopher C; Kil, Irfan; Burg, Timothy C

2017-02-01

Two experiments employed attunement and calibration training to investigate whether observers are able to identify material break points in compliant materials through haptic force application. The task required participants to attune to a recently identified haptic invariant, distance-to-break (DTB), rather than haptic stimulation not related to the invariant, including friction. In the first experiment participants probed simulated force-displacement relationships (materials) under 3 levels of friction with the aim of pushing as far as possible into the materials without breaking them. In a second experiment a different set of participants pulled on the materials. Results revealed that participants are sensitive to DTB for both pushing and pulling, even in the presence of varying levels of friction, and this sensitivity can be improved through training. The results suggest that the simultaneous presence of friction may assist participants in perceiving DTB. Potential applications include the development of haptic training programs for minimally invasive (laparoscopic) surgery to reduce accidental tissue damage. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Two-dimensional materials from high-throughput computational exfoliation of experimentally known compounds

NASA Astrophysics Data System (ADS)

Mounet, Nicolas; Gibertini, Marco; Schwaller, Philippe; Campi, Davide; Merkys, Andrius; Marrazzo, Antimo; Sohier, Thibault; Castelli, Ivano Eligio; Cepellotti, Andrea; Pizzi, Giovanni; Marzari, Nicola

2018-02-01

Two-dimensional (2D) materials have emerged as promising candidates for next-generation electronic and optoelectronic applications. Yet, only a few dozen 2D materials have been successfully synthesized or exfoliated. Here, we search for 2D materials that can be easily exfoliated from their parent compounds. Starting from 108,423 unique, experimentally known 3D compounds, we identify a subset of 5,619 compounds that appear layered according to robust geometric and bonding criteria. High-throughput calculations using van der Waals density functional theory, validated against experimental structural data and calculated random phase approximation binding energies, further allowed the identification of 1,825 compounds that are either easily or potentially exfoliable. In particular, the subset of 1,036 easily exfoliable cases provides novel structural prototypes and simple ternary compounds as well as a large portfolio of materials to search from for optimal properties. For a subset of 258 compounds, we explore vibrational, electronic, magnetic and topological properties, identifying 56 ferromagnetic and antiferromagnetic systems, including half-metals and half-semiconductors.

Polymer microarray technology for stem cell engineering

PubMed Central

Coyle, Robert; Jia, Jia; Mei, Ying

2015-01-01

Stem cells hold remarkable promise for applications in tissue engineering and disease modeling. During the past decade, significant progress has been made in developing soluble factors (e.g., small molecules and growth factors) to direct stem cells into a desired phenotype. However, the current lack of suitable synthetic materials to regulate stem cell activity has limited the realization of the enormous potential of stem cells. This can be attributed to a large number of materials properties (e.g., chemical structures and physical properties of materials) that can affect stem cell fate. This makes it challenging to design biomaterials to direct stem cell behavior. To address this, polymer microarray technology has been developed to rapidly identify materials for a variety of stem cell applications. In this article, we summarize recent developments in polymer array technology and their applications in stem cell engineering. Statement of significance Stem cells hold remarkable promise for applications in tissue engineering and disease modeling. In the last decade, significant progress has been made in developing chemically defined media to direct stem cells into a desired phenotype. However, the current lack of the suitable synthetic materials to regulate stem cell activities has been limiting the realization of the potential of stem cells. This can be attributed to the number of variables in material properties (e.g., chemical structures and physical properties) that can affect stem cells. Polymer microarray technology has shown to be a powerful tool to rapidly identify materials for a variety of stem cell applications. Here we summarize recent developments in polymer array technology and their applications in stem cell engineering. PMID:26497624

Comparing results of X-ray diffraction, µ-Raman spectroscopy and neutron diffraction when identifying chemical phases in seized nuclear material, during a comparative nuclear forensics exercise.

PubMed

Rondahl, Stina Holmgren; Pointurier, Fabien; Ahlinder, Linnea; Ramebäck, Henrik; Marie, Olivier; Ravat, Brice; Delaunay, François; Young, Emma; Blagojevic, Ned; Hester, James R; Thorogood, Gordon; Nelwamondo, Aubrey N; Ntsoane, Tshepo P; Roberts, Sarah K; Holliday, Kiel S

2018-01-01

This work presents the results for identification of chemical phases obtained by several laboratories as a part of an international nuclear forensic round-robin exercise. In this work powder X-ray diffraction (p-XRD) is regarded as the reference technique. Neutron diffraction produced a superior high-angle diffraction pattern relative to p-XRD. Requiring only small amounts of sample, µ-Raman spectroscopy was used for the first time in this context as a potentially complementary technique to p-XRD. The chemical phases were identified as pure UO 2 in two materials, and as a mixture of UO 2 , U 3 O 8 and an intermediate species U 3 O 7 in the third material.

A HUMAN RELIABILITY-CENTERED APPROACH TO THE DEVELOPMENT OF JOB AIDS FOR REVIEWERS OF MEDICAL DEVICES THAT USE RADIOLOGICAL BYPRODUCT MATERIALS.

DOE Office of Scientific and Technical Information (OSTI.GOV)

COOPER, S.E.; BROWN, W.S.; WREATHALL, J.

2005-02-02

The U.S. Nuclear Regulatory Commission (NRC) is engaged in an initiative to risk-inform the regulation of byproduct materials. Operating experience indicates that human actions play a dominant role in most of the activities involving byproduct materials, which are radioactive materials other than those used in nuclear power plants or in weapons production, primarily for medical or industrial purposes. The overall risk of these activities is strongly influenced by human performance. Hence, an improved understanding of human error, its causes and contexts, and human reliability analysis (HRA) is important in risk-informing the regulation of these activities. The development of the humanmore » performance job aids was undertaken by stages, with frequent interaction with the prospective users. First, potentially risk significant human actions were identified based on reviews of available risk studies for byproduct material applications and of descriptions of events for byproduct materials applications that involved potentially significant human actions. Applications from the medical and the industrial domains were sampled. Next, the specific needs of the expected users of the human performance-related capabilities were determined. To do this, NRC headquarters and region staff were interviewed to identify the types of activities (e.g., license reviews, inspections, event assessments) that need HRA support and the form in which such support might best be offered. Because the range of byproduct uses regulated by NRC is so broad, it was decided that initial development of knowledge and tools would be undertaken in the context of a specific use of byproduct material, which was selected in consultation with NRC staff. Based on needs of NRC staff and the human performance related characteristics of the context chosen, knowledge resources were then compiled to support consideration of human performance issues related to the regulation of byproduct materials. Finally, with information sources and an application context identified, a set of strawman job aids was developed, which was then presented to prospective users for critique and comment. Work is currently under way to develop training materials and refine the job aids in preparation for a pilot evaluation.« less

Modeling workflow to design machine translation applications for public health practice

PubMed Central

Turner, Anne M.; Brownstein, Megumu K.; Cole, Kate; Karasz, Hilary; Kirchhoff, Katrin

2014-01-01

Objective Provide a detailed understanding of the information workflow processes related to translating health promotion materials for limited English proficiency individuals in order to inform the design of context-driven machine translation (MT) tools for public health (PH). Materials and Methods We applied a cognitive work analysis framework to investigate the translation information workflow processes of two large health departments in Washington State. Researchers conducted interviews, performed a task analysis, and validated results with PH professionals to model translation workflow and identify functional requirements for a translation system for PH. Results The study resulted in a detailed description of work related to translation of PH materials, an information workflow diagram, and a description of attitudes towards MT technology. We identified a number of themes that hold design implications for incorporating MT in PH translation practice. A PH translation tool prototype was designed based on these findings. Discussion This study underscores the importance of understanding the work context and information workflow for which systems will be designed. Based on themes and translation information workflow processes, we identified key design guidelines for incorporating MT into PH translation work. Primary amongst these is that MT should be followed by human review for translations to be of high quality and for the technology to be adopted into practice. Counclusion The time and costs of creating multilingual health promotion materials are barriers to translation. PH personnel were interested in MT's potential to improve access to low-cost translated PH materials, but expressed concerns about ensuring quality. We outline design considerations and a potential machine translation tool to best fit MT systems into PH practice. PMID:25445922

Removing Hazardous Materials from Buildings: A Training Curriculum

DTIC Science & Technology

2016-03-01

Army Pamphlet DAIM-ODF OACSIM Facility Policy Division DHHS Department of Health and Human Services DoD Department of Defense DoDD Department of...materials have the potential to: – Damage human health and safety – Damage environmental systems through releases to the air, water, or soil • Certain...EPA, or otherwise identified as creating an environmental and/or human health hazard when deteriorated or disturbed, or when entering the waste

Phase Change Material Trade Study: A Comparison Between Wax and Water for Manned Spacecraft

NASA Technical Reports Server (NTRS)

Quinn, Gregory; Hodgson, Ed; Stephan, Ryan A,

2011-01-01

Phase change material heat sinks have been recognized as an important tool in optimizing thermal control systems for space exploration vehicles and habitats that must deal with widely varying thermal loads and environments. In order to better focus technology investment in this arena, NASA has supported a trade study with the objective of identifying where the best potential pay-off can be found among identified aqueous and paraffin wax phase change materials and phase change material heat sink design approaches. The study used a representative exploration mission with well understood parameters to support the trade. Additional sensitivity studies were performed to ensure the applicability of study results across varying systems and destinations. Results from the study indicate that replacing a wax PCM heat sink with a water ice PCM heat sink has the potential to decrease the equivalent system mass of the mission s vehicle through a combination of a smaller heat sink and a slight 5% increase in radiator size or the addition of a lightweight heat pump. An evaluation of existing and emerging PCM heat sink technologies indicates that further mass savings should be achievable through continued development of those technologies. The largest mass savings may be realized by eliminating the melting and freezing pressure of wax and water, respectively.

Topologic connection between 2-D layered structures and 3-D diamond structures for conventional semiconductors

PubMed Central

Wang, Jianwei; Zhang, Yong

2016-01-01

When coming to identify new 2D materials, our intuition would suggest us to look from layered instead of 3D materials. However, since graphite can be hypothetically derived from diamond by stretching it along its [111] axis, many 3D materials can also potentially be explored as new candidates for 2D materials. Using a density functional theory, we perform a systematic study over the common Group IV, III–V, and II–VI semiconductors along different deformation paths to reveal new structures that are topologically connected to but distinctly different from the 3D parent structure. Specifically, we explore two major phase transition paths, originating respectively from wurtzite and NiAs structure, by applying compressive and tensile strain along the symmetry axis, and calculating the total energy changes to search for potential metastable states, as well as phonon spectra to examine the structural stability. Each path is found to further split into two branches under tensile strain–low buckled and high buckled structures, which respectively lead to a low and high buckled monolayer structure. Most promising new layered or planar structures identified include BeO, GaN, and ZnO on the tensile strain side, Ge, Si, and GaP on the compressive strain side. PMID:27090430

Identification of intentionally and non-intentionally added substances in plastic packaging materials and their migration into food products.

PubMed

García Ibarra, Verónica; Rodríguez Bernaldo de Quirós, Ana; Paseiro Losada, Perfecto; Sendón, Raquel

2018-05-07

Plastic materials are widely used in food packaging applications; however, there is increased concern because of the possible release of undesirable components into foodstuffs. Migration of plastic constituents not only has the potential to affect product quality but also constitutes a risk to consumer health. In order to check the safety of food contact materials, analytical methodologies to identify potential migrants are required. In the first part of this work, a GC/MS screening method was developed for the identification of components from plastic packaging materials including intentionally and "non-intentionally added substances" (NIAS) as potential migrants. In the second part of this study, the presence of seven compounds (bis (2-ethylhexyl) phthalate (DEHP), diethyl phthalate (DEP), diisobutyl phthalate (DIBP), dibutyl phthalate (DBP), butylated hydroxytoluene (BHT), acetyl tributyl citrate (ATBC), benzophenone (BP)) previously identified in packaging materials were investigated in food products (corn and potatoes snacks, cookies, and cakes). For this purpose, a suitable extraction method was developed and quantification was performed using GC-MS. The developed method was validated in terms of linearity, recovery, repeatability, and limits of detection and quantification. The spiked recoveries varied between 82.7 and 116.1%, and relative standard deviation (RSD) was in the range of 2.22-15.9%. The plasticizer ATBC was the most detected compound (94% samples), followed by DEP (65%), DEHP (47%), BP (44%), DBP (35%), DIBP (21%), and BHT (12%). Regarding phthalates, DEP and DEHP were the most frequently detected compounds in concentrations up to 1.44 μg g -1 . In some samples, only DBP exceeded the European SML of 0.3 mg kg -1 established in Regulation 10/2011. Graphical abstract Chemical migration from plastic packaging into food.

Promoting medical tourism to India: messages, images, and the marketing of international patient travel.

PubMed

Crooks, Valorie A; Turner, Leigh; Snyder, Jeremy; Johnston, Rory; Kingsbury, Paul

2011-03-01

The practice of medical tourism depends on successfully informing potential patients about procedure options, treatment facilities, tourism opportunities, travel arrangements, and destination countries. The promotion of medical tourism includes a wide range of marketing materials such as flyers, booklets, and websites. Yet, there is a paucity of knowledge about the dissemination, content, and reception of these promotional materials. Drawing on a thematic content analysis of the promotional print material distributed at the first medical tourism trade show in Canada in 2009, the main purpose of this article is to identify and understand the messages and images that companies use to market India as a global destination. While researchers and news media frequently cite low cost procedures as a key determinant for international patient travel, particularly to developing nations, our analysis reveals few low cost-related images or messages in the promotional materials distributed at the trade show. To help explain this surprising disjuncture, we consider four related issues: (1) promotional materials may be designed to be circulated amongst potential patients' concerned family and friends who privilege knowing about things such as the use of advanced technologies; (2) developing nations need to portray safe and advanced treatment facilities in order to dispel potential patients' suspicions that their medical care is inferior; (3) companies may avoid making cost saving claims that cannot be fulfilled for all of their international patients, especially those traveling from developing nations; and (4) messages of low cost may detract from and even undermine messages about quality. We conclude by identifying numerous avenues for future research by social and health scientists, and by considering the implications of our findings for existing knowledge gaps and debates within health geography specifically. Copyright © 2011 Elsevier Ltd. All rights reserved.

Optimization of Regenerators for AMRR Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nellis, Gregory; Klein, Sanford; Brey, William

Active Magnetic Regenerative Refrigeration (AMRR) systems have no direct global warming potential or ozone depletion potential and hold the potential for providing refrigeration with efficiencies that are equal to or greater than the vapor compression systems used today. The work carried out in this project has developed and improved modeling tools that can be used to optimize and evaluate the magnetocaloric materials and geometric structure of the regenerator beds required for AMRR Systems. There has been an explosion in the development of magnetocaloric materials for AMRR systems over the past few decades. The most attractive materials, based on the magnitudemore » of the measured magnetocaloric effect, tend to also have large amounts of hysteresis. This project has provided for the first time a thermodynamically consistent method for evaluating these hysteretic materials in the context of an AMRR cycle. An additional, practical challenge that has been identified for AMRR systems is related to the participation of the regenerator wall in the cyclic process. The impact of housing heat capacity on both passive and active regenerative systems has been studied and clarified within this project. This report is divided into two parts corresponding to these two efforts. Part 1 describes the work related to modeling magnetic hysteresis while Part 2 discusses the modeling of the heat capacity of the housing. A key outcome of this project is the development of a publically available modeling tool that allows researchers to identify a truly optimal magnetocaloric refrigerant. Typically, the refrigeration potential of a magnetocaloric material is judged entirely based on the magnitude of the magnetocaloric effect and other properties of the material that are deemed unimportant. This project has shown that a material with a large magnetocaloric effect (as evidenced, for example, by a large adiabatic temperature change) may not be optimal when it is accompanied by a large hysteresis. The trade-off between these various material properties and the proper design of an AMRR system can only be evaluated correctly using the comprehensive, physics-based model developed by this project. The development of these modeling tools and optimization studies will provide the knowledge base that is required to achieve transformational discoveries. The widespread adoption of AMRR technology will change the character of energy demand in this country and provide manufacturing jobs as well as employment associated with retrofitting existing HVAC&R applications.« less

Arrow-wing supersonic cruise aircraft structural design concepts evaluation. Volume 2: Sections 7 through 11

NASA Technical Reports Server (NTRS)

Sakata, I. F.; Davis, G. W.

1975-01-01

The materials and advanced producibility methods that offer potential structural mass savings in the design of the primary structure for a supersonic cruise aircraft are identified and reported. A summary of the materials and fabrication techniques selected for this analytical effort is presented. Both metallic and composite material systems were selected for application to a near-term start-of-design technology aircraft. Selective reinforcement of the basic metallic structure was considered as the appropriate level of composite application for the near-term design.

Materials for Photovoltaic Applications

NASA Astrophysics Data System (ADS)

Dimova-Malinovska, Doriana

Energy priorities are changing nowadays. As mankind will probably have to face energy crisis, factors such as energy independence, energy security, stability of energy supply and the variety of energy sources become much more vital these days. Photovoltaics is exceptional compared to other renewable sources of energy due to its wide opportunity to gain energetic and environmental benefits. An overview of the present state of knowledge of the materials aspects of photovoltaic cells will be given, and new semiconductor materials, including nanomaterials, with potential for application in photovoltaic devices will be identified.

Space Station - The base for tomorrow's electronic industry

NASA Technical Reports Server (NTRS)

Naumann, Robert J.

1985-01-01

The potential value of space material processing on the Space Station for the electronics industry is examined. The primary advantages of the space environment for producing high-purity semiconductors and electrooptical materials are identified as the virtual absence of gravity (suppressing buoyancy-driven convection in melts and density segregation of alloys) and the availabilty of high vacuum (with high pumping speed and heat rejection). The recent history of material development and processing technology in the electronics industry is reviewed, and the principal features of early space experiments are outlined.

He implantation induced microstructure- and hardness-modification of the intermetallic γ-TiAl

NASA Astrophysics Data System (ADS)

Pouchon, Manuel A.; Chen, Jiachao; Hoffelner, Wolfgang

2009-05-01

TiAl is a well known high temperature material with good creep properties. It is investigated as a potential structural material for Generation IV high temperature gas cooled nuclear reactors. The tests are performed with the ABB-2 (Ti-rich TiAl with 2 at.% W) developed by ASEA Brown Boveri Ltd. (ABB). Thin samples are irradiated throughout with 24 MeV 4He2+ ions; the irradiated material is then investigated towards its microstructure and its hardness. The microstructure is studied by transmission electron microscopy and the hardness is investigated using a micro-hardness tester and a nano-indenter. Different effects can be identified. From room to moderate irradiation temperatures, the radiation induced hardening of the material slowly vanishes until the material completely recovers at about 943 K. Beyond this temperature, He-bubble formation seems to harden the material again, until beyond 1200 K a steep increase in hardening is detected. This effect can be correlated with bubbles being identified in the micrographs. The results are consistent and give strong indications to a microstructural development as a function of temperature.

TECHNICAL REPORT ON TECHNOLOGICALLY ENHANCED NATURALLY OCCURRING RADIOACTIVE MATERIALS FROM URANIUM MINING, VOLUME II: INVESTIGATION OF POTENTIAL HEALTH, GEOGRAPHIC, AND ENVIRONMENTAL ISSUES OF ABANDONED URANIUM MINES

EPA Science Inventory

Volume II investigates the potential radiogenic risks from abandoned uranium mines and evaluates which may pose the greatest hazards to members of the public and to the environment. The intent of this report is to identify who may be most likely to be exposed to wastes at small a...

Accelerating the design of solar thermal fuel materials through high throughput simulations.

PubMed

Liu, Yun; Grossman, Jeffrey C

2014-12-10

Solar thermal fuels (STF) store the energy of sunlight, which can then be released later in the form of heat, offering an emission-free and renewable solution for both solar energy conversion and storage. However, this approach is currently limited by the lack of low-cost materials with high energy density and high stability. In this Letter, we present an ab initio high-throughput computational approach to accelerate the design process and allow for searches over a broad class of materials. The high-throughput screening platform we have developed can run through large numbers of molecules composed of earth-abundant elements and identifies possible metastable structures of a given material. Corresponding isomerization enthalpies associated with the metastable structures are then computed. Using this high-throughput simulation approach, we have discovered molecular structures with high isomerization enthalpies that have the potential to be new candidates for high-energy density STF. We have also discovered physical principles to guide further STF materials design through structural analysis. More broadly, our results illustrate the potential of using high-throughput ab initio simulations to design materials that undergo targeted structural transitions.

Material-mediated pyrogens in medical devices: Applicability of the in vitro Monocyte Activation Test.

PubMed

Borton, Lindsey K; Coleman, Kelly P

2018-06-14

Pyrogenicity presents a challenge to clinicians, medical device manufactures, and regulators. A febrile response may be caused by endotoxin contamination, microbial components other than endotoxin, or chemical agents that generate a material-mediated pyrogenic response. While test methods for the assessment of endotoxin contamination and some microbial components other than endotoxin are well-established, material-mediated pyrogens remain elusively undefined. This review presents the findings of literature searches conducted to identify material-mediated pyrogens associated with medical devices. The in vivo rabbit pyrogen test (RPT) is considered to be the "gold standard" for medical device pyrogenicity testing, despite the fact that few medical device-derived material-mediated pyrogens are known. In line with global efforts to reduce the use of research animals, an in vitro monocyte activation test (MAT) has the potential to replace the RPT. The MAT is used to detect substances that activate human monocytes to release cytokines. This review will also describe the potential opportunities and challenges associated with MAT adoption for the detection of material-mediated pyrogens in medical device testing.

Potential impacts of nanotechnology on energy transmission applications and needs.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elcock, D.; Environmental Science Division

2007-11-30

The application of nanotechnologies to energy transmission has the potential to significantly impact both the deployed transmission technologies and the need for additional development. This could be a factor in assessing environmental impacts of right-of-way (ROW) development and use. For example, some nanotechnology applications may produce materials (e.g., cables) that are much stronger per unit volume than existing materials, enabling reduced footprints for construction and maintenance of electricity transmission lines. Other applications, such as more efficient lighting, lighter-weight materials for vehicle construction, and smaller batteries having greater storage capacities may reduce the need for long-distance transport of energy, and possiblymore » reduce the need for extensive future ROW development and many attendant environmental impacts. This report introduces the field of nanotechnology, describes some of the ways in which processes and products developed with or incorporating nanomaterials differ from traditional processes and products, and identifies some examples of how nanotechnology may be used to reduce potential ROW impacts. Potential environmental, safety, and health impacts are also discussed.« less

HANDBOOK: RECYCLING AND REUSE OF MATERIAL FOUND ON SUPERFUND SITES

EPA Science Inventory

This document provides assistance in identifying potential recycling technologies for a wide variety of contaminants and matrices. Personnel at Superfund and Resource Conservation and Recovery Act (RCRA) Corrective Action sites face the challenge of selecting remedial options for...

10 CFR 835.401 - General requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... DEPARTMENT OF ENERGY OCCUPATIONAL RADIATION PROTECTION Monitoring of Individuals and Areas § 835.401 General... engineered and administrative controls in containing radioactive material and reducing radiation exposure; and (6) Identify and control potential sources of individual exposure to radiation and/or radioactive...

10 CFR 835.401 - General requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... DEPARTMENT OF ENERGY OCCUPATIONAL RADIATION PROTECTION Monitoring of Individuals and Areas § 835.401 General... engineered and administrative controls in containing radioactive material and reducing radiation exposure; and (6) Identify and control potential sources of individual exposure to radiation and/or radioactive...

10 CFR 835.401 - General requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... DEPARTMENT OF ENERGY OCCUPATIONAL RADIATION PROTECTION Monitoring of Individuals and Areas § 835.401 General... engineered and administrative controls in containing radioactive material and reducing radiation exposure; and (6) Identify and control potential sources of individual exposure to radiation and/or radioactive...

10 CFR 835.401 - General requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... DEPARTMENT OF ENERGY OCCUPATIONAL RADIATION PROTECTION Monitoring of Individuals and Areas § 835.401 General... engineered and administrative controls in containing radioactive material and reducing radiation exposure; and (6) Identify and control potential sources of individual exposure to radiation and/or radioactive...

10 CFR 835.401 - General requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... DEPARTMENT OF ENERGY OCCUPATIONAL RADIATION PROTECTION Monitoring of Individuals and Areas § 835.401 General... engineered and administrative controls in containing radioactive material and reducing radiation exposure; and (6) Identify and control potential sources of individual exposure to radiation and/or radioactive...

Computing elastic anisotropy to discover gum-metal-like structural alloys

NASA Astrophysics Data System (ADS)

Winter, I. S.; de Jong, M.; Asta, M.; Chrzan, D. C.

2017-08-01

The computer aided discovery of structural alloys is a burgeoning but still challenging area of research. A primary challenge in the field is to identify computable screening parameters that embody key structural alloy properties. Here, an elastic anisotropy parameter that captures a material's susceptibility to solute solution strengthening is identified. The parameter has many applications in the discovery and optimization of structural materials. As a first example, the parameter is used to identify alloys that might display the super elasticity, super strength, and high ductility of the class of TiNb alloys known as gum metals. In addition, it is noted that the parameter can be used to screen candidate alloys for shape memory response, and potentially aid in the optimization of the mechanical properties of high-entropy alloys.

Emerging Science and Research Opportunities for Metals and Metallic Nanostructures

NASA Astrophysics Data System (ADS)

Handwerker, Carol A.; Pollock, Tresa M.

2014-07-01

During the next decade, fundamental research on metals and metallic nanostructures (MMNs) has the potential to continue transforming metals science into innovative materials, devices, and systems. A workshop to identify emerging and potentially transformative research areas in MMNs was held June 13 and 14, 2012, at the University of California Santa Barbara. There were 47 attendees at the workshop (listed in the Acknowledgements section), representing a broad range of academic institutions, industry, and government laboratories. The metals and metallic nanostructures (MMNs) workshop aimed to identify significant research trends, scientific fundamentals, and recent breakthroughs that can enable new or enhanced MMN performance, either alone or in a more complex materials system, for a wide range of applications. Additionally, the role that MMN research can play in high-priority research and development (R&D) areas such as the U.S. Materials Genome Initiative, the National Nanotechnology Initiative, the Advanced Manufacturing Initiative, and other similar initiatives that exist internationally was assessed. The workshop also addressed critical issues related to materials research instrumentation and the cyberinfrastructure for materials science research and education, as well as science, technology, engineering, and mathematics (STEM) workforce development, with emphasis on the United States but with an appreciation that similar challenges and opportunities for the materials community exist internationally. A central theme of the workshop was that research in MMNs has provided and will continue to provide societal benefits through the integration of experiment, theory, and simulation to link atomistic, nanoscale, microscale, and mesoscale phenomena across time scales for an ever-widening range of applications. Within this overarching theme, the workshop participants identified emerging research opportunities that are categorized and described in more detail in the following sections in terms of the following: three-dimensional (3-D) and four-dimensional (4-D) materials science. Structure evolution and the challenge of heterogeneous and multicomponent systems. The science base for property prediction across the length scales. Nanoscale phenomena at surfaces—experiment, theory, and simulation. Prediction and control of the morphology, microstructure, and properties of "bulk" nanostructured metals. Functionality and control of materials far from equilibrium. Hybrid and multifunctional materials assemblies. Materials discovery and design: enhancing the theory-simulation-experiment loop. Following an introduction, these emerging research opportunities are discussed in detail, along with challenges and opportunities for the materials community in the areas of instrumentation, cyberinfrastructure, education, and workforce development.

Oxygen Concentration Flammability Thresholds of Selected Aerospace Materials Considered for the Constellation Program

NASA Technical Reports Server (NTRS)

Hirsch, David B.; Williams, James H.; Harper, Susan A.; Beeson, Harold; Pedley, Michael D.

2007-01-01

Materials selection for spacecraft is based on an upward flammability test conducted in a quiescent environment in the highest expected oxygen concentration environment. The test conditions and its pass/fail test logic do not provide sufficient quantitative materials flammability information for an advanced space exploration program. A modified approach has been suggested determination of materials self-extinguishment limits. The flammability threshold information will allow NASA to identify materials with increased flammability risk from oxygen concentration and total pressure changes, minimize potential impacts, and allow for development of sound requirements for new spacecraft and extraterrestrial landers and habitats. This paper provides data on oxygen concentration self-extinguishment limits under quiescent conditions for selected materials considered for the Constellation Program.

Analytic materials

PubMed Central

2016-01-01

The theory of inhomogeneous analytic materials is developed. These are materials where the coefficients entering the equations involve analytic functions. Three types of analytic materials are identified. The first two types involve an integer p. If p takes its maximum value, then we have a complete analytic material. Otherwise, it is incomplete analytic material of rank p. For two-dimensional materials, further progress can be made in the identification of analytic materials by using the well-known fact that a 90° rotation applied to a divergence-free field in a simply connected domain yields a curl-free field, and this can then be expressed as the gradient of a potential. Other exact results for the fields in inhomogeneous media are reviewed. Also reviewed is the subject of metamaterials, as these materials provide a way of realizing desirable coefficients in the equations. PMID:27956882

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gorai, Prashun; Toberer, Eric S.; Stevanović, Vladan

Here, at room temperature and above, most magnetic materials adopt a spin-disordered (paramagnetic) state whose electronic properties can differ significantly from their low-temperature, spin-ordered counterparts. Yet computational searches for new functional materials usually assume some type of magnetic order. In the present work, we demonstrate a methodology to incorporate spin disorder in computational searches and predict the electronic properties of the paramagnetic phase. We implement this method in a high-throughput framework to assess the potential for thermoelectric performance of 1350 transition-metal sulfides and find that all magnetic systems we identify as promising in the spin-ordered ground state cease to bemore » promising in the paramagnetic phase due to disorder-induced deterioration of the charge carrier transport properties. We also identify promising non-magnetic candidates that do not suffer from these spin disorder effects. In addition to identifying promising materials, our results offer insights into the apparent scarcity of magnetic systems among known thermoelectrics and highlight the importance of including spin disorder in computational searches.« less

Investigation of test methods, material properties, and processes for solar cell encapsulants. Encapsulation task of the low-cost silicon solar array project

NASA Technical Reports Server (NTRS)

1977-01-01

During this quarter, flat-plate solar collector systems were considered and six basic construction elements were identified: outer coatings, superstrates, pottants, substrates, undercoats, and adhesives. Materials surveys were then initiated to discover either generic classes or/and specific products to function as each construction element. Cost data included in the surveys permit ready evaluation of each material. Silicones, fluorocarbons, glass, and acrylic polymers have the highest inherent weatherability of materials studied to date. Only acrylics, however, combine low costs, environmental resistance, and potential processability. This class will receive particular emphasis.

Composite materials for rail transit systems

NASA Technical Reports Server (NTRS)

Griffin, O. Hayden, Jr.; Guerdal, Zafer; Herakovich, Carl T.

1987-01-01

The potential is explored for using composite materials in urban mass transit systems. The emphasis was to identify specific advantages of composite materials in order to determine their actual and potential usage for carbody and guideway structure applications. The literature was reviewed, contacts were made with major domestic system operators, designers, and builders, and an analysis was made of potential composite application to railcar construction. Composites were found to be in use throughout the transit industry, usually in secondary or auxiliary applications such as car interior and nonstructural exterior panels. More recently, considerable activity has been initiated in the area of using composites in the load bearing elements of civil engineering structures such as highway bridges. It is believed that new and improved manufacturing refinements in pultrusion and filament winding will permit the production of beam sections which can be used in guideway structures. The inherent corrosion resistance and low maintenance characteristics of composites should result in lowered maintenance costs over a prolonged life of the structure.

The green choices project: integrating environmental health education into reproductive health care settings.

PubMed

Worthington, Sandra; Armstrong, Kay; Debevec, Elie

2010-01-01

A national reproductive health organization developed the Green Choices project to educate staff and clients about how to live in healthier environments by reducing potentially harmful environmental exposures to toxicants. An advisory group, comprised of experts in environmental and reproductive health and literacy, defined the project's scope and common environmental exposures to address. The following educational materials were developed: an online staff environmental health 101 curriculum, an environmental health assessment tool for clients to identify their potential risks, and information sheets for each environmental exposure that described potential risks and ways to reduce risks. Beta-testing methods included baseline and follow-up surveys, one-on-one interviews, focus groups, and recommendations from experts. Staff and client feedback on the educational materials resulted in increased clarity, sensitivity, relevancy, and appeal. Environmental health experts ensured accuracy of information, and reading experts lowered the reading level from 12th to 6th grade. A campaign to disseminate environmental health information and educational materials nationally is under way.

Prioritizing stream types according to their potential risk to receive crop plant material--A GIS-based procedure to assist in the risk assessment of genetically modified crops and systemic insecticide residues.

PubMed

Bundschuh, Rebecca; Kuhn, Ulrike; Bundschuh, Mirco; Naegele, Caroline; Elsaesser, David; Schlechtriemen, Ulrich; Oehen, Bernadette; Hilbeck, Angelika; Otto, Mathias; Schulz, Ralf; Hofmann, Frieder

2016-03-15

Crop plant residues may enter aquatic ecosystems via wind deposition or surface runoff. In the case of genetically modified crops or crops treated with systemic pesticides, these materials may contain insecticidal Bt toxins or pesticides that potentially affect aquatic life. However, the particular exposure pattern of aquatic ecosystems (i.e., via plant material) is not properly reflected in current risk assessment schemes, which primarily focus on waterborne toxicity and not on plant material as the route of uptake. To assist in risk assessment, the present study proposes a prioritization procedure of stream types based on the freshwater network and crop-specific cultivation data using maize in Germany as a model system. To identify stream types with a high probability of receiving crop materials, we developed a formalized, criteria-based and thus transparent procedure that considers the exposure-related parameters, ecological status--an estimate of the diversity and potential vulnerability of local communities towards anthropogenic stress--and availability of uncontaminated reference sections. By applying the procedure to maize, ten stream types out of 38 are expected to be the most relevant if the ecological effects from plant-incorporated pesticides need to be evaluated. This information is an important first step to identifying habitats within these stream types with a high probability of receiving crop plant material at a more local scale, including accumulation areas. Moreover, the prioritization procedure developed in the present study may support the selection of aquatic species for ecotoxicological testing based on their probability of occurrence in stream types having a higher chance of exposure. Finally, this procedure can be adapted to any geographical region or crop of interest and is, therefore, a valuable tool for a site-specific risk assessment of crop plants carrying systemic pesticides or novel proteins, such as insecticidal Bt toxins, expressed in genetically modified crops. Copyright © 2015 Elsevier B.V. All rights reserved.

Excitonic gap formation in pumped Dirac materials

NASA Astrophysics Data System (ADS)

Triola, Christopher; Pertsova, Anna; Markiewicz, Robert S.; Balatsky, Alexander V.

2017-05-01

Recent pump-probe experiments demonstrate the possibility that Dirac materials may be driven into transient excited states describable by two chemical potentials, one for the electrons and one for the holes. Given the Dirac nature of the spectrum, such an inverted population allows the optical tunability of the density of states of the electrons and holes, effectively offering control of the strength of the Coulomb interaction. Here we discuss the feasibility of realizing transient excitonic instabilities in optically pumped Dirac materials. We demonstrate, theoretically, the reduction of the critical coupling leading to the formation of a transient condensate of electron-hole pairs and identify signatures of this state. Furthermore, we provide guidelines for experiments by both identifying the regimes in which such exotic many-body states are more likely to be observed and estimating the magnitude of the excitonic gap for a few important examples of existing Dirac materials. We find a set of material parameters for which our theory predicts large gaps and high critical temperatures and which could be realized in future Dirac materials. We also comment on transient excitonic instabilities in three-dimensional Dirac and Weyl semimetals. This study provides an example of a transient collective instability in driven Dirac materials.

Mineral resource potential map of the Sugarloaf Roadless Area, San Bernardino County, California

USGS Publications Warehouse

Powell, Robert E.; Matti, Jonathan C.; Cox, Brett F.; Oliver, Howard W.; Wagini, Alexander; Campbell, Harry W.

1983-01-01

Geologic, geochemical, and geophysical investigations and a survey of mines and prospects indicate that the Sugaloaf Roadless Area contains subeconomic graphite and magnesian marble resources. Parts of the area have a low potential for the occurrence of additional low-grade graphite resources, but there is no potential for additional magnesian marble resources within the roadless area. Sand, gravel, and construction stone other than carbonate rocks are found in the roadless area, but similar or better quality materials are abundant and more accessible outside the area. The roadless area has no identified energy mineral resources, but parts of the area have a low to moderate potential for low-grade uranium resources. There are no identified metallic mineral resources within the area, and there is no evidence of a potential for the occurrence of such resources. No previously unknown mineral occurrence was located during this study.

Mud Volcanoes in the Martian Lowlands: Potential Windows to Fluid-Rich Samples from Depth

NASA Technical Reports Server (NTRS)

Oehler, Dorothy Z.; Allen, Carlton C.

2009-01-01

The regional setting of the Chryse-Acidalia area augurs well for a fluid-rich subsurface, accumulation of diverse rock types reflecting the wide catchment area, astrobiological prospectivity, and mud volcanism. This latter provides a mechanism for transporting samples from relatively great depth to the surface. Since mud volcanoes are not associated with extreme heat or shock pressures, materials they transport to the surface are likely to be relatively unaltered; thus such materials could contain interpretable remnants of potential martian life (e.g., organic chemical biomarkers, mineral biosignatures, or structural remains) as well as unmetamorphosed rock samples. None of the previous landings on Mars was located in an area with features identified as potential mud volcanoes (Fig. 3), but some of these features may offer targets for future missions aimed at sampling deep fluid-rich strata with potential habitable zones.

Comparing results of X-ray diffraction, µ-Raman spectroscopy and neutron diffraction when identifying chemical phases in seized nuclear material, during a comparative nuclear forensics exercise

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rondahl, Stina Holmgren; Pointurier, Fabien; Ahlinder, Linnea

This work presents the results for identification of chemical phases obtained by several laboratories as a part of an international nuclear forensic round-robin exercise. In this work powder X-ray diffraction (p-XRD) is regarded as the reference technique. Neutron diffraction produced a superior high-angle diffraction pattern relative to p-XRD. Requiring only small amounts of sample, µ-Raman spectroscopy was used for the first time in this context as a potentially complementary technique to p-XRD. The chemical phases were identified as pure UO 2 in two materials, and as a mixture of UO 2, U 3O 8 and an intermediate species U 3Omore » 7 in the third material.« less

Comparing results of X-ray diffraction, µ-Raman spectroscopy and neutron diffraction when identifying chemical phases in seized nuclear material, during a comparative nuclear forensics exercise

DOE PAGES

Rondahl, Stina Holmgren; Pointurier, Fabien; Ahlinder, Linnea; ...

2018-01-24

This work presents the results for identification of chemical phases obtained by several laboratories as a part of an international nuclear forensic round-robin exercise. In this work powder X-ray diffraction (p-XRD) is regarded as the reference technique. Neutron diffraction produced a superior high-angle diffraction pattern relative to p-XRD. Requiring only small amounts of sample, µ-Raman spectroscopy was used for the first time in this context as a potentially complementary technique to p-XRD. The chemical phases were identified as pure UO 2 in two materials, and as a mixture of UO 2, U 3O 8 and an intermediate species U 3Omore » 7 in the third material.« less

Plume induced environments on future lunar mission vehicles

NASA Technical Reports Server (NTRS)

Rochelle, Bill; Hughes, Ruston; Fitzgerald, Steve

1992-01-01

The objective of this presentation is to identify potential plume heating/impingement problem areas on vehicles used for future lunar missions. This is accomplished by comparison with lunar module plume investigations performed during 1968-1971. All material is presented in viewgraph format.

Pervious concrete research facility : winter performance and enhancement of pollutants removal.

DOT National Transportation Integrated Search

2013-12-01

The purpose of the current study was to design and test a porous medium that can potentially be applied in : pervious pavement systems. The principle goals were to identify a material capable of enhancing the PAH : sorption capacity, thereby mitigati...

Fiber-reinforced ceramic composites for Earth-to-orbit rocket engine turbines

NASA Technical Reports Server (NTRS)

Brockmeyer, Jerry W.; Schnittgrund, Gary D.

1990-01-01

Fiber reinforced ceramic matrix composites (FRCMC) are emerging materials systems that offer potential for use in liquid rocket engines. Advantages of these materials in rocket engine turbomachinery include performance gain due to higher turbine inlet temperature, reduced launch costs, reduced maintenance with associated cost benefits, and reduced weight. This program was initiated to assess the state of FRCMC development and to propose a plan for their implementation into liquid rocket engine turbomachinery. A complete range of FRCMC materials was investigated relative to their development status and feasibility for use in the hot gas path of earth-to-orbit rocket engine turbomachinery. Of the candidate systems, carbon fiber-reinforced silicon carbide (C/SiC) offers the greatest near-term potential. Critical hot gas path components were identified, and the first stage inlet nozzle and turbine rotor of the fuel turbopump for the liquid oxygen/hydrogen Space Transportation Main Engine (STME) were selected for conceptual design and analysis. The critical issues associated with the use of FRCMC were identified. Turbine blades were designed, analyzed and fabricated. The Technology Development Plan, completed as Task 5 of this program, provides a course of action for resolution of these issues.

Discovery and Characterization of a Pourbaix-Stable, 1.8 eV Direct Gap Bismuth Manganate Photoanode

DOE PAGES

Newhouse, Paul F.; Reyes-Lillo, Sebastian E.; Li, Guo; ...

2017-11-13

Solar-driven oxygen evolution is a critical technology for renewably synthesizing hydrogen- and carbon-containing fuels in solar fuel generators. New photoanode materials are needed to meet efficiency and stability requirements, motivating materials explorations for semiconductors with (i) band-gap energy in the visible spectrum and (ii) stable operation in aqueous electrolyte at the electrochemical potential needed to evolve oxygen from water. Motivated by the oxygen evolution competency of many Mn-based oxides, the existence of several Bi-containing ternary oxide photoanode materials, and the variety of known oxide materials combining these elements with Sm, we explore the Bi-Mn-Sm oxide system for new photoanodes. Throughmore » the use of a ferri/ferrocyanide redox couple in high-throughput screening, BiMn 2O 5 and its alloy with Sm are identified as photoanode materials with a near-ideal optical band gap of 1.8 eV. Using density functional theory-based calculations of the mullite Bi 3+ Mn 3+ Mn 4+O 5 phase, we identify electronic analogues to the well-known BiVO 4 photoanode and demonstrate excellent Pourbaix stability above the oxygen evolution Nernstian potential from pH 4.5 to 15. Lastly, our suite of experimental and computational characterization indicates that BiMn 2O 5 is a complex oxide with the necessary optical and chemical properties to be an efficient, stable solar fuel photoanode.« less

Discovery and Characterization of a Pourbaix-Stable, 1.8 eV Direct Gap Bismuth Manganate Photoanode

DOE Office of Scientific and Technical Information (OSTI.GOV)

Newhouse, Paul F.; Reyes-Lillo, Sebastian E.; Li, Guo

Solar-driven oxygen evolution is a critical technology for renewably synthesizing hydrogen- and carbon-containing fuels in solar fuel generators. New photoanode materials are needed to meet efficiency and stability requirements, motivating materials explorations for semiconductors with (i) band-gap energy in the visible spectrum and (ii) stable operation in aqueous electrolyte at the electrochemical potential needed to evolve oxygen from water. Motivated by the oxygen evolution competency of many Mn-based oxides, the existence of several Bi-containing ternary oxide photoanode materials, and the variety of known oxide materials combining these elements with Sm, we explore the Bi-Mn-Sm oxide system for new photoanodes. Throughmore » the use of a ferri/ferrocyanide redox couple in high-throughput screening, BiMn 2O 5 and its alloy with Sm are identified as photoanode materials with a near-ideal optical band gap of 1.8 eV. Using density functional theory-based calculations of the mullite Bi 3+ Mn 3+ Mn 4+O 5 phase, we identify electronic analogues to the well-known BiVO 4 photoanode and demonstrate excellent Pourbaix stability above the oxygen evolution Nernstian potential from pH 4.5 to 15. Lastly, our suite of experimental and computational characterization indicates that BiMn 2O 5 is a complex oxide with the necessary optical and chemical properties to be an efficient, stable solar fuel photoanode.« less

Identifying Potentially Hazardous Co-orbiting Material of Known NEOs Using Magnetic Signatures Produced in Destructive Collisions

NASA Astrophysics Data System (ADS)

Lai, Hairong; Russell, Christopher; Jia, Yingdong; Wei, Hanying; Connors, Martin

2015-04-01

It is estimated that over 99% of near-Earth objects (NEOs) with diameters of about tens of meters are undiscovered. However, simulations show that they result in the most damage per year. Many of these bodies, produced in non-destructive collisions with larger well-characterized NEOs, are co-orbiting with their parent objects. Thereafter, scattering will occur due to gravitational perturbations when the co-orbiters have close encounters to any planets. Such gravitational scattering may not affect the orbits of the parent body. Therefore "safe" NEOs which have negligible impact probability with the Earth may be accompanied by potentially hazardous co-orbiting material. Those co-orbitals do reveal their existence in collisions with meteoroids, which are numerous and can be as small as tens of centimeters in diameter. Clouds of fine dust/gas particles released in such collisions become charged after generation and interact coherently with the solar wind electromagnetically. The interplanetary magnetic field is then perturbed. The resultant structures have been called interplanetary field enhancements (IFEs). They are readily identified when they pass spacecraft equipped with magnetometers. Although the co-orbitals responsible for the IFEs were disrupted in collisions, they are valid samples of the remaining co-orbiting material. Therefore, we can use IFEs to identify the spatial and mass distribution of such co-orbitals. With statistical studies of IFE occurrence, we identified asteroid 2201 Oljato and asteroid 138175 to have such co-orbiting material. The mass of the co-orbitals can be inferred by combining the results from observations and MHD simulations. Multi-spacecraft simultaneous observations measure the dimensions of the magnetic perturbations and the forces lifting them away from the Sun, while multi-fluid simulations give the accelerations of the perturbations. In summary, our technique not only helps us to identify which NEOs are accompanied by hazardous co-orbitals, but also gives their mass distributions. Although our technique provides only the statistical properties, it indicates where high resolution optical surveys should be obtained in order to identify and track specific hazardous bodies.

Towards a Negative Refractive Index in an Atomic System

NASA Astrophysics Data System (ADS)

Simmons, Zach; Brewer, Nick; Yavuz, Deniz

2014-05-01

The goal of our experiments is to obtain a negative index of refraction in the optical region of the spectrum using an atomic system. The concept of negative refraction, which was first predicted by Veselago more than four decades ago, has recently emerged as a very exciting field of science. Negative index materials exhibit many seemingly strange properties such as electromagnetic vectors forming a left-handed triad. A key potential application for these materials was discovered in 2000 when Pendry predicted that a slab with a negative refractive index can image objects with a resolution far better than the diffraction limit. Thus far, research in negative index materials has primarily focused on meta-materials. The fixed response and often large absorption of these engineered materials motivates our efforts to work in an atomic system. An atomic media offers the potential to be actively modified, for example by changing laser parameters, and can be tuned to cancel absorption. A doped crystal allows for high atomic densities compared to other atomic systems. So far we have identified a transition in such a material, Eu:YSO, as a candidate for these experiments and are performing spectroscopy on this material.

In search of standards to support circularity in product policies: A systematic approach.

PubMed

Tecchio, Paolo; McAlister, Catriona; Mathieux, Fabrice; Ardente, Fulvio

2017-12-01

The aspiration of a circular economy is to shift material flows toward a zero waste and pollution production system. The process of shifting to a circular economy has been initiated by the European Commission in their action plan for the circular economy. The EU Ecodesign Directive is a key policy in this transition. However, to date the focus of access to market requirements on products has primarily been upon energy efficiency. The absence of adequate metrics and standards has been a key barrier to the inclusion of resource efficiency requirements. This paper proposes a framework to boost sustainable engineering and resource use by systematically identifying standardization needs and features. Standards can then support the setting of appropriate material efficiency requirements in EU product policy. Three high-level policy goals concerning material efficiency of products were identified: embodied impact reduction, lifetime extension and residual waste reduction. Through a lifecycle perspective, a matrix of interactions among material efficiency topics (recycled content, re-used content, relevant material content, durability, upgradability, reparability, re-manufacturability, reusability, recyclability, recoverability, relevant material separability) and policy goals was created. The framework was tested on case studies for electronic displays and washing machines. For potential material efficiency requirements, specific standardization needs were identified, such as adequate metrics for performance measurements, reliable and repeatable tests, and calculation procedures. The proposed novel framework aims to provide a method by which to identify key material efficiency considerations within the policy context, and to map out the generic and product-specific standardisation needs to support ecodesign. Via such an approach, many different stakeholders (industry, academics, policy makers, non-governmental organizations etc.) can be involved in material efficiency standards and regulations. Requirements and standards concerning material efficiency would compel product manufacturers, but also help designers and interested parties in addressing the sustainable resource use issue.

It takes one to know one: exploring patient dialogue on rosacea web-based platforms and their potential for significant harm.

PubMed

Riddoch, Laura H

2018-05-10

Rosacea is a non-curable skin condition, leading patients to turn self-management options from web-based platforms. Self-management can be dangerous possibly under-reported. To discover the extent of online material and determine the potential for harm influenced by rosacea internet sources. Material analyzed included search engines, apps, YouTube, forums and Facebook groups. As Facebook and forums were most active, they became the core focus. A passive 'fly on the wall' approach allowed observation of user posts and their content. Three broad categories of dialogue were identified: prescribed medications, non-prescribed remedies and, most commonly, posts aimed to elicit emotional support. From this, positive and negative influences were identified. Negative influences were divided into four domains: physical harm, financial harm, emotional harm, and detrimental influences on patient-doctor relationships. Rosacea patients may be susceptible to rely on peer-generated information. Forums can have detrimental outcomes, primarily due to lack of monitoring and the potential for misplaced trust between fellow sufferers, encouraging others to try potentially harmful alternative remedies. Lack of monitoring allows the spread of inaccurate information, which can result in harm. Medical practitioners should be aware of trending online dialogue and self-treatment remedies to facilitate patient safety.

Classification-free threat detection based on material-science-informed clustering

NASA Astrophysics Data System (ADS)

Yuan, Siyang; Wolter, Scott D.; Greenberg, Joel A.

2017-05-01

X-ray diffraction (XRD) is well-known for yielding composition and structural information about a material. However, in some applications (such as threat detection in aviation security), the properties of a material are more relevant to the task than is a detailed material characterization. Furthermore, the requirement that one first identify a material before determining its class may be difficult or even impossible for a sufficiently large pool of potentially present materials. We therefore seek to learn relevant composition-structure-property relationships between materials to enable material-identification-free classification. We use an expert-informed, data-driven approach operating on a library of XRD spectra from a broad array of stream of commerce materials. We investigate unsupervised learning techniques in order to learn about naturally emergent groupings, and apply supervised learning techniques to determine how well XRD features can be used to separate user-specified classes in the presence of different types and degrees of signal degradation.

Study on HDPE Mixed with Sand as Backfilled Material on Retaining Structure

NASA Astrophysics Data System (ADS)

Talib, Z. A.

2018-04-01

The failure of the retaining wall is closely related to backfill material. Granular soils such as sand and gravel are most suitable backfill material because of its drainage properties. However two basic materials are quite heavy and contribute high amount of lateral loads. This study was to determine the effectiveness High Density Polyethylene (HDPE) as a backfill material. HDPE has a lighter weight compare to the sand. It makes HDPE has potential to be used as backfill material. The objective of this study is to identify the most effective percentage of HDPE to replace sand as a backfill material. The percentage of HDPE used in this study was 20%, 30%, 50%, 75% and also 100%. Testing involved in this study were sieve analysis test, constant head permeability test, direct shear test and relative density test. The result shows that the HDPE can be used as backfilled material and save the cost of backfill material

Thermal design of composite materials high temperature attachments

NASA Technical Reports Server (NTRS)

1972-01-01

The thermal aspects of using filamentary composite materials as primary airframe structures on advanced atmospheric entry spacecraft such as the space shuttle vehicle were investigated to identify and evaluate potential design approaches for maintaining composite structures within allowable temperature limits at thermal protection system (TPS) attachments and/or penetrations. The investigation included: (1) definition of thermophysical data for composite material structures; (2) parametric characterization and identification of the influence of the aerodynamic heating and attachment design parameters on composite material temperatures; (3) conceptual design, evaluation, and detailed thermal analyses of temperature limiting design concepts; and (4) the development of experimental data for assessment of the thermal design methodologies and data used for evaluation of the temperature-limiting design concepts. Temperature suppression attachment concepts were examined for relative merit. The simple isolator was identified as the most weight-effective concept and was selected for detail design, thermal analysis, and testing. Tests were performed on TPS standoff attachments to boron/aluminum, boron/polyimide and graphite/epoxy composite structures.

Using isolated cell wall xylan to identify recalcitrant oligosaccharides

USDA-ARS?s Scientific Manuscript database

Herbaceous biomass is a renewable source of carbohydrates with potential for use in microbial conversion to biofuels. Xylan comprises 20-40% of herbaceous biomass cell wall material and its full depolymerization benefits the economics of bioconversion. To understand the limitations of commercial enz...

Hypervelocity impact testing of advanced materials and structures for micrometeoroid and orbital debris shielding

NASA Astrophysics Data System (ADS)

Ryan, Shannon; Christiansen, Eric L.

2013-02-01

A series of 66 hypervelocity impact experiments have been performed to assess the potential of various materials (aluminium, titanium, copper, stainless steel, nickel, nickel/chromium, reticulated vitreous carbon, silver, ceramic, aramid, ceramic glass, and carbon fibre) and structures (monolithic plates, open-cell foam, flexible fabrics, rigid meshes) for micrometeoroid and orbital debris (MMOD) shielding. Arranged in various single-, double-, and triple-bumper configurations, screening tests were performed with 0.3175 cm diameter Al2017-T4 spherical projectiles at nominally 6.8 km/s and normal incidence. The top performing shields were identified through target damage assessments and their respective weight. The top performing candidate shield at the screening test condition was found to be a double-bumper configuration with a 0.25 mm thick Al3003 outer bumper, 6.35 mm thick 40 PPI aluminium foam inner bumper, and 1.016 mm thick Al2024-T3 rear wall (equal spacing between bumpers and rear wall). In general, double-bumper candidates with aluminium plate outer bumpers and foam inner bumpers were consistently found to be amongst the top performers. For this impact condition, potential weight savings of at least 47% over conventional all-aluminium Whipple shields are possible by utilizing the investigated materials and structures. The results of this study identify materials and structures of interest for further, more in-depth, impact investigations.

Phase Change Material Trade Study: A Comparison Between Wax and Water for Manned Spacecraft

NASA Technical Reports Server (NTRS)

Quinn, Gregory; Hodgson, Ed; Stephan, Ryan

2010-01-01

Phase change material heat sinks have been recognized as an important tool in optimizing thermal control systems for space exploration vehicles and habitats that must deal with widely varying thermal loads and environments. In order to better focus technology investment in this arena, NASA has supported a trade study with the objective of identifying where the best potential pay-off can be found among identified aqueous and paraffin wax phase change materials and phase change material heat sink design approaches. The study used a representative exploration mission with well understood parameters to support the trade. Additional sensitivity studies were performed to ensure the applicability of study results across varying systems and destinations. Results from the study indicate that a water ice PCM heat sink has the potential to decrease the equivalent system mass of the mission s vehicle through a combination of a smaller heat sink and a slight 5% increase in radiator size or the addition of a lightweight heat pump. An evaluation of existing and emerging PCM heat sink technologies indicates that further significant mass savings should be achievable through continued development of those technologies. The largest mass savings may be realized by managing the location of the liquid and the solid in the heat sink to eliminate the melting and freezing pressure of wax and water, respectively, while also accommodating the high structural loads expected on future manned launch vehicles.

Design Two-dimensional Materials with Superb Electronic and Optoelectronic Properties: The case of SiS

NASA Astrophysics Data System (ADS)

Wei, Su-Huai; Yang, Ji-Hui; Zhang, Yueyu; Yin, Wan-Jian; Gong, X. G.; Yakobson, Boris I.

Two-dimensional (2D) semiconductors have many unique electronic and optoelectronic properties that is suitable for novel device applications. Most of the current study are focused on group IV or transition metal chalcogenides. In this study, using atomic transmutation and global optimization methods, we identified two group IV-VI 2D materials, Pma2-SiS and silicene sulfide that can overcome shortcomings encountered in conventional 2D semiconducttord. Pma2-SiS is found to be both chemically, energetically, and thermally stable. Most importantly, Pma2-SiS has unique electronic and optoelectronic properties, including direct bandgaps suitable for solar cells, good mobility for nanoelectronics, good flexibility of property tuning by layer thickness and strain appliance, and good air stability as well. Therefore, Pma2-SiS is expected to be a very promising 2D material in the field of 2D electronics and optoelectronics. Silicene sulfide also shows similar properties. We believe that the designing principles and approaches used to identify these materials have great potential to accelerate future finding of new functional materials within the 2D families.

Factors associated with occupational exposure to biological material among nursing professionals.

PubMed

Negrinho, Nádia Bruna da Silva; Malaguti-Toffano, Silmara Elaine; Reis, Renata Karina; Pereira, Fernanda Maria Vieira; Gir, Elucir

2017-01-01

to identify factors associated with occupational exposure to biological material among nursing professionals. a cross-sectional study was conducted in a high complexity hospital of a city in the state of São Paulo, Brazil. Nursing professionals were interviewed from March to November 2015. All ethical aspects were observed. among the 226 professionals interviewed, 17.3% suffered occupational exposure to potentially contaminated biological material, with 61.5% being percutaneous. Factors such as age (p=0.003), professional experience in nursing (p=0.015), and experience at the institution (p=0.032) were associated with the accidents with biological material. most accidents with biological material among nursing professionals were percutaneous. Age, professional experience, and experience at the institution were considered factors associated with occupational exposure.

Optical isolators for 2-micron fibre lasers

NASA Astrophysics Data System (ADS)

Stevens, Gary; Legg, Thomas H.; Shardlow, Peter

2015-02-01

We report on the development and testing of optical isolators for use in 2-micron fiber laser systems. A variety of potential Faraday rotator materials were characterised to identify the most suitable materials for use in the 1700-2100nm wavelength range. Isolators based on the three best performing materials were then developed and packaged as fiber-in, fiber-out and fiber-in, beam-out devices. The isolators were then tested in CW, pulsed and ultrafast laser systems. The three different designs produced different performance characteristics, but all designs demonstrated isolation >25dB and insertion losses of <1.2 dB.

Carbon Nanotubes Filled with Ferromagnetic Materials

PubMed Central

Weissker, Uhland; Hampel, Silke; Leonhardt, Albrecht; Büchner, Bernd

2010-01-01

Carbon nanotubes (CNT) filled with ferromagnetic metals like iron, cobalt or nickel are new and very interesting nanostructured materials with a number of unique properties. In this paper we give an overview about different chemical vapor deposition (CVD) methods for their synthesis and discuss the influence of selected growth parameters. In addition we evaluate possible growth mechanisms involved in their formation. Moreover we show their identified structural and magnetic properties. On the basis of these properties we present different application possibilities. Some selected examples reveal the high potential of these materials in the field of medicine and nanotechnology. PMID:28883334

The magnitude of impact damage on LDEF materials

NASA Technical Reports Server (NTRS)

Allbrooks, Martha; Atkinson, Dale

1992-01-01

The purpose of this report is to document the magnitude and types of impact damage to materials and systems on the LDEF. This report will provide insights which permit NASA and industry space-systems designers to more rapidly identify potential problems and hazards in placing a spacecraft in low-Earth orbit (LEO). This report is structured to provide (1) a background on LDEF, (2) an introduction to the LEO meteoroid and debris environments, and (3) descriptions of the types of damage caused by impacts into structural materials, and contamination caused by spallation and ejecta from impact events.

Terrorism and hazardous material trucking: promoting perceived collective efficacy for terrorism prevention.

PubMed

James, Keith

2008-01-01

Hazardous-material trucking has recently been identified as an area of high potential risk for terrorism. Some recent theory and case study papers have argued for the importance of collective efficacy to disaster-response, terrorism prevention, and other rare-but-risky events. Therefore, a study based on the collective efficacy literature was done to test an intervention for increasing perceived collective efficacy for terrorism prevention among Canadian hazardous-material truck drivers. Results supported the impact of the intervention in increasing perceived efficacy for terrorism prevention. Implications for theory, research, and application are discussed.

Learning from data to design functional materials without inversion symmetry

PubMed Central

Balachandran, Prasanna V.; Young, Joshua; Lookman, Turab; Rondinelli, James M.

2017-01-01

Accelerating the search for functional materials is a challenging problem. Here we develop an informatics-guided ab initio approach to accelerate the design and discovery of noncentrosymmetric materials. The workflow integrates group theory, informatics and density-functional theory to uncover design guidelines for predicting noncentrosymmetric compounds, which we apply to layered Ruddlesden-Popper oxides. Group theory identifies how configurations of oxygen octahedral rotation patterns, ordered cation arrangements and their interplay break inversion symmetry, while informatics tools learn from available data to select candidate compositions that fulfil the group-theoretical postulates. Our key outcome is the identification of 242 compositions after screening ∼3,200 that show potential for noncentrosymmetric structures, a 25-fold increase in the projected number of known noncentrosymmetric Ruddlesden-Popper oxides. We validate our predictions for 19 compounds using phonon calculations, among which 17 have noncentrosymmetric ground states including two potential multiferroics. Our approach enables rational design of materials with targeted crystal symmetries and functionalities. PMID:28211456

The Use of Carbon-Fiber-Reinforced (CFR) PEEK Material in Orthopedic Implants: A Systematic Review

PubMed Central

Li, Chuan Silvia; Vannabouathong, Christopher; Sprague, Sheila; Bhandari, Mohit

2015-01-01

Carbon-fiber-reinforced polyetheretherketone (CFR-PEEK) has been successfully used in orthopedic implants. The aim of this systematic review is to investigate the properties, technical data, and safety of CFR-PEEK biomaterial and to evaluate its potential for new innovation in the design of articulating medical devices. A comprehensive search in PubMed and EMBASE was conducted to identify articles relevant to the outcomes of CFR-PEEK orthopedic implants. The search was also expanded by reviewing the reference sections of selected papers and references and benchmark reports provided by content experts. A total of 23 articles were included in this review. There is limited literature available assessing the performance of CFR-PEEK, specifically as an implant material for arthroplasty systems. Nevertheless, available studies strongly support CFR-PEEK as a promising and suitable material for orthopedic implants because of its biocompatibility, material characteristics, and mechanical durability. Future studies should continue to investigate CFR-PEEK’s potential benefits. PMID:25780341

Hydrothermal Liquefaction Treatment Hazard Analysis Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lowry, Peter P.; Wagner, Katie A.

Hazard analyses were performed to evaluate the modular hydrothermal liquefaction treatment system. The hazard assessment process was performed in 2 stages. An initial assessment utilizing Hazard Identification and Preliminary Hazards Analysis (PHA) techniques identified areas with significant or unique hazards (process safety-related hazards) that fall outside of the normal operating envelope of PNNL and warranted additional analysis. The subsequent assessment was based on a qualitative What-If analysis. The analysis was augmented, as necessary, by additional quantitative analysis for scenarios involving a release of hazardous material or energy with the potential for affecting the public. The following selected hazardous scenarios receivedmore » increased attention: •Scenarios involving a release of hazardous material or energy, controls were identified in the What-If analysis table that prevent the occurrence or mitigate the effects of the release. •Scenarios with significant consequences that could impact personnel outside the immediate operations area, quantitative analyses were performed to determine the potential magnitude of the scenario. The set of “critical controls” were identified for these scenarios (see Section 4) which prevent the occurrence or mitigate the effects of the release of events with significant consequences.« less

New materials for thermal energy storage in concentrated solar power plants

NASA Astrophysics Data System (ADS)

Guerreiro, Luis; Collares-Pereira, Manuel

2016-05-01

Solar Thermal Electricity (STE) is an important alternative to PV electricity production, not only because it is getting more cost competitive with the continuous growth in installed capacity, engineering and associated innovations, but also, because of its unique dispatch ability advantage as a result of the already well established 2-tank energy storage using molten salts (MS). In recent years, research has been performed, on direct MS systems, to which features like modularity and combinations with other (solid) thermal storage materials are considered with the goal of achieving lower investment cost. Several alternative materials and systems have been studied. In this research, storage materials were identified with thermo-physical data being presented for different rocks (e.g. quartzite), super concrete, and other appropriate solid materials. Among the new materials being proposed like rocks from old quarries, an interesting option is the incorporation of solid waste material from old mines belonging to the Iberian Pyritic Belt. These are currently handled as byproducts of past mine activity, and can potentially constitute an environmental hazard due to their chemical (metal) content. This paper presents these materials, as part of a broad study to improve the current concept of solar energy storage for STE plants, and additionally presents a potentially valuable solution for environmental protection related to re-use of mining waste.

Thermal Microstructural Stability of AZ31 Magnesium after Severe Plastic Deformation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Young, John P.; Askari, Hesam A.; Hovanski, Yuri

2015-03-01

Both equal channel angular pressing and friction stir processing have the ability to refine the grain size of twin roll cast AZ31 magnesium and potentially improve its superplastic properties. This work used isochronal and isothermal heat treatments to investigate the microstructural stability of twin roll cast, equal channel angular pressed and friction stir processed AZ31 magnesium. For both heat treatment conditions, it was found that the twin roll casted and equal channel angular pressed materials were more stable than the friction stir processed material. Calculations of the grain growth kinetics showed that severe plastic deformation processing decreased the activation energymore » for grain boundary motion with the equal channel angular pressed material having the greatest Q value of the severely plastically deformed materials and that increasing the tool travel speed of the friction stir processed material improved microstructural stability. The Hollomon-Jaffe parameter was found to be an accurate means of identifying the annealing conditions that will result in substantial grain growth and loss of potential superplastic properties in the severely plastically deformed materials. In addition, Humphreys’s model of cellular microstructural stability accurately predicted the relative microstructural stability of the severely plastically deformed materials and with some modification, closely predicted the maximum grain size ratio achieved by the severely plastically deformed materials.« less

Research note: Mapping spatial patterns in sewer age, material, and proximity to surface waterways to infer sewer leakage hotspots

USGS Publications Warehouse

Hopkins, Kristina G.; Bain, Daniel J.

2018-01-01

Identifying areas where deteriorating sewer infrastructure is in close proximity to surface waterways is needed to map likely connections between sewers and streams. We present a method to estimate sewer installation year and deterioration status using historical maps of the sewer network, parcel-scale property assessment data, and pipe material. Areas where streams were likely buried into the sewer system were mapped by intersecting the historical stream network derived from a 10-m resolution digital elevation model with sewer pipe locations. Potential sewer leakage hotspots were mapped by identifying where aging sewer pipes are in close proximity (50-m) to surface waterways. Results from Pittsburgh, Pennsylvania (USA), indicated 41% of the historical stream length was lost or buried and the potential interface between sewers and streams is great. The co-location of aging sewer infrastructure (>75 years old) near stream channels suggests that 42% of existing streams are located in areas with a high potential for sewer leakage if sewer infrastructure fails. Mapping the sewer-stream interface provides an approach to better understand areas were failing sewers may contribute a disproportional amount of nutrients and other pathogens to surface waterways.

Environmental Aspects of Use of Recycled Carbon Fiber Composites in Automotive Applications.

PubMed

Meng, Fanran; McKechnie, Jon; Turner, Thomas; Wong, Kok H; Pickering, Stephen J

2017-11-07

The high cost and energy intensity of virgin carbon fiber manufacture provides an opportunity to recover substantial value from carbon fiber reinforced plastic wastes. In this study, we assess the life cycle environmental implications of recovering carbon fiber and producing composite materials as substitutes for conventional and proposed lightweight materials in automotive applications (e.g., steel, aluminum, virgin carbon fiber). Key parameters for the recycled carbon fiber materials, including fiber volume fraction and fiber alignment, are investigated to identify beneficial uses of recycled carbon fiber in the automotive sector. Recycled carbon fiber components can achieve the lowest life cycle environmental impacts of all materials considered, although the actual impact is highly dependent on the design criteria (λ value) of the specific component. Low production impacts associated with recycled carbon fiber components are observed relative to lightweight competitor materials (e.g., aluminum, virgin carbon fiber reinforced plastic). In addition, recycled carbon fiber components have low in-use energy use due to mass reductions and associated reduction in mass-induced fuel consumption. The results demonstrate environmental feasibility of the CFRP recycling materials, supporting the emerging commercialization of CF recycling technologies and identifying significant potential market opportunities in the automotive sector.

Potential countersample materials for in vitro simulation wear testing.

PubMed

Shortall, Adrian C; Hu, Xiao Q; Marquis, Peter M

2002-05-01

Any laboratory investigation of the wear resistance of dental materials needs to consider oral conditions so that in vitro wear results can be correlated with in vivo findings. The choice of the countersample is a critical factor in establishing the pattern of tribological wear and in achieving an efficient in vitro wear testing system. This research investigated the wear behavior and surface characteristics associated with three candidate countersample materials used for in vitro wear testing in order to identify a possible suitable substitute for human dental enamel. Three candidate materials, stainless steel, steatite and dental porcelain were evaluated and compared to human enamel. A variety of factors including hardness, wear surface evolution and frictional coefficients were considered, relative to the tribology of the in vivo situation. The results suggested that the dental porcelain investigated bore the closest similarity to human enamel of the materials investigated. Assessment of potential countersample materials should be based on the essential tribological simulation supported by investigations of mechanical, chemical and structural properties. The selected dental porcelain had the best simulating ability among the three selected countersample materials and this class of material may be considered as a possible countersample material for in vitro wear test purposes. Further studies are required, employing a wider range of dental ceramics, in order to optimise the choice of countersample material for standardized in vitro wear testing.

Detecting special nuclear material using muon-induced neutron emission

NASA Astrophysics Data System (ADS)

Guardincerri, Elena; Bacon, Jeffrey; Borozdin, Konstantin; Matthew Durham, J.; Fabritius, Joseph, II; Hecht, Adam; Milner, Edward C.; Miyadera, Haruo; Morris, Christopher L.; Perry, John; Poulson, Daniel

2015-07-01

The penetrating ability of cosmic ray muons makes them an attractive probe for imaging dense materials. Here, we describe experimental results from a new technique that uses neutrons generated by cosmic-ray muons to identify the presence of special nuclear material (SNM). Neutrons emitted from SNM are used to tag muon-induced fission events in actinides and laminography is used to form images of the stopping material. This technique allows the imaging of SNM-bearing objects tagged using muon tracking detectors located above or to the side of the objects, and may have potential applications in warhead verification scenarios. During the experiment described here we did not attempt to distinguish the type or grade of the SNM.

Development of new materials for turbopump bearings

NASA Technical Reports Server (NTRS)

Maurer, R. E.; Pallini, R. A.

1985-01-01

The life requirement for the angular contact ball bearings in the Space Shuttle Main Engine (SSME) high pressure oxygen turbopump (HPOTP) is 7.5 hours. In actual operation, significantly shorter service life was experienced. The objective is to identify bearing materials and/or materials processing techniques offering signficant potential for extending HPOTP bearing performance life. Interactive thermomechanical analysis of the HPOTP bearing-shaft system was performed with the SHABERTH computer program. Bearing fatigue life, ball-race contact stress, heat generation rate, bulk ring temperatures and circumferential stress in the inner rings were quantified as functions of radial load, thrust load and ball-race contact friction. Criteria established from the output of this analysis are being used for material candidate selection.

Influence of Tribology of Cage Material on Ball Bearing Cage Instability

NASA Astrophysics Data System (ADS)

Servais, S.; Duquenne, M.; Bozet, J.-L.

2013-09-01

By creating a solid lubricant thickness on both bearing races, a cage material of cryogenic ball bearing plays a significant role in the good dynamical behavior of the cage. This role is essential because of the lack of conventional lubricant into this kind of bearing.In this paper, a method able to identify if a particular potential cage material can correctly fulfill its function is described. In other words, if it can lead to a stable movement of the cage. From the identification of fundamental tribological parameters governing the cage behavior, this method presents an example of ranking of such materials. This is based on pin-on-disk tests and on a numerical approach.

Accelerating the Design of Solar Thermal Fuel Materials through High Throughput Simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Y; Grossman, JC

2014-12-01

Solar thermal fuels (STF) store the energy of sunlight, which can then be released later in the form of heat, offering an emission-free and renewable solution for both solar energy conversion and storage. However, this approach is currently limited by the lack of low-cost materials with high energy density and high stability. In this Letter, we present an ab initio high-throughput computational approach to accelerate the design process and allow for searches over a broad class of materials. The high-throughput screening platform we have developed can run through large numbers of molecules composed of earth-abundant elements and identifies possible metastablemore » structures of a given material. Corresponding isomerization enthalpies associated with the metastable structures are then computed. Using this high-throughput simulation approach, we have discovered molecular structures with high isomerization enthalpies that have the potential to be new candidates for high-energy density STF. We have also discovered physical principles to guide further STF materials design through structural analysis. More broadly, our results illustrate the potential of using high-throughput ab initio simulations to design materials that undergo targeted structural transitions.« less

Lunar material resources: An overview

NASA Technical Reports Server (NTRS)

Carter, James L.

1992-01-01

The analysis of returned lunar samples and a comparison of the physical and chemical processes operating on the Moon and on the Earth provide a basis for predicting both the possible types of material resources (especially minerals and rocks) and the physical characteristics of ore deposits potentially available on the Moon. The lack of free water on the Moon eliminates the classes of ore deposits that are most exploitable on Earth; namely, (1) hydrothermal, (2) secondary mobilization and enrichment, (3) precipitation from a body of water, and (4) placer. The types of lunar materials available for exploitation are whole rocks and their contained minerals, regolith, fumarolic and vapor deposits, and nonlunar materials, including solar wind implantations. Early exploitation of lunar material resources will be primarily the use of regolith materials for bulk shielding; the extraction from regolith fines of igneous minerals such as plagioclase feldspars and ilmenite for the production of oxygen, structural metals, and water; and possibly the separation from regolith fines of solar-wind-implanted volatiles. The only element, compound, or mineral, that by itself has been identified as having the economic potential for mining, processing, and return to Earth is helium-3.

Lattice Modeling of Early-Age Behavior of Structural Concrete.

PubMed

Pan, Yaming; Prado, Armando; Porras, Rocío; Hafez, Omar M; Bolander, John E

2017-02-25

The susceptibility of structural concrete to early-age cracking depends on material composition, methods of processing, structural boundary conditions, and a variety of environmental factors. Computational modeling offers a means for identifying primary factors and strategies for reducing cracking potential. Herein, lattice models are shown to be adept at simulating the thermal-hygral-mechanical phenomena that influence early-age cracking. In particular, this paper presents a lattice-based approach that utilizes a model of cementitious materials hydration to control the development of concrete properties, including stiffness, strength, and creep resistance. The approach is validated and used to simulate early-age cracking in concrete bridge decks. Structural configuration plays a key role in determining the magnitude and distribution of stresses caused by volume instabilities of the concrete material. Under restrained conditions, both thermal and hygral effects are found to be primary contributors to cracking potential.

[HIV and the nursing professional in the face of needlestick accidents].

PubMed

Vieira, Mariana; Padilha, Maria Itayra Coelho de Souza

2008-12-01

The goal of this study was to identify the scientific production about work-related needlestick accidents among nursing professionals involving HIV-contaminated biological material, as well as to characterize the pre-existing factors to such accidents, such as procedures occurring after the exposure to potentially HIV-contaminated needlestick material. This is a literature review, whose bibliographic search for keywords was carried out within the LILACS databases from the year 2000 onward. This study confirms that pre-existing factors for the occurrence of work-related needlestick accidents are related to work conditions as much as to individual conditions. In face of these accidents, the nursing workers need to know the conducts concerning post-exposure to potentially HIV-contaminated needlestick material. We conclude that the adoption of standardized precautions when working in healthcare is a fundamental condition for worker safety, independently of their area of expertise, given the increasing number of HIV cases.

Lattice Modeling of Early-Age Behavior of Structural Concrete

PubMed Central

Pan, Yaming; Prado, Armando; Porras, Rocío; Hafez, Omar M.; Bolander, John E.

2017-01-01

The susceptibility of structural concrete to early-age cracking depends on material composition, methods of processing, structural boundary conditions, and a variety of environmental factors. Computational modeling offers a means for identifying primary factors and strategies for reducing cracking potential. Herein, lattice models are shown to be adept at simulating the thermal-hygral-mechanical phenomena that influence early-age cracking. In particular, this paper presents a lattice-based approach that utilizes a model of cementitious materials hydration to control the development of concrete properties, including stiffness, strength, and creep resistance. The approach is validated and used to simulate early-age cracking in concrete bridge decks. Structural configuration plays a key role in determining the magnitude and distribution of stresses caused by volume instabilities of the concrete material. Under restrained conditions, both thermal and hygral effects are found to be primary contributors to cracking potential. PMID:28772590

Using Ultrasonic Lamb Waves To Measure Moduli Of Composites

NASA Technical Reports Server (NTRS)

Kautz, Harold E.

1995-01-01

Measurements of broad-band ultrasonic Lamb waves in plate specimens of ceramic-matrix/fiber and metal-matrix/fiber composite materials used to determine moduli of elasticity of materials. In one class of potential applications of concept, Lamb-wave responses of specimens measured and analyzed at various stages of thermal and/or mechanical processing to determine effects of processing, without having to dissect specimens. In another class, structural components having shapes supporting propagation of Lamb waves monitored ultrasonically to identify signs of deterioration and impending failure.

Thermoelectricity in transition metal compounds: The role of spin disorder

DOE PAGES

Gorai, Prashun; Toberer, Eric S.; Stevanović, Vladan

2016-11-01

Here, at room temperature and above, most magnetic materials adopt a spin-disordered (paramagnetic) state whose electronic properties can differ significantly from their low-temperature, spin-ordered counterparts. Yet computational searches for new functional materials usually assume some type of magnetic order. In the present work, we demonstrate a methodology to incorporate spin disorder in computational searches and predict the electronic properties of the paramagnetic phase. We implement this method in a high-throughput framework to assess the potential for thermoelectric performance of 1350 transition-metal sulfides and find that all magnetic systems we identify as promising in the spin-ordered ground state cease to bemore » promising in the paramagnetic phase due to disorder-induced deterioration of the charge carrier transport properties. We also identify promising non-magnetic candidates that do not suffer from these spin disorder effects. In addition to identifying promising materials, our results offer insights into the apparent scarcity of magnetic systems among known thermoelectrics and highlight the importance of including spin disorder in computational searches.« less

In-situ resource utilization in the design of advanced lunar facilities

NASA Technical Reports Server (NTRS)

1990-01-01

Resource utilization will play an important role in the establishment and support of a permanently manned lunar base. At the University of Houston - College of Architecture and the Sasakawa International Center for Space Architecture, a study team recently investigated the potential use of lunar in-situ materials in the design of lunar facilities. The team identified seven potential lunar construction materials; concrete, sulfur concrete, cast basalt, sintered basalt, glass, fiberglass, and metals. Analysis and evaluation of these materials with respect to their physical properties, processes, energy requirements, resource efficiency, and overall advantages and disadvantages lead to the selection of basalt materials as the more likely construction material for initial use on a lunar base. Basalt materials can be formed out of in-situ lunar regolith, with minor material beneficiation, by a simple process of heating and controlled cooling. The team then conceptualized a construction system that combines lunar regolith sintering and casting to make pressurized structures out of lunar resources. The design uses a machine that simultaneously excavates and sinters the lunar regolith to create a cylindrical hole, which is then enclosed with cast basalt slabs, allowing the volume to be pressurized for use as a living or work environment. Cylinder depths of up to 4 to 6 m in the lunar mare or 10 to 12 m in the lunar highlands are possible. Advantages of this construction system include maximum resource utilization, relatively large habitable volumes, interior flexibility, and minimal construction equipment needs. Conclusions of this study indicate that there is significant potential for the use of basalt, a lunar resource derived construction material, as a low cost alternative to Earth-based materials. It remains to be determined when in lunar base phasing this construction method should be implemented.

Leaching Environmental Assessment Framework to Evaluate Beneficial Use and Disposal Decisions

EPA Science Inventory

LEAF test methods are available for use to characterize the leaching potential over a range of conditions (i.e., pH, liquid-to-solid ratio, and waste form). LEAF characterization tests can be used to evaluate a range of materials to identify leaching behavior across a range of ...

49 CFR 192.917 - How does an operator identify potential threats to pipeline integrity and use the threat...

Code of Federal Regulations, 2010 CFR

2010-10-01

... Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Gas Transmission Pipeline Integrity Management § 192...

Potential Alternatives Report for Validation of Alternative Low-Emission Surface PreparationlDepainting Technologies for Structural Steel

NASA Technical Reports Server (NTRS)

Lewis, Pattie

2006-01-01

For this project, particulates and solvents used during the depainting process of steel structures were the identified hazardous material (HazMat) targeted for elimination or reduction. This Potential Alternatives Report (PAR) provides technical analyses of identified alternatives to the current coating removal processes, criteria used to select alternatives for further analysis, and a list of those alternatives recommended for testing. The initial coating removal alternatives list was compiled using literature searches and center participant recommendations. The involved project participants initially considered fifteen (15) alternatives. In late 2004, stakeholders down-selected the list and identified specific processes as potential alternatives to the current depainting methods. The selected alternatives were: 1. Plastic Blast Media 2. Hard Abrasive Media 3. Sponge Blast Media 4. Mechanical Removal with Vacuum Attachment 5. Liquid Nitrogen 6. Laser Coating Removal Available information about these processes was used to analyze the technical merits and the potential environmental, safety, and occupational health (ESOH) impacts of these methods. A preliminary cost benefit analysis will be performed to determine if implementation of alternative technologies is economically justified. NASA AP2

Potential High-Temperature Shape-Memory-Alloy Actuator Material Identified

NASA Technical Reports Server (NTRS)

Noebe, Ronald D.; Gaydosh, Darrell J.; Biles, Tiffany A.; Garg, Anita

2005-01-01

Shape-memory alloys are unique "smart materials" that can be used in a wide variety of adaptive or "intelligent" components. Because of a martensitic solid-state phase transformation in these materials, they can display rather unusual mechanical properties including shape-memory behavior. This phenomenon occurs when the material is deformed at low temperatures (below the martensite finish temperature, Mf) and then heated through the martensite-to-austenite phase transformation. As the material is heated to the austenite finish temperature Af, it is able to recover its predeformed shape. If a bias is applied to the material as it tries to recover its original shape, work can be extracted from the shape-memory alloy as it transforms. Therefore, shape-memory alloys are being considered for compact solid-state actuation devices to replace hydraulic, pneumatic, or motor-driven systems.

Surface modification: advantages, techniques, and applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Natesan, K.

2000-03-01

Adequate performance of materials at elevated temperatures is a potential problem in many systems within the chemical, petroleum, process, and power-generating industries. Degradation of materials occurs because of interaction between the structural material and the exposure environment. These interactions are generally undesired chemical reactions that can lead to accelerated wastage and alter the functional requirements and/or structural integrity of the materials. Therefore, material selection for high-temperature applications must be based not only on a material strength properties but also on resistance to the complex environments prevalent in the anticipated exposure environment. As plants become larger, the satisfactory performance and reliabilitymore » of components play a greater role in plant availability and economics. However, system designers are becoming increasingly concerned with finding the least expensive material that will satisfactorily perform the design function for the desired service life. This present paper addresses the benefits of surface modification and identified several criteria for selection and application of modified surfaces in the power sector. A brief review is presented on potential methods for modification of surfaces, with the emphasis on coatings. In the final section of the paper, several examples address the requirements of different energy systems and surface modification avenues that have been applied to resolve the issues.« less

Health aspects of the curing of synthetic rubbers.

PubMed Central

Fraser, D A; Rappaport, S

1976-01-01

A commonly used tread rubber formulation was cured in the laboratory under conditions simulating vulcanization in the Bag-O-Matic press. Volatile emissions were collected on charcoal and analyzed by combined GC-mass spectrometry. The compounds identified were either contaminants present in the raw material or reaction products. Some of these compounds were also identified in charcoal tube samples collected in the atmosphere of the industrial operations. Estimates based on the loss of weight of rubber during curing were used to predict airborne concentrations and compared to the concentrations actually found. The literature of the toxicity of raw materials and effluents was reviewed, and no acute or chronic toxicological effects would be anticipated. Information concerning potential carcinogenicity was not available and could not be evaluated. PMID:1026417

Economic Effectiveness of Healthy Potato Planting Material Production with the Use of Simulated Microgravity

NASA Astrophysics Data System (ADS)

Mishchenko, I. A.; Galushko, V. P.; Taran, O. P.

2008-06-01

Research of potato crop productivity under simulated microgravity allows to identify the plants which can become potentially productive under such stress conditions and that might allow to identify the technological parameters of potato production in other space expeditions. One of the traditional practices of planting material treatment against the viruses are the species in vitro. The study of infectious process flow is conducted in the vitro potato in the conditions of clinorotation. The introduction into culture of the meristems from clinostated plants allowed to obtain the regenerants free from the PVX infection. The employment of simulated microgravity for plant remediation reduced the expenditures on the production of in vitro culture 4,5 times, as compared to termoteraphy.

Evaluation of Unbound Engineered Nanoparticles from a Worker Exposure and Environmental Release Perspective

NASA Astrophysics Data System (ADS)

Bunker, K.; Casuccio, G.; Lersch, T.; Ogle, R.; Wahl, L.

2009-12-01

Nanotechnology and the use of unbound engineered nanoparticles (UNP) is a rapidly developing area of materials science. UNP are defined as engineered nanoparticles that are not contained within a matrix that would prevent the nanoparticles from being mobile and a potential source of exposure. At this time there are no regulatory environmental release limits or worker exposure limits for UNP. The Lawrence Berkeley National Laboratory (LBNL) has initiated a study to evaluate worker exposure and potential environmental release of UNP related to various research activities at LBNL. The study is being performed to help identify and manage potential health and safety hazards as well as environmental impacts related to UNP. A key component of the study is the characterization of starting (source) UNP materials to assist in the determination of worker exposure and environmental release. Analysis of the starting materials is being used to establish source signatures. The source signatures will then be used in the evaluation of worker exposure and environmental release. This presentation will provide an overview of the LBNL study with a focus on the methodologies being used to analyze the samples.

Thermoelectric silicides: A review

NASA Astrophysics Data System (ADS)

Nozariasbmarz, Amin; Agarwal, Aditi; Coutant, Zachary A.; Hall, Michael J.; Liu, Jie; Liu, Runze; Malhotra, Abhishek; Norouzzadeh, Payam; Öztürk, Mehmet C.; Ramesh, Viswanath P.; Sargolzaeiaval, Yasaman; Suarez, Francisco; Vashaee, Daryoosh

2017-05-01

Traditional research on thermoelectric materials focused on improving the figure-of-merit z T to enhance the energy conversion efficiency. With further growth and commercialization of thermoelectric technology beyond niche applications, other factors such as materials availability, toxicity, cost, recyclability, thermal stability, chemical and mechanical properties, and ease of fabrication become important for making viable technologies. Several silicide alloys were identified that have the potential to fulfill these requirements. These materials are of interest due to their abundancy in earth’s crust (e.g., silicon), non-toxicity, and good physical and chemical properties. In this paper, an overview of the silicide thermoelectrics from traditional alloys to advanced material structures is presented. In addition, some of the most effective approaches as well as fundamental physical concepts for designing and developing efficient thermoelectric materials are presented and future perspectives are discussed.

Frictional Ignition Testing of Composite Materials

NASA Technical Reports Server (NTRS)

Peralta, Steve; Rosales, Keisa; Robinson, Michael J.; Stoltzfus, Joel

2006-01-01

The space flight community has been investigating lightweight composite materials for use in propellant tanks for both liquid and gaseous oxygen for space flight vehicles. The use of these materials presents some risks pertaining to ignition and burning hazards in the presence of oxygen. Through hazard analysis process, some ignition mechanisms have been identified as being potentially credible. One of the ignition mechanisms was reciprocal friction; however, test data do not exist that could be used to clear or fail these types of materials as "oxygen compatible" for the reciprocal friction ignition mechanism. Therefore, testing was performed at White Sands Test Facility (WSTF) to provide data to evaluate this ignition mechanism. This paper presents the test system, approach, data results, and findings of the reciprocal friction testing performed on composite sample materials being considered for propellant tanks.

e-Biologics: Fabrication of Sustainable Electronics with "Green" Biological Materials.

PubMed

Lovley, Derek R

2017-06-27

The growing ubiquity of electronic devices is increasingly consuming substantial energy and rare resources for materials fabrication, as well as creating expansive volumes of toxic waste. This is not sustainable. Electronic biological materials (e-biologics) that are produced with microbes, or designed with microbial components as the guide for synthesis, are a potential green solution. Some e-biologics can be fabricated from renewable feedstocks with relatively low energy inputs, often while avoiding the harsh chemicals used for synthesizing more traditional electronic materials. Several are completely free of toxic components, can be readily recycled, and offer unique features not found in traditional electronic materials in terms of size, performance, and opportunities for diverse functionalization. An appropriate investment in the concerted multidisciplinary collaborative research required to identify and characterize e-biologics and to engineer materials and devices based on e-biologics could be rewarded with a new "green age" of sustainable electronic materials and devices. Copyright © 2017 Lovley.

Guidance on managing dredged material contaminated with dioxins and furans

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chase, T.; Dillon, T.

Approximately 400 million cubic yards of sediment are dredged from US navigation channels every year. While the vast majority of the dredged material are clean and thereby suitable for aquatic disposal, a portion of the dredged material are contaminated with chemicals that may pose risks to human health and the ecological health of the aquatic environment. Contaminated dredged materials are most frequently found downstream of industrial and municipal sewage-treatment discharges; non-point sources of pollution (e.g., urban and agricultural runoff) also contribute to contamination of dredged materials. An increasing amount of dredged materials are being identified through more sophisticated testing regimesmore » to pose potentially adverse risks to human health and the aquatic environment. One particular class of chemicals that raises concern when regulating dredged material disposal is dioxin, which has been found in sediment in a number of locations, including New Jersey/New York Harbor. Further testing will likely find that dredged materials are contaminated with low levels of dioxin across the country. Decision makers in the EPA and the USACE are guided by numerous statutory mandates and regulations. Within that framework, judgments about the suitability of dredged material for aquatic disposal are made based upon a tiered testing and evaluative process. Recently, the EPA and the USACE have been working to incorporate risk-based evaluation procedures into the dredged material decision-making process. This paper discusses such efforts to date and the preliminary recommendations for evaluating the potential effects of dioxin contaminated dredged material.« less

Characterization of potential mineralization in Afghanistan: four permissive areas identified using imaging spectroscopy data

USGS Publications Warehouse

King, Trude V.V.; Berger, Byron R.; Johnson, Michaela R.

2014-01-01

As part of the U.S. Geological Survey and Department of Defense Task Force for Business and Stability Operations natural resources revitalization activities in Afghanistan, four permissive areas for mineralization, Bamyan 1, Farah 1, Ghazni 1, and Ghazni 2, have been identified using imaging spectroscopy data. To support economic development, the areas of potential mineralization were selected on the occurrence of selected mineral assemblages mapped using the HyMap™ data (kaolinite, jarosite, hydrated silica, chlorite, epidote, iron-bearing carbonate, buddingtonite, dickite, and alunite) that may be indicative of past mineralization processes in areas with limited or no previous mineral resource studies. Approximately 30 sites were initially determined to be candidates for areas of potential mineralization. Additional criteria and material used to refine the selection and prioritization process included existing geologic maps, Landsat Thematic Mapper data, and published literature. The HyMapTM data were interpreted in the context of the regional geologic and tectonic setting and used the presence of alteration mineral assemblages to identify areas with the potential for undiscovered mineral resources. Further field-sampling, mapping, and supporting geochemical analyses are necessary to fully substantiate and verify the specific deposit types in the four areas of potential mineralization.

Abdomen after a Puestow procedure: postoperative CT appearance, complications, and potential pitfalls.

PubMed

Freed, K S; Paulson, E K; Frederick, M G; Keogan, M T; Pappas, T N

1997-06-01

To evaluate the postoperative computed tomographic (CT) appearance, complications, and potential pitfalls after a Puestow procedure (lateral side-to-side pancreaticojejunostomy). Forty CT examinations were performed after the Puestow procedure in 20 patients. Images were retrospectively reviewed by three radiologists. The pancreaticojejunal anastomosis was identified at 30 examinations and was immediately anterior to the pancreatic body or tail. The anastomosis contained fluid or gas on 11 scans and oral contrast material on four scans. On 15 scans, the anastomosis appeared as collapsed bowel without gas, fluid, or oral contrast material. The Roux-en-Y loop was identified on 28 (70%) scans and contained fluid or gas on 16 scans and oral contrast material on six scans. The Roux-en-Y loop appeared as collapsed bowel on six scans. When the anastomosis or Roux-en-Y loop contained fluid and gas, the appearance mimicked that of a pancreatic or parapancreatic abscess. Peripancreatic stranding was present on 28 scans and was due to either ongoing pancreatitis or postoperative change. Complications included 15 transient fluid collections, three abscesses, four pseudocysts, one hematoma, and one small-bowel and Roux-en-Y obstruction. Knowledge of the anatomy after a Puestow procedure is essential for accurate interpretation of CT scans.

Biologically controlled minerals as potential indicators of life

NASA Technical Reports Server (NTRS)

Schwartz, D. E.; Mancinelli, R. L.; Kaneshiro, E.

1991-01-01

Minerals can be produced and deposited either by abiotic or biologic means. Regardless of their origin, mineral crystals reflect the environment conditions (e.g., temperature, pressure, chemical composition, and redox potential) present during crystal formation. Biologically-produced mineral crystals are grown or reworked under the control of their host organism and reflect an environment different from the abiotic environment. In addition, minerals of either biologic or abiotic origin have great longevities. For these reasons, biologically produced minerals have been proposed as biomarkers. Biomarkers are key morphological, chemical, and isotopic signatures of living systems that can be used to determine if life processes have occurred. Studies of biologically controlled minerals produced by the protist, Paramecium tetraurelia, were initiated since techniques have already been developed to culture them and isolate their crystalline material, and methods are already in place to analyze this material. Two direct crystalline phases were identified. One phase, whose chemical composition is high in Mg, was identified as struvite. The second phase, whose chemical composition is high in Ca, has not been previously found occurring naturally and may be considered a newly discovered material. Analyses are underway to determine the characteristics of these minerals in order to compare them with characteristics of these minerals in order to compare them with characteristics of minerals formed abiotically, but with the same chemical composition.

Surface flow visualization using indicators

NASA Technical Reports Server (NTRS)

Crowder, J. P.

1982-01-01

Surface flow visualization using indicators in the cryogenic wind tunnel which requires a fresh look at materials and procedures to accommodate the new test conditions is described. Potential liquid and gaseous indicators are identified. The particular materials illustrate the various requirements an indicator must fulfill. The indicator must respond properly to the flow phenomenon of interest and must be observable. Boundary layer transition is the most important phenomenon for which flow visualization indicators may be employed. The visibility of a particular indicator depends on utilizing various optical or chemical reactions. Gaseous indicators are more difficult to utilize, but because of their diversity may present unusual and useful opportunities. Factors to be considered in selecting an indicator include handling safety, toxicity, potential for contamination of the tunnel, and cost.

Refractory Materials for Flame Deflector Protection System Corrosion Control: Coatings Systems Literature Survey

NASA Technical Reports Server (NTRS)

Calle, Luz M.; Hintze, Paul E.; Parlier, Christopher R.; Sampson, Jeffrey W.; Coffman, Brekke E.; Coffman, Brekke E.; Curran, Jerome P.; Kolody, Mark R.; Whitten, Mary; Perisich, Steven;

Facility for orbital material processing

NASA Astrophysics Data System (ADS)

Starodubov, D.; McCormick, K.; Dellosa, M.; Erdelyi, E.; Volfson, L.

2018-05-01

The sustainable orbital manufacturing with commercially viable and profitable operation has tremendous potential for driving the space exploration industry and human expansion into outer space. This highly challenging task has never been accomplished before. The current relatively high delivery cost of materials represents the business challenge of value proposition for making products in space. FOMS Inc. team identified an opportunity of fluoride optical fiber manufacturing in space that can lead to the first commercial production on orbit. To address continued cost effective International Space Station (ISS) operations FOMS Inc. has developed and demonstrated for the first time a fully operational space facility for orbital remote manufacturing with up to 50 km fiber fabrication capability and strong commercial potential for manufacturing operations on board the ISS.

Standard Operational Protocols in professional nursing practice: use, weaknesses and potentialities.

PubMed

Sales, Camila Balsero; Bernardes, Andrea; Gabriel, Carmen Silvia; Brito, Maria de Fátima Paiva; Moura, André Almeida de; Zanetti, Ariane Cristina Barboza

2018-01-01

to evaluate the use of Standard Operational Protocols (SOPs) in the professional practice of the nursing team based on the theoretical framework of Donabedian, as well as to identify the weaknesses and potentialities from its implementation. Evaluative research, with quantitative approach performed with nursing professionals working in the Health Units of a city of São Paulo, composed of two stages: document analysis and subsequent application of a questionnaire to nursing professionals. A total of 247 nursing professionals participated and reported changes in the way the interventions were performed. The main weaknesses were the small number of professionals, inadequate physical structure and lack of materials. Among the potentialities were: the standardization of materials and concern of the manager and professional related to patient safety. The reassessment of SOPs is necessary, as well as the adoption of a strategy of permanent education of professionals aiming at improving the quality of care provided.

Investigation of Test Methods, Material Properties and Processes for Solar Cell Encapsulants

NASA Technical Reports Server (NTRS)

Willis, P.; Baum, B.

1982-01-01

The evaluation of potentially useful low cost encapsulation materials is discussed. The goal is to identify, evaluate, test and recommend encapsulant materials and processes for the production of cost effective, long life solar cell modules. Technical investigations concerned the development of advanced cure chemistries for lamination type pottants; the continued evaluation of soil resistant surface treatment, and the results of an accelerated aging test program for the comparison of material stabilities. New compounds were evaluated for efficiency in curing both ethylene/vinyl acetate and ethylene/methyl acrylate pottants intended for vacuum bag lamination of solar cells. Two component aliphatic urethane casting syrups were evaluated for suitability as solar module pottants on the basis of optical, physical and fabrication characteristics.

Models and materials for generalized Kitaev magnetism

NASA Astrophysics Data System (ADS)

Winter, Stephen M.; Tsirlin, Alexander A.; Daghofer, Maria; van den Brink, Jeroen; Singh, Yogesh; Gegenwart, Philipp; Valentí, Roser

2017-12-01

The exactly solvable Kitaev model on the honeycomb lattice has recently received enormous attention linked to the hope of achieving novel spin-liquid states with fractionalized Majorana-like excitations. In this review, we analyze the mechanism proposed by Jackeli and Khaliullin to identify Kitaev materials based on spin-orbital dependent bond interactions and provide a comprehensive overview of its implications in real materials. We set the focus on experimental results and current theoretical understanding of planar honeycomb systems (Na2IrO3, α-Li2IrO3, and α-RuCl3), three-dimensional Kitaev materials (β- and γ-Li2IrO3), and other potential candidates, completing the review with the list of open questions awaiting new insights.

Molecular-level understanding of the carbonisation of polysaccharides.

PubMed

Shuttleworth, Peter S; Budarin, Vitaliy; White, Robin J; Gun'ko, Vladimir M; Luque, Rafael; Clark, James H

2013-07-08

Understanding of both the textural and functionality changes occurring during (mesoporous) polysaccharide carbonisation at the molecular level provides a deeper insight into the whole spectrum of material properties, from chemical activity to pore shape and surface energy, which is crucial for the successful application of carbonaceous materials in adsorption, catalysis and chromatography. Obtained information will help to identify the most appropriate applications of the carbonaceous material generated during torrefaction and different types of pyrolysis processes and therefore will be important for the development of cost- and energy-efficient zero-waste biorefineries. The presented approach is informative and semi-quantitative with the potential to be extended to the formation of other biomass-derived carbonaceous materials. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A promising new thermoelectric material - Ruthenium silicide

NASA Technical Reports Server (NTRS)

Vining, Cronin B.; Mccormack, Joseph A.; Zoltan, Andrew; Zoltan, Leslie D.

1991-01-01

Experimental and theoretical efforts directed toward increasing thermoelectric figure of merit values by a factor of 2 or 3 have been encouraging in several respects. An accurate and detailed theoretical model developed for n-type silicon-germanium (SiGe) indicates that ZT values several times higher than currently available are expected under certain conditions. These new, high ZT materials are expected to be significantly different from SiGe, but not unreasonably so. Several promising candidate materials have been identified which may meet the conditions required by theory. One such candidate, ruthenium silicide, currently under development at JPL, has been estimated to have the potential to exhibit figure of merit values 4 times higher than conventional SiGe materials. Recent results are summarized.

Recent progress towards developing a high field, high-T(sub c) superconducting magnet for magnetic suspension and balance systems

NASA Technical Reports Server (NTRS)

Derochemont, L. Pierre; Oakes, Carlton E.; Squillante, Michael R.; Duan, Hong-Min; Hermann, Allen M.; Andrews, Robert J.; Poeppel, Roger B.; Maroni, Victor A.; Carlberg, Ingrid A.; Kelliher, Warren C.

1992-01-01

This paper reviews superconducting magnets and high T(sub c) superconducting oxide ceramic materials technology to identify areas of fundamental impasse to the fabrication of components and devices that tap what are believed to be the true potential of these new materials. High T(sub c) ceramics pose problems in fundamentally different areas which need to be solved unlike low T(sub c) materials. The authors map out an experimental plan designed to research process technologies which, if suitably implemented, should allow these deficiencies to be solved. Finally, assessments are made of where and on what regimes magnetic system designers should focus their attention to advance the practical development of systems based on these new materials.

Database for CO2 Separation Performances of MOFs Based on Computational Materials Screening.

PubMed

Altintas, Cigdem; Avci, Gokay; Daglar, Hilal; Nemati Vesali Azar, Ayda; Velioglu, Sadiye; Erucar, Ilknur; Keskin, Seda

2018-05-23

Metal-organic frameworks (MOFs) are potential adsorbents for CO 2 capture. Because thousands of MOFs exist, computational studies become very useful in identifying the top performing materials for target applications in a time-effective manner. In this study, molecular simulations were performed to screen the MOF database to identify the best materials for CO 2 separation from flue gas (CO 2 /N 2 ) and landfill gas (CO 2 /CH 4 ) under realistic operating conditions. We validated the accuracy of our computational approach by comparing the simulation results for the CO 2 uptakes, CO 2 /N 2 and CO 2 /CH 4 selectivities of various types of MOFs with the available experimental data. Binary CO 2 /N 2 and CO 2 /CH 4 mixture adsorption data were then calculated for the entire MOF database. These data were then used to predict selectivity, working capacity, regenerability, and separation potential of MOFs. The top performing MOF adsorbents that can separate CO 2 /N 2 and CO 2 /CH 4 with high performance were identified. Molecular simulations for the adsorption of a ternary CO 2 /N 2 /CH 4 mixture were performed for these top materials to provide a more realistic performance assessment of MOF adsorbents. The structure-performance analysis showed that MOFs with Δ Q st 0 > 30 kJ/mol, 3.8 Å < pore-limiting diameter < 5 Å, 5 Å < largest cavity diameter < 7.5 Å, 0.5 < ϕ < 0.75, surface area < 1000 m 2 /g, and ρ > 1 g/cm 3 are the best candidates for selective separation of CO 2 from flue gas and landfill gas. This information will be very useful to design novel MOFs exhibiting high CO 2 separation potentials. Finally, an online, freely accessible database https://cosmoserc.ku.edu.tr was established, for the first time in the literature, which reports all of the computed adsorbent metrics of 3816 MOFs for CO 2 /N 2 , CO 2 /CH 4 , and CO 2 /N 2 /CH 4 separations in addition to various structural properties of MOFs.

Uranium Mining and Norm in North America-Some Perspectives on Occupational Radiation Exposure.

PubMed

Brown, Steven H; Chambers, Douglas B

2017-07-01

All soils and rocks contain naturally occurring radioactive materials (NORM). Many ores and raw materials contain relatively elevated levels of natural radionuclides, and processing such materials can further increase the concentrations of naturally occurring radionuclides. In the U.S., these materials are sometimes referred to as technologically-enhanced naturally occurring radioactive materials (TENORM). Examples of NORM minerals include uranium ores, monazite (a source of rare earth minerals), and phosphate rock used to produce phosphate fertilizer. The processing of these materials has the potential to result in above-background radiation exposure to workers. Following a brief review of the sources and potential for worker exposure from NORM in these varied industries, this paper will then present an overview of uranium mining and recovery in North America, including discussion on the mining methods currently being used for both conventional (underground, open pit) and in situ leach (ISL), also referred to as In Situ Recovery (ISR), and the production of NORM materials and wastes associated with these uranium recovery methods. The radiological composition of the NORM products and wastes produced and recent data on radiological exposures received by workers in the North American uranium recovery industry are then described. The paper also identifies the responsible government agencies in the U.S. and Canada assigned the authority to regulate and control occupational exposure from these NORM materials.

The Application of Coconut Fiber as Dissipative Silencer

NASA Astrophysics Data System (ADS)

Madlan, M. A.; Ghazali, M. I.; Zaman, I.; Kasron, M. Z.; Ying, T. C.

2017-01-01

Heat ventilation air conditioning system (HVAC) is one of the ducting systems that broadly applied in the building. There are HVAC silencers in the market, however the sound absorptive material commonly used is mineral wool. In this research study, a sound absorptive material made of coconut fiber was tested to identify its performance as a potential replacement of green material for ducting silencer. The experiment was carried out in a testing apparatus that follows the BS EN ISO 11691:2009 standard. Different configurations of sound absorptive material and contents of coconut fiber were investigated in the study. The trend of insertion loss at 1/3 octave frequency was identified where at frequency below 3000Hz, the insertion loss of dissipative silencer is observed high at certain frequency with a very narrow range. At 3000Hz, the insertion loss of 4dB to 6dB is constant until 4000Hz and drops until 5000Hz before it increases again steadily up to 13dB at 10000Hz. A similar trend was observed for different configuration of sound absorptive material. Despite the configuration different, the outcome shows that the insertion loss is increasing with higher content of coconut fiber.

Characterizing Salmonella Contamination in Two Rendering Processing Plants.

PubMed

Gong, Chao; Jiang, Xiuping

2017-02-01

A microbiological investigation on Salmonella contamination was conducted in two U.S. rendering plants to investigate the potential cross-contamination of Salmonella in the rendering processing environment. Sampling locations were predetermined at the areas where Salmonella contamination may potentially occur, including raw materials receiving, crax (rendered materials before grinding process) grinding, and finished meal loading-out areas. Salmonella was either enumerated directly on xylose lysine Tergitol 4 agar plates or enriched in Rappaport-Vassiliadis and tetrathionate broths. The presumptive Salmonella isolates were confirmed using CHROMagar plating and latex agglutination testing and then characterized using pulsed-field gel electrophoresis, serotyping, and biofilm-forming determination. Among 108 samples analyzed, 79 (73%) samples were Salmonella positive after enrichment. Selected Salmonella isolates (n = 65) were assigned to 31 unique pulsed-field gel electrophoresis patterns, with 16 Salmonella serotypes, including Typhimurium and Mbandaka, identified as predominant serotypes and 10 Salmonella strains determined as strong biofilm formers. Our results indicated that the raw materials receiving area was the primary source of Salmonella and that the surfaces surrounding crax grinding and finished meal loading-out areas harbor Salmonella in biofilms that may recontaminate the finished meals. The same Salmonella serotypes found in both raw materials receiving and the finished meal loading-out areas suggested a potential of cross-contamination between different areas in the rendering processing environment.

Fatigue behavior and life prediction of a SiC/Ti-24Al-11Nb composite under isothermal conditions. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Bartolotta, Paul A.

1991-01-01

Metal Matrix Composites (MMC) and Intermetallic Matrix Composites (IMC) were identified as potential material candidates for advanced aerospace applications. They are especially attractive for high temperature applications which require a low density material that maintains its structural integrity at elevated temperatures. High temperature fatigue resistance plays an important role in determining the structural integrity of the material. This study attempts to examine the relevance of test techniques, failure criterion, and life prediction as they pertain to an IMC material, specifically, unidirectional SiC fiber reinforced titanium aluminide. A series of strain and load controlled fatigue tests were conducted on unidirectional SiC/Ti-24Al-11Nb composite at 425 and 815 C. Several damage mechanism regimes were identified by using a strain-based representation of the data, Talreja's fatigue life diagram concept. Results of these tests were then used to address issues of test control modes, definition of failure, and testing techniques. Finally, a strain-based life prediction method was proposed for an IMC under tensile cyclic loadings at elevated temperatures.

Micromechanical models to guide the development of synthetic ‘brick and mortar’ composites

NASA Astrophysics Data System (ADS)

Begley, Matthew R.; Philips, Noah R.; Compton, Brett G.; Wilbrink, David V.; Ritchie, Robert O.; Utz, Marcel

2012-08-01

This paper describes a micromechanical analysis of the uniaxial response of composites comprising elastic platelets (bricks) bonded together with thin elastic perfectly plastic layers (mortar). The model yields closed-form results for the spatial variation of displacements in the bricks as a function of constituent properties, which can be used to calculate the effective properties of the composite, including elastic modulus, strength and work-to-failure. Regime maps are presented which indicate critical stresses for failure of the bricks and mortar as a function of constituent properties and brick architecture. The solution illustrates trade-offs between elastic modulus, strength and dissipated work that are a result of transitions between various failure mechanisms associated with brick rupture and rupture of the interfaces. Detailed scaling relationships are presented with the goal of providing material developers with a straightforward means to identify synthesis targets that balance competing mechanical behaviors and optimize material response. Ashby maps are presented to compare potential brick and mortar composites with existing materials, and identify future directions for material development.

Food-processes wastewaters treatment using food solid-waste materials as adsorbents or absorbents

NASA Astrophysics Data System (ADS)

Rapti, Ilaira; Georgopoulos, Stavros; Antonopoulou, Maria; Konstantinou, Ioannis; Papadaki, Maria

2016-04-01

The wastewaters generated by olive-mills during the production of olive oil, wastewaters from a dairy and a cow-farm unit and wastewaters from a small food factory have been treated by means of selected materials, either by-products of the same units, or other solid waste, as absorbents or adsorbents in order to identify the capacity of those materials to remove organic load and toxicity from the aforementioned wastewaters. The potential of both the materials used as absorbents as well as the treated wastewaters to be further used either as fertilizers or for agricultural irrigation purposes are examined. Dry olive leaves, sheep wool, rice husks, etc. were used either in a fixed-bed or in a stirred batch arrangemen,t employing different initial concentrations of the aforementioned wastewaters. The efficiency of removal was assessed using scpectrophotometric methods and allium test phytotoxicity measurements. In this presentation the response of each material employed is shown as a function of absorbent/adsorbent quantity and kind, treatment time and wastewater kind and initial organic load. Preliminary results on the potential uses of the adsorbents/absorbents and the treated wastewaters are also shown. Keywords: Olive-mill wastewaters, dairy farm wastewaters, olive leaves, zeolite, sheep wool

Virtual screening of inorganic materials synthesis parameters with deep learning

NASA Astrophysics Data System (ADS)

Kim, Edward; Huang, Kevin; Jegelka, Stefanie; Olivetti, Elsa

2017-12-01

Virtual materials screening approaches have proliferated in the past decade, driven by rapid advances in first-principles computational techniques, and machine-learning algorithms. By comparison, computationally driven materials synthesis screening is still in its infancy, and is mired by the challenges of data sparsity and data scarcity: Synthesis routes exist in a sparse, high-dimensional parameter space that is difficult to optimize over directly, and, for some materials of interest, only scarce volumes of literature-reported syntheses are available. In this article, we present a framework for suggesting quantitative synthesis parameters and potential driving factors for synthesis outcomes. We use a variational autoencoder to compress sparse synthesis representations into a lower dimensional space, which is found to improve the performance of machine-learning tasks. To realize this screening framework even in cases where there are few literature data, we devise a novel data augmentation methodology that incorporates literature synthesis data from related materials systems. We apply this variational autoencoder framework to generate potential SrTiO3 synthesis parameter sets, propose driving factors for brookite TiO2 formation, and identify correlations between alkali-ion intercalation and MnO2 polymorph selection.

Spectroscopy of Moses Rock Kimberlite Diatreme

NASA Technical Reports Server (NTRS)

Pieters, C. M.; Mustard, J. F.

1985-01-01

Three types of remote sensing data (Airborne Imaging Spectroscopy (AIS), NS001, Zeiss IR-photographs) were obtained for the Moses Rock kimberlite dike in southern Utah. The goal is to identify and characterize the mantle derived mafic component in such volcanic features. The Zeiss and NS001 images provide information on the regional setting and allow units of the dike to be distinguished from surrounding material. A potential unmapped satellite dike was identified. The AIS data provide characterizing information of the surface composition of the dike. Serpentized olivine-bearing soils are (tentatively) identified from the AIS spectra for a few areas within the dike.

Improved metal-adhesive polymers from copper(I)-catalyzed azide-alkyne cycloaddition.

PubMed

Accurso, Adrian A; Delaney, Mac; O'Brien, Jeff; Kim, Hyonny; Iovine, Peter M; Díaz Díaz, David; Finn, M G

2014-08-18

Electrically conductive adhesive polymers offer many potential advantages relative to Sn-Pb solders, including reduced toxicity, low cost, low processing temperatures, and the ability to make application-specific formulations. Polymers generated from the copper(I)-catalyzed cycloaddition (CuAAC) reaction between multivalent azides and alkynes have previously been identified as strong metal-binding adhesives. Herein we demonstrate that the performance of these materials can be remarkably improved by the incorporation of a flexibility-inducing difunctionalized component and a tertiary amine additive in optimized concentrations. The best formulations were identified by means of rapid adhesion testing of a library of potential candidates by using a custom-built instrument and validated in an American Society for Testing and Materials (ASTM)-standard lap-shear test. Characteristic phase transitions were identified by differential scanning calorimetry (DSC) for adhesives with and without the additives as a function of curing temperature. The incorporation of flexible components was found to more than double the strength of the adhesive. Moreover, the adhesive was made electrically conductive by the inclusion of 20 wt% silver-coated copper flakes and further improved in this regard by the incorporation of multiwalled carbon nanotubes in the formulation. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Emergence of psychotic content in psychotherapy: An exploratory qualitative analysis of content, process, and therapist variables in a single case study.

PubMed

Leonhardt, Bethany L; Kukla, Marina; Belanger, Elizabeth; Chaudoin-Patzoldt, Kelly A; Buck, Kelly D; Minor, Kyle S; Vohs, Jenifer L; Hamm, Jay A; Lysaker, Paul H

2018-03-01

Emerging integrative metacognitive therapies for schizophrenia seek to promote subjective aspects of recovery. Beyond symptom remission, they are concerned with shared meaning-making and intersubjective processes. It is unclear, however, how such therapies should understand and respond to psychotic content that threatens meaning-making in therapeutic contexts. Accordingly, we sought to understand what factors precede and potentially trigger psychotic content within psychotherapy and what aids in resolution and return to meaning-making. Forty-eight transcripts from a single psychotherapy case were analyzed with thematic analysis. Passages of delusional or disorganized content were identified and themes present prior to the emergence and resolution of such material were identified and coded. Themes that preceded the emergence of psychotic content varied across early, middle, and late phases of therapy. Material related to the patient's experience of inadequacy and potential vulnerability, therapist setting boundaries within the therapeutic relationship and making challenges appeared to trigger psychotic content, especially early in treatment. Psychotic content may emerge in session following identifiable antecedents which change over phases of therapy. Attending to psychotic content by assuming a non-hierarchical stance and not dismissing psychotic content may aid in maintaining intersubjectivity and support patient's movements toward recovery in integrative metacognitive therapies.

Radiation and shielding study for the International Ultraviolet Explorer

NASA Technical Reports Server (NTRS)

Baze, M.; Firminhac, R. H.; Horne, W. E.; Kennedy, R. C.; Measel, P. R.; Sivo, L. L.; Wilkinson, M. C.

1974-01-01

Technical advisory services to ensure integrity of parts and material exposed to energetic particle radiation for the IUE scientific instruments, spacecraft, and subsystems are provided. A significant potential for interference, degradation, or failure for unprotected or sensitive items was found. Vulnerable items were identified, and appropriate tests, changes, and shields were defined.

Research on Reading of Ink Print by the Blind.

ERIC Educational Resources Information Center

Weisgerber, Robert A.; Everett, Bruce E.

Reviewed is an American Institutes for Research (AIR) study to identify predictors of Optacon success and to develop and field test appropriate Optacon training materials for use by 112 blind elementary and secondary students in 15 U.S. public and residential schools. Potential use of the Optacon (an optical to tactile conversion device that…

Developing Student Potential in the 1990's. A Strategic Plan for Centralia College.

ERIC Educational Resources Information Center

Centralia Coll., WA.

This strategic planning report was prepared by Centralia College (CC) in order to assess the college's internal and external environment, identify problems, and prescribe recommendations. Material for the report was compiled by eight committees/task forces concerned with: (1) strategic planning; (2) institutional mission, philosophy, and goals;…

Product Safety, It's No Accident. A Consumer Product Safety Monthly Planning Guide for Community Organizations.

ERIC Educational Resources Information Center

Consumer Product Safety Commission, Washington, DC.

A consumer product safety monthly planning guide for community organizations is provided. The material is organized into suggested monthly topics with seasonal emphasis. Each section highlights selected information about how to identify potential hazards associated with categories of products. Each section also includes recommendaitons of ways to…

Studying Visual Displays: How to Instructionally Support Learning

ERIC Educational Resources Information Center

Renkl, Alexander; Scheiter, Katharina

2017-01-01

Visual displays are very frequently used in learning materials. Although visual displays have great potential to foster learning, they also pose substantial demands on learners so that the actual learning outcomes are often disappointing. In this article, we pursue three main goals. First, we identify the main difficulties that learners have when…

Market projections of cellulose nanomaterial-enabled products- Part 1: Applications

Treesearch

Jo Anne Shatkin; Theodore H. Wegner; E.M. (Ted) Bilek; John Cowie

2014-01-01

Nanocellulose provides a new materials platform for the sustainable production of high-performance nano-enabled products in an array of applications. In this paper, potential applications for cellulose nanomaterials are identified as the first step toward estimating market volume. The overall study, presented in two parts, estimates market volume on the basis of...

Combining computation and experiment to accelerate the discovery of new hydrogen storage materials

NASA Astrophysics Data System (ADS)

Siegel, Donald

2009-03-01

The potential of emerging technologies such as fuel cells (FCs) and photovoltaics for environmentally-benign power generation has sparked renewed interest in the development of novel materials for high density energy storage. For applications in the transportation sector, the demands placed upon energy storage media are especially stringent, as a potential replacement for fossil-fuel-powered internal combustion engines -- namely, the proton exchange membrane FC -- utilizes hydrogen as a fuel. Although hydrogen has about three times the energy density of gasoline by weight, its volumetric energy density (even at 700 bar) is roughly a factor of six smaller. Consequently, the safe and efficient storage of hydrogen has been identified as one of the key materials-based challenges to realizing a transition to FC vehicles. This talk will present an overview of recent efforts at Ford aimed at developing new materials for reversible, solid state hydrogen storage. A tight coupling between first-principles modeling and experiments has greatly accelerated our efforts, and several examples illustrating the benefits of this approach will be presented.

Investigation of test methods, material properties and processes for solar cell encapsulants

NASA Technical Reports Server (NTRS)

Willis, P. B.; Baum, B.

1977-01-01

The potentially useful encapsulating materials for Task 3 of the Low-Cost Silicon Solar Array project were studied to identify, evaluate, and recommend encapsulant materials and processes for the production of cost-effective, long-life solar cell modules. Materials for study were chosen on the basis of existing knowledge of generic chemical types having high resistance to environmental weathering. The materials varied from rubbers to thermoplastics and presented a broad range of mechanical properties and processing requirements. Basic physical and optical properties were measured on the polymers and were redetermined after exposure to indoor artificial accelerated aging conditions covering four time periods. Strengths and weaknesses of the various materials were revealed and data was accumulated for the development of predictive methodologies. To date, silicone rubbers, fluorocarbons, and acrylic polymers appear to have the most promising combination of characteristics. The fluorocarbons may be used only as films, however, because of their high cost.

Hyperspectral depth-profiling with deep Raman spectroscopy for detecting chemicals in building materials.

PubMed

Cho, Youngho; Song, Si Won; Sung, Jiha; Jeong, Young-Su; Park, Chan Ryang; Kim, Hyung Min

2017-09-25

Toxic chemicals inside building materials have long-term harmful effects on human bodies. To prevent secondary damage caused by the evaporation of latent chemicals, it is necessary to detect the chemicals inside building materials at an early stage. Deep Raman spectroscopy is a potential candidate for on-site detection because it can provide molecular information about subsurface components. However, it is very difficult to spectrally distinguish the Raman signal of the internal chemicals from the background signal of the surrounding materials and to acquire the geometric information of chemicals. In this study, we developed hyperspectral wide-depth spatially offset Raman spectroscopy coupled with a data processing algorithm to identify toxic chemicals, such as chemical warfare agent (CWA) simulants in building materials. Furthermore, the spatial distribution of the chemicals and the thickness of the building material were also measured from one-dimensional (1D) spectral variation.

Cape fearless.

PubMed

1998-01-01

This article describes the Ilita Labantu (IL) group in South Africa, that is working to reduce child abuse and violence against women. The group started in 1989, with the aim of reducing child rape and sexual assaults in five townships in Cape Town. Child rape is perpetuated by myths sustained by witch doctors and indigenous medicine that promote child rape as a cure-all for symptoms ranging from poverty to AIDS. IL has four satellite groups that educate rape and abuse victims and potential victims. It is assumed that girls are potential victims because of their early unawareness that gender is tied to some patterns of behavior. IL trained mass media groups to educate the general public. IL distributes public information materials on how to identify domestic violence and abuse and how to identify potential rapists within households. Materials are distributed to individuals in community programs and in training programs. Child survivors make presentations in playgroups in a nonthreatening way. IL interacts with courts of law, police stations, hospitals, and schools. The group refers 25-35 cases per day. The group is working on setting up private rooms in police stations where rape victims can make confidential complaints without public attention. IL also works to promote the use of alternative strategies for solving family conflicts.

Spectral reflectance properties of carbon-bearing materials

NASA Technical Reports Server (NTRS)

Cloutis, Edward A.; Gaffey, Michael J.; Moslow, Thomas F.

1994-01-01

The 0.3-2.6 micrometers spectral reflectance properties of carbon polymorphs (graphite, carbon black, diamond), carbides (silicon carbide, cementite), and macromolecular organic-bearing materials (coal, coal tar extract, oil sand, oil shale) are found to vary from sample to sample and among groups. The carbon polymorphs are readily distinguishable on the basis of their visible-near infrared spectral slopes and shapes. The spectra of macromolecular organic-bearing materials show increases in reflectance toward longer wavelengths, exceeding the reflectance rise of more carbon-rich materials. Reflectance spectra of carbonaceous materials are affected by the crystal structure, composition, and degree of order/disorder of the samples. The characteristic spectral properties can potentially be exploited to identify individual carbonaceous grains in meteorites (as separates or in situ) or to conduct remote sensing geothermometry and identification of carbonaceous phases on asteroids.

From the promotion of biodiversity to the Recovery of organic waste

NASA Astrophysics Data System (ADS)

Jammoukh, Mustapha; Mansouri, Khalifa; Salhi, Bachir

2018-05-01

This article presents an empirical research to classify a new renewable resource material, as opposed to eco-composites, it has been neglected by the materials specialist. This classification is based on the typology of elastic behavior demonstrated by tensile tests. In addition, some identifying criterions of the usefulness of this material were examined. To justify the relevance of this classification, curves from the extension of tests focusing on the virgin material, illustrate significant results of the review. Obtained from waste, having a significant recycling possibilities and potential from renewable resources, bio-mechanically characterized loads will be injected into polymeric materials of different categories. All in the perspective of promoting changes in thermomechanical properties, whether static or dynamic; such as resistance to corrosion, heat, wear… They result in functional changes such as security, relief, coatings and stability…

Laser-accelerated particle beams for stress testing of materials.

PubMed

Barberio, M; Scisciò, M; Vallières, S; Cardelli, F; Chen, S N; Famulari, G; Gangolf, T; Revet, G; Schiavi, A; Senzacqua, M; Antici, P

2018-01-25

Laser-driven particle acceleration, obtained by irradiation of a solid target using an ultra-intense (I > 10 18  W/cm 2 ) short-pulse (duration <1 ps) laser, is a growing field of interest, in particular for its manifold potential applications in different domains. Here, we provide experimental evidence that laser-generated particles, in particular protons, can be used for stress testing materials and are particularly suited for identifying materials to be used in harsh conditions. We show that these laser-generated protons can produce, in a very short time scale, a strong mechanical and thermal damage, that, given the short irradiation time, does not allow for recovery of the material. We confirm this by analyzing changes in the mechanical, optical, electrical, and morphological properties of five materials of interest to be used in harsh conditions.

Using choice architecture to exploit a university Distinct Urban Mine.

PubMed

Pierron, Xavier; Williams, Ian D; Shaw, Peter J; Cleaver, Victoria

2017-10-01

There are widespread concerns regarding the potential future scarcity of ferrous and non-ferrous materials. However, there are already potentially rich reserves of secondary materials via high ownership of Electrical and Electronic Equipment (EEE) in economically-developed nations. Young people are particularly high consumers of EEE, thus university students and campuses may present an opportunity to harness this potential. University Distinct Urban Mines (DUM) may be used to exemplify how potential reserves of secondary metals may be exploited, and could contribute to the transition from a linear to a circular economy. This study aimed to evaluate small household appliances (SHA) DUM from a UK university, with the objectives to identify and quantify student households' SHA ownership, WEEE recycling, stockpiling and discarding habits amongst student households, assess and evaluate the monetary potential of SHA DUM at UK level, and propose methods to exploit DUM for universities in the UK. To this purpose, a quantitative survey was undertaken to measure students' ownership and discarding behaviour with respect to SHA. The amounts of ferrous and non-ferrous materials were then estimated and converted to monetary values from secondary materials market data to appraise the SHA DUM overall value. Thirty-five per cent of SHA are discarded in the general refuse. Broken personal care appliances (PCA) tend to be discarded due to hygiene and small size factors. When in working order, SHA tend to be equally reused, recycled or stockpiled. We conclude that a total of 189 tonnes of ferrous and non-ferrous materials were available via discarding or being stockpiled at the University of Southampton. Extrapolated to UK higher education level, discarded and stockpiled SHA represent a potential worth ∼USD 11 million. To initiate DUM exploitation within Higher Education campuses, we suggest improving users' choice architecture by providing collection methods specific to broken SHA. Copyright © 2017. Published by Elsevier Ltd.

Potential contribution of microbial communities in technical ceramics for the improvement of rheological properties

NASA Astrophysics Data System (ADS)

Moreira, Bernardino; Miller, Ana Z.; Santos, Ricardo; Monteiro, Sílvia; Dias, Diamantino; Neves, Orquídia; Dionísio, Amélia; Saiz-Jimenez, Cesareo

2014-05-01

Several bacterial and fungal species naturally occurring in ceramic raw materials used in construction, such as Aspergillus, Penicillium and Aureobasidium, are known to produce exopolysaccharides (EPS). These polymers excreted by the cells are of widespread occurrence and may confer unique and potentially interesting properties with potential industrial uses, such as viscosity control, gelation, and flocculation, during ceramic manufacturing. In this study, the microbial communities present in clay raw materials were identified by both cultural methods and DNA-based molecular techniques in order to appraise their potential contribution to enhance the performance of technical ceramics through the use of EPS. Mineralogical identification by X- Ray Diffraction (XRD) and Fourier Transform Infrared (FTIR) spectroscopy of the clay raw materials, as well as characterization of rheological properties of ceramic slips were also performed. Microbial EPS production and its introduction into ceramic slips will be then carried out in order to evaluate their effects on the rheological properties of the ceramic slips, powders and conformed bodies. Some positive aspects related to the use of EPS are: reduction of the environmental impact caused by synthetic organic additives, reduction of production costs, as well as the costs related with operator protection systems, gaseous effluent treatments, complex landfill, among others.

A Multi-Parametric Device with Innovative Solid Electrodes for Long-Term Monitoring of pH, Redox-Potential and Conductivity in a Nuclear Waste Repository

PubMed Central

Daoudi, Jordan; Betelu, Stephanie; Tzedakis, Theodore; Bertrand, Johan; Ignatiadis, Ioannis

2017-01-01

We present an innovative electrochemical probe for the monitoring of pH, redox potential and conductivity in near-field rocks of deep geological radioactive waste repositories. The probe is composed of a monocrystalline antimony electrode for pH sensing, four AgCl/Ag-based reference or Cl− selective electrodes, one Ag2S/Ag-based reference or S2− selective electrode, as well as four platinum electrodes, a gold electrode and a glassy-carbon electrode for redox potential measurements. Galvanostatic electrochemistry impedance spectroscopy using AgCl/Ag-based and platinum electrodes measure conductivity. The use of such a multi-parameter probe provides redundant information, based as it is on the simultaneous behaviour under identical conditions of different electrodes of the same material, as well as on that of electrodes made of different materials. This identifies the changes in physical and chemical parameters in a solution, as well as the redox reactions controlling the measured potential, both in the solution and/or at the electrode/solution interface. Understanding the electrochemical behaviour of selected materials thus is a key point of our research, as provides the basis for constructing the abacuses needed for developing robust and reliable field sensors. PMID:28608820

A Multi-Parametric Device with Innovative Solid Electrodes for Long-Term Monitoring of pH, Redox-Potential and Conductivity in a Nuclear Waste Repository.

PubMed

Daoudi, Jordan; Betelu, Stephanie; Tzedakis, Theodore; Bertrand, Johan; Ignatiadis, Ioannis

2017-06-13

We present an innovative electrochemical probe for the monitoring of pH, redox potential and conductivity in near-field rocks of deep geological radioactive waste repositories. The probe is composed of a monocrystalline antimony electrode for pH sensing, four AgCl/Ag-based reference or Cl - selective electrodes, one Ag₂S/Ag-based reference or S 2- selective electrode, as well as four platinum electrodes, a gold electrode and a glassy-carbon electrode for redox potential measurements. Galvanostatic electrochemistry impedance spectroscopy using AgCl/Ag-based and platinum electrodes measure conductivity. The use of such a multi-parameter probe provides redundant information, based as it is on the simultaneous behaviour under identical conditions of different electrodes of the same material, as well as on that of electrodes made of different materials. This identifies the changes in physical and chemical parameters in a solution, as well as the redox reactions controlling the measured potential, both in the solution and/or at the electrode/solution interface. Understanding the electrochemical behaviour of selected materials thus is a key point of our research, as provides the basis for constructing the abacuses needed for developing robust and reliable field sensors.

The Material Properties of CsSnBr3 and CsBr:Sn-1% and Their Potential as Scintillator Detector Material

DTIC Science & Technology

2010-03-01

Iodide or Cesium Iodide are the benchmarks for ease of use and quick identification of isotope species. This research aims to explore Cesium Bromide doped...oxidation states of 3+, 4+, 5+ and 6+ were used to identify the Pu pollution in the Rocky Flats area. The identification of the Pu4+ oxidation state...point was causing the normalization of the spectra to be much higher than what it should be. The XANES structures lineup showing the Sn in the CsSnBr3

A systematic typology for negative Poisson's ratio materials and the prediction of complete auxeticity in pure silica zeolite JST.

PubMed

Siddorn, M; Coudert, F-X; Evans, K E; Marmier, A

2015-07-21

Single crystals can commonly have negative Poisson's ratio in a few directions; however more generalised auxeticity is rarer. We propose a typology to distinguish auxetic materials. We characterise numerous single crystals and demonstrate that partial auxeticity occurs for around 37%. We find average auxeticity to be limited to α-cristobalite and no example of complete auxeticity. We simulate two hundreds pure silica zeolites with empirical potentials and quantum chemistry methods, and for the first time identify complete auxeticity in a zeolite network, JST.

Progress in doping of ruthenium silicide (Ru2Si3)

NASA Technical Reports Server (NTRS)

Vining, C. B.; Allevato, C. E.

1992-01-01

Ruthenium silicide is currently under development as a promising thermoelectric material suitable for space power applications. Key to realizing the potentially high figure of merit values of this material is the development of appropriate doping techniques. In this study, manganese and iridium have been identified as useful p- and n-type dopants, respectively. Resistivity values have been reduced by more than 3 orders of magnitude. Anomalous Hall effect results, however, complicate interpretation of some of the results and further effort is required to achieve optimum doping levels.

Evaluation of potential emission spectra for the reliable classification of fluorescently coded materials

NASA Astrophysics Data System (ADS)

Brunner, Siegfried; Kargel, Christian

2011-06-01

The conservation and efficient use of natural and especially strategic resources like oil and water have become global issues, which increasingly initiate environmental and political activities for comprehensive recycling programs. To effectively reutilize oil-based materials necessary in many industrial fields (e.g. chemical and pharmaceutical industry, automotive, packaging), appropriate methods for a fast and highly reliable automated material identification are required. One non-contacting, color- and shape-independent new technique that eliminates the shortcomings of existing methods is to label materials like plastics with certain combinations of fluorescent markers ("optical codes", "optical fingerprints") incorporated during manufacture. Since time-resolved measurements are complex (and expensive), fluorescent markers must be designed that possess unique spectral signatures. The number of identifiable materials increases with the number of fluorescent markers that can be reliably distinguished within the limited wavelength band available. In this article we shall investigate the reliable detection and classification of fluorescent markers with specific fluorescence emission spectra. These simulated spectra are modeled based on realistic fluorescence spectra acquired from material samples using a modern VNIR spectral imaging system. In order to maximize the number of materials that can be reliably identified, we evaluate the performance of 8 classification algorithms based on different spectral similarity measures. The results help guide the design of appropriate fluorescent markers, optical sensors and the overall measurement system.

Design rules for phase-change materials in data storage applications.

PubMed

Lencer, Dominic; Salinga, Martin; Wuttig, Matthias

2011-05-10

Phase-change materials can rapidly and reversibly be switched between an amorphous and a crystalline phase. Since both phases are characterized by very different optical and electrical properties, these materials can be employed for rewritable optical and electrical data storage. Hence, there are considerable efforts to identify suitable materials, and to optimize them with respect to specific applications. Design rules that can explain why the materials identified so far enable phase-change based devices would hence be very beneficial. This article describes materials that have been successfully employed and dicusses common features regarding both typical structures and bonding mechanisms. It is shown that typical structural motifs and electronic properties can be found in the crystalline state that are indicative for resonant bonding, from which the employed contrast originates. The occurence of resonance is linked to the composition, thus providing a design rule for phase-change materials. This understanding helps to unravel characteristic properties such as electrical and thermal conductivity which are discussed in the subsequent section. Then, turning to the transition kinetics between the phases, the current understanding and modeling of the processes of amorphization and crystallization are discussed. Finally, present approaches for improved high-capacity optical discs and fast non-volatile electrical memories, that hold the potential to succeed present-day's Flash memory, are presented. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Accidents with biological material among undergraduate nursing students in a public Brazilian university.

PubMed

Reis, Renata Karina; Gir, Elucir; Canini, Silvia Rita M S

2004-02-01

During their academic activities, undergraduate nursing students are exposed to contamination by bloodborne pathogens, as well as by others found in body fluids, among which are the Human Immunodeficiency (HIV), Hepatitis B and C viruses. We developed a profile of victimized students, characterizing accidents with biological material occurring among undergraduate nursing students at a public university in São Paulo State, Brazil. We identified the main causes and evaluated the conduct adopted by students and their reactions and thoughts concerning the accidents. Seventy-two accidents were identified, of which 17% involved potentially contaminated biological material. Needles were the predominant cause of accidents. The most frequently involved topographic areas were the fingers. Only five students reported the accidents and sought medical care. Among these, two students were advised to begin prophylactic treatment against HIV infection by means of antiretroviral drugs. It was found that the risk of accidents is underestimated and that strategies such as formal teaching and continual training are necessary in order to make students aware of biosafety measures.

Fluoride salts as phase change materials for thermal energy storage in the temperature range 1000-1400 K

NASA Technical Reports Server (NTRS)

Misra, Ajay K.

1988-01-01

Eutectic compositions and congruently melting intermediate compounds in binary and ternary fluoride salt systems were characterized for potential use as latent heat of fusion phase change materials to store thermal energy in the temperature range 1000-1400 K. The melting points and eutectic compositions for many systems with published phase diagrams were experimentally verified and new eutectic compositions having melting points between 1000 and 1400 K were identified. Heats of fusion of several binary and ternary eutectics and congruently melting compounds were experimentally measured by differential scanning calorimetry. For a few systems in which heats of mixing in the melts have been measured, heats of fusion of the eutectics were calculated from thermodynamic considerations and good agreement was obtained between the measured and calculated values. Several combinations of salts with high heats of fusion per unit mass (greater than 0.7 kJ/g) have been identified for possible use as phase change materials in advanced solar dynamic space power applications.

Process improvement methodologies uncover unexpected gaps in stroke care.

PubMed

Kuner, Anthony D; Schemmel, Andrew J; Pooler, B Dustin; Yu, John-Paul J

2018-01-01

Background The diagnosis and treatment of acute stroke requires timed and coordinated effort across multiple clinical teams. Purpose To analyze the frequency and temporal distribution of emergent stroke evaluations (ESEs) to identify potential contributory workflow factors that may delay the initiation and subsequent evaluation of emergency department stroke patients. Material and Methods A total of 719 sentinel ESEs with concurrent neuroimaging were identified over a 22-month retrospective time period. Frequency data were tabulated and odds ratios calculated. Results Of all ESEs, 5% occur between 01:00 and 07:00. ESEs were most frequent during the late morning and early afternoon hours (10:00-14:00). Unexpectedly, there was a statistically significant decline in the frequency of ESEs that occur at the 14:00 time point. Conclusion Temporal analysis of ESEs in the emergency department allowed us to identify an unexpected decrease in ESEs and through process improvement methodologies (Lean and Six Sigma) and identify potential workflow elements contributing to this observation.

Identification of delamination interface in composite laminates using scattering characteristics of lamb wave: numerical and experimental studies

NASA Astrophysics Data System (ADS)

Singh, Rakesh Kumar; Ramadas, C.; Balachandra Shetty, P.; Satyanarayana, K. G.

2017-04-01

Considering the superior strength properties of polymer based composites over metallic materials, they are being used in primary structures of aircrafts. However, these polymeric materials are much more complex in behaviour due to their structural anisotropy along with existence of different materials unlike in metallic alloys. These pose challenge in flaw detection, residual strength determination and life of a structure with their high susceptibility to impact damage in the form of delaminations/disbonds or cracks. This reduces load-bearing capability and potentially leads to structural failure. With this background, this study presents a method to identify location of delamination interface along thickness of a laminate. Both numerical and experimental studies have been carried out with a view to identify the defect, on propagation, mode conversion and scattering characteristics of fundamental anti-symmetric Lamb mode (Ao) when it passed through a semi-infinite delamination. Further, the reflection and transmission scattering coefficients based on power and amplitude ratios of the scattered waves have been computed. The methodology was applied on numerically simulated delaminations to illustrate the efficacy of the method. Results showed that it could successfully identify delamination interface.

Newborn screening education on the internet: a content analysis of North American newborn screening program websites.

PubMed

Araia, Makda H; Potter, Beth K

2011-09-01

The Internet is a potentially important medium for communication about public health programs including newborn screening. This study explores whether the information available on official newborn screening program websites is consistent with existing guidelines regarding educational content for parents. We conducted a systematic search of the public websites of newborn screening programs in the US and Canada, identifying web pages and downloadable brochures that contained educational information. Two researchers independently reviewed all documents to determine the extent to which they included 14 key recommended educational messages. We identified 85 documents containing educational information on 46 US and 6 Canadian newborn screening program websites. The documents contained from 1 to 14 of the recommended messages. The majority of identified materials emphasized the importance and benefits of screening. The differences between US and Canadian materials were related to the importance of parental involvement in follow-up and issues of consent and storage of blood spots. Our findings are consistent with studies of non-web-based newborn screening education materials. The results emphasize the need for further evaluation of newborn screening education, including internet-based resources, particularly in terms of the impact of particular messages on parental attitudes and behaviors.

A Market-Basket Approach to Predict the Acute Aquatic Toxicity of Munitions and Energetic Materials.

PubMed

Burgoon, Lyle D

2016-06-01

An ongoing challenge in chemical production, including the production of insensitive munitions and energetics, is the ability to make predictions about potential environmental hazards early in the process. To address this challenge, a quantitative structure activity relationship model was developed to predict acute fathead minnow toxicity of insensitive munitions and energetic materials. Computational predictive toxicology models like this one may be used to identify and prioritize environmentally safer materials early in their development. The developed model is based on the Apriori market-basket/frequent itemset mining approach to identify probabilistic prediction rules using chemical atom-pairs and the lethality data for 57 compounds from a fathead minnow acute toxicity assay. Lethality data were discretized into four categories based on the Globally Harmonized System of Classification and Labelling of Chemicals. Apriori identified toxicophores for categories two and three. The model classified 32 of the 57 compounds correctly, with a fivefold cross-validation classification rate of 74 %. A structure-based surrogate approach classified the remaining 25 chemicals correctly at 48 %. This result is unsurprising as these 25 chemicals were fairly unique within the larger set.

A male and female RNA marker to infer sex in forensic analysis.

PubMed

van den Berge, M; Sijen, T

2017-01-01

In forensics, DNA profiling is used for the identification of the donor of a trace, while messenger RNA (mRNA) profiling can be applied to identify the cellular origin such as body fluids or organ tissues. The presence of male cell material can be readily assessed by the incorporation of Y-chromosomal markers in quantitation or STR profiling systems. However, no forensic marker exists to positively identify female cell material; merely the presence of female DNA is deduced from the absence of a Y peak, or unbalanced X-Y signals at the Amelogenin locus or unbalanced response of the total and Y-specific quantifier. The presence of two X-chromosomes in female cells invokes dosage compensation, which is achieved through inactivation of one of the X-chromosomes in females. Since this process involves specific RNA molecules, identification of female cellular material may be possible through RNA profiling. Additionally, male material may be identified through RNAs expressed from the Y-chromosome. RNAs preferentially expressed in either sex were assessed for their potential to act as sex markers in forensic RNA assays. To confirm sex-specificity, body fluids and organ tissues of multiple donors of either sex were tested. Additionally, sensitivity of the markers and the suitability of positively identifying male-female mixtures were assessed and degraded samples were used to assess performance of the markers in forensic settings. The addition of sex-specific markers is of added informative value in any RNA profiling system and both markers were incorporated into existing RNA assays that either target body fluids or organs. These are the first forensic assays that enable positive identification of female cellular material. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Accuracy of a Mobile App to Identify Suspect Asbestos-Containing Material in Australian Residential Settings.

PubMed

Govorko, Matthew H; Fritschi, Lin; Reid, Alison

2018-05-14

In situ asbestos in the built environment is a remaining source of exposure in countries that have prohibited the manufacture and use of asbestos. However, it is difficult to identify in situ asbestos-containing material in residential settings. The objective of this study was to evaluate the accuracy of the mobile phone application ("app"), ACM Check, in identifying in situ asbestos located inside and outside of homes compared with onsite inspections conducted by an experienced environmental consultant. A cross-sectional study was undertaken that involved participants completing ACM Check on their homes built pre-1990 and located throughout metropolitan Perth, Western Australia, and an onsite inspection conducted at each home by an environmental consultant. Cohen's kappa statistic was calculated to evaluate the strength of agreement between the two methods. The 40 houses sampled were built between 1898 and 1988 with a median year of 1966. Thirty eight (95%) homes had at least one type of material categorized as positive for asbestos by both ACM Check and the environmental consultant (κ = 1.00). Agreement between the two methods differed when categorizing specific materials as positive or negative for asbestos with substantial agreement for fencing (κ = 0.918), outbuilding walls (κ = 0.844), backing board to electrical meter box (κ = 0.826), exterior wall cladding (κ = 0.771), and interior walls (κ = 0.754), and fair agreement for outbuilding roofs (κ = 0.375), and interior flooring (κ = 0.304). ACM Check is a tool that can be used by tradespeople, home renovators, and householders to screen residential settings for the presence of in situ asbestos-containing material. Mobile phone apps have the potential to be developed or modified for use in other countries to help users identify asbestos and reduce their risk of asbestos exposure.

LDEF materials overview

NASA Technical Reports Server (NTRS)

Stein, Bland A.

1993-01-01

The flight and retrieval of the National Aeronautics and Space Administration's Long Duration Exposure Facility (LDEF) provided an opportunity for the study of the low-Earth orbit (LEO) environment and long-duration space environmental effects (SEE) on materials that is unparalleled in the history of the U.S. Space Program. The 5-year, 9-month flight of LDEF greatly enhanced the potential value of all materials on LDEF to the international SEE community, compared to that of the original 1-year flight plan. The remarkable flight attitude stability of LDEF enables specific analyses of individual and combined effects of LEO environmental parameters on identical materials on the same space vehicle. NASA recognized this potential by forming the LDEF Space Environmental Effects on Materials Special Investigation Group (MSIG) to address the greatly expanded materials and LEO space environment analysis opportunities available in the LDEF structure, experiment trays, and corollary measurements so that the combined value of all LDEF materials data to current and future space missions will be addressed and documented. An overview of the interim LDEF materials findings of the principal investigators and the Materials Special Investigation Group is provided. These revelations are based on observations of LEO environmental effects on materials made in space during LDEF retrieval and during LDEF tray deintegration at the Kennedy Space Center, and on findings of approximately 1.5 years of laboratory analyses of LDEF materials by the LDEF materials scientists. These findings were extensively reviewed and discussed at the MSIG-sponsored LDEF Materials Workshop '91. The results are presented in a format that categorizes the revelations as 'clear findings' or 'obscure preliminary findings' (and progress toward their resolution), plus resultant needs for new space materials developments and ground simulation testing/analytical modeling, in seven categories: materials/environmental parameters and data bases; LDEF contamination; thermal control coatings and protective treatments; polymers and films; polymer-matrix composites; metals, ceramics, and optical materials; and systems-related materials. The utilization of LDEF materials data for future low-Earth orbit missions is also discussed, concentrating on Space Station Freedom. In general, the LDEF data is remarkably consistent; LDEF will provide a 'benchmark' for materials design data bases for satellites in low-Earth orbit. Some materials were identified to be encouragingly resistant to LEO SEE for 5.8-years; other 'space qualified' materials displayed significant environmental degradation. General contamination levels on LDEF were low, but molecular contamination was widespread; LDEF offers an unprecedented opportunity to provide a unified perspective of unmanned LEO spacecraft contamination mechanisms. New material development requirements for long-term LEO missions were identified and current ground simulation testing methods/data for new, durable materials concepts can be validated with LDEF results. LDEF findings are already being integrated into the design of Space Station Freedom.

ALON® Components With Tunable Dielectric Properties for High Power Accelerator Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goldman, Lee M; Jha, Santosh K; Lobur, Nicole

There are challenges in linear particle accelerators associated with the need to suppress “higher order modes” (HOMs). HOMs are detrimental to accelerator operation as they are a source of beam instability. The absorption/suppression of HOMs and dissipation of the energy of higher order modes is vital to the function of these accelerators. Surmet has identified ALON® Optical Ceramic (Aluminum Oxynitride), a hard, durable ceramic that is fabricated through conventional powder processing techniques, as a potential material for HOM absorber. In this Phase I program, Surmet has produced new ALON-composite HOM absorber materials that function at both ambient and cryogenic temperatures.more » The composite materials were developed and evaluated in collaboration with Thomas Jefferson National Labs. Success in this Phase I and the potential Phase II will demonstrate the utility of ALON composite components for RF absorbing applications and lay the groundwork for commercialization of such products, with applications in basic science, medical and digital electronics industries.« less

Progress in the development of advanced solar reflectors

NASA Astrophysics Data System (ADS)

Kennedy, C.; Jorgensen, G.

1994-01-01

Solar thermal technologies require large mirrors to provide concentrated sunlight for renewable power generation. Such materials must be inexpensive and maintain high specular reflectance for extended lifetimes in severe outdoor environments. Polymer reflectors are lighter than glass mirrors, offer greater system design flexibility, and have the potential for lower cost. During the past year, collaborative cost-shared research and development between the National Renewable Energy Laboratory (NREL) and industrial partners has identified candidate materials that perform better than the state-of-the-art commercial silvered-polymer reflectors in terms of corrosion degradation and resistance to delamination failure. Additional cooperative efforts will produce new alternative materials with reduced costs due to high speed production line capability. NREL welcomes continued and expanded interest and web coating industry involvement in developing advanced solar reflector materials.

Extreme ultraviolet resist materials for sub-7 nm patterning.

PubMed

Li, Li; Liu, Xuan; Pal, Shyam; Wang, Shulan; Ober, Christopher K; Giannelis, Emmanuel P

2017-08-14

Continuous ongoing development of dense integrated circuits requires significant advancements in nanoscale patterning technology. As a key process in semiconductor high volume manufacturing (HVM), high resolution lithography is crucial in keeping with Moore's law. Currently, lithography technology for the sub-7 nm node and beyond has been actively investigated approaching atomic level patterning. EUV technology is now considered to be a potential alternative to HVM for replacing in some cases ArF immersion technology combined with multi-patterning. Development of innovative resist materials will be required to improve advanced fabrication strategies. In this article, advancements in novel resist materials are reviewed to identify design criteria for establishment of a next generation resist platform. Development strategies and the challenges in next generation resist materials are summarized and discussed.

Neutron Spectrometry for Identification of filler material in UXO - Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bliss, Mary

2007-09-12

Unexploded ordnance (UXO)-contaminated sites often include ordnance filled with inert substances that were used in dummy rounds. During UXO surveys, it is difficult to determine whether ordnance is filled with explosives or inert material (e.g., concrete, plaster-of-paris, wax, etc.) or is empty. Without verification of the filler material, handling procedures often necessitate that the object be blown in place, which has potential impacts to the environment, personnel, communities and survey costs. The Department of Defense (DoD) needs a reliable, timely, non-intrusive and cost-effective way to identify filler material before a removal action. A new technology that serves this purpose wouldmore » minimize environmental impacts, personnel safety risks and removal costs; and, thus, would be especially beneficial to remediation activities.« less

Functional materials from cellulose-derived liquid-crystal templates.

PubMed

Giese, Michael; Blusch, Lina K; Khan, Mostofa K; MacLachlan, Mark J

2015-03-02

Cellulose nanocrystals (CNCs), known for more than 50 years, have attracted attention because of their unique properties such as high specific strength and modulus, high surface area, and fascinating optical properties. Just recently, however, their potential in supramolecular templating was identified by making use of their self-assembly behavior in aqueous dispersions in the presence of compatible precursors. The combination of the mesoporosity, photonic properties, and chiral nematic order of the materials, which are available as freestanding films, has led to a significant number of interesting and promising discoveries towards new functional materials. This Review summarizes the use of cellulose derivatives, especially CNCs, as novel templates and gives an overview of the recent developments toward new functional materials. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The Challenges of Plasma Material Interactions in Nuclear Fusion Devices and Potential Solutions

DOE PAGES

Rapp, J.

2017-07-12

Plasma Material Interactions in future fusion reactors have been identified as a knowledge gap to be dealt with before any next step device past ITER can be built. The challenges are manifold. They are related to power dissipation so that the heat fluxes to the plasma facing components can be kept at technologically feasible levels; maximization of the lifetime of divertor plasma facing components that allow for steady-state operation in a reactor to reach the neutron fluences required; the tritium inventory (storage) in the plasma facing components, which can lead to potential safety concerns and reduction in the fuel efficiency;more » and it is related to the technology of the plasma facing components itself, which should demonstrate structural integrity under the high temperatures and neutron fluence. This contribution will give an overview and summary of those challenges together with some discussion of potential solutions. New linear plasma devices are needed to investigate the PMI under fusion reactor conditions and test novel plasma facing components. The Material Plasma Exposure eXperiment MPEX will be introduced and a status of the current R&D towards MPEX will be summarized.« less

The Challenges of Plasma Material Interactions in Nuclear Fusion Devices and Potential Solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rapp, J.

Plasma Material Interactions in future fusion reactors have been identified as a knowledge gap to be dealt with before any next step device past ITER can be built. The challenges are manifold. They are related to power dissipation so that the heat fluxes to the plasma facing components can be kept at technologically feasible levels; maximization of the lifetime of divertor plasma facing components that allow for steady-state operation in a reactor to reach the neutron fluences required; the tritium inventory (storage) in the plasma facing components, which can lead to potential safety concerns and reduction in the fuel efficiency;more » and it is related to the technology of the plasma facing components itself, which should demonstrate structural integrity under the high temperatures and neutron fluence. This contribution will give an overview and summary of those challenges together with some discussion of potential solutions. New linear plasma devices are needed to investigate the PMI under fusion reactor conditions and test novel plasma facing components. The Material Plasma Exposure eXperiment MPEX will be introduced and a status of the current R&D towards MPEX will be summarized.« less

Potential Biomolecules and Current Treatment Technologies for Diabetic Foot Ulcer: an Overview.

PubMed

Khashim, Zenith; Samuel, Shila; Duraisamy, Nallusamy; Krishnan, Kathiravan

2017-05-18

Diabetic foot ulceration remains a major challenge and is one of the most expensive and leading causes of major and minor amputations among patients with diabetic foot ulcer. Hence the purpose of this review is to emphasize on potential molecular markers involved in diabetic foot ulcer physiology, the efficacy of different types of dressing materials, adjunct therapy and newer therapeutic approach like nanoparticles for the treatment of diabetic foot ulcer. We conducted a systematic literature review search by using Pubmed and other web searches. The quality evidence of diabetic foot ulcer biomolecules and treatments was collected, summarized and compared with other studies. The present investigation suggested that impaired wound healing in diabetic patients is an influence of several factors. All the advanced therapies and foot ulcer dressing materials are not suitable for all types of diabetic foot ulcers, however more prospective follow ups and in vivo and in vitro studies are needed to draw certain conclusion. Several critical wound biomolecules have been identified and are in need to be investigated in diabetic foot ulcers. The application of biocompatible nanoparticles holds a promising approach for designing dressing materials for the treatment of diabetic foot ulcer. Understanding the cellular and molecular events and identifying the appropriate treatment strategies for different foot ulcer grades will reduce recurrence of foot ulcer and lower limb amputation. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

78 FR 65938 - Endangered and Threatened Wildlife and Plants; 12-Month Finding on a Petition and Proposed Rule...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-04

... support towhees and their habitat. Further, the number of water diversions at towhee-occupied sites has... vehicle (OHV) use), water diversion, and mining. Potential threats identified since listing include energy.... Comments and materials we receive, as well as supporting documentation we used in preparing this proposed...

Georgia Long-Term Pavement Performance (GALTPP) Program – Maintaining Georgia’s Calibration Sites and Identifying the Potential for Using MEPDG for Characterization of Non-Standard Materials and Methods (Phase 1)

DOT National Transportation Integrated Search

2016-10-01

The Georgia Department of Transportation (GDOT) has initiated a Georgia Long-Term Pavement Performance (GALTPP) monitoring program 1) to provide data for calibrating the prediction models in the AASHTO Mechanistic-Empirical Pavement Design Guide (MEP...

NREL Research Identifies Increased Potential for Perovskites as a Material

Science.gov Websites

reducing the amount of energy lost to heat. A paper on the discovery, "Observation of a hot-phonon heat and the rest lost to other processes instead of being converted to electricity. The NREL research where phonons (heat carrying particles) that are emitted while the charge carriers cool cannot decay

Third Party Payments: Alternative Funding Sources for Drug Abuse Treatment Programs. Trainer's Manual and Trainee's Handbook.

ERIC Educational Resources Information Center

Priesman, Ira

This set of materials is designed to provide helping professionals with sufficient understanding of third-party payment systems so they are able to determine the feasibility of obtaining reimbursement for service, identify potential third-party payers, assess implications of introducing a third-party payments system, and develop a plan for…

Prevalence and Potential Factors Associated with Overweight and Obesity Status in Adults with Intellectual Developmental Disorders

ERIC Educational Resources Information Center

Ranjan, Sobhana; Nasser, Jennifer A.; Fisher, Kathleen

2018-01-01

Background: The prevalence of being overweight and obese is increasing not just in the general population but also in individuals with intellectual disability (ID). Therefore, a need to identify factors contributing to overweight/obesity arises as this population is escalating. Materials and Methods: This narrative review article summarizes…

The Sequence of Study Changes What Information Is Attended to, Encoded, and Remembered during Category Learning

ERIC Educational Resources Information Center

Carvalho, Paulo F.; Goldstone, Robert L.

2017-01-01

The sequence of study influences how we learn. Previous research has identified different sequences as potentially beneficial for learning in different contexts and with different materials. Here we investigate the mechanisms involved in inductive category learning that give rise to these sequencing effects. Across 3 experiments we show evidence…

e-Biologics: Fabrication of Sustainable Electronics with “Green” Biological Materials

PubMed Central

2017-01-01

ABSTRACT The growing ubiquity of electronic devices is increasingly consuming substantial energy and rare resources for materials fabrication, as well as creating expansive volumes of toxic waste. This is not sustainable. Electronic biological materials (e-biologics) that are produced with microbes, or designed with microbial components as the guide for synthesis, are a potential green solution. Some e-biologics can be fabricated from renewable feedstocks with relatively low energy inputs, often while avoiding the harsh chemicals used for synthesizing more traditional electronic materials. Several are completely free of toxic components, can be readily recycled, and offer unique features not found in traditional electronic materials in terms of size, performance, and opportunities for diverse functionalization. An appropriate investment in the concerted multidisciplinary collaborative research required to identify and characterize e-biologics and to engineer materials and devices based on e-biologics could be rewarded with a new “green age” of sustainable electronic materials and devices. PMID:28655820

Space shuttle seal material and design development for earth storable propellant systems

NASA Technical Reports Server (NTRS)

1973-01-01

The results of a program to investigate and characterize seal materials suitable for space shuttle storable propellant systems are given. Two new elastomeric materials were identified as being potentially superior to existing state-of-the art materials for specific sealing applications. These materials were AF-E-124D and AF-E-411. AF-E-124D is a cured perfluorinated polymer suitable for use with dinitrogen tetroxide oxidizer, and hydrazine base fuels. AF-E-411 is an ethylene propylene terpolymer material for hydrazine base fuel service. Data are presented relative to low and high temperature characteristics as well as propellant exposure effects. Types of data included are: mechanical properties, stress strain curves, friction and wear characteristics, compression set and permeability. Sealing tests with a flat poppet-seal valve were conducted for verification of sealing capability. A bibliography includes over 200 references relating to seal design or materials and presents a concise tabulation of the more useful seal design data sources.

Quantification of pore clogging characteristics in potential permeable reactive barrier (PRB) substrates using image analysis.

PubMed

Wantanaphong, J; Mooney, S J; Bailey, E H

2006-08-10

Permeable reactive barriers (PRBs) are now an established approach for groundwater remediation. However, one concern is the deterioration of barrier material performance due to pore clogging. This study sought to quantify the effect of pore clogging on the alteration of the physical porous architecture of two novel potential PRB materials (clinoptilolite and calcified seaweed) using image analysis of SEM-derived images. Results after a water treatment contaminated with heavy metals over periods of up to 10 months identified a decrease in porosity from c. 22% to c. 15% for calcified seaweed and from c. 22% to c. 18% for clinoptilolite. Porosity was reduced by as much as 37% in a calcified seaweed column that clogged. The mean pore size (2D) of both materials slightly decreased after water treatment with c. 11% reduction in calcified seaweed and c. 7% reduction in clinoptilolite. An increase in the proportion of crack-shaped pores was observed in both materials after the contaminated water treatment, most noticeably in the bottom of columns where contaminated water first reacted with the material. The distribution of pores (within a given image) derived from the distance transform indicated the largest morphological differences in materials was recorded in calcified seaweed columns, which is likely to impact significantly on their performance as barrier materials. The magnitude of porosity reduction over a short time period in relation to predicted barrier longevity suggest these and similar materials may be unsuited for barrier installation in their present form.

μ SR Investigation of Superconducting PbTaSe2

NASA Astrophysics Data System (ADS)

Wilson, Murray; Hallas, Alannah; Cai, Yipeng; Guo, Shengli; Gong, Zizhou; Ali, Mazhar; Cava, Robert; Uemura, Yasutomo; Luke, Graeme

Noncentrosymmetric superconductors are a topic of considerable interest in the condensed matter physics community. These materials have the potential to exhibit exotic superconducting states, particularly in the presence of strong spin orbit coupling. PbTaSe2 is a noncentrosymmetric material which has very strong spin orbit coupling, and is superconducting with a TC of 3.6 K. Previous studies of this material have identified exotic properties such as Dirac cones gapped by spin-orbit coupling, a topological semi-metal state, and possible multi-band superconductivity. To further explore this material, it is of considerable interest to investigate the pairing symmetry of the superconducting state, and determine whether odd-parity superconductivity may exist. In this talk we will present a μSR investigation of the penetration depth temperature dependece to infer the pairing symmetry. We will also present zero field μSR measurements which suggest that this material has an even-parity superconducting state.

Holographic Recording Materials Development

NASA Technical Reports Server (NTRS)

Verber, C. M.; Schwerzel, R. E.; Perry, P. J.; Craig, R. A.

1976-01-01

Organic photorefractive materials were evaluated for application in a reversible holographic memory system. Representative indigo and thioindigo derivatives and several stilbene derivatives were studied as well as 15, 16-dialkyldihydropyrene derivatives the following goals were achieved: (1) the successful writing of phase holograms in a thioindigo/polymer gel system, (2) the successful writing and erasing of phase holograms in a variety of indigo/polymer gel and indigo/solid polymer systems, and (3) the identification of indigoid dyes and 15, 16-dialkyldihydropyrene derivatives as materials potentially suitable for utilization in an operational system. Photochemical studies of the stilbene, indigo, thioindigo, and dialkyldihydropyrene derivatives in solution and in a variety of polymer matrix materials were conducted with the goal of optimizing the photorefractive behavior of the chemical system as a whole. The spectroscopic properties required of optimal photorefractive materials were identified, and it was shown that both the indigoid dyes and the dialkyldihydropyrenes closely match the required properties.

Natural and technologic hazardous material releases during and after natural disasters: a review.

PubMed

Young, Stacy; Balluz, Lina; Malilay, Josephine

2004-04-25

Natural disasters may be powerful and prominent mechanisms of direct and indirect hazardous material (hazmat) releases. Hazardous materials that are released as the result of a technologic malfunction precipitated by a natural event are referred to as natural-technologic or na-tech events. Na-tech events pose unique environmental and human hazards. Disaster-associated hazardous material releases are of concern, given increases in population density and accelerating industrial development in areas subject to natural disasters. These trends increase the probability of catastrophic future disasters and the potential for mass human exposure to hazardous materials released during disasters. This systematic review summarizes direct and indirect disaster-associated releases, as well as environmental contamination and adverse human health effects that have resulted from natural disaster-related hazmat incidents. Thorough examination of historic disaster-related hazmat releases can be used to identify future threats and improve mitigation and prevention efforts.

Student decisions about lecture attendance: do electronic course materials matter?

PubMed

Billings-Gagliardi, Susan; Mazor, Kathleen M

2007-10-01

This study explored whether first-year medical students make deliberate decisions about attending nonrequired lectures. If so, it sought to identify factors that influence these decisions, specifically addressing the potential impact of electronic materials. Medical students who completed first-year studies between 2004 and 2006 responded to an open-ended survey question about their own lecture-attendance decisions. Responses were coded to capture major themes. Students' ratings of the electronic materials were also examined. Most respondents made deliberate attendance decisions. Decisions were influenced by previous experiences with the lecturer, predictions of what would occur during the session itself, personal learning preferences, and learning needs at that particular time, with the overriding goal of maximizing learning. Access to electronic materials did not influence students' choices. Fears that the increasing availability of technology-enhanced educational materials has a negative impact on lecture attendance seem unfounded.

Structuring of material parameters in lithium niobate crystals with low-mass, high-energy ion radiation

NASA Astrophysics Data System (ADS)

Peithmann, K.; Eversheim, P.-D.; Goetze, J.; Haaks, M.; Hattermann, H.; Haubrich, S.; Hinterberger, F.; Jentjens, L.; Mader, W.; Raeth, N. L.; Schmid, H.; Zamani-Meymian, M.-R.; Maier, K.

2011-10-01

Ferroelectric lithium niobate crystals offer a great potential for applications in modern optics. To provide powerful optical components, tailoring of key material parameters, especially of the refractive index n and the ferroelectric domain landscape, is required. Irradiation of lithium niobate crystals with accelerated ions causes strong structured modifications in the material. The effects induced by low-mass, high-energy ions (such as 3He with 41 MeV, which are not implanted, but transmit through the entire crystal volume) are reviewed. Irradiation yields large changes of the refractive index Δn, improved domain engineering capability within the material along the ion track, and waveguiding structures. The periodic modification of Δn as well as the formation of periodically poled lithium niobate (PPLN) (supported by radiation damage) is described. Two-step knock-on displacement processes, 3He→Nb and 3He→O causing thermal spikes, are identified as origin for the material modifications.

Correlation Between Bulk Material Defects and Spectroscopic Response in Cadmium Zinc Telluride Detectors

NASA Technical Reports Server (NTRS)

Parker, Bradford H.; Stahle, C. M.; Barthelmy, S. D.; Parsons, A. M.; Tueller, J.; VanSant, J. T.; Munoz, B. F.; Snodgrass, S. J.; Mullinix, R. E.

1999-01-01

One of the critical challenges for large area cadmium zinc telluride (CdZnTe) detector arrays is obtaining material capable of uniform imaging and spectroscopic response. Two complementary nondestructive techniques for characterizing bulk CdZnTe have been developed to identify material with a uniform response. The first technique, infrared transmission imaging, allows for rapid visualization of bulk defects. The second technique, x-ray spectral mapping, provides a map of the material spectroscopic response when it is configured as a planar detector. The two techniques have been used to develop a correlation between bulk defect type and detector performance. The correlation allows for the use of infrared imaging to rapidly develop wafer mining maps. The mining of material free of detrimental defects has the potential to dramatically increase the yield and quality of large area CdZnTe detector arrays.

Advances in Nuclear Monitoring Technologies

NASA Astrophysics Data System (ADS)

Park, Brent

2006-03-01

Homeland security requires low-cost, large-area detectors for locating and identifying weapons-usable nuclear materials and monitors for radiological isotopes that are more robust than current systems. Recent advances in electronics materials and nanotechnology, specifically organic semiconductors and inorganic quantum dots, offer potential improvements. We provide an overview of the physical processes involved in radiation detection using these new materials in the design of new device structures. Examples include recent efforts on quantum dots, as well as more traditional radiation-detecting materials such as CdZnTe and high-pressure xenon. Detector improvements demand not only new materials but also enhanced data-analysis tools that reduce false alarms and thus increase the quality of decisions. Additional computing power on hand-held platforms should enable the application of advanced algorithms to radiation-detection problems in the field, reducing the need to transmit data and thus delay analysis.

Evaluation of Quantitative Exposure Assessment Method for Nanomaterials in Mixed Dust Environments: Application in Tire Manufacturing Facilities.

PubMed

Kreider, Marisa L; Cyrs, William D; Tosiano, Melissa A; Panko, Julie M

2015-11-01

Current recommendations for nanomaterial-specific exposure assessment require adaptation in order to be applied to complicated manufacturing settings, where a variety of particle types may contribute to the potential exposure. The purpose of this work was to evaluate a method that would allow for exposure assessment of nanostructured materials by chemical composition and size in a mixed dust setting, using carbon black (CB) and amorphous silica (AS) from tire manufacturing as an example. This method combined air sampling with a low pressure cascade impactor with analysis of elemental composition by size to quantitatively assess potential exposures in the workplace. This method was first pilot-tested in one tire manufacturing facility; air samples were collected with a Dekati Low Pressure Impactor (DLPI) during mixing where either CB or AS were used as the primary filler. Air samples were analyzed via scanning transmission electron microscopy (STEM) coupled with energy dispersive spectroscopy (EDS) to identify what fraction of particles were CB, AS, or 'other'. From this pilot study, it was determined that ~95% of all nanoscale particles were identified as CB or AS. Subsequent samples were collected with the Dekati Electrical Low Pressure Impactor (ELPI) at two tire manufacturing facilities and analyzed using the same methodology to quantify exposure to these materials. This analysis confirmed that CB and AS were the predominant nanoscale particle types in the mixing area at both facilities. Air concentrations of CB and AS ranged from ~8900 to 77600 and 400 to 22200 particles cm(-3), respectively. This method offers the potential to provide quantitative estimates of worker exposure to nanoparticles of specific materials in a mixed dust environment. With pending development of occupational exposure limits for nanomaterials, this methodology will allow occupational health and safety practitioners to estimate worker exposures to specific materials, even in scenarios where many particle types are present. © The Author 2015. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Is Mars Sample Return Required Prior to Sending Humans to Mars?

NASA Technical Reports Server (NTRS)

Carr, Michael; Abell, Paul; Allwood, Abigail; Baker, John; Barnes, Jeff; Bass, Deborah; Beaty, David; Boston, Penny; Brinkerhoff, Will; Budney, Charles;

Bio-Contamination Control for Spacesuit Garments - A Preliminary Study

NASA Technical Reports Server (NTRS)

Rhodes, Richard; Korona, Adam; Orndoff, Evelyn; Ott, Mark; Poritz, Darwin

2010-01-01

This paper outlines a preliminary study to review, test, and improve upon the current state of spacesuit bio-contamination control. The study includes an evaluation of current and advanced suit materials, ground and on-orbit cleaning methods, and microbial test and analysis methods. The first aspect of this study was to identify potential anti-microbial textiles and cleaning agents, and to review current microbial test methods. The anti-microbial cleaning agent and textile market survey included a review of current commercial-off-the-shelf (COTS) products that could potentially be used as future space flight hardware. This review included replacements for any of the softgood layers that may become contaminated during an extravehicular activity (EVA), including the pressure bladder, liquid cooling garment, and ancillary comfort undergarment. After a series of COTS anti-microbial textiles and clean ing agents were identified, a series of four tests were conducted: (1) a stacked configuration test that was conducted in order to review how bio-contamination would propagate through the various suit layers, (2) a individual materials test that evaluated how well each softgood layer either promoted or repressed growth, (3) a cleaning agent test that evaluated the efficacy on each of the baseline bladders, and (4) an evaluation of various COTS anti-microbial textiles. All antimicrobial COTS materials tested appeared to control bacteria colony forming unit (CFU) growth better than the Thermal Comfort Undergarment (TCU) and ACES Liquid Cooling Garment (LCG)/EMU Liquid Cooling Ventilation Garment (LCVG) materials currently in use. However, a comparison of fungi CFU growth in COTS to current suit materials appeared to vary per material. All cleaning agents tested in this study appeared to inhibit the level of bacteria and fungi growth to acceptable levels for short duration tests. While several trends can be obtained from the current analysis, a series of test improvements are described for future microbial testing.

State of the Science Review: Potential for Beneficial Use of ...

EPA Pesticide Factsheets

Metal and metalloid contamination of soil and sediment is a widespread problem both in urban and rural areas throughout the United States (U.S. EPA, 2014). Beneficial use of waste by-products as amendments to remediate metal-contaminated soils and sediments can provide major economic and environmental advantages on both a site-specific and national scale. These waste by-products can also reduce our need to mine virgin materials or produce synthetic materials for amendments. Waste by-products must not be hazardous or pose unacceptable risk to human health and the environment, and should be a suitable replacement for virgin and synthetic materials. This review serves to present the state of science on in-situ remediation of metal-contaminated soil and sediment and the potential for beneficial usage of waste by-product materials. Not all unintended consequences can be fully understood or predicted prior to implementing a treatment option, however some realized, and potentially unrealized, benefits and unintended consequences are explored. The objectives of this review article are to: (1) summarize the current state of the science on in-situ treatment of metal-contaminated soils and sediments; (2) review the more recent use of non-municipal and non-hazardous waste by-products for use as soil and sediment amendments; and (3) identify physical and chemical properties that are indicative of the success or effectiveness of using a specific amendment to treat metal

NEO Targets for Biological In Situ Resource Utilization

NASA Astrophysics Data System (ADS)

Grace, J. M.; Ernst, S. M.; Navarrete, J. U.; Gentry, D.

2014-12-01

We are investigating a mission architecture concept for low-cost pre-processing of materials on long synodic period asteroids using bioengineered microbes delivered by small spacecraft. Space exploration opportunities, particularly those requiring a human presence, are sharply constrained by the high cost of launching resources such as fuel, construction materials, oxygen, water, and foodstuffs. Near-Earth asteroids (NEAs) have been proposed for supporting a human space presence. However, the combination of high initial investment requirements, delayed potential return, and uncertainty in resource payoff currently prevents their effective utilization.Biomining is the process in which microorganisms perform useful material reduction, sequestration or separation. It is commonly used in terrestrial copper extraction. Compared to physical and chemical methods of extraction it is slow, but very low cost, thus rendering economical even very poor ores. These advantages are potentially extensible to asteroid in situ resource utilization (ISRU).One of the first limiting factors for the use of biology in these environments is temperature. A survey of NEA data was conducted to identify those NEAs whose projected interior temperatures remained within both potential (-5 - 100 ºC) and preferred (15 - 45 ºC) ranges for the minimum projected time per synodic period without exceeding 100 ºC at any point. Approximately 2800 of the 11000 NEAs (25%) are predicted to remain within the potential range for at least 90 days, and 120 (1%) in the preferred range.A second major factor is water availability and stability. We have evaluated a design for a small-spacecraft-based injector which forces low-temperature fluid into the NEA interior, creating potentially habitable microniches. The fluid contains microbes genetically engineered to accelerate the degradation rates of a desired fraction of the native resources, allowing for more efficient material extraction upon a subsequent encounter.

Multiple tuning of magnetic biskyrmions using in situ L-TEM in centrosymmetric MnNiGa alloy

NASA Astrophysics Data System (ADS)

Peng, Licong; Zhang, Ying; He, Min; Ding, Bei; Wang, Wenhong; Li, Jianqi; Cai, Jianwang; Wang, Shouguo; Wu, Guangheng; Shen, Baogen

2018-02-01

Magnetic skyrmions are topologically protected spin configurations and have recently received growingly attention in magnetic materials. The existence of biskyrmions within a broad temperature range has been identified in our newly-discovered MnNiGa material, promising for potential application in physics and technological study. Here, the biskyrmion microscopic origination from the spin configuration evolution of stripe ground state is experimentally identified. The biskyrmion manipulations based on the influences of the basic microstructures and external factors such as grain boundary confinement, sample thickness, electric current, magnetic field and temperature have been systematically studied by using real-space Lorentz transmission electron microscopy. These multiple tuning options help to understand the essential properties of MnNiGa and predict a significant step forward for the realization of skyrmion-based spintronic devices.

In vitro chemotaxis and tissue remodeling assays quantitatively characterize foreign body reaction.

PubMed

Jannasch, Maren; Weigel, Tobias; Engelhardt, Lisa; Wiezoreck, Judith; Gaetzner, Sabine; Walles, Heike; Schmitz, Tobias; Hansmann, Jan

2017-01-01

Surgical implantation of a biomaterial triggers foreign-body-induced fibrous encapsulation. Two major mechanisms of this complex physiological process are (I) chemotaxis of fibroblasts from surrounding tissue to the implant region, followed by (II) tissue remodeling. As an alternative to animal studies, we here propose a process-aligned in vitro test platform to investigate the material dependency of fibroblast chemotaxis and tissue remodeling mediated by material-resident macrophages. Embedded in a biomimetic three-dimensional collagen hydrogel, chemotaxis of fibroblasts in the direction of macrophage-material-conditioned cell culture supernatant was analyzed by live cell imaging. A combination of statistical analysis with a complementary parameterized random walk model allowed quantitative and qualitative characterization of the cellular walk process. We thereby identified an increasing macrophage-mediated chemotactic potential ranking of biomaterials from glass over polytetrafluorethylene to titanium. To address long-term effects of bio-material-resident macrophages on fibroblasts in a three-dimensional microenvironment, we further studied tissue remodeling by applying macrophage-material-conditioned medium on fibrous in vitro tissue models. A high correlation of the in vitro tissue model to state of the art in vivo study data was found. Titanium exhibited a significantly lower tissue remodeling capacity compared to polytetrafluorethylene. With this approach, we identified a material dependency of both chemotaxis and tissue remodeling processes, strengthening knowledge on their specific contribution to the foreign body reaction.

Establishing and testing the "reuse potential" indicator for managing wastes as resources.

PubMed

Park, Joo Young; Chertow, Marian R

2014-05-01

This study advances contemporary ideas promoting the importance of managing wastes as resources such as closed-loop or circular material economies, and sustainable materials management by reinforcing the notion of a resource-based paradigm rather than a waste-based one. It features the creation of a quantitative tool, the "reuse potential indicator" to specify how "resource-like" versus how "waste-like" specific materials are on a continuum. Even with increasing attention to waste reuse and resource conservation, constant changes in product composition and complexity have left material managers without adequate guidance to make decisions about what is technically feasible to recover from the discard stream even before markets can be considered. The reuse potential indicator is developed to aid management decision-making about waste based not on perception but more objectively on the technical ability of the materials to be reused in commerce. This new indicator is based on the extent of technological innovation and commercial application of actual reuse approaches identified and cataloged. Coal combustion by-products (CCBs) provide the test case for calculating the reuse potential indicator. While CCBs are often perceived as wastes and then isolated in landfills or surface impoundments, there is also a century-long history in the industry of developing technologies to reuse CCBs. The recent statistics show that most CCBs generated in Europe and Japan are reused (90-95%), but only 40-45% of CCBs are used in the United States. According to the reuse potential calculation, however, CCBs in the United States have high technical reusability. Of the four CCBs examined under three different regulatory schemes, reuse potential for boiler slag and flue-gas desulfurization gypsum maintains a value greater than 0.8 on a 0-1 scale, indicating they are at least 80% resource-like. Under current regulation in the United States, both fly ash and bottom ash are 80-90% resource-like. Very strict regulation would remove many reuse options decreasing potential for these two CCBs to 30% resource-like. A more holistic view of waste and broad application of the new indicator would make clear what technologies are available and assist public and private decision makers in setting quantitative material reuse targets from a new knowledge base that reinforces a resource-based paradigm. Copyright © 2014 Elsevier Ltd. All rights reserved.

Military wastes-to-energy applications

NASA Astrophysics Data System (ADS)

Kawaoka, K. E.

1980-11-01

This analysis focuses on the military waste material and byproduct stream and the potential for energy recovery and utilization. Feedstock material includes municipal-type solid waste, selected installation hazardous waste, and biomass residue. The study objectives are to (1) analyze the characteristics of the military waste stream; (2) identify potential energy recovery options; and (3) examine and assess the technical and economic feasibility and environmental and institutional impacts of various energy recovery approaches. Total energy recoverable from DOD solid waste could provide about 2 percent of DOD's facility energy demand. The energy potential available to DOD from biomass and hazardous waste was not available. Available waste-to-energy systems are thermal conversion processes such as incineration with heat recovery. The significance of this recoverable energy from military wastes is put in proper perspective when the benefits and barriers in using waste-derived energy are considered. Some of the benefits of waste-to-energy conversion are as follows: waste energy is a readily available and inexhaustible resource that greatly reduces dependence on imported energy.

Evaluation of Spacecraft Shielding Effectiveness for Radiation Protection

NASA Technical Reports Server (NTRS)

Cucinotta, Francis A.; Wilson, John W.

1999-01-01

The potential for serious health risks from solar particle events (SPE) and galactic cosmic rays (GCR) is a critical issue in the NASA strategic plan for the Human Exploration and Development of Space (HEDS). The excess cost to protect against the GCR and SPE due to current uncertainties in radiation transmission properties and cancer biology could be exceedingly large based on the excess launch costs to shield against uncertainties. The development of advanced shielding concepts is an important risk mitigation area with the potential to significantly reduce risk below conventional mission designs. A key issue in spacecraft material selection is the understanding of nuclear reactions on the transmission properties of materials. High-energy nuclear particles undergo nuclear reactions in passing through materials and tissue altering their composition and producing new radiation types. Spacecraft and planetary habitat designers can utilize radiation transport codes to identify optimal materials for lowering exposures and to optimize spacecraft design to reduce astronaut exposures. To reach these objectives will require providing design engineers with accurate data bases and computationally efficient software for describing the transmission properties of space radiation in materials. Our program will reduce the uncertainty in the transmission properties of space radiation by improving the theoretical description of nuclear reactions and radiation transport, and provide accurate physical descriptions of the track structure of microscopic energy deposition.

Report of sampling and analysis results, Addison Army housing units, Addison, Illinois. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1990-09-01

The objectives of this sampling and analysis effort include further characterization of environmental contamination identified in an enhanced preliminary assessment carried out in 1989. The specific activities performed at this site were identification, evaluation of the condition, and collection of samples from specific suspected asbestos-containing materials, including floor tiles, pipe run and pipe fitting insulation, dust in the ductwork, and exterior siding, where present. These evaluation were necessary to clarify potential environmental issues identified in the earlier report, prior to the sale or realignment of the property.

The Relationship of Bacterial Biofilms and Capsular Contracture in Breast Implants

PubMed Central

Ajdic, Dragana; Zoghbi, Yasmina; Gerth, David; Panthaki, Zubin J.; Thaller, Seth

2016-01-01

Capsular contracture is a common sequelae of implant-based breast augmentation. Despite its prevalence, the etiology of capsular contracture remains controversial. Numerous studies have identified microbial biofilms on various implantable materials, including breast implants. Furthermore, biofilms have been implicated in subclinical infections associated with other surgical implants. In this review, we discuss microbial biofilms as a potential etiology of capsular contracture. The review also outlines the key diagnostic modalities available to identify the possible infectious agents found in biofilm, as well as available preventative and treatment measures. PMID:26843099

Cell attachment properties of Portland cement-based endodontic materials: biological and methodological considerations.

PubMed

Ahmed, Hany Mohamed Aly; Luddin, Norhayati; Kannan, Thirumulu Ponnuraj; Mokhtar, Khairani Idah; Ahmad, Azlina

2014-10-01

The attachment and spreading of mammalian cells on endodontic biomaterials are an area of active research. The purpose of this review is to discuss the cell attachment properties of Portland cement (PC)-based materials by using scanning electron microscope (SEM). In addition, methodological aspects and technical challenges are discussed. A PubMed electronic search was conducted by using appropriate key words to identify the available investigations on the cell attachment properties of PC-based endodontic materials. After retrieving the full text of related articles, the cross citations were also identified. A total of 23 articles published between January 1993 and October 2013 were identified. This review summarizes the cell attachment properties of commercial and experimental PC-based materials on different cell cultures by using SEM. Methodological procedures, technical challenges, and relevance of SEM in determining the biological profile of PC-based materials are discussed. SEM observations demonstrate that commercial MTA formulations show favorable cell attachment properties, which is consistent with their successful clinical outcomes. The favorable cell attachment properties of PC and its modified formulations support its potential use as a substitute for mineral trioxide aggregate. However, researchers should carefully select cell types for their SEM investigations that would be in contact with the proposed PC-based combinations in the clinical situation. Despite being a technical challenge, SEM provides useful information on the cell attachment properties of PC-based materials; however, other assays for cell proliferation and viability are essential to come up with an accurate in vitro biological profile of any given PC-based formulation. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patil, Vidya, E-mail: vidya.patil@ruparel.edu; Patki, Mugdha, E-mail: mugdha.patki@ruparel.edu

Many nonlinear optical (NLO) crystals have been identified as potential candidates in optical and electro-optical devices. Use of NLO organic crystals is expected in photonic applications. Hence organic nonlinear optical materials have been intensely investigated due to their potentially high nonlinearities, and rapid response in electro-optic effect compared to inorganic NLO materials. There are many methods to grow organic crystals such as vapor growth method, melt growth method and solution growth method. Out of these methods, solution growth method is useful in providing constraint free crystal. Single crystals of Dopamine have been grown by evaporating the solvents from aqueous solution.more » Crystals obtained were of the size of orders of mm. The crystal structure of dopamine was determined using XRD technique. Images of crystals were obtained using FEG SEM Quanta Series under high vacuum and low KV.« less

Paleoenvironment and possibilities of plant exploitation in the Middle Pleistocene of Schöningen (Germany). Insights from botanical macro-remains and pollen.

PubMed

Bigga, Gerlinde; Schoch, Werner H; Urban, Brigitte

2015-12-01

Plant use is an elusive issue in Paleolithic archaeology. Due to poor organic preservation in many sites, botanical material is not always present. The sediments in Schöningen, however, contain abundant botanical macro-remains like wood, fruits, seeds, and other parts of plants which offer the opportunity to reconstruct the local vegetation. Combined with palynological results, it is possible to reveal the full potential of this environment to hominins. Ethnobotanical studies of hunter-gatherer societies living in similar environments illustrate the importance of plants for subsistence purposes. The identified taxa from the archaeological horizons at Schöningen include a broad spectrum of potentially exploitable species that could be sources of food, raw material, and firewood. Copyright © 2015 Elsevier Ltd. All rights reserved.

Technical Needs for Prototypic Prognostic Technique Demonstration for Advanced Small Modular Reactor Passive Components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meyer, Ryan M.; Coble, Jamie B.; Hirt, Evelyn H.

2013-05-17

This report identifies a number of requirements for prognostics health management of passive systems in AdvSMRs, documents technical gaps in establishing a prototypical prognostic methodology for this purpose, and describes a preliminary research plan for addressing these technical gaps. AdvSMRs span multiple concepts; therefore a technology- and design-neutral approach is taken, with the focus being on characteristics that are likely to be common to all or several AdvSMR concepts. An evaluation of available literature is used to identify proposed concepts for AdvSMRs along with likely operational characteristics. Available operating experience of advanced reactors is used in identifying passive components thatmore » may be subject to degradation, materials likely to be used for these components, and potential modes of degradation of these components. This information helps in assessing measurement needs for PHM systems, as well as defining functional requirements of PHM systems. An assessment of current state-of-the-art approaches to measurements, sensors and instrumentation, diagnostics and prognostics is also documented. This state-of-the-art evaluation, combined with the requirements, may be used to identify technical gaps and research needs in the development, evaluation, and deployment of PHM systems for AdvSMRs. A preliminary research plan to address high-priority research needs for the deployment of PHM systems to AdvSMRs is described, with the objective being the demonstration of prototypic prognostics technology for passive components in AdvSMRs. Greater efficiency in achieving this objective can be gained through judicious selection of materials and degradation modes that are relevant to proposed AdvSMR concepts, and for which significant knowledge already exists. These selections were made based on multiple constraints including the analysis performed in this document, ready access to laboratory-scale facilities for materials testing and measurement, and potential synergies with other national laboratory and university partners.« less

Application of ICH Q9 Quality Risk Management Tools for Advanced Development of Hot Melt Coated Multiparticulate Systems.

PubMed

Stocker, Elena; Becker, Karin; Hate, Siddhi; Hohl, Roland; Schiemenz, Wolfgang; Sacher, Stephan; Zimmer, Andreas; Salar-Behzadi, Sharareh

2017-01-01

This study aimed to apply quality risk management based on the The International Conference on Harmonisation guideline Q9 for the early development stage of hot melt coated multiparticulate systems for oral administration. N-acetylcysteine crystals were coated with a formulation composing tripalmitin and polysorbate 65. The critical quality attributes (CQAs) were initially prioritized using failure mode and effects analysis. The CQAs of the coated material were defined as particle size, taste-masking efficiency, and immediate release profile. The hot melt coated process was characterized via a flowchart, based on the identified potential critical process parameters (CPPs) and their impact on the CQAs. These CPPs were prioritized using a process failure mode, effects, and criticality analysis and their critical impact on the CQAs was experimentally confirmed using a statistical design of experiments. Spray rate, atomization air pressure, and air flow rate were identified as CPPs. Coating amount and content of polysorbate 65 in the coating formulation were identified as critical material attributes. A hazard and critical control points analysis was applied to define control strategies at the critical process points. A fault tree analysis evaluated causes for potential process failures. We successfully demonstrated that a standardized quality risk management approach optimizes the product development sustainability and supports the regulatory aspects. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Assessing Unmet Information Needs of Breast Cancer Survivors: Exploratory Study of Online Health Forums Using Text Classification and Retrieval.

PubMed

McRoy, Susan; Rastegar-Mojarad, Majid; Wang, Yanshan; Ruddy, Kathryn J; Haddad, Tufia C; Liu, Hongfang

2018-05-15

Patient education materials given to breast cancer survivors may not be a good fit for their information needs. Needs may change over time, be forgotten, or be misreported, for a variety of reasons. An automated content analysis of survivors' postings to online health forums can identify expressed information needs over a span of time and be repeated regularly at low cost. Identifying these unmet needs can guide improvements to existing education materials and the creation of new resources. The primary goals of this project are to assess the unmet information needs of breast cancer survivors from their own perspectives and to identify gaps between information needs and current education materials. This approach employs computational methods for content modeling and supervised text classification to data from online health forums to identify explicit and implicit requests for health-related information. Potential gaps between needs and education materials are identified using techniques from information retrieval. We provide a new taxonomy for the classification of sentences in online health forum data. 260 postings from two online health forums were selected, yielding 4179 sentences for coding. After annotation of data and training alternative one-versus-others classifiers, a random forest-based approach achieved F1 scores from 66% (Other, dataset2) to 90% (Medical, dataset1) on the primary information types. 136 expressions of need were used to generate queries to indexed education materials. Upon examination of the best two pages retrieved for each query, 12% (17/136) of queries were found to have relevant content by all coders, and 33% (45/136) were judged to have relevant content by at least one. Text from online health forums can be analyzed effectively using automated methods. Our analysis confirms that breast cancer survivors have many information needs that are not covered by the written documents they typically receive, as our results suggest that at most a third of breast cancer survivors' questions would be addressed by the materials currently provided to them. ©Susan McRoy, Majid Rastegar-Mojarad, Yanshan Wang, Kathryn J. Ruddy, Tufia C. Haddad, Hongfang Liu. Originally published in JMIR Cancer (http://cancer.jmir.org), 15.05.2018.

Assessing Unmet Information Needs of Breast Cancer Survivors: Exploratory Study of Online Health Forums Using Text Classification and Retrieval

PubMed Central

Rastegar-Mojarad, Majid; Wang, Yanshan; Ruddy, Kathryn J; Haddad, Tufia C; Liu, Hongfang

2018-01-01

Background Patient education materials given to breast cancer survivors may not be a good fit for their information needs. Needs may change over time, be forgotten, or be misreported, for a variety of reasons. An automated content analysis of survivors' postings to online health forums can identify expressed information needs over a span of time and be repeated regularly at low cost. Identifying these unmet needs can guide improvements to existing education materials and the creation of new resources. Objective The primary goals of this project are to assess the unmet information needs of breast cancer survivors from their own perspectives and to identify gaps between information needs and current education materials. Methods This approach employs computational methods for content modeling and supervised text classification to data from online health forums to identify explicit and implicit requests for health-related information. Potential gaps between needs and education materials are identified using techniques from information retrieval. Results We provide a new taxonomy for the classification of sentences in online health forum data. 260 postings from two online health forums were selected, yielding 4179 sentences for coding. After annotation of data and training alternative one-versus-others classifiers, a random forest-based approach achieved F1 scores from 66% (Other, dataset2) to 90% (Medical, dataset1) on the primary information types. 136 expressions of need were used to generate queries to indexed education materials. Upon examination of the best two pages retrieved for each query, 12% (17/136) of queries were found to have relevant content by all coders, and 33% (45/136) were judged to have relevant content by at least one. Conclusions Text from online health forums can be analyzed effectively using automated methods. Our analysis confirms that breast cancer survivors have many information needs that are not covered by the written documents they typically receive, as our results suggest that at most a third of breast cancer survivors’ questions would be addressed by the materials currently provided to them. PMID:29764801

Estrogen Receptor Binding Affinity of Food Contact Material Components Estimated by QSAR.

PubMed

Sosnovcová, Jitka; Rucki, Marián; Bendová, Hana

2016-09-01

The presented work characterized components of food contact materials (FCM) with potential to bind to estrogen receptor (ER) and cause adverse effects in the human organism. The QSAR Toolbox, software application designed to identify and fill toxicological data gaps for chemical hazard assessment, was used. Estrogen receptors are much less of a lock-and-key interaction than highly specific ones. The ER is nonspecific enough to permit binding with a diverse array of chemical structures. There are three primary ER binding subpockets, each with different requirements for hydrogen bonding. More than 900 compounds approved as of FCM components were evaluated for their potential to bind on ER. All evaluated chemicals were subcategorized to five groups with respect to the binding potential to ER: very strong, strong, moderate, weak binder, and no binder to ER. In total 46 compounds were characterized as potential disturbers of estrogen receptor. Among the group of selected chemicals, compounds with high and even very high affinity to the ER binding subpockets were found. These compounds may act as gene activators and cause adverse effects in the organism, particularly during pregnancy and breast-feeding. It should be considered to carry out further in vitro or in vivo tests to confirm their potential to disturb the regulation of physiological processes in humans by abnormal ER signaling and subsequently remove these chemicals from the list of approved food contact materials. Copyright© by the National Institute of Public Health, Prague 2016

Installation Restoration Program. Phase I. Records Search, Hazardous Materials Disposal Sites, Griffiss AFB, New York.

DTIC Science & Technology

1981-07-01

Disposal Methods 4-31 Evaluation of Past and Present Waste 4-35 Disposal Facilities Landfills 4-35 Dry Wells 4-37 Rating of Waste Disposal Sites 4-37 V 2...Problems Identified at GAPE Landfills 4-36 4.12 Priority Ranking of Potential 4-38 Contamination Sources 4.13 -4.31 Rating Forms for Waste Disposal Sites 4...39 -4-76 5.1 Priority Ranking of Potential Con- 5-2 tamination Sources B.1 Rating Factor System B-2 -B-5 4W EXECUTIVE SUMMARY The Resource

Materials for Advanced Ultra-supercritical (A-USC) Steam Turbines – A-USC Component Demonstration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Purgert, Robert; Phillips, Jeffrey; Hendrix, Howard

The work by the United States Department of Energy (U.S. DOE)/Ohio Coal Development Office (OCDO) advanced ultra-supercritical (A-USC) Steam Boiler and Turbine Materials Consortia from 2001 through September 2015 was primarily focused on lab scale and pilot scale materials testing. This testing included air- or steam-cooled “loops” that were inserted into existing utility boilers to gain exposure of these materials to realistic conditions of high temperature and corrosion due to the constituents in the coal. Successful research and development resulted in metallic alloy materials and fabrication processes suited for power generation applications with metal temperatures up to approximately 1472°F (800°C).more » These materials or alloys have shown, in extensive laboratory tests and shop fabrication studies, to have excellent applicability for high-efficiency low CO 2 transformational power generation technologies previously mentioned. However, as valuable as these material loops have been for obtaining information, their scale is significantly below that required to minimize the risk associated with a power company building a multi-billion dollar A-USC power plant. To decrease the identified risk barriers to full-scale implementation of these advanced materials, the U.S. DOE/OCDO A-USC Steam Boiler and Turbine Materials Consortia identified the key areas of the technology that need to be tested at a larger scale. Based upon the recommendations and outcome of a Consortia-sponsored workshop with the U.S.’s leading utilities, a Component Test (ComTest) Program for A-USC was proposed. The A-USC ComTest program would define materials performance requirements, plan for overall advanced system integration, design critical component tests, fabricate components for testing from advanced materials, and carry out the tests. The AUSC Component Test was premised on the program occurring at multiple facilities, with the operating temperatures, pressure and/or size of these components determining the optimum test location. The first step of the ComTest, the steam turbine test, was determined best suited for a site in Youngstown, Ohio. Efforts were also undertaken to identify and evaluate other potential sites for high pressure testing.« less

On residual stresses and homeostasis: an elastic theory of functional adaptation in living matter.

PubMed

Ciarletta, P; Destrade, M; Gower, A L

2016-04-26

Living matter can functionally adapt to external physical factors by developing internal tensions, easily revealed by cutting experiments. Nonetheless, residual stresses intrinsically have a complex spatial distribution, and destructive techniques cannot be used to identify a natural stress-free configuration. This work proposes a novel elastic theory of pre-stressed materials. Imposing physical compatibility and symmetry arguments, we define a new class of free energies explicitly depending on the internal stresses. This theory is finally applied to the study of arterial remodelling, proving its potential for the non-destructive determination of the residual tensions within biological materials.

Advances and trends in computational structural mechanics

NASA Technical Reports Server (NTRS)

Noor, A. K.

1986-01-01

Recent developments in computational structural mechanics are reviewed with reference to computational needs for future structures technology, advances in computational models for material behavior, discrete element technology, assessment and control of numerical simulations of structural response, hybrid analysis, and techniques for large-scale optimization. Research areas in computational structural mechanics which have high potential for meeting future technological needs are identified. These include prediction and analysis of the failure of structural components made of new materials, development of computational strategies and solution methodologies for large-scale structural calculations, and assessment of reliability and adaptive improvement of response predictions.

Thermodynamic analysis of chemical compatibility of several compounds with Fe-Cr-Al alloys

NASA Technical Reports Server (NTRS)

Misra, Ajay K.

1993-01-01

Chemical compatibility between Fe-19.8Cr-4.8Al (weight percent), which is the base composition for the commercial superalloy MA956, and several carbides, borides, nitrides, oxides, and silicides was analyzed from thermodynamic considerations. The effect of addition of minor alloying elements, such as Ti, Y, and Y2O3, to the Fe-Cr-Al alloy on chemical compatibility between the alloy and various compounds was also analyzed. Several chemically compatible compounds that can be potential reinforcement materials and/or interface coating materials for Fe-Cr-Al based composites were identified.

Fatigue of titanium alloys in a supersonic-cruise airplane environment

NASA Technical Reports Server (NTRS)

Imig, L. A.

1976-01-01

The test programs conducted by several aerospace companies and NASA, summarized in this paper, studied several titanium materials previously identified as having high potential for application to supersonic cruise airplane structures. These studies demonstrate that the temperature (560 K) by itself produced no significant degradation of the materials. However, the fatigue resistance of titanium-alloy structures, in which thermal and loading effects are combined, has been studied insufficiently. The predominant topic for future study of fatigue problems in Mach 3 structures should be the influences of thermal stress particularly, the effects of thermal stress on failure location.

Relativistic Gurzhi effect in channels of Dirac materials

NASA Astrophysics Data System (ADS)

Kashuba, Oleksiy; Trauzettel, Björn; Molenkamp, Laurens W.

2018-05-01

Charge transport in channel-shaped 2D Dirac systems is studied employing the Boltzmann equation. The dependence of the resistivity on temperature and chemical potential is investigated. An accurate understanding of the influence of electron-electron interaction and material disorder allows us to identify a parameter regime, where the system reveals hydrodynamic transport behavior. We point out the conditions for three Dirac fermion specific features: heat flow hydrodynamics, pseudodiffusive transport, and the electron-hole scattering dominated regime. It is demonstrated that for clean samples the relativistic Gurzhi effect, a definite indicator of hydrodynamic transport, can be observed.

Crystal growth in a low gravity environment

NASA Technical Reports Server (NTRS)

Carruthers, J. R.

1977-01-01

Crystal growth in microgravity possesses several distinct technological advantages over earth-bound processes; containerless handling and reduction of density gradient driven as well as sedimentation flows. Experiments performed in space to date have been basically reproductions of processes currently used on earth and the results have clarified our understanding of crystal growth dynamics. In addition, both unresolved problems and areas requiring further study on earth have been identified. Future work in space processing of materials must address these areas of study as soon as possible if the full potential of a space environment to develop new techniques and materials is to be realized.

Nonassociative plasticity model for cohesionless materials and its implementation in soil-structure interaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hashmi, Q.S.E.

A constitutive model based on rate-independent elastoplasticity concepts is developed and used to simulate the behavior of geologic materials under arbitrary three-dimensional stress paths. The model accounts for various factors such as friction, stress path, and stress history that influence the behavior of geologic materials. A hierarchical approach is adopted whereby models of progressively increasing sophistication are developed from a basic isotropic-hardening associate model. Nonassociativeness is introduced as correction or perturbation to the basic model. Deviation of normality of the plastic-strain increments to the yield surface F is captured through nonassociativeness. The plastic potential Q is obtained by applying amore » correction to F. This simplified approach restricts the number of extra parameters required to define the plastic potential Q. The material constants associated with the model are identified, and they are evaluated for three different sands (Leighton Buzzard, Munich and McCormick Ranch). The model is then verified by comparing predictions with laboratory tests from which the constants were found, and typical tests not used for finding the constants. Based on the above findings, a soil-footing system is analyzed using finite-element techniques.« less

Bringing a Time-Depth Perspective to Collective Animal Behaviour.

PubMed

Biro, Dora; Sasaki, Takao; Portugal, Steven J

2016-07-01

The field of collective animal behaviour examines how relatively simple, local interactions between individuals in groups combine to produce global-level outcomes. Existing mathematical models and empirical work have identified candidate mechanisms for numerous collective phenomena but have typically focused on one-off or short-term performance. We argue that feedback between collective performance and learning - giving the former the capacity to become an adaptive, and potentially cumulative, process - is a currently poorly explored but crucial mechanism in understanding collective systems. We synthesise material ranging from swarm intelligence in social insects through collective movements in vertebrates to collective decision making in animal and human groups, to propose avenues for future research to identify the potential for changes in these systems to accumulate over time. Copyright © 2016 Elsevier Ltd. All rights reserved.

Mycorrhizal inoculum potentials of pure reclamation materials and revegetated tailing sands from the Canadian oil sand industry.

PubMed

Bois, G; Piché, Y; Fung, M Y P; Khasa, D P

2005-05-01

Recent improvements in the management of oil sand tailings used by the Canadian oil sand industry have resulted in the production of composite tailing sands (CT): a new challenging material for reclamation work. Jack pine (Pinus banksiana Lamb.), hybrid poplar (Populus deltoides Bartr. ex Marsh. xPopulus nigra L.) and red clover (Trifolium pratense L.) plants were used in an 8-week greenhouse bioassay to evaluate the mycorrhizal inoculum potential of CT. This inoculum potential was compared with that of three other reclamation materials [common tailing sands (TS), deep overburden (OB) and muskeg peat (MK)], and with three sites reclaimed in 1982 (R82), 1988 (R88) and 1999 (R99). CT was devoid of active mycorrhizal propagules while all other materials showed some level of inoculum potential. Arbuscular mycorrhizal fungi were observed on roots of clover or poplar grown in TS, OB, and all substrates containing peat (MK, R82, R88 and R99). Pine roots were also colonized by vesicle-forming hyphae of an unidentified fine endophyte and by dark septate fungi. Ectomycorrhizas (ECM) were observed on pine and poplar grown in OB, MK, and in soils from the two older reclaimed sites (R82 and R88). Using morpho- and molecular typing, six ECM fungi were identified to the genus or species level: Laccaria sp., Thelephora americana, Wilcoxina sp. (E-strain), Tuber sp. (I-type), a Sebacinoid, and a Pezizales species. Laccaria sp. and Wilcoxina sp. were the most frequently observed ECM species.

Antibacterial Metallic Touch Surfaces

PubMed Central

Villapún, Victor M.; Dover, Lynn G.; Cross, Andrew; González, Sergio

2016-01-01

Our aim is to present a comprehensive review of the development of modern antibacterial metallic materials as touch surfaces in healthcare settings. Initially we compare Japanese, European and US standards for the assessment of antimicrobial activity. The variations in methodologies defined in these standards are highlighted. Our review will also cover the most relevant factors that define the antimicrobial performance of metals, namely, the effect of humidity, material geometry, chemistry, physical properties and oxidation of the material. The state of the art in contact-killing materials will be described. Finally, the effect of cleaning products, including disinfectants, on the antimicrobial performance, either by direct contact or by altering the touch surface chemistry on which the microbes attach, will be discussed. We offer our outlook, identifying research areas that require further development and an overview of potential future directions of this exciting field. PMID:28773856

A Revolution in the Making: Advances in Materials That May Transform Future Exploration Infrastructures and Missions

NASA Technical Reports Server (NTRS)

Harris, Charles E.; Dicus, Dennis L.; Shuart, Mark J.

2001-01-01

The NASA Strategic Plan identifies the long-term goal to provide safe and affordable space access, orbital transfer, and interplanetary transportation capabilities to enable research, human exploration, and the commercial development of space; and to conduct human and robotic missions to planets and other bodies in our solar system. Numerous scientific and engineering breakthroughs will be required to develop the technology necessary to achieve this goal. Critical technologies include advanced vehicle primary and secondary structure, radiation protection, propulsion and power systems, fuel storage, electronics and devices, sensors and science instruments, and medical diagnostics and treatment. Advanced materials with revolutionary new capabilities are an essential element of each of these technologies. This paper discusses those materials best suited for aerospace vehicle structure and highlights the enormous potential of one revolutionary new material, carbon nanotubes.

Using Enviro-Pod low altitude imagery to inventory building surface materials for an acid rain study - A Baltimore example

NASA Technical Reports Server (NTRS)

Ellefsen, Richard; Coffland, Bruce

1987-01-01

Low altitude, oblique and vertical color photography taken from EPA's Enviro-Pod Ka 85 camera system has provided the data for taking an inventory of building surface materials in a test area of downtown Baltimore. Photography was acquired from a gridded flight plan to provide views of all sides of buildings. Color, texture, and linear detail are employed in the photo interpretation aided by contextual reference to a classification of building construction type developed in an earlier study. The work could potentially support a materials inventory initiated by the National Acid Precipitation Assessment Program (NAPAP) by scientists from EPA, Geological Survey, and the Department of Energy. Initial results show the method to be viable. Discrete surface materials such as brick, both bare and painted, stone, and metal are identified.

Ballistic Puncture Self-Healing Polymeric Materials

NASA Technical Reports Server (NTRS)

Gordon, Keith L.; Siochi, Emilie J.; Yost, William T.; Bogert, Phil B.; Howell, Patricia A.; Cramer, K. Elliott; Burke, Eric R.

2017-01-01

Space exploration launch costs on the order of $10,000 per pound provide an incentive to seek ways to reduce structural mass while maintaining structural function to assure safety and reliability. Damage-tolerant structural systems provide a route to avoiding weight penalty while enhancing vehicle safety and reliability. Self-healing polymers capable of spontaneous puncture repair show promise to mitigate potentially catastrophic damage from events such as micrometeoroid penetration. Effective self-repair requires these materials to quickly heal following projectile penetration while retaining some structural function during the healing processes. Although there are materials known to possess this capability, they are typically not considered for structural applications. Current efforts use inexpensive experimental methods to inflict damage, after which analytical procedures are identified to verify that function is restored. Two candidate self-healing polymer materials for structural engineering systems are used to test these experimental methods.

Recycling of plastic waste: Presence of phthalates in plastics from households and industry.

PubMed

Pivnenko, K; Eriksen, M K; Martín-Fernández, J A; Eriksson, E; Astrup, T F

2016-08-01

Plastics recycling has the potential to substitute virgin plastics partially as a source of raw materials in plastic product manufacturing. Plastic as a material may contain a variety of chemicals, some potentially hazardous. Phthalates, for instance, are a group of chemicals produced in large volumes and are commonly used as plasticisers in plastics manufacturing. Potential impacts on human health require restricted use in selected applications and a need for the closer monitoring of potential sources of human exposure. Although the presence of phthalates in a variety of plastics has been recognised, the influence of plastic recycling on phthalate content has been hypothesised but not well documented. In the present work we analysed selected phthalates (DMP, DEP, DPP, DiBP, DBP, BBzP, DEHP, DCHP and DnOP) in samples of waste plastics as well as recycled and virgin plastics. DBP, DiBP and DEHP had the highest frequency of detection in the samples analysed, with 360μg/g, 460μg/g and 2700μg/g as the maximum measured concentrations, respectively. Among other, statistical analysis of the analytical results suggested that phthalates were potentially added in the later stages of plastic product manufacturing (labelling, gluing, etc.) and were not removed following recycling of household waste plastics. Furthermore, DEHP was identified as a potential indicator for phthalate contamination of plastics. Close monitoring of plastics intended for phthalates-sensitive applications is recommended if recycled plastics are to be used as raw material in production. Copyright © 2016 Elsevier Ltd. All rights reserved.

Preliminary evaluation of physical and chemical characterization of waste palm oil shell as cool material replaced in asphaltic concrete as fine aggregate

NASA Astrophysics Data System (ADS)

Anuar, M. A. M.; Anting, N.; Shahidan, S.; Lee, Y. Y.; Din, M. F. Md; Khalid, F. S.; Nazri, W. M. H. W.

2017-11-01

Malaysia is one of the biggest producer of palm oil product and currently as main source of economy for the country. During the production of crude palm oil, a large amount of waste material is generated, such as palm oil fibres, palm oil shells and empty fruit bunches. Palm oil shell aggregate (POSA) is identified as a material that shows good potential to be used as a fine aggregate replacement in asphaltic concrete. On other hand, the chemical compound that exist in the Palm Oil Shell (POS) have shown a good potential as reflective component in cool-material. The purpose of this study is to obtain the physical and chemical properties of palm oil shell. The result shows the apparent particle density of Palm Oil Shell is 1.6 mg/m3. The specific gravity of palm oil shell was obtained with the value 1.6 and the water absorption amount of palm oil shell recorded from this study was 25.1%. The X-Ray Fluorescence study shows that palm oil shell contains the highest amount of SiO2 (46.412 wt%) and the second highest amount of Fe2O3 (34.016 wt%), both is the main output of relectivity compound. As a conclusion, waste palm oil shell has a potential to be used as alternative material for fine aggregate replacement. Besides that, the amount of chemical element that consist in palm oil shell which high in SiO2 and Fe2O3, promising the benefit to mitigate urban heat island as a cooling material agent.

Dual energy computed tomography for the head.

PubMed

Naruto, Norihito; Itoh, Toshihide; Noguchi, Kyo

2018-02-01

Dual energy CT (DECT) is a promising technology that provides better diagnostic accuracy in several brain diseases. DECT can generate various types of CT images from a single acquisition data set at high kV and low kV based on material decomposition algorithms. The two-material decomposition algorithm can separate bone/calcification from iodine accurately. The three-material decomposition algorithm can generate a virtual non-contrast image, which helps to identify conditions such as brain hemorrhage. A virtual monochromatic image has the potential to eliminate metal artifacts by reducing beam-hardening effects. DECT also enables exploration of advanced imaging to make diagnosis easier. One such novel application of DECT is the X-Map, which helps to visualize ischemic stroke in the brain without using iodine contrast medium.

The Role of Physical Representations in Solving Number Problems: A Comparison of Young Children's Use of Physical and Virtual Materials

ERIC Educational Resources Information Center

Manches, Andrew; O'Malley, Claire; Benford, Steve

2010-01-01

This research aims to explore the role of physical representations in young children's numerical learning then identify the benefits of using a graphical interface in order to understand the potential for developing interactive technologies in this domain. Three studies are reported that examined the effect of using physical representations…

Returning to the Job Market: A Woman's Guide to Employment Planning.

ERIC Educational Resources Information Center

American Association of Retired Persons, Washington, DC.

Intended for midlife and older women in the job market, this booklet is designed to help them in the process of looking for work outside the home. It helps them assess current skills and identify potential employment barriers; teaches them how to prepare effective written materials to support the job search and how to interview successfully; and…

Complete Genome Sequence of Bacillus horikoshii Strain 20a from Cuatro Cienegas, Coahuila, Mexico

PubMed Central

Alcaraz, Luis D.; Aguilar-Salinas, Bernardo; Islas, Africa

2017-01-01

ABSTRACT We sequenced the Bacillus horikoshii 20a genome, isolated from sediment collected in Cuatro Cienegas, Mexico. We identified genes involved in establishing antagonistic interactions in microbial communities (antibiotic resistance and bacteriocins) and genes related to the metabolism of cyanophycin, a reserve compound and spore matrix material potentially relevant for survival in an oligotrophic environment. PMID:28751383

MICROBIALLY MEDIATED LEACHING OF RARE EARTH ELEMENTS FROM RECYCLABLE MATERIALS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reed, D. W.; Fujita, Y.; Daubaras, D. L.

2016-09-01

Bioleaching offers a potential approach for recovery of rare earth elements (REE) from recyclable materials, such as fluorescent lamp phosphors or degraded industrial catalysts. Microorganisms were enriched from REE-containing ores and recyclable materials with the goal of identifying strains capable of extracting REE from solid materials. Over 100 heterotrophic microorganisms were isolated and screened for their ability to produce organic acids capable of leaching REE. The ten most promising isolates were most closely related to Pseudomonas, Acinetobacter and Talaromyces. Of the acids produced, gluconic acid appeared to be the most effective at leaching REE (yttrium, lanthanum, cerium, europium, and terbium)more » from retorted phosphor powders (RPP), fluidized cracking catalyst (FCC), and europium-doped yttrium oxide (YOEu). We found that an Acinetobacter isolates, BH1, was the most capable strain and able to leach 33% of the total REE content from the FCC material. These results support the continuing evaluation of gluconic acid-producing microbes for large-scale REE recovery from recyclable materials.« less

Martial recycling from renewable landfill and associated risks: A review.

PubMed

Ziyang, Lou; Luochun, Wang; Nanwen, Zhu; Youcai, Zhao

2015-07-01

Landfill is the dominant disposal choice for the non-classified waste, which results in the stockpile of materials after a long term stabilization process. A novel landfill, namely renewable landfill (RL), is developed and applied as a strategy to recycle the residual materials and reuse the land occupation, aim to reduce the inherent problems of large land occupied, materials wasted and long-term pollutants released in the conventional landfill. The principle means of RL is to accelerate the waste biodegradation process in the initial period, recover the various material resources disposal and extend the landfill volume for waste re-landfilling after waste stabilized. The residual material available and risk assessment, the methodology of landfill excavation, the potential utilization routes for different materials, and the reclamation options for the unsanitary landfill are proposed, and the integrated beneficial impacts are identified finally from the economic, social and environmental perspectives. RL could be draw as the future reservoirs for resource extraction. Copyright © 2015 Elsevier Ltd. All rights reserved.

Computer-aided discovery of a metal-organic framework with superior oxygen uptake.

PubMed

Moghadam, Peyman Z; Islamoglu, Timur; Goswami, Subhadip; Exley, Jason; Fantham, Marcus; Kaminski, Clemens F; Snurr, Randall Q; Farha, Omar K; Fairen-Jimenez, David

2018-04-11

Current advances in materials science have resulted in the rapid emergence of thousands of functional adsorbent materials in recent years. This clearly creates multiple opportunities for their potential application, but it also creates the following challenge: how does one identify the most promising structures, among the thousands of possibilities, for a particular application? Here, we present a case of computer-aided material discovery, in which we complete the full cycle from computational screening of metal-organic framework materials for oxygen storage, to identification, synthesis and measurement of oxygen adsorption in the top-ranked structure. We introduce an interactive visualization concept to analyze over 1000 unique structure-property plots in five dimensions and delimit the relationships between structural properties and oxygen adsorption performance at different pressures for 2932 already-synthesized structures. We also report a world-record holding material for oxygen storage, UMCM-152, which delivers 22.5% more oxygen than the best known material to date, to the best of our knowledge.

A Visual Decision Aid for Gear Materials Selection

NASA Astrophysics Data System (ADS)

Maity, S. R.; Chakraborty, S.

2013-10-01

Materials play an important role during the entire design process and the designers need to identify materials with specific functionalities in order to find out feasible design concepts. While selecting materials for engineering designs from an ever-increasing array of alternatives, with each having its own characteristics, applications, advantages and limitations, a clear understanding of the functional requirements for each individual component is required and various important criteria need to be considered. Although various approaches have already been adopted by the past researchers to solve the material selection problems, they all require profound knowledge in mathematics from the part of the designers for their implementation. This paper proposes the application of an integrated preference ranking organization method for enrichment evaluation and geometrical analysis for interactive aid method as a visual decision aid for material selection. Two real time gear material selection problems are solved which prove the potentiality and usefulness of this combined approach. It is observed that Nitralloy 135M and Nylon glass fiber reinforced 6/6 are respectively the choicest metallic and non-metallic gear materials.

Biological Evaluation of the Copper/Low-density Polyethylene Nanocomposite Intrauterine Device

PubMed Central

Wang, Hong; Li, Jun; Xie, Changsheng; Duan, Zhuo; Sun, Li-Kui; Wang, Xin; Zhu, Changhong

2013-01-01

Devices and materials intended for clinical applications as medical and implant devices should be evaluated to determine their biocompatibility in physiological systems. This article presents results from cytotoxicity assay of L929 mouse fibroblasts culture, tests for skin irritation, intracutaneous reactivity and sensitization, and material implantation tests for the novel copper/low-density polyethylene nanocomposite intrauterine device (nano-Cu/LDPE IUD) with potential for future clinical utilization. Cytotoxicity test in vitro was conducted to evaluate the change in morphology, growth and proliferation of cultured L929 mouse fibroblasts, which in vivo examination for skin irritation (n = 6) and intracutaneous reactivity (n = 6) were carried out to explore the irritant behavior in New Zealand White rabbits. Skin sensitization was implemented to evaluate the potential skin sensitizing in Hartley guinea pigs (n = 35). The materials were implanted into the spinal muscle of rabbits (n = 9). The cytotoxicity grade of the nano-Cu/LDPE IUD was 0–1, suggested that the composite was nontoxic or mildly cytotoxic; no irritation reaction and skin sensitization were identified in any animals of specific extracts prepared from the material under test; similarly to the control sides, the inflammatory reaction was observed in the rabbits living tissue of the implanted material in intramuscular implantation assay. They indicated that the novel composite intrauterine device presented potential for this type of application because they meet the requirements of the standard practices recommended for evaluating the biological reactivity. The nano-Cu/LDPE IUD has good biocompatibility, which is biologically safe for the clinical research as a novel contraceptive device. PMID:24058521

Biological evaluation of the copper/low-density polyethylene nanocomposite intrauterine device.

PubMed

Hu, Li-Xia; He, Jing; Hou, Li; Wang, Hong; Li, Jun; Xie, Changsheng; Duan, Zhuo; Sun, Li-Kui; Wang, Xin; Zhu, Changhong

2013-01-01

Devices and materials intended for clinical applications as medical and implant devices should be evaluated to determine their biocompatibility in physiological systems. This article presents results from cytotoxicity assay of L929 mouse fibroblasts culture, tests for skin irritation, intracutaneous reactivity and sensitization, and material implantation tests for the novel copper/low-density polyethylene nanocomposite intrauterine device (nano-Cu/LDPE IUD) with potential for future clinical utilization. Cytotoxicity test in vitro was conducted to evaluate the change in morphology, growth and proliferation of cultured L929 mouse fibroblasts, which in vivo examination for skin irritation (n = 6) and intracutaneous reactivity (n = 6) were carried out to explore the irritant behavior in New Zealand White rabbits. Skin sensitization was implemented to evaluate the potential skin sensitizing in Hartley guinea pigs (n = 35). The materials were implanted into the spinal muscle of rabbits (n = 9). The cytotoxicity grade of the nano-Cu/LDPE IUD was 0-1, suggested that the composite was nontoxic or mildly cytotoxic; no irritation reaction and skin sensitization were identified in any animals of specific extracts prepared from the material under test; similarly to the control sides, the inflammatory reaction was observed in the rabbits living tissue of the implanted material in intramuscular implantation assay. They indicated that the novel composite intrauterine device presented potential for this type of application because they meet the requirements of the standard practices recommended for evaluating the biological reactivity. The nano-Cu/LDPE IUD has good biocompatibility, which is biologically safe for the clinical research as a novel contraceptive device.

Evaluation of laser-induced breakdown spectroscopy analysis potential for addressing radiological threats from a distance

NASA Astrophysics Data System (ADS)

Gaona, I.; Serrano, J.; Moros, J.; Laserna, J. J.

2014-06-01

Although radioactive materials are nowadays valuable tools in nearly all fields of modern science and technology, the dangers stemming from the uncontrolled use of ionizing radiation are more than evident. Since preparedness is a key issue to face the risks of a radiation dispersal event, development of rapid and efficient monitoring technologies to control the contamination caused by radioactive materials is of crucial interest. Laser-induced breakdown spectroscopy (LIBS) exhibits appealing features for this application. This research focuses on the assessment of LIBS potential for the in-situ fingerprinting and identification of radioactive material surrogates from a safe distance. LIBS selectivity and sensitivity to detect a variety of radioactive surrogates, namely 59Co, 88Sr, 130Ba, 133Cs, 193Ir and 238U, on the surface of common urban materials at a distance of 30 m have been evaluated. The performance of the technique for nuclear forensics has been also studied on different model scenarios. Findings have revealed the difficulties to detect and to identify the analytes depending on the surface being interrogated. However, as demonstrated, LIBS shows potential enough for prompt and accurate gathering of essential evidence at a number of sites after the release, either accidental or intentional, of radioactive material. The capability of standoff analysis confers to LIBS unique advantages in terms of fast and safe inspection of forensic scenarios. The identity of the radioactive surrogates is easily assigned from a distance and the sensitivity to their detection is in the range of a few hundreds of ng per square centimeter.

LDEF materials: An overview of the interim findings

NASA Technical Reports Server (NTRS)

Stein, Bland A.

1992-01-01

The flight and retrieval of the National Aeronautics and Space Administration's Long Duration Exposure Facility (LDEF) provided an opportunity for the study of the low-Earth orbit (LEO) environment and long-duration space environmental effect (SEE) on materials that are unparalleled in the history of the U.S. space program. The 5.8-year flight of LDEF greatly enhanced the potential value of materials data from LDEF to the international SEE community, compared to that of the original 1-year flight plan. The remarkable flight attitude stability of LDEF enables specific analyses of various individual and combined effects of LEO environmental parameters on identical materials of the same space vehicle. NASA recognized the potential by forming the LDEF Space Environmental Effects on Materials Special Investigation Group (MSIG) to address the greatly expanded materials and LEO space environment parameter analysis opportunities available in the LDEF structure, experiment trays, and corollary measurements, so that the combined value of all LDEF materials data to current and future space missions will be assessed and documented. This paper provides an overview of the interim LDEF materials findings of the Principal Investigators and the Materials Special Investigation Group. These revelations are based on observations of LEO environmental effects on materials made in-space during LDEF retrieval and during LDEF tray deintegration at the Kennedy Space Center, and on findings of approximately 1.5 years of laboratory analyses of LDEF materials by the LDEF materials scientists. These findings were extensively reviewed and discussed at the MSIG-sponsored LDEF Materials Workshop '91. The results are presented in a format which categorizes the revelations as 'clear findings' or 'confusing/unexplained findings' and resultant needs for new space materials developments and ground simulation testing/analytical modeling in seven categories: environmental parameters and data bases; LDEF contamination; thermal control coatings and protective treatments; polymers and films; polymer-matrix composites; metals, ceramics, and optical materials; and systems-related materials. General outlines of findings of the other LDEF Special Investigation Groups (Ionizing Radiation, Meteoroid and Debris, and Systems) are also included. The utilization of LDEF materials data for future low-earth orbit missions is also discussed, concentrating on Space Station Freedom. Some directions for continuing studies of LDEF materials are outlined. In general, the LDEF data is remarkable consistent; LDEF will provide a 'benchmark' for materials design data bases for satellites in low-Earth orbit. Some materials were identified to be encouragingly resistant to LEO SEE for 5.8-years; other 'space qualified' materials displayed significant environmental degradation. Molecular contamination was widespread; LDEF offers an unprecedented opportunity to provide a unified perspective of unmanned LEO spacecraft contamination mechanisms. New material development requirements for long-term LEO missions have been identified and current ground simulation testing methods/data for new, durable materials concepts can be validated with LDEF results. LDEF findings are already being integrated into the design of Space Station Freedom.

Air pollution, cardiovascular endpoints and susceptibility by stress and material resources: a systematic review of the evidence.

PubMed

Fuller, Christina H; Feeser, Karla R; Sarnat, Jeremy A; O'Neill, Marie S

2017-06-14

Evidence shows that both the physical and social environments play a role in the development of cardiovascular disease. The purpose of this systematic review is two-fold: First, we summarize research from the past 12 years from the growing number of studies focused on effect modification of the relationships between air pollution and cardiovascular disease (CVD) outcomes by socioeconomic position (SEP) and; second, we identify research gaps throughout the published literature on this topic and opportunities for addressing these gaps in future study designs. We identified 30 articles that examined the modifying effects of either material resources or psychosocial stress (both related to SEP) on associations between short and long-term air pollution exposure and CVD endpoints. Although 18 articles identified at least one interaction between an air pollutant and material resource indicator, 11 others did not. Support for susceptibility to air pollution by psychosocial stress was weaker; however, only three articles tested this hypothesis. Further studies are warranted to investigate how air pollution and SEP together may influence CVD. We recommend that such research include thorough assessment of air pollution and SEP correlations, including spatial correlation; investigate air pollution indices or multi-pollutant models; use standardized metrics of SEP to enhance comparability across studies; and evaluate potentially susceptible populations.

Fundamental investigation of the tribological and mechanical responses of materials and nanostructures

NASA Astrophysics Data System (ADS)

Bucholz, Eric W.

In the field of tribology, the ability to predict, and ultimately control, frictional performance is of critical importance for the optimization of tribological systems. As such, understanding the specific mechanisms involved in the lubrication processes for different materials is a fundamental step in tribological system design. In this work, a combination of computational and experimental methods that include classical molecular dynamics (MD) simulations, atomic force microscopy (AFM) experiments, and multivariate statistical analyses provides fundamental insight into the tribological and mechanical properties of carbon-based and inorganic nanostructures, lamellar materials, and inorganic ceramic compounds. One class of materials of modern interest for tribological applications is nanoparticles, which can be employed either as solid lubricating films or as lubricant additives. In experimental systems, however, it is often challenging to attain the in situ observation of tribological interfaces necessary to identify the atomic-level mechanisms involved during lubrication and response to mechanical deformation. Here, classical MD simulations establish the mechanisms occurring during the friction and compression of several types of nanoparticles including carbon nano-onions, amorphous carbon nanoparticles, and inorganic fullerene-like MoS2 nanoparticles. Specifically, the effect of a nanoparticle's structural properties on the lubrication mechanisms of rolling, sliding, and lamellar exfoliation is indicated; the findings quantify the relative impact of each mechanism on the tribological and mechanical properties of these nanoparticles. Beyond identifying the lubrication mechanisms of known lubricating materials, the continual advancement of modern technology necessitates the identification of new candidate materials for use in tribological applications. To this effect, atomic-scale AFM friction experiments on the aluminosilicate mineral pyrophyllite demonstrate that pyrophyllite provides a low friction coefficient and low shear stresses as well as a high threshold to interfacial wear; this suggests the potential for use of pyrophyllite as a lubricious material under specific conditions. Also, a robust and accurate model for estimating the friction coefficients of inorganic ceramic materials that is based on the fundamental relationships between material properties is presented, which was developed using multivariate data mining algorithms. These findings provide the tribological community with a new means of quickly identifying candidate materials that may provide specific frictional properties for desired applications.

Active materials for automotive adaptive forward lighting Part 1: system requirements vs. material properties

NASA Astrophysics Data System (ADS)

Keefe, Andrew C.; Browne, Alan L.; Johnson, Nancy L.

2011-04-01

Adaptive Frontlighting Systems (AFS in GM usage) improve visibility by automatically optimizing the beam pattern to accommodate road, driving and environmental conditions. By moving, modifying, and/or adding light during nighttime, inclement weather, or in sharp turns, the driver is presented with dynamic illumination not possible with static lighting systems The objective of this GM-HRL collaborative research project was to assess the potential of active materials to decrease the cost, mass, and packaging volume of current electric stepper-motor AFS designs. Solid-state active material actuators, if proved suitable for this application, could be less expensive than electric motors and have lower part count, reduced size and weight, and lower acoustic and EMF noise1. This paper documents Part 1 of the collaborative study, assessing technically mature, commercially available active materials for use as actuators. Candidate materials should reduce cost and improve AFS capabilities, such as increased angular velocity on swivel. Additional benefits to AFS resulting from active materials actuators were to be identified as well such as lower part count. In addition, several notional approaches to AFS were documented to illustrate the potential function, which is developed more fully in Part 2. Part 1 was successful in verifying the feasibility of using two active materials for AFS: shape memory alloys, and piezoelectrics. In particular, this demonstration showed that all application requirements including those on actuation speed, force, and cyclic stability to effect manipulation of the filament assembly and/or the reflector could be met by piezoelectrics (as ultrasonic motors) and SMA wire actuators.

THE EFFECT OF MERCURY CONTROLS ON WALLBOARD MANUFACTURE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sandra Meischen

2004-07-01

Pending EPA regulations may mandate 70 to 90% mercury removal efficiency from utility flue gas. A mercury control option is the trapping of oxidized mercury in wet flue gas desulfurization systems (FGD). The potential doubling of mercury in the FGD material and its effect on mercury volatility at temperatures common to wallboard manufacture is a concern that could limit the growing byproduct use of FGD material. Prediction of mercury fate is limited by lack of information on the mercury form in the FGD material. The parts per billion mercury concentrations prevent the identification of mercury compounds by common analytical methods.more » A sensitive analytical method, cold vapor atomic fluorescence, coupled with leaching and thermodecomposition methods were evaluated for their potential to identify mercury compounds in FGD material. The results of the study suggest that the mercury form is dominated by the calcium sulfate matrix and is probably associated with the sulfate form in the FGD material. Additionally, to determine the effect of high mercury concentration FGD material on wallboard manufacture, a laboratory FGD unit was built to trap the oxidized mercury generated in a simulated flue gas. Although the laboratory prepared FGD material did not contain the mercury concentrations anticipated, further thermal tests determined that mercury begins to evolve from FGD material at 380 to 390 F, consequently dropping the drying temperature should mitigate mercury evolution if necessary. Mercury evolution is also diminished as the weight of the wallboard sample increased. Consequently, mercury evolution may not be a significant problem in wallboard manufacture.« less

Safety analysis of occupational exposure of healthcare workers to residual contaminations of cytotoxic drugs using FMECA security approach.

PubMed

Le, Laetitia Minh Mai; Reitter, Delphine; He, Sophie; Bonle, Franck Té; Launois, Amélie; Martinez, Diane; Prognon, Patrice; Caudron, Eric

2017-12-01

Handling cytotoxic drugs is associated with chemical contamination of workplace surfaces. The potential mutagenic, teratogenic and oncogenic properties of those drugs create a risk of occupational exposure for healthcare workers, from reception of starting materials to the preparation and administration of cytotoxic therapies. The Security Failure Mode Effects and Criticality Analysis (FMECA) was used as a proactive method to assess the risks involved in the chemotherapy compounding process. FMECA was carried out by a multidisciplinary team from 2011 to 2016. Potential failure modes of the process were identified based on the Risk Priority Number (RPN) that prioritizes corrective actions. Twenty-five potential failure modes were identified. Based on RPN results, the corrective actions plan was revised annually to reduce the risk of exposure and improve practices. Since 2011, 16 specific measures were implemented successively. In six years, a cumulative RPN reduction of 626 was observed, with a decrease from 912 to 286 (-69%) despite an increase of cytotoxic compounding activity of around 23.2%. In order to anticipate and prevent occupational exposure, FMECA is a valuable tool to identify, prioritize and eliminate potential failure modes for operators involved in the cytotoxic drug preparation process before the failures occur. Copyright © 2017 Elsevier B.V. All rights reserved.

A device-specific prioritization strategy based on the potential for harm to human health in informal WEEE recycling.

PubMed

Cesaro, Alessandra; Belgiorno, Vincenzo; Vaccari, Mentore; Jandric, Aleksander; Chung, Tran Duc; Dias, Maria Isabel; Hursthouse, Andrew; Salhofer, Stefan

2018-01-01

In developing countries, the recovery of valuable materials from Waste Electrical and Electronic Equipment (WEEE) is carried out via uncontrolled practices, posing potentially severe risks both to human health and the environment. The assessment of the risk, which depends on both the kind and hazardous properties of the substances contained in WEEE, is currently limited as the exposure scenario for the single informal practice cannot be fully characterized for this purpose. In this context, this work proposes and evaluates a strategy to identify the relative potential harm of different kinds of WEEE by their content in metals, selected as the target substances of concern. This was based on the individual metal content, primarily located in the printed circuit boards (PCBs) of the different devices. The metal composition of the individual PCBs was identified and the dominant unregulated metal recovery practices were reviewed to identify the most suitable parameter to express the toxicity of these metals. Based on a mass-normalized cumulative toxicity, via the inhalation route, individual components were assessed from compositional variation found in the literature. The results is a semiquantitative ranking of individual components, revealing significant differences in potential harm posed by different electronic appliances and an opportunity to provide prioritization strategies in future management.

Study of the 3D Euler equations using Clebsch potentials: dual mechanisms for geometric depletion

NASA Astrophysics Data System (ADS)

Ohkitani, Koji

2018-02-01

After surveying analyses of the 3D Euler equations using the Clebsch potentials scattered over the literature, we report some preliminary new results. 1. Assuming that flow fields are free from nulls of the impulse and the vorticity fields, we study how constraints imposed by the Clebsch potentials lead to a degenerate geometrical structure, typically in the form of depletion of nonlinearity. We consider a vorticity surface spanned by \\boldsymbol ω and another material vector \\boldsymbol {W} such that \\boldsymbol γ=\\boldsymbol ω× \\boldsymbol {W}, where \\boldsymbol γ is the impulse variable in geometric gauge. We identify dual mechanism for geometric depletion and show that at least of one them is acting if \\boldsymbol {W} does not develop a null. This suggests that formation of singularity in flows endowed with Clebsch potentials is less likely to happen than in more general flows. Some arguments are given towards exclusion of ‘type I’ blowup. A mathematical challenge remains to rule out singularity formation for flows which have Clebsch potentials everywhere. 2. We exploit classical differential geometry kinematically to write down the Gauss-Weingarten equations for the vorticity surface of the Clebsch potential in terms of fluid dynamical variables, as are the first, second and third fundamental forms. In particular, we derive a constraint on the size of the Gaussian curvature near the point of a possible singularity. On the other hand, an application of the Gauss-Bonnet theorem reveals that the tangential curvature of the surface becomes large in the neighborhood of near-singularity. 3. Using spatially-periodic flows with highly-symmetry, i.e. initial conditions of the Taylor-Green vortex and the Kida-Pelz flow, we present explicit formulas of the Clebsch potentials with exceptional singular surfaces where the Clebsch potentials are undefined. This is done by connecting the known expressions with the solenoidal impulse variable (i.e. the incompressible velocity) using suitable canonical transforms. By a simple argument we show that they keep forming material separatrices under the time evolution of the 3D Euler equations. We argue on this basis that a singularity, if developed, will be associated with these exceptional material surfaces. The difficulty of having Clebsch potentials globally on all of space have been with us for a long time. The proposal rather seeks to turn the difficulty into an advantage by using their absence to identify and locate possible singularities.

The search for materials to mitigate spacecraft charging

NASA Technical Reports Server (NTRS)

Losure, Nancy S.

1996-01-01

As spacecraft orbit the earth, they encounter a variety of particles and radiation. Charged particles are common enough that a spacecraft can collect substantial charges on its surfaces. If these charges are not bled off, they can accumulate until electrostatic discharges occur between a charged surface and some lower-potential location on the craft. Electrostatic discharge (ESD) is the suspected culprit in a number of spacecraft failures. Silverized Teflon film has become the standard heat-reflecting outer layer of spacecraft because of its flexibility, chemical inertness, and low volatiles content. However, as spacecraft are designed to operate in orbits with greater probability of accumulating enough ions and electrons to create ESD, the Teflon-based thermal control blankets are becoming a liability. Unless stringent (and sometimes burdensome) shielding measures are taken, ESD can upset delicate electronic systems by upsetting or destroying components, interfering with radio signals, garbling internal instructions, and so on. As orbits become higher and more eccentric, as electronics become more sensitive, and as fault-free operation becomes more crucial, it is becoming necessary to find a replacement for silver/Teflon that has comparable strength, flexibility and chemical inertness, as well as a much lower potential for ESD. This is a report of the steps taken toward the goal of selecting a replacement for silver/Teflon during the Summer of 1995. It is a condensation of a much larger report available on request from the author. Three tasks were undertaken. Task 1 was to specify desirable properties for thermal control blankets. The second task was to collect data on materials properties from the literature and organize into a format useful for identifying candidate materials. The third task was to identify candidate materials and begin testing.

Gale Crater Surface Materials

NASA Image and Video Library

2015-06-19

Gale Crater, home to NASA's Curiosity Mars rover, shows a new face in this mosaic image made using data from the Thermal Emission Imaging System (THEMIS) on NASA's Mars Odyssey orbiter. The colors come from an image processing technique that identifies mineral differences in surface materials and displays them in false colors. For example, windblown dust appears pale pink and olivine-rich basalt looks purple. The bright pink on Gale's floor appears due to a mix of basaltic sand and windblown dust. The blue at the summit of Gale's central mound, Mount Sharp, probably comes from local materials exposed there. The typical average Martian surface soil looks grayish-green. Scientists use false-color images such as these to identify places of potential geologic interest. The diameter of the crater is 96 miles (154 kilometers). North is up. THEMIS and other instruments on Mars Odyssey have been studying Mars from orbit since 2001. Curiosity landed in the northeastern portion of Gale Crater in 2012 and climbed onto the flank of Mount Sharp in 2014. http://photojournal.jpl.nasa.gov/catalog/PIA19674

Final safety analysis report for the Galileo mission: Volume 3 (Book 2), Nuclear risk analysis document: Appendices: Revision 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1989-01-25

It is the purpose of the NRAD to provide an analysis of the range of potential consequences of accidents which have been identified that are associated with the launching and deployment of the Galileo mission spacecraft. The specific consequences analyzed are those associated with the possible release of radioactive material (fuel) of the Radioisotope Thermoelectric Generators (RTGs). They are in terms of radiation doses to people and areas of deposition of radioactive material. These consequence analyses can be used in several ways. One way is to identify the potential range of consequences which might have to be dealt with ifmore » there were to be an accident with a release of fuel, so as to assure that, given such an accident, the health and safety of the public will be reasonably protected. Another use of the information, in conjunction with accident and release probabilities, is to estimate the risks associated with the mission. That is, most space launches occur without incident. Given an accident, the most probable result relative to the RTGs is complete containment of the radioactive material. Only a small fraction of accidents might result in a release of fuel and subsequent radiological consequences. The combination of probability with consequence is risk, which can be compared to other human and societal risks to assure that no undue risks are implied by undertaking the mission. Book 2 contains eight appendices.« less

Safety analysis report for the Galileo Mission. Volume 3, book 2: Nuclear risk analysis document. Appendices, revision 1

NASA Astrophysics Data System (ADS)

1989-01-01

It is the purpose of the NRAD to provide an analysis of the range of potential consequences of accidents which have been identified that are associated with the launching and deployment of the Galileo mission spacecraft. The specific consequences analyzed are those associated with the possible release of radioactive material (fuel) of the Radioisotope Thermoelectric Generators (RTGs). They are in terms of radiation doses to people and areas of deposition of radioactive material. These consequence analyses can be used in several ways. One way is to identify the potential range of consequences which might have to be dealt with if there were to be an accident with a release of fuel, so as to assure that, given such an accident, the health and safety of the public will be reasonably protected. Another use of the information, in conjunction with accident and release probabilities, is to estimate the risks associated with the mission. That is, most space launches occur without incident. Given an accident, the most probable result relative to the RTGs is complete containment of the radioactive material. Only a small fraction of accidents might result in a release of fuel and subsequent radiological consequences. The combination of probability with consequence is risk, which can be compared to other human and societal risks to assure that no undue risks are implied by undertaking the mission. Book 2 contains eight appendices.

Regional and Localized Deposits on the Moon

NASA Technical Reports Server (NTRS)

Coombs, Cassandra R.

1996-01-01

Earth-based telescopic remote sensing studies have provided important information concerning lunar pyroclastic deposits. Combined with the returned lunar sample studies and analyses of lunar photography, we have learned a great deal about the nature and origin of these explosive volcanic materials. Lunar pyroclastic deposits are more numerous, extensive, and widely distributed than previously thought. Two generic classes of lunar pyroclastics have been identified, regional and localized. From the former, two separate spectral compositional groups have been identified; one is dominated by Fe(2+)-bearing glasses, the other is composed of ilmenite-rich black spheres. Comparatively, three separate spectral groups have been identified among the localized deposits: highlands-rich, olivine-rich, and mare-rich. Returned sample studies and the recently collected Galileo and Clementine data also corroborate these findings. Albedo data and multispectral imagery suggest that the thicker core deposits of the regional dark mantle deposits (RDMD) are surrounded by pyroclastic debris and subjacent highlands material. The presence of a major component of pyroclastic debris in the regolith surrounding the core regional deposits has important implications for the resource potential of these materials. Both telescopic and orbital spectra indicate that the regional pyroclastic deposits are rich in iron, titanium and oxygen-bearing minerals. Particle shapes vary from simple glass spheres to compound droplets with quench crystallized textures. Their small grain size and friability make them ideal indigenous feedstock. Compared to other resource feedstock sources on the Moon, these pyroclastic materials may be the best oxygen resource on the Moon.

Assessment of agroforestry residue potentials for the bioeconomy in the European Union.

PubMed

Thorenz, Andrea; Wietschel, Lars; Stindt, Dennis; Tuma, Axel

2018-03-01

The biobased chemical industry is characterised by strong growth. Innovative products and materials such as biopolymers have been developed, and current European demand for biopolymers exceeds the domestic supply. Agroforestry residues can serve as main sources of the basic building blocks for chemicals and materials. This work assesses sustainably available agroforestry residues to feed a high added-value materials and product bioeconomy. To evaluate bioeconomic potential, a structured three-step approach is applied. Cultivation practices, sustainability issues, legislative restrictions, technical limitations and competitive applications are considered. All data regarding bioeconomic potential are processed on a regional level and mapped by ArcGIS. Our results identify wheat straw as the most promising source in the agricultural sector, followed by maize stover, barley straw and rape straw, which all contain a total concentration of lignocellulose of more than 80% of dry matter. In the forestry sector, residue bark from two coniferous species, spruce and pine, is the most promising source, with approximately 70% lignocellulose. Additionally, coniferous bark contains considerable amounts of tannin, which has attracted increasing interest for industrial utilisation. A sensitivity analysis concerning removal rates, residue-to-crop ratios, changes in farming technologies and competing applications is applied at the end of the study to consolidate our results.

Methane production and hydrolysis kinetics in the anaerobic degradation of wastewater screenings.

PubMed

Cadavid-Rodríguez, L S; Horan, N

2013-01-01

Anaerobic biodegradability and hydrolysis rates of wastewater screenings were determined using the biochemical methane potential test at 37 °C. The extent and rate of screenings conversion to methane of this complex and particulate substrate were investigated and since two stages of hydrolysis were identified, corresponding to the different types of materials in screenings, a linear and non-linear model was used. No accumulation of intermediary products was observed and so it was possible to use the methane production rate and a linear model to estimate the hydrolysis rate in the first phase of hydrolysis. The measured values of 0.061-0.127 d(-1) are in the range reported for other comparable organic wastes. It was also observed that the inoculum-to-substrate ratio has a large impact on methane production rate of screenings. The difference in biodegradation rates from the materials in screenings and the overall hydrolysis could be represented by the modified Gompertz non-linear model which was able to describe the methane production rate of screenings with a high confidence. Screenings were found to have 52% biodegradability on average and this shows the potential for volatile solids destruction. A two-stage process with an improved hydrolysis rate is proposed to ensure that the full potential of the material is exploited.

Framing global health: the governance challenge.

PubMed

McInnes, Colin; Kamradt-Scott, Adam; Lee, Kelley; Reubi, David; Roemer-Mahler, Anne; Rushton, Simon; Williams, Owain David; Woodling, Marie

2012-01-01

With the emergence of global health comes governance challenges which are equally global in nature. This article identifies some of the initial limitations in analyses of global health governance (GHG) before discussing the focus of this special supplement: the framing of global health issues and the manner in which this impacts upon GHG. Whilst not denying the importance of material factors (such as resources and institutional competencies), the article identifies how issues can be framed in different ways, thereby creating particular pathways of response which in turn affect the potential for and nature of GHG. It also identifies and discusses the key frames operating in global health: evidence-based medicine, human rights, security, economics and development.

Chemical assessment and in vitro antioxidant capacity of Ficus carica latex.

PubMed

Oliveira, Andreia P; Silva, Luís R; Ferreres, Federico; Guedes de Pinho, Paula; Valentão, Patrícia; Silva, Branca M; Pereira, José A; Andrade, Paula B

2010-03-24

Ficus species possess latex-like material within their vasculatures, affording protection and self-healing from physical attacks. In this work, metabolite profiling was performed on Ficus carica latex. Volatiles profile was determined by HS-SPME/GC-IT-MS, with 34 compounds being identified, distributed by distinct chemical classes: 5 aldehydes, 7 alcohols, 1 ketone, 9 monoterpenes, 9 sesquiterpenes and 3 other compounds. Sesquiterpenes constituted the most abundant class in latex (ca. 91% of total identified compounds). Organic acids composition was also characterized, by HPLC-UV, and oxalic, citric, malic, quinic, shikimic and fumaric acids were determined. Malic and shikimic acids were present in higher amounts (ca. 26%, each). The antioxidant potential of this material was checked by distinct in vitro chemical assays. A concentration-dependent activity was noticed against DPPH, nitric oxide and superoxide radicals. Additionally, acetylcholinesterase inhibitory capacity was evaluated, but a weak effect was found.

Active Control of Charge Density Waves at Degenerate Semiconductor Interfaces

NASA Astrophysics Data System (ADS)

Vinnakota, Raj; Genov, Dentcho

We present numerical modeling of an active electronically controlled highly confined charge-density waves, i.e. surface plasmon polaritons (SPPs) at the metallurgic interfaces of degenerate semiconductor materials. An electro-optic switching element for fully-functional plasmonic circuits based on p-n junction semiconductor Surface Plasmon Polariton (SPP) waveguide is shown. Two figures of merits are introduced and parametric study has been performed identifying the device optimal operation range. The Indium Gallium Arsenide (In0.53Ga0.47As) is identified as the best semiconductor material for the device providing high optical confinement, reduced system size and fast operation. The electro-optic SPP switching element is shown to operate at signal modulation up to -24dB and switching rates surpassing 100GHz, thus potentially providing a new pathway toward bridging the gap between electronic and photonic devices. The current work is funded by the NSF EPSCoR CIMM project under award #OIA-1541079.

Occurrence of extractable ink residuals in packaging materials used in the Czech Republic.

PubMed

Dupáková, Z; Dobiás, J; Votavová, L; Klaudisová, K; Voldrich, M

2010-01-01

Residues of printing ink components were determined in 94 samples of packaging materials commercially used in the Czech Republic for food packaging. The samples tested included printed polyethylene and polypropylene films, co-extruded and laminated films, paperboard beverages boxes, foils for thermo sealing of polystyrene cups, and polypropylene cups. Printing ink components were extracted with diethylether, then separated and determined using gas chromatography-mass spectrometry (GC/MS). Fifty compounds potentially originating from printing were isolated, identified and quantified. No acute health risk for consumers were identified, even though several findings of high levels of photo-initiators (e.g. in polyethylene terephthalate (PET) films for thermo sealing of polystyrene cups) as well as plasticizers (acetyl tributyl citrate, tributyl aconitate, 2-butoxyethyl oleate and 2-ethylhexyl diphenyl phosphate in co-extruded films) indicate that their real migration into food and/or food simulants needs to be undertaken for a proper safety evaluation.

Materials for Advanced Turbine Engines (MATE). Project 4: Erosion resistant compressor airfoil coating

NASA Technical Reports Server (NTRS)

Rashid, J. M.; Freling, M.; Friedrich, L. A.

1987-01-01

The ability of coatings to provide at least a 2X improvement in particulate erosion resistance for steel, nickel and titanium compressor airfoils was identified and demonstrated. Coating materials evaluated included plasma sprayed cobalt tungsten carbide, nickel carbide and diffusion applied chromium plus boron. Several processing parameters for plasma spray processing and diffusion coating were evaluated to identify coating systems having the most potential for providing airfoil erosion resistance. Based on laboratory results and analytical evaluations, selected coating systems were applied to gas turbine blades and evaluated for surface finish, burner rig erosion resistance and effect on high cycle fatigue strength. Based on these tests, the following coatings were recommended for engine testing: Gator-Gard plasma spray 88WC-12Co on titanium alloy airfoils, plasma spray 83WC-17Co on steel and nickel alloy airfoils, and Cr+B on nickel alloy airfoils.

Plastic litter in aquatic environments of Maremma Regional Park (Tyrrhenian Sea, Italy): Contribution by the Ombrone river and levels in marine sediments.

PubMed

Guerranti, Cristiana; Cannas, Susanna; Scopetani, Costanza; Fastelli, Paolo; Cincinelli, Alessandra; Renzi, Monia

2017-04-15

During two surveys in 2015 and 2016, sediments samples were collected along the Ombrone river (Maremma Regional Park, province of Grosseto, Italy), in particular at its mouth and in the marine area in front of it, in order to quantify, identify and categorize plastic items (macro, meso and micro-plastics and colour, material etc.) and evaluate their potential sources. The Albegna and Osa rivers were identified as external areas of comparison. The results of the analysis showed different situations, especially as regards fluvial inputs, in addition to evidencing local provisions of plastic material derived from agricultural activities. The microplastics values per kg of sediment and the prevailing type of items found largely varied between the investigated sites (45-1069items/kg dry sample). Copyright © 2017 Elsevier Ltd. All rights reserved.

Pilot trial on separation conditions for diaper recycling.

PubMed

Kim, Kyung-Shin; Cho, Hee-Sun

2017-09-01

By utilizing laboratory-scale tests, the optimal separation conditions for diaper recycling were identified, and then, these conditions were validated by a pilot trial. In this research, we determined the mass balances derived during various processing steps and identified the most feasible procedures to use for separating each material in the output flow. The results showed that drum screening was not able to remove all the fiber and super absorbent particles (SAP) in the plastic-rich fraction and that cellulose enzyme treatment can be a good solution. To achieve better separation of fibers and SAP, slot screening followed by a cleaner is a potential option. A feasible diaper recycling process was recommended based on these results. This process involves screening and enzymatic treatment for the plastic fraction, and screening, cleaning, and thickening for the fiber fraction. Treatment procedures were also proposed for the SAP fraction and rejected materials. Copyright © 2017. Published by Elsevier Ltd.

Strawberry Accessions with Reduced Drosophila suzukii Emergence From Fruits

PubMed Central

Gong, Xiaoyun; Bräcker, Lasse; Bölke, Nadine; Plata, Camila; Zeitlmayr, Sarah; Metzler, Dirk; Olbricht, Klaus; Gompel, Nicolas; Parniske, Martin

2016-01-01

Drosophila suzukii is threatening soft fruit production worldwide due to the females’ ability to pierce through the intact skin of ripe fruits and lay eggs inside. Larval consumption and the associated microbial infection cause rapid fruit degradation, thus drastic yield and economic loss. Cultivars that limit the proliferation of flies may be ideal to counter this pest; however, they have not yet been developed or identified. To search for potential breeding material, we investigated the rate of adult D. suzukii emergence from individual fruits (fly emergence) of 107 accessions of Fragaria species that had been exposed to egg-laying D. suzukii females. We found significant variation in fly emergence across strawberries, which correlated with accession and fruit diameter, and to a lesser extent with the strawberry species background. We identified accessions with significantly reduced fly emergence, not explained by their fruit diameter. These accessions constitute valuable breeding material for strawberry cultivars that limit D. suzukii spread. PMID:28066452

Reversible amorphization and the catalytically active state of crystalline Co3O4 during oxygen evolution

PubMed Central

Bergmann, Arno; Martinez-Moreno, Elias; Teschner, Detre; Chernev, Petko; Gliech, Manuel; de Araújo, Jorge Ferreira; Reier, Tobias; Dau, Holger; Strasser, Peter

2015-01-01

Water splitting catalysed by earth-abundant materials is pivotal for global-scale production of non-fossil fuels, yet our understanding of the active catalyst structure and reactivity is still insufficient. Here we report on the structurally reversible evolution of crystalline Co3O4 electrocatalysts during oxygen evolution reaction identified using advanced in situ X-ray techniques. At electrode potentials facilitating oxygen evolution, a sub-nanometre shell of the Co3O4 is transformed into an X-ray amorphous CoOx(OH)y which comprises di-μ-oxo-bridged Co3+/4+ ions. Unlike irreversible amorphizations, here, the formation of the catalytically-active layer is reversed by re-crystallization upon return to non-catalytic electrode conditions. The Co3O4 material thus combines the stability advantages of a controlled, stable crystalline material with high catalytic activity, thanks to the structural flexibility of its active amorphous oxides. We propose that crystalline oxides may be tailored for generating reactive amorphous surface layers at catalytic potentials, just to return to their stable crystalline state under rest conditions. PMID:26456525

Design of a Helium Vapor Shroud for Liquid Hydrogen Fueling of an Unmanned Aerial Vehicle (UAV)

NASA Astrophysics Data System (ADS)

Cavender, K.; Evans, C.; Haney, J.; Leachman, J.

2017-12-01

Filling a vehicular liquid hydrogen fuel tank presents the potential for flammable mixtures due to oxygen concentration from liquid air condensation. Current liquid hydrogen tank designs utilize insulating paradigms such as aerogel/fiberglass materials, vacuum jackets, or inert gas purge systems to keep the outer surface from reaching the condensation temperature of air. This work examines the heat transfer at the refuelling connection of the tank to identify potential areas of condensation, as well as the surface temperature gradient. A shrouded inert gas purge was designed to minimize vehicle weight and refuelling time. The design of a shrouded inert gas purge system is presented to displace air preventing air condensation. The design investigates 3D printed materials for an inert gas shroud, as well as low-temperature sealing designs. Shroud designs and temperature profiles were measured and tested by running liquid nitrogen through the filling manifold. Materials for the inert gas shroud are discussed and experimental results are compared to analytical model predictions. Suggestions for future design improvements are made.

Reversible amorphization and the catalytically active state of crystalline Co3O4 during oxygen evolution.

PubMed

Bergmann, Arno; Martinez-Moreno, Elias; Teschner, Detre; Chernev, Petko; Gliech, Manuel; de Araújo, Jorge Ferreira; Reier, Tobias; Dau, Holger; Strasser, Peter

2015-10-12

Water splitting catalysed by earth-abundant materials is pivotal for global-scale production of non-fossil fuels, yet our understanding of the active catalyst structure and reactivity is still insufficient. Here we report on the structurally reversible evolution of crystalline Co3O4 electrocatalysts during oxygen evolution reaction identified using advanced in situ X-ray techniques. At electrode potentials facilitating oxygen evolution, a sub-nanometre shell of the Co3O4 is transformed into an X-ray amorphous CoOx(OH)y which comprises di-μ-oxo-bridged Co(3+/4+) ions. Unlike irreversible amorphizations, here, the formation of the catalytically-active layer is reversed by re-crystallization upon return to non-catalytic electrode conditions. The Co3O4 material thus combines the stability advantages of a controlled, stable crystalline material with high catalytic activity, thanks to the structural flexibility of its active amorphous oxides. We propose that crystalline oxides may be tailored for generating reactive amorphous surface layers at catalytic potentials, just to return to their stable crystalline state under rest conditions.

Thin Film Ceramic Strain Sensor Development for Harsh Environments: Interim Report on Identification of Candidate Thin Film Ceramics to Test for Viability for Static Strain Sensor Development

NASA Technical Reports Server (NTRS)

Wrbanek, John D.; Fralick, Gustave C.; Hunter, Gary W.

2006-01-01

The need to consider ceramic sensing elements is brought about by the temperature limits of metal thin film sensors in propulsion system applications. In order to have a more passive method of negating changes of resistance due to temperature, an effort is underway at NASA Glenn to develop high temperature thin film ceramic static strain gauges for application in turbine engines, specifically in the fan and compressor modules on blades. Other applications can be on aircraft hot section structures and on thermal protection systems. The near-term interim goal of the research effort was to identify candidate thin film ceramic sensor materials to test for viability and provide a list of possible thin film ceramic sensor materials and corresponding properties to test for viability. This goal was achieved by a thorough literature search for ceramics that have the potential for application as high temperature thin film strain gauges, reviewing potential candidate materials for chemical and physical compatibility with our microfabrication procedures and substrates.

Thin Film Ceramic Strain Sensor Development for Harsh Environments: Identification of Candidate Thin Film Ceramics to Test for Viability for Static Strain Sensor Development

NASA Technical Reports Server (NTRS)

Wrbanek, John D.; Fralick, Gustave C.; Hunter, Gary W.

2006-01-01

The need to consider ceramic sensing elements is brought about by the temperature limits of metal thin film sensors in propulsion system applications. In order to have a more passive method of negating changes of resistance due to temperature, an effort is underway at NASA GRC to develop high temperature thin film ceramic static strain gauges for application in turbine engines, specifically in the fan and compressor modules on blades. Other applications include on aircraft hot section structures and on thermal protection systems. The near-term interim goal of this research effort was to identify candidate thin film ceramic sensor materials to test for viability and provide a list of possible thin film ceramic sensor materials and corresponding properties to test for viability. This goal was achieved by a thorough literature search for ceramics that have the potential for application as high temperature thin film strain gauges, reviewing potential candidate materials for chemical & physical compatibility with NASA GRC's microfabrication procedures and substrates.

Material discovery by combining stochastic surface walking global optimization with a neural network.

PubMed

Huang, Si-Da; Shang, Cheng; Zhang, Xiao-Jie; Liu, Zhi-Pan

2017-09-01

While the underlying potential energy surface (PES) determines the structure and other properties of a material, it has been frustrating to predict new materials from theory even with the advent of supercomputing facilities. The accuracy of the PES and the efficiency of PES sampling are two major bottlenecks, not least because of the great complexity of the material PES. This work introduces a "Global-to-Global" approach for material discovery by combining for the first time a global optimization method with neural network (NN) techniques. The novel global optimization method, named the stochastic surface walking (SSW) method, is carried out massively in parallel for generating a global training data set, the fitting of which by the atom-centered NN produces a multi-dimensional global PES; the subsequent SSW exploration of large systems with the analytical NN PES can provide key information on the thermodynamics and kinetics stability of unknown phases identified from global PESs. We describe in detail the current implementation of the SSW-NN method with particular focuses on the size of the global data set and the simultaneous energy/force/stress NN training procedure. An important functional material, TiO 2 , is utilized as an example to demonstrate the automated global data set generation, the improved NN training procedure and the application in material discovery. Two new TiO 2 porous crystal structures are identified, which have similar thermodynamics stability to the common TiO 2 rutile phase and the kinetics stability for one of them is further proved from SSW pathway sampling. As a general tool for material simulation, the SSW-NN method provides an efficient and predictive platform for large-scale computational material screening.

Application of High-Throughput Seebeck Microprobe Measurements on Thermoelectric Half-Heusler Thin Film Combinatorial Material Libraries.

PubMed

Ziolkowski, Pawel; Wambach, Matthias; Ludwig, Alfred; Mueller, Eckhard

2018-01-08

In view of the variety and complexity of thermoelectric (TE) material systems, combinatorial approaches to materials development come to the fore for identifying new promising compounds. The success of this approach is related to the availability and reliability of high-throughput characterization methods for identifying interrelations between materials structures and properties within the composition spread libraries. A meaningful characterization starts with determination of the Seebeck coefficient as a major feature of TE materials. Its measurement, and hence the accuracy and detectability of promising material compositions, may be strongly affected by thermal and electrical measurement conditions. This work illustrates the interrelated effects of the substrate material, the layer thickness, and spatial property distributions of thin film composition spread libraries, which are studied experimentally by local thermopower scans by means of the Potential and Seebeck Microprobe (PSM). The study is complemented by numerical evaluation. Material libraries of the half-Heusler compound system Ti-Ni-Sn were deposited on selected substrates (Si, AlN, Al 2 O 3 ) by magnetron sputtering. Assuming homogeneous properties of a film, significant decrease of the detected thermopower S m can be expected on substrates with higher thermal conductivity, yielding an underestimation of materials thermopower between 15% and 50%, according to FEM (finite element methods) simulations. Thermally poor conducting substrates provide a better accuracy with thermopower underestimates lower than 8%, but suffer from a lower spatial resolution. According to FEM simulations, local scanning of sharp thermopower peaks on lowly conductive substrates is linked to an additional deviation of the measured thermopower of up to 70% compared to homogeneous films, which is 66% higher than for corresponding cases on substrates with higher thermal conductivity of this study.

Toward identifying specification requirements for digital bone-anchored prosthesis design incorporating substructure fabrication: a pilot study.

PubMed

Eggbeer, Dominic; Bibb, Richard; Evans, Peter

2006-01-01

This paper is the first in a series that aims to identify the specification requirements for advanced digital technologies that may be used to design and fabricate complex, soft tissue facial prostheses. Following a review of previously reported techniques, appropriate and currently available technologies were selected and applied in a pilot study. This study uses a range of optical surface scanning, computerized tomography, computer-aided design, and rapid prototyping technologies to capture, design, and fabricate a bone-anchored auricular prosthesis, including the retentive components. The techniques are assessed in terms of their effectiveness, and the results are used to identify future research and specification requirements to direct developments. The case study identifies that while digital technologies may be used to design implant-retained facial prostheses, many limitations need to be addressed to make the techniques clinically viable. It also identifies the need to develop a more robust specification that covers areas such as resolution, accuracy, materials, and design, against which potential technologies may be assessed. There is a need to develop a specification against which potential technologies may be assessed for their suitability in soft tissue facial prosthetics. The specification will be developed using further experimental research studies.

Using the intranet to deliver patient-education materials.

PubMed

Sorrentino, Catherine; Berger, Ann M; Wardian, Sue; Pattrin, Lynnee M

2002-01-01

Patient education is a critical part of healthcare delivery. Many factors reduce the amount of time nurses can devote to patient teaching. One mode of patient teaching, the use of printed materials, is an efficient and effective way to deliver and reinforce patient education. However, several barriers are associated with the method, including outdated or exhausted supplies of stock materials, expenses related to developing and printing materials, limited storage space, and the inability to locate materials when needed. The authors identified the intranet, an internal network that operates within a larger World Wide Web site, as a potential solution to these barriers. The Outpatient Oncology Clinic and Treatment Center of the Nebraska Health System, a fast-paced care setting in Omaha, agreed to serve as the project pilot area to evaluate using the intranet to generate patient-education materials. Teaching sheets about medication and symptom management, created by the oncology staff, were the first patient-education materials to be made available on the intranet. Advantages of using the intranet for patient education include online storage, decreased costs, easy access, real-time updates and distribution, and unlimited supply availability.

Biomaterial adherent macrophage apoptosis is increased by hydrophilic and anionic substrates in vivo

NASA Astrophysics Data System (ADS)

Brodbeck, William G.; Patel, Jasmine; Voskerician, Gabriela; Christenson, Elizabeth; Shive, Matthew S.; Nakayama, Yasuhide; Matsuda, Takehisa; Ziats, Nicholas P.; Anderson, James M.

2002-08-01

An in vivo rat cage implant system was used to identify potential surface chemistries that prevent failure of implanted biomedical devices and prostheses by limiting monocyte adhesion and macrophage fusion into foreign-body giant cells while inducing adherent-macrophage apoptosis. Hydrophobic, hydrophilic, anionic, and cationic surfaces were used for implantation. Analysis of the exudate surrounding the materials revealed no differences between surfaces in the types or levels of cells present. Conversely, the proportion of adherent cells undergoing apoptosis was increased significantly on anionic and hydrophilic surfaces (46 ± 3.7 and 57 ± 5.0%, respectively) when compared with the polyethylene terephthalate base surface. Additionally, hydrophilic and anionic substrates provided decreased rates of monocyte/macrophage adhesion and fusion. These studies demonstrate that biomaterial-adherent cells undergo material-dependent apoptosis in vivo, rendering potentially harmful macrophages nonfunctional while the surrounding environment of the implant remains unaffected.

High-throughput density functional calculations to optimize properties and interfacial chemistry of piezoelectric materials

NASA Astrophysics Data System (ADS)

Barr, Jordan A.; Lin, Fang-Yin; Ashton, Michael; Hennig, Richard G.; Sinnott, Susan B.

2018-02-01

High-throughput density functional theory calculations are conducted to search through 1572 A B O3 compounds to find a potential replacement material for lead zirconate titanate (PZT) that exhibits the same excellent piezoelectric properties as PZT and lacks both its use of the toxic element lead (Pb) and the formation of secondary alloy phases with platinum (Pt) electrodes. The first screening criterion employed a search through the Materials Project database to find A -B combinations that do not form ternary compounds with Pt. The second screening criterion aimed to eliminate potential candidates through first-principles calculations of their electronic structure, in which compounds with a band gap of 0.25 eV or higher were retained. Third, thermodynamic stability calculations were used to compare the candidates in a Pt environment to compounds already calculated to be stable within the Materials Project. Formation energies below or equal to 100 meV/atom were considered to be thermodynamically stable. The fourth screening criterion employed lattice misfit to identify those candidate perovskites that have low misfit with the Pt electrode and high misfit of potential secondary phases that can be formed when Pt alloys with the different A and B components. To aid in the final analysis, dynamic stability calculations were used to determine those perovskites that have dynamic instabilities that favor the ferroelectric distortion. Analysis of the data finds three perovskites warranting further investigation: CsNb O3 , RbNb O3 , and CsTa O3 .

Solving quantum riddles with neutron scattering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fobes, David M.; Janoschek, Marc

2017-05-16

Quantum materials exhibit a rich landscape of highly-degenerate quantum states that are widely regarded to hold vast potential for future applications, ranging from power management and transmission, to platforms for quantum computation, to novel versatile sensors and electronics. A key to realizing the promise of future applications is to identify the fundamental energy scales that control the emergence of such quantum states and their properties.

Identifying World Views Projected by Science Teaching Materials: A Case Study Using Pepper's WORLD HYPOTHESES to Analyze a Biology Textbook.

ERIC Educational Resources Information Center

Kilbourn, Brent

The purpose of this study is to develop and demonstrate the use of a conceptual framework for assessing the potential of "world view" as a concept for understanding important issues in science education. The framework is based on Stephen C. Pepper's treatment of six world hypotheses (animism, mysticism, formism, mechansim, contextualism, and…

Complete Genome Sequence of Bacillus horikoshii Strain 20a from Cuatro Cienegas, Coahuila, Mexico.

PubMed

Zarza, Eugenia; Alcaraz, Luis D; Aguilar-Salinas, Bernardo; Islas, Africa; Olmedo-Álvarez, Gabriela

2017-07-27

We sequenced the Bacillus horikoshii 20a genome, isolated from sediment collected in Cuatro Cienegas, Mexico. We identified genes involved in establishing antagonistic interactions in microbial communities (antibiotic resistance and bacteriocins) and genes related to the metabolism of cyanophycin, a reserve compound and spore matrix material potentially relevant for survival in an oligotrophic environment. Copyright © 2017 Zarza et al.

Assessment of risk to Boeing commerical transport aircraft from carbon fibers. [fiber release from graphite/epxoy materials

NASA Technical Reports Server (NTRS)

Clarke, C. A.; Brown, E. L.

1980-01-01

The possible effects of free carbon fibers on aircraft avionic equipment operation, removal costs, and safety were investigated. Possible carbon fiber flow paths, flow rates, and transfer functions into the Boeing 707, 727, 737, 747 aircraft and potentially vulnerable equipment were identified. Probabilities of equipment removal and probabilities of aircraft exposure to carbon fiber were derived.

A Linkage Between Parent Materials of Soil and Potential Risk of Heavy Metals in Yunnan province, China

NASA Astrophysics Data System (ADS)

Cheng, X.

2015-12-01

A large area exceeding soil quality standards for heavy metals in South western China has been identified previously reported on a nationwide survey of soil pollution, yet the ecological risk of heavy metal in soil is unknown or uncertainty.To assess thoroughly the ecological risk in this region, seven soil profiles with a depth of 2m on the different parent materials of soil were conducted in Yunnan province, China, and the level of total concentrations and the fraction of water soluble, ion exchangeable, carbonates, humic acid, iron and manganese oxides and organic matter of As, Cd, Hg and Pb was investigated in soil profiles. The results indicate that parent materials of soil critically influenced the ecological risk of heavy metal.The fraction of water soluble and ion exchangeable of Cd and Hg in alluvial material and in terrigenous clastic rocks showed 2-6 times higher than those in carbonate rock; As and Pb has almost same fraction of water soluble and ion exchangeable in three parent materials of soil.The findings suggest that parent materials of soil play a critical role in ecological risk of heavy metal.Thus, more studies are needed to better understand a linkage between the parent materials of soil, different soil-forming processes and the potential risk of heavy metals under various geographic conditions, which is the key for the evaluating soil quality and food safety. Those soils with high concentration of Cd and Hg originated alluvial material and terrigenous clastic rocks need to be continuously monitored before determining a cost-effective remediation technology. Keywords: Heavy metals; Ecological risk;Parent materials of soil;China

Engineering multiple topological phases in nanoscale Van der Waals heterostructures: realisation of α-antimonene

NASA Astrophysics Data System (ADS)

Märkl, T.; Kowalczyk, P. J.; Le Ster, M.; Mahajan, I. V.; Pirie, H.; Ahmed, Z.; Bian, G.; Wang, X.; Chiang, T.-C.; Brown, S. A.

2018-01-01

Van der Waals heterostructures have recently been identified as providing many opportunities to create new two-dimensional materials, and in particular to produce materials with topologically-interesting states. Here we show that it is possible to create such heterostructures with multiple topological phases in a single nanoscale island. We discuss their growth within the framework of diffusion-limited aggregation, the formation of moiré patterns due to the differing crystallographies of the materials comprising the heterostructure, and the potential to engineer both the electronic structure as well as local variations of topological order. In particular we show that it is possible to build islands which include both the hexagonal β- and rectangular α-forms of antimonene, on top of the topological insulator α-bismuthene. This is the first experimental realisation of α-antimonene, and we show that it is a topologically non-trivial material in the quantum spin Hall class.

Review of world experience and properties of materials for encapsulation of terrestrial photovoltaic arrays

NASA Technical Reports Server (NTRS)

Carmichael, D. C.; Gaines, G. B.; Sliemers, F. A.; Kistler, C. W.; Igou, R. D.

1976-01-01

Published and unpublished information relating to encapsulation systems and materials properties was collected by searching the literature and appropriate data bases (over 1,300 documents were selected and reviewed) and by personal contacts including site and company visits. A data tabulation summarizing world experience with terrestrial photovoltaic arrays (50 installations) is presented in the report. Based on criteria of properties, processability, availability, and cost, candidate materials were identified which have potential for use in encapsulation systems for arrays with a lifetime of over 20 years high reliability, an efficiency greater than 10 percent, a total price less than $500/kW, and a production capacity of 500,000 kW/yr. The recommended materials (all commercially available) include, depending upon the device design, various borosilicate and soda-lime glasses and numerous polymerics suitable for specific encapsulation system functions.

Identifying and Reducing Remaining Stocks of Rinderpest Virus

PubMed Central

Visser, Dawid; Evans, Brian; Vallat, Bernard

2015-01-01

In 2011, the world was declared free from rinderpest, one of the most feared and devastating infectious diseases of animals. Rinderpest is the second infectious disease, after smallpox, to have been eradicated. However, potentially infectious rinderpest virus material remains widely disseminated among research and diagnostic facilities across the world and poses a risk for disease recurrence should it be released. Member Countries of the World Organisation for Animal Health and the Food and Agricultural Organization of the United Nations are committed to destroying remaining stocks of infectious material or ensuring that it is stored under international supervision in a limited number of approved facilities. To facilitate this commitment and maintain global freedom from rinderpest, World Organisation for Animal Health Member Countries must report annually on rinderpest material held in their countries. The first official surveys, conducted during 2013–2015, revealed that rinderpest material was stored in an unacceptably high number of facilities and countries. PMID:26584400

Space qualification of silicon carbide for mirror applications: progress and future objectives

NASA Astrophysics Data System (ADS)

Palusinski, Iwona A.; Ghozeil, Isaac

2006-09-01

Production of optical silicon carbide (SiC) for mirror applications continues to evolve and there are renewed plans to use this material in future space-based systems. While SiC has the potential for rapid and cost-effective manufacturing of large, lightweight, athermal optical systems, this material's use in mirror applications is relatively new and has limited flight heritage. This combination of drivers stresses the necessity for a space qualification program for this material. Successful space qualification will require independent collaboration to absorb the high cost of executing this program while taking advantage of each contributing group's laboratory expertise to develop a comprehensive SiC database. This paper provides an overview of the trends and progress in the production of SiC, and identifies future objectives such as non-destructive evaluation and space-effects modeling to ensure proper implementation of this material into future space-based systems.

Gradient Material Strategies for Hydrogel Optimization in Tissue Engineering Applications

PubMed Central

2018-01-01

Although a number of combinatorial/high-throughput approaches have been developed for biomaterial hydrogel optimization, a gradient sample approach is particularly well suited to identify hydrogel property thresholds that alter cellular behavior in response to interacting with the hydrogel due to reduced variation in material preparation and the ability to screen biological response over a range instead of discrete samples each containing only one condition. This review highlights recent work on cell–hydrogel interactions using a gradient material sample approach. Fabrication strategies for composition, material and mechanical property, and bioactive signaling gradient hydrogels that can be used to examine cell–hydrogel interactions will be discussed. The effects of gradients in hydrogel samples on cellular adhesion, migration, proliferation, and differentiation will then be examined, providing an assessment of the current state of the field and the potential of wider use of the gradient sample approach to accelerate our understanding of matrices on cellular behavior. PMID:29485612

Tailoring the thermostability and hydrogen storage capacity of Li decorated carbon materials by heteroatom doping

NASA Astrophysics Data System (ADS)

Long, Jun; Li, Jieyuan; Nan, Fang; Yin, Shi; Li, Jianjun; Cen, Wanglai

2018-03-01

Li decorated graphene is supposed to be a promising material for the hydrogen storage, which can be further improved by heteroatom doping. But a unified promoting mechanism for various doping types and species are still lacking, which hinders the rational design of advanced materials. The potential of N/B doped Li decorated graphene for hydrogen storage is investigated with DFT calculations. A covalent interaction between Li and the graphene substrates is identified to control the thermostability and hydrogen storage capacity (HSC) of the Li decorated substrate, which is in turn subject to the electronegativity of doping species and the doping types. Additionally, a conceptual descriptor is proposed to predict the HSC of Li decorated graphene. These results provide a unified explanation and prediction of the effects of heteroatom doping on Li decorated carbon materials for hydrogen storage.

An Investigation Into The Viability Of Nanocrystalline Cellulose As A Packaging Material

NASA Astrophysics Data System (ADS)

Glass, John

The focus of this proposal is to identify unexplored areas of research in the field of packaging science, specifically related to the incorporation of Nanocrystalline Cellulose (NCC) as a functional material in fiber based packaging, as well as to highlight some of potential risks and unknowns in the product lifecycle. This research hypothesizes that incorporating NCC into wood fiber-based c-flute corrugated packaging medium will show a sufficient performance improvement to justify additional research. Nanomaterials, as a whole, are still being understood, including those using naturally occurring bases such as NCC. Further incremental testing with NCC will help provide a performance and safety baseline for the necessary future research prior to mass production. NCC holds great promise for the future: a commonly available, naturally occurring material that's easily recyclable and biodegradable, yet has the strength of steel. Due diligence is required for this material to come to market in a safe and sustainable manner.

Overview of NRC Proactive Management of Materials Degradation (PMMD) Program

NASA Astrophysics Data System (ADS)

Carpenter, C. E. Gene; Hull, Amy; Oberson, Greg

Materials degradation phenomena, if not appropriately managed, have the potential to adversely impact the design functionality and safety margins of nuclear power plant (NPP) systems, structures and components (SSCs). Therefore, the U.S. Nuclear Regulatory Commission (NRC) has initiated an over-the-horizon multi-year research Proactive Management of Materials Degradation (PMMD) Research Program, which is presently evaluating longer time frames (i.e., 80 or more years) and including passive long-lived SSCs beyond the primary piping and core internals, such as concrete containment and cable insulation. This will allow the NRC to (1) identify significant knowledge gaps and new forms of degradation; (2) capture current knowledge base; and, (3) prioritize materials degradation research needs and directions for future efforts. This effort is being accomplished in collaboration with the U.S. Department of Energy's (DOE) LWR Sustainability (LWRS) program. This presentation will discuss the activities to date, including results, and the path forward.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hernandez, Y.; Carriazo, J.G.; Almanza, O.

Materials from a mining process, in which ferronickel metal extraction is the principal aim, were studied. The residual solid (scum) obtained in this process leads to large-scale accumulation of a vitreous material (pollutant) which creates an environmental problem. These materials were characterized by EPR, X-ray diffraction and X-ray fluorescence. The results indicate that the analyzed solids are rich in Fe{sub 2}O{sub 3} and NiO among other oxides. The scum material shows diffraction signals corresponding to the minerals enstatite (pyroxene) and {alpha}-alumina. Moreover, the scum EPR analysis showed a broad line around g = 2.1 corresponding to Fe{sup 3+} clusters inmore » a complex glassy matrix. An analysis of EPR at different temperatures was also performed. The objective of this work, as a first exploratory stage, is to develop a better understanding of the residual solids in order to identify potential applications.« less

Development of coin-type cell and engineering of its compartments for rechargeable seawater batteries

NASA Astrophysics Data System (ADS)

Han, Jinhyup; Hwang, Soo Min; Go, Wooseok; Senthilkumar, S. T.; Jeon, Donghoon; Kim, Youngsik

2018-01-01

Cell design and optimization of the components, including active materials and passive components, play an important role in constructing robust, high-performance rechargeable batteries. Seawater batteries, which utilize earth-abundant and natural seawater as the active material in an open-structured cathode, require a new platform for building and testing the cells other than typical Li-ion coin-type or pouch-type cells. Herein, we present new findings based on our optimized cell. Engineering the cathode components-improving the wettability of cathode current collector and seawater catholyte flow-improves the battery performance (voltage efficiency). Optimizing the cell component and design is the key to identifying the electrochemical processes and reactions of active materials. Hence, the outcome of this research can provide a systematic study of potentially active materials used in seawater batteries and their effectiveness on the electrochemical performance.

The Alliance of Advanced Process Control and Accountability – A Future Safeguards-By-Design Tool

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lumetta, Gregg J.; Bresee, James C.; Paviet, Patricia D.

For any chemical separation process producing a valuable product, a material balance is an important process control measurement. That is particularly true for the separation of actinides from irradiated nuclear fuel, not only for their intrinsic value but also because an incomplete material balance may indicate diversion for unauthorized use. The DOE Office of Nuclear Energy is currently carrying out at the Pacific Northwest National Laboratory an experimental measurement of how well and with what precision current technologies can implement near real-time actinide material balances. This measurement effort is called the CoDCon project. It involves the separation of a productmore » with a 70/30 uranium/plutonium mass ratio. Initial tests will use dissolved fuel simulants prepared with pure uranium and plutonium nitrates at the same input ratios as irradiated fuel. Subsequent testing with actual irradiated fuel would be done to verify the results obtained with simulants. The experiments will use advanced on-line instrumentation supported by dynamic process models. Since accountability uncertainties could mask diversions, the aim of the project is not only to measure present-day capabilities but also, through sensitivity analyses, to identify those measurements with the greatest potential for overall material-balance improvements. The latter results will help identify priorities for future fuel cycle R&D programs. Advanced separations process control and material accountability technologies thus have a common goal: to provide the best tools available for safeguards-by-design [defined by the International Atomic Energy Agency (IAEA) as the integration of the design of a new nuclear facility through planning, construction, operation and decommissioning]. Since the potential domestic use of CoDCon results may be later than their possible foreign applications, arrangements may be feasible for possible bilateral or multinational cooperation in the CoDCon project.« less

Nuclear Forensics: Report of the AAAS/APS Working Group

NASA Astrophysics Data System (ADS)

Tannenbaum, Benn

2008-04-01

This report was produced by a Working Group of the American Physical Society's Program on Public Affairs in conjunction with the American Association for the Advancement of Science Center for Science, Technology and Security Policy. The primary purpose of this report is to provide the Congress, U.S. government agencies and other institutions involved in nuclear forensics with a clear unclassified statement of the state of the art of nuclear forensics; an assessment of its potential for preventing and identifying unattributed nuclear attacks; and identification of the policies, resources and human talent to fulfill that potential. In the course of its work, the Working Group observed that nuclear forensics was an essential part of the overall nuclear attribution process, which aims at identifying the origin of unidentified nuclear weapon material and, in the event, an unidentified nuclear explosion. A credible nuclear attribution capability and in particular nuclear forensics capability could deter essential participants in the chain of actors needed to smuggle nuclear weapon material or carry out a nuclear terrorist act and could also encourage states to better secure such materials and weapons. The Working Group also noted that nuclear forensics result would take some time to obtain and that neither internal coordination, nor international arrangements, nor the state of qualified personnel and needed equipment were currently enough to minimize the time needed to reach reliable results in an emergency such as would be caused by a nuclear detonation or the intercept of a weapon-size quantity of material. The Working Group assesses international cooperation to be crucial for forensics to work, since the material would likely come from inadequately documented foreign sources. In addition, international participation, if properly managed, could enhance the credibility of the deterrent effect of attribution. Finally the Working Group notes that the U.S. forensics capability involved a number of agencies and other groups that would have to cooperate rapidly in an emergency and that suitable exercises to ensure such cooperation were needed.

Life sciences payload definition and integration study. Volume 1: Management summary

NASA Technical Reports Server (NTRS)

1972-01-01

The objectives of a study program to determine the life sciences payloads required for conducting biomedical experiments during space missions are presented. The objectives are defined as: (1) to identify the research functions which must be performed aboard life sciences spacecraft laboratories and the equipment needed to support these functions and (2) to develop layouts and preliminary conceptual designs of several potential baseline payloads for the accomplishment of life research in space. Payload configurations and subsystems are described and illustrated. Tables of data are included to identify the material requirements for the space missions.

Safety training priorities

NASA Astrophysics Data System (ADS)

Thompson, N. A.; Ruck, H. W.

1984-04-01

The Air Force is interested in identifying potentially hazardous tasks and prevention of accidents. This effort proposes four methods for determining safety training priorities for job tasks in three enlisted specialties. These methods can be used to design training aimed at avoiding loss of people, time, materials, and money associated with on-the-job accidents. Job tasks performed by airmen were measured using task and job factor ratings. Combining accident reports and job inventories, subject-matter experts identified tasks associated with accidents over a 3-year period. Applying correlational, multiple regression, and cost-benefit analysis, four methods were developed for ordering hazardous tasks to determine safety training priorities.

Development of a component design tool for metal hydride heat pumps

NASA Astrophysics Data System (ADS)

Waters, Essene L.

Given current demands for more efficient and environmentally friendly energy sources, hydrogen based energy systems are an increasingly popular field of interest. Within the field, metal hydrides have become a prominent focus of research due to their large hydrogen storage capacity and relative system simplicity and safety. Metal hydride heat pumps constitute one such application, in which heat and hydrogen are transferred to and from metal hydrides. While a significant amount of work has been done to study such systems, the scope of materials selection has been quite limited. Typical studies compare only a few metal hydride materials and provide limited justification for the choice of those few. In this work, a metal hydride component design tool has been developed to enable the targeted down-selection of an extensive database of metal hydrides to identify the most promising materials for use in metal hydride thermal systems. The material database contains over 300 metal hydrides with various physical and thermodynamic properties included for each material. Sub-models for equilibrium pressure, thermophysical data, and default properties are used to predict the behavior of each material within the given system. For a given thermal system, this tool can be used to identify optimal materials out of over 100,000 possible hydride combinations. The selection tool described herein has been applied to a stationary combined heat and power system containing a high-temperature proton exchange membrane (PEM) fuel cell, a hot water tank, and two metal hydride beds used as a heat pump. A variety of factors can be used to select materials including efficiency, maximum and minimum system pressures, pressure difference, coefficient of performance (COP), and COP sensitivity. The targeted down-selection of metal hydrides for this system focuses on the system's COP for each potential pair. The values of COP and COP sensitivity have been used to identify pairs of highest interest for use in this application. The metal hydride component design tool developed in this work selects between metal hydride materials on an unprecedented scale. It can be easily applied to other hydrogen-based thermal systems, making it a powerful and versatile tool.

Evaluation of absorbent materials for use as ad hoc dry decontaminants during mass casualty incidents as part of the UK’s Initial Operational Response (IOR)

PubMed Central

Kassouf, Nick; Syed, Sara; Larner, Joanne; Amlôt, Richard

2017-01-01

The UK’s Initial Operational Response (IOR) is a revised process for the medical management of mass casualties potentially contaminated with hazardous materials. A critical element of the IOR is the introduction of immediate, on-scene disrobing and decontamination of casualties to limit the adverse health effects of exposure. Ad hoc cleansing of the skin with dry absorbent materials has previously been identified as a potential means of facilitating emergency decontamination. The purpose of this study was to evaluate the in vitro oil and water absorbency of a range of materials commonly found in the domestic and clinical environments and to determine the effectiveness of a small, but representative selection of such materials in skin decontamination, using an established ex vivo model. Five contaminants were used in the study: methyl salicylate, parathion, diethyl malonate, phorate and potassium cyanide. In vitro measurements of water and oil absorbency did not correlate with ex vivo measurements of skin decontamination. When measured ex vivo, dry decontamination was consistently more effective than a standard wet decontamination method (“rinse-wipe-rinse”) for removing liquid contaminants. However, dry decontamination was ineffective against particulate contamination. Collectively, these data confirm that absorbent materials such as wound dressings and tissue paper provide an effective, generic capability for emergency removal of liquid contaminants from the skin surface, but that wet decontamination should be used for non-liquid contaminants. PMID:28152053

High-throughput screening of nanoparticle catalysts made by flame spray pyrolysis as hydrocarbon/NO oxidation catalysts.

PubMed

Weidenhof, B; Reiser, M; Stöwe, K; Maier, W F; Kim, M; Azurdia, J; Gulari, E; Seker, E; Barks, A; Laine, R M

2009-07-08

We describe here the use of liquid-feed flame spray pyrolysis (LF-FSP) to produce high surface area, nonporous, mixed-metal oxide nanopowders that were subsequently subjected to high-throughput screening to assess a set of materials for deNO(x) catalysis and hydrocarbon combustion. We were able to easily screen some 40 LF-FSP produced materials. LF-FSP produces nanopowders that very often consist of kinetic rather than thermodynamic phases. Such materials are difficult to access or are completely inaccessible via traditional catalyst preparation methods. Indeed, our studies identified a set of Ce(1-x)Zr(x)O(2) and Al(2)O(3)-Ce(1-x)Zr(x)O(2) nanopowders that offer surprisingly good activities for both NO(x) reduction and propane/propene oxidation both in high-throughput screening and in continuous flow catalytic studies. All of these catalysts offer activities comparable to traditional Pt/Al(2)O(3) catalysts but without Pt. Thus, although Pt-free, they are quite active for several extremely important emission control reactions, especially considering that these are only first generation materials. Indeed, efforts to dope the active catalysts with Pt actually led to lower catalytic activities. Thus the potential exists to completely change the materials used in emission control devices, especially for high-temperature reactions as these materials have already been exposed to 1500 degrees C; however, much research must be done before this potential is verified.

Corrosion Assessment of Candidate Materials for the SHINE Subcritical Assembly Vessel and Components FY15 Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pawel, Steven J.

2016-01-01

In the previous report of this series, a literature review was performed to assess the potential for substantial corrosion issues associated with the proposed SHINE process conditions to produce 99Mo. Following the initial review, substantial laboratory corrosion testing was performed emphasizing immersion and vapor-phase exposure of candidate alloys in a wide variety of solution chemistries and temperatures representative of potential exposure conditions. Stress corrosion cracking was not identified in any of the exposures up to 10 days at 80°C and 10 additional days at 93°C. Mechanical properties and specimen fracture face features resulting from slow-strain rate tests further supported amore » lack of sensitivity of these alloys to stress corrosion cracking. Fluid velocity was found not to be an important variable (0 to ~3 m/s) in the corrosion of candidate alloys at room temperature and 50°C. Uranium in solution was not found to adversely influence potential erosion-corrosion. Potentially intense radiolysis conditions slightly accelerated the general corrosion of candidate alloys, but no materials were observed to exhibit an annualized rate above 10 μm/y.« less

Molecular analysis of long-term biofilm formation on PVC and cast iron surfaces in drinking water distribution system.

PubMed

Liu, Ruyin; Zhu, Junge; Yu, Zhisheng; Joshi, DevRaj; Zhang, Hongxun; Lin, Wenfang; Yang, Min

2014-04-01

To understand the impacts of different plumbing materials on long-term biofilm formation in water supply system, we analyzed microbial community compositions in the bulk water and biofilms on faucets with two different materials-polyvinyl chloride (PVC) and cast iron, which have been frequently used for more than10 years. Pyrosequencing was employed to describe both bacterial and eukaryotic microbial compositions. Bacterial communities in the bulk water and biofilm samples were significantly different from each other. Specific bacterial populations colonized on the surface of different materials. Hyphomicrobia and corrosion associated bacteria, such as Acidithiobacillus spp., Aquabacterium spp., Limnobacter thiooxidans, and Thiocapsa spp., were the most dominant bacteria identified in the PVC and cast iron biofilms, respectively, suggesting that bacterial colonization on the material surfaces was selective. Mycobacteria and Legionella spp. were common potential pathogenic bacteria occurred in the biofilm samples, but their abundance was different in the two biofilm bacterial communities. In contrast, the biofilm samples showed more similar eukaryotic communities than the bulk water. Notably, potential pathogenic fungi, i.e., Aspergillus spp. and Candida parapsilosis, occurred in similar abundance in both biofilms. These results indicated that microbial community, especially bacterial composition was remarkably affected by the different pipe materials (PVC and cast iron). Copyright © 2014 The Research Centre for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

The influence of maternal self-objectification, materialism and parenting style on potentially sexualized 'grown up' behaviours and appearance concerns in 5-8year old girls.

PubMed

Slater, Amy; Tiggemann, Marika

2016-08-01

There is widespread concern about young girls displaying 'grown up' or sexualized behaviours, as well as experiencing body image and appearance concerns that were previously thought to only impact much older girls. The present study examined the influence of three maternal attributes, self-objectification, materialism and parenting style, on sexualized behaviours and appearance concerns in young girls. A sample of 252 Australian mothers of 5-8year old girls reported on the behaviours and appearance concerns observed in their daughters and also completed measures of their own self-objectification, materialism and parenting style. It was found that a significant proportion of young girls were engaging with 'teen' culture, using beauty products and expressing some degree of appearance concern. Maternal self-objectification was related to daughters' engagement in teen culture, use of beauty products and appearance concern. Maternal materialism was related to girls' engagement in teen culture and appearance concern, while an authoritative parenting style was negatively related to girls' use of beauty products. The findings suggest that maternal self-objectification and materialism play a role in the body image and appearance concerns of young girls, and in so doing, identify these maternal attributes as novel potential targets for intervention. Copyright © 2016 Elsevier Ltd. All rights reserved.

Electronic fitness function for screening semiconductors as thermoelectric materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xing, Guangzong; Sun, Jifeng; Li, Yuwei

Here, we introduce a simple but efficient electronic fitness function (EFF) that describes the electronic aspect of the thermoelectric performance. This EFF finds materials that overcome the inverse relationship between σ and S based on the complexity of the electronic structures regardless of specific origin (e.g., isosurface corrugation, valley degeneracy, heavy-light bands mixture, valley anisotropy or reduced dimensionality). This function is well suited for application in high throughput screening. We applied this function to 75 different thermoelectric and potential thermoelectric materials including full- and half-Heuslers, binary semiconductors, and Zintl phases. We find an efficient screening using this transport function. Themore » EFF identifies known high-performance p- and n-type Zintl phases and half-Heuslers. In addition, we find some previously unstudied phases with superior EFF.« less

Investigations of lunar materials

NASA Technical Reports Server (NTRS)

Comstock, G. M.; Fvwaraye, A. O.; Fleischer, R. L.; Hart, H. R., Jr.

1972-01-01

The investigations were directed at determining the radiation history and surface chronology of lunar materials using the etched particle track technique. The major lunar materials studied are the igneous rocks and double core from Apollo 12, the breccia and soil samples from Apollo 14, and the core samples from Luna 16. In the course of this work two new and potentially important observations were made: (1) Cosmic ray-induced spallation-recoil tracks were identified. The density of such tracks, when compared with the density of tracks induced by a known flux of accelerator protons, yields the time of exposure of a sample within the top meter or two of moon's surface. (2) Natural, fine scale plastic deformation was found to have fragmented pre-existing charged particle tracks, allowing the dating of the mechanical event causing the deformation.

Processing of Ni30Pt20Ti50 High-Temperature Shape-Memory Alloy Into Thin Rod Demonstrated

NASA Technical Reports Server (NTRS)

Noebe, Ronald D.; Draper, Susan L.; Biles, Tiffany A.; Leonhardt, Todd

2005-01-01

High-temperature shape-memory alloys (HTSMAs) based on nickel-titanium (NiTi) with significant ternary additions of palladium (Pd), platinum (Pt), gold (Au), or hafnium (Hf) have been identified as potential high-temperature actuator materials for use up to 500 C. These materials provide an enabling technology for the development of "smart structures" used to control the noise, emissions, or efficiency of gas turbine engines. The demand for these high-temperature versions of conventional shape-memory alloys also has been growing in the automotive, process control, and energy industries. However these materials, including the NiPtTi alloys being developed at the NASA Glenn Research Center, will never find widespread acceptance unless they can be readily processed into useable forms.

The early identification of anxiety-laden material with the aid of skin conductance measurements.

PubMed

Lukens, H R

1979-01-01

Measured electrodermal responses (EDR), in the form of changes in skin conductivity, during administration of a calibration questionnaire (CQ) and a personal history questionnaire (PHQ) to each of 25 Ss. "Strong" changes were defined statistically for each S from the amplitudes of EDR evoked by the CQ. The free-floating anxiety of each S also was measured. As predicted on the grounds that questions of the PHQ were more likely than the non-personal questions of the CQ to intersect unresolved, anxiety-laden material, it was found that strong EDR evoked by the PHQ were significantly more likely to perseverate than those evoked by the CQ. Hence, the technique has potential clinical use in identifying anxiety-laden material. Free-floating anxiety did not correlate significantly with EDR data.

Electronic fitness function for screening semiconductors as thermoelectric materials

DOE PAGES

Xing, Guangzong; Sun, Jifeng; Li, Yuwei; ...

2017-11-17

Here, we introduce a simple but efficient electronic fitness function (EFF) that describes the electronic aspect of the thermoelectric performance. This EFF finds materials that overcome the inverse relationship between σ and S based on the complexity of the electronic structures regardless of specific origin (e.g., isosurface corrugation, valley degeneracy, heavy-light bands mixture, valley anisotropy or reduced dimensionality). This function is well suited for application in high throughput screening. We applied this function to 75 different thermoelectric and potential thermoelectric materials including full- and half-Heuslers, binary semiconductors, and Zintl phases. We find an efficient screening using this transport function. Themore » EFF identifies known high-performance p- and n-type Zintl phases and half-Heuslers. In addition, we find some previously unstudied phases with superior EFF.« less

Considerations of technology transfer barriers in the modification of strategic superalloys for aircraft turbine engines

NASA Technical Reports Server (NTRS)

Stephens, J. R.; Tien, J. K.

1983-01-01

A typical innovation-to-commercialization process for the development of a new hot section gas turbine material requires one to two decades with attendant costs in the tens of millions of dollars. This transfer process is examined to determine the potential rate-controlling steps for introduction of future low strategic metal content alloys or processes. Case studies are used to highlight the barriers to commercialization as well as to identify the means by which these barriers can be surmounted. The opportunities for continuing joint government-university-industry partnerships in planning and conducting strategic materials R&D programs are also discussed.

Effects of soil-engineering properties on the failure mode of shallow landslides

USGS Publications Warehouse

McKenna, Jonathan Peter; Santi, Paul Michael; Amblard, Xavier; Negri, Jacquelyn

2012-01-01

Some landslides mobilize into flows, while others slide and deposit material immediately down slope. An index based on initial dry density and fine-grained content of soil predicted failure mode of 96 landslide initiation sites in Oregon and Colorado with 79% accuracy. These material properties can be used to identify potential sources for debris flows and for slides. Field data suggest that loose soils can evolve from dense soils that dilate upon shearing. The method presented herein to predict failure mode is most applicable for shallow (depth 8), with few to moderate fines (fine-grained content <18%), and with liquid limits <40.

Transport suction apparatus and absorption materials evaluation

NASA Technical Reports Server (NTRS)

Krupa, Debra T.; Gosbee, John

1991-01-01

The specific objectives were as follows. The effectiveness and function was evaluated of the hand held, manually powered v-vac for suction during microgravity. The function was evaluated of the battery powered laerdal suction unit in microgravity. The two units in control of various types of simulated bodily fluids were compared. Various types of tubing and attachments were evaluated which are required to control the collection of bodily fluids during transport. Various materials were evaluated for absorption of simulated bodily fluids. And potential problems were identified for waste management and containment of secretions and fluids during transport. Test procedures, results, and conclusions are briefly discussed.

Microgravity Science and Applications Program tasks, 1986 revision

NASA Technical Reports Server (NTRS)

1987-01-01

The Microgravity Science and Applications (MSA) program is directed toward research in the science and technology of processing materials under conditions of low gravity to provide a detailed examination of the constraints imposed by gravitational forces on Earth. The program is expected to lead to the development of new materials and processes in commercial applications adding to this nation's technological base. The research studies emphasize the selected materials and processes that will best elucidate the limitations due to gravity and demonstrate the enhanced sensitivity of control of processes that may be provided by the weightless environment of space. Primary effort is devoted to a study of the specific areas of research which reveals potential value in the initial investigations of the previous decades. Examples of previous process research include crystal growth and directional solidification of metals; containerless processing of reactive materials; synthesis and separation of biological materials; etc. Additional efforts will be devoted to identifying the special requirements which drive the design of hardware to reduce risk in future developments.

Magnetic Phase Diagram of α-RuCl3

NASA Astrophysics Data System (ADS)

Sears, Jennifer; Kim, Young-June; Zhao, Yang; Lynn, Jeffrey

The layered honeycomb material α-RuCl3 is thought to possess unusual magnetic interactions including a strong bond-dependent Kitaev term, offering a potential opportunity to study a material near a well understood spin liquid phase. Although this material orders magnetically at low temperatures and is thus not a realization of a Kitaev spin liquid, it does show a broad continuum of magnetic excitations reminiscent of that expected for the spin liquid phase. It has also been proposed that a magnetic field could destabilize the magnetic order in this material and induce a transition into a spin liquid phase. Low temperature magnetization and specific heat measurements in this material have suggested a complex magnetic phase diagram with multiple unidentified magnetic phases present at low temperature. This has provided motivation for our work characterizing the magnetic transitions and phase diagram in α-RuCl3. I will present detailed bulk measurements combined with magnetic neutron diffraction measurements to map out the phase diagram and identify the various phases present.

Migration from printing inks in multilayer food packaging materials by GC-MS analysis and pattern recognition with chemometrics.

PubMed

Clemente, Isabel; Aznar, Margarita; Nerín, Cristina; Bosetti, Osvaldo

2016-01-01

Inks and varnishes used in food packaging multilayer materials can contain different substances that are potential migrants when packaging is in contact with food. Although printing inks are applied on the external layer, they can migrate due to set-off phenomena. In order to assess food safety, migration tests were performed from two materials sets: set A based on paper and set B based on PET; both contained inks. Migration was performed to four food simulants (EtOH 50%, isooctane, EtOH 95% and Tenax(®)) and the volatile compounds profile was analysed by GC-MS. The effect of presence/absence of inks and varnishes and also their position in the material was studied. A total of 149 volatile compounds were found in migration from set A and 156 from set B materials, some of them came from inks. Quantitative analysis and a principal component analysis were performed in order to identify patterns among sample groups.

Radioactive scrap metal decontamination technology assessment report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buckentin, J.M.; Damkroger, B.K.; Schlienger, M.E.

1996-04-01

Within the DOE complex there exists a tremendous quantity of radioactive scrap metal. As an example, it is estimated that within the gaseous diffusion plants there exists in excess of 700,000 tons of contaminated stainless steel. At present, valuable material is being disposed of when it could be converted into a high quality product. Liquid metal processing represents a true recycling opportunity for this material. By applying the primary production processes towards the material`s decontamination and re-use, the value of the strategic resource is maintained while drastically reducing the volume of material in need of burial. Potential processes for themore » liquid metal decontamination of radioactively contaminated metal are discussed and contrasted. Opportunities and technology development issues are identified and discussed. The processes compared are: surface decontamination; size reduction, packaging and burial; melting technologies; electric arc melting; plasma arc centrifugal treatment; air induction melting; vacuum induction melting; and vacuum induction melting and electroslag remelting.« less

Marine dredged sediments as new materials resource for road construction.

PubMed

Siham, Kamali; Fabrice, Bernard; Edine, Abriak Nor; Patrick, Degrugilliers

2008-01-01

Large volumes of sediments are dredged each year in Europe in order to maintain harbour activities. With the new European Union directives, harbour managers are encouraged to find environmentally sound solutions for these materials. This paper investigates the potential uses of Dunkirk marine dredged sediment as a new material resource for road building. The mineralogical composition of sediments is evaluated using X-ray diffraction and microscopy analysis. Since sediments contain a high amount of water, a dewatering treatment has been used. Different suitable mixtures, checking specific geotechnical criteria as required in French standards, are identified. The mixtures are then optimized for an economical reuse. The mechanical tests conducted on these mixtures are compaction, bearing capacity, compression and tensile tests. The experimental results show the feasibility of the beneficial use of Dunkirk marine dredged sand and sediments as a new material for the construction of foundation and base layers for roads. Further research is now needed to prove the resistance of this new material to various environmental impacts (e.g., frost damage).

Working memory and the design of health materials: a cognitive factors perspective.

PubMed

Wilson, Elizabeth A H; Wolf, Michael S

2009-03-01

Working memory and other supportive cognitive processes involved in learning are reviewed in the context of developing patient education materials. We specifically focus on the impact of certain design factors such as text format and syntax, the inclusion of images, and the choice of modality on individuals' ability to understand and remember health information. A selective review of relevant cognitive and learning theories is discussed with regard to their potential impact on the optimal design of health materials. Working memory is measured as an individual's capacity to hold and manipulate information in active consciousness. It is limited by necessity, and well-designed health materials can effectively minimize extraneous cognitive demands placed on individuals, making working memory resources more available to better process content-related information. Further research is needed to evaluate specific design principles and identify ideal uses of print versus video-based forms of communication for conveying information. The process of developing health materials should account for the cognitive demands that extrinsic factors such as modality place on patients.

Thermal Protection System (Heat Shield) Development - Advanced Development Project

NASA Technical Reports Server (NTRS)

Kowal, T. John

2010-01-01

The Orion Thermal Protection System (TPS) ADP was a 3 1/2 year effort to develop ablative TPS materials for the Orion crew capsule. The ADP was motivated by the lack of available ablative TPS's. The TPS ADP pursued a competitive phased development strategy with succeeding rounds of development, testing and down selections. The Project raised the technology readiness level (TRL) of 8 different TPS materials from 5 different commercial vendors, eventual down selecting to a single material system for the Orion heat shield. In addition to providing a heat shield material and design for Orion on time and on budget, the Project accomplished the following: 1) Re-invigorated TPS industry & re-established a NASA competency to respond to future TPS needs; 2) Identified a potentially catastrophic problem with the planned MSL heat shield, and provided a viable, high TRL alternate heat shield design option; and 3) Transferred mature heat shield material and design options to the commercial space industry, including TPS technology information for the SpaceX Dragon capsule.

Development of leachate test for delayed ettringite formation potential in cementitious materials

NASA Astrophysics Data System (ADS)

France-Mensah, Jojo

Delayed Ettringite Formation (DEF) has been known to be the cause of expansion and cracking at latter ages in concrete that has been heat cured at temperatures around 70 degree Celsius or above. Currently, the only method available for measuring DEF-related physical expansion in concrete can sometimes take over a year to yield relevant results. A leachate method was proposed as a means of taking advantage of the release and solubility of the adsorbed ions (e.g., calcium, sulfates and aluminates) and alkali ions (e.g., sodium and potassium) in the pore solution after heat curing of the cement paste matrix. These ions, known to contribute to DEF, were leached out of concrete into the leaching solution. The results of the leachate test were correlated to physical expansion data of similar samples from an earlier study. The aim of this research is to apply this knowledge to develop an accelerated leachate test method for identifying the potential for DEF in cementitious materials in a shorter time than the existing method. The objectives of this research are: (1) to identify the ion(s) through leaching that is/are the controlling factors in predicting the rate of expansion and overall expansion of mortar; (2) to identify the ion(s) that is/are responsible for the lag time or age of deleterious expansion through DEF; and (3) to investigate the effect of heat curing on the overall, rate of, and age (time) of expansion.

High-throughput screening for thermoelectric sulphides by using crystal structure features as descriptors

NASA Astrophysics Data System (ADS)

Zhang, Ruizhi; Du, Baoli; Chen, Kan; Reece, Mike; Materials Research Insititute Team

With the increasing computational power and reliable databases, high-throughput screening is playing a more and more important role in the search of new thermoelectric materials. Rather than the well established density functional theory (DFT) calculation based methods, we propose an alternative approach to screen for new TE materials: using crystal structural features as 'descriptors'. We show that a non-distorted transition metal sulphide polyhedral network can be a good descriptor for high power factor according to crystal filed theory. By using Cu/S containing compounds as an example, 1600+ Cu/S containing entries in the Inorganic Crystal Structure Database (ICSD) were screened, and of those 84 phases are identified as promising thermoelectric materials. The screening results are validated by both electronic structure calculations and experimental results from the literature. We also fabricated some new compounds to test our screening results. Another advantage of using crystal structure features as descriptors is that we can easily establish structural relationships between the identified phases. Based on this, two material design approaches are discussed: 1) High-pressure synthesis of metastable phase; 2) In-situ 2-phase composites with coherent interface. This work was supported by a Marie Curie International Incoming Fellowship of the European Community Human Potential Program.

Raman spectroscopy method for subsurface detection of food powders through plastic layers

NASA Astrophysics Data System (ADS)

Dhakal, Sagar; Chao, Kuanglin; Qin, Jianwei; Schmidt, Walter F.; Kim, Moon S.; Chan, Diane E.; Bae, Abigail

2017-05-01

Proper chemical analyses of materials in sealed containers are important for quality control purpose. Although it is feasible to detect chemicals at top surface layer, it is relatively challenging to detect objects beneath obscuring surface. This study used spatially offset Raman spectroscopy (SORS) method to detect urea, ibuprofen and acetaminophen powders contained within one or more (up to eight) layers of gelatin capsules to demonstrate subsurface chemical detection and identification. A 785 nm point-scan Raman spectroscopy system was used to acquire spatially offset Raman spectra for an offset range of 0 to 10 mm from the surfaces of 24 encapsulated samples, using a step size of 0.1 mm to obtain 101 spectral measurements per sample. With increasing offset distance, the fraction of information from the deeper subsurface material increased compared to that from the top surface material. The series of measurements was analyzed to differentiate and identify the top surface and subsurface materials. Containing mixed contributions from the powder and capsule, the SORS of each sample was decomposed using self modeling mixture analysis (SMA) to obtain pure component spectra of each component and corresponding components were identified using spectral information divergence values. Results show that SORS technique together with SMA method has a potential for non-invasive detection of chemicals at deep subsurface layer.

Comprehensive summary of beach renourishment and offshore sand removal impacts for Florida

USGS Publications Warehouse

Demopoulos, A.W.J.; Gualtieri, D.J.; Neils, A.; Huge, D.

2011-01-01

An essential first step in the scope of environmental impacts for a sediment mining project is a formulation of specific purpose, precise needs, and estimated impacts. For each individual project, scope must be described, acceptable alternatives must be determined, critical environmental issues must be identified, and mitigation measures must be resolved. Appropriate Federal and State regulations will often require evidence that sand placement is a reasonable alternative to shoreline protection. If so, material to be extracted from the borrow site must be characterized. Candidates must identify the extent of the potential area for sand resources, complete with screening criteria, and site-specific information must be obtained. Alternatives must be identified, compared, and contrasted. And, importantly, the most cost-effective and environmentally sound approach must be determined for the project to move forward. Florida's beaches and coastlines once provided natural protection against storm damage, while simultaneously supporting aquatic ecosystems and both commercial and recreational fisheries. However, beach erosion associated with regional construction and development of the coastline has reduced the effectiveness of natural storm protection. Coastal beaches are, in geological terms, ever-shifting and evolving through natural processes of erosion and replenishment. With permanent structures in place, such as seawalls, jetties, and revetments, natural shoreline is compartmentalized, dynamics are interrupted, and sediment is no longer replenished. Coastal erosion is often a problem where the natural sediment source is deficient. Many of Florida's beaches are now in need of beach replenishment to reduce the high level of damage caused by coastal flooding. Strategic placement of beach fill is a logical means for improving the stability of a shoreline where such a project is economically and environmentally feasible. Sand placement effectively extends the shoreline and provides protection for coastal developments. Beach nourishment or restoration must, however, be thought of as a continual effort and not a one-time fix. Therefore, a combination of sand placement with other erosion mitigation measures can be an effective way to stabilize a shoreline and extend the life of the beach nourishment. Fill material can be obtained from an offshore borrow site, and its characteristics must match the native material in terms of grain size and structure. Environmental concerns for such an effort include potential for decreased water quality during dredging operations, and disturbance of coastal habitat while removing or depositing dredged material. An in-depth scientific evaluation of deposit sites and potential borrow sites must be executed. Mitigation and monitoring efforts will also be critical for a successful low-impact beach management project. The potential exists for unwanted consequences to develop during dredging operations, all of which must be considered and reduced.-->

Evaluation of the potential for debris and hyperconcentrated flows in Capulin Canyon as a result of the 1996 Dome fire, Bandelier National Monument, New Mexico

USGS Publications Warehouse

Cannon, Susan H.

1997-01-01

The Dome fire of April 1996 burned 6684 ha in Bandelier National Monument and the adjacent Sante Fe National Forest. The potential for significant debris- and hyperconcentrated-flow activity in Capulin Canyon is evaluated through 1) a systematic consideration of geologic and geomorphic factors that characterize the condition of the hillslope materials and channels following the fire, 2) examination of sedimentologic evidence for past debris-flow activity in the canyon, and 3) evaluation of the response of the watershed through the 1996 summer monsoon season. The lack of accumulations of dry-ravel material on the hillslopes or in channels, the absence of a continuous hydrophobic layer, the relatively intact condition of the riparian vegetation and of the fibrous root mat on the hillslopes, and the lack of evidence of widespread past debris- and hyperconcentrated-flow activity, even with evidence of past fires, indicate a low potential for debris-flow activity in Capulin Canyon. In addition, thunderstorms during the summer monsoon of 1996 resulted in abundant surface overland flow on the hillslopes which transported low-density pumice, charcoal, ash and some mineral soil downslope as small-scale and non-erosive debris flows. In some places cobble- and boulder-sized material was moved short distances. A moderate potential for debris- and hyperconcentrated-flow activity is identified for the two major tributary canyons to Capulin Canyon based on evidence of both summer of 1996 and possible historic significant debris-flow activity.

Report: Potential environmental impact of exempt site materials - a case study of bituminous road planings and waste soils.

PubMed

Bark, Marjorie; Bland, Michael; Grimes, Sue

2009-09-01

The use of waste materials for ecological benefit, agricultural improvement or as part of construction works are often exempt from waste management control in order to maximize the reuse of material that would otherwise be disposed of to landfill. It is important, however, to determine whether there is potential for such waste to cause environmental harm in the context of the basis for granting exemptions under the relevant framework objective to ensure that waste is recovered or disposed of without risk to water, air, soil, plants or animals. The potential for environmental harm was investigated by leaching studies on two wastes commonly found at exempt sites: bituminous road planings and waste soils. For bituminous road planings, the organic components of the waste were identified by their solubility in organic solvents but these components would have low environmental impact in terms of bioavailability. Leaching studies of the heavy metals copper, lead and zinc, into the environment, under specific conditions and particularly those modelling acid rain and landfill leachate conditions showed that, except for copper, the amounts leached fell within Waste Acceptance Criteria compliance limits for defining waste as inert waste. The fact that the amount of copper leached was greater than the Waste Acceptance Criteria level suggests that either additional testing of wastes regarded as exempt should be carried out to ensure that they are in analytical compliance or that legislation should allow for the potential benefits of reuse to supersede deviations from analytical compliance.

Literature review report on atomistic modeling tools for FeCrAl alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Yongfeng; Schwen, Daniel; Martinez, Enrique

2015-12-01

This reports summarizes the literature review results on atomistic tools, particularly interatomic potentials used in molecular dynamics simulations, for FeCrAl ternary alloys. FeCrAl has recently been identified as a possible cladding concept for accident tolerant fuels for its superior corrosion resistance. Along with several other concepts, an initial evaluation and recommendation are desired for FeCrAl before it’s used in realistic fuels. For this purpose, sufficient understanding on the in-reactor behavior of FeCrAl needs to be grained in a relatively short timeframe, and multiscale modeling and simulations have been selected as an efficient measure to supplement experiments and in-reactor testing formore » better understanding on FeCrAl. For the limited knowledge on FeCrAl alloys, the multiscale modeling approach relies on atomistic simulations to obtain the missing material parameters and properties. As a first step, atomistic tools have to be identified and this is the purpose of the present report. It was noticed during the literature survey that no interatomic potentials currently available for FeCrAl. Here, we summarize the interatomic potentials available for FeCr alloys for possible molecular dynamics studies using FeCr as surrogate materials. Other atomistic methods such as lattice kinetic Monte Carlo are also included in this report. A couple of research topics at the atomic scale are suggested based on the literature survey.« less

Life detection at an Arctic analog to Europa

NASA Astrophysics Data System (ADS)

Gleeson, D. F.; Pappalardo, R. T.; Anderson, M. S.; Grasby, S. E.; Wright, K.; Templeton, A. S.

2010-12-01

Europa is a high priority for astrobiological investigations. Future missions to the icy surface of this moon will query the arguably sulfur-rich materials for potential indications of the presence of life carried to the surface by mobile ice or partial melt. Cold sulfur-rich environments are rare on the Earth, and the potential for the generation and preservation of biosignatures under these conditions remains largely unconstrained. Here we describe investigations into the biogenicity of analogous sulfur deposits from the surface of an Arctic glacier at Borup Fiord pass, Ellesmere Island. Optical and electron microscopy indicate that the sulfur in field samples is present in the form of clumps of mineral grains and spherical mineral aggregates, in close association with microbial sheaths. The morphologies of these materials are consistent with observations of the sulfur generated by sulfide-oxidizing bacteria cultivated from field samples in previous studies. X-ray diffraction measurements provide some evidence for the presence of rosickyite, a metastable form of sulfur previously recognized to be associated with the presence of life. Infrared spectroscopy reveals the presence of organics at parts per million levels, and organic functional groups diagnostic of proteins and fatty acids are identified. Organic components were below the detection limit for Raman spectra, which were dominated by sulfur peaks. These combined investigations indicate that sulfur minerals have the potential to contain identifiable biosignatures that low-temperature conditions help stabilize and preserve. Borup Fiord Pass represents a useful testing ground for instruments and techniques relevant to future astrobiological exploration at Europa.

Physical Diversity of Phyllosilicate Deposits at the MSL Candidate Landing Sites

NASA Astrophysics Data System (ADS)

Fergason, R. L.

2008-12-01

The identification of phyllosilicates on Mars implies aqueous activity at the time of their formation and is important for understanding the history of Martian water and the past habitability of Mars. In addition, a significant fraction of the global water budget of Mars may be locked into clay mineral deposits within the Martian crust. As a result, six out of seven final landing sites being considered for the Mars Science Laboratory are sites where phyllosilicates have been identified in CRISM and OMEGA data. The physical characteristics of these materials, as identified using thermal inertia data, are an important component for understanding the geologic history of these deposits. Thermal inertia values provide information regarding effective particle size and help to constrain the possible presence of duricrust, rocks, and exposed bedrock at these locations. These identified physical characteristics suggest the degree of resistivity to erosion, which has implications for the post-emplacement modification of these deposits. At the aforementioned six locations (Nili Fossae Trough, Holden Crater, Mawrth Vallis, Miyamoto crater, southern Meridiani Planum, and Gale crater) the physical properties were quantified using THEMIS-derived thermal inertia data to characterize the physical properties at each site and identify the presence or absence of physical diversity among these materials. I identified a wide range of surface properties at these locations ranging from indurated surfaces intermixed with unconsolidated aeolian material (thermal inertia of 150-460 J m-2 K-1 s- 1/2) at Mawrth Vallis, to exposures of in-place bedrock and the presence of rocky material (thermal inertia exceeding 800 J m-2 K-1 s-1/2) in Gale crater. In addition, the surface texture and morphologic features observed in high-resolution visible images (such as narrow-angle MOC, HiRISE, and CTX) are dissimilar across these phyllosilicate exposures, and confirm the interpretation of thermal inertia values. The diversity of the physical nature of these materials implies that the environment that deposited phyllosilicates on Mars and their post-emplacement modification is not consistent across all deposits. This result has important implications for the interpretation of their emplacement and subsequent history, and the potential role of water in these regions.

Interdisciplinary Environmental-health Science Throughout Disaster Lifecycles

NASA Astrophysics Data System (ADS)

Plumlee, G. S.; Morman, S. A.; Hoefen, T. M.

2014-12-01

Potential human health effects from exposures to hazardous disaster materials and environmental contamination are common concerns following disasters. Using several examples from US Geological Survey environmental disaster responses (e.g., 2001 World Trade Center, mine tailings spills, 2005 Hurricane Katrina, 2007-2013 wildfires, 2011 Gulf oil spill, 2012 Hurricane Sandy, 2013 Colorado floods) and disaster scenarios (2011 ARkStorm, 2013 SAFRR tsunami) this presentation will illustrate the role for collaborative earth, environmental, and health science throughout disaster lifecycles. Pre-disaster environmental baseline measurements are needed to help understand environmental influences on pre-disaster health baselines, and to constrain the magnitude of a disaster's impacts. During and following disasters, there is a need for interdisciplinary rapid-response and longer-term assessments that: sample and characterize the physical, chemical, and microbial makeup of complex materials generated by the disasters; fingerprint material sources; monitor, map, and model dispersal and evolution of disaster materials in the environment; help understand how the materials are modified by environmental processes; and, identify key characteristics and processes that influence the exposures and toxicity of disaster materials to humans and the living environment. This information helps emergency responders, public health experts, and cleanup managers: 1) identify short- and long-term exposures to disaster materials that may affect health; 2) prioritize areas for cleanup; and 3) develop appropriate disposal solutions or restoration uses for disaster materials. By integrating lessons learned from past disasters with geospatial information on vulnerable sources of natural or anthropogenic contaminants, the environmental health implications of looming disasters or disaster scenarios can be better anticipated, which helps enhance preparedness and resilience. Understanding economic costs of environmental cleanup and environmental-health impacts from disasters is an area of needed research. Throughout all disaster stages, effective communication between diverse scientific disciplines and stakeholder groups is both a necessity and a challenge.

Evaluation of Space Power Materials Flown on the Passive Optical Sample Assembly

NASA Technical Reports Server (NTRS)

Jaworske, Donald A.; deGroh, Kim K.; Skowronski, Timothy J.; McCollum, Tim; Pippin, Gary; Bungay, Corey

1999-01-01

Evaluating the performance of materials on the exterior of spacecraft is of continuing interest, particularly in anticipation of those applications that will require a long duration in low Earth orbit. The Passive Optical Sample Assembly (POSA) experiment flown on the exterior of Mir as a risk mitigation experiment for the International Space Station was designed to better understand the interaction of materials with the low Earth orbit environment and to better understand the potential contamination threats that may be present in the vicinity of spacecraft. Deterioration in the optical performance of candidate space power materials due to the low Earth orbit environment, the contamination environment, or both, must be evaluated in order to propose measures to mitigate such deterioration. The thirty two samples of space power materials studied here include solar array blanket materials such as polyimide Kapton H and SiO(x) coated polyimide Kapton H, front surface aluminized sapphire, solar dynamic concentrator materials such as silver on spin coated polyimide and aluminum on spin coated polyimide, CV 1144 silicone, and the thermal control paint Z-93-P. The physical and optical properties that were evaluated prior to and after the POSA flight include mass, total, diffuse, and specular reflectance, solar absorptance, and infrared emittance. Additional post flight evaluation included scanning electron microscopy to observe surface features caused by the low Earth orbit environment and the contamination environment, and variable angle spectroscopic ellipsometry to identify contaminant type and thickness. This paper summarizes the results of pre- and post-flight measurements, identifies the mechanisms responsible for optical properties deterioration, and suggests improvements for the durability of materials in future missions.

Inorganic Water Repellent Coatings for Thermal Protection Insulation on an Aerospace Vehicle

NASA Technical Reports Server (NTRS)

Fuerstenau, D. W.; Huang, P.; Ravikumar, R.

1997-01-01

The objective of this research was two-fold: first, to identify and test inorganic water-repellent materials that would be hydrophobic even after thermal cycling to temperatures above 600 C and, second, to develop a model that would link hydrophobicity of a material to the chemical properties of its constituent atoms. Four different materials were selected for detailed experimental study, namely, boron nitride, talc, molybdenite, and pyrophyllite, all of which have a layered structure made up of ionic/covalent bonds within the layers but with van der Waals bonds between the layers. The materials tested could be considered hydrophobic for a nonporous surface but none of the observed contact angles exceeded the necessary 90 degrees required for water repellency of porous materials. Boron nitride and talc were observed to retain their water-repellency when heated in air to temperatures that did not exceed 800 C, and molybdenite was found to be retain its hydrophobicity when heated to temperatures up to 600 C. For these three materials, oxidation and decomposition were identified to be the main cause for the breakdown of water repellency after repeated thermal cycling. Pyrophyllite shows the maximum promise as a potential water-repellent inorganic material, which, when treated initially at 900 C, retained its shape and remained hydrophobic for two thermal cycles where the maximum retreatment temperature is 900 C. A model was developed for predicting materials that might exhibit hydrophobicity by linking two chemical properties, namely, that the constituent ions of the compound belong to the soft acid-base category and that the fractional ionic character of the bonds be less than about 20 percent.

Role of slope stability in cumulative impact assessment of hydropower development: North Cascades, Washington

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, R.R.; Staub, W.P.

1993-08-01

Two environmental assessments considered the potential cumulative environmental impacts resulting from the development of eight proposed hydropower projects in the Nooksack River Basin and 11 proposed projects in the Skagit River Basin, North Cascades, Washington, respectively. While not identified as a target resource, slope stability and the alteration of sediment supply to creeks and river mainstems significantly affect other resources. The slope stability assessment emphasized the potential for cumulative impacts under disturbed conditions (e.g., road construction and timber harvesting) and a landslide-induced pipeline rupture scenario. In the case of small-scale slides, the sluicing action of ruptured pipeline water on themore » fresh landslide scarp was found to be capable of eroding significantly more material than the original landslide. For large-scale landslides, sluiced material was found to be a small increment of the original landslide. These results predicted that hypothetical accidental pipeline rupture by small-scale landslides may result in potential cumulative impacts for 12 of the 19 projects with pending license applications in both river basins. 5 refs., 2 tabs.« less

Determination of the mean inner potential of cadmium telluride via electron holography

NASA Astrophysics Data System (ADS)

Cassidy, C.; Dhar, A.; Shintake, T.

2017-04-01

Mean inner potential is a fundamental material parameter in solid state physics and electron microscopy and has been experimentally measured in CdTe, a technologically important semiconductor. As a first step, the inelastic mean free path for electron scattering in CdTe was determined, using electron energy loss spectroscopy, to enable precise thickness mapping of thin CdTe lamellae. The obtained value was λi(CdTe, 300 kV) = 192 ± 10 nm. This value is relatively large, given the high density of the material, and is discussed in the text. Next, electron diffraction and specimen tilting were employed to identify weakly diffracting lattice orientations, to enable the straightforward measurement of the electron phase shift. Finally, electron holography was utilized to quantitatively map the phase shift experienced by electron waves passing through a CdTe crystal, with several different propagation vectors. Utilization of both thickness and phase data allowed computation of mean inner potential as V0 (CdTe) = 14.0 ± 0.9 V, within the range of previous theoretical estimates.

Complete genome sequence provides insights into the biodrying-related microbial function of Bacillus thermoamylovorans isolated from sewage sludge biodrying material.

PubMed

Cai, Lu; Zheng, Sheng-Wei; Shen, Yu-Jun; Zheng, Guo-Di; Liu, Hong-Tao; Wu, Zhi-Ying

2018-07-01

To enable the development of microbial agents and identify suitable candidate used for biodrying, the existence and function of Bacillus thermoamylovorans during sewage sludge biodrying merits investigation. This study isolated a strain of B. thermoamylovorans during sludge biodrying, submitted it for complete genome sequencing and analyzed its potential microbial functions. After biodrying, the moisture content of the biodrying material decreased from 66.33% to 50.18%, and B. thermoamylovorans was the ecologically dominant Bacillus, with the primary annotations associated with amino acid transport and metabolism (9.53%) and carbohydrate transport and metabolism (8.14%). It contains 96 carbohydrate-active- enzyme-encoding gene counts, mainly distributed in glycoside hydrolases (33.3%) and glycosyl transferases (27.1%). The virulence factors are mainly associated with biosynthesis of capsule and polysaccharide capsule. This work indicates that among the biodrying microorganisms, B. thermoamylovorans has good potential for degrading recalcitrant and readily degradable components, thus being a potential microbial agent used to improve biodrying. Copyright © 2018 Elsevier Ltd. All rights reserved.

Titania nanotube arrays as interfaces for blood-contacting implantable devices: a study evaluating the nanotopography-associated activation and expression of blood plasma components.

PubMed

Smith, Barbara S; Popat, Ketul C

2012-08-01

The constant exposure of implantable biomaterials such as titanium and titanium alloys to blood-introducesserious and ongoing concerns regarding poor blood-material interactions. To date, all blood-contacting materials have been shown to initiate immunological events in the form of inflammation, thrombosis, fibrosis and infection; potentially leading to complete implant failure. Material surfaces that provide biomimetic cues such as nanoscale architectures have been shown to elicit improved cellular interaction; and thus, may provide possible solutions for enhancing blood-compatibility. However, limited information exists about the thrombogenicityof nanoscalesurface architectures. In this study, we have evaluated the efficacy of titania nanotube arrays as interfaces for blood contacting devices by investigating the thrombogenic effects using whole blood plasma. Thus, platelet/leukocyte adhesion, activation and interaction, morphology, complement activation, contact activation, platelet release reaction, fibrinogen expression and material cytotoxicity were evaluated to determine the in vitro thrombogenicity. The results presented here indicate a decrease in thrombogenic effects of titania nanotube arrays as compared to biomedical grade titanium after 2 hours of contact with whole blood plasma. This work shows the improved blood-compatibility of titania nanotube arrays, identifying this specific nanoarchitecture as a potentially optimal interface for promoting the long-term success of blood contacting biomaterials.

Removal of sulphur-containing odorants from fuel gases for fuel cell-based combined heat and power applications

NASA Astrophysics Data System (ADS)

de Wild, P. J.; Nyqvist, R. G.; de Bruijn, F. A.; Stobbe, E. R.

Natural gas (NG) and liquefied petroleum gas (LPG) are important potential feedstocks for the production of hydrogen for fuel cell-based (e.g. proton exchange membrane fuel cells (PEMFC) or solid oxide fuel Cells (SOFC) combined heat and power (CHP) applications. To prevent detrimental effects on the (electro)catalysts in fuel cell-based combined heat and power installations (FC-CHP), sulphur removal from the feedstock is mandatory. An experimental bench-marking study of adsorbents has identified several candidates for the removal of sulphur containing odorants at low temperature. Among these adsorbents a new material has been discovered that offers an economically attractive means to remove TetraHydroThiophene (THT), the main European odorant, from natural gas at ambient temperature. The material is environmentally benign, easy to use and possesses good activity (residual sulphur levels below 20 ppbv) and capacity for the common odorant THT in natural gas. When compared to state-of-the-art metal-promoted active carbon the new material has a THT uptake capacity that is up to 10 times larger, depending on temperature and pressure. Promoted versions of the new material have shown potential for the removal of THT at higher temperatures and/or for the removal of other odorants such as mercaptans from natural gas or from LPG.

Flow behavior and mobility of contaminated waste rock materials in the abandoned Imgi mine in Korea

NASA Astrophysics Data System (ADS)

Jeong, S. W.; Wu, Y.-H.; Cho, Y. C.; Ji, S. W.

2018-01-01

Incomplete mine reclamation can cause ecological and environmental impacts. This paper focuses on the geotechnical and rheological characteristics of waste rock materials, which are mainly composed of sand-size particles, potentially resulting in mass movement (e.g., slide or flow) and extensive acid mine drainage. To examine the potential for contaminant mobilization resulting from physicochemical processes in abandoned mines, a series of scenario-based debris flow simulations was conducted using Debris-2D to identify different hazard scenarios and volumes. The flow behavior of waste rock materials was examined using a ball-measuring rheometric apparatus, which can be adapted for large particle samples, such as debris flow. Bingham yield stresses determined in controlled shear rate mode were used as an input parameter in the debris flow modeling. The yield stresses ranged from 100 to 1000 Pa for shear rates ranging from 10- 5 to 102 s- 1. The results demonstrated that the lowest yield stress could result in high mobility of debris flow (e.g., runout distance > 700 m from the source area for 60 s); consequently, the material contaminants may easily reach the confluence of the Suyoung River through a mountain stream. When a fast slide or debris flow occurs at or near an abandoned mine area, it may result in extremely dynamic and destructive geomorphological changes. Even for the highest yield stress of debris flow simulation (i.e., τy = 2000 Pa), the released debris could flow into the mountain stream; therefore, people living near abandoned mines may become exposed to water pollution throughout the day. To maintain safety at and near abandoned mines, the physicochemical properties of waste materials should be monitored, and proper mitigation measures post-mining should be considered in terms of both their physical damage and chemical pollution potential.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, Francis

A team led by GE Global Research developed new magnetic refrigerant materials needed to enhance the commercialization potential of residential appliances such as refrigerators and air conditioners based on the magnetocaloric effect (a nonvapor compression cooling cycle). The new magnetic refrigerant materials have potentially better performance at lower cost than existing materials, increasing technology readiness level. The performance target of the new magnetocaloric material was to reduce the magnetic field needed to achieve 4 °C adiabatic temperature change from 1.5 Tesla to 0.75 Tesla. Such a reduction in field minimizes the cost of the magnet assembly needed for a magneticmore » refrigerator. Such a reduction in magnet assembly cost is crucial to achieving commercialization of magnetic refrigerator technology. This project was organized as an iterative alloy development effort with a parallel material modeling task being performed at George Washington University. Four families of novel magnetocaloric alloys were identified, screened, and assessed for their performance potential in a magnetic refrigeration cycle. Compositions from three of the alloy families were manufactured into regenerator components. At the beginning of the project a previously studied magnetocaloric alloy was selected for manufacturing into the first regenerator component. Each of the regenerators was tested in magnetic refrigerator prototypes at a subcontractor at at GE Appliances. The property targets for operating temperature range, operating temperature control, magnetic field sensitivity, and corrosion resistance were met. The targets for adiabatic temperature change and thermal hysteresis were not met. The high thermal hysteresis also prevented the regenerator components from displaying measurable cooling power when tested in prototype magnetic refrigerators. Magnetic refrigerant alloy compositions that were predicted to have low hysteresis were not attainable with conventional alloy processing methods. Preliminary experiments with rapid solidification methods showed a path towards attaining low hysteresis compositions should this alloy development effort be continued.« less

Nanotechnology patenting trends through an environmental lens: analysis of materials and applications

NASA Astrophysics Data System (ADS)

Leitch, Megan E.; Casman, Elizabeth; Lowry, Gregory V.

2012-12-01

Many international groups study environmental health and safety (EHS) concerns surrounding the use of engineered nanomaterials (ENMs). These researchers frequently use the "Project on Emerging Nanotechnologies" (PEN) inventory of nano-enabled consumer products to prioritize types of ENMs to study because estimates of life-cycle ENM releases to the environment can be extrapolated from the database. An alternative "snapshot" of nanomaterials likely to enter commerce can be determined from the patent literature. The goal of this research was to provide an overview of nanotechnology intellectual property trends, complementary to the PEN consumer product database, to help identify potentially "risky" nanomaterials for study by the nano-EHS community. Ten years of nanotechnology patents were examined to determine the types of nano-functional materials being patented, the chemical compositions of the ENMs, and the products in which they are likely to appear. Patenting trends indicated different distributions of nano-enabled products and materials compared to the PEN database. Recent nanotechnology patenting is dominated by electrical and information technology applications rather than the hygienic and anti-fouling applications shown by PEN. There is an increasing emphasis on patenting of nano-scale layers, coatings, and other surface modifications rather than traditional nanoparticles, and there is widespread use of nano-functional semiconductor, ceramic, magnetic, and biological materials that are currently less studied by EHS professionals. These commonly patented products and the nano-functional materials they contain may warrant life-cycle evaluations to determine the potential for environmental exposure and toxicity. The patent and consumer product lists contribute different and complementary insights into the emerging nanotechnology industry and its potential for introducing nanomaterials into the environment.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mewhinney, J.A.; Bechtold, W.E.; Sun, J.D.

The mission of the Inhalation Toxicology Research Institute is to investigate the nature and magnitude of human health effects that result from the inhalation of airborne materials at home, in the work place, or in the general environment. Diseases of the respiratory tract are major causes of suffering and death, and many of these diseases are directly related to the materials that people breathe. The Institute's research is directed toward obtaining a better understanding of the basic biology of the respiratory tract and the mechanisms by which inhaled materials produce respiratory disease. Special attention is focused on studying the airbornemore » materials released by various energy technologies, as well as those associated with national defense activities. The research uses a wide-ranging, comprehensive array of investigative approaches that are directed toward characterizing the source of the airborne material, following the material through its potential transformation in the air, identifying the mechanisms that govern its inhalation and deposition in the respiratory tract, and determining the fate of these inhaled materials in the body and the health effects they produce. The ultimate objectives are to determine the roles played by inhaled materials in the development of disease processes and to estimate the risk they pose to humans who may be exposed to them.« less

Environmental acceptability of high-performance alternatives for depleted uranium penetrators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kerley, C.R.; Easterly, C.E.; Eckerman, K.F.

1996-08-01

The Army`s environmental strategy for investigating material substitution and management is to measure system environmental gains/losses in all phases of the material management life cycle from cradle to grave. This study is the first in a series of new investigations, applying material life cycle concepts, to evaluate whether there are environmental benefits from increasing the use of tungsten as an alternative to depleted uranium (DU) in Kinetic Energy Penetrators (KEPs). Current military armor penetrators use DU and tungsten as base materials. Although DU alloys have provided the highest performance of any high-density alloy deployed against enemy heavy armor, its low-levelmore » radioactivity poses a number of environmental risks. These risks include exposures to the military and civilian population from inhalation, ingestion, and injection of particles. Depleted uranium is well known to be chemically toxic (kidney toxicity), and workplace exposure levels are based on its renal toxicity. Waste materials containing DU fragments are classified as low-level radioactive waste and are regulated by the Nuclear Regulatory Commission. These characteristics of DU do not preclude its use in KEPs. However, long-term management challenges associated with KEP deployment and improved public perceptions about environmental risks from military activities might be well served by a serious effort to identify, develop, and substitute alternative materials that meet performance objectives and involve fewer environmental risks. Tungsten, a leading candidate base material for KEPS, is potentially such a material because it is not radioactive. Tungsten is less well studied, however, with respect to health impacts and other environmental risks. The present study is designed to contribute to the understanding of the environmental behavior of tungsten by synthesizing available information that is relevant to its potential use as a penetrator.« less

The design and modeling of periodic materials with novel properties

NASA Astrophysics Data System (ADS)

Berger, Jonathan Bernard

Cellular materials are ubiquitous in our world being found in natural and engineered systems as structural materials, sound and energy absorbers, heat insulators and more. Stochastic foams made of polymers, metals and even ceramics find wide use due to their novel properties when compared to monolithic materials. Properties of these so called hybrid materials, those that combine materials or materials and space, are derived from the localization of thermomechanical stresses and strains on the mesoscale as a function of cell topology. The effects of localization can only be generalized in stochastic materials arising from their inherent potential complexity, possessing variations in local chemistry, microstructural inhomogeneity and topological variations. Ordered cellular materials on the other hand, such as lattices and honeycombs, make for much easier study, often requiring analysis of only a single unit-cell. Theoretical bounds predict that hybrid materials have the potential to push design envelopes offering lighter stiffer and stronger materials. Hybrid materials can achieve very low and even negative coefficients of thermal expansion (CTE) while retaining a relatively high stiffness -- properties completely unmatched by monolithic materials. In the first chapter of this thesis a two-dimensional lattice is detailed that possess near maximum stiffness, relative to the tightest theoretical bound, and low, zero and even appreciably negative thermal expansion. Its CTE and stiffness are given in closed form as a function of geometric parameters and the material properties. This result is confirmed with finite elements (FE) and experiment. In the second chapter the compressive stiffness of three-dimensional ordered foams, both closed and open cell, are predicted with FE and the results placed in property space in terms of stiffness and density. A novel structure is identified that effectively achieves theoretical bounds for Young's, shear and bulk modulus simultaneously, over a wide range of relative densities, greatly expanding the property space of available materials with a pragmatic manufacturable structure. A variety of other novel and previously studied ordered foam topologies are also presented that are largely representative of the spectrum of performance of such materials, shedding insight into the behavior of all cellular materials.

A Perspective on Coupled Multiscale Simulation and Validation in Nuclear Materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

M. P. Short; D. Gaston; C. R. Stanek

2014-01-01

The field of nuclear materials encompasses numerous opportunities to address and ultimately solve longstanding industrial problems by improving the fundamental understanding of materials through the integration of experiments with multiscale modeling and high-performance simulation. A particularly noteworthy example is an ongoing study of axial power distortions in a nuclear reactor induced by corrosion deposits, known as CRUD (Chalk River unidentified deposits). We describe how progress is being made toward achieving scientific advances and technological solutions on two fronts. Specifically, the study of thermal conductivity of CRUD phases has augmented missing data as well as revealed new mechanisms. Additionally, the developmentmore » of a multiscale simulation framework shows potential for the validation of a new capability to predict the power distribution of a reactor, in effect direct evidence of technological impact. The material- and system-level challenges identified in the study of CRUD are similar to other well-known vexing problems in nuclear materials, such as irradiation accelerated corrosion, stress corrosion cracking, and void swelling; they all involve connecting materials science fundamentals at the atomistic- and mesoscales to technology challenges at the macroscale.« less

High-Temperature Alloys for Automotive Stirling Engines

NASA Technical Reports Server (NTRS)

Stephens, J. R.; Titran, R. H.

1986-01-01

Stirling engine is external-combustion engine that offers fuel economy, low emissions, low noise, and low vibrations. One of most critical areas in engine development concerns material selection for component parts. Alloys CG-27 and XF-818 identified capable of withstanding rigorous requirements of automotive Stirling engine. Alloys chosen for availability, performance, and manufacturability. Advanced iron-base alloys have potential for variety of applications, including stationary solar-power systems.

Partnering for A Solution: A Case Study

NASA Technical Reports Server (NTRS)

Jimenez-Smith, Deyrah

2003-01-01

A material-related issue has been identified, which has the potential of impacting the Space Program. Although "in-house" efforts have been underway to solve the problem, a solution has not yet been reached. This presentation shows how a GIDEP member organization is using a Problem Advisory as a solution approach in an effort to receive information from other industry and/or government organizations that may contribute in finding a solution.

Clam Shell Dredging in Lakes Pontchartrain and Maurepas, Louisiana. Volume 2. Public Comments.

DTIC Science & Technology

1987-11-01

levels and pattern of distribution of polycyclic aromatic hydrocarbons , is presented, despite the fact that these compounds are identified . . as the...DEIS. Moreover, the DEIS implies that the potential for bioaccumulation of the pollutants present in Lake Ponchartrain is low except for a small...CHEMICAL AIR PRODUCTS SHELL OIL CO SHELL CHEMICAL CIBA GEIGY CORPORATION UNION TEXAS PETROLEUM SAVOIE INDUSTRIES SUNLAND SERVICES VULCAN MATERIAL

Potential Alternatives Report for Validation of Alternatives to Aliphatic Isocyanate Polyurethanes

NASA Technical Reports Server (NTRS)

Lewis, pattie

2011-01-01

Identifying and selecting alternative materials and technologies that have the potential to reduce the identified HazMats and hazardous air pollutants (HAPs), while incorporating sound corrosion prevention and control technologies, is a complicated task due to the fast pace at which new technologies emerge and rules change. The alternatives are identified through literature searches, electronic database and Internet searches, surveys, and/or personal and professional contacts. Available test data was then compiled on the proposed alternatives to determine if the materials meet the test objectives or if further)laboratory or field-testing will be required. After reviewing technical information documented in the PAR, government representatives, technical representatives from the affected facilities, and other stakeholders involved in the process will select the list of viable alternative coatings for consideration and testing under the project's Joint Test Protocol entitled Joint Test Protocol for Validation of Alternatives to Aliphatic Isocyanate Polyurethanes and Field Test Plan entitled Field Evaluations Test Plan for Validation of Alternatives to Aliphatic Isocyanate Polyurethanes, both prepared by ITB. Test results will be reported in a Joint Test Report upon completion oftesting. The selection rationale and conclusions are documented in this PAR. A cost benefit analysis will be prepared to quantify the estimated capital and process costs of coating alternatives and cost savings relative to the current coating processes, however, some initial cost data has been included in this PAR. For this coatings project, isocyanates, as found in aliphatic isocyanate polyurethanes, were identified as the target HazMat to be eliminated. Table 1-1 lists the target HazMats, the related process and application, current specifications, and affected programs.

Chemical characterization and ecotoxicity of three soil foaming agents used in mechanized tunneling.

PubMed

Baderna, Diego; Lomazzi, Eleonora; Passoni, Alice; Pogliaghi, Alberto; Petoumenou, Maria Ifigeneia; Bagnati, Renzo; Lodi, Marco; Viarengo, Aldo; Sforzini, Susanna; Benfenati, Emilio; Fanelli, Roberto

2015-10-15

The construction of tunnels and rocks with mechanized drills produces several tons of rocky debris that are today recycled as construction material or as soil replacement for covering rocky areas. The lack of accurate information about the environmental impact of these excavated rocks and foaming agents added during the excavation process has aroused increasing concern for ecosystems and human health. The present study proposes an integrated approach to the assessment of the potential environmental impact of three foaming agents containing different anionic surfactants and other polymers currently on the market and used in tunnel boring machines. The strategy includes chemical characterization with high resolution mass spectrometry techniques to identify the components of each product, the use of in silico tools to perform a similarity comparison among these compounds and some pollutants already listed in regulatory frameworks to identify possible threshold concentrations of contamination, and the application of a battery of ecotoxicological assays to investigate the impact of each foaming mixture on model organisms of soil (higher plants and Eisenia andrei) and water communities (Daphnia magna). The study identified eleven compounds not listed on the material safety data sheets for which we have identified possible concentrations of contamination based on existing regulatory references. The bioassays allowed us to determine the no effect concentrations (NOAECs) of the three mixtures, which were subsequently used as threshold concentration for the product in its entirety. The technical mixtures used in this study have a different degree of toxicity and the predicted environmental concentrations based on the conditions of use are lower than the NOAEC for soils but higher than the NOAEC for water, posing a potential risk to the waters due to the levels of foaming agents in the muck. Copyright © 2015 Elsevier B.V. All rights reserved.

How important is drinking water exposure for the risks of engineered nanoparticles to consumers?

PubMed

Tiede, Karen; Hanssen, Steffen Foss; Westerhoff, Paul; Fern, Gordon J; Hankin, Steven M; Aitken, Robert J; Chaudhry, Qasim; Boxall, Alistair B A

2016-01-01

This study explored the potential for engineered nanoparticles (ENPs) to contaminate the UK drinking water supplies and established the significance of the drinking water exposure route compared to other routes of human exposure. A review of the occurrence and quantities of ENPs in different product types on the UK market as well as release scenarios, their possible fate and behaviour in raw water and during drinking water treatment was performed. Based on the available data, all the ENPs which are likely to reach water sources were identified and categorized. Worst case concentrations of ENPs in raw water and treated drinking water, using a simple exposure model, were estimated and then qualitatively compared to available estimates for human exposure through other routes. A range of metal, metal oxide and organic-based ENPs were identified that have the potential to contaminate drinking waters. Worst case predicted concentrations in drinking waters were in the low- to sub-µg/l range and more realistic estimates were tens of ng/l or less. For the majority of product types, human exposure via drinking water was predicted to be less important than exposure via other routes. The exceptions were some clothing materials, paints and coatings and cleaning products containing Ag, Al, TiO2, Fe2O3 ENPs and carbon-based materials.

Proteomic analysis of processing by-products from canned and fresh tuna: identification of potentially functional food proteins.

PubMed

Sanmartín, Esther; Arboleya, Juan Carlos; Iloro, Ibon; Escuredo, Kepa; Elortza, Felix; Moreno, F Javier

2012-09-15

Proteomic approaches have been used to identify the main proteins present in processing by-products generated by the canning tuna-industry, as well as in by-products derived from filleting of skeletal red muscle of fresh tuna. Following fractionation by using an ammonium sulphate precipitation method, three proteins (tropomyosin, haemoglobin and the stress-shock protein ubiquitin) were identified in the highly heterogeneous and heat-treated material discarded by the canning-industry. Additionally, this fractionation method was successful to obtain tropomyosin of high purity from the heterogeneous starting material. By-products from skeletal red muscle of fresh tuna were efficiently fractionated to sarcoplasmic and myofibrillar fractions, prior to the identification based mainly on the combined searching of the peptide mass fingerprint (MALDI-TOF) and peptide fragment fingerprinting (MALDI LIFT-TOF/TOF) spectra of fifteen bands separated by 1D SDS-PAGE. Thus, the sarcoplasmic fraction contained myoglobin and several enzymes that are essential for efficient energy production, whereas the myofibrillar fraction had important contractile proteins, such as actin, tropomyosin, myosin or an isoform of the enzyme creatine kinase. Application of proteomic technologies has revealed new knowledge on the composition of important by-products from tuna species, enabling a better evaluation of their potential applications. Copyright © 2012 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brenda R. Pace; Cameron Brizzee; Hollie Gilbert

The U. S. Department of Energy, Idaho Operations Office is considering options for construction of a multipurpose haul road to transport materials and wastes between the Materials and Fuels Complex (MFC) and other Idaho National Laboratory (INL) Site facilities. The proposed road will be closed to the public and designed for limited year-round use. Two primary options are under consideration: a new route south of the existing T-25 power line road and an upgrade to road T-24. In the Spring of 2010, archaeological field surveys and initial coordination and field reconnaissance with representatives from the Shoshone-Bannock Tribes were completed tomore » identify any resources that may be adversely affected by the proposed road construction and to develop recommendations to protect any listed or eligible for listing on the National Register of Historic Places. The investigations showed that 24 archaeological resources and one historic marker are located in the area of potential effects for road construction and operation south of the T-25 powerline road and 27archaeological resources are located in the area of potential effects for road construction and operation along road T-24. Generalized tribal concerns regarding protection of natural resources were also documented in both road corridors. This report outlines recommendations for additional investigations and protective measures that can be implemented to minimize adverse impacts to the identified resources.« less

Direct imaging of defect formation in strained organic flexible electronics by Scanning Kelvin Probe Microscopy

PubMed Central

Cramer, Tobias; Travaglini, Lorenzo; Lai, Stefano; Patruno, Luca; de Miranda, Stefano; Bonfiglio, Annalisa; Cosseddu, Piero; Fraboni, Beatrice

2016-01-01

The development of new materials and devices for flexible electronics depends crucially on the understanding of how strain affects electronic material properties at the nano-scale. Scanning Kelvin-Probe Microscopy (SKPM) is a unique technique for nanoelectronic investigations as it combines non-invasive measurement of surface topography and surface electrical potential. Here we show that SKPM in non-contact mode is feasible on deformed flexible samples and allows to identify strain induced electronic defects. As an example we apply the technique to investigate the strain response of organic thin film transistors containing TIPS-pentacene patterned on polymer foils. Controlled surface strain is induced in the semiconducting layer by bending the transistor substrate. The amount of local strain is quantified by a mathematical model describing the bending mechanics. We find that the step-wise reduction of device performance at critical bending radii is caused by the formation of nano-cracks in the microcrystal morphology of the TIPS-pentacene film. The cracks are easily identified due to the abrupt variation in SKPM surface potential caused by a local increase in resistance. Importantly, the strong surface adhesion of microcrystals to the elastic dielectric allows to maintain a conductive path also after fracture thus providing the opportunity to attenuate strain effects. PMID:27910889

A geological reconnaissance of electrical and electronic waste as a source for rare earth metals.

PubMed

Mueller, Sandra R; Wäger, Patrick A; Widmer, Rolf; Williams, Ian D

2015-11-01

The mining of material resources requires knowledge about geogenic and anthropogenic deposits, in particular on the location of the deposits with the comparatively highest concentration of raw materials. In this study, we develop a framework that allows the establishment of analogies between geological and anthropogenic processes. These analogies were applied to three selected products containing rare earth elements (REE) in order to identify the most concentrated deposits in the anthropogenic cycle. The three identified anthropogenic deposits were characterised according to criteria such as "host rock", "REE mineralisation" and "age of mineralisation", i.e. regarding their "geological" setting. The results of this characterisation demonstrated that anthropogenic deposits have both a higher concentration of REE and a longer mine life than the evaluated geogenic deposit (Mount Weld, Australia). The results were further evaluated by comparison with the geological knowledge category of the United Nations Framework Classification for Fossil Energy and Mineral Reserves and Resources 2009 (UNFC-2009) to determine the confidence level in the deposit quantities. The application of our approach to the three selected cases shows a potential for recovery of REE in anthropogenic deposits; however, further exploration of both potential and limitations is required. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Innovative forming and fabrication technologies : new opportunities.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davis, B.; Hryn, J.; Energy Systems

2008-01-31

The advent of light metal alloys and advanced materials (polymer, composites, etc.) have brought the possibility of achieving important energy reductions into the full life cycle of these materials, especially in transportation applications. 1 These materials have gained acceptance in the aerospace industry but use of light metal alloys needs to gain wider acceptance in other commercial transportation areas. Among the main reasons for the relatively low use of these materials are the lack of manufacturability, insufficient mechanical properties, and increased material costs due to processing inefficiencies. Considering the enormous potential energy savings associated with the use of light metalmore » alloys and advanced materials in transportation, there is a need to identify R&D opportunities in the fields of materials fabrication and forming aimed at developing materials with high specific mechanical properties combined with energy efficient processes and good manufacturability. This report presents a literature review of the most recent developments in the areas of fabrication and metal forming focusing principally on aluminum alloys. In the first section of the document, the different sheet manufacturing technologies including direct chill (DC) casting and rolling, spray forming, spray rolling, thin slab, and strip casting are reviewed. The second section of the document presents recent research on advanced forming processes. The various forming processes reviewed are: superplastic forming, electromagnetic forming, age forming, warm forming, hydroforming, and incremental forming. Optimization of conventional forming processes is also discussed. Potentially interesting light metal alloys for high structural efficiency including aluminum-scandium, aluminum-lithium, magnesium, titanium, and amorphous metal alloys are also reviewed. This section concludes with a discussion on alloy development for manufacturability. The third section of the document reviews the latest developments in fiber-reinforced composite materials. Emerging curing processes are presented along with a discussion on the possible developments in biocomposite materials. The fourth section presents recent developments in the fabrication of bulk nanomaterials and nanoparticles reinforced materials. Advanced joining technologies are presented in the fifth section. Future research is proposed in the last section.« less

Three perspectives on the mismatch between measures of material poverty.

PubMed

Hick, Rod

2015-03-01

The two most prominent measures of material poverty within contemporary European poverty analysis are low income and material deprivation. However, it is by now well-known that these measures identify substantially different people as being poor. In this research note, I seek to demonstrate that there are at least three ways to understand the mismatch between low income and material deprivation, relating to three different forms of identification: identifying poor households, identifying groups at risk of poverty and identifying trends in material poverty over time. Drawing on data from the British Household Panel Survey, I show that while low income and material deprivation identify very different households as being poor, and display distinct trends over time, in many cases they identify the same groups at being at risk of material poverty. © London School of Economics and Political Science 2014.

Low-cost housing design and provision: A case study of Kenya

NASA Astrophysics Data System (ADS)

Kabo, Felichism W.

Shelter is as basic a human need as food and water. Today, many people in Third World countries live in sub-standard housing, or lack shelter altogether. Prior research addresses either one of two housing dimensions: broader provision processes, or specific aspects of design. This dissertation is an effort at addressing both dimensions, the underlying premise being that their inter-connectedness demands an integrative approach. More specifically, this dissertation is a combined strategy case study of housing design and provision in Kenya, a sub-Saharan African country with serious shelter problems. A majority of Kenya's urban population lives in slums or squatter settlements. This dissertation covers four major areas of housing design and provision in Kenya: building materials, user preferences for building materials and housing designs, interior layouts, and the organizational context of the housing sector. These four areas are theoretically unified by Canter's (1977) model of place. Each of the first three areas (housing design) relates to one or more of the three domains in the model. The fourth area (housing provision) pertains to the model's context and framework. The technical building materials research reveals the feasibility of making low-cost materials (soil-cements) with satisfactory engineering performance. The research in preference for building materials reveals that the two independent variables, soil and mix, have a significant effect on potential users' ratings. The housing preference study reveals that of the four independent variables, design and type had a significant effect on potential users' ratings, while materials and construction method did not have a significant effect. The interior layout studies reveal important associations between spatial configurations and a key space (the kitchen), and between configuration and conceptualizations of living, cooking, and sleeping spaces. The findings from the studies of preferences and interior layouts are then synthesized in the development of a low-cost housing prototype. Lastly, analysis of the organizational context reveals notable links between nominal housing-related responsibilities, and the potential power and influence of key organizations. The potential effects of the spatial context on housing organizations are also explored. Later, the key organizations are restructured to address shortcomings identified at the organizational and sectoral levels.

Application of a quality by design approach to the cell culture process of monoclonal antibody production, resulting in the establishment of a design space.

PubMed

Nagashima, Hiroaki; Watari, Akiko; Shinoda, Yasuharu; Okamoto, Hiroshi; Takuma, Shinya

2013-12-01

This case study describes the application of Quality by Design elements to the process of culturing Chinese hamster ovary cells in the production of a monoclonal antibody. All steps in the cell culture process and all process parameters in each step were identified by using a cause-and-effect diagram. Prospective risk assessment using failure mode and effects analysis identified the following four potential critical process parameters in the production culture step: initial viable cell density, culture duration, pH, and temperature. These parameters and lot-to-lot variability in raw material were then evaluated by process characterization utilizing a design of experiments approach consisting of a face-centered central composite design integrated with a full factorial design. Process characterization was conducted using a scaled down model that had been qualified by comparison with large-scale production data. Multivariate regression analysis was used to establish statistical prediction models for performance indicators and quality attributes; with these, we constructed contour plots and conducted Monte Carlo simulation to clarify the design space. The statistical analyses, especially for raw materials, identified set point values, which were most robust with respect to the lot-to-lot variability of raw materials while keeping the product quality within the acceptance criteria. © 2013 Wiley Periodicals, Inc. and the American Pharmacists Association.

Toward a science of learning systems: a research agenda for the high-functioning Learning Health System

PubMed Central

Friedman, Charles; Rubin, Joshua; Brown, Jeffrey; Buntin, Melinda; Corn, Milton; Etheredge, Lynn; Gunter, Carl; Musen, Mark; Platt, Richard; Stead, William; Sullivan, Kevin; Van Houweling, Douglas

2015-01-01

Objective The capability to share data, and harness its potential to generate knowledge rapidly and inform decisions, can have transformative effects that improve health. The infrastructure to achieve this goal at scale—marrying technology, process, and policy—is commonly referred to as the Learning Health System (LHS). Achieving an LHS raises numerous scientific challenges. Materials and methods The National Science Foundation convened an invitational workshop to identify the fundamental scientific and engineering research challenges to achieving a national-scale LHS. The workshop was planned by a 12-member committee and ultimately engaged 45 prominent researchers spanning multiple disciplines over 2 days in Washington, DC on 11–12 April 2013. Results The workshop participants collectively identified 106 research questions organized around four system-level requirements that a high-functioning LHS must satisfy. The workshop participants also identified a new cross-disciplinary integrative science of cyber-social ecosystems that will be required to address these challenges. Conclusions The intellectual merit and potential broad impacts of the innovations that will be driven by investments in an LHS are of great potential significance. The specific research questions that emerged from the workshop, alongside the potential for diverse communities to assemble to address them through a ‘new science of learning systems’, create an important agenda for informatics and related disciplines. PMID:25342177

Dating of rock art and the effect of human activity on vegetation: The complementary use of archaeological and scientific methods

NASA Astrophysics Data System (ADS)

Hjelle, Kari Loe; Lødøen, Trond Klungseth

2017-07-01

One of the main aims of Scandinavian rock art research in recent years has been to identify the culture or society responsible for the imagery. This is of mutual importance, as studies of material culture can shed light on the rock art, while the iconography can be used to understand the contemporary material remains. A major challenge however, has been to determine the exact age of the images, as there are no direct dating materials. In order to overcome this challenge archaeological excavations and palynological analyses have been carried out at Vingen in Western Norway, one of Scandinavia's largest rock art areas. The archaeological and palynological data achieved, as well as loss-on-ignition are independent means for the dating of human activity. Since these methods provided similar results, an indirect connection to the rock art production activity may be inferred. Dates from archaeological contexts indicate a peak of activity between 6900 and 6300 cal. BP, with a potential start 7350 cal. BP and a culmination 6100 cal. BP. Palynological data from three different types of basins have documented forest disturbance in the same time period. Local vegetation reconstructions using the Landscape Reconstruction Algorithm has proved useful to identify anthropogenic-induced land cover changes in the Mesolithic period and a marked reforestation at the transition to the Neolithic period. The applied methods have helped to considerably improve our understanding of past activity and the environment, and demonstrates the potential of archaeological excavations and palynological studies for dating of rock art.

Moving university hydrology education forward with community-based geoinformatics, data and modeling resources

NASA Astrophysics Data System (ADS)

Merwade, V.; Ruddell, B. L.

2012-08-01

In this opinion paper, we review recent literature related to data and modeling driven instruction in hydrology, and present our findings from surveying the hydrology education community in the United States. This paper presents an argument that that data and modeling driven geoscience cybereducation (DMDGC) approaches are essential for teaching the conceptual and applied aspects of hydrology, as a part of the broader effort to improve science, technology, engineering, and mathematics (STEM) education at the university level. The authors have undertaken a series of surveys and a workshop involving university hydrology educators to determine the state of the practice of DMDGC approaches to hydrology. We identify the most common tools and approaches currently utilized, quantify the extent of the adoption of DMDGC approaches in the university hydrology classroom, and explain the community's views on the challenges and barriers preventing DMDGC approaches from wider use. DMDGC approaches are currently emphasized at the graduate level of the curriculum, and only the most basic modeling and visualization tools are in widespread use. The community identifies the greatest barriers to greater adoption as a lack of access to easily adoptable curriculum materials and a lack of time and training to learn constantly changing tools and methods. The community's current consensus is that DMDGC approaches should emphasize conceptual learning, and should be used to complement rather than replace lecture-based pedagogies. Inadequate online material publication and sharing systems, and a lack of incentives for faculty to develop and publish materials via such systems, is also identified as a challenge. Based on these findings, we suggest that a number of steps should be taken by the community to develop the potential of DMDGC in university hydrology education, including formal development and assessment of curriculum materials, integrating lecture-format and DMDGC approaches, incentivizing the publication by faculty of excellent DMDGC curriculum materials, and implementing the publication and dissemination cyberinfrastructure necessary to support the unique DMDGC digital curriculum materials.

Moving university hydrology education forward with geoinformatics, data and modeling approaches

NASA Astrophysics Data System (ADS)

Merwade, V.; Ruddell, B. L.

2012-02-01

In this opinion paper, we review recent literature related to data and modeling driven instruction in hydrology, and present our findings from surveying the hydrology education community in the United States. This paper presents an argument that that Data and Modeling Driven Geoscience Cybereducation (DMDGC) approaches are valuable for teaching the conceptual and applied aspects of hydrology, as a part of the broader effort to improve Science, Technology, Engineering, and Mathematics (STEM) education at the university level. The authors have undertaken a series of surveys and a workshop involving the community of university hydrology educators to determine the state of the practice of DMDGC approaches to hydrology. We identify the most common tools and approaches currently utilized, quantify the extent of the adoption of DMDGC approaches in the university hydrology classroom, and explain the community's views on the challenges and barriers preventing DMDGC approaches from wider use. DMDGC approaches are currently emphasized at the graduate level of the curriculum, and only the most basic modeling and visualization tools are in widespread use. The community identifies the greatest barriers to greater adoption as a lack of access to easily adoptable curriculum materials and a lack of time and training to learn constantly changing tools and methods. The community's current consensus is that DMDGC approaches should emphasize conceptual learning, and should be used to complement rather than replace lecture-based pedagogies. Inadequate online material-publication and sharing systems, and a lack of incentives for faculty to develop and publish materials via such systems, is also identified as a challenge. Based on these findings, we suggest that a number of steps should be taken by the community to develop the potential of DMDGC in university hydrology education, including formal development and assessment of curriculum materials integrating lecture-format and DMDGC approaches, incentivizing the publication by faculty of excellent DMDGC curriculum materials, and implementing the publication and dissemination cyberinfrastructure necessary to support the unique DMDGC digital curriculum materials.

A Typology of Middle School Girls: Audience Segmentation Related to Physical Activity

PubMed Central

Staten, Lisa K.; Birnbaum, Amanda S.; Jobe, Jared B.; Elder, John P.

2008-01-01

The Trial of Activity for Adolescent Girls (TAAG) combines social ecological and social marketing approaches to promote girls’ participation in physical activity programs implemented at 18 middle schools throughout the United States. Key to the TAAG approach is targeting materials to a variety of audience segments. TAAG segments are individuals who share one or more common characteristic that is expected to correlate with physical activity. Thirteen focus groups with seventh and eighth grade girls were conducted to identify and characterize segments. Potential messages and channels of communication were discussed for each segment. Based on participant responses, six primary segments were identified: athletic, preppy, quiet, rebel, smart, and tough. The focus group information was used to develop targeted promotional tools to appeal to a diversity of girls. Using audience segmentation for targeting persuasive communication is potentially useful for intervention programs but may be sensitive; therefore, ethical issues must be critically examined. PMID:16397160

Milan Army Ammunition Plant remedial investigation report: Volume 1. Final report 89-91

DOE Office of Scientific and Technical Information (OSTI.GOV)

Okusu, N.; Hall, H.; Orndorff, A.

1991-12-09

A Remedial Investigation at the Milan Army Ammunition Plant, TN, was conducted for the US Army Toxic and Hazardous Materials Agency, under the terms of an Interagency Agreement with the State of Tennessee and the US Environmental Protection Agency. The study focused on the CERCLA site and selected RCRA regulated units identified by previous studies as potential sources of contamination. A broad range of chemicals including metals, explosives, and other organic compounds were found in source areas and in groundwater. The results of a risk assessment indicate that unacceptable levels of human health risks potentially exist. Conceptual models of sitemore » and unit characteristics were formulated to explain major findings, and areas not contributing to the problem were identified. For many source areas, major unknowns exist regarding hydrology, extent of contamination, and current and future impacts to groundwater quality.« less

A typology of middle school girls: audience segmentation related to physical activity.

PubMed

Staten, Lisa K; Birnbaum, Amanda S; Jobe, Jared B; Elder, John P

2006-02-01

The Trial of Activity for Adolescent Girls (TAAG) combines social ecological and social marketing approaches to promote girls' participation in physical activity programs implemented at 18 middle schools throughout the United States. Key to the TAAG approach is targeting materials to a variety of audience segments. TAAG segments are individuals who share one or more common characteristic that is expected to correlate with physical activity. Thirteen focus groups with seventh and eighth grade girls were conducted to identify and characterize segments. Potential messages and channels of communication were discussed for each segment. Based on participant responses, six primary segments were identified: athletic, preppy, quiet, rebel, smart, and tough. The focus group information was used to develop targeted promotional tools to appeal to a diversity of girls. Using audience segmentation for targeting persuasive communication is potentially useful for intervention programs but may be sensitive; therefore, ethical issues must be critically examined.

Utilizing Societal Concerns in Nanomaterials R and D Decision-Making

NASA Astrophysics Data System (ADS)

Beaver, E. R.

2007-12-01

Nanotechnology has demonstrated the potential to transform many aspects of human existence. From extraordinary ways to deliver pharmaceuticals to the tiniest of electronic circuits to the finest of filters, technologies made with nanomaterials can shrink the computer chip or remove contaminants from water. Nanotechnology systems can deliver drugs to targets inside individual cells or serve as components in sensors that detect chemical and biological agents. As nanomaterials are commercialized, there are potential consequences, both positive and negative. At each stage of development of nanotechnology, it is important to assess both the potential benefits and the potential costs. Scientists need more tools to simultaneously develop new technologies and consider whether their methods or materials might contribute to health or environmental hazards down the line. Early information on potential risks guides the development of these materials as they move toward industrial production. Some indications of problems have turned-up. If thorough assessments are not done, the potential exists to extend projects (and their related expense) long past the point where "fatal flaws" could be identified. As nanotechnology graduates from infancy and it is possible to predict the course and impacts of the technology beyond the next several years. There are well-founded concerns with nanotechnology, especially relating to human health, the environment, and public perception in general. This paper will include a matrix of potential effects, means of ranking or scoring them and examples of how the technique can be applied to current research and development.

Identifying suitable substrates for high-quality graphene-based heterostructures

NASA Astrophysics Data System (ADS)

Banszerus, L.; Janssen, H.; Otto, M.; Epping, A.; Taniguchi, T.; Watanabe, K.; Beschoten, B.; Neumaier, D.; Stampfer, C.

2017-06-01

We report on a scanning confocal Raman spectroscopy study investigating the strain-uniformity and the overall strain and doping of high-quality chemical vapour deposited (CVD) graphene-based heterostuctures on a large number of different substrate materials, including hexagonal boron nitride (hBN), transition metal dichalcogenides, silicon, different oxides and nitrides, as well as polymers. By applying a hBN-assisted, contamination free, dry transfer process for CVD graphene, high-quality heterostructures with low doping densities and low strain variations are assembled. The Raman spectra of these pristine heterostructures are sensitive to substrate-induced doping and strain variations and are thus used to probe the suitability of the substrate material for potential high-quality graphene devices. We find that the flatness of the substrate material is a key figure for gaining, or preserving high-quality graphene.

Varying potential silicon carbide gas sensor

NASA Technical Reports Server (NTRS)

Shields, Virgil B. (Inventor); Ryan, Margaret A. (Inventor); Williams, Roger M. (Inventor)

1997-01-01

A hydrocarbon gas detection device operates by dissociating or electro-chemically oxidizing hydrocarbons adsorbed to a silicon carbide detection layer. Dissociation or oxidation are driven by a varying potential applied to the detection layer. Different hydrocarbon species undergo reaction at different applied potentials so that the device is able to discriminate among various hydrocarbon species. The device can operate at temperatures between 100.degree. C. and at least 650.degree. C., allowing hydrocarbon detection in hot exhaust gases. The dissociation reaction is detected either as a change in a capacitor or, preferably, as a change of current flow through an FET which incorporates the silicon carbide detection layers. The silicon carbide detection layer can be augmented with a pad of catalytic material which provides a signal without an applied potential. Comparisons between the catalytically produced signal and the varying potential produced signal may further help identify the hydrocarbon present.

High-throughput discovery of mutations in tef semi-dwarfing genes by next-generation sequencing analysis.

PubMed

Zhu, Qihui; Smith, Shavannor M; Ayele, Mulu; Yang, Lixing; Jogi, Ansuya; Chaluvadi, Srinivasa R; Bennetzen, Jeffrey L

2012-11-01

Tef (Eragrostis tef) is a major cereal crop in Ethiopia. Lodging is the primary constraint to increasing productivity in this allotetraploid species, accounting for losses of ∼15-45% in yield each year. As a first step toward identifying semi-dwarf varieties that might have improved lodging resistance, an ∼6× fosmid library was constructed and used to identify both homeologues of the dw3 semi-dwarfing gene of Sorghum bicolor. An EMS mutagenized population, consisting of ∼21,210 tef plants, was planted and leaf materials were collected into 23 superpools. Two dwarfing candidate genes, homeologues of dw3 of sorghum and rht1 of wheat, were sequenced directly from each superpool with 454 technology, and 120 candidate mutations were identified. Out of 10 candidates tested, six independent mutations were validated by Sanger sequencing, including two predicted detrimental mutations in both dw3 homeologues with a potential to improve lodging resistance in tef through further breeding. This study demonstrates that high-throughput sequencing can identify potentially valuable mutations in under-studied plant species like tef and has provided mutant lines that can now be combined and tested in breeding programs for improved lodging resistance.

Biomining of MoS2 with Peptide-based Smart Biomaterials.

PubMed

Cetinel, Sibel; Shen, Wei-Zheng; Aminpour, Maral; Bhomkar, Prasanna; Wang, Feng; Borujeny, Elham Rafie; Sharma, Kumakshi; Nayebi, Niloofar; Montemagno, Carlo

2018-02-20

Biomining of valuable metals using a target specific approach promises increased purification yields and decreased cost. Target specificity can be implemented with proteins/peptides, the biological molecules, responsible from various structural and functional pathways in living organisms by virtue of their specific recognition abilities towards both organic and inorganic materials. Phage display libraries are used to identify peptide biomolecules capable of specifically recognizing and binding organic/inorganic materials of interest with high affinities. Using combinatorial approaches, these molecular recognition elements can be converted into smart hybrid biomaterials and harnessed for biotechnological applications. Herein, we used a commercially available phage-display library to identify peptides with specific binding affinity to molybdenite (MoS 2 ) and used them to decorate magnetic NPs. These peptide-coupled NPs could capture MoS 2 under a variety of environmental conditions. The same batch of NPs could be re-used multiple times to harvest MoS 2 , clearly suggesting that this hybrid material was robust and recyclable. The advantages of this smart hybrid biomaterial with respect to its MoS 2 -binding specificity, robust performance under environmentally challenging conditions and its recyclability suggests its potential application in harvesting MoS 2 from tailing ponds and downstream mining processes.

Shadow Formation at Preschool from a Socio-materiality Perspective

NASA Astrophysics Data System (ADS)

Impedovo, Maria Antonietta; Delserieys-Pedregosa, Alice; Jégou, Corinne; Ravanis, Konstantinos

2017-06-01

The paper is set in socio-material farming to offer a way of conceptualising actions and interactions of children in preschool involved in the understanding of scientific concepts. A model of early science education about the physical phenomena of shadow formation is implemented in group work in a French context. The research involved 44 children (13 females and 31 males) of 5-6 years old. The research design was organised in three video recording steps: pre-test, teaching session and post-test. We focus on the analysis of nine teaching sessions to investigate children's `understanding' of shadow formation. A descriptive and qualitative approach was used. In particular, we have identified three main categories (the interaction of the children with the tools, the embodiment and verbal dimension)—with respective indicators—to perform the analysis. From the results, all the categories explored seem to influence each other: all material, human and social dimensions contribute to the children's understanding of shadow formation. Also we have identified some elements that can serve as a potential source of improvement of the teaching session on shadow formation. Finally, the research provides insights on how to improve science activities in preschool with the aim of supporting early understanding of physical phenomena.

The influence of joint technologies on ELV recyclability.

PubMed

Soo, Vi Kie; Compston, Paul; Doolan, Matthew

2017-10-01

Stricter vehicle emission legislation has led to the increasing use of lightweight materials and multi-material concepts to reduce the vehicle mass. To account for the complexity of multi-material vehicle designs, the choice of joining techniques used is becoming more diverse. Moreover, the different material combinations, and their respective joining methods play an important role in determining the potential of full material separation in a closed-loop system. This paper evaluates the types of joining technologies used in the automotive industry, and identifies those that hinder the sorting of ELV materials. The study is based on an industrial shredding trial of car doors. Observations from the case study showed that steel screws and bolts are increasingly used to combine different material types and are less likely to be perfectly liberated during the shredding process. The characteristics of joints that lead to impurities and valuable material losses, such as joint strength, material type, size, diameter, location, and protrusion level, can influence the material liberation in the current sorting practices and thus, lead to ELV waste minimisation. Additionally, the liberation of joints is also affected by the density and thickness of materials being joined. Correlation analyses are carried out to further support the influence of mechanical screws and bolts on material separation efficiencies. The observations are representative of the initial phases of current global ELV sorting practices. Copyright © 2017 Elsevier Ltd. All rights reserved.

Giant thermally-enhanced electrostriction and polar surface phase in L a2M o2O9 oxygen ion conductors

NASA Astrophysics Data System (ADS)

Li, Qian; Lu, Teng; Schiemer, Jason; Laanait, Nouamane; Balke, Nina; Zhang, Zhan; Ren, Yang; Carpenter, Michael A.; Wen, Haidan; Li, Jiangyu; Kalinin, Sergei V.; Liu, Yun

2018-04-01

Ferroelectrics possess spontaneous electric polarization at macroscopic scales which nonetheless imposes strict limitations on the material classes. Recent discoveries of untraditional symmetry-breaking phenomena in reduced material dimensions have indicated feasibilities to extend polar properties to broader types of materials, potentially opening up the freedom for designing materials with hybrid functionalities. Here, we report the unusual electromechanical properties of L a2M o2O9 (LAMOX) oxygen ion conductors, systematically investigated at both bulk and surface length levels. We first observed giant electrostriction effects in L a2M o2O9 bulk ceramics that are thermally enhanced in concert with their low-energy oxygen-vacancy hopping dynamics. Moreover, while no clear bulk polarization was detected, the surface phases of LAMOX were found to be manifestly polar, likely originating from the coupling between the intrinsic structural flexibilities with strain gradients (i.e., flexoelectricity) and/or chemical heterogeneities present in the materials. These findings identify L a2M o2O9 as a promising electromechanical material system and suggest that the flexible structural and chemical configurations in ionically active materials could enable fundamentally different venues to accommodate electric polarization.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ozolins, Vidvuds

Molecularly Engineered Energy Materials (MEEM) was established as an interdisciplinary cutting-edge UCLA-based research center uniquely equipped to attack the challenge of rationally designing, synthesizing and testing revolutionary new energy materials. Our mission was to achieve transformational improvements in the performance of materials via controlling the nano-and mesoscale structure using selectively designed, earth-abundant, inexpensive molecular building blocks. MEEM has focused on materials that are inherently abundant, can be easily assembled from intelligently designed building blocks (molecules, nanoparticles), and have the potential to deliver transformative economic benefits in comparison with the current crystalline-and polycrystalline-based energy technologies. MEEM addressed basic science issues relatedmore » to the fundamental mechanisms of carrier generation, energy conversion, as well as transport and storage of charge and mass in tunable, architectonically complex materials. Fundamental understanding of these processes will enable rational design, efficient synthesis and effective deployment of novel three-dimensional material architectures for energy applications. Three interrelated research directions were initially identified where these novel architectures hold great promise for high-reward research: solar energy generation, electrochemical energy storage, and materials for CO 2 capture. Of these, the first two remained throughout the project performance period, while carbon capture was been phased out in consultation and with approval from BES program manager.« less

Materials trade study for lunar/gateway missions.

PubMed

Tripathi, R K; Wilson, J W; Cucinotta, F A; Anderson, B M; Simonsen, L C

2003-01-01

The National Aeronautics and Space Administration (NASA) administrator has identified protection from radiation hazards as one of the two biggest problems of the agency with respect to human deep space missions. The intensity and strength of cosmic radiation in deep space makes this a 'must solve' problem for space missions. The Moon and two Earth-Moon Lagrange points near Moon are being proposed as hubs for deep space missions. The focus of this study is to identify approaches to protecting astronauts and habitats from adverse effects from space radiation both for single missions and multiple missions for career astronauts to these destinations. As the great cost of added radiation shielding is a potential limiting factor in deep space missions, reduction of mass, without compromising safety, is of paramount importance. The choice of material and selection of the crew profile play major roles in design and mission operations. Material trade studies in shield design over multi-segmented missions involving multiple work and living areas in the transport and duty phase of space mission's to two Earth-Moon co-linear Lagrange points (L1) between Earth and the Moon and (L2) on back side of the moon as seen from Earth, and to the Moon have been studied. It is found that, for single missions, current state-of-the-art knowledge of material provides adequate shielding. On the other hand, the choice of shield material is absolutely critical for career astronauts and revolutionary materials need to be developed for these missions. This study also provides a guide to the effectiveness of multifunctional materials in preparation for more detailed geometry studies in progress. c2003 COSPAR. Published by Elsevier Ltd. All rights reserved.

Effects of Soil Organic Matter Properties and Microbial Community Composition on Enzyme Activities in Cryoturbated Arctic Soils

PubMed Central

Schnecker, Jörg; Wild, Birgit; Hofhansl, Florian; Eloy Alves, Ricardo J.; Bárta, Jiří; Čapek, Petr; Fuchslueger, Lucia; Gentsch, Norman; Gittel, Antje; Guggenberger, Georg; Hofer, Angelika; Kienzl, Sandra; Knoltsch, Anna; Lashchinskiy, Nikolay; Mikutta, Robert; Šantrůčková, Hana; Shibistova, Olga; Takriti, Mounir; Urich, Tim; Weltin, Georg; Richter, Andreas

2014-01-01

Enzyme-mediated decomposition of soil organic matter (SOM) is controlled, amongst other factors, by organic matter properties and by the microbial decomposer community present. Since microbial community composition and SOM properties are often interrelated and both change with soil depth, the drivers of enzymatic decomposition are hard to dissect. We investigated soils from three regions in the Siberian Arctic, where carbon rich topsoil material has been incorporated into the subsoil (cryoturbation). We took advantage of this subduction to test if SOM properties shape microbial community composition, and to identify controls of both on enzyme activities. We found that microbial community composition (estimated by phospholipid fatty acid analysis), was similar in cryoturbated material and in surrounding subsoil, although carbon and nitrogen contents were similar in cryoturbated material and topsoils. This suggests that the microbial community in cryoturbated material was not well adapted to SOM properties. We also measured three potential enzyme activities (cellobiohydrolase, leucine-amino-peptidase and phenoloxidase) and used structural equation models (SEMs) to identify direct and indirect drivers of the three enzyme activities. The models included microbial community composition, carbon and nitrogen contents, clay content, water content, and pH. Models for regular horizons, excluding cryoturbated material, showed that all enzyme activities were mainly controlled by carbon or nitrogen. Microbial community composition had no effect. In contrast, models for cryoturbated material showed that enzyme activities were also related to microbial community composition. The additional control of microbial community composition could have restrained enzyme activities and furthermore decomposition in general. The functional decoupling of SOM properties and microbial community composition might thus be one of the reasons for low decomposition rates and the persistence of 400 Gt carbon stored in cryoturbated material. PMID:24705618

Marketing HIV prevention for heterosexually identified Latino men who have sex with men and women: the Hombres Sanos campaign.

PubMed

Fernández Cerdeño, Araceli; Martínez-Donate, Ana P; Zellner, Jennifer A; Sañudo, Fernando; Carrillo, Héctor; Engelberg, Moshe; Sipan, Carol; Hovell, Melbourne

2012-01-01

This article describes the development process of Hombres Sanos, a social marketing campaign to promote HIV testing and condom use for heterosexually identified Latino men who have sex with men and women. The steps included qualitative formative research and a social marketing analytic framework to understand our target audience better, identify incentives and barriers to risk reduction, guide product development, define an optimal promotional campaign, and inform the selection of campaign platforms. A better grasp of the authors' target beneficiaries' needs and values led to an innovative dual strategy for audience segmentation and targeting. The campaign had consumer-centered, culturally sensitive, and theory-driven communication materials. The authors found communication materials and events to be appealing and effective. The campaign was well received among the wider community, and evaluation showed promising results among Latino men in general and among heterosexually identified Latino men who have sex with men and women in particular. The authors provide a step-by-step overview of the project's formative research, including research methods and findings, and how these were translated into a social marketing campaign. In addition, the authors discuss the challenges encountered in this process and the potential of social marketing to reduce HIV risk among Latinos.

Identification of wood-boring beetles (Cerambycidae and Buprestidae) intercepted in trade-associated solid wood packaging material using DNA barcoding and morphology.

PubMed

Wu, Yunke; Trepanowski, Nevada F; Molongoski, John J; Reagel, Peter F; Lingafelter, Steven W; Nadel, Hannah; Myers, Scott W; Ray, Ann M

2017-01-16

Global trade facilitates the inadvertent movement of insect pests and subsequent establishment of populations outside their native ranges. Despite phytosanitary measures, nonnative insects arrive at United States (U.S.) ports of entry as larvae in solid wood packaging material (SWPM). Identification of wood-boring larval insects is important for pest risk analysis and management, but is difficult beyond family level due to highly conserved morphology. Therefore, we integrated DNA barcoding and rearing of larvae to identify wood-boring insects in SWPM. From 2012 to 2015, we obtained larvae of 338 longhorned beetles (Cerambycidae) and 38 metallic wood boring beetles (Buprestidae) intercepted in SWPM associated with imported products at six U.S. ports. We identified 265 specimens to species or genus using DNA barcodes. Ninety-three larvae were reared to adults and identified morphologically. No conflict was found between the two approaches, which together identified 275 cerambycids (23 genera) and 16 buprestids (4 genera). Our integrated approach confirmed novel DNA barcodes for seven species (10 specimens) of woodborers not in public databases. This study demonstrates the utility of DNA barcoding as a tool for regulatory agencies. We provide important documentation of potential beetle pests that may cross country borders through the SWPM pathway.

Identification of wood-boring beetles (Cerambycidae and Buprestidae) intercepted in trade-associated solid wood packaging material using DNA barcoding and morphology

PubMed Central

Wu, Yunke; Trepanowski, Nevada F.; Molongoski, John J.; Reagel, Peter F.; Lingafelter, Steven W.; Nadel, Hannah; Myers, Scott W.; Ray, Ann M.

2017-01-01

Global trade facilitates the inadvertent movement of insect pests and subsequent establishment of populations outside their native ranges. Despite phytosanitary measures, nonnative insects arrive at United States (U.S.) ports of entry as larvae in solid wood packaging material (SWPM). Identification of wood-boring larval insects is important for pest risk analysis and management, but is difficult beyond family level due to highly conserved morphology. Therefore, we integrated DNA barcoding and rearing of larvae to identify wood-boring insects in SWPM. From 2012 to 2015, we obtained larvae of 338 longhorned beetles (Cerambycidae) and 38 metallic wood boring beetles (Buprestidae) intercepted in SWPM associated with imported products at six U.S. ports. We identified 265 specimens to species or genus using DNA barcodes. Ninety-three larvae were reared to adults and identified morphologically. No conflict was found between the two approaches, which together identified 275 cerambycids (23 genera) and 16 buprestids (4 genera). Our integrated approach confirmed novel DNA barcodes for seven species (10 specimens) of woodborers not in public databases. This study demonstrates the utility of DNA barcoding as a tool for regulatory agencies. We provide important documentation of potential beetle pests that may cross country borders through the SWPM pathway. PMID:28091577

Application of composites to the selective reinforcement of metallic aerospace structures. [application of structural design criteria for weight reduction

NASA Technical Reports Server (NTRS)

Brooks, W. A., Jr.; Mathauser, E. E.; Pride, R. A.

1972-01-01

The use of composite materials to selectively reinforce metallic structures provides a low-cost way to reduce weight and a means of minimizing the risks usually associated with the introduction of new materials. An overview is presented of the NASA Langley Research Center programs to identify the advantages and to develop the potential of the selective reinforcement approach to the use of composites. These programs have shown that selective reinforcement provides excellent strength and stiffness improvements to metallic structures. Significant weight savings can be obtained in a cost effective manner. Flight service programs which have been initiated to validate further the merits of selective reinforcement are described.

Investigations on composites reinforced with HEA particles

NASA Astrophysics Data System (ADS)

Carcea, I.; Chelariu, R.; Asavei, L.; Cimpoeşu, N.; Florea, R. M.

2017-08-01

This work reports the results of investigations on the fortification with high entropy alloys particles of aluminium matrix composite materials. The properties of these materials processed by Vortex techniques primarily depend on the matrix and the volume fraction of the constituent phase. The mechanical properties, toughening mechanisms and potential applications are briefly reviewed. Traditional methods were used for the basic characterization of the composite. The microstructure of the composites were investigated by optical and scanning electron microscopy (OM, SEM). SEM analysis was performed in order to observe the microstructural evolution as a function of the HEA particles content and to identify some reasons of the presence of porosity or any irregularities within the metal matrix.

Tungsten fiber reinforced FeCralY: A first generation composite turbine blade material

NASA Technical Reports Server (NTRS)

Petrasek, D. W.; Winsa, E. A.; Westfall, L. J.; Signorelli, R. A.

1979-01-01

Tungsten-fiber/FeCrAlY (W/FeCrAlY) was identified as a promising aircraft engine, first generation, turbine blade composite material. Based on available data, W/FeCrAlY should have the stress-rupture, creep, tensile, fatigue, and impact strengths required for turbine blades operating from 1250 to 1370 K. It should also have adequate oxidation, hot corrosion, and thermal cycling damage resistance as well as high thermal conductivity. Concepts for potentially low cost blade fabrication were developed. These concepts were used to design a first stage JT9D convection cooled turbine blade having a calculated 50 K use-temperature advantage over the directionally solidified superalloy blade.

Rapid on-site detection of airborne asbestos fibers and potentially hazardous nanomaterials using fluorescence microscopy-based biosensing.

PubMed

Kuroda, Akio; Alexandrov, Maxym; Nishimura, Tomoki; Ishida, Takenori

2016-06-01

A large number of peptides with binding affinity to various inorganic materials have been identified and used as linkers, catalysts, and building blocks in nanotechnology and nanobiotechnology. However, there have been few applications of material-binding peptides in the fluorescence microscopy-based biosensing (FM method) of environmental pollutants. A notable exception is the application of the FM method for the detection of asbestos, a dangerous industrial toxin that is still widely used in many developing countries. This review details the selection and isolation of asbestos-binding proteins and peptides with sufficient specificity to distinguish asbestos from a large variety of safer fibrous materials used as asbestos substitutes. High sensitivity to nanoscale asbestos fibers (30-35 nm in diameter) invisible under conventional phase contrast microscopy can be achieved. The FM method is the basis for developing an automated system for asbestos biosensing that can be used for on-site testing with a portable fluorescence microscope. In the future, the FM method could also become a useful tool for detecting other potentially hazardous nanomaterials in the environment. Copyright © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Micro-engineered first wall tungsten armor for high average power laser fusion energy systems

NASA Astrophysics Data System (ADS)

Sharafat, Shahram; Ghoniem, Nasr M.; Anderson, Michael; Williams, Brian; Blanchard, Jake; Snead, Lance; HAPL Team

2005-12-01

The high average power laser program is developing an inertial fusion energy demonstration power reactor with a solid first wall chamber. The first wall (FW) will be subject to high energy density radiation and high doses of high energy helium implantation. Tungsten has been identified as the candidate material for a FW armor. The fundamental concern is long term thermo-mechanical survivability of the armor against the effects of high temperature pulsed operation and exfoliation due to the retention of implanted helium. Even if a solid tungsten armor coating would survive the high temperature cyclic operation with minimal failure, the high helium implantation and retention would result in unacceptable material loss rates. Micro-engineered materials, such as castellated structures, plasma sprayed nano-porous coatings and refractory foams are suggested as a first wall armor material to address these fundamental concerns. A micro-engineered FW armor would have to be designed with specific geometric features that tolerate high cyclic heating loads and recycle most of the implanted helium without any significant failure. Micro-engineered materials are briefly reviewed. In particular, plasma-sprayed nano-porous tungsten and tungsten foams are assessed for their potential to accommodate inertial fusion specific loads. Tests show that nano-porous plasma spray coatings can be manufactured with high permeability to helium gas, while retaining relatively high thermal conductivities. Tungsten foams where shown to be able to overcome thermo-mechanical loads by cell rotation and deformation. Helium implantation tests have shown, that pulsed implantation and heating releases significant levels of implanted helium. Helium implantation and release from tungsten was modeled using an expanded kinetic rate theory, to include the effects of pulsed implantations and thermal cycles. Although, significant challenges remain micro-engineered materials are shown to constitute potential candidate FW armor materials.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Jie; Viengkham, Malathong; Bertozzi, Carolyn R.

The controlled integration of organic and inorganic components confers natural bone with superior mechanical properties. Bone biogenesis is thought to occur by templated mineralization of hard apatite crystals by an elastic protein scaffold, a process we sought to emulate with synthetic biomimetic hydrogel polymers. Crosslinked polymethacrylamide and polymethacrylate hydrogels were functionalized with mineral-binding ligands and used to template the formation of hydroxyapatite. Strong adhesion between the organic and inorganic materials was achieved for hydrogels functionalized with either carboxylate or hydroxy ligands. The mineral-nucleating potential of hydroxyl groups identified here broadens the design parameters for synthetic bone-like composites and suggests amore » potential role for hydroxylated collagen proteins in bone mineralization.« less

Environmental Control and Life Support (ECLS) Hardware Commonality for Exploration Vehicles

NASA Technical Reports Server (NTRS)

Carrasquillo, Robyn; Anderson, Molly

2012-01-01

In August 2011, the Environmental Control and Life Support Systems (ECLSS) technical community, along with associated stakeholders, held a workshop to review NASA s plans for Exploration missions and vehicles with two objectives: revisit the Exploration Atmospheres Working Group (EAWG) findings from 2006, and discuss preliminary ECLSS architecture concepts and technology choices for Exploration vehicles, identifying areas for potential common hardware or technologies to be utilized. Key considerations for selection of vehicle design total pressure and percent oxygen include operational concepts for extravehicular activity (EVA) and prebreathe protocols, materials flammability, and controllability within pressure and oxygen ranges. New data for these areas since the 2006 study were presented and discussed, and the community reached consensus on conclusions and recommendations for target design pressures for each Exploration vehicle concept. For the commonality study, the workshop identified many areas of potential commonality across the Exploration vehicles as well as with heritage International Space Station (ISS) and Shuttle hardware. Of the 36 ECLSS functions reviewed, 16 were considered to have strong potential for commonality, 13 were considered to have some potential commonality, and 7 were considered to have limited potential for commonality due to unique requirements or lack of sufficient heritage hardware. These findings, which will be utilized in architecture studies and budget exercises going forward, are presented in detail.

A Direct Mechanism of Ultrafast Intramolecular Singlet Fission in Pentacene Dimers

DTIC Science & Technology

2016-08-24

property for materials used in third- generation solar cells and photodetectors, among other optoelectronic devices.1−3 Unfortunately, techno- logical...detailed mechanism of iSF and to establish its relationship to chemical structure. Current literature on the mechanism of xSF is in general agreement...not been identified. We use this ring-breathing mode to generate a two- dimensional potential energy surface (PES) for the excited states along the

Eco-Efficient Process Improvement at the Early Development Stage: Identifying Environmental and Economic Process Hotspots for Synergetic Improvement Potential.

PubMed

Piccinno, Fabiano; Hischier, Roland; Seeger, Stefan; Som, Claudia

2018-05-15

We present here a new eco-efficiency process-improvement method to highlight combined environmental and costs hotspots of the production process of new material at a very early development stage. Production-specific and scaled-up results for life cycle assessment (LCA) and production costs are combined in a new analysis to identify synergetic improvement potentials and trade-offs, setting goals for the eco-design of new processes. The identified hotspots and bottlenecks will help users to focus on the relevant steps for improvements from an eco-efficiency perspective and potentially reduce their associated environmental impacts and production costs. Our method is illustrated with a case study of nanocellulose. The results indicate that the production route should start with carrot pomace, use heat and solvent recovery, and deactivate the enzymes with bleach instead of heat. To further improve the process, the results show that focus should be laid on the carrier polymer, sodium alginate, and the production of the GripX coating. Overall, the method shows that the underlying LCA scale-up framework is valuable for purposes beyond conventional LCA studies and is applicable at a very early stage to provide researchers with a better understanding of their production process.

Creating the 2020 Tokyo Olympic Medals from Electronic Scrap: Sustainability Analysis

NASA Astrophysics Data System (ADS)

Leader, Alexandra M.; Wang, Xue; Gaustad, Gabrielle

2017-09-01

For the upcoming 2020 Olympic Games, which are to be held in Tokyo, Japan, it has been proposed that recycled metal from electronic waste should be used to create the gold, silver, and bronze medals that will be awarded to athletes from around the world. This work is aimed at exploring the feasibility of this goal, quantifying the required electronic waste, identifying the limiting material constraints, and addressing a selection of sustainability metrics. The results show that 2.5-13.8% of Japan's available electronic waste would be required to create the medals, depending on the composition of the collected electronics and the processing yields. The environmental benefits from this venture are identified as being a savings of approximately 4.5-5.1 TJ of energy, which is equivalent to CO2 emissions reductions of approximately 420 metric tons. Additionally, qualitative potential benefits to environment, human health, economic recovery of valuable materials, and supply stability are considered.

Relationship between bacterial diversity and environmental parameters during composting of different raw materials.

PubMed

Wang, Xueqin; Cui, Hongyang; Shi, Jianhong; Zhao, Xinyu; Zhao, Yue; Wei, Zimin

2015-12-01

The aim of this study was to compare the bacterial structure of seven different composts. The primary environmental factors affecting bacterial species were identified, and a strategy to enhance the abundance of uncultured bacteria through controlling relevant environmental parameters was proposed. The results showed that the physical-chemical parameters of each different pile changed in its own manner during composting, which affected the structure and succession of bacteria in different ways. DGGE profiles showed that there were 10 prominent species during composting. Among them, four species existed in all compost types, two species existed in several piles and four species were detected in a single material. Redundancy analysis results showed that bacterial species compositions were significantly influenced by C/N and moisture (p<0.05). The optimal range of C/N was 14-27. Based on these results, the primary environmental factors affecting a certain species were further identified as a potential control of bacterial diversity. Copyright © 2015 Elsevier Ltd. All rights reserved.

Distance learning--an educational tool for developing countries.

PubMed

Dobson, M B

2000-01-01

Many anaesthetists in small hospitals and developing countries have poor access to educational materials. The use of electronic means of publication and distribution, combined with the concepts of distance learning, can lead to better levels of knowledge and clinical practice. A project based on these principles has been set up in Zimbabwe, and is proving helpful to both trainers and trainees. All District Hospitals have been visited, and trainees in them identified. A survey has been completed to identify the subject areas in which training is most necessary. Trainees have been provided with reference materials on CD-ROM which they can access by computer (each hospital has a computer). Specialist anaesthesiologists in the country are producing interactive tutorials which can be sent out by e-mail to every hospital, and these are backed up by a programme of regular visits, seminars and clinical teaching. The programme is proving helpful to both trainees and tutors, and has the potential to be used in the future in other developing countries.

Synthesis, crystal structure and electrical properties of the tetrahedral quaternary chalcogenides CuM{sub 2}InTe{sub 4} (M=Zn, Cd)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nolas, George S., E-mail: gnolas@usf.edu; Hassan, M. Shafiq; Dong, Yongkwan

Quaternary chalcogenides form a large class of materials that continue to be of interest for energy-related applications. Certain compositions have recently been identified as possessing good thermoelectric properties however these materials typically have the kesterite structure type with limited variation in composition. In this study we report on the structural, optical and electrical properties of the quaternary chalcogenides CuZn{sub 2}InTe{sub 4} and CuCd{sub 2}InTe{sub 4} which crystallize in the modified zinc-blende crystal structure, and compare their properties with that of CuZn{sub 2}InSe{sub 4}. These p-type semiconductors have direct band gaps of about 1 eV resulting in relatively high Seebeck coefficientmore » and resistivity values. This work expands on the research into quaternary chalcogenides with new compositions and structure types in order to further the fundamental investigation of multinary chalcogenides for potential thermoelectrics applications. - Graphical abstract: The structural, optical and electrical properties of the quaternary chalcogenides CuZn{sub 2}InTe{sub 4} and CuCd{sub 2}InTe{sub 4} are reported for the first time. The unique crystal structure allows for relatively good electrical transports and therefore potential for thermoelectric applications. - Highlights: • The physical properties of CuZn{sub 2}InTe{sub 4} and CuCd{sub 2}InTe{sub 4} are reported for the first time. • These materials have potential for thermoelectric applications. • Their direct band gaps also suggest potential for photovoltaics applications.« less

Environmental assessment of incinerator residue utilisation.

PubMed

Toller, S; Kärrman, E; Gustafsson, J P; Magnusson, Y

2009-07-01

Incineration ashes may be treated either as a waste to be dumped in landfill, or as a resource that is suitable for re-use. In order to choose the best management scenario, knowledge is needed on the potential environmental impact that may be expected, including not only local, but also regional and global impact. In this study, A life cycle assessment (LCA) based approach was outlined for environmental assessment of incinerator residue utilisation, in which leaching of trace elements as well as other emissions to air and water and the use of resources were regarded as constituting the potential environmental impact from the system studied. Case studies were performed for two selected ash types, bottom ash from municipal solid waste incineration (MSWI) and wood fly ash. The MSWI bottom ash was assumed to be suitable for road construction or as drainage material in landfill, whereas the wood fly ash was assumed to be suitable for road construction or as a nutrient resource to be recycled on forest land after biofuel harvesting. Different types of potential environmental impact predominated in the activities of the system and the use of natural resources and the trace element leaching were identified as being relatively important for the scenarios compared. The scenarios differed in use of resources and energy, whereas there is a potential for trace element leaching regardless of how the material is managed. Utilising MSWI bottom ash in road construction and recycling of wood ash on forest land saved more natural resources and energy than when these materials were managed according to the other scenarios investigated, including dumping in landfill.

Printed paper and board food contact materials as a potential source of food contamination.

PubMed

Van Bossuyt, Melissa; Van Hoeck, Els; Vanhaecke, Tamara; Rogiers, Vera; Mertens, Birgit

2016-11-01

Food contact materials (FCM) are estimated to be the largest source of food contamination. Apart from plastics, the most commonly used FCM are made of printed paper and board. Unlike their plastic counterparts, these are not covered by a specific European regulation. Several contamination issues have raised concerns towards potential adverse health effects caused by exposure to substances migrating from printed paper and board FCM. In the current study, an inventory combining the substances which may be used in printed paper and board FCM, was created. More than 6000 unique compounds were identified, the majority (77%) considered non-evaluated in terms of potential toxicity. Based on a preliminary study of their physicochemical properties, it is estimated that most of the non-evaluated single substances have the potential to migrate into the food and become bioavailable after oral intake. Almost all are included in the FACET tool, indicating that their use in primary food packaging has been confirmed by industry. Importantly, 19 substances are also present in one of the lists with substances of concern compiled by the European Chemicals Agency (ECHA). To ensure consumer safety, the actual use of these substances in printed paper and board FCM should be investigated urgently. Copyright © 2016 Elsevier Inc. All rights reserved.

An integrated study to evaluate debris flow hazard in alpine environment

NASA Astrophysics Data System (ADS)

Tiranti, Davide; Crema, Stefano; Cavalli, Marco; Deangeli, Chiara

2018-05-01

Debris flows are among the most dangerous natural processes affecting the alpine environment due to their magnitude (volume of transported material) and the long runout. The presence of structures and infrastructures on alluvial fans can lead to severe problems in terms of interactions between debris flows and human activities. Risk mitigation in these areas requires identifying the magnitude, triggers, and propagation of debris flows. Here, we propose an integrated methodology to characterize these phenomena. The methodology consists of three complementary procedures. Firstly, we adopt a classification method based on the propensity of the catchment bedrocks to produce clayey-grained material. The classification allows us to identify the most likely rheology of the process. Secondly, we calculate a sediment connectivity index to estimate the topographic control on the possible coupling between the sediment source areas and the catchment channel network. This step allows for the assessment of the debris supply, which is most likely available for the channelized processes. Finally, with the data obtained in the previous steps, we modelled the propagation and depositional pattern of debris flows with a 3D code based on Cellular Automata. The results of the numerical runs allow us to identify the depositional patterns and the areas potentially involved in the flow processes. This integrated methodology is applied to a test-bed catchment located in Northwestern Alps. The results indicate that this approach can be regarded as a useful tool to estimate debris flow related potential hazard scenarios in an alpine environment in an expeditious way without possessing an exhaustive knowledge of the investigated catchment, including data on historical debris flow events.

Toward the characterization of biological toxins using field-based FT-IR spectroscopic instrumentation

NASA Astrophysics Data System (ADS)

Schiering, David W.; Walton, Robert B.; Brown, Christopher W.; Norman, Mark L.; Brewer, Joseph; Scott, James

2004-12-01

IR spectroscopy is a broadly applicable technique for the identification of covalent materials. Recent advances in instrumentation have made Fourier Transform infrared (FT-IR) spectroscopy available for field characterization of suspect materials. Presently, this instrumentation is broadly deployed and used for the identification of potential chemical hazards. This discussion concerns work towards expanding the analytical utility of field-based FT-IR spectrometry in the characterization of biological threats. Two classes of materials were studied: biologically produced chemical toxins which were non-peptide in nature and peptide toxin. The IR spectroscopic identification of aflatoxin-B1, trichothecene T2 mycotoxin, and strychnine was evaluated using the approach of spectral searching against large libraries of materials. For pure components, the IR method discriminated the above toxins at better than the 99% confidence level. The ability to identify non-peptide toxins in mixtures was also evaluated using a "spectral stripping" search approach. For the mixtures evaluated, this method was able to identify the mixture components from ca. 32K spectral library entries. Castor bean extract containing ricin was used as a representative peptide toxin. Due to similarity in protein spectra, a SIMCA pattern recognition methodology was evaluated for classifying peptide toxins. In addition to castor bean extract the method was validated using bovine serum albumin and myoglobin as simulants. The SIMCA approach was successful in correctly classifying these samples at the 95% confidence level.

Predicting the remaining service life of concrete

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clifton, J.F.

1991-11-01

Nuclear power plants are providing, currently, about 17 percent of the U.S. electricity and many of these plants are approaching their licensed life of 40 years. The U.S. Nuclear Regulatory Commission and the Department of Energy`s Oak Ridge National Laboratory are carrying out a program to develop a methodology for assessing the remaining safe-life of the concrete components and structures in nuclear power plants. This program has the overall objective of identifying potential structural safety issues, as well as acceptance criteria, for use in evaluations of nuclear power plants for continued service. The National Institute of Standards and Technology (NIST)more » is contributing to this program by identifying and analyzing methods for predicting the remaining life of in-service concrete materials. This report examines the basis for predicting the remaining service lives of concrete materials of nuclear power facilities. Methods for predicting the service life of new and in-service concrete materials are analyzed. These methods include (1) estimates based on experience, (2) comparison of performance, (3) accelerated testing, (4) stochastic methods, and (5) mathematical modeling. New approaches for predicting the remaining service lives of concrete materials are proposed and recommendations for their further development given. Degradation processes are discussed based on considerations of their mechanisms, likelihood of occurrence, manifestations, and detection. They include corrosion, sulfate attack, alkali-aggregate reactions, frost attack, leaching, radiation, salt crystallization, and microbiological attack.« less

A simultaneous characterization and uncertainty analysis of thermal conductivity and diffusivity of bio-insulate material "Palm date Wood" obtained from a periodic method

NASA Astrophysics Data System (ADS)

Tlijani, M.; Ben Younes, R.; Durastanti, J. F.; Boudenne, A.

2010-11-01

A periodic method is used to determine simultaneously both thermal conductivity and diffusivity of various insulate materials at room temperature. The sample is placed between two metallic plates and temperature modulation is applied on the front side of one of the metallic plates. The temperature at the front and rear sides of both plates is measured and the experimental transfer function is calculated. The theoretical thermal heat transfer function is calculated by the quadripole method. Thermal conductivity and diffusivity are simultaneously identified from both real and imaginary parts of the experimental transfer function. The thermophysical parameters of several wood scale samples obtained from palm wood trees and common trees with unknown thermal properties (E) with different thicknesses were studied. The value identified for the thermal conductivity 0.03 Wm-1 K-1 compared with different insulate solid material such as glass, glass-wool and PVC is much better and close to the air conductivity, It allowed us to consider the wood scale extracted from palm wood trees, bio and renewable material as good heat insulator aiming in the future as a use for lightness applications, insulating or as a reinforcement in a given matrix. These potentialities still unknown are stengthened by the enormous quantity of such kind of wood gathered annually from palm trees and considered as wastes.

Comparison of Traditional and Innovative Techniques to Solve Technical Challenges

NASA Technical Reports Server (NTRS)

Perchonok, Michele

2010-01-01

Although NASA has an adequate food system for current missions, research is required to accommodate new requirements for future NASA exploration missions. The Inadequate Food System risk reflects the need to develop requirements and technologies that will enable NASA to provide the crew with a safe, nutritious and acceptable food system while effectively balancing appropriate resources such as mass, volume, and crew time in exploratory missions. As we go deeper into space or spend more time on the International Space Station (ISS), there will be requirements for packaged food to be stored for 3 5 years. New food packaging technologies are needed that have adequate oxygen and water barrier properties to maintain the foods' quality over this extended shelf life. NASA has been unsuccessful in identify packaging materials that meet the necessary requirements when using several traditional routes including literature reviews, workshops, and internal shelf life studies on foods packaged in various packaging materials. Small Business Innovative Research grants were used for accelerating food packaging materials research with limited success. In order to accelerate the process, a theoretical challenge was submitted to InnoCentive resulting in a partial award. A similar food packaging challenge was submitted to Yet2.com and several potential commercial packaging material suppliers were identified that, at least partially, met the requirements. Comparisons and results of these challenges will be discussed.

Blade system design studies volume II : preliminary blade designs and recommended test matrix.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Griffin, Dayton A.

2004-06-01

As part of the U.S. Department of Energy's Wind Partnerships for Advanced Component Technologies (WindPACT) program, Global Energy Concepts, LLC is performing a Blade System Design Study (BSDS) concerning innovations in materials, processes and structural configurations for application to wind turbine blades in the multi-megawatt range. The BSDS Volume I project report addresses issues and constraints identified to scaling conventional blade designs to the megawatt size range, and evaluated candidate materials, manufacturing and design innovations for overcoming and improving large blade economics. The current report (Volume II), presents additional discussion of materials and manufacturing issues for large blades, including amore » summary of current trends in commercial blade manufacturing. Specifications are then developed to guide the preliminary design of MW-scale blades. Using preliminary design calculations for a 3.0 MW blade, parametric analyses are performed to quantify the potential benefits in stiffness and decreased gravity loading by replacement of a baseline fiberglass spar with carbon-fiberglass hybrid material. Complete preliminary designs are then presented for 3.0 MW and 5.0 MW blades that incorporate fiberglass-to-carbon transitions at mid-span. Based on analysis of these designs, technical issues are identified and discussed. Finally, recommendations are made for composites testing under Part I1 of the BSDS, and the initial planned test matrix for that program is presented.« less

Localized states in advanced dielectrics from the vantage of spin- and symmetry-polarized tunnelling across MgO.

PubMed

Schleicher, F; Halisdemir, U; Lacour, D; Gallart, M; Boukari, S; Schmerber, G; Davesne, V; Panissod, P; Halley, D; Majjad, H; Henry, Y; Leconte, B; Boulard, A; Spor, D; Beyer, N; Kieber, C; Sternitzky, E; Cregut, O; Ziegler, M; Montaigne, F; Beaurepaire, E; Gilliot, P; Hehn, M; Bowen, M

2014-08-04

Research on advanced materials such as multiferroic perovskites underscores promising applications, yet studies on these materials rarely address the impact of defects on the nominally expected materials property. Here, we revisit the comparatively simple oxide MgO as the model material system for spin-polarized solid-state tunnelling studies. We present a defect-mediated tunnelling potential landscape of localized states owing to explicitly identified defect species, against which we examine the bias and temperature dependence of magnetotransport. By mixing symmetry-resolved transport channels, a localized state may alter the effective barrier height for symmetry-resolved charge carriers, such that tunnelling magnetoresistance decreases most with increasing temperature when that state is addressed electrically. Thermal excitation promotes an occupancy switchover from the ground to the excited state of a defect, which impacts these magnetotransport characteristics. We thus resolve contradictions between experiment and theory in this otherwise canonical spintronics system, and propose a new perspective on defects in dielectrics.

Haptic identification of objects and their depictions.

PubMed

Klatzky, R L; Loomis, J M; Lederman, S J; Wake, H; Fujita, N

1993-08-01

Haptic identification of real objects is superior to that of raised two-dimensional (2-D) depictions. Three explanations of real-object superiority were investigated: contribution of material information, contribution of 3-D shape and size, and greater potential for integration across the fingers. In Experiment 1, subjects, while wearing gloves that gently attenuated material information, haptically identified real objects that provided reduced cues to compliance, mass, and part motion. The gloves permitted exploration with free hand movement, a single outstretched finger, or five outstretched fingers. Performance decreased over these three conditions but was superior to identification of pictures of the same objects in all cases, indicating the contribution of 3-D structure and integration across the fingers. Picture performance was also better with five fingers than with one. In Experiment 2, the subjects wore open-fingered gloves, which provided them with material information. Consequently, the effect of type of exploration was substantially reduced but not eliminated. Material compensates somewhat for limited access to object structure but is not the primary basis for haptic object identification.

Bismuth and antimony-based oxyhalides and chalcohalides as potential optoelectronic materials

NASA Astrophysics Data System (ADS)

Ran, Zhao; Wang, Xinjiang; Li, Yuwei; Yang, Dongwen; Zhao, Xin-Gang; Biswas, Koushik; Singh, David J.; Zhang, Lijun

2018-03-01

In the last decade the ns2 cations (e.g., Pb2+ and Sn2+)-based halides have emerged as one of the most exciting new classes of optoelectronic materials, as exemplified by for instance hybrid perovskite solar absorbers. These materials not only exhibit unprecedented performance in some cases, but they also appear to break new ground with their unexpected properties, such as extreme tolerance to defects. However, because of the relatively recent emergence of this class of materials, there remain many yet to be fully explored compounds. Here, we assess a series of bismuth/antimony oxyhalides and chalcohalides using consistent first principles methods to ascertain their properties and obtain trends. Based on these calculations, we identify a subset consisting of three types of compounds that may be promising as solar absorbers, transparent conductors, and radiation detectors. Their electronic structure, connection to the crystal geometry, and impact on band-edge dispersion and carrier effective mass are discussed.

Global optimisation methods for poroelastic material characterisation using a clamped sample in a Kundt tube setup

NASA Astrophysics Data System (ADS)

Vanhuyse, Johan; Deckers, Elke; Jonckheere, Stijn; Pluymers, Bert; Desmet, Wim

2016-02-01

The Biot theory is commonly used for the simulation of the vibro-acoustic behaviour of poroelastic materials. However, it relies on a number of material parameters. These can be hard to characterize and require dedicated measurement setups, yielding a time-consuming and costly characterisation. This paper presents a characterisation method which is able to identify all material parameters using only an impedance tube. The method relies on the assumption that the sample is clamped within the tube, that the shear wave is excited and that the acoustic field is no longer one-dimensional. This paper numerically shows the potential of the developed method. It therefore performs a sensitivity analysis of the quantification parameters, i.e. reflection coefficients and relative pressures, and a parameter estimation using global optimisation methods. A 3-step procedure is developed and validated. It is shown that even in the presence of numerically simulated noise this procedure leads to a robust parameter estimation.

High-Throughput Characterization of Porous Materials Using Graphics Processing Units

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Jihan; Martin, Richard L.; Rübel, Oliver

We have developed a high-throughput graphics processing units (GPU) code that can characterize a large database of crystalline porous materials. In our algorithm, the GPU is utilized to accelerate energy grid calculations where the grid values represent interactions (i.e., Lennard-Jones + Coulomb potentials) between gas molecules (i.e., CHmore » $$_{4}$$ and CO$$_{2}$$) and material's framework atoms. Using a parallel flood fill CPU algorithm, inaccessible regions inside the framework structures are identified and blocked based on their energy profiles. Finally, we compute the Henry coefficients and heats of adsorption through statistical Widom insertion Monte Carlo moves in the domain restricted to the accessible space. The code offers significant speedup over a single core CPU code and allows us to characterize a set of porous materials at least an order of magnitude larger than ones considered in earlier studies. For structures selected from such a prescreening algorithm, full adsorption isotherms can be calculated by conducting multiple grand canonical Monte Carlo simulations concurrently within the GPU.« less

Bismuth and antimony-based oxyhalides and chalcohalides as potential optoelectronic materials

DOE PAGES

Ran, Zhao; Wang, Xinjiang; Li, Yuwei; ...

2018-03-22

In the last decade the ns 2 cations (e.g., Pb 2+ and Sn 2+)-based halides have emerged as one of the most exciting new classes of optoelectronic materials, as exemplified by for instance hybrid perovskite solar absorbers. These materials not only exhibit unprecedented performance in some cases, but they also appear to break new ground with their unexpected properties, such as extreme tolerance to defects. However, because of the relatively recent emergence of this class of materials, there remain many yet to be fully explored compounds. Here, we assess a series of bismuth/antimony oxyhalides and chalcohalides using consistent first principlesmore » methods to ascertain their properties and obtain trends. Based on these calculations, we identify a subset consisting of three types of compounds that may be promising as solar absorbers, transparent conductors, and radiation detectors. Their electronic structure, connection to the crystal geometry, and impact on band-edge dispersion and carrier effective mass are discussed.« less

Lunar oxygen and metal for use in near-Earth space: Magma electrolysis

NASA Technical Reports Server (NTRS)

Colson, Russell O.; Haskin, Larry A.

1990-01-01

Because it is energetically easier to get material from the Moon to Earth orbit than from the Earth itself, the Moon is a potentially valuable source of materials for use in space. The unique conditions on the Moon, such as vacuum, absence of many reagents common on the Earth, and the presence of very nontraditional ores suggest that a unique and nontraditional process for extracting materials from the ores may prove the most practical. With this in mind, an investigation of unfluxed silicate electrolysis as a method for extracting oxygen, iron, and silicon from lunar regolith was initiated and is discussed. The advantages of the process include simplicity of concept, absence of need to supply reagents from Earth, and low power and mass requirements for the processing plant. Disadvantages include the need for uninterrupted high temperature and the highly corrosive nature of the high-temperature silicate melts which has made identifying suitable electrode and container materials difficult.

Application of Surface Analysis Methods to Nanomaterials: Summaryof ISO/TC 201 Technical Report: ISO 14187:2011 -Surface Chemical Analysis- Characterization of Nanomaterials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baer, Donald R.

ISO Technical Report (TR) 14187 provides an introduction to (and examples of) the information that can be obtained about nanostructured materials using surface-analysis tools. In addition, both general issues and challenges associated with characterising nanostructured materials and the specific opportunities and challenges associated with individual analytical methods are identified. As the size of objects or components of materials approaches a few nanometres, the distinctions among 'bulk', 'surface' and 'particle' analysis blur. This Technical Report focuses on issues specifically relevant to surface chemical analysis of nanostructured materials. The report considers a variety of analysis methods but focuses on techniques that aremore » in the domain of ISO/TC 201 including Auger electron spectroscopy, X-ray photoelectron spectroscopy, secondary ion mass spectrometry, and scanning probe microscopy. Measurements of nanoparticle surface properties such as surface potential that are often made in a solution are not discussed.« less

Lime as an Anti-Plasticizer for Self-Compacting Clay Concrete

PubMed Central

Landrou, Gnanli; Brumaud, Coralie; Winnefeld, Frank; Flatt, Robert J.; Habert, Guillaume

2016-01-01

This paper focuses on the modification of clay properties with inorganic additives to deflocculate and flocculate inorganic soil for the development of a material that would be as easy to use as the current concrete products, but with a much lower environmental impact. Considering that the rheological behaviour of clays is controlled by their surface charge, we first introduce potential determining ions to deflocculate the clay particles and to reduce the yield stress of the earth material. Their efficiency is characterized using zeta potential measurements and rheological tests. We then achieve the flocculation of clay particles by using natural minerals that slowly dissolve in the interstitial liquid and ultimately precipitate calcium silicate hydrate (C–S–H). The precipitation products are identified by X-ray diffraction and the consequences of this delayed precipitation are followed by oscillatory rheometric measurements. Finally, it is suggested that in this process, C–S–H precipitation is not used as a binding vector but as an anti-plasticizer that removes the inorganic dispersant additives. PMID:28773453

Lime as an Anti-Plasticizer for Self-Compacting Clay Concrete.

PubMed

Landrou, Gnanli; Brumaud, Coralie; Winnefeld, Frank; Flatt, Robert J; Habert, Guillaume

2016-04-29

This paper focuses on the modification of clay properties with inorganic additives to deflocculate and flocculate inorganic soil for the development of a material that would be as easy to use as the current concrete products, but with a much lower environmental impact. Considering that the rheological behaviour of clays is controlled by their surface charge, we first introduce potential determining ions to deflocculate the clay particles and to reduce the yield stress of the earth material. Their efficiency is characterized using zeta potential measurements and rheological tests. We then achieve the flocculation of clay particles by using natural minerals that slowly dissolve in the interstitial liquid and ultimately precipitate calcium silicate hydrate (C-S-H). The precipitation products are identified by X-ray diffraction and the consequences of this delayed precipitation are followed by oscillatory rheometric measurements. Finally, it is suggested that in this process, C-S-H precipitation is not used as a binding vector but as an anti-plasticizer that removes the inorganic dispersant additives.

Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stoessel, Chris

2013-11-13

This project developed a new high-performance R-10/high SHGC window design, reviewed market positioning and evaluated manufacturing solutions required for broad market adoption. The project objectives were accomplished by: identifying viable technical solutions based on modeling of modern and potential coating stacks and IGU designs; development of new coating material sets for HM thin film stacks, as well as improved HM IGU designs to accept multiple layers of HM films; matching promising new coating designs with new HM IGU designs to demonstrate performance gains; and, in cooperation with a window manufacturer, assess the potential for high-volume manufacturing and cost efficiency ofmore » a HM-based R-10 window with improved solar heat gain characteristics. A broad view of available materials and design options was applied to achieve the desired improvements. Gated engineering methodologies were employed to guide the development process from concept generation to a window demonstration. The project determined that a slightly de-rated window performance allows formulation of a path to achieve the desired cost reductions to support end consumer adoption.« less

U.S. Geological Survey Field Leach Test for Assessing Water Reactivity and Leaching Potential of Mine Wastes, Soils, and Other Geologic and Environmental Materials

USGS Publications Warehouse

Hageman, Philip L.

2007-01-01

The U. S. Geological Survey (USGS) has developed a fast (5-minute), effective, simple, and cost-effective leach test that can be used to simulate the reactions that occur when materials are leached by water. The USGS Field Leach Test has been used to predict, assess, and characterize the geochemical interactions between water and a broad variety of geologic and environmental matrices. Examples of some of the samples leached include metal mine wastes, various types of dusts, biosolids (processed sewage sludge), flood and wetland sediments, volcanic ash, forest-fire burned soils, and many other diverse matrices. The Field Leach Test has been an integral part of these investigations and has demonstrated its value as a geochemical characterization tool. It has enabled investigators to identify which constituents are water reactive, soluble, mobilized, and made bioaccessible because of leaching by water, and to understand potential impacts of these interactions on the surrounding environment.

A co-crystal between benzene and ethane: a potential evaporite material for Saturn’s moon Titan

PubMed Central

Maynard-Casely, Helen E.; Hodyss, Robert; Cable, Morgan L.; Vu, Tuan Hoang; Rahm, Martin

2016-01-01

Using synchrotron X-ray powder diffraction, the structure of a co-crystal between benzene and ethane formed in situ at cryogenic conditions has been determined, and validated using dispersion-corrected density functional theory calculations. The structure comprises a lattice of benzene molecules hosting ethane molecules within channels. Similarity between the intermolecular interactions found in the co-crystal and in pure benzene indicate that the C—H⋯π network of benzene is maintained in the co-crystal, however, this expands to accommodate the guest ethane molecules. The co-crystal has a 3:1 benzene:ethane stoichiometry and is described in the space group with a = 15.977 (1) Å and c = 5.581 (1) Å at 90 K, with a density of 1.067 g cm−3. The conditions under which this co-crystal forms identify it is a potential that forms from evaporation of Saturn’s moon Titan’s lakes, an evaporite material. PMID:27158505

Readability and Content of Patient Education Material Related to Implantable Cardioverter Defibrillators

PubMed Central

Strachan, Patricia H.; de Laat, Sonya; Carroll, Sandra L.; Schwartz, Lisa; Vaandering, Katie; Toor, Gurjit K.; Arthur, Heather M.

2012-01-01

Background Implantable cardioverter defibrillators (ICDs) are increasingly offered to patients for primary prevention of sudden cardiac death. Candidates for ICD receive ICD-related patient education material when they make decisions to consent or decline a primary prevention ICD. Printed patient education material directed at ICD candidates has not been the focus of direct appraisal. Objective We evaluated the readability and content of ICD-related print education materials made available to patients who were enrolled in a study involving patient decision making for ICD from 3 ICD sites in southern Ontario, Canada. Methods All ICD print materials referred to during interviews and/or that were available in ICD site waiting rooms were collected for analysis. Readability testing was conducted using the SMOG (“simple measurement of gobbledygook”) and Fry methods. The material was evaluated according to selected plain-language criteria, thematic content analysis, and rhetoric analysis. Results Twenty-one print materials were identified and analyzed. Documents were authored by device manufacturers, tertiary care hospitals, and cardiac support organizations. Although many documents adhered to plain-language recommendations, text-reading levels were higher than recommended. Twelve major content themes were identified. Content focused heavily on the positive aspects of living with the device to the exclusion of other possible information that could be relevant to the decisions that patients made. Conclusions Print-based patient education materials for ICD candidates are geared to a highly literate population. The focus on positive information to the exclusion of potentially negative aspects of the ICD, or alternatives to accepting 1, could influence and/or confuse patients about the purpose and implications of this medical device. Development of print materials is indicated that includes information about possible problems and that would be relevant for the multicultural and debilitated population who may require ICDs. The findings are highly relevant for nurses who care for primary prevention ICD candidates. PMID:21926915