Science.gov

Sample records for ifmif accelerator structural

  1. The IFMIF-EVEDA accelerator beam dump design

    NASA Astrophysics Data System (ADS)

    Iglesias, D.; Arranz, F.; Arroyo, J. M.; Barrera, G.; Brañas, B.; Casal, N.; García, M.; López, D.; Martínez, J. I.; Mayoral, A.; Ogando, F.; Parro, M.; Oliver, C.; Rapisarda, D.; Sanz, J.; Sauvan, P.; Ibarra, A.

    2011-10-01

    The IFMIF-EVEDA accelerator will be a 9 MeV, 125 mA cw deuteron accelerator prototype for verifying the validity of the 40 MeV accelerator design for IFMIF. A beam dump designed for maximum power of 1.12 MW will be used to stop the beam at the accelerator exit. The conceptual design for the IFMIF-EVEDA accelerator beam dump is based on a conical beam stop made of OFE copper. The cooling system uses an axial high velocity flow of water pressurized up to 3.4 × 10 5 Pa to avoid boiling. The design has been shown to be compliant with ASME mechanical design rules under nominal full power conditions. A sensitivity analysis has been performed to take into account the possible margin on the beam properties at the beam dump entrance. This analysis together with the study of the maintenance issues and the mounting and dismounting operations has led to the complete design definition.

  2. Thermo-structural analysis and design consideration of the replaceable backwall in IFMIF liquid lithium target

    NASA Astrophysics Data System (ADS)

    Nakamura, H.; Ida, M.; Chida, T.; Shiba, K.; Shimizu, K.; Sugimoto, M.

    2007-08-01

    The IFMIF is an accelerator-based intense neutron source for testing candidate materials for fusion reactors. Intense neutrons are emitted inside the Li flow through a backwall. The backwall made of 316L stainless steel or RAFM is attached to the target assembly with a lip seal welded by a YAG laser. Since the backwall is operating under a severe neutron irradiation of 50 dpa/year and a maximum nuclear heating rate of 25 W/cm 3, thermo-structural design is one of critical issues in a target design. Thermal stress was calculated using the ABAQUS code. As a permissible stress, yield strength at 300 °C was used. In the case of the 316 stainless steel backwall, the maximum thermal stress was more than the permissible stress (164 MPa). On the other hand, in case of the F82H backwall, a maximum thermal stress was below the permissible stress (455 MPa). Therefore, F82H is recommended as the backwall material.

  3. Thermo-structural analysis of target assembly and back plate in the IFMIF/EVEDA lithium test loop

    NASA Astrophysics Data System (ADS)

    Watanabe, Kazuyoshi; Ida, Mizuho; Kondo, Hiroo; Miyashita, Makoto; Nakamura, Hiroo

    2011-10-01

    IFMIF is an accelerator-based intense neutron source for testing candidate materials for fusion reactors. The Engineering Validation and Engineering Design Activities (EVEDA) of IFMIF are in progress under the Broader Approach Agreement. In the EVEDA Li test loop, two types of target assemblies, "an integrated type target assembly without a back plate", made of SUS316L, and "a target assembly with replaceable bayonet back plate", made of F82H steel, will be evaluated. For these target assemblies, thermal stresses were evaluated using the ABAQUS code. As the permitted stress, the values of yield strengths at 300 °C were used. In the case of the integrated target assembly, the maximum thermal stress was below the allowed stress (164 MPa). However, in the case of the target assembly with the bayonet back plate, thermal insulation around the back plate should be necessary to reduce the thermal stress below the allowed value (455 MPa).

  4. RFQ Designs and Beam-Loss Distributions for IFMIF

    SciTech Connect

    Jameson, Robert A

    2007-01-01

    The IFMIF 125 mA cw 40 MeV accelerators will set an intensity record. Minimization of particle loss along the accelerator is a top-level requirement and requires sophisticated design intimately relating the accelerated beam and the accelerator structure. Such design technique, based on the space-charge physics of linear accelerators (linacs), is used in this report in the development of conceptual designs for the Radio-Frequency-Quadrupole (RFQ) section of the IFMIF accelerators. Design comparisons are given for the IFMIF CDR Equipartitioned RFQ, a CDR Alternative RFQ, and new IFMIF Post-CDR Equipartitioned RFQ designs. Design strategies are illustrated for combining several desirable characteristics, prioritized as minimum beam loss at energies above ~ 1 MeV, low rf power, low peak field, short length, high percentage of accelerated particles. The CDR design has ~0.073% losses above 1 MeV, requires ~1.1 MW rf structure power, has KP factor 1.7,is 12.3 m long, and accelerates ~89.6% of the input beam. A new Post-CDR design has ~0.077% losses above 1 MeV, requires ~1.1 MW rf structure power, has KP factor 1.7 and ~8 m length, and accelerates ~97% of the input beam. A complete background for the designs is given, and comparisons are made. Beam-loss distributions are used as input for nuclear physics simulations of radioactivity effects in the IFMIF accelerator hall, to give information for shielding, radiation safety and maintenance design. Beam-loss distributions resulting from a ~1M particle input distribution representative of the IFMIF ECR ion source are presented. The simulations reported were performed with a consistent family of codes. Relevant comparison with other codes has not been possible as their source code is not available. Certain differences have been noted but are not consistent over a broad range of designs and parameter range. The exact transmission found by any of these codes should be treated as indicative, as each has various sensitivities in

  5. Program system for three-dimensional coupled Monte Carlo-deterministic shielding analysis with application to the accelerator-based IFMIF neutron source

    NASA Astrophysics Data System (ADS)

    Chen, Y.; Fischer, U.

    2005-10-01

    A program system for three-dimensional coupled Monte Carlo-deterministic shielding analysis has been developed to solve problems with complex geometry and bulk shield by integrating the Monte Carlo transport code MCNP, the three-dimensional discrete ordinates code TORT and a coupling interface program. A newly-proposed mapping approach is implemented in the interface program to calculate the angular flux distribution from the scored Monte Carlo particle tracks and generate the boundary source file for the use of TORT. Test calculations were performed with comparison to MCNP solutions. Satisfactory agreements were obtained between the results calculated by these two approaches. The program system has been chosen to treat the complicated shielding problem of the accelerator-based IFMIF neutron source. The successful application demonstrates that coupling scheme with the program system is a useful computational tool for the shielding analysis of complex and large nuclear facilities.

  6. Overview of the IFMIF/EVEDA project

    NASA Astrophysics Data System (ADS)

    Knaster, J.; Garin, P.; Matsumoto, H.; Okumura, Y.; Sugimoto, M.; Arbeiter, F.; Cara, P.; Chel, S.; Facco, A.; Favuzza, P.; Furukawa, T.; Heidinger, R.; Ibarra, A.; Kanemura, T.; Kasugai, A.; Kondo, H.; Massaut, V.; Molla, J.; Micciche, G.; O'hira, S.; Sakamoto, K.; Yokomine, T.; Wakai, E.; the IFMIF/EVEDA Integrated Project Team

    2017-10-01

    IFMIF, the International Fusion Materials Irradiation Facility, is presently in its engineering validation and engineering design activities (EVEDA) phase under the Broader Approach Agreement. The engineering design activity (EDA) phase was successfully accomplished within the allocated time. The engineering validation activity (EVA) phase has focused on validating the Accelerator Facility (AF), the Target Facility and the Test Facility (TF) by constructing prototypes. The ELTL at JAEAc, Oarai successfully demonstrated the long-term stability of a Li flow under the IFMIF’s nominal operational conditions keeping the specified free-surface fluctuations below  ±1 mm in a continuous manner for 25 d. A full-scale prototype of the high flux test module (HFTM) was successfully tested in the HELOKA loop (KIT, Karlsruhe), where it was demonstrated that the irradiation temperature can be set individually and kept uniform. LIPAc, designed and constructed in European labs under the coordination of F4E, presently under installation and commissioning in the Rokkasho Fusion Institute, aims at validating the concept of IFMIF accelerators with a D+ beam of 125 mA continuous wave (CW) and 9 MeV. The commissioning phases of the H+/D+ beams at 100 keV are progressing and should be concluded in 2017; in turn, the commissioning of the 5 MeV beam is due to start during 2017. The D+ beam through the superconducting cavities is expected to be achieved within the Broader Approach Agreement time frame with the superconducting cryomodule being assembled in Rokkasho. The realisation of a fusion-relevant neutron source is a necessary step for the successful development of fusion. The ongoing success of the IFMIF/EVEDA involves ruling out concerns about potential technical showstoppers which were raised in the past. Thus, a situation has emerged where soon steps towards constructing a Li(d,xn) fusion-relevant neutron source could be taken, which is also justified in the light of costs

  7. The foxhole accelerating structure

    SciTech Connect

    Fernow, R.C.; Claus, J.

    1992-07-17

    This report examines some properties of a new type of open accelerating structure. It consists of a series of rectangular cavities, which we call foxholes, joined by a beam channel. The power for accelerating the particles comes from an external radiation source and enters the cavities through their open upper surfaces. Analytic and computer calculations are presented showing that the foxhole is a suitable structure for accelerating relativistic electrons.

  8. Fiber Accelerating Structures

    SciTech Connect

    Hammond, Andrew P.; /Reed Coll. /SLAC

    2010-08-25

    One of the options for future particle accelerators are photonic band gap (PBG) fiber accelerators. PBG fibers are specially designed optical fibers that use lasers to excite an electric field that is used to accelerate electrons. To improve PBG accelerators, the basic parameters of the fiber were tested to maximize defect size and acceleration. Using the program CUDOS, several accelerating modes were found that maximized these parameters for several wavelengths. The design of multiple defects, similar to having closely bound fibers, was studied to find possible coupling or the change of modes. The amount of coupling was found to be dependent on distance separated. For certain distances accelerating coupled modes were found and examined. In addition, several non-periodic fiber structures were examined using CUDOS. The non-periodic fibers produced several interesting results and promised more modes given time to study them in more detail.

  9. TESLA superconducting accelerating structures

    NASA Astrophysics Data System (ADS)

    Sekutowicz, J.

    2007-08-01

    Superconducting standing wave structures have been used for charged particle acceleration for almost 40 years. A brief introduction to this application with examples, test procedures and recently achieved results are discussed in this paper.

  10. Dielectric assist accelerating structure

    NASA Astrophysics Data System (ADS)

    Satoh, D.; Yoshida, M.; Hayashizaki, N.

    2016-01-01

    A higher-order TM02 n mode accelerating structure is proposed based on a novel concept of dielectric loaded rf cavities. This accelerating structure consists of ultralow-loss dielectric cylinders and disks with irises which are periodically arranged in a metallic enclosure. Unlike conventional dielectric loaded accelerating structures, most of the rf power is stored in the vacuum space near the beam axis, leading to a significant reduction of the wall loss, much lower than that of conventional normal-conducting linac structures. This allows us to realize an extremely high quality factor and a very high shunt impedance at room temperature. A simulation of a 5 cell prototype design with an existing alumina ceramic indicates an unloaded quality factor of the accelerating mode over 120 000 and a shunt impedance exceeding 650 M Ω /m at room temperature.

  11. Transmutation analysis of realistic low-activation steels for magnetic fusion reactors and IFMIF

    SciTech Connect

    Cabellos, O; Sanz, J; Garc?a-Herranz, N; D?az, S; Reyes, S; Piedloup, S

    2005-11-22

    A comprehensive transmutation study for steels considered in the selection of structural materials for magnetic and inertial fusion reactors has been performed in the IFMIF neutron irradiation scenario, as well as in the ITER and DEMO ones for comparison purposes. An element-by-element transmutation approach is used in the study, addressing the generation of: (1) H and He and (2) solid transmutants. The IEAF-2001 activation library and the activation code ACAB were applied to the IFMIF transmutation analysis, after proving the applicability of ACAB for transmutation calculations of this kind of intermediate energy systems.

  12. 1996 Design effort for IFMIF HEBT

    SciTech Connect

    Blind, B.

    1997-01-01

    The paper details the 1996 design effort for the IFMIF HEBT. Following a brief overview, it lists the primary requirements for the beam at the target, describes the design approach and design tools used, introduces the beamline modules, gives the results achieved with the design at this stage, points out possible improvements and gives the names and computer locations of the TRACE3-D and PARMILA files that sum up the design work. The design does not fully meet specifications in regards to the flatness of the distribution at the target. With further work, including if necessary some backup options, the flatness specifications may be realized. It is not proposed that the specifications, namely flatness to {+-}5% and higher-intensity ridges that are no more than 15% above average, be changed at this time. The design also does not meet the requirement that the modules of all beamlines should operate at the same settings. However, the goal of using identical components and operational procedures has been met and only minor returning is needed to produce very similar beam distributions from all beamlines. Significant further work is required in the following areas: TRACE3-D designs and PARMILA runs must be made for the beams coming from accelerators No. 3 and No. 4. Transport of 30-MeV and 35-MeV beams to the targets and beam dump must be studied. Comprehensive error studies must be made. These must result in tolerance specifications and may require design iterations. Detailed interfacing with target-spot instrumentation is required. This instrumentation must be able to check all aspects of the specifications.

  13. Plasma-based accelerator structures

    SciTech Connect

    Schroeder, Carl B.

    1999-12-01

    Plasma-based accelerators have the ability to sustain extremely large accelerating gradients, with possible high-energy physics applications. This dissertation further develops the theory of plasma-based accelerators by addressing three topics: the performance of a hollow plasma channel as an accelerating structure, the generation of ultrashort electron bunches, and the propagation of laser pulses is underdense plasmas.

  14. Accelerator structure work for NLC

    SciTech Connect

    Miller, R.H.; Adolphsen, C.; Bane, K.L.F.; Deruyter, H.; Farkas, Z.D.; Hoag, H.A.; Holtkamp, N.; Lavine, T.; Loew, G.A.; Nelson, E.M.; Palmer, R.B.; Paterson, J.M.; Ruth, R.D.; Thompson, K.A.; Vlieks, A.; Wang, J.W.; Wilson, P.B. ); Gluckstern, R. ); Ko, K.; Kroll, N. (Stanford Linear Accelerator Ce

    1992-07-01

    The NLC design achieves high luminosity with multiple bunches in each RF pulse. Acceleration of a train of bunches without emittance growth requires control of long range dipole wakefields. SLAC is pursuing a structure design which suppresses the effect of wakefields by varying the physical dimensions of successive cells of the disk-loaded traveling wave structure in a manner which spreads the frequencies of the higher mode while retaining the synchronism between the electrons and the accelerating mode. The wakefields of structures incorporating higher mode detuning have been measured at the Accelerator Test Facility at Argonne. Mechanical design and brazing techniques which avoid getting brazing alloy into the interior of the accelerator are being studied. A test facility for high-power testing of these structures is complete and high power testing has begun.

  15. Accelerator structure work for NLC

    SciTech Connect

    Miller, R.H.; Adolphsen, C.; Bane, K.L.F.; Deruyter, H.; Farkas, Z.D.; Hoag, H.A.; Holtkamp, N.; Lavine, T.; Loew, G.A.; Nelson, E.M.; Palmer, R.B.; Paterson, J.M.; Ruth, R.D.; Thompson, K.A.; Vlieks, A.; Wang, J.W.; Wilson, P.B.; Gluckstern, R.; Ko, K.; Kroll, N. |

    1992-07-01

    The NLC design achieves high luminosity with multiple bunches in each RF pulse. Acceleration of a train of bunches without emittance growth requires control of long range dipole wakefields. SLAC is pursuing a structure design which suppresses the effect of wakefields by varying the physical dimensions of successive cells of the disk-loaded traveling wave structure in a manner which spreads the frequencies of the higher mode while retaining the synchronism between the electrons and the accelerating mode. The wakefields of structures incorporating higher mode detuning have been measured at the Accelerator Test Facility at Argonne. Mechanical design and brazing techniques which avoid getting brazing alloy into the interior of the accelerator are being studied. A test facility for high-power testing of these structures is complete and high power testing has begun.

  16. A 140 mA cw deuteron electron cyclotron resonance source for the IFMIF-EVEDA project.

    PubMed

    Gobin, R; Beauvais, P-Y; Delferrière, O; De Menezes, D; Tuske, O; Adroit, G; Gauthier, Y; Harrault, F

    2008-02-01

    In the framework of the IFMIF-EVEDA phase (International Fusion Materials Irradiation Facility-Engineering Validation and Engineering Design Activities), the CEA-Saclay is in charged of the design and realization of the 140 mA cw deuteron source. The IFMIF EVEDA demonstrator will be installed in Japan in the next six years and will have to accelerate the deuteron beam up to 9 MeV. CEA will build the source and the low energy beam line (LEBT) and will test the cw high intensity deuteron production at Saclay. The SILHI source is an electron cyclotron resonance (ECR) source, operating at 2.45 GHz. In 2001, it produced more than 130 mA of deuteron beam in pulsed mode to minimize neutron production. Such a result pushes to develop a new ECR source based on the SILHI design and equipped with a specific extraction system. Several options of the accelerator column will be implemented in order to improve the reliability and the efficiency of the source. The IFMIF source and LEBT design will be reported.

  17. Accelerator structure development for NLC

    SciTech Connect

    Hoag, H.A.; Deruyter, H.; Pearson, C.; Ruth, R.D.; Wang, J.W.; Schaefer, J.

    1993-04-01

    In the program of work directed towards the development of an X-Band Next Linear Collider accelerator structure, two different test accelerator sections have been completed, and a third is being fabricated. The first is a simple 30-cell constant-impedance section in which no special attention was given to surface finish, pumping, and alignment. The second is an 86-cell section in which the cells were precision diamond-turned by Texas Instruments Inc. The structure has internal water-cooling and vacuum pumping manifolds. Some design details are given for the third section, which is a 206-cell structure with cavities dimensioned to give a Gaussian distribution of dipole mode frequencies. It has conventional-machining surface finishes and external water and pumping manifolds. Component design, fabrication, and assembly brazing are described for the first two experimental sections.

  18. Photonic Crystal Laser Accelerator Structures

    SciTech Connect

    Cowan, Benjamin M

    2003-05-21

    Photonic crystals have great potential for use as laser-driven accelerator structures. A photonic crystal is a dielectric structure arranged in a periodic geometry. Like a crystalline solid with its electronic band structure, the modes of a photonic crystal lie in a set of allowed photonic bands. Similarly, it is possible for a photonic crystal to exhibit one or more photonic band gaps, with frequencies in the gap unable to propagate in the crystal. Thus photonic crystals can confine an optical mode in an all-dielectric structure, eliminating the need for metals and their characteristic losses at optical frequencies. We discuss several geometries of photonic crystal accelerator structures. Photonic crystal fibers (PCFs) are optical fibers which can confine a speed-of-light optical mode in vacuum. Planar structures, both two- and three-dimensional, can also confine such a mode, and have the additional advantage that they can be manufactured using common microfabrication techniques such as those used for integrated circuits. This allows for a variety of possible materials, so that dielectrics with desirable optical and radiation-hardness properties can be chosen. We discuss examples of simulated photonic crystal structures to demonstrate the scaling laws and trade-offs involved, and touch on potential fabrication processes.

  19. Operation and commissioning of IFMIF (International Fusion Materials Irradiation Facility) LIPAc injector.

    PubMed

    Okumura, Y; Gobin, R; Knaster, J; Heidinger, R; Ayala, J-M; Bolzon, B; Cara, P; Chauvin, N; Chel, S; Gex, D; Harrault, F; Ichimiya, R; Ihara, A; Ikeda, Y; Kasugai, A; Kikuchi, T; Kitano, T; Komata, M; Kondo, K; Maebara, S; Marqueta, A; O'Hira, S; Perez, M; Phillips, G; Pruneri, G; Sakamoto, K; Scantamburlo, F; Senée, F; Shinto, K; Sugimoto, M; Takahashi, H; Usami, H; Valette, M

    2016-02-01

    The objective of linear IFMIF prototype accelerator is to demonstrate 125 mA/CW deuterium ion beam acceleration up to 9 MeV. The injector has been developed in CEA Saclay and already demonstrated 140 mA/100 keV deuterium beam [R. Gobin et al., Rev. Sci. Instrum. 85, 02A918 (2014)]. The injector was disassembled and delivered to the International Fusion Energy Research Center in Rokkasho, Japan. After reassembling the injector, commissioning has started in 2014. Up to now, 100 keV/120 mA/CW hydrogen and 100 keV/90 mA/CW deuterium ion beams have been produced stably from a 10 mm diameter extraction aperture with a low beam emittance of 0.21 π mm mrad (rms, normalized). Neutron production by D-D reaction up to 2.4 × 10(9) n/s has been observed in the deuterium operation.

  20. Operation and commissioning of IFMIF (International Fusion Materials Irradiation Facility) LIPAc injector

    SciTech Connect

    Okumura, Y. E-mail: rjgobin@cea.fr; Knaster, J.; Ayala, J.-M.; Marqueta, A.; Perez, M.; Pruneri, G.; Scantamburlo, F.; Ichimiya, R.; Ihara, A.; and others

    2016-02-15

    The objective of linear IFMIF prototype accelerator is to demonstrate 125 mA/CW deuterium ion beam acceleration up to 9 MeV. The injector has been developed in CEA Saclay and already demonstrated 140 mA/100 keV deuterium beam [R. Gobin et al., Rev. Sci. Instrum. 85, 02A918 (2014)]. The injector was disassembled and delivered to the International Fusion Energy Research Center in Rokkasho, Japan. After reassembling the injector, commissioning has started in 2014. Up to now, 100 keV/120 mA/CW hydrogen and 100 keV/90 mA/CW deuterium ion beams have been produced stably from a 10 mm diameter extraction aperture with a low beam emittance of 0.21 π mm mrad (rms, normalized). Neutron production by D-D reaction up to 2.4 × 10{sup 9} n/s has been observed in the deuterium operation.

  1. The accomplishment of the Engineering Design Activities of IFMIF/EVEDA: The European-Japanese project towards a Li(d,xn) fusion relevant neutron source

    NASA Astrophysics Data System (ADS)

    Knaster, J.; Ibarra, A.; Abal, J.; Abou-Sena, A.; Arbeiter, F.; Arranz, F.; Arroyo, J. M.; Bargallo, E.; Beauvais, P.-Y.; Bernardi, D.; Casal, N.; Carmona, J. M.; Chauvin, N.; Comunian, M.; Delferriere, O.; Delgado, A.; Diaz-Arocas, P.; Fischer, U.; Frisoni, M.; Garcia, A.; Garin, P.; Gobin, R.; Gouat, P.; Groeschel, F.; Heidinger, R.; Ida, M.; Kondo, K.; Kikuchi, T.; Kubo, T.; Le Tonqueze, Y.; Leysen, W.; Mas, A.; Massaut, V.; Matsumoto, H.; Micciche, G.; Mittwollen, M.; Mora, J. C.; Mota, F.; Nghiem, P. A. P.; Nitti, F.; Nishiyama, K.; Ogando, F.; O'hira, S.; Oliver, C.; Orsini, F.; Perez, D.; Perez, M.; Pinna, T.; Pisent, A.; Podadera, I.; Porfiri, M.; Pruneri, G.; Queral, V.; Rapisarda, D.; Roman, R.; Shingala, M.; Soldaini, M.; Sugimoto, M.; Theile, J.; Tian, K.; Umeno, H.; Uriot, D.; Wakai, E.; Watanabe, K.; Weber, M.; Yamamoto, M.; Yokomine, T.

    2015-08-01

    The International Fusion Materials Irradiation Facility (IFMIF), presently in its Engineering Validation and Engineering Design Activities (EVEDA) phase under the frame of the Broader Approach Agreement between Europe and Japan, accomplished in summer 2013, on schedule, its EDA phase with the release of the engineering design report of the IFMIF plant, which is here described. Many improvements of the design from former phases are implemented, particularly a reduction of beam losses and operational costs thanks to the superconducting accelerator concept, the re-location of the quench tank outside the test cell (TC) with a reduction of tritium inventory and a simplification on its replacement in case of failure, the separation of the irradiation modules from the shielding block gaining irradiation flexibility and enhancement of the remote handling equipment reliability and cost reduction, and the water cooling of the liner and biological shielding of the TC, enhancing the efficiency and economy of the related sub-systems. In addition, the maintenance strategy has been modified to allow a shorter yearly stop of the irradiation operations and a more careful management of the irradiated samples. The design of the IFMIF plant is intimately linked with the EVA phase carried out since the entry into force of IFMIF/EVEDA in June 2007. These last activities and their on-going accomplishment have been thoroughly described elsewhere (Knaster J et al [19]), which, combined with the present paper, allows a clear understanding of the maturity of the European-Japanese international efforts. This released IFMIF Intermediate Engineering Design Report (IIEDR), which could be complemented if required concurrently with the outcome of the on-going EVA, will allow decision making on its construction and/or serve as the basis for the definition of the next step, aligned with the evolving needs of our fusion community.

  2. CVD Diamond Dielectric Accelerating Structures

    SciTech Connect

    Schoessow, P.; Kanareykin, A.; Gat, R.

    2009-01-22

    The electrical and mechanical properties of diamond make it an ideal candidate material for use in dielectric accelerating structures: high RF breakdown field, extremely low dielectric losses and the highest available thermoconductive coefficient. Using chemical vapor deposition (CVD) cylindrical diamond structures have been manufactured with dimensions corresponding to fundamental TM{sub 01} mode frequencies in the GHz to THz range. Surface treatments are being developed to reduce the secondary electron emission (SEE) coefficient below unity to reduce the possibility of multipactor. The diamond CVD cylindrical waveguide technology developed here can be applied to a variety of other high frequency, large-signal applications.

  3. Vibrational Stability of NLC Linac accelerating structure

    SciTech Connect

    Le Pimpec, Frederic

    2002-09-25

    The vibration of components of the NLC linac, such as accelerating structures and girders, is being studied both experimentally and analytically. Various effects are being considered including structural resonances and vibration caused by cooling water in the accelerating structure. This paper reports the status of ongoing work.

  4. Photonic Crystal Laser-Driven Accelerator Structures

    SciTech Connect

    Cowan, Benjamin M.

    2007-08-22

    Laser-driven acceleration holds great promise for significantly improving accelerating gradient. However, scaling the conventional process of structure-based acceleration in vacuum down to optical wavelengths requires a substantially different kind of structure. We require an optical waveguide that (1) is constructed out of dielectric materials, (2) has transverse size on the order of a wavelength, and (3) supports a mode with speed-of-light phase velocity in vacuum. Photonic crystals---structures whose electromagnetic properties are spatially periodic---can meet these requirements. We discuss simulated photonic crystal accelerator structures and describe their properties. We begin with a class of two-dimensional structures which serves to illustrate the design considerations and trade-offs involved. We then present a three-dimensional structure, and describe its performance in terms of accelerating gradient and efficiency. We discuss particle beam dynamics in this structure, demonstrating a method for keeping a beam confined to the waveguide. We also discuss material and fabrication considerations. Since accelerating gradient is limited by optical damage to the structure, the damage threshold of the dielectric is a critical parameter. We experimentally measure the damage threshold of silicon for picosecond pulses in the infrared, and determine that our structure is capable of sustaining an accelerating gradient of 300 MV/m at 1550 nm. Finally, we discuss possibilities for manufacturing these structures using common microfabrication techniques.

  5. Study of concrete activation with IFMIF-like neutron irradiation: Status of EAF and TENDL neutron activation cross-sections

    NASA Astrophysics Data System (ADS)

    García, Mauricio; Sauvan, Patrick; García, Raquel; Ogando, Francisco; Sanz, Javier

    2017-09-01

    The aim of this paper is to check the performance of last versions of EAF and TENDL libraries (EAF2007, EAF2010, and TENDL2014) in the prediction of concrete activation under the neutron irradiation environment expected in IFMIF, an accelerator-based neutron source conceived for fusion materials testing. For this purpose Activity and dose rate responses of three types of concrete (ITER-Bioshield kind, barite and magnetite concretes) have been studied. For these quantities, dominant nuclides and production pathways have been determined and, then, a qualitative analysis of the relevant activation cross-sections involved has been performed by comparing data from mentioned libraries with experimental data from EXFOR database. Concrete activation studies have been carried out with IFMIF-like neutron irradiation conditions using the ACAB code and EAF and TENDL libraries. The cooling times assessed are related to safety and maintenance operations, specifically 1 hour, 1 day and 12 days. Final conclusions are focused on the recommendations for the activation library to be used among those analyzed and cross-section data to be improved.

  6. Wakefields in photonic accelerator structures

    SciTech Connect

    Naranjo, B.; Andonian, G.; Arab, E.; Barber, S.; Fitzmorris, K.; Fukusawa, A.; Hoang, P.; Mahapatra, S.; O'Shea, B.; Valloni, A.; Williams, O.; Yang, C.; Rosenzweig, J. B.

    2012-12-21

    Control and manipulation of properties - such as vacuum modal confinement, spatial harmonic content, phase velocity, and group velocity - are reasons why an all-dielectric beam-driven accelerator would be expected to benefit by borrowing from the field of optical bandgap photonics. We outline the general conditions for coherent Cerenkov radiation in a photonic crystal, illustrated by three examples: two Bragg mirrors separated by a vacuum gap, a woodpile with a linear waveguide channel, and a stack of photonic slabs having a planar waveguide channel.

  7. Variable energy constant current accelerator structure

    DOEpatents

    Anderson, O.A.

    1988-07-13

    A variable energy, constant current ion beam accelerator structure is disclosed comprising an ion source capable of providing the desired ions, a pre-accelerator for establishing an initial energy level, a matching/pumping module having means for focusing means for maintaining the beam current, and at least one main accelerator module for continuing beam focus, with means capable of variably imparting acceleration to the beam so that a constant beam output current is maintained independent of the variable output energy. In a preferred embodiment, quadrupole electrodes are provided in both the matching/pumping module and the one or more accelerator modules, and are formed using four opposing cylinder electrodes which extend parallel to the beam axis and are spaced around the beam at 90/degree/ intervals with opposing electrodes maintained at the same potential. 12 figs., 3 tabs.

  8. Comparison of high group velocity accelerating structures

    SciTech Connect

    Farkas, Z.D.; Wilson, P.B.

    1987-02-01

    It is well known that waveguides with no perturbations have phase velocities greater than the velocity of light c. If the waveguide dimensions are chosen so that the phase velocity is only moderately greater than c, only small perturbations are required to reduce the phase velocity to be synchronous with a high energy particle bunch. Such a lightly loaded accelerator structure will have smaller longitudinal and transverse wake potentials and hence will lead to lower emittance growth in an accelerated beam. Since these structures are lightly loaded, their group velocities are only slightly less than c and not in the order of 0.01c, as is the case for the standard disk-loaded structures. To ascertain that the peak and average power requirements for these structures are not prohibitive, we examine the elastance and the Q for several traveling wave structures: phase slip structures, bellows-like structures, and lightly loaded disk-loaded structures.

  9. Superconducting heavy-ion accelerating structures

    SciTech Connect

    Shepard, K.W.

    1996-08-01

    This paper briefly reviews the technical history of superconducting ion-accelerating structures. Various superconducting cavities currently used and being developed for use in ion linacs are discussed. Principal parameters and operational characteristics of superconducting structures in active use at various heavy-ion facilities are described.

  10. Variable energy constant current accelerator structure

    DOEpatents

    Anderson, Oscar A.

    1990-01-01

    A variable energy, constant current ion beam accelerator structure is disclosed comprising an ion source capable of providing the desired ions, a pre-accelerator for establishing an initial energy level, a matching/pumping module having means for focusing means for maintaining the beam current, and at least one main accelerator module for continuing beam focus, with means capable of variably imparting acceleration to the beam so that a constant beam output current is maintained independent of the variable output energy. In a preferred embodiment, quadrupole electrodes are provided in both the matching/pumping module and the one or more accelerator modules, and are formed using four opposing cylinder electrodes which extend parallel to the beam axis and are spaced around the beam at 90.degree. intervals with opposing electrodes maintained at the same potential. Adjacent cylinder electrodes of the quadrupole structure are maintained at different potentials to thereby reshape the cross section of the charged particle beam to an ellipse in cross section at the mid point along each quadrupole electrode unit in the accelerator modules. The beam is maintained in focus by alternating the major axis of the ellipse along the x and y axis respectively at adjacent quadrupoles. In another embodiment, electrostatic ring electrodes may be utilized instead of the quadrupole electrodes.

  11. The grating as an accelerating structure

    SciTech Connect

    Fernow, R.C.

    1991-02-01

    This report considers the use of a diffraction grating as an accelerating structure for charged particle beams. We examine the functional dependence of the electromagnetic fields above the surface of a grating. Calculations are made of the strength of the accelerating modes for structures with {pi} and 2{pi} phase advance per period and for incident waves polarized with either the E or H vector along the grooves of the grating. We consider examples of using gratings in a laser linac and in a grating lens. We also briefly examine previous results published about this subject. 36 refs.

  12. Multi-Mode Cavity Accelerator Structure

    SciTech Connect

    Jiang, Yong; Hirshfield, Jay Leonard

    2016-11-10

    This project aimed to develop a prototype for a novel accelerator structure comprising coupled cavities that are tuned to support modes with harmonically-related eigenfrequencies, with the goal of reaching an acceleration gradient >200 MeV/m and a breakdown rate <10-7/pulse/meter. Phase I involved computations, design, and preliminary engineering of a prototype multi-harmonic cavity accelerator structure; plus tests of a bimodal cavity. A computational procedure was used to design an optimized profile for a bimodal cavity with high shunt impedance and low surface fields to maximize the reduction in temperature rise ΔT. This cavity supports the TM010 mode and its 2nd harmonic TM011 mode. Its fundamental frequency is at 12 GHz, to benchmark against the empirical criteria proposed within the worldwide High Gradient collaboration for X-band copper structures; namely, a surface electric field Esurmax< 260 MV/m and pulsed surface heating ΔTmax< 56 °K. With optimized geometry, amplitude and relative phase of the two modes, reductions are found in surface pulsed heating, modified Poynting vector, and total RF power—as compared with operation at the same acceleration gradient using only the fundamental mode.

  13. Accelerator Structure Development for NLC/GLC

    SciTech Connect

    Wang, J

    2004-03-05

    The NLC (Next Linear Collider) and GLC (Global Linear Collider) [1,2] are e{sup +}e{sup -} linear collider proposals based on room-temperature accelerator technology--so called ''warm machines'' in comparison with the TESLA ''cold machine'' that is based on superconducting accelerator technology. There have been two major challenges in developing X-band (11.4 GHz) accelerator structures for the GLC/NLC. The first is to demonstrate stable, long-term operation at the high gradient (65 MV/m) that is required to optimize the machine cost. The second is to strongly suppress the beam induced long-range wakefields, which is required to achieve high luminosity. The development of high gradient structures has been a high priority in recent years. Nearly thirty X-band structures with various rf parameters, cavity shapes and coupler types have been fabricated and tested since 2000. This program has been a successful collaborative effort among groups at SLAC, KEK, FNAL and other labs. A summary of the main achievements and experiences are presented in this paper as well as a status report on the structure design, high power performance, manufacturing techniques, and other structure related issues.

  14. IFMIF - International Fusion Materials Irradiation Facility Conceptual Design Activity/Interim Report

    SciTech Connect

    Rennich, M.J.

    1995-12-01

    Environmental acceptability, safety, and economic viability win ultimately be the keys to the widespread introduction of fusion power. This will entail the development of radiation- resistant and low- activation materials. These low-activation materials must also survive exposure to damage from neutrons having an energy spectrum peaked near 14 MeV with annual radiation doses in the range of 20 displacements per atom (dpa). Testing of candidate materials, therefore, requires a high-flux source of high energy neutrons. The problem is that there is currently no high-flux source of neutrons in the energy range above a few MeV. The goal, is therefore, to provide an irradiation facility for use by fusion material scientists in the search for low-activation and damage-resistant materials. An accellerator-based neutron source has been established through a number of international studies and workshops` as an essential step for materials development and testing. The mission of the International Fusion Materials Irradiation Facility (IFMIF) is to provide an accelerator-based, deuterium-lithium (D-Li) neutron source to produce high energy neutrons at sufficient intensity and irradiation volume to test samples of candidate materials up to about a full lifetime of anticipated use in fusion energy reactors. would also provide calibration and validation of data from fission reactor and other accelerator-based irradiation tests. It would generate material- specific activation and radiological properties data, and support the analysis of materials for use in safety, maintenance, recycling, decommissioning, and waste disposal systems.

  15. Vacuum design for the disk-and-washer accelerator structure

    SciTech Connect

    Ruhe, J.R.; Hansborough, L.D.

    1982-02-01

    The disk-and-washer (DAW) accelerator structure is being developed for several applications. Because of its complicated geometry and newness, vacuum calculations for the DAW accelerator structure are not yet formalized. The applicable vacuum equations for this structure are presented and correlations for it have been made with the vacuum data from the Clinton P. Anderson Meson Physics Facility side-coupled accelerator structure. A calculation is presented for the DAW structure proposed for the Pion Generator for Medical Irradiations (PIGMI) accelerator.

  16. Advanced accelerator and mm-wave structure research at LANL

    SciTech Connect

    Simakov, Evgenya Ivanovna

    2016-06-22

    This document outlines acceleration projects and mm-wave structure research performed at LANL. The motivation for PBG research is described first, with reference to couplers for superconducting accelerators and structures for room-temperature accelerators and W-band TWTs. These topics are then taken up in greater detail: PBG structures and the MIT PBG accelerator; SRF PBG cavities at LANL; X-band PBG cavities at LANL; and W-band PBG TWT at LANL. The presentation concludes by describing other advanced accelerator projects: beam shaping with an Emittance Exchanger, diamond field emitter array cathodes, and additive manufacturing of novel accelerator structures.

  17. Accelerator Structure Bead Pull Measurement at SLAC

    SciTech Connect

    Lewandowski, J.R.; Bowden, G.; Miller, R.H.; Wang, J.W.; /SLAC

    2005-05-13

    Microwave measurement and tuning of accelerator structures are important issues for the current and next generation of high energy physics machines. Application of these measurements both before and after high power processing can reveal information about the structure but may be misinterpreted if measurement conditions are not carefully controlled. For this reason extensive studies to characterize the microwave measurements have been made at SLAC. For the bead pull a reproducible measurement of less than 1 degree of phase accuracy in total phase drift is needed in order to resolve issues such as phase changes due to structure damage during high power testing. Factors contributing to measurement errors include temperature drift, mechanical vibration, and limitations of measurement equipment such as the network analyzer. Results of this continuing effort will be presented.

  18. Planar Accelerator Structures for Millimeter Wavelengths

    SciTech Connect

    Palmer, Dennis

    2000-10-18

    The fabrication of a muffin-tin planar accelerator structure for operation in the 90 GHz range is discussed in Reference. [1]. Fabrication problems subsequently encountered led us to consider an alternative structure, a structure which can be thought of as a muffin-tin with the sides removed and replaced by a pair of side chambers which act as side terminations (Fig. 1). With the side chambers removed, the structure when viewed from the side presents two periodic arrays of vanes facing one another from above and below the beam plane and which extend towards the beam plane from upper and lower plane metallic surfaces. The vane pairs are the analogs of the beam iris in cylindrical structures, and the space between the irises and terminated by the upper and lower plane metallic surfaces correspond to the cavities. Because the general appearance of this view is zipper like, we will refer to the structure as the ''zipper'' structure. The side chambers are envisaged as extending with uniform cross section from the input to the output cavities.

  19. Design and analysis of the lithium target system for the International Fusion Materials Irradiation Facility (IFMIF)

    SciTech Connect

    Hua, T.; Smith, D.; Hassanein, A.; Gomes, I.

    1995-09-01

    Three lithium target design options are being evaluated for the IFMIF. The impact of various requirements on material selection, lifetime, operation and maintenance are discussed. Analysis for the free jet option is presented. Key aspects include jet stability, thermal and nuclear responses.

  20. Transmutation behaviour of Eurofer under irradiation in the IFMIF test facility and fusion power reactors

    NASA Astrophysics Data System (ADS)

    Fischer, U.; Simakov, S. P.; Wilson, P. P. H.

    2004-08-01

    The transmutation behaviour of the low activation steel Eurofer was analysed for irradiation simulations in the high flux test module (HFTM) of the International Fusion Material Irradiation Facility (IFMIF) neutron source and the first wall of a typical fusion power reactor (FPR) employing helium cooled lithium lead (HCLL) and pebble bed (HCPB) blankets. The transmutation calculations were conducted with the analytical and laplacian adaptive radioactivity analysis (ALARA) code and IEAF-2001 data for the IFMIF and the EASY-2003 system for the fusion power reactor (FPR) irradiations. The analyses showed that the transmutation of the main constituents of Eurofer, including iron and chromium, is not significant. Minor constituents such as Ti, V and Mn increase by 5-15% per irradiation year in the FPR and by 10-35% in the IFMIF HFTM. Other minor constituents such as B, Ta, and W show a different transmutation behaviour resulting in different elemental compositions of the Eurofer steel after high fluence irradiations in IFMIF and fusion power reactors.

  1. Micromechanical structures and microelectronics for acceleration sensing

    NASA Astrophysics Data System (ADS)

    Davies, Brady R.; Montague, Stephen; Smith, James H.; Lemkin, Mark

    1997-09-01

    MEMS is an enabling technology that may provide low-cost devices capable of sensing motion in a reliable and accurate manner. This paper describes work in MEMS accelerometer development at Sandia National Laboratories. This work leverages a process for integrating both the micromechanical structures and microelectronics circuitry of a MEMS accelerometer on the same chip. The design and test results of an integrated MEMS high-g accelerometer will be detailed. Additionally a design for a high-g fuse component (low-G or approximately equals 25 G accelerometer) will be discussed in the paper (where 1 G approximately equals 9.81 m/s). In particular, a design team at Sandia was assembled to develop a new micromachined silicon accelerometer which would be capable of surviving and measuring high-g shocks. Such a sensor is designed to be cheaper and more reliable than currently available sensors. A promising design for a suspended plate mass sensor was developed and the details of that design along with test data will be documented in the paper. Future development in this area at Sandia will focus on implementing accelerometers capable of measuring 200 kilo-g accelerations. Accelerometer development at Sandia will also focus on multi-axis acceleration measurement with integrated microelectronics.

  2. Micromechanical structures and microelectronics for acceleration sensing

    SciTech Connect

    Davies, B.R.; Montague, S.; Smith, J.H.; Lemkin, M.

    1997-08-01

    MEMS is an enabling technology that may provide low-cost devices capable of sensing motion in a reliable and accurate manner. This paper describes work in MEMS accelerometer development at Sandia National Laboratories. This work leverages a process for integrating both the micromechanical structures and microelectronis circuitry of a MEMS accelerometer on the same chip. The design and test results of an integrated MEMS high-g accelerometer will be detailed. Additionally a design for a high-g fuse component (low-G or {approx} 25 G accelerometer) will be discussed in the paper (where 1 G {approx} 9.81 m/s). In particular, a design team at Sandia was assembled to develop a new micromachined silicon accelerometer which would be capable of surviving and measuring high-g shocks. Such a sensor is designed to be cheaper and more reliable than currently available sensors. A promising design for a suspended plate mass sensor was developed and the details of that design along with test data will be documented in the paper. Future development in this area at Sandia will focus on implementing accelerometers capable of measuring 200 kilo-g accelerations. Accelerometer development at Sandia will also focus on multi-axis acceleration measurement with integrated microelectronics.

  3. Hybrid dielectric and iris-loaded periodic accelerating structure

    NASA Astrophysics Data System (ADS)

    Zou, Peng; Xiao, Liling; Sun, Xiang; Gai, Wei; Wong, Thomas

    2001-08-01

    One disadvantage of conventional iris-loaded accelerating structures is the high ratio of the peak surface electric field to the peak axial electric field useful for accelerating a beam. Typically this ratio Es/Ea⩾2. The high surface electric field relative to the accelerating gradient may prove to be a limitation for realizing technologies for very high gradient accelerators. In this article, we present a scheme that uses a hybrid dielectric and iris-loaded periodic structure to reduce Es/Ea to near unity, while the shunt impedance per unit length r and the quality factor Q compare favorably with conventional metallic structures. The analysis based on MAFIA simulations of such structures shows that we can lower the peak surface electric field close to the accelerating gradient while maintaining high acceleration efficiency as measured by r/Q. Numerical examples of X-band hybrid accelerating structures are given.

  4. A hybrid dielectric and iris loaded periodic accelerating structure.

    SciTech Connect

    Zou, P.; Xiao, L.; Sun, X.; Gai, W.

    2001-07-17

    One disadvantage of conventional iris-loaded accelerating structures is the high ratio of the peak surface electric field to the peak axial electric field useful for accelerating a beam. Typically this ratio E{sub s}/E{sub a} {ge} 2. The high surface electric field relative to the accelerating gradient may prove to be a limitation for realizing technologies for very high gradient accelerators. In this paper, we present a scheme that uses a hybrid dielectric and iris loaded periodic structure to reduce E{sub s}/E{sub a} to near unity, while the shunt impedance per unit length r and the quality factor Q compare favorably with conventional metallic structures. The analysis based on MAFIA simulations of such structures shows that we can lower the peak surface electric field close to the accelerating gradient while maintaining high acceleration efficiency as measured by r/Q. Numerical examples of X-band hybrid accelerating structures are given.

  5. Locating Bound Structures in the Accelerating Universe

    NASA Astrophysics Data System (ADS)

    Pearson, David; Batuski, D. J.

    2013-01-01

    Given the overwhelming evidence of the universe’s accelerating expansion, the question of what structures are gravitationally bound becomes one of utmost interest. Dunner et al. 2006 (D06) and Busha et al. 2003 (B03) set out to answer this question analytically, and they arrived at fairly different answers owing to the differences in their assumptions of velocities at the present epoch. Applying their criteria to different superclusters, it’s possible to make predictions about what structures may be bound. We apply the criteria of D06 and B03 to the Aquarius, Microscopium, Corona Borealis, and Shapley superclusters to make predictions about what structures might be bound and compare with the results of simple N-body simulations to determine which method is a better predictor and to determine the likelihood that parts or all of the superclusters listed above are bound. We find that D06 tend to predict more structure to be bound than B03, and the results of the N-body simulations usually lie somewhere in between the two sets of predictions. Observational evidence, and simulation data suggests that pairs of clusters in Aquarius and Microscopium are gravitationally bound, and that Shapley contains a large complex of clusters that are bound, along with some additional bound pairs. The likelihood that any of the clusters in Corona Borealis are bound to one another is very small, contrary to the claims of Small et al. 1998, who claimed that the entire supercluster is likely gravitationally bound. Busha M. T., Adams F. C., Wechsler R. H., Evrard A. E., 2003, ApJ, 596, 713 Dunner R., Araya P. A., Meza A., Reisenegger A., 2006, MNRAS, 306, 803 Small T. A., Ma C., Sargent W. L. W., Hamilton D., 1998, ApJ, 492, 45

  6. Progress Toward NLC/GLC Prototype Accelerator Structures

    SciTech Connect

    Wang, J

    2004-09-13

    The accelerator structure groups for NLC (Next Linear Collider) and GLC (Global Linear Colliders) have successfully collaborated on the research and development of a major series of advanced accelerator structures based on room-temperature technology at X-band frequency. The progress in design, simulation, microwave measurement and high gradient tests are summarized in this paper. The recent effort in design and fabrication of the accelerator structure prototype for the main linac is presented in detail including HOM (High Order Mode) suppression and design of HOM couplers and fundamental mode couplers, optimized accelerator cavities as well as plans for future structures.

  7. The fabrication of millimeter-wavelength accelerating structures

    SciTech Connect

    Chou, P.J.; Bowden, G.B.; Copeland, M.R.

    1996-11-01

    There is a growing interest in the development of high gradient ({ge} 1 GeV/m) accelerating structures. The need for high gradient acceleration based on current microwave technology requires the structures to be operated in the millimeter wavelength. Fabrication of accelerating structures at millimeter scale with sub-micron tolerances poses great challenges. The accelerating structures impose strict requirements on surface smoothness and finish to suppress field emission and multipactor effects. Various fabrication techniques based on conventional machining and micromachining have been evaluated and tested. These will be discussed and measurement results presented.

  8. S-band accelerating structures for the PAL-XFEL

    NASA Astrophysics Data System (ADS)

    Lee, Heung-Soo; Park, Young Jung; Joo, Young-Do; Heo, Hoon; Heo, Jinyul; Kim, Sang-Hee; Park, Soung-Soo; Hwang, Woon Ha; Kang, Heung-Sik; Kim, Kwang-woo; Ko, In-Soo; Oh, Kyoung-Min; Noh, Sung-Joo; Bak, Yong Hwan; Matsumoto, Hiroshi

    2015-02-01

    One hundred seventy-two accelerating structures are required for the Pohang Accelerator Laboratory X-ray free-electron laser's (PAL-XFEL's) 10-GeV main linear accelerator. So far, we have purchased 80 structures from Mitsubishi Heavy Industry (MHI), which have quasi-symmetric couplers in the accelerating structure to reduce the quadruple and the sextuple components of the electric field in the coupling cavity. High-power tests have been conducted for the first structure of the MHI structure, and Research Instruments (RI) has developed a 3-m long accelerating structure that has an operating frequency of 2856 MHz and in/out couplers of quasi-symmetric racetrack shape for the PAL-XFEL linear accelerator. This structure also has been tested by PAL and RI in the Pohang accelerator laboratory (PAL) to check the maximum available electric field gradient. We will describe the test results of these structures and the current status for the fabrication of the other accelerating structures in this paper.

  9. R&D of Accelerator Structures at SLAC

    SciTech Connect

    Wang, J.W.; /SLAC

    2007-01-17

    The research activities for accelerator structures at SLAC are reviewed including the achievement via the main linac design for the Next Linear Collider (NLC), the program adjustment after the decision of the International Linear Collider (ILC) to be based on superconducting technology, and the work progress for the ILC, photon science at SLAC and basic accelerator structure studies.

  10. Method for computationally efficient design of dielectric laser accelerator structures.

    PubMed

    Hughes, Tyler; Veronis, Georgios; Wootton, Kent P; Joel England, R; Fan, Shanhui

    2017-06-26

    Dielectric microstructures have generated much interest in recent years as a means of accelerating charged particles when powered by solid state lasers. The acceleration gradient (or particle energy gain per unit length) is an important figure of merit. To design structures with high acceleration gradients, we explore the adjoint variable method, a highly efficient technique used to compute the sensitivity of an objective with respect to a large number of parameters. With this formalism, the sensitivity of the acceleration gradient of a dielectric structure with respect to its entire spatial permittivity distribution is calculated by the use of only two full-field electromagnetic simulations, the original and 'adjoint'. The adjoint simulation corresponds physically to the reciprocal situation of a point charge moving through the accelerator gap and radiating. Using this formalism, we perform numerical optimizations aimed at maximizing acceleration gradients, which generate fabricable structures of greatly improved performance in comparison to previously examined geometries.

  11. Manifold damping of the NLC detuned accelerating structure

    SciTech Connect

    Kroll, N.; Thompson, K.; Bane, K.; Ko, K.; Miller, R.; Ruth, R.; Gluckstern, R.

    1994-09-01

    In order to investigate the reappearance of the HOM wakefield of a detuned accelerator structure and relax tolerance requirements, we propose to provide low level damping by coupling all cavities to several identical and symmetrically located waveguides (manifolds) which run parallel to each accelerator structure and are terminated at each end by matched loads. The waveguides are designed such that all modes which couple to the acceleration mode are non-propagating at the acceleration mode frequency. Hence the coupling irises can be designed to provide large coupling to higher frequency modes without damping the acceleration mode. Because the higher order modes are detuned, they are localized and have a broad spectrum of phase velocities of both signs. They are therefore capable of coupling effectively to all propagating modes in the waveguides. Methods of analyzing and results obtained for the very complex system of modes in the accelerating structure and manifolds are presented.

  12. Compact Couplers for Photonic Crystal Laser-Driven Accelerator Structures

    SciTech Connect

    Cowan, Benjamin; Lin, M.C.; Schwartz, Brian; Byer, Robert; McGuinness, Christopher; Colby, Eric; England, Robert; Noble, Robert; Spencer, James; /SLAC

    2012-07-02

    Photonic crystal waveguides are promising candidates for laser-driven accelerator structures because of their ability to confine a speed-of-light mode in an all-dielectric structure. Because of the difference between the group velocity of the waveguide mode and the particle bunch velocity, fields must be coupled into the accelerating waveguide at frequent intervals. Therefore efficient, compact couplers are critical to overall accelerator efficiency. We present designs and simulations of high-efficiency coupling to the accelerating mode in a three-dimensional photonic crystal waveguide from a waveguide adjoining it at 90{sup o}. We discuss details of the computation and the resulting transmission. We include some background on the accelerator structure and photonic crystal-based optical acceleration in general.

  13. Manifold damping of the NLC detuned accelerating structure

    NASA Astrophysics Data System (ADS)

    Kroll, N.; Thompson, K.; Bane, K.; Gluckstern, R.; Ko, K.; Miller, R.; Ruth, R.

    1995-06-01

    In order to mitigate the reappearance of the HOM wakefield of a detuned accelerator structure and relax tolerance requirements, we propose to provide low level damping by coupling all cavities to several identical and symmetrically located waveguides (manifolds) which run parallel to each accelerator structure and are terminated at each end by matched loads. The waveguides are designed such that all modes which couple to the acceleration mode are non-propagating at the acceleration mode frequency. Hence the coupling irises can be designed to provide large coupling to higher frequency modes without damping the acceleration mode. Because the higher order modes are detuned, they are localized and have a broad spectrum of phase velocities of both signs. They are therefore capable of coupling effectively to all propagating modes in the waveguides. Methods of analyzing and results obtained for the very complex system of modes in the accelerating structure and manifolds are presented.

  14. Particle accelerations and current structures of Weibel and Filamentation instabilities

    NASA Astrophysics Data System (ADS)

    Ryu, C. M.; Huynh, C. T.

    2015-12-01

    Particle accelerations of the Wibel instability (WI) and the Filamentation instability(FI) are studied by using PIC simuations, comparing them side-by-side. Although two instabilities are almost identical in the linear growth phase, significant differences are found in the nonlinear phase in their particle accelerations and current structures. The FI shows enhanced electron acceleration, whereas particle acceleration is almost absent in the WI. The different particle accelerations between the FI and the WI seem to be associated with their different current structures; a hollow electron current structure for the FI and a center filled current structure for that of the WI. Different electron distributions seem to bring in different current filament structures, eventually leading to different magnetic characteristics.

  15. IFMIF, International Fusion Materials Irradiation Facility conceptual design activity cost report

    SciTech Connect

    Rennich, M.J.

    1996-12-01

    This report documents the cost estimate for the International Fusion Materials Irradiation Facility (IFMIF) at the completion of the Conceptual Design Activity (CDA). The estimate corresponds to the design documented in the Final IFMIF CDA Report. In order to effectively involve all the collaborating parties in the development of the estimate, a preparatory meeting was held at Oak Ridge National Laboratory in March 1996 to jointly establish guidelines to insure that the estimate was uniformly prepared while still permitting each country to use customary costing techniques. These guidelines are described in Section 4. A preliminary cost estimate was issued in July 1996 based on the results of the Second Design Integration Meeting, May 20--27, 1996 at JAERI, Tokai, Japan. This document served as the basis for the final costing and review efforts culminating in a final review during the Third IFMIF Design Integration Meeting, October 14--25, 1996, ENEA, Frascati, Italy. The present estimate is a baseline cost estimate which does not apply to a specific site. A revised cost estimate will be prepared following the assignment of both the site and all the facility responsibilities.

  16. Advanced accelerating structures and their interaction with electron beams.

    SciTech Connect

    Gai, W.; High Energy Physics

    2008-01-01

    In this paper, we give a brief description of several advanced accelerating structures, such as dielectric loaded waveguides, photonic band gap, metamaterials and improved iris-loaded cavities. We describe wakefields generated by passing high current electron beams through these structures, and applications of wakefields to advanced accelerator schemes. One of the keys to success for high gradient wakefield acceleration is to develop high current drive beam sources. As an example, the high current RF photo injector at the Argonne Wakefield Accelerator, passed a {approx}80 nC electron beam through a high gradient dielectric loaded structure to achieve a 100 MV/m gradient. We will summarize recent related experiments on beam-structure interactions and also discuss high current electron beam generation and propagation and their applications to wakefield acceleration.

  17. Advanced Accelerating Structures and Their Interaction with Electron Beams

    SciTech Connect

    Gai Wei

    2009-01-22

    In this paper, we give a brief description of several advanced accelerating structures, such as dielectric loaded waveguides, photonic band gap, metamaterials and improved iris-loaded cavities. We describe wakefields generated by passing high current electron beams through these structures, and applications of wakefields to advanced accelerator schemes. One of the keys to success for high gradient wakefield acceleration is to develop high current drive beam sources. As an example, the high current RF photo injector at the Argonne Wakefield Accelerator, passed a {approx}80 nC electron beam through a high gradient dielectric loaded structure to achieve a 100 MV/m gradient. We will summarize recent related experiments on beam-structure interactions and also discuss high current electron beam generation and propagation and their applications to wakefield acceleration.

  18. High gradient tests of metallic mm-wave accelerating structures

    NASA Astrophysics Data System (ADS)

    Dal Forno, Massimo; Dolgashev, Valery; Bowden, Gordon; Clarke, Christine; Hogan, Mark; McCormick, Doug; Novokhatski, Alexander; O'Shea, Brendan; Spataro, Bruno; Weathersby, Stephen; Tantawi, Sami G.

    2017-08-01

    This paper explores the physics of vacuum rf breakdowns in high gradient mm-wave accelerating structures. We performed a series of experiments with 100 GHz and 200 GHz metallic accelerating structures, at the Facility for Advanced Accelerator Experimental Tests (FACET) at the SLAC National Accelerator Laboratory. This paper presents the experimental results of rf tests of 100 GHz travelling-wave accelerating structures, made of hard copper-silver alloy. The results are compared with pure hard copper structures. The rf fields were excited by the FACET ultra-relativistic electron beam. The accelerating structures have open geometries, 10 cm long, composed of two halves separated by a variable gap. The rf frequency of the fundamental accelerating mode depends on the gap size and can be changed from 90 GHz to 140 GHz. The measured frequency and pulse length are consistent with our simulations. When the beam travels off-axis, a deflecting field is induced in addition to the decelerating longitudinal field. We measured the deflecting forces by observing the displacement of the electron bunch and used this measurement to verify the expected accelerating gradient. We present the first quantitative measurement of rf breakdown rates in 100 GHz copper-silver accelerating structure, which was 10-3 per pulse, with peak electric field of 0.42 GV/m, an accelerating gradient of 127 MV/m, at a pulse length of 2.3 ns. The goal of our studies is to understand the physics of gradient limitations in order to increase the energy reach of future accelerators.

  19. High gradient tests of metallic mm-wave accelerating structures

    DOE PAGES

    Dal Forno, Massimo; Dolgashev, Valery; Bowden, Gordon; ...

    2017-05-10

    This study explores the physics of vacuum rf breakdowns in high gradient mm-wave accelerating structures. We performed a series of experiments with 100 GHz and 200 GHz metallic accelerating structures, at the Facility for Advanced Accelerator Experimental Tests (FACET) at the SLAC National Accelerator Laboratory. This paper presents the experimental results of rf tests of 100 GHz travelling-wave accelerating structures, made of hard copper-silver alloy. The results are compared with pure hard copper structures. The rf fields were excited by the FACET ultra-relativistic electron beam. The accelerating structures have open geometries, 10 cm long, composed of two halves separated bymore » a variable gap. The rf frequency of the fundamental accelerating mode depends on the gap size and can be changed from 90 GHz to 140 GHz. The measured frequency and pulse length are consistent with our simulations. When the beam travels off-axis, a deflecting field is induced in addition to the decelerating longitudinal field. We measured the deflecting forces by observing the displacement of the electron bunch and used this measurement to verify the expected accelerating gradient. We present the first quantitative measurement of rf breakdown rates in 100 GHz copper-silver accelerating structure, which was 10–3 per pulse, with peak electric field of 0.42 GV/m, an accelerating gradient of 127 MV/m, at a pulse length of 2.3 ns. The goal of our studies is to understand the physics of gradient limitations in order to increase the energy reach of future accelerators.« less

  20. Multipactor Physics, Acceleration, and Breakdown in Dielectric-Loaded Accelerating Structures

    SciTech Connect

    Fischer, Richard P.; Gold, Steven H.

    2016-07-01

    The objective of this 3-year program is to study the physics issues associated with rf acceleration in dielectric-loaded accelerating (DLA) structures, with a focus on the key issue of multipactor loading, which has been found to cause very significant rf power loss in DLA structures whenever the rf pulsewidth exceeds the multipactor risetime (~10 ns). The experiments are carried out in the X-band magnicon laboratory at the Naval Research Laboratory (NRL) in collaboration with Argonne National Laboratory (ANL) and Euclid Techlabs LLC, who develop the test structures with support from the DoE SBIR program. There are two main elements in the research program: (1) high-power tests of DLA structures using the magnicon output (20 MW @11.4 GHz), and (2) tests of electron acceleration in DLA structures using relativistic electrons from a compact X-band accelerator. The work during this period has focused on a study of the use of an axial magnetic field to suppress multipactor in DLA structures, with several new high power tests carried out at NRL, and on preparation of the accelerator for the electron acceleration experiments.

  1. Investigations of the plasma and structure based accelerators

    SciTech Connect

    Shvets, Gennady

    2012-08-30

    The objective of our research during the reported period was three-fold: (a) theoretical investigation of novel mechanisms of injection into laser wake field accelerators; (b) theoretical investigation of single-shot frequency domain diagnostics of relativistic plasma wakes, specifically in the context of spatio-temporal evolution of the plasma bubble;(c) experimental and theoretical investigation of laser-driven accelerating structure, specifically in the context of the Surface Wave Accelerator Based on SiC (SWABSIC).

  2. Helical Pulse Line Structures for Ion Acceleration

    SciTech Connect

    Briggs, R.J.; Reginato, L.L.; Waldron, W.L.

    2005-05-01

    The basic concept of the ''Pulse Line Ion Accelerator'' is presented, where pulse power sources create a ramped traveling wave voltage pulse on a helical pulse line. Ions can surf on this traveling wave and achieve energy gains much larger than the peak applied voltage. Tapered and untapered lines are compared, and a transformer coupling technique for launching the wave is described.

  3. ELECTROMAGNETIC SIMULATIONS OF LINEAR PROTON ACCELERATOR STRUCTURES USING DIELECTRIC WALL ACCELERATORS

    SciTech Connect

    Nelson, S; Poole, B; Caporaso, G

    2007-06-15

    Proton accelerator structures for medical applications using Dielectric Wall Accelerator (DWA) technology allow for the utilization of high electric field gradients on the order of 100 MV/m to accelerate the proton bunch. Medical applications involving cancer therapy treatment usually desire short bunch lengths on the order of hundreds of picoseconds in order to limit the extent of the energy deposited in the tumor site (in 3D space, time, and deposited proton charge). Electromagnetic simulations of the DWA structure, in combination with injections of proton bunches have been performed using 3D finite difference codes in combination with particle pushing codes. Electromagnetic simulations of DWA structures includes these effects and also include the details of the switch configuration and how that switch time affects the electric field pulse which accelerates the particle beam.

  4. Experimental Demonstration of Wakefield Acceleration in a Tunable Dielectric Loaded Accelerating Structure

    SciTech Connect

    Jing, C.; Antipov, S.; Kanareykin, A.; Schoessow, P.; Power, J. G.; Conde, M.; Liu, W.; Gai, W.

    2011-04-22

    We report on a collinear wakefield experiment using the first tunable dielectric loaded accelerating structure. By introducing an extra layer of nonlinear ferroelectric, which has a dielectric constant sensitive to temperature and dc bias, the frequency of a dielectric loaded accelerating structure can be tuned. During the experiment, the energy of a witness bunch at a fixed delay with respect to the drive beam was measured while the temperature of the structure was scanned over a 50 deg. C range. The energy change corresponded to a change of more than half of the nominal structure wavelength.

  5. Experimental demonstration of Wakefield acceleration in a tunable dielectric loaded accelerating structure.

    SciTech Connect

    Liu, W.; Power, J. G.; Conde, M.; Antipov, S.; Schoessow, P.; Gai, W.; Jing, C.; Kanareykin, A.; Schoessow, P.

    2011-04-21

    We report on a collinear wakefield experiment using the first tunable dielectric loaded accelerating structure. By introducing an extra layer of nonlinear ferroelectric, which has a dielectric constant sensitive to temperature and dc bias, the frequency of a dielectric loaded accelerating structure can be tuned. During the experiment, the energy of a witness bunch at a fixed delay with respect to the drive beam was measured while the temperature of the structure was scanned over a 50 C range. The energy change corresponded to a change of more than half of the nominal structure wavelength.

  6. High-performance computing in accelerating structure design and analysis

    NASA Astrophysics Data System (ADS)

    Li, Zenghai; Folwell, Nathan; Ge, Lixin; Guetz, Adam; Ivanov, Valentin; Kowalski, Marc; Lee, Lie-Quan; Ng, Cho-Kuen; Schussman, Greg; Stingelin, Lukas; Uplenchwar, Ravindra; Wolf, Michael; Xiao, Liling; Ko, Kwok

    2006-03-01

    Future high-energy accelerators such as the Next Linear Collider (NLC) will accelerate multi-bunch beams of high current and low emittance to obtain high luminosity, which put stringent requirements on the accelerating structures for efficiency and beam stability. While numerical modeling has been quite standard in accelerator R&D, designing the NLC accelerating structure required a new simulation capability because of the geometric complexity and level of accuracy involved. Under the US DOE Advanced Computing initiatives (first the Grand Challenge and now SciDAC), SLAC has developed a suite of electromagnetic codes based on unstructured grids and utilizing high-performance computing to provide an advanced tool for modeling structures at accuracies and scales previously not possible. This paper will discuss the code development and computational science research (e.g. domain decomposition, scalable eigensolvers, adaptive mesh refinement) that have enabled the large-scale simulations needed for meeting the computational challenges posed by the NLC as well as projects such as the PEP-II and RIA. Numerical results will be presented to show how high-performance computing has made a qualitative improvement in accelerator structure modeling for these accelerators, either at the component level (single cell optimization), or on the scale of an entire structure (beam heating and long-range wakefields).

  7. High-Performance Computing in Accelerating Structure Design And Analysis

    SciTech Connect

    Li, Z.H.; Folwell, N.; Ge, Li-Xin; Guetz, A.; Ivanov, V.; Kowalski, M.; Lee, L.Q.; Ng, C.K.; Schussman, G.; Stingelin, L.; Uplenchwar, R.; Wolf, M.; Xiao, L.L.; Ko, K.; /SLAC /PSI, Villigen /Illinois U., Urbana

    2006-06-27

    Future high-energy accelerators such as the Next Linear Collider (NLC) will accelerate multi-bunch beams of high current and low emittance to obtain high luminosity, which put stringent requirements on the accelerating structures for efficiency and beam stability. While numerical modeling has been quite standard in accelerator R&D, designing the NLC accelerating structure required a new simulation capability because of the geometric complexity and level of accuracy involved. Under the US DOE Advanced Computing initiatives (first the Grand Challenge and now SciDAC), SLAC has developed a suite of electromagnetic codes based on unstructured grids and utilizing high performance computing to provide an advanced tool for modeling structures at accuracies and scales previously not possible. This paper will discuss the code development and computational science research (e.g. domain decomposition, scalable eigensolvers, adaptive mesh refinement) that have enabled the large-scale simulations needed for meeting the computational challenges posed by the NLC as well as projects such as the PEP-II and RIA. Numerical results will be presented to show how high performance computing has made a qualitative improvement in accelerator structure modeling for these accelerators, either at the component level (single cell optimization), or on the scale of an entire structure (beam heating and long range wakefields).

  8. Hybrid dielectric and iris-loaded periodic accelerating structure

    SciTech Connect

    Zou, Peng; Xiao, Liling; Sun, Xiang; Gai, Wei; Wong, Thomas

    2001-08-15

    One disadvantage of conventional iris-loaded accelerating structures is the high ratio of the peak surface electric field to the peak axial electric field useful for accelerating a beam. Typically this ratio E{sub s}/E{sub a}{>=}2. The high surface electric field relative to the accelerating gradient may prove to be a limitation for realizing technologies for very high gradient accelerators. In this article, we present a scheme that uses a hybrid dielectric and iris-loaded periodic structure to reduce E{sub s}/E{sub a} to near unity, while the shunt impedance per unit length r and the quality factor Q compare favorably with conventional metallic structures. The analysis based on MAFIA simulations of such structures shows that we can lower the peak surface electric field close to the accelerating gradient while maintaining high acceleration efficiency as measured by r/Q. Numerical examples of X-band hybrid accelerating structures are given. {copyright} 2001 American Institute of Physics.

  9. ELECTROMAGNETIC SIMULATIONS OF DIELECTRIC WALL ACCELERATOR STRUCTURES FOR ELECTRON BEAM ACCELERATION

    SciTech Connect

    Nelson, S D; Poole, B R

    2005-05-05

    Dielectric Wall Accelerator (DWA) technology incorporates the energy storage mechanism, the switching mechanism, and the acceleration mechanism for electron beams. Electromagnetic simulations of DWA structures includes these effects and also details of the switch configuration and how that switch time affects the electric field pulse which accelerates the particle beam. DWA structures include both bi-linear and bi-spiral configurations with field gradients on the order of 20MV/m and the simulations include the effects of the beampipe, the beampipe walls, the DWA High Gradient Insulator (HGI) insulating stack, wakefield impedance calculations, and test particle trajectories with low emittance gain. Design trade-offs include the transmission line impedance (typically a few ohms), equilibration ring optimization, driving switch inductances, and layer-to-layer coupling effects and the associated affect on the acceleration pulse's peak value.

  10. Prototyping high-gradient mm-wave accelerating structures

    NASA Astrophysics Data System (ADS)

    Nanni, Emilio A.; Dolgashev, Valery A.; Haase, Andrew; Neilson, Jeffrey; Tantawi, Sami; Schaub, Samuel C.; Temkin, Richard J.; Spataro, Bruno

    2017-07-01

    We present single-cell accelerating structures designed for high-gradient testing at 110 GHz. The purpose of this work is to study the basic physics of ultrahigh vacuum RF breakdown in high-gradient RF accelerators. The accelerating structures are π-mode standing-wave cavities fed with a TM01 circular waveguide. The structures are fabricated using precision milling out of two metal blocks, and the blocks are joined with diffusion bonding and brazing. The impact of fabrication and joining techniques on the cell geometry and RF performance will be discussed. First prototypes had a measured Q0 of 2800, approaching the theoretical design value of 3300. The geometry of these accelerating structures are as close as practical to singlecell standing-wave X-band accelerating structures more than 40 of which were tested at SLAC. This wealth of X-band data will serve as a baseline for these 110 GHz tests. The structures will be powered with short pulses from a MW gyrotron oscillator. RF power of 1 MW may allow an accelerating gradient of 400 MeV/m to be reached.

  11. Blind protein structure prediction using accelerated free-energy simulations

    PubMed Central

    Perez, Alberto; Morrone, Joseph A.; Brini, Emiliano; MacCallum, Justin L.; Dill, Ken A.

    2016-01-01

    We report a key proof of principle of a new acceleration method [Modeling Employing Limited Data (MELD)] for predicting protein structures by molecular dynamics simulation. It shows that such Boltzmann-satisfying techniques are now sufficiently fast and accurate to predict native protein structures in a limited test within the Critical Assessment of Structure Prediction (CASP) community-wide blind competition. PMID:27847872

  12. EM Structure-Based Accelerators Working Group Summary

    NASA Astrophysics Data System (ADS)

    Kimura, W. D.; Lidia, S. M.

    2004-12-01

    This Working Group (WG) focused on EM Structure-Based Accelerators, which covers a broad area of mechanisms and experiments. Topics covered included dielectric wakefield accelerators (DWA), photonic bandgap accelerators (PBGA), inverse free electron lasers (IFEL), vacuum laser accelerators (VLA), other novel schemes, and supporting analysis and modeling. In addition, this WG was tasked at the Workshop with developing conceptual (strawman) designs for a 1-GeV accelerator system based upon any of the experimentally-proven approaches covered in this WG. Two strawmen designs were developed based upon IFELs and DWAs. The presentations given and strawmen designs indicate great progress has been made in many areas. Proof-of-principle experiments will occur shortly in PBGA and VLA. Other well-proven devices, such as IFELs, are becoming accepted as "workhorse" providers of microbunches.

  13. Development of X-Band Dielectric-Loaded Accelerating Structures

    SciTech Connect

    Gold, S. H.; Jing, C.; Kanareykin, A.; Gai, W.; Konecny, R.; Power, J. G.; Kinkead, A. K.

    2010-11-04

    This paper presents a progress report on the development and testing of X-band dielectric-loaded accelerating structures. Recent tests on several quartz DLA structures with different inner diameters are reported. Designs for gap-free DLA structures are presented. Also, planned new experiments are discussed, including higher gradient traveling-wave and standing-wave structures and special grooved structures for multipactor suppression.

  14. The structural response of a rail acceleration

    NASA Technical Reports Server (NTRS)

    Wang, S. Y.

    1984-01-01

    The transient response of a 0.4 by 0.6 cm rectangular bore rail accelerator was analyzed by a three dimensional finite element code. The copper rail deflected to a peak value of 0.08 mm in compression and then oscillated at an amplitude of 0.02 mm. Simultaneously the insulating side wall of glass fabric base, epoxy resin laminate (G-10) was compressed to a peak value of 0.13 mm and rebounded to a steady state in extension. Projectile pinch or blowby due to the rail extension or compression, respectively, can be identified by examining the time history of the rail displacement. The effect of blowby was most significant at the side wall characterized by mm size displacement in compression. Dynamic stress calculations indicate that the G-10 supporting material behind the rail is subjected to over 21 MPa at which the G-10 could fail if the laminate was not carefully oriented. Results for a polycarbonate resin (Lexan) side wall show much larger displacements and stresses than for G-10. The tradeoff between the transparency of Lexan and the mechanical strength of G-10 for sidewall material is obvious. Displacement calculations from the modal method are smaller than the results from the direct integration method by almost an order of magnitude, because the high frequency effect is neglected. Previously announced in STAR as N83-35412

  15. The structural response of a rail acceleration

    NASA Technical Reports Server (NTRS)

    Wang, S. Y.

    1984-01-01

    The transient response of a 0.4 by 0.6 cm rectangular bore rail accelerator was analyzed by a three dimensional finite element code. The copper rail deflected to a peak value of 0.08 mm in compression and then oscillated at an amplitude of 0.02 mm. Simultaneously the insulating side wall of glass fabric base, epoxy resin laminate (G-10) was compressed to a peak value of 0.13 mm and rebounded to a steady state in extension. Projectile pinch or blowby due to the rail extension or compression, respectively, can be identified by examining the time history of the rail displacement. The effect of blowby was most significant at the side wall characterized by mm size displacement in compression. Dynamic stress calculations indicate that the G-10 supporting material behind the rail is subjected to over 21 MPa at which the G-10 could fail if the laminate was not carefully oriented. Results for a polycarbonate resin (Lexan) side wall show much larger displacements and stresses than for G-10. The tradeoff between the transparency of Lexan and the mechanical strength of G-10 for sidewall material is obvious. Displacement calculations from the modal method are smaller than the results from the direct integration method by almost an order of magnitude, because the high frequency effect is neglected. Previously announced in STAR as N83-35412

  16. The structural response of a rail accelerator

    NASA Technical Reports Server (NTRS)

    Wang, S. Y.

    1983-01-01

    The transient response of a 0.4 by 0.6 cm rectangular bore rail accelerator was analyzed by a three dimensional finite element code. The copper rail deflected to a peak value of 0.08 mm in compression and then oscillated at an amplitude of 0.02 mm. Simultaneously the insulating side wall of glass fabric base, epoxy resin laminate (G-1o) was compressed to a peak value of 0.13 mm and rebounded to a steady state in extension. Projectile pinch or blowby due to the rail extension or compression, respectively, can be identified by examining the time history of the rail displacement. The effect of blowby was most significant at the side wall characterized by mm size displacement in compression. Dynamic stress calculations indicate that the G-10 supporting material behind the rail is subjected to over 21 MPa at which the G-10 could fail if the laminate was not carefully oriented. Results for a polycarbonate resin (Lexan) side wall show much larger displacements and stresses than for G-10. The tradeoff between the transparency of Lexan and the mechanical strength of G-10 for sidewall material is obvious. Displacement calculations from the modal method are smaller than the results from the direct integration method by almost an order of magnitude, because the high frequency effect is neglected.

  17. Accelerated probabilistic inference of RNA structure evolution

    PubMed Central

    Holmes, Ian

    2005-01-01

    Background Pairwise stochastic context-free grammars (Pair SCFGs) are powerful tools for evolutionary analysis of RNA, including simultaneous RNA sequence alignment and secondary structure prediction, but the associated algorithms are intensive in both CPU and memory usage. The same problem is faced by other RNA alignment-and-folding algorithms based on Sankoff's 1985 algorithm. It is therefore desirable to constrain such algorithms, by pre-processing the sequences and using this first pass to limit the range of structures and/or alignments that can be considered. Results We demonstrate how flexible classes of constraint can be imposed, greatly reducing the computational costs while maintaining a high quality of structural homology prediction. Any score-attributed context-free grammar (e.g. energy-based scoring schemes, or conditionally normalized Pair SCFGs) is amenable to this treatment. It is now possible to combine independent structural and alignment constraints of unprecedented general flexibility in Pair SCFG alignment algorithms. We outline several applications to the bioinformatics of RNA sequence and structure, including Waterman-Eggert N-best alignments and progressive multiple alignment. We evaluate the performance of the algorithm on test examples from the RFAM database. Conclusion A program, Stemloc, that implements these algorithms for efficient RNA sequence alignment and structure prediction is available under the GNU General Public License. PMID:15790387

  18. Method for computationally efficient design of dielectric laser accelerator structures

    DOE PAGES

    Hughes, Tyler; Veronis, Georgios; Wootton, Kent P.; ...

    2017-06-22

    Here, dielectric microstructures have generated much interest in recent years as a means of accelerating charged particles when powered by solid state lasers. The acceleration gradient (or particle energy gain per unit length) is an important figure of merit. To design structures with high acceleration gradients, we explore the adjoint variable method, a highly efficient technique used to compute the sensitivity of an objective with respect to a large number of parameters. With this formalism, the sensitivity of the acceleration gradient of a dielectric structure with respect to its entire spatial permittivity distribution is calculated by the use of onlymore » two full-field electromagnetic simulations, the original and ‘adjoint’. The adjoint simulation corresponds physically to the reciprocal situation of a point charge moving through the accelerator gap and radiating. Using this formalism, we perform numerical optimizations aimed at maximizing acceleration gradients, which generate fabricable structures of greatly improved performance in comparison to previously examined geometries.« less

  19. rf breakdown tests of mm-wave metallic accelerating structures

    DOE PAGES

    Dal Forno, Massimo; Dolgashev, Valery; Bowden, Gordon; ...

    2016-01-06

    In this study, we explore the physics and frequency-scaling of vacuum rf breakdowns at sub-THz frequencies. We present the experimental results of rf tests performed in metallic mm-wave accelerating structures. These experiments were carried out at the facility for advanced accelerator experimental tests (FACET) at the SLAC National Accelerator Laboratory. The rf fields were excited by the FACET ultrarelativistic electron beam. We compared the performances of metal structures made with copper and stainless steel. The rf frequency of the fundamental accelerating mode, propagating in the structures at the speed of light, varies from 115 to 140 GHz. The traveling wavemore » structures are 0.1 m long and composed of 125 coupled cavities each. We determined the peak electric field and pulse length where the structures were not damaged by rf breakdowns. We calculated the electric and magnetic field correlated with the rf breakdowns using the FACET bunch parameters. The wakefields were calculated by a frequency domain method using periodic eigensolutions. Such a method takes into account wall losses and is applicable to a large variety of geometries. The maximum achieved accelerating gradient is 0.3 GV/m with a peak surface electric field of 1.5 GV/m and a pulse length of about 2.4 ns.« less

  20. rf breakdown tests of mm-wave metallic accelerating structures

    NASA Astrophysics Data System (ADS)

    Dal Forno, Massimo; Dolgashev, Valery; Bowden, Gordon; Clarke, Christine; Hogan, Mark; McCormick, Doug; Novokhatski, Alexander; Spataro, Bruno; Weathersby, Stephen; Tantawi, Sami G.

    2016-01-01

    We are exploring the physics and frequency-scaling of vacuum rf breakdowns at sub-THz frequencies. We present the experimental results of rf tests performed in metallic mm-wave accelerating structures. These experiments were carried out at the facility for advanced accelerator experimental tests (FACET) at the SLAC National Accelerator Laboratory. The rf fields were excited by the FACET ultrarelativistic electron beam. We compared the performances of metal structures made with copper and stainless steel. The rf frequency of the fundamental accelerating mode, propagating in the structures at the speed of light, varies from 115 to 140 GHz. The traveling wave structures are 0.1 m long and composed of 125 coupled cavities each. We determined the peak electric field and pulse length where the structures were not damaged by rf breakdowns. We calculated the electric and magnetic field correlated with the rf breakdowns using the FACET bunch parameters. The wakefields were calculated by a frequency domain method using periodic eigensolutions. Such a method takes into account wall losses and is applicable to a large variety of geometries. The maximum achieved accelerating gradient is 0.3 GV /m with a peak surface electric field of 1.5 GV /m and a pulse length of about 2.4 ns.

  1. Gradient Limitations in Room Temperature and Superconducting Acceleration Structures

    SciTech Connect

    Solyak, N. A.

    2009-01-22

    Accelerating gradient is a key parameter of the accelerating structure in large linac facilities, like future Linear Collider. In room temperature accelerating structures the gradient is limited mostly by breakdown phenomena, caused by high surface electric fields or pulse surface heating. High power processing is a necessary procedure to clean surface and improve the gradient. In the best tested X-band structures the achieved gradient is exceed 100 MV/m in of {approx}200 ns pulses for breakdown rate of {approx}10{sup -7}. Gradient limit depends on number of factors and no one theory which can explain all sets of experimental results and predict gradient in new accelerating structure. In paper we briefly overview the recent experimental results of breakdown studies, progress in understanding of gradient limitations and scaling laws. Although superconducting rf technology has been adopted throughout the world for ILC, it has frequently been difficult to reach the predicted performance in these structures due to a number of factors: multipactoring, field emission, Q-slope, thermal breakdown. In paper we are discussing all these phenomena and the ways to increase accelerating gradient in SC cavity, which are a part of worldwide R and D program.

  2. Gradient limitations in room temperature and superconducting acceleration structures

    SciTech Connect

    Solyak, N.A.; /Fermilab

    2008-10-01

    Accelerating gradient is a key parameter of the accelerating structure in large linac facilities, like future Linear Collider. In room temperature accelerating structures the gradient is limited mostly by breakdown phenomena, caused by high surface electric fields or pulse surface heating. High power processing is a necessary procedure to clean surface and improve the gradient. In the best tested X-band structures the achieved gradient is exceed 100 MV/m in of {approx}200 ns pulses for breakdown rate of {approx} 10{sup -7}. Gradient limit depends on number of factors and no one theory which can explain all sets of experimental results and predict gradient in new accelerating structure. In paper we briefly overview the recent experimental results of breakdown studies, progress in understanding of gradient limitations and scaling laws. Although superconducting rf technology has been adopted throughout the world for ILC, it has frequently been difficult to reach the predicted performance in these structures due to a number of factors: multipactoring, field emission, Q-slope, thermal breakdown. In paper we are discussing all these phenomena and the ways to increase accelerating gradient in SC cavity, which are a part of worldwide R&D program.

  3. Rectangular Dielectric-loaded Structures for Achieving High Acceleration Gradients

    SciTech Connect

    Wang Changbiao; Yakovlev, V. P.; Marshall, T. C.; LaPointe, M. A.; Hirshfield, J. L.

    2006-11-27

    Rectangular dielectric-loaded structures are described that may sustain higher acceleration gradients than conventional all-metal structures with similar apertures. One structure is a test cavity designed to ascertain the breakdown limits of dielectrics, while a second structure could be the basis for a two-beam accelerator. CVD diamond is an attractive dielectric for a high-gradient structure, since the published DC breakdown limit for CVD diamond is {approx} 2 GV/m, although the limit has never been determined for RF fields. Here we present a design of a diamond-lined test cavity to measure the breakdown limit. The designed cavity operates at 34 GHz, where with 10-MW input power it is expected to produce an {approx}800 MV/m field on the diamond surface - provided breakdown is avoided. The two channel rectangular dielectric-loaded waveguide could be a two-beam accelerator structure, in which a drive beam is in one channel and an accelerated beam is in the other. The RF power produced by drive bunches in the drive channel is continuously coupled to the acceleration channel. The ratio of fields in the channels (transformer ratio) for the operating mode can be designed by adjusting the dimensions of the structure. An example of the two-channel structure is described, in which a train of five 3-nC drive bunches excites wake fields in the accelerator channel of up to 1.3 GV/m with a transformer ratio of 10 for the design mode.

  4. Rectangular Dielectric-loaded Structures for Achieving High Acceleration Gradients

    NASA Astrophysics Data System (ADS)

    Wang, Changbiao; Yakovlev, V. P.; Marshall, T. C.; LaPointe, M. A.; Hirshfield, J. L.

    2006-11-01

    Rectangular dielectric-loaded structures are described that may sustain higher acceleration gradients than conventional all-metal structures with similar apertures. One structure is a test cavity designed to ascertain the breakdown limits of dielectrics, while a second structure could be the basis for a two-beam accelerator. CVD diamond is an attractive dielectric for a high-gradient structure, since the published DC breakdown limit for CVD diamond is ˜ 2 GV/m, although the limit has never been determined for RF fields. Here we present a design of a diamond-lined test cavity to measure the breakdown limit. The designed cavity operates at 34 GHz, where with 10-MW input power it is expected to produce an ˜800 MV/m field on the diamond surface—provided breakdown is avoided. The two channel rectangular dielectric-loaded waveguide could be a two-beam accelerator structure, in which a drive beam is in one channel and an accelerated beam is in the other. The RF power produced by drive bunches in the drive channel is continuously coupled to the acceleration channel. The ratio of fields in the channels (transformer ratio) for the operating mode can be designed by adjusting the dimensions of the structure. An example of the two-channel structure is described, in which a train of five 3-nC drive bunches excites wake fields in the accelerator channel of up to 1.3 GV/m with a transformer ratio of 10 for the design mode.

  5. Transverse wake field simulations for the ILC acceleration structure

    SciTech Connect

    Solyak, N.; Lunin, A.; Yakovlev, V.; /Fermilab

    2008-06-01

    Details of wake potential simulation in the acceleration structure of ILC, including the RF cavities and input/HOM couplers are presented. Transverse wake potential dependence is described versus the bunch length. Beam emittance dilution caused by main and HOM couplers is estimated, followed by a discussion of possible structural modifications allowing a reduction of transverse wake potential.

  6. C -band disk-loaded-type accelerating structure for a high acceleration gradient and high-repetition-rate operation

    NASA Astrophysics Data System (ADS)

    Sakurai, T.; Ego, H.; Inagaki, T.; Asaka, T.; Suzuki, D.; Miura, S.; Otake, Y.

    2017-04-01

    A high-acceleration-gradient linear accelerator (LINAC) for an x-ray free electron laser (XFEL) offers the advantages of a short accelerator length and low construction costs. In addition, the high pulse repetition rate of the LINAC, which can drive multiple x-ray beam lines, provides additional user opportunities for experiments involving XFEL. A C -band disk-loaded-type accelerating structure was developed to achieve a high acceleration gradient of >50 MV /m and an rf-pulse repetition rate of 120 pps, which is twice as high as that of the XFEL facility, SACLA (60 pps). The structure has a quasiconstant gradient and a traveling wave type with an accelerating mode of TM 01 -2 π /3 . To reduce the surface electric fields, we employed a cross section with an ellipsoidal curvature around an iris aperture. The accelerating structure was manufactured for SACLA. High-power rf conditioning was conducted to investigate its performance. Owing to the conditioning, the acceleration gradient reached a value of more than 50.1 MV /m . The structure was operated without any serious issues at a repetition rate of 120 pps. The accelerating structures were installed in the dedicated accelerator for EUV-FEL at SACLA beam line-1. Finally, we obtained accelerated electron beams with the structures operated at an acceleration gradient of 41.4 MV /m .

  7. COAXIAL WIRE MEASUREMENTS IN NLC ACCELERATING STRUCTURES

    SciTech Connect

    Jones, Roger M

    2002-06-20

    The coaxial wire method provides an experimental way of measuring wake fields without the need for a particle beam. A special setup has been designed and is in the process of being fabricated at SLAC to measure the loss factors and synchronous frequencies of dipole modes in both traveling and standing wave structures for the Next Linear Collider (NLC). The method is described and predictions based on electromagnetic field simulations are discussed.

  8. Design of High Gradient Accelerating Structure for CLIC

    NASA Astrophysics Data System (ADS)

    Grudiev, A.; Wuensch, W.

    2006-01-01

    A new CLIC main-linac accelerating-structure design, HDS (Hybrid Damped Structure), with improved high-gradient performance, efficiency and simplicity of fabrication is presented. The gains are achieved in part through a new cell design which includes fully-profiled rf surfaces optimized to minimize surface fields, and hybrid damping using both iris slots and radial waveguides. The slotted irises allow a simple structure fabrication in quadrants with no rf currents across joints, a reduced number of pieces per structure (only 4) and a reduced surface requiring precise machining. Further gains are achieved through a new structure optimization procedure, which simultaneously balances surface fields, power flow, short and long-range transverse wakefields and rf-to-beam efficiency. The optimization of a 30 GHz structure with a loaded accelerating gradient of 150 MV/m results in a bunch spacing of eight rf cycles and 31 % rf-to-beam efficiency.

  9. Displacement damage induced in iron by gammas and neutrons under irradiation in the IFMIF test cell

    NASA Astrophysics Data System (ADS)

    Simakov, S. P.; Fischer, U.

    2011-10-01

    This work presents a complete comparative analysis of the radiation damage induced in iron-based materials in IFMIF by photons and neutrons. The gamma induced damage takes into account, for the first time, both photonuclear and photoatomic reaction mechanisms. The relevant cross sections were taken from available data evaluations. The gamma and neutron radiation fields were calculated by the McDeLicious Monte Carlo code using a 3-D geometry model. Finally the gamma and neutron induced damages in the iron have been assessed inside the IFMIF test cell and the surrounding concrete walls. It was found that the photoatomic mechanism dominates the photonuclear with at least one hundred times higher damage rates. The ratio of the gamma and the neutron induced displacement damage was found to be 10 -3 inside the concrete wall and 10 -5 in the components close to d-Li source. This fraction may increase a few times due to the uncertainty of the evaluated γ-dpa cross sections and the different surviving probabilities for defects produced by gammas and neutrons, nevertheless unlikely exceed 1%.

  10. Laser fields in dynamically ionized plasma structures for coherent acceleration

    NASA Astrophysics Data System (ADS)

    Luu-Thanh, Ph.; Tückmantel, T.; Pukhov, A.; Kostyukov, I.

    2015-10-01

    With the emergence of the CAN (Coherent Amplification Network) laser technology, a new scheme for direct particle acceleration in periodic plasma structures has been proposed. By using our full electromagnetic relativistic particle-in-cell (PIC) simulation code equipped with ionisation module, we simulate the laser fields dynamics in the periodic structures of different materials. We study how the dynamic ionization influences the field structure.

  11. Fabrication and cold test of dielectric assist accelerating structure

    NASA Astrophysics Data System (ADS)

    Satoh, D.; Yoshida, M.; Hayashizaki, N.

    2017-09-01

    We present the detailed description of a successful design and cold testing of the dielectric assist accelerating (DAA) structure. The DAA structure consists of ultralow-loss dielectric cylinders and disks with irises which are periodically arranged in a metallic enclosure. The advantage of the DAA structure is that it has an extremely high quality factor and a very high shunt impedance at room temperature since the electromagnetic field distribution of accelerating mode can be controlled by dielectric parts so that the wall loss on the metallic surface is greatly reduced. A prototype of the five-cell DAA structure was designed and built at C-band (5.712 GHz), and cold tested. Three types of dielectric cell structure, "regular," "end," and "hybrid" dielectric cells, are fabricated by sintering high-purity magnesia. The prototype was assembled by stacking these cells in the hollow copper cylinder, whose two ends are closed by copper plates. The resonant frequency of the prototype was tuned to the desired frequency by machining only end copper plates. The unloaded quality factor of the accelerating mode was measured at 119,314 and the shunt impedance per unit length of the prototype was estimated from the experimental results of the bead pull measurement as Zsh=617 M Ω /m , which were within 2 percent of the design values. The field distribution of accelerating mode was also measured by the bead pull method, and its results agreed well with simulation results.

  12. Two-beam, Multi-mode Detuned Accelerating Structure

    SciTech Connect

    Kazakov, S. Yu.; Kuzikov, S. V.; Yakovlev, V. P.; Hirshfield, J. L.

    2009-01-22

    A two-beam accelerator structure is described having several novel features including all metal construction, no transfer structures required between the drive and accelerator channels, symmetric fields at the axes of each channel, RF micropulse widths on cavity irises that are less than half those for a conventional cavity at the same fundamental frequency by virtue of using several harmonically-related cavity modes, and a transformer ratio much greater than unity by the use of detuned cavities. Detuning is also shown to allow either parallel or anti-parallel directions for the drive and accelerated beams. A preliminary calculation for the dilution of emittance due to short-range wakes for drive beam parameters similar to those for CLIC shows this effect to be acceptably small.

  13. High Gradient Accelerating Structures for Carbon Therapy Linac

    SciTech Connect

    Kutsaev, Sergey; Agustsson, R.; Faillace, L.; Goel, A.; Mustapha, B.; Nassiri, A.; Ostroumov, P.; Plastun, A.; Savin, E.

    2016-05-01

    Carbon therapy is the most promising among techniques for cancer treatment, as it has demonstrated significant improvements in clinical efficiency and reduced toxicity profiles in multiple types of cancer through much better localization of dose to the tumor volume. RadiaBeam, in collaboration with Argonne National Laboratory, are developing an ultra-high gradient linear accelerator, Advanced Compact Carbon Ion Linac (ACCIL), for the delivery of ion-beams with end-energies up to 450 MeV/u for 12C6+ ions and 250 MeV for protons. In this paper, we present a thorough comparison of standing and travelling wave designs for high gradient S-Band accelerating structures operating with ions at varying velocities, relative to the speed of light, in the range 0.3-0.7. In this paper we will compare these types of accelerating structures in terms of RF, beam dynamics and thermo-mechanical performance.

  14. X-band dielectric loaded traveling-wave acceleration structure

    NASA Astrophysics Data System (ADS)

    Zou, P.; Gai, W.; Konecny, R.; Sun, X.; Wong, T.

    2001-05-01

    We report on the construction, numerical modeling and experimental testing of a traveling-wave acceleration structure based on a dielectric-lined circular waveguide. This type of structure has similar acceleration properties to disk-loaded metal slow wave structures but with some distinct advantages in terms of simplicity of fabrication, suppression of parasitic wakefield effects, and having no dark current. Efficient coupling of external RF power to the cylindrical dielectric waveguide is a technical challenge, particularly to structures loaded with very high dielectric constant materials. We have designed and constructed an 11.4 GHz structure loaded with ceramic with dielectric constant of 20, to be powered by an external RF power source. High efficiency RF coupling has been achieved using a combination of a tapered dielectric end section and a carefully adjusted coupling slot. Bench tests using a network analyzer have demonstrated a power coupling efficiency in excess of 95% with bandwidth of 30 MHz, and vacuum tests have also shown that this dielectric loaded structure can be operated in an ultra-high vacuum environment. Thus, this work provides a necessary basis for construction of an accelerator using this kind of structure. We have also simulated the parameters of this structure using MAFIA. Within the limits of the approximations used, the results are in agreement with the bench measurements.

  15. Dielectric-Lined High-Gradient Accelerator Structure

    SciTech Connect

    Jay L. Hirshfield

    2012-04-24

    Rectangular particle accelerator structures with internal planar dielectric elements have been studied, with a view towards devising structures with lower surface fields for a given accelerating field, as compared with structures without dielectrics. Success with this concept is expected to allow operation at higher accelerating gradients than otherwise on account of reduced breakdown probabilities. The project involves studies of RF breakdown on amorphous dielectrics in test cavities that could enable high-gradient structures to be built for a future multi-TeV collider. The aim is to determine what the limits are for RF fields at the surfaces of selected dielectrics, and the resulting acceleration gradient that could be achieved in a working structure. The dielectric of principal interest in this study is artificial CVD diamond, on account of its advertised high breakdown field ({approx}2 GV/m for dc), low loss tangent, and high thermal conductivity. Experimental studies at mm-wavelengths on materials and structures for achieving high acceleration gradient were based on the availability of the 34.3 GHz third-harmonic magnicon amplifier developed by Omega-P, and installed at the Yale University Beam Physics Laboratory. Peak power from the magnicon was measured to be about 20 MW in 0.5 {micro}s pulses, with a gain of 54 dB. Experiments for studying RF high-field effects on CVD diamond samples failed to show any evidence after more than 10{sup 5} RF pulses of RF breakdown up to a tangential surface field strength of 153 MV/m; studies at higher fields were not possible due to a degradation in magnicon performance. A rebuild of the tube is underway at this writing. Computed performance for a dielectric-loaded rectangular accelerator structure (DLA) shows highly competitive properties, as compared with an existing all-metal structure. For example, comparisons were made of a DLA structure having two planar CVD diamond elements with a all-metal CERN structure HDS

  16. Acceleration of stable interface structure searching using a kriging approach

    NASA Astrophysics Data System (ADS)

    Kiyohara, Shin; Oda, Hiromi; Tsuda, Koji; Mizoguchi, Teruyasu

    2016-04-01

    Crystalline interfaces have a tremendous impact on the properties of materials. Determination of the atomic structure of the interface is crucial for a comprehensive understanding of the interface properties. Despite this importance, extensive calculation is necessary to determine even one interface structure. In this study, we apply a technique called kriging, borrowed from geostatistics, to accelerate the determination of the interface structure. The atomic structure of simplified coincidence-site lattice interfaces were determined using the kriging approach. Our approach successfully determined the most stable interface structure with an efficiency almost 2 orders of magnitude better than the traditional “brute force” approach.

  17. Progress on Diamond-Based Cylindrical Dielectric Accelerating Structures

    SciTech Connect

    Kanareykin, A.; Schoessow, P.; Conde, M.; Gai, W.

    2006-11-27

    The development of a high gradient diamond-based cylindrical dielectric loaded accelerator (DLA) is presented. A diamond-loaded DLA can potentially sustain accelerating gradients far in excess of the limits experimentally observed for conventional metallic accelerating structures. The electrical and mechanical properties of diamond make it an ideal candidate material for use in dielectric accelerators: high rf breakdown level, extremely low dielectric losses and the highest available thermoconductive coefficient. We used the hot-filament Chemical Vapor Deposition (CVD) process to produce high quality 5-10 cm long cylindrical diamond layers. Our collaboration has also been developing a new method of CVD diamond surface preparation that reduces the secondary electron emission coefficient below unity. Special attention was paid to the numerical optimization of the waveguide to structure rf coupling section, where the surface magnetic and electric fields were minimized relative to the accelerating gradient and within known metal surface breakdown limits. We conclude with a brief overview of the use of diamond microstructures for use in compact rf sources.

  18. Progress on Diamond-Based Cylindrical Dielectric Accelerating Structures

    NASA Astrophysics Data System (ADS)

    Kanareykin, A.; Schoessow, P.; Conde, M.; Gai, W.

    2006-11-01

    The development of a high gradient diamond-based cylindrical dielectric loaded accelerator (DLA) is presented. A diamond-loaded DLA can potentially sustain accelerating gradients far in excess of the limits experimentally observed for conventional metallic accelerating structures. The electrical and mechanical properties of diamond make it an ideal candidate material for use in dielectric accelerators: high rf breakdown level, extremely low dielectric losses and the highest available thermoconductive coefficient. We used the hot-filament Chemical Vapor Deposition (CVD) process to produce high quality 5-10 cm long cylindrical diamond layers. Our collaboration has also been developing a new method of CVD diamond surface preparation that reduces the secondary electron emission coefficient below unity. Special attention was paid to the numerical optimization of the waveguide to structure rf coupling section, where the surface magnetic and electric fields were minimized relative to the accelerating gradient and within known metal surface breakdown limits. We conclude with a brief overview of the use of diamond microstructures for use in compact rf sources.

  19. The Organizational Culture and Structure of Accelerated Schools.

    ERIC Educational Resources Information Center

    Steaffens, Susan; McCarthy, Jane; Putney, LeAnn; Steinhoff, Carl

    This paper describes the organizational culture and structure of five accelerated schools in the Clark County School District in Nevada, focusing on the similarities and differences among these schools. The cultural aspects of the schools under comparison included the guiding principles, the central values, and the learning philosophy, whereas the…

  20. Two-Channel Rectangular Dielectric Wake Field Accelerator Structure Experiment

    SciTech Connect

    Sotnikov, G. V.; Marshall, T. C.; Shchelkunov, S. V.; Didenko, A.; Hirshfield, J. L.

    2009-01-22

    A design is presented for a two-channel 30-GHz rectangular dielectric wake field accelerator structure being built for experimental tests at Argonne National Laboratory (ANL). This structure allows for a transformer ratio T much greater than two, and permits continuous coupling of energy from drive bunches to accelerated bunches. It consists of three planar slabs of cordierite ceramic ({epsilon} = 4.7) supported within a rectangular copper block, forming a drive channel 12 mmx6 mm, and an accelerator channel 2 mmx6 mm. When driven by a 50 nC, 14 MeV single bunch available at ANL, theory predicts an acceleration field of 6 MeV/m, and T = 12.6. Inherent transverse wake forces introduce deflections and some distortion of bunch profiles during transit through the structure that are estimated to be tolerable. Additionally, a cylindrical two-channel DWFA is introduced which shares many advantages of the rectangular structure including high T, and the added virtue of axisymmetry that eliminates lowest-order transverse deflecting forces.

  1. Structure of Accelerated Learning Program (ALP) Efforts, 2000-01.

    ERIC Educational Resources Information Center

    Baenen, Nancy; Yaman, Kimberly

    This report focuses on the structure of instructional assistance available through the Accelerated Learning Program (ALP) to students who show low achievement in the Wake County Public School System (WCPSS), North Carolina. Context information is also provided on other programs available to these students. Reports on ALP student participation,…

  2. Two-Channel Rectangular Dielectric Wake Field Accelerator Structure Experiment

    NASA Astrophysics Data System (ADS)

    Sotnikov, G. V.; Marshall, T. C.; Shchelkunov, S. V.; Didenko, A.; Hirshfield, J. L.

    2009-01-01

    A design is presented for a two-channel 30-GHz rectangular dielectric wake field accelerator structure being built for experimental tests at Argonne National Laboratory (ANL). This structure allows for a transformer ratio T much greater than two, and permits continuous coupling of energy from drive bunches to accelerated bunches. It consists of three planar slabs of cordierite ceramic (ɛ = 4.7) supported within a rectangular copper block, forming a drive channel 12 mm×6 mm, and an accelerator channel 2 mm×6 mm. When driven by a 50 nC, 14 MeV single bunch available at ANL, theory predicts an acceleration field of 6 MeV/m, and T = 12.6. Inherent transverse wake forces introduce deflections and some distortion of bunch profiles during transit through the structure that are estimated to be tolerable. Additionally, a cylindrical two-channel DWFA is introduced which shares many advantages of the rectangular structure including high T, and the added virtue of axisymmetry that eliminates lowest-order transverse deflecting forces.

  3. Some technological features for fabrication of accelerating structures

    NASA Astrophysics Data System (ADS)

    Avagyan, V. Sh.; Danielyan, V. A.; Dekhtiarov, V. S.; Mkrtchyan, T. H.; Nagdalyan, S. A.; Simonyan, A. S.; Grigoryan, B. A.; Tsakanian, A. V.; Vardanyan, A. A.; Vardanyan, V. V.

    2017-07-01

    The distribution and control of temperature analyses during the brazing of lengthy accelerating structures, by induction heating usage, have been carried out. The problem of individual elements positioning, relative to each other during brazing, is solved. The results of metallographic studies for brazing zones are shown.

  4. RF ACCELERATING STRUCTURE FOR THE MUON COOLING EXPERIMENT.

    SciTech Connect

    CORLETT,J.; GREEN,M.; LI,D.; HOLTKAMP,N.; MORETTI,A.; KIRK,H.G.; PALMER,R.B.; ZHAO,Y.; SUMMERS,D.

    1999-03-29

    The ionization cooling of muons requires longitudinal acceleration of the muons after scattering in a hydrogen target. In order to maximize the accelerating voltage, we propose using linear accelerating structures with cells bounded by thin beryllium metal foils. This produces an on-axis field equivalent to the maximum surface field, whereas with beam-pipes the accelerating field is approximately half that of the peak surface field in the cavity. The muons interact only weakly with the thin foils. A {pi}/2 interleaved cavity structure has been chosen, with alternate cells coupled together externally, and the two groups of cells fed in quadrature. At present they are considering an operating temperature of 77K to gain a factor of at least two in Q-value over room temperature. The authors describe the design of the {pi}/2 interleaved cavity structure, design of an alternative {pi}-mode open structure, preliminary experimental results from a low-power test cavity, and plans for high-power testing.

  5. Improved input and output couplers for SC acceleration structure

    SciTech Connect

    Solyak, N.; Gonin, I.; Latina, A.; Lunin, A.; Poloubotko, V.; Yakovlev, V.; /Fermilab

    2009-04-01

    Different couplers are described that allow the reduction of both transverse wake potential and RF kick in the SC acceleration structure of ILC. A simple rotation of the couplers reducing the RF kick and transverse wake kick is discussed for both the main linac and bunch compressors, along with possible limitations of this method. Designs of a coupler unit are presented which preserve axial symmetry of the structure, and provide reduced both the RF kick and transverse wake field.

  6. Ion Bombardment of Microprotrusions in High Gradient Accelerating Structures

    SciTech Connect

    Nusinovich, Gregory S.; Kashyn, Dmytro; Antonsen, Thomas Jr.; Haber, Irving

    2010-11-04

    This paper starts from a brief overview of theoretical studies of high-gradient accelerating structures at the University of Maryland. The rest of the paper is devoted to the analysis of ion bombardment of small protrusions in such structures. First, this problem is studied analytically. Then, some results of particle-in-cell simulations performed with the use of code WARP are presented and discussed.

  7. Calculation of structural dynamic forces and stresses using mode acceleration

    NASA Technical Reports Server (NTRS)

    Blelloch, Paul

    1989-01-01

    While the standard mode acceleration formulation in structural dynamics has often been interpreted to suggest that the reason for improved convergence obtainable is that the dynamic correction factor is divided by the modal frequencies-squared, an alternative formulation is presented which clearly indicates that the only difference between mode acceleration and mode displacement data recovery is the addition of a static correction term. Attention is given to the advantages in numerical implementation associated with this alternative, as well as to an illustrative example.

  8. Woodpile Structure Fabrication for Photonic Crystal Laser Acceleration

    SciTech Connect

    McGuinness, C.; Colby, E.; England, R. J.; Noble, R. J.; Sears, C. M.; Siemann, R.; Spencer, J.; Waltz, D.; Byer, R. L.; Plettner, T.; Cowan, B. M.

    2009-01-22

    We describe initial steps at fabricating a dielectric photonic bandgap accelerator structure designed to operate at near IR frequencies. Such a structure operating at these frequencies requires extremely small, sub-micron sized features, forcing one to use lithographic means for fabrication. A process based upon lithographic equipment at the Stanford Nanofabrication Facility has been developed and a four layer test structure has been fabricated. Unexpected problems with the final etch step, and corresponding modifications to the process flow addressing these problems, are described. Spectroscopic measurements of the structure have been taken and are compared to simulations.

  9. Woodpile Structure Fabrication for Photonic Crystal Laser Acceleration

    SciTech Connect

    McGuinness, C.; Byer, R.L.; Colby, E.; Cowan, B.M.; England, R.J.; Noble, R.J.; Plettner, T.; Sears, C.M.; Siemann, R.; Spencer, J.; Waltz, D.; /SLAC

    2010-06-30

    We describe initial steps at fabricating a dielectric photonic bandgap accelerator structure designed to operate at near IR frequencies. Such a structure operating at these frequencies requires extremely small, sub-micron sized features, forcing one to use lithographic means for fabrication. A process based upon lithographic equipment at the Stanford Nanofabrication Facility has been developed and a four layer test structure has been fabricated. Unexpected problems with the final etch step, and corresponding modifications to the process flow addressing these problems, are described. Spectroscopic measurements of the structure have been taken and are compared to simulations.

  10. Electromagnetic Structure and Electron Acceleration in Shock–Shock Interaction

    NASA Astrophysics Data System (ADS)

    Nakanotani, Masaru; Matsukiyo, Shuichi; Hada, Tohru; Mazelle, Christian X.

    2017-09-01

    A shock–shock interaction is investigated by using a one-dimensional full particle-in-cell simulation. The simulation reproduces the collision of two symmetrical high Mach number quasi-perpendicular shocks. The basic structure of the shocks and ion dynamics is similar to that obtained by previous hybrid simulations. The new aspects obtained here are as follows. Electrons are already strongly accelerated before the two shocks collide through multiple reflection. The reflected electrons self-generate waves upstream between the two shocks before they collide. The waves far upstream are generated through the right-hand resonant instability with the anomalous Doppler effect. The waves generated near the shock are due to firehose instability and have much larger amplitudes than those due to the resonant instability. The high-energy electrons are efficiently scattered by the waves so that some of them gain large pitch angles. Those electrons can be easily reflected at the shock of the other side. The accelerated electrons form a power-law energy spectrum. Due to the accelerated electrons, the pressure of upstream electrons increases with time. This appears to cause the deceleration of the approaching shock speed. The accelerated electrons having sufficiently large Larmor radii are further accelerated through the similar mechanism working for ions when the two shocks are colliding.

  11. Coherent acceleration by laser pulse echelons in periodic plasma structures

    NASA Astrophysics Data System (ADS)

    Pukhov, A.; Kostyukov, I.; Tückmantel, T.; Luu-Thanh, Ph.; Mourou, G.

    2014-05-01

    We consider a possibilty to use an echelon of mutually coherent laser pulses generated by the emerging CAN (Coherent Amplification Network) technology for direct particle acceleration in periodic plasma structures. We discuss resonant and free streaming configurations. The resonant plasma structures can trap energy of longer laser pulses but are limited to moderate laser intensities of about 1014 W/cm2 and are very sensitive to the structure quality. The free streaming configurations can survive laser intensities above 1018 W/cm2 for several tens of femtoseconds so that sustained accelerating rates well above TeV/m are feasible. In our full electromagnetic relativistic particle-in-cell (PIC) simulations we show a test electron bunch gaining up to 200 GeV over a distance of 10.2 cm only.

  12. On radiative acceleration in spine-sheath structured blazar jets

    NASA Astrophysics Data System (ADS)

    Chhotray, A.; Nappo, F.; Ghisellini, G.; Salafia, O. S.; Tavecchio, F.; Lazzati, D.

    2017-04-01

    It has been proposed that blazar jets are structured, with a fast spine surrounded by a slower sheath or layer. This structured jet model explains some properties of their emission and morphology. Because of their relative motion, the radiation produced by one component is seen amplified by the other, thus enhancing the inverse Compton emission of both. Radiation is emitted anisotropically in the comoving frames and causes the emitting plasma to recoil. As seen in the observer frame, this corresponds to a deceleration of the fastest component (the spine) and an acceleration of the slower one (the layer). While the deceleration of the spine has already been investigated, here we study for the first time the acceleration of the sheath and find self-consistent velocity profile solutions for both the spine and the sheath while accounting for radiative cooling. We find that the sheath can be accelerated to the velocities required by the observations if its leptons remain energetic in the acceleration region, assumed to be of the order of ˜100 Schwarzschild radii, demanding continuous injection of energetic particles in that region.

  13. Development of X-band accelerating structures for high gradients

    NASA Astrophysics Data System (ADS)

    Bini, S.; Chimenti, V.; Marcelli, A.; Palumbo, L.; Spataro, B.; A. Dolgashev, V.; Tantawi, S.; D. Yeremian, A.; Higashi, Y.; G. Grimaldi, M.; Romano, L.; Ruffino, F.; Parodi, R.

    2012-07-01

    Short copper standing wave (SW) structures operating at an X-band frequency have been recently designed and manufactured at the Laboratori Nazionali di Frascati of the Istituto Nazionale di Fisica Nucleare (INFN) using the vacuum brazing technique. High power tests of the structures have been performed at the SLAC National Accelerator Laboratory. In this manuscript we report the results of these tests and the activity in progress to enhance the high gradient performance of the next generation of structures, particularly the technological characterization of high performance coatings obtained via molybdenum sputtering.

  14. Sulfated Glycosaminoglycans Accelerate Transthyretin Amyloidogenesis by Quaternary Structural Conversion†

    PubMed Central

    Bourgault, Steve; Solomon, James P.; Reixach, Natàlia; Kelly, Jeffery W.

    2011-01-01

    Glycosaminoglycans (GAGs), which are found in association with all extracellular amyloid deposits in humans, are known to accelerate the aggregation of various amyloidogenic proteins in vitro. However, the precise molecular mechanism(s) by which GAGs accelerate amyloidogenesis remains elusive. Herein, we show that sulfated GAGs, especially heparin, accelerate transthyretin (TTR) amyloidogenesis by quaternary structural conversion. The clustering of sulfate groups on heparin and its polymeric nature are essential features for accelerating TTR amyloidogenesis. Heparin does not influence TTR tetramer stability or TTR dissociation kinetics, nor does it alter the folded monomer – misfolded monomer equilibrium directly. Instead, heparin accelerates the conversion of preformed TTR oligomers into larger aggregates. The more rapid disappearance of monomeric TTR in the presence of heparin likely reflects the fact that the monomer–misfolded amyloidogenic monomer–oligomer–TTR fibril equilibria are all linked—a hypothesis that is strongly supported by the light scattering data. TTR aggregates prepared in presence of heparin showed a higher resistance to trypsin and proteinase K proteolysis and a lower exposure of hydrophobic side chains comprising hydrophobic clusters, suggesting an active role in amyloidogenesis. Our data suggest that heparin accelerates TTR aggregation by a scaffold-based mechanism, in which the sulfate groups comprising GAGs interact primarily with TTR oligomers through electrostatic interactions, concentrating and orienting the oligomers, facilitating the formation of higher molecular weight aggregates. This model raises the possibility that GAGs may play a protective role in human amyloid diseases by interacting with proteotoxic oligomers and promoting their association into less toxic amyloid fibrils. PMID:21194234

  15. Present status of the liquid lithium target facility in the international fusion materials irradiation facility (IFMIF)

    NASA Astrophysics Data System (ADS)

    Nakamura, Hiroo; Riccardi, B.; Loginov, N.; Ara, K.; Burgazzi, L.; Cevolani, S.; Dell'Orco, G.; Fazio, C.; Giusti, D.; Horiike, H.; Ida, M.; Ise, H.; Kakui, H.; Matsui, H.; Micciche, G.; Muroga, T.; Nakamura, Hideo; Shimizu, K.; Sugimoto, M.; Suzuki, A.; Takeuchi, H.; Tanaka, S.; Yoneoka, T.

    2004-08-01

    During the three year key element technology phase of the International Fusion Materials Irradiation Facility (IFMIF) project, completed at the end of 2002, key technologies have been validated. In this paper, these results are summarized. A water jet experiment simulating Li flow validated stable flow up to 20 m/s with a double reducer nozzle. In addition, a small Li loop experiment validated stable Li flow up to 14 m/s. To control the nitrogen content in Li below 10 wppm will require surface area of a V-Ti alloy getter of 135 m 2. Conceptual designs of diagnostics have been carried out. Moreover, the concept of a remote handling system to replace the back wall based on `cut and reweld' and `bayonet' options has been established. Analysis by FMEA showed safe operation of the target system. Recent activities in the transition phase, started in 2003, and plan for the next phase are also described.

  16. Research and Development for Ultra-High Gradient Accelerator Structures

    SciTech Connect

    Tantawi, Sami G.; Dolgashev, Valery; Higashi, Yasuo; Spataro, Bruno

    2010-11-04

    Research on the basic physics of high-gradient, high frequency accelerator structures and the associated RF/microwave technology are essential for the future of discovery science, medicine and biology, energy and environment, and national security. We will review the state-of-the-art for the development of high gradient linear accelerators. We will present the research activities aimed at exploring the basic physics phenomenon of RF breakdown. We present the experimental results of a true systematic study in which the surface processing, geometry, and materials of the structures have been varied, one parameter at a time. The breakdown rate or alternatively, the probability of breakdown/pulse/meter has been recorded for different operating parameters. These statistical data reveal a strong dependence of breakdown probability on surface magnetic field, or alternatively on surface pulsed heating. This is in contrast to the classical view of electric field dependence.

  17. Research and Development for Ultra-High Gradient Accelerator Structures

    SciTech Connect

    Tantawi, Sami G.; Dolgashev, Valery; Higashi, Yasuo; Spataro, Bruno; /Frascati

    2012-06-11

    Research on the basic physics of high-gradient, high frequency accelerator structures and the associated RF-microwave technology are essential for the future of discovery science, medicine and biology, energy and environment, and national security. We will review the state-of-the-art for the development of high gradient linear accelerators. We will present the research activities aimed at exploring the basic physics phenomenon of RF breakdown. We present the experimental results of a true systematic study in which the surface processing, geometry, and materials of the structures have been varied, one parameter at a time. The breakdown rate or alternatively, the probability of breakdown-pulse-meter has been recorded for different operating parameters. These statistical data reveal a strong dependence of breakdown probability on surface magnetic field, or alternatively on surface pulsed heating. This is in contrast to the classical view of electric field dependence.

  18. Enhanced Ion Acceleration from Micro-tube Structured Targets

    NASA Astrophysics Data System (ADS)

    Snyder, Joseph; Ji, Liangliang; Akli, Kramer

    2015-11-01

    We present an enhanced ion acceleration method that leverages recent advancements in 3D printing for target fabrication. Using the three-dimensional Particle-in-Cell simulation code Virtual Laser-Plasma Lab (VLPL), we model the interaction of a short pulse, high intensity laser with a micro-tube plasma (MTP) structured target. When compared to flat foils, the MTP target enhances the maximum proton energy by a factor of about 4. The ion enhancement is attributed to two main factors: high energy electrons extracted from the tube structure enhancing the accelerating field and light intensification within the MTP target increasing the laser intensity at the location of the foil. We also present results on ion energy scaling with micro-tube diameter and incident laser pulse intensity. This work was supported by the AFOSR under contract No. FA9550-14-1-0085.

  19. Research and Development for Ultra-High Gradient Accelerator Structures

    NASA Astrophysics Data System (ADS)

    Tantawi, Sami G.; Dolgashev, Valery; Higashi, Yasuo; Spataro, Bruno

    2010-11-01

    Research on the basic physics of high-gradient, high frequency accelerator structures and the associated RF/microwave technology are essential for the future of discovery science, medicine and biology, energy and environment, and national security. We will review the state-of-the-art for the development of high gradient linear accelerators. We will present the research activities aimed at exploring the basic physics phenomenon of RF breakdown. We present the experimental results of a true systematic study in which the surface processing, geometry, and materials of the structures have been varied, one parameter at a time. The breakdown rate or alternatively, the probability of breakdown/pulse/meter has been recorded for different operating parameters. These statistical data reveal a strong dependence of breakdown probability on surface magnetic field, or alternatively on surface pulsed heating. This is in contrast to the classical view of electric field dependence.

  20. Summary report of working group 3: Laser and high-gradient structure-based acceleration

    NASA Astrophysics Data System (ADS)

    Andonian, Gerard; Simakov, Evgenya

    2017-03-01

    High-gradient particle acceleration with reduced power demands is essential for miniaturization and cost reduction of future accelerators. Applications for compact accelerators span collider research for High Energy Physics, light source development for Basic Energy Sciences and National Security, and industrial accelerators for Energy and Environmental Applications. Working Group 3 discussed and surveyed the recent advances in achieving higher gradients and better acceleration efficiency in externally powered, structure-based accelerators. The topics covered in Working Group 3 included dielectric laser acceleration, millimeter-wave accelerators, breakdown phenomena, exotic topologies such as photonic band-gap structures, artificial materials, and nanostructures, and novel rf technology.

  1. Accelerating VASP electronic structure calculations using graphic processing units.

    PubMed

    Hacene, Mohamed; Anciaux-Sedrakian, Ani; Rozanska, Xavier; Klahr, Diego; Guignon, Thomas; Fleurat-Lessard, Paul

    2012-12-15

    We present a way to improve the performance of the electronic structure Vienna Ab initio Simulation Package (VASP) program. We show that high-performance computers equipped with graphics processing units (GPUs) as accelerators may reduce drastically the computation time when offloading these sections to the graphic chips. The procedure consists of (i) profiling the performance of the code to isolate the time-consuming parts, (ii) rewriting these so that the algorithms become better-suited for the chosen graphic accelerator, and (iii) optimizing memory traffic between the host computer and the GPU accelerator. We chose to accelerate VASP with NVIDIA GPU using CUDA. We compare the GPU and original versions of VASP by evaluating the Davidson and RMM-DIIS algorithms on chemical systems of up to 1100 atoms. In these tests, the total time is reduced by a factor between 3 and 8 when running on n (CPU core + GPU) compared to n CPU cores only, without any accuracy loss. Copyright © 2012 Wiley Periodicals, Inc.

  2. High-performance insulator structures for accelerator applications

    SciTech Connect

    Sampayan, S.E.; Caporaso, G.J.; Sanders, D.M.; Stoddard, R.D.; Trimble, D.O.; Elizondo, J.; Krogh, M.L.; Wieskamp, T.F.

    1997-05-01

    A new, high gradient insulator technology has been developed for accelerator systems. The concept involves the use of alternating layers of conductors and insulators with periods of order 1 mm or less. These structures perform many times better (about 1.5 to 4 times higher breakdown electric field) than conventional insulators in long pulse, short pulse, and alternating polarity applications. We describe our ongoing studies investigating the degradation of the breakdown electric field resulting from alternate fabrication techniques, the effect of gas pressure, the effect of the insulator-to-electrode interface gap spacing, and the performance of the insulator structure under bi-polar stress.

  3. On the resonant behavior of laminated accelerating structures

    NASA Astrophysics Data System (ADS)

    Ivanyan, M. I.; Avagyan, V. Sh.; Danielyan, V. A.; Tsakanian, A. V.; Vardanyan, A. S.; Zakaryan, V. S.

    2017-03-01

    The laminated round metallic waveguide is one of the promising options for high frequency single-mode accelerating structures. Under certain conditions the longitudinal impedance of such type structures has a narrow-band resonance that corresponds to slowly propagating synchronous TM01 fundamental mode. In this paper the resonant properties of two parallel plates and rectangular cavity with laminated walls are studied. The first measurement results performed for the copper cavity of rectangular cross section with inner germanium layers at top and bottom walls are presented. The measurements show the existence of a dedicated resonant frequency being in a good agreement with the one predicted for the corresponding laminated parallel plates.

  4. Micro structure processing on plastics by accelerated hydrogen molecular ions

    NASA Astrophysics Data System (ADS)

    Hayashi, H.; Hayakawa, S.; Nishikawa, H.

    2017-08-01

    A proton has 1836 times the mass of an electron and is the lightest nucleus to be used for accelerator in material modification. We can setup accelerator with the lowest acceleration voltage. It is preferable characteristics of Proton Beam Writer (PBW) for industrial applications. On the contrary ;proton; has the lowest charge among all nuclei and the potential impact to material is lowest. The object of this research is to improve productivity of the PBW for industry application focusing on hydrogen molecular ions. These ions are generated in the same ion source by ionizing hydrogen molecule. There is no specific ion source requested and it is suitable for industrial use. We demonstrated three dimensional (3D) multilevel micro structures on polyester base FPC (Flexible Printed Circuits) using proton, H2+ and H3+. The reactivity of hydrogen molecular ions is much higher than that of proton and coincident with the level of expectation. We can apply this result to make micro devices of 3D multilevel structures on FPC.

  5. Dark Current Simulation for Linear Collider Accelerator Structures

    SciTech Connect

    Ng, C.K.; Li, Z.; Zhan, X.; Srinivas, V.; Wang, J.; Ko, K.; /SLAC

    2011-08-25

    The dynamics of field-emitted electrons in the traveling wave fields of a constant gradient (tapered) disk-loaded waveguide is followed numerically. Previous simulations have been limited to constant impedance (uniform) structures for sake of simplicity since only the fields in a unit cell is needed. Using a finite element field solver on a parallel computer, the fields in the tapered structure can now be readily generated. We will obtain the characteristics of the dark current emitted from both structure types and compare the two results with and without the effect of secondary electrons. The NLC and JLC detuned structures are considered to study if dark current may pose a problem for high gradient acceleration in the next generation of Linear Colliders.

  6. Design of Accelerator Online Simulator Server Using Structured Data

    SciTech Connect

    Shen, Guobao; Chu, Chungming; Wu, Juhao; Kraimer, Martin; /Argonne

    2012-07-06

    Model based control plays an important role for a modern accelerator during beam commissioning, beam study, and even daily operation. With a realistic model, beam behaviour can be predicted and therefore effectively controlled. The approach used by most current high level application environments is to use a built-in simulation engine and feed a realistic model into that simulation engine. Instead of this traditional monolithic structure, a new approach using a client-server architecture is under development. An on-line simulator server is accessed via network accessible structured data. With this approach, a user can easily access multiple simulation codes. This paper describes the design, implementation, and current status of PVData, which defines the structured data, and PVAccess, which provides network access to the structured data.

  7. On the relationship between collisionless shock structure and energetic particle acceleration

    NASA Technical Reports Server (NTRS)

    Kennel, C. F.

    1983-01-01

    Recent experimental research on bow shock structure and theoretical studies of quasi-parallel shock structure and shock acceleration of energetic particles were reviewed, to point out the relationship between structure and particle acceleration. The phenomenological distinction between quasi-parallel and quasi-perpendicular shocks that has emerged from bow shock research; present efforts to extend this work to interplanetary shocks; theories of particle acceleration by shocks; and particle acceleration to shock structures using multiple fluid models were discussed.

  8. Fabrication of x-band accelerating structures at Fermilab

    SciTech Connect

    Tug T Arkan et al.

    2004-07-20

    The RF Technology Development group at Fermilab is working together with the NLC and GLC groups at SLAC and KEK on developing technology for room temperature X-band accelerating structures for a future linear collider. We built six 60-cm long, high phase advance, detuned structures (HDS or FXB series). These structures have 150 degrees phase advance per cell, and are intended for high gradient tests. The structures were brazed in a vacuum furnace with a partial pressure of argon, rather than in a hydrogen atmosphere. We have also begun to build 60-cm long, damped and detuned structures (HDDS or FXC/FXD series). We have built 5 FXC and 1 FXD structures. Our goal was to build six structures for the 8-pack test at SLAC by the end of March 2004, as part of the GLC/NLC effort to demonstrate the readiness of room temperature RF technology for a linear collider. This paper describes the RF structure factory infrastructure (clean rooms, vacuum furnaces, vacuum equipment, RF equipment etc.), and the fabrication techniques utilized (the machining of copper cells/couplers, quality control, etching, vacuum brazing, cleanliness requirements etc.) for the production of FXB and FXC/FXD structures.

  9. Summary report of working group 3: High gradient and laser-structure based acceleration

    SciTech Connect

    Solyak, N.; Cowan, B.M.; /Tech-X, Boulder

    2010-01-01

    The charge for the working group on high gradient and laser-structure based acceleration was to assess the current challenges involved in developing an advanced accelerator based on electromagnetic structures, and survey state-of-the-art methods to address those challenges. The topics of more than 50 presentations in the working group covered a very broad range of issues, from ideas, theoretical models and simulations, to design and manufacturing of accelerating structures and, finally, experimental results on obtaining extremely high accelerating gradients in structures from conventional microwave frequency range up to THz and laser frequencies. Workshop discussion topics included advances in the understanding of the physics of breakdown and other phenomena, limiting high gradient performance of accelerating structures. New results presented in this workshop demonstrated significant progress in the fields of conventional vacuum structure-based acceleration, dielectric wakefield acceleration, and laser-structure acceleration.

  10. Prompt Gas Desorption Due to Ion Impact on Accelerator Structures

    NASA Astrophysics Data System (ADS)

    Vijay, Sagar; Seidl, Peter A.; Faltens, Andy; Lidia, Steven M.

    2011-10-01

    The repetition rate and peak current of high intensity ion accelerators for inertial fusion or other applications may be limited under certain conditions by the desorption of gas molecules and atoms due to stray ions striking the accelerator structure. We have measured the prompt yield of atoms in close proximity to the point of impact of the ions on a surface. Using the 300-keV, K+ ion beam of the Neutralized Drift Compression Experiment (NDCX-I), ions strike a metal target in a 5-10 microsecond bunch. The collector of a Bayert-Alpert style ionization gauge is used to detect the local pressure burst several centimeters away. Pressure transients are observed on a micro-second time scale due to the initial burst of desorbed gas, and on a much longer (~1 second) timescale, corresponding to the equilibration of the pressure after many ``bounces'' of atoms in the vacuum chamber. We report on these time dependent pressure measurements, modeling of the pressure transient, and implications for high-intensity ion accelerators. Work performed under auspices of U.S. DOE by LBNL under Contract DE-AC02-05CH1123.

  11. Design of an X-band accelerating structure using a newly developed structural optimization procedure

    NASA Astrophysics Data System (ADS)

    Huang, Xiaoxia; Fang, Wencheng; Gu, Qiang; Zhao, Zhentang

    2017-05-01

    An X-band high gradient accelerating structure is a challenging technology for implementation in advanced electron linear accelerator facilities. The present work discusses the design of an X-band accelerating structure for dedicated application to a compact hard X-ray free electron laser facility at the Shanghai Institute of Applied Physics, and numerous design optimizations are conducted with consideration for radio frequency (RF) breakdown, RF efficiency, short-range wakefields, and dipole/quadrupole field modes, to ensure good beam quality and a high accelerating gradient. The designed X-band accelerating structure is a constant gradient structure with a 4π/5 operating mode and input and output dual-feed couplers in a racetrack shape. The design process employs a newly developed effective optimization procedure for optimization of the X-band accelerating structure. In addition, the specific design of couplers providing high beam quality by eliminating dipole field components and reducing quadrupole field components is discussed in detail.

  12. Design parameters for the damped detuned accelerating structure

    SciTech Connect

    Ko, K.; Bane, K.; Gluckstern, R.; Hoag, H.; Kroll, N.; Lin, X.T.; Miller, R.; Ruth, R.; Thompson, K.; Wang, J. ||

    1995-06-01

    The advanced accelerating cavities for the NLCTA (and anticipated for NLC) will incorporate damping as well as detuning. The damping is provided by a set of four waveguides (which also serve as pumping manifolds) that run parallel to the structure, with strong iris coupling to each cavity cell and terminated at each end by absorbers. The previously reported equivalent circuit analysis has been refined and the dependence upon design parameters explored. The authors find that adequate damping can be provided by a single waveguide mode, leading to designs which are more compact than those initially considered. The design parameters and their rationale will be presented.

  13. Specifics of the microwave-breakdown mode in an accelerating structure with parallel coupling

    NASA Astrophysics Data System (ADS)

    Chernousov, Yu. D.; Shebolaev, I. V.

    2017-04-01

    The results of examination of the microwave-breakdown mode in an accelerating structure with parallel coupling are reported. It is demonstrated that breakdown normally occurs in a single cavity of the structure, while other cavities and the structure in general remain unaffected. This is attributed to the fact that neighboring accelerating cavities are almost independent of each other. This feature makes the structure more resistant to breakdown failure and may be used to increase the amplitude of the accelerating field in accelerators with a large number of accelerating structures.

  14. Studying Radiation Damage in Structural Materials by Using Ion Accelerators

    NASA Astrophysics Data System (ADS)

    Hosemann, Peter

    2011-02-01

    Radiation damage in structural materials is of major concern and a limiting factor for a wide range of engineering and scientific applications, including nuclear power production, medical applications, or components for scientific radiation sources. The usefulness of these applications is largely limited by the damage a material can sustain in the extreme environments of radiation, temperature, stress, and fatigue, over long periods of time. Although a wide range of materials has been extensively studied in nuclear reactors and neutron spallation sources since the beginning of the nuclear age, ion beam irradiations using particle accelerators are a more cost-effective alternative to study radiation damage in materials in a rather short period of time, allowing researchers to gain fundamental insights into the damage processes and to estimate the property changes due to irradiation. However, the comparison of results gained from ion beam irradiation, large-scale neutron irradiation, and a variety of experimental setups is not straightforward, and several effects have to be taken into account. It is the intention of this article to introduce the reader to the basic phenomena taking place and to point out the differences between classic reactor irradiations and ion irradiations. It will also provide an assessment of how accelerator-based ion beam irradiation is used today to gain insight into the damage in structural materials for large-scale engineering applications.

  15. Observation of Wakefield Suppression in a Photonic-Band-Gap Accelerator Structure

    SciTech Connect

    Simakov, Evgenya I.; Arsenyev, Sergey A.; Buechler, Cynthia E.; Edwards, Randall L.; Romero, William P.; Conde, Manoel; Ha, Gwanghui; Power, John G.; Wisniewski, Eric E.; Jing, Chunguang

    2016-02-10

    We report experimental observation of higher order mode (HOM) wakefield suppression in a room-temperature traveling-wave photonic band gap (PBG) accelerating structure at 11.700 GHz. It has been long recognized that PBG structures have potential for reducing long-range wakefields in accelerators. The first ever demonstration of acceleration in a room-temperature PBG structure was conducted in 2005. Since then, the importance of PBG accelerator research has been recognized by many institutions. However, the full experimental characterization of the wakefield spectrum and demonstration of wakefield suppression when the accelerating structure is excited by an electron beam has not been performed to date. We conducted an experiment at the Argonne Wakefield Accelerator (AWA) test facility and observed wakefields excited by a single high charge electron bunch when it passes through a PBG accelerator structure. Lastly, excellent HOM suppression properties of the PBG accelerator were demonstrated in the beam test.

  16. Observation of Wakefield Suppression in a Photonic-Band-Gap Accelerator Structure.

    PubMed

    Simakov, Evgenya I; Arsenyev, Sergey A; Buechler, Cynthia E; Edwards, Randall L; Romero, William P; Conde, Manoel; Ha, Gwanghui; Power, John G; Wisniewski, Eric E; Jing, Chunguang

    2016-02-12

    We report experimental observation of higher order mode (HOM) wakefield suppression in a room-temperature traveling-wave photonic-band-gap (PBG) accelerating structure at 11.700 GHz. It has been long recognized that PBG structures have the potential for reducing long-range wakefields in accelerators. The first ever demonstration of acceleration in a room-temperature PBG structure was conducted in 2005. Since then, the importance of PBG accelerator research has been recognized by many institutions. However, the full experimental characterization of the wakefield spectrum and demonstration of wakefield suppression when the accelerating structure is excited by an electron beam has not been performed to date. We conducted an experiment at the Argonne Wakefield Accelerator test facility and observed wakefields excited by a single high charge electron bunch when it passes through a PBG accelerator structure. Excellent HOM suppression properties of the PBG accelerator were demonstrated in the beam test.

  17. Observation of Wakefield Suppression in a Photonic-Band-Gap Accelerator Structure

    NASA Astrophysics Data System (ADS)

    Simakov, Evgenya I.; Arsenyev, Sergey A.; Buechler, Cynthia E.; Edwards, Randall L.; Romero, William P.; Conde, Manoel; Ha, Gwanghui; Power, John G.; Wisniewski, Eric E.; Jing, Chunguang

    2016-02-01

    We report experimental observation of higher order mode (HOM) wakefield suppression in a room-temperature traveling-wave photonic-band-gap (PBG) accelerating structure at 11.700 GHz. It has been long recognized that PBG structures have the potential for reducing long-range wakefields in accelerators. The first ever demonstration of acceleration in a room-temperature PBG structure was conducted in 2005. Since then, the importance of PBG accelerator research has been recognized by many institutions. However, the full experimental characterization of the wakefield spectrum and demonstration of wakefield suppression when the accelerating structure is excited by an electron beam has not been performed to date. We conducted an experiment at the Argonne Wakefield Accelerator test facility and observed wakefields excited by a single high charge electron bunch when it passes through a PBG accelerator structure. Excellent HOM suppression properties of the PBG accelerator were demonstrated in the beam test.

  18. Observation of Wakefield Suppression in a Photonic-Band-Gap Accelerator Structure

    DOE PAGES

    Simakov, Evgenya I.; Arsenyev, Sergey A.; Buechler, Cynthia E.; ...

    2016-02-10

    We report experimental observation of higher order mode (HOM) wakefield suppression in a room-temperature traveling-wave photonic band gap (PBG) accelerating structure at 11.700 GHz. It has been long recognized that PBG structures have potential for reducing long-range wakefields in accelerators. The first ever demonstration of acceleration in a room-temperature PBG structure was conducted in 2005. Since then, the importance of PBG accelerator research has been recognized by many institutions. However, the full experimental characterization of the wakefield spectrum and demonstration of wakefield suppression when the accelerating structure is excited by an electron beam has not been performed to date. Wemore » conducted an experiment at the Argonne Wakefield Accelerator (AWA) test facility and observed wakefields excited by a single high charge electron bunch when it passes through a PBG accelerator structure. Lastly, excellent HOM suppression properties of the PBG accelerator were demonstrated in the beam test.« less

  19. RF properties of periodic accelerating structures for linear colliders

    SciTech Connect

    Wang, J.W.

    1989-07-01

    With the advent of the SLAC electron-positron linear collider (SLC) in the 100 GeV center-of-mass energy range, research and development work on even higher energy machines of this type has started in several laboratories in the United States, Europe, the Soviet Union and Japan. These linear colliders appear to provide the only promising approach to studying e/sup /plus//e/sup /minus// physics at center-of-mass energies approaching 1 TeV. This thesis concerns itself with the study of radio frequency properties of periodic accelerating structures for linear colliders and their interaction with bunched beams. The topics that have been investigated are: experimental measurements of the energy loss of single bunches to longitudinal modes in two types of structures, using an equivalent signal on a coaxial wire to simulate the beam; a method of canceling the energy spread created within a single bunch by longitudinal wakefields, through appropriate shaping of the longitudinal charge distribution of the bunch; derivation of the complete transient beam-loading equation for a train of bunches passing through a constant-gradient accelerator section, with application to the calculation and minimization of multi-bunch energy spread; detailed study of field emission and radio frequency breakdown in disk-loaded structures at S-, C- and X-band frequencies under extremely high-gradient conditions, with special attention to thermal effects, radiation, sparking, emission of gases, surface damage through explosive emission and its possible control through RF-gas processing. 53 refs., 49 figs., 9 tabs.

  20. Comparative study of medium damped and detuned linear accelerator structures

    SciTech Connect

    Jean-Francois Ostiguy et al.

    2001-08-22

    Long range wakefields are a serious concern for a future linear collider based on room temperature accelerating structures. They can be suppressed either by detuning and or local damping or with some combination of both strategies. Detuning relies on precisely phasing the contributions of the dipole modes excited by the passage of a single bunch. This is accomplished by controlling individual mode frequencies, a process which dictates individual cell dimensional tolerances. Each mode must be excited with the correct strength; this in turn, determines cell-to-cell alignment tolerances. In contrast, in a locally damped structure, the modes are attenuated at the cell level. Clearly, mode frequencies and relative excitation become less critical in that context; mechanical fabrication tolerances can be relaxed. While local damping is ideal from the stand-point of long range wakefield suppression, this comes at the cost of reducing the shunt impedance and possibly unacceptable localized heating. Recently, the Medium Damped Structure (MDS), a compromise between detuning and local damping, has generated some interest. In this paper, we compare a hypothetical MDS to the NLC Rounded Damped Detuned Structure (RDDS) and investigate possible advantages from the standpoint fabrication tolerances and their relation to beam stability and emittance preservation.

  1. Accelerated protein structure comparison using TM-score-GPU

    PubMed Central

    Hung, Ling-Hong; Samudrala, Ram

    2012-01-01

    Motivation: Accurate comparisons of different protein structures play important roles in structural biology, structure prediction and functional annotation. The root-mean-square-deviation (RMSD) after optimal superposition is the predominant measure of similarity due to the ease and speed of computation. However, global RMSD is dependent on the length of the protein and can be dominated by divergent loops that can obscure local regions of similarity. A more sophisticated measure of structure similarity, Template Modeling (TM)-score, avoids these problems, and it is one of the measures used by the community-wide experiments of critical assessment of protein structure prediction to compare predicted models with experimental structures. TM-score calculations are, however, much slower than RMSD calculations. We have therefore implemented a very fast version of TM-score for Graphical Processing Units (TM-score-GPU), using a new and novel hybrid Kabsch/quaternion method for calculating the optimal superposition and RMSD that is designed for parallel applications. This acceleration in speed allows TM-score to be used efficiently in computationally intensive applications such as for clustering of protein models and genome-wide comparisons of structure. Results: TM-score-GPU was applied to six sets of models from Nutritious Rice for the World for a total of 3 million comparisons. TM-score-GPU is 68 times faster on an ATI 5870 GPU, on average, than the original CPU single-threaded implementation on an AMD Phenom II 810 quad-core processor. Availability and implementation: The complete source, including the GPU code and the hybrid RMSD subroutine, can be downloaded and used without restriction at http://software.compbio.washington.edu/misc/downloads/tmscore/. The implementation is in C++/OpenCL. Contact: ram@compbio.washington.edu Supplementary Information: Supplementary data are available at Bioinformatics online. PMID:22718788

  2. Accelerated protein structure comparison using TM-score-GPU.

    PubMed

    Hung, Ling-Hong; Samudrala, Ram

    2012-08-15

    Accurate comparisons of different protein structures play important roles in structural biology, structure prediction and functional annotation. The root-mean-square-deviation (RMSD) after optimal superposition is the predominant measure of similarity due to the ease and speed of computation. However, global RMSD is dependent on the length of the protein and can be dominated by divergent loops that can obscure local regions of similarity. A more sophisticated measure of structure similarity, Template Modeling (TM)-score, avoids these problems, and it is one of the measures used by the community-wide experiments of critical assessment of protein structure prediction to compare predicted models with experimental structures. TM-score calculations are, however, much slower than RMSD calculations. We have therefore implemented a very fast version of TM-score for Graphical Processing Units (TM-score-GPU), using a new and novel hybrid Kabsch/quaternion method for calculating the optimal superposition and RMSD that is designed for parallel applications. This acceleration in speed allows TM-score to be used efficiently in computationally intensive applications such as for clustering of protein models and genome-wide comparisons of structure. TM-score-GPU was applied to six sets of models from Nutritious Rice for the World for a total of 3 million comparisons. TM-score-GPU is 68 times faster on an ATI 5870 GPU, on average, than the original CPU single-threaded implementation on an AMD Phenom II 810 quad-core processor. The complete source, including the GPU code and the hybrid RMSD subroutine, can be downloaded and used without restriction at http://software.compbio.washington.edu/misc/downloads/tmscore/. The implementation is in C++/OpenCL.

  3. Design of a 30 GHz Damped Detuned Accelerating Structure

    NASA Astrophysics Data System (ADS)

    Dehler, M.; Wilson, I.; Wuensch, W.; Jones, R. M.; Kroll, N. M.; Miller, R. H.

    1997-05-01

    Within the framework of the SLAC/CERN studies of 30 GHz linear colliders, an attempt has been made to scale the existing X-band NLC damped detuned accelerating structure to 30 GHz. A simple scaling was not chosen because of anticipated manufacturing difficulties. The new manifold-damped design has 101 cells and a minimum aperture of 3.4 mm. In order to obtain acceptably small values for both the single-bunch transverse wakefield and the long-range multibunch wakefield a relatively large non-linear variation of the iris thickness was introduced in addition to the iris diameter variation. The resulting short-range wakefield is 1270 V/pC/mm/m decreasing to less than 1after 1 ns.

  4. Deamidation accelerates amyloid formation and alters amylin fiber structure

    PubMed Central

    Dunkelberger, Emily B.; Buchanan, Lauren E.; Marek, Peter; Cao, Ping; Raleigh, Daniel P.; Zanni, Martin T.

    2012-01-01

    Deamidation of asparagine and glutamine is the most common non-enzymatic, post-translational modification. Deamidation can influence the structure, stability, folding, and aggregation of proteins and has been proposed to play a role in amyloid formation. However there are no structural studies of the consequences of deamidation on amyloid fibers, in large part because of the difficulty of studying these materials using conventional methods. Here we examine the effects of deamidation on the kinetics of amyloid formation by amylin, the causative agent of type 2 diabetes. We find that deamidation accelerates amyloid formation and the deamidated material is able to seed amyloid formation by unmodified amylin. Using site-specific isotope labeling and two-dimensional infrared (2D IR) spectroscopy, we show that fibers formed by samples that contain deamidated polypeptide contain reduced amounts of β-sheet. Deamidation leads to disruption of the N-terminal β-sheet between Ala-8 and Ala-13, but β-sheet is still retained near Leu-16. The C-terminal sheet is disrupted near Leu-27. Analysis of potential sites of deamidation together with structural models of amylin fibers reveals that deamidation in the N-terminal β-sheet region may be the cause for the disruption of the fiber structure at both the N- and C-terminal β-sheet. Thus, deamidation is a post-translational modification that creates fibers which have an altered structure, but can still act as a template for amylin aggregation. Deamidation is very difficult to detect with standard methods used to follow amyloid formation, but isotope labeled IR spectroscopy provides a means for monitoring sample degradation and investigating the structural consequences of deamidation. PMID:22734583

  5. THE SPECIFIC ACCELERATION RATE IN LOOP-STRUCTURED SOLAR FLARES-IMPLICATIONS FOR ELECTRON ACCELERATION MODELS

    SciTech Connect

    Guo, Jingnan; Emslie, A. Gordon; Piana, Michele E-mail: piana@dima.unige.it

    2013-03-20

    We analyze electron flux maps based on RHESSI hard X-ray imaging spectroscopy data for a number of extended coronal-loop flare events. For each event, we determine the variation of the characteristic loop length L with electron energy E, and we fit this observed behavior with models that incorporate an extended acceleration region and an exterior 'propagation' region, and which may include collisional modification of the accelerated electron spectrum inside the acceleration region. The models are characterized by two parameters: the plasma density n in, and the longitudinal extent L{sub 0} of, the acceleration region. Determination of the best-fit values of these parameters permits inference of the volume that encompasses the acceleration region and of the total number of particles within it. It is then straightforward to compute values for the emission filling factor and for the specific acceleration rate (electrons s{sup -1} per ambient electron above a chosen reference energy). For the 24 events studied, the range of inferred filling factors is consistent with a value of unity. The inferred mean value of the specific acceleration rate above E{sub 0} = 20 keV is {approx}10{sup -2} s{sup -1}, with a 1{sigma} spread of about a half-order-of-magnitude above and below this value. We compare these values with the predictions of several models, including acceleration by large-scale, weak (sub-Dreicer) fields, by strong (super-Dreicer) electric fields in a reconnecting current sheet, and by stochastic acceleration processes.

  6. Field analysis of a dielectric-loaded rectangular waveguide accelerating structure

    NASA Astrophysics Data System (ADS)

    Xiao, Liling; Gai, Wei; Sun, Xiang

    2002-01-01

    Recently, there has been some interest in planar or rectangular dielectric accelerating structures for future high-gradient linear accelerators. In this paper, we present a detailed analysis of the modes of a dielectric-loaded rectangular waveguide accelerating structure based on a circuit model approximation and mode matching method. In general, the acceleration field in a synchronous acceleration mode is nonuniform in the two transverse dimensions. We show, however, that by using a series of rectangular structures successively rotated by 90°, the net accelerating force can be made almost uniform. Characteristic parameters such as R/Q, group velocity, and attenuation constant for X- and W-band accelerators are calculated. The longitudinal wakefields experienced by a relativistic charged particle beam in these structures are also presented. These analytical results are also compared with numerical calculations using the MAFIA code suite demonstrating the validity of our analytic approach.

  7. Field analysis of a dielectric-loaded rectangular waveguide accelerating structure.

    PubMed

    Xiao, Liling; Gai, Wei; Sun, Xiang

    2002-01-01

    Recently, there has been some interest in planar or rectangular dielectric accelerating structures for future high-gradient linear accelerators. In this paper, we present a detailed analysis of the modes of a dielectric-loaded rectangular waveguide accelerating structure based on a circuit model approximation and mode matching method. In general, the acceleration field in a synchronous acceleration mode is nonuniform in the two transverse dimensions. We show, however, that by using a series of rectangular structures successively rotated by 90 degrees, the net accelerating force can be made almost uniform. Characteristic parameters such as R/Q, group velocity, and attenuation constant for X- and W-band accelerators are calculated. The longitudinal wakefields experienced by a relativistic charged particle beam in these structures are also presented. These analytical results are also compared with numerical calculations using the MAFIA code suite demonstrating the validity of our analytic approach.

  8. Superconducting Accelerating Structure for High-Current Cyclotrons for Accelerator-Driven Subcritical Fission

    NASA Astrophysics Data System (ADS)

    Pogue, Nathaniel; McIntyre, Peter; Sattarov, Akhdiyor

    2011-10-01

    An accelerator driven molten salt fission core is being designed to provide reliable power by subcritical nuclear fission for the next few millennia. Fission is driven by proton beams from a flux-coupled stack of three high-current cyclotrons. A key innovation in attaining the needed beam current and efficiency is a superconducting Niobium rf accelerating cavity that can accelerate bunches in the 200 orbits uniformly. The unique design allows for several cavities to be stacked, and also provides uniform acceleration and eliminates higher order modes in the cyclotron. The design and properties of the superconducting cavity will increase the efficiency of the cyclotron and the overall energy amplification from the molten salt core by an order of magnitude compared to conventional designs.

  9. Comparisons of radio frequency technology for superconducting accelerating structures

    NASA Astrophysics Data System (ADS)

    Kimber, Andrew J.

    2015-12-01

    Since the introduction of radiofrequency (RF) accelerating cavities, normal conducting as well as superconducting, there has been a need to drive them with RF power. At first glance, the function of an RF drive system may seem simple and straightforward, but this belies subtleties that greatly affect the performance of the cavity itself, diminishing efforts in perfecting techniques in design and manufacture. It can also contribute to a significant portion of the initial capital and ongoing running costs of a facility, maintenance labor, downtime and future expenditure as the system ages. The RF `system', should be thought of as just that, the entire collection of components from wall plug to cavity. Following this integrated approach will enable the system to meet or exceed its design goals. This paper seeks to review the current state of RF technology for superconducting structures and to compare these technologies, looking at what has traditionally been used, developments that have enabled higher efficiencies and higher reliabilities as well as looking towards future technologies. It will concentrate on superconducting applications, but much of the narrative is equally applicable to normal conducting structures as well.

  10. Electron acceleration by an electromagnetic wave propagating across a magnetic field in periodic structures

    NASA Astrophysics Data System (ADS)

    Buts, V. A.; Ognivenko, V. V.

    1990-05-01

    The possibility of the acceleration of charged particles captured by an electromagnetic wave propagating across a constant magnetic field in periodic slow-wave structures is demonstrated. A plane waveguide with perfectly conducting walls is examined as an example of an electrodynamic structure in which such an acceleration mechanism is possible. The acceleration rate is determined, and the stability of captured particle motion is investigated.

  11. Development of High-Gradient Dielectric Laser-Driven Particle Accelerator Structures

    SciTech Connect

    Byer, Robert L.

    2013-11-07

    The thrust of Stanford's program is to conduct research on high-gradient dielectric accelerator structures driven with high repetition-rate, tabletop infrared lasers. The close collaboration between Stanford and SLAC (Stanford Linear Accelerator Center) is critical to the success of this project, because it provides a unique environment where prototype dielectric accelerator structures can be rapidly fabricated and tested with a relativistic electron beam.

  12. Accelerate!

    PubMed

    Kotter, John P

    2012-11-01

    The old ways of setting and implementing strategy are failing us, writes the author of Leading Change, in part because we can no longer keep up with the pace of change. Organizational leaders are torn between trying to stay ahead of increasingly fierce competition and needing to deliver this year's results. Although traditional hierarchies and managerial processes--the components of a company's "operating system"--can meet the daily demands of running an enterprise, they are rarely equipped to identify important hazards quickly, formulate creative strategic initiatives nimbly, and implement them speedily. The solution Kotter offers is a second system--an agile, networklike structure--that operates in concert with the first to create a dual operating system. In such a system the hierarchy can hand off the pursuit of big strategic initiatives to the strategy network, freeing itself to focus on incremental changes to improve efficiency. The network is populated by employees from all levels of the organization, giving it organizational knowledge, relationships, credibility, and influence. It can Liberate information from silos with ease. It has a dynamic structure free of bureaucratic layers, permitting a level of individualism, creativity, and innovation beyond the reach of any hierarchy. The network's core is a guiding coalition that represents each level and department in the hierarchy, with a broad range of skills. Its drivers are members of a "volunteer army" who are energized by and committed to the coalition's vividly formulated, high-stakes vision and strategy. Kotter has helped eight organizations, public and private, build dual operating systems over the past three years. He predicts that such systems will lead to long-term success in the 21st century--for shareholders, customers, employees, and companies themselves.

  13. Design of RF Feed System for Standing-Wave Accelerator Structures

    SciTech Connect

    Neilson, J.; Tantawi, S.; Dolgashev, V.; /SLAC

    2012-05-25

    We are investigating a standing wave accelerator structure that uses a rf feed to each individual cell. This approach minimizes rf power flow and electromagnetic energy absorbed by an rf breakdown. The objective of this work is a robust high-gradient (above 100 MV/m) X-band accelerator structure.

  14. The structure of heart rate asymmetry: deceleration and acceleration runs.

    PubMed

    Piskorski, J; Guzik, P

    2011-08-01

    A family of new heart rate asymmetry measures is introduced, namely deceleration and acceleration runs, as well as entropic measures summarizing their distribution. We introduce the theoretical run distribution for shuffled data and use it as a reference for interpreting the results. The measures defined in the paper are applied to actual 24 h Holter ECG recordings from 87 healthy people, and it is demonstrated that the patterns of accelerations are different from those of decelerations. Acceleration runs are longer and more numerous: all runs of accelerations, with the exception of lengths 3 and 4, are more numerous than those of decelerations. These findings are reflected in the difference between the entropic measures for acceleration and deceleration runs: for 74 subjects the acceleration-related entropic parameter is greater than that of decelerations (p < 0.001). For shuffled data there is no difference in the above parameters, and there are more short runs and fewer long runs than in physiological data. The influence of the measuring equipment resolution is also discussed.

  15. X-band dielectric loaded RF driven accelerator structures: Theoretical and experimental investigations

    NASA Astrophysics Data System (ADS)

    Zou, Peng

    An important area of application of high-power radio frequency (RF) and microwave sources is particle acceleration. A major challenge for the current worldwide research and development effort in linear accelerator is the search for a compact and affordable very-high-energy accelerator technology for the next generation supercolliders. It has been recognized for sometime that dielectric loaded accelerator structures are attractive candidates for the next generation very-high-energy linear accelerators, because they possess several distinct advantages over conventional metallic iris- loaded accelerator structures. However, some fundamental issues, such as RF breakdown in the dielectric, Joule heating, and vacuum properties of dielectric materials, are still the subjects of intense investigation, requiring the validation by experiments conducted at high power levels. An X-band traveling-wave accelerator based on dielectric-lined waveguide has been designed and constructed. Numerical calculation, bench measurements, and 3-D electromagnetic field simulation of this dielectric loaded accelerator are presented. One critical technical problem in constructing such dielectric loaded accelerator is efficient coupling of RF power into the dielectric-lined circular waveguide. A coupling scheme has been arrived at by empirical methods. Field distribution in this coupling configuration has been studied by numerical simulation. In the conventional iris-loaded accelerator structures, the peak surface electric field E s is in general found to be at least a factor of 2 higher than the axial acceleration field Ea. Because the peak surface electric field causes electric breakdown of the structure, it represents a direct limitation on the maximum acceleration gradient that can be obtained. A novel hybrid dielectric-iris-loaded periodic accelerator structure is proposed to utilize the advantages of both dielectric-lined waveguides and conventional iris-loaded structures. Numerical

  16. Simulation Studies of the Dielectric Grating as an Accelerating and Focusing Structure

    SciTech Connect

    Soong, Ken; Peralta, E.A.; Byer, R.L.; Colby, E.; /SLAC

    2011-08-12

    A grating-based design is a promising candidate for a laser-driven dielectric accelerator. Through simulations, we show the merits of a readily fabricated grating structure as an accelerating component. Additionally, we show that with a small design perturbation, the accelerating component can be converted into a focusing structure. The understanding of these two components is critical in the successful development of any complete accelerator. The concept of accelerating electrons with the tremendous electric fields found in lasers has been proposed for decades. However, until recently the realization of such an accelerator was not technologically feasible. Recent advances in the semiconductor industry, as well as advances in laser technology, have now made laser-driven dielectric accelerators imminent. The grating-based accelerator is one proposed design for a dielectric laser-driven accelerator. This design, which was introduced by Plettner, consists of a pair of opposing transparent binary gratings, illustrated in Fig. 1. The teeth of the gratings serve as a phase mask, ensuring a phase synchronicity between the electromagnetic field and the moving particles. The current grating accelerator design has the drive laser incident perpendicular to the substrate, which poses a laser-structure alignment complication. The next iteration of grating structure fabrication seeks to monolithically create an array of grating structures by etching the grating's vacuum channel into a fused silica wafer. With this method it is possible to have the drive laser confined to the plane of the wafer, thus ensuring alignment of the laser-and-structure, the two grating halves, and subsequent accelerator components. There has been previous work using 2-dimensional finite difference time domain (2D-FDTD) calculations to evaluate the performance of the grating accelerator structure. However, this work approximates the grating as an infinite structure and does not accurately model a

  17. Structure-based, high transformer ratio collinear two-beam accelerator

    NASA Astrophysics Data System (ADS)

    Jiang, Yong; Shchelkunov, Sergey V.; Hirshfield, Jay L.

    2017-03-01

    A novel concept for a structure-based collinear two-beam accelerator is described. By employing a structure composed of multi-harmonic detuned cavities, this new accelerator can provide a high acceleration gradient with a high transformer ratio and a low breakdown probability. An experimental research project, with theoretical and computational support, is being conducted at the Yale University Beam Physics Laboratory. Furthermore, this project will support construction of a unique university-based facility for exploring a range of beam-driven acceleration ideas, including plasma and dielectric wakefield concepts.

  18. Fabrication and tuning techniques for side-coupled electron accelerator structures

    SciTech Connect

    Hansborough, L.D.; Clark, W.L.; DePaula, R.A.; Martinez, F.A.; Roybal, P.L.; Wilkerson, L.C.; Young, L.M.

    1986-01-01

    Beginning in 1979, Los Alamos entered into a collaboration with the National Bureau of Standards (NBS) to develop an advanced cw microtron accelerator. The accelerating structures (one 0.9-m-long, one 2.7-m-long, and two 4.0-m-long) containing a total of 184 accelerating cavities have been fabricated and tuned to the 2380-MHz operating frequency. New methods simplified the fabrication of these structures and eliminated several furnace-brazing steps. These fabrication methods, lathe-mounted tuning fixtures, and streamlined tuning techniques were developed to allow efficient production of side-coupled structures. These techniques are now being applied to the 2450-MHz racetrack microtron accelerator structures being fabricated at Los Alamos for the Nuclear Physics Department of the University of Illinois. Refinements of the described techniques will allow future accelerators of this type to be fabricated by private industry.

  19. Formation of electrostatic structures by wakefield acceleration in ultrarelativistic plasma flows: Electron acceleration to cosmic ray energies

    SciTech Connect

    Dieckmann, M.E.; Shukla, P.K.; Eliasson, B.

    2006-06-15

    The ever increasing performance of supercomputers is now enabling kinetic simulations of extreme astrophysical and laser produced plasmas. Three-dimensional particle-in-cell (PIC) simulations of relativistic shocks have revealed highly filamented spatial structures and their ability to accelerate particles to ultrarelativistic speeds. However, these PIC simulations have not yet revealed mechanisms that could produce particles with tera-electron volt energies and beyond. In this work, PIC simulations in one dimension (1D) of the foreshock region of an internal shock in a gamma ray burst are performed to address this issue. The large spatiotemporal range accessible to a 1D simulation enables the self-consistent evolution of proton phase space structures that can accelerate particles to giga-electron volt energies in the jet frame of reference, and to tens of tera-electron volt in the Earth's frame of reference. One potential source of ultrahigh energy cosmic rays may thus be the thermalization of relativistically moving plasma.

  20. Superconducting accelerating structures for very low velocity ion beams

    SciTech Connect

    Xu, J.; Shepard, K.W.; Ostroumov, P.N.; Fuerst, J.D.; Waldschmidt, G.; Gonin, I.V.; /Fermilab

    2008-01-01

    This paper presents designs for four types of very-low-velocity superconducting accelerating cavity capable of providing several MV of accelerating potential per cavity, and suitable for particle velocities in the range 0.006 < v/c < 0.06. Superconducting TEM-class cavities have been widely applied to CW acceleration of ion beams. SC linacs can be formed as an array of independently-phased cavities, enabling a variable velocity profile to maximize the output energy for each of a number of different ion species. Several laboratories in the US and Europe are planning exotic beam facilities based on SC linacs. The cavity designs presented here are intended for the front-end of such linacs, particularly for the post-acceleration of rare isotopes of low charge state. Several types of SC cavities have been developed recently to cover particle velocities above 0.06c. Superconducting four-gap quarter-wave resonators for velocities 0.008 < {beta} = v/c < 0.05 were developed about two decades ago and have been successfully operated at the ATLAS SC linac at Argonne National Laboratory. Since that time, progress in simulation tools, cavity fabrication and processing have increased SC cavity gradients by a factor of 3-4. This paper applies these tools to optimize the design of a four-gap quarter-wave resonator for exotic beam facilities and other low-velocity applications.

  1. Computer simulation of the coupling slots effects for on-axis coupled accelerating structures.

    NASA Astrophysics Data System (ADS)

    Salakhoutdinov, A. F.; Shvedunov, V. I.

    1997-05-01

    The presence of coupling elements in accelerating structures leads to the violation of axial symmetry of accelerating field and it may cause displacement, defocusing and non-linear distortion of phase space. As a result the growth of transverse emittance occures. From the other hand, these effects may be used for designing of RF- focusing accelerating structure for electron accelerators of various types. The numerical simulation of electrodynamical properties of on-axis coupled accelerating structure taking into account the coupling slots have been made. The characteristics of fields excited within the coupling cell have been investigated. The numerical estimations of various multipolarity components of transverse forces acting upon a particle inside the coupling cell have been achieved.

  2. Numerically optimized structures for dielectric asymmetric dual-grating laser accelerators

    SciTech Connect

    Aimidula, A.; Bake, M. A.; Wan, F.; Xie, B. S.; Welsch, C. P.; Xia, G.; Mete, O.; Uesaka, M.; Matsumura, Y.; Yoshida, M.; Koyama, K.

    2014-02-15

    Optical scale dielectric structures are promising candidates to realize future compact, low cost particle accelerators, since they can sustain high acceleration gradients in the range of GeV/m. Here, we present numerical simulation results for a dielectric asymmetric dual-grating accelerator. It was found that the asymmetric dual-grating structures can efficiently modify the laser field to synchronize it with relativistic electrons, therefore increasing the average acceleration gradient by ∼10% in comparison to symmetric structures. The optimum pillar height which was determined by simulation agrees well with that estimated analytically. The effect of the initial kinetic energy of injected electrons on the acceleration gradient is also discussed. Finally, the required laser parameters were calculated analytically and a suitable laser is proposed as energy source.

  3. On the RF Distribution System for a Set of Standing-Wave Accelerator Structures

    SciTech Connect

    Tantawi, Sami G.; /SLAC

    2006-09-28

    In this paper, we study the RF feeding system for a set of standing-wave accelerator structures. To avoid the initial reflections produced by the structures, sometimes these structures are fed in pairs through a four-port 3-dB Hybrid. We present an extension to this system for an arbitrary number of accelerator structures and show it is always possible to cancel the reflection back to the source. The necessary and sufficient condition for this to happen depends only on the spacing between accelerator structures. In this system, the structures are not fed in a binary hierarchal system, rather in series with a set of directional couplers designed to bleed off an equal amount of power to each accelerator structure in the set. We study the sensitivity of such a system to errors resulting from the differences in accelerator structures spacing. We also study the sensitivity of the system to component imperfections, such as the finite directivity of the directional couplers, and the residual reflections from the loads that are attached to these couplers. We also study the system under fault conditions, such as a breakdown in an accelerator structure or a feed waveguide.

  4. Experimental demonstration of wakefield effects in a THz planar diamond accelerating structure

    SciTech Connect

    Antipov, S.; Jing, C.; Kanareykin, A.; Butler, J. E.; Yakimenko, V.; Fedurin, M.; Kusche, K.; Gai, W.

    2012-03-26

    We have directly measured THz wakefields induced by a subpicosecond, intense relativistic electron bunch in a diamond loaded accelerating structure via the wakefield acceleration method. We present here the beam test results from the diamond based structure. Diamond has been chosen for its high breakdown threshold and unique thermoconductive properties. Fields produced by a leading (drive) beam were used to accelerate a trailing (witness) electron bunch, which followed the drive bunch at a variable distance. The energy gain of a witness bunch as a function of its separation from the drive bunch describes the time structure of the generated wakefield.

  5. SLAC High Gradient Testing of a KEK X-Band Accelerator Structure

    SciTech Connect

    Loewen, Rod

    2000-03-30

    The high accelerating gradients required for future linear colliders demands a better study of field emission and RF breakdown in accelerator structures. Changes in structure geometry, vacuum pumping, fabrication methods, and surface finish can all potentially impact the conditioning process, dark current emission, and peak RF power handling capability. Recent tests at SLAC of KEK's ``M2'' travelling wave x-band accelerator section provides an opportunity to investigate some of these effects by comparing its performance to previously high power tested structures at SLAC. In addition to studying ultimate power limitations, this test also demonstrates the use of computer automated conditioning to reach practical, achievable gradients.

  6. The development of a TESLA recirculator with superconducting accelerating structures in Ukraine

    NASA Astrophysics Data System (ADS)

    Guk, I. S.; Dovbnya, A. N.

    2008-12-01

    The recirculator project, which is to be built at the National Science Center, Kharkov Institute of Physics and Technology (NSC KIPT), is presented. The basic solutions incorporated in the design are given. The TESLA superconducting section is chosen as the accelerating structure of an accelerating complex.

  7. Accelerating simulation of ensembles of locally differing optical structures via a Schur complement domain decomposition.

    PubMed

    Verweij, Sacha; Liu, Victor; Fan, Shanhui

    2014-11-15

    We present a Schur complement domain decomposition method that can significantly accelerate simulation of ensembles of locally differing optical structures. We apply the method to design a multi-spatial-mode photonic crystal waveguide splitter that exhibits high transmission and preservation of modal content, showing design acceleration by more than a factor of 20.

  8. e-/e+ Accelerating Structure with Cyclic Variation of Azimuth Asymmetry

    SciTech Connect

    Krasnykh, A.; /SLAC

    2007-03-05

    A classical electron/positron accelerating structure is a disk-loaded cylindrical waveguide. The accelerator structure here has azimuth symmetry. The proposed structure contains a disk-loaded cylindrical waveguide where there is a periodical change of RF-field vs. azimuth. The modulation deforms the rf-field in such a manner that the accelerated particles undergo transverse focusing forces. The new class of accelerator structures covers the initial part of e+/e- linacs where a bunch is not rigid and additional transverse focusing fields are necessary. We discuss a bunch formation with a high transverse aspect ratio in the proposed structure and particularly in the photoinjector part of a linac.

  9. Free electron laser using Rf coupled accelerating and decelerating structures

    DOEpatents

    Brau, Charles A.; Swenson, Donald A.; Boyd, Jr., Thomas J.

    1984-01-01

    A free electron laser and free electron laser amplifier using beam transport devices for guiding an electron beam to a wiggler of a free electron laser and returning the electron beam to decelerating cavities disposed adjacent to the accelerating cavities of the free electron laser. Rf energy is generated from the energy depleted electron beam after it emerges from the wiggler by means of the decelerating cavities which are closely coupled to the accelerating cavities, or by means of a second bore within a single set of cavities. Rf energy generated from the decelerated electron beam is used to supplement energy provided by an external source, such as a klystron, to thereby enhance overall efficiency of the system.

  10. Linear particle accelerator with seal structure between electrodes and insulators

    DOEpatents

    Broadhurst, John H.

    1989-01-01

    An electrostatic linear accelerator includes an electrode stack comprised of primary electrodes formed or Kovar and supported by annular glass insulators having the same thermal expansion rate as the electrodes. Each glass insulator is provided with a pair of fused-in Kovar ring inserts which are bonded to the electrodes. Each electrode is designed to define a concavo-convex particle trap so that secondary charged particles generated within the accelerated beam area cannot reach the inner surface of an insulator. Each insulator has a generated inner surface profile which is so configured that the electrical field at this surface contains no significant tangential component. A spark gap trigger assembly is provided, which energizes spark gaps protecting the electrodes affected by over voltage to prevent excessive energy dissipation in the electrode stack.

  11. A compact linear accelerator based on a scalable microelectromechanical-system RF-structure

    NASA Astrophysics Data System (ADS)

    Persaud, A.; Ji, Q.; Feinberg, E.; Seidl, P. A.; Waldron, W. L.; Schenkel, T.; Lal, A.; Vinayakumar, K. B.; Ardanuc, S.; Hammer, D. A.

    2017-06-01

    A new approach for a compact radio-frequency (RF) accelerator structure is presented. The new accelerator architecture is based on the Multiple Electrostatic Quadrupole Array Linear Accelerator (MEQALAC) structure that was first developed in the 1980s. The MEQALAC utilized RF resonators producing the accelerating fields and providing for higher beam currents through parallel beamlets focused using arrays of electrostatic quadrupoles (ESQs). While the early work obtained ESQs with lateral dimensions on the order of a few centimeters, using a printed circuit board (PCB), we reduce the characteristic dimension to the millimeter regime, while massively scaling up the potential number of parallel beamlets. Using Microelectromechanical systems scalable fabrication approaches, we are working on further reducing the characteristic dimension to the sub-millimeter regime. The technology is based on RF-acceleration components and ESQs implemented in the PCB or silicon wafers where each beamlet passes through beam apertures in the wafer. The complete accelerator is then assembled by stacking these wafers. This approach has the potential for fast and inexpensive batch fabrication of the components and flexibility in system design for application specific beam energies and currents. For prototyping the accelerator architecture, the components have been fabricated using the PCB. In this paper, we present proof of concept results of the principal components using the PCB: RF acceleration and ESQ focusing. Ongoing developments on implementing components in silicon and scaling of the accelerator technology to high currents and beam energies are discussed.

  12. A compact linear accelerator based on a scalable microelectromechanical-system RF-structure.

    PubMed

    Persaud, A; Ji, Q; Feinberg, E; Seidl, P A; Waldron, W L; Schenkel, T; Lal, A; Vinayakumar, K B; Ardanuc, S; Hammer, D A

    2017-06-01

    A new approach for a compact radio-frequency (RF) accelerator structure is presented. The new accelerator architecture is based on the Multiple Electrostatic Quadrupole Array Linear Accelerator (MEQALAC) structure that was first developed in the 1980s. The MEQALAC utilized RF resonators producing the accelerating fields and providing for higher beam currents through parallel beamlets focused using arrays of electrostatic quadrupoles (ESQs). While the early work obtained ESQs with lateral dimensions on the order of a few centimeters, using a printed circuit board (PCB), we reduce the characteristic dimension to the millimeter regime, while massively scaling up the potential number of parallel beamlets. Using Microelectromechanical systems scalable fabrication approaches, we are working on further reducing the characteristic dimension to the sub-millimeter regime. The technology is based on RF-acceleration components and ESQs implemented in the PCB or silicon wafers where each beamlet passes through beam apertures in the wafer. The complete accelerator is then assembled by stacking these wafers. This approach has the potential for fast and inexpensive batch fabrication of the components and flexibility in system design for application specific beam energies and currents. For prototyping the accelerator architecture, the components have been fabricated using the PCB. In this paper, we present proof of concept results of the principal components using the PCB: RF acceleration and ESQ focusing. Ongoing developments on implementing components in silicon and scaling of the accelerator technology to high currents and beam energies are discussed.

  13. Acceleration of the GAMESS-UK electronic structure package on graphical processing units.

    PubMed

    Wilkinson, Karl A; Sherwood, Paul; Guest, Martyn F; Naidoo, Kevin J

    2011-07-30

    The approach used to calculate the two-electron integral by many electronic structure packages including generalized atomic and molecular electronic structure system-UK has been designed for CPU-based compute units. We redesigned the two-electron compute algorithm for acceleration on a graphical processing unit (GPU). We report the acceleration strategy and illustrate it on the (ss|ss) type integrals. This strategy is general for Fortran-based codes and uses the Accelerator compiler from Portland Group International and GPU-based accelerators from Nvidia. The evaluation of (ss|ss) type integrals within calculations using Hartree Fock ab initio methods and density functional theory are accelerated by single and quad GPU hardware systems by factors of 43 and 153, respectively. The overall speedup for a single self consistent field cycle is at least a factor of eight times faster on a single GPU compared with that of a single CPU.

  14. H-mode accelerating structures with PMQ focusing for low-beta ion beams

    SciTech Connect

    Kurennoy, Sergey S; O' Hara, James F; Olivas, Eric R; Rybarcyk, Lawrence J

    2010-01-01

    We are developing high-efficiency normal-conducting RF accelerating structures based on inter-digital H-mode (IH) cavities and the transverse beam focusing with permanent-magnet quadrupoles (PMQ), for beam velocities in the range of a few percent of the speed of light. Such IH-PMQ accelerating structures following a short RFQ can be used in the front end of ion linacs or in stand-alone applications, e.g. a compact deuteron-beam accelerator up to the energy of several MeV. Results of combined 3-D modeling for a full IH-PMQ accelerator tank - electromagnetic computations, beam-dynamics simulations with high currents, and thermal-stress analysis - are presented. The accelerating field profile in the tank is tuned to provide the best beam propagation using coupled iterations of electromagnetic and beam-dynamics modeling. A cold model of the IH-PMQ tank is being manufactured.

  15. Technological Issues and High Gradient Test Results on X-Band Molybdenum Accelerating Structures

    SciTech Connect

    Spataro, B.; Alesini, D.; Chimenti, V.; Dolgashev, V.; Haase, A.; Tantawi, S.G.; Higashi, Y.; Marrelli, C.; Mostacci, A.; Parodi, R.; Yeremian, A.D.; /SLAC

    2012-04-24

    Two 11.424 GHz single cell standing wave accelerating structures have been fabricated for high gradient RF breakdown studies. Both are brazed structures: one made from copper and the other from sintered molybdenum bulk. The tests results are presented and compared to those of similar devices constructed at SLAC (Stanford Linear Accelerator Center) and KEK (Ko Enerugi Kasokuki Kenkyu Kiko). The technological issues to build both sections are discussed.

  16. Technological issues and high gradient test results on X-band molybdenum accelerating structures

    NASA Astrophysics Data System (ADS)

    Spataro, B.; Alesini, D.; Chimenti, V.; Dolgashev, V.; Haase, A.; Tantawi, S. G.; Higashi, Y.; Marrelli, C.; Mostacci, A.; Parodi, R.; Yeremian, A. D.

    2011-11-01

    Two 11.424 GHz single cell standing wave accelerating structures have been fabricated for high gradient RF breakdown studies. Both are brazed structures: one made from copper and the other from sintered molybdenum bulk. The tests results are presented and compared to those of similar devices constructed at SLAC ( Stanford Linear Accelerator Center) and KEK ( Kō Enerugī Kasokuki Kenkyū Kikō). The technological issues to build both sections are discussed.

  17. Analytical solutions for transient and steady state beam loading in arbitrary traveling wave accelerating structures

    SciTech Connect

    Lunin, A.; Yakovlev, V.; Grudiev, A.; /CERN

    2011-05-02

    Analytical solutions are derived for both transient and steady state gradient distributions in the traveling wave (TW) accelerating structures with arbitrary variation of parameters over the structure length. The results of the unloaded and beam loaded cases are presented. Finally, the exact analytical shape of the rf pulse waveform was found in order to apply the transient beam loading compensation scheme during the structure filling time. The obtained theoretical formulas were cross-checked by direct numerical simulations on the CLIC main linac accelerating structure and demonstrated a good agreement. The proposed methods provide a fast and reliable tool for the initial stage of the TW structure analysis.

  18. Theory of factors limiting high gradient operation of warm accelerating structures

    SciTech Connect

    Nusinovich, Gregory S.

    2014-07-22

    This report consists of two parts. In the first part we describe a study of the heating of microprotrusions on surfaces of accelerating structures. This ;process is believed to lead to breakdown in these structures. Our study revealed that for current accelerator parameters melting should not occur due to space charge limitations of the current emitted by a protrusion. The second part describes a novel concept to develop THz range sources based on harmonic cyclotron masers for driving future colliders. This work was stimulated by a recent request of SLAC to develop high power, high-efficiency sources of sub-THz radiation for future high-gradient accelerators.

  19. Experimental Studies of W-Band Accelerator Structures at High Field

    SciTech Connect

    Hill, Marc E

    2001-02-09

    A high-gradient electron accelerator is desired for high-energy physics research, where frequency scalings of breakdown and trapping of itinerant beamline particles dictates operation of the accelerator at short wavelengths. The first results of design and test of a high-gradient mm-wave linac with an operating frequency at 91.392 GHz (W-band) are presented. A novel approach to particle acceleration is presented employing a planar, dielectric lined waveguide used for particle acceleration. The traveling wave fields in the planar dielectric accelerator (PDA) are analyzed for an idealized structure, along with a circuit equivalent model used for understanding the structure as a microwave circuit. Along with the W-band accelerator structures, other components designed and tested are high power rf windows, high power attenuators, and a high power squeeze-type phase shifter. The design of the accelerator and its components where eased with the aide of numerical simulations using a finite-difference electromagnetic field solver. Manufacturing considerations of the small, delicate mm-wave components and the steps taken to reach a robust fabrication process are detailed. These devices were characterized under low power using a two-port vector network analyzer to verify tune and match, including measurements of the structures' fields using a bead-pull. The measurements are compared with theory throughout. Addition studies of the W-band structures were performed under high power utilizing a 11.424 GHz electron linac as a current source. Test results include W-band power levels of 200 kW, corresponding to fields in the PDA of over 20 MV/m, a higher gradient than any collider. Planar accelerator devices naturally have an rf quadrupole component of the accelerating field. Presented for the first time are the measurements of this effect.

  20. Studies of Breakdown in High Gradient X-Band Accelerator Structures Using Acoustic Emission

    SciTech Connect

    Frisch, Josef C

    2002-08-23

    X-band accelerator structures meeting the Next Linear Collider (NLC) design requirements have been found to suffer damage due to RF breakdown when processed to high gradients. Improved understanding of these breakdown events is desirable for the development of structure designs, fabrication procedures, and processing techniques that minimize structure damage [1]. Acoustic emission sensors attached to an accelerator structure can detect both nominal and breakdown RF pulses [2]. Using an array of acoustic sensors, we have been able to pinpoint both the cell and azimuth location of individual breakdown events. This allows studies of breakdown time and position sequences so that underlying causes can be determined. The technique provided a significant advance in studies of breakdown in the structure input coupler. In this paper we present acoustic emission sensor data and analysis from the breakdown studies in several x-band accelerator structures.

  1. A mm-wave planar microcavity structure for electron linear accelerator system

    SciTech Connect

    Kang, Y.W.; Kustom, R.; Mills, F.; Mavrogenes, G.; Henke, H.

    1993-07-01

    The muffin-tin cavity structure is planar and well suited for mm-wave accelerator with silicon etching techniques. A constant impedance traveling-wave structure is considered for design simplicity. The RF parameters are calculated and the shunt impedance is compared with the shunt impedance of a disk loaded cylindrical structure.

  2. Efficient low-beta H-mode accelerating structures with PMQ focusing

    SciTech Connect

    Kurennoy, Sergey S; O' Hara, James F; Olivas, Eric R; Rybarcyk, Lawrence J

    2008-01-01

    We are developing high-efficiency room-temperature RF accelerating structures for beam velocities in the range of a few percent of the speed of light by merging two well-known ideas: H-mode cavities and the transverse beam focusing with permanent-magnet quadrupoles (PMQ). Combining electromagnetic 3-D modeling with beam dynamics simulations and thermal-stress analysis, we have found that the H-mode structures with PMQ focusing provide a very efficient and practical accelerator for light-ion beams of considerable currents. Such accelerating structures following a short RFQ can be used in the front end of ion linacs or in stand-alone applications such as a compact deuteron-beam accelerator up to the energy of a few MeV.

  3. Summary Report on Working Group 5: Electromagnetic Structure-Based Acceleration

    NASA Astrophysics Data System (ADS)

    Power, John G.; Kimura, Wayne D.

    2002-12-01

    Recent progress and new developments in Electromagnetic Structure-Based Acceleration were presented in this Working Group (WG). The presentations made to the WG were separated into two categories: slow-wave and fast-wave accelerating structures. The slow-wave talks included a theoretical study of accelerators at optical frequencies that showed there are important and surprising differences between optical structures and traditional microwave accelerators. Practical issues for dielectric loaded accelerators were also addressed including a novel method for frequency tuning of dielectric structures and, in a joint session with the mm-wave sources WG, dielectric high power test results were presented. Theory and simulation results were presented for both laser-driven and beam-driven (i.e., wakefield) novel structures including cylindrical and planar dielectric devices and photonic band gap (PBG) devices including a scheme to mimic a plasma channel with a PBG. In the fast-wave talks, progress in developing highly-tapered inverse free electron lasers (IFEL), staging IFELs for monoenergetic laser acceleration, and generating attosecond electron pulses were presented. New designs and applications of cyclotron-based devices driven by laser or RF energy were also discussed.

  4. Particle Acceleration at Filamentary Structures Downstream of Collisionless Shocks in the Heliosphere.

    NASA Astrophysics Data System (ADS)

    Kucharek, H.; Pogorelov, N. V.; Gamayunov, K. V.

    2015-12-01

    Collisionless shocks are an important feature in astrophysical, heliospheric and magnetospheric settings. At these structures plasma is heated, the properties of flows are changed, and particles are accelerated to high energies. Particles are accelerated throughout the heliosphere. There are no times or conditions where suprathermal ions forming tails are not present on the solar wind ion distribution, and given the low speeds of these particles they must be accelerated locally in the heliosphere. Coronal mass ejections (CMEs) and co-rotating interaction regions (CIRs) accelerate particles up to 10s of MeV/nucleon. The termination shock of the solar and the heliosheath produce energetic particles including the Anomalous Cosmic Rays (ACRs), with energies in excess of 100 MeV. In the last few years' very interesting observations at low energies showing power laws that cannot be explained with commonly accepted acceleration mechanisms and thus increased the need for alternative acceleration processes. Fully consistent kinetic particle simulations such as hybrid simulations appear to be a powerful tool to investigated ion acceleration. Nowadays these simulations can be performed in 3D and relative large simulation domains covering up to hundreds of ion inertial length in size and thus representing the MHD scale. These 3D hybrid simulations show filamentary magnetic and density structures, which could be interpreted as small-scale flux ropes. The growth of these small-scale structures is also associated with ion acceleration. In this talk we will discuss properties of these filamentary structures, their spatial and temporal evolution and the particle dynamics during the acceleration process. The results of this study may be of particular importance for future high resolution magnetospheric and heliospheric mission such as THOR.

  5. Studies of Multipactor in Dielectric-Loaded Accelerator Structures: Comparison of Simulation Results with Experimental Data

    SciTech Connect

    Sinitsyn, Oleksandr; Nusinovich, Gregory; Antonsen, Thomas Jr.

    2010-11-04

    In this paper new results of numerical studies of multipactor in dielectric-loaded accelerator structures are presented. The results are compared with experimental data obtained during recent studies of such structures performed by Argonne National Laboratory, the Naval Research Laboratory, SLAC National Accelerator Laboratory and Euclid TechLabs, LLC. Good agreement between the theory and experiment was observed for the structures with larger inner diameter, however the structures with smaller inner diameter demonstrated a discrepancy between the two. Possible reasons for such discrepancy are discussed.

  6. Laser acceleration and deflection of 963 keV electrons with a silicon dielectric structure

    DOE PAGES

    Leedle, Kenneth J.; Pease, R. Fabian; Byer, Robert L.; ...

    2015-02-12

    Radio frequency particle accelerators are ubiquitous in ultrasmall and ultrafast science, but their size and cost have prompted exploration of compact and scalable alternatives such as the dielectric laser accelerator. We present the first demonstration, to the best of our knowledge, of high gradient laser acceleration and deflection of electrons with a silicon structure. Driven by a 5 nJ, 130 fs mode-locked Ti:sapphire laser at 907 nm wavelength, our devices achieve accelerating gradients in excess of 200 MeV/m and suboptical cycle streaking of 96.30 keV electrons. These results pave the way for high gradient silicon dielectric laser accelerators using commercialmore » lasers and subfemtosecond electron beam experiments.« less

  7. RF Processing of X-Band Accelerator Structures at the NLCTA

    SciTech Connect

    Adolphsen, Chris

    2000-08-24

    During the initial phase of operation, the linacs of the Next Linear Collider (NLC) will contain roughly 5,000 X-Band accelerator structures that will accelerate beams of electrons and positrons to 250 GeV. These structures will nominally operate at an unloaded gradient of 72 MV/m. As part of the NLC R and D program, several prototype structures have been built and operated at the Next Linear Collider Test Accelerator (NLCTA) at SLAC. Here, the effect of high gradient operation on the structure performance has been studied. Significant progress was made during the past year after the NLCTA power sources were upgraded to reliably produce the required NLC power levels and beyond. This paper describes the structures, the processing methodology and the observed effects of high gradient operation.

  8. Electron acceleration by femtosecond laser interaction with micro-structured plasmas

    NASA Astrophysics Data System (ADS)

    Goers, Andy James

    Laser-driven accelerators are a promising and compact alternative to RF accelerator technology for generating relativistic electron bunches for medical, scientific, and security applications. This dissertation presents three experiments using structured plasmas designed to advance the state of the art in laser-based electron accelerators, with the goal of reducing the energy of the drive laser pulse and enabling higher repetition rate operation with current laser technology. First, electron acceleration by intense femtosecond laser pulses in He-like nitrogen plasma waveguides is demonstrated. Second, significant progress toward a proof of concept realization of quasi-phasematched direct acceleration (QPM-DLA) is presented. Finally, a laser wakefield accelerator at very high plasma density is studied, enabling relativistic electron beam generation with ˜10 mJ pulse energies. Major results from these experiments include: • Acceleration of electrons up to 120 MeV from an ionization injected wakefield accelerator driven in a 1.5 mm long He-like nitrogen plasma waveguide • Guiding of an intense, quasi-radially polarized femtosecond laser pulse in a 1 cm plasma waveguide. This pulse provides a strong drive field for the QPM-DLA concept. • Wakefield acceleration of electrons up to ˜10 MeV with sub-terawatt, ˜10 mJ pulses interacting with a thin (˜200 mum), high density (>1020 cm-3) plasma. • Observation of an intense, coherent, broadband wave breaking radiation flash from a high plasma density laser wakefield accelerator. The flash radiates > 1% of the drive laser pulse energy in a bandwidth consistent with half-cycle (˜1 fs) emission from violent unidirectional acceleration of electron bunches from rest. These results open the way to high repetition rate (>˜kHz) laser-driven generation of relativistic electron beams with existing laser technology.

  9. On a theory of two-beam mechanisms of charged particle acceleration in electrodynamic structures

    SciTech Connect

    Ostrovsky, A.O.

    1993-09-01

    This work is devoted to the theoretical studies of two-beam mechanisms of charged particle acceleration in electronic structures. The first section continues the outline of results of theoretical studies commenced in the intermediate report and considers the two-beam scheme of acceleration in the plasma waveguide. According to this scheme the strong current relativistic electron beam (REB) excites the intensive plasma waves accelerating the electrons of the second beam. The driving beam is assumed to be density-modulated. The preliminary modulation of the driving REB is shown to enhance substantially the acceleration efficiency of relativistic electrons of the driven beam. The second section deals with the two-beam acceleration in the vacuum corrugated waveguide. According to this scheme the excitation of electromagnetic waves and acceleration of driven beam electrons by them is accomplished under different Cherenkov resonances between the particles of beams and the corrugated waveguide field. The electromagnetic field in the periodic structure is known to be the superposition of spatial harmonics. With the small depth of the periodic nonuniformity the amplitudes of these harmonics decrease fast with their number increasing. Therefore, if the driving beam is in the Cherenkov resonance with the first spatial harmonic and the driven beam is in resonance with the zero space harmonic then the force accelerating the driven beam would be considerably bigger than the force decelerating the driving beam electrons.

  10. Particle Acceleration: From Galaxies to Large Scale Structure

    SciTech Connect

    Biermann, Peter L.; Bisnovatyi-Kogan, Gennady; Moiseenko, Sergej

    2005-09-28

    In this brief review we discuss current efforts to understand the origin of energetic particles, focussing here on the recent work on the physics of supernova explosions. Acceleration to the highest energy may come from jets and hot spots emanating from massive black holes. If the sky remains smooth in the arrival directions of ultrahigh energy cosmic rays to the highest energies, then we need new sources, and one extreme speculation would be to invoke Lorentz Invariance Violation, with proton decay, neutron survival, and no strong photomeson interaction to higher energy. For the Galactic cosmic rays explosions of red supergiant stars and Wolf Rayet stars may provide much of the cosmic rays. This is intimately connected with the physics of their explosion, and implies that the magneto-rotational mechanism is the main one chosen by Nature. This offers a consistent picture for the X-ray fans of Cas A, and gamma ray bursts. Each of these concepts leads to clear predictions. It will be quite an achievement to prove this or any other proposal -- none is without difficulties. We do have potentially a full theory to account for cosmic rays at all energies; crucial tests will be performed with the current new instruments.

  11. An Update on the DOE Early Career Project on Photonic Band Gap Accelerator Structures

    SciTech Connect

    Simakov, Evgenya I.; Edwards, Randall L.; Haynes, William B.; Madrid, Michael A.; Romero, Frank P.; Tajima, Tsuyoshi; Tuzel, Walter M.; Boulware , Chase H.; Grimm, Terry

    2012-06-07

    We performed fabrication of two SRF PBG resonators at 2.1 GHz and demonstrated their proof-of-principle operation at high gradients. Measured characteristics of the resonators were in good agreement with theoretical predictions. We demonstrated that SRF PBG cavities can be operated at 15 MV/m accelerating gradients. We completed the design and started fabrication of the 16-cell PBG accelerating structure at 11.7 GHz for wakefield testing at AWA.

  12. Summary Report of Working Group 7: Electromagnetic-Structure Based Accelerators

    SciTech Connect

    Colby, E.; Musumeci, P.; /INFN, Rome

    2007-04-02

    We detail the most pressing physics and technical issues confronting short-wavelength acceleration. We review new acceleration concepts that are proposed and under development, and recent progress on technical issues such as structure fabrication and material damage. We outline key areas where work is still needed before a reliable assessment of the value of working at wavelengths below 1 cm can be made. Possible ways to enhance collaboration and progress in this important area are also discussed.

  13. Design and fabrication of a traveling-wave muffin-tin accelerating structure at 90 GHz

    SciTech Connect

    Chou, P.J.; Bowden, G.B.; Copeland, M.R.; Menegat, A.; Siemann, R.H.; Henke, H.

    1997-05-01

    A prototype of a muffin-tin accelerating structure operating at 32 times the SLAC frequency (2.856 GHz) was built for research in high gradient acceleration. A traveling-wave design with single input and output feeds was chosen for the prototype which was fabricated by wire electrodischarge machining. Features of the mechanical design for the prototype are described. Design improvements are presented including considerations of cooling and vacuum.

  14. Proposed Few-optical Cycle Laser-driven ParticleAccelerator Structure

    SciTech Connect

    Plettner, T.; Lu, P.; Byer, R.L.; /Stanford U., Ginzton Lab.

    2006-10-06

    We describe a transparent dielectric grating accelerator structure that is designed for ultra-short laser pulse operation. The structure is based on the principle of periodic field reversal to achieve phase synchronicity for relativistic particles, however to preserve ultra-short pulse operation it does not resonate the laser field in the vacuum channel. The geometry of the structure appears well suited for application with high average power lasers and high thermal loading. Finally, it shows potential for an unloaded gradient of 10 GeV/m with 10 fsec laser pulses and the possibility to accelerate 10{sup 6} electrons per bunch at an efficiency of 8%. The fabrication procedure and a proposed near term experiment with this accelerator structure are presented.

  15. CPU-GPU hybrid accelerating the Zuker algorithm for RNA secondary structure prediction applications

    PubMed Central

    2012-01-01

    Background Prediction of ribonucleic acid (RNA) secondary structure remains one of the most important research areas in bioinformatics. The Zuker algorithm is one of the most popular methods of free energy minimization for RNA secondary structure prediction. Thus far, few studies have been reported on the acceleration of the Zuker algorithm on general-purpose processors or on extra accelerators such as Field Programmable Gate-Array (FPGA) and Graphics Processing Units (GPU). To the best of our knowledge, no implementation combines both CPU and extra accelerators, such as GPUs, to accelerate the Zuker algorithm applications. Results In this paper, a CPU-GPU hybrid computing system that accelerates Zuker algorithm applications for RNA secondary structure prediction is proposed. The computing tasks are allocated between CPU and GPU for parallel cooperate execution. Performance differences between the CPU and the GPU in the task-allocation scheme are considered to obtain workload balance. To improve the hybrid system performance, the Zuker algorithm is optimally implemented with special methods for CPU and GPU architecture. Conclusions Speedup of 15.93× over optimized multi-core SIMD CPU implementation and performance advantage of 16% over optimized GPU implementation are shown in the experimental results. More than 14% of the sequences are executed on CPU in the hybrid system. The system combining CPU and GPU to accelerate the Zuker algorithm is proven to be promising and can be applied to other bioinformatics applications. PMID:22369626

  16. CPU-GPU hybrid accelerating the Zuker algorithm for RNA secondary structure prediction applications.

    PubMed

    Lei, Guoqing; Dou, Yong; Wan, Wen; Xia, Fei; Li, Rongchun; Ma, Meng; Zou, Dan

    2012-01-01

    Prediction of ribonucleic acid (RNA) secondary structure remains one of the most important research areas in bioinformatics. The Zuker algorithm is one of the most popular methods of free energy minimization for RNA secondary structure prediction. Thus far, few studies have been reported on the acceleration of the Zuker algorithm on general-purpose processors or on extra accelerators such as Field Programmable Gate-Array (FPGA) and Graphics Processing Units (GPU). To the best of our knowledge, no implementation combines both CPU and extra accelerators, such as GPUs, to accelerate the Zuker algorithm applications. In this paper, a CPU-GPU hybrid computing system that accelerates Zuker algorithm applications for RNA secondary structure prediction is proposed. The computing tasks are allocated between CPU and GPU for parallel cooperate execution. Performance differences between the CPU and the GPU in the task-allocation scheme are considered to obtain workload balance. To improve the hybrid system performance, the Zuker algorithm is optimally implemented with special methods for CPU and GPU architecture. Speedup of 15.93× over optimized multi-core SIMD CPU implementation and performance advantage of 16% over optimized GPU implementation are shown in the experimental results. More than 14% of the sequences are executed on CPU in the hybrid system. The system combining CPU and GPU to accelerate the Zuker algorithm is proven to be promising and can be applied to other bioinformatics applications.

  17. Design of RF Feed System for Standing-Wave Accelerator Structures

    SciTech Connect

    Neilson, Jeffrey; Tantawi, Sami; Dolgashev, Valery

    2010-11-04

    We are investigating a standing wave structure with an rf feed to each individual cell. This approach minimizes rf power flow and electromagnetic energy absorbed by an rf breakdown. The objective of this work is a robust high-gradient (above 100 MV/m) X-band accelerator structure.

  18. Frequency Domain Tomography Of Evolving Laser-Plasma Accelerator Structures

    SciTech Connect

    Dong Peng; Reed, Stephen; Kalmykov, Serguei; Shvets, Gennady; Downer, Mike

    2009-01-22

    Frequency Domain Holography (FDH), a technique for visualizing quasistatic objects propagating near the speed of light, has produced 'snapshots' of laser wakefields, but they are averaged over structural variations that occur during propagation through the plasma medium. Here we explore via simulations a generalization of FDH--that we call Frequency Domain Tomography (FDT)--that can potentially record a time sequence of quasistatic snapshots, like the frames of a movie, of the wake structure as it propagates through the plasma. FDT utilizes a several probe-reference pulse pairs that propagate obliquely to the drive pulse and wakefield, along with tomographic reconstruction algorithms similar to those used in medical CAT scans.

  19. Update on the Development of Externally Powered Dielectric-Loaded Accelerating Structures

    SciTech Connect

    Jing, C.; Kanareykin, A.; Gai, W.; Konecny, R.; Power, J. G.; Liu, W.; Gold, S. H.; Kinkead, A. K.

    2009-01-22

    We report on recent progress in a program to develop an RF-driven Dielectric-Loaded Accelerating (DLA) structure, capable of supporting high gradient acceleration. Previous high power tests revealed that the earlier DLA structures suffered from multipactor and arcing at the dielectric joint. A few new DLA structures have been designed to alleviate this limitation including the coaxial coupler based DLA structure and the clamped DLA structure. These structures were recently fabricated and high power tested at the NRL X-band Magnicon facility. Results show the multipactor can be reduced by the TiN coating on the dielectric surface. Gradient of 15 MV/m has also been tested without dielectric breakdown in the test of the clamped DLA structure. Detailed results are reported, and future plans discussed.

  20. Update on the development of externally powered dielectric-loaded accelerating structures.

    SciTech Connect

    Jing, C.; Gai, W.; Konecny, R.; Power, J. G.; Liu, W.; Kanareykin, A.; Gold, S.; Kinkead, A. K.; High Energy Physics; EuclidTechlabs,; Naval Research Lab.; Icarus Research

    2009-01-01

    We report on recent progress in a program to develop an RF-driven Dielectric-Loaded Accelerating (DLA) structure, capable of supporting high gradient acceleration. Previous high power tests revealed that the earlier DLA structures suffered from multipactor and arcing at the dielectric joint. A few new DLA structures have been designed to alleviate this limitation including the coaxial coupler based DLA structure and the clamped DLA structure. These structures were recently fabricated and high power tested at the NRL X-band Magnicon facility. Results show the multipactor can be reduced by the TiN coating on the dielectric surface. Gradient of 15 MV/m has also been tested without dielectric breakdown in the test of the clamped DLA structure. Detailed results are reported, and future plans discussed.

  1. Active vibration suppression through positive acceleration feedback on a building-like structure: An experimental study

    NASA Astrophysics Data System (ADS)

    Enríquez-Zárate, J.; Silva-Navarro, G.; Abundis-Fong, H. F.

    2016-05-01

    This work deals with the structural and dynamic analysis of a building-like structure consisting of a three-story building with one active vibration absorber. The base of the structure is perturbed using an electromagnetic shaker, which provides forces with a wide range of excitation frequencies, including some resonance frequencies of the structure. One beam-column of the structure is coupled with a PZT stack actuator to reduce the vibrations. The overall mechanical structure is modeled using Euler-Lagrange methodology and validated using experimental modal analysis and Fine Element Method (FEM) techniques. The active control laws are synthesized to actively attenuate the vibration system response via the PZT stack actuator, caused by excitation forces acting on the base of the structure. The control scheme is obtained using Positive Acceleration Feedback (PAF) and Multiple Positive Acceleration Feedback (MPAF) to improve the closed-loop system response. Some experimental results are included to illustrate the overall system performance.

  2. Accelerated life assessment of coating on the radar structure components in coastal environment.

    PubMed

    Liu, Zhe; Ming, ZhiMao

    2016-07-04

    This paper aimed to build an accelerated life test scheme and carry out quantitative analysis between accelerated life test in the laboratory and actual service for the coating composed of epoxy primer and polyurethane paint on structure components of some kind of radar served in the coastal environment of South China Sea. The accelerated life test scheme was built based on the service environment and failure analysis of the coating. The quantitative analysis between accelerated life test and actual service was conducted by comparing the gloss loss, discoloration, chalking, blistering, cracking and electrochemical impedance spectroscopy of the coating. The main factors leading to the coating failure were ultraviolet radiation, temperature, moisture, salt fog and loads, the accelerated life test included ultraviolet radiation, damp heat, thermal shock, fatigue and salt spray. The quantitative relationship was that one cycle of the accelerated life test was equal to actual service for one year. It was established that one cycle of the accelerated life test was equal to actual service for one year. It provided a precise way to predict actual service life of newly developed coatings for the manufacturer.

  3. Field analysis of a dielectric-loaded rectangular waveguide accelerating structure.

    SciTech Connect

    Xiao, L.; Gai, W.; Sun, X.

    2001-07-16

    In this paper, we present a detailed analysis of the modes of a dielectric-loaded rectangular waveguide accelerating structure. In general, the acceleration field in a synchronous acceleration mode is non-uniform in the two transverse dimensions. However, we could use an array of these structures rotated alternatively by 90 degrees to get a focusing-defocusing force continuously as a simple FODO lattice, while maintaining uniform energy gain. The expressions of characteristic parameters such as R/Q, group velocity and attenuation constant are given. The longitudinal wake field experienced by a relativistic charged particle beam in the structure is also presented. These analytical results are also compared with numerical calculations using the MAFIA code suite demonstrating the validity of our analytic approach.

  4. Challenges to self-acceleration in modified gravity from gravitational waves and large-scale structure

    NASA Astrophysics Data System (ADS)

    Lombriser, Lucas; Lima, Nelson A.

    2017-02-01

    With the advent of gravitational-wave astronomy marked by the aLIGO GW150914 and GW151226 observations, a measurement of the cosmological speed of gravity will likely soon be realised. We show that a confirmation of equality to the speed of light as indicated by indirect Galactic observations will have important consequences for a very large class of alternative explanations of the late-time accelerated expansion of our Universe. It will break the dark degeneracy of self-accelerated Horndeski scalar-tensor theories in the large-scale structure that currently limits a rigorous discrimination between acceleration from modified gravity and from a cosmological constant or dark energy. Signatures of a self-acceleration must then manifest in the linear, unscreened cosmological structure. We describe the minimal modification required for self-acceleration with standard gravitational-wave speed and show that its maximum likelihood yields a 3σ poorer fit to cosmological observations compared to a cosmological constant. Hence, equality between the speeds challenges the concept of cosmic acceleration from a genuine scalar-tensor modification of gravity.

  5. Enhancement of maximum attainable ion energy in the radiation pressure acceleration regime using a guiding structure

    DOE PAGES

    Bulanov, S. S.; Esarey, E.; Schroeder, C. B.; ...

    2015-03-13

    Radiation Pressure Acceleration is a highly efficient mechanism of laser driven ion acceleration, with the laser energy almost totally transferrable to the ions in the relativistic regime. There is a fundamental limit on the maximum attainable ion energy, which is determined by the group velocity of the laser. In the case of a tightly focused laser pulses, which are utilized to get the highest intensity, another factor limiting the maximum ion energy comes into play, the transverse expansion of the target. Transverse expansion makes the target transparent for radiation, thus reducing the effectiveness of acceleration. Utilization of an external guidingmore » structure for the accelerating laser pulse may provide a way of compensating for the group velocity and transverse expansion effects.« less

  6. Enhancement of maximum attainable ion energy in the radiation pressure acceleration regime using a guiding structure

    SciTech Connect

    Bulanov, S. S.; Esarey, E.; Schroeder, C. B.; Bulanov, S. V.; Esirkepov, T. Zh.; Kando, M.; Pegoraro, F.; Leemans, W. P.

    2015-03-13

    Radiation Pressure Acceleration is a highly efficient mechanism of laser driven ion acceleration, with the laser energy almost totally transferrable to the ions in the relativistic regime. There is a fundamental limit on the maximum attainable ion energy, which is determined by the group velocity of the laser. In the case of a tightly focused laser pulses, which are utilized to get the highest intensity, another factor limiting the maximum ion energy comes into play, the transverse expansion of the target. Transverse expansion makes the target transparent for radiation, thus reducing the effectiveness of acceleration. Utilization of an external guiding structure for the accelerating laser pulse may provide a way of compensating for the group velocity and transverse expansion effects.

  7. Self-mapping the longitudinal field structure of a nonlinear plasma accelerator cavity

    NASA Astrophysics Data System (ADS)

    Clayton, C. E.; Adli, E.; Allen, J.; An, W.; Clarke, C. I.; Corde, S.; Frederico, J.; Gessner, S.; Green, S. Z.; Hogan, M. J.; Joshi, C.; Litos, M.; Lu, W.; Marsh, K. A.; Mori, W. B.; Vafaei-Najafabadi, N.; Xu, X.; Yakimenko, V.

    2016-08-01

    The preservation of emittance of the accelerating beam is the next challenge for plasma-based accelerators envisioned for future light sources and colliders. The field structure of a highly nonlinear plasma wake is potentially suitable for this purpose but has not been yet measured. Here we show that the longitudinal variation of the fields in a nonlinear plasma wakefield accelerator cavity produced by a relativistic electron bunch can be mapped using the bunch itself as a probe. We find that, for much of the cavity that is devoid of plasma electrons, the transverse force is constant longitudinally to within +/-3% (r.m.s.). Moreover, comparison of experimental data and simulations has resulted in mapping of the longitudinal electric field of the unloaded wake up to 83 GV m-1 to a similar degree of accuracy. These results bode well for high-gradient, high-efficiency acceleration of electron bunches while preserving their emittance in such a cavity.

  8. Latest Development in Superconducting RF Structures for beta=1 Particle Acceleration

    SciTech Connect

    Peter Kneisel

    2006-06-26

    Superconducting RF technology is since nearly a decade routinely applied to different kinds of accelerating devices: linear accelerators, storage rings, synchrotron light sources and FEL's. With the technology recommendation for the International Linear Collider (ILC) a year ago, new emphasis has been placed on improving the performance of accelerating cavities both in Q-value and in accelerating gradients with the goal to achieve performance levels close to the fundamental limits given by the material parameters of the choice material, niobium. This paper will summarize the challenges to SRF technology and will review the latest developments in superconducting structure design. Additionally, it will give an overview of the newest results and will report on the developments in alternative materials and technologies.

  9. USE OF ACOUSTIC EMISSION TO DIAGNOSE BREAKDOWN IN ACCELERATOR RF STRUCTURES

    SciTech Connect

    Nelson, Janice L.

    2003-05-12

    Accelerator structures of a wide variety have been damaged by RF breakdowns. Very little is known about the mechanisms that cause the breakdown and the damage although there has been theoretical work [1,2]. Using an array of ultrasonic acoustic emission sensors we have been able to locate and classify breakdown events more accurately than possible using microwave techniques. Data from the technique has led to improvements in the design of the NLC X-band RF structure. We report results of acoustic emission studies at the DESY TESLA Test Facility and the SLAC NLC Test Accelerator.

  10. Experimental measurements of rf breakdowns and deflecting gradients in mm-wave metallic accelerating structures

    DOE PAGES

    Dal Forno, Massimo; Dolgashev, Valery; Bowden, Gordon; ...

    2016-05-03

    We present an experimental study of a high-gradient metallic accelerating structure at sub-THz frequencies, where we investigated the physics of rf breakdowns. Wakefields in the structure were excited by an ultrarelativistic electron beam. We present the first quantitative measurements of gradients and metal vacuum rf breakdowns in sub-THz accelerating cavities. When the beam travels off axis, a deflecting field is induced in addition to the longitudinal field. We measured the deflecting forces by observing the displacement and changes in the shape of the electron bunch. This behavior can be exploited for subfemtosecond beam diagnostics.

  11. Using Machine Learning to Accelerate Complex Atomic Structure Elucidation

    NASA Astrophysics Data System (ADS)

    Brouwer, William; Calderin, Lazaro; Sofo, Jorge

    2012-02-01

    Workers in various scientific disciplines seek to develop chemical models for extended and molecular systems. The modeling process revolves around the gradual refinement of model assumptions, through comparison of experimental and computational results. Solid state Nuclear Magnetic Resonance (NMR) is one such experimental technique, providing great insight into chemical order over Angstrom length scales. However, interpretation of spectra for complex materials is difficult, often requiring intensive simulations. Similarly, working forward from the model in order to produce experimental quantities via ab initio is computationally demanding. The work involved in these two significant steps, compounded by the need to iterate back and forth, drastically slows the discovery process for new materials. There is thus great motivation for the derivation of structural models directly from complex experimental data, the subject of this work. Using solid state NMR experimental datasets, in conjunction with ab initio calculations of measurable NMR parameters, a network of machine learning kernels are trained to rapidly yield structural details, on the basis of input NMR spectra. Results for an environmentally relevant material will be presented, and directions for future work.

  12. Comparison of accelerating structures for the first cavity of the main part of the INR linac

    NASA Astrophysics Data System (ADS)

    Rybakov, I. V.; Kalinin, Y. Z.; Leontev, V. N.; Naboka, A. N.; Paramonov, V. V.; Serov, V. L.; Feschenko, A. V.

    2016-09-01

    For the beam power improvement of the hydrogen-ion INR linac replacement of the first four-section cavity in the main part of linac is required. Existent cavity is realized using DAW structure on 991 MHz operating frequency. The new cavity should at least not lose in parameters to the current structure and essential changes in other linac systems are not wish able. Parameters of accelerating structures possible for such application are compared.

  13. Cosmic microwave background anisotropy from nonlinear structures in accelerating universes

    SciTech Connect

    Sakai, Nobuyuki; Inoue, Kaiki Taro

    2008-09-15

    We study the cosmic microwave background (CMB) anisotropy due to spherically symmetric nonlinear structures in flat universes with dust and a cosmological constant. By modeling a time-evolving spherical compensated void/lump by Lemaitre-Tolman-Bondi spacetimes, we numerically solve the null geodesic equations with the Einstein equations. We find that a nonlinear void redshifts the CMB photons that pass through it regardless of the distance to it. In contrast, a nonlinear lump blueshifts (or redshifts) the CMB photons if it is located near (or sufficiently far from) us. The present analysis comprehensively covers previous works based on a thin-shell approximation and a linear/second-order perturbation method and the effects of shell thickness and full nonlinearity. Our results indicate that, if quasilinear and large (> or approx.100 Mpc) voids/lumps would exist, they could be observed as cold or hot spots with temperature variance > or approx. 10{sup -5} K in the CMB sky.

  14. A linear accelerator power amplification system for high gradient structure research

    SciTech Connect

    Haimson, J.; Mecklenburg, B.

    1999-07-12

    The ongoing development of linear collider high power RF sources and pulse compression systems has resulted in substantial progress towards a goal of providing a peak RF power level of approximately 250 MW at the input of the accelerator structure. While the immediate development and the high power testing of specialized waveguide components required for power transmission at these high levels have proceeded expeditiously due to the availability of resonant ring systems, the testing of high gradient accelerator structures at very high power levels, and the investigation of coupler cavity RF breakdown problems have, typically, been curtailed due to the unavailability of suitable 200 to 300 MW RF test facilities. We describe herein a compact, high peak power amplification system based on a dual hybrid bridge configuration that avoids the need for power splitters at the accelerator dual feed couplers, and also provides a convenient interface for installing high gradient accelerator test structures. Design parameters are presented for a proposed power amplification system that makes use of a 75 MW, 1/2 {mu}s flat-top RF source to produce 280 MW, 1/4 {mu}s flat-top power for testing dual feed TW experimental accelerator sections.

  15. A linear accelerator power amplification system for high gradient structure research

    SciTech Connect

    Haimson, J.; Mecklenburg, B.

    1999-07-01

    The ongoing development of linear collider high power RF sources and pulse compression systems has resulted in substantial progress towards a goal of providing a peak RF power level of approximately 250 MW at the input of the accelerator structure. While the immediate development and the high power testing of specialized waveguide components required for power transmission at these high levels have proceeded expeditiously due to the availability of resonant ring systems, the testing of high gradient accelerator structures at very high power levels, and the investigation of coupler cavity RF breakdown problems have, typically, been curtailed due to the unavailability of suitable 200 to 300 MW RF test facilities. We describe herein a compact, high peak power amplification system based on a dual hybrid bridge configuration that avoids the need for power splitters at the accelerator dual feed couplers, and also provides a convenient interface for installing high gradient accelerator test structures. Design parameters are presented for a proposed power amplification system that makes use of a 75 MW, 1/2 {mu}s flat-top RF source to produce 280 MW, 1/4 {mu}s flat-top power for testing dual feed TW experimental accelerator sections. {copyright} {ital 1999 American Institute of Physics.}

  16. Comparison of accelerated T1-weighted whole-brain structural-imaging protocols.

    PubMed

    Falkovskiy, Pavel; Brenner, Daniel; Feiweier, Thorsten; Kannengiesser, Stephan; Maréchal, Bénédicte; Kober, Tobias; Roche, Alexis; Thostenson, Kaely; Meuli, Reto; Reyes, Denise; Stoecker, Tony; Bernstein, Matt A; Thiran, Jean-Philippe; Krueger, Gunnar

    2016-01-01

    Imaging in neuroscience, clinical research and pharmaceutical trials often employs the 3D magnetisation-prepared rapid gradient-echo (MPRAGE) sequence to obtain structural T1-weighted images with high spatial resolution of the human brain. Typical research and clinical routine MPRAGE protocols with ~1mm isotropic resolution require data acquisition time in the range of 5-10min and often use only moderate two-fold acceleration factor for parallel imaging. Recent advances in MRI hardware and acquisition methodology promise improved leverage of the MR signal and more benign artefact properties in particular when employing increased acceleration factors in clinical routine and research. In this study, we examined four variants of a four-fold-accelerated MPRAGE protocol (2D-GRAPPA, CAIPIRINHA, CAIPIRINHA elliptical, and segmented MPRAGE) and compared clinical readings, basic image quality metrics (SNR, CNR), and automated brain tissue segmentation for morphological assessments of brain structures. The results were benchmarked against a widely-used two-fold-accelerated 3T ADNI MPRAGE protocol that served as reference in this study. 22 healthy subjects (age=20-44yrs.) were imaged with all MPRAGE variants in a single session. An experienced reader rated all images of clinically useful image quality. CAIPIRINHA MPRAGE scans were perceived on average to be of identical value for reading as the reference ADNI-2 protocol. SNR and CNR measurements exhibited the theoretically expected performance at the four-fold acceleration. The results of this study demonstrate that the four-fold accelerated protocols introduce systematic biases in the segmentation results of some brain structures compared to the reference ADNI-2 protocol. Furthermore, results suggest that the increased noise levels in the accelerated protocols play an important role in introducing these biases, at least under the present study conditions. Copyright © 2015 Elsevier Inc. All rights reserved.

  17. Development of low-loss cryo-accelerating structure with high-purity copper

    NASA Astrophysics Data System (ADS)

    Iino, Akihiro; Yamaguchi, Seiya; Shintomi, Takakazu; Higo, Toshiyasu; Funahashi, Yoshisato; Matsumoto, Shuji; Michizono, Shinichiro; Ueno, Kenji; Endo, Katsumi

    2017-09-01

    In this paper, the development of an accelerating structure with high-purity copper operated at approximately 20 K is described. The aim is to obtain a dramatic increase in the quality factor (Q factor), which is an important parameter as regards enhancement of the acceleration gradient in a normal-conducting accelerating structure that has been operated at room temperature in the past. First, the Q factors of pillbox cavities comprised of two types of copper with different purities (99.99% and 99.99998%) were measured, at room temperature (300 K) and at a relatively low temperature (20 K); the resultant ratios, Q0(20 K)/Q0(300 K), were then compared with calculated values. Hence, it was found that the experimental and calculated values agree to within several percent, and converge to a constant value (approximately 5.3) when the residual resistance ratio is above 500. Next, a C-band accelerating structure was fabricated using a copper material having a purity of 99.99998%, and high-power testing of the structure was conducted at 20 K. Hence, it was found that the accelerating gradient Eacc reaches 30.9 MV/m with a 1.0-μs pulse width and 50-Hz repetition rate. In the high-power test, it was revealed that the radiation dose rate for C-band structure (20 K) was about two orders of magnitude lower than that for S-band structure (303 K) under the same conditions. Further, the magnitude of the dark current generated in this structure was estimated to be several femtoamps, which was below the detection limit. This finding was based on the assumption that the dark current magnitude is proportional to the radiation dose; however, no dark current was observed.

  18. Capturing Structural Dynamics in Crystalline Silicon Using Chirped Electrons from a Laser Wakefield Accelerator.

    PubMed

    He, Z-H; Beaurepaire, B; Nees, J A; Gallé, G; Scott, S A; Pérez, J R Sánchez; Lagally, M G; Krushelnick, K; Thomas, A G R; Faure, J

    2016-11-08

    Recent progress in laser wakefield acceleration has led to the emergence of a new generation of electron and X-ray sources that may have enormous benefits for ultrafast science. These novel sources promise to become indispensable tools for the investigation of structural dynamics on the femtosecond time scale, with spatial resolution on the atomic scale. Here, we demonstrate the use of laser-wakefield-accelerated electron bunches for time-resolved electron diffraction measurements of the structural dynamics of single-crystal silicon nano-membranes pumped by an ultrafast laser pulse. In our proof-of-concept study, we resolve the silicon lattice dynamics on a picosecond time scale by deflecting the momentum-time correlated electrons in the diffraction peaks with a static magnetic field to obtain the time-dependent diffraction efficiency. Further improvements may lead to femtosecond temporal resolution, with negligible pump-probe jitter being possible with future laser-wakefield-accelerator ultrafast-electron-diffraction schemes.

  19. Studies of Room Temperature Accelerator Structures for the ILC Positron Source

    SciTech Connect

    Wang, J.W.; Adolphsen, C.; Bharadwaj, V.; Bowden, G.B.; Dolgashev, V.A.; Jones, R.M.; Jongewaard, E.N.; Lewandowski, J.R.; Li, Z.; Miller, R.H.; /SLAC

    2006-03-15

    There are many challenges in the design of the normal-conducting portion of the ILC positron injector system such as achieving adequate cooling with the high RF and particle loss heating, and sustaining high accelerator gradients during millisecond-long pulses in a strong magnetic field. The proposed design for the positron injector contains both standing-wave and traveling-wave L-band accelerator structures for high RF efficiency, low cost and ease of fabrication. This paper presents results from several studies including particle energy deposition for both undulator based and conventional positron sources, cooling system design, accelerator structure optimization, RF pulse heating, cavity frequency stabilization, and RF feed system design.

  20. Free-electron laser as a power source for a high-gradient accelerating structure

    SciTech Connect

    Sessler, A.M.

    1982-02-01

    A two beam colliding linac accelerator is proposed in which one beam is intense (approx. = 1KA), of low energy (approx. = MeV), and long (approx. = 100 ns) and provides power at 1 cm wavelength through a free-electron-laser-mechanism to the second beam of a few electrons (approx. = 10/sup 11/), which gain energy at the rate of 250 MeV/m in a high-gradient accelerating structure and hence reach 375 GeV in 1.5 km. The intense beam is given energy by induction units and gains, and losses by radiation, 250 keV/m thus supplying 25 J/m to the accelerating structure. The luminosity, L, of two such linacs would be, at a repetition rate of 1 kHz, L = 4. x 10/sup 32/ cm/sup -2/ s/sup -1/.

  1. Capturing Structural Dynamics in Crystalline Silicon Using Chirped Electrons from a Laser Wakefield Accelerator

    NASA Astrophysics Data System (ADS)

    He, Z.-H.; Beaurepaire, B.; Nees, J. A.; Gallé, G.; Scott, S. A.; Pérez, J. R. Sánchez; Lagally, M. G.; Krushelnick, K.; Thomas, A. G. R.; Faure, J.

    2016-11-01

    Recent progress in laser wakefield acceleration has led to the emergence of a new generation of electron and X-ray sources that may have enormous benefits for ultrafast science. These novel sources promise to become indispensable tools for the investigation of structural dynamics on the femtosecond time scale, with spatial resolution on the atomic scale. Here, we demonstrate the use of laser-wakefield-accelerated electron bunches for time-resolved electron diffraction measurements of the structural dynamics of single-crystal silicon nano-membranes pumped by an ultrafast laser pulse. In our proof-of-concept study, we resolve the silicon lattice dynamics on a picosecond time scale by deflecting the momentum-time correlated electrons in the diffraction peaks with a static magnetic field to obtain the time-dependent diffraction efficiency. Further improvements may lead to femtosecond temporal resolution, with negligible pump-probe jitter being possible with future laser-wakefield-accelerator ultrafast-electron-diffraction schemes.

  2. Future accelerators (?)

    SciTech Connect

    John Womersley

    2003-08-21

    I describe the future accelerator facilities that are currently foreseen for electroweak scale physics, neutrino physics, and nuclear structure. I will explore the physics justification for these machines, and suggest how the case for future accelerators can be made.

  3. Observation of multipactor suppression in a dielectric-loaded accelerating structure using an applied axial magnetic field

    SciTech Connect

    Jing, C.; Konecny, R.; Antipov, S.; Chang, C.; Gold, S. H.; Schoessow, P.; Kanareykin, A.; Gai, W.

    2013-11-18

    Efforts by a number of institutions to develop a Dielectric-Loaded Accelerating (DLA) structure capable of supporting high gradient acceleration when driven by an external radio frequency source have been ongoing over the past decade. Single surface resonant multipactor has been previously identified as one of the major limitations on the practical application of DLA structures in electron accelerators. In this paper, we report the results of an experiment that demonstrated suppression of multipactor growth in an X-band DLA structure through the use of an applied axial magnetic field. This represents an advance toward the practical use of DLA structures in many accelerator applications.

  4. International X-Band Linear Collider Accelerator Structure R&D

    SciTech Connect

    Wang, J.W.; /SLAC

    2009-03-04

    For more than fifteen years before the International Technology Recommendation Panel (ITRP) decision in August, 2004, there were intensive R&D activities and broad international collaboration among the groups at SLAC, KEK, FNAL, LLNL and other labs for the room temperature X-Band accelerator structures. The goal was to provide an optimized design of the main linac structure for the NLC (Next Linear Collider) or GLC (Global Linear Collider). There have been two major challenges in developing X-band accelerator structures for the linear colliders. The first is to demonstrate stable, long-term operation at the high gradient (65 MV/m) that is required to optimize the machine cost. The second is to strongly suppress the beam induced long-range wakefields, which is required to achieve high luminosity. More than thirty X-band accelerator structures with various RF parameters, cavity shapes and coupler types have been fabricated and tested since 1989. A summary of the main achievements and experiences are presented in this talk including the structure design, manufacturing techniques, high power performance, and other structure related issues. Also, the new progress in collaborating with the CLIC, high gradient structures and X-Band structure applications for RF deflectors and others are briefly introduced.

  5. X-Band Photonic Band-Gap Accelerator Structure Breakdown Experiment

    SciTech Connect

    Marsh, Roark A.; Shapiro, Michael A.; Temkin, Richard J.; Dolgashev, Valery A.; Laurent, Lisa L.; Lewandowski, James R.; Yeremian, A.Dian; Tantawi, Sami G.; /SLAC

    2012-06-11

    In order to understand the performance of photonic band-gap (PBG) structures under realistic high gradient, high power, high repetition rate operation, a PBG accelerator structure was designed and tested at X band (11.424 GHz). The structure consisted of a single test cell with matching cells before and after the structure. The design followed principles previously established in testing a series of conventional pillbox structures. The PBG structure was tested at an accelerating gradient of 65 MV/m yielding a breakdown rate of two breakdowns per hour at 60 Hz. An accelerating gradient above 110 MV/m was demonstrated at a higher breakdown rate. Significant pulsed heating occurred on the surface of the inner rods of the PBG structure, with a temperature rise of 85 K estimated when operating in 100 ns pulses at a gradient of 100 MV/m and a surface magnetic field of 890 kA/m. A temperature rise of up to 250 K was estimated for some shots. The iris surfaces, the location of peak electric field, surprisingly had no damage, but the inner rods, the location of the peak magnetic fields and a large temperature rise, had significant damage. Breakdown in accelerator structures is generally understood in terms of electric field effects. These PBG structure results highlight the unexpected role of magnetic fields in breakdown. The hypothesis is presented that the moderate level electric field on the inner rods, about 14 MV/m, is enhanced at small tips and projections caused by pulsed heating, leading to breakdown. Future PBG structures should be built to minimize pulsed surface heating and temperature rise.

  6. Simulations of Currents in X-Band Accelerator Structures Using 2D and 3D Particle-in-Cell Code

    SciTech Connect

    Dolgashev, Valery A.

    2002-08-14

    Accelerating gradient is one of the crucial parameters affecting design, construction and cost of next-generation linear accelerators. For a specified final energy, the gradient sets the accelerator length, and for a given accelerating structure and pulse repetition rate it determines power consumption. Accelerating gradients on the order of 100 MV/m have been reached in short ({approx} 20cm) standing wave and traveling wave X-band accelerating structures [1, 2, 3]. But recent experiments have shown damage to traveling wave accelerating structures at gradients as low as 50 MV/m after 1000 hours of operation [4]. RF breakdown is a probable cause of this damage. An extensive experimental and theoretical program to determine a safe operating gradient for the Next Linear Collider (NLC) is under way in SLAC. The present work is a part of that program.

  7. Proposal for a study of laser acceleration of electrons using micrograting structures at ATF (Phase 1)

    SciTech Connect

    Chen, W.; Claus, J.; Fernow, R.C.; Fischer, J.; Gallardo, J.C.; Kirk, H.G.; Kramer, H.; Li, Z.; Palmer, R.B.; Rogers, J.; Shrinvasan-Rao, T.; Tsang, T.; Ulc, S.; Veligdan, J.; Warren, J.; Bigio, I.; Kurnit, N.; Shimada, T.; Wang, X.; McDonald, K.T.; Russell, D.P.; Los Alamos National Lab., NM; Princeton Univ., NJ; California Univ., Los Angeles, CA )

    1989-10-29

    We propose to investigate new methods of particle acceleration using a short-pulse CO{sub 2} laser as the power source and grating-like structures as accelerator cavities''. Phase I of this program is intended to demonstrate the principle of the method. We will focus the laser light to a 3 mm line on the surface of the microstructure. The structure is used to transform the electric field pattern of the incoming transversely polarized laser beam to a mode which has a component along the electron beam direction in the vicinity of the surface. With 6 mJ of laser energy and a 6 ps pulse length, the electric field in the spot will be around 1 GV/m. The electron beam from the Brookhaven Accelerator Test Facility (ATF) will be focused transversely within the few micron transverse dimension of the microstructure. The maximum expected acceleration for a 1 GV/m field and a 3 mm acceleration length is 3 MeV. 17 refs., 11 figs., 2 tabs.

  8. Alignment tolerance of accelerating structures and corrections for future linear colliders

    SciTech Connect

    Kubo, K.; Adolphsen, C.; Bane, K.L.F.; Raubenheimer, T.O.; Thompson, K.A.

    1995-06-01

    The alignment tolerance of accelerating structures is estimated by tracking simulations. Both single-bunch and multi-bunch effects are taken into account. Correction schemes for controlling the single and multi-bunch emittance growth in the case of large misalignment are also tested by simulations.

  9. Accelerated safety analyses - structural analyses Phase I - structural sensitivity evaluation of single- and double-shell waste storage tanks

    SciTech Connect

    Becker, D.L.

    1994-11-01

    Accelerated Safety Analyses - Phase I (ASA-Phase I) have been conducted to assess the appropriateness of existing tank farm operational controls and/or limits as now stipulated in the Operational Safety Requirements (OSRs) and Operating Specification Documents, and to establish a technical basis for the waste tank operating safety envelope. Structural sensitivity analyses were performed to assess the response of the different waste tank configurations to variations in loading conditions, uncertainties in loading parameters, and uncertainties in material characteristics. Extensive documentation of the sensitivity analyses conducted and results obtained are provided in the detailed ASA-Phase I report, Structural Sensitivity Evaluation of Single- and Double-Shell Waste Tanks for Accelerated Safety Analysis - Phase I. This document provides a summary of the accelerated safety analyses sensitivity evaluations and the resulting findings.

  10. Damped accelerator structures for future linear e/sup/plus minus// colliders

    SciTech Connect

    Deruyter, H.; Hoag, H.A.; Lisin, A.V.; Loew, G.A.; Palmer, R.B.; Paterson, J.M.; Rago, C.E.; Wang, J.W.

    1989-03-01

    This paper describes preliminary work on accelerator structures for future TeV linear colliders which use trains of e/sup +-/ bunches to reach the required luminosity. These bunch trains, if not perfectly aligned with respect to the accelerator axis, induce transverse wake field modes into the structure. Unless they are sufficiently damped, these modes cause cummulative beam deflections and emittance growth. The envisaged structures, originally proposed by R. B. Palmer, are disk-loaded waveguides in which the disks are slotted radially into quadrants. Wake field energy is coupled via the slots and double-ridged waveguides into a lossy region which is external to the accelerator structure. The requirement is that the Q of the HEM/sub 11/ mode be reduced to a value of less than 30. The work done so far includes MAFIA code computations and low power rf measurements to study the fields. A four-cavity 2..pi../3 mode standing-wave structure has been built to find whether the slots lower the electric breakdown thresholds below those reached with conventional disk-loaded structures. We set out to assess the microwave properties of the structure and the problems which might be encountered in fabricating it. 4 refs., 7 figs.

  11. Rapid analysis of scattering from periodic dielectric structures using accelerated Cartesian expansions

    SciTech Connect

    Baczewski, Andrew David; Miller, Nicholas C.; Shanker, Balasubramaniam

    2012-03-22

    Here, the analysis of fields in periodic dielectric structures arise in numerous applications of recent interest, ranging from photonic bandgap structures and plasmonically active nanostructures to metamaterials. To achieve an accurate representation of the fields in these structures using numerical methods, dense spatial discretization is required. This, in turn, affects the cost of analysis, particularly for integral-equation-based methods, for which traditional iterative methods require Ο(Ν2) operations, Ν being the number of spatial degrees of freedom. In this paper, we introduce a method for the rapid solution of volumetric electric field integral equations used in the analysis of doubly periodic dielectric structures. The crux of our method is the accelerated Cartesian expansion algorithm, which is used to evaluate the requisite potentials in Ο(Ν) cost. Results are provided that corroborate our claims of acceleration without compromising accuracy, as well as the application of our method to a number of compelling photonics applications.

  12. Simulation of variation characteristics at thermostabilization of 27 GHz biperiodical accelerating structure

    NASA Astrophysics Data System (ADS)

    Kluchevskaya, Y. D.; Polozov, S. M.

    2016-07-01

    It was proposed to develop the biperiodical accelerating structure with operating frequency of 27 GHz to assess the possibility of design a compact accelerating structure for medical application. It is necessary to do the more careful simulation of variation characteristics this case because of decrease of wavelength 3-10 times in comparison with conventional structures 10 and 3 cm ranges. Results of such study are presented in the article. Also a combination of high electromagnetic fields and long pulses at a high operating frequency leads to the temperature increase in the structure, thermal deformation and significant change of the resonator characteristics, including the frequency of the RF pulse. Development results of three versions of system of temperature stabilization also discuses.

  13. Enhanced proton acceleration by an ultrashort laser interaction with structured dynamic plasma targets.

    PubMed

    Zigler, A; Eisenman, S; Botton, M; Nahum, E; Schleifer, E; Baspaly, A; Pomerantz, I; Abicht, F; Branzel, J; Priebe, G; Steinke, S; Andreev, A; Schnuerer, M; Sandner, W; Gordon, D; Sprangle, P; Ledingham, K W D

    2013-05-24

    We experimentally demonstrate a notably enhanced acceleration of protons to high energy by relatively modest ultrashort laser pulses and structured dynamical plasma targets. Realized by special deposition of snow targets on sapphire substrates and using carefully planned prepulses, high proton yields emitted in a narrow solid angle with energy above 21 MeV were detected from a 5 TW laser. Our simulations predict that using the proposed scheme protons can be accelerated to energies above 150 MeV by 100 TW laser systems.

  14. Solving Large Sparse Linear Systems in End-to-end Accelerator Structure Simulations

    SciTech Connect

    Lee, L

    2004-01-23

    This paper presents a case study of solving very large sparse linear systems in end-to-end accelerator structure simulations. Both direct solvers and iterative solvers are investigated. A parallel multilevel preconditioner based on hierarchical finite element basis functions is considered and has been implemented to accelerate the convergence of iterative solvers. A linear system with matrix size 93,147,736 and with 3,964,961,944 non-zeros from 3D electromagnetic finite element discretization has been solved in less than 8 minutes with 1024 CPUs on the NERSC IBM SP. The resource utilization as well as the application performance for these solvers is discussed.

  15. A two-fluid model for black-hole accretion flows: particle acceleration and disc structure

    NASA Astrophysics Data System (ADS)

    Lee, Jason P.; Becker, Peter A.

    2017-02-01

    Hot, tenuous advection-dominated accretion flows around black holes are ideal sites for the Fermi acceleration of relativistic particles at standing shock waves in the accretion disc. Previous work has demonstrated that the shock-acceleration process can be efficient enough to power the observed, strong outflows in radio-loud active galaxies such as M87. However, the dynamical effect (back-reaction) on the flow, exerted by the pressure of the relativistic particles, has not been previously considered, and this effect can have a significant influence on the disc structure. We reexamine the problem by developing a new, two-fluid model for the structure of the accretion disc that includes the dynamical effect of the relativistic particle pressure, combined with the pressure of the background (thermal) gas. The new model is analogous to the two-fluid model of cosmic ray acceleration in supernova-driven shock waves. As part of the model, we also develop a new set of shock jump conditions, which are solved along with the hydrodynamic conservation equations to determine the structure of the accretion disc. The solutions include the formation of a mildly relativistic outflow (jet) at the shock radius, driven by the relativistic particles accelerated in the disc. One of our main conclusions is that in the context of the new two-fluid accretion model, global smooth (shock-free) solutions do not exist, and the disc must always contain a standing shock wave, at least in the inviscid case considered here.

  16. Statistical model for field emitter activation on metallic surfaces used in high-gradient accelerating structures

    NASA Astrophysics Data System (ADS)

    Lagotzky, S.; Müller, G.

    2016-01-01

    Both super- and normal-conducting high-gradient linear accelerators are limited by enhanced field emission (EFE) in the accelerating structures, e.g. due to power loss or ignition of discharges. We discuss the dependence of the number density of typical emitters, i.e. particulates and surface defects, on the electric field level at which they are activated for naturally oxidized metallic surfaces. This activation is explained by the transition of a metal-insulator interface into geometric features that enhance the EFE process. A statistical model is successfully compared to systematic studies of niobium and copper relevant for recent and future linear accelerators. Our results show that the achievable surface quality of Nb might be sufficient for the suppression of EFE in the superconducting accelerating structures for the actual European XFEL but not for the planned International Linear Collider. Moreover, some effort will be required to reduce EFE and thus the breakdown rate of the normal conducting Cu structures for the Compact Linear Collider.

  17. Dynamic behavior of time-delayed acceleration feedback controller for active vibration control of flexible structures

    NASA Astrophysics Data System (ADS)

    An, Fang; Chen, Wei-dong; Shao, Min-qiang

    2014-09-01

    This paper addresses the design problem of the controller with time-delayed acceleration feedback. On the basis of the reduction method and output state-derivative feedback, a time-delayed acceleration feedback controller is proposed. Stability boundaries of the closed-loop system are determined by using Hurwitz stability criteria. Due to the introduction of time delay into the controller with acceleration feedback, the proposed controller has the feature of not only changing the mass property but also altering the damping property of the controlled system in the sense of equivalent structural modification. With this feature, the closed-loop system has a greater logarithmic decrement than the uncontrolled one, and in turn, the control behavior can be improved. In this connection, the time delay in the acceleration feedback control is a positive factor when satisfying some given conditions and it could be actively utilized. On the ground of the analysis, the developed controller is implemented on a cantilever beam for different controller gain-delay combinations, and the control performance is evaluated with the comparison to that of pure acceleration feedback controller. Simulation and experimental results verify the ability of the controller to attenuate the vibration resulting from the dominant mode.

  18. Particle Acceleration Affected by the Evolving Velocity Structures in the Solar Wind

    NASA Astrophysics Data System (ADS)

    Tsubouchi, K.

    2015-12-01

    It is accepted that high-energy particles are efficiently generated during their crossing of shocks in space, where the diffusive shock acceleration is the most standard process to explain the observed energy spectrum beyond the order of a gigaelectronvolt. In contrast, recent spacecraft observations have shown different characteristics in a lower energy range (a kilo- to megaelectronvolt): particles in the heliosphere have a power-law spectrum in particle speed with a spectral index of -5, which is commonly found in any solar wind conditions. This is a puzzling result that the shocks are not a necessary element responsible for accelerating particles. The alternative mechanism, a pump acceleration, is proposed where particles are accelerated in a region containing large-scale compressions and expansions (e.g., Fisk and Gloeckler, JGR 2014). In the present study, we elucidate the validity of this mechanism by performing hybrid simulations to investigate the particle, particularly pickup ions, dynamics in various situations of non-uniform velocity field, such as a simple fast/slow flow interaction, sinusoidal structures, or random profiles, and to compare the velocity spectrum of suprathermal particles in each case. We also study the scale dependence of acceleration processes by comparing the spectrum of the energetic H+, He+, and O+.

  19. Wire Measurement of Impedance of an X-Band Accelerating Structure

    SciTech Connect

    Baboi, N

    2004-09-02

    Several tens of thousands of accelerator structures will be needed for the next generation of normal conducting linear colliders known as the GLC/NLC (Global Linear Collider/Next Linear Collider). To prevent the beam being driven into a disruptive BBU (Beam Break-Up) mode or at the very least, the emittance being significantly diluted, it is important to damp down the wakefield left by driving bunches to a manageable level. Manufacturing errors and errors in design need to be measured and compared with prediction. In this paper a bench-top method of measuring transverse impedances in X-band accelerating structures is described. Utilizing an off-axis wire the S parameters are measured and converted to impedance. Measurements in a damped and detuned structure built for GLC/NLC are presented and the results are discussed.

  20. Diamond field emitter array cathodes and possibilities of employing additive manufacturing for dielectric laser accelerating structures

    NASA Astrophysics Data System (ADS)

    Simakov, Evgenya I.; Andrews, Heather L.; Herman, Matthew J.; Hubbard, Kevin M.; Weis, Eric

    2017-03-01

    Demonstration of a stand-alone practical dielectric laser accelerator (DLA) requires innovation in two major critical components: high-current ultra-low-emittance cathodes and efficient laser accelerator structures. LANL develops two technologies that in our opinion are applicable to the novel DLA architectures: diamond field emitter array (DFEA) cathodes and additive manufacturing of photonic band-gap (PBG) structures. This paper discusses the results of testing of DFEA cathodes in the field-emission regime and the possibilities for their operation in the photoemission regime, and compares their emission characteristics to the specific needs of DLAs. We also describe recent advances in additive manufacturing of dielectric woodpile structures using a Nanoscribe direct laser-writing device capable of maskless lithography and additive manufacturing, and the development of novel infrared dielectric materials compatible with additive manufacturing.

  1. Diamond field emitter array cathodes and possibilities for employing additive manufacturing for dielectric laser accelerating structures

    SciTech Connect

    Simakov, Evgenya Ivanovna; Andrews, Heather Lynn; Herman, Matthew Joseph; Hubbard, Kevin Mark; Weis, Eric

    2016-09-20

    These are slides for a presentation at Stanford University. The outline is as follows: Motivation: customers for compact accelerators, LANL's technologies for laser acceleration, DFEA cathodes, and additive manufacturing of micron-size structures. Among the stated conclusions are the following: preliminary study identified DFEA cathodes as promising sources for DLAs--high beam current and small emittance; additive manufacturing with Nanoscribe Professional GT can produce structures with the right scale features for a DLA operating at micron wavelengths (fabrication tolerances need to be studied, DLAs require new materials). Future plans include DLA experiment with a beam produced by the DFEA cathode with field emission, demonstration of photoemission from DFEAs, and new structures to print and test.

  2. Summary of the Normal-Conducting Accelerating Structures for LEDA and APT

    NASA Astrophysics Data System (ADS)

    Schneider, J. David

    1998-04-01

    The accelerator production of tritium (APT) plant requires a continuous (100% duty-factor), 100-mA, 1000--1700-MeV proton beam. Superconducting structures will accelerate protons above about 200 MeV, but room-temperature, normal-conducting (NC) copper structures will be used for lower energies. We will assemble the front 11-MeV portion of this NC accelerator as the low-energy demonstration accelerator (LEDA). This presentation will cover the demonstated operation of the proton injector, the design, fabrication, and tuning status of the 6.7-MeV RFQ, and the design features of the CCDTL (coupled-cavity drift-tube linac) that will accelerate protons to 100 MeV, before use of a conventional CCL (coupled-cavity linac). Several innovative features result in improved performance, ease of use, and improved reliabiltiy. The75-keV injector features a microwave ion source, dual-solenoid transport, and has no electronics at high potential. Its demonstrated high efficiency (less than 800 Watts), excellent proton fraction (>90%), high current (>110 mA), and reliability make it attractive for several other high-current applications. The 6.7-MeV, 350-MHz RFQ is an 8-meter-long, brazed-copper structure with hundreds of cooling channels that carry away the 1.3 MW of waste heat. During beam operation, only the cooling-water temperature is adjustable to maintain structure resonance. LEDA's 700-MHz CCDTL structure is new, combining features of the conventional DTL and CCL structures. All focus magnets are external to the copper accelerating cavities, each of which contains either one or two drift tubes. A `hot model' will validate fabrication, cooling, tuning, and coupling techniques. The LEDA facility is being upgraded with 15 MW of power and cooling utiliites, to support seven 1-MW cw RF systems needed to power all structures. The first few of these 1.3 MW 350-MHz systems are operational, and extensive testing was completed on the critical RF windows. Updates will be given on the

  3. Laser Wakefield Acceleration: Structural and Dynamic Studies. Final Technical Report ER40954

    SciTech Connect

    Downer, Michael C.

    2014-04-30

    Particle accelerators enable scientists to study the fundamental structure of the universe, but have become the largest and most expensive of scientific instruments. In this project, we advanced the science and technology of laser-plasma accelerators, which are thousands of times smaller and less expensive than their conventional counterparts. In a laser-plasma accelerator, a powerful laser pulse exerts light pressure on an ionized gas, or plasma, thereby driving an electron density wave, which resembles the wake behind a boat. Electrostatic fields within this plasma wake reach tens of billions of volts per meter, fields far stronger than ordinary non-plasma matter (such as the matter that a conventional accelerator is made of) can withstand. Under the right conditions, stray electrons from the surrounding plasma become trapped within these “wake-fields”, surf them, and acquire energy much faster than is possible in a conventional accelerator. Laser-plasma accelerators thus might herald a new generation of compact, low-cost accelerators for future particle physics, x-ray and medical research. In this project, we made two major advances in the science of laser-plasma accelerators. The first of these was to accelerate electrons beyond 1 gigaelectronvolt (1 GeV) for the first time. In experimental results reported in Nature Communications in 2013, about 1 billion electrons were captured from a tenuous plasma (about 1/100 of atmosphere density) and accelerated to 2 GeV within about one inch, while maintaining less than 5% energy spread, and spreading out less than ½ milliradian (i.e. ½ millimeter per meter of travel). Low energy spread and high beam collimation are important for applications of accelerators as coherent x-ray sources or particle colliders. This advance was made possible by exploiting unique properties of the Texas Petawatt Laser, a powerful laser at the University of Texas at Austin that produces pulses of 150 femtoseconds (1 femtosecond is 10

  4. The sense of balance in humans: Structural features of otoconia and their response to linear acceleration.

    PubMed

    Kniep, Rüdiger; Zahn, Dirk; Wulfes, Jana; Walther, Leif Erik

    2017-01-01

    We explored the functional role of individual otoconia within the otolith system of mammalians responsible for the detection of linear accelerations and head tilts in relation to the gravity vector. Details of the inner structure and the shape of intact human and artificial otoconia were studied using environmental scanning electron microscopy (ESEM), including decalcification by ethylenediaminetetraacetic acid (EDTA) to discriminate local calcium carbonate density. Considerable differences between the rhombohedral faces of human and artificial otoconia already indicate that the inner architecture of otoconia is not consistent with the point group -3m. This is clearly confirmed by decalcified otoconia specimen which are characterized by a non-centrosymmetric volume distribution of the compact 3+3 branches. This structural evidence for asymmetric mass distribution was further supported by light microscopy in combination with a high speed camera showing the movement of single otoconia specimen (artificial specimen) under gravitational influence within a viscous medium (artificial endolymph). Moreover, the response of otoconia to linear acceleration forces was investigated by particle dynamics simulations. Both, time-resolved microscopy and computer simulations of otoconia acceleration show that the dislocation of otoconia include significant rotational movement stemming from density asymmetry. Based on these findings, we suggest an otolith membrane expansion/stiffening mechanism for enhanced response to linear acceleration transmitted to the vestibular hair cells.

  5. Magnetosheath filamentary structures formed by ion acceleration at the quasi-parallel bow shock

    NASA Astrophysics Data System (ADS)

    Omidi, N.; Sibeck, D.; Gutynska, O.; Trattner, K. J.

    2014-04-01

    Results from 2.5-D electromagnetic hybrid simulations show the formation of field-aligned, filamentary plasma structures in the magnetosheath. They begin at the quasi-parallel bow shock and extend far into the magnetosheath. These structures exhibit anticorrelated, spatial oscillations in plasma density and ion temperature. Closer to the bow shock, magnetic field variations associated with density and temperature oscillations may also be present. Magnetosheath filamentary structures (MFS) form primarily in the quasi-parallel sheath; however, they may extend to the quasi-perpendicular magnetosheath. They occur over a wide range of solar wind Alfvénic Mach numbers and interplanetary magnetic field directions. At lower Mach numbers with lower levels of magnetosheath turbulence, MFS remain highly coherent over large distances. At higher Mach numbers, magnetosheath turbulence decreases the level of coherence. Magnetosheath filamentary structures result from localized ion acceleration at the quasi-parallel bow shock and the injection of energetic ions into the magnetosheath. The localized nature of ion acceleration is tied to the generation of fast magnetosonic waves at and upstream of the quasi-parallel shock. The increased pressure in flux tubes containing the shock accelerated ions results in the depletion of the thermal plasma in these flux tubes and the enhancement of density in flux tubes void of energetic ions. This results in the observed anticorrelation between ion temperature and plasma density.

  6. Magnetosheath Filamentary Structures Formed by Ion Acceleration at the Quasi-Parallel Bow Shock

    NASA Technical Reports Server (NTRS)

    Omidi, N.; Sibeck, D.; Gutynska, O.; Trattner, K. J.

    2014-01-01

    Results from 2.5-D electromagnetic hybrid simulations show the formation of field-aligned, filamentary plasma structures in the magnetosheath. They begin at the quasi-parallel bow shock and extend far into the magnetosheath. These structures exhibit anticorrelated, spatial oscillations in plasma density and ion temperature. Closer to the bow shock, magnetic field variations associated with density and temperature oscillations may also be present. Magnetosheath filamentary structures (MFS) form primarily in the quasi-parallel sheath; however, they may extend to the quasi-perpendicular magnetosheath. They occur over a wide range of solar wind Alfvénic Mach numbers and interplanetary magnetic field directions. At lower Mach numbers with lower levels of magnetosheath turbulence, MFS remain highly coherent over large distances. At higher Mach numbers, magnetosheath turbulence decreases the level of coherence. Magnetosheath filamentary structures result from localized ion acceleration at the quasi-parallel bow shock and the injection of energetic ions into the magnetosheath. The localized nature of ion acceleration is tied to the generation of fast magnetosonic waves at and upstream of the quasi-parallel shock. The increased pressure in flux tubes containing the shock accelerated ions results in the depletion of the thermal plasma in these flux tubes and the enhancement of density in flux tubes void of energetic ions. This results in the observed anticorrelation between ion temperature and plasma density.

  7. New Features of Time Domain Electric-Field Structures in the Auroral Acceleration Region

    SciTech Connect

    Mozer, F.S.; Ergun, R.; Temerin, M.; Cattell, C.; Dombeck, J.; Wygant, J.

    1997-08-01

    The Polar Satellite carries the first three-axis electric field detector flown in the magnetosphere. Its direct measurement of electric field components perpendicular and parallel to the local magnetic field has revealed new classes and features of electric field structures associated with the plasma acceleration that produces discrete auroras and that populates the magnetosphere with plasma of ionospheric origin. These structures, associated with the hydrogen ion cyclotron mode, include very large solitary waves, spiky field structures, wave envelopes of parallel electric fields, and very large amplitude, nonlinear, coherent ion cyclotron waves. {copyright} {ital 1997} {ital The American Physical Society}

  8. Determination of the acceleration region size in a loop-structured solar flare

    NASA Astrophysics Data System (ADS)

    Guo, J.; Emslie, A. G.; Kontar, E. P.; Benvenuto, F.; Massone, A. M.; Piana, M.

    2012-07-01

    Aims: To study the acceleration and propagation of bremsstrahlung-producing electrons in solar flares, we analyze the evolution of the flare loop size with respect to energy at a variety of times. A GOES M3.7 loop-structured flare starting around 23:55 on 2002 April 14 is studied in detail using Ramaty High Energy Solar Spectroscopic Imager (RHESSI) observations. Methods: We construct photon and mean-electron-flux maps in 2-keV energy bins by processing observationally-deduced photon and electron visibilities, respectively, through several image-processing methods: a visibility-based forward-fit (FWD) algorithm, a maximum entropy (MEM) procedure and the uv-smooth (UVS) approach. We estimate the sizes of elongated flares (i.e., the length and width of flaring loops) by calculating the second normalized moments of the intensity in any given map. Employing a collisional model with an extended acceleration region, we fit the loop lengths as a function of energy in both the photon and electron domains. Results: The resulting fitting parameters allow us to estimate the extent of the acceleration region which is between ~ 13 arcsec and ~19 arcsec. Both forward-fit and uv-smooth algorithms provide substantially similar results with a systematically better fit in the electron domain. Conclusions: The consistency of the estimates from these methods provides strong support that the model can reliably determine geometric parameters of the acceleration region. The acceleration region is estimated to be a substantial fraction (~1/2) of the loop extent, indicating that this dense flaring loop incorporates both acceleration and transport of electrons, with concurrent thick-target bremsstrahlung emission.

  9. Parallel Computation of Integrated Electromagnetic, Thermal and Structural Effects for Accelerator Cavities

    SciTech Connect

    Akcelik, V.; Candel, A.E.; Kabel, A.C.; Ko, K.; Lee, L.; Li, Z.; Ng, C.K.; Xiao, L.; /SLAC

    2011-11-02

    The successful operation of accelerator cavities has to satisfy both rf and mechanical requirements. It is highly desirable that electromagnetic, thermal and structural effects such as cavity wall heating and Lorentz force detuning in superconducting rf cavities can be addressed in an integrated analysis. Based on the SLAC parallel finite-element code infrastructure for electromagnetic modeling, a novel multi-physics analysis tool has been developed to include additional thermal and mechanical effects. The parallel computation enables virtual prototyping of accelerator cavities on computers, which would substantially reduce the cost and time of a design cycle. The multi-physics tool is applied to the LCLS rf gun for electromagnetic, thermal and structural analyses.

  10. Acceleration response spectrum for prediction of structural vibration due to individual bouncing

    NASA Astrophysics Data System (ADS)

    Chen, Jun; Wang, Lei; Racic, Vitomir; Lou, Jiayue

    2016-08-01

    This study is designed to develop an acceleration response spectrum that can be used in vibration serviceability assessment of civil engineering structures, such as floors and grandstands those are dynamically excited by individual bouncing. The spectrum is derived from numerical simulations and statistical analysis of acceleration responses of a single degree of freedom system with variable natural frequency and damping under a large number of experimentally measured individual bouncing loads. Its mathematical representation is fit for fast yet reliable application in design practice and is comprised of three equations that describe three distinct frequency regions observed in the actual data: the first resonant plateau (2-3.5 Hz), the second resonant plateau (4-7 Hz) and a descension region (7-15 Hz). Finally, this paper verifies the proposed response spectrum approach to predict structural vibration by direct comparison against numerical simulations and experimental results.

  11. Advances in X-Band TW Accelerator Structures Operating in the 100 MV/M Regime

    SciTech Connect

    Higo, Toshiyasu; Higashi, Yasuo; Matsumoto, Shuji; Yokoyama, Kazue; Adolphsen, Chris; Dolgashev, Valery; Jensen, Aaron; Laurent, Lisa; Tantawi, Sami; Wang, Faya; Wang, Juwen; Dobert, Steffen; Grudiev, Alexej; Riddone, Germana; Wuensch, Walter; Zennaro, Riccardo; /CERN

    2012-07-05

    A CERN-SLAC-KEK collaboration on high gradient X-band accelerator structure development for CLIC has been ongoing for three years. The major outcome has been the demonstration of stable 100 MV/m gradient operation of a number of CLIC prototype structures. These structures were fabricated using the technology developed from 1994 to 2004 for the GLC/NLC linear collider initiative. One of the goals has been to refine the essential parameters and fabrication procedures needed to realize such a high gradient routinely. Another goal has been to develop structures with stronger dipole mode damping than those for GLC/NLC. The latter requires that the surface temperature rise during the pulse be higher, which may increase the breakdown rate. One structure with heavy damping has been RF processed and another is nearly finished. The breakdown rates of these structures were found to be higher by two orders of magnitude compared to those with equivalent acceleration mode parameters but without the damping features. This paper presents these results together with some of the earlier results from non-damped structures.

  12. An L-Band Superconducting Traveling Wave Accelerating Structure With Feedback

    SciTech Connect

    Kanareykin, A.; Avrakhov, P.; Yakovlev, V. P.; Solyak, N.; Kazakov, S.

    2009-01-22

    The most severe problem of the International Linear Collider is its high cost, resulting in part from the enormous length of the collider. This length is determined mainly by the achievable accelerating gradient in the RF system of the ILC. In the ILC project the required accelerating gradient is higher than 30 MeV/m. Further improvement of the coupling to the beam may be achieved by using a Traveling Wave SC structure [1]. We have demonstrated that an additional gradient increase of up to 46% may be possible if a {pi}/2 TW SC structure is employed. However, a TW SC structure requires a SC feedback waveguide to return the few GW of circulating RF power from the structure output back to the structure input. The test cavity with feedback is designed to demonstrate the possibility of achieving a significantly higher gradient than existing SC structures. The double-coupler powering excitation and tuning have been studied numerically and the corresponding model results are presented. The proposed double-coupler powering scheme significantly reduces the tuning requirements as long as any of the partial modes of given magnitude and phase are excited independently, providing a clear traveling wave regime of structure operation.

  13. Spatial structure of the neck and acceleration processes in a micropinch

    SciTech Connect

    Dolgov, A. N.; Klyachin, N. A.; Prokhorovich, D. E.

    2016-12-15

    It is shown that the spatial structure of the micropinch neck during the transition from magnetohydrodynamic to radiative compression and the bremsstrahlung spectrum of the discharge in the photon energy range of up to 30 keV depend on the configuration of the inner electrode of the coaxial electrode system of the micropinch discharge. Analysis of the experimental results indicates that the acceleration processes in the electron component of the micropinch plasma develop earlier than radiative compression.

  14. Damping of higher-order modes in a threefold symmetry accelerating structure

    SciTech Connect

    Yu, D.; Kroll, N. |

    1991-12-31

    We investigate a waveguide-coupled damping structure with threefold symmetry using the 2-D and 3-D MAFIA codes. Within the frequency range considered, all higher order modes except the TM011 and TE111 modes are heavily damped. Possible ways to detrap these by using asymmetric waveguides offset with respect to the accelerating cavity in the direction of the beam are studied. External Qs and resonant frequencies are calculated using recently developed computer methods.

  15. Damping of Higher-Order Modes in a Threefold Symmetry Accelerating Structure

    SciTech Connect

    Yu, D.

    2005-04-08

    The authors investigate a waveguide-coupled damping structure with threefold symmetry using the 2-D and 3-D MAFIA codes. Within the frequency range considered, all higher order modes except the TM011 and TE111 modes are heavily damped. Possible ways to detrap these by using asymmetric waveguides offset with respect to the accelerating cavity in the direction of the beam are studied. External Qs and resonant frequencies are calculated using recently developed computer methods.

  16. Spatial structure of the neck and acceleration processes in a micropinch

    NASA Astrophysics Data System (ADS)

    Dolgov, A. N.; Klyachin, N. A.; Prokhorovich, D. E.

    2016-12-01

    It is shown that the spatial structure of the micropinch neck during the transition from magnetohydrodynamic to radiative compression and the bremsstrahlung spectrum of the discharge in the photon energy range of up to 30 keV depend on the configuration of the inner electrode of the coaxial electrode system of the micropinch discharge. Analysis of the experimental results indicates that the acceleration processes in the electron component of the micropinch plasma develop earlier than radiative compression.

  17. Studies of coupled cavity LINAC (CCL) accelerating structures with 3-D codes

    SciTech Connect

    Spalek, G.

    2000-08-01

    The cw CCL being designed for the Accelerator Production of Tritium (APT) project accelerates protons from 96 MeV to 211 MeV. It consists of 99 segments each containing up to seven accelerating cavities. Segments are coupled by intersegment coupling cavities and grouped into supermodules. The design method needs to address not only basic cavity sizing for a given coupling and pi/2 mode frequency, but also the effects of high power densities on the cavity frequency, mechanical stresses, and the structure's stop band during operation. On the APT project, 3-D RF (Ansoft Corp.'s HFSS) and coupled RF/structural (Ansys Inc.'s ANSYS) codes are being used. to develop tools to address the above issues and guide cooling channel design. The code's predictions are being checked against available low power Aluminum models. Stop band behavior under power will be checked once the tools are extended to CCDTL structures that have been tested at high power. A summary of calculations made to date and agreement with measured results will be presented.

  18. Sensor fusion for structural tilt estimation using an acceleration-based tilt sensor and a gyroscope

    NASA Astrophysics Data System (ADS)

    Liu, Cheng; Park, Jong-Woong; Spencer, B. F., Jr.; Moon, Do-Soo; Fan, Jiansheng

    2017-10-01

    A tilt sensor can provide useful information regarding the health of structural systems. Most existing tilt sensors are gravity/acceleration based and can provide accurate measurements of static responses. However, for dynamic tilt, acceleration can dramatically affect the measured responses due to crosstalk. Thus, dynamic tilt measurement is still a challenging problem. One option is to integrate the output of a gyroscope sensor, which measures the angular velocity, to obtain the tilt; however, problems arise because the low-frequency sensitivity of the gyroscope is poor. This paper proposes a new approach to dynamic tilt measurements, fusing together information from a MEMS-based gyroscope and an acceleration-based tilt sensor. The gyroscope provides good estimates of the tilt at higher frequencies, whereas the acceleration measurements are used to estimate the tilt at lower frequencies. The Tikhonov regularization approach is employed to fuse these measurements together and overcome the ill-posed nature of the problem. The solution is carried out in the frequency domain and then implemented in the time domain using FIR filters to ensure stability. The proposed method is validated numerically and experimentally to show that it performs well in estimating both the pseudo-static and dynamic tilt measurements.

  19. Structure-Based Drug Discovery Accelerated by Many-Core Devices.

    PubMed

    Feinstein, Wei; Brylinski, Michal

    2016-01-01

    Computer-aided design is one of the critical components of modern drug discovery. Drug development is routinely streamlined using computational approaches to improve hit identification and lead selection, enhance bioavailability, and reduce toxicity. A mounting body of genomic knowledge accumulated during the last decade or so presents great opportunities for pharmaceutical research. However, new challenges also arose because processing this large volume of data demands unprecedented computing resources. On the other hand, the state-of-the-art heterogeneous systems deliver petaflops of peak performance to accelerate scientific discovery. In this communication, we review modern parallel accelerator architectures, mainly focusing on Intel Xeon Phi many-core devices. Xeon Phi is a relatively new platform that features tens of computing cores with hundreds of threads offering massively parallel capabilities for a broad range of application. We also discuss common parallel programming frameworks targeted to this accelerator, including OpenMP, OpenCL, MPI and HPX. Recent advances in code development for many-core devices are described to demonstrate the advantages of heterogeneous implementations over the traditional, serial computing. Finally, we highlight selected algorithms, eFindSite, a ligand binding site predictor, a force field for bio-molecular simulations, and BUDE, a structure-based virtual screening engine, to demonstrate how modern drug discovery is accelerated by heterogeneous systems equipped with parallel computing devices.

  20. Self-mapping the longitudinal field structure of a nonlinear plasma accelerator cavity

    DOE PAGES

    Clayton, C. E.; Adli, E.; Allen, J.; ...

    2016-08-16

    The preservation of emittance of the accelerating beam is the next challenge for plasma-based accelerators envisioned for future light sources and colliders. The field structure of a highly nonlinear plasma wake is potentially suitable for this purpose but has not been yet measured. Here we show that the longitudinal variation of the fields in a nonlinear plasma wakefield accelerator cavity produced by a relativistic electron bunch can be mapped using the bunch itself as a probe. We find that, for much of the cavity that is devoid of plasma electrons, the transverse force is constant longitudinally to within ±3% (r.m.s.).more » Moreover, comparison of experimental data and simulations has resulted in mapping of the longitudinal electric field of the unloaded wake up to 83 GV m–1 to a similar degree of accuracy. Lastly, these results bode well for high-gradient, high-efficiency acceleration of electron bunches while preserving their emittance in such a cavity.« less

  1. Self-mapping the longitudinal field structure of a nonlinear plasma accelerator cavity

    SciTech Connect

    Clayton, C. E.; Adli, E.; Allen, J.; An, W.; Clarke, C. I.; Corde, S.; Frederico, J.; Gessner, S.; Green, S. Z.; Hogan, M. J.; Joshi, C.; Litos, M.; Lu, W.; Marsh, K. A.; Mori, W. B.; Vafaei-Najafabadi, N.; Xu, X.; Yakimenko, V.

    2016-08-16

    The preservation of emittance of the accelerating beam is the next challenge for plasma-based accelerators envisioned for future light sources and colliders. The field structure of a highly nonlinear plasma wake is potentially suitable for this purpose but has not been yet measured. Here we show that the longitudinal variation of the fields in a nonlinear plasma wakefield accelerator cavity produced by a relativistic electron bunch can be mapped using the bunch itself as a probe. We find that, for much of the cavity that is devoid of plasma electrons, the transverse force is constant longitudinally to within ±3% (r.m.s.). Moreover, comparison of experimental data and simulations has resulted in mapping of the longitudinal electric field of the unloaded wake up to 83 GV m–1 to a similar degree of accuracy. Lastly, these results bode well for high-gradient, high-efficiency acceleration of electron bunches while preserving their emittance in such a cavity.

  2. Self-mapping the longitudinal field structure of a nonlinear plasma accelerator cavity

    PubMed Central

    Clayton, C. E.; Adli, E.; Allen, J.; An, W.; Clarke, C. I.; Corde, S.; Frederico, J.; Gessner, S.; Green, S. Z.; Hogan, M. J.; Joshi, C.; Litos, M.; Lu, W.; Marsh, K. A.; Mori, W. B.; Vafaei-Najafabadi, N.; Xu, X.; Yakimenko, V.

    2016-01-01

    The preservation of emittance of the accelerating beam is the next challenge for plasma-based accelerators envisioned for future light sources and colliders. The field structure of a highly nonlinear plasma wake is potentially suitable for this purpose but has not been yet measured. Here we show that the longitudinal variation of the fields in a nonlinear plasma wakefield accelerator cavity produced by a relativistic electron bunch can be mapped using the bunch itself as a probe. We find that, for much of the cavity that is devoid of plasma electrons, the transverse force is constant longitudinally to within ±3% (r.m.s.). Moreover, comparison of experimental data and simulations has resulted in mapping of the longitudinal electric field of the unloaded wake up to 83 GV m−1 to a similar degree of accuracy. These results bode well for high-gradient, high-efficiency acceleration of electron bunches while preserving their emittance in such a cavity. PMID:27527569

  3. GPU-Accelerated Analysis and Visualization of Large Structures Solved by Molecular Dynamics Flexible Fitting

    PubMed Central

    McGreevy, Ryan; Isralewitz, Barry

    2014-01-01

    Hybrid structure fitting methods combine data from cryo-electron microscopy and X-ray crystallography with molecular dynamics simulations for the determination of all-atom structures of large biomolecular complexes. Evaluating the quality-of-fit obtained from hybrid fitting is computationally demanding, particularly in the context of a multiplicity of structural conformations that must be evaluated. Existing tools for quality-of-fit analysis and visualization have previously targeted small structures and are too slow to be used interactively for large biomolecular complexes of particular interest today such as viruses or for long molecular dynamics trajectories as they arise in protein folding. We present new data-parallel and GPU-accelerated algorithms for rapid interactive computation of quality-of-fit metrics linking all-atom structures and molecular dynamics trajectories to experimentally determined density maps obtained from cryo-electron microscopy or X-ray crystallography. We evaluate the performance and accuracy of the new quality-of-fit analysis algorithms vis-a-vis existing tools, examine algorithm performance on GPU-accelerated desktop workstations and supercomputers, and describe new visualization techniques for results of hybrid structure fitting methods. PMID:25340325

  4. Enhancing Target Normal Sheath Accelerated Ions with Micro-structured Targets

    NASA Astrophysics Data System (ADS)

    George, Kevin; Snyder, Joseph; Ji, Liangliang; Rubin, Trevor; Handler, Abraham; Poole, Patrick; Willis, Christopher; Daskalova, Rebecca; Cochran, Ginevra; Schumacher, Douglass

    2016-10-01

    Laser driven target normal sheath acceleration (TNSA) of ions has been widely studied due to its fundamental importance, use as a probe, and for possible applications such as cancer therapy and neutron generation. Much of this work has been conducted on thin foils with peak ion energy and yield optimized using laser parameters such as energy and spot size. Micro-structured targets, however, have demonstrated increased peak ion energy and yield by controlling and enhancing mechanisms preferential to TNSA. Novel micro-structured targets were developed using optical lithography techniques on thin substrates at the OSU NanoSystem Laboratory. Variable structure height (0.5-2 micron) and transverse patterning (up to 1 micron resolution) permit the survey of a range of structured target variables in the study of ion acceleration. We describe the development of these targets and an experiment investigating the enhancement of TNSA ions from lithography produced micro-structured targets conducted at the Scarlet Laser Facility. Experimental results show increased proton and Carbon yield >2 MeV and higher peak Carbon energy from structured targets. This work was supported by the Air Force Office of Scientific Research.

  5. GPU-accelerated analysis and visualization of large structures solved by molecular dynamics flexible fitting.

    PubMed

    Stone, John E; McGreevy, Ryan; Isralewitz, Barry; Schulten, Klaus

    2014-01-01

    Hybrid structure fitting methods combine data from cryo-electron microscopy and X-ray crystallography with molecular dynamics simulations for the determination of all-atom structures of large biomolecular complexes. Evaluating the quality-of-fit obtained from hybrid fitting is computationally demanding, particularly in the context of a multiplicity of structural conformations that must be evaluated. Existing tools for quality-of-fit analysis and visualization have previously targeted small structures and are too slow to be used interactively for large biomolecular complexes of particular interest today such as viruses or for long molecular dynamics trajectories as they arise in protein folding. We present new data-parallel and GPU-accelerated algorithms for rapid interactive computation of quality-of-fit metrics linking all-atom structures and molecular dynamics trajectories to experimentally-determined density maps obtained from cryo-electron microscopy or X-ray crystallography. We evaluate the performance and accuracy of the new quality-of-fit analysis algorithms vis-à-vis existing tools, examine algorithm performance on GPU-accelerated desktop workstations and supercomputers, and describe new visualization techniques for results of hybrid structure fitting methods.

  6. Complete multipactor suppression in an X-band dielectric-loaded accelerating structure

    SciTech Connect

    Jing, C.; Gold, S. H.; Fischer, Richard; Gai, W.

    2016-05-09

    Multipactor is a major issue limiting the gradient of rf-driven Dielectric-Loaded Accelerating (DLA) structures. Theoretical models have predicted that an axial magnetic field applied to DLA structures may completely block the multipactor discharge. However, previous attempts to demonstrate this magnetic field effect in an X-band traveling-wave DLA structure were inconclusive, due to the axial variation of the applied magnetic field, and showed only partial suppression of the multipactor loading [Jing et al., Appl. Phys. Lett. 103, 213503 (2013)]. The present experiment has been performed under improved conditions with a uniform axial magnetic field extending along the length of an X-band standing-wave DLA structure. Multipactor loading began to be continuously reduced starting from 3.5 kG applied magnetic field and was completely suppressed at 8 kG. Dependence of multipactor suppression on the rf gradient inside the DLA structure was also measured.

  7. Acceleration ground test program to verify GAS payload No. 559 structure/support avionics and experiment structural integrity

    NASA Technical Reports Server (NTRS)

    Cassanto, John M.; Cassanto, Valerie A.

    1988-01-01

    Acceleration ground tests were conducted on the Get Away Special (GAS) payload 559 to verify the structural integrity of the structure/support avionics and two of the planned three flight experiments. The ITA (Integrated Test Area) Standardized Experiment Module (ISEM) structure was modified to accommodate the experiments for payload 559. The ISEM avionics consisted of a heavy duty sliver zinc power supply, three orthogonal-mounted low range microgravity accelerometers, a tri-axis high range accelerometer, a solid state recorder/programmer sequencer, and pressure and temperature sensors. The tests were conducted using the Gravitational Plant Physiology Laboratory Centrifuge of the University City Science Center in Philadelphia, PA. The launch-powered flight steady state acceleration profile of the shuttle was simulated from lift-off through jettison of the External Tank (3.0 g's). Additional tests were conducted at twice the nominal powered flight acceleration levels (6 g's) and an over-test condition of four times the powered flight loads to 12.6 g's. The present test program has demonstrated the value of conducting ground tests to verify GAS payload experiment integrity and operation before flying on the shuttle.

  8. Geometric dependence of radio-frequency breakdown in normal conducting accelerating structures

    SciTech Connect

    Dolgashev, Valery; Tantawi, Sami; Higashi, Yasuo; Spataro, Bruno

    2010-10-25

    We present the experimental results of a systematic study of rf breakdown phenomenon in high vacuum accelerator structures. In this study, the surface processing, geometry, and materials of the structures have been varied, one parameter at a time. The breakdown rate or alternatively, the probability of breakdown/pulse/meter has been recorded for different operating parameters. These statistical data reveal a strong dependence of breakdown probability on surface magnetic field, or alternatively on surface pulsed heating. This is in contrast to the classical view of electric field dependence. We will present our experimental methodology and results showing this remarkable correlation.

  9. Theory of factors limiting high gradient operation of warm accelerating structures

    SciTech Connect

    Nusinovich, Gregory S.; Antonsen, Thomas M.; Kishek, Rami

    2014-07-25

    This final report summarizes the research performed during the time period from 8/1/2010 to 7/31/2013. It consists of two parts describing our studies in two directions: (a) analysis of factors limiting operation of dielectric-loaded accelerating (DLA) structures where the main problem is the occurrence of multipactor on dielectric surfaces, and (b) studies of effects associated with either RF magnetic or RF electric fields which may cause the RF breakdown in high-gradient metallic accelerating structures. In the studies of DLA structures, at least, two accomplishments should be mentioned: the development of a 3D non-stationary, self-consistent code describing the multipactor phenomena and yielding very good agreement with some experimental data obtained in joint ANL/NRL experiments. In the metallic structures, such phenomena as the heating and melting of micro-particles (metallic dust) by RF electric and magnetic fields in single-shot and rep-rate regimes is analyzed. Also, such processes in micro-protrusions on the structure surfaces as heating and melting due to the field emitted current and the Nottingham effect are thoroughly investigated with the account for space charge of emitted current on the field emission from the tip.

  10. Development of a dual-layered dielectric-loaded accelerating structure

    NASA Astrophysics Data System (ADS)

    Jing, Chunguang; Kanareykin, Alexei; Kazakov, Sergey; Liu, Wanming; Nenasheva, Elizaveta; Schoessow, Paul; Gai, Wei

    2008-09-01

    rf Power attenuation is a critical problem in the development of dielectric-loaded structures for particle acceleration. In a previous paper [C. Jing, W. Liu, W. Gai, J. Power, T. Wong, Nucl. Instr. Meth. A 539 (2005) 445] we suggested the use of a Multilayer Dielectric-Loaded Accelerating Structure (MDLA) as a possible approach for reducing the rf losses in a single layer device. The MDLA is based on the principle of Bragg reflection familiar from optics that is used to partially confine the fields inside the dielectric layers and reduce the wall current losses at the outer boundary. We report here on the design, construction and testing of a prototype X-band double-layer structure (2DLA). The measurements show an rf power attenuation for the 2DLA more than ten times smaller than that of a comparable single-layer structure, in good agreement with the analytic results. Testing and operation of MDLAs also requires efficient power coupling from test equipment or rf power systems to the device. We describe the design and construction of two novel structures: a TM 03 mode launcher for cold testing and a power coupler for planned high-gradient experiments.

  11. Capturing Structural Dynamics in Crystalline Silicon Using Chirped Electrons from a Laser Wakefield Accelerator

    PubMed Central

    He, Z.-H.; Beaurepaire, B.; Nees, J. A.; Gallé, G.; Scott, S. A.; Pérez, J. R. Sánchez; Lagally, M. G.; Krushelnick, K.; Thomas, A. G. R.; Faure, J.

    2016-01-01

    Recent progress in laser wakefield acceleration has led to the emergence of a new generation of electron and X-ray sources that may have enormous benefits for ultrafast science. These novel sources promise to become indispensable tools for the investigation of structural dynamics on the femtosecond time scale, with spatial resolution on the atomic scale. Here, we demonstrate the use of laser-wakefield-accelerated electron bunches for time-resolved electron diffraction measurements of the structural dynamics of single-crystal silicon nano-membranes pumped by an ultrafast laser pulse. In our proof-of-concept study, we resolve the silicon lattice dynamics on a picosecond time scale by deflecting the momentum-time correlated electrons in the diffraction peaks with a static magnetic field to obtain the time-dependent diffraction efficiency. Further improvements may lead to femtosecond temporal resolution, with negligible pump-probe jitter being possible with future laser-wakefield-accelerator ultrafast-electron-diffraction schemes. PMID:27824086

  12. Conceptual Design of Dielectric Accelerating Structures for Intense Neutron and Monochromatic X-ray Sources

    SciTech Connect

    Blanovsky, Anatoly

    2004-12-07

    Bright compact photon sources, which utilize electron beam interaction with periodic structures, may benefit a broad range of medical, industrial and scientific applications. A class of dielectric-loaded periodic structures for hard and soft X-ray production has been proposed that would provide a high accelerating gradient when excited by an external RF and/or primary electron beam. Target-distributed accelerators (TDA), in which an additional electric field compensates for lost beam energy in internal targets, have been shown to provide the necessary means to drive a high flux subcritical reactor (HFSR) for nuclear waste transmutation. The TDA may also be suitable for positron and nuclear isomer production, X-ray lithography and monochromatic computer tomography. One of the early assumptions of the theory of dielectric wake-field acceleration was that, in electrodynamics, the vector potential was proportional to the scalar potential. The analysis takes into consideration a wide range of TDA design aspects including the wave model of observed phenomena, a layered compound separated by a Van der Waals gap and a compact energy source based on fission electric cells (FEC) with a multistage collector. The FEC is a high-voltage power source that directly converts the kinetic energy of the fission fragments into electrical potential of about 2MV.

  13. Structural Basis for Accelerated Cleavage of Bovine Pancreatic Trypsin Inhibitor (BPTI) by Human Mesotrypsin

    SciTech Connect

    Salameh,M.; Soares, A.; Hockla, A.; Radisky, E.

    2008-01-01

    Human mesotrypsin is an isoform of trypsin that displays unusual resistance to polypeptide trypsin inhibitors and has been observed to cleave several such inhibitors as substrates. Whereas substitution of arginine for the highly conserved glycine 193 in the trypsin active site has been implicated as a critical factor in the inhibitor resistance of mesotrypsin, how this substitution leads to accelerated inhibitor cleavage is not clear. Bovine pancreatic trypsin inhibitor (BPTI) forms an extremely stable and cleavage-resistant complex with trypsin, and thus provides a rigorous challenge of mesotrypsin catalytic activity toward polypeptide inhibitors. Here, we report kinetic constants for mesotrypsin and the highly homologous (but inhibitor sensitive) human cationic trypsin, describing inhibition by, and cleavage of BPTI, as well as crystal structures of the mesotrypsin-BPTI and human cationic trypsin-BPTI complexes. We find that mesotrypsin cleaves BPTI with a rate constant accelerated 350-fold over that of human cationic trypsin and 150,000-fold over that of bovine trypsin. From the crystal structures, we see that small conformational adjustments limited to several side chains enable mesotrypsin-BPTI complex formation, surmounting the predicted steric clash introduced by Arg-193. Our results show that the mesotrypsin-BPTI interface favors catalysis through (a) electrostatic repulsion between the closely spaced mesotrypsin Arg-193 and BPTI Arg-17, and (b) elimination of two hydrogen bonds between the enzyme and the amine leaving group portion of BPTI. Our model predicts that these deleterious interactions accelerate leaving group dissociation and deacylation.

  14. FPGA accelerator for protein secondary structure prediction based on the GOR algorithm

    PubMed Central

    2011-01-01

    Background Protein is an important molecule that performs a wide range of functions in biological systems. Recently, the protein folding attracts much more attention since the function of protein can be generally derived from its molecular structure. The GOR algorithm is one of the most successful computational methods and has been widely used as an efficient analysis tool to predict secondary structure from protein sequence. However, the execution time is still intolerable with the steep growth in protein database. Recently, FPGA chips have emerged as one promising application accelerator to accelerate bioinformatics algorithms by exploiting fine-grained custom design. Results In this paper, we propose a complete fine-grained parallel hardware implementation on FPGA to accelerate the GOR-IV package for 2D protein structure prediction. To improve computing efficiency, we partition the parameter table into small segments and access them in parallel. We aggressively exploit data reuse schemes to minimize the need for loading data from external memory. The whole computation structure is carefully pipelined to overlap the sequence loading, computing and back-writing operations as much as possible. We implemented a complete GOR desktop system based on an FPGA chip XC5VLX330. Conclusions The experimental results show a speedup factor of more than 430x over the original GOR-IV version and 110x speedup over the optimized version with multi-thread SIMD implementation running on a PC platform with AMD Phenom 9650 Quad CPU for 2D protein structure prediction. However, the power consumption is only about 30% of that of current general-propose CPUs. PMID:21342582

  15. Numerical simulations of input and output couplers for linear accelerator structures

    SciTech Connect

    Ng, C.K.; Ko, K.

    1993-04-01

    We present the numerical procedures involved in the design of coupler cavities for accelerator sections for linear colliders. The MAFIA code is used to simulate an X-band accelerator section with a symmetrical double-input coupler at each end. The transmission properties of the structure are calculated in the time domain and the dimensions of the coupler cavities are adjusted until the power coupling is optimized and frequency synchronism is obtained. We compare the performance of the symmetrical double-input design with that of the conventional single-input type by evaluating the field amplitude and phase asymmetries. We also evaluate the peak gradient in the coupler and discuss the implication of pulse rise time on dark current generation.

  16. Numerical simulations of input and output couplers for linear accelerator structures

    SciTech Connect

    Ng, C.; Ko, K. )

    1993-12-25

    We present the numerical procedures involved in the design of coupler cavities for accelerator sections for linear colliders. The MAFIA code is used to simulate an X-band accelerator section with a symmetrical double-input coupler at each end. The transmissions properties of the structure are calculated in the time domain and the dimensions of the coupler cavities are adjusted until the power coupling is optimized and frequency synchronism is obtained. We compare the performance of the symmetrical double-input design with that of the conventional single-input type by evaluating the field amplitude and phase asymmetries. We also evaluate the peak gradient in the coupler and discuss the implication of pulse rise time on dark current generation.

  17. Measurements of ultimate accelerating gradients in the SLAC disk-loaded structure

    SciTech Connect

    Wang, J.W.; Loew, G.A.

    1985-03-01

    This paper is a status report on an on-going program at SLAC to study accelerator structures under high-gradient electric field conditions. The study is a part of a much broader program dealing with future linear colliders. The accelerating gradient that might be achievable in such machines is a crucial parameter because once the beam energy is selected, the gradient determines the length of the linac and directly or indirectly affects the choice of many other parameters. To reach 100 MV/m in a conventional 3 m constant-gradient section without SLED, one would need a klystron with a peak power output of 900 MW. Since such a tube is not available, we decided to use a short standing-wave section in which the resonant fields can build up. The design criteria for this section, the fabrication, matching and tuning, the experimental set-up and the results are described. 6 refs., 5 figs., 1 tab.

  18. Spectroscopic characterization of the oligomeric surface structures on polyamide materials formed during accelerated aging.

    PubMed

    Chernev, Boril S; Eder, Gabriele C

    2011-10-01

    Crystalline surface species were observed at the surface of polyamide 12 materials upon accelerated aging. After detection of the depositions with scanning electron microscopy (SEM), the crystalline surface precipitations were analyzed with Fourier transform infrared (FT-IR) and Raman imaging microscopy. These surface species were supposed to be cyclic oligomers (dimer and trimer) of the PA12 monomer laurolactam, which are usually present in polyamide materials and tend to migrate to the surface when the material is subjected to accelerated aging. The evidence for the chemical identity of the crystalline surface structures to be mainly the cyclic dimer and trimer of laurolactam was given by melting-point identification and mass spectroscopic analysis of the methanol eluate of the surface. The Raman and FT-IR spectra of the mixture were extracted from the recorded images.

  19. Recent Progress in R& D of Advanced Room Temperature Accelerator Structures

    SciTech Connect

    Wang, Juwen

    2003-08-11

    The NLC and JLC groups face two major challenges in designing X-Band accelerator structures for an electron-positron linear collider. The first is to demonstrate stable, long-term operation at a 70 MV/m gradient, which is required to keep the machine cost low, and the second is to strongly suppress the structure long-range wakefield, which is required to achieve high luminosity. During the past 2 years, the major emphasis has been on proving high gradient operation, although dipole wakefield suppression studies are continuing. This paper describes high gradient test results from a series of prototype TW and SW structures being developed for the NLC/JLC. Schemes for damping and detuning the dipole modes of these structures are also presented.

  20. Experimental high gradient testing of a 17.1 GHz photonic band-gap accelerator structure

    NASA Astrophysics Data System (ADS)

    Munroe, Brian J.; Zhang, JieXi; Xu, Haoran; Shapiro, Michael A.; Temkin, Richard J.

    2016-03-01

    We report the design, fabrication, and high gradient testing of a 17.1 GHz photonic band-gap (PBG) accelerator structure. Photonic band-gap (PBG) structures are promising candidates for electron accelerators capable of high-gradient operation because they have the inherent damping of high order modes required to avoid beam breakup instabilities. The 17.1 GHz PBG structure tested was a single cell structure composed of a triangular array of round copper rods of radius 1.45 mm spaced by 8.05 mm. The test assembly consisted of the test PBG cell located between conventional (pillbox) input and output cells, with input power of up to 4 MW from a klystron supplied via a TM01 mode launcher. Breakdown at high gradient was observed by diagnostics including reflected power, downstream and upstream current monitors and visible light emission. The testing procedure was first benchmarked with a conventional disc-loaded waveguide structure, which reached a gradient of 87 MV /m at a breakdown probability of 1.19 ×10-1 per pulse per meter. The PBG structure was tested with 100 ns pulses at gradient levels of less than 90 MV /m in order to limit the surface temperature rise to 120 K. The PBG structure reached up to 89 MV /m at a breakdown probability of 1.09 ×10-1 per pulse per meter. These test results show that a PBG structure can simultaneously operate at high gradients and low breakdown probability, while also providing wakefield damping.

  1. Rapid analysis of scattering from periodic dielectric structures using accelerated Cartesian expansions

    DOE PAGES

    Baczewski, Andrew David; Miller, Nicholas C.; Shanker, Balasubramaniam

    2012-03-22

    Here, the analysis of fields in periodic dielectric structures arise in numerous applications of recent interest, ranging from photonic bandgap structures and plasmonically active nanostructures to metamaterials. To achieve an accurate representation of the fields in these structures using numerical methods, dense spatial discretization is required. This, in turn, affects the cost of analysis, particularly for integral-equation-based methods, for which traditional iterative methods require Ο(Ν2) operations, Ν being the number of spatial degrees of freedom. In this paper, we introduce a method for the rapid solution of volumetric electric field integral equations used in the analysis of doubly periodic dielectricmore » structures. The crux of our method is the accelerated Cartesian expansion algorithm, which is used to evaluate the requisite potentials in Ο(Ν) cost. Results are provided that corroborate our claims of acceleration without compromising accuracy, as well as the application of our method to a number of compelling photonics applications.« less

  2. Accelerated cryo-EM structure determination with parallelisation using GPUs in RELION-2

    PubMed Central

    Kimanius, Dari; Forsberg, Björn O; Scheres, Sjors HW; Lindahl, Erik

    2016-01-01

    By reaching near-atomic resolution for a wide range of specimens, single-particle cryo-EM structure determination is transforming structural biology. However, the necessary calculations come at large computational costs, which has introduced a bottleneck that is currently limiting throughput and the development of new methods. Here, we present an implementation of the RELION image processing software that uses graphics processors (GPUs) to address the most computationally intensive steps of its cryo-EM structure determination workflow. Both image classification and high-resolution refinement have been accelerated more than an order-of-magnitude, and template-based particle selection has been accelerated well over two orders-of-magnitude on desktop hardware. Memory requirements on GPUs have been reduced to fit widely available hardware, and we show that the use of single precision arithmetic does not adversely affect results. This enables high-resolution cryo-EM structure determination in a matter of days on a single workstation. DOI: http://dx.doi.org/10.7554/eLife.18722.001 PMID:27845625

  3. Accelerating Content-Based Image Retrieval via GPU-Adaptive Index Structure

    PubMed Central

    2014-01-01

    A tremendous amount of work has been conducted in content-based image retrieval (CBIR) on designing effective index structure to accelerate the retrieval process. Most of them improve the retrieval efficiency via complex index structures, and few take into account the parallel implementation of them on underlying hardware, making the existing index structures suffer from low-degree of parallelism. In this paper, a novel graphics processing unit (GPU) adaptive index structure, termed as plane semantic ball (PSB), is proposed to simultaneously reduce the work of retrieval process and exploit the parallel acceleration of underlying hardware. In PSB, semantics are embedded into the generation of representative pivots and multiple balls are selected to cover more informative reference features. With PSB, the online retrieval of CBIR is factorized into independent components that are implemented on GPU efficiently. Comparative experiments with GPU-based brute force approach demonstrate that the proposed approach can achieve high speedup with little information loss. Furthermore, PSB is compared with the state-of-the-art approach, random ball cover (RBC), on two standard image datasets, Corel 10 K and GIST 1 M. Experimental results show that our approach achieves higher speedup than RBC on the same accuracy level. PMID:24782668

  4. rf breakdown measurements in electron beam driven 200 GHz copper and copper-silver accelerating structures

    DOE PAGES

    Dal Forno, Massimo; Dolgashev, Valery; Bowden, Gordon; ...

    2016-11-30

    This study explores the physics of vacuum rf breakdowns in subterahertz high-gradient traveling-wave accelerating structures. We present the experimental results of rf tests of 200 GHz metallic accelerating structures, made of copper and copper-silver. These experiments were carried out at the Facility for Advanced Accelerator Experimental Tests (FACET) at the SLAC National Accelerator Laboratory. The rf fields were excited by the FACET ultrarelativistic electron beam. The traveling-wave structure is an open geometry, 10 cm long, composed of two halves separated by a gap. The rf frequency of the fundamental accelerating mode depends on the gap size and can be changedmore » from 160 to 235 GHz. When the beam travels off axis, a deflecting field is induced in addition to the longitudinal field. We measure the deflecting forces by observing the displacement of the electron bunch and use this measurement to verify the expected accelerating gradient. Furthermore, we present the first quantitative measurement of rf breakdown rates in 200 GHz metallic accelerating structures. The breakdown rate of the copper structure is 10–2 per pulse, with a peak surface electric field of 500 MV/m and a rf pulse length of 0.3 ns, which at a relatively large gap of 1.5 mm, or one wavelength, corresponds to an accelerating gradient of 56 MV/m. For the same breakdown rate, the copper-silver structure has a peak electric field of 320 MV/m at a pulse length of 0.5 ns. For a gap of 1.1 mm, or 0.74 wavelengths, this corresponds to an accelerating gradient of 50 MV/m.« less

  5. Fine-grained parallelism accelerating for RNA secondary structure prediction with pseudoknots based on FPGA.

    PubMed

    Xia, Fei; Jin, Guoqing

    2014-06-01

    PKNOTS is a most famous benchmark program and has been widely used to predict RNA secondary structure including pseudoknots. It adopts the standard four-dimensional (4D) dynamic programming (DP) method and is the basis of many variants and improved algorithms. Unfortunately, the O(N(6)) computing requirements and complicated data dependency greatly limits the usefulness of PKNOTS package with the explosion in gene database size. In this paper, we present a fine-grained parallel PKNOTS package and prototype system for accelerating RNA folding application based on FPGA chip. We adopted a series of storage optimization strategies to resolve the "Memory Wall" problem. We aggressively exploit parallel computing strategies to improve computational efficiency. We also propose several methods that collectively reduce the storage requirements for FPGA on-chip memory. To the best of our knowledge, our design is the first FPGA implementation for accelerating 4D DP problem for RNA folding application including pseudoknots. The experimental results show a factor of more than 50x average speedup over the PKNOTS-1.08 software running on a PC platform with Intel Core2 Q9400 Quad CPU for input RNA sequences. However, the power consumption of our FPGA accelerator is only about 50% of the general-purpose micro-processors.

  6. Dipole-mode wakefields in dielectric-loaded rectangular waveguide accelerating structures.

    PubMed

    Jing, Chunguang; Liu, Wanming; Xiao, Liling; Gai, Wei; Schoessow, P; Wong, Thomas

    2003-07-01

    By applying different symmetric boundary conditions, we found that the transverse wakefields generated by an electron bunch traveling through a partially loaded rectangular dielectric structure at an off center position can be decomposed into corresponding orthogonal longitudinal section electric (LSE) and longitudinal section magnetic (LSM) modes for guided waves as in the case of longitudinal wakefields treated previously. The wakefields are characterized using the normalized shunt impedance R/Q, a function of the geometry of the accelerating structure, for both LSE and LSM modes. A numerical example is given for an X-band waveguide structure and detailed results are given for the several leading transverse wakefield terms. The analytic results obtained are in agreement with the results from the time domain simulation tool MAFIA.

  7. Dipole-mode wakefields in dielectric-loaded rectangular waveguide accelerating structures

    NASA Astrophysics Data System (ADS)

    Jing, Chunguang; Liu, Wanming; Xiao, Liling; Gai, Wei; Schoessow, P.; Wong, Thomas

    2003-07-01

    By applying different symmetric boundary conditions, we found that the transverse wakefields generated by an electron bunch traveling through a partially loaded rectangular dielectric structure at an off center position can be decomposed into corresponding orthogonal longitudinal section electric (LSE) and longitudinal section magnetic (LSM) modes for guided waves as in the case of longitudinal wakefields treated previously. The wakefields are characterized using the normalized shunt impedance R/Q, a function of the geometry of the accelerating structure, for both LSE and LSM modes. A numerical example is given for an X-band waveguide structure and detailed results are given for the several leading transverse wakefield terms. The analytic results obtained are in agreement with the results from the time domain simulation tool MAFIA®.

  8. Transverse operator method for wakefields in a rectangular dielectric loaded accelerating structure

    NASA Astrophysics Data System (ADS)

    Baturin, S. S.; Sheinman, I. L.; Altmark, A. M.; Kanareykin, A. D.

    2013-05-01

    Cherenkov radiation generated by a relativistic electron bunch in a rectangular dielectric-loaded waveguide is analyzed under the assumption that the dielectric layers are inhomogeneous normal to the beam path. We propose a method that uses eigenfunctions of the transverse operator applied to develop a rigorous full solution for the wakefields that are generated. The dispersion equation for the structure is derived and the wakefield analysis is carried out. The formalism developed here allows the direct solution of the inhomogeneous system of Maxwell equations, an alternative analytic approach to the analysis of wakefields in contrast to the previously used impedance method for rectangular structure analysis. The formalism described here was successfully applied to the analysis of rectangular dielectric-lined structures that have been recently beam tested at the Argonne (ANL/AWA) and Brookhaven (BNL/ATF) accelerator facilities.

  9. Accelerating adiabatic quantum transfer for three-level Λ-type structure systems via picture transformation

    NASA Astrophysics Data System (ADS)

    Kang, Yi-Hao; Wu, Qi-Cheng; Chen, Ye-Hong; Shi, Zhi-Cheng; Song, Jie; Xia, Yan

    2017-04-01

    In this paper, we investigate the quantum transfer for the system with three-level Λ-type structure, and construct a shortcut to the adiabatic passage via picture transformation to speed up the evolution. We can design the pulses directly without any additional couplings. Moreover, by choosing suitable control parameters, the Rabi frequencies of pulses can be expressed by the linear superpositions of Gaussian functions, which could be easily realized in experiments. Compared with the previous works using the stimulated Raman adiabatic passage, the quantum transfer can be significantly accelerated with the present scheme.

  10. The ANL experiment for a wake field accelerator using an rf structure

    SciTech Connect

    Ruggiero, A.G.; Schoessow, P.; Simpson, J.

    1986-08-27

    Experiments are planned at ANL to study a new accelerating concept that has been developed during the last few years named the WAKEATRON. This requires a very special, simple configuration of the beams and of the rf structure involved. The basic concepts are explained. Like most proposed experimental work, this too was initiated by a considerable amount of computational work, both analytical and numerical, on which we would like to report. We will then describe details of the planned experiments we will carry out at ANL to check some of our predictions for this concept. These experiments concentrate on beam and cavity geometry applicable to the Wakeatron.

  11. Accelerated discovery of two crystal structure types in a complex inorganic phase field

    NASA Astrophysics Data System (ADS)

    Collins, C.; Dyer, M. S.; Pitcher, M. J.; Whitehead, G. F. S.; Zanella, M.; Mandal, P.; Claridge, J. B.; Darling, G. R.; Rosseinsky, M. J.

    2017-06-01

    The discovery of new materials is hampered by the lack of efficient approaches to the exploration of both the large number of possible elemental compositions for such materials, and of the candidate structures at each composition. For example, the discovery of inorganic extended solid structures has relied on knowledge of crystal chemistry coupled with time-consuming materials synthesis with systematically varied elemental ratios. Computational methods have been developed to guide synthesis by predicting structures at specific compositions and predicting compositions for known crystal structures, with notable successes. However, the challenge of finding qualitatively new, experimentally realizable compounds, with crystal structures where the unit cell and the atom positions within it differ from known structures, remains for compositionally complex systems. Many valuable properties arise from substitution into known crystal structures, but materials discovery using this approach alone risks both missing best-in-class performance and attempting design with incomplete knowledge. Here we report the experimental discovery of two structure types by computational identification of the region of a complex inorganic phase field that contains them. This is achieved by computing probe structures that capture the chemical and structural diversity of the system and whose energies can be ranked against combinations of currently known materials. Subsequent experimental exploration of the lowest-energy regions of the computed phase diagram affords two materials with previously unreported crystal structures featuring unusual structural motifs. This approach will accelerate the systematic discovery of new materials in complex compositional spaces by efficiently guiding synthesis and enhancing the predictive power of the computational tools through expansion of the knowledge base underpinning them.

  12. Uniform Plasma Etching of Complex Shaped Three Dimensional Niobium Structures for Particle Accelerators

    NASA Astrophysics Data System (ADS)

    Upadhyay, Janardan; Im, Do; Peshl, Jeremy; Popovic, Svetozar; Vuskovic, Lepsha; Phillips, Larry; Valente-Felliciano, Anne-Marie

    2014-10-01

    Complex shaped three dimensional niobium structures are used in particle accelerators as super conducting radio frequency (SRF) cavities. The inner surfaces of these structures have to be chemically etched for better performance, as SRF performance parameters are very sensitive to their properties. Plasma etching of inner surface of three dimensional niobium structures has not been reported even though plasma etching of niobium has been reported earlier for Josephson junction and other applications. We are proposing an RF capacitively coupled coaxial (ccp) plasma etching method for nano machining of niobium structures for SRF applications. We are using gas mixture of Argon and Chlorine. We report the effects of the pressure, RF power, gas concentration, shape and size of the inner electrode, temperature of the structure, DC bias voltage and residence time on the etch rate of the niobium. We also show the method to reduce the asymmetry effect in coaxial ccp by changing the shape of the inner electrode in cylindrical structure, as well as a method to overcome the severe loading effect in etching of 3D structures for uniform mass removal purpose. Supported by DOE under Grant No. DE-SC0007879. J.U. acknowledges support by JSA/DOE via DE-AC05-06OR23177.

  13. Modifying the Target Normal Sheath Accelerated Ion Spectrum Using Structured Targets

    NASA Astrophysics Data System (ADS)

    George, Kevin Mitchell

    In the interaction of high intensity (> 1018 W/cm2), ultrashort (< 1 ps) laser pulses with solid targets, the laser couples energy into the target through a population of energetic electrons. An electrostatic sheath field is formed along the target surface due to the induced charge separation between the expanding energetic electron cloud and relatively heavy, slow ions. This electrostatic field is capable of accelerating ions to energies greater than 10 MeV/nucleon through the physical mechanism known as target normal sheath acceleration (TNSA). Since its discovery in 2000, TNSA has been widely studied throughout the High Energy Density Physics community in order to understand and enhance this process for its potential applications ranging from cancer therapy to radiography. However, much of this work has been conducted on thin (1s to 10s of microns thick) metal foils exploring optimization only through critical laser parameters such as intensity, energy, and prepulse. This thesis addresses the development of novel micro-structured targets for the enhancement of TNSA ions. These targets were developed through the use of optical lithography techniques to pattern micron-scale structures onto thin substrates at the OSU Nanosystem Laboratory (NSL) user facility. These targets permit on-demand patterning of designs with 1 mum lateral resolution, heights varying between 0.5-2 mum, on substrates ranging from 0.5-2 mum thick with high throughput. An experiment was conducted at the Scarlet laser facility to characterize the effect of structuring the laser-target interface on the energy spectrum of TNSA protons. A comparison of the proton dose from structured versus at photoresist on silicon nitride substrates was performed. Results obtained using radiochromic film demonstrate an increase in proton dose by a factor of 2.3 through the use of structured photoresist as compared to unstructured photoresist of the same thickness. Two dimensional absorption simulations were

  14. Acceleration of solar wind ions to 1 MeV by electromagnetic structures upstream of the Earth's bow shock

    NASA Astrophysics Data System (ADS)

    Stasiewicz, K.; Markidis, S.; Eliasson, B.; Strumik, M.; Yamauchi, M.

    2013-05-01

    We present measurements from the ESA/NASA Cluster mission that show in situ acceleration of ions to energies of 1 MeV outside the bow shock. The observed heating can be associated with the presence of electromagnetic structures with strong spatial gradients of the electric field that lead to ion gyro-phase breaking and to the onset of chaos in ion trajectories. It results in rapid, stochastic acceleration of ions in the direction perpendicular to the ambient magnetic field. The electric potential of the structures can be compared to a field of moguls on a ski slope, capable of accelerating and ejecting the fast running skiers out of piste. This mechanism may represent the universal mechanism for perpendicular acceleration and heating of ions in the magnetosphere, the solar corona and in astrophysical plasmas. This is also a basic mechanism that can limit steepening of nonlinear electromagnetic structures at shocks and foreshocks in collisionless plasmas.

  15. GeauxDock: Accelerating Structure-Based Virtual Screening with Heterogeneous Computing

    PubMed Central

    Fang, Ye; Ding, Yun; Feinstein, Wei P.; Koppelman, David M.; Moreno, Juana; Jarrell, Mark; Ramanujam, J.; Brylinski, Michal

    2016-01-01

    Computational modeling of drug binding to proteins is an integral component of direct drug design. Particularly, structure-based virtual screening is often used to perform large-scale modeling of putative associations between small organic molecules and their pharmacologically relevant protein targets. Because of a large number of drug candidates to be evaluated, an accurate and fast docking engine is a critical element of virtual screening. Consequently, highly optimized docking codes are of paramount importance for the effectiveness of virtual screening methods. In this communication, we describe the implementation, tuning and performance characteristics of GeauxDock, a recently developed molecular docking program. GeauxDock is built upon the Monte Carlo algorithm and features a novel scoring function combining physics-based energy terms with statistical and knowledge-based potentials. Developed specifically for heterogeneous computing platforms, the current version of GeauxDock can be deployed on modern, multi-core Central Processing Units (CPUs) as well as massively parallel accelerators, Intel Xeon Phi and NVIDIA Graphics Processing Unit (GPU). First, we carried out a thorough performance tuning of the high-level framework and the docking kernel to produce a fast serial code, which was then ported to shared-memory multi-core CPUs yielding a near-ideal scaling. Further, using Xeon Phi gives 1.9× performance improvement over a dual 10-core Xeon CPU, whereas the best GPU accelerator, GeForce GTX 980, achieves a speedup as high as 3.5×. On that account, GeauxDock can take advantage of modern heterogeneous architectures to considerably accelerate structure-based virtual screening applications. GeauxDock is open-sourced and publicly available at www.brylinski.org/geauxdock and https://figshare.com/articles/geauxdock_tar_gz/3205249. PMID:27420300

  16. GeauxDock: Accelerating Structure-Based Virtual Screening with Heterogeneous Computing.

    PubMed

    Fang, Ye; Ding, Yun; Feinstein, Wei P; Koppelman, David M; Moreno, Juana; Jarrell, Mark; Ramanujam, J; Brylinski, Michal

    2016-01-01

    Computational modeling of drug binding to proteins is an integral component of direct drug design. Particularly, structure-based virtual screening is often used to perform large-scale modeling of putative associations between small organic molecules and their pharmacologically relevant protein targets. Because of a large number of drug candidates to be evaluated, an accurate and fast docking engine is a critical element of virtual screening. Consequently, highly optimized docking codes are of paramount importance for the effectiveness of virtual screening methods. In this communication, we describe the implementation, tuning and performance characteristics of GeauxDock, a recently developed molecular docking program. GeauxDock is built upon the Monte Carlo algorithm and features a novel scoring function combining physics-based energy terms with statistical and knowledge-based potentials. Developed specifically for heterogeneous computing platforms, the current version of GeauxDock can be deployed on modern, multi-core Central Processing Units (CPUs) as well as massively parallel accelerators, Intel Xeon Phi and NVIDIA Graphics Processing Unit (GPU). First, we carried out a thorough performance tuning of the high-level framework and the docking kernel to produce a fast serial code, which was then ported to shared-memory multi-core CPUs yielding a near-ideal scaling. Further, using Xeon Phi gives 1.9× performance improvement over a dual 10-core Xeon CPU, whereas the best GPU accelerator, GeForce GTX 980, achieves a speedup as high as 3.5×. On that account, GeauxDock can take advantage of modern heterogeneous architectures to considerably accelerate structure-based virtual screening applications. GeauxDock is open-sourced and publicly available at www.brylinski.org/geauxdock and https://figshare.com/articles/geauxdock_tar_gz/3205249.

  17. Methodology for the structural design of single spoke accelerating cavities at Fermilab

    DOE PAGES

    Passarelli, Donato; Wands, Robert H.; Merio, Margherita; ...

    2016-10-01

    Fermilab is planning to upgrade its accelerator complex to deliver a more powerful and intense proton-beam for neutrino experiments. In the framework of the so-called Proton Improvement Plan-II (PIP-II), we are designing and developing a cryomodule containing superconducting accelerating cavities, the Single Spoke Resonators of type 1 (SSR1). In this paper, we present the sequence of analysis and calculations performed for the structural de- sign of these cavities, using the rules of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC). The lack of an accepted procedure for addressing the design, fabrication, and inspection of suchmore » unique pressure vessels makes the task demanding and challenging every time. Several factors such as exotic materials, unqualified brazing procedures, limited nondestructive examination, and the general R&D nature of these early generations of cavity design, conspire to make it impractical to obtain full compliance with all ASME BPVC requirements. However, the presented approach allowed us to validate the design of these new generation of single spoke cavities with values of maximum allowable working pressure that exceed the safety requirements. This set of rules could be used as a starting point for the structural design and development of similar objects.« less

  18. Methodology for the structural design of single spoke accelerating cavities at Fermilab

    SciTech Connect

    Passarelli, Donato; Wands, Robert H.; Merio, Margherita; Ristori, Leonardo

    2016-10-01

    Fermilab is planning to upgrade its accelerator complex to deliver a more powerful and intense proton-beam for neutrino experiments. In the framework of the so-called Proton Improvement Plan-II (PIP-II), we are designing and developing a cryomodule containing superconducting accelerating cavities, the Single Spoke Resonators of type 1 (SSR1). In this paper, we present the sequence of analysis and calculations performed for the structural de- sign of these cavities, using the rules of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC). The lack of an accepted procedure for addressing the design, fabrication, and inspection of such unique pressure vessels makes the task demanding and challenging every time. Several factors such as exotic materials, unqualified brazing procedures, limited nondestructive examination, and the general R&D nature of these early generations of cavity design, conspire to make it impractical to obtain full compliance with all ASME BPVC requirements. However, the presented approach allowed us to validate the design of these new generation of single spoke cavities with values of maximum allowable working pressure that exceed the safety requirements. This set of rules could be used as a starting point for the structural design and development of similar objects.

  19. Methodology for the structural design of single spoke accelerating cavities at Fermilab

    SciTech Connect

    Passarelli, Donato; Wands, Robert H.; Merio, Margherita; Ristori, Leonardo

    2016-10-01

    Fermilab is planning to upgrade its accelerator complex to deliver a more powerful and intense proton-beam for neutrino experiments. In the framework of the so-called Proton Improvement Plan-II (PIP-II), we are designing and developing a cryomodule containing superconducting accelerating cavities, the Single Spoke Resonators of type 1 (SSR1). In this paper, we present the sequence of analysis and calculations performed for the structural de- sign of these cavities, using the rules of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC). The lack of an accepted procedure for addressing the design, fabrication, and inspection of such unique pressure vessels makes the task demanding and challenging every time. Several factors such as exotic materials, unqualified brazing procedures, limited nondestructive examination, and the general R&D nature of these early generations of cavity design, conspire to make it impractical to obtain full compliance with all ASME BPVC requirements. However, the presented approach allowed us to validate the design of these new generation of single spoke cavities with values of maximum allowable working pressure that exceed the safety requirements. This set of rules could be used as a starting point for the structural design and development of similar objects.

  20. High gradient, high reliability, and low wakefield accelerating structures for the FERMI FEL

    NASA Astrophysics Data System (ADS)

    Serpico, Claudio; Shafqat, Nuaman; Grudiev, Alexej; Vescovo, Roberto

    2017-07-01

    The FERMI seeded free-electron laser (FEL), located at the Elettra laboratory in Trieste, is a 4th generation light source operating in the vacuum ultraviolet to soft X-rays range. The FEL design is based on an external seeding scheme which improves the output pulse coherence and the central wavelength control and reduces the spectral bandwidth. FERMI has achieved its original energy target by producing photon energies above 300 eV from a 1.50 GeV, 600 A peak current, electron beam. However, there is a strong scientific motivation to push the energy envelop further higher to photon energy up to 600 eV to cover both the x-ray absorption edges of nitrogen K (400 eV) and oxygen K (532 eV). To achieve this goal, the electron beam energy will be increased from 1.50 GeV to 1.80 GeV and the peak beam current will be pushed towards 1 kA. This requires essentially the development of more reliable high gradient S-band accelerating structures, with low wakefields contribution up to 1 nC charge per bunch. Accordingly, in the following, we present the design of high gradient, high reliability, and low wakefield S-band accelerating structures for the upgrade program of the FERMI linac.

  1. Methodology for the structural design of single spoke accelerating cavities at Fermilab

    NASA Astrophysics Data System (ADS)

    Passarelli, Donato; Wands, Robert H.; Merio, Margherita; Ristori, Leonardo

    2016-10-01

    Fermilab is planning to upgrade its accelerator complex to deliver a more powerful and intense proton-beam for neutrino experiments. In the framework of the so-called Proton Improvement Plan-II (PIP-II), we are designing and developing a cryomodule containing superconducting accelerating cavities, the Single Spoke Resonators of type 1 (SSR1). In this paper, we present the sequence of analysis and calculations performed for the structural design of these cavities, using the rules of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC). The lack of an accepted procedure for addressing the design, fabrication, and inspection of such unique pressure vessels makes the task demanding and challenging every time. Several factors such as exotic materials, unqualified brazing procedures, limited nondestructive examination, and the general R&D nature of these early generations of cavity design, conspire to make it impractical to obtain full compliance with all ASME BPVC requirements. However, the presented approach allowed us to validate the design of this new generation of single spoke cavities with values of maximum allowable working pressure that exceeds the safety requirements. This set of rules could be used as a starting point for the structural design and development of similar objects.

  2. A fast "kicker" using a two-channel rectangular dielectric wakefield accelerator structure

    NASA Astrophysics Data System (ADS)

    Marshall, Thomas C.; Shchelkunov, Sergey V.; Sotnikov, Gennadij V.; Hirshfield, Jay L.

    2017-03-01

    A method is proposed to select and eject bunches of electrons or positrons from a high energy train of charged bunches, based on proven dielectric wakefield accelerator technology. The kicker structure, consisting of a pair of adjacent rectangular dielectric-lined waveguides, permits the coupling of the wakefield that is generated from a train of low-energy (˜6 MeV) "drive bunches" moving in one waveguide to the adjacent waveguide where a portion of a train of high energy "witness bunches" needs to be diverted. A very fast response time (˜1 ns) for bunch deflection is estimated, and a structure as short as 10-30 cm would suffice to impart to the diverted bunches a transverse kick of an interest to high-energy accelerator application, e.g. 150 keV/c. The witness bunch width must be less than 0.2 - 0.3 mm to have an emittance dilution that makes the deflected bunch suitable for e.g. FEL applications.

  3. Annular structures formed in a beam of ions during their collective acceleration in a system with dielectric anode

    NASA Astrophysics Data System (ADS)

    Lopatin, V. S.; Remnev, G. E.; Martynenko, A. A.

    2017-05-01

    We have studied the collective acceleration of protons and deuterons in an electron beam emitted from plasma formed at the surface of a dielectric anode insert. The experiments were performed with a pulsed electron accelerator operating at an accelerating voltage up to 1 MV, current amplitude up to 40 kA, and pulse duration of 50 ns. Reduction of the accelerating voltage pulse front width and optimization of the diode unit and drift region ensured the formation of several annular structures in the electron beam. As a result, up to 50% of the radioactivity induced in a copper target was concentrated in a ring with 4.5-cm diameter and 0.2-cm width. The formation of high energy density in these circular traces and the appearance of an axial component of the self-generated magnetic field of the electron beam are related with the increasing efficiency of acceleration of the most intense group of ions.

  4. Fabrication Technologies of the High Gradient Accelerator Structures at 100MV/M Range

    SciTech Connect

    Wang, Juwen; Lewandowski, James; Van Pelt, John; Yoneda, Charles; Gudkov, Boris; Riddone, Germana; Higo, Toshiyasu; Takatomi, Toshikazu; /KEK, Tsukuba

    2012-07-03

    A CERN-SLAC-KEK collaboration on high gradient X-band structure research has been established in order to demonstrate the feasibility of the CLIC baseline design for the main linac stably operating at more than 100 MV/m loaded accelerating gradient. Several prototype CLIC structures were successfully fabricated and high power tested. They operated at 105 MV/m with a breakdown rate that meets the CLIC linear collider specifications of < 5 x 10{sup -7}/pulse/m. This paper summarizes the fabrication technologies including the mechanical design, precision machining, chemical cleaning, diffusion bonding as well as vacuum baking and all related assembly technologies. Also, the tolerances control, tuning and RF characterization will be discussed.

  5. Using the k-d Tree Data Structure to Accelerate Monte Carlo Simulations.

    PubMed

    Chen, Qile P; Xue, Bai; Siepmann, J Ilja

    2017-04-11

    The k-d tree data structure is implemented in a Monte Carlo (MC) molecular simulation program to accelerate the range search for particles or interaction sites within the cutoff distance when Lennard-Jones and Coulomb interactions are computed. MC simulations are performed for different molecules in various ensembles to assess the efficiency enhancements due to the k-d tree data structure. It is found that the use of k-d trees accelerates significantly simulations for Lennard-Jones particles in the NVT and NVT-Gibbs ensembles and for n-butane and 2,4,6,8,10,12,14,16,18,20,22-undecamethylpentacosane represented by the TraPPE-UA force field in the NpT ensemble. Simulations for TraPPE-UA ethanol in the NpT ensemble and for the rigid TIP4P water model in the Gibbs ensemble gain slightly in efficiency with the k-d tree, whereas simulations for TIP4P water in the NpT ensemble do not benefit from the use of the k-d tree. The speed-up can be attributed to the reduction in the number of distance calculations in the range search from scaling as [Formula: see text] to [Formula: see text]. In addition, these tests suggest that the efficiency gain from the use of the k-d tree data structure depends on the flexibility of the molecular model (requiring configurational-bias MC moves to sample changes in conformation), on the ensemble (with open ensembles requiring special MC moves to aid particle transfers), and on the number of interaction sites per molecule (with compact multisite models not seeing an efficiency gain). Overall, the use of the k-d tree data structure can substantially enhance MC simulation efficiency for a variety of systems, and it will enable simulations for larger system sizes in the future.

  6. Convergence acceleration for partitioned simulations of the fluid-structure interaction in arteries

    NASA Astrophysics Data System (ADS)

    Radtke, Lars; Larena-Avellaneda, Axel; Debus, Eike Sebastian; Düster, Alexander

    2016-06-01

    We present a partitioned approach to fluid-structure interaction problems arising in analyses of blood flow in arteries. Several strategies to accelerate the convergence of the fixed-point iteration resulting from the coupling of the fluid and the structural sub-problem are investigated. The Aitken relaxation and variants of the interface quasi-Newton -least-squares method are applied to different test cases. A hybrid variant of two well-known variants of the interface quasi-Newton-least-squares method is found to perform best. The test cases cover the typical boundary value problem faced when simulating the fluid-structure interaction in arteries, including a strong added mass effect and a wet surface which accounts for a large part of the overall surface of each sub-problem. A rubber-like Neo Hookean material model and a soft-tissue-like Holzapfel-Gasser-Ogden material model are used to describe the artery wall and are compared in terms of stability and computational expenses. To avoid any kind of locking, high-order finite elements are used to discretize the structural sub-problem. The finite volume method is employed to discretize the fluid sub-problem. We investigate the influence of mass-proportional damping and the material model chosen for the artery on the performance and stability of the acceleration strategies as well as on the simulation results. To show the applicability of the partitioned approach to clinical relevant studies, the hemodynamics in a pathologically deformed artery are investigated, taking the findings of the test case simulations into account.

  7. High power breakdown testing of a photonic band-gap accelerator structure with elliptical rods

    NASA Astrophysics Data System (ADS)

    Munroe, Brian J.; Cook, Alan M.; Shapiro, Michael A.; Temkin, Richard J.; Dolgashev, Valery A.; Laurent, Lisa L.; Lewandowski, James R.; Yeremian, A. Dian; Tantawi, Sami G.; Marsh, Roark A.

    2013-01-01

    An improved single-cell photonic band-gap (PBG) structure with an inner row of elliptical rods (PBG-E) was tested with high power at a 60 Hz repetition rate at X-band (11.424 GHz), achieving a gradient of 128MV/m at a breakdown probability of 3.6×10-3 per pulse per meter at a pulse length of 150 ns. The tested standing-wave structure was a single high-gradient cell with an inner row of elliptical rods and an outer row of round rods; the elliptical rods reduce the peak surface magnetic field by 20% and reduce the temperature rise of the rods during the pulse by several tens of degrees, while maintaining good damping and suppression of high order modes. When compared with a single-cell standing-wave undamped disk-loaded waveguide structure with the same iris geometry under test at the same conditions, the PBG-E structure yielded the same breakdown rate within measurement error. The PBG-E structure showed a greatly reduced breakdown rate compared with earlier tests of a PBG structure with round rods, presumably due to the reduced magnetic fields at the elliptical rods vs the fields at the round rods, as well as use of an improved testing methodology. A post-testing autopsy of the PBG-E structure showed some damage on the surfaces exposed to the highest surface magnetic and electric fields. Despite these changes in surface appearance, no significant change in the breakdown rate was observed in testing. These results demonstrate that PBG structures, when designed with reduced surface magnetic fields and operated to avoid extremely high pulsed heating, can operate at breakdown probabilities comparable to undamped disk-loaded waveguide structures and are thus viable for high-gradient accelerator applications.

  8. High Gradient Performance of NLC/GLC X-band Accelerating Structures

    SciTech Connect

    Doebert, S.; Adolphsen, C.; Bowden, G.; Burke, D.; Chan, J.; Dolgashev, V.; Frisch, J.; Jobe, K.; Jones, R.; Lewandowski, J.; Kirby, R.; Li, Z.; McCormick, D.; Miller, R.; Nantista, C.; Nelson, J.; Pearson, C.; Ross, M.; Schultz, D.; Smith, T.; Tantawi, S.; /SLAC /Fermilab /KEK, Tsukuba

    2005-05-17

    During the past five years, there has been a concerted program at SLAC and KEK to develop accelerator structures that meet the high gradient (65 MV/m) performance requirements for the Next Linear Collider (NLC) and Global Linear Collider (GLC) initiatives. The design that resulted is a 60-cm-long, traveling-wave structure with low group velocity and 150 degree per cell phase advance. It has an average iris size that produces an acceptable short-range wakefield, and dipole mode damping and detuning that adequately suppresses the long-range wakefield. More than eight such structures have operated at a 60 Hz repetition rate over 1000 hours at 65 MV/m with 400 ns long pulses, and have reached breakdown rate levels below the limit for the linear collider. Moreover, the structures are robust in that the rates continue to decrease over time, and if the structures are briefly exposed to air, the rates recover to their low levels within a few days. This paper presents a summary of the results from this program, which effectively ended last August with the selection of ''cold'' technology for an International Linear Collider (ILC).

  9. Beam Position Monitoring using the HOM-Signals from a Damped and Detuned Accelerating Structure

    SciTech Connect

    Dobert, S; Adolphsen, C.; Jones, R.; Lewandowski, J.; Li, Z.; Pivi, M.; Wang, J.; Higo, T.; /KEK, Tsukuba

    2005-05-17

    The Next and Global Linear Collider (NLC/GLC) designs require precision alignment of the beam in the accelerator structures to reduce short range wakefields. The moderately damped and detuned structures themselves provide suitable higher order mode (HOM) signals to measure this alignment. The modes in the lowest dipole band, whose frequencies range from 14-16 GHz, provide the strongest signals. To determine the position resolution they provide, an NLC/GLC prototype structure that was installed in the ASSET facility of the SLAC Linac was instrumented to downmix and digitize these signals. The beam position within the structure was determined by simultaneously measuring the signals at three frequencies (14.3, 15, 15.7 GHz) corresponding to modes localized at the beginning, the middle and the end of the 60 cm long structure. A resolution of 1 micron was achieved even with 28 dB signal attenuation, which is better than the 5 micron resolution required for the NLC/GLC.

  10. Acceleration Data Reveal Highly Individually Structured Energetic Landscapes in Free-Ranging Fishers (Pekania pennanti)

    PubMed Central

    Scharf, Anne K.; LaPoint, Scott; Wikelski, Martin; Safi, Kamran

    2016-01-01

    Investigating animal energy expenditure across space and time may provide more detailed insight into how animals interact with their environment. This insight should improve our understanding of how changes in the environment affect animal energy budgets and is particularly relevant for animals living near or within human altered environments where habitat change can occur rapidly. We modeled fisher (Pekania pennanti) energy expenditure within their home ranges and investigated the potential environmental and spatial drivers of the predicted spatial patterns. As a proxy for energy expenditure we used overall dynamic body acceleration (ODBA) that we quantified from tri-axial accelerometer data during the active phases of 12 individuals. We used a generalized additive model (GAM) to investigate the spatial distribution of ODBA by associating the acceleration data to the animals' GPS-recorded locations. We related the spatial patterns of ODBA to the utilization distributions and habitat suitability estimates across individuals. The ODBA of fishers appears highly structured in space and was related to individual utilization distribution and habitat suitability estimates. However, we were not able to predict ODBA using the environmental data we selected. Our results suggest an unexpected complexity in the space use of animals that was only captured partially by re-location data-based concepts of home range and habitat suitability. We suggest future studies recognize the limits of ODBA that arise from the fact that acceleration is often collected at much finer spatio-temporal scales than the environmental data and that ODBA lacks a behavioral correspondence. Overcoming these limits would improve the interpretation of energy expenditure in relation to the environment. PMID:26840399

  11. Research of L-band disk-loaded waveguides travelling wave accelerating structures for a high power Linac

    NASA Astrophysics Data System (ADS)

    Zhang, Y. M.; Pei, Y. J.; Sheng, L. S.; Song, Y. F.

    2017-07-01

    L-band Electron Accelerator has been widely utilized for industrial irradiation. In this paper, we designed a constant-impedance, disk-loaded structure which operates on 2π/3 mode. CST and SUPERFISH code were used for the design of bunching and accelerating cavities respectively. The geometrical parameters of the cavities were studied, and optimized RF parameters were obtained. We calculated the beam dynamics which presented that the electrons can be accelerated to 50 MeV. The model cavities have been fabricated and tested. Some valuable experimental results were obtained, which can provide a beneficial datum for the design and manufacture of L-band travelling-wave accelerating structures of 50 MeV LINAC.

  12. A Mode-Accelerated XXr (MAX) method for complex structures with large blends

    NASA Astrophysics Data System (ADS)

    Gan, Yiqian; Mayer, John L.; D'Souza, Kiran X.; Epureanu, Bogdan I.

    2017-09-01

    Various reduced order models have been proposed for characterizing cyclic symmetric structures with complex geometry and varying material properties that are subject to complex boundary or loading conditions. Small variations can be represented as small mass or stiffness mistuning. Techniques developed to handle such variations rely on the fact that the modes of the system can be accurately approximated using a linear combination of modes of the healthy/nominal system. Such approximations are valid in regions of high modal density, but they break down when variations are large or geometric changes are present. To address this challenge, a novel method is presented to predict the vibration response of cyclic symmetric structures with large geometric changes due to damage in the form of missing material (blends). The central idea of the new approach is an extension of the XXr method for cracked structures. The XXr method was developed for modeling small mistuning and large cracks. That method is extended in this work to handle large blends. In addition, a specialized component mode synthesis is combined with the extended XXr method to maintain accuracy. Also, unique to the proposed novel method is a technique to accelerate the convergence of the order reduction, and thus obtain very low order models. These low order models provide excellent computational speed and effectiveness while maintaining accuracy. Therefore, the method can be applied to highly refined, realistic models of industrial size. To demonstrate the proposed mode-accelerated XXr method, the effects of large blends on the response of a bladed disk are investigated.

  13. SOFIA-EXES: Probing the Thermal Structure of M Supergiant Wind Acceleration Zones

    NASA Astrophysics Data System (ADS)

    Harper, Graham M.; O'Gorman, Eamon; Guinan, Edward F.; EXES Instrument Team, EXES Science Team

    2016-01-01

    There is no standard model for mass loss from cool evolved stars, particularly for non-pulsating giants and supergiants. For the early-M supergiants, radiation pressure, convective ejections, magnetic fields, and Alfven waves have all been put forward as potential mass loss mechanisms. A potential discriminator between these ideas is the thermal structure resulting from the heating-cooling balance in the acceleration zone - the most important region to study mass loss physics.We present mid-IR [Fe II] emission line profiles of Betelgeuse and Antares obtained with NASA-DLR SOFIA-EXES and NASA IRTF-TEXES that were obtained as part of a GO program (Harper: Cycle 2-0004) and EXES instrument commissioning observations. The intra-term transitions sample a range of excitation conditions, Texc=540K, 3,400K, and 11,700K, i.e., from the warm chromospheric plasma, that also emits in the cm-radio and ultraviolet, to the cold inner circumstellar envelope. The spectrally-resolved profiles, when combined with VLA cm-radio observations, provide new constraints on the temperature and flow velocity in the outflow accelerating region. The semi-empirical energy balance can be used to test theoretical predictions of wind heating.

  14. Accelerators for Fusion Materials Testing

    NASA Astrophysics Data System (ADS)

    Knaster, Juan; Okumura, Yoshikazu

    with the International Fusion Materials Irradiation Facility (IFMIF) under discussion at the time. Worldwide technological efforts are maturing soundly and the time for a fusion-relevant neutron source has arrived according to world fusion roadmaps; if decisions are taken we could count the next decade with a powerful source of 14 MeV neutrons thanks to the expected significant results of the Engineering Validation and Engineering Design Activity (EVEDA) phase of the IFMIF project. The accelerator know-how has matured in all possible aspects since the times of FMIT conception in the 1970s; today, operating 125 mA deuteron beam at 40 MeV in CW with high availabilities seems feasible thanks to the understanding of the beam halo physics and the three main technological breakthroughs in accelerator technology: (1) the ECR ion source for light ions developed at Chalk River Laboratories in the early 1990s, (2) the RFQ operation of H+ in CW with 100 mA demonstrated by LEDA in LANL in the late 1990s, and (3) the growing maturity of superconducting resonators for light hadrons and low β beams achieved in recent years.

  15. Accelerators for Fusion Materials Testing

    NASA Astrophysics Data System (ADS)

    Knaster, Juan; Okumura, Yoshikazu

    with the International Fusion Materials Irradiation Facility (IFMIF) under discussion at the time. Worldwide technological efforts are maturing soundly and the time for a fusion-relevant neutron source has arrived according to world fusion roadmaps; if decisions are taken we could count the next decade with a powerful source of 14 MeV neutrons thanks to the expected significant results of the Engineering Validation and Engineering Design Activity (EVEDA) phase of the IFMIF project. The accelerator know-how has matured in all possible aspects since the times of FMIT conception in the 1970s; today, operating 125 mA deuteron beam at 40 MeV in CW with high availabilities seems feasible thanks to the understanding of the beam halo physics and the three main technological breakthroughs in accelerator technology: (1) the ECR ion source for light ions developed at Chalk River Laboratories in the early 1990s, (2) the RFQ operation of H+ in CW with 100 mA demonstrated by LEDA in LANL in the late 1990s, and (3) the growing maturity of superconducting resonators for light hadrons and low β beams achieved in recent years.

  16. Development of a Laser-Powered Dielectric Structure-Based Accelerator as a Stand-Alone Particle Source

    NASA Astrophysics Data System (ADS)

    Yoder, R. B.; Travish, G.; Arab, E. R.; Fong, D.; Hoyer, Z.; Lacroix, U. H.; Vartanian, N.; Rosenzweig, J. B.

    2010-11-01

    An experimental program to develop and build a dielectric-based slab-symmetric structure (the micro-accelerator platform, or MAP) for generating and accelerating low-energy electrons is underway at UCLA and Manhattanville College. This optical acceleration structure is effectively a resonant cavity powered by a side-coupled laser, and has applications as a radiation source for medicine or industry. We present recent experimental and computational results on the accelerator, and progress toward its incorporation into a self-contained particle source. Such a particle source would incorporate a micron-scale electron emitter and a non-relativistic capture region to enable self-injection into the synchronous field within the accelerator. A prototype of the accelerator itself has been constructed from candidate dielectric materials using micromanufacturing techniques; the current status of the testing program is described. A novel electron emitter incorporating pyroelectric crystals with field-enhancing tips has been demonstrated to produce steady currents; the results are dependent on tip geometry, and appear suitable for injection into a microstructure. Extension of the MAP concept to non-relativistic velocities, as in the stand-alone source, requires a tapered structure that gives rise to numerous complications including beam defocusing and manufacturing challenges; approaches for addressing these complications are mentioned.

  17. Selection of flowing liquid lead target structural materials for accelerator driven transmutation applications

    NASA Astrophysics Data System (ADS)

    Park, John J.; Buksa, John J.

    1995-09-01

    The beam entry window and container for a liquid lead spallation target will be exposed to high fluxes of protons and neutrons that are both higher in magnitude and energy than have been experienced in proton accelerators and fission reactors, as well as in a corrosive environment. The structural material of the target should have a good compatibility with liquid lead, a sufficient mechanical strength at elevated temperatures, a good performance under an intense irradiation environment, and a low neutron absorption cross section; these factors have been used to rank the applicability of a wide range of materials for structural containment. Nb-1Zr has been selected for use as the structural container for the LANL ABC/ATW molten lead target. Corrosion and mass transfer behavior for various candidate structural materials in liquid lead are reviewed, together with the beneficial effects of inhibitors and various coatings to protect substrate against liquid lead corrosion. Mechanical properties of some candidate materials at elevated temperatures and the property changes resulting from 800 MeV proton irradiation are also reviewed.

  18. Selection of flowing liquid lead target structural materials for accelerator driven transmutation applications

    SciTech Connect

    Park, J.J.; Buksa, J.J.

    1994-08-01

    The beam entry window and container for a liquid lead spallation target will be exposed to high fluxes of protons and neutrons that are both higher in magnitude and energy than have been experienced in proton accelerators and fission reactors, as well as in a corrosive environment. The structural material of the target should have a good compatibility with liquid lead, a sufficient mechanical strength at elevated temperatures, a good performance under an intense irradiation environment, and a low neutron absorption cross section; these factors have been used to rank the applicability of a wide range of materials for structural containment Nb-1Zr has been selected for use as the structural container for the LANL ABC/ATW molten lead target. Corrosion and mass transfer behavior for various candidate structural materials in liquid lead are reviewed, together with the beneficial effects of inhibitors and various coatings to protect substrate against liquid lead corrosion. Mechanical properties of some candidate materials at elevated temperatures and the property changes resulting from 800 MeV proton irradiation are also reviewed.

  19. Muscle mass, structural and functional investigations of senescence-accelerated mouse P8 (SAMP8)

    PubMed Central

    Guo, An Yun; Leung, Kwok Sui; Siu, Parco Ming Fai; Qin, Jiang Hui; Chow, Simon Kwoon Ho; Qin, Ling; Li, Chi Yu; Cheung, Wing Hoi

    2015-01-01

    Sarcopenia is an age-related systemic syndrome with progressive deterioration in skeletal muscle functions and loss in mass. Although the senescence-accelerated mouse P8 (SAMP8) was reported valid for muscular ageing research, there was no report on the details such as sarcopenia onset time. Therefore, this study was to investigate the change of muscle mass, structure and functions during the development of sarcopenia. Besides the average life span, muscle mass, structural and functional measurements were also studied. Male SAMP8 animals were examined at month 6, 7, 8, 9, and 10, in which the right gastrocnemius was isolated and tested for ex vivo contractile properties and fatigability while the contralateral one was harvested for muscle fiber cross-sectional area (FCSA) and typing assessments. Results showed that the peak of muscle mass appeared at month 7 and the onset of contractility decline was observed from month 8. Compared with month 8, most of the functional parameters at month 10 decreased significantly. Structurally, muscle fiber type IIA made up the largest proportion of the gastrocnemius, and the fiber size was found to peak at month 8. Based on the altered muscle mass, structural and functional outcomes, it was concluded that the onset of sarcopenia in SAMP8 animals was at month 8. SAMP8 animals at month 8 should be at pre-sarcopenia stage while month 10 at sarcopenia stage. It is confirmed that SAMP8 mouse can be used in sarcopenia research with established time line in this study. PMID:26193895

  20. High power experimental studies of hybrid photonic band gap accelerator structures

    DOE PAGES

    Zhang, JieXi; Munroe, Brian J.; Xu, Haoran; ...

    2016-08-31

    This paper reports the first high power tests of hybrid photonic band gap (PBG) accelerator structures. Three hybrid PBG (HPBG) structures were designed, built and tested at 17.14 GHz. Each structure had a triangular lattice array with 60 inner sapphire rods and 24 outer copper rods sandwiched between copper disks. The dielectric PBG band gap map allows the unique feature of overmoded operation in a TM02 mode, with suppression of both lower order modes, such as the TM11 mode, as well as higher order modes. The use of sapphire rods, which have negligible dielectric loss, required inclusion of the dielectricmore » birefringence in the design. The three structures were designed to sequentially reduce the peak surface electric field. Simulations showed relatively high surface fields at the triple point as well as in any gaps between components in the clamped assembly. The third structure used sapphire rods with small pin extensions at each end and obtained the highest gradient of 19 MV/m, corresponding to a surface electric field of 78 MV/m, with a breakdown probability of 5×10–1 per pulse per meter for a 100-ns input power pulse. Operation at a gradient above 20 MV/m led to runaway breakdowns with extensive light emission and eventual damage. For all three structures, multipactor light emission was observed at gradients well below the breakdown threshold. As a result, this research indicated that multipactor triggered at the triple point limited the operational gradient of the hybrid structure.« less

  1. Influence of solidification accelerators on structure formation of anhydrite-containing binders

    NASA Astrophysics Data System (ADS)

    Anikanova, L.; Volkova, O.; Kudyakov, A.; Sarkisov, Y.; Tolstov, D.

    2016-01-01

    The article presents results of scientific analysis of chemical additives influence on acid fluoride binder. It was found that the influence of sulfate nature additives on the process of hydration and solidification of the binder is similar to influence of additives on indissoluble anhydrite. Additives with SO42- anion NO- are more efficient. The mentioned additives according to accelerating effect belong to the following succession: K2SO4 > Na2SO4 > FeSO4 > MgSO4. Facilitation of the process of hydration and solidification of the binder, increase in density and durability of the binder (32 MPa) is to the greatest extent achieved with the introduction of 2% sodium sulfate additive of the binder's mass into the composition of the binder along with the ultrasonic treatment of water solution. Directed crystal formation process with healing of porous structure by new growths presented as calcium sulfate dehydrate and hydroglauberite provides positive effect.

  2. Determination of molecular-ion structures through the use of accelerated beams

    SciTech Connect

    Gemmell, D.S.

    1987-01-01

    In this talk we report on recent research on molecular-ion structures using fast molecular-ion beams provided by Argonne's 5-MV Dynamitron accelerator. The method has become known as the ''Coulomb-explosion'' technique. When molecular-ion projectiles travelling at velocities of a few percent of the velocity of light strike a foil, the electrons that bind the molecular projectiles are almost always totally stripped off within the first few Angstroms of penetration into the solid target. This leaves a cluster of bare (or nearly bare) nuclei which separate rapidly as a result of their mutual Coulomb repulsion. This violent dissociation process in which the initial electrostatic potential energy is converted into kinetic energy of relative motion in the center-of-mass, has been termed a ''Coulomb explosion.'' 4 refs., 2 figs.

  3. Relativistic magnetosonic shock waves in synchrotron sources - Shock structure and nonthermal acceleration of positrons

    NASA Technical Reports Server (NTRS)

    Hoshino, Masahiro; Arons, Jonathan; Gallant, Yves A.; Langdon, A. B.

    1992-01-01

    The theoretical properties of relativistic, transverse, magnetosonic collisionless shock waves in electron-positron-heavy ion plasmas of relevance to astrophysical sources of synchrotron radiation are investigated. Both 1D electromagnetic particle-in-cell simulations and quasi-linear theory are used to examine the spatial and kinetic structure of these nonlinear flows. A new process of shock acceleration of nonthermal positrons, in which the gyrating reflected heavy ions dissipate their energy in the form of collectively emitted, left-handed magnetosonic waves which are resonantly absorbed by the positrons immediately behind the ion reflection region, is described. Applications of the results to the termination shocks of pulsar winds and to the termination shocks of jets emanating from the AGN are outlined.

  4. Multiple quasi-monoenergetic electron beams from laser-wakefield acceleration with spatially structured laser pulse

    SciTech Connect

    Ma, Y.; Li, M. H.; Li, Y. F.; Wang, J. G.; Tao, M. Z.; Han, Y. J.; Zhao, J. R.; Huang, K.; Yan, W. C.; Ma, J. L.; Li, Y. T.; Chen, L. M.; Li, D. Z.; Chen, Z. Y.; Sheng, Z. M.; Zhang, J.

    2015-08-15

    By adjusting the focus geometry of a spatially structured laser pulse, single, double, and treble quasi-monoenergetic electron beams were generated, respectively, in laser-wakefield acceleration. Single electron beam was produced as focusing the laser pulse to a single spot. While focusing the laser pulse to two spots that are approximately equal in energy and size and intense enough to form their own filaments, two electron beams were produced. Moreover, with a proper distance between those two focal spots, three electron beams emerged with a certain probability owing to the superposition of the diffractions of those two spots. The energy spectra of the multiple electron beams are quasi-monoenergetic, which are different from that of the large energy spread beams produced due to the longitudinal multiple-injection in the single bubble.

  5. Determination of molecular-ion structures through the use of accelerated beams

    NASA Astrophysics Data System (ADS)

    Gemmell, D. S.

    In this talk we report on recent research on molecular-ion structures using fast molecular-ion beams provided by Argonne's 5-MV Dynamitron accelerator. The method has become known as the Coulomb-explosion technique. When molecular-ion projectiles travelling at velocities of a few percent of the velocity of light strike a foil, the electrons that bind the molecular projectiles are almost always totally stripped off within the first few Angstroms of penetration into the solid target. This leaves a cluster of bare (or nearly bare) nuclei which separate rapidly as a result of their mutual Coulomb repulsion. This violent dissociation process in which the initial electrostatic potential energy is converted into kinetic energy of relative motion in the center-of-mass, was termed a Coulomb explosion.

  6. Observation of multipactor in an alumina-based dielectric-loaded accelerating structure.

    PubMed

    Power, J G; Gai, W; Gold, S H; Kinkead, A K; Konecny, R; Jing, C; Liu, W; Yusof, Z

    2004-04-23

    We report a new regime of single-surface multipactor that was observed during high-power testing of an 11.424-GHz alumina-based dielectric-loaded accelerating structure. Previous experimental observations of single-surface multipactor on a dielectric occurred in cases for which the rf electric field was tangential and the rf power flow was normal to the dielectric surface (such as on rf windows) and found that the fraction of power absorbed at saturation is approximately 1%, independent of the incident power. In this new regime, in which strong normal and tangential rf electric fields are present and the power flow is parallel to the surface, the fraction of power absorbed at saturation is an increasing function of the incident power, and more than half of the incident power can be absorbed. A simple model is presented to explain the experimental results.

  7. Near-relativistic electron acceleration by Landau trapping in time domain structures

    NASA Astrophysics Data System (ADS)

    Mozer, F. S.; Artemyev, A.; Agapitov, O. V.; Mourenas, D.; Vasko, I.

    2016-01-01

    Data from the Van Allen Probes have provided the first extensive evidence of nonlinear (as opposed to quasi-linear) wave-particle interactions in space with the associated rapid (less than a bounce period) electron acceleration to hundreds of keV by Landau resonance in the parallel electric field of time domain structures (TDSs) traveling at high speeds (~20,000 km/s). This observational evidence is supported by simulations and discussion of the source and spatial extent of the fast TDS. This result indicates the possibility that the electrostatic fields in TDS may generate the electron seed population for cyclotron resonance interaction with chorus waves to make higher-energy electrons.

  8. Structure Loaded Vacuum Laser-Driven Particle Acceleration Experiments at SLAC

    SciTech Connect

    Plettner, T.; Byer, R.L.; Colby, E.R.; Cowan, B.M.; Ischebeck, R.; McGuinness, C.; Lincoln, M.R.; Sears, C.M.; Siemann, R.H.; Spencer, J.E.; /SLAC /Stanford U., Phys. Dept.

    2007-04-09

    We present an overview of the future laser-driven particle acceleration experiments. These will be carried out at the E163 facility at SLAC. Our objectives include a reconfirmation of the proof-of-principle experiment, a staged buncher laser-accelerator experiment, and longer-term future experiments that employ dielectric laser-accelerator microstructures.

  9. Track Structure and the Biological Effectiveness of Accelerated Particles for the Induction of Chromosome Damage

    NASA Technical Reports Server (NTRS)

    George, K.; Hada, M.; Chappell, L.; Cucinotta, F. A.

    2011-01-01

    Track structure models predict that at a fixed value of LET, particles with lower charge number, Z will have a higher biological effectiveness compared to particles with a higher Z. In this report we investigated how track structure effects induction of chromosomal aberration in human cells. Human lymphocytes were irradiated in vitro with various energies of accelerated iron, silicon, neon, or titanium ions and chromosome damage was assessed in using three color FISH chromosome painting in chemically induced PCC samples collected a first cell division post irradiation. The LET values for these ions ranged from 30 to195 keV/micron. Of the particles studied, Neon ions have the highest biological effectiveness for induction of total chromosome damage, which is consistent with track structure model predictions. For complex-type exchanges 64 MeV/ u Neon and 450 MeV/u Iron were equally effective and induced the most complex damage. In addition we present data on chromosomes exchanges induced by six different energies of protons (5 MeV/u to 2.5 GeV/u). The linear dose response term was similar for all energies of protons suggesting that the effect of the higher LET at low proton energies is balanced by the production of nuclear secondaries from the high energy protons.

  10. Accelerating Convolutional Sparse Coding for Curvilinear Structures Segmentation by Refining SCIRD-TS Filter Banks.

    PubMed

    Annunziata, Roberto; Trucco, Emanuele

    2016-11-01

    Deep learning has shown great potential for curvilinear structure (e.g., retinal blood vessels and neurites) segmentation as demonstrated by a recent auto-context regression architecture based on filter banks learned by convolutional sparse coding. However, learning such filter banks is very time-consuming, thus limiting the amount of filters employed and the adaptation to other data sets (i.e., slow re-training). We address this limitation by proposing a novel acceleration strategy to speed-up convolutional sparse coding filter learning for curvilinear structure segmentation. Our approach is based on a novel initialisation strategy (warm start), and therefore it is different from recent methods improving the optimisation itself. Our warm-start strategy is based on carefully designed hand-crafted filters (SCIRD-TS), modelling appearance properties of curvilinear structures which are then refined by convolutional sparse coding. Experiments on four diverse data sets, including retinal blood vessels and neurites, suggest that the proposed method reduces significantly the time taken to learn convolutional filter banks (i.e., up to -82%) compared to conventional initialisation strategies. Remarkably, this speed-up does not worsen performance; in fact, filters learned with the proposed strategy often achieve a much lower reconstruction error and match or exceed the segmentation performance of random and DCT-based initialisation, when used as input to a random forest classifier.

  11. Beam-based measurements of long-range transverse wakefields in the Compact Linear Collider main-linac accelerating structure

    DOE PAGES

    Zha, Hao; Latina, Andrea; Grudiev, Alexej; ...

    2016-01-20

    The baseline design of CLIC (Compact Linear Collider) uses X-band accelerating structures for its main linacs. In order to maintain beam stability in multibunch operation, long-range transverse wakefields must be suppressed by 2 orders of magnitude between successive bunches, which are separated in time by 0.5 ns. Such strong wakefield suppression is achieved by equipping every accelerating structure cell with four damping waveguides terminated with individual rf loads. A beam-based experiment to directly measure the effectiveness of this long-range transverse wakefield and benchmark simulations was made in the FACET test facility at SLAC using a prototype CLIC accelerating structure. Furthermore,more » the experiment showed good agreement with the simulations and a strong suppression of the wakefields with an unprecedented minimum resolution of 0.1 V/(pC mm m).« less

  12. Structure of a strong supernova shock wave and rapid electron acceleration confined in its transition region

    SciTech Connect

    Shimada, N.; Hoshino, M.; Amano, T.

    2010-03-15

    A new rapid energization process within a supernova shock transition region (STR) is reported by utilizing numerical simulation. Although the scale of a STR as a main dissipation region is only several hundreds of thousands of kilometers, several interesting structures are found relating to the generation of a root of the energetic particles. The nonlinear evolution of plasma instabilities leads to a dynamical change in the ion phase space distribution, which associates with change in the field properties. As a result, different types of large-amplitude field structures appear. One is the leading wave packet, and another is a series of magnetic solitary humps. Each field structure has a microscopic scale (that is, the ion inertia length). Through the multiple nonlinear scattering between these large-amplitude field structures, electrons are accelerated directly. Within a STR, quick thermalization realizes energy equipartition between the ion and electron; hot electrons play an important role in keeping these large-amplitude field structures on the ion-acoustic mode. The hot electron shows non-Maxwellian distribution and could be the seed of further nonthermal population. The 'shock system', where fresh incoming and reflected ions are supplied constantly, play an essential role in our result. With a perpendicular shock geometry, the maximum energy of the electron is estimated by equating a width of the STR to a length of the Larmor radius of the energetic electron. Under some realistic condition of M{sub A}=170 and omega{sub pe}/OMEGA{sub ce}=120, maximum energy is estimated to be approx10 MeV at an instant only within the STR.

  13. VLA Observations of ζ Aurigae: Confirmation of the Slow Acceleration Wind Density Structure

    NASA Astrophysics Data System (ADS)

    Harper, Graham M.; Brown, Alexander; Bennett, Philip D.; Baade, Robert; Walder, Rolf; Hummel, Christian A.

    2005-02-01

    Studies of the winds from single K and early M evolved stars indicate that these flows typically reach a significant fraction of their terminal velocity within the first couple of stellar radii. The most detailed spatially resolved information of the extended atmospheres of these spectral types comes from the ζ Aur eclipsing binaries. However, the wind acceleration inferred for the evolved primaries in these systems appears significantly slower than for stars of similar spectral type. Since there are no successful theories for mass loss from K and early M evolved stars, it is important to place strong empirical constraints on potential models and determine whether this difference in acceleration is real or an artifact of the analyses. We have undertaken a radio continuum monitoring study of ζ Aurigae (K4 Ib + B5 V) using the Very Large Array to test the wind density model of Baade et al. that is based on Hubble Space Telescope (HST) Goddard High Resolution Spectrograph ultraviolet spectra. ζ Aur was monitored at centimeter wavelengths over a complete orbital cycle, and flux variations during the orbit are found to be of similar magnitude to variations at similar orbital phases in the adjacent orbit. During eclipse, the flux does not decrease, showing that the radio emission originates from a volume substantially larger than R3K~(150Rsolar)3 surrounding the B star. Using the one-dimensional density model of the K4 Ib primary's wind derived from HST spectral line profile modeling and electron temperature estimates from previous optical and new HST studies, we find that the predicted radio fluxes are consistent with those observed. Three-dimensional hydrodynamic simulations indicate that the accretion flow perturbations near the B star do not contribute significantly to the total radio flux from the system, consistent with the radio eclipse observations. Our radio observations confirm the slow wind acceleration for the evolved K4 Ib component. ζ Aur's velocity

  14. Zinc promotes clot stability by accelerating clot formation and modifying fibrin structure.

    PubMed

    Henderson, Sara J; Xia, Jing; Wu, Huayin; Stafford, Alan R; Leslie, Beverly A; Fredenburgh, James C; Weitz, David A; Weitz, Jeffrey I

    2016-03-01

    Zinc released from activated platelets binds fibrin(ogen) and attenuates fibrinolysis. Although zinc also affects clot formation, the mechanism and consequences are poorly understood. To address these gaps, the effect of zinc on clot formation and structure was examined in the absence or presence of factor (F) XIII. Zinc accelerated a) plasma clotting by 1.4-fold, b) fibrinogen clotting by 3.5- and 2.3-fold in the absence or presence of FXIII, respectively, c) fragment X clotting by 1.3-fold, and d) polymerisation of fibrin monomers generated with thrombin or batroxobin by 2.5- and 1.8-fold, respectively. Whereas absorbance increased up to 3.3-fold when fibrinogen was clotted in the presence of zinc, absorbance of fragment X clots was unaffected by zinc, consistent with reports that zinc binds to the αC-domain of fibrin(ogen). Scanning electron microscopic analysis revealed a two-fold increase in fibre diameter in the presence of zinc and in permeability studies, zinc increased clot porosity by 30-fold with or without FXIII. Whereas FXIII increased clot stiffness from 128 ± 19 Pa to 415 ± 27 Pa in rheological analyses, zinc reduced clot stiffness by 10- and 8.5-fold in the absence and presence of FXIII, respectively. Clots formed in the presence of zinc were more stable and resisted rupture with or without FXIII. Therefore, zinc accelerates clotting and reduces fibrin clot stiffness in a FXIII-independent manner, suggesting that zinc may work in concert with FXIII to modulate clot strength and stability.

  15. A Coupled Multiphysics Approach for Simulating Induced Seismicity, Ground Acceleration and Structural Damage

    NASA Astrophysics Data System (ADS)

    Podgorney, Robert; Coleman, Justin; Wilkins, Amdrew; Huang, Hai; Veeraraghavan, Swetha; Xia, Yidong; Permann, Cody

    2017-04-01

    Numerical modeling has played an important role in understanding the behavior of coupled subsurface thermal-hydro-mechanical (THM) processes associated with a number of energy and environmental applications since as early as the 1970s. While the ability to rigorously describe all key tightly coupled controlling physics still remains a challenge, there have been significant advances in recent decades. These advances are related primarily to the exponential growth of computational power, the development of more accurate equations of state, improvements in the ability to represent heterogeneity and reservoir geometry, and more robust nonlinear solution schemes. The work described in this paper documents the development and linkage of several fully-coupled and fully-implicit modeling tools. These tools simulate: (1) the dynamics of fluid flow, heat transport, and quasi-static rock mechanics; (2) seismic wave propagation from the sources of energy release through heterogeneous material; and (3) the soil-structural damage resulting from ground acceleration. These tools are developed in Idaho National Laboratory's parallel Multiphysics Object Oriented Simulation Environment, and are integrated together using a global implicit approach. The governing equations are presented, the numerical approach for simultaneously solving and coupling the three coupling physics tools is discussed, and the data input and output methodology is outlined. An example is presented to demonstrate the capabilities of the coupled multiphysics approach. The example involves simulating a system conceptually similar to the geothermal development in Basel Switzerland, and the resultant induced seismicity, ground motion and structural damage is predicted.

  16. Numerical studies and measurements on the side-coupled drift tube linac (SCDTL) accelerating structure

    NASA Astrophysics Data System (ADS)

    Picardi, L.; Ronsivalle, C.; Spataro, B.

    2000-09-01

    The 3 GHz linac section designed for the low energy (7-65 MeV) part of TOP (therapy oncological protons) linac (Picardi et al., 1997, 1996), operating at 3 GHz frequency and in π/2 mode, consists of eight modules of the structure SCDTL (side-coupled drift tube linac). The first module is designed to accelerate 7 MeV protons up to 13.4 MeV, and a prototype is presently under construction. Electromagnetic field calculations of the non-axisymmetric cavities carried out by using MAFIA 3D code (Weiland, 1986) gave the RF wall losses and the full mode spectrum. Two prototypes, an aluminium model of the first quintuplet and a copper model of the last triplet of the module, were built in order to check the complex 3D properties of the structure, and to refine the tuning procedure. This paper reports the results of the 3D numerical simulations about the RF properties of the first module and of some RF measurements on the prototypes. The beam dynamics study results in the SCDTL section are discussed as well.

  17. Analysis of a Symmetric Terahertz Dielectric-Lined Rectangular Structure for High Gradient Acceleration

    SciTech Connect

    Marshall, T. C.; Sotnikov, G. V.; Shchelkunov, S. V.; Hirshfield, J. L.

    2009-01-22

    We study, using computational methods based on analytic theory as well as a PIC code, the wakefields set up in a seven-zone symmetric rectangular THZ structure, and find that for overall transverse x/y dimensions 2.121 mmx0.6 mm, two 5-GeV drive bunches (3 nC, with x/y/z dimensions 0.3/0.3/0.12 mm{sup 3} as available at SLAC) will set up an axial wakefield {approx}350 MV/m in the witness channel, with a transformer ratio {approx}18-20. The symmetry of the structure ensures not only that small transverse forces are imposed on the witness bunch, but also that the two components of transverse force are equal and opposite at the bunch location so as to enable dynamical stabilization in an accelerator comprising many modules. Transverse forces on the drive bunch tails may allow bunches to move {approx}0.5-1 m without suffering excessive erosion.

  18. An accelerated stochastic vortex structure method for particle collision and agglomeration in homogeneous turbulence

    NASA Astrophysics Data System (ADS)

    Dizaji, Farzad F.; Marshall, Jeffrey S.

    2016-11-01

    Modeling the response of interacting particles, droplets, or bubbles to subgrid-scale fluctuations in turbulent flows is a long-standing challenge in multiphase flow simulations using the Reynolds-Averaged Navier-Stokes approach. The problem also arises for large-eddy simulation for sufficiently small values of the Kolmogorov-scale particle Stokes number. This paper expands on a recently proposed stochastic vortex structure (SVS) method for modeling of turbulence fluctuations for colliding or otherwise interacting particles. An accelerated version of the SVS method was developed using the fast multipole expansion and local Taylor expansion approach, which reduces computation speed by two orders of magnitude compared to the original SVS method. Detailed comparisons are presented showing close agreement of the energy spectrum and probability density functions of various fields between the SVS computational model, direct numerical simulation (DNS) results, and various theoretical and experimental results found in the literature. Results of the SVS method for particle collision rate and related measures of particle interaction exhibit excellent agreement with DNS predictions for homogeneous turbulent flows. The SVS method was also used with adhesive particles to simulate formation of particle agglomerates with different values of the particle Stokes and adhesion numbers, and various measures of the agglomerate structure are compared to the DNS results.

  19. Effect of gravitational acceleration, hypokinesia and hypodynamia on the structure of the intestinal vascular bed

    NASA Technical Reports Server (NTRS)

    Nikitin, M. V.

    1980-01-01

    A series of experiments comparing single and combined effects of hypokinesia and gravitational acceleration on morphology of intestinal blood vessels are discussed. Results indicate that hypokinesia has a whole body nonspecific effect reflected even in an organ whose activity shows little or no change due to hypokinesia. In early hypokinetic stages blood redistribution caused anorexia, intestinal atonia, and secretory disruption. Destructive changes from further exposure include aneurisms, varicoses, extravascular movement of blood elements, and vascular wall muscle fiber degeneration. The effect of acceleration is greatest in the ventrodorsal direction. Changes due to acceleration then hypokinesia are like those due to hypokinesia alone; changes due to acceleration before and after hypokinesia are like those due to acceleration. Adaptation raises acceleration tolerance but the effects do not survive four-week hypokinesia.

  20. Guided post-acceleration of laser-driven ions by a miniature modular structure

    NASA Astrophysics Data System (ADS)

    Kar, Satyabrata; Ahmed, Hamad; Prasad, Rajendra; Cerchez, Mirela; Brauckmann, Stephanie; Aurand, Bastian; Cantono, Giada; Hadjisolomou, Prokopis; Lewis, Ciaran L. S.; Macchi, Andrea; Nersisyan, Gagik; Robinson, Alexander P. L.; Schroer, Anna M.; Swantusch, Marco; Zepf, Matt; Willi, Oswald; Borghesi, Marco

    2016-04-01

    All-optical approaches to particle acceleration are currently attracting a significant research effort internationally. Although characterized by exceptional transverse and longitudinal emittance, laser-driven ion beams currently have limitations in terms of peak ion energy, bandwidth of the energy spectrum and beam divergence. Here we introduce the concept of a versatile, miniature linear accelerating module, which, by employing laser-excited electromagnetic pulses directed along a helical path surrounding the laser-accelerated ion beams, addresses these shortcomings simultaneously. In a proof-of-principle experiment on a university-scale system, we demonstrate post-acceleration of laser-driven protons from a flat foil at a rate of 0.5 GeV m-1, already beyond what can be sustained by conventional accelerator technologies, with dynamic beam collimation and energy selection. These results open up new opportunities for the development of extremely compact and cost-effective ion accelerators for both established and innovative applications.

  1. Guided post-acceleration of laser-driven ions by a miniature modular structure.

    PubMed

    Kar, Satyabrata; Ahmed, Hamad; Prasad, Rajendra; Cerchez, Mirela; Brauckmann, Stephanie; Aurand, Bastian; Cantono, Giada; Hadjisolomou, Prokopis; Lewis, Ciaran L S; Macchi, Andrea; Nersisyan, Gagik; Robinson, Alexander P L; Schroer, Anna M; Swantusch, Marco; Zepf, Matt; Willi, Oswald; Borghesi, Marco

    2016-04-18

    All-optical approaches to particle acceleration are currently attracting a significant research effort internationally. Although characterized by exceptional transverse and longitudinal emittance, laser-driven ion beams currently have limitations in terms of peak ion energy, bandwidth of the energy spectrum and beam divergence. Here we introduce the concept of a versatile, miniature linear accelerating module, which, by employing laser-excited electromagnetic pulses directed along a helical path surrounding the laser-accelerated ion beams, addresses these shortcomings simultaneously. In a proof-of-principle experiment on a university-scale system, we demonstrate post-acceleration of laser-driven protons from a flat foil at a rate of 0.5 GeV m(-1), already beyond what can be sustained by conventional accelerator technologies, with dynamic beam collimation and energy selection. These results open up new opportunities for the development of extremely compact and cost-effective ion accelerators for both established and innovative applications.

  2. ConnectViz: Accelerated approach for brain structural connectivity using Delaunay triangulation.

    PubMed

    Adeshina, A M; Hashim, R

    2015-02-06

    Stroke is a cardiovascular disease with high mortality and long-term disability in the world. Normal functioning of the brain is dependent on the adequate supply of oxygen and nutrients to the brain complex network through the blood vessels. Stroke, occasionally a hemorrhagic stroke, ischemia or other blood vessel dysfunctions can affect patients during a cerebrovascular incident. Structurally, the left and the right carotid arteries, and the right and the left vertebral arteries are responsible for supplying blood to the brain, scalp and the face. However, a number of impairment in the function of the frontal lobes may occur as a result of any decrease in the flow of the blood through one of the internal carotid arteries. Such impairment commonly results in numbness, weakness or paralysis. Recently, the concepts of brain's wiring representation, the connectome, was introduced. However, construction and visualization of such brain network requires tremendous computation. Consequently, previously proposed approaches have been identified with common problems of high memory consumption and slow execution. Furthermore, interactivity in the previously proposed frameworks for brain network is also an outstanding issue. This study proposes an accelerated approach for brain connectomic visualization based on graph theory paradigm using Compute Unified Device Architecture (CUDA), extending the previously proposed SurLens Visualization and Computer Aided Hepatocellular Carcinoma (CAHECA) frameworks. The accelerated brain structural connectivity framework was evaluated with stripped brain datasets from the Department of Surgery, University of North Carolina, Chapel Hill, United States. Significantly, our proposed framework is able to generates and extracts points and edges of datasets, displays nodes and edges in the datasets in form of a network and clearly maps data volume to the corresponding brain surface. Moreover, with the framework, surfaces of the dataset were

  3. ConnectViz: Accelerated Approach for Brain Structural Connectivity Using Delaunay Triangulation.

    PubMed

    Adeshina, A M; Hashim, R

    2016-03-01

    Stroke is a cardiovascular disease with high mortality and long-term disability in the world. Normal functioning of the brain is dependent on the adequate supply of oxygen and nutrients to the brain complex network through the blood vessels. Stroke, occasionally a hemorrhagic stroke, ischemia or other blood vessel dysfunctions can affect patients during a cerebrovascular incident. Structurally, the left and the right carotid arteries, and the right and the left vertebral arteries are responsible for supplying blood to the brain, scalp and the face. However, a number of impairment in the function of the frontal lobes may occur as a result of any decrease in the flow of the blood through one of the internal carotid arteries. Such impairment commonly results in numbness, weakness or paralysis. Recently, the concepts of brain's wiring representation, the connectome, was introduced. However, construction and visualization of such brain network requires tremendous computation. Consequently, previously proposed approaches have been identified with common problems of high memory consumption and slow execution. Furthermore, interactivity in the previously proposed frameworks for brain network is also an outstanding issue. This study proposes an accelerated approach for brain connectomic visualization based on graph theory paradigm using compute unified device architecture, extending the previously proposed SurLens Visualization and computer aided hepatocellular carcinoma frameworks. The accelerated brain structural connectivity framework was evaluated with stripped brain datasets from the Department of Surgery, University of North Carolina, Chapel Hill, USA. Significantly, our proposed framework is able to generate and extract points and edges of datasets, displays nodes and edges in the datasets in form of a network and clearly maps data volume to the corresponding brain surface. Moreover, with the framework, surfaces of the dataset were simultaneously displayed with the

  4. Surface Analysis of OFE-Copper X-Band Accelerating Structures and Possible Correlation to RF Breakdown Events

    SciTech Connect

    Harvey, S

    2003-10-08

    X-band accelerator structures meeting the Next Linear Collider (NLC) design requirements have been found to suffer vacuum surface damage caused by radio frequency (RF) breakdown, when processed to high electric-field gradients. Improved understanding of these breakdown events is desirable for the development of structure designs, fabrication procedures, and processing techniques that minimize structure damage. RF reflected wave analysis and acoustic sensor pickup have provided breakdowns localization in RF structures. Particle contaminations found following clean autopsy of four RF-processed travelling wave structures, have been catalogued and analyzed. Their influence on RF breakdown, as well as that of several other material-based properties, will be discussed.

  5. Design, realization and test of C-band accelerating structures for the SPARC_LAB linac energy upgrade

    NASA Astrophysics Data System (ADS)

    Alesini, D.; Bellaveglia, M.; Biagini, M. E.; Boni, R.; Brönnimann, M.; Cardelli, F.; Chimenti, P.; Clementi, R.; Di Pirro, G.; Di Raddo, R.; Ferrario, M.; Ficcadenti, L.; Gallo, A.; Kalt, R.; Lollo, V.; Palumbo, L.; Piersanti, L.; Schilcher, T.

    2016-11-01

    The energy upgrade of the SPARC_LAB photo-injector at LNF-INFN (Frascati, Italy) has been originally conceived replacing one low gradient (13 MV/m) 3 m long SLAC type S-band traveling wave (TW) section with two 1.4 m long C-band accelerating sections. Due to the higher gradients reached by such structures, a higher energy beam can be obtained within the same accelerator footprint length. The use of C-band structures for electron acceleration has been adopted in a few FEL linacs in the world, among others, the Japanese Free Electron Laser at SPring-8 and the SwissFEL at Paul Scherrer Institute (PSI). The C-band sections are traveling wave, constant impedance structures with symmetric input and output axial couplers. Their design has been optimized for the operation with a SLED RF pulse compressor. In this paper we briefly review their design criteria and we focus on the construction, tuning, low and high-power RF tests. We also illustrate the design and realization of the dedicated low level RF system that has been done in collaboration with PSI in the framework of the EU TIARA project. Preliminary experimental results appear to confirm the operation of such structures with accelerating gradients larger than 35 MV/m.

  6. Ion Acceleration at Earth, Saturn and Jupiter and its Global Impact on Magnetospheric Structure

    NASA Astrophysics Data System (ADS)

    Brandt, Pontus

    2016-07-01

    The ion plasma pressures at Earth, Saturn and Jupiter are significant players in the electrodynamic force-balance that governs the structure and dynamics of these magnetospheres. There are many similarities between the physical mechanisms that are thought to heat the ion plasma to temperatures that even exceed those of the solar corona. In this presentation we compare the ion acceleration mechanisms at the three planetary magnetospheres and discuss their global impacts on magnetopsheric structure. At Earth, bursty-bulk flows, or "bubbles", have been shown to accelerate protons and O+ to high energies by the earthward moving magnetic dipolarization fronts. O+ ions display a more non-adiabatic energization in response to these fronts than protons do as they are energized and transported in to the ring-current region where they reach energies of several 100's keV. We present both in-situ measurements from the NASA Van Allen Probes Mission and global Energetic Neutral (ENA) images from the High-Energy Neutral Atom (HENA) Camera on board the IMAGE Mission, that illustrate these processes. The global impact on the magnetospheric structure is explored by comparing the empirical magnetic field model TS07d for given driving conditions with global plasma pressure distributions derived from the HENA images. At Saturn, quasi-periodic energization events, or large-scale injections, occur beyond about 9 RS around the post-midnight sector, clearly shown by the Ion and Neutral Atom Camera (INCA) on board the Cassini mission. In contrast to Earth, the corotational drift dominates even the energetic ion distributions. The large-scale injections display similar dipolarization front features can be found and there are indications that like at Earth the O+ responds more non-adiabatically than protons do. However, at Saturn there are also differences in that there appears to be energization events deep in the inner magnetosphere (6-9 RS) preferentially occurring in the pre

  7. FACET ORIENTATION AND TROPISM: ASSOCIATION WITH ACCELERATED DEGENERATION OF STABILIZING STRUCTURES IN LOWER LUMBAR SPINE.

    PubMed

    Jelec, Vjekoslav; Turner, Rajka; Franić, Miljenko; Korušić, Anđelko; Rotim, Krešimir

    2016-03-01

    The influence of facet orientation and tropism on the process of spinal degeneration has been extensively studied during the last few decades, but there are still many controversies and conflicting results in this field of research. The biomechanical cause of accelerated degeneration of stabilizing structures in lower lumbar spine lies within the combination of several factors, but two most important ones are compressive load and more coronal facet orientation that offers less resistance against torsional loading. Axial rotation of lower lumbar spine is undoubtedly associated with higher strain in disc annulus, and enhanced range of secondary rotational movements may be even more significant for the progression of annular degeneration. Accordingly, more pronounced facet tropism could be having part in faster progression of disc degeneration in lower lumbar spine, as indicated by a number of recent studies. More sagittal facet orientation in patients with a higher facet osteoarthritis score at lower lumbar segments is very likely related to arthritic remodeling commonly seen in other synovial joints. There is also a possibility that it could be associated with the adaptation to partial loss of lumbar lordosis, as both coincide with advanced age.

  8. Accelerated Life Structural Benchmark Testing for a Stirling Convertor Heater Head

    NASA Technical Reports Server (NTRS)

    Krause, David L.; Kantzos, Pete T.

    2006-01-01

    For proposed long-duration NASA Space Science missions, the Department of Energy, Lockheed Martin, Infinia Corporation, and NASA Glenn Research Center are developing a high-efficiency, 110 W Stirling Radioisotope Generator (SRG110). A structurally significant limit state for the SRG110 heater head component is creep deformation induced at high material temperature and low stress level. Conventional investigations of creep behavior adequately rely on experimental results from uniaxial creep specimens, and a wealth of creep data is available for the Inconel 718 material of construction. However, the specified atypical thin heater head material is fine-grained with a heat treatment that limits precipitate growth, and little creep property data for this microstructure is available in the literature. In addition, the geometry and loading conditions apply a multiaxial stress state on the component, far from the conditions of uniaxial testing. For these reasons, an extensive experimental investigation is ongoing to aid in accurately assessing the durability of the SRG110 heater head. This investigation supplements uniaxial creep testing with pneumatic testing of heater head-like pressure vessels at design temperature with stress levels ranging from approximately the design stress to several times that. This paper presents experimental results, post-test microstructural analyses, and conclusions for four higher-stress, accelerated life tests. Analysts are using these results to calibrate deterministic and probabilistic analytical creep models of the SRG110 heater head.

  9. Structural Shielding Design of a 6 MV Flattening Filter Free Linear Accelerator: Indian Scenario.

    PubMed

    Mishra, Bibekananda; Selvam, T Palani; Sharma, P K Dash

    2017-01-01

    Detailed structural shielding of primary and secondary barriers for a 6 MV medical linear accelerator (LINAC) operated with flattening filter (FF) and flattening filter free (FFF) modes are calculated. The calculations have been carried out by two methods, one using the approach given in National Council on Radiation Protection (NCRP) Report No. 151 and the other based on the monitor units (MUs) delivered in clinical practice. Radiation survey of the installations was also carried out. NCRP approach suggests that the primary and secondary barrier thicknesses are higher by 24% and 26%. respectively, for a LINAC operated in FF mode to that of a LINAC operated in both FF and FFF modes with an assumption that only 20% of the workload is shared in FFF mode. Primary and secondary barrier thicknesses calculated from MUs delivered on clinical practice method also show the same trend and are higher by 20% and 19%, respectively, for a LINAC operated in FF mode to that of a LINAC operated in both FF and FFF modes. Overall, the barrier thickness for a LINAC operated in FF mode is higher about 20% to that of a LINAC operated in both FF and FFF modes.

  10. Accelerated Life Structural Benchmark Testing for a Stirling Convertor Heater Head

    SciTech Connect

    Krause, David L.; Kantzos, Pete T.

    2006-01-20

    For proposed long-duration NASA Space Science missions, the Department of Energy, Lockheed Martin, Infinia Corporation, and NASA Glenn Research Center are developing a high-efficiency, 110-watt Stirling Radioisotope Generator (SRG110). A structurally significant limit state for the SRG110 heater head component is creep deformation induced at high material temperature and low stress level. Conventional investigations of creep behavior adequately rely on experimental results from uniaxial creep specimens, and a wealth of creep data is available for the Inconel 718 material of construction. However, the specified atypical thin heater head material is fine-grained with a heat treatment that limits precipitate growth, and little creep property data for this microstructure is available in the literature. In addition, the geometry and loading conditions apply a multiaxial stress state on the component, far from the conditions of uniaxial testing. For these reasons, an extensive experimental investigation is ongoing to aid in accurately assessing the durability of the SRG110 heater head. This investigation supplements uniaxial creep testing with pneumatic testing of heater head-like pressure vessels at design temperature with stress levels ranging from approximately the design stress to several times that. This paper presents experimental results, post-test microstructural analyses, and conclusions for four higher-stress, accelerated life tests. Analysts are using these results to calibrate deterministic and probabilistic analytical creep models of the SRG110 heater head.

  11. Magnetic and Structural Design of a 15 T $Nb_3Sn$ Accelerator Depole Model

    SciTech Connect

    Kashikhin, V. V.; Andreev, N.; Barzi, E.; Novitski, I.; Zlobin, A. V.

    2015-01-01

    Hadron Colliders (HC) are the most powerful discovery tools in modern high energy physics. A 100 TeV scale HC with a nominal operation field of at least 15 T is being considered for the post-LHC era. The choice of a 15 T nominal field requires using the Nb3Sn technology. Practical demonstration of this field level in an accelerator-quality magnet and substantial reduction of the magnet costs are the key conditions for realization of such a machine. FNAL has started the development of a 15 T $Nb_{3}Sn$ dipole demonstrator for a 100 TeV scale HC. The magnet design is based on 4-layer shell type coils, graded between the inner and outer layers to maximize the performance. The experience gained during the 11-T dipole R&D campaign is applied to different aspects of the magnet design. This paper describes the magnetic and structural designs and parameters of the 15 T $Nb_3Sn$ dipole and the steps towards the demonstration model.

  12. Structural Shielding Design of a 6 MV Flattening Filter Free Linear Accelerator: Indian Scenario

    PubMed Central

    Mishra, Bibekananda; Selvam, T. Palani; Sharma, P. K. Dash

    2017-01-01

    Detailed structural shielding of primary and secondary barriers for a 6 MV medical linear accelerator (LINAC) operated with flattening filter (FF) and flattening filter free (FFF) modes are calculated. The calculations have been carried out by two methods, one using the approach given in National Council on Radiation Protection (NCRP) Report No. 151 and the other based on the monitor units (MUs) delivered in clinical practice. Radiation survey of the installations was also carried out. NCRP approach suggests that the primary and secondary barrier thicknesses are higher by 24% and 26%. respectively, for a LINAC operated in FF mode to that of a LINAC operated in both FF and FFF modes with an assumption that only 20% of the workload is shared in FFF mode. Primary and secondary barrier thicknesses calculated from MUs delivered on clinical practice method also show the same trend and are higher by 20% and 19%, respectively, for a LINAC operated in FF mode to that of a LINAC operated in both FF and FFF modes. Overall, the barrier thickness for a LINAC operated in FF mode is higher about 20% to that of a LINAC operated in both FF and FFF modes. PMID:28405104

  13. Accelerated Life Structural Benchmark Testing for a Stirling Convertor Heater Head

    NASA Astrophysics Data System (ADS)

    Krause, David L.; Kantzos, Pete T.

    2006-01-01

    For proposed long-duration NASA Space Science missions, the Department of Energy, Lockheed Martin, Infinia Corporation, and NASA Glenn Research Center are developing a high-efficiency, 110-watt Stirling Radioisotope Generator (SRG110). A structurally significant limit state for the SRG110 heater head component is creep deformation induced at high material temperature and low stress level. Conventional investigations of creep behavior adequately rely on experimental results from uniaxial creep specimens, and a wealth of creep data is available for the Inconel 718 material of construction. However, the specified atypical thin heater head material is fine-grained with a heat treatment that limits precipitate growth, and little creep property data for this microstructure is available in the literature. In addition, the geometry and loading conditions apply a multiaxial stress state on the component, far from the conditions of uniaxial testing. For these reasons, an extensive experimental investigation is ongoing to aid in accurately assessing the durability of the SRG110 heater head. This investigation supplements uniaxial creep testing with pneumatic testing of heater head-like pressure vessels at design temperature with stress levels ranging from approximately the design stress to several times that. This paper presents experimental results, post-test microstructural analyses, and conclusions for four higher-stress, accelerated life tests. Analysts are using these results to calibrate deterministic and probabilistic analytical creep models of the SRG110 heater head.

  14. Influence of solidification accelerators on structure formation of anhydrite-containing binders

    SciTech Connect

    Anikanova, L. Volkova, O. Kudyakov, A.; Sarkisov, Y.; Tolstov, D.

    2016-01-15

    The article presents results of scientific analysis of chemical additives influence on acid fluoride binder. It was found that the influence of sulfate nature additives on the process of hydration and solidification of the binder is similar to influence of additives on indissoluble anhydrite. Additives with SO{sub 4}{sup 2−} anion NO{sup −} are more efficient. The mentioned additives according to accelerating effect belong to the following succession: K{sub 2}SO{sub 4} > Na{sub 2}SO{sub 4} > FeSO{sub 4} > MgSO{sub 4}. Facilitation of the process of hydration and solidification of the binder, increase in density and durability of the binder (32 MPa) is to the greatest extent achieved with the introduction of 2% sodium sulfate additive of the binder’s mass into the composition of the binder along with the ultrasonic treatment of water solution. Directed crystal formation process with healing of porous structure by new growths presented as calcium sulfate dehydrate and hydroglauberite provides positive effect.

  15. GPU-accelerated model for fast, three-dimensional fluid-structure interaction computations.

    PubMed

    Nita, Cosmin; Itu, Lucian; Mihalef, Viorel; Sharma, Puneet; Rapaka, Saikiran

    2015-08-01

    In this paper we introduce a methodology for performing one-way Fluid-Structure interaction (FSI), i.e. where the motion of the wall boundaries is imposed. We use a Graphics Processing Unit (GPU) accelerated Lattice-Boltzmann Method (LBM) implementation and present an efficient workflow for embedding the moving geometry, given as a set of polygonal meshes, in the LBM computation. The proposed method is first validated in a synthetic experiment: a vessel which is periodically expanding and contracting. Next, the evaluation focuses on the 3D Peristaltic flow problem: a fluid flows inside a flexible tube, where a periodic wave-like deformation produces a fluid motion along the centerline of the tube. Different geometry configurations are used and results are compared against previously published solutions. The efficient approach leads to an average execution time of approx. one hour per computation, whereas 50% of it is required for the geometry update operations. Finally, we also analyse the effect of changing the Reynolds number on the flow streamlines: the flow regime is significantly affected by the Reynolds number.

  16. Impact of a flattening filter free linear accelerator on structural shielding design.

    PubMed

    Jank, Julia; Kragl, Gabriele; Georg, Dietmar

    2014-03-01

    The present study aimed to assess the effects of a flattening filter free medical accelerator on structural shielding demands of a treatment vault of a medical linear accelerator. We tried to answer the question, to what extent the required thickness of the shielding barriers can be reduced if instead of the standard flattened photon beams unflattened ones are used. We chose both an experimental as well as a theoretical approach. On the one hand we measured photon dose rates at protected places outside the treatment room and compared the obtained results for flattened and unflattened beams. On the other hand we complied with international guidelines for adequate treatment vault design and calculated the shielding barriers according to the therein given specifications. Measurements were performed with an Elekta Precise™ linac providing nominal photon energies of 6 and 10 MV. This machine underwent already earlier some modifications in order to be able to operate both with and without a flattening filter. Photon dose rates were measured with a LB133-1 dose rate meter manufactured by Berthold. To calculate the thickness of shielding barriers we referred to the Austrian standard ÖNORM S 5216 and to the US American NCRP Report No. 151. We determined a substantial photon dose rate reduction for all measurement points and photon energies. For unflattened 6 MV beams a reduction factor ranging from 1.4 to 1.8 was identified. The corresponding values for unflattened 10 MV beams were 2.1 and 3.2. The performed shielding calculations indicated the same tendency: For all relevant radiation components we found a reduction in shielding thickness when unflattened beams were used. The required thickness of primary barriers was reduced up to 8.0%, the thickness of secondary barriers up to 11.4%, respectively. For an adequate dimensioning of treatment vault shielding barriers it is by no means irrelevant if the accommodated linac operates with or without a flattening filter. The

  17. Accelerated contrast-enhanced whole-heart coronary MRI using low-dimensional-structure self-learning and thresholding.

    PubMed

    Akçakaya, Mehmet; Basha, Tamer A; Chan, Raymond H; Rayatzadeh, Hussein; Kissinger, Kraig V; Goddu, Beth; Goepfert, Lois A; Manning, Warren J; Nezafat, Reza

    2012-05-01

    We sought to evaluate the efficacy of prospective random undersampling and low-dimensional-structure self-learning and thresholding reconstruction for highly accelerated contrast-enhanced whole-heart coronary MRI. A prospective random undersampling scheme was implemented using phase ordering to minimize artifacts due to gradient switching and was compared to a randomly undersampled acquisition with no profile ordering. This profile-ordering technique was then used to acquire contrast-enhanced whole-heart coronary MRI in 10 healthy subjects with 4-fold acceleration. Reconstructed images and the acquired zero-filled images were compared for depicted vessel length, vessel sharpness, and subjective image quality on a scale of 1 (poor) to 4 (excellent). In a pilot study, contrast-enhanced whole-heart coronary MRI was also acquired in four patients with suspected coronary artery disease with 3-fold acceleration. The undersampled images were reconstructed using low-dimensional-structure self-learning and thresholding, which showed significant improvement over the zero-filled images in both objective and subjective measures, with an overall score of 3.6 ± 0.5. Reconstructed images in patients were all diagnostic. Low-dimensional-structure self-learning and thresholding reconstruction allows contrast-enhanced whole-heart coronary MRI with acceleration as high as 4-fold using clinically available five-channel phased-array coil. Copyright © 2012 Wiley Periodicals, Inc.

  18. Neutron field of accelerator-driven p(35 MeV)+Be fast neutron source at NPI Rez

    NASA Astrophysics Data System (ADS)

    Stefanik, Milan; Bem, Pavel; Majerle, Mitja; Novak, Jan; Simeckova, Eva

    2017-09-01

    The accelerator driven fast neutron sources of the white- and quasi-monoenergetic spectra are operated at the NPI Rez Fast Neutron Facility utilizing the Be(thick), D2O(thick), and 7Li(C) target stations and the variable energy proton beam (up to 37 MeV) from the U-120M isochronous cyclotron. Recently, the design of beryllium target station was upgraded in order to provide the higher neutron flux at the modified positions of irradiated samples. Afterwards, the thick target neutron field of the p+Be source reaction was investigated for proton energy of 35 MeV. The spectral neutron flux for several target-to-sample distances was determined using the multi-foil activation technique. From measured reaction rates, new neutron spectra were reconstructed employing the SAND-II unfolding code and validated against the MCNPX predictions. The IFMIF-like (International Fusion Material Irradiation Facility) neutron field obtained from the p(35)+Be source is suitable for the neutron cross-sections validation within the IFMIF research program, radiation hardness tests of electronics, and neutron activation analysis experiments.

  19. A Study of Higher-Band Dipole Wakefields in X-Band Accelerating Structures for the G/NLC

    SciTech Connect

    Jones, R

    2004-09-02

    The X-band linacs for the G/NLC (Global/Next Linear Collider) have evolved from the DDS (Damped Detuned Structure) series. The present accelerating structures are 60 cm in length and incorporate damping and detuning of the dipole modes which comprise the wakefield. In order to adequately damp the wakefield, frequencies of adjacent structures are interleaved. Limited analysis has been done previously on the higher order dipole bands. Here, we calculate the contribution of higher order bands of interleaved structures to the wakefield. Beam dynamics issues are also studied.

  20. PROPERTIES OF THE ACCELERATION REGIONS IN SEVERAL LOOP-STRUCTURED SOLAR FLARES

    SciTech Connect

    Guo Jingnan; Piana, Michele; Gordon Emslie, A.; Massone, Anna Maria E-mail: piana@dima.unige.it E-mail: annamaria.massone@cnr.it

    2012-08-10

    Using RHESSI hard X-ray imaging spectroscopy observations, we analyze electron flux maps for a number of extended coronal loop flares. For each event, we fit a collisional model with an extended acceleration region to the observed variation of loop length with electron energy E, resulting in estimates of the plasma density in, and longitudinal extent of, the acceleration region. These quantities in turn allow inference of the number of particles within the acceleration region and hence the filling factor f-the ratio of the emitting volume to the volume that encompasses the emitting region(s). We obtain values of f that lie mostly between 0.1 and 1.0; the (geometric) mean value is f = 0.20 Multiplication-Sign / Division-Sign 3.9, somewhat less than, but nevertheless consistent with, unity. Further, coupling information on the number of particles in the acceleration region with information on the total rate of acceleration of particles above a certain reference energy (obtained from spatially integrated hard X-ray data) also allows inference of the specific acceleration rate (electron s{sup -1} per ambient electron above the chosen reference energy). We obtain a (geometric) mean value of the specific acceleration rate {eta}(20 keV) =(6.0 Multiplication-Sign / Division-Sign 3.4) Multiplication-Sign 10{sup -3} electrons s{sup -1} per ambient electron; this value has implications both for the global electrodynamics associated with replenishment of the acceleration region and for the nature of the particle acceleration process.

  1. Schooling in Times of Acceleration

    ERIC Educational Resources Information Center

    Buddeberg, Magdalena; Hornberg, Sabine

    2017-01-01

    Modern societies are characterised by forms of acceleration, which influence social processes. Sociologist Hartmut Rosa has systematised temporal structures by focusing on three categories of social acceleration: technical acceleration, acceleration of social change, and acceleration of the pace of life. All three processes of acceleration are…

  2. Schooling in Times of Acceleration

    ERIC Educational Resources Information Center

    Buddeberg, Magdalena; Hornberg, Sabine

    2017-01-01

    Modern societies are characterised by forms of acceleration, which influence social processes. Sociologist Hartmut Rosa has systematised temporal structures by focusing on three categories of social acceleration: technical acceleration, acceleration of social change, and acceleration of the pace of life. All three processes of acceleration are…

  3. An introduction to acceleration mechanisms

    SciTech Connect

    Palmer, R.B.

    1987-05-01

    This paper discusses the acceleration of charged particles by electromagnetic fields, i.e., by fields that are produced by the motion of other charged particles driven by some power source. The mechanisms that are discussed include: Ponderamotive Forces, Acceleration, Plasma Beat Wave Acceleration, Inverse Free Electron Laser Acceleration, Inverse Cerenkov Acceleration, Gravity Acceleration, 2D Linac Acceleration and Conventional Iris Loaded Linac Structure Acceleration. (LSP)

  4. Magnetized Plasma-filled Waveguide: A New High-Gradient Accelerating Structure

    SciTech Connect

    Avitzour, Yoav; Shvets, Gennady

    2009-01-22

    Electromagnetic waves confined between the metal plates of a plasma-filled waveguide are investigated. It is demonstrated that when the plasma is magnetized along the metallic plates, there exists a luminous accelerating wave propagating with a very slow group velocity. It is shown that the magnetized plasma 'isolates' the metal wall from the transverse electric field, thereby reducing potential breakdown problems. Applications of the metallic plasma-filled waveguide to particle accelerations and microwave pulse manipulation are described.

  5. Highly symmetric interfacial coherent structures in Rayleigh Taylor instability with time-dependent acceleration

    NASA Astrophysics Data System (ADS)

    Bhowmick, Aklant K.; Abarzhi, Snezhana

    2016-11-01

    Rayleigh Taylor instability in a power-law time dependent acceleration field is investigated theoretically for a flow with the symmetry group p6mm (hexagon) in the plane normal to acceleration. In the nonlinear regime, regular asymptotic solutions form a one-parameter family. The physically significant solution is identified with the one having the fastest growth and being stable (bubble tip velocity). Two distinct regimes are identified depending on the acceleration exponent. Particularly, the RM-type regime, where the dynamics is identical to conventional RM instability and is dominated by initial conditions, and the RT-type regime where the dynamics is dominated by the acceleration term. For the latter, the time dependence has profound effects on the dynamics. In the RT non-linear regime, the time dependence has no consequence on the morphology of the bubbles; the growth rate (bubble tip velocity) evolves as power law with the exponent set by the acceleration. The solutions for a one-parameter family, and are convergent with exponential decay of Fourier amplitudes. The solutions are stable at maximum tip velocity, whereas flat bubbles are unstable, and the growth/decay of perturbations is no longer purely exponential and depends on the acceleration exponent. The work is supported by the US National Science Foundation.

  6. Highly symmetric interfacial structures in Rayleigh Taylor instability with time-dependent acceleration

    NASA Astrophysics Data System (ADS)

    Bhowmick, Aklant K.; Abarzhi, Snezhana

    2016-10-01

    Rayleigh Taylor instability in a power-law time dependent acceleration field is investigated for a flow with the symmetry group p6mm (hexagonal) in the plane normal to acceleration. The Regular asymptotic solutions form a one-parameter family and the physically significant solution is identified with the one having the fastest growth and being stable (bubble tip velocity). Two distinct regimes are identified dependent on the acceleration exponent, the RM-type regime, where the dynamics is identical to conventional RM instability and is dominated by initial conditions, and the RT-type regime where the dynamics is dominated by the acceleration term. For the latter, the time dependence has profound effects on the dynamics. In the RT non-linear regime, the time dependence has no consequence on the morphology of the bubbles but the growth rate (bubble tip velocity) evolves as power law with the exponent set by the acceleration. The solutions for a one-parameter family, and are convergent with exponential decay of Fourier amplitudes close to the physical solution. The solutions are stable at maximum tip velocity and flat bubbles are unstable, and the growth/decay of perturbations is no longer purely exponential and depends on the acceleration exponent. The work is supported by the US National Science Foundation.

  7. Guided post-acceleration of laser-driven ions by a miniature modular structure

    PubMed Central

    Kar, Satyabrata; Ahmed, Hamad; Prasad, Rajendra; Cerchez, Mirela; Brauckmann, Stephanie; Aurand, Bastian; Cantono, Giada; Hadjisolomou, Prokopis; Lewis, Ciaran L. S.; Macchi, Andrea; Nersisyan, Gagik; Robinson, Alexander P. L.; Schroer, Anna M.; Swantusch, Marco; Zepf, Matt; Willi, Oswald; Borghesi, Marco

    2016-01-01

    All-optical approaches to particle acceleration are currently attracting a significant research effort internationally. Although characterized by exceptional transverse and longitudinal emittance, laser-driven ion beams currently have limitations in terms of peak ion energy, bandwidth of the energy spectrum and beam divergence. Here we introduce the concept of a versatile, miniature linear accelerating module, which, by employing laser-excited electromagnetic pulses directed along a helical path surrounding the laser-accelerated ion beams, addresses these shortcomings simultaneously. In a proof-of-principle experiment on a university-scale system, we demonstrate post-acceleration of laser-driven protons from a flat foil at a rate of 0.5 GeV m−1, already beyond what can be sustained by conventional accelerator technologies, with dynamic beam collimation and energy selection. These results open up new opportunities for the development of extremely compact and cost-effective ion accelerators for both established and innovative applications. PMID:27089200

  8. Can delta-V be adjusted with structural and occupant restraint performance to improve prediction of chest acceleration?

    PubMed

    Gabauer, Douglas J; Gabler, Hampton C

    2008-10-01

    The purpose of this study is to investigate whether delta-V can be modified with a measure of vehicle structure performance and occupant restraint performance to better predict occupant peak chest acceleration during a frontal crash. A total of 619 full-scale frontal crash tests, with impact speeds ranging from 14 to 42 mph, were analyzed. Multiple linear regression was used to correlate combinations of crash severity, vehicle structure performance, and occupant restraint performance descriptors to the maximum measured crash test dummy chest acceleration. Using an adjusted R(2) selection method, the best combination of metrics were selected and then compared to a baseline model that used only delta-V to predict occupant chest kinematics. The combination of delta-V, ridedown efficiency, and the kinetic energy factor was found to provide the best prediction of the occupant chest acceleration. This combination accounted for approximately 4 times the variation in the maximum chest acceleration when compared to a model based solely on vehicle delta-V.

  9. The solar wind structures associated with cosmic ray decreases and particle acceleration in 1978-1982

    NASA Technical Reports Server (NTRS)

    Cane, H. V.; Richardson, I. G.; Vonrosenvinge, T. T.

    1992-01-01

    The time histories of particles in the energy range 1 MeV to 1 GeV at times of all greater than 3 percent cosmic ray decreases in the years 1978 to 1982 are studied. Essentially all 59 of the decreases commenced at or before the passages of interplanetary shocks, the majority of which accelerated energetic particles. We use the intensity-time profiles of the energetic particles to separate the cosmic ray decreases into four classes which we subsequently associate with four types of solar wind structures. Decreases in class 1 (15 events) and class 2 (26 events) can be associated with shocks which are driven by energetic coronal mass ejections. For class 1 events the ejecta is detected at 1 AU whereas this is not the case for class 2 events. The shock must therefore play a dominant role in producing the depression of cosmic rays in class 2 events. In all class 1 and 2 events (which comprise 69 percent of the total) the departure time of the ejection from the sun (and hence the location) can be determined from the rapid onset of energetic particles several days before the shock passage at Earth. The class 1 events originate from within 50 deg of central meridian. Class 3 events (10 decreases) can be attributed to less energetic ejections which are directed towards the Earth. In these events the ejecta is more important than the shock in causing a depression in the cosmic ray intensity. The remaining events (14 percent of the total) can be attributed to corotating streams which have ejecta material embedded in them.

  10. Interaction of an ultrarelativistic electron bunch train with a W-band accelerating structure: High power and high gradient

    DOE PAGES

    Wang, D.; Antipov, S.; Jing, C.; ...

    2016-02-05

    Electron beam interaction with high frequency structures (beyond microwave regime) has a great impact on future high energy frontier machines. We report on the generation of multimegawatt pulsed rf power at 91 GHz in a planar metallic accelerating structure driven by an ultrarelativistic electron bunch train. This slow-wave wakefield device can also be used for high gradient acceleration of electrons with a stable rf phase and amplitude which are controlled by manipulation of the bunch train. To achieve precise control of the rf pulse properties, a two-beam wakefield interferometry method was developed in which the rf pulse, due to themore » interference of the wakefields from the two bunches, was measured as a function of bunch separation. As a result, measurements of the energy change of a trailing electron bunch as a function of the bunch separation confirmed the interferometry method.« less

  11. Interaction of an ultrarelativistic electron bunch train with a W-band accelerating structure: High power and high gradient

    SciTech Connect

    Wang, D.; Antipov, S.; Jing, C.; Power, J. G.; Conde, M.; Wisniewski, E.; Liu, W.; Qiu, J.; Ha, G.; Dolgashev, V.; Tang, C.; Gai, W.

    2016-02-05

    Electron beam interaction with high frequency structures (beyond microwave regime) has a great impact on future high energy frontier machines. We report on the generation of multimegawatt pulsed rf power at 91 GHz in a planar metallic accelerating structure driven by an ultrarelativistic electron bunch train. This slow-wave wakefield device can also be used for high gradient acceleration of electrons with a stable rf phase and amplitude which are controlled by manipulation of the bunch train. To achieve precise control of the rf pulse properties, a two-beam wakefield interferometry method was developed in which the rf pulse, due to the interference of the wakefields from the two bunches, was measured as a function of bunch separation. As a result, measurements of the energy change of a trailing electron bunch as a function of the bunch separation confirmed the interferometry method.

  12. Interaction of an Ultrarelativistic Electron Bunch Train with a W -Band Accelerating Structure: High Power and High Gradient

    NASA Astrophysics Data System (ADS)

    Wang, D.; Antipov, S.; Jing, C.; Power, J. G.; Conde, M.; Wisniewski, E.; Liu, W.; Qiu, J.; Ha, G.; Dolgashev, V.; Tang, C.; Gai, W.

    2016-02-01

    Electron beam interaction with high frequency structures (beyond microwave regime) has a great impact on future high energy frontier machines. We report on the generation of multimegawatt pulsed rf power at 91 GHz in a planar metallic accelerating structure driven by an ultrarelativistic electron bunch train. This slow-wave wakefield device can also be used for high gradient acceleration of electrons with a stable rf phase and amplitude which are controlled by manipulation of the bunch train. To achieve precise control of the rf pulse properties, a two-beam wakefield interferometry method was developed in which the rf pulse, due to the interference of the wakefields from the two bunches, was measured as a function of bunch separation. Measurements of the energy change of a trailing electron bunch as a function of the bunch separation confirmed the interferometry method.

  13. IMPEDANCE MEASUREMENT SETUP FOR HIGHER-ORDER MODE STUDIES IN NLC ACCELERATING STRUCTURES WITH THE WIRE METHOD

    SciTech Connect

    Baboi, Nicoleta

    2002-09-19

    Dipole modes are the main cause of transverse emittance dilution in the Japanese Linear Collider/Next Linear Collider (JLC/NLC). A diagnostic setup has been built in order to investigate them. The method is based on using a coaxial wire to excite and measure electromagnetic modes of accelerating structures. This method can offer a more efficient and less expensive procedure than the ASSET facility. Initial measurements have been made and are presented in this paper.

  14. Superconducting accelerating structure for particle velocities from 0. 12 to 0. 23 c

    SciTech Connect

    Shepard, K.W.; Zinkann, G.P.

    1983-01-01

    A split-ring resonator has been designed for an optimum particle velocity ..beta.. = v/c = 0.16 and a frequency of 145.5 MHz. The ratio of peak-surface electric field to effective accelerating field in the resonator has been reduced 20% from the value obtained in previously developed split-ring resonators. The improved design results from the use of elliptically-sectioned loading arms and drift tubes, which have been enlarged to reduce peak-surface fields and also shaped to eliminate beam-steering effects in the resonator. All fabrication problems presented by the more-complex geometry have been solved, and a prototype superconducting niobium resonator has been completed. An accelerating field of 3.3 MV/m at 4 watts rf input has been so far achieved, corresponding to an effective accelerating potential of 1.17 MV per resonator.

  15. Design study of high gradient, low impedance accelerating structures for the FERMI free electron laser linac upgrade

    NASA Astrophysics Data System (ADS)

    Shafqat, N.; Di Mitri, S.; Serpico, C.; Nicastro, S.

    2017-09-01

    The FERMI free-electron laser (FEL) of Elettra Sincrotrone Trieste, Italy, is a user facility driven by a 1.5 GeV 10-50 Hz S-band radiofrequency linear accelerator (linac), and it is based on an external laser seeding scheme that allows lasing at the shortest fundamental wavelength of 4 nm. An increase of the beam energy to 1.8 GeV at a tolerable breakdown rate, and an improvement of the final beam quality is desired in order to allow either lasing at 4 nm with a higher flux, or lasing at shorter wavelengths. This article presents the impedance analysis of newly designed S-band accelerating structures, for replacement of the existing backward travelling wave structures (BTWS) in the last portion of the FERMI linac. The new structure design promises higher accelerating gradient and lower impedance than those of the existing BTWS. Particle tracking simulations show that, with the linac upgrade, the beam relative energy spread, its linear and nonlinear z-correlation internal to the bunch, and the beam transverse emittances can be made smaller than the ones in the present configuration, with expected advantage to the FEL performance. The repercussion of the upgrade on the linac quadrupole magnets setting, for a pre-determined electron beam optics, is also considered.

  16. Success Structure for Accelerated Acquisition of English by Young ESL Learners

    ERIC Educational Resources Information Center

    Mohamed, Abdul Rashid; Tumin, Mahani; Omar, Hamzah

    2008-01-01

    This is an investigation into the accelerated acquisition of English among young ESL learners in an International School. It employed an ethnographic case study approach where data were gathered through non-participant observations, unstructured interviews, relevant documents, students' portfolios, field notes and biographical details. The sample…

  17. 805 MHz Beta = 0.47 Elliptical Accelerating Structure R & D

    SciTech Connect

    S. Bricker; C. Compton; W. Hartung; M. Johnson; F. Marti; J. Popierlarski; R. C. York; et al

    2008-09-22

    A 6-cell 805 MHz superconducting cavity for acceleration in the velocity range of about 0.4 to 0.53 times the speed of light was designed. After single-cell prototyping, three 6-cell niobium cavities were fabricated. In vertical RF tests of the 6-cell cavities, the measured quality factors (Q{sub 0}) were between 7 {center_dot} 10{sup 9} and 1.4 {center_dot} 10{sup 10} at the design field (accelerating gradient of 8 to 10 MV/m). A rectangular cryomodule was designed to house 4 cavities per cryomodule. The 4-cavity cryomodule could be used for acceleration of ions in a linear accelerator, with focusing elements between the cryomodules. A prototype cryomodule was fabricated to test 2 cavities under realistic operating conditions. Two of the 6-cell cavities were equipped with helium tanks, tuners, and input coupler and installed into the cryomodule. The prototype cryomodule was used to verify alignment, electromagnetic performance, frequency tuning, cryogenic performance, low-level RF control, and control of microphonics.

  18. X-band accelerator structures: On going R&D at the INFN

    NASA Astrophysics Data System (ADS)

    Gatti, G.; Marcelli, A.; Spataro, B.; Dolgashev, V.; Lewandowski, J.; Tantawi, S. G.; Yeremian, A. D.; Higashi, Y.; Rosenzweig, J.; Sarti, S.; Caliendo, C.; Castorina, G.; Cibin, G.; Carfora, L.; Leonardi, O.; Rigato, V.; Campostrini, M.

    2016-09-01

    The next generation of accelerators, from the compact to the large infrastructure dedicated to high energy physics, is highly demanding in terms of accelerating gradients. To upgrade performances of X band linacs at 11.424 GHz many resources are devoted to achieve high accelerating gradients and at the same time to obtain a high reliability. In the framework of a three-year funded project by the Vth Committee of the INFN to the Laboratori Nazionali di Frascati (LNF) and to the Laboratori Nazionali di Legnaro (LNL). Within a broad international collaboration the LNF has been involved in the design, manufacture and test of compact high power standing wave (SW) sections operating at high frequency while LNL is actively involved in the development of new materials and multilayers using PVD (Physical Vapor Deposition) methods. We will report about the status of the accelerating device and of the different ongoing R&D activities and characterization procedures such as tests of different materials and metallic coatings.

  19. Measurements of ultimate accelerating gradients in the SLAC disk-loaded structure. Part I

    SciTech Connect

    Wang, J.W.; Loew, G.A.

    1985-01-01

    The work reported here describes measurements made to study the maximum attainable accelerating gradients in a conventional SLAC disk-loaded accelerator section of the constant-gradient type running at 2856 MHz. The objective was to reach an accelerating gradient of at least 100 MV/m. The accelerating gradient at which the SLAC disk-loaded waveguide runs routinely is approx. 9 MV/m (36 MW tubes without SLED) and approx. 12 MV/m with SLED I (2.5 ..mu..sec pulse). To reach 100 MV/m in a conventional 3 m constant-gradient section, one would need a klystron with a peak power output of 900 MW. since such a tube is not available, we decided to use a short standing-wave section in which the resonant fields would be allowed to build up. The design criteria for this section, the fabrication, matching and tuning, the experimental set-up and the results are described below.

  20. Development of millimeter-wave accelerating structures using precision metal forming technology

    SciTech Connect

    2003-06-03

    High gradients in radio-frequency (RF) driven accelerators require short wavelengths that have the concomitant requirements of small feature size and high tolerances, 1-2 {micro}m for millimeter wavelengths. Precision metal-forming stampling has the promise of meeting those tolerances with high production rates. This STI will evaluate that promise.

  1. Evolution of structure and properties of VVER-1000 RPV steels under accelerated irradiation up to beyond design fluences

    NASA Astrophysics Data System (ADS)

    Gurovich, B.; Kuleshova, E.; Shtrombakh, Ya.; Fedotova, S.; Maltsev, D.; Frolov, A.; Zabusov, O.; Erak, D.; Zhurko, D.

    2015-01-01

    In this paper comprehensive studies of structure and properties of VVER-1000 RPV steels after the accelerated irradiation to fluences corresponding to extended lifetime up to 60 years or more as well as comparative studies of materials irradiated with different fluxes were carried out. The significant flux effect is confirmed for the weld metal (nickel concentration ⩾1.35%) which is mainly due to development of reversible temper brittleness. The rate of radiation embrittlement of VVER-1000 RPV steels under operation up to 60 years and more (based on the results of accelerated irradiation considering flux effect for weld metal) is expected not to differ significantly from the observed rate under irradiation within surveillance specimens.

  2. Gas density structure of supersonic flows impinged on by thin blades for laser-plasma accelerators

    NASA Astrophysics Data System (ADS)

    Mao, H.-S.; Swanson, K. K.; Tsai, H.-E.; Barber, S. K.; Steinke, S.; van Tilborg, J.; Geddes, C. G. R.; Leemans, W. P.

    2017-03-01

    Density transition injection is an effective technique for controllably loading electrons into a trapped phase for laser-plasma accelerators. One common technique to achieve this fluid phenomenon is to impinge a thin blade on the plume of a supersonic nozzle. 2-D simulations show that the density transition accessible to a transverse laser is produced by a rapid re-expansion of the high pressure region behind the initial bow shock, and not by the bow shock produced by the blade, as is commonly thought. This pressure mismatched re-expansion generates compression waves that could coalesce into shock-fronts as they interact with the surrounding ambient gas. This has consequences when interpreting the electron injection mechanism. In the simulations presented here, the fluid dynamics of a supersonic nozzle impinged on by a thin, flat object is explored, along with the implications for electron beam injectors in laser-plasma accelerators.

  3. Electron Acceleration and Structure in the Quasi-perpendicular Collisionless Shock

    SciTech Connect

    Burgess, D.

    2005-08-01

    Electron acceleration at quasi-perpendicular shocks is a key problem in collisionless shock physics, in the context of the Earth's bow shock and other astrophysical situations. Fast Fermi acceleration, or reflection by adiabatic mirroring is a robust mechanism, but predicts that the highest energies are produced over a very small shock angle range, close to perpendicular where the reflected flux is decreasingly small. Pitch angle scattering has been shown to be effective in broadening the parameter range where this process is important. Using 2D hybrid simulations and electron test particle simulations, we show that ripples and oscillations of the shock surface are efficient scatters of suprathermal electrons. The results indicate that power law energy distributions can be obtained for both upstream and downstream energetic electrons, over a reasonably wide range of shock angles.

  4. Application of Rate Theory to Accelerated Durability Testing of Structural Adhesives

    DTIC Science & Technology

    1980-03-01

    comes too late to impact on material selection or design considerations. The analytical approach, coupled with an accelerated 10 testing program, is...estimated range and then evaluating the impact of each parameter on the failure rate and expected service life. The life-limiting components and the...interest of processing economy can be identified. This information can then be fed back into the system design process and the analyses repeated to

  5. The Effects of High Sustained Acceleration on the Acoustic Phonetic Structure of Speech. A Preliminary Investigation.

    DTIC Science & Technology

    1986-05-21

    displacement of the articulators. The effect is most clearly present for the second formant which is traditionally associated with tongue advancement. Diphthong...words produced at 1 G in both spectral and durational characteristics. The formant shifts observed were similar for both speakers. The first formant ...increased for the majority of vowels. The second formant tended to be lower for the front vowels /i, J/ and higher for the back vowel (u). Acceleration

  6. Strong current sheet at a magnetosheath jet: Kinetic structure and electron acceleration

    NASA Astrophysics Data System (ADS)

    Eriksson, E.; Vaivads, A.; Graham, D. B.; Khotyaintsev, Yu. V.; Yordanova, E.; Hietala, H.; André, M.; Avanov, L. A.; Dorelli, J. C.; Gershman, D. J.; Giles, B. L.; Lavraud, B.; Paterson, W. R.; Pollock, C. J.; Saito, Y.; Magnes, W.; Russell, C.; Torbert, R.; Ergun, R.; Lindqvist, P.-A.; Burch, J.

    2016-10-01

    Localized kinetic-scale regions of strong current are believed to play an important role in plasma thermalization and particle acceleration in turbulent plasmas. We present a detailed study of a strong localized current, 4900 nA m-2, located at a fast plasma jet observed in the magnetosheath downstream of a quasi-parallel shock. The thickness of the current region is ˜3 ion inertial lengths and forms at a boundary separating magnetosheath-like and solar wind-like plasmas. On ion scales the current region has the shape of a sheet with a significant average normal magnetic field component but shows strong variations on smaller scales. The dynamic pressure within the magnetosheath jet is over 3 times the solar wind dynamic pressure. We suggest that the current sheet is forming due to high velocity shears associated with the jet. Inside the current sheet we observe local electron acceleration, producing electron beams, along the magnetic field. However, there is no clear sign of ongoing reconnection. At higher energies, above the beam energy, we observe a loss cone consistent with part of the hot magnetosheath-like electrons escaping into the colder solar wind-like plasma. This suggests that the acceleration process within the current sheet is similar to the one that occurs at shocks, where electron beams and loss cones are also observed. Therefore, electron beams observed in the magnetosheath do not have to originate from the bow shock but can also be generated locally inside the magnetosheath.

  7. Optimization of radiation acceleration regime and the target structure in laser plasma interaction

    NASA Astrophysics Data System (ADS)

    Dudnikova, Galina; Lui, Chuan; Papadopoulos, Dennis; Sagdeev, Roald; Zigler, Ari

    2009-11-01

    Recent work [1,2] indicates that under proper conditions the interaction of ultra-short, high power lasers with thin foils can generate ion beams in the 100-200 MeV energy range with relatively low velocity dispersion. This technology can have major implications to medical ion proton cancer therapy since it can provide a relatively inexpensive table-top alternative to the current used traditional cyclotrons. This paper presents a simulation trade-off study of laser driven generation of quasi-monochromatic ion beams in the thin-foil Radiation Pressure Acceleration (RPA) regime. The radiation pressure accelerates the electron cloud, which in its turn transfers accelerates the ions due to the induced longitudinal charge separation fields. A series of two and three-dimensional PIC simulations are presented with emphasis on stabilizing the target plasma against Raleigh-Taylor and modulational instabilities. Such instabilities are known as the main obstacles in achieving monochromatic beams. [4pt] [1] B. Eliasson, C. Lui, et al. New Jour. Phys., 11, 2009.[0pt] [2] F. Pegoraro, S.V. Bulanov. Laser Phys., v19, N 2, 2009.

  8. Experimental high gradient testing of a 17.1 GHz photonic band-gap accelerator structure

    DOE PAGES

    Munroe, Brian J.; Zhang, JieXi; Xu, Haoran; ...

    2016-03-29

    In this paper, we report the design, fabrication, and high gradient testing of a 17.1 GHz photonic band-gap (PBG) accelerator structure. Photonic band-gap (PBG) structures are promising candidates for electron accelerators capable of high-gradient operation because they have the inherent damping of high order modes required to avoid beam breakup instabilities. The 17.1 GHz PBG structure tested was a single cell structure composed of a triangular array of round copper rods of radius 1.45 mm spaced by 8.05 mm. The test assembly consisted of the test PBG cell located between conventional (pillbox) input and output cells, with input power ofmore » up to 4 MW from a klystron supplied via a TM01 mode launcher. Breakdown at high gradient was observed by diagnostics including reflected power, downstream and upstream current monitors and visible light emission. The testing procedure was first benchmarked with a conventional disc-loaded waveguide structure, which reached a gradient of 87 MV=m at a breakdown probability of 1.19 × 10–1 per pulse per meter. The PBG structure was tested with 100 ns pulses at gradient levels of less than 90 MV=m in order to limit the surface temperature rise to 120 K. The PBG structure reached up to 89 MV=m at a breakdown probability of 1.09 × 10–1 per pulse per meter. These test results show that a PBG structure can simultaneously operate at high gradients and low breakdown probability, while also providing wakefield damping.« less

  9. Linear Accelerators

    NASA Astrophysics Data System (ADS)

    Sidorin, Anatoly

    2010-01-01

    In linear accelerators the particles are accelerated by either electrostatic fields or oscillating Radio Frequency (RF) fields. Accordingly the linear accelerators are divided in three large groups: electrostatic, induction and RF accelerators. Overview of the different types of accelerators is given. Stability of longitudinal and transverse motion in the RF linear accelerators is briefly discussed. The methods of beam focusing in linacs are described.

  10. Linear Accelerators

    SciTech Connect

    Sidorin, Anatoly

    2010-01-05

    In linear accelerators the particles are accelerated by either electrostatic fields or oscillating Radio Frequency (RF) fields. Accordingly the linear accelerators are divided in three large groups: electrostatic, induction and RF accelerators. Overview of the different types of accelerators is given. Stability of longitudinal and transverse motion in the RF linear accelerators is briefly discussed. The methods of beam focusing in linacs are described.

  11. Signature of recent ice flow acceleration in the radar attenuation and temperature structure of Thwaites Glacier, West Antarctica

    NASA Astrophysics Data System (ADS)

    Schroeder, Dustin; Seroussi, Helene; Chu, Winnie; Young, Duncan

    2016-04-01

    Englacial temperature structure exerts significant control on the rheology and flow of glaciers and ice sheets. It is however logistically prohibitive to directly measure at the glacier-catchment scale. As a result, numerical ice sheet models often make broad assumptions about englacial temperatures based on contemporary ice surface velocities. However, this assumption might break down in regions - like the Amundsen Sea Embayment - that have experienced recent acceleration since temperature and rheology do not respond instantaneously to changes in ice flow regime. To address this challenge, we present a new technique for estimating englacial attenuation rates using bed echoes from radar sounding data. We apply this technique to an airborne survey of Thwaites Glacier and compare the results to temperature and attenuation structures modeled using the numerical Ice Sheet System Model (ISSM) for three surface velocity scenarios. These include contemporary surface velocities, surface velocities from the early 1970s, and ice-sheet balance velocities. We find that the observed attenuation structure is much closer to those modeled with pre-acceleration surface velocities. This suggests that ice sheet models initialized with contemporary surface velocities are likely overestimating the temperature and underestimating the rheology of the fast-flowing trunk and grounding zone of Thwaites Glacier.

  12. Submillimeter-Resolution Radiography of Shielded Structures with Laser-Accelerated Electron Beams

    SciTech Connect

    Ramanathan, Vidya; Banerjee, Sudeep; Powell, Nathan; Cummingham, N. J.; Chandler-Smith, Nate; Zhao, Kun; Brown, Kevin; Umstadter, Donald; Clarke, Shaun; Pozzi, Sara; Beene, James R; Vane, C Randy; Schultz, David Robert

    2010-10-01

    We investigate the use of energetic electron beams for high-resolution radiography of flaws embedded in thick solid objects. A bright, monoenergetic electron beam (with energy >100 MeV) was generated by the process of laser-wakefield acceleration through the interaction of 50-TW, 30-fs laser pulses with a supersonic helium jet. The high energy, low divergence, and small source size of these beams make them ideal for high-resolution radiographic studies of cracks or voids embedded in dense materials that are placed at a large distance from the source. We report radiographic imaging of steel with submillimeter resolution.

  13. Production of Multi-Terawatt Time-Structured CO{sub 2} Laser Pulses for Ion Acceleration

    SciTech Connect

    Haberberger, Dan; Tochitsky, Sergei; Gong Chao; Joshi, Chan

    2010-11-04

    The UCLA Neptune Laboratory CO{sub 2} laser system has been recently upgraded to produce 3ps multi-terawatt 10{mu}m laser pulses. The laser energy is distributed over several 3 ps pulses separated by 18 ps. These temporally structured pulses are applied for laser driven ion acceleration in an H{sub 2} gas jet at a measured plasma density of 2x10{sup 19} cm{sup -3}. Protons in excess of 20 MeV have been observed in the forward direction and with energy spreads ({Delta}E/E{approx}10%).

  14. Particle acceleration

    NASA Technical Reports Server (NTRS)

    Vlahos, L.; Machado, M. E.; Ramaty, R.; Murphy, R. J.; Alissandrakis, C.; Bai, T.; Batchelor, D.; Benz, A. O.; Chupp, E.; Ellison, D.

    1986-01-01

    Data is compiled from Solar Maximum Mission and Hinothori satellites, particle detectors in several satellites, ground based instruments, and balloon flights in order to answer fundamental questions relating to: (1) the requirements for the coronal magnetic field structure in the vicinity of the energization source; (2) the height (above the photosphere) of the energization source; (3) the time of energization; (4) transistion between coronal heating and flares; (5) evidence for purely thermal, purely nonthermal and hybrid type flares; (6) the time characteristics of the energization source; (7) whether every flare accelerates protons; (8) the location of the interaction site of the ions and relativistic electrons; (9) the energy spectra for ions and relativistic electrons; (10) the relationship between particles at the Sun and interplanetary space; (11) evidence for more than one acceleration mechanism; (12) whether there is single mechanism that will accelerate particles to all energies and also heat the plasma; and (13) how fast the existing mechanisms accelerate electrons up to several MeV and ions to 1 GeV.

  15. Polynomial chaos expansion in structural dynamics: Accelerating the convergence of the first two statistical moment sequences

    NASA Astrophysics Data System (ADS)

    Jacquelin, E.; Adhikari, S.; Sinou, J.-J.; Friswell, M. I.

    2015-11-01

    Polynomial chaos solution for the frequency response of linear non-proportionally damped dynamic systems has been considered. It has been observed that for lightly damped systems the convergence of the solution can be very poor in the vicinity of the deterministic resonance frequencies. To address this, Aitken's transformation and its generalizations are suggested. The proposed approach is successfully applied to the sequences defined by the first two moments of the responses, and this process significantly accelerates the polynomial chaos convergence. In particular, a 2-dof system with respectively 1 and 2 parameter uncertainties has been studied. The first two moments of the frequency response were calculated by Monte Carlo simulation, polynomial chaos expansion and Aitken's transformation of the polynomial chaos expansion. Whereas 200 polynomials are required to have a good agreement with Monte Carlo results around the deterministic eigenfrequencies, less than 50 polynomials transformed by the Aitken's method are enough. This latter result is improved if a generalization of Aitken's method (recursive Aitken's transformation, Shank's transformation) is applied. With the proposed convergence acceleration, polynomial chaos may be reconsidered as an efficient method to estimate the first two moments of a random dynamic response.

  16. Design and optimization of Compact Linear Collider main linac accelerating structure

    NASA Astrophysics Data System (ADS)

    Zha, Hao; Grudiev, Alexej

    2016-11-01

    The Compact Linear Collider (CLIC) main linac uses waveguide damped structure as its baseline design. The current baseline structure design written in the CLIC Conceptual Design Report is named "CLIC-G." Recent activities on the CLIC-G design including high power tests on structure prototypes and the study of machining cost assessment had raised the need of reoptimizing the structure design to minimize the machining cost and the pulse surface temperature rise. This work presents optimization of the structure geometry, high-order-mode (HOM) damping loads and the design of a HOM-free power splitter for the input coupler. Compared to the current baseline design CLIC-G, the new structure design reduced the pulse surface temperature rise, input power and manufacturing cost and achieves better suppression to the long range transverse wakefield. Cell disks and damping loads for the new structure design are also more compact than those of the CLIC-G design.

  17. An investigation into the acceleration response of a damaged beam-type structure to a moving force

    NASA Astrophysics Data System (ADS)

    González, A.; Hester, D.

    2013-06-01

    In recent years there have been a growing number of publications on procedures for damage detection in beams from analysing their dynamic response to the passage of a moving force. Most of this research demonstrates their effectiveness by showing that a singularity that did not appear in the healthy structure is present in the response of the damaged structure. This paper elucidates from first principles how the acceleration response can be assumed to consist of 'static' and 'dynamic' components, and where the beam has experienced a localised loss in stiffness, an additional 'damage' component. The combination of these components establishes how the damage singularity will appear in the total response. For a given damage severity, the amplitude of the 'damage' component will depend on how close the damage location is to the sensor, and its frequency content will increase with higher velocities of the moving force. The latter has implications for damage detection because if the frequency content of the 'damage' component includes bridge and/or vehicle frequencies, it becomes more difficult to identify damage. The paper illustrates how a thorough understanding of the relationship between the 'static' and 'damage' components contributes to establish if damage has occurred and to provide an estimation of its location and severity. The findings are corroborated using accelerations from a planar finite element simulation model where the effects of force velocity and bridge span are examined.

  18. Measurement of magnetic-field structures in a laser-wakefield accelerator.

    PubMed

    Kaluza, M C; Schlenvoigt, H-P; Mangles, S P D; Thomas, A G R; Dangor, A E; Schwoerer, H; Mori, W B; Najmudin, Z; Krushelnick, K M

    2010-09-10

    Experimental measurements of magnetic fields generated in the cavity of a self-injecting laser-wakefield accelerator are presented. Faraday rotation is used to determine the existence of multimegagauss fields, constrained to a transverse dimension comparable to the plasma wavelength ∼λp and several λp longitudinally. The fields are generated rapidly and move with the driving laser. In our experiment, the appearance of the magnetic fields is correlated with the production of relativistic electrons, indicating that they are inherently tied to the growth and wave breaking of the nonlinear plasma wave. This evolution is confirmed by numerical simulations, showing that these measurements provide insight into the wakefield evolution with high spatial and temporal resolution.

  19. Accelerated Testing Methodology in Constant Stress-Rate Testing for Advanced Structural Ceramics: A Preloading Technique

    NASA Technical Reports Server (NTRS)

    Choi, Sung R.; Gyekenyesi, John P.; Huebert, Dean; Bartlett, Allen; Choi, Han-Ho

    2001-01-01

    Preloading technique was used as a means of an accelerated testing methodology in constant stress-rate ('dynamic fatigue') testing for two different brittle materials. The theory developed previously for fatigue strength as a function of preload was further verified through extensive constant stress-rate testing for glass-ceramic and CRT glass in room temperature distilled water. The preloading technique was also used in this study to identify the prevailing failure mechanisms at elevated temperatures, particularly at lower test rate in which a series of mechanisms would be associated simultaneously with material failure, resulting in significant strength increase or decrease. Two different advanced ceramics including SiC whisker-reinforced composite silicon nitride and 96 wt% alumina were used at elevated temperatures. It was found that the preloading technique can be used as an additional tool to pinpoint the dominant failure mechanism that is associated with such a phenomenon of considerable strength increase or decrease.

  20. Accelerated Testing Methodology in Constant Stress-Rate Testing for Advanced Structural Ceramics: A Preloading Technique

    NASA Technical Reports Server (NTRS)

    Choi, Sung R.; Gyekenyesi, John P.; Huebert, Dean; Bartlett, Allen; Choi, Han-Ho

    2001-01-01

    Preloading technique was used as a means of an accelerated testing methodology in constant stress-rate ('dynamic fatigue') testing for two different brittle materials. The theory developed previously for fatigue strength as a function of preload was further verified through extensive constant stress-rate testing for glass-ceramic and CRT glass in room temperature distilled water. The preloading technique was also used in this study to identify the prevailing failure mechanisms at elevated temperatures, particularly at lower test rate in which a series of mechanisms would be associated simultaneously with material failure, resulting in significant strength increase or decrease. Two different advanced ceramics including SiC whisker-reinforced composite silicon nitride and 96 wt% alumina were used at elevated temperatures. It was found that the preloading technique can be used as an additional tool to pinpoint the dominant failure mechanism that is associated with such a phenomenon of considerable strength increase or decrease.

  1. Accelerated Testing Methodology in Constant Stress-Rate Testing for Advanced Structural Ceramics: A Preloading Technique

    NASA Technical Reports Server (NTRS)

    Choi, Sung R.; Gyekenyesi, John P.; Huebert, Dean; Bartlett, Allen; Choi, Han-Ho

    2001-01-01

    Preloading technique was used as a means of an accelerated testing methodology in constant stress-rate (dynamic fatigue) testing for two different brittle materials. The theory developed previously for fatigue strength as a function of preload was further verified through extensive constant stress-rate testing for glass-ceramic and CRT glass in room temperature distilled water. The preloading technique was also used in this study to identify the prevailing failure mechanisms at elevated temperatures, particularly at lower test rates in which a series of mechanisms would be associated simultaneously with material failure, resulting in significant strength increase or decrease. Two different advanced ceramics including SiC whisker-reinforced composite silicon nitride and 96 wt% alumina were used at elevated temperatures. It was found that the preloading technique can be used as an additional tool to pinpoint the dominant failure mechanism that is associated with such a phenomenon of considerable strength increase or decrease.

  2. Transformation of the ordered internal structures during the acceleration of fast charged particles in a dense plasma focus

    NASA Astrophysics Data System (ADS)

    Kubes, P.; Paduch, M.; Cikhardt, J.; Cikhardtova, B.; Klir, D.; Kravarik, J.; Rezac, K.; Zielinska, E.; Sadowski, M. J.; Szymaszek, A.; Tomaszewski, K.; Zaloga, D.

    2017-07-01

    The paper concerns important differences in the evolution of plasma column structures during the production of fusion neutrons in the first and subsequent neutron pulses, as observed for plasma-focus discharges performed with the deuterium filling. The first neutron pulse, of a more isotropic distribution, is usually produced during the formation of the first big plasmoid. The next neutron pulses can be generated by the fast deuterons moving dominantly in the downstream direction, at the instants of a disruption of the pinch constriction, when other plasmoids are formed during the constriction evolution. In both cases, the fusion neutrons are produced by a beam-target mechanism, and the acceleration of fast electron- and deuteron-beams can be interpreted by transformation and decay of the magnetic field associated with a filamentary structure of the current flow in the plasmoid.

  3. Accelerated Exploration of Multi-principal Element Alloys for Structural Applications (Postprint)

    DTIC Science & Technology

    2015-04-27

    Compositions and some properties of 5 and 6 component equiatomic alloys that are single phase FCC structures at Tm, are given in Tables 9 and 10, respectively...About 81% of these alloys are BCC, 17% are HCP and only 2% are FCC structures . Additionally applying the modulus restric tion (E4100 GPa) reduces the...calculations, are single-phase FCC structures at Tm. The database used for calculations, FAB values and some calculated properties are also shown. Alloy

  4. Accelerating large-scale protein structure alignments with graphics processing units.

    PubMed

    Pang, Bin; Zhao, Nan; Becchi, Michela; Korkin, Dmitry; Shyu, Chi-Ren

    2012-02-22

    Large-scale protein structure alignment, an indispensable tool to structural bioinformatics, poses a tremendous challenge on computational resources. To ensure structure alignment accuracy and efficiency, efforts have been made to parallelize traditional alignment algorithms in grid environments. However, these solutions are costly and of limited accessibility. Others trade alignment quality for speedup by using high-level characteristics of structure fragments for structure comparisons. We present ppsAlign, a parallel protein structure Alignment framework designed and optimized to exploit the parallelism of Graphics Processing Units (GPUs). As a general-purpose GPU platform, ppsAlign could take many concurrent methods, such as TM-align and Fr-TM-align, into the parallelized algorithm design. We evaluated ppsAlign on an NVIDIA Tesla C2050 GPU card, and compared it with existing software solutions running on an AMD dual-core CPU. We observed a 36-fold speedup over TM-align, a 65-fold speedup over Fr-TM-align, and a 40-fold speedup over MAMMOTH. ppsAlign is a high-performance protein structure alignment tool designed to tackle the computational complexity issues from protein structural data. The solution presented in this paper allows large-scale structure comparisons to be performed using massive parallel computing power of GPU.

  5. Accelerating large-scale protein structure alignments with graphics processing units

    PubMed Central

    2012-01-01

    Background Large-scale protein structure alignment, an indispensable tool to structural bioinformatics, poses a tremendous challenge on computational resources. To ensure structure alignment accuracy and efficiency, efforts have been made to parallelize traditional alignment algorithms in grid environments. However, these solutions are costly and of limited accessibility. Others trade alignment quality for speedup by using high-level characteristics of structure fragments for structure comparisons. Findings We present ppsAlign, a parallel protein structure Alignment framework designed and optimized to exploit the parallelism of Graphics Processing Units (GPUs). As a general-purpose GPU platform, ppsAlign could take many concurrent methods, such as TM-align and Fr-TM-align, into the parallelized algorithm design. We evaluated ppsAlign on an NVIDIA Tesla C2050 GPU card, and compared it with existing software solutions running on an AMD dual-core CPU. We observed a 36-fold speedup over TM-align, a 65-fold speedup over Fr-TM-align, and a 40-fold speedup over MAMMOTH. Conclusions ppsAlign is a high-performance protein structure alignment tool designed to tackle the computational complexity issues from protein structural data. The solution presented in this paper allows large-scale structure comparisons to be performed using massive parallel computing power of GPU. PMID:22357132

  6. Can Accelerators Accelerate Learning?

    NASA Astrophysics Data System (ADS)

    Santos, A. C. F.; Fonseca, P.; Coelho, L. F. S.

    2009-03-01

    The 'Young Talented' education program developed by the Brazilian State Funding Agency (FAPERJ) [1] makes it possible for high-schools students from public high schools to perform activities in scientific laboratories. In the Atomic and Molecular Physics Laboratory at Federal University of Rio de Janeiro (UFRJ), the students are confronted with modern research tools like the 1.7 MV ion accelerator. Being a user-friendly machine, the accelerator is easily manageable by the students, who can perform simple hands-on activities, stimulating interest in physics, and getting the students close to modern laboratory techniques.

  7. Can Accelerators Accelerate Learning?

    SciTech Connect

    Santos, A. C. F.; Fonseca, P.; Coelho, L. F. S.

    2009-03-10

    The 'Young Talented' education program developed by the Brazilian State Funding Agency (FAPERJ)[1] makes it possible for high-schools students from public high schools to perform activities in scientific laboratories. In the Atomic and Molecular Physics Laboratory at Federal University of Rio de Janeiro (UFRJ), the students are confronted with modern research tools like the 1.7 MV ion accelerator. Being a user-friendly machine, the accelerator is easily manageable by the students, who can perform simple hands-on activities, stimulating interest in physics, and getting the students close to modern laboratory techniques.

  8. PARTICLE ACCELERATOR

    DOEpatents

    Teng, L.C.

    1960-01-19

    ABS>A combination of two accelerators, a cyclotron and a ring-shaped accelerator which has a portion disposed tangentially to the cyclotron, is described. Means are provided to transfer particles from the cyclotron to the ring accelerator including a magnetic deflector within the cyclotron, a magnetic shield between the ring accelerator and the cyclotron, and a magnetic inflector within the ring accelerator.

  9. Electron acceleration at localized wave structures in the solar corona (German Title: Elektronenbeschleunigung an lokalen Wellenstrukturen in der Sonnenkorona)

    NASA Astrophysics Data System (ADS)

    Miteva, Rositsa Stoycheva

    2007-07-01

    Our dynamic Sun manifests its activity by different phenomena: from the 11-year cyclic sunspot pattern to the unpredictable and violent explosions in the case of solar flares. During flares, a huge amount of the stored magnetic energy is suddenly released and a substantial part of this energy is carried by the energetic electrons, considered to be the source of the nonthermal radio and X-ray radiation. One of the most important and still open question in solar physics is how the electrons are accelerated up to high energies within (the observed in the radio emission) short time scales. Because the acceleration site is extremely small in spatial extent as well (compared to the solar radius), the electron acceleration is regarded as a local process. The search for localized wave structures in the solar corona that are able to accelerate electrons together with the theoretical and numerical description of the conditions and requirements for this process, is the aim of the dissertation. Two models of electron acceleration in the solar corona are proposed in the dissertation: I. Electron acceleration due to the solar jet interaction with the background coronal plasma (the jet--plasma interaction) A jet is formed when the newly reconnected and highly curved magnetic field lines are relaxed by shooting plasma away from the reconnection site. Such jets, as observed in soft X-rays with the Yohkoh satellite, are spatially and temporally associated with beams of nonthermal electrons (in terms of the so-called type III metric radio bursts) propagating through the corona. A model that attempts to give an explanation for such observational facts is developed here. Initially, the interaction of such jets with the background plasma leads to an (ion-acoustic) instability associated with growing of electrostatic fluctuations in time for certain range of the jet initial velocity. During this process, any test electron that happen to feel this electrostatic wave field is drawn to co

  10. BEAM LOADING AND HIGHER-BAND LONGITUDINAL WAKES IN HIGH PHASE ADVANCE TRAVELING WAVE ACCELERATOR STRUCTURES FOR THE GLC/NLC

    SciTech Connect

    Jones, R

    2004-07-30

    A multi-bunch beam, traversing travelling wave accelerator structures, each with a 5{pi}/6 phase advance per cell, is accelerated at a frequency that is synchronous with the fundamental mode frequency. As per design, the main interaction occurs at the working frequency of 11.424 GHz. However, modes with frequencies surrounding the dominant accelerating mode are also excited and these give rise to additional modal components to the wakefield. Here, we consider the additional modes in the context of X-band accelerator structures for the GLC/NLC (Global Linear Collider/Next Linear Collider). Finite element simulations and field mode-matching models are employed in order to calculate the wakefield.

  11. The structural alteration of gut microbiota in low-birth-weight mice undergoing accelerated postnatal growth

    PubMed Central

    Wang, Jingjing; Tang, Huang; Wang, Xiaoxin; Zhang, Xu; Zhang, Chenhong; Zhang, Menghui; Zhao, Yufeng; Zhao, Liping; Shen, Jian

    2016-01-01

    The transient disruption of gut microbiota in infancy by antibiotics causes adult adiposity in mice. Accelerated postnatal growth (A) leads to a higher risk of adult metabolic syndrome in low birth-weight (LB) humans than in normal birth-weight (NB) individuals, but the underlying mechanism remains unclear. Here, we set up an experiment using LB + A mice, NB + A mice, and control mice with NB and normal postnatal growth. At 24 weeks of age (adulthood), while NB + A animals had a normal body fat content and glucose tolerance compared with controls, LB + A mice exhibited excessive adiposity and glucose intolerance. In infancy, more fecal bacteria implicated in obesity were increased in LB + A pups than in NB + A pups, including Desulfovibrionaceae, Enterorhabdus, and Barnesiella. One bacterium from the Lactobacillus genus, which has been implicated in prevention of adult adiposity, was enhanced only in NB + A pups. Besides, LB + A pups, but not NB + A pups, showed disrupted gut microbiota fermentation activity. After weaning, the fecal microbiota composition of LB + A mice, but not that of NB + A animals, became similar to that of controls by 24 weeks. In infancy, LB + A mice have a more dysbiotic gut microbiome compared to NB + A mice, which might increase their risk of adult metabolic syndrome. PMID:27277748

  12. Atomic oxygen ground-based accelerated tests of spacecraft materials and structures for long-term LEO missions

    NASA Astrophysics Data System (ADS)

    Chernik, Vladimir; Novikov, Lev; Smirnova, Tatyana; Shumov, Andrey

    Spacecraft materials are degradated during long-term low earth orbit (LEO) flight. The Internation Space Station (ISS) is planed to be prolonged the term of action up to 20-25 years. To specify so long life one requires a validation of spacecraft material behaviour conservation for the period. The LEO environment includes atomic oxygen (AO) destructive incident flow. The appropriate AO fluence is proposed to be as high as 10E22-10E23 atom O/sq cm. The simulative ground-based test is evident to be acceptable if its duration is not too long usually under several hundreds of hours. In that case the rate of the test acceleration exceeds 100-200. One way to accelerate test is to increase oxygen particles energy. We test materials under oxygen plasma beam, formed by a magnetoplasmadynamic accelerator, with the oxygen particle energy of 20 -30 eV. In this way we determine an AO effective fluence by a kapton equivalent technique. The beam varies from LEO incident flow by energy, flux and rates of the oxygen dissociation / ionization/ excitation. To evaluate the test adequacy we measured and compared with LEO data erosion yields of a number of polymer materials, applied on spacecraft external surfaces. There were: polyimide (kapton), polyamide (nylon), polyethylene, polyvinyl fluoride (tedlar), polysteren, polymethyl methacrylate, epoxy, polyethylene terephthalate (mylar), graphite. Their relative erosion yields, measured and normalized by polyimide in this way, practically coincide with the data of flight experiments on the ISS. The results ground to use our plasma mode for accelerated tests of spacecraft material durability for long-term LEO flights. We tested quite a number of polymer-based materials and structures usable on ISS and another LEO spacecrafts. The effective AO fluencies ran up to 3,5 10E22 atom O/sq cm corresponding to the ISS flight duration about 20 years. We studied material behaviors like mass and thickness losses, erosion yield, surface morphology

  13. Is structured observation a valid technique to measure handwashing behavior? Use of acceleration sensors embedded in soap to assess reactivity to structured observation.

    PubMed

    Ram, Pavani K; Halder, Amal K; Granger, Stewart P; Jones, Therese; Hall, Peter; Hitchcock, David; Wright, Richard; Nygren, Benjamin; Islam, M Sirajul; Molyneaux, John W; Luby, Stephen P

    2010-11-01

    Structured observation is often used to evaluate handwashing behavior. We assessed reactivity to structured observation in rural Bangladesh by distributing soap containing acceleration sensors and performing structured observation 4 days later. Sensors recorded the number of times soap was moved. In 45 participating households, the median number of sensor soap movements during the 5-hour time block on pre-observation days was 3.7 (range 0.3-10.6). During the structured observation, the median number of sensor soap movements was 5.0 (range 0-18.0), a 35% increase, P = 0.0004. Compared with the same 5-hour time block on pre-observation days, the number of sensor soap movements increased during structured observation by ≥ 20% in 62% of households, and by ≥ 100% in 22% of households. The increase in sensor soap movements during structured observation, compared with pre-observation days, indicates substantial reactivity to the presence of the observer. These findings call into question the validity of structured observation for measurement of handwashing behavior.

  14. Is Structured Observation a Valid Technique to Measure Handwashing Behavior? Use of Acceleration Sensors Embedded in Soap to Assess Reactivity to Structured Observation

    PubMed Central

    Ram, Pavani K.; Halder, Amal K.; Granger, Stewart P.; Jones, Therese; Hall, Peter; Hitchcock, David; Wright, Richard; Nygren, Benjamin; Islam, M. Sirajul; Molyneaux, John W.; Luby, Stephen P.

    2010-01-01

    Structured observation is often used to evaluate handwashing behavior. We assessed reactivity to structured observation in rural Bangladesh by distributing soap containing acceleration sensors and performing structured observation 4 days later. Sensors recorded the number of times soap was moved. In 45 participating households, the median number of sensor soap movements during the 5-hour time block on pre-observation days was 3.7 (range 0.3–10.6). During the structured observation, the median number of sensor soap movements was 5.0 (range 0–18.0), a 35% increase, P = 0.0004. Compared with the same 5-hour time block on pre-observation days, the number of sensor soap movements increased during structured observation by ≥ 20% in 62% of households, and by ≥ 100% in 22% of households. The increase in sensor soap movements during structured observation, compared with pre-observation days, indicates substantial reactivity to the presence of the observer. These findings call into question the validity of structured observation for measurement of handwashing behavior. PMID:21036840

  15. Frequency-Domain Streak Camera and Tomography for Ultrafast Imaging of Evolving and Channeled Plasma Accelerator Structures

    NASA Astrophysics Data System (ADS)

    Li, Zhengyan; Zgadzaj, Rafal; Wang, Xiaoming; Reed, Stephen; Dong, Peng; Downer, Michael C.

    2010-11-01

    We demonstrate a prototype Frequency Domain Streak Camera (FDSC) that can capture the picosecond time evolution of the plasma accelerator structure in a single shot. In our prototype Frequency-Domain Streak Camera, a probe pulse propagates obliquely to a sub-picosecond pump pulse that creates an evolving nonlinear index "bubble" in fused silica glass, supplementing a conventional Frequency Domain Holographic (FDH) probe-reference pair that co-propagates with the "bubble". Frequency Domain Tomography (FDT) generalizes Frequency-Domain Streak Camera by probing the "bubble" from multiple angles and reconstructing its morphology and evolution using algorithms similar to those used in medical CAT scans. Multiplexing methods (Temporal Multiplexing and Angular Multiplexing) improve data storage and processing capability, demonstrating a compact Frequency Domain Tomography system with a single spectrometer.

  16. Radiography with cosmic-ray and compact accelerator muons; Exploring inner-structure of large-scale objects and landforms

    PubMed Central

    NAGAMINE, Kanetada

    2016-01-01

    Cosmic-ray muons (CRM) arriving from the sky on the surface of the earth are now known to be used as radiography purposes to explore the inner-structure of large-scale objects and landforms, ranging in thickness from meter to kilometers scale, such as volcanic mountains, blast furnaces, nuclear reactors etc. At the same time, by using muons produced by compact accelerators (CAM), advanced radiography can be realized for objects with a thickness in the sub-millimeter to meter range, with additional exploration capability such as element identification and bio-chemical analysis. In the present report, principles, methods and specific research examples of CRM transmission radiography are summarized after which, principles, methods and perspective views of the future CAM radiography are described. PMID:27725469

  17. Radiography with cosmic-ray and compact accelerator muons; Exploring inner-structure of large-scale objects and landforms.

    PubMed

    Nagamine, Kanetada

    2016-01-01

    Cosmic-ray muons (CRM) arriving from the sky on the surface of the earth are now known to be used as radiography purposes to explore the inner-structure of large-scale objects and landforms, ranging in thickness from meter to kilometers scale, such as volcanic mountains, blast furnaces, nuclear reactors etc. At the same time, by using muons produced by compact accelerators (CAM), advanced radiography can be realized for objects with a thickness in the sub-millimeter to meter range, with additional exploration capability such as element identification and bio-chemical analysis. In the present report, principles, methods and specific research examples of CRM transmission radiography are summarized after which, principles, methods and perspective views of the future CAM radiography are described.

  18. Magnetospheric Multiscale Satellite Observations of Parallel Electron Acceleration in Magnetic Field Reconnection by Fermi Reflection from Time Domain Structures

    NASA Astrophysics Data System (ADS)

    Mozer, F. S.; Agapitov, O. A.; Artemyev, A.; Burch, J. L.; Ergun, R. E.; Giles, B. L.; Mourenas, D.; Torbert, R. B.; Phan, T. D.; Vasko, I.

    2016-04-01

    The same time domain structures (TDS) have been observed on two Magnetospheric Multiscale Satellites near Earth's dayside magnetopause. These TDS, traveling away from the X line along the magnetic field at 4000 km /s , accelerated field-aligned ˜5 eV electrons to ˜200 eV by a single Fermi reflection of the electrons by these overtaking barriers. Additionally, the TDS contained both positive and negative potentials, so they were a mixture of electron holes and double layers. They evolve in ˜10 km of space or 7 ms of time and their spatial scale size is 10-20 km, which is much larger than the electron gyroradius (<1 km ) or the electron inertial length (4 km at the observation point, less nearer the X line).

  19. Frequency-Domain Streak Camera and Tomography for Ultrafast Imaging of Evolving and Channeled Plasma Accelerator Structures

    SciTech Connect

    Li Zhengyan; Zgadzaj, Rafal; Wang Xiaoming; Reed, Stephen; Dong Peng; Downer, Michael C.

    2010-11-04

    We demonstrate a prototype Frequency Domain Streak Camera (FDSC) that can capture the picosecond time evolution of the plasma accelerator structure in a single shot. In our prototype Frequency-Domain Streak Camera, a probe pulse propagates obliquely to a sub-picosecond pump pulse that creates an evolving nonlinear index 'bubble' in fused silica glass, supplementing a conventional Frequency Domain Holographic (FDH) probe-reference pair that co-propagates with the 'bubble'. Frequency Domain Tomography (FDT) generalizes Frequency-Domain Streak Camera by probing the 'bubble' from multiple angles and reconstructing its morphology and evolution using algorithms similar to those used in medical CAT scans. Multiplexing methods (Temporal Multiplexing and Angular Multiplexing) improve data storage and processing capability, demonstrating a compact Frequency Domain Tomography system with a single spectrometer.

  20. Magnetospheric Multiscale Satellite Observations of Parallel Electron Acceleration in Magnetic Field Reconnection by Fermi Reflection from Time Domain Structures

    NASA Technical Reports Server (NTRS)

    Mozer, F. S.; Agapitov, O. A.; Artemyev, A.; Burch, J. L.; Ergun, R. E.; Giles, B. L.; Mourenas, D.; Torbert, R. B.; Phan, T. D.; Vasko, I.

    2016-01-01

    The same time domain structures (TDS) have been observed on two Magnetospheric Multiscale Satellites near Earth's dayside magnetopause. These TDS, traveling away from the X line along the magnetic field at 4000 km/s, accelerated field-aligned approx. 5 eV electrons to approx. 200 eV by a single Fermi reflection of the electrons by these overtaking barriers. Additionally, the TDS contained both positive and negative potentials, so they were a mixture of electron holes and double layers. They evolve in approx.10 km of space or 7 ms of time and their spatial scale size is 10-20 km, which is much larger than the electron gyroradius (less than1km) or the electron inertial length (4 km at the observation point, less nearer the X line).

  1. High Gradient Accelerator Research

    SciTech Connect

    Temkin, Richard

    2016-07-12

    The goal of the MIT program of research on high gradient acceleration is the development of advanced acceleration concepts that lead to a practical and affordable next generation linear collider at the TeV energy level. Other applications, which are more near-term, include accelerators for materials processing; medicine; defense; mining; security; and inspection. The specific goals of the MIT program are: • Pioneering theoretical research on advanced structures for high gradient acceleration, including photonic structures and metamaterial structures; evaluation of the wakefields in these advanced structures • Experimental research to demonstrate the properties of advanced structures both in low-power microwave cold test and high-power, high-gradient test at megawatt power levels • Experimental research on microwave breakdown at high gradient including studies of breakdown phenomena induced by RF electric fields and RF magnetic fields; development of new diagnostics of the breakdown process • Theoretical research on the physics and engineering features of RF vacuum breakdown • Maintaining and improving the Haimson / MIT 17 GHz accelerator, the highest frequency operational accelerator in the world, a unique facility for accelerator research • Providing the Haimson / MIT 17 GHz accelerator facility as a facility for outside users • Active participation in the US DOE program of High Gradient Collaboration, including joint work with SLAC and with Los Alamos National Laboratory; participation of MIT students in research at the national laboratories • Training the next generation of Ph. D. students in the field of accelerator physics.

  2. Theoretical Investigations of Plasma-Based Accelerators and Other Advanced Accelerator Concepts

    SciTech Connect

    Shuets, G.

    2004-05-21

    Theoretical investigations of plasma-based accelerators and other advanced accelerator concepts. The focus of the work was on the development of plasma based and structure based accelerating concepts, including laser-plasma, plasma channel, and microwave driven plasma accelerators.

  3. Accelerating Early Academic Oral English Development in Transitional Bilingual and Structured English Immersion Programs

    ERIC Educational Resources Information Center

    Tong, Fuhui; Lara-Alecio, Rafael; Irby, Beverly; Mathes, Patricia; Kwok, Oi-man

    2008-01-01

    The authors examined the effectiveness of a 2-year (kindergarten and first grade) oral English intervention provided to 534 Hispanic English-language learners in transitional bilingual education (TBE) and structured English immersion (SEI) programs. Using latent growth modeling, the authors compared instructional programs in relation to growth…

  4. Final Report on "Development and Testing of Advanced Accelerator Structures and Technologies at 11.424 GHz"

    SciTech Connect

    Gold, Steven H.

    2013-10-13

    This is the final report on the research program ?Development and Testing of Advanced Accelerator Structures and Technologies at 11.424 GHz,? which was carried out by the Naval Research Laboratory (NRL) under Interagency Agreement DE?AI02?01ER41170 with the Department of Energy. The period covered by this report is 15 July 2010 ? 14 July 2013. The program included two principal tasks. Task 1 involved a study of the key physics issues related to the use of high gradient dielectric-loaded accelerating (DLA) structures in rf linear accelerators and was carried out in collaboration with Argonne National Laboratory (ANL) and Euclid Techlabs LLC. Task 2 involved a study of high power active microwave pulse compressors and was carried out in collaboration with Omega-P, Inc. and the Institute of Applied Physics of the Russian Academy of Sciences in Nizhny Novgorod. The studies under Task 1 were focused on rf-induced multipactor and breakdown in externally driven DLA structures at the 200-ns timescale. Suppression of multipactor and breakdown are essential to the practical application of dielectric structures in rf linear accelerators. The structures that were studied were developed by ANL and Euclid Techlabs and their performance was evaluated at high power in the X-band Magnicon Laboratory at NRL. Three structures were designed, fabricated, and tested, and the results analyzed in the first two years of the program: a clamped quartz traveling-wave (TW) structure, a externally copper-coated TW structure, and an externally copper-coated dielectric standing-wave (SW) structure. These structures showed that rf breakdown could be largely eliminated by eliminating dielectric joints in the structures, but that the multipactor loading was omnipresent. In the third year of the program, the focus of the program was on multipactor suppression using a strong applied axial magnetic field, as proposed by Chang et al. [C. Chang et al., J. Appl. Phys. 110, 063304 (2011).], and a

  5. Earthworms modify microbial community structure and accelerate maize stover decomposition during vermicomposting.

    PubMed

    Chen, Yuxiang; Zhang, Yufen; Zhang, Quanguo; Xu, Lixin; Li, Ran; Luo, Xiaopei; Zhang, Xin; Tong, Jin

    2015-11-01

    In the present study, maize stover was vermicomposted with the epigeic earthworm Eisenia fetida. The results showed that, during vermicomposting process, the earthworms promoted decomposition of maize stover. Analysis of microbial communities of the vermicompost by high-throughput pyrosequencing showed more complex bacterial community structure in the substrate treated by the earthworms than that in the control group. The dominant microbial genera in the treatment with the earthworms were Pseudoxanthomonas, Pseudomonas, Arthrobacter, Streptomyces, Cryptococcus, Guehomyces, and Mucor. Compared to the control group, the relative abundance of lignocellulose degradation microorganisms increased. The results indicated that the earthworms modified the structure of microbial communities during vermicomposting process, activated the growth of lignocellulose degradation microorganisms, and triggered the lignocellulose decomposition.

  6. Structural dynamics of the monoamine transporter homolog LeuT from accelerated conformational sampling and channel analysis.

    PubMed

    Thomas, James R; Gedeon, Patrick C; Madura, Jeffry D

    2014-10-01

    The bacterial leucine transporter LeuT retains significant secondary structure similarities to the human monoamine transporters (MAT) such as the dopamine and serotonin reuptake proteins. The primary method of computational study of the MATs has been through the use of the crystallized LeuT structure. Different conformations of LeuT can give insight into mechanistic details of the MAT family. A conformational sampling performed through accelerated molecular dynamics simulations testing different combinations of the leucine substrate and bound sodium ions revealed seven distinct conformational clusters. Further analysis has been performed to target salt-bridge residues R30-D404, Y108-F253, and R5-D369 and transmembrane domains on both the seven isolated structures and the total trajectories. In addition, solvent accessibility of LeuT and its substrate binding pockets has been analyzed using a program for calculating channel radii. Occupation of the Na2 site stabilizes the outward conformation and should bind to the open outward conformation before the leucine and Na1 sodium while two possible pathways were found to be available for intracellular transport.

  7. H.V. support structure of 3MVDC generator and its protection from HV discharges in vacuum and SF6 gas for DC electron accelerator

    SciTech Connect

    Sharma, D.K.; Rajan, R.N.; Srivastava, S.K.; Dewangan, S.; Jayaprakash, D.; Bakhtsingh, R.I.; Acharya, S.; Gantayet, L.M.

    2014-07-01

    Accelerator and Pulse Power Division of BARC has developed a DC electron accelerator for cross linking of polymers, medical sterilisation, preservation of food. The demonstration of stack-gas cleanup for green power generation has been demonstrated successfully. The support structure of the 3MVDC voltage generator is made of Perspex for high dielectric strength, easy availability of raw material, excellent radiation resistance and long term dimensional stability. This paper describes the salient design features of the High voltage support structure in brief. (author)

  8. GPU-accelerated computing for Lagrangian coherent structures of multi-body gravitational regimes

    NASA Astrophysics Data System (ADS)

    Lin, Mingpei; Xu, Ming; Fu, Xiaoyu

    2017-04-01

    Based on a well-established theoretical foundation, Lagrangian Coherent Structures (LCSs) have elicited widespread research on the intrinsic structures of dynamical systems in many fields, including the field of astrodynamics. Although the application of LCSs in dynamical problems seems straightforward theoretically, its associated computational cost is prohibitive. We propose a block decomposition algorithm developed on Compute Unified Device Architecture (CUDA) platform for the computation of the LCSs of multi-body gravitational regimes. In order to take advantage of GPU's outstanding computing properties, such as Shared Memory, Constant Memory, and Zero-Copy, the algorithm utilizes a block decomposition strategy to facilitate computation of finite-time Lyapunov exponent (FTLE) fields of arbitrary size and timespan. Simulation results demonstrate that this GPU-based algorithm can satisfy double-precision accuracy requirements and greatly decrease the time needed to calculate final results, increasing speed by approximately 13 times. Additionally, this algorithm can be generalized to various large-scale computing problems, such as particle filters, constellation design, and Monte-Carlo simulation.

  9. Hydrophobin Film Structure for HFBI and HFBII and Mechanism for Accelerated Film Formation

    PubMed Central

    Magarkar, Aniket; Mele, Nawel; Abdel-Rahman, Noha; Butcher, Sarah; Torkkeli, Mika; Serimaa, Ritva; Paananen, Arja; Linder, Markus; Bunker, Alex

    2014-01-01

    Hydrophobins represent an important group of proteins from both a biological and nanotechnological standpoint. They are the means through which filamentous fungi affect their environment to promote growth, and their properties at interfaces have resulted in numerous applications. In our study we have combined protein docking, molecular dynamics simulation, and electron cryo-microscopy to gain atomistic level insight into the surface structure of films composed of two class II hydrophobins: HFBI and HFBII produced by Trichoderma reesei. Together our results suggest a unit cell composed of six proteins; however, our computational results suggest P6 symmetry, while our experimental results show P3 symmetry with a unit cell size of 56 Å. Our computational results indicate the possibility of an alternate ordering with a three protein unit cell with P3 symmetry and a smaller unit cell size, and we have used a Monte Carlo simulation of a spin model representing the hydrophobin film to show how this alternate metastable structure may play a role in increasing the rate of surface coverage by hydrophobin films, possibly indicating a mechanism of more general significance to both biology and nanotechnology. PMID:25079355

  10. Effective seismic acceleration measurements for low-cost Structural Health Monitoring

    NASA Astrophysics Data System (ADS)

    Pentaris, Fragkiskos; Makris, John P.

    2015-04-01

    There is increasing demand on cost effective Structural Health Monitoring systems for buildings as well as important and/or critical constructions. The front end for all these systems is the accelerometer. We present a comparative study of two low cost MEMS accelaration sensors against a very sensitive, high dynamic range strong motion accelerometer of force balance type but much more expensive. A real experiment was realized by deploying the three sesnors in a reinforced concrete building of the premises of TEI of Crete at Chania Crete, an earthquake prone region. The analysis of the collected accelararion data from many seismic events indicates that all sensors are able to efficiently reveal the seismic response of the construction in terms of PSD. Furthermore, it is shown that coherence diagrams between excitation and response of the building under study, depict structural characteristics but also the seismic energy distribution. This work is supported by the Archimedes III Program of the Ministry of Education of Greece, through the Operational Program "Educational and Lifelong Learning", in the framework of the project entitled "Interdisciplinary Multi-Scale Research of Earthquake Physics and Seismotectonics at the front of the Hellenic Arc (IMPACT-ARC)" and is co-financed by the European Union (European Social Fund) and Greek national funds.

  11. Successive range expansion promotes diversity and accelerates evolution in spatially structured microbial populations.

    PubMed

    Goldschmidt, Felix; Regoes, Roland R; Johnson, David R

    2017-09-01

    Successive range expansions occur within all domains of life, where one population expands first (primary expansion) and one or more secondary populations then follow (secondary expansion). In general, genetic drift reduces diversity during range expansion. However, it is not clear whether the same effect applies during successive range expansion, mainly because the secondary population must expand into space occupied by the primary population. Here we used an experimental microbial model system to show that, in contrast to primary range expansion, successive range expansion promotes local population diversity. Because of mechanical constraints imposed by the presence of the primary population, the secondary population forms fractal-like dendritic structures. This divides the advancing secondary population into many small sub-populations and promotes intermixing between the primary and secondary populations. We further developed a mathematical model to simulate the formation of dendritic structures in the secondary population during succession. By introducing mutations in the primary or dendritic secondary populations, we found that mutations are more likely to accumulate in the dendritic secondary populations. Our results thus show that successive range expansion can promote intermixing over the short term and increase genetic diversity over the long term. Our results therefore have potentially important implications for predicting the ecological processes and evolutionary trajectories of microbial communities.

  12. Accelerating Nanoscale Research with Neutron Total Scattering: Linking Structure and Function in Finite Materials

    NASA Astrophysics Data System (ADS)

    Page, Katharine

    2012-10-01

    h -abstract-pard In contrast to bulk materials, nanomaterials and nanoparticles, comprised of a few hundred to tens of thousands of atoms, require every atom's position to be located in order to understand their structure-property relationships. New behavior can arise with a constricted, expanded, or distorted lattice, variation in surface termination structure, ligand capping or stabilization, or with the increasingly diverse set of shapes and architectures appearing in nanoscience literature today: tubes, pyramids, stars, core-shell and matrix-confined particles, multilayer films, etc. Pair distribution function (PDF) analysis, based on spallation neutron or synchrotron x-ray total scattering data, has emerged as a very promising characterization method for nanomaterials in recent years. Total scattering methods provide information about every pair of atoms probed in a diffraction experiment and thus contain an unexploited wealth of information for finite systems. In this contribution we will present our work establishing the influence of particle size and shape on the nature and correlation of local atomic dipoles in finite ferroelectric systems. We also review current data-driven modeling capabilities and outline the need for evolution of robust computational tools to follow other complex nanoscale phenomena with scattering data. pard-/abstract-

  13. Wake fields in 9-cell TESLA accelerating structures : Spectral Element Discontinuous Galerkin (SEDG) simulations.

    SciTech Connect

    Min, M.; Fischer, P. F.; Chae, Y.-C.

    2007-01-01

    Using our recently developed high-order accurate Maxwell solver, NEKCEM, we carried out longitudinal wakefield calculations for a 9-cell TESLA cavity structure in 3D. Indirect method is used for wake potential calculations. Computational results with NEKCEM are compared with those of GdfidL. NEKCEM uses a spectral element discontinuous Galerkin (SEDG) method based on a domain decomposition approach using spectral-element discretizations on Gauss-Lobatto-Legendre grids with body-conforming hexahedral meshes. The numerical scheme is designed to ensure high-order spectral accuracy, using the discontinuous Galerkin form with boundary conditions weakly enforced through a flux term between elements. Concerns related to implementation on wake potential calculations are discussed, and wake potential calculations with indirect method by NEKCEM compared with the results of the finite difference time-domain code GdfidL.

  14. Resistive foil edge grading for accelerator and other high voltage structures

    DOEpatents

    Caporaso, George J.; Sampayan, Stephen F.; Sanders, David M.

    2014-06-10

    In a structure or device having a pair of electrical conductors separated by an insulator across which a voltage is placed, resistive layers are formed around the conductors to force the electric potential within the insulator to distribute more uniformly so as to decrease or eliminate electric field enhancement at the conductor edges. This is done by utilizing the properties of resistive layers to allow the voltage on the electrode to diffuse outwards, reducing the field stress at the conductor edge. Preferably, the resistive layer has a tapered resistivity, with a lower resistivity adjacent to the conductor and a higher resistivity away from the conductor. Generally, a resistive path across the insulator is provided, preferably by providing a resistive region in the bulk of the insulator, with the resistive layer extending over the resistive region.

  15. Accelerated structure-based design of chemically diverse allosteric modulators of a muscarinic G protein-coupled receptor

    PubMed Central

    Miao, Yinglong; Goldfeld, Dahlia Anne; Moo, Ee Von; Sexton, Patrick M.; Christopoulos, Arthur; McCammon, J. Andrew; Valant, Celine

    2016-01-01

    Design of ligands that provide receptor selectivity has emerged as a new paradigm for drug discovery of G protein-coupled receptors, and may, for certain families of receptors, only be achieved via identification of chemically diverse allosteric modulators. Here, the extracellular vestibule of the M2 muscarinic acetylcholine receptor (mAChR) is targeted for structure-based design of allosteric modulators. Accelerated molecular dynamics (aMD) simulations were performed to construct structural ensembles that account for the receptor flexibility. Compounds obtained from the National Cancer Institute (NCI) were docked to the receptor ensembles. Retrospective docking of known ligands showed that combining aMD simulations with Glide induced fit docking (IFD) provided much-improved enrichment factors, compared with the Glide virtual screening workflow. Glide IFD was thus applied in receptor ensemble docking, and 38 top-ranked NCI compounds were selected for experimental testing. In [3H]N-methylscopolamine radioligand dissociation assays, approximately half of the 38 lead compounds altered the radioligand dissociation rate, a hallmark of allosteric behavior. In further competition binding experiments, we identified 12 compounds with affinity of ≤30 μM. With final functional experiments on six selected compounds, we confirmed four of them as new negative allosteric modulators (NAMs) and one as positive allosteric modulator of agonist-mediated response at the M2 mAChR. Two of the NAMs showed subtype selectivity without significant effect at the M1 and M3 mAChRs. This study demonstrates an unprecedented successful structure-based approach to identify chemically diverse and selective GPCR allosteric modulators with outstanding potential for further structure-activity relationship studies. PMID:27601651

  16. Structural insights into how Yrb2p accelerates the assembly of the Xpo1p nuclear export complex.

    PubMed

    Koyama, Masako; Shirai, Natsuki; Matsuura, Yoshiyuki

    2014-11-06

    Proteins and ribonucleoproteins containing a nuclear export signal (NES) assemble with the exportin Xpo1p (yeast CRM1) and Gsp1p-GTP (yeast Ran-GTP) in the nucleus and exit through the nuclear pore complex. In the cytoplasm, Yrb1p (yeast RanBP1) displaces NES from Xpo1p. Efficient export of NES-cargoes requires Yrb2p (yeast RanBP3), a primarily nuclear protein containing nucleoporin-like phenylalanine-glycine (FG) repeats and a low-affinity Gsp1p-binding domain (RanBD). Here, we show that Yrb2p strikingly accelerates the association of Gsp1p-GTP and NES to Xpo1p. We have solved the crystal structure of the Xpo1p-Yrb2p-Gsp1p-GTP complex, a key assembly intermediate that can bind cargo rapidly. Although the NES-binding cleft of Xpo1p is closed in this intermediate, our data suggest that preloading of Gsp1p-GTP onto Xpo1p by Yrb2p, conformational flexibility of Xpo1p, and the low affinity of RanBD enable active displacement of Yrb2p RanBD by NES to occur effectively. The structure also reveals the major binding sites for FG repeats on Xpo1p.

  17. Role of Nottingham and Thomson effects in heating of micro-protrusion in high-gradient accelerating structures

    NASA Astrophysics Data System (ADS)

    Keser, Aydin; Nusinovich, Gregory; Kashyn, Dmytro; Antonsen, Thomas

    2012-10-01

    It is widely accepted that one of the reasons for appearance of the RF breakdown which limits operation of high-gradient accelerating structures is the electron dark current [1]. This field emitted current, usually considered as a precursor of the breakdown, can be emitted from apexes of micro-protrusions on a structure surface. Therefore field and thermal processes in such protrusions deserve careful studies [2, 3]. The goal of our first study [3] was to analyze 2D process of RF field penetration inside protrusion of a metal with finite conductivity and to study corresponding Joule heating. In the current study, it is found that space charges can have a stabilizing effect on the electric field. We include a modification of the 1D model described in [4]. Moreover, we include into consideration, first, the Nottingham effect which may significantly change the protrusion heating. We also investigate the interplay between high temperature gradients and electric fields (Thomson heating).[4pt] [1] Wang and Loew, SLAC PUB 7684 October 1997.[0pt] [2] K.L. Jensen, Y.Y. Lau, D.W. Feldman, P.G. O'Shea, Phys. Rev. ST Accel. Beams 11, 081001(2008).[0pt] [3] Kashyn et al, AAC-2010.[0pt] [4] K.L. Jensen, J. LEbowitz, Y.Y. LAu, J. Luginsland, Journal of Applied Physics 111, 054917(2012).

  18. Diffusion bonding and brazing of high purity copper for linear collider accelerator structures

    NASA Astrophysics Data System (ADS)

    Elmer, J. W.; Klingmann, J.; van Bibber, K.

    2001-05-01

    is proposed for fabricating the NLC structures. The structure would be assembled with pure silver braze inserts using a self-aligning step joint design, then the assembly would be vacuum diffusion bonded at 700 °C and 3.45 MPa pressure to seal the critical inner portion of the assembly. Finally, during the same furnace cycle, the temperature would be increased to 800 °C in order to react the silver with the copper to form a liquid braze alloy that would join and seal the outer portion of the cells together.

  19. Exploration of multi-fold symmetry element-loaded superconducting radio frequency structure for reliable acceleration of low- & medium-beta ion species

    SciTech Connect

    Huang, Shichun; Geng, Rongli

    2015-09-01

    Reliable acceleration of low- to medium-beta proton or heavy ion species is needed for future high-current superconducting radio frequency (SRF) accelerators. Due to the high-Q nature of an SRF resonator, it is sensitive to many factors such as electron loading (from either the accelerated beam or from parasitic field emitted electrons), mechanical vibration, and liquid helium bath pressure fluctuation etc. To increase the stability against those factors, a mechanically strong and stable RF structure is desirable. Guided by this consideration, multi-fold symmetry element-loaded SRF structures (MFSEL), cylindrical tanks with multiple (n>=3) rod-shaped radial elements, are being explored. The top goal of its optimization is to improve mechanical stability. A natural consequence of this structure is a lowered ratio of the peak surface electromagnetic field to the acceleration gradient as compared to the traditional spoke cavity. A disadvantage of this new structure is an increased size for a fixed resonant frequency and optimal beta. This paper describes the optimization of the electro-magnetic (EM) design and preliminary mechanical analysis for such structures.

  20. Accelerated structural decrements in the aging female rhesus macaque lung compared with males

    PubMed Central

    Herring, Matt J.; Avdalovic, Mark V.; Quesenberry, Cheryl L.; Putney, Lei F.; Tyler, Nancy K.; Ventimiglia, Frank F.; St. George, Judith A.

    2013-01-01

    Aging is associated with morphometric changes in the lung that lead to decreased lung function. The nonhuman primate lung has been shown to have similar architectural, morphological, and developmental patterns to that of humans. We hypothesized that the lungs of rhesus monkeys age in a pattern similar to human lungs. Thirty-four rhesus monkeys from the California National Primate Research Center were euthanized, necropsied, and the whole lungs sampled. Stereological analysis was performed to assess the morphological changes associated with age. The number of alveoli declined significantly from age 9 to 33 yr with a greater decline in females compared with males. Lungs of females contained roughly 20% more alveoli at age 9 yr than males, but by ∼30 yr of age, females had 30% fewer alveoli than males. The volume of alveolar air also showed a significant linear decrease in females relative to age, while males did not. The number-weighted mean volume of alveoli showed a significant positive correlation with age in females but not in males. The volume of alveolar duct showed a significant positive correlation with age in females, but not in males. Structural decrements due to aging in the lung were increased in the female compared with male rhesus monkey. PMID:23144321

  1. Accelerating Atomic Orbital-based Electronic Structure Calculation via Pole Expansion plus Selected Inversion

    SciTech Connect

    Lin, Lin; Chen, Mohan; Yang, Chao; He, Lixin

    2012-02-10

    We describe how to apply the recently developed pole expansion plus selected inversion (PEpSI) technique to Kohn-Sham density function theory (DFT) electronic structure calculations that are based on atomic orbital discretization. We give analytic expressions for evaluating charge density, total energy, Helmholtz free energy and atomic forces without using the eigenvalues and eigenvectors of the Kohn-Sham Hamiltonian. We also show how to update the chemical potential without using Kohn-Sham eigenvalues. The advantage of using PEpSI is that it has a much lower computational complexity than that associated with the matrix diagonalization procedure. We demonstrate the performance gain by comparing the timing of PEpSI with that of diagonalization on insulating and metallic nanotubes. For these quasi-1D systems, the complexity of PEpSI is linear with respect to the number of atoms. This linear scaling can be observed in our computational experiments when the number of atoms in a nanotube is larger than a few hundreds. Both the wall clock time and the memory requirement of PEpSI is modest. This makes it even possible to perform Kohn-Sham DFT calculations for 10,000-atom nanotubes on a single processor. We also show that the use of PEpSI does not lead to loss of accuracy required in a practical DFT calculation.

  2. Dark spot growth and its acceleration factor in organic light-emitting diodes with single barrier structure

    NASA Astrophysics Data System (ADS)

    Okada, Takeru; Yoshida, Ayako; Tsuji, Taishi

    2017-06-01

    Using organic light-emitting diodes (OLEDs) without encapsulation, dark spot growth and its acceleration factor at high temperature and high humidity were measured and compared with those of edge shrink at the cathode edge. The water permeation model explained the time evolution of dark spots and edge shrink, and the acceleration factor was the same between dark spots and edge shrink. The acceleration factor of edge shrink was proportional to the relative humidity at a constant temperature and showed Arrhenius temperature dependence.

  3. Biological/Biomedical Accelerator Mass Spectrometry Targets. 2. Physical, Morphological, and Structural Characteristics

    PubMed Central

    2008-01-01

    The number of biological/biomedical applications that require AMS to achieve their goals is increasing, and so is the need for a better understanding of the physical, morphological, and structural traits of high quality of AMS targets. The metrics of quality included color, hardness/texture, and appearance (photo and SEM), along with FT-IR, Raman, and powder X-ray diffraction spectra that correlate positively with reliable and intense ion currents and accuracy, precision, and sensitivity of fraction modern (Fm). Our previous method produced AMS targets of gray-colored iron−carbon materials (ICM) 20% of the time and of graphite-coated iron (GCI) 80% of the time. The ICM was hard, its FT-IR spectra lacked the sp2 bond, its Raman spectra had no detectable G′ band at 2700 cm−1, and it had more iron carbide (Fe3C) crystal than nanocrystalline graphite or graphitizable carbon (g-C). ICM produced low and variable ion current whereas the opposite was true for the graphitic GCI. Our optimized method produced AMS targets of graphite-coated iron powder (GCIP) 100% of the time. The GCIP shared some of the same properties as GCI in that both were black in color, both produced robust ion current consistently, their FT-IR spectra had the sp2 bond, their Raman spectra had matching D, G, G′, D+G, and D′′ bands, and their XRD spectra showed matching crystal size. GCIP was a powder that was easy to tamp into AMS target holders that also facilitated high throughput. We concluded that AMS targets of GCIP were a mix of graphitizable carbon and Fe3C crystal, because none of their spectra, FT-IR, Raman, or XRD, matched exactly those of the graphite standard. Nevertheless, AMS targets of GCIP consistently produced the strong, reliable, and reproducible ion currents for high-throughput AMS analysis (270 targets per skilled analyst/day) along with accurate and precise Fm values. PMID:18785762

  4. Biological/biomedical accelerator mass spectrometry targets. 2. Physical, morphological, and structural characteristics.

    PubMed

    Kim, Seung-Hyun; Kelly, Peter B; Clifford, Andrew J

    2008-10-15

    The number of biological/biomedical applications that require AMS to achieve their goals is increasing, and so is the need for a better understanding of the physical, morphological, and structural traits of high quality of AMS targets. The metrics of quality included color, hardness/texture, and appearance (photo and SEM), along with FT-IR, Raman, and powder X-ray diffraction spectra that correlate positively with reliable and intense ion currents and accuracy, precision, and sensitivity of fraction modern ( F m). Our previous method produced AMS targets of gray-colored iron-carbon materials (ICM) 20% of the time and of graphite-coated iron (GCI) 80% of the time. The ICM was hard, its FT-IR spectra lacked the sp (2) bond, its Raman spectra had no detectable G' band at 2700 cm (-1), and it had more iron carbide (Fe 3C) crystal than nanocrystalline graphite or graphitizable carbon (g-C). ICM produced low and variable ion current whereas the opposite was true for the graphitic GCI. Our optimized method produced AMS targets of graphite-coated iron powder (GCIP) 100% of the time. The GCIP shared some of the same properties as GCI in that both were black in color, both produced robust ion current consistently, their FT-IR spectra had the sp (2) bond, their Raman spectra had matching D, G, G', D +G, and D '' bands, and their XRD spectra showed matching crystal size. GCIP was a powder that was easy to tamp into AMS target holders that also facilitated high throughput. We concluded that AMS targets of GCIP were a mix of graphitizable carbon and Fe 3C crystal, because none of their spectra, FT-IR, Raman, or XRD, matched exactly those of the graphite standard. Nevertheless, AMS targets of GCIP consistently produced the strong, reliable, and reproducible ion currents for high-throughput AMS analysis (270 targets per skilled analyst/day) along with accurate and precise F m values.

  5. Surface analysis of oxygen free electrolytic-copper X-band accelerating structures and possible correlation to radio frequency breakdown events

    NASA Astrophysics Data System (ADS)

    Harvey, S. E.; Le Pimpec, F.; Kirby, R. E.; Marcelja, F.; Adamson, K.; Garwin, E. L.

    2004-07-01

    X-band accelerator structures meeting the next linear collider design requirements have been found to suffer vacuum surface damage caused by rf breakdown, when processed to high electric-field gradients. Improved understanding of these breakdown events is desirable for the development of structure designs, fabrication procedures, and processing techniques that minimize structure damage. rf reflected wave analysis and acoustic sensor pickup have provided breakdowns localization in rf structures. Particle contaminations found following clean autopsy of four rf-processed traveling wave structures have been catalogued and analyzed. Their influence on rf breakdown, as well as that of several other material-based properties, are discussed. .

  6. FFAGS for rapid acceleration

    SciTech Connect

    Carol J. Johnstone and Shane Koscielniak

    2002-09-30

    When large transverse and longitudinal emittances are to be transported through a circular machine, extremely rapid acceleration holds the advantage that the beam becomes immune to nonlinear resonances because there is insufficient time for amplitudes to build up. Uncooled muon beams exhibit large emittances and require fast acceleration to avoid decay losses and would benefit from this style of acceleration. The approach here employs a fixed-field alternating gradient or FFAG magnet structure and a fixed frequency acceleration system. Acceptance is enhanced by the use only of linear lattice elements, and fixed-frequency rf enables the use of cavities with large shunt resistance and quality factor.

  7. Introduction to Microwave Linear [Accelerators

    SciTech Connect

    Whittum, David H

    1999-01-04

    The elements of microwave linear accelerators are introduced starting with the principles of acceleration and accelerating structures. Considerations for microwave structure modeling and design are developed from an elementary point of view. Basic elements of microwave electronics are described for application to the accelerator circuit and instrumentation. Concepts of beam physics are explored together with examples of common beamline instruments. Charged particle optics and lattice diagnostics are introduced. Considerations for fixed-target and colliding-beam experimentation are summarized.

  8. Switched Matrix Accelerator

    SciTech Connect

    Whittum, David H

    2000-10-04

    We describe a new concept for a microwave circuit functioning as a charged-particle accelerator at mm-wavelengths, permitting an accelerating gradient higher than conventional passive circuits can withstand consistent with cyclic fatigue. The device provides acceleration for multiple bunches in parallel channels, and permits a short exposure time for the conducting surface of the accelerating cavities. Our analysis includes scalings based on a smooth transmission line model and a complementary treatment with a coupled-cavity simulation. We provide also an electromagnetic design for the accelerating structure, arriving at rough dimensions for a seven-cell accelerator matched to standard waveguide and suitable for bench tests at low power in air at 91.392. GHz. A critical element in the concept is a fast mm-wave switch suitable for operation at high-power, and we present the considerations for implementation in an H-plane tee. We discuss the use of diamond as the photoconductor switch medium.

  9. STRUCTURAL DESIGN CRITERIA FOR TARGET/BLANKET SYSTEM COMPONENT MATERIALS FOR THE ACCELERATOR PRODUCTION OF TRITIUM PROJECT

    SciTech Connect

    W. JOHNSON; R. RYDER; P. RITTENHOUSE

    2001-01-01

    The design of target/blanket system components for the Accelerator Production of Tritium (APT) plant is dependent on the development of materials properties data specified by the designer. These data are needed to verify that component designs are adequate. The adequacy of the data will be related to safety, performance, and economic considerations, and to other requirements that may be deemed necessary by customers and regulatory bodies. The data required may already be in existence, as in the open technical literature, or may need to be generated, as is often the case for the design of new systems operating under relatively unique conditions. The designers' starting point for design data needs is generally some form of design criteria used in conjunction with a specified set of loading conditions and associated performance requirements. Most criteria are aimed at verifying the structural adequacy of the component, and often take the form of national or international standards such as the ASME Boiler and Pressure Vessel Code (ASME B and PV Code) or the French Nuclear Structural Requirements (RCC-MR). Whether or not there are specific design data needs associated with the use of these design criteria will largely depend on the uniqueness of the conditions of operation of the component. A component designed in accordance with the ASME B and PV Code, where no unusual environmental conditions exist, will utilize well-documented, statistically-evaluated developed in conjunction with the Code, and will not be likely to have any design data needs. On the other hand, a component to be designed to operate under unique APT conditions, is likely to have significant design data needs. Such a component is also likely to require special design criteria for verification of its structural adequacy, specifically accounting for changes in materials properties which may occur during exposure in the service environment. In such a situation it is common for the design criteria and

  10. Stringent restriction from the growth of large-scale structure on apparent acceleration in inhomogeneous cosmological models.

    PubMed

    Ishak, Mustapha; Peel, Austin; Troxel, M A

    2013-12-20

    Probes of cosmic expansion constitute the main basis for arguments to support or refute a possible apparent acceleration due to different expansion rates in the Universe as described by inhomogeneous cosmological models. We present in this Letter a separate argument based on results from an analysis of the growth rate of large-scale structure in the Universe as modeled by the inhomogeneous cosmological models of Szekeres. We use the models with no assumptions of spherical or axial symmetries. We find that while the Szekeres models can fit very well the observed expansion history without a Λ, they fail to produce the observed late-time suppression in the growth unless Λ is added to the dynamics. A simultaneous fit to the supernova and growth factor data shows that the cold dark matter model with a cosmological constant (ΛCDM) provides consistency with the data at a confidence level of 99.65%, while the Szekeres model without Λ achieves only a 60.46% level. When the data sets are considered separately, the Szekeres with no Λ fits the supernova data as well as the ΛCDM does, but provides a very poor fit to the growth data with only 31.31% consistency level compared to 99.99% for the ΛCDM. This absence of late-time growth suppression in inhomogeneous models without a Λ is consolidated by a physical explanation.

  11. Does Grammatical Structure Accelerate Number Word Learning? Evidence from Learners of Dual and Non-Dual Dialects of Slovenian

    PubMed Central

    Plesničar, Vesna; Razboršek, Tina; Sullivan, Jessica; Barner, David

    2016-01-01

    How does linguistic structure affect children’s acquisition of early number word meanings? Previous studies have tested this question by comparing how children learning languages with different grammatical representations of number learn the meanings of labels for small numbers, like 1, 2, and 3. For example, children who acquire a language with singular-plural marking, like English, are faster to learn the word for 1 than children learning a language that lacks the singular-plural distinction, perhaps because the word for 1 is always used in singular contexts, highlighting its meaning. These studies are problematic, however, because reported differences in number word learning may be due to unmeasured cross-cultural differences rather than specific linguistic differences. To address this problem, we investigated number word learning in four groups of children from a single culture who spoke different dialects of the same language that differed chiefly with respect to how they grammatically mark number. We found that learning a dialect which features “dual” morphology (marking of pairs) accelerated children’s acquisition of the number word two relative to learning a “non-dual” dialect of the same language. PMID:27486802

  12. Effects of fuel cetane number on the structure of diesel spray combustion: An accelerated Eulerian stochastic fields method

    NASA Astrophysics Data System (ADS)

    Jangi, Mehdi; Lucchini, Tommaso; Gong, Cheng; Bai, Xue-Song

    2015-09-01

    An Eulerian stochastic fields (ESF) method accelerated with the chemistry coordinate mapping (CCM) approach for modelling spray combustion is formulated, and applied to model diesel combustion in a constant volume vessel. In ESF-CCM, the thermodynamic states of the discretised stochastic fields are mapped into a low-dimensional phase space. Integration of the chemical stiff ODEs is performed in the phase space and the results are mapped back to the physical domain. After validating the ESF-CCM, the method is used to investigate the effects of fuel cetane number on the structure of diesel spray combustion. It is shown that, depending of the fuel cetane number, liftoff length is varied, which can lead to a change in combustion mode from classical diesel spray combustion to fuel-lean premixed burned combustion. Spray combustion with a shorter liftoff length exhibits the characteristics of the classical conceptual diesel combustion model proposed by Dec in 1997 (http://dx.doi.org/10.4271/970873), whereas in a case with a lower cetane number the liftoff length is much larger and the spray combustion probably occurs in a fuel-lean-premixed mode of combustion. Nevertheless, the transport budget at the liftoff location shows that stabilisation at all cetane numbers is governed primarily by the auto-ignition process.

  13. Structure of sheared and rotating turbulence: Multiscale statistics of Lagrangian and Eulerian accelerations and passive scalar dynamics.

    PubMed

    Jacobitz, Frank G; Schneider, Kai; Bos, Wouter J T; Farge, Marie

    2016-01-01

    The acceleration statistics of sheared and rotating homogeneous turbulence are studied using direct numerical simulation results. The statistical properties of Lagrangian and Eulerian accelerations are considered together with the influence of the rotation to shear ratio, as well as the scale dependence of their statistics. The probability density functions (pdfs) of both Lagrangian and Eulerian accelerations show a strong and similar dependence on the rotation to shear ratio. The variance and flatness of both accelerations are analyzed and the extreme values of the Eulerian acceleration are observed to be above those of the Lagrangian acceleration. For strong rotation it is observed that flatness yields values close to three, corresponding to Gaussian-like behavior, and for moderate and vanishing rotation the flatness increases. Furthermore, the Lagrangian and Eulerian accelerations are shown to be strongly correlated for strong rotation due to a reduced nonlinear term in this case. A wavelet-based scale-dependent analysis shows that the flatness of both Eulerian and Lagrangian accelerations increases as scale decreases, which provides evidence for intermittent behavior. For strong rotation the Eulerian acceleration is even more intermittent than the Lagrangian acceleration, while the opposite result is obtained for moderate rotation. Moreover, the dynamics of a passive scalar with gradient production in the direction of the mean velocity gradient is analyzed and the influence of the rotation to shear ratio is studied. Concerning the concentration of a passive scalar spread by the flow, the pdf of its Eulerian time rate of change presents higher extreme values than those of its Lagrangian time rate of change. This suggests that the Eulerian time rate of change of scalar concentration is mainly due to advection, while its Lagrangian counterpart is only due to gradient production and viscous dissipation.

  14. Enzyme-accelerated and structure-guided crystallization of calcium carbonate: role of the carbonic anhydrase in the homologous system.

    PubMed

    Müller, Werner E G; Schlossmacher, Ute; Schröder, Heinz C; Lieberwirth, Ingo; Glasser, Gunnar; Korzhev, Michael; Neufurth, Meik; Wang, Xiaohong

    2014-01-01

    The calcareous spicules from sponges, e.g. from Sycon raphanus, are composed of almost pure calcium carbonate. In order to elucidate the formation of those structural skeletal elements, the function of the enzyme carbonic anhydrase (CA), isolated from this species, during the in vitro calcium carbonate-based spicule formation, was investigated. It is shown that the recombinant sponge CA substantially accelerates calcium carbonate formation in the in vitro diffusion assay. A stoichiometric calculation revealed that the turnover rate of the sponge CA during the calcification process amounts to 25 CO2s(-1) × molecule CA(-1). During this enzymatically driven process, initially pat-like particles are formed that are subsequently transformed to rhomboid/rhombohedroid crystals with a dimension of ~50 μm. The CA-catalyzed particles are smaller than those which are formed in the absence of the enzyme. The Martens hardness of the particles formed is ~4 GPa, a value which had been determined for other biogenic calcites. This conclusion is corroborated by energy-dispersive X-ray spectroscopy, which revealed that the particles synthesized are composed predominantly of the elements calcium, oxygen and carbon. Surprising was the finding, obtained by light and scanning electron microscopy, that the newly formed calcitic crystals associate with the calcareous spicules from S. raphanus in a highly ordered manner; the calcitic crystals almost perfectly arrange in an array orientation along the two opposing planes of the spicules, leaving the other two plane arrays uncovered. It is concluded that the CA is a key enzyme controlling the calcium carbonate biomineralization process, which directs the newly formed particles to existing calcareous spicular structures. It is expected that with the given tools new bioinspired materials can be fabricated. Copyright © 2013 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  15. Induction linear accelerators

    NASA Astrophysics Data System (ADS)

    Birx, Daniel

    1992-03-01

    Among the family of particle accelerators, the Induction Linear Accelerator is the best suited for the acceleration of high current electron beams. Because the electromagnetic radiation used to accelerate the electron beam is not stored in the cavities but is supplied by transmission lines during the beam pulse it is possible to utilize very low Q (typically<10) structures and very large beam pipes. This combination increases the beam breakup limited maximum currents to of order kiloamperes. The micropulse lengths of these machines are measured in 10's of nanoseconds and duty factors as high as 10-4 have been achieved. Until recently the major problem with these machines has been associated with the pulse power drive. Beam currents of kiloamperes and accelerating potentials of megavolts require peak power drives of gigawatts since no energy is stored in the structure. The marriage of liner accelerator technology and nonlinear magnetic compressors has produced some unique capabilities. It now appears possible to produce electron beams with average currents measured in amperes, peak currents in kiloamperes and gradients exceeding 1 MeV/meter, with power efficiencies approaching 50%. The nonlinear magnetic compression technology has replaced the spark gap drivers used on earlier accelerators with state-of-the-art all-solid-state SCR commutated compression chains. The reliability of these machines is now approaching 1010 shot MTBF. In the following paper we will briefly review the historical development of induction linear accelerators and then discuss the design considerations.

  16. Structure and Composition of the Distant Lunar Exosphere: Constraints from ARTEMIS Observations of Ion Acceleration in Time-Varying Fields

    NASA Technical Reports Server (NTRS)

    Halekas, J. S.; Poppe, A. R.; Farrell, W. M.; McFadden, J. P.

    2016-01-01

    By analyzing the trajectories of ionized constituents of the lunar exosphere in time-varying electromagnetic fields, we can place constraints on the composition, structure, and dynamics of the lunar exosphere. Heavy ions travel slower than light ions in the same fields, so by observing the lag between field rotations and the response of ions from the lunar exosphere, we can place constraints on the composition of the ions. Acceleration, Reconnection, Turbulence, and Electrodynamics of Moon's Interaction with the Sun (ARTEMIS) provides an ideal platform to utilize such an analysis, since its two-probe vantage allows precise timing of the propagation of field discontinuities in the solar wind, and its sensitive plasma instruments can detect the ion response. We demonstrate the utility of this technique by using fully time-dependent charged particle tracing to analyze several minutes of ion observations taken by the two ARTEMIS probes 3000-5000 km above the dusk terminator on 25 January 2014. The observations from this time period allow us to reach several interesting conclusions. The ion production at altitudes of a few hundred kilometers above the sunlit surface of the Moon has an unexpectedly significant contribution from species with masses of 40 amu or greater. The inferred distribution of the neutral source population has a large scale height, suggesting that micrometeorite impact vaporization and/or sputtering play an important role in the production of neutrals from the surface. Our observations also suggest an asymmetry in ion production, consistent with either a compositional variation in neutral vapor production or a local reduction in solar wind sputtering in magnetic regions of the surface.

  17. Structure and Composition of the Distant Lunar Exosphere: Constraints from ARTEMIS Observations of Ion Acceleration in Time-Varying Fields

    NASA Technical Reports Server (NTRS)

    Halekas, J. S.; Poppe, A. R.; Farrell, W. M.; McFadden, J. P.

    2016-01-01

    By analyzing the trajectories of ionized constituents of the lunar exosphere in time-varying electromagnetic fields, we can place constraints on the composition, structure, and dynamics of the lunar exosphere. Heavy ions travel slower than light ions in the same fields, so by observing the lag between field rotations and the response of ions from the lunar exosphere, we can place constraints on the composition of the ions. Acceleration, Reconnection, Turbulence, and Electrodynamics of Moon's Interaction with the Sun (ARTEMIS) provides an ideal platform to utilize such an analysis, since its two-probe vantage allows precise timing of the propagation of field discontinuities in the solar wind, and its sensitive plasma instruments can detect the ion response. We demonstrate the utility of this technique by using fully time-dependent charged particle tracing to analyze several minutes of ion observations taken by the two ARTEMIS probes 3000-5000 km above the dusk terminator on 25 January 2014. The observations from this time period allow us to reach several interesting conclusions. The ion production at altitudes of a few hundred kilometers above the sunlit surface of the Moon has an unexpectedly significant contribution from species with masses of 40 amu or greater. The inferred distribution of the neutral source population has a large scale height, suggesting that micrometeorite impact vaporization and/or sputtering play an important role in the production of neutrals from the surface. Our observations also suggest an asymmetry in ion production, consistent with either a compositional variation in neutral vapor production or a local reduction in solar wind sputtering in magnetic regions of the surface.

  18. Structure and composition of the distant lunar exosphere: Constraints from ARTEMIS observations of ion acceleration in time-varying fields

    NASA Astrophysics Data System (ADS)

    Halekas, J. S.; Poppe, A. R.; Farrell, W. M.; McFadden, J. P.

    2016-06-01

    By analyzing the trajectories of ionized constituents of the lunar exosphere in time-varying electromagnetic fields, we can place constraints on the composition, structure, and dynamics of the lunar exosphere. Heavy ions travel slower than light ions in the same fields, so by observing the lag between field rotations and the response of ions from the lunar exosphere, we can place constraints on the composition of the ions. Acceleration, Reconnection, Turbulence, and Electrodynamics of Moon's Interaction with the Sun (ARTEMIS) provides an ideal platform to utilize such an analysis, since its two-probe vantage allows precise timing of the propagation of field discontinuities in the solar wind, and its sensitive plasma instruments can detect the ion response. We demonstrate the utility of this technique by using fully time-dependent charged particle tracing to analyze several minutes of ion observations taken by the two ARTEMIS probes ~3000-5000 km above the dusk terminator on 25 January 2014. The observations from this time period allow us to reach several interesting conclusions. The ion production at altitudes of a few hundred kilometers above the sunlit surface of the Moon has an unexpectedly significant contribution from species with masses of 40 amu or greater. The inferred distribution of the neutral source population has a large scale height, suggesting that micrometeorite impact vaporization and/or sputtering play an important role in the production of neutrals from the surface. Our observations also suggest an asymmetry in ion production, consistent with either a compositional variation in neutral vapor production or a local reduction in solar wind sputtering in magnetic regions of the surface.

  19. The Atomki accelerator center

    NASA Astrophysics Data System (ADS)

    Vajda, I.; Fülöp, Zs.; Biri, S.

    2017-06-01

    Particle accelerators are the driving forces of nuclear physics laboratories and MTA Atomki, the Institute for Nuclear Research of the Hungarian Academy of Sciences is no exception. The Atomki Accelerator Center (AAC) incorporates several low-energy charged-particle accelerators, offering the possibility of choosing ions with various charge states, energies and beam intensities. Currently, the AAC has six main facilities: a cyclotron (K=20), two Van de Graaff accelerators (1 MV, 5 MV), an ECR ion source, an electromagnetic isotope separator and a 2 MV Tandetron installed in 2015. The accelerators, spanning a range of beam energies from 50 eV to 27 MeV, have been designed for a broad range of research projects and applications in various fields - mainly in nuclear and atomic physics, materials science, environmental research and archaeology. The structure of the laboratory with a short description of the most important topics, education and outreach activities are presented.

  20. Radical Acceleration

    ERIC Educational Resources Information Center

    Gross, Miraca U. M.; Van Vliet, Helen E.

    2005-01-01

    Research has found that teachers' objections to accelerating gifted students are mainly based on a fear that acceleration will lead to social or emotional damage. Ironically, it is the academic and emotional maturity which characterizes intellectually gifted students, coupled with their high levels of academic achievement, which makes them such…

  1. RECIRCULATING ACCELERATION

    SciTech Connect

    BERG,J.S.; GARREN,A.A.; JOHNSTONE,C.

    2000-04-07

    This paper compares various types of recirculating accelerators, outlining the advantages and disadvantages of various approaches. The accelerators are characterized according to the types of arcs they use: whether there is a single arc for the entire recirculator or there are multiple arcs, and whether the arc(s) are isochronous or non-isochronous.

  2. Vibration control in accelerators

    SciTech Connect

    Montag, C.

    2011-01-01

    In the vast majority of accelerator applications, ground vibration amplitudes are well below tolerable magnet jitter amplitudes. In these cases, it is necessary and sufficient to design a rigid magnet support structure that does not amplify ground vibration. Since accelerator beam lines are typically installed at an elevation of 1-2m above ground level, special care has to be taken in order to avoid designing a support structure that acts like an inverted pendulum with a low resonance frequency, resulting in untolerable lateral vibration amplitudes of the accelerator components when excited by either ambient ground motion or vibration sources within the accelerator itself, such as cooling water pumps or helium flow in superconducting magnets. In cases where ground motion amplitudes already exceed the required jiter tolerances, for instance in future linear colliders, passive vibration damping or active stabilization may be considered.

  3. LINEAR ACCELERATOR

    DOEpatents

    Colgate, S.A.

    1958-05-27

    An improvement is presented in linear accelerators for charged particles with respect to the stable focusing of the particle beam. The improvement consists of providing a radial electric field transverse to the accelerating electric fields and angularly introducing the beam of particles in the field. The results of the foregoing is to achieve a beam which spirals about the axis of the acceleration path. The combination of the electric fields and angular motion of the particles cooperate to provide a stable and focused particle beam.

  4. Wakefield accelerators

    SciTech Connect

    Simpson, J.D.

    1990-01-01

    The search for new methods to accelerate particle beams to high energy using high gradients has resulted in a number of candidate schemes. One of these, wakefield acceleration, has been the subject of considerable R D in recent years. This effort has resulted in successful proof of principle experiments and in increased understanding of many of the practical aspects of the technique. Some wakefield basics plus the status of existing and proposed experimental work is discussed, along with speculations on the future of wake field acceleration. 10 refs., 6 figs.

  5. ION ACCELERATOR

    DOEpatents

    Bell, J.S.

    1959-09-15

    An arrangement for the drift tubes in a linear accelerator is described whereby each drift tube acts to shield the particles from the influence of the accelerating field and focuses the particles passing through the tube. In one embodiment the drift tube is splii longitudinally into quadrants supported along the axis of the accelerator by webs from a yoke, the quadrants. webs, and yoke being of magnetic material. A magnetic focusing action is produced by energizing a winding on each web to set up a magnetic field between adjacent quadrants. In the other embodiment the quadrants are electrically insulated from each other and have opposite polarity voltages on adjacent quadrants to provide an electric focusing fleld for the particles, with the quadrants spaced sufficienily close enough to shield the particles within the tube from the accelerating electric field.

  6. Acceleration switch

    DOEpatents

    Abbin, J.P. Jr.; Devaney, H.F.; Hake, L.W.

    1979-08-29

    The disclosure relates to an improved integrating acceleration switch of the type having a mass suspended within a fluid filled chamber, with the motion of the mass initially opposed by a spring and subsequently not so opposed.

  7. Acceleration switch

    DOEpatents

    Abbin, Jr., Joseph P.; Devaney, Howard F.; Hake, Lewis W.

    1982-08-17

    The disclosure relates to an improved integrating acceleration switch of the type having a mass suspended within a fluid filled chamber, with the motion of the mass initially opposed by a spring and subsequently not so opposed.

  8. Cluster Multipoint Observations of the Spatial Structure and Time Development of Auroral Acceleration Region Field-aligned Current Systems, Potentials, and Plasma

    NASA Astrophysics Data System (ADS)

    Hull, A. J.; Chaston, C. C.; Fillingim, M. O.; Frey, H. U.; Bonnell, J. W.; Mozer, F.; Goldstein, M. L.

    2014-12-01

    The auroral acceleration region is an integral part of the magnetosphere-ionosphere electrodynamic system, and plays a key role in the transport of plasma and energy between Earth and space. This region is embedded with field-aligned currents that couple the magnetosphere to the ionosphere and is where parallel electric fields form that accelerate plasma to and from these regions. Though considerable progress has been made, the complex interplay between field-aligned current system formation, the development of parallel electric fields, changes in the plasma constituents, and auroral emissions consequences are not fully understood. The Cluster mission is well suited for studying the structure and dynamics of the auroral acceleration region. Over its lifetime, Cluster has sampled much of this region with closely spaced probes enabling the distinction between temporal effects from spatial variations. Moreover, this data when combined with auroral images from IMAGE or THEMIS GBO-ASI enable an assessment of the auroral emission response to spatial morphology and temporal development of structures seeded in the auroral acceleration region. In this study we present a survey of Cluster multi-point traversals within and just above the auroral acceleration region (≤ 3 Re altitude). In particular we highlight the spatial morphology and developmental sequence of auroral acceleration current systems, potentials and plasma constituents, with the aim of identifying controlling factors, and assessing ionospheric consequences under different conditions. Our results suggest that the "Alfvénic" activity may be an important precursor and perhaps may be playing an essential role in the development of "quasi-static" current systems during quiet and substorm active times. Such events are generally the result of an injection mediated process at or near the plasma sheet boundary layer, resulting in the local expansion of the plasma sheet. Key features of the conversion from Alfv

  9. LINEAR ACCELERATOR

    DOEpatents

    Christofilos, N.C.; Polk, I.J.

    1959-02-17

    Improvements in linear particle accelerators are described. A drift tube system for a linear ion accelerator reduces gap capacity between adjacent drift tube ends. This is accomplished by reducing the ratio of the diameter of the drift tube to the diameter of the resonant cavity. Concentration of magnetic field intensity at the longitudinal midpoint of the external sunface of each drift tube is reduced by increasing the external drift tube diameter at the longitudinal center region.

  10. RF Measurements on DXRL (Deep X-ray Li-thog-ra-phy)-Fabricated mmWave Accelerating Cavity Structures at the Advanced Photon Source (APS)

    NASA Astrophysics Data System (ADS)

    Song, J. J.; Kang, Y. W.

    1997-05-01

    Recently rf structures have been proposed for frequencies in the mmwave (30--300 GHz) range. This miniaturization is feasible with a 3-D micromachining process known as LIGA (German acronym for lithographe, galvanoformung, und abformung) or DXRL (deep x-ray lithography).(J.J. Song, et. al, ``LIGA-Fabrication of mmWave Accelerating Cavity Structures at the Advanced Photon Source (APS),'' these proceedings.) A 32-cell 108-GHz constant-impedance cavity and a 66-cell 94-GHz constant-gradient cavity were fabricated using DXRL micromachining with the synchrotron radiation sources at NSLS and APS. Their eventual application could be parts of linear accelerators, microwave undulators, or free-electron lasers. Radiofrequency measurement on the structures was performed by the bead-perturbation method with e-beam sputtered aluminum beads. The form factor of the bead was measured with the pillbox cavity and compared with the calculation. This paper will describe the rf measur! ement on the mmwave cavity structure.

  11. CLASHING BEAM PARTICLE ACCELERATOR

    DOEpatents

    Burleigh, R.J.

    1961-04-11

    A charged-particle accelerator of the proton synchrotron class having means for simultaneously accelerating two separate contra-rotating particle beams within a single annular magnet structure is reported. The magnet provides two concentric circular field regions of opposite magnetic polarity with one field region being of slightly less diameter than the other. The accelerator includes a deflector means straddling the two particle orbits and acting to collide the two particle beams after each has been accelerated to a desired energy. The deflector has the further property of returning particles which do not undergo collision to the regular orbits whereby the particles recirculate with the possibility of colliding upon subsequent passages through the deflector.

  12. Novel durable bio-photocatalyst purifiers, a non-heterogeneous mechanism: accelerated entrapped dye degradation into structural polysiloxane-shield nano-reactors.

    PubMed

    Dastjerdi, Roya; Montazer, Majid; Shahsavan, Shadi; Böttcher, Horst; Moghadam, M B; Sarsour, Jamal

    2013-01-01

    This research has designed innovative Ag/TiO(2) polysiloxane-shield nano-reactors on the PET fabric to develop novel durable bio-photocatalyst purifiers. To create these very fine nano-reactors, oppositely surface charged multiple size nanoparticles have been applied accompanied with a crosslinkable amino-functionalized polysiloxane (XPs) emulsion. Investigation of photocatalytic dye decolorization efficiency revealed a non-heterogeneous mechanism including an accelerated degradation of entrapped dye molecules into the structural polysiloxane-shield nano-reactors. In fact, dye molecules can be adsorbed by both Ag and XPs due to their electrostatic interactions and/or even via forming a complex with them especially with silver NPs. The absorbed dye and active oxygen species generated by TiO(2) were entrapped by polysiloxane shelter and the presence of silver nanoparticles further attract the negative oxygen species closer to the adsorbed dye molecules. In this way, the dye molecules are in close contact with concentrated active oxygen species into the created nano-reactors. This provides an accelerated degradation of dye molecules. This non-heterogeneous mechanism has been detected on the sample containing all of the three components. Increasing the concentration of Ag and XPs accelerated the second step beginning with an enhanced rate. Further, the treated samples also showed an excellent antibacterial activity.

  13. An attempt to validate the ultra-accelerated microbar and the concrete performance test with the degree of AAR-induced damage observed in concrete structures

    SciTech Connect

    Leemann, Andreas; Merz, Christine

    2013-07-15

    There is little knowledge about the relation between AAR-induced damage observed in structures and the expansion potential obtained with accelerated tests. In this study, aggregates used in structures damaged by AAR were tested with the microbar test (MBT/AFNOR XP 18-594) and the concrete performance test (CPT/AFNOR P18-454). After the tests, the samples were examined using optical and scanning electron microscopy. Based on the results, the significance of the microbar test has to be examined very critically. The agreement of measured expansion, reacted rock types and the composition of the reaction products between the on-site concrete and the reproduced concrete subjected to the CPT clearly indicates that the reaction mechanisms in the structure and in the concrete performance test are comparable. As such, the concrete performance test seems to be an appropriate tool to test the potential reactivity of specific concrete mixtures.

  14. Single-shot, ultrafast diagnostics of light-speed plasma structures and accelerating GeV electrons

    NASA Astrophysics Data System (ADS)

    Chang, Yen-Yu; Shaw, Joseph M.; Welch, James; Weichman, Kathleen; Hannasch, Andrea; LaBerge, Maxwell; Henderson, Watson; Zgadzaj, Rafal; Bernstein, Aaron; Downer, Mike

    2017-03-01

    We have experimentally demonstrated ultrafast diagnostics to visualize the laser wakefield acceleration process in a single-shot mode. We measured the Faraday rotation of a probe pulse due to the magnetic field induced by GeV electrons in low-density plasmas. In addition, we improved the temporal resolution of Frequency Domain Streak Camera (FDSC) to ˜10 fs by broadening the bandwidth of the probe beam, enabling visualization of the bubble dynamics. A prototype experiment using the broad bandwidth FDSC was performed.

  15. Acceleration Studies

    NASA Technical Reports Server (NTRS)

    Rogers, Melissa J. B.

    1993-01-01

    Work to support the NASA MSFC Acceleration Characterization and Analysis Project (ACAP) was performed. Four tasks (analysis development, analysis research, analysis documentation, and acceleration analysis) were addressed by parallel projects. Work concentrated on preparation for and implementation of near real-time SAMS data analysis during the USMP-1 mission. User support documents and case specific software documentation and tutorials were developed. Information and results were presented to microgravity users. ACAP computer facilities need to be fully implemented and networked, data resources must be cataloged and accessible, future microgravity missions must be coordinated, and continued Orbiter characterization is necessary.

  16. Active vibration control of structure by Active Mass Damper and Multi-Modal Negative Acceleration Feedback control algorithm

    NASA Astrophysics Data System (ADS)

    Yang, Don-Ho; Shin, Ji-Hwan; Lee, HyunWook; Kim, Seoug-Ki; Kwak, Moon K.

    2017-03-01

    In this study, an Active Mass Damper (AMD) consisting of an AC servo motor, a movable mass connected to the AC servo motor by a ball-screw mechanism, and an accelerometer as a sensor for vibration measurement were considered. Considering the capability of the AC servo motor which can follow the desired displacement accurately, the Negative Acceleration Feedback (NAF) control algorithm which uses the acceleration signal directly and produces the desired displacement for the active mass was proposed. The effectiveness of the NAF control was proved theoretically using a single-degree-of-freedom (SDOF) system. It was found that the stability condition for the NAF control is static and it can effectively increase the damping of the target natural mode without causing instability in the low frequency region. Based on the theoretical results of the SDOF system, the Multi-Modal NAF (MMNAF) control is proposed to suppress the many natural modes of multi-degree-of-freedom (MDOF) systems using a single AMD. It was proved both theoretically and experimentally that the MMNAF control can suppress vibrations of the MDOF system.

  17. Prospects in Nuclear Structure and Reactions with New Generation of High Power Accelerators and Innovative Instrumentation in Europe

    NASA Astrophysics Data System (ADS)

    Gales, S.

    2014-09-01

    The advent of high power light and heavy ion accelerators producing intense secondary radioactive ion beams (RIB) made possible the exploration of a new territory of nuclei with extreme in Mass and/or N/Z ratios. To pursue the investigation of this "terra incognita" several projects, based on second generation accelerators producing intense stables and RIB, all aiming at the increase by several orders of magnitude of the RIB intensities are now under construction and/or planned for the end of this decade in the world. In Europe RIB production at SPES@Legnaro, SPIRAL2@GANIL, ALTO@Orsay and HIE-ISOLDE@CERN are based on the ISOL method, whereas FAIR@GSI with the new Super-FRS fragment-separator takes advantage of the "In Flight" technique. Projects of high intensity heavy ions, and low energy drivers (< 10 MeV/n) are also foreseen at Flerov Laboratory @DUBNA, GSI, and GANIL. Technical performances, innovative new instrumentation and methods, and keys experiments in connection with these second generation high intensity facilities will be reviewed.

  18. Accelerators for America's Future

    NASA Astrophysics Data System (ADS)

    Bai, Mei

    2016-03-01

    Particle accelerator, a powerful tool to energize beams of charged particles to a desired speed and energy, has been the working horse for investigating the fundamental structure of matter and fundermental laws of nature. Most known examples are the 2-mile long Stanford Linear Accelerator at SLAC, the high energy proton and anti-proton collider Tevatron at FermiLab, and Large Hadron Collider that is currently under operation at CERN. During the less than a century development of accelerator science and technology that led to a dazzling list of discoveries, particle accelerators have also found various applications beyond particle and nuclear physics research, and become an indispensible part of the economy. Today, one can find a particle accelerator at almost every corner of our lives, ranging from the x-ray machine at the airport security to radiation diagnostic and therapy in hospitals. This presentation will give a brief introduction of the applications of this powerful tool in fundermental research as well as in industry. Challenges in accelerator science and technology will also be briefly presented

  19. APT accelerator technology

    SciTech Connect

    Schneider, J.D.

    1996-09-01

    Proposed accelerator production of tritium (APT) project requires an accelerator providing a cw proton beam of 100 mA at 1300 MeV. Since most of the technical risk of a high-current cw (continuous-wave, 100% DF) accelerator resides in the low-energy section, Los Alamos is building a 20 MeV duplicate of the accelerator front end to confirm design codes, beam performance, and demonstrate operaional reliability. We report on design details of this low-energy demonstration accelerator (LEDA) and discuss the integrated design of the full accelerator for the APT plant. LEDA`s proton injector is under test and has produced more than 130 mA at 75 keV. Fabrication is proceeding on a 6.7-KeV, 8-m long RFQ, and detailed design is underway on coupled-cavity drift-tube linac (CCDTL) structures. Detailed design and technology experiments are underway on medium-beta superconducting cavities to assess feasibility of replacing the conventional (room-temperature copper) high-energy linac with a linac made of niobium superconducting RF cavities.

  20. Accelerated Achievement

    ERIC Educational Resources Information Center

    Ford, William J.

    2010-01-01

    This article focuses on the accelerated associate degree program at Ivy Tech Community College (Indiana) in which low-income students will receive an associate degree in one year. The three-year pilot program is funded by a $2.3 million grant from the Lumina Foundation for Education in Indianapolis and a $270,000 grant from the Indiana Commission…

  1. ACCELERATION INTEGRATOR

    DOEpatents

    Pope, K.E.

    1958-01-01

    This patent relates to an improved acceleration integrator and more particularly to apparatus of this nature which is gyrostabilized. The device may be used to sense the attainment by an airborne vehicle of a predetermined velocitv or distance along a given vector path. In its broad aspects, the acceleration integrator utilizes a magnetized element rotatable driven by a synchronous motor and having a cylin drical flux gap and a restrained eddy- current drag cap deposed to move into the gap. The angular velocity imparted to the rotatable cap shaft is transmitted in a positive manner to the magnetized element through a servo feedback loop. The resultant angular velocity of tae cap is proportional to the acceleration of the housing in this manner and means may be used to measure the velocity and operate switches at a pre-set magnitude. To make the above-described dcvice sensitive to acceleration in only one direction the magnetized element forms the spinning inertia element of a free gyroscope, and the outer housing functions as a gimbal of a gyroscope.

  2. Plasma accelerator

    DOEpatents

    Wang, Zhehui; Barnes, Cris W.

    2002-01-01

    There has been invented an apparatus for acceleration of a plasma having coaxially positioned, constant diameter, cylindrical electrodes which are modified to converge (for a positive polarity inner electrode and a negatively charged outer electrode) at the plasma output end of the annulus between the electrodes to achieve improved particle flux per unit of power.

  3. Accelerated Achievement

    ERIC Educational Resources Information Center

    Ford, William J.

    2010-01-01

    This article focuses on the accelerated associate degree program at Ivy Tech Community College (Indiana) in which low-income students will receive an associate degree in one year. The three-year pilot program is funded by a $2.3 million grant from the Lumina Foundation for Education in Indianapolis and a $270,000 grant from the Indiana Commission…

  4. Advanced accelerator theory development

    SciTech Connect

    Sampayan, S.E.; Houck, T.L.; Poole, B.; Tishchenko, N.; Vitello, P.A.; Wang, I.

    1998-02-09

    A new accelerator technology, the dielectric wall accelerator (DWA), is potentially an ultra compact accelerator/pulsed power driver. This new accelerator relies on three new components: the ultra-high gradient insulator, the asymmetric Blumlein and low jitter switches. In this report, we focused our attention on the first two components of the DWA system the insulators and the asymmetric Blumlein. First, we sought to develop the necessary design tools to model and scale the behavior of the high gradient insulator. To perform this task we concentrated on modeling the discharge processes (i.e., initiation and creation of the surface discharge). In addition, because these high gradient structures exhibit favorable microwave properties in certain accelerator configurations, we performed experiments and calculations to determine the relevant electromagnetic properties. Second, we performed circuit modeling to understand energy coupling to dynamic loads by the asymmetric Blumlein. Further, we have experimentally observed a non-linear coupling effect in certain asymmetric Blumlein configurations. That is, as these structures are stacked into a complete module, the output voltage does not sum linearly and a lower than expected output voltage results. Although we solved this effect experimentally, we performed calculations to understand this effect more fully to allow better optimization of this DWA pulse-forming line system.

  5. Linear induction accelerator

    DOEpatents

    Buttram, M.T.; Ginn, J.W.

    1988-06-21

    A linear induction accelerator includes a plurality of adder cavities arranged in a series and provided in a structure which is evacuated so that a vacuum inductance is provided between each adder cavity and the structure. An energy storage system for the adder cavities includes a pulsed current source and a respective plurality of bipolar converting networks connected thereto. The bipolar high-voltage, high-repetition-rate square pulse train sets and resets the cavities. 4 figs.

  6. Particle Accelerators in China

    NASA Astrophysics Data System (ADS)

    Zhang, Chuang; Fang, Shouxian

    As the special machines that can accelerate charged particle beams to high energy by using electromagnetic fields, particle accelerators have been widely applied in scientific research and various areas of society. The development of particle accelerators in China started in the early 1950s. After a brief review of the history of accelerators, this article describes in the following sections: particle colliders, heavy-ion accelerators, high-intensity proton accelerators, accelerator-based light sources, pulsed power accelerators, small scale accelerators, accelerators for applications, accelerator technology development and advanced accelerator concepts. The prospects of particle accelerators in China are also presented.

  7. Compact accelerator

    DOEpatents

    Caporaso, George J.; Sampayan, Stephen E.; Kirbie, Hugh C.

    2007-02-06

    A compact linear accelerator having at least one strip-shaped Blumlein module which guides a propagating wavefront between first and second ends and controls the output pulse at the second end. Each Blumlein module has first, second, and third planar conductor strips, with a first dielectric strip between the first and second conductor strips, and a second dielectric strip between the second and third conductor strips. Additionally, the compact linear accelerator includes a high voltage power supply connected to charge the second conductor strip to a high potential, and a switch for switching the high potential in the second conductor strip to at least one of the first and third conductor strips so as to initiate a propagating reverse polarity wavefront(s) in the corresponding dielectric strip(s).

  8. Compact accelerator for medical therapy

    DOEpatents

    Caporaso, George J.; Chen, Yu-Jiuan; Hawkins, Steven A.; Sampayan, Stephen E.; Paul, Arthur C.

    2010-05-04

    A compact accelerator system having an integrated particle generator-linear accelerator with a compact, small-scale construction capable of producing an energetic (.about.70-250 MeV) proton beam or other nuclei and transporting the beam direction to a medical therapy patient without the need for bending magnets or other hardware often required for remote beam transport. The integrated particle generator-accelerator is actuable as a unitary body on a support structure to enable scanning of a particle beam by direction actuation of the particle generator-accelerator.

  9. High field gradient particle accelerator

    DOEpatents

    Nation, John A.; Greenwald, Shlomo

    1989-01-01

    A high electric field gradient electron accelerator utilizing short duration, microwave radiation, and capable of operating at high field gradients for high energy physics applications or at reduced electric field gradients for high average current intermediate energy accelerator applications. Particles are accelerated in a smooth bore, periodic undulating waveguide, wherein the period is so selected that the particles slip an integral number of cycles of the r.f. wave every period of the structure. This phase step of the particles produces substantially continuous acceleration in a traveling wave without transverse magnetic or other guide means for the particle.

  10. High field gradient particle accelerator

    DOEpatents

    Nation, J.A.; Greenwald, S.

    1989-05-30

    A high electric field gradient electron accelerator utilizing short duration, microwave radiation, and capable of operating at high field gradients for high energy physics applications or at reduced electric field gradients for high average current intermediate energy accelerator applications is disclosed. Particles are accelerated in a smooth bore, periodic undulating waveguide, wherein the period is so selected that the particles slip an integral number of cycles of the r.f. wave every period of the structure. This phase step of the particles produces substantially continuous acceleration in a traveling wave without transverse magnetic or other guide means for the particle. 10 figs.

  11. Measurement of ion species in high current ECR H{sup +}/D{sup +} ion source for IFMIF (International Fusion Materials Irradiation Facility)

    SciTech Connect

    Shinto, K. Ichimiya, R.; Ihara, A.; Ikeda, Y.; Kasugai, A.; Kitano, T.; Kondo, K.; Takahashi, H.; Senée, F.; Bolzon, B.; Chauvin, N.; Gobin, R.; Valette, M.

    2016-02-15

    Ion species ratio of high current positive hydrogen/deuterium ion beams extracted from an electron-cyclotron-resonance ion source for International Fusion Materials Irradiation Facility accelerator was measured by the Doppler shift Balmer-α line spectroscopy. The proton (H{sup +}) ratio at the middle of the low energy beam transport reached 80% at the hydrogen ion beam extraction of 100 keV/160 mA and the deuteron (D{sup +}) ratio reached 75% at the deuterium ion beam extraction of 100 keV/113 mA. It is found that the H{sup +} ratio measured by the spectroscopy gives lower than that derived from the phase-space diagram measured by an Allison scanner type emittance monitor. The H{sup +}/D{sup +} ratio estimated by the emittance monitor was more than 90% at those extraction currents.

  12. Measurement of ion species in high current ECR H⁺/D⁺ ion source for IFMIF (International Fusion Materials Irradiation Facility).

    PubMed

    Shinto, K; Senée, F; Ayala, J-M; Bolzon, B; Chauvin, N; Gobin, R; Ichimiya, R; Ihara, A; Ikeda, Y; Kasugai, A; Kitano, T; Kondo, K; Marqueta, A; Okumura, Y; Takahashi, H; Valette, M

    2016-02-01

    Ion species ratio of high current positive hydrogen/deuterium ion beams extracted from an electron-cyclotron-resonance ion source for International Fusion Materials Irradiation Facility accelerator was measured by the Doppler shift Balmer-α line spectroscopy. The proton (H(+)) ratio at the middle of the low energy beam transport reached 80% at the hydrogen ion beam extraction of 100 keV/160 mA and the deuteron (D(+)) ratio reached 75% at the deuterium ion beam extraction of 100 keV/113 mA. It is found that the H(+) ratio measured by the spectroscopy gives lower than that derived from the phase-space diagram measured by an Allison scanner type emittance monitor. The H(+)/D(+) ratio estimated by the emittance monitor was more than 90% at those extraction currents.

  13. MUON ACCELERATION

    SciTech Connect

    BERG,S.J.

    2003-11-18

    One of the major motivations driving recent interest in FFAGs is their use for the cost-effective acceleration of muons. This paper summarizes the progress in this area that was achieved leading up to and at the FFAG workshop at KEK from July 7-12, 2003. Much of the relevant background and references are also given here, to give a context to the progress we have made.

  14. BICEP's acceleration

    SciTech Connect

    Contaldi, Carlo R.

    2014-10-01

    The recent Bicep2 [1] detection of, what is claimed to be primordial B-modes, opens up the possibility of constraining not only the energy scale of inflation but also the detailed acceleration history that occurred during inflation. In turn this can be used to determine the shape of the inflaton potential V(φ) for the first time — if a single, scalar inflaton is assumed to be driving the acceleration. We carry out a Monte Carlo exploration of inflationary trajectories given the current data. Using this method we obtain a posterior distribution of possible acceleration profiles ε(N) as a function of e-fold N and derived posterior distributions of the primordial power spectrum P(k) and potential V(φ). We find that the Bicep2 result, in combination with Planck measurements of total intensity Cosmic Microwave Background (CMB) anisotropies, induces a significant feature in the scalar primordial spectrum at scales k∼ 10{sup -3} Mpc {sup -1}. This is in agreement with a previous detection of a suppression in the scalar power [2].

  15. Laser acceleration

    NASA Astrophysics Data System (ADS)

    Tajima, T.; Nakajima, K.; Mourou, G.

    2017-02-01

    The fundamental idea of Laser Wakefield Acceleration (LWFA) is reviewed. An ultrafast intense laser pulse drives coherent wakefield with a relativistic amplitude robustly supported by the plasma. While the large amplitude of wakefields involves collective resonant oscillations of the eigenmode of the entire plasma electrons, the wake phase velocity ˜ c and ultrafastness of the laser pulse introduce the wake stability and rigidity. A large number of worldwide experiments show a rapid progress of this concept realization toward both the high-energy accelerator prospect and broad applications. The strong interest in this has been spurring and stimulating novel laser technologies, including the Chirped Pulse Amplification, the Thin Film Compression, the Coherent Amplification Network, and the Relativistic Mirror Compression. These in turn have created a conglomerate of novel science and technology with LWFA to form a new genre of high field science with many parameters of merit in this field increasing exponentially lately. This science has triggered a number of worldwide research centers and initiatives. Associated physics of ion acceleration, X-ray generation, and astrophysical processes of ultrahigh energy cosmic rays are reviewed. Applications such as X-ray free electron laser, cancer therapy, and radioisotope production etc. are considered. A new avenue of LWFA using nanomaterials is also emerging.

  16. Particle acceleration in pulsar magnetospheres

    NASA Technical Reports Server (NTRS)

    Baker, K. B.

    1978-01-01

    The structure of pulsar magnetospheres and the acceleration mechanism for charged particles in the magnetosphere was studied using a pulsar model which required large acceleration of the particles near the surface of the star. A theorem was developed which showed that particle acceleration cannot be expected when the angle between the magnetic field lines and the rotation axis is constant (e.g. radial field lines). If this angle is not constant, however, acceleration must occur. The more realistic model of an axisymmetric neutron star with a strong dipole magnetic field aligned with the rotation axis was investigated. In this case, acceleration occurred at large distances from the surface of the star. The magnitude of the current can be determined using the model presented. In the case of nonaxisymmetric systems, the acceleration is expected to occur nearer to the surface of the star.

  17. Laser acceleration and its future

    PubMed Central

    Tajima, Toshiki

    2010-01-01

    Laser acceleration is based on the concept to marshal collective fields that may be induced by laser. In order to exceed the material breakdown field by a large factor, we employ the broken-down matter of plasma. While the generated wakefields resemble with the fields in conventional accelerators in their structure (at least qualitatively), it is their extreme accelerating fields that distinguish the laser wakefield from others, amounting to tiny emittance and compact accelerator. The current research largely falls on how to master the control of acceleration process in spatial and temporal scales several orders of magnitude smaller than the conventional method. The efforts over the last several years have come to a fruition of generating good beam properties with GeV energies on a table top, leading to many applications, such as ultrafast radiolysis, intraoperative radiation therapy, injection to X-ray free electron laser, and a candidate for future high energy accelerators. PMID:20228616

  18. Low-symmetric coherent structures and dimensional crossover in Rayleigh Taylor flows driven by time dependent accelerations

    NASA Astrophysics Data System (ADS)

    Bhowmick, Aklant; Abarzhi, Snezhana

    2016-11-01

    We investigate the nature of the dimensional crossover i.e. transition between the nearly isotropic 3D periodic flows with group p4mm (square) to highly anisotropic 2D periodic flows with group p2m1 in Rayleigh Taylor (RT) instability. Power law time dependence of the acceleration is considered with the emphasis on sub-regime, where the behavior is the RT type. We consider flow with group p2mm (rectangle) and obtain the 3D square and 2D limits with leading order rectangular corrections. Regular asymptotic solutions evolve as power law and form a two parameter family parametrized by the principal curvatures of the bubble. The bubbles with "near circular contour" separate the 2-dimensional solution space into two sub-regimes having distinct properties under the dimensional crossover. In one sub-regime, the elongated bubbles transform to 2D solutions, whereas in the other they flatten. 3D square bubbles are universally stable whereas 2D bubbles are unstable with respect to 3D modulations, implying that the dimensional crossover is discontinuous. We find that the time dependence affects the growth/decay of perturbations and has no consequence on the overall stability properties of the solution. The work is supported by the US National Science Foundation.

  19. Laser Ion Acceleration Control

    NASA Astrophysics Data System (ADS)

    Kawata, Shigeo; Nagashima, T.; Izumiyama, T.; Sato, D.; Takano, M.; Barada, D.; Ma, Y. Y.; Gu, Y. J.; Kong, Q.; Wang, P. X.; Wang, W. M.

    2013-10-01

    An intense femtosecond pulsed laser is employed to accelerate ions. The issues in the laser ion accelerator include the energy efficiency from the laser to the ions, the ion beam collimation, the ion energy spectrum control, the ion beam bunching, the ion particle energy control, etc. In the study particle computer simulations were performed to solve the issues, and each component was designed to control the ion beam quality. When an intense laser illuminates a target, electrons in the target are accelerated and leave from the target; temporarily a strong electric field is formed between the high-energy electrons and the target ions, and the target ions are accelerated. The energy efficiency from the laser to ions was improved by using a solid target with a fine sub-wavelength structure or by a near critical density gas plasma. The ion beam collimation was realized by holes behind the solid target. The control of the ion energy spectrum and the ion particle energy, and the ion beam bunching were successfully realized by a multi-stage laser-target interaction. The present study proposed a novel concept for a future compact laser ion accelerator, based on each component study required to control the ion beam quality and parameters. Partly supported by JSPS, MEXT, CORE, Japan/US Cooperation program, ASHULA and ILE/Osaka University.

  20. Advanced concepts for acceleration

    SciTech Connect

    Keefe, D.

    1986-07-01

    Selected examples of advanced accelerator concepts are reviewed. Such plasma accelerators as plasma beat wave accelerator, plasma wake field accelerator, and plasma grating accelerator are discussed particularly as examples of concepts for accelerating relativistic electrons or positrons. Also covered are the pulsed electron-beam, pulsed laser accelerator, inverse Cherenkov accelerator, inverse free-electron laser, switched radial-line accelerators, and two-beam accelerator. Advanced concepts for ion acceleration discussed include the electron ring accelerator, excitation of waves on intense electron beams, and two-wave combinations. (LEW)