DESIGN AND DEVELOPMENT REPORT ON TREAT CONTROL ROD DRIVE II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Batch, R.V.

1961-05-01

A discussion is given of the development of TREAT control rod drive II, which describes the basic design, the problems involved with the design, the various design methods pursued, the testing procedures, and the evaluation of the performance characteristics of the final drive. (B.O.G.)

Design of two-dimensional channels with prescribed velocity distributions along the channel walls

NASA Technical Reports Server (NTRS)

Stanitz, John D

1953-01-01

A general method of design is developed for two-dimensional unbranched channels with prescribed velocities as a function of arc length along the channel walls. The method is developed for both compressible and incompressible, irrotational, nonviscous flow and applies to the design of elbows, diffusers, nozzles, and so forth. In part I solutions are obtained by relaxation methods; in part II solutions are obtained by a Green's function. Five numerical examples are given in part I including three elbow designs with the same prescribed velocity as a function of arc length along the channel walls but with incompressible, linearized compressible, and compressible flow. One numerical example is presented in part II for an accelerating elbow with linearized compressible flow, and the time required for the solution by a Green's function in part II was considerably less than the time required for the same solution by relaxation methods in part I.

Chemometric methods for the simultaneous determination of some water-soluble vitamins.

PubMed

Mohamed, Abdel-Maaboud I; Mohamed, Horria A; Mohamed, Niveen A; El-Zahery, Marwa R

2011-01-01

Two spectrophotometric methods, derivative and multivariate methods, were applied for the determination of binary, ternary, and quaternary mixtures of the water-soluble vitamins thiamine HCI (I), pyridoxine HCI (II), riboflavin (III), and cyanocobalamin (IV). The first method is divided into first derivative and first derivative of ratio spectra methods, and the second into classical least squares and principal components regression methods. Both methods are based on spectrophotometric measurements of the studied vitamins in 0.1 M HCl solution in the range of 200-500 nm for all components. The linear calibration curves were obtained from 2.5-90 microg/mL, and the correlation coefficients ranged from 0.9991 to 0.9999. These methods were applied for the analysis of the following mixtures: (I) and (II); (I), (II), and (III); (I), (II), and (IV); and (I), (II), (III), and (IV). The described methods were successfully applied for the determination of vitamin combinations in synthetic mixtures and dosage forms from different manufacturers. The recovery ranged from 96.1 +/- 1.2 to 101.2 +/- 1.0% for derivative methods and 97.0 +/- 0.5 to 101.9 +/- 1.3% for multivariate methods. The results of the developed methods were compared with those of reported methods, and gave good accuracy and precision.

Anti-aggregation-based spectrometric detection of Hg(II) at physiological pH using gold nanorods.

PubMed

Rajeshwari, A; Karthiga, D; Chandrasekaran, Natarajan; Mukherjee, Amitava

2016-10-01

An efficient detection method for Hg (II) ions at physiological pH (pH7.4) was developed using tween 20-modified gold nanorods (NRs) in the presence of dithiothreitol (DTT). Thiol groups (-SH) at the end of DTT have a higher affinity towards gold atoms, and they can covalently interact with gold NRs and leads to their aggregation. The addition of Hg(II) ions prevents the aggregation of gold NRs due to the covalent bond formation between the -SH group of DTT and Hg(II) ions in the buffer system. The changes in the longitudinal surface plasmon resonance peak of gold NRs were characterized using a UV-visible spectrophotometer. The absorption intensity peak of gold NRs at 679nm was observed to reduce after interaction with DTT, and the absorption intensity was noted to increase by increasing the concentration of Hg(II) ions. The TEM analysis confirms the morphological changes of gold NRs before and after addition of Hg(II) ions in the presence of DTT. Further, the aggregation and disaggregation of gold NRs were confirmed by particle size and zeta potential analysis. The developed method shows an excellent linearity (y=0.001x+0.794) for the graph plotted between the absorption ratio and Hg(II) concentration (1 to 100pM) under the optimized conditions. The limit of detection was noted to be 0.42pM in the buffer system. The developed method was tested in simulated body fluid, and it was found to have a good recovery rate. Copyright © 2016 Elsevier B.V. All rights reserved.

Implementing the UCSD PASCAL system on the MODCOMP computer. [deep space network

NASA Technical Reports Server (NTRS)

Wolfe, T.

1980-01-01

The implementation of an interactive software development system (UCSD PASCAL) on the MODCOMP computer is discussed. The development of an interpreter for the MODCOMP II and the MODCOMP IV computers, written in MODCOMP II assembly language, is described. The complete Pascal programming system was run successfully on a MODCOMP II and MODCOMP IV under both the MAX II/III and MAX IV operating systems. The source code for an 8080 microcomputer version of the interpreter was used as the design for the MODCOMP interpreter. A mapping of the functions within the 8080 interpreter into MODCOMP II assembly language was the method used to code the interpreter.

Development of a benchtop baking method for chemically leavened crackers. II. Validation of the method

USDA-ARS?s Scientific Manuscript database

A benchtop baking method has been developed to predict the contribution of gluten functionality to overall flour performance for chemically leavened crackers. Using a diagnostic formula and procedure, dough rheology was analyzed to evaluate the extent of gluten development during mixing and machinin...

[Comparative data regarding two HPLC methods for determination of isoniazid].

PubMed

Gârbuleţ, Daniela; Spac, A F; Dorneanu, V

2009-01-01

For the determination of isoniazide (isonicotinic acid hydrazide - HIN) two different HPLC methods were developed and validated. Both experiments were performed using a Waters 2695 liquid chromatograph and a UV - Waters 2489 detector. The first method (I) used a Nucleosil 100-10 C18 column (250 x 4.6 mm), a mobile phase formed by a mixture of acetonitrile/10(-2) M oxalic acid (80/20) and a flow of 1.5 mL/ min; detection was done at 230 nm. The second method (II) used a Luna 100-5 C18 column (250 x 4.6 mm), a mobile phase formed by a mixture of methanol/acetate buffer, pH = 5.0 (20/ 80), a flow of 1 mL/min; detection was done at 270 nm. Both methods were validated, the correlation coefficients were 0.9998 (I) and 0.9999 (II), the detection limits were 0.6 microg/mL (I) and 0.055 microg/mL (II), the quantitation limits were 1.9 microg/mL (I) and 0.2 microg/ mL (II). There were also studied: the system precision (RSD = 0.1692% (I) and 0.2000% (II)), the method precision (RSD = 1.1844% (I) and 0.6170% (II)) and the intermediate precision (RSD = 1.8058% (I) and 0.5970% (II)). The accuracy was good, the calculated recoveries were 102.66% (I) and 101.36 (II). Both validated methods were applied for HIN determination from tablets with good and comparable results.

Native State Mass Spectrometry, Surface Plasmon Resonance, and X-ray Crystallography Correlate Strongly as a Fragment Screening Combination.

PubMed

Woods, Lucy A; Dolezal, Olan; Ren, Bin; Ryan, John H; Peat, Thomas S; Poulsen, Sally-Ann

2016-03-10

Fragment-based drug discovery (FBDD) is contingent on the development of analytical methods to identify weak protein-fragment noncovalent interactions. Herein we have combined an underutilized fragment screening method, native state mass spectrometry, together with two proven and popular fragment screening methods, surface plasmon resonance and X-ray crystallography, in a fragment screening campaign against human carbonic anhydrase II (CA II). In an initial fragment screen against a 720-member fragment library (the "CSIRO Fragment Library") seven CA II binding fragments, including a selection of nonclassical CA II binding chemotypes, were identified. A further 70 compounds that comprised the initial hit chemotypes were subsequently sourced from the full CSIRO compound collection and screened. The fragment results were extremely well correlated across the three methods. Our findings demonstrate that there is a tremendous opportunity to apply native state mass spectrometry as a complementary fragment screening method to accelerate drug discovery.

Erosion control study : final report : Part II : roadside channels.

DOT National Transportation Integrated Search

1971-04-01

The objective of the study were: : 1) To evaluate present methods and develop new methods for establishing a permanent vegetative cover. : 2) To develop erosion control practices for existing highway drains and ditches. : 3) To develop highway bank s...

Development and Validation of a Measure of Interpersonal Strengths: The Inventory of Interpersonal Strengths

ERIC Educational Resources Information Center

Hatcher, Robert L.; Rogers, Daniel T.

2009-01-01

An Inventory of Interpersonal Strengths (IIS) was developed and validated in a series of large college student samples. Based on interpersonal theory and associated methods, the IIS was designed to assess positive characteristics representing the full range of interpersonal domains, including those generally thought to have negative qualities…

Developing planetary protection technology- microbial diversity of the Mars Orbiter Odyssey and the spacecraft assembly and encapsulation facility II

NASA Technical Reports Server (NTRS)

Duc, M. La; Chen, F.; Kern, R.; Koukol, R.; Baker, A.; Venkateswaran, K.

2001-01-01

A study in which several surface samples, retrieved from both the Mars Odyssey Spacecraft and the Kennedy Space Center (KSC) Spacecraft Assembly and Encapsulation Facility II (SAEF-II), were prcesed and evaluated by both molecular and traditional culture-based methods for the microbial diversity.

Preschool Racial Attitude Measure II (PRAM II): General Information and Manual of Directions.

ERIC Educational Resources Information Center

Williams, John E.

The Preschool Racial Attitude Measure (PRAM) has been developed to provide a method for assessing the attitudes of pre-literature children toward Caucasian and Black persons. This manual provides information concerning the administration and scoring of the revised procedure--PRAM II. The revision entailed doubling the length, improving the…

Synthesis and application of surface-imprinted activated carbon sorbent for solid-phase extraction and determination of copper (II)

NASA Astrophysics Data System (ADS)

Li, Zhenhua; Li, Jingwen; Wang, Yanbin; Wei, Yajun

2014-01-01

A new Cu(II)-imprinted amino-functionalized activated carbon sorbent was prepared by a surface imprinting technique for selective solid-phase extraction (SPE) of Cu(II) prior to its determination by inductively coupled plasma atomic emission spectrometry (ICP-AES). Experimental conditions for effective adsorption of Cu(II) were optimized with respect to different experimental parameters using static and dynamic procedures in detail. Compared with non-imprinted sorbent, the ion-imprinted sorbent had higher selectivity and adsorption capacity for Cu(II). The maximum static adsorption capacity of the ion-imprinted and non-imprinted sorbent for Cu(II) was 26.71 and 6.86 mg g-1, respectively. The relatively selectivity factor values (αr) of Cu(II)/Zn(II), Cu(II)/Ni(II), Cu(II)/Co(II) and Cu(II)/Pb(II) were 166.16, 50.77, 72.26 and 175.77, respectively, which were greater than 1. Complete elution of the adsorbed Cu(II) from Cu(II)-imprinted sorbent was carried out using 2 mL of 0.1 mol L-1 EDTA solution. The relative standard deviation of the method was 2.4% for eleven replicate determinations. The method was validated for the analysis by two certified reference materials (GBW 08301, GBW 08303), the results obtained is in good agreement with standard values. The developed method was also successfully applied to the determination of trace copper in natural water samples with satisfactory results.

Synthesis and application of surface-imprinted activated carbon sorbent for solid-phase extraction and determination of copper (II).

PubMed

Li, Zhenhua; Li, Jingwen; Wang, Yanbin; Wei, Yajun

2014-01-03

A new Cu(II)-imprinted amino-functionalized activated carbon sorbent was prepared by a surface imprinting technique for selective solid-phase extraction (SPE) of Cu(II) prior to its determination by inductively coupled plasma atomic emission spectrometry (ICP-AES). Experimental conditions for effective adsorption of Cu(II) were optimized with respect to different experimental parameters using static and dynamic procedures in detail. Compared with non-imprinted sorbent, the ion-imprinted sorbent had higher selectivity and adsorption capacity for Cu(II). The maximum static adsorption capacity of the ion-imprinted and non-imprinted sorbent for Cu(II) was 26.71 and 6.86 mg g(-1), respectively. The relatively selectivity factor values (αr) of Cu(II)/Zn(II), Cu(II)/Ni(II), Cu(II)/Co(II) and Cu(II)/Pb(II) were 166.16, 50.77, 72.26 and 175.77, respectively, which were greater than 1. Complete elution of the adsorbed Cu(II) from Cu(II)-imprinted sorbent was carried out using 2 mL of 0.1 mol L(-1) EDTA solution. The relative standard deviation of the method was 2.4% for eleven replicate determinations. The method was validated for the analysis by two certified reference materials (GBW 08301, GBW 08303), the results obtained is in good agreement with standard values. The developed method was also successfully applied to the determination of trace copper in natural water samples with satisfactory results. Copyright © 2013 Elsevier B.V. All rights reserved.

Colorimetric Detection of Mercury(II) Ion in Aqueous Solution Using Silver Nanoparticles.

PubMed

Firdaus, M Lutfi; Fitriani, Ikka; Wyantuti, Santhy; Hartati, Yeni W; Khaydarov, Renat; McAlister, Jason A; Obata, Hajime; Gamo, Toshitaka

2017-01-01

Novel green-chemistry synthesis of silver nanoparticles (AgNPs) is introduced as a low-cost, rapid and easy-to-use analytical method for mercury ion detection. Aqueous fruit extract of water apple (Syzygium aqueum) was used for the first time as bioreductant to synthesize stable AgNPs. The prepared AgNPs have a yellowish-brown color with a surface plasmon resonance peak at 420 nm. The addition of Hg(II) ions then changes the AgNPs color to colorless. The color change was in proportion to the concentration of Hg(II) ions. The presence of other metal ions in the system was also evaluated. The proposed method shows good selectivity and sensitivity towards Hg(II) ions. Using UV-visible spectrophotometry, the detection limit of the developed method was 8.5 × 10 -7 M. The proposed method has been successfully applied for determination of Hg(II) ions in tap and lake water samples with precision better than 5%.

High-sensitivity determination of Zn(II) and Cu(II) in vitro by fluorescence polarization

NASA Astrophysics Data System (ADS)

Thompson, Richard B.; Maliwal, Badri P.; Feliccia, Vincent; Fierke, Carol A.

1998-04-01

Recent work has suggested that free Cu(II) may play a role in syndromes such as Crohn's and Wilson's diseases, as well as being a pollutant toxic at low levels to shellfish and sheep. Similarly, Zn(II) has been implicated in some neural damage in the brain resulting from epilepsy and ischemia. Several high sensitivity methods exist for determining these ions in solution, including GFAAS, ICP-MS, ICP-ES, and electrochemical techniques. However, these techniques are generally slow and costly, require pretreatment of the sample, require complex instruments and skilled personnel, and are incapable of imaging at the cellular and subcellular level. To address these shortcomings we developed fluorescence polarization (anisotropy) biosensing methods for these ions which are very sensitivity, highly selective, require simple instrumentation and little pretreatment, and are inexpensive. Thus free Cu(II) or Zn(II) can be determined at picomolar levels by changes in fluorescence polarization, lifetime, or wavelength ratio using these methods; these techniques may be adapted to microscopy.

Sixth Grade Students' Development of Historical Perspective: World War II and the Atomic Bombing of Hiroshima and Nagasaki.

ERIC Educational Resources Information Center

Ogawa, Masato

This study investigated how the use of various teaching methods influenced perspective taking skills of sixth grade middle school students during a unit of instruction on World War II. Three questions directed the study: (1) What do students know about World War II prior to a unit of study on World War II; (2) What do students know about World War…

Simultaneous Stripping Detection of Pb(II), Cd(II) and Zn(II) Using a Bimetallic Hg-Bi/Single-Walled Carbon Nanotubes Composite Electrode

PubMed Central

Ouyang, Ruizhuo; Zhu, Zhenqian; Tatum, Clarissa E.; Chambers, James Q.; Xue, Zi-Ling

2011-01-01

A new, sensitive platform for the simultaneous electrochemical assay of Zn(II), Cd(II) and Pb(II) in aqueous solution has been developed. The platform is based on a new bimetallic Hg-Bi/single-walled carbon nanotubes (SWNTs) composite modified glassy carbon electrode (GCE), demonstrating remarkably improved performance for the anodic stripping assay of Zn(II), Cd(II) and Pb(II). The synergistic effect of Hg and Bi as well as the enlarged, activated surface and good electrical conductivity of SWNTs on GCE contribute to the enhanced activity of the proposed electrode. The analytical curves for Zn(II), Cd(II) an Pb(II) cover two linear ranges varying from 0.5 to 11 μg L-1 and 10 to 130 μg L-1 with correlation coefficients higher than 0.992. The limits of detection for Zn(II), Cd(II) are lower than 2 μg L-1 (S/N = 3). For Pb(II), moreover, there is another lower, linear range from 5 to 1100 ng L-1 with a coefficient of 0.987 and a detection limit of 0.12 ng L-1. By using the standard addition method, Zn(II), Cd(II) and Pb(II) ions in river samples were successfully determined. These results suggest that the proposed method can be applied as a simple, efficient alternative for the simultaneous monitoring of heavy metals in water samples. In addition, this method demonstrates the powerful application of carbon nanotubes in electrochemical analysis of heavy metals. PMID:21660117

Formic Acid: Development of an Analytical Method and Use as Process Indicator in Anaerobic Systems

DTIC Science & Technology

1992-03-01

distilled to remove compounds such as cinnamic , glycolic and levulinic acids which can be oxidized to formic acid by ceric sulfate, thus interfering...I AD-A250 668 D0 ,I I I 111 Wl’i ill EDT|CS ELECTE MAY 27 1992 I C I FORMIC ACID : DEVELCPMENT OF AN ANALYTICAL METHOD AND USE AS A PROCESS INDICATOR...OF TECHNOLOGY A UNIT OF THE UNIVERSITY SYSTEM OF GEORGIA SCHOOL OF CIVIL ENGINEERING ATLANTA, GEORGIA 30332 iIi ii FORMIC ACID : DEVELOPMENT OF AN

Can Alberta infant motor scale and milani comparetti motor development screening test be rapid alternatives to bayley scales of infant development-II at high-risk infants

PubMed Central

Yıldırım, Zeynep Hoşbay; Aydınlı, Nur; Ekici, Barış; Tatlı, Burak; Çalişkan, Mine

2012-01-01

Purpose: The main object of the present study is to assess neuromotor development of high-risk infants by using three tests, and to determine inter-test concordance and the feasibility of these tests. Materials and Methods: One-hundred and nine patients aged between 0 and 6 months and identified as “high-risk infant” according to the Kliegman's criteria were enrolled to the study. Three different tests were used to assess neuromotor development of the patients: Bayley scales of infant development-II (BSID-II), Alberta infant motor scale (AIMS), and Milani Comparetti Motor Development Screening Test (MCMDST). Results: Correlation analysis was performed between pure scores of BSID-II motor scale and total scores of AIMS. These two tests were highly correlated (r:0.92). Moderate concordance was found between BSID-II and AIMS (k:0.35). Slight concordance was found between BSID-II and MCMDST; and the concordance was slight again for AIMS and MCMDST (k:0.11 and k:0.16, respectively) too. Conclusion: AIMS has a high correlation and consistency with BSID-II and can be used with routine neurological examination as it is based on observations, has few items, and requires less time to complete. PMID:22919192

A method of the up or down layer development of class II oil reservoirs

NASA Astrophysics Data System (ADS)

Wang, Fulin; Zhao, Yunfei; Fang, Yanjun; Yang, Tao; Gui, Dongxu; Wang, Gang; Feng, Chengcheng

2018-06-01

During the 13th five-year period, class II reservoirs of DaQing Oilfield first layer series development will be fully completed, secondary up or down layer development is facing new well drilling or the use of old we ll pattern network method chosen, need to determine development mode of oil block. In this paper, the system economy model is established, the up and down oil layer of the block is considered as one system, and through the comparison of the two models that new well drilling or the use of old well pattern, we can determine the development mode of the block. And take b1ddd block as an example, determine the block need to use what method to develop in different oil prices. Result show when the oil price is 40/bbl, using exiting well to production, when oil price is 70/bbl., using new drilling development model. The method to fill the theory and methodology on selection about reservoir development mode, can provide technical support for DaQing Oilfield the 14th five-year planning and long-term planning.

Fluorometric method for inorganic pyrophosphatase activity detection and inhibitor screening based on click chemistry.

PubMed

Xu, Kefeng; Chen, Zhonghui; Zhou, Ling; Zheng, Ou; Wu, Xiaoping; Guo, Longhua; Qiu, Bin; Lin, Zhenyu; Chen, Guonan

2015-01-06

A fluorometric method for pyrophosphatase (PPase) activity detection was developed based on click chemistry. Cu(II) can coordinate with pyrophosphate (PPi), the addition of pyrophosphatase (PPase) into the above system can destroy the coordinate compound because PPase catalyzes the hydrolysis of PPi into inorganic phosphate and produces free Cu(II), and free Cu(II) can be reduced by sodium ascorbate (SA) to form Cu(I), which in turn initiates the ligating reaction between nonfluorescent 3-azidocoumarins and terminal alkynes to produce a highly fluorescent triazole complex, based on which, a simple and sensitive turn on fluorometric method for PPase can be developed. The fluorescence intensity of the system has a linear relationship with the logarithm of the PPase concentration in the range of 0.5 and 10 mU with a detection limit down to 0.2 mU (S/N = 3). This method is cost-effective and convenient without any labels or complicated operations. The proposed system was applied to screen the potential PPase inhibitor with high efficiency. The proposed method can be applied to diagnosis of PPase-related diseases.

[Determinants of strategic management of a health center].

PubMed

Huard, Pierre; Schaller, Philippe

2014-01-01

The article highlights the value of a strategic approach for the development of a primary care health centre. The method is adapted from corporate strategy: (i) analysis of the situation of the health centre and the obstacles to its development. (ii) selection of relations on which the strategy can be developed. (iii) elaboration of a system of interventions to create a cumulative development process. (iv) Illustration of the method by application to a case. The example illustrates the principles and method and highlights the importance of interpretations and choices in elaboration of a strategy, which is therefore always a unique construction. The strategic approach provides a framework that (i) provides a subject of discussion and negotiation between members of the health centre, (ii) strengthens the consistency of structural decisions, (iii) helps the health centre to overcome obstacles and initiate a development process.

A newly validated and characterized spectrophotometric method for determination of a three water pollutants metal ions

NASA Astrophysics Data System (ADS)

Mohamed, Marwa E.; Frag, Eman Y. Z.; Mohamed, Mona A.

2018-01-01

A simple, fast and accurate spectrophotometric method had been developed to determine lead (II), chromium (III) and barium (II) ions in pure forms and in spiked water samples using thoron (THO) as a reagent forming colored complexes. It was found that the formed complexes absorbed maximally at 539, 540 and 538 nm for Pb(II)-THO, Cr(III)-THO and Ba(II)-THO complexes, respectively. The optimum experimental conditions for these complexes had been studied carefully. Beer's law was obeyed in the range 1-35, 1-70, and 1-45 μg mL- 1 for Pb (II), Cr(III) and Ba(II) ions with THO reagent, respectively. Different parameters such as linearity, selectivity, recovery, limits of quantification and detection, precision and accuracy were also evaluated in order to validate the proposed method. The results showed that, THO was effective in simultaneous determination of Pb(II), Cr(III) and Ba(III) ions in pure forms and in spiked water samples. Also, the results of the proposed method were compared with that obtained from atomic absorption spectrometry. The isolated solid complexes had been characterized using elemental analysis, X-ray powder diffraction (XRD), IR, mass spectrometry and TD-DFT calculations. Their biological activities were investigated against different types of bacteria and fungi organisms.

Application of Colorimetric Solid Phase Extraction (C-SPE) to Monitoring Nickel(II) and Lead(II) in Spacecraft Water Supplies

NASA Technical Reports Server (NTRS)

Diaz, Neil C.; Gazda, Daniel B.; Fritz, James S.; Porter, Marc D.; Rutz, Jeff; Mudgett, Paul; Schultz, John

2004-01-01

Archived water samples collected on the International Space Station (ISS) and returned to Earth for analysis have, in a few instances, contained trace levels of heavy metals. Building on our previous advances using Colorimetric Solid Phase Extraction (C-SPE) as a biocide monitoring technique, we are devising methods for the low level monitoring of nickel(II), lead(II) and other heavy metals. C-SPE is a sorption-spectrophotometric platform based on the extraction of analytes onto a membrane impregnated with a colorimetric reagent that are then quantified on the surface of the membrane using a diffuse reflectance spectrophotometer. Along these lines, we have determined nickel(II) via complexation with dimethylglyoxime (DMG) and begun to examine the analysis of lead(II) by its reaction with 2,5- dimercapto-1,3,4-thiadiazole (DMTD) and 4-(2- pyridylazo)-resorcinol (PAR). These developments are also extending a new variant of C-SPE in which immobilized reagents are being incorporated into this methodology in order to optimize sample reaction conditions and to introduce the colorimetric reagent. This paper describes the status of our development of these two new methods.

A convenient method for determination of malathion based on the resonance Rayleigh scattering enhancement

NASA Astrophysics Data System (ADS)

Wu, Huan; Zhao, Yanmei; Tan, Xuanping; Huang, Yunmei; Yuan, Haiyan; Yang, Jidong

2017-09-01

A convenient method for determination of malathion (Mala) based on resonance Rayleigh scattering (RRS) enhancement of L-Tryptophan (L-Try)-Pd(II)-Mala system was proposed in this paper. The interaction between L-Try, Pd(II) and malathion in the system was investigated by fluorescence, RRS and UV-Vis absorption spectroscopy. In the optimum conditions, the RRS intensity of L-Try-Pd(II)-Mala system had a remarkable enhancement because the hydrolysis products of malathion would interact with Pd(II) and L-Try each other formed new complexes, which enhanced intensity was directly proportional to the malathion concentration within a certain range. Based on the RRS enhancement of L-Try-Pd(II) system by Mala, a novel, convenient and specific method for Mala determination was developed. To our knowledge, the method is the first RRS method for determination of Mala was reported. The detection limit for Mala was 6.7 ng/mL and the quantitative determination range was 0.06-0.6 μg/mL. The influence of coexisting substances on RRS was also investigated, and the RRS method exhibited good anti-interference ability. The new analytical method has been applied to determine of malathion in real samples with satisfactory results.

Magnetic sensor for nondestructive evaluation of deteriorated prestressing strand : phase II.

DOT National Transportation Integrated Search

2011-08-01

This report gives an account of the execution and achievements in Phase II of the project completed through August 2011. The main objective of this project is to advance the practical development of a nondestructive testing and evaluation method usin...

NetMHCIIpan-2.0 - Improved pan-specific HLA-DR predictions using a novel concurrent alignment and weight optimization training procedure.

PubMed

Nielsen, Morten; Justesen, Sune; Lund, Ole; Lundegaard, Claus; Buus, Søren

2010-11-13

Binding of peptides to Major Histocompatibility class II (MHC-II) molecules play a central role in governing responses of the adaptive immune system. MHC-II molecules sample peptides from the extracellular space allowing the immune system to detect the presence of foreign microbes from this compartment. Predicting which peptides bind to an MHC-II molecule is therefore of pivotal importance for understanding the immune response and its effect on host-pathogen interactions. The experimental cost associated with characterizing the binding motif of an MHC-II molecule is significant and large efforts have therefore been placed in developing accurate computer methods capable of predicting this binding event. Prediction of peptide binding to MHC-II is complicated by the open binding cleft of the MHC-II molecule, allowing binding of peptides extending out of the binding groove. Moreover, the genes encoding the MHC molecules are immensely diverse leading to a large set of different MHC molecules each potentially binding a unique set of peptides. Characterizing each MHC-II molecule using peptide-screening binding assays is hence not a viable option. Here, we present an MHC-II binding prediction algorithm aiming at dealing with these challenges. The method is a pan-specific version of the earlier published allele-specific NN-align algorithm and does not require any pre-alignment of the input data. This allows the method to benefit also from information from alleles covered by limited binding data. The method is evaluated on a large and diverse set of benchmark data, and is shown to significantly out-perform state-of-the-art MHC-II prediction methods. In particular, the method is found to boost the performance for alleles characterized by limited binding data where conventional allele-specific methods tend to achieve poor prediction accuracy. The method thus shows great potential for efficient boosting the accuracy of MHC-II binding prediction, as accurate predictions can be obtained for novel alleles at highly reduced experimental costs. Pan-specific binding predictions can be obtained for all alleles with know protein sequence and the method can benefit by including data in the training from alleles even where only few binders are known. The method and benchmark data are available at http://www.cbs.dtu.dk/services/NetMHCIIpan-2.0.

1-(2-Formamidoethyl)-3-phenylurea functionalized activated carbon for selective solid-phase extraction and preconcentration of metal ions.

PubMed

Tu, Zhifeng; He, Qun; Chang, Xijun; Hu, Zheng; Gao, Ru; Zhang, Lina; Li, Zhenhua

2009-09-07

A novel method that utilizes 1-(2-formamidoethyl)-3-phenylurea-modified activated carbon (AC-1-(2-formamidoethyl)-3-phenylurea) as a solid-phase extractant has been developed for simultaneous preconcentration of trace Cr(III), Cu(II), Fe(III) and Pb(II) prior to the measurement by inductively coupled plasma atomic emission spectrometry (ICP-AES). Experimental conditions for effective adsorption of trace levels of Cr(III), Cu(II), Fe(III) and Pb(II) were optimized using batch and column procedures in detail. The optimum pH value for the separation of metal ions simultaneously on the new sorbent was 4. And the adsorbed metal ions could be completely eluted by using 2.0 mL 2.0 mol L(-1) HCl solution. Common coexisting ions did not interfere with the separation and determination of target metal ions. The maximum static adsorption capacity of the sorbent at optimum conditions was found to be 39.8, 39.9, 77.8 and 17.3 mg g(-1) for Cr(III), Cu(II), Fe(III) and Pb(II), respectively. The detection limits of the method were found to be 0.15, 0.41, 0.27 and 0.36 ng mL(-1) for Cr(III), Cu(II), Fe(III) and Pb(II), respectively. The relative standard deviation (RSD) of the method was lower than 4.0% (n=8). The method was successfully applied for the preconcentration of trace Cr(III), Cu(II), Fe(III) and Pb(II) in natural and certified samples with satisfactory results.

QUANTIFICATION OF TRANSGENIC PLANT MARKER GENE PERSISTENCE IN THE FIELD

EPA Science Inventory

Methods were developed to monitor persistence of genomic DNA in decaying plants in the field. As a model, we used recombinant neomycin phosphotransferase II (rNPT-II) marker genes present in genetically engineered plants. Polymerase chain reaction (PCR) primers were designed, com...

High-sensitivity assay for Hg (II) and Ag (I) ion detection: A new class of droplet digital PCR logic gates for an intelligent DNA calculator.

PubMed

Cheng, Nan; Zhu, Pengyu; Xu, Yuancong; Huang, Kunlun; Luo, Yunbo; Yang, Zhansen; Xu, Wentao

2016-10-15

The first example of droplet digital PCR logic gates ("YES", "OR" and "AND") for Hg (II) and Ag (I) ion detection has been constructed based on two amplification events triggered by a metal-ion-mediated base mispairing (T-Hg(II)-T and C-Ag(I)-C). In this work, Hg(II) and Ag(I) were used as the input, and the "true" hierarchical colors or "false" green were the output. Through accurate molecular recognition and high sensitivity amplification, positive droplets were generated by droplet digital PCR and viewed as the basis of hierarchical digital signals. Based on this principle, YES gate for Hg(II) (or Ag(I)) detection, OR gate for Hg(II) or Ag(I) detection and AND gate for Hg(II) and Ag(I) detection were developed, and their sensitively and selectivity were reported. The results indicate that the ddPCR logic system developed based on the different indicators for Hg(II) and Ag(I) ions provides a useful strategy for developing advanced detection methods, which are promising for multiplex metal ion analysis and intelligent DNA calculator design applications. Copyright © 2016 Elsevier B.V. All rights reserved.

A novel method for simultaneous Enterococcus species identification/typing and van genotyping by high resolution melt analysis.

PubMed

Gurtler, Volker; Grando, Danilla; Mayall, Barrie C; Wang, Jenny; Ghaly-Derias, Shahbano

2012-09-01

In order to develop a typing and identification method for van gene containing Enterococcus faecium, two multiplex PCR reactions were developed for use in HRM-PCR (High Resolution Melt-PCR): (i) vanA, vanB, vanC, vanC23 to detect van genes from different Enterococcus species; (ii) ISR (intergenic spacer region between the 16S and 23S rRNA genes) to detect all Enterococcus species and obtain species and isolate specific HRM curves. To test and validate the method three groups of isolates were tested: (i) 1672 Enterococcus species isolates from January 2009 to December 2009; (ii) 71 isolates previously identified and typed by PFGE (pulsed-field gel electrophoresis) and MLST (multi-locus sequence typing); and (iii) 18 of the isolates from (i) for which ISR sequencing was done. As well as successfully identifying 2 common genotypes by HRM from the Austin Hospital clinical isolates, this study analysed the sequences of all the vanB genes deposited in GenBank and developed a numerical classification scheme for the standardised naming of these vanB genotypes. The identification of Enterococcus faecalis from E. faecium was reliable and stable using ISR PCR. The typing of E. faecium by ISR PCR: (i) detected two variable peaks corresponding to different copy numbers of insertion sequences I and II corresponding to peak I and II respectively; (ii) produced 7 melt profiles for E. faecium with variable copy numbers of sequences I and II; (iii) demonstrated stability and instability of peak heights with equal frequency within the patient sample (36.4±4.5 days and 38.6±5.8 days respectively for 192 patients); (iv) detected ISR-HRM types with as much discrimination as PFGE and more than MLST; and (v) detected ISR-HRM types that differentiated some isolates that were identical by PFGE and MLST. In conjunction with the rapid and accurate van genotyping method described here, this ISR-HRM typing and identification method can be used as a stable identification and typing method with predictable instability based on recombination and concerted evolution of the rrn operon that will complement existing typing methods. Crown Copyright © 2012. Published by Elsevier B.V. All rights reserved.

Copper Ion Detection in Drinking Water via a Fabric Nanocomposite Sensor

NASA Astrophysics Data System (ADS)

Yu, Guoqiang

Excessive Cu(II) ions in drinking water are always a big threat to people's health. In this work, we developed a flexible amperometric sensor by a simple dip-coating method, which was able to rapidly, sensitively, and selectively detect the Cu(II) ions in the range of 0.65 to 39 ppm in real time. The prepared Cu(II) sensor consisted of three layers that were electrospun nylon-6 nanofibers, multiwalled carbon nanotubes (MWCNTs), and 2,2':5',2''-terthiophene molecules, respectively. When a voltage was applied to the Cu(II) sensor, the current was obviously impeded in the presence of Cu(II) ions. Interfering metal ions, including Cd(II), Fe(II), Pb(II), Hg(II), and Ag(I) ions, had almost no influence on the responsiveness of the Cu(II) sensor.

Sensitive spectrophotometric determination of Co(II) using dispersive liquid-liquid micro-extraction method in soil samples.

PubMed

Hasanpour, Foroozan; Hadadzadeh, Hassan; Taei, Masoumeh; Nekouei, Mohsen; Mozafari, Elmira

2016-05-01

Analytical performance of conventional spectrophotometer was developed by coupling of effective dispersive liquid-liquid micro-extraction method with spectrophotometric determination for ultra-trace determination of cobalt. The method was based on the formation of Co(II)-alpha-benzoin oxime complex and its extraction using a dispersive liquid-liquid micro-extraction technique. During the present work, several important variables such as pH, ligand concentration, amount and type of dispersive, and extracting solvent were optimized. It was found that the crucial factor for the Co(II)-alpha benzoin oxime complex formation is the pH of the alkaline alcoholic medium. Under the optimized condition, the calibration graph was linear in the ranges of 1.0-110 μg L(-1) with the detection limit (S/N = 3) of 0.5 μg L(-1). The preconcentration operation of 25 mL of sample gave enhancement factor of 75. The proposed method was applied for determination of Co(II) in soil samples.

Detection of lead(II) ions with a DNAzyme and isothermal strand displacement signal amplification.

PubMed

Li, Wenying; Yang, Yue; Chen, Jian; Zhang, Qingfeng; Wang, Yan; Wang, Fangyuan; Yu, Cong

2014-03-15

A DNAzyme based method for the sensitive and selective quantification of lead(II) ions has been developed. A DNAzyme that requires Pb(2+) for activation was selected. An RNA containing DNA substrate was cleaved by the DNAzyme in the presence of Pb(2+). The 2',3'-cyclic phosphate of the cleaved 5'-part of the substrate was efficiently removed by Exonuclease III. The remaining part of the single stranded DNA (9 or 13 base long) was subsequently used as the primer for the strand displacement amplification reaction (SDAR). The method is highly sensitive, 200 pM lead(II) could be easily detected. A number of interference ions were tested, and the sensor showed good selectivity. Underground water samples were also tested, which demonstrated the feasibility of the current approach for real sample applications. It is feasible that our method could be used for DNAzyme or aptazyme based new sensing method developments for the quantification of other target analytes with high sensitivity and selectivity. © 2013 Elsevier B.V. All rights reserved.

An ultrasensitive chemiluminescence immunoassay of chloramphenicol based on gold nanoparticles and magnetic beads.

PubMed

Tao, Xiaoqi; Jiang, Haiyang; Yu, Xuezhi; Zhu, Jinghui; Wang, Xia; Wang, Zhanhui; Niu, Lanlan; Wu, Xiaoping; Shen, Jianzhong

2013-05-01

A competitive, direct, chemiluminescent immunoassay based on a magnetic beads (MBs) separation and gold nanoparticles (AuNPs) labelling technique to detect chloramphenicol (CAP) has been developed. Horseradish peroxidase (HRP)-labelled anti-CAP monoclonal antibody conjugated with AuNPs and antigen-immobilized MBs were prepared. After optimization parameters of immunocomplex MBs, the IC50 values of chemiluminescence magnetic nanoparticles immunoassay (CL-MBs-nano-immunoassay) were 0.017 µg L(-1) for extract method I and 0.17 µg L(-1) for extract method II. The immunoassay with two extract methods was applied to detect CAP in milk. Comparison of these two extract methods showed that extract method I was advantageous in better sensitivity, in which the sensitivity was 10 times compared to that of extract method II, while extract method II was superior in simple operation, suitable for high throughout screen. The recoveries were 86.7-98.0% (extract method I) and 80.0-103.0% (extract method II), and the coefficients of variation (CVs) were all <15%. The satisfactory recovery with both extract methods and high correlation with traditional ELISA kit in milk system confirmed that the immunomagnetic assay based on AuNPs exhibited promising potential in rapid field screening for trace CAP analysis. Copyright © 2013 John Wiley & Sons, Ltd.

Knowledge Workshop Development

DTIC Science & Technology

1976-01-30

priorities. The mechanism also seems to act as a buffer between developer and user, softening the negative aspects of user frustration while still...structure ’ programming methods. 4) Documentation: Effective documentation methods must be developed and used since undocumented programs are virtually...1-W.,U1..W1 . II I u KNOWLEDGE WORKSHOP DEVELOPMENT Douglas C. Engelbart Stanford Research Institute AD-A022 997 Prepared for: Rome

Regioselective 1,4- and 1,6-Conjugate Additions of Grignard Reagent-Derived Organozinc(II)ates to Polyconjugated Esters.

PubMed

Hatano, Manabu; Mizuno, Mai; Ishihara, Kazuaki

2016-09-16

Regioselective synthetic methods were developed for 1,4- and 1,6-conjugate additions of Grignard reagent-derived organozinc(II)ates to malonate-derived polyconjugated esters. By taking advantage of the tight ion-pair control of organozinc(II)ates, it was possible to switch between 1,4- and 1,6-conjugate additions by introducing a terminal ethoxy moiety in the conjugation.

A novel optical gating method for laser gated imaging

NASA Astrophysics Data System (ADS)

Ginat, Ran; Schneider, Ron; Zohar, Eyal; Nesher, Ofer

2013-06-01

For the past 15 years, Elbit Systems is developing time-resolved active laser-gated imaging (LGI) systems for various applications. Traditional LGI systems are based on high sensitive gated sensors, synchronized to pulsed laser sources. Elbit propriety multi-pulse per frame method, which is being implemented in LGI systems, improves significantly the imaging quality. A significant characteristic of the LGI is its ability to penetrate a disturbing media, such as rain, haze and some fog types. Current LGI systems are based on image intensifier (II) sensors, limiting the system in spectral response, image quality, reliability and cost. A novel propriety optical gating module was developed in Elbit, untying the dependency of LGI system on II. The optical gating module is not bounded to the radiance wavelength and positioned between the system optics and the sensor. This optical gating method supports the use of conventional solid state sensors. By selecting the appropriate solid state sensor, the new LGI systems can operate at any desired wavelength. In this paper we present the new gating method characteristics, performance and its advantages over the II gating method. The use of the gated imaging systems is described in a variety of applications, including results from latest field experiments.

Novel methods to estimate the enantiomeric ratio and the kinetic parameters of enantiospecific enzymatic reactions.

PubMed

Machado, G D.C.; Paiva, L M.C.; Pinto, G F.; Oestreicher, E G.

2001-03-08

1The Enantiomeric Ratio (E) of the enzyme, acting as specific catalysts in resolution of enantiomers, is an important parameter in the quantitative description of these chiral resolution processes. In the present work, two novel methods hereby called Method I and II, for estimating E and the kinetic parameters Km and Vm of enantiomers were developed. These methods are based upon initial rate (v) measurements using different concentrations of enantiomeric mixtures (C) with several molar fractions of the substrate (x). Both methods were tested using simulated "experimental data" and actual experimental data. Method I is easier to use than Method II but requires that one of the enantiomers is available in pure form. Method II, besides not requiring the enantiomers in pure form shown better results, as indicated by the magnitude of the standard errors of estimates. The theoretical predictions were experimentally confirmed by using the oxidation of 2-butanol and 2-pentanol catalyzed by Thermoanaerobium brockii alcohol dehydrogenase as reaction models. The parameters E, Km and Vm were estimated by Methods I and II with precision and were not significantly different from those obtained experimentally by direct estimation of E from the kinetic parameters of each enantiomer available in pure form.

An efficient, cost effective, sensing behaviour liquid-liquid extraction and spectrophotometric determination of copper(II) incorporated with 4-(4‧-chlorobenzylideneimino)-3-methyl-5-mercapto-1, 2, 4-triazole: Analysis of food samples, leafy vegetables, fertilizers and environmental samples

NASA Astrophysics Data System (ADS)

Barache, Umesh B.; Shaikh, Abdul B.; Lokhande, Tukaram N.; Kamble, Ganesh S.; Anuse, Mansing A.; Gaikwad, Shashikant H.

2018-01-01

The aim of the present work is to develop an efficient, simple and selective moreover cost-effective method for the extractive spectrophotometric determination of copper(II) by using the Schiff base 4-(4‧-chlorobenzylideneimino)-3-methyl-5-mercapto-1, 2, 4-triazole [CBIMMT]. This chromogenic reagent forms a yellow coloured complex with copper(II) in acetate buffer at pH 4.2. The copper(II) complex with ligand is instantly extracted into chloroform and shows a maximum absorbance at 414 nm which remains stable for > 48 h. The composition of extracted complex is found to be 1:2 [copper(II): reagent] which was ascertained using Job's method of continuous variation, mole ratio method and slope ratio method. Under optimal conditions, the copper(II) complex in chloroform adheres to Beer's law up to 17.5 μg mL- 1 of copper(II). The optimum concentration range obtained from Ringbom's plot is from 5 μg mL- 1 to 17.5 μg mL- 1. The molar absorptivity, Sandell's sensitivity and enrichment factor of the extracted copper(II) chelate are 0.33813 × 104 L mol- 1 cm- 1, 0.01996 μg cm- 2 and 2.49 respectively. In the extraction of copper(II), several affecting factors including the solution pH, ligand concentration, equilibrium time, effect of foreign ions are optimized. The interfering effects of various cations and anions were also studied and use of masking agents enhances the selectivity of the method. The chromogenic sulphur containing reagent, 4-(4‧-chlorobenzylideneimino)-3-methyl-5-mercapto-1, 2, 4-triazole has been synthesized in a single step with high purity and yield. The synthesized reagent has been successfully applied first time for determination of copper(II). The reagent forms stable chelate with copper(II) in buffer medium instantly and quantitatively extracted in chloroform within a minute. The method is successfully applied for the determination of copper(II) in various synthetic mixtures, complexes, fertilizers, environmental samples such as food samples, leafy vegetables, and water samples. The results are compared with those obtained with a reference procedure. Good agreement was attained. All the obtained results are indicative of a convenient, fast method for the extraction and quantification of micro levels of copper(II) from various environmental matrices without use of sophisticated instrumentation and procedure. The method showed a relative standard deviation of 0.42%.

An efficient, cost effective, sensing behaviour liquid-liquid extraction and spectrophotometric determination of copper(II) incorporated with 4-(4'-chlorobenzylideneimino)-3-methyl-5-mercapto-1, 2, 4-triazole: Analysis of food samples, leafy vegetables, fertilizers and environmental samples.

PubMed

Barache, Umesh B; Shaikh, Abdul B; Lokhande, Tukaram N; Kamble, Ganesh S; Anuse, Mansing A; Gaikwad, Shashikant H

2018-01-15

The aim of the present work is to develop an efficient, simple and selective moreover cost-effective method for the extractive spectrophotometric determination of copper(II) by using the Schiff base 4-(4'-chlorobenzylideneimino)-3-methyl-5-mercapto-1, 2, 4-triazole [CBIMMT]. This chromogenic reagent forms a yellow coloured complex with copper(II) in acetate buffer at pH4.2. The copper(II) complex with ligand is instantly extracted into chloroform and shows a maximum absorbance at 414nm which remains stable for >48h. The composition of extracted complex is found to be 1:2 [copper(II): reagent] which was ascertained using Job's method of continuous variation, mole ratio method and slope ratio method. Under optimal conditions, the copper(II) complex in chloroform adheres to Beer's law up to 17.5μgmL -1 of copper(II). The optimum concentration range obtained from Ringbom's plot is from 5μgmL -1 to 17.5μgmL -1 . The molar absorptivity, Sandell's sensitivity and enrichment factor of the extracted copper(II) chelate are 0.33813×10 4 Lmol -1 cm -1 , 0.01996μgcm -2 and 2.49 respectively. In the extraction of copper(II), several affecting factors including the solution pH, ligand concentration, equilibrium time, effect of foreign ions are optimized. The interfering effects of various cations and anions were also studied and use of masking agents enhances the selectivity of the method. The chromogenic sulphur containing reagent, 4-(4'-chlorobenzylideneimino)-3-methyl-5-mercapto-1, 2, 4-triazole has been synthesized in a single step with high purity and yield. The synthesized reagent has been successfully applied first time for determination of copper(II). The reagent forms stable chelate with copper(II) in buffer medium instantly and quantitatively extracted in chloroform within a minute. The method is successfully applied for the determination of copper(II) in various synthetic mixtures, complexes, fertilizers, environmental samples such as food samples, leafy vegetables, and water samples. The results are compared with those obtained with a reference procedure. Good agreement was attained. All the obtained results are indicative of a convenient, fast method for the extraction and quantification of micro levels of copper(II) from various environmental matrices without use of sophisticated instrumentation and procedure. The method showed a relative standard deviation of 0.42%. Copyright © 2017 Elsevier B.V. All rights reserved.

Summary of CPAS Gen II Parachute Analysis

NASA Technical Reports Server (NTRS)

Morris, Aaron L.; Bledsoe, Kristin J.; Fraire, Usbaldo, Jr.; Moore, James W.; Olson, Leah M.; Ray, Eric

2011-01-01

The Orion spacecraft is currently under development by NASA and Lockheed Martin. Like Apollo, Orion will use a series of parachutes to slow its descent and splashdown safely. The Orion parachute system, known as the CEV Parachute Assembly System (CPAS), is being designed by NASA, the Engineering and Science Contract Group (ESCG), and Airborne Systems. The first generation (Gen I) of CPAS testing consisted of thirteen tests and was executed in the 2007-2008 timeframe. The Gen I tests provided an initial understanding of the CPAS parachutes. Knowledge gained from Gen I testing was used to plan the second generation of testing (Gen II). Gen II consisted of six tests: three singleparachute tests, designated as Main Development Tests, and three Cluster Development Tests. Gen II required a more thorough investigation into parachute performance than Gen I. Higher fidelity instrumentation, enhanced analysis methods and tools, and advanced test techniques were developed. The results of the Gen II test series are being incorporated into the CPAS design. Further testing and refinement of the design and model of parachute performance will occur during the upcoming third generation of testing (Gen III). This paper will provide an overview of the developments in CPAS analysis following the end of Gen I, including descriptions of new tools and techniques as well as overviews of the Gen II tests.

Exogenous and endogenous angiotensin-II decrease renal cortical oxygen tension in conscious rats by limiting renal blood flow.

PubMed

Emans, Tonja W; Janssen, Ben J; Pinkham, Maximilian I; Ow, Connie P C; Evans, Roger G; Joles, Jaap A; Malpas, Simon C; Krediet, C T Paul; Koeners, Maarten P

2016-11-01

Our understanding of the mechanisms underlying the role of hypoxia in the initiation and progression of renal disease remains rudimentary. We have developed a method that allows wireless measurement of renal tissue oxygen tension in unrestrained rats. This method provides stable and continuous measurements of cortical tissue oxygen tension (PO2) for more than 2 weeks and can reproducibly detect acute changes in cortical oxygenation. Exogenous angiotensin-II reduced renal cortical tissue PO2 more than equi-pressor doses of phenylephrine, probably because it reduced renal oxygen delivery more than did phenylephrine. Activation of the endogenous renin-angiotensin system in transgenic Cyp1a1Ren2 rats reduced cortical tissue PO2; in this model renal hypoxia precedes the development of structural pathology and can be reversed acutely by an angiotensin-II receptor type 1 antagonist. Angiotensin-II promotes renal hypoxia, which may in turn contribute to its pathological effects during development of chronic kidney disease. We hypothesised that both exogenous and endogenous angiotensin-II (AngII) can decrease the partial pressure of oxygen (PO2) in the renal cortex of unrestrained rats, which might in turn contribute to the progression of chronic kidney disease. Rats were instrumented with telemeters equipped with a carbon paste electrode for continuous measurement of renal cortical tissue PO2. The method reproducibly detected acute changes in cortical oxygenation induced by systemic hyperoxia and hypoxia. In conscious rats, renal cortical PO2 was dose-dependently reduced by intravenous AngII. Reductions in PO2 were significantly greater than those induced by equi-pressor doses of phenylephrine. In anaesthetised rats, renal oxygen consumption was not affected, and filtration fraction was increased only in the AngII infused animals. Oxygen delivery decreased by 50% after infusion of AngII and renal blood flow (RBF) fell by 3.3 ml min -1 . Equi-pressor infusion of phenylephrine did not significantly reduce RBF or renal oxygen delivery. Activation of the endogenous renin-angiotensin system in Cyp1a1Ren2 transgenic rats reduced cortical tissue PO2. This could be reversed within minutes by pharmacological angiotensin-II receptor type 1 (AT 1 R) blockade. Thus AngII is an important modulator of renal cortical oxygenation via AT 1 receptors. AngII had a greater influence on cortical oxygenation than did phenylephrine. This phenomenon appears to be attributable to the profound impact of AngII on renal oxygen delivery. We conclude that the ability of AngII to promote renal cortical hypoxia may contribute to its influence on initiation and progression of chronic kidney disease. © 2016 The Authors. The Journal of Physiology published by John Wiley & Sons Ltd on behalf of The Physiological Society.

Solid-phase extraction of some heavy metal ions on a double-walled carbon nanotube disk and determination by flame atomic absorption spectrometry.

PubMed

Karatepe, Aslihan; Soylak, Mustafa; Elçi, Latif

2011-01-01

A new preconcentration method was developed for the determination of trace amounts of Cu(II), Fe(III), Pb(II), Ni(II), and Cd(II) on a double-walled carbon nanotube disk. 4-(2-Thiazolylazo) resorcinol was used as a complexing reagent. The effects of parameters, including pH of the solutions, amounts of complexing reagent, eluent type, sample volume, flow rates of solutions, and matrix ions were examined for quantitative recoveries of the studied analyte ions. The retained metal ions were eluted by 2 M HNO3. The LOD values for the analytes were in the range of 0.7-4.4 microg/mL. Natural water samples and standard reference materials were analyzed by the presented method.

75 FR 14170 - Medical Device Epidemiology Network: Developing Partnership Between the Center for Devices and...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-24

... methods for medical device comparative analyses, best practices and best design and analysis methods. II... the performance of medical devices (including comparative effectiveness studies). The centers...

Bacterial group II introns: not just splicing.

PubMed

Toro, Nicolás; Jiménez-Zurdo, José Ignacio; García-Rodríguez, Fernando Manuel

2007-04-01

Group II introns are both catalytic RNAs (ribozymes) and mobile retroelements that were discovered almost 14 years ago. It has been suggested that eukaryotic mRNA introns might have originated from the group II introns present in the alphaproteobacterial progenitor of the mitochondria. Bacterial group II introns are of considerable interest not only because of their evolutionary significance, but also because they could potentially be used as tools for genetic manipulation in biotechnology and for gene therapy. This review summarizes what is known about the splicing mechanisms and mobility of bacterial group II introns, and describes the recent development of group II intron-based gene-targetting methods. Bacterial group II intron diversity, evolutionary relationships, and behaviour in bacteria are also discussed.

3-D Reconstruction of Macular Type II Cell Innervation Patterns in Space-Flight and Control Rats

NASA Technical Reports Server (NTRS)

Ross, Muriel Dorothy; Montgomery, K.; Linton, S.; Cheng, R.; Tomko, David L. (Technical Monitor)

1995-01-01

A semiautomated method for reconstructing objects from serial thin sections has been developed in the Biocomputation Center. The method is being used to completely, for the first time, type II hair cells and their innervations. The purposes are to learn more about the fundamental circuitry of the macula on Earth and to determine whether changes in connectivities occur under space flight conditions. Data captured directly from a transmission electron microscope via a video camera are sent to a graphics workstation. There, the digitized micrographs are mosaicked into sections and contours are traced, registered and displayed by semiautomated methods. Current reconstructions are of type II cells from the medial part of rat maculas collected in-flight on the Space Life Sciences-2 mission, 4.5 hrs post-flight, and from a ground control. Results show that typical type II cells receive processes from tip to six nearby calyces or afferents. Nearly all processes are elongated and have bouton-like enlargements; some have numerous vesicles. Multiple (2 to 4) processes from a single calyx to a type II cell are common, and approximately 1/3 of the processes innervale 2 or 3 type II cells or a neighboring cluster. From 2% to 6% of the cells resemble type I cells morphologically but have demi-calyces. Thus far, increments in synaptic number in type II cells of flight rats are prominent along processes that supply two hair cells. It is clear that reconstruction methods provide insights into details of macular circuitry not obtainable by other techniques. The results demonstrate a morphological basis for interactions between adjacent receptive fields through feed back-feed forward connections, and for dynamic alterations in receptive field range and activity during preprocessing of linear acceleratory information by the maculas. The reconstruction method we have developed will find further applications in the study of the details of neuronal architecture of more complex systems, to seek out shared organizational properties or neuronal networks and to understand better localization of synaptic changes in altered environments.

A Reliability Simulator for Radiation-Hard Microelectronics Development

DTIC Science & Technology

1991-07-01

1 3.0 PHASE II WORK PLANS ................................................................ 2... plan . The correlation experimental details including the devices utilized, the hot-carrier stressing and the wafer-level radiation correlation procedure...channel devices, and a new lifetime extrapolation method is demonstrated for p-channel devices. 3.0 PHASE II WORK PLANS The Phase 1I program consisted of

A convenient method for determination of quizalofop-p-ethyl based on the fluorescence quenching of eosin Y in the presence of Pd(II)

NASA Astrophysics Data System (ADS)

Wu, Huan; Zhao, Yanmei; Tan, Xuanping; Zeng, Xiaoqing; Guo, Yuan; Yang, Jidong

2017-03-01

A convenient fluorescence quenching method for determination of Quizalofop-p-ethyl(Qpe) was proposed in this paper. Eosin Y(EY) is a red dye with strong green fluorescence (λex/λem = 519/540 nm). The interaction between EY, Pd(II) and Qpe was investigated by fluorescence spectroscopy, resonance Rayleigh scattering(RRS) and UV-Vis absorption. Based on changes in spectrum, Pd(II) associated with Qpe giving a positively charged chelate firstly, then reacted with EY through electrostatic and hydrophobic interaction formed ternary chelate could be demonstrated. Under optimum conditions, the fluorescence intensity of EY could be quenched by Qpe in the presence of Pd(II) and the RRS intensity had a remarkable enhancement, which was directly proportional to the Qpe concentration within a certain concentration range, respectively. Based on the fluorescence quenching of EY-Pd(II) system by Qpe, a novel, convenient and specific method for Qpe determination was developed. To our knowledge, this is the first fluorescence method for determination of Qpe was reported. The detection limit for Qpe was 20.3 ng/mL and the quantitative determination range was 0.04-1.0 μg/mL. The method was highly sensitive and had larger detection range compared to other methods. The influence of coexisting substances was investigated with good anti-interference ability. The new analytical method has been applied to determine of Qpe in real samples with satisfactory results.

A dispersive liquid--liquid microextraction methodology for copper (II) in environmental samples prior to determination using microsample injection flame atomic absorption spectrometry.

PubMed

Alothman, Zeid A; Habila, Mohamed; Yilmaz, Erkan; Soylak, Mustafa

2013-01-01

A simple, environmentally friendly, and efficient dispersive liquid-liquid microextraction method combined with microsample injection flame atomic absorption spectrometry was developed for the separation and preconcentration of Cu(II). 2-(5-Bromo-2-pyridylazo)-5-(diethylamino)phenol (5-Br-PADAP) was used to form a hydrophobic complex of Cu(II) ions in the aqueous phase before extraction. To extract the Cu(II)-5-Br-PADAP complex from the aqueous phase to the organic phase, 2.0 mL of acetone as a disperser solvent and 200 microL of chloroform as an extraction solvent were used. The influences of important analytical parameters, such as the pH, types and volumes of the extraction and disperser solvents, amount of chelating agent, sample volume, and matrix effects, on the microextraction procedure were evaluated and optimized. Using the optimal conditions, the LOD, LOQ, preconcentration factor, and RSD were determined to be 1.4 microg/L, 4.7 microg/L, 120, and 6.5%, respectively. The accuracy of the proposed method was investigated using standard addition/recovery tests. The analysis of certified reference materials produced satisfactory analytical results. The developed method was applied for the determination of Cu in real samples.

Experimental and Theoretical Study of the Temperature Performance of Type-II Quantum Well Lasers

DTIC Science & Technology

2007-05-31

performance of type-II Interband Cascade (IC) GaSb-based semiconductor lasers has been developed. The method includes comparing the temperature-concentration... dependence at the laser threshold with steady-state carrier heating characteristics. The number of cascades in prototype type-II IC lasers has been...Monroy, and R.L.Tober, "Wavelength Tuning of Interband Cascade Laser Based on the Stark Effect", in “Future Trends in Microelectronics” ed. by

On-line solid phase selective separation and preconcentration of Cd(II) by solid-phase extraction using carbon active modified with methyl thymol blue.

PubMed

Ensafi, Ali A; Ghaderi, Ali R

2007-09-05

An on-line flow system was used to develop a selective and efficient on-line sorbent extraction preconcentration system for cadmium. The method is based on adsorption of cadmium ions onto the activated carbon modified with methyl thymol blue. Then the adsorbed ions were washed using 0.5M HNO(3) and the eluent was used to determine the Cd(II) ions using flame atomic absorption spectrometry. The results obtained show that the modified activated carbon has the greatest adsorption capacity of 80 microg of Cd(II) per 1.0 g of the solid phase. The optimal pH value for the quantitative preconcentration was 9.0 and full desorption is achieved by using 0.5M HNO(3) solution. It is established that the solid phase can be used repeatedly without a considerable adsorption capacity loss. The detection limit was less than 1 ngmL(-1) Cd(II), with an enrichment factor of 1000. The calibration graph was linear in the range of 1-2000 ngmL(-1) Cd(II). The developed method has been applied to the determination of trace cadmium (II) in water samples and in the following reference materials: sewage sludge (CRM144R), and sea water (CASS.4) with satisfactory results. The accuracy was assessed through recovery experiments.

Analysis of: A Military Leadership Assessment Development Program

DTIC Science & Technology

1990-05-01

assessment pro:’gram. Reliance, however, on these to the enclusion of other research methods such as direct observation, would engender criticism. (15:238...XE A~ICOLLEGE RESEARCH REPORT AD-A241 082 I~I~lhII 111IIJ ldII~l I "~ANALYSIS OF: A MILITARY LEADERSHIP ASSESSMENT DEVELOPMENT PROGRAM COMMANDER...SUBMITTED TO THE FACULTY IN FULFILLMENT OF THE RESEARCH REQU I REMENT Research Advisor: Col. Bryan Strickland MAXWELL AIR FORCE BASE, ALABAMA MAY, 1990

Double-blind placebo-controlled challenges for peanut allergy the efficiency of blinding procedures and the allergenic activity of peanut availability in the recipes.

PubMed

van Odijk, J; Ahlstedt, S; Bengtsson, U; Borres, M P; Hulthén, L

2005-05-01

A firm diagnosis of double-blind placebo-controlled food challenge (DBPCFC) would facilitate the diagnosis in patients with uncertain history of reaction. Guidelines are lacking for an upper provoking dose and how to hide high concentrations of peanuts. To develop and evaluate a double-blind recipe with minimum 10% of peanut. To compare the recipe with published recipes regarding blindness, taste, texture and immunoglobulin (Ig)E antibody binding to peanut. A recipe (I) with 10% of peanut was developed evaluated and used in DBPCFC. The challenges were followed by development of a concentrated recipe (II) (15% peanut, 25% fat). Recipe II was compared with the only published recipe (III) (11% peanut, 7% fat) regarding taste, texture and availability of peanut. Recipe IV (12% peanut, 10% fat) was developed using the same methods. The binding of IgE in the recipes was measured using an inhibition method. During challenges, one patient reacted after 4 g, emphasizing the need for blinding recipes containing high doses of peanut. Evaluation between recipes II and III, only recipe II was regarded as blind by the taste panels. A tenfold lower availability of peanut protein in the recipe II was found at 50% of inhibition. Recipe IV had a better IgE binding that did not differ from the original peanut extract. The peanut taste and texture can be hidden in a challenge medium. The fat content was important for the availability of the allergenic protein in challenges. The availability of allergens must be taken into consideration when used for DBPCFC.

Polymeric mercaptosilane-modified platinum electrodes for elimination of interferants in glucose biosensors.

PubMed

Jung, S K; Wilson, G S

1996-02-15

An oxidase-based glucose sensor has been developed that uses a mercaptosilane-modified platinum electrode to achieve selectivity of electrochemical interferants. A platinum-iridium (9:1) wire (0.178 mm o.d., sensing area of 1.12 mm2) is modified with (3-mercaptopropyl)trimethoxysilane. The modified sensors show excellent operational stability for more than 5 days. Glucose oxidase is immobilized on the modified surface (i) by using 3-maleimidopropionic acid as a linker or (ii) by cross-liking with bovine serum albumin using glutaraldehyde. Sensitivities in the range of 9.97 nA/mM glucose are observed when the enzyme is immobilized by method ii. Lower sensitivities (1.13 x 10(-1) nA/mM glucose) are observed when immobilization method i is employed. In terms of linear response range, the sensor enzyme-immobilized by method i is superior to that immobilized by method ii. The linearity is improved upon coating the enzyme layer with polyurethane. The sensor immobilized by method ii and coated with polyurethane exhibits a linear range to 15 mM glucose and excellent selectivity to glucose (0.47 nA/mM) against interferants such as ascorbic acid, uric acid, and acetaminophen.

Autogenous accelerated curing of concrete cylinders. Part II, Development of a moisture measuring method.

DOT National Transportation Integrated Search

1970-01-01

Through a literature study, approximately fifty methods of measuring moisture were investigated to ascertain a suitable method for use in measuring moisture changes in 6 inch by 12 inch concrete cylinders cured by the autogenous accelerated curing me...

A rapid method for soil cement design : Louisiana slope value method : part II : evaluation.

DOT National Transportation Integrated Search

1966-05-01

This report is an evaluation of the recently developed "Louisiana Slope Value Method". : The conclusion drawn are based on data from 637 separate samples representing nearly all major soil groups in Louisiana that are suitable for cement stabilizatio...

Current antiviral drugs and their analysis in biological materials - Part II: Antivirals against hepatitis and HIV viruses.

PubMed

Nováková, Lucie; Pavlík, Jakub; Chrenková, Lucia; Martinec, Ondřej; Červený, Lukáš

2018-01-05

This review is a Part II of the series aiming to provide comprehensive overview of currently used antiviral drugs and to show modern approaches to their analysis. While in the Part I antivirals against herpes viruses and antivirals against respiratory viruses were addressed, this part concerns antivirals against hepatitis viruses (B and C) and human immunodeficiency virus (HIV). Many novel antivirals against hepatitis C virus (HCV) and HIV have been introduced into the clinical practice over the last decade. The recent broadening portfolio of these groups of antivirals is reflected in increasing number of developed analytical methods required to meet the needs of clinical terrain. Part II summarizes the mechanisms of action of antivirals against hepatitis B virus (HBV), HCV, and HIV, their use in clinical practice, and analytical methods for individual classes. It also provides expert opinion on state of art in the field of bioanalysis of these drugs. Analytical methods reflect novelty of these chemical structures and use by far the most current approaches, such as simple and high-throughput sample preparation and fast separation, often by means of UHPLC-MS/MS. Proper method validation based on requirements of bioanalytical guidelines is an inherent part of the developed methods. Copyright © 2017 Elsevier B.V. All rights reserved.

Development of two highly sensitive immunoassays for detection of copper ions and a suite of relevant immunochemicals.

PubMed

Zhao, Hongwei; Nan, Tiegui; Tan, Guiyu; Gao, Wei; Cao, Zhen; Sun, Shuo; Li, Zhaohu; Li, Qing X; Wang, Baomin

2011-09-19

Availability of highly sensitive assays for metal ions can help monitor and manage the environmental and food contamination. In the present study, a monoclonal antibody against Copper(II)-ethylenediaminetetraacetic acid was used to develop two sensitive ELISAs for Cu(II) analysis. Cobalt(II)-EDTA-BSA was the coating antigen in a heterologous indirect competitive ELISA (hicELISA), whereas Co(II)-EDTA-BSA-horseradish peroxidase (HRP) was the enzyme tracer in a heterologous direct competitive ELISA (hdcELISA). Both ELISAs were validated for detecting the content of Cu(II) in environmental waters. The ELISA data agreed well with those from graphite furnace atomic absorption spectroscopy. The methods of developing the Cu(II) hicELISA and hdcELISA are potentially applicable for developing ELISAs for other metals. The chelator-protein complexes such as EDTA-BSA and EDTA-BSA-HRP can form a suite of metal complexes having the consistent hapten density, location and orientation on the conjugates except the difference of the metal core, which can be used as ideal reagents to investigate the relationship between assay sensitivity and antibody affinities for the haptens and the analytes. The strategy of conjugating a haptenated protein directly with HRP can reduce the loss of HRP activity during the conjugation reaction and thus can be applicable for the development of ELISAs for small molecules. Copyright © 2011. Published by Elsevier B.V.

Prediction of MHC class II binding affinity using SMM-align, a novel stabilization matrix alignment method

PubMed Central

Nielsen, Morten; Lundegaard, Claus; Lund, Ole

2007-01-01

Background Antigen presenting cells (APCs) sample the extra cellular space and present peptides from here to T helper cells, which can be activated if the peptides are of foreign origin. The peptides are presented on the surface of the cells in complex with major histocompatibility class II (MHC II) molecules. Identification of peptides that bind MHC II molecules is thus a key step in rational vaccine design and developing methods for accurate prediction of the peptide:MHC interactions play a central role in epitope discovery. The MHC class II binding groove is open at both ends making the correct alignment of a peptide in the binding groove a crucial part of identifying the core of an MHC class II binding motif. Here, we present a novel stabilization matrix alignment method, SMM-align, that allows for direct prediction of peptide:MHC binding affinities. The predictive performance of the method is validated on a large MHC class II benchmark data set covering 14 HLA-DR (human MHC) and three mouse H2-IA alleles. Results The predictive performance of the SMM-align method was demonstrated to be superior to that of the Gibbs sampler, TEPITOPE, SVRMHC, and MHCpred methods. Cross validation between peptide data set obtained from different sources demonstrated that direct incorporation of peptide length potentially results in over-fitting of the binding prediction method. Focusing on amino terminal peptide flanking residues (PFR), we demonstrate a consistent gain in predictive performance by favoring binding registers with a minimum PFR length of two amino acids. Visualizing the binding motif as obtained by the SMM-align and TEPITOPE methods highlights a series of fundamental discrepancies between the two predicted motifs. For the DRB1*1302 allele for instance, the TEPITOPE method favors basic amino acids at most anchor positions, whereas the SMM-align method identifies a preference for hydrophobic or neutral amino acids at the anchors. Conclusion The SMM-align method was shown to outperform other state of the art MHC class II prediction methods. The method predicts quantitative peptide:MHC binding affinity values, making it ideally suited for rational epitope discovery. The method has been trained and evaluated on the, to our knowledge, largest benchmark data set publicly available and covers the nine HLA-DR supertypes suggested as well as three mouse H2-IA allele. Both the peptide benchmark data set, and SMM-align prediction method (NetMHCII) are made publicly available. PMID:17608956

Prediction of MHC class II binding affinity using SMM-align, a novel stabilization matrix alignment method.

PubMed

Nielsen, Morten; Lundegaard, Claus; Lund, Ole

2007-07-04

Antigen presenting cells (APCs) sample the extra cellular space and present peptides from here to T helper cells, which can be activated if the peptides are of foreign origin. The peptides are presented on the surface of the cells in complex with major histocompatibility class II (MHC II) molecules. Identification of peptides that bind MHC II molecules is thus a key step in rational vaccine design and developing methods for accurate prediction of the peptide:MHC interactions play a central role in epitope discovery. The MHC class II binding groove is open at both ends making the correct alignment of a peptide in the binding groove a crucial part of identifying the core of an MHC class II binding motif. Here, we present a novel stabilization matrix alignment method, SMM-align, that allows for direct prediction of peptide:MHC binding affinities. The predictive performance of the method is validated on a large MHC class II benchmark data set covering 14 HLA-DR (human MHC) and three mouse H2-IA alleles. The predictive performance of the SMM-align method was demonstrated to be superior to that of the Gibbs sampler, TEPITOPE, SVRMHC, and MHCpred methods. Cross validation between peptide data set obtained from different sources demonstrated that direct incorporation of peptide length potentially results in over-fitting of the binding prediction method. Focusing on amino terminal peptide flanking residues (PFR), we demonstrate a consistent gain in predictive performance by favoring binding registers with a minimum PFR length of two amino acids. Visualizing the binding motif as obtained by the SMM-align and TEPITOPE methods highlights a series of fundamental discrepancies between the two predicted motifs. For the DRB1*1302 allele for instance, the TEPITOPE method favors basic amino acids at most anchor positions, whereas the SMM-align method identifies a preference for hydrophobic or neutral amino acids at the anchors. The SMM-align method was shown to outperform other state of the art MHC class II prediction methods. The method predicts quantitative peptide:MHC binding affinity values, making it ideally suited for rational epitope discovery. The method has been trained and evaluated on the, to our knowledge, largest benchmark data set publicly available and covers the nine HLA-DR supertypes suggested as well as three mouse H2-IA allele. Both the peptide benchmark data set, and SMM-align prediction method (NetMHCII) are made publicly available.

Near-Infrared II Fluorescence for Imaging Hindlimb Vessel Regeneration with Dynamic Tissue Perfusion Measurement

PubMed Central

Hong, Guosong; Lee, Jerry C.; Jha, Arshi; Diao, Shuo; Nakayama, Karina H.; Hou, Luqia; Doyle, Timothy C.; Robinson, Joshua T.; Antaris, Alexander L.; Dai, Hongjie; Cooke, John P.; Huang, Ngan F.

2014-01-01

Background Real-time vascular imaging that provides both anatomic and hemodynamic information could greatly facilitate the diagnosis of vascular diseases and provide accurate assessment of therapeutic effects. Here we have developed a novel fluorescence-based all-optical method, named near-infrared II (NIR-II) fluorescence imaging, to image murine hindlimb vasculature and blood flow in an experimental model of peripheral arterial disease, by exploiting fluorescence in the NIR-II region (1000–1400 nm) of photon wavelengths. Methods and Results Owing to the reduced photon scattering of NIR-II fluorescence compared to traditional NIR fluorescence imaging and thus much deeper penetration depth into the body, we demonstrated that the mouse hindlimb vasculature could be imaged with higher spatial resolution than in vivo microCT. Furthermore, imaging over 26 days revealed a significant increase in hindlimb microvascular density in response to experimentally induced ischemia within the first 8 days of the surgery (P < 0.005), which was confirmed by histological analysis of microvascular density. Moreover, the tissue perfusion in the ischemic hindlimb could be quantitatively measured by the dynamic NIR-II method, revealing the temporal kinetics of blood flow recovery that resembled microbead-based blood flowmetry and laser Doppler blood spectroscopy. Conclusions The penetration depth of millimeters, high spatial resolution and fast acquisition rate of NIR-II imaging makes it a useful imaging tool for murine models of vascular disease. PMID:24657826

Synthesis of N₄ donor macrocyclic Schiff base ligands and their Ru (II), Pd (II), Pt (II) metal complexes for biological studies and catalytic oxidation of didanosine in pharmaceuticals.

PubMed

Ravi Krishna, E; Muralidhar Reddy, P; Sarangapani, M; Hanmanthu, G; Geeta, B; Shoba Rani, K; Ravinder, V

2012-11-01

A series of tetraaza (N(4) donor) macrocyclic ligands (L(1)-L(4)) were derived from the condensation of o-phthalaldehyde (OPA) with some substituted aromatic amines/azide, and subsequently used to synthesize the metal complexes of Ru(II), Pd(II) and Pt(II). The structures of macrocyclic ligands and their metal complexes were characterized by elemental analyses, IR, (1)H &(13)C NMR, mass and electronic spectroscopy, thermal, magnetic and conductance measurements. Both the ligands and their complexes were screened for their antibacterial activities against Gram positive and Gram negative bacteria by MIC method. Besides, these macrocyclic complexes were investigated as catalysts in the oxidation of pharmaceutical drug didanosine. The oxidized products were further treated with sulphanilic acid to develop the colored products to determine by spectrophotometrically. The current oxidation method is an environmentally friendly, simple to set-up, requires short reaction time, produces high yields and does not require co-oxidant. Copyright © 2012 Elsevier B.V. All rights reserved.

Amperometric biosensors for the determination of heavy metals

NASA Astrophysics Data System (ADS)

Compagnone, Dario; Palleschi, Giuseppe; Varallo, Giuseppe; Imperiali, PierLuigi

1995-10-01

A bioelectrochemical method for the determination of heavy metal ions has been developed. This method is based on the inhibition effect of metal ions on the enzymatic activity of oxidase enzymes. The enzymatic activity was determined with an amperometric hydrogen peroxide probe. The inhibition effect on enzymes in solution and covalently immobilized on polymeric supports has been evaluated. Hg(II) was the metal ion that inhibited almost all the enzymes, particularly glycerol-3-P oxidase. Hg(II) was detected in the 0.05/0.5 ppm range with the enzyme in solution. Calibration curves for Hg(II) were also obtained with the other oxidase enzymes in the 0.5/10 ppm range. The other metal ions tested inhibited the enzymes more specifically. The metal ion/enzyme systems which gave the best inhibition were Se(IV)/glutathione oxidase, Ni(II)/sarcosine oxidase, V(V)/glutathione oxidase, Cu(II)/alcohol oxidase from Pichia Pastoris and Cd(II)/D-aminoacid oxidase. All these metal ions were detected in the 0.1/10 ppm range using the enzymes in solution or covalently immobilized.

Oxidative demetalation of cyclohexadienyl ruthenium(II) complexes: a net Ru-mediated dearomatization.

PubMed

Pigge, F Christopher; Coniglio, John J; Rath, Nigam P

2003-05-29

[reaction: see text] An experimentally simple method for the demetalation of spirocyclic cyclohexadienylruthenium(II) complexes has been developed. Treatment of an alkoxy-substituted cyclohexadienyl complex with CuCl(2) affords either azaspiro[4.5]decane derivatives or heavily functionalized tetrahydroisoquinolines. The former reaction manifold completes a net Ru-mediated dearomatization as the organometallic starting materials are prepared from (eta(6)-arene)Ru(II) precursors. Both of these heterocyclic products are well suited for further synthetic elaboration.

Determination of GTA Welding Efficiencies

DTIC Science & Technology

1993-03-01

continue on reverse if ncessary andidentify by block number) A method is developed for estimating welding efficiencies for moving arc GTAW processes...Dutta, Co-Advi r Department of Mechanical Engineering ii ABSTRACT A method is developed for estimating welding efficiencies for moving arc GTAW ...17 Figure 10. Miller Welding Equipment ............. ... 18 Figure 11. GTAW Torch Setup for Automatic Welding. . 19 Figure 12

The Birth and Death of the Audio-Lingual Method.

ERIC Educational Resources Information Center

Zillo, Frank

This general review of the development and demise in popularity of the "audiolingual" method of teaching second languages in America underscores the impact of World War II on the changing needs of the country's manpower resources in the field of international relations. The author develops the thesis that the urgent need for speakers of second…

Applications of organo-silica nanocomposites for SPNE of Hg(II)

NASA Astrophysics Data System (ADS)

Kaur, Anupreet

2016-02-01

An analytical method using modified SiO2 nanoparticles as solid-phase extractant has been developed for the preconcentration of trace amounts of Hg(II) in different water samples. Conditions of the analysis such as preconcentration factor, effect of pH, sample volume, shaking time, elution conditions and effects of interfering ions for the recovery of analyte were investigated. The adsorption capacity of nanometer SiO2-APTMS was found to be 181.42 µmol g-1 at optimum pH and the detection limit (3σ) was 0.45 µg L-1. The extractant showed rapid kinetic sorption. The adsorption equilibrium of Hg(II) on nanometer SiO2-APTMS was achieved just in 15 min. Adsorbed Hg(II) was easily eluted with 4 mL of 2.0 M hydrochloric acid. The maximum preconcentration factor was 75. The method was applied for the determination of trace amounts of Hg(II) in various synthetic samples and water samples.

Phosphate effects on copper(II) and lead(II) sorption to ferrihydrite

NASA Astrophysics Data System (ADS)

Tiberg, Charlotta; Sjöstedt, Carin; Persson, Ingmar; Gustafsson, Jon Petter

2013-11-01

Transport of lead(II) and copper(II) ions in soil is affected by the soil phosphorus status. Part of the explanation may be that phosphate increases the adsorption of copper(II) and lead(II) to iron (hydr)oxides in soil, but the details of these interactions are poorly known. Knowledge about such mechanisms is important, for example, in risk assessments of contaminated sites and development of remediation methods. We used a combination of batch experiments, extended X-ray absorption fine structure (EXAFS) spectroscopy and surface complexation modeling with the three-plane CD-MUSIC model to study the effect of phosphate on sorption of copper(II) and lead(II) to ferrihydrite. The aim was to identify the surface complexes formed and to derive constants for the surface complexation reactions. In the batch experiments phosphate greatly enhanced the adsorption of copper(II) and lead(II) to ferrihydrite at pH < 6. The largest effects were seen for lead(II).

Determination of some metal ions in various meat and baby food samples by atomic spectrometry.

PubMed

Daşbaşı, Teslima; Saçmacı, Şerife; Ülgen, Ahmet; Kartal, Şenol

2016-04-15

In this paper, we report a simple and rapid solid phase extraction system for the separation/preconcentration and determination of Cd(II), Co(II), Cu(II), Fe(III), Cr(III), Pb(II), and Zn(II) ions by flame atomic absorption spectrometry (FAAS). This method is based upon the retention of metal ions on a column packed with poly[N-(3-methyl-1H-indole-1-yl)]-2-methacrylamide-co-2-acrylamido-2-methyl-1-propane sulphonic acid-co divinylbenzene] (MMAD) resin as a solid-phase extraction (SPE) sorbent at pH 8. At the optimized conditions, the limits of detection (3 s/b) between 0.12 and 1.6 μg L(-1), preconcentration factor of 100, and the relative standard deviation of ⩽1.8% were achieved (n=10). The accuracy of the method was verified by analyzing certified reference materials (CRMs) and performing recovery experiments. The developed method was successfully applied to the various natural water, meat products and baby food samples. The recoveries of analyte ions were found in added real samples and CRMs from 95% to 102%. Copyright © 2015 Elsevier Ltd. All rights reserved.

Chemically-modified activated carbon with ethylenediamine for selective solid-phase extraction and preconcentration of metal ions.

PubMed

Li, Zhenhua; Chang, Xijun; Zou, Xiaojun; Zhu, Xiangbing; Nie, Rong; Hu, Zheng; Li, Ruijun

2009-01-26

A new method that utilizes ethylenediamine-modified activated carbon (AC-EDA) as a solid-phase extractant has been developed for simultaneous preconcentration of trace Cr(III), Fe(III), Hg(II) and Pb(II) prior to the measurement by inductively coupled plasma optical emission spectrometry (ICP-OES). The new sorbent was prepared by oxidative surface modification. Experimental conditions for effective adsorption of trace levels of Cr(III), Fe(III), Hg(II) and Pb(II) were optimized with respect to different experimental parameters using batch and column procedures in detail. The optimum pH value for the separation of metal ions simultaneously on the new sorbent was 4.0. Complete elution of absorbed metal ions from the sorbent surface was carried out using 3.0 mL of 2% (%w/w) thiourea and 0.5 mol L(-1) HCl solution. Common coexisting ions did not interfere with the separation and determination of target metal ions. The maximum static adsorption capacity of the sorbent at optimum conditions was found to be 39.4, 28.9, 60.5 and 49.9 mg g(-1) for Cr(III), Fe(III), Hg(II) and Pb(II), respectively. The time for 94% adsorption of target metal ions was less than 2 min. The detection limits of the method was found to be 0.28, 0.22, 0.09 and 0.17 ng mL(-1) for Cr(III), Fe(III), Hg(II) and Pb(II), respectively. The precision (R.S.D.) of the method was lower 4.0% (n=8). The prepared sorbent as solid-phase extractant was successfully applied for the preconcentration of trace Cr(III), Fe(III), Hg(II) and Pb(II) in natural and certified samples with satisfactory results.

A Method to Develop Neck Injury Criteria to Aid Design and Test of Escape Systems Incorporating Helmet Mounted Displays

DTIC Science & Technology

2014-09-01

The military aviation community began designing and building ejection seats for high speed aircraft after World War II. As pilot safety became...AFIT-ENV-DS-14-S-22 A METHOD TO DEVELOP NECK INJURY CRITERIA TO AID DESIGN AND TEST OF ESCAPE SYSTEMS...protection in the United States. AFIT-ENV-DS-14-S-22 A METHOD TO DEVELOP NECK INJURY CRITERIA TO AID DESIGN AND TEST OF ESCAPE SYSTEMS

SER-LARS, Volume 11. Instructional Methods II. 1975-76 Edition.

ERIC Educational Resources Information Center

Montgomery County Intermediate Unit 23, Blue Bell, PA.

The book briefly describes several hundred instructional methods from the Special Education Resources Location Analysis and Retrieval System (SER LARS), which are intended for use in developing and carrying out individualized programs for handicapped children. Each teaching method includes an accession number; title; author; source; teacher tasks;…

Extraction and separation of Co(II) and Ni(II) from acidic sulfate solutions using Aliquat 336.

PubMed

Nayl, A A

2010-01-15

Extraction and separation of Co(II) and Ni(II) from acidic sulfate solutions by solvent extraction technique were studied using different forms of Aliquat 336 diluted with kerosene. The extraction percent of each metal ion was found to increase with increasing pH and extractant concentration. Co(II) was preferentially extracted by different forms of Aliquat 336 over Ni(II) under the same extraction conditions. From analysis of the experimental results, the extraction mechanism of R(4)N-forms was proposed with Co(II). It was found that the highest separation factor (S(Co/Ni)) value of 606.7 was obtained with 0.36 M R(4)N-SCN in kerosene from 2.0M H(2)SO(4) solution at pH 4.8 and shaking time of 20 min. Stripping of the two metal ions from the organic phase was also investigated. Based on the experimental results, a separation method was developed and tested to separate high purity Co(II), Ni(II) and Ln(III) from Ni-MH batteries leached by 2.0M H(2)SO(4). Based on the experimental results, a flow sheet was developed and tested and 0.34 g Co, 1.39 g Ln and 5.2g Ni were obtained from the leaching process.

An integrated bioanalytical method development and validation approach: case studies.

PubMed

Xue, Y-J; Melo, Brian; Vallejo, Martha; Zhao, Yuwen; Tang, Lina; Chen, Yuan-Shek; Keller, Karin M

2012-10-01

We proposed an integrated bioanalytical method development and validation approach: (1) method screening based on analyte's physicochemical properties and metabolism information to determine the most appropriate extraction/analysis conditions; (2) preliminary stability evaluation using both quality control and incurred samples to establish sample collection, storage and processing conditions; (3) mock validation to examine method accuracy and precision and incurred sample reproducibility; and (4) method validation to confirm the results obtained during method development. This integrated approach was applied to the determination of compound I in rat plasma and compound II in rat and dog plasma. The effectiveness of the approach was demonstrated by the superior quality of three method validations: (1) a zero run failure rate; (2) >93% of quality control results within 10% of nominal values; and (3) 99% incurred sample within 9.2% of the original values. In addition, rat and dog plasma methods for compound II were successfully applied to analyze more than 900 plasma samples obtained from Investigational New Drug (IND) toxicology studies in rats and dogs with near perfect results: (1) a zero run failure rate; (2) excellent accuracy and precision for standards and quality controls; and (3) 98% incurred samples within 15% of the original values. Copyright © 2011 John Wiley & Sons, Ltd.

Development of a Rotor-Body Coupled Analysis for an Active Mount Aeroelastic Rotor Testbed. Degree awarded by George Washington Univ., May 1996

NASA Technical Reports Server (NTRS)

Wilbur, Matthew L.

1998-01-01

At the Langley Research Center an active mount rotorcraft testbed is being developed for use in the Langley Transonic Dynamics Tunnel. This testbed, the second generation version of the Aeroelastic Rotor Experimental System (ARES-II), can impose rotor hub motions and measure the response so that rotor-body coupling phenomena may be investigated. An analytical method for coupling an aeroelastically scaled model rotor system to the ARES-II is developed in the current study. Models of the testbed and the rotor system are developed in independent analyses, and an impedance-matching approach is used to couple the rotor system to the testbed. The development of the analytical models and the coupling method is examined, and individual and coupled results are presented for the testbed and rotor system. Coupled results are presented with and without applied hub motion, and system loads and displacements are examined. The results show that a closed-loop control system is necessary to achieve desired hub motions, that proper modeling requires including the loads at the rotor hub and rotor control system, and that the strain-gauge balance placed in the rotating system of the ARES-II provided the best loads results.

In-Vehicle Safety Advisory And Warning System (Ivsaws), Volume II: Final Report

DOT National Transportation Integrated Search

2001-04-01

Methods for determining the workability of freshly mixed portland-cement concrete with slumps less than 51 mm (2 in) were investigated. Four potential methods to determine the workability of concrete were proposed for evaluation and development. The ...

Copper(II)-rubeanic acid coprecipitation system for separation-preconcentration of trace metal ions in environmental samples for their flame atomic absorption spectrometric determinations.

PubMed

Soylak, Mustafa; Erdogan, Nilgun D

2006-09-21

A simple and facile preconcentration procedure based on the coprecipitation of trace heavy metal ions with copper(II)-rubeanic acid complex has been developed. The analytical parameters including pH, amounts of rubeanic acid, sample volume, etc. was investigated for the quantitative recoveries of Pb(II), Fe(III), Cd(II), Au(III), Pd(II) and Ni(II). No interferic effects were observed from the concomitant ions. The detection limits for analyte ions by 3 sigma were in the range of 0.14 microg/l for iron-3.4 microg/l for lead. The proposed coprecipitation method was successfully applied to water samples from Palas Lake-Kayseri, soil and sediment samples from Kayseri and Yozgat-Turkey.

A Disposable Microfluidic Device with a Screen Printed Electrode for Mimicking Phase II Metabolism

PubMed Central

Vasiliadou, Rafaela; Nasr Esfahani, Mohammad Mehdi; Brown, Nathan J.; Welham, Kevin J.

2016-01-01

Human metabolism is investigated using several in vitro methods. However, the current methodologies are often expensive, tedious and complicated. Over the last decade, the combination of electrochemistry (EC) with mass spectrometry (MS) has a simpler and a cheaper alternative to mimic the human metabolism. This paper describes the development of a disposable microfluidic device with a screen-printed electrode (SPE) for monitoring phase II GSH reactions. The proposed chip has the potential to be used as a primary screening tool, thus complementing the current in vitro methods. PMID:27598162

Prediction of the binding affinities of peptides to class II MHC using a regularized thermodynamic model

PubMed Central

2010-01-01

Background The binding of peptide fragments of extracellular peptides to class II MHC is a crucial event in the adaptive immune response. Each MHC allotype generally binds a distinct subset of peptides and the enormous number of possible peptide epitopes prevents their complete experimental characterization. Computational methods can utilize the limited experimental data to predict the binding affinities of peptides to class II MHC. Results We have developed the Regularized Thermodynamic Average, or RTA, method for predicting the affinities of peptides binding to class II MHC. RTA accounts for all possible peptide binding conformations using a thermodynamic average and includes a parameter constraint for regularization to improve accuracy on novel data. RTA was shown to achieve higher accuracy, as measured by AUC, than SMM-align on the same data for all 17 MHC allotypes examined. RTA also gave the highest accuracy on all but three allotypes when compared with results from 9 different prediction methods applied to the same data. In addition, the method correctly predicted the peptide binding register of 17 out of 18 peptide-MHC complexes. Finally, we found that suboptimal peptide binding registers, which are often ignored in other prediction methods, made significant contributions of at least 50% of the total binding energy for approximately 20% of the peptides. Conclusions The RTA method accurately predicts peptide binding affinities to class II MHC and accounts for multiple peptide binding registers while reducing overfitting through regularization. The method has potential applications in vaccine design and in understanding autoimmune disorders. A web server implementing the RTA prediction method is available at http://bordnerlab.org/RTA/. PMID:20089173

BetaTPred: prediction of beta-TURNS in a protein using statistical algorithms.

PubMed

Kaur, Harpreet; Raghava, G P S

2002-03-01

beta-turns play an important role from a structural and functional point of view. beta-turns are the most common type of non-repetitive structures in proteins and comprise on average, 25% of the residues. In the past numerous methods have been developed to predict beta-turns in a protein. Most of these prediction methods are based on statistical approaches. In order to utilize the full potential of these methods, there is a need to develop a web server. This paper describes a web server called BetaTPred, developed for predicting beta-TURNS in a protein from its amino acid sequence. BetaTPred allows the user to predict turns in a protein using existing statistical algorithms. It also allows to predict different types of beta-TURNS e.g. type I, I', II, II', VI, VIII and non-specific. This server assists the users in predicting the consensus beta-TURNS in a protein. The server is accessible from http://imtech.res.in/raghava/betatpred/

Evaluating Phase II of a New York City-Wide STEM Initiative Using Propensity Score Methods: A Replication Study

ERIC Educational Resources Information Center

Thomas, Ally S.; Bonner, Sarah M.; Everson, Howard T.

2014-01-01

Recently, the authors have been exploring the use of propensity score methods for developing evidence of program impact. Specifically, they have been developing evidence (after one year of implementation) of the effects of the Math Science Partnership in New York City ("MSPinNYC2") on high school students' achievement--both in terms of…

Analysis of health trait data from on-farm computer systems in the U.S. II: Comparison of genomic analyses including two-stage and single-step methods

USDA-ARS?s Scientific Manuscript database

The development of genomic selection methodology, with accompanying substantial gains in reliability for low-heritability traits, may dramatically improve the feasibility of genetic improvement of dairy cow health. Many methods for genomic analysis have now been developed, including the “Bayesian Al...

I. Developing Methods for the Analysis of Chemistry Students' Inscriptions, II. Exploring the Regioselectivity of 1,3-Dipolar Cycloadditions of Munchnones, III. Stereochemical Investigations of C-H Activation Reactions Involving Germylene and Stannylene/Aryl Iodide Reagents

ERIC Educational Resources Information Center

Kiste, Alan L.

2009-01-01

I. Analyzing and comparing student-generated inscriptions in chemistry is crucial to gaining insight into students' understanding about chemistry concepts. Thus, we developed two methods of analyzing student-generated inscriptions: features analysis and thematic analysis. We have also demonstrated how these methods are able to discern differences…

Portable Multispectral Colorimeter for Metallic Ion Detection and Classification

PubMed Central

Jaimes, Ruth F. V. V.; Borysow, Walter; Gomes, Osmar F.; Salcedo, Walter J.

2017-01-01

This work deals with a portable device system applied to detect and classify different metallic ions as proposed and developed, aiming its application for hydrological monitoring systems such as rivers, lakes and groundwater. Considering the system features, a portable colorimetric system was developed by using a multispectral optoelectronic sensor. All the technology of quantification and classification of metallic ions using optoelectronic multispectral sensors was fully integrated in the embedded hardware FPGA ( Field Programmable Gate Array) technology and software based on virtual instrumentation (NI LabView®). The system draws on an indicative colorimeter by using the chromogen reagent of 1-(2-pyridylazo)-2-naphthol (PAN). The results obtained with the signal processing and pattern analysis using the method of the linear discriminant analysis, allows excellent results during detection and classification of Pb(II), Cd(II), Zn(II), Cu(II), Fe(III) and Ni(II) ions, with almost the same level of performance as for those obtained from the Ultravioled and visible (UV-VIS) spectrophotometers of high spectral resolution. PMID:28788082

Portable Multispectral Colorimeter for Metallic Ion Detection and Classification.

PubMed

Braga, Mauro S; Jaimes, Ruth F V V; Borysow, Walter; Gomes, Osmar F; Salcedo, Walter J

2017-07-28

This work deals with a portable device system applied to detect and classify different metallic ions as proposed and developed, aiming its application for hydrological monitoring systems such as rivers, lakes and groundwater. Considering the system features, a portable colorimetric system was developed by using a multispectral optoelectronic sensor. All the technology of quantification and classification of metallic ions using optoelectronic multispectral sensors was fully integrated in the embedded hardware FPGA ( Field Programmable Gate Array) technology and software based on virtual instrumentation (NI LabView ® ). The system draws on an indicative colorimeter by using the chromogen reagent of 1-(2-pyridylazo)-2-naphthol (PAN). The results obtained with the signal processing and pattern analysis using the method of the linear discriminant analysis, allows excellent results during detection and classification of Pb(II), Cd(II), Zn(II), Cu(II), Fe(III) and Ni(II) ions, with almost the same level of performance as for those obtained from the Ultravioled and visible (UV-VIS) spectrophotometers of high spectral resolution.

36 CFR 4.30 - Bicycles.

Code of Federal Regulations, 2013 CFR

2013-07-01

... shall be developed and constructed in accordance with appropriate NPS sustainable trail design... trail to sustainable condition; and (ii) Life cycle maintenance costs, safety considerations, methods to...

36 CFR 4.30 - Bicycles.

Code of Federal Regulations, 2014 CFR

2014-07-01

... shall be developed and constructed in accordance with appropriate NPS sustainable trail design... trail to sustainable condition; and (ii) Life cycle maintenance costs, safety considerations, methods to...

Elemental analysis of glass by laser ablation inductively coupled plasma optical emission spectrometry (LA-ICP-OES).

PubMed

Schenk, Emily R; Almirall, José R

2012-04-10

The elemental analysis of glass evidence has been established as a powerful discrimination tool for forensic analysts. Laser ablation inductively coupled plasma optical emission spectrometry (LA-ICP-OES) has been compared to laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) and energy dispersive micro X-ray fluorescence spectroscopy (μXRF/EDS) as competing instrumentation for the elemental analysis of glass. The development of a method for the forensic analysis of glass coupling laser ablation to ICP-OES is presented for the first time. LA-ICP-OES has demonstrated comparable analytical performance to LA-ICP-MS based on the use of the element menu, Al (Al I 396.15 nm), Ba (Ba II 455.40 nm), Ca (Ca II 315.88 nm), Fe (Fe II 238.20 nm), Li (Li I 670.78 nm), Mg (Mg I 285.21 nm), Sr (Sr II 407.77 nm), Ti (Ti II 368.51 nm), and Zr (Zr II 343.82 nm). The relevant figures of merit, such as precision, accuracy and sensitivity, are presented and compared to LA-ICP-MS. A set of 41 glass samples was used to assess the discrimination power of the LA-ICP-OES method in comparison to other elemental analysis techniques. This sample set consisted of several vehicle glass samples that originated from the same source (inside and outside windshield panes) and several glass samples that originated from different vehicles. Different match criteria were used and compared to determine the potential for Type I and Type II errors. It was determined that broader match criteria is more applicable to the forensic comparison of glass analysis because it can reduce the affect that micro-heterogeneity inherent in the glass fragments and a less than ideal sampling strategy can have on the interpretation of the results. Based on the test set reported here, a plus or minus four standard deviation (± 4s) match criterion yielded the lowest possibility of Type I and Type II errors. The developed LA-ICP-OES method has been shown to perform similarly to LA-ICP-MS in the discrimination among different sources of glass while offering the advantages of a lower cost of acquisition and operation of analytical instrumentation making ICP-OES a possible alternative elemental analysis method for the forensic laboratory. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

RCP: a novel probe design bias correction method for Illumina Methylation BeadChip.

PubMed

Niu, Liang; Xu, Zongli; Taylor, Jack A

2016-09-01

The Illumina HumanMethylation450 BeadChip has been extensively utilized in epigenome-wide association studies. This array and its successor, the MethylationEPIC array, use two types of probes-Infinium I (type I) and Infinium II (type II)-in order to increase genome coverage but differences in probe chemistries result in different type I and II distributions of methylation values. Ignoring the difference in distributions between the two probe types may bias downstream analysis. Here, we developed a novel method, called Regression on Correlated Probes (RCP), which uses the existing correlation between pairs of nearby type I and II probes to adjust the beta values of all type II probes. We evaluate the effect of this adjustment on reducing probe design type bias, reducing technical variation in duplicate samples, improving accuracy of measurements against known standards, and retention of biological signal. We find that RCP is statistically significantly better than unadjusted data or adjustment with alternative methods including SWAN and BMIQ. We incorporated the method into the R package ENmix, which is freely available from the Bioconductor website (https://www.bioconductor.org/packages/release/bioc/html/ENmix.html). niulg@ucmail.uc.edu Supplementary data are available at Bioinformatics online. Published by Oxford University Press 2016. This work is written by US Government employees and is in the public domain in the US.

An In-Vitro Evaluation and Comparison of Apical Sealing Ability of Three Different Obturation Technique - Lateral Condensation, Obtura II, and Thermafil.

PubMed

Emmanuel, Samson; Shantaram, Kulkarni; Sushil, Kumar C; Manoj, Likhitkar

2013-04-01

Success of non-surgical root canal treatment is predicted by meticulous cleaning and shaping of the root canal system, three-dimensional obturation and a well-fitting "leakage-free" coronal restoration. The techniques of obturation that are available have their own relative position in the historical development of filling techniques. Over the years, pitfalls with one technique have often led to the development of newer methods of obturation, along with the recognition that no one method of obturation may satisfy all clinical cases. A total of 120 extracted human permanent anterior maxillary and mandibular single rooted teeth were selected for the present study and divided into 3 groups based on the method of obturation technique. Following the preparation the patency at the apical foramen was confirmed by passing a file #15. After obturation of all three groups, teeth were immersed in 1% of aqueous methylene blue dye for a period of two weeks and then samples were subjected to spectrophotometric analysis. The present study was conducted to evaluate in vitro the spectrophotometric analysis to quantitatively analyze relative amount of dye penetration using lateral condensation (Group I), Obtura II (Group II ), Thermafil obturating technique (Group III) with ZOE sealer used in all groups. Teeth obturated with lateral condensation (Group I) shows mean value of 0.0243 and standard deviation of 0.0056. The Group II thermoplasticized injectable moulded Guttapercha (Obtura II) showed 0.0239 mean and standard deviation value of 0.0045 and Group III Thermafil obturation technique shows 0.0189 as mean value and 0.0035 standard deviation values. Following conclusion was drawn from the present study. Group III i.e., Thermafil obturating technique shows minimum mean apical dye penetration compared to Group II (ObturaII) and Group I (lateral condensation).Lateral condensation shows maximum mean apical dye penetration in all three groups.There is no significant difference between the apical dye penetration of lateral condensation and Obtura II. Obturation, lateral condensation, Obtura II, Thermafil, Spectrophotometer, dye penetration. How to cite this article: Samson E, Kulkarni S, Sushil K C, Likhitkar M. An In-Vitro Evaluation and Comparison of Apical Sealing Ability of Three Different Obturation Technique - Lateral Condensation, Obtura II, and Thermafil. J Int Oral Health 2013; 5(2):35-43.

Preparation and characterization of magnetic nanocomposite of Schiff base/silica/magnetite as a preconcentration phase for the trace determination of heavy metal ions in water, food and biological samples using atomic absorption spectrometry.

PubMed

Bagheri, Hasan; Afkhami, Abbas; Saber-Tehrani, Mohammad; Khoshsafar, Hosein

2012-08-15

A versatile and robust solid phase with both magnetic property and a very high adsorption capacity is presented on the basis of modification of iron oxide-silica magnetic particles with a newly synthesized Schiff base (Fe(3)O(4)/SiO(2)/L). The structure of the resulting product was confirmed by Fourier transform infrared (FT-IR) spectra, X-ray diffraction (XRD) spectrometry and transmission electron microscopy (TEM). We developed an efficient and cost-effective method for the preconcentration of trace amounts of Pb(II), Cd(II) and Cu(II) in environmental and biological samples using this novel magnetic solid phase. Prepared magnetic solid phase is an ideal support because it has a large surface area, good selectivity and can be easily retrieved from large volumes of aqueous solutions. The possible parameters affecting the enrichment were optimized. Under the optimal conditions, the method detection limit was 0.14, 0.19 and 0.12 μg L(-1) for Pb(II), Cd(II) and Cu(II) ions, respectively. The established method has been successfully applied to analyze real samples, and satisfactory results were obtained. All these indicated that this magnetic phase had a great potential in environmental and biological fields. Copyright © 2012 Elsevier B.V. All rights reserved.

Spatial organization of RNA polymerase II inside a mammalian cell nucleus revealed by reflected light-sheet superresolution microscopy.

PubMed

Zhao, Ziqing W; Roy, Rahul; Gebhardt, J Christof M; Suter, David M; Chapman, Alec R; Xie, X Sunney

2014-01-14

Superresolution microscopy based on single-molecule centroid determination has been widely applied to cellular imaging in recent years. However, quantitative imaging of the mammalian nucleus has been challenging due to the lack of 3D optical sectioning methods for normal-sized cells, as well as the inability to accurately count the absolute copy numbers of biomolecules in highly dense structures. Here we report a reflected light-sheet superresolution microscopy method capable of imaging inside the mammalian nucleus with superior signal-to-background ratio as well as molecular counting with single-copy accuracy. Using reflected light-sheet superresolution microscopy, we probed the spatial organization of transcription by RNA polymerase II (RNAP II) molecules and quantified their global extent of clustering inside the mammalian nucleus. Spatiotemporal clustering analysis that leverages on the blinking photophysics of specific organic dyes showed that the majority (>70%) of the transcription foci originate from single RNAP II molecules, and no significant clustering between RNAP II molecules was detected within the length scale of the reported diameter of "transcription factories." Colocalization measurements of RNAP II molecules equally labeled by two spectrally distinct dyes confirmed the primarily unclustered distribution, arguing against a prevalent existence of transcription factories in the mammalian nucleus as previously proposed. The methods developed in our study pave the way for quantitative mapping and stoichiometric characterization of key biomolecular species deep inside mammalian cells.

EPA Method 1615. Measurement of Enterovirus and Norovirus Occurrence in Water by Culture and RT-qPCR. II. Total Culturable Virus Assay

EPA Science Inventory

A standardized method is required when national studies on virus occurrence in environmental and drinking waters utilize multiple analytical laboratories. The U.S Environmental Protection Agency’s (USEPA) Method 1615 was developed with the goal of providing such a standard ...

Development and validation of an SPME-GC method for a degradation kinetics study of propiconazole I, propiconazole II and tebuconazole in blueberries in Concordia, the main production area of Argentina.

PubMed

Munitz, Martín S; Medina, María B; Montti, María I T

2017-05-01

An analytical method for the simultaneous determination of propiconazole isomers and tebuconazole residues in blueberries was developed using solid-phase microextraction (SPME) coupled to gas chromatography. Confirmation was performed by gas chromatography-mass spectrometry in selected-ion monitoring mode. The SPME fibre coating selected was CWX-DVB, and the pH was adjusted to 7 with NaOH. The method is selective with adequate precision and high accuracy and sensitivity. Recoveries ranged between 97.4% and 98.9% for all compounds; and detection and quantification limits were respectively 0.21 and 0.49 μg kg -1 for propiconazole I; 0.16 and 0.22 μg kg -1 for propiconazole II; and 0.16 and 0.48 μg kg -1 for tebuconazole. The degradation of these fungicides in blueberries followed first-order rate kinetics. The half-life times for flowering and fruit set applications were respectively 4.0 and 10.3 days for propiconazole I, 4.0 and 11.4 days for propiconazole II, and 3.5 and 12.4 days for tebuconazole.

Receiver operating characteristic analysis of prediction for gastric cancer development using serum pepsinogen and Helicobacter pylori antibody tests.

PubMed

Hamashima, Chisato; Sasazuki, Shizuka; Inoue, Manami; Tsugane, Shoichiro

2017-03-09

Chronic Helicobacter pylori infection plays a central role in the development of gastric cancer as shown by biological and epidemiological studies. The H. pylori antibody and serum pepsinogen (PG) tests have been anticipated to predict gastric cancer development. We determined the predictive sensitivity and specificity of gastric cancer development using these tests. Receiver operating characteristic analysis was performed, and areas under the curve were estimated. The predictive sensitivity and specificity of gastric cancer development were compared among single tests and combined methods using serum pepsinogen and H. pylori antibody tests. From a large-scale population-based cohort of over 100,000 subjects followed between 1990 and 2004, 497 gastric cancer subjects and 497 matched healthy controls were chosen. The predictive sensitivity and specificity were low in all single tests and combination methods. The highest predictive sensitivity and specificity were obtained for the serum PG I/II ratio. The optimal PG I/II cut-off values were 2.5 and 3.0. At a PG I/II cut-off value of 3.0, the sensitivity was 86.9% and the specificity was 39.8%. Even if three biomarkers were combined, the sensitivity was 97.2% and the specificity was 21.1% when the cut-off values were 3.0 for PG I/II, 70 ng/mL for PG I, and 10.0 U/mL for H. pylori antibody. The predictive accuracy of gastric cancer development was low with the serum pepsinogen and H. pylori antibody tests even if these tests were combined. To adopt these biomarkers for gastric cancer screening, a high specificity is required. When these tests are adopted for gastric cancer screening, they should be carefully interpreted with a clear understanding of their limitations.

Reaction mechanism of Ru(II) piano-stool complexes: umbrella sampling QM/MM MD study.

PubMed

Futera, Zdeněk; Burda, Jaroslav V

2014-07-15

Biologically relevant interactions of piano-stool ruthenium(II) complexes with ds-DNA are studied in this article by hybrid quantum mechanics-molecular mechanics (QM/MM) computational technique. The whole reaction mechanism is divided into three phases: (i) hydration of the [Ru(II) (η(6) -benzene)(en)Cl](+) complex, (ii) monoadduct formation between the resulting aqua-Ru(II) complex and N7 position of one of the guanines in the ds-DNA oligomer, and (iii) formation of the intrastrand Ru(II) bridge (cross-link) between two adjacent guanines. Free energy profiles of all the reactions are explored by QM/MM MD umbrella sampling approach where the Ru(II) complex and two guanines represent a quantum core, which is described by density functional theory methods. The combined QM/MM scheme is realized by our own software, which was developed to couple several quantum chemical programs (in this study Gaussian 09) and Amber 11 package. Calculated free energy barriers of the both ruthenium hydration and Ru(II)-N7(G) DNA binding process are in good agreement with experimentally measured rate constants. Then, this method was used to study the possibility of cross-link formation. One feasible pathway leading to Ru(II) guanine-guanine cross-link with synchronous releasing of the benzene ligand is predicted. The cross-linking is an exergonic process with the energy barrier lower than for the monoadduct reaction of Ru(II) complex with ds-DNA. Copyright © 2014 Wiley Periodicals, Inc.

High sensitive detection of copper II ions using D-penicillamine-coated gold nanorods based on localized surface plasmon resonance

NASA Astrophysics Data System (ADS)

Hong, Yoochan; Jo, Seongjae; Park, Joohyung; Park, Jinsung; Yang, Jaemoon

2018-05-01

In this paper, we describe the development of a nanoplasmonic biosensor based on the localized surface plasmon resonance (LSPR) effect that enables a sensitive and selective recognition of copper II ions. First, we fabricated the nanoplasmonics as LSPR substrates using gold nanorods (GNR) and the nano-adsorption method. The LSPR sensitivity of the nanoplasmonics was evaluated using various solvents with different refractive indexes. Subsequently, D-penicillamine (DPA)—a chelating agent of copper II ions—was conjugated to the surface of the GNR. The limit of detection (LOD) for the DPA-conjugated nanoplasmonics was 100 pM. Furthermore, selectivity tests were conducted using various divalent cations, and sensitivity tests were conducted on the nanoplasmonics under blood-like environments. Finally, the developed nanoplasmonic biosensor based on GNR shows great potential for the effective recognition of copper II ions, even in human blood conditions.

High sensitive detection of copper II ions using D-penicillamine-coated gold nanorods based on localized surface plasmon resonance.

PubMed

Hong, Yoochan; Jo, Seongjae; Park, Joohyung; Park, Jinsung; Yang, Jaemoon

2018-05-25

In this paper, we describe the development of a nanoplasmonic biosensor based on the localized surface plasmon resonance (LSPR) effect that enables a sensitive and selective recognition of copper II ions. First, we fabricated the nanoplasmonics as LSPR substrates using gold nanorods (GNR) and the nano-adsorption method. The LSPR sensitivity of the nanoplasmonics was evaluated using various solvents with different refractive indexes. Subsequently, D-penicillamine (DPA)-a chelating agent of copper II ions-was conjugated to the surface of the GNR. The limit of detection (LOD) for the DPA-conjugated nanoplasmonics was 100 pM. Furthermore, selectivity tests were conducted using various divalent cations, and sensitivity tests were conducted on the nanoplasmonics under blood-like environments. Finally, the developed nanoplasmonic biosensor based on GNR shows great potential for the effective recognition of copper II ions, even in human blood conditions.

Evidence-informed recommendations for constructing and disseminating messages supplementing the new Canadian Physical Activity Guidelines

PubMed Central

2013-01-01

Background Few validated guidelines exist for developing messages in health promotion practice. In clinical practice, the Appraisal of Guidelines, Research, and Evaluation II (AGREE II) Instrument is the international gold standard for guideline assessment, development, and reporting. In a case study format, this paper describes the application of the AGREE II principles to guide the development of health promotion guidelines for constructing messages to supplement the new Canadian Physical Activity Guidelines (CPAG) released in 2011. Methods The AGREE II items were modified to suit the objectives of developing messages that (1) clarify key components of the new CPAG and (2) motivate Canadians to meet the CPAG. The adapted AGREE II Instrument was used as a systematic guide for the recommendation development process. Over a two-day meeting, five workgroups (one for each CPAG – child, youth, adult, older adult – and one overarching group) of five to six experts (including behavior change, messaging, and exercise physiology researchers, key stakeholders, and end users) reviewed and discussed evidence for creating and targeting messages to supplement the new CPAG. Recommendations were summarized and reviewed by workgroup experts. The recommendations were pilot tested among end users and then finalized by the workgroup. Results The AGREE II was a useful tool in guiding the development of evidence-based specific recommendations for constructing and disseminating messages that supplement and increase awareness of the new CPAG (child, youth, adults, and older adults). The process also led to the development of sample messages and provision of a rationale alongside the recommendations. Conclusions To our knowledge, these are the first set of evidence-informed recommendations for constructing and disseminating messages supplementing physical activity guidelines. This project also represents the first application of international standards for guideline development (i.e., AGREE II) to the creation of practical recommendations specifically aimed to inform health promotion and public health practice. The messaging recommendations have the potential to increase the public health impact of evidence-based guidelines. PMID:23634998

Prescription of land-surface boundary conditions in GISS GCM 2: A simple method based on high-resolution vegetation data bases

NASA Technical Reports Server (NTRS)

Matthews, E.

1984-01-01

A simple method was developed for improved prescription of seasonal surface characteristics and parameterization of land-surface processes in climate models. This method, developed for the Goddard Institute for Space Studies General Circulation Model II (GISS GCM II), maintains the spatial variability of fine-resolution land-cover data while restricting to 8 the number of vegetation types handled in the model. This was achieved by: redefining the large number of vegetation classes in the 1 deg x 1 deg resolution Matthews (1983) vegetation data base as percentages of 8 simple types; deriving roughness length, field capacity, masking depth and seasonal, spectral reflectivity for the 8 types; and aggregating these surface features from the 1 deg x 1 deg resolution to coarser model resolutions, e.g., 8 deg latitude x 10 deg longitude or 4 deg latitude x 5 deg longitude.

Ontology-based configuration of problem-solving methods and generation of knowledge-acquisition tools: application of PROTEGE-II to protocol-based decision support.

PubMed

Tu, S W; Eriksson, H; Gennari, J H; Shahar, Y; Musen, M A

1995-06-01

PROTEGE-II is a suite of tools and a methodology for building knowledge-based systems and domain-specific knowledge-acquisition tools. In this paper, we show how PROTEGE-II can be applied to the task of providing protocol-based decision support in the domain of treating HIV-infected patients. To apply PROTEGE-II, (1) we construct a decomposable problem-solving method called episodic skeletal-plan refinement, (2) we build an application ontology that consists of the terms and relations in the domain, and of method-specific distinctions not already captured in the domain terms, and (3) we specify mapping relations that link terms from the application ontology to the domain-independent terms used in the problem-solving method. From the application ontology, we automatically generate a domain-specific knowledge-acquisition tool that is custom-tailored for the application. The knowledge-acquisition tool is used for the creation and maintenance of domain knowledge used by the problem-solving method. The general goal of the PROTEGE-II approach is to produce systems and components that are reusable and easily maintained. This is the rationale for constructing ontologies and problem-solving methods that can be composed from a set of smaller-grained methods and mechanisms. This is also why we tightly couple the knowledge-acquisition tools to the application ontology that specifies the domain terms used in the problem-solving systems. Although our evaluation is still preliminary, for the application task of providing protocol-based decision support, we show that these goals of reusability and easy maintenance can be achieved. We discuss design decisions and the tradeoffs that have to be made in the development of the system.

Job monitoring on DIRAC for Belle II distributed computing

NASA Astrophysics Data System (ADS)

Kato, Yuji; Hayasaka, Kiyoshi; Hara, Takanori; Miyake, Hideki; Ueda, Ikuo

2015-12-01

We developed a monitoring system for Belle II distributed computing, which consists of active and passive methods. In this paper we describe the passive monitoring system, where information stored in the DIRAC database is processed and visualized. We divide the DIRAC workload management flow into steps and store characteristic variables which indicate issues. These variables are chosen carefully based on our experiences, then visualized. As a result, we are able to effectively detect issues. Finally, we discuss the future development for automating log analysis, notification of issues, and disabling problematic sites.

Launch Vehicle Ascent Trajectory Simulation Using the Program to Optimize Simulated Trajectories II (POST2)

NASA Technical Reports Server (NTRS)

Lugo, Rafael A.; Shidner, Jeremy D.; Powell, Richard W.; Marsh, Steven M.; Hoffman, James A.; Litton, Daniel K.; Schmitt, Terri L.

2017-01-01

The Program to Optimize Simulated Trajectories II (POST2) has been continuously developed for over 40 years and has been used in many flight and research projects. Recently, there has been an effort to improve the POST2 architecture by promoting modularity, flexibility, and ability to support multiple simultaneous projects. The purpose of this paper is to provide insight into the development of trajectory simulation in POST2 by describing methods and examples of various improved models for a launch vehicle liftoff and ascent.

Biotechnological applications of mobile group II introns and their reverse transcriptases: gene targeting, RNA-seq, and non-coding RNA analysis.

PubMed

Enyeart, Peter J; Mohr, Georg; Ellington, Andrew D; Lambowitz, Alan M

2014-01-13

Mobile group II introns are bacterial retrotransposons that combine the activities of an autocatalytic intron RNA (a ribozyme) and an intron-encoded reverse transcriptase to insert site-specifically into DNA. They recognize DNA target sites largely by base pairing of sequences within the intron RNA and achieve high DNA target specificity by using the ribozyme active site to couple correct base pairing to RNA-catalyzed intron integration. Algorithms have been developed to program the DNA target site specificity of several mobile group II introns, allowing them to be made into 'targetrons.' Targetrons function for gene targeting in a wide variety of bacteria and typically integrate at efficiencies high enough to be screened easily by colony PCR, without the need for selectable markers. Targetrons have found wide application in microbiological research, enabling gene targeting and genetic engineering of bacteria that had been intractable to other methods. Recently, a thermostable targetron has been developed for use in bacterial thermophiles, and new methods have been developed for using targetrons to position recombinase recognition sites, enabling large-scale genome-editing operations, such as deletions, inversions, insertions, and 'cut-and-pastes' (that is, translocation of large DNA segments), in a wide range of bacteria at high efficiency. Using targetrons in eukaryotes presents challenges due to the difficulties of nuclear localization and sub-optimal magnesium concentrations, although supplementation with magnesium can increase integration efficiency, and directed evolution is being employed to overcome these barriers. Finally, spurred by new methods for expressing group II intron reverse transcriptases that yield large amounts of highly active protein, thermostable group II intron reverse transcriptases from bacterial thermophiles are being used as research tools for a variety of applications, including qRT-PCR and next-generation RNA sequencing (RNA-seq). The high processivity and fidelity of group II intron reverse transcriptases along with their novel template-switching activity, which can directly link RNA-seq adaptor sequences to cDNAs during reverse transcription, open new approaches for RNA-seq and the identification and profiling of non-coding RNAs, with potentially wide applications in research and biotechnology.

Development of Modern Methods for Determination of Stabilizers in Propellants

DTIC Science & Technology

1996-04-01

powder will! . gtve information Jbout the history of this powder and an indication of its future: usefulness. In othdrs words, the determination of...been excluded in Tables I and II. According to Table I, in order to develop an HPLC method for DPA-stabilized powders , the products that should be... powders were determined by each country using its own HPLC method . The results are given in Table XVI. As indicated, the agreement between the two

Application of an enzyme immunoassay for the quantitative determination of azo dye (Orange II) in food products.

PubMed

Xue, Huyin; Xing, Yue; Yin, Yongmei; Zhang, Taichang; Zhang, Bo; Zhang, Yu; Song, Pei; Tian, Xi; Xu, Yinghui; Wang, Peng; Meng, Meng; Xi, Rimo

2012-01-01

This paper reports the preparation of polyclonal antibodies against a synthetic azo dye, Orange II, and the development of an indirect ELISA to detect Orange II in foods. The sulfonic group of Orange II was modified and linked with carrier protein to synthesise an artificial antigen. Based on the checkerboard titration, the method showed excellent sensitivity (IC₅₀ = 0.61 ng g⁻¹) to Orange II in the linear range of 0.05-10 ng g⁻¹. The antibody had little cross-reactivity with Chromotrope FB, Gardenia Yellow, Ponceau 4R, Sunset Yellow and Sudan dyes. The ELISA had limits of detection (LOD) of 0.22, 0.97 and 0.74 ng g⁻¹ in chilli powder, chilli oil and braised pork, respectively. The limits of quantification (LOQ) of the assay were 0.91 ng g⁻¹ in chilli powder, 1.48 ng g⁻¹ in chilli oil and 1.10 ng g⁻¹ in braised pork. For food products fortified with 1-10 ng g⁻¹ Orange II, the inter- and intra-assay variations were all less than 24.0% and 18.0%, respectively. Therefore, the proposed test could be used as a rapid screening method for Orange II detection in food samples.

The Helicity Injected Torus Program

NASA Astrophysics Data System (ADS)

Jarboe, T. R.; Nelson, B. A.; Jewell, P. D.; Liptac, J. E.; McCollam, K. J.; Raman, R.; Redd, A. J.; Rogers, J. A.; Sieck, P. E.; Shumlak, U.; Smith, R. J.; Nagata, M.; Uyama, T.

1999-11-01

The Helicity Injected Torus--II (HIT--II) spherical torus is capable of both Coaxial Helicity Injection (CHI) and transformer action current drive. HIT--II has a major radius R = 0.3, minor radius a = 0.2, aspect ratio A = R/a = 1.5, with an on axis magnetic field of up to Bo = 0.67 T. HIT--II provides equilibrium control, CHI flux boundary conditions, and transformer action using 28 poloidal field coils, using active flux feedback control. HIT--II has driven up to 200 kA of plasma current, using either CHI or transformer drive. An overview and recent results of the HIT--II program will be presented. The development of a locked-electron current drive model for HIT and HIT--II has led to the design of a constant inductive helicity injection method for spherical torii. This method is incorporated in the design of the Helicity Injected Torus -- Steady Inductive (HIT-- SI)(T.R. Jarboe, Fusion Technology, 36) (1), p. 85, 1999 experiment. HIT--SI can form a high-beta spheromak, a low aspect ratio RFP, or a spherical tokamak in a steady-state manner without using electrodes. The HIT--SI design and methodology will be presented.

Synergistic extraction and spectrophotometric determination of copper(II) using 1-(2',4'-dinitro aminophenyl)-4,4,6-trimethyl-1,4-dihydropyrimidine-2-thiol: Analysis of alloys, pharmaceuticals and biological samples

NASA Astrophysics Data System (ADS)

Kamble, Ganesh S.; Kolekar, Sanjay S.; Anuse, Mansing A.

2011-05-01

A simple and selective spectrophotometric method was developed for the determination of copper(II) with 1-(2',4'-dinitro aminophenyl)-4,4,6-trimethyl-1,4-dihydropyrimidine-2-thiol [2',4'-dinitro APTPT] as a chromogenic reagent. The procedure was based on the synergistic extraction of copper(II) with 2',4'-dinitro APTPT in the presence of 0.5 mol L -1 pyridine to give green colored ternary complex of a molar ratio 1:2:2 (M:L:Py) in the pH range 8.7-10.5. It exhibits a maximum absorption of colored complex at 445 nm and 645 nm in chloroform against the reagent blank. Beer's law was followed in the concentration range 10-80 μg mL -1 of copper(II) and optimum range of 20-70 μg mL -1 the metal as evaluated from Ringbom's plot. The molar absorptivity and Sandell's sensitivity of copper(II)-2',4'-dinitro APTPT-pyridine complex in chloroform are 0.87 × 10 3 L mol -1 cm -1 and 0.072 μg cm -2, respectively. The interfering effects of various cations and anions were also studied, and use of suitable masking agents enhances the selectivity of the method. The proposed method is rapid, reproducible and successfully applied for the determination of copper(II) in binary and synthetic mixtures, alloys, pharmaceutical formulations, environmental and fertilizer samples. Comparison of the results with those obtained using an atomic absorption spectrophotometer also tested the validity of the method.

Wind Assessment for Aerial Payload Delivery Systems Using GPS and IMU Sensors

DTIC Science & Technology

2016-09-01

post- processing of the resultant test data were the research methods used in development of this thesis . Ultimately, this thesis presents two models ...processing of the resultant test data were the research methods used in development of this thesis . Ultimately, this thesis presents two models for winds...7  E .  THESIS OBJECTIVE AND ORGANIZATION ................................. 7  II.  BLIZZARD SYSTEM COMPONENTS

Designing of interferon-gamma inducing MHC class-II binders

PubMed Central

2013-01-01

Background The generation of interferon-gamma (IFN-γ) by MHC class II activated CD4+ T helper cells play a substantial contribution in the control of infections such as caused by Mycobacterium tuberculosis. In the past, numerous methods have been developed for predicting MHC class II binders that can activate T-helper cells. Best of author’s knowledge, no method has been developed so far that can predict the type of cytokine will be secreted by these MHC Class II binders or T-helper epitopes. In this study, an attempt has been made to predict the IFN-γ inducing peptides. The main dataset used in this study contains 3705 IFN-γ inducing and 6728 non-IFN-γ inducing MHC class II binders. Another dataset called IFNgOnly contains 4483 IFN-γ inducing epitopes and 2160 epitopes that induce other cytokine except IFN-γ. In addition we have alternate dataset that contains IFN-γ inducing and equal number of random peptides. Results It was observed that the peptide length, positional conservation of residues and amino acid composition affects IFN-γ inducing capabilities of these peptides. We identified the motifs in IFN-γ inducing binders/peptides using MERCI software. Our analysis indicates that IFN-γ inducing and non-inducing peptides can be discriminated using above features. We developed models for predicting IFN-γ inducing peptides using various approaches like machine learning technique, motifs-based search, and hybrid approach. Our best model based on the hybrid approach achieved maximum prediction accuracy of 82.10% with MCC of 0.62 on main dataset. We also developed hybrid model on IFNgOnly dataset and achieved maximum accuracy of 81.39% with 0.57 MCC. Conclusion Based on this study, we have developed a webserver for predicting i) IFN-γ inducing peptides, ii) virtual screening of peptide libraries and iii) identification of IFN-γ inducing regions in antigen (http://crdd.osdd.net/raghava/ifnepitope/). Reviewers This article was reviewed by Prof Kurt Blaser, Prof Laurence Eisenlohr and Dr Manabu Sugai. PMID:24304645

Removal of Zn(II) from electroplating effluent using yeast biofilm formed on gravels: batch and column studies

PubMed Central

2014-01-01

Background Present study deals with the removal of Zn(II) ions from effluent using yeast biofilm formed on gravels. Methods The biofilm forming ability of Candida rugosa and Cryptococcus laurentii was evaluated using XTT (2,3-bis[2-methoxy-4-nitro-5-sulfophenyl]-2H-tetrazolium-5-carboxanilide) reduction assay and monitored by scanning electron microscopy (SEM), and Confocal laser scanning microscopy (CLSM). Copious amount of extracellular polymeric substances (EPS) produced by yeast species was quantified and characterized by Fourier transform infrared spectroscopy (FT-IR). Results Yeast biofilm formed on gravels by C. rugosa and C. laurentii showed 88% and 74.2% removal of Zn(II) ions respectively in batch mode. In column mode, removal of Zn(II) ions from real effluent was found to be 95.29% by C. rugosa biofilm formed on gravels. Conclusion The results of the present study showed that there is a scope to develop a cost effective method for the efficient removal of Zn(II) from effluent using gravels coated with yeast biofilm. PMID:24397917

40 CFR 35.290 - Purpose.

Code of Federal Regulations, 2013 CFR

2013-07-01

... construction types); (ii) Development of public information and education materials concerning radon assessment... accordance with § 35.298(d); (viii) Development of a data storage and management system for information... methods and technologies as approved by EPA, including State participation in the EPA Home Evaluation...

40 CFR 35.290 - Purpose.

Code of Federal Regulations, 2011 CFR

2011-07-01

... construction types); (ii) Development of public information and education materials concerning radon assessment... accordance with § 35.298(d); (viii) Development of a data storage and management system for information... methods and technologies as approved by EPA, including State participation in the EPA Home Evaluation...

40 CFR 35.290 - Purpose.

Code of Federal Regulations, 2012 CFR

2012-07-01

... construction types); (ii) Development of public information and education materials concerning radon assessment... accordance with § 35.298(d); (viii) Development of a data storage and management system for information... methods and technologies as approved by EPA, including State participation in the EPA Home Evaluation...

QUARTERLY TECHNICAL PROGRESS REPORT, JULY, AUGUST, SEPTEMBER 1966.

DTIC Science & Technology

Contents: Circuit research program; Hardware systems research; Software systems research program; Numerical methods, computer arithmetic and...artificial languages; Library automation; Illiac II service , use, and program development; IBM service , use, and program development; Problem specifications; Switching theory and logical design; General laboratory information.

Rapid and sensitive detection of canine distemper virus by one-tube reverse transcription-insulated isothermal polymerase chain reaction.

PubMed

Wilkes, Rebecca P; Tsai, Yun-Long; Lee, Pei-Yu; Lee, Fu-Chun; Chang, Hsiao-Fen Grace; Wang, Hwa-Tang Thomas

2014-09-09

Canine distemper virus (CDV) has been associated with outbreaks of canine infectious respiratory disease in shelters and boarding kennel environments. POCKITTM Nucleic Acid Analyzer is a field-deployable device capable of generating automatically interpreted insulated isothermal polymerase chain reaction (iiPCR) results from extracted nucleic acid within one hour. In this study, reverse transcription iiPCR (RT-iiPCR) was developed to facilitate point-of-need diagnosis of CDV infection. Analytical sensitivity (limit of detection 95%) of the established CDV RT-iiPCR was about 11 copies of in vitro transcribed RNA per reaction. CDV RT-iiPCR generated positive signals from CDV, but not Bordetella bronchiseptica, canine parvovirus, canine herpesvirus, canine adenovirus 2, canine influenza virus (subtype H3N8), canine parainfluenza virus, and canine respiratory coronavirus. To evaluate accuracy of the established reaction in canine distemper clinical diagnosis, 110 specimens from dogs, raccoons, and foxes suspected with CDV infection were tested simultaneously by CDV RT-iiPCR and real-time RT-PCR. CDV RT-iiPCR demonstrated excellent sensitivity (100%) and specificity (100%), compared to real-time RT-PCR. The results indicated an excellent correlation between RT-iiPCR and a reference real time RT-PCR method. Working in a lyophilized format, the established method has great potential to be used for point-of-care diagnosis of canine distemper in animals, especially in resource-limited facilities.

Calculation of effective plutonium cross sections and check against the oscillation experiment CESAR-II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schaal, H.; Bernnat, W.

1987-10-01

For calculations of high-temperature gas-cooled reactors with low-enrichment fuel, it is important to know the plutonium cross sections accurately. Therefore, a calculational method was developed, by which the plutonium cross-section data of the ENDF/B-IV library can be examined. This method uses zero- and one-dimensional neutron transport calculations to collapse the basic data into one-group cross sections, which then can be compared with experimental values obtained from integral tests. For comparison the data from the critical experiment CESAR-II of the Centre d'Etudes Nucleaires, Cadarache, France, were utilized.

Enantioselective Synthesis of α-Mercapto-β-amino Esters via Rh(II)/Chiral Phosphoric Acid-Cocatalyzed Three-Component Reaction of Diazo Compounds, Thiols, and Imines.

PubMed

Xiao, Guolan; Ma, Chaoqun; Xing, Dong; Hu, Wenhao

2016-12-02

An enantioselective method for the synthesis of α-mercapto-β-amino esters has been developed via a rhodium(II)/chiral phosphoric acid-cocatalyzed three-component reaction of diazo compounds, thiols, and imines. This transformation is proposed to proceed through enantioselective trapping of the sulfonium ylide intermediate generated in situ from the diazo compound and thiol by the phosphoric acid-activated imine. With this method, a series of α-mercapto-β-amino esters were obtained in good yields with moderate to good stereoselectivities.

An insulated isothermal PCR method on a field-deployable device for rapid and sensitive detection of canine parvovirus type 2 at points of need.

PubMed

Wilkes, Rebecca P; Lee, Pei-Yu A; Tsai, Yun-Long; Tsai, Chuan-Fu; Chang, Hsiu-Hui; Chang, Hsiao-Fen G; Wang, Hwa-Tang T

2015-08-01

Canine parvovirus type 2 (CPV-2), including subtypes 2a, 2b and 2c, causes an acute enteric disease in both domestic and wild animals. Rapid and sensitive diagnosis aids effective disease management at points of need (PON). A commercially available, field-deployable and user-friendly system, designed with insulated isothermal PCR (iiPCR) technology, displays excellent sensitivity and specificity for nucleic acid detection. An iiPCR method was developed for on-site detection of all circulating CPV-2 strains. Limit of detection was determined using plasmid DNA. CPV-2a, 2b and 2c strains, a feline panleukopenia virus (FPV) strain, and nine canine pathogens were tested to evaluate assay specificity. Reaction sensitivity and performance were compared with an in-house real-time PCR using serial dilutions of a CPV-2b strain and 100 canine fecal clinical samples collected from 2010 to 2014, respectively. The 95% limit of detection of the iiPCR method was 13 copies of standard DNA and detection limits for CPV-2b DNA were equivalent for iiPCR and real-time PCR. The iiPCR reaction detected CPV-2a, 2b and 2c and FPV. Non-targeted pathogens were not detected. Test results of real-time PCR and iiPCR from 99 fecal samples agreed with each other, while one real-time PCR-positive sample tested negative by iiPCR. Therefore, excellent agreement (k = 0.98) with sensitivity of 98.41% and specificity of 100% in detecting CPV-2 in feces was found between the two methods. In conclusion, the iiPCR system has potential to serve as a useful tool for rapid and accurate PON, molecular detection of CPV-2. Copyright © 2015 The Authors. Published by Elsevier B.V. All rights reserved.

Advances in variable selection methods II: Effect of variable selection method on classification of hydrologically similar watersheds in three Mid-Atlantic ecoregions

EPA Science Inventory

Hydrological flow predictions in ungauged and sparsely gauged watersheds use regionalization or classification of hydrologically similar watersheds to develop empirical relationships between hydrologic, climatic, and watershed variables. The watershed classifications may be based...

Repair of steel beam/girder ends with ultra high-strength concrete - phase II.

DOT National Transportation Integrated Search

2016-01-01

A novel repair method has been developed at the University of Connecticut for corroded steel bridge girder : ends. The repair method consists of encasing the corroded steel area with UHPC. The UHPC panel is bonded : to the steel girder using headed s...

Determination of Trace Elements in Uranium by HPLC-ID-ICP-MS: NTNFC Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Manard, Benjamin Thomas; Wylie, Ernest Miller II; Xu, Ning

This report covers the FY 16 effort for the HPLC-ID-ICP-MS methodology 1) sub-method validation for the group I&II elements, 2) sub-method stood-up and validation for REE, 3) sub-method development for the transition element, and 4) completion of a comprehensive SOP for three families of elements.

Rural Development Research: A Foundation for Policy. Contributions in Economics and Economic History, Number 170.

ERIC Educational Resources Information Center

Rowley, Thomas D., Ed.; And Others

This book addresses the need for research information that can be used as a foundation for rural development policy. Part I deals with the four components of rural development: education (human capital), entrepreneurship, physical infrastructure, and social infrastructure. Part II examines analytic methods of measuring rural development efforts,…

Synthesis and strong photooxidation power of a supramolecular hybrid comprising a polyoxometalate and Ru(II) polypyridyl complex with zinc(II).

PubMed

Ohashi, Kenji; Takeda, Hiroyuki; Koike, Kazuhide; Ishitani, Osamu

2015-01-01

A novel method for constructing supramolecular hybrids composed of polyoxometalates and photofunctional metal complexes was developed. A Ru(II) complex with phosphonate groups (RuP) strongly interacted with Zn(II) to afford a 2 : 1 trinuclear metal complex ([(RuP)2Zn](3+)). In dimethylsulfoxide, [(RuP)2Zn](3+) strongly interacted with a Keggin-type heteropolyoxometalate (Si-WPOM) to form a 1 : 1 hybrid ([(RuP)2Zn]-POM). Irradiation of [(RuP)2Zn]-POM in the presence of diethanolamine caused rapid accumulation of the one-electron reduced hybrid with a quantum yield of 0.99.

Can Depression be Diagnosed by Response to Mother's Face? A Personalized Attachment-Based Paradigm for Diagnostic fMRI

PubMed Central

Zhang, Xian; Yaseen, Zimri S.; Galynker, Igor I.; Hirsch, Joy; Winston, Arnold

2011-01-01

Objective Objective measurement of depression remains elusive. Depression has been associated with insecure attachment, and both have been associated with changes in brain reactivity in response to viewing standard emotional and neutral faces. In this study, we developed a method to calculate predicted scores for the Beck Depression Inventory II (BDI-II) using personalized stimuli: fMRI imaging of subjects viewing pictures of their own mothers. Methods 28 female subjects ages 18–30 (14 healthy controls and 14 unipolar depressed diagnosed by MINI psychiatric interview) were scored on the Beck Depression Inventory II (BDI-II) and the Adult Attachment Interview (AAI) coherence of mind scale of global attachment security. Subjects viewed pictures of Mother (M), Friend (F) and Stranger (S), during functional magnetic resonance imaging (fMRI). Using a principal component regression method (PCR), a predicted Beck Depression Inventory II (BDI-II) score was obtained from activity patterns in the paracingulate gyrus (Brodmann area 32) and compared to clinical diagnosis and the measured BDI-II score. The same procedure was performed for AAI coherence of mind scores. Results Activity patterns in BA-32 identified depressed subjects. The categorical agreement between the derived BDI-II score (using the standard clinical cut-score of 14 on the BDI-II) and depression diagnosis by MINI psychiatric interview was 89%, with sensitivity 85.7% and specificity 92.8%. Predicted and measured BDI-II scores had a correlation of 0.55. Prediction of attachment security was not statistically significant. Conclusions Brain activity in response to viewing one's mother may be diagnostic of depression. Functional magnetic resonance imaging using personalized paradigms has the potential to provide objective assessments, even when behavioral measures are not informative. Further, fMRI based diagnostic algorithms may enhance our understanding of the neural mechanisms of depression by identifying distinctive neural features of the illness. PMID:22180777

Indirect spectrophotometric determination of sodium ceftriaxone with n-propyl alcohol-ammonium sulfate-water system by extraction flotation of copper(II).

PubMed

Zhao, Wei; Zhang, Yan; Li, Quanmin

2008-05-01

Although the determination methods of sodium ceftriaxone has been increasingly reported, these methods have their inherent limits preventing them from being broadly applied in common laboratories. In order to circumvent this problem, a rapid and simple method for the indirect spectrophotometric determination of sodium ceftriaxone is reported. Sodium ceftriaxone was degraded completely in the presence of 0.20 mol/l sodium hydroxide in boiling water bath for 20 min. The thiol group (-SH) of the degradation product (I) of sodium ceftriaxone could reduce cupric to cuprous ions, and the resulting which was precipitated with the thiol group (-SH) of the degradation product (II) at pH 4.0. By determining the residual amount of copper (II), the indirect determination of sodium ceftriaxone can be achieved. Standard curve of sodium ceftriaxone versus the flotation yield of copper(II) showed that sodium ceftriaxone could be determined in low concentrations. The linear range of sodium ceftriaxone was 0.70-32 microg/ml and the detection limit evaluated by calibration curve (3sigma/k) was found to be 0.60 microg/ml. A simple and efficient method was developed and it has been successfully applied to the determination of sodium ceftriaxone in human serum and urine samples, respectively. It is expected that this method will find broad applications in the detection of cephalosporin derivatives with similar structure.

I/O Router Placement and Fine-Grained Routing on Titan to Support Spider II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ezell, Matthew A; Dillow, David; Oral, H Sarp

2014-01-01

The Oak Ridge Leadership Computing Facility (OLCF) introduced the concept of Fine-Grained Routing in 2008 to improve I/O performance between the Jaguar supercomputer and Spider, OLCF s center-wide Lustre file system. Fine-grained routing organizes I/O paths to minimize congestion. Jaguar has since been upgraded to Titan, providing more than a ten-fold improvement in peak performance. To support the center s increased computational capacity and I/O demand, the Spider file system has been replaced with Spider II. Building on the lessons learned from Spider, an improved method for placing LNET routers was developed and implemented for Spider II. The fine-grained routingmore » scripts and configuration have been updated to provide additional optimizations and better match the system setup. This paper presents a brief history of fine-grained routing at OLCF, an introduction to the architectures of Titan and Spider II, methods for placing routers in Titan, and details about the fine-grained routing configuration.« less

Simultaneous preconcentration of cadmium and lead in water samples with silica gel and determination by flame atomic absorption spectrometry.

PubMed

Xu, Hongbo; Wu, Yun; Wang, Jian; Shang, Xuewei; Jiang, Xiaojun

2013-12-01

A new method that utilizes pretreated silica gel as an adsorbent has been developed for simultaneous preconcentration of trace Cd(II) and Pb(II) prior to the measurement by flame atomic absorption spectrometry. The effects of pH, the shaking time, the elution condition and the coexisting ions on the separation/preconcentration conditions of analytes were investigated. Under optimized conditions, the static adsorption capacity of Cd(II) and Pb(II) were 45.5 and 27.1mg/g, the relative standard deviations were 3.2% and 1.7% (for n = 11), and the limits of detection obtained were 4.25 and 0.60 ng/mL, respectively. The method was validated by analyzing the certified reference materials GBW 07304a (stream sediment) and successfully applied to the analysis of various treated wastewater samples with satisfactory results. Copyright © 2013 The Research Centre for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

Insights into colour-tuning of chlorophyll optical response in green plants.

PubMed

Jornet-Somoza, Joaquim; Alberdi-Rodriguez, Joseba; Milne, Bruce F; Andrade, Xavier; Marques, Miguel A L; Nogueira, Fernando; Oliveira, Micael J T; Stewart, James J P; Rubio, Angel

2015-10-28

First-principles calculations within the framework of real-space time-dependent density functional theory have been performed for the complete chlorophyll (Chl) network of the light-harvesting complex from green plants, LHC-II. A local-dipole analysis method developed for this work has made possible the studies of the optical response of individual Chl molecules subjected to the influence of the remainder of the chromophore network. The spectra calculated using our real-space TDDFT method agree with previous suggestions that weak interaction with the protein microenvironment should produce only minor changes in the absorption spectrum of Chl chromophores in LHC-II. In addition, relative shifting of Chl absorption energies leads the stromal and lumenal sides of LHC-II to absorb in slightly different parts of the visible spectrum providing greater coverage of the available light frequencies. The site-specific alterations in Chl excitation energies support the existence of intrinsic energy transfer pathways within the LHC-II complex.

[Study on solid phase extraction spectrophotometric determination of zinc with 2-(2-quinolylazo)-5-dimthylaminophenol].

PubMed

Zhou, Shi-ping; Duan, Chang-qun; Liu, Hong-cheng; Hu, Qiu-fen

2005-10-01

A highly sensitive, selective and rapid method for the determination of zinc based on the rapid reaction of zinc(II) with 2-(2-quinolylazo)-5-dimthylaminophenol (QADMAP) and the solid phase extraction of zinc ion with anion exchange resin cartridge was developed. In the presence of pH 8.5 buffer solution and Triton X-100 medium, QADMAP can react with zinc(II) to form a stable 2 :1 complex (QADMAP:Zn(II)). The molar absorptivity is 1.22 x 10(5)L x moL(-1) x cm(-1) at 590 nm. Beer's law is obeyed in the range of 0-1.0 microg x mL(-1). The zinc ions in the samples can be enriched and separated by solid phase extraction with anion exchange resincartridge. Testing results show that recovery for zinc(II) was from 95% to 104%, and RSD was below 3%. This method was applied to the determination of zinc in water and food with good results.

Insights into colour-tuning of chlorophyll optical response in green plants

DOE PAGES

Jornet-Somoza, Joaquim; Alberdi-Rodriguez, Joseba; Milne, Bruce F.; ...

2015-07-17

Here, we performed first-principles calculations within the framework of real-space time-dependent density functional theory for the complete chlorophyll (Chl) network of the light-harvesting complex from green plants, LHC-II. A local-dipole analysis method developed for this work has made possible the studies of the optical response of individual Chl molecules subjected to the influence of the remainder of the chromophore network. The spectra calculated using our real-space TDDFT method agree with previous suggestions that weak interaction with the protein microenvironment should produce only minor changes in the absorption spectrum of Chl chromophores in LHC-II. In addition, relative shifting of Chl absorptionmore » energies leads the stromal and lumenal sides of LHC-II to absorb in slightly different parts of the visible spectrum providing greater coverage of the available light frequencies. The site-specific alterations in Chl excitation energies support the existence of intrinsic energy transfer pathways within the LHC-II complex.« less

[Efficiency of combined methods of hemorroid treatment using hal-rar and laser destruction].

PubMed

Rodoman, G V; Kornev, L V; Shalaeva, T I; Malushenko, R N

2017-01-01

To develop the combined method of treatment of hemorrhoids with arterial ligation under Doppler control and laser destruction of internal and external hemorrhoids. The study included 100 patients with chronic hemorrhoids stage II and III. Combined method of HAL-laser was used in study group, HAL RAR-technique in control group 1 and closed hemorrhoidectomy with linear stapler in control group 2. Сomparative evaluation of results in both groups was performed. Combined method overcomes the drawbacks of traditional surgical treatment and limitations in external components elimination which are inherent for HAL-RAR. Moreover, it has a higher efficiency in treating of hemorrhoids stage II-III compared with HAL-RAR and is equally safe and well tolerable for patients. This method does not increase the risk of recurrence, reduces incidence of complications and time of disability.

Synthesis, characterization and application of a new chelating resin for solid phase extraction, preconcentration and determination of trace metals in some dairy samples by flame atomic absorption spectrometry.

PubMed

Daşbaşı, Teslima; Saçmacı, Şerife; Çankaya, Nevin; Soykan, Cengiz

2016-11-15

In this study, a simple and rapid solid phase extraction/preconcentration procedure was developed for determination of Cd(II), Co(II), Cr(III), Cu(II), Fe(III), Mn(II), Pb(II), and Zn(II) trace metals by flame atomic absorption spectrometry (FAAS). A new chelating resin, poly(N-cyclohexylacrylamide-co-divinylbenzene-co-2-acrylamido-2-methyl-1-propanesulfonic acid) (NCA-co-DVB-co-AMPS) (hereafter CDAP) was synthesized and characterized. The influences of the analytical parameters such as pH of the sample solution, type and concentration of eluent, flow rates of the sample and eluent, volume of the sample and eluent, amount of chelating resin, and interference of ions were examined. The limit of detection (LOD) of analytes were found (3s) to be in the range of 0.65-1.90μgL(-1). Preconcentration factor (PF) of 200 and the relative standard deviation (RSD) of ⩽2% were achieved (n=11). The developed method was applied for determination of analytes in some dairy samples and certified reference materials. Copyright © 2016 Elsevier Ltd. All rights reserved.

Unipolar distributions of junctional Myosin II identify cell stripe boundaries that drive cell intercalation throughout Drosophila axis extension

PubMed Central

Tetley, Robert J; Blanchard, Guy B; Fletcher, Alexander G; Adams, Richard J; Sanson, Bénédicte

2016-01-01

Convergence and extension movements elongate tissues during development. Drosophila germ-band extension (GBE) is one example, which requires active cell rearrangements driven by Myosin II planar polarisation. Here, we develop novel computational methods to analyse the spatiotemporal dynamics of Myosin II during GBE, at the scale of the tissue. We show that initial Myosin II bipolar cell polarization gives way to unipolar enrichment at parasegmental boundaries and two further boundaries within each parasegment, concomitant with a doubling of cell number as the tissue elongates. These boundaries are the primary sites of cell intercalation, behaving as mechanical barriers and providing a mechanism for how cells remain ordered during GBE. Enrichment at parasegment boundaries during GBE is independent of Wingless signaling, suggesting pair-rule gene control. Our results are consistent with recent work showing that a combinatorial code of Toll-like receptors downstream of pair-rule genes contributes to Myosin II polarization via local cell-cell interactions. We propose an updated cell-cell interaction model for Myosin II polarization that we tested in a vertex-based simulation. DOI: http://dx.doi.org/10.7554/eLife.12094.001 PMID:27183005

Determination of pharmacokinetics of chrysin and its conjugates in wild-type FVB and Bcrp1 knockout mice using a validated LC-MS/MS method.

PubMed

Ge, Shufan; Gao, Song; Yin, Taijun; Hu, Ming

2015-03-25

Chrysin, a flavone found in many plants, is also available as a dietary supplement because of its reported anticancer activities. However, its bioavailability is very poor due to extensive phase II metabolism. The purpose of this study was to develop an UPLC-MS/MS method to simultaneously quantify chrysin and its phase II metabolites, and to determine its pharmacokinetics in FVB wild-type and Bcrp knockout (Bcrp1 -/-) mice. In addition, the role of BCRP in chrysin phase II disposition was further investigated in Caco-2 cells. The results showed that our sensitive and reproducible UPLC-MS/MS method was successfully applied to the pharmacokinetic study of chrysin in wild-type and Bcrp1 (-/-) FVB mice after oral administration (20 mg/kg). Although there was no significant change in systemic exposure of chrysin and its metabolites, it was found that the Tmax for chrysin glucuronide was significantly shorter (p < 0.01) in Bcrp1-deficient mice. Furthermore, it was shown that inhibition of BCRP by Ko143 significantly reduced the efflux of chrysin sulfate in Caco-2 cells. In conclusion, BCRP had significant but less than expected impact on pharmacokinetics of chrysin and its conjugates, which were determined using a newly developed and validated LC-MS/MS method.

Air Quality Management Alternatives: United States Air Force Firefighter Training Facilities

DTIC Science & Technology

1988-01-01

Pollution at LAX, JFK , and ORD," Impact of Aircraft Emissions on Air Quality in the Vicinity of Airports , Volume II, FAA-EE-80-09B, Federal...developed and applied . This method enabled fire prevention, and environmental management experts and professionals to provide data, opinions, and to...methodology utilizing questionnaires, interviews, and site visits is developed and applied . This method enabled fire prevention, and environmental

Spatial organization of RNA polymerase II inside a mammalian cell nucleus revealed by reflected light-sheet superresolution microscopy

PubMed Central

Zhao, Ziqing W.; Roy, Rahul; Gebhardt, J. Christof M.; Suter, David M.; Chapman, Alec R.; Xie, X. Sunney

2014-01-01

Superresolution microscopy based on single-molecule centroid determination has been widely applied to cellular imaging in recent years. However, quantitative imaging of the mammalian nucleus has been challenging due to the lack of 3D optical sectioning methods for normal-sized cells, as well as the inability to accurately count the absolute copy numbers of biomolecules in highly dense structures. Here we report a reflected light-sheet superresolution microscopy method capable of imaging inside the mammalian nucleus with superior signal-to-background ratio as well as molecular counting with single-copy accuracy. Using reflected light-sheet superresolution microscopy, we probed the spatial organization of transcription by RNA polymerase II (RNAP II) molecules and quantified their global extent of clustering inside the mammalian nucleus. Spatiotemporal clustering analysis that leverages on the blinking photophysics of specific organic dyes showed that the majority (>70%) of the transcription foci originate from single RNAP II molecules, and no significant clustering between RNAP II molecules was detected within the length scale of the reported diameter of “transcription factories.” Colocalization measurements of RNAP II molecules equally labeled by two spectrally distinct dyes confirmed the primarily unclustered distribution, arguing against a prevalent existence of transcription factories in the mammalian nucleus as previously proposed. The methods developed in our study pave the way for quantitative mapping and stoichiometric characterization of key biomolecular species deep inside mammalian cells. PMID:24379392

Identification and characterization by LC-UV-MS/MS of melanotan II skin-tanning products sold illegally on the Internet.

PubMed

Breindahl, Torben; Evans-Brown, Michael; Hindersson, Peter; McVeigh, Jim; Bellis, Mark; Stensballe, Allan; Kimergård, Andreas

2015-02-01

New methods were developed and validated to determine the identity, contents, and purity of samples of melanotan II, a synthetic melanocortin receptor agonist, sold in vials as injectable skin-tanning products that were purchased from three online shops. Methods were based on liquid chromatography with ultra-violet detection (LC-UV) at wavelength 218 nm, and tandem mass spectrometric detection (MS/MS) after collision-induced fragmentation of the double charged [M+2H](2+) precursor ion (m/z 513). Identification of melanotan II was verified by correct chromatographic retention time, and relative abundance ratios of five qualifying fragment ions. LC-UV was used to quantify melanotan II as well as impurities. Method validation was performed with reference to guidelines for assessing active substances in authorized medicinal products to reach acceptable accuracy and precision. Vials from two shops contained unknown impurities ranging from 4.1 to 5.9%; impurities from one shop were below the quantification limit. The total amount of melanotan II in vials ranged between 4.32 and 8.84 mg, although each shop claimed that vials contained 10 mg melanotan II. A broad range of drugs used for enhancement purposes can be obtained from the illicit market. However, users of these drugs may be exposed to a range of potential harms, as shown in this study, given that these products are manufactured, distributed and supplied from an illicit market. Copyright © 2014 John Wiley & Sons, Ltd.

Educational Methods for Deaf-Blind and Severely Handicapped Students. Volume II.

ERIC Educational Resources Information Center

Texas Education Agency, Austin. Div. of Special Education.

The book presents 17 papers originally presented at a 1978 Texas conference on educational methods for deaf-blind and severely handicapped students, covering the areas of motor development, auditory assessment and hearing loss, communication, cognition, prevocational training, and functional living skills. Titles and authors include "An Overview…

24 CFR Appendix II to Subpart C of... - Development of Standards; Calculation Methods

Code of Federal Regulations, 2012 CFR

2012-04-01

...; Calculation Methods I. Background Information Concerning the Standards (a) Thermal Radiation: (1) Introduction... and structures in the event of fire. The resulting fireball emits thermal radiation which is absorbed... radiation being emitted. The radiation can cause severe burn, injuries and even death to exposed persons...

Spiritual Development and Death Attitude in Female Patients With Type II Diabetes

PubMed Central

Nozari, Masoumeh; Khalilian, Alireza; Dousti, Yarali

2014-01-01

Objective: The present study aimed to investigate the differences regarding spiritual development dimensions and death attitude profiles, and also to determinate association between them, in patients suffering from type II diabetes. Methods: In a cross-sectional design study, 100 female outpatients who were suffering from type II diabetes were recruited in Imam Khomeini Hospital, Sari, Iran. Data were collected through two questionnaires including the Spiritual Assessment Inventory (SAI) and the Death Attitude Profile-Revised (DAPR). Analysis of the data involved analysis of covariance (ANCOVA) with the Fisher's Least Significant Difference (LSD) as post-hoc test plus the Pearson correlation. Results: There was a statistical significant difference in spiritual development dimensions and death attitude profile. The results showed that spiritual development were significantly associated with some items of death attitude profiles. Conclusion: Awareness of God was suitable in diabetic patients, but the quality of relationship with God indicated spiritually immature. It is necessary to provide instruction to improve patient's death attitude and following health behavior. PMID:25780376

Developing Equipotent Teixobactin Analogues against Drug-Resistant Bacteria and Discovering a Hydrophobic Interaction between Lipid II and Teixobactin.

PubMed

Zong, Yu; Sun, Xiuyun; Gao, Hongying; Meyer, Kirsten J; Lewis, Kim; Rao, Yu

2018-04-26

Teixobactin, targeting lipid II, represents a new class of antibiotics with novel structures and has excellent activity against Gram-positive pathogens. We developed a new convergent method to synthesize a series of teixobactin analogues and explored structure-activity relationships. We obtained equipotent and simplified teixobactin analogues, replacing the l- allo-enduracididine with lysine, substituting oxygen to nitrogen on threonine, and adding a phenyl group on the d-phenylalanine. On the basis of the antibacterial activities that resulted from corresponding modifications of the d-phenylalanine, we propose a hydrophobic interaction between lipid II and the N-terminal of teixobactin analogues, which we map out with our analogue 35. Finally, a representative analogue from our series showed high efficiency in a mouse model of Streptococcus pneumoniae septicemia.

Development of X-ray computed tomography inspection facility for the H-II solid rocket boosters

NASA Astrophysics Data System (ADS)

Sasaki, M.; Fujita, T.; Fukushima, Y.; Shimizu, M.; Itoh, S.; Satoh, A.; Miyamoto, H.

The National Space Development Agency of Japan (NASDA) initiated the development of an X-ray computed tomography (CT) equipment for the H-II solid rocket boosters (SRBs) in 1987 for the purpose of minimizing inspection time and achieving high cost-effectiveness. The CT facility has been completed in Jan. 1991 in Tanegashima Space Center for the inspection of the SRBs transported from the manufacturer's factory to the launch site. It was first applied to the qualification model SRB from Feb. to Apr. in 1991. Through the CT inspection of the SRB, it has been confirmed that inspection time decreased significantly compared with the X-ray radiography method and that even an unskilled inspector could find various defects. As a result, the establishment of a new reliable inspection method for the SRB has been verified. In this paper, the following are discussed: (1) the defect detectability of the CT equipment using a dummy SRB with various artificial defects, (2) the performance comparison between the CT method and the X-ray radiography method, (3) the reliability of the CT equipment, and (4) the radiation shield design of the nondestructive test building.

EEG, HRV and Psychological Correlates while Playing Bejeweled II: A Randomized Controlled Study.

PubMed

Russoniello, Carmen V; O'Brien, Kevin; Parks, Jennifer M

2009-01-01

Stress related medical disorders such as cardiovascular disease, diabetes, depression, and anxiety are serious medical issues that can cause disability and death. Interventions to prevent their development and exacerbation are needed. Casual video games (CVGs) are fun, easy to play, spontaneous and tremendously popular. People report that they play these games because they decrease their stress and improve their mood. This study tested this theory by comparing people playing Bejeweled II a popular CVG with control subjects measured under similar conditions. Electroencephalographic (EEG) changes after playing Bejeweled II were consistent with increased mood and corroborated with similar findings on psychological reports. Moreover, heart rate variability (HRV) changes consistent with autonomic nervous system relaxation or decreased physical stress were also recorded. It is concluded, therefore, that playing a CVG like Bejeweled II can increase mood and decrease stress. These finding have broad implications and include the potential development of prescriptive interventions using Bejeweled II to prevent and treat stress related medical disorders. Finally, these findings demonstrate a method using EEG, HRV and psychological correlates to understand the psychophysiological or cybernetic interconnection between participant and video game.

Stochastic and Deterministic Crystal Structure Solution Methods in GSAS-II: Monte Carlo/Simulated Annealing Versus Charge Flipping

DOE PAGES

Von Dreele, Robert

2017-08-29

One of the goals in developing GSAS-II was to expand from the capabilities of the original General Structure Analysis System (GSAS) which largely encompassed just structure refinement and post refinement analysis. GSAS-II has been written almost entirely in Python loaded with graphics, GUI and mathematical packages (matplotlib, pyOpenGL, wxpython, numpy and scipy). Thus, GSAS-II has a fully developed modern GUI as well as extensive graphical display of data and results. However, the structure and operation of Python has required new approaches to many of the algorithms used in crystal structure analysis. The extensions beyond GSAS include image calibration/integration as wellmore » as peak fitting and unit cell indexing for powder data which are precursors for structure solution. Structure solution within GSAS-II begins with either Pawley or LeBail extracted structure factors from powder data or those measured in a single crystal experiment. Both charge flipping and Monte Carlo-Simulated Annealing techniques are available; the former can be applied to (3+1) incommensurate structures as well as conventional 3D structures.« less

Screening of Chemical Dyes in Traditional Chinese Medicine by HPTLC-MS.

PubMed

He, Fengyan; He, Yi; Zheng, Xiaowei; Wang, Ruizhong; Lu, Jing; Dai, Zhong; Ma, Shuangcheng

2018-05-01

It has been uncovered that chemical dyes are illegally used in traditional Chinese medicines to brighten color and cover up inferiority, which threaten the safety of patients. In the present study, an HPTLC-MS method was developed for the effective screening of 11 chemical dyes (Sudan I, II, III, and IV; 808 Scarlet; Sudan Red 7B; malachite green; Basic Orange 2; auramine; Orange II; and erythrosine) in traditional Chinese medicine (TCM) raw materials and Chinese patent medicines. Firstly, unwashed HPTLC plates were chosen by comparing the background signals of the TLC plates used directly and prewashed with analytical grade and HPLC grade solvents. Twice developments were conducted to isolate chemical dyes of different polarity. Possible adulterants were preliminarily identified by comparing Rf values and in situ UV-Vis spectra with those of the references. Further confirmation was conducted by tandem MS analysis via an elution head-based TLC-MS interface. Sudan I and IV, 808 Scarlet, and Orange II were successfully detected in eight batches of TCM. The proposed method could be applied as a reliable technology for the screening of chemical dyes in TCM.

Zincon-modified activated carbon for solid-phase extraction and preconcentration of trace lead and chromium from environmental samples.

PubMed

Li, Zhenhua; Chang, Xijun; Hu, Zheng; Huang, Xinping; Zou, Xiaojun; Wu, Qiong; Nie, Rong

2009-07-15

A new method that utilizes zincon-modified activated carbon (AC-ZCN) as a solid-phase extractant has been developed for simultaneous preconcentration of trace Cr(III) and Pb(II) prior to the measurement by inductively coupled plasma optical emission spectrometry (ICP-OES). The separation/preconcentration conditions of analytes were investigated, including effects of pH, the shaking time, the sample flow rate and volume, the elution condition and the interfering ions. At pH 4, the maximum adsorption capacity of Cr(III) and Pb(II) onto the AC-ZCN were 17.9 and 26.7 mg g(-1), respectively. The adsorbed metal ions were quantitatively eluted by 1 mL of 0.1 mol L(-1) HCl. Common coexisting ions did not interfere with the separation. According to the definition of IUPAC, the detection limits (3 sigma) of this method for Cr(III) and Pb(II) were 0.91 and 0.65 ng mL(-1), respectively. The relative standard deviation under optimum condition is less than 3.5% (n=8). The method has been applied for the determination of Cr(III) and Pb(II) in biological materials and water samples with satisfactory results.

Flow injection chemiluminescent determination of tetracycline using a tris(2,2'-bipyridine)ruthenium(II)-cerium(IV) sulphate system.

PubMed

Guo, Liangqia; Xie, Zenghong; Lin, Xucong; Liu, Xiaohua; Zhang, Weilin; Chen, Guonan

2004-01-01

A flow-injection chemiluminescence method for the determination of tetracycline was developed. The method is based on an enhancement by tetracycline of the chemiluminescence light emission of tris(2,2'-bipyridine)ruthenium(II). In sulphuric acid medium, the chemiluminescence is generated by the continuous oxidation of tris(2,2'-bipyridine)ruthenium(II) by cerium (IV) sulphate. The light-emission intensity is greatly enhanced in the presence of tetracycline. Under the optimum conditions, the calibration curve is linear over the range 3.75 x 10(-8) g/mL-1.5 x 10(-5) g/mL for tetracycline with the linear equation: deltaINT = 205.898 x C - 20.442 (R2 = 0.9974). The detection limit is 3.27 x 10(-8) g/mL. The proposed method was also successfully used to determine tetracycline in pharmaceutical formulation (mean recovery of tetracycline, 100.7%). Copyright 2004 John Wiley & Sons, Ltd.

Two spectrophotometric methods for simultaneous determination of some antihyperlipidemic drugs

PubMed Central

Abdelwahab, Nada S.; El-Zeiny, Badr A.; Tohamy, Salwa I.

2012-01-01

Two simple, accurate, precise and economic spectrophotometric methods have been developed for simultaneous determination of Atorvastatin calcium (ATR) and Ezetimibe (EZ) in their bulk powder and pharmaceutical dosage form. Method (I) is based on dual wavelength analysis while method (II) is the mean centering of ratio spectra spectrophotometric (MCR) method. In method (I), two wavelengths were selected for each drug in such a way that the difference in absorbance was zero for the second drug. At wavelengths 226.6 and 244 nm EZ had equal absorbance values; therefore, these two wavelengths have been used to determine ATR; on a similar basis 228.6 and 262.8 nm were selected to determine EZ in their binary mixtures. In method II, the absorption spectra of both ATR and EZ with different concentrations were recorded over the range 200–350, divided by the spectrum of suitable divisor of both ATR and EZ and then the obtained ratio spectra were mean centered. The concentrations of active components were then determined from the calibration graphs obtained by measuring the amplitudes at 215–260 nm (peak to peak) for both ATR and EZ. Accuracy and precision of the developed methods have been tested; in addition recovery studies have been carried out in order to confirm their accuracy. On the other hand, selectivities of the methods were tested by application for determination of different synthetic mixtures containing different ratios of the studied drugs. The developed methods have been successfully used for determination of ATR and EZ in their combined dosage form and statistical comparison of the developed methods with the reported spectrophotometric one using F and Student's t-tests showed no significant difference regarding both accuracy and precision. PMID:29403754

Two spectrophotometric methods for simultaneous determination of some antihyperlipidemic drugs.

PubMed

Abdelwahab, Nada S; El-Zeiny, Badr A; Tohamy, Salwa I

2012-08-01

Two simple, accurate, precise and economic spectrophotometric methods have been developed for simultaneous determination of Atorvastatin calcium (ATR) and Ezetimibe (EZ) in their bulk powder and pharmaceutical dosage form. Method (I) is based on dual wavelength analysis while method (II) is the mean centering of ratio spectra spectrophotometric (MCR) method. In method (I), two wavelengths were selected for each drug in such a way that the difference in absorbance was zero for the second drug. At wavelengths 226.6 and 244 nm EZ had equal absorbance values; therefore, these two wavelengths have been used to determine ATR; on a similar basis 228.6 and 262.8 nm were selected to determine EZ in their binary mixtures. In method II, the absorption spectra of both ATR and EZ with different concentrations were recorded over the range 200-350, divided by the spectrum of suitable divisor of both ATR and EZ and then the obtained ratio spectra were mean centered. The concentrations of active components were then determined from the calibration graphs obtained by measuring the amplitudes at 215-260 nm (peak to peak) for both ATR and EZ. Accuracy and precision of the developed methods have been tested; in addition recovery studies have been carried out in order to confirm their accuracy. On the other hand, selectivities of the methods were tested by application for determination of different synthetic mixtures containing different ratios of the studied drugs. The developed methods have been successfully used for determination of ATR and EZ in their combined dosage form and statistical comparison of the developed methods with the reported spectrophotometric one using F and Student's t -tests showed no significant difference regarding both accuracy and precision.

Strategies for the screening of antibiotic residues in eggs: comparison of the validation of the classical microbiological method with an immunobiosensor method.

PubMed

Gaudin, Valérie; Rault, Annie; Hedou, Celine; Soumet, Christophe; Verdon, Eric

2017-09-01

Efficient screening methods are needed to control antibiotic residues in eggs. A microbiological kit (Explorer® 2.0 test (Zeu Inmunotech, Spain)) and an immunobiosensor kit (Microarray II (AM® II) on Evidence Investigator™ system (Randox, UK)) have been evaluated and validated for screening of antibiotic residues in eggs, according to the European decision EC/2002/657 and to the European guideline for the validation of screening methods. The e-reader™ system, a new automatic incubator/reading system, was coupled to the Explorer 2.0 test. The AM II kit can detect residues of six different families of antibiotics in different matrices including eggs. For both tests, a different liquid/liquid extraction of eggs had to be developed. Specificities of the Explorer 2.0 and AM II kit were equal to 8% and 0% respectively. The detection capabilities were determined for 19 antibiotics, with representatives from different families, for Explorer 2.0 and 12 antibiotics for the AM II kit. For the nine antibiotics having a maximum residue limit (MRL) in eggs, the detection capabilities CCβ of Explorer 2.0 were below the MRL for four antibiotics, equal to the MRL for two antibiotics and between 1 and 1.5 MRLs for the three remaining antibiotics (tetracyclines). For the antibiotics from other families, the detection capabilities were low for beta-lactams and sulfonamides and satisfactory for dihydrostreptomycin (DHS) and fluoroquinolones, which are usually difficult to detect with microbiological tests. The CCβ values of the AM II kit were much lower than the respective MRLs for three detected antibiotics (tetracycline, oxytetracycline, tylosin). Concerning the nine other antibiotics, the detection capabilities determined were low. The highest CCβ was obtained for streptomycin (100 µg kg -1 ).

Supercritical CO₂assisted extraction and LC-MS identification of picroside I and picroside II from Picrorhiza kurroa.

PubMed

Patil, Ajit A; Sachin, Bhusari S; Shinde, Devanand B; Wakte, Pravin S

2013-02-01

Picroside I and picroside II have been studied intensively because of their pharmacological actions and clinical applications. Numerous methods have been reported for extracting picroside I and picroside II from Picrorrhiza. kurroa rhizomes. This is the first report of picroside I and picroside II extraction using the supercritical carbon dioxide assisted extraction technique. To develop supercritical carbon dioxide assisted extraction and LC-MS identification of picroside I and picroside II from the Picrorrhiza kurroa Royle rhizomes. Surface response methodology based on 3³ fractional factorial design was used to extract picroside I and picroside II from P. kurroa rhizomes. The effects of various process factors, namely temperature (40-80°C), pressure (25-35 MPa) and co-solvent (methanol) concentration (0-10% v/v) on extraction yield of the two compounds were evaluated. The picroside I and picroside II contents were determined using validated LC-MS methodology. The maximum yield of picroside I (32.502 ± 1.131 mg/g) and picroside II (9.717 ± 0.382 mg/g) was obtained at the 10% v/v co-solvent concentration, 40°C temperature and 30 MPa pressure. The conventional Soxhlet assisted methanol extract of P. kurroa powder resulted in 36.743 ± 1.75 and 11.251 ± 0.54 mg/g yield of picroside I and picroside II, respectively. Variation of concentration and extraction time showed a significant effect on the picroside I and picroside II yield. Supercritical carbon dioxide assisted extraction using methanol as a co-solvent is an efficient and environmentally sustainable method for extracting picroside I and picroside II from P. kurroa rhizomes. Copyright © 2012 John Wiley & Sons, Ltd.

Use of poisons in determination of microbial manganese binding rates in seawater

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosson, R.A.; Tebo, B.M.; Nealson, K.H.

1984-04-01

A method was developed to determine whether microorganisms mediate the precipitation of manganese(II) in the marine environment. Radioactive /sup 54/Mn(II) was used as a tracer to measure the precipitation (binding and oxidation) of Mn(II) (i.e., the /sup 54/Mn(II) trapped on 0.2-..mu..m membrane filters) in the presence and absence of biological poisons. A variety of antibiotics, fixatives, and metabolic inhibitors were tested in laboratory control experiments to select poisons that did not interfere in the chemistry of manganese. The poisons were deemed suitable if (i) they did not complex Mn(II) more strongly than the ion-exchange resin Chelex 100, (ii) they didmore » not interfere in the adsorption of /sup 54/Mn(II) onto synthetic deltaMnO/sub 2/ (manganate), (iii) they did not cause desorption of /sup 54/Mn(II) which had been preadsorbed onto synthetic manganate, and (iv) they did not solubilize synthetic /sup 54/manganate. In addition, several known chelators, reducing agents, and buffers normally added to microbiological growth media or used in biochemical assays were tested. Most additions interfered to some extent with manganese chemistry. However, at least one inhibitor, sodium azide, or a mixture of sodium azide, penicillin, and tetracycline was shown to be appropriate for use in field studies of /sup 54/Mn(II) binding. Formaldehyde could also be used in short incubations (1 to 3 h) but was not suitable for longer time course studies. The method was applied to studies of Mn(II) precipitation in Saanich Inlet, British Columbia, Canada. Bacteria were shown to significantly enhance the rate of Mn(II) removal from solution in the manganese-rich particulate layer which occurs just above the oxygen-hydrogen sulfide interface in the water column. 23 references.« less

Near-infrared II fluorescence for imaging hindlimb vessel regeneration with dynamic tissue perfusion measurement.

PubMed

Hong, Guosong; Lee, Jerry C; Jha, Arshi; Diao, Shuo; Nakayama, Karina H; Hou, Luqia; Doyle, Timothy C; Robinson, Joshua T; Antaris, Alexander L; Dai, Hongjie; Cooke, John P; Huang, Ngan F

2014-05-01

Real-time vascular imaging that provides both anatomic and hemodynamic information could greatly facilitate the diagnosis of vascular diseases and provide accurate assessment of therapeutic effects. Here, we have developed a novel fluorescence-based all-optical method, named near-infrared II (NIR-II) fluorescence imaging, to image murine hindlimb vasculature and blood flow in an experimental model of peripheral arterial disease, by exploiting fluorescence in the NIR-II region (1000-1400 nm) of photon wavelengths. Because of the reduced photon scattering of NIR-II fluorescence compared with traditional NIR fluorescence imaging and thus much deeper penetration depth into the body, we demonstrated that the mouse hindlimb vasculature could be imaged with higher spatial resolution than in vivo microscopic computed tomography. Furthermore, imaging during 26 days revealed a significant increase in hindlimb microvascular density in response to experimentally induced ischemia within the first 8 days of the surgery (P<0.005), which was confirmed by histological analysis of microvascular density. Moreover, the tissue perfusion in the ischemic hindlimb could be quantitatively measured by the dynamic NIR-II method, revealing the temporal kinetics of blood flow recovery that resembled microbead-based blood flowmetry and laser Doppler blood spectroscopy. The penetration depth of millimeters, high spatial resolution, and fast acquisition rate of NIR-II imaging make it a useful imaging tool for murine models of vascular disease. © 2014 American Heart Association, Inc.

Functionality of In vitro Reconstituted Group II Intron RmInt1-Derived Ribonucleoprotein Particles.

PubMed

Molina-Sánchez, Maria D; García-Rodríguez, Fernando M; Toro, Nicolás

2016-01-01

The functional unit of mobile group II introns is a ribonucleoprotein particle (RNP) consisting of the intron-encoded protein (IEP) and the excised intron RNA. The IEP has reverse transcriptase activity but also promotes RNA splicing, and the RNA-protein complex triggers site-specific DNA insertion by reverse splicing, in a process called retrohoming. In vitro reconstituted ribonucleoprotein complexes from the Lactococcus lactis group II intron Ll.LtrB, which produce a double strand break, have recently been studied as a means of developing group II intron-based gene targeting methods for higher organisms. The Sinorhizobium meliloti group II intron RmInt1 is an efficient mobile retroelement, the dispersal of which appears to be linked to transient single-stranded DNA during replication. The RmInt1IEP lacks the endonuclease domain (En) and cannot cut the bottom strand to generate the 3' end to initiate reverse transcription. We used an Escherichia coli expression system to produce soluble and active RmInt1 IEP and reconstituted RNPs with purified components in vitro . The RNPs generated were functional and reverse-spliced into a single-stranded DNA target. This work constitutes the starting point for the use of group II introns lacking DNA endonuclease domain-derived RNPs for highly specific gene targeting methods.

Functionality of In vitro Reconstituted Group II Intron RmInt1-Derived Ribonucleoprotein Particles

PubMed Central

Molina-Sánchez, Maria D.; García-Rodríguez, Fernando M.; Toro, Nicolás

2016-01-01

The functional unit of mobile group II introns is a ribonucleoprotein particle (RNP) consisting of the intron-encoded protein (IEP) and the excised intron RNA. The IEP has reverse transcriptase activity but also promotes RNA splicing, and the RNA-protein complex triggers site-specific DNA insertion by reverse splicing, in a process called retrohoming. In vitro reconstituted ribonucleoprotein complexes from the Lactococcus lactis group II intron Ll.LtrB, which produce a double strand break, have recently been studied as a means of developing group II intron-based gene targeting methods for higher organisms. The Sinorhizobium meliloti group II intron RmInt1 is an efficient mobile retroelement, the dispersal of which appears to be linked to transient single-stranded DNA during replication. The RmInt1IEP lacks the endonuclease domain (En) and cannot cut the bottom strand to generate the 3′ end to initiate reverse transcription. We used an Escherichia coli expression system to produce soluble and active RmInt1 IEP and reconstituted RNPs with purified components in vitro. The RNPs generated were functional and reverse-spliced into a single-stranded DNA target. This work constitutes the starting point for the use of group II introns lacking DNA endonuclease domain-derived RNPs for highly specific gene targeting methods. PMID:27730127

How copper corrosion can be retarded--New ways investigating a chronic problem for cellulose in paper.

PubMed

Ahn, Kyujin; Hofmann, Christa; Horsky, Monika; Potthast, Antje

2015-12-10

To better assess the stabilization effects of chemical treatments on Cu(II)-catalyzed cellulose degradation, we developed Cu(II)-containing model rag paper with typical copper corrosion characteristics using e-beam radiation. The paper can be prepared homogeneously and quickly compared to tedious pre-aging methods. Using the Cu(II)-containing model rag paper, the stabilization effects of various chemicals on Cu(II)-catalyzed degradation of cellulose were tested. Benzotriazol was highly effective in retarding the degradation of the Cu(II)-containing model rag paper under hot and humid aging condition, as well as under photo-oxidative stress. Tetrabutylammonium bromide reduced Cu(II)-catalyzed degradation of cellulose, but its efficacy was dependent on the accelerated aging conditions. The results with the alkaline treatments and gelatin treatment suggested that their roles in the degradation mechanisms of cellulose in the presence of Cu(II) differ from those of benzotriazol and tetrabutylammonium bromide. Copyright © 2015 Elsevier Ltd. All rights reserved.

Novel Galvanic Corrosion Inhibitors: Synthesis, Characterization, Fabrication and Testing

DTIC Science & Technology

2007-09-30

have attempted to develop methods based on chemical structural modification to prevent galvanically-induced composite corrosion. [9, 10-12] These...of the two metallopolymers 11 and 12 show characteristic MLCT (metal-to-ligand charge transfer) absorption band of tris(bipyridyl)Ru(II) unit at k...showed absorption band at 450 nm and emission band at 325 nm of tris(bipyridyl)Ru(II) units in its respective UV-vis and fluorescence spectra. Very

Sector Review: Workshops I and II. Pengian kebijakan, Subsektor Pendidikan, SD dan SMP. East Java Province, West Java Province, South Sulawes Province. Educational Policy and Planning Project.

ERIC Educational Resources Information Center

Florida State Univ., Tallahassee. Learning Systems Inst.

This publication contains the first two of three training workshop manuals designed to be used in conducting an update of the Indonesian Education and Human Resources Sector Assessment. Workshop I covers the basic concepts, skills, and methods needed to design subsector updates and develop a draft plan for update activities. Workshops II and III…

Magnetic-Field Dependences of Thermodynamic Quantities in the Vortex State of Type-Ii Superconductors

NASA Astrophysics Data System (ADS)

Watanabe, Koichi; Kita, Takafumi; Arai, Masao

2006-08-01

We develop an alternative method to solve the Eilenberger equations numerically for the vortex-lattice states of type-II superconductors. Using it, we clarify the magnetic-field and impurity-concentration dependences of the magnetization, the entropy, the Pauli paramagnetism, and the mixing of higher Landau levels in the pair potential for two-dimensional s- and dx2-y2-wave superconductors with a cylindrical Fermi surface.

Novelmetal-organic photocatalysts: Synthesis, characterization and decomposition of organic dyes

NASA Astrophysics Data System (ADS)

Gopal Reddy, N. B.; Murali Krishna, P.; Kottam, Nagaraju

2015-02-01

An efficient method for the photocatalytic degradation of methylene blue in an aqueous medium was developed using metal-organic complexes. Two novel complexes were synthesized using, Schiff base ligand, N‧-[(E)-(4-ethylphenyl)methylidene]-4-hydroxybenzohydrazide (HL) and Ni(II) (Complex 1)/Co(II) (Complex 2) chloride respectively. These complexes were characterized using microanalysis, various spectral techniques. Spectral studies reveal that the complexes exhibit square planar geometry with ligand coordination through azomethine nitrogen and enolic oxygen. The effects of catalyst dosage, irradiation time and aqueous pH on the photocatalytic activity were studied systematically. The photocatalytic activity was found to be more efficient in the presence of Ni(II) complexes than the Co(II) complex. Possible mechanistic aspects were discussed.

Polydisulfide Manganese(II) Complexes as Non-Gadolinium Biodegradable Macromolecular MRI Contrast Agents

PubMed Central

Ye, Zhen; Jeong, Eun-Kee; Wu, Xueming; Tan, Mingqian; Yin, Shouyu; Lu, Zheng-Rong

2011-01-01

Purpose To develop safe and effective manganese(II) based biodegradable macromolecular MRI contrast agents. Materials and Methods In this study, we synthesized and characterized two polydisulfide manganese(II) complexes, Mn-DTPA cystamine copolymers and Mn-EDTA cystamine copolymers, as new biodegradable macromolecular MRI contrast agents. The contrast enhancement of the two manganese based contrast agents were evaluated in mice bearing MDA-MB-231 human breast carcinoma xenografts, in comparison with MnCl2. Results The T1 and T2 relaxivities were 4.74 and 10.38 mM−1s−1 per manganese at 3T for Mn-DTPA cystamine copolymers (Mn=30.50 kDa) and 6.41 and 9.72 mM−1s−1 for Mn-EDTA cystamine copolymers (Mn= 61.80 kDa). Both polydisulfide Mn(II) complexes showed significant liver, myocardium and tumor enhancement. Conclusion The manganese based polydisulfide contrast agents have a potential to be developed as alternative non-gadolinium contrast agents for MR cancer and myocardium imaging. PMID:22031457

The development of local calibration factors - phase II : Maryland freeways and ramps : final report.

DOT National Transportation Integrated Search

2016-11-01

The goal of the study was to develop local calibration factors (LCFs) for Maryland freeways in order to apply the predictive methods of the Highway Safety Manual (HSM) to the state. LCFs were computed for freeway segments, speed-change lanes, and sig...

Objective Lightning Probability Forecasting for Kennedy Space Center and Cape Canaveral Air Force Station, Phase III

NASA Technical Reports Server (NTRS)

Crawford, Winifred C.

2010-01-01

The AMU created new logistic regression equations in an effort to increase the skill of the Objective Lightning Forecast Tool developed in Phase II (Lambert 2007). One equation was created for each of five sub-seasons based on the daily lightning climatology instead of by month as was done in Phase II. The assumption was that these equations would capture the physical attributes that contribute to thunderstorm formation more so than monthly equations. However, the SS values in Section 5.3.2 showed that the Phase III equations had worse skill than the Phase II equations and, therefore, will not be transitioned into operations. The current Objective Lightning Forecast Tool developed in Phase II will continue to be used operationally in MIDDS. Three warm seasons were added to the Phase II dataset to increase the POR from 17 to 20 years (1989-2008), and data for October were included since the daily climatology showed lightning occurrence extending into that month. None of the three methods tested to determine the start of the subseason in each individual year were able to discern the start dates with consistent accuracy. Therefore, the start dates were determined by the daily climatology shown in Figure 10 and were the same in every year. The procedures used to create the predictors and develop the equations were identical to those in Phase II. The equations were made up of one to three predictors. TI and the flow regime probabilities were the top predictors followed by 1-day persistence, then VT and Ll. Each equation outperformed four other forecast methods by 7-57% using the verification dataset, but the new equations were outperformed by the Phase II equations in every sub-season. The reason for the degradation may be due to the fact that the same sub-season start dates were used in every year. It is likely there was overlap of sub-season days at the beginning and end of each defined sub-season in each individual year, which could very well affect equation performance.

Determination of Trace lead (II) by Resonance Light Scattering Based on Pb (II)-KI-MG System

NASA Astrophysics Data System (ADS)

Chen, Ninghua; Yang, Yingchun; Hao, Shuai; Li, Yangmin

2018-01-01

In pH=3.0 weak acidic solution, it is found that Pb2+ can react with I-to form [PbI4]2-, and it further reacted with MG to form ion-association complex. As a result, the new spectra of RLS appeared and their intensities enhanced greatly. Accordingly, a new method developed for the determination of Pb (II).The appropriate reaction conditions were optimized through experiments. The results show that a strong and stable resonance scattering spectra emerge at the wavelength of 338 nm. The resonance light scattering strength (ΔIRLS) has good linear relationship with the concentration of Pb (II) in the range of 0.2 μg/mL ~ 1.0 μg/mL. The detection limits (LOD) is 0.0155 μg/mL. The relative standard deviation (RSD) is 3.61% (n=11) for the determination of 0.6 μg/mL Pb (II) standard solution. And this method was successfully applied to the determination of three environmental water samples (nongfu spring, tap water, laboratory wastewater). Results illustrate that the addition standard recovery are 80%~107% with relative standard deviation (RSD) between 1.8% to 4.6%.

Age, size, and position of H ii regions in the Galaxy. Expansion of ionized gas in turbulent molecular clouds

NASA Astrophysics Data System (ADS)

Tremblin, P.; Anderson, L. D.; Didelon, P.; Raga, A. C.; Minier, V.; Ntormousi, E.; Pettitt, A.; Pinto, C.; Samal, M. R.; Schneider, N.; Zavagno, A.

2014-08-01

Aims: This work aims to improve the current understanding of the interaction between H ii regions and turbulent molecular clouds. We propose a new method to determine the age of a large sample of OB associations by investigating the development of their associated H ii regions in the surrounding turbulent medium. Methods: Using analytical solutions, one-dimensional (1D), and three-dimensional (3D) simulations, we constrained the expansion of the ionized bubble depending on the turbulence level of the parent molecular cloud. A grid of 1D simulations was then computed in order to build isochrone curves for H ii regions in a pressure-size diagram. This grid of models allowed us to date a large sample of OB associations that we obtained from the H ii Region Discovery Survey (HRDS). Results: Analytical solutions and numerical simulations showed that the expansion of H ii regions is slowed down by the turbulence up to the point where the pressure of the ionized gas is in a quasi-equilibrium with the turbulent ram pressure. Based on this result, we built a grid of 1D models of the expansion of H ii regions in a profile based on Larson's laws. We take the 3D turbulence into account with an effective 1D temperature profile. The ages estimated by the isochrones of this grid agree well with literature values of well known regions such as Rosette, RCW 36, RCW 79, and M 16. We thus propose that this method can be used to find ages of young OB associations through the Galaxy and also in nearby extra-galactic sources.

A Type II Supernova Hubble Diagram from the CSP-I, SDSS-II, and SNLS Surveys

NASA Astrophysics Data System (ADS)

de Jaeger, T.; González-Gaitán, S.; Hamuy, M.; Galbany, L.; Anderson, J. P.; Phillips, M. M.; Stritzinger, M. D.; Carlberg, R. G.; Sullivan, M.; Gutiérrez, C. P.; Hook, I. M.; Howell, D. Andrew; Hsiao, E. Y.; Kuncarayakti, H.; Ruhlmann-Kleider, V.; Folatelli, G.; Pritchet, C.; Basa, S.

2017-02-01

The coming era of large photometric wide-field surveys will increase the detection rate of supernovae by orders of magnitude. Such numbers will restrict spectroscopic follow-up in the vast majority of cases, and hence new methods based solely on photometric data must be developed. Here, we construct a complete Hubble diagram of Type II supernovae (SNe II) combining data from three different samples: the Carnegie Supernova Project-I, the Sloan Digital Sky Survey II SN, and the Supernova Legacy Survey. Applying the Photometric Color Method (PCM) to 73 SNe II with a redshift range of 0.01-0.5 and with no spectral information, we derive an intrinsic dispersion of 0.35 mag. A comparison with the Standard Candle Method (SCM) using 61 SNe II is also performed and an intrinsic dispersion in the Hubble diagram of 0.27 mag, I.e., 13% in distance uncertainties, is derived. Due to the lack of good statistics at higher redshifts for both methods, only weak constraints on the cosmological parameters are obtained. However, assuming a flat universe and using the PCM, we derive the universe’s matter density: {{{Ω }}}m={0.32}-0.21+0.30 providing a new independent evidence for dark energy at the level of two sigma. This paper includes data gathered with the 6.5 m Magellan Telescopes, with the du Pont and Swope telescopes located at Las Campanas Observatory, Chile; and the Gemini Observatory, Cerro Pachon, Chile (Gemini Program N-2005A-Q-11, GN-2005B-Q-7, GN-2006A-Q-7, GS-2005A-Q-11, GS-2005B-Q-6, and GS-2008B-Q-56). Based on observations collected at the European Organization for Astronomical Research in the Southern Hemisphere, Chile (ESO Programmes 076.A-0156,078.D-0048, 080.A-0516, and 082.A-0526).

Development and evaluation of a suppository formulation containing Lactobacillus and its application in vaginal diseases.

PubMed

Kale, Vinita V; Trivedi, Rashmi V; Wate, Sanjay P; Bhusari, Kishor P

2005-11-01

Lactobacillus has long been considered the protective flora in the vagina that displaces and kills vaginal pathogens. Lactic acid, H2O2, and antibacterial agents such as lactocin and bacitracin produced by Lactobacillus act against the vaginal pathogens. The first objective of this research was to develop a local application pharmaceutical formulation of a vaginal suppository containing lyophilized culture of Lactobacillus. The second objective was to establish its in vivo performance by developing in vitro methods of evaluation. Lyophilized culture of Lactobacillus sporogenes was selected for this study. Three formulations of the suppositories were prepared by the molding method. Formulations I, II, and III contained cocoa butter, glycerinated gelatin, and PEG 1000 base, respectively. The prepared suppositories were characterized for physical properties. Assembly to simulate the application site was designed. Methods to evaluate the viability, production of lactic acid, and H2O2 produced by the released Lactobacillus at the application site were developed and the antagonistic activity was demonstrated. From the physical characteristics of the suppository formulations, the glycerinated gelatin suppository (formulation II) containing lyophilized Lactobacillus was found to be satisfactory. The developed assembly was satisfactory in simulating the application site. The Lactobacillus released was viable and exhibited the production of lactic acid, hydrogen peroxide, and antagonistic activity against the uropathogen. The suppository formulation containing Lactobacillus and the methods of its evaluation were successfully developed in this research work and have several applications in the vaginal diseases of women.

The Autoregressive Method: A Method of Approximating and Estimating Positive Functions

DTIC Science & Technology

1976-08-01

in drawing the curves, thanks to computer graphics. A few people ha’ very imaginatively pro- posed - td developed new ways of visualizing the data...k= -= it turns out that , , 0ki < 0 is a sufficient condition for all our k= -cc ( operations to be valid. Ii_ _ _ _ _ _ __ __ _ _ _ _ -106- We will

The Development of an Occupational Information System (OIS), Volume II.

ERIC Educational Resources Information Center

Louisiana State Univ., Baton Rouge. Div. of Continuing Education.

Suppliers of postsecondary trained manpower data in Louisiana were surveyed during a project to obtain labor market information and occupational supply/demand information. All supply data were computerized and assigned to the appropriate training file. The data compiled fell into four major categories with regard to the method(s) of capture and…

Spectrophotometric and spectrofluorimetric determination of indacaterol maleate in pure form and pharmaceutical preparations: application to content uniformity.

PubMed

El-Ashry, S M; El-Wasseef, D R; El-Sherbiny, D T; Salem, Y A

2015-09-01

Two simple, rapid, sensitive and precise spectrophotometric and spectrofluorimetric methods were developed for the determination of indacaterol maleate in bulk powder and capsules. Both methods were based on the direct measurement of the drug in methanol. In the spectrophotometric method (Method I) the absorbance was measured at 259 nm. The absorbance-concentration plot was rectilinear over the range 1.0-10.0 µg mL(-1) with a lower detection limit (LOD) of 0.078 µg mL(-1) and lower quantification limit (LOQ) of 0.238 µg mL(-1). Meanwhile in the spectrofluorimetric method (Method II) the native fluorescence was measured at 358 nm after excitation at 258 nm. The fluorescence-concentration plot was rectilinear over the range of 1.0-40.0 ng mL(-1) with an LOD of 0.075 ng mL(-1) and an LOQ of 0.226 ng mL(-1). The proposed methods were successfully applied to the determination of indacaterol maleate in capsules with average percent recoveries ± RSD% of 99.94 ± 0.96 for Method I and 99.97 ± 0.81 for Method II. In addition, the proposed methods were extended to a content uniformity test according to the United States Pharmacopoeia (USP) guidelines and were accurate, precise for the capsules studied with acceptance value 3.98 for Method I and 2.616 for Method II. Copyright © 2015 John Wiley & Sons, Ltd.

Simultaneous determination of calycosin-7-O-β-D-glucoside, ononin, calycosin, formononetin, astragaloside IV, and astragaloside II in rat plasma after oral administration of Radix Astragali extraction for their pharmacokinetic studies by ultra-pressure liquid chromatography with tandem mass spectrometry.

PubMed

Liu, Xiao-hua; Zhao, Jian-bang; Guo, Long; Yang, Ying-lai; Hu, Fang; Zhu, Rui-juan; Feng, Shi-lan

2014-09-01

A sensitive and reliable ultra-pressure liquid chromatography with tandem mass spectrometry (UPLC-MS) was developed and validated for simultaneous quantification of six main bioactive components, i.e., calycosin-7-O-β-D-glucoside, ononin, calycosin, formononetin, astragaloside IV, and astragaloside II in rat plasma after oral administration of the 95 % ethanol extraction from Radix Astragali. Plasma samples were extracted with Waters Oasis(TM) HLB 1 cc (30 mg) Extraction Cartridges (SPE) separated on an UPLC™ BEH C18 column and detected by MS with electro spray ionization interface in positive selective ion monitoring mode. Calibration curves offered linear ranges of two orders of magnitude with r (2) > 0.99. The method had the lower limit quantification of 1.30, 0.73, 1.17, 2.33, 0.63, and 0.83 ng/mL for ononin, calycosin, calycosin-7-O-β-D-glucoside, formononetin, astragaloside IV, and astragaloside II, respectively, with precision less than 10 %. The RSD of intra- and inter-day variations ranged from 1.66 to 6.46 and 3.39 to 6.58 %. This developed method was applied subsequently to pharmacokinetic studies of the six compounds in rats successfully. The proposed method was for the first time to compare the pharmacokinetic difference between calycosin-7-O-β-D-glucoside and calycosin in rat plasma, so as between ononin and formononetin, and studied to the astragaloside II pharmacokinetics in rat plasma.

A recursively formulated first-order semianalytic artificial satellite theory based on the generalized method of averaging. Volume 1: The generalized method of averaging applied to the artificial satellite problem

NASA Technical Reports Server (NTRS)

Mcclain, W. D.

1977-01-01

A recursively formulated, first-order, semianalytic artificial satellite theory, based on the generalized method of averaging is presented in two volumes. Volume I comprehensively discusses the theory of the generalized method of averaging applied to the artificial satellite problem. Volume II presents the explicit development in the nonsingular equinoctial elements of the first-order average equations of motion. The recursive algorithms used to evaluate the first-order averaged equations of motion are also presented in Volume II. This semianalytic theory is, in principle, valid for a term of arbitrary degree in the expansion of the third-body disturbing function (nonresonant cases only) and for a term of arbitrary degree and order in the expansion of the nonspherical gravitational potential function.

Prioritizing sewer rehabilitation projects using AHP-PROMETHEE II ranking method.

PubMed

Kessili, Abdelhak; Benmamar, Saadia

2016-01-01

The aim of this paper is to develop a methodology for the prioritization of sewer rehabilitation projects for Algiers (Algeria) sewer networks to support the National Sanitation Office in its challenge to make decisions on prioritization of sewer rehabilitation projects. The methodology applies multiple-criteria decision making. The study includes 47 projects (collectors) and 12 criteria to evaluate them. These criteria represent the different issues considered in the prioritization of the projects, which are structural, hydraulic, environmental, financial, social and technical. The analytic hierarchy process (AHP) is used to determine weights of the criteria and the Preference Ranking Organization Method for Enrichment Evaluations (PROMETHEE II) method is used to obtain the final ranking of the projects. The model was verified using the sewer data of Algiers. The results have shown that the method can be used for prioritizing sewer rehabilitation projects.

Simplified Acute Physiology Score II as Predictor of Mortality in Intensive Care Units: A Decision Curve Analysis

PubMed Central

Allyn, Jérôme; Ferdynus, Cyril; Bohrer, Michel; Dalban, Cécile; Valance, Dorothée; Allou, Nicolas

2016-01-01

Background End-of-life decision-making in Intensive care Units (ICUs) is difficult. The main problems encountered are the lack of a reliable prediction score for death and the fact that the opinion of patients is rarely taken into consideration. The Decision Curve Analysis (DCA) is a recent method developed to evaluate the prediction models and which takes into account the wishes of patients (or surrogates) to expose themselves to the risk of obtaining a false result. Our objective was to evaluate the clinical usefulness, with DCA, of the Simplified Acute Physiology Score II (SAPS II) to predict ICU mortality. Methods We conducted a retrospective cohort study from January 2011 to September 2015, in a medical-surgical 23-bed ICU at University Hospital. Performances of the SAPS II, a modified SAPS II (without AGE), and age to predict ICU mortality, were measured by a Receiver Operating Characteristic (ROC) analysis and DCA. Results Among the 4.370 patients admitted, 23.3% died in the ICU. Mean (standard deviation) age was 56.8 (16.7) years, and median (first-third quartile) SAPS II was 48 (34–65). Areas under ROC curves were 0.828 (0.813–0.843) for SAPS II, 0.814 (0.798–0.829) for modified SAPS II and of 0.627 (0.608–0.646) for age. DCA showed a net benefit whatever the probability threshold, especially under 0.5. Conclusion DCA shows the benefits of the SAPS II to predict ICU mortality, especially when the probability threshold is low. Complementary studies are needed to define the exact role that the SAPS II can play in end-of-life decision-making in ICUs. PMID:27741304

Making the invisible visible: improved electrospray ion formation of metalloporphyrins/-phthalocyanines by attachment of the formate anion (HCOO(-)).

PubMed

Hitzenberger, Jakob Felix; Dammann, Claudia; Lang, Nina; Lungerich, Dominik; García-Iglesias, Miguel; Bottari, Giovanni; Torres, Tomás; Jux, Norbert; Drewello, Thomas

2016-02-21

A protocol is developed for the coordination of the formate anion (HCOO(-)) to neutral metalloporphyrins (Pors) and -phthalocyanines (Pcs) containing divalent metals as a means to improve their ion formation in electrospray ionization (ESI). This method is particularly useful when the oxidation of the neutral metallomacrocycle fails. While focusing on Zn(II)Pors and Zn(II)Pcs, we show that formate is also readily attached to Mn(II), Mg(II) and Co(II)Pcs. However, for the Co(II)Pc secondary reactions can be observed. Upon collision-induced dissociation (CID), Zn(II)Por/Pc·formate supramolecular complexes can undergo the loss of CO2 in combination with transfer of a hydride anion (H(-)) to the zinc metal center. Further dissociation leads to electron transfer and hydrogen atom loss, generating a route to the radical anion of the Zn(II)Por/Pc without the need for electrochemical reduction, although the Zn(II)Por/Pc may have a too low electron affinity to allow electron transfer directly from the formate anion. In addition to single Por molecules, multi Por arrays were successfully analyzed by this method. In this case, multiple addition of formate occurs, giving rise to multiply charged species. In these multi Por arrays, complexation of the formate anion occurs by two surrounding Por units (sandwich). Therefore, the maximum attainment of formate anions in these arrays corresponds to the number of such sandwich complexes rather than the number of porphyrin moieties. The same bonding motif leads to dimers of the composition [(Zn(II)Por/Pc)2·HCOO](-). In these, the formate anion can act as a structural probe, allowing the distinction of isomeric ions with the formate bridging two macrocycles or being attached to a dimer of directly connected macrocycles.

Epigenetic Segregation of Microbial Genomes from Complex Samples Using Restriction Endonucleases HpaII and McrB.

PubMed

Liu, Guohong; Weston, Christopher Q; Pham, Long K; Waltz, Shannon; Barnes, Helen; King, Paula; Sphar, Dan; Yamamoto, Robert T; Forsyth, R Allyn

2016-01-01

We describe continuing work to develop restriction endonucleases as tools to enrich targeted genomes of interest from diverse populations. Two approaches were developed in parallel to segregate genomic DNA based on cytosine methylation. First, the methyl-sensitive endonuclease HpaII was used to bind non-CG methylated DNA. Second, a truncated fragment of McrB was used to bind CpG methylated DNA. Enrichment levels of microbial genomes can exceed 100-fold with HpaII allowing improved genomic detection and coverage of otherwise trace microbial genomes from sputum. Additionally, we observe interesting enrichment results that correlate with the methylation states not only of bacteria, but of fungi, viruses, a protist and plants. The methods presented here offer promise for testing biological samples for pathogens and global analysis of population methylomes.

A motif detection and classification method for peptide sequences using genetic programming.

PubMed

Tomita, Yasuyuki; Kato, Ryuji; Okochi, Mina; Honda, Hiroyuki

2008-08-01

An exploration of common rules (property motifs) in amino acid sequences has been required for the design of novel sequences and elucidation of the interactions between molecules controlled by the structural or physical environment. In the present study, we developed a new method to search property motifs that are common in peptide sequence data. Our method comprises the following two characteristics: (i) the automatic determination of the position and length of common property motifs by calculating the physicochemical similarity of amino acids, and (ii) the quick and effective exploration of motif candidates that discriminates the positives and negatives by the introduction of genetic programming (GP). Our method was evaluated by two types of model data sets. First, the intentionally buried property motifs were searched in the artificially derived peptide data containing intentionally buried property motifs. As a result, the expected property motifs were correctly extracted by our algorithm. Second, the peptide data that interact with MHC class II molecules were analyzed as one of the models of biologically active peptides with buried motifs in various lengths. Twofold MHC class II binding peptides were identified with the rule using our method, compared to the existing scoring matrix method. In conclusion, our GP based motif searching approach enabled to obtain knowledge of functional aspects of the peptides without any prior knowledge.

Analyzing Interactions by an IIS-Map-Based Method in Face-to-Face Collaborative Learning: An Empirical Study

ERIC Educational Resources Information Center

Zheng, Lanqin; Yang, Kaicheng; Huang, Ronghuai

2012-01-01

This study proposes a new method named the IIS-map-based method for analyzing interactions in face-to-face collaborative learning settings. This analysis method is conducted in three steps: firstly, drawing an initial IIS-map according to collaborative tasks; secondly, coding and segmenting information flows into information items of IIS; thirdly,…

Development of a Facility Management and Improvement Manual for Army Service Schools.

DTIC Science & Technology

1983-03-01

Ehhhhomhmhhhhlo EEEEEEEohhhhhI L-Ii Ilk . ~MICROCOPY RESOLUTION TEST CHART NATIONAL BURESU Of STA OSN-T63-A NA01BRA FSADRS16- construction m*nilhlli 8mbtg 10b...U.S. Army Construction Engineering Research Lab. P.O. Box 4005 • 4A762731AT41-A-001 Champaign, IL 61820 _ It. CONTROLLING OFFICtNAME AND ADDRESS 37...developing a data collection and analysis method. The prototype method was discussed in CERL Interim Report P-ill. 3 This prototype method was tested by

Determination of trace inorganic mercury species in water samples by cloud point extraction and UV-vis spectrophotometry.

PubMed

Ulusoy, Halil Ibrahim

2014-01-01

A new micelle-mediated extraction method was developed for preconcentration of ultratrace Hg(II) ions prior to spectrophotometric determination. 2-(2'-Thiazolylazo)-p-cresol (TAC) and Ponpe 7.5 were used as the chelating agent and nonionic surfactant, respectively. Hg(II) ions form a hydrophobic complex with TAC in a micelle medium. The main factors affecting cloud point extraction efficiency, such as pH of the medium, concentrations of TAC and Ponpe 7.5, and equilibration temperature and time, were investigated in detail. An overall preconcentration factor of 33.3 was obtained upon preconcentration of a 50 mL sample. The LOD obtained under the optimal conditions was 0.86 microg/L, and the RSD for five replicate measurements of 100 microg/L Hg(II) was 3.12%. The method was successfully applied to the determination of Hg in environmental water samples.

User's manual for the BNW-II optimization code for dry/wet-cooled power plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Braun, D.J.; Bamberger, J.A.; Braun, D.J.

1978-05-01

The User's Manual describes how to operate BNW-II, a computer code developed by the Pacific Northwest Laboratory (PNL) as a part of its activities under the Department of Energy (DOE) Dry Cooling Enhancement Program. The computer program offers a comprehensive method of evaluating the cost savings potential of dry/wet-cooled heat rejection systems. Going beyond simple ''figure-of-merit'' cooling tower optimization, this method includes such items as the cost of annual replacement capacity, and the optimum split between plant scale-up and replacement capacity, as well as the purchase and operating costs of all major heat rejection components. Hence the BNW-II code ismore » a useful tool for determining potential cost savings of new dry/wet surfaces, new piping, or other components as part of an optimized system for a dry/wet-cooled plant.« less

On the method of least squares. II. [for calculation of covariance matrices and optimization algorithms

NASA Technical Reports Server (NTRS)

Jefferys, W. H.

1981-01-01

A least squares method proposed previously for solving a general class of problems is expanded in two ways. First, covariance matrices related to the solution are calculated and their interpretation is given. Second, improved methods of solving the normal equations related to those of Marquardt (1963) and Fletcher and Powell (1963) are developed for this approach. These methods may converge in cases where Newton's method diverges or converges slowly.

Management System for Integrating Basic Skills 2 Training and Unit Training Programs

DTIC Science & Technology

1983-09-01

Social Sciences. NOTEs The findings in this report are not to be construed as en official Department of the Army position, unless so designated by other...This report describes methods used and results obtained in the design , development, and field test of a management system and curriculum components...for integrating the Army’s Basic Skills Education Program, Phase II (BSEP II) and unit training programs. The curriculum components are designed to

Simultaneous determination of rabeprazole sodium and itopride hydrochloride in capsule dosage form by spectrophotometry.

PubMed

Sabnis, Shweta S; Gandhi, Santosh V; Madgulkar, A R; Bothara, K G

Three methods viz. Absorbance Ratio Method (I), Dual Wavelength Method (II) and First Order Derivative Spectroscopic Method (III) for simultaneous estimation of Rabeprazole sodium and Itopride hydrochloride have been developed. The drugs obey Beer's law in the concentration range 2-20 microg/ml for RAB and 5-75 microg/ml for ITO. The results of analysis of drugs have been validated statistically and by recovery studies.

A more accurate detection of codon 72 polymorphism and LOH of the TP53 gene.

PubMed

Baccouche, Sami; Mabrouk, Imed; Said, Salem; Mosbah, Ali; Jlidi, Rachid; Gargouri, Ali

2003-01-10

The polymorphism at codon 72 of the TP53 gene has been extensively studied for its involvement in cancerogenesis and loss of heterozygosity (LOH) detection. Usually, the exon 4 of the TP53 gene is amplified by polymerase chain reaction (PCR) on DNA extracted from blood and tumor tissues, then digested by AccII. In the case of heterozygosity, the comparison of AccII profile from blood and tumor DNA PCR products allowed the identification of a potential LOH in the TP53 locus. This method can be hindered by a partial AccII digestion and/or DNA contamination of non-tumor cells. To circumvent these problems, we have developed a new approach by using the AccII restriction site between exon 4 and exon 6. The PCR amplification of exon 4-6, followed by AccII digestion allowed us to detect without ambiguity any LOH case.

Optical and electrical studies of cerium mixed oxides

NASA Astrophysics Data System (ADS)

Sherly, T. R.; Raveendran, R.

2014-10-01

The fast development in nanotechnology makes enthusiastic interest in developing nanomaterials having tailor made properties. Cerium mixed oxide materials have received great attention due to their UV absorption property, high reactivity, stability at high temperature, good electrical property etc and these materials find wide applications in solid oxide fuel cells, solar control films, cosmetics, display units, gas sensors etc. In this study cerium mixed oxide compounds were prepared by co-precipitation method. All the samples were doped with Zn (II) and Fe (II). Preliminary characterizations such as XRD, SEM / EDS, TEM were done. UV - Vis, Diffuse reflectance, PL, FT-IR, Raman and ac conductivity studies of the samples were performed.

Predicting site locations for biomass using facilities with Bayesian methods

Treesearch

Timothy M. Young; James H. Perdue; Xia Huang

2017-01-01

Logistic regression models combined with Bayesian inference were developed to predict locations and quantify factors that influence the siting of biomass-using facilities that use woody biomass in the Southeastern United States. Predictions were developed for two groups of mills, one representing larger capacity mills similar to pulp and paper mills (Group II...

Practical Tools for Content Development: Pre-Service Teachers' Experiences and Perceptions

ERIC Educational Resources Information Center

Yurtseven Avci, Zeynep; Eren, Esra; Seckin Kapucu, Munise

2016-01-01

This study adopts phenomenology approach as the research design method to investigate pre-service teachers' experiences and perceptions on using practical tools for content development. The participants are twenty-four pre-service teachers who were taking Computer II course during 2013-2014 spring semester at a public university in Turkey. During…

German Basic Course. Volume II, Lessons 16-25.

ERIC Educational Resources Information Center

Defense Language Inst., Washington, DC.

This is the first volume of the Intermediate Phase (lessons 16-92) of the German Basic Course developed by the Defense Language Institute. The course, normally requiring 19 weeks of training, focuses on developing mastery of structural elements of German through the audiolingual method. Dialogues are based on life situations and progress towards…

A method to develop vocabulary checklists in new languages and their validity to assess early language development.

PubMed

Prado, Elizabeth L; Phuka, John; Ocansey, Eugenia; Maleta, Kenneth; Ashorn, Per; Ashorn, Ulla; Adu-Afarwuah, Seth; Oaks, Brietta M; Lartey, Anna; Dewey, Kathryn G

2018-05-11

Since the adoption of United Nations' Sustainable Goal 4.2 to ensure that all children have access to quality early child development (ECD) so that they are ready for primary education, the demand for valid ECD assessments has increased in contexts where they do not yet exist. The development of early language ability is important for school readiness. Our objective was to evaluate the validity of a method to develop vocabulary checklists in new languages to assess early language development, based on the MacArthur-Bates Communicative Development Inventories. Through asking mothers of young children what words their children say and through pilot testing, we developed 100-word vocabulary checklists in multilingual contexts in Malawi and Ghana. In Malawi, we evaluated the validity of the vocabulary checklist among 29 children age 17-25 months compared to three language measures assessed concurrently: Developmental Milestones Checklist-II (DMC-II) language scale, Malawi Developmental Assessment Tool (MDAT) language scale, and the number of different words (NDW) in 30-min recordings of spontaneous speech. In Ghana, we assessed the predictive validity of the vocabulary checklist at age 18 months to forecast language, pre-academic, and other skills at age 4-6 years among 869 children. We also compared the predictive validity of the vocabulary checklist scores to that of other developmental assessments administered at age 18 months. In Malawi, the Spearman's correlation of the vocabulary checklist score with DMC-II language was 0.46 (p = 0.049), with MDAT language was 0.66 (p = 0.016) and with NDW was 0.50 (p = 0.033). In Ghana, the 18-month vocabulary checklist score showed the strongest (rho = 0.12-0.26) and most consistent (8/12) associations with preschool scores, compared to the other 18-month assessments. The largest coefficients were the correlations of the 18-month vocabulary score with the preschool cognitive factor score (rho = 0.26), language score (0.25), and pre-academic score (0.24). We have demonstrated the validity of a method to develop vocabulary checklists in new languages, which can be used in multilingual contexts, using a feasible adaptation process requiring about 2 weeks. This is a promising method to assess early language development, which is associated with later preschool language, cognitive, and pre-academic skills.

Expert opinions on the acceptance of alternative methods in food safety evaluations: Formulating recommendations to increase acceptance of non-animal methods for kinetics.

PubMed

Punt, Ans; Bouwmeester, Hans; Schiffelers, Marie-Jeanne W A; Peijnenburg, Ad A C M

2018-02-01

Inclusion of alternative methods that replace, reduce, or refine (3R) animal testing within regulatory safety evaluations of chemicals generally faces many hurdles. The goal of the current work is to i) collect responses from key stakeholders involved in food safety evaluations on what they consider the most relevant factors that influence the acceptance and use of 3R methods and to ii) use these responses to formulate activities needed to increase the acceptance and use of 3R methods, particularly for kinetics. The stakeholders were contacted by e-mail for their opinions, asking the respondents to write down three barriers and/or drivers and scoring these by distributing 5 points over the three factors. The main barriers that obtained the highest aggregated scores were i) uncertain predictability 3R methods/lack of validation, ii) insufficient guidance regulators/industry and iii) insufficient harmonization of legislation. The major driver identified was the possibility of 3R methods to provide more mechanistic information. Based on the results, recommendations are given to enhance the acceptance and application of 3R toxicokinetic methods in food safety evaluations. These include steering of regulatory data requirements as well as creating (funding) opportunities for development and validation of alternative methods for kinetics and development of guidances. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

Automatic recognition of coronal type II radio bursts: The ARBIS 2 method and first observations

NASA Astrophysics Data System (ADS)

Lobzin, Vasili; Cairns, Iver; Robinson, Peter; Steward, Graham; Patterson, Garth

Major space weather events such as solar flares and coronal mass ejections are usually accompa-nied by solar radio bursts, which can potentially be used for real-time space weather forecasts. Type II radio bursts are produced near the local plasma frequency and its harmonic by fast electrons accelerated by a shock wave moving through the corona and solar wind with a typi-cal speed of 1000 km s-1 . The coronal bursts have dynamic spectra with frequency gradually falling with time and durations of several minutes. We present a new method developed to de-tect type II coronal radio bursts automatically and describe its implementation in an extended Automated Radio Burst Identification System (ARBIS 2). Preliminary tests of the method with spectra obtained in 2002 show that the performance of the current implementation is quite high, ˜ 80%, while the probability of false positives is reasonably low, with one false positive per 100-200 hr for high solar activity and less than one false event per 10000 hr for low solar activity periods. The first automatically detected coronal type II radio bursts are also presented. ARBIS 2 is now operational with IPS Radio and Space Services, providing email alerts and event lists internationally.

Validation of the Parental Facilitation of Mastery Scale-II.

PubMed

Zalta, Alyson K; Allred, Kelly M; Jayawickreme, Eranda; Blackie, Laura E R; Chambless, Dianne L

2017-10-01

To develop a more reliable and comprehensive version of the Parental Facilitation of Mastery Scale (PFMS) METHOD: In Study 1, 387 undergraduates completed an expanded PFMS (PFMS-II) and measures of parenting, perceived control, responses to early life challenges, and psychopathology. In Study 2, 182 trauma-exposed community participants completed the PFMS-II and measures of perceived control, psychopathology, and well-being RESULTS: In Study 1, exploratory factor analysis of the PFMS-II revealed two factors. These factors replicated in Study 2; one item was removed to achieve measurement invariance across race. The final PFMS-II comprised a 10-item overprotection scale and a 7-item challenge scale. In both samples, this measure demonstrated good convergent and discriminant validity and was more reliable than the original PFMS. Parental challenge was a unique predictor of perceived control in both samples CONCLUSION: The PFMS-II is a valid measure of important parenting behaviors not fully captured in other measures. © 2016 Wiley Periodicals, Inc.

Identification of a New Zinc Binding Chemotype by Fragment Screening.

PubMed

Chrysanthopoulos, Panagiotis K; Mujumdar, Prashant; Woods, Lucy A; Dolezal, Olan; Ren, Bin; Peat, Thomas S; Poulsen, Sally-Ann

2017-09-14

The discovery of a new zinc binding chemotype from screening a nonbiased fragment library is reported. Using the orthogonal fragment screening methods of native state mass spectrometry and surface plasmon resonance a 3-unsubstituted 2,4-oxazolidinedione fragment was found to have low micromolar binding affinity to the zinc metalloenzyme carbonic anhydrase II (CA II). This affinity approached that of fragment sized primary benzenesulfonamides, the classical zinc binding group found in most CA II inhibitors. Protein X-ray crystallography established that 3-unsubstituted 2,4-oxazolidinediones bound to CA II via an interaction of the acidic ring nitrogen with the CA II active site zinc, as well as two hydrogen bonds between the oxazolidinedione ring oxygen and the CA II protein backbone. Furthermore, 3-unsubstituted 2,4-oxazolidinediones appear to be a viable starting point for the development of an alternative class of CA inhibitor, wherein the medicinal chemistry pedigree of primary sulfonamides has dominated for several decades.

Divergences between clinical and research methods for assessing personality disorders: implications for research and the evolution of axis II.

PubMed

Westen, D

1997-07-01

The purpose of this study was to examine the extent to which instruments for assessing axis II diverge from clinical diagnostic processes. Subjects in the first study were 52 clinicians with experience in assessment and treatment of patients with personality disorders, who were surveyed about the methods they use in clinical practice to make diagnoses and other aspects of the diagnostic process. A second study replicated the major findings with a random national sample of 1,901 experienced psychiatrists and psychologists. Whereas current instruments rely primarily on direct questions derived from DSM-IV, clinicians of every theoretical persuasion found direct questions useful for assessing axis I disorders but only marginally so for axis II. They made axis II diagnoses, instead, by listening to patients describe interpersonal interactions and observing their behavior with the interviewer. In contrast to findings with current research instruments, most patients with personality disorders in clinical practice receive only one axis II diagnosis, and if they receive more than one, one is considered primary. Clinicians reported treating a substantial number of patients for enduring personality patterns that current axis II instruments do not assess, many of which meet neither axis I nor axis II criteria, notably problems with relatedness, work, self-esteem, and chronic subclinical depressive traits. Measurements of axis II were constructed by using a model derived from axis I instruments that diverges from clinical diagnostic procedures in a way that may be problematic for the assessment of personality disorders and the development of a more clinically and empirically sound taxonomy.

Mixed Estimation for a Forest Survey Sample Design

Treesearch

Francis A. Roesch

1999-01-01

Three methods of estimating the current state of forest attributes over small areas for the USDA Forest Service Southern Research Station's annual forest sampling design are compared. The three methods were (I) simple moving average, (II) single imputation of plot data that had been updated by externally developed models, and (III) local application of a global...

Planning for Schools of Choice: Achieving Equity and Excellence. Book II--Planning Guide.

ERIC Educational Resources Information Center

Clinchy, Evans; Kolb, Frances Arick, Ed.

Designed to aid school personnel considering school choice as a possible desegregation method, this booklet explains the principles of controlled choice, presents an overall plan and flow chart, and reviews the types of organizations that might be developed. Controlled choice is a desegregation method that is voluntary, empowers parents and school…

English-as-a-Second-Language Programs in Basic Skills Education Program 1

DTIC Science & Technology

1984-01-01

languages and English as a second language . These theories and findings have led, in turn, to the development of new methods for teaching languages ...INTRODUCTION TO TEACHING TECHNIQUES FOR ENGLISH AS A SECOND LANGUAGE . . . . . . . . . . . . 9 Introduction ............................. 9 Traditional Methods ...instruments. q8 . _. ,’,..8 4% .’ II. A BRIEF INTRODUCTION TO TEACHING TECHNIQUES FOR ENGLISH

Quantification of febuxostat polymorphs using powder X-ray diffraction technique.

PubMed

Qiu, Jing-bo; Li, Gang; Sheng, Yue; Zhu, Mu-rong

2015-03-25

Febuxostat is a pharmaceutical compound with more than 20 polymorphs of which form A is most widely used and usually exists in a mixed polymorphic form with form G. In the present study, a quantification method for polymorphic form A and form G of febuxostat (FEB) has been developed using powder X-ray diffraction (PXRD). Prior to development of a quantification method, pure polymorphic form A and form G are characterized. A continuous scan with a scan rate of 3° min(-1) over an angular range of 3-40° 2θ is applied for the construction of the calibration curve using the characteristic peaks of form A at 12.78° 2θ (I/I0100%) and form G at 11.72° 2θ (I/I0100%). The linear regression analysis data for the calibration plots shows good linear relationship with R(2)=0.9985 with respect to peak area in the concentration range 10-60 wt.%. The method is validated for precision, recovery and ruggedness. The limits of detection and quantitation are 1.5% and 4.6%, respectively. The obtained results prove that the method is repeatable, sensitive and accurate. The proposed developed PXRD method can be applied for the quantitative analysis of mixtures of febuxostat polymorphs (forms A and G). Copyright © 2015 Elsevier B.V. All rights reserved.

Sorbent-embedded sheets for safe drinking water in developing countries: a case study of lead(II) removal by a zeolite-embedded sheet.

PubMed

Botoman, Lester; Shukla, Elvis; Johan, Erni; Mitsunobu, Satoshi; Matsue, Naoto

2018-02-01

Although many kinds of materials for water purification are known, easy-to-use methods that ensure the safety of drinking water for rural populations are not sufficiently available. Sorbent-embedded sheets provide methods for the easy removal of contaminants from drinking water in the home. As an example of such a sorbent-embedded sheet, we prepared a Linde type A (LTA) zeolite-embedded sheet (ZES) and examined its Pb(II) removal behaviour. Different amounts of LTA were added either as powder or as ZES to 0.3 mM Pb(NO 3 ) 2 solutions containing 2.5 mM Ca(NO 3 ) 2 , in which the ratio of the negative charges in LTA to the positive charges in Pb(II) (LTA/Pb ratio) ranged from 1 to 20. After shaking, the mixtures were centrifuged to remove the powder, while the ZES was simply removed from the mixture by hand. The LTA powder removed more than 99% of the Pb(II) from the solution at all LTA/Pb ratios within 1 h, while the ZES removed >99% of the Pb(II) at LTA/Pb ratios of 2 and higher; at the highest LTA/Pb ratio of 20, the ZES removed >99% of the Pb(II) in 30 s. Therefore, the use of appropriate sorbent-embedded sheets enable the facile removal of contaminants from water.

Using mass spectrometry to detect, differentiate, and semiquantitate closely related peptide hormones in complex milieu: measurement of IGF-II and vesiculin.

PubMed

Lee, Kate L; Middleditch, Martin J; Williams, Geoffrey M; Brimble, Margaret A; Cooper, Garth J S

2015-03-01

The search for an islet β-cell growth factor has been a key objective in recent diabetes research, because the ability to regenerate and/or protect the functioning β-cell population in patients could result in a great advancement for diabetes treatment. IGF-I and IGF-II are known to play crucial roles in fetal growth and prenatal development, and there is growing evidence that IGF-II increases β-cell proliferation and survival in vitro and in vivo. A search for the source of IGF-II-like immunoreactivity in isolated β-cell secretory granules from the murine cell line βTC6-F7 revealed a novel 2-chain IGF-II-derived peptide, which we named vesiculin and which has been shown to be a full insulin agonist. Here, we present a liquid chromatography-tandem mass spectrometry method that enables selective detection and semiquantitation of the highly related IGF-II and vesiculin molecules. We have used this method to measure these 2 peptides in conditioned media from 2 β-cell lines, produced under increasing glucose concentrations. This technique detected both IGF-II and vesiculin in media conditioned by MIN6 and βTC6-F7 cells at levels in the range of 0 to 6 μM (total insulin, 80-450 μM) and revealed a glucose-stimulated increase in insulin, IGF-II, and vesiculin. IGF-II was detected in adult human and neonatal mouse serum in high levels, but vesiculin was not present. The methodology we present herein has utility for detecting and differentiating active peptides that are highly related and of low abundance.

Preparation and nanoencapsulation of l-asparaginase II in chitosan-tripolyphosphate nanoparticles and in vitro release study

NASA Astrophysics Data System (ADS)

Bahreini, Elham; Aghaiypour, Khosrow; Abbasalipourkabir, Roghayeh; Mokarram, Ali Rezaei; Goodarzi, Mohammad Taghi; Saidijam, Massoud

2014-07-01

This paper describes the production, purification, and immobilization of l-asparaginase II (ASNase II) in chitosan nanoparticles (CSNPs). ASNase II is an effective antineoplastic agent, used in the acute lymphoblastic leukemia chemotherapy. Cloned ASNase II gene ( ansB) in pAED4 plasmid was transformed into Escherichia coli BL21pLysS (DE3) competent cells and expressed under optimal conditions. The lyophilized enzyme was loaded into CSNPs by ionotropic gelation method. In order to get optimal entrapment efficiency, CSNP preparation, chitosan/tripolyphosphate (CS/TPP) ratio, and protein loading were investigated. ASNase II loading into CSNPs was confirmed by Fourier transform infrared (FTIR) spectroscopy, and morphological observation was carried out by transmission electron microscopy. Three absolute CS/TPP ratios were studied. Entrapment efficiency and loading capacity increased with increasing CS and TPP concentration. The best ratio was applied for obtaining optimal ASNase II-loaded CSNPs with the highest entrapment efficiency. Size, zeta potential, entrapment efficiency, and loading capacity of the optimal ASNase II-CSNPs were 340 ± 12 nm, 21.2 ± 3 mV, 76.2% and 47.6%, respectively. The immobilized enzyme showed an increased in vitro half-life in comparison with the free enzyme. The pH and thermostability of the immobilized enzyme was comparable with the free enzyme. This study leads to a better understanding of how to prepare CSNPs, how to achieve high encapsulation efficiency for a high molecular weight protein, and how to prolong the release of protein from CSNPs. A conceptual understanding of biological responses to ASNase II-loaded CSNPs is needed for the development of novel methods of drug delivery.

Determination of mercury (II) ions based on silver-nanoparticles-assisted growth of gold nanostructures: UV-Vis and surface enhanced Raman scattering approaches

NASA Astrophysics Data System (ADS)

Chen, Jun-Liang; Yang, Pei-Chia; Wu, Tsunghsueh; Lin, Yang-Wei

2018-06-01

Innovative dual detection methods for mercury(II) ions (Hg(II)) have been developed based on the formation of gold nanostructures (AuNSs) following the addition of mercury-containing solution to a mixture containing an optimized amount of Au(III), H2O2, HCl, and silver nanoparticles (AgNPs). In the absence of Hg(II), the addition of Au(III), H2O2, and HCl to the AgNP solution changes the solution's color from yellow to red, and the absorption peak shifts from 400 to 526 nm, indicating the dissolution of AgNPs and the formation of gold nanoparticles (AuNPs). Because of the spontaneous redox reaction of Hg(II) toward AgNPs, the change in the amount of remaining AgNP seed facilitates the generation of irregular AuNSs, resulting in changes in absorption intensity and shifting the peak within the range from 526 to 562 nm depending on the concentration of Hg(II). Under optimal conditions, the limit of detection (LOD) for Hg(II) at a signal-to-noise ratio (S/N) of 3 was 0.3 μM. We further observed that AgNP-assisted catalytic formation of Au nanomaterials deposited on a surface enhanced Raman scattering active substrate significantly reduced the Raman signal of 4-mercaptobenzoic acid, dependent on the Hg(II) concentration. A linear relationship was observed in the range 0.1 nM-100 μM with a LOD of 0.05 nM (S/N 3.0). As a simple, accurate and precise method, this SERS-based assay has demonstrated its success in determining levels of Hg(II) in real water samples.

Current progress of targetron technology: development, improvement and application in metabolic engineering.

PubMed

Liu, Ya-Jun; Zhang, Jie; Cui, Gu-Zhen; Cui, Qiu

2015-06-01

Targetrons are mobile group II introns that can recognize their DNA target sites by base-pairing RNA-DNA interactions with the aid of site-specific binding reverse transcriptases. Targetron technology stands out from recently developed gene targeting methods because of the flexibility, feasibility, and efficiency, and is particularly suitable for the genetic engineering of difficult microorganisms, including cellulolytic bacteria that are considered promising candidates for biomass conversion via consolidated bioprocessing. Along with the development of the thermotargetron method for thermophiles, targetron technology becomes increasingly important for the metabolic engineering of industrial microorganisms aiming at biofuel/chemical production. To summarize the current progress of targetron technology and provide new insights on the use of the technology, this paper reviews the retrohoming mechanisms of both mesophilic and thermophilic targetron methods based on various group II introns, investigates the improvement of targetron tools for high target efficiency and specificity, and discusses the current applications in the metabolic engineering for bacterial producers. Although there are still intellectual property and technical restrictions in targetron applications, we propose that targetron technology will contribute to both biochemistry research and the metabolic engineering for industrial productions. Copyright © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

High-performance liquid chromatographic determination of 4,4'-dihydroxybenzophenone-2,4-dinitrophenylhydrazone in plasma.

PubMed

Rodgers, A H; Subramanian, S; Morgan, L R

1995-08-18

An analytical method has been developed for the determination of 4,4'-dihydroxybenzophenone-2,4-dinitrophenylhydrazone (I, trade name A-007) in plasma. Plasma samples are primed with the internal standard, 2,2'-dihydroxybenzophenone-2,4-dinitrophenylhydrazone (II), deproteinized with acetonitrile, centrifuged and filtered prior to assay. The components are then separated on a reversed-phase column with retention times of 4.4 and 6.0 min for I and II, respectively. Ultraviolet detection at 365 nm was employed and little interference with the analyte or the internal standard was noted from other plasma components. This method has been applied to the plasma of rats and monkeys doses for pharmacokinetic and toxicity studies.

A study: Effect of Students Peer Assisted Learning on Magnetic Field Achievement

NASA Astrophysics Data System (ADS)

Mueanploy, Wannapa

2016-04-01

This study is the case study of Physic II Course for students of Pathumwan Institute of Technology. The purpose of this study is: 1) to develop cooperative learning method of peer assisted learning (PAL), 2) to compare the learning achievement before and after studied magnetic field lesson by cooperative learning method of peer assisted learning. The population was engineering students of Pathumwan Institute of Technology (PIT’s students) who registered Physic II Course during year 2014. The sample used in this study was selected from the 72 students who passed in Physic I Course. The control groups learning magnetic fields by Traditional Method (TM) and experimental groups learning magnetic field by method of peers assisted learning. The students do pretest before the lesson and do post-test after the lesson by 20 items achievement tests of magnetic field. The post-test higher than pretest achievement significantly at 0.01 level.

Description and pilot results from a novel method for evaluating return of incidental findings from next-generation sequencing technologies.

PubMed

Goddard, Katrina A B; Whitlock, Evelyn P; Berg, Jonathan S; Williams, Marc S; Webber, Elizabeth M; Webster, Jennifer A; Lin, Jennifer S; Schrader, Kasmintan A; Campos-Outcalt, Doug; Offit, Kenneth; Feigelson, Heather Spencer; Hollombe, Celine

2013-09-01

The aim of this study was to develop, operationalize, and pilot test a transparent, reproducible, and evidence-informed method to determine when to report incidental findings from next-generation sequencing technologies. Using evidence-based principles, we proposed a three-stage process. Stage I "rules out" incidental findings below a minimal threshold of evidence and is evaluated using inter-rater agreement and comparison with an expert-based approach. Stage II documents criteria for clinical actionability using a standardized approach to allow experts to consistently consider and recommend whether results should be routinely reported (stage III). We used expert opinion to determine the face validity of stages II and III using three case studies. We evaluated the time and effort for stages I and II. For stage I, we assessed 99 conditions and found high inter-rater agreement (89%), and strong agreement with a separate expert-based method. Case studies for familial adenomatous polyposis, hereditary hemochromatosis, and α1-antitrypsin deficiency were all recommended for routine reporting as incidental findings. The method requires <3 days per topic. We establish an operational definition of clinically actionable incidental findings and provide documentation and pilot testing of a feasible method that is scalable to the whole genome.

Assessment of personality disorders in anorexia nervosa and bulimia nervosa. A comparison of self-report and structured interview methods.

PubMed

Kennedy, S H; Katz, R; Rockert, W; Mendlowitz, S; Ralevski, E; Clewes, J

1995-06-01

Interest in assessing Personality Disorders (PDs) in association with anorexia nervosa (AN) and bulimia nervosa (BN) has been accompanied by the development of several structured interview and self-report measures. In an attempt to see how the self-report Millon Clinical Multiaxial Inventory (MCMI-II) compared with the Structured Clinical Interview for DSM-III-R (SCID-II) in the assessment of PDs, we gave both instruments to 43 inpatients with a diagnosis of AN or BN. Correlation coefficient values for both categorical and dimensional comparisons were generally less than .4. Although comparable rates of positive PDs occurred for each of the three clusters (A: 30.2% vs. 34.9%, B: 25.6% vs. 18.6%, and C: 62.8% vs. 81.4% for SCID-II vs. MCMI-II), agreement for individual diagnosis and individual subjects was poor. In conclusion, the MCMI-II did not prove to be a reliable instrument for assessing axis II PDs in patients with AN and BN when compared with the SCID-II.

Azobenzene Pd(II) complexes with N^N- and N^O-type ligands

NASA Astrophysics Data System (ADS)

Nikolaeva, M. V.; Puzyk, An. M.; Puzyk, M. V.

2017-05-01

Methods of synthesis of cyclometalated azobenzene palladium(II) complexes of [Pd(N^N)Azb]ClO4 and [Pd(N^O)Azb]ClO4 types (where Azb- is the deprotonated form of azobenzene; N^N is 2NH3, ethylenediamine, or 2,2'-bipyridine; and (N^O)- is the deprotonated form of amino acid (glycine, α-alanine, β-alanine, tyrosine, or tryptophan)) are developed. The electronic absorption and the electrochemical properties of these complexes are studied.

The 'retro-design' concept for novel kinase inhibitors.

PubMed

Müller, Gerhard; Sennhenn, Peter C; Woodcock, Timothy; Neumann, Lars

2010-07-01

Protein kinases are among the most attractive therapeutic targets for a broad range of diseases. This feature review highlights and classifies the main design principles employed to generate active and selective kinase inhibitors. In particular, emphasis is focused on a fragment-based lead-generation approach, which constitutes a novel design method for developing type II kinase inhibitors with distinct binding kinetic attributes. This 'retro-design' strategy relies on a customized fragment library, and contrasts the traditional approach used in the design of type II inhibitors.

Dithizone-modified graphene oxide nano-sheet as a sorbent for pre-concentration and determination of cadmium and lead ions in food.

PubMed

Moghadam Zadeh, Hamid Reza; Ahmadvand, Parvaneh; Behbahani, Ali; Amini, Mostafa M; Sayar, Omid

2015-01-01

Graphene oxide nano-sheet was modified with dithizone as a novel sorbent for selective pre-concentration and determination of Cd(II) and Pb(II) in food. The sorbent was characterised by various analytical methods and the effective parameters for Cd(II) and Pb(II) adsorption were optimised during this work. The high adsorption capacity and selectivity of this sorbent makes the method capable of fast determinations of the Cd(II) and Pb(II) content in complicated matrices even at μg l(-1) levels using commonly available instrumentation. The precision of this method was < 1.9% from 10 duplicate determinations and its accuracy verified using standard reference materials. Finally, this method was applied to the determination of Cd(II) and Pb(II) ions in common food samples and satisfactory results were obtained.

Air Force Maintenance Technician Performance Measurement.

DTIC Science & Technology

1979-12-28

R G A N I Z A T IO N N A M E A N D A D R S A R E A P HO R U I T N U M B E R AFIT STUDENT AT: Arizona State Univ II. CONTROLLING OFFICE NAME AND...inflated, or provide incomplete and non -current coverage of maintenance organizations. The performance aopraisal method developed relies on subjective...highly inflated, or provided incomplete and non -current coverage of maintenance organizations. The performance appraisal method developed relied on

Comparative evaluation of concrete bridge deck sealers.

DOT National Transportation Integrated Search

2015-08-01

The main objective of this research was to compare the performance of five bridge deck sealer products using a : synthesis of two testing methods: NCHRP Report 244 Series II tests and standards developed by the Alberta : Ministry of Transportation (B...

40 CFR 35.700 - Purpose.

Code of Federal Regulations, 2011 CFR

2011-07-01

... residential construction types); (ii) Development of public information and education materials concerning... management system for information concerning radon occurrence, levels, and programs; (ix) Payment of costs of demonstration of radon mitigation methods and technologies as approved by EPA, including Tribal and Intertribal...

40 CFR 35.700 - Purpose.

Code of Federal Regulations, 2012 CFR

2012-07-01

... residential construction types); (ii) Development of public information and education materials concerning... management system for information concerning radon occurrence, levels, and programs; (ix) Payment of costs of demonstration of radon mitigation methods and technologies as approved by EPA, including Tribal and Intertribal...

On-line high-speed rail defect detection : part II.

DOT National Transportation Integrated Search

2012-03-01

The objectives of this project were (1) to improve the defect detection reliability and (2) to improve the inspection speed of conventional rail defect detection methods. The prototype developed in this work uses noncontact transducers, ultrasonic gu...

The use of FTIR microscopy for evaluation of herpes viruses infection development kinetics

NASA Astrophysics Data System (ADS)

Erukhimovitch, Vitaly; Mukmanov, Igor; Talyshinsky, Marina; Souprun, Yelena; Huleihel, Mahmoud

2004-08-01

The kinetics of Herpes simplex infection development was studied using an FTIR microscopy (FTIR-M) method. The family of herpes viruses includes several members like H. simplex types I and II (HSV I, II), Varicella zoster (VZV) viruses which are involved in various human and animal infections of different parts of the body. In our previous study, we found significant spectral differences between normal uninfected cells in cultures and cells infected with herpes viruses at early stages of the infection. In the present study, cells in cultures were infected with either HSV-I or VZV and at various times post-infection they were examined either by optical microscopy or by advanced FTIR-M. Spectroscopic measurements show a consistent decrease in the intensity of the carbohydrate peak in correlation with the viral infection development, observed by optical microscopy. This decrease in cellular carbohydrate level was used as indicator for herpes viruses infection kinetics. This parameter could be used as a basis for applying a spectroscopic method for the evaluation of herpes virus infection development. Our results show also that the development kinetics of viral infection has an exponential character for these viruses.

Novel total antioxidant capacity index for dietary polyphenols and vitamins C and E, using their cupric ion reducing capability in the presence of neocuproine: CUPRAC method.

PubMed

Apak, Resat; Güçlü, Kubilay; Ozyürek, Mustafa; Karademir, Saliha Esin

2004-12-29

The chemical diversity of antioxidants makes it difficult to separate and quantify antioxidants from the vegetable matrix. Therefore, it is desirable to establish a method that can measure the total antioxidant activity level directly from vegetable extracts. The current literature clearly states that there is no "total antioxidant" as a nutritional index available for food labeling because of the lack of standard quantitation methods. Thus, this work reports the development of a simple, widely applicable antioxidant capacity index for dietary polyphenols and vitamins C and E, utilizing the copper(II)-neocuproine [Cu(II)-Nc] reagent as the chromogenic oxidizing agent. Because the copper(II) (or cupric) ion reducing ability of polyphenols is measured, the method is named by our research group "cupric reducing antioxidant capacity" abbreviated as the CUPRAC method. This method should be advantageous over the ferric reducing antioxidant power (FRAP) method because the redox chemistry of copper(II)-as opposed to that of ferric ion-involves faster kinetics. The method comprises mixing of the antioxidant solution (directly or after acid hydrolysis) with a copper(II) chloride solution, a neocuproine alcoholic solution, and an ammonium acetate aqueous buffer at pH 7 and subsequent measurement of the developed absorbance at 450 nm after 30 min. Because the color development is fast for compounds such as ascorbic acid, gallic acid, and quercetin but slow for naringin and naringenin, the latter compounds were assayed after incubation at 50 degrees C on a water bath for 20 min [after Cu(II)-Nc reagent addition] so as to force the oxidation reaction to reach completion. The flavonoid glycosides were hydrolyzed to their corresponding aglycons by refluxing in 1.2 M HCl-containing 50% MeOH so as to exert maximal reducing power toward Cu(II)-Nc. Certain compounds also needed incubation after acid hydrolysis to fully exhibit their reducing capability. The CUPRAC antioxidant capacities of synthetic mixtures of antioxidants were experimentally measured as Trolox equivalents and compared to those theoretically found by making use of the principle of additivity of absorbances assuming no chemical interaction between the mixture constituents. Because ascorbic acid is not resistant to elevated temperature incubation, it should be assayed initially by measuring the absorbance (at 450 nm) difference of original and ascorbate oxidase-added mixture solutions at the end of 1 min of Cu(II)-Nc reagent addition. Thus, the total CUPRAC antioxidant capacity of a mixture containing various antioxidants should be that finally measured after a suitable combination of hydrolysis and incubation procedures, added to the initially measured capacity due to ascorbate. The antioxidant polyphenolic compounds tested demonstrate that the highest capacities in the CUPRAC method were observed for epicatechin gallate, epigallocatechin gallate, quercetin, fisetin, epigallocatechin, catechin, and caffeic acid in this order, in accordance with theoretical expectations, because the number and position of the hydroxyl groups as well as the degree of conjugation of the whole molecule are important. The antioxidant potency of flavonoids is nearly proportional to the total number of -OH groups and is positively affected by the presence of an o-dihydroxy moiety in the B-ring. beta-Carotene, which did not react with the CUPRAC reagent in alcoholic aqueous medium, could be assayed in dichloromethane solvent. Linear calibration curves for ascorbic acid and flavonoids were redrawn in synthetic solutions containing a mixture of antioxidants, and also in real matrices such as grape and orange juices, green tea, and blackberry tea, showing an initial nonzero absorbance with the CUPRAC reagent. The parallellism of the linear calibration curves of pure compounds in a given complex matrix effectively demonstrated that there were no interferent chemical interactions among the solution constituents and that the antioxidant capacities of the tested antioxidants were additive. The CUPRAC reagent is reasonably selective, stable, easily accessible, and sensitive toward thiol-type oxidants, unlike the FRAP method. The reaction is carried out at nearly physiological pH as opposed to the unrealistic acidic pH of FRAP.

O-GlcNAcPRED-II: an integrated classification algorithm for identifying O-GlcNAcylation sites based on fuzzy undersampling and a K-means PCA oversampling technique.

PubMed

Jia, Cangzhi; Zuo, Yun; Zou, Quan; Hancock, John

2018-02-06

Protein O-GlcNAcylation (O-GlcNAc) is an important post-translational modification of serine (S)/threonine (T) residues that involves multiple molecular and cellular processes. Recent studies have suggested that abnormal O-G1cNAcylation causes many diseases, such as cancer and various neurodegenerative diseases. With the available protein O-G1cNAcylation sites experimentally verified, it is highly desired to develop automated methods to rapidly and effectively identify O-G1cNAcylation sites. Although some computational methods have been proposed, their performance has been unsatisfactory, particularly in terms of prediction sensitivity. In this study, we developed an ensemble model O-GlcNAcPRED-II to identify potential O-G1cNAcylation sites. A K-means principal component analysis oversampling technique (KPCA) and fuzzy undersampling method (FUS) were first proposed and incorporated to reduce the proportion of the original positive and negative training samples. Then, rotation forest, a type of classifier-integrated system, was adopted to divide the eight types of feature space into several subsets using four sub-classifiers: random forest, k-nearest neighbour, naive Bayesian and support vector machine. We observed that O-GlcNAcPRED-II achieved a sensitivity of 81.05%, specificity of 95.91%, accuracy of 91.43% and Matthew's correlation coefficient of 0.7928 for five-fold cross-validation run 10 times. Additionally, the results obtained by O-GlcNAcPRED-II on two independent datasets also indicated that the proposed predictor outperformed five published prediction tools. http://121.42.167.206/OGlcPred/. cangzhijia@dlmu.edu.cn or zouquan@nclab.net. © The Author (2018). Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com

Development, validation and application of the liquid chromatography tandem mass spectrometry method for simultaneous quantification of azilsartan medoxomil (TAK-491), azilsartan (TAK-536), and its 2 metabolites in human plasma.

PubMed

Kuze, Yoji; Kogame, Akifumi; Jinno, Fumihiro; Kondo, Takahiro; Asahi, Satoru

2015-09-15

Azilsartan medoxomil potassium salt (TAK-491) is an orally administered angiotensin II type 1 receptor blocker for the treatment of hypertension and is an ester-based prodrug that is rapidly hydrolyzed to the pharmacologically active moiety, azilsartan (TAK-536), during absorption. TAK-536 is biotransformed to the 2 metabolites M-I by decarboxylation and M-II by dealkylation. In this study, we developed and validated a LC/MS/MS method which can simultaneously determine 4 analytes, TAK-491, TAK-536, M-I and M-II. The bioanalytical method can be outlined as follows: two structural analogues are used as the internal standards. The analytes and the IS are extracted from human plasma using solid phase extraction. After evaporating, the residue is reconstituted and injected into a LC/MS/MS system with an ESI probe and analyzed in the positive ion mode. Separation is performed through a conventional reversed-phase column with a mobile phase of water/acetonitrile/acetic acid (40:60:0.05, v/v/v) mixture at a flow rate of 0.2mL/min. The total run time is 8.5min. The calibration range is 1-2500ng/mL in human plasma for all the analytes. Instability issues of the prodrug, TAK-491, were overcome and all the validation results met the acceptance criteria in accordance with the regulatory guideline/guidance. As a result of the clinical study, the human PK profiles of TAK-536, M-I and M-II were successfully obtained and also it was confirmed that TAK-491 was below the LLOQ (1ng/mL) in the human plasma samples. Copyright © 2015 Elsevier B.V. All rights reserved.

Flame Atomic Absorption Spectrometric Determination of Trace Metal Ions in Environmental and Biological Samples After Preconcentration on a Newly Developed Amberlite XAD-16 Chelating Resin Containing p-Aminobenzene Sulfonic Acid.

PubMed

Islam, Aminul; Ahmad, Akil; Laskar, Mohammad Asaduddin

2015-01-01

Amberlite® XAD-16 was functionalized with p-aminobenzene sulfonic acid via an azo spacer in order to prepare a new chelating resin, which was then characterized by water regain value, hydrogen ion capacity, elemental analyses, and IR spectral and thermal studies. The maximum uptake of Cu(II), Ni(II), Zn(II), Co(II), Cr(III), Fe(III), and Pb(II) ions was observed in the pH range 4.0-6.0 with the corresponding half-loading times of 6.5, 7.0, 8.0, 9.0, 11.0, 8.5, and 16.5 min. The sorption data followed Langmuir isotherms and a pseudo-second-order model. Thermodynamic quantities, ΔH and ΔS, based on the variation of the distribution coefficient with temperature were also evaluated. High preconcentration factors of 60-100 up to a low preconcentration limit of 4.0-6.6 μg/L have been achieved for the metal ions. The validity of the method was checked by analyzing standard reference materials and recoveries of trace metals after spiking. The analytical applications of the method were explored by analyzing natural water, mango pulp, mint leaves, and fish.

Heavy metal contents of play dough, face and finger paint samples sold in turkish markets.

PubMed

Erbas, Zeliha; Karatepe, Aslihan; Soylak, Mustafa

2017-08-01

Lead, cadmium, nickel, manganese, cobalt and copper contents of some play dough, face and finger paint samples were determined by using a new solid phase extraction method which has been developed by using multi-walled carbon nanotube with patent blue (V) sodium salt to selectively separate and preconcentrate these metal ions. Flame atomic absorption spectrometry was used to determine the metal ions. Analytical parameters affecting the complex formation and solid phase extraction performance such as pH, the amount of ligand and volume of sample solution were investigated. The recoveries of the studied metal ions were not affected by the foreign ions. Analytes were recovered quantitatively at pH 5.5 and with a nitric acid of 2molL -1 as eluent. Analysis of a certified reference material was performed to validate the method before applying it to determine the metal ions in the real samples. Detection limits were found to be as Pb(II): 7.71μgL -1 , Cu(II): 1.43μgL -1 , Cd(III): 0.21μgL -1 , Mn(II): 0.47μgL -1 , Ni(II): 3.52μgL -1 and Co(II): 1.96μgL -1 . Copyright © 2017 Elsevier B.V. All rights reserved.

Rapid and efficient removal of Pb(II) from aqueous solutions using biomass-derived activated carbon with humic acid in-situ modification.

PubMed

Guo, Zizhang; Zhang, Jian; Kang, Yan; Liu, Hai

2017-11-01

This study developed an humic acid (HA) in-situ modified activated carbon adsorbent (AC-HA) for the rapid and efficient removal of Pb(II) from aqueous media, and adsorption mechanisms are discussed. The physicochemical characteristics of activated carbons (AC) were investigated via N 2 adsorption/desorption, scanning electron microscopy (SEM), Boehm's titration method and Fourier transform infrared spectroscopy (FTIR). AC-HA exhibited richer oxygen-containing functional groups than the original AC. In addition, the removal performance of AC-HA (250.0mg/g) toward Pb(II) was greatly improved compared with the original AC (166.7mg/g). The batch adsorption study results revealed that the Pb(II) adsorption data were best fit by the pseudo-second-order model of kinetics and Langmuir isotherm of isothermals, and therefore, the effect of the solution pH was studied. The superior performance of AC-HA was attributed to the HA modification, which contains numbers of groups and has a strong π-π interaction binding energy with AC and Pb(II) species. The adsorption mechanisms were confirmed via the XPS study. More importantly, the modified method is simple and has a low cost of production. Copyright © 2017 Elsevier Inc. All rights reserved.

Guidelines for clinical use of CBCT: a review

PubMed Central

O'Malley, L; Taylor, K; Glenny, A-M

2015-01-01

Objectives: To identify guidelines on the clinical use of CBCT in dental and maxillofacial radiology, in particular selection criteria, to consider how they were produced, to appraise their quality objectively and to compare their recommendations. Methods: A literature search using MEDLINE (Ovid®) was undertaken prospectively from 1 January 2000 to identify published material classifiable as “guidelines” pertaining to the use of CBCT in dentistry. This was supplemented by searches on websites, an internet search engine, hand searching of theses and by information from personal contacts. Quality assessment of publications was performed using the AGREE II instrument. Publications were examined for areas of agreement and disagreement. Results: 26 publications were identified, 11 of which were specifically written to give guidelines on the clinical use of CBCT and contained sections on selection criteria. The remainder were a heterogeneous mixture of publications that included guidelines relating to CBCT. Two had used a formal evidence-based approach for guideline development and two used consensus methods. The quality of publications was frequently low as assessed using AGREE II, with many lacking evidence of adequate methodology. There was broad agreement between publications on clinical use, apart from treatment planning, in implant dentistry. Conclusions: Reporting of guideline development is often poorly presented. Guideline development panels should aim to perform and report their work using the AGREE II instrument as a template to raise standards and avoid the risk of suspicions of bias. PMID:25270063

Flow Injection Photochemical Vapor Generation Coupled with Miniaturized Solution-Cathode Glow Discharge Atomic Emission Spectrometry for Determination and Speciation Analysis of Mercury.

PubMed

Mo, Jiamei; Li, Qing; Guo, Xiaohong; Zhang, Guoxia; Wang, Zheng

2017-10-03

A novel, compact, and green method was developed for the determination and speciation analysis of mercury, based on flow injection photochemical vapor generation (PVG) coupled with miniaturized solution cathode glow discharge-atomic emission spectroscopy (SCGD-AES). The SCGD was generated between a miniature hollow titanium tube and a solution emerging from a glass capillary. Cold mercury vapor (Hg(0)) was generated by PVG and subsequently delivered to the SCGD for excitation, and finally the emission signals were recorded by a miniaturized spectrograph. The detection limits (DLs) of Hg(II) and methylmercury (MeHg) were both determined to be 0.2 μg L -1 . Moreover, mercury speciation analysis could also be performed by using different wavelengths and powers from the UV lamp and irradiation times. Both Hg(II) and MeHg can be converted to Hg(0) for the determination of total mercury (T-Hg) with 8 W/254 nm UV lamp and 60 s irradiation time; while only Hg(II) can be reduced to Hg(0) and determined selectively with 4 W/365 nm UV lamp and 20 s irradiation time. Then, the concentration of MeHg can be calculated by subtracting the Hg(II) from the T-Hg. Because of its similar sensitivity and DL at 8 W/254 nm, the simpler and less toxic Hg(II) was used successfully as a primary standard for the quantification of T-Hg. The novel PVG-SCGD-AES system provides not only a 365-fold improvement in the DL for Hg(II) but also a nonchromatographic method for the speciation analysis of mercury. After validating its accuracy, this method was successfully used for mercury speciation analysis of water and biological samples.

Rural self-reliance: the impact on health experiences of people living with type II diabetes in rural Queensland, Australia

PubMed Central

Page-Carruth, Althea; Windsor, Carol; Clark, Michele

2014-01-01

Objective The objective of the study was to explore whether and how rural culture influences type II diabetes management and to better understand the social processes that rural people construct in coping with diabetes and its complications. In particular, the study aimed to analyse the interface and interactions between rural people with type II diabetes and the Australian health care system, and to develop a theoretical understanding that reflects constructs that may be more broadly applicable. Methods The study applied constructivist grounded theory methods within an interpretive interactionist framework. Data from 39 semi-structured interviews with rural and urban type II diabetes patients and a mix of rural health care providers were analysed to develop a theoretical understanding of the social processes that define diabetes management in that context. Results The analysis suggests that although type II diabetes imposes limitations that require adjustment and adaptation, these processes are actively negotiated by rural people within the environmental context to fit the salient social understandings of autonomy and self-reliance. Thus, people normalized self-reliant diabetes management behaviours because this was congruent with the rural culture. Factors that informed the actions of normalization were relationships between participants and health care professionals, support, and access to individual resources. Conclusions The findings point to ways in which rural self-reliance is conceived as the primary strategy of diabetes management. People face the paradox of engaging with a health care system that at the same time maximizes individual responsibility for health and minimizes the social support by which individuals manage the condition. The emphasis on self-reliance gives some legitimacy to a lack of prevention and chronic care services. Success of diabetes management behaviours is, however, contingent on relative resources. Where there is good primary care, there develops a number of downstream effects including a sense of empowerment to manage difficult rural environmental circumstances. This has particular bearing on health outcomes for people with fewer resources. PMID:24964859

Derivatization of labetalol hydrochloride for its spectrofluorimetric and spectrophotometric determination inhuman plasma: Application to stability study

NASA Astrophysics Data System (ADS)

Omar, Mahmoud A.; Derayea, Sayed M.; Abdel-Lateef, Mohamed A.; El Hamd, Mohamed A.

2018-02-01

Two simple, selective and accurate methods were developed for the determination of Labetalol hydrochloride in pure form and pharmaceutical tablets. Both methods are based on derivatization of the studied drug with 4-chloro-7-nitrobenzo-2-oxa-1,3-diazole (NBDsbnd Cl) in alkaline medium (pH 7.5).The reaction product was measured spectrofluorimetrically at 540 nm after excitation at 476 nm (method I) or spectrophotometrically at 480 nm (method II). The calibration graphs were rectilinear over the concentration ranges of 0.10-2.0 and 1.0-11.0 μg mL- 1 for methods I and II, respectively. The proposed methods were successfully applied to the analysis of commercial tablets without interference from common excipients. Furthermore, the spectrofluorimetric method was utilized for the in vitro determination of labetalol in spiked human plasma, with a percent mean recovery (n = 3) of 97.80 ± 1.29%. Moreover, the spectrofluorimetric method was extended to examine the stability study of LBT under different stress conditions such as alkaline, acidic, oxidative, photolytic and a thermal degradation.

Studies of EXAFSSpectra using Copper (II) Schiff Base complexes and Determination of Bond lengths Using Synchrotron Radiation

NASA Astrophysics Data System (ADS)

Mishra, A.; Vibhute, V.; Ninama, S.; Parsai, N.; Jha, S. N.; Sharma, P.

2016-10-01

X-ray absorption fine structure (XAFS) at the K-edge of copper has been studied in some copper (II) complexes with substituted anilines like (2Cl, 4Br, 2NO2, 4NO2 and pure aniline) with o-PDA (orthophenylenediamine) as ligand. The X-ray absorption measurements have been performed at the recently developed BL-8 dispersive EXAFS beam line at 2.5 GeV Indus-2 Synchrotron Source at RRCAT, Indore, India. The data obtained has been processed using EXAFS data analysis program Athena.The graphical method gives the useful information about bond length and also the environment of the absorbing atom. The theoretical bond lengths of the complexes were calculated by using interactive fitting of EXAFS using fast Fourier inverse transformation (IFEFFIT) method. This method is also called as Fourier transform method. The Lytle, Sayers and Stern method and Levy's method have been used for determination of bond lengths experimentally of the studied complexes. The results of both methods have been compared with theoretical IFEFFIT method.

Derivatization of labetalol hydrochloride for its spectrofluorimetric and spectrophotometric determination inhuman plasma: Application to stability study.

PubMed

Omar, Mahmoud A; Derayea, Sayed M; Abdel-Lateef, Mohamed A; El Hamd, Mohamed A

2018-02-05

Two simple, selective and accurate methods were developed for the determination of Labetalol hydrochloride in pure form and pharmaceutical tablets. Both methods are based on derivatization of the studied drug with 4-chloro-7-nitrobenzo-2-oxa-1,3-diazole (NBDCl) in alkaline medium (pH7.5).The reaction product was measured spectrofluorimetrically at 540nm after excitation at 476nm (method I) or spectrophotometrically at 480nm (method II). The calibration graphs were rectilinear over the concentration ranges of 0.10-2.0 and 1.0-11.0μgmL -1 for methods I and II, respectively. The proposed methods were successfully applied to the analysis of commercial tablets without interference from common excipients. Furthermore, the spectrofluorimetric method was utilized for the in vitro determination of labetalol in spiked human plasma, with a percent mean recovery (n=3) of 97.80±1.29%. Moreover, the spectrofluorimetric method was extended to examine the stability study of LBT under different stress conditions such as alkaline, acidic, oxidative, photolytic and a thermal degradation. Copyright © 2017 Elsevier B.V. All rights reserved.

Analysis of full disc Ca II K spectroheliograms. I. Photometric calibration and centre-to-limb variation compensation

NASA Astrophysics Data System (ADS)

Chatzistergos, Theodosios; Ermolli, Ilaria; Solanki, Sami K.; Krivova, Natalie A.

2018-01-01

Context. Historical Ca II K spectroheliograms (SHG) are unique in representing long-term variations of the solar chromospheric magnetic field. They usually suffer from numerous problems and lack photometric calibration. Thus accurate processing of these data is required to get meaningful results from their analysis. Aims: In this paper we aim at developing an automatic processing and photometric calibration method that provides precise and consistent results when applied to historical SHG. Methods: The proposed method is based on the assumption that the centre-to-limb variation of the intensity in quiet Sun regions does not vary with time. We tested the accuracy of the proposed method on various sets of synthetic images that mimic problems encountered in historical observations. We also tested our approach on a large sample of images randomly extracted from seven different SHG archives. Results: The tests carried out on the synthetic data show that the maximum relative errors of the method are generally <6.5%, while the average error is <1%, even if rather poor quality observations are considered. In the absence of strong artefacts the method returns images that differ from the ideal ones by <2% in any pixel. The method gives consistent values for both plage and network areas. We also show that our method returns consistent results for images from different SHG archives. Conclusions: Our tests show that the proposed method is more accurate than other methods presented in the literature. Our method can also be applied to process images from photographic archives of solar observations at other wavelengths than Ca II K.

Conflagration Analysis System II: Bibliography.

DTIC Science & Technology

1985-04-01

Therefore, it is Lmportant to examine both the reinforcement and the supplemental considerations Eor the quantitative methods for conflagration...and the meaningful quantitative factors for conflagration analysis are determined, the relevatn literature will be brought into the nainstream of the... quantitative :hods. Fire Development in Multiple Structures From a purely analytical view, the research identified in the literature fire development in

Rural Development in Africa: A Bibliography (Part II: North, South, West). Training & Methods Series, Number 17.

ERIC Educational Resources Information Center

Wisconsin Univ., Madison. Land Tenure Center.

Compiled in December 1971, this bibliography lists approximately 940 books, journals, periodicals, and unpublished mimeographs dealing with rural development in north, west, and southern Africa. All materials are dated between 1953 and 1971. Entries are listed by country under the following headings: agriculture, economic affairs, social affairs,…

Identification of homemade inorganic explosives by ion chromatographic analysis of post-blast residues.

PubMed

Johns, Cameron; Shellie, Robert A; Potter, Oscar G; O'Reilly, John W; Hutchinson, Joseph P; Guijt, Rosanne M; Breadmore, Michael C; Hilder, Emily F; Dicinoski, Greg W; Haddad, Paul R

2008-02-29

Anions and cations of interest for the post-blast identification of homemade inorganic explosives were separated and detected by ion chromatographic (IC) methods. The ionic analytes used for identification of explosives in this study comprised 18 anions (acetate, benzoate, bromate, carbonate, chlorate, chloride, chlorite, chromate, cyanate, fluoride, formate, nitrate, nitrite, perchlorate, phosphate, sulfate, thiocyanate and thiosulfate) and 12 cations (ammonium, barium(II), calcium(II), chromium(III), ethylammonium, magnesium(II), manganese(II), methylammonium, potassium(I), sodium(I), strontium(II), and zinc(II)). Two IC separations are presented, using suppressed IC on a Dionex AS20 column with potassium hydroxide as eluent for anions, and non-suppressed IC for cations using a Dionex SCS 1 column with oxalic acid/acetonitrile as eluent. Conductivity detection was used in both cases. Detection limits for anions were in the range 2-27.4ppb, and for cations were in the range 13-115ppb. These methods allowed the explosive residue ions to be identified and separated from background ions likely to be present in the environment. Linearity (over a calibration range of 0.05-50ppm) was evaluated for both methods, with r(2) values ranging from 0.9889 to 1.000. Reproducibility over 10 consecutive injections of a 5ppm standard ranged from 0.01 to 0.22% relative standard deviation (RSD) for retention time and 0.29 to 2.16%RSD for peak area. The anion and cation separations were performed simultaneously by using two Dionex ICS-2000 chromatographs served by a single autoinjector. The efficacy of the developed methods was demonstrated by analysis of residue samples taken from witness plates and soils collected following the controlled detonation of a series of different inorganic homemade explosives. The results obtained were also confirmed by parallel analysis of the same samples by capillary electrophoresis (CE) with excellent agreement being obtained.

Mixed-Mode Bending Method for Delamination Testing

NASA Technical Reports Server (NTRS)

Reeder, James R.; Crews, John R., Jr.

1990-01-01

A mixed mode delamination test procedure was developed combining double cantilever beam (DCB) mode I loading and end-notch fixture (ENF) mode II loading on a split unidirectional laminate. By loading with a lever, a single applied load simultaneously produces mode I and mode II bending loads on the specimen. This mixed-mode bending (MMB) test was analyzed using both finite-element procedures and beam theory to calculate the mode I and mode II components of strain-energy release rate G(sub I) and G(sub II), respectively. A wide range of G(sub I)/G(sub II) ratios can be produced by varying the load position on the lever. As the delamination extended, the G(sub I)/G(sub II) ratios varied by less than 5%. Beam theory equations agreed closely with the finite-element results and provide a basis for selection of G(sub I)/G(sub II) test ratios and a basis for computing the mode I and mode II components of measured delamination toughness. The MMB test was demonstrated using AS4/PEEK (APC2) unidirectional laminates. The MMB test introduced in this paper is rather simple and is believed to offer several advantages over most current mixed-mode test.

Anti-Carbonic Anhydrase II Antibodies in End-Stage Renal Disease Patients

PubMed Central

Alver, Ahmet; Menteşe, Ahmet; Menteşe, Ümit; Sümer, Ayşegül; Uçar, Fahri; Us Altay, Diler

2014-01-01

Objective The aim of this study was to investigate the presence of anti-carbonic anhydrase (CA II) autoantibodies in patients with end-stage renal disease (ESRD) and relationships between the autoantibody titers and ghrelin, glucose, blood urea nitrogen (BUN) and creatinine. Subjects and Methods Serum CA II autoantibody titers, malondialdehyde (MDA), BUN, creatinine and ghrelin levels were measured in 45 ESRD patients and 45 healthy subjects. Results The CA II autoantibody titers in the ESRD group (0.170 ± 0.237) were significantly higher than those in the control group (0.079 ± 0.032; p = 0.035). MDA and ghrelin levels were also significantly higher in the ESRD group (p < 0.001). A weak positive correlation was determined between anti-CA II antibody titers and MDA, and a negative correlation was observed between ghrelin levels and anti-CA II antibody titers (r = 0.287, p = 0.028 and r =b −0.278, p = 0.032, respectively). Conclusions In ESRD patients, the results showed the development of an autoimmune response against CA II. This suggests that anti-CA II antibodies could be involved in the pathogenesis of ESRD. PMID:24903210

Enrichment and separation of chlorogenic acid from the extract of Eupatorium adenophorum Spreng by macroporous resin.

PubMed

Liu, Boyan; Dong, Beitao; Yuan, Xiaofan; Kuang, Qirong; Zhao, Qingsheng; Yang, Mei; Liu, Jie; Zhao, Bing

2016-01-01

A simple and efficient chromatographic method for separation of chlorogenic acid from Eupatorium adenophorum Spreng extract was developed. The adsorption properties of nine macroporous resins were evaluated. NKA-II resin showed much better adsorption/desorption properties. The adsorption of chlorogenic acid on NKA-II resin at 25°C was well fitted to Langmuir isotherm model and pseudo-second-order kinetic model. The dynamic adsorption and desorption experiments were carried out on columns packed with NKA-II resin to optimize the separation process. The content of chlorogenic acid in the product increased to 22.17%, with a recovery yield of 82.41%. Copyright © 2015 Elsevier B.V. All rights reserved.

Mixed response and time-to-event endpoints for multistage single-arm phase II design.

PubMed

Lai, Xin; Zee, Benny Chung-Ying

2015-06-04

The objective of phase II cancer clinical trials is to determine if a treatment has sufficient activity to warrant further study. The efficiency of a conventional phase II trial design has been the object of considerable debate, particularly when the study regimen is characteristically cytostatic. At the time of development of a phase II cancer trial, we accumulated clinical experience regarding the time to progression (TTP) for similar classes of drugs and for standard therapy. By considering the time to event (TTE) in addition to the tumor response endpoint, a mixed-endpoint phase II design may increase the efficiency and ability of selecting promising cytotoxic and cytostatic agents for further development. We proposed a single-arm phase II trial design by extending the Zee multinomial method to fully use mixed endpoints with tumor response and the TTE. In this design, the dependence between the probability of response and the TTE outcome is modeled through a Gaussian copula. Given the type I and type II errors and the hypothesis as defined by the response rate (RR) and median TTE, such as median TTP, the decision rules for a two-stage phase II trial design can be generated. We demonstrated through simulation that the proposed design has a smaller expected sample size and higher early stopping probability under the null hypothesis than designs based on a single-response endpoint or a single TTE endpoint. The proposed design is more efficient for screening new cytotoxic or cytostatic agents and less likely to miss an effective agent than the alternative single-arm design.

A prediction model of drug-induced ototoxicity developed by an optimal support vector machine (SVM) method.

PubMed

Zhou, Shu; Li, Guo-Bo; Huang, Lu-Yi; Xie, Huan-Zhang; Zhao, Ying-Lan; Chen, Yu-Zong; Li, Lin-Li; Yang, Sheng-Yong

2014-08-01

Drug-induced ototoxicity, as a toxic side effect, is an important issue needed to be considered in drug discovery. Nevertheless, current experimental methods used to evaluate drug-induced ototoxicity are often time-consuming and expensive, indicating that they are not suitable for a large-scale evaluation of drug-induced ototoxicity in the early stage of drug discovery. We thus, in this investigation, established an effective computational prediction model of drug-induced ototoxicity using an optimal support vector machine (SVM) method, GA-CG-SVM. Three GA-CG-SVM models were developed based on three training sets containing agents bearing different risk levels of drug-induced ototoxicity. For comparison, models based on naïve Bayesian (NB) and recursive partitioning (RP) methods were also used on the same training sets. Among all the prediction models, the GA-CG-SVM model II showed the best performance, which offered prediction accuracies of 85.33% and 83.05% for two independent test sets, respectively. Overall, the good performance of the GA-CG-SVM model II indicates that it could be used for the prediction of drug-induced ototoxicity in the early stage of drug discovery. Copyright © 2014 Elsevier Ltd. All rights reserved.

Analysis for nickel (3 and 4) in positive plates from nickel-cadmium cells

NASA Technical Reports Server (NTRS)

Lewis, Harlan L.

1994-01-01

The NASA-Goddard procedure for destructive physical analysis (DPA) of nickel-cadmium cells contains a method for analysis of residual charged nickel as NiOOH in the positive plates at complete cell discharge, also known as nickel precharge. In the method, the Ni(III) is treated with an excess of an Fe(II) reducing agent and then back titrated with permanganate. The Ni(III) content is the difference between Fe(II) equivalents and permanganate equivalents. Problems have arisen in analysis at NAVSURFWARCENDIV, Crane because for many types of cells, particularly AA-size and some 'space-qualified' cells, zero or negative Ni(III) contents are recorded for which the manufacturer claims 3-5 percent precharge. Our approach to this problem was to reexamine the procedure for the source of error, and correct it or develop an alternative method.

Robust Requirements Tracing via Internet Search Technology: Improving an IV and V Technique. Phase 2

NASA Technical Reports Server (NTRS)

Hayes, Jane; Dekhtyar, Alex

2004-01-01

There are three major objectives to this phase of the work. (1) Improvement of Information Retrieval (IR) methods for Independent Verification and Validation (IV&V) requirements tracing. Information Retrieval methods are typically developed for very large (order of millions - tens of millions and more documents) document collections and therefore, most successfully used methods somewhat sacrifice precision and recall in order to achieve efficiency. At the same time typical IR systems treat all user queries as independent of each other and assume that relevance of documents to queries is subjective for each user. The IV&V requirements tracing problem has a much smaller data set to operate on, even for large software development projects; the set of queries is predetermined by the high-level specification document and individual requirements considered as query input to IR methods are not necessarily independent from each other. Namely, knowledge about the links for one requirement may be helpful in determining the links of another requirement. Finally, while the final decision on the exact form of the traceability matrix still belongs to the IV&V analyst, his/her decisions are much less arbitrary than those of an Internet search engine user. All this suggests that the information available to us in the framework of the IV&V tracing problem can be successfully leveraged to enhance standard IR techniques, which in turn would lead to increased recall and precision. We developed several new methods during Phase II; (2) IV&V requirements tracing IR toolkit. Based on the methods developed in Phase I and their improvements developed in Phase II, we built a toolkit of IR methods for IV&V requirements tracing. The toolkit has been integrated, at the data level, with SAIC's SuperTracePlus (STP) tool; (3) Toolkit testing. We tested the methods included in the IV&V requirements tracing IR toolkit on a number of projects.

A sensitive, selective and rapid determination of lead(II) ions in real-life samples using an electrochemically reduced graphene oxide-graphite reinforced carbon electrode.

PubMed

Hamsawahini, Kunashegaran; Sathishkumar, Palanivel; Ahamad, Rahmalan; Yusoff, Abdull Rahim Mohd

2015-11-01

In this study, a sensitive and cost-effective electrochemically reduced graphene oxide (ErGO) on graphite reinforced carbon (GRC) was developed for the detection of lead (Pb(II)) ions present in the real-life samples. A film of graphene oxide (GO) was drop-casted on GRC and their electrochemical properties were investigated using cyclic voltammetry (CV), amperometry and square wave voltammetry (SWV). Factors influencing the detection of Pb(II) ions, such as grades of GRC, constant applied cathodic potential (CACP), concentration of hydrochloric acid and drop-casting drying time were optimised. GO is irreversibly reduced in the range of -0.7 V to -1.6 V vs Ag/AgCl (3 M) in acidic condition. The results showed that the reduction behaviour of GO contributed to the high sensitivity of Pb(II) ions detection even at nanomolar level. The ErGO-GRC showed the detection limit of 0.5 nM and linear range of 3-15 nM in HCl (1 M). The developed electrode has potential to be a good candidate for the determination of Pb(II) ions in different aqueous system. The proposed method gives a good recovery rate of Pb(II) ions in real-life water samples such as tap water and river water. Copyright © 2015 Elsevier B.V. All rights reserved.

Software Reviews: Programs Worth a Second Look.

ERIC Educational Resources Information Center

Classroom Computer Learning, 1989

1989-01-01

Reviews three software programs: (1) "Cartooners"--develops creative arts and animation, grades 1-6, Apple IIGS; (2) "PC Globe+"--social studies, geography, grades 4-12, IBM(384K); (3) "Wood Car Rally"--physical science, scientific method, grades 3-9, Apple II. (MVL)

Investigation into improved pavement curing materials and techniques : part 1 (phases I and II).

DOT National Transportation Integrated Search

2002-04-01

Concrete curing is closely related to cement hydration, microstructure development, and concrete : performance. Application of a liquid membrane-forming curing compound is among the most widely : used curing methods for concrete pavements and bridge ...

AAS and spectrophotometric methods for the determination metoprolol tartrate in tablets

NASA Astrophysics Data System (ADS)

Alpdoğan, Güzin; Sungur, Sidika

1999-11-01

Sensitive and specific atomic adsorption spectroscopy (AAS) and spectrophotometric methods have been developed for the determination of beta adrenergic blocking drug, metoprolol tartrate.The method is based on the formation of Cu(II) dithiocarbamate complex by derivatization of the secondary amino group of metoprolol with CS 2 and CuCl 2 in the presence of ammonia.The copper-bis(dithiocarbamate) complex was extracted into chloroform and the concentration of metoprolol tartrate was determined directly by spectrophotometric and indirectly by AAS measurement of copper.The two methods developed were applied to the assay of metoprolol tartrate in commercial tablet formulations.The methods were compared statistically with each other and with the high performance liquid chromatography (HPLC) method of USPXXII using t- and F-tests.

Research progress in Asia on methods of processing laser-induced breakdown spectroscopy data

NASA Astrophysics Data System (ADS)

Guo, Yang-Min; Guo, Lian-Bo; Li, Jia-Ming; Liu, Hong-Di; Zhu, Zhi-Hao; Li, Xiang-You; Lu, Yong-Feng; Zeng, Xiao-Yan

2016-10-01

Laser-induced breakdown spectroscopy (LIBS) has attracted much attention in terms of both scientific research and industrial application. An important branch of LIBS research in Asia, the development of data processing methods for LIBS, is reviewed. First, the basic principle of LIBS and the characteristics of spectral data are briefly introduced. Next, two aspects of research on and problems with data processing methods are described: i) the basic principles of data preprocessing methods are elaborated in detail on the basis of the characteristics of spectral data; ii) the performance of data analysis methods in qualitative and quantitative analysis of LIBS is described. Finally, a direction for future development of data processing methods for LIBS is also proposed.

Development and validation of a UPLC-MS/MS method for simultaneous determination of fotagliptin and its two major metabolites in human plasma and urine.

PubMed

Wang, Zhenlei; Jiang, Ji; Hu, Pei; Zhao, Qian

2017-02-01

Fotagliptin is a novel dipeptidyl peptidase IV inhibitor under clinical development for the treatment of Type II diabetes mellitus. The objective of this study was to develop and validate a specific and sensitive ultra-performance liquid chromatography (UPLC)-MS/MS method for simultaneous determination of fotagliptin and its two major metabolites in human plasma and urine. Methodology & results: After being pretreated using an automatized procedure, the plasma and urine samples were separated and detected using a UPLC-ESI-MS/MS method, which was validated following the international guidelines. A selective and sensitive UPLC-MS/MS method was first developed and validated for quantifying fotagliptin and its metabolite in human plasma and urine. The method was successfully applied to support the clinical study of fotagliptin in Chinese healthy subjects.

A comparison of numerical solutions of partial differential equations with probabilistic and possibilistic parameters for the quantification of uncertainty in subsurface solute transport.

PubMed

Zhang, Kejiang; Achari, Gopal; Li, Hua

2009-11-03

Traditionally, uncertainty in parameters are represented as probabilistic distributions and incorporated into groundwater flow and contaminant transport models. With the advent of newer uncertainty theories, it is now understood that stochastic methods cannot properly represent non random uncertainties. In the groundwater flow and contaminant transport equations, uncertainty in some parameters may be random, whereas those of others may be non random. The objective of this paper is to develop a fuzzy-stochastic partial differential equation (FSPDE) model to simulate conditions where both random and non random uncertainties are involved in groundwater flow and solute transport. Three potential solution techniques namely, (a) transforming a probability distribution to a possibility distribution (Method I) then a FSPDE becomes a fuzzy partial differential equation (FPDE), (b) transforming a possibility distribution to a probability distribution (Method II) and then a FSPDE becomes a stochastic partial differential equation (SPDE), and (c) the combination of Monte Carlo methods and FPDE solution techniques (Method III) are proposed and compared. The effects of these three methods on the predictive results are investigated by using two case studies. The results show that the predictions obtained from Method II is a specific case of that got from Method I. When an exact probabilistic result is needed, Method II is suggested. As the loss or gain of information during a probability-possibility (or vice versa) transformation cannot be quantified, their influences on the predictive results is not known. Thus, Method III should probably be preferred for risk assessments.

An Analysis of a Finite Element Method for Convection-Diffusion Problems. Part II. A Posteriori Error Estimates and Adaptivity.

DTIC Science & Technology

1983-03-01

AN ANALYSIS OF A FINITE ELEMENT METHOD FOR CONVECTION- DIFFUSION PROBLEMS PART II: A POSTERIORI ERROR ESTIMATES AND ADAPTIVITY by W. G. Szymczak Y 6a...PERIOD COVERED AN ANALYSIS OF A FINITE ELEMENT METHOD FOR final life of the contract CONVECTION- DIFFUSION PROBLEM S. Part II: A POSTERIORI ERROR ...Element Method for Convection- Diffusion Problems. Part II: A Posteriori Error Estimates and Adaptivity W. G. Szvmczak and I. Babu~ka# Laboratory for

Diabetic retinopathy: retina-specific methods for maintenance of diabetic rodents and evaluation of vascular histopathology and molecular abnormalities

PubMed Central

Veenstra, Alexander; Liu, Haitao; Lee, Chieh Allen; Du, Yunpeng; Tang, Jie; Kern, Timothy S.

2015-01-01

Diabetic retinopathy is a major cause of visual impairment, which continues to increase in prevalence as more and more people develop diabetes. Despite the importance of vision, the retina is one of the smallest tissues in the body, and specialized techniques to study the retinopathy have been developed. This chapter will summarize several methods used to (i) induce diabetes, (ii) maintain the diabetic animals throughout the months required for the development of typical vascular histopathology, (iii) evaluate vascular histopathology of diabetic retinopathy, and (iv) quantitate abnormalities implicated in the development of the retinopathy. PMID:26331759

Visual Reading Method for Detection of Bacterial Tannase

PubMed Central

Osawa, R.; Walsh, T. P.

1993-01-01

Tannase activity of bacteria capable of degrading tannin-protein complexes was determined by a newly developed visual reading method. The method is based on two phenomena: (i) the ability of tannase to hydrolyze methyl gallate to release free gallic acid and (ii) the green to brown coloration of gallic acid after prolonged exposure to oxygen in an alkaline condition. The method has been successfully used to detect the presence of tannase in the cultures of bacteria capable of degrading tannin-protein complexes. PMID:16348918

Recovery of precious metals from space

NASA Technical Reports Server (NTRS)

Freiser, Henry

1991-01-01

The overall objective is to develop efficient and economical separation and recovery methods for the platinum group and other precious metals. The separation of Pd(II) from Pt(II), Ir(III), and Rh(III) with trioctylphosphine oxide (TOPO) in heptane using centrifugal partition chromatography (CPC) was investigated. Activities to achieve this objective focussed on selection and evaluation of extraction systems for the PGM and modification of selected systems for multistage operation with a view to scaling up to desired macro levels. On the basis of preliminary evaluation of a series of simple metal complexing agents and chelating agents, the TOPO in heptane was selected as a likely system for isolating of Pd(II) and Pt(II) from the other PGM. A multistage apparatus capable of configuration as a simple rugged device, a centrifugal partition chromatograph (CPC), was shown to be effective. The extraction of Pd(II) was studied by CPC and batch solvent extraction. The distribution ratios for Pd(II) determined by both methods agree well. In low HCl concentrations (less than 0.1 M), the extracted species was PdCl2.(TOPO)2, irrespective of the chloride concentration, while at acid concentrations above 0.1 M, the Pd was extracted as the ion pair, 2(TOPO.H+).(PdCl4)2-. Base line separation of Pd(II) and Pt(II) in CPC was obtained under a variety of chloride and HCl concentration. It was demonstrated that the efficiency of CPC for metal separation was limited by chemical kinetic factors rather than instrumental factors, strongly suggesting that dramatic improvements can be achieved by studying reaction kinetics of formation and dissociation of the extractable metal complex.

Thermostable group II intron reverse transcriptase fusion proteins and their use in cDNA synthesis and next-generation RNA sequencing.

PubMed

Mohr, Sabine; Ghanem, Eman; Smith, Whitney; Sheeter, Dennis; Qin, Yidan; King, Olga; Polioudakis, Damon; Iyer, Vishwanath R; Hunicke-Smith, Scott; Swamy, Sajani; Kuersten, Scott; Lambowitz, Alan M

2013-07-01

Mobile group II introns encode reverse transcriptases (RTs) that function in intron mobility ("retrohoming") by a process that requires reverse transcription of a highly structured, 2-2.5-kb intron RNA with high processivity and fidelity. Although the latter properties are potentially useful for applications in cDNA synthesis and next-generation RNA sequencing (RNA-seq), group II intron RTs have been difficult to purify free of the intron RNA, and their utility as research tools has not been investigated systematically. Here, we developed general methods for the high-level expression and purification of group II intron-encoded RTs as fusion proteins with a rigidly linked, noncleavable solubility tag, and we applied them to group II intron RTs from bacterial thermophiles. We thus obtained thermostable group II intron RT fusion proteins that have higher processivity, fidelity, and thermostability than retroviral RTs, synthesize cDNAs at temperatures up to 81°C, and have significant advantages for qRT-PCR, capillary electrophoresis for RNA-structure mapping, and next-generation RNA sequencing. Further, we find that group II intron RTs differ from the retroviral enzymes in template switching with minimal base-pairing to the 3' ends of new RNA templates, making it possible to efficiently and seamlessly link adaptors containing PCR-primer binding sites to cDNA ends without an RNA ligase step. This novel template-switching activity enables facile and less biased cloning of nonpolyadenylated RNAs, such as miRNAs or protein-bound RNA fragments. Our findings demonstrate novel biochemical activities and inherent advantages of group II intron RTs for research, biotechnological, and diagnostic methods, with potentially wide applications.

Assessing the performance of sewer rehabilitation on the reduction of infiltration and inflow.

PubMed

Staufer, P; Scheidegger, A; Rieckermann, J

2012-10-15

Inflow and Infiltration (I/I) into sewer systems is generally unwanted, because, among other things, it decreases the performance of wastewater treatment plants and increases combined sewage overflows. As sewer rehabilitation to reduce I/I is very expensive, water managers not only need methods to accurately measure I/I, but also they need sound approaches to assess the actual performance of implemented rehabilitation measures. However, such performance assessment is rarely performed. On the one hand, it is challenging to adequately take into account the variability of influential factors, such as hydro-meteorological conditions. On the other hand, it is currently not clear how experimental data can indeed support robust evidence for reduced I/I. In this paper, we therefore statistically assess the performance of rehabilitation measures to reduce I/I. This is possible by using observations in a suitable reference catchment as a control group and assessing the significance of the observed effect by regression analysis, which is well established in other disciplines. We successfully demonstrate the usefulness of the approach in a case study, where rehabilitation reduced groundwater infiltration by 23.9%. A reduction of stormwater inflow of 35.7%, however, was not statistically significant. Investigations into the experimental design of monitoring campaigns confirmed that the variability of the data as well as the number of observations collected before the rehabilitation impact the detection limit of the effect. This implies that it is difficult to improve the data quality after the rehabilitation has been implemented. Therefore, future practical applications should consider a careful experimental design. Further developments could employ more sophisticated monitoring methods, such as stable environmental isotopes, to directly observe the individual infiltration components. In addition, water managers should develop strategies to effectively communicate statistically not significant I/I reduction ratios to decision makers. Copyright © 2012 Elsevier Ltd. All rights reserved.

20 CFR 404.527 - Additional methods for recovery of title II benefit overpayments.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Additional methods for recovery of title II... or Recovery of Overpayments, and Liability of a Certifying Officer § 404.527 Additional methods for recovery of title II benefit overpayments. (a) General. In addition to the methods specified in §§ 404.502...

20 CFR 404.527 - Additional methods for recovery of title II benefit overpayments.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 20 Employees' Benefits 2 2011-04-01 2011-04-01 false Additional methods for recovery of title II... or Recovery of Overpayments, and Liability of a Certifying Officer § 404.527 Additional methods for recovery of title II benefit overpayments. (a) General. In addition to the methods specified in §§ 404.502...

20 CFR 404.527 - Additional methods for recovery of title II benefit overpayments.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 20 Employees' Benefits 2 2014-04-01 2014-04-01 false Additional methods for recovery of title II... or Recovery of Overpayments, and Liability of a Certifying Officer § 404.527 Additional methods for recovery of title II benefit overpayments. (a) General. In addition to the methods specified in §§ 404.502...

20 CFR 404.527 - Additional methods for recovery of title II benefit overpayments.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 20 Employees' Benefits 2 2013-04-01 2013-04-01 false Additional methods for recovery of title II... or Recovery of Overpayments, and Liability of a Certifying Officer § 404.527 Additional methods for recovery of title II benefit overpayments. (a) General. In addition to the methods specified in §§ 404.502...

20 CFR 404.527 - Additional methods for recovery of title II benefit overpayments.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 20 Employees' Benefits 2 2012-04-01 2012-04-01 false Additional methods for recovery of title II... or Recovery of Overpayments, and Liability of a Certifying Officer § 404.527 Additional methods for recovery of title II benefit overpayments. (a) General. In addition to the methods specified in §§ 404.502...

Analysis of chemical warfare agents. II. Use of thiols and statistical experimental design for the trace level determination of vesicant compounds in air samples.

PubMed

Muir, Bob; Quick, Suzanne; Slater, Ben J; Cooper, David B; Moran, Mary C; Timperley, Christopher M; Carrick, Wendy A; Burnell, Christopher K

2005-03-18

Thermal desorption with gas chromatography-mass spectrometry (TD-GC-MS) remains the technique of choice for analysis of trace concentrations of analytes in air samples. This paper describes the development and application of a method for analysing the vesicant compounds sulfur mustard and Lewisites I-III. 3,4-Dimercaptotoluene and butanethiol were used to spike sorbent tubes and vesicant vapours sampled; Lewisite I and II reacted with the thiols while sulfur mustard and Lewisite III did not. Statistical experimental design was used to optimise thermal desorption parameters and the optimum method used to determine vesicant compounds in headspace samples taken from a decontamination trial. 3,4-Dimercaptotoluene reacted with Lewisites I and II to give a common derivative with a limit of detection (LOD) of 260 microg m(-3), while the butanethiol gave distinct derivatives with limits of detection around 30 microg m(-3).

A fully automated and scalable timing probe-based method for time alignment of the LabPET II scanners

NASA Astrophysics Data System (ADS)

Samson, Arnaud; Thibaudeau, Christian; Bouchard, Jonathan; Gaudin, Émilie; Paulin, Caroline; Lecomte, Roger; Fontaine, Réjean

2018-05-01

A fully automated time alignment method based on a positron timing probe was developed to correct the channel-to-channel coincidence time dispersion of the LabPET II avalanche photodiode-based positron emission tomography (PET) scanners. The timing probe was designed to directly detect positrons and generate an absolute time reference. The probe-to-channel coincidences are recorded and processed using firmware embedded in the scanner hardware to compute the time differences between detector channels. The time corrections are then applied in real-time to each event in every channel during PET data acquisition to align all coincidence time spectra, thus enhancing the scanner time resolution. When applied to the mouse version of the LabPET II scanner, the calibration of 6 144 channels was performed in less than 15 min and showed a 47% improvement on the overall time resolution of the scanner, decreasing from 7 ns to 3.7 ns full width at half maximum (FWHM).

Detection and Recovery of Palladium, Gold and Cobalt Metals from the Urban Mine Using Novel Sensors/Adsorbents Designated with Nanoscale Wagon-wheel-shaped Pores.

PubMed

El-Safty, Sherif A; Shenashen, Mohamed A; Sakai, Masaru; Elshehy, Emad; Halada, Kohmei

2015-12-06

Developing low-cost, efficient processes for recovering and recycling palladium, gold and cobalt metals from urban mine remains a significant challenge in industrialized countries. Here, the development of optical mesosensors/adsorbents (MSAs) for efficient recognition and selective recovery of Pd(II), Au(III), and Co(II) from urban mine was achieved. A simple, general method for preparing MSAs based on using high-order mesoporous monolithic scaffolds was described. Hierarchical cubic Ia3d wagon-wheel-shaped MSAs were fabricated by anchoring chelating agents (colorants) into three-dimensional pores and micrometric particle surfaces of the mesoporous monolithic scaffolds. Findings show, for the first time, evidence of controlled optical recognition of Pd(II), Au(III), and Co(II) ions and a highly selective system for recovery of Pd(II) ions (up to ~95%) in ores and industrial wastes. Furthermore, the controlled assessment processes described herein involve evaluation of intrinsic properties (e.g., visual signal change, long-term stability, adsorption efficiency, extraordinary sensitivity, selectivity, and reusability); thus, expensive, sophisticated instruments are not required. Results show evidence that MSAs will attract worldwide attention as a promising technological means of recovering and recycling palladium, gold and cobalt metals.

Detection and Recovery of Palladium, Gold and Cobalt Metals from the Urban Mine Using Novel Sensors/Adsorbents Designated with Nanoscale Wagon-wheel-shaped Pores

PubMed Central

El-Safty, Sherif A.; Shenashen, Mohamed A.; Sakai, Masaru; Elshehy, Emad; Halada, Kohmei

2015-01-01

Developing low-cost, efficient processes for recovering and recycling palladium, gold and cobalt metals from urban mine remains a significant challenge in industrialized countries. Here, the development of optical mesosensors/adsorbents (MSAs) for efficient recognition and selective recovery of Pd(II), Au(III), and Co(II) from urban mine was achieved. A simple, general method for preparing MSAs based on using high-order mesoporous monolithic scaffolds was described. Hierarchical cubic Ia3d wagon-wheel-shaped MSAs were fabricated by anchoring chelating agents (colorants) into three-dimensional pores and micrometric particle surfaces of the mesoporous monolithic scaffolds. Findings show, for the first time, evidence of controlled optical recognition of Pd(II), Au(III), and Co(II) ions and a highly selective system for recovery of Pd(II) ions (up to ~95%) in ores and industrial wastes. Furthermore, the controlled assessment processes described herein involve evaluation of intrinsic properties (e.g., visual signal change, long-term stability, adsorption efficiency, extraordinary sensitivity, selectivity, and reusability); thus, expensive, sophisticated instruments are not required. Results show evidence that MSAs will attract worldwide attention as a promising technological means of recovering and recycling palladium, gold and cobaltmetals. PMID:26709467

Rhodium(II) metallopeptide catalyst design enables fine control in selective functionalization of natural SH3 domains.

PubMed

Vohidov, Farrukh; Coughlin, Jane M; Ball, Zachary T

2015-04-07

Chemically modified proteins are increasingly important for use in fundamental biophysical studies, chemical biology, therapeutic protein development, and biomaterials. However, chemical methods typically produce heterogeneous labeling and cannot approach the exquisite selectivity of enzymatic reactions. While bioengineered methods are sometimes an option, selective reactions of natural proteins remain an unsolved problem. Here we show that rhodium(II) metallopeptides combine molecular recognition with promiscuous catalytic activity to allow covalent decoration of natural SH3 domains, depending on choice of catalyst but independent of the specific residue present. A metallopeptide catalyst succeeds in modifying a single SH3-containing kinase at endogenous concentrations in prostate cancer (PC-3) cell lysate. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A Comparison of a Machine Learning Model with EuroSCORE II in Predicting Mortality after Elective Cardiac Surgery: A Decision Curve Analysis

PubMed Central

Allyn, Jérôme; Allou, Nicolas; Augustin, Pascal; Philip, Ivan; Martinet, Olivier; Belghiti, Myriem; Provenchere, Sophie; Montravers, Philippe; Ferdynus, Cyril

2017-01-01

Background The benefits of cardiac surgery are sometimes difficult to predict and the decision to operate on a given individual is complex. Machine Learning and Decision Curve Analysis (DCA) are recent methods developed to create and evaluate prediction models. Methods and finding We conducted a retrospective cohort study using a prospective collected database from December 2005 to December 2012, from a cardiac surgical center at University Hospital. The different models of prediction of mortality in-hospital after elective cardiac surgery, including EuroSCORE II, a logistic regression model and a machine learning model, were compared by ROC and DCA. Of the 6,520 patients having elective cardiac surgery with cardiopulmonary bypass, 6.3% died. Mean age was 63.4 years old (standard deviation 14.4), and mean EuroSCORE II was 3.7 (4.8) %. The area under ROC curve (IC95%) for the machine learning model (0.795 (0.755–0.834)) was significantly higher than EuroSCORE II or the logistic regression model (respectively, 0.737 (0.691–0.783) and 0.742 (0.698–0.785), p < 0.0001). Decision Curve Analysis showed that the machine learning model, in this monocentric study, has a greater benefit whatever the probability threshold. Conclusions According to ROC and DCA, machine learning model is more accurate in predicting mortality after elective cardiac surgery than EuroSCORE II. These results confirm the use of machine learning methods in the field of medical prediction. PMID:28060903

Synthesis of tin (II) oxide from tin (II) oxohydroxide

NASA Astrophysics Data System (ADS)

Kuznetsova, Svetlana; Lisitsa, Konstantin

2017-11-01

Sufficiently limited use of tin (II) oxide is associated with the difficulties of its preparation without impurities of tin (IV) oxide. Understanding the cause of the oxidation process will make it possible to develop methods for obtaining SnO without impurities. The influence of ammonium chloride concentration in the suspension on the oxide composition was investigated. The temperature of oxidation (400 °C) on the air and temperature decomposition in the argon (350 °C) of Sn6O4(OH)4 in the solid phase were determined by the thermal analysis method. The decomposition temperature of the oxyhydroxide in the suspension of ammonium chloride does not exceed 100 °C. An increase in the content of ammonium chloride in an aqueous solution leads to an increase i n the solubility of oxohydroxide and leads to an increase in pH. The suspensions of Sn6O4(OH)4 were subjected to heat treatment on a sand bath and under microwave irradiation. Samples of tin oxide were obtained. The quantitative composition of the mixture of tin oxides was determined. The research also highlights emphasizes that the oxidation of tin (II) to tin (IV) is associated with the dissolved oxygen content in the suspension.

Molecular detection of genotype II grass carp reovirus based on nucleic acid sequence-based amplification combined with enzyme-linked immunosorbent assay (NASBA-ELISA).

PubMed

Zeng, Weiwei; Yao, Wei; Wang, Yingying; Li, Yingying; Bermann, Sven M; Ren, Yan; Shi, Cunbin; Song, Xinjian; Huang, Qiwen; Zheng, Shuchen; Wang, Qing

2017-05-01

Grass carp reovirus (GCRV) is the causative agent of the grass carp hemorrhagic disease that has resulted in severe economic losses in the grass carp (Ctenopharyngodon idella) farming industry in China. Early diagnosis and vaccine administration are important priorities for GCRV control. In this study, a nucleic acid sequence-based amplification with enzyme-linked immunosorbent assay (NASBA-ELISA) was developed for to detect genotype II GCRV (GCRV- II). Primers specifically targeting viral RNA genome segment 6 were utilized for amplification in an isothermal digoxigenin-labeling NASBA process, resulting in DIG-labeled RNA amplicons. The amplicons were hybridized to specific biotinylated DNA probes and the products were detected colorimetrically using horseradish peroxidase and a microplate reader. The new method is able to detect GCRV at 14 copies/μL within 5h and had a diagnostic sensitivity and a specificity of 100% when GCRV-II and non-target virus were tested. This NASBA-ELISA was evaluated using a panel of clinical samples (n=103) to demonstrate that it is a rapid, effective and sensitive method for GCRV detection in grass carp aquaculture. Copyright © 2017 Elsevier B.V. All rights reserved.

Simultaneous Spectrophotometric Estimation of Nitazoxanide and Ofloxacin in Tablets

PubMed Central

Game, Madhuri D.; Sakarkar, D. M.

2011-01-01

Two simple, accurate and precise spectrophotometric methods have been developed for simultaneous determination of nitazoxanide and ofloxacin in tablets. Method I is Q-absorbance ratio method which involves Q-absorbance at isobestic point (306.25 nm) and max (347.5 nm) of nitazoxanide, while method II is two wavelength method, where 244.6 nm and 273.0 nm were selected as 1 and 2 for determination of nitazoxanide and 294.3 nm and 388.1 nm were selected as 3 and 4 for determination of ofloxacin. Both drugs obeyed the Beer's law in the concentration range 2-30 μg/ml,correlation coefficient (r2<1). Both methods were validated statistically and recovery studies were carried out to confirm the accuracy. Commercial tablet formulation was successfully analyzed using the developed methods. PMID:22131624

Prediction of antisymmetric buffet loads on horizontal stabilizers in massively separated flows, phase II

DOT National Transportation Integrated Search

1999-05-01

The Federal Aviation Administration (FAA) has a continuing program to collect data and develop predictive methods for aircraft flight loads. Some of the most severe and potentially catastrophic flight loads are produced by separated flows. Structural...

Canadian Contraception Consensus (Part 1 of 4).

PubMed

Black, Amanda; Guilbert, Edith; Costescu, Dustin; Dunn, Sheila; Fisher, William; Kives, Sari; Mirosh, Melissa; Norman, Wendy V; Pymar, Helen; Reid, Robert; Roy, Geneviève; Varto, Hannah; Waddington, Ashley; Wagner, Marie-Soleil; Whelan, Anne Marie; Ferguson, Carrie; Fortin, Claude; Kielly, Maria; Mansouri, Shireen; Todd, Nicole

2015-10-01

To provide guidelines for health care providers on the use of contraceptive methods to prevent pregnancy and on the promotion of healthy sexuality. Guidance for Canadian practitioners on overall effectiveness, mechanism of action, indications, contraindications, non-contraceptive benefits, side effects and risks, and initiation of cited contraceptive methods; family planning in the context of sexual health and general well-being; contraceptive counselling methods; and access to, and availability of, cited contraceptive methods in Canada. Published literature was retrieved through searches of Medline and The Cochrane Database from January 1994 to January 2015 using appropriate controlled vocabulary (e.g., contraception, sexuality, sexual health) and key words (e.g., contraception, family planning, hormonal contraception, emergency contraception). Results were restricted to systematic reviews, randomized control trials/controlled clinical trials, and observational studies published in English from January 1994 to January 2015. Searches were updated on a regular basis and incorporated in the guideline to June 2015. Grey (unpublished) literature was identified through searching the websites of health technology assessment and health technology-related agencies, clinical practice guideline collections, clinical trial registries, and national and international medical specialty societies. The quality of the evidence in this document was rated using the criteria described in the Report of the Canadian Task Force on Preventive Health Care (Table). Chapter 1: Contraception in Canada Summary Statements 1. Canadian women spend a significant portion of their lives at risk of an unintended pregnancy. (II-2) 2. Effective contraceptive methods are underutilized in Canada, particularly among vulnerable populations. (II-2) 3. Long-acting reversible contraceptive methods, including contraceptive implants and intrauterine contraception (copper-releasing and levonorgestrel-releasing devices/systems), are the most effective reversible contraceptive methods and have the highest continuation rates. (II-1) 4. Canada currently does not collect reliable data to determine the use of contraceptive methods, abortion rates, and the prevalence of unintended pregnancy among reproductive-age women. (II-2) 5. A universal subsidy for contraceptive methods as provided by many of Canada's peer nations and a few Canadian provinces may produce health system cost-savings. (II-2) 6. Health Canada approval processes for contraceptives have been less efficient than those of other drug approval agencies and Health Canada processes for other classes of pharmaceuticals. (II-2) 7. It is feasible and safe for contraceptives and family planning services to be provided by appropriately trained allied health professionals such as midwives, registered nurses, nurse practitioners, and pharmacists. (II-2) Recommendations 1. Contraceptive counselling should include a discussion of typical use failure rates and the importance of using the contraceptive method consistently and correctly in order to avoid pregnancy. (II-2A) 2. Women seeking contraception should be counselled on the wide range of effective methods of contraception available, including long-acting reversible contraceptive methods (LARCs). LARCs are the most effective methods of reversible contraception, have high continuation rates, and should be considered when presenting contraceptive options to any woman of reproductive age. (II-2A) 3. Family planning counselling should include counselling on the decline of fertility associated with increasing female age. (III-A) 4. Health policy supporting a universal contraception subsidy and strategies to promote the uptake of highly effective methods as cost-saving measures that improve health and health equity should be considered by Canadian health decision makers. (III-B) 5. Canadian health jurisdictions should consider expanding the scope of practice of other trained professionals such as nurses, nurse practitioners, midwives, and pharmacists and promoting task-sharing in family planning. (II-2B) 6. The Canadian Community Health Survey should include adequate reproductive health indicators in order for health care providers and policy makers to make appropriate decisions regarding reproductive health policies and services in Canada. (III-B) 7. Health Canada processes and policies should be reviewed to ensure a wide range of modern contraceptive methods are available to Canadian women. (III-B) Chapter 2: Contraceptive Care and Access Summary Statements 8. Although there are many contraceptive options in Canada, only a narrow range of contraceptive methods are commonly used by those of reproductive age. (II-3) 9. Condom use decreases with longer relationship tenure and when the sexual partner is considered to be the main partner, likely due to a lower perceived risk of sexually transmitted infection in that relationship. Condom use may also decrease markedly as an unintended consequence when an effective non-barrier method, such as hormonal contraception or intrauterine contraception, is initiated. (II-3) 10. Family planning counselling provides a natural segue into screening for concerns about sexual function or intimate partner violence. (III) 11. Well-informed and well-motivated individuals who have developed skills to practise safer sex behaviours are more likely to use contraceptive and safer sex methods effectively and consistently. (II-2) Recommendations 8. Comprehensive family planning services, including abortion services, should be accessible to all Canadians regardless of geographic location. These services should be confidential, non-judgemental, and respectful of individuals' privacy and cultural contexts. (III-A) 9. A contraceptive visit should include history taking, screening for contraindications, dispensing or prescribing a method of contraception, and exploring contraceptive choice and adherence in the broader context of the individual's sexual behaviour, reproductive health risk, social circumstances, and relevant belief systems. (III-B) 10. Health care providers should provide practical information on the wide range of contraceptive options and their potential non-contraceptive benefits and assist women and their partners in determining the best user-method fit. (III-B) 11. Health care providers should assist women and men in developing the skills necessary to negotiate the use of contraception and the correct and consistent use of a chosen method. (III-B) 12. Contraceptive care should include discussion and management of the risk of sexually transmitted infection, including appropriate recommendations for condom use and dual protection, STI screening, post-exposure prophylaxis, and Hepatitis B and human papillomavirus vaccination. (III-B) 13. Health care providers should emphasize the use of condoms not only for protection against sexually transmitted infection, but also as a back-up method when adherence to a hormonal contraceptive may be suboptimal. (I-A) 14. Health care providers should be aware of current media controversies in reproductive health and acquire relevant evidence-based information that can be briefly and directly communicated to their patients. (III-B) 15. Referral resources for intimate partner violence, sexually transmitted infections, sexual dysfunction, induced abortion services, and child protection services should be available to help clinicians provide contraceptive care in the broader context of women's health. (III-B) Chapter 3: Emergency Contraception Summary Statements 12. The copper intrauterine device is the most effective method of emergency contraception. (II-2) 13. A copper intrauterine device can be used for emergency contraception up to 7 days after unprotected intercourse provided that pregnancy has been ruled out and there are no other contraindications to its insertion. (II-2) 14. Levonorgestrel emergency contraception is effective up to 5 days (120 hours) after intercourse; its effectiveness decreases as the time between unprotected intercourse and ingestion increases. (II-2) 15. Ulipristal acetate for emergency contraception is more effective than levonorgestrel emergency contraception up to 5 days after unprotected intercourse. This difference in effectiveness is more pronounced as the time from unprotected intercourse increases, especially after 72 hours. (I) 16. Hormonal emergency contraception (levonorgestrel emergency contraception and ulipristal acetate for emergency contraception) is not effective if taken on the day of ovulation or after ovulation. (II-2) 17. Levonorgestrel emergency contraception may be less effective in women with a body mass index > 25 kg/m2 and ulipristal acetate for emergency contraception may be less effective in women with a body mass index > 35 kg/m2. However, hormonal emergency contraception may still retain some effectiveness regardless of a woman's body weight or body mass index. (II-2) 18. Hormonal emergency contraception is associated with higher failure rates when women continue to have subsequent unprotected intercourse. (II-2) 19. Hormonal contraception can be initiated the day of or the day following the use of levonorgestrel emergency contraception, with back-up contraception used for the first 7 days. (III) 20. Hormonal contraception can be initiated 5 days following the use of ulipristal acetate for emergency contraception, with back-up contraception used for the first 14 days. (III) Recommendations 16. All emergency contraception should be initiated as soon as possible after unprotected intercourse. (II-2A) 17. Women should be informed that the copper intrauterine device (IUD) is the most effective method of emergency contraception and can be used by any woman with no contraindications to IUD use. (II-3A) 18.

Characterization and biological activities of a novel polysaccharide isolated from raspberry (Rubus idaeus L.) fruits.

PubMed

Yu, Zeyuan; Liu, Lu; Xu, Yaqin; Wang, Libo; Teng, Xin; Li, Xingguo; Dai, Jing

2015-11-05

A water-soluble polysaccharide namely RCP-II from raspberry fruits was obtained by complex enzyme method followed by successive purification using macroporous resin D4020 and Sephadex G-100 columns. RCP-II was an acidic heteropolysaccharide and the characteristic structure of polysaccharide was determined. The carbohydrate of RCP-II was composed with galacturonic acid, rhamnose, arabinose, xylose, glucose and galactose in a molar ratio of 1.00:0.55:1.19:0.52:0.44:1.90 and the average molecular weight was estimated to be 4013 Da, based on dextran standards. RCP-II presented high scavenging activity toward DPPH•, HO•, O2(•-) in a concentration-dependent manner. The determination of the inhibitory activity on protein glycation showed that in 14 days of incubation the inhibitory ability of RCP-II was more effective on the development of non-enzymatic glycation reaction at early phase than that at the following two phases. Copyright © 2015 Elsevier Ltd. All rights reserved.

Phase I/II adaptive design for drug combination oncology trials

PubMed Central

Wages, Nolan A.; Conaway, Mark R.

2014-01-01

Existing statistical methodology on dose finding for combination chemotherapies has focused on toxicity considerations alone in finding a maximum tolerated dose combination to recommend for further testing of efficacy in a phase II setting. Recently, there has been increasing interest in integrating phase I and phase II trials in order to facilitate drug development. In this article, we propose a new adaptive phase I/II method for dual-agent combinations that takes into account both toxicity and efficacy after each cohort inclusion. The primary objective, both within and at the conclusion of the trial, becomes finding a single dose combination with an acceptable level of toxicity that maximizes efficacious response. We assume that there exist monotone dose–toxicity and dose–efficacy relationships among doses of one agent when the dose of other agent is fixed. We perform extensive simulation studies that demonstrate the operating characteristics of our proposed approach, and we compare simulated results to existing methodology in phase I/II design for combinations of agents. PMID:24470329

Virtex-II Pro SEE Test Methods and Results

NASA Technical Reports Server (NTRS)

Petrick, David; Powell, Wesley; Howard, James W., Jr.; LaBel, Kenneth A.

2004-01-01

The objective of this coarse Single Event Effect (SEE) test is to determine the suitability of the commercial Virtex-II Pro family for use in spaceflight applications. To this end, this test is primarily intended to determine any Singe Event Latchup (SEL) susceptibilities for these devices. Secondly, this test is intended to measure the level of Single Event Upset (SEU) susceptibilities and in a general sense where they occur. The coarse SEE test was performed on a commercial XC2VP7 device, a relatively small single processor version of the Virtex-II Pro. As the XC2VP7 shares the same functional block design and fabrication process with the larger Virtex-II Pro devices, the results of this test should also be applicable to the larger devices. The XC2VP7 device was tested on a commercial Virtex-II Pro development board. The testing was performed at the Cyclotron laboratories at Texas A&M and Michigan State Universities using ions of varying energy levels and fluences.

Rapid determination of crocins in saffron by near-infrared spectroscopy combined with chemometric techniques

NASA Astrophysics Data System (ADS)

Li, Shuailing; Shao, Qingsong; Lu, Zhonghua; Duan, Chengli; Yi, Haojun; Su, Liyang

2018-02-01

Saffron is an expensive spice. Its primary effective constituents are crocin I and II, and the contents of these compounds directly affect the quality and commercial value of saffron. In this study, near-infrared spectroscopy was combined with chemometric techniques for the determination of crocin I and II in saffron. Partial least squares regression models were built for the quantification of crocin I and II. By comparing different spectral ranges and spectral pretreatment methods (no pretreatment, vector normalization, subtract a straight line, multiplicative scatter correction, minimum-maximum normalization, eliminate the constant offset, first derivative, and second derivative), optimum models were developed. The root mean square error of cross-validation values of the best partial least squares models for crocin I and II were 1.40 and 0.30, respectively. The coefficients of determination for crocin I and II were 93.40 and 96.30, respectively. These results show that near-infrared spectroscopy can be combined with chemometric techniques to determine the contents of crocin I and II in saffron quickly and efficiently.

2,4-Dinitrophenylhydrazine functionalized sodium dodecyl sulfate-coated magnetite nanoparticles for effective removal of Cd(II) and Ni(II) ions from water samples.

PubMed

Sobhanardakani, Soheil; Zandipak, Raziyeh

2015-07-01

2,4-Dinitrophenylhydrazine immobilized on sodium dodecyl sulfate (SDS)-coated magnetite and was used for removal of Cd(II) and Ni(II) ions from aqueous solution. The prepared product was characterized by X-ray diffraction (XRD) analysis, Fourier transform infrared spectroscopy (FT-IR), and scanning electron microscopy (SEM). The size of the nanoparticles according to SEM was obtained around 20-35 nm. In batch tests, the effects of pH, contact time, initial metal concentration, and temperature were studied. The kinetic and equilibrium data were modeled with recently developed models. The adsorption kinetics and isotherms were well fitted by the fractal-like pseudo-second-order model and Langmuir-Freundlich model, respectively. Maximum adsorption capacity by this adsorbent is 255.1 mg g(-1) for Cd(II) ion and 319.6 mg g(-1) for Ni(II) ion at pH 7.0 and 25 °C. The method was successfully applied to the removal of metal cations in real samples (tap water, river water, and petrochemical wastewater).

Mercury(II) and methyl mercury determinations in water and fish samples by using solid phase extraction and cold vapour atomic absorption spectrometry combination.

PubMed

Tuzen, Mustafa; Karaman, Isa; Citak, Demirhan; Soylak, Mustafa

2009-07-01

A method has been developed for mercury(II) and methyl mercury speciation on Staphylococcus aureus loaded Dowex Optipore V-493 micro-column in the presented work, by using cold vapour atomic absorption spectrometry. Selective and sequential elution with 0.1 molL(-1) HCl for methyl mercury and 2 molL(-1) HCl for mercury(II) were performed at the pH range of 2-6. Optimal analytical conditions including pH, amounts of biosorbent, sample volumes were investigated. The detection limits of the analytes were 2.5 ngL(-1) for Hg(II) and 1.7 ngL(-1) for methyl mercury. The capacity of biosorbent for mercury(II) and methyl mercury was 6.5 and 5.4 mgg(-1), respectively. The validation of the presented procedure is performed by the analysis of standard reference material. The speciation procedure established was successfully applied to the speciation of mercury(II) and methyl mercury in natural water and microwave digested fish samples.

Ferrous iron phosphorus in sediments: development of a quantification method through 2,2'-bipyridine extraction.

PubMed

Li, Qingman; Wang, Xingxiang; Bartlett, Rebecca; Pinay, Gilles; Kan, Dan; Zhang, Wen; Sun, Jingxian

2012-11-01

The role of ferrous iron in the phosphorus cycle of an aquatic ecosystem is poorly understood because of a lack of suitable methods to quantitatively evaluate ferrous iron phosphorus (FIP) phases. Using sediments sampled from Fubao Bay of Dianchi Lake in China, a novel extraction method for FIP using 2,2'-bipyridine was explored. Total phosphorus and iron in the sediments ranged from 1.0 to 5.0 mg/g (dry weight) and 28.5 to 90.6 mg/g, respectively. Organic content (as indicated by loss on ignition or LOI) and iron(II) ranged from 3.1 to 27.0% and 26.5 to 64.9 mg/g, respectively. The dissolution dynamics of FIP extraction with a low solid/liquid ratio (1:25) indicated that a single application of 0.2% 2,2'-bipyridine extracted both iron(II) (Fe(II)) and phosphorus (as PO4(3-)) in sediments with different organic contents with low efficiency. The extraction efficiency of Fe(II) was improved by alteration of the solid/liquid ratio, but the effect was limited. However, addition of a 1:1000 solid/liquid ratio of 0.5 M potassium chloride to a 0.2% 2,2'-bipyridine solution significantly accelerated extraction of FIP with the release of Fe(II) and phosphorus toward equilibrium at approximately 150 hours. Further investigation demonstrated that 2,2'-bipyridine exhibited a higher selectivity in distinguishing FIP from phosphorus bound to ferric (Fe(III)) oxides or precipitated by calcium (Ca2+). Air-drying sediments significantly decreased the amount of extracted FIP, which indicates that fresh, wet sediment should be used in this type of FIP extraction. Based on experimental results using the proposed extraction protocol, (1) FIP in sediments of Fubao Bay had a predominant status in the lake sediment and accounted for 23.4 to 39.8% of total phosphorus, and (2) Fe(II)(FIP) released in the extraction is directly proportional to phosphorus(FIP) (Fe(II)(FIP) = 2.84 x P(FIP) + 0.0007; R2 = 0.97) with an average molar ratio of Fe(II)(FIP)/P(FIP) of 2.7. This study shows that FIP extraction with 2,2'-bipyridine is a robust method for releasing ferrous iron associated with phosphorus. Further, the high percentage of FIP in total phosphorus (40%) measured in the study site using this extraction method suggests that FIP might have been often underestimated in previous studies.

From World War to Woods Hole: The Use of Wartime Research Models for Curriculum Reform.

ERIC Educational Resources Information Center

Rudolph, John L.

2002-01-01

Considers the curriculum reform movement of the 1950s as an experiment in applying innovative research and development techniques perfected by scientists during World War II, tracing the development of newer methods of scientific analysis and examining how they were imported from military research to the field of education by a select group of…

Autogenous accelerated curing of concrete cylinders. Part V, ASTM Cooperative Testing Program with additional emphasis on the influence of container and storage characteristics (supplemented by data on water bath curing from an earlier council project).

DOT National Transportation Integrated Search

1971-01-01

Concomitant with the Research Council's studies of accelerated curing for strength testing, Subcommittee II-i of ASTM Committee C-9 was developing and refining accelerated methods for standardization. This development included a cooperative testing p...

A novel method for detection of apoptosis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zagariya, Alexander M., E-mail: zagariya@uic.edu

2012-04-15

There are two different Angiotensin II (ANG II) peptides in nature: Human type (ANG II) and Bovine type (ANG II*). These eight amino acid peptides differ only at position 5 where Valine is replaced by Isoleucine in the Bovine type. They are present in all species studied so far. These amino acids are different by only one atom of carbon. This difference is so small, that it will allow any of ANG II, Bovine or Human antibodies to interact with all species and create a universal method for apoptosis detection. ANG II concentrations are found at substantially higher levels inmore » apoptotic, compared to non-apoptotic, tissues. ANG II accumulation can lead to DNA damage, mutations, carcinogenesis and cell death. We demonstrate that Bovine antiserum can be used for universal detection of apoptosis. In 2010, the worldwide market for apoptosis detection reached the $20 billion mark and significantly increases each year. Most commercially available methods are related to Annexin V and TUNNEL. Our new method based on ANG II is more widely known to physicians and scientists compared to previously used methods. Our approach offers a novel alternative for assessing apoptosis activity with enhanced sensitivity, at a lower cost and ease of use.« less

Metal (II) Complexes Derived from Naphthofuran-2-carbohydrazide and Diacetylmonoxime Schiff Base: Synthesis, Spectroscopic, Electrochemical, and Biological Investigation

PubMed Central

Sumathi, R. B.; Halli, M. B.

2014-01-01

A new Schiff base and a new series of Co(II), Ni(II), Cu(II), Cd(II), and Hg(II) complexes were synthesized by the condensation of naphthofuran-2-carbohydrazide and diacetylmonoxime. Metal complexes of the Schiff base were prepared from their chloride salts of Co(II), Ni(II), Cu(II), Cd(II), and Hg(II) in ethanol. The ligand along with its metal complexes have been characterized on the basis of analytical data, IR, electronic, mass, 1HNMR, ESR spectral data, thermal studies, magnetic susceptibility, and molar conductance measurements. The nonelectrolytic behaviour of the complexes was assessed from the measured low conductance data. The elemental analysis of the complexes confirm the stoichiometry of the type CuL2Cl2 and MLCl2 where M = Ni(II), Co(II), Cd(II), and Hg(II) and L = Schiff base. The redox property of the Cu(II) complex was investigated by electrochemical method using cyclic voltammetry. In the light of these results, Co(II), Ni(II), and Cu(II) complexes are assigned octahedral geometry, Cd(II), and Hg(II) complexes tetrahedral geometry. In order to evaluate the effect of metal ions upon chelation, both the ligand and its metal complexes were screened for their antibacterial and antifungal activities by minimum inhibitory concentration (MIC) method. The DNA cleaving capacity of all the complexes was analysed by agarose gel electrophoresis method. PMID:24592203

Dexosomes as a therapeutic cancer vaccine: from bench to bedside.

PubMed

Le Pecq, Jean-Bernard

2005-01-01

Exosomes released from dendritic cells, now referred as dexosomes, have recently been extensively characterized. Preclinical studies in mice have shown that, when properly loaded with tumor antigens, dexosomes can elicit a strong antitumor activity. Before dexosomes could be used in humans as a therapeutic vaccine, extensive development work had to be performed to meet the present regulatory requirements. First a manufacturing process amenable to cGMP for isolating and purifying dexosomes was established. Methods for loading the Major Histocompatibility Complex (MHC) molecules class II and I in a quantitative and reproducible way were developed. The most challenging task was the establishment of a quality control method for accessing the biological activity of individual lots. Such a method must remain relatively simple and reflect the mechanism of action of dexosomes. This was accomplished by measuring the transfer of a MHC class II superantigen complex to an antigen presenting cell that was MHC class II negative. More than 100 separate dexosome lots were prepared from blood cells of healthy volunteers to evaluate the variability of the manufacturing process. The analysis of the data showed that the main source of variability was related to the heterogeneity of the human population and not to the manufacturing process. These studies allowed to perform two phase I clinical trials. A total of 24 cancer patients received Dex therapy. Dexosome production from cells of cancer patient was found equivalent to that of normal volunteer. No adverse events related to this therapy were reported. Evidence of dexosome bioactivity was observed.

Research Methods to Develop Measures of Effectiveness of the United States Coast Guard’s Vessel Inspection and Boarding Program. Executive Summary - Volume I

DTIC Science & Technology

1995-05-01

Service, Springfield, Virginia 22161 Prepared for: LJCý U.S. Coast Guard Research and Development Center 1082 Shennecossett Road < Groton, Connecticut...States Coast Guard Research & Development Center 1082 Shennecossett Road Groton, CT 06340-6096 ii Technical Report Documentation Paae 1. Report No. 2...U.S. Coast Guard 14. Sponsoring Agency Code Research and Development Center Office of Engineering, Logistics, 1082 Shennecossett Road and Development

Novel potentiometric application for the determination of pantoprazole sodium and itopride hydrochloride in their pure and combined dosage form.

PubMed

Ragab, Mona T; Abd El-Rahman, Mohamed K; Ramadan, Nesrin K; El-Ragehy, Nariman A; El-Zeany, Badr A

2015-06-01

Three sensitive and selective polyvinyl chloride (PVC) matrix membrane electrodes were developed and investigated. Sensor I was developed using tetraheptylammonium bromide (THB) as an anion exchanger with 2-nitrophenyl octyl ether (2-NPOE) as a plasticizer for the determination of the anionic drug pantoprazole sodium sesquihydrate (PAN). To determine the cationic drug itopride hydrochloride (ITH), two electrodes (sensors II and III) were developed using potassium tetrakis(4-chlorophenyl) borate (KTCPB) as a cation exchanger with dioctyl phthalate (DOP) as a plasticizer. Selective molecular recognition components, 2-hydroxypropyl-β-cyclodextrin (2-HP βCD) and 4-tert-butylcalix[8]arene (tBC8), were used as ionophores to improve the selectivity of sensors II and III, respectively. The proposed sensors had a linear dynamic range of 1×10(-5) to 1×10(-2) mol L(-1) with Nernstian slopes of -54.83±0.451, 56.90±0.300, and 51.03±1.909 mV/decade for sensors I, II and III, respectively. The Nernstian slopes were also estimated over the pH ranges of 11-13, 3.5-8 and 4-7 for the three sensors, respectively. The proposed sensors displayed useful analytical characteristics for the determination of PAN and ITH in bulk powder, in laboratory prepared mixtures and in combined dosage forms with clear discrimination from several ions, sugars and some common drug excipients. The method was validated according to ICH guidelines. Statistical comparison between the results from the proposed method and the results from the reference methods showed no significant difference regarding accuracy and precision. Copyright © 2015 Elsevier B.V. All rights reserved.

Volume II: Compendium Abstracts

DTIC Science & Technology

2008-08-01

project developed a fast and simple method of characterization for ceramic , polymer composite, and ceramic -composite materials systems. Current methods...incrementally at 1-inch intervals and displayed as a false-color image map of the sample. This experimental setup can be easily scaled from single ceramic ...low-power, high-force characteristics of lead zirconate titanate ( PZT ) and an offset-beam design to achieve rotational or near-linear translational

Paramagnetic resonance studies of bistrispyrazolylborate cobalt(II) and related derivatives

NASA Astrophysics Data System (ADS)

Myers, William K.

Herein, a systematic frozen solution electron-nuclear double resonance (ENDOR) study of high-spin Co(II) complexes is reported to demonstrate the efficacy of methyl substitutions as a means of separating dipolar and contact coupling, and further, to increase the utility of high-spin Co(II) as a spectroscopic probe for the ubiquitous, but spectroscopically-silent Zn(II) metalloenzymes. High-spin (hs) Co(II) has been subject of paramagnetic resonance studies for over 50 years and has been used as a spectroscopic probe for Zn metalloenzymes for over 35 years. However, as will be seen, the inherent complexity of the electronic properties of the cobaltous ion remains to be exploited to offer a wealth of information on Zn(II) enzymatic environments. Specifically, ENDOR measurements on bistrispyrazolylborate cobalt(II) confirm the utility of the novel method of methyl substitution to differentiate dipolar and Fermi contact couplings. An extensive set of electron paramagnetic resonance (EPR) simulations were performed. Software was developed to implement an ENDOR control interface. Finally, proton relaxation measurements were made in the range of 12-42 MHz, which were accounted for with the large g-value anisotropy of the Co(II) compounds. Taken as a whole, these studies point to the rich complexity of the electronic structure of high-spin cobalt(II) and, when sufficiently well-characterized, the great utility it has as a surrogate of biological Zn(II).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Yan; Wu, Jian-Feng; Tang, Yan-Yan

Highlights: • U II reduces cholesterol efflux in THP-1 macrophages. • U II decreases the expression of ABCA1. • Inhibition of the ERK/NF-κB pathway reduces U II effects on ABCA1 expression and cholesterol efflux. - Abstract: Objective: Foam cell formation in the arterial wall plays a key role in the development of atherosclerosis. Recent studies showed that Urotensin II (U II) is involved in the pathogenesis of atherosclerosis. Here we examined the effects of human U II on ATP-binding cassette transporter A1 (ABCA1) expression and the underlying mechanism in THP-1 macrophages. Methods and results: Cultured THP-1 macrophages were treated withmore » U II, followed by measuring the intracellular lipid contents, cholesterol efflux and ABCA1 levels. The results showed that U II dramatically decreased ABCA1 levels and impaired cholesterol efflux. However, the effects of U II on ABCA1 protein expression and cellular cholesterol efflux were partially reversed by inhibition of extracellular signal regulated kinase 1/2 (ERK1/2) and nuclear factor kappa B (NF-κB) activity, suggesting the potential roles of ERK1/2 and NF-κB in ABCA1 expression, respectively. Conclusion: Our current data indicate that U II may have promoting effects on the progression of atherosclerosis, likely through suppressing ABCA1 expression via activation of the ERK/NF-κB pathway and reducing cholesterol efflux to promote macrophage foam cell formation.« less

JPRS Report, Science & Technology, Japan: Symposium on Applications of Advanced Technology: Sensors

DTIC Science & Technology

1992-03-02

attempted as a part of a movement proposed by the [Text] author and his coworkers in 1983. In principle, it is a method that forcibly electrolyzes the...value of the current flowing at that time. The detection and Technology method is similar to that of the conventional phosphorus pentoxide sensor, and...electrolytes 3 ’:.i/ from the standpoint of developing energy-related tech- • ........ !ii. 4 nology. This method of water electrolysis is

Unified Multimodal Measurement for Performance Indication Research, Evaluation, and Effectiveness (UMMPIREE): Phase I Report

DTIC Science & Technology

2018-01-25

generally a researcher into methods and techniques (i.e., the science) of assessment. This stakeholder may observe ongoing events/experiments or may use... Research Visualization Tool. A first step toward finding a method to link research . 3.1.2 Phase II: Linking and the Network Approach During Phase I, we...innovations. In the former realm, UMMPIREE will develop a method to link assessments from different research studies to guide research

APOLLO II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sanchez, R.; Mondot, J.; Stankovski, Z.

1988-11-01

APOLLO II is a new, multigroup transport code under development at the Commissariat a l'Energie Atomique. The code has a modular structure and uses sophisticated software for data structuralization, dynamic memory management, data storage, and user macrolanguage. This paper gives an overview of the main methods used in the code for (a) multidimensional collision probability calculations, (b) leakage calculations, and (c) homogenization procedures. Numerical examples are given to demonstrate the potential of the modular structure of the code and the novel multilevel flat-flux representation used in the calculation of the collision probabilities.

Light-induced pH change and its application to solid phase extraction of trace heavy metals by high-magnetization Fe3O4@SiO2@TiO2 nanoparticles followed by inductively coupled plasma mass spectrometry detection.

PubMed

Zhang, Nan; Peng, Hanyong; Hu, Bin

2012-05-30

We report here the preparation of high-magnetization Fe(3)O(4)@SiO(2)@TiO(2) nanoparticles for solid phase extraction of trace amounts of Cd(II), Cr(III), Mn(II) and Cu(II) from environmental waters. The prepared nanoparticles were characterized by scanning electron micrograph (SEM) and transmission electron microscopy (TEM). The high-magnetization nanoparticles carrying the target metals could be easily and fast separated from the aqueous solution simply by applying an external magnetic field while no filtration or centrifugation was necessary. A light-induced hydroxide ion emitter, molecular malachite green carbinol base (MGCB) was applied to adjust pH value of solution for quantitative adsorption instead of the conventional used buffer. In the presence of UV light, MGCB gives out OH(-) ions, and this leads to an increase in the pH value without the aid of buffer solution. Using high-magnetization Fe(3)O(4)@SiO(2)@TiO(2) nanoparticles as the extraction material and the light-induced MGCB for pH adjustment, we developed an efficient and convenient two-step method for separation/preconcentration trace amounts of Cd(II), Cr(III), Mn(II) and Cu(II) in environmental water samples followed by inductively coupled plasma mass spectrometry (ICP-MS) detection. The parameters affecting the extraction such as MGCB concentration, exposal time, sample volume, eluent condition, and interfering ions have been investigated in detail. Under the optimized conditions, the limits of detection for Cd(II), Cr(III), Mn(II) and Cu(II) were 4.0, 2.6, 1.6 and 2.3 ng L(-1), respectively, and the relative standard deviations (RSDs, c=1 μg L(-1), n=7) were 3.6%, 4.5%, 4.0 and 4.1%, respectively. The proposed method has been validated using certified reference materials, and it has been successfully applied in the determination of trace Cd(II), Cr(III), Mn(II) and Cu(II) in environmental water samples. Copyright © 2012 Elsevier B.V. All rights reserved.

Development and validation of LC-HRMS and GC-NICI-MS methods for stereoselective determination of MDMA and its phase I and II metabolites in human urine

PubMed Central

Schwaninger, Andrea E.; Meyer, Markus R.; Huestis, Marilyn A.; Maurer, Hans H.

2013-01-01

3,4-Methylenedioxymethamphetamine (MDMA) is a racemic drug of abuse and its R- and S-enantiomers are known to differ in their dose-response curve. The S-enantiomer was shown to be eliminated at a higher rate than the R-enantiomer most likely explained by stereoselective metabolism that was observed in various in vitro experiments. The aim of this work was the development and validation of methods for evaluating the stereoselective elimination of phase I and particularly phase II metabolites of MDMA in human urine. Urine samples were divided into three different methods. Method A allowed stereoselective determination of the 4-hydroxy-3-methoxymethamphetamine (HMMA) glucuronides and only achiral determination of the intact sulfate conjugates of HMMA and 3,4-dihydroxymethamphetamine (DHMA) after C18 solid-phase extraction by liquid chromatography–high-resolution mass spectrometry with electrospray ionization. Method B allowed the determination of the enantiomer ratios of DHMA and HMMA sulfate conjugates after selective enzymatic cleavage and chiral analysis of the corresponding deconjugated metabolites after chiral derivatization with S-heptafluorobutyrylprolyl chloride using gas chromatography–mass spectrometry with negativeion chemical ionization. Method C allowed the chiral determination of MDMA and its unconjugated metabolites using method B without sulfate cleavage. The validation process including specificity, recovery, matrix effects, process efficiency, accuracy and precision, stabilities and limits of quantification and detection showed that all methods were selective, sensitive, accurate and precise for all tested analytes. PMID:21656610

Validation of quantitative light-induced fluorescence-digital (QLF-D) for the detection of approximal caries in vitro.

PubMed

Ko, Hae-Youn; Kang, Si-Mook; Kim, Hee Eun; Kwon, Ho-Keun; Kim, Baek-Il

2015-05-01

Detection of approximal caries lesions can be difficult due to their anatomical position. This study aimed to assess the ability of the quantitative light-induced fluorescence-digital (QLF-D) in detecting approximal caries, and to compare the performance with those of the International Caries Detection and Assessment System II (ICDAS II) and digital radiography (DR). Extracted permanent teeth (n=100) were selected and mounted in pairs. The simulation pairs were assessed by one calibrated dentist using each detection method. After all the examinations, the teeth (n=95) were sectioned and examined histologically as gold standard. The modalities were compared in terms of sensitivity, specificity, areas under receiver operating characteristic curves (AUROC) for enamel (D1) and dentine (D3) levels. The intra-examiner reliability was assessed for all modalities. At D1 threshold, the ICDAS II presented the highest sensitivity (0.80) while the DR showed the highest specificity (0.89); however, the methods with the greatest AUC values at D1 threshold were DR and QLF-D (0.80 and 0.80 respectively). At D3 threshold, the methods with the highest sensitivity were ICDAS II and QLF-D (0.64 and 0.64 respectively) while the method with the lowest sensitivity was DR (0.50). However, with regard to the AUC values at D3 threshold, the QLF-D presented the highest value (0.76). All modalities showed to have excellent intra-examiner reliability. The newly developed QLF-D was not only able to detect proximal caries, but also showed to have comparable performance to the visual inspection and radiography in detecting proximal caries. QLF-D has the potential to be a useful detection method for proximal caries. Copyright © 2015 Elsevier Ltd. All rights reserved.

Removal of Cu(II) in water by polymer enhanced ultrafiltration: Influence of polymer nature and pH.

PubMed

Kochkodan, Olga D; Kochkodan, Viktor M; Sharma, Virender K

2018-01-02

This study presents an efficient removal of Cu(II) in water using the polymer enhanced ultrafiltration (PEUF) method. Polymer of different molecular weight (MW) (polyethyleneimine (PEI), sodium lignosulfonates (SLS) and dextrans) were investigated to evaluate efficiency in removal of Cu(II) in water by the PEUF method. The decomposition of Cu(II)-polymer complex was also evaluated in order to reuse polymers. Cu(II) complexation depends on the MW of chelating polymer and the pH of feed solution. It was found that the Cu(II) rejection increased with the polymer dosage with high removal of Cu(II) when using PEI and SLS at a 10:20 (mg/mg) ratio ([Cu(II)]:[polymer]). It was found that the maximum chelating capacity was 15 mg of Cu(II) per 20 mg of PEI. The Cu(II)-PEI complex could be decomposed by acid addition and the polymer could be efficiently reused with multiple complexation-decomplexation cycles. A conceptual flow chart of the integrated process of efficient removal of Cu(II) by PEUF method is suggested.

Reduction of Heavy Metals by Cytochrome c(3)

DOE Office of Scientific and Technical Information (OSTI.GOV)

ABDELOUAS,A.; GONG,W.L.; LUTZE,W.

2000-01-18

We report on reduction and precipitation of Se(VI), Pb(II), CU(II), U(VI), Mo(VI), and Cr(VI) in water by cytochrome c{sub 3} isolated from Desulfomicrobium baczdatum [strain 9974]. The tetraheme protein cytochrome c{sub 3} was reduced by sodium dithionite. Redox reactions were monitored by UV-visible spectroscopy of cytochrome c{sub 3}. Analytical electron microscopy work showed that Se(VI), Pb(II), and CU(II) were reduced to the metallic state, U(W) and Mo(W) to U(IV) and Mo(IV), respectively, and Cr(VI) probably to Cr(III). U(IV) and Mo(W) precipitated as oxides and Cr(III) as an amorphous hydroxide. Cytochrome c{sub 3} was used repeatedly in the same solution withoutmore » loosing its effectiveness. The results suggest usage of cytochrome c{sub 3} to develop innovative and environmentally benign methods to remove heavy metals from waste- and groundwater.« less

Spectrophotometric Determination of Metoprolol Tartrate in Pharmaceutical Dosage Forms on Complex Formation with Cu(II)

PubMed Central

Cesme, Mustafa; Tarinc, Derya; Golcu, Aysegul

2011-01-01

A new, simple, sensitive and accurate spectrophotometric method has been developed for the assay of metoprolol tartrate (MPT), which is based on the complexation of drug with copper(II) [Cu(II)] at pH 6.0, using Britton-Robinson buffer solution, to produce a blue adduct. The latter has a maximum absorbance at 675 nm and obeys Beer's law within the concentration range 8.5-70 μg/mL. Regression analysis of the calibration data showed a good correlation coefficient (r = 0.998) with a limit of detection of 5.56 μg/mL. The proposed procedure has been successfully applied to the determination of this drug in its tablets. In addition, the spectral data and stability constant for the binuclear copper(II) complex of MPT (Cu2MPT2Cl2) have been reported.

Reconstitution of the Light Harvesting Chlorophyll a/b Pigment-Protein Complex into Developing Chloroplast Membranes Using a Dialyzable Detergent 1

PubMed Central

Darr, Sylvia C.; Arntzen, Charles J.

1986-01-01

Conditions were developed to isolate the light-harvesting chlorophyll-protein complex serving photosystem II (LHC-II) using a dialyzable detergent, octylpolyoxyethylene. This LHC-II was successfully reconstituted into partially developed chloroplast thylakoids of Hordeum vulgare var Morex (barley) seedlings which were deficient in LHC-II. Functional association of LHC-II with the photosystem II (PSII) core complex was measured by two independent functional assays of PSII sensitization by LHC-II. A 3-fold excess of reconstituted LHC-II was required to equal the activity of LHC developing in vivo. We suggest that a linker component may be absent in the partially developed membranes which is required for specific association of the PSII core complex and LHC-II. Images Fig. 1 PMID:16664744

Low- and high-spin iron (II) complexes studied by effective crystal field method combined with molecular mechanics.

PubMed

Darkhovskii, M B; Pletnev, I V; Tchougréeff, A L

2003-11-15

A computational method targeted to Werner-type complexes is developed on the basis of quantum mechanical effective Hamiltonian crystal field (EHCF) methodology (previously proposed for describing electronic structure of transition metal complexes) combined with the Gillespie-Kepert version of molecular mechanics (MM). It is a special version of the hybrid quantum/MM approach. The MM part is responsible for representing the whole molecule, including ligand atoms and metal ion coordination sphere, but leaving out the effects of the d-shell. The quantum mechanical EHCF part is limited to the metal ion d-shell. The method reproduces with reasonable accuracy geometry and spin states of the Fe(II) complexes with monodentate and polydentate aromatic ligands with nitrogen donor atoms. In this setting a single set of MM parameters set is shown to be sufficient for handling all spin states of the complexes under consideration. Copyright 2003 Wiley Periodicals, Inc.

Single Day Construction of Multigene Circuits with 3G Assembly.

PubMed

Halleran, Andrew D; Swaminathan, Anandh; Murray, Richard M

2018-05-18

The ability to rapidly design, build, and test prototypes is of key importance to every engineering discipline. DNA assembly often serves as a rate limiting step of the prototyping cycle for synthetic biology. Recently developed DNA assembly methods such as isothermal assembly and type IIS restriction enzyme systems take different approaches to accelerate DNA construction. We introduce a hybrid method, Golden Gate-Gibson (3G), that takes advantage of modular part libraries introduced by type IIS restriction enzyme systems and isothermal assembly's ability to build large DNA constructs in single pot reactions. Our method is highly efficient and rapid, facilitating construction of entire multigene circuits in a single day. Additionally, 3G allows generation of variant libraries enabling efficient screening of different possible circuit constructions. We characterize the efficiency and accuracy of 3G assembly for various construct sizes, and demonstrate 3G by characterizing variants of an inducible cell-lysis circuit.

Load rating and FRP retrofitting of bridge abutment timber piles.

DOT National Transportation Integrated Search

2016-05-01

This report details Phase II of the study titled Strengthening of Bridge Wood Piling Retrofits for Moment Resistance. Phase I of the research (project : R27-082) was focused on developing a load rating method for timber piles under eccentric load and...

DEVELOPMENT AND APPLICATION OF A NEW AIR POLLUTION MODELING SYSTEM--II. AEROSOL MODULE STRUCTURE AND DESIGN (R823186)

EPA Science Inventory

The methods used for simulating aerosol physical and chemical processes in a new air pollution modeling system are discussed and analyzed. Such processes include emissions, nucleation, coagulation, reversible chemistry, condensation, dissolution, evaporation, irreversible chem...

Controlled In Meso Phase Crystallization – A Method for the Structural Investigation of Membrane Proteins

PubMed Central

Kubicek, Jan; Schlesinger, Ramona; Baeken, Christian; Büldt, Georg; Schäfer, Frank; Labahn, Jörg

2012-01-01

We investigated in meso crystallization of membrane proteins to develop a fast screening technology which combines features of the well established classical vapor diffusion experiment with the batch meso phase crystallization, but without premixing of protein and monoolein. It inherits the advantages of both methods, namely (i) the stabilization of membrane proteins in the meso phase, (ii) the control of hydration level and additive concentration by vapor diffusion. The new technology (iii) significantly simplifies in meso crystallization experiments and allows the use of standard liquid handling robots suitable for 96 well formats. CIMP crystallization furthermore allows (iv) direct monitoring of phase transformation and crystallization events. Bacteriorhodopsin (BR) crystals of high quality and diffraction up to 1.3 Å resolution have been obtained in this approach. CIMP and the developed consumables and protocols have been successfully applied to obtain crystals of sensory rhodopsin II (SRII) from Halobacterium salinarum for the first time. PMID:22536388

Development and fabrication of improved Schottky power diodes, phases I and II

NASA Technical Reports Server (NTRS)

Cordes, L. F.; Garfinkle, M.; Taft, E. A.

1974-01-01

Reproducible methods for the fabrication of silicon Schottky diodes were developed for the metals tungsten, aluminum, conventional platinum silicide and low temperature platinum silicide. Barrier heights and barrier lowering were measured permitting the accurate prediction of ideal forward and reverse diode performance. Processing procedures were developed which permit the fabrication of large area (approximately 1 sqcm) mesa-geometry power Schottky diodes with forward and reverse characteristics that approach theoretical values.

Guidelines for using the Delphi Technique to develop habitat suitability index curves

USGS Publications Warehouse

Crance, Johnie H.

1987-01-01

Habitat Suitability Index (SI) curves are one method of presenting species habitat suitability criteria. The curves are often used with the Habitat Evaluation Procedures (HEP) and are necessary components of the Instream Flow Incremental Methodology (IFIM) (Armour et al. 1984). Bovee (1986) described three categories of SI curves or habitat suitability criteria based on the procedures and data used to develop the criteria. Category I curves are based on professional judgment, with 1ittle or no empirical data. Both Category II (utilization criteria) and Category III (preference criteria) curves have as their source data collected at locations where target species are observed or collected. Having Category II and Category III curves for all species of concern would be ideal. In reality, no SI curves are available for many species, and SI curves that require intensive field sampling often cannot be developed under prevailing constraints on time and costs. One alternative under these circumstances is the development and interim use of SI curves based on expert opinion. The Delphi technique (Pill 1971; Delbecq et al. 1975; Linstone and Turoff 1975) is one method used for combining the knowledge and opinions of a group of experts. The purpose of this report is to describe how the Delphi technique may be used to develop expert-opinion-based SI curves.

Design of a dual-function peptide probe as a binder of angiotensin II and an inducer of silver nanoparticle aggregation for use in label-free colorimetric assays.

PubMed

Okochi, Mina; Kuboyama, Masashi; Tanaka, Masayoshi; Honda, Hiroyuki

2015-09-01

Label-free colorimetric assays using metallic nanoparticles have received much recent attention, for their application in simple and sensitive methods for detection of biomolecules. Short peptide probes that can bind to analyte biomolecules are attractive ligands in molecular nanotechnology; however, identification of biological recognition motifs is usually based on trial-and-error experiments. Herein, a peptide probe was screened for colorimetric detection of angiotensin II (Ang II) using a mechanism for non-crosslinking aggregation of silver nanoparticles (AgNPs). The dual-function peptides, which bind to the analyte and induce AgNP aggregation, were identified using a two-step strategy: (1) screening of an Ang II-binding peptide from an Ang II receptor sequence library, using SPOT technology, which enable peptides synthesis on cellulose membranes via an Fmoc method and (2) selection of peptide probes that effectively induce aggregation of AgNPs using a photolinker modified peptide array. Using the identified peptide probe, KGKNKRRR, aggregation of AgNPs was detected by observation of a pink color in the absence of Ang II, whereas AgNPs remained dispersed in the presence of Ang II (yellow). The color changes were not observed in the presence of other hormone molecules. Ang II could be detected within 15 min, with a detection limit of 10 µM, by measuring the ratio of absorbance at 400 nm and 568 nm; the signal could also be observed with the naked eye. These data suggest that the peptide identified here could be used as a probe for simple and rapid colorimetric detection of Ang II. This strategy for the identification of functional peptides shows promise for the development of colorimetric detection of various diagnostically important biomolecules. Copyright © 2015 Elsevier B.V. All rights reserved.

MEFA (multiepitope fusion antigen)-Novel Technology for Structural Vaccinology, Proof from Computational and Empirical Immunogenicity Characterization of an Enterotoxigenic Escherichia coli (ETEC) Adhesin MEFA

PubMed Central

Duan, Qiangde; Lee, Kuo Hao; Nandre, Rahul M; Garcia, Carolina; Chen, Jianhan; Zhang, Weiping

2017-01-01

Vaccine development often encounters the challenge of virulence heterogeneity. Enterotoxigenic Escherichia coli (ETEC) bacteria producing immunologically heterogeneous virulence factors are a leading cause of children’s diarrhea and travelers’ diarrhea. Currently, we do not have licensed vaccines against ETEC bacteria. While conventional methods continue to make progress but encounter challenge, new computational and structure-based approaches are explored to accelerate ETEC vaccine development. In this study, we applied a structural vaccinology concept to construct a structure-based multiepitope fusion antigen (MEFA) to carry representing epitopes of the seven most important ETEC adhesins [CFA/I, CFA/II (CS1–CS3), CFA/IV (CS4–CS6)], simulated antigenic structure of the CFA/I/II/IV MEFA with computational atomistic modeling and simulation, characterized immunogenicity in mouse immunization, and examined the potential of structure-informed vaccine design for ETEC vaccine development. A tag-less recombinant MEFA protein (CFA/I/II/IV MEFA) was effectively expressed and extracted. Molecular dynamics simulations indicated that this MEFA immunogen maintained a stable secondary structure and presented epitopes on the protein surface. Empirical data showed that mice immunized with the tagless CFA/I/II/IV MEFA developed strong antigen-specific antibody responses, and mouse serum antibodies significantly inhibited in vitro adherence of bacteria expressing these seven adhesins. These results revealed congruence of antigen immunogenicity between computational simulation and empirical mouse immunization and indicated this tag-less CFA/I/II/IV MEFA potentially an antigen for a broadly protective ETEC vaccine, suggesting a potential application of MEFA-based structural vaccinology for vaccine design against ETEC and likely other pathogens. PMID:28944092

SLR precision analysis for LAGEOS I and II

NASA Astrophysics Data System (ADS)

Kizilsu, Gaye; Sahin, Muhammed

2000-10-01

This paper deals with the problem of properly weighting satellite observations which are non-uniform in quality. The technique, the variance component estimation method developed by Helmert, was first applied to the 1987 LAGEOS I SLR data by Sahin et al. (1992). This paper investigates the performance of the globally distributed SLR stations using the Helmert type variance component estimation. As well as LAGEOS I data, LAGEOS II data were analysed, in order to compare with the previously analysed 1987 LAGEOS I data. The LAGEOS I and II data used in this research were obtained from the NASA Crustal Dynamics Data Information System (CDDIS), which archives data acquired from stations operated by NASA and by other U.S. and international organizations. The data covers the years 1994, 1995 and 1996. The analysis is based on "full-rate" laser observations, which consist of hundreds to thousands of ranges per satellite pass. The software used is based on the SATAN package (SATellite ANalysis) developed at the Royal Greenwich Observatory in the UK.

Respiratory Infections in the U.S. Military: Recent Experience and Control

PubMed Central

Cooper, Michael J.; Myers, Christopher A.; Cummings, James F.; Vest, Kelly G.; Russell, Kevin L.; Sanchez, Joyce L.; Hiser, Michelle J.; Gaydos, Charlotte A.

2015-01-01

SUMMARY This comprehensive review outlines the impact of military-relevant respiratory infections, with special attention to recruit training environments, influenza pandemics in 1918 to 1919 and 2009 to 2010, and peacetime operations and conflicts in the past 25 years. Outbreaks and epidemiologic investigations of viral and bacterial infections among high-risk groups are presented, including (i) experience by recruits at training centers, (ii) impact on advanced trainees in special settings, (iii) morbidity sustained by shipboard personnel at sea, and (iv) experience of deployed personnel. Utilizing a pathogen-by-pathogen approach, we examine (i) epidemiology, (ii) impact in terms of morbidity and operational readiness, (iii) clinical presentation and outbreak potential, (iv) diagnostic modalities, (v) treatment approaches, and (vi) vaccine and other control measures. We also outline military-specific initiatives in (i) surveillance, (ii) vaccine development and policy, (iii) novel influenza and coronavirus diagnostic test development and surveillance methods, (iv) influenza virus transmission and severity prediction modeling efforts, and (v) evaluation and implementation of nonvaccine, nonpharmacologic interventions. PMID:26085551

The customization of APACHE II for patients receiving orthotopic liver transplants

PubMed Central

Moreno, Rui

2002-01-01

General outcome prediction models developed for use with large, multicenter databases of critically ill patients may not correctly estimate mortality if applied to a particular group of patients that was under-represented in the original database. The development of new diagnostic weights has been proposed as a method of adapting the general model – the Acute Physiology and Chronic Health Evaluation (APACHE) II in this case – to a new group of patients. Such customization must be empirically tested, because the original model cannot contain an appropriate set of predictive variables for the particular group. In this issue of Critical Care, Arabi and co-workers present the results of the validation of a modified model of the APACHE II system for patients receiving orthotopic liver transplants. The use of a highly heterogeneous database for which not all important variables were taken into account and of a sample too small to use the Hosmer–Lemeshow goodness-of-fit test appropriately makes their conclusions uncertain. PMID:12133174

Evaluation of 99mTc-MIBI in thyroid gland imaging for the diagnosis of amiodarone-induced thyrotoxicosis

PubMed Central

Zhang, Ruiguo

2017-01-01

Objective: Amiodarone-induced thyrotoxicosis (AIT) is caused by amiodarone as a side effect of cardiovascular disease treatment. Based on the differences in their pathological and physiological mechanisms, many methods have been developed so far to differentiate AIT subtypes such as colour flow Doppler sonography (CFDS) and 24-h radioiodine uptake (RAIU). However, these methods suffer from inadequate accuracy in distinguishing different types of AITs and sometimes lead to misdiagnosis and delayed treatments. Therefore, there is an unmet demand for an efficient method for accurate classification of AIT. Methods: Technetium-99 methoxyisobutylisonitrile (99mTc-MIBI) thyroid imaging was performed on 15 patients for AIT classification, and the results were compared with other conventional methods such as CFDS, RAIU and 99mTcO4 imaging. Results: High uptake and retention of MIBI in thyroid tissue is characteristic in Type I AIT, while in sharp contrast, low uptake of MIBI in the thyroid tissue was observed in Type II AIT. Mixed-type AIT shows uptake value between Types I and II. MIBI imaging outperforms other methods with a lower misdiagnosis rate. Conclusion: Among the methods evaluated, MIBI imaging enables an accurate identification of Type I, II and mixed-type AITs by showing distinct images for different types of AITs. The results obtained from our selected subjects revealed that MIBI imaging is a reliable method for diagnosis and classification of AITs and MIBI imaging has potential in the treatment of thyroid diseases. Advances in knowledge: 99mTc-MIBI imaging is a useful method for the diagnosis of AIT. It can distinguish different types of AITs especially for mixed-type AIT, which is usually difficult to treat. 99mTc-MIBI has potential advantages over conventional methods in the efficient treatment of AIT. PMID:28106465

Preliminary results of human PrPC protein studied by spectroscopic techniques

NASA Astrophysics Data System (ADS)

Nowakowski, Michał; Czapla-Masztafiak, Joanna; Kozak, Maciej; Zhukov, Igor; Zhukova, Lilia; Szlachetko, Jakub; Kwiatek, Wojciech M.

2017-11-01

Neurodegenerative diseases are one of the malfunctions of human nervous system, being a class of complex and prominent pathologies. The human prion Protease Resistant Protein (PrP) is protein regulating copper metabolism in mammalian cells through binding of Cu(II) ions to specific fragments. Nowadays misfolding of this protein is associated with development of prion diseases. Therefore, it is crucial to obtain structural information about coordination of Cu(II) by PrP protein. Herein, we report X-ray absorption spectroscopy (XAS) measurements, carried out on SuperXAS beamline (SLS, PSI Villigen) on PrPC-Cu(II) complexes. Obtained results were compared with theoretical predictions done by FEFF 9.6 software. Complementary to XAS data, Atomic Force Microscopy (AFM) measurements were conducted to obtain low resolution structural information about prepared sample that allow to develop protocol of fixing PrPC molecules on solid substrate used for further experiments. It has been established that folded C-terminal domain of PrPC protein has around 5 nm in diameter. Presented results showed that both XAS and AFM methods are useful tools in detailed examination of complexes of human PrPC either with Cu(II) or with other divalent metal ions.

PyXRF: Python-based X-ray fluorescence analysis package

NASA Astrophysics Data System (ADS)

Li, Li; Yan, Hanfei; Xu, Wei; Yu, Dantong; Heroux, Annie; Lee, Wah-Keat; Campbell, Stuart I.; Chu, Yong S.

2017-09-01

We developed a python-based fluorescence analysis package (PyXRF) at the National Synchrotron Light Source II (NSLS-II) for the X-ray fluorescence-microscopy beamlines, including Hard X-ray Nanoprobe (HXN), and Submicron Resolution X-ray Spectroscopy (SRX). This package contains a high-level fitting engine, a comprehensive commandline/ GUI design, rigorous physics calculations, and a visualization interface. PyXRF offers a method of automatically finding elements, so that users do not need to spend extra time selecting elements manually. Moreover, PyXRF provides a convenient and interactive way of adjusting fitting parameters with physical constraints. This will help us perform quantitative analysis, and find an appropriate initial guess for fitting. Furthermore, we also create an advanced mode for expert users to construct their own fitting strategies with a full control of each fitting parameter. PyXRF runs single-pixel fitting at a fast speed, which opens up the possibilities of viewing the results of fitting in real time during experiments. A convenient I/O interface was designed to obtain data directly from NSLS-II's experimental database. PyXRF is under open-source development and designed to be an integral part of NSLS-II's scientific computation library.

Assessment of type II diabetes mellitus using irregularly sampled measurements with missing data.

PubMed

Barazandegan, Melissa; Ekram, Fatemeh; Kwok, Ezra; Gopaluni, Bhushan; Tulsyan, Aditya

2015-04-01

Diabetes mellitus is one of the leading diseases in the developed world. In order to better regulate blood glucose in a diabetic patient, improved modelling of insulin-glucose dynamics is a key factor in the treatment of diabetes mellitus. In the current work, the insulin-glucose dynamics in type II diabetes mellitus can be modelled by using a stochastic nonlinear state-space model. Estimating the parameters of such a model is difficult as only a few blood glucose and insulin measurements per day are available in a non-clinical setting. Therefore, developing a predictive model of the blood glucose of a person with type II diabetes mellitus is important when the glucose and insulin concentrations are only available at irregular intervals. To overcome these difficulties, we resort to online sequential Monte Carlo (SMC) estimation of states and parameters of the state-space model for type II diabetic patients under various levels of randomly missing clinical data. Our results show that this method is efficient in monitoring and estimating the dynamics of the peripheral glucose, insulin and incretins concentration when 10, 25 and 50% of the simulated clinical data were randomly removed.

Rapid and sensitive detection of Feline immunodeficiency virus using an insulated isothermal PCR-based assay with a point-of-need PCR detection platform.

PubMed

Wilkes, Rebecca Penrose; Kania, Stephen A; Tsai, Yun-Long; Lee, Pei-Yu Alison; Chang, Hsiu-Hui; Ma, Li-Juan; Chang, Hsiao-Fen Grace; Wang, Hwa-Tang Thomas

2015-07-01

Feline immunodeficiency virus (FIV) is an important infectious agent of cats. Clinical syndromes resulting from FIV infection include immunodeficiency, opportunistic infections, and neoplasia. In our study, a 5' long terminal repeat/gag region-based reverse transcription insulated isothermal polymerase chain reaction (RT-iiPCR) was developed to amplify all known FIV strains to facilitate point-of-need FIV diagnosis. The RT-iiPCR method was applied in a point-of-need PCR detection platform--a field-deployable device capable of generating automatically interpreted RT-iiPCR results from nucleic acids within 1 hr. Limit of detection 95% of FIV RT-iiPCR was calculated to be 95 copies standard in vitro transcription RNA per reaction. Endpoint dilution studies with serial dilutions of an ATCC FIV type strain showed that the sensitivity of lyophilized FIV RT-iiPCR reagent was comparable to that of a reference nested PCR. The established reaction did not amplify any nontargeted feline pathogens, including Felid herpesvirus 1, feline coronavirus, Feline calicivirus, Feline leukemia virus, Mycoplasma haemofelis, and Chlamydophila felis. Based on analysis of 76 clinical samples (including blood and bone marrow) with the FIV RT-iiPCR, test sensitivity was 97.78% (44/45), specificity was 100.00% (31/31), and agreement was 98.65% (75/76), determined against a reference nested-PCR assay. A kappa value of 0.97 indicated excellent correlation between these 2 methods. The lyophilized FIV RT-iiPCR reagent, deployed on a user-friendly portable device, has potential utility for rapid and easy point-of-need detection of FIV in cats. © 2015 The Author(s).

Construction and Validation of Attitudes Toward Plagiarism Questionnaire

PubMed Central

Mavrinac, Martina; Brumini, Gordana; Bilić-Zulle, Lidija; Petrovečki, Mladen

2010-01-01

Aim To develop and test the psychometric characteristics of a questionnaire measuring attitudes toward plagiarism. Methods Participants were 227 undergraduates and graduate students from three Croatian universities, with a median age of 21 years (range 18 to 48). Research was conducted from March to June 2009. For the purpose of construction of the first version of the questionnaire, 67 statements (items) were developed. The statements were based on the relevant literature and were developed following rules and recommendations for questionnaire writing, and 36 items were chosen for final validation. Factor analysis was used to find out the factor structure of the questionnaire and to measure construct validity. Results The final version of the questionnaire consisted of 29 items divided into a three-factor structure: factor I – positive attitude toward plagiarism (12 items); factor II – negative attitude toward plagiarism (7 items); and factor III – subjective norms toward plagiarism (10 items). Cronbach α was calculated to confirm the reliability of the scale: factor I – α = 0.83; factor II – α = 0.79; and factor III – α = 0.85. Correlations between factors were: -0.37 between I and II, -0.41 between I and III, and +0.31 between II and III. Conclusion Attitudes Toward Plagiarism questionnaire was developed, with good psychometric characteristics. It will be used in future research as a standardized tool for measuring attitudes toward plagiarism. PMID:20564761

Determination of the main solid-state form of albendazole in bulk drug, employing Raman spectroscopy coupled to multivariate analysis.

PubMed

Calvo, Natalia L; Arias, Juan M; Altabef, Aída Ben; Maggio, Rubén M; Kaufman, Teodoro S

2016-09-10

Albendazole (ALB) is a broad-spectrum anthelmintic, which exhibits two solid-state forms (Forms I and II). The Form I is the metastable crystal at room temperature, while Form II is the stable one. Because the drug has poor aqueous solubility and Form II is less soluble than Form I, it is desirable to have a method to assess the solid-state form of the drug employed for manufacturing purposes. Therefore, a Partial Least Squares (PLS) model was developed for the determination of Form I of ALB in its mixtures with Form II. For model development, both solid-state forms of ALB were prepared and characterized by microscopic (optical and with normal and polarized light), thermal (DSC) and spectroscopic (ATR-FTIR, Raman) techniques. Mixtures of solids in different ratios were prepared by weighing and mechanical mixing of the components. Their Raman spectra were acquired, and subjected to peak smoothing, normalization, standard normal variate correction and de-trending, before performing the PLS calculations. The optimal spectral region (1396-1280cm(-1)) and number of latent variables (LV=3) were obtained employing a moving window of variable size strategy. The method was internally validated by means of the leave one out procedure, providing satisfactory statistics (r(2)=0.9729 and RMSD=5.6%) and figures of merit (LOD=9.4% and MDDC=1.4). Furthermore, the method's performance was also evaluated by analysis of two validation sets. Validation set I was used for assessment of linearity and range and Validation set II, to demonstrate accuracy and precision (Recovery=101.4% and RSD=2.8%). Additionally, a third set of spiked commercial samples was evaluated, exhibiting excellent recoveries (94.2±6.4%). The results suggest that the combination of Raman spectroscopy with multivariate analysis could be applied to the assessment of the main crystal form and its quantitation in samples of ALB bulk drug, in the routine quality control laboratory. Copyright © 2016 Elsevier B.V. All rights reserved.

A MULTIPLE TESTING OF THE ABC METHOD AND THE DEVELOPMENT OF A SECOND-GENERATION MODEL. PART II, TEST RESULTS AND AN ANALYSIS OF RECALL RATIO.

ERIC Educational Resources Information Center

ALTMANN, BERTHOLD

AFTER A BRIEF SUMMARY OF THE TEST PROGRAM (DESCRIBED MORE FULLY IN LI 000 318), THE STATISTICAL RESULTS TABULATED AS OVERALL "ABC (APPROACH BY CONCEPT)-RELEVANCE RATIOS" AND "ABC-RECALL FIGURES" ARE PRESENTED AND REVIEWED. AN ABSTRACT MODEL DEVELOPED IN ACCORDANCE WITH MAX WEBER'S "IDEALTYPUS" ("DIE OBJEKTIVITAET…

Teaching Standard English as a Second Dialect to Primary School Children in Hilo, Hawaii. Volume I of II Volumes. Final Report.

ERIC Educational Resources Information Center

Peterson, Robert O. H.

This document describes a four-year program designed to develop and test a method for teaching standard English to nonstandard dialect speakers in the first four grades of elementary school in Hilo, Hawaii. Chapters in this first volume are (1) Introduction, (2) Project Site and Evaluation Strategy, (3) Instrumentation, (4) Development of Lesson…

A Quality Improvement Customer Service Process and CSS [Customer Service System]. Burlington County College Employee Development Series, Volumes I & II.

ERIC Educational Resources Information Center

Burlington County Coll., Pemberton, NJ.

Prepared for use by staff in development workshops at Burlington County College (BCC), in New Jersey, this handbook offers college-wide guidelines for improving the quality of service provided to internal and external customers, and reviews key elements of BCC's Customer Service System (CSS), a computerized method of recording and following-up on…

Performance of TcI/TcVI/TcII Chagas-Flow ATE-IgG2a for universal and genotype-specific serodiagnosis of Trypanosoma cruzi infection

PubMed Central

Alessio, Glaucia Diniz; de Araújo, Fernanda Fortes; Côrtes, Denise Fonseca; Sales Júnior, Policarpo Ademar; Lima, Daniela Cristina; Gomes, Matheus de Souza; do Amaral, Laurence Rodrigues; Xavier, Marcelo Antônio Pascoal; Teixeira-Carvalho, Andréa; Martins-Filho, Olindo Assis; de Lana, Marta

2017-01-01

Distinct Trypanosoma cruzi genotypes have been considered relevant for patient management and therapeutic response of Chagas disease. However, typing strategies for genotype-specific serodiagnosis of Chagas disease are still unavailable and requires standardization for practical application. In this study, an innovative TcI/TcVI/TcII Chagas Flow ATE-IgG2a technique was developed with applicability for universal and genotype-specific diagnosis of T. cruzi infection. For this purpose, the reactivity of serum samples (percentage of positive fluorescent parasites-PPFP) obtained from mice chronically infected with TcI/Colombiana, TcVI/CL or TcII/Y strain as well as non-infected controls were determined using amastigote-AMA, trypomastigote-TRYPO and epimastigote-EPI in parallel batches of TcI, TcVI and TcII target antigens. Data demonstrated that “α-TcII-TRYPO/1:500, cut-off/PPFP = 20%” presented an excellent performance for universal diagnosis of T. cruzi infection (AUC = 1.0, Se and Sp = 100%). The combined set of attributes “α-TcI-TRYPO/1:4,000, cut-off/PPFP = 50%”, “α-TcII-AMA/1:1,000, cut-off/PPFP = 40%” and “α-TcVI-EPI/1:1,000, cut-off/PPFP = 45%” showed good performance to segregate infections with TcI/Colombiana, TcVI/CL or TcII/Y strain. Overall, hosts infected with TcI/Colombiana and TcII/Y strains displayed opposite patterns of reactivity with “α-TcI TRYPO” and “α-TcII AMA”. Hosts infected with TcVI/CL strain showed a typical interweaved distribution pattern. The method presented a good performance for genotype-specific diagnosis, with global accuracy of 69% when the population/prototype scenario include TcI, TcVI and TcII infections and 94% when comprise only TcI and TcII infections. This study also proposes a receiver operating reactivity panel, providing a feasible tool to classify serum samples from hosts infected with distinct T. cruzi genotypes, supporting the potential of this method for universal and genotype-specific diagnosis of T. cruzi infection. PMID:28333926

Bovine serum albumin-Cu(II) hybrid nanoflowers: An effective adsorbent for solid phase extraction and slurry sampling flame atomic absorption spectrometric analysis of cadmium and lead in water, hair, food and cigarette samples.

PubMed

Yilmaz, Erkan; Ocsoy, Ismail; Ozdemir, Nalan; Soylak, Mustafa

2016-02-04

Herein, the synthesis of bovine serum albumin-Cu(II) hybrid nanoflowers (BSA-NFs) through the building blocks of bovine serum albumin (BSA) and copper(II) ions in phosphate buffered saline (PBS) and their use as adsorbent for cadmium and lead ions are reported. The BSA-NFs, for the first time, were efficiently utilized as novel adsorbent for solid phase extraction (SPE) of cadmium and lead ions in water, food, cigarette and hair samples. The method is based on the separation and pre-concentration of Cd(II) and Pb(II) by BSA-NFs prior to determination by slurry analysis via flame atomic absorption spectrometry (FAAS). The analytes were adsorbed on BSA-NFs under the vortex mixing and then the ion-loaded slurry was separated and directly introduced into the flame AAS nebulizer by using a hand-made micro sample introduction system to eliminate a number of drawbacks. The effects of analytical key parameters, such as pH, amount of BSA-NFs, vortexing time, sample volume, and matrix effect of foreign ions on adsorbing of Cd(II) and Pb(II) were systematically investigated and optimized. The limits of detection (LODs) for Cd(II) and Pb(II) were calculated as 0.37 μg L(-)(1) and 8.8 μg L(-)(1), respectively. The relative standard deviation percentages (RSDs) (N = 5) for Cd(II) and Pb(II) were 7.2%, and 5.0%, respectively. The accuracy of the developed procedure was validated by the analysis of certified reference materials (TMDA-53.3 Fortified Water, TMDA-70 Fortified Water, SPS-WW2 Waste Water, NCSDC-73349 Bush Branches and Leaves) and by addition/recovery analysis. The quantitative recoveries were obtained for the analysis of certified reference materials and addition/recovery tests. The method was successfully applied to the analysis of cadmium and lead in water, food, cigarette and hair samples. Copyright © 2015 Elsevier B.V. All rights reserved.

Fast sweeping methods for hyperbolic systems of conservation laws at steady state II

NASA Astrophysics Data System (ADS)

Engquist, Björn; Froese, Brittany D.; Tsai, Yen-Hsi Richard

2015-04-01

The idea of using fast sweeping methods for solving stationary systems of conservation laws has previously been proposed for efficiently computing solutions with sharp shocks. We further develop these methods to allow for a more challenging class of problems including problems with sonic points, shocks originating in the interior of the domain, rarefaction waves, and two-dimensional systems. We show that fast sweeping methods can produce higher-order accuracy. Computational results validate the claims of accuracy, sharp shock curves, and optimal computational efficiency.

Reduced-molecular-weight derivatives of frost grape polysaccharide

USDA-ARS?s Scientific Manuscript database

A new Type II arabinogalactan was recently described as an abundant gum exudate from stems of wildfrost grape (Vitus riparia Michx.). The purpose of the current study is to more thoroughly characterize the physical properties of this frost grape polysaccharide (FGP), and develop methods to modify th...

REDUCED COST SEWER PIPE RELINING USING ULTRASONIC TAPE LAMINATION - PHASE II

EPA Science Inventory

During the Phase I program, Foster-Miller developed techniques based on Ultrasonic Tape Lamination (UTL) for joining of plasticized PVC sewer pipe liner. This effort was undertaken in response to a need for environmentally sound and cost-effective methods for rehabilitation of...

24 CFR 1006.205 - Development.

Code of Federal Regulations, 2010 CFR

2010-04-01

... homebuyers through: (i) Down payment assistance; (ii) Closing costs assistance; (iii) Direct lending; and (iv... assisted and unassisted units are not comparable, the actual costs may be determined based upon a method of cost allocation. If the assisted and unassisted units are comparable in terms of size, features, and...

Surface pavement solutions for poor subgrade conditions phase II : performance analysis of test sections and implementation guidelines : summary.

DOT National Transportation Integrated Search

2010-12-01

Several areas within FDOT Districts 4 and 6 contain thick layers of organic soils at relatively shallow depths. Roads built on these soft compressible soils : often develop premature cracking, distortion, and settlement. Traditional repair methods, s...

Method for estimating the morphological significance of simple forms of crystals from X-ray data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Treivus, E. B., E-mail: sbobr1@bk.ru

2010-09-15

When developing V.I. Mikheev and I.I. Shafranovskii's method for estimating the morphological significance of faces of different simple forms from X-ray reflection intensities, a way to approximately evaluate the morphological significance of simple forms on crystals from the structure amplitudes of the corresponding atomic planes is proposed. The potential for this approach is demonstrated by the examples of marcasite and zircon.

Application Guide for Heat Recovery Incinerators.

DTIC Science & Technology

1986-02-01

of the absorption cycle to vaporize the refrigerant, typically an aqueous ammonia . The refrigerant then follows the typical refrigeration cycle...this third level of iteration, the information gathered in level II should be updated if necessary and verified. Use the NCEL survey method (see...and quantity of the solid waste can be determined by applying procedures set forth in Appendix B. For level III, NCEL has developed a survey method

Validation of Digital Systems in Avionics and Flight Control Applications Handbook. Volume 1.

DTIC Science & Technology

1983-07-01

will also be available to Airways Facilities, Systems Research and Development Service, Air Traffic Control Service, and Flight Standards elements...2114, March 12-14, 1979. 3. Validation Methods Research for Fault-Tolerant Avionics and Control Systems-- *r Working Group Meeting II, NASA...command generation with the multiple methods becoming avail- able for closure of the outer control loop necessitates research on alternative integration

An MRI-Compatible Robotic System With Hybrid Tracking for MRI-Guided Prostate Intervention

PubMed Central

Krieger, Axel; Iordachita, Iulian I.; Guion, Peter; Singh, Anurag K.; Kaushal, Aradhana; Ménard, Cynthia; Pinto, Peter A.; Camphausen, Kevin; Fichtinger, Gabor

2012-01-01

This paper reports the development, evaluation, and first clinical trials of the access to the prostate tissue (APT) II system—a scanner independent system for magnetic resonance imaging (MRI)-guided transrectal prostate interventions. The system utilizes novel manipulator mechanics employing a steerable needle channel and a novel six degree-of-freedom hybrid tracking method, comprising passive fiducial tracking for initial registration and subsequent incremental motion measurements. Targeting accuracy of the system in prostate phantom experiments and two clinical human-subject procedures is shown to compare favorably with existing systems using passive and active tracking methods. The portable design of the APT II system, using only standard MRI image sequences and minimal custom scanner interfacing, allows the system to be easily used on different MRI scanners. PMID:22009867

Endoscopically assisted intraoral modified Le Fort II type midfacial advancement using piezoelectric surgery and an intraoperative RED system.

PubMed

Hara, Shingo; Mitsugi, Masaharu; Kanno, Takahiro; Nomachi, Akihiko; Kawakami, Seiichi; Tatemoto, Yukihiro

2013-02-01

The Le Fort II midfacial advancement appears to be an effective surgical method for the treatment of severe midfacial-nose hypoplasia with a skeletal class III malocclusion, which is usually combined with syndromic midfacial anomalies. However, the conventional surgical method requires the coronal approach, including a coronal incision, together with other surgical approaches, such as an intraoral incision. Therefore, surgeons often hesitate to propose this type of osteotomy, even for patients who develop severe nonsyndromic midfacial-nose hypoplasia. This report presents a new surgical approach for performing a safe Le Fort II osteotomy for nasomaxillary, midfacial corrective advancement via a solely intraoral approach. Surgery was performed with endoscopically assisted piezoelectric surgery. The osteotomized nasomaxillary Le Fort II segment was successfully protracted without aggressive down-fracture procedures with the sole intraoperative use of a rigid external distraction (RED) system, followed by internal rigid fixation, and the subsequent removal of the RED system. Seven patients (all patients were nonsyndromic, but 2 had cleft lip and palate, and an average age of 19.9 years) were included in this study. The degrees of midfacial advancement at the base of nasal bone (the top edge of the modified Le Fort II segment) that was osteotomized and at maxillary point A was 8.3 mm (range 5.8 mm to 10.5mm) and 8.5 mm (range 5.9 mm to 9.8 mm), respectively. This new method less invasively facilitates safe, secure, and ideal nasomaxillary midfacial protraction to yield a satisfactory resultant facial profile and favorable occlusion in patients with severe midfacial-nose hypoplasia and skeletal class III malocclusions. Copyright © 2013 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

Extraction of trace amounts of mercury with sodium dodecyle sulphate-coated magnetite nanoparticles and its determination by flow injection inductively coupled plasma-optical emission spectrometry.

PubMed

Faraji, Mohammad; Yamini, Yadollah; Rezaee, Mohammad

2010-05-15

A new method for solid-phase extraction and preconcentration of trace amounts Hg(II) from environmental samples was developed by using sodium dodecyle sulphate-coated magnetite nanoparticles (SDS-coated Fe(3)O(4) NPs) as a new extractant. The procedure is based on the adsorption of the analyte, as mercury-Michler's thioketone [Hg(2)(TMK)(4)](2+) complex on the negatively charged surface of the SDS-coated Fe(3)O(4) NPs and then elution of the preconcentrated mercury from the surface of the SDS-coated Fe(3)O(4) NPs prior to its determination by flow injection inductively coupled plasma-optical emission spectrometry. The effects of pH, TMK concentration, SDS and Fe(3)O(4) NPs amounts, eluent type, sample volume and interfering ions on the recovery of the analyte were investigated. Under optimized conditions, the calibration curve was linear in the range of 0.2-100ngmL(-1) with r(2)=0.9994 (n=8). The limit of detection for Hg(II) determination was 0.04ngmL(-1). Also, relative standard deviation (R.S.D.) for the determination of 2 and 50ngmL(-1) of Hg(II) was 5.2 and 4.7% (n=6), respectively. Due to the quantitative extraction of Hg(II) from 1000mL of the sample solution an enhancement factor as large as 1230-fold can be obtained. The proposed method has been validated using a certified reference materials, and also the method has been applied successfully for the determination of Hg(II) in aqueous samples.

Development and evaluation of a culture-independent method for source determination of fecal wastes in surface and storm waters using reverse transcriptase-PCR detection of FRNA coliphage genogroup gene sequences.

PubMed

Paar, Jack; Doolittle, Mark M; Varma, Manju; Siefring, Shawn; Oshima, Kevin; Haugland, Richard A

2015-05-01

A method, incorporating recently improved reverse transcriptase-PCR primer/probe assays and including controls for detecting interferences in RNA recovery and analysis, was developed for the direct, culture-independent detection of genetic markers from FRNA coliphage genogroups I, II & IV in water samples. Results were obtained from an initial evaluation of the performance of this method in analyses of waste water, ambient surface water and stormwater drain and outfall samples from predominantly urban locations. The evaluation also included a comparison of the occurrence of the FRNA genetic markers with genetic markers from general and human-related bacterial fecal indicators determined by current or pending EPA-validated qPCR methods. Strong associations were observed between the occurrence of the putatively human related FRNA genogroup II marker and the densities of the bacterial markers in the stormwater drain and outfall samples. However fewer samples were positive for FRNA coliphage compared to either the general bacterial fecal indicator or the human-related bacterial fecal indicator markers particularly for ambient water samples. Together, these methods show promise as complementary tools for the identification of contaminated storm water drainage systems as well as the determination of human and non-human sources of contamination. Published by Elsevier B.V.

Performance of the score systems Acute Physiology and Chronic Health Evaluation II and III at an interdisciplinary intensive care unit, after customization

PubMed Central

Markgraf, Rainer; Deutschinoff, Gerd; Pientka, Ludger; Scholten, Theo; Lorenz, Cristoph

2001-01-01

Background: Mortality predictions calculated using scoring scales are often not accurate in populations other than those in which the scales were developed because of differences in case-mix. The present study investigates the effect of first-level customization, using a logistic regression technique, on discrimination and calibration of the Acute Physiology and Chronic Health Evaluation (APACHE) II and III scales. Method: Probabilities of hospital death for patients were estimated by applying APACHE II and III and comparing these with observed outcomes. Using the split sample technique, a customized model to predict outcome was developed by logistic regression. The overall goodness-of-fit of the original and the customized models was assessed. Results: Of 3383 consecutive intensive care unit (ICU) admissions over 3 years, 2795 patients could be analyzed, and were split randomly into development and validation samples. The discriminative powers of APACHE II and III were unchanged by customization (areas under the receiver operating characteristic [ROC] curve 0.82 and 0.85, respectively). Hosmer-Lemeshow goodness-of-fit tests showed good calibration for APACHE II, but insufficient calibration for APACHE III. Customization improved calibration for both models, with a good fit for APACHE III as well. However, fit was different for various subgroups. Conclusions: The overall goodness-of-fit of APACHE III mortality prediction was improved significantly by customization, but uniformity of fit in different subgroups was not achieved. Therefore, application of the customized model provides no advantage, because differences in case-mix still limit comparisons of quality of care. PMID:11178223

Simultaneous determination and pharmacokinetic study of Atractylenolide I, II and III in rat plasma after intragastric administration of Baizhufuling extract and Atractylodis extract by UPLC-MS/MS.

PubMed

Yan, Han; Sun, Yuanyuan; Zhang, Qili; Yang, Mingjing; Wang, Xiaorui; Wang, Yang; Yu, Zhiguo; Zhao, Yunli

2015-07-01

A simple and rapid ultra high performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) method was developed for the simultaneous determination of Atractylenolide I, II and III in rat plasma. Plasma samples were processed by liquid-liquid extraction with ethyl acetate, using schisandrin as internal standard (IS). Chromatographic separation was accomplished on a Thermo Hypersil GOLD C18 column (2.1mm×50mm, 1.9μm) with mobile phase consisting of acetonitrile and 0.1% formic acid-water (50:50, v/v). The detection was carried out by ESI-MS (positive ionization mode) and low-energy collision dissociation tandem mass spectrometric analyses using the multiple-reaction monitoring (MRM) scan mode. The quantification was performed using the transitions of the protonated molecule→product ion at m/z 231.0→185.1 for Atractylenolide I, at m/z 233.1→187.1 for Atractylenolide II and at m/z 249.1→231.1 for Atractylenolide III, respectively. Method validation revealed excellent linearity over investigated range together with satisfactory intra- and inter-day precision, accuracy, matrix effects and extraction recoveries. This method was successfully applied to the comparative pharmacokinetic study of Atractylenolide I, II and III in rat plasma after intragastric administration of Baizhufuling extract and Atractylodis extract. Copyright © 2015 Elsevier B.V. All rights reserved.

Development of an ELA-DRA gene typing method based on pyrosequencing technology.

PubMed

Díaz, S; Echeverría, M G; It, V; Posik, D M; Rogberg-Muñoz, A; Pena, N L; Peral-García, P; Vega-Pla, J L; Giovambattista, G

2008-11-01

The polymorphism of equine lymphocyte antigen (ELA) class II DRA gene had been detected by polymerase chain reaction-single-strand conformational polymorphism (PCR-SSCP) and reference strand-mediated conformation analysis. These methodologies allowed to identify 11 ELA-DRA exon 2 sequences, three of which are widely distributed among domestic horse breeds. Herein, we describe the development of a pyrosequencing-based method applicable to ELA-DRA typing, by screening samples from eight different horse breeds previously typed by PCR-SSCP. This sequence-based method would be useful in high-throughput genotyping of major histocompatibility complex genes in horses and other animal species, making this system interesting as a rapid screening method for animal genotyping of immune-related genes.

SKYSINE-II procedure: calculation of the effects of structure design on neutron, primary gamma-ray and secondary gamma-ray dose rates in air

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lampley, C.M.

1979-01-01

An updated version of the SKYSHINE Monte Carlo procedure has been developed. The new computer code, SKYSHINE-II, provides a substantial increase in versatility in that the program possesses the ability to address three types of point-isotropic radiation sources: (1) primary gamma rays, (2) neutrons, and (3) secondary gamma rays. In addition, the emitted radiation may now be characterized by an energy emission spectrum product of a new energy-dependent atmospheric transmission data base developed by Radiation Research Associates, Inc. for each of the three source types described above. Most of the computational options present in the original program have been retainedmore » in the new version. Hence, the SKYSHINE-II computer code provides a versatile and viable tool for the analysis of the radiation environment in the vicinity of a building structure containing radiation sources, situated within the confines of a nuclear power plant. This report describes many of the calculational methods employed within the SKYSHINE-II program. A brief description of the new data base is included. Utilization instructions for the program are provided for operation of the SKYSHINE-II code on the Brookhaven National Laboratory Central Scientific Computing Facility. A listing of the source decks, block data routines, and the new atmospheric transmission data base are provided in the appendices of the report.« less

Multilocus genetic characterization of two ant vectors (Group II "Dirty 22" species) known to contaminate food and food products and spread foodborne pathogens.

PubMed

Sulaiman, Irshad M; Anderson, Mickey; Oi, David H; Simpson, Steven; Kerdahi, Khalil

2012-08-01

The U.S. Food and Drug Administration utilizes the presence of filth and extraneous materials as one of the criteria for implementing regulatory actions and assessing adulteration of food products of public health importance. Twenty-two prevalent pest species (also known as the ''Dirty 22'' species) have been considered by this agency as possible vehicles for the spread of foodborne diseases, and the presence of these species is considered an indicator of unsanitary conditions in food processing and storage facilities. In a previous study, we further categorized the Dirty 22 species into four groups: group I includes four cockroach species, group II includes two ant species, group III includes 12 fly species, and group IV includes four rodent species. Here, we describe the development of three nested PCR primer sets and multilocus genetic characterization by amplifying the small subunit rRNA, elongation factor 1-alpha, and wingless (WNT-1) genes of group II Dirty 22 ant species Monomorium pharaonis and Solenopsis molesta. These novel group II Dirty 22 species-specific nested PCR primer sets can be used when the specimens cannot be identified using conventional microscopic methods. These newly developed assays will provide correct identification of group II Dirty 22 ant species, and the information can be used in the control of foodborne pathogens.

Choice and validation of a near infrared spectroscopic application for the identity control of starting materials. practical experience with the EU draft Note for Guidance on the use of near infrared spectroscopy by the pharmaceutical industry and the data to be forwarded in part II of the dossier for a marketing authorization.

PubMed

Vredenbregt, M J; Caspers, P W J; Hoogerbrugge, R; Barends, D M

2003-11-01

Recently the CPMP/CVMP sent out for consultation the draft Note for Guidance (dNfG) on the use of near infrared spectroscopy (NIRS) by the pharmaceutical industry and the data to be forwarded in part II of the dossier for a marketing authorization. We explored the practicability of this dNfG with respect to the verification of the correct identity of starting materials in a generic tablet-manufacturing site. Within the boundaries of the dNfG, a release procedure was developed for 12 substances containing structurally related compounds and substances differing only in particle size. For the method development literature data were also taken into consideration. Good results were obtained with wavelength correlation (WC), applied on raw spectra or second derivative spectra both without smoothing. The defined threshold of 0.98 for raw spectra differentiated between all molecular structures. Both methods were found to be robust over a period of 1 year. For the differentiation between the different particle sizes a subsequent second chemometric technique had to be used. Soft independent modelling of class analogy (SIMCA) with a probability level of 0.01 proved suitable. Internal and external validation I according to the dNfG showed no incorrect rejections or false acceptances. External validation II according to the dNfG was carried out with 95 potentially interfering substances from which 46 were tested experimentally. Macrogol 400 was not distinguished from macrogol 300. For the complete verification of the identity of macrogol 300 test A of the European Pharmacopoeia is needed in addition to the NIRS application. A release procedure developed with WC applied on raw spectra and SIMCA as a second method, which is different from the preferred method of the dNfG, was tested in practice with good results. We conclude that the dNfG has good practicability and that deviations from the preferred methods of the dNfG can also give good differentiation.

Adsorption studies of Cd(II) onto Al 2O 3/Nb 2O 5 mixed oxide dispersed on silica matrix and its on-line preconcentration and determination by flame atomic absorption spectrometry

NASA Astrophysics Data System (ADS)

Mendonça Costa, Lucimara; Ribeiro, Emerson Schwingel; Segatelli, Mariana Gava; do Nascimento, Danielle Raphael; de Oliveira, Fernanda Midori; Tarley, César Ricardo Teixeira

2011-05-01

The present study describes the adsorption characteristic of Cd(II) onto Nb 2O 5/Al 2O 3 mixed oxide dispersed on silica matrix. The characterization of the adsorbent has been carried out by infrared spectroscopy (IR), scanning electronic microscopy (SEM), energy dispersive spectroscopy (EDS), energy dispersive X-ray fluorescence analysis (EDXRF) and specific surface area ( SBET). From batch experiments, adsorption kinetic of Cd(II) was described by a pseudo-second-order kinetic model. The Langmuir linear isotherm fitted to the experimental adsorption isotherm very well, and the maximum adsorption capacity was found to be 17.88 mg g -1. Using the effective material, a method for Cd(II) preconcentration at trace level was developed. The method was based on on-line adsorption of Cd(II) onto SiO 2/Al 2O 3/Nb 2O 5 at pH 8.64, in which the quantitative desorption occurs with 1.0 mol L -1 hydrochloric acid towards FAAS detector. The experimental parameters related to the system were studied by means of multivariate analysis, using 2 4 full factorial design and Doehlert matrix. The effect of SO 42-, Cu 2+, Zn 2+ and Ni 2+ foreign ions showed no interference at 1:100 analyte:interferent proportion. Under the most favorable experimental conditions, the preconcentration system provided a preconcentration factor of 18.4 times, consumption index of 1.08 mL, sample throughput of 14 h -1, concentration efficiency of 4.35 min -1, linear range from 5.0 up to 35.0 μg L -1 and limits of detection and quantification of 0.19 and 0.65 μg L -1 respectively. The feasibility of the proposed method for Cd(II) determination was assessed by analysis of water samples, cigarette sample and certified reference materials TORT-2 (Lobster hepatopancreas) and DOLT-4 (Dogfish liver).

SVM-PB-Pred: SVM based protein block prediction method using sequence profiles and secondary structures.

PubMed

Suresh, V; Parthasarathy, S

2014-01-01

We developed a support vector machine based web server called SVM-PB-Pred, to predict the Protein Block for any given amino acid sequence. The input features of SVM-PB-Pred include i) sequence profiles (PSSM) and ii) actual secondary structures (SS) from DSSP method or predicted secondary structures from NPS@ and GOR4 methods. There were three combined input features PSSM+SS(DSSP), PSSM+SS(NPS@) and PSSM+SS(GOR4) used to test and train the SVM models. Similarly, four datasets RS90, DB433, LI1264 and SP1577 were used to develop the SVM models. These four SVM models developed were tested using three different benchmarking tests namely; (i) self consistency, (ii) seven fold cross validation test and (iii) independent case test. The maximum possible prediction accuracy of ~70% was observed in self consistency test for the SVM models of both LI1264 and SP1577 datasets, where PSSM+SS(DSSP) input features was used to test. The prediction accuracies were reduced to ~53% for PSSM+SS(NPS@) and ~43% for PSSM+SS(GOR4) in independent case test, for the SVM models of above two same datasets. Using our method, it is possible to predict the protein block letters for any query protein sequence with ~53% accuracy, when the SP1577 dataset and predicted secondary structure from NPS@ server were used. The SVM-PB-Pred server can be freely accessed through http://bioinfo.bdu.ac.in/~svmpbpred.

The CE/SE Method: a CFD Framework for the Challenges of the New Millennium

NASA Technical Reports Server (NTRS)

Chang, Sin-Chung; Yu, Sheng-Tao

2001-01-01

The space-time conservation element and solution element (CE/SE) method, which was originated and is continuously being developed at NASA Glenn Research Center, is a high-resolution, genuinely multidimensional and unstructured-mesh compatible numerical method for solving conservation laws. Since its inception in 1991, the CE/SE method has been used to obtain highly accurate numerical solutions for 1D, 2D and 3D flow problems involving shocks, contact discontinuities, acoustic waves, vortices, shock/acoustic waves/vortices interactions, shock/boundary layers interactions and chemical reactions. Without the aid of preconditioning or other special techniques, it has been applied to both steady and unsteady flows with speeds ranging from Mach number = 0.00288 to 10. In addition, the method has unique features that allow for (i) the use of very simple non-reflecting boundary conditions, and (ii) a unified wall boundary treatment for viscous and inviscid flows. The CE/SE method was developed with the conviction that, with a solid foundation in physics, a robust, coherent and accurate numerical framework can be built without involving overly complex mathematics. As a result, the method was constructed using a set of design principles that facilitate simplicity, robustness and accuracy. The most important among them are: (i) enforcing both local and global flux conservation in space and time, with flux evaluation at an interface being an integral part of the solution procedure and requiring no interpolation or extrapolation; (ii) unifying space and time and treating them as a single entity; and (iii) requiring that a numerical scheme be built from a nondissipative core scheme such that the numerical dissipation can be effectively controlled and, as a result, will not overwhelm the physical dissipation. Part I of the workshop will be devoted to a discussion of these principles along with a description of how the ID, 2D and 3D CE/SE schemes are constructed. In Part II, various applications of the CE/SE method, particularly those involving chemical reactions and acoustics, will be presented. The workshop will be concluded with a sketch of the future research directions.

Management of Audio-Visual Media Services. Part II. Practical Management Methods.

ERIC Educational Resources Information Center

Price, Robert V.

1978-01-01

This paper furnishes a framework that allows the local audiovisual administrator to develop a management system necessary for the instructional support of teaching through modern media and educational technology. The structure of this framework rests on organizational patterns which are explained in four categories: complete decentralization,…

Catalytic reduction of pralidoxime in pharmaceuticals by macrocyclic Ni(II) compounds derived from orthophthalaldehyde.

PubMed

Reddy, P Muralidhar; Prasad, Adapa V S S; Rohini, Rondla; Ravinder, Vadde

2008-08-01

Efficient catalytic method for the reduction of pralidoxime to its amine derivative by macrocyclic Ni(II) compounds has been developed. Ten macrocyclic Schiff base Ni(II) compounds were synthesized via non-template synthesis by treating the corresponding macrocycles with nickel chloride in 1:1 ratio. The resulting compounds were characterized by elemental, IR, (1)H NMR, (13)C NMR, mass, electronic spectra, conductance, magnetic, thermal studies and their structures have been proposed. These compounds were used as catalysts for the reduction of pralidoxime to its amino derivative. The reduced pralidoxime was also characterized by spectral analysis and catalytic cycle has been established. The reduced product was determined spectrophotometrically by treating with ninhydrin reagent and the percent yields were found to be in the range of 75.12-82.36%.

ICS-II USA research design and methodology.

PubMed

Rana, H; Andersen, R M; Nakazono, T T; Davidson, P L

1997-05-01

The purpose of the WHO-sponsored International Collaborative Study of Oral Health Outcomes (ICS-II) was to provide policy-markers and researchers with detailed, reliable, and valid data on the oral health situation in their countries or regions, together with comparative data from other dental care delivery systems. ICS-II used a cross-sectional design with no explicit control groups or experimental interventions. A standardized methodology was developed and tested for collecting and analyzing epidemiological, sociocultural, economic, and delivery system data. Respondent information was obtained by household interviews, and clinical examinations were conducted by calibrated oral epidemiologists. Discussed are the sampling design characteristics for the USA research locations, response rates, samples size for interview and oral examination data, weighting procedures, and statistical methods. SUDAAN was used to adjust variance calculations, since complex sampling designs were used.

Construction of a carbon ionic liquid paste electrode based on multi-walled carbon nanotubes-synthesized Schiff base composite for trace electrochemical detection of cadmium.

PubMed

Afkhami, Abbas; Khoshsafar, Hosein; Bagheri, Hasan; Madrakian, Tayyebeh

2014-02-01

A simple, highly sensitive and selective carbon nanocomposite electrode has been developed for the electrochemical trace determination of cadmium. This sensor was designed by incorporation of multi-walled carbon nanotubes (MWCNTs) and a new synthesized Schiff base into the carbon paste ionic liquid electrode (CPE(IL)) which provides remarkably improved sensitivity and selectivity for the electrochemical stripping assay of Cd(II). The detection limit of the method was found to be 0.08 μg L(-1) (S/N=3) that is lower than the maximum contaminant level of Cd(II) allowed by the Environmental Protection Agency (EPA) in standard drinking waters. The proposed electrode exhibits good applicability for monitoring Cd(II) in various real samples. © 2013.

Spectrophotometric determination of some anti-tussive and anti-spasmodic drugs through ion-pair complex formation with thiocyanate and cobalt(II) or molybdenum(V)

NASA Astrophysics Data System (ADS)

El-Shiekh, Ragaa; Zahran, Faten; El-Fetouh Gouda, Ayman Abou

2007-04-01

Two rapid, simple and sensitive extractive specrophotometric methods has been developed for the determination of anti-tussive drugs, e.g., dextromethorphan hydrobromide (DEX) and pipazethate hydrochloride (PiCl) and anti-spasmodic drugs, e.g., drotaverine hydrochloride (DvCl) and trimebutine maleate (TM) in bulk and in their pharmaceutical formulations. The proposed methods depend upon the reaction of cobalt(II)-thiocyanate (method A) and molybdenum(V)-thiocyanate ions (method B) with the cited drugs to form stable ion-pair complexes which extractable with an n-butnol-dichloromethane solvent mixture (3.5:6.5) and methylene chloride for methods A and B, respectively. The blue and orange red color complexes are determined either colorimetrically at λmax 625 nm (using method A) and 467 or 470 nm for (DEX and PiCl) or (DvCl and TM), respectively (using method B). The concentration range is 20-400 and 2.5-50 μg mL -1 for methods A and B, respectively. The proposed method was successfully applied for the determination of the studied drugs in pure and in pharmaceutical formulations applying the standard additions technique and the results obtained in good agreement well with those obtained by the official method.

Controlled Fabrication of Silk Protein Sericin Mediated Hierarchical Hybrid Flowers and Their Excellent Adsorption Capability of Heavy Metal Ions of Pb(II), Cd(II) and Hg(II).

PubMed

Koley, Pradyot; Sakurai, Makoto; Aono, Masakazu

2016-01-27

Fabrication of protein-inorganic hybrid materials of innumerable hierarchical patterns plays a major role in the development of multifunctional advanced materials with their improved features in synergistic way. However, effective fabrication and applications of the hybrid structures is limited due to the difficulty in control and production cost. Here, we report the controlled fabrication of complex hybrid flowers with hierarchical porosity through a green and facile coprecipitation method by using industrial waste natural silk protein sericin. The large surface areas and porosity of the microsize hybrid flowers enable water purification through adsorption of different heavy metal ions. The high adsorption capacity depends on their morphology, which is changed largely by sericin concentration in their fabrication. Superior adsorption and greater selectivity of the Pb(II) ions have been confirmed by the characteristic growth of needle-shaped nanowires on the hierarchical surface of the hybrid flowers. These hybrid flowers show excellent thermal stability even after complete evaporation of the protein molecules, significantly increasing the porosity of the flower petals. A simple, cost-effective and environmental friendly fabrication method of the porous flowers will lead to a new solution to water pollution required in the modern industrial society.

Ligandless surfactant mediated solid phase extraction combined with Fe₃O₄ nano-particle for the preconcentration and determination of cadmium and lead in water and soil samples followed by flame atomic absorption spectrometry: multivariate strategy.

PubMed

Jalbani, N; Soylak, M

2014-04-01

In the present study, a microextraction technique combining Fe3O4 nano-particle with surfactant mediated solid phase extraction ((SM-SPE)) was successfully developed for the preconcentration/separation of Cd(II) and Pb(II) in water and soil samples. The analytes were determined by flame atomic absorption spectrometry (FAAS). The effective variables such as the amount of adsorbent (NPs), the pH, concentration of non-ionic (TX-114) and centrifugation time (min) were investigated by Plackett-Burman (PBD) design. The important variables were further optimized by central composite design (CCD). Under the optimized conditions, the detection limits (LODs) of Cd(II) and Pb(II) were 0.15 and 0.74 µg/L, respectively. The validation of the proposed procedure was checked by the analysis of certified reference materials of TMDA 53.3 fortified water and GBW07425 soil. The method was successfully applied for the determination of Cd(II) and Pb(II) in water and soil samples. Copyright © 2014 Elsevier Inc. All rights reserved.

Spectrophotometric Determination of Iron(II) and Cobalt(II) by Direct, Derivative, and Simultaneous Methods Using 2-Hydroxy-1-Naphthaldehyde-p-Hydroxybenzoichydrazone

PubMed Central

Devi, V. S. Anusuya; Reddy, V. Krishna

2012-01-01

Optimized and validated spectrophotometric methods have been proposed for the determination of iron and cobalt individually and simultaneously. 2-hydroxy-1-naphthaldehyde-p-hydroxybenzoichydrazone (HNAHBH) reacts with iron(II) and cobalt(II) to form reddish-brown and yellow-coloured [Fe(II)-HNAHBH] and [Co(II)-HNAHBH] complexes, respectively. The maximum absorbance of these complexes was found at 405 nm and 425 nm, respectively. For [Fe(II)-HNAHBH], Beer's law is obeyed over the concentration range of 0.055–1.373 μg mL−1 with a detection limit of 0.095 μg mL−1 and molar absorptivity ɛ, 5.6 × 104 L mol−1 cm−1. [Co(II)-HNAHBH] complex obeys Beer's law in 0.118–3.534 μg mL−1 range with a detection limit of 0.04 μg mL−1 and molar absorptivity, ɛ of 2.3 × 104 L mol−1 cm−1. Highly sensitive and selective first-, second- and third-order derivative methods are described for the determination of iron and cobalt. A simultaneous second-order derivative spectrophotometric method is proposed for the determination of these metals. All the proposed methods are successfully employed in the analysis of various biological, water, and alloy samples for the determination of iron and cobalt content. PMID:22505925

Analytical method development and validation of spectrofluorimetric and spectrophotometric determination of some antimicrobial drugs in their pharmaceuticals.

PubMed

Ibrahim, F; Wahba, M E K; Magdy, G

2018-01-05

In this study, three novel, sensitive, simple and validated spectrophotometric and spectrofluorimetric methods have been proposed for estimation of some important antimicrobial drugs. The first two methods have been proposed for estimation of two important third-generation cephalosporin antibiotics namely, cefixime and cefdinir. Both methods were based on condensation of the primary amino group of the studied drugs with acetyl acetone and formaldehyde in acidic medium. The resulting products were measured by spectrophotometric (Method I) and spectrofluorimetric (Method II) tools. Regarding method I, the absorbance was measured at 315nm and 403nm with linearity ranges of 5.0-140.0 and 10.0-100.0μg/mL for cefixime and cefdinir, respectively. Meanwhile in method II, the produced fluorophore was measured at λ em 488nm or 491nm after excitation at λ ex 410nm with linearity ranges of 0.20-10.0 and 0.20-36.0μg/mL for cefixime and cefdinir, respectively. On the other hand, method III was devoted to estimate nifuroxazide spectrofluorimetrically depending on formation of highly fluorescent product upon reduction of the studied drug with Zinc powder in acidic medium. Measurement of the fluorescent product was carried out at λ em 335nm following excitation at λ ex 255nm with linearity range of 0.05 to 1.6μg/mL. The developed methods were subjected to detailed validation procedure, moreover they were used for the estimation of the concerned drugs in their pharmaceuticals. It was found that there is a good agreement between the obtained results and those obtained by the reported methods. Copyright © 2017 Elsevier B.V. All rights reserved.

Analytical method development and validation of spectrofluorimetric and spectrophotometric determination of some antimicrobial drugs in their pharmaceuticals

NASA Astrophysics Data System (ADS)

Ibrahim, F.; Wahba, M. E. K.; Magdy, G.

2018-01-01

In this study, three novel, sensitive, simple and validated spectrophotometric and spectrofluorimetric methods have been proposed for estimation of some important antimicrobial drugs. The first two methods have been proposed for estimation of two important third-generation cephalosporin antibiotics namely, cefixime and cefdinir. Both methods were based on condensation of the primary amino group of the studied drugs with acetyl acetone and formaldehyde in acidic medium. The resulting products were measured by spectrophotometric (Method I) and spectrofluorimetric (Method II) tools. Regarding method I, the absorbance was measured at 315 nm and 403 nm with linearity ranges of 5.0-140.0 and 10.0-100.0 μg/mL for cefixime and cefdinir, respectively. Meanwhile in method II, the produced fluorophore was measured at λem 488 nm or 491 nm after excitation at λex 410 nm with linearity ranges of 0.20-10.0 and 0.20-36.0 μg/mL for cefixime and cefdinir, respectively. On the other hand, method III was devoted to estimate nifuroxazide spectrofluorimetrically depending on formation of highly fluorescent product upon reduction of the studied drug with Zinc powder in acidic medium. Measurement of the fluorescent product was carried out at λem 335 nm following excitation at λex 255 nm with linearity range of 0.05 to 1.6 μg/mL. The developed methods were subjected to detailed validation procedure, moreover they were used for the estimation of the concerned drugs in their pharmaceuticals. It was found that there is a good agreement between the obtained results and those obtained by the reported methods.

Construction of silica aerogel radiator system for Belle II RICH Counter

NASA Astrophysics Data System (ADS)

Adachi, I.; Dolenec, R.; Hataya, K.; Iori, S.; Iwata, S.; Kakuno, H.; Kataura, R.; Kawai, H.; Kindo, H.; Kobayashi, T.; Korpar, S.; Križan, P.; Kumita, T.; Mrvar, M.; Nishida, S.; Ogawa, K.; Ogawa, S.; Pestotnik, R.; Šantelj, L.; Sumiyoshi, T.; Tabata, M.; Yonenaga, M.; Yusa, Y.

2017-12-01

We have developed a RICH counter as a new forward particle identification device for the Belle II experiment. As a Cherenkov radiator in this counter, a dual aerogel layer combination consisting of two refractive indicies, n=1.045 and 1.055, is employed. Mass production of these aerogel tiles has been done during 2013-2014 with new method improved by Chiba group. Optical qualities for them have been examined. The refractive indices of the obtained tiles were found to be in good agreement with our expectations, and the transparencies were high enough to be used for the RICH radiator.

Evidence for Alkene cis-Aminocupration, an Aminooxygenation Case Study: Kinetics, EPR Spectroscopy, and DFT Calculations

PubMed Central

Paderes, Monissa C.; Belding, Lee; Fanovic, Branden; Dudding, Travis; Keister, Jerome B.

2012-01-01

Alkene difunctionalization reactions are important in organic synthesis. We have recently shown that copper(II) complexes can promote and catalyze intramolecular alkene aminooxygenation, carboamination, and diamination reactions. In this contribution, we report a combined experimental and theoretical examination of the mechanism of the copper(II)-promoted olefin aminooxygenation reaction. Kinetics experiments revealed a mechanistic pathway involving an equilibrium reaction between a copper(II) carboxylate complex and the γ-alkenyl sulfonamide substrate and a rate-limiting intramolecular cis-addition of N–Cu across the olefin. Kinetic isotope effect studies support that the cis-aminocupration is the rate-determining step. UV/Vis spectra support a role for the base in the break-up of copper(II) carboxylate dimer to monomeric species. Electron paramagnetic resonance (EPR) spectra provide evidence for a kinetically competent N–Cu intermediate with a CuII oxidation state. Due to the highly similar stereochemical and reactivity trends among the CuII-promoted and catalyzed alkene difunctionalization reactions we have developed, the cis-aminocupration mechanism can reasonably be generalized across the reaction class. The methods and findings disclosed in this report should also prove valuable to the mechanism analysis and optimization of other copper(-II) carboxylate promoted reactions, especially those that take place in aprotic organic solvents. PMID:22237868

A Simple and Fast Method Based on New Magnetic Ion Imprinted Polymer as a Highly Selective Sorbent for Preconcentration and Determination of Cadmium in Environmental Samples

PubMed Central

PANJALI, Zahra; ASGHARINEZHAD, Ali Akbar; EBRAHIMZADEH, Homeira; JALILIAN, Niloofar; YARAHMADI, Rasoul; SHAHTAHERI, Seyed Jamaleddin

2016-01-01

Background: The analysis of heavy metals at trace level is one of the main toxicologists concern, due to their vital rules in human`s life. Cadmium is one of these toxic heavy metals, which released to the environment from various industries. Methods: In order to determine Cd (II) ions in various matrices magnetic ion-imprinted polymer (IIP) method has been developed and applied. This nano-sorbent has been synthesized by coating an IIP compound on Fe3O4 nanoparticles core to achieve highest surface area. This polymer has been used to evaluate Cd (II) levels in food, river, and wastewater in Tehran, Iran. Results: Fe3O4@Cd-IIP was stable up to 300 °C. The various factors such as sample pH (optimized as 7), elution/sorption time (5 min), eluent amount (4 mL HCL), and its concentration (2 mol L−1) were optimized. Analysis instrument in all steps was Flame Atomic Abortion Spectrophotometer (FAAS). In this study, the detection limit was determined down to 0.6 μg L−1. Conclusion: This method was applied successfully for the preconcentration and determination of Cd (II) ions in environmental samples obtained from rivers, various foods and wastewater. In addition, the accuracy of the method was confirmed by analyzing a certified reference material (Seronorm LOT NO2525) and spiked real samples. PMID:27928531

Clinical practice guidelines and consensus statements in oncology--an assessment of their methodological quality.

PubMed

Jacobs, Carmel; Graham, Ian D; Makarski, Julie; Chassé, Michaël; Fergusson, Dean; Hutton, Brian; Clemons, Mark

2014-01-01

Consensus statements and clinical practice guidelines are widely available for enhancing the care of cancer patients. Despite subtle differences in their definition and purpose, these terms are often used interchangeably. We systematically assessed the methodological quality of consensus statements and clinical practice guidelines published in three commonly read, geographically diverse, cancer-specific journals. Methods Consensus statements and clinical practice guidelines published between January 2005 and September 2013 in Current Oncology, European Journal of Cancer and Journal of Clinical Oncology were evaluated. Each publication was assessed using the Appraisal of Guidelines for Research and Evaluation II (AGREE II) rigour of development and editorial independence domains. For assessment of transparency of document development, 7 additional items were taken from the Institute of Medicine's standards for practice guidelines and the Journal of Clinical Oncology guidelines for authors of guidance documents. Consensus statements and clinical practice guidelines published between January 2005 and September 2013 in Current Oncology, European Journal of Cancer and Journal of Clinical Oncology were evaluated. Each publication was assessed using the Appraisal of Guidelines for Research and Evaluation II (AGREE II) rigour of development and editorial independence domains. For assessment of transparency of document development, 7 additional items were taken from the Institute of Medicine's standards for practice guidelines and the Journal of Clinical Oncology guidelines for authors of guidance documents. Thirty-four consensus statements and 67 clinical practice guidelines were evaluated. The rigour of development score for consensus statements over the three journals was 32% lower than that of clinical practice guidelines. The editorial independence score was 15% lower for consensus statements than clinical practice guidelines. One journal scored consistently lower than the others over both domains. No journals adhered to all the items related to the transparency of document development. One journal's consensus statements endorsed a product made by the sponsoring pharmaceutical company in 64% of cases. Guidance documents are an essential part of oncology care and should be subjected to a rigorous and validated development process. Consensus statements had lower methodological quality than clinical practice guidelines using AGREE II. At a minimum, journals should ensure that that all consensus statements and clinical practice guidelines adhere to AGREE II criteria. Journals should consider explicitly requiring guidelines to declare pharmaceutical company sponsorship and to identify the sponsor's product to enhance transparency.

Space Shuttle main engine product improvement

NASA Technical Reports Server (NTRS)

Lucci, A. D.; Klatt, F. P.

1985-01-01

The current design of the Space Shuttle Main Engine has passed 11 certification cycles, amassed approximately a quarter million seconds of engine test time in 1200 tests and successfully launched the Space Shuttle 17 times of 51 engine launches through May 1985. Building on this extensive background, two development programs are underway at Rocketdyne to improve the flow of hot gas through the powerhead and evaluate the changes to increase the performance margins in the engine. These two programs, called Phase II+ and Technology Test Bed Precursor program are described. Phase II+ develops a two-tube hot-gas manifold that improves the component environment. The Precursor program will evaluate a larger throat main combustion chamber, conduct combustion stability testing of a baffleless main injector, fabricate an experimental weld-free heat exchanger tube, fabricate and test a high pressure oxidizer turbopump with an improved inlet, and develop and test methods for reducing temperature transients at start and shutdown.

Introduction to electron crystallography.

PubMed

Kühlbrandt, Werner

2013-01-01

From the earliest work on regular arrays in negative stain, electron crystallography has contributed greatly to our understanding of the structure and function of biological macromolecules. The development of electron cryo-microscopy (cryo-EM) then lead to the first groundbreaking atomic models of the membrane proteins bacteriorhodopsin and light harvesting complex II within lipid bilayers. Key contributions towards cryo-EM and electron crystallography methods included specimen preparation and vitrification, liquid-helium cooling, data collection, and image processing. These methods are now applied almost routinely to both membrane and soluble proteins. Here we outline the advances and the breakthroughs that paved the way towards high-resolution structures by electron crystallography, both in terms of methods development and biological milestones.

Geriatric Core Competencies for Family Medicine Curriculum and Enhanced Skills: Care of Elderly

PubMed Central

Charles, Lesley; Triscott, Jean A.C.; Dobbs, Bonnie M.; McKay, Rhianne

2014-01-01

Background There is a growing mandate for Family Medicine residency programs to directly assess residents’ clinical competence in Care of the Elderly (COE). The objectives of this paper are to describe the development and implementation of incremental core competencies for Postgraduate Year (PGY)-I Integrated Geriatrics Family Medicine, PGY-II Geriatrics Rotation Family Medicine, and PGY-III Enhanced Skills COE for COE Diploma residents at a Canadian University. Methods Iterative expert panel process for the development of the core competencies, with a pre-defined process for implementation of the core competencies. Results Eighty-five core competencies were selected overall by the Working Group, with 57 core competencies selected for the PGY-I/II Family Medicine residents and an additional 28 selected for the PGY-III COE residents. The core competencies follow the CanMEDS Family Medicine roles. Both sets of core competencies are based on consensus. Conclusions Due to demographic changes, it is essential that Family Physicians have the required skills and knowledge to care for the frail elderly. The core competencies described were developed for PGY-I/II Family Medicine residents and PGY-III Enhanced Skills COE, with a focus on the development of geriatric expertise for those patients that would most benefit. PMID:24883163

Fracture characterization of human cortical bone under mode II loading using the end-notched flexure test.

PubMed

Silva, F G A; de Moura, M F S F; Dourado, N; Xavier, J; Pereira, F A M; Morais, J J L; Dias, M I R; Lourenço, P J; Judas, F M

2017-08-01

Fracture characterization of human cortical bone under mode II loading was analyzed using a miniaturized version of the end-notched flexure test. A data reduction scheme based on crack equivalent concept was employed to overcome uncertainties on crack length monitoring during the test. The crack tip shear displacement was experimentally measured using digital image correlation technique to determine the cohesive law that mimics bone fracture behavior under mode II loading. The developed procedure was validated by finite element analysis using cohesive zone modeling considering a trapezoidal with bilinear softening relationship. Experimental load-displacement curves, resistance curves and crack tip shear displacement versus applied displacement were used to validate the numerical procedure. The excellent agreement observed between the numerical and experimental results reveals the appropriateness of the proposed test and procedure to characterize human cortical bone fracture under mode II loading. The proposed methodology can be viewed as a novel valuable tool to be used in parametric and methodical clinical studies regarding features (e.g., age, diseases, drugs) influencing bone shear fracture under mode II loading.

Using laser capture microdissection to study fiber specific signaling in locomotor muscle in COPD: A pilot study.

PubMed

Mohan, Divya; Lewis, Amy; Patel, Mehul S; Curtis, Katrina J; Lee, Jen Y; Hopkinson, Nicholas S; Wilkinson, Ian B; Kemp, Paul R; Polkey, Michael I

2017-06-01

Quadriceps dysfunction is important in chronic obstructive pulmonary disease (COPD), with an associated increased proportion of type II fibers. Investigation of protein synthesis and degradation has yielded conflicting results, possibly due to study of whole biopsy samples, whereas signaling may be fiber-specific. Our objective was to develop a method for fiber-specific gene expression analysis. 12 COPD and 6 healthy subjects underwent quadriceps biopsy. Cryosections were immunostained for type II fibers, which were separated using laser capture microdissection (LCM). Whole muscle and different fiber populations were subject to quantitative polymerase chain reaction. Levels of muscle-RING-finger-protein-1 and Atrogin-1 were lower in type II fibers of COPD versus healthy subjects (P = 0.02 and P = 0.03, respectively), but differences were not apparent in whole muscle or type I fibers. We describe a novel method for studying fiber-specific gene expression in optimum cutting temperature compound-embedded muscle specimens. LCM offers a more sensitive way to identify molecular changes in COPD muscle. Muscle Nerve 55: 902-912, 2017. © 2016 Wiley Periodicals, Inc.

Spectrophotometric determination of dopamine hydrochloride in pharmaceutical, banana, urine and serum samples by potassium ferricyanide-Fe(III).

PubMed

Guo, Li; Zhang, Yan; Li, Quanmin

2009-12-01

In the present work, we developed a simple, sensitive and inexpensive method to determine dopamine hydrochloride using potassium ferricyanide-Fe(III) by spectrophotometry. The results show that Fe(III) is deoxidized to Fe(II) by dopamine hydrochloride at pH 4.0, and then Fe(II) reacts with potassium ferricyanide to form a soluble prussian blue (KFe(III)[Fe(II)(CN)6]). The absorbance of this product was monitored over time using a spectrophotometer at an absorption maximum of 735 nm, and the amount of dopamine hydrochloride could be calculated based on the absorbance. A good linear relationship of the concentration of dopamine hydrochloride versus absorbance was observed, and a linear regression equation of A = 0.022 + 0.16921C (microg mL(-1)) was obtained. Moreover, the apparent molar absorption coefficient for the indirect determination of dopamine hydrochloride was 3.2 x 10(4) L mol(-1) cm(-1). This described method has been used to determine dopamine hydrochloride in pharmaceutical, banana, urine and serum samples with satisfactory results.

[Study on the analysis of organogermanium compounds by ion chromatography].

PubMed

Chen, Q; Mou, S; Hou, X; Ni, Z

1997-05-01

A new high performance ion exchange chromatographic method for separation and determination of three organogermanium compounds beta-carboxyethylgermanium sesquioxide (I), beta-(alpha-methyl) carboxyethylgermanium sesquioxide (II) and di-(beta-carboxyethyl) germanium hydroxide (III) has been developed. A Dionex DX-300 Ion Chromatograph equipped with a Dionex PED-II pulsed electrochemical detector (conductivity mode), a Dionex AMMS-1 anion micromembrane suppressor, and a Dionex ACI advanced computer interface coupled with AI-450 chromatographic software was employed. The separation was achieved by using a Dionex IonPac AS4A-SC column as analytical column, sodium tetraborate solution as eluent, and sulfuric acid solution as regenerant. For reducing run time, a gradient program was chosen. The detection limits (S/N = 3, expressed as germanium) for the three compounds were 0.038mg/L (I), 0.035mg/L (II) and 0.025mg/L (III), respectively. The method has been applied to the analysis of two tonic oral drinks, and the average recoveries for the three compounds ranged from 95%-101%. The results obtained were in agreement with those of hydride generation atomic fluorescence spectrometry (HG-AFS).

Development of a Method to Determine the Audiogram of the Guinea Pig for Threshold Shift Studies,

DTIC Science & Technology

1984-01-01

AD-A139 717 DEVELOPENI OF A MEHO 10O DEUUUINE tHE AU0IOOGAB Of II THE GUINEA PIG FP0.6 I ARM AEOICAL RESEARCH LAO FORT RUICKER AL. C COMPEIIAIOAE It...tS4 USAARL REPORT NO. 84 - 4 RESU DEVELOPMENT OF A METHOD TO DETERMINE THE AUDIOGRAM OF THE GUINEA PIG FOR THRESHOLD SHIFT STUDIES By Carlos Comperatore...Determine the Audiogram of the Guinea Pig for Threshold Shift Studies G. PERFORMING ORo. REPORT MummaR 7. AUTHOR(e) S. CONTRACT OR GRANT NUMSERa) Carlos

Method of manufacturing semiconductor having group II-group VI compounds doped with nitrogen

DOEpatents

Compaan, Alvin D.; Price, Kent J.; Ma, Xianda; Makhratchev, Konstantin

2005-02-08

A method of making a semiconductor comprises depositing a group II-group VI compound onto a substrate in the presence of nitrogen using sputtering to produce a nitrogen-doped semiconductor. This method can be used for making a photovoltaic cell using sputtering to apply a back contact layer of group II-group VI compound to a substrate in the presence of nitrogen, the back coating layer being doped with nitrogen. A semiconductor comprising a group II-group VI compound doped with nitrogen, and a photovoltaic cell comprising a substrate on which is deposited a layer of a group II-group VI compound doped with nitrogen, are also included.

Voltammetric determination of tartaric acid in wines by electrocatalytic oxidation on a cobalt(II)-phthalocyanine-modified electrode associated with multiway calibration.

PubMed

Lourenço, Anabel S; Nascimento, Raphael F; Silva, Amanda C; Ribeiro, Williame F; Araujo, Mario C U; Oliveira, Severino C B; Nascimento, Valberes B

2018-05-30

The electrocatalytic oxidation of tartaric acid on a carbon paste electrode modified with cobalt (II)-phthalocyanine was demonstrated and applied to the development of a highly sensitive, simple, fast and inexpensive voltammetric sensor to determine tartaric acid. The electrochemical behavior of the modified electrode was investigated by cyclic and square wave voltammetry, and the effect of experimental variables, such as dispersion and loading of cobalt (II)-phthalocyanine, together with optimum conditions for sensing the analyte by square wave voltammetry were assessed. In addition, the absence of a significant memory effect combined with the ease of electrode preparation led to the development of a sensitive and direct method to determine tartaric acid in wines. Interferences from other low molecular weight organic acids commonly present in wines were circumvented by using a multiway calibration technique, successfully obtaining the second order advantage by modeling voltammetric data with unfolded partial least square with residual bilinearization (U-PLS/RBL). A linear response range between 10 and 100 μmol L -1 (r = 0.9991), a relative prediction error of 4.55% and a recovery range from 96.41 to 102.43% were obtained. The proposed method is non-laborious, since it does not use sample pretreatment such as filtration, extraction, pre-concentration or cleanup procedures. Copyright © 2018 Elsevier B.V. All rights reserved.

A feasibility study of prepubertal and over mature aged local goat in relation to results of In Vitro growth culture to obtain additional M-II oocyte resources

NASA Astrophysics Data System (ADS)

Ciptadi, Gatot; Ihsan, M. Nur; Rahayu, Sri; Widjaja, D. H. K.; Mudawamah, Mudawamah

2017-11-01

The aims of this research are to study the potential source of mature (M-II) oocytes of domestic animals using follicles isolated from prepubertal and over mature aged Indonesian local goats, resulting from an in vitro growth (IVG) method. This method of IVG could provide a new source of M-II oocytes for embryo production. In Indonesia, a very limited number of a good quality oocytes are available for research purposes, as there is a limited number of reproductive females slaughtered, which is dominated by prepubertal and old mature aged animals. IVG culture systems could be improved as an alternative method to provide a new source of a good quality oocytes for in vitro maturation of M-II oocytes. From a number of prepubertal and mature aged goats slaughtered in a local abattoir, the small oocytes in the preantral follicles were cultured in vitro to normal oocyte growth. The methods used in this research are experimental. Follicles were isolated, cultured in vitro for 14 days individually using a sticky medium containing 4% (w/v) polyvinylpyrrolidone in TCM 199 10% Fetal Bovine Serum supplemented with Follicle Stimulating Hormone, which was then evaluated for their follicle development and oocyte quality. The research results showed that a minimum follicle size and oocyte diameter is needed (>100 um) for early evaluation of maturation to be achieved, meanwhile oocytes recovered from IVG after being cultured in vitro for maturation resulted in a very low rate of maturation. However, in the future, IVG of the preantral follicles of Indonesian local goat could be considered as an alternative source of oocytes for both research purposes and embryo production in vitro.

Simultaneous quantification of flavonoids in blood plasma by a high-performance liquid chromatography method after oral administration of Blumea balsamifera leaf extracts in rats.

PubMed

Nessa, Fazilatun; Ismail, Zhari; Mohamed, Nornisah; Karupiah, Sundram

2013-03-01

The leaves of Blumea balsamifera are used as a folk medicine in kidney stone diseases in South-East Asia. Phytochemical investigation revealed leaves contained a number of flavonoids. In view of these, the present work was aimed to quantify and preliminary pharmacokinetic investigation of five flavonoids viz. dihydroquercetin-7,4¢-dimethyl ether (I), dihydroquercetin-4¢-methyl ether (II), 5,7,3¢,5¢-tetrahydroxyflavanone (III), blumeatin (IV) and quercetin (V) in rat plasma following oral administration (0.5g/Kg) of B. balsamifera leaf extract in rats. Quantification was achieved by using a validated, reproducible high-performance liquid chromatographic method. The mean recoveries of I, II, III, IV and V were 90.6, 93.4, 93.5, 91.2 and 90.3% respectively. The limit of quantification was 25 ng/mL for I and IV, 10 ng/mL for II and III and 100 ng/mL for V respectively. The within day and day-to-day precision for all the compounds were < 10%. The validated HPLC method herein was applied for pharmacokinetic studies and the main pharmacokinetic parameters were: t1/2 (hr) 5.8, 4.3, 2.9, 5.7 and 7.3, Cmax (ng/mL) 594.9, 1542.9 1659.9, 208.9 and 3040.4; Tmax (hr) 4.7, 1.0, 1.0, 3.5 and 2.3; AUC0-oo (ng hr/mL) 5040, 5893, 9260, 1064 and 27233 for I, II, III, IV and V respectively. The developed method was suitable for pharmacokinetic studies and this preliminary study also revealed significant absorption after oral dosing in rats.

The expanding photosphere method applied to SN 1992am AT cz = 14 600 km/s

NASA Technical Reports Server (NTRS)

Schmidt, Brian P.; Kirshner, Robert P.; Eastman, Ronald G.; Hamuy, Mario; Phillips, Mark M.; Suntzeff, Nicholas B.; Maza, Jose; Filippenko, Alexei V.; Ho, Luis C.; Matheson, Thomas

1994-01-01

We present photometry and spectroscopy of Supernova (SN) 1992am for five months following its discovery by the Calan Cerro-Tololo Inter-American Observatory (CTIO) SN search. These data show SN 1992am to be type II-P, displaying hydrogen in its spectrum and the typical shoulder in its light curve. The photometric data and the distance from our own analysis are used to construct the supernova's bolometric light curve. Using the bolometric light curve, we estimate SN 1992am ejected approximately 0.30 solar mass of Ni-56, an amount four times larger than that of other well studied SNe II. SN 1992am's; host galaxy lies at a redshift of cz = 14 600 km s(exp -1), making it one of the most distant SNe II discovered, and an important application of the Expanding Photsphere Method. Since z = 0.05 is large enough for redshift-dependent effects to matter, we develop the technique to derive luminosity distances with the Expanding Photosphere Method at any redshift, and apply this method to SN 1992am. The derived distance, D = 180(sub -25) (sup +30) Mpc, is independent of all other rungs in the extragalactic distance ladder. The redshift of SN 1992am's host galaxy is sufficiently large that uncertainties due to perturbations in the smooth Hubble flow should be smaller than 10%. The Hubble ratio derived from the distance and redshift of this single object is H(sub 0) = 81(sub -15) (sup +17) km s(exp -1) Mpc(exp -1). In the future, with more of these distant objects, we hope to establish an independent and statistically robust estimate of H(sub 0) based solely on type II supernovae.

Establishment of a simple and quantitative immunospot assay for detecting anti-type II collagen antibody using an infrared fluorescence imaging system (IFIS).

PubMed

Ota, Shusuke; Kanazawa, Satoshi; Kobayashi, Masaaki; Otsuka, Takanobu; Okamoto, Takashi

2005-04-01

Antibodies to type II collagen (col II) have been detected in patients with rheumatoid arthritis and in animal models of collagen induced arthritis. Here, we describe a novel method to detect anti-col II antibodies using an immunospot assay with an infrared fluorescence imaging system. This method showed very high sensitivity and specificity, and was simple, with low background levels. It also showed higher reproducibility and linearity, with a dynamic range of approximately 500-fold, than the conventional immunospot assay with enhanced chemiluminescence detection. Using this method we were able to demonstrate the antibody affinity maturation process in mice immunized with col II. In these immunized mice, although cross-reactive antibodies reacting with other collagen species were detected in earlier stages of immunization, the titers of cross-reactive antibodies rapidly diminished after the antigen boost, concomitantly with the elevation of the anti-col II antibody. The method and its possible applications are discussed.

Speciation analysis of Mn(II)/Mn(VII) using Fe3O4@ionic liquids-β-cyclodextrin polymer magnetic solid phase extraction coupled with ICP-OES.

PubMed

Chen, Songqing; Qin, Xingxiu; Gu, Weixi; Zhu, Xiashi

2016-12-01

Ionic liquids-β-cyclodextrin polymer (ILs-β-CDCP) was attached on Fe 3 O 4 nanoparticles to prepare magnetic solid phase extraction agent (Fe 3 O 4 @ILs-β-CDCP). The properties and morphology of Fe 3 O 4 @ILs-β-CDCP were characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction(XRD), size distribution and magnetic analysis. A new method of magnetic solid phase extraction (MSPE) coupled to ICP-OES for the speciation of Mn(II)/Mn(VII) in water samples was established. The results showed that Mn(VII) and total manganese [Mn(II)+Mn(VII)] were quantitatively extracted after adjusting aqueous sample solution to pH 6.0 and 10.0, respectively. Mn(II) was calculated by subtraction of Mn(VII) from total manganese. Fe 3 O 4 @ILs-β-CDCP showed a higher adsorption capacity toward Mn(II) and Mn(VII). Several factors, such as the pH value, extraction temperature and sample volume, were optimized to achieve the best extraction efficiency. Moreover, the adsorption ability of Fe 3 O 4 @ILs-β-CDCP would not be significantly lower after reusing of 10 times. The accuracy of the developed method was confirmed by analyzing certified reference materials (GSB 07-1189-2000), and by spiking spring water, city water and lake water samples. Copyright © 2016 Elsevier B.V. All rights reserved.

A Comparison of a Machine Learning Model with EuroSCORE II in Predicting Mortality after Elective Cardiac Surgery: A Decision Curve Analysis.

PubMed

Allyn, Jérôme; Allou, Nicolas; Augustin, Pascal; Philip, Ivan; Martinet, Olivier; Belghiti, Myriem; Provenchere, Sophie; Montravers, Philippe; Ferdynus, Cyril

2017-01-01

The benefits of cardiac surgery are sometimes difficult to predict and the decision to operate on a given individual is complex. Machine Learning and Decision Curve Analysis (DCA) are recent methods developed to create and evaluate prediction models. We conducted a retrospective cohort study using a prospective collected database from December 2005 to December 2012, from a cardiac surgical center at University Hospital. The different models of prediction of mortality in-hospital after elective cardiac surgery, including EuroSCORE II, a logistic regression model and a machine learning model, were compared by ROC and DCA. Of the 6,520 patients having elective cardiac surgery with cardiopulmonary bypass, 6.3% died. Mean age was 63.4 years old (standard deviation 14.4), and mean EuroSCORE II was 3.7 (4.8) %. The area under ROC curve (IC95%) for the machine learning model (0.795 (0.755-0.834)) was significantly higher than EuroSCORE II or the logistic regression model (respectively, 0.737 (0.691-0.783) and 0.742 (0.698-0.785), p < 0.0001). Decision Curve Analysis showed that the machine learning model, in this monocentric study, has a greater benefit whatever the probability threshold. According to ROC and DCA, machine learning model is more accurate in predicting mortality after elective cardiac surgery than EuroSCORE II. These results confirm the use of machine learning methods in the field of medical prediction.

Multisurface modeling of Ni bioavailability to wheat (Triticum aestivum L.) in various soils.

PubMed

Zhao, Xiaopeng; Jiang, Yang; Gu, Xueyuan; Gu, Cheng; Taylor, J Anita; Evans, Les J

2018-07-01

Continual efforts have been made to determine a simple and universal method of estimating heavy metal phytoavailability in terrestrial systems. In the present study, a mechanism-based multi-surface model (MSM) was developed to predict the partition of Ni(II) in soil-solution phases and its bioaccumulation in wheat (Triticum aestivum L.) in 19 Chinese soils with a wide range of soil properties. MSM successfully predicted the Ni(II) dissolution in 0.01 M CaCl 2 extracting solution (R 2  = 0.875). The two-site model for clay fraction improved the prediction, particularly for alkaline soils, because of the additional consideration of edge sites. More crucially, the calculated dissolved Ni(II) was highly correlated with the metal accumulation in wheat (R 2  = 0.820 for roots and 0.817 for shoots). The correlation coefficients for the MSM and various chemical extraction methods have the following order: soil pore water > MSM ≈ diffuse gradient technique (DGT) > soil total Ni > 0.43 M HNO 3  > 0.01 M CaCl 2 . The results suggested that the dissolved Ni(II) calculated using MSM can serve as an effective indicator of the bioavailability of Ni(II) in various soils; hence, MSM can be used as an supplement for metal risk prediction and assessment besides chemical extraction techniques. Copyright © 2018 Elsevier Ltd. All rights reserved.

A systematic review and appraisal of the quality of practice guidelines for the management of Neisseria gonorrhoeae infections.

PubMed

Dickson, Catherine; Arnason, Trevor; Friedman, Dara Spatz; Metz, Gila; Grimshaw, Jeremy M

2017-11-01

Clinical guidelines help ensure consistent care informed by current evidence. As shifts in antimicrobial resistance continue to influence first-line treatment, up-to-date guidelines are important for preventing treatment failure. A guideline's development process will influence its recommendations and users' trust. To assess the quality of current gonorrhoea guidelines' development processes. Multiple databases. Original and current English-language guidelines targeting health professionals and containing treatment recommendations for uncomplicated gonorrhoea in the general adult population. Two appraisers assessed the guidelines independently using the Appraisal of Guidelines for Research and Evaluation II (AGREE II) tool. Scores were combined as per the AGREE II users' manual. We identified 10 guidelines meeting the inclusion criteria. The quality of the gonorrhoea treatment guidelines varied. Most scored poorly on Rigour of Development ; information on the evidence review process and methods for formulating recommendations was often missing. The WHO Guidelines for the Treatment of Neisseria gonorrhoeae and UK National Guideline for the Management of Gonorrhoea in Adults scored the highest on Rigour of Development . Methods to address conflicts of interest were often not described in the materials reviewed. Implementation of recommendations was often not addressed. By limiting our study to English-language guidelines, a small number of guidelines we identified were excluded. Our analysis was limited to either published or online materials that were readily available to users. We could not differentiate between items addressed in the development process but not documented from items that were not addressed. Gonorrhoea treatment guidelines may slow antimicrobial resistance. Many current guidelines are not in line with the current guideline development best practices; this might undermine the perceived trustworthiness of guidelines. By identifying current limitations, this study can help improve the quality of future guidelines. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Canadian Contraception Consensus (Part 2 of 4).

PubMed

Black, Amanda; Guilbert, Edith; Costescu, Dustin; Dunn, Sheila; Fisher, William; Kives, Sari; Mirosh, Melissa; Norman, Wendy V; Pymar, Helen; Reid, Robert; Roy, Geneviève; Varto, Hannah; Waddington, Ashley; Wagner, Marie-Soleil; Whelan, Anne Marie; Ferguson, Carrie; Fortin, Claude; Kielly, Maria; Mansouri, Shireen; Todd, Nicole

2015-11-01

To provide guidelines for health care providers on the use of contraceptive methods to prevent pregnancy and on the promotion of healthy sexuality. Guidance for Canadian practitioners on overall effectiveness, mechanism of action, indications, contraindications, non-contraceptive benefits, side effects and risks, and initiation of cited contraceptive methods; family planning in the context of sexual health and general well-being; contraceptive counselling methods; and access to, and availability of, cited contraceptive methods in Canada. Published literature was retrieved through searches of Medline and The Cochrane Database from January 1994 to January 2015 using appropriate controlled vocabulary (e.g., contraception, sexuality, sexual health) and key words (e.g., contraception, family planning, hormonal contraception, emergency contraception). Results were restricted to systematic reviews, randomized control trials/controlled clinical trials, and observational studies published in English from January 1994 to January 2015. Searches were updated on a regular basis and incorporated in the guideline to June 2015. Grey (unpublished) literature was identified through searching the websites of health technology assessment and health technology-related agencies, clinical practice guideline collections, clinical trial registries, and national and international medical specialty societies. The quality of the evidence in this document was rated using the criteria described in the Report of the Canadian Task Force on Preventive Health Care (Table). Chapter 1: Contraception in Canada Summary Statements  1. Canadian women spend a significant portion of their lives at risk of an unintended pregnancy. (II-2)  2. Effective contraceptive methods are underutilized in Canada, particularly among vulnerable populations. (II-2)  3. Long-acting reversible contraceptive methods, including contraceptive implants and intrauterine contraception (copper-releasing and levonorgestrel-releasing devices/systems), are the most effective reversible contraceptive methods and have the highest continuation rates. (II-1)  4. Canada currently does not collect reliable data to determine the use of contraceptive methods, abortion rates, and the prevalence of unintended pregnancy among reproductive-age women. (II-2)  5. A universal subsidy for contraceptive methods as provided by many of Canada's peer nations and a few Canadian provinces may produce health system cost-savings. (II-2)  6. Health Canada approval processes for contraceptives have been less efficient than those of other drug approval agencies and Health Canada processes for other classes of pharmaceuticals. (II-2)  7. It is feasible and safe for contraceptives and family planning services to be provided by appropriately trained allied health professionals such as midwives, registered nurses, nurse practitioners, and pharmacists. (II-2) Recommendations 1. Contraceptive counselling should include a discussion of typical use failure rates and the importance of using the contraceptive method consistently and correctly in order to avoid pregnancy. (II-2A) 2. Women seeking contraception should be counselled on the wide range of effective methods of contraception available, including long-acting reversible contraceptive methods (LARCs). LARCs are the most effective methods of reversible contraception, have high continuation rates, and should be considered when presenting contraceptive options to any woman of reproductive age. (II-2A) 3. Family planning counselling should include counselling on the decline of fertility associated with increasing female age. (III-A) 4. Health policy supporting a universal contraception subsidy and strategies to promote the uptake of highly effective methods as cost-saving measures that improve health and health equity should be considered by Canadian health decision makers. (III-B) 5. Canadian health jurisdictions should consider expanding the scope of practice of other trained professionals such as nurses, nurse practitioners, midwives, and pharmacists and promoting task-sharing in family planning. (II-2B) 6. The Canadian Community Health Survey should include adequate reproductive health indicators in order for health care providers and policy makers to make appropriate decisions regarding reproductive health policies and services in Canada. (III-B) 7. Health Canada processes and policies should be reviewed to ensure a wide range of modern contraceptive methods are available to Canadian women. (III-B) Chapter 2: Contraceptive Care and Access Summary Statements  8. Although there are many contraceptive options in Canada, only a narrow range of contraceptive methods are commonly used by those of reproductive age. (II-3)  9. Condom use decreases with longer relationship tenure and when the sexual partner is considered to be the main partner, likely due to a lower perceived risk of sexually transmitted infection in that relationship. Condom use may also decrease markedly as an unintended consequence when an effective non-barrier method, such as hormonal contraception or intrauterine contraception, is initiated. (II-3) 10. Family planning counselling provides a natural segue into screening for concerns about sexual function or intimate partner violence. (III) 11. Well-informed and well-motivated individuals who have developed skills to practise safer sex behaviours are more likely to use contraceptive and safer sex methods effectively and consistently. (II-2) Recommendations 8. Comprehensive family planning services, including abortion services, should be accessible to all Canadians regardless of geographic location. These services should be confidential, non-judgemental, and respectful of individuals' privacy and cultural contexts. (III-A) 9. A contraceptive visit should include history taking, screening for contraindications, dispensing or prescribing a method of contraception, and exploring contraceptive choice and adherence in the broader context of the individual's sexual behaviour, reproductive health risk, social circumstances, and relevant belief systems. (III-B) 10. Health care providers should provide practical information on the wide range of contraceptive options and their potential non-contraceptive benefits and assist women and their partners in determining the best user-method fit. (III-B) 11. Health care providers should assist women and men in developing the skills necessary to negotiate the use of contraception and the correct and consistent use of a chosen method. (III-B) 12. Contraceptive care should include discussion and management of the risk of sexually transmitted infection, including appropriate recommendations for condom use and dual protection, STI screening, post-exposure prophylaxis, and Hepatitis B and human papillomavirus vaccination. (III-B) 13. Health care providers should emphasize the use of condoms not only for protection against sexually transmitted infection, but also as a back-up method when adherence to a hormonal contraceptive may be suboptimal. (I-A) 14. Health care providers should be aware of current media controversies in reproductive health and acquire relevant evidence-based information that can be briefly and directly communicated to their patients. (III-B) 15. Referral resources for intimate partner violence, sexually transmitted infections, sexual dysfunction, induced abortion services, and child protection services should be available to help clinicians provide contraceptive care in the broader context of women's health. (III-B) Chapter 3: Emergency Contraception Summary Statements 12. The copper intrauterine device is the most effective method of emergency contraception. (II-2) 13. A copper intrauterine device can be used for emergency contraception up to 7 days after unprotected intercourse provided that pregnancy has been ruled out and there are no other contraindications to its insertion. (II-2) 14. Levonorgestrel emergency contraception is effective up to 5 days (120 hours) after intercourse; its effectiveness decreases as the time between unprotected intercourse and ingestion increases. (II-2) 15. Ulipristal acetate for emergency contraception is more effective than levonorgestrel emergency contraception up to 5 days after unprotected intercourse. This difference in effectiveness is more pronounced as the time from unprotected intercourse increases, especially after 72 hours. (I) 16. Hormonal emergency contraception (levonorgestrel emergency contraception and ulipristal acetate for emergency contraception) is not effective if taken on the day of ovulation or after ovulation. (II-2) 17. Levonorgestrel emergency contraception may be less effective in women with a body mass index > 25 kg/m2 and ulipristal acetate for emergency contraception may be less effective in women with a body mass index > 35 kg/m2. However, hormonal emergency contraception may still retain some effectiveness regardless of a woman's body weight or body mass index. (II-2) 18. Hormonal emergency contraception is associated with higher failure rates when women continue to have subsequent unprotected intercourse. (II-2) 19. Hormonal contraception can be initiated the day of or the day following the use of levonorgestrel emergency contraception, with back-up contraception used for the first 7 days. (III) 20. Hormonal contraception can be initiated 5 days following the use of ulipristal acetate for emergency contraception, with back-up contraception used for the first 14 days. (III) Recommendations 16. All emergency contraception should be initiated as soon as possible after unprotected intercourse. (II-2A) 17. Women should be informed that the copper intrauterine device (IUD) is the most effective method of emergency contraception and can be used by any woman with no contraindications to IUD use. (II-3A) 18.

Novel heparan sulfate assay by using automated high-throughput mass spectrometry: application to monitoring and screening for mucopolysaccharidoses

PubMed Central

Shimada, Tsutomu; Kelly, Joan; LaMarr, William A; van Vlies, Naomi; Yasuda, Eriko; Mason, Robert W.; Mackenzie, William; Kubaski, Francyne; Giugliani, Roberto; Chinen, Yasutsugu; Yamaguchi, Seiji; Suzuki, Yasuyuki; Orii, Kenji E.; Fukao, Toshiyuki; Orii, Tadao; Tomatsu, Shunji

2014-01-01

Mucopolysaccharidoses (MPS) are caused by deficiency of one of a group of specific lysosomal enzymes, resulting in excessive accumulation of glycosaminoglycans (GAGs). We previously developed GAG assay methods using liquid chromatography tandem mass spectrometry (LC-MS/MS); however, it takes 4–5 min per sample for analysis. For the large numbers of samples in a screening program, a more rapid process is desirable. The automated high-throughput mass spectrometry (HT-MS/MS) system (RapidFire) integrates a solid phase extraction robot to concentrate and desalt samples prior to direction into the MS/MS without chromatographic separation; thereby allowing each sample to be processed within ten seconds (enabling screening of more than one million samples per year). The aim of this study was to develop a higher throughput system to assay heparan sulfate (HS) using HT-MS/MS, and to compare its reproducibility, sensitivity and specificity with conventional LC-MS/MS. HS levels were measured in blood (plasma and serum) from control subjects and patients with MPS II, III, or IV and in dried blood spots (DBS) from newborn controls and patients with MPS I, II, or III. Results obtained from HT-MS/MS showed 1) that there was a strong correlation of levels of disaccharides derived from HS in blood, between those calculated using conventional LC-MS/MS and HT-MS/MS, 2) that levels of HS in blood were significantly elevated in patients with MPS II and III, but not in MPS IVA, 3) that the level of HS in patients with a severe form of MPS II was higher than that in an attenuated form, 4) that reduction of blood HS level was observed in MPS II patients treated with enzyme replacement therapy or hematopoietic stem cell transplantation, and 5) that levels of HS in newborn DBS were elevated in patients with MPS I, II or III, compared to control newborns. In conclusion, HT-MS/MS provides much higher throughput than LC-MS/MS-based methods with similar sensitivity and specificity in an HS assay, indicating that HT-MS/MS may be feasible for diagnosis, monitoring, and newborn screening of MPS. PMID:25092413

Efficient clinical evaluation of guideline quality: development and testing of a new tool

PubMed Central

2014-01-01

Background Evaluating the methodological quality of clinical practice guidelines is essential before deciding which ones which could best inform policy or practice. One current method of evaluating clinical guideline quality is the research-focused AGREE II instrument. This uses 23 questions scored 1–7, arranged in six domains, which requires at least two independent testers, and uses a formulaic weighted domain scoring system. Following feedback from time-poor clinicians, policy-makers and managers that this instrument did not suit clinical need, we developed and tested a simpler, shorter, binary scored instrument (the iCAHE Guideline Quality Checklist) designed for single users. Methods Content and construct validity, inter-tester reliability and clinical utility were tested by comparing the new iCAHE Guideline Quality Checklist with the AGREE II instrument. Firstly the questions and domains in both instruments were compared. Six randomly-selected guidelines on a similar theme were then assessed by three independent testers with different experience in guideline quality assessment, using both instruments. Per guideline, weighted domain and total AGREE II scores were calculated, using the scoring rubric for three testers. Total iCAHE scores were calculated per guideline, per tester. The linear relationship between iCAHE and AGREE II scores was assessed using Pearson r correlation coefficients. Score differences between testers were assessed for the iCAHE Guideline Quality Checklist. Results There were congruent questions in each instrument in four domains (Scope & Purpose, Stakeholder involvement, Underlying evidence/Rigour, Clarity). The iCAHE and AGREE II scores were moderate to strongly correlated for the six guidelines. There was generally good agreement between testers for iCAHE scores, irrespective of their experience. The iCAHE instrument was preferred by all testers, and took significantly less time to administer than the AGREE II instrument. However, the use of only three testers and six guidelines compromised study power, rendering this research as pilot investigations of the psychometric properties of the iCAHE instrument. Conclusion The iCAHE Guideline Quality Checklist has promising psychometric properties and clinical utility. PMID:24885893

Optimal dose selection accounting for patient subpopulations in a randomized Phase II trial to maximize the success probability of a subsequent Phase III trial.

PubMed

Takahashi, Fumihiro; Morita, Satoshi

2018-02-08

Phase II clinical trials are conducted to determine the optimal dose of the study drug for use in Phase III clinical trials while also balancing efficacy and safety. In conducting these trials, it may be important to consider subpopulations of patients grouped by background factors such as drug metabolism and kidney and liver function. Determining the optimal dose, as well as maximizing the effectiveness of the study drug by analyzing patient subpopulations, requires a complex decision-making process. In extreme cases, drug development has to be terminated due to inadequate efficacy or severe toxicity. Such a decision may be based on a particular subpopulation. We propose a Bayesian utility approach (BUART) to randomized Phase II clinical trials which uses a first-order bivariate normal dynamic linear model for efficacy and safety in order to determine the optimal dose and study population in a subsequent Phase III clinical trial. We carried out a simulation study under a wide range of clinical scenarios to evaluate the performance of the proposed method in comparison with a conventional method separately analyzing efficacy and safety in each patient population. The proposed method showed more favorable operating characteristics in determining the optimal population and dose.

Evaluation of soluble CD30 as an immunologic marker in heart transplant recipients.

PubMed

Spiridon, C; Hunt, J; Mack, M; Rosenthal, J; Anderson, A; Eichhorn, E; Magee, M; Dewey, T; Currier, M; Nikaein, A

2006-12-01

CD30 is an immunologic molecule that belongs to the TNF-R superfamily. CD30 serves as a T-cell signal transducing molecule that is expressed by a subset of activated T lymphocytes, CD45RO+ memory T cells. Augmentation of soluble CD30 during kidney transplant rejection has been reported. Our study sought to determine whether the level of sCD30 prior to heart transplant could categorize patients into high versus low immunologic risk for a poor outcome. A significant correlation was observed between high levels of soluble CD30 and a reduced incidence of infection. None of the 35 patients with high pretransplant levels of sCD30 level (>90 U/mL) developed infections posttransplantation. However, 9 of 65 patients who had low levels of sCD30 (<90 U/mL) developed infections posttransplantation (P < .02). No remarkable differences were noted among the other clinical parameters. The results also showed that the high-definition flow-bead (HDB) assay detected both weak and strong class I and class II HLA antibodies, some of which (weak class II HLA Abs) were undetectable by the anti-human globulin cytotoxicity method. In addition, more antibody specificities were detected by HDB. In conclusion, we have observed that high levels of sCD30 prior to heart transplant may be associated with greater immunologic ability and therefore produce a protective effect on the development of infection post heart transplant. We have also shown that the HDB assay is superior to the visual cytotoxicity method to detect HLA antibodies, especially those to class II HLA antigens.

Shock Test Program. Shock Isolation Design Manual for SAFEGUARD TSE Systems and Equipment.

DTIC Science & Technology

1973-08-01

under the direction of the Huntsville Division, Corps of Engineers. Much of the information in Part I and Part II is extracted from " Development of...49 3.2.2 Configuration Development 1-50 3.2.3 Suspension Arrangements 1-51 TABLE OF CONTENTS (Continued) Page 3.2.4 Platform Design 1-56 3.2.5 Elastic...shock isolation systems were considered in the design of the early NIKE-X facilities. As more descriptive prediction methods were developed and employed

DNA-based identification of spices: DNA isolation, whole genome amplification, and polymerase chain reaction.

PubMed

Focke, Felix; Haase, Ilka; Fischer, Markus

2011-01-26

Usually spices are identified morphologically using simple methods like magnifying glasses or microscopic instruments. On the other hand, molecular biological methods like the polymerase chain reaction (PCR) enable an accurate and specific detection also in complex matrices. Generally, the origins of spices are plants with diverse genetic backgrounds and relationships. The processing methods used for the production of spices are complex and individual. Consequently, the development of a reliable DNA-based method for spice analysis is a challenging intention. However, once established, this method will be easily adapted to less difficult food matrices. In the current study, several alternative methods for the isolation of DNA from spices have been developed and evaluated in detail with regard to (i) its purity (photometric), (ii) yield (fluorimetric methods), and (iii) its amplifiability (PCR). Whole genome amplification methods were used to preamplify isolates to improve the ratio between amplifiable DNA and inhibiting substances. Specific primer sets were designed, and the PCR conditions were optimized to detect 18 spices selectively. Assays of self-made spice mixtures were performed to proof the applicability of the developed methods.

The Evolution of Pd0/PdII-Catalyzed Aromatic Fluorination

PubMed Central

2016-01-01

Conspectus Aromatic fluorides are prevalent in both agrochemical and pharmaceutical agents. However, methods for their rapid and general preparation from widely available starting materials are limited. Traditional approaches such as the Balz–Schiemann and Halex reactions require harsh conditions that limit functional group tolerance and substrate scope. The use of transition metals to affect C–F bond formation has provided some useful alternatives, but a broadly applicable method remains elusive. In contrast to the widespread use of Pd0/PdII catalysis for aryl–Z bond formation (Z = C, N, O), the analogous C–F cross-coupling process was unknown until fairly recently. In large part, this is due to the challenging Ar–F reductive elimination from Pd(II) intermediates. We have discovered that certain biaryl monophosphine ligands are uniquely capable of promoting this transformation. In this Account, we describe the discovery and development of a Pd-catalyzed C–F cross-coupling process and the systematic developments that made this once hypothetical reaction possible. Key to these developments was the discovery of an unusual in situ ligand modification process in which a molecule of substrate is incorporated into the ligand scaffold and the identity of the modifying group is crucial to the outcome of the reaction. This prompted the synthesis of a variety of “premodified” ligands and the identification of one that led to an expanded substrate scope, including (hetero)aryl triflates and bromides. Contemporaneously, a new Pd(0) precatalyst was also discovered that avoids the need to reduce Pd(II) in situ, a process that was often inefficient and led to the formation of byproducts. The use of inexpensive but hygroscopic sources of fluoride necessitates a reaction setup inside of a N2-filled glovebox, limiting the practicality of the method. Thus, a preformed wax capsule was designed to isolate the catalyst and reagents from the atmosphere and permit benchtop storage and setup. This new technology thus removes the requirement to employ a glovebox for the aromatic fluorination process and other air-sensitive protocols. In every catalyst system that we have studied to date, we observed the formation of regioisomeric fluoride side products. Through deuterium labeling studies it was found that they likely arise from a deprotonation event resulting in the formation of HF and a Pd–benzyne intermediate. Through an investigation of the mechanism of this undesired pathway, a new ligand was designed that substantially reduces the formation of the aryl fluoride regioisomer and even allows room-temperature Ar–F reductive elimination from a Pd(II) intermediate. PMID:27656765

Economics of immunization information systems in the United States: assessing costs and efficiency

PubMed Central

Bartlett, Diana L; Molinari, Noelle-Angelique M; Ortega-Sanchez, Ismael R; Urquhart, Gary A

2006-01-01

Background One of the United States' national health objectives for 2010 is that 95% of children aged <6 years participate in fully operational population-based immunization information systems (IIS). Despite important progress, child participation in most IIS has increased slowly, in part due to limited economic knowledge about IIS operations. Should IIS need further improvement, characterizing costs and identifying factors that affect IIS efficiency become crucial. Methods Data were collected from a national sampling frame of the 56 states/cities that received federal immunization grants under U.S. Public Health Service Act 317b and completed the federal 1999 Immunization Registry Annual Report. The sampling frame was stratified by IIS functional status, children's enrollment in the IIS, and whether the IIS had been developed as an independent system or was integrated into a larger system. These sites self-reported IIS developmental and operational program costs for calendar years 1998–2002 using a standardized data collection tool and underwent on-site interviews to verify reported data with information from the state/city financial management system and other financial records. A parametric cost-per-patient-record (CPR) model was estimated. The model assessed the impact of labor and non-labor resources used in development and operations tasks, as well as the impact of information technology, local providers' participation and compliance with federal IIS performance standards (e.g., ensuring the confidentiality and security of information, ensure timely vaccination data at the time of patient encounter, and produce official immunization records). Given the number of records minimizing CPR, the additional amount of resources needed to meet national health goals for the year 2010 was also calculated. Results Estimated CPR was as high as $10.30 and as low as $0.09 in operating IIS. About 20% of IIS had between 2.9 to 3.2 million records and showed CPR estimates of $0.09. Overall, CPR was highly sensitive to local providers' participation. To achieve the 2010 goals, additional aggregated costs were estimated to be $75.6 million nationwide. Conclusion Efficiently increasing the number of records in IIS would require additional resources and careful consideration of various strategies to minimize CPR, such as boosting providers' participation. PMID:16925823

AC orbit bump method of local impedance measurement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smaluk, Victor; Yang, Xi; Blednykh, Alexei

A fast and precise technique of local impedance measurement has been developed and tested at NSLS-II. This technique is based on in-phase sine-wave (AC) excitation of four fast correctors adjacent to the vacuum chamber section, impedance of which is measured. The beam position is measured using synchronous detection. Use of the narrow-band sine-wave signal allows us to improve significantly the accuracy of the orbit bump method. Beam excitation by fast correctors results in elimination of the systematic error caused by hysteresis effect. The systematic error caused by orbit drift is also eliminated because the measured signal is not affected bymore » the orbit motion outside the excitation frequency range. In this article, the measurement technique is described and the result of proof-of-principle experiment carried out at NSLS-II is presented.« less

AC orbit bump method of local impedance measurement

DOE PAGES

Smaluk, Victor; Yang, Xi; Blednykh, Alexei; ...

2017-08-04

A fast and precise technique of local impedance measurement has been developed and tested at NSLS-II. This technique is based on in-phase sine-wave (AC) excitation of four fast correctors adjacent to the vacuum chamber section, impedance of which is measured. The beam position is measured using synchronous detection. Use of the narrow-band sine-wave signal allows us to improve significantly the accuracy of the orbit bump method. Beam excitation by fast correctors results in elimination of the systematic error caused by hysteresis effect. The systematic error caused by orbit drift is also eliminated because the measured signal is not affected bymore » the orbit motion outside the excitation frequency range. In this article, the measurement technique is described and the result of proof-of-principle experiment carried out at NSLS-II is presented.« less

Desertification in the south Junggar Basin, 2000-2009: Part II. Model development and trend analysis

NASA Astrophysics Data System (ADS)

Jiang, Miao; Lin, Yi

2018-07-01

The substantial objective of desertification monitoring is to derive its development trend, which facilitates pre-making policies to handle its potential influences. Aiming at this extreme goal, previous studies have proposed a large number of remote sensing (RS) based methods to retrieve multifold indicators, as reviewed in Part I. However, most of these indicators individually capable of characterizing a single aspect of land attributes, e.g., albedo quantifying land surface reflectivity, cannot show a full picture of desertification processes; few comprehensive RS-based models have either been published. To fill this gap, this Part II was dedicated to developing a RS information model for comprehensively characterizing the desertification and deriving its trend, based on the indicators retrieved in Part I in the same case of the south Junggar Basin, China in the last decade (2000-2009). The proposed model was designed to have three dominant component modules, i.e., the vegetation-relevant sub-model, the soil-relevant sub-model, and the water-relevant sub-model, which synthesize all of the retrieved indicators to integrally reflect the processes of desertification; based on the model-output indices, the desertification trends were derived using the least absolute deviation fitting algorithm. Tests indicated that the proposed model did work and the study area showed different development tendencies for different desertification levels. Overall, this Part II established a new comprehensive RS information model for desertification risk assessment and its trend deriving, and the whole study comprising Part I and Part II advanced a relatively standard framework for RS-based desertification monitoring.

Standards for Lithotripter Performance

NASA Astrophysics Data System (ADS)

Schultheiss, Reiner; Doerffel, Michael

2008-09-01

Standards for lithotripsy have been developed by the International Electrotechnical Commission (IEC) and the FDA. In addition to the existing regulations and norms for the manufacturers, special standards were developed to address a treatment method developed in the early 1980's using extracorporeal shock waves. Initially, the FDA regulated the premarket approval process for lithotripters as a Class III device but reclassified lithotripters in 2000 to a Class II device. The corresponding guidance document for showing the substantial equivalence of new devices with predicate devices will be described in detail. The FDA guidance document is very useful in helping device manufacturers: (i) develop technical performance testing for a shock wave lithotripter within the parameters of an FDA submission, and (ii) conduct clinical performance testing via at least one clinical confirmation study with a small number of subjects. Unfortunately although the submitted data are available at the FDA they are not available in the marketplace and this causes difficulties for physicians in deciding which device to use. The results of the technical performance testing of the LithoGold™ are provided.

Designing of Protein Kinase C β-II Inhibitors against Diabetic complications: Structure Based Drug Design, Induced Fit docking and analysis of active site conformational changes

PubMed Central

Vijayakumar, Balakrishnan; Velmurugan, Devadasan

2012-01-01

Protein Kinase C β-II (PKC β-II) is an important enzyme in the development of diabetic complications like cardiomyopathy, retinopathy, neuropathy, nephropathy and angiopathy. PKC β-II is activated in vascular tissues during diabetic vascular abnormalities. Thus, PKC β-II is considered as a potent drug target and the crystal structure of the kinase domain of PKC β-II (PDB id: 2I0E) was used to design inhibitors using Structure-Based Drug Design (SBDD) approach. Sixty inhibitors structurally similar to Staurosporine were retrieved from PubChem Compound database and High Throughput Virtual screening (HTVs) was carried out with PKC β-II. Based on the HTVs results and the nature of active site residues of PKC β-II, Staurosporine inhibitors were designed using SBDD. Induced Fit Docking (IFD) studies were carried out between kinase domain of PKC β-II and the designed inhibitors. These IFD complexes showed favorable docking score, glide energy, glide emodel and hydrogen bond and hydrophobic interactions with the active site of PKC β-II. Binding free energy was calculated for IFD complexes using Prime MM-GBSA method. The conformational changes induced by the inhibitor at the active site of PKC β-II were observed for the back bone Cα atoms and side-chain chi angles. PASS prediction tool was used to analyze the biological activities for the designed inhibitors. The various physicochemical properties were calculated for the compounds. One of the designed inhibitors successively satisfied all the in silico parameters among the others and seems to be a potent inhibitor against PKC β-II. PMID:22829732

BORE II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bore II, co-developed by Berkeley Lab researchers Frank Hale, Chin-Fu Tsang, and Christine Doughty, provides vital information for solving water quality and supply problems and for improving remediation of contaminated sites. Termed "hydrophysical logging," this technology is based on the concept of measuring repeated depth profiles of fluid electric conductivity in a borehole that is pumping. As fluid enters the wellbore, its distinct electric conductivity causes peaks in the conductivity log that grow and migrate upward with time. Analysis of the evolution of the peaks enables characterization of groundwater flow distribution more quickly, more cost effectively, and with higher resolutionmore » than ever before. Combining the unique interpretation software Bore II with advanced downhole instrumentation (the hydrophysical logging tool), the method quantifies inflow and outflow locations, their associated flow rates, and the basic water quality parameters of the associated formation waters (e.g., pH, oxidation-reduction potential, temperature). In addition, when applied in conjunction with downhole fluid sampling, Bore II makes possible a complete assessment of contaminant concentration within groundwater.« less

A Comparative Observational Study of YSO Classification in Four Small Star-forming H ii Regions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kang, Sung-Ju; Choi, Minho; Kang, Miju

We have developed a new young stellar object (YSO) identification and classification technique using mid-infrared Wide-field Infrared Survey Explorer (WISE) data. We compare this new technique with previous WISE YSO detection and classification methods that used either infrared colors or spectral energy distribution slopes. In this study, we also use the new technique to detect and examine the YSO population associated with four small H ii regions: KR 7, KR 81, KR 120, and KR 140. The relatively simple structure of these regions allows us to effectively use both spatial and temporal constraints to identify YSOs that are potential productsmore » of triggered star formation. We are also able to identify regions of active star formation around these H ii regions that are clearly not influenced by the H ii region expansion, and thus demonstrate that star formation is on-going on megayear timescales in some of these molecular clouds.« less

Solid Phase Extraction of Inorganic Mercury Using 5-Phenylazo-8-hydroxyquinoline and Determination by Cold Vapor Atomic Fluorescence Spectroscopy in Natural Water Samples

PubMed Central

Daye, Mirna; Halwani, Jalal; Hamzeh, Mariam

2013-01-01

8-Hydroxyquinoline (8-HQ) was chosen as a powerful ligand for Hg solid phase extraction. Among several chelating resins based on 8-HQ, 5-phenylazo-8-hydroxyquinoline (5Ph8HQ) is used for mercury extraction in which the adsorption dynamics were fully studied. It has been shown that Hg(II) is totally absorbed by 5Ph8HQ within the first 30 minutes of contact time with t 1/2 5 minutes, following Langmuir adsorption model. At pH 4, the affinity of mercury is unchallenged by other metals except, for Cu(II), which have shown higher Kd value. With these latter characteristics, 5Ph8HQ was examined for the preconcentration of trace levels of Hg(II). The developed method showed quantitative recoveries of Hg(II) with LOD = 0.21 pg mL−1 and RSD = 3–6% using cold vapor atomic fluorescence spectroscopy (CV-AFS) with a preconcentration factor greater than 250. PMID:24459417

Function and regulation of the Mediator complex.

PubMed

Conaway, Ronald C; Conaway, Joan Weliky

2011-04-01

Over the past few years, advances in biochemical and genetic studies of the structure and function of the Mediator complex have shed new light on its subunit architecture and its mechanism of action in transcription by RNA polymerase II (pol II). The development of improved methods for reconstitution of recombinant Mediator subassemblies is enabling more in-depth analyses of basic features of the mechanisms by which Mediator interacts with and controls the activity of pol II and the general initiation factors. The discovery and characterization of multiple, functionally distinct forms of Mediator characterized by the presence or absence of the Cdk8 kinase module have led to new insights into how Mediator functions in both Pol II transcription activation and repression. Finally, progress in studies of the mechanisms by which the transcriptional activation domains (ADs) of DNA binding transcription factors target Mediator have brought to light unexpected complexities in the way Mediator participates in signal transduction. Copyright © 2011 Elsevier Ltd. All rights reserved.

Structural characterization and antioxidant properties of Cu(II) and Ni(II) complexes derived from dicyandiamide

NASA Astrophysics Data System (ADS)

Kertmen, Seda Nur; Gonul, Ilyas; Kose, Muhammet

2018-01-01

New Cu(II) and Ni(II) complexes derived from dicyandiamide were synthesized and characterised by spectroscopic and analytical methods. Molecular structures of the complexes were determined by single crystal X-ray diffraction studies. In the complexes, the Cu(II) or Ni(II) ions are four-coordinate with a slight distorted square planar geometry. The ligands (L-nPen and L-iPen) derived from dicyandiamide formed via nucleophilic addition of alcohol solvent molecule in the presence Cu(II) or Ni(II) ions. Complexes were stabilised by intricate array of hydrogen bonding interactions. Antioxidant activity of the complexes was evaluated by DPPH radical scavenging and CUPRAC methods. The complexes exhibit antioxidant activity, however, their activities were much lower than standard antioxidants (Vitamin C and trolox).

Development of an objective dose distribution analysis method for OSL dating and pilot studies for planetary applications

NASA Astrophysics Data System (ADS)

Lepper, Kenneth Errol

Scope and method of study. Part I: In its simplest expression a luminescence age is the natural absorbed radiation dose (De) divided by the in-situ dose rate. The experimental techniques of Optically Stimulated Luminescence (OSL) dating have evolved to the point were hundreds of Des, and therefore depositional ages can be quickly and conveniently determined for a single sediment sample. The first major objective of this research was to develop an objective analysis method for analyzing dose distribution data and selecting an age-representative dose (Dp). The analytical method was developed based on dose data sets collected from 3 eolian and 3 fluvial sediment samples from Central Oklahoma. Findings and conclusions. Part I: An objective method of presenting the dose distribution data, and a mathematically rigorous means of determining the Dp, as well as a statistically meaningful definition of the uncertainty in Dp have been proposed. The concept of experimental error deconvolution was introduced. In addition a set of distribution shape parameters to facilitate comparison among samples have been defined. These analytical techniques hold the potential to greatly enhance the accuracy and utility of OSL dating for young fluvial sediments. Scope and method of study. Part II: The second major objective of this research was to propose the application of luminescence dating to sediments on Mars. A set of fundamental luminescence dating properties was evaluated for a martian surface materials analog and a polar deposit contextual analog. Findings and conclusions. Part II: The luminescence signals measured from the analogs were found to have a wide dynamic dose response range with no unusual or prohibitive short-term instabilities and were readily reset by exposure to sunlight. These properties form a stable base for continued investigations toward the development of luminescence dating instruments and procedures for Mars.

PCR-based methods for the detection of L1014 kdr mutation in Anopheles culicifacies sensu lato

PubMed Central

Singh, Om P; Bali, Prerna; Hemingway, Janet; Subbarao, Sarala K; Dash, Aditya P; Adak, Tridibes

2009-01-01

Background Anopheles culicifacies s.l., a major malaria vector in India, has developed widespread resistance to DDT and is becoming resistant to pyrethroids–the only insecticide class recommended for the impregnation of bed nets. Knock-down resistance due to a point mutation in the voltage gated sodium channel at L1014 residue (kdr) is a common mechanism of resistance to DDT and pyrethroids. The selection of this resistance may pose a serious threat to the success of the pyrethroid-impregnated bed net programme. This study reports the presence of kdr mutation (L1014F) in a field population of An. culicifacies s.l. and three new PCR-based methods for kdr genotyping. Methods The IIS4-IIS5 linker to IIS6 segments of the para type voltage gated sodium channel gene of DDT and pyrethroid resistant An. culicifacies s.l. population from the Surat district of India was sequenced. This revealed the presence of an A-to-T substitution at position 1014 leading to a leucine-phenylalanine mutation (L1014F) in a few individuals. Three molecular methods viz. Allele Specific PCR (AS-PCR), an Amplification Refractory Mutation System (ARMS) and Primer Introduced Restriction Analysis-PCR (PIRA-PCR) were developed and tested for kdr genotyping. The specificity of the three assays was validated following DNA sequencing of the samples genotyped. Results The genotyping of this An. culicifacies s.l. population by the three PCR based assays provided consistent result and were in agreement with DNA sequencing result. A low frequency of the kdr allele mostly in heterozygous condition was observed in the resistant population. Frequencies of the different genotypes were in Hardy-Weinberg equilibrium. Conclusion The Leu-Phe mutation, which generates the kdr phenotype in many insects, was detected in a pyrethroid and DDT resistant An. culicifacies s.l. population. Three PCR-based methods were developed for kdr genotyping. All the three assays were specific. The ARMS method was refractory to non-specific amplification in non-stringent amplification conditions. The PIRA-PCR assay is able to detect both the codons for the phenylalanine mutation at kdr locus, i.e., TTT and TTC, in a single assay, although the latter codon was not found in the population genotyped. PMID:19594947

Impacts of Outer Continental Shelf (OCS) development on recreation and tourism. Volume 3. Detailed methodology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The final report for the project is presented in five volumes. This volume, Detailed Methodology Review, presents a discussion of the methods considered and used to estimate the impacts of Outer Continental Shelf (OCS) oil and gas development on coastal recreation in California. The purpose is to provide the Minerals Management Service with data and methods to improve their ability to analyze the socio-economic impacts of OCS development. Chapter II provides a review of previous attempts to evaluate the effects of OCS development and of oil spills on coastal recreation. The review also discusses the strengths and weaknesses of differentmore » approaches and presents the rationale for the methodology selection made. Chapter III presents a detailed discussion of the methods actually used in the study. The volume contains the bibliography for the entire study.« less

Single peak parameters technique for simultaneous measurements: Spectrophotometric sequential injection determination of Fe(II) and Fe(III).

PubMed

Kozak, J; Paluch, J; Węgrzecka, A; Kozak, M; Wieczorek, M; Kochana, J; Kościelniak, P

2016-02-01

Spectrophotometric sequential injection system (SI) is proposed to automate the method of simultaneous determination of Fe(II) and Fe(III) on the basis of parameters of a single peak. In the developed SI system, sample and mixture of reagents (1,10-phenanthroline and sulfosalicylic acid) are introduced into a vessel, where in an acid environment (pH≅3) appropriate compounds of Fe(II) and Fe(III) with 1,10-phenanthroline and sulfosalicylic acid are formed, respectively. Then, in turn, air, sample, EDTA and sample again, are introduced into a holding coil. After the flow reversal, a segment of air is removed from the system by an additional valve and as EDTA replaces sulfosalicylic acid forming a more stable colorless compound with Fe(III), a complex signal is registered. Measurements are performed at wavelength 530 nm. The absorbance measured at minimum of the negative peak and the area or the absorbance measured at maximum of the signal can be used as measures corresponding to Fe(II) and Fe(III) concentrations, respectively. The time of the peak registration is about 2 min. Two-component calibration has been applied to analysis. Fe(II) and Fe(III) can be determined within the concentration ranges of 0.04-4.00 and 0.1-5.00 mg L(-1), with precision less than 2.8% and 1.7% (RSD), respectively and accuracy better than 7% (RE). The detection limit is 0.04 and 0.09 mg L(-1) for Fe(II) and Fe(III), respectively. The method was applied to analysis of artesian water samples. Copyright © 2015 Elsevier B.V. All rights reserved.

An In Vitro Comparison of Propex II Apex Locator to Standard Radiographic Method

PubMed Central

Chakravarthy Pishipati, Kalyan Vinayak

2013-01-01

Introduction The aim of this in vitro study was to compare the accuracy of radiography in assessing working length to Propex II apex locator. Materials and Methods Thirty single canal extracted human teeth with patent apical foramen were selected. Access cavities were prepared. Anatomic length (AL) was determined by inserting a K-file into the root canal until the file tip was just visible at the most coronal aspect of the apical foramen; subsequently 0.5 mm was deducted from this measured length. Working length by radiographic method (RL) was determined using Ingle’s method. Propex II apex locator was used to determine the electronic working length (EL). From these calculated lengths, AL was deducted to obtain D-value. D-value in the range of +/-0.5 mm was considered to be acceptable. Results The percentage accuracy of RL and Propex II apex locator was 76.6% and 86.6%, respectively. Paired t-test revealed significant difference between the RL and Propex II apex locator (P<0.05). Conclusion: Under these in vitro conditions, Propex II apex locator has determined working length more accurately than radiographic method. PMID:23922572

Adaptive Behaviour Assessment System: Indigenous Australian Adaptation Model (ABAS: IAAM)

ERIC Educational Resources Information Center

du Plessis, Santie

2015-01-01

The study objectives were to develop, trial and evaluate a cross-cultural adaptation of the Adaptive Behavior Assessment System-Second Edition Teacher Form (ABAS-II TF) ages 5-21 for use with Indigenous Australian students ages 5-14. This study introduced a multiphase mixed-method design with semi-structured and informal interviews, school…

Teaching Literature Using Multimedia. Final Report: Fund for the Improvement of Postsecondary Education.

ERIC Educational Resources Information Center

Stalker, Sandra

"Journey Home," an interactive CD-ROM program about Homer's "Odyssey," was produced at North Shore Community College (Massachusetts) to create an innovative method for teaching literature. Based on a prototype developed on an Apple II, the program incorporates video, text, graphics, music, and artwork related to the Odyssey and…

26 CFR 1.482-1 - Allocation of income and deductions among taxpayers.

Code of Federal Regulations, 2013 CFR

2013-04-01

... determining the comparability of two transactions include— (A) Research and development; (B) Product design... illustrates the principles of this paragraph (d)(4)(ii)(C). Example. Couture, a U.S. apparel design....482-8 provides examples illustrating the application of the best method rule. Finally, § 1.482-9...

26 CFR 1.482-1 - Allocation of income and deductions among taxpayers.

Code of Federal Regulations, 2012 CFR

2012-04-01

... determining the comparability of two transactions include— (A) Research and development; (B) Product design... illustrates the principles of this paragraph (d)(4)(ii)(C). Example. Couture, a U.S. apparel design....482-8 provides examples illustrating the application of the best method rule. Finally, § 1.482-9...

26 CFR 1.482-1 - Allocation of income and deductions among taxpayers.

Code of Federal Regulations, 2014 CFR

2014-04-01

... determining the comparability of two transactions include— (A) Research and development; (B) Product design... illustrates the principles of this paragraph (d)(4)(ii)(C). Example. Couture, a U.S. apparel design....482-8 provides examples illustrating the application of the best method rule. Finally, § 1.482-9...

26 CFR 1.482-1 - Allocation of income and deductions among taxpayers.

Code of Federal Regulations, 2011 CFR

2011-04-01

... determining the comparability of two transactions include— (A) Research and development; (B) Product design... illustrates the principles of this paragraph (d)(4)(ii)(C). Example. Couture, a U.S. apparel design....482-8 provides examples illustrating the application of the best method rule. Finally, § 1.482-9...

School Climate and Continuity of Adolescent Personality Disorder Symptoms

ERIC Educational Resources Information Center

Kasen, Stephanie; Cohen, Patricia; Chen, Henian; Johnson, Jeffrey G.; Crawford, Thomas N.

2009-01-01

Background: Schools are key social contexts for shaping development and behavior in youths; yet, little is known of their influence on adolescent personality disturbance. Method: A community-based sample of 592 adolescents was assessed for family and school experiences, Axis I psychiatric disorders, and Axis II personality disorder (PD) symptoms,…

Development of a Charged-particle Accumulator Using an RF Confinement Method II

DTIC Science & Technology

2006-08-24

Ryugo Hayano, Ph.D., Professor Department of Physics, Graduate School of Science University of Tokyo 7-3-1 Hongo , Bunkyo-ku...NAME(S) AND ADDRESS(ES) University of Tokyo,7-3-1 Hongo , Bunkyo-ku,Tokyo 113-0033,Japan,JP,113-0033 8. PERFORMING ORGANIZATION REPORT NUMBER AOARD

Gold(I) NHC-based homo- and heterobimetallic complexes: synthesis, characterization and evaluation as potential anticancer agents.

PubMed

Bertrand, Benoît; Citta, Anna; Franken, Inge L; Picquet, Michel; Folda, Alessandra; Scalcon, Valeria; Rigobello, Maria Pia; Le Gendre, Pierre; Casini, Angela; Bodio, Ewen

2015-09-01

While N-heterocyclic carbenes (NHC) are ubiquitous ligands in catalysis for organic or industrial syntheses, their potential to form transition metal complexes for medicinal applications has still to be exploited. Within this frame, we synthesized new homo- and heterobimetallic complexes based on the Au(I)-NHC scaffold. The compounds were synthesized via a microwave-assisted method developed in our laboratories using Au(I)-NHC complexes carrying a pentafluorophenol ester moiety and another Au(I) phosphane complex or a bipyridine ligand bearing a pendant amine function. Thus, we developed two different methods to prepare homo- and heterobimetallic complexes (Au(I)/Au(I) or Au(I)/Cu(II), Au(I)/Ru(II), respectively). All the compounds were fully characterized by several spectroscopic techniques including far infrared, and were tested for their antiproliferative effects in a series of human cancer cells. They showed moderate anticancer properties. Their toxic effects were also studied ex vivo using the precision-cut tissue slices (PCTS) technique and initial results concerning their reactivity with the seleno-enzyme thioredoxin reductase were obtained.

Comparative transition performance of several nosetip materials as defined by ballistics-range testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reda, D.C.

1979-01-01

Requirements and techniques for conducting aerothermodynamic tests of reentry body nosetips/materials in hypersonic ballistics-range environments (ISA 22nd IIS), and associated data interpretation/analyses methods using interactive graphics (ISA 24th IIS) have been outlined. Such testing, which centers on the utilization of electro-optical pyrometry for the measurement of nosetip surface temperature distributions, has provided both the aerothermodynamics and materials-development communities with valuable new capabilities. From an aerothermodynamics standpoint, experimental results serve to test the validity of existing computer codes/correlations, as well as to expand the data base necessary for the generation of improved predictive techniques. From a materials-development standpoint, results serve tomore » define relationships between fabrication/processing methods and associated material thermal response as well as to provide for relative ranking of candidate materials under controlled reentry conditions. Following these multipurpose objectives, ballistic-range tests of preablated graphite and carbon/carbon composite nosetips have been conducted. Results are presented herein which illustrate the comparative transition performance of five nosetip materials from both mean and statistical (degree-of-asymmetry) viewpoints.« less

Developing a research agenda for reducing the stigma of addictions, part II: Lessons from the mental health stigma literature.

PubMed

Corrigan, Patrick W; Schomerus, Georg; Shuman, Valery; Kraus, Dana; Perlick, Debbie; Harnish, Autumn; Kulesza, Magdalena; Kane-Willis, Kathleen; Qin, Sang; Smelson, David

2017-01-01

Although advocates and providers identify stigma as a major factor in confounding the recovery of people with SUDs, research on addiction stigma is lacking, especially when compared to the substantive literature examining the stigma of mental illness. A comprehensive review of the stigma literature that yielded empirically supported concepts and methods from the mental health arena was contrasted with the much smaller and mostly descriptive findings from the addiction field. In Part I of this two part paper (American Journal of Addictions, Vol 26, pages 59-66, this issue), constructs and methods from the mental health stigma literature were used to summarize research that seeks to understand the phenomena of addiction stigma. In Paper II, we use this summary, as well as the extensive literature on mental illness stigma change, to outline a research program to develop and evaluate strategies meant to diminish impact on public and self-stigma (eg, education and contact). The paper ends with recommendations for next steps in addiction stigma research. (Am J Addict 2017;26:67-74). © 2016 American Academy of Addiction Psychiatry.

Development and demonstration of techniques for reducing occupational radiation doses during refueling outages. Task 1. Steam generator channel head decontamination

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abrams, W.T.; Cope, A.W.; Orsulak, R.M.

The overall objective of Task 1 was to demonstrate an effective method for removing tenacious corrosion products in a pressurized water reactor steam generator and thus significantly reduce radiation exposure during subsequent maintenance activities. Various decontamination methods were evaluated and a multistep, low concentration chemical process originated by Kraftwerk Union A.G. (KWU) of the Federal Republic of Germany was selected. The process was further developed and tested by C-E and KWU in West Germany and at C-E's facilities in Windsor, Connecticut. C-E designed, fabricated and tested a portable system to apply the process at Millstone Point II. The decontamination ofmore » the primary channel heads of the two Millstone steam generators was performed by C-E and NUSCO during the 1983 refueling shutdown of Millstone Point II plant. Results of the decontamination were very satisfactory. NUSCO determined that a net savings of 3660 man-rem of personnel exposure was realized during the decontamination demonstration and the subsequent maintenance work on the steam generators.« less

Modification of Chitin with Kraft Lignin and Development of New Biosorbents for Removal of Cadmium(II) and Nickel(II) Ions

PubMed Central

Wysokowski, Marcin; Klapiszewski, Łukasz; Moszyński, Dariusz; Bartczak, Przemysław; Szatkowski, Tomasz; Majchrzak, Izabela; Siwińska-Stefańska, Katarzyna; Bazhenov, Vasilii V.; Jesionowski, Teofil

2014-01-01

Novel, functional materials based on chitin of marine origin and lignin were prepared. The synthesized materials were subjected to physicochemical, dispersive-morphological and electrokinetic analysis. The results confirm the effectiveness of the proposed method of synthesis of functional chitin/lignin materials. Mechanism of chitin modification by lignin is based on formation of hydrogen bonds between chitin and lignin. Additionally, the chitin/lignin materials were studied from the perspective of waste water treatment. The synthetic method presented in this work shows an attractive and facile route for producing low-cost chitin/lignin biosorbents with high efficiency of nickel and cadmium adsorption (88.0% and 98.4%, respectively). The discovery of this facile method of synthesis of functional chitin/lignin materials will also have a significant impact on the problematic issue of the utilization of chitinous waste from the seafood industry, as well as lignin by-products from the pulp and paper industry. PMID:24727394

Small-Molecule Fluorescent Sensors for Investigating Zinc Metalloneurochemistry

PubMed Central

Nolan, Elizabeth M.; Lippard, Stephen J.

2008-01-01

Conspectus Metal ions are involved in many neurobiological processes relevant to human health and disease. The metalloneurochemistry of Zn(II) is of substantial current interest. Zinc is the second most abundant d-block metal ion in the human brain and its distribution varies, with relatively high concentrations found in the hippocampus. Brain zinc is generally divided into two categories: protein-bound and loosely-bound. The latter pool is also referred to as histochemically observable, chelatable, labile, or mobile zinc. The neurophysiological and neuropathological significance of such mobile Zn(II) remains enigmatic. Studies of Zn(II) distribution, translocation, and function in vivo require tools for its detection. Because Zn(II) has a closed-shell d10 configuration and no convenient spectroscopic signature, fluorescence is a suitable method for monitoring Zn(II) in biological contexts. This Account summarizes work by our laboratory addressing the design, preparation, characterization, and use of small-molecule fluorescent sensors for imaging mobile Zn(II) in living cells and samples of brain tissue. These sensors provide “turn-on” or ratiometric Zn(II) detection in aqueous solution at neutral pH. By making alterations to the Zn(II)-binding unit and fluorophore platform, we have devised sensors with varied photophysical and metal-binding properties. We used several of these probes to image Zn(II) distribution, uptake, and mobilization in a variety of cell types, including neuronal cultures. Goals for the future include developing strategies for multi-color imaging, further defining the quenching and turn-on mechanisms of the sensors, and employing the probes to elucidate the functional significance of Zn(II) in neurobiology. PMID:18989940

A systematic critical appraisal of non-pharmacological management of rheumatoid arthritis with Appraisal of Guidelines for Research and Evaluation II.

PubMed

Brosseau, Lucie; Rahman, Prinon; Poitras, Stéphane; Toupin-April, Karine; Paterson, Gail; Smith, Christine; King, Judy; Casimiro, Lynn; De Angelis, Gino; Loew, Laurianne; Cavallo, Sabrina; Ewan, Jessica Mc

2014-01-01

Clinical practice guidelines (CPGs) have been developed to summarize evidence about the management of rheumatoid arthritis (RA) and facilitate the uptake of evidence-based knowledge by consumers, health professionals, health administrators and policy makers. The objectives of this review was to assess the quality of CPGS on non-pharmacological management of RA with a standardized and validated instrument--the Appraisal of Guidelines for Research and Evaluation (AGREE II) tool and summarize the key recommendations from these CPGs. Scientific literature databases from 2001 to 2013 were systematically searched and a total of 13 CPGs for RA was identified. Only a minority of AGREE II domains were effectively addressed by the CPGS. Scope and purpose was effectively addressed in 10 out of 13 CPGs, stakeholder involvement in 11 CPGs, rigor of development in 6 CPGs, clarity/presentation in 9 CPGs, editorial independence in 1 CPGs, and applicability in none of the CPGs. The overall quality of the included CPGs according to the 7-point AGREE II scoring system was 4.8 ± 1.04. Patient education/self-management, aerobic, dynamic and stretching exercises were the commonly recommended for the non-pharmacological management of RA by the high-quality CPGs. The general clinical management recommendations tended to be similar among high-quality CPGs. Non-pharmacological management interventions were superficially addressed in more than half of the selected CPGs. CPGs creators should use the AGREE II criteria when developing guidelines. Innovative and effective methods of CPGs implementation to users are needed to ultimately enhance the quality of life of arthritic individuals. In addition, it was difficult to establish between strongly recommended, recommended and weakly recommended, as there is no consensus between the strength of the recommendations between the appraised CPGs.

Determination of mercury in ambient water samples by anodic stripping voltammetry on screen-printed gold electrodes.

PubMed

Bernalte, E; Marín Sánchez, C; Pinilla Gil, E

2011-03-09

The applicability of commercial screen-printed gold electrodes (SPGEs) for the determination of Hg(II) in ambient water samples by square wave anodic stripping voltammetry has been demonstrated. Electrode conditioning procedures, chemical and instrumental variables have been optimized to develop a reliable method capable of measuring dissolved mercury in the low ng mL(-1) range (detection limit 1.1 ng mL(-1)), useful for pollution monitoring or screening purposes. The proposed method was tested with the NIST 1641d Mercury in Water Standard Reference Material (recoveries 90.0-110%) and the NCS ZC 76303 Mercury in Water Certified Reference Material (recoveries 82.5-90.6%). Waste water samples from industrial origin and fortified rain water samples were assayed for mercury by the proposed method and by a reference ICP-MS method, with good agreement. Screen printing technology thus opens a useful way for the construction of reliable electrochemical sensors for decentralized or even field Hg(II) testing. Copyright © 2011 Elsevier B.V. All rights reserved.

Parallel heat transport in reversed shear magnetic field configurations

NASA Astrophysics Data System (ADS)

Blazevski, D.; Del-Castillo-Negrete, D.

2012-03-01

Transport in magnetized plasmas is a key problem in controlled fusion, space plasmas, and astrophysics. Three issues make this problem particularly challenging: (i) The extreme anisotropy between the parallel (i.e., along the magnetic field), χ, and the perpendicular, χ, conductivities (χ/χ may exceed 10^10 in fusion plasmas); (ii) Magnetic field lines chaos; and (iii) Nonlocal parallel transport. We have recently developed a Lagrangian Green's function (LG) method to solve the local and non-local parallel (χ/χ->∞) transport equation applicable to integrable and chaotic magnetic fields. footnotetext D. del-Castillo-Negrete, L. Chac'on, PRL, 106, 195004 (2011); D. del-Castillo-Negrete, L. Chac'on, Phys. Plasmas, APS Invited paper, submitted (2011). The proposed method overcomes many of the difficulties faced by standard finite different methods related to the three issues mentioned above. Here we apply the LG method to study transport in reversed shear configurations. We focus on the following problems: (i) separatrix reconnection of magnetic islands and transport; (ii) robustness of shearless, q'=0, transport barriers; (iii) leaky barriers and shearless Cantori.

Recovering the dynamics of root growth and development using novel image acquisition and analysis methods

PubMed Central

Wells, Darren M.; French, Andrew P.; Naeem, Asad; Ishaq, Omer; Traini, Richard; Hijazi, Hussein; Bennett, Malcolm J.; Pridmore, Tony P.

2012-01-01

Roots are highly responsive to environmental signals encountered in the rhizosphere, such as nutrients, mechanical resistance and gravity. As a result, root growth and development is very plastic. If this complex and vital process is to be understood, methods and tools are required to capture the dynamics of root responses. Tools are needed which are high-throughput, supporting large-scale experimental work, and provide accurate, high-resolution, quantitative data. We describe and demonstrate the efficacy of the high-throughput and high-resolution root imaging systems recently developed within the Centre for Plant Integrative Biology (CPIB). This toolset includes (i) robotic imaging hardware to generate time-lapse datasets from standard cameras under infrared illumination and (ii) automated image analysis methods and software to extract quantitative information about root growth and development both from these images and via high-resolution light microscopy. These methods are demonstrated using data gathered during an experimental study of the gravitropic response of Arabidopsis thaliana. PMID:22527394

Recovering the dynamics of root growth and development using novel image acquisition and analysis methods.

PubMed

Wells, Darren M; French, Andrew P; Naeem, Asad; Ishaq, Omer; Traini, Richard; Hijazi, Hussein I; Hijazi, Hussein; Bennett, Malcolm J; Pridmore, Tony P

2012-06-05

Roots are highly responsive to environmental signals encountered in the rhizosphere, such as nutrients, mechanical resistance and gravity. As a result, root growth and development is very plastic. If this complex and vital process is to be understood, methods and tools are required to capture the dynamics of root responses. Tools are needed which are high-throughput, supporting large-scale experimental work, and provide accurate, high-resolution, quantitative data. We describe and demonstrate the efficacy of the high-throughput and high-resolution root imaging systems recently developed within the Centre for Plant Integrative Biology (CPIB). This toolset includes (i) robotic imaging hardware to generate time-lapse datasets from standard cameras under infrared illumination and (ii) automated image analysis methods and software to extract quantitative information about root growth and development both from these images and via high-resolution light microscopy. These methods are demonstrated using data gathered during an experimental study of the gravitropic response of Arabidopsis thaliana.

Quantifying Impacts of Urban Growth Potential on Army Training Capabilities

DTIC Science & Technology

2017-09-12

Capacity” ERDC/CERL TR-17-34 ii Abstract Building on previous studies of urban growth and population effects on U.S. military installations and...combat team studies . CAA has developed an iterative process that builds on Military Value Anal- ysis (MVA) models that include a set of attributes that...Methods and tools were developed to support a nationwide analysis. This study focused on installations operating training areas that were high

A new approach for performing contamination control bakeouts in JPL thermal vacuum test chambers

NASA Technical Reports Server (NTRS)

Johnson, Kenneth R.; Taylor, Daniel M.; Lane, Robert W.; Cortez, Maximo G.; Anderson, Mark R.

1992-01-01

Contamination control requirements for the Wide Field/Planetary Camera II (WF/PC II) are necessarily stringent to protect against post-launch contamination of the sensitive optical surfaces, particularly the cold charge coupled device (CCD) imaging surfaces. Typically, thermal vacuum test chambers have employed a liquid nitrogen (LN2) cold trap to collect outgassed contaminants. This approach has the disadvantage of risking recontamination of the test article from shroud offgassing during post-test warmup of the chamber or from any shroud warming of even a few degrees during the bakeout process. By using an enclave, essentially a chamber within a chamber, configured concentrically and internally within an LN2 shroud, a method was developed, based on a design concept by Taylor, for preventing recontamination of test articles during bakeouts and subsequent post-test warmup of the vacuum chamber. Enclaves for testing WF/PC II components were designed and fabricated, then installed in three of JPL's Environmental Test Lab chambers. The design concepts, operating procedures, and test results of this development are discussed.

Dye-doped nanostructure polypyrrole film for electrochemically switching solid-phase microextraction of Ni(II) and ICP-OES analysis of waste water.

PubMed

Shamaeli, Ehsan; Alizadeh, Naader

2012-01-01

A nanostructure fiber based on conducting polypyrrole synthesized by an electrochemical method has been developed, and used for electrochemically switching solid-phase microextraction (ES-SPME). The ES-SPME was prepared by the doping of eriochrome blue in polypyrrole (PPy-ECB) and used for selectively extracting the Ni(II) cation in the presence of some transition and heavy metal ions. The cation-exchange behavior of electrochemically prepared polypyrrole on stainless-steel with and without eriochrome blue (ECB) dye was characterized using ICP-OES analysis. The effects of the scan rate for electrochemical synthesis, uptake and the release potential on the extraction behavior of the PPy-ECB conductive fiber were studied. Uptake and release time profiles show that the process of electrically switched cation exchange could be completed within 250 s. The results of the present study point concerning the possibility of developing a selective extraction process for Ni(II) from waste water was explored using such a nanostructured PPy-ECB film through an electrically switched cation exchange. 2012 © The Japan Society for Analytical Chemistry

A Probabilistic Finite Element Analysis of Residual Stress Formation in Shrink-Fit Ceramic/Steel Gun Barrels

DTIC Science & Technology

2002-01-01

the present work, the Advanced Mean Value method developed by Millwater and co-workers is used [6-10]. II.1.1 Advanced Mean-Value Method The...Engineering A, submitted for publication, December, , 2001. 6. H. R. Millwater and Y.-T. Wu, “Computational Structural Reliability Analysis of a...Turbine Blade,” Proceedings International Gas Turbine and Aeroengine Congress and Exposition, Cincinnati, OH, May 24-27, 1993. 7. Millwater , H.R., Y

40 CFR 52.823 - PM10 State Implementation Plan Development in Group II Areas.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Development in Group II Areas. 52.823 Section 52.823 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... State Implementation Plan Development in Group II Areas. The Iowa Department of Natural Resources...: Three groups within the State of Iowa have been classified as Group II areas for fine particulate (PM-10...

40 CFR 52.823 - PM10 State Implementation Plan Development in Group II Areas.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Development in Group II Areas. 52.823 Section 52.823 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... State Implementation Plan Development in Group II Areas. The Iowa Department of Natural Resources...: Three groups within the State of Iowa have been classified as Group II areas for fine particulate (PM-10...

40 CFR 52.823 - PM10 State Implementation Plan Development in Group II Areas.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Development in Group II Areas. 52.823 Section 52.823 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... State Implementation Plan Development in Group II Areas. The Iowa Department of Natural Resources...: Three groups within the State of Iowa have been classified as Group II areas for fine particulate (PM-10...

40 CFR 52.823 - PM10 State Implementation Plan Development in Group II Areas.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Development in Group II Areas. 52.823 Section 52.823 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... State Implementation Plan Development in Group II Areas. The Iowa Department of Natural Resources...: Three groups within the State of Iowa have been classified as Group II areas for fine particulate (PM-10...

40 CFR 52.823 - PM10 State Implementation Plan Development in Group II Areas.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Development in Group II Areas. 52.823 Section 52.823 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... State Implementation Plan Development in Group II Areas. The Iowa Department of Natural Resources...: Three groups within the State of Iowa have been classified as Group II areas for fine particulate (PM-10...

Quality monitoring methods of initial and terminal manufacture of LiFePO4 based lithium ion batteries by capillary electrophoresis.

PubMed

Xie, Xia; Yang, Yang; Zhou, Henghui; Li, Meixian; Zhu, Zhiwei

2018-03-01

Magnetic impurities of lithium ion battery degrade both the capacity and cycling rates, even jeopardize the safety of the battery. During the material manufacture of LiFePO 4 , two opposite and extreme cases (trace impurity Fe(II) with high content of Fe(III) background in FePO 4 of initial end and trace Fe(III) with high content of Fe(II) background in LiFePO 4 of terminal end) can result in the generation of magnetic impurities. Accurate determination of impurities and precise evaluation of raw material or product are necessary to ensure reliability, efficiency and economy in lithium ion battery manufacture. Herein, two kinds of rapid, simple, and sensitive capillary electrophoresis (CE) methods are proposed for quality monitoring of initial and terminal manufacture of LiFePO 4 based lithium ion batteries. The key to success includes the smart use of three common agents 1,10-phenanthroline (phen), EDTA and cetyltrimethyl ammonium bromide (CTAB) in sample solution or background electrolyte (BGE), as well as sample stacking technique of CE feature. Owing to the combination of field-enhanced sample injection (FESI) technique with high stacking efficiency, detection limits of 2.5nM for Fe(II) and 0.1μM for Fe(III) were obtained corresponding to high content of Fe(III) and Fe(II), respectively. The good recoveries and reliability demonstrate that the developed methods are accurate approaches for quality monitoring of LiFePO 4 manufacture. Copyright © 2017 Elsevier B.V. All rights reserved.

Design and Development of Mixed-Metal Oxide Photocatalysts: the Band Engineering Approach

NASA Astrophysics Data System (ADS)

Boltersdorf, Jonathan Andrew

The design and development of mixed-metal oxides incorporating Ag(I), Pb(II), Sn(II), and Bi(III), i.e., with filled d10 or d10s2 electron configurations, have yielded new approaches to tune optical and photocatalytic properties for solar energy conversion. My research efforts in the area of solid-state photochemistry have focused on utilizing flux-mediated ion-exchange methods in conjunction with the band engineering approach to synthesize new materials for solar energy driven total water splitting. Layered perovskite phases and the polysomatic family of tantalate/niobate structures, with the general formula Am+ ( n+1)/mB(3 n+1)O(8n +3) (A = Na, Ag; B = Ta, Nb), have received increasing attention owing to their synthetic flexibility, tunable optical band gaps, and photocatalytic activities for total water splitting. Structures in the family of A m+ (n+1)/ mB(3n +1)O(8n+3) structures are based on the stacking of pentagonal bipyramidal layers, where n defines the average thickness (1 ≤ n ≤ 2) of the BO7 layers that alternate with isolated BO6 octahedra surrounded by A-site cations. Synthetic limitations in the discovery of new phases within the layered perovskites and the Am + (n+1)/mB(3 n+1)O(8n +3) structural families can be addressed with the aid of a metal-salt solvent, known as the molten-salt flux method. The flux synthetic route requires the use of an inorganic salt heated above its melting temperature in order to serve as a solvent system for crystallization. Molten fluxes allow for synthetic modification of particle characteristics and can enable the low temperature stabilization of new compositions and phases with limited stability using ion-exchange reactions (e.g., PbTa4O11, AgLaNb 2O7). Solid-state and flux-mediated exchange methods were utilized in order to synthetically explore and investigate the layered perovskites ALaNb2O7, AA2Nb3O 10, A'2La2Ti3O10 (A' = Rb, Ag; A = Ca, Sr), the Am+ (n+1)/mB 3n+1O(8 n+3) structural family (Am + = Na(I), Ag(I), Pb(II), Sn(II), Bi(III); B = Ta, Nb), Pb3Ta 4O13, PbTa2O6, Bi7Ta 3O18, and Sn2TiO4. The impact of the dimensionality of the structural features on the photocatalytic activities of the metal-oxides will be examined. A comparison of the influence of Ag(I), Pb(II), Sn(II), and Bi(III) cations in combination with Ti(IV), Nb(V), and Ta(V) cations on the optical properties and photocatalytic rates of the mixed-metal oxides will be presented. The results of these investigations have led to new insights into synthetic strategies for the development of new metal-oxide photocatalysts, which have aided in understanding the effects of transition and post-transition metals, structural features, and flux-mediated synthesis methods on the optical and photocatalytic properties of metal oxides for solar fuel production.

Use of a Smartphone as a Colorimetric Analyzer in Paper-based Devices for Sensitive and Selective Determination of Mercury in Water Samples.

PubMed

Jarujamrus, Purim; Meelapsom, Rattapol; Pencharee, Somkid; Obma, Apinya; Amatatongchai, Maliwan; Ditcharoen, Nadh; Chairam, Sanoe; Tamuang, Suparb

2018-01-01

A smartphone application, called CAnal, was developed as a colorimetric analyzer in paper-based devices for sensitive and selective determination of mercury(II) in water samples. Measurement on the double layer of a microfluidic paper-based analytical device (μPAD) fabricated by alkyl ketene dimer (AKD)-inkjet printing technique with special design doped with unmodified silver nanoparticles (AgNPs) onto the detection zones was performed by monitoring the gray intensity in the blue channel of AgNPs, which disintegrated when exposed to mercury(II) on μPAD. Under the optimized conditions, the developed approach showed high sensitivity, low limit of detection (0.003 mg L -1 , 3SD blank/slope of the calibration curve), small sample volume uptake (two times of 2 μL), and short analysis time. The linearity range of this technique ranged from 0.01 to 10 mg L -1 (r 2 = 0.993). Furthermore, practical analysis of various water samples was also demonstrated to have acceptable performance that was in agreement with the data from cold vapor atomic absorption spectrophotometry (CV-AAS), a conventional method. The proposed technique allows for a rapid, simple (instant report of the final mercury(II) concentration in water samples via smartphone display), sensitive, selective, and on-site analysis with high sample throughput (48 samples h -1 , n = 3) of trace mercury(II) in water samples, which is suitable for end users who are unskilled in analyzing mercury(II) in water samples.

Low-dose cone-beam CT via raw counts domain low-signal correction schemes: Performance assessment and task-based parameter optimization (Part II. Task-based parameter optimization).

PubMed

Gomez-Cardona, Daniel; Hayes, John W; Zhang, Ran; Li, Ke; Cruz-Bastida, Juan Pablo; Chen, Guang-Hong

2018-05-01

Different low-signal correction (LSC) methods have been shown to efficiently reduce noise streaks and noise level in CT to provide acceptable images at low-radiation dose levels. These methods usually result in CT images with highly shift-variant and anisotropic spatial resolution and noise, which makes the parameter optimization process highly nontrivial. The purpose of this work was to develop a local task-based parameter optimization framework for LSC methods. Two well-known LSC methods, the adaptive trimmed mean (ATM) filter and the anisotropic diffusion (AD) filter, were used as examples to demonstrate how to use the task-based framework to optimize filter parameter selection. Two parameters, denoted by the set P, for each LSC method were included in the optimization problem. For the ATM filter, these parameters are the low- and high-signal threshold levels p l and p h ; for the AD filter, the parameters are the exponents δ and γ in the brightness gradient function. The detectability index d' under the non-prewhitening (NPW) mathematical observer model was selected as the metric for parameter optimization. The optimization problem was formulated as an unconstrained optimization problem that consisted of maximizing an objective function d'(P), where i and j correspond to the i-th imaging task and j-th spatial location, respectively. Since there is no explicit mathematical function to describe the dependence of d' on the set of parameters P for each LSC method, the optimization problem was solved via an experimentally measured d' map over a densely sampled parameter space. In this work, three high-contrast-high-frequency discrimination imaging tasks were defined to explore the parameter space of each of the LSC methods: a vertical bar pattern (task I), a horizontal bar pattern (task II), and a multidirectional feature (task III). Two spatial locations were considered for the analysis, a posterior region-of-interest (ROI) located within the noise streaks region and an anterior ROI, located further from the noise streaks region. Optimal results derived from the task-based detectability index metric were compared to other operating points in the parameter space with different noise and spatial resolution trade-offs. The optimal operating points determined through the d' metric depended on the interplay between the major spatial frequency components of each imaging task and the highly shift-variant and anisotropic noise and spatial resolution properties associated with each operating point in the LSC parameter space. This interplay influenced imaging performance the most when the major spatial frequency component of a given imaging task coincided with the direction of spatial resolution loss or with the dominant noise spatial frequency component; this was the case of imaging task II. The performance of imaging tasks I and III was influenced by this interplay in a smaller scale than imaging task II, since the major frequency component of task I was perpendicular to imaging task II, and because imaging task III did not have strong directional dependence. For both LSC methods, there was a strong dependence of the overall d' magnitude and shape of the contours on the spatial location within the phantom, particularly for imaging tasks II and III. The d' value obtained at the optimal operating point for each spatial location and imaging task was similar when comparing the LSC methods studied in this work. A local task-based detectability framework to optimize the selection of parameters for LSC methods was developed. The framework takes into account the potential shift-variant and anisotropic spatial resolution and noise properties to maximize the imaging performance of the CT system. Optimal parameters for a given LSC method depend strongly on the spatial location within the image object. © 2018 American Association of Physicists in Medicine.

Layered double hydroxide-enhanced luminescence in a Fenton-like system for selective sensing of cobalt in Hela cells

NASA Astrophysics Data System (ADS)

Yu, Mei; Yuan, Zhiqin; Lu, Chao

2017-09-01

This work presented a facile and eco-friendly method for the determination of cobalt ions (Co(II)) in living cells based on layered double hydroxides (Mg-Al CO3-LDHs) enhanced chemiluminescence (CL) emission of a Co(II)-hydrogen peroxide-sodium hydroxide system. The enhanced CL emission was attributed to the large specific surface area of Mg-Al CO3-LDHs, which facilitates the generation of an excited-stated intermediate. The proposed method displayed high selectivity toward Co(II) over other metal ions. Under the optimal conditions, the increased CL intensity showed a linear response versus Co(II) concentration in the range of 5.0-1000 nM with a detection limit of 3.7 nM (S/N = 3). The relative standard deviation for nine repeated measurements of 100 nM Co(II) was 3.2%. Furthermore, the proposed method was successfully applied to detect Co(II) in living cell samples, and the results were agreed with those obtained by the standard ICP-MS method.

Parametrization of a force field for metals complexed to biomacromolecules: applications to Fe(II), Cu(II) and Pb(II)

NASA Astrophysics Data System (ADS)

David, Laurent; Amara, Patricia; Field, Martin J.; Major, François

2002-08-01

Although techniques for the simulation of biomolecules, such as proteins and RNAs, have greatly advanced in the last decade, modeling complexes of biomolecules with metal ions remains problematic. Precise calculations can be done with quantum mechanical methods but these are prohibitive for systems the size of macromolecules. More qualitative modeling can be done with molecular mechanical potentials but the parametrization of force fields for metals is often difficult, particularly if the bonding between the metal and the groups in its coordination shell has significant covalent character. In this paper we present a method for deriving bond and bond-angle parameters for metal complexes from experimental bond and bond-angle distributions obtained from the Cambridge Structural Database. In conjunction with this method, we also introduce a non-standard energy term of gaussian form that allows us to obtain a stable description of the coordination about a metal center during a simulation. The method was evaluated on Fe(II)-porphyrin complexes, on simple Cu(II) ion complexes and a number of complexes of the Pb(II) ion.

Hypothesis testing for the validation of the kinetic spectrophotometric methods for the determination of lansoprazole in bulk and drug formulations via Fe(III) and Zn(II) chelates.

PubMed

Rahman, Nafisur; Kashif, Mohammad

2010-03-01

Point and interval hypothesis tests performed to validate two simple and economical, kinetic spectrophotometric methods for the assay of lansoprazole are described. The methods are based on the formation of chelate complex of the drug with Fe(III) and Zn(II). The reaction is followed spectrophotometrically by measuring the rate of change of absorbance of coloured chelates of the drug with Fe(III) and Zn(II) at 445 and 510 nm, respectively. The stoichiometric ratio of lansoprazole to Fe(III) and Zn(II) complexes were found to be 1:1 and 2:1, respectively. The initial-rate and fixed-time methods are adopted for determination of drug concentrations. The calibration graphs are linear in the range 50-200 µg ml⁻¹ (initial-rate method), 20-180 µg ml⁻¹ (fixed-time method) for lansoprazole-Fe(III) complex and 120-300 (initial-rate method), and 90-210 µg ml⁻¹ (fixed-time method) for lansoprazole-Zn(II) complex. The inter-day and intra-day precision data showed good accuracy and precision of the proposed procedure for analysis of lansoprazole. The point and interval hypothesis tests indicate that the proposed procedures are not biased. Copyright © 2010 John Wiley & Sons, Ltd.

Synthesis, characterization and physicochemical studies of new chelating resin 1, 8-(3, 6-dithiaoctyl)-4-polyvinylbenzenesulphonate (dpvbs) and its metallopolymer Cu(II), Ni(II), Co(II) and Fe(III) complexes

NASA Astrophysics Data System (ADS)

Khalil, Tarek E.; Elbadawy, Hemmat A.; El-Dissouky, Ali

2018-02-01

A new chelating resin, 1,8-(3,6-dithiaoctyl)-4-polyvinylbenzenesulphonate (dpvbs) has been synthesized by coupling Amberlite XAD-16 with (2,2‧-ethylenedithio) diethanol using pyridine/CH2Cl2 mixture as a solvent. The chelating resin and its metallopolymer Cu(II), Ni(II), Co(II) and Fe(III) complexes have been synthesized and characterized by EDS, SEM, XPS, elemental analysis, spectral (IR, UV/Vis, EPR). The thermal analysis of the resin and its metallopolymer complexes indicated an endothermic spontaneous sorption mechanism with the liberation of water of hydration of the metal ions and that adsorbed by the free resin. At the solid liquid interface, the degrees of freedom increased during the sorption of the metal ions onto the resin. The surface area of polymer support and its metallopolymer complexes are estimated by (BJH) method. The batch equilibrium method was used for studying the metal sorption and selectivity at different pH values and different contact times at room temperature. ICP-AES was used to estimate the metal capacity of the resin for sorption of Cu(II), Ni(II), Co(II) and Fe(III) from aqueous solutions utilizing the batch equilibrium method. The sorption tendency of the metal ions by the resin was found to be: Cu(II) > Fe(III) > Co(II) > Ni(II). Adsorption kinetics was found to be fit the pseudo-second order model.

Rational Clinical Experiment: Assessing Prior Probability and Its Impact on the Success of Phase II Clinical Trials

PubMed Central

Halperin, Daniel M.; Lee, J. Jack; Dagohoy, Cecile Gonzales; Yao, James C.

2015-01-01

Purpose Despite a robust clinical trial enterprise and encouraging phase II results, the vast minority of oncologic drugs in development receive regulatory approval. In addition, clinicians occasionally make therapeutic decisions based on phase II data. Therefore, clinicians, investigators, and regulatory agencies require improved understanding of the implications of positive phase II studies. We hypothesized that prior probability of eventual drug approval was significantly different across GI cancers, with substantial ramifications for the predictive value of phase II studies. Methods We conducted a systematic search of phase II studies conducted between 1999 and 2004 and compared studies against US Food and Drug Administration and National Cancer Institute databases of approved indications for drugs tested in those studies. Results In all, 317 phase II trials were identified and followed for a median of 12.5 years. Following completion of phase III studies, eventual new drug application approval rates varied from 0% (zero of 45) in pancreatic adenocarcinoma to 34.8% (24 of 69) for colon adenocarcinoma. The proportion of drugs eventually approved was correlated with the disease under study (P < .001). The median type I error for all published trials was 0.05, and the median type II error was 0.1, with minimal variation. By using the observed median type I error for each disease, phase II studies have positive predictive values ranging from less than 1% to 90%, depending on primary site of the cancer. Conclusion Phase II trials in different GI malignancies have distinct prior probabilities of drug approval, yielding quantitatively and qualitatively different predictive values with similar statistical designs. Incorporation of prior probability into trial design may allow for more effective design and interpretation of phase II studies. PMID:26261263

Thermodynamic controls on the kinetics of microbial low-pH Fe(II) oxidation.

PubMed

Larson, Lance N; Sánchez-España, Javier; Kaley, Bradley; Sheng, Yizhi; Bibby, Kyle; Burgos, William D

2014-08-19

Acid mine drainage (AMD) is a major worldwide environmental threat to surface and groundwater quality. Microbial low-pH Fe(II) oxidation could be exploited for cost-effective AMD treatment; however, its use is limited because of uncertainties associated with its rate and ability to remove Fe from solution. We developed a thermodynamic-based framework to evaluate the kinetics of low-pH Fe(II) oxidation. We measured the kinetics of low-pH Fe(II) oxidation at five sites in the Appalachian Coal Basin in the US and three sites in the Iberian Pyrite Belt in Spain and found that the fastest rates of Fe(II) oxidation occurred at the sites with the lowest pH values. Thermodynamic calculations showed that the Gibbs free energy of Fe(II) oxidation (ΔG(oxidation)) was also most negative at the sites with the lowest pH values. We then conducted two series of microbial Fe(II) oxidation experiments in laboratory-scale chemostatic bioreactors operated through a series of pH values (2.1-4.2) and found the same relationships between Fe(II) oxidation kinetics, ΔG(oxidation), and pH. Conditions that favored the fastest rates of Fe(II) oxidation coincided with higher Fe(III) solubility. The solubility of Fe(III) minerals, thus plays an important role on Fe(II) oxidation kinetics. Methods to incorporate microbial low-pH Fe(II) oxidation into active and passive AMD treatment systems are discussed in the context of these findings. This study presents a simplified model that describes the relationship between free energy and microbial kinetics and should be broadly applicable to many biogeochemical systems.

Innovation processes in technologies for the processing of refractory mineral raw materials

NASA Astrophysics Data System (ADS)

Chanturiya, V. A.

2008-12-01

Analysis of the grade of mineral resources of Russia and other countries shows that end products that are competitive in terms of both technological and environmental criteria in the world market can only be obtained by the development and implementation of progressive technologies based on the up-to-date achievements of fundamental sciences. The essence of modern innovation processes in technologies developed in Russia for the complex and comprehensive processing of refractory raw materials with a complex composition is ascertained. These processes include (i) radiometric methods of concentration of valuable components, (ii) high-energy methods of disintegration of highly dispersed mineral components, and (iii) electrochemical methods of water conditioning to obtain target products for solving specific technological problems.

Computation of Anisotropic Bi-Material Interfacial Fracture Parameters and Delamination Creteria

NASA Technical Reports Server (NTRS)

Chow, W-T.; Wang, L.; Atluri, S. N.

1998-01-01

This report documents the recent developments in methodologies for the evaluation of the integrity and durability of composite structures, including i) the establishment of a stress-intensity-factor based fracture criterion for bimaterial interfacial cracks in anisotropic materials (see Sec. 2); ii) the development of a virtual crack closure integral method for the evaluation of the mixed-mode stress intensity factors for a bimaterial interfacial crack (see Sec. 3). Analytical and numerical results show that the proposed fracture criterion is a better fracture criterion than the total energy release rate criterion in the characterization of the bimaterial interfacial cracks. The proposed virtual crack closure integral method is an efficient and accurate numerical method for the evaluation of mixed-mode stress intensity factors.

Numerical computation of gravitational field for general axisymmetric objects

NASA Astrophysics Data System (ADS)

Fukushima, Toshio

2016-10-01

We developed a numerical method to compute the gravitational field of a general axisymmetric object. The method (I) numerically evaluates a double integral of the ring potential by the split quadrature method using the double exponential rules, and (II) derives the acceleration vector by numerically differentiating the numerically integrated potential by Ridder's algorithm. Numerical comparison with the analytical solutions for a finite uniform spheroid and an infinitely extended object of the Miyamoto-Nagai density distribution confirmed the 13- and 11-digit accuracy of the potential and the acceleration vector computed by the method, respectively. By using the method, we present the gravitational potential contour map and/or the rotation curve of various axisymmetric objects: (I) finite uniform objects covering rhombic spindles and circular toroids, (II) infinitely extended spheroids including Sérsic and Navarro-Frenk-White spheroids, and (III) other axisymmetric objects such as an X/peanut-shaped object like NGC 128, a power-law disc with a central hole like the protoplanetary disc of TW Hya, and a tear-drop-shaped toroid like an axisymmetric equilibrium solution of plasma charge distribution in an International Thermonuclear Experimental Reactor-like tokamak. The method is directly applicable to the electrostatic field and will be easily extended for the magnetostatic field. The FORTRAN 90 programs of the new method and some test results are electronically available.

Computational tools and lattice design for the PEP-II B-Factory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cai, Y.; Irwin, J.; Nosochkov, Y.

1997-02-01

Several accelerator codes were used to design the PEP-II lattices, ranging from matrix-based codes, such as MAD and DIMAD, to symplectic-integrator codes, such as TRACY and DESPOT. In addition to element-by-element tracking, we constructed maps to determine aberration strengths. Furthermore, we have developed a fast and reliable method (nPB tracking) to track particles with a one-turn map. This new technique allows us to evaluate performance of the lattices on the entire tune-plane. Recently, we designed and implemented an object-oriented code in C++ called LEGO which integrates and expands upon TRACY and DESPOT. {copyright} {ital 1997 American Institute of Physics.}

Computational tools and lattice design for the PEP-II B-Factory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cai Yunhai; Irwin, John; Nosochkov, Yuri

1997-02-01

Several accelerator codes were used to design the PEP-II lattices, ranging from matrix-based codes, such as MAD and DIMAD, to symplectic-integrator codes, such as TRACY and DESPOT. In addition to element-by-element tracking, we constructed maps to determine aberration strengths. Furthermore, we have developed a fast and reliable method (nPB tracking) to track particles with a one-turn map. This new technique allows us to evaluate performance of the lattices on the entire tune-plane. Recently, we designed and implemented an object-oriented code in C++ called LEGO which integrates and expands upon TRACY and DESPOT.

Overview of Optical and Thermal Laser-Tissue Interaction and Nomenclature

NASA Astrophysics Data System (ADS)

Welch, Ashley J.; van Gemert, Martin J. C.

The development of a unified theory for the optical and thermal response of tissue to laser radiation is no longer in its infancy, though it is still not fully developed. This book describes our current understanding of the physical events that can occur when light interacts with tissue, particularly the sequence of formulations that estimate the optical and thermal responses of tissue to laser radiation. This overview is followed by an important chapter that describes the basic interactions of light with tissue. Part I considers basic tissue optics. Tissue is treated as an absorbing and scattering medium and methods are presented for calculating and measuring light propagation, including polarized light. Also, methods for estimating tissue optical properties from measurements of reflection and transmission are discussed. Part II concerns the thermal response of tissue owing to absorbed light, and rate reactions are presented for predicting the extent of laser induced thermal damage. Methods for measuring temperature, thermal properties, rate constants, pulsed ablation and laser tissue interactions are detailed. Part III is devoted to examples that use the theory presented in Parts I and II to analyze various medical applications of lasers. Discussions of Optical Coherence Tomography (OCT), forensic optics, and light stimulation of nerves are also included.

Preferred crystallographic orientation in the ice I ← II transformation and the flow of ice II

USGS Publications Warehouse

Bennett, K.; Wenk, H.-R.; Durham, W.B.; Stern, L.A.; Kirby, S.H.

1997-01-01

The preferred crystallographic orientation developed during the ice I ← II transformation and during the plastic flow of ice II was measured in polycrystalline deuterium oxide (D2O) specimens using low-temperature neutron diffraction. Samples partially transformed from ice I to II under a non-hydrostatic stress developed a preferred crystallographic orientation in the ice II. Samples of pure ice II transformed from ice I under a hydrostatic stress and then when compressed axially, developed a strong preferred orientation of compression axes parallel to (1010). A match to the observed preferred orientation using the viscoplastic self-consistent theory was obtained only when (1010) [0001] was taken as the predominant slip system in ice II.

Extraction of tocopherolquinone from commercially produced vegetable oil waste and its regeneration back to vitamin E

NASA Astrophysics Data System (ADS)

Bayala, Isso

Vegetable oils are the most important natural source of vitamin E in the human diet. These oils are refined in order to eliminate impurities and undesirable substances that may affect the taste or cause health risks. While the goal of the refinery is to improve the quality of certain organoleptic parameters such as odors, it also has some negative impacts on the content and stability of the micronutrients such as tocopherols and tocotrienols. Synthetic vitamin E now manufactured as all-racemic alpha tocopheryl acetate is usually marked as d, l-tocopherol or d, l-tocopheryl acetate with no known side effects, but has been proven to be less active than its natural form. Naturopathic and orthomolecular medicine advocates consider the synthetic vitamin E forms to offer little or no benefit for cancer, circulatory and heart diseases. The market for vitamin E has been growing since the year 2000 causing a gradual rise in pricing because of the shortage in supplies. On a geographical basis North America constitutes the largest consumer on the planet with 50 % of the synthetic vitamin E world market followed by Europe with 25 % and Latin America and Asia Pacific sharing equally the remaining balance. In response to the shortfall, several companies are modifying their operations by rationalizing their older facilities while upgrading technology and adding capacity to meet the demand. But this response has also its downside with companies obligated to meet tough environmental regulations. The purpose of the present dissertation was to develop a method that can help industries involved in vitamin E production maximize their productivity by transforming some of the waste products to vitamin E. To that end, a cost effective simple method was developed in chapter II using tin (II) to regenerate tocopherolquinone back to vitamin E. Chapter II also concerns a method developed to reduce tocopherolquinone back to vitamin E but this time using the chemical species chromium (III). Finally, chapter III covers an extraction method that is more than 95% efficient in removing the tocopherolquinone from the oil waste prior to the reduction process.

Energy landscapes in proteins and glasses

NASA Astrophysics Data System (ADS)

Singh, Sadanand

Soft materials are ubiquitous in our day-to-day life. They include liquids, colloids, polymers, foams, gels, granular systems, and a number of biological materials. While these materials exhibit a wide range of textures and morphologies, many of their properties have common physicochemical origins. A better understanding of such origins would lead to rational design and engineering of functional soft materials. A common feature of soft materials is the wide range of time and length scales that characterizes their behavior. Unfortunately, available molecular modeling techniques are often ill-suited for problems that exhibit multiple length and time scales. In this thesis, we introduce and implement new simulation methods that have enabled molecular-level studies of soft materials. Such methods permit calculation of free energy surfaces, and we demonstrate their usefulness in the context of proteins and glasses, both of which exhibit rugged free energy landscapes. A first application is concerned with human amylin, a protein associated with Type II diabetes. Patients with Type II diabetes exhibit fibrillar deposits of human amylin protein in the pancreas. By applying the advanced simulation methods and algorithms developed in this work, we investigate the structure and folding dynamics of human amylin. A detailed mechanism is presented at the atomic-level for the nucleation and aggregation of the peptide. The results presented in this work could help in development of therapeutic strategies for Type II diabetes. The second application is concerned with the study of vapor-deposited ultrastable glasses. These stable glasses have, far below the conventional glass transition temperature, the properties expected from the equilibrium supercooled liquid state. Our results indicate that optimal stability is attained when deposition occurs near the Kauzmann temperature. We also show that the extraordinary stability of model vapor deposited glasses is associated with distinct structural motifs.

A Computer-Adaptive Disability Instrument for Lower Extremity Osteoarthritis Research Demonstrated Promising Breadth, Precision and Reliability

PubMed Central

Jette, Alan M.; McDonough, Christine M.; Haley, Stephen M.; Ni, Pengsheng; Olarsch, Sippy; Latham, Nancy; Hambleton, Ronald K.; Felson, David; Kim, Young-jo; Hunter, David

2012-01-01

Objective To develop and evaluate a prototype measure (OA-DISABILITY-CAT) for osteoarthritis research using Item Response Theory (IRT) and Computer Adaptive Test (CAT) methodologies. Study Design and Setting We constructed an item bank consisting of 33 activities commonly affected by lower extremity (LE) osteoarthritis. A sample of 323 adults with LE osteoarthritis reported their degree of limitation in performing everyday activities and completed the Health Assessment Questionnaire-II (HAQ-II). We used confirmatory factor analyses to assess scale unidimensionality and IRT methods to calibrate the items and examine the fit of the data. Using CAT simulation analyses, we examined the performance of OA-DISABILITY-CATs of different lengths compared to the full item bank and the HAQ-II. Results One distinct disability domain was identified. The 10-item OA-DISABILITY-CAT demonstrated a high degree of accuracy compared with the full item bank (r=0.99). The item bank and the HAQ-II scales covered a similar estimated scoring range. In terms of reliability, 95% of OA-DISABILITY reliability estimates were over 0.83 versus 0.60 for the HAQ-II. Except at the highest scores the 10-item OA-DISABILITY-CAT demonstrated superior precision to the HAQ-II. Conclusion The prototype OA-DISABILITY-CAT demonstrated promising measurement properties compared to the HAQ-II, and is recommended for use in LE osteoarthritis research. PMID:19216052

Determination of ferrous and total iron in refractory spinels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Amonette, James E.; Matyas, Josef

2015-12-30

Accurate and precise determination of the redox state of iron (Fe) in spinels presents a significant challenge due to their refractory nature. The resultant extreme conditions needed to obtain complete dissolution generally oxidize some of the Fe(II) initially present and thus prevent the use of colorimetric methods for Fe(II) measurements. To overcome this challenge we developed a hybrid oxidimetric/colorimetric approach, using Ag(I) as the oxidimetric reagent for determination of Fe(II) and 1,10-phenanthroline as the colorimetric reagent for determination of total Fe. This approach, which allows determination of Fe(II) and total Fe on the same sample, was tested on a seriesmore » of four geochemical reference materials and then applied to the analysis of Fe(Ni) spinel crystals isolated from simulated high-level-waste (HLW) glass and of several reagent magnetites. Results for the reference materials were in excellent agreement with published values, with the exception of USGS BIR-1, for which higher Fe(II) values and lower total Fe values were obtained. The Fe(Ni) spinels showed Fe(II) values at the detection limit (ca. 0.05 wt% Fe) and total Fe values slightly higher than obtained by total elemental analysis. For the magnetite samples, total Fe values were in agreement with reference results, but a wide range in Fe(II) values was obtained indicating various degrees of conversion to maghemite.« less

Fast spacecraft adaptive attitude tracking control through immersion and invariance design

NASA Astrophysics Data System (ADS)

Wen, Haowei; Yue, Xiaokui; Li, Peng; Yuan, Jianping

2017-10-01

This paper presents a novel non-certainty-equivalence adaptive control method for the attitude tracking control problem of spacecraft with inertia uncertainties. The proposed immersion and invariance (I&I) based adaptation law provides a more direct and flexible approach to circumvent the limitations of the basic I&I method without employing any filter signal. By virtue of the adaptation high-gain equivalence property derived from the proposed adaptive method, the closed-loop adaptive system with a low adaptation gain could recover the high adaptation gain performance of the filter-based I&I method, and the resulting control torque demands during the initial transient has been significantly reduced. A special feature of this method is that the convergence of the parameter estimation error has been observably improved by utilizing an adaptation gain matrix instead of a single adaptation gain value. Numerical simulations are presented to highlight the various benefits of the proposed method compared with the certainty-equivalence-based control method and filter-based I&I control schemes.

AWIPS II Application Development, a SPoRT Perspective

NASA Technical Reports Server (NTRS)

Burks, Jason E.; Smith, Matthew; McGrath, Kevin M.

2014-01-01

The National Weather Service (NWS) is deploying its next-generation decision support system, called AWIPS II (Advanced Weather Interactive Processing System II). NASA's Short-term Prediction Research and Transition (SPoRT) Center has developed several software 'plug-ins' to extend the capabilities of AWIPS II. SPoRT aims to continue its mission of improving short-term forecasts by providing NASA and NOAA products on the decision support system used at NWS weather forecast offices (WFOs). These products are not included in the standard Satellite Broadcast Network feed provided to WFOs. SPoRT has had success in providing support to WFOs as they have transitioned to AWIPS II. Specific examples of transitioning SPoRT plug-ins to WFOs with newly deployed AWIPS II systems will be presented. Proving Ground activities (GOES-R and JPSS) will dominate SPoRT's future AWIPS II activities, including tool development as well as enhancements to existing products. In early 2012 SPoRT initiated the Experimental Product Development Team, a group of AWIPS II developers from several institutions supporting NWS forecasters with innovative products. The results of the team's spring and fall 2013 meeting will be presented. Since AWIPS II developers now include employees at WFOs, as well as many other institutions related to weather forecasting, the NWS has dealt with a multitude of software governance issues related to the difficulties of multiple remotely collaborating software developers. This presentation will provide additional examples of Research-to-Operations plugins, as well as an update on how governance issues are being handled in the AWIPS II developer community.

Anticancer, antibacterial and antifungal activity of new ni (ii) and cu (ii) complexes of imidazole-phenanthroline derivatives.

PubMed

Moghadam, Mahboube Eslami; Divsalar, Adeleh; Zare, Marziye Shahraki; Gholizadeh, Roghayeh; Mahalleh, Doran; Saghatforosh, Lotfali; Sanati, Soheila

2017-11-02

Two new nickel(II) and copper(II) complexes of 2-(Furan-2-yl)-1H-Imidazo[4,5-f][1,10]Phenanthroline (FIP) and 2-(thiophen-2-yl)-1H-imidazo[4,5-f][1,10]phenanthroline (TIP), imidazophen derivatives were synthesized. The structures of the compounds were determined by UV-visible and FT-IR spectroscopic methods and elemental analysis. The biological activities of Ni and Cu complexes, as anticancer agents, were tested against chronic myelogenous leukemia cell line, K562, at micromolar concentration. The MTT studies showed Cc 50 values are 21 and 160 µM for Cu and Ni(II) complexes, respectively; suggesting that Ni (II) complex has Cc 50 almost seven times of that obtained for cisplatin. Biological activity of the Ni(II) and Cu(II) complexes were also assayed against selective microorganisms by disc diffusion method. These results showed that the Cu(II) complex is antifungal agent but Ni(II) complex has antibacterial activity.

Magnetic separation of heavy metal ions and evaluation based on surface-enhanced Raman spectroscopy: copper(II) ions as a case study.

PubMed

Yan, Xue; Zhang, Xue-Jiao; Yuan, Ya-Xian; Han, San-Yang; Xu, Min-Min; Gu, Ren'ao; Yao, Jian-Lin

2013-11-01

A new approach was developed for the magnetic separation of copper(II) ions with easy operation and high efficiency. p-Mercaptobenzoic acid served as the modified tag of Fe2O3@Au nanoparticles both for the chelation ligand and Raman reporter. Through the chelation between the copper(II) ions and carboxyl groups on the gold shell, the Fe2O3@Au nanoparticles aggregated to form networks that were enriched and separated from the solution by a magnet. A significant decrease in the concentration of copper(II) ions in the supernatant solution was observed. An extremely sensitive method based on surface-enhanced Raman spectroscopy was employed to detect free copper(II) ions that remained after the magnetic separation, and thus to evaluate the separation efficiency. The results indicated the intensities of the surface-enhanced Raman spectroscopy bands from p-mercaptobenzoic acid were dependent on the concentration of copper(II) ions, and the concentration was decreased by several orders of magnitude after the magnetic separation. The present protocol effectively decreased the total amount of heavy metal ions in the solution. This approach opens a potential application in the magnetic separation and highly sensitive detection of heavy metal ions. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The use of macroalgae (Gracilaria changii) as bio-adsorbent for Copper (II) removal

NASA Astrophysics Data System (ADS)

Lavania-Baloo; Idayu, Nordin; Umar Salihi, Ibrahim; Zainoddin, Jamari

2017-05-01

Biosorption of heavy metals using marine macroalgae biomass can be an effective process and alternative to conventional methods. Activated carbon was developed from macroalgae (Gracilaria changii) and used as adsorbents for the removal of copper (II) from wastewater. Gracilaria changii based activated carbon (GCBAC) was prepared using muffle furnace at a constant temperature of 300 °C for 1 hour. Batch adsorption experiments were conducted to investigate the effets of important parameters such as pH, contact time, initial metal concentration and adsorbent dosage on the removal of Cu (II) from synthetic aqueous solution. Batch adsorption study shows that removal of Cu (II) using GCBAC relied upon pH, contact time, initial metal concentration and GCBAC dosage. The optimum conditions parameters were found to be pH 6.0, time of 60 minutes and GCBAC dosage of 0.3 g, respectively. Adsorption data was described better by Freundlich isotherm model with R2 value of 0.7936. The maximum Cu (II) adsorption capacity of GCBAC was found to be 0.07 mg/g. The experimental adsorption data obtained fitted well into Pseudo-second-order kinetic model, with R2 value near unity. Thus, GCBAC can be used as an effective adsorbent for the removal of Cu (II) from aqueous solution.

Carbon dots-based fluorescent probe for "off-on" sensing of Hg(II) and I⁻.

PubMed

He, Jiangling; Zhang, Haoran; Zou, Jinliang; Liu, Yingliang; Zhuang, Jianle; Xiao, Yong; Lei, Bingfu

2016-05-15

Herein, we report a simple, one-step reflux method for synthesis of photoluminescent carbon dots (CDs) using citric acid as the carbon source and diethylenetriamine (DETA) as the surface passivation reagent along with a high quantum yield (82.40%), the fluorescence intensity of the CDs was found to be effectively quenched by Hg(II) ions. Upon addition of I(-) to the CDs/Hg(II) complex dispersion, the fluorescence intensity of the CDs was significantly recovered. Furthermore, we developed an "off-on" fluorescence assay for the detection of I(-) using CDs/Hg(II) as a fluorescence probe. This probe enables the selective detection of Hg(II) with a linear range of 0-80 μM and a limit of detection is 0.201 µM and a limit of detection about I(-) is 0.234 µM with a linear range of 0-70 μM. Most importantly, the sensors can be successfully applied to the determination of Hg(II) and I(-) in real lake water and urine of cattles, the "off-on" sensor demonstrates high selectivity, repeatability, stability, which offer this CDs-based "off-on" fluorescent sensor a promising platform for environmental and biological sensing applications. Copyright © 2015 Elsevier B.V. All rights reserved.

A simple and low cost dual-wavelength β-correction spectrophotometric determination and speciation of mercury(II) in water using chromogenic reagent 4-(2-thiazolylazo) resorcinol

NASA Astrophysics Data System (ADS)

Al-Bagawi, A. H.; Ahmad, W.; Saigl, Z. M.; Alwael, H.; Al-Harbi, E. A.; El-Shahawi, M. S.

2017-12-01

The most common problems in spectrophotometric determination of various complex species originate from the background spectral interference. Thus, the present study aimed to overcome the spectral matrix interference for the precise analysis and speciation of mercury(II) in water by dual-wavelength β-correction spectrophotometry using 4-(2-thiazolylazo) resorcinol (TAR) as chromogenic reagent. The principle was based on measuring the correct absorbance for the formed complex of mercury(II) ions with TAR reagent at 547 nm (lambda max). Under optimized conditions, a linear dynamic range of 0.1-2.0 μg mL- 1 with correlation coefficient (R2) of 0.997 were obtained with lower limits of detection (LOD) of 0.024 μg mL- 1 and limit of quantification (LOQ) of 0.081 μg mL- 1. The values of RSD and relative error (RE) obtained for β-correction method and single wavelength spectrophotometry were 1.3, 1.32% and 4.7, 5.9%, respectively. The method was validated in tap and sea water in terms of the data obtained from inductively coupled plasma-optical emission spectrometry (ICP-OES) using student's t and F tests. The developed methodology satisfactorily overcomes the spectral interference in trace determination and speciation of mercury(II) ions in water.

Flow injection chemiluminescence determination of vitamin B12 using on-line UV-persulfate photooxidation and charge coupled device detection.

PubMed

Murillo Pulgarín, José A; García Bermejo, Luisa F; Sánchez García, M Nieves

2011-01-01

A sensitive chemiluminescence method for vitamin B(12) using a charge-coupled device (CCD) photodetector combined with on-line UV-persulfate oxidation in a simple continuous flow system has been developed. The principle for the determination of vitamin B(12) is based on the enhancive effect of cobalt (II) on the chemiluminescence reaction between luminol and percarbonate in alkaline medium. In addition, percarbonate has been investigated and proposed as a powerful source of hydrogen peroxide as oxidant agent in this chemiluminescence reaction. The digestion of vitamin B(12) to release the cobalt (II) is reached by UV irradiation treatment in a persulfate medium. The CCD detector, directly connected to the flow cell, is used with the continuous flow manifold to obtain the full spectral characteristics of cobalt (II) catalyzed luminol-percarbonate reaction. The vitamin B(12) oxidation process and chemical conditions for the chemiluminescence reaction were investigated and optimized. The increment of the emission intensity was proportional to the concentration of vitamin B(12) , giving a second-order calibration graph over the cobalt (II) concentration range from 10 to 5000 μg L(-1)(r(2) = 0.9985) with a detection limit of 9.3 μg L(-1). The proposed method was applied to the determination of vitamin B(12) in different kinds of pharmaceuticals. Copyright © 2011 John Wiley & Sons, Ltd.

Sensitive voltammetric determination of lead released from ceramic dishes by using of bismuth nanostructures anchored on biochar.

PubMed

Agustini, Deonir; Mangrich, Antonio Salvio; Bergamini, Márcio F; Marcolino-Junior, Luiz Humberto

2015-09-01

A simple and sensitive electroanalytical method was developed for determination of nanomolar levels of Pb(II) based on the voltammetric stripping response at a carbon paste electrode modified with biochar (a special charcoal) and bismuth nanostructures (nBi-BchCPE). The proposed methodology was based on spontaneous interactions between the highly functionalized biochar surface and Pb(II) ions followed by reduction of these ions into bismuth nanodots which promote an improvement on the stripping anodic current. The experimental procedure could be summarized in three steps: including an open circuit pre-concentration, reduction of accumulated lead ions at the electrode surface and stripping step under differential pulse voltammetric conditions (DPAdSV). SEM images revealed dimensions of bismuth nanodots ranging from 20 nm to 70 nm. The effects of main parameters related to biochar, bismuth and operational parameters were examined in detail. Under the optimal conditions, the proposed sensor has exhibited linear range from 5.0 to 1000 nmol L(-1) and detection limit of 1.41 nmol L(-1) for Pb(II). The optimized method was successfully applied for determination of Pb(II) released from overglaze-decorated ceramic dishes. Results obtained were compared with those given by inductively coupled plasma optical emission spectroscopy (ICP-OES) and they are in agreement at 99% of confidence level. Copyright © 2015. Published by Elsevier B.V.

Treatment of geometric singularities in implicit solvent models

NASA Astrophysics Data System (ADS)

Yu, Sining; Geng, Weihua; Wei, G. W.

2007-06-01

Geometric singularities, such as cusps and self-intersecting surfaces, are major obstacles to the accuracy, convergence, and stability of the numerical solution of the Poisson-Boltzmann (PB) equation. In earlier work, an interface technique based PB solver was developed using the matched interface and boundary (MIB) method, which explicitly enforces the flux jump condition at the solvent-solute interfaces and leads to highly accurate biomolecular electrostatics in continuum electric environments. However, such a PB solver, denoted as MIBPB-I, cannot maintain the designed second order convergence whenever there are geometric singularities, such as cusps and self-intersecting surfaces. Moreover, the matrix of the MIBPB-I is not optimally symmetrical, resulting in the convergence difficulty. The present work presents a new interface method based PB solver, denoted as MIBPB-II, to address the aforementioned problems. The present MIBPB-II solver is systematical and robust in treating geometric singularities and delivers second order convergence for arbitrarily complex molecular surfaces of proteins. A new procedure is introduced to make the MIBPB-II matrix optimally symmetrical and diagonally dominant. The MIBPB-II solver is extensively validated by the molecular surfaces of few-atom systems and a set of 24 proteins. Converged electrostatic potentials and solvation free energies are obtained at a coarse grid spacing of 0.5Å and are considerably more accurate than those obtained by the PBEQ and the APBS at finer grid spacings.

Enrichment and purification of six Aconitum alkaloids from Aconiti kusnezoffii radix by macroporous resins and quantification by HPLC-MS.

PubMed

Liu, Jingjing; Li, Qing; Liu, Ran; Yin, Yidi; Chen, Xiaohui; Bi, Kaishun

2014-06-01

Aconitine, mesaconitine, hypaconitine, benzoylaconine, benzoylmesaconine and benzoylhypaconine are six main Aconitum alkaloids from traditional Chinese medicine, Aconiti kusnezoffii radix, which possess highly bioactive as well as highly toxic character for medicinal use. In the present study, for the purpose of better utilizing the toxic herbal material, the performance characteristics of NKA-II, D101, X-5, AB-8, S-8, HPD722 and HPD750 macroporous resins for the enrichment and purification of these six Aconitum alkaloids were critically evaluated. Results showed that NKA-II offered the best adsorption and desorption capacities for six Aconitum alkaloids among the seven macroporous resins tested, which were affected significantly by the pH value. Subsequently, dynamic adsorption and desorption experiments had been carried out with the column packed by NKA-II resin to optimize the separation process of six Aconitum alkaloids. After one run treatment with NKA-II resin, the content of total six Aconitum alkaloids were increased from 5.87% to 60.3%, the recovery was 75.8%. Meanwhile, a validated HPLC-MS method had been developed to qualitative and quantitative these six Aconitum alkaloids. This method would provide scientific references to the large-scale production of six Aconitum alkaloids from Aconiti kusnezoffii radix or other plants and might also expand the secure application of these highly toxic components for pharmacy. Copyright © 2014 Elsevier B.V. All rights reserved.

Enzymatic conversion of pretreated biomass into fermentable sugars for biorefinery operation

NASA Astrophysics Data System (ADS)

Gao, Dahai

2011-12-01

Depleting petroleum reserves and potential climate change caused by fossil fuel consumption have attracted significant attention towards the use of alternative renewable resources for production of fuels and chemicals. Lignocellulosic biomass provides a plentiful resource for the sustainable production of biofuels and biochemicals and could serve as an important contributor to the world energy portfolio in the near future. Successful biological conversion of lignocellulosic biomass requires an efficient and economical pretreatment method, high glucose/xylose yields during enzymatic hydrolysis and fermentation of both hexose and pentose to ethanol. High enzyme loading is a major economic bottleneck for the commercial processing of pretreated lignocellulosic biomass to produce fermentable sugars. Optimizing the enzyme cocktail for specific types of pretreated biomass allows for a significant reduction in enzyme loading without sacrificing hydrolysis yield. Core glycosyl hydrolases were isolated and purified from various sources to help rationally optimize an enzyme cocktail to digest ammonia fiber expansion (AFEX) treated corn stover. The four core cellulases were endoglucanase I (EG I), cellobiohydrolase I (CBH I), cellobiohydrolase II (CBH II) and beta-Glucosidase (betaG). The two core hemicellulases were an endoxylanase (EX) and a beta-xylosidase (betaX). A diverse set of accessory hemicellulases from bacterial sources was found necessary to enhance the synergistic action of cellulases hydrolysing AFEX pretreated corn stover. High glucose (around 80%) and xylose (around 70%) yields were achieved with a moderate enzyme loading (˜20 mg protein/g glucan) using an in-house developed enzyme cocktail and this cocktail was compared to commercial enzyme. Studying the binding properties of cellulases to lignocellulosic substrates is critical to achieving a fundamental understanding of plant cell wall saccharification. Lignin auto-fluorescence and degradation products formed during pretreatment impede accurate quantification of individual glycosyl hydrolases (GH) binding to pretreated cell walls. A high-throughput Fast Protein Liquid Chromatography (HT-FPLC) based method has been developed to quantify CBH I, CBH II and EG I present in hydrolyzates of untreated, AFEX, and dilute-acid pretreated corn stover. This method can accurately quantify individual enzymes present in complex binary and ternary protein mixtures without interference from plant cell wall derived components. The binding characteristics of CBH I, CBH II and EG I during 48 hours hydrolysis were studied on different cellulose allomorphs: microcrystalline cellulose Avicel (cellulose Ibeta), liquid ammonia treated cellulose (cellulose III), sodium hydroxide treated cellulose (cellulose II) and phosphoric acid swollen amorphous cellulose (AC). The digestibility ranking is AC>cellulose III>cellulose II>cellulose I. However, AC has the highest initial enzyme binding capacity while cellulose III had the lowest. CBH II is less stable during hydrolysis. Time course binding studies were also performed for pretreated biomass. Ammonia Fiber Expansion (AFEX) treated corn stover (CS), dilute acid (ACID) treated CS and ionic liquid (IL) pretreated CS were compared. The results indicate that presence of lignin is responsible for significant unproductive cellulase binding. These results are critical for improving our understanding of enzyme synergism, productive/unproductive enzyme binding and the role of pretreatment on enzyme accessibility to lignocellulosic plant cell walls. The results also assist in engineering novel low unproductive binding enzyme systems and developing economic enzyme recycle options.

An efficient hybrid approach for multiobjective optimization of water distribution systems

NASA Astrophysics Data System (ADS)

Zheng, Feifei; Simpson, Angus R.; Zecchin, Aaron C.

2014-05-01

An efficient hybrid approach for the design of water distribution systems (WDSs) with multiple objectives is described in this paper. The objectives are the minimization of the network cost and maximization of the network resilience. A self-adaptive multiobjective differential evolution (SAMODE) algorithm has been developed, in which control parameters are automatically adapted by means of evolution instead of the presetting of fine-tuned parameter values. In the proposed method, a graph algorithm is first used to decompose a looped WDS into a shortest-distance tree (T) or forest, and chords (Ω). The original two-objective optimization problem is then approximated by a series of single-objective optimization problems of the T to be solved by nonlinear programming (NLP), thereby providing an approximate Pareto optimal front for the original whole network. Finally, the solutions at the approximate front are used to seed the SAMODE algorithm to find an improved front for the original entire network. The proposed approach is compared with two other conventional full-search optimization methods (the SAMODE algorithm and the NSGA-II) that seed the initial population with purely random solutions based on three case studies: a benchmark network and two real-world networks with multiple demand loading cases. Results show that (i) the proposed NLP-SAMODE method consistently generates better-quality Pareto fronts than the full-search methods with significantly improved efficiency; and (ii) the proposed SAMODE algorithm (no parameter tuning) exhibits better performance than the NSGA-II with calibrated parameter values in efficiently offering optimal fronts.

Mixed ligand two dimensional Cd(ii)/Ni(ii) metal organic frameworks containing dicarboxylate and tripodal N-donor ligands: Cd(ii) MOF is an efficient luminescent sensor for detection of picric acid in aqueous media.

PubMed

Rachuri, Yadagiri; Parmar, Bhavesh; Bisht, Kamal Kumar; Suresh, Eringathodi

2016-05-04

Two dimensional metal organic frameworks (MOFs) [Cd(5-BrIP)(TIB)]n () and [Ni2(5-BrIP)2(TIB)2]n (), involving the aromatic polycarboxylate ligand 5-bromo isophthalic acid (H2BrIP), flexible tripodal ligand 1,3,5-tris(imidazol-1-ylmethyl)benzene (TIB) and Cd(ii)/Ni(ii) metal nodes have been synthesized by different methods. These compounds were characterized by various analytical methods, and variable temperature X-ray diffraction data showed thermal stability of both MOFs up to 350 °C. Phase purity as well as water stability of the MOFs were established by powder X-ray diffraction, and the structural diversity of the compounds were investigated by single-crystal X-ray diffraction. Both the MOFs are mixed ligand 2D nets, and the topology of the network can be described as a binodal 3,5-c connected net with 3,5L2 topology having the point symbol {4(2)·6(7)·8}{4(2)·6}. Sensing of picric acid [2,4,6-trinitrophenol, TNP] by luminescence quenching among a large range of nitroanalytes in aqueous phase by the Cd(ii) luminescent MOF (LMOF) were been investigated. Structural studies on 1 : 1 co-crystals () of TIB and TNP were carried out. The selective and sensitive fluorescence quenching response of towards electron-deficient TNP over other nitro analytes in aqueous phase was demonstrated by fluorescence quenching titration. Concomitant occurrence of electron transfer/energy transfer processes and electrostatic interaction favours the selective sensing of TNP. A Cd(ii) LMOF ()-coated paper strip that we developed demonstrated fast and selective response to TNP, by the complete quenching of the blue fluorescence upon excitation of the paper strip at 365 nm radiation in its presence.

Development and Validation of New Discriminative Dissolution Method for Carvedilol Tablets

PubMed Central

Raju, V.; Murthy, K. V. R.

2011-01-01

The objective of the present study was to develop and validate a discriminative dissolution method for evaluation of carvedilol tablets. Different conditions such as type of dissolution medium, volume of dissolution medium and rotation speed of paddle were evaluated. The best in vitro dissolution profile was obtained using Apparatus II (paddle), 50 rpm, 900 ml of pH 6.8 phosphate buffer as dissolution medium. The drug release was evaluated by high-performance liquid chromatographic method. The dissolution method was validated according to current ICH and FDA guidelines using parameters such as the specificity, accuracy, precision and stability were evaluated and obtained results were within the acceptable range. The comparison of the obtained dissolution profiles of three different products were investigated using ANOVA-based, model-dependent and model-independent methods, results showed that there is significant difference between the products. The dissolution test developed and validated was adequate for its higher discriminative capacity in differentiating the release characteristics of the products tested and could be applied for development and quality control of carvedilol tablets. PMID:22923865

[Evaluation for anaerobic culture system: Anoxomat Mart II].

PubMed

Kikuchi, Yuji; Sasaki, Hiromi; Furuhata, Yukie; Tazawa, Yoko; Horiuchi, Hajime; Okada, Jun

2007-01-01

Anoxomat Mart II (Mart Microbiology BV, Lichtenvooorde, Netherlands, Central Scientific Commerce Inc., Tokyo, Japan) is an anaerobic jar apparatus which uses a vacuum pump in combination with catalyst as gas replacement procedure to remove all traces of oxygen. As we had a chance to use Anoxomat Mart II, we compared it with other two anaerobic culture methods; namely AnaeroPack anaero (Mitsubishi Gas Chemical Co., Tokyo, Japan) which employs anaerobic jar method, and Concept400 (RUSKINN TECHNOLOGY LTD, England; Central Scientific Commerce INc., Tokyo, Japan) which uses anaerobic chamber method. We used 10 different species of anaerobic bacteria obtained from ATCC. One strain each of 10 species was cultured and examined for measurement of the sensitibity of an anaerobic indicator, th number of bacteria after 48 hour culture, the diameter of colonies, and MIC value. As a result, the time to reach the anaerobic condition was around 30 minutes by the Mart II against around 60 minutes by the AnaeroPack anaero. There was no difference concerning the number of bacteria after 48 hour culture among three methods. But anaerobic bacteria cultured by Mart II tended to make bigger colonies compared to other two methods in the 5 strains out of 9, except for one strain in which the diameter of colonies could not be measured. On the other hand, the comparison of MIC value showed good correlation in 11 antibiotics out of 12 among three methods. The MIC value of 11 antibiotics fitted within 1-fold difference, and 2-fold difference was observed in only one antibiotic. Mart II is so small that it does cheep consumables. From these reasons, we concluded that Mart II can be one of the useful anerobic culture methods.

δ-Similar Elimination to Enhance Search Performance of Multiobjective Evolutionary Algorithms

NASA Astrophysics Data System (ADS)

Aguirre, Hernán; Sato, Masahiko; Tanaka, Kiyoshi

In this paper, we propose δ-similar elimination to improve the search performance of multiobjective evolutionary algorithms in combinatorial optimization problems. This method eliminates similar individuals in objective space to fairly distribute selection among the different regions of the instantaneous Pareto front. We investigate four eliminating methods analyzing their effects using NSGA-II. In addition, we compare the search performance of NSGA-II enhanced by our method and NSGA-II enhanced by controlled elitism.

Zn(II)-coordination modulated ligand photophysical processes – the development of fluorescent indicators for imaging biological Zn(II) ions

PubMed Central

Yuan, Zhao; Simmons, J. Tyler; Sreenath, Kesavapillai

2014-01-01

Molecular photophysics and metal coordination chemistry are the two fundamental pillars that support the development of fluorescent cation indicators. In this article, we describe how Zn(II)-coordination alters various ligand-centered photophysical processes that are pertinent to developing Zn(II) indicators. The main aim is to show how small organic Zn(II) indicators work under the constraints of specific requirements, including Zn(II) detection range, photophysical requirements such as excitation energy and emission color, temporal and spatial resolutions in a heterogeneous intracellular environment, and fluorescence response selectivity between similar cations such as Zn(II) and Cd(II). In the last section, the biological questions that fluorescent Zn(II) indicators help to answer are described, which have been motivating and challenging this field of research. PMID:25071933

Evaluation of phase II toxicity identification evaluation methods for freshwater whole sediment and interstitial water.

PubMed

Phillips, Bryn M; Anderson, Brian S; Hunt, John W; Clark, Sara L; Voorhees, Jennifer P; Tjeerdema, Ron S; Casteline, Jane; Stewart, Margaret

2009-02-01

Phase I whole sediment toxicity identification evaluation (TIE) methods have been developed to characterize the cause of toxicity as organic chemicals, metals, or ammonia. In Phase II identification treatments, resins added to whole sediment to reduce toxicity caused by metals and organics can be separated and eluted much like solid-phase extraction (SPE) columns are eluted for interstitial water. In this study, formulated reference sediments spiked with toxic concentrations of copper, fluoranthene, and nonylphenol were subjected to whole sediment and interstitial water TIE treatments to evaluate Phase I and II TIE procedures for identifying the cause of toxicity to Hyalella azteca. Phase I TIE treatments consisted of adding adsorbent resins to whole sediment, and using SPE columns to remove spiked chemicals from interstitial water. Phase II treatments consisted of eluting resins and SPE columns and the preparation and testing of eluates for toxicity and chemistry. Whole sediment resins and SPE columns significantly reduced toxicity, and the eluates from all treatments contained toxic concentrations of the spiked chemical except for interstitial water fluoranthene. Toxic unit analysis based on median lethal concentrations (LC50s) allowed for the comparison of chemical concentrations among treatments, and demonstrated that the bioavailability of some chemicals was reduced in some samples and treatments. The concentration of fluoranthene in the resin eluate closely approximated the original interstitial water concentration, but the resin eluate concentrations of copper and nonylphenol were much higher than the original interstitial water concentrations. Phase II whole sediment TIE treatments provided complementary lines of evidence to the interstitial water TIE results.

Properties of Type-II ZnTe/ZnSe Submonolayer Quantum Dots Studied via Excitonic Aharonov- Bohm Effect and Polarized Optical Spectroscopy

NASA Astrophysics Data System (ADS)

Ji, Haojie

In this thesis I develop understanding of the fundamental physical and material properties of type-II ZnTe/ZnSe submonolayer quantum dots (QDs), grown via combination of molecular beam epitaxy (MBE) and migration enhanced epitaxy (MEE). I use magneto-photoluminescence, including excitonic Aharonov-Bohm (AB) effect and polarized optical spectroscopy as the primary tools in this work. I present previous studies as well as the background of optical and magneto-optical processes in semiconductor nanostructures and introduce the experimental methods in Chapters 1 - 3. In Chapter 4 I focus on the excitonic AB effect in the type-II QDs. I develop a lateral tightly-bound exciton model for ZnTe/ZnSe type-II QDs, using analytical methods and numerical calculations. This explained the magneto-PL observation and allowed for establishing the size and density of the QDs in each sample based on the results of PL and magneto-PL measurements. For samples with larger QDs, I observe behaviors that fall between properties of quantum-dot and quantum-well-like systems due to increased QD densities and their type-II nature. Finally, the decoherence mechanisms of the AB excitons are investigated via the temperature dependent studies of the magneto-PL. It is determined that the AB exciton decoherence is due to transport-like (acoustic phonon) scattering of the electrons moving in the ZnSe barriers, but with substantially smaller magnitude of electron-phonon coupling constant due to relatively strong electron-hole coupling within these type-II QDs. In Chapter 5 I discuss the results of circularly polarized magneto-PL measurements. A model with ultra-long spin-flip time of holes confined to submonolayer QDs is proposed. The g-factor of type-II excitons was extracted from the Zeeman splitting and the g-factor of electrons was obtained by fitting the temperature dependence of the degree of circular polarization (DCP), from which g-factor of holes confined within ZnTe QDs was found. It is shown that it is about three times larger than that of bulk ZnTe. In Chapter 6 I study the optical anisotropy in QDs. I show that all samples exhibit such an effect, and explain it based on non-spherical shape of the QDs. Numerical calculation is applied to calculate degree of linear polarization, and estimate the aspect ratio. The exciton anisotropic exchange splitting is calculated from the magnetic field dependence of the DCP. In the last two chapters I show my achievement on the growth of ZnO nanorods as a core for type-II 1D systems and propose an outlook for future research on the type-II semiconductor heterostructures.

Comparative Study of Hand-Sutured versus Circular Stapled Anastomosis for Gastrojejunostomy in Laparoscopy Assisted Distal Gastrectomy.

PubMed

Seo, Su Hyun; Kim, Ki Han; Kim, Min Chan; Choi, Hong Jo; Jung, Ghap Joong

2012-06-01

Mechanical stapler is regarded as a good alternative to the hand sewing technique, when used in gastric reconstruction. The circular stapling method has been widely applied to gastrectomy (open orlaparoscopic), for gastric cancer. We illustrated and compared the hand-sutured method to the circular stapling method, for Billroth-II, in patients who underwent laparoscopy assisted distal gastrectomy for gastric cancer. Between April 2009 and May 2011, 60 patients who underwent laparoscopy assisted distal gastrectomy, with Billroth-II, were enrolled. Hand-sutured Billroth-II was performed in 40 patients (manual group) and circular stapler Billroth-II was performed in 20 patients (stapler group). Clinicopathological features and post-operative outcomes were evaluated and compared between the two groups. Nosignificant differences were observed in clinicopathologic parameters and post-operative outcomes, except in the operation times. Operation times and anastomosis times were significantly shorter in the stapler group (P=0.004 and P<0.001). Compared to the hand-sutured method, the circular stapling method can be applied safely and more efficiently, when performing Billroth-II anastomosis, after laparoscopy assisted distal gastrectomy in patients with gastric cancer.

Rapid detection of protein phosphatase activity using Zn(II)-coordinated gold nanosensors based on His-tagged phosphopeptides.

PubMed

Lee, Jin Oh; Kim, Eun-Ji; Lim, Butaek; Kim, Tae-Wuk; Kim, Young-Pil

2015-01-20

We report a rapid colorimetric assay to detect protein phosphatase (PP) activity based on the controlled assembly and disassembly of gold nanoparticles (AuNPs) via Zn(II)-specific coordination in the presence of His6-tagged phosphopeptides. Among divalent metal ions including Ni(II), Cu(II), Co(II), Mg(II), Mn(II), and Zn(II), only Zn(II) triggered a strong association between phosphopeptides with hexahistidine at a single end and nitrilotriacetic acid (NTA)-modified AuNPs (21.3 nm in core diameter), leading to the self-assembly of AuNPs and consequently changes in color of the AuNP solution. In contrast, unphosphorylated peptides and His6-deficient phosphopeptides did not change the color of the AuNP solution. As a result, protein phosphatase 1 (PP1) activity and its inhibition were easily quantified with high sensitivity by determining the extinction ratio (E520/E700) of colloidal AuNPs. Most importantly, this method was capable of detecting protein phosphatase 2A (PP2A) activity in immunoprecipitated plant extracts. Because PPs play pivotal roles in mediating diverse signal transduction pathways as primary effectors of protein dephosphorylation, we anticipate that our method will be applied as a rapid format method to analyze the activities of various PPs and their inhibition.

Comparative Study of Hand-Sutured versus Circular Stapled Anastomosis for Gastrojejunostomy in Laparoscopy Assisted Distal Gastrectomy

PubMed Central

Seo, Su Hyun; Kim, Min Chan; Choi, Hong Jo; Jung, Ghap Joong

2012-01-01

Purpose Mechanical stapler is regarded as a good alternative to the hand sewing technique, when used in gastric reconstruction. The circular stapling method has been widely applied to gastrectomy (open orlaparoscopic), for gastric cancer. We illustrated and compared the hand-sutured method to the circular stapling method, for Billroth-II, in patients who underwent laparoscopy assisted distal gastrectomy for gastric cancer. Materials and Methods Between April 2009 and May 2011, 60 patients who underwent laparoscopy assisted distal gastrectomy, with Billroth-II, were enrolled. Hand-sutured Billroth-II was performed in 40 patients (manual group) and circular stapler Billroth-II was performed in 20 patients (stapler group). Clinicopathological features and post-operative outcomes were evaluated and compared between the two groups. Results Nosignificant differences were observed in clinicopathologic parameters and post-operative outcomes, except in the operation times. Operation times and anastomosis times were significantly shorter in the stapler group (P=0.004 and P<0.001). Conclusions Compared to the hand-sutured method, the circular stapling method can be applied safely and more efficiently, when performing Billroth-II anastomosis, after laparoscopy assisted distal gastrectomy in patients with gastric cancer. PMID:22792525

Towards a selective adsorbent for arsenate and selenite in the presence of phosphate: Assessment of adsorption efficiency, mechanism, and binary separation factors of the chitosan-copper complex.

PubMed

Yamani, Jamila S; Lounsbury, Amanda W; Zimmerman, Julie B

2016-01-01

The potential for a chitosan-copper polymer complex to select for the target contaminants in the presence of their respective competitive ions was evaluated by synthesizing chitosan-copper beads (CCB) for the treatment of (arsenate:phosphate), (selenite:phosphate), and (selenate:sulfate). Based on work by Rhazi et al., copper (II) binds to the amine moiety on the chitosan backbone as a monodentate complex (Type I) and as a bidentate complex crosslinking two polymer chains (Type II), depending on pH and copper loading. In general, the Type I complex exists alone; however, beyond threshold conditions of pH 5.5 during synthesis and a copper loading of 0.25 mol Cu(II)/mol chitosan monomer, the Type I and Type II complexes coexist. Subsequent chelation of this chitosan-copper ligand to oxyanions results in enhanced and selective adsorption of the target contaminants in complex matrices with high background ion concentrations. With differing affinities for arsenate, selenite, and phosphate, the Type I complex favors phosphate chelation while the Type II complex favors arsenate chelation due to electrostatic considerations and selenite chelation due to steric effects. No trend was exhibited for the selenate:sulfate system possibly due to the high Ksp of the corresponding copper salts. Binary separation factors, α12, were calculated for the arsenate-phosphate and selenite-phosphate systems, supporting the mechanistic hypothesis. While, further research is needed to develop a synthesis method for the independent formation of the Type II complexes to select for target contaminants in complex matrices, this work can provide initial steps in the development of a selective adsorbent. Copyright © 2015 Elsevier Ltd. All rights reserved.

Central IKKβ inhibition prevents air pollution mediated peripheral inflammation and exaggeration of type II diabetes.

PubMed

Liu, Cuiqing; Fonken, Laura K; Wang, Aixia; Maiseyeu, Andrei; Bai, Yuntao; Wang, Tse-Yao; Maurya, Santosh; Ko, Yi-An; Periasamy, Muthu; Dvonch, Timothy; Morishita, Masako; Brook, Robert D; Harkema, Jack; Ying, Zhekang; Mukherjee, Bhramar; Sun, Qinghua; Nelson, Randy J; Rajagopalan, Sanjay

2014-10-30

Prior experimental and epidemiologic data support a link between exposure to fine ambient particulate matter (<2.5 μm in aerodynamic diameter, PM2.5) and development of insulin resistance/Type II diabetes mellitus (Type II DM). We investigated the role of hypothalamic inflammation in PM2.5-mediated diabetes development. KKay mice, a genetically susceptible model of Type II DM, were assigned to either concentrated PM2.5 or filtered air (FA) for 4-8 weeks via a versatile aerosol concentrator and exposure system, or administered intra-cerebroventricular with either IKKβ inhibitor (IMD-0354) or TNFα antibody (infliximab) for 4-5 weeks simultaneously with PM2.5 exposure. Glucose tolerance, insulin sensitivity, oxygen consumption and heat production were evaluated. At euthanasia, blood, spleen, visceral adipose tissue and hypothalamus were collected to measure inflammatory cells using flow cytometry. Standard immunohistochemical methods and quantitative PCR were used to assess targets of interest. PM2.5 exposure led to hyperglycemia and insulin resistance, which was accompanied by increased hypothalamic IL-6, TNFα, and IKKβ mRNA expression and microglial/astrocyte reactivity. Targeting the NFκB pathway with intra-cerebroventricular administration of an IKKβ inhibitor [IMD-0354, n = 8 for each group)], but not TNFα blockade with infliximab [(n = 6 for each group], improved glucose tolerance, insulin sensitivity, rectified energy homeostasis (O2 consumption, CO2 production, respiratory exchange ratio and heat generation) and reduced peripheral inflammation in response to PM2.5. Central inhibition of IKKβ prevents PM2.5 mediated peripheral inflammation and exaggeration of type II diabetes. These results provide novel insights into how air pollution may mediate susceptibility to insulin resistance and Type II DM.

An experimental system for spectral line ratio measurements in the TJ-II stellarator.

PubMed

Zurro, B; Baciero, A; Fontdecaba, J M; Peláez, R; Jiménez-Rey, D

2008-10-01

The chord-integrated emissions of spectral lines have been monitored in the TJ-II stellarator by using a spectral system with time and space scanning capabilities and relative calibration over the entire UV-visible spectral range. This system has been used to study the line ratio of lines of different ionization stages of carbon (C(5+) 5290 A and C(4+) 2271 A) for plasma diagnostic purposes. The local emissivity of these ions has been reconstructed, for quasistationary profiles, by means of the inversion Fisher method described previously. The experimental line ratio is being empirically studied and in parallel a simple spectroscopic model has been developed to account for that ratio. We are investigating whether the role played by charge exchange processes with neutrals and the existence of non-Maxwellian electrons, intrinsic to Electron Cyclotron Resonance Heating (ECRH) heating, leave any distinguishable mark on this diagnostic method.

Palladium(ii)-catalyzed synthesis of dibenzothiophene derivatives via the cleavage of carbon–sulfur and carbon–hydrogen bonds† †Electronic supplementary information (ESI) available: Experimental procedures and characterization data for all new compounds. See DOI: 10.1039/c5sc04890g Click here for additional data file.

PubMed Central

Masuya, Yoshihiro; Baba, Katsuaki

2016-01-01

A new process has been developed for the palladium(ii)-catalyzed synthesis of dibenzothiophene derivatives via the cleavage of C–H and C–S bonds. In contrast to the existing methods for the synthesis of this scaffold by C–H functionalization, this new catalytic C–H/C–S coupling method does not require the presence of an external stoichiometric oxidant or reactive functionalities such as C–X or S–H, allowing its application to the synthesis of elaborate π-systems. Notably, the product-forming step of this reaction lies in an oxidative addition step rather than a reductive elimination step, making this reaction mechanistically uncommon. PMID:28660030

BOND: A quantum of solace for nebular abundance determinations

NASA Astrophysics Data System (ADS)

Vale Asari, N.; Stasińska, G.; Morisset, C.; Cid Fernandes, R.

2017-11-01

The abundances of chemical elements other than hydrogen and helium in a galaxy are the fossil record of its star formation history. Empirical relations such as mass-metallicity relation are thus seen as guides for studies on the history and chemical evolution of galaxies. Those relations usually rely on nebular metallicities measured with strong-line methods, which assume that H II regions are a one- (or at most two-) parameter family where the oxygen abundance is the driving quantity. Nature is however much more complex than that, and metallicities from strong lines may be strongly biased. We have developed the method BOND (Bayesian Oxygen and Nitrogen abundance Determinations) to simultaneously derive oxygen and nitrogen abundances in giant H II regions by comparing strong and semi-strong observed emission lines to a carefully-defined, finely-meshed grid of photoionization models. Our code and results are public and available at http://bond.ufsc.br.

Development and validation of a selective, sensitive and stability indicating UPLC-MS/MS method for rapid, simultaneous determination of six process related impurities in darunavir drug substance.

PubMed

A, Vijaya Bhaskar Reddy; Yusop, Zulkifli; Jaafar, Jafariah; Aris, Azmi B; Majid, Zaiton A; Umar, Khalid; Talib, Juhaizah

2016-09-05

In this study a sensitive and selective gradient reverse phase UPLC-MS/MS method was developed for the simultaneous determination of six process related impurities viz., Imp-I, Imp-II, Imp-III, Imp-IV, Imp-V and Imp-VI in darunavir. The chromatographic separation was performed on Acquity UPLC BEH C18 (50 mm×2.1mm, 1.7μm) column using gradient elution of acetonitrile-methanol (80:20, v/v) and 5.0mM ammonium acetate containing 0.01% formic acid at a flow rate of 0.4mL/min. Both negative and positive electrospray ionization (ESI) modes were operated simultaneously using multiple reaction monitoring (MRM) for the quantification of all six impurities in darunavir. The developed method was fully validated following ICH guidelines with respect to specificity, linearity, limit of detection (LOD), limit of quantification (LOQ), accuracy, precision, robustness and sample solution stability. The method was able to quantitate Imp-I, Imp-IV, Imp-V at 0.3ppm and Imp-II, Imp-III, and Imp-VI at 0.2ppm with respect to 5.0mg/mL of darunavir. The calibration curves showed good linearity over the concentration range of LOQ to 250% for all six impurities. The correlation coefficient obtained was >0.9989 in all the cases. The accuracy of the method lies between 89.90% and 104.60% for all six impurities. Finally, the method has been successfully applied for three formulation batches of darunavir to determine the above mentioned impurities, however no impurity was found beyond the LOQ. This method is a good quality control tool for the trace level quantification of six process related impurities in darunavir during its synthesis. Copyright © 2016 Elsevier B.V. All rights reserved.

Dental health of 6-year-old children in Alpes Maritimes, France.

PubMed

Joseph, C; Velley, A M; Pierre, A; Bourgeois, D; Muller-Bolla, M

2011-10-01

To describe the dental health status of 6-year-old children using the ICDAS-II advanced method and to evaluate the association between the known caries risk factors with the cavitated caries lesion (WHO basic method) or with both non-cavitated and cavitated caries lesion caries (ICDAS II). In this cross-sectional study, a questionnaire was used to evaluate oral health and dietary habits of children. A clinical examination and a Cario analysis test (Pierre Fabre Oral care) were performed. Logistic regression analyses were used to assess the association between caries and daily tooth-brushing, dietary habits, visible plaque and salivary factors. There were 341 children (52% female and 6.25+/-0.46 years of age) in this study. Using the ICDAS-II advanced method, 39% of the children were caries-free. This proportion was larger (67.2%) using the WHO method. In multivariate models, visible dental plaque and Streptococcus mutans count were associated with caries experience registered as ICDAS-II codes 1-6 or codes 3-6. The absence of daily tooth-brushing with fluoridated toothpaste was associated only with caries experience ICDAS-II codes 3-6. The use of WHO or ICDAS-II method changed the proportion of caries-free children but not the clinical caries risk factors associated with caries experience.

On the Distance Measurements toward Young Milky Way Objects. I. Study of IC 2944

NASA Astrophysics Data System (ADS)

Krełowski, J.; Strobel, A.; Godunova, V.; Bondar, A.

2017-12-01

We compare distances to a very young stellar aggregate, IC 2944, using three methods: direct parallaxes of Gaia, spectrophotometric parallax and our method based on intensities of interstellar CaII lines. The discrepancies between spectrophotometric distances and those, based on CaII K and H lines, were already reported. The interstellar CaII H and K lines allow one to determine both distances and radial velocities of the intervening clouds. Thus, these data allow us to check the aggregate membership. It is also possible to check the spectral classification of considered targets which is necessary for spectrophotometric parallaxes. Using three methods, we determined distances to IC 2944 stars. We demonstrate that CaII based distances agree very well with the kinematic ones but are generally much smaller than the spectrophotometric ones. We conclude that the majority of IC 2944 objects is obscured by clouds producing neutral ("gray") extinction which diminishes their brightness exactly like extended distances. This influences spectrophotometric parallaxes while those, based on the CaII lines, do not depend on extinction and this method seems to be the most reliable one inside the thin disk of our Galaxy. The Gaia trigonometric parallaxes lead to distances similar to those obtained using the CaII method if their errors are reasonably small.