SPH Simulation of Impact of a Surge on a Wall

NASA Astrophysics Data System (ADS)

Diwakar, Manoj Kumar; Mohapatra, Pranab Kumar; Tripathi, Shivam

2014-05-01

Structures located on the downstream of a dam are prone to impact of the surge due to dam break flow. Ramsden (1996) experimentally studied the run-up height on a vertical wall due to propagation of bore and surge on dry bed and measured their impact on the wall. Mohapatra et al. (2000) applied Navier Stokes equations to numerically study the impact of bore on vertical and inclined walls. They also obtained the evolution of surge on dry bed. In the present work, the impact of a surge wave due to dam break flow against the wall is modeled with a two-dimensional smoothed particle hydrodynamics (SPH) model. SPH is a mesh-free method that relies on the particle view of the field problem and approximates the continuity and momentum equations on a set of particles. The method solves the strong form of Navier-Stokes equations. The governing equations are solved numerically in the vertical plane. The propagation of the surge wave, its impact and the maximum run-up on the wall located at the boundary are analyzed. Surface profile, velocity field and pressure distributions are simulated. Non-dimensional run-up height obtained from the present numerical model is 0.86 and is in good agreement with the available experimental data of Ramsden (1996) which is in the range of 0.75-0.9. Also, the simulated profile of the surge tip was comparable to the empirical equations refereed in Ramsden (1996). The model is applied to the study the maximum force and the run-up height on inclined walls with different inclinations. The results indicate that the maximum force and the run-up height on the wall increase with the increment of wall inclination. Comparison of numerical results with analytical solutions derived from shallow water equations clearly shows the breakdown of shallow water assumption during the impact. In addition to these results, the numerical simulation yields the complete velocity and pressure ?elds which may be used to design structures located in the path of a dam-break wave. The study shows that the smoothed particle hydrodynamics can effectively simulate fluid flow dynamics. References: Mohapatra, P. K., Bhallamudi, S. M., and Eswaran, V. (2000). 'Numerical simulation of impact of bores against inclined walls.' J. Hydraulic. Engg., ASCE, 126(12), 942-945. Ramsden, J. D. (1996). 'Forces on a vertical wall due to long waves, bores, and dry-bed surges.' J. Waterway, Port, Coastal, and Ocean Engg., ASCE, 122(3), 134-141.

The Fogo's Collapse-triggered Megatsunami: Evidence-calibrated Numerical Simulations of Tsunamigenic Potential and Coastal Impact

NASA Astrophysics Data System (ADS)

Omira, Rachid; Ramalho, Ricardo S.; Quartau, Rui; Ramalho, Inês; Madeira, José; Baptista, Maria Ana

2017-04-01

Volcanic Ocean Islands are very prominent and dynamic features involving several constructive and destructive phases during their life-cycles. Large-scale gravitational flank collapses are one of the most destructive processes and can present a major source of hazard, since it has been shown that these events are capable of triggering megatsunamis with significant coastal impact. The Fogo volcanic island, Cape Verde, presents evidence for giant edifice mass-wasting, as attested by both onshore and offshore evidence. A recent study by Ramalho et al. (2015) revealed the presence of tsunamigenic deposits that attest the generation of a megatsunami with devastating impact on the nearby Santiago Island, following Fogo's catastrophic collapse. Evidence from northern Santiago implies local minimum run-ups of 270 m, providing a unique physical framework to test collapse-triggered tsunami numerical simulations. In this study, we investigate the tsunamigenic potential associated with Fogo's flank collapse, and its impact on the Islands of the Cape Verde archipelago using field evidence-calibrated numerical simulations. We first reconstruct the pre-event island morphology, and then employ a multilayer numerical model to simulate the flank failure flow towards and under the sea, the ensuing tsunami generation, propagation and coastal impact. We use a digital elevation model that considers the coastline configuration and the sea level at the time of the event. Preliminary numerical modeling results suggest that collapsed volumes of 90-150 km3, in one single event, generate numerical solutions that are compatible with field evidence. Our simulations suggest that Fogo's collapse triggered a megatsunami that reached the coast of Santiago in 8 min, and with wave heights in excess of 250 m. The tsunami waves propagated with lower amplitudes towards the Cape Verde Islands located northward of Fogo. This study will contribute to more realistically assess the scale of risks associated with these extremely rare but very high impact natural disasters. This work is supported by the EU project ASTARTE -Grant 603839, 7th FP (ENV.2013, 6.4-3), the EU project TSUMAPS-NEAM -Agreement Number: ECHO/SUB/2015/718568/PREV26, and the IF/01641/2015 MEGAWAVE - FCT project.

From military to civil loadings: Preliminary numerical-based thorax injury criteria investigations.

PubMed

Goumtcha, Aristide Awoukeng; Bodo, Michèle; Taddei, Lorenzo; Roth, Sébastien

2016-03-01

Effects of the impact of a mechanical structure on the human body are of great interest in the understanding of body trauma. Experimental tests have led to first conclusions about the dangerousness of an impact observing impact forces or displacement time history with PMHS (Post Mortem human Subjects). They have allowed providing interesting data for the development and the validation of numerical biomechanical models. These models, widely used in the framework of automotive crashworthiness, have led to the development of numerical-based injury criteria and tolerance thresholds. The aim of this process is to improve the safety of mechanical structures in interaction with the body. In a military context, investigations both at experimental and numerical level are less successfully completed. For both military and civil frameworks, the literature list a number of numerical analysis trying to propose injury mechanisms, and tolerance thresholds based on biofidelic Finite Element (FE) models of different part of the human body. However the link between both frameworks is not obvious, since lots of parameters are different: great mass impacts at relatively low velocity for civil impacts (falls, automotive crashworthiness) and low mass at very high velocity for military loadings (ballistic, blast). In this study, different accident cases were investigated, and replicated with a previously developed and validated FE model of the human thorax named Hermaphrodite Universal Biomechanical YX model (HUBYX model). These previous validations included replications of standard experimental tests often used to validate models in the context of automotive industry, experimental ballistic tests in high speed dynamic impact and also numerical replication of blast loading test ensuring its biofidelity. In order to extend the use of this model in other frameworks, some real-world accidents were reconstructed, and consequences of these loadings on the FE model were explored. These various numerical replications of accident coming from different contexts raise the question about the ability of a FE model to correctly predict several kinds of trauma, from blast or ballistic impacts to falls, sports or automotive ones in a context of numerical injury mechanisms and tolerance limits investigations. Copyright © 2015 John Wiley & Sons, Ltd.

Evaluation of possible head injuries ensuing a cricket ball impact.

PubMed

Mohotti, Damith; Fernando, P L N; Zaghloul, Amir

2018-05-01

The aim of this research is to study the behaviour of a human head during the event of an impact of a cricket ball. While many recent incidents were reported in relation to head injuries caused by the impact of cricket balls, there is no clear information available in the published literature about the possible threat levels and the protection level of the current protective equipment. This research investigates the effects of an impact of a cricket ball on a human head and the level of protection offered by the existing standard cricket helmet. An experimental program was carried out to measure the localised pressure caused by the impact of standard cricket balls. The balls were directed at a speed of 110 km/h on a 3D printed head model, with and without a standard cricket helmet. Numerical simulations were carried out using advanced finite element package LS-DYNA to validate the experimental results. The experimental and numerical results showed approximately a 60% reduction in the pressure on the head model when the helmet was used. Both frontal and side impact resulted in head acceleration values in the range of 225-250 g at a ball speed of 110 km/h. There was a 36% reduction observed in the peak acceleration of the brain when wearing a helmet. Furthermore, numerical simulations showed a 67% reduction in the force on the skull and a 95% reduction in the skull internal energy when introducing the helmet. (1) Upon impact, high localised pressure could cause concussion for a player without helmet. (2) When a helmet was used, the acceleration of the brain observed in the numerical results was at non-critical levels according to existing standards. (3) A significant increase in the threat levels was observed for a player without helmet, based on force, pressure, acceleration and energy criteria, which resulted in recommending the compulsory use of the cricket helmet. (4) Numerical results showed a good correlation with experimental results and hence, the numerical technique used in this study can be recommended for future applications. Copyright © 2018 Elsevier B.V. All rights reserved.

Numerical and experimental study of blowing jet on a high lift airfoil

NASA Astrophysics Data System (ADS)

Bobonea, A.; Pricop, M. V.

2013-10-01

Active manipulation of separated flows over airfoils at moderate and high angles of attack in order to improve efficiency or performance has been the focus of a number of numerical and experimental investigations for many years. One of the main methods used in active flow control is the usage of blowing devices with constant and pulsed blowing. Through CFD simulation over a 2D high-lift airfoil, this study is trying to highlight the impact of pulsed blowing over its aerodynamic characteristics. The available wind tunnel data from INCAS low speed facility are also beneficial for the validation of the numerical analysis. This study intends to analyze the impact of the blowing jet velocity and slot geometry on the efficiency of an active flow control.

The Impacts of Numerical Schemes on Asymmetric Hurricane Intensification

NASA Astrophysics Data System (ADS)

Guimond, S.; Reisner, J. M.; Marras, S.; Giraldo, F.

2015-12-01

The fundamental pathways for tropical cyclone (TC) intensification are explored by considering axisymmetric and asymmetric impulsive thermal perturbations to balanced, TC-like vortices using the dynamic cores of three different numerical models. Attempts at reproducing the results of previous work, which used the community atmospheric model WRF (Nolan and Grasso 2003; NG03), revealed a discrepancy with the impacts of purely asymmetric thermal forcing. The current study finds that thermal asymmetries can have an important, largely positive role on the vortex intensification whereas NG03 and other studies find that asymmetric impacts are negligible. Analysis of the spectral energetics of each numerical model indicates that the vortex response to asymmetric thermal perturbations is significantly damped in WRF relative to the other numerical models. Spectral kinetic energy budgets show that this anomalous damping is due to the increased removal of kinetic energy from the convergence of the vertical pressure flux, which is related to the flux of inertia-gravity wave energy. The increased kinetic energy in the other two models is shown to originate around the scales of the heating and propagate upscale with time. For very large thermal amplitudes (~ 50 K and above), the anomalous removal of kinetic energy due to inertia-gravity wave activity is much smaller resulting in little differences between models. The results of this paper indicate that the numerical treatment of small-scale processes that project strongly onto inertia-gravity wave energy are responsible for these differences, with potentially important impacts for the understanding and prediction of TC intensification.

Application of Compressible Volume of Fluid Model in Simulating the Impact and Solidification of Hollow Spherical ZrO2 Droplet on a Surface

NASA Astrophysics Data System (ADS)

Safaei, Hadi; Emami, Mohsen Davazdah; Jazi, Hamidreza Salimi; Mostaghimi, Javad

2017-12-01

Applications of hollow spherical particles in thermal spraying process have been developed in recent years, accompanied by attempts in the form of experimental and numerical studies to better understand the process of impact of a hollow droplet on a surface. During such process, volume and density of the trapped gas inside droplet change. The numerical models should be able to simulate such changes and their consequent effects. The aim of this study is to numerically simulate the impact of a hollow ZrO2 droplet on a flat surface using the volume of fluid technique for compressible flows. An open-source, finite-volume-based CFD code was used to perform the simulations, where appropriate subprograms were added to handle the studied cases. Simulation results were compared with the available experimental data. Results showed that at high impact velocities ( U 0 > 100 m/s), the compression of trapped gas inside droplet played a significant role in the impact dynamics. In such velocities, the droplet splashed explosively. Compressibility effects result in a more porous splat, compared to the corresponding incompressible model. Moreover, the compressible model predicted a higher spread factor than the incompressible model, due to planetary structure of the splat.

a Study on Impact Analysis of Side Kick in Taekwondo

NASA Astrophysics Data System (ADS)

Lee, Jung-Hyun; Lee, Young-Shin; Han, Kyu-Hyun

Taekwondo is a martial art form and sport that uses the hands and feet for attack and defense. Taekwondo basic motion is composed of the breaking, competition and poomsea motions. The side kick is one of the most important breaking motions. The side kick with the front foot can be made in two steps. In the first step, the front foot is extended forward from the back stance free-fighting position. For the second step, the rear foot is followed simultaneously. Then, the side kick is executed while the entire body weight rests on the rear foot. In this paper, the impact analysis on a human model for kicking posture was carried out. The ADAMS/LifeMOD used numerical modeling and simulation for the side kick. The numerical human models for assailant and opponent in competition motion were developed. The maximum impact force on the human body was obtained by experiment and was applied to impact simulation. As a result, the impact displacement and velocity of the numerical human model were investigated.

Numerical and Experimental Studies on Impact Loaded Concrete Structures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saarenheimo, Arja; Hakola, Ilkka; Karna, Tuomo

2006-07-01

An experimental set-up has been constructed for medium scale impact tests. The main objective of this effort is to provide data for the calibration and verification of numerical models of a loading scenario where an aircraft impacts against a nuclear power plant. One goal is to develop and take in use numerical methods for predicting response of reinforced concrete structures to impacts of deformable projectiles that may contain combustible liquid ('fuel'). Loading, structural behaviour, like collapsing mechanism and the damage grade, will be predicted by simple analytical methods and using non-linear FE-method. In the so-called Riera method the behavior ofmore » the missile material is assumed to be rigid plastic or rigid visco-plastic. Using elastic plastic and elastic visco-plastic material models calculations are carried out by ABAQUS/Explicit finite element code, assuming axisymmetric deformation mode for the missile. With both methods, typically, the impact force time history, the velocity of the missile rear end and the missile shortening during the impact were recorded for comparisons. (authors)« less

Numerical simulations of tropical cyclones with assimilation of satellite, radar and in-situ observations: lessons learned from recent field programs and real-time experimental forecasts

NASA Astrophysics Data System (ADS)

Pu, Z.; Zhang, L.

2010-12-01

The impact of data assimilation on the predictability of tropical cyclones is examined with the cases from recent field programs and real-time hurricane forecast experiments. Mesoscale numerical simulations are performed to simulate major typhoons during the T-PARC/TCS08 field campaign with the assimilation of satellite, radar and in-situ observations. Results confirmed that data assimilation has indeed resulted in improved numerical simulations of tropical cyclones. However, positive impacts from the satellite and radar data are strongly depend on the quality of these data. Specifically, it is found that the overall impacts of assimilating AIRS retrieved atmospheric temperature and moisture profiles on numerical simulations of tropical cyclones are very sensitive to the bias corrections of the data.For instance, the dry biases of moisture profiles can cause the decay of tropical cyclones in the numerical simulations.In addition, the quality of airborne Doppler radar data has strong influence on numerical simulations of tropical cyclones in terms of their track, intensity and precipitation structures. Outcomes from assimilating radar data with various quality thresholds suggest that a trade-off between the quality and area coverage of the radar data is necessary in the practice. Some of those experiences obtained from the field case studies are applied to the near-real time experimental hurricane forecasts during the 2010 hurricane season. Results and issues raised from the case studies and real-time experiments will be discussed.

Utilization of satellite data and regional scale numerical models in short range weather forecasting

NASA Technical Reports Server (NTRS)

Kreitzberg, C. W.

1985-01-01

Overwhelming evidence was developed in a number of studies of satellite data impact on numerical weather prediction that it is unrealistic to expect satellite temperature soundings to improve detailed regional numerical weather prediction. It is likely that satellite data over the United States would substantially impact mesoscale dynamical predictions if the effort were made to develop a composite moisture analysis system. The horizontal variability of moisture, most clearly depicited in images from satellite water vapor channels, would not be determined from conventional rawinsondes even if that network were increased by a doubling of both the number of sites and the time frequency.

Numerical simulation of several impact attenuator design for a formula student car

NASA Astrophysics Data System (ADS)

Sinaga, Farlian Rizky; Ubaidillah, Kurniawan, Krishna Eka; Fadhil, Muhamad Ivan; Cahyono, Sukmaji Indro; Idris, Muhamad Hafiz

2018-02-01

In the Formula Society of Automotive Engineer (SAE), safety is a vigorous factor. One of the safety components in the Formula SAE car is the impact attenuator. The purpose of this study is to get the impact attenuator design with the best ability to absorb kinetic energy from several existing designs, through numerical approaches, for estimating conditions against dynamic impacts. Material of impact attenuator use combination of aluminum and Zirconium G350. The simulation was caried out by crashing the impact with the rigid wall, to find the deformation that occurs and the energies are absorbed. The impact attenuator design to be simulated should be optimized to meet some parameters in the SAE Formula. The result of impact attenuator simulation should be able to absorb energy of 7350 joules at move 7 m/s and deformation at bulkhead less than 25.4 mm.

Impacts of Noise Barriers on Near-Road Air Quality

EPA Science Inventory

Numerous health studies show an increase in adverse health effects for populations near large roadways. A study was designed to assess traffic emission impacts on air quality near a heavily traveled highway. The portion of highway studied included a section of open field and a se...

A numerical calculation method of environmental impacts for the deep sea mining industry - a review.

PubMed

Ma, Wenbin; van Rhee, Cees; Schott, Dingena

2018-03-01

Since the gradual decrease of mineral resources on-land, deep sea mining (DSM) is becoming an urgent and important emerging activity in the world. However, until now there has been no commercial scale DSM project in progress. Together with the reasons of technological feasibility and economic profitability, the environmental impact is one of the major parameters hindering its industrialization. Most of the DSM environmental impact research focuses on only one particular aspect ignoring that all the DSM environmental impacts are related to each other. The objective of this work is to propose a framework for the numerical calculation methods of the integrated DSM environmental impacts through a literature review. This paper covers three parts: (i) definition and importance description of different DSM environmental impacts; (ii) description of the existing numerical calculation methods for different environmental impacts; (iii) selection of a numerical calculation method based on the selected criteria. The research conducted in this paper provides a clear numerical calculation framework for DSM environmental impact and could be helpful to speed up the industrialization process of the DSM industry.

Dust Ejection Induced by Small Meteoroids Impacting Martian Surface

NASA Technical Reports Server (NTRS)

Shuvalov, Valery

2001-01-01

The objective of this study is numerical modeling of meteoroid impact on the martian surface and determination of the resulting dust cloud parameters. Additional information is contained in the original extended abstract.

Mechanical impact of dynamic phenomena in Francis turbines at off design conditions

NASA Astrophysics Data System (ADS)

Duparchy, F.; Brammer, J.; Thibaud, M.; Favrel, A.; Lowys, P. Y.; Avellan, F.

2017-04-01

At partial load and overload conditions, Francis turbines are subjected to hydraulic instabilities that can potentially result in high dynamic solicitations of the turbine components and significantly reduce their lifetime. This study presents both experimental data and numerical simulations that were used as complementary approaches to study these dynamic solicitations. Measurements performed on a reduced scale physical model, including a special runner instrumented with on-board strain gauges and pressure sensors, were used to investigate the dynamic phenomena experienced by the runner. They were also taken as reference to validate the numerical simulation results. After validation, advantage was taken from the numerical simulations to highlight the mechanical response of the structure to the unsteady hydraulic phenomena, as well as their impact on the fatigue damage of the runner.

A Systematic Review of the Research on Vocabulary Instruction That Impacts Text Comprehension

ERIC Educational Resources Information Center

Wright, Tanya S.; Cervetti, Gina N.

2017-01-01

Although numerous studies have identified a correlational relationship between vocabulary and comprehension, we know less about vocabulary interventions that impact reading comprehension. Therefore, this study is a systematic review of vocabulary interventions with comprehension outcomes. Analyses of 36 studies that met criteria are organized…

Equations to assess the impact resistance of fiber composites

NASA Technical Reports Server (NTRS)

Chamis, C. C.; Hanson, M. P.; Serafini, T. T.

1972-01-01

Numerical analysis of impact resistance of composite materials containing fibers is discussed. Mathematical model of longitudinal impact resistance is presented. Potential impact resistance of various fiber composites as obtained by numerical analysis is presented as plotted curve.

Evaluation of electrical power alternatives for the Pacific Northwest

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This study evaluates the concept of implementation of large-scale energy conservation to reduce end-use demand for electrical energy as an alternative to the need for continued construction of new power plants to meet projected energy requirements for the Pacific Northwest. In particular, the numerical accuracy, economic feasibility, and institutional impact of a conservation-oriented scenario developed by the Natural Resources Defense Council, Inc., is assessed, relative to the energy forecast prepared by the Pacific Northwest Utilities Conference Commission. The results of this study are presented in four detailed sections following an introductory and summary section: Reconstruction and Numerical Evaluation of Alternativemore » Scenario; Economic Analysis; Institutional Impact; and Impact of New National Energy Policy.« less

High velocity impact on composite link of aircraft wing flap mechanism

NASA Astrophysics Data System (ADS)

Heimbs, Sebastian; Lang, Holger; Havar, Tamas

2012-12-01

This paper describes the numerical investigation of the mechanical behaviour of a structural component of an aircraft wing flap support impacted by a wheel rim fragment. The support link made of composite materials was modelled in the commercial finite element code Abaqus/Explicit, incorporating intralaminar and interlaminar failure modes by adequate material models and cohesive interfaces. Validation studies were performed step by step using quasi-static tensile test data and low velocity impact test data. Finally, high velocity impact simulations with a metallic rim fragment were performed for several load cases involving different impact angles, impactor rotation and pre-stress. The numerical rim release analysis turned out to be an efficient approach in the development process of such composite structures and for the identification of structural damage and worst case impact loading scenarios.

A Numerical/Experimental Study on the Impact and CAI Behaviour of Glass Reinforced Compsite Plates

NASA Astrophysics Data System (ADS)

Perillo, Giovanni; Jørgensen, Jens K.; Cristiano, Roberta; Riccio, Aniello

2018-04-01

This paper focuses on the development of an advance numerical model specifically for simulating low velocity impact events and related stiffness reduction on composite structures. The model is suitable for low cost thick composite structures like wind turbine blade and maritime vessels. The model consist of a combination of inter and intra laminar models. The intra-laminar model present a combination of Puck and Hashin failure theories for the evaluation of the fibre and matrix failure. The inter-laminar damage is instead simulated by Cohesive Zone Method based on energy approach. Basic material properties, easily measurable according to standardized tests, are required. The model has been used to simulate impact and compression after impact tests. Experimental tests have been carried out on thick E-Glass/Epoxy composite commonly used in the wind turbine industry. The clustering effect as well as the consequence of the impact energy have been experimentally tested. The accuracy of numerical model has been verified against experimental data showing a very good accuracy of the model.

Numerical simulation study on thermal response of PBX 9501 to low velocity impact

NASA Astrophysics Data System (ADS)

Lou, Jianfeng; Zhou, Tingting; Zhang, Yangeng; Zhang, Xiaoli

2017-01-01

Impact sensitivity of solid high explosives, an important index in evaluating the safety and performance of explosives, is an important concern in handling, storage, and shipping procedures. It is a great threat for either bare dynamite or shell charge when subjected to low velocity impact involved in traffic accidents or charge piece drops. The Steven test is an effective tool to study the relative sensitivity of various explosives. In this paper, we built the numerical simulation method involving mechanical, thermo and chemical properties of Steven test based on the thermo-mechanical coupled material model. In the model, the stress-strain relationship is described by dynamic plasticity model, the thermal effect of the explosive induced by impact is depicted by isotropic thermal material model, the chemical reaction of explosives is described by Arrhenius reaction rate law, and the effects of heating and melting on mechanical properties and thermal properties of materials are also taken into account. Specific to the standard Steven test, the thermal and mechanical response rules of PBX 9501 at various impact velocities were numerically analyzed, and the threshold velocity of explosive initiation was obtained, which is in good agreement with experimental results. In addition, the effect of confine condition of test device to the threshold velocity was explored.

The stability of freak waves with regard to external impact and perturbation of initial data

NASA Astrophysics Data System (ADS)

Smirnova, Anna; Shamin, Roman

2014-05-01

We investigate solutions of the equations, describing freak waves, in perspective of stability with regard to external impact and perturbation of initial data. The modeling of freak waves is based on numerical solution of equations describing a non-stationary potential flow of the ideal fluid with a free surface. We consider the two-dimensional infinitely deep flow. For waves modeling we use the equations in conformal variables. The variant of these equations is offered in [1]. Mathematical correctness of these equations was discussed in [2]. These works establish the uniqueness of solutions, offer the effective numerical solution calculation methods, prove the numerical convergence of these methods. The important aspect of numerical modeling of freak waves is the stability of solutions, describing these waves. In this work we study the questions of stability with regards to external impact and perturbation of initial data. We showed the stability of freak waves numerical model, corresponding to the external impact. We performed series of computational experiments with various freak wave initial data and random external impact. This impact means the power density on free surface. In each experiment examine two waves: the wave that was formed by external impact and without one. In all the experiments we see the stability of equation`s solutions. The random external impact practically does not change the time of freak wave formation and its form. Later our work progresses to the investigation of solution's stability under perturbations of initial data. We take the initial data that provide a freak wave and get the numerical solution. In common we take the numerical solution of equation with perturbation of initial data. The computing experiments showed that the freak waves equations solutions are stable under perturbations of initial data.So we can make a conclusion that freak waves are stable relatively external perturbation and perturbation of initial data both. 1. Zakharov V.E., Dyachenko A.I., Vasilyev O.A. New method for numerical simulation of a nonstationary potential flow of incompressible fluid with a free surface// Eur. J.~Mech. B Fluids. 2002. V. 21. P. 283-291. 2. R.V. Shamin. Dynamics of an Ideal Liquid with a Free Surface in Conformal Variables // Journal of Mathematical Sciences, Vol. 160, No. 5, 2009. P. 537-678. 3. R.V. Shamin, V.E. Zakharov, A.I. Dyachenko. How probability for freak wave formation can be found // THE EUROPEAN PHYSICAL JOURNAL - SPECIAL TOPICS Volume 185, Number 1, 113-124, DOI: 10.1140/epjst/e2010-01242-y

Effect of the pool depth on drop impact splashing

NASA Astrophysics Data System (ADS)

Chizari, Hossain; Thoraval, Marie-Jean

2017-11-01

We investigate the effect of the pool depth on the splashing dynamics of drop impact. The splashing of a single drop impacting into a deep pool or on wet surface has been investigated for many years both numerically and experimentally. However, recent results have demonstrated the importance of the vorticity produced during the impact on the splashing behavior. More specifically, the shedding of a vortex ring inside the liquid during the impact can separate the splash jet into several parts. The shedding of the vorticity can be influenced by the proximity of the bottom of the pool, if the pool depth is small enough. We study here how the pool depth can affect the vorticity shedding and the resulting splashing jets. We perform axisymmetric numerical simulations of the impacts with the open sources codes Gerris and Basilisk, and systematically vary the impact conditions, focusing on the effect of pool depth in the splashing regimes.

Impact erosion model for gravity-dominated planetesimals

NASA Astrophysics Data System (ADS)

Genda, Hidenori; Fujita, Tomoaki; Kobayashi, Hiroshi; Tanaka, Hidekazu; Suetsugu, Ryo; Abe, Yutaka

2017-09-01

Disruptive collisions have been regarded as an important process for planet formation, while non-disruptive, small-scale collisions (hereafter called erosive collisions) have been underestimated or neglected by many studies. However, recent studies have suggested that erosive collisions are also important to the growth of planets, because they are much more frequent than disruptive collisions. Although the thresholds of the specific impact energy for disruptive collisions (QRD*) have been investigated well, there is no reliable model for erosive collisions. In this study, we systematically carried out impact simulations of gravity-dominated planetesimals for a wide range of specific impact energy (QR) from disruptive collisions (QR ∼ QRD*) to erosive ones (QR << QRD*) using the smoothed particle hydrodynamics method. We found that the ejected mass normalized by the total mass (Mej/Mtot) depends on the numerical resolution, the target radius (Rtar) and the impact velocity (vimp), as well as on QR, but that it can be nicely scaled by QRD* for the parameter ranges investigated (Rtar = 30-300 km, vimp = 2-5 km/s). This means that Mej/Mtot depends only on QR/QRD* in these parameter ranges. We confirmed that the collision outcomes for much less erosive collisions (QR < 0.01 QRD*) converge to the results of an impact onto a planar target for various impact angles (θ) and that Mej/Mtot ∝ QR/QRD* holds. For disruptive collisions (QR ∼ QRD*), the curvature of the target has a significant effect on Mej/Mtot. We also examined the angle-averaged value of Mej/Mtot and found that the numerically obtained relation between angle-averaged Mej/Mtot and QR/QRD* is very similar to the cases for θ = 45° impacts. We proposed a new erosion model based on our numerical simulations for future research on planet formation with collisional erosion.

Evaluation of binder aging and its influence in aging of hot mix asphalt concrete : literature review and experimental design.

DOT National Transportation Integrated Search

2009-02-01

Binder oxidation in pavements and its impact on pavement performance has been addressed by : numerous laboratory studies of binder oxidation chemistry, reaction kinetics, and hardening and its impact on : mixture fatigue. Studies also have included s...

On the influence of dynamic stress variations on strain accumulation in fault zones

NASA Astrophysics Data System (ADS)

Grigoriev, A. S.; Shilko, E. V.; Astafurov, S. V.; Dimaki, A. V.; Vysotsky, E. M.; Psakhie, S. G.

2015-10-01

In this paper, a numerical study of the influence of the stress state of interface of the block medium structural elements on the deformation response of interface to the dynamic impacts. It is shown that the basic characteristics of the stress state determining the deformation response of the interface are the values of shear stress and mean stress. It is found that the dependence of the irreversible displacement at the interface zone initiated by dynamic impact on the reduced shear stress is described by the logistic function. Herewith, the influence of the mean stress and dynamic impact energy on the value of displacement initiated by dynamic impact can be taken into account by dependence of the logistic function numerator on these parameters.

Numerical Modelling of Rayleigh Wave Propagation in Course of Rapid Impulse Compaction

NASA Astrophysics Data System (ADS)

Herbut, Aneta; Rybak, Jarosław

2017-10-01

As the soil improvement technologies are the area of a rapid development, they require designing and implementing novel methods of control and calibration in order to ensure the safety of geotechnical works. At Wroclaw University of Science and Technology (Poland), these new methods are continually developed with the aim to provide the appropriate tools for the preliminary design of work process, as well as for the further ongoing on-site control of geotechnical works (steel sheet piling, pile driving or soil improvement technologies). The studies include preliminary numerical simulations and field tests concerning measurements and continuous histogram recording of shocks and vibrations and its ground-born dynamic impact on engineering structures. The impact of vibrations on reinforced concrete and masonry structures in the close proximity of the construction site may be destroying in both architectural and structural meaning. Those limits are juxtaposed in codes of practice, but always need an individual judgment. The results and observations make it possible to delineate specific modifications to the parameters of technology applied (e.g. hammer drop height). On the basis of numerous case studies of practical applications, already summarized and published, we were able to formulate the guidelines for work on the aforementioned sites. This work presents specific aspects of the active design (calibration of building site numerical model) by means of technology calibration, using the investigation of the impact of vibrations that occur during the Impulse Compaction on adjacent structures. A case study entails the impact of construction works on Rayleigh wave propagation in the zone of 100 m (radius) around the Compactor.

Study on the influence of ground and satellite observations on the numerical air-quality for PM10 over Romanian territory

NASA Astrophysics Data System (ADS)

Dumitrache, Rodica Claudia; Iriza, Amalia; Maco, Bogdan Alexandru; Barbu, Cosmin Danut; Hirtl, Marcus; Mantovani, Simone; Nicola, Oana; Irimescu, Anisoara; Craciunescu, Vasile; Ristea, Alina; Diamandi, Andrei

2016-10-01

The numerical forecast of particulate matter concentrations in general, and PM10 in particular is a theme of high socio-economic relevance. The aim of this study was to investigate the impact of ground and satellite data assimilation of PM10 observations into the Weather Research and Forecasting model coupled with Chemistry (WRF-CHEM) numerical air quality model for Romanian territory. This is the first initiative of the kind for this domain of interest. Assimilation of satellite information - e.g. AOT's in air quality models is of interest due to the vast spatial coverage of the observations. Support Vector Regression (SVR) techniques are used to estimate the PM content from heterogeneous data sources, including EO products (Aerosol Optical Thickness), ground measurements and numerical model data (temperature, humidity, wind, etc.). In this study we describe the modeling framework employed and present the evaluation of the impact from the data assimilation of PM10 observations on the forecast of the WRF-CHEM model. Integrations of the WRF-CHEM model in data assimilation enabled/disabled configurations allowed the evaluation of satellite and ground data assimilation impact on the PM10 forecast performance for the Romanian territory. The model integration and evaluation were performed for two months, one in winter conditions (January 2013) and one in summer conditions (June 2013).

Experimental and numerical study of water-filled vessel impacted by flat projectiles

NASA Astrophysics Data System (ADS)

Zhang, Wei; Ren, Peng; Huang, Wei; Gao, Yu Bo

2014-05-01

To understand the failure modes and impact resistance of double-layer plates separated by water, a flat-nosed projectile was accelerated by a two-stage light gas gun against a water-filled vessel which was placed in an air-filled tank. Targets consisted of a tank made of two flat 5A06 aluminum alloy plates held by a high strength steel frame. The penetration process was recorded by a digital high-speed camera. The same projectile-target system was also used to fire the targets placed directly in air for comparison. Parallel numerical tests were also carried out. The result indicated that experimental and numerical results were in good agreement. Numerical simulations were able to capture the main physical behavior. It was also found that the impact resistance of double layer plates separated by water was lager than that of the target plates in air. Tearing was the main failure models of the water-filled vessel targets which was different from that of the target plates in air where the shear plugging was in dominate.

Numerical simulating and experimental study on the woven carbon fiber-reinforced composite laminates under low-velocity impact

NASA Astrophysics Data System (ADS)

Liu, Hanyang; Tang, Zhanwen; Pan, Lingying; Zhao, Weidong; Sun, Baogang; Jiang, Wenge

2016-05-01

Impact damage has been identified as a critical form of the defects that constantly threatened the reliability of composite structures, such as those used in the aerospace structures and systems. Low energy impacts can introduce barely visible damage and cause the degradation of structural stiffness, furthermore, the flaws caused by low-velocity impact are so dangerous that they can give rise to the further extended delaminations. In order to improve the reliability and load carrying capacity of composite laminates under low-velocity impact, in this paper, the numerical simulatings and experimental studies on the woven fiber-reinforced composite laminates under low-velocity impact with impact energy 16.7J were discussed. The low velocity impact experiment was carried out through drop-weight system as the reason of inertia effect. A numerical progressive damage model was provided, in which the damages of fiber, matrix and interlamina were considered by VUMT subroutine in ABAQUS, to determine the damage modes. The Hashin failure criteria were improved to cover the failure modes of fiber failure in the directions of warp/weft and delaminations. The results of Finite Element Analysis (FEA) were compared with the experimental results of nondestructive examination including the results of ultrasonic C-scan, cross-section stereomicroscope and contact force - time history curves. It is found that the response of laminates under low-velocity impact could be divided into stages with different damage. Before the max-deformation of the laminates occurring, the matrix cracking, fiber breakage and delaminations were simulated during the impactor dropping. During the releasing and rebounding period, matrix cracking and delaminations areas kept increasing in the laminates because of the stress releasing of laminates. Finally, the simulating results showed the good agreements with the results of experiment.

Small Impacts on Mars: Atmospheric Effects

NASA Technical Reports Server (NTRS)

Greeley, Ronald; Nemtchinov, Ivan V.

2002-01-01

The objectives of this investigation were to study the interaction of the atmosphere with the surface of Mars through the impact of small objects that would generate dust and set the dust into motion in the atmosphere. The approach involved numerical simulations of impacts and experiments under controlled conditions. Attachment: Atmospheric disturbances and radiation impulses caused by large-meteoroid impact in the surface of Mars.

Potential impact of future climate change on sugarcane under dryland conditions in Mexico

USDA-ARS?s Scientific Manuscript database

Assessments of impacts of future climate change on widely grown sugarcane varieties can guide decision-making at various levels and help ensure the economic stability of numerous rural households. This study assessed the potential impact of future climatic change on CP 72-2086 the most widely grown...

Developmental Education's Impact on Students' Academic Self-Concept and Self-Efficacy

ERIC Educational Resources Information Center

Martin, Kimberly; Goldwasser, Molly; Harris, Eugenia

2017-01-01

Students who are enrolled in developmental courses often persist at lower rates than students who enter college prepared for college-level work. This phenomenon has been attributed to numerous potential factors, including the psychological impact of assignment to developmental courses. This study examines the impact of enrollment in multiple…

Hybrid High-Impact Pedagogies: Integrating Service-Learning with Three Other High-Impact Pedagogies

ERIC Educational Resources Information Center

Bringle, Robert G.

2017-01-01

This article proposes enhancing student learning through civic engagement by considering the advantages of integrating service-learning with study away, research, and internships and pre-professional courses into first-order, second-order, and third-order hybrid high-impact pedagogies. Service-learning contributes numerous attributes to the other…

Numerical investigations on pressurized AL-composite vessel response to hypervelocity impacts: Comparison between experimental works and a numerical code

NASA Astrophysics Data System (ADS)

Mespoulet, Jérôme; Plassard, Fabien; Hereil, Pierre-Louis

2015-09-01

Response of pressurized composite-Al vessels to hypervelocity impact of aluminum spheres have been numerically investigated to evaluate the influence of initial pressure on the vulnerability of these vessels. Investigated tanks are carbon-fiber overwrapped prestressed Al vessels. Explored internal air pressure ranges from 1 bar to 300 bar and impact velocity are around 4400 m/s. Data obtained from experiments (Xray radiographies, particle velocity measurement and post-mortem vessels) have been compared to numerical results given from LS-DYNA ALE-Lagrange-SPH full coupling models. Simulations exhibit an under estimation in term of debris cloud evolution and shock wave propagation in pressurized air but main modes of damage/rupture on the vessels given by simulations are coherent with post-mortem recovered vessels from experiments. First results of this numerical work are promising and further simulation investigations with additional experimental data will be done to increase the reliability of the simulation model. The final aim of this crossed work is to numerically explore a wide range of impact conditions (impact angle, projectile weight, impact velocity, initial pressure) that cannot be explore experimentally. Those whole results will define a rule of thumbs for the definition of a vulnerability analytical model for a given pressurized vessel.

Impacts of the horizontal and vertical grids on the numerical solutions of the dynamical equations - Part 1: Nonhydrostatic inertia-gravity modes

NASA Astrophysics Data System (ADS)

Konor, Celal S.; Randall, David A.

2018-05-01

We have used a normal-mode analysis to investigate the impacts of the horizontal and vertical discretizations on the numerical solutions of the nonhydrostatic anelastic inertia-gravity modes on a midlatitude f plane. The dispersion equations are derived from the linearized anelastic equations that are discretized on the Z, C, D, CD, (DC), A, E and B horizontal grids, and on the L and CP vertical grids. The effects of both horizontal grid spacing and vertical wavenumber are analyzed, and the role of nonhydrostatic effects is discussed. We also compare the results of the normal-mode analyses with numerical solutions obtained by running linearized numerical models based on the various horizontal grids. The sources and behaviors of the computational modes in the numerical simulations are also examined.Our normal-mode analyses with the Z, C, D, A, E and B grids generally confirm the conclusions of previous shallow-water studies for the cyclone-resolving scales (with low horizontal wavenumbers). We conclude that, aided by nonhydrostatic effects, the Z and C grids become overall more accurate for cloud-resolving resolutions (with high horizontal wavenumbers) than for the cyclone-resolving scales.A companion paper, Part 2, discusses the impacts of the discretization on the Rossby modes on a midlatitude β plane.

Be Cool with Academic Stress: The Association between Emotional States and Regulatory Strategies among Chinese Adolescents

ERIC Educational Resources Information Center

Sang, Biao; Pan, Tingting; Deng, Xinmei; Zhao, Xu

2018-01-01

Numerous studies have suggested that academic stress has negative impact on adolescents' psychological function, few of those studies, however, considered whether and how the impact of stress on adolescents' emotional states is moderated by corresponding regulation. This study aimed to examine the fluctuation of emotional states before and after…

The Juggling Act: A Phenomenological Study of Gifted and Talented Girls' Experiences with Facebook

ERIC Educational Resources Information Center

Price, Eunice; Wardman, Janna; Bruce, Toni; Millward, Pam

2016-01-01

Facebook is a frequently accessed social networking site with more than one billion active users worldwide. Although there are numerous studies on its impact on teenagers, none have investigated its impact on gifted and talented girls. This study's aim was to understand the social media experiences of talented female student leaders. A qualitative…

On the Impact of Collisions on Particle Dispersion in a Shear Layer

NASA Astrophysics Data System (ADS)

Soteriou, Marios; Mosley, John

1999-11-01

In this numerical study the impact of collisions on the evolution of a dispersed phase in a gaseous shear layer flow is investigated. The disperse phase consists of spherical particles which may experience two modes of collision: In the first, the collision has no effect on the particles themselves and is simply registered for accounting purposes. In the second, the particles coalesce upon impact into a larger spherical particle. The two phase mixture is assumed to be dilute and hence the impact of the disperse phase on the carrier phase is disabled. The unaveraged evolution of the carrier phase is simulated by using the Lagrangian Vortex Element Method while that of the dispersed phase by computing the trajectories of individual particles. Thus the numerical model is totally Lagrangian and grid-free. Numerical results indicate that collisions are maximized at intermediate Stokes numbers and that for a given volume fraction they increase as the particles get smaller. Coalescence of particles tends to reduce the overall number of collisions in the flow and alters their locus, shifting them predominately upstream. It also has a dramatic impact on dispersion increasing it substantially for the cases that experience even moderate number of collisions.

Numerical Analysis of Constrained Dynamical Systems, with Applications to Dynamic Contact of Solids, Nonlinear Elastodynamics and Fluid-Structure Interactions

DTIC Science & Technology

2000-12-01

Numerical Simulations ..... ................. .... 42 1.4.1. Impact of a rod on a rigid wall ..... ................. .... 42 1.4.2. Impact of two...dissipative properties of the proposed scheme . . . . 81 II.4. Representative Numerical Simulations ...... ................. ... 84 11.4.1. Forging of...Representative numerical simulations ...... ............. .. 123 111.3. Model Problem II: a Simplified Model of Thin Beams ... ......... ... 127 III

Exploring the Impact of Gambling Advertising: An Interview Study of Problem Gamblers

ERIC Educational Resources Information Center

Binde, Per

2009-01-01

This study qualitatively explored the impact of gambling advertising on problem gambling by interviewing twenty-five people with current or past gambling problems. Interviews were relatively long and involved the participants' viewing numerous examples of gambling advertising. A quarter of the participants reported that gambling advertising had no…

Meteoroid/space debris impacts on MSFC LDEF experiments

NASA Technical Reports Server (NTRS)

Finckenor, Miria

1992-01-01

The many meteoroid and space debris impacts found on A0171, A0034, S1005, and other MSFC experiments are considered. In addition to those impacts found by the meteoroid and debris studies, numerous impacts less than 0.5 mm were found and photographed. The flux and size distribution of impacts is presented as well as EDS analysis of impact residue. Emphasis is on morphology of impacts in the various materials, including graphite/epoxy composites, polymeric materials, optical coatings, thin films, and solar cells.

Numerical Acuity Enhancement in Kindergarten: How Much Does Material Presentation Form Mean?

ERIC Educational Resources Information Center

Mascia, Maria Lidia; Fastame, Maria Chiara; Agus, Mirian; Lucangeli, Daniela; Penna, Maria Pietronilla

2016-01-01

The current study aimed at exploring the impact of the modality in which numerical trainings proposed in kindergarten school. Participants were recruited from some Sardinian kindergarten schools and were then divided into three groups: a control group, which had to carry out the activities planned by the educational curriculum, and two…

Effects of Numeric Representation of Women on Interest in Engineering as a Career

ERIC Educational Resources Information Center

Creamer, Elizabeth G.

2012-01-01

Little is known about how the presence of women influences undergraduates' experiences in engineering. This paper presents results from a mixed methods, multivariate, and multi-institutional study to determine the impact of the numeric representation of women on the intent to be employed in engineering following graduation. Results from the…

Numerical Activities of Daily Living in Adults with Neurofibromatosis Type 1

ERIC Educational Resources Information Center

Burgio, F.; Benavides-Varela, S.; Arcara, G.; Trevisson, E.; Frizziero, D.; Clementi, M.; Semenza, C.

2017-01-01

Background: This study aimed to identify the mathematical domains affected in adults with neurofibromatosis 1 (NF1) and the impact of the numerical difficulties on the patients' activities of daily living. Methods: We assessed 28 adult patients with NF1 and 28 healthy control participants. All participants completed the standardised battery of…

Impact of Working Memory Training Targeting the Central Executive on Kindergarteners' Numerical Skills

ERIC Educational Resources Information Center

Honoré, Nastasya; Noël, Marie-Pascale

2017-01-01

Working memory capacities are associated with mathematical development. Many studies have tried to improve working memory abilities through training. Furthermore, the central executive has been shown to be the component of working memory, which is the most strongly related to numerical and arithmetical skills. Therefore, we developed a training…

Numerical Simulation of Oblique Impacts: Impact Melt and Transient Cavity Size

NASA Technical Reports Server (NTRS)

Artemieva, N. A.; Ivanov, B. A.

2001-01-01

We present 3D hydrocode numerical modeling for oblique impacts (i) to estimate the melt production and (ii) to trace the evolution of the transient cavity shape till the crater collapse. Additional information is contained in the original extended abstract.

Seismic wave propagation in granular media

NASA Astrophysics Data System (ADS)

Tancredi, Gonzalo; López, Francisco; Gallot, Thomas; Ginares, Alejandro; Ortega, Henry; Sanchís, Johnny; Agriela, Adrián; Weatherley, Dion

2016-10-01

Asteroids and small bodies of the Solar System are thought to be agglomerates of irregular boulders, therefore cataloged as granular media. It is a consensus that many asteroids might be considered as rubble or gravel piles.Impacts on their surface could produce seismic waves which propagate in the interior of these bodies, thus causing modifications in the internal distribution of rocks and ejections of particles and dust, resulting in a cometary-type comma.We present experimental and numerical results on the study of propagation of impact-induced seismic waves in granular media, with special focus on behavior changes by increasing compression.For the experiment, we use an acrylic box filled with granular materials such as sand, gravel and glass spheres. Pressure inside the box is controlled by a movable side wall and measured with sensors. Impacts are created on the upper face of the box through a hole, ranging from free-falling spheres to gunshots. We put high-speed cameras outside the box to record the impact as well as piezoelectic sensors and accelerometers placed at several depths in the granular material to detect the seismic wave.Numerical simulations are performed with ESyS-Particle, a software that implements the Discrete Element Method. The experimental setting is reproduced in the numerical simulations using both individual spherical particles and agglomerates of spherical particles shaped as irregular boulders, according to rock models obtained with a 3D scanner. The numerical experiments also reproduces the force loading on one of the wall to vary the pressure inside the box.We are interested in the velocity, attenuation and energy transmission of the waves. These quantities are measured in the experiments and in the simulations. We study the dependance of these three parameters with characteristics like: impact speed, properties of the target material and the pressure in the media.These results are relevant to understand the outcomes of impacts in rubble/gravel pile asteroids.

Testing and numerical modeling of hypervelocity impact damaged Space Station multilayer insulation

NASA Technical Reports Server (NTRS)

Rule, William K.

1992-01-01

Results are presented of experiments measuring the degradation of the insulating capabilities of the multilayer insulation (MLI) of the Space Station Freedom, when subjected to hypervelocity impact damage. A simple numerical model was developed for use in an engineering design environment for quick assessment of thermal effect of the impact. The model was validated using results from thermal vacuum tests on MLI with simulated damage. The numerical model results agreed with experimental data.

Analytical research on impacting load of aircraft crashing upon moveable concrete target

NASA Astrophysics Data System (ADS)

Zhu, Tong; Ou, Zhuocheng; Duan, Zhuoping; Huang, Fenglei

2018-03-01

The impact load of an aircraft impact upon moveable concrete target was analyzed in this paper by both theoretical and numerical methods. The aircraft was simplified as a one dimensional pole and stress-wave theory was used to deduce the new formula. Furthermore, aiming to compare with previous experimental data, a numerical calculation based on the new formula had been carried out which showed good agreement with the experimental data. The approach, a new formula with particular numerical method, can predict not only the impact load but also the deviation between moveable and static concrete target.

Constraining the thermal conditions of impact environments through integrated low-temperature thermochronometry and numerical modeling

NASA Astrophysics Data System (ADS)

Kelly, N. M.; Marchi, S.; Mojzsis, S. J.; Flowers, R. M.; Metcalf, J. R.; Bottke, W. F., Jr.

2017-12-01

Impacts have a significant physical and chemical influence on the surface conditions of a planet. The cratering record is used to understand a wide array of impact processes, such as the evolution of the impact flux through time. However, the relationship between impactor size and a resulting impact crater remains controversial (e.g., Bottke et al., 2016). Likewise, small variations in the impact velocity are known to significantly affect the thermal-mechanical disturbances in the aftermath of a collision. Development of more robust numerical models for impact cratering has implications for how we evaluate the disruptive capabilities of impact events, including the extent and duration of thermal anomalies, the volume of ejected material, and the resulting landscape of impacted environments. To address uncertainties in crater scaling relationships, we present an approach and methodology that integrates numerical modeling of the thermal evolution of terrestrial impact craters with low-temperature, (U-Th)/He thermochronometry. The approach uses time-temperature (t-T) paths of crust within an impact crater, generated from numerical simulations of an impact. These t-T paths are then used in forward models to predict the resetting behavior of (U-Th)/He ages in the mineral chronometers apatite and zircon. Differences between the predicted and measured (U-Th)/He ages from a modeled terrestrial impact crater can then be used to evaluate parameters in the original numerical simulations, and refine the crater scaling relationships. We expect our methodology to additionally inform our interpretation of impact products, such as lunar impact breccias and meteorites, providing robust constraints on their thermal histories. In addition, the method is ideal for sample return mission planning - robust "prediction" of ages we expect from a given impact environment enhances our ability to target sampling sites on the Moon, Mars or other solar system bodies where impacts have strongly shaped the surface. Bottke, W.F., Vokrouhlicky, D., Ghent, B., et al. (2016). 47th LPSC, Abstract #2036.

3D numerical simulations of oblique droplet impact onto a deep liquid pool

NASA Astrophysics Data System (ADS)

Gelderblom, Hanneke; Reijers, Sten A.; Gielen, Marise; Sleutel, Pascal; Lohse, Detlef; Xie, Zhihua; Pain, Christopher C.; Matar, Omar K.

2017-11-01

We study the fluid dynamics of three-dimensional oblique droplet impact, which results in phenomena that include splashing and cavity formation. An adaptive, unstructured mesh modelling framework is employed here, which can modify and adapt unstructured meshes to better represent the underlying physics of droplet dynamics, and reduce computational effort without sacrificing accuracy. The numerical framework consists of a mixed control-volume and finite-element formulation, a volume-of-fluid-type method for the interface-capturing based on a compressive control-volume advection method. The framework also features second-order finite-element methods, and a force-balanced algorithm for the surface tension implementation, minimising the spurious velocities often found in many simulations involving capillary-driven flows. The numerical results generated using this framework are compared with high-speed images of the interfacial shapes of the deformed droplet, and the cavity formed upon impact, yielding good agreement. EPSRC, UK, MEMPHIS program Grant (EP/K003976/1), RAEng Research Chair (OKM).

Meteoroid/space debris impacts on MSFC LDEF experiments

NASA Technical Reports Server (NTRS)

Finckenor, Miria

1991-01-01

The numerous meteoroid and space debris impacts found on AO171, AO034, S0069, and other MSFC experiments are examined. Besides those impacts found by the Meteoroid and Debris Special Investigative Group at KSC, numerous impacts of less than 0.5 mm were found and photographed. The flux and size distribution of impacts are presented as well as EDS analysis of impact residue. Emphasis is on morphology of impacts in the various materials, including graphite/epoxy composites, polymeric materials, optical coatings, thin films, and solar cells.

An approach to developing numeric water quality criteria for coastal waters using the SeaWiFS Satellite Data Record.

PubMed

Schaeffer, Blake A; Hagy, James D; Conmy, Robyn N; Lehrter, John C; Stumpf, Richard P

2012-01-17

Human activities on land increase nutrient loads to coastal waters, which can increase phytoplankton production and biomass and associated ecological impacts. Numeric nutrient water quality standards are needed to protect coastal waters from eutrophication impacts. The Environmental Protection Agency determined that numeric nutrient criteria were necessary to protect designated uses of Florida's waters. The objective of this study was to evaluate a reference condition approach for developing numeric water quality criteria for coastal waters, using data from Florida. Florida's coastal waters have not been monitored comprehensively via field sampling to support numeric criteria development. However, satellite remote sensing had the potential to provide adequate data. Spatial and temporal measures of SeaWiFS OC4 chlorophyll-a (Chl(RS)-a, mg m(-3)) were resolved across Florida's coastal waters between 1997 and 2010 and compared with in situ measurements. Statistical distributions of Chl(RS)-a were evaluated to determine a quantitative reference baseline. A binomial approach was implemented to consider how new data could be assessed against the criteria. The proposed satellite remote sensing approach to derive numeric criteria may be generally applicable to other coastal waters.

An Approach to Developing Numeric Water Quality Criteria for Coastal Waters Using the SeaWiFS Satellite Data Record

PubMed Central

2011-01-01

Human activities on land increase nutrient loads to coastal waters, which can increase phytoplankton production and biomass and associated ecological impacts. Numeric nutrient water quality standards are needed to protect coastal waters from eutrophication impacts. The Environmental Protection Agency determined that numeric nutrient criteria were necessary to protect designated uses of Florida’s waters. The objective of this study was to evaluate a reference condition approach for developing numeric water quality criteria for coastal waters, using data from Florida. Florida’s coastal waters have not been monitored comprehensively via field sampling to support numeric criteria development. However, satellite remote sensing had the potential to provide adequate data. Spatial and temporal measures of SeaWiFS OC4 chlorophyll-a (ChlRS-a, mg m–3) were resolved across Florida’s coastal waters between 1997 and 2010 and compared with in situ measurements. Statistical distributions of ChlRS-a were evaluated to determine a quantitative reference baseline. A binomial approach was implemented to consider how new data could be assessed against the criteria. The proposed satellite remote sensing approach to derive numeric criteria may be generally applicable to other coastal waters. PMID:22192062

Lyapunov spectrum of the separated flow around the NACA 0012 airfoil and its dependence on numerical discretization

NASA Astrophysics Data System (ADS)

Fernandez, P.; Wang, Q.

2017-12-01

We investigate the impact of numerical discretization on the Lyapunov spectrum of separated flow simulations. The two-dimensional chaotic flow around the NACA 0012 airfoil at a low Reynolds number and large angle of attack is considered to that end. Time, space and accuracy-order refinement studies are performed to examine each of these effects separately. Numerical results show that the time discretization has a small impact on the dynamics of the system, whereas the spatial discretization can dramatically change them. Also, the finite-time Lyapunov exponents associated to unstable modes are shown to be positively skewed, and quasi-homoclinic tangencies are observed in the attractor of the system. The implications of these results on flow physics and sensitivity analysis of chaotic flows are discussed.

Hybrid Particle-Element Simulation of Impact on Composite Orbital Debris Shields

NASA Technical Reports Server (NTRS)

Fahrenthold, Eric P.

2004-01-01

This report describes the development of new numerical methods and new constitutive models for the simulation of hypervelocity impact effects on spacecraft. The research has included parallel implementation of the numerical methods and material models developed under the project. Validation work has included both one dimensional simulations, for comparison with exact solutions, and three dimensional simulations of published hypervelocity impact experiments. The validated formulations have been applied to simulate impact effects in a velocity and kinetic energy regime outside the capabilities of current experimental methods. The research results presented here allow for the expanded use of numerical simulation, as a complement to experimental work, in future design of spacecraft for hypervelocity impact effects.

SPH calculations of Mars-scale collisions: The role of the equation of state, material rheologies, and numerical effects

NASA Astrophysics Data System (ADS)

Emsenhuber, Alexandre; Jutzi, Martin; Benz, Willy

2018-02-01

We model large-scale ( ≈ 2000 km) impacts on a Mars-like planet using a Smoothed Particle Hydrodynamics code. The effects of material strength and of using different Equations of State on the post-impact material and temperature distributions are investigated. The properties of the ejected material in terms of escaping and disc mass are analysed as well. We also study potential numerical effects in the context of density discontinuities and rigid body rotation. We find that in the large-scale collision regime considered here (with impact velocities of 4 km/s), the effect of material strength is substantial for the post-impact distribution of the temperature and the impactor material, while the influence of the Equation of State is more subtle and present only at very high temperatures.

Wave propagation in a plate after impact by a projectile

NASA Technical Reports Server (NTRS)

El-Raheb, M.; Wagner, P.

1987-01-01

The wave propagation in a circular plate after impact by a cylindrical projectile is studied. In the vicinity of impact, the pressure is computed numerically. An intense pressure pulse is generated that peaks 0.2 microns after impact, then drops sharply to a plateau. The response of the plate is determined adopting a modal solution of Mindlin's equations. Velocity and acceleration histories display both propagating and dispersive features.

Numerical study of the impact of a drop containing a bubble

NASA Astrophysics Data System (ADS)

Wei, Yu; Thoraval, Marie-Jean

2017-11-01

The impact of a drop has many applications from inkjet printing to the spreading of crops diseases. This fundamental phenomenon has therefore attracted a lot of interest from different fields. However, they have mostly focused on the simplest case of a drop containing a single fluid. In inkjet printing and in the deposition process of thermal barrier coatings, some bubbles can be present in the drop when it impacts on the solid surface. The presence of the bubble can produce some additional splashing, and affect the quality of the deposited material. Only a few studies have looked at this problem, and many questions still need to be investigated. Generally, there are three possibilities when a drop containing a bubble impacts onto a solid surface, namely the bubble stays in drop, the bubble bursts and a counter jet forms. We have performed axisymmetric numerical simulations with the open source code Gerris to study this vertical jet. We have systematically varied several parameters, including the impact velocity, the bubble size, the vertical position of the bubble, and the liquid properties. We were thus able to characterize under which condition the bubble leads to splashing and the velocity of the produced jet.

Fluid-structure interaction analysis of the drop impact test for helicopter fuel tank.

PubMed

Yang, Xianfeng; Zhang, Zhiqiang; Yang, Jialing; Sun, Yuxin

2016-01-01

The crashworthiness of helicopter fuel tank is vital to the survivability of the passengers and structures. In order to understand and improve the crashworthiness of the soft fuel tank of helicopter during the crash, this paper investigated the dynamic behavior of the nylon woven fabric composite fuel tank striking on the ground. A fluid-structure interaction finite element model of the fuel tank based on the arbitrary Lagrangian-Eulerian method was constructed to elucidate the dynamic failure behavior. The drop impact tests were conducted to validate the accuracy of the numerical simulation. Good agreement was achieved between the experimental and numerical results of the impact force with the ground. The influences of the impact velocity, the impact angle, the thickness of the fuel tank wall and the volume fraction of water on the dynamic responses of the dropped fuel tank were studied. The results indicated that the corner of the fuel tank is the most vulnerable location during the impact with ground.

Experimental Study and Numerical Modelling of Low Velocity Impact on Laminated Composite Reinforced with Thin Film Made of Carbon Nanotubes

NASA Astrophysics Data System (ADS)

El Moumen, A.; Tarfaoui, M.; Hassoon, O.; Lafdi, K.; Benyahia, H.; Nachtane, M.

2018-04-01

In this work, polymer laminated composites based on Epon 862 Epoxy resin, T300 6 k carbon fibers and carbon nanotubes (CNTs) were tested with the aim to elucidate the effect of CNTs on impact properties including impact force and capacity to absorb impact energy. The polymer matrix was reinforced by a random distribution of CNTs with fraction ranging from 0.5 to 4.wt%. Composite panels were manufactured by using the infusion process. Taylor impact test was used to obtain the impact response of specimens. Projectile manufactured from a high strength and hardened steel with a diameter of 20 mm and 1.5 kg of mass was launched by a compressed gas gun within the velocity of 3 m/s. Impact force histories and absorbed energy of specimens were recorded. A numerical model was employed to simulate the impact performance. This model has been accomplished by forming a user established subroutine (VUMAT) and executing it in ABAQUS software. Finally, the effect of CNTs amount on dynamic properties of laminated composites was discussed.

Using Numerical Modeling to Simulate Space Capsule Ground Landings

NASA Technical Reports Server (NTRS)

Heymsfield, Ernie; Fasanella, Edwin L.

2009-01-01

Experimental work is being conducted at the National Aeronautics and Space Administration s (NASA) Langley Research Center (LaRC) to investigate ground landing capabilities of the Orion crew exploration vehicle (CEV). The Orion capsule is NASA s replacement for the Space Shuttle. The Orion capsule will service the International Space Station and be used for future space missions to the Moon and to Mars. To evaluate the feasibility of Orion ground landings, a series of capsule impact tests are being performed at the NASA Langley Landing and Impact Research Facility (LandIR). The experimental results derived at LandIR provide means to validate and calibrate nonlinear dynamic finite element models, which are also being developed during this study. Because of the high cost and time involvement intrinsic to full-scale testing, numerical simulations are favored over experimental work. Subsequent to a numerical model validated by actual test responses, impact simulations will be conducted to study multiple impact scenarios not practical to test. Twenty-one swing tests using the LandIR gantry were conducted during the June 07 through October 07 time period to evaluate the Orion s impact response. Results for two capsule initial pitch angles, 0deg and -15deg , along with their computer simulations using LS-DYNA are presented in this article. A soil-vehicle friction coefficient of 0.45 was determined by comparing the test stopping distance with computer simulations. In addition, soil modeling accuracy is presented by comparing vertical penetrometer impact tests with computer simulations for the soil model used during the swing tests.

Impact of velocity space distribution on hybrid kinetic-magnetohydrodynamic simulation of the (1,1) mode

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Charlson C.

2008-07-15

Numeric studies of the impact of the velocity space distribution on the stabilization of (1,1) internal kink mode and excitation of the fishbone mode are performed with a hybrid kinetic-magnetohydrodynamic model. These simulations demonstrate an extension of the physics capabilities of NIMROD[C. R. Sovinec et al., J. Comput. Phys. 195, 355 (2004)], a three-dimensional extended magnetohydrodynamic (MHD) code, to include the kinetic effects of an energetic minority ion species. Kinetic effects are captured by a modification of the usual MHD momentum equation to include a pressure tensor calculated from the {delta}f particle-in-cell method [S. E. Parker and W. W. Lee,more » Phys. Fluids B 5, 77 (1993)]. The particles are advanced in the self-consistent NIMROD fields. We outline the implementation and present simulation results of energetic minority ion stabilization of the (1,1) internal kink mode and excitation of the fishbone mode. A benchmark of the linear growth rate and real frequency is shown to agree well with another code. The impact of the details of the velocity space distribution is examined; particularly extending the velocity space cutoff of the simulation particles. Modestly increasing the cutoff strongly impacts the (1,1) mode. Numeric experiments are performed to study the impact of passing versus trapped particles. Observations of these numeric experiments suggest that assumptions of energetic particle effects should be re-examined.« less

Impacts into quartz sand: Crater formation, shock metamorphism, and ejecta distribution in laboratory experiments and numerical models

NASA Astrophysics Data System (ADS)

Wünnemann, Kai; Zhu, Meng-Hua; Stöffler, Dieter

2016-10-01

We investigated the ejection mechanics by a complementary approach of cratering experiments, including the microscopic analysis of material sampled from these experiments, and 2-D numerical modeling of vertical impacts. The study is based on cratering experiments in quartz sand targets performed at the NASA Ames Vertical Gun Range. In these experiments, the preimpact location in the target and the final position of ejecta was determined by using color-coded sand and a catcher system for the ejecta. The results were compared with numerical simulations of the cratering and ejection process to validate the iSALE shock physics code. In turn the models provide further details on the ejection velocities and angles. We quantify the general assumption that ejecta thickness decreases with distance according to a power-law and that the relative proportion of shocked material in the ejecta increase with distance. We distinguish three types of shock metamorphic particles (1) melt particles, (2) shock lithified aggregates, and (3) shock-comminuted grains. The agreement between experiment and model was excellent, which provides confidence that the models can predict ejection angles, velocities, and the degree of shock loading of material expelled from a crater accurately if impact parameters such as impact velocity, impactor size, and gravity are varied beyond the experimental limitations. This study is relevant for a quantitative assessment of impact gardening on planetary surfaces and the evolution of regolith layers on atmosphereless bodies.

Impacts of the horizontal and vertical grids on the numerical solutions of the dynamical equations – Part 1: Nonhydrostatic inertia–gravity modes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Konor, Celal S.; Randall, David A.

We have used a normal-mode analysis to investigate the impacts of the horizontal and vertical discretizations on the numerical solutions of the nonhydrostatic anelastic inertia–gravity modes on a midlatitude f plane. The dispersion equations are derived from the linearized anelastic equations that are discretized on the Z, C, D, CD, (DC), A, E and B horizontal grids, and on the L and CP vertical grids. The effects of both horizontal grid spacing and vertical wavenumber are analyzed, and the role of nonhydrostatic effects is discussed. We also compare the results of the normal-mode analyses with numerical solutions obtained by runningmore » linearized numerical models based on the various horizontal grids. The sources and behaviors of the computational modes in the numerical simulations are also examined.Our normal-mode analyses with the Z, C, D, A, E and B grids generally confirm the conclusions of previous shallow-water studies for the cyclone-resolving scales (with low horizontal wavenumbers). We conclude that, aided by nonhydrostatic effects, the Z and C grids become overall more accurate for cloud-resolving resolutions (with high horizontal wavenumbers) than for the cyclone-resolving scales.A companion paper, Part 2, discusses the impacts of the discretization on the Rossby modes on a midlatitude β plane.« less

Impacts of the horizontal and vertical grids on the numerical solutions of the dynamical equations – Part 1: Nonhydrostatic inertia–gravity modes

DOE PAGES

Konor, Celal S.; Randall, David A.

2018-05-08

We have used a normal-mode analysis to investigate the impacts of the horizontal and vertical discretizations on the numerical solutions of the nonhydrostatic anelastic inertia–gravity modes on a midlatitude f plane. The dispersion equations are derived from the linearized anelastic equations that are discretized on the Z, C, D, CD, (DC), A, E and B horizontal grids, and on the L and CP vertical grids. The effects of both horizontal grid spacing and vertical wavenumber are analyzed, and the role of nonhydrostatic effects is discussed. We also compare the results of the normal-mode analyses with numerical solutions obtained by runningmore » linearized numerical models based on the various horizontal grids. The sources and behaviors of the computational modes in the numerical simulations are also examined.Our normal-mode analyses with the Z, C, D, A, E and B grids generally confirm the conclusions of previous shallow-water studies for the cyclone-resolving scales (with low horizontal wavenumbers). We conclude that, aided by nonhydrostatic effects, the Z and C grids become overall more accurate for cloud-resolving resolutions (with high horizontal wavenumbers) than for the cyclone-resolving scales.A companion paper, Part 2, discusses the impacts of the discretization on the Rossby modes on a midlatitude β plane.« less

Numerical modelling for quantitative environmental risk assessment for the disposal of drill cuttings and mud

NASA Astrophysics Data System (ADS)

Wahab, Mohd Amirul Faiz Abdul; Shaufi Sokiman, Mohamad; Parsberg Jakobsen, Kim

2017-10-01

To investigate the fate of drilling waste and their impacts towards surrounding environment, numerical models were generated using an environmental software; MIKE by DHI. These numerical models were used to study the transportation of suspended drill waste plumes in the water column and its deposition on seabed in South China Sea (SCS). A random disposal site with the model area of 50 km × 25 km was selected near the Madalene Shoal in SCS and the ambient currents as well as other meteorological conditions were simulated in details at the proposed location. This paper was focusing on sensitivity study of different drill waste particle characteristics on impacts towards marine receiving environment. The drilling scenarios were obtained and adapted from the oil producer well at offshore Sabah (Case 1) and data from actual exploration drilling case at Pumbaa location (PL 469) in the Norwegian Sea (Case 2). The two cases were compared to study the effect of different drilling particle characteristics and their behavior in marine receiving environment after discharged. Using the Hydrodynamic and Sediment Transport models simulated in MIKE by DHI, the variation of currents and the behavior of the drilling waste particles can be analyzed and evaluated in terms of multiple degree zones of impacts.

Numerical simulations of the occupant head response in an infantry vehicle under blunt impact and blast loading conditions.

PubMed

Sevagan, Gopinath; Zhu, Feng; Jiang, Binhui; Yang, King H

2013-07-01

This article presents the results of a finite element simulation on the occupant head response in an infantry vehicle under two separated loading conditions: (1) blunt impact and (2) blast loading conditions. A Hybrid-III dummy body integrated with a previously validated human head model was used as the surrogate. The biomechanical response of the head was studied in terms of head acceleration due to the impact by a projectile on the vehicle and intracranial pressure caused by blast wave. A series of parametric studies were conducted on the numerical model to analyze the effect of some key parameters, such as seat configuration, impact velocity, and boundary conditions. The simulation results indicate that a properly designed seat and internal surface of the infantry vehicle can play a vital role in reducing the risk of head injury in the current scenarios. Comparison of the kinematic responses under the blunt impact and blast loading conditions reveals that under the current loading conditions, the acceleration pulse in the blast scenario has much higher peak values and frequency than blunt impact case, which may reflect different head response characteristics.

NUMERICAL MODELS AS ENABLING TOOLS FOR TIDAL-STREAM ENERGY EXTRACTION AND ENVIRONMENTAL IMPACT ASSESSMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Zhaoqing; Wang, Taiping

This paper presents a modeling study conducted to evaluate tidal-stream energy extraction and its associated potential environmental impacts using a three-dimensional unstructured-grid coastal ocean model, which was coupled with a water-quality model and a tidal-turbine module.

Numerical modeling of seismic anomalies at impact craters on a laboratory scale

NASA Astrophysics Data System (ADS)

Wuennemann, K.; Grosse, C. U.; Hiermaier, S.; Gueldemeister, N.; Moser, D.; Durr, N.

2011-12-01

Almost all terrestrial impact craters exhibit a typical geophysical signature. The usually observed circular negative gravity anomaly and reduced seismic velocities in the vicinity of crater structures are presumably related to an approximately hemispherical zone underneath craters where rocks have experienced intense brittle plastic deformation and fracturing during formation (see Fig.1). In the framework of the "MEMIN" (multidisciplinary experimental and modeling impact crater research network) project we carried out hypervelocity cratering experiments at the Fraunhofer Institute for High-Speed Dynamics on a decimeter scale to study the spatiotemporal evolution of the damage zone using ultrasound, acoustic emission techniques, and numerical modeling of crater formation. 2.5-10 mm iron projectiles were shot at 2-5.5 km/s on dry and water-saturated sandstone targets. The target material was characterized before, during and after the impact with high spatial resolution acoustic techniques to detect the extent of the damage zone, the state of rocks therein and to record the growth of cracks. The ultrasound measurements are applied analog to seismic surveys at natural craters but used on a different - i.e. much smaller - scale. We compare the measured data with dynamic models of crater formation, shock, plastic and elastic wave propagation, and tensile/shear failure of rocks in the impacted sandstone blocks. The presence of porosity and pore water significantly affects the propagation of waves. In particular the crushing of pores due to shock compression has to be taken into account. We present preliminary results showing good agreement between experiments and numerical model. In a next step we plan to use the numerical models to upscale the results from laboratory dimensions to the scale of natural impact craters.

Exploring the impact of phonological awareness, visual-spatial working memory, and preschool quantity-number competencies on mathematics achievement in elementary school: findings from a 3-year longitudinal study.

PubMed

Krajewski, Kristin; Schneider, Wolfgang

2009-08-01

This longitudinal study explored the importance of kindergarten measures of phonological awareness, working memory, and quantity-number competencies (QNC) for predicting mathematical school achievement in third graders (mean age 8 years 8 months). It was found that the impact of phonological awareness and visual-spatial working memory, assessed at 5 years of age, was mediated by early QNC, which predicted math achievement in third grade. Importantly, and confirming our isolated number words hypothesis, phonological awareness had no impact on higher numerical competencies (i.e., when number words needed to be linked with quantities [QNC Level II and above]) but predicted basic numerical competencies (i.e., when number words were isolated from quantities [QNC Level I]), explaining the moderate relationship between early literacy development and the development of mathematical competencies.

FE Modelling of Tensile and Impact Behaviours of Squeeze Cast Magnesium Alloy AM60

NASA Astrophysics Data System (ADS)

DiCecco, Sante; Altenhof, William; Hu, Henry

In response to the need for reduced global emissions, the transportation industry has been steadily increasing the magnesium content in vehicles. This trend has resulted in experimental documentation of numerous alloy and casting combinations, while comparatively little work has been done regarding the development of numerical material models for vehicle crashworthiness simulations. In this study, material mechanical behaviour was implemented into an existing material model within the nonlinear FEA code LS-DYNA to emulate the mechanical behaviour of squeeze cast magnesium alloy AM60 with a relatively thick section of 10 mm thickness. Model validation was achieved by comparing the numerical and experimental results of a tensile test and Charpy impact event. Validation found an average absolute error of 5.44% between numerical and experimental tensile test data, whereas a relatively large discrepancy was found during Charpy evaluation. This discrepancy has been attributed to the presence of microstructure inhomogeneity in the squeeze cast magnesium alloy AM60.

Numerical and Experimental Studies on Crash Characteristics of Closed Form Thin—Walled Steel Sections

NASA Astrophysics Data System (ADS)

Veerasamy, M.; Srinivasan, K.; Prakash, Raghu V.

2010-10-01

The crash behavior of Cold Rolled Mild Steel (CRMS) closed form thin section was studied by conducting compressive tests at loading velocities of 5 mm/min and 1000 mm/min. The numerical simulations were conducted for the same experimental conditions to understand the deformation shape, peak forces and energy absorption capacity of sections at different impact velocities. The simulation results correlated well with the experimental results.

Numerical modeling of chemical spills and assessment of their environmental impacts

USDA-ARS?s Scientific Manuscript database

Chemical spills in surface water bodies often occur in modern societies, which cause significant impacts on water quality, eco-environment and drinking water safety. In this paper, chemical spill contamination in water resources was studied using a depth-integrated computational model, CCHE2D, for p...

Numerical Study of Head/Helmet Interaction Due to Blast Loading

DTIC Science & Technology

2014-10-01

unidirectional laminate sheets. The MAT_162 material model in LS-DYNA is used to account for the effects of strain rate and strain softening after damage...C., Tan V., Lee H., 2008, “Ballistic Impact of a KEVLAR Helmet: Experimental and Simulations”, International Journal of Impact Engineering, 35, pp

A Community-Scale Modeling System to Assess Port-Related Air Quality Impacts

EPA Science Inventory

Near-port air pollution has been identified by numerous organizations as a potential public health concern. Based upon multiple near-road and near-source monitoring studies, both busy roadways and large emission sources at the ports may impact local air quality within several hun...

Numerical modelling of vehicular pollution dispersion: The application of computational fluid dynamics techniques, a case study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vanderheyden, M.D.; Dajka, S.C.; Sinclair, R.

1997-12-31

Numerical modelling of vehicular emissions using the United States Environmental Protection Agency`s CALINE4 and CAL3QHC dispersion models to predict air quality impacts in the vicinity of roadways is a widely accepted means of evaluating vehicular emissions impacts. The numerical models account for atmospheric dispersion in both open or suburban terrains. When assessing roadways in urban areas with numerous large buildings, however, the models are unable to account for the complex airflows and therefore do not provide satisfactory estimates of pollutant concentrations. Either Wind Tunnel Modelling or Computational Fluid Dynamics (CFD) techniques can be used to assess the impact of vehiclemore » emissions in an urban core. This paper presents a case study where CFD is used to predict worst-case air quality impacts for two development configurations: an existing roadway configuration and a proposed configuration with an elevated pedestrian walkway. In assessing these configurations, worst-case meteorology and traffic conditions are modeled to allow for the prediction of pollutant concentrations due to vehicular emissions on two major streets in Hong Kong. The CFD modelling domain is divided up into thousands of control volumes. Each of these control volumes has a central point called a node where velocities, pollutant concentration and other auxiliary variables are calculated. The region of interest, the pedestrian link and its immediate surroundings, has a denser distribution of nodes in order to give a better resolution of local flow details. Separate CFD modelling runs were undertaken for each development configuration for wind direction increments of 15 degrees. For comparison of the development scenarios, pollutant concentrations (carbon monoxide, nitrogen dioxide and particulate matter) are predicted at up to 99 receptor nodes representing sensitive locations.« less

Numerical treatment for Carreau nanofluid flow over a porous nonlinear stretching surface

NASA Astrophysics Data System (ADS)

Eid, Mohamed R.; Mahny, Kasseb L.; Muhammad, Taseer; Sheikholeslami, Mohsen

2018-03-01

The impact of magnetic field and nanoparticles on the two-phase flow of a generalized non-Newtonian Carreau fluid over permeable non-linearly stretching surface has been analyzed in the existence of all suction/injection and thermal radiation. The governing PDEs with congruous boundary condition are transformed into a system of non-linear ODEs with appropriate boundary conditions by using similarity transformation. It solved numerically by using 4th-5th order Runge-Kutta-Fehlberg method based on shooting technique. The impacts of non-dimensional controlling parameters on velocity, temperature, and nanoparticles volume concentration profiles are scrutinized with aid of graphs. The Nusselt and the Sherwood numbers are studied at the different situations of the governing parameters. The numerical computations are in excellent consent with previously reported studies. It is found that the heat transfer rate is reduced with an increment of thermal radiation parameter and on contrary of the rising of magnetic field. The opposite trend happens in the mass transfer rate.

Numerical Modelling of Glass Fibre Reinforced Laminates Subjected to a Low Velocity Impact

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fan, J. Y.; Guana, Z. W.; Cantwell, W. J.

2010-05-21

This paper presents a series of numerical predictions of the perforation behaviour of glass fibre laminates subjected to quasi-static and low-velocity impact loading. Both shear and tensile failure criteria were used in the finite element models to simulate the post-failure processes via an automatic element removal procedure. The appropriate material properties, obtained through a series of uniaxial tension and bending tests on the composites, were used in the numerical models. Four, eight and sixteen ply glass fibre laminates panels were perforated at quasi-static rates and under low-velocity impact loading. Reasonably good correlation was obtained between the numerical simulations and themore » experimental results, both in terms of the failure modes and the load-deflection relationships before and during the penetration phase. The predicted impact energies of the GFRP panels were compared with the experimental data and reasonable agreement was observed.« less

Numerical Study on Deflection Behaviour of Concrete Beams Reinforced with GFRP Bars

NASA Astrophysics Data System (ADS)

Mohamed, Osama A.; Khattab, Rania; Hawat, Waddah Al

2017-10-01

Fiber-Reinforced Polymer (FRP) bars are gaining popularity as sustainable alternatives to conventional reinforcing steel bars in reinforced concrete applications. The production of FRP bars has lower environmental impact compared to steel reinforcing bars. In addition, the non-corroding FRP materials can potentially decrease the cost or need for maintenance of reinforced concrete structural elements, especially in harsh environmental conditions that can impact both concrete and reinforcement. FRP bars offer additional favourable properties including high tensile strength and low unit weight. However, the mechanical properties of FRP bars can lead to large crack widths and deflections. The objective of this study is to investigate the deflection behaviour of concrete beams reinforced with Glass FRP (GFRP) bars as a longitudinal main reinforcement. Six concrete beams reinforced with GFRP bars were modelled using the finite element computer program ANSYS. The main variable considered in the study is the reinforcement ratio. The deflection equations in current North American codes including ACI 440.1R-06, ACI 440.1R-15 and CSA S806-12 are used to compute deflections, and these are compared to numerical results. It was concluded in this paper that deflections predicted by ACI 440.1R-06 equations are lower than the numerical analysis results while ACI 440.1R-15 is in agreement with numerical analysis with tendency to be conservative. The values of deflections estimated by CSA S806-12 formulas are consistent with results of numerical analysis.

Quantifying a threat: Evidence of a numeric processing bias.

PubMed

Hamamouche, Karina A; Niemi, Laura; Cordes, Sara

2017-06-01

Humans prioritize the processing of threats over neutral stimuli; thus, not surprisingly, the presence of threats has been shown to alter performance on both perceptual and cognitive tasks. Yet whether the quantification process is disrupted in the presence of threat is unknown. In three experiments, we examined numerical estimation and discrimination abilities in adults in the context of threatening (spiders) and non-threatening (e.g., flowers) stimuli. Results of the numerical estimation task (Experiment 1) showed that participants underestimated the number of threatening relative to neutral stimuli. Additionally, numerical discrimination data reveal that participants' abilities to discriminate between the number of entities in two arrays were worsened when the arrays consisted of threatening entities versus neutral entities (Experiment 2). However, discrimination abilities were enhanced when threatening content was presented immediately before neutral dot arrays (Experiment 3). Together, these studies suggest that threats impact our processing of visual numerosity via changes in attention to numerical stimuli, and that the nature of the threat (intrinsic or extrinsic to the stimulus) is vital in determining the direction of this impact. Intrinsic threat content in stimuli impedes its own quantification; yet threat that is extrinsic to the sets to be enumerated enhances numerical processing for subsequently presented neutral stimuli. Copyright © 2017 Elsevier B.V. All rights reserved.

Transportation Investment and Job Creation in Minnesota Counties

DOT National Transportation Integrated Search

2018-01-01

Numerous studies have been conducted about the impact of transportation investment on economic development. These studies typically use a conventional production function model of economic development augmented by a public capital input, such as high...

Impact comparative study of phone carcasses behavior by FEM

NASA Astrophysics Data System (ADS)

Constantin, Cărăuşu; Plăvănescu, Simona; Dumitru, Nedelcu

2015-07-01

A constant concern of scientific research is based on plastics replace with biodegradable materials that reduce the adverse impact of waste on the environment. A biodegradable material that arouses interest lately is Arboform which is made of lignin, a component of wood and woody plants. Replacing plastic with Arboform in carrying components of products requires technical and economic studies on the implications of such replacement. Numerical simulation methods are a fast and economical way of analyzing the behavior of a product in various mechanical, thermal, electromagnetic and so on. The paper presents comparative results of numerical simulation using the software package SolidWorks impact behavior through the “Drop Test” of half shells made of High Density Polyethylene (HDPE) and of the Arboform LV3 Nature. Simulation watched the half-carcass behavior in three cases of accidental impact, “head”, “corner” and the “back side”. We analyzed the size and location of the maximum voltage and maximum deformation resulting from impact. Simulations have shown for all three cases a maximum voltage increase when using Arboform to use PEDH 93% for impact “forward” and “corner” and only 48.77% “back side” impact. If the maximum displacement, it increasing from carcasses of Arboform 4% for impact “head” and 6% for impact “corner”, but fell by 2.7% for the “back side” impact. The significant increase of stress can be attributed to the higher density of Arboform to PEDH, which led to different weights of the two half-carcasses.

Hydrodynamic Simulations of Giant Impacts

NASA Astrophysics Data System (ADS)

Reinhardt, Christian; Stadel, Joachim

2013-07-01

We studied the basic numerical aspects of giant impacts using Smoothed Particles Hydrodynamics (SPH), which has been used in most of the prior studies conducted in this area (e.g., Benz, Canup). Our main goal was to modify the massive parallel, multi-stepping code GASOLINE widely used in cosmological simulations so that it can properly simulate the behavior of condensed materials such as granite or iron using the Tillotson equation of state. GASOLINE has been used to simulate hundreds of millions of particles for ideal gas physics so that using several millions of particles in condensed material simulations seems possible. In order to focus our attention of the numerical aspects of the problem we neglected the internal structure of the protoplanets and modelled them as homogenous (isothermal) granite spheres. For the energy balance we only considered PdV work and shock heating of the material during the impact (neglected cooling of the material). Starting at a low resolution of 2048 particles for the target and the impactor we run several simulations for different impact parameters and impact velocities and successfully reproduced the main features of the pioneering work of Benz from 1986. The impact sends a shock wave through both bodies heating the target and disrupting the remaining impactor. As in prior simulations material is ejected from the collision. How much, and whether it leaves the system or survives in an orbit for a longer time, depends on the initial conditions but also on resolution. Increasing the resolution (to 1.2x10⁶ particles) results in both a much clearer shock wave and deformation of the bodies during the impact and a more compact and detailed "arm" like structure of the ejected material. Currently we are investigating some numerical issues we encountered and are implementing differentiated models, making one step closer to more realistic protoplanets in such giant impact simulations.

Teacher Beliefs and Intentions regarding the Instruction of English Grammar under National Curriculum Reforms: A Theory of Planned Behaviour Perspective

ERIC Educational Resources Information Center

Underwood, Paul R.

2012-01-01

While numerous studies in mainstream education have drawn on the Theory of Planned Behaviour to investigate curriculum impact, in English Language Teaching contexts such research is scant. This study applies the theory to anticipate the impact of the Japanese national curriculum for English, by exploring the beliefs of senior high school teachers…

Analytical and Numerical solutions of a nonlinear alcoholism model via variable-order fractional differential equations

NASA Astrophysics Data System (ADS)

Gómez-Aguilar, J. F.

2018-03-01

In this paper, we analyze an alcoholism model which involves the impact of Twitter via Liouville-Caputo and Atangana-Baleanu-Caputo fractional derivatives with constant- and variable-order. Two fractional mathematical models are considered, with and without delay. Special solutions using an iterative scheme via Laplace and Sumudu transform were obtained. We studied the uniqueness and existence of the solutions employing the fixed point postulate. The generalized model with variable-order was solved numerically via the Adams method and the Adams-Bashforth-Moulton scheme. Stability and convergence of the numerical solutions were presented in details. Numerical examples of the approximate solutions are provided to show that the numerical methods are computationally efficient. Therefore, by including both the fractional derivatives and finite time delays in the alcoholism model studied, we believe that we have established a more complete and more realistic indicator of alcoholism model and affect the spread of the drinking.

Evaluating aerosol impacts on Numerical Weather Prediction in two extreme dust and biomass-burning events

NASA Astrophysics Data System (ADS)

Remy, Samuel; Benedetti, Angela; Jones, Luke; Razinger, Miha; Haiden, Thomas

2014-05-01

The WMO-sponsored Working Group on Numerical Experimentation (WGNE) set up a project aimed at understanding the importance of aerosols for numerical weather prediction (NWP). Three cases are being investigated by several NWP centres with aerosol capabilities: a severe dust case that affected Southern Europe in April 2012, a biomass burning case in South America in September 2012, and an extreme pollution event in Beijing (China) which took place in January 2013. At ECMWF these cases are being studied using the MACC-II system with radiatively interactive aerosols. Some preliminary results related to the dust and the fire event will be presented here. A preliminary verification of the impact of the aerosol-radiation direct interaction on surface meteorological parameters such as 2m Temperature and surface winds over the region of interest will be presented. Aerosol optical depth (AOD) verification using AERONET data will also be discussed. For the biomass burning case, the impact of using injection heights estimated by a Plume Rise Model (PRM) for the biomass burning emissions will be presented.

Tailoring Interventions: Examining the Evidence and Identifying Gaps

ERIC Educational Resources Information Center

Gagliardi, Anna R.

2011-01-01

Introduction: Numerous population-based studies highlight the need to improve health care delivery and outcomes. Many single and combined interventions are available but their impact is limited and inconsistent. Tailoring may enhance their impact, but the best way to do so remains unclear. The purpose of this exploratory analysis was to identify…

A Methodological Framework for Studying Policy-Oriented Teacher Inquiry in Qualitative Research Contexts

ERIC Educational Resources Information Center

Koro-Ljungberg, Mirka

2014-01-01

System-based and collaborative teacher inquiry has unexplored potential that can impact educational policy in numerous ways. This impact can be increased when teacher inquiry builds momentum from classrooms and teaching practices and simultaneously addresses district, state, and national discourses and networks. In this conceptual paper, I…

Review of the dynamic behaviour of sports balls during normal and oblique impacts

NASA Astrophysics Data System (ADS)

Haron, Muhammad Adli; Jailani, Azrol; Abdullah, Nik Ahmad Faris Nik; Ismail, Rafis Suizwan; Rahim, Shayfull Zamree Abd; Ghazali, Mohd Fathullah

2017-09-01

In this paper are review of impact experiment to study the dynamic behaviour of sports ball during oblique and normal impacts. In previous studies, the investigation was done on the dynamic behaviour of a sports ball during oblique and normal impacts from experimental, numerical, and theoretical viewpoints. The experimental results are analysed and compared with the theories, in order to understand the dynamics behaviours based on the phenomenological occurrence. Throughout the experimental studies previously, there are results of dynamics behaviours examined by many researchers such as the coefficient of restitution, tangential coefficient, local deformation, dynamic impact force, contact time, angle of impact (inbound and rebound), spin rate of the ball, ball stiffness and damping coefficient which dependable of the initial or impact velocity.

Impact of a single drop on the same liquid: formation, growth and disintegration of jets

NASA Astrophysics Data System (ADS)

Agbaglah, G. Gilou; Deegan, Robert

2015-11-01

One of the simplest splashing scenarios results from the impact of a single drop on on the same liquid. The traditional understanding of this process is that the impact generates a jet that later breaks up into secondary droplets. Recently it was shown that even this simplest of scenarios is more complicated than expected because multiple jets can be generated from a single impact event and there are bifurcations in the multiplicity of jets. First, we study the formation, growth and disintegration of jets following the impact of a drop on a thin film of the same liquid using a combination of numerical simulations and linear stability theory. We obtain scaling relations from our simulations and use these as inputs to our stability analysis. We also use experiments and numerical simulations of a single drop impacting on a deep pool to examine the bifurcation from a single jet into two jets. Using high speed X-ray imaging methods we show that vortex separation within the drop leads to the formation of a second jet long after the formation of the ejecta sheet.

Numerical Evaluation of Dynamic Response for Flexible Composite Structures under Slamming Impact for Naval Applications

NASA Astrophysics Data System (ADS)

Hassoon, O. H.; Tarfaoui, M.; El Moumen, A.; Benyahia, H.; Nachtane, M.

2018-06-01

The deformable composite structures subjected to water-entry impact can be caused a phenomenon called hydroelastic effect, which can modified the fluid flow and estimated hydrodynamic loads comparing with rigid body. This is considered very important for ship design engineers to predict the global and the local hydrodynamic loads. This paper presents a numerical model to simulate the slamming water impact of flexible composite panels using an explicit finite element method. In order to better describe the hydroelastic influence and mechanical properties, composite materials panels with different stiffness and under different impact velocities with deadrise angle of 100 have been studied. In the other hand, the inertia effect was observed in the early stage of the impact that relative to the loading rate. Simulation results have been indicated that the lower stiffness panel has a higher hydroelastic effect and becomes more important when decreasing of the deadrise angle and increasing the impact velocity. Finally, the simulation results were compared with the experimental data and the analytical approaches of the rigid body to describe the behavior of the hydroelastic influence.

Numerical Evaluation of Dynamic Response for Flexible Composite Structures under Slamming Impact for Naval Applications

NASA Astrophysics Data System (ADS)

Hassoon, O. H.; Tarfaoui, M.; El Moumen, A.; Benyahia, H.; Nachtane, M.

2017-10-01

The deformable composite structures subjected to water-entry impact can be caused a phenomenon called hydroelastic effect, which can modified the fluid flow and estimated hydrodynamic loads comparing with rigid body. This is considered very important for ship design engineers to predict the global and the local hydrodynamic loads. This paper presents a numerical model to simulate the slamming water impact of flexible composite panels using an explicit finite element method. In order to better describe the hydroelastic influence and mechanical properties, composite materials panels with different stiffness and under different impact velocities with deadrise angle of 100 have been studied. In the other hand, the inertia effect was observed in the early stage of the impact that relative to the loading rate. Simulation results have been indicated that the lower stiffness panel has a higher hydroelastic effect and becomes more important when decreasing of the deadrise angle and increasing the impact velocity. Finally, the simulation results were compared with the experimental data and the analytical approaches of the rigid body to describe the behavior of the hydroelastic influence.

Graphene Nano-Composites for Hypervelocity Impact Applications

NASA Astrophysics Data System (ADS)

Manasrah, Alharith

The Low Earth Orbit (LEO) is a harsh environment cluttered with natural meteoroids and man-made debris, which can travel at velocities approaching 15 km/s. Most space activities within the LEO will encounter this environment. Thus, the spacecraft and its hardware must be designed to survive debris impact. This research introduces new procedures to produce a nano-composite material with mortar-brick nano-structure inspired from nacre. Nacre-like composites were successfully manufactured, based on three host polymers, with a wide range of graphene concentrations. The manufactured exfoliated graphene nano-platelet, embedded in a host polymer, provided good potential for enhancement of the hypervelocity impact (HVI) shield resistance. The nano-composites are suggested for use as a coating. Moreover, explicit dynamic finite element studies were conducted for further investigation of the hypervelocity impact of the graphene-based coatings in order to understand the effect of the coating on the crater formation and the exit velocity. This dissertation presents the results of the characterization and numerical sensitivity study of the developed material parameters. The numerical simulations were performed by implementing Autodyn smooth particle hydrodynamics. This study provides innovative, low-weight shielding enhancements for spacecraft, as well as other promising applications for the manufactured nano-composites.

Hypervelocity impact of mm-size plastic projectile on thin aluminum plate

NASA Astrophysics Data System (ADS)

Poniaev, S. A.; Kurakin, R. O.; Sedov, A. I.; Bobashev, S. V.; Zhukov, B. G.; Nechunaev, A. F.

2017-06-01

The experimental studies of the process of hypervelocity (up to 6 km/s) impact of a mm-size projectile on a thin aluminum plate is described. The numerical simulation of this process is presented. The data on the evolution, structure, and composition of the debris cloud formed as a result of the impact are reported. Basic specific features of the debris cloud formation are revealed.

The Impact of Numerical Control Technology and Computer Aided Manufacturing on Curriculum Development in Industrial Education and Technology. A Final Report.

ERIC Educational Resources Information Center

Bauch, Klaus Dieter

The study was designed to investigate the effects of Numerical Control Technology and Computer-Aided Manufacturing (NC/CAM) in American industry on industrial education and engineering technology education. The specific purpose was to identify a data base and rationale for curriculum development in NC/CAM through a comparison of views by…

A Numerical Study on Microwave Coagulation Therapy

DTIC Science & Technology

2013-01-01

hepatocellular carcinoma (small size liver tumor). Through extensive numerical simulations, we reveal the mathematical relationships between some critical parameters in the therapy, including input power, frequency, temperature, and regions of impact. It is shown that these relationships can be approximated using simple polynomial functions. Compared to solutions of partial differential equations, these functions are significantly easier to compute and simpler to analyze for engineering design and clinical

Discrete Particle Method for Simulating Hypervelocity Impact Phenomena.

PubMed

Watson, Erkai; Steinhauser, Martin O

2017-04-02

In this paper, we introduce a computational model for the simulation of hypervelocity impact (HVI) phenomena which is based on the Discrete Element Method (DEM). Our paper constitutes the first application of DEM to the modeling and simulating of impact events for velocities beyond 5 kms -1 . We present here the results of a systematic numerical study on HVI of solids. For modeling the solids, we use discrete spherical particles that interact with each other via potentials. In our numerical investigations we are particularly interested in the dynamics of material fragmentation upon impact. We model a typical HVI experiment configuration where a sphere strikes a thin plate and investigate the properties of the resulting debris cloud. We provide a quantitative computational analysis of the resulting debris cloud caused by impact and a comprehensive parameter study by varying key parameters of our model. We compare our findings from the simulations with recent HVI experiments performed at our institute. Our findings are that the DEM method leads to very stable, energy-conserving simulations of HVI scenarios that map the experimental setup where a sphere strikes a thin plate at hypervelocity speed. Our chosen interaction model works particularly well in the velocity range where the local stresses caused by impact shock waves markedly exceed the ultimate material strength.

Impact extractive fracture of jointed steel plates of a bolted joint

NASA Astrophysics Data System (ADS)

Daimaruya, M.; Fujiki, H.; Ambarita, H.

2012-08-01

This study is concerned with the development of a fracture criterion for the impact fracture of jointed steel plates of a bolted joint used in a car body. For the accurate prediction of crash characteristics of car bodies by computer-aided engineering (CAE), it is also necessary to examine the behavior and fracture of jointed steel plates subjected to impact loads. Although the actual impact fracture of jointed steel plates of a bolted joint used in cars is complicated, for simplifying the problem it might be classified into the shear fracture and the extractive fracture of jointed steel plates. Attention is given to the extractive fracture of jointed steel plates in this study. The extractive behavior and fracture of three kinds of steel plates used for cars are examined in experiments and numerical simulations. The impact extraction test of steel plates jointed by a bolt is performed using the one-bar method, together with the static test. In order to understand the mechanism of extractive fracture process of jointed steel plates, numerical simulations by a FEM code LS-DYNA are also carried out. The obtained results suggest that a stress-based fracture criterion may be developed for the impact extractive fracture of jointed steel plates of a bolted joint used in a car body.

Discrete Particle Method for Simulating Hypervelocity Impact Phenomena

PubMed Central

Watson, Erkai; Steinhauser, Martin O.

2017-01-01

In this paper, we introduce a computational model for the simulation of hypervelocity impact (HVI) phenomena which is based on the Discrete Element Method (DEM). Our paper constitutes the first application of DEM to the modeling and simulating of impact events for velocities beyond 5 kms−1. We present here the results of a systematic numerical study on HVI of solids. For modeling the solids, we use discrete spherical particles that interact with each other via potentials. In our numerical investigations we are particularly interested in the dynamics of material fragmentation upon impact. We model a typical HVI experiment configuration where a sphere strikes a thin plate and investigate the properties of the resulting debris cloud. We provide a quantitative computational analysis of the resulting debris cloud caused by impact and a comprehensive parameter study by varying key parameters of our model. We compare our findings from the simulations with recent HVI experiments performed at our institute. Our findings are that the DEM method leads to very stable, energy–conserving simulations of HVI scenarios that map the experimental setup where a sphere strikes a thin plate at hypervelocity speed. Our chosen interaction model works particularly well in the velocity range where the local stresses caused by impact shock waves markedly exceed the ultimate material strength. PMID:28772739

Traumatic eye injuries as a result of blunt impact: computational issues

NASA Astrophysics Data System (ADS)

Clemente, C.; Esposito, L.; Bonora, N.; Limido, J.; Lacome, J. L.; Rossi, T.

2014-05-01

The detachment or tearing of the retina in the human eye as a result of a collision is a phenomenon that occurs very often. Reliable numerical simulations of eye impact can be very useful tools to understand the physical mechanisms responsible for traumatic eye injuries accompanying blunt impact. The complexity and variability of the physical and mechanical properties of the biological materials, the lack of agreement on their related experimental data as well as the unsuitability of specific numerical codes and models are only some of the difficulties when dealing with this matter. All these challenging issues must be solved to obtain accurate numerical analyses involving dynamic behavior of biological soft tissues. To this purpose, a numerical and experimental investigation of the dynamic response of the eye during an impact event was performed. Numerical simulations were performed with IMPETUS-AFEA, a new general non-linear finite element (FE) software which offers non uniform rational B-splines (NURBS) FE technology for the simulation of large deformation and fracture in materials. IMPETUS code was selected in order to solve hourglass and locking problems typical of nearly incompressible materials like eye tissues. Computational results were compared with the experimental results on fresh enucleated porcine eyes impacted with airsoft pellets.

Impacts of air pollution exposure on the allergenic properties of Arizona cypress pollens

NASA Astrophysics Data System (ADS)

Shahali, Y.; Pourpak, Z.; Moin, M.; Zare, A.; Majd, A.

2009-02-01

Epidemiological studies have demonstrated that urbanization and high levels of vehicle emissions correlated with the increasing trend of pollen-induced respiratory allergies. Numerous works have investigated the role of pollutants in the pathogenesis of respiratory diseases but impacts of anthropogenic pollution on pollen allergenic properties are still poorly understood. The objective of this survey was to evaluate impacts of the traffic-related pollution on the structure and allergenic protein content of Arizona cypress (Cupressus arizonica, CA) pollens, recognized as a rising cause of seasonal allergy in various regions worldwide. According to our results, traffic-related air pollution by its direct effects on the elemental composition of pollens considerably increased the fragility of the pollen exine, causing numerous cracks in its surface and facilitating pollen content liberation. Pollen grains were also covered by numerous submicronic orbicules which may act as effective vectors for pollen-released components into the lower regions of respiratory organs. On the other hand, this study provides us reliable explications about the low efficiency of standard commercial allergens in the diagnosis of the Arizona cypress pollen allergy in Tehran. Although traffic related pollution affects the allergenic components of CA pollens, the repercussions on the respiratory health of urban populations have yet to be clarified and need further investigations.

Results of the Workshop on Impact Cratering: Bridging the Gap Between Modeling and Observations

NASA Technical Reports Server (NTRS)

Herrick, Robert (Editor); Pierazzo, Elisabetta (Editor)

2003-01-01

On February 7-9,2003, approximately 60 scientists gathered at the Lunar and Planetary Institute in Houston, Texas, for a workshop devoted to improving knowledge of the impact cratering process. We (co-conveners Elisabetta Pierazzo and Robert Herrick) both focus research efforts on studying the impact cratering process, but the former specializes in numerical modeling while the latter draws inferences from observations of planetary craters. Significant work has been done in several key areas of impact studies over the past several years, but in many respects there seem to be a disconnect between the groups employing different approaches, in particular modeling versus observations. The goal in convening this workshop was to bring together these disparate groups to have an open dialogue for the purposes of answering outstanding questions about the impact process and setting future research directions. We were successful in getting participation from most of the major research groups studying the impact process. Participants gathered from five continents with research specialties ranging from numerical modeling to field geology, and from small-scale experimentation and geochemical sample analysis to seismology and remote sensing.With the assistance of the scientific advisory committee (Bevan French, Kevin Housen, Bill McKinnon, Jay Melosh, and Mike Zolensky), the workshop was divided into a series of sessions devoted to different aspects of the cratering process. Each session was opened by two invited t a b , one given by a specialist in numerical or experimental modeling approaches, and the other by a specialist in geological, geophysical, or geochemical observations. Shorter invited and contributed talks filled out the sessions, which were then concluded with an open discussion time. All modelers were requested to address the question of what observations would better constrain their models, and all observationists were requested to discuss how their observations can constrain modeling efforts.

Melting and its relationship to impact crater morphology

NASA Technical Reports Server (NTRS)

Okeefe, John D.; Ahrens, Thomas J.

1992-01-01

Shock-melting features occur on planets at scales that range from micrometers to megameters. It is the objective of this study to determine the extent of thickness, volume geometry of the melt, and relationship with crater morphology. The variation in impact crater morphology on planets is influenced by a broad range of parameters: e.g., planetary density, thermal state, strength, impact velocity, gravitational acceleration. We modeled the normal impact of spherical projectiles on a semi-infinite planet over a broad range of conditions using numerical techniques.

Numerical study of impact erosion of multiple solid particle

NASA Astrophysics Data System (ADS)

Zheng, Chao; Liu, Yonghong; Chen, Cheng; Qin, Jie; Ji, Renjie; Cai, Baoping

2017-11-01

Material erosion caused by continuous particle impingement during hydraulic fracturing results in significant economic loss and increased production risks. The erosion process is complex and has not been clearly explained through physical experiments. To address this problem, a multiple particle model in a 3D configuration was proposed to investigate the dynamic erosion process. This approach can significantly reduce experiment costs. The numerical model considered material damping and elastic-plastic material behavior of target material. The effects of impact parameters on erosion characteristics, such as plastic deformation, contact time, and energy loss rate, were investigated. Based on comprehensive studies, the dynamic erosion mechanism and geometry evolution of eroded crater was obtained. These findings can provide a detailed erosion process of target material and insights into the material erosion caused by multiple particle impingement.

Improved Impact of Atmospheric Infrared Sounder (AIRS) Radiance Assimilation in Numerical Weather Prediction

NASA Technical Reports Server (NTRS)

Zavodsky, Bradley; Chou, Shih-Hung; Jedlovec, Gary

2012-01-01

Improvements to global and regional numerical weather prediction (NWP) have been demonstrated through assimilation of data from NASA s Atmospheric Infrared Sounder (AIRS). Current operational data assimilation systems use AIRS radiances, but impact on regional forecasts has been much smaller than for global forecasts. Retrieved profiles from AIRS contain much of the information that is contained in the radiances and may be able to reveal reasons for this reduced impact. Assimilating AIRS retrieved profiles in an identical analysis configuration to the radiances, tracking the quantity and quality of the assimilated data in each technique, and examining analysis increments and forecast impact from each data type can yield clues as to the reasons for the reduced impact. By doing this with regional scale models individual synoptic features (and the impact of AIRS on these features) can be more easily tracked. This project examines the assimilation of hyperspectral sounder data used in operational numerical weather prediction by comparing operational techniques used for AIRS radiances and research techniques used for AIRS retrieved profiles. Parallel versions of a configuration of the Weather Research and Forecasting (WRF) model with Gridpoint Statistical Interpolation (GSI) that mimics the analysis methodology, domain, and observational datasets for the regional North American Mesoscale (NAM) model run at the National Centers for Environmental Prediction (NCEP)/Environmental Modeling Center (EMC) are run to examine the impact of each type of AIRS data set. The first configuration will assimilate the AIRS radiance data along with other conventional and satellite data using techniques implemented within the operational system; the second configuration will assimilate AIRS retrieved profiles instead of AIRS radiances in the same manner. Preliminary results of this study will be presented and focus on the analysis impact of the radiances and profiles for selected cases.

Numerical study of the impact response of woodpecker's head

NASA Astrophysics Data System (ADS)

Zhu, Zhao Dan; Ma, Guo Jun; Wu, Cheng Wei; Chen, Zhen

2012-12-01

Woodpecker can beat trees 20-25 times per second and lasts for several seconds, with a 1200 g deceleration, but it appears that they never get brain concussion. How does the stress wave propagate from the beak tip to brain and how does a woodpecker protect itself from brain damage? In this paper, we establish a finite element model of typical woodpecker head based on its X-ray tomography images and conduct the numerical analysis of the impact response of the woodpecker's head by using a viscoelasticity material model. Especially, the woodpecker head response to an impact speed of 7 m/s is investigated to explore the stress concentration zone and how the stress wave propagates in its head. The numerical results show that the stress wave in the head propagates from the upper beak to back skull and is reduced by the specific structure of hyoid and viscoelasticity of biomaterials. The maximum stresses in skull and brain are both below the safe level. The stress in skull almost disappears before the next impact. The stress in brain lasts for a little longer but shows smaller value with little variation. The stress is impossible to accumulate in the limited pecking time, so the brain damage can be avoided.

Consequences of the dynamic triple peak impact factor in Traumatic Brain Injury as Measured with Numerical Simulation.

PubMed

von Holst, Hans; Li, Xiaogai

2013-01-01

There is a lack of knowledge about the direct neuromechanical consequences in traumatic brain injury (TBI) at the scene of accident. In this study we use a finite element model of the human head to study the dynamic response of the brain during the first milliseconds after the impact with velocities of 10, 6, and 2 meters/second (m/s), respectively. The numerical simulation was focused on the external kinetic energy transfer, intracranial pressure (ICP), strain energy density and first principal strain level, and their respective impacts to the brain tissue. We show that the oblique impacts of 10 and 6 m/s resulted in substantial high peaks for the ICP, strain energy density, and first principal strain levels, however, with different patterns and time frames. Also, the 2 m/s impact showed almost no increase in the above mentioned investigated parameters. More importantly, we show that there clearly exists a dynamic triple peak impact factor to the brain tissue immediately after the impact regardless of injury severity associated with different impact velocities. The dynamic triple peak impacts occurred in a sequential manner first showing strain energy density and ICP and then followed by first principal strain. This should open up a new dimension to better understand the complex mechanisms underlying TBI. Thus, it is suggested that the combination of the dynamic triple peak impacts to the brain tissue may interfere with the cerebral metabolism relative to the impact severity thereby having the potential to differentiate between severe and moderate TBI from mild TBI.

An Introduction to Numerical Control. Problems for Numerical Control Part Programming.

ERIC Educational Resources Information Center

Campbell, Clifton P.

This combination text and workbook is intended to introduce industrial arts students to numerical control part programming. Discussed in the first section are the impact of numerical control, training efforts, numerical control in established programs, related information for drafting, and the Cartesian Coordinate System and dimensioning…

Combustion characteristics and turbulence modeling of swirling reacting flow in solid fuel ramjet

NASA Astrophysics Data System (ADS)

Musa, Omer; Xiong, Chen; Changsheng, Zhou

2017-10-01

This paper reviews the historical studies have been done on the solid-fuel ramjet engine and difficulties associated with numerical modeling of swirling flow with combustible gases. A literature survey about works related to numerical and experimental investigations on solid-fuel ramjet as well as using swirling flow and different numerical approaches has been provided. An overview of turbulence modeling of swirling flow and the behavior of turbulence at streamline curvature and system rotation are presented. A new and simple curvature/correction factor is proposed in order to reduce the programming complexity of SST-CC turbulence model. Finally, numerical and experimental investigations on the impact of swirling flow on SFRJ have been carried out. For that regard, a multi-physics coupling code is developed to solve the problems of multi-physics coupling of fluid mechanics, solid pyrolysis, heat transfer, thermodynamics, and chemical kinetics. The connected-pipe test facility is used to carry out the experiments. The results showed a positive impact of swirling flow on SFRJ along with, three correlations are proposed.

Numerical Investigation on Head and Brain Injuries Caused by Windshield Impact on Riders Using Electric Self-Balancing Scooters

PubMed Central

Zheng, Yanting; Shen, Ming; Yang, Xianfeng

2018-01-01

To investigate head-brain injuries caused by windshield impact on riders using electric self-balancing scooters (ESS). Numerical vehicle ESS crash scenarios are constructed by combining the finite element (FE) vehicle model and multibody scooter/rider models. Impact kinematic postures of the head-windshield contact under various impact conditions are captured. Then, the processes during head-windshield contact are reconstructed using validated FE head/laminated windshield models to assess the severity of brain injury caused by the head-windshield contact. Governing factors, such as vehicle speed, ESS speed, and the initial orientation of ESS rider, have nontrivial influences over the severity of a rider's brain injuries. Results also show positive correlations between vehicle speed and head-windshield impact speeds (linear and angular). Meanwhile, the time of head-windshield contact happens earlier when the vehicle speed is faster. According to the intensive study, windshield-head contact speed (linear and angular), impact location on the windshield, and head collision area are found to be direct factors on ESS riders' brain injuries during an impact. The von Mises stress and shear stress rise when relative contact speed of head-windshield increases. Brain injury indices vary widely when the head impacting the windshield from center to the edge or impacting with different areas. PMID:29770161

Investigation on low velocity impact resistance of SMA composite material

NASA Astrophysics Data System (ADS)

Hu, Dianyin; Zhang, Long; Wang, Rongqiao; Zhang, Xiaoyong

2016-04-01

A method to improve low velocity impact resistance of aeroengine composite casing using shape memory alloy's properties of shape memory(SM) and super-elasticity(SE) is proposed in this study. Firstly, a numerical modeling of SMA reinforced composite laminate under low velocity impact load with impact velocity of 10 m/s is established based on its constitutive model implemented by the VUMAT subroutine of commercial software ABAQUS. Secondly, the responses of SMA composite laminate including stress and deflection distributions were achieved through transient analysis under low velocity impact load. Numerical results show that both peak stress and deflection values of SMA composite laminate are less than that without SMA, which proves that embedding SMA into the composite structure can effectively improve the low velocity impact performance of composite structure. Finally, the influence of SM and SE on low velocity impact resistance is quantitatively investigated. The values of peak stress and deflection of SMA composite based on SM property decrease by 18.28% and 9.43% respectively, compared with those without SMA, instead of 12.87% and 5.19% based on SE. In conclusion, this proposed model described the impact damage of SMA composite structure and turned to be a more beneficial method to enhance the impact resistance by utilizing SM effect.

Effects of solid barriers on dispersion of roadway emissions

EPA Science Inventory

Several studies have found that exposure to traffic-generated air pollution is associated with several adverse health effects. Field studies, laboratory experiments, and numerical simulations indicate that roadside barriers represent a practical method of mitigating the impact of...

Coefficient of restitution in fractional viscoelastic compliant impacts using fractional Chebyshev collocation

NASA Astrophysics Data System (ADS)

Dabiri, Arman; Butcher, Eric A.; Nazari, Morad

2017-02-01

Compliant impacts can be modeled using linear viscoelastic constitutive models. While such impact models for realistic viscoelastic materials using integer order derivatives of force and displacement usually require a large number of parameters, compliant impact models obtained using fractional calculus, however, can be advantageous since such models use fewer parameters and successfully capture the hereditary property. In this paper, we introduce the fractional Chebyshev collocation (FCC) method as an approximation tool for numerical simulation of several linear fractional viscoelastic compliant impact models in which the overall coefficient of restitution for the impact is studied as a function of the fractional model parameters for the first time. Other relevant impact characteristics such as hysteresis curves, impact force gradient, penetration and separation depths are also studied.

The Impact of Term-Time Employment on Higher Education Students' Academic Attainment and Achievement

ERIC Educational Resources Information Center

Callender, Claire

2008-01-01

Term-time employment among Britain's undergraduates is a growing phenomenon but it has received scant attention from government and policy makers. Although there are numerous studies on the subject, few have explored the impact of term-time employment on students' actual attainment and those that have are limited. This article attempts to fill…

Impact of Typhoons on the Western Pacific Ocean (ITOP) DRI: Numerical Modeling of Ocean Mixed Layer Turbulence and Entrainment at High Winds

DTIC Science & Technology

2013-09-30

1 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Impact of Typhoons on the Western Pacific Ocean (ITOP...The measurement and modeling activities include a focus on the impact of surface waves, air-sea fluxes and the temperature, salinity and velocity...SUBTITLE Impact of Typhoons on the Western Pacific Ocean (ITOP) DRI: Numerical Modeling of Ocean Mixed Layer Turbulence and Entrainment at High Winds

Ancient numerical daemons of conceptual hydrological modeling: 1. Fidelity and efficiency of time stepping schemes

NASA Astrophysics Data System (ADS)

Clark, Martyn P.; Kavetski, Dmitri

2010-10-01

A major neglected weakness of many current hydrological models is the numerical method used to solve the governing model equations. This paper thoroughly evaluates several classes of time stepping schemes in terms of numerical reliability and computational efficiency in the context of conceptual hydrological modeling. Numerical experiments are carried out using 8 distinct time stepping algorithms and 6 different conceptual rainfall-runoff models, applied in a densely gauged experimental catchment, as well as in 12 basins with diverse physical and hydroclimatic characteristics. Results show that, over vast regions of the parameter space, the numerical errors of fixed-step explicit schemes commonly used in hydrology routinely dwarf the structural errors of the model conceptualization. This substantially degrades model predictions, but also, disturbingly, generates fortuitously adequate performance for parameter sets where numerical errors compensate for model structural errors. Simply running fixed-step explicit schemes with shorter time steps provides a poor balance between accuracy and efficiency: in some cases daily-step adaptive explicit schemes with moderate error tolerances achieved comparable or higher accuracy than 15 min fixed-step explicit approximations but were nearly 10 times more efficient. From the range of simple time stepping schemes investigated in this work, the fixed-step implicit Euler method and the adaptive explicit Heun method emerge as good practical choices for the majority of simulation scenarios. In combination with the companion paper, where impacts on model analysis, interpretation, and prediction are assessed, this two-part study vividly highlights the impact of numerical errors on critical performance aspects of conceptual hydrological models and provides practical guidelines for robust numerical implementation.

An efficient numerical algorithm for transverse impact problems

NASA Technical Reports Server (NTRS)

Sankar, B. V.; Sun, C. T.

1985-01-01

Transverse impact problems in which the elastic and plastic indentation effects are considered, involve a nonlinear integral equation for the contact force, which, in practice, is usually solved by an iterative scheme with small increments in time. In this paper, a numerical method is proposed wherein the iterations of the nonlinear problem are separated from the structural response computations. This makes the numerical procedures much simpler and also efficient. The proposed method is applied to some impact problems for which solutions are available, and they are found to be in good agreement. The effect of the magnitude of time increment on the results is also discussed.

Numerical Simulation of Ballistic Impact on Particulate Composite Target using Discrete Element Method: 1-D and 2-D Models

NASA Astrophysics Data System (ADS)

Nair, Rajesh P.; Lakshmana Rao, C.

2014-01-01

Ballistic impact (BI) is a study that deals with a projectile hitting a target and observing its effects in terms of deformation and fragmentation of the target. The Discrete Element Method (DEM) is a powerful numerical technique used to model solid and particulate media. Here, an attempt is made to simulate the BI process using DEM. 1-D DEM for BI is developed and depth of penetration (DOP) is obtained. The DOP is compared with results obtained from 2-D DEM. DEM results are found to match empirical results. Effects of strain rate sensitivity of the material response on DOP are also simulated.

Numerical analysis of partially molten splat during thermal spray process using the finite element method

NASA Astrophysics Data System (ADS)

Zirari, M.; Abdellah El-Hadj, A.; Bacha, N.

2010-03-01

A finite element method is used to simulate the deposition of the thermal spray coating process. A set of governing equations is solving by a volume of fluid method. For the solidification phenomenon, we use the specific heat method (SHM). We begin by comparing the present model with experimental and numerical model available in the literature. In this study, completely molten or semi-molten aluminum particle impacts a H13 tool steel substrate is considered. Next we investigate the effect of inclination of impact of a partially molten particle on flat substrate. It was found that the melting state of the particle has great effects on the morphologies of the splat.

Head injury assessment of non-lethal projectile impacts: A combined experimental/computational method.

PubMed

Sahoo, Debasis; Robbe, Cyril; Deck, Caroline; Meyer, Frank; Papy, Alexandre; Willinger, Remy

2016-11-01

The main objective of this study is to develop a methodology to assess this risk based on experimental tests versus numerical predictive head injury simulations. A total of 16 non-lethal projectiles (NLP) impacts were conducted with rigid force plate at three different ranges of impact velocity (120, 72 and 55m/s) and the force/deformation-time data were used for the validation of finite element (FE) NLP. A good accordance between experimental and simulation data were obtained during validation of FE NLP with high correlation value (>0.98) and peak force discrepancy of less than 3%. A state-of-the art finite element head model with enhanced brain and skull material laws and specific head injury criteria was used for numerical computation of NLP impacts. Frontal and lateral FE NLP impacts to the head model at different velocities were performed under LS-DYNA. It is the very first time that the lethality of NLP is assessed by axonal strain computation to predict diffuse axonal injury (DAI) in NLP impacts to head. In case of temporo-parietal impact the min-max risk of DAI is 0-86%. With a velocity above 99.2m/s there is greater than 50% risk of DAI for temporo-parietal impacts. All the medium- and high-velocity impacts are susceptible to skull fracture, with a percentage risk higher than 90%. This study provides tool for a realistic injury (DAI and skull fracture) assessment during NLP impacts to the human head. Copyright © 2016 Elsevier Ltd. All rights reserved.

Reduced order models for prediction of groundwater quality impacts from CO₂ and brine leakage

DOE PAGES

Zheng, Liange; Carroll, Susan; Bianchi, Marco; ...

2014-12-31

A careful assessment of the risk associated with geologic CO₂ storage is critical to the deployment of large-scale storage projects. A potential risk is the deterioration of groundwater quality caused by the leakage of CO₂ and brine leakage from deep subsurface reservoirs. In probabilistic risk assessment studies, numerical modeling is the primary tool employed to assess risk. However, the application of traditional numerical models to fully evaluate the impact of CO₂ leakage on groundwater can be computationally complex, demanding large processing times and resources, and involving large uncertainties. As an alternative, reduced order models (ROMs) can be used as highlymore » efficient surrogates for the complex process-based numerical models. In this study, we represent the complex hydrogeological and geochemical conditions in a heterogeneous aquifer and subsequent risk by developing and using two separate ROMs. The first ROM is derived from a model that accounts for the heterogeneous flow and transport conditions in the presence of complex leakage functions for CO₂ and brine. The second ROM is obtained from models that feature similar, but simplified flow and transport conditions, and allow for a more complex representation of all relevant geochemical reactions. To quantify possible impacts to groundwater aquifers, the basic risk metric is taken as the aquifer volume in which the water quality of the aquifer may be affected by an underlying CO₂ storage project. The integration of the two ROMs provides an estimate of the impacted aquifer volume taking into account uncertainties in flow, transport and chemical conditions. These two ROMs can be linked in a comprehensive system level model for quantitative risk assessment of the deep storage reservoir, wellbore leakage, and shallow aquifer impacts to assess the collective risk of CO₂ storage projects.« less

Stochastic responses of Van der Pol vibro-impact system with fractional derivative damping excited by Gaussian white noise.

PubMed

Xiao, Yanwen; Xu, Wei; Wang, Liang

2016-03-01

This paper focuses on the study of the stochastic Van der Pol vibro-impact system with fractional derivative damping under Gaussian white noise excitation. The equations of the original system are simplified by non-smooth transformation. For the simplified equation, the stochastic averaging approach is applied to solve it. Then, the fractional derivative damping term is facilitated by a numerical scheme, therewith the fourth-order Runge-Kutta method is used to obtain the numerical results. And the numerical simulation results fit the analytical solutions. Therefore, the proposed analytical means to study this system are proved to be feasible. In this context, the effects on the response stationary probability density functions (PDFs) caused by noise excitation, restitution condition, and fractional derivative damping are considered, in addition the stochastic P-bifurcation is also explored in this paper through varying the value of the coefficient of fractional derivative damping and the restitution coefficient. These system parameters not only influence the response PDFs of this system but also can cause the stochastic P-bifurcation.

Stochastic responses of Van der Pol vibro-impact system with fractional derivative damping excited by Gaussian white noise

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiao, Yanwen; Xu, Wei, E-mail: weixu@nwpu.edu.cn; Wang, Liang

2016-03-15

This paper focuses on the study of the stochastic Van der Pol vibro-impact system with fractional derivative damping under Gaussian white noise excitation. The equations of the original system are simplified by non-smooth transformation. For the simplified equation, the stochastic averaging approach is applied to solve it. Then, the fractional derivative damping term is facilitated by a numerical scheme, therewith the fourth-order Runge-Kutta method is used to obtain the numerical results. And the numerical simulation results fit the analytical solutions. Therefore, the proposed analytical means to study this system are proved to be feasible. In this context, the effects onmore » the response stationary probability density functions (PDFs) caused by noise excitation, restitution condition, and fractional derivative damping are considered, in addition the stochastic P-bifurcation is also explored in this paper through varying the value of the coefficient of fractional derivative damping and the restitution coefficient. These system parameters not only influence the response PDFs of this system but also can cause the stochastic P-bifurcation.« less

An Approach to Developing Numeric Water Quality Criteria for Using the SeaWiFS Satellite Data Record

EPA Science Inventory

Human activities on land increase nutrient loads to coastal waters, which can increase phytoplankton production and biomass and associated ecological impacts. Numeric nutrient water quality standards were needed to protect coastal waters from eutrophication impacts. The Environm...

The Effect of Disturbances and Surrounding Air on the Droplet Impact Phenomena

NASA Astrophysics Data System (ADS)

Work, Andrew; Lian, Yongsheng; Sussman, Mark

2013-11-01

Supercooled Large Droplets (SLDs) represent an icing hazard in a number of areas, most obviously in aviation. SLDs pose a hazard above smaller supercooled droplets because they don't freeze completely on impact, and can spread or splash. Experiments have demonstrated that surrounding air plays an important role in the droplet impact phenomena: a low ambient pressure can suppress the droplet splashing. However, the effect of surrounding air on the droplet impact has not been adequately addressed. Numerical simulations are conducted to systematically investigate the interplay between the droplet and the surrounding air in the droplet splashing regime. Disturbances originating from the experimental droplet generator are also studied in the simulation. We investigate whether these disturbances are responsible for the fingering observed in experimentation. We compare the results of several perturbations on the droplet, as well as the effect of surface roughness. Simulations are conducted using the Moment of Fluid numerical method, and the grid features adaptive mesh refinement.

An overview of the South Atlantic Ocean climate variability and air-sea interaction processes

NASA Astrophysics Data System (ADS)

Pezzi, L. P.; Parise, C. K.; Souza, R.; Gherardi, D. F.; Camargo, R.; Soares, H. C.; Silveira, I.

2013-05-01

The Ocean Modeling Group at the National Institute of Space Research (INPE) in Brazil has been developing several studies to understand the role of the Atlantic ocean on the South America climate. Studies include simulating the dynamics of the Tropical South-Atlantic Ocean and Southern Ocean. This is part of an ongoing international cooperation, in which Brazil participates with in situ observations, numerical modeling and statistical analyses. We have focused on the understanding of the impacts of extreme weather events over the Tropical South Atlantic Ocean and their prediction on different time-scales. One such study is aimed at analyzing the climate signal generated by imposing an extreme condition on the Antarctic sea ice and considering different complexities of the sea ice model. The influence of the Brazil-Malvinas Confluence (BMC) region on the marine atmospheric boundary layer (MABL) is also investigated through in situ data analysis of different cruises and numerical experiments with a regional numerical model. There is also an ongoing investigation that revealed basin-scale interannual climate variation with impacts on the Brazilian Large Marine Ecosystems (LMEs), which are strongly correlated with climate indices such as ENSO, AAO and PDO.

Soft impacts on aerospace structures

NASA Astrophysics Data System (ADS)

Abrate, Serge

2016-02-01

This article provides an overview of the literature dealing with three types of soft impacts of concern for the aerospace applications, namely impacts of rain drops, hailstones and birds against aircraft. It describes the physics of the problem as it has become better understood through experiments, analyses, and numerical simulations. Some emphasis has been placed on the material models and the numerical approaches used in modeling these three types of projectiles.

Arithmetic and algebraic problem solving and resource allocation: the distinct impact of fluid and numerical intelligence.

PubMed

Dix, Annika; van der Meer, Elke

2015-04-01

This study investigates cognitive resource allocation dependent on fluid and numerical intelligence in arithmetic/algebraic tasks varying in difficulty. Sixty-six 11th grade students participated in a mathematical verification paradigm, while pupil dilation as a measure of resource allocation was collected. Students with high fluid intelligence solved the tasks faster and more accurately than those with average fluid intelligence, as did students with high compared to average numerical intelligence. However, fluid intelligence sped up response times only in students with average but not high numerical intelligence. Further, high fluid but not numerical intelligence led to greater task-related pupil dilation. We assume that fluid intelligence serves as a domain-general resource that helps to tackle problems for which domain-specific knowledge (numerical intelligence) is missing. The allocation of this resource can be measured by pupil dilation. Copyright © 2014 Society for Psychophysiological Research.

Neck muscle load distribution in lateral, frontal, and rear-end impacts: a three-dimensional finite element analysis.

PubMed

Hedenstierna, Sofia; Halldin, Peter; Siegmund, Gunter P

2009-11-15

A finite element (FE) model of the human neck was used to study the distribution of neck muscle loads during multidirectional impacts. The computed load distributions were compared to experimental electromyography (EMG) recordings. To quantify passive muscle loads in nonactive cervical muscles during impacts of varying direction and energy, using a three-dimensional (3D) continuum FE muscle model. Experimental and numerical studies have confirmed the importance of muscles in the impact response of the neck. Although EMG has been used to measure the relative activity levels in neck muscles during impact tests, this technique has not been able to measure all neck muscles and cannot directly quantify the force distribution between the muscles. A numerical model can give additional insight into muscle loading during impact. An FE model with solid element musculature was used to simulate frontal, lateral, and rear-end vehicle impacts at 4 peak accelerations. The peak cross-sectional forces, internal energies, and effective strains were calculated for each muscle and impact configuration. The computed load distribution was compared with experimental EMG data. The load distribution in the cervical muscles varied with load direction. Peak sectional forces, internal energies, and strains increased in most muscles with increasing impact acceleration. The dominant muscles identified by the model for each direction were splenius capitis, levator scapulae, and sternocleidomastoid in lateral impacts, splenius capitis, and trapezoid in frontal impacts, and sternocleidomastoid, rectus capitis posterior minor, and hyoids in rear-end impacts. This corresponded with the most active muscles identified by EMG recordings, although within these muscles the distribution of forces and EMG levels were not the same. The passive muscle forces, strains, and energies computed using a continuum FE model of the cervical musculature distinguished between impact directions and peak accelerations, and on the basis of prior studies, isolated the most important muscles for each direction.

Numerical study on the impact of ground heating and ambient wind speed on flow fields in street canyons

NASA Astrophysics Data System (ADS)

Li, Lei; Yang, Lin; Zhang, Li-Jie; Jiang, Yin

2012-11-01

The impact of ground heating on flow fields in street canyons under different ambient wind speed conditions was studied based on numerical methods. A series of numerical tests were performed, and three factors including height-to-width (H/W) ratio, ambient wind speed and ground heating intensity were taken into account. Three types of street canyon with H/W ratios of 0.5, 1.0 and 2.0, respectively, were used in the simulation and seven speed values ranging from 0.0 to 3.0 m s-1 were set for the ambient wind speed. The ground heating intensity, which was defined as the difference between the ground temperature and air temperature, ranged from 10 to 40 K with an increase of 10 K in the tests. The results showed that under calm conditions, ground heating could induce circulation with a wind speed of around 1.0 m s-1, which is enough to disperse pollutants in a street canyon. It was also found that an ambient wind speed threshold may exist for street canyons with a fixed H/W ratio. When ambient wind speed was lower than the threshold identified in this study, the impact of the thermal effect on the flow field was obvious, and there existed a multi-vortex flow pattern in the street canyon. When the ambient wind speed was higher than the threshold, the circulation pattern was basically determined by dynamic effects. The tests on the impact of heating intensity showed that a higher ground heating intensity could strengthen the vortical flow within the street canyon, which would help improve pollutant diffusion capability in street canyons.

Strain-specific functional and numerical responses are required to evaluate impacts on predator-prey dynamics.

PubMed

Yang, Zhou; Lowe, Chris D; Crowther, Will; Fenton, Andy; Watts, Phillip C; Montagnes, David J S

2013-02-01

We use strains recently collected from the field to establish cultures; then, through laboratory studies we investigate how among strain variation in protozoan ingestion and growth rates influences population dynamics and intraspecific competition. We focused on the impact of changing temperature because of its well-established effects on protozoan rates and its ecological relevance, from daily fluctuations to climate change. We show, first, that there is considerable inter-strain variability in thermal sensitivity of maximum growth rate, revealing distinct differences among multiple strains of our model species Oxyrrhis marina. We then intensively examined two representative strains that exhibit distinctly different thermal responses and parameterised the influence of temperature on their functional and numerical responses. Finally, we assessed how these responses alter predator-prey population dynamics. We do this first considering a standard approach, which assumes that functional and numerical responses are directly coupled, and then compare these results with a novel framework that incorporates both functional and numerical responses in a fully parameterised model. We conclude that: (i) including functional diversity of protozoa at the sub-species level will alter model predictions and (ii) including directly measured, independent functional and numerical responses in a model can provide a more realistic account of predator-prey dynamics.

The experimental and numerical investigation of pistol bullet penetrating soft tissue simulant.

PubMed

Wang, Yongjuan; Shi, Xiaoning; Chen, Aijun; Xu, Cheng

2015-04-01

Gelatin, a representative simulant for soft tissue of the human body, was used to study the effects of 9 mm pistol bullet's penetration. The behavior of a bullet penetrating gelatin was quantified by the temporary cavity sizes in ballistic gelatin and the pressure values of bullet's impact. A numerical simulation model of a bullet penetrating the soft tissue simulant gelatin was built using the finite element method (FEM). The model was validated by the comparison between the numerical results and the experimental results. During a bullet penetrating ballistic gelatin, four stages were clearly observed in both the experiment and the numerical simulation: a smooth attenuation stage, a rolling stage, a full penetration stage, and a stage of expansion and contraction. The cavity evolution, equivalent stress field and the strain field in gelatin were analyzed by numerical simulation. Moreover, the effects of the bullet's impact velocities and angles of incidence on the temporary cavity in gelatin, its velocity attenuation, and its rolling angle were investigated, as well as the bullet's resistance and energy variation. The physical process and the interactive mechanism during a pistol bullet penetrating gelatin were comprehensively revealed. This may be significant for research in wound ballistics. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Numerical investigation of road salt impact on an urban wellfield.

PubMed

Bester, M L; Frind, E O; Molson, J W; Rudolph, D L

2006-01-01

The impact of road salt on a wellfield in a complex glacial moraine aquifer system is studied by numerical simulation. The moraine underlies an extensive urban and industrial landscape, which draws its water supply from >20 wellfields, several of which are approaching or have exceeded the drinking water limit for chloride. The study investigates the mechanisms of road salt infiltration, storage, and transport in the subsurface and assesses the effectiveness of mitigation measures designed to reduce the impact. The three-dimensional transport model accounts for increases in salt loading, as well as growth of the urbanized area and road network over the past 50 years. The simulations, which focus on one impacted wellfield, show chloride plumes originating mainly at arterial roads and migrating through aquitard windows into the water supply aquifers. The results suggest that the aquifer system contains a large and heterogeneously distributed mass of chloride and that concentrations in the aquifer can be substantially higher than the concentrations in the well water. Future impact scenarios indicate that although the system responds rapidly to reductions in salt loading, the residual chloride mass may take decades to flush out, even if road salting were discontinued. The implications with respect to urban wellfields in typical snow-belt areas are discussed.

American War Narratives: An Analytic Study and Linkage to National Will

DTIC Science & Technology

2016-05-26

War, the United States has engaged in numerous conflicts where national will has been tested and has had an impact on the conduct of military...capture the war narrative. As a result, when war is not officially declared, the omission of a formal declaration can impact on the war narrative... impact on the British and Hessian forces as evidenced by subsequent emigration patterns following the conclusion of the war. The Hessians were so

The Impact of Well-Field Configuration and Permeability Heterogeneity on Contaminant Mass Removal and Plume Persistence

NASA Astrophysics Data System (ADS)

Guo, Z.; Brusseau, M. L.

2015-12-01

The purpose of this study is to investigate the effects of well-field hydraulics and permeability heterogeneity on mass-removal efficiency for systems comprising large groundwater contaminant plumes. A three-dimensional (3D) numerical model was used to simulate the impact of different well-field configurations on pump-and-treat mass removal for heterogeneous domains. The relationship between reduction in contaminant mass discharge (CMDR) and mass removal (MR) was used as the metric to examine remediation efficiency. The impacts of well-field configuration on mass removal behavior is attributed to mass-transfer constraints associated with regions of low flow, which can be muted by the influence of permeability heterogeneity. These impacts are reflected in the associated CMDR-MR profiles. Systems whose CDMR-MR profiles are below the 1:1 relationship line are associated with more efficient well-field configurations. The impact of domain heterogeneity on mass-removal effectiveness was investigated in terms of both variance and correlation scale of the random permeability distributions and indexed by the CMDR-MR relationship. Data collected from pump-and-treat operations conducted in a section of the Tucson International Airport Area (TIAA) federal Superfund site were used as a case study. The comparison between simulated and measured site data supports the general validity of the numerical model, and results from the case study are consistent with the conclusions of the theoretical study. These results illustrate that the CMDR-MR relationship can be an effective way to quantify the impacts of different factors on mass-removal efficiency.

Impacts of the horizontal and vertical grids on the numerical solutions of the dynamical equations – Part 2: Quasi-geostrophic Rossby modes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Konor, Celal S.; Randall, David A.

We use a normal-mode analysis to investigate the impacts of the horizontal and vertical discretizations on the numerical solutions of the quasi-geostrophic anelastic baroclinic and barotropic Rossby modes on a midlatitude β plane. The dispersion equations are derived for the linearized anelastic system, discretized on the Z, C, D, CD, (DC), A, E and B horizontal grids, and on the L and CP vertical grids. The effects of various horizontal grid spacings and vertical wavenumbers are discussed. A companion paper, Part 1, discusses the impacts of the discretization on the inertia–gravity modes on a midlatitude f plane.The results of our normal-modemore » analyses for the Rossby waves overall support the conclusions of the previous studies obtained with the shallow-water equations. We identify an area of disagreement with the E-grid solution.« less

A VAS-numerical model impact study using the Gal-Chen variational approach. [Visible Infrared Spin-Scan Radiometer Atmospheric Sounder (VAS)

NASA Technical Reports Server (NTRS)

Aune, Robert M.; Uccellini, Louis W.; Peterson, Ralph A.; Tuccillo, James J.

1987-01-01

Numerical experiments to assess the impact of incorporating temperature data from the VISSR Atmospheric Sounder (VAS) using the assimilation technique developed by Gal-Chen (1986) modified for use in the Mesoscale Atmospheric Simulation System (MASS) model were conducted. The scheme is designed to utilize the high temporal and horizontal resolution of satellite retrievals while maintaining the fine vertical structure generated by the model. This is accomplished by adjusting the model lapse rates to reflect thicknesses retrieved from VAS and applying a three-dimensional variational that preserves the distribution of the geopotential fields in the model. A nudging technique whereby the model temperature fields are gradually adjusted toward the updated temperature fields during model integration is also tested. An adiabatic version of MASS is used in all experiments to better isolate mass-momentum imbalances. The method has a sustained impact over an 18 hr model simulation.

Impacts of the horizontal and vertical grids on the numerical solutions of the dynamical equations – Part 2: Quasi-geostrophic Rossby modes

DOE PAGES

Konor, Celal S.; Randall, David A.

2018-05-08

We use a normal-mode analysis to investigate the impacts of the horizontal and vertical discretizations on the numerical solutions of the quasi-geostrophic anelastic baroclinic and barotropic Rossby modes on a midlatitude β plane. The dispersion equations are derived for the linearized anelastic system, discretized on the Z, C, D, CD, (DC), A, E and B horizontal grids, and on the L and CP vertical grids. The effects of various horizontal grid spacings and vertical wavenumbers are discussed. A companion paper, Part 1, discusses the impacts of the discretization on the inertia–gravity modes on a midlatitude f plane.The results of our normal-modemore » analyses for the Rossby waves overall support the conclusions of the previous studies obtained with the shallow-water equations. We identify an area of disagreement with the E-grid solution.« less

Impacts of the horizontal and vertical grids on the numerical solutions of the dynamical equations - Part 2: Quasi-geostrophic Rossby modes

NASA Astrophysics Data System (ADS)

Konor, Celal S.; Randall, David A.

2018-05-01

We use a normal-mode analysis to investigate the impacts of the horizontal and vertical discretizations on the numerical solutions of the quasi-geostrophic anelastic baroclinic and barotropic Rossby modes on a midlatitude β plane. The dispersion equations are derived for the linearized anelastic system, discretized on the Z, C, D, CD, (DC), A, E and B horizontal grids, and on the L and CP vertical grids. The effects of various horizontal grid spacings and vertical wavenumbers are discussed. A companion paper, Part 1, discusses the impacts of the discretization on the inertia-gravity modes on a midlatitude f plane.The results of our normal-mode analyses for the Rossby waves overall support the conclusions of the previous studies obtained with the shallow-water equations. We identify an area of disagreement with the E-grid solution.

Impact of atmospheric forcing on heat content variability in the sub-surface layer in the Japan/East Sea, 1948-2009

NASA Astrophysics Data System (ADS)

Stepanov, Dmitry; Gusev, Anatoly; Diansky, Nikolay

2016-04-01

Based on numerical simulations the study investigates impact of atmospheric forcing on heat content variability of the sub-surface layer in Japan/East Sea (JES), 1948-2009. We developed a model configuration based on a INMOM model and atmospheric forcing extracted from the CORE phase II experiment dataset 1948-2009, which enables to assess impact of only atmospheric forcing on heat content variability of the sub-surface layer of the JES. An analysis of kinetic energy (KE) and total heat content (THC) in the JES obtained from our numerical simulations showed that the simulated circulation of the JES is being quasi-steady state. It was found that the year-mean KE variations obtained from our numerical simulations are similar those extracted from the SODA reanalysis. Comparison of the simulated THC and that extracted from the SODA reanalysis showed significant consistence between them. An analysis of numerical simulations showed that the simulated circulation structure is very similar that obtained from the PALACE floats in the intermediate and abyssal layers in the JES. Using empirical orthogonal function analysis we studied spatial-temporal variability of the heat content of the sub-surface layer in the JES. Based on comparison of the simulated heat content variations with those obtained from natural observations an assessment of the atmospheric forcing impact on the heat content variability was obtained. Using singular value decomposition analysis we considered relationships between the heat content variability and wind stress curl as well as sensible heat flux in winter. It was established the major role of sensible heat flux in decadal variability of the heat content of the sub-surface layer in the JES. The research was supported by the Russian Foundation for Basic Research (grant N 14-05-00255) and the Council on the Russian Federation President Grants (grant N MK-3241.2015.5)

Experimental Modeling of a Formula Student Carbon Composite Nose Cone

PubMed Central

Fellows, Neil A.

2017-01-01

A numerical impact study is presented on a Formula Student (FS) racing car carbon composite nose cone. The effect of material model and model parameter selection on the numerical deceleration curves is discussed in light of the experimental deceleration data. The models show reasonable correlation in terms of the shape of the deceleration-displacement curves but do not match the peak deceleration values with errors greater that 30%. PMID:28772982

Numerical studies of temperature effect on the extrusion fracture and swell of plastic micro-pipe

NASA Astrophysics Data System (ADS)

Ren, Zhong; Huang, Xingyuan; Xiong, Zhihua

2018-03-01

Temperature is a key factor that impacts extrusion forming quality of plastic micro-pipe. In this study, the effect of temperature on extrusion fracture and swell of plastic micro-pipe was investigated by numerical method. Under a certain of the melt’s flow volume, the extrusion pattern, extrusion swelling ratio of melt are obtained under different temperatures. Results show that the extrusion swelling ratio of plastic micro-pipe decreases with increasing of temperature. In order to study the reason of temperature effect, the physical distributions of plastic micro-pipe are gotten. Numerical results show that the viscosity, pressure, stress value of melt are all decreased with the increasing of temperature, which leads to decrease the extrusion swell and fracture phenomenon for the plastic micro-pipe.

A CFD study of gas-solid jet in a CFB riser flow

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Tingwen; Guenther, Chris

2012-03-01

Three-dimensional high-resolution numerical simulations of a gas–solid jet in a high-density riser flow were conducted. The impact of gas–solid injection on the riser flow hydrodynamics was investigated with respect to voidage, tracer mass fractions, and solids velocity distribution. The behaviors of a gas–solid jet in the riser crossflow were studied through the unsteady numerical simulations. Substantial separation of the jetting gas and solids in the riser crossflow was observed. Mixing of the injected gas and solids with the riser flow was investigated and backmixing of gas and solids was evaluated. In the current numerical study, both the overall hydrodynamics ofmore » riser flow and the characteristics of gas–solid jet were reasonably predicted compared with the experimental measurements made at NETL.« less

Impact analysis of air gap motion with respect to parameters of mooring system for floating platform

NASA Astrophysics Data System (ADS)

Shen, Zhong-xiang; Huo, Fa-li; Nie, Yan; Liu, Yin-dong

2017-04-01

In this paper, the impact analysis of air gap concerning the parameters of mooring system for the semi-submersible platform is conducted. It is challenging to simulate the wave, current and wind loads of a platform based on a model test simultaneously. Furthermore, the dynamic equivalence between the truncated and full-depth mooring system is still a tuff work. However, the wind and current loads can be tested accurately in wind tunnel model. Furthermore, the wave can be simulated accurately in wave tank test. The full-scale mooring system and the all environment loads can be simulated accurately by using the numerical model based on the model tests simultaneously. In this paper, the air gap response of a floating platform is calculated based on the results of tunnel test and wave tank. Meanwhile, full-scale mooring system, the wind, wave and current load can be considered simultaneously. In addition, a numerical model of the platform is tuned and validated by ANSYS AQWA according to the model test results. With the support of the tuned numerical model, seventeen simulation cases about the presented platform are considered to study the wave, wind, and current loads simultaneously. Then, the impact analysis studies of air gap motion regarding the length, elasticity, and type of the mooring line are performed in the time domain under the beam wave, head wave, and oblique wave conditions.

Impact of Image Noise on Gamma Index Calculation

NASA Astrophysics Data System (ADS)

Chen, M.; Mo, X.; Parnell, D.; Olivera, G.; Galmarini, D.; Lu, W.

2014-03-01

Purpose: The Gamma Index defines an asymmetric metric between the evaluated image and the reference image. It provides a quantitative comparison that can be used to indicate sample-wised pass/fail on the agreement of the two images. The Gamma passing/failing rate has become an important clinical evaluation tool. However, the presence of noise in the evaluated and/or reference images may change the Gamma Index, hence the passing/failing rate, and further, clinical decisions. In this work, we systematically studied the impact of the image noise on the Gamma Index calculation. Methods: We used both analytic formulation and numerical calculations in our study. The numerical calculations included simulations and clinical images. Three different noise scenarios were studied in simulations: noise in reference images only, in evaluated images only, and in both. Both white and spatially correlated noises of various magnitudes were simulated. For clinical images of various noise levels, the Gamma Index of measurement against calculation, calculation against measurement, and measurement against measurement, were evaluated. Results: Numerical calculations for both the simulation and clinical data agreed with the analytic formulations, and the clinical data agreed with the simulations. For the Gamma Index of measurement against calculation, its distribution has an increased mean and an increased standard deviation as the noise increases. On the contrary, for the Gamma index of calculation against measurement, its distribution has a decreased mean and stabilized standard deviation as the noise increases. White noise has greater impact on the Gamma Index than spatially correlated noise. Conclusions: The noise has significant impact on the Gamma Index calculation and the impact is asymmetric. The Gamma Index should be reported along with the noise levels in both reference and evaluated images. Reporting of the Gamma Index with switched roles of the images as reference and evaluated images or some composite metrics would be a good practice.

G-Jitter Effects in Protein Crystal Growth - A Numerical Study

NASA Technical Reports Server (NTRS)

Ramachandran, N.; Baugher, C. R.

1995-01-01

The impact of spacecraft acceleration environment on Protein Crystal Growth (PCG) is studied. A brief overview of the Space Shuttle acceleration environment is provided followed by a simple scaling procedure used to obtain estimates of the flow and concentration field characteristics in PCG. A detailed two-dimensional numerical model is then used to simulate the PCG system response to different disturbance scenarios; viz. residual g effects, impulse type disturbances and oscillatory inputs. The results show that PCG is susceptible to g-jitter and is a good candidate for vibration isolation.

Numerical modelling of closed-cell aluminium foam under dynamic loading

NASA Astrophysics Data System (ADS)

Hazell, Paul; Kader, M. A.; Islam, M. A.; Escobedo, J. P.; Saadatfar, M.

2015-06-01

Closed-cell aluminium foams are extensively used in aerospace and automobile industries. The understanding of their behaviour under impact loading conditions is extremely important since impact problems are directly related to design of these engineering structures. This research investigates the response of a closed-cell aluminium foam (CYMAT) subjected to dynamic loading using the finite element software ABAQUS/explicit. The aim of this research is to numerically investigate the material and structural properties of closed-cell aluminium foam under impact loading conditions with interest in shock propagation and its effects on cell wall deformation. A μ-CT based 3D foam geometry is developed to simulate the local cell collapse behaviours. A number of numerical techniques are applied for modelling the crush behaviour of aluminium foam to obtain the more accurate results. The simulation results are compared with experimental data. Comparison of the results shows a good correlation between the experimental results and numerical predictions.

Approximate Micromechanics Treatise of Composite Impact

NASA Technical Reports Server (NTRS)

Chamis, Christos C.; Handler, Louis M.

2005-01-01

A formalism is described for micromechanic impact of composites. The formalism consists of numerous equations which describe all aspects of impact from impactor and composite conditions to impact contact, damage progression, and penetration or containment. The formalism is based on through-the-thickness displacement increments simulation which makes it convenient to track local damage in terms of microfailure modes and their respective characteristics. A flow chart is provided to cast the formalism (numerous equations) into a computer code for embedment in composite mechanic codes and/or finite element composite structural analysis.

Bridging the condensation-collision size gap: a direct numerical simulation of continuous droplet growth in turbulent clouds

NASA Astrophysics Data System (ADS)

Chen, Sisi; Yau, Man-Kong; Bartello, Peter; Xue, Lulin

2018-05-01

In most previous direct numerical simulation (DNS) studies on droplet growth in turbulence, condensational growth and collisional growth were treated separately. Studies in recent decades have postulated that small-scale turbulence may accelerate droplet collisions when droplets are still small when condensational growth is effective. This implies that both processes should be considered simultaneously to unveil the full history of droplet growth and rain formation. This paper introduces the first direct numerical simulation approach to explicitly study the continuous droplet growth by condensation and collisions inside an adiabatic ascending cloud parcel. Results from the condensation-only, collision-only, and condensation-collision experiments are compared to examine the contribution to the broadening of droplet size distribution (DSD) by the individual process and by the combined processes. Simulations of different turbulent intensities are conducted to investigate the impact of turbulence on each process and on the condensation-induced collisions. The results show that the condensational process promotes the collisions in a turbulent environment and reduces the collisions when in still air, indicating a positive impact of condensation on turbulent collisions. This work suggests the necessity of including both processes simultaneously when studying droplet-turbulence interaction to quantify the turbulence effect on the evolution of cloud droplet spectrum and rain formation.

Numerical Studies on a Rotor with Distributed Suction for Noise Reduction

NASA Astrophysics Data System (ADS)

Lutz, Thorsten; Arnold, Benjamin; Wolf, Alexander; Krämer, Ewald

2014-06-01

Minimizing the flow-induced noise is an important issue in the design of modern onshore wind turbines. There is a number of proven passive means to reduce the aeroacoustic noise, such as the implementation of serrations, porous trailing edges or the aeroacoustic airfoil design. The noise emission can be further reduced by active flow control techniques. In the present study the impact of distributed boundary layer suction on the noise emission of an airfoil and a complete rotor is investigated. Aerodynamic and aeroacoustic wind tunnel tests were performed for the NACA 64-418 airfoil and supplemented by numerical calculations. The aeroacoustic analyses have been conducted by means of the institute's Rnoise prediction scheme. The 2D studies have shown that noise reductions of 5 dB can be achieved by suction at moderate mass flow rates. To study the impact of three-dimensional effects numerical investigations have been conducted on the example of the generic NREL 5MW rotor with suction applied in the outer part of the blade. The predictions for the complete rotor provided smaller benefits compared to those for the isolated airfoil, mainly because the examined suction configurations were not optimized with respect to the extent of the suction patch and suction distribution.

A two-stage approach for estimating a statewide truck trip table.

DOT National Transportation Integrated Search

2014-05-01

Statewide models, including passenger and freight movements, are frequently used for : supporting numerous statewide planning activities. Many states use them for traffic impact : studies, air quality conformity analysis, freight planning, economic d...

Numerical simulation and experimental validation of Lamb wave propagation behavior in composite plates

NASA Astrophysics Data System (ADS)

Kim, Sungwon; Uprety, Bibhisha; Mathews, V. John; Adams, Daniel O.

2015-03-01

Structural Health Monitoring (SHM) based on Acoustic Emission (AE) is dependent on both the sensors to detect an impact event as well as an algorithm to determine the impact location. The propagation of Lamb waves produced by an impact event in thin composite structures is affected by several unique aspects including material anisotropy, ply orientations, and geometric discontinuities within the structure. The development of accurate numerical models of Lamb wave propagation has important benefits towards the development of AE-based SHM systems for impact location estimation. Currently, many impact location algorithms utilize the time of arrival or velocities of Lamb waves. Therefore the numerical prediction of characteristic wave velocities is of great interest. Additionally, the propagation of the initial symmetric (S0) and asymmetric (A0) wave modes is important, as these wave modes are used for time of arrival estimation. In this investigation, finite element analyses were performed to investigate aspects of Lamb wave propagation in composite plates with active signal excitation. A comparative evaluation of two three-dimensional modeling approaches was performed, with emphasis placed on the propagation and velocity of both the S0 and A0 wave modes. Results from numerical simulations are compared to experimental results obtained from active AE testing. Of particular interest is the directional dependence of Lamb waves in quasi-isotropic carbon/epoxy composite plates. Numerical and experimental results suggest that although a quasi-isotropic composite plate may have the same effective elastic modulus in all in-plane directions, the Lamb wave velocity may have some directional dependence. Further numerical analyses were performed to investigate Lamb wave propagation associated with circular cutouts in composite plates.

NOy and O3 in the Asian Monsoon Anticyclone: Uncertainties associated with the Convection and Lightning in a Global Model

NASA Astrophysics Data System (ADS)

Pozzer, A.; Ojha, N.; Tost, H.; Joeckel, P.; Fischer, H.; Ziereis, H.; Zahn, A.; Tomsche, L.; Lelieveld, J.

2017-12-01

The impacts of Asian monsoon on the tropospheric chemistry are difficult to simulate in numerical models due to the lack of accurate emission inventories over the Asian region and the strong influence of parameterized processes such as convection and lightning. Further, the lack of observational data over the region during the monsoon period reduce drastically the capability to evaluate numerical models. Here, we combine simulations using the global EMAC (ECHAM5/MESSy2 Atmospheric Chemistry) model with the observational dataset based on the OMO campaign (July-August 2015) to study the tropospheric composition in the Asian monsoon anticyclone. The results of the simulations capture the C-shape of the CO vertical profiles, typically observed during the summer monsoon. The observed spatio-temporal variations in O3, CO, and NOy are reproduced by EMAC, with a better correlation in the upper troposphere (UT). However, the model overestimates NOy and O3 mixing ratios in the anticyclone by 25% and 35%, respectively. A series of numerical experiments showed the strong lightning emissions in the model as the source of this overestimation, with the anthropogenic NOx sources (in Asia) and global soil emissions having lower impact in the UT. A reduction of the lightning NOx emission by 50% leads to a better agreement between the model and OMO observations of NOy and O3. The uncertainties in the lightning emissions are found to considerably influence the OH distribution in the UT over India and downwind. The study reveals existing uncertainties in the estimations of monsoon impact on the tropospheric composition, and highlights the need to constrain numerical simulations with state-of-the-art observations for deriving the budget of trace species of climatic relevance.

Impact of the 4 April 2014 Saharan dust outbreak on the photovoltaic power generation in Germany

NASA Astrophysics Data System (ADS)

Rieger, Daniel; Steiner, Andrea; Bachmann, Vanessa; Gasch, Philipp; Förstner, Jochen; Deetz, Konrad; Vogel, Bernhard; Vogel, Heike

2017-11-01

The importance for reliable forecasts of incoming solar radiation is growing rapidly, especially for those countries with an increasing share in photovoltaic (PV) power production. The reliability of solar radiation forecasts depends mainly on the representation of clouds and aerosol particles absorbing and scattering radiation. Especially under extreme aerosol conditions, numerical weather prediction has a systematic bias in the solar radiation forecast. This is caused by the design of numerical weather prediction models, which typically account for the direct impact of aerosol particles on radiation using climatological mean values and the impact on cloud formation assuming spatially and temporally homogeneous aerosol concentrations. These model deficiencies in turn can lead to significant economic losses under extreme aerosol conditions. For Germany, Saharan dust outbreaks occurring 5 to 15 times per year for several days each are prominent examples for conditions, under which numerical weather prediction struggles to forecast solar radiation adequately. We investigate the impact of mineral dust on the PV-power generation during a Saharan dust outbreak over Germany on 4 April 2014 using ICON-ART, which is the current German numerical weather prediction model extended by modules accounting for trace substances and related feedback processes. We find an overall improvement of the PV-power forecast for 65 % of the pyranometer stations in Germany. Of the nine stations with very high differences between forecast and measurement, eight stations show an improvement. Furthermore, we quantify the direct radiative effects and indirect radiative effects of mineral dust. For our study, direct effects account for 64 %, indirect effects for 20 % and synergistic interaction effects for 16 % of the differences between the forecast including mineral dust radiative effects and the forecast neglecting mineral dust.

A second-order impact model for forest fire regimes.

PubMed

Maggi, Stefano; Rinaldi, Sergio

2006-09-01

We present a very simple "impact" model for the description of forest fires and show that it can mimic the known characteristics of wild fire regimes in savannas, boreal forests, and Mediterranean forests. Moreover, the distribution of burned biomasses in model generated fires resemble those of burned areas in numerous large forests around the world. The model has also the merits of being the first second-order model for forest fires and the first example of the use of impact models in the study of ecosystems.

Numerical impact simulation of gradually increased kinetic energy transfer has the potential to break up folded protein structures resulting in cytotoxic brain tissue edema.

PubMed

von Holst, Hans; Li, Xiaogai

2013-07-01

Although the consequences of traumatic brain injury (TBI) and its treatment have been improved, there is still a substantial lack of understanding the mechanisms. Numerical simulation of the impact can throw further lights on site and mechanism of action. A finite element model of the human head and brain tissue was used to simulate TBI. The consequences of gradually increased kinetic energy transfer was analyzed by evaluating the impact intracranial pressure (ICP), strain level, and their potential influences on binding forces in folded protein structures. The gradually increased kinetic energy was found to have the potential to break apart bonds of Van der Waals in all impacts and hydrogen bonds at simulated impacts from 6 m/s and higher, thereby superseding the energy in folded protein structures. Further, impacts below 6 m/s showed none or very slight increase in impact ICP and strain levels, whereas impacts of 6 m/s or higher showed a gradual increase of the impact ICP and strain levels reaching over 1000 KPa and over 30%, respectively. The present simulation study shows that the free kinetic energy transfer, impact ICP, and strain levels all have the potential to initiate cytotoxic brain tissue edema by unfolding protein structures. The definition of mild, moderate, and severe TBI should thus be looked upon as the same condition and separated only by a gradual severity of impact.

Effect of seabed roughness on tidal current turbines

NASA Astrophysics Data System (ADS)

Gupta, Vikrant; Wan, Minping

2017-11-01

Tidal current turbines are shown to have potential to generate clean energy for a negligible environmental impact. These devices, however, operate in high to moderate current regions where the flow is highly turbulent. It has been shown in flume tank experiments at IFREMER in Boulogne-Sur-Mer (France) and NAFL in the University of Minnesota (US) that the level of turbulence and boundary layer profile affect a turbine's power output and wake characteristics. A major factor that determines these marine flow characteristics is the seabed roughness. Experiments, however, cannot simulate the high Reynolds number conditions of real marine flows. For that, we rely on numerical simulations. High accuracy numerical methods, such as DNS, of wall-bounded flows are very expensive, where the number of grid-points needed to resolve the flow varies as (Re) 9 / 4 (where Re is the flow Reynolds number). While numerically affordable RANS methods compromise on accuracy. Wall-modelled LES methods, which provide both accuracy and affordability, have been improved tremendously in the recent years. We discuss the application of such numerical methods for studying the effect of seabed roughness on marine flow features and their impact on turbine power output and wake characteristics. NSFC, Project Number 11672123.

Extension and Validation of a Hybrid Particle-Finite Element Method for Hypervelocity Impact Simulation. Chapter 2

NASA Technical Reports Server (NTRS)

Fahrenthold, Eric P.; Shivarama, Ravishankar

2004-01-01

The hybrid particle-finite element method of Fahrenthold and Horban, developed for the simulation of hypervelocity impact problems, has been extended to include new formulations of the particle-element kinematics, additional constitutive models, and an improved numerical implementation. The extended formulation has been validated in three dimensional simulations of published impact experiments. The test cases demonstrate good agreement with experiment, good parallel speedup, and numerical convergence of the simulation results.

Asteroid and comet impacts on Mars and their influence on atmospheric mass evolution and habitability.

NASA Astrophysics Data System (ADS)

Karatekin, Özgür

2015-04-01

Impacts by asteroids and comets could have significant affects on the habitability and atmospheric evolution of terrestrial planets by removing part of its atmosphere, by delivering into it material and volatiles. Large impacts could have repeatedly destroyed the existing biosphere, but in the mean time new subsurface habitats have likely formed from impact induced hydrothermal systems. Early in its history, Mars could have a much denser atmosphere and higher surface temperatures to sustain the presence of stable liquid water or saline solution at the surface, as suggested by several studies. The environmental effects of a period of impact bombardment on terrestrial planets remain poorly constrained. In this study we revisit the atmospheric loss and delivery of volatiles on Mars between the end of the Noachian and present using numerical models. Following an impact, the quantity of escaped atmosphere, as well as impactor and target materials can be estimated using numerical simulations. Studies on the atmospheric loss and delivery due to impacts differ sometimes by orders of magnitude, mainly due to different equation of state and dynamical models used. The hydrocode simulations designed to simulate a single impact are not suitable to study the cumulative effect of impact erosion and delivery in the long term due to their extremely high computation costs. Instead, empirical approximations based on hydrocode simulations have been used to estimate atmospheric evolution. Comparison between different hydrocode results and atmospheric mass evolution upon impacts based on empirical models will be presented using revised model parameters. In addition, different delivery and lost mechanisms including volcanic outgassing and non-thermal escape, can be taken into account to study various atmospheric evolution scenarios. Our results suggest that impacts alone can hardly remove a significant amount of atmospheric mass over this period. Contribution of additional factors such as outgassing and non- thermal escape processes can not explain neither the presence of surface pressure larger than few hundreds of mbars 3.9 Gyr ago. Based on extreme case scenarios, maximum surface pressures at the end of the Noachian, could be as much as 0.25 bar or 1.9 bar, with and without CO2 storage into carbonate reservoirs, respectively.

An approach for quantifying geomorphological impacts for EIA of transportation infrastructures: a case study in northern Spain

NASA Astrophysics Data System (ADS)

Bonachea, Jaime; Bruschi, Viola Maria; Remondo, Juan; González-Díez, Alberto; Salas, Luis; Bertens, Jurjen; Cendrero, Antonio; Otero, César; Giusti, Cecilia; Fabbri, Andrea; González-Lastra, José Ramón; Aramburu, José María

2005-03-01

A methodological proposal for the assessment of impacts due to linear infrastructures such as motorways, railways, etc. is presented. The approach proposed includes a series of specific issues to be addressed for each geomorphological feature analysed—both 'static' and 'dynamic'—as well as a series of steps to be followed in the process. Geomorphic characteristics potentially affected were initially identified on the basis of a conceptual activities/impacts model that helps to single out geomorphic impacts related to environmental concerns for the area. The following issues were addressed for each individual impact: nature of potential effects; indicators that can be used to measure impacts; criteria of 'geomorphologic performance'; procedure for measurement/prediction of changes; translation of geomorphologic impacts into significant terms from the viewpoint of human concerns; possible mitigation and/or compensation measures. The procedure has been applied to a case study corresponding to a new motorway in the Basque Country, northern Spain. Geomorphological impacts considered in this analysis included: (1) consumable resources; (2) sites of geomorphological interest; (3) land units with high potential for use, high productivity or value for conservation; (4) visual landscape; (5) slope instability processes. The procedure has been designed for implementation in a Geographic Information System (GIS) environment. Details are given on the application of the method to each individual impact analysed and results are presented in both numerical and map form. Impacts assessed were initially expressed by means of heterogeneous magnitudes, depending on the geomorphological feature considered. Those geomorphological impacts were then translated into significant terms and homogeneous magnitudes. Integration was carried out on the basis of impact values thus obtained. Final integrated results were also expressed in numerical and map form. The method proposed enables comparison of alternatives as well as 'prediction' and assessment of impacts in terms directly related to geomorphic characteristics. It also facilitates the expression of those impacts in terms that allow integration with other types of environmental impacts.

Exploring Variation in the Impact of Dual-Credit Coursework on Postsecondary Outcomes: A Quasi-Experimental Analysis of Texas Students

ERIC Educational Resources Information Center

Giani, Matthew; Alexander, Celeste; Reyes, Pedro

2014-01-01

Despite the growing popularity of dual-credit courses as a college readiness strategy, numerous reviews of the literature have noted a number of important limitations of the research on the effects of dual-credit on student postsecondary outcomes. This study addressed these gaps in the literature by estimating the impact of dual-credit courses on…

Hydra, a model system for environmental studies.

PubMed

Quinn, Brian; Gagné, François; Blaise, Christian

2012-01-01

Hydra have been extensively used for studying the teratogenic and toxic potential of numerous toxins throughout the years and are more recently growing in popularity to assess the impacts of environmental pollutants. Hydra are an appropriate bioindicator species for use in environmental assessment owing to their easily measurable physical (morphology), biochemical (xenobiotic biotransformation; oxidative stress), behavioural (feeding) and reproductive (sexual and asexual) endpoints. Hydra also possess an unparalleled ability to regenerate, allowing the assessment of teratogenic compounds and the impact of contaminants on stem cells. Importantly, Hydra are ubiquitous throughout freshwater environments and relatively easy to culture making them appropriate for use in small scale bioassay systems. Hydra have been used to assess the environmental impacts of numerous environmental pollutants including metals, organic toxicants (including pharmaceuticals and endocrine disrupting compounds), nanomaterials and industrial and municipal effluents. They have been found to be among the most sensitive animals tested for metals and certain effluents, comparing favourably with more standardised toxicity tests. Despite their lack of use in formalised monitoring programmes, Hydra have been extensively used and are regarded as a model organism in aquatic toxicology.

Numerical simulation of liquid jet impact on a rigid wall

NASA Astrophysics Data System (ADS)

Aganin, A. A.; Guseva, T. S.

2016-11-01

Basic points of a numerical technique for computing high-speed liquid jet impact on a rigid wall are presented. In the technique the flows of the liquid and the surrounding gas are governed by the equations of gas dynamics in the density, velocity, and pressure, which are integrated by the CIP-CUP method on dynamically adaptive grids without explicitly tracking the gas-liquid interface. The efficiency of the technique is demonstrated by the results of computing the problems of impact of the liquid cone and the liquid wedge on a wall in the mode with the shockwave touching the wall by its edge. Numerical solutions of these problems are compared with the analytical solution of the problem of impact of the plane liquid flow on a wall. Applicability of the technique to the problems of the high-speed liquid jet impact on a wall is illustrated by the results of computing a problem of impact of a cylindrical liquid jet with the hemispherical end on a wall covered by a layer of the same liquid.

Study of hypervelocity meteoroid impact on orbital space stations

NASA Technical Reports Server (NTRS)

Leimbach, K. R.; Prozan, R. J.

1973-01-01

Structural damage resulting in hypervelocity impact of a meteorite on a spacecraft is discussed. Of particular interest is the backside spallation caused by such a collision. To treat this phenomenon two numerical schemes were developed in the course of this study to compute the elastic-plastic flow fracture of a solid. The numerical schemes are a five-point finite difference scheme and a four-node finite element scheme. The four-node finite element scheme proved to be less sensitive to the type of boundary conditions and loadings. Although further development work is needed to improve the program versatility (generalization of the network topology, secondary storage for large systems, improving of the coding to reduce the run time, etc.), the basic framework is provided for a utilitarian computer program which may be used in a wide variety of situations. Analytic results showing the program output are given for several test cases.

Deconvolution of acoustic emissions for source localization using time reverse modeling

NASA Astrophysics Data System (ADS)

Kocur, Georg Karl

2017-01-01

Impact experiments on small-scale slabs made of concrete and aluminum were carried out. Wave motion radiated from the epicenter of the impact was recorded as voltage signals by resonant piezoelectric transducers. Numerical simulations of the elastic wave propagation are performed to simulate the physical experiments. The Hertz theory of contact is applied to estimate the force impulse, which is subsequently used for the numerical simulation. Displacements at the transducer positions are calculated numerically. A deconvolution function is obtained by comparing the physical (voltage signal) and the numerical (calculated displacement) experiments. Acoustic emission signals due to pencil-lead breaks are recorded, deconvolved and applied for localization using time reverse modeling.

Energy absorption ability of buckyball C720 at low impact speed: a numerical study based on molecular dynamics

PubMed Central

2013-01-01

The dynamic impact response of giant buckyball C720 is investigated by using molecular dynamics simulations. The non-recoverable deformation of C720 makes it an ideal candidate for high-performance energy absorption. Firstly, mechanical behaviors under dynamic impact and low-speed crushing are simulated and modeled, which clarifies the buckling-related energy absorption mechanism. One-dimensional C720 arrays (both vertical and horizontal alignments) are studied at various impact speeds, which show that the energy absorption ability is dominated by the impact energy per buckyball and less sensitive to the number and arrangement direction of buckyballs. Three-dimensional stacking of buckyballs in simple cubic, body-centered cubic, hexagonal, and face-centered cubic forms are investigated. Stacking form with higher occupation density yields higher energy absorption. The present study may shed lights on employing C720 assembly as an advanced energy absorption system against low-speed impacts. PMID:23360618

Numerical Coupling and Simulation of Point-Mass System with the Turbulent Fluid Flow

NASA Astrophysics Data System (ADS)

Gao, Zheng

A computational framework that combines the Eulerian description of the turbulence field with a Lagrangian point-mass ensemble is proposed in this dissertation. Depending on the Reynolds number, the turbulence field is simulated using Direct Numerical Simulation (DNS) or eddy viscosity model. In the meanwhile, the particle system, such as spring-mass system and cloud droplets, are modeled using the ordinary differential system, which is stiff and hence poses a challenge to the stability of the entire system. This computational framework is applied to the numerical study of parachute deceleration and cloud microphysics. These two distinct problems can be uniformly modeled with Partial Differential Equations (PDEs) and Ordinary Differential Equations (ODEs), and numerically solved in the same framework. For the parachute simulation, a novel porosity model is proposed to simulate the porous effects of the parachute canopy. This model is easy to implement with the projection method and is able to reproduce Darcy's law observed in the experiment. Moreover, the impacts of using different versions of k-epsilon turbulence model in the parachute simulation have been investigated and conclude that the standard and Re-Normalisation Group (RNG) model may overestimate the turbulence effects when Reynolds number is small while the Realizable model has a consistent performance with both large and small Reynolds number. For another application, cloud microphysics, the cloud entrainment-mixing problem is studied in the same numerical framework. Three sets of DNS are carried out with both decaying and forced turbulence. The numerical result suggests a new way parameterize the cloud mixing degree using the dynamical measures. The numerical experiments also verify the negative relationship between the droplets number concentration and the vorticity field. The results imply that the gravity has fewer impacts on the forced turbulence than the decaying turbulence. In summary, the proposed framework can be used to solve a physics problem that involves turbulence field and point-mass system, and therefore has a broad application.

Experimental and Numerical Investigation of Fiber Reinforced Laminated Composites Subject to Low-Velocity Impact

NASA Astrophysics Data System (ADS)

Thorsson, Solver I.

Foreign object impact on composite materials continues to be an active field due to its importance in the design of load bearing composite aerostructures. The problem has been studied by many through the decades. Extensive experimental studies have been performed to characterize the impact damage and failure mechanisms. Leaders in aerospace industry are pushing for reliable, robust and efficient computational methods for predicting impact response of composite structures. Experimental and numerical investigations on the impact response of fiber reinforced polymer matrix composite (FRPC) laminates are presented. A detailed face-on and edge-on impact experimental study is presented. A novel method for conducting coupon-level edge-on impact experiments is introduced. The research is focused on impact energy levels that are in the vicinity of the barely visible impact damage (BVID) limit of the material system. A detailed post-impact damage study is presented where non-destructive inspection (NDI) methods such as ultrasound scanning and computed tomography (CT) are used. Detailed fractography studies are presented for further investigation of the through-the-thickness damage due to the impact event. Following the impact study, specimens are subjected to compression after impact (CAI) to establish the effect of BVID on the compressive strength after impact (CSAI). A modified combined loading compression (CLC) test method is proposed for compression testing following an edge-on impact. Experimental work on the rate sensitivity of the mode I and mode II inter-laminar fracture toughness is also investigated. An improved wedge-insert fracture (WIF) method for conducting mode I inter-laminar fracture at elevated loading rates is introduced. Based on the experimental results, a computational modeling approach for capturing face-on impact and CAI is developed. The model is then extended to edge-on impact and CAI. Enhanced Schapery Theory (EST) is utilized for modeling the full field damage and failure present in a unidirectional (UD) lamina within a laminate. Schapery Theory (ST) is a thermodynamically based work potential material model which captures the pre-peak softening due to matrix micro-cracking such as hackling, micro fissures, etc. The Crack Band (CB) method is utilized to capture macroscopic matrix and fiber failure modes such as ply splitting and fiber rupture. Discrete Cohesive Zone Method (DCZM) elements are implemented for capturing inter-laminar delaminations, using discrete nodal traction-separation governed interactions. The model is verified against the impact experimental results and the associated CAI procedures. The model results are in good agreement with experimental findings. The model proved capable of predicting the representative experimental failure modes.

An advanced three-phase physical, experimental and numerical method for tsunami induced boulder transport

NASA Astrophysics Data System (ADS)

Oetjen, Jan; Engel, Max; Prasad Pudasaini, Shiva; Schüttrumpf, Holger; Brückner, Helmut

2017-04-01

Coasts around the world are affected by high-energy wave events like storm surges or tsunamis depending on their regional climatological and geological settings. By focusing on tsunami impacts, we combine the abilities and experiences of different scientific fields aiming at improved insights of near- and onshore tsunami hydrodynamics. We investigate the transport of coarse clasts - so called boulders - due to tsunami impacts by a multi-methodology approach of numerical modelling, laboratory experiments, and sedimentary field records. Coupled numerical hydrodynamic and boulder transport models (BTM) are widely applied for analysing the impact characteristics of the transport by tsunami, such as wave height and flow velocity. Numerical models able to simulate past tsunami events and the corresponding boulder transport patterns with high accuracy and acceptable computational effort can be utilized as powerful forecasting models predicting the impact of a coast approaching tsunami. We have conducted small-scale physical experiments in the tilting flume with real shaped boulder models. Utilizing the structure from motion technique (Westoby et al., 2012) we reconstructed real boulders from a field study on the Island of Bonaire (Lesser Antilles, Caribbean Sea, Engel & May, 2012). The obtained three-dimensional boulder meshes are utilized for creating downscaled replica of the real boulder for physical experiments. The results of the irregular shaped boulder are compared to experiments with regular shaped boulder models to achieve a better insight about the shape related influence on transport patterns. The numerical model is based on the general two-phase mass flow model by Pudasaini (2012) enhanced for boulder transport simulations. The boulder is implemented using the immersed boundary technique (Peskin, 2002) and the direct forcing approach. In this method Cartesian grids (fluid and particle phase) and Lagrangian meshes (boulder) are combined. By applying the immersed boundary method we can compute the interactions between fluid, particles and arbitrary boulder shape. We are able to reproduce the exact physical experiment for calibration and verification of the tsunami boulder transport phenomena. First results of the study will be presented. Engel, M.; May, S.M.: Bonaire's boulder fields revisited: evidence for Holocene tsunami impact on the Leeward, Antilles. Quaternary Science Reviews 54, 126-141, 2012. Peskin, C.S.: The immersed boundary method. Acta Numerica, 479 - 517, 2002. Pudasaini, S. P.: A general two-phase debris flow model. J. Geophys. Res. Earth Surf., 117, F03010, 2012. Westoby, M.J.; Brasington, J.; Glasser, N.F.; Hambrey, M.J.; Reynolds, J.M.: 'Structure-from-Motion' photogrammetry - a low-cost, effective tool for geoscience applications. Geomorphology 179, 300-314, 2012.

The NASA JSC Hypervelocity Impact Test Facility (HIT-F)

NASA Technical Reports Server (NTRS)

Crews, Jeanne L.; Christiansen, Eric L.

1992-01-01

The NASA Johnson Space Center Hypervelocity Impact Test Facility was created in 1980 to study the hypervelocity impact characteristics of composite materials. The facility consists of the Hypervelocity Impact Laboratory (HIRL) and the Hypervelocity Analysis Laboratory (HAL). The HIRL supports three different-size light-gas gun ranges which provide the capability of launching particle sizes from 100 micron spheres to 12.7 mm cylinders. The HAL performs three functions: (1) the analysis of data collected from shots in the HIRL, (2) numerical and analytical modeling to predict impact response beyond test conditions, and (3) risk and damage assessments for spacecraft exposed to the meteoroid and orbital debris environments.

Numerical Model Studies of the Martian Mesoscale Circulations

NASA Technical Reports Server (NTRS)

Segal, Moti; Arritt, Raymond W.

1997-01-01

The study objectives were to evaluate by numerical modeling various possible mesoscale circulation on Mars and related atmospheric boundary layer processes. The study was in collaboration with J. Tillman of the University of Washington (who supported the study observationally). Interaction has been made with J. Prusa of Iowa State University in numerical modeling investigation of dynamical effects of topographically-influenced flow. Modeling simulations included evaluations of surface physical characteristics on: (i) the Martian atmospheric boundary layer and (ii) their impact on thermally and dynamically forced mesoscale flows. Special model evaluations were made in support of selection of the Pathfinder landing sites. J. Tillman's finding of VL-2 inter-annual temperature difference was followed by model simulations attempting to point out the forcing for this feature. Publication of the results in the reviewed literature in pending upon completion of the manuscripts in preparation as indicated later.

Impact of projectiles of different geometries on dry granular media using DEM simulations

NASA Astrophysics Data System (ADS)

Vajrala, Spandana; Bagheri, Hosain; Emady, Heather; Marvi, Hamid; Particulate Process; Product Design Group Team; Birth Lab Collaboration

Recently, several studies involving numerical and experimental methods have focused on the study of impact dynamics in both dry and wet granular media. Most of these studies considered the impact of spherical projectiles under different conditions, while representative models could involve more complex shapes. Examples include such things as an animal's foot impacting sand or an asteroid hitting the ground. Dropping different shaped geometries with conserved density, volume and velocity on a granular bed may experience contrasting drag forces upon penetration. This is the result of the difference in the surface areas coming in contact with the granular media. Therefore, this work will utilize three-dimensional Discrete Element Modelling (DEM) simulations to observe and compare the impact of different geometries like cylinder and cuboid of same material properties and volume. These geometries will be impacted on a loosely packed non-cohesive dry granular bed with the same impact velocities where the effect of surface area in contact with the granular media will be analyzed upon impact and penetration.

Numerical Study of High-Speed Droplet Impact on Surfaces and its Physical Cleaning Effects

NASA Astrophysics Data System (ADS)

Kondo, Tomoki; Ando, Keita

2015-11-01

Spurred by the demand for cleaning techniques of low environmental impact, one favors physical cleaning that does not rely on any chemicals. One of the promising candidates is based on water jets that often involve fission into droplet fragments and collide with target surfaces to which contaminant particles (often micron-sized or even smaller) stick. Hydrodynamic force (e.g., shearing and lifting) arising from the droplet impact will play a role to remove the particles, but its detailed mechanism is still unknown. To explore the role of high-speed droplet impact in physical cleaning, we solve compressible Navier-Stokes equations with a finite volume method that is designed to capture both shocks and material interfaces in accurate and robust manners. Water hammer and shear flow accompanied by high-speed droplet impact at a rigid wall is simulated to evaluate lifting force and rotating torque, which are relevant to the application of particle removal. For the simulation, we use the numerical code recently developed by Computational Flow Group lead by Tim Colonius at Caltech. The first author thanks Jomela Meng for her help in handling the code during his stay at Caltech.

Assessment of "Teenage Diaries" for Teaching Concepts in Adolescent Psychology

ERIC Educational Resources Information Center

McKee, Meredith L.; MacDonald, Pamelyn M.

2009-01-01

Student self-report measures have been reported in numerous studies to assert that the use of case studies in college psychology courses can help students to better understand the relevance of course topics; however, few studies have directly measured the impact of case studies on students' learning. The present study differs from previous studies…

Numerical modeling of experimental observations on gas formation and multi-phase flow of carbon dioxide in subsurface formations

NASA Astrophysics Data System (ADS)

Pawar, R.; Dash, Z.; Sakaki, T.; Plampin, M. R.; Lassen, R. N.; Illangasekare, T. H.; Zyvoloski, G.

2011-12-01

One of the concerns related to geologic CO2 sequestration is potential leakage of CO2 and its subsequent migration to shallow groundwater resources leading to geochemical impacts. Developing approaches to monitor CO2 migration in shallow aquifer and mitigate leakage impacts will require improving our understanding of gas phase formation and multi-phase flow subsequent to CO2 leakage in shallow aquifers. We are utilizing an integrated approach combining laboratory experiments and numerical simulations to characterize the multi-phase flow of CO2 in shallow aquifers. The laboratory experiments involve a series of highly controlled experiments in which CO2 dissolved water is injected in homogeneous and heterogeneous soil columns and tanks. The experimental results are used to study the effects of soil properties, temperature, pressure gradients and heterogeneities on gas formation and migration. We utilize the Finite Element Heat and Mass (FEHM) simulator (Zyvoloski et al, 2010) to numerically model the experimental results. The numerical models capture the physics of CO2 exsolution, multi-phase fluid flow as well as sand heterogeneity. Experimental observations of pressure, temperature and gas saturations are used to develop and constrain conceptual models for CO2 gas-phase formation and multi-phase CO2 flow in porous media. This talk will provide details of development of conceptual models based on experimental observation, development of numerical models for laboratory experiments and modelling results.

Energetic analysis of drop's maximum spreading on solid surface with low impact speed

NASA Astrophysics Data System (ADS)

Huang, Hai-Meng; Chen, Xiao-Peng

2018-02-01

Drops impacting on a flat solid surface will spread until it reaches maximum contact with the substrate underneath. After that, it recoils. In the present work, the variations of energy components during the spreading are studied carefully, including kinetic, capillary, and dissipated energies. Our experimental and numerical results show that, when the impact speed is low, the fast slipping of the contact line (in inertia-capillary regime) and corresponding "interface relaxation" lead to extra dissipation. An auxiliary dissipation is therefore introduced into the traditional theoretical model. The energy components predicted by the improved model agree with the experimental and numerical results very well. As the impact speed increases (the Weber number, W e =ρ D0V02/γ , becomes larger than 40 in the present work), the dissipation induced by the initial velocity plays more important roles. The analyses also indicate that on the hydrophobic surfaces the auxiliary dissipation is lower than that on hydrophilic ones. In the later circumstances, the contact angle is larger and the spreading is weaker.

Diode Laser Clinical Efficacy and Mini-Invasivity in Surgical Exposure of Impacted Teeth.

PubMed

Migliario, Mario; Rizzi, Manuela; Lucchina, Alberta Greco; Renò, Filippo

2016-11-01

The gold standard to arrange impacted teeth in the dental arch is represented by a surgical approach followed by orthodontic traction force application. In the literature, many surgical approaches are proposed to reach such a scope. The aim of the present study is to demonstrate how laser technique could positively assist surgical approaches.Study population was composed by 16 patients undergoing orthodontic treatment of 20 impacted teeth. In 10 patients (population A) surgical exposure of the impacted teeth was performed using a 980 nm diode laser, while in the other 10 patients (population B), surgical incision was performed using a traditional lancet.Only 3 patients of the population A needed local anesthesia for surgical procedure while the remaining 7 patients reported only faint pain during surgery. Two patients referred postsurgical pain (numerical rating scale average value = 2) and needed to take analgesics. None of the patients showed other postsurgical side effects (bleeding, edema).All population B patients needed infiltrative anesthesia and referred postsurgical pain (numerical rating scale average value >4) treated with analgesics. Moreover, in such population, 4 patients referred lips edema while 4 showed bleeding and 6 needed surgical sutures of soft tissues.The lack of side effects of laser surgical approach to expose impacted teeth must persuade dental practitioners to choose such a clinical approach to closed surgical approach every time it is possible.

Effect of Mesoscale and Multiscale Modeling on the Performance of Kevlar Woven Fabric Subjected to Ballistic Impact: A Numerical Study

NASA Astrophysics Data System (ADS)

Jia, Xin; Huang, Zhengxiang; Zu, Xudong; Gu, Xiaohui; Xiao, Qiangqiang

2013-12-01

In this study, an optimal finite element model of Kevlar woven fabric that is more computational efficient compared with existing models was developed to simulate ballistic impact onto fabric. Kevlar woven fabric was modeled to yarn level architecture by using the hybrid elements analysis (HEA), which uses solid elements in modeling the yarns at the impact region and uses shell elements in modeling the yarns away from the impact region. Three HEA configurations were constructed, in which the solid element region was set as about one, two, and three times that of the projectile's diameter with impact velocities of 30 m/s (non-perforation case) and 200 m/s (perforation case) to determine the optimal ratio between the solid element region and the shell element region. To further reduce computational time and to maintain the necessary accuracy, three multiscale models were presented also. These multiscale models combine the local region with the yarn level architecture by using the HEA approach and the global region with homogenous level architecture. The effect of the varying ratios of the local and global area on the ballistic performance of fabric was discussed. The deformation and damage mechanisms of fabric were analyzed and compared among numerical models. Simulation results indicate that the multiscale model based on HEA accurately reproduces the baseline results and obviously decreases computational time.

On gel electrophoresis of dielectric charged particles with hydrophobic surface: A combined theoretical and numerical study.

PubMed

Majee, Partha Sarathi; Bhattacharyya, Somnath; Gopmandal, Partha Pratim; Ohshima, Hiroyuki

2018-03-01

A theoretical study on the gel electrophoresis of a charged particle incorporating the effects of dielectric polarization and surface hydrophobicity at the particle-liquid interface is made. A simplified model based on the weak applied field and low charge density assumption is also presented and compared with the full numerical model for a nonpolarizable particle to elucidate the nonlinear effects such as double layer polarization and relaxation as well as surface conduction. The main motivation of this study is to analyze the electrophoresis of the surface functionalized nanoparticle with tunable hydrophobicity or charged fluid drop in gel medium by considering the electrokinetic effects and hydrodynamic interactions between the particle and the gel medium. An effective medium approach, in which the transport in the electrolyte-saturated hydrogel medium is governed by the Brinkman equation, is adopted in the present analysis. The governing electrokinetic equations based on the conservation principles are solved numerically. The Navier-slip boundary condition along with the continuity condition of dielectric displacement are imposed on the surface of the hydrophobic polarizable particle. The impact of the slip length on the electrophoresis is profound for a thinner Debye layer, however, surface conduction effect also becomes significant for a hydrophobic particle. Impact of hydrophobicity and relaxation effects are higher for a larger particle. Dielectric polarization creates a reduction in its electrophoretic propulsion and has negligible impact at the thinner Debye length as well as lower gel screening length. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hypervelocity impacts on asteroids and momentum transfer I. Numerical simulations using porous targets

NASA Astrophysics Data System (ADS)

Jutzi, Martin; Michel, Patrick

2014-02-01

In this paper, we investigate numerically the momentum transferred by impacts of small (artificial) projectiles on asteroids. The study of the momentum transfer efficiency as a function of impact conditions and of the internal structure of an asteroid is crucial for performance assessment of the kinetic impactor concept of deflecting an asteroid from its trajectory. The momentum transfer is characterized by the so-called momentum multiplication factor β, which has been introduced to define the momentum imparted to an asteroid in terms of the momentum of the impactor. Here we present results of code calculations of the β factor for porous targets, in which porosity takes the form of microporosity and/or macroporosity. The results of our study using a large range of impact conditions indicate that the momentum multiplication factor β is small for porous targets even for very high impact velocities (β<2 for vimp⩽15 km/s), which is consistent with published scaling laws and results of laboratory experiments (Holsapple, K.A., Housen, K.R. [2012]. Icarus 221, 875-887; Holsapple, K.A., Housen, K.R. [2013]. Proceedings of the IAA Planetary Defense Conference 2013, Flagstaff, USA). It is found that both porosity and strength can have a large effect on the amount of transferred momentum and on the scaling of β with impact velocity. On the other hand, the macroporous inhomogeneities considered here do not have a significant effect on β.

Thirty years of change in forest soils of the Allegheny Plateau, Pennsylvania

Treesearch

S.W. Bailey; S.B. Horsley; R.P. Long

2005-01-01

Numerous studies have investigated the potential depletion of available base cation pools from forest soils in regions impacted by acid deposition. However, these studies mostly used indirect methods. Retrospective studies, providing direct evidence of chemical changes in forest soils, are relatively rare due to a lack of appropriate sampling, documentation, and...

Low velocity impact of 6082-T6 aluminum plates

NASA Astrophysics Data System (ADS)

Mocian, Oana Alexandra; Constantinescu, Dan Mihai; Sandu, Marin; Sorohan, Ştefan

2018-02-01

The low velocity domain covers vehicle impacts, ship collisions and even accidentally tool drops. Even though more and more research is needed into these fields, most of the papers concerning impact problems focus on impact at medium and high velocities. Understanding the behavior of structures subjected to low velocity impact is of major importance when referring to impact resistance and damage tolerance. The paper presents an experimental and numerical investigation on the low velocity behavior of 6082-T6 aluminum plates. Impact tests were performed using an Instron Ceast 9340 drop-weight testing machine. In the experimental procedure, square plates were mounted on a circular support, fixed with a pneumatic clamping system and impacted with a hemispherical steel projectile. Specimens were impacted at constant weight and different impact velocities. The effect of different impact energies was investigated. The impact event was then simulated using the nonlinear finite element code LS_DYNA in order to determine the effect of strain rate upon the mechanical behavior of the aluminum plates. Moreover, in order to capture the exact behavior of the material, a special attention has been given to the selection of the correct material model and its parameters, which, in large extent, depend on the observed behavior of the aluminum plate during the test and the actual response of the plate under simulation. The numerical predictions are compared with the experimental observations and the applicability of the numerical model for further researches is analyzed.

Screening ecological impacts of environmental surface waters using cell-based metabolomics

EPA Science Inventory

Anthropogenic chemicals are routinely detected in aquatic ecosystems downstream from wastewater treatment plants (WWTPs), industrial and agricultural operations, and numerous other sources. Various studies have shown that exposure to such complex chemical mixtures can produce adv...

Numerical simulation of film-cooled ablative rocket nozzles

NASA Technical Reports Server (NTRS)

Landrum, D. B.; Beard, R. M.

1996-01-01

The objective of this research effort was to evaluate the impact of incorporating an additional cooling port downstream between the injector and nozzle throat in the NASA Fast Track chamber. A numerical model of the chamber was developed for the analysis. The analysis did not model ablation but instead correlated the initial ablation rate with the initial nozzle wall temperature distribution. The results of this study provide guidance in the development of a potentially lighter, second generation ablative rocket nozzle which maintains desired performance levels.

How Parents Read Counting Books and Non-numerical Books to Their Preverbal Infants: An Observational Study.

PubMed

Goldstein, Alison; Cole, Thomas; Cordes, Sara

2016-01-01

Studies have stressed the importance of counting with children to promote formal numeracy abilities; however, little work has investigated when parents begin to engage in this behavior with their young children. In the current study, we investigated whether parents elaborated on numerical information when reading a counting book to their preverbal infants and whether developmental differences in numerical input exist even in the 1st year of life. Parents and their 5-10 months old infants were asked to read, as they would at home, two books to their infants: a counting book and another book that did not have numerical content. Parents' spontaneous statements rarely focused on number and those that did consisted primarily of counting, with little emphasis on labeling the cardinality of the set. However, developmental differences were observed even in this age range, such that parents were more likely to make numerical utterances when reading to older infants. Together, results are the first to characterize naturalistic reading behaviors between parents and their preverbal infants in the context of counting books, suggesting that although counting books promote numerical language in parents, infants still receive very little in the way of numerical input before the end of the 1st year of life. While little is known regarding the impact of number talk on the cognitive development of young infants, the current results may guide future work in this area by providing the first assessment of the characteristics of parental numerical input to preverbal infants.

Clinical Impact of Time-of-Flight and Point Response Modeling in PET Reconstructions: A Lesion Detection Study

PubMed Central

Schaefferkoetter, Joshua; Casey, Michael; Townsend, David; Fakhri, Georges El

2013-01-01

Time-of-flight (TOF) and point spread function (PSF) modeling have been shown to improve PET reconstructions, but the impact on physicians in the clinical setting has not been thoroughly investigated. A lesion detection and localization study was performed using simulated lesions in real patient images. Four reconstruction schemes were considered: ordinary Poisson OSEM (OP) alone and combined with TOF, PSF, and TOF+PSF. The images were presented to physicians experienced in reading PET images, and the performance of each was quantified using localization receiver operating characteristic (LROC). Numerical observers (non-prewhitening and Hotelling) were used to identify optimal reconstruction parameters, and observer SNR was compared to the performance of the physicians. The numerical models showed good agreement with human performance, and best performance was achieved by both when using TOF+PSF. These findings suggest a large potential benefit of TOF+PSF for oncology PET studies, especially in the detection of small, low-intensity, focal disease in larger patients. PMID:23403399

Clinical impact of time-of-flight and point response modeling in PET reconstructions: a lesion detection study

NASA Astrophysics Data System (ADS)

Schaefferkoetter, Joshua; Casey, Michael; Townsend, David; El Fakhri, Georges

2013-03-01

Time-of-flight (TOF) and point spread function (PSF) modeling have been shown to improve PET reconstructions, but the impact on physicians in the clinical setting has not been thoroughly investigated. A lesion detection and localization study was performed using simulated lesions in real patient images. Four reconstruction schemes were considered: ordinary Poisson OSEM (OP) alone and combined with TOF, PSF, and TOF + PSF. The images were presented to physicians experienced in reading PET images, and the performance of each was quantified using localization receiver operating characteristic. Numerical observers (non-prewhitening and Hotelling) were used to identify optimal reconstruction parameters, and observer SNR was compared to the performance of the physicians. The numerical models showed good agreement with human performance, and best performance was achieved by both when using TOF + PSF. These findings suggest a large potential benefit of TOF + PSF for oncology PET studies, especially in the detection of small, low-intensity, focal disease in larger patients.

Factors Affecting Self-Esteem and Self-Efficacy in the Unemployed

ERIC Educational Resources Information Center

Maddy, Luther M., III

2013-01-01

Unemployment is, and will likely continue to be, a problem in industrialized nations. Numerous studies have concluded unemployment negatively impacts self-esteem and self-efficacy. Additional studies have shown that unemployed individuals with lower self-esteem and self-efficacy tend to remain unemployed longer than individuals with higher…

Numerical tool for tsunami risk assessment in the southern coast of Dominican Republic

NASA Astrophysics Data System (ADS)

Macias Sanchez, J.; Llorente Isidro, M.; Ortega, S.; Gonzalez Vida, J. M., Sr.; Castro, M. J.

2016-12-01

The southern coast of Dominican Republic is a very populated region, with several important cities including Santo Domingo, its capital. Important activities are rooted in the southern coast including tourism, industry, commercial ports, and, energy facilities, among others. According to historical reports, it has been impacted by big earthquakes accompanied by tsunamis as in Azua in 1751 and recently Pedernales in 2010, but their sources are not clearly identified. The aim of the present work is to develop a numerical tool to simulate the impact in the southern coast of the Dominican Republic of tsunamis generated in the Caribbean Sea. This tool, based on the Tsunami-HySEA model from EDANYA group (University of Malaga, Spain), could be used in the framework of a Tsunami Early Warning Systems due the very short computing times when only propagation is computed or it could be used to assess inundation impact, computing inundation with a initial 5 meter resolution. Numerical results corresponding to three theoretical sources are used to test the numerical tool.

Numerical analysis of projectile impact in woven texile structures

NASA Technical Reports Server (NTRS)

Roylance, D.

1977-01-01

Computer codes were developed for simulating the dynamic fracture and viscoelastic constitutive response due to stress wave interaction and reflections caused by ballistic impact on woven textiles. The method, which was developed for use in the design and analysis of protection devices for personnel armor, has potential for use in studies of rotor blade burst containment at high velocity. Alterations in coding required for burst containment problems are discussed.

Longleaf pine regeneration following Hurricane Ivan utilizing the RLGS plots

Treesearch

John C. Gilbert; John S. Kush

2013-01-01

On September 16, 2004, Hurricane Ivan hit the Alabama coast and severely impacted numerous plots in the U.S. Forest Service’s Regional Longleaf Growth Study (RLGS). The Escambia Experimental Forest (EEF) has 201 of the 325 RLGS plots. Nearly one-third of the EEF was impacted. Nine plots with pole-sized trees were entirely lost. Another 54 plots had some type of damage...

Numerical Analysis of Ice Impacts on Azimuth Propeller

DTIC Science & Technology

2013-09-01

or nozzle . The shape of the ducting as well as the propeller type determines the effect or characteristic the ship requires for thrust . The two...NAVAL POSTGRADUATE SCHOOL MONTEREY, CALIFORNIA THESIS Approved for public release; distribution is unlimited NUMERICAL ANALYSIS...OF ICE IMPACTS ON AZIMUTH PROPELLER by Gary G. Kim September 2013 Thesis Co-Advisors: Young W. Kwon Jarema M. Didoszak THIS PAGE

Volcanic Loading: The Dust Veil Index (1985) (NDP-013)

DOE Data Explorer

Lamb, H. H. [University of East Anglia, Norwich, United Kingdom; Boden, Thomas A. [CDIAC, Oak Ridge National Laboratory; Watts, Julia A. [Oak Ridge National Laboratory

1985-09-01

Lamb's Dust Veil Index (DVI) is a numerical index that quantifies the impact of a particular volcanic eruption's release of dust and aerosols over the years following the event, especially the impact on the Earth's energy balance. DVIs have been calculated for eruptions occurring from 1500 through 1983. The methods used to calculate the DVI have been intercalibrated to give a DVI of 1000 for the eruption of Krakatoa in 1883. The DVI for any volcanic eruption is based on a review of the observational, empirical, and theoretical studies of the possible impact on climate of volcanic dust veils. The DVI allows one to compare volcanic eruptions by a single numerical index. The data base includes the name of the erupting volcano, year of eruption, volcano latitude and longitude, maximum extent of the dust veil, veil duration, DVI for the entire globe, DVI for the Northern Hemisphere, and DVI for the Southern Hemisphere. The data are in one file (22.6 kB).

Impact of the Test Device on the Behavior of the Acoustic Emission Signals: Contribution of the Numerical Modeling to Signal Processing

NASA Astrophysics Data System (ADS)

Issiaka Traore, Oumar; Cristini, Paul; Favretto-Cristini, Nathalie; Pantera, Laurent; Viguier-Pla, Sylvie

2018-01-01

In a context of nuclear safety experiment monitoring with the non destructive testing method of acoustic emission, we study the impact of the test device on the interpretation of the recorded physical signals by using spectral finite element modeling. The numerical results are validated by comparison with real acoustic emission data obtained from previous experiments. The results show that several parameters can have significant impacts on acoustic wave propagation and then on the interpretation of the physical signals. The potential position of the source mechanism, the positions of the receivers and the nature of the coolant fluid have to be taken into account in the definition a pre-processing strategy of the real acoustic emission signals. In order to show the relevance of such an approach, we use the results to propose an optimization of the positions of the acoustic emission sensors in order to reduce the estimation bias of the time-delay and then improve the localization of the source mechanisms.

Ballistic Impact Response of Kevlar 49 and Zylon under Conditions Representing Jet Engine Fan Containment

NASA Technical Reports Server (NTRS)

Pereira, J. Michael; Revilock, Duane M.

2007-01-01

A ballistic impact test program was conducted to provide validation data for the development of numerical models of blade out events in fabric containment systems. The impact response of two different fiber materials - Kevlar 49 (E.I. DuPont Nemours and Company) and Zylon AS (Toyobo Co., Ltd.) was studied by firing metal projectiles into dry woven fabric specimens using a gas gun. The shape, mass, orientation and velocity of the projectile were varied and recorded. In most cases the tests were designed such that the projectile would perforate the specimen, allowing measurement of the energy absorbed by the fabric. The results for both Zylon and Kevlar presented here represent a useful set of data for the purposes of establishing and validating numerical models for predicting the response of fabrics under conditions simulating those of a jet engine blade release situation. In addition some useful empirical observations were made regarding the effects of projectile orientation and the relative performance of the different materials.

The impact of watershed management on coastal morphology: A case study using an integrated approach and numerical modeling

NASA Astrophysics Data System (ADS)

Samaras, Achilleas G.; Koutitas, Christopher G.

2014-04-01

Coastal morphology evolves as the combined result of both natural- and human- induced factors that cover a wide range of spatial and temporal scales of effect. Areas in the vicinity of natural stream mouths are of special interest, as the direct connection with the upstream watershed extends the search for drivers of morphological evolution from the coastal area to the inland as well. Although the impact of changes in watersheds on the coastal sediment budget is well established, references that study concurrently the two fields and the quantification of their connection are scarce. In the present work, the impact of land-use changes in a watershed on coastal erosion is studied for a selected site in North Greece. Applications are based on an integrated approach to quantify the impact of watershed management on coastal morphology through numerical modeling. The watershed model SWAT and a shoreline evolution model developed by the authors (PELNCON-M) are used, evaluating with the latter the performance of the three longshore sediment transport rate formulae included in the model formulation. Results document the impact of crop abandonment on coastal erosion (agricultural land decrease from 23.3% to 5.1% is accompanied by the retreat of ~ 35 m in the vicinity of the stream mouth) and show the effect of sediment transport formula selection on the evolution of coastal morphology. Analysis denotes the relative importance of the parameters involved in the dynamics of watershed-coast systems, and - through the detailed description of a case study - is deemed to provide useful insights for researchers and policy-makers involved in their study.

Student Success in University Education: A Multi-Measurement Study of the Impact of Student and Faculty Factors on Study Progress

ERIC Educational Resources Information Center

Van Den Berg, M. N.; Hofman, W. H. A.

2005-01-01

This study focuses on the factors that determine study progress and numerical success rate in higher education. Study progress is influenced at three levels, namely the student level, course/institute level and government level. It is expected that various groups of economic, social, psychological and organisational factors will together influence…

Mechanical characterization and modelling of the temperature-dependent impact behaviour of a biocompatible poly(L-lactide)/poly(ε-caprolactone) polymer blend.

PubMed

Gustafsson, Gustaf; Nishida, Masahiro; Ito, Yoshitaka; Häggblad, Hans-Åke; Jonsén, Pär; Takayama, Tetsuo; Todo, Mitsugu

2015-11-01

Poly(ε-caprolactone) (PCL) is a ductile, bioabsorbable polymer that has been employed as a blend partner for poly(L-lactic acid) (PLLA). An improvement of the material strength and impact resistance of PLLA/PCL polymer blends compared to pure PLLA has been shown previously. To use numerical simulations in the design process of new components composed of the PLLA/PCL blend, a constitutive model for the material has to be established. In this work, a constitutive model for a PLLA/PCL polymer blend is established from the results of compressive tests at high and low strain rates at three different temperatures, including the body temperature. Finite element simulations of the split Hopkinson pressure bar test using the established constitutive model are carried out under the same condition as the experiments. During the experiments, the changes in the diameter and thickness of the specimens are captured by a high-speed video camera. The accuracy of the numerical model is tested by comparing the simulation results, such as the stress, strain, thickness and diameter histories of the specimens, with those measured in the experiments. The numerical model is also validated against an impact test of non-homogenous strains and strain rates. The results of this study provide a validated numerical model for a PLLA/PCL polymer blend at strain rates of up to 1800 s(-1) in the temperature range between 22°C and 50°C. Copyright © 2015 Elsevier Ltd. All rights reserved.

Regional scale impact of tidal forcing on groundwater flow in unconfined coastal aquifers

NASA Astrophysics Data System (ADS)

Pauw, P. S.; Oude Essink, G. H. P.; Leijnse, A.; Vandenbohede, A.; Groen, J.; van der Zee, S. E. A. T. M.

2014-09-01

This paper considers the impact of tidal forcing on regional groundwater flow in an unconfined coastal aquifer. Numerical models are used to quantify this impact for a wide range of hydrogeological conditions. Both a shallow and a deep aquifer are investigated with regard to three dimensionless parameter groups that determine the groundwater flow to a large extent. Analytical expressions are presented that allow for a quick estimate of the regional scale effect of tidal forcing under the same conditions as used in the numerical models. Quantitatively, the results in this paper are complementary to previous studies by taking into account variable density groundwater flow, dispersive salt transport and a seepage face in the intertidal area. Qualitatively, the results are in line with previous investigations. The time-averaged hydraulic head at the high tide mark increases upon a decrease of each of the three considered dimensionless parameter groups: R (including the ratio of the hydraulic conductivity and the precipitation excess), α (the slope of the intertidal area) and AL (the ratio of the width of the fresh water lens and the tidal amplitude). The relative change of the location and the hydraulic head of the groundwater divide, which together characterize regional groundwater flow, increase as α and AL decrease, but decrease as R decreases. The difference between the analytical solutions and numerical results is small. Therefore, the presented analytical solutions can be used to estimate the bias that is introduced in a numerical model if tidal forcing is neglected. The results should be used with caution in case of significant wave forcing, as this was not considered.

[Numeric alterations in the dys gene and their association with clinical features].

PubMed

Mampel, Alejandra; Echeverría, María Inés; Vargas, Ana Lía; Roque, María

2011-01-01

The Duchenne/Becker muscular dystrophy is a hereditary miopathy with a recessive sex-linked pattern. The related gene is called DYS and the coded protein plays a crucial role in the anchorage between the cytoskeleton and the cellular membrane in muscle cells. Different clinical manifestations are observed depending on the impact of the genetic alteration on the protein. The global register of mutations reveals an enhanced frequency for deletions/duplications of one or more exons affecting the DYS gene. In the present work, numeric alterations have been studied in the 79 exons of the DYS gene. The study has been performed on 59 individuals, including 31 independent cases and 28 cases with a familial link. The applied methodology was Multiplex Ligation Dependent Probe Amplification (MLPA). In the 31 independent cases clinical data were established: i.e. the clinical score, the Raven test percentiles, and the creatininphosphokinase (CPK) blood values. Our results reveal a 61.3% frequency of numeric alterations affecting the DYS gene in our population, provoking all of them a reading frame shift. The rate for de novo mutations was identified as 35.2%. Alterations involving a specific region of one exon were observed with high frequency, affecting a specific region. A significant association was found between numeric alterations and a low percentile for the Raven test. These data contribute to the local knowledge of genetic alterations and their phenotypic impact for the Duchenne/Becker disease.

Patterns of linguistic and numerical performance in aphasia.

PubMed

Rath, Dajana; Domahs, Frank; Dressel, Katharina; Claros-Salinas, Dolores; Klein, Elise; Willmes, Klaus; Krinzinger, Helga

2015-02-04

Empirical research on the relationship between linguistic and numerical processing revealed inconsistent results for different levels of cognitive processing (e.g., lexical, semantic) as well as different stimulus materials (e.g., Arabic digits, number words, letters, non-number words). Information of dissociation patterns in aphasic patients was used in order to investigate the dissociability of linguistic and numerical processes. The aim of the present prospective study was a comprehensive, specific, and systematic investigation of relationships between linguistic and numerical processing, considering the impact of asemantic vs. semantic processing and the type of material employed (numbers compared to letters vs. words). A sample of aphasic patients (n = 60) was assessed with a battery of linguistic and numerical tasks directly comparable for their cognitive processing levels (e.g., perceptual, morpho-lexical, semantic). Mean performance differences and frequencies of (complementary) dissociations in individual patients revealed the most prominent numerical advantage for asemantic tasks when comparing the processing of numbers vs. letters, whereas the least numerical advantage was found for semantic tasks when comparing the processing of numbers vs. words. Different patient subgroups showing differential dissociation patterns were further analysed and discussed. A comprehensive model of linguistic and numerical processing should take these findings into account.

Lax-Wendroff and TVD finite volume methods for unidimensional thermomechanical numerical simulations of impacts on elastic-plastic solids

NASA Astrophysics Data System (ADS)

Heuzé, Thomas

2017-10-01

We present in this work two finite volume methods for the simulation of unidimensional impact problems, both for bars and plane waves, on elastic-plastic solid media within the small strain framework. First, an extension of Lax-Wendroff to elastic-plastic constitutive models with linear and nonlinear hardenings is presented. Second, a high order TVD method based on flux-difference splitting [1] and Superbee flux limiter [2] is coupled with an approximate elastic-plastic Riemann solver for nonlinear hardenings, and follows that of Fogarty [3] for linear ones. Thermomechanical coupling is accounted for through dissipation heating and thermal softening, and adiabatic conditions are assumed. This paper essentially focuses on one-dimensional problems since analytical solutions exist or can easily be developed. Accordingly, these two numerical methods are compared to analytical solutions and to the explicit finite element method on test cases involving discontinuous and continuous solutions. This allows to study in more details their respective performance during the loading, unloading and reloading stages. Particular emphasis is also paid to the accuracy of the computed plastic strains, some differences being found according to the numerical method used. Lax-Wendoff two-dimensional discretization of a one-dimensional problem is also appended at the end to demonstrate the extensibility of such numerical scheme to multidimensional problems.

Etude comparative sur la propagation de l'endommagement apres impact des composites carbone/epoxy renforces par piquage au fil Kevlar et titane-nickel

NASA Astrophysics Data System (ADS)

Vachon, Pierre-Luc

Composite laminates have strong in-plane mechanical properties, but they are generally weaker through their thickness. This specificity makes the laminates prone to delamination, particularly under low-velocity impact loads. Consequently numerous research efforts have been dedicated to developing interlaminar reinforcing methods, such as transverse stitching. The present project proposes the use of the stitching technique combined with a special stitching thread made of superelastic TiNi alloy. This technology is intended to improve the delamination toughness in composite laminates loaded in bending. In the first part of this study a numerical model was developed for analyzing composite structures. The 3-D finite element model was built with the ANSYS commercial software using 20-node solid and 8-node shell elements. The progressive damage modeling technique was used, allowing the prediction of delamination propagation in a laminate submitted to various loading modes. The model was validated for a plate under quasi-static traction load, and it was then used to simulate three-point bending tests. Secondly, carbon/epoxy composite panels were fabricated, with each panel containing unstitched and stitched specimens. Two different materials were used for the stitching thread: superelastic TiNi wires and Kevlar threads as a reference. Some stitched specimens were cut in slices in order to make some observations of the internal stitch using an optical microscope. Standardized low-velocity impact tests and compression after impact tests were carried out on stitched and unstitched specimens (ASTM D7136 and D7137). The Kevlar reinforcements have shown great performance in reducing the delaminated zone after impact, as well as in improving the residual compression strength. The TiNi reinforcements provided encouraging results during the impact tests, though being less effective than the Kevlar threads. During the compression after impact tests, only a slight difference could be measured between the TiNi-stitched and the unstitched specimens. Then the bending performance of the specimens was quantified experimentally by calculating the energy required to create a unit volume of damaged material (Gv, J/mm3). This metric is similar to the Strain Energy Release Rate (SERR) commonly used in studies on delamination. According to the experimental results, the damage resistance in three-point bending was not improved by the Kevlar reinforcements, despite the reduced damaged zone after the impact test. Indeed, when the strain energy in bending is relativized to the induced damaged volume during propagation, it turns out that the TiNi reinforcements are more effective than the Kevlar's for improving the damage resistance. Finally, the numerical study on the behavior of both types of stitched reinforcements allowed identifying subtle differences between those. Indeed, both stitching threads (TiNi and Kevlar) promoted the interlaminar propagation of the delamination during simulation of the bending test, with this behavior being less pronounced for the TiNi-stitched plate. However the Kevlar threads seemed more effective for stopping this propagation in the zones between the stitches. Keywords: composite materials, stitching, numerical model, shape memory alloy, three-point bending, low-velocity impact, ultrasound imaging.

Regional Hydroclimatic Impacts of Contemporary Amazonian Deforestation and Their Spatiotemporal Variability - An Integrated Study Using Remotely Sensed Data and Numerical Tools

NASA Astrophysics Data System (ADS)

Medvigy, D.; Khanna, J.

2016-12-01

The Amazon rainforest has been under deforestation for more than four decades. Recent investigation of the regional hydroclimatic impacts of the past three decades of deforestation has revealed a strong scale-dependence of the atmospheric response to land use change. Contemporary deforestation, affecting spatial scales of a few hundreds of kilometers, has resulted in a spatial redistribution of the local dry season rainfall, with downwind and upwind deforested regions receiving respectively 30% more and 30% less rainfall from the area mean. This phenomenon is attributable to a `dynamical' response of the boundary layer air to a reduction in surface roughness due to deforestation, apparent in both satellite and numerically simulated data. This response is starkly different from a spatially uniform increase in non-precipitating cloudiness triggered by small scale clearings, prevalent in the early phases of deforestation. This study investigates the `generalizability' of the dynamical mechanism to understand its impacts on a continually deforested Amazonia. In particular, we investigate the spatiotemporal variability of the dynamical mechanism. The nature of this investigation demands long time series and large spatial converge datasets of the hydroclimate. As such, satellite imagery of clouds (GridSat) and precipitation (PERSIANN and TRMM) has proven particularly useful in facilitating this analysis. The analysis is further complemented by a reanalysis product (ERA-interim) and numerical simulations (using a variable resolution GCM). Results indicate the presence of the dynamical mechanism during local dry and transition seasons effecting the mean precipitation during this period. Its effect on the transition season precipitation can be important for the local dry season length. The dynamical mechanism also occurs in atmospheric conditions which are otherwise less conducive to thermally triggered convection. Hence, this mechanism, which effects the seasons most important for regional ecology, emerges as a possibly impactful convective triggering mechanism. This study provides context for thinking about the climate of a future, more patchily deforested Amazonia that is more favorable to the dynamical mechanism.

Biomechanics of the Upper Extremity in Response to Dynamic Impact Loading Indicative of a Forward Fall: An Experimental and Numerical Investigation

NASA Astrophysics Data System (ADS)

Burkhart, Timothy A.

The distal radius is one of the most common fracture sites in humans, often resulting from a forward fall with more than 60 % of all fractures to the wrist requiring some form of surgical intervention. Although there is a general consensus regarding the risk factors for distal radius fractures resulting from forward falling, prevention of these injuries requires a more thorough understanding of the injury mechanisms. Therefore the overall purpose of this dissertation was to assess the response of the upper extremity to impact loading to improve the understanding of distal radius fracture mechanisms and the effectiveness of joint kinematic strategies for reducing the impact effects. Three main studies were conducted that utilized in vivo, in vitro and numerical techniques. In vitro impact testing of the distal radius revealed that fracture will occur at a mean (SD) resultant impact force and velocity of 2142.1(1228.7) N and 3.4 (0.7) m/s, respectively. Based on the failure data, multi-variate injury criteria models were produced, highlighting the dynamic and multidirectional nature of distal radius fractures The in vitro investigation was also used to develop and validate a finite element model of the distal radius. Dynamic impacts were simulated in LS-DYNARTM and the resulting z-axis force validation metrics (0.23--0.54) suggest that this is a valid model. A comparison of the experimental fracture patterns to those predicted numerically (i.e. von-Mises stress criteria) shows the finite element model is capable of accurately predicting bone failure. Finally, an in vivo fall simulation apparatus was designed and built that was found to reliably (Intraclass Correlation Coefficients > 0.6) apply multi-directional motion and upper extremity impacts indicative of forward falls. This study revealed that, to some extent, individuals are capable of selected an impact strategy that minimizes the significant injury variables that were outlined in the in vitro investigation, with very little instruction. The body of work presented here has the potential to be used to develop distal radius fracture prevention methods in an attempt to improve the health and well being of those individuals currently at the highest risk of sustaining these injuries.

The origin of the moon and the single-impact hypothesis. I

NASA Technical Reports Server (NTRS)

Benz, W.; Slattery, W. L.; Cameron, A. G. W.

1986-01-01

One of the newer ideas regarding the origin of the moon is concerned with a single-impact hypothesis. It is pointed out that this theory has the advantage of overcoming most of the difficulties with the classical theories. The angular momentum of the earth-moon system can easily be obtained by varying the initial conditions of the impact. A series of three-dimensional numerical simulations of the collision between the earth and an object of about 1/10 its mass is presented. Different impact velocities, impact parameters, and initial internal energies are considered. Attention is given to assumptions, the equation of state, numerical techniques utilizing the momentum equation and the energy conservation equation, tests, and initial conditions and units.

Observing System Forecast Experiments at the DAO

NASA Technical Reports Server (NTRS)

Atlas, Robert

2001-01-01

Since the advent of meteorological satellites in the 1960's, numerous experiments have been conducted in order to evaluate the impact of these and other data on atmospheric analysis and prediction. Such studies have included both OSE'S and OSSE's. The OSE's were conducted to evaluate the impact of specific observations or classes of observations on analyses and forecasts. Such experiments have been performed for selected types of conventional data and for various satellite data sets as they became available. (See for example the 1989 ECMWF/EUMETSAT workshop proceedings on "The use of satellite data in operational numerical weather prediction" and the references contained therein.) The ODYSSEY were conducted to evaluate the potential for future observing systems to improve Numerical Weather Prediction NWP and to plan for the Global Weather Experiment and more recently for EVANS (Atlas et al., 1985a; Arnold and Day, 1986; Hoffman et al., 1990). In addition, OSSE's have been run to evaluate trade-offs in the design of observing systems and observing networks (Atlas and Emmitt, 1991; Rohaly and Krishnamurti, 1993), and to test new methodology for data assimilation (Atlas and Bloom, 1989).

The prediction of the hydrodynamic performance of tidal current turbines

NASA Astrophysics Data System (ADS)

Y Xiao, B.; Zhou, L. J.; Xiao, Y. X.; Wang, Z. W.

2013-12-01

Nowadays tidal current energy is considered to be one of the most promising alternative green energy resources and tidal current turbines are used for power generation. Prediction of the open water performance around tidal turbines is important for the reason that it can give some advice on installation and array of tidal current turbines. This paper presents numerical computations of tidal current turbines by using a numerical model which is constructed to simulate an isolated turbine. This paper aims at studying the installation of marine current turbine of which the hydro-environmental impacts influence by means of numerical simulation. Such impacts include free-stream velocity magnitude, seabed and inflow direction of velocity. The results of the open water performance prediction show that the power output and efficiency of marine current turbine varies from different marine environments. The velocity distribution should be clearly and the suitable unit installation depth and direction be clearly chosen, which can ensure the most effective strategy for energy capture before installing the marine current turbine. The findings of this paper are expected to be beneficial in developing tidal current turbines and array in the future.

Interactions between sediment storage and bed material transport: A field and flume study

Treesearch

Bonnie J. Smith; Thomas E. Lisle; Diane G. Sutherland; Sue Hilton; Harvey M. Kelsey; Eileen M. Cashman

2002-01-01

Significant channel aggradation events have occurred in numerous coastal northern California watersheds over the past 50 years, leaving lasting impacts on stream channel morphology and habitats. Our study focuses on sediment movement and channel morphology following large aggradation events and specifically focuses on the relationship between volume of stored sediment...

Academic Libraries and High-Impact Practices for Student Retention: Library Deans' Perspectives

ERIC Educational Resources Information Center

Murray, Adam

2015-01-01

Numerous studies on retention have highlighted the role of student engagement in influencing students' withdrawal decisions. This study seeks to address how academic libraries affect student retention by examining the perception of academic library deans or directors on the alignment between library services and resources with ten nationally…

Effect of Recreational Noise Exposure on Hearing Impairment among Teenage Students

ERIC Educational Resources Information Center

Tung, Chen-Yin; Chao, Keh-Ping

2013-01-01

Several studies have focused on the potential impact of children's hearing loss on learning and development. Recently, numerous teenage students have been found to be fond of listening to music on personal devices and participating in recreational music activities. The objective of this study was to investigate teenage students' hearing…

The Development and Validation of the Social Privilege Measure

ERIC Educational Resources Information Center

Black, Linda L.; Stone, David A.; Hutchinson, Susan R.; Suarez, Elisabeth C.

2007-01-01

Privilege and oppression have an impact on society in numerous ways. Although studied in many disciplines, few empirical measures of these social constructs exist for educators or researchers. The 2 studies presented in this article describe the development and validation of the scores yielded by the Social Privilege Measure. (Contains 4 tables.)

Student Engagement in High School Physical Education: Do Social Motivation Orientations Matter?

ERIC Educational Resources Information Center

Garn, Alex; Ware, David R.; Solmon, Melinda A.

2011-01-01

High school physical education classes provide students with numerous opportunities for social interactions, but few studies have explored how social strivings impact class engagement. The purpose of this study was to investigate the relationships among 2 x 2 achievement goals, social motivation orientations, and effort in high school physical…

Incidental captures of birds in small mammal traps: a cautionary note for interdisciplinary studies.

Treesearch

David L. Waldien; Miranda M. Cooley; Jennifer Weikel; John P. Hayes; Chris C. Maguire; Tom Manning; Thomas J. Maier

2004-01-01

Although benefits of interdisciplinary studies are numerous, potential exists for data acquisition for some aspects of such studies to impact data acquisition for other aspects. This may be particularly true in studies involving both trapping of small mammals and assessment of bird populations. We summarize the incidence of birds captured during 8 research projects in...

Numerical Study of Suspension Plasma Spraying

NASA Astrophysics Data System (ADS)

Farrokhpanah, Amirsaman; Coyle, Thomas W.; Mostaghimi, Javad

2017-01-01

A numerical study of suspension plasma spraying is presented in the current work. The liquid suspension jet is replaced with a train of droplets containing the suspension particles injected into the plasma flow. Atomization, evaporation, and melting of different components are considered for droplets and particles as they travel toward the substrate. Effect of different parameters on particle conditions during flight and upon impact on the substrate is investigated. Initially, influence of the torch operating conditions such as inlet flow rate and power is studied. Additionally, effect of injector parameters like injection location, flow rate, and angle is examined. The model used in the current study takes high-temperature gradients and non-continuum effects into account. Moreover, the important effect of change in physical properties of suspension droplets as a result of evaporation is included in the model. These mainly include variations in heat transfer properties and viscosity. Utilizing this improved model, several test cases have been considered to better evaluate the effect of different parameters on the quality of particles during flight and upon impact on the substrate.

Hydrodynamic Simulations of Protoplanetary Disks with GIZMO

NASA Astrophysics Data System (ADS)

Rice, Malena; Laughlin, Greg

2018-01-01

Over the past several decades, the field of computational fluid dynamics has rapidly advanced as the range of available numerical algorithms and computationally feasible physical problems has expanded. The development of modern numerical solvers has provided a compelling opportunity to reconsider previously obtained results in search for yet undiscovered effects that may be revealed through longer integration times and more precise numerical approaches. In this study, we compare the results of past hydrodynamic disk simulations with those obtained from modern analytical resources. We focus our study on the GIZMO code (Hopkins 2015), which uses meshless methods to solve the homogeneous Euler equations of hydrodynamics while eliminating problems arising as a result of advection between grid cells. By comparing modern simulations with prior results, we hope to provide an improved understanding of the impact of fluid mechanics upon the evolution of protoplanetary disks.

Analysis of close encounters with Ganymede and Callisto using a genetic n-body algorithm

NASA Astrophysics Data System (ADS)

Winter, Philip M.; Galiazzo, Mattia A.; Maindl, Thomas I.

2018-05-01

In this work we describe a genetic algorithm which is used in order to study orbits of minor bodies in the frames of close encounters. We find that the algorithm in combination with standard orbital numerical integrators can be used as a good proxy for finding typical orbits of minor bodies in close encounters with planets and even their moons, saving a lot of computational time compared t0 long-term orbital numerical integrations. Here, we study close encounters of Centaurs with Callisto and Ganymede in particular. We also perform n-body numerical simulations for comparison. We find typical impact velocities to be between v rel = 20[v esc ] and v rel = 30[v esc ] for Ganymede and between v rel = 25[v esc ] and v rel = 35[v esc ] for Callisto.

Development of CCHE2D embankment break model

USDA-ARS?s Scientific Manuscript database

Earthen embankment breach often results in detrimental impact on downstream residents and infrastructure, especially those located in the flooding zone. Embankment failures are most commonly caused by overtopping or internal erosion. This study is to develop a practical numerical model for simulat...

Case studies of the access and mobility impact of freeway removal.

DOT National Transportation Integrated Search

2013-01-01

Throughout the United States, there is a growing movement to remove selected sections of : freeways from city centers. Largely seen as a way to restore life and vitality to these areas, this : strategy has the potential for numerous benefits includin...

Are the Effects of University Teacher Education "Washed Out" by School Experience?

ERIC Educational Resources Information Center

Zeichner, Kenneth M.; Tabachnick, B. Robert

1981-01-01

Numerous studies on the education of teachers indicate that, as students advance educationally, their attitudes and beliefs tend to become increasingly liberal and progressive. However, the impact of the college education is "washed out" by the teaching experience. (JN)

Simulation of Foam Impact Effects on Components of the Space Shuttle Thermal Protection System. Chapter 7

NASA Technical Reports Server (NTRS)

Fahrenthold, Eric P.; Park, Young-Keun

2004-01-01

A series of three dimensional simulations has been performed to investigate analytically the effect of insulating foam impacts on ceramic tile and reinforced carbon-carbon components of the Space Shuttle thermal protection system. The simulations employed a hybrid particle-finite element method and a parallel code developed for use in spacecraft design applications. The conclusions suggested by the numerical study are in general consistent with experiment. The results emphasize the need for additional material testing work on the dynamic mechanical response of thermal protection system materials, and additional impact experiments for use in validating computational models of impact effects.

The Medical Humanities Effect: a Pilot Study of Pre-Health Professions Students at the University of Rochester.

PubMed

Baker, Clayton J; Shaw, Margie Hodges; Mooney, Christopher J; Daiss, Susan Dodge-Peters; Clark, Stephanie Brown

2017-12-01

Qualitative and quantitative research on the impact of medical and health humanities teaching in baccalaureate education is sparse. This paper reviews recent studies of the impact of medical and health humanities coursework in pre-health professions education and describes a pilot study of baccalaureate students who completed semester-long medical humanities courses in the Division of Medical Humanities & Bioethics at the University of Rochester. The study format was an email survey. All participants were current or former baccalaureate students who had taken one or more courses in literature and narrative in medicine, bioethics, history of medicine, and/or visual arts and healthcare during the past four years. The survey gathered numerical data in several areas: demographic information, career plans, self-reported influence of coursework on educational and career plans, and self-reported influence of coursework on intellectual skills and abilities. It also gathered narrative commentary that elaborated on students' responses to the numerically-based questions. Notable findings from preliminary analysis of the data include higher scores of self-reported impact of the coursework on specific habits of mind and on preparedness for intended career rather than on gaining admission to future educational programs. Discussion of the results focuses on several potential future directions this type of study might take, including multi-center, longitudinal, and sequential approaches.

Objective biofidelity rating of a numerical human occupant model in frontal to lateral impact.

PubMed

de Lange, Ronald; van Rooij, Lex; Mooi, Herman; Wismans, Jac

2005-11-01

Both hardware crash dummies and mathematical human models have been developed largely using the same biomechanical data. For both, biofidelity is a main requirement. Since numerical modeling is not bound to hardware crash dummy design constraints, it allows more detailed modeling of the human and offering biofidelity for multiple directions. In this study the multi-directional biofidelity of the MADYMO human occupant model is assessed, to potentially protect occupants under various impact conditions. To evaluate the model's biofidelity, generally accepted requirements were used for frontal and lateral impact: tests proposed by EEVC and NHTSA and tests specified by ISO TR9790, respectively. A subset of the specified experiments was simulated with the human model. For lateral impact, the results were objectively rated according to the ISO protocol. Since no rating protocol was available for frontal impact, the ISO rating scheme for lateral was used for frontal, as far as possible. As a result, two scores show the overall model biofidelity for frontal and lateral impact, while individual ratings provide insight in the quality on body segment level. The results were compared with the results published for the THOR and WorldSID dummies, showing that the mathematical model exhibits a high level of multi-directional biofidelity. In addition, the performance of the human model in the NBDL 11G oblique test indicates a valid behavior of the model in intermediate directions as well. A new aspect of this study is the objective assessment of the multi-directional biofidelity of the mathematical human model according to accepted requirements. Although hardware dummies may always be used in regulations, it is expected that virtual testing with human models will serve in extrapolating outside the hardware test environment. This study was a first step towards simulating a wider range of impact conditions, such as angled impact and rollover.

How Parents Read Counting Books and Non-numerical Books to Their Preverbal Infants: An Observational Study

PubMed Central

Goldstein, Alison; Cole, Thomas; Cordes, Sara

2016-01-01

Studies have stressed the importance of counting with children to promote formal numeracy abilities; however, little work has investigated when parents begin to engage in this behavior with their young children. In the current study, we investigated whether parents elaborated on numerical information when reading a counting book to their preverbal infants and whether developmental differences in numerical input exist even in the 1st year of life. Parents and their 5–10 months old infants were asked to read, as they would at home, two books to their infants: a counting book and another book that did not have numerical content. Parents’ spontaneous statements rarely focused on number and those that did consisted primarily of counting, with little emphasis on labeling the cardinality of the set. However, developmental differences were observed even in this age range, such that parents were more likely to make numerical utterances when reading to older infants. Together, results are the first to characterize naturalistic reading behaviors between parents and their preverbal infants in the context of counting books, suggesting that although counting books promote numerical language in parents, infants still receive very little in the way of numerical input before the end of the 1st year of life. While little is known regarding the impact of number talk on the cognitive development of young infants, the current results may guide future work in this area by providing the first assessment of the characteristics of parental numerical input to preverbal infants. PMID:27493639

Methane hydrate induced permeability modification for multiphase flow in unsaturated porous media

NASA Astrophysics Data System (ADS)

Seol, Yongkoo; Kneafsey, Timothy J.

2011-08-01

An experimental study was performed using X-ray computed tomography (CT) scanning to capture three-dimensional (3-D) methane hydrate distributions and potential discrete flow pathways in a sand pack sample. A numerical study was also performed to develop and analyze empirical relations that describe the impacts of hydrate accumulation habits within pore space (e.g., pore filling or grain cementing) on multiphase fluid migration. In the experimental study, water was injected into a hydrate-bearing sand sample that was monitored using an X-ray CT scanner. The CT images were converted into numerical grid elements, providing intrinsic sample data including porosity and phase saturations. The impacts of hydrate accumulation were examined by adapting empirical relations into the flow simulations as additional relations governing the evolution of absolute permeability of hydrate bearing sediment with hydrate deposition. The impacts of pore space hydrate accumulation habits on fluid migration were examined by comparing numerical predictions with experimentally measured water saturation distributions and breakthrough curves. A model case with 3-D heterogeneous initial conditions (hydrate saturation, porosity, and water saturation) and pore body-preferred hydrate accumulations best captured water migration behavior through the hydrate-bearing sample observed in the experiment. In the best matching model, absolute permeability in the hydrate bearing sample does not decrease significantly with increasing hydrate saturation until hydrate saturation reaches about 40%, after which it drops rapidly, and complete blockage of flow through the sample can occur as hydrate accumulations approach 70%. The result highlights the importance of permeability modification due to hydrate accumulation habits when predicting multiphase flow through high-saturation, reservoir quality hydrate-bearing sediments.

Project TANDEM (Tsunamis in the Atlantic and the English ChaNnel: Definition of the Effects through numerical Modeling) (2014-2018): a French initiative to draw lessons from the Tohoku-oki tsunami on French coastal nuclear facilities

NASA Astrophysics Data System (ADS)

Hébert, Hélène; Abadie, Stéphane; Benoit, Michel; Créach, Ronan; Frère, Antoine; Gailler, Audrey; Garzaglia, Sébastien; Hayashi, Yutaka; Loevenbruck, Anne; Macary, Olivier; Marcer, Richard; Morichon, Denis; Pedreros, Rodrigo; Rebour, Vincent; Ricchiuto, Mario; Silva Jacinto, Ricardo; Terrier, Monique; Toucanne, Samuel; Traversa, Paola; Violeau, Damien

2014-05-01

TANDEM (Tsunamis in the Atlantic and the English ChaNnel: Definition of the Effects through numerical Modeling) is a French research project dedicated to the appraisal of coastal effects due to tsunami waves on the French coastlines, with a special focus on the Atlantic and Channel coastlines, where French civil nuclear facilities have been operating since about 30 years. This project aims at drawing conclusions from the 2011 catastrophic tsunami, and will allow, together with a Japanese research partner, to design, adapt and validate numerical methods of tsunami hazard assessment, using the outstanding database of the 2011 tsunami. Then the validated methods will be applied to estimate, as accurately as possible, the tsunami hazard for the French Atlantic and Channel coastlines, in order to provide guidance for risk assessment on the nuclear facilities. The project TANDEM follows the recommendations of International Atomic Energy Agency (IAEA) to analyse the tsunami exposure of the nuclear facilities, as well as the recommendations of the French Nuclear Safety Authority (Autorité de Sûreté Nucléaire, ASN) in the aftermath of the 2011 catastrophe, which required the licensee of nuclear facilities to conduct complementary safety assessments (CSA), also including "the robustness beyond their design basis". The tsunami hazard deserves an appraisal in the light of the 2011 catastrophe, to check whether any unforeseen tsunami impact can be expected for these facilities. TANDEM aims at defining the tsunami effects expected for the French Atlantic and Channel coastlines, basically from numerical modeling methods, through adaptation and improvement of numerical methods, in order to study tsunami impacts down to the interaction with coastal structures (thus sometimes using 3D approaches) (WP1). Then the methods will be tested to better characterize and quantify the associated uncertainties (in the source, the propagation, and the coastal impact) (WP2). The project will benefit from a Japanese cooperation (Meteorological Research Institute, MRI) to study in detail the coastal impact of the 2011 Tohoku tsunami (WP3). In this framework TANDEM will apply the models to the French study area, which includes investigating historical documents, defining the possible tsunamigenic sources able to strike the regions of interest (earthquakes and/or landslides), and modeling the coastal effects at a regional scale and for selected sites. Using high resolution bathymetric and topographic data in the frame of Litto3D (a French project whose main objective is to build a seamless integrated topographic and bathymetric coastal Digital Terrain Model), TANDEM will thoroughly investigate possible sources, through a detailed characterization of the slope stability off the coastlines (for the Celtic and Armorican margins, Bay of Biscay), and estimate the coastal impacts. It will also consider events (Canaries) whose assumed catastrophic impact has been widely discussed these recent years, needing a reappraisal regarding French coastlines. A special attention will also be paid to the estimation of the return periods expected for the tsunami scenarios.

The impact of vertical resolution in mesoscale model AROME forecasting of radiation fog

NASA Astrophysics Data System (ADS)

Philip, Alexandre; Bergot, Thierry; Bouteloup, Yves; Bouyssel, François

2015-04-01

Airports short-term forecasting of fog has a security and economic impact. Numerical simulations have been performed with the mesoscale model AROME (Application of Research to Operations at Mesoscale) (Seity et al. 2011). Three vertical resolutions (60, 90 and 156 levels) are used to show the impact of radiation fog on numerical forecasting. Observations at Roissy Charles De Gaulle airport are compared to simulations. Significant differences in the onset, evolution and dissipation of fog were found. The high resolution simulation is in better agreement with observations than a coarser one. The surface boundary layer and incoming long-wave radiations are better represented. A more realistic behaviour of liquid water content evolution allows a better anticipation of low visibility procedures (ceiling < 60m and/or visibility < 600m). The case study of radiation fog shows that it is necessary to have a well defined vertical grid to better represent local phenomena. A statistical study over 6 months (October 2011 - March 2012 ) using different configurations was carried out. Statistically, results were the same as in the case study of radiation fog. Seity Y., P. Brousseau, S. Malardel, G. Hello, P. Bénard, F. Bouttier, C. Lac, V. Masson, 2011: The AROME-France convective scale operational model. Mon.Wea.Rev., 139, 976-991.

Advanced numerical models and material characterisation techniques for composite materials subject to impact and shock wave loading

NASA Astrophysics Data System (ADS)

Clegg, R. A.; White, D. M.; Hayhurst, C.; Ridel, W.; Harwick, W.; Hiermaier, S.

2003-09-01

The development and validation of an advanced material model for orthotropic materials, such as fibre reinforced composites, is described. The model is specifically designed to facilitate the numerical simulation of impact and shock wave propagation through orthotropic materials and the prediction of subsequent material damage. Initial development of the model concentrated on correctly representing shock wave propagation in composite materials under high and hypervelocity impact conditions [1]. This work has now been extended to further concentrate on the development of improved numerical models and material characterisation techniques for the prediction of damage, including residual strength, in fibre reinforced composite materials. The work is focussed on Kevlar-epoxy however materials such as CFRP are also being considered. The paper describes our most recent activities in relation to the implementation of advanced material modelling options in this area. These enable refined non-liner directional characteristics of composite materials to be modelled, in addition to the correct thermodynamic response under shock wave loading. The numerical work is backed by an extensive experimental programme covering a wide range of static and dynamic tests to facilitate derivation of model input data and to validate the predicted material response. Finally, the capability of the developing composite material model is discussed in relation to a hypervelocity impact problem.

An Experimental and numerical Study for squeezing flow

NASA Astrophysics Data System (ADS)

Nathan, Rungun; Lang, Ji; Wu, Qianhong; Vucbmss Team

2017-11-01

We report an experimental and numerical study to examine the transient squeezing flow driven by sudden external impacts. The phenomenon is widely observed in industrial applications, e.g. squeeze dampers, or in biological systems, i.e. joints lubrication. However, there is a lack of investigation that captures the transient flow feature during the process. An experimental setup was developed that contains a piston instrumented with a laser displacement sensor and a pressure transducer. The heavy piston was released from rest, creating a fast compaction on the thin fluid gap underneath. The motion of the piston and the fluid pressure build-up was recorded. For this dynamic process, a CFD simulation was performed which shows excellent agreement with the experimental data. Both the numerical and experimental results show that, the squeezing flow starts with the inviscid limit when the viscous fluid effect has no time to appear, and thereafter becomes a developing flow, in which the inviscid core flow region decreases and the viscous wall region increases until the entire fluid gap is filled with viscous fluid flow. The study presented herein, filling the gap in the literature, will have broad impacts in industrial and biomedical applications. This research was supported by the National Science Foundation under Award 1511096, and supported by the Seed Grant from The Villanova Center for the Advancement of Sustainability in Engineering (VCASE).

Wavelet data compression for archiving high-resolution icosahedral model data

NASA Astrophysics Data System (ADS)

Wang, N.; Bao, J.; Lee, J.

2011-12-01

With the increase of the resolution of global circulation models, it becomes ever more important to develop highly effective solutions to archive the huge datasets produced by those models. While lossless data compression guarantees the accuracy of the restored data, it can only achieve limited reduction of data size. Wavelet transform based data compression offers significant potentials in data size reduction, and it has been shown very effective in transmitting data for remote visualizations. However, for data archive purposes, a detailed study has to be conducted to evaluate its impact to the datasets that will be used in further numerical computations. In this study, we carried out two sets of experiments for both summer and winter seasons. An icosahedral grid weather model and a highly efficient wavelet data compression software were used for this study. Initial conditions were compressed and input to the model to run to 10 days. The forecast results were then compared to those forecast results from the model run with the original uncompressed initial conditions. Several visual comparisons, as well as the statistics of numerical comparisons are presented. These results indicate that with specified minimum accuracy losses, wavelet data compression achieves significant data size reduction, and at the same time, it maintains minimum numerical impacts to the datasets. In addition, some issues are discussed to increase the archive efficiency while retaining a complete set of meta data for each archived file.

Study on the Effect of water Injection Momentum on the Cooling Effect of Rocket Engine Exhaust Plume

NASA Astrophysics Data System (ADS)

Yang, Kan; Qiang, Yanhui; Zhong, Chenghang; Yu, Shaozhen

2017-10-01

For the study of water injection momentum factors impact on flow field of the rocket engine tail flame, the numerical computation model of gas-liquid two phase flow in the coupling of high temperature and high speed gas flow and low temperature liquid water is established. The accuracy and reliability of the numerical model are verified by experiments. Based on the numerical model, the relationship between the flow rate and the cooling effect is analyzed by changing the water injection momentum of the water spray pipes. And the effective mathematical expression is obtained. What’s more, by changing the number of the water spray and using small flow water injection, the cooling effect is analyzed to check the application range of the mathematical expressions. The results show that: the impact and erosion of the gas flow field could be reduced greatly by water injection, and there are two parts in the gas flow field, which are the slow cooling area and the fast cooling area. In the fast cooling area, the influence of the water flow momentum and nozzle quantity on the cooling effect can be expressed by mathematical functions without causing bifurcation flow for the mainstream gas. The conclusion provides a theoretical reference for the engineering application.

Impact of the formaldehyde concentration in the air on the sink effect of a coating material

NASA Astrophysics Data System (ADS)

Tiffonnet, Anne-Lise; Tourreilles, Céline; Duforestel, Thierry

2018-02-01

This study aims to characterize, from a numerical modelling, the sorption behaviour of a material (a plasticised flooring material) when it is exposed to a pollutant commonly encountered in indoor environments (formaldehyde). It deals with the influence of the pollutant concentration in the room air on the sink effect of the material. The numerical simulations are based on a macroscopic modelling using experimental test results obtained elsewhere. The consequences on the room inertia are also discussed, and analogies between mass transfer and heat transfer are highlighted.

Time-domain simulation of damped impacted plates. II. Numerical model and results.

PubMed

Lambourg, C; Chaigne, A; Matignon, D

2001-04-01

A time-domain model for the flexural vibrations of damped plates was presented in a companion paper [Part I, J. Acoust. Soc. Am. 109, 1422-1432 (2001)]. In this paper (Part II), the damped-plate model is extended to impact excitation, using Hertz's law of contact, and is solved numerically in order to synthesize sounds. The numerical method is based on the use of a finite-difference scheme of second order in time and fourth order in space. As a consequence of the damping terms, the stability and dispersion properties of this scheme are modified, compared to the undamped case. The numerical model is used for the time-domain simulation of vibrations and sounds produced by impact on isotropic and orthotropic plates made of various materials (aluminum, glass, carbon fiber and wood). The efficiency of the method is validated by comparisons with analytical and experimental data. The sounds produced show a high degree of similarity with real sounds and allow a clear recognition of each constitutive material of the plate without ambiguity.

The effect of giant impactors on the magnetic field energy of an early Martian dynamo.

NASA Astrophysics Data System (ADS)

Drummond, McGregor; Thieulot, Cedric; Monteux, Julien

2016-04-01

Through the cratering record embedded on its surface, Mars is one of the key planets required for investigating the formation and impact frequency in the early history of our Solar System. This record also holds clues to the events that may have caused the observed hemispheric dichotomy and cessation of the magnetic field that was present within the first 500 Myr of the planets' formation. We investigate the influence of giant impacts on the early Martian dynamo using the numerical dynamo modelling code PARODY-JA [1]. We hypothesize that the input heat from a giant impact will decrease the total heat flux at the CMB through mantle heating which leads to a decrease in the Rayleigh number of the core. As boundary conditions for the heat flux anomaly size, we use numerical results of a 750 km diameter impactor from the Monteux and Arkani-Hamed, 2014 [2] study which investigated impact heating and core merging of giant impacts in early Mars. We also determine the decrease in Rayleigh number from the change in total heat flux at the CMB using these results, where the decrease after impact is due to shock heating at the CMB. We calculate the time-averaged total magnetic field energy for an initial homogeneous heat flux model using a range of Rayleigh numbers (5 x 103 - 1 x 10^5). The Rayleigh number is then decreased for three new models - homogeneous, north pole impact and equatorial impact - and the time-averaged energy again determined. We find that the energy decreases more in our impact models, compared with the homogeneous, along with a variation in energy between the north pole and equatorial impact models. We conclude that giant impacts in Mars' early history would have decreased the total magnetic energy of the field and the decrease in energy is also dependent on the location of the impact. The magnetic field could have been disrupted beyond recovery from a planetesimal-sized collision; such as the suggested Borealis basin forming impact, or through the cumulative effect of multiple large impactors; such as Utopia, Hellas and Isidis basin forming impacts. [1] Aubert, J., Aurnou, J. & Wicht, J., 2008. The magnetic structure of convection-driven numerical dynamos. Geophys. J. Int., 172, 945--956. [2] Monteux, J., Arkani-Hamed, J., 2014. Consequences of giant impacts in early Mars: core merging and Martian dynamo evolution. J. Geophys. Res. (Planets) 119, 480--505.

Integrated analysis of numerical weather prediction and computational fluid dynamics for estimating cross-ventilation effects on inhaled air quality inside a factory

NASA Astrophysics Data System (ADS)

Murga, Alicia; Sano, Yusuke; Kawamoto, Yoichi; Ito, Kazuhide

2017-10-01

Mechanical and passive ventilation strategies directly impact indoor air quality. Passive ventilation has recently become widespread owing to its ability to reduce energy demand in buildings, such as the case of natural or cross ventilation. To understand the effect of natural ventilation on indoor environmental quality, outdoor-indoor flow paths need to be analyzed as functions of urban atmospheric conditions, topology of the built environment, and indoor conditions. Wind-driven natural ventilation (e.g., cross ventilation) can be calculated through the wind pressure coefficient distributions of outdoor wall surfaces and openings of a building, allowing the study of indoor air parameters and airborne contaminant concentrations. Variations in outside parameters will directly impact indoor air quality and residents' health. Numerical modeling can contribute to comprehend these various parameters because it allows full control of boundary conditions and sampling points. In this study, numerical weather prediction modeling was used to calculate wind profiles/distributions at the atmospheric scale, and computational fluid dynamics was used to model detailed urban and indoor flows, which were then integrated into a dynamic downscaling analysis to predict specific urban wind parameters from the atmospheric to built-environment scale. Wind velocity and contaminant concentration distributions inside a factory building were analyzed to assess the quality of the human working environment by using a computer simulated person. The impact of cross ventilation flows and its variations on local average contaminant concentration around a factory worker, and inhaled contaminant dose, were then discussed.

The Impacts of Dry Dynamic Cores on Asymmetric Hurricane Intensification

NASA Technical Reports Server (NTRS)

Guimond, Stephen R.; Reisner, Jon M.; Marras, Simone; Giraldo, Francis X.

2016-01-01

The fundamental pathways for tropical cyclone (TC) intensification are explored by considering axisymmetric and asymmetric impulsive thermal perturbations to balanced, TC-like vortices using the dynamic cores of three different nonlinear numerical models. Attempts at reproducing the results of previous work, which used the community WRF Model, revealed a discrepancy with the impacts of purely asymmetric thermal forcing. The current study finds that thermal asymmetries can have an important, largely positive role on the vortex intensification, whereas other studies find that asymmetric impacts are negligible. Analysis of the spectral energetics of each numerical model indicates that the vortex response to asymmetric thermal perturbations is significantly damped in WRF relative to the other models. Spectral kinetic energy budgets show that this anomalous damping is primarily due to the increased removal of kinetic energy from the vertical divergence of the vertical pressure flux, which is related to the flux of inertia-gravity wave energy. The increased kinetic energy in the other two models is shown to originate around the scales of the heating and propagate upscale with time from nonlinear effects. For very large thermal amplitudes (50 K), the anomalous removal of kinetic energy due to inertia-gravity wave activity is much smaller, resulting in good agreement between models. The results of this paper indicate that the numerical treatment of small-scale processes that project strongly onto inertia-gravity wave energy can lead to significant differences in asymmetric TC intensification. Sensitivity tests with different time integration schemes suggest that diffusion entering into the implicit solution procedure is partly responsible for the anomalous damping of energy.

Reduced-form air quality modeling for community-scale applications

EPA Science Inventory

Transportation plays an important role in modern society, but its impact on air quality has been shown to have significant adverse effects on public health. Numerous reviews (HEI, CDC, WHO) summarizing findings of hundreds of studies conducted mainly in the last decade, conclude ...

Current and Emerging Water Main Relining Technologies

EPA Science Inventory

The need for investment in aging underground infrastructure has been estimated as high as $325 billion over the next 20 years (AWWA, 2001a). The impact due to the current lack of investment had been reported in numerous studies including the ASCE Infrastructure Report Card, whic...

Prioritizing the School Environment in School Violence Prevention Efforts

ERIC Educational Resources Information Center

Johnson, Sarah Lindstrom; Burke, Jessica G.; Gielen, Andrea C.

2011-01-01

Background: Numerous studies have demonstrated an association between characteristics of the school environment and the likelihood of school violence. However, little is known about the relative importance of various characteristics of the school environment or their differential impact on multiple violence outcomes. Methods: Primarily…

Measurement and Modeling of Near Road & Near-Port Air Quality

EPA Science Inventory

Air pollution from mobile sources has been identified by numerous organizations as a potential public health concern. Based upon multiple near-road and near-source monitoring studies, both busy roadways and large emission sources at ports can significantly impact local air qualit...

Impacts of Advanced Manufacturing Technology on Parametric Estimating

DTIC Science & Technology

1989-12-01

been build ( Blois , p. 65). As firms move up the levels of automation, there is a large capital investment to acquire robots, computer numerically...Affordable Acquisition Approach Study, Executive Summary, Air Force Systems Command, Andrews AFB, Maryland, February 9, 1983. Blois , K.J., "Manufacturing

Prediction of material strength and fracture of glass using the SPHINX smooth particle hydrodynamics code

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mandell, D.A.; Wingate, C.A.

1994-08-01

The design of many military devices involves numerical predictions of the material strength and fracture of brittle materials. The materials of interest include ceramics, that are used in armor packages; glass that is used in truck and jeep windshields and in helicopters; and rock and concrete that are used in underground bunkers. As part of a program to develop advanced hydrocode design tools, the authors have implemented a brittle fracture model for glass into the SPHINX smooth particle hydrodynamics code. The authors have evaluated this model and the code by predicting data from one-dimensional flyer plate impacts into glass, andmore » data from tungsten rods impacting glass. Since fractured glass properties, which are needed in the model, are not available, the authors did sensitivity studies of these properties, as well as sensitivity studies to determine the number of particles needed in the calculations. The numerical results are in good agreement with the data.« less

The impact of health literacy on cardiovascular disease

PubMed Central

Safeer, Richard S; Cooke, Catherine E; Keenan, Jann

2006-01-01

One's ability to read, listen, and comprehend health information is a vital element of maintaining and improving health. However, 90 million people in the United States exhibit less than adequate health literacy skills. Given that more than 70 million Americans suffer from cardiovascular diseases, it is certain that every physician's practice is affected by health literacy issues. Those with language and cultural issues tend to be the most affected. Yet numerous studies find physicians do a poor job of assessing their patients’ health literacy skills. Patients are also unaware of the steps they should take, and how to take them, to improve their health and prevent complications. Numerous studies find, however, that outcomes can be improved with targeted patient education and improved physician communication skills that take into account patients’ health literacy levels. Unfortunately, the health care system is only beginning to recognize this problem and take action to overcome its negative impact. By improving the communication process with patients, physicians may be able to improve cardiovascular outcomes. PMID:17323600

Numerical study of groundwater flow cycling controlled by seawater/freshwater interaction in a coastal karst aquifer through conduit network using CFPv2.

PubMed

Xu, Zexuan; Hu, Bill X; Davis, Hal; Kish, Stephen

2015-11-01

In this study, a groundwater flow cycling in a karst springshed and an interaction between two springs, Spring Creek Springs and Wakulla Springs, through a subground conduit network are numerically simulated using CFPv2, the latest research version of MODFLOW-CFP (Conduit Flow Process). The Spring Creek Springs and Wakulla Springs, located in a marine estuary and 11 miles inland, respectively, are two major groundwater discharge spots in the Woodville Karst Plain (WKP), North Florida, USA. A three-phase conceptual model of groundwater flow cycling between the two springs and surface water recharge from a major surface creek (Lost Creek) was proposed in various rainfall conditions. A high permeable subground karst conduit network connecting the two springs was found by tracer tests and cave diving. Flow rate of discharge, salinity, sea level and tide height at Spring Creek Springs could significantly affect groundwater discharge and water stage at Wakulla Springs simultaneously. Based on the conceptual model, a numerical hybrid discrete-continuum groundwater flow model is developed using CFPv2 and calibrated by field measurements. Non-laminar flows in conduits and flow exchange between conduits and porous medium are implemented in the hybrid coupling numerical model. Time-variable salinity and equivalent freshwater head boundary conditions at the submarine spring as well as changing recharges have significant impacts on seawater/freshwater interaction and springs' discharges. The developed numerical model is used to simulate the dynamic hydrological process and quantitatively represent the three-phase conceptual model from June 2007 to June 2010. Simulated results of two springs' discharges match reasonably well to measurements with correlation coefficients 0.891 and 0.866 at Spring Creeks Springs and Wakulla Springs, respectively. The impacts of sea level rise on regional groundwater flow field and relationship between the inland springs and submarine springs are evaluated as well in this study. Copyright © 2015 Elsevier B.V. All rights reserved.

Numerical study of groundwater flow cycling controlled by seawater/freshwater interaction in a coastal karst aquifer through conduit network using CFPv2

NASA Astrophysics Data System (ADS)

Xu, Zexuan; Hu, Bill X.; Davis, Hal; Kish, Stephen

2015-11-01

In this study, a groundwater flow cycling in a karst springshed and an interaction between two springs, Spring Creek Springs and Wakulla Springs, through a subground conduit network are numerically simulated using CFPv2, the latest research version of MODFLOW-CFP (Conduit Flow Process). The Spring Creek Springs and Wakulla Springs, located in a marine estuary and 11 miles inland, respectively, are two major groundwater discharge spots in the Woodville Karst Plain (WKP), North Florida, USA. A three-phase conceptual model of groundwater flow cycling between the two springs and surface water recharge from a major surface creek (Lost Creek) was proposed in various rainfall conditions. A high permeable subground karst conduit network connecting the two springs was found by tracer tests and cave diving. Flow rate of discharge, salinity, sea level and tide height at Spring Creek Springs could significantly affect groundwater discharge and water stage at Wakulla Springs simultaneously. Based on the conceptual model, a numerical hybrid discrete-continuum groundwater flow model is developed using CFPv2 and calibrated by field measurements. Non-laminar flows in conduits and flow exchange between conduits and porous medium are implemented in the hybrid coupling numerical model. Time-variable salinity and equivalent freshwater head boundary conditions at the submarine spring as well as changing recharges have significant impacts on seawater/freshwater interaction and springs' discharges. The developed numerical model is used to simulate the dynamic hydrological process and quantitatively represent the three-phase conceptual model from June 2007 to June 2010. Simulated results of two springs' discharges match reasonably well to measurements with correlation coefficients 0.891 and 0.866 at Spring Creeks Springs and Wakulla Springs, respectively. The impacts of sea level rise on regional groundwater flow field and relationship between the inland springs and submarine springs are evaluated as well in this study.

Impact of Installation Faults on Heat Pump Performance

DOE PAGES

Hourahan, Glenn; Baxter, Van D.

2015-01-01

Numerous studies and surveys indicate that typically-installed HVAC equipment operate inefficiently and waste considerable energy due to varied installation errors (faults) such as improper refrigerant charge, incorrect airflow, oversized equipment, and leaky ducts. This article summarizes the results of a large United States (U.S.) experimental/analytical study (U.S. contribution to IEA HPP Annex 36) of the impact that different faults have on the performance of an air-source heat pump (ASHP) in a typical U.S. single-family house. It combines building effects, equipment effects, and climate effects in an evaluation of the faults impact on seasonal energy consumption through simulations of the house/ASHPmore » pump system.« less

The scaling and dynamics of a projectile obliquely impacting a granular medium.

PubMed

Wang, Dengming; Ye, Xiaoyan; Zheng, Xiaojing

2012-01-01

In this paper, the dynamics of a spherical projectile obliquely impacting into a two-dimensional granular bed is numerically investigated using the discrete element method. The influences of projectile's initial velocities and impacting angles are mainly considered. Numerical results show that the relationship between the final penetration depth and the initial impact velocity is very similar to that in the vertical-impact case. However, the dependence of the stopping time on the impact velocity of the projectile exhibits critical characteristics at different impact angles: the stopping time approximately increases linearly with the impact velocity for small impact angles but decreases in an exponential form for larger impact angles, which demonstrates the existence of two different regimes at low and high impact angles. When the impact angle is regarded as a parametric variable, a phenomenological force model at large impact angles is eventually proposed based on the simulation results, which can accurately describe the nature of the resistance force exerted on the projectile by the granular medium at different impact angels during the whole oblique-impact process. The degenerate model agrees well with the existing experimental results in the vertical-impact cases.

A numerical study of vegetation impact on reducing storm surge by wetlands in a semi-enclosed estuary

USGS Publications Warehouse

Kelin, Hu; Qin, Chen; Wang, Hongqing

2014-01-01

Coastal wetlands play a unique role in extreme hurricane events. The impact of wetlands on storm surge depends on multiple factors including vegetation, landscape, and storm characteristics. The Delft3D model, in which vegetation effects on flow and turbulence are explicitly incorporated, was applied to the semi-enclosed Breton Sound (BS) estuary in coastal Louisiana to investigate the wetland impact. Guided by extensive field observations, a series of numerical experiments were conducted based on variations of actual vegetation properties and storm parameters from Hurricane Isaac in 2012. Both the vegetation-induced maximum surge reduction (MSR) and maximum surge reduction rate (MSRR) increased with stem height and stem density, and were more sensitive to stem height. The MSR and MSRR decreased significantly with increasing wind intensity. The MSRR was the highest with a fast-moving weak storm. It was also found that the MSRR varied proportionally to the expression involving the maximum bulk velocity and surge over the area of interest, and was more dependent on the maximum bulk surge. Both MSR and MSRR appeared to increase when the area of interest decreased from the whole BS estuary to the upper estuary. Within the range of the numerical experiments, the maximum simulated MSR and MSRR over the upper estuary were 0.7 m and 37%, respectively.

Cratering at the Icy Satellites: Experimental Insights

NASA Astrophysics Data System (ADS)

Bruck Syal, M.; Schultz, P. H.

2013-12-01

Impact cratering processes play a central role in shaping the evolution of icy satellites and in guiding interpretations of various geologic features at these bodies. Accurate reconstruction of icy satellite histories depends in large part upon observed impact crater size-frequency distributions. Determining the extent of impact-induced thermal processing and the retention rates for impact-delivered materials of interest, e.g. organics, at these outer solar system moons is of fundamental importance for assessing their habitability and explaining differing geophysical histories. Hence, knowledge of how the impact process operates in ices or ice-rich materials is critically important. Recent progress in the development of water equations of state, coupled with increasingly efficient 3-D hydrocode calculations, has been used to construct careful numerical studies of melt and vapor generation for water ice targets. Complementary to this approach is experimental work to constrain the effects of differing ice target conditions, including porosity, rock mass fraction, and impact angle. Here we report on results from hypervelocity impact experiments (v~5.5 km/s) into water ice targets, performed at the NASA Ames Vertical Gun Range (AVGR). The setup at the AVGR allows for the use of particulate targets, which is useful for examining the effects of target porosity. Photometry and geophysical modeling both suggest that regolith porosity at the icy satellites is significant. We use a combination of half-space and quarter-space geometries, enabling analysis of the impact-generated vapor plume (half-space geometry), along with shock wave and transient crater growth tracking in a cross-sectional view (quarter-space geometry). Evaluating the impact-generated vapor from porous (φ = 0.5) and non-porous water ice targets provides an extension to previously published vapor production results for dolomite and CO2 ice targets. For the case of a 90 degree impact into porous ice, we calculate that 0.6% of the initial kinetic energy of the impactor is partitioned into the internal energy of the vapor plume. This is slightly higher than values determined in prior studies for non-porous CO2 ice (0.2%) [Schultz, 1996]. As CO2 ice possesses a lower vaporization temperature than water ice, this effect strongly suggests a role for porosity in enhancing vaporization. This is expected, as the compaction of porous materials performs additional, irreversible PdV work on the target, causing enhanced partitioning of kinetic energy into internal energy. At oblique impact angles, plume morphology changes dramatically while vaporization is enhanced. Comparing shock wave velocity attenuation in porous materials, including mixes of materials (e.g., quartz sand and porous ice), to numerical results obtained from shock physics codes such as CTH, provides insight into how impacts into porous ice-rich materials can be most accurately numerically modeled.

Eighth Grade Social Studies Teachers' Perceptions of the Impact of Technology on Students' Learning in World History

ERIC Educational Resources Information Center

Griggs, Bridget Renee'

2010-01-01

There are many perceptions of what should be taught in the social studies classroom. With the expansive amount of information that must be transferred to students, the job of the social studies teacher is becoming more challenging. To assist with this issue, there are numerous instructional strategies that can be employed such as anticipation…

How Do Transfers Survive after "Transfer Shock"? A Longitudinal Study of Transfer Student Departure at a Four-Year Institution

ERIC Educational Resources Information Center

Ishitani, Terry T.

2008-01-01

Prompted by the notion of "Transfer Shock", numerous studies examined academic performance of transfer students at senior institutions. However, few studies are found that examine how the varying nature of semester GPAs impact subsequent persistence behavior of transfer students after the initial drop in their college GPAs. Using an institutional…

Microgrid optimal scheduling considering impact of high penetration wind generation

NASA Astrophysics Data System (ADS)

Alanazi, Abdulaziz

The objective of this thesis is to study the impact of high penetration wind energy in economic and reliable operation of microgrids. Wind power is variable, i.e., constantly changing, and nondispatchable, i.e., cannot be controlled by the microgrid controller. Thus an accurate forecasting of wind power is an essential task in order to study its impacts in microgrid operation. Two commonly used forecasting methods including Autoregressive Integrated Moving Average (ARIMA) and Artificial Neural Network (ANN) have been used in this thesis to improve the wind power forecasting. The forecasting error is calculated using a Mean Absolute Percentage Error (MAPE) and is improved using the ANN. The wind forecast is further used in the microgrid optimal scheduling problem. The microgrid optimal scheduling is performed by developing a viable model for security-constrained unit commitment (SCUC) based on mixed-integer linear programing (MILP) method. The proposed SCUC is solved for various wind penetration levels and the relationship between the total cost and the wind power penetration is found. In order to reduce microgrid power transfer fluctuations, an additional constraint is proposed and added to the SCUC formulation. The new constraint would control the time-based fluctuations. The impact of the constraint on microgrid SCUC results is tested and validated with numerical analysis. Finally, the applicability of proposed models is demonstrated through numerical simulations.

Martian Impact Craters as Revealed by MGS and Odyssey

NASA Technical Reports Server (NTRS)

Barlow, N. G.

2005-01-01

A variety of ejecta and interior morphologies were revealed for martian impact craters by Viking imagery. Numerous studies have classified these ejecta and interior morphologies and looked at how these morphologies correlate with crater diameter, latitude, terrain, and elevation [1, 2, 3, 4]. Many of these features, particularly the layered (fluidized) ejecta morphologies and central pits, have been proposed to result when the crater formed in target material containing high concentrations of volatiles. The Catalog of Large Martian Impact Craters was originally derived from the Viking 1:2,000,000 photomosaics and contains information on 42,283 impact craters 5-km diameter distributed across the entire martian surface. The information in this Catalog has been used to study the distributions of craters displaying specific ejecta and interior morphologies in an attempt to understand the environmental conditions which give rise to these features and to estimate the areal and vertical extents of subsurface volatile reservoirs [4, 5]. The Catalog is currently undergoing revision utilizing Mars Global Surveyor (MGS) and Mars Odyssey data [6]. The higher resolution multispectral imagery is resulting in numerous revisions to the original classifications and the addition of new elemental, thermophysical, and topographic data is allowing new insights into the environmental conditions under which these features form. A few of the new results from analysis of data in the revised Catalog are discussed below.

Mode coupling at connectors in mode-division multiplexed transmission over few-mode fiber.

PubMed

Vuong, Jordi; Ramantanis, Petros; Frignac, Yann; Salsi, Massimiliano; Genevaux, Philippe; Bendimerad, Djalal F; Charlet, Gabriel

2015-01-26

In mode-division multiplexed (MDM) transmission systems, mode coupling is responsible for inter-modal crosstalk. We consider the transmission of modulated signals over a few-mode fiber (FMF) having low mode coupling and large differential mode group delay in the presence of a non-ideal fiber connection responsible for extra mode coupling. In this context, we first analytically derive the coupling matrix of the multimode connector and we numerically study the dependence of the matrix coefficients as a function of the butt-joint connection characteristics. The numerical results are then validated through an experiment with a five-mode setup. Finally, through numerical simulations, we assess the impact of the connector on the signal quality investigating different receiver digital signal processing (DSP) schemes.

Dynamic one-dimensional modeling of secondary settling tanks and system robustness evaluation.

PubMed

Li, Ben; Stenstrom, M K

2014-01-01

One-dimensional secondary settling tank models are widely used in current engineering practice for design and optimization, and usually can be expressed as a nonlinear hyperbolic or nonlinear strongly degenerate parabolic partial differential equation (PDE). Reliable numerical methods are needed to produce approximate solutions that converge to the exact analytical solutions. In this study, we introduced a reliable numerical technique, the Yee-Roe-Davis (YRD) method as the governing PDE solver, and compared its reliability with the prevalent Stenstrom-Vitasovic-Takács (SVT) method by assessing their simulation results at various operating conditions. The YRD method also produced a similar solution to the previously developed Method G and Enquist-Osher method. The YRD and SVT methods were also used for a time-to-failure evaluation, and the results show that the choice of numerical method can greatly impact the solution. Reliable numerical methods, such as the YRD method, are strongly recommended.

Age-of-Air, Tape Recorder, and Vertical Transport Schemes

NASA Technical Reports Server (NTRS)

Lin, S.-J.; Einaudi, Franco (Technical Monitor)

2000-01-01

A numerical-analytic investigation of the impacts of vertical transport schemes on the model simulated age-of-air and the so-called 'tape recorder' will be presented using an idealized 1-D column transport model as well as a more realistic 3-D dynamical model. By comparing to the 'exact' solutions of 'age-of-air' and the 'tape recorder' obtainable in the 1-D setting, useful insight is gained on the impacts of numerical diffusion and dispersion of numerical schemes used in global models. Advantages and disadvantages of Eulerian, semi-Lagrangian, and Lagrangian transport schemes will be discussed. Vertical resolution requirement for numerical schemes as well as observing systems for capturing the fine details of the 'tape recorder' or any upward propagating wave-like structures can potentially be derived from the 1-D analytic model.

Identifying areas of relative change in forest fragmentation in New Hampshire between 1990 and 2000

Treesearch

Tonya Lister; Andrew Lister; William McWilliams; Rachel Riemann

2007-01-01

Forest fragmentation potentially can impact many facets of natural ecosystems. Numerous methods have been employed to assess static forest fragmentation. Few studies, however, have analyzed changes in forest fragmentation over time. In this study, we developed new classifications from Landsat imagery data acquired in 1990 and 2000 for New Hampshire, assessed...

Variability in evaluating environmental impacts of treated wood.

Treesearch

Stan Lebow; Paul Cooper; Patricia. Lebow

2004-01-01

Preservative treated wood contains components that may be toxic to non-target organisms if released into the environment in sufficient quantities. Numerous studies have been conducted to determine the rate of preservative release from treated wood and/or the extent of their subsequent accumulation in the environment. These studies have produced a wide range of results...

Variability in evaluating environmental impacts of treated wood.

Treesearch

Stan T. Lebow; Paul Cooper; Patricia K. Lebow

2004-01-01

Preservative-treated wood contains components that may be toxic to non-target organisms if released into the environment in sufficient quantities. Numerous studies have been conducted to determine the rate of preservative release from treated wood and/or the extent of their subsequent accumulation in the environment. These studies have produced a wide range of results...

Biotic resistance: Exclusion of native rodent consumers releases populations of a weak invader

Treesearch

Dean E. Pearson; Teal Potter; John L. Maron

2012-01-01

Biotic resistance is a commonly invoked hypothesis to explain why most exotic plant species naturalize at low abundance. Although numerous studies have documented negative impacts of native consumers on exotic plant performance, longer-term multi-generation studies are needed to understand how native consumer damage to exotics translates to their population-level...

An Examination of Class Size Reduction on Teaching and Learning Processes: A Theoretical Perspective

ERIC Educational Resources Information Center

Harfitt, Gary James; Tsui, Amy B. M.

2015-01-01

The question of how class size impacts on student learning has been debated for some time, not least because it has substantial financial implications for educational policy. The strength of this debate notwithstanding, results from numerous international studies have been inconclusive. The study from which this paper stems sought to conceptualise…

Prediction of the effect of temperature on impact damage in carbon/epoxy laminates

NASA Astrophysics Data System (ADS)

Gómez del Río, T.; Zaera, R.; Navarro, C.

2003-09-01

The effect of temperature on impact damage in Carbon Fiber Reinforced Plastic (CFRP) tape laminates produced by low velocity impact was studied by numerical simulations made to model drop weight tower impact tests on carbon/epoxy laminate composites. The damage model was implemented into a user subroutine of the finite element code ABAQUS. The model takes into account the thermal stresses resulting form the different thermal expansion coefficients in each ply of the laminate. The tests and simulations show how temperature affects the propagation of each damage mode. Matrix cracking and delamination are greatly affected by low temperature, white matrix crushing and fibre failure appear only in a small region at all the impact energies and test temperatures.

Assessing the environmental impact of energy production from hydrochar generated via hydrothermal carbonization waste management

USDA-ARS?s Scientific Manuscript database

Hydrothermal carbonization (HTC) is a relatively low temperature thermal conversion process that is gaining significant attention as a sustainable and environmentally beneficial approach for the transformation of biomass and waste streams to value-added products. Although there are numerous studies ...

RESTORATION OF MUNICIPAL DRINKING WATER SUPPLY WELLS IMPACTED BY NATURALLY OCCURRING ARSENIC

EPA Science Inventory

Studies have indicated that arsenic concentrations greater than the newly proposed U.S. Environmental Protection Agency (EPA) maximum contaminant level (MCL) of 10 micrograms per liter (ug/L) occur in specific parts of numerous aquifers around the United States. One such aquifer...

The Myth of the "Green Student": Student Involvement in Australian University Sustainability Programmes

ERIC Educational Resources Information Center

Butt, L.; More, E.; Avery, G. C.

2014-01-01

The paper questions the prevalence of "green students" and their impact on decision-making in sustainability programmes in Australian universities. While the universities studied provide numerous opportunities for student involvement in sustainability programmes, comparatively few students actually become involved, making student impact…

Oceanic Impact: Mechanisms and Environmental Perturbations

NASA Technical Reports Server (NTRS)

Gersonde, Rainer (Editor); Deutsch, Alex (Editor); Ivanov, Boris A. (Editor); Kyte, Frank T. (Editor)

2002-01-01

The contents include the following: Oceanic impacts-a growing field of fundamental geoscience. Shock metamorphism on the ocean floor (numerical simulations). Numerical modeling of impact-induced modifications of the deep-sea floor. Computer modelling of the water resurge at a marine impact: the Lockne crater, Sweden. Experimental investigation of the role of water in impact vaporization chemistry. Calcareous plankton stratigraphy around the Pliocene Eltanin asteroid impact area (SE Pacific): documentation and application for geological and paleoceanographic reconstruction. Composition of impact melt debris from the Eltanin impact strewn field, Bellingshausen Sea. Iridium concentrations and abundances of meteoritic ejecta from the Eltanin impact in sediment cores from Polarstern expedition ANT XII/4. Unmelted meteoritic debris collected from Eltanin ejecta in Polarstern cores from expedition ANT XII/4. Impact tsunami-Eltanin. Ancient impact structures on modern continental shelves: The Chesapeake Bay, Montagnais, and Toms Canyon craters, Atlantic margin of North America. The Mjolnir marine impact crater porosity anomaly. Kardla (Hiiu-maa Island, Estonia) - the buried and well-preserved Ordovician marine impact structure. Long-term effect of the Kardla crater (Hiiu-maa, Estonia) on Late Ordovician carbonate sedimentation. The middle Devonian Kaluga impact crater (Russia): new interpretation of marine setting.

Plasmonic Light Trapping in Thin-Film Solar Cells: Impact of Modeling on Performance Prediction

PubMed Central

Micco, Alberto; Pisco, Marco; Ricciardi, Armando; Mercaldo, Lucia V.; Usatii, Iurie; La Ferrara, Vera; Delli Veneri, Paola; Cutolo, Antonello; Cusano, Andrea

2015-01-01

We present a comparative study on numerical models used to predict the absorption enhancement in thin-film solar cells due to the presence of structured back-reflectors exciting, at specific wavelengths, hybrid plasmonic-photonic resonances. To evaluate the effectiveness of the analyzed models, they have been applied in a case study: starting from a U-shaped textured glass thin-film, µc-Si:H solar cells have been successfully fabricated. The fabricated cells, with different intrinsic layer thicknesses, have been morphologically, optically and electrically characterized. The experimental results have been successively compared with the numerical predictions. We have found that, in contrast to basic models based on the underlying schematics of the cell, numerical models taking into account the real morphology of the fabricated device, are able to effectively predict the cells performances in terms of both optical absorption and short-circuit current values.

Dispersive effects on multicomponent transport through porous media

NASA Astrophysics Data System (ADS)

Dutta, Sourav; Daripa, Prabir

2017-11-01

We use a hybrid numerical method to solve a global pressure based porous media flow model of chemical enhanced oil recovery. This is an extension of our recent work. The numerical method is based on the use of a discontinuous finite element method and the modified method of characteristics. The impact of molecular diffusion and mechanical dispersion on the evolution of scalar concentration distributions are studied through numerical simulations of various flooding schemes. The relative importance of the advective, capillary diffusive and dispersive fluxes are compared over different flow regimes defined in the parameter space of Capillary number, Peclet number, longitudinal and transverse dispersion coefficients. Such studies are relevant for the design of effective injection policies and determining optimal combinations of chemical components for improving recovery. This work has been possible due to financial support from the U.S. National Science Foundation Grant DMS-1522782.

Climate change, air pollution and human health in Sydney, Australia: A review of the literature

NASA Astrophysics Data System (ADS)

Dean, Annika; Green, Donna

2018-05-01

Sydney is Australia’s largest city and is growing rapidly. Although Sydney’s air quality is relatively good compared to the major cities in many industrialised countries, particulate matter (PM) and ozone (O3) occasionally exceed the national health standards and are the cause of premature mortalities and hospital admissions. Numerous studies from overseas (e.g. North America and continental Europe) suggest that climate change may impact air quality to the detriment of human health. There is limited knowledge about how climate change may impact air quality in Sydney. This study reviews the available literature on the impacts of climate change on air quality related health impacts in Sydney to identify knowledge and research gaps. Where no studies are available for Sydney, it draws on relevant studies from other Australian cities and overseas. Our findings summarise what is known about how climate change may impact air quality in Sydney and where research gaps exist. This approach can facilitate research agendas, policies and planning strategies that mitigate public health impacts and tackle climate change and air pollution in a coordinated way.

Sleep-obesity relation: underlying mechanisms and consequences for treatment.

PubMed

St-Onge, M-P

2017-02-01

Short sleep duration has been associated with obesity in numerous epidemiological studies. However, such association studies cannot establish evidence of causality. Clinical intervention studies, on the other hand, can provide information on a causal effect of sleep duration on markers of weight gain: energy intake and energy expenditure. Herein is an overview of the science related to the impact of sleep restriction, in the context of clinical intervention studies, on energy intake, energy expenditure and body weight. Additionally, studies that evaluate the impact of sleep restriction on weight loss and the impact of sleep extension on appetite are discussed. Information to date suggests that weight management is hindered when attempted in the context of sleep restriction, and the public should be made aware of the negative consequences of sleep restriction for weight regulation. © 2017 World Obesity Federation.

Enviro-HIRLAM/ HARMONIE Studies in ECMWF HPC EnviroAerosols Project

NASA Astrophysics Data System (ADS)

Hansen Sass, Bent; Mahura, Alexander; Nuterman, Roman; Baklanov, Alexander; Palamarchuk, Julia; Ivanov, Serguei; Pagh Nielsen, Kristian; Penenko, Alexey; Edvardsson, Nellie; Stysiak, Aleksander Andrzej; Bostanbekov, Kairat; Amstrup, Bjarne; Yang, Xiaohua; Ruban, Igor; Bergen Jensen, Marina; Penenko, Vladimir; Nurseitov, Daniyar; Zakarin, Edige

2017-04-01

The EnviroAerosols on ECMWF HPC project (2015-2017) "Enviro-HIRLAM/ HARMONIE model research and development for online integrated meteorology-chemistry-aerosols feedbacks and interactions in weather and atmospheric composition forecasting" is aimed at analysis of importance of the meteorology-chemistry/aerosols interactions and to provide a way for development of efficient techniques for on-line coupling of numerical weather prediction and atmospheric chemical transport via process-oriented parameterizations and feedback algorithms, which will improve both the numerical weather prediction and atmospheric composition forecasts. Two main application areas of the on-line integrated modelling are considered: (i) improved numerical weather prediction with short-term feedbacks of aerosols and chemistry on formation and development of meteorological variables, and (ii) improved atmospheric composition forecasting with on-line integrated meteorological forecast and two-way feedbacks between aerosols/chemistry and meteorology. During 2015-2016 several research projects were realized. At first, the study on "On-line Meteorology-Chemistry/Aerosols Modelling and Integration for Risk Assessment: Case Studies" focused on assessment of scenarios with accidental and continuous emissions of sulphur dioxide for case studies for Atyrau (Kazakhstan) near the northern part of the Caspian Sea and metallurgical enterprises on the Kola Peninsula (Russia), with GIS integration of modelling results into the RANDOM (Risk Assessment of Nature Detriment due to Oil spill Migration) system. At second, the studies on "The sensitivity of precipitation simulations to the soot aerosol presence" & "The precipitation forecast sensitivity to data assimilation on a very high resolution domain" focused on sensitivity and changes in precipitation life-cycle under black carbon polluted conditions over Scandinavia. At third, studies on "Aerosol effects over China investigated with a high resolution convection permitting weather model" & "Meteorological and chemical urban scale modelling for Shanghai metropolitan area" with focus on aerosol effects and influence of urban areas in China at regional-subregional-urban scales. At fourth, study on "Direct variational data assimilation algorithm for atmospheric chemistry data with transport and transformation model" with focus on testing chemical data assimilation algorithm of in situ concentration measurements on real data scenario. At firth, study on "Aerosol influence on High Resolution NWP HARMONIE Operational Forecasts" with focus on impact of sea salt aerosols on numerical weather prediction during low precipitation events. And finally, study on "Impact of regional afforestation on climatic conditions in metropolitan areas: case study of Copenhagen" with focus on impact of forest and land-cover change on formation and development of temperature regimes in the Copenhagen metropolitan area of Denmark. Selected results and findings will be presented and discussed.

The impact of tinnitus upon cognition in adults: A systematic review.

PubMed

Tegg-Quinn, Susan; Bennett, Rebecca J; Eikelboom, Robert H; Baguley, David M

2016-10-01

To systematically review and analyse experimental outcomes of studies exploring the impact of tinnitus upon cognitive function and their implications for clinical management of invasive tinnitus. A systematic and descriptive review. Eighteen studies were identified investigating the impact of tinnitus on cognitive function. The 18 studies evaluated cognitive function using 24 different objective behavioural tests, nine electrophysiological recordings, one oculomotor test, and one self-report questionnaire. The studies spanned 18 years and revealed numerous interactions potentially contributing to the cognitive difficulties frequently reported by people with invasive tinnitus. The studies indicate a clear association between tinnitus and aspects of cognitive function, specifically the executive control of attention. Tinnitus impairs cognitive function by way of impact upon executive control of attention. Clinical management of patients reporting tinnitus and cognitive difficulties requires an understanding of the reciprocal relationship between tinnitus and cognitive function, with additive effects of anxiety, depression, and somatic cognitive bias. Further study is required to establish the impact of advancing age, hearing loss, anxiety, depression tinnitus duration, and distress upon cognitive function in people with invasive tinnitus.

Quantitative impact of aerosols on numerical weather prediction. Part I: Direct radiative forcing

NASA Astrophysics Data System (ADS)

Marquis, J. W.; Zhang, J.; Reid, J. S.; Benedetti, A.; Christensen, M.

2017-12-01

While the effects of aerosols on climate have been extensively studied over the past two decades, the impacts of aerosols on operational weather forecasts have not been carefully quantified. Despite this lack of quantification, aerosol plumes can impact weather forecasts directly by reducing surface reaching solar radiation and indirectly through affecting remotely sensed data that are used for weather forecasts. In part I of this study, the direct impact of smoke aerosol plumes on surface temperature forecasts are quantified using a smoke aerosol event affecting the United States Upper-Midwest in 2015. NCEP, ECMWF and UKMO model forecast surface temperature uncertainties are studied with respect to aerosol loading. Smoke aerosol direct cooling efficiencies are derived and the potential of including aerosol particles in operational forecasts is discussed, with the consideration of aerosol trends, especially over regions with heavy aerosol loading.

Quantitative impact of aerosols on numerical weather prediction. Part II: Impacts to IR radiance assimilation

NASA Astrophysics Data System (ADS)

Marquis, J. W.; Campbell, J. R.; Oyola, M. I.; Ruston, B. C.; Zhang, J.

2017-12-01

This is part II of a two-part series examining the impacts of aerosol particles on weather forecasts. In this study, the aerosol indirect effects on weather forecasts are explored by examining the temperature and moisture analysis associated with assimilating dust contaminated hyperspectral infrared radiances. The dust induced temperature and moisture biases are quantified for different aerosol vertical distribution and loading scenarios. The overall impacts of dust contamination on temperature and moisture forecasts are quantified over the west coast of Africa, with the assistance of aerosol retrievals from AERONET, MPL, and CALIOP. At last, methods for improving hyperspectral infrared data assimilation in dust contaminated regions are proposed.

Explicit Finite Element Modeling of Multilayer Composite Fabric for Gas Turbine Engine Containment Systems. Part 2; Ballistic Impact Testing

NASA Technical Reports Server (NTRS)

Pereira, J. M.; Revilock, D. M.

2004-01-01

Under the Federal Aviation Administration's Airworthiness Assurance Center of Excellence and the Aircraft Catastrophic Failure Prevention Program, National Aeronautics and Space Administration Glenn Research Center collaborated with Arizona State University, Honeywell Engines, Systems and Services, and SRI International to develop improved computational models for designing fabric-based engine containment systems. In the study described in this report, ballistic impact tests were conducted on layered dry fabric rings to provide impact response data for calibrating and verifying the improved numerical models. This report provides data on projectile velocity, impact and residual energy, and fabric deformation for a number of different test conditions.

Numerical simulation of vehicle crashworthiness and occupant protection

NASA Astrophysics Data System (ADS)

Saha, Nripen K.

1993-08-01

Numerical simulation of vehicle crashworthiness and occupant protection are addressed. The vehicle crashworthiness design objectives are to design the vehicle structure for optimum impact energy absorption, and to design the restraint system (seatbelts, airbags, bolsters, etc.) for optimum occupant protection. The following approaches are taken; a major part of the impact energy is to be absorbed by the vehicle structure; the restraint components will provide protection against the remaining crash energy; certain vehicle components are designed to deform under specific types and speeds of impact in a desired mode for sound energy management; structural components such as front side rails, rear rails, door structure and pillars undergo large amounts of deformation; and with properly designed geometry and material these components assist in mitigating the effects of impact.

Numerical simulation of vehicle crashworthiness and occupant protection

NASA Technical Reports Server (NTRS)

Saha, Nripen K.

1993-01-01

Numerical simulation of vehicle crashworthiness and occupant protection are addressed. The vehicle crashworthiness design objectives are to design the vehicle structure for optimum impact energy absorption, and to design the restraint system (seatbelts, airbags, bolsters, etc.) for optimum occupant protection. The following approaches are taken; a major part of the impact energy is to be absorbed by the vehicle structure; the restraint components will provide protection against the remaining crash energy; certain vehicle components are designed to deform under specific types and speeds of impact in a desired mode for sound energy management; structural components such as front side rails, rear rails, door structure and pillars undergo large amounts of deformation; and with properly designed geometry and material these components assist in mitigating the effects of impact.

Explicit Finite Element Modeling of Multilayer Composite Fabric for Gas Turbine Engine Containment Systems, Phase II. Part 2; Ballistic Impact Testing

NASA Technical Reports Server (NTRS)

Revilock, D. M.; Pereira, J. M.

2009-01-01

This report summarizes the ballistic impact testing that was conducted to provide validation data for the development of numerical models of blade-out events in fabric containment systems. The ballistic impact response of two different fiber materials - Kevlar(TradeName) 49 and Zylon(TradeName) AS (as spun) was studied by firing metal projectiles into dry woven fabric specimens using a gas gun. The shape, mass, orientation, and velocity of the projectile were varied and recorded. In most cases, the tests were designed so the projectile would perforate the specimen, allowing measurement of the energy absorbed by the fabric. The results for both Zylon and Kevlar presented here represent a useful set of data for the purposes of establishing and validating numerical models to predict the response of fabrics under conditions that simulate those of a jet engine blade-release situation. In addition, some useful empirical observations were made regarding the effects of projectile orientation and the relative performance of the different fabric materials.

FAA Development of Reliable Modeling Methodologies for Fan Blade Out Containment Analysis. Part 2; Ballistic Impact Testing

NASA Technical Reports Server (NTRS)

Revilock, Duane M.; Pereira, J. Michael

2008-01-01

This report summarizes the ballistic impact testing that was conducted to provide validation data for the development of numerical models of blade out events in fabric containment systems. The ballistic impact response of two different fiber materials - Kevlar 49 (E.I. DuPont Nemours and Company) and Zylon AS (Toyobo Co., Ltd.) was studied by firing metal projectiles into dry woven fabric specimens using a gas gun. The shape, mass, orientation and velocity of the projectile were varied and recorded. In most cases the tests were designed such that the projectile would perforate the specimen, allowing measurement of the energy absorbed by the fabric. The results for both Zylon and Kevlar presented here represent a useful set of data for the purposes of establishing and validating numerical models for predicting the response of fabrics under conditions simulating those of a jet engine blade release situations. In addition some useful empirical observations were made regarding the effects of projectile orientation and the relative performance of the different materials.

Depiction of interfacial morphology in impact welded Ti/Cu bimetallic systems using smoothed particle hydrodynamics

NASA Astrophysics Data System (ADS)

Nassiri, Ali; Vivek, Anupam; Abke, Tim; Liu, Bert; Lee, Taeseon; Daehn, Glenn

2017-06-01

Numerical simulations of high-velocity impact welding are extremely challenging due to the coupled physics and highly dynamic nature of the process. Thus, conventional mesh-based numerical methodologies are not able to accurately model the process owing to the excessive mesh distortion close to the interface of two welded materials. A simulation platform was developed using smoothed particle hydrodynamics, implemented in a parallel architecture on a supercomputer. Then, the numerical simulations were compared to experimental tests conducted by vaporizing foil actuator welding. The close correspondence of the experiment and modeling in terms of interface characteristics allows the prediction of local temperature and strain distributions, which are not easily measured.

On the impact of atmospheric thermal stability on the characteristics of nocturnal downslope flows

NASA Astrophysics Data System (ADS)

Ye, Z. J.; Garratt, J. R.; Segal, M.; Pielke, R. A.

1990-04-01

The impacts of background (or ambient) and local atmospheric thermal stabilities, and slope steepness, on nighttime thermally induced downslope flow in meso-β domains (i.e., 20 200 km horizontal extent) have been investigated using analytical and numerical model approaches. Good agreement between the analytical and numerical evaluations was found. It was concluded that: (i) as anticipated, the intensity of the downslope flow increases with increased slope steepness, although the depth of the downslope flow was found to be insensitive to slope steepness in the studied situations; (ii) the intensity of the downslope flow is generally independent of background atmospheric thermal stability; (iii) for given integrated nighttime cooling across the nocturnal boundary layer (NBL), Q s the local atmospheric thermal stability exerts a strong influence on downslope flow behavior: the downslope flow intensity increases when local atmospheric thermal stability increases; and (iv) the downslope flow intensity is proportional to Q s 1/2.

A Numerical Study of Projectile Impact on Explosives

DTIC Science & Technology

1977-04-01

Whitbreac5 and Dewey and Slade6 performed and analyzed this type of test for charges which were unconfined or confined only on the impacted surface...With such charges one observes either that the charge detorxates or is shattered and the result is recorded as no reaction. Dewey and Slade, and Brown...detonations. At the onset of this work, we expectrd that plastic 5. S. Brown and E. Whitbread, Les Ondes de Detonation, 1961. 6. J. Dewey and D. Slade

Evaluating simulant materials for understanding cranial backspatter from a ballistic projectile.

PubMed

Das, Raj; Collins, Alistair; Verma, Anurag; Fernandez, Justin; Taylor, Michael

2015-05-01

In cranial wounds resulting from a gunshot, the study of backspatter patterns can provide information about the actual incidents by linking material to surrounding objects. This study investigates the physics of backspatter from a high-speed projectile impact and evaluates a range of simulant materials using impact tests. Next, we evaluate a mesh-free method called smoothed particle hydrodynamics (SPH) to model the splashing mechanism during backspatter. The study has shown that a projectile impact causes fragmentation at the impact site, while transferring momentum to fragmented particles. The particles travel along the path of least resistance, leading to partial material movement in the reverse direction of the projectile motion causing backspatter. Medium-density fiberboard is a better simulant for a human skull than polycarbonate, and lorica leather is a better simulant for a human skin than natural rubber. SPH is an effective numerical method for modeling the high-speed impact fracture and fragmentations. © 2015 American Academy of Forensic Sciences.

Violent transient sloshing-wave interaction with a baffle in a three-dimensional numerical tank

NASA Astrophysics Data System (ADS)

Xue, Mi-An; Zheng, Jinhai; Lin, Pengzhi; Xiao, Zhong

2017-08-01

A finite difference model for solving Navier Stokes equations with turbulence taken into account is used to investigate viscous liquid sloshing-wave interaction with baffles in a tank. The volume-of-fluid and virtual boundary force methods are employed to simulate free surface flow interaction with structures. A liquid sloshing experimental apparatus was established to evaluate the accuracy of the proposed model, as well as to study nonlinear sloshing in a prismatic tank with the baffles. Damping effects of sloshing in a rectangular tank with bottom-mounted vertical baffles and vertical baffles touching the free surface are studied numerically and experimentally. Good agreement is obtained between the present numerical results and experimental data. The numerical results match well with the current experimental data for strong nonlinear sloshing with large free surface slopes. The reduction in sloshing-wave elevation and impact pressure induced by the bottom-mounted vertical baffle and the vertical baffle touching the free surface is estimated by varying the external excitation frequency and the location and height of the vertical baffle under horizontal excitation.

Study of radon dispersion in typical dwelling using CFD modeling combined with passive-active measurements

NASA Astrophysics Data System (ADS)

Rabi, R.; Oufni, L.

2017-10-01

Inhalation of radon (222Rn) and its decay products are a major source of natural radiation exposure. It is known from recent surveys in many countries that radon and its progeny contribute significantly to total inhalation dose and it is fairly established that radon when inhaled in large quantity causes lung disorder. Indoor air conditions and ventilation systems strongly influence the indoor radon concentration. This study focuses on investigating both numerically and experimentally the influence of environmental conditions on the indoor radon concentration and spatial distribution. The numerical results showed that ventilation rate, temperature and humidity have significant impacts on both radon content and distribution. The variations of radon concentration with the ventilation, temperature and relative humidity are discussed. The measurement results show the diurnal variations of the indoor radon concentration are found to exhibit a positive correlation with relative humidity and negatively correlate with the air temperature. The analytic solution is used to validate the numeric results. The comparison amongst analytical, numerical and measurement results shows close agreement.

Faster and More Accurate Transport Procedures for HZETRN

NASA Technical Reports Server (NTRS)

Slaba, Tony C.; Blattnig, Steve R.; Badavi, Francis F.

2010-01-01

Several aspects of code verification are examined for HZETRN. First, a detailed derivation of the numerical marching algorithms is given. Next, a new numerical method for light particle transport is presented, and improvements to the heavy ion transport algorithm are discussed. A summary of various coding errors is also given, and the impact of these errors on exposure quantities is shown. Finally, a coupled convergence study is conducted. From this study, it is shown that past efforts in quantifying the numerical error in HZETRN were hindered by single precision calculations and computational resources. It is also determined that almost all of the discretization error in HZETRN is caused by charged target fragments below 50 AMeV. Total discretization errors are given for the old and new algorithms, and the improved accuracy of the new numerical methods is demonstrated. Run time comparisons are given for three applications in which HZETRN is commonly used. The new algorithms are found to be almost 100 times faster for solar particle event simulations and almost 10 times faster for galactic cosmic ray simulations.

Development of CCHE2D embankment break model

USDA-ARS?s Scientific Manuscript database

Flooding due to breaching of earth embankments often results in detrimental impact on the people and their properties in the flooding zone. The embankment breaching process is often caused by overtopping of excessive water in a reservoir or a river. This study is to develop a practical numerical m...

Educational Technologies for Precollege Engineering Education

ERIC Educational Resources Information Center

Riojas, M.; Lysecky, S.; Rozenblit, J.

2012-01-01

Numerous efforts seek to increase awareness, interest, and participation in scientific and technological fields at the precollege level. Studies have shown these students are at a critical age where exposure to engineering and other related fields such as science, mathematics, and technology greatly impact their career goals. A variety of advanced…

A Systematic Framework for Entrepreneurship Education within a University Context

ERIC Educational Resources Information Center

Ghina, Astri; Simatupang, Togar M.; Gustomo, Aurik

2014-01-01

The importance of entrepreneurship education that positively impact on the creation of new ventures has been widely recognized. Although numerous studies of entrepreneurship education have been conducted within a university setting, the results are mostly fragmented. Therefore, by using a systematic framework, this research is focused on examining…

Effects of Post-Encoding Stress on Performance in the DRM False Memory Paradigm

ERIC Educational Resources Information Center

Pardilla-Delgado, Enmanuelle; Alger, Sara E.; Cunningham, Tony J.; Kinealy, Brian; Payne, Jessica D.

2016-01-01

Numerous studies have investigated how stress impacts veridical memory, but how stress influences false memory formation remains poorly understood. In order to target memory consolidation specifically, a psychosocial stress (TSST) or control manipulation was administered following encoding of 15 neutral, semantically related word lists (DRM false…

A Feasibility Study on Numerical Modeling of Large-Scale Naval Fluid-Filled Structure: Contact-Impact Problems

DTIC Science & Technology

2011-02-01

capabilities for airbags , sensors, and seatbelts have tailored the code for applications in the automotive industry. Currently the code contains...larger intervals. In certain contact scenarios where contacting parts are moving relative to each other in a rapid fashion, such as airbag deployment

Spatial, temporal, and experimental: three study-design cornerstones for establishing defensible numeric criteria for freshwater ecosystems

USDA-ARS?s Scientific Manuscript database

Robust stressor-response measures are needed to inform nutrient criteria development and protect inland waters from impacts associated with eutrophication. We tested a framework to help inform criteria development that relies on assessing stream assemblage responses to phosphorus (P) enrichment acro...

Potential for Siting New Water Wells and Restoring Existing Wells in Arsenic-Impacted Aquifers

EPA Science Inventory

Studies have indicated that arsenic concentrations greater than the new U.S. Environmental Protection Agency (EPA) maximum contaminant level (MCL) concentration of 10 micrograms per liter (ug/L) occur in numerous aquifers around the United States. One such aquifer is the Central ...

TREATMENT OF LONG-EVANS RATS WITH A DEFINED MIXTURE OF DRINKING WATER DISINFECTION BY-PRODUCTS IMPACTS INTESTINAL MICROBIAL METABOLISM.

EPA Science Inventory

Water treatment results in the production of numerous halogenated disinfection by-products (DBPs), and has been associated with human colorectal cancer. Because the intestinal microbiota can bioactivate promutagens and procarcinogens, several studies have been done to examine the...

Mobbing and Stress

ERIC Educational Resources Information Center

Yaman, Erkan

2015-01-01

Mobbing is an important construct which has impact on the numerous psychological variables. The purpose of this study is to examine the relationships between mobbing and stress. Participants were 436 teachers (206 (55%) were female, 230 (45%) were male) from Sakarya, Turkey. Their ages ranged from 26 to 55 years and the mean age of the…

Modeling Student Success in Engineering Education

ERIC Educational Resources Information Center

Jin, Qu

2013-01-01

In order for the United States to maintain its global competitiveness, the long-term success of our engineering students in specific courses, programs, and colleges is now, more than ever, an extremely high priority. Numerous studies have focused on factors that impact student success, namely academic performance, retention, and/or graduation.…

Psychoeducational Implications of Sex Chromosome Anomalies

ERIC Educational Resources Information Center

Wodrich, David L.; Tarbox, Jennifer

2008-01-01

Numerous anomalies involving the sex chromosomes (X or Y) have been documented and their impact on development, learning, and behavior studied. This article reviews three of these disorders, Turner syndrome, Klinefelter syndrome, and Lesch-Nyhan disease. Each of these three is associated with one or more selective impairments or behavioral…

Content Analysis of Science Teacher Representations in Google Images

ERIC Educational Resources Information Center

Bergman, Daniel

2017-01-01

Teacher images can impact numerous perceptions in educational settings, as well as through popular media. The portrayal of effective science teaching is especially challenging to specify, given the complex nature of science inquiry and other standards-based practices. The present study examined the litany of representations of science teachers…

Parameter assessment for virtual Stackelberg game in aerodynamic shape optimization

NASA Astrophysics Data System (ADS)

Wang, Jing; Xie, Fangfang; Zheng, Yao; Zhang, Jifa

2018-05-01

In this paper, parametric studies of virtual Stackelberg game (VSG) are conducted to assess the impact of critical parameters on aerodynamic shape optimization, including design cycle, split of design variables and role assignment. Typical numerical cases, including the inverse design and drag reduction design of airfoil, have been carried out. The numerical results confirm the effectiveness and efficiency of VSG. Furthermore, the most significant parameters are identified, e.g. the increase of design cycle can improve the optimization results but it will also add computational burden. These studies will maximize the productivity of the effort in aerodynamic optimization for more complicated engineering problems, such as the multi-element airfoil and wing-body configurations.

Numerical study of core formation of asymmetrically driven cone-guided targets

DOE PAGES

Sawada, Hiroshi; Sakagami, Hitoshi

2017-09-22

Compression of a directly driven fast ignition cone-sphere target with a finite number of laser beams is numerically studied using a three-dimensional hydrodynamics code IMPACT-3D. The formation of a dense plasma core is simulated for 12-, 9-, 6-, and 4-beam configurations of the GEKKO XII laser. The complex 3D shapes of the cores are analyzed by elucidating synthetic 2D x-ray radiographic images in two orthogonal directions. Finally, the simulated x-ray images show significant differences in the core shape between the two viewing directions and rotation of the stagnating core axis in the top view for the axisymmetric 9- and 6-beammore » configurations.« less

Numerical study of core formation of asymmetrically driven cone-guided targets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sawada, Hiroshi; Sakagami, Hitoshi

Compression of a directly driven fast ignition cone-sphere target with a finite number of laser beams is numerically studied using a three-dimensional hydrodynamics code IMPACT-3D. The formation of a dense plasma core is simulated for 12-, 9-, 6-, and 4-beam configurations of the GEKKO XII laser. The complex 3D shapes of the cores are analyzed by elucidating synthetic 2D x-ray radiographic images in two orthogonal directions. Finally, the simulated x-ray images show significant differences in the core shape between the two viewing directions and rotation of the stagnating core axis in the top view for the axisymmetric 9- and 6-beammore » configurations.« less

A numerical study of the ex-ROFI of the Colorado River

NASA Astrophysics Data System (ADS)

Carbajal, N.; Souza, A.; Durazo, R.

1997-08-01

The freshwater discharge of the Colorado River into the Gulf of California has been reduced to negligible quantities since the construction of the Hoover Dam in 1935. These radical anthropogenic changes in the hydrography of the Colorado River Delta had striking repercussions on both physical and biological processes. Using historical river discharge data, the changes in the flow dynamics and hydrographic patterns before and after the drastic freshwater reduction are studied numerically, using a three-dimensional nonlinear shelf model. The results are applied to assess the environmental impact of the reduction of river discharge on the area. Satellite imagery is also used to compare our results with observed fronts.

Numerical study of ambient pressure for laser-induced bubble near a rigid boundary

NASA Astrophysics Data System (ADS)

Li, BeiBei; Zhang, HongChao; Han, Bing; Lu, Jian

2012-07-01

The dynamics of the laser-induced bubble at different ambient pressures was numerically studied by Finite Volume Method (FVM). The velocity of the bubble wall, the liquid jet velocity at collapse, and the pressure of the water hammer while the liquid jet impacting onto the boundary are found to increase nonlinearly with increasing ambient pressure. The collapse time and the formation time of the liquid jet are found to decrease nonlinearly with increasing ambient pressure. The ratios of the jet formation time to the collapse time, and the displacement of the bubble center to the maximal radius while the jet formation stay invariant when ambient pressure changes. These ratios are independent of ambient pressure.

Does surface roughness influence the primary stability of acetabular cups? A numerical and experimental biomechanical evaluation.

PubMed

Le Cann, Sophie; Galland, Alexandre; Rosa, Benoît; Le Corroller, Thomas; Pithioux, Martine; Argenson, Jean-Noël; Chabrand, Patrick; Parratte, Sébastien

2014-09-01

Most acetabular cups implanted today are press-fit impacted cementless. Anchorage begins with the primary stability given by insertion of a slightly oversized cup. This primary stability is key to obtaining bone ingrowth and secondary stability. We tested the hypothesis that primary stability of the cup is related to surface roughness of the implant, using both an experimental and a numerical models to analyze how three levels of surface roughness (micro, macro and combined) affect the primary stability of the cup. We also investigated the effect of differences in diameter between the cup and its substrate, and of insertion force, on the cups' primary stability. The results of our study show that primary stability depends on the surface roughness of the cup. The presence of macro-roughness on the peripheral ring is found to decrease primary stability; there was excessive abrasion of the substrate, damaging it and leading to poor primary stability. Numerical modeling indicates that oversizing the cup compared to its substrate has an impact on primary stability, as has insertion force. Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.

Risk to Water Security on Small Islands

NASA Astrophysics Data System (ADS)

Holding, S. T.; Allen, D. M.

2013-12-01

The majority of fresh water available on small islands is shallow groundwater that forms a freshwater lens. Freshwater lenses are generally limited in extent and as such are vulnerable to many stressors that impact water security. These include stressors related to climate change, such as sea level rise, as well as those related to human impacts, such as contamination. Traditionally, water security assessments have focussed on indicators that provide a snapshot of the current condition. However, recent work suggests that in order to effectively manage the water system, it is also important to consider uncertain future impacts to the system by evaluating how different stressors might impact water security. In this study, a framework for assessing risk to water security was developed and tested on Andros Island in The Bahamas. The assessment comprises two main components that characterise the water system: numerical modelling studies and a hazard survey. A baseline numerical model of the freshwater lens throughout Andros Island was developed to simulate the morphology of the freshwater lens and estimate the freshwater resources currently available. The model was prepared using SEAWAT, a density-dependent flow and solute transport code. Various stressors were simulated in the model to evaluate the response of the freshwater lens to predicted future shifts in climate patterns, sea level rise, and changes in water use. A hazard survey was also conducted on the island to collect information related to the storage of contaminants, sanitation infrastructure, waste disposal practices and groundwater abstraction rates. The results of the survey form a geo-spatial database of the location and associated hazards to the freshwater lens. The resulting risk framework provides a ranking of overall risk to water security based on information from the numerical modelling and hazard survey. The risk framework is implemented in a Geographic Information System (GIS) and provides a map of the risk to water security throughout Andros Island. It evaluates risk to water security for current and future scenarios and will enable water resource managers to effectively adapt to future impacts on water security.

Impacts of moving bottlenecks on traffic flow

NASA Astrophysics Data System (ADS)

Ou, Hui; Tang, Tie-Qiao

2018-06-01

Bottleneck (especially the moving bottleneck) widely exists in the urban traffic system. However, little effort has been made to study the impacts of the moving bottleneck on traffic flow (especially the evolution and propagation of traffic flow). In this article, we introduce the speed of a moving bottleneck into a traffic flow model, then propose an extended macro traffic flow with a moving bottleneck, and finally use the proposed model to study the effects of a moving bottleneck on the evolution and propagation of traffic flow under uniform flow and a small perturbation. The numerical results indicate that the moving bottleneck has prominent influences on the evolution of traffic flow under the two typical traffic situations and that the impacts are dependent on the initial density.

WWC Review of the Report "The Effects of Math Video Games on Learning." What Works Clearinghouse Single Study Review

ERIC Educational Resources Information Center

What Works Clearinghouse, 2015

2015-01-01

In the 2014 study, "The Effects of Math Video Games on Learning," researchers examined the impacts of math video games on the fractions knowledge of 1,468 sixth-grade students in 23 schools. The video games focused on fractions concepts including: whole units, numerator and denominator, understanding the number line, fractions…

An Analysis of High Impact Scholarship and Publication Trends in Blended Learning

ERIC Educational Resources Information Center

Halverson, Lisa R.; Graham, Charles R.; Spring, Kristian J.; Drysdale, Jeffery S.

2012-01-01

Blended learning is a diverse and expanding area of design and inquiry that combines face-to-face and online modalities. As blended learning research matures, numerous voices enter the conversation. This study begins the search for the center of this emerging area of study by finding the most cited scholarship on blended learning. Using Harzing's…

Impact of Profiling Technologies in the Understanding of Recombinant Protein Production

NASA Astrophysics Data System (ADS)

Vijayendran, Chandran; Flaschel, Erwin

Since expression profiling methods have been available in a high throughput fashion, the implication of these technologies in the field of biotechnology has increased dramatically. Microarray technology is one such unique and efficient methodology for simultaneous exploration of expression levels of numerous genes. Likewise, two-dimensional gel electrophoresis or multidimensional liquid chromatography coupled with mass spectrometry are extensively utilised for studying expression levels of numerous proteins. In the field of biotechnology these highly parallel analytical methods have paved the way to study and understand various biological phenomena depending on expression patterns. The next phenomenological level is represented by the metabolome and the (metabolic) fluxome. However, this chapter reviews gene and protein profiling and their impact on understanding recombinant protein production. We focus on the computational methods utilised for the analyses of data obtained from these profiling technologies as well as prominent results focusing on recombinant protein expression with Escherichia coli. Owing to the knowledge accumulated with respect to cellular signals triggered during recombinant protein production, this field is on the way to design strategies for developing improved processes. Both gene and protein profiling have exhibited a handful of functional categories to concentrate on in order to identify target genes and proteins, respectively, involved in the signalling network with major impact on recombinant protein production.

Impact tensile properties and strength development mechanism of glass for reinforcement fiber

NASA Astrophysics Data System (ADS)

Kim, T.; Oshima, K.; Kawada, H.

2013-07-01

In this study, impact tensile properties of E-glass were investigated by fiber bundle testing under a high strain rate. The impact tests were performed employing two types of experiments. One is the tension-type split Hopkinson pressure bar system, and the other is the universal high-speed tensile-testing machine. As the results, it was found that not only the tensile strength but also the fracture strain of E-glass fiber improved with the strain rate. The absorbed strain energy of this material significantly increased. It was also found that the degree of the strain rate dependency of E-glass fibers on the tensile strength was varied according to fiber diameter. As for the strain rate dependency of the glass fiber under tensile loading condition, change of the small crack-propagation behaviour was considered to clarify the development of the fiber strength. The tensile fiber strength was estimated by employing the numerical simulation based on the slow crack-growth model (SCG). Through the parametric study against the coefficient of the crack propagation rate, the numerical estimation value was obtained for the various testing conditions. It was concluded that the slow crack-growth behaviour in the glass fiber was an essential for the increase in the strength of this material.

Radiative flow of Carreau liquid in presence of Newtonian heating and chemical reaction

NASA Astrophysics Data System (ADS)

Hayat, T.; Ullah, Ikram; Ahmad, B.; Alsaedi, A.

Objective of this article is to investigate the magnetohydrodynamic (MHD) boundary layer stretched flow of Carreau fluid in the presence of Newtonian heating. Sheet is presumed permeable. Analysis is studied in the presence of chemical reaction and thermal radiation. Mathematical formulation is established by using the boundary layer approximations. The resultant nonlinear flow analysis is computed for the convergent solutions. Interval of convergence via numerical data and plots are obtained and verified. Impact of numerous pertinent variables on the velocity, temperature and concentration is outlined. Numerical data for surface drag coefficient, surface heat transfer (local Nusselt number) and mass transfer (local Sherwood number) is executed and inspected. Comparison of skin friction coefficient in limiting case is made for the verification of current derived solutions.

Numerical study for melting heat transfer and homogeneous-heterogeneous reactions in flow involving carbon nanotubes

NASA Astrophysics Data System (ADS)

Hayat, Tasawar; Muhammad, Khursheed; Alsaedi, Ahmed; Asghar, Saleem

2018-03-01

Present work concentrates on melting heat transfer in three-dimensional flow of nanofluid over an impermeable stretchable surface. Analysis is made in presence of porous medium and homogeneous-heterogeneous reactions. Single and multi-wall CNTs (carbon nanotubes) are considered. Water is chosen as basefluid. Adequate transformations yield the non-linear ordinary differential systems. Solution of emerging problems is obtained using shooting method. Impacts of influential variables on velocity and temperature are discussed graphically. Skin friction coefficient and Nusselt number are numerically discussed. The results for MWCNTs and SWCNTs are compared and examined.

Numerical simulation of droplet impact onto a solid sphere in mid-air

NASA Astrophysics Data System (ADS)

Banitabaei, Sayed Abdolhossein; Amirfazli, Alidad

2017-11-01

Collision of a droplet and a particle in mid-air has applications in chemical, petrochemical, and pharmaceutical industries. As a result of a head-on collision between a droplet and a hydrophobic particle with a relative diameter of a thin liquid film is created in the form of a hallow truncated cone (i.e. lamella). In this work, a numerical simulation was developed based on VOF method for head-on collision of a falling droplet and a moving particle. Impact outcomes predicted by the model shows a fair agreement with the experimental images of lamellas (Vp = 6.8 and Vd = 0.68 m/s). Using the simulation model, the effect of liquid viscosity and surface tension on impact outcomes were studied. As viscosity increases, the lamella thickness increases accordingly. This happens as more energy transfer is required to move the liquid layers against each other to create a longer, and therefore thinner, lamella. However, a small decrease in viscosity halts the lamella formation as the boundary layer thickness in the spreading liquid gets so small that a crown cannot be developed. Moreover, investigation of the effect of particle wettability on the impact outcomes indicates that a lamella only forms due to impact of a droplet onto a hydrophobic particle. The lamella geometry is not affected by the particle wettability after contact angle reaches a certain threshold. These results show a good agreement with the literature of drop impact on a stationary particle.

Numerical investigations on axial and radial blade rubs in turbo-machinery

NASA Astrophysics Data System (ADS)

Abdelrhman, Ahmed M.; Tang, Eric Sang Sung; Salman Leong, M.; Al-Qrimli, Haidar F.; Rajamohan, G.

2017-07-01

In the recent years, the clearance between the rotor blades and stator/casing had been getting smaller and smaller prior improving the aerodynamic efficiency of the turbomachines as demand in the engineering field. Due to the clearance reduction between the blade tip and the rotor casing and between rotor blades and stator blades, axial and radial blade rubbing could be occurred, especially at high speed resulting into complex nonlinear vibrations. The primary aim of this study is to address the blade axial rubbing phenomenon using numerical analysis of rotor system. A comparison between rubbing caused impacts of axial and radial blade rubbing and rubbing forces are also aims of this study. Tow rotor models (rotor-stator and rotor casing models) has been designed and sketched using SOILDSWORKS software. ANSYS software has been used for the simulation and the numerical analysis. The rubbing conditions were simulated at speed range of 1000rpm, 1500rpm and 2000rpm. Analysis results for axial blade rubbing showed the appearance of blade passing frequency and its multiple frequencies (lx, 2x 3x etc.) and these frequencies will more excited with increasing the rotational speed. Also, it has been observed that when the rotating speed increased, the rubbing force and the harmonics frequencies in x, y and z-direction become higher and severe. The comparison study showed that axial blade rub is more dangerous and would generate a higher vibration impacts and higher blade rubbing force than radial blade rub.

Life in the dark: Roots and how they regulate plant-soil interactions

NASA Astrophysics Data System (ADS)

Wu, Y.; Chou, C.; Peruzzo, L.; Riley, W. J.; Hao, Z.; Petrov, P.; Newman, G. A.; Versteeg, R.; Blancaflor, E.; Ma, X.; Dafflon, B.; Brodie, E.; Hubbard, S. S.

2017-12-01

Roots play a key role in regulating interactions between soil and plants, an important biosphere process critical for soil development and health, global food security, carbon sequestration, and the cycling of elements (water, carbon, nutrients, and environmental contaminants). However, their underground location has hindered studies of plant roots and the role they play in regulating plant-soil interactions. Technological limitations for root phenotyping and the lack of an integrated approach capable of linking root development, its environmental adaptation/modification with subsequent impact on plant health and productivity are major challenges faced by scientists as they seek to understand the plant's hidden half. To overcome these challenges, we combine novel experimental methods with numerical simulations, and conduct controlled studies to explore the dynamic growth of crop roots. We ask how roots adapt to and change the soil environment and their subsequent impacts on plant health and productivity. Specifically, our efforts are focused on (1) developing novel geophysical approaches for non-invasive plant root and rhizosphere characterization; (2) correlating root developments with key canopy traits indicative of plant health and productivity; (3) developing numerical algorithms for novel geophysical root signal processing; (4) establishing plant growth models to explore root-soil interactions and above and below ground traits co-variabilities; and (5) exploring how root development modifies rhizosphere physical, hydrological, and geochemical environments for adaptation and survival. Our preliminary results highlight the potential of using electro-geophysical methods to quantifying key rhizosphere traits, the capability of the ecosys model for mechanistic plant growth simulation and traits correlation exploration, and the combination of multi-physics and numerical approach for a systematic understanding of root growth dynamics, impacts on soil physicochemical environments, and plant health and productivity.

The Impact of Sea Surface Temperature on Organized Convective Storms Crossing over Coastlines

NASA Astrophysics Data System (ADS)

Lombardo, K.

2016-02-01

As organized coastal convective storms develop over land and move over the coastal ocean, their storm-scale structures, intensity, and associated weather threats evolve. This study aims to quantify the impact of sea surface temperature on the fundamental mechanisms controlling the evolution of coastal quasi-linear convective systems (QLCSs) as they move offshore. Results from this work will contribute to the improved predictability of these coastal, potentially severe warm season storms. The current work systematically studies the interaction between QLCSs and marine atmospheric boundary layers (MABLs) associated with the coastal ocean in an idealized numerical framework. The initial simulations are run in 2-dimensions, with a 250 m horizontal resolution and a vertical resolution ranging from 100 m in the lowest 3000 m stretched to 250 m at the top of the 20 km domain. To create a numerical environment representative of a coastal region, the western half of the 800 km domain is configured to represent a land surface, while the eastern half represents a water surface. A series of sensitivity experiments are conducted to explore the influence of sea surface temperature and the overlying MABL on coastal QLCSs. Sea surface temperature values are selected to represent values observed within the Mid-Atlantic Bight coastal waters, including 5oC (min SST - January), 14oC (early summer), and 23oC (late summer). The numerical MABL is allowed to develop through surface heat fluxes. Preliminary simulations indicate that SST influences storm structure, with the stratiform precipitation shield becoming progressively wider as SST increases. SST also impacts propagation speed; once the storms are over the water, the early and late summer QLCSs move more quickly than the min SST storm. The physical mechanisms contributing to these and other differences will be discussed.

Predicted and observed directional dependence of meteoroid/debris impacts on LDEF thermal blankets

NASA Astrophysics Data System (ADS)

Drolshagen, Gerhard

1992-06-01

The number of impacts from meteoroids and space debris particles to the various Long Duration Exposure Facility (LDEF) rows is calculated using ESABASE/DEBRIS, a 3-D numerical analysis tool. It is based on the latest environment flux models and includes geometrical and directional effects. A detailed comparison of model predictions and actual observations is made for impacts on the thermal blankets which covered the USCR experiment. Impact features on these blankets were studied intensively in European laboratories and hypervelocity impacts for calibration were performed. The thermal blankets were located on all LDEF rows, except 3, 9, and 12. Because of their uniform composition and thickness, these blankets allow a direct analysis of the directional dependence of impacts and provide a unique test case for the latest meteoroid and debris flux models.

The disposition of impact ejecta resulting from the AIDA-DART mission to binary asteroid 65803 Didymos: an independent investigation

NASA Astrophysics Data System (ADS)

Richardson, James E.; O'Brien, David P.

2016-10-01

If all goes as planned, in the year 2020 a joint ESA and NASA mission will be launched that will rendezvous with the near-Earth binary asteroid system 65803 Didymos in the fall of 2022. The European component, the Asteroid Impact & Deflection Assessment (AIDA) spacecraft will arrive first and characterize the system, which consists of a ~800 m diameter primary and a ~160 m diameter secondary, orbiting a common center of mass at a semi-major axis distance of ~1200 m with a orbital period of 11.9 hr. Following system characterization, the AIDA spacecraft will remove to a safe distance while the NASA component, the 300 kg Double Asteroid Redirection Test (DART) spacecraft collides with the trailing edge of the secondary body (with respect to the binary's retrograde mutual orbit). Meanwhile, the AIDA spacecraft will conduct observations of this impact and its aftermath, specifically looking for changes made to the primary, the secondary, and their mutual orbit as a result of the DART collision. Of particular interest is the ballistic flight and final disposition of the ejecta produced by the impact cratering process, not just from the standpoint of scientific study, but also from the standpoint of AIDA spacecraft safety.In this study, we investigate a series of hypothetical DART impacts utilizing a semi-empirical, numerical impact ejecta plume model originally developed for the Deep Impact mission and designed specifically with impacts on small bodies in mind. The resulting excavated mass is discretized into 7200 individual tracer particles, each representing a unique combination of speed, mass, and ejected direction. The trajectory of each tracer is computed numerically under the gravitational influence of both primary and secondary, along with the effects of solar radiation pressure. Each tracer is followed until it either impacts a body or escapes the system, whereupon tracking is continued in the heliocentric frame using an N-body integrator. Various impact scenarios will be explored, along with a number of ejecta particle sizes, with the aim of characterizing the most likely final ejecta dispositions resulting from the DART impact, and the safest vantages from which the AIDA spacecraft can observe this event.

Shock-induced damage in rocks: Application to impact cratering

NASA Astrophysics Data System (ADS)

Ai, Huirong

Shock-induced damage beneath impact craters is studied in this work. Two representative terrestrial rocks, San Marcos granite and Bedford limestone, are chosen as test target. Impacts into the rock targets with different combinations of projectile material, size, impact angle, and impact velocity are carried out at cm scale in the laboratory. Shock-induced damage and fracturing would cause large-scale compressional wave velocity reduction in the recovered target beneath the impact crater. The shock-induced damage is measured by mapping the compressional wave velocity reduction in the recovered target. A cm scale nondestructive tomography technique is developed for this purpose. This technique is proved to be effective in mapping the damage in San Marcos granite, and the inverted velocity profile is in very good agreement with the result from dicing method and cut open directly. Both compressional velocity and attenuation are measured in three orthogonal directions on cubes prepared from one granite target impacted by a lead bullet at 1200 m/s. Anisotropy is observed from both results, but the attenuation seems to be a more useful parameter than acoustic velocity in studying orientation of cracks. Our experiments indicate that the shock-induced damage is a function of impact conditions including projectile type and size, impact velocity, and target properties. Combined with other crater phenomena such as crater diameter, depth, ejecta, etc., shock-induced damage would be used as an important yet not well recognized constraint for impact history. The shock-induced damage is also calculated numerically to be compared with the experiments for a few representative shots. The Johnson-Holmquist strength and failure model, initially developed for ceramics, is applied to geological materials. Strength is a complicated function of pressure, strain, strain rate, and damage. The JH model, coupled with a crack softening model, is used to describe both the inelastic response of rocks in the compressive field near the impact source and the tensile failure in the far field. The model parameters are determined either from direct static measurements, or from indirect numerical adjustment. The agreement between the simulation and experiment is very encouraging.

Bottom-up and top-down attentional contributions to the size congruity effect.

PubMed

Sobel, Kenith V; Puri, Amrita M; Faulkenberry, Thomas J

2016-07-01

The size congruity effect refers to the interaction between the numerical and physical (i.e., font) sizes of digits in a numerical (or physical) magnitude selection task. Although various accounts of the size congruity effect have attributed this interaction to either an early representational stage or a late decision stage, only Risko, Maloney, and Fugelsang (Attention, Perception, & Psychophysics, 75, 1137-1147, 2013) have asserted a central role for attention. In the present study, we used a visual search paradigm to further study the role of attention in the size congruity effect. In Experiments 1 and 2, we showed that manipulating top-down attention (via the task instructions) had a significant impact on the size congruity effect. The interaction between numerical and physical size was larger for numerical size comparison (Exp. 1) than for physical size comparison (Exp. 2). In the remaining experiments, we boosted the feature salience by using a unique target color (Exp. 3) or by increasing the display density by using three-digit numerals (Exps. 4 and 5). As expected, a color singleton target abolished the size congruity effect. Searching for three-digit targets based on numerical size (Exp. 4) resulted in a large size congruity effect, but search based on physical size (Exp. 5) abolished the effect. Our results reveal a substantial role for top-down attention in the size congruity effect, which we interpreted as support for a shared-decision account.

Service impact of a national clinical leadership development programme: findings from a qualitative study.

PubMed

Fealy, Gerard M; McNamara, Martin S; Casey, Mary; O'Connor, Tom; Patton, Declan; Doyle, Louise; Quinlan, Christina

2015-04-01

The study reported here was part of a larger study, which evaluated a national clinical leadership development programme with reference to resources, participant experiences, participant outcomes and service impact. The aim of the present study was to evaluate the programme's service impact. Clinical leadership development develops competencies that are expressed in context. The outcomes of clinical leadership development occur at individual, departmental and organisational levels. The methods used to evaluate the service impact were focus groups, group interviews and individual interviews. Seventy participants provided data in 18 separate qualitative data collection events. The data contained numerous accounts of service development activities, initiated by programme participants, which improved service and/or improved the culture of the work setting. Clinical leadership development programmes that incorporate a deliberate service impact element can result in identifiable positive service outcomes. The nuanced relationship between leader development and service development warrants further investigation. This study demonstrates that clinical leadership development can impact on service in distinct and identifiable ways. Clinical leadership development programmes should focus on the setting in which the leadership competencies will be demonstrated. © 2013 John Wiley & Sons Ltd.

Wintertime component of the THORPEX Pacific-Asian Regional Campaign (T-PARC)

NASA Astrophysics Data System (ADS)

Song, Y.; Toth, Z.; Asuma, Y.; Reynolds, C.; Lngland, R.; Szunyogh, I.; Colle, B.; Chang, E.; Doyle, C.; Kats, A.

2009-04-01

The winter component of the T-PARC is an international field project that aims at improving high impact weather event forecasts for North America. The main objective is to understand how perturbations from the tropics, Eurasia and polar fronts travel through waveguide and turn into high impact weather events. Through adaptive observations by using manned aircrafts (NOAA G-IV and US Air force C-130s) and Russian rawinsonde network over data sparse regions, it is expected that accurate initial conditions will improve the numerical weather forecasts. Non-adaptive aircraft measurements over the Pacific Rim and part of India are also deployed through E-AMDAR program, which is expected to improve the background field over Asia where perturbations are initiated. The campaign is led by NOAA and joined by agencies and universities from US, Canada, Mexico, Japan, ECWMF, and Russia. While most observational data will be assimilated by operational centers to improve real time numerical weather predictions, post field studies will focus on aspects such as: data impact on forecast and analysis, dry and moist processes that affect the formation and propagation of perturbations, meso-scale storm structure, error growth, forecast "busts" under certain atmospheric regimes, and socio-economic applications such as costs and benefits of improved forecasts and their use by the public for high impact weather events. In particular, a Winter Olympics demonstration project (February 12 - February 28) is expected to be a test bed during winter T-PARC for real user outreach and application purposes. Effectiveness of existing targeting methods as well as new targeting methods in the 3-5 day lead time range will be pursued and other aspects related to data assimilation and numerical forecasts (both deterministic and ensemble forecasts) will be investigated within this project as well.

Numerical model of solar dynamic radiator for parametric analysis

NASA Technical Reports Server (NTRS)

Rhatigan, Jennifer L.

1989-01-01

Growth power requirements for Space Station Freedom will be met through addition of 25 kW solar dynamic (SD) power modules. The SD module rejects waste heat from the power conversion cycle to space through a pumped-loop, multi-panel, deployable radiator. The baseline radiator configuration was defined during the Space Station conceptual design phase and is a function of the state point and heat rejection requirements of the power conversion unit. Requirements determined by the overall station design such as mass, system redundancy, micrometeoroid and space debris impact survivability, launch packaging, costs, and thermal and structural interaction with other station components have also been design drivers for the radiator configuration. Extensive thermal and power cycle modeling capabilities have been developed which are powerful tools in Station design and analysis, but which prove cumbersome and costly for simple component preliminary design studies. In order to aid in refining the SD radiator to the mature design stage, a simple and flexible numerical model was developed. The model simulates heat transfer and fluid flow performance of the radiator and calculates area mass and impact survivability for many combinations of flow tube and panel configurations, fluid and material properties, and environmental and cycle variations. A brief description and discussion of the numerical model, it's capabilities and limitations, and results of the parametric studies performed is presented.

Dynamics of anchor last deployment of submersible buoy system

NASA Astrophysics Data System (ADS)

Zheng, Zhongqiang; Xu, Jianpeng; Huang, Peng; Wang, Lei; Yang, Xiaoguang; Chang, Zongyu

2016-02-01

Submersible buoy systems are widely used for oceanographic research, ocean engineering and coastal defense. Severe sea environment has obvious effects on the dynamics of submersible buoy systems. Huge tension can occur and may cause the snap of cables, especially during the deployment period. This paper studies the deployment dynamics of submersible buoy systems with numerical and experimental methods. By applying the lumped mass approach, a three-dimensional multi-body model of submersible buoy system is developed considering the hydrodynamic force, tension force and impact force between components of submersible buoy system and seabed. Numerical integration method is used to solve the differential equations. The simulation output includes tension force, trajectory, profile and dropping location and impact force of submersible buoys. In addition, the deployment experiment of a simplified submersible buoy model was carried out. The profile and different nodes' velocities of the submersible buoy are obtained. By comparing the results of the two methods, it is found that the numerical model well simulates the actual process and conditions of the experiment. The simulation results agree well with the results of the experiment such as gravity anchor's location and velocities of different nodes of the submersible buoy. The study results will help to understand the conditions of submersible buoy's deployment, operation and recovery, and can be used to guide the design and optimization of the system.

Investigations of primary and secondary impact structures on the moon and laboratory experiments to study the ejecta of secondary particles. Ph.D. Thesis - Ruprecht Karl Univ.

NASA Technical Reports Server (NTRS)

Koenig, B.

1977-01-01

Young lunar impact structures were investigated by using lunar orbiter, Apollo Metric and panorama photographs. Measurements on particularly homogeneous areas low in secondary craters made possible an expansion of primary crater distribution to small diameters. This is now sure for a range between 20m or = D or = 20km and this indicates that the size and velocity distribution of the impacting bodies in the last 3 billion years has been constant. A numerical approximation in the form of a 7th degree polynomial was obtained for the distribution.

Crush analysis of the foam-filled bitubal circular tube under oblique impact

NASA Astrophysics Data System (ADS)

Djamaluddin, F.; Abdullah, S.; Arrifin, A. K.; Nopiah, Z. M.

2018-02-01

This paper presents crashworthiness analysis of bitubal cylindrical tubes under different impact angular. The numerical solution of double cylindrical tubes are determined by finite element analysis (FEA). Moreover, the structure was impacted by mass block as impactor respect to longitudinal direction of the tubes. The model of structure was developed by non-linear ABAQUS sofware with variations of load angle and dimensions of tube. The outcome of this study is the respons parameters such as the peak crusing force (PCF), energy absorption (EA) and specific energy absorption (SEA), thus it can be expected this tube as the great energy absorber.

The Chelyabinsk meteor

NASA Astrophysics Data System (ADS)

Popova, O.; Jenniskens, P.; Shuvalov, V.; Emel'yanenko, V.; Rybnov, Y.; Kharlamov, V.; Kartashova, A.; Biryukov, E.; Khaibrakhmanov, S.

2014-07-01

A review is given about what was learned about the 0.5-Mt Chelyabinsk airburst of 15 February 2013 by field studies, the analysis of recovered meteorites, and numerical models of meteoroid fragmentation and airburst propagation. Previous events with comparable or larger energy in recent times include only the 0.5-Mt -sized 3 August 1963 meteor over the south Atlantic, for which only an infrasound signal was recorded, and the famous Tunguska impact of 1908. Estimates of the initial kinetic energy of the Tunguska impact range from 3 to 50 Mt, due to the lack of good observations at the time. The Chelyabinsk event is much better documented than both, and provides a unique opportunity to calibrate the different approaches used to model meteoroid entry and calculate the damaging effects of a shock wave from a large meteoroid impact. A better understanding of what happened might help future impact hazard mitigation efforts by calibrating models of what might happen under somewhat different circumstances. The initial kinetic energy is estimated from infrasonic signals and the fireball's lightcurve, as well as the extent of the glass damage on the ground. Analysis of video observations of the fireball and the shadow movements provided an impact trajectory and a record of the meteor lightcurve, which describes how that energy was deposited in the atmosphere. Ablation and fragmentation scenarios determine the success of attempts to reproduce the observed meteor lightcurve and deceleration profile by numerical modeling. There was almost no deceleration until peak brightness. Meteoroid fragmentation occurred in different forms, some part of the initial mass broke in well separated fragments, the surviving fragments falling on the ground as meteorites. The specific conditions during energy deposition determined the fraction of surviving mass. The extent of the glass damage was mapped by visiting over 50 villages in the area. A number of numerical simulations were conducted that attempted a more realistic release of energy along the trajectory and these results were compared with observations of blast wave arrival times and the extent of the glass damage. The shape of the damaged area could be explained from the fact that the energy was deposited over a range of altitudes. The study of the recovered meteorites provided insight into why the Chelyabinsk meteoroid broke at a relatively high altitude. Its material properties were determined by events that may date back to the Earth-Moon impact event.

Numerical Investigation of Rockfall Impacts on Muckpiles for Underground Portals

NASA Astrophysics Data System (ADS)

Effeindzourou, Anna; Giacomini, Anna; Thoeni, Klaus; Sloan, Scott W.

2017-06-01

Small-scale waste rock piles or muckpiles are commonly used as energy absorption barriers in various surface mining applications. This paper numerically investigates the impact behaviour of blocks on muckpiles used as cushion layer on top of underground portal entries. A three-dimensional discrete element model is implemented into the open-source framework YADE and validated using full-scale experimental data. The model allows estimating the energy absorption capacity of the muckpile and the impact forces acting on the portal structure. It also provides valuable information on the rebound characteristics which are useful for the definition of the potential safety areas in the vicinity of an underground entry. In order to show its capabilities, the model is applied to a large number of cases representing potential design conditions. The influence of block mass, impact velocity and absorbing cushion thickness on the forces at the base of the muckpile and the rebound trajectories after impact are investigated.

Experimental and Numerical Study of Wind and Turbulence in a Near-Field Dispersion Campaign at an Inhomogeneous Site

NASA Astrophysics Data System (ADS)

Wei, Xiao; Dupont, Eric; Gilbert, Eric; Musson-Genon, Luc; Carissimo, Bertrand

2016-09-01

We present a detailed experimental and numerical study of the local flow field for a pollutant dispersion experimental program conducted at SIRTA (Site Instrumental de Recherche par Télédétection Atmosphérique), a complex and intensively instrumented site in a southern suburb of Paris. Global analysis of continuous measurements over 2 years highlights the impact of terrain heterogeneity on wind and turbulence. It shows that the forest to the north of the experimental field induces strong directional shear and wind deceleration below the forest canopy height. This directional shear is stronger with decreasing height and decreasing distance from the forest edge. Numerical simulations are carried out using Code_Saturne, a computational fluid dynamics code, in Reynolds-averaged Navier-Stokes mode with a standard k{-}ɛ closure and a canopy model, in neutral and stable stratifications. These simulations are shown to reproduce globally well the characteristics of the mean flow, especially the directional wind shear in northeasterly and northwesterly cases and the turbulent kinetic energy increase induced by the forest. However, they slightly underestimate wind speed and the directional shear of the flow below the forest canopy height. Sensitivity studies are performed to investigate the influence of leaf area density, inlet stability condition, and roughness length. These studies show that the typical features of the canopy flow become more pronounced as canopy density increases. Performance statistics indicate that the impact of the forest and adequate inlet profiles are the most important factors in the accurate reproduction of flow at the site, especially under stable stratification.

Local and remote climatic impacts due to land use degradation in the Amazon "Arc of Deforestation"

NASA Astrophysics Data System (ADS)

Silva, Maria Elisa Siqueira; Pereira, Gabriel; da Rocha, Rosmeri Porfírio

2016-08-01

Many numerical studies, among them, global and regional models, have been used to simulate climatic impact due to Amazon deforestation. Most of them did not consider deforestation as usually observed and the induced dynamic changes. The present study explores the physical impacts due to Amazon deforestation by considering local and remote changes in the circulation and thermodynamics. For this, numerical experiments were conducted with RegCM3 using a relatively fine horizontal grid spacing (50 km), more realistic deforested areas (similar to the highway-network-shaped), and an updated land use map. The studied period was 2001-2006 October-March. As in most previous studies focusing on Amazon deforestation, the RegCM3-simulated air temperature increases over degraded areas, ranging from 1.0 to 2.5 °C, and precipitation decreases of around 10 %. This result is mainly related to depletion in evapotranspiration rates provided by lesser soil water extraction by the degraded vegetation. The weakening of upward motion in the mid-upper troposphere is an associated mechanism that explains the precipitation decrease after Amazon deforestation. A new result is the simulated precipitation increase, about 10 %, over the eastern South America and the adjacent South Atlantic Ocean. In these areas, the precipitation increase during October-March is associated with intensification of upper-level high pressure (the Bolivian high) coupled with negative geopotential height anomalies southeastward of the center of the high.

Characterising the effect of global and local geometric imperfections on the numerical performance of a brace member

NASA Astrophysics Data System (ADS)

Hassan, M. S.; Goggins, J.; Salawdeh, S.

2015-07-01

A numerical imperfection study is carried out on a hot rolled tubular brace member under displacement controlled amplitudes. An appropriate range of global and local imperfections is used in the finite element analyses to evaluate the initial-post buckling compressive strength, lateral storey drift, energy dissipation and mid-length lateral deformation of the brace member. The purpose of this study is to assess the impact of the geometrical imperfection on the numerical performance, and to determine an amplitude range that can be used unequivocally for numerical modelling of brace members. It is shown that the amplitude of global imperfections has an effect on the initial response, whereas the amplitude of local imperfections has influence on the resistance capacity of the brace member at higher ductility level. Based on the results, a refined range of amplitude of global and local imperfections is proposed. This range is found to have a good agreement with design standards. In addition, an already established equation to find lateral deformation is compared to results from the analyses and found that the equation with some modification can be used accurately in design. In this paper, a modification factor is proposed in the equation to find the lateral deformation to account for the imperfection amplitude in the numerical analyses of brace members.

Particle Bonding Mechanism in Cold Gas Dynamic Spray: A Three-Dimensional Approach

NASA Astrophysics Data System (ADS)

Zhu, Lin; Jen, Tien-Chien; Pan, Yen-Ting; Chen, Hong-Sheng

2017-12-01

Cold gas dynamic spray (CGDS) is a surface coating process that uses highly accelerated particles to form the surface coating. In the CGDS process, metal particles with a diameter of 1-50 µm are carried by a gas stream at high pressure (typically 20-30 atm) through a de Laval-type nozzle to achieve supersonic velocity upon impact onto the substrate. Typically, the impact velocity ranges between 300 and 1200 m/s in the CGDS process. When the particle is accelerated to its critical velocity, which is defined as the minimum in-flight velocity at which it can deposit on the substrate, adiabatic shear instabilities will occur. Herein, to ascertain the critical velocities of different particle sizes on the bonding efficiency in CGDS process, three-dimensional numerical simulations of single particle deposition process were performed. In the CGDS process, one of the most important parameters which determine the bonding strength with the substrate is particle impact temperature. It is hypothesized that the particle will bond to the substrate when the particle's impacting velocity surpasses the critical velocity, at which the interface can achieve 60% of the melting temperature of the particle material (Ref 1, 2). Therefore, critical velocity should be a main parameter on the coating quality. Note that the particle critical velocity is determined not only by its size, but also by its material properties. This study numerically investigates the critical velocity for the particle deposition process in CGDS. In the present numerical analysis, copper (Cu) was chosen as particle material and aluminum (Al) as substrate material. The impacting velocities were selected between 300 and 800 m/s increasing in steps of 100 m/s. The simulation result reveals temporal and spatial interfacial temperature distribution and deformation between particle(s) and substrate. Finally, a comparison is carried out between the computed results and experimental data.

Simulated Climate Impacts of Mexico City's Historical Urban Expansion

NASA Astrophysics Data System (ADS)

Benson-Lira, Valeria

Urbanization, a direct consequence of land use and land cover change, is responsible for significant modification of local to regional scale climates. It is projected that the greatest urban growth of this century will occur in urban areas in the developing world. In addition, there is a significant research gap in emerging nations concerning this topic. Thus, this research focuses on the assessment of climate impacts related to urbanization on the largest metropolitan area in Latin America: Mexico City. Numerical simulations using a state-of-the-science regional climate model are utilized to address a trio of scientifically relevant questions with wide global applicability. The importance of an accurate representation of land use and land cover is first demonstrated through comparison of numerical simulations against observations. Second, the simulated effect of anthropogenic heating is quantified. Lastly, numerical simulations are performed using pre-historic scenarios of land use and land cover to examine and quantify the impact of Mexico City's urban expansion and changes in surface water features on its regional climate.

Annual Research Briefs: 1995

NASA Technical Reports Server (NTRS)

1995-01-01

This report contains the 1995 annual progress reports of the Research Fellows and students of the Center for Turbulence Research (CTR). In 1995 CTR continued its concentration on the development and application of large-eddy simulation to complex flows, development of novel modeling concepts for engineering computations in the Reynolds averaged framework, and turbulent combustion. In large-eddy simulation, a number of numerical and experimental issues have surfaced which are being addressed. The first group of reports in this volume are on large-eddy simulation. A key finding in this area was the revelation of possibly significant numerical errors that may overwhelm the effects of the subgrid-scale model. We also commissioned a new experiment to support the LES validation studies. The remaining articles in this report are concerned with Reynolds averaged modeling, studies of turbulence physics and flow generated sound, combustion, and simulation techniques. Fundamental studies of turbulent combustion using direct numerical simulations which started at CTR will continue to be emphasized. These studies and their counterparts carried out during the summer programs have had a noticeable impact on combustion research world wide.

A numerical investigation of factors affecting cervical spine injuries during rollover crashes.

PubMed

Hu, Jingwen; Yang, King H; Chou, Clifford C; King, Albert I

2008-11-01

Factors affecting the risk of cervical spine injury in rollover crashes were investigated using a detailed finite element human head-neck model. Analyze systematically neck responses and associated injury predictors under complex loading conditions similar to real-world rollover scenarios and use the findings to identify potential design improvements. Although many previous experimental and numerical studies have focused on cervical spine injury mechanisms and tolerance, none of them have investigated the risk of cervical spine injuries under loading condition similar to that in rollovers. The effects of changing the coefficient of friction (COF), impact velocity, padding material thickness and stiffness, and muscle force on the risk of neck injuries were analyzed in 16 different impact orientations based on a Taguchi array of design of experiments. Impact velocity is the most important factor in determining the risk of cervical spine fracture (P = 0.000). Decreases in the COF between the head and impact surface can effectively reduce the risk of cervical spine fracture (P = 0.038). If the COF is not 0, an impact with lateral force component could sometimes increase the risk of cervical spine fracture; and the larger the oriented angle of the impact surface, the more important it becomes to reduce the COF to protect the neck. Soft (P = 0.033) and thick (P = 0.137) padding can actually decrease the neck fracture risk, which is in contrast to previous experimental data. A careful selection of proper padding stiffness and thickness, along with a minimized COF between the head and impact surface or between the padding and its supporting structure, may simultaneously decrease the risk of head and neck injuries during rollover crashes. A seatbelt design to effectively reduce/eliminate the head-to-roof impact velocity is also very crucial to enhance the neck protection in rollovers.

School Climate, Connectedness and Academic Achievement: Examining Positive Impacts from High School Mentoring Services

ERIC Educational Resources Information Center

Angus, Rebecca; Hughes, Thomas

2017-01-01

Schools regularly implement numerous programs to satisfy widespread expectations. Often, implementation is carried out with little follow-up examining data that could help refine or determine the ultimate worth of the intervention. Through utilization of both descriptive and empirical methods, this study delved into the long-term effectiveness of…

Random Assignment and Informed Consent: A Case Study of Multiple Perspectives

ERIC Educational Resources Information Center

Walker, Robert; Hoggart, Lesley; Hamilton, Gayle

2008-01-01

Although random assignment is generally the preferred methodology in impact evaluations, it raises numerous ethical concerns, some of which are addressed by securing participants' informed consent. However, there has been little investigation of how consent is obtained in social experiments and the amount of information that can be conveyed--and…

Urban Green Space and Its Impact on Human Health

Treesearch

Michelle Kondo; Jaime Fluehr; Thomas McKeon; Charles Branas

2018-01-01

Background: Over half of the world's population now lives in urban areas, and this proportion is expected to increase. While there have been numerous reviews of empirical studies on the link between nature and human health, very few have focused on the urban context, and most have examined almost exclusively cross-sectional research. This...

Classroom Learning and Achievement: How the Complexity of Classroom Interaction Impacts Students' Learning

ERIC Educational Resources Information Center

Podschuweit, Sören; Bernholt, Sascha; Brückmann, Maja

2016-01-01

Background: Complexity models have provided a suitable framework in various domains to assess students' educational achievement. Complexity is often used as the analytical focus when regarding learning outcomes, i.e. when analyzing written tests or problem-centered interviews. Numerous studies reveal negative correlations between the complexity of…

Dynamic loading and release in Johnson Space Center Lunar regolith simulant

NASA Astrophysics Data System (ADS)

Plesko, C. S.; Jensen, B. J.; Wescott, B. L.; Skinner McKee, T. E.

2011-10-01

The behavior of regolith under dynamic loading is important for the study of planetary evolution, impact cratering, and other topics. Here we present the initial results of explosively driven flier plate experiments and numerical models of compaction and release in samples of the JSC-1A Lunar regolith simulant.

Landscape dynamics of mountain pine beetles

Treesearch

John E. Lundquist; Robin M. Reich

2014-01-01

The magnitude and urgency of current mountain pine beetle outbreaks in the western United States and Canada have resulted in numerous studies of the dynamics and impacts of these insects in forested ecosystems. This paper reviews some of the aspects of the spatial dynamics and landscape ecology of this bark beetle. Landscape heterogeneity influences dispersal patterns...

Effect of Sunlight on the Divergence of Community Structure of Fecal Bacteria in Cowpats Collected from Three Different Farms

EPA Science Inventory

Fecal pollution of environmental waters is a major concern for the general public because exposure to fecal-associated pathogens can have severe impacts on human health. In the last few years, numerous metagenomic studies applied next generation sequencing to understand the shift...

Cratering mechanics

NASA Technical Reports Server (NTRS)

Ivanov, B. A.

1986-01-01

Main concepts and theoretical models which are used for studying the mechanics of cratering are discussed. Numerical two-dimensional calculations are made of explosions near a surface and high-speed impact. Models are given for the motion of a medium during cratering. Data from laboratory modeling are given. The effect of gravitational force and scales of cratering phenomena is analyzed.

A Decade Revisited and a Step toward the Future: Incremental but Quintessential Progress

ERIC Educational Resources Information Center

Jin, D.-S.; Kim, M. H.; Park, D.

2014-01-01

This study scrutinizes "Asia Pacific Education Review" ("APER") that has been weathered 13 years of journey from its inception. Numerically, 504 peer-reviewed articles have been published so far, and 0.5 of impact factor has been achieved. This article recollects the history of "APER," overhaul the accomplishment and…

The Impact of Motivation on English Language Learning in the Gulf States

ERIC Educational Resources Information Center

Al Othman, Fadel H. M.; Shuqair, Khaled M.

2013-01-01

Numerous studies have shown that motivation is positively linked to success in learning the English language or any other second language. Generally, motivation and attitude work together to ensure learners' successful acquisition of a second language; hence, various motivational theories and models have been formulated to examine and explain this…

The Impact of Weight Perception on the Health Behaviors of College Students

ERIC Educational Resources Information Center

Osborn, Jessica; Naquin, Mildred; Gillan, Wynn; Bowers, Ashley

2016-01-01

Background: Obesity has links to numerous health problems. Having an accurate perception of one's own weight is an important aspect of maintaining an appropriate weight. Purpose: The purpose of this study was to examine relationships among perceived body weight, actual body weight, body satisfaction, and selected health behaviors. Methods: The…

The Impact of Centralization on Local School District Governance in Canada

ERIC Educational Resources Information Center

Galway, Gerald; Sheppard, Bruce; Wiens, John; Brown, Jean

2013-01-01

Across Canada there have been numerous recent examples of incidents where the political and ideological interests of provincial governments have run counter to the mandates of school districts. In this pan-Canadian study, focus groups were conducted with school board trustees and school district superintendents to examine the relationships between…

Side Walks in Education. NIACE Studies in the Human Career No. 14.

ERIC Educational Resources Information Center

Gerber, Alex, Jr.

A dark side of modernization parallels the numerous and obvious positive social impacts. Current social, political, economic, and ecological plights have been viewed as manifestations of a broader cultural crisis caused by adherence to a "reductionist" approach to reality. Reality, indeed, can only be understood in terms of process and…

Doomed to Read in a Second Language: Implications for Learning

ERIC Educational Resources Information Center

Miller, Paul; Peleg, Ora

2010-01-01

The aim of the study was to elucidate whether and how reliance on a second language impacts the learning of new information under very basic learning conditions. The paradigm used to investigate this issue required individuals to learn a series of associations between numerals and particular letter strings. Participants were two groups of…

The Burden of Stigma on Health and Well-Being: A Taxonomy of Concealment, Course, Disruptiveness, Aesthetics, Origin, and Peril Across 93 Stigmas.

PubMed

Pachankis, John E; Hatzenbuehler, Mark L; Wang, Katie; Burton, Charles L; Crawford, Forrest W; Phelan, Jo C; Link, Bruce G

2018-04-01

Most individuals are stigmatized at some point. However, research often examines stigmas separately, thus underestimating the overall impact of stigma and precluding comparisons across stigmatized identities and conditions. In their classic text, Social Stigma: The Psychology of Marked Relationships, Edward Jones and colleagues laid the groundwork for unifying the study of different stigmas by considering the shared dimensional features of stigmas: aesthetics, concealability, course, disruptiveness, origin, peril. Despite the prominence of this framework, no study has documented the extent to which stigmas differ along these dimensions, and the implications of this variation for health and well-being. We reinvigorated this framework to spur a comprehensive account of stigma's impact by classifying 93 stigmas along these dimensions. With the input of expert and general public raters, we then located these stigmas in a six-dimensional space and created discrete clusters organized around these dimensions. Next, we linked this taxonomy to health and stigma-related mechanisms. This quantitative taxonomy offers parsimonious insights into the relationship among the numerous qualities of numerous stigmas and health.

Numerical Simulation and Scaling Analysis of Cell Printing

NASA Astrophysics Data System (ADS)

Qiao, Rui; He, Ping

2011-11-01

Cell printing, i.e., printing three dimensional (3D) structures of cells held in a tissue matrix, is gaining significant attention in the biomedical community. The key idea is to use inkjet printer or similar devices to print cells into 3D patterns with a resolution comparable to the size of mammalian cells. Achieving such a resolution in vitro can lead to breakthroughs in areas such as organ transplantation. Although the feasibility of cell printing has been demonstrated recently, the printing resolution and cell viability remain to be improved. Here we investigate a unit operation in cell printing, namely, the impact of a cell-laden droplet into a pool of highly viscous liquids. The droplet and cell dynamics are quantified using both direct numerical simulation and scaling analysis. These studies indicate that although cell experienced significant stress during droplet impact, the duration of such stress is very short, which helps explain why many cells can survive the cell printing process. These studies also revealed that cell membrane can be temporarily ruptured during cell printing, which is supported by indirect experimental evidence.

Including a range of outcome targets offers a broader view of fibromyalgia treatment outcome: results from a retrospective review of multidisciplinary treatment.

PubMed

Marcus, Dawn A; Bernstein, Cheryl D; Haq, Adeel; Breuer, Paula

2014-06-01

Fibromyalgia is associated with substantial functional disability. Current drug and non-drug treatments result in statistically significant but numerically small improvements in typical numeric measures of pain severity and fibromyalgia impact. The aim of the present study was to evaluate additional measures of pain severity and functional outcome that might be affected by fibromyalgia treatment. This retrospective review evaluated outcomes from 274 adults with fibromyalgia who participated in a six-week, multidisciplinary treatment programme. Pain and function were evaluated on the first and final treatment visit. Pain was evaluated using an 11-point numerical scale to determine clinically meaningful pain reduction (decrease ≥ 2 points) and from a pain drawing. Function was evaluated by measuring active range of motion (ROM), walking distance and speed, upper extremity exercise repetitions, and self-reports of daily activities. Numerical rating scores for pain decreased by 10-13% (p < 0.01) and Fibromyalgia Impact Questionnaire (FIQ) scores decreased by 20% (p < 0.001). More substantial improvements were noted when using alternative measures. Clinically meaningful pain relief was achieved by 37% of patients, and the body area affected by pain decreased by 31%. ROM showed significant improvements in straight leg raise and cervical motion, without improvements in lumbar ROM. Daily walking distance increased fourfold and arm exercise repetitions doubled. Despite modest albeit statistically significant improvements in standard measures of pain severity and the FIQ, more substantial pain improvement was noted when utilizing alternative measures of pain and functional improvement. Alternative symptom assessment measures might be important outcome measures to include in drug and non-drug studies to better understand fibromyalgia treatment effectiveness. © 2013 John Wiley & Sons, Ltd.

The evolution of droplet impacting on thin liquid film at superhydrophilic surface

NASA Astrophysics Data System (ADS)

Li, Yun; Zheng, Yi; Lan, Zhong; Xu, Wei; Ma, Xuehu

2017-12-01

Thin films are ubiquitous in nature, and the evolution of a liquid film after droplet impact is critical in many industrial processes. In this paper, a series of experiments and numerical simulations are conducted to investigate the distribution and evolution features of local temperature as the droplet impacts a thin film on the superhydrophilic surface by the thermal tracing method. A cold area is formed in the center after droplet impacts on heated solid surfaces. For the droplet impact on thin heated liquid film, a ring-shaped low temperature zone is observed in this experiment. Meanwhile, numerical simulation is adopted to analyze the mechanism and the interaction between the droplet and the liquid film. It is found that due to the vortex velocity distribution formed inside the liquid film after the impact, a large part of the droplet has congested. The heating process is not obvious in the congested area, which leads to the formation of a low-temperature area in the results.

Modeling the propagation, transformation and the impact of tsunami on urban areas using the coupling STOC-ML/IC/CADMAS in nested grids - Application to specific sites of Chile to improve the tsunami induced loads prediction.

NASA Astrophysics Data System (ADS)

Mokrani, C.; Catalan, P. A.; Cienfuegos, R.; Arikawa, T.

2016-02-01

A large part of coasts around the world are affected by tsunami impacts, which supposes a challenge when designing coastal protection structures. Numerical models provide predictions of tsunami-induced loads and there time evolution, which can be used to improve sizing rules of coastal structures. However, the numerical assessment of impact loads is an hard stake. Indeed, recent experimental studies have shown that pressure dynamics generated during tsunami impacts are highly sensitive to the incident local shape of the tsunami. Therefore, high numerical resolutions and very accurate models are required to model all stages during which the tsunami shape is modified before the impact. Given the large distances involved in tsunami events, this can be disregarded in favor of computing time. The Port and Airport Research Institute (PARI) has recently developed a three-way coupled model which allows to accurately model the incident tsunami shape while maintaining reasonable computational time. This coupling approach uses three models used in nested grids (cf. Figure 1). The first one (STOC-ML) solves Nonlinear Shallow Water Equations with hydrostatic pressure. It is used to model the tsunami propagation off the coast. The second one (STOC-IC) is a 3D non-hydrostatic model, on which the free-surface position is estimated through the integrated continuity equation. It has shown to accurately describe dispersive and weakly linear effects occurring at the coast vicinity. The third model (CADMAS-SURF) solves fully three-dimensional Navier-Stokes equations and use a VOF method. Highly nonlinear, dispersive effects and wave breaking processes can be included at the wave scale and therefore, a very accurate description of the incident tsunami is provided. Each model have been separately validated from analytical and/or experimental data. The present objective is to highlight recent advances in Coastal Ocean modeling for tsunami modeling and loads prediction by applying this coupling approach to different sites of the Chilean coast. We first present validation tests to highlight the numerical abilities of this coupling. Then, two tsunami cases are considered and both near-shore processes and tsunami-induced loads on structures are analyzed.

The Impact of Deployment Separation on Army Families

DTIC Science & Technology

1984-08-01

REFERENCES 15 I-.- i , L. "I INTRODUCTION Brief family separations resulting from military training exercises are a common phenomenon in Army :ommuni...there have been numerous . studies of military family separation beginning with Rill’s ... (1949) classic study of military- induced separation during...were increased reports of headaches, weight change, sleep disturbances, and changes in menstrual regularity: specif- ically amenorrhea (cessation of

Using inventory data to determine the impact of drought on tree mortality

Treesearch

Greg C. Liknes; Christopher W. Woodall; Charles H. Perry

2012-01-01

Drought has been the subject of numerous recent studies that hint at an acceleration of tree mortality due to climate change. In particular, a recent global survey of tree mortality events implicates drought as the cause of quaking aspen mortality in Minnesota, USA in 2007. In this study, data from the Forest Inventory and Analysis program of the USDA Forest Service...

Long-Term Prescribed Burning Regime Has Little Effect on Springtails in Pine Stands of Southern Arkansas

Treesearch

Michele L. Renschin; Lynne C. Thompson; Michael G. Shelton

2004-01-01

Concerns regarding the impacts of prescribed fires on faunal communities in pine stands have led to numerous studies. One soil/litter insect that may be influenced by fire is springtails, an important member of the forest floor community. A study was conducted in burned and unburned loblolly/shortleaf pine stands in southeastern Arkansas to examine whether springtail...

Microelectronics: The Nature of Work, Skills and Training. An Analysis of Case Studies from Developed and Developing Countries. Training Discussion Paper No. 51.

ERIC Educational Resources Information Center

Acero, Liliana

Microelectronic technologies have had an impact on the nature of work in industry for both white-collar and blue-collar workers. Evidence from sector- and enterprise-level studies shows changes in skills and job content for blue-collar workers involved with numerically controlled machine tools, robots, and other microelectronics applications.…

Constructing Departmental Culture to Support Student Development: Evidence from a Case Study in Rwanda

ERIC Educational Resources Information Center

Schendel, Rebecca

2016-01-01

In recent years, there have been numerous attempts to improve the quality of higher education in Africa, but there is limited knowledge about the impact of these initiatives on student learning. The results of a study published in 2015 offered some initial data in this regard by identifying a lack of improvement in the critical thinking ability of…

Effectiveness of Fire and Fire Surrogate Treatments For Controlling Wildfire Behavior in Piedmont Forests: A Simulation Study

Treesearch

Helen H. Mohr; Thomas A. Waldrop; Sandra Rideout; Ross J. Phillips; Charles T. Flint

2004-01-01

The need for fuel reduction has increased in United States forests due to decades of fire exclusion. Excessive fuel buildup has led to uncharacteristically severe fires in areas with historically short-interval, low-to-moderate-intensity fire regimes. The National Fire and Fire Surrogate (NFFS) Study compared the impacts of three fuel-reduction treatments on numerous...

Energy based simulation of a Timoshenko beam in non-forced rotation. Influence of the piano hammer shank flexibility on the sound

NASA Astrophysics Data System (ADS)

Chabassier, Juliette; Duruflé, Marc

2014-12-01

A nonlinear model for a vibrating Timoshenko beam in non-forced unknown rotation is derived from the virtual work principle applied to a system of beam with mass at the end. The system represents a piano hammer shank coupled to a hammer head. An energy-based numerical scheme is then provided, obtained by non-classical approaches. A major difficulty for time discretization comes from the nonlinear behavior of the kinetic energy of the system. This new numerical scheme is then coupled to a global energy-preserving numerical solution for the whole piano. The obtained numerical simulations show that the pianistic touch clearly influences the spectrum of the piano sound of equally loud isolated notes. These differences do not come from a possible shock excitation on the structure, or from a changing impact point, or a “longitudinal rubbing motion” on the string, since neither of these features is modeled in our study.

Groundwater flow and heat transport for systems undergoing freeze-thaw: Intercomparison of numerical simulators for 2D test cases

NASA Astrophysics Data System (ADS)

Grenier, Christophe; Anbergen, Hauke; Bense, Victor; Chanzy, Quentin; Coon, Ethan; Collier, Nathaniel; Costard, François; Ferry, Michel; Frampton, Andrew; Frederick, Jennifer; Gonçalvès, Julio; Holmén, Johann; Jost, Anne; Kokh, Samuel; Kurylyk, Barret; McKenzie, Jeffrey; Molson, John; Mouche, Emmanuel; Orgogozo, Laurent; Pannetier, Romain; Rivière, Agnès; Roux, Nicolas; Rühaak, Wolfram; Scheidegger, Johanna; Selroos, Jan-Olof; Therrien, René; Vidstrand, Patrik; Voss, Clifford

2018-04-01

In high-elevation, boreal and arctic regions, hydrological processes and associated water bodies can be strongly influenced by the distribution of permafrost. Recent field and modeling studies indicate that a fully-coupled multidimensional thermo-hydraulic approach is required to accurately model the evolution of these permafrost-impacted landscapes and groundwater systems. However, the relatively new and complex numerical codes being developed for coupled non-linear freeze-thaw systems require verification. This issue is addressed by means of an intercomparison of thirteen numerical codes for two-dimensional test cases with several performance metrics (PMs). These codes comprise a wide range of numerical approaches, spatial and temporal discretization strategies, and computational efficiencies. Results suggest that the codes provide robust results for the test cases considered and that minor discrepancies are explained by computational precision. However, larger discrepancies are observed for some PMs resulting from differences in the governing equations, discretization issues, or in the freezing curve used by some codes.

Remote Sensing Observations and Numerical Simulation for Martian Layered Ejecta Craters

NASA Astrophysics Data System (ADS)

Li, L.; Yue, Z.; Zhang, C.; Li, D.

2018-04-01

To understand past Martian climates, it is important to know the distribution and nature of water ice on Mars. Impact craters are widely used ubiquitous indicators for the presence of subsurface water or ice on Mars. Remote sensing observations and numerical simulation are powerful tools for investigating morphological and topographic features on planetary surfaces, and we can use the morphology of layered ejecta craters and hydrocode modeling to constrain possible layering and impact environments. The approach of this work consists of three stages. Firstly, the morphological characteristics of the Martian layered ejecta craters are performed based on Martian images and DEM data. Secondly, numerical modeling layered ejecta are performed through the hydrocode iSALE (impact-SALE). We present hydrocode modeling of impacts onto targets with a single icy layer within an otherwise uniform basalt crust to quantify the effects of subsurface H2O on observable layered ejecta morphologies. The model setup is based on a layered target made up of a regolithic layer (described by the basalt ANEOS), on top an ice layer (described by ANEOS equation of H2O ice), in turn on top of an underlying basaltic crust. The bolide is a 0.8 km diameter basaltic asteroid hitting the Martian surface vertically at a velocity of 12.8 km/s. Finally, the numerical results are compared with the MOLA DEM profile in order to analyze the formation mechanism of Martian layered ejecta craters. Our simulations suggest that the presence of an icy layer significantly modifies the cratering mechanics, and many of the unusual features of SLE craters may be explained by the presence of icy layers. Impact cratering on icy satellites is significantly affected by the presence of subsurface H2O.

Impact of numerical information on risk knowledge regarding human papillomavirus (HPV) vaccination among schoolgirls: a randomised controlled trial.

PubMed

Steckelberg, Anke; Albrecht, Martina; Kezle, Anna; Kasper, Jürgen; Mühlhauser, Ingrid

2013-01-01

In Germany the implementation of human papillomavirus (HPV) vaccination for women aged 12-17 years was accompanied by various campaigns. Evidence-based information including numerical data was not provided. However, standard information leads to overestimation of cancer risk and effects of HPV vaccination. Confidence in children's ability to deal with numerical data is low, especially in disadvantaged pupils. The aim of the present study was to compare the effects of a standard leaflet with an information leaflet supplemented with numerical data on 'risk knowledge' regarding HPV vaccination among schoolgirls. Randomised-controlled short-term trial. All 108 schoolgirls of seven school classes were asked to participate and 105 agreed. Participants were vocational schoolgirls who were preparing for grade 10 graduation and who were members of the target group for HPV vaccination. The control group was asked to read a standard leaflet on HPV vaccination of the German Women's Health Network. The intervention group received the same leaflet, but it was supplemented with numerical information on cancer risk and assumed effects of the HPV vaccination on cancer prevention. As baseline characteristics we surveyed: age, vaccination status, attitude towards HPV vaccination and aspects regarding migration background. The primary end point was 'risk knowledge'. Questionnaire surveys were performed under experimental conditions. Individual randomisation, participants, and intention-to-treat data analyses were blinded. The study was approved by the Ministry of Education and Culture of Schleswig-Holstein and the ethics committee of the Hamburg Chamber of Physicians. We analysed 'risk knowledge' for all 105 randomised participants. Baseline characteristics of the two groups were comparable. Numerical risk information recipients were more likely to give correct answers compared to standard information recipients: Mean value of risk knowledge score (0-5 points): 4.6±1.0 vs. 2.6±1.2 (mean difference 2.0 (95% CI 1.6-2.4)); (P<0.001). Post hoc distractor analysis of single items was performed. Incorrect answers of control participants indicated that cervical cancer risk was highly overestimated whereas total cancer risk was mostly underestimated, and possible impact of HPV vaccination on cancer prevention was overestimated. Supplementing health information on HPV vaccination with numerical data improves 'risk knowledge' among schoolgirls.

Experimental and numerical study of shock-driven collapse of multiple cavity arrays

NASA Astrophysics Data System (ADS)

Betney, Matthew; Anderson, Phillip; Tully, Brett; Doyle, Hugo; Hawker, Nicholas; Ventikos, Yiannis

2014-10-01

This study presents a numerical and experimental investigation of the interaction of a single shock wave with multiple air-filled spherical cavities. The 5 mm diameter cavities are cast in a hydrogel, and collapsed by a shock wave generated by the impact of a projectile fired from a single-stage light-gas gun. Incident shock pressures of up to 1 GPa have been measured, and the results compared to simulations conducted using a front-tracking approach. The authors have previously studied the collapse dynamics of a single cavity. An important process is the formation of a high-speed transverse jet, which impacts the leeward cavity wall and produces a shockwave. The speed of this shock has been measured using schlieren imaging, and the density has been measured with a fibre optic probe. This confirmed the computational prediction that the produced shock is of a higher pressure than the original incident shock. When employing multiple cavity arrays, the strong shock produced by the collapse of one cavity can substantially affect the collapse of further cavities. With control over cavity placement, these effects may be utilised to intensify collapse. This intensification is experimentally measured via analysis of the optical emission.

Gender differences in developmental programming of cardiovascular diseases

PubMed Central

Dasinger, John Henry; Alexander, Barbara T.

2016-01-01

Hypertension is a risk factor for cardiovascular disease, the leading cause of death worldwide. Although multiple factors contribute to the pathogenesis of hypertension, studies by Dr. David Barker reporting an inverse relationship between birth weight and blood pressure led to the hypothesis that slow growth during fetal life increases blood pressure and the risk for cardiovascular disease in later life. It is now recognized that growth during infancy and childhood in addition to exposure to adverse influences during fetal life contribute to the developmental programming of increased cardiovascular risk. Numerous epidemiological studies support the link between influences during early life with later cardiovascular health; experimental models provide proof of principle and indicate that numerous mechanisms contribute to the developmental origins of chronic disease. Sex impacts the severity of cardiovascular risk in experimental models of developmental insult. Yet, few studies examine the influence of sex on blood pressure and cardiovascular health in low birth weight men and women. Fewer still assess how aging impacts sex differences in programmed cardiovascular risk. Thus, the aim of this review is to highlight current data regarding sex differences in the developmental programming of blood pressure and cardiovascular disease. PMID:26814204

How close are we to definitively identifying the respiratory health effects of e-cigarettes?

PubMed

Ratajczak, Alexsandra; Feleszko, Wojciech; Smith, Danielle M; Goniewicz, Maciej

2018-07-01

Use of electronic cigarettes (e-cigarettes) is frequently promoted as a less harmful alternative to cigarette smoking. The impact of repeated inhalation of e-cigarette aerosols on respiratory health is not well understood. Areas covered: Using results from laboratory, observational, and clinical studies, we synthesize evidence relevant to potential respiratory health effects that may result from inhalation of e-cigarette aerosols. Expert commentary: Chemical analyses reveal that e-cigarette aerosols contain numerous respiratory irritants and toxicants. There are documented cytotoxic effects of e-cigarette constituents on lung tissue. Studies among ex-smokers who switched to e-cigarettes note reduced exposure to numerous respiratory toxicants, reduced asthma exacerbations, and chronic obstructive pulmonary disease symptoms. Regular exposure to e-cigarette aerosols is associated with impaired respiratory functioning. Potential respiratory health risks resulting from secondhand e-cigarette aerosol exposure have not been sufficiently evaluated. Current evidence indicates that although e-cigarettes are not without risk, these products seemingly pose fewer respiratory health harms issues compared to tobacco cigarettes. Data from prospective studies and randomized controlled trials examining the impact of e-cigarette use on lung health are needed to better understand respiratory health risks tied to use of these products.

Meso-modeling of Carbon Fiber Composite for Crash Safety Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, Shih-Po; Chen, Yijung; Zeng, Danielle

2017-04-06

In the conventional approach, the material properties for crash safety simulations are typically obtained from standard coupon tests, where the test results only provide single layer material properties used in crash simulations. However, the lay-up effects for the failure behaviors of the real structure were not considered in numerical simulations. Hence, there was discrepancy between the crash simulations and experimental tests. Consequently, an intermediate stage is required for accurate predictions. Some component tests are required to correlate the material models in the intermediate stage. In this paper, a Mazda Tube under high-impact velocity is chosen as an example for themore » crash safety analysis. The tube consists of 24 layers of uni-directional (UD) carbon fiber composite materials, in which 4 layers are perpendicular to, while the other layers are parallel to the impact direction. An LS-DYNA meso-model was constructed with orthotropic material models counting for the single-layer material behaviors. Between layers, a node-based tie-break contact was used for modeling the delamination of the composite material. Since fiber directions are not single-oriented, the lay-up effects could be an important effect. From the first numerical trial, premature material failure occurred due to the use of material parameters obtained directly from the coupon tests. Some parametric studies were conducted to identify the cause of the numerical instability. The finding is that the material failure strength used in the numerical model needs to be enlarged to stabilize the numerical model. Some hypothesis was made to provide the foundation for enlarging the failure strength and the corresponding experiments will be conducted to validate the hypothesis.« less

Impact of air temperature on physically-based maximum precipitation estimation through change in moisture holding capacity of air

NASA Astrophysics Data System (ADS)

Ishida, K.; Ohara, N.; Kavvas, M. L.; Chen, Z. Q.; Anderson, M. L.

2018-01-01

Impact of air temperature on the Maximum Precipitation (MP) estimation through change in moisture holding capacity of air was investigated. A series of previous studies have estimated the MP of 72-h basin-average precipitation over the American River watershed (ARW) in Northern California by means of the Maximum Precipitation (MP) estimation approach, which utilizes a physically-based regional atmospheric model. For the MP estimation, they have selected 61 severe storm events for the ARW, and have maximized them by means of the atmospheric boundary condition shifting (ABCS) and relative humidity maximization (RHM) methods. This study conducted two types of numerical experiments in addition to the MP estimation by the previous studies. First, the air temperature on the entire lateral boundaries of the outer model domain was increased uniformly by 0.0-8.0 °C with 0.5 °C increments for the two severest maximized historical storm events in addition to application of the ABCS + RHM method to investigate the sensitivity of the basin-average precipitation over the ARW to air temperature rise. In this investigation, a monotonous increase was found in the maximum 72-h basin-average precipitation over the ARW with air temperature rise for both of the storm events. The second numerical experiment used specific amounts of air temperature rise that is assumed to happen under future climate change conditions. Air temperature was increased by those specified amounts uniformly on the entire lateral boundaries in addition to application of the ABCS + RHM method to investigate the impact of air temperature on the MP estimate over the ARW under changing climate. The results in the second numerical experiment show that temperature increases in the future climate may amplify the MP estimate over the ARW. The MP estimate may increase by 14.6% in the middle of the 21st century and by 27.3% in the end of the 21st century compared to the historical period.

Model reduction of the numerical analysis of Low Impact Developments techniques

NASA Astrophysics Data System (ADS)

Brunetti, Giuseppe; Šimůnek, Jirka; Wöhling, Thomas; Piro, Patrizia

2017-04-01

Mechanistic models have proven to be accurate and reliable tools for the numerical analysis of the hydrological behavior of Low Impact Development (LIDs) techniques. However, their widespread adoption is limited by their complexity and computational cost. Recent studies have tried to address this issue by investigating the application of new techniques, such as surrogate-based modeling. However, current results are still limited and fragmented. One of such approaches, the Model Order Reduction (MOR) technique, can represent a valuable tool for reducing the computational complexity of a numerical problems by computing an approximation of the original model. While this technique has been extensively used in water-related problems, no studies have evaluated its use in LIDs modeling. Thus, the main aim of this study is to apply the MOR technique for the development of a reduced order model (ROM) for the numerical analysis of the hydrologic behavior of LIDs, in particular green roofs. The model should be able to correctly reproduce all the hydrological processes of a green roof while reducing the computational cost. The proposed model decouples the subsurface water dynamic of a green roof in a) one-dimensional (1D) vertical flow through a green roof itself and b) one-dimensional saturated lateral flow along the impervious rooftop. The green roof is horizontally discretized in N elements. Each element represents a vertical domain, which can have different properties or boundary conditions. The 1D Richards equation is used to simulate flow in the substrate and drainage layers. Simulated outflow from the vertical domain is used as a recharge term for saturated lateral flow, which is described using the kinematic wave approximation of the Boussinesq equation. The proposed model has been compared with the mechanistic model HYDRUS-2D, which numerically solves the Richards equation for the whole domain. The HYDRUS-1D code has been used for the description of vertical flow, while a Finite Volume Scheme has been adopted for lateral flow. Two scenarios involving flat and steep green roofs were analyzed. Results confirmed the accuracy of the reduced order model, which was able to reproduce both subsurface outflow and the moisture distribution in the green roof, significantly reducing the computational cost.

Broadening the study of inductive reasoning: confirmation judgments with uncertain evidence.

PubMed

Mastropasqua, Tommaso; Crupi, Vincenzo; Tentori, Katya

2010-10-01

Although evidence in real life is often uncertain, the psychology of inductive reasoning has, so far, been confined to certain evidence. The present study extends previous research by investigating whether people properly estimate the impact of uncertain evidence on a given hypothesis. Two experiments are reported, in which the uncertainty of evidence is explicitly (by means of numerical values) versus implicitly (by means of ambiguous pictures) manipulated. The results show that people's judgments are highly correlated with those predicted by normatively sound Bayesian measures of impact. This sensitivity to the degree of evidential uncertainty supports the centrality of inductive reasoning in cognition and opens the path to the study of this issue in more naturalistic settings.

Numerical studies on groundwater-grassland relations in an inland arid region in China

NASA Astrophysics Data System (ADS)

Wang, J. R.; Hu, L. T.; Sun, K. N.; Liu, X. M.

2017-08-01

In this study, a 2-D numerical model was developed to assess the impacts of groundwater on grassland ecology in the Hulun Lake Basin. An extreme dry climate scenario and water resource management scenario and their interactions in the Hulun Lake Basin were designed, and their influence on groundwater was evaluated. The results show that the grassland ecology is heavily dependent on groundwater, and a distribution of groundwater with a depth of 8 m correlates well with the distribution of grassland. Under the water resource management scenario, the groundwater level will increase to a maximum value of 2.5 m after 15 years around Hulun Lake. The groundwater level will decrease dramatically under the extreme dry climate scenario, thus affecting the environment.

Diagnostic tool for structural health monitoring: effect of material nonlinearity and vibro-impact process

NASA Astrophysics Data System (ADS)

Hiwarkar, V. R.; Babitsky, V. I.; Silberschmidt, V. V.

2013-07-01

Numerous techniques are available for monitoring structural health. Most of these techniques are expensive and time-consuming. In this paper, vibration-based techniques are explored together with their use as diagnostic tools for structural health monitoring. Finite-element simulations are used to study the effect of material nonlinearity on dynamics of a cracked bar. Additionally, several experiments are performed to study the effect of vibro-impact behavior of crack on its dynamics. It was observed that a change in the natural frequency of the cracked bar due to crack-tip plasticity and vibro-impact behavior linked to interaction of crack faces, obtained from experiments, led to generation of higher harmonics; this can be used as a diagnostic tool for structural health monitoring.

Finite-Time and -Size Scalings in the Evaluation of Large Deviation Functions. Numerical Analysis in Continuous Time

NASA Astrophysics Data System (ADS)

Guevara Hidalgo, Esteban; Nemoto, Takahiro; Lecomte, Vivien

Rare trajectories of stochastic systems are important to understand because of their potential impact. However, their properties are by definition difficult to sample directly. Population dynamics provide a numerical tool allowing their study, by means of simulating a large number of copies of the system, which are subjected to a selection rule that favors the rare trajectories of interest. However, such algorithms are plagued by finite simulation time- and finite population size- effects that can render their use delicate. Using the continuous-time cloning algorithm, we analyze the finite-time and finite-size scalings of estimators of the large deviation functions associated to the distribution of the rare trajectories. We use these scalings in order to propose a numerical approach which allows to extract the infinite-time and infinite-size limit of these estimators.

Aerodynamic Modeling of Oscillating Wing in Hypersonic Flow: a Numerical Study

NASA Astrophysics Data System (ADS)

Zhu, Jian; Hou, Ying-Yu; Ji, Chen; Liu, Zi-Qiang

2016-06-01

Various approximations to unsteady aerodynamics are examined for the unsteady aerodynamic force of a pitching thin double wedge airfoil in hypersonic flow. Results of piston theory, Van Dyke’s second-order theory, Newtonian impact theory, and CFD method are compared in the same motion and Mach number effects. The results indicate that, for this thin double wedge airfoil, Newtonian impact theory is not suitable for these Mach number, while piston theory and Van Dyke’s second-order theory are in good agreement with CFD method for Ma<7.

Heating of Ejecta from a Meteorite Crater by the Perturbed Atmosphere

NASA Astrophysics Data System (ADS)

Kuz'micheva, M. Yu.

2018-03-01

Numerical simulation methods are used to investigate the thermal evolution of ejecta from a meteorite crater in the interaction with the perturbed atmosphere in the first few minutes after the impact. The study considers the role of air radiation, collisions of air molecules with the body's surface, and the heat transfer into the interior in the heat exchange of the ejecta and reveals the possibility of additional heating (compared with that at the time of the impact), which affects the geochemical and paleomagnetic properties of the ejecta.

Impact of Lead Time and Safety Factor in Mixed Inventory Models with Backorder Discounts

NASA Astrophysics Data System (ADS)

Lo, Ming-Cheng; Chao-Hsien Pan, Jason; Lin, Kai-Cing; Hsu, Jia-Wei

This study investigates the impact of safety factor on the continuous review inventory model involving controllable lead time with mixture of backorder discount and partial lost sales. The objective is to minimize the expected total annual cost with respect to order quantity, backorder price discount, safety factor and lead time. A model with normal demand is also discussed. Numerical examples are presented to illustrate the procedures of the algorithms and the effects of parameters on the result of the proposed models are analyzed.

Impact damage resistance of composite fuselage structure, part 1

NASA Technical Reports Server (NTRS)

Dost, E. F.; Avery, W. B.; Ilcewicz, L. B.; Grande, D. H.; Coxon, B. R.

1992-01-01

The impact damage resistance of laminated composite transport aircraft fuselage structures was studied experimentally. A statistically based designed experiment was used to examine numerous material, laminate, structural, and extrinsic (e.g., impactor type) variables. The relative importance and quantitative measure of the effect of each variable and variable interactions on responses including impactor dynamic response, visibility, and internal damage state were determined. The study utilized 32 three-stiffener panels, each with a unique combination of material type, material forms, and structural geometry. Two manufacturing techniques, tow placement and tape lamination, were used to build panels representative of potential fuselage crown, keel, and lower side-panel designs. Various combinations of impactor variables representing various foreign-object-impact threats to the aircraft were examined. Impacts performed at different structural locations within each panel (e.g., skin midbay, stiffener attaching flange, etc.) were considered separate parallel experiments. The relationship between input variables, measured damage states, and structural response to this damage are presented including recommendations for materials and impact test methods for fuselage structure.

Applying a two-dimensional morphodynamic model to assess impacts to Chinook salmon spawning habitat from dam removal

NASA Astrophysics Data System (ADS)

Lee, A. A.; Crosato, A.; Omer, A. Y. A.; Bregoli, F.

2017-12-01

The need for accurate and robust predictive methods of assessing fluvial ecosystems is highlighted by the accelerating practice of dam removal. Dam removal can be a restorative measure, but the sudden release of impounded sediment and change in flow regime may negatively impact aquatic biota and their habitat. This study assesses the performance of a quasi-three-dimensional morphodynamic numerical model, coupled with habitat suitability indices, to predict short-term impacts to Chinook salmon (Oncorhynchus tshawytscha) spawning habitat from dam removal. The 2007 removal of Marmot Dam on the Sandy River (Oregon, U.S.A.) is used as a case study. Delft3D-FLOW is employed to simulate changes in river channel topography, sediment composition and hydrodynamic conditions for a 20-kilometer reach of the Sandy River. The transport of non-uniform sediment and three-dimensional flow effects are included in the model. Output parameters such as flow depth, velocity and substrate are processed to evaluate habitat quality in the year following the Marmot Dam removal. Impacts are evaluated across four life-stages of Chinook salmon. As a hindcast analysis, the morphodynamic model sufficiently reproduces the evolution of river morphology at the reach-scale while requiring only a low level of calibration. The model performs well in predicting impacts to fish passage, but carries more uncertainty for developing life stages. By coupling flow-sediment-biota interactions, this method shows strong potential for habitat assessment in unsteady and non-uniform environments. Computation time is a primary constraint, as it limits grid-cell resolution, modelling of suspended sediment and capacity to characterize the sediment grain size distribution. Research on the effects of suspended sediment on habitat quality is ongoing, and further research is recommended for modelling reservoir erosion processes numerically.

Numerical Study of Unsteady Flow in Centrifugal Cold Compressor

NASA Astrophysics Data System (ADS)

Zhang, Ning; Zhang, Peng; Wu, Jihao; Li, Qing

In helium refrigeration system, high-speed centrifugal cold compressor is utilized to pumped gaseous helium from saturated liquid helium tank at low temperature and low pressure for producing superfluid helium or sub-cooled helium. Stall and surge are common unsteady flow phenomena in centrifugal cold compressors which severely limit operation range and impact efficiency reliability. In order to obtain the installed range of cold compressor, unsteady flow in the case of low mass flow or high pressure ratio is investigated by the CFD. From the results of the numerical analysis, it can be deduced that the pressure ratio increases with the decrease in reduced mass flow. With the decrease of the reduced mass flow, backflow and vortex are intensified near the shroud of impeller. The unsteady flow will not only increase the flow loss, but also damage the compressor. It provided a numerical foundation of analyzing the effect of unsteady flow field and reducing the flow loss, and it is helpful for the further study and able to instruct the designing.

Additive-manufactured sandwich lattice structures: A numerical and experimental investigation

NASA Astrophysics Data System (ADS)

Fergani, Omar; Tronvoll, Sigmund; Brøtan, Vegard; Welo, Torgeir; Sørby, Knut

2017-10-01

The utilization of additive-manufactured lattice structures in engineered products is becoming more and more common as the competitiveness of AM as a production technology has increased during the past several years. Lattice structures may enable important weight reductions as well as open opportunities to build products with customized functional properties, thanks to the flexibility of AM for producing complex geometrical configurations. One of the most critical aspects related to taking AM into new application areas—such as safety critical products—is currently the limited understanding of the mechanical behavior of sandwich-based lattice structure mechanical under static and dynamic loading. In this study, we evaluate manufacturability of lattice structures and the impact of AM processing parameters on the structural behavior of this type of sandwich structures. For this purpose, we conducted static compression testing for a variety of geometry and manufacturing parameters. Further, the study discusses a numerical model capable of predicting the behavior of different lattice structure. A reasonably good correlation between the experimental and numerical results was observed.

Implementation of Improved Transverse Shear Calculations and Higher Order Laminate Theory Into Strain Rate Dependent Analyses of Polymer Matrix Composites

NASA Technical Reports Server (NTRS)

Zhu, Lin-Fa; Kim, Soo; Chattopadhyay, Aditi; Goldberg, Robert K.

2004-01-01

A numerical procedure has been developed to investigate the nonlinear and strain rate dependent deformation response of polymer matrix composite laminated plates under high strain rate impact loadings. A recently developed strength of materials based micromechanics model, incorporating a set of nonlinear, strain rate dependent constitutive equations for the polymer matrix, is extended to account for the transverse shear effects during impact. Four different assumptions of transverse shear deformation are investigated in order to improve the developed strain rate dependent micromechanics model. The validities of these assumptions are investigated using numerical and theoretical approaches. A method to determine through the thickness strain and transverse Poisson's ratio of the composite is developed. The revised micromechanics model is then implemented into a higher order laminated plate theory which is modified to include the effects of inelastic strains. Parametric studies are conducted to investigate the mechanical response of composite plates under high strain rate loadings. Results show the transverse shear stresses cannot be neglected in the impact problem. A significant level of strain rate dependency and material nonlinearity is found in the deformation response of representative composite specimens.

Impact of eliminating fracture intersection nodes in multiphase compositional flow simulation

NASA Astrophysics Data System (ADS)

Walton, Kenneth M.; Unger, Andre J. A.; Ioannidis, Marios A.; Parker, Beth L.

2017-04-01

Algebraic elimination of nodes at discrete fracture intersections via the star-delta technique has proven to be a valuable tool for making multiphase numerical simulations more tractable and efficient. This study examines the assumptions of the star-delta technique and exposes its effects in a 3-D, multiphase context for advective and dispersive/diffusive fluxes. Key issues of relative permeability-saturation-capillary pressure (kr-S-Pc) and capillary barriers at fracture-fracture intersections are discussed. This study uses a multiphase compositional, finite difference numerical model in discrete fracture network (DFN) and discrete fracture-matrix (DFM) modes. It verifies that the numerical model replicates analytical solutions and performs adequately in convergence exercises (conservative and decaying tracer, one and two-phase flow, DFM and DFN domains). The study culminates in simulations of a two-phase laboratory experiment in which a fluid invades a simple fracture intersection. The experiment and simulations evoke different invading fluid flow paths by varying fracture apertures as oil invades water-filled fractures and as water invades air-filled fractures. Results indicate that the node elimination technique as implemented in numerical model correctly reproduces the long-term flow path of the invading fluid, but that short-term temporal effects of the capillary traps and barriers arising from the intersection node are lost.

Molten-Metal Droplet Deposition on a Moving Substrate in Microgravity: Aiding the Development of Novel Technologies for Microelectronic Assembly

NASA Technical Reports Server (NTRS)

Megaridis, C. M.; Bayer, I. S.; Poulikakos, D.; Nayagam, V.

2002-01-01

Driven by advancements in microelectronics manufacturing, this research investigates the oblique (non-axisymmetric) impact of liquid-metal droplets on flat substrates. The problem of interest is relevant to the development of the novel technology of on-demand dispension (printing) of microscopic solder deposits for the surface mounting of microelectronic devices. The technology, known as solder jetting, features on-demand deposition of miniature solder droplets (30 to 120 microns in diameter) in very fine, very accurate patterns using techniques analogous to those developed for the ink-jet printing industry. Despite its promise, severe limitations exist currently with regards to the throughput rates of the technology; some of these limitations are largely due to the lack of the capability for reliable prediction of solder bump positioning and shapes, especially under ballistic deposition conditions where the droplet impact phenomena are inherently three-dimensional. The study consists of a theoretical and an experimental component. The theoretical work uses a finite element formulation to simulate numerically the non-axisymmetric (3-D) fluid mechanics and heat transfer phenomena of a liquid solder droplet impacting at an angle alpha on a flat substrate. The work focuses on the pre-solidification regime. The modeling of the most challenging fluid mechanics part of the process has been completed successfully. It is based upon the full laminar Navier-Stokes equations employing a Lagrangian frame of reference. Due to the large droplet deformation, the surface (skin) as well as the volumetric mesh have to be regenerated during the calculations in order to maintain the high accuracy of the numerical scheme. The pressure and velocity fields are then interpolated on the newly created mesh. The numerical predictions are being tested against experiments, for cases where wetting phenomena are not important. For the impact parameters used in the example shown (We = 2.38, Fr = 16300, Re = 157), the droplet rolls along the substrate, but its shape remains practically axisymmetric for all impact angles within the range from 0 to 60 deg. Interestingly, the substrate/droplet contact area during the recoiling phase of the impact is not a monotonically decreasing function of time. The experimental component of the research tests the numerical predictions and provides necessary input data (contact angles) for the theoretical model. The experiments are performed in microgravity (2.2s drop tower of the NASA GRC) in order to allow for the use of mm-size solder droplets, which make feasible the performance of accurate measurements, while maintaining similitude of the relevant fluid dynamic groups (Re, Fr, We, Ste). Preliminary oblique impact experiments have been performed using water droplets in normal gravity.

Three-dimensional numerical investigation of the separation process in a vortex tube at different operating conditions

NASA Astrophysics Data System (ADS)

Rafiee, Seyed Ehsan; Sadeghiazad, M. M.

2016-06-01

Air separators provide safe, clean, and appropriate air flow to engines and are widely used in vehicles with large engines such as ships and submarines. In this operational study, the separation process inside a Ranque-Hilsch vortex tube cleaning (cooling) system is investigated to analyze the impact of the operating gas type on the vortex tube performance; the operating gases used are air, nitrogen, oxygen, carbon dioxide and nitrogen dioxide. The computational fluid dynamic model used is equipped with a three-dimensional structure, and the steady-state condition is applied during computations. The standard k-ɛ turbulence model is employed to resolve nonlinear flow equations, and various key parameters, such as hot and cold exhaust thermal drops, and power separation rates, are described numerically. The results show that nitrogen dioxide creates the greatest separation power out of all gases tested, and the numerical results are validated by good agreement with available experimental data. In addition, a comparison is made between the use of two different boundary conditions, the pressure-far-field and the pressure-outlet, when analyzing complex turbulent flows inside the air separators. Results present a comprehensive and practical solution for use in future numerical studies.

Improving Preschoolers’ Arithmetic through Number Magnitude Training: The Impact of Non-Symbolic and Symbolic Training

PubMed Central

2016-01-01

The numerical cognition literature offers two views to explain numerical and arithmetical development. The unique-representation view considers the approximate number system (ANS) to represent the magnitude of both symbolic and non-symbolic numbers and to be the basis of numerical learning. In contrast, the dual-representation view suggests that symbolic and non-symbolic skills rely on different magnitude representations and that it is the ability to build an exact representation of symbolic numbers that underlies math learning. Support for these hypotheses has come mainly from correlative studies with inconsistent results. In this study, we developed two training programs aiming at enhancing the magnitude processing of either non-symbolic numbers or symbolic numbers and compared their effects on arithmetic skills. Fifty-six preschoolers were randomly assigned to one of three 10-session-training conditions: (1) non-symbolic training (2) symbolic training and (3) control training working on story understanding. Both numerical training conditions were significantly more efficient than the control condition in improving magnitude processing. Moreover, symbolic training led to a significantly larger improvement in arithmetic than did non-symbolic training and the control condition. These results support the dual-representation view. PMID:27875540

Numerical Modelling and Prediction of Erosion Induced by Hydrodynamic Cavitation

NASA Astrophysics Data System (ADS)

Peters, A.; Lantermann, U.; el Moctar, O.

2015-12-01

The present work aims to predict cavitation erosion using a numerical flow solver together with a new developed erosion model. The erosion model is based on the hypothesis that collapses of single cavitation bubbles near solid boundaries form high velocity microjets, which cause sonic impacts with high pressure amplitudes damaging the surface. The erosion model uses information from a numerical Euler-Euler flow simulation to predict erosion sensitive areas and assess the erosion aggressiveness of the flow. The obtained numerical results were compared to experimental results from tests of an axisymmetric nozzle.

The Impact of Social Media on College Students

ERIC Educational Resources Information Center

Mastrodicasa, Jeanna; Metellus, Paul

2013-01-01

There are numerous ways, positive and negative, in which social media impact college students. Understanding sheer volume of time and the type of activities for which college students use social networking sites is crucial for higher education administrators. Researchers have begun to empirically examine impacts on students' well-being and have…

Evaluating the Impact of Aerosols on Numerical Weather Prediction

NASA Astrophysics Data System (ADS)

Freitas, Saulo; Silva, Arlindo; Benedetti, Angela; Grell, Georg; Members, Wgne; Zarzur, Mauricio

2015-04-01

The Working Group on Numerical Experimentation (WMO, http://www.wmo.int/pages/about/sec/rescrosscut/resdept_wgne.html) has organized an exercise to evaluate the impact of aerosols on NWP. This exercise will involve regional and global models currently used for weather forecast by the operational centers worldwide and aims at addressing the following questions: a) How important are aerosols for predicting the physical system (NWP, seasonal, climate) as distinct from predicting the aerosols themselves? b) How important is atmospheric model quality for air quality forecasting? c) What are the current capabilities of NWP models to simulate aerosol impacts on weather prediction? Toward this goal we have selected 3 strong or persistent events of aerosol pollution worldwide that could be fairly represented in current NWP models and that allowed for an evaluation of the aerosol impact on weather prediction. The selected events includes a strong dust storm that blew off the coast of Libya and over the Mediterranean, an extremely severe episode of air pollution in Beijing and surrounding areas, and an extreme case of biomass burning smoke in Brazil. The experimental design calls for simulations with and without explicitly accounting for aerosol feedbacks in the cloud and radiation parameterizations. In this presentation we will summarize the results of this study focusing on the evaluation of model performance in terms of its ability to faithfully simulate aerosol optical depth, and the assessment of the aerosol impact on the predictions of near surface wind, temperature, humidity, rainfall and the surface energy budget.

Complex crater formation: Insights from combining observations of shock pressure distribution with numerical models at the West Clearwater Lake impact structure

NASA Astrophysics Data System (ADS)

Rae, A. S. P.; Collins, G. S.; Grieve, R. A. F.; Osinski, G. R.; Morgan, J. V.

2017-07-01

Large impact structures have complex morphologies, with zones of structural uplift that can be expressed topographically as central peaks and/or peak rings internal to the crater rim. The formation of these structures requires transient strength reduction in the target material and one of the proposed mechanisms to explain this behavior is acoustic fluidization. Here, samples of shock-metamorphosed quartz-bearing lithologies at the West Clearwater Lake impact structure, Canada, are used to estimate the maximum recorded shock pressures in three dimensions across the crater. These measurements demonstrate that the currently observed distribution of shock metamorphism is strongly controlled by the formation of the structural uplift. The distribution of peak shock pressures, together with apparent crater morphology and geological observations, is compared with numerical impact simulations to constrain parameters used in the block-model implementation of acoustic fluidization. The numerical simulations produce craters that are consistent with morphological and geological observations. The results show that the regeneration of acoustic energy must be an important feature of acoustic fluidization in crater collapse, and should be included in future implementations. Based on the comparison between observational data and impact simulations, we conclude that the West Clearwater Lake structure had an original rim (final crater) diameter of 35-40 km and has since experienced up to 2 km of differential erosion.

Experiments and Dynamic Finite Element Analysis of a Wire-Rope Rockfall Protective Fence

NASA Astrophysics Data System (ADS)

Tran, Phuc Van; Maegawa, Koji; Fukada, Saiji

2013-09-01

The imperative need to protect structures in mountainous areas against rockfall has led to the development of various protection methods. This study introduces a new type of rockfall protection fence made of posts, wire ropes, wire netting and energy absorbers. The performance of this rock fence was verified in both experiments and dynamic finite element analysis. In collision tests, a reinforced-concrete block rolled down a natural slope and struck the rock fence at the end of the slope. A specialized system of measuring instruments was employed to accurately measure the acceleration of the block without cable connection. In particular, the performance of two energy absorbers, which contribute also to preventing wire ropes from breaking, was investigated to determine the best energy absorber. In numerical simulation, a commercial finite element code having explicit dynamic capabilities was employed to create models of the two full-scale tests. To facilitate simulation, certain simplifying assumptions for mechanical data of each individual component of the rock fence and geometrical data of the model were adopted. Good agreement between numerical simulation and experimental data validated the numerical simulation. Furthermore, the results of numerical simulation helped highlight limitations of the testing method. The results of numerical simulation thus provide a deeper understanding of the structural behavior of individual components of the rock fence during rockfall impact. More importantly, numerical simulations can be used not only as supplements to or substitutes for full-scale tests but also in parametric study and design.

Prize of the best thesis 2015: Study of debris discs through state-of-the-art numerical modelling

NASA Astrophysics Data System (ADS)

Kral, Q.; Thébault, P.

2015-12-01

This proceeding summarises the thesis entitled ``Study of debris discs with a new generation numerical model'' by Quentin Kral, for which he obtained the prize of the best thesis in 2015. The thesis brought major contributions to the field of debris disc modelling. The main achievement is to have created, almost ex-nihilo, the first truly self-consistent numerical model able to simultaneously follow the coupled collisional and dynamical evolutions of debris discs. Such a code has been thought as being the ``Holy Grail'' of disc modellers for the past decade, and while several codes with partial dynamics/collisions coupling have been presented, the code developed in this thesis, called ``LIDT-DD'' is the first to achieve a full coupling. The LIDT-DD model, which is the first of a new-generation of fully self-consistent debris disc models is able to handle both planetesimals and dust and create new fragments after each collision. The main idea of LIDT-DD development was to merge into one code two approaches that were so far used separately in disc modelling, that is, an N-body algorithm to investigate the dynamics, and a statistical scheme to explore the collisional evolution. This complex scheme is not straightforward to develop as there are major difficulties to overcome: 1) collisions in debris discs are highly destructive and produce clouds of small fragments after each single impact, 2) the smallest (and most numerous) of these fragments have a strongly size-dependent dynamics because of the radiation pressure, and 3) the dust usually observed in discs is precisely these smallest grains. These extreme constraints had so far prevented all previous attempts at developing self-consistent disc models to succeed. The thesis contains many examples of the use of LIDT-DD that are not yet published but the case of the collision between two asteroid-like bodies is studied in detail. In particular, LIDT-DD is able to predict the different stages that should be observed after such massive collisions that happen mainly in the latest stages of planetary formation. Some giant impact signatures and observability predictions for VLT/SPHERE and JWST/MIRI are given. JWST should be able to detect many of such impacts and would enable to see on-going planetary formation in dozens of planetary systems.

Momentum transfer in asteroid impacts. I. Theory and scaling

NASA Astrophysics Data System (ADS)

Holsapple, Keith A.; Housen, Kevin R.

2012-11-01

When an asteroid experiences an impact, its path is changed. How much it changes is important to know for both asteroid evolution studies and for attempts to prevent an asteroid from impacting the Earth. In an impact process the total momentum of the material is conserved. However, not all of the material is of interest, but only that remaining with the asteroid. The ratio of the change of momentum of the remaining asteroid to that of the impactor is called the momentum multiplication factor; and is commonly given the symbol β. It has been known for some time that β can be greater than unity, and in some cases far greater. That could be a significant factor in attempts to deflect an asteroid with an impact, and can also be important in the stirring of objects in the asteroid belt due to mutual impacts. The escaping crater ejecta are the source of the momentum multiplication. Housen and Holsapple (Housen, K.R., Holsapple, K.A. [2011a]. Icarus 211, 856-875) have given a recent summary of ejecta characteristics and scaling. Here we use those ejecta results to determine how β depends on the impactor properties, on the asteroid size and composition, and establish the paths and time of flight of all of the ejecta particles. The approach is to add the contribution of each element of ejected mass accounting for its initial velocity, its trajectory and whether it escapes the asteroid. The goal in this paper is to provide a theoretical framework of the fundamental results which can be used as a test of the veracity of experiments and detailed numerical calculations of impacts. A subsequent paper will present direct laboratory results and numerical simulations of momentum multiplication in various geological materials.

A simulation of wildfire behavior in piedmont forests

Treesearch

Helen H. Mohr; Thomas A. Waldrop

2006-01-01

Decades of fire exclusion have increased the need for fuel reduction in U.S. forests. The buildup of excessive fuels has led to uncharacteristically severe fires in areas with historically short-interval, low to moderate intensity fire regimes. The National Fire and Fire Surrogate Study compares the impacts of three fuel reduction treatments on numerous response...

The Performance of Local Dependence Measures with Psychological Data

ERIC Educational Resources Information Center

Houts, Carrie R.; Edwards, Michael C.

2013-01-01

The violation of the assumption of local independence when applying item response theory (IRT) models has been shown to have a negative impact on all estimates obtained from the given model. Numerous indices and statistics have been proposed to aid analysts in the detection of local dependence (LD). A Monte Carlo study was conducted to evaluate…

Influence of framing on medical decision making

PubMed Central

Gong, Jingjing; Zhang, Yan; Feng, Jun; Huang, Yonghua; Wei, Yazhou; Zhang, Weiwei

2013-01-01

Numerous studies have demonstrated the robustness of the framing effect in a variety of contexts, especially in medical decision making. Unfortunately, research is still inconsistent as to how so many variables impact framing effects in medical decision making. Additionally, much attention should be paid to the framing effect not only in hypothetical scenarios but also in clinical experience. PMID:27034630

Effects of organic matter removal, soil compaction, and vegetation control on Collembolan populations

Treesearch

Robert J. Eaton; Mary Barbercheck; William D. Smith

2004-01-01

Collembola can be among the most numerous meso-invertebrates in the forest floor and, through their interaction with primary decomposers in the decomposition food web, may affect litter decomposition and consequently site productivity. This study was conducted to determine whether Collembolan abundance could be impacted by organic matter removal, compaction, and...

Training Australian General Practitioners in Rural Public Health: Impact, Desirability and Adaptability of Hybrid Problem-Based Learning

ERIC Educational Resources Information Center

Gladman, Justin; Perkins, David

2013-01-01

Context and Objective: Australian rural general practitioners (GPs) require public health knowledge. This study explored the suitability of teaching complex public health issues related to Aboriginal health by way of a hybrid problem-based learning (PBL) model within an intensive training retreat for GP registrars, when numerous trainees have no…

The Impact of Familial Autism Diagnoses on Autism Symptomatology in Infants and Toddlers

ERIC Educational Resources Information Center

Kozlowski, Alison M.; Matson, Johnny L.; Worley, Julie A.

2012-01-01

Debate regarding the etiology of Autism Spectrum Disorders (ASD) is on the rise with numerous theories being put forth. Currently, the theory with the most empirical support is the interaction of multiple genes. Many studies have provided evidence that as the incidence of ASD increases so do genetic similarities. However, very little research has…

Queering Straight Teachers: Discourse and Identity in Education. Complicated Conversation: A Book Series of Curriculum Studies. Volume 22

ERIC Educational Resources Information Center

Rodriguez, Nelson M., Ed.; Pinar, William F., Ed.

2007-01-01

Much of the focus of anti-homophobic/anti-heterosexist educational theory, curriculum, and pedagogy has examined the impact of homophobia and heterosexism on gay, lesbian, bisexual, and transgender (GLBT) students and teachers. Such a focus has provided numerous theoretical and pedagogical insights, and has informed important changes in…

Evaluation of climate and land use changes on hydrologic processes in the Salt River Basin, Missouri, United States

USDA-ARS?s Scientific Manuscript database

The impact of climate and land use changes on hydrologic processes at the watershed scale is needed by land managers and policy makers to properly assess potential adaptation strategies. While numerous studies have been conducted on hydrologic processes in the Midwest, only a few have analyzed the l...

Physicians Who Treat the Elderly in Rural Florida: Trends Indicating Concerns regarding Access to Care

ERIC Educational Resources Information Center

Gunderson, Anne; Menachemi, Nir; Brummel-Smith, Ken; Brooks, Robert

2006-01-01

Context: Rural elderly patients are faced with numerous challenges in accessing care. Additional strains to access may be occurring given recent market pressures, which would have significant impact on this vulnerable population. Purpose: This study focused on the practice patterns and future plans of rural Florida physicians who routinely see…

Numerical Analysis Study of the Failure Mechanism of Transparent Materials During Low Velocity Impact Used in Protective Systems

DTIC Science & Technology

2011-07-01

UCRL -50694 (Lawrence Rad.Lab. 1969) 9 Wilkins M.L., ’Ballistic materials and penetration mechanics’ ed. Laib1e.R.C. (Elsevier Sci.Publ.1980) pp.225...ORGANIZATION COPIES ORGANIZATION 2 DARPA L CHRISTODOULOU J GOLDWASSER 3701 N FAIRFAX DR ARLINGTON VA 22217-5600 2 DIRECTED

The Impact of Five Missing Data Treatments on a Cross-Classified Random Effects Model

ERIC Educational Resources Information Center

Hoelzle, Braden R.

2012-01-01

The present study compared the performance of five missing data treatment methods within a Cross-Classified Random Effects Model environment under various levels and patterns of missing data given a specified sample size. Prior research has shown the varying effect of missing data treatment options within the context of numerous statistical…

Influence of framing on medical decision making.

PubMed

Gong, Jingjing; Zhang, Yan; Feng, Jun; Huang, Yonghua; Wei, Yazhou; Zhang, Weiwei

2013-01-01

Numerous studies have demonstrated the robustness of the framing effect in a variety of contexts, especially in medical decision making. Unfortunately, research is still inconsistent as to how so many variables impact framing effects in medical decision making. Additionally, much attention should be paid to the framing effect not only in hypothetical scenarios but also in clinical experience.

Can High School Assessments Predict Developmental Education Enrollment in New Mexico?

ERIC Educational Resources Information Center

Weldon, Tyler L.

2013-01-01

Thousands of American's enter postsecondary institutions every year and many are under prepared for college-level work. Subsequently, students enroll in or are placed in remedial courses in preparation for the rigor of college level classes. Numerous studies have looked at the impact of developmental course work on student outcomes, but few focus…

Where We Live: The Unexpected Influence of Urban Neighborhoods on the Academic Performance of African American Adolescents

ERIC Educational Resources Information Center

Francois, Samantha; Overstreet, Stacy; Cunningham, Michael

2012-01-01

Adolescents who live in low-income neighborhoods face numerous unique challenges. Examining their resilience in multiple contexts sheds light on what contributes to the diverse outcomes of these youth. The current study examines how adolescents' reports of structural and experiential neighborhood characteristics buffered the impact of exposure to…

The Relationship between Instructor Humor Orientation and Students' Report on Second Language Learning

ERIC Educational Resources Information Center

Ziyaeemehr, Ali; Kumar, Vijay

2014-01-01

Humor is an integral component of any language and therefore has an impact on the way languages are acquired/learned. Numerous studies have investigated the role of instructor humor in teaching/learning processes; however, there is little empirical research on the relationship between instructor humor and learning of a second language. This paper…

The Social Value of Community-Based Adult Education in Limerick City

ERIC Educational Resources Information Center

Neville, Patricia; O'Dwyer, Maria; Power, Martin J.

2014-01-01

This article documents the findings of a qualitative study into the social value of community-based adult education in Limerick City. The article demonstrates that participants experience significant improvements in numerous facets of their lives and we argue that it is crucial that we recognise the multiple and inter-connected social impacts that…

Impacts of wildfire recency and frequency on an Appalachian oak forest

Treesearch

Melissa A. Thomas-Van Gundy; Katharina U. Wood; James S. Rentch

2015-01-01

Cabwaylingo State Forest in southern West Virginia has experienced numerous anthropogenic wildfires over the past 36 years. In this case study, we assessed the relationship between fire frequency and recency and stand composition and structure, with emphasis on oak and its competitors. Frequent and recent fire was significantly correlated with reduced red maple...

Part-Time Community College Instructors Teaching in Learning Communities: An Exploratory Multiple Case Study

ERIC Educational Resources Information Center

Paterson, John W.

2017-01-01

Community colleges have a greater portion of students at-risk for college completion than four-year schools and faculty at these institutions are overwhelmingly and increasingly part-time. Learning communities have been identified as a high-impact practice with numerous benefits documented for community college instructors and students: a primary…

Modeling connected and autonomous vehicles in heterogeneous traffic flow

NASA Astrophysics Data System (ADS)

Ye, Lanhang; Yamamoto, Toshiyuki

2018-01-01

The objective of this study was to develop a heterogeneous traffic-flow model to study the possible impact of connected and autonomous vehicles (CAVs) on the traffic flow. Based on a recently proposed two-state safe-speed model (TSM), a two-lane cellular automaton (CA) model was developed, wherein both the CAVs and conventional vehicles were incorporated in the heterogeneous traffic flow. In particular, operation rules for CAVs are established considering the new characteristics of this emerging technology, including autonomous driving through the adaptive cruise control and inter-vehicle connection via short-range communication. Simulations were conducted under various CAV-penetration rates in the heterogeneous flow. The impact of CAVs on the road capacity was numerically investigated. The simulation results indicate that the road capacity increases with an increase in the CAV-penetration rate within the heterogeneous flow. Up to a CAV-penetration rate of 30%, the road capacity increases gradually; the effect of the difference in the CAV capability on the growth rate is insignificant. When the CAV-penetration rate exceeds 30%, the growth rate is largely decided by the capability of the CAV. The greater the capability, the higher the road-capacity growth rate. The relationship between the CAV-penetration rate and the road capacity is numerically analyzed, providing some insights into the possible impact of the CAVs on traffic systems.

Observation of the pressure effect in simulations of droplets splashing on a dry surface

NASA Astrophysics Data System (ADS)

Boelens, A. M. P.; Latka, A.; de Pablo, J. J.

2018-06-01

At atmospheric pressure, a drop of ethanol impacting on a solid surface produces a splash. Reducing the ambient pressure below its atmospheric value suppresses this splash. The origin of this so-called pressure effect is not well understood, and this study presents an in-depth comparison between various theoretical models that aim to predict splashing and simulations. In this paper, the pressure effect is explored numerically by resolving the Navier-Stokes equations at a 3-nm resolution. In addition to reproducing numerous experimental observations, it is found that different models all provide elements of what is observed in the simulations. The skating droplet model correctly predicts the existence and scaling of a gas film under the droplet, the lamella formation theory is able to correctly predict the scaling of the lamella ejection velocity as a function of the impact velocity for liquids with different viscosity, and lastly, the dewetting theory's hypothesis of a lift force acting on the liquid sheet after ejection is consistent with our results.

Impact of oxLDL on Cholesterol-Rich Membrane Rafts

PubMed Central

Levitan, Irena; Shentu, Tzu-Pin

2011-01-01

Numerous studies have demonstrated that cholesterol-rich membrane rafts play critical roles in multiple cellular functions. However, the impact of the lipoproteins on the structure, integrity and cholesterol composition of these domains is not well understood. This paper focuses on oxidized low-density lipoproteins (oxLDLs) that are strongly implicated in the development of the cardiovascular disease and whose impact on membrane cholesterol and on membrane rafts has been highly controversial. More specifically, we discuss three major criteria for the impact of oxLDL on membrane rafts: distribution of different membrane raft markers, changes in membrane cholesterol composition, and changes in lipid packing of different membrane domains. We also propose a model to reconcile the controversy regarding the relationship between oxLDL, membrane cholesterol, and the integrity of cholesterol-rich membrane domains. PMID:21490811

Impact of mussel bioengineering on fine-grained sediment dynamics in a coastal lagoon: A numerical modelling investigation

NASA Astrophysics Data System (ADS)

Forsberg, Pernille L.; Lumborg, Ulrik; Bundgaard, Klavs; Ernstsen, Verner B.

2017-12-01

Rødsand lagoon in southeast Denmark is a non-tidal coastal lagoon. It is home to a wide range of marine flora and fauna and part of the Natura 2000 network. An increase in turbidity through elevated levels of suspended sediment concentration (SSC) within the lagoon may affect the ecosystem health due to reduced light penetration. Increasing SSC levels within Rødsand lagoon could be caused by increasing storm intensity or by a sediment spill from dredging activities west of the lagoon in relation to the planned construction of the Fehmarnbelt fixed link between Denmark and Germany. The aim of the study was to investigate the impact of a mussel reef on sediment import and SSC in a semi-enclosed lagoon through the development of a bioengineering modelling application that makes it possible to include the filtrating effect of mussels in a numerical model of the lagoonal system. The numerical implementation of an exterior mussel reef generated a reduction in the SSC in the vicinity of the reef, through the adjacent inlet and in the western part of the lagoon. The mussel reef reduced the sediment import to Rødsand lagoon by 13-22% and reduced the SSC within Rødsand lagoon by 5-9% depending on the filtration rate and the reef length. The results suggest that the implementation of a mussel reef has the potential to relieve the pressure of increasing turbidity levels within a semi-enclosed lagoonal system. However, further assessment and development of the bioengineering application and resulting ecosystem impacts are necessary prior to actual implementation.

A numerical study of tsunami wave impact and run-up on coastal cliffs using a CIP-based model

NASA Astrophysics Data System (ADS)

Zhao, Xizeng; Chen, Yong; Huang, Zhenhua; Hu, Zijun; Gao, Yangyang

2017-05-01

There is a general lack of understanding of tsunami wave interaction with complex geographies, especially the process of inundation. Numerical simulations are performed to understand the effects of several factors on tsunami wave impact and run-up in the presence of gentle submarine slopes and coastal cliffs, using an in-house code, a constrained interpolation profile (CIP)-based model. The model employs a high-order finite difference method, the CIP method, as the flow solver; utilizes a VOF-type method, the tangent of hyperbola for interface capturing/slope weighting (THINC/SW) scheme, to capture the free surface; and treats the solid boundary by an immersed boundary method. A series of incident waves are arranged to interact with varying coastal geographies. Numerical results are compared with experimental data and good agreement is obtained. The influences of gentle submarine slope, coastal cliff and incident wave height are discussed. It is found that the tsunami amplification factor varying with incident wave is affected by gradient of cliff slope, and the critical value is about 45°. The run-up on a toe-erosion cliff is smaller than that on a normal cliff. The run-up is also related to the length of a gentle submarine slope with a critical value of about 2.292 m in the present model for most cases. The impact pressure on the cliff is extremely large and concentrated, and the backflow effect is non-negligible. Results of our work are highly precise and helpful in inverting tsunami source and forecasting disaster.

Does Regular Online Testing Enhance Student Learning in the Numerical Sciences? Robust Evidence from a Large Data Set

ERIC Educational Resources Information Center

Angus, Simon D.; Watson, Judith

2009-01-01

While a number of studies have been conducted on the impact of online assessment and teaching methods on student learning, the field does not seem settled around the promised benefits of such approaches. It is argued that the reason for this state of affairs is that few studies have been able to control for a number of confounding factors in…

The Relationship between Stated Beliefs, Classroom Practices, and Reading Research Studies of Oral Corrective Feedback in Four ESL Teachers

ERIC Educational Resources Information Center

Kamiya, Nobuhiro

2012-01-01

A call for a bridge between research and practice is nothing new, yet it seems to be an impossible task to accomplish. Despite the dedicated efforts made by numerous researchers in the past, the world is still largely separate between researchers and teachers. One piece of evidence is that research studies seem to have only a little impact on…

77 FR 69436 - JPSS Polar Satellite-Gap Mitigation-Request for Public Comment

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-19

... positive steps to mitigate the negative impacts to NOAA's numerical weather forecasts that could be...-satellite data, weather modeling, and data assimilation improvements. NOAA is convening teams of internal... of NOAA's numerical weather forecasts should we experience a loss of polar satellite environmental...

Flow and fracture behavior of aluminum alloy 6082-T6 at different tensile strain rates and triaxialities.

PubMed

Chen, Xuanzhen; Peng, Yong; Peng, Shan; Yao, Song; Chen, Chao; Xu, Ping

2017-01-01

This study aims to investigate the flow and fracture behavior of aluminum alloy 6082-T6 (AA6082-T6) at different strain rates and triaxialities. Two groups of Charpy impact tests were carried out to further investigate its dynamic impact fracture property. A series of tensile tests and numerical simulations based on finite element analysis (FEA) were performed. Experimental data on smooth specimens under various strain rates ranging from 0.0001~3400 s-1 shows that AA6082-T6 is rather insensitive to strain rates in general. However, clear rate sensitivity was observed in the range of 0.001~1 s-1 while such a characteristic is counteracted by the adiabatic heating of specimens under high strain rates. A Johnson-Cook constitutive model was proposed based on tensile tests at different strain rates. In this study, the average stress triaxiality and equivalent plastic strain at facture obtained from numerical simulations were used for the calibration of J-C fracture model. Both of the J-C constitutive model and fracture model were employed in numerical simulations and the results was compared with experimental results. The calibrated J-C fracture model exhibits higher accuracy than the J-C fracture model obtained by the common method in predicting the fracture behavior of AA6082-T6. Finally, the Scanning Electron Microscope (SEM) of fractured specimens with different initial stress triaxialities were analyzed. The magnified fractographs indicate that high initial stress triaxiality likely results in dimple fracture.

Impact of model complexity and multi-scale data integration on the estimation of hydrogeological parameters in a dual-porosity aquifer

NASA Astrophysics Data System (ADS)

Tamayo-Mas, Elena; Bianchi, Marco; Mansour, Majdi

2018-03-01

This study investigates the impact of model complexity and multi-scale prior hydrogeological data on the interpretation of pumping test data in a dual-porosity aquifer (the Chalk aquifer in England, UK). In order to characterize the hydrogeological properties, different approaches ranging from a traditional analytical solution (Theis approach) to more sophisticated numerical models with automatically calibrated input parameters are applied. Comparisons of results from the different approaches show that neither traditional analytical solutions nor a numerical model assuming a homogenous and isotropic aquifer can adequately explain the observed drawdowns. A better reproduction of the observed drawdowns in all seven monitoring locations is instead achieved when medium and local-scale prior information about the vertical hydraulic conductivity (K) distribution is used to constrain the model calibration process. In particular, the integration of medium-scale vertical K variations based on flowmeter measurements lead to an improvement in the goodness-of-fit of the simulated drawdowns of about 30%. Further improvements (up to 70%) were observed when a simple upscaling approach was used to integrate small-scale K data to constrain the automatic calibration process of the numerical model. Although the analysis focuses on a specific case study, these results provide insights about the representativeness of the estimates of hydrogeological properties based on different interpretations of pumping test data, and promote the integration of multi-scale data for the characterization of heterogeneous aquifers in complex hydrogeological settings.

Interaction of aluminum oxide nanoparticles with flow of polyvinyl alcohol solutions base nanofluids over a wedge

NASA Astrophysics Data System (ADS)

Hassan, Mohsan; Faisal, Abrar; Bhatti, Muhammad Mubashir

2018-02-01

Polyvinyl alcohol (PVA) is an important industrial chemical, which is used in numerous chemical engineering applications. It is important to study and predict the flow behavior of PVA solutions and the role of nanoparticles in heat transfer applications to be used in chemical processes on industrial scale. Therefore, the present study deals with the PVA solution-based non-Newtonian Al2O3-nanofluid flow along with heat transfer over wedge. The power-law model is used for this non-Newtonian nanofluid which exhibited shear-thinning behavior. The influences of PVA and nanoparticles concentrations on the characteristics of velocity and temperature profiles are examined graphically. The impacts of these parameters on wall shear stress and convective heat transfer coefficient are also studied through tabular form. During the numerical computations, the impacts of these parameters on flow index and consistency index along with other physical properties of nanofluid are also considered. In this study, we found an improvement in heat transfer and temperature profile of fluid by distribution of Al2O3 nanoparticles. It is also noticed that resistance between adjacent layers of moving fluid is enhanced due to these nanoparticles which leads to decline in velocity profile and increases in shear stress at wall.

A Gas-Actuated Projectile Launcher for High-Energy Impact Testing of Structures

NASA Technical Reports Server (NTRS)

Ambur, Damodar R.; Jaunky, Navin; Lawson, Robin E.; Knight, Norman F., Jr.; Lyle, Karen H.

1999-01-01

A gas-act,uated penetration device has been developed for high-energy impact testing of structures. The high-energy impact. t,estiiig is for experimental simulation of uncontained engine failures. The non-linear transient finite element, code LS-DYNA3D has been used in the numerical simula.tions of a titanium rectangular blade with a.n aluminum target, plate. Threshold velocities for different combinations of pitch and yaw angles of the impactor were obtained for the impactor-target, t8est configuration in the numerica.1 simulations. Complet,e penet,ration of the target plate was also simulat,ed numerically. Finally, limited comparison of analytical and experimental results is presented for complete penetration of the target by the impactor.

A Design Study of the Inflated Sphere Landing Vehicle, Including the Landing Performance and the Effects of Deviations from Design Conditions

NASA Technical Reports Server (NTRS)

Martin, E. Dale

1961-01-01

The impact motion of the inflated sphere landing vehicle with a payload centrally supported from the spherical skin by numerous cords has been determined on the assumption of uniform isentropic gas compression during impact. The landing capabilities are determined for a system containing suspension cords of constant cross section. The effects of deviations in impact velocity and initial gas temperature from the design conditions are studied. Also discussed are the effects of errors in the time at which the skin is ruptured. These studies indicate how the design parameters should be chosen to insure reliability of the landing system. Calculations have been made and results are presented for a sphere inflated with hydrogen, landing on the moon in the absence of an atmosphere. The results are presented for one value of the skin-strength parameter.

Tsunami Impact Computed from Offshore Modeling and Coastal Amplification Laws: Insights from the 2004 Indian Ocean Tsunami

NASA Astrophysics Data System (ADS)

Hébert, H.; Schindelé, F.

2015-12-01

The 2004 Indian Ocean tsunami gave the opportunity to gather unprecedented tsunami observation databases for various coastlines. We present here an analysis of such databases gathered for 3 coastlines, among the most impacted in 2004 in the intermediate- and far field: Thailand-Myanmar, SE India-Sri Lanka, and SE Madagascar. Non-linear shallow water tsunami modeling performed on a single 4' coarse bathymetric grid is compared to these observations, in order to check to which extent a simple approach based on the usual energy conservation laws (either Green's or Synolakis laws) can explain the data. The idea is to fit tsunami data with numerical modeling carried out without any refined coastal bathymetry/topography. To this end several parameters are discussed, namely the bathymetric depth to which model results must be extrapolated (using the Green's law), or the mean bathymetric slope to consider near the studied coast (when using the Synolakis law). Using extrapolation depths from 1 to 10 m generally allows a good fit; however, a 0.1 m is required for some others, especially in the far field (Madagascar) possibly due to enhanced numerical dispersion. Such a method also allows describing the tsunami impact variability along a given coastline. Then, using a series of scenarios, we propose a preliminary statistical assessment of tsunami impact for a given earthquake magnitude along the Indonesian subduction. Conversely, the sources mostly contributing to a specific hazard can also be mapped onto the sources, providing a first order definition of which sources are threatening the 3 studied coastlines.

Bifurcations of periodic motion in a three-degree-of-freedom vibro-impact system with clearance

NASA Astrophysics Data System (ADS)

Liu, Yongbao; Wang, Qiang; Xu, Huidong

2017-07-01

The smooth bifurcation and grazing non-smooth bifurcation of periodic motion of a three-degree-of-freedom vibro-impact system with clearance are studied in this paper. Firstly, a periodic solution of vibro-impact system is solved and a six-dimensional Poincaré map is established. Then, for the six-dimensional Poincaré map, the analytic expressions of all eigenvalues of Jacobi matrix with respect to parameters are unavailable. This implies that with application of the classical critical criterion described by the properties of eigenvalues, we have to numerically compute eigenvalues point by point and check their properties to search for the bifurcation points. Such the numerical calculation is a laborious job in the process of determining bifurcation points. To overcome the difficulty that originates from the classical bifurcation criteria, the explicit critical criteria without using eigenvalues calculation of high-dimensional map are applied to determine bifurcation points of Co-dimension-one period doubling bifurcation and Co-dimension-one Neimark-Sacker bifurcation and Co-dimension-two Flip-Neimark-Sacker bifurcation, and then local dynamical behaviors of these bifurcations are analyzed. Moreover, the directions of period doubling bifurcation and Neimark-Sacker bifurcation are analyzed by center manifold reduction theory and normal form approach. Finally, the existence of the grazing periodic motion of the vibro-impact system is analyzed and the grazing bifurcation point is obtained, the discontinuous grazing bifurcation behavior is studied based on the compound normal form map near the grazing point, the discontinuous jumping phenomenon and co-existing multiple solutions near the grazing bifurcation point are revealed.

Combining shock barometry with numerical modeling: Insights into complex crater formation—The example of the Siljan impact structure (Sweden)

NASA Astrophysics Data System (ADS)

Holm-Alwmark, Sanna; Rae, Auriol S. P.; Ferrière, Ludovic; Alwmark, Carl; Collins, Gareth S.

2017-12-01

Siljan, central Sweden, is the largest known impact structure in Europe. It was formed at about 380 Ma, in the late Devonian period. The structure has been heavily eroded to a level originally located underneath the crater floor, and to date, important questions about the original size and morphology of Siljan remain unanswered. Here we present the results of a shock barometry study of quartz-bearing surface and drill core samples combined with numerical modeling using iSALE. The investigated 13 bedrock granitoid samples show that the recorded shock pressure decreases with increasing depth from 15 to 20 GPa near the (present) surface, to 10-15 GPa at 600 m depth. A best-fit model that is consistent with observational constraints relating to the present size of the structure, the location of the downfaulted sediments, and the observed surface and vertical shock barometry profiles is presented. The best-fit model results in a final crater (rim-to-rim) diameter of 65 km. According to our simulations, the original Siljan impact structure would have been a peak-ring crater. Siljan was formed in a mixed target of Paleozoic sedimentary rocks overlaying crystalline basement. Our modeling suggests that, at the time of impact, the sedimentary sequence was approximately 3 km thick. Since then, there has been around 4 km of erosion of the structure.

An approach to achieve progress in spacecraft shielding

NASA Astrophysics Data System (ADS)

Thoma, K.; Schäfer, F.; Hiermaier, S.; Schneider, E.

2004-01-01

Progress in shield design against space debris can be achieved only when a combined approach based on several tools is used. This approach depends on the combined application of advanced numerical methods, specific material models and experimental determination of input parameters for these models. Examples of experimental methods for material characterization are given, covering the range from quasi static to very high strain rates for materials like Nextel and carbon fiber-reinforced materials. Mesh free numerical methods have extraordinary capabilities in the simulation of extreme material behaviour including complete failure with phase changes, combined with shock wave phenomena and the interaction with structural components. In this paper the benefits from combining numerical methods, material modelling and detailed experimental studies for shield design are demonstrated. The following examples are given: (1) Development of a material model for Nextel and Kevlar-Epoxy to enable numerical simulation of hypervelocity impacts on complex heavy protection shields for the International Space Station. (2) The influence of projectile shape on protection performance of Whipple Shields and how experimental problems in accelerating such shapes can be overcome by systematic numerical simulation. (3) The benefits of using metallic foams in "sandwich bumper shields" for spacecraft and how to approach systematic characterization of such materials.

Hybrid RANS-LES using high order numerical methods

NASA Astrophysics Data System (ADS)

Henry de Frahan, Marc; Yellapantula, Shashank; Vijayakumar, Ganesh; Knaus, Robert; Sprague, Michael

2017-11-01

Understanding the impact of wind turbine wake dynamics on downstream turbines is particularly important for the design of efficient wind farms. Due to their tractable computational cost, hybrid RANS/LES models are an attractive framework for simulating separation flows such as the wake dynamics behind a wind turbine. High-order numerical methods can be computationally efficient and provide increased accuracy in simulating complex flows. In the context of LES, high-order numerical methods have shown some success in predictions of turbulent flows. However, the specifics of hybrid RANS-LES models, including the transition region between both modeling frameworks, pose unique challenges for high-order numerical methods. In this work, we study the effect of increasing the order of accuracy of the numerical scheme in simulations of canonical turbulent flows using RANS, LES, and hybrid RANS-LES models. We describe the interactions between filtering, model transition, and order of accuracy and their effect on turbulence quantities such as kinetic energy spectra, boundary layer evolution, and dissipation rate. This work was funded by the U.S. Department of Energy, Exascale Computing Project, under Contract No. DE-AC36-08-GO28308 with the National Renewable Energy Laboratory.

Numerical investigation of two interacting parallel thruster-plumes and comparison to experiment

NASA Astrophysics Data System (ADS)

Grabe, Martin; Holz, André; Ziegenhagen, Stefan; Hannemann, Klaus

2014-12-01

Clusters of orbital thrusters are an attractive option to achieve graduated thrust levels and increased redundancy with available hardware, but the heavily under-expanded plumes of chemical attitude control thrusters placed in close proximity will interact, leading to a local amplification of downstream fluxes and of back-flow onto the spacecraft. The interaction of two similar, parallel, axi-symmetric cold-gas model thrusters has recently been studied in the DLR High-Vacuum Plume Test Facility STG under space-like vacuum conditions, employing a Patterson-type impact pressure probe with slot orifice. We reproduce a selection of these experiments numerically, and emphasise that a comparison of numerical results to the measured data is not straight-forward. The signal of the probe used in the experiments must be interpreted according to the degree of rarefaction and local flow Mach number, and both vary dramatically thoughout the flow-field. We present a procedure to reconstruct the probe signal by post-processing the numerically obtained flow-field data and show that agreement to the experimental results is then improved. Features of the investigated cold-gas thruster plume interaction are discussed on the basis of the numerical results.

Your favorite number is special (to you): Evidence for item-level differences in retrieval of information from numerals.

PubMed

Dickson, Danielle S; Federmeier, Kara D

2018-05-22

Arabic numerals have come to be used for many purposes beyond representing a particular quantity (e.g., as a label for an athlete on their jersey), but it remains to be determined how this type of meaningfulness is accessed and utilized by readers. Motivated by previous work showing that item-level ratings of personal familiarity can influence traditional indices of memory retrieval, we recorded ERPs while participants read double-digit Arabic numerals (e.g., "65"), presented in a list, and rated whether or not each was familiar/personally meaningful. All numbers repeated after a few intervening trials. The effect of number repetition on the N400 was not impacted by subjective judgments of familiarity, suggesting that all numbers (personally meaningful or not) make initial contact with semantics, facilitating semantic access on second exposure. However, consistent with findings from prior studies of memory for letter strings and visual patterns, there was a late positivity (LPC) on second presentation, selective to numbers rated as familiar. This is the first electrophysiological evidence that readers can use Arabic numerals to guide explicit retrieval of non-numerical information. Copyright © 2018 Elsevier Ltd. All rights reserved.

A History of Computer Numerical Control.

ERIC Educational Resources Information Center

Haggen, Gilbert L.

Computer numerical control (CNC) has evolved from the first significant counting method--the abacus. Babbage had perhaps the greatest impact on the development of modern day computers with his analytical engine. Hollerith's functioning machine with punched cards was used in tabulating the 1890 U.S. Census. In order for computers to become a…

Biology and impacts of Pacific island invasive species: Capra hircus, the feral goat, (Mammalia: Bovidae)

Treesearch

Mark W. Chynoweth; Creighton M. Litton; Christopher A. Lepczyk; Steven C. Hess; Susan Cordell

2013-01-01

Domestic goats, Capra hircus, were intentionally introduced to numerous oceanic islands beginning in the sixteenth century. The remarkable ability of C. hircus to survive in a variety of conditions has enabled this animal to become feral and impact native ecosystems on islands throughout the world. Direct ecological impacts...

Research Impact Assessment in Agriculture--A Review of Approaches and Impact Areas

ERIC Educational Resources Information Center

Weißhuhn, Peter; Helming, Katharina; Ferretti, Johanna

2018-01-01

Research has a role to play in society's endeavour for sustainable development. This is particularly true for agricultural research, since agriculture is at the nexus between numerous sustainable development goals. Yet, generally accepted methods for linking research outcomes to sustainability impacts are missing. We conducted a review of…

A Test of Maxwell's Z Model Using Inverse Modeling

NASA Technical Reports Server (NTRS)

Anderson, J. L. B.; Schultz, P. H.; Heineck, T.

2003-01-01

In modeling impact craters a small region of energy and momentum deposition, commonly called a "point source", is often assumed. This assumption implies that an impact is the same as an explosion at some depth below the surface. Maxwell's Z Model, an empirical point-source model derived from explosion cratering, has previously been compared with numerical impact craters with vertical incidence angles, leading to two main inferences. First, the flowfield center of the Z Model must be placed below the target surface in order to replicate numerical impact craters. Second, for vertical impacts, the flow-field center cannot be stationary if the value of Z is held constant; rather, the flow-field center migrates downward as the crater grows. The work presented here evaluates the utility of the Z Model for reproducing both vertical and oblique experimental impact data obtained at the NASA Ames Vertical Gun Range (AVGR). Specifically, ejection angle data obtained through Three-Dimensional Particle Image Velocimetry (3D PIV) are used to constrain the parameters of Maxwell's Z Model, including the value of Z and the depth and position of the flow-field center via inverse modeling.

Drop impact into a deep pool: vortex shedding and jet formation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Agbaglah, G.; Thoraval, M. -J.; Thoroddsen, S. T.

2015-02-01

One of the simplest splashing scenarios results from the impact of a single drop on a deep pool. The traditional understanding of this process is that the impact generates an axisymmetric sheet-like jet that later breaks up into secondary droplets. Recently it was shown that even this simplest of scenarios is more complicated than expected because multiple jets can be generated from a single impact event and there are transitions in the multiplicity of jets as the experimental parameters are varied. Here, we use experiments and numerical simulations of a single drop impacting on a deep pool to examine themore » transition from impacts that produce a single jet to those that produce two jets. Using high-speed X-ray imaging methods we show that vortex separation within the drop leads to the formation of a second jet long after the formation of the ejecta sheet. Using numerical simulations we develop a phase diagram for this transition and show that the capillary number is the most appropriate order parameter for the transition.« less

SEASAT economic assessment. Volume 2: The SEASAT system description and performance. [performance prediction and systems analysis for seasat satellites

NASA Technical Reports Server (NTRS)

1975-01-01

Results are presented of preliminary trade-off studies of operational SEASAT systems. The trade-off studies were used as the basis for the estimation of costs and net benefits of the operational SEASAT system. Also presented are the preliminary results of simulation studies that were designed to lead to a measure of the impact of SEASAT data through the use of numerical weather forecast models.

Modeling of aerodynamic heat flux and thermoelastic behavior of nose caps of hypersonic vehicles

NASA Astrophysics Data System (ADS)

Persova, Marina G.; Soloveichik, Yury G.; Belov, Vasiliy K.; Kiselev, Dmitry S.; Vagin, Denis V.; Domnikov, Petr A.; Patrushev, Ilya I.; Kurskiy, Denis N.

2017-07-01

In this paper, the problem of numerical modeling of thermoelastic behavior of nose caps of hypersonic vehicles at different angles of attack is considered. 3D finite element modeling is performed by solving the coupled heat and elastic problems taking into account thermal and mechanical properties variations with temperature. A special method for calculating the aerodynamic heat flux entering the nose cap from its surface is proposed. This method is characterized by very low computational costs and allows calculating the aerodynamic heat flux at different values of the Mach number and angles of attack which may vary during the aerodynamic heating. The numerical results obtained by the proposed approach are compared with the numerical results and experimental data obtained by other authors. The developed approach has been used for studying the impact of the angle of attack on the thermoelastic behavior of nose caps main components.

Finite-time and finite-size scalings in the evaluation of large-deviation functions: Numerical approach in continuous time.

PubMed

Guevara Hidalgo, Esteban; Nemoto, Takahiro; Lecomte, Vivien

2017-06-01

Rare trajectories of stochastic systems are important to understand because of their potential impact. However, their properties are by definition difficult to sample directly. Population dynamics provides a numerical tool allowing their study, by means of simulating a large number of copies of the system, which are subjected to selection rules that favor the rare trajectories of interest. Such algorithms are plagued by finite simulation time and finite population size, effects that can render their use delicate. In this paper, we present a numerical approach which uses the finite-time and finite-size scalings of estimators of the large deviation functions associated to the distribution of rare trajectories. The method we propose allows one to extract the infinite-time and infinite-size limit of these estimators, which-as shown on the contact process-provides a significant improvement of the large deviation function estimators compared to the standard one.

On energy harvesting from a vibro-impact oscillator with dielectric membranes

NASA Astrophysics Data System (ADS)

Lai, Z. H.; Thomson, G.; Yurchenko, D.; Val, D. V.; Rodgers, E.

2018-07-01

A vibro-impact mechanical system comprising of a ball moving freely between two dielectric membranes located at a certain distance from each other is studied. The system generates electricity when the ball moving due ambient vibrations impacts one of the membranes. The energy harvesting principle of the proposed system is explained and then used to formulate a numerical model for estimating the system output voltage. The dynamic behavior and output performance of the system are thoroughly studied under a harmonic excitation, as well as different initial conditions and various values of the restitution coefficient of the membranes. The delivered research results are useful for selecting the system parameters to achieve its optimal output performance in a realistic vibrational environment. Potential application of the proposed system for energy harvesting from car engine vibrations is presented.

Study of low-velocity impact response of sandwich panels with shear-thickening gel cores

NASA Astrophysics Data System (ADS)

Wang, Yunpeng; Gong, Xinglong; Xuan, Shouhu

2018-06-01

The low-velocity impact response of sandwich panels with shear-thickening gel cores was studied. The impact tests indicated that the sandwich panels with shear-thickening gel cores showed excellent properties of energy dissipation and stress distribution. In comparison to the similar sandwich panels with chloroprene rubber cores and ethylene-propylene-diene monomer cores, the shear-thickening gel cores led to the obviously smaller contact forces and the larger energy absorptions. Numerical modelling with finite element analysis was used to investigate the stress distribution of the sandwich panels with shear-thickening gel cores and the results agreed well with the experimental results. Because of the unique mechanical property of the shear-thickening gel, the concentrated stress on the front facesheets were distributed to larger areas on the back facesheets and the peak stresses were reduced greatly.

Residential Segregation,Spatial Mismatch and Economic Growth across US Metropolitan Area

DOE Office of Scientific and Technical Information (OSTI.GOV)

Campbell, Dr Harrison; Li, Huiping

2013-01-01

Numerous studies have demonstrated the detrimental influence of residential segregation on poor inner-city residents. This study examines the impact of residential segregation on the welfare of populations in US metropolitan areas using economic growth as the indicator. Panel data of US metropolitan areas spanning 25 years, 1980 2005, are used to analyze the effect of segregation on economic growth. The results show that both racial and skill segregation have a negative impact on short and long-term economic growth, which have increased over time. Further, the negative impact of the variables associated with spatial mismatch is also revealed. The results clearlymore » point to the need for mobility policies that favor non-White households and comprehensive strategies that promote economic opportunities in low-resource communities in the US.« less

Impact of finite rate chemistry on the hydrodynamic stability of shear flows in turbulent lean premixed combustion

NASA Astrophysics Data System (ADS)

Dagan, Yuval; Ghoniem, Ahmed

2017-11-01

Recent experimental observations show that the dynamic response of a reactive flow is strongly impacted by the fuel chemistry. In order to gain insight into some of the underlying mechanisms we formulate a new linear stability model that incorporates the impact of finite rate chemistry on the hydrodynamic stability of shear flows. Contrary to previous studies which typically assume that the velocity field is independent of the kinetic rates, the velocity field in our study is coupled with the temperature field. Using this formulation, we reproduce previous results, e.g., most unstable global modes, obtained for non-reacting shear flow. Moreover, we show that these modes are significantly altered in frequency and gain by the presence of a reaction region within the shear layer. This qualitatively agrees with results of our recent experimental and numerical studies, which show that the flame surface location relative to the shear layer influences the stability characteristics in combustion tunnels. This study suggests a physical explanation for the observed impact of finite rate chemistry on shear flow stability.

Ecosystem services in urban water investment.

PubMed

Kandulu, John M; Connor, Jeffery D; MacDonald, Darla Hatton

2014-12-01

Increasingly, water agencies and utilities have an obligation to consider the broad environmental impacts associated with investments. To aid in understanding water cycle interdependencies when making urban water supply investment decisions, an ecosystem services typology was augmented with the concept of integrated water resources management. This framework is applied to stormwater harvesting in a case study catchment in Adelaide, South Australia. Results show that this methodological framework can effectively facilitate systematic consideration and quantitative assessment of broad environmental impacts of water supply investments. Five ecosystem service impacts were quantified including provision of 1) urban recreational amenity, 2) regulation of coastal water quality, 3) salinity, 4) greenhouse gas emissions, and 5) support of estuarine habitats. This study shows that ignoring broad environmental impacts can underestimate ecosystem service benefits of water supply investments by a value of up to A$1.36/kL, or three times the cost of operating and maintenance of stormwater harvesting. Rigorous assessment of the public welfare impacts of water infrastructure investments is required to guide long-term optimal water supply investment decisions. Numerous challenges remain in the quantification of broad environmental impacts of a water supply investment including a lack of peer-reviewed studies of environmental impacts, aggregation of incommensurable impacts, potential for double-counting errors, uncertainties in available impact estimates, and how to determine the most suitable quantification technique. Copyright © 2014 Elsevier Ltd. All rights reserved.

Hypervelocity impact simulations of Whipple shields

NASA Technical Reports Server (NTRS)

Segletes, Steven B.; Zukas, Jonas A.

1992-01-01

The problem associated with protecting space vehicles from space debris impact is described. Numerical simulation is espoused as a useful complement to experimentation: as a means to help understand and describe the hypervelocity impact phenomena. The capabilities of a PC-based hydrocode, ZeuS, are described, for application to the problem of hypervelocity impact. Finally, results of ZeuS simulations, as applied to the problem of bumper shield impact, are presented and compared with experimental results.

Integrating impact evaluation in the design and implementation of monitoring marine protected areas

PubMed Central

Ahmadia, Gabby N.; Glew, Louise; Provost, Mikaela; Gill, David; Hidayat, Nur Ismu; Mangubhai, Sangeeta; Purwanto; Fox, Helen E.

2015-01-01

Quasi-experimental impact evaluation approaches, which enable scholars to disentangle effects of conservation interventions from broader changes in the environment, are gaining momentum in the conservation sector. However, rigorous impact evaluation using statistical matching techniques to estimate the counterfactual have yet to be applied to marine protected areas (MPAs). While there are numerous studies investigating ‘impacts’ of MPAs that have generated considerable insights, results are variable. This variation has been linked to the biophysical and social context in which they are established, as well as attributes of management and governance. To inform decisions about MPA placement, design and implementation, we need to expand our understanding of conditions under which MPAs are likely to lead to positive outcomes by embracing advances in impact evaluation methodologies. Here, we describe the integration of impact evaluation within an MPA network monitoring programme in the Bird's Head Seascape, Indonesia. Specifically we (i) highlight the challenges of implementation ‘on the ground’ and in marine ecosystems and (ii) describe the transformation of an existing monitoring programme into a design appropriate for impact evaluation. This study offers one potential model for mainstreaming impact evaluation in the conservation sector. PMID:26460128

Numerical modeling of the destruction of steel plates with a gradient substrate

NASA Astrophysics Data System (ADS)

Orlov, M. Yu.; Glazyrin, V. P.; Orlov, Yu. N.

2017-10-01

The paper presents the results of numerical simulation of the shock loading process of steel barriers with a gradient substrate. In an elastic plastic axisymmetric statement, a shock is simulated along the normal in the range of initial velocities up to 300 m / s. A range of initial velocities was revealed, in which the presence of a substrate "saved" the obstacle from spallation. New tasks were announced to deepen scientific knowledge about the behavior of unidirectional gradient barriers at impact. The results of calculations are obtained in the form of graphs, calculated configurations of the "impact - barrier" and tables.

Diattenuation of brain tissue and its impact on 3D polarized light imaging

PubMed Central

Menzel, Miriam; Reckfort, Julia; Weigand, Daniel; Köse, Hasan; Amunts, Katrin; Axer, Markus

2017-01-01

3D-polarized light imaging (3D-PLI) reconstructs nerve fibers in histological brain sections by measuring their birefringence. This study investigates another effect caused by the optical anisotropy of brain tissue – diattenuation. Based on numerical and experimental studies and a complete analytical description of the optical system, the diattenuation was determined to be below 4 % in rat brain tissue. It was demonstrated that the diattenuation effect has negligible impact on the fiber orientations derived by 3D-PLI. The diattenuation signal, however, was found to highlight different anatomical structures that cannot be distinguished with current imaging techniques, which makes Diattenuation Imaging a promising extension to 3D-PLI. PMID:28717561

Sunspot: A program to model the behavior of hypervelocity impact damaged multilayer insulation in the Sunspot thermal vacuum chamber of Marshall Space Flight Center

NASA Technical Reports Server (NTRS)

Rule, W. K.; Hayashida, K. B.

1992-01-01

The development of a computer program to predict the degradation of the insulating capabilities of the multilayer insulation (MLI) blanket of Space Station Freedom due to a hypervelocity impact with a space debris particle is described. A finite difference scheme is used for the calculations. The computer program was written in Microsoft BASIC. Also described is a test program that was undertaken to validate the numerical model. Twelve MLI specimens were impacted at hypervelocities with simulated debris particles using a light gas gun at Marshall Space Flight Center. The impact-damaged MLI specimens were then tested for insulating capability in the space environment of the Sunspot thermal vacuum chamber at MSFC. Two undamaged MLI specimens were also tested for comparison with the test results of the damaged specimens. The numerical model was found to adequately predict behavior of the MLI specimens in the Sunspot chamber. A parameter, called diameter ratio, was developed to relate the nominal MLI impact damage to the apparent (for thermal analysis purposes) impact damage based on the hypervelocity impact conditions of a specimen.

METROPOLITAN-SCALE TRANSPORT AND DISPERSION FROM THE NEW YORK WORLD TRADE CENTER FOLLOWING SEPTEMBER 11, 2001. PART I: AN EVALUATION OF THE CALMET METEOROLOGICAL MODEL

EPA Science Inventory

Following the collapse of the New York City World Trade Center towers on September 11, 2001, Local, State and Federal agencies initiated numerous air monitoring activities to better understand the impact of emissions from the disaster. A study of the estimated pathway that a pote...

The simulation of the non-Markovian behaviour of a two-level system

NASA Astrophysics Data System (ADS)

Semina, I.; Petruccione, F.

2016-05-01

Non-Markovian relaxation dynamics of a two-level system is studied with the help of the non-linear stochastic Schrödinger equation with coloured Ornstein-Uhlenbeck noise. This stochastic Schrödinger equation is investigated numerically with an adapted Platen scheme. It is shown, that the memory effects have a significant impact to the dynamics of the system.

How Does Research Evaluation Impact Educational Research? Exploring Intended and Unintended Consequences of Research Assessment in the United Kingdom, 1986-2014

ERIC Educational Resources Information Center

Marques, Marcelo; Powell, Justin J. W.; Zapp, Mike; Biesta, Gert

2017-01-01

Research evaluation systems in many countries aim to improve the quality of higher education. Among the first of such systems, the UK's Research Assessment Exercise (RAE) dating from 1986 is now the Research Excellence Framework (REF). Highly institutionalised, it transforms research to be more accountable. While numerous studies describe the…

The Relationship between School-Wide Implementation of Positive Behavior Intervention and Supports and Student Discipline Outcomes

ERIC Educational Resources Information Center

Childs, Karen Elfner; Kincaid, Don; George, Heather Peshak; Gage, Nicholas A.

2016-01-01

School-Wide Positive Behavior Interventions and Supports (SWPBIS) is a systems approach to supporting the social and emotional needs of all children utilized by more than 21,000 schools across the nation. Data from numerous studies and state projects' evaluation reports point to the impact of SWPBIS on student outcomes (office discipline referrals…

Determinants of project success

NASA Technical Reports Server (NTRS)

Murphy, D. C.; Baker, B. N.; Fisher, D.

1974-01-01

The interactions of numerous project characteristics, with particular reference to project performance, were studied. Determinants of success are identified along with the accompanying implications for client organization, parent organization, project organization, and future research. Variables are selected which are found to have the greatest impact on project outcome, and the methodology and analytic techniques to be employed in identification of those variables are discussed.

Impact of fire in two old-growth montane longleaf pine stands

Treesearch

John S. Kush; John C. Gilbert; Crystal Lupo; Na Zhou; Becky Barlow

2013-01-01

The structure of longleaf pine (Pinus palustris Mill.) forests of the Southeastern United States Coastal Plains has been the focus of numerous studies. By comparison, the forests in the mountains of Alabama and Georgia are not well understood. Less than 1 percent of longleaf pine stands found in the montane portion of longleaf’s range are considered...

Teaching Students How to Research the Past: Historians and Librarians in the Digital Age

ERIC Educational Resources Information Center

Daniel, Dominique

2012-01-01

In this article, the author examines some issues linked to the impact of new technologies on teaching. In a 2003 survey, respondents stressed that the priority was to understand "how new media are changing student learning." There are by now numerous studies that attempt to assess how students conduct research and learn in the digital age, but…

Cultural Diversity as Resistance to Neoliberal Globalization: The Emergence of a Global Movement and Convention

ERIC Educational Resources Information Center

Chan-Tibergien, Jennifer

2006-01-01

While there have been numerous discussions of the impact on educational services made by trade liberalization through the World Trade Organization (WTO), this study looks at the emergence of global resistance to the commodification of culture through the General Agreement on Trade in Services (GATS) within the WTO. In line with the Council of…

The Impact of Bullying on School Performance in Six Selected Schools in South Carolina

ERIC Educational Resources Information Center

Cooper, Stephanie A.

2011-01-01

The nation's K-12 schools are faced with numerous critical challenges, such as elevating academic achievement, and meeting No Child Left Behind state standards (Kowalski et al., 2008). But bullying in schools is becoming one of the most challenging issues that school personnel are encountering. In a Stanford University, study it was revealed that…

Small-body deflection techniques using spacecraft: Techniques in simulating the fate of ejecta

NASA Astrophysics Data System (ADS)

Schwartz, Stephen R.; Yu, Yang; Michel, Patrick; Jutzi, Martin

2016-04-01

We define a set of procedures to numerically study the fate of ejecta produced by the impact of an artificial projectile with the aim of deflecting an asteroid. Here we develop a simplified, idealized model of impact conditions that can be adapted to fit the details of specific deflection-test scenarios, such as what is being proposed for the AIDA project. Ongoing studies based upon the methodology described here can be used to inform observational strategies and safety conditions for an observing spacecraft. To account for ejecta evolution, the numerical strategies we are employing are varied and include a large N-Body component, a smoothed-particle hydrodynamics (SPH) component, and an application of impactor scaling laws. Simulations that use SPH-derived initial conditions show high-speed ejecta escaping at low angles of inclination, and very slowly moving ejecta lofting off the surface at higher inclination angles, some of which reimpacts the small-body surface. We are currently investigating the realism of this and other models' behaviors. Next steps will include the addition of solar perturbations to the model and applying the protocol developed here directly to specific potential mission concepts such as the proposed AIDA scenario.

Non-Maxwellian fast particle effects in gyrokinetic GENE simulations

NASA Astrophysics Data System (ADS)

Di Siena, A.; Görler, T.; Doerk, H.; Bilato, R.; Citrin, J.; Johnson, T.; Schneider, M.; Poli, E.; JET Contributors

2018-04-01

Fast ions have recently been found to significantly impact and partially suppress plasma turbulence both in experimental and numerical studies in a number of scenarios. Understanding the underlying physics and identifying the range of their beneficial effect is an essential task for future fusion reactors, where highly energetic ions are generated through fusion reactions and external heating schemes. However, in many of the gyrokinetic codes fast ions are, for simplicity, treated as equivalent-Maxwellian-distributed particle species, although it is well known that to rigorously model highly non-thermalised particles, a non-Maxwellian background distribution function is needed. To study the impact of this assumption, the gyrokinetic code GENE has recently been extended to support arbitrary background distribution functions which might be either analytical, e.g., slowing down and bi-Maxwellian, or obtained from numerical fast ion models. A particular JET plasma with strong fast-ion related turbulence suppression is revised with these new code capabilities both with linear and nonlinear gyrokinetic simulations. It appears that the fast ion stabilization tends to be less strong but still substantial with more realistic distributions, and this improves the quantitative power balance agreement with experiments.

Assessing the performances of low impact development alternatives by long-term simulation for a semi-arid area in Tianjin, northern China.

PubMed

Huang, Jinhui Jeanne; Li, Yu; Niu, Shuai; Zhou, Shu H

2014-01-01

For areas that are urbanized rapidly, the practice of low impact development (LID) has gained an important place in stormwater management and urban planning due to its capability and beneficial effects in restoring the original hydrological cycle. The performances of LID alternatives can vary substantially due to different climate conditions. This study investigated the performances of five LID alternatives under a semi-arid climate in northern China on water balance and flood control. A numerical model, Storm Water Management Model version 5 (US Environmental Protection Agency), was employed to run 10 years' rainfall events for these objectives. Two evaluation methods were proposed in this study: the efficiency index for water balance and a performance radar chart. The investigation of the five LID alternatives revealed that these LID alternatives functioned differently in flood control and water balance, and porous pavement performed best in all indices except the lag time. The two evaluation methods, in conjunction with the long-term numerical simulation, can facilitate design and decision making by providing a clear picture of the performance and functions for these LID alternatives.

Examining the impact of lahars on buildings using numerical modelling

NASA Astrophysics Data System (ADS)

Mead, Stuart R.; Magill, Christina; Lemiale, Vincent; Thouret, Jean-Claude; Prakash, Mahesh

2017-05-01

Lahars are volcanic flows containing a mixture of fluid and sediment which have the potential to cause significant damage to buildings, critical infrastructure and human life. The extent of this damage is controlled by properties of the lahar, location of elements at risk and susceptibility of these elements to the lahar. Here we focus on understanding lahar-induced building damage. Quantification of building damage can be difficult due to the complexity of lahar behaviour (hazard), varying number and type of buildings exposed to the lahar (exposure) and the uncertain susceptibility of buildings to lahar impacts (vulnerability). In this paper, we quantify and examine the importance of lahar hazard, exposure and vulnerability in determining building damage with reference to a case study in the city of Arequipa, Peru. Numerical modelling is used to investigate lahar properties that are important in determining the inundation area and forces applied to buildings. Building vulnerability is quantified through the development of critical depth-pressure curves based on the ultimate bending moment of masonry structures. In the case study area, results suggest that building strength plays a minor role in determining overall building losses in comparison to the effects of building exposure and hydraulic characteristics of the lahar.

Nonlinear modelling in time domain numerical analysis of stringed instrument dynamics

NASA Astrophysics Data System (ADS)

Bielski, Paweł; Kujawa, Marcin

2017-03-01

Musical instruments are very various in terms of sound quality with their timbre shaped by materials and geometry. Materials' impact is commonly treated as dominant one by musicians, while it is unclear whether it is true or not. The research proposed in the study focuses on determining influence of both these factors on sound quality based on their impact on harmonic composition. Numerical approach has been chosen to allowed independent manipulation of geometrical and material parameters as opposed to experimental study subjected to natural randomness of instrument construction. Distinctive element of this research is precise modelling of whole instrument and treating it as one big vibrating system instead of performing modal analysis on an isolated part. Finite elements model of a stringed instrument has been built and a series of nonlinear time-domain dynamic analyses were executed to obtain displacement signals and perform subsequent spectral analysis. Precision of computations seems sufficient to determine the influence of instrument's macroscopic mechanical parameters on timbre. Further research should focus on implementation of acoustic medium in attempt to include dissipation and synchronization mechanisms. Outside the musical field this kind of research could be potentially useful in noise reduction problems.

Phytoplankton and Climate

NASA Technical Reports Server (NTRS)

Moisan, John R.

2009-01-01

Ocean phytoplankton supply about half of the oxygen that humans utilize to sustain life. In this lecture, we will explore how phytoplankton plays a critical role in modulating the Earth's climate. These tiny organisms are the base of the Ocean's food web. They can modulate the rate at which solar heat is absorbed by the ocean, either through direct absorption or through production of highly scattering cellular coverings. They take up and help sequester carbon dioxide, a key greenhouse gas that modulated the Earth's climate. They are the source of cloud nucleation gases that are key to cloud formation/processes. They are also able to modify the nutrient budgets of the ocean through active uptake of inert atmospheric nitrogen. Climate variations have a pronounced impact on phytoplankton dynamics. Long term variations in the climate have been studied through geological interpretations on its influence on phytoplankton populations. The presentation will focus on presenting the numerous linkages that have been observed between climate and phytoplankton and further discuss how present climate change scenarios are likely to impact phytoplankton populations as well as present findings from several studies that have tried to understand how the climate might react to the feedbacks from these numerous climate-phytop|ankton linkages.

The dynamic properties behavior of high strength concrete under different strain rate

NASA Astrophysics Data System (ADS)

Abdullah, Hasballah; Husin, Saiful; Umar, Hamdani; Rizal, Samsul

2005-04-01

This paper present a number experimental data and numerical technique used in the dynamic behavior of high strength concrete. A testing device is presented for the experimental study of dynamic behavior material under high strain rates. The specimen is loaded by means of a high carbon steel Hopkinson pressure bar (40 mm diameter, 3000 mm long input bar and 1500 mm long out put bar) allowing for the testing of specimen diameter is large enough in relation to the size of aggregates. The other method also proposed for measuring tensile strength, the measurement method based on the superposition and concentration of tensile stress wave reflected both from the free-free ends of striking bar and the specimen bar. The compression Hopkinson bar test, the impact tensile test of high strength concrete bars are performed, together with compression static strength test. In addition, the relation between break position under finite element simulation and impact tensile strength are examined. The three-dimensional simulation of the specimen under transient loading are presented and comparisons between the experimental and numerical simulation on strain rate effects of constitutive law use in experimental are study.

Atmospheric Effects of Subsonic Aircraft: Interim Assessment Report of the Advanced Subsonic Technology Program

NASA Technical Reports Server (NTRS)

Friedl, Randall R. (Editor)

1997-01-01

This first interim assessment of the subsonic assessment (SASS) project attempts to summarize concisely the status of our knowledge concerning the impacts of present and future subsonic aircraft fleets. It also highlights the major areas of scientific uncertainty, through review of existing data bases and model-based sensitivity studies. In view of the need for substantial improvements in both model formulations and experimental databases, this interim assessment cannot provide confident numerical predictions of aviation impacts. However, a number of quantitative estimates are presented, which provide some guidance to policy makers.

Energy harvesting from a DE-based dynamic vibro-impact system

NASA Astrophysics Data System (ADS)

Yurchenko, D.; Val, D. V.; Lai, Z. H.; Gu, G.; Thomson, G.

2017-10-01

Dielectric elastomer (DE) generators may be used in harvesting energy from ambient vibrations. Based on existing research on the mechanical properties of a circular DE membrane, a DE-based dynamic vibro-impact system is proposed in this paper to convert vibrational energy into electrical one. The dimensional, electrical and dynamic parameters of the DE membrane are analysed and then used to numerically estimate the output voltage of the proposed system. The system output performances under harmonic excitation are further discussed. At last, the comparison study has been conducted with an electromagnetic energy harvesting system, served as a ‘shaking’ flashlight.

A global numerical study of radon-222 and lead-210 in the atmosphere using the AES and York University CDT General Circulation Model (AYCG)

NASA Technical Reports Server (NTRS)

Beagley, Stephen R.; Degrandpre, Jean; Mcconnell, John C.; Laprise, Rene; Mcfarlane, Norman

1994-01-01

The Canadian Climate Center (CCC) GCM has been modified to allow its use for studies in atmospheric chemistry. The initial experiments reported here have been run to test and allow sensitivity studies of the new transport module. The impact of different types of parameterization for the convective mixing have been studied based on the large scale evolution of Rn-222 and Pb-210. Preliminary results have shown that the use of a scheme, which mixes unstable columns over a very short time scale, produces a global distribution of lead that agrees in some aspects with observations. The local impact of different mixing schemes on a short lived tracer like the radon is very important.

Urban Modification of Convection and Rainfall in Complex Terrain

NASA Astrophysics Data System (ADS)

Freitag, B. M.; Nair, U. S.; Niyogi, D.

2018-03-01

Despite a globally growing proportion of cities located in regions of complex terrain, interactions between urbanization and complex terrain and their meteorological impacts are not well understood. We utilize numerical model simulations and satellite data products to investigate such impacts over San Miguel de Tucumán, Argentina. Numerical modeling experiments show urbanization results in 20-30% less precipitation downwind of the city and an eastward shift in precipitation upwind. Our experiments show that changes in surface energy, boundary layer dynamics, and thermodynamics induced by urbanization interact synergistically with the persistent forcing of atmospheric flow by complex terrain. With urbanization increasing in mountainous regions, land-atmosphere feedbacks can exaggerate meteorological forcings leading to weather impacts that require important considerations for sustainable development of urban regions within complex terrain.

Numerical model of solar dynamic radiator for parametric analysis

NASA Technical Reports Server (NTRS)

Rhatigan, Jennifer L.

1989-01-01

Growth power requirements for Space Station Freedom will be met through addition of 25 kW solar dynamic (SD) power modules. Extensive thermal and power cycle modeling capabilities have been developed which are powerful tools in Station design and analysis, but which prove cumbersome and costly for simple component preliminary design studies. In order to aid in refining the SD radiator to the mature design stage, a simple and flexible numerical model was developed. The model simulates heat transfer and fluid flow performance of the radiator and calculates area mass and impact survivability for many combinations of flow tube and panel configurations, fluid and material properties, and environmental and cycle variations.

A variational principle for compressible fluid mechanics. Discussion of the one-dimensional theory

NASA Technical Reports Server (NTRS)

Prozan, R. J.

1982-01-01

The second law of thermodynamics is used as a variational statement to derive a numerical procedure to satisfy the governing equations of motion. The procedure, based on numerical experimentation, appears to be stable provided the CFL condition is satisfied. This stability is manifested no matter how severe the gradients (compression or expansion) are in the flow field. For reasons of simplicity only one dimensional inviscid compressible unsteady flow is discussed here; however, the concepts and techniques are not restricted to one dimension nor are they restricted to inviscid non-reacting flow. The solution here is explicit in time. Further study is required to determine the impact of the variational principle on implicit algorithms.

Numerical studies of depressurization-induced gas production from an interbedded marine turbidite gas hydrate reservoir model

USGS Publications Warehouse

Myshakin, Evgeniy; Lin, Jeen-Shang; Uchida, Shun; Seol, Yongkoo; Collett, Timothy S.; Boswell, Ray

2017-01-01

The numerical simulation of thin hydrate-bearing sand layers interbedded with mud layers is investigated. In this model, the lowest hydrate layer occurs at the base of gas hydrate stability and overlies a thinly-interbedded saline aquifer. The predicted gas rates reach 6.25 MMscf/day (1.77 x 105 m3 /day) after 90 days of continuous depressurization with manageable water production. Development of horizontal dissociating interfaces between hydrate-bearing sand and mud layers is a primary determinant of reservoir performance. A set of simulations has been executed to assess uncertainty in in situ permeability and to determine the impact of the saline aquifer on productivity.

Economic Assessment of Correlated Energy-Water Impacts using Computable General Equilibrium Modeling

NASA Astrophysics Data System (ADS)

Qiu, F.; Andrew, S.; Wang, J.; Yan, E.; Zhou, Z.; Veselka, T.

2016-12-01

Many studies on energy and water are rightfully interested in the interaction of water and energy, and their projected dependence into the future. Water is indeed an essential input to the power sector currently, and energy is required to pump water for end use in either household consumption or in industrial uses. However, each presented study either qualitatively discusses the issues, particularly about how better understanding the interconnectedness of the system is paramount in getting better policy recommendations, or considers a partial equilibrium framework where water use and energy use changes are considered explicitly without thought to other repercussions throughout the regional/national/international economic landscapes. While many studies are beginning to ask the right questions, the lack of numerical rigor raises questions of concern in conclusions discerned. Most use life cycle analysis as a method for providing numerical results, though this lacks the flexibility that economics can provide. In this study, we will perform economic analysis using computable general equilibrium models with energy-water interdependencies captured as an important factor. We atempt to answer important and interesting questions in the studies: how can we characterize the economic choice of energy technology adoptions and their implications on water use in the domestic economy. Moreover, given predictions of reductions in rain fall in the near future, how does this impact the water supply in the midst of this energy-water trade-off?

Groundwater flow and heat transport for systems undergoing freeze-thaw: Intercomparison of numerical simulators for 2D test cases

DOE PAGES

Grenier, Christophe; Anbergen, Hauke; Bense, Victor; ...

2018-02-26

In high-elevation, boreal and arctic regions, hydrological processes and associated water bodies can be strongly influenced by the distribution of permafrost. Recent field and modeling studies indicate that a fully-coupled multidimensional thermo-hydraulic approach is required to accurately model the evolution of these permafrost-impacted landscapes and groundwater systems. However, the relatively new and complex numerical codes being developed for coupled non-linear freeze-thaw systems require verification. Here in this paper, this issue is addressed by means of an intercomparison of thirteen numerical codes for two-dimensional test cases with several performance metrics (PMs). These codes comprise a wide range of numerical approaches, spatialmore » and temporal discretization strategies, and computational efficiencies. Results suggest that the codes provide robust results for the test cases considered and that minor discrepancies are explained by computational precision. However, larger discrepancies are observed for some PMs resulting from differences in the governing equations, discretization issues, or in the freezing curve used by some codes.« less

Numerical predictions of shock propagation through unreactive and reactive liquids with experimental validation

NASA Astrophysics Data System (ADS)

Stekovic, Svjetlana; Nissen, Erin; Bhowmick, Mithun; Stewart, Donald S.; Dlott, Dana D.

2017-06-01

The objective of this work is to numerically analyze shock behavior as it propagates through compressed, unreactive and reactive liquid, such as liquid water and liquid nitromethane. Parameters, such as pressure and density, are analyzed using the Mie-Gruneisen EOS and each multi-material system is modeled using the ALE3D software. The motivation for this study is based on provided high-resolution, optical interferometer (PDV) and optical pyrometer measurements. In the experimental set-up, a liquid is placed between an Al 1100 plate and Pyrex BK-7 glass. A laser-driven Al 1100 flyer impacts the plate, causing the liquid to be highly compressed. The numerical model investigates the influence of the high pressure, shock-compressed behavior in each liquid, the energy transfer, and the wave impedance at the interface of each material in contact. The numerical results using ALE3D will be validated by experimental data. This work aims to provide further understanding of shock-compressed behavior and how the shock influences phase transition in each liquid.

Groundwater flow and heat transport for systems undergoing freeze-thaw: Intercomparison of numerical simulators for 2D test cases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grenier, Christophe; Anbergen, Hauke; Bense, Victor

In high-elevation, boreal and arctic regions, hydrological processes and associated water bodies can be strongly influenced by the distribution of permafrost. Recent field and modeling studies indicate that a fully-coupled multidimensional thermo-hydraulic approach is required to accurately model the evolution of these permafrost-impacted landscapes and groundwater systems. However, the relatively new and complex numerical codes being developed for coupled non-linear freeze-thaw systems require verification. Here in this paper, this issue is addressed by means of an intercomparison of thirteen numerical codes for two-dimensional test cases with several performance metrics (PMs). These codes comprise a wide range of numerical approaches, spatialmore » and temporal discretization strategies, and computational efficiencies. Results suggest that the codes provide robust results for the test cases considered and that minor discrepancies are explained by computational precision. However, larger discrepancies are observed for some PMs resulting from differences in the governing equations, discretization issues, or in the freezing curve used by some codes.« less

Self-assembly of inorganic nanoparticles: Ab ovo

NASA Astrophysics Data System (ADS)

Kotov, Nicholas A.

2017-09-01

There are numerous remarkable studies related to the self-organization of polymers, coordination compounds, microscale particles, biomolecules, macroscale particles, surfactants, and reactive molecules on surfaces. The focus of this paper is on the self-organization of nanoscale inorganic particles or simply nanoparticles (NPs). Although there are fascinating and profound discoveries made with other self-assembling structures, the ones involving NPs deserve particular attention because they (a) are omnipresent in Nature; (b) have relevance to numerous disciplines (physics, chemistry, biology, astronomy, Earth sciences, and others); (c) embrace most of the features, geometries, and intricacies observed for the self-organization of other chemical species; (d) offer new tools for studies of self-organization phenomena; and (e) have a large economic impact, extending from energy and construction industries, to optoelectronics, biomedical technologies, and food safety. Despite the overall success of the field it is necessary to step back from its multiple ongoing research venues and consider two questions: What is self-assembly of nanoparticles? and Why do we need to study it? The reason to bring them up is to achieve greater scientific depth in the understanding of these omnipresent phenomena and, perhaps, deepen their multifaceted impact. Contribution to the Focus Issue Self-assemblies of Inorganic and Organic Nanomaterials edited by Marie-Paule Pileni.